WorldWideScience

Sample records for yb doped inp

  1. Proton irradiation induced defects in Cd and Zn doped InP

    International Nuclear Information System (INIS)

    Rybicki, G.C.; Williams, W.S.

    1993-01-01

    Proton irradiation induced defects in Zn and Cd doped InP have been studied by deep level transient spectroscopy, (DLTS). After 2 MeV proton irradiation the defects H4 and H5 were observed in lightly Zn doped InP, while the defects H3 and H5 were observed in more heavily Zn and Cd doped InP. The defect properties were not affected by the substitution of Cd for Zn, but the introduction rate of H5 was lower in Cd doped InP. The annealing rate of defects was also higher in Cd doped InP. The use of Cd doped InP may thus result in an InP solar cell with even greater radiation resistance

  2. Preparation and spectroscopic properties of Yb-doped and Yb-Al-codoped high silica glasses

    International Nuclear Information System (INIS)

    Qiao Yanbo; Wen Lei; Wu Botao; Ren Jinjun; Chen Danping; Qiu Jianrong

    2008-01-01

    Yb-doped and Yb-Al-codoped high silica glasses have been prepared by sintering nanoporous glasses. The absorption, fluorescent spectra and fluorescent lifetimes have been measured and the emission cross-section and minimum pump intensities were calculated. Codoping aluminum ions enhanced the fluorescence intensity of Yb-doped high silica glass obviously. The emission cross-sections of Yb-doped and Yb-Al-codoped high silica glasses were 0.65 and 0.82 pm 2 , respectively. The results show that Yb-Al-codoped high silica glass has better spectroscopic properties for a laser material. The study of high silica glass doped with ytterbium is helpful for its application in Yb laser systems, especially for high-power and high-repetition lasers

  3. Photoacoustic investigation of doped InP using open cell configuration

    NARCIS (Netherlands)

    George, S.D.; Vallabhan, C.P.G.; Heck, M.J.R.; Radhakrishnan, P.; Nampoori, V.P.N.

    2002-01-01

    An open cell photoacoustic (PA) configuration was employed to evaluate the thermal diffusivity of intrinsic InP as well as InP doped with tin and iron. Thermal diffusivity data were evaluated from variation of phase of PA signal as a function of modulation frequency. In doped samples, we observe a

  4. A unified calculation of the optical spectral band positions and electron paramagnetic resonance spectral data for Yb3+ in InP semiconductor

    International Nuclear Information System (INIS)

    Feng Wenlin; Zheng Wenchen; Liu Honggang; Li, X.M.

    2011-01-01

    Highlights: → We found a energy matrix of 4f 13 ion in cubic crystals and external magnetic field. → Optical and EPR data of Yb 3+ : InP are explained by diagonalizing the energy matrix. → Signs of hyperfine structure constants A( 171 Yb 3+ ) and A( 173 Yb 3+ ) are determined. - Abstract: The complete energy matrix for a 4f 13 ion in cubic crystals and under an external magnetic field is established by means of the irreducible tensor operator and/or equivalent operator methods. By diagonalizing the energy matrix, four optical spectrum band positions and three spin-Hamiltonian parameters [g factor and hyperfine structure constants A( 171 Yb 3+ ) and A( 173 Yb 3+ )] for Yb 3+ in InP semiconductor are calculated together. The calculated results are in good agreement with the experimental values. The signs of hyperfine structure constants A( 171 Yb 3+ ) and A( 173 Yb 3+ ) are determined from the calculations. The results are discussed.

  5. Silicon doped InP as an alternative plasmonic material for mid-infrared

    DEFF Research Database (Denmark)

    Panah, Mohammad Esmail Aryaee; Han, Li; Christensen, Dennis Valbjørn

    2016-01-01

    Silicon-doped InP is grown on top of semiinsulating iron-doped and sulfur-doped InP substrates by metalorganic vapor phase epitaxy (MOVPE), and the growth parameters are adjusted to obtain various free carrier concentrations from 1.05×1019 cm-3 up to 3.28×1019 cm-3. Midinfrared (IR) reflection...

  6. Growth of semi-insulating InP through nuclear doping

    International Nuclear Information System (INIS)

    Aliyev, M.I; Rashidova, Sh.Sh; Huseynli, M.A.

    2012-01-01

    Full text : Semi-insulating semiconductors are widely used in so-called dielectronics. Dielectric devices have quick response, good frequency characteristics, a low noise level, low sensitivity to temperature changes, etc. One of the most promising semiconductor materials is InP. At present annealing and doping are commonly used techniques to grow semi-insulating InP. The aim of this work was to grow semi-insulating InP through nuclear doping (by irradiation with gamma-quanta). InP single crystals were obtained by Czochralski method. Specimens were irradiated with doses of 10kGr at room temperature. Electrical conductivity and Hall effect were measured before and after irradiation in the temperature range 77 to 320K. After irradiation reduction in electrical conductivity was observed. This fact can be associated with formation of M-centers in positively threefold charged states of vacancy and antisite defects. Under irradiation first Ini interstitial atoms and phosphorus vacancies form. Further, the Ini atoms occupy the phosphorus vacancies. As a result there appear InP antiste defects, which along with indium vacancies form V I nI n p + In p + + complexes of the acceptor type. These complexes turn out to be traps for charge carriers and electrical conductivity of irradiated InP are sharply reduced to semi-insulating specimens

  7. Mass fabrication of homogeneously Yb-doped silica nanoparticles and their spectroscopic properties

    International Nuclear Information System (INIS)

    Xiong Liangming; Sekiya, Edson H; Saito, Kazuya

    2009-01-01

    A large number of homogeneously Yb-doped silica nanoparticles were continually fabricated in a vapor synthesis route, in which the Yb doping level can be well controlled by varying either the heating temperature or the carrier gas flow rate of the Yb precursor. The sizes, shapes, and morphologies of the nanoparticles were examined, and no crystallites and no Yb 2 O 3 clusters were observed in the nanoparticles. These nanoparticles exhibit a clear Yb 3+ -derived absorption at around 973-975 nm and a dependence of the emission intensity and decay time on the doping level, much different from that of sintered pellets.

  8. Yb-doped aluminophosphosilicate ternary fiber with high efficiency and excellent laser stability

    Science.gov (United States)

    Li, Yuwei; Peng, Kun; Zhan, Huan; Liu, Shuang; Ni, Li; Wang, Yuying; Yu, Juan; Wang, Xiaolong; Wang, Jianjun; Jing, Feng; Lin, Aoxiang

    2018-03-01

    By using chelate precursor doping technique and traditional modified chemical vapor deposition system, we fabricated Yb-doped aluminophosphosilicate (Al2O3-P2O5-SiO2, ternary Yb-APS) large-mode-area fiber and reported on its laser performance. The fiber preform was doped with Al, P and Yb with concentration of ∼8000 ppm, ∼1700 ppm and ∼400 ppm in molar percent, respectively. Tested with master oscillator power amplifier system, the home-made Yb-APS fiber was found to present 1.02 kW at 1061.1 nm with a high slope efficiency of 81.2% and excellent laser stability with power fluctuation less than ±1.1% for over 10 h. Compared with Yb-doped aluminosilicate (Al2O3-SiO2, binary Yb-AS) fiber, the introduction of P2O5 effectively suppressed photodarkening effect even the P/Al ratio is much less than 1, indicating that Yb-APS fiber is a better candidate for high power fiber lasers.

  9. Surface Plasmons on Highly Doped InP

    DEFF Research Database (Denmark)

    Panah, Mohammad Esmail Aryaee; Ottaviano, Luisa; Semenova, Elizaveta

    2016-01-01

    Silicon doped InP is grown by metal-organic vapor phase epitaxy (MOVPE) using optimized growth parameters to achieve high free carrier concentration. Reflectance of the grown sample in mid-IR range is measured using FTIR and the result is used to retrieve the parameters of the dielectric function...

  10. Assessment of effect of Yb3+ ion pairs on a highly Yb-doped double-clad fibre laser

    Science.gov (United States)

    Vallés, J. A.; Martín, J. C.; Berdejo, V.; Cases, R.; Álvarez, J. M.; Rebolledo, M. Á.

    2018-03-01

    Using a previously validated characterization method based on the careful measurement of the characteristic parameters and fluorescence emission spectra of a highly Yb-doped double-clad fibre, we evaluate the contribution of ion pair induced processes to the output power of a double-clad Yb-doped fibre ring laser. This contribution is proved to be insignificant, contrary to analysis by other authors, who overestimate the role of ion pairs.

  11. Electronic and magnetic properties of digitally Ti doped InP: A first principles study

    International Nuclear Information System (INIS)

    Rahman, Gul; Cho, Sunglae; Hong, Soon Cheol

    2008-01-01

    Using the full-potential linearized augmented plane wave method within the generalized gradient approximation, we study the electronic and the magnetic properties of digitally Ti doped InP. It is quite interesting that digitally Ti-doped InP system shows half metallic ferromagnetism even though both bulk zinc blende TiP and InP are paramagnetic. We also investigate the electronic and the magnetic properties as a function of spacer layer thickness. Their properties such as exchange coupling constant and atomic projected density of states are more or less independent of the InP thickness. Spin density contour maps indicate that the spin-polarization is confined within the TiP plane. The system may show a highly anisotropic property in spin-polarized transport. (copyright 2008 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

  12. Dielectric relaxation in Yb-doped SrZrO3

    International Nuclear Information System (INIS)

    Kamishima, O; Abe, Y; Ishii, T; Kawamura, J; Hattori, T

    2004-01-01

    The dielectric constant of the proton conductor SrZr 1-x Yb x O 3 (x 0-0.1) was measured as a function of temperature and frequency. Two well-defined relaxation peaks were observed in SrZrO 3 doped with more than 1 mol% of Yb. The assignment of the two dielectric relaxations is discussed in terms of IR spectra and by free energy calculation for a miscibility of dopant Yb ions. The Yb concentration dependence of the relaxation strength of the two dielectric relaxations is in agreement with the results calculated from the free energy. The two relaxations can be assigned to a reorientation of a single Yb-OH dipole and of Yb-OH dipoles associated with Yb-clusters. The attractive energy for Yb-clustering in SrZrO 3 is evaluated at about -85 meV

  13. Overcoming doping limits in MOVPE grown n-doped InP for plasmonic applications

    DEFF Research Database (Denmark)

    Panah, Mohammad Esmail Aryaee; Xiao, Sanshui; Lavrinenko, Andrei

    2015-01-01

    Effect of the growth parameters on carrier concentration in MOVPE grown silicon-doped InP is studied. The dopant flow, V/III ratio and substrate temperature are optimized by considering the origin of the doping limits. In addition, two different group V precursors, namely PH3 and TBP, are compare......×1019cm-3 is achieved. Optical properties of the samples are investigated by Fourier transform infrared reflection (FTIR) spectroscopy and are fitted by a Drude-Lorentz function....

  14. Dielectric properties of semi-insulating Fe-doped InP in the terahertz spectral region.

    Science.gov (United States)

    Alyabyeva, L N; Zhukova, E S; Belkin, M A; Gorshunov, B P

    2017-08-04

    We report the values and the spectral dependence of the real and imaginary parts of the dielectric permittivity of semi-insulating Fe-doped InP crystalline wafers in the 2-700 cm -1 (0.06-21 THz) spectral region at room temperature. The data shows a number of absorption bands that are assigned to one- and two-phonon and impurity-related absorption processes. Unlike the previous studies of undoped or low-doped InP material, our data unveil the dielectric properties of InP that are not screened by strong free-carrier absorption and will be useful for designing a wide variety of InP-based electronic and photonic devices operating in the terahertz spectral range.

  15. Growth and laser action of Yb: YVO4 crystals with low Yb doping concentration

    Science.gov (United States)

    Zhong, Degao; Teng, Bing; Li, Jianhong; Zhang, Shiming; Zhang, Bingtao; Wang, Chao; Tian, Xueping; Liu, Junhai

    2012-11-01

    Yb: YVO4 single crystals with low doping concentrations of Yb3+ less than 0.3 at% were grown using the Czochralski method. The polarized absorption spectra were measured at room temperature. Strong anisotropy exists in the absorption spectra, resulting in almost entirely different features for π-polarization and σ-polarization. The laser emission spectrum and relationship curve between the output power and absorbed pump power (Pabs) were measured. The continuous-wave laser action of Yb: YVO4 single crystal in a range of 1020.4-1026.3 nm was realized by using a high-power diode laser as the pump source.

  16. Investigation of semi-insulating InP co-doped with Ti and various acceptors for use in X-ray detection

    International Nuclear Information System (INIS)

    Zdansky, K.; Gorodynskyy, V.; Kozak, H.; Pekarek, L.

    2005-01-01

    Semi-insulating InP single crystals co-doped with Zn and Ti and co-doped with Ti and Mn were grown by Czochralski technique. Wafers of these crystals were annealed for a long time at a high temperature and cooled slowly. The samples were characterized by temperature dependent resistivity and Hall coefficient measurements. The binding energies of Ti in semi-insulating InP co-doped with Ti and Zn and co-doped with Ti and Mn were found to differ which shows that Ti may occupy different sites in InP. The curves of Hall coefficient vs. reciprocal temperature deviate from straight lines at low temperatures due to electron and hole mixed conductance. The value of resistivity of the annealed semi-insulating InP co-doped with Ti and Mn reaches high resistivity at a reduced temperature easily achievable by thermo-electric devices which could make this material useable in X-ray detection. (copyright 2005 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

  17. Thermal stability of atom configurations around Er atoms doped in InP by OMVPE

    International Nuclear Information System (INIS)

    Ofuchi, Hironori; Ito, Takashi; Kawamoto, Takeshi; Tabuchi, Masao; Fujiwara, Yasufumi; Takeda, Yoshikazu

    1999-01-01

    It has been found that there is a threshold growth temperature between 550 deg C and 580 deg C for the change of local structure around Er atoms in InP doped Er atoms grown by organometallic vapor phase epitaxy (OMVPE). To understand whether the structure change is induced at the growing surface or during the growth as an in situ annealing, the thermal stability of the local structures around the Er atoms doped in InP by the OMVPE at 530 deg C has been investigated by the extended X-ray absorption fine structure (EXAFS). The EXAFS analysis revealed that the local structure around the Er atoms, which existed substitutionally on In sites in the InP lattice, was stable against the post-growth annealing even for 1 h at 650 deg C. Therefore, it is concluded that the local structures are formed on the growth front, and not in the volume of InP by thermal annealing during or after the growth. (author)

  18. Thermodynamic properties of multiferroic Mg doped YbMnO{sub 3}

    Energy Technology Data Exchange (ETDEWEB)

    Sattibabu, Bhumireddi, E-mail: bsb.satti@gmail.com [School of Engineering Sciences and Technology, University of Hyderabad, Hyderabad 500046 (India); Bhatnagar, A.K., E-mail: anilb42@gmail.com [School of Engineering Sciences and Technology, University of Hyderabad, Hyderabad 500046 (India); School of Physics, University of Hyderabad, Hyderabad 500046 (India); Samatham, S. Shanmukharao; Singh, D. [Low Temperature Laboratory, UGC-DAE Consortium for Scientific Research, University Campus, Khandwa Road, Indore 452001, M.P. (India); Rayaprol, S. [UGC-DAE Consortium for Scientific Research, Mumbai Centre, BARC Campus, Mumbai 400085 (India); Das, D. [School of Engineering Sciences and Technology, University of Hyderabad, Hyderabad 500046 (India); Siruguri, V. [UGC-DAE Consortium for Scientific Research, Mumbai Centre, BARC Campus, Mumbai 400085 (India); Ganesan, V. [Low Temperature Laboratory, UGC-DAE Consortium for Scientific Research, University Campus, Khandwa Road, Indore 452001, M.P. (India)

    2015-09-25

    Highlights: • Specific heat data shows that T{sub N} increases for Mg doped YbMnO{sub 3} from 83 K to 86 K. • Yb{sub 1−x}Mg{sub x}MnO{sub 3} (x = 0.0 and 0.05) shows multiple magnetic transitions. • RCP are found to be 26.1 J/mol and 27.2 J/mol for YbMnO{sub 3} and Yb{sub 0.95}Mg{sub 0.05}MnO{sub 3}. - Abstract: Calorimetric studies of polycrystalline samples Yb{sub 1−x}Mg{sub x}MnO{sub 3} with x = 0.0 and 0.05 are reported. It is revealed that the Mg doping raises the antiferromagnetic ordering temperature, T{sub N,} from 83 K for x = 0.0 to 86 K for x = 0.05. A ferromagnetic ordering is also observed around 3 K. The broad feature in the specific heat data just above ferromagnetic ordering, is attributed to the Schottky anomaly. The estimated effective molecular fields from the Schottky analysis are H{sub mf} = 3.0 and 3.5 T for YbMnO{sub 3} and Yb{sub 0.95}Mg{sub 0.05}MnO{sub 3}, respectively. High temperature shift of Schottky anomaly with Mg doping indicates increase in effective molecular field of Mn at the Yb 4b site. The data supports that the idea that although molecular field is mainly responsible for the Schottky anomaly in Yb{sub 1−x}Mg{sub x}MnO{sub 3} and Mn{sup 3+} spin ordering also affects it. Magnetic part of the specific heat is obtained by subtracting the lattice contribution estimated using two Debye temperatures. The magnetic entropy change (ΔS{sub mag}) for pure and doped samples are 2.0 J mol{sup −1} K{sup −1} and 2.1 J mol{sup −1} K{sup −1} respectively, while the relative cooling power (RCP) calculate 26.1 J/mol, 27.2 J/mol for a field change of 10 T.

  19. Yb-doped rod-type photonic crystal fibers for single-mode amplification

    DEFF Research Database (Denmark)

    Poli, Frederica; Passaro, Davide; Cucinotta, Annamaria

    2009-01-01

    The competition among the guided modes in rod-type photonic crystal fibers with a low refractive index ring in the Yb-doped core is investigated with an amplifier model to demonstrate the effective higher-order mode suppression.......The competition among the guided modes in rod-type photonic crystal fibers with a low refractive index ring in the Yb-doped core is investigated with an amplifier model to demonstrate the effective higher-order mode suppression....

  20. Structural analysis of erbium {delta}-doped InP by OMVPE with RBS-channeling

    Energy Technology Data Exchange (ETDEWEB)

    Yuhara, Junji; Takeda, Hitoshi; Matsubara, Naoki; Tabuchi, Masao; Fujiwara, Yasufumi; Morita, Kenji; Takeda, Yoshikazu [Nagoya Univ. (Japan). School of Engineering

    1997-03-01

    We have determined the lattice location of Er in InP {delta}-doped by OMVPE with RBS-channeling. Er concentrations along the <001> and <011> directions are same as random yields, while a significant flux peaking effect is seen for the <111> direction. These data suggest that Er atoms occupy the site equivalent to the hexahedral site in InP lattice. (author)

  1. Highly doped InP as a low loss plasmonic material for mid-IR region.

    Science.gov (United States)

    Panah, M E Aryaee; Takayama, O; Morozov, S V; Kudryavtsev, K E; Semenova, E S; Lavrinenko, A V

    2016-12-12

    We study plasmonic properties of highly doped InP in the mid-infrared (IR) range. InP was grown by metal-organic vapor phase epitaxy (MOVPE) with the growth conditions optimized to achieve high free electron concentrations by doping with silicon. The permittivity of the grown material was found by fitting the calculated infrared reflectance spectra to the measured ones. The retrieved permittivity was then used to simulate surface plasmon polaritons (SPPs) propagation on flat and structured surfaces, and the simulation results were verified in direct experiments. SPPs at the top and bottom interfaces of the grown epilayer were excited by the prism coupling. A high-index Ge hemispherical prism provides efficient coupling conditions of SPPs on flat surfaces and facilitates acquiring their dispersion diagrams. We observed diffraction into symmetry-prohibited diffraction orders stimulated by the excitation of surface plasmon-polaritons in a periodically structured epilayer. Characterization shows good agreement between the theory and experimental results and confirms that highly doped InP is an effective plasmonic material aiming it for applications in the mid-IR wavelength range.

  2. Multimodal emissions from Tb{sup 3+}/Yb{sup 3+} co-doped lithium borate glass: Upconversion, downshifting and quantum cutting

    Energy Technology Data Exchange (ETDEWEB)

    Bahadur, A.; Yadav, R.S.; Yadav, R.V.; Rai, S.B., E-mail: sbrai49@yahoo.co.in

    2017-02-15

    This paper reports the optical properties of Tb{sup 3+}/Yb{sup 3+} co-doped lithium borate (LB) glass prepared by melt quench method. The absorption spectrum of the Yb{sup 3+} doped LB glass contains intense NIR band centered at 976 nm due to {sup 2}F{sub 7/2}→{sup 2}F{sub 5/2} transition. The emission spectra of the prepared glasses have been monitored on excitation with 266, 355 and 976 nm. The Yb{sup 3+} doped glass emits a broad NIR band centered at 976 nm whereas the Tb{sup 3+} doped glass gives off visible bands on excitations with 266 and 355 nm. When the Tb{sup 3+} and Yb{sup 3+} ions are co-doped together, the emission intensity in the visible region decreases whereas it increases in the NIR region significantly. The increase in the emission intensity in the NIR region is due to efficient cooperative energy transfer (CET) from Tb{sup 3+} to Yb{sup 3+} ions. The quantum cutting efficiency for Tb{sup 3+}/Yb{sup 3+} co-doped glass has been calculated and compared for 266 and 355 nm excitations. The quantum cutting efficiency is larger for 355 nm excitation (137%). The Tb{sup 3+}/Yb{sup 3+} co-doped LB glass also emits upconverted visible bands on excitation with 976 nm. The mechanisms involved in the energy transfer have been discussed using schematic energy level diagram. The Tb{sup 3+}/Yb{sup 3+} co-doped LB glass may be used in the optical devices and in solar cell for solar spectral conversion and behaves as a multi-modal photo-luminescent material. - Graphical abstract: The Tb{sup 3+}/Yb{sup 3+} co-doped lithium borate (LB) glass prepared by melt quench method emits upconverted visible emissions through upconversion CET from Yb{sup 3+} to Tb{sup 3+} ions and quantum cutting emissions through downconversion CET from Tb{sup 3+} to Yb{sup 3+} ions. Therefore, the Tb{sup 3+}/Yb{sup 3+} co-doped LB glass may find applications in optical devices and solar cell and behaves as a multi-modal photo-luminescent material. - Highlights: • The Tb{sup 3+}/Yb{sup 3

  3. Mid-IR optical properties of silicon doped InP

    DEFF Research Database (Denmark)

    Panah, Mohammad Esmail Aryaee; Han, Li; Norrman, Kion

    2017-01-01

    of growth conditions on the optical and electrical properties of silicon doped InP (InP:Si) in the wavelength range from 3 to 40 μm was studied. The carrier concentration of up to 3.9 × 1019 cm-3 is achieved by optimizing the growth conditions. The dielectric function, effective mass of electrons and plasma...

  4. Guided mode gain competition in Yb-doped rod-type photonic crystal fibers

    DEFF Research Database (Denmark)

    Poli, Federica; Passaro, Davide; Cucinotta, Annamaria

    2009-01-01

    The gain competition among the guided modes in Yb-doped rod-type photonic crystal fibers with a low refractive index core is investigated with a spatial model to demonstrate the fiber effective single-mode behaviour.......The gain competition among the guided modes in Yb-doped rod-type photonic crystal fibers with a low refractive index core is investigated with a spatial model to demonstrate the fiber effective single-mode behaviour....

  5. Downconversion in Pr3+–Yb3+ co-doped ZBLA fluoride glasses

    International Nuclear Information System (INIS)

    Maalej, O.; Boulard, B.; Dieudonné, B.; Ferrari, M.; Dammak, M.; Dammak, M.

    2015-01-01

    Fluorozirconate ZBLA glasses with molar composition 57ZrF 4 –34BaF 2 –5LaF 3 –4AlF 3 –0.5PrF 3 –xYbF 3 (from x=0 to 10) were synthesized to evaluate the rate of the conversion of visible photons into infrared photons. The emission spectra in the near infrared (NIR) at 950–1100 nm and the luminescence decays in the visible and NIR indicate an energy transfer from Pr 3+ to Yb 3+ upon blue excitation of Pr 3+ at 440 nm. The energy transfer efficiency increases with Yb 3+ concentration to reach 86% with 0.5Pr 3+ –10Yb 3+ co-doping (in mol%). However, the quenching of the Yb 3+ emission strongly reduces the efficiency of the downconversion process: the decay time values decrease from 600 µs (x=0.5 mol%) to 85 µs (x=10 mol%). - Highlights: • We synthesized 0.5Pr 3+ –xYb 3+ co-doped ZBLA glasses (from x=0 to 10 mol %). • Photoluminescence of Yb 3+ was observed at 980 nm under blue excitation. • Time resolved measurements have been performed in the visible and near infrared. • Energy transfer efficiency from Pr 3+ to Yb 3+ reaches 86% in 0.5 Pr 3+ –10Yb 3+ glass

  6. Photoluminescence study of Sm{sup 3+}–Yb{sup 3+}co-doped tellurite glass embedding silver nanoparticles

    Energy Technology Data Exchange (ETDEWEB)

    Reza Dousti, M., E-mail: mrdousti@ifsc.usp.br [Laboratório de Espectroscopia de Materiais Funcionais (LEMAF), Instituto de Fisica de São Carlos, Universidade de São Paulo, Av. Trabalhador So-carlense 400, São Carlos, SP 13566-590 (Brazil); Department of Physics, Tehran-North Branch, Islamic Azad University Tehran (Iran, Islamic Republic of); Department of Physics, Faculty of Science, Universiti Teknologi Malaysia, Skudai 81310, Johor (Malaysia); Amjad, R.J. [Department of Physics, Faculty of Science, Universiti Teknologi Malaysia, Skudai 81310, Johor (Malaysia); Department of Physics, COMSATS Institute of Information Technology, Lahore 54000 (Pakistan); Hosseinian S, R.; Salehi, M.; Sahar, M.R. [Department of Physics, Faculty of Science, Universiti Teknologi Malaysia, Skudai 81310, Johor (Malaysia)

    2015-03-15

    We report on the upconversion emission of Sm{sup 3+} ions doped tellurite glass in the presence of Yb{sup 3+} ions and silver nanoparticles. The enhancement of infrared-to-visible upconversion emissions is achieved under 980 nm excitation wavelength and attributed to the high absorption cross section of Yb{sup 3+} ions and an efficient energy transfer to Sm{sup 3+} ions. Further enhancements are attributed to the plasmonic effect via metallic nanoparticles resulting in the large localized field around rare earth ions. However, under excitation at 406 nm, the addition of Yb{sup 3+} content and heat-treated silver nanoparticles quench the luminescence of Sm{sup 3+} ions likely due to quantum cutting and plasmonic diluent effects, respectively. - Highlights: • Sm{sup 3+} tellurite glasses co-doped with Yb{sup 3+} ions and tri-doped with Yb{sup 3+}:Ag NPs were prepared. • In first step, Yb{sup 3+} ions enhanced the upconversion emissions of Sm{sup 3+} doped samples. • In second step, Ag NPs further enhanced the upconversion emissions in tri-doped glasses. • Finally, the quench in luminescence under 406 nm excitation is observed and discussed.

  7. Peculiarities of defect formation in InP single crystals doped with donor (S, Ge) and acceptor (Zn) impurities

    International Nuclear Information System (INIS)

    Mikryukova, E.V.; Morozov, A.N.; Berkova, A.V.; Nashel'skij, A.Ya.; Yakobson, S.V.

    1988-01-01

    Peculiarities of dislocation and microdefect formation in InP monocrystals doped with donor (S,Ge) and acceptor (Zn) impurities are investigated by the metallography. Dependence of dislocation density on the concentration of alloying impurity is established. Microdefects leading to the appearance of 5 different types of etch figures are shown to be observed in doped InP monocrystals. The mechanism of microdefect formation is suggested

  8. Resonantly cladding-pumped Yb-free Er-doped LMA fiber laser with record high power and efficiency.

    Science.gov (United States)

    Zhang, Jun; Fromzel, Viktor; Dubinskii, Mark

    2011-03-14

    We report the results of our power scaling experiments with resonantly cladding-pumped Er-doped eye-safe large mode area (LMA) fiber laser. While using commercial off-the-shelf LMA fiber we achieved over 88 W of continuous-wave (CW) single transverse mode power at ~1590 nm while pumping at 1532.5 nm. Maximum observed optical-to-optical efficiency was 69%. This result presents, to the best of our knowledge, the highest power reported from resonantly-pumped Yb-free Er-doped LMA fiber laser, as well as the highest efficiency ever reported for any cladding-pumped Er-doped laser, either Yb-co-doped or Yb-free.

  9. Spectroscopy of Yb-doped tungsten-tellurite glass and assessment of its lasing properties

    Science.gov (United States)

    Merzliakov, M. A.; Kouhar, V. V.; Malashkevich, G. E.; Pestryakov, E. V.

    2018-01-01

    Glasses of the TeO2-WO3-Yb2O3 system are synthesized for wide range of Yb3+ concentrations of up to 6.0 × 1021 ions/cm3. The spectral-luminescent properties of lightly doped samples are investigated at room temperature and at the boiling point of liquid nitrogen. The energies of the Stark levels of the ground and excited states of Yb3+ ions incorporated into tungsten-tellurite glass are determined by analyzing the low-temperature spectra. The absorption, emission, and gain cross section spectra are obtained. The excess of the measured fluorescence decay time over the radiative lifetime ∼0.3 ms derived from the absorption spectra is attributed to the reabsorption effect in bulk samples. Measurements of lightly doped glass powder in the immersion liquid are made to reduce the effect of reabsorption. The fluorescence decay time of the powder is very close to the calculated radiative lifetime. Compared with phosphate, silicate, and other Yb3+-doped glasses, the tungsten-tellurite glass has a promising potential as a gain medium for lasers and amplifiers.

  10. Absorption Spectra Of Rbcl:Yb Rbbr:Yb And Rbi:Yb Crystals ...

    African Journals Online (AJOL)

    Single crystals of rubidium chloride, bromide and iodide were doped with substitutional divalent ytterbium, Yb ions, by heating them in ytterbium atmosphere. The absorption spectra of the Yb doped crystals were measured at room and liquid nitrogen temperatures. The spectra were found to consist of intense broad ...

  11. Effect of sulphur-doping on the formation of deep centers in n-type InP under irradiation

    International Nuclear Information System (INIS)

    Kol'chenko, T.I.; Lomako, V.M.; Moroz, S.E.

    1988-01-01

    Effect of sulfur-doping on the efficiency of electron trap formation in InP under irradiation was studied using deep level capacity nonstationary spectroscopy method (DLCNS). Structures with Schottky barrier based on epitaxial InP films with ∼10μm thickness (n 0 =8x10 14 -6x10 17 cm -3 ) were irradiated with 60 Co γ-quanta at 40 deg C; the particle flux intensity made up ∼10 12 cm -2 xs -1 . Experimental results presented allow one to conclude that InP doping with sulfur up to n 0 =6x10 17 cm -3 in contrast to the case of silicon doping does not produce a notable effect on the electron trap formation efficiency under irradiation. The observed reduction of configuration-bistable M-center introduction rate in samples with n 0 >10 16 cm -3 is explained by the change of filling of E c -0.12 eV level belonging to unknown X defect

  12. Synthesis and thermoelectric properties of rare earth Yb-doped Ba8−xYbxSi30Ga16 clathrates

    International Nuclear Information System (INIS)

    Liu, Lihua; Li, Feng; Wei, Yuping; Chen, Ning; Bi, Shanli; Qiu, Hongmei; Cao, Guohui; Li, Yang

    2014-01-01

    Highlights: • Samples with the chemical formula Ba8− x Yb x Si 30 Ga 16 (x = 0, 0.5, 0.7, 1 and 1.5) were prepared. • Some Yb atoms enter the clathrate lattice to replace Ba, while other Yb atoms are oxidized as Yb 2 O 3 . • The thermal conductivity decreases with Yb-doping. • Thermoelectric figure of merit ZT significantly increased. -- Abstract: The potential thermoelectric and magnetic application of clathrate materials with rare-earth doping is the focus of much of the recent research activity in the synthetic material physics and chemistry. A series of clathrate samples with the chemical formula Ba 8−x Yb x Si 30 Ga 16 (x = 0, 0.5, 0.7, 1 and 1.5) were prepared by combining arc melting, ball milling and spark plasma sintering (SPS) techniques. X-ray diffraction and scanning electronic microscopy combined with energy-dispersive X-ray spectroscopy (EDS) analysis showed the dominant phase to be the type-I clathrate. Whereas, X-ray structural refinement and EDS analysis indicated that some Yb atoms enter the clathrate lattice to replace Ba at 2a sites, while other Yb atoms are oxidized as Yb 2 O 3 precipitated around grain boundaries. The solid solubility of Yb into clathrate lattice yielded x ∼ 0.3. Comparative analysis between Yb-doped and Yb-free clathrates showed that the thermal conductivity decreases with Yb-doping. Consequently, thermoelectric figure of merit ZT significantly increased

  13. Magnetocaloric effect in In doped YbMnO{sub 3}

    Energy Technology Data Exchange (ETDEWEB)

    Sattibabu, Bhumireddi, E-mail: bsb.satti@gmail.com [School of Engineering Sciences and Technology, University of Hyderabad, Hyderabad 500046 (India); Department of Electronics and Physics, Institute of Science, GITAM University, Visakhapatnam 530045 (India); Bhatnagar, A.K., E-mail: anilb42@gmail.com [School of Physics, University of Hyderabad, Hyderabad 500046 (India); Vinod, K.; Mani, Awadhesh [Condensed Matter Physics Division, Materials Science Group, Indira Gandhi Centre for Atomic Research, Kalpakkam 603102 (India)

    2017-06-01

    Magnetic and magnetocaloric (MCE) properties of Yb{sub 0.9}In{sub 0.1}MnO{sub 3} and Yb{sub 0.8}In{sub 0.2}MnO{sub 3} polycrystalline samples are presented in this paper. Isothermal magnetization measurements reveal a field induced magnetic transition. Magnetic entropy change of 2.34±0.35 J/mole-K for Yb{sub 0.9}In{sub 0.1}MnO{sub 3} and 2.64±0.38 J/mole-K for Yb{sub 0.8}In{sub 0.2}MnO{sub 3} field change ΔH =10 KOe is observed around the ferromagnetic ordering temperature of Yb{sup 3+}. Values of relative cooling power for the same field change are found to be 38.03±9 J /mol, and 40.90±10 J/mol for Yb{sub 0.9}In{sub 0.1}MnO{sub 3} and Yb{sub 0.8}In{sub 0.2}MnO{sub 3}, respectively. These values suggest In doped YbMnO{sub 3} may be a potential candidate for magnetic refrigerant at low temperatures.

  14. Synthesis and characterization of Nd3+: Yb3+ co-doped near infrared sensitive fluorapatite nanoparticles as a bioimaging probe

    Science.gov (United States)

    Karthi, S.; Kumar, G. A.; Sardar, D. K.; Santhosh, C.; Girija, E. K.

    2018-03-01

    Trivalent Nd and Yb co-doped rod shaped hexagonal phase fluorapatite (FAP) nanoparticles of length and width about 32 and 13 nm, respectively were prepared by hydrothermal method and investigated the ability for 980 nm emission via Nd3+ → Yb3+ energy transfer with the objective of utilizing them in biomedical imaging. Nd3+ → Yb3+ energy transfer in FAP was studied as a function of both Nd3+ and Yb3+ concentrations and found that when Yb3+ concentration was 10 mol% the FAP phase has partially turned in to YbPO4 phase. The Yb3+ emission intensity at 980 nm significantly increased up to 5 mol% Yb3+ doping and then reduced drastically for further increase in its concentration. Nd3+ →Yb3+ energy transfer rates were evaluated from the decay curves and found that a transfer rate of 71% for 2 mol% Nd3+ co-doped with 5 mol% Yb3+. The cytocompatibility test with fibroblast like cells using MTT assay revealed that the nanoparticles are compatible with the cells.

  15. Thermoluminescence properties of Yb-Tb-doped SiO2 optical fiber subject to 6 and 10 MV photon irradiation

    Science.gov (United States)

    Sahini, M. H.; Wagiran, H.; Hossain, I.; Saeed, M. A.; Ali, H.

    2014-08-01

    This paper reports thermoluminescence characteristics of thermoluminescence dosimetry 100 chips and Yb-Tb-doped optical fibers irradiated with 6 and 10 MV photons. Thermoluminescence response of both dosimeters increases over a wide photon dose range from 0.5 to 4 Gy. Yb-Tb-doped optical fibers demonstrate useful thermoluminescence properties and represent a good candidate for thermoluminescence dosimetry application with ionizing radiation. The results of this fiber have been compared with those of commercially available standard thermoluminescence dosimetry-100 media. Commercially available Yb-Tb-doped optical fibers and said standard media are found to yield a linear relationship between dose- and thermoluminescence signal, although Yb-Tb-doped optical fibers provide only 10 % of the sensitivity of thermoluminescence dosimetry-100. With better thermoluminescence characteristics such as small size (125 μm diameter), high flexibility, easy of handling and low cost, as compared to other thermoluminescence materials, indicate that commercial Yb-Tb-doped optical fiber is a promising thermoluminescence material for variety of applications.

  16. Electronic properties of pure and p-type doped hexagonal sheets and zigzag nanoribbons of InP

    International Nuclear Information System (INIS)

    Longo, R C; Carrete, J; Alemany, M M G; Gallego, L J

    2013-01-01

    Unlike graphene, a hexagonal InP sheet (HInPS) cannot be obtained by mechanical exfoliation from the native bulk InP, which crystallizes in the zinc blende structure under ambient conditions. However, by ab initio density functional theory calculations we found that a slightly buckled HInPS is stable both in pristine form and when doped with Zn atoms; the same occurred for hydrogen-passivated zigzag InP nanoribbons (ZInPNRs), quasi-one-dimensional versions of the quasi-two-dimensional material. We investigated the electronic properties of both nanostructures, in the latter case also in the presence of an external transverse electric field, and the results are compared with those of hypothetical planar HInPS and ZInPNRs. The band gaps of planar ZInPNRs were found to be tunable by the choice of strength of this field, and to show an asymmetric behavior under weak electric fields, by which the gap can either be increased or decreased depending on their direction; however, this effect is absent from slightly buckled ZInPNRs. The binding energies of the acceptor impurity states of Zn-doped HInPS and ZInPNRs were found to be similar and much larger than that of Zn-doped bulk InP. These latter findings show that the reduction of the dimensionality of these materials limits the presence of free carriers. (paper)

  17. Characterizations of Pr-doped Yb3Al5O12 single crystals for scintillator applications

    Science.gov (United States)

    Yoshida, Yasuki; Shinozaki, Kenji; Igashira, Takuya; Kawano, Naoki; Okada, Go; Kawaguchi, Noriaki; Yanagida, Takayuki

    2018-04-01

    Yb3Al5O12 (YbAG) single crystals doped with different concentrations of Pr were synthesized by the Floating Zone (FZ) method. Then, we evaluated their basic optical and scintillation properties. All the samples showed photoluminescence (PL) with two emission bands appeared approximately 300-500 nm and 550-600 nm due to the charge transfer luminescence of Yb3+ and intrinsic luminescence of the garnet structure, respectively. A PL decay profile of each sample was approximated by a sum of two exponential decay functions, and the obtained decay times were 1 ns and 3-4 ns. In the scintillation spectra, we observed emission peaks in the ranges from 300 to 400 nm and from 450 to 550 nm for all the samples. The origins of these emissions were attributed to charge transfer luminescence of Yb3+ and intrinsic luminescence of the garnet structure, respectively. The scintillation decay times became longer with increasing the Pr concentrations. Among the present samples, the 0.1% Pr-doped sample showed the lowest scintillation afterglow level. In addition, pulse height spectrum of 5.5 MeV α-rays was demonstrated using the Pr-doped YbAG, and we confirmed that all the samples showed a full energy deposited peak. Above all, the 0.1% Pr-doped sample showed the highest light yield with a value of 14 ph/MeV under α-rays excitation.

  18. Nondestructive evaluation of differently doped InP wafers by time-resolved four-wave mixing technique

    International Nuclear Information System (INIS)

    Kadys, A.; Sudzius, M.; Jarasiunas, K.; Mao Luhong; Sun Niefeng

    2006-01-01

    Photoelectric properties of semi-insulating, differently doped, and undoped indium phosphide wafers, grown by the liquid encapsulation Czochralski method, have been investigated by time-resolved picosecond four-wave mixing technique. Deep defect related carrier generation, recombination, and transport properties were investigated experimentally by measuring four-wave mixing kinetics and exposure characteristics. The presence of deep donor states in undoped InP was confirmed by a pronounced effect of a space charge electric field to carrier transport. On the other hand, the recharging dynamics of electrically active residual impurities was observed in undoped and Fe-doped InP through the process of efficient trapping of excess carriers. The bipolar diffusion coefficients and mobilities were determined for the all wafers

  19. Color tunable emission through energy transfer from Yb3+ co-doped SrSnO3: Ho3+ perovskite nano-phosphor

    Science.gov (United States)

    Jain, Neha; Singh, Rajan Kr.; Sinha, Shriya; Singh, R. A.; Singh, Jai

    2018-04-01

    First time color tunable lighting observed from Ho3+ and Yb3+ co-doped SrSnO3 perovskite. Down-conversion and up-conversion (UC) photoluminescence emission spectra were recorded to understand the whole mechanism of energy migration between Ho3+ and Yb3+ ions. The intensity of green and red emission varies with Yb3+ doping which causes multicolour emissions from nano-phosphor. The intensity of UC red emission (654 nm) obtained from 1 at.% Ho3+ and 3 at.% Yb3+ co-doped nano-phosphor is nine times higher than from 1 at.% Ho3+ doped SrSnO3 nano-phosphor. Enhanced brightness of 654 nm in UC process belongs in biological transparency window so that it might be a promising phosphor in the bio-medical field. Moreover, for the other Yb3+ co-doped nano-phosphor, Commission Internationale de l'Éclairage chromaticity co-ordinates were found near the white region and their CCT values lie in the range 4900-5100 K indicating cool white. Decay time was measured for 545 nm emission of Ho3+ ion found in 7.652 and 8.734 µs at 355 nm excitation. The variation in lifetime was observed in ascending order with increasing Yb3+ concentration which supports PL emission spectra observation that with increasing Yb3+ concentration, rate of transition has changed. These studies reveal that Ho3+ and Yb3+ co-doped phosphor is useful for fabrication of white LEDs.

  20. Spectroscopic properties of Er3+ and Yb3+ co-doped glass ceramics containing SrF2 nanocrystals

    International Nuclear Information System (INIS)

    Qiao Xvsheng; Fan Xianping; Wang Minquan; Zhang Xianghua

    2009-01-01

    The spectroscopic properties of Er 3+ /Yb 3+ co-doped 50SiO 2 -10Al 2 O 3 -20ZnF 2 -20SrF 2 glass and glass ceramic containing SrF 2 nanocrystals were investigated. The formation of SrF 2 nanocrystals in the glass ceramic was confirmed by XRD. The oscillator strengths for several transitions of the Er 3+ ions in the glass ceramic have been obtained and the Judd-Ofelt parameters were then determined. The XRD result and Judd-Ofelt parameters suggested that Er 3+ and Yb 3+ ions had efficiently enriched in the SrF 2 nanocrystals in the glass ceramic. The lifetime of excited states has been used to reveal the surroundings of luminescent Er 3+ and Yb 3+ and energy transfer (ET) mechanism between Er 3+ and Yb 3+ . Much stronger upconversion luminescence and longer lifetime of the Er 3+ /Yb 3+ co-doped glass ceramic were observed in comparison with the Er 3+ /Yb 3+ co-doped glass, which could be ascribed to more efficient ET from Yb 3+ to Er 3+ due to the enrichment of Yb 3+ and Er 3+ and the shortening of the distance between lanthanide ions in the precipitated SrF 2 nanocrystals.

  1. Highly doped InP as a low loss plasmonic material for mid-IR region

    DEFF Research Database (Denmark)

    Panah, Mohammad Esmail Aryaee; Takayama, Osamu; Morozov, S. V.

    2016-01-01

    by fitting the calculated infrared reflectance spectra to the measured ones. The retrieved permittivity was then used to simulate surface plasmon polaritons (SPPs) propagation on flat and structured surfaces, and the simulation results were verified in direct experiments. SPPs at the top and bottom......We study plasmonic properties of highly doped InP in the mid-infrared (IR) range. InP was grown by metal-organic vapor phase epitaxy (MOVPE) with the growth conditions optimized to achieve high free electron concentrations by doping with silicon. The permittivity of the grown material was found...... interfaces of the grown epilayer were excited by the prism coupling. A high-index Ge hemispherical prism provides efficient coupling conditions of SPPs on flat surfaces and facilitates acquiring their dispersion diagrams. We observed diffraction into symmetry-prohibited diffraction orders stimulated...

  2. Effects of Be doping on InP nanowire growth mechanisms

    Energy Technology Data Exchange (ETDEWEB)

    Yee, R. J.; Gibson, S. J.; LaPierre, R. R. [Department of Engineering Physics, Centre for Emerging Device Technologies, McMaster University, Hamilton, Ontario L8S 4L7 (Canada); Dubrovskii, V. G. [St. Petersburg Academic University, Khlopina 8/3, 194021 St. Petersburg (Russian Federation); Ioffe Physical Technical Institute RAS, Politekhnicheskaya 26, 194021 St. Petersburg (Russian Federation)

    2012-12-24

    Be-doped InP nanowires were grown by the gold-assisted vapour-liquid-solid mechanism in a gas source molecular beam epitaxy system. The InP nanowire length versus diameter [L(D)] dependence revealed an unexpected transition with increasing Be dopant concentration. At Be dopant concentration below {approx}10{sup 18} cm{sup -3}, nanowires exhibited the usual inverse L(D) relationship, indicating a diffusion-limited growth regime. However, as dopant concentration increased, the nanowire growth rate was suppressed for small diameters, resulting in an unusual L(D) dependence that increased before saturating in height at about 400 nm. The cause of this may be a change in the droplet chemical potential, introducing a barrier to island nucleation. We propose a model accounting for the limitations of diffusion length and monolayer nucleation to explain this behaviour.

  3. Nanocrystal in Er3+-doped SiO2-ZrO2 Planar Waveguide with Yb3+ Sensitizer

    International Nuclear Information System (INIS)

    Razaki, N. Iznie; Jais, U. Sarah; Abd-Rahman, M. Kamil; Bhaktha, S. N. B.; Chiasera, A.; Ferrari, M.

    2010-01-01

    Higher doping of Er 3+ in glass ceramic waveguides would cause concentration and pair-induced quenching which lead to inhomogeneous line-width of luminescence spectrum thus reduce output intensity. Concentration quenching can be overcome by introducing ZrO 2 in the glass matrix while co-doping with Yb 3+ which acts as sensitizer would improve the excitation efficiency of Er 3+ . In this study, SiO 2 -ZrO 2 planar waveguides having composition in mol percent of 70SiO 2 -30ZrO 2 doped with Er 3+ and co-doped with Yb 3+ , were prepared via sol-gel route. Narrower and shaper peaks of PL and XRD shows the formation of nanocrystals. Intensity is increase with addition amount of Yb 3+ shows sensitizing effect on Er 3+ .

  4. Down-conversion luminescence from (Ce, Yb) co-doped oxygen-rich silicon oxides

    International Nuclear Information System (INIS)

    Heng, C. L.; Wang, T.; Su, W. Y.; Wu, H. C.; Yin, P. G.; Finstad, T. G.

    2016-01-01

    We have studied down-conversion photoluminescence (PL) from (Ce, Yb) co-doped “oxygen rich” silicon oxide films prepared by sputtering and annealing. The Ce"3"+ ∼510 nm PL is sensitive to the Ce concentration of the films and is much stronger for 3 at. % Ce than for 2 at. % Ce after annealing at 1200 °C. The PL emission and excitation spectroscopy results indicate that the excitation of Yb"3"+ is mainly through an energy transfer from Ce"3"+ to Yb"3"+, oxide defects also play a role in the excitation of Yb"3"+ after lower temperature (∼800 °C) annealing. The Ce"3"+ 510 nm photon excites mostly only one Yb"3"+ 980 nm photon. Temperature-dependent PL measurements suggest that the energy transfer from Ce"3"+ to Yb"3"+ is partly thermally activated.

  5. Density-functional study on the robust ferromagnetism in rare-earth element Yb-doped SnO{sub 2}

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Kai-Cheng, E-mail: kczhang@yeah.net [College of Mathematics and Physics, Bohai University, Jinzhou 121013 (China); Li, Yong-Feng [Key Laboratory of Integrated Exploitation of Bayan Obo Multi-Metal ResourcesInner Mongolia University of Science and Technology, Baotou 014010 (China); School of Mathematics, Physics and Biological Engineering, Inner Mongolia University of Science and Technology, Baotou 014010 (China); Liu, Yong [State Key Laboratory of Metastable Materials Science and Technology and College of Science, Yanshan University, Qinhuangdao, Hebei 066004 (China); Chi, Feng [College of Engineering, Bohai University, Jinzhou 121013 (China)

    2014-06-01

    So far, little has been known about the ferromagnetism induced by p–f hybridization. We investigate the magnetic properties of Yb-doped SnO{sub 2} by first-principles calculations. We find that the doped system favors the ferromagnetic state and a room-temperature ferromagnetism can be expected in it. The origin of ferromagnetism can be attributed to the p–f hybridization between Yb impurity and its surrounding oxygen atoms. The formation energy of defect complex is calculated and the magnetic mediation of intrinsic vacancies is studied. Our results reveal that the formation energy of the defect complex with Sn vacancy is about 7.3 eV lower in energy than that with oxygen vacancy. This means Sn vacancy is much easier to form than oxygen vacancy in the presence of Yb substitution. The ferromagnetism of the doped system is greatly enhanced in the presence of Sn vacancies. - Highlights: • Room-temperature ferromagnetism can be expected in Yb-doped SnO{sub 2}. • The origin of ferromagnetism can be attributed to the p–f hybridization between Yb and O atoms. • Oxygen vacancies are much hard to form and contribute little to the ferromagnetism. • Sn vacancies are easy to form under oxygen-rich condition and stabilize the ferromagnetism effectively.

  6. Filament-induced luminescence and supercontinuum generation in undoped, Yb-doped, and Nd-doped YAG crystals

    Science.gov (United States)

    Kudarauskas, D.; Tamošauskas, G.; Vengris, M.; Dubietis, A.

    2018-01-01

    We present a comparative spectral study of filament-induced luminescence and supercontinuum generation in undoped, Yb-doped, and Nd-doped YAG crystals. We show that supercontinuum spectra generated by femtosecond filamentation in undoped and doped YAG crystals are essentially identical in terms of spectral extent. On the other hand, undoped and doped YAG crystals exhibit remarkably different filament-induced luminescence spectra whose qualitative features are independent of the excitation wavelength and provide information on the energy deposition to embedded dopants, impurities, and the crystal lattice itself. Our findings suggest that filament-induced luminescence may serve as a simple and non-destructive tool for spectroscopic studies in various transparent dielectric media.

  7. Crystal growth, optical properties, and laser operation of Yb3+-doped NYW single crystal

    Science.gov (United States)

    Cheng, Y.; Xu, X. D.; Yang, X. B.; Xin, Z.; Cao, D. H.; Xu, J.

    2009-11-01

    Laser crystal Yb3+-doped NaY(WO4)2 (Yb:NYW) with excellent quality has been grown by Czochralski technique. The rocking curves from (400) plane of as-grown Yb:NYW crystal was measured and the full-width value at half-maximum was 19.92″. The effective segregation coefficients were measured by the X-ray fluorescence method. The polarized absorption spectra and the fluorescence spectra of Yb:NYW crystal were measured at room temperature. The fluorescence decay lifetime of Yb3+ ion in NYW crystal has been investigated. The spectroscopic parameters of Yb:NYW crystal are calculated and compared with those of Yb:YAG crystal. A continuous wave output power of 3.06 W at 1031 nm was obtained with a slope efficiency of 42% by use of diode pumping.

  8. Development and applications of femtosecond monolithic Yb-doped fiber chirped-pulse amplifiers

    International Nuclear Information System (INIS)

    Zhu, L.

    2011-01-01

    In the past few years, compact and environmentally stable high-energy ultrashort pulse laser sources have been broadly utilized in many different applications. Fiber lasers offer big practical advantages over bulk solid-state laser systems in terms of flexibility, compactness, reliability, cost effectiveness and turn-key operability. Moreover, thermal effects are dramatically reduced due to the large surface-to-volume ratio of an optical fiber, and good spatial mode quality can be ensured by its waveguiding property. Therefore, a fiber-based laser system is considered to be the preferred laser architecture. The main theme of this thesis is the development of various femtosecond monolithic Yb-doped fiber chirped-pulse-amplification (FCPA) system and their applications. We demonstrate an ultrafast high-energy monolithic Yb-doped FCPA system in which the pulse fidelity is preserved by weakening the nonlinear effects via a substantial level of temporal stretching of the seed pulses and by using highly doped active fibers as amplifying media. The presented monolithic FCPA delivers up to ∼ 25 μJ diffraction-limited pulses that can be recompressed to sub-200 fs duration, and the pulse quality has been confirmed through the second-harmonic-generation (SHG) conversion efficiency of over 52%. Improved dispersion and nonlinearity management schemes of the FCPA system allowing substantial pulse energy scaling in the monolithic format as well as methods for overcoming a series of technological challenges are reported. Three different types of Yb-doped fiber oscillators have been developed and built in the course of this PhD work. First, we compare two oscillator types that are based on the all-normal-dispersion (ANDi) regime and the dispersion-managed (DM) regime. Both of them have been tested as the seed-pulse source of the monolithic Yb-doped FCPA system. Then we introduce another novel design based on higher-order-mode (HOM) dispersion management that competes with a

  9. Upconversion dynamics in Yb3+-Ho3+-doped fluoroindate glasses

    International Nuclear Information System (INIS)

    Martin, I.R.; Rodriguez, V.D.; Lavin, V.; Rodriguez-Mendoza, U.R.

    1998-01-01

    The mechanisms and dynamics of the upconversion emissions in Yb 3+ -Ho 3+ -doped fluoroindate glasses by exciting at 975 nm have been analysed. The upconversion efficiencies have been measured as a function of temperature in the range from 12 to 295 K. The temporal evolution of the 545- and 650-nm upconversion emissions obtained under flash excitation at 975 nm in codoped samples with 2.25 mol.% of Yb 3+ and 0.75 mol.% of Ho 3+ cannot be described using the energy migration model. This indicates that at this concentration of Yb 3+ the rapid migration regimen between these ions has not been reached. A model is proposed in order to explain the temporal evolution of these emissions taking into account energy migration between donors and backtransfer processes. (orig.)

  10. All-fiber Yb-doped fiber laser passively mode-locking by monolayer MoS2 saturable absorber

    Science.gov (United States)

    Zhang, Yue; Zhu, Jianqi; Li, Pingxue; Wang, Xiaoxiao; Yu, Hua; Xiao, Kun; Li, Chunyong; Zhang, Guangyu

    2018-04-01

    We report on an all-fiber passively mode-locked ytterbium-doped (Yb-doped) fiber laser with monolayer molybdenum disulfide (ML-MoS2) saturable absorber (SA) by three-temperature zone chemical vapor deposition (CVD) method. The modulation depth, saturation fluence, and non-saturable loss of this ML-MoS2 are measured to be 3.6%, 204.8 μJ/cm2 and 6.3%, respectively. Based on this ML-MoS2SA, a passively mode-locked Yb-doped fiber laser has been achieved at 979 nm with pulse duration of 13 ps and repetition rate of 16.51 MHz. A mode-locked fiber laser at 1037 nm is also realized with a pulse duration of 475 ps and repetition rate of 26.5 MHz. To the best of our knowledge, this is the first report that the ML-MoS2 SA is used in an all-fiber Yb-doped mode-locked fiber laser at 980 nm. Our work further points the excellent saturable absorption ability of ML-MoS2 in ultrafast photonic applications.

  11. Co-operative energy transfer in Yb3+-Er3+ co-doped SrGdxOy upconverting phosphor

    Science.gov (United States)

    Kumar, Ashwini; Pathak, Trilok K.; Dhoble, S. J.; . Terblans, J. J.; Swart, H. C.

    2018-04-01

    Upconversion nanoparticles (UCNPs) have shown considerable interest in many fields; however, low upconversion efficiency of UCNPs is still the most severe limitation of their applications. Yb3+ and Er3+ co-doped SrGd4O7/Gd2O3(SGO) upconversion (UC) phosphors were synthesized by a modified co-precipitation process. The UC properties were investigated by direct excitation with a 980 nm laser. It was observed that the as prepared materials showed relatively strong green emission, while upon the incorporation of the Er3+ ion, there was an increase in the upconversion luminescence intensity for the red component. The effect of different doping concentration of Er3+on the emission spectra and X-ray diffraction patterns of the UC materials have also been studied. The luminescence lifetimes and Commission Internationale de L'Eclairage coordinates for these as prepared samples were determined to understand the energy transfer (ET) mechanisms occurring between Yb3+ and Er3+ in the SGO host matrix. The UC luminescence intensity as a function of laser pump power was monitored and it was confirmed that the UC process in SGO:Yb3+/Er3+is a two-photon absorption process. The findings reported here are expected to provide a better approach for understanding of the ET mechanisms in the oxide based Yb3+/Er3+ co-doped UC phosphors. This study might be helpful in precisely defined applications where optical transitions are essential criterion and this can be easily achieved by smart tuning of the emission properties of Yb3+/Er3+ co-doped UC phosphors.

  12. Analysis of structure origin and luminescence properties of Yb(3+)-Er(3+) co-doped fluorophosphate glass.

    Science.gov (United States)

    Chen, Fangze; Jing, Xufeng; Wei, Tao; Wang, Fengchao; Tian, Ying; Xu, Shiqing

    2014-08-14

    The near infrared luminescence properties of Yb(3+)-Er(3+) co-doped fluorophosphate glasses have been investigated. The various effects on structure and 1.53 μm emission were analyzed as a function of Yb(3+) concentration. The energy transfer mechanism was proposed. High measured lifetime (10.75 ms), large effective full widths at half maximum (73.71 nm) and large gain per unit length (62.8 × 10(-)(24)cm(2)s) have been achieved in prepared glass. The present glass co-doped with 6mol% YbF3 and 2 mol% ErF3 showed magnificent luminescence properties for telecommunication application. Copyright © 2014 Elsevier B.V. All rights reserved.

  13. Single-mode amplification in Yb-doped rod-type photonic crystal fibers for high brilliance lasers

    DEFF Research Database (Denmark)

    Poli, F.; Lægsgaard, Jesper; Passaro, D.

    2009-01-01

    This paper presents the effect of a low refractive index ring in the Yb-doped rod-type photonic crystal fibre core on the guided mode propagation and analyzed through a spatial and spectral amplifier model. The ring provides a higher differential overlap between the fundamental mode (FM...... to identify a proper ring characteristic that is width, position and refractive index. Then rod-type PCF designs have been optimized with a full-vector modal solver based on the finite-element method. Then, the amplification properties of the Yb-doped rod-type PCFs have been investigated by assuming a forward...

  14. Modeling of Yb3+-sensitized Er3+-doped silica waveguide amplifiers

    DEFF Research Database (Denmark)

    Lester, Christian; Bjarklev, Anders Overgaard; Rasmussen, Thomas

    1995-01-01

    A model for Yb3+-sensitized Er3+-doped silica waveguide amplifiers is described and numerically investigated in the small-signal regime. The amplified spontaneous emission in the ytterbium-band and the quenching process between excited erbium ions are included in the model. For pump wavelengths...

  15. Evolution of magnetic properties and exchange interactions in Ru doped YbCrO3

    International Nuclear Information System (INIS)

    Dalal, Biswajit; Sarkar, Babusona; De, S K; Dev Ashok, Vishal

    2016-01-01

    Magnetic properties of YbCr 1−x Ru x O 3 as a function of temperature and magnetic field have been investigated to explore the intriguing magnetic phenomena in rare-earth orthochromites. A quantitative analysis of x-ray photoelectron spectroscopy confirms the mixed valence state (Yb 3+  and Yb 2+ ) of Yb ions for the highest doped sample. Field-cooled magnetization reveals a broad peak around 75 K and then becomes zero at about 20–24 K, due to the antiparallel coupling between Cr 3+ and Yb 3+ moments. An increase of the Ru 4+ ion concentration leads to a slight increase of compensation temperature T comp from 20 to 24 K, but the Néel temperature remains constant. A larger value of the magnetic moment of Yb ions gives rise to negative magnetization at low temperature. An external magnetic field significantly modifies the temperature dependent magnetization. Simulation of temperature dependent magnetization data, below T N , based on the three (two) magnetic sub-lattice model predicts stronger intra-sublattice exchange interaction than that of inter-sublattice. Thermal hysteresis and Arrot plots suggest first order magnetic phase transition. Random substitution of Ru 4+ ion reduces the magnetic relaxation time. Weak ferromagnetic component in canted antiferromagnetic system and negative internal magnetic field cause zero-field-cooled exchange bias effect. Large magnetocrystalline anisotropy associated with Ru creates high coercivity in the Ru doped sample. A maximum value of magnetocaloric effect is found around the antiferromagnetic ordering of Yb 3+ ions. Antiferromagnetic transition at about 120 K and temperature induced magnetization reversal lead to normal and inverse magnetocaloric effects in the same material. (paper)

  16. Tunable multicolor and white-light upconversion luminescence in Yb3+/Tm3+/Ho3+ tri-doped NaYF4 micro-crystals.

    Science.gov (United States)

    Lin, Hao; Xu, Dekang; Teng, Dongdong; Yang, Shenghong; Zhang, Yueli

    2015-09-01

    NaYF4 micro-crystals with various concentrations of Yb(3+) /Tm(3+) /Ho(3+) were prepared successfully via a simple and reproducible hydrothermal route using EDTA as the chelating agent. Their phase structure and surface morphology were studied using powder X-ray diffraction (XRD) and scanning electron microscopy (SEM). The XRD patterns revealed that all the samples were pure hexagonal phase NaYF4. SEM images showed that Yb(3+)/Tm(3+)/Ho(3+) tri-doped NaYF4 were hexagonal micro-prisms. Upconversion photoluminescence spectra of Yb(3+)/Tm(3+)/Ho(3+) tri-doped NaYF4 micro-crystals with various dopant concentrations under 980 nm excitation with a 665 mW pump power were studied. Tunable multicolor (purple, purplish blue, yellowish green, green) and white light were achieved by simply adjusting the Ho(3+) concentration in 20%Yb(3+)/1%Tm(3+)/xHo(3+) tri-doped NaYF4 micro-crystals. Furthermore, white-light emissions could be obtained using different pump powers in 20%Yb(3+)/1%Tm(3+)/1%Ho(3+) tri-doped NaYF4 micro-crystals at 980 nm excitation. The pump power-dependent intensity relationship was studied and relevant energy transfer processes were discussed in detail. The results suggest that Yb(3+)/Tm(3+) Ho(3+) tri-doped NaYF4 micro-crystals have potential applications in optoelectronic devices such as photovoltaic, plasma display panel and white-light-emitting diodes. Copyright © 2014 John Wiley & Sons, Ltd.

  17. High-power Yb-doped continuous-wave and pulsed fibre lasers

    Indian Academy of Sciences (India)

    2014-01-05

    Jan 5, 2014 ... In this article, a review of Yb-doped CW and pulsed fibre lasers along with our study on self-pulsing dynamics in CW fibre lasers to find its role in high-power fibre laser development and the physical ... Solid State Laser Division, Raja Ramanna Centre for Advanced Technology, Indore 452 013, India ...

  18. Luminescence properties of Y2O3:Bi3+, Yb3+ co-doped phosphor for application in solar cells

    Science.gov (United States)

    Lee, E.; Kroon, R. E.; Terblans, J. J.; Swart, H. C.

    2018-04-01

    Bismuth (Bi3+) and ytterbium (Yb3+) co-doped yttrium oxide (Y2O3) phosphor powder was successfully synthesised using the co-precipitation technique. The X-ray diffraction (XRD) patterns confirmed that a single phase cubic structure with a Ia-3 space group was formed. The visible emission confirmed the two symmetry sites, C2 and S6, found in the Y2O3 host material and revealed that Bi3+ ions preferred the S6 site as seen the stronger emission intensity. The near-infrared (NIR) emission of Yb3+ increased significantly by the presence of the Bi3+ ions when compared to the singly doped Y2O3:Yb3+ phosphor with the same Yb3+ concentration. An increase in the NIR emission intensity was also observed by simply increasing the Yb3+ concentration in the Y2O3:Bi3+, Yb3+ phosphor material where the intensity increased up to x = 5.0 mol% of Yb3+ before decreasing due to concentration quenching.

  19. Near-infrared quantum cutting in Yb3+ ion doped strontium vanadate

    Science.gov (United States)

    Sawala, N. S.; Bajaj, N. S.; Omanwar, S. K.

    2016-05-01

    The materials Sr3-x(VO4)2:xYb were successfully synthesized by co-precipitation method varying the concentration of Yb3+ ions from 0 to 0.06 mol. It was characterize by powder X-ray powder diffraction (XRD) and surface morphology was studied by scanning electronic microscope (SEM). The photoluminescence (PL) properties were studied by spectrophotometers in near infra red (NIR) and ultra violet visible (UV-VIS) region. The Yb3+ ion doped tristrontium vanadate (Sr3(VO4)2) phosphors that can convert a photon of UV region (349 nm) into photons of NIR region (978, 996 and 1026 nm). Hence this phosphor could be used as a quantum cutting (QC) luminescent convertor in front of crystalline silicon solar cell (c-Si) panels to reduce thermalization loss due to spectral mismatch of the solar cells. The theoretical value of quantum efficiency (QE) was calculated from steady time decay measurement and the maximum efficiency approached up to 144.43%. The Sr(3-x) (VO4)2:xYb can be potentiality used for betterment of photovoltaic (PV) technology.

  20. Up-conversion mechanisms in Er{sup 3+} doped YbAG crystals

    Energy Technology Data Exchange (ETDEWEB)

    Kaczkan, Marcin; Borowska, Maja [Institute of Microelectronics and Optoelectronics PW, Warsaw (Poland); Malinowski, Michal [Institute of Microelectronics and Optoelectronics PW, Warsaw (Poland); Institute of Electronic Materials Technology, Warsaw (Poland); Lukasiewicz, Tadeusz; Kolodziejak, Katarzyna [Institute of Electronic Materials Technology, Warsaw (Poland)

    2009-07-15

    Up-conversion phenomena leading to the red, green and violet emissions in erbium doped ytterbium-aluminum garnet (YbAG) are investigated. Absorption and emission spectra and luminescence dynamics from various excited states of YbAG:Er{sup 3+} were registered. The low temperature absorption spectra were used to determine Stark levels energies of Er{sup 3+} ion in the investigated host. Emissions from the high lying excited states {sup 2}G{sub 9/2}, {sup 4}S{sub 3/2} and {sup 4}F{sub 9/2} of Er{sup 3+} were characterized under pulsed multi-photon IR excitation in the region of wavelength corresponding to the strong {sup 2}F{sub 7/2} {yields} {sup 2}F{sub 5/2} absorption transition of Yb{sup 3+} ions. Using the rate equations formalism the dynamics of the observed emissions were modeled. From the comparison of the measured and calculated decays the energy transfer rates between Yb{sup 3+} and Er{sup 3+} ions were evaluated. (copyright 2009 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

  1. Effect of Structural Stress on the Laser Quality of Highly Doped Yb:KY(WO4)2/KY(WO4)2 and Yb:KLu(WO4)2/KLu(WO4)2 Epitaxial Structures

    International Nuclear Information System (INIS)

    Carvajal, J.; Raghothamachar, B.; Silvestre, O.; Chen, H.; Pujol, M.; Petrov, V.; Dudley, M.; Aguilo, M.; Diaz, F.

    2009-01-01

    In this communication we demonstrate how the difference in laser performance of two highly doped (20 at %) epitaxial layers of Yb-doped KY(WO4)2 (KYW) grown on a KYW substrate and Yb-doped KLu(WO4)2 (KLuW) grown on a KLuW substrate, respectively, is related to the presence of structural stress in the epilayers, investigated by synchrotron white beam X-ray topography. From the results obtained, it is clear that the samples that show a larger amount of structural stress, Yb:KYW/KYW epitaxies, lead to lower efficiency in laser operation, giving a direct correlation between the existence and magnitude of such structural stress and the loss in efficiency of laser performance in such epitaxial layers which, from a spectroscopical point of view, are otherwise equivalent.

  2. High-efficiency, deep-junction, epitaxial InP solar cells on (100) and (111)B InP substrates

    Science.gov (United States)

    Venkatasubramanian, R.; Timmons, M. L.; Hutchby, J. A.; Walters, Robert J.; Summers, Geoffrey P.

    1994-01-01

    We report on the development and performance of deep-junction (approximately 0.25 micron), graded-emitter-doped, n(sup +)-p InP solar cells grown by metallorganic chemical vapor deposition (MOCVD). A novel, diffusion-transport process for obtaining lightly-doped p-type base regions of the solar cell is described. The I-V data and external quantum-efficiency response of these cells are presented. The best active-area AMO efficiency for these deep-junction cells on (100)-oriented InP substrates is 16.8 percent, with a J(sub SC) of 31.8 mA/sq cm, a V(sub OC) of 0.843 V, and a fill-factor of 0.85. By comparison, the best cell efficiency on the (111)B-oriented InP substrates was 15.0 percent. These efficiency values for deep-junction cells are encouraging and compare favorably with performance of thin-emitter (0.03 micron) epitaxial cells as well as that of deep-emitter diffused cells. The cell performance and breakdown voltage characteristics of a batch of 20 cells on each of the orientations are presented, indicating the superior breakdown voltage properties and other characteristics of InP cells on the (111)B orientation. Spectral response, dark I-V data, and photoluminescence (PL) measurements on the InP cells are presented with an analysis on the variation in J(sub SC) and V(sub OC) of the cells. It is observed, under open-circuit conditions, that lower-V(sub OC) cells exhibit higher band-edge PL intensity for both the (100) and (111)B orientations. This anomalous behavior suggests that radiative recombination in the heavily-doped n(sup +)-InP emitter may be detrimental to achieving higher V(sub OC) in n(sup +)-p InP solar cells.

  3. White phosphor using Yb3+-sensitized Er3+-and Tm3+-doped sol-gel derived lead-fluorosilicate transparent glass ceramic excited at 980 nm

    Science.gov (United States)

    Tavares, M. C. P.; da Costa, E. B.; Bueno, L. A.; Gouveia-Neto, A. S.

    2018-01-01

    Generation of primary colors and white light through frequency upconversion using sol-gel derived 80SiO2:20PbF2 vitroceramic phosphors doped with Er3+, Er3+/Yb3+, Tm3+/Yb3+, and Er3+/Tm3+/Yb3+ excited at 980 nm is demonstrated. For Er3+ and Er3+/Yb3+ doped samples emissions were obtained in the blue (410 nm), green (530, and 550 nm) and red (670 nm) regions, corresponding to the 2H9/2 → 4I15/2,2H11/2 → 4I15/2, 4S3/2 → 4I152 and 4F9/2 → 4I15/2 transitions of Er3+, respectively. The codoping with Yb3+ ions altered the spectral profile of most of the emissions compared to the single doped samples, resulting in changes in the emitted color, in addition to a significant increase in the emission intensity. In Tm3+/Yb3+ co-doped samples visible emissions in the blue (480 nm), and red (650 nm), corresponding to transitions 1G4 → 3H6 and 1G4 → 3F4 of Tm3+, respectively, were obtained. The emission intensity around 480 nm overcome the red emission, and luminescence showed a predominantly blue tone. White light with CIE-1931 coordinates (0.36; 0.34) was produced by homogeneously mixing up powders of heat treated at 400 °C co-doped samples 5.0Er3+/5.0Yb3+ and 0.5Tm3+/2.5Yb3+ in the mass ratio of 13%, and 87%, respectively. The measured emission spectrum for a sample resulting from the mixture showed a profile with very good agreement with the spectrum found from the superimposition of the spectra of the co-doped samples.

  4. Controllable synthesis and crystal structure determined upconversion luminescence properties of Tm{sup 3+} (Er{sup 3+}) ions doped YbF{sub 3} and NaYbF{sub 4} crystals

    Energy Technology Data Exchange (ETDEWEB)

    Jiang, Tao [Institute of Photonics, Faculty of Science, Ningbo University, Ningbo 315211 (China); Qin, Weiping, E-mail: wpqin@jlu.edu.cn [State Key Laboratory on Integrated Optoelectronics, College of Electronic Science and Engineering, Jilin University, Changchun 130012 (China); Zhou, Jun [Institute of Photonics, Faculty of Science, Ningbo University, Ningbo 315211 (China)

    2014-04-01

    Graphical abstract: - Highlights: • The synthesis of YbF{sub 3} and NaYbF{sub 4} crystals was successfully fulfilled by hydrothermal method. • The phase and morphology of products were adjusted by changing the hydrothermal conditions. • Relatively enhanced ultraviolet upconversion emissions were observed in YbF{sub 3} nanocrystals. • The crystalline phase impact on the upconversion luminescence was systematically studied. - Abstract: The synthesis of YbF{sub 3} and NaYbF{sub 4} crystals was successfully fulfilled by a facial hydrothermal method. The phase and morphology of the products were adjusted by changing the surfactant additive and fluorine source and tuning the pH value of the initial solution. The products with various morphologies range from octahedral nanoparticles, corn-like nanobundles, nanospheres, microrods, and hollow microprisms were prepared at different conditions. The growth mechanism of these products has been systematically studied. Impressively, relatively enhanced high order ultraviolet (UV) upconversion (UC) luminescence was observed in Tm{sup 3+} (Er{sup 3+}) ions doped YbF{sub 3} nanocrystals (NCs) compared with NaYbF{sub 4} microcrystals under the excitation of 980 nm infrared laser. The investigation results reveal that the crystal symmetry of matrix has significant effect on the spectra and lifetimes of the doping lanthanide ions. The simply synthesized water soluble YbF{sub 3} NCs with efficient UV UC luminescence may find potential application in biochemistry.

  5. Enhancing photovoltaic performance of dye-sensitized solar cell by rare-earth doped oxide of Lu2O3:(Tm3+, Yb3+)

    International Nuclear Information System (INIS)

    Li Qingbei; Lin Jianming; Wu Jihuai; Lan Zhang; Wang Yue; Peng Fuguo; Huang Miaoliang

    2011-01-01

    Highlights: → Tm 3+ /Yb 3+ codoped oxide is introduced into the TiO 2 film in dye-sensitized solar cell. → The RE improves light harvest via conversion luminescence and increases photocurrent. → The RE elevates the oxide film energy level and increases the cell photovoltage. → The cell efficiency is increased by 11.1% compared to the cell lacking of RE doping. - Abstract: In order to increase of the photocurrent, photovoltage and energy conversion efficiency of dye-sensitized solar cell (DSSC), rare-earth doped oxide of Lu 2 O 3 :(Tm 3+ , Yb 3+ ) is prepared and introduced into the TiO 2 film in the DSSC. As a luminescence medium, Lu 2 O 3 :(Tm 3+ , Yb 3+ ) improves incident light harvest via a conversion luminescence process and increases photocurrent; as a p-type dopant, the rare-earth ions elevate the energy level of the oxide film and increase the photovoltage. Under a simulated solar light irradiation of 100 mW cm -2 , the light-to-electric energy conversion efficiency of the DSSC with Lu 2 O 3 :(Tm 3+ , Yb 3+ ) doping reaches 6.63%, which is increased by 11.1% compared to the DSSC without Lu 2 O 3 :(Tm 3+ , Yb 3+ ) doping.

  6. Theoretical modelling of dual-wavelength pumped Yb3+–Tm3+ co-doped silica fibre laser

    International Nuclear Information System (INIS)

    Fu, Yuqing; Chen, Jianguo

    2010-01-01

    Numerical simulations have, for the first time to our knowledge, been carried out to characterize the Yb 3+ –Tm 3+ co-doped silica fibre laser (YTFL), defined by a fibre grating and an end mirror, by using the rate equations, which take into consideration both the energy transfer processes from Yb 3+ to Tm 3+ ions and the cross-relaxation processes among different Tm 3+ ions. A dual-wavelength pumping scheme with one at 805 nm and the other at 975 nm is used to pump the YTFL. We have investigated the wavelength-dependent output power of the YTFL, from 1750 to 2200 nm, which takes its maximum output power at ∼ 1800 nm. The effect of the cross-relaxation processes in the Tm 3+ -doped silica fibre laser has been studied. The results indicate that these processes are beneficial to the laser and should be considered in the theoretical modelling. The influence of the Yb 3+ concentration on the characteristics of the YTFL has also been analysed and the results show that Yb 3+ dopants can improve the output power and slope efficiency of the laser

  7. Enhanced frequency upconversion study in Er3+/Yb3+ doped/codoped TWTi glasses

    Science.gov (United States)

    Azam, Mohd; Rai, Vineet Kumar

    2018-04-01

    Er3+/Yb3+ doped/codoped TeO2-WO3-TiO2 (TWTi) glasses have been prepared by using the melt-quenching technique. The upconversion (UC) emission spectra of the developed glasses have been recorded upon 980 nm laser excitation. Three intense UC emission bands have been observed within the green and red region centered at ˜532 nm, ˜553 nm and ˜669 nm corresponding to the 2H11/2→4I15/2, 4S3/2→4I15/2 and 4F9/2→4I15/2 transitions respectively in the singly Er3+ doped glass. On introducing Yb3+ ions in the singly Er3+ doped glass, an enhancement of about ˜ 12 times and ˜50 times in the green and red bands respectively have been observed even at low pump power ˜ 364 mW followed by two photon absorption process. Colour tunability from yellowish green to pure green colour region has been observed on varying the pump power. The prepared glass can be used to produce NIR to green upconverter and colour tunable display devices.

  8. Structure-Dependent Spectroscopic Properties of Yb3+-Doped Phosphosilicate Glasses Modified by SiO₂.

    Science.gov (United States)

    Wang, Ling; Zeng, Huidan; Yang, Bin; Ye, Feng; Chen, Jianding; Chen, Guorong; Smith, Andew T; Sun, Luyi

    2017-02-28

    Yb 3+ -doped phosphate glasses containing different amounts of SiO₂ were successfully synthesized by the conventional melt-quenching method. The influence mechanism of SiO₂ on the structural and spectroscopic properties was investigated systematically using the micro-Raman technique. It was worth noting that the glass with 26.7 mol % SiO₂ possessed the longest fluorescence lifetime (1.51 ms), the highest gain coefficient (1.10 ms·pm²), the maximum Stark splitting manifold of ²F 7/2 level (781 cm -1 ), and the largest scalar crystal-field N J and Yb 3+ asymmetry degree. Micro-Raman spectra revealed that introducing SiO₂ promoted the formation of P=O linkages, but broke the P=O linkages when the SiO₂ content was greater than 26.7 mol %. Based on the previous 29 Si MAS NMR experimental results, these findings further demonstrated that the formation of [SiO₆] may significantly affect the formation of P=O linkages, and thus influences the spectroscopic properties of the glass. These results indicate that phosphosilicate glasses may have potential applications as a Yb 3+ -doped gain medium for solid-state lasers and optical fiber amplifiers.

  9. Investigation of upconversion luminescence in antimony–germanate double-clad two cores optical fiber co-doped with Yb{sup 3+}/Tm{sup 3+} and Yb{sup 3+}/Ho{sup 3+} ions

    Energy Technology Data Exchange (ETDEWEB)

    Zmojda, J.; Kochanowicz, M.; Miluski, P.; Dorosz, J. [Bialystok University of Technology, Wiejska 45 Street, 15-351 Bialystok (Poland); Pisarska, J.; Pisarski, W.A. [Institute of Chemistry, University of Silesia, Szkolna 9, 40-007 Katowice (Poland); Dorosz, D., E-mail: d.dorosz@pb.edu.pl [Bialystok University of Technology, Wiejska 45 Street, 15-351 Bialystok (Poland)

    2016-02-15

    In the paper double-clad optical fiber with two off-set cores co-doped with 1Yb{sub 2}O{sub 3}–0.1Tm{sub 2}O{sub 3} and 1Yb{sub 2}O{sub 3}–0.5Ho{sub 2}O{sub 3} has been investigated. Antimony–germanate glass was melted as a matrix for active cores. The concentration of lanthanides and their ratio have been optimized to achieve maximum upconversion emission intensity at 478 nm ({sup 1}G{sub 4}→{sup 3}H{sub 6}) and 650 nm ({sup 1}G{sub 4}→{sup 3}F{sub 4}) in glasses doped with Tm{sup 3+} ions and 545 nm and 655 nm, corresponding to the {sup 5}F{sub 5}→{sup 5}I{sub 8} and {sup 5}F{sub 4}→{sup 5}I{sub 8} transitions in holmium ions. The energy transfer efficiency in glasses used as optical fiber cores was η{sub Tm}=56% (0.1 mol% Tm{sub 2}O{sub 3}) and η{sub Ho}=85% (0.5 mol% Ho{sub 2}O{sub 3}), respectively. As a result of excitation of the fabricated optical fiber (λ{sub exc}=976 nm), a UC luminescence spectra was obtained. Superposition of three emission bands at the wavelengths of 481 nm (Tm{sup 3+}: blue), 545 nm (Ho{sup 3+}:green) and 665 nm (Tm{sup 3+}, Ho{sup 3+}: red) from two separated cores was measured. Influence of fiber length and excitation power on the color coordinates (CIE-1931) have been also investigated. - Highlights: • Antimony-germanate glasses co-doped with Yb{sup 3+}/Tm{sup 3+} and Yb{sup 3+}/Ho{sup 3+} were presented. • UC luminescence in double-clad, two off-set core co-doped with Yb{sup 3+}/Tm{sup 3+} and Yb{sup 3+}/Ho{sup 3+} optical fiber was presented. • The chromatic coordinates shift in the blue region at CIE scheme as a function of pump power and length of optical fiber was observed.

  10. Synthesis and characterization of (Ba,Yb doped ceria nanopowders

    Directory of Open Access Journals (Sweden)

    Branko Matović

    2011-06-01

    Full Text Available Nanometric size (Ba, Yb doped ceria powders with fluorite-type structure were obtained by applying selfpropagating room temperature methods. Tailored composition was: Ce0.95−xBa0.05YbxO2−δ with fixed amount of Ba − 0.05 and varying Yb content “x” from 0.05 to 0.2. Powder properties such as crystallite and particle size and lattice parameters have been studied. Röntgen diffraction analyses (XRD were used to characterize the samples at room temperature. Also, high temperature treatment (up to 1550°C was used to follow stability of solid solutions. The mean diameters of the nanocrystals are determined from the full width at half maxima (FWHM of the XRD peaks. It was found that average diameter of crystallites is less than 3 nm. WilliamsonHall plots were used to separate the effect of the size and strain in the nanocrystals.

  11. Upconversion improvement in KLaF{sub 4}:Yb{sup 3+}/Er{sup 3+} nanoparticles by doping Al{sup 3+} ions

    Energy Technology Data Exchange (ETDEWEB)

    Zhou, Haifang [Fuzhou University, School of Physics and Information Engineering, and Institute of Micro-Nano Devices and Solar Cells, Fuzhou (China); Jiangsu Collaborative Innovation Center of Photovoltaic Science and Engineering, Changzhou, Jiangsu (China); Wang, Xiechun; Lai, Yunfeng; Cheng, Shuying; Zheng, Qiao; Yu, Jinlin [Fuzhou University, School of Physics and Information Engineering, and Institute of Micro-Nano Devices and Solar Cells, Fuzhou (China)

    2017-10-15

    Rare-earth ion-doped upconversion (UC) materials show great potential applications in optical and optoelectronic devices due to their novel optical properties. In this work, hexagonal KLaF{sub 4}:Yb{sup 3+}/Er{sup 3+} nanoparticles (NPs) were successfully synthesized by a hydrothermal method, and remarkably enhanced upconversion luminescence in green and red emission bands in KLaF{sub 4}:Yb{sup 3+}/Er{sup 3+} NPs has been achieved by doping Al{sup 3+} ions under 980 nm excitation. Compared to the aluminum-free KLaF{sub 4}:Yb{sup 3+}/Er{sup 3+} NPs sample, the UC fluorescence intensities of the green and red emissions of NPs doped with 10 at.% Al{sup 3+} ions were significantly enhanced by 5.9 and 7.3 times, respectively. Longer lifetimes of the doped samples were observed for the {sup 4}S{sub 3/2} state and {sup 4}F{sub 9/2} state. The underlying reason for the UC enhancement by doping Al{sup 3+} ions was mainly ascribed to distortion of the local symmetry around Er{sup 3+} ions and adsorption reduction of organic ligands on the surface of NPs. In addition, the influence of doping Al{sup 3+} ions on the structure and morphology of the NPs samples was also discussed. (orig.)

  12. Fluorescence properties of Yb3+-Er3+ co-doped phosphate glasses containing silver nanoparticles

    Science.gov (United States)

    Martínez Gámez, Ma A.; Vallejo H, Miguel A.; Kiryanov, A. V.; Licea-Jiménez, L.; Lucio M, J. L.; Pérez-García, S. A.

    2018-04-01

    Er3+-Yb3+ co-doped phosphate glasses containing silver nitrate (SN), were fabricated. Transmission electron microscopy (TEM) and x-ray photoelectron spectroscopy (XPS) analyses were used to evidence the nucleation and presence of silver nanoparticles (SNP). The basic parameters of the glasses were inspected by means of absorption and fluorescence spectra, and fluorescence lifetimes under excitation at 916 nm (in-band of Yb3+), and at 406 nm (in-band of surface plasmon resonance given by the presence of SNP). The spectra as well as estimates for the basic parameters defining the lasing/amplifying potential of the glasses were studied as a function of SN concentration. The experimental results indicate that by increasing the SN content an enhancement of Er3+/Yb3+ fluorescence takes place.

  13. Phosphate-core silica-clad Er/Yb-doped optical fiber and cladding pumped laser.

    Science.gov (United States)

    Egorova, O N; Semjonov, S L; Velmiskin, V V; Yatsenko, Yu P; Sverchkov, S E; Galagan, B I; Denker, B I; Dianov, E M

    2014-04-07

    We present a composite optical fiber with a Er/Yb co-doped phosphate-glass core in a silica glass cladding as well as cladding pumped laser. The fabrication process, optical properties, and lasing parameters are described. The slope efficiency under 980 nm cladding pumping reached 39% with respect to the absorbed pump power and 28% with respect to the coupled pump power. Due to high doping level of the phosphate core optimal length was several times shorter than that of silica core fibers.

  14. Microwave hydrothermal synthesis and upconversion properties of Yb3+/Er3+ doped YVO4 nanoparticles.

    Science.gov (United States)

    Kshetri, Yuwaraj K; Regmi, Chhabilal; Kim, Hak-Soo; Lee, Soo Wohn; Kim, Tae-Ho

    2018-05-18

    Yb 3+ and Er 3+ doped YVO 4 (Yb 3+ /Er 3+ :YVO 4 ) nanoparticles with highly efficient near-infrared to visible upconversion properties have been synthesized by microwave hydrothermal process. Uniform-sized Yb 3+ /Er 3+ :YVO 4 nanoparticles were synthesized within 1 h at 140 °C which is relatively faster than the conventional hydrothermal process. Under 980 nm laser excitation, strong green and less strong red emissions are observed which are attributed to 2 H 11/2 , 4 S 3/2 to 4 I 15/2 and 4 F 9/2 to 4 I 15/2 transitions of Er 3+ respectively. The emission intensity is found to depend strongly on the concentration of Yb 3+ . The quadratic dependence of upconversion intensity on the excitation power indicates that the upconversion process is governed by two-photon absorption process.

  15. Microwave hydrothermal synthesis and upconversion properties of Yb3+/Er3+ doped YVO4 nanoparticles

    Science.gov (United States)

    Kshetri, Yuwaraj K.; Regmi, Chhabilal; Kim, Hak-Soo; Wohn Lee, Soo; Kim, Tae-Ho

    2018-05-01

    Yb3+ and Er3+ doped YVO4 (Yb3+/Er3+:YVO4) nanoparticles with highly efficient near-infrared to visible upconversion properties have been synthesized by microwave hydrothermal process. Uniform-sized Yb3+/Er3+:YVO4 nanoparticles were synthesized within 1 h at 140 °C which is relatively faster than the conventional hydrothermal process. Under 980 nm laser excitation, strong green and less strong red emissions are observed which are attributed to 2H11/2, 4S3/2 to 4I15/2 and 4F9/2 to 4I15/2 transitions of Er3+ respectively. The emission intensity is found to depend strongly on the concentration of Yb3+. The quadratic dependence of upconversion intensity on the excitation power indicates that the upconversion process is governed by two-photon absorption process.

  16. Defects induced in Yb3+/Ce3+ co-doped aluminosilicate fiber glass preforms under UV and γ-ray irradiation

    DEFF Research Database (Denmark)

    Chiesa, Mario; Mattsson, Kent Erik; Taccheo, Stefano

    2014-01-01

    A set of Ce-/Yb-co-doped silica optical fiber preform cores, differing in terms of dopant concentrations are studied by Electron Paramagnetic Resonance (EPR) spectroscopy before and after irradiation of the samples with excimer UV laser light and γ-rays. Evidence of Yb3+ clustering in the case...

  17. High Efficiency InP Solar Cells from Low Toxicity Tertiarybutylphosphine

    Science.gov (United States)

    Hoffman, Richard W., Jr.; Fatemi, Navid S.; Wilt, David M.; Jenkins, Phillip P.; Brinker, David J.; Scheiman, David A.

    1994-01-01

    Large scale manufacture of phosphide based semiconductor devices by organo-metallic vapor phase epitaxy (OMVPE) typically requires the use of highly toxic phosphine. Advancements in phosphine substitutes have identified tertiarybutylphosphine (TBP) as an excellent precursor for OMVPE of InP. High quality undoped and doped InP films were grown using TBP and trimethylindium. Impurity doped InP films were achieved utilizing diethylzinc and silane for p and n type respectively. 16 percent efficient solar cells under air mass zero, one sun intensity were demonstrated with Voc of 871 mV and fill factor of 82.6 percent. It was shown that TBP could replace phosphine, without adversely affecting device quality, in OMVPE deposition of InP thus significantly reducing toxic gas exposure risk.

  18. Ytterbium doped silicon clusters YbSi{sub n} (n = 4–10) and their anions: Structures, thermochemistry, and electron affinities

    Energy Technology Data Exchange (ETDEWEB)

    Xie, Xiaohong [School of Chemical Engineering, Inner Mongolia University of Technology, Hohhot 010051 (China); Hao, Dongsheng [School of Chemical Engineering, Inner Mongolia University of Technology, Hohhot 010051 (China); School of Mining and Technology, Inner Mongolia University of Technology, Hohhot 010051 (China); Yang, Jucai, E-mail: yangjc@imut.edu.cn [School of Chemical Engineering, Inner Mongolia University of Technology, Hohhot 010051 (China); School of Energy and Power Engineering, Inner Mongolia University of Technology, Hohhot 010051 (China)

    2015-11-05

    Highlights: • The ground-state structure of YbSi{sub n} and its anion is substitutional structure. • The four DFT AEAs are in excellent agreement with the experimental data. • Theoretical AEA of 2.33 eV of YbSi{sub 9} is more reasonable than the experimental 2.60 eV. • Hardness analysis reveals that doping Yb to Si{sub n} raises photochemical sensitivity. • Relative stabilities of YbSi{sub n} and their anions are examined. - Abstract: The structures, electron affinities, dissociation energies, hardness, and dipole moments of YbSi{sub n} (n = 4–10) and their anions were examined using B3LYP, TPSSh, PBE and wB97X methods. The lowest-energy structures can be regarded as replacing a Si of the ground-state structure of Si{sub n+1} with a Yb atom. The theoretical adiabatic electron affinities (AEAs) of YbSi{sub n} are in excellent agreement with experimental data. The average absolute errors from experiment are by 0.08, 0.07, 0.05 and 0.08 eV at the B3LYP, the TPSSh, the PBE and the wB97X levels, respectively. Theoretical AEAs of 2.33 ± 0.05 eV for YbSi{sub 9} are more reliable than the experimental value of 2.60 ± 0.05 eV. The hardness analysis reveals that doping Yb atom to Si{sub n} (n = 4–10) clusters raises the photochemical sensitivity. The dissociation energies of Yb atom from YbSi{sub n} and their anions were calculated to examine relative stabilities.

  19. ODMR of shallow donors in Zn-doped LEC-grown InP

    International Nuclear Information System (INIS)

    Trombetta, J.M.; Kennedy, T.A.

    1990-01-01

    ODMR spectra observed while monitoring the shallow donor-shallow acceptor pair emission in Zn-doped LEC-grown InP display strong features in the region near the conduction electron value of g = 1.20. In addition to a previously observed narrow line, the authors observe a much broader resonance which dominates at low photoexcitation intensity. This broader line is interpreted as the unresolved exchange split resonances of electrons bound to residual shallow donors. The exchange broadening arises from interaction with nearby paramagnetic centers. Both resonances result in a decrease in the shallow-donor-to shallow-acceptor radiative recombination and give evidence for pair recombination processes which compete with this emission

  20. Visible and near infrared up-conversion luminescence in Yb3+/Tm3+ co-doped yttria-alumino-silicate glass based optical fibers

    International Nuclear Information System (INIS)

    Halder, Arindam; Chandra Paul, Mukul; Wadi Harun, Sulaiman; Kumar Bhadra, Shyamal; Bysakh, Sandip; Das, Shyamal; Pal, Mrinmay

    2013-01-01

    We report blue light up-conversion (UC) emission in Yb–Tm co-doped nano-phase separated yttria-alumino-silicate (YAS) glass based D-shaped with low-index cladding optical fibers. Y 2 O 3 creates an environment of nano structured YAS glass phases with Yb and Tm rich zone into the core glass which confirmed from TEM analyses. This kind of glass host assists in distributing of Yb and Tm rich zone uniformly throughout the core region. Yb and Tm doped regions exist mainly into nano YAS phases, defined as RE rich nano YAS-RE phases. All samples exhibit UC luminescence peaks at 483 nm, 650 nm and 817 nm for Tm 3+ and 1044 nm for Yb 3+ under excitation by 975 nm laser light. In such type of nano-engineered glass–ceramic based host, almost all the Yb ions transferred its energy to the nearer Tm ions. In particular 483 nm emission is attributed to 1 G 4 → 3 H 6 transition through a three step resonance energy transfer (ET) from excited Yb 3+ . The highest emission intensity is obtained with a concentration of 0.5 wt% Tm 3+ and 2.0 wt% Yb 3+ . The ET between Yb 3+ and Tm 3+ is increased with increase of Yb 3+ concentration with respect to Tm 3+ . The experimental fluorescence life-times of Tm 3+ upconversion emission at visible wavelengths into such kind of fiber is reported under 975 nm pump excitation. The present study is important for development of an efficient tunable 483 nm fluorescence light source. -- Highlights: • We report nano-phase separated YAS glass host based Yb–Tm co-doped optical fibers. • Almost all the Yb transferred its energy to the neighboring Tm ions. • We report strong UC luminescence peaks at 483 nm and 817 nm wavelengths. • We report third ET coefficient as 1.6723 Hz for such kind of Yb–Tm codoped fiber. • We report suitable fiber as an efficient tunable 483 nm fluorescence light source

  1. Oxygen plasma effects on zero resistance behavior of Yb,Er-doped YBCO (123) based superconductors

    Energy Technology Data Exchange (ETDEWEB)

    Schaefer, Helmut; Rathmann, Dirk [Department of Physics, Biophysics, and Photosynthesis, Freie Universitaet Berlin (Germany); Banko, Franziska; Steinhart, Martin [Physical Chemistry, Institute of Chemistry of New Materials, University of Osnabrueck (Germany); Nordmann, Joerg; Voss, Benjamin [Inorganic Chemistry, Institute of Chemistry of New Materials, University of Osnabrueck (Germany); Walder, Lorenz [Organic Chemistry, Molecular Electrochemistry, Institute of Chemistry of New Materials, University of Osnabrueck (Germany)

    2014-08-15

    Rare-earth doped YBa{sub 2}Cu{sub 3}O{sub 7-δ} samples were synthesized starting from the corresponding oxides Y{sub 2}O{sub 3}, Yb{sub 2}O{sub 3}, Er{sub 2}O{sub 3}, CuO as well as Ba(OH){sub 2} by heating to 950 C under air. The doping concentrations were adjusted to 15 % Yb, 7 % Er and 20 % Yb, 15 % Er, respectively, with respect to the yttrium content. The orthogonal phased (123) YBCO ceramics were exposed to an oxygen plasma for 140 and 380 min. Zero resistance temperature (T{sub c,0}) was determined by measuring the resistivity-temperature dependence using a classical four point measurement approach. Under optimal conditions with respect to the material composition and the oxygen treatment an unusual high zero resistance temperature of 97.5 K (T{sub c,onset} ∼ 101 K) was achieved. This represents an increase of T{sub c,0} by 7.5 K. The oxygen treatment could not be monitored by IR spectroscopy, X-ray fluorescence spectroscopy, and X-ray powder diffraction. The results showed good reproducibility. (Copyright copyright 2014 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  2. New configurations for short-pulses high power solid-state lasers: conception and realization of highly doped waveguide amplifiers/lasers grown by liquid phase epitaxy and demonstration of Y2SiO5: Yb and Lu2SiO5: Yb femtosecond lasers

    International Nuclear Information System (INIS)

    Thibault, F.

    2006-04-01

    Yb-doped yttrium and lutetium ortho-silicates, Y 2 SiO 5 :Yb and Lu 2 SiO 5 :Yb respectively, exhibit spectroscopic properties favorable to an efficient laser operation in both high power cw and femtosecond regime. Their first diode-pumped femtosecond operation demonstration lead to exceptional performances in terms of output power and efficiency. In order to realize compact and efficient solid-state laser devices using those materials, we chose a configuration with an Yb-doped medium planar waveguide geometry, grown by liquid phase epitaxy, face-pumped by a single laser diode bar. The growth of highly doped Y 2 SiO 5 :Yb layers, within a large range of compositions and thicknesses, was demonstrated. The refractive index increase due to the substitution of the various dopants is analyzed. The layers spectroscopic properties are similar to the bulk ones, with an noticeably higher crystalline quality. The Yb ion lifetime evolution with respect to its doping shows up a particularly low decrease, proof of a low concentration of extrinsic quenching centers. The covered YSO:24%Yb waveguides exhibit lower than 0.3 dB/cm propagation losses, and provided up to 2.9 dB/cm net amplification at 1082 nm with a single mode output. The realization of the first diode-pumped monolithic cw waveguide lasers was also demonstrated. For a 4% output coupler, they provided up to 340 mW at 1082 nm with a 14% slope efficiency. (author)

  3. Synthesis of Er and Er : Yb doped sol–gel derived silica glass and ...

    Indian Academy of Sciences (India)

    Unknown

    Materials Science Centre, †Central Research Facility, Optical Fibre Unit, Indian Institute of Technology,. Kharagpur 721 302, India. MS received 1 March 2004; revised 4 July 2004. Abstract. Er3+ and Er3+ : Yb3+ doped optical quality, crack and bubble free glasses for possible use in mak- ing laser material have been ...

  4. Direct comparison of Yb3+-doped LiYF4 and LiLuF4 as laser media at room-temperature

    International Nuclear Information System (INIS)

    Yin, J G; Hang, Y; He, X M; Zhang, L H; Zhao, C C; Gong, J; Zhang, P X

    2012-01-01

    We present an extensive comparative analysis on the growth, the spectroscopic features, and the laser performances of room temperature Yb(5%):LiYF 4 (YLF) and Yb(5%):LiLuF 4 (LLF) crystals in the same conditions. The gain cross section, fluorescence lifetimes, laser thresholds and laser slope efficiencies are compared for the first time. It appears that Yb 3+ -doped LLF crystal might be more promising for diode-pumped high power laser operation

  5. Room-temperature particle detectors with guard rings based on semi-insulating InP co-doped with Ti and Zn

    International Nuclear Information System (INIS)

    Yatskiv, R.; Zdansky, K.; Pekarek, L.

    2009-01-01

    Particle detectors made with a guard-ring (GR) electrode, operating at room temperature, have been studied. The detectors were fabricated on a semi-insulating InP crystal co-doped with Ti and Zn, grown using the Liquid-Encapsulated Czochralski technique. The detection performance of the particle detectors was evaluated using alpha particles emitted from a 241 Am source. Good detector performance has been achieved with measured charge-collection efficiencies of 99.9% and 98.2% and FWHM energy resolutions of 0.9% and 2.1%. The measurements were carried out at 230 K for negative and positive bias voltages of the irradiated electrode. The good performance is due to the SI properties of the material which has been achieved by doping with suitable Ti atoms and co-doping with a low concentration of Zn acceptors, sufficient to fully compensate shallow donors. Electron and hole charge-collection efficiencies (CCEs) were measured at various temperatures. At room temperature, unlike at low temperature (T<250 K), the hole CCE was better than the electron CCE, which can be explained by the presence of electron-trapping centres in InP with a temperature-dependent capture rate.

  6. Spectroscopic investigations of OH- influence on near-infrared fluorescence quenching of Yb3+/Tm3+ co-doped sodium-metaphosphate glasses

    International Nuclear Information System (INIS)

    Terra, I.A.A.; Camargo, A.S.S. de; Terrile, M.C.; Nunes, L.A.O.

    2008-01-01

    Energy transfer processes were studied in two sets of Yb 3+ and Tm 3+ co-doped sodium-metaphosphate glasses, prepared in air and nitrogen atmospheres. Using Foerster, Dexter, and Miyakawa theoretical models, the energy transfer parameters were calculated. The main ion-ion energy transfer processes analyzed were energy migration among Yb 3+ ions, cross-relaxations between Yb 3+ and Tm 3+ ions, and interactions with OH - radicals. The results indicated that Yb→Tm energy transfer favors 1.8 μm emissions, and there is no evidence of concentration quenching up to 2% Tm 2 O 3 doping. As expected, samples prepared in nitrogen atmosphere present higher fluorescence quantum efficiency than those prepared in air, and this feature is specially noted in the near-infrared region, where the interaction with the OH - radicals is more pronounced

  7. Characteristic of doping and diffusion of heavily doped n and p type InP and InGaAs epitaxial layers grown by metal organic chemical vapor deposition

    International Nuclear Information System (INIS)

    Pinzone, C.J.; Dupuis, R.D.; Ha, N.T.; Luftman, H.S.; Gerrard, N.D.

    1990-01-01

    Electronic and photonic device applications of the InGaAs/InP materials system often require the growth of epitaxial material doped to or near the solubility limit of the impurity in the host material. These requirements present an extreme challenge for the crystal grower. To produce devices with abrupt dopant profiles, preserve the junction during subsequent growth, and retain a high degree of crystalline perfection, it is necessary to understand the limits of dopant incorporation and the behavior of the impurity in the material. In this study, N-type doping above 10 19 cm -3 has been achieved in InP and InGaAs using Sn as a dopant. P-type Zn doping at these levels has also been achieved in these materials but p type activation above ∼3 x 10 18 cm -3 in InP has not been seen. All materials were grown by the metalorganic chemical vapor deposition (MOCVD) crystal growth technique. Effective diffusion coefficients have been measured for Zn and Sn in both materials from analysis of secondary ion mass spectra (SIMS) of specially grown and annealed samples

  8. Energy transfer and downconversion near-infrared material of Tb{sup 3+} and Yb{sup 3+} doped Ca{sub 5}(BO{sub 3}){sub 3}F

    Energy Technology Data Exchange (ETDEWEB)

    Hou, Dejian; Li, Jin-Yan [School of Metallurgy and Chemistry Engineering, Jiangxi University of Science and Technology, Ganzhou 341000, Jiangxi (China); Lin, Huihong, E-mail: linhh@hstc.edu.cn [School of Chemical and Environmental Engineering, Hanshan Normal University, Chaozhou 521041, Guangdong (China); Zhang, Jingxiang [School of Chemical and Environmental Engineering, Hanshan Normal University, Chaozhou 521041, Guangdong (China)

    2016-11-01

    Yb{sup 3+} and Tb{sup 3+} singly doped and Tb{sup 3+}–Yb{sup 3+} co-doped Ca{sub 5}(BO{sub 3}){sub 3}F phosphors were prepared by a solid state reaction method. The luminescence emission and excitation spectra as well as the luminescence decay curves were investigated. The emission bands of Yb{sup 3+} ion are located around 1000 nm, matching well with the optimal response of Si-based solar cells. Tb{sup 3+} can be a sensitizer for Yb{sup 3+} in the host. The energy transfer from Tb{sup 3+} to Yb{sup 3+} was investigated, the energy transfer mechanism was proposed as cooperative energy transfer. Tb{sup 3+} concentration dependent quantum efficiency was calculated and the maximum efficiency approached 115.5%.

  9. Near-infrared optical properties of Yb3+-doped silicate glass waveguides prepared by double-energy proton implantation

    Science.gov (United States)

    Shen, Xiao-Liang; Zhu, Qi-Feng; Zheng, Rui-Lin; Lv, Peng; Guo, Hai-Tao; Liu, Chun-Xiao

    2018-03-01

    We report on the preparation and properties of an optical planar waveguide structure operating at 1539 nm in the Yb3+-doped silicate glass. The waveguide was formed by using (470 + 500) keV proton implantation at fluences of (1.0 + 2.0) × 1016 ions/cm2. The waveguiding characteristics including the guided-mode spectrum and the near-field image were investigated by the m-line technique and the finite-difference beam propagation method. The energy distribution for implanted protons and the refractive index profile for the proton-implanted waveguide were simulated by the stopping and range of ions in matter and the reflectivity calculation method. The proton-implanted Yb3+-doped silicate glass waveguide is a candidate for optoelectronic elements in the near-infrared region.

  10. Yb and Er co-doped Y2Ce2O7 nanoparticles: synthesis and ...

    Indian Academy of Sciences (India)

    much attention due to their potential applications in display .... Figure 1. XRD patterns of Yb3+ and Er3+ co-doped Y2Ce2O7 nanoparticles prepared for 4 h at different sintering .... vels relax to the ground 4I15/2 level (You et al 2012). For.

  11. Emission characteristics of the Yb3+-sensitized Tm3+-doped optical fiber upon pumping with infrared LED

    International Nuclear Information System (INIS)

    Htein, Lin; Fan, Weiwei; Han, Won-Taek

    2014-01-01

    Near infrared emissions at 975, 1040 and 1450 nm of the Yb 3+ -sensitized Tm 3+ -doped optical fiber were obtained upon simultaneous excitation of Yb 3+ and Tm 3+ ions using the infrared LED. -- Highlights: • A novel pumping scheme for 1450 nm emission from 3 H 4 → 3 F 4 transition of Tm was demonstrated. • The absorption bands of Yb and Tm located within 690–970 nm were simultaneously excited with the IR LED. • Near infrared emissions at 975, 1040 and 1450 nm were obtained. • The Yb 3+ /Tm 3+ -codoped fiber showed the good spectroscopic quality and the increase of radiative lifetime of 3 H 4 level. • This LED pumping scheme can be useful for low-cost S-band fiber laser/amplifier applications

  12. High-efficiency silicon doping of InP and In0.53Ga0.47As in gas source and metalorganic molecular beam epitaxy using silicon tetrabromide

    International Nuclear Information System (INIS)

    Jackson, S.L.; Fresina, M.T.; Baker, J.E.; Stillman, G.E.

    1994-01-01

    Efficient vapor source Si doping of InP and In 0.53 Ga 0.47 As have been demonstrated using SiBr 4 as the Si source for both gas source (GSMBE) and metalorganic molecular beam epitaxy (MOMBE). Net electron concentrations ranging from n=2x10 17 to 6.8x10 19 cm -3 and from 9x10 16 to 3x10 19 cm -3 have been obtained for InP and In 0.53 Ga 0.47 As, respectively. Comparison of these data with those for Si 2 H 6 indicate that the Si incorporation efficiency with SiBr 4 is more than 10 000 times greater than with Si 2 H 6 for substrate temperatures in the range of 475≤T s ≤500 degree C. Specular surface morphologies were obtained, even for the most heavily doped samples. While [Si] as high as 1.8x10 20 cm -3 was obtained in InP, the net electron concentrations and 300 K Hall mobilities decrease with increasing [Si] for [Si]>6.8x10 19 cm -3 . Contact resistances as low as R c =3x10 -8 Ω cm 2 were obtained using a nonalloyed Ti/Pt/Au contact to InP layers doped to n=6.3x10 19 cm -3 . During GSMBE growth, an increased Si background concentration ([Si]∼2x10 17 cm -3 ) was observed after extended use of the SiBr 4 source for these heavy doping concentrations. This increased background was not observed in MOMBE-grown material. Depth profiles of pulse-doped structures indicate the absence of memory effects for structures grown by MOMBE

  13. Structure-Dependent Spectroscopic Properties of Yb3+-Doped Phosphosilicate Glasses Modified by SiO2

    Directory of Open Access Journals (Sweden)

    Ling Wang

    2017-02-01

    Full Text Available Yb3+-doped phosphate glasses containing different amounts of SiO2 were successfully synthesized by the conventional melt-quenching method. The influence mechanism of SiO2 on the structural and spectroscopic properties was investigated systematically using the micro-Raman technique. It was worth noting that the glass with 26.7 mol % SiO2 possessed the longest fluorescence lifetime (1.51 ms, the highest gain coefficient (1.10 ms·pm2, the maximum Stark splitting manifold of 2F7/2 level (781 cm−1, and the largest scalar crystal-field NJ and Yb3+ asymmetry degree. Micro-Raman spectra revealed that introducing SiO2 promoted the formation of P=O linkages, but broke the P=O linkages when the SiO2 content was greater than 26.7 mol %. Based on the previous 29Si MAS NMR experimental results, these findings further demonstrated that the formation of [SiO6] may significantly affect the formation of P=O linkages, and thus influences the spectroscopic properties of the glass. These results indicate that phosphosilicate glasses may have potential applications as a Yb3+-doped gain medium for solid-state lasers and optical fiber amplifiers.

  14. Structure-Dependent Spectroscopic Properties of Yb3+-Doped Phosphosilicate Glasses Modified by SiO2

    Science.gov (United States)

    Wang, Ling; Zeng, Huidan; Yang, Bin; Ye, Feng; Chen, Jianding; Chen, Guorong; Smith, Andew T.; Sun, Luyi

    2017-01-01

    Yb3+-doped phosphate glasses containing different amounts of SiO2 were successfully synthesized by the conventional melt-quenching method. The influence mechanism of SiO2 on the structural and spectroscopic properties was investigated systematically using the micro-Raman technique. It was worth noting that the glass with 26.7 mol % SiO2 possessed the longest fluorescence lifetime (1.51 ms), the highest gain coefficient (1.10 ms·pm2), the maximum Stark splitting manifold of 2F7/2 level (781 cm−1), and the largest scalar crystal-field NJ and Yb3+ asymmetry degree. Micro-Raman spectra revealed that introducing SiO2 promoted the formation of P=O linkages, but broke the P=O linkages when the SiO2 content was greater than 26.7 mol %. Based on the previous 29Si MAS NMR experimental results, these findings further demonstrated that the formation of [SiO6] may significantly affect the formation of P=O linkages, and thus influences the spectroscopic properties of the glass. These results indicate that phosphosilicate glasses may have potential applications as a Yb3+-doped gain medium for solid-state lasers and optical fiber amplifiers. PMID:28772601

  15. White upconversion luminescence in Tm3+/Ho3+/Yb3+ triply doped K+-Na+ ion-exchanged aluminum germanate glass channel waveguide

    Science.gov (United States)

    Liu, Xiao; Chen, Baojie; Pun, Edwin Yue Bun; Lin, Hai

    2013-01-01

    Rare-earth ions doped K+-Na+ ion-exchanged aluminum germanate (NMAG) glass channel waveguides have been designed and fabricated. Under 980 nm laser pumping, an intense upconversion white light transmission trace was observed in Tm3+/Ho3+/Yb3+ triply doped NMAG glass channel waveguide and a high-brightness light spot was achieved from the output end of the fiber connected to the waveguide channel. The fluorescent colors were diverse and located within or near the white region in CIE chromaticity diagram under various pumping powers. These admirable results indicate that Tm3+/Ho3+/Yb3+ triply doped NMAG channel waveguide is a promising light source for medical and high-precision processing illumination.

  16. Modifying the size and uniformity of upconversion Yb/Er:NaGdF4 nanocrystals through alkaline-earth doping.

    Science.gov (United States)

    Lei, Lei; Chen, Daqin; Huang, Ping; Xu, Ju; Zhang, Rui; Wang, Yuansheng

    2013-11-21

    NaGdF4 is regarded as an ideal upconversion (UC) host material for lanthanide (Ln(3+)) activators because of its unique crystal structure, high Ln(3+) solubility, low phonon energy and high photochemical stability, and Ln(3+)-doped NaGdF4 UC nanocrystals (NCs) have been widely investigated as bio-imaging and magnetic resonance imaging agents recently. To realize their practical applications, controlling the size and uniformity of the monodisperse Ln(3+)-doped NaGdF4 UC NCs is highly desired. Unlike the routine routes by finely adjusting the multiple experimental parameters, herein we provide a facile and straightforward strategy to modify the size and uniformity of NaGdF4 NCs via alkaline-earth doping for the first time. With the increase of alkaline-earth doping content, the size of NaGdF4 NCs increases gradually, while the size-uniformity is still retained. We attribute this "focusing" of size distribution to the diffusion controlled growth of NaGdF4 NCs induced by alkaline-earth doping. Importantly, adopting the Ca(2+)-doped Yb/Er:NaGdF4 NCs as cores, the complete Ca/Yb/Er:NaGdF4@NaYF4 core-shell particles with excellent size-uniformity can be easily achieved. However, when taking the Yb/Er:NaGdF4 NCs without Ca(2+) doping as cores, they could not be perfectly covered by NaYF4 shells, and the obtained products are non-uniform in size. As a result, the UC emission intensity of the complete core-shell NCs increases by about 30 times in comparison with that of the cores, owing to the effective surface passivation of the Ca(2+)-doped cores and therefore protection of Er(3+) in the cores from the non-radiative decay caused by surface defects, whereas the UC intensity of the incomplete core-shell NCs is enhanced by only 3 times.

  17. Upconversion and pump saturation mechanisms in Er3+/Yb3+ co-doped Y2Ti2O7 nanocrystals

    International Nuclear Information System (INIS)

    Wang, Fengxiao; Song, Feng; Zhang, Gong; Han, Yingdong; Li, Qiong; Tian, Jianguo; Ming, Chengguo

    2014-01-01

    The Er 3+ /Yb 3+ co-doped Y 2 Ti 2 O 7 nanocrystals were synthesized by the sol–gel method. X-ray diffraction, transmission electronic microscopy, and photoluminescence spectra were measured to verify the Y 2 Ti 2 O 7 nanocrystalline produced in the sample annealed at 800 °C. The anomalous slopes of the fitted line in the log-log plots for upconversion emissions and the pump-saturation effect of near-infrared emission were observed in the nanocrystalline samples. A theoretical model of practical Er 3+ /Yb 3+ co-doped system based on the rate equations were put forward and explained the experimental phenomena well

  18. Tm3+/Yb3+ co-doped tellurite glass with silver nanoparticles for 1.85 μm band laser material

    Science.gov (United States)

    Huang, Bo; Zhou, Yaxun; Cheng, Pan; Zhou, Zizhong; Li, Jun; Jin, Wei

    2016-10-01

    Tm3+/Yb3+ co-doped tellurite glasses with different silver nanoparticles (Ag NPs) concentrations were prepared using the conventional melt-quenching technique and characterized by the UV/Vis/NIR absorption spectra, 1.85 μm band fluorescence emission spectra, transmission electron microscopy (TEM) images, differential scanning calorimeter (DSC) curves and X-ray diffraction (XRD) patterns to investigate the effects of Ag NPs on the 1.85 μm band spectroscopic properties of Tm3+ ions, thermal stability and structural nature of glass hosts. Under the excitation of 980 nm laser diode (LD), the 1.85 μm band fluorescence emission of Tm3+ ions enhances significantly in the presence of Ag NPs with average diameter of ∼8 nm and local surface Plasmon resonance (LSPR) band of ∼590 nm, which is mainly attributed to the increased local electric field induced by Ag NPs at the proximity of doped rare-earth ions on the basis of energy transfer from Yb3+ to Tm3+ ions. An improvement by about 110% of fluorescence intensity is observed in the Tm3+/Yb3+ co-doped tellurite glass containing 0.5 mol% amount of AgNO3 while the prepared glass samples possess good thermal stability and amorphous structural nature. Meanwhile, the Judd-Ofelt intensity parameters Ωt (t = 2,4,6), spontaneous radiative transition probabilities, fluorescence branching ratios and radiative lifetimes of relevant excited levels of Tm3+ ions were determined based on the Judd-Ofelt theory to reveal the enhanced effects of Ag NPs on the 1.85 μm band spectroscopic properties, and the energy transfer micro-parameters and phonon contribution ratios were calculated based on the non-resonant energy transfer theory to elucidate the energy transfer mechanism between Yb3+ and Tm3+ ions. The present results indicate that the prepared Tm3+/Yb3+ co-doped tellurite glass with an appropriate amount of Ag NPs is a promising lasing media applied for 1.85 μm band solid-state lasers and amplifiers.

  19. Interfacial reactions between thin films of zinc and (100) InP

    International Nuclear Information System (INIS)

    Kaminska, E.; Piotrowska, A.; Barcz, A.; Mizera, E.; Dynowska, E.

    1995-01-01

    The effects of interaction between thin films of Zn and (100)InP were studied with secondary ion mass spectrometry, X-ray diffraction and transmission electron microscopy. Zn was found to penetrate the native oxide on InP surface during deposition and to form an ohmic contact when deposited on highly doped n-type InP. Heat treatment causes the formation of Zn 3 P 2 phase lattice matched to InP. (author)

  20. Lattice dynamics and substrate-dependent transport properties of (In, Yb)-doped CoSb3 skutterudite thin films

    KAUST Repository

    Sarath Kumar, S. R.; Cha, Dong Kyu; Alshareef, Husam N.

    2011-01-01

    Lattice dynamics, low-temperature electrical transport, and high-temperature thermoelectric properties of (In, Yb)-doped CoSb3thin films on different substrates are reported. Pulsed laser deposition under optimized conditions yielded single

  1. Electrical properties of InP irradiated by fast neutrons of a nuclear reactor

    International Nuclear Information System (INIS)

    Kolin, N.G.; Merkurisov, D.I.; Solov'ev, S.P.

    2000-01-01

    Electrophysical properties of InP single crystalline samples with different initial concentration of charge carriers have been studied in relation to irradiation conditions with fast neutrons of a nuclear reactor and subsequent heat treatments within the temperature range of 20-900 deg C. It has been shown that changes of the properties depend on the initial doping level. The annealing in the temperature range mentioned above results in the elimination of radiation defects. This makes possible to use the nuclear doping method for InP samples. In this respect the contribution of intermediate neutron reactions to the whole effect of the InP nuclear doping is estimated to be ∼ 10% [ru

  2. A study of 1/f noise in InP grown by CBE

    NARCIS (Netherlands)

    Chen, X.Y.; Leijs, M.R.

    1996-01-01

    The origin of low-frequency noise in InP was studied experimentally by measuring the noise of InP layers grown by chemical beam epitaxy (CBE). Such InP layers are unintentionally doped, but of varying purity and always of n-type conductivity. We performed noise measurements at temperatures from 77

  3. Mechanical properties of pure and doped InP single crystals under concentrated loading

    International Nuclear Information System (INIS)

    Boyarskaya, Yu.S.; Grabko, D.Z.; Medinskaya, M.I.; Palistrant, N.A.

    1997-01-01

    The mechanical properties of pure and doped (Fe, Zn, Sn) InP single crystals were investigated in the temperature interval from 293 to 600 K. It was shown that impurity hardening (the microhardness increase) was more pronounced at elevated temperatures than at 293 K. This is conditioned by braking of the moving dislocations with impurities which is more observed in the the high temperature region. The obvious anisotropy of the scratch hardness was revealed at room temperature for the (001) face of crystals under investigation. This anisotropy decreased sharply in increasing the temperature from 293 to 600 K

  4. The effect of intentional potassium co-doping on the luminescent properties of Yb3+ and Tm3+ doped α-NaYF4 core and core–shell nanoparticles

    International Nuclear Information System (INIS)

    Misiak, Małgorzata; Stręk, Wiesław; Arabasz, Sebastian; Bednarkiewicz, Artur

    2016-01-01

    Simple and effective ways to circumvent limited luminescence efficiency of up-converting nanoparticles (UCNPs) are sought. One of the methods relays on distorting the crystallographic structure of host material by co-doping the nanocrystals with optically inactive co-dopants. Here we study the influence of K + doping and surface passivation on the up-converting properties of the α-NaYF 4 nanocrystals co-doped with 20% Yb 3+ and 0.1 or 2% Tm 3+ . The intentionally chosen concentrations of K + ions, which were meant to replaced sodium ions were fixed to 0, 5, 10, 20 to 30%. Potassium ions modified the spectroscopic properties of both core and core–shell NPs, but the differences were noticed between samples doped with 0.1% Tm 3+ and 2% Tm 3+ ions. Replacement of sodium by potassium ions decreased up-conversion luminescence intensity as well as shortened thulium excited states lifetimes in the samples doped with 0.1% Tm 3+ , while the opposite behavior was found in the samples co-doped with higher 2% thulium concentration. - Highlights: • We studied the influence of K + doping on luminescent properties of α-NaYF 4 :YbTm. • The 0.1 and 2% Tm doped core and core–shell samples were investigated. • K + -doping influence on UC properties was different in low and highly Tm doped NPs. • The explanations of the observed variations were proposed.

  5. NIR to visible upconversion in Er3+/Yb3+ co-doped CaYAl3O7 phosphor obtained by solution combustion process

    International Nuclear Information System (INIS)

    Singh, Vijay; Rai, Vineet Kumar; Al-Shamery, Katharina; Nordmann, Joerg; Haase, Markus

    2011-01-01

    Using the combustion synthesis, CaYAl 3 O 7 :Er 3+ phosphor powders co-doped with Yb 3+ have been prepared at low temperatures (550 o C) in a few minutes. Formation of the compound was confirmed by X-ray powder diffraction. Near-infrared to visible upconversion fluorescence emission in the Er 3+ doped CaYAl 3 O 7 phosphor powder has been observed. The effect of co-doping with triply ionized ytterbium in the CaYAl 3 O 7 :Er 3+ phosphor has been studied and the process involved is discussed. - Highlights: → The green emitting up-conversion CaYAl 3 O 7 :Er 3+ phosphor powders co-doped with Yb 3+ have been prepared by easy combustion method. → The combustion method is a simple, energy saving, fast and economical viable process. → The luminescence intensity in the co-doped phosphor is enhanced by several times compared to that of the singly (Er 3+ ) doped phosphor.

  6. Electrical and microstructural properties of Yb-doped CeO2

    Directory of Open Access Journals (Sweden)

    B. Matović

    2014-06-01

    Full Text Available Nanopowdered Ce1−xYbxO2−δ solid solutions (0 ≤ x ≤ 0.2 were synthesized by a self-propagating room temperature synthesis. XRD and SEM were used to study the properties of these materials as well as the Yb solubility in CeO2 lattice. Results showed that all the obtained powders were solid solutions with a fluorite-type crystal structure and with nanometric particle size. The average size of Ce1−xYbxO2−δ particles was approximately 3 nm. Electrochemical impedance spectroscopy for the sintered pellets depicted that it was possible to separate Rbulk and Rgb in the temperature interval of 550–800 °C. The activation energy for the bulk conduction was 1.03 eV and for grain boundary conduction was 1.14 eV. Grain boundary resistivity dominates over the other resistivities. These measurements confirmed that Yb3+-doped CeO2 material had a potential as electrolyte for intermediate-temperature solid oxide fuel cell applications.

  7. Investigations on luminescence behavior of Er3+/Yb3+ co-doped boro-tellurite glasses

    Science.gov (United States)

    Maheshvaran, K.; Arunkumar, S.; Venkata Krishnaiah, K.; Marimuthu, K.

    2015-01-01

    Er3+/Yb3+ co-doped boro-tellurite glasses with the chemical composition 30TeO2+(24 - x)B2O3 + 15SrO + 10BaO + 10Li2O + 10LiF + 1Er2O3 + xYb2O3 (where x = 0, 0.1, 0.5, 1 and 2 in wt%) have been prepared and their luminescence behavior were studied and reported. Absorption spectral measurements have been used to derive the Judd-Ofelt (JO) intensity parameters from the experimental and calculated oscillator strength values following the JO theory. The various lasing parameters such as stimulated emission cross-section (σEp), experimental and calculated branching ratios (βR) and radiative lifetime (τcal) for the 2H9/2 → 4I15/2, 4S3/2 → 4I15/2 and 4I13/2 → 4I15/2 emission transitions were determined using the JO intensity parameters. The absorption and emission cross-section values for the 4I13/2 → 4I15/2 emission band have been calculated using McCumbar theory and the Gain cross-section for the 4I13/2 → 4I15/2 emission transition also obtained. The upconversion emission mechanism have been studied through various energy transfer processes and the intensity of the upconversion emission transitions are found to increase with the increase in Yb3+ ion concentration. The luminescence decay curves corresponding to the 4I13/2 → 4I15/2 transition of the Er3+/Yb3+ co-doped boro-tellurite glasses under 980 nm excitation wavelength have also been studied and reported in the present work.

  8. Enhanced infrared-to-visible up-conversion emission and temperature sensitivity in (Er3+,Yb3+, and W6+) tri-doped Bi4Ti3O12 ferroelectric oxide

    Science.gov (United States)

    Bokolia, Renuka; Mondal, Manisha; Rai, V. K.; Sreenivas, K.

    2017-02-01

    Strong up conversion (UC) luminescence at 527, 550, and 662 nm is compared under an excitation of 980 nm in single doped (Er3+), co-doped (Er3+/Yb3+), and (Er3+/Yb3+/W6+) tri-doped bismuth titanate (Bi4Ti3O12). For the co-doped system, the frequency (UC) emission intensity due to Er3+ ions is enhanced significantly in the green bands due to the efficient energy transfer from Yb3+ to Er3+ ions. Further increase in the emission intensity is seen with non-luminescent W6+ ions in the tri-doped system due to the modification in the local crystal field around the Er3+ ions, and is evidenced through a gradual change in the crystal structure of the host lattice with increasing W6+ content. The observed changes in the fluorescence lifetime and the associated energy transfer mechanisms are discussed. A progressive reduction of the lifetime of the 4S3/2 levels of Er3+ ions from 72 to 58.7 μs with the introduction of Yb3+ and W6+ dopant increases the transition probability and enhances the UC emission intensity. The efficiency of the energy transfer process ( η ) in the co-doped and tri-doped systems is found to be 9.4% and 18.6%, respectively, in comparison to the single doped system. Temperature sensing based on the fluorescence intensity ratio (FR) technique shows high sensitivity (0.0123 K-1) in the high temperature range (293 to 523 K) for an optimum content of Er3+, Yb3+, and W6+ with x = 0.03, y = 0.18, and z = 0.06 at. % in the tri-doped Bi4-x-yErxYbyTi3-zWzO12 ferroelectric composition, and is found useful for potential applications in optical thermometry.

  9. Two-wavelength, passive self-injection-controlled operation of diode-pumped cw Yb-doped crystal lasers.

    Science.gov (United States)

    Louyer, Yann; Wallerand, Jean-Pierre; Himbert, Marc; Deneva, Margarita; Nenchev, Marin

    2003-09-20

    We demonstrate and investigate a peculiar mode of cw Yb3+-doped crystal laser operation when two emissions, at two independently tunable wavelengths, are simultaneously produced. Both emissions are generated from a single pumped volume and take place in either a single beam or spatially separated beams. The laser employs original two-channel cavities that use a passive self-injection-locking (PSIL) control to reduce intracavity loss. The advantages of the application of the PSIL technique and some limitations are shown. The conditions for two-wavelength multimode operation of the cw quasi-three-level diode-pumped Yb3+ lasers and the peculiarity of such an operation are carried out both theoretically and experimentally. The results reported are based on the example of a Yb3+:GGG laser but similar results are also obtained with a Yb3+:YAG laser. The laser operates in the 1023-1033-nm (1030-1040-nm) range with a total output power of 0.4 W. A two-wavelength, single longitudinal mode generation is also obtained.

  10. Spectroscopic investigations of OH{sup -} influence on near-infrared fluorescence quenching of Yb{sup 3+}/Tm{sup 3+} co-doped sodium-metaphosphate glasses

    Energy Technology Data Exchange (ETDEWEB)

    Terra, I.A.A. [Instituto de Fisica de Sao Carlos, Universidade de Sao Paulo, Av. Trabalhador Saocarlense 400, CEP 13566-590, USP-Sao Carlos, SP (Brazil)], E-mail: idelma@ifsc.usp.br; Camargo, A.S.S. de; Terrile, M.C.; Nunes, L.A.O. [Instituto de Fisica de Sao Carlos, Universidade de Sao Paulo, Av. Trabalhador Saocarlense 400, CEP 13566-590, USP-Sao Carlos, SP (Brazil)

    2008-05-15

    Energy transfer processes were studied in two sets of Yb{sup 3+} and Tm{sup 3+} co-doped sodium-metaphosphate glasses, prepared in air and nitrogen atmospheres. Using Foerster, Dexter, and Miyakawa theoretical models, the energy transfer parameters were calculated. The main ion-ion energy transfer processes analyzed were energy migration among Yb{sup 3+} ions, cross-relaxations between Yb{sup 3+} and Tm{sup 3+} ions, and interactions with OH{sup -} radicals. The results indicated that Yb{yields}Tm energy transfer favors 1.8 {mu}m emissions, and there is no evidence of concentration quenching up to 2% Tm{sub 2}O{sub 3} doping. As expected, samples prepared in nitrogen atmosphere present higher fluorescence quantum efficiency than those prepared in air, and this feature is specially noted in the near-infrared region, where the interaction with the OH{sup -} radicals is more pronounced.

  11. Growth, characterization, and waveguide lasing of Yb3+, Lu3+, Gd3+ co-doped KY(WO4)2 thin layers

    NARCIS (Netherlands)

    Aravazhi, S.; Geskus, D.; Günther, D.; Worhoff, Kerstin; Pollnau, Markus

    2009-01-01

    Monoclinic crystals of KY(WO4)2 (KYW) doped with different rare-earth ions are among the highly promising materials for building compact solid-state lasers. We report the liquid phase epitaxy (LPE) growth of 3-5 µm thick KYW:Gd3+, Lu3+, Yb3+ layers for Yb3+ concentrations of 1.2, 1.7, and 2.4 mol%

  12. Enhanced monolayer MoS2/InP heterostructure solar cells by graphene quantum dots

    Science.gov (United States)

    Wang, Peng; Lin, Shisheng; Ding, Guqiao; Li, Xiaoqiang; Wu, Zhiqian; Zhang, Shengjiao; Xu, Zhijuan; Xu, Sen; Lu, Yanghua; Xu, Wenli; Zheng, Zheyang

    2016-04-01

    We demonstrate significantly improved photovoltaic response of monolayer molybdenum disulfide (MoS2)/indium phosphide (InP) van der Waals heterostructure induced by graphene quantum dots (GQDs). Raman and photoluminescence measurements indicate that effective charge transfer takes place between GQDs and MoS2, which results in n-type doping of MoS2. The doping effect increases the barrier height at the MoS2/InP heterojunction, thus the averaged power conversion efficiency of MoS2/InP solar cells is improved from 2.1% to 4.1%. The light induced doping by GQD provides a feasible way for developing more efficient MoS2 based heterostructure solar cells.

  13. Optical and electrical properties of Te doped AlGaAsSb/AlAsSb Bragg mirrors on InP

    OpenAIRE

    Toginho Filho, D. O.; Dias, I. F. L.; Duarte, J. L.; Laureto, E.

    2006-01-01

    We present a comparative study carried out on the optical and electrical characteristics of undoped and Te doped AlGaAsSb/AlAsSb Bragg mirrors with 6.5 pairs of layers and bulk undoped and Te doped AlGaAsSb epilayers alloys lattice matched on InP, grown by molecular beam epitaxy, using SIMS, photoluminescence, reflectivity and IxV techniques. The temperature dependence of PL transitions observed in the Bragg mirrors are similar to that observed in bulk samples and associated with the donor an...

  14. 1.8 μm luminescent properties and energy transfer of Yb{sup 3+}/Tm{sup 3+} co-doped α-NaYF{sub 4} single crystals

    Energy Technology Data Exchange (ETDEWEB)

    Feng, Zhigang [Key Laboratory of Photo-electronic Materials, Ningbo University, Ningbo, Zhejiang, 315211 (China); Xia, Haiping, E-mail: hpxcm@nbu.edu.cn [Key Laboratory of Photo-electronic Materials, Ningbo University, Ningbo, Zhejiang, 315211 (China); Wang, Cheng; Zhang, Zhixiong; Jiang, Dongsheng; Zhang, Jian; He, Shinan; Tang, Qingyang; Sheng, Qiguo; Gu, Xuemei; Zhang, Yuepin [Key Laboratory of Photo-electronic Materials, Ningbo University, Ningbo, Zhejiang, 315211 (China); Chen, Baojiu [Department of Physics, Dalian Maritime University, Dalian, Liaoning Province, 116026 (China); Jiang, Haochuan, E-mail: jianghaochuan@nimte.ac.cn [Ningbo Institute of Materials Technology and Engineering, The Chinese Academy of Sciences, Ningbo, Zhejiang, 315211 (China)

    2016-09-25

    This paper reports on successful preparation of α-NaYF{sub 4} single crystals co-doped with ∼1.9 mol% Tm{sup 3+} and various concentrations (3.85 mol%, 7.69 mol%, 11.54 mol%, 15.38 mol%) of Yb{sup 3+} by using a flux-Bridgman method. The fluorescence decay curve was measured to investigate the luminescent properties of the Yb{sup 3+}/Tm{sup 3+} co-doped α-NaYF{sub 4}, and the energy transfer process from Yb{sup 3+} to Tm{sup 3+}; the J-O intensity parameters of Tm{sup 3+} were further calculated and analyzed according to the absorption spectra. Results show that, an intense 1.8 μm emission was achieved with Yb{sup 3+} as sensitizer for Tm{sup 3+} in the α-NaYF{sub 4} single crystal under the excitation of 980 nm LD (Laser Diode) because of the strong energy transfer from Yb{sup 3+} to Tm{sup 3+}. The maximum emission intensity at 1.8 μm is obtained at about 15.38 mol% doping concentration of Yb{sup 3+} when the concentration of Tm{sup 3+} ions is fixed at ∼1.90 mol% in the current research. Moreover, the calculated maximum value of emission cross section at 1.8 μm is 1.63 × 10{sup −20} cm{sup 2} for 3.85 mol% Yb{sup 3+}/1.9 mol% Tm{sup 3+} sample, and the obtained energy transfer rate (W{sub ET}) and energy transfer efficiency (η) are 1543 s{sup −1} and 83.8%, respectively. Our analysis of the fluorescence dynamics indicates that electric dipole-dipole interaction is dominant for the energy transfer from Yb{sup 3+} ions to Tm{sup 3+} ions by using Inokuti-Hirayama’s model. - Highlights: • The Tm{sup 3+}/Yb{sup 3+} co-doped α-NaYF{sub 4} single crystals were grown by Bridgman method. • The 1.8 μm emission intensity is obtained at 15.38 mol% Yb{sup 3+}/1.90 mol% Tm{sup 3+} sample. • The maximum value of emission cross section at 1.8 μm is 1.63 × 10{sup −20} cm{sup 2}. • The energy transfer rate is 1543 s{sup −1} and energy transfer efficiency is 83.8%. • The physical mechanism for energy transfer from Yb{sup 3+} to Tm{sup 3+} ions

  15. Upconversion properties of Er3+/Yb3+ co-doped TeO2-TiO2-K2O glasses.

    Science.gov (United States)

    Su, Fangning; Deng, Zaide

    2006-01-01

    The Er3+/Yb3+ co-doped TeO2-TiO2-K2O glasses were prepared by conventional melting procedures, and their upconversion spectra were performed. The dependence of luminescence intensity on the ratio of Yb3+/Er3+ was studied, and the relationship between green upconversion luminescence intensity and Er3+ concentration is discussed in detail. The 546 nm green upconversion luminescence intensity is optimised in the studied glasses either when the Yb3+/Er3+ ratio is 25/1 and Er3+ concentration is 0.1 mol%, or when the Yb3+/Er3+ ratio is 10/1 and Er3+ concentration is 0.15 mol%. These glasses could be one of the potential candidates for LD pumping microchip solid-state lasers.

  16. Enhanced Power Conversion Efficiency of Perovskite Solar Cells with an Up-Conversion Material of Er3+-Yb3+-Li+ Tri-doped TiO2.

    Science.gov (United States)

    Zhang, Zhenlong; Qin, Jianqiang; Shi, Wenjia; Liu, Yanyan; Zhang, Yan; Liu, Yuefeng; Gao, Huiping; Mao, Yanli

    2018-05-11

    In this paper, Er 3+ -Yb 3+ -Li + tri-doped TiO 2 (UC-TiO 2 ) was prepared by an addition of Li + to Er 3+ -Yb 3+ co-doped TiO 2 . The UC-TiO 2 presented an enhanced up-conversion emission compared with Er 3+ -Yb 3+ co-doped TiO 2 . The UC-TiO 2 was applied to the perovskite solar cells. The power conversion efficiency (PCE) of the solar cells without UC-TiO 2 was 14.0%, while the PCE of the solar cells with UC-TiO 2 was increased to 16.5%, which presented an increase of 19%. The results suggested that UC-TiO 2 is an effective up-conversion material. And this study provided a route to expand the spectral absorption of perovskite solar cells from visible light to near-infrared using up-conversion materials.

  17. Polarized spectra calculation and continuous wave laser operation of Yb-doped disordered Ca3La2(BO3)4 crystal

    Science.gov (United States)

    Wang, Yeqing; Chen, Aixi; You, Zhenyu; Tu, Chaoyang

    2015-12-01

    A notable disorder crystal Yb:Ca3La2(BO3)4 crystal with Yb3+ ion doping concentration of 10 at.% was grown by the Czochralski method. The polarized absorption, polarized emission, and polarized gain cross sections were systematically calculated. The laser operations were investigated with Yb:Ca3La2(BO3)4 crystals cut along the a, b, and c crystallographic axes. The highest output power of 3.88 W was obtained by using the b-cut Yb:Ca3La2(BO3)4 crystal, with a slope efficiency of 62%. Additionally, it was confirmed that the output laser spectra were largely dependent on the output coupler.

  18. Polarized spectra calculation and continuous wave laser operation of Yb-doped disordered Ca3La2(BO3)4 crystal

    International Nuclear Information System (INIS)

    Wang, Yeqing; Chen, Aixi; You, Zhenyu; Tu, Chaoyang

    2015-01-01

    A notable disorder crystal Yb:Ca 3 La 2 (BO 3 ) 4 crystal with Yb 3+ ion doping concentration of 10 at.% was grown by the Czochralski method. The polarized absorption, polarized emission, and polarized gain cross sections were systematically calculated. The laser operations were investigated with Yb:Ca 3 La 2 (BO 3 ) 4 crystals cut along the a, b, and c crystallographic axes. The highest output power of 3.88 W was obtained by using the b-cut Yb:Ca 3 La 2 (BO 3 ) 4 crystal, with a slope efficiency of 62%. Additionally, it was confirmed that the output laser spectra were largely dependent on the output coupler. (paper)

  19. Unit cell parameters of wurtzite InP nanowires determined by x-ray diffraction.

    Science.gov (United States)

    Kriegner, D; Wintersberger, E; Kawaguchi, K; Wallentin, J; Borgström, M T; Stangl, J

    2011-10-21

    High resolution x-ray diffraction is used to study the structural properties of the wurtzite polytype of InP nanowires. Wurtzite InP nanowires are grown by metal-organic vapor phase epitaxy using S-doping. From the evaluation of the Bragg peak position we determine the lattice parameters of the wurtzite InP nanowires. The unit cell dimensions are found to differ from the ones expected from geometric conversion of the cubic bulk InP lattice constant. The atomic distances along the c direction are increased whereas the atomic spacing in the a direction is reduced in comparison to the corresponding distances in the zinc-blende phase. Using core/shell nanowires with a thin core and thick nominally intrinsic shells we are able to determine the lattice parameters of wurtzite InP with a negligible influence of the S-doping due to the much larger volume in the shell. The determined material properties will enable the ab initio calculation of electronic and optical properties of wurtzite InP nanowires.

  20. Dependence of upconversion emission intensity on Yb3+ concentration in Er3+/Yb3+ co-doped flake shaped Y2(MoO4)3 phosphors

    International Nuclear Information System (INIS)

    Lu Weili; Cheng Lihong; Zhong Haiyang; Sun Jiashi; Wan Jing; Tian Yue; Chen Baojiu

    2010-01-01

    Yttrium molybdate phosphors with fixed Er 3+ and various Yb 3+ concentrations were synthesized via a co-precipitation method. The crystal structure and the morphology of the phosphor were characterized by means of x-ray diffraction and field-emission scanning electron microscopy. Under 980 nm excitation, red and green upconversion emissions centred at 660, 553 and 530 nm were observed. Quantitative analyses on the dependence of upconversion emission intensity on the working current of a laser diode (LD) indicated that two-photon processes are responsible for both red and green upconversion emissions in both cases of low and high Yb 3+ concentrations. The relationship between the emission intensity ratio of 2 H 11/2 → 4 I 15/2 to 4 S 3/2 → 4 I 15/2 and the working current of the LD was studied for the samples doped with low and high Yb 3+ concentrations. Finally, a set of rate equations was established based on the possible upconversion mechanism, and an empirical formula was proposed to describe the Yb 3+ concentration dependence of upconversion emission intensity; the empirical formula fits well with the experimental data.

  1. Synthesis of Er(III)/Yb(III)-doped BiF3 upconversion nanoparticles for use in optical thermometry.

    Science.gov (United States)

    Du, Peng; Yu, Jae Su

    2018-03-23

    The authors describe an ethylene glycol assisted precipitation method for synthesis of Er(III)/Yb(III)-doped BiF 3 nanoparticles (NPs) at room temperature. Under 980-nm light irradiation, the NPs emit upconversion (UC) emission of Er(III) ions as a result of a two-photon absorption process. The temperature-dependent green emissions (peaking at 525 and 545 nm) are used to establish an unambiguous relationship between the ratio of fluorescence intensities and temperature. The NPs have a maximum sensitivity of 6.5 × 10 -3  K -1 at 619 K and can be applied over the 291-691 K temperature range. The results indicate that these NPs are a promising candidate for optical thermometry. Graphical abstract Schematic of the room-temperature preparation of Er(III)/Yb(III)-doped BiF 3 nanoparticles with strongly temperature-dependent upconversion emission.

  2. A broadening temperature sensitivity range with a core-shell YbEr@YbNd double ratiometric optical nanothermometer

    Science.gov (United States)

    Marciniak, L.; Prorok, K.; Francés-Soriano, L.; Pérez-Prieto, J.; Bednarkiewicz, A.

    2016-02-01

    The chemical architecture of lanthanide doped core-shell up-converting nanoparticles can be engineered to purposely design the properties of luminescent nanomaterials, which are typically inaccessible to their homogeneous counterparts. Such an approach allowed to shift the up-conversion excitation wavelength from ~980 to the more relevant ~808 nm or enable Tb or Eu up-conversion emission, which was previously impossible to obtain or inefficient. Here, we address the issue of limited temperature sensitivity range of optical lanthanide based nano-thermometers. By covering Yb-Er co-doped core nanoparticles with the Yb-Nd co-doped shell, we have intentionally combined temperature dependent Er up-conversion together with temperature dependent Nd --> Yb energy transfer, and thus have expanded the temperature response range ΔT of a single nanoparticle based optical nano-thermometer under single ~808 nm wavelength photo-excitation from around ΔT = 150 K to over ΔT = 300 K (150-450 K). Such engineered nanocrystals are suitable for remote optical temperature measurements in technology and biotechnology at the sub-micron scale.The chemical architecture of lanthanide doped core-shell up-converting nanoparticles can be engineered to purposely design the properties of luminescent nanomaterials, which are typically inaccessible to their homogeneous counterparts. Such an approach allowed to shift the up-conversion excitation wavelength from ~980 to the more relevant ~808 nm or enable Tb or Eu up-conversion emission, which was previously impossible to obtain or inefficient. Here, we address the issue of limited temperature sensitivity range of optical lanthanide based nano-thermometers. By covering Yb-Er co-doped core nanoparticles with the Yb-Nd co-doped shell, we have intentionally combined temperature dependent Er up-conversion together with temperature dependent Nd --> Yb energy transfer, and thus have expanded the temperature response range ΔT of a single nanoparticle

  3. Efficient conversion from UV light to near-IR emission in Yb{sup 3+}-doped triple-layered perovskite CaLaNb{sub 3}O{sub 10}

    Energy Technology Data Exchange (ETDEWEB)

    Lu, Yuting; Li, Yuze; Qin, Lin; Huang, Yanlin [College of Chemistry, Chemical Engineering and Materials Science, Soochow University, Suzhou 215123 (China); Qin, Chuanxiang, E-mail: qinchuanxiang@suda.edu.cn [College of Chemistry, Chemical Engineering and Materials Science, Soochow University, Suzhou 215123 (China); Tsuboi, Taiju [Jiangsu-Singapore Joint Research Center for Organic/Bio-Electronics & Information Displays and Institute of Advanced Materials (IAM), Nanjing Tech University, Nanjing 211816 (China); Huang, Wei, E-mail: wei-huang@njtech.edu.cn [Jiangsu-Singapore Joint Research Center for Organic/Bio-Electronics & Information Displays and Institute of Advanced Materials (IAM), Nanjing Tech University, Nanjing 211816 (China)

    2015-04-15

    Graphical abstract: CaRNb{sub 3}O{sub 10} is a self-activated oxide due to charge transfer transition in octahedral NbO{sub 6} groups. CaLaNb{sub 3}O{sub 10}:Yb{sup 3+} presents intense IR emission due to the cooperative energy transfer from host (NbO{sub 6}) to Yb{sup 3+} is responsible. It could be expected to be potentially applicable for enhancing photovoltaic conversion efficiency of Si-based solar cells. - Abstract: Yb{sup 3+}-doped triple-layered perovskite CaLaNb{sub 3}O{sub 10} micro-particles were synthesized via the solid-state reaction method. The crystal structure and morphology of the polycrystalline samples were investigated by X-ray powder diffraction (XRD) and scanning electron microscopy (SEM) measurements, respectively. The reflectance spectra, photoluminescence (PL) excitation and emission spectra, the decay curves, and the absolute quantum efficiency (QE) of the near-infrared (NIR) emission (910–1100 nm) were measured. Under excitation of UV light, Yb{sup 3+}-doped perovskite shows an intense NIR emission attributed to the {sup 2}F{sub 5/2} → {sup 2}F{sub 7/2} transitions of Yb{sup 3+} ions, which could match maximum spectral response of a Si-based solar cell. This is beneficial for its possible application in an enhancement of the photovoltaic conversion efficiency of solar energy utilization. The efficient energy transfer in Yb{sup 3+}-doped CaLaNb{sub 3}O{sub 10} from NbO{sub 6} groups into Yb{sup 3+} ions was confirmed by the spectra and fluorescent decay measurements. Cooperative energy transfer (CET) was supposed to be the NIR emission mechanism.

  4. Ultraviolet and near-infrared luminescence of LaBO3:Ce3+,Yb3+

    Science.gov (United States)

    Wei, Heng-Wei; Shao, Li-Ming; Jiao, Huan; Jing, Xi-Ping

    2018-01-01

    Ce3+ or Yb3+ singly doped LaBO3 and Ce3+-Yb3+ co-doped LaBO3 were prepared by conventional solid state reactions at 1100 °C and their photoluminescence (PL) properties were investigated. The emission spectrum of LaBO3:Ce3+,Yb3+ contains both the Ce3+ ultraviolet (UV) emissions (355 nm and 380 nm) and the Yb3+ near infrared (NIR) emission (975 nm) when excited by the UV light at 270 nm. By using the data of the Ce3+ decay curves and the PL intensities of both Ce3+ and Yb3+, the energy transfer efficiency (η) from Ce3+ to Yb3+, the actual energy transfer efficiency (AE) and the quantum efficiency (Q) of the Yb3+ emission were calculated. In the Ce3+-Yb3+ co-doped LaBO3, Ce3+ can transfer its absorbed energy to Yb3+ efficiently (η can be over 60%), and Yb3+ shows the Q value over 50% when it accepts the energy from Ce3+, which results in the low AE value ∼30%. The energy transfer process from Ce3+ to Yb3+ may be understood by the charge transfer mechanism: Ce3+ + Yb3+ ↔ Ce4+ + Yb2+. Particularly the Ce3+-Yb3+ co-doped LaBO3 phosphor gives the emissions mainly in the UV range and the NIR range with a portion of visible emissions in eye-insensitive range. This unique property may be suitable for applications in anti-counterfeiting techniques and public security affairs.

  5. Structural and magnetic properties of Mg doped YbMnO{sub 3}

    Energy Technology Data Exchange (ETDEWEB)

    Sattibabu, Bhumireddi, E-mail: bsb.satti@gmail.com [School of Engineering Sciences and Technology, University of Hyderabad, Hyderabad 500046 (India); Bhatnagar, Anil K., E-mail: anilb42@gmail.com [School of Engineering Sciences and Technology, University of Hyderabad, Hyderabad 500046 (India); School of Physics, University of Hyderabad, Hyderabad 500046 (India); Rayaprol, Sudhindra [UGC-DAE CSR, Mumbai Centre, R-5 Shed, BARC, Mumbai 400085 (India); Mohan, Dasari; Das, Dibakar; Sundararaman, Mahadevan [School of Engineering Sciences and Technology, University of Hyderabad, Hyderabad 500046 (India); Siruguri, Vasudeva [UGC-DAE CSR, Mumbai Centre, R-5 Shed, BARC, Mumbai 400085 (India)

    2014-09-01

    We have studied the effect of Mg doping on structure and magnetism of multiferroic YbMnO{sub 3}. Room temperature neutron diffraction studies were carried out on polycrystalline Yb{sub 1−x}Mg{sub x}MnO{sub 3} (x=0.00 and 0.05) samples to determine phase formation as well as cation distribution and structural properties such as bond length and bond angles. The structural analysis shows that with Mg substitution, there is a marginal change in a and c parameters of the hexagonal unit cell, c/a ratio remains constant for x=0 and 0.05 samples. Due to changes in bond angle and bond lengths on substituting Mg, there is a slight decrease in the distortion of MnO{sub 5} polyhedra. Magnetic measurements show that the Néel temperature (T{sub N}) increases marginally from 85 K for x=0.00 to 89 K for x=0.05 sample.

  6. Structural properties of pure and Fe-doped Yb films prepared by vapor condensation

    Energy Technology Data Exchange (ETDEWEB)

    Rojas-Ayala, C., E-mail: chachi@cbpf.br [Centro Brasileiro de Pesquisas Físicas, Rio de Janeiro 22290-180, RJ (Brazil); Facultad de Ciencias Físicas, Universidad Nacional Mayor de San Marcos, Lima, P.O.B. 14-149, Lima 14 (Peru); Passamani, E.C. [Departamento de Física, Universidade Federal do Espírito Santo, Vitória 29075-910, ES (Brazil); Suguihiro, N.M. [Centro Brasileiro de Pesquisas Físicas, Rio de Janeiro 22290-180, RJ (Brazil); Litterst, F.J. [Centro Brasileiro de Pesquisas Físicas, Rio de Janeiro 22290-180, RJ (Brazil); Institut für Physik der Kondensierten Materie, Technische Universität Braunschweig, 38106 Braunschweig (Germany); Baggio Saitovitch, E. [Centro Brasileiro de Pesquisas Físicas, Rio de Janeiro 22290-180, RJ (Brazil)

    2014-10-15

    Ytterbium and iron-doped ytterbium films were prepared by vapor quenching on Kapton substrates at room temperature. Structural characterization was performed by X-ray diffraction and transmission electron microscopy. The aim was to study the microstructure of pure and iron-doped films and thereby to understand the effects induced by iron incorporation. A coexistence of face centered cubic and hexagonal close packed-like structures was observed, the cubic-type structure being the dominant contribution. There is an apparent thickness dependence of the cubic/hexagonal relative ratios in the case of pure ytterbium. Iron-clusters induce a crystalline texture effect, but do not influence the cubic/hexagonal volume fraction. A schematic model is proposed for the microstructure of un-doped and iron-doped films including the cubic- and hexagonal-like structures, as well as the iron distribution in the ytterbium matrix. - Highlights: • Pure and Fe-doped Yb films have been prepared by vapor condensation. • Coexistence of fcc- and hcp-type structures was observed. • No oxide phases have been detected. • Fe-clustering does not affect the fcc/hcp ratio, but favors a crystalline texture. • A schematic model is proposed to describe microscopically the microstructure.

  7. Effects of Sm3+/Yb3+ co-doping and temperature on the Raman, IR spectra and structure of [TeO2-GeO2-K2O-Sm2O3/Yb2O3] glasses

    International Nuclear Information System (INIS)

    Shaltout, I.; Badr, Y.

    2006-01-01

    Effects of Sm 3+ /Yb 3+ co-doping on Raman scattering, IR absorption, temperature dependence of the Raman spectra up to 210 o C and the structure of two glass systems of the composition (80TeO 2 -10GeO 2 -8K 2 O-2Sm 2 O 3 /Yb 2 O 3 ) is discussed. It was found that the addition of Yb 3+ to the glass very strongly enhances the intensities of the antistokes' Raman bands at 155, 375, 557 and 828 cm -1 and quenches both the intensities of the stokes' vibration modes of the TeO 4 units in the range of 120-770 cm -1 and the intensities of the OH - stretching vibration modes in the range of 2600-3300 cm -1 . Sm 2 O 3 /Yb 2 O 3 rare earth co-doping has a great influence on removing and/or changing the nature of the OH - groups. The appearance and splitting of the stretching vibration modes of the OH - groups at lower frequencies (2770, 2970 cm -1 ) for the Sm +3 singly doped glass sample, compared to the band at ∼3200 cm -1 for the Sm 3+ /Yb 3+ co-doped glass sample, suggested that the OH - groups are more strongly bonded and incorporated with the glass matrix for the singly doped glass. Heating the sample up continuously weakens the hydrogen bonding of the OH - groups to the glass matrix leading to creation of NBO and breakdown of the connectivity of the OH - groups to the TeO 4 , TeO 3+1 and TeO 3 structural units. Raman bands at 286, 477, 666 and 769 cm -1 were assigned to its respective vibrations of Te 2 O 7 , TeO 4 -4 species, the (Te-O-Te) bending vibrations of the TeO 4 triagonal bipyramids (tbps), the axial symmetric stretching vibration modes (Te ax -O) s with bridging oxygen BO atoms and to the (Te-O) nbo non-bridging stretching vibration modes of the TeO 3+1 and/or TeO 3 pyramids

  8. Aptamer biosensor for Salmonella typhimurium detection based on luminescence energy transfer from Mn2 +-doped NaYF4:Yb, Tm upconverting nanoparticles to gold nanorods

    Science.gov (United States)

    Cheng, Keyi; Zhang, Jianguo; Zhang, Liping; Wang, Lun; Chen, Hongqi

    2017-01-01

    A highly sensitive luminescent bioassay for the detection of Salmonella typhimurium was fabricated using Mn2 +-doped NaYF4:Yb,Tm upconversion nanoparticles (UCNPs) as the donor and gold nanorods (Au NRs) as the acceptor and utilizing an energy transfer (LET) system. Mn2 +-doped NaYF4:Yb,Tm UCNPs with a strong emission peak at 807 nm were obtained by changing the doped ion ratio. Carboxyl-terminated Mn2 +-doped NaYF4:Yb,Tm UCNPs were coupled with S. typhimurium aptamers, which were employed to capture and concentrate S. typhimurium. The electrostatic interactions shorten the distance between the negatively charged donor and the positively charged acceptor, which results in luminescence quenching. The added S. typhimurium leads to the restoration of luminescence due to the formation of UCNPs-aptamers-S. typhimurium, which repels the UCNPs-aptamers from the Au NRs. The LET system does not occur because of the nonexistence of the luminescence emission band of Mn2 +-doped NaYF4:Yb,Tm UCNPs, which had large spectral overlap with the absorption band of Au NRs. Under optimal conditions, the linear range of detecting S. typhimurium was 12 to 5 × 105 cfu/mL (R = 0.99). The limit of detection for S. typhimurium was as low as 11 cfu/mL in an aqueous buffer. The measurement of S. typhimurium in milk samples was satisfied in accordance with the plate-counting method, suggesting that the proposed method was of practical value in the application of food security.

  9. Violet and visible up-conversion emission in Yb{sup 3+}-Ho{sup 3+} co-doped germanium-borate glasses

    Energy Technology Data Exchange (ETDEWEB)

    Yang Yanmin, E-mail: mihuyym@163.co [College of Physics Science and Technology, Hebei University, Baoding 071002 (China); Zhang Meixin [Forensic Science Lab, Hebei University, Baoding 071002 (China); Yang Zhiping [College of Physics Science and Technology, Hebei University, Baoding 071002 (China); Fu Zuoling [Key Laboratory of Coherent Light, Atomic and Molecular Spectroscopy, College of physics, Jilin University, Ministry of Education, Changchun 130023 (China)

    2010-10-15

    The up-conversion emission properties of Yb{sup 3+}-Ho{sup 3+} co-doped germanium-borate glasses have been investigated with 980 nm excitation. The violet, blue, green and red emission bands at about 350, 485, 544 and 653 nm can be identified, respectively. Experimental results indicated that the relative intensity ratios of the peaks I{sub Red}/I{sub Green} increased with increasing B{sub 2}O{sub 3} concentration, which led to changing color of up-conversion emission from green at x=0 to yellow at x=40, to red at x=60. The violet emission at 350 nm was first reported in germanium-borate glass host and up-conversion mechanisms of the emissions were discussed. The Yb{sup 3+}-Ho{sup 3+} co-doped germanium-borate glasses could be an alternative for the generation of violet and primary colors for application in solid-state displays.

  10. Study of upconversion fluorescence property of novel Er3+/Yb3+ co-doped tellurite glasses.

    Science.gov (United States)

    Xu, Tie-Feng; Li, Guang-Po; Nie, Qiu-Hua; Shen, Xiang

    2006-06-01

    Er3+/Yb3+ co-doped TeO2-B2O3-Nb2O5-ZnO (TBN) glasses were prepared. The absorption spectra and upconversion luminescence spectra of TBN glasses were measured and analyzed. The upconversion emission bands centered at 530, 546 and 658 nm were observed under the excitation at 975 nm, corresponding to the transitions of 2H11/2-->4I15/2, 4S3/2-->4I15/2 and 4F9/2-->4I15/2 respectively. The ratio of red emission to green emission increases with an increasing of Yb3+ ions concentration. According to the quadratic dependence on excitation power, the possible upconversion mechanisms and processes were discussed.

  11. Optical gain at 1.53 {mu}m in Er{sup 3+}-Yb{sup 3+} co-doped porous silicon waveguides

    Energy Technology Data Exchange (ETDEWEB)

    Najar, A. [Laboratoire d' Optronique UMR 6082-FOTON, Universite de Rennes 1, 6 rue de Kerampont, BP 80518, 22305 Lannion Cedex (France); Laboratoire de Spectroscopie Raman, Faculte des Sciences de Tunis, 2092 El Manar, Tunis (Tunisia)], E-mail: najar.adel@laposte.net; Charrier, J. [Laboratoire d' Optronique UMR 6082-FOTON, Universite de Rennes 1, 6 rue de Kerampont, BP 80518, 22305 Lannion Cedex (France); Ajlani, H. [Laboratoire de Spectroscopie Raman, Faculte des Sciences de Tunis, 2092 El Manar, Tunis (Tunisia); Lorrain, N.; Haesaert, S. [Laboratoire d' Optronique UMR 6082-FOTON, Universite de Rennes 1, 6 rue de Kerampont, BP 80518, 22305 Lannion Cedex (France); Oueslati, M. [Laboratoire de Spectroscopie Raman, Faculte des Sciences de Tunis, 2092 El Manar, Tunis (Tunisia); Haji, L. [Laboratoire d' Optronique UMR 6082-FOTON, Universite de Rennes 1, 6 rue de Kerampont, BP 80518, 22305 Lannion Cedex (France)

    2008-01-15

    Erbium-ytterbium (Er-Yb)-co-doped porous silicon planar waveguides were prepared from P{sup +}-type (1 0 0) oriented silicon wafer. Erbium and ytterbium ions were electrochemically introduced into the porous structure of the waveguide core. The doping profiles of erbium and ytterbium ions were determined by EDX analysis performed on sample cross-section. The mean concentration in the guiding layer is of about 1 x 10{sup 20} cm{sup -3}. The refractive indices were measured from co-doped porous silicon and undoped waveguides after the thermal treatments. The photoluminescence (PL) peak of optically activated erbium ions at 1.53 {mu}m was recorded. The PL enhancement is the result of the energy transfer from the excited state of Yb to the state of Er. Optical losses at 1.55 {mu}m were measured on these waveguides and were of about 2 dB/cm. An internal gain at 1.53 {mu}m of 5.8 dB/cm has been measured with a pump power of 65 mW at 980 nm.

  12. kW-level commercial Yb-doped aluminophosphosilicate ternary laser fiber

    Science.gov (United States)

    Sun, Shihao; Zhan, Huan; Li, Yuwei; Liu, Shuang; Jiang, Jiali; Peng, Kun; Wang, Yuying; Ni, Li; Wang, Xiaolong; Jiang, Lei; Yu, Juan; Liu, Gang; Lu, Pengfei; Wang, Jianjun; Jing, Feng; Lin, Aoxiang

    2018-03-01

    Based on a master oscillator power amplifier configuration, laser performance of commercial Nufern-20/400-8M Ybdoped aluminophosphosilicate ternary laser fiber was investigated. Pumped by 976 nm laser diodes, 982 W laser output power was obtained with a slope efficiency of 84.9%. Spectrum of output was centered at 1066.56nm with 3dB bandwidth less than 0.32 nm, and the nonlinearity suppression ratio was more than 39dB. Beam quality of Mx2 and M2y were 1.55 and 1.75 at 982 W, respectively. The laser performance indicated that Nufern-20/400-8M Yb-doped aluminophosphosilicate ternary laser fiber is highly competitive for industry fiber laser use.

  13. Thermal analyzes of phosphate glasses doped with Yb{sup 3+} and ZnTe nanocrystals

    Energy Technology Data Exchange (ETDEWEB)

    Freitas, A.M.; Bell, M.J.V. [Laboratório de Espectroscopia de Materiais, Departamento de Física, ICE, Universidade Federal de Juiz de Fora, 36036-330 Juiz de Fora, MG (Brazil); Anjos, V., E-mail: virgilio@fisica.ufjf.br [Laboratório de Espectroscopia de Materiais, Departamento de Física, ICE, Universidade Federal de Juiz de Fora, 36036-330 Juiz de Fora, MG (Brazil); Pinheiro, A.S.; Dantas, N.O. [Laboratório de Novos Materiais Isolantes e Semicondutores (LNMIS), Instituto de Física da Universidade Federal de Uberlândia, CP 593, CEP 38400-902 Uberlândia, MG (Brazil)

    2016-01-15

    This work studies the thermal properties of a glass matrix called PZABP doped with ZnTe and co-doped with Yb{sup 3+} with nominal composition 60P{sub 2}O{sub 5}, 15ZnO, 5Al{sub 2}O{sub 3}, 10BaO, and 10 PbO (mol%). The presence of ZnTe results in the formation of nanocrystals which are evidenced by optical absorption, X-Ray Diffraction (XRD) and Raman scattering. Thermal lens and Volumetric Heat Capacity techniques were used to investigate thermal diffusivity (D), thermal conductivity (K) and optical path variation with temperature (ds/dT). The outcomes indicate high values for the thermal diffusivity and a relatively small thermal conductivity, i.e., around 2.6×10{sup −3} cm{sup 2}/s and 3.4×10{sup −3} W cm{sup −1} K{sup −1}, respectively. On the other hand, a low ds/dT value, 1.0×10{sup −6} K{sup −1}, was obtained as required for an active laser medium. Moreover, it has been observed that the matrix allows high concentration of dopants without compromising its thermal properties. As a result, PZABP glasses may be pointed out as a promising material to applications in high power photonics devices. - Highlights: • UV transparentglass matrix (PZABP) is used for Yb{sup 3+}doping. • Bulk like and quantum dots like crystals of ZnTe were grown. • Thermal properties point out PZABP as a material to high power photonics devices.

  14. Study on upconversion luminescence and thermal properties of Ho{sup 3+}/Yb{sup 3+} co-doped La{sub 2}O{sub 3}–TiO{sub 2}–ZrO{sub 2} glasses

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Minghui; Wen, Haiqin [State Key Laboratory of High Performance Ceramics and Superfine Microstructure, Shanghai Institute of Ceramics, Chinese Academy of Sciences, Shanghai, 200050 (China); Yu, Huimei [Analysis and Testing Center of Inorganic Materials, Shanghai Institute of Ceramics, Chinese Academy of Sciences, Shanghai, 200050 (China); Ai, Fei [State Key Laboratory of High Performance Ceramics and Superfine Microstructure, Shanghai Institute of Ceramics, Chinese Academy of Sciences, Shanghai, 200050 (China); Shao, Hui [School of Materials Science and Engineering, Jiangsu University of Science and Technology, Zhenjiang, 212003 (China); Pan, Xiuhong; Tang, Meibo; Yu, Jianding; Gai, Lijun [State Key Laboratory of High Performance Ceramics and Superfine Microstructure, Shanghai Institute of Ceramics, Chinese Academy of Sciences, Shanghai, 200050 (China); Liu, Yan, E-mail: liuyan@mail.sic.ac.cn [State Key Laboratory of High Performance Ceramics and Superfine Microstructure, Shanghai Institute of Ceramics, Chinese Academy of Sciences, Shanghai, 200050 (China)

    2016-07-05

    Bulk Ho{sup 3+}/Yb{sup 3+} co-doped La{sub 2}O{sub 3}–TiO{sub 2}–ZrO{sub 2} glass spheres were fabricated by aerodynamic levitation method. High concentration of Yb{sup 3+} ions was successfully doped in glasses. The effects of Yb{sup 3+} concentration on mechanical properties, Raman, absorption spectra, thermal stability, and glass forming ability were studied systematically. Green, red, and infrared emissions centered at 550, 662, and 758 nm were obtained at 980 nm excitation. Yellow light from glass spheres can be easily observed by naked eyes. As Yb{sup 3+} concentration increases, the upconversion luminescence can be improved obviously. The upconversion luminescence mechanism is a two-photon process of energy transfer, excited state absorption, and energy back transfer. The emission intensity can be enhanced in the samples with high Yb{sup 3+} concentration, since the absorption for the incident laser and the energy transfer efficiency are increased, and the nonradiative relaxation probability is reduced. The light color referring to the ratio for red to green emissions can be tuned by Yb{sup 3+} concentration. Ho{sup 3+}/Yb{sup 3+} co-doped La{sub 2}O{sub 3}–TiO{sub 2}–ZrO{sub 2} glasses show promising comprehensive properties and are helpful to speed the application of upconversion luminescence materials. - Highlights: • Ho{sup 3+}/Yb{sup 3+} doped titanate glasses are prepared by containerless processing. • The effects of Yb{sup 3+} on thermal and mechanical properties have been studied. • High concentration of Yb{sup 3+} is favorable to upconversion luminescence. • The mechanisms are energy transfer, excited state absorption, energy back transfer.

  15. Multifunctional Eu3+- and Er3+/Yb3+-doped GdVO4 nanoparticles synthesized by reverse micelle method.

    Science.gov (United States)

    Gavrilović, Tamara V; Jovanović, Dragana J; Lojpur, Vesna; Dramićanin, Miroslav D

    2014-02-27

    Synthesis of Eu(3+)- and Er(3+)/Yb(3+)-doped GdVO4 nanoparticles in reverse micelles and their multifunctional luminescence properties are presented. Using cyclohexane, Triton X-100, and n-pentanol as the oil, surfactant, and co-surfactant, respectively, crystalline nanoparticles with ~4 nm diameter are prepared at low temperatures. The particle size assessed using transmission electron microscopy is similar to the crystallite size obtained from X-ray diffraction measurements, suggesting that each particle comprises a single crystallite. Eu(3+)-doped GdVO4 nanoparticles emit red light through downconversion upon UV excitation. Er(3+)/Yb(3+)-doped GdVO4 nanoparticles exhibit several functions; apart from the downconversion of UV radiation into visible green light, they act as upconvertors, transforming near-infrared excitation (980 nm) into visible green light. The ratio of green emissions from (2)H11/2 → (2)I15/2 and (4)S3/2 → (4)I15/2 transitions is temperature dependent and can be used for nanoscale temperature sensing with near-infrared excitation. The relative sensor sensitivity is 1.11%K(-1), which is among the highest sensitivities recorded for upconversion-luminescence-based thermometers.

  16. Multifunctional Eu3+- and Er3+/Yb3+-doped GdVO4 nanoparticles synthesized by reverse micelle method

    Science.gov (United States)

    Gavrilović, Tamara V.; Jovanović, Dragana J.; Lojpur, Vesna; Dramićanin, Miroslav D.

    2014-02-01

    Synthesis of Eu3+- and Er3+/Yb3+-doped GdVO4 nanoparticles in reverse micelles and their multifunctional luminescence properties are presented. Using cyclohexane, Triton X-100, and n-pentanol as the oil, surfactant, and co-surfactant, respectively, crystalline nanoparticles with ~4 nm diameter are prepared at low temperatures. The particle size assessed using transmission electron microscopy is similar to the crystallite size obtained from X-ray diffraction measurements, suggesting that each particle comprises a single crystallite. Eu3+-doped GdVO4 nanoparticles emit red light through downconversion upon UV excitation. Er3+/Yb3+-doped GdVO4 nanoparticles exhibit several functions; apart from the downconversion of UV radiation into visible green light, they act as upconvertors, transforming near-infrared excitation (980 nm) into visible green light. The ratio of green emissions from 2H11/2 --> 2I15/2 and 4S3/2 --> 4I15/2 transitions is temperature dependent and can be used for nanoscale temperature sensing with near-infrared excitation. The relative sensor sensitivity is 1.11%K-1, which is among the highest sensitivities recorded for upconversion-luminescence-based thermometers.

  17. Effect of silica surface coating on the luminescence lifetime and upconversion temperature sensing properties of semiconductor zinc oxide doped with gallium(III) and sensitized with rare earth ions Yb(III) and Tm(III).

    Science.gov (United States)

    Li, Yuemei; Li, Yongmei; Wang, Rui; Zheng, Wei

    2018-02-26

    Optical sensing of temperature by measurement of the ratio of the intensities of the 700 nm emission and the 800 nm emission of Ga(III)-doped ZnO (GZO) nanoparticles (NPs) and of GZO NPs coated with a silica shell are demonstrated at 980 nm excitation. It is found that the relative sensitivity of SiO 2 @Yb/Tm/GZO is 6.2% K -1 at a temperature of 693 K. This is ~3.4 times higher than that of Yb/Tm/GZO NPs. Obviously, the SiO 2 shell structure decreases the rate of the nonradiative decay. The decay time of the 800 nm emission of the Yb/Tm/GZO NPs (15 mol% Ga; 7 mol% Yb; 0.5 mol% Tm) displays a biexponential decay with a dominant decay time of 148 μs and a second decay time of ~412 μs. The lifetime of the Yb/Tm/GZO NPs at 293 K, and of the SiO 2 @Yb/Tm/GZO NPs are ~412 μs. Both the Yb/Tm/GZO and SiO 2 @Yb/Tm/GZO can be used up to 693 K. These results indicate that the SiO 2 shell on the Yb/Tm/GZO is beneficial in terms of sensitivity and resolution. Graphical abstract The enhancement the decay time and thermal sensitivity in the SiO 2 @Yb/Tm/GZO shell@core structure have been studied compared to the Ga(III)-doped Yb/Tm-doped ZnO (Yb/Tm/GZO). The SiO 2 @Yb/Tm/GZO have good thermal accuracy up to 693 °C.

  18. Quantum efficiency of Yb{sup 3+}–ZnTe co-doped phosphate glass system

    Energy Technology Data Exchange (ETDEWEB)

    Falci, R.F.; Freitas, A.M.; Silva, G.H. [Laboratório de Espectroscopia de Materiais, Departamento de Física, ICE, Universidade Federal de Juiz de Fora, 36036-330, Juiz de Fora, MG (Brazil); Pinheiro, A.S. [Centro Federal de EducaçãoTecnológica Celso Suckow da Fonseca (CEFET/RJ) - Campus Petrópolis, CEP 25620-003, Petrópolis - RJ (Brazil); Dantas, N.O. [Laboratório de Novos Materiais Isolantes e Semicondutores (LNMIS), Instituto de Física da Universidade Federal de Uberlândia, CP 593, CEP 38400-902, Uberlândia, MG (Brazil); Anjos, V., E-mail: virgilio@fisica.ufjf.br [Laboratório de Espectroscopia de Materiais, Departamento de Física, ICE, Universidade Federal de Juiz de Fora, 36036-330, Juiz de Fora, MG (Brazil); Bell, M.J.V. [Laboratório de Espectroscopia de Materiais, Departamento de Física, ICE, Universidade Federal de Juiz de Fora, 36036-330, Juiz de Fora, MG (Brazil)

    2016-08-15

    The present paper deals with optical properties of a highly transparent phosphate glass co-doped with Yb{sup 3+} and ZnTe nanocrystals. The presence of ZnTe nanocrystals is due to a sequential melting–nucleation procedure evidenced by optical absorption and Atomic Force Microscopy. From the perspective of compositional variation of the dopants, photoluminescence and lifetime measurements were performed. As a result, it was demonstrated that the ZnTe nanocrystals increase the Yb{sup 3+} emission by a factor up to five, when the pumping wavelength is resonant with the ZnTe absorption. It was also verified that the ZnTe nanocrystals inhibit the self-trapping of the rare earth luminescence. As a consequence, the quantum efficiency of the {sup 5}F{sub 7/2}→{sup 5}F{sub 5/2} transitions of the Yb{sup 3+} is considerably increased. Finally, we have found that the glass thermal diffusivity is not sensitive to temperature variations comprising the interval from room temperature to cryogenic temperatures. This can be an important property when considering this material to future applications in high-power photonic devices.

  19. Thermal effects on light emission in Yb3+ -sensitized rare-earth doped optical glasses

    International Nuclear Information System (INIS)

    Gouveia, E.A.; Araujo, M.T. de; Gouveia-Neto, A.S.

    2001-01-01

    The temperature effect upon infrared-to-visible frequency upconversion fluorescence emission in off-resonance infrared excited Yb 3+ -sensitized rare-earth doped optical glasses is theoretically and experimentally investigated. We have examined samples of Er3+/Yb 3+ -codoped Ga 2 S 3 :La 2 O 3 chalcogenide glasses and germanosilicate optical fibers, and Ga2O3:La 2 O 3 chalcogenide and fluoroindate glasses codoped with Pr 3+ /Yb 3+ , excited off-resonance at 1.064μm. The experimental results revealed thermal induced enhancement in the visible upconversion emission intensity as the samples temperatures were increased within the range of 20 deg C to 260 deg C. The fluorescence emission enhancement is attributed to the temperature dependent multiphonon-assisted anti-Stokes excitation process of the ytterbium-sensitizer. A theoretical approach that takes into account a sensitizer temperature dependent effective absorption cross section, which depends upon the phonon occupation number in the host matrices, has proven to agree very well with the experimental data. As beneficial applications of the thermal enhancement, a temperature tunable amplifier and a fiber laser with improved power performance are presented. (author)

  20. Up-conversion luminescence of Er3+/Yb3+/Nd3+-codoped tellurite glasses

    International Nuclear Information System (INIS)

    Lu Longjun; Nie Qiuhua; Xu Tiefeng; Dai Shixun; Shen Xiang; Zhang Xianghua

    2007-01-01

    Up-conversion luminescence and energy transfer (ET) processes in Nd 3+ -Yb 3+ -Er 3+ triply doped TeO 2 -ZnO-Na 2 O glasses have been studied under 800 nm excitation. Intense green up-conversion emissions around 549 nm, which can be attributed to the Er 3+ : 4 S 3/2 →4 I 15/2 transition, are observed in triply doped samples. In contrast, the green emissions are hardly observed in Er 3+ singly doped and Er 3+ -Yb 3+ codoped samples under the same condition. Up-conversion luminescence intensity exhibits dependence of Yb 2 O 3 -concentration and Nd 2 O 3 -concentration. Up-conversion mechanism in the triply doped glasses under 800 nm pump is discussed by analyzing the ET among Nd 3+ , Yb 3+ and Er 3+ . And a possible up-conversion mechanism based on sequential ET from Nd 3+ to Er 3+ through Yb 3+ is proposed for green and red up-conversion emission processes

  1. Cooperative up-conversion processes in SrAl{sub 4}O{sub 7}:Yb and SrAl{sub 4}O{sub 7}:Yb,Tb and their dependence on charge compensation by Na

    Energy Technology Data Exchange (ETDEWEB)

    Puchalska, M., E-mail: malgorzata.puchalska@chem.uni.wroc.pl [Faculty of Chemistry, University of Wroclaw, 14, F. Joliot-Curie Street, 50-383 Wroclaw (Poland); Zych, E. [Faculty of Chemistry, University of Wroclaw, 14, F. Joliot-Curie Street, 50-383 Wroclaw (Poland); Watras, A. [Institute of Low Temperature and Structure Research, Polish Academy of Sciences, 2 Okólna Street, 50-422 Wrocław (Poland)

    2017-03-15

    A detailed analysis of the luminescence behaviour of Yb{sup 3+}-doped and Yb{sup 3+}-Tb{sup 3+} co-doped strontium aluminates powders: Sr{sub 1-x}Yb{sub x}Al{sub 4}O{sub 7} (x=0.002–0.07) and Sr{sub 1-x-y}Yb{sub x}Tb{sub y}Al{sub 4}O{sub 7} (x=0.03; y=0.002–0.02) were performed. The studies of singly doped samples show that direct excitation of Yb{sup 3+} by means of {sup 2}F{sub 7/2}-{sup 2}F{sub 5/2} absorption at 900–980 nm leads to Stokes Yb{sup 3+} emission in the range of 970–1130 nm as well as bluish-green Yb{sup 3+} cooperative luminescence (CL) whose energy doubles that of the NIR one. The effect of activator concentration and charge compensation through Na{sup +} co-doping on both Yb{sup 3+} emissions were also studied. It was found that Na{sup +} addition enhanced Stokes Yb{sup 3+} photoluminescence brightness, while the cooperative emission intensity appeared to be lower. In doubly Yb{sup 3+}-Tb{sup 3+} doped materials excitation at 980 nm led to cooperative sensitization of the Tb{sup 3+} {sup 5}D{sub 4} level giving rise to its green {sup 5}D{sub 4}→{sup 7}F{sub J} (J={sup 7}F{sub 6}-{sup 7}F{sub 3}) up-conversion luminescence with the dominant component around 542 nm. The cooperative energy transfer (CET) mechanism was proposed basing on the results obtained from emission and absorption spectra, decay kinetics as well as the dependence of UC luminescence intensity on NIR excitation power.

  2. Influence of Yb AND Yb2O3 addition on the properties of InP layers

    Czech Academy of Sciences Publication Activity Database

    Procházková, Olga; Grym, Jan; Zavadil, Jiří; Žďánský, Karel; Lorinčík, Jan

    2008-01-01

    Roč. 10, č. 12 (2008), s. 3261-3264 ISSN 1454-4164 R&D Projects: GA ČR GA102/06/0153; GA ČR(CZ) GP102/08/P617 Institutional research plan: CEZ:AV0Z20670512 Keywords : semiconductor technology * rare earth elements * InP Subject RIV: JA - Electronics ; Optoelectronics, Electrical Engineering Impact factor: 0.577, year: 2008

  3. Optical properties of Mg2+, Yb3+, and Ho3+ tri-doped LiNbO3 crystals

    Science.gov (United States)

    Dai, Li; Liu, Chun-Rui; Tan, Chao; Yan, Zhe-Hua; Xu, Yu-Heng

    2017-04-01

    A series of LiNbO3 crystals tri-doped with Mg{}2+, Yb{}3+, and Ho{}3+ are grown by the conventional Czochraski technique. The concentrations of Mg{}2+, Yb{}3+, and Ho{}3+ ions in Mg:Yb:Ho:LiNbO3 crystals are measured by using an inductively coupled plasma atomic emission spectrometry. The x-ray diffraction is proposed to determine the lattice constant and analyze the internal structure of the crystal. The light-induced scattering of Mg:Yb:Ho:LiNbO3 crystal is quantitatively described via the threshold effect of incident exposure energy flux. The exposure energy ({E}{{r}}) is calculated to discuss the optical damage resistance ability. The exposure energy of Mg(7 mol):Yb:Ho:LiNbO3 crystal is 709.17 J/cm2, approximately 425 times higher than that of the Mg(1 mol):Yb:Ho:LiNbO3 crystal in magnitude. The blue, red, and very intense green bands of Mg:Yb:Ho:LiNbO3 crystal are observed under the 980-nm laser excitation to evaluate the up-conversion emission properties. The dependence of the emission intensity on pumping power indicates that the up-conversion emission is a two-photon process. The up-conversion emission mechanism is discussed in detail. This study indicates that Mg:Yb:Ho:LiNbO3 crystal can be applied to the fabrication of new multifunctional photoluminescence devices. Project supported by the National Natural Science Foundation of China (Grant No. 51301055), the Youth Science Fund of Heilongjiang Province, China (Grant No. QC2015061), the Special Funds of Harbin Innovation Talents in Science and Technology Research, China (Grant No. 2015RQQXJ045 ), and the Science Funds for the Young Innovative Talents of Harbin University of Science and Technology, China (Grant No. 201501).

  4. Luminescent properties of LuAG:Yb and YAG:Yb single crystalline films grown by Liquid Phase Epitaxy method

    International Nuclear Information System (INIS)

    Zorenko, Yu; Zorenko, T.; Gorbenko, V.; Voznyak, T.; Popielarski, P.; Batentschuk, M.; Osvet, A.; Brabec, Ch; Kolobanov, V.; Spasky, D.; Fedorov, A.

    2016-01-01

    In this work, investigation of the spectroscopic parameters of the luminescence of Yb"3"+ ions in single crystalline films of Lu_3Al_5O_1_2 and Y_3Al_5O_1_2 garnets was performed using the synchrotron radiation excitation with the energy in the range of Yb"3"+ charge transitions (CT), exciton range and the onset of interband transitions of these garnets. The basic spectroscopic parameters of the Yb"3"+ CT luminescence in LuAG and YAG hosts were determined and summarized with taking into account the differences in the band gap structure of these garnets. - Highlights: • Single crystalline films of Yb doped LuAG and YAG garnets were grown by LPE method. • Yb"3"+ luminescence of LuAG:Yb and YAG:Yb film were studied using synchrotron radiation. • Basic parameters of Yb"3"+ charge transfer luminescence in LuAG and YAG were determined.

  5. Conversion and quantum efficiency from ultraviolet light to near infrared emission in Yb{sup 3+}-doped pyrovanadates MZnV{sub 2}O{sub 7} (M = Ca, Sr, Ba)

    Energy Technology Data Exchange (ETDEWEB)

    Guan, Ying; Huang, Yanlin [College of Chemistry, Chemical Engineering and Materials Science, Soochow University, Suzhou 215123 (China); Tsuboi, Taiju; Huang, Wei [Jiangsu-Singapore Joint Research Center for Organic/Bio-Electronics and Information Displays and Institute of Advanced Materials, Nanjing Tech University, Nanjing 211816 (China); Chen, Cuili; Cai, Peiqing [Department of Physics and Interdisciplinary Program of Biomedical, Mechanical and Electrical Engineering, Pukyong National University, Busan 608-737 (Korea, Republic of); Seo, Hyo Jin, E-mail: hjseo@pknu.ac.kr [Department of Physics and Interdisciplinary Program of Biomedical, Mechanical and Electrical Engineering, Pukyong National University, Busan 608-737 (Korea, Republic of)

    2014-12-15

    Highlights: • Efficient convertors of Yb{sup 3+} doped pyrovanadates are prepared and characterized. • Broadband down-conversion from ultraviolet into near-infrared is realized. • High quantum efficiency of 18.5% can be reached. • Energy transfer from VO{sub 4} groups to Yb{sup 3+} ions is demonstrated on the base of the crystal structure. - Abstract: Yb{sup 3+}-doped CaZnV{sub 2}O{sub 7}, SrZnV{sub 2}O{sub 7} and BaZnV{sub 2}O{sub 7} were synthesized via the solid-state reaction. The polycrystalline samples were investigated by XRD and SEM measurements. The reflectance spectra, photoluminescence (PL) excitation and emission spectra, the absolute quantum efficiency (QE) of the IR emission (900–1100 nm) were measured. The efficient conversion from ultraviolet (UV) light to near-infrared (NIR) emission has been demonstrated in the Yb{sup 3+}-doped pyrovanadates by the broadband down conversion from VO{sub 4}{sup 3−} to Yb{sup 3+} ions. Under UV light excitation, an intense NIR emission around 1000 nm ascribed to the {sup 2}F{sub 5/2} → {sup 2}F{sub 7/2} transition of Yb{sup 3+} ions has been observed, which just corresponds to the spectral response of Si solar cells. The NIR emission efficiency is observed to depend on the lattice of pyrovanadate. The mechanism of the NIR emission ascribed to energy transfer is discussed by taking into account the experimental results and the crystal structures.

  6. Carrier concentration effects on radiation damage in InP

    International Nuclear Information System (INIS)

    Yamaguchi, M.; Ando, K.; Uemura, C.

    1984-01-01

    Minority carrier diffusion length and carrier concentration studies have been made on room-temperature 1-MeV electron irradiated liquid-encapsulated Czochralski grown Zn-doped p-InP. The damage rate for the diffusion length and carrier removal rate due to irradiation have been found to strongly decrease with an increase in the carrier concentration in InP. These phenomena suggest that the induced defects interact with impurities in InP. A preliminary study on the annealing behavior has also been performed

  7. Hydrothermal synthesis of superparamagnetic and red luminescent bifunctional Fe{sub 3}O{sub 4}@Mn{sup 2+}-doped NaYF{sub 4}:Yb/Er core@shell monodisperse nanoparticles and their subsequent ligand exchange in water

    Energy Technology Data Exchange (ETDEWEB)

    Qin, Zhenli; Du, Sinan; Luo, Yang; Liao, Zhijian; Zuo, Fang, E-mail: polymerzf@swun.cn; Luo, Jianbin; Liu, Dong

    2016-08-15

    Graphical abstract: An efficient hydrothermal method was used to fabricate the superparamagnetic and red luminescent bifunctional Fe{sub 3}O{sub 4}@Mn{sup 2(*)+}-doped NaYF{sub 4}:Yb/Er nanoparticles (NPs) with core@shell structures through a seed-growth procedure. Then using PEG phosphate ligand to displace oleate from the as-synthesized NPs, hydrophilic Fe{sub 3}O{sub 4}@Mn{sup 2+}-doped NaYF{sub 4}:Yb/Er NPs with good water solubility are obtained. - Highlights: • Homogeneous size distribution of magnetic-upconversion core@shell structured nanoparticles (NPs) were synthesized. • The core@shell nanostructures were obtained by seed-growth method. • The oleic acid coated Fe{sub 3}O{sub 4} NPs were used as seeds and cores. • The magnetic-upconversion NPs emitted red luminescence under a 980 nm laser. • Synthesized magnetic-upconversion NPs were phase transferred using ligand exchange process. - Abstract: We report the use of an efficient hydrothermal method to synthesize superparamagnetic and red luminescent bifunctional Fe{sub 3}O{sub 4}@Mn{sup 2+}-doped NaYF{sub 4}:Yb/Er nanoparticles (NPs) with core@shell structures via a seed-growth procedure. Oleic acid coated Fe{sub 3}O{sub 4} (OA-Fe{sub 3}O{sub 4}) NPs were initially synthesized using a coprecipitation method. The as-synthesized OA-Fe{sub 3}O{sub 4} NPs were then used as seeds, on which the red upconversion luminescent shell (Mn{sup 2+}-doped NaYF{sub 4}:Yb/Er) was formed. Furthermore, hydrophobic to hydrophilic surface modification of the Fe{sub 3}O{sub 4}@Mn{sup 2+}-doped NaYF{sub 4}:Yb/Er NPs was achieved via a ligand exchange method where oleic acid was displaced by a PEG phosphate ligand [PEG = poly(ethylene glycol)]. These materials were characterized by means of transmission electron microscopy (TEM), X-ray diffraction (XRD), photoluminescence (PL) spectroscopy, and vibrating sample magnetometry (VSM). The Fe{sub 3}O{sub 4} cores were uniformly coated with a Mn{sup 2+}-doped NaYF{sub 4}:Yb

  8. Systems and methods for advanced ultra-high-performance InP solar cells

    Science.gov (United States)

    Wanlass, Mark

    2017-03-07

    Systems and Methods for Advanced Ultra-High-Performance InP Solar Cells are provided. In one embodiment, an InP photovoltaic device comprises: a p-n junction absorber layer comprising at least one InP layer; a front surface confinement layer; and a back surface confinement layer; wherein either the front surface confinement layer or the back surface confinement layer forms part of a High-Low (HL) doping architecture; and wherein either the front surface confinement layer or the back surface confinement layer forms part of a heterointerface system architecture.

  9. Synthesis and Downconversion Emission Property of Yb2O3:Eu3+ Nanosheets and Nanotubes

    Directory of Open Access Journals (Sweden)

    Chao Qian

    2013-01-01

    Full Text Available Ytterbium oxide (Yb2O3 nanocrystals with different Eu3+ (1%, 2%, 5%, and 10% doped concentrations were synthesized by a facile hydrothermal method, subsequently by calcination at 700°C. The crystal phase, size, and morphology of prepared samples were characterized by X-ray diffraction (XRD and transmission electron microscopy (TEM. The results show that the as-prepared Yb2O3 nanocrystals with sheet- and tube-like shape have cubic phase structure. The Eu3+ doped Yb2O3 nanocrystals were revealed to have good down conversion (DC property and intensity of the DC luminescence can be modified by Eu3+ contents. In our experiment the 1% Eu3+ doped Yb2O3 nanocrystals showed the strongest DC luminescence among the obtained Yb2O3 nanocrystals.

  10. 1-MHz high power femtosecond Yb-doped fiber chirped-pulse amplifier

    Science.gov (United States)

    Hu, Zhong-Qi; Yang, Pei-Long; Teng, Hao; Zhu, Jiang-Feng; Wei, Zhi-Yi

    2018-01-01

    A practical femtosecond polarization-maintaining Yb-doped fiber amplifier enabling 153 fs transform-limited pulse duration with 32 μJ pulse energy at 1 MHz repetition rate corresponding to a peak power of 0.21 GW is demonstrated. The laser system based on chirped-pulse amplification (CPA) technique is seeded by a dispersion managed, nonlinear polarization evolution (NPE) mode-locked oscillator with spectrum bandwidth of 31 nm at 1040 nm and amplified by three fiber pre-amplifying stages and a rod type fiber main amplifying stage. The laser works with beam quality of M2 of 1.3 and power stability of 0.63% (root mean square, RMS) over 24 hours will be stable sources for industrial micromachining, medical therapy and scientific research.

  11. Structural, spectroscopic, and tunable laser properties of Yb3+ -doped NaGd(WO4)2

    Science.gov (United States)

    Cascales, C.; Serrano, M. D.; Esteban-Betegón, F.; Zaldo, C.; Peters, R.; Petermann, K.; Huber, G.; Ackermann, L.; Rytz, D.; Dupré, C.; Rico, M.; Liu, J.; Griebner, U.; Petrov, V.

    2006-11-01

    Single crystals of Yb3+ -doped NaGd(WO4)2 with up to 20mol% ytterbium content have been grown by the Czochralski technique in air or in N2+O2 atmosphere and cooled to room temperature at different rates (4-250°C/h) . Only the noncentrosymmetric tetragonal space group I4¯ accounts for all reflections observed in the single crystal x-ray diffraction analysis. The distortion of this symmetry with respect to the centrosymmetric tetragonal space group I41/a is much lower for crystals cooled at a fast rate. Na+ , Gd3+ , and Yb3+ ions share the two nonequivalent 2b and 2d sites of the I4¯ structure, but Yb3+ (and Gd3+ ) ions are found preferentially in the 2b site. Optical spectroscopy at low (5K) temperature provides additional evidence of the existence of these two sites contributing to the line broadening. The comparison with the F7/22(n) and F5/22(n') Stark energy levels calculated using the crystallographic Yb-O bond distances allows to correlate the experimental optical bands with the 2b and 2d sites. As a novel uniaxial laser host for Yb3+ , NaGd(WO4)2 is characterized also with respect to its transparency, band-edge, refractive indices, and main optical phonons. Continuous-wave Yb3+ -laser operation is studied at room temperature both under Ti:sapphire and diode laser pumping. A maximum slope efficiency of 77% with respect to the absorbed power is achieved for the π polarization by Ti:sapphire laser pumping in a three-mirror cavity with Brewster geometry. The emission is tunable in the 1014-1079nm spectral range with an intracavity Lyot filter. Passive mode locking of this laser produces 120fs long pulses at 1037.5nm with an average power of 360mW at ≈97MHz repetition rate. Using uncoated samples of Yb:NaGd(WO4)2 at normal incidence in simple two-mirror cavities, output powers as high as 1.45W and slope efficiencies as high as 51% are achieved with different diode laser pump sources.

  12. Infrared to visible upconversion luminescence in Er3+/Yb3+ co-doped CeO2 inverse opal

    International Nuclear Information System (INIS)

    Yang, Zhengwen; Wu, Hangjun; Liao, Jiayan; Li, Wucai; Song, Zhiguo; Yang, Yong; Zhou, Dacheng; Wang, Rongfei; Qiu, Jianbei

    2013-01-01

    Highlights: • UC emission of Er 3+ was modified by introducing the structure of inverse opal. • Color tuning of CeO 2 :Yb, Er inverse opal was realized by inhibition of UC emission. • Two-photon excitation processes were observed in CeO 2 :Yb, Er inverse opal. -- Abstract: Infrared to visible upconversion luminescence has been investigated in Er 3+ /Yb 3+ co-doped CeO 2 inverse opal. Under the excitation of 980 nm diode lasers, visible emissions centered at 525, 547, 561, 660 and 680 nm are observed, which are assigned to the Er 3+ transitions of 2 H 11/2 → 4 I 15/2 (525 nm), 4 S 3/2 → 4 I 15/2 (547, 561 nm), 4 F 9/2 → 4 I 15/2 (660 and 680 nm), respectively. The effect of photonic band gap on the upconversion luminescence intensity was also obtained. Additionally, the upconversion luminescence mechanism was studied. The dependence of Er 3+ upconversion emission intensity on pump power reveals that it is a two-photon excitation process

  13. Upconversion luminescence of Er3+/Yb3+ doped Sr5(PO4)3OH phosphor powders

    Science.gov (United States)

    Mokoena, P. P.; Swart, H. C.; Ntwaeaborwa, O. M.

    2018-04-01

    Sr5(PO4)3OH co-doped with Er3+and Yb3+ powder phosphors were synthesized by urea combustion method. The crystal structure was analyzed using X-ray diffraction (XRD). Particle morphology was analyzed using a Jeol JSM 7800F thermal field emission scanning electron microscope (FE-SEM) and the chemical composition analysis was carried out using an Oxford Instruments AzTEC energy dispersive spectrometer (EDS) attached to the FE-SEM. Upconversion emission was measured by using a FLS980 Spectrometer equipped with a 980 nm NIR laser as the excitation source, and a photomultiplier (PMT) detector. The XRD data of the Sr5(PO4)3OH powder exhibited characteristic diffraction patterns of the hexagonal structure referenced in the standard JCPDS card number 00-033-1348. The sharp peaks revealed the formation of crystalline Sr5(PO4)3OH. The powders were made up of hexagonal nanospheres. The enhanced red emission due to the 4F9/2 → 4I15/2 transitions of Er3+ was observed and was attributed to up conversion (UC) energy transfer from Yb3+. The upconversion energy transfer mechanism from Yb3+ to Er3+ is discussed.

  14. Thermal conductivity of InAs quantum dot stacks using AlAs strain compensating layers on InP substrate

    International Nuclear Information System (INIS)

    Salman, S.; Folliot, H.; Le Pouliquen, J.; Chevalier, N.; Rohel, T.; Paranthoën, C.; Bertru, N.; Labbé, C.; Letoublon, A.; Le Corre, A.

    2012-01-01

    Highlights: ► The thermal conductivity of InAs on InP (1 1 3)B quantum dots stacks is measured. ► The growth of a close stack of 100 layers of InAs using AlAs strain compensating layers is presented. ► New data on the thermal conductivity of InP n-doped susbtrate are given. - Abstract: The growth and thermal conductivity of InAs quantum dot (QD) stacks embedded in GaInAs matrix with AlAs compensating layers deposited on (1 1 3)B InP substrate are presented. The effect of the strain compensating AlAs layer is demonstrated through Atomic Force Microscopy (AFM) and X-ray diffraction structural analysis. The thermal conductivity (2.7 W/m K at 300 K) measured by the 3ω method reveals to be clearly reduced in comparison with a bulk InGaAs layer (5 W/m K). In addition, the thermal conductivity measurements of S doped InP substrates and the SiN insulating layer used in the 3ω method in the 20–200 °C range are also presented. An empirical law is proposed for the S doped InP substrate, which slightly differs from previously presented results.

  15. Ultrathin film, high specific power InP solar cells on flexible plastic substrates

    International Nuclear Information System (INIS)

    Shiu, K.-T.; Zimmerman, Jeramy; Wang Hongyu; Forrest, Stephen R.

    2009-01-01

    We demonstrate ultrathin-film, single-crystal InP Schottky-type solar cells mounted on flexible plastic substrates. The lightly p-doped InP cell is grown epitaxially on an InP substrate via gas source molecular beam epitaxy. The InP substrate is removed via selective chemical wet-etching after the epitaxial layers are cold-welded to a 25 μm thick Kapton sheet, followed by the deposition of an indium tin oxide top contact that forms the Schottky barrier with InP. The power conversion efficiency under 1 sun is 10.2±1.0%, and its specific power is 2.0±0.2 kW/kg. The ultrathin-film solar cells can tolerate both tensile and compressive stress by bending over a <1 cm radius without damage.

  16. Biocompatible Er, Yb co-doped fluoroapatite upconversion nanoparticles for imaging applications

    Science.gov (United States)

    Anjana, R.; K. M., Kurias; M. K., Jayaraj

    2017-08-01

    Upconversion luminescence, visible emission on infra red (IR) excitation was achieved in a biocompatible material, fluoroapatite. Fluoroapatite crystals are well known biomaterials, which is a component of tooth enamel. Also it can be considered as an excellent host material for lanthanide doping since the ionic radii of lanthanide is similar to that of calcium ion(Ca2+) hence successful incorporation of dopants within the lattice is possible. Erbium (Er), Ytterbium (Yb) co-doped fluorapatite (FAp) nanoparticles were prepared by precipitation method. The particles show intense visible emission when excited with 980 nm laser. Since upconversion luminescence is a multiphoton process the excitation power dependence on emission will give number of photons involved in the emission of single photon. Excitation power dependence studies show that two photons are involved in the emission of single photons. The value of slope was different for different emission peak because of the difference in intermediate energy level involved. The crystal structure and morphology of the particle were determined using X-ray diffractometer (XRD) and field emission scanning electron microscope (FESEM). These particles with surface functionalisation can be used for live cell imaging.

  17. Electron spin resonance in Yb-based Kondo-lattice systems; Elektronenspinresonanz in Yb-basierten Kondogitter-Systemen

    Energy Technology Data Exchange (ETDEWEB)

    Wykhoff, Jan

    2010-07-07

    The systems Yb{sub 1-w}A{sub 1-w}(Rh{sub 1-x}Co{sub x})(Si{sub 1-y}Ge{sub y}){sub 2} with A=La respectively Lu, as well as YbIr{sub 2}Si{sub 2} are studied. The measurements are presented sortedly for systems, dopings, and external parameters. Beside these external parameters furthermore the orientation of the sample related to the quasistatic magnetic field and the microwave magnetic field was varied.

  18. Thermoluminescence and optically stimulated luminescence properties of nanocrystalline Er3+ and Yb3+ doped Y3Al5O12 exposed to β-rays

    International Nuclear Information System (INIS)

    RodrIguez, R A; Rosa, E de la; Salas, P; Melendrez, R; Barboza-Flores, M

    2005-01-01

    The thermoluminescence (TL) and optically stimulated luminescence (OSL) characterization of Er 3+ and Yb 3+ doped Y 3 Al 5 O 12 nanocrystalline samples prepared by the precipitation process and exposed to β-rays are discussed. The TL as well as the OSL were two orders of magnitude higher in Er 3+ doped than in Yb 3+ specimens. The charge trapping and the radiative thermally stimulated recombination processes in Y 3 Al 5 O 12 : Er 3+ involve four trapping states at 166, 243, 342 and 424 deg. C, but just two trapping levels at 219 and 413 deg. C for Y 3 Al 5 O 12 : Yb 3+ at a heating rate of 10 deg. C s -1 . The photostimulation with 470 nm light causes in both phosphors a radiative recombination of the optically free charge carriers belonging to the same trapping states. The TL and the OSL as a function of radiation dose behaviour were linear in the 10-100 Gy dose range. The results provide evidence of the potential uses of these materials in radiation storage and dosimeter devices

  19. Sol-Gel Derived Active Material for Yb Thin-Disk Lasers.

    Science.gov (United States)

    Almeida, Rui M; Ribeiro, Tiago; Santos, Luís F

    2017-09-02

    A ytterbium doped active material for thin-disk laser was developed based on aluminosilicate and phosphosilicate glass matrices containing up to 30 mol% YbO 1.5 . Thick films and bulk samples were prepared by sol-gel processing. The structural nature of the base material was assessed by X-ray diffraction and Raman spectroscopy and the film morphology was evidenced by scanning electron microscopy. The photoluminescence (PL) properties of different compositions, including emission spectra and lifetimes, were also studied. Er 3+ was used as an internal reference to compare the intensities of the Yb 3+ PL peaks at ~ 1020 nm. The Yb 3+ PL lifetimes were found to vary between 1.0 and 0.5 ms when the Yb concentration increased from 3 to 30 mol%. Based on a figure of merit, the best active material selected was the aluminosilicate glass composition 71 SiO₂-14 AlO 1.5 -15 YbO 1.5 (in mol%). An active disk, ~ 36 μm thick, consisting of a Bragg mirror, an aluminosilicate layer doped with 15 mol% Yb and an anti-reflective coating, was fabricated.

  20. Optical properties of Sulfur doped InP single crystals

    Science.gov (United States)

    El-Nahass, M. M.; Youssef, S. B.; Ali, H. A. M.

    2014-05-01

    Optical properties of InP:S single crystals were investigated using spectrophotometric measurements in the spectral range of 200-2500 nm. The absorption coefficient and refractive index were calculated. It was found that InP:S crystals exhibit allowed and forbidden direct transitions with energy gaps of 1.578 and 1.528 eV, respectively. Analysis of the refractive index in the normal dispersion region was discussed in terms of the single oscillator model. Some optical dispersion parameters namely: the dispersion energy (Ed), single oscillator energy (Eo), high frequency dielectric constant (ɛ∞), and lattice dielectric constant (ɛL) were determined. The volume and the surface energy loss functions (VELF & SELF) were estimated. Also, the real and imaginary parts of the complex conductivity were calculated.

  1. Growth of Yb3+-doped Y2O3 single crystal rods by the micro-pulling-down method

    International Nuclear Information System (INIS)

    Mun, J.H.; Novoselov, A.; Yoshikawa, A.; Boulon, G.; Fukuda, T.

    2005-01-01

    The rare-earth sesquioxides (RE 2 O 3 , RE = Lu, Y and Sc) are very promising host crystals for advanced laser diode (LD)-pumped Yb 3+ -doped solid-state lasers due to unusual combination, almost unique of favourable structural, thermal and spectroscopic properties which are described. In spite of these favourable properties, the bulk single crystal growth technology for the rare-earth sesquioxides has not been established yet. The extremely high melting temperature at around 2400 deg. C has prevented it. However, we shall show that yttrium oxide crystals (Yb x Y 1-x ) 2 O 3 , x = 0.0, 0.005, 0.05, 0.08 and 0.15 of cylindrical shape as laser rods with 4.2 mm in diameter and 15-20 mm in length have been grown from rhenium crucibles by the micro-pulling-down method. The crystal quality characterisation of undoped Y 2 O 3 crystal was determined using X-ray rocking curve (XRC) analysis. Yb were homogeneously distributed in Y 2 O 3 host crystal

  2. Infrared emissions in MgSrAl10O17:Er3+ phosphor co-doped with Yb3+/Ba2+/Ca2+ obtained by solution combustion route

    International Nuclear Information System (INIS)

    Singh, Vijay; Kumar Rai, Vineet; Venkatramu, V.; Chakradhar, R.P.S.; Hwan Kim, Sang

    2013-01-01

    An intense infrared emitting MgSrAl 10 O 17 :Er 3+ phosphor co-doped with Yb 3+ , Ba 2+ and Ca 2+ ions have been prepared by a solution combustion method. Phase purity of the derived compounds was confirmed by X-ray diffraction technique. The vibrational properties of MgSrAl 10 O 17 phosphor was studied by Fourier transform infrared spectroscopy. The broad and strong infrared emission of Er 3+ ions at around 1.53 μm was observed upon excitation at 980 nm. Effect of co-doping with the Yb 3+ , Ba 2+ and Ca 2+ ions on the infrared luminescence intensity of Er 3+ ions and the mechanism responsible for the variation in the infrared intensity have been discussed. The results indicate that these materials may be suitable for the optical telecommunication window and wavelength division multiplexing applications. - Highlights: ► The hexagonal phase of MgSrAl 10 O 17 could be obtained by the low temperature combustion method. ► The broad and strong infrared emission of Er 3+ ions at around 1.53 μm was observed. ► Effect of co-doping with the Yb 3+ , Ba 2+ and Ca 2+ ions on the infrared luminescence intensity of Er 3+ were reported.

  3. Energy transfer processes in Yb{sup 3+}-Tm{sup 3+} co-doped sodium alumino-phosphate glasses with improved 1.8 {mu}m emission

    Energy Technology Data Exchange (ETDEWEB)

    Camargo, Andrea S S de; Terra, Idelma A A; Nunes, Luiz Antonio de O; Li, M Siu [Instituto de Fisica de Sao Carlos, Universidade de Sao Paulo, 13560-970, Sao Carlos-SP (Brazil)], E-mail: andreasc@ifsc.usp.br

    2008-06-25

    Sodium alumino-phosphate glasses co-doped with Yb{sup 3+} and Tm{sup 3+} ions have been prepared with notably low OH{sup -} content, and characterized from the viewpoint of their spectroscopic properties. In these glasses, Yb{sup 3+} acts as an efficient sensitizer of excitation energy at 0.98 {mu}m-which can be provided by high power and low cost diode lasers, and subsequently undergoes non-resonant energy transfer to Tm{sup 3+} ions ({sup 2}F{sub 5/2}, {sup 3}H{sub 6} {yields} {sup 2}F{sub 7/2}, {sup 3}H{sub 5}). Through this process, the emitting level {sup 3}F{sub 4} is rapidly populated, generating improved emission at 1.8 {mu}m ({sup 3}F{sub 4} {yields} {sup 3}H{sub 6}). In order to guarantee the efficiency of such favorable energy transfer, energy losses via multiphonon decay, Yb-Yb radiative trapping, and non-radiative transfer to OH{sup -} groups were evaluated, and minimized when possible. The dipole-dipole energy transfer microscopic parameters corresponding to Yb{sup 3+} {yields} Tm{sup 3+}, Yb{sup 3+} {yields} Yb{sup 3+} and Tm{sup 3+} {yields} Tm{sup 3+} transfers, calculated by the Foerster-Dexter model, are C{sub Yb-Tm} = 2.9 x 10{sup -40} cm{sup 6} s{sup -1}, C{sub Yb-Yb} = 42 x 10{sup -40} cm{sup 6} s{sup -1} and C{sub Tm-Tm} = 43 x 10{sup -40} cm{sup 6} s{sup -1}, respectively.

  4. Yb3+ sensitized Tm3+ upconversion in tellurite lead oxide glass.

    Science.gov (United States)

    Mohanty, Deepak Kumar; Rai, Vineet Kumar; Dwivedi, Y

    2012-04-01

    Triply ionized thulium/thulium--ytterbium doped/codoped TeO2-Pb3O4 (TPO) glasses have been fabricated by classical quenching method. The upconversion emission spectra in the Tm3+/Tm3+-Yb3+ doped/codoped glasses upon excitation with a diode laser lasing at ∼980 nm has been studied. Effect of the addition of the Yb3+ on the upconversion emission intensity in the visible and near infrared regions of the Tm3+ doped in TPO glass has been studied and the processes involved explored. Copyright © 2011 Elsevier B.V. All rights reserved.

  5. Spectral and laser properties of Er3+/Yb3+/Ce3+ tri-doped Ca3NbGa3Si2O14 crystal at 1.55 µm

    Science.gov (United States)

    Gong, Guoliang; Chen, Yujin; Lin, Yanfu; Huang, Jianhua; Gong, Xinghong; Luo, Zundu; Huang, Yidong

    2018-04-01

    An Er3+/Yb3+/Ce3+ tri-doped Ca3NbGa3Si2O14 (CNGS) crystal was grown by the Czochralski method. Spectral properties of the crystal, including the polarized absorption and fluorescence spectra, the fluorescence decay, as well as the energy transfer efficiency from Yb3+ to Er3+ were investigated in detail. End-pumped by a 976 nm diode laser, a 1556 nm continuous-wave laser with a maximum output power of 202 mW and a slope efficiency of 11.4% was achieved in the Er,Yb,Ce:CNGS crystal. The results indicate the Er,Yb,Ce:CNGS crystal is a promising 1.55 µm laser gain medium.

  6. Spatially selective Er/Yb-doped CaF2 crystal formation by CO2 laser exposure

    International Nuclear Information System (INIS)

    Kim, Dong-Seon; Lee, Jin-Ho; Lim, Ki-Soo

    2014-01-01

    Highlights: • Oxyfluoride glass–ceramics containing CaF 2 nanocrystals doped with Er 3+ and Yb 3+ ions were formed on the glass surface by CO 2 laser and a heat gun exposure. • Most of Er and Yb ions were distributed inside CaF 2 nanocrystals and fluorine loss was observed in the EDS element maps. • IR-to-VIS upconversion emission efficiency of laser annealed glass ceramics was much increased and compared with that of the furnace-annealed glass ceramics. • Distributed volume of the glass ceramics were estimated by a confocal fluorescence microscope imaging. - Abstract: We report the glass–ceramic precipitation on the oxyfluoride glass surface by spatially selective annealing with a CO 2 laser and a heat gun exposure. X-ray diffraction analysis showed the formation of major CaF 2 and miner Ca 2 SiO 4 nanoparticles. We observed ∼100 nm nanoparticle aggregation by tunneling electron microscopy and element distribution in glass and crystal phases. Spatial distribution of glass ceramics near the glass surface was probed by confocal fluorescence microscope by using much enhanced emission from the Er ions in the laser-treated area. Strong emissions at 365 nm excitation and visible up-conversion emissions at 980 nm excitation also indicated well incorporation of Er and Yb ions into a crystalline environment

  7. Spatially selective Er/Yb-doped CaF2 crystal formation by CO2 laser exposure

    International Nuclear Information System (INIS)

    Kim, Dong-Seon; Lee, Jin-Ho; Lim, Ki-Soo

    2015-01-01

    Highlights: • Oxyfluoride glass–ceramics containing CaF 2 nanocrystals doped with Er 3+ and Yb 3+ ions were formed on the glass surface by CO 2 laser and a heat gun exposure. • Most of Er and Yb ions were distributed inside CaF 2 nanocrystals and fluorine loss was observed in the EDS element maps. • IR-to-VIS upconversion emission efficiency of laser annealed glass ceramics was much increased and compared with that of the furnace-annealed glass ceramics. • Distributed volume of the glass ceramics were estimated by a confocal fluorescence microscope imaging. - Abstract: We report the glass–ceramic precipitation on the oxyfluoride glass surface by spatially selective annealing with a CO 2 laser and a heat gun exposure. X-ray diffraction analysis showed the formation of major CaF 2 and miner Ca 2 SiO 4 nanoparticles. We observed ∼100 nm nanoparticle aggregation by tunneling electron microscopy and element distribution in glass and crystal phases. Spatial distribution of glass ceramics near the glass surface was probed by confocal fluorescence microscope by using much enhanced emission from the Er ions in the laser-treated area. Strong emissions at 365 nm excitation and visible up-conversion emissions at 980 nm excitation also indicated well incorporation of Er and Yb ions into a crystalline environment

  8. Characterization and Computation of Yb/TiO2 and Its Photocatalytic Degradation with Benzohydroxamic Acid

    Directory of Open Access Journals (Sweden)

    Xianping Luo

    2017-11-01

    Full Text Available Yb-doped TiO2 (Yb/TiO2 compositions were synthesized by sol-gel method, and the prepared materials were characterized by X-ray Diffraction (XRD, X-ray photoelectron spectroscopy (XPS, UV-visible diffuse-reflectance spectrum (UV-Vis DRS, transmission electron microscope (TEM and high resolution transmission electron microscope (HRTEM, energy dispersive spectrometer (EDS, and N2 adsorption. A beneficiation reagent of benzohydroxamic acid (BHA was used to test the photocatalytic activity of Yb/TiO2. The characterizations indicate that the doping of Yb could inhibit the crystal growth of TiO2, enhance the specific surface area, increase the binding energy of Ti2p, and also slightly expand the adsorption ranges to visible light. Furthermore, the computation of band structure also indicates that Yb-doped TiO2 could make the forbidden band narrower than pure anatase TiO2, which presents a red shift in the absorption spectrum. As a result of the photodegradation experiment on BHA, Yb/TiO2 (0.50% in mass sintered at 450 °C displayed the highest catalytic activity for BHA when compared with pure TiO2 or other doped Yb/TiO2 compositions, and more than 89.2% of the total organic carbon was removed after 120 min. Almost all anions, including Cl−, HCO3−, NO3−, and SO42−, inhibited the degradation of BHA by Yb/TiO2, and their inhibition effects followed the order of HCO3− > NO3− > SO42− > Cl−. Cations of Na+, K+, Ca2+, and Mg2+ displayed a slight suppressing effect due to the impact of Cl− coexisting in the solution. In addition, Yb/TiO2 maintained a high photocatalytic ability with respect to BHA after four runs. It is hypothesized that ·OH is one of the main species involved in the photodegradation of BHA, and the mutual transformation of Yb3+ and Yb2+ could promote the separation of electron-hole pairs.

  9. Spectral properties and laser performances of Yb3+:LaCa4O(BO3)3 crystal with high concentration doping

    International Nuclear Information System (INIS)

    Ji, Yuexia; Cao, Jiafeng; Xu, Jinlong; You, Zhenyu; Zhu, Zhaojie; Li, Jianfu; Wang, Yan; Tu, Chaoyang

    2013-01-01

    Highlights: •Yb 3+ :LaCa 4 O(BO 3 ) 3 single crystal was grown with high concentration doping. •Laser potentiality was evaluated based on the spectral and laser parameters. •Continuous wave laser operation was realized. •An output power of 0.77 W and a slope efficiency of 15.71% at 1077 nm were obtained. •The spectra and laser properties of Yb 3+ :LaCa 4 O(BO 3 ) 3 crystal were firstly reported. -- Abstract: High concentration of 15 at.% Yb 3+ doped LaCa 4 O(BO 3 ) 3 (LaCOB) crystal was grown by Czochralski technique. The absorption cross section was conclulated to be 0.63 × 10 −20 cm 2 at 977 nm and the emission cross section to be 0.39 × 10 −20 cm 2 at 1030 nm, with the FWHM of 6.15 and 33 nm respectively. Laser potentiality was evaluated based on the gain cross section σ g , the minimum inversion fraction β min and the minimum pump intensity I min , which were calculated to be 0.18 × 10 −20 cm 2 , 0.05 and 0.47 kw/cm 2 , respectively. Continuous wave laser operation was realized with an output power of 0.77 W and a slope efficiency of 15.71%. The laser emitted around 1077 nm. The radiation trapping and continuous pump mode are contributed to the lasing wavelength for present crystal

  10. Yb-doped phosphate double-cladding optical fiber for high-power laser applications

    Science.gov (United States)

    Mura, E.; Scarpignato, G. C.; Lousteau, J.; Boetti, N. G.; Abrate, S.; Milanese, D.

    2013-02-01

    A Yb-doped phosphate glass double cladding optical fiber was prepared using a custom designed glass composition (P2O5 - Al2O3 - Li2O - B2O3 - BaO - PbO - La2O3) for high-power amplifier and laser applications. The preform drawing method was followed, with the preform being fabricated using the rotational casting technique. This technique, previously developed for tellurite, fluoride or chalcogenide glass preforms is reported for the first time using rare earth doped phosphate glasses. The main challenge was to design an adequate numerical aperture between first and second cladding while maintaining similar thermo-mechanical properties in view of the fiber drawing process. The preform used for the fiber drawing was produced by rod-in-tube technique at a rotation speed of 3000 rpm. The rotational casting technique allowed the manufacturing of an optical fiber featuring high quality interfaces between core and internal cladding and between the internal and external cladding, respectively. Loss attenuation was measured using the cut-back method and lasing was demonstrated at 1022 nm by core pumping with a fiber pigtailed laser diode at the wavelength of 976 nm.

  11. Effect of Fe inter-diffusion on properties of InP layers grown with addition of RE elements

    International Nuclear Information System (INIS)

    Prochazkova, O.; Zavadil, J.; Zdansky, K.

    2005-01-01

    This contribution reports the redistribution behaviour of Fe during the growth of InP layers from liquid phase with addition of some rare earth elements on semi-insulating InP:Fe substrates. We have studied the influence of different rare earths on the Fe diffusion into InP layer and compared it with the phenomenon of an extraction of iron from Fe doped materials into adjacent layers doped by Zn, Cd and Be, reported recently. In the case of Tm addition a conversion of electrical conductivity of InP layer to semi-insulating as a consequence of Fe diffusion has been observed while no significant Fe inter-diffusion has been confirmed in the presence of other investigated rare earth additions. (copyright 2005 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

  12. InP tunnel junction for InGaAs/InP tandem solar cells

    Science.gov (United States)

    Vilela, M. F.; Freundlich, A.; Bensaoula, A.; Medelci, N.; Renaud, P.

    1995-01-01

    Chemical beam epitaxy (CBE) has been shown to allow the growth of high quality materials with reproducible complex compositional and doping profiles. The main advantage of CBE compared to metalorganic chemical vapor deposition (MOCVD), the most popular technique for InP-based photovoltaic device fabrication, is the ability to grow high purity epilayers at much lower temperatures (450-530 C). We have previously shown that CBE is perfectly suited toward the fabrication of complex photovoltaic devices such as InP/InGaAs monolithically integrated tandem solar cells, because its low process temperature preserves the electrical characteristics of the InGaAs tunnel junction commonly used as an ohmic interconnect. In this work using CBE for the fabrication of optically transparent (with respect to the bottom cell) InP tunnel diodes is demonstrated. Epitaxial growth were performed in a Riber CBE 32 system using PH3 and TMIn as III and V precursors. Solid Be (p-type) and Si (n-type) have been used as doping sources, allowing doping levels up to 2 x 10(exp -19)/cu cm and 1 x 10(exp -19)/cu cm for n and p type respectively. The InP tunnel junction characteristics and the influence of the growth's conditions (temperature, growth rate) over its performance have been carefully investigated. InP p(++)/n(++) tunnel junction with peak current densities up to 1600 A/sq cm and maximum specific resistivities (V(sub p)/I(sub p) - peak voltage to peak current ratio) in the range of 10(exp -4) Omega-sq cm were obtained. The obtained peak current densities exceed the highest results previously reported for their lattice matched counterparts, In(0.53)Ga( 0.47)As and should allow the realization of improved minimal absorption losses in the interconnect InP/InGaAs tandem devices for Space applications. Owing to the low process temperature required for the top cell, these devices exhibit almost no degradation of its characteristics after the growth of subsequent thick InP layer suggesting

  13. Multielement (P-Yb-Zr-Ce-Al-Ca) fiber for moderate-power laser application with enhanced photodarkening resistivity

    Energy Technology Data Exchange (ETDEWEB)

    Dhar, Anirban; Paul, Mukul Chandra [CSIR-Central Glass and Ceramic Research Institute, 196 Raja S. C. Mullick Road, Jadavpur, Kolkata 700 032 (India); Das, Shyamal; Reddy, Pinninty Harshavardhan; Siddiki, Salim H.; Dutta, Debjit; Pal, Mrinmay [Academy of Scientific and Innovative Research (AcSIR), CSIR-CGCRI Campus, Kolkata 700 032 (India); Kir' yanov, Alexander V. [Centro de Investigaciones en Optica, Loma del Bosque 115, Col. Lomas del Campestre, Leon 37150, Guanajuato (Mexico)

    2017-06-15

    Multielement (ME) (P-Yb-Zr-Ce-Al-Ca) nanophase separated silica-glass-based optical fiber is fabricated through a conventional-modified chemical vapor deposition (MCVD) process, coupled with solution doping technique. The lasing and photodarkening behaviors of this ME fiber have been demonstrated and compared, in terms of its photodarkening (PD) performance at moderate pump powers (tens of Watts), with standard Yb-doped fiber with phospho-alumino-silicate (PAS) glass composition, which clearly reveals that the ME-Yb doped fiber is a promising candidate for laser applications with enhanced PD resistivity. (copyright 2017 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  14. Up conversion luminescence of Yb3+–Er3+ codoped CeO2 nanocrystals with imaging applications

    International Nuclear Information System (INIS)

    Cho, Jung-Hyun; Bass, Michael; Babu, Suresh; Dowding, Janet M.; Self, William T.; Seal, Sudipta

    2012-01-01

    The effects of Yb 3+ doping on up conversion in Yb 3+ –Er 3+ co-doped cerium oxide nanocrystals are reported. Green emission around 545 and 560 nm attributed to the 2 H 11/2 , 4 S 3/2 → 4 I 15/2 transitions and red emission around 660 and 680 nm due to 4 F 9/2 → 4 I 15/2 transitions under 975 nm excitation were studied at room temperature. Both green and red emission intensities increase as the Yb 3+ concentration increases from 0%. Emission strength starts to decrease after the Yb 3+ concentration exceeds a critical amount. The green emission strength peaks around 1% Yb 3+ concentration while the red emission strength peaks around 4%. An explanation of competition between different decay mechanisms is presented to account for the luminescence dependence on Yb 3+ concentration. Also, the application of up converting nanoparticles in biomedical imaging is demonstrated. - Highlights: ► Up conversion in Yb 3+ –Er 3+ co-doped cerium oxide nanocrystals. ► Different decay mechanisms determine luminescence efficiency. ► Up converting nanoparticles in biomedical imaging is demonstrated.

  15. Multifunctional Eu3+- and Er3+/Yb3+-doped GdVO4 nanoparticles synthesized by reverse micelle method

    OpenAIRE

    Gavrilović, Tamara V.; Jovanović, Dragana J.; Lojpur, Vesna; Dramićanin, Miroslav D.

    2014-01-01

    Synthesis of Eu3+- and Er3+/Yb3+-doped GdVO4 nanoparticles in reverse micelles and their multifunctional luminescence properties are presented. Using cyclohexane, Triton X-100, and n-pentanol as the oil, surfactant, and co-surfactant, respectively, crystalline nanoparticles with ~4 nm diameter are prepared at low temperatures. The particle size assessed using transmission electron microscopy is similar to the crystallite size obtained from X-ray diffraction measurements, suggesting that each ...

  16. Characterization of the lasing properties of a 5%Yb doped Lu.sub.2./sub.SiO.sub.5./sub. crystal along its three optical axes

    Czech Academy of Sciences Publication Activity Database

    Toci, G.; Pirri, A.; Beitlerová, Alena; Shoji, Y.; Yoshikawa, A.; Hybler, Jiří; Nikl, Martin; Vannini, M.

    2015-01-01

    Roč. 23, č. 10 (2015), s. 13210-13221 ISSN 1094-4087 Institutional support: RVO:68378271 Keywords : Lu 2 SiO 5 * Yb-doped * laser Subject RIV: BH - Optics, Masers, Lasers Impact factor: 3.148, year: 2015

  17. Growth and continuous-wave laser operation of disordered crystals of Yb3+:NaLa(WO4)2 and Yb3+:NaLa(MoO4)2

    Science.gov (United States)

    Liu, J.; Cano-Torres, J. M.; Cascales, C.; Esteban-Betegón, F.; Serrano, M. D.; Volkov, V.; Zaldo, C.; Rico, M.; Griebner, U.; Petrov, V.

    2005-03-01

    Single crystals of disordered NaLa(WO4)2 and NaLa(MoO4)2 doped with Yb3+ are grown by the Czochralski method from the melt. Continuous-wave laser operation with Ti:sapphire laser pumping is demonstrated at room temperature without special cooling. Tunability from 1017 to 1057 nm and from 1015 to 1053 nm is achieved for Yb:NaLa(WO4)2 and Yb:NaLa(MoO4)2, respectively. A maximum output power of 205 mW is obtained with Yb:NaLa(WO4)2.

  18. Single n+-i-n+ InP nanowires for highly sensitive terahertz detection.

    Science.gov (United States)

    Peng, Kun; Parkinson, Patrick; Gao, Qian; Boland, Jessica L; Li, Ziyuan; Wang, Fan; Mokkapati, Sudha; Fu, Lan; Johnston, Michael B; Tan, Hark Hoe; Jagadish, Chennupati

    2017-03-24

    Developing single-nanowire terahertz (THz) electronics and employing them as sub-wavelength components for highly-integrated THz time-domain spectroscopy (THz-TDS) applications is a promising approach to achieve future low-cost, highly integrable and high-resolution THz tools, which are desirable in many areas spanning from security, industry, environmental monitoring and medical diagnostics to fundamental science. In this work, we present the design and growth of n + -i-n + InP nanowires. The axial doping profile of the n + -i-n + InP nanowires has been calibrated and characterized using combined optical and electrical approaches to achieve nanowire devices with low contact resistances, on which the highly-sensitive InP single-nanowire photoconductive THz detectors have been demonstrated. While the n + -i-n + InP nanowire detector has a only pA-level response current, it has a 2.5 times improved signal-to-noise ratio compared with the undoped InP nanowire detector and is comparable to traditional bulk THz detectors. This performance indicates a promising path to nanowire-based THz electronics for future commercial applications.

  19. Red, green, blue and white light upconversion emission in Yb3+/Tm3+/Ho3+ co-doped tellurite glasses

    International Nuclear Information System (INIS)

    Desirena, H; De la Rosa, E; Meza, O; Salas, P

    2011-01-01

    Several Yb 3+ /Tm 3+ /Ho 3+ co-doped transparent TeO 2 -ZnO-Na 2 O-Yb 2 O 3 -Ho 2 O 3 -Tm 2 O 3 glasses were prepared and luminescence properties were characterized. Simultaneous red, green and blue (RGB) emission were obtained after excitation at 970 nm. Colour emission was tuned from multicolour to white light with colour coordinate (0.32, 0.33) matching very well with the white reference (0.33, 0.33). Changes in colour emission were obtained by varying the intensity ratios between RGB bands that are strongly concentration dependent because of the interaction of co-dopants. The colour tunability, high quality of white light and high intensity of the emitted signal make these transparent glasses excellent candidates for applications in solid-state lighting.

  20. Spin reorientation behavior in Yb doped YMnO3

    International Nuclear Information System (INIS)

    Sharma, Neetika; Das, A.

    2014-01-01

    RMnO 3 with smaller rare-earths ions (R = Ho to Lu and Y) crystallize in the non-centrosymmetric hexagonal space group P6 3 cm. The magnetic structure of RMnO 3 compounds with (R=Er,Yb.Lu) are described by irreducible representations (IR) Γ 2,4 and Γ 1,3 for those with higher ionic radii (R=Ho,Y,Y-Er). Of recent the magnetic structure of YMnO 3 has been found to be better described by Γ 3 + Γ 4 IR. YbMnO 3 is another hexagonal manganite, with almost similar transition temperature, and basically shares all the physical properties of YMnO 3 , except for the magnetic structure. The magnetic structure of YbMnO 3 can be explained by Γ 2 or Γ 4 . The non collinear nature of magnetic ordering in these compounds arises due to the frustration inherent in these compounds. In this study we have probed the effect of a magnetic ion (Yb) on the magnetic structure of these frustrated isostructural compounds

  1. Spectral-converting behaviors of Er{sup 3+} and Er{sup 3+}–Yb{sup 3+} doped YOCl phosphors

    Energy Technology Data Exchange (ETDEWEB)

    Park, Sangmoon, E-mail: spark@silla.ac.kr [Center for Green Fusion Technology and Department of Engineering in Energy and Applied Chemistry, Silla University, Busan 617-736 (Korea, Republic of); Cho, So-Hye [Center for Materials Architecturing, Institute of Multidisciplinary Convergence of Materials, Korea Institute of Science and Technology, Seoul 130-650 (Korea, Republic of)

    2014-01-25

    Highlights: • Luminescent materials of YOCl:Er,Yb were prepared using NH{sub 4}Cl flux. • Interesting spectral-converting behaviors were observed in the phosphors. • 980 or 1550 nm diode laser was irradiated for up-converting study. • A multi-photon process in the phosphors was calculated. -- Abstract: Luminescent materials composed of Y{sub 1−m−n}Er{sub m}Yb{sub n}OCl (m = 0.001–0.1, n = 0.005–0.1) were prepared via a solid-state reaction using NH{sub 4}Cl flux. Photoluminescence spectra, the dependence of the luminescent intensity as a function of Er{sup 3+} content, and their CIE coordinates of the Er{sup 3+}-doped layered YOCl compounds were also investigated under near-ultraviolet (NUV) and visible lights. The spectral up-converting properties of Er{sup 3+} and Er{sup 3+}–Yb{sup 3+} in YOCl phosphors were elucidated under 980 and 1550 nm diode laser irradiations. This up-conversion emission spectra and the pump power dependence versus emission intensity observed in the Y{sub 0.9}Er{sub 0.1}OCl up-conversion phosphors gave rise to one- and two-photon processes. The up-conversion mechanism of Er{sup 3+} and Yb{sup 3+} ions in YOCl was described by a schematic energy-level diagram. Through the use of these up-conversion luminescent materials, the desired emitting lights throughout the orange and red regions of the spectra were achieved.

  2. NIR luminescent Er{sup 3+}/Yb{sup 3+} co-doped SiO{sub 2}-ZrO{sub 2} nanostructured planar and channel waveguides: Optical and structural properties

    Energy Technology Data Exchange (ETDEWEB)

    Cunha, Cesar dos Santos [Departamento de Quimica, Faculdade de Filosofia, Ciencias e Letras de Ribeirao Preto, Universidade de Sao Paulo, Av. Bandeirantes, 3900, 14040-901, Ribeirao Preto/SP (Brazil); Ferrari, Jefferson Luis [Grupo de Pesquisa em Quimica de Materiais - (GPQM), Departamento de Ciencias Naturais, Universidade Federal de Sao Joao Del Rei, Campus Dom Bosco, Praca Dom Helvecio, 74, 36301-160, Sao Joao Del Rei, MG (Brazil); Oliveira, Drielly Cristina de [Departamento de Quimica, Faculdade de Filosofia, Ciencias e Letras de Ribeirao Preto, Universidade de Sao Paulo, Av. Bandeirantes, 3900, 14040-901, Ribeirao Preto/SP (Brazil); Maia, Lauro June Queiroz [Grupo Fisica de Materiais, Instituto de Fisica, UFG, Campus Samambaia, Caixa Postal 131, 74001-970, Goiania/GO (Brazil); Gomes, Anderson Stevens Leonidas [Departamento de Fisica, Universidade Federal de Pernambuco, Cidade Universitaria, Recife/PE, 50670-901 (Brazil); Ribeiro, Sidney Jose Lima [Laboratorio de Materiais Fotonicos, Instituto de Quimica, UNESP, Caixa Postal 355, 14801-970, Araraquara/SP (Brazil); and others

    2012-09-14

    Optical and structural properties of planar and channel waveguides based on sol-gel Er{sup 3+} and Yb{sup 3+} co-doped SiO{sub 2}-ZrO{sub 2} are reported. Microstructured channels with high homogeneous surface profile were written onto the surface of multilayered densified films deposited on SiO{sub 2}/Si substrates by a femtosecond laser etching technique. The densification of the planar waveguides was evaluated from changes in the refractive index and thickness, with full densification being achieved at 900 Degree-Sign C after annealing from 23 up to 500 min, depending on the ZrO{sub 2} content. Crystal nucleation and growth took place together with densification, thereby producing transparent glass ceramic planar waveguides containing rare earth-doped ZrO{sub 2} nanocrystals dispersed in a silica-based glassy host. Low roughness and crack-free surface as well as high confinement coefficient were achieved for all the compositions. Enhanced NIR luminescence of the Er{sup 3+} ions was observed for the Yb{sup 3+}-codoped planar waveguides, denoting an efficient energy transfer from the Yb{sup 3+} to the Er{sup 3+} ion. Highlights: Black-Right-Pointing-Pointer Sol-gel high NIR luminescent nanostructured planar and channel waveguides. Black-Right-Pointing-Pointer Microstructured channels written by a femtosecond laser etching technique. Black-Right-Pointing-Pointer Transparent glass ceramic with rare earth-doped ZrO{sub 2} nanocrystals in a silica host. Black-Right-Pointing-Pointer Enhanced NIR luminescence, efficient energy transfer from the Yb{sup 3+} to the Er{sup 3+} ion. Black-Right-Pointing-Pointer New planar channel waveguides to be applied as EDWA in the C telecommunication band.

  3. Synthesis and up-conversion emissions of Yb3+/Er3+, Yb3+/Tm3+

    Indian Academy of Sciences (India)

    42

    which has received considerable attention for material studies [25-28]. ... Though the energy gap between the ground state 8S7/2 and the first excited state 6P7/2 of ... XRD pattern (Figure 1a) of the 20 mol% Yb3+, 2 mol% Er3+ co-doped ...

  4. Growth and spectroscopic properties of Yb{sup 3+}-doped Li{sub 6}Y(BO{sub 3}){sub 3} single crystal

    Energy Technology Data Exchange (ETDEWEB)

    Brenier, A. [Laboratoire de Physico-Chimie des Materiaux Luminescents, UMR CNRS no 5620, Universite Claude Bernard-Lyon1, 10 rue Ampere, 69622 Villeurbanne (France)]. E-mail: brenier@pcml.univ-lyon1.fr; Yoshikawa, A. [Institute of Multidisciplinary for Advanced Materials, Tohoku University, Sendai 980 8577 (Japan); Lebbou, K. [Laboratoire de Physico-Chimie des Materiaux Luminescents, UMR CNRS no 5620, Universite Claude Bernard-Lyon1, 10 rue Ampere, 69622 Villeurbanne (France); Jouini, A. [Laboratoire de Physico-Chimie des Materiaux Luminescents, UMR CNRS no 5620, Universite Claude Bernard-Lyon1, 10 rue Ampere, 69622 Villeurbanne (France); Institute of Multidisciplinary for Advanced Materials, Tohoku University, Sendai 980 8577 (Japan); Aloui-Lebbou, O. [Laboratoire de Physico-Chimie des Materiaux Luminescents, UMR CNRS no 5620, Universite Claude Bernard-Lyon1, 10 rue Ampere, 69622 Villeurbanne (France); Boulon, G. [Laboratoire de Physico-Chimie des Materiaux Luminescents, UMR CNRS no 5620, Universite Claude Bernard-Lyon1, 10 rue Ampere, 69622 Villeurbanne (France); Institute of Multidisciplinary for Advanced Materials, Tohoku University, Sendai 980 8577 (Japan); Fukuda, T. [Institute of Multidisciplinary for Advanced Materials, Tohoku University, Sendai 980 8577 (Japan)

    2007-10-15

    The spectroscopic properties of high-quality Czochralski grown 20% Yb{sup 3+}-doped Li{sub 6}Y(BO{sub 3}){sub 3} single crystal as new promising laser material are presented. The crystal was seeded-grown in the <0 1 0> direction and its crystallinity was measured using X-ray rocking curve analysis. Low temperature transmission spectrum exhibits broad bands in a short range of wavelengths and two sharp lines at 972.5 and 978 nm, interpreted as two zero-lines of two nonequivalent Yb{sup 3+} centers inside the lattice. The fluorescence lifetimes associated to these two intense lines are different: 0.867 and 1.33 ms. An attempt of determination of the Stark sublevels energies of the {sup 4}F{sub 5/2} and {sup 4}F{sub 7/2} manifolds of the two Yb{sup 3+} nonequivalent ions is given. The polarized absorption and emission spectra were also recorded at room temperature and we conclude that the most favorable emission line for laser application could be around 1042 nm in n {sub g} polarization.

  5. BaYb2F8, a new radiation hard Cherenkov radiator for electromagnetic calorimeters

    International Nuclear Information System (INIS)

    Aseev, A.A.; Devitsin, E.G.; Komar, A.A.; Kozlov, V.A.; Hovsepyan, Yu.I.; Potashov, S.Yu.; Sokolovsky, K.A.; Uvarova, T.V.; Vasilchenko, V.G.

    1992-01-01

    Radiation hardness and optical properties of a new Cherenkov radiator, heavy fluoride BaYb 2 F 8 doped with various elements, have been studied. The above mentioned crystal has the density of 7 g/cm 3 , the radiation length is 1.28 cm and the Moliere radius 2.44 cm. High radiation hardness has been demonstrated for BaYb 2 F 8 doped with Tm, Pr, Tb. (orig.)

  6. Combustion synthesis and photoluminescence properties of LaAlO{sub 3} nanophosphors doped with Yb{sup 3+} ions

    Energy Technology Data Exchange (ETDEWEB)

    Dhahri, A. [Laboratoire de Physico-chimie des Matériaux Minéraux et leurs Applications, Centre National des Recherches en Sciences des Matériaux, Technopole de Borj Cedria, B.P. 73, Soliman 8027 (Tunisia); Horchani-Naifer, K., E-mail: karima_horchani@yahoo.com [Laboratoire de Physico-chimie des Matériaux Minéraux et leurs Applications, Centre National des Recherches en Sciences des Matériaux, Technopole de Borj Cedria, B.P. 73, Soliman 8027 (Tunisia); Benedetti, A. [Dipartimento di Scienze Molecolari e Nanosistemi, Università Ca’ Foscari Venezia, Dorsoduro 2137, 30123 Venezia (Italy); Enrichi, F. [CIVEN – Coordinamento Interuniversitario Veneto per le Nanotecnologie, Via Delle Industrie 5, Marghera, Venice 30175 (Italy); Ferid, M. [Laboratoire de Physico-chimie des Matériaux Minéraux et leurs Applications, Centre National des Recherches en Sciences des Matériaux, Technopole de Borj Cedria, B.P. 73, Soliman 8027 (Tunisia)

    2014-09-15

    Ytterbium doped lanthanum aluminate (LaAlO{sub 3}) nanophosphors have been prepared by a combustion process with glycine as a fuel. The structures of the powders were determined by X-ray diffraction (XRD), the morphology of the annealed materials was observed using scanning electron microscopy (SEM), the average crystalline grain sizes have been determined by transmission electron microscopy (TEM) and photoluminescence properties using fluorescence spectroscopy. Pure LaAlO{sub 3} phase was obtained at 800 °C heated for 4 h, with an average crystal size, as determined by TEM, of 60 nm. Emission spectra and decay times of main luminescence transitions were measured at room temperature. A strong emission is reported at 986 nm from the ({sup 2}F{sub 5/2}→{sup 2}F{sub 7/2}) transition, whose intensity depends on Yb concentration. - Highlights: • Ytterbium doped lanthanum aluminate (LaAlO{sub 3}) nanophosphors have been prepared by a combustion process with glycine as a fuel. • Powders were characterized by DRX, FTIR, TEM and fluorescence spectroscopy. • Pure LaAlO{sub 3} phase was obtained at 800 °C heated for 4 h, with an average crystal size of 60 nm. • A strong emission is reported at 986 nm from the ({sup 2}F{sub 5/2}→{sup 2}F{sub 7/2}) transition, whose intensity depends on Yb concentration.

  7. Evaluation of TeO2 content on the optical and spectroscopic properties of Yb3 +-doped calcium borotellurite glasses

    Science.gov (United States)

    Lima, A. M. O.; Gomes, J. F.; Hegeto, F. L.; Medina, A. N.; Steimacher, A.; Barboza, M. J.

    2018-03-01

    This paper reports the synthesis and the characterization of Yb3 +-doped calcium borotellurite (CaBTeX) glasses with composition 10CaF2-(29.5 - 0.4x)CaO-(60 - 0.6x)B2O3-xTeO2-0.5Yb2O3 (x = 10, 16, 22, 31 and 54 mol%). The results of XRD confirm the amorphous character of all the samples. The density, molar volume, refractive index and electronic polarizability values show an increase with TeO2 content. Otherwise, the optical band gap energy shows a decrease with the increase of TeO2 content. The replacement of CaO and B2O3 by TeO2 changes the glass structure, which decreases the excited Yb3 +/cm3 and, consequently, the luminescence intensity. The temperature dependence of luminescence was studied for all the samples up to 420 K. The fluorescence lifetime does not change significantly due to TeO2 addition. In addition, absorption and emission cross section were calculated and present high values as compared to other tellurite and phosphate glasses.

  8. The upconversion luminescence and magnetism in Yb3+/Ho3+ co-doped LaF3 nanocrystals for potential bimodal imaging

    Science.gov (United States)

    Syamchand, Sasidharanpillai S.; George, Sony

    2016-12-01

    Biocompatible upconversion nanoparticles with multifunctional properties can serve as potential nanoprobes for multimodal imaging. Herein, we report an upconversion nanocrystal based on lanthanum fluoride which is developed to address the imaging modalities, upconversion luminescence imaging and magnetic resonance imaging (MRI). Lanthanide ions (Yb3+ and Ho3+) doped LaF3 nanocrystals (LaF3 Yb3+/Ho3+) are fabricated through a rapid microwave-assisted synthesis. The hexagonal phase LaF3 nanocrystals exhibit nearly spherical morphology with average diameter of 9.8 nm. The inductively coupled plasma mass spectrometry (ICP-MS) analysis estimated the doping concentration of Yb3+ and Ho3+ as 3.99 and 0.41%, respectively. The nanocrystals show upconversion luminescence when irradiated with near-infrared (NIR) photons of wavelength 980 nm. The emission spectrum consists of bands centred at 542, 645 and 658 nm. The stronger green emission at 542 nm and the weak red emissions at 645 and 658 nm are assigned to 5S2 → 5I8 and 5F5 → 5I8 transitions of Ho3+, respectively. The pump power dependence of luminescence intensity confirmed the two-photon upconversion process. The nanocrystals exhibit paramagnetism due to the presence of lanthanide ion dopant Ho3+ and the magnetization is 19.81 emu/g at room temperature. The nanocrystals exhibit a longitudinal relaxivity ( r 1) of 0.12 s-1 mM-1 and transverse relaxivity ( r 2) of 28.18 s-1 mM-1, which makes the system suitable for developing T2 MRI contrast agents based on holmium. The LaF3 Yb3+/Ho3+ nanocrystals are surface modified by PEGylation to improve biocompatibility and enhance further functionalisation. The PEGylated nanocrystals are found to be non-toxic up to 50 μg/mL for 48 h of incubation, which is confirmed by the MTT assay as well as morphological studies in HeLa cells. The upconversion luminescence and magnetism together with biocompatibility enables the adaptability of the present system as a nanoprobe for potential

  9. Enhanced exciton emission from ZnO nano-phosphor induced by Yb3+ ions

    CSIR Research Space (South Africa)

    Kabongo, GL

    2014-01-01

    Full Text Available In this work, the sol–gel method was used to prepare Ytterbium (Yb(sup3+)) doped ZnO nano-phosphors with different concentrations of Yb(sup3+) ions. Their structural, morphological, photoluminescence, electronic states and the chemical composition...

  10. Ridge optical waveguide in an Er3+/Yb3+ co-doped phosphate glass produced by He+ ion implantation combined with Ar+ ion beam etching

    International Nuclear Information System (INIS)

    Tan Yang; Chen Feng; Hu Lili; Xing Pengfei; Chen Yanxue; Wang Xuelin; Wang Keming

    2007-01-01

    This paper reports on the fabrication and characterization of a ridge optical waveguide in an Er 3+ /Yb 3+ co-doped phosphate glass. The He + ion implantation (at energy of 2.8 MeV) is first applied onto the sample to produce a planar waveguide substrate, and then Ar + ion beam etching (at energy of 500 eV) is carried out to construct rib stripes on the sample surface that has been deposited by a specially designed photoresist mask. According to a reconstructed refractive index profile of the waveguide cross section, the modal distribution of the waveguide is simulated by applying a computer code based on the beam propagation method, which shows reasonable agreement with the experimentally observed waveguide mode by using the end-face coupling method. Simulation of the incident He ions at 2.8 MeV penetrating into the Er 3+ /Yb 3+ co-doped phosphate glass substrate is also performed to provide helpful information on waveguide formation

  11. ZnMoO4:Er3+,Yb3+ phosphor with controlled morphology and enhanced upconversion through alkali ions doping

    Science.gov (United States)

    Luitel, Hom Nath; Chand, Rumi; Watari, Takanori

    2018-04-01

    A facile hydrothermal method was used to synthesize ZnMoO4:Er3+,Yb3+ nanoparticles. The shapes and sizes of the nanoparticles were well tuned by simply monitoring the pH of the starting solution. Microballs consisting of agglomerated nanograins were observed at strong acidic condition. At mild pH, plates and rectangular particles were realized, while strong basic pH stabilized rods. Further increasing pH to extremely basic conditions (pH > 13), rods changed to fragile hairy structures. The nucleation and growth mechanism of nanograins to form different morphology nanoparticles were studied and illustrated. XRD patterns confirmed well crystalline, triclinic structure despite small amount of aliovalent metal ions doping. Under 980 nm excitation, the ZnMoO4:Er3+,Yb3+ nanophosphor exhibited strong green (centered at 530 and 560 nm) and weak red (centered at 660 nm) upconversion (UC) emissions. Substitution of part of the Zn2+ ions by monovalent alkali ions intensified the UC emission intensities drastically. The order of intensification was K+>Na+>Li+>Rb+>no alkali ion. When Zn2+ ions were substituted with 10 at% K+ ions, the green and red UC emissions intensities increased by more than 50 and 15 folds, respectively. Time dependent measurements confirmed efficient Yb to Er energy transfer in the ZnMoO4:Er3+,Yb3+,K+ nanophosphor. The optimized ZnMoO4:Er3+,Yb3+,K+ phosphor exhibited intense UC emissions with 0.31% quantum yield. The upconverted light is visible to naked eye while pumping by laser of less than 1 mW power and opens door for variety of novel applications.

  12. Hydrogen Passivation of N(+)P and P(+)N Heteroepitaxial InP Solar Cell Structures

    Science.gov (United States)

    Chatterjee, B.; Davis, W. C.; Ringel, S. A.; Hoffman, R., Jr.

    1995-01-01

    Dislocations and related point defect complexes caused by lattice mismatch currently limit the performance of heteroepitaxial InP cells by introducing shunting paths across the active junction and by the formation of deep traps within the base region. We have previously demonstrated that plasma hydrogenation is an effective and stable means to passivate the electrical activity of such defects in specially designed heteroepitaxial InP test structures to probe hydrogen passivation at typical base depths within a cell structure. In this work, we present our results on the hydrogen passivation of actual heteroepitaxial n(+)p and p(+)n InP cell structures grown on GaAs substrates by metalorganic chemical vapor deposition (MOCVD). We have found that a 2 hour exposure to a 13.56 MHz hydrogen plasma at 275 C reduces the deep level concentration in the base regions of both n(+)p and p(+)n heteroepitaxial InP cell structures from as-grown values of 5 - 7 x 10(exp 14)/cc, down to 3 - 5 x 10(exp 12)/cc. All dopants were successfully reactivated by a 400 C, 5 minute anneal With no detectable activation of deep levels. I-V analysis indicated a subsequent approx. 100 fold decrease In reverse leakage current at -1 volt reverse bias, and an improved built in voltage for the p(+)n structures. ln addition to being passivated,dislocations are also shown to participate in secondary interactions during hydrogenation. We find that the presence of dislocations enhances hydrogen diffusion into the cell structure, and lowers the apparent dissociation energy of Zn-H complexes from 1.19 eV for homoepitaxial Zn-doped InP to 1.12 eV for heteroepitaxial Zn-doped InP. This is explained by additional hydrogen trapping at dislocations subsequent to the reactivation of Zn dopants after hydrogenation.

  13. Hydrogen passivation of N(+)-P and P(+)-N heteroepitaxial InP solar cell structures

    Science.gov (United States)

    Chatterjee, Basab; Davis, William C.; Ringel, Steve A.; Hoffman, Richard, Jr.

    1996-01-01

    Dislocations and related point defect complexes caused by lattice mismatch currently limit the performance of heteroepitaxial InP cells by introducing shunting paths across the active junction and by the formation of deep traps within the base region. We have previously demonstrated that plasma hydrogenation is an effective and stable means to passivate the electrical activity of such defects in specially designed heteroepitaxial InP test structures to probe hydrogen passivation at typical base depths within a cell structure. In this work, we present our results on the hydrogen passivation of actual heteroepitaxial n-p and p-n InP cell structures grown on GaAs substrates by metalorganic chemical vapor deposition (MOCVD). We have found that a 2 hour exposure to a 13.56 MHz hydrogen plasma at 275 C reduces the deep level concentration in the base regions of both n(+)-p and p(+)-n heteroepitaxial InP cell structures from as-grown values of 5-7 x 10(exp 14) cm(exp -3), down to 3-5 x 10(exp 12) cm(exp -3). All dopants were successfully reactivated by a 400 C, 5 minute anneal with no detectable activation of deep levels. One to five analysis indicated a subsequent approximately 100 fold decrease in reverse leakage current at -1 volt reverse bias, and an improved built in voltage for the p(+)-n structures. In addition to being passivated, dislocations are also shown to participate in secondary interactions during hydrogenation. We find that the presence of dislocations enhances hydrogen diffusion into the cell structure, and lowers the apparent dissociation energy of Zn-H complexes from 1.19 eV for homoepitaxial Zn-doped InP to 1.12 eV for heteroepitaxial Zn-doped InP. This is explained by additional hydrogen trapping at dislocations subsequent to the reactivation of Zn dopants after hydrogenation.

  14. Spatially selective Er/Yb-doped CaF{sub 2} crystal formation by CO{sub 2} laser exposure

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Dong-Seon; Lee, Jin-Ho; Lim, Ki-Soo, E-mail: kslim@chungbuk.ac.kr

    2014-10-30

    Highlights: • Oxyfluoride glass–ceramics containing CaF{sub 2} nanocrystals doped with Er{sup 3+} and Yb{sup 3+} ions were formed on the glass surface by CO{sub 2} laser and a heat gun exposure. • Most of Er and Yb ions were distributed inside CaF{sub 2} nanocrystals and fluorine loss was observed in the EDS element maps. • IR-to-VIS upconversion emission efficiency of laser annealed glass ceramics was much increased and compared with that of the furnace-annealed glass ceramics. • Distributed volume of the glass ceramics were estimated by a confocal fluorescence microscope imaging. - Abstract: We report the glass–ceramic precipitation on the oxyfluoride glass surface by spatially selective annealing with a CO{sub 2} laser and a heat gun exposure. X-ray diffraction analysis showed the formation of major CaF{sub 2} and miner Ca{sub 2}SiO{sub 4} nanoparticles. We observed ∼100 nm nanoparticle aggregation by tunneling electron microscopy and element distribution in glass and crystal phases. Spatial distribution of glass ceramics near the glass surface was probed by confocal fluorescence microscope by using much enhanced emission from the Er ions in the laser-treated area. Strong emissions at 365 nm excitation and visible up-conversion emissions at 980 nm excitation also indicated well incorporation of Er and Yb ions into a crystalline environment.

  15. Spatially selective Er/Yb-doped CaF{sub 2} crystal formation by CO{sub 2} laser exposure

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Dong-Seon; Lee, Jin-Ho; Lim, Ki-Soo, E-mail: kslim@chungbuk.ac.kr

    2015-04-15

    Highlights: • Oxyfluoride glass–ceramics containing CaF{sub 2} nanocrystals doped with Er{sup 3+} and Yb{sup 3+} ions were formed on the glass surface by CO{sub 2} laser and a heat gun exposure. • Most of Er and Yb ions were distributed inside CaF{sub 2} nanocrystals and fluorine loss was observed in the EDS element maps. • IR-to-VIS upconversion emission efficiency of laser annealed glass ceramics was much increased and compared with that of the furnace-annealed glass ceramics. • Distributed volume of the glass ceramics were estimated by a confocal fluorescence microscope imaging. - Abstract: We report the glass–ceramic precipitation on the oxyfluoride glass surface by spatially selective annealing with a CO{sub 2} laser and a heat gun exposure. X-ray diffraction analysis showed the formation of major CaF{sub 2} and miner Ca{sub 2}SiO{sub 4} nanoparticles. We observed ∼100 nm nanoparticle aggregation by tunneling electron microscopy and element distribution in glass and crystal phases. Spatial distribution of glass ceramics near the glass surface was probed by confocal fluorescence microscope by using much enhanced emission from the Er ions in the laser-treated area. Strong emissions at 365 nm excitation and visible up-conversion emissions at 980 nm excitation also indicated well incorporation of Er and Yb ions into a crystalline environment.

  16. Upconversion emission and cathodoluminescence of Er"3"+-doped NaYbF_4 nanoparticles for low-temperature thermometry and field emission displays

    International Nuclear Information System (INIS)

    Du, Peng; Yu, Jae Su; Luo, Laihui

    2017-01-01

    The Er"3"+-doped NaYbF_4 nanoparticles were fabricated by a hydrothermal method. The green and red emissions located at around 525, 542 and 657 nm corresponding to the "2H_1_1_/_2 → "4I_1_5_/_2, "4S_3_/_2 → "4I_1_5_/_2 and "4F_9_/_2 → "4I_1_5_/_2 transitions of Er"3"+ ions, respectively, were observed when pumped at 980 nm light. Furthermore, with the help of the fluorescence intensity ratio technique, the thermometric properties of as-prepared products from the thermally coupled "2H_1_1_/_2 and "4S_3_/_2 levels of Er"3"+ ions were studied by analyzing temperature-dependent upconversion (UC) emission spectra. The maximum sensitivity for the Er"3"+-doped NaYbF_4 nanoparticles was found to be around 0.0043 K"- "1 with a temperature range of 93-293 K. In addition, the cathodoluminescence (CL) spectrum of the synthesized nanoparticles was nearly the same as the UC emission spectrum and the CL emission intensity did not exhibit saturation with the increase of accelerating voltage and filament current. (orig.)

  17. Microstructural and electrical characteristics of rare earth oxides doped ZnO varistor films

    Science.gov (United States)

    Jiao, Lei; Mei, Yunzhu; Xu, Dong; Zhong, Sujuan; Ma, Jia; Zhang, Lei; Bao, Li

    2018-02-01

    ZnO-Bi2O3 varistor films doped with two kinds of rare earth element oxides (Lu2O3 and Yb2O3) were prepared by the sol-gel method. The effects of Lu2O3/Yb2O3 doping on the microstructure and electrical characteristics of ZnO-Bi2O3 varistor films were investigated. All samples show a homogenized morphology and an improved nonlinear relationship between the electric field (E) and current density (I). Both Yb2O3 and Lu2O3 doping can decrease the grain size of ZnO-Bi2O3 varistor films and improve the electrical properties, which have a positive effect on the development of ZnO varistor ceramics. Yb2O3 doping significantly increases the dielectric constant at low frequency. 0.2 mol. % Yb2O3 doped ZnO-Bi2O3 varistor films exhibit the highest nonlinear coefficient (2.5) and the lowest leakage current (328 μA) among Lu2O3/Yb2O3 doped ZnO-Bi2O3 varistor films. Similarly, 0.1 mol. % Lu2O3 doping increases the nonlinear coefficient to 1.9 and decrease the leakage current to 462 μA.

  18. A comprehensive phononics of phonon assisted energy transfer in the Yb3+ aided upconversion luminescence of Tm3+ and Ho3+ in solids

    International Nuclear Information System (INIS)

    Debnath, Radhaballabh; Bose, Saptasree

    2015-01-01

    The theory of phonon assisted energy transfer is being widely used to explain the Yb 3+ ion aided normal and upconversion emission of various rare earth ions in different Yb 3+ co-doped solids. The reported phonon dynamics in many of these studies are either incomplete or erroneous. Here we report Yb 3+ aided upconversion luminescence properties of Tm 3+ and Ho 3+ in (Yb 3+ /Tm 3+ ) and (Yb 3+ /Ho 3+ ) co-doped two BaO–tellurite glasses and explain their phononics in the light of Dexter's theory by proposing a comprehensive scheme. The approach is valid for other systems of different phonon structures. - Highlights: • Yb 3+ aided upconversion luminescence properties of Tm 3+ and Ho 3+ in (Yb 3+ /Tm 3+ ) and (Yb 3+ /Ho 3+ ) co-doped two BaO–tellurite glasses, are reported. • Phonon assisted energy transfer in these systems are explained in the light of Dexter's theory by proposing a comprehensive scheme of phononics. • The approach is valid for other systems of different phonon structures

  19. Electron spin resonance in Yb-based Kondo-lattice systems

    International Nuclear Information System (INIS)

    Wykhoff, Jan

    2010-01-01

    The systems Yb 1-w A 1-w (Rh 1-x Co x )(Si 1-y Ge y ) 2 with A=La respectively Lu, as well as YbIr 2 Si 2 are studied. The measurements are presented sortedly for systems, dopings, and external parameters. Beside these external parameters furthermore the orientation of the sample related to the quasistatic magnetic field and the microwave magnetic field was varied.

  20. Enhancing upconversion emission of Er, Yb co-doped highly transparent YF3 films by synergistic tuning nano-textured morphology and crystallinity

    International Nuclear Information System (INIS)

    Qu, Ming-Hao; Wang, Ru-Zhi; Chen, Yan; Zhang, Ying; Li, Kai-Yu; Zhou, Hua; Yan, Hui

    2014-01-01

    Highly transparent Er, Yb codoped YF 3 upconversion films were successfully prepared by electron beam deposition method. The effects of the substrate temperature on the morphology, crystallinity and emission characteristics of Er, Yb codoped YF 3 films were studied carefully. It was found that the morphology and crystallinity varied from smooth amorphous to root-intertwined polycrystalline structure with the substrate temperature increase. Besides, the emission characteristics of the films can be modulated by the synergy of their surface morphologies and crystallinities. Remarkably, a large enhancement of the upconversion emission, up to five decades while only an insignificant decrease of the optical transmittance (10% at most), was achieved by forming root-intertwined polycrystalline structures. These highly transparent upconversion films may have good potential for enhancing the conversion efficiency of wide band-gap solar cells. -- Highlights: • Er, Yb co-dopedYF 3 upconversion films have been successfully prepared. • The upconversion property can be modulated by morphology and crystallinity. • The upconversion transparent YF 3 films are promising for solar cells applications

  1. Bright white upconversion luminescence from Er3+/Tm3+/Yb3+-doped titanate-based glasses prepared by aerodynamic levitation method

    Science.gov (United States)

    Zhang, Minghui; Yu, Jianding; Jiang, Wan; Liu, Yan; Ai, Fei; Wen, Haiqin; Jiang, Meng; Yu, Huimei; Pan, Xiuhong; Tang, Meibo; Gai, Lijun

    2017-10-01

    Aerodynamic levitation method was employed to prepare Er3+/Tm3+/Yb3+-doped titanate-based glasses. DTA results show that the glass performs high thermal stability with the glass transition temperature of 799 °C. The interaction among rare earth ions has been discussed by adjusting the relative concentration. Er3+ ions can quench the upconversion luminescence of Tm3+ ions. Tm3+ ions play a strong role in quenching the emissions of Er3+ and Tm3+ when the content of Tm3+ ions is greater than or equal 0.05. From the view of the ratio of red emission to green emission, Tm3+ ions can improve the red emission of Er3+ ions to some extent in contrast with the green emissions of Er3+ ions. 980 nm incident laser can be efficiently absorbed by Yb3+ ions. The relative intensity of red, green, and blue upconversion luminescence has been tuned to obtain white light. The composition with white upconversion luminescence of the color coordinate (0.291, 0.3292) has been found. Moreover, white upconversion luminescence mechanism is a two-photon process of ET, ESA, and cooperative sensitization. Rare earth ions doped titanate-based glasses with bright upconversion luminescence perform potential applications in color display, back light, et al.

  2. Growth and continuous-wave laser operation of disordered crystals of Yb3+:NaLa(WO4)2 and Yb3+:NaLa(MoO4)2

    International Nuclear Information System (INIS)

    Liu, J.; Rico, M.; Griebner, U.; Petrov, V.; Cano-Torres, J.M.; Cascales, C.; Esteban-Betegon, F.; Serrano, M.D.; Volkov, V.; Zaldo, C.

    2005-01-01

    Single crystals of disordered NaLa(WO 4 ) 2 and NaLa(MoO 4 ) 2 doped with Yb 3+ are grown by the Czochralski method from the melt. Continuous-wave laser operation with Ti:sapphire laser pumping is demonstrated at room temperature without special cooling. Tunability from 1017 to 1057 nm and from 1015 to 1053 nm is achieved for Yb:NaLa(WO 4 ) 2 and Yb:NaLa(MoO 4 ) 2 , respectively. A maximum output power of 205 mW is obtained with Yb:NaLa(WO 4 ) 2 . (copyright 2005 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

  3. Luminescence property and emission enhancement of YbAlO3:Mn4+ red phosphor by Mg2+ or Li+ ions

    Science.gov (United States)

    Cao, Renping; Luo, Wenjie; Xu, Haidong; Luo, Zhiyang; Hu, Qianglin; Fu, Ting; Peng, Dedong

    2016-03-01

    YbAlO3:Mn4+, YbAlO3:Mn4+, Li+, and YbAlO3:Mn4+, Mg2+ phosphors are synthesized by high temperature solid-state reaction method in air. Their crystal structures and luminescence properties are investigated. Photoluminescence excitation (PLE) spectrum monitored at 677 nm contains broad PLE band with three PLE peaks located at ∼318, 395, and 470 nm within the range 220-600 nm. Emission spectra with excitation 318 and 470 nm exhibit three emission band peaks located at ∼645, 677, and 700 nm in the range of 610-800 nm and their corresponding chromaticity coordinates are about (x = 0.6942, y = 0.3057). The possible luminous mechanism of Mn4+ ion is analyzed by the simple energy level diagram of Mn4+ ion. The optimum Mn4+-doped concentration in YbAlO3:Mn4+ phosphor is about 0.4 mol% and the luminescence lifetime of YbAlO3:0.4%Mn4+ phosphor is ∼0.59 ms. Emission intensity of YbAlO3:0.4%Mn4+ phosphor can be enhanced ∼6 times after Mg2+ ion is co-doped and it is ∼2 times when Li+ ion is co-doped. The content in the paper is useful to research new Mn4+-doped luminescence materials and improve luminescence property of other Mn4+-doped phosphors.

  4. Structural, thermal, and optical properties of Er3+/Yb3+ co-doped oxyhalide tellurite glasses, glass-ceramics and ceramics

    International Nuclear Information System (INIS)

    Joshi, C.; Rai, R.N.; Rai, S.B.

    2012-01-01

    Glass-ceramics and ceramics containing nano-crystals of different phases doped with Er 3+ /Yb 3+ ions have been successfully prepared by heat treatment of the precursor oxyhalide glasses synthesized by the melt-quench method. X-ray diffraction patterns and transmission electron microscopy (TEM) images verify the precipitation of nano-crystals. Emission of Er 3+ enhances several times when Yb 3+ ion is added with the matrix. The Stark splitting and the intensity of different emission bands increase to a great extent when we approach to ceramics from glasses via glass-ceramics. The intensity of the blue and green emission bands increases much faster than the red and NIR emission bands. Intense upconversion emission observed by the naked eye has been quantified in terms of standard chromaticity diagram (CIE). Power dependence study shows that the upconversion of NIR radiation to visible radiation takes place mainly via photon avalanche (PA) process.

  5. Cathodoluminescence study of ytterbium doped GaSb

    International Nuclear Information System (INIS)

    Hidalgo, P.; Mendez, B.; Ruiz, C.; Bermudez, V.; Piqueras, J.; Dieguez, E.

    2005-01-01

    Yb-doped GaSb ingots have been grown by the Bridgman method. The defect structure and compositional homogeneity of the crystals have been investigated by cathodoluminescence and X-ray microanalysis in the scanning electron microscope. The nature of the point defects has been found to depend on the position along the growth axis. Doping with Yb has been found to reduce the luminescence intensity of GaSb and no infrared emission related to intra-ionic transitions of the Yb 3+ ions has been detected

  6. Strong broad green UV-excited photoluminescence in rare earth (RE = Ce, Eu, Dy, Er, Yb) doped barium zirconate

    Energy Technology Data Exchange (ETDEWEB)

    Borja-Urby, R. [Grupo de Espectroscopia de Materiales Avanzados y Nanoestructurados (EMANA), Centro de Investigaciones en Optica A. C., Leon, Gto. 37150 (Mexico); Diaz-Torres, L.A., E-mail: ditlacio@cio.mx [Grupo de Espectroscopia de Materiales Avanzados y Nanoestructurados (EMANA), Centro de Investigaciones en Optica A. C., Leon, Gto. 37150 (Mexico); Salas, P. [Centro de Fisica Aplicada y Tecnologia Avanzada, Universidad Nacional Autonoma de Mexico, A.P. 1-1010, Queretaro, Qro. 76000 (Mexico); Angeles-Chavez, C. [Instituto Mexicano del Petroleo, Ciudad de Mexico, D. F. 07730 (Mexico); Meza, O. [Grupo de Espectroscopia de Materiales Avanzados y Nanoestructurados (EMANA), Centro de Investigaciones en Optica A. C., Leon, Gto. 37150 (Mexico)

    2011-10-25

    Highlights: > Trivalent rare earth (RE) substitution on Zr{sup 4+} sites in BaZrO{sub 3} lead to band gap narrowing. > RE substitution lead to enhanced blue-green intrinsic emission of nanocrystalline BaZrO{sub 3} > Blue-green hue of BaZrO3:RE depends on RE dopant and excitation UV wavelength > BaZrO3: Dy{sup 3+} PL chromatic coordinates correspond to pure white color coordinates of CIE 1931 model - Abstract: The wet synthesis hydrothermal method at 100 deg. C was used to elaborate barium zirconate (BaZrO{sub 3}) unpurified with 0.5 mol% of different rare earth ions (RE = Yb, Er, Dy, Eu, Ce). Morphological, structural and UV-photoluminescence properties depend on the substituted rare earth ionic radii. While the crystalline structure of RE doped BaZrO{sub 3} remains as a cubic perovskite for all substituted RE ions, its band gap changes between 4.65 and 4.93 eV. Under 267 nm excitation the intrinsic green photoluminescence of the as synthesized BaZrO{sub 3}: RE samples is considerably improved by the substitution on RE ions. For 1000 deg. C annealed samples, under 267 nm, the photoluminescence is dominated by the intrinsic BZO emission. It is interesting to notice that Dy{sup 3+}, Er{sup 3+} and Yb{sup 3+} doped samples present whitish emissions that might be useful for white light generation under 267 nm excitation. CIE color coordinates are reported for all samples.

  7. Synthesis and photocatalytic activity of ytterbium-doped titania/diatomite composite photocatalysts

    International Nuclear Information System (INIS)

    Tang, Wenjian; Qiu, Kehui; Zhang, Peicong; Yuan, Xiqiang

    2016-01-01

    Graphical abstract: - Highlights: • Yb-doped TiO_2/diatomite composite photocatalysts were prepared by a sol-gel method. • Yb-doped TiO_2/diatomite photocatalysts show much higher photocatalytic activity. • The higher photodegradation rate is due to the effect of diatomite and Yb doping. - Abstract: Ytterbium-doped titanium dioxide (Yb-TiO_2)/diatomite composite materials with different Yb concentrations were prepared by sol–gel method. The phase structure, morphology, and chemical composition of the as-prepared composites were well characterized by X-ray diffraction (XRD), Fourier transform infrared spectroscopy, Raman spectroscopy, scanning electron microscopy (SEM), and ultraviolet–visible (UV–vis) diffuse reflection spectroscopy. The XRD and Raman spectroscopy analysis indicated that the TiO_2 existed in the form of pure anatase in the composites. The SEM images exhibited the well deposition and dispersion of TiO_2 nanoparticles with little agglomeration on the surfaces of diatoms. The UV–vis diffuse reflection spectra showed that the band gap of TiO_2 could be narrowed by the introduction of Yb species, which was further affected by doping concentration of Yb. The photocatalytic activity of synthesized samples was investigated by the degradation of methylene blue (MB) under UV light irradiation. It was observed that the photocatalytic degradation followed a pseudo-first-order kinetics according to the Langmuir–Hinshelwood model. Compared to TiO_2 and TiO_2/diatomite, the Yb-TiO_2/diatomite composites exhibited higher photocatalytic activity toward degradation of MB using UV light irradiation.

  8. Synthesis and photocatalytic activity of ytterbium-doped titania/diatomite composite photocatalysts

    Energy Technology Data Exchange (ETDEWEB)

    Tang, Wenjian; Qiu, Kehui; Zhang, Peicong; Yuan, Xiqiang

    2016-01-30

    Graphical abstract: - Highlights: • Yb-doped TiO{sub 2}/diatomite composite photocatalysts were prepared by a sol-gel method. • Yb-doped TiO{sub 2}/diatomite photocatalysts show much higher photocatalytic activity. • The higher photodegradation rate is due to the effect of diatomite and Yb doping. - Abstract: Ytterbium-doped titanium dioxide (Yb-TiO{sub 2})/diatomite composite materials with different Yb concentrations were prepared by sol–gel method. The phase structure, morphology, and chemical composition of the as-prepared composites were well characterized by X-ray diffraction (XRD), Fourier transform infrared spectroscopy, Raman spectroscopy, scanning electron microscopy (SEM), and ultraviolet–visible (UV–vis) diffuse reflection spectroscopy. The XRD and Raman spectroscopy analysis indicated that the TiO{sub 2} existed in the form of pure anatase in the composites. The SEM images exhibited the well deposition and dispersion of TiO{sub 2} nanoparticles with little agglomeration on the surfaces of diatoms. The UV–vis diffuse reflection spectra showed that the band gap of TiO{sub 2} could be narrowed by the introduction of Yb species, which was further affected by doping concentration of Yb. The photocatalytic activity of synthesized samples was investigated by the degradation of methylene blue (MB) under UV light irradiation. It was observed that the photocatalytic degradation followed a pseudo-first-order kinetics according to the Langmuir–Hinshelwood model. Compared to TiO{sub 2} and TiO{sub 2}/diatomite, the Yb-TiO{sub 2}/diatomite composites exhibited higher photocatalytic activity toward degradation of MB using UV light irradiation.

  9. Yb:Lu{sub 2}O{sub 3} hydrothermally-grown single-crystal and ceramic absorption spectra obtained between 298 and 80 K

    Energy Technology Data Exchange (ETDEWEB)

    Moore, Cheryl A. [Snake Creek Lasers LLC, 26741 State Route 267, Friendsville, PA 18818 (United States); Department of Chemistry and Center for Optical Materials Science and Engineering Technologies, Clemson University, Clemson, SC 29634-0973 (United States); Brown, David C., E-mail: dbrown@snakecreeklasers.com [Snake Creek Lasers LLC, 26741 State Route 267, Friendsville, PA 18818 (United States); Sanjeewa, Liurukara D.; McMillen, Colin D.; Kolis, Joseph W. [Department of Chemistry and Center for Optical Materials Science and Engineering Technologies, Clemson University, Clemson, SC 29634-0973 (United States)

    2016-06-15

    The hydrothermal growth, doping, and low temperature spectral characterization of Yb doped Lu{sub 2}O{sub 3} was investigated. The absorption of the lutetia-based sesquioxide laser material Yb:Lu{sub 2}O{sub 3} at temperatures of 80, 150, 200, 250, and 298 K, in the wavelength range of 850–1100 nm are reported. Data for both single crystal and ceramic Yb:Lu{sub 2}O{sub 3} were obtained. The resulting absorption cross-section data will enable the further evaluation of Yb:Lu{sub 2}O{sub 3} as a very promising high power cryogenic laser material.

  10. Lifetime measurements by open circuit voltage decay in GaAs and InP diodes

    International Nuclear Information System (INIS)

    Bhimnathwala, H.G.; Tyagi, S.D.; Bothra, S.; Ghandhi, S.K.; Borrego, J.M.

    1990-01-01

    Minority carrier lifetimes in the base of solar cells made in GaAs and InP are measured by open circuit voltage decay method. This paper describes the measurement technique and the conditions under which the minority carrier lifetimes can be measured. Minority carrier lifetimes ranging from 1.6 to 34 ns in InP of different doping concentrations are measured. A minority carrier lifetime of 6 ns was measured in n-type GaAs which agrees well with the lifetime of 5.7 ns measured by transient microwave reflection

  11. High-beam quality, high-efficiency laser based on fiber with heavily Yb(3+)-doped phosphate core and silica cladding.

    Science.gov (United States)

    Egorova, O N; Semjonov, S L; Medvedkov, O I; Astapovich, M S; Okhrimchuk, A G; Galagan, B I; Denker, B I; Sverchkov, S E; Dianov, E M

    2015-08-15

    We have fabricated and tested a composite fiber with an Yb(3+)-doped phosphate glass core and silica cladding. Oscillation with a slope efficiency of 74% was achieved using core pumping at 976 nm with fiber lengths of 48-90 mm in a simple laser configuration, where the cavity was formed by a high-reflectivity Bragg grating and the cleaved fiber end. The measured M(2) factors were as low as 1.05-1.22 even though the fiber was multimode at the lasing wavelength.

  12. The lower yield point of InP and GaAs

    International Nuclear Information System (INIS)

    Siethoff, H.

    1987-01-01

    A study of the strain-rate and temperature dependence of the lower yield stress (τ ly ) in undoped InP and of the strain-rate dependence of τ ly in undoped and Zn-doped GaAs is reported. The deformation along (123) orientation was carried out in compression at constant strain rates ranging from 10 -5 to 10 -2 s -1 . The temperature range extended from 540 to 780 0 C. The activation energy and stress exponent of the dislocation velocity were calculated. Experiments have shown that τ ly of InP depends on temperature and strain rate in a manner similar to other semiconductors like Si and InSb, whereas τ ly of GaAs shows an unusual strain-rate dependence

  13. Photon up-conversion production in Tb{sup 3+}–Yb{sup 3+} co-doped CaF{sub 2} phosphors prepared by combustion synthesis

    Energy Technology Data Exchange (ETDEWEB)

    Rakov, Nikifor, E-mail: nikifor.gomez@univasf.edu.br [PG—Ciência dos Materiais, Universidade Federal do Vale do São Francisco, 48902-300 Juazeiro, BA (Brazil); Guimarães, Renato B. [Instituto de Física, Universidade Federal Fluminense, 24210-346 Niterói, RJ (Brazil); Maciel, Glauco S., E-mail: glauco@if.uff.br [Instituto de Física, Universidade Federal Fluminense, 24210-346 Niterói, RJ (Brazil)

    2016-02-15

    Graphical abstract: Up-conversion luminescence from Tb{sup 3+} obtained by energy transfer from Yb{sup 3+} pairs in CaF{sub 2} powder prepared by combustion synthesis. - Highlights: • Calcium fluoride (CaF{sub 2}) powders were prepared by combustion synthesis. • Rare-earth ions doped in this material were found in interstitial sites. • Cooperative up-conversion was observed in Tb{sup 3+}:Yb{sup 3+}:CaF{sub 2} powder. • Energy transfer between Tb{sup 3+} and pairs of Yb{sup 3+} was analyzed using rate equations. - Abstract: Calcium fluoride (CaF{sub 2}) crystalline powders were successfully prepared by the combustion synthesis method. The powder material containing luminescent rare-earth ions, more specifically terbium (Tb{sup 3+}) and ytterbium (Yb{sup 3+}), was studied by X-ray diffraction, scanning electronic microscopy and optical spectroscopy. These ions are allocated in charge compensated interstitial positions of tetragonal (C{sub 4v}) and trigonal (C{sub 3v}) symmetry sites of the cubic (O{sub h}) CaF{sub 2} lattice. Up-conversion (UC) luminescence in Tb{sup 3+} was achieved using a low power diode laser operating at 975 nm. Tb{sup 3+} is insensitive to near-infrared radiation but UC can be achieved via energy transfer from pairs of Yb{sup 3+} ions to Tb{sup 3+} ions. The UC luminescence dynamics of Tb{sup 3+} was used to study the energy transfer mechanism.

  14. Synthesis–property relationship in thermoelectric Sr 1− x Yb x TiO 3− δ ceramics

    KAUST Repository

    Bhattacharya, S

    2014-08-22

    The electronic transport properties of a series of Sr1-xYbxTiO3-delta (x = 0.05, 0.1) ceramics are investigated as a function of solid-state reaction (SSR) parameters, specifically calcination steps. It was found that the electrical conductivity (sigma) increases almost by a factor of 6, through the optimization of SSR parameters. The enhancement in the electrical conductivity leads to an enhancement in the thermoelectric power factor by a factor of 3. In addition, the lattice thermal conductivity (k(L)) of the Sr1-xYbxTiO3-delta ceramics is suppressed with increasing Yb-doping, supposedly due to heavier atomic mass of Yb substituted at the Sr site and a smaller ionic radii of Yb+3 with respect to Sr+2 ions. However, our model calculations indicate that strain-field effect, which occurs due to the difference in ionic radii, is the more prominent phonon scattering mechanism in the Yb-doped SrTiO3. This work is an extension of our previous study on the underlying phonon scattering mechanisms in the Y-doped SrTiO3, which would provide new insight into thermal transport in doped SrTiO3 and could be used as a guideline for more effective material synthesis.

  15. Photoreflection investigations of the dopant activation in InP doped with beryllium ions

    International Nuclear Information System (INIS)

    Avakyants, L.P.; Bokov, P.Yu.; Chervyakov, A.V.

    2005-01-01

    The processes of the dopant activation in the InP crystals implanted with Be + ions (energy 100 keV, dose 10 13 cm -2 and subsequent thermal annealing during 10 s) have been studied by means of photoreflection spectroscopy. Spectral lines of the crystal InP were absent in the photoreflection spectra of the samples annealed at temperatures less then 400 Deg C. This fact is connected with the disordering of the crystal structure due to the ion implantation. In the temperature range 400-700 Deg C the lines from InP band gap (1.34 eV) and conductance band-spin-orbit splitting valence subband (1.44 eV) have been observed due to the recovery of the crystal structure. In the photoreflectance spectra of a 800 Deg C annealed sample the Franz-Keldysh oscillations have been observed, which can be an evidence in favour of the dopant activation. Carrier concentration calculated from the period of Franz-Keldysh oscillations was equal to 2.2 x 10 16 cm -3 [ru

  16. High brightness InP micropillars grown on silicon with Fermi level splitting larger than 1 eV.

    Science.gov (United States)

    Tran, Thai-Truong D; Sun, Hao; Ng, Kar Wei; Ren, Fan; Li, Kun; Lu, Fanglu; Yablonovitch, Eli; Chang-Hasnain, Constance J

    2014-06-11

    The growth of III-V nanowires on silicon is a promising approach for low-cost, large-scale III-V photovoltaics. However, performances of III-V nanowire solar cells have not yet been as good as their bulk counterparts, as nanostructured light absorbers are fundamentally challenged by enhanced minority carriers surface recombination rates. The resulting nonradiative losses lead to significant reductions in the external spontaneous emission quantum yield, which, in turn, manifest as penalties in the open-circuit voltage. In this work, calibrated photoluminescence measurements are utilized to construct equivalent voltage-current characteristics relating illumination intensities to Fermi level splitting ΔF inside InP microillars. Under 1 sun, we show that splitting can exceed ΔF ∼ 0.90 eV in undoped pillars. This value can be increased to values of ΔF ∼ 0.95 eV by cleaning pillar surfaces in acidic etchants. Pillars with nanotextured surfaces can yield splitting of ΔF ∼ 0.90 eV, even though they exhibit high densities of stacking faults. Finally, by introducing n-dopants, ΔF of 1.07 eV can be achieved due to a wider bandgap energy in n-doped wurzite InP, the higher brightness of doped materials, and the extraordinarily low surface recombination velocity of InP. This is the highest reported value for InP materials grown on a silicon substrate. These results provide further evidence that InP micropillars on silicon could be a promising material for low-cost, large-scale solar cells with high efficiency.

  17. Effect of Yb substitution on room temperature magnetic and dielectric properties of bismuth ferrite nanoparticles

    Science.gov (United States)

    Remya, K. P.; Amirthapandian, S.; Manivel Raja, M.; Viswanathan, C.; Ponpandian, N.

    2016-10-01

    Effect of the Yb dopant on the structural, magnetic, and electrical properties of the multiferroic BiFeO3 have been studied. The structural properties of sol-gel derived Bi1-xYbxFeO3 (x = 0.0, 0.1, and 0.2) nanoparticles reveal the formation of a rhombohedrally distorted perovskite in XRD and a reduction in the average grain size have been observed with an increase in the Yb concentration. Microstructural studies exhibited the formation of sphere like morphology with decreasing particle size with increase in the dopant concentration. The effective doping also resulted in larger magnetization as well as coercivity with the maximum of 257 Oe and 1.76 emu/g in the Bi0.8Yb0.2FeO3 nanoparticles. Ferroelectric as well as dielectric properties of the nanoparticles were also improved on doping. The best results were obtained for the BiFeO3 nanoparticles having Yb concentration x = 0.2.

  18. Spectroscopic investigation of zinc tellurite glasses doped with Yb3 + and Er3 + ions

    Science.gov (United States)

    Bilir, Gökhan; Kaya, Ayfer; Cinkaya, Hatun; Eryürek, Gönül

    2016-08-01

    This paper presents a detailed spectroscopic investigation of zinc tellurite glasses with the compositions (0.80 - x - y) TeO2 + (0.20) ZnO + xEr2O3 + yYb2O3 (x = 0, y = 0; x = 0.004, y = 0; x = 0, y = 0.05 and x = 0.004, y = 0.05 per moles). The samples were synthesized by the conventional melt quenching method. The optical absorption and emission measurements were conducted at room temperature to determine the spectral properties of lanthanides doped zinc tellurite glasses and, to study the energy transfer processes between dopant lanthanide ions. The band gap energies for both direct and indirect possible transitions and the Urbach energies were measured from the absorption spectra. The absorption spectra of the samples were analyzed by using the Judd-Ofelt approach. The effect of the ytterbium ions on the emission properties of erbium ions was investigated and the energy transfer processes between dopant ions were studied by measuring the up-conversion emission properties of the materials. The color quality parameters of obtained visible up-conversion emission were also determined as well as possibility of using the Er3 + glasses as erbium doped fiber amplifiers at 1.55 μm in infrared emission region.

  19. When is an INP not an INP?

    Science.gov (United States)

    Simpson, Emma; Connolly, Paul; McFiggans, Gordon

    2016-04-01

    Processes such as precipitation and radiation depend on the concentration and size of different hydrometeors within clouds therefore it is important to accurately predict them in weather and climate models. A large fraction of clouds present in our atmosphere are mixed phase; contain both liquid and ice particles. The number of drops and ice crystals present in mixed phase clouds strongly depends on the size distribution of aerosols. Cloud condensation nuclei (CCN), a subset of atmospheric aerosol particles, are required for liquid drops to form in the atmosphere. These particles are ubiquitous in the atmosphere. To nucleate ice particles in mixed phase clouds ice nucleating particles (INP) are required. These particles are rarer than CCN. Here we investigate the case where CCN and INPs are in direct competition with each other for water vapour within a cloud. Focusing on the immersion and condensation modes of freezing (where an INP must be immersed within a liquid drop before it can freeze) we show that the presence of CCN can suppress the formation of ice. CCN are more hydrophilic than IN and as such are better able to compete for water vapour than, typically insoluble, INPs. Therefore water is more likely to condense onto a CCN than INP, leaving the INP without enough condensed water on it to be able to freeze in the immersion or condensation mode. The magnitude of this suppression effect strongly depends on a currently unconstrained quantity. Here we refer to this quantity as the critical mass of condensed water required for freezing, Mwc. Mwc is the threshold amount of water that must be condensed onto a INP before it can freeze in the immersion or condensation mode. Using the detailed cloud parcel model, Aerosol-Cloud-Precipiation-Interaction Model (ACPIM), developed at the University of Manchester we show that if only a small amount of water is required for freezing there is little suppression effect and if a large amount of water is required there is a

  20. Up-conversion monodispersed spheres of NaYF4:Yb3+/Er3+: green and red emission tailoring mediated by heating temperature, and greatly enhanced luminescence by Mn2+ doping.

    Science.gov (United States)

    Zhu, Qi; Song, Caiyun; Li, Xiaodong; Sun, Xudong; Li, Ji-Guang

    2018-04-09

    Submicron sized, monodispersed spheres of Mn2+, Yb3+/Er3+ and Mn2+/Yb3+/Er3+ doped α-NaYF4 were easily autoclaved from mixed solutions of the component nitrates and ammonium fluoride (NH4F), in the presence of EDTA-2Na. Detailed characterizations of the resultant phosphors were obtained using XRD, Raman spectroscopy, FE-SEM, HR-TEM, STEM, PLE/PL spectroscopy, and fluorescence decay analysis. Finer structure and better crystal perfection was observed at a higher calcination temperature, and the spherical shape and excellent dispersion of the original particles was retained at temperatures up to 600 °C. Under the 980 nm infrared excitation, the Yb3+/Er3+-doped sample (calcined at 400 °C) exhibits a stronger green emission centered at ∼524 nm (2H11/2 → 4I15/2 transition of Er3+) and a weaker red emission centered at ∼657 nm (4F9/2 → 4I15/2 transition of Er3+). A 200 °C increase in the temperature from 400 °C to 600 °C resulted in the dominant red emission originating from the 4F9/2 → 4I15/2 transition of Er3+, instead of the previously dominant green one. Mn2+ doping induced a remarkable more enhanced intensity at ∼657 nm and ∼667 nm (red emission area) than that at ∼524 nm and ∼546 nm (green emission area), because of the non-radiative energy transfer between Mn2+ and Er3+. However, a poor thermal stability was induced by Mn2+ doping. The observed upconversion luminescence of the samples calcined at 400 °C and 600 °C followed the two photon process and the four photon process, respectively.

  1. A comprehensive phononics of phonon assisted energy transfer in the Yb{sup 3+} aided upconversion luminescence of Tm{sup 3+} and Ho{sup 3+} in solids

    Energy Technology Data Exchange (ETDEWEB)

    Debnath, Radhaballabh, E-mail: drdebnathr@gmail.com; Bose, Saptasree

    2015-05-15

    The theory of phonon assisted energy transfer is being widely used to explain the Yb{sup 3+} ion aided normal and upconversion emission of various rare earth ions in different Yb{sup 3+} co-doped solids. The reported phonon dynamics in many of these studies are either incomplete or erroneous. Here we report Yb{sup 3+} aided upconversion luminescence properties of Tm{sup 3+} and Ho{sup 3+} in (Yb{sup 3+}/Tm{sup 3+}) and (Yb{sup 3+}/Ho{sup 3+}) co-doped two BaO–tellurite glasses and explain their phononics in the light of Dexter's theory by proposing a comprehensive scheme. The approach is valid for other systems of different phonon structures. - Highlights: • Yb{sup 3+} aided upconversion luminescence properties of Tm{sup 3+} and Ho{sup 3+} in (Yb{sup 3+}/Tm{sup 3+}) and (Yb{sup 3+}/Ho{sup 3+}) co-doped two BaO–tellurite glasses, are reported. • Phonon assisted energy transfer in these systems are explained in the light of Dexter's theory by proposing a comprehensive scheme of phononics. • The approach is valid for other systems of different phonon structures.

  2. Frequency upconversion fluorescence studies of Er{sup 3+}/Yb{sup 3+}-codoped KNbO{sub 3} phosphors

    Energy Technology Data Exchange (ETDEWEB)

    Balakrishnaiah, R. [Department of Electronic Materials Engineering, Silla University, Busan 617-736 (Korea, Republic of); Department of Physics, Changwon National University, Changwon 641-773 (Korea, Republic of); Kim, Dong Woo [Department of Electronic Materials Engineering, Silla University, Busan 617-736 (Korea, Republic of); Yi, Soung Soo, E-mail: ssyi@silla.ac.k [Department of Electronic Materials Engineering, Silla University, Busan 617-736 (Korea, Republic of); Kim, Kwang Duk; Kim, Sung Hoon [Department of Engineering in Energy and Applied Chemistry, Silla University, Busan 617-736 (Korea, Republic of); Jang, Kiwan; Lee, Ho Sueb [Department of Physics, Changwon National University, Changwon 641-773 (Korea, Republic of); Jeong, Jung Hyun [Department of Physics, Pukyong National University, Busan 608-737 (Korea, Republic of)

    2009-05-29

    Different concentrations of Er{sup 3+} and Yb{sup 3+} ions-doped potassium niobate (K{sub 0.9}NbO{sub 3}:Yb{sub (x)}Er{sub (0.1-x)} for x = 0, 0.01, 0.05, 0.09 and 0.1) polycrystalline powder phosphors were prepared by the conventional solid state reaction method and were characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM) techniques. Energy transfer and upconversion fluorescence properties of the Yb{sup 3+} and Er{sup 3+}-codoped phosphors have been discussed. The XRD data has shown mono-phase for pure KNbO{sub 3} while the doped samples represented additional phase formation. The SEM micrographs represented the rectangular crystal growth habit for the KNbO{sub 3} phosphors when doped with 0.1 mol of Er{sup 3+} ions. An intense green emission at 557 nm along with a red emission at 674 nm was observed when the doped samples were excited with 975 nm IR radiation. The upconversion mechanism has been discussed based on the excited state absorption and energy transfer mechanisms.

  3. Luminescence properties and energy transfer processes in YAG:Yb,Er single crystalline films

    International Nuclear Information System (INIS)

    Zorenko, Yu.; Gorbenko, V.; Savchyn, V.; Batentschuk, M.; Osvet, A.; Brabec, C.

    2013-01-01

    The paper is dedicated to the study of the optical properties of YAG:Yb,Er single-crystalline films (SCF) grown by liquid phase epitaxy. The absorption, cathodoluminescence and time-resolved photoluminescence spectra and photoluminescence decay curves were measured for the SCFs with different doping levels of Er 3+ (from 0.6 to 4.2 at.%) and Yb 3+ (from 0.1 to 0.6 at.%). The spectra, excited by synchrotron radiation in the fundamental absorption range of the YAG and in the intraionic absorption bands of both dopants, reveal energy transfer from the YAG host to the Er 3+ and Yb 3+ ions and between these ions. -- Highlights: •Growth of YAG:Yb,Er single crystalline films by LPE method. •Peculiarities of luminescence of YAG:Yb,Er films with different Er–Yb content. •Yb–Er energy transfer processes in YAG hosts

  4. Spectroscopic properties of Yb3+ and Er3+ ions in heavy metal glasses

    International Nuclear Information System (INIS)

    Pisarski, Wojciech A.; Grobelny, Lukasz; Pisarska, Joanna; Lisiecki, Radoslaw; Ryba-Romanowski, Witold

    2011-01-01

    Highlights: → Heavy metal glasses doubly doped with Yb 3+ and Er 3+ were examined. → NIR luminescence at about 1530 nm and green and red up-conversion spectra were detected. → The unusual large spectral linewidth nearly close to 110 nm for 4 I 13/2 - 4 I 15/2 transition of Er 3+ ions in Yb-Er co-doped lead borate glass was obtained. → Long-lived NIR luminescence was detected in lead germanate glass. → The NIR luminescence and up-conversion phenomena strongly depend on stretching vibrations of glass host. - Abstract: Selected heavy metal glasses containing Yb 3+ and Er 3+ ions have been studied. Near-infrared luminescence spectra at 1.53 μm and up-conversion spectra of Er 3+ ions were registered under excitation of Yb 3+ ions by 975 nm diode laser line. The luminescence bands correspond to 4 I 13/2 - 4 I 15/2 (NIR), 4 S 3/2 - 4 I 15/2 (green) and 4 F 9/2 - 4 I 15/2 (red) transitions of Er 3+ , respectively. The optical transitions of rare earth ions have been examined as a function of glass host. The unusual large spectral linewidth nearly close to 110 nm for 4 I 13/2 - 4 I 15/2 transition of Er 3+ ions in Yb-Er co-doped lead borate glass was obtained, whereas long-lived NIR luminescence at 1.53 μm was detected in lead germanate glass. The NIR luminescence and up-conversion phenomena strongly depend on stretching vibrations of glass host, which was confirmed by FT-IR spectroscopy.

  5. 5  W output power from a double-clad hybrid fiber with Yb-doped phosphate core and silicate cladding.

    Science.gov (United States)

    Wang, Longfei; He, Dongbing; Zhang, Lei; Yu, Chunlei; Feng, Suya; Wang, Meng; Chen, Danping; Hu, Lili

    2017-08-01

    For the first time, to the best of our knowledge, we report on the realization of a laser from a Yb-doped phosphate core/silicate cladding double-clad hybrid fiber. 5 W output power was extracted with 14.6% slope efficiency and a laser spectrum of a 1027 nm central wavelength from a 20 cm long single-mode fiber with a ∼10  μm core diameter in a 20%-4% laser cavity. The laser efficiency can be significantly enhanced by correspondingly adjusting and optimizing the laser oscillator.

  6. Upconversion emission and cathodoluminescence of Er{sup 3+}-doped NaYbF{sub 4} nanoparticles for low-temperature thermometry and field emission displays

    Energy Technology Data Exchange (ETDEWEB)

    Du, Peng; Yu, Jae Su [Kyung Hee University, Department of Electronics and Radio Engineering, Yongin (Korea, Republic of); Luo, Laihui [Ningbo University, Department of Microelectronic Science and Engineering, Ningbo (China)

    2017-03-15

    The Er{sup 3+}-doped NaYbF{sub 4} nanoparticles were fabricated by a hydrothermal method. The green and red emissions located at around 525, 542 and 657 nm corresponding to the {sup 2}H{sub 11/2} → {sup 4}I{sub 15/2}, {sup 4}S{sub 3/2} → {sup 4}I{sub 15/2} and {sup 4}F{sub 9/2} → {sup 4}I{sub 15/2} transitions of Er{sup 3+} ions, respectively, were observed when pumped at 980 nm light. Furthermore, with the help of the fluorescence intensity ratio technique, the thermometric properties of as-prepared products from the thermally coupled {sup 2}H{sub 11/2} and {sup 4}S{sub 3/2} levels of Er{sup 3+} ions were studied by analyzing temperature-dependent upconversion (UC) emission spectra. The maximum sensitivity for the Er{sup 3+}-doped NaYbF{sub 4} nanoparticles was found to be around 0.0043 K{sup -} {sup 1} with a temperature range of 93-293 K. In addition, the cathodoluminescence (CL) spectrum of the synthesized nanoparticles was nearly the same as the UC emission spectrum and the CL emission intensity did not exhibit saturation with the increase of accelerating voltage and filament current. (orig.)

  7. Preparation and up-conversion luminescence of SrAlF{sub 5}:Yb{sup 3+}/Er{sup 3+} nanorods

    Energy Technology Data Exchange (ETDEWEB)

    Zhao, Jun [College of Life Science, Dalian Nationalities University, Dalian, Liaoning 116600 (China); Department of Physics, Dalian Maritime University, Dalian, Liaoning 116026 (China); Hua, Ruinian, E-mail: rnhua@dlnu.edu.cn [College of Life Science, Dalian Nationalities University, Dalian, Liaoning 116600 (China); Zhang, Wei; Feng, Zhiqing; Tang, Dongxin; Na, Liyan [College of Life Science, Dalian Nationalities University, Dalian, Liaoning 116600 (China); Chen, Baojiu, E-mail: chenmbj@sohu.com [Department of Physics, Dalian Maritime University, Dalian, Liaoning 116026 (China)

    2014-03-05

    Graphical abstract: The SrAlF{sub 5} nanorods co-doped with various Yb{sup 3+}/Er{sup 3+} concentrations was synthetized via a microemulsion-hydrothermal process for the first time. It was found that the optimum doping concentration of Yb{sup 3+} and Er{sup 3+} in SrAlF{sub 5} matrix was about 4 mol%. Furthermore, the temperature effect of upconversion luminescence was investigated. It was also found that the post heat-treatment could greatly improve upconversion luminescence. Highlights: • SrAlF{sub 5}:Yb{sup 3+}/Er{sup 3+} nanorods were synthesized via a microemulsion-hydrothermal process. • Crystal structure and morphology were characterized by using XRD and FESEM. • The upconversion luminescence intensity depend on LD working current was studied. • The post heat-treatment could greatly improve upconversion luminescence. -- Abstract: Yb{sup 3+} and Er{sup 3+} co-doped SrAlF{sub 5} nanorods with average diameter of 35 nm and average length of 400 nm were synthesized via a microemulsion-hydrothermal process, and their crystal structure and morphology were characterized by using X-ray diffraction (XRD) and field emission scanning electron microscopy (FESEM), respectively. The optimum doping concentration of Yb{sup 3+}/Er{sup 3+} in SrAlF{sub 5} matrix was about 4 mol%. The upconversion luminescence intensity dependence on the laser diode (LD) working current was studied and the possible upconversion mechanism was analyzed. Furthermore, the temperature effect of upconversion luminescence was investigated. It was also found that the post heat-treatment could greatly improve upconversion luminescence.

  8. Upconversion emission study of Er3+/Yb3+ doped barium titanate phosphor prepared by co-precipitation method

    International Nuclear Information System (INIS)

    Mahata, M.K.; Dey, R.; Kumar, K.; Rai, V.K.; Rai, S.B.

    2012-01-01

    In the present work we have successfully synthesized the Er 3+ , Yb 3+ doped barium titanate phosphor via co-precipitation synthesis method. Under 980 nm excitation, tri-color upconversion fluorescence has been observed. The Fourier Transform Infrared measurement was done to check the presence of organic impurities. In order to find out how many photons are involved in each emission band, the variation of UC emission intensity of the codoped phosphor is studied with increase in excitation power. Upconversion emission spectra show that as the annealing temperature of the powder is increased, intensity of red emission decreases and intensity of green emission increases due to the decrease in maximum phonon frequency of the host material. (author)

  9. Upconversion studies of Er3+/Yb3+ doped SrO.TiO2 borosilicate glass ceramic system

    International Nuclear Information System (INIS)

    Maheshwari, Aditya; Om Prakash; Kumar, Devendra; Rai, S.B.

    2011-01-01

    Upconversion behaviour has been studied in various matrices and fine powders of SrTiO 3 by previous workers. In present work, Er 3+ /Yb 3+ were doped in appropriate ratio in SrO.TiO 2 borosilicate glass ceramic system to study the upconversion phenomenon. Dielectric properties of this class of glass ceramic system have been extensively investigated by Thakur et al. It has been observed that both upconversion efficiency and dielectric constant increases with transformation of glass into glass ceramic. Therefore, present investigation is based upon the study of optical as well as the electrical properties of same glass ceramic system. In order to prepare different crystalline matrices, two different Er 3+ /Yb 3+ :SrO.TiO 2 borosilicate glasses with same amount of Er 2 O 3 and Yb 2 O 3 were prepared by melt quench method. Glasses were transparent with light-wine colour. Glass ceramics were prepared from the glasses by heat treatment based on DTA (Differential thermal analysis) results. Glass ceramics were fully opaque with brownish-cream colour. Powder X-ray diffraction (XRD) patterns confirmed that two different crystalline matrices, Sr 3 Ti 2 O 7 , Ti 10 O 19 and SrTiO 3 , TiO 2 were present in two glass ceramic samples respectively. Luminescence properties of glass and glass ceramic samples with 976nm laser irradiation showed that the intensities of the green and red emission increased multiple times in glass ceramic than that of the glass. Possible mechanisms responsible for upconversion eg. Energy Transfer (ET) and Excited State Absorption (ESA), were studied through laser pumping power log dependence

  10. Optical Amplification at 1525 nm in BaYF5: 20% Yb3+, 2% Er3+ Nanocrystals Doped SU-8 Polymer Waveguide

    Directory of Open Access Journals (Sweden)

    Pengcheng Zhao

    2014-01-01

    Full Text Available We demonstrated optical amplification in BaYF5: 20% Yb3+, 2% Er3+ (BYF nanocrystals doped polymer waveguide. BYF nanocrystals with an average size of ∼13 nm were synthesized by a high-boiling solvent process. Intense 1.53 μm fluorescence was obtained in the nanocrystals under excitation at 980 nm. An optical polymer waveguide was fabricated by using BYF nanocrystals doped SU-8 polymer as the core material. A relative optical gain of ∼10.4 dB at 1525 nm was achieved in a 1.1 cm long waveguide for an input signal power of ∼0.09 mW and a pump power of ∼212 mW.

  11. Investigating the evolution of local structure around Er and Yb in ZnO:Er and ZnO:Er, Yb on annealing using X-ray absorption spectroscopy

    Science.gov (United States)

    Anjana, R.; Jayaraj, M. K.; Yadav, A. K.; Jha, S. N.; Bhattacharyya, D.

    2018-04-01

    The local structure around Er and Yb centre in ZnO favouring upconversion luminescence was studied using EXAFS (Extended X-ray absorption fine structure spectroscopy). Due to the ionic radii difference between Zn and Er, Yb ions, the dopants cannot replace Zn in the ZnO lattice properly. Er2O3 and Yb2O3 impurity phases are formed at the grain boundaries of ZnO. It is found that the local structure around the Er centre in ZnO is modified on annealing in air. The symmetry around both erbium and ytterbium reduces with increase in annealing temperature. Symmetry reduction will favour the intra-4f transition and the energy transitions causing upconversion luminescence. By fitting the EXAFS data with theoretically simulated data, it is found that the Er centre forms a local structure similar to C4ν symmetry which is a distorted octahedron. On annealing the sample to 1200 °C, all the erbium centres are transformed to C4ν symmetry causing enhanced upconversion emission. Yb centre has also been modified on annealing. The decrease in co-ordination number with annealing temperature will decrease the symmetry and increase the near infrared absorption cross section. The decrease in symmetry around both the erbium and ytterbium centre and formation of C4ν symmetry around Er centre is the reason behind the activation of upconversion luminescence with high temperature annealing in both Er doped and Er, Yb co-doped ZnO samples. The study will be useful for the synthesis of high efficiency upconversion materials.

  12. Growth and luminescent properties of Yb3+--doped oxide single crystals for scintillator application

    International Nuclear Information System (INIS)

    Yoshikawa, A.; Ogino, H.; Shim, J.B.; Nikl, M.; Solovieva, N.; Fukuda, T.

    2004-01-01

    Rod-shaped (Lu 1-x Yb x ) 3 Al 5 O 12 with x=0.05, 0.15, 0.30 and (Y 1-x Yb x )AlO 3 with x=0.05, 0.10, 0.30 single crystals were grown by the micro-pulling-down method. Edge-defined film-fed growth method was used to prepare (Y 0.9 Yb 0.1 )VO 4 crystal, while Ca 8 (La 1.98 Yb 0.02 )(PO 4 ) 6 O 2 crystal was grown by the Czochralski method. Luminescence of these crystals was studied with main attention paid to the charge transfer emission of Yb 3+ . Temperature tuned decay times in the time scale of units--tens of nanosecond was measured as a feature possibly interesting for an application in scintillation detectors in positron emission tomography

  13. Infrared emissions in MgSrAl{sub 10}O{sub 17}:Er{sup 3+} phosphor co-doped with Yb{sup 3+}/Ba{sup 2+}/Ca{sup 2+} obtained by solution combustion route

    Energy Technology Data Exchange (ETDEWEB)

    Singh, Vijay, E-mail: vijayjiin2006@yahoo.com [Physical Chemistry, Institute for Pure and Applied Chemistry and Center of Interface Science, University of Oldenburg, 26129 Oldenburg (Germany); Kumar Rai, Vineet [Department of Applied Physics, Indian School of Mines, Dhanbad 826 004 (India); Venkatramu, V. [Department of Physics, Yogi Vemana University, Kadapa 516 003 (India); Chakradhar, R.P.S. [CSIR-National Aerospace, Bangalore 560 017 (India); Hwan Kim, Sang [Department of Chemical Engineering, Konkuk University, Seoul 143-701 (Korea, Republic of)

    2013-02-15

    An intense infrared emitting MgSrAl{sub 10}O{sub 17}:Er{sup 3+} phosphor co-doped with Yb{sup 3+}, Ba{sup 2+} and Ca{sup 2+} ions have been prepared by a solution combustion method. Phase purity of the derived compounds was confirmed by X-ray diffraction technique. The vibrational properties of MgSrAl{sub 10}O{sub 17} phosphor was studied by Fourier transform infrared spectroscopy. The broad and strong infrared emission of Er{sup 3+} ions at around 1.53 {mu}m was observed upon excitation at 980 nm. Effect of co-doping with the Yb{sup 3+}{sub ,} Ba{sup 2+} and Ca{sup 2+} ions on the infrared luminescence intensity of Er{sup 3+} ions and the mechanism responsible for the variation in the infrared intensity have been discussed. The results indicate that these materials may be suitable for the optical telecommunication window and wavelength division multiplexing applications. - Highlights: Black-Right-Pointing-Pointer The hexagonal phase of MgSrAl{sub 10}O{sub 17} could be obtained by the low temperature combustion method. Black-Right-Pointing-Pointer The broad and strong infrared emission of Er{sup 3+} ions at around 1.53 {mu}m was observed. Black-Right-Pointing-Pointer Effect of co-doping with the Yb{sup 3+}{sub ,} Ba{sup 2+} and Ca{sup 2+} ions on the infrared luminescence intensity of Er{sup 3+} were reported.

  14. Growth of semiconductor alloy InGaPBi on InP by molecular beam epitaxy

    International Nuclear Information System (INIS)

    Wang, K; Wang, P; Pan, W W; Wu, X Y; Yue, L; Gong, Q; Wang, S M

    2015-01-01

    We report the first successful growth of InGaPBi single crystals on InP substrate with Bi concentration far beyond the doping level by gas source molecular beam epitaxy. The InGaPBi thin films reveal excellent surface and structural qualities, making it a promising new III–V compound family member for heterostructures. The strain can be tuned between tensile and compressive by adjusting Ga and Bi compositions. The maximum achieved Bi concentration is 2.2 ± 0.4% confirmed by Rutherford backscattering spectroscopy. Room temperature photoluminescence shows strong and broad light emission at energy levels much smaller than the InP bandgap. (paper)

  15. Investigation of Upconversion, downshifting and quantum –cutting behavior of Eu3+, Yb3+, Bi3+ co-doped LaNbO4 phosphor as a spectral conversion material

    Science.gov (United States)

    Dwivedi, A.; Mishra, K.; Rai, S. B.

    2018-06-01

    This work presents the spectral conversion characteristics [upconversion (UC), downshifting (DS) and quantum–cutting (QC) optical processes] of Eu3+, Yb3+ and Bi3+ co-doped LaNbO4 (LBO) phosphor samples synthesized by solid state reaction technique. The crystal structure and the pure phase formation have been confirmed by x-ray diffraction (XRD) measurements. The surface morphology and particle size are studied by scanning electron microscopy (SEM). The rarely observed intense red UC emission from Eu3+ ion has been successfully obtained in Eu3+/Yb3+ co-doped LaNbO4 phosphor (on excitation with 980 nm) by optimizing the concentrations of Eu3+ and Yb3+ ions. The downshifting (DS) behavior has been studied by photoluminescence (PL) measurements on excitation with 265 nm wavelength from a Xe lamp source. A broad blue emission in the region 300–550 nm with its maximum ∼415 nm due to charge transfer band (CTB) of the host and large number of sharp peaks due to f-f transitions of Eu3+ ion have been observed. The energy transfer has been observed from (NbO4)3‑ to Eu3+ ion and the fluorescence emission has been optimized by varying the concentration of Eu3+ ion. An intense red emission has also been observed corresponding to 5D0 → 7F2 transition of Eu3+ ion at 611 nm in LBO: 0.09Eu3+ phosphor on excitation with 394 nm. The luminescence properties of Eu3+ ion are enhanced further through the sensitization effect of Bi3+ ion. The near infra-red (NIR) quantum cutting (QC) behavior due to Yb3+ ion has been monitored on excitation with 265 as well as 394 nm. The NIR QC is observed due to 2F5/2 → 2F7/2 transition of Yb3+ ion via co-operative energy transfer (CET) process from (NbO4)3‑ as well as Eu3+ ions to Yb3+ ion. This multimodal behavior (UC, DS and QC) makes this a promising phosphor material for multi-purpose spectral converter.

  16. A femtosecond Yb-doped fiber laser with generalized vector vortex beams output (Conference Presentation)

    Science.gov (United States)

    Huo, Tiancheng; Qi, Li; Zhang, Buyun; Chen, Zhongping

    2017-03-01

    Light carries both spin and orbital angular momentum (OAM) and the superpositions of these two dynamical properties have found many applications. Many techniques exist to create such light sources but none allow their creation at the femtosecond fiber laser. Here we report on a novel mode-locked Ytterbium-doped fiber laser that generates femtosecond pulses with generalized vector vortex states. The controlled generation of such pulses such as azimuthally and radially polarized light with definite orbital angular momentum modes are demonstrated. A unidirectional ring cavity constructed with the Yb-doped fiber placed at the end of the fiber section to reduces unnecessary nonlinear effects is employed for self-starting operation. Pairs of diffraction gratings are used for compensating the normal group velocity dispersion of the fiber and other elements. Mode-locked operation is achieved based on nonlinear polarization evolution, which is mainly implemented with the single mode fiber, the bulk wave plates and the variable spiral plates (q-plate with topological charge q=0.5). The conversion from spin angular momentum to the OAM and reverse inside the laser cavity are realized by means of a quarter-wave plate and a q-plate so that the polarization control was mapped to OAM mode control. The fiber laser is diode pumped by a wavelength-division multiplexing coupler, which leads to excellent stability and portability.

  17. Spectroscopic investigation of zinc tellurite glasses doped with Yb(3+) and Er(3+) ions.

    Science.gov (United States)

    Bilir, Gökhan; Kaya, Ayfer; Cinkaya, Hatun; Eryürek, Gönül

    2016-08-05

    This paper presents a detailed spectroscopic investigation of zinc tellurite glasses with the compositions (0.80-x-y) TeO2+(0.20) ZnO+xEr2O3+yYb2O3 (x=0, y=0; x=0.004, y=0; x=0, y=0.05 and x=0.004, y=0.05 per moles). The samples were synthesized by the conventional melt quenching method. The optical absorption and emission measurements were conducted at room temperature to determine the spectral properties of lanthanides doped zinc tellurite glasses and, to study the energy transfer processes between dopant lanthanide ions. The band gap energies for both direct and indirect possible transitions and the Urbach energies were measured from the absorption spectra. The absorption spectra of the samples were analyzed by using the Judd-Ofelt approach. The effect of the ytterbium ions on the emission properties of erbium ions was investigated and the energy transfer processes between dopant ions were studied by measuring the up-conversion emission properties of the materials. The color quality parameters of obtained visible up-conversion emission were also determined as well as possibility of using the Er(3+) glasses as erbium doped fiber amplifiers at 1.55μm in infrared emission region. Copyright © 2016 Elsevier B.V. All rights reserved.

  18. Atomic frequency reference at 1033 nm for ytterbium (Yb)-doped fiber lasers and applications exploiting a rubidium (Rb) 5S_1/2 to 4D_5/2 one-colour two-photon transition

    Science.gov (United States)

    Roy, Ritayan; Condylis, Paul C.; Johnathan, Yik Jinen; Hessmo, Björn

    2017-04-01

    We demonstrate a two-photon transition of rubidium (Rb) atoms from the ground state (5$S_{1/2}$) to the excited state (4$D_{5/2}$), using a home-built ytterbium (Yb)-doped fiber amplifier at 1033 nm. This is the first demonstration of an atomic frequency reference at 1033 nm as well as of a one-colour two-photon transition for the above energy levels. A simple optical setup is presented for the two-photon transition fluorescence spectroscopy, which is useful for frequency stabilization for a broad class of lasers. This spectroscopy has potential applications in the fiber laser industry as a frequency reference, particularly for the Yb-doped fiber lasers. This two-photon transition also has applications in atomic physics as a background- free high- resolution atom detection and for quantum communication, which is outlined in this article.

  19. Up-conversion emission of Er{sup 3+}/Yb{sup 3+}co-doped BaBi{sub 2}Nb{sub 2}O{sub 9} (BBN) phosphors

    Energy Technology Data Exchange (ETDEWEB)

    Façanha, M.X., E-mail: marcello.facanha@uece.br [Departamento de Química, Centro de Ciências, Universidade Federal do Ceará (UFC), Fortaleza, Ceará (Brazil); Faculdade de Educação de Crateús (FAEC), Universidade Estadual do Ceará (UECE), Fortaleza, Ceará (Brazil); Laboratório de Telecomunicações e Ciências e Engenharia de Materiais (LOCEM), Universidade Federal do Ceará (UFC), Fortaleza, Ceará (Brazil); Nascimento, J.P.C. do [Departamento de Química, Centro de Ciências, Universidade Federal do Ceará (UFC), Fortaleza, Ceará (Brazil); Laboratório de Telecomunicações e Ciências e Engenharia de Materiais (LOCEM), Universidade Federal do Ceará (UFC), Fortaleza, Ceará (Brazil); Silva, M.A.S., E-mail: marceloassilva@yahoo.com.br [Laboratório de Telecomunicações e Ciências e Engenharia de Materiais (LOCEM), Universidade Federal do Ceará (UFC), Fortaleza, Ceará (Brazil); and others

    2017-03-15

    On this paper, polycrystalline samples of the tetragonal systems BaBi{sub 2}Nb{sub 2}O{sub 9} (BBN) and BBN co-doped with Er{sup 3+}/Yb{sup 3+} (BBN: 0.04Er{sup 3+}yYb{sup 3+}, where y=0.02, 0.04, 0.06 and 0.08 mol%) were synthesized by the solid state method. The crystalline structure and photoluminescent properties of the ceramic phosphors were investigated by powder X-ray diffraction (PXRD), Raman spectroscopy and spectral analysis of up-conversion (UC) emission. The results reveal that all compositions crystallize in the I4/mmm space group at room temperature, and show UC green emissions (centered at 525 nm and 550 nm) and red (around 660 nm) coming from ({sup 2}H{sub 11/2}, {sup 4}S{sub 3/2}→{sup 4}I{sub 15/2}) and ({sup 4}F{sub 9/2}→{sup 4}I{sub 15/2}) transitions, respectively, under excitation at 980 nm. Increasing variations of the Yb{sup 3+} sensitizer concentration in the host BBN, lead to a significant intensity increase in both UC emissions due to the efficiency of the energy-transfer process. The BBN: 0.04 mol%Er{sup 3+}0.08 mol%Yb{sup 3+} composition showed the higher intensity bands, thus establishing the BBN as an alternative host material for luminescent centers.

  20. The complexity of the CaF2:Yb system: evidence that CaF2:Yb2+ is not an impurity trapped exciton system

    Science.gov (United States)

    Mackeen, Cameron; Bridges, Frank; Kozina, Michael; Mehta, Apurva; Reid, M. F.; Wells, J.-P. R.; BarandiaráN, Zoila

    Fluorite crystal structures doped with rare-earth elements exhibit an anomalous redshifted luminescence upon UV excitation, generally attributed to the relaxation of impurity trapped excitons (ITE). We find that the intensity of this luminescence decreases as the total concentration of Yb 2+ increases in unexposed samples, which is in conflict with the currently accepted ITE model. Further, using x-ray absorption spectroscopy and UV-vis studies of CaF2:Yb, we find a large (but reversible) Yb valence reduction upon x-ray exposure at 200 K - from mostly 3+ to 2+. This valence reduction is stable for long time periods at low T ITE model; the data appear more consistent with an intervalence charge transfer (IVCT) model. It is likely that many similar ITE systems have also been misidentified.

  1. Highly matched spectrum needed for photosynthesis in Ce{sup 3+}/Er{sup 3+}/Yb{sup 3+} tri-doped oxyfluoride glass ceramics

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Weirong; Gao, Huiping [School of Physics and Electronics, Henan University, Kaifeng 475004 (China); Institute for Computational Materials Science, Henan University, Kaifeng 475004 (China); Mao, Yanli, E-mail: ylmao@henu.edu.cn [School of Physics and Electronics, Henan University, Kaifeng 475004 (China); Institute for Computational Materials Science, Henan University, Kaifeng 475004 (China)

    2015-11-05

    A series of oxyfluoride glass ceramics containing CaF{sub 2} nano-crystals tri-doped with Ce{sup 3+}/Er{sup 3+}/Yb{sup 3+} ions were prepared by high temperature melting method and subsequent heat treatment. The structural properties were examined by X-ray diffraction measurements. The absorption, excitation, and emission spectra of the glass ceramics were investigated. Difference in erbium emission spectra between glass and glass ceramics had been studied. The emission bands originating from the {sup 4}F{sub 9/2} state of Er{sup 3+} were enhanced when the CaF{sub 2} nano-crystal created. By down-converting the ultraviolet wavelength region (280∼400 nm) light and up-converting the near-infrared wavelength region (900∼1100 nm) light, the glass ceramics can also emit strong reddish orange emission. The emission spectra consisting of bluish violet (400∼500 nm) and reddish orange (640∼680 nm) bands match well with the action spectrum of photosynthesis and absorption spectra of chlorophylls. Our materials will be favored to promote the development of glass greenhouses for green plant. - Highlights: • Ce{sup 3+}/Er{sup 3+}/Yb{sup 3+} tri-doped oxyfluoride glass ceramics were prepared by high temperature melting method. • 668 nm red emission was obtained under 320 nm, 380 nm and 980 nm excitation, respectively. • The emission of samples matched well with the spectrum for photosynthesis.

  2. Indium-modified Yb:KLu(WO{sub 4}){sub 2} crystal: Growth, spectroscopy and laser operation

    Energy Technology Data Exchange (ETDEWEB)

    Serres, J.M. [Física i Cristallografia de Materials i Nanomaterials (FiCMA-FiCNA), Universitat Rovira i Virgili (URV), Campus Sescelades, c/ Marcellí Domingo, s/n., Tarragona E-43007 (Spain); Mateos, X., E-mail: xavier.mateos@urv.cat [Física i Cristallografia de Materials i Nanomaterials (FiCMA-FiCNA), Universitat Rovira i Virgili (URV), Campus Sescelades, c/ Marcellí Domingo, s/n., Tarragona E-43007 (Spain); Max Born Institute for Nonlinear Optics and Short Pulse Spectroscopy, 2A Max-Born-Str., Berlin D-12489 (Germany); Loiko, P. [ITMO University, 49 Kronverkskiy pr., St. Petersburg 197101 (Russian Federation); Griebner, U.; Petrov, V. [Max Born Institute for Nonlinear Optics and Short Pulse Spectroscopy, 2A Max-Born-Str., Berlin D-12489 (Germany); Yumashev, K. [Center for Optical Materials and Technologies (COMT), Belarusian National Technical University, 65/17 Nezavisimosti Ave., Minsk 220013 (Belarus); Aguiló, M.; Díaz, F. [Física i Cristallografia de Materials i Nanomaterials (FiCMA-FiCNA), Universitat Rovira i Virgili (URV), Campus Sescelades, c/ Marcellí Domingo, s/n., Tarragona E-43007 (Spain)

    2017-03-15

    We report on the growth, spectroscopic and laser characterization of a novel monoclinic laser crystal, Yb,In:KLu(WO{sub 4}){sub 2} (Yb,In:KLuW). The absorption, stimulated-emission and gain cross-section spectra of 3.5 at% Yb, 5.5 at% In-doped KLuW are determined at room temperature with polarized light and compared with those for Yb,In:KYW, as well as singly Yb-doped KLuW and KYW crystals. It is found that the introduction of In results in a decrease of the transition cross-sections and in a spectral broadening of the absorption and emission bands. Such a broadening is more pronounced for light polarization E ||N{sub p}. For Yb,In:KLuW, the maximum σ{sub abs} is 9.9×10{sup –20} cm{sup 2} at 980.9 nm for E ||N{sub m} and the corresponding bandwidth of the absorption peak is 3.7 nm. The radiative lifetime for Yb{sup 3+} ions is 237±5 µs. The stimulated-emission cross-sections are σ{sub SE}(m)=2.4×10{sup –20} cm{sup 2} at 1022.4 nm and σ{sub SE}(p)=1.3×10{sup –20} cm{sup 2} at 1039.1 nm corresponding to an emission bandwidth of >30 nm and >35 nm, respectively. The diode-pumped N{sub g}-cut Yb,In:KLuW microchip laser generated 4.11 W at 1042–1048 nm with a slope efficiency of 78%. The Yb,In:KLuW crystal is very promising for the generation of sub-100 fs pulses in mode-locked lasers due to its broadband emission characteristics.

  3. Infrared to near-infrared and visible upconversion mechanisms in LiYF 4: Yb3+, Ho3+

    NARCIS (Netherlands)

    Martín-Rodríguez, R.; Meijerink, A.|info:eu-repo/dai/nl/075044986

    2014-01-01

    Upconversion materials have regained interest in recent years due to their potential to enhance the efficiency of solar cells. The research has focused on lanthanide based upconverters, especially Er3+- and Yb 3+-doped materials. In this paper we report Ho3+ and Yb3+ upconversion after excitation

  4. Improving the photoluminescence response of Er-Tm: Al2O3 films by Yb codoping

    International Nuclear Information System (INIS)

    Xiao Zhisong; Serna, R.; Afonso, C.N.; Cheng Guoan; Vickridge, I.

    2007-01-01

    Amorphous Al 2 O 3 films doped with Er, Tm and Yb have been prepared by pulsed laser deposition. A broadband emission in the range 1400-1700 nm with two peaks around 1540 and 1640 nm has been observed, both in the Er-Tm and Er-Tm-Yb codoped films. The Tm-related photoluminescence (PL) intensity at 1640 nm is enhanced when codoping with Yb thus suggesting the existence of multiple energy transfer processes from Yb to Er and Er to Tm. The Er-Tm-Yb codoped film exhibits a broadband emission with a full-width half-maximum of 184 nm similar to that of the film codoped with Tm and Er but having higher Tm to Er concentration ratio and higher PL lifetime values

  5. Si Incorporation in InP Nanowires Grown by Au-Assisted Molecular Beam Epitaxy

    Directory of Open Access Journals (Sweden)

    Lorenzo Rigutti

    2009-01-01

    Full Text Available We report on the growth, structural characterization, and conductivity studies of Si-doped InP nanowires grown by Au-assisted molecular beam epitaxy. It is shown that Si doping reduces the mean diffusion length of adatoms on the lateral nanowire surface and consequently reduces the nanowire growth rate and promotes lateral growth. A resistivity as low as 5.1±0.3×10−5 Ω⋅cm is measured for highly doped nanowires. Two dopant incorporation mechanisms are discussed: incorporation via catalyst particle and direct incorporation on the nanowire sidewalls. The first mechanism is shown to be less efficient than the second one, resulting in inhomogeneous radial dopant distribution.

  6. Pulsed laser deposition and thermoelectric properties of In-and Yb-doped CoSb3 skutterudite thin films

    KAUST Repository

    Sarath Kumar, S. R.

    2011-07-29

    In-and Yb-doped CoSb3 thin films were prepared by pulsed laser deposition. Process optimization studies revealed that a very narrow process window exists for the growth of single-phase skutterudite films. The electrical conductivity and Seebeck coefficient measured in the temperature range 300-700 K revealed an irreversible change on the first heating cycle in argon ambient, which is attributed to the enhanced surface roughness of the films or trace secondary phases. A power factor of 0.68 W m-1 K-1 was obtained at ∼700 K, which is nearly six times lower than that of bulk samples. This difference is attributed to grain boundary scattering that causes a drop in film conductivity. Copyright © Materials Research Society 2011.

  7. Tunable multicolor and enhanced red emission of monodisperse CaF2:Yb3+/Ho3+ microspheres via Mn2+ doping

    Science.gov (United States)

    Wang, Rui; Yuan, Maohui; Zhang, Chaofan; Wang, Hongyan; Xu, Xiaojun

    2018-05-01

    Transition metal ions (e.g. Mn2+) and lanthanide co-doped upconversion (UC) materials have attracted wide attention in recent years due to their promising application in multicolor display. Here, we report the hydrothermal synthesis and characterization of Mn2+ doped monodisperse CaF2:Yb3+/Ho3+ microspheres. The results of X-ray diffraction (XRD) revealed that Mn2+ doping does not change the cubic phase of CaF2 material but will lead to diffraction peaks shifting slightly towards higher angle due to the substitution of larger Ca2+ by the relatively smaller Mn2+. Under the excitation of 980 nm continuous wave (CW) laser, these microspheres exhibit green-yellow-red tuning colors and remarkable enhancement of both red to green ratio (R/G) and red to blue ratio (R/B) when increasing Mn2+ concentration from 0 to 30 mol%. The energy migration process between Ho3+ and Mn2+ was proposed and supported by time-decay and power dependence measurements of Ho3+ UC emission. These upconversion materials may have potential applications in optical devices, color display, nanoscale lasers and biomedical imaging.

  8. Optical and magnetic properties of Yb ion-doped cobalt-based ZnO ...

    Indian Academy of Sciences (India)

    Administrator

    The X-ray photoelectron spectral peaks for Yb 4f ions ... temperature with high coercivity due to the contribution of both 3d and 4f exchange interaction with the host ... Mn,4,5 Co,6–9 Ni2,10 Fe11–13 and Cu,2,14 and reported to .... water separately under stirring. .... different concentrations of Yb added ZnO : Co, nanopar-.

  9. Fabrication of Y{sub 2}Ti{sub 2}O{sub 7}:Yb{sup 3+},Ho{sup 3+} nanoparticles by a gel-combustion approach and upconverting luminescent properties

    Energy Technology Data Exchange (ETDEWEB)

    Chen, Zhongsheng, E-mail: zhshcheng@ecit.cn [State Key Laboratory Breeding Base of Nuclear Resources and Environment, East China Institute of Technology, Nanchang, Jiangxi 330013 (China); Wang, Min; Wang, Haiqing; Le, Zhanggao; Huang, Guolin; Zou, Lixia; Liu, Zhirong [State Key Laboratory Breeding Base of Nuclear Resources and Environment, East China Institute of Technology, Nanchang, Jiangxi 330013 (China); Wang, Dianyuan; Wang, Qingkai [College of Science, Jiujiang University, Jiujiang, Jiangxi 332005 (China); Gong, Weiping [Electronic Science Department, Huizhou University, Huizhou, Guangdong 516001 (China)

    2014-09-01

    Highlights: • Co-doped (Y{sub 0.99−x}Ho{sub 0.01}Yb{sub x}){sub 2}Ti{sub 2}O{sub 7} nanophosphors were fabricated by gel-combustion method. • The effect of calcination and Yb{sup 3+} doping on upconverting spectra of nanophosphors was studied. • The dependence of upconverting intensity on the excitation power was examined. - Abstract: Yb{sup 3+}, Ho{sup 3+} co-doped pyrochlore-structured (Y{sub 0.99−x}Ho{sub 0.01}Yb{sub x}){sub 2}Ti{sub 2}O{sub 7} (x = 0, 2.5, 5.0, 7.5, 10.0 and 12.5 mol%) nanoparticles (NPs) were successfully fabricated via a gel-combustion approach. The products as-obtained were characterized by various techniques, i.e. X-ray diffraction, transmission electron microscope, Fourier transformed infrared spectra and upconverting spectra. The results indicate that the bright green (∼540 nm) and red (∼660 nm) emissions are observed in Y{sub 2}Ti{sub 2}O{sub 7}:Ho{sup 3+},Yb{sup 3+} NPs under the 980 nm excitation, which is ascribed to the radiative transitions ({sup 5}F{sub 4},{sup 5}S{sub 2}) → {sup 5}I{sub 8} and {sup 5}F{sub 5} → {sup 5}I{sub 8} of Ho{sup 3+} ions, respectively. It is also found that the calcining temperature and Yb{sup 3+} ion doping level have a great influence on the upconverting spectra of (Y{sub 0.99−x}Ho{sub 0.01}Yb{sub x}){sub 2}Ti{sub 2}O{sub 7} NPs. The emission intensities increase initially and then fall down from 800 to 1000 °C. The optimum doping level of Yb{sup 3+} ions is 7.5 mol%, and the intensity of upconverting emissions for (Y{sub 0.915}Ho{sub 0.01}Yb{sub 0.075}){sub 2}Ti{sub 2}O{sub 7} NPs is enhanced by the fold of 32 compared to the Yb{sup 3+}-free samples. The dependence of upconverting intensity on the excitation power reveals the contribution of two photons to both the green and red upconverting process under lower excitation power, and the possible upconverting mechanisms have been proposed accordingly.

  10. Lattice dynamics and substrate-dependent transport properties of (In, Yb)-doped CoSb3 skutterudite thin films

    KAUST Repository

    Sarath Kumar, S. R.

    2011-10-24

    Lattice dynamics, low-temperature electrical transport, and high-temperature thermoelectric properties of (In, Yb)-doped CoSb3thin films on different substrates are reported. Pulsed laser deposition under optimized conditions yielded single-phase polycrystalline skutterudite films. Raman spectroscopy studies suggested that In and Yb dopants occupy the cage sites in the skutterudite lattice. Low-temperature electrical transport studies revealed the n-type semiconducting nature of the films with extrinsic and intrinsic conduction mechanisms, in sharp contrast to the degenerate nature reported for identical bulk samples. Calculations yielded a direct bandgap close to 50 meV with no evidence of an indirect gap. The carrier concentration of the films was identical to that reported for the bulk and increased with temperature beyond 250 K. The higher resistivity exhibited is attributed to the enhanced grain boundary scattering in films with a high concentration of grains. The maximum power factor of ∼0.68 W m−1 K−1 obtained at 660 K for the film on glass is found to be nearly four times smaller compared to that reported for the bulk. The observed difference in the power factors of the films on different substrates is explained on the basis of the diffusion of oxygen from the substrates and the formation of highly conducting CoSb2 phase upon the oxidation of CoSb3.

  11. Continuous wave and tunable laser operation of Yb3+ in disordered NaLa(MoO4)2

    Science.gov (United States)

    Rico, M.; Liu, J.; Cano-Torres, J. M.; García-Cortés, A.; Cascales, C.; Zaldo, C.; Griebner, U.; Petrov, V.

    2005-09-01

    Continuous-wave Yb3+ laser operation is studied in single crystals of disordered NaLa(MoO4)2 at room temperature. The sample used was grown by the Czochralski technique and incorporates an Yb ion density of 3.1×1020 cm-3. The effect of the Yb concentration on some of the crystal properties is described as well as the spectroscopic Yb3+ properties at 5 K. Maximum slope efficiencies of about 40% for π and 38% for σ polarization were obtained under Ti:sapphire laser pumping near 976 nm, respectively. The maximum output power for the π polarization was 400 mW at 1039.5 nm, the threshold in this case amounted to 240 mW (absorbed pump power). The laser emission was tunable between 1016 and 1064 nm with a Lyot filter. Lasing was also realized by pumping with a fiber-coupled diode laser module. Maximum output power of 900 mW at 1035 nm was achieved in this case for the π polarization and the threshold was 280 mW. The results, in terms of output power and tunability, are superior in comparison to all previous reports on Yb-doped disordered double tungstate or molybdate crystals and represent a significant improvement in comparison to earlier experiments with low-doped Yb:NaLa(MoO4)2.

  12. Upconversion photoluminescence of epitaxial Yb{sup 3+}/Er{sup 3+} codoped ferroelectric Pb(Zr,Ti)O{sub 3} films on silicon substrates

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Yang, E-mail: zhangy_acd@hotmail.com [IFW Dresden, P.O. Box 270116, D-01171 Dresden (Germany); Kämpfe, Thomas [Institut für Angewandte Physik, TU Dresden, 01062 Dresden (Germany); Bai, Gongxun [Department of Applied Physics, The Hong Kong Polytechnic University, Hong Kong (China); Mietschke, Michael; Yuan, Feifei; Zopf, Michael [IFW Dresden, P.O. Box 270116, D-01171 Dresden (Germany); Abel, Stefan [IBM Research GmbH, Saümerstrasse 4, 8803 Rüschlikon (Switzerland); Eng, Lukas M. [Institut für Angewandte Physik, TU Dresden, 01062 Dresden (Germany); Hühne, Ruben [IFW Dresden, P.O. Box 270116, D-01171 Dresden (Germany); Fompeyrine, Jean [IBM Research GmbH, Saümerstrasse 4, 8803 Rüschlikon (Switzerland); Ding, Fei, E-mail: f.ding@ifw-dresden.de [IFW Dresden, P.O. Box 270116, D-01171 Dresden (Germany); Schmidt, Oliver G. [IFW Dresden, P.O. Box 270116, D-01171 Dresden (Germany); Material Systems for Nanoelectronics, Chemnitz University of Technology, Reichenhainer strasse 70, 09107 Chemnitz (Germany)

    2016-05-31

    Thin films of Yb{sup 3+}/Er{sup 3+} codoped Pb(Zr,Ti)O{sub 3} (PZT:Yb/Er) have been epitaxially grown on the SrTiO{sub 3} buffered Si wafer by pulsed laser deposition. Strong upconversion photoluminescence was observed in the PZT:Yb/Er thin film. Using piezoresponse force microscopy, polar domains in the PZT:Yb/Er film can be reversibly switched with a phase change of 180°. Ferroelectric hysteresis loop shape with a well-saturated response was observed. The epitaxially grown lanthanide-doped PZT on silicon opens up a promising route to the integration of luminescent functional oxides on the silicon platform. - Highlights: • Epitaxial growth of Yb{sup 3+}/Er{sup 3+} codoped Pb(Zr,Ti)O{sub 3} films on SrTiO{sub 3} buffered silicon • Upconversion emissions were obtained from the lanthanide ion doped thin films. • Saturated ferroelectric hysteresis loops were observed. • Polar domains were switched by PFM with a phase change of 180°.

  13. Effect of radiative trapping on measurement of the spectroscopic properties of Yb sup 3 sup + :phosphate glasses

    CERN Document Server

    Dai Shi Xun; Wen Lei; Hu Li Li; Jiang Zhong Hon

    2003-01-01

    The effect of radiative trapping on measurement of the spectroscopic properties of Yb sup 3 sup + -doped phosphate glasses was investigated as a function of Yb sup 3 sup + concentration at different thicknesses. It was found that radiative trapping exists generally in Yb sup 3 sup + :phosphate glasses, even at low concentration. As a result, the measured lifetime of Yb sup 3 sup + in phosphate glasses is usually larger than the calculated one. The maximum discrepancies between them at high concentration are found to be <42%. The calculated lifetime should be used as a reference in determining the true value of the measured lifetime because of it being lengthened largely by radiative trapping. On the other hand, the shape of fluorescence spectrum exhibits remarkable changes due to the radiative trapping. What is more, the intensity increase of DELTA lambda sub e sub f sub f at high concentration is greater than that of low doping. The DELTA lambda sub e sub f sub f increases 36% from 53 to 72 nm with thickn...

  14. Fingermark detection on non-porous and semi-porous surfaces using YVO4:Er,Yb luminescent upconverting particles.

    Science.gov (United States)

    Ma, Rongliang; Shimmon, Ronald; McDonagh, Andrew; Maynard, Philip; Lennard, Chris; Roux, Claude

    2012-04-10

    This article describes the use of an anti-Stokes luminescent material (upconverter), yttrium vanadate doped with ytterbium and erbium (YVO(4):Er,Yb), for the development of latent fingermarks on a range of non-porous surfaces. Anti-Stokes luminescent materials emit light at shorter wavelengths than the excitation wavelength. This property is unusual in both natural and artificial materials commonly found as exhibits in forensic science casework. As a result, fingermark detection techniques based on anti-Stokes luminescence are potentially extremely sensitive and selective. Latent fingermarks on non-luminescent and inherently luminescent substrates, including Australian polymer banknotes (a well-known 'difficult' surface), were developed with YVO(4):Er,Yb by dry powder and wet powder techniques. The effectiveness of YVO(4):Er,Yb for fingermark detection was compared with that of cyanoacrylate fuming and of sodium yttrium tetrafluoride doped with ytterbium and erbium (NaYF(4):Er,Yb). The results illustrate some benefit of luminescent up-converting phosphors over traditional luminescence techniques for the detection of latent fingermarks. Copyright © 2011 Elsevier Ireland Ltd. All rights reserved.

  15. Fiber-optic thermometer application of thermal radiation from rare-earth end-doped SiO2 fiber

    International Nuclear Information System (INIS)

    Katsumata, Toru; Morita, Kentaro; Komuro, Shuji; Aizawa, Hiroaki

    2014-01-01

    Visible light thermal radiation from SiO 2 glass doped with Y, La, Ce, Pr, Nd, Eu, Tb, Dy, Ho, Er, Tm, Yb, and Lu were studied for the fiber-optic thermometer application based on the temperature dependence of thermal radiation. Thermal radiations according to Planck's law of radiation are observed from the SiO 2 fibers doped with Y, La, Ce, Pr, Eu, Tb, and Lu at the temperature above 1100 K. Thermal radiations due to f-f transitions of rare-earth ions are observed from the SiO 2 fibers doped with Nd, Dy, Ho, Er, Tm, and Yb at the temperature above 900 K. Peak intensities of thermal radiations from rare-earth doped SiO 2 fibers increase sensitively with temperature. Thermal activation energies of thermal radiations by f-f transitions seen in Nd, Dy, Ho, Er, Tm, and Yb doped SiO 2 fibers are smaller than those from SiO 2 fibers doped with Y, La, Ce, Pr, Eu, Tb, and Lu. Thermal radiation due to highly efficient f-f transitions in Nd, Dy, Ho, Er, Tm, and Yb ions emits more easily than usual thermal radiation process. Thermal radiations from rare-earth doped SiO 2 are potentially applicable for the fiber-optic thermometry above 900 K

  16. Lifetimes Measurements in 160Yb,162Yb,164Yb,166Yb,168Yb

    International Nuclear Information System (INIS)

    Araddad, S. Y.; El-barouni, A. M.; Rateb, G. M.; Mosbah, D. S.; Elahrash, M. S.; Sergiwa, S. M.

    2004-01-01

    From our measurements of the lifetimes of high spin states in 168 Yb along with the published lifetime data for the nearby even even ytterbium isotopes, 160-168 Yb using the Recoil Distance Method (RDM) and the Doppler Shift Attenuation Method (DSAM) present a great opportunity to probe systematically the relationship between the nuclear shape changes and the reduction in collectivity. (authors)

  17. Optical reflectance studies of highly specular anisotropic nanoporous (111) InP membrane

    International Nuclear Information System (INIS)

    Steele, J A; Lewis, R A; Sirbu, L; Enachi, M; Tiginyanu, I M; Skuratov, V A

    2015-01-01

    High-precision optical angular reflectance measurements are reported for a specular anisotropic nanoporous (111) InP membrane prepared by doping-assisted wet-electrochemical etching. The membrane surface morphology was investigated using scanning electron microscope imaging and revealed a quasi-uniform and self-organized nanoporous network consisting of semiconductor ‘islands’ in the sub-wavelength regime. The optical response of the nanoporous InP surface was studied at 405 nm (740 THz; UV), 633 nm (474 THz; VIS) and 1064 nm (282 THz; NIR), and exhibited a retention of basic macro-dielectric properties. Refractive index determinations demonstrate an optical anisotropy for the membrane which is strongly dependent on the wavelength of incident light, and exhibits an interesting inversion (positive anisotropy to negative) between 405 and 633 nm. The inversion of optical anisotropy is attributed to a strongly reduced ‘metallic’ behaviour in the membrane when subject to above-bandgap illumination. For the simplest case of sub-bandgap incident irradiation, the optical properties of the nanoporous InP sample are analysed in terms of an effective refractive index n eff and compared to effective media approximations. (invited article)

  18. Micro-joule pico-second range Yb3+-doped fibre laser for medical applications in acupuncture

    Science.gov (United States)

    Alvarez-Chavez, J. A.; Rivera-Manrique, S. I.; Jacques, S. L.

    2011-08-01

    The work described here is based on the optical design, simulation and on-going implementation of a pulsed (Q-switch) Yb3+-doped, 1-um diffraction-limited fibre laser with pico-second, 10 micro-Joule-range energy pulses for producing the right energy pulses which could be of benefit for patients who suffer chronic headache, photophobia, and even nausea which could is sometimes triggered by a series of factors. The specific therapeutic effect known as acupunctural analgesia is the main objective of this medium-term project. It is a simple design on which commercially available software was employed for laser cavity design. Monte Carlo technique for skin light-transport, thermal diffusion and the possible thermal de-naturalization optical study and prediction will also be included in the presentation. Full optical characterization will be included and a complete set of recent results on the laser-skin interaction and the so called moxi-bustion from the laser design will be extensively described.

  19. Peculiarities of defect formation in InP single crystals doped with donor (S, Ge) and acceptor (Zn) impurities

    International Nuclear Information System (INIS)

    Morozov, A.N.; Mikryukova, E.V.; Bublik, V.T.; Berkova, A.V.; Nashel'skij, A.Ya.; Yakobson, S.V.

    1988-01-01

    Effect of alloying with donor (S,Ge) and acceptor (Zn) impurities on the concentration of proper point defects in monocrystals InP grown up from equiatomic (relative to In and P) melts by the Czochralski method under flux layer is investigated. Changes in boundary positions of the InP homogeneity region caused by alloying are analysed on the basis of experimental results according to the precision measurement of the lattice parameter and crystal density, as well as measurements of the Hall concentration of charge carriers and their mobility. The concentrations of Frenkel nonequilibrium (V in -In i ) defects formed in the initial stage of indium solid solution decomposition in InP are estimated

  20. Monolithic all-PM femtosecond Yb-doped fiber laser using photonic bandgap fibers

    DEFF Research Database (Denmark)

    Liu, Xiaomin; Lægsgaard, Jesper; Turchinovich, Dmitry

    2009-01-01

    We present a monolithic Yb fiber laser, dispersion managed by an all-solid photonic bandgap fiber, and pulse compressed in a hollow-core photonic crystal fiber. The laser delivers 9 nJ, 275-fs long pulses at 1035 nm.......We present a monolithic Yb fiber laser, dispersion managed by an all-solid photonic bandgap fiber, and pulse compressed in a hollow-core photonic crystal fiber. The laser delivers 9 nJ, 275-fs long pulses at 1035 nm....

  1. Minority-carrier lifetime in InP as a function of light bias

    Science.gov (United States)

    Yater, Jane A.; Weinberg, I.; Jenkins, Phillip P.; Landis, Geoffrey A.

    1995-01-01

    Minority-carrier lifetime in InP is studied as a function of doping level and laser intensity using time-resolved photoluminescence. A continuous wave diode laser illuminates bulk InP and acts as a light bias, injecting a steady-state concentration of carriers. A 200 ps laser pulse produces a small transient signal on top of the steady-state luminescence, allowing lifetime to be measured directly as a function of incident intensity. For p-InP, lifetime increases with light bias up to a maximum value. Bulk recombination centers are presumably filled to saturation, allowing minority carriers to live longer. The saturation bias scales with dopant concentration for a particular dopant species. As light bias is increased for n-InP, minority-carrier lifetime increases slightly but then decreases, suggesting radiative recombination as a dominant decay mechanism.

  2. The upconversion luminescence and magnetism in Yb{sup 3+}/Ho{sup 3+} co-doped LaF{sub 3} nanocrystals for potential bimodal imaging

    Energy Technology Data Exchange (ETDEWEB)

    Syamchand, Sasidharanpillai S., E-mail: syamchand.ss@gmail.com; George, Sony, E-mail: emailtosony@gmail.com [University of Kerala, Department of Chemistry (India)

    2016-12-15

    Biocompatible upconversion nanoparticles with multifunctional properties can serve as potential nanoprobes for multimodal imaging. Herein, we report an upconversion nanocrystal based on lanthanum fluoride which is developed to address the imaging modalities, upconversion luminescence imaging and magnetic resonance imaging (MRI). Lanthanide ions (Yb{sup 3+} and Ho{sup 3+}) doped LaF{sub 3} nanocrystals (LaF{sub 3} Yb{sup 3+}/Ho{sup 3+}) are fabricated through a rapid microwave-assisted synthesis. The hexagonal phase LaF{sub 3} nanocrystals exhibit nearly spherical morphology with average diameter of 9.8 nm. The inductively coupled plasma mass spectrometry (ICP-MS) analysis estimated the doping concentration of Yb{sup 3+} and Ho{sup 3+} as 3.99 and 0.41%, respectively. The nanocrystals show upconversion luminescence when irradiated with near-infrared (NIR) photons of wavelength 980 nm. The emission spectrum consists of bands centred at 542, 645 and 658 nm. The stronger green emission at 542 nm and the weak red emissions at 645 and 658 nm are assigned to {sup 5}S{sub 2} → {sup 5}I{sub 8} and {sup 5}F{sub 5} → {sup 5}I{sub 8} transitions of Ho{sup 3+}, respectively. The pump power dependence of luminescence intensity confirmed the two-photon upconversion process. The nanocrystals exhibit paramagnetism due to the presence of lanthanide ion dopant Ho{sup 3+} and the magnetization is 19.81 emu/g at room temperature. The nanocrystals exhibit a longitudinal relaxivity (r{sub 1}) of 0.12 s{sup −1} mM{sup −1} and transverse relaxivity (r{sub 2}) of 28.18 s{sup −1} mM{sup −1}, which makes the system suitable for developing T2 MRI contrast agents based on holmium. The LaF{sub 3} Yb{sup 3+}/Ho{sup 3+} nanocrystals are surface modified by PEGylation to improve biocompatibility and enhance further functionalisation. The PEGylated nanocrystals are found to be non-toxic up to 50 μg/mL for 48 h of incubation, which is confirmed by the MTT assay as well as

  3. Al2O3 influence on structural, elastic, thermal properties of Yb(3+) doped Ba-La-tellurite glass: evidence of reduction in self-radiation trapping at 1μm emission.

    Science.gov (United States)

    Balaji, S; Biswas, K; Sontakke, A D; Gupta, G; Ghosh, D; Annapurna, K

    2014-12-10

    Ba-La-tellurite glasses doped with Yb(3+) ions have been prepared through melt quenching technique by modifying their composition with the inclusion of varied concentration of Al2O3 to elucidate its effects on glass structural, elastic, thermal properties and Yb(3+) ion NIR luminescence performance. The FTIR spectral analysis indicates Al2O3 addition is promoting the conversion of BOs from NBOs which have been generated during the process of depolymerisation of main glass forming TeO4 units. The elastic properties of the glass revealed an improved rigidity of the glass network on addition of Al2O3. In concurrence to this, differential thermal analysis showed an increase in glass transition temperature with improved thermal stability factor. Also, Yb(3+) fluorescence dynamics demonstrated that, Al2O3 inclusion helps in restraining the detrimental radiation trapping of ∼1μm emission. Copyright © 2014 Elsevier B.V. All rights reserved.

  4. Photo darkening of rare earth doped silica

    DEFF Research Database (Denmark)

    Mattsson, Kent Erik

    2011-01-01

    /2/11/2 chemical bond is formed on dioxasilirane which comprises the PD color center for the visible and near-infrared. Difference in solid acidity of the silica material co-doped with Yb/Al and Yb/P may explain the observed difference in spectral shapes by change of bond order to the formed chemical bond. © 2011...

  5. Design, synthesis and luminescence properties of Ba2 YB2 O6 Cl- and Ba2 YB2 O6 F-based phosphors.

    Science.gov (United States)

    Chen, Wanping; Yang, Xin; Liu, Yan; Dai, Xiaoyan

    2015-05-01

    Using a high-temperature solid-state reaction, the chlorine in Ba2 YB2 O6 Cl is gradually replaced by F, and a new compound with the nominal chemical formula Ba2 YB2 O6 F and two phosphors doped with Ce(3+) and Eu(3+) , respectively, are obtained. X-Ray diffraction and photoluminescence spectroscopy are used to characterize the as-synthesized samples. The as-synthesized Ba2 YB2 O6 Cl exhibits bright blue emission in the spectral range ~ 330-410 nm with a maximum around 363 nm under X-ray or UV excitation. Ba2 YB2 O6 F:0.01Ce(3+) exhibits blue emission in the range ~ 340-570 nm with a maximum around 383 nm. Ba2 YB2 O6 F:0.01Eu(3+) exhibits a predominantly (5) D0 -(7)  F2 emission (~610 nm) and the relative intensities of the (5) D0 -(7)  F0,1,2 emissions are tunable under different wavelength UV excitation. The luminescence behaviors of the two phosphors are explained simply in terms of the host composition and site occupancy probability of Ce(3+) and Eu(3+) , respectively. The results indicate that these phosphors have potential application as a blue phosphor or as a red phosphor. Copyright © 2014 John Wiley & Sons, Ltd.

  6. Lattice location of diffused Zn atoms in GaAs and InP single crystals

    International Nuclear Information System (INIS)

    Chan, L.Y.; Yu, K.M.; Ben-Tzur, M.; Haller, E.E.; Jaklevic, J.M.; Walukiewicz, W.; Hanson, C.M.

    1991-01-01

    We have investigated the saturation phenomenon of the free carrier concentration in p-type GaAs and InP single crystals doped by zinc diffusion. The free hole saturation occurs at 10 20 cm -3 for GaAs, but the maximum concentration for InP appears at mid 10 18 cm -3 . The difference in the saturation hole concentrations for these materials is investigated by studying the incorporation and the lattice location of the impurity zinc, an acceptor when located on a group III atom site. Zinc is diffused into the III-V wafers in a sealed quartz ampoule. Particle-induced x-ray emission with ion-channeling techniques are employed to determine the exact lattice location of the zinc atoms. We have found that over 90% of all zinc atoms occupy Ga sites in the diffused GaAs samples, while for the InP case, the zinc substitutionality is dependent on the cooling rate of the sample after high-temperature diffusion. For the slowly cooled sample, a large fraction (∼90%) of the zinc atoms form random precipitates of Zn 3 P 2 and elemental Zn. However, when rapidly cooled only 60% of the zinc forms such precipitates while the rest occupies specific sites in the InP. We analyze our results in terms of the amphoteric native defect model. We show that the difference in the electrical activity of the Zn atoms in GaAs and InP is a consequence of the different location of the Fermi level stabilization energy in these two materials

  7. Growth and characterization of Yb:Ho:YAG single crystal fiber

    Science.gov (United States)

    Yang, Yilun; Ye, Linhua; Bao, Renjie; Li, Shanming; Zhang, Peixiong; Xu, Min; Hang, Yin

    2018-06-01

    High quality Yb and Ho co-doped Y3Al5O12 single crystal fibers have been successfully grown by the laser heated pedestal growth method of up to 124 mm in length and 450 μm in diameter for the first time. The results of inductively coupled plasma-atomic emission spectrometry analysis, X-ray diffraction and Raman spectroscopy reveal that the lattice structure and doping concentrations of the SCF are the same as that of the bulk. Scanning electron microscopy microphotographs shows that the fibers only have minor diameter fluctuations within 0.5%.

  8. High-efficiency cavity-dumped micro-chip Yb:YAG laser

    Science.gov (United States)

    Nishio, M.; Maruko, A.; Inoue, M.; Takama, M.; Matsubara, S.; Okunishi, H.; Kato, K.; Kyomoto, K.; Yoshida, T.; Shimabayashi, K.; Morioka, M.; Inayoshi, S.; Yamagata, S.; Kawato, S.

    2014-09-01

    High-efficiency cavity-dumped ytterbium-doped yttrium aluminum garnet (Yb:YAG) laser was developed. Although the high quantum efficiency of ytterbium-doped laser materials is appropriate for high-efficiency laser oscillation, the efficiency is decreased by their quasi-three/four laser natures. High gain operation by high intensity pumping is suitable for high efficiency oscillation on the quasi-three/four lasers without extremely low temperature cooling. In our group, highest efficiency oscillations for continuous wave, nanosecond to picosecond pulse lasers were achieved at room temperature by the high gain operation in which pump intensities were beyond 100 kW/cm2.

  9. Monte Carlo investigation of minority electron transport in InP

    International Nuclear Information System (INIS)

    Osman, M.A.; Grubin, H.L.

    1989-01-01

    This paper discusses the investigation of the transport of minority electrons in p-type InP for acceptor doping level of 10 18 cm 3 using Monte Carlo procedures. It is found that the velocity of minority electrons are significantly lower than that of majority electrons for fields below 15 kV/cm and slightly higher at higher fields. The study shows that the interaction between the electrons and majority holes leads to reducing the mobility of electrons from 2000 cm 2 /Vs to 1500 cm 2 /Vs

  10. Diode-pumped Yb:Sr5(PO4)3F laser performance

    International Nuclear Information System (INIS)

    Marshall, C.D.; Payne, S.A.; Smith, L.K.

    1995-01-01

    The performance of the first diode-pumped Yb 3+ -doped Sr 5 (PO 4 ) 3 F (Yb:S-FAP) laser is discussed. We found the pumping dynamics and extraction cross-sections of Yb:S-FAP crystals to be similar to those previously inferred by purely spectroscopic techniques. The saturation fluence for pumping was measured to be 2.2 J/cm 2 using three different methods based on either the spatial, temporal, or energy transmission properties of a Yb:S-FAP rod. The small signal gain implies an emission cross section of 6.0 x 10 -20 cm 2 that falls within error bars of the previously reported value of 7.3 x 10 -20 cm 2 , obtained from spectroscopic techniques. Up to 1.7 J/cm 3 of stored energy density was achieved in a 6 x 6 x 44 mm Yb:S-FAP amplifier rod. An InGaAs diode array has been fabricated that has suitable specifications for pumping a 3 x 3 x 30 mm Yb:S-FAP rod. In a free running configuration diode-pumped slope efficiencies up to 43% were observed with output energies up to ∼0.5 J per 1 ms pulse. When the rod was mounted in a copper block for cooling, 13 W of average power was produced with power supply limited operation at 70 Hz and 500 μs pulses

  11. Near-infrared photoluminescence in La0.98AlO3: 0.02Ln3+(Ln = Nd/Yb) for sensitization of c-Si solar cells

    Science.gov (United States)

    Sawala, N. S.; Koparkar, K. A.; Bajaj, N. S.; Omanwar, S. K.

    2016-05-01

    The host matrix LaAlO3 was synthesized by conventional solid state reaction method in which the Nd3+ ions and Yb3+ ions successfully doped at 2mol% concentrations. The phase purity was confirmed by X ray powder diffraction (XRD) method. The photoluminescence (PL) properties were studied by spectrophotometer in near infra red (NIR) and ultra violet visible (UV-VIS) region. The Nd3+ ion doped LaAlO3 converts a visible (VIS) green photon (587 nm) into near infrared (NIR) photon (1070 nm) while Yb3+ ion doped converts ultra violet (UV) photon (221 nm) into NIR photon (980 nm). The La0.98AlO3: 0.02Ln3+(Ln = Nd / Yb) can be potentiality used for betterment of photovoltaic (PV) technology. This result further indicates its potential application as a luminescence converter layer for enhancing solar cells performance.

  12. Highly scalable, resonantly cladding-pumped, Er-doped fiber laser with record efficiency.

    Science.gov (United States)

    Dubinskii, M; Zhang, J; Ter-Mikirtychev, V

    2009-05-15

    We report the performance of a resonantly cladding-pumped, Yb-free, Er-doped fiber laser. We believe this is the first reported resonantly cladding-pumped fiber-Bragg-grating-based, Er-doped, large-mode-area (LMA) fiber laser. The laser, pumped by fiber-coupled InGaAsP/InP laser diode modules at 1,532.5 nm, delivers approximately 48 W of cw output at 1,590 nm. It is believed to be the highest power ever reported from a Yb-free Er-doped LMA fiber. This fully integrated laser also has the optical-to-optical efficiency of approximately 57%, to the best of our knowledge, the highest efficiency reported for cladding-pumped unidirectionally emitting Er-doped laser.

  13. Spectroscopic properties of Er3+/Yb3+ Co-doped zinc boro-tellurite glasses for 1.5 xB5m broadband optical amplifiers

    Science.gov (United States)

    Suthanthirakumar, P.; Karthikeyan, P.; Vijayakumar, R.; Marimuthu, K.

    2015-06-01

    A new series of Er3+/Yb3+ co-doped Zinc boro-tellurite glasses with the chemical composition (40-x-y)B2O3+ 25TeO2+20ZnO+15BaO+xYb2O3+yEr2O3 (where x = 0.1, 0.5, 1 and 3; y =1 in wt %) were prepared by melt quenching technique and their spectroscopic behavior were studied through UV-Vis-NIR absorption and NIR luminescence measurements. The bonding parameters (β ¯ and δ) and Judd-Ofelt (JO) intensity parameters Ωλ (λ=2, 4 and 6) have been calculated from the band positions of the absorption spectra. A broad near-infrared emission band at 1540 nm with a full width at half maximum around 80 nm was observed from the NIR luminescence spectra by monitoring an excitation at 980 nm. The absorption cross-section and emission cross-section for the4I13/2→4I15/2 transition of the Er3+ ions were also determined using McCumber theory and the results were discussed and reported.

  14. Efficient green and red up-conversion emissions in Er/Yb co-doped TiO{sub 2} nanopowders prepared by hydrothermal-assisted sol–gel process

    Energy Technology Data Exchange (ETDEWEB)

    Salhi, Rached, E-mail: salhi_rached@yahoo.fr [Laboratoire de chimie industrielle, Ecole Nationale d’ingénieurs de Sfax, Université de Sfax, 3018 Sfax (Tunisia); Deschanvres, Jean-Luc [Laboratoire des Matériaux et du Génie Physique, 3 Parvis Louis Néel, BP 257, 38016 Grenoble (France)

    2016-08-15

    In this work, erbium and ytterbium co-doped titanium dioxide (Er–Yb:TiO{sub 2}) nanopowders have been successfully prepared by hydrothermal-assisted sol–gel method using supercritical drying of ethyl alcohol and annealing at 500 °C for 1 h. Nanopowders were prepared with fixed 5 mol% Erbium concentration and various Ytterbium concentrations of 5 and 10 mol%. The powders were characterized by studying their structural, morphology and photo-luminescent properties. The annealing treatment at 500 °C was found to enhance the crystallinity of the TiO{sub 2} anatase structure and the upconversion (UC) emission of the nanopowders. UC emissions were investigated under 980 nm excitation, and the Er–Yb:TiO{sub 2} nanopowders exhibited the intense green (520–570 nm) and red (640–690 nm) upconverted emissions of Er ions originating from an efficient Yb–Er energy transfer process. The absolute upconversion quantum yield (UC-QY) of each nanopowders was measured for the UC emissions centered at 525, 550 and 655 nm at varying excitation power densities. UC-QY analysis has revealed that 5 mol% Er–5 mol% Yb:TiO{sub 2} nanopowders possess the highest total quantum yield of 2.8±0.1% with a power density of 16.7 W/cm{sup 2}. These results make these nanopowders promising materials for efficient upconversion in photonic applications.

  15. Near infra red light emitting Y2Sn2O7: Yb-Er nanoparticles

    International Nuclear Information System (INIS)

    Nigam, Sandeep; Sudarsan, V.; Vatsa, R.K.

    2011-01-01

    There is an increasing interest in erbium doped nanomaterials host, since they emit in the near-infrared region and are potential candidates for optical telecommunication, high-power and infrared lasers. Further, erbium-ytterbium-co-doped matrices have been particularly investigated as Yb 3+ ions play the role of sensitizers. In the present work, Y 2 Sn 2 O 7 nanoparticles co-doped with lanthanide ions Yb 3+ and Er 3+ were prepared based on the urea hydrolysis of Y 3+ , Sn 4+ , and Ln 3+ in ethylene glycol medium at 150 deg C followed by heating at 700 deg C. As prepared samples are amorphous in nature, and the sample heated at 700 deg C showed well crystalline pyrochlore structure. Based on TEM studies, it has been established that nano-particles are highly crystalline, with size range in the range of 2-5 nm. Luminescence measurements were carried out for the as prepared samples and those heated at 700 deg C. As prepared sampled showed very poor luminescence. However on heating to 700 deg C, strong emission in the NIR region was observed upon UV-excitation as can be seen. The peak observed around 1530 nm has been attributed to 4 I 13/2 → 4 I 15/2 transition of Er 3+ and the peak around 980 nm is due to 2 F 5/2 → 2 F 7/2 transition of Yb 3+ . (author)

  16. Effects of Er{sup 3+} and Yb{sup 3+} doping on structural and non-linear optical properties of LiNaSO{sub 4}

    Energy Technology Data Exchange (ETDEWEB)

    Palmero, I.C. [Departamento de Fisica Basica, Electronica y Sistemas, Universidad de La Laguna, E-38200, San Cristobal de la Laguna, Santa Cruz de Tenerife (Spain); Gonzalez-Silgo, C. [Departamento de Fisica Fundamental II, Electronica y Sistemas, Universidad de La Laguna, E-38200, San Cristobal de la Laguna, Santa Cruz de Tenerife (Spain); Torres, M.E. [Departamento de Fisica Basica, Electronica y Sistemas, Universidad de La Laguna, E-38200, San Cristobal de la Laguna, Santa Cruz de Tenerife (Spain); Marrero-Lopez, D. [Departamento de Quimica Inorganica, Electronica y Sistemas, Universidad de La Laguna, E-38200, San Cristobal de la Laguna, Santa Cruz de Tenerife (Spain); Rivera-Lopez, Fernando [Departamento de Fisica Fundamental y Experimental, Electronica y Sistemas, Universidad de La Laguna, E-38200, San Cristobal de la Laguna, Santa Cruz de Tenerife (Spain)], E-mail: frivera@ull.es; Haro-Gonzalez, P. [Departamento de Fisica Fundamental y Experimental, Electronica y Sistemas, Universidad de La Laguna, E-38200, San Cristobal de la Laguna, Santa Cruz de Tenerife (Spain); Solans, X. [Departament de Cristallografia, Universitat de Barcelona, E-08028, Barcelona (Spain)

    2008-05-15

    We have characterized LiNaSO{sub 4} crystals doped with rare earth (RE) (Er{sup 3+} and Yb{sup 3+}) to give new insights about their structural properties relations. The samples were analyzed by X-ray single crystal diffraction and differential thermal analysis. The non-centrosymmetry was confirmed second-harmonic generation. Inductively coupled plasma (ICP) and emission experiments confirmed the nominal concentrations of the REs. Crystallographic data and two empirical models were employed to understand the structural modifications by substitution of the Na site which reduces, monotonically, the non-linear optical coefficients and the temperature of the phase transition in these crystals.

  17. Peptides for functionalization of InP semiconductors.

    Science.gov (United States)

    Estephan, Elias; Saab, Marie-belle; Larroque, Christian; Martin, Marta; Olsson, Fredrik; Lourdudoss, Sebastian; Gergely, Csilla

    2009-09-15

    The challenge is to achieve high specificity in molecular sensing by proper functionalization of micro/nano-structured semiconductors by peptides that reveal specific recognition for these structures. Here we report on surface modification of the InP semiconductors by adhesion peptides produced by the phage display technique. An M13 bacteriophage library has been used to screen 10(10) different peptides against the InP(001) and the InP(111) surfaces to finally isolate specific peptides for each orientation of the InP. MALDI-TOF/TOF mass spectrometry has been employed to study real affinity of the peptide towards the InP surfaces. The peptides serve for controlled placement of biotin onto InP to bind then streptavidin. Our Atomic Force Microscopy study revealed a total surface coverage of molecules when the InP surface was functionalized by its specific biotinylated peptide (YAIKGPSHFRPS). Finally, fluorescence microscopy has been employed to demonstrate the preferential attachment of the peptide onto a micro-patterned InP surface. Use of substrate specific peptides could present an alternative solution for the problems encountered in the actually existing sensing methods and molecular self-assembly due to the unwanted unspecific interactions.

  18. Highly Yb-doped KGd(WO4)2 thin-film amplifier

    NARCIS (Netherlands)

    Yong, Yean Sheng; Aravazhi, S.; Vázquez-Córdova, Sergio Andrés; García Blanco, Sonia Maria; Pollnau, Markus

    We report record-high small-signal gain of 1050 dB/cm at 981 nm wavelength in a KGd0.425Yb0.575(WO4)2 thin film. The sensitivity of gain to the shift of beam-focus position, which is critical under non-waveguiding conditions, is investigated.

  19. Role of electrode metallization in the performance of bulk semi-insulating InP radiation detectors

    International Nuclear Information System (INIS)

    Zatko, B.; Dubecky, F.; Prochazkova, O.; Necas, V.

    2007-01-01

    This work deals with the study of three different electrode metallizations with the aim to form a Schottky barrier contact. Electrode geometry corresponds to the requirements of digital radiography systems. As substrates bulk Liquid Encapsulated Czochralski (LEC) SI InP wafers doped with Fe and Fe+Zn are used. Results of this study show that no one of the used metallization performs as a blocking contact. However, detectors with Ti/Pt/Au metallization attained a relatively good energy resolution of 7.0 keV in full-width at half-maximum (FWHM) and the charge collection efficiency (CCE) higher than 83% for 122 keV γ-photons at 255 K. The development of SI InP radiation detectors and in particular their electrode technology is discussed in the light of observed results

  20. Synthesis and characterization of KY3F10 and KY3F10:Yb:Nd:Tm crystals for optical applications

    International Nuclear Information System (INIS)

    Linhares, Horacio Marconi da Silva Dantas

    2009-01-01

    In this work, crystals of KY 3 F 10 pure and doped with Yb, Nd and Tm were grown aiming at the attainment of blue emission via Tm 3+ ions up conversion. It was established the best conditions to synthesis and purification of KY 3 F 10 . Crystals doped with 1.3 mol% Nd, 0.5 mol% Tm and some concentrations of Yb (5, 10, 20, 30 and 40 mol%) were obtained by slow cooling of the charge from the melt, using an usual conventional synthesis system and in a reactive HF atmosphere. It was taken into account parameters as cooling rate and different configurations of boats to conditioning the materials. The limit of Yb concentration to obtain a unique cubic phase was determined as 30mol%, for the cooling rates used in this work. The physical and chemical characterizations of the samples were performed by X-ray diffraction, differential thermal analysis, inductively coupled plasma-optical emission spectroscopy (ICP-OES), scanning electron microscopy, optical absorption and emission. An initial spectroscopic study was performed to verify the effect of the Yb 3+ concentration regarding the blue emission efficiency in the KY 3 F 10 :Yb:Nd:Tm. When the Nd 3+ is pumped at 797 nm, it was determined that the suitable Yb concentrations are between 10 and 20 mol% to obtain blue emission at 480 nm, and between 20 and 30 mol% to obtain emission at 450 nm. It was observed that two emissions bands in the UV (350 and 360nm) enhanced proportionally with the Yb 3+ concentration. (author)

  1. Ionic conductivity of co-doped Sc2O3-ZrO2 ceramics

    DEFF Research Database (Denmark)

    Omar, Shobit; bin Najib, Waqas; Chen, Weiwu

    2012-01-01

    The oxide ionic conductivity of Sc0.18Zr0.82O1.91 doped with 0.5 mol.% of both Yb2O3 and In2O3 is evaluated at various temperatures in air. Among various co-doped compositions, In0.02Sc0.18Zr0.80O1.90 exhibits the highest grain ionic conductivity followed by Yb0.02Sc0.18Zr0.80O1.90 at 500°C....... However, it also possesses phase transformation from c- to β-phase at 475°C on cooling. In the present work, an attempt is made to completely stabilize the cphase in In0.02Sc0.18Zr0.80O1.90 by substituting 0.5 mol.% of In2O3 with Yb2O3, which can enhance the ionic conductivity in co-doped compositions....

  2. Remote Water Temperature Measurements Based on Brillouin Scattering with a Frequency Doubled Pulsed Yb:doped Fiber Amplifier

    Directory of Open Access Journals (Sweden)

    Thomas Walther

    2008-09-01

    Full Text Available Temperature profiles of the ocean are of interest for weather forecasts, climate studies and oceanography in general. Currently, mostly in situ techniques such as fixed buoys or bathythermographs deliver oceanic temperature profiles. A LIDAR method based on Brillouin scattering is an attractive alternative for remote sensing of such water temperature profiles. It makes it possible to deliver cost-effective on-line data covering an extended region of the ocean. The temperature measurement is based on spontaneous Brillouin scattering in water. In this contribution, we present the first water temperature measurements using a Yb:doped pulsed fiber amplifier. The fiber amplifier is a custom designed device which can be operated in a vibrational environment while emitting narrow bandwidth laser pulses. The device shows promising performance and demonstrates the feasibility of this approach. Furthermore, the current status of the receiver is briefly discussed; it is based on an excited state Faraday anomalous dispersion optical filter.

  3. Broadband down-conversion based near infrared quantum cutting in Eu{sup 2+}–Yb{sup 3+} co-doped SrAl{sub 2}O{sub 4} for crystalline silicon solar cells

    Energy Technology Data Exchange (ETDEWEB)

    Tai, Yuping, E-mail: yupingtai@126.com [Key Laboratory of Synthetic and Natural Functional Molecule Chemistry (Ministry of Education), College of Chemistry & Materials Science, Northwest University, Xi’an 710069 (China); Zheng, Guojun, E-mail: zhengguojun88@126.com [Key Laboratory of Synthetic and Natural Functional Molecule Chemistry (Ministry of Education), College of Chemistry & Materials Science, Northwest University, Xi’an 710069 (China); Wang, Hui, E-mail: huiwang@nwu.edu.cn [Key Laboratory of Synthetic and Natural Functional Molecule Chemistry (Ministry of Education), College of Chemistry & Materials Science, Northwest University, Xi’an 710069 (China); National Key Laboratory of Photoelectric Technology and Functional Materials Culture Base, National Photoelectric Technology and Functional Materials & Application of International Science and Technology Cooperation Base, Institute of Photonics & Photon-Technology, Northwest University, Xi' an 710069 (China); Bai, Jintao, E-mail: baijt@nwu.edu.cn [National Key Laboratory of Photoelectric Technology and Functional Materials Culture Base, National Photoelectric Technology and Functional Materials & Application of International Science and Technology Cooperation Base, Institute of Photonics & Photon-Technology, Northwest University, Xi' an 710069 (China)

    2015-03-15

    Near infrared (NIR) quantum cutting involving the down conversion of an absorbed visible photon to emission of two NIR photons was achieved in SrAl{sub 2}O{sub 4}:0.01Eu{sup 2+}, xYb{sup 3+} (x=0, 1, 2, 5, 10, 20, 30 mol%) samples. The photoluminescence properties of samples in visible and NIR regions were measured to verify the energy transfer (ET) from Eu{sup 2+} to Yb{sup 3+}. The results demonstrated that Eu{sup 2+} was an efficient sensitizer for Yb{sup 3+} in the SrAl{sub 2}O{sub 4} host lattice. According to Gaussian fitting analysis and temperature-dependent luminescence experiments, the conclusion was drawn that the cooperative energy transfer (CET) process dominated the ET process and the influence of charge transfer state (CTS) of Yb{sup 3+} could be negligible. As a result, the high energy transfer efficiency (ETE) and quantum yield (QY) have been acquired, the maximum value approached 73.68% and 147.36%, respectively. Therefore, this down-conversion material has potential application in crystalline silicon solar cells to improve conversion efficiency. - Graphical abstract: Near infrared quantum cutting was achieved in Eu{sup 2+}–Yb{sup 3+} co-doped SrAl{sub 2}O{sub 4} samples. The cooperative energy transfer process dominated energy transfer process and high energy transfer efficiency was acquired. - Highlights: • The absorption spectrum of Eu{sup 2+} ion is strong in intensity and broad in bandwidth. • The spectra of Eu{sup 2+} in SrAl{sub 2}O{sub 4} lies in the strongest region of solar spectrum. • The cooperative energy transfer (CET) dominated the energy transfer process. • The domination of CET is confirmed by experimental analysis. • SrAl{sub 2}O{sub 4}:Eu{sup 2+},Yb{sup 3+} show high energy transfer efficiency and long lifetime.

  4. Thermal diffusion in nanostructured porous InP

    International Nuclear Information System (INIS)

    Srinivasan, R.; Ramachandran, K.

    2008-01-01

    Nanostructured porous InP samples were prepared by electrochemical anodic dissolution of InP for various current densities and etching periods. The samples were characterized by SEM and photoluminescence (PL) where a blue shift was observed in PL. Thermal properties studies by photoacoustic (PA) spectroscopy revealed one order decrease in thermal conductivity of porous InP compared to the bulk. Further it is shown that the thermal conductivity of porous InP decreases with decrease in size of the particles. (author)

  5. Role of monovalent alkali ions in the Yb{sup 3+} centers of CaF{sub 2} laser crystals

    Energy Technology Data Exchange (ETDEWEB)

    Hraiech, Sana [Physical Chemistry of Luminescent Materials (LPCML), University of Lyon, Claude Bernard/Lyon 1 University, UMR 5620 CNRS, La Doua, 69622 Villeurbanne (France); Jouini, Anis [Physical Chemistry of Luminescent Materials (LPCML), University of Lyon, Claude Bernard/Lyon 1 University, UMR 5620 CNRS, La Doua, 69622 Villeurbanne (France); IMRAM, Tohoku University, 2-1-1, Katahira, Sendai 980-8577 (Japan); Jin Kim, Kyoung [IMRAM, Tohoku University, 2-1-1, Katahira, Sendai 980-8577 (Japan); Guyot, Yannick [Physical Chemistry of Luminescent Materials (LPCML), University of Lyon, Claude Bernard/Lyon 1 University, UMR 5620 CNRS, La Doua, 69622 Villeurbanne (France); Yoshikawa, Akira [IMRAM, Tohoku University, 2-1-1, Katahira, Sendai 980-8577 (Japan); Boulon, Georges, E-mail: georges.boulon@pcml.univ-lyon1.f [Physical Chemistry of Luminescent Materials (LPCML), University of Lyon, Claude Bernard/Lyon 1 University, UMR 5620 CNRS, La Doua, 69622 Villeurbanne (France)

    2010-03-15

    Yb{sup 3+} and M{sup +} monovalent alkali ions (M{sup +} = Li{sup +}, Na{sup +}, K{sup +})-co-doped CaF{sub 2} cubic laser crystals were grown by the micro-pulling-down method ({mu}-PD) under CF{sub 4} atmosphere. Structural and spectroscopic characterizations of Yb{sup 3+} in substitution of Ca{sup 2+} (absorption, emission and decay curves) were carried out to study the effect of M{sup +} ions as charge compensators.

  6. Magnesium doping in InAlAs and InGaAs/Mg films lattice-matched to InP grown by MOVPE

    Energy Technology Data Exchange (ETDEWEB)

    Ezzedini, Maher, E-mail: maher.ezz7@gmail.com [Monastir University, Laboratoire de Micro-Optoélectroniques et Nanostructures (Tunisia); Sfaxi, Larbi, E-mail: sfaxi.larbi@yahoo.fr [Sousse University, High School of Sciences and Technology of Hammam Sousse (Tunisia); M’Ghaieth, Ridha, E-mail: ridha.mghaieth@fsm.rnu.tn [Monastir University, Laboratoire de Micro-Optoélectroniques et Nanostructures (Tunisia)

    2017-01-15

    Mg-doped InAlAs and InGaAs films were grown at 560 °C lattice matched to InP semi-insulting substrate by metalorganic vapor phase epitaxy (MOVPE) under various Cp{sub 2}Mg flow conditions. Hall effect, photoluminescence (PL), high-resolution X-ray diffraction (HR-XRD), and secondary ion mass (SIMS) were the tools used in this work. The crystalline quality and the n-p conversion of the InAlAs and InGaAs/Mg films are described and discussed in relation to the Cp{sub 2}Mg flow. Distinguishing triple emission peaks in PL spectra is observed and seems to be strongly dependent on the Cp{sub 2}Mg flow. SIMS is employed to analyze the elements in the epitaxial layers. The variation of indium and magnesium components indicates a decrease of magnesium incorporation during the growth of InAlAs layers leading to a contracted lattice. In addition, the magnesium incorporation in the InGaAs lattice during growth has been confirmed by SIMS.

  7. Molecular beam epitaxy of InP single junction and InP/In0.53Ga0.47As monolithically integrated tandem solar cells using solid phosphorous source material

    International Nuclear Information System (INIS)

    Delaney, A.; Chin, K.; Street, S.; Newman, F.; Aguilar, L.; Ignatiev, A.; Monier, C.; Velela, M.; Freundlich, A.

    1998-01-01

    This work reports the first InP solar cells, InP/In 0.53 Ga 0.47 As tandem solar cells and InP tunnel junctions to be grown using a solid phosphorous source cracker cell in a molecular beam epitaxy system. High p-type doping achieved with this system allowed for the development of InP tunnel junctions. These junctions which allow for improved current matching in subsequent monolithically integrated tandem devices also do not absorb photons which can be utilized in the InGaAs structure. Photocurrent spectral responses compared favorably to devices previously grown in a chemical beam epitaxy system. High resolution x-ray scans demonstrated good lattice matching between constituent parts of the tandem cell. AM0 efficiencies of both InP and InP/InGaAs tandem cells are reported

  8. Enhanced photovoltaic performance of dye-sensitized solar cells based on NaYF4:Yb(3+), Er(3+)-incorporated nanocrystalline TiO2 electrodes.

    Science.gov (United States)

    Zhu, Guang; Wang, Hongyan; Zhang, Quanxin; Zhang, Li

    2015-08-01

    Near infrared to visible up-conversion of light by rare earth ion-doped phosphors (NaYF4:Yb(3+), Er(3+)) that convert multiple photons of lower energy to higher energy photons offer new possibilities for improved performance of photovoltaic devices. Here, up-conversion phosphor NaYF4:Yb(3+), Er(3+) doped nanocrystalline TiO2 films are designed and used as a electrode for dye-sensitized solar cells, and the photovoltaic performance of DSSCs based on composite electrodes are investigated. The results show the cell with NaYF4:Yb(3+), Er(3+) achieves a power conversion efficiency of 7.65% under one sun illumination (AM 1.5G, 100mWcm(-2)), which is an increase of 14% compared to the cell without NaYF4:Yb(3+), Er(3+) (6.71%). The performance improvement is attributed to the dual effects of enhanced light harvesting from extended light absorption range and increased light scattering, and lower electron transfer resistance. Copyright © 2015 Elsevier Inc. All rights reserved.

  9. Template-free synthesis and luminescent properties of hollow Ln:YOF (Ln = Eu or Er + Yb) microspheres

    Energy Technology Data Exchange (ETDEWEB)

    Martinez-Castro, E. [Instituto de Ciencia de Materiales de Sevilla (CSIC-US), Americo Vespucio 49, Isla de La Cartuja, 41092 Sevilla (Spain); García-Sevillano, J.; Cussó, F. [Dpto. Física de Materiales, C-04, Universidad Autónoma de Madrid, Avda. Francisco Tomás y Valiente, 7, 28049 Madrid (Spain); Ocaña, M., E-mail: mjurado@icmse.csic.es [Instituto de Ciencia de Materiales de Sevilla (CSIC-US), Americo Vespucio 49, Isla de La Cartuja, 41092 Sevilla (Spain)

    2015-01-15

    Highlights: • Hollow lanthanide doped YOF spheres have been synthesised through a template-free procedure. • Strong red emissions are observed for Eu-doped spheres under UV illumination. • Concentration quenching of luminescence takes place in the spheres at very high Eu doping levels. • Bright red emission is observed for Er, Yb codoped spheres, making this matrix advantageous for biomedical imaging. - Abstract: A method for the synthesis of hollow lanthanide doped yttrium oxyfluoride (YOF) spheres in the micrometer size range with cubic structure based on the pyrolysis at 600 °C of liquid aerosols generated from aqueous solutions containing the corresponding rare earth chlorides and trifluoroacetic acid has been developed. This procedure, which has been used for the first time for the synthesis of YFO based materials, is simpler and advantageous when compared with other methods usually employed for the production of hollow spheres since it does not require the use of sacrificial templates. In addition, it is continuous, which is desirable because of practical reasons. The procedure is also suitable for doping the YOF spheres with europium cations resulting in down converting red phosphors when activated with UV light, or for co-doping with both Er{sup 3+} and Yb{sup 3+} giving rise to up-converting phosphors, which emit intense red light under near infrared (NIR) irradiation. Because of their optical properties and hollow architecture, the developed materials may find applications in optoelectronic devices and biotechnology.

  10. XAFS studies of ytterbium doped lead-telluride

    International Nuclear Information System (INIS)

    Radisavljevic, I.; Novakovic, N.; Romcevic, N.; Manasijevic, M.; Mahnke, H.-E.; Ivanovic, N.

    2010-01-01

    X-ray Absorption Fine Structure (XAFS) measurements were performed on uniformly doped PbTe:Yb (1.3 at.%) at all elemental absorption edges and the analysis of the results has provided precise information on the local structure around each atom. From the near edge part of the absorption spectra it was determined that Yb is in the mixed valent state, which is predominantly divalent with a small trivalent contribution. The analysis of the high energy region of the absorption spectra revealed that Yb incorporation causes deformation of the host PbTe lattice, manifested through extension of all the nearest-, and next-nearest neighbour distances.

  11. Effect of doped ceria interlayer on cathode performance of the electrochemical cell using proton conducting oxide

    International Nuclear Information System (INIS)

    Sakai, Takaaki; Matsushita, Shotaro; Hyodo, Junji; Okuyama, Yuji; Matsuka, Maki; Ishihara, Tatsumi; Matsumoto, Hiroshige

    2012-01-01

    Highlights: ► Ce 0.8 Yb 0.2 O 2−δ (YbDC) interlayer conducted a large amount of protons. ► YbDC can work as cathode interlayer for proton conducting electrolyte cells. ► Cathode overpotential of the YbDC interlayer cells showed a plateau at about 400 mV. - Abstract: Introduction of doped ceria interlayer to cathode/electrolyte interface of the electrochemical cell with proton conducting electrolyte was investigated using thin Ce 0.8 Yb 0.2 O 2−δ (YbDC) interlayer of about 500 nm thickness. YbDC interlayer conducted a large amount of protons as much as 170 mA cm −2 . It was also found that cathode overpotential of the YbDC interlayer cells consistently showed a plateau at about 400 mV, at which that of the non-interlayer cells did not show, suggesting a possibility that cathode reaction is changed by introducing the doped ceria interlayer. This result also indicates that the interlayer showed high activity for cathode reaction when enough cathodic bias was applied. Especially, the interlayer showed high activity for the improvement of poor cathode reaction between SrZr 0.9 Y 0.1 O 3−α (SZY-91) electrolyte and platinum cathode.

  12. Research of the mode instability threshold in high power double cladding Yb-doped fiber amplifiers

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Yanshan; Ma, Yi; Sun, Yinhong; Peng, Wanjing; Tang, Chun [Institute of Applied Electronics, CAEP, Mianyang, Sichuan (China); The Key Laboratory of Science and Technology on High Energy Laser, CAEP, Mianyang, Sichuan (China); Liu, Qinyong; Ke, Weiwei [Institute of Applied Physics and Computational Mathematics, CAEP, Beijing (China); Wang, Xiaojun [Institute of Applied Physics and Computational Mathematics, CAEP, Beijing (China); Technical Institute of Physics and Chemistry, CAS, Beijing (China)

    2017-08-15

    We experimentally investigate the behavior of the mode instability (MI) threshold in the double cladding Yb-doped fiber amplifier when the amplifier is pumped by broad linewidth laser diodes and narrow linewidth laser diodes respectively. It is found that the MI threshold increases by 26% when the amplifier is pumped by the broad linewidth laser diodes. Experiment results show that the MI threshold is affected by the local heat load rather than the average or the total heat load. The calculation shows that the local heat deposit actually plays the key role to stimulate the MI behaviour. At the MI threshold position in the fiber, the local heat deposit also changes dramatically. The effect of the thermal conductivity on the MI threshold is also studied. Our investigation shows that the MI threshold increases from 1269 W to 1950 W when the thermal conductivity of the fiber amplifier is increased from 0.3 W/(m . K) to 5 W/(m . K). Through optimizing the pump linewidth and the cooling efficiency of the gain fiber, the MI threshold is doubled in our experiment. (copyright 2017 by WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  13. Research of the mode instability threshold in high power double cladding Yb-doped fiber amplifiers

    International Nuclear Information System (INIS)

    Wang, Yanshan; Ma, Yi; Sun, Yinhong; Peng, Wanjing; Tang, Chun; Liu, Qinyong; Ke, Weiwei; Wang, Xiaojun

    2017-01-01

    We experimentally investigate the behavior of the mode instability (MI) threshold in the double cladding Yb-doped fiber amplifier when the amplifier is pumped by broad linewidth laser diodes and narrow linewidth laser diodes respectively. It is found that the MI threshold increases by 26% when the amplifier is pumped by the broad linewidth laser diodes. Experiment results show that the MI threshold is affected by the local heat load rather than the average or the total heat load. The calculation shows that the local heat deposit actually plays the key role to stimulate the MI behaviour. At the MI threshold position in the fiber, the local heat deposit also changes dramatically. The effect of the thermal conductivity on the MI threshold is also studied. Our investigation shows that the MI threshold increases from 1269 W to 1950 W when the thermal conductivity of the fiber amplifier is increased from 0.3 W/(m . K) to 5 W/(m . K). Through optimizing the pump linewidth and the cooling efficiency of the gain fiber, the MI threshold is doubled in our experiment. (copyright 2017 by WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  14. Local structure investigation of Ga and Yb dopants in Co4Sb12 skutterudites

    Science.gov (United States)

    Hu, Yanyun; Chen, Ning; Clancy, J. P.; Salvador, James R.; Kim, Chang-Yong; Shi, Xiaoya; Li, Qiang; Kim, Young-June

    2017-12-01

    We report comprehensive x-ray absorption spectroscopy studies at both the Ga K edge and Yb L2 edge to elucidate the local structure of Ga and Yb dopants in YbxGayCo4Sb12 . Our extended x-ray absorption fine structure (EXAFS) data confirm that Ga atoms occupy two crystallographic sites: one is the 24 g site replacing Sb, and the other is the 2 a site in the off-center void position. We find that the occupancy ratio of these two sites varies significantly as a function of the filling fraction of additional Yb, which exclusively occupies the 2 a on-center site. At low concentrations of Yb, Ga24 g and Ga2 a dopants coexist and they form a charge-compensated compound defect proposed by Qiu et al. [Adv. Funct. Mater. 23, 3194 (2013), 10.1002/adfm.201202571]. The Ga24 g occupancy increases gradually with increasing Yb concentration, and almost all Ga occupies the 24 g site for the highest Yb concentration studied (x =0.4 ). In addition to the local structural evidence provided by our EXAFS data, we also present x-ray absorption near-edge structure (XANES) spectra, which show a small Ga K -edge energy shift as a function of Yb concentration consistent with the change from predominantly Ga2 a to Ga24 g states. Our result suggests that the increased solubility of Yb in Yb-Ga co-doped Co4Sb12 skutterudites is due to the increased Ga24 g electron acceptor, and thus provides an important strategy to optimize the carrier concentration in partially filled skutterudites.

  15. Studies on semiconductors based on InP with sub-ps response times; Untersuchungen an auf InP basierenden Halbleitern mit sub-ps Responsezeiten

    Energy Technology Data Exchange (ETDEWEB)

    Biermann, K.

    2007-06-28

    The present work describes investigation of new material concepts accomplished using molecular-beam-epitaxy (MBE) growth for application in ultra-fast photonic components. Nominally undoped and Be doped GaInAs/AlInAs multiple-quantumwell structures (MQW) were grown by MBE at growth temperatures down to 100 C (LT-MBE) on semi-insulating InP substrates. Crystalline, electric and optical properties of as-grown and annealed structures were investigated. Energy states near the conduction band of GaInAs determine the electrical and optical properties of LT-MQWs. The dynamics of charge carrier relaxation was studied by means of pump and probe experiments. Measurements of the differential transmission when excited by an additional cw laser and measurements utilizing two closely sequenced pump pulses support the capability of Be doped as-grown (annealed) LT GaInAs/AlInAs MQW structures for use in optical switches at switching frequencies in the 1 Tbit/s (250 Gbit/s) range. The voltage-induced change of interband transmission of InP based quantumcascade-lasers (QCL) during pulsed mode operation was analyzed by means of 8 band k.p calculations. The impacts of varying charge carrier distributions and of electrically heated samples can be neglected compared to the dominating effect of the electrical field on the interband transmission. The impact of MBE growth parameters on the interface quality of AlAsSb/ GaInAs heterostructures were determined by means of Hall measurements, temperature- and intensity-dependent PL measurements and spectral measurements of the interband- and intersubband-absorption. The impact of In segregation and Sb diffusion on the intersubband absorption was analyzed on the basis of bandstructure calculations. Intersubband transitions at wavelengths of about 1.8 {mu}m (1.55 {mu}m) were successfully achieved in MQW (coupled QW) structures. (orig.)

  16. Optical and structural characterization of rare earth doped niobium phosphate glasses

    International Nuclear Information System (INIS)

    Sene, F.F.; Martinelli, J.R.; Gomes, L.

    2004-01-01

    Phosphate glasses containing up to 45mol% of niobium were obtained. X-ray diffraction, infrared, Raman, and optical absorption spectroscopy were used to analyze those materials. The refractive index varies from 1.70 to 1.85 as the amount of Nb increases. Niobium phosphate glasses with optical transparence in the (400-2500nm) range were produced. The cut off varied from 342nm to 378nm as a function of the Nb concentration. The cut off is due to the charge transfer O 2 ->Nb 5+ . Glasses containing 10mol% of Nb 2 O 5 are the most promising materials to be used as rare-earth ions hosts because they are chemically resistant, and show optical transparency in the spectral range of visible to infrared. Doping the glasses with 1-5mol% of Er, Ho, Pr, and Yb ions does not change the glass structure, as measured by X-ray diffraction, infrared, and Raman spectroscopy. The fluorescence lifetimes were determined for Nd, Yb, and Er, and the absorption cross-section were determined for all ions. The energy transfer in co-doped Yb-Er system was measured, and the lifetime of excited states and the luminescence efficiency were determined to be 91% for the Er 4 I 11/2 level, in the Yb-Er co-doped glasses

  17. Direct Comparison of Yb.sup.3+./sup.:CaF.sub.2./sub. and heavily doped Yb.sup.3+./sup.:YLF as laser media at room temperature

    Czech Academy of Sciences Publication Activity Database

    Pirri, A.; Alderighi, D.; Toci, G.; Vannini, M.; Nikl, Martin; Sato, H.

    2009-01-01

    Roč. 17, č. 20 (2009), s. 18312-18319 ISSN 1094-4087 Grant - others:AV ČR(CZ) M100100910 Institutional research plan: CEZ:AV0Z10100521 Keywords : Yb 3+ :YLF * Yb 3+ :CaF 2 * solid state laser * diode pumped Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 3.278, year: 2009

  18. Yb valence state in Yb{sub 5}Rh{sub 4}Ge{sub 10}

    Energy Technology Data Exchange (ETDEWEB)

    Sato, Hitoshi; Arita, Masashi; Shimada, Kenya; Namatame, Hirofumi; Taniguchi, Masaki [Hiroshima Synchrotron Radiation Center, Hiroshima University, Higashi-Hiroshima (Japan); Utsumi, Yuki [Synchrotron SOLEIL, L' Orme des Merisiers, Gif-sur-Yvette (France); Katoh, Kenichi [Department of Applied Physics, National Defense Academy, Yokosuka (Japan); Mimura, Kojiro [Graduate School of Engineering, Osaka Prefecture University, Sakai (Japan); Ueda, Shigenori [Synchrotron X-ray Station at SPring-8, National Institute for Materials Science, Hyogo (Japan); Quantum Beam Unit, National Institute for Materials Science, Tsukuba (Japan); Yamaoka, Hitoshi [RIKEN SPring-8 Center, Hyogo (Japan); Rousuli, Awabaikeli [Graduate School of Science, Hiroshima University, Higashi-Hiroshima (Japan); Umeo, Kazunori [NBARD, Hiroshima University, Higashi-Hiroshima (Japan)

    2017-06-15

    Temperature- and pressure-dependent Yb valence state in Yb{sub 5}Rh{sub 4}Ge{sub 10} has been investigated by means of Yb 3d hard X-ray photoemission spectroscopy (HAXPES) and Yb L{sub 3} absorption spectroscopy (XAS). The mean Yb valence derived from the Yb 3d HAXPES is estimated to be ∝2.78 at 300 K and decreases to ∝2.74 at 20 K. On the other hand, the Yb valence deduced from the Yb L{sub 3} XAS at 300 K is almost constant with ∝2.81 in the pressure range between 9.2 and 34.7 GPa. (copyright 2017 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  19. Near-infrared photoluminescence in La{sub 0.98}AlO{sub 3}: {sub 0.02}Ln{sup 3+}(Ln = Nd/Yb) for sensitization of c-Si solar cells

    Energy Technology Data Exchange (ETDEWEB)

    Sawala, N. S., E-mail: nssawala@gmail.com; Koparkar, K. A.; Omanwar, S. K. [Department of Physics, SantGadge Baba Amravati University, Amravati - MH, 444602 (India); Bajaj, N. S. [Department of Physics, Toshniwal Art, Commerce and Science College, Sengoan, Hingoli - MH (India)

    2016-05-06

    The host matrix LaAlO{sub 3} was synthesized by conventional solid state reaction method in which the Nd{sup 3+} ions and Yb{sup 3+} ions successfully doped at 2mol% concentrations. The phase purity was confirmed by X ray powder diffraction (XRD) method. The photoluminescence (PL) properties were studied by spectrophotometer in near infra red (NIR) and ultra violet visible (UV-VIS) region. The Nd{sup 3+} ion doped LaAlO{sub 3} converts a visible (VIS) green photon (587 nm) into near infrared (NIR) photon (1070 nm) while Yb{sup 3+} ion doped converts ultra violet (UV) photon (221 nm) into NIR photon (980 nm). The La{sub 0.98}AlO{sub 3}: {sub 0.02}Ln{sup 3+}(Ln = Nd / Yb) can be potentiality used for betterment of photovoltaic (PV) technology. This result further indicates its potential application as a luminescence converter layer for enhancing solar cells performance.

  20. Measurement of surface recombination velocity on heavily doped indium phosphide

    International Nuclear Information System (INIS)

    Jenkins, P.; Ghalla-Goradia, M.; Faur, M.; Bailey, S.

    1990-01-01

    The controversy surrounding the published low values of surface recombination velocity (SRV) in n-InP, solidified in recent years when modeling of existing n/p InP solar cells revealed that the front surface SRV had to be higher than 1 x 10 6 cm/sec in order to justify the poor blue response that is characteristic of all n/p InP solar cells. In this paper, SRV on heavily doped (>10 18 cm -3 )n-type and p-type InP is measured as a function of surface treatment. For the limited range of substrates and surface treatments studied, SRV and surface stability depend strongly on the surface treatment. SRVs of ∼10 5 cm/sec in both p-type and n-type InP are obtainable, but in n-type the low SRV surfaces were unstable, and the only stable surfaces on n-type had SRVs of >10 6 cm/sec

  1. Thermal Properties of Transparent Yb-Doped YAG Ceramics at Elevated Temperatures

    Czech Academy of Sciences Publication Activity Database

    Hostaša, J.; Matějíček, Jiří; Nait-Ali, B.; Smith, D.S.; Pabst, W.; Esposito, L.

    2014-01-01

    Roč. 97, č. 8 (2014), s. 2602-2606 ISSN 0002-7820 Institutional support: RVO:61389021 Keywords : yttrium aluminium garnet * Yb:YAG * thermal diffusivity Subject RIV: JH - Ceramics, Fire-Resistant Materials and Glass Impact factor: 2.610, year: 2014 http://onlinelibrary.wiley.com/doi/10.1111/jace.13015/abstract

  2. High efficiency laser action in mildly doped Yb:LuYAG ceramics

    Czech Academy of Sciences Publication Activity Database

    Pirri, A.; Toci, G.; Li, J.; Xie, T.; Pan, Y.; Babin, Vladimir; Beitlerová, Alena; Nikl, Martin; Vannini, M.

    2017-01-01

    Roč. 73, Nov (2017), s. 312-318 ISSN 0925-3467 Institutional support: RVO:68378271 Keywords : laser ceramic s * Yb laser * mixed garnets * LuYAG Subject RIV: BM - Solid Matter Physics ; Magnetism OBOR OECD: Condensed matter physics (including formerly solid state physics, supercond.) Impact factor: 2.238, year: 2016

  3. Synthesis and photocatalytic activity of ytterbium-doped titania/diatomite composite photocatalysts

    Science.gov (United States)

    Tang, Wenjian; Qiu, Kehui; Zhang, Peicong; Yuan, Xiqiang

    2016-01-01

    Ytterbium-doped titanium dioxide (Yb-TiO2)/diatomite composite materials with different Yb concentrations were prepared by sol-gel method. The phase structure, morphology, and chemical composition of the as-prepared composites were well characterized by X-ray diffraction (XRD), Fourier transform infrared spectroscopy, Raman spectroscopy, scanning electron microscopy (SEM), and ultraviolet-visible (UV-vis) diffuse reflection spectroscopy. The XRD and Raman spectroscopy analysis indicated that the TiO2 existed in the form of pure anatase in the composites. The SEM images exhibited the well deposition and dispersion of TiO2 nanoparticles with little agglomeration on the surfaces of diatoms. The UV-vis diffuse reflection spectra showed that the band gap of TiO2 could be narrowed by the introduction of Yb species, which was further affected by doping concentration of Yb. The photocatalytic activity of synthesized samples was investigated by the degradation of methylene blue (MB) under UV light irradiation. It was observed that the photocatalytic degradation followed a pseudo-first-order kinetics according to the Langmuir-Hinshelwood model. Compared to TiO2 and TiO2/diatomite, the Yb-TiO2/diatomite composites exhibited higher photocatalytic activity toward degradation of MB using UV light irradiation.

  4. Spin re-orientation in heavy fermion system α - YbAl1 - x FexB4

    Science.gov (United States)

    Wu, Shan; Broholm, C.; Kuga, K.; Suzuki, Shintaro; Nakatsuji, S.; Mourigal, M.; Stone, M.; Tian, Wei; Qiu, Y.; Rodriguez-Rivera, Jose

    Non centro-symmetric α - YbAlB4 has a heavy Fermi liquid ground state and shares many characteristics with centro-symmetric β - YbAlB4 . Both isomorphs display intermediate valence, associated with a fluctuation scale of T0 = 200 K and a Kondo lattice scale of T* = 8 K. Unlike β - YbAlB4 , α - YbAlB4 is at the boundary of a transition from a Fermi liquid metallic state to an antiferromagnetic (AFM) insulating state, driven by Fe substitution of Al. Magnetization and specific heat measurements reveal two different antiferromagnetic phases with TN = 9 K and TN = 2 K for Fe concentration above and below x =0.07. We report single crystal neutron scattering experiments on Fe doped YbAlB4 with x =0.035 and x =0.125. While the ordering wave vector is identical, k -> = (1 , 0 , 0) , the spin orientation switches from c to a with increasing Fe concentration. This suggests different anisotropic hybridization between 4f and conduction electrons that we confirmed by determining the crystal field levels. Supported by DOE, BES through DE-FG02-08ER46544.

  5. Structural properties of lithium borate glasses doped with rare earth ions

    Directory of Open Access Journals (Sweden)

    Thomazini D.

    2001-01-01

    Full Text Available This paper presents the study on lithium triborate glass (LBO in the system (1-x|3B2O3.Li2O| (xNb2O5 yPr3+ zYb3+ wNd3+ with 0 <= x <= 20 mol% (y, z and w in mol%. The samples were studied by Raman spectroscopy, infrared absorption and differential thermal analysis. Pr3+-doped LBO and Pr3+/Yb3+-doped LBO samples show an increase of the glass transition and crystallization temperatures and a decrease of the fusion temperature associated with the increase of the praseodymium concentration in the LBO matrix. For the Nd3+-doped LBO and Pr3+/Yb3+-doped (LBO+Nb2O5 samples, a decrease of the glass transition temperature of the samples was observed. The increase of the rare earth doping leads to an increase of the difference between the glass transition and the crystallization temperatures. From infrared analysis it was possible to identify all the modes associated to the B-O structure. The NbO6 octahedra was also identified by IR spectroscopy for samples with x=5, 10, 15 and 20 mol% and y=0.05, z=1.1 mol%. Raman spectroscopy shows the presence of boroxol rings, tetrahedral and triangular coordination for boron. For samples containing niobium, the Raman spectra show the vibrational mode associated with the Nb-O bond in the niobium octahedra (NbO6.

  6. InP Solar Cells and their Flight Experiments

    OpenAIRE

    TAKAHASHI, Keiji; YAMAGUCHI, Masafumi; TAKAMOTO, Tatsuya; IKEGAMI, Shingo; OHNISHI, Akira; HAYASHI, Tomonao; USHIROKAWA, Akio; KOHBATA, Masahiko; ARAI, Hidetoshi; HASHIMOTO, Katsumasa; ORH, Takeshi; OKAZAKI, Hitoshi; TAKAMURA, Hideto; URA, Mitsuru; OHMORI, Masamichi

    1992-01-01

    We have developed high-efficiency homojunction 1 cm × 2 cm InP space solar cells by diffusing In_2S_3 into p type InP substrates and investigated their fundamental characteristics such as electrical and mechnical characteristics and thermal properties. On the radiation resistant mechanism of InP cells, we have studied InP cells fabricated at NTT Laboratories and found superior properties such as room temperture annealing and minority carrier injection enhanced annealing phenomena for radiatio...

  7. High slope efficiency and high refractive index change in direct-written Yb-doped waveguide lasers with depressed claddings.

    Science.gov (United States)

    Palmer, Guido; Gross, Simon; Fuerbach, Alexander; Lancaster, David G; Withford, Michael J

    2013-07-15

    We report the first Yb:ZBLAN and Yb:IOG10 waveguide lasers fabricated by the fs-laser direct-writing technique. Pulses from a Titanium-Sapphire laser oscillator with 5.1 MHz repetition rate were utilized to generate negative refractive index modifications in both glasses. Multiple modifications were aligned in a depressed cladding geometry to create a waveguide. For Yb:ZBLAN we demonstrate high laser slope efficiency of 84% with a maximum output power of 170 mW. By using Yb:IOG10 a laser performance of 25% slope efficiency and 72 mW output power was achieved and we measured a remarkably high refractive index change exceeding Δn = 2.3 × 10(-2).

  8. Optical spectroscopy of rare-earth ions doped KY(WO4)2 thin films

    NARCIS (Netherlands)

    García-Revilla, S.; Valiente, R.; Romanyuk, Y.E.; Utke, I.; Pollnau, Markus

    KY(WO4)2 thin films doped with Dy3+, Tb3+, Yb3+, were grown onto KY(WO4)2 substrates using liquid-phase epitaxy. Spectroscopic investigations of the grown layers were performed. Obtained results were compared with spectra given for bulk crystals. Upconversion experiments after direct Yb3+ excitation

  9. Alloying of Yb-Cu and Yb-Ag utilizing liquid ammonia metal solutions of ytterbium

    International Nuclear Information System (INIS)

    Imamura, H.; Yoshimura, T.; Sakata, Y.

    2003-01-01

    In the course of the studies on preparation of novel compounds using the dissolution of Eu or Yb metals in liquid ammonia, the formation of Yb-Cu and Yb-Ag intermetallic films has been found. When Cu or Ag metal powders were placed in a reactor containing a solution of Yb metal in liquid ammonia, the dissolved Yb readily react with the Cu or Ag metal particles to form surface alloy compounds. X-ray diffraction of Yb-Cu showed that upon thermal treatment above 673 K, the Yb metal deposited on the Cu particles reacted together to be transformed into the YbCu 6.5 intermetallic compound. A characteristic endothermic peak at 749 K, due to alloying of Yb-Cu, was observed by the differential scanning calorimeter measurements. By use of the high reactivity of liquid ammonia metal solutions of ytterbium, it was found that the ytterbium intermetallic films were readily formed under mild conditions. Yb-Cu and Yb-Ag exhibited enhanced catalytic activity for the hydrogenation of ethene as a result of alloying

  10. High resistivity in InP by helium bombardment

    International Nuclear Information System (INIS)

    Focht, M.W.; Macrander, A.T.; Schwartz, B.; Feldman, L.C.

    1984-01-01

    Helium implants over a fluence range from 10 11 to 10 16 ions/cm 2 , reproducibly form high resistivity regions in both p- and n-type InP. Average resistivities of greater than 10 9 Ω cm for p-type InP and of 10 3 Ω cm for n-type InP are reported. Results are presented of a Monte Carlo simulation of helium bombardment into the compound target InP that yields the mean projected range and the range straggling

  11. Enhancement of single particle rare earth doped NaYF4: Yb, Er emission with a gold shell

    International Nuclear Information System (INIS)

    Li, Ling; Green, Kory; Hallen, Hans; Lim, Shuang Fang

    2015-01-01

    Upconversion of infrared light to visible light has important implications for bioimaging. However, the small absorption cross-section of rare earth dopants has limited the efficiency of these anti-Stokes nanomaterials. We present enhanced excitation absorption and single particle fluorescent emission of sodium yttrium fluoride, NaYF 4 : Yb, Er based upconverting nanoparticles coated with a gold nanoshell through surface plasmon resonance. The single gold-shell coated nanoparticles show enhanced absorption in the near infrared, enhanced total emission intensity, and increased green relative to red emission. We also show differences in enhancement between single and aggregated gold shell nanoparticles. The surface plasmon resonance of the gold-shell coated nanoparticle is shown to be dependent on the shell thickness. In contrast to other reported results, our single particle experimental observations are corroborated by finite element calculations that show where the green/red emission enhancement occurs, and what portion of the enhancement is due to electromagnetic effects. We find that the excitation enhancement and green/red emission ratio enhancement occurs at the corners and edges of the doped emissive core. (paper)

  12. Enhancement of the up-conversion luminescence from NaYF{sub 4}:Yb{sup 3+},Tb{sup 3+}

    Energy Technology Data Exchange (ETDEWEB)

    Hölsä, Jorma, E-mail: jholsa@utu.fi [University of Turku, Department of Chemistry, FI-20014 Turku (Finland); Turku University Centre for Materials and Surfaces (MatSurf), Turku (Finland); Universidade de São Paulo, Instituto de Química, São Paulo-SP (Brazil); Laihinen, Tero [University of Turku, Department of Chemistry, FI-20014 Turku (Finland); Laamanen, Taneli; Lastusaari, Mika [University of Turku, Department of Chemistry, FI-20014 Turku (Finland); Turku University Centre for Materials and Surfaces (MatSurf), Turku (Finland); Pihlgren, Laura [University of Turku, Department of Chemistry, FI-20014 Turku (Finland); Graduate School of Materials Research (GSMR), Turku (Finland); Rodrigues, Lucas C.V. [University of Turku, Department of Chemistry, FI-20014 Turku (Finland); Universidade de São Paulo, Instituto de Química, São Paulo-SP (Brazil); Soukka, Tero [University of Turku, Department of Biochemistry, FI-20014 Turku (Finland)

    2014-04-15

    The synthesis conditions of the Yb{sup 3+} and Tb{sup 3+} co-doped NaYF{sub 4} were optimized by reducing the number of washings to include only ethanol. The avoidance of the loss of amorphous NaF prior to post-annealing of the as-prepared materials resulted in the enhancement of the otherwise rather weak up-conversion from Tb{sup 3+} by 1–2 orders of magnitude. At the same time, the temperature of formation of the hexagonal NaRF{sub 4} phase with high up-conversion could be lowered by 100 °C down to 350 °C. This improvement in up-conversion was concluded to result from the better stoichiometry of the material without washing with water. The deficit of Na{sup +} would result in the excess of fluoride which, although not as fatal to the luminescence as the fluoride vacancies, has serious implications to the up-conversion intensity. A further enhancement in the up-conversion luminescence was observed to be due to the Er{sup 3+} ion impurity frequently associated with high-concentration Yb{sup 3+} materials. The mechanism involving the unintentional Er{sup 3+} sensitizer and the resonance energy transfer in the Yb{sup 3+}–Er{sup 3+}–Tb{sup 3+} co-doped NaYF{sub 4} were discussed based on the energy level schemes of the Yb{sup 3+}, Er{sup 3+}, and Tb{sup 3+} ions in NaYF{sub 4}.

  13. Optical properties of ytterbium-doped yttrium oxide ceramics

    Energy Technology Data Exchange (ETDEWEB)

    Solomonov, V.I.; Maksimov, R.N. [Institute of Electrophysics UrB RAS, Amundsena 106, 620016 Ekaterinburg (Russian Federation); Ural Federal University Named After the First President of Russia B.N. Yeltsin, Mira 19, 620002 Ekaterinburg (Russian Federation); Osipov, V.V.; Shitov, V.A.; Lipchak, A.I. [Institute of Electrophysics UrB RAS, Amundsena 106, 620016 Ekaterinburg (Russian Federation)

    2017-05-15

    Ytterbium-doped yttrium oxide (Yb:Y{sub 2}O{sub 3}) transparent ceramics with different sintering additives (Lu{sub 2}O{sub 3}, Sc{sub 2}O{sub 3}, CeO{sub 2}, ZrO{sub 2}, or HfO{sub 2}) were fabricated using nanopowders produced by laser ablation. Transmission and photoluminescence spectra of the obtained ceramics were investigated at room temperature. Highest in-line transmittance was over 80% at the wavelength of 1060 nm for 2 mm thick Yb:Y{sub 2}O{sub 3} ceramics with zirconium and hafnium. Divalent Yb ions with the ground state electron configuration 4f{sup 13}6s were revealed. The absorption and emission bands caused by s <-> s transitions of these ions were observed in the IR spectral range of Yb{sup 3+} ions. The superposition of both Yb{sup 3+} and Yb{sup 2+} emission bands leads to an effective broadening of the whole luminescence band. (copyright 2016 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  14. Effect of Sintering Temperature on Microstructure, Chemical Stability and Electrical Properties of Transition Metal or Yb-Doped BaZr0.1Ce0.7Y0.1M0.1O3-δ (M = Fe, Ni, Co and Yb

    Directory of Open Access Journals (Sweden)

    Behzad eMirfakhraei

    2014-03-01

    Full Text Available Perovskite-type BaZr0.1Ce0.7Y0.1M0.1O3-δ (M = Fe, Ni, Co and Yb (BZCY-M oxides were synthesized using the conventional solid-state reaction method at 1350-1550 oC in air in order to investigate the effect of dopants on sintering, crystal structure, chemical stability under CO2 and H2S, and electrical transport properties. The formation of the single-phase perovskite-type structure with an orthorhombic space group Imam was confirmed by Rietveld refinement using powder X-ray diffraction (PXRD for the Fe, Co, Ni and Yb-doped samples. The BZCY-Co and BZCY-Ni oxides show a total electrical conductivity of 0.01 and 8 × 10-3 Scm-1 at 600 oC in wet H2 with an activation energy of 0.36 and 0.41 eV, respectively. Scanning electron microscopy (SEM and energy-dispersive X-ray analysis (EDX revealed Ba and Co rich secondary phase at the grain-boundaries, which may explain the enhancement in the total conductivity of the BZCY-Co. However, ex-solution of Ni at higher sintering temperatures, especially at 1550 oC, decreases the total conductivity of the BZCY-Ni material. The Co and Ni dopants act as a sintering aid and form dense pellets at a lower sintering temperature of 1250 oC. The Fe, Co and Ni-doped BZCY-M samples synthesized at 1350 oC show stability in 30 ppm H2S/H2 at 800 oC, and increasing the firing temperature to 1550 oC, enhanced the chemical stability in CO2 / N2 (1: 2 at 25-900 oC. The BZCY-Co and Ni compounds with high conductivity in wet H2 could be considered as possible anodes for intermediate temperature solid oxide fuel cells (IT-SOFCs.

  15. Efficient room temperature cw Yb:glass laser pumped by a 946nm Nd:YAG laser

    OpenAIRE

    Koch, R.; Clarkson, W.A.; Hanna, D.C.; Jiang, S.; Myers, M.J.; Rhonehouse, D.; Hamlin, S.J.; Griebner, U.; Schönnagel, H.

    1997-01-01

    By pumping with a cw diode-pumped Nd:YAG laser operating at 946nm laser operation of a new Yb-doped phosphate glass with 440mW cw output power and a slope efficiency of 48% with respect to the absorbed pump power was achieved at room temperature

  16. Upconversion luminescence properties of Y2O3:Yb3+, Er3+ nanostructures

    International Nuclear Information System (INIS)

    De Gejihu; Qin Weiping; Zhang Jishen; Zhang Jishuang; Wang, Yan; Cao Chunyan; Cui Yang

    2006-01-01

    Cubic Y 2 O 3 nanostructures doped with Yb 3+ and Er 3+ ions were synthesized by a facile hydrothermal method. Three distinct shapes such as nanotubes, nanospheres and nanoflakes formed in the products by adjusting the pH value of reacting solution. Powder X-ray diffraction analyses indicate that all the three nanostructures are pure cubic phase, while electron microscopy measurements confirm the formation of different morphologies. These nanostructures exhibit strong visible upconversion luminescence under the excitation of a 978-nm diode laser. In Yb 3+ - and Er 3+ - codoped Y 2 O 3 nanocrystals, the relative intensity of green emission became stronger as the size and morphology of sample changed from tubes to flakes

  17. Crystal growth and spectroscopic characterization of Yb3+:LiTaO3

    International Nuclear Information System (INIS)

    Gruber, John B.; Allik, Toomas H.; Sardar, Dhiraj K.; Yow, Raylon M.; Scripsick, Michael; Wechsler, Barry

    2006-01-01

    Spectroscopic properties are presented for Yb 3+ incorporated into single crystals of LiTaO 3 grown by the top-seeded solution growth method. From an analysis of the absorption and fluorescence spectra, we are able to determine the Stark-level components of the 2 F 7/2 (the ground-state multiplet manifold) and the 2 F 5/2 (the excited-state multiplet manifold of Yb 3+ (4f 13 )). The room-temperature fluorescence lifetime of 2 F 5/2 is 678μs as measured on a thin sample to reduce possibilities for reabsorption. Spectral comparisons of Yb 3+ -doped LiTaO 3 and LiNbO 3 are drawn. The crystal-field splitting of Yb 3+ (4f 13 ) in both crystal hosts is modeled using a set of crystal-field splitting parameters, B nm , determined from a recent spectroscopic analysis of Er 3+ (4f 11 ) in LiNbO 3 . Without adjustment of the B nm parameters, the model predicts the Stark-level energy and the symmetry label for each level in reasonable agreement with the experimental values. Less photorefractive than its niobate cousin, LiTaO 3 has potential for use in numerous integrated electro-optical circuits and devices

  18. Yb3+:Sr3Y2(BO3)4: A potential ultrashort pulse laser crystal

    International Nuclear Information System (INIS)

    Sun, Shijia; Xu, Jinlong; Wei, Qi; Lou, Fei; Huang, Yisheng; Yuan, Feifei; Zhang, Lizhen; Lin, Zhoubin; He, Jingliang; Wang, Guofu

    2015-01-01

    Highlights: • A Yb 3+ :Sr 3 Y 2 (BO 3 ) 4 crystal was grown successfully by Czochralski method. • The crystal has wide absorption and emission bandwidth. • 3.47 W continuous wave laser output with a slope efficiency of 29% was obtained. • The results show that the crystal is a promising ultrashort pulse laser material. - Abstract: A Yb 3+ :Sr 3 Y 2 (BO 3 ) 4 crystal was grown successfully by the Czochralski method. The polarized spectral properties and continuous wave laser output of this crystal were investigated in detail. The crystal has larger absorption and emission cross sections compared with many mature Yb 3+ -doped borate crystals. The full width at half maximum of the emission bands around 1023 nm are 69 nm (E//a), 61 nm (E//b) and 65 nm (E//c). 3.47 W continuous wave laser output with a slope efficiency of 29% and an optical conversion efficiency of 24% was obtained. The results reveal that Yb 3+ :Sr 3 Y 2 (BO 3 ) 4 crystal is an excellent candidate for ultrashort pulse laser crystal

  19. Charge-transfer state excitation as the main mechanism of the photodarkening process in ytterbium-doped aluminosilicate fibres

    Energy Technology Data Exchange (ETDEWEB)

    Bobkov, K K; Rybaltovsky, A A; Vel' miskin, V V; Likhachev, M E; Bubnov, M M; Dianov, E M [Fiber Optics Research Center, Russian Academy of Sciences, Moscow (Russian Federation); Umnikov, A A; Gur' yanov, A N; Vechkanov, N N [G.G.Devyatykh Institute of Chemistry of High-Purity Substances, Russian Academy of Sciences, Nizhnii Novgorod (Russian Federation); Shestakova, I A [Open Joint-Stock Company M.F. Stel' makh Polyus Research Institute, Moscow (Russian Federation)

    2014-12-31

    We have studied photodarkening in ytterbium-doped fibre preforms with an aluminosilicate glass core. Analysis of their absorption and luminescence spectra indicates the formation of stable Yb{sup 2+} ions in the glass network under IR laser pumping at a wavelength λ = 915 nm and under UV irradiation with an excimer laser (λ = 193 nm). We have performed comparative studies of the luminescence spectra of the preforms and crystals under excitation at a wavelength of 193 nm. The mechanism behind the formation of Yb{sup 2+} ions and aluminium – oxygen hole centres (Al-OHCs), common to ytterbium-doped YAG crystals and aluminosilicate glass, has been identified: photoinduced Yb{sup 3+} charge-transfer state excitation. (optical fibres)

  20. Evidence for two distinct defects contributing to the H4 deep-level transient spectroscopy peak in electron-irradiated InP

    International Nuclear Information System (INIS)

    Darwich, R.; Massarani, B.; Kaaka, M.; Awad, F.

    2000-01-01

    Deep-level transient spectroscopy (DLTS) has been used to study the dominant deep-level H4 produced in InP by electron irradiation. The characteristics of the H4 peak in Zn-doped Inp has been studied as a function of pulse duration (t p ) before and after annealing. The results show that at least two traps contribute to the H4 peak: one is a fast trap (labeled H4 f ) and the other is a show trap (labeled H4 s ). This is show through several results concerning the activation energy, the capture cross section, the full width at half-maximum, and the peak temperature shift. It is shown that both traps are irradiation defects created in P sublattice. (authors)

  1. Ce and Yb doped InP layers grown for radiation detection

    Czech Academy of Sciences Publication Activity Database

    Zavadil, Jiří; Procházková, Olga; Žďánský, Karel; Gladkov, Petar

    2007-01-01

    Roč. 4, č. 4 (2007), s. 1444-1447 ISSN 1610-1634. [EXMATEC 2006 - International Workshop on Expert Evaluation & Control of Compound Semiconductor Materials & Technologies /8./. Cádiz, 14.05.2006-17.05.2006] R&D Projects: GA ČR GA102/06/0153 Institutional research plan: CEZ:AV0Z20670512 Keywords : semiconductors * photoluminescence * galvanomagnetic effects Subject RIV: CA - Inorganic Chemistry

  2. The influence of ytterbium doping on the optical properties of tellurite glasses

    Energy Technology Data Exchange (ETDEWEB)

    Jaglarz, Janusz; Burtan, Bozena [Institute of Physics, Cracow University of Technology, ul. Podchorazych 1, 30-084 Cracow (Poland); Reben, Manuela; Wasylak, Jan [Faculty of Materials Science and Ceramics, AGH - University of Science and Technology, al. Mickiewicza 30, 30-059 Cracow (Poland); Cisowski, Jan [Institute of Physics, Cracow University of Technology, ul. Podchorazych 1, 30-084 Cracow (Poland); Centre of Polymer and Carbon Materials, Polish Academy of Sciences, ul. M. Curie-Sklodowskiej 34, 41-819 Zabrze (Poland); Jarzabek, Bozena [Centre of Polymer and Carbon Materials, Polish Academy of Sciences, ul. M. Curie-Sklodowskiej 34, 41-819 Zabrze (Poland)

    2011-09-15

    The goal of this work was to investigate the influence of rare earth ion Yb{sup 3+} doping on the thermal and optical properties of tellurite glass (TG) of the TeO{sub 2}-ZnO-PbO-La{sub 2}O{sub 3} system. The reflectance, transmittance and ellipsometric measurements have been done. Decreasing of the refractive index of TG with the Yb{sup 3+} ion doping has been concluded. For determination of the refractive index variation in the bulk, the small angle light scatter (SALS) measurements have been carried out. (copyright 2011 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

  3. Violet-green excitation for NIR luminescence of Yb3+ ions in Bi2O3-B2O3-SiO2-Ga2O3 glasses.

    Science.gov (United States)

    Li, Weiwei; Cheng, Jimeng; Zhao, Guoying; Chen, Wei; Hu, Lili; Guzik, Malgorzata; Boulon, Georges

    2014-04-21

    60Bi(2)O(3)-20B(2)O(3)-10SiO(2)-10Ga(2)O(3) glasses doped with 1-9 mol% Yb(2)O(3) were prepared and investigated mainly on their violet-green excitation for the typical NIR emission of Yb(3+), generally excited in the NIR. Two violet excitation bands at 365 nm and 405 nm are related to Yb(2+) and Bi(3+). 465 nm excitation band and 480 nm absorption band in the blue-green are assigned to Bi(0) metal nanoparticles/grains. Yb-content-dependence of the excitation and absorption means that Bi(0) is the reduced product of Bi(3+), but greatly competed by the redox reaction of Yb(2+) ↔ Yb(3+). It is proved that the violet-green excitations result in the NIR emission of Yb(3+). On the energy transfer, the virtual level of Yb(3+)-Yb(3+) as well as Bi(0) dimers probably plays an important role. An effective and controllable way is suggested to achieve nano-optical applications by Bi(0) metal nanoparticles/grains and Yb(3+).

  4. Study of Stark Effect in n-doped 1.55 μm InN0.92yP1-1.92yBiy/InP MQWs

    Science.gov (United States)

    Bilel, C.; Chakir, K.; Rebey, A.; Alrowaili, Z. A.

    2018-05-01

    The effect of an applied electric field on electronic band structure and optical absorption properties of n-doped InN0.92y P1-1.92y Bi y /InP multiple quantum wells (MQWs) was theoretically studied using a self-consistent calculation combined with the 16-band anti-crossing model. The incorporation of N and Bi atoms into an InP host matrix leads to rapid reduction of the band gap energy covering a large infrared range. The optimization of the well parameters, such as the well/barrier widths, N/Bi compositions and doping density, allowed us to obtain InN0.92y P1-1.92y Bi y /InP MQWs operating at the wavelength 1.55 μm. Application of the electric field causes a red-shift of the fundamental transition energy T 1 accompanied by a significant change in the spatial distribution of confined electron density. The Stark effect on the absorption coefficient of n-doped InN0.92y P1-1.92y Bi y /InP MQWs was investigated. The Bi composition of these MQWs was adjusted for each electric field value in order to maintain the wavelength emission at 1.55 μm.

  5. Synthesis and properties of ultra-long InP nanowires on glass.

    Science.gov (United States)

    Dhaka, Veer; Pale, Ville; Khayrudinov, Vladislav; Kakko, Joona-Pekko; Haggren, Tuomas; Jiang, Hua; Kauppinen, Esko; Lipsanen, Harri

    2016-12-16

    We report on the synthesis of Au-catalyzed InP nanowires (NWs) on low-cost glass substrates. Ultra-dense and ultra-long (up to ∼250 μm) InP NWs, with an exceptionally high growth rate of ∼25 μm min -1 , were grown directly on glass using metal organic vapor phase epitaxy (MOVPE). Structural properties of InP NWs grown on glass were similar to the ones grown typically on Si substrates showing many structural twin faults but the NWs on glass always exhibited a stronger photoluminescence (PL) intensity at room temperature. The PL measurements of NWs grown on glass reveal two additional prominent impurity related emission peaks at low temperature (10 K). In particular, the strongest unusual emission peak with an activation energy of 23.8 ± 2 meV was observed at 928 nm. Different possibilities including the role of native defects (phosphorus and/or indium vacancies) are discussed but most likely the origin of this PL peak is related to the impurity incorporation from the glass substrate. Furthermore, despite the presence of suspected impurities, the NWs on glass show outstanding light absorption in a wide spectral range (60%-95% for λ = 300-1600 nm). The optical properties and the NW growth mechanism on glass is discussed qualitatively. We attribute the exceptionally high growth rate mostly to the atmospheric pressure growth conditions of our MOVPE reactor and stronger PL intensity on glass due to the impurity doping. Overall, the III-V NWs grown on glass are similar to the ones grown on semiconductor substrates but offer additional advantages such as low-cost and light transparency.

  6. Color Tunable and Upconversion Luminescence in Yb-Tm Co-Doped Yttrium Phosphate Inverse Opal Photonic Crystals.

    Science.gov (United States)

    Wang, Siqin; Qiu, Jianbei; Wang, Qi; Zhou, Dacheng; Yang, Zhengwen

    2016-04-01

    For this paper, YPO4: Tm, Yb inverse opals with the photonic band gaps at 475 nm and 655 nm were prepared by polystyrene colloidal crystal templates. We investigated the influence of photonic band gaps on the Tm-Yb upconversion emission which was in the YPO4: Tm Yb inverse opal photonic crystals. Comparing with the reference sample, significant suppression of both the blue and red upconversion luminescence of Tm3+ ions were observed in the inverse opals. The color purity of the blue emission was improved in the inverse opal by the suppression of red upconversion emission. Additionally, mechanism of upconversion emission in the inverse opal was discussed. We believe that the present work will be valuable for not only the foundational study of upconversion emission modification but also the development of new optical devices in upconversion lighting and display.

  7. Electronic properties of GaAs, InAs and InP nanowires studied by terahertz spectroscopy

    International Nuclear Information System (INIS)

    Joyce, Hannah J; Docherty, Callum J; Lloyd-Hughes, James; Herz, Laura M; Johnston, Michael B; Gao Qiang; Tan, H Hoe; Jagadish, Chennupati

    2013-01-01

    We have performed a comparative study of ultrafast charge carrier dynamics in a range of III–V nanowires using optical pump–terahertz probe spectroscopy. This versatile technique allows measurement of important parameters for device applications, including carrier lifetimes, surface recombination velocities, carrier mobilities and donor doping levels. GaAs, InAs and InP nanowires of varying diameters were measured. For all samples, the electronic response was dominated by a pronounced surface plasmon mode. Of the three nanowire materials, InAs nanowires exhibited the highest electron mobilities of 6000 cm 2 V −1 s −1 , which highlights their potential for high mobility applications, such as field effect transistors. InP nanowires exhibited the longest carrier lifetimes and the lowest surface recombination velocity of 170 cm s −1 . This very low surface recombination velocity makes InP nanowires suitable for applications where carrier lifetime is crucial, such as in photovoltaics. In contrast, the carrier lifetimes in GaAs nanowires were extremely short, of the order of picoseconds, due to the high surface recombination velocity, which was measured as 5.4 × 10 5   cm s −1 . These findings will assist in the choice of nanowires for different applications, and identify the challenges in producing nanowires suitable for future electronic and optoelectronic devices. (paper)

  8. Upconversion in rare earth ions doped TeO2-ZnO glass

    International Nuclear Information System (INIS)

    Mohanty, Deepak Kumar; Rai, Vineet Kumar

    2012-01-01

    The Er 3+ /Yb 3+ doped/codoped TeO 2 -ZnO glasses have been fabricated by conventional melt and quenching technique. The absorption spectra of the doped/codoped glasses have been performed. The visible upconversion emissions of both doped and codoped glasses have been observed using 808 nm diode laser excitation. The process involved in upconversion emissions has been discussed in detail. (author)

  9. Dual functional NaYF4:Yb3+, Er3+@NaYF4:Yb3+, Nd3+ core-shell nanoparticles for cell temperature sensing and imaging

    Science.gov (United States)

    Shi, Zengliang; Duan, Yue; Zhu, Xingjun; Wang, Qiwei; Li, DongDong; Hu, Ke; Feng, Wei; Li, Fuyou; Xu, Chunxiang

    2018-03-01

    Lanthanide-doped up-conversion nanoparticles (UCNPs) provide a remote temperature sensing approach to monitoring biological microenvironments. In this research, the UCNPs of NaYF4:Yb3+, Er3+@NaYF4:Yb3+, Nd3+ with hexagonal (β)-phase were synthesized and applied in cell temperature sensing as well as imaging after surface modification with meso-2, 3-dimercaptosuccinic acid. In the core-shell UCNPs, Yb3+ ions were introduced as energy transfer media between sensitizers of Nd3+ and activators of Er3+ to improve Er3+emission and prevent their quenching behavior due to multiple energy levels of Nd3+. Under the excitations of 808 nm and 980 nm lasers, the NaYF4:Yb3+, Er3+@NaYF4:Yb3+, Nd3+ nanoparticles exhibited an efficient green band with two emission peaks at 525 nm and 545 nm, respectively, which originated from the transitions of 2H11/2 → 4I15/2 and 4S3/2 → 4I15/2 for Er3+ ions. We demonstrate that an occurrence of good logarithmic linearity exists between the intensity ratio of these two emission peaks and the reciprocal of the inside or outside temperature of NIH-3T3 cells. A better thermal stability is proved through temperature-dependent spectra with a heating-cooling cycle. The obtained viability of NIH-3T3 cells is greater than 90% after incubations of about 12 and 24 (h), and they possess a lower cytotoxicity of UCNPs. This work provides a method for monitoring the cell temperature and its living state from multiple dimensions including temperature response, cell images and visual up-conversion fluorescent color.

  10. High-gain polymer optical waveguide amplifiers based on core-shell NaYF4/NaLuF4: Yb3+, Er3+ NPs-PMMA covalent-linking nanocomposites

    Science.gov (United States)

    Zhang, Meiling; Zhang, Weiwei; Wang, Fei; Zhao, Dan; Qu, Chunyang; Wang, Xibin; Yi, Yunji; Cassan, Eric; Zhang, Daming

    2016-11-01

    Waveguide amplifiers have always been significant key components for optical communication. Unfortunately, the low concentration of rare earth ions doped in the host material and the inadequate optimization of the waveguide structure have been the common bottleneck limitations. Here, a novel material, NaYF4/NaLuF4: 20% Yb3+, 2% Er3+ nanoparticle-Polymeric Methyl Methacrylate covalent-linking nanocomposite, was synthesized. The concentrations of Er3+ and Yb3+ doping increased an order of magnitude. Under a 980 nm laser excitation, highly efficient emission at 1.53 μm was obtained. The characteristic parameters of the single mode waveguide were carefully designed and optimized by using a finite difference method. A formulized iteration method is presented for solving the rate equations and the propagation equations of the EYCDWA, and both the steady state behavior and the gain were numerically simulated. The optimal Er3+ and Yb3+ concentrations are 2.8 × 1026 m-3 and 2.8 × 1027 m-3, and the optimal waveguide length is 1.3 cm. Both theoretical and experimental results indicated that, for an input signal power of 0.1 mW and a pump power of 400 mW, a net gain of 15.1 dB at 1530 nm is demonstrated. This result is the highest gain ever reported in polymer-based waveguide amplifiers doped with inorganic Er3+-Yb3+ codoped nanocrystals.

  11. Cooperative emission in ion implanted Yb:YAG waveguides

    Energy Technology Data Exchange (ETDEWEB)

    Vazquez, G V; Desirena, H; De la Rosa, E [Centro de Investigaciones en Optica, Loma del Bosque 115, Lomas del Campestre, 37150 Leon, Guanajuato (Mexico); Flores-Romero, E; Rickards, J; Trejo-Luna, R [Instituto de Fisica, UNAM, Apartado Postal 20364, 01000 Mexico, D. F. (Mexico); Marquez, H, E-mail: gvvazquez@cio.mx [Departamento de Optica, CICESE, Km 107 Carr. Tijuana-Ensenada, 22860 Ensenada, B. C. (Mexico)

    2011-01-01

    In this work, we report the analysis of spectroscopic properties of waveguides fabricated by ion implantation in YAG doped with Yb{sup 3+} ions. Three emission bands were detected in the blue, green and red regions under 970-nm excitation. The strong blue-green emission can be explained by a cooperative process between ytterbium ion pairs, leading to emission centered at 514 nm. The additional blue bands as well as green and red emission bands are attributed to the presence of Tm{sup 3+} and Er{sup 3+} traces. The results include absorption and emission curves as well as decay time rates.

  12. Cooperative emission in ion implanted Yb:YAG waveguides

    International Nuclear Information System (INIS)

    Vazquez, G V; Desirena, H; De la Rosa, E; Flores-Romero, E; Rickards, J; Trejo-Luna, R; Marquez, H

    2011-01-01

    In this work, we report the analysis of spectroscopic properties of waveguides fabricated by ion implantation in YAG doped with Yb 3+ ions. Three emission bands were detected in the blue, green and red regions under 970-nm excitation. The strong blue-green emission can be explained by a cooperative process between ytterbium ion pairs, leading to emission centered at 514 nm. The additional blue bands as well as green and red emission bands are attributed to the presence of Tm 3+ and Er 3+ traces. The results include absorption and emission curves as well as decay time rates.

  13. High detection performance of particle detectors based on SI InP doped with Ti and Zn

    Czech Academy of Sciences Publication Activity Database

    Gorodynskyy, Vladyslav; Yatskiv, Roman; Žďánský, Karel; Pekárek, Ladislav

    2008-01-01

    Roč. 55, č. 5 (2008), s. 2785-2788 ISSN 0018-9499 R&D Projects: GA AV ČR KAN400670651 Institutional research plan: CEZ:AV0Z10100520; CEZ:AV0Z20670512 Keywords : radiation detection * InP * crystal growth Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 1.518, year: 2008

  14. Heteroepitaxially grown InP solar cells

    International Nuclear Information System (INIS)

    Weinberg, I.; Swartz, C.K.; Brinker, D.J.; Wilt, D.M.

    1990-01-01

    Although they are significantly more radiation resistant than either Si or GaAs solar cells, their high wafer cost presents a barrier to the widespread use of InP solar cells in space. For this reason, the authors have initiated a program aimed at producing high efficiency, radiation resistant solar cells processed from InP heteroepitaxially grown on cheaper substrates. The authors' objective is to present the most recent results emanating from this program together with the results of their initial proton irradiations on these cells. This paper reports that InP cells were processed from a 4 micron layer of InP, grown by OMCVD on a silicon substrate, with a 0.5 micron buffer layer between the InP directly grown on a GaAs substrate. Initial feasibility studies, in a Lewis sponsored program at the Spire corporation, resulted in air mass zero efficiencies of 7.1% for the former cells and 9.1% for the latter. These initial low efficiencies are attributed to the high dislocation densities caused by lattice mismatch. The authors' preirradiation analysis indicates extremely low minority carrier diffusion lengths, in both cell base and emitter, and high values of both the diffusion and recombination components of the diode reverse saturation currents. Irradiation by 10 MeV protons, to a fluence of 10 13 cm -2 , resulted in relatively low degradation in cell efficiency, short circuit current and open circuit voltage

  15. Structure-property relations in new fluorophosphate glasses singly- and co-doped with Er3+ and Yb3+

    International Nuclear Information System (INIS)

    Gonçalves, Tássia S.; Moreira Silva, Raphaell J.; Oliveira Junior, Marcos de; Ferrari, Cynthia R.; Poirier, Gäel Y.; Eckert, Hellmut; Camargo, Andrea S.S. de

    2015-01-01

    Rare earth (RE 3+ )-doped fluorophosphate glasses are among the most promising candidates for high-efficiency laser generation in the near-infrared spectral region. By proper choice of composition, these materials can combine the advantages of fluorides (low phonon energies, low refractive indices, extensive optical window, low hygroscopicity) and of oxides (high chemical and mechanical stability and high dopant solubility), resulting in enhancement of the RE 3+ emissive properties. In this work, we present the synthesis and structural/spectroscopic investigation of new glasses with composition 25BaF 2 25SrF 2 (30-x)Al(PO 3 ) 3 xAlF 3 (20-z)YF 3 :zREF 3 , where x = 20 or 15, RE = Er 3+ and/or Yb 3+ , z = 0.25–5.0 mol%. Results indicate considerable improvement of the emissive properties of both ions when compared to phosphate or even other fluorophosphate host compositions. Long excited state lifetimes (τ = 10 ms for the Er 3+ level 4 I 13/2 , and τ = 1.3 ms for the Yb 3+ level 2 F 5/2 ) imply high fluorescence quantum efficiencies η (up to 85% for both ions). Structural characterization by Raman and multinuclear solid state NMR spectroscopies indicate that the metaphosphate-type chain structure of the Al(PO 3 ) 3 vitreous framework is partially depolymerized and dominated by Q (0) and Q (1) units crosslinked by six-coordinate Al species. As revealed by 27 Al{ 31 P} rotational echo double resonance (REDOR) NMR results the average local aluminum environment of the x = 20 sample comprises 1.6 phosphate and 4.4 fluoride species. These results indicate a clear bonding preference between aluminum and phosphorus, which is consistent with the desired dominance of fluoride species in the local environment of the rare earth and alkaline earth atoms in these glasses. - Highlights: • New fluorophosphate glass composition with excellent photophysical properties. • Detailed structural insights by multinuclear solid state NMR. • Rare earth bonding preference to

  16. Spectroscopic and laser investigations of Nd3+ and Yb3+ in rare-earth oxyborates

    International Nuclear Information System (INIS)

    Lupei, A.; Lupei, V.; Gheorghe, L.; Aka, G.; Vivien, D.; Antic- Fidancev, E.

    2002-01-01

    Since 1997 a new class of non-linear crystals have been intensively investigated, the rare-earth and calcium oxyborates RECa 4 O(BO 3 ) 4 -RECOB (especially with RE 3+ = Y 3+ or Gd 3+ ). These crystals can be grown from melt and have large effective non-linear coefficients; they present a large transparence range from 0.2-5 mm, are non-hygroscopic, have a high damage threshold, can be doped with large concentrations of laser active ions, etc. Undoped these crystals are good doublers and doped with Nd 3+ or Yb 3+ they can be used in the self - conversion regime for transformation of the infrared radiation into green, blue or red. A series of fundamental structural, spectroscopic and laser emission characteristics of Nd 3+ or Yb 3+ doped RECOB are still under study. Thus, one important aspect discussed in literature is the degree of disorder of RECOB crystals. The research performed in the frame of CERES project was devoted to the growth of the of RECOB crystals doped with Nd 3+ or Yb 3+ , structural investigations and high-resolution optical spectral investigations and Nd 3+ laser emission. The growth of RECa 4 O(BO) 3 (Y 3+ and Gd 3+ ) single crystals was performed with an ADL furnace by using Czochralski method. Good optical crystals were obtained on direction; X-ray structural studies were also performed. The low temperatures high-resolution optical spectral measurements on Nd 3+ and Yb 3+ doped GdCOB and YCOB allowed the clarification of some structural characteristics of these crystals. Two problems were studied: the intrinsic structure of undoped crystals and the doping effects. Studies revealed for the first time by optical spectroscopy essential differences between GdCOB and YCOB crystals; they refer to the satellite structure of Yb 3+ or Nd 3+ and inhomogeneous broadening, indicating a disordered structure much larger for YCOB, qualitatively in accord with recent X-ray results. Based on spectral, emission decay and structural investigations, models for

  17. Indium phosphide (InP) for optical interconnects

    NARCIS (Netherlands)

    Lebby, M.; Ristic, S.; Calabretta, N.; Stabile, R.; Tekin, T.; Pitwon, R.; Håkansson, A.; Pleros, N.

    2016-01-01

    We present InP as the incumbent technology for data center transceiver and switching optics. We review the most popular InP monolithic integration approaches in light of photonic integration being recognized as an increasingly important technology for data center optics. We present Multi-Guide

  18. The down-conversion and up-conversion photoluminescence properties of Na0.5Bi0.5TiO3:Yb3+/Pr3+ ceramics

    International Nuclear Information System (INIS)

    Huang, Yinpeng; Luo, Laihui; Wang, Jia; Zuo, Qianghui; Yao, Yongjie; Li, Weiping

    2015-01-01

    Na 0.5 Bi 0.5−x−y Yb x Pr y TiO 3 (NBT:xYb/yPr) ceramics with different Yb and Pr contents are prepared. Both the down-conversion (DC) and up-conversion (UC) photoluminescence (PL) of the ceramics via 453 and 980 nm excitation, respectively, are investigated. The effect of Yb 3+ and Pr 3+ doping contents on the DC and UC PL is significantly different from each other. Furthermore, the UC PL of the ceramics as a function of temperatures is measured to investigate the UC process in detail. Based on energy level diagram of Pr 3+ and Yb 3+ ions and the DC and UC PL spectra, the DC and UC PL mechanisms of Pr 3+ and Yb 3+ ions are discussed. Especially, the UC PL mechanism is clarified, which is different from the previously reported literature. Also, the temperature sensing properties of the ceramics are studied based on the photoluminescence ratio technique, using the thermal coupling energy levels of Pr 3+

  19. Luminescence and color center distributions in K3YB6O12:Ce3+ phosphor

    International Nuclear Information System (INIS)

    Yang, Li; Wan, Yingpeng; Weng, Honggen; Huang, Yanlin; Chen, Cuili; Seo, Hyo Jin

    2016-01-01

    Polycrystalline Ce 3+ -doped K 3 YB 6 O 12 (1–14 mol%) phosphors were prepared by facile chemical sol–gel synthesis. The phase formation of the phosphors was confirmed by x-ray powder diffraction (XRD) analysis. The photoluminescence excitation spectra (PLE), emission spectra (PL) and the luminescence decay curves were tested. Under the near-UV light, the phosphors present the emission from blue color to yellowish green due to the allowed 4 f  –5 d transitions of Ce 3+ ions. The absolute quantum efficiency (QE) of K 3 YB 6 O 12 :Ce 3+ can reach 53% under the excitation of near-UV light. The luminescence thermal quenching of the phosphor was investigated by the temperature-dependent spectra. The crystallographic site of Ce 3+ ions in the lattice was identified and discussed on the basis of luminescence characteristics and structural data. There is only one isolated Ce 3+ center occupying the Y(II) sites in the lightly doped samples presenting a typical doublet emission profile. While the Ce 3+ multi-centers could be created with the enhancement of the doping levels, which could induce the distinct red-shift of the spectra due to the dipole–dipole interactions. The result in this work could be useful for the further investigation of other rare earth ions in this host. (paper)

  20. Preparation and luminescence properties of LaPO{sub 4}:Er,Yb nanoparticles

    Energy Technology Data Exchange (ETDEWEB)

    Jung, Ha-Kyun [Advanced Materials Division, Korea Research Institute of Chemical Technology, P.O. Box 107, Yuseong, Daejeon 305-600 (Korea, Republic of)]. E-mail: hakyun@krict.re.kr; Oh, Jae-Suk [Advanced Materials Division, Korea Research Institute of Chemical Technology, P.O. Box 107, Yuseong, Daejeon 305-600 (Korea, Republic of); Seok, Sang-Il [Advanced Materials Division, Korea Research Institute of Chemical Technology, P.O. Box 107, Yuseong, Daejeon 305-600 (Korea, Republic of); Lee, Tack-Hyuck [Department of Chemistry, Paichai University, Daejeon 302-735 (Korea, Republic of)

    2005-09-15

    For possible applications as optical amplification materials in telecommunications, LaPO{sub 4}:Er,Yb nanoparticles were synthesized in a solution system and their properties were investigated by various spectroscopic techniques. The prepared nanoparticles are single-phased and present the monazite structure, the particle size being about 5 nm with a narrow size distribution. Also, it was confirmed by EA and FT-IR analyses that the surface of nanoparticles is coated with the solvent molecules used in the synthesis reaction, which possibly prevents them from agglomerating. In the NIR region, the emission of the LaPO{sub 4}:Er particles is very weak due to an efficient quenching of the {sup 4}I{sub 13/2}{yields}{sup 4}I{sub 15/2} emission by the hydroxyl groups adsorbed on the surface of the nanoparticles. On the other hand, the co-doping of Yb{sup 3+} as a sensitizer in the nanoparticles resulted in the increase of the emission intensity at 1539 nm due to the effective energy transfer from Yb{sup 3+} to Er{sup 3+}. In addition, the synthesized nanoparticles have exhibited good dispersibility into a polymer matrix and effective luminescence in the NIR region.

  1. Thermal diffusion in nanostructured porous InP

    Indian Academy of Sciences (India)

    Nanostructured porous InP samples were prepared by electrochemical anodic dissolution of InP for various current densities and etching periods. The samples were characterized by SEM and photoluminescence (PL) where a blue shift was observed in PL. Thermal properties studied by photoacoustic (PA) spectroscopy ...

  2. One-pot synthesis of hollow structured upconversion luminescent β-NaYF4:Yb0.2Er0.02 nanoparticles

    International Nuclear Information System (INIS)

    Wu, Qinglong; Pei, Jianfeng; De, Gejihu

    2014-01-01

    Monodisperse, uniform, and hollow structured hexagonal sodium yttrium fluoride nanoparticles co-doped with Yb 3+ and Er 3+ (NaYF 4 :Yb 3+ , Er 3+ ) were successfully prepared by a facile one-pot thermal decomposition route. The crystal structure, morphology and upconversion spectra of the sample were investigated using X-ray powder diffractometer, transmission electron microscope, and fluorescence spectrophotometer with an external 980 nm single-wavelength diode laser. The synthesized nanoparticles were easily dispersed in nonpolar solvents, showed an extremely narrow particle distribution, and were determined to have a diameter about (14.3)±(1.1) nm. Moreover, the nanoparticles were dispersed in water via modification of the capping oleic acid ligand by HCl. To the synthesis of such monidisperse, water-soluble, hollow structured lanthanide-doped upconversion nanoparticles may lead to potential applications in drug delivery and bioimaging. - Highlights: • Hollow structured hexagonal NaYF 4 :Yb 0.2 Er 0.02 luminescent nanoparticles were prepared by a facile one-pot thermal decomposition route. • HCl was used to render the nanoparticles to water solubility. • The bright green light and transparent solution indicate that as-treated water-soluble nanoparticles may lead to potential applications in drug delivery and bioimaging

  3. The design and manufacture of a notch structure for a planar InP Gunn diode

    International Nuclear Information System (INIS)

    Bai Yang; Jia Rui; Wu De-Qi; Jin Zhi; Liu Xin-Yu

    2013-01-01

    A planar InP-based Gunn diode with a notch doping structure is designed and fabricated for integration into millimeter-wave and terahertz integrated circuits. We design two kinds of InP-based Gunn diodes. One has a fixed diameter of cathode area, but has variable spacing between anode and cathode; the other has fixed spacing, but a varying diameter. The threshold voltage and saturated current exhibit their strong dependences on the spacing (10 μm–20 μm) and diameter (40 μm–60 μm) of the InP Gunn diode. The threshold voltage is approximately 4.5 V and the saturated current is in a range of 293 mA–397 mA. In this work, the diameter of the diode and the space between anode and cathode are optimized. The devices are fabricated using a wet etching technique and show excellent performances. The results strongly suggest that low-cost and reliable InP planar Gunn diodes can be used as single chip terahertz sources. (condensed matter: electronic structure, electrical, magnetic, and optical properties)

  4. Progress in InP solar cell research

    International Nuclear Information System (INIS)

    Weinberg, I.; Brinker, D.J.

    1988-01-01

    Progress, in the past year, in InP solar cell research is reviewed. Small area cells with AMO, total area efficiencies of 18.8 percent were produced by OMCVD and Ion Implantation. Larger area cells (2 and 4 sq cm) were processed on a production basis. One thousand of the 2 sq cm cells will be used to supply power to a small piggyback lunar orbiter scheduled for launch in February 1990. Laboratory tests of ITO/InP cells, under 10 MeV proton irradiation, indicate radiation resistance comparable to InP n/p homojunction cells. Computer modeling studies indicate that, for identical geometries and dopant concentrations, InP solar cells are significantly more radiation resistant than GaAs under 1 MeV electron irradiation. Additional computer modeling calculations were used to produce rectangular and circular InP concentrator cell designs for both the low concentration SLATS and higher concentration Cassegrainian Concentrators

  5. Studies on semiconductors based on InP with sub-ps response times

    International Nuclear Information System (INIS)

    Biermann, K.

    2007-01-01

    The present work describes investigation of new material concepts accomplished using molecular-beam-epitaxy (MBE) growth for application in ultra-fast photonic components. Nominally undoped and Be doped GaInAs/AlInAs multiple-quantumwell structures (MQW) were grown by MBE at growth temperatures down to 100 C (LT-MBE) on semi-insulating InP substrates. Crystalline, electric and optical properties of as-grown and annealed structures were investigated. Energy states near the conduction band of GaInAs determine the electrical and optical properties of LT-MQWs. The dynamics of charge carrier relaxation was studied by means of pump and probe experiments. Measurements of the differential transmission when excited by an additional cw laser and measurements utilizing two closely sequenced pump pulses support the capability of Be doped as-grown (annealed) LT GaInAs/AlInAs MQW structures for use in optical switches at switching frequencies in the 1 Tbit/s (250 Gbit/s) range. The voltage-induced change of interband transmission of InP based quantumcascade-lasers (QCL) during pulsed mode operation was analyzed by means of 8 band k.p calculations. The impacts of varying charge carrier distributions and of electrically heated samples can be neglected compared to the dominating effect of the electrical field on the interband transmission. The impact of MBE growth parameters on the interface quality of AlAsSb/ GaInAs heterostructures were determined by means of Hall measurements, temperature- and intensity-dependent PL measurements and spectral measurements of the interband- and intersubband-absorption. The impact of In segregation and Sb diffusion on the intersubband absorption was analyzed on the basis of bandstructure calculations. Intersubband transitions at wavelengths of about 1.8 μm (1.55 μm) were successfully achieved in MQW (coupled QW) structures. (orig.)

  6. InP nanopore arrays for photoelectrochemical hydrogen generation.

    Science.gov (United States)

    Li, Qiang; Zheng, Maojun; Zhang, Bin; Zhu, Changqing; Wang, Faze; Song, Jingnan; Zhong, Miao; Ma, Li; Shen, Wenzhong

    2016-02-19

    We report a facile and large-scale fabrication of highly ordered one-dimensional (1D) indium phosphide (InP) nanopore arrays (NPs) and their application as photoelectrodes for photoelectrochemical (PEC) hydrogen production. These InP NPs exhibit superior PEC performance due to their excellent light-trapping characteristics, high-quality 1D conducting channels and large surface areas. The photocurrent density of optimized InP NPs is 8.9 times higher than that of planar counterpart at an applied potential of +0.3 V versus RHE under AM 1.5G illumination (100 mW cm(-2)). In addition, the onset potential of InP NPs exhibits 105 mV of cathodic shift relative to planar control. The superior performance of the nanoporous samples is further explained by Mott-Schottky and electrochemical impedance spectroscopy ananlysis.

  7. Effect of silver nanoparticles on the 1.53 μm fluorescence in Er3+/Yb3+ codoped tellurite glasses

    Science.gov (United States)

    Wu, Libo; Zhou, Yaxun; Zhou, Zizhong; Cheng, Pan; Huang, Bo; Yang, Fengjing; Li, Jun

    2016-07-01

    Improving the spectroscopic properties of rare earth (RE) doped glass materials is a challenging task. In the present work the metallic silver nanoparticles (Ag NPs) were embedded into Er3+/Yb3+ codoped tellurite glasses with composition TeO2-Bi2O3-TiO2, prepared using melt-quenching and subsequent heat-treated techniques, and the improved effect of Ag NPs on the 1.53 μm band fluorescence of Er3+ ions was investigated. About 24 h heat-treatment of Er3+/Yb3+ codoped tellurite glass containing 1 mol % amount of AgNO3 at the temperature 370 °C yielded the well-dispersed and near-spherical Ag NPs with ∼11.4 nm average diameter as evidenced by transmission electron microscopy (TEM) image. The intense 1.53 μm band fluorescence was observed in the prepared Er3+/Yb3+ codoped tellurite glasses under the excitation of 980 nm and was further improved with the presence of Ag NPs in the glass matrix, which is attributed to the enhanced local electric field around doped RE ions induced by Ag NPs and the possible energy transfer from Ag NPs to Er3+ ions. The enhanced local electric field was well demonstrated by comparing the variation of emission spectra of hypersensitive probe Eu3+ ions in tellurite glasses with and without Ag NPs. From the Judd-Ofelt analysis, it was also found that the value of Ω6 intensity parameter increased slightly with the increase of Ag NPs concentration in a certain range, also confirming the possibility of realizing strong fluorescence emission. In addition, the amorphous structural nature was demonstrated by the measured X-ray diffraction (XRD) patterns with no sharp diffraction peak. The enhanced 1.53 μm band fluorescence indicates that the Er3+/Yb3+ codoped tellurite glass with an appropriate amount of Ag NPs is a promising candidate for the development of Er3+-doped fiber amplifiers (EDFAs) applied in the WDM systems.

  8. High temperature luminescence of ZnSe:Yb crystals

    Directory of Open Access Journals (Sweden)

    Makhniy V. P.

    2016-05-01

    Full Text Available The problem of obtaining of effective edge luminescence with high temperature stability in the zinc selenide crystals is discussed. This task is solved by using as the dopant rare-earth element yttrium, which is introduced into the undoped ZnSe crystal by diffusion method. Doping was carried out in an evacuated to 10 -4 Torr. and a sealed quartz ampoule, in the opposite ends of which is a sample and a mixture of the crushed Yb and Se. It has been found that the diffusion coefficient of yttrium at a temperature of 1400 K is about 5⋅10 -7 cm 2/sec. It is shown that in the luminescence spectra of ZnSe:Yb samples in the temperature range 295-470 K only blue band is observed. Dependencies of parameters of this band from the excitation level are typical for the annihilation of excitons at their inelastic scattering by free carriers. The efficacy of blue radiation at 300 K is about 30% and does not fall more than twice with increasing temperature up to 470 K, indicating its high thermal stability.

  9. Yb3+:Sr5(VO4)3F: Crystal growth, spectroscopic characterization and laser development

    International Nuclear Information System (INIS)

    Bustamante, Andrea Nora Pino

    1999-01-01

    Crystal growth, spectroscopic characterization and laser development of Yb 3+ :SVAP [Sr 5 (VO 4 ) 3 F] was performed to demonstrate for the first time, operation of tunable laser emission centered at 1120 nm. Initially, SVAP crystals were grown with high dopant concentrations, up to 6.0 mol % of Yb 2 O 3 in the melt, in order to investigate the material for potential laser operation at a new laser wavelength. Additional research was performed to alleviate highly doped SVAP crystals of defects previously observed. Basic spectroscopic characterization including absorption and luminescent properties were measured to better understand the behavior of Yb 3+ ions in SVAP. Based upon these studies, discussion of the 1120 nm laser transition is presented as it arises from a ground state vibrational level. Investigations of the charge compensation process and the optical parameters as a function of dopant concentration are also presented. The laser development of Yb 3+ :SVAP included continuous and pulsed modes of operation of the 1044 nm and 1120 nm transitions. Initial laser action of the 1044 nm transition was achieved using a Yi: Saphire laser pump source in order to compare with previously results. Further development of a diode-pumped Yb 3+ :SVAP laser system demonstrated continuously tunable laser operation from 1103 nm for the first time. The laser investigations also proved that this high gain media does provide continuous wave laser action at 1044 nm and 1120 simultaneously without significant gain depletion. (author)

  10. Effects of the electron beam on InP(100)

    International Nuclear Information System (INIS)

    Bouslama, M.; Jardin, C.; Ghamnia, M.

    1996-01-01

    Auger Electron Spectroscopy (AES) is performed to monitor the InP(100) surface evolution while it is irradiated by an electron beam of 5 KeV energy and 10 -3 A.cm -2 current density. A charge phenomenon appears during the irradiation of sputter-cleaned InP(100) by Ar + at low energy (500 eV). The deposition of phosphorus or antimony at room temperature on cleaned InP(100) is a good way of preventing this charging problem. This is also achieved by the growth of stoichiometric indium phosphide on InP(100) substrate, from an injection of phosphine and indium trimethyl whose ratio V/III is of 50, in a MOCVD (Metal Organic Chemical Vapor Deposition) reactor. The electron beam even acts to stimulate oxidation of the stoichiometric InP(100) surface involving on the top layers, into a well defined oxide such as InPO 4 or a contamination layer composed of carbon and oxygen. The partial pressure in the spectrometer is about 10 -9 Torr. The incident electrons produce breaking of (In-P) chemical bonds so that the resulting indium takes part in the oxidation process. The phosphorus is thought to be desorbed from the surface. (author)

  11. High conversion efficiency and high radiation resistance InP solar cells

    International Nuclear Information System (INIS)

    Yamamoto, Akio; Itoh, Yoshio; Yamaguchi, Masafumi

    1987-01-01

    The fabrication of homojunction InP solar cells has been studied using impurity thermal diffusion, organometallic vapor phase epitaxy (OMVPE) and liquid phase epitaxy (LPE), and is discussed in this paper. Conversion efficiencies exceeding 20 % (AM1.5) are attained. These are the most efficient results ever reported for InP cells, and are comparable to those for GaAs cells. Electron and γ-ray irradiation studies have also been conducted for fabricated InP cells. The InP cells were found to have higher radiation resistance than GaAs cells. Through these studies, it has been demonstrated that the InP cells have excellent potential for space application. (author)

  12. Enhanced ~2.7 µm emission investigation of Er{sup 3+}:{sup 4}I{sub 11/2}→{sup 4}I{sub 13/2} transition in Yb,Er,Pr:SrLaGa{sub 3}O{sub 7} crystal

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Yan [Key Laboratory of Optoelectronic Materials Chemistry and Physics, Fujian Institute of Research on the Structure of Matter, Chinese Academy of Sciences, Fuzhou, Fujian 350002 (China); Zhang, Baotong [Key Laboratory of Optoelectronic Materials Chemistry and Physics, Fujian Institute of Research on the Structure of Matter, Chinese Academy of Sciences, Fuzhou, Fujian 350002 (China); College of Materials Science and Engineering, Fujian Normal University, Fuzhou, Fujian 350007 (China); Li, Jianfu; Zhu, Zhaojie; You, Zhenyu [Key Laboratory of Optoelectronic Materials Chemistry and Physics, Fujian Institute of Research on the Structure of Matter, Chinese Academy of Sciences, Fuzhou, Fujian 350002 (China); Tu, Chaoyang, E-mail: tcy@fjirsm.ac.cn [Key Laboratory of Optoelectronic Materials Chemistry and Physics, Fujian Institute of Research on the Structure of Matter, Chinese Academy of Sciences, Fuzhou, Fujian 350002 (China)

    2017-03-15

    The bulk crystal of 5at% Yb{sup 3+}, 20 at% Er{sup 3+} and 0.2 at% Pr{sup 3+} triply doped SrLaGa{sub 3}O{sub 7} (abbr. as Yb,Er,Pr:SLGO) was grown by the Czochralski method. The effects of co-dopant Yb{sup 3+} and Pr{sup 3+} on the spectroscopic properties and the mutual energy transfer mechanism were investigated, via the measurements of its absorption, near-infrared and mid-infrared fluorescence spectra, as well as the fluorescence decay curves of Er{sup 3+}:{sup 4}I{sub 13/2} and {sup 4}I{sub 11/2} levels at room temperature. As compared with 20at% Er{sup 3+} singly doped SrLaGa{sub 3}O{sub 7} crystal, ~2.7 µm emission intensity corresponding to Er{sup 3+}:{sup 4}I{sub 11/2}→{sup 4}I{sub 13/2} transition is enhanced greatly in the Yb,Er,Pr:SLGO crystal. Spectral analyses indicate that the sensitization of Yb{sup 3+} to Er{sup 3+} improves the ~2.7 µm emission in Yb,Er,Pr:SLGO crystal, meanwhile, the depopulation of Pr{sup 3+} from Er{sup 3+} decreases the ~1.5 µm emission and inhibits the self-termination effect. The energy transfer efficiencies of Yb{sup 3+}→Er{sup 3+} (ET1), Er{sup 3+}→Pr{sup 3+} (ET2) and Er{sup 3+}→Pr{sup 3+} (ET3) were estimated and discussed. The above results conclude that Yb,Er,Pr:SLGO crystal is a good candidate for LD pumped mid-infrared laser. - Graphical abstract: As compared with Er: SrLaGa{sub 3}O{sub 7} crystal, ~2.7 µm MIR emissions corresponding to Er{sup 3+}:{sup 4}I{sub 11/2}→{sup 4}I{sub 13/2} transition were enhanced in Yb{sup 3+}, Er{sup 3+} and Pr{sup 3+} triply doped SrLaGa{sub 3}O{sub 7} crystal owing to the sensitization of co-dopant Yb{sup 3+} via ET1, at the same time, ~1.5 µm NIR emissions were weakened owing to the depopulation of co-dopant Pr{sup 3+} via ET3.

  13. Continuous-wave green thin-disk laser at 524 nm based on frequency-doubled diode-pumped Yb:GSO crystal

    International Nuclear Information System (INIS)

    Shao, Y; Zhang, D; Liu, H P; Jin, H J; Li, Y L; Tao, Z H; Ruan, Q R; Zhang, T Y

    2011-01-01

    We report what is believed to be the first demonstration of diode-pumped continuous-wave (CW) thin-disk Yb 3+ -doped Gd 2 SiO 5 (Yb:GSO) laser at 1048 nm. With a 3.8% output coupler, the maximum output power is 1.38 W under a pump power of 17.8 W. Moreover, intracavity second-harmonic generation (SHG) has also been achieved with a power of 337 mW at 524 nm by using a LiB 3 O 5 (LBO) nonlinear crystal. At the output power level of 337 mW, the green power stability is better than 5% and the ellipticity of spot is 0.97

  14. Sequential growth of sandwiched NaYF{sub 4}:Yb/Er@NaYF{sub 4}:Yb@NaNdF{sub 4}:Yb core–shell–shell nanoparticles for photodynamic therapy

    Energy Technology Data Exchange (ETDEWEB)

    Peng, Huang-Yong; Ding, Bin-Bin; Ma, Yin-Chu [Department of Medical Materials and Rehabilitation Engineering, School of Medical Engineering, Hefei University of Technology, Hefei 230009 (China); Sun, Shi-Qi [State Key Laboratory of Veterinary Etiological Biology and Key Laboratory of Animal Virology of Ministry of Agriculture, Lanzhou Veterinary Research Institute, Chinese Academy of Agricultural Sciences, Xujiaping 1, Lanzhou, Gansu 730046 (China); Tao, Wei [Department of Medical Materials and Rehabilitation Engineering, School of Medical Engineering, Hefei University of Technology, Hefei 230009 (China); Guo, Yan-Chuan [Technical Institute of Physics and Chemistry, Chinese Academy of Sciences, Beijing 100190 (China); Guo, Hui-Chen, E-mail: ghch-2004@hotmail.com [State Key Laboratory of Veterinary Etiological Biology and Key Laboratory of Animal Virology of Ministry of Agriculture, Lanzhou Veterinary Research Institute, Chinese Academy of Agricultural Sciences, Xujiaping 1, Lanzhou, Gansu 730046 (China); Yang, Xian-Zhu, E-mail: yangxz@hftu.edu.cn [Department of Medical Materials and Rehabilitation Engineering, School of Medical Engineering, Hefei University of Technology, Hefei 230009 (China); Qian, Hai-Sheng, E-mail: shqian@hfut.edu.cn [Department of Medical Materials and Rehabilitation Engineering, School of Medical Engineering, Hefei University of Technology, Hefei 230009 (China)

    2015-12-01

    Graphical abstract: The monodisperse elliptical NaYF{sub 4}:Yb/Er@NaYF{sub 4}:Yb@NaNdF{sub 4}:Yb core–shell–shell nanoparticles have been synthesized successfully by a facile sequential growth process, which can be used as transducer for photodynamic therapy of cancer cells. - Highlights: • The NaYF{sub 4}:Yb/Er@NaYF{sub 4}:Yb@NaNdF{sub 4}:Yb nanoparticles have been fabricated successfully. • The as-prepared nanoparticles show strong fluorescence excited at 980 or 808 nm. • The nanoparticles were transferred into the aqueous phase via a facile process. • Photosensitizers were loaded into the composites for photodynamic therapy. - Abstract: Upconversion (UC) nanostructures have attracted much interest for their extensive biological applications. In this work, we describe a sequential synthetic route to prepare sandwiched NaYF{sub 4}:Yb/Er@NaYF{sub 4}:Yb@NaNdF{sub 4}:Yb core–shell upconversion nanoparticles. The as-prepared products were investigated by X-ray diffraction (XRD) and transmission electron microscopy (TEM, JEM 2100F), respectively. The as-prepared core–shell nanoparticles of NaYF{sub 4}:Yb/Er@NaYF{sub 4}:Yb@NaNdF{sub 4}:Yb are composed of elliptical nanoparticles with a length of 80 nm and width of 42 nm, which show efficient upconversion fluorescence excited at 808 nm indicating the formation of core–shell–shell sandwiched nanostructures. In addition, the as-prepared sandwiched NaYF{sub 4}:Yb/Er@NaYF{sub 4}:Yb@NaNdF{sub 4}:Yb core–shell upconversion nanoparticles also show strong upconversion fluorescence excited at 980 nm. Amphiphilic mPEG{sub 2k}-b-PEBEP{sub 6K} copolymers (denoted as PPE) were chosen to transfer these hydrophobic UCNPs into the aqueous phase for biological application. In vitro photodynamic therapy of cancer cells show that the viability of cells incubated with the nanoparticles loaded with MC 540 was significantly lower as compared to the nanoparticles without photosensitizers exposed to NIR laser.

  15. Role of Gd{sup 3+} ion on downshifting and upconversion emission properties of Pr{sup 3+}, Yb{sup 3+} co-doped YNbO{sub 4} phosphor and sensitization effect of Bi{sup 3+} ion

    Energy Technology Data Exchange (ETDEWEB)

    Dwivedi, A.; Rai, S. B., E-mail: sbrai49@yahoo.co.in [Department of Physics, Banaras Hindu University, Varanasi 221005 (India); Mishra, Kavita [Department of Physics, University of Lucknow, Lucknow 226007 (India)

    2016-07-28

    Dual-mode luminescence (downshifting-DS and upconversion-UC) properties of Pr{sup 3+}/Yb{sup 3+} co-doped Y{sub 1−x}Gd{sub x}NbO{sub 4} (x = 0.0, 0.5, and 1.0) phosphors synthesized by solid state reaction technique have been explored with and without Gd{sup 3+} ion. The structural characterizations (XRD, SEM, and FTIR) confirm the pure phase of YNbO{sub 4} phosphor. Further, with the Gd{sup 3+} ion co-doping, the YNbO{sub 4} phosphors having a random shape and the large particle size are found to be transformed into nearly spherical shape particles with the reduced particle size. The optical band gaps (E{sub g}) of Y{sub 1−x}Gd{sub x}NbO{sub 4} (x = 0.00, 0.25, 0.50, and 1.00) calculated from UV-Vis-NIR measurements are ∼3.69, 4.00, 4.38, and 4.44 eV, respectively. Moreover, YNbO{sub 4} phosphor is a promising blue emitting material, whereas Y{sub 1−x−y−z}Pr{sub y}Yb{sub z}Gd{sub x}NbO{sub 4} phosphor gives intense green, blue, and red emissions via dual-mode optical processes. The broad blue emission arises due to (NbO{sub 4}){sup 3−} group of the host with λ{sub ex} = 264 nm, whereas Pr{sup 3+} doped YNbO{sub 4} phosphor gives dominant red and blue emissions along with comparatively weak green emission on excitation with λ{sub ex} = 300 nm and 491 nm. The concentration dependent variation in emission intensity at 491 nm ({sup 3}P{sub 0}→{sup 3}H{sub 4} transition) and 612 nm ({sup 1}D{sub 2}→{sup 3}H{sub 4} transition); at 612 nm ({sup 1}D{sub 2}→{sup 3}H{sub 4} transition) and 658 nm ({sup 3}P{sub 0}→{sup 3}F{sub 2} transition) of Pr{sup 3+} ion in YNbO{sub 4} phosphor with λ{sub ex} = 300 nm and 491 nm excitations, respectively, has been thoroughly explored and explained by the cross-relaxation process through different channels. The sensitization effect of Bi{sup 3+} ion co-doping on DS properties of the phosphor has also been studied. The observed DS results have been optimized by varying the

  16. Transportin-1-dependent YB-1 nuclear import

    International Nuclear Information System (INIS)

    Mordovkina, Daria A.; Kim, Ekaterina R.; Buldakov, Ilya A.; Sorokin, Alexey V.; Eliseeva, Irina A.; Lyabin, Dmitry N.; Ovchinnikov, Lev P.

    2016-01-01

    The DNA/RNA-binding protein YB-1 (Y-box binding protein 1) performs multiple functions both in the cytoplasm and the nucleus of the cell. Generally localized to the cytoplasm, under certain conditions YB-1 is translocated to the nucleus. Here we report for the first time a transport factor that mediates YB-1 nuclear import – transportin-1. The YB-1/transportin-1 complex can be isolated from HeLa cell extract. Nuclear import of YB-1 and its truncated form YB-1 (1-219) in in vitro transport assay was diminished in the presence of a competitor substrate and ceased in the presence of transportin-1 inhibitor M9M. Inhibitors of importin β1 had no effect on YB-1 transport. Furthermore, transport of YB-1 (P201A/Y202A) and YB-1 (1–219) (P201A/Y202A) bearing inactivating mutations in the transportin-1-dependent nuclear localization signal was practically abolished. Together, these results indicate that transportin-1 mediates YB-1 nuclear translocation. - Highlights: • Transportin-1 mediates YB-1 nuclear import. • YB-1 nuclear translocation is diminished in the presence of transportin-1 inhibitors. • Mutations in the PY motif of YB-1 NLS prevent its translocation to the nucleus.

  17. Up-conversion luminescent properties of La{sub (0.80−x)}VO{sub 4}:Yb{sub x}, Er{sub 0.20} phosphors

    Energy Technology Data Exchange (ETDEWEB)

    Choi, Dong Hwa; Kang, Deok Hwa [Department of Materials Science and Engineering, Silla University, Busan 617-736 (Korea, Republic of); Yi, Soung Soo, E-mail: ssyi@silla.ac.kr [Department of Materials Science and Engineering, Silla University, Busan 617-736 (Korea, Republic of); Jang, Kiwan [Department of Physics, Changwon National University, Changwon 641-773 (Korea, Republic of); Jeong, Jung Hyun [Department of Physics, Pukyong National University, Busan 608-737 (Korea, Republic of)

    2015-11-15

    Highlights: • A novel green and red emitting LaVO{sub 4}:Yb{sub x}{sup 3+}, Er{sub 0.20}{sup 3+} phosphors were synthesized. • Their structures, luminescent properties have also been investigated. • Major laser transition for Er{sup 3+} ion is {sup 2}H{sub 11/2} → {sup 4}I{sub 15/2} (525 nm). • These results suggest the possibility as photonic devices. - Abstract: Yb{sup 3+}, Er{sup 3+} co-doped LaVO{sub 4} phosphors were synthesized by solid state reaction method. Yb{sup 3+} concentrations were changed from 0.01 to 0.20 mol for the fixed Er{sup 3+} concentration at 0.2 mol. The crystalline structure of samples was investigated by X-ray diffraction (XRD). The composition was investigated by X-ray photoelectron spectroscopy (XPS) analysis. The surface morphology was observed by scanning electron microscope (SEM). The red and green up-conversion emissions were observed in Yb{sup 3+}, Er{sup 3+} co-doped LaVO{sub 4} phosphors under the excitation of 980 nm laser diode. Several emissions in green and red regions of the spectrum were observed near 525 nm, 553 nm and 659 nm radiated by {sup 2}H{sub 11/2} → {sup 4}I{sub 15/2}, {sup 4}S{sub 3/2} → {sup 4}I{sub 15/2}, and {sup 4}F{sub 3/2} → {sup 4}I{sub 15/2} transitions, respectively.

  18. Magnetic anisotropy of pure and doped YbInCu sub 4 compounds at ambient and high pressures

    CERN Document Server

    Mushnikov, N V; Rozenfeld, E V; Yoshimura, K; Zhang, W; Yamada, M; Kageyama, H

    2003-01-01

    The susceptibility and high-field magnetization of single-crystalline Yb sub 1 sub - sub x Y sub x InCu sub 4 (x = 0, 0.2 and 0.3) samples have been measured for different field orientations at ambient and high pressures. The compounds with x = 0 and 0.2 undergo a first-order valence transition from the intermediate-valence state to the trivalent state on increasing either temperature or magnetic field. The magnetization and susceptibility of these compounds have appreciable anisotropy in both states. The magnetic phase diagram of Yb sub 1 sub - sub x Y sub x InCu sub 4 determined at ambient pressure is also anisotropic, which is explained by the crystal-field calculations for the free Yb ion in the high-temperature phase. Moreover, the low-temperature magnetization process for x = 0.2 and 0.3 has been measured in low fields under high pressure; it shows anisotropic ferromagnetic ordering.

  19. Quantum sized Ag nanocluster assisted fluorescence enhancement in Tm3+-Yb3+ doped optical fiber beyond plasmonics

    International Nuclear Information System (INIS)

    Chattopadhyay, Rik; Haldar, Arindam; Paul, Mukul C.; Das, Shyamal; Bhadra, Shyamal K.

    2015-01-01

    We report a process for enhancing fluorescence emission from conventional rare earth ions in optical fiber by metal nanocluster (MNC) in nonresonant indirect pumping. The process is completely different from formal metal enhanced fluorescence phenomenon as the MNCs are too small in size to support localized surface plasmon and the excitation wavelength is far from plasmon resonance frequency. We used an established theory of two coupled oscillators to explain the simultaneous enhancement of Ytterbium (Yb 3+ ) and Thulium (Tm 3+ ) emission by silver (Ag) NCs under nonresonant pumping in optical fiber. The fiber is pumped with a 980 nm fiber pigtailed laser diode with input power of 20–100 mW to excite the Yb 3+ . Four times enhancement of Yb 3+ emission of 900–1100 nm and Tm 3+ upconversion emission around 474 nm, 650 nm, and 790 nm is observed in the fiber with Ag NCs

  20. Linearly polarized intracavity passive Q-switched Yb-doped ...

    Indian Academy of Sciences (India)

    2014-02-14

    Feb 14, 2014 ... ytterbium-doped photonic crystal fibre laser with a Cr4+:YAG crystal ... average output power of 9.4 W with pulse duration of 64 ns and ... applications of nonlinear frequency shifting like frequency doubling and optical paramet-.

  1. Guiding and amplification properties of rod-type photonic crystal fibers with sectioned core doping

    Science.gov (United States)

    Selleri, S.; Poli, F.; Passaro, D.; Cucinotta, A.; Lægsgaard, J.; Broeng, J.

    2009-05-01

    Rod-type photonic crystal fibers are large mode area double-cladding fibers with an outer diameter of few millimeters which can provide important advantages for high-power lasers and amplifiers. Numerical studies have recently demonstrated the guidance of higher-order modes in these fibers, which can worsen the output beam quality of lasers and amplifiers. In the present analysis a sectioned core doping has been proposed for Ybdoped rod-type photonic crystal fibers, with the aim to improve the higher-order mode suppression. A full-vector modal solver based on the finite element method has been applied to properly design the low refractive index ring in the fiber core, which can provide an increase of the differential overlap between the fundamental and the higher-order mode. Then, the gain competition among the guided modes along the Yb-doped rod-type fibers has been investigated with a spatial and spectral amplifier model. Simulation results have shown the effectiveness of the sectioned core doping in worsening the higher-order mode overlap on the doped area, thus providing an effective single-mode behavior of the Yb-doped rod-type photonic crystal fibers.

  2. Spectral-converting study of La{sub 1−m−n}Er{sub m}Yb{sub n}OCl (m=0.001–0.2, n=0–0.1) phosphors

    Energy Technology Data Exchange (ETDEWEB)

    Park, Sangmoon, E-mail: spark@silla.ac.kr [Center for Green Fusion Technology and Department of Engineering in Energy and Applied Chemistry, Silla University, Busan 617-736 (Korea, Republic of); Cho, So-Hye [Center for Materials Architecturing, Institute of Multidisciplinary Convergence of Materials, Korea Institute of Science and Technology, Seoul 130-650 (Korea, Republic of)

    2014-09-15

    Optical materials composed of La{sub 1−m−n}Er{sub m}Yb{sub n}OCl (m=0.001–0.2, n=0–0.1) solid solution were prepared via a solid-state reaction using excess NH{sub 4}Cl flux at 950 °C for 30 min. X-ray diffraction patterns of La{sub 1−m}Er{sub m}OCl were compared upon altering the molar ratios of the flux to the La{sup 3+} (Er{sup 3+}, Yb{sup 3+}) ions. By means of photoluminescence spectra, the dependence of the luminescence intensity as a function of the Er{sup 3+} content and the color CIE coordinates of the Er{sup 3+}-doped layered LaOCl compounds were also investigated under excitation by near-ultraviolet (NUV) and visible light. The spectral conversion properties of Er{sup 3+} and Er{sup 3+}–Yb{sup 3+} ions doped into LaOCl phosphors were elucidated under diode-laser irradiation of 980 nm in wavelength. The desired up-conversion of the emitting light, passing throughout the green, orange, and red regions of the spectrum, was achieved by appropriate Er{sup 3+} and/or Yb{sup 3+} concentrations in the LaOCl host structure under 980-nm-excitation light, while its mechanism in the phosphors was described by an energy-level schematic. Up-conversion emission spectra and the dependence of the emission intensity on pump power in the La{sub 0.89}Er{sub 0.1}Yb{sub 0.01}OCl phosphor were investigated under diode-laser irradiation of both wavelengths, 980 and 1550 nm. - Highlights: • Flux-assisted La{sub 1−m−n}Er{sub m}Yb{sub n}OCl (m=0.001–0.2, n=0–0.1) phosphors were prepared. • Distinctive photoluminescence properties of Er{sup 3+}-doped LaOCl were investigated. • Spectral converting properties of Er{sup 3+} and Yb{sup 3+} in LaOCl phosphors were elucidated. • Up-conversion mechanisms are proposed on the basis of an energy-level diagram. • Dependence of the emission intensity on pump power in the phosphor was investigated.

  3. Kondo effect and heavy fermions in Yb compounds

    International Nuclear Information System (INIS)

    Bonville, P.

    1987-01-01

    The Kondo properties of Yb dilute alloys and intermetallics have been investigated using Moessbauer spectroscopy on 170 Yb. In the dilute alloys AuYb and LaBe 13 Yb, the Kondo logarithmic anomaly of the impurity relaxation rate has been detected, and in the concentrated Yb compounds YbBe 13 , YbP and YbAs, and YbCuAl, the manifestations of the interplay between the Kondo effect and the magnetic ordering due to the RKKY interaction have been characterized

  4. Summary of Workshop on InP: Status and Prospects

    Science.gov (United States)

    Walters, R. J.; Weinberg, I.

    1994-01-01

    The primary objective of most of the programs in InP solar cells is the development of the most radiation hard solar cell technology. In the workshop, it was generally agreed that the goal is a cell which displays high radiation tolerance in a radiation environment equivalent to a 1 MeV electron fluence of about 10(exp 16)/sq cm. Furthermore, it is desired that the radiation response of the cell be essentially flat out to this fluence - i.e. that the power output of the cell not decrease from its beginning of life (BOL) value in this radiation environment. It was also agreed in the workshop that the manufacturability of InP solar cells needs to be improved. In particular, since InP wafers are relatively dense and brittle, alternative substrates need to be developed. Research on hetero-epitaxial InP cells grown on Si, Ge, and GaAs substrates is currently underway. The ultimate goal is to develop hetero-epitaxial InP solar cells using a cheap, strong, and lightweight substrate.

  5. Effect of F- ions on physical and spectroscopic properties of Yb3+-doped TeO2-based glasses

    International Nuclear Information System (INIS)

    Wang Guonian; Dai Shixun; Zhang Junjie; Xu Shiqing; Hu Lili; Jiang Zhonghong

    2005-01-01

    The effects of F - ions on physical and spectroscopic properties of the Yb 3+ in tellurite glass system are investigated. The results show that the glass system takes on good thermal stability with the content of ZnF 2 lower than 15 mol%, both the emission cross-section and the fluorescence lifetime of Yb 3+ ions increase evidently which indicate that such oxyfluoride tellurite glass system is a promising laser host matrix for high power generation. FT-IR spectra were used to analyze the effect of F- ions on the structure of tellurite glasses and OH - groups in this glass system. Analysis demonstrates that addition of fluoride decreases the symmetry of the structure of tellurite glasses which increases the emission cross-section and removes the OH - groups, and which improves the measured fluorescence lifetime of Yb 3+ ions

  6. Color tunability in green, red and infra-red upconversion emission in Tm{sup 3+}/Yb{sup 3+}/Ho{sup 3+} co-doped CeO{sub 2} with potential application for improvement of efficiency in solar cells

    Energy Technology Data Exchange (ETDEWEB)

    Carvalho, Luiz G.A.; Rocha, Leonardo A.; Buarque, Juliana M.M. [Laboratório de Materiais Inorgânicos Fotoluminescentes e Polímeros Biodegradáveis (LAFOP), Grupo de Pesquisa em Química de Materiais – (GPQM), Departamento de Ciências Naturais, Universidade Federal de São João Del Rei, Campus Dom Bosco, Praça Dom Helvécio, 74, 36301-160 São João Del Rei, MG (Brazil); Gonçalves, Rogéria Rocha [Departamento de Química, Faculdade de Filosofia, Ciências e Letras de Ribeirão Preto, USP, Av. Bandeirantes, 3900, 14040-901 Ribeirão Preto, SP (Brazil); Nascimento Jr, Clébio S. [Laboratório de Química Teórica e Computacional – (LQTC), Departamento de Ciências Naturais, Universidade Federal de São João del-Rei, Campus Dom Bosco, Praça Dom Helvécio, 74, 36301-160 São João del-Rei, MG (Brazil); and others

    2015-03-15

    The preparation of Tm{sup 3+}/Yb{sup 3+}/Ho{sup 3+} co-doped CeO{sub 2} prepared by the precipitation method using ammonium hydroxide as a precursor is presented. By X-ray diffraction the materials show the phase-type of fluorite structure and the crystallite sizes were calculated by the Scherrer's equation. No other phase was observed evincing that the rare earth ions were inserted into the fluorite phase as substitutional or interstitial dopants. The microstrain calculated by the Williamson–Hall method do not show significant changes in their values, indicating that the inclusion of rare earths does not causes structural changes in the CeO{sub 2} used as a host matrix. All material showed intense upconversion emission at red and green region under excitation with diode laser at 980 nm. The color of emission changes from green to red with increasing excitation power pump. The materials showed suitable photoluminescent properties for applications as a laser source, solar cells, and great emitter at 800 nm. - Highlights: • Tm{sup 3+}/Yb{sup 3+}/Ho{sup 3+} co-doped CeO{sub 2} prepared by the simple way. • Intense upconversion emission regions and the tunability of emission color by the laser power pump. • The materials showed suitable photoluminescent properties for different applications.

  7. Study by AES, EELS Spectroscopy of electron Irradiation on InP and InPO4/InP in comparison with Monte Carlo simulation

    International Nuclear Information System (INIS)

    Lounis, Z; Bouslama, M; Hamaida, K; Abdellaoui, A; Ouerdane, A; Ghaffour, M; Berrouachedi, N; Jardin, C

    2012-01-01

    We give the great interest to characterise the InP and InPO 4 /InP submitted to electron beam irradiation owing to the Auger Electron Spectroscopy (AES) associated to both methods Electron Energy Loss Spectroscopy (EELS). The incident electron produces breaking of (In-P) chemical bonds. The electron beam even acts to stimulate oxidation of InP surface involving on the top layers. Other, the oxide InPO 4 developed on InP does appear very sensitive to the irradiation due to electron beam shown by the monitoring of EELS spectra recorded versus the irradiated times of the surface. There appears a new oxide thought to be In 2 O 3 . We give the simulation methods Casino (Carlo simulation of electron trajectory in solids) for determination with accuracy the loss energy of backscattered electrons and compared with reports results have been obtained with EELS Spectroscopy. These techniques of spectroscopy alone do not be able to verify the affected depth during interaction process. So, using this simulation method, we determine the interaction of electrons in the matter.

  8. Luminescence of Er3+ doped double lead halide crystals under X-ray, UV, VIS and IR excitation

    Science.gov (United States)

    Serazetdinov, A. R.; Smirnov, A. A.; Pustovarov, V. A.; Isaenko, L. I.

    2017-09-01

    Er3+ doped double lead halide crystals incorporate a number of properties making them interesting for practical use in light conducting materials. X-ray excited luminescence (XRL) spectra, photoluminescence (PL) spectra in region of 1.5-3.5 eV, photoluminescence excitation (PLE) spectra (2.75-5 eV) and anti-stokes luminescence (ASL) spectra were measured at room temperature in KPb2Cl5 (KPC) and RbPb2Br5 (RPB) matrices doped with Er3+ (1%) ions and in KPC doped with Er3++ Yb3+ ions(1:3 ratio concentration). Intraconfigurational f→f transitions are observed in Er3+ ions in most of the cases. The concrete spectrum form is strongly dependent on the excitation energy. Under 980 nm excitation upper Er3+ levels are excited, showing upconversional processes. In case of 313 nm (UV) and 365 nm (VIS) excitation self trapped exciton luminescence was detected in RPB crystal. Additional Yb3+ doping ions strongly increase quantum yield under 980 nm excitation and this doping cause insignificant influence on quantum yield under VIS or UV excitation.

  9. Young's Modulus of Wurtzite and Zinc Blende InP Nanowires.

    Science.gov (United States)

    Dunaevskiy, Mikhail; Geydt, Pavel; Lähderanta, Erkki; Alekseev, Prokhor; Haggrén, Tuomas; Kakko, Joona-Pekko; Jiang, Hua; Lipsanen, Harri

    2017-06-14

    The Young's modulus of thin conical InP nanowires with either wurtzite or mixed "zinc blende/wurtzite" structures was measured. It has been shown that the value of Young's modulus obtained for wurtzite InP nanowires (E [0001] = 130 ± 30 GPa) was similar to the theoretically predicted value for the wurtzite InP material (E [0001] = 120 ± 10 GPa). The Young's modulus of mixed "zinc blende/wurtzite" InP nanowires (E [111] = 65 ± 10 GPa) appeared to be 40% less than the theoretically predicted value for the zinc blende InP material (E [111] = 110 GPa). An advanced method for measuring the Young's modulus of thin and flexible nanostructures is proposed. It consists of measuring the flexibility (the inverse of stiffness) profiles 1/k(x) by the scanning probe microscopy with precise control of loading force in nanonewton range followed by simulations.

  10. An ellipsometric measurement of optical properties for InP surfaces

    International Nuclear Information System (INIS)

    Liu, X.; Irene, E.A.; Hattangady, S.; Fountain, G.

    1990-01-01

    Several chemical cleaning procedures for InP surfaces have been studied using ellipsometry. The strong influence of cleaning on the optical properties of InP surfaces suggests that the measurements involved the formation of surface films. In order to determine the complex index of refraction for InP, a novel method which employs ellipsometry measurements of a thin nonabsorbing film on a substrate rather than measurements of a bare surface has been explored. From the knowledge of the refractive index for a series of thicknesses of films on a substrate, the complex refractive index value for the substrate can be determined. Plasma enhanced chemical vapor deposition (PECVD) SiO 2 and Si 3 N 4 films on InP have been used for this experiment, and the complex refractive index for InP has been determined to be 3.521 + i0.300 at the wavelength of 632.8 nm

  11. Near infrared emission of TbAG:Ce{sup 3+},Yb{sup 3+} phosphor for solar cell applications

    Energy Technology Data Exchange (ETDEWEB)

    Meshram, N. D., E-mail: meshramnileshsd@gmail.com [Shri. Mathuradas Mohota College of Science, Sakkardara Square, Nagpur-440009 (India); Yadav, P. J., E-mail: yadav.pooja75@yahoo.in [Department of Electronics, Nagpur University campus, Nagpur-440010 (India); Pathak, A. A., E-mail: aapathak@yahoo.com [National power Training Institute, South ambazari road, Nagpur-440022 (India); Joshi, C. P., E-mail: charusheela-4253@yahoo.co.in [Ramdeobaba College of Engineering and Management, Katol road, Gittikhadan Nagpur-440012 (India); Moharil, S. V., E-mail: svmoharil@yahoo.com [Department of Physics, Nagpur University campus, Nagpur-440010 (India)

    2016-05-06

    Luminescent materials doped with rare earth ions are used for many devices such as optical amplifiers in telecommunication, phosphors for white light emitting diodes (LEDs), displays, and so on. Recently, they also have attracted a great interest for photovoltaic applications to improve solar cell efficiency by modifying solar spectrum. Crystal silicon (c-Si) solar cells most effectively convert photons of energy close to the semiconductor band gap. The mis-match between the incident solar spectrum and the spectral response of solar cells is one of the main reasons to limit the cell efficiency. The efficiency limit of the c-Si has been estimated to be 29% by Shockley and Queisser. However, this limit is estimated to be improved up to 38.4% by modifying the solar spectrum by a quantum cutting (down converting) phosphor which converts one photon of high energy into two photons of lower energy. The phenomenon such as the quantum cutting or the down conversion of rare earth ions have been investigated since Dexter reported the possibility of a luminescent quantum yield greater than unity in 1957. In the past, the quantum cutting from a vacuum ultraviolet photon to visible photons for Pr{sup 3+}, Gd{sup 3+},Gd{sup 3+}–Eu{sup 3+}, and Er{sup 3+}–Tb{sup 3+} had been studied. Recently, a new quantum cutting phenomenon from visible photon shorter than 500 nm to two infrared photons for Tb{sup 3+}–Yb{sup 3+}, Pr{sup 3+}–Yb{sup 3+}, and Tm{sup 3+}–Yb{sup 3+} has been reported. The Yb{sup 3+} ion is suitable as an acceptor and emitter because luminescent quantum efficiency of Yb{sup 3+} is close to 100% and the energy of the only excited level of Yb{sup 3+} (1.2 eV) is roughly in accordance with the band gap of Si (1.1 eV). In addition, the Ce{sup 3+}-doped Tb{sub 3}Al{sub 5}O{sub 12} (TbAG), used as a phosphor for white LED, has broad absorption bands in the range of 300–500 nm due to strong ligand field and high luminescent quantum efficiency. Therefore, the

  12. P/N InP solar cells on Ge wafers

    Science.gov (United States)

    Wojtczuk, Steven; Vernon, Stanley; Burke, Edward A.

    1994-01-01

    Indium phosphide (InP) P-on-N one-sun solar cells were epitaxially grown using a metalorganic chemical vapor deposition process on germanium (Ge) wafers. The motivation for this work is to replace expensive InP wafers, which are fragile and must be thick and therefore heavy, with less expensive Ge wafers, which are stronger, allowing use of thinner, lighter weight wafers. An intermediate InxGs1-xP grading layer starting as In(0.49)Ga(0.51) at the GaAs-coated Ge wafer surface and ending as InP at the top of the grading layer (backside of the InP cell) was used to attempt to bend some of the threading dislocations generated by lattice-mismatch between the Ge wafer and InP cell so they would be harmlessly confined in this grading layer. The best InP/Ge cell was independently measured by NASA-Lewis with a one-sun 25 C AMO efficiently measured by NASA-Lewis with a one-circuit photocurrent 22.6 mA/sq cm. We believe this is the first published report of an InP cell grown on a Ge wafer. Why get excited over a 9 percent InP/Ge cell? If we look at the cell weight and efficiency, a 9 percent InP cell on an 8 mil Ge wafer has about the same cell power density, 118 W/kg (BOL), as the best InP cell ever made, a 19 percent InP cell on an 18 mil InP wafer, because of the lighter Ge wafer weight. As cell panel materials become lighter, the cell weight becomes more important, and the advantage of lightweight cells to the panel power density becomes more important. In addition, although InP/Ge cells have a low beginning-of-life (BOL) efficiency due to dislocation defects, the InP/Ge cells are very radiation hard (end-of-life power similar to beginning-of-life). We have irradiated an InP/Ge cell with alpha particles to an equivalent fluence of 1.6 x 10(exp 16) 1 MeV electrons/sq cm and the efficiency is still 83 percent of its BOL value. At this fluence level, the power output of these InP/Ge cells matches the GaAs/Ge cell data tabulated in the JPL handbook. Data are presented

  13. An inelastic neutron scattering study of the spin dynamics of Yb1-xLuxAl3

    International Nuclear Information System (INIS)

    Osborn, R.

    1998-01-01

    We present the results of a systematic inelastic neutron scattering study of the spin dynamics of the mixed valent compound YbAl 3 doped with nonmagnetic lutetium. The aim of the investigation is to clarify the origin of the unusual gap-like magnetic response observed in YbAl 3 , which can be modeled by two inelastic peaks: a narrow peak at 34 meV with HWHM, r = 6.4 ± 0.8 meV and a broad peak at 44 meV with Λ = 30 ± 1 meV. Lutetium substitution leads to a substantial increase in the linewidth (Λ = 9 ± 1 meV at x = 0.1) and a decrease in the intensity (down by 60% at x = 0.1) of the narrow component, with a negligible effect on the broad inelastic peak. This trend is confirmed with higher doping resulting in the complete suppression of the narrow peak at x ≥ 0.35. The results indicate that the narrow component arises from coherent excitation processes within the hybridized 4f-band, which are destroyed by disorder, while the broad component is not so sensitive to the loss of coherence

  14. Fabrication and evaluation of chitosan/NaYF4:Yb3+/Tm3+ upconversion nanoparticles composite beads based on the gelling of Pickering emulsion droplets.

    Science.gov (United States)

    Yan, Huiqiong; Chen, Xiuqiong; Shi, Jia; Shi, Zaifeng; Sun, Wei; Lin, Qiang; Wang, Xianghui; Dai, Zihao

    2017-02-01

    The rare earth ion doped upconversion nanoparticles (UCNPs) synthesized by hydrophobic organic ligands possess poor solubility and low fluorescence quantum yield in aqueous media. To conquer this issue, NaYF 4 :Yb 3+ /Tm 3+ UCNPs, synthesized by a hydrothermal method, were coated with F127 and then assembled with chitosan to fabricate the chitosan/NaYF 4 :Yb 3+ /Tm 3+ composite beads (CS/NaYF 4 :Yb 3+ /Tm 3+ CBs) by Pickering emulsion system. The characterization results revealed that the as-synthesized NaYF 4 :Yb 3+ /Tm 3+ UCNPs with an average size of 20nm exhibited spherical morphology, high crystallinity and characteristic emission upconversion fluorescence with an overall blue color output. The NaYF 4 :Yb 3+ /Tm 3+ UCNPs were successfully conjugated on the surface of chitosan beads by the gelling of emulsion droplets. The resultant CS/NaYF 4 :Yb 3+ /Tm 3+ CBs showed good upconversion luminescent property, drug-loading capacity, release performance and excellent biocompatibility, exhibiting great potentials in targeted drug delivery and tissue engineering with potential tracking capability and lasting release performance. Copyright © 2016 Elsevier B.V. All rights reserved.

  15. Growth and anisotropic transport properties of self-assembled InAs nanostructures in InP

    International Nuclear Information System (INIS)

    Bierwagen, O.

    2007-01-01

    Self-assembled InAs nanostructures in InP, comprising quantum wells, quantum wires, and quantum dots, are studied in terms of their formation and properties. In particular, the structural, optical, and anisotropic transport properties of the nanostructures are investigated. The focus is a comprehending exploration of the anisotropic in-plane transport in large ensembles of laterally coupled InAs nanostructures. The self-assembled Stranski-Krastanov growth of InAs nanostructures is studied by gas-source molecular beam epitaxy on both nominally oriented and vicinal InP(001). Optical polarization of the interband transitions arising from the nanostructure type is demonstrated by photoluminescence and transmission spectroscopy. The experimentally convenient four-contact van der Pauw Hall measurement of rectangularly shaped semiconductors, usually applied to isotropic systems, is extended to yield the anisotropic transport properties. Temperature dependent transport measurements are performed in large ensembles of laterally closely spaced nanostructures. The transport of quantum wire-, quantum dash- and quantum dot containing samples is highly anisotropic with the principal axes of conductivity aligned to the directions. The direction of higher mobility is [ anti 110], which is parallel to the direction of the quantum wires. In extreme cases, the anisotropies exceed 30 for electrons, and 100 for holes. The extreme anisotropy for holes is due to diffusive transport through extended states in the [ anti 110], and hopping transport through laterally localized states in the [110] direction, within the same sample. A novel 5-terminal electronic switching device based on gate-controlled transport anisotropy is proposed. The gate-control of the transport anisotropy in modulation-doped, self-organized InAs quantum wires embedded in InP is demonstrated. (orig.)

  16. Growth and anisotropic transport properties of self-assembled InAs nanostructures in InP

    Energy Technology Data Exchange (ETDEWEB)

    Bierwagen, O.

    2007-12-20

    Self-assembled InAs nanostructures in InP, comprising quantum wells, quantum wires, and quantum dots, are studied in terms of their formation and properties. In particular, the structural, optical, and anisotropic transport properties of the nanostructures are investigated. The focus is a comprehending exploration of the anisotropic in-plane transport in large ensembles of laterally coupled InAs nanostructures. The self-assembled Stranski-Krastanov growth of InAs nanostructures is studied by gas-source molecular beam epitaxy on both nominally oriented and vicinal InP(001). Optical polarization of the interband transitions arising from the nanostructure type is demonstrated by photoluminescence and transmission spectroscopy. The experimentally convenient four-contact van der Pauw Hall measurement of rectangularly shaped semiconductors, usually applied to isotropic systems, is extended to yield the anisotropic transport properties. Temperature dependent transport measurements are performed in large ensembles of laterally closely spaced nanostructures. The transport of quantum wire-, quantum dash- and quantum dot containing samples is highly anisotropic with the principal axes of conductivity aligned to the <110> directions. The direction of higher mobility is [ anti 110], which is parallel to the direction of the quantum wires. In extreme cases, the anisotropies exceed 30 for electrons, and 100 for holes. The extreme anisotropy for holes is due to diffusive transport through extended states in the [ anti 110], and hopping transport through laterally localized states in the [110] direction, within the same sample. A novel 5-terminal electronic switching device based on gate-controlled transport anisotropy is proposed. The gate-control of the transport anisotropy in modulation-doped, self-organized InAs quantum wires embedded in InP is demonstrated. (orig.)

  17. Characteristics of withstanding radiation damage of InP crystals and devices

    International Nuclear Information System (INIS)

    Yamaguchi, Masafumi; Ando, Koshi

    1988-01-01

    Recently, the authors discovered that the characteristics of with standing radiation damage of InP crystals and devices (solar cells) are superior to those of Si and GaAs crystals and devices. Also the restoration phenomena at room temperature of radiation deterioration and the accelerated anneal phenomena by light irradiation and the injection of other minority, carriers in InP system devices were found. Such excellent characteristics suggested that InP devices are promising for the use in space. In this paper, taking an example of solar cells, the radiation resistance characteristics and their mechanism of InP crystals and devices are reported, based on the results of analysis by deep level transient spectroscopy and others. In InP solar cells, the high efficiency of photoelectric conversion was maintained even in the high dose irradiation of 1 MeV electron beam. As the carrier concentration in InP crystals is higher, they are stronger against radiation. With the increase of carrier concentration, the rate of anneal of radiation deterioration at room temperature increased. The accelerated anneal effect by minority carrier injection was remarkable in n + -p junction cells. The excellent characteristics of InP crystals are due to the formation of Frenkel defects of P and their instability. (K.I.)

  18. Performance, Defect Behavior and Carrier Enhancement in Low Energy, Proton Irradiated p(+)nn(+) InP Solar Cells

    Science.gov (United States)

    Weinberg, I.; Rybicki, G. C.; Vargas-Aburto, C.; Jain, R. K.; Scheiman, D.

    1994-01-01

    InP p(+)nn(+) cells, processed by MOCVD, were irradiated by 0.2 MeV protons and their performance and defect behavior observed to a maximum fluence of 10(exp 13)/sq cm. Their radiation induced degradation, over this fluence range, was considerably+less than observed for similarly irradiated, diffused junction n p InP cells. Significant degradation occurred in both the cell's emitter and base regions the least degradation occurring in the depletion region. A significant increase in series resistance occurs at the highest fluenc.e. Two majority carrier defect levels, E7 and E10, are observed by DLTS with activation energies at (E(sub C) - 0.39)eV and (E(sub C) - 0.74)eV respectively. The relative concentration of these defects differs considerably from that observed after 1 MeV electron irradiation. An increased carrier concentration in the cell's n-region was observed at the highest proton fluence, the change in carrier concentration being insignificant at the lower fluences. In agreement with previous results, for 1 and 1.5 MeV electron irradiated InP p(+)n junctions, the defect level E10 is attributed to a complex between zinc, diffused into the n-region from the zinc doped emitter, and a radiation induced defect. The latter is assumed to be either a phosphorus vacancy or interstitial. The increased, or enhanced carrier concentration is attributed to this complex acting as a donor.

  19. Cooperative down-conversion of UV light in disordered scheelitelike Yb-doped NaGd(MoO4)2 and NaLa(MoO4)2 crystals

    Science.gov (United States)

    Subbotin, K. A.; Osipova, Yu. N.; Lis, D. A.; Smirnov, V. A.; Zharikov, E. V.; Shcherbakov, I. A.

    2017-07-01

    Concentration series of disordered scheelitelike Yb:NaGd(MoO4)2 and Yb:NaLa(MoO4)2 single crystals are grown by the Czochralski method. The actual concentrations of Yb3+ ions in the crystals are determined by optical-absorption spectroscopy. The luminescence of Yb3+ ions in these crystals in the region of 1 μm is studied under UV and IR excitation. In the case of UV excitation, this luminescence appears as a result of nonradiative excited state energy transfer from donor centers of unknown nature to ytterbium. The character of the concentration dependence of Yb3+ luminescence indicates that the energy transfer at high Yb concentrations occurs with active participation of a cooperative mechanism, according to which the excitation energy of one donor center is transferred simultaneously to two Yb3+ ions. In other words, the quantum yield of this transfer exceeds unity, which can be used to increase the efficiency of crystalline silicon (c-Si) solar cells.

  20. Effects of impurities on radiation damage in InP

    International Nuclear Information System (INIS)

    Yamaguchi, M.; Ando, K.

    1986-01-01

    Strong impurity effects upon introduction and annealing behavior of radiation-induced defects in InP irradiated with 1-MeV electrons have been found. The main defect center of 0.37-eV hole trap H4 in p-InP, which must be due to a point defect, is annealed even at room temperature. Its annealing rate is found to be proportional to the 2/3 power of the preirradiation carrier concentration in InP. Moreover, the density of the hole trap H5 (E/sub v/+0.52 eV) in p-InP, which must be due to a point defect--impurity complex, increases with increase in the InP carrier concentration. These results suggest that the radiation-induced defects in InP must recover through long-range diffusion mediated by impurity atoms. A model is proposed in which point defects diffuse to sinks through impurities so as to disappear or bind impurities so as to form point defect--impurity complexes. In addition to the long-range diffusion mechanism, the possibility of charge-state effects responsible for the thermal annealing of radiation-induced defects in InP is also discussed

  1. Single-crystal structure refinement of YbF{sub 2} with a remark about YbH{sub 2}

    Energy Technology Data Exchange (ETDEWEB)

    Reckeweg, Olaf; DiSalvo, Francis J. [Cornell Univ., Ithaca, NY (United States). Dept. of Chemistry and Chemical Biology

    2017-07-01

    Transparent-yellow single crystals of YbF{sub 2} were obtained as only crystalline product from the solid-state reaction of Yb and teflon designed to yield 'Yb{sub 3}C{sub 3}F{sub 2}' in addition to some amorphous black material. The first single-crystal structure determination of YbF{sub 2} (cubic space group Fm anti 3m, CaF{sub 2}-type structure, a = 559.46(16) pm; R1 = 1.2%, wR2 = 3.2%) was the starting point to compare isostructural binary fluorides MF{sub 2} and hydrides MH{sub 2} (M = Ca, Yb, Eu, Sr and Ba) exhibiting an as-yet unexplained small volume per formula unit for YbH{sub 2}.

  2. A crystal chemistry approach for high-power ytterbium doped solid-state lasers: diffusion-bonded crystals and new crystalline hosts

    International Nuclear Information System (INIS)

    Gaume, R.

    2002-11-01

    This work deals with ytterbium based crystals for high-power laser applications. In particular, we focus our interest in reducing crystal heating and its consequences during laser operation following two different ways. First, we review the specific properties of ytterbium doped solid-state lasers in order to define a figure-of-merit which gives the evaluation of laser performances, thermo-mechanical and thermo-optical properties. Bearing in mind this analysis, we propose a set of theoretical tools, based on the crystallographic structure of the crystal and its chemical composition, to predict thermo-mechanical and optical potentials. This approach, used for the seek of new Yb 3+ -doped materials for high-power laser applications, shows that simple oxides containing rare-earths are favorable. Therefore, the spectroscopic properties of six new materials Yb 3+ :GdVO 4 , Yb 3+ :GdAlO 3 , Yb 3+ :Gd 2 O 3 , Yb 3+ :Sc 2 SiO 5 , Yb 3+ :CaSc 2 O 4 and Yb 3+ :SrSc 2 O 4 are described. The second aspect developed in this work deals with thermal properties enhancement of already well characterized laser materials. Two different ways are explored: a) elaboration by diffusion bonding of end-caps lasers with undoped crystals (composite crystals). Thus, different composites were obtained and a fairly lowering of thermal lensing effect was observed during laser operation. b) strengthening of crystalline structures by ionic substitution of one of its constituents. We demonstrate how crystal growth ability can be improved by a cationic substitution in the case of Yb 3+ :BOYS, a largely-tunable laser material which is of great interest for femtosecond pulses generation. (author)

  3. Wurtzite InP nanowire arrays grown by selective area MOCVD

    International Nuclear Information System (INIS)

    Chu, Hyung-Joon; Stewart, Lawrence; Yeh, Ting-Wei; Dapkus, P.D.

    2010-01-01

    InP nanowires are a unique material phase because this normally zincblende material forms in the wurtzite crystal structure below a critical diameter owing to the contribution of sidewalls to the total formation energy. This may allow control of the carrier transport and optical properties of InP nanowires for applications such as nano scale transistors, lasers and detectors. In this work, we describe the fabrication of InP nanowire arrays by selective area growth using MOCVD in the diameter range where the wurtzite structure is formed. The spatial growth rate in selective area growth is modeled by a diffusion model for the precursors. The proposed model achieves an average error of 9%. Electron microscopy shows that the grown InP nanowires are in the wurtzite crystal phase with many stacking faults. The threshold diameter of the crystal phase transition of InP nanowires is larger than the thermodynamic estimation. In order to explain this tendency, we propose a surface kinetics model based on a 2 x 2 reconstruction. This model can explain the increased tendency for wurtzite nanowire formation on InP (111)A substrates and the preferred growth direction of binary III-V compound semiconductor nanowires. (copyright 2010 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

  4. Tunable absorption resonances in the ultraviolet for InP nanowire arrays.

    Science.gov (United States)

    Aghaeipour, Mahtab; Anttu, Nicklas; Nylund, Gustav; Samuelson, Lars; Lehmann, Sebastian; Pistol, Mats-Erik

    2014-11-17

    The ability to tune the photon absorptance spectrum is an attracting way of tailoring the response of devices like photodetectors and solar cells. Here, we measure the reflectance spectra of InP substrates patterned with arrays of vertically standing InP nanowires. Using the reflectance spectra, we calculate and analyze the corresponding absorptance spectra of the nanowires. We show that we can tune absorption resonances for the nanowire arrays into the ultraviolet by decreasing the diameter of the nanowires. When we compare our measurements with electromagnetic modeling, we generally find good agreement. Interestingly, the remaining differences between modeled and measured spectra are attributed to a crystal-phase dependence in the refractive index of InP. Specifically, we find indication of significant differences in the refractive index between the modeled zinc-blende InP nanowires and the measured wurtzite InP nanowires in the ultraviolet. We believe that such crystal-phase dependent differences in the refractive index affect the possibility to excite optical resonances in the large wavelength range of 345 InP nanowire-based solar cells and photodetectors.

  5. Characterization of semi-insulating materials by photoinduced current transient spectroscopy: Fe doped INP for micro-optoelectronics and CdZnTe for nuclear detection

    International Nuclear Information System (INIS)

    Cherkaoui, K.

    1998-01-01

    The need of semi-insulating materials, of great quality, concerns various application domains. For instance, the very resistive substrates InP and CdZnTe are respectively adapted to the micro-optoelectronic circuits and to nuclear detectors. These two materials have been characterized by the thermal photoinduced current transient spectroscopy. The first part of this thesis is the defects analysis of annealing InP substrates, to understand the compensation process of this material. Two activation energy levels around 0,2 to 0,4 eV resulting from the thermal treatment have been detected. The iron omnipresence in the substrates, even undoped, has been noticed. It is then necessary to take into account the iron presence to understand the compensation process in these InP annealing substrates. the second part presents the study of the CdZnTe material, elaborated by the Bridgman method, to emphasize the defects leading to the decrease of the detector performances. The presence of three deep levels, near the forbidden band middle, is in relation with the detectors performances. (A.L.B.)

  6. Near infrared emission and multicolor tunability of enhanced upconversion emission from Er{sup 3+}–Yb{sup 3+} co-doped Nb{sub 2}O{sub 5} nanocrystals embedded in silica-based nanocomposite and planar waveguides for photonics

    Energy Technology Data Exchange (ETDEWEB)

    Aquino, Felipe Thomaz [Departamento de Química, Faculdade de Filosofia, Ciências e Letras de Ribeirão Preto, Universidade de São Paulo. Av. Bandeirantes, 3900, CEP 14040-901 Ribeirão Preto, SP (Brazil); Ferrari, Jefferson Luis [Departamento de Química, Faculdade de Filosofia, Ciências e Letras de Ribeirão Preto, Universidade de São Paulo. Av. Bandeirantes, 3900, CEP 14040-901 Ribeirão Preto, SP (Brazil); Grupo de Pesquisa em Química de Materiais – (GPQM), Departamento de Ciências Naturais, Universidade Federal de São João Del Rei, Campus Dom Bosco, Praça Dom Helvécio, 74, 36301-160 São João Del Rei, MG (Brazil); Maia, Lauro June Queiroz [Grupo Física de Materiais, Instituto de Física, Universidade Federal de Goiás, Campus II, C.P. 131, CEP 74001-970, Goiânia, GO (Brazil); Ribeiro, Sidney José Lima [Institute of Chemistry- São Paulo State University- UNESP, Araraquara, SP 14800-900 (Brazil); Ferrier, Alban [PSL Research University, Chimie ParisTech - CNRS, Institut de Recherche de Chimie Paris, 75005 Paris (France); Sorbonne Universités, UPMC Univ Paris 06, 75005 Paris (France); and others

    2016-02-15

    This work reports on the Yb{sup 3+} ion addition effect on the near infrared emission and infrared-to-visible up conversion from planar waveguides based on Er{sup 3+}–Yb{sup 3+} co-doped Nb{sub 2}O{sub 5} nanocrystals embedded in SiO{sub 2}-based nanocomposite prepared by a sol–gel process with controlled crystallization in situ. Planar waveguides and xerogels containing Si/Nb molar ratio of 90:10 up to 50:50 were prepared. Spherical-like orthorhombic or monoclinic Nb{sub 2}O{sub 5} nanocrystals were grown in the amorphous SiO{sub 2}-based host depending on the niobium content and annealing temperature, resulting in transparent glass ceramics. Crystallization process was intensely affected by rare earth content increase. Enhancement and broadening of the NIR emission has been achieved depending on the rare earth content, niobium content and annealing temperature. Effective Yb{sup 3+}→Er{sup 3+} energy transfer and a high-intensity broad band emission in the near infrared region assigned to the Er{sup 3+} ions {sup 4}I{sub 13/2}→{sup 4}I{sub 15/2} transition, and longer {sup 4}I{sub 13/2} lifetimes were observed for samples containing orthorhombic Nb{sub 2}O{sub 5} nanocrystals. Intense green and red emissions were registered for all Er{sup 3+}–Yb{sup 3+} co-doped waveguides under 980 nm excitation, assigned to {sup 2}H{sub 11/2}→{sup 4}I{sub 15/2} (525 nm),{sup 4}S{sub 3/2}→{sup 4}I{sub 15/2} (545nm) and {sup 4}F{sub 9/2}→{sup 4}I{sub 15/2} (670 nm) transitions, respectively. Different relative green and red intensities emissions were observed, depending upon niobium oxide content and the laser power. Upconversion dynamics were determined by the photons number, evidencing that ESA or ETU mechanisms are probably occurring. The 1931 CIE chromaticity diagrams indicated interesting color tunability based on the waveguides composition and pump power. The nanocomposite waveguides are promising materials for photonic applications as optical amplifiers and

  7. Three-Stage InP Submillimeter-Wave MMIC Amplifier

    Science.gov (United States)

    Pukala, David; Samoska, Lorene; Man, King; Gaier, Todd; Deal, William; Lai, Richard; Mei, Gerry; Makishi, Stella

    2008-01-01

    A submillimeter-wave monolithic integrated- circuit (S-MMIC) amplifier has been designed and fabricated using an indium phosphide (InP) 35-nm gate-length high electron mobility transistor (HEMT) device, developed at Northrop Grumman Corporation. The HEMT device employs two fingers each 15 micrometers wide. The HEMT wafers are grown by molecular beam epitaxy (MBE) and make use of a pseudomorphic In0.75Ga0.25As channel, a silicon delta-doping layer as the electron supply, an In0.52Al0.48As buffer layer, and an InP substrate. The three-stage design uses coplanar waveguide topology with a very narrow ground-to-ground spacing of 14 micrometers. Quarter-wave matching transmission lines, on-chip metal-insulator-metal shunt capacitors, series thin-film resistors, and matching stubs were used in the design. Series resistors in the shunt branch arm provide the basic circuit stabilization. The S-MMIC amplifier was measured for S-parameters and found to be centered at 320 GHz with 13-15-dB gain from 300-345 GHz. This chip was developed as part of the DARPA Submillimeter Wave Imaging Focal Plane Technology (SWIFT) program (see figure). Submillimeter-wave amplifiers could enable more sensitive receivers for earth science, planetary remote sensing, and astrophysics telescopes, particularly in radio astronomy, both from the ground and in space. A small atmospheric window at 340 GHz exists and could enable ground-based observations. However, the submillimeter-wave regime (above 300 GHz) is best used for space telescopes as Earth s atmosphere attenuates most of the signal through water and oxygen absorption. Future radio telescopes could make use of S-MMIC amplifiers for wideband, low noise, instantaneous frequency coverage, particularly in the case of heterodyne array receivers.

  8. Study of ytterbium doping effects on structural, mechanical and opto-thermal properties of sprayed ZnO thin films using the Boubaker Polynomials Expansion Scheme (BPES)

    Energy Technology Data Exchange (ETDEWEB)

    Amlouk, A. [Unite de physique des dispositifs a semi-conducteurs, Faculte des sciences de Tunis, Universite de Tunis El Manar, 2092 Tunis (Tunisia); Boubaker, K., E-mail: mmbb11112000@yahoo.f [Unite de physique des dispositifs a semi-conducteurs, Faculte des sciences de Tunis, Universite de Tunis El Manar, 2092 Tunis (Tunisia); Amlouk, M. [Unite de physique des dispositifs a semi-conducteurs, Faculte des sciences de Tunis, Universite de Tunis El Manar, 2092 Tunis (Tunisia); Bouhafs, M. [Unite de Recherche MA2I, Ecole Nationale d' Ingenieurs de Tunis, B.P. 37 Le Belvedere, 1002 Tunis (Tunisia)

    2009-10-19

    In this work, ZnO thin films have been grown on glass substrates by using a solution of propanol (C{sub 3}H{sub 8}O), water (H{sub 2}O) and zinc acetate (Z{sub n}(CH{sub 3}CO{sub 2}){sub 2}) in acidified medium (pH 5). The obtained films were n doped with ytterbium (Yb) at the rates of 100, 200 and 300 ppm. The structural features of the doped films were investigated using XRD, atomic force microscopy and scanning electronic microscopy techniques. XRD analysis shows a strong (0 0 2) X-ray diffraction line for increasing Yb-doping amounts. This c-axis preferential orientation of ZnO crystallites is naturally required to use this oxide as transparent conductor in optoelectronic applications. Atomic force microscopy (AFM) analysis shows an enhancement in the surface roughness of the doped ZnO:Yb thin films. Optical measurements were performed in 300-1800 nm domain via transmittance T(lambda) and reflectance R(lambda) spectra. Conjoint optical and thermal properties were deduced from the optical measurements in reference to the Amlouk-Boubaker opto-thermal expansivity psi{sub AB}. Optically relevant ytterbium doping effects have been discussed. Finally, mechanical measurements have been carried out using Vickers standard disposal. The results confirmed the structural and functional changes that several recent studies attributed to ytterbium doping.

  9. Graphene enhanced field emission from InP nanocrystals.

    Science.gov (United States)

    Iemmo, L; Di Bartolomeo, A; Giubileo, F; Luongo, G; Passacantando, M; Niu, G; Hatami, F; Skibitzki, O; Schroeder, T

    2017-12-08

    We report the observation of field emission (FE) from InP nanocrystals (NCs) epitaxially grown on an array of p-Si nanotips. We prove that FE can be enhanced by covering the InP NCs with graphene. The measurements are performed inside a scanning electron microscope chamber with a nano-controlled W-thread used as an anode. We analyze the FE by Fowler-Nordheim theory and find that the field enhancement factor increases monotonically with the spacing between the anode and the cathode. We also show that InP/p-Si junction has a rectifying behavior, while graphene on InP creates an ohmic contact. Understanding the fundamentals of such nanojunctions is key for applications in nanoelectronics.

  10. Ho3+/Yb3+ co-doped TeO2-BaF2-Y2O3 glasses for ∼1.2 μm laser applications

    Science.gov (United States)

    Wang, Shunbin; Li, Chengzhi; Yao, Chuanfei; Jia, Shijie; Jia, Zhixu; Qin, Guanshi; Qin, Weiping

    2017-02-01

    Intense ∼1.2 μm fluorescence is observed in Ho3+/Yb3+ co-doped TeO2-BaF2-Y2O3 glasses under 915 nm laser diode excitation. The 1.2 μm emission can be ascribed to the transition 5I6→5I8 of Ho3+. With the introducing of BaF2, the content of OH in the glasses drops markedly, and the 1.2 μm emission intensity increases gradually as increasing the concentration percentage of BaF2. Furthermore, microstructured fibers based on the TeO2-BaF2-Y2O3 glasses are fabricated by using a rod-in-tube method, and a relative positive gain of ∼9.42 dB at 1175.3 nm is obtained in a 5 cm long fiber.

  11. Formation of Deep Electron Trap by Yb3+ Codoping Leads into Super-Long Persistent Luminescence in Ce3+-doped Yttrium Aluminum Gallium Garnet Phosphors.

    Science.gov (United States)

    Ueda, Jumpei; Miyano, Shun; Tanabe, Setsuhisa

    2018-05-23

    The Y 3 Al 2 Ga 3 O 12 :Ce 3+ -Cr 3+ compound is one of the brightest persistent phosphors, but its persistent luminescence (PersL) duration is not so long due to the relatively shallow Cr 3+ electron trap. Comparing the vacuum referred binding energy of the electron trapping state by Cr 3+ and those by lanthanide ions, we selected Yb 3+ as a deeper electron trapping center. The Y 3 Al 2 Ga 3 O 12 :Ce 3+ -Yb 3+ phosphors show Ce 3+ :5d→4f green persistent luminescence after ceasing blue light excitation. The formation of Yb 2+ was confirmed by the increased intensity of absorption at 585 nm during the charging process. This result indicates that the Yb 3+ ions act as electron traps by capturing an electron. From the thermoluminescence glow curves, it was found the Yb 3+ trap makes much deeper electron trap with 1.01 eV depth than the Cr 3+ electron trap with 0.81 eV depth. This deeper Yb 3+ trap provides much slower detrapping rate of filled electron traps than the Cr 3+ -codoped persistent phosphor. In addition, by preparing transparent ceramics and optimizing Ce 3+ and Yb 3+ concentrations, the Y 3 Al 2 Ga 3 O 12 :Ce 3+ (0.2%)-Yb 3+ (0.1%) as-made transparent ceramic phosphor showed super long persistent luminescence for over 138.8 hours after ceasing blue light charging.

  12. Lanthanide-doped Sr2YF7 nanoparticles: controlled synthesis, optical spectroscopy and biodetection

    Science.gov (United States)

    Yang, Yuhan; Tu, Datao; Zheng, Wei; Liu, Yongsheng; Huang, Ping; Ma, En; Li, Renfu; Chen, Xueyuan

    2014-09-01

    Sr2YF7, as an important matrix for trivalent lanthanide (Ln3+) ions to fabricate upconversion (UC) or downshifting (DS) phosphors, has been rarely reported. Herein, monodisperse and size-controllable tetragonal-phase Ln3+-doped Sr2YF7 nanoparticles (NPs) were synthesized via a facile thermal decomposition method. Upon excitation at 980 nm, UC luminescence properties of Sr2YF7:Ln3+/Yb3+ (Ln = Tm, Er) NPs were systematically surveyed. Particularly, after coating an inert Sr2YF7 shell, the UC luminescence intensities of Sr2YF7:Tm3+/Yb3+ and Sr2YF7:Er3+/Yb3+ NPs were enhanced by ~22 and 4 times, respectively. Furthermore, intense multicolor DS luminescence was also achieved in Ce3+/Tb3+ or Eu3+ doped Sr2YF7 NPs, with absolute quantum yields of 55.1% (Tb3+) and 11.2% (Eu3+). The luminescence lifetimes of 5D4 (Tb3+) and 5D0 (Eu3+) were determined to be 3.7 and 8.1 ms, respectively. By utilizing the long-lived luminescence of Ln3+ in these Sr2YF7 NPs, we demonstrated their application as sensitive heterogeneous time-resolved photoluminescence bioprobes to detect the protein of avidin and the tumor marker of the carcinoembryonic antigen (CEA) with their limits of detection down to 40.6 and 94.9 pM, and thus reveal the great potential of these Sr2YF7:Ln3+ nanoprobes in cancer diagnosis.Sr2YF7, as an important matrix for trivalent lanthanide (Ln3+) ions to fabricate upconversion (UC) or downshifting (DS) phosphors, has been rarely reported. Herein, monodisperse and size-controllable tetragonal-phase Ln3+-doped Sr2YF7 nanoparticles (NPs) were synthesized via a facile thermal decomposition method. Upon excitation at 980 nm, UC luminescence properties of Sr2YF7:Ln3+/Yb3+ (Ln = Tm, Er) NPs were systematically surveyed. Particularly, after coating an inert Sr2YF7 shell, the UC luminescence intensities of Sr2YF7:Tm3+/Yb3+ and Sr2YF7:Er3+/Yb3+ NPs were enhanced by ~22 and 4 times, respectively. Furthermore, intense multicolor DS luminescence was also achieved in Ce3+/Tb3+ or Eu3

  13. Diode-pumped laser with Yb:YAG single-crystal fiber grown by the micro-pulling down technique

    Science.gov (United States)

    Sangla, D.; Aubry, N.; Didierjean, J.; Perrodin, D.; Balembois, F.; Lebbou, K.; Brenier, A.; Georges, P.; Tillement, O.; Fourmigué, J.-M.

    2009-02-01

    Laser emission obtained from an Yb:YAG single-crystal fiber directly grown by the micro-pulling down technique is demonstrated for the first time. We achieved 11.2 W of continuous wave (CW) output power at 1031 nm for 55 W of incident pump power at 940 nm. In the Q-switched regime, we obtained pulses as short as 17 ns, for an average power of 2.3 W at 2 kHz corresponding to an energy of 1.15 mJ. In both cases, the M 2 factor was 2.5. This single-crystal fiber showed performance similar to a standard rod elaborated by the Czochralski method. The potential of Yb3+-doped single-crystal fibers is presented for scalable high-average and high-peak-power laser systems.

  14. Long-Term INP Measurements within the BACCHUS project

    Science.gov (United States)

    Schrod, Jann; Bingemer, Heinz; Curtius, Joachim

    2016-04-01

    The European research project BACCHUS (Impact of Biogenic versus Anthropogenic emissions on Clouds and Climate: towards a Holistic UnderStanding) studies the interactions between aerosols, clouds and the climate system, and tries to reconstruct pre-industrial aerosol and cloud conditions from data collected in pristine environments. The number concentration of Ice Nucleating Particles (INP) is an important, yet scarcely known parameter. As a partner of Work package 1 of BACCHUS we began in September 2014 to operate a globally spanned network of four INP sampling stations, which is the first of its kind. The stations are located at the ATTO observatory in the Brazilian Rainforest, the Caribbean Sea (Martinique), the Zeppelin Observatory at Svalbard in the Arctic, and in central Europe (Germany). Samples are collected routinely every day or every few days by electrostatic precipitation of aerosol particles onto Si substrates. The samples are stored in petri-slides, and shipped to our laboratory in Frankfurt, Germany. The number of ice nucleating particles on the substrate is analyzed in the isothermal static diffusion chamber FRIDGE by growing ice on the INP and photographing and counting the crystals. The measurements in the temperature range from -20°C to -30°C and relative humidities of 100-135% (with respect to ice) address primarily the deposition/condensation nucleation modes. Here we present INP and supporting aerosol data from this novel INP network for the first time.

  15. Room-temperature particle detectors with guard rings based on semi-insulating InP co-doped with Ti and Zn

    Czech Academy of Sciences Publication Activity Database

    Yatskiv, Roman; Žďánský, Karel; Pekárek, Ladislav

    2009-01-01

    Roč. 598, č. 3 (2009), s. 759-763 ISSN 0168-9002 R&D Projects: GA AV ČR KAN400670651 Institutional research plan: CEZ:AV0Z20670512 Keywords : radiation detector * InP * crystal growth Subject RIV: JA - Electronics ; Optoelectronics, Electrical Engineering Impact factor: 1.317, year: 2009

  16. Coupling of Ag Nanoparticle with Inverse Opal Photonic Crystals as a Novel Strategy for Upconversion Emission Enhancement of NaYF4: Yb(3+), Er(3+) Nanoparticles.

    Science.gov (United States)

    Shao, Bo; Yang, Zhengwen; Wang, Yida; Li, Jun; Yang, Jianzhi; Qiu, Jianbei; Song, Zhiguo

    2015-11-18

    Rare-earth-ion-doped upconversion (UC) nanoparticles have generated considerable interest because of their potential application in solar cells, biological labeling, therapeutics, and imaging. However, the applications of UC nanoparticles were still limited because of their low emission efficiency. Photonic crystals and noble metal nanoparticles are applied extensively to enhance the UC emission of rare earth ions. In the present work, a novel substrate consisting of inverse opal photonic crystals and Ag nanoparticles was prepared by the template-assisted method, which was used to enhance the UC emission of NaYF4: Yb(3+), Er(3+) nanoparticles. The red or green UC emissions of NaYF4: Yb(3+), Er(3+) nanoparticles were selectively enhanced on the inverse opal substrates because of the Bragg reflection of the photonic band gap. Additionally, the UC emission enhancement of NaYF4: Yb(3+), Er(3+) nanoparticles induced by the coupling of metal nanoparticle plasmons and photonic crystal effects was realized on the Ag nanoparticles included in the inverse opal substrate. The present results demonstrated that coupling of Ag nanoparticle with inverse opal photonic crystals provides a useful strategy to enhance UC emission of rare-earth-ion-doped nanoparticles.

  17. Epitaxial growth of InP on SI by MOCVD

    International Nuclear Information System (INIS)

    Konushi, F.; Seki, A.; Kudo, J.; Sato, H.; Kakimoto, S.; Fukushima, T.; Kubota, Y.; Koba, M.

    1988-01-01

    The authors have studied the heteroepitaxial growth of InP on large diameter Si substrates using MOCVD. A new MOCVD system with four inch wafer size capability was utilized in the growth. Single domain InP films have been successfully grown on four inch Si substrates by using a new heterostructure with a thin GaAs intermediate layer. In this paper, the authors describe the crystalline quality and residual stress of InP epilayers, estimated by etch pit density and x-ray diffraction, respectively. The authors also reports on the reduction of EPD by post-growth annealing

  18. Susceptor and proximity rapid thermal annealing of InP

    International Nuclear Information System (INIS)

    Katz, A.; Pearton, S.J.; Geva, M.

    1990-01-01

    This paper presents a comparison between the efficiency of InP rapid thermal annealing within two types of SiC-coated graphite susceptors and by using the more conventional proximity approach, in providing degradation-free substrate surface morphology. The superiority of annealing within a susceptor was clearly demonstrated through the evaluation of AuGe contact performance to carbon-implanted InP substrates, which were annealed to activate the implants prior to the metallization. The susceptor annealing provided better protection against edge degradation, slip formation and better surface morphology, due to the elimination of P outdiffusion and pit formation. The two SiC-coated susceptors that were evaluated differ from each other in their geometry. The first type must be charged with the group V species prior to any annealing cycle. Under the optimum charging conditions, effective surface protection was provided only to one anneal (750 degrees C, 10s) of InP before charging was necessary. The second contained reservoirs for provision of the group V element partial pressure, enabled high temperature annealing at the InP without the need for continual recharging of the susceptor. Thus, one has the ability to subsequentially anneal a lot of InP wafers at high temperatures without inducing any surface deterioration

  19. Thin-Film Solar Cells with InP Absorber Layers Directly Grown on Nonepitaxial Metal Substrates

    KAUST Repository

    Zheng, Maxwell

    2015-08-25

    The design and performance of solar cells based on InP grown by the nonepitaxial thin-film vapor-liquid-solid (TF-VLS) growth technique is investigated. The cell structure consists of a Mo back contact, p-InP absorber layer, n-TiO2 electron selective contact, and indium tin oxide transparent top electrode. An ex situ p-doping process for TF-VLS grown InP is introduced. Properties of the cells such as optoelectronic uniformity and electrical behavior of grain boundaries are examined. The power conversion efficiency of first generation cells reaches 12.1% under simulated 1 sun illumination with open-circuit voltage (VOC) of 692 mV, short-circuit current (JSC) of 26.9 mA cm-2, and fill factor (FF) of 65%. The FF of the cell is limited by the series resistances in the device, including the top contact, which can be mitigated in the future through device optimization. The highest measured VOC under 1 sun is 692 mV, which approaches the optically implied VOC of ≈795 mV extracted from the luminescence yield of p-InP. The design and performance of solar cells based on indium phosphide (InP) grown by the nonepitaxial thin-film vapor-liquid-solid growth technique is investigated. The cell structure consists of a Mo back contact, p-InP absorber layer, n-TiO2 electron selective contact, and an indium tin oxide transparent top electrode. The highest measured open circuit voltage (VOC) under 1 sun is 692 mV, which approaches the optically implied VOC of ≈795 mV extracted from the luminescence yield of p-InP.

  20. Wide bandgap, strain-balanced quantum well tunnel junctions on InP substrates

    International Nuclear Information System (INIS)

    Lumb, M. P.; Yakes, M. K.; Schmieder, K. J.; Affouda, C. A.; Walters, R. J.; González, M.; Bennett, M. F.; Herrera, M.; Delgado, F. J.; Molina, S. I.

    2016-01-01

    In this work, the electrical performance of strain-balanced quantum well tunnel junctions with varying designs is presented. Strain-balanced quantum well tunnel junctions comprising compressively strained InAlAs wells and tensile-strained InAlAs barriers were grown on InP substrates using solid-source molecular beam epitaxy. The use of InAlAs enables InP-based tunnel junction devices to be produced using wide bandgap layers, enabling high electrical performance with low absorption. The impact of well and barrier thickness on the electrical performance was investigated, in addition to the impact of Si and Be doping concentration. Finally, the impact of an InGaAs quantum well at the junction interface is presented, enabling a peak tunnel current density of 47.6 A/cm 2 to be realized.

  1. Wide bandgap, strain-balanced quantum well tunnel junctions on InP substrates

    Energy Technology Data Exchange (ETDEWEB)

    Lumb, M. P. [The George Washington University, Washington, DC 20037 (United States); US Naval Research Laboratory, Washington, DC 20375 (United States); Yakes, M. K.; Schmieder, K. J.; Affouda, C. A.; Walters, R. J. [US Naval Research Laboratory, Washington, DC 20375 (United States); González, M.; Bennett, M. F. [Sotera Defense Solutions, Annapolis Junction, Maryland 20701 (United States); US Naval Research Laboratory, Washington, DC 20375 (United States); Herrera, M.; Delgado, F. J.; Molina, S. I. [University of Cádiz, 11510, Puerto Real, Cádiz (Spain)

    2016-05-21

    In this work, the electrical performance of strain-balanced quantum well tunnel junctions with varying designs is presented. Strain-balanced quantum well tunnel junctions comprising compressively strained InAlAs wells and tensile-strained InAlAs barriers were grown on InP substrates using solid-source molecular beam epitaxy. The use of InAlAs enables InP-based tunnel junction devices to be produced using wide bandgap layers, enabling high electrical performance with low absorption. The impact of well and barrier thickness on the electrical performance was investigated, in addition to the impact of Si and Be doping concentration. Finally, the impact of an InGaAs quantum well at the junction interface is presented, enabling a peak tunnel current density of 47.6 A/cm{sup 2} to be realized.

  2. Structural and vibrational study of C-type doped rare earth sesquioxide Yb2-xCoxO3

    International Nuclear Information System (INIS)

    Farhat, L. Ben; Amami, M.; Hlil, E.K.; Hassen, R. Ben

    2009-01-01

    Polycrystalline samples with general formula Yb 2-x Co x O 3 (0 2 O 3 sesquioxide. The lattice parameters are found to vary linearly with the composition x. The cationic distribution over the two non-equivalent sites 8b and 24d of the space group Ia-3 is found to be preferentially. Replacing Yb 3+ by Co 3+ introduces slight changes in the atomic coordinates leading to an increase of the mean cation-anion distances. The ability of Raman spectroscopy to detect changes in local co-ordination is utilized. A pseudo-tetrahedral coordination for the Co 3+ in the 24d site was found.

  3. Yb3+,Er3+,Eu3+-codoped YVO4 material for bioimaging with dual mode excitation

    International Nuclear Information System (INIS)

    Thao, Chu Thi Bich; Huy, Bui The; Sharipov, Mirkomil; Kim, Jin-Ik.; Dao, Van-Duong; Moon, Ja-Young; Lee, Yong-Ill

    2017-01-01

    We propose an efficient bioimaging strategy using Yb 3+ ,Er 3+ ,Eu 3+ -triplet doped YVO 4 nanoparticles which were synthesized with polymer as a template. The obtained particles possess nanoscale, uniform, and flexible excitation. The effect of Eu 3+ ions on the luminescence properties of YVO 4 :Yb 3+ ,Er 3+ ,Eu 3+ was investigated. The upconversion mechanism of the prepared material was also discussed. The structure and optical properties of the prepared material were characterized by using X-ray diffraction (XRD), Fourier-transform IR spectroscopy (FTIR), scanning electron microscopy (SEM), Transmission electron microscopy (TEM) upconversion and photoluminescence spectra. The Commission International de I′Eclairage (CIE) chromaticity coordinates was investigated to confirm the performance of color luminescent emission. The prepared YVO 4 :Yb 3+ ,Er 3+ ,Eu 3+ nanoparticles could be easily dispersed in water by surface modification with cysteine (Cys) and glutathione (GSH). The aqueous dispersion of the modified YVO 4 :Yb 3+ ,Er 3+ ,Eu 3+ exhibits bright upconversion and downconversion luminescence and has been applied for bioimaging of HeLa cells. Our developed material with dual excitation offers a promising advance in bioimaging. - Highlights: • Prepared particles possess nanoscale size, uniform, and larger scale. • The material exhibits strong emission under dual mode excitations. • The surface material has been applied for bioimaging of HeLa cell. • Low cytotoxicity, no auto-fluorescence

  4. Effect of Sintering Temperature on Microstructure, Chemical Stability, and Electrical Properties of Transition Metal or Yb-Doped BaZr{sub 0.1}Ce{sub 0.7}Y{sub 0.1}M{sub 0.1}O{sub 3−δ} (M = Fe, Ni, Co, and Yb)

    Energy Technology Data Exchange (ETDEWEB)

    Mirfakhraei, Behzad; Ramezanipour, Farshid; Paulson, Scott; Birss, Viola; Thangadurai, Venkataraman, E-mail: vthangad@ucalgary.ca [Department of Chemistry, University of Calgary, Calgary, AB (Canada)

    2014-03-13

    Perovskite-type BaZr{sub 0.1}Ce{sub 0.7}Y{sub 0.1}M{sub 0.1}O{sub 3−δ} (M = Fe, Ni, Co, and Yb) (BZCY-M) oxides were synthesized using the conventional solid-state reaction method at 1350–1550°C in air in order to investigate the effect of dopants on sintering, crystal structure, chemical stability under CO{sub 2} and H{sub 2}S, and electrical transport properties. The formation of the single-phase perovskite-type structure with an orthorhombic space group Imam was confirmed by Rietveld refinement using powder X-ray diffraction for the Fe, Co, Ni, and Yb-doped samples. The BZCY-Co and BZCY-Ni oxides show a total electrical conductivity of 0.01 and 8 × 10{sup −3} S cm{sup −1} at 600°C in wet H{sub 2} with an activation energy of 0.36 and 0.41 eV, respectively. Scanning electron microscope and energy-dispersive X-ray analysis revealed Ba and Co-rich secondary phase at the grain-boundaries, which may explain the enhancement in the total conductivity of the BZCY-Co. However, ex-solution of Ni at higher sintering temperatures, especially at 1550°C, decreases the total conductivity of the BZCY-Ni material. The Co and Ni dopants act as a sintering aid and form dense pellets at a lower sintering temperature of 1250°C. The Fe, Co, and Ni-doped BZCY-M samples synthesized at 1350°C show stability in 30 ppm H{sub 2}S/H{sub 2} at 800°C, and increasing the firing temperature to 1550°C, enhanced the chemical stability in CO{sub 2}/N{sub 2} (1:2) at 25–900°C. The BZCY-Co and BZCY-Ni compounds with high conductivity in wet H{sub 2} could be considered as possible anodes for intermediate temperature solid oxide fuel cells.

  5. Rare-earth-ion-doped ultra-narrow-linewidth lasers on a silicon chip and applications to intra-laser-cavity optical sensing

    NARCIS (Netherlands)

    Bernhardi, Edward; de Ridder, R.M.; Worhoff, Kerstin; Pollnau, Markus

    We report on diode-pumped distributed-feedback (DFB) and distributed-Bragg-reflector (DBR) channel waveguide lasers in Er-doped and Yb-doped Al2O3 on standard thermally oxidized silicon substrates. Uniform surface-relief Bragg gratings were patterned by laser-interference lithography and etched into

  6. Thermo-optical effects in high-power Ytterbium-doped fiber amplifiers

    DEFF Research Database (Denmark)

    Hansen, Kristian Rymann; Alkeskjold, Thomas Tanggaard; Broeng, Jes

    2011-01-01

    We investigate the effect of temperature gradients in high-power Yb-doped fiber amplifiers by a numerical beam propagation model, which takes thermal effects into account in a self-consistent way. The thermally induced change in the refractive index of the fiber leads to a thermal lensing effect...

  7. Functional conservation of rice OsNF-YB/YC and Arabidopsis AtNF-YB/YC proteins in the regulation of flowering time

    KAUST Repository

    Hwang, Yoon-Hyung; Kim, SoonKap; Lee, Keh Chien; Chung, Young Soo; Lee, Jeong Hwan; Kim, Jeong-Kook

    2016-01-01

    Plant NUCLEAR FACTOR Y (NF-Y) transcription factors play important roles in plant development and abiotic stress. In Arabidopsis thaliana, two NF-YB (AtNF-YB2 and AtNF-YB3) and five NF-YC (AtNF-YC1, AtNF-YC2, AtNF-YC3, AtNF-YC4, and AtNF-YC9) genes regulate photoperiodic flowering by interacting with other AtNF-Y subunit proteins. Three rice NF-YB (OsNF-YB8, OsNF-YB10, and OsNF-YB11) and five rice OsNF-YC (OsNF-YC1, OsNF-YC2, OsNF-YC4, OsNF-YC6, and OsNF-YC7) genes are clustered with two AtNF-YB and five AtNF-YC genes, respectively. To investigate the functional conservation of these NF-YB and NF-YC genes in rice and Arabidopsis, we analyzed the flowering phenotypes of transgenic plants overexpressing the respective OsNF-YB and OsNF-YC genes in Arabidopsis mutants. Overexpression of OsNF-YB8/10/11 and OsNF-YC2 complemented the late flowering phenotype of Arabidopsis nf-yb2 nf-yb3 and nf-yc3 nf-yc4 nf-yc9 mutants, respectively. The rescued phenotype of 35S::OsNF-YC2 nf-yc3 nf-yc4 nf-yc9 plants was attributed to the upregulation of FLOWERING LOCUS T (FT) and SUPPRESSOR OF OVEREXPRESSION OF CONSTANS 1 (SOC1). In vitro and in planta protein–protein analyses revealed that OsNF-YB8/10/11 and OsNF-YC1/2/4/6/7 interact with AtNF-YC3/4/9 and AtNF-YB2/3, respectively. Our data indicate that some OsNF-YB and OsNF-YC genes are functional equivalents of AtNF-YB2/3 and AtNF-YC3/4/9 genes, respectively, and suggest functional conservation of Arabidopsis and rice NF-Y genes in the control of flowering time.

  8. Functional conservation of rice OsNF-YB/YC and Arabidopsis AtNF-YB/YC proteins in the regulation of flowering time

    KAUST Repository

    Hwang, Yoon-Hyung

    2016-01-11

    Plant NUCLEAR FACTOR Y (NF-Y) transcription factors play important roles in plant development and abiotic stress. In Arabidopsis thaliana, two NF-YB (AtNF-YB2 and AtNF-YB3) and five NF-YC (AtNF-YC1, AtNF-YC2, AtNF-YC3, AtNF-YC4, and AtNF-YC9) genes regulate photoperiodic flowering by interacting with other AtNF-Y subunit proteins. Three rice NF-YB (OsNF-YB8, OsNF-YB10, and OsNF-YB11) and five rice OsNF-YC (OsNF-YC1, OsNF-YC2, OsNF-YC4, OsNF-YC6, and OsNF-YC7) genes are clustered with two AtNF-YB and five AtNF-YC genes, respectively. To investigate the functional conservation of these NF-YB and NF-YC genes in rice and Arabidopsis, we analyzed the flowering phenotypes of transgenic plants overexpressing the respective OsNF-YB and OsNF-YC genes in Arabidopsis mutants. Overexpression of OsNF-YB8/10/11 and OsNF-YC2 complemented the late flowering phenotype of Arabidopsis nf-yb2 nf-yb3 and nf-yc3 nf-yc4 nf-yc9 mutants, respectively. The rescued phenotype of 35S::OsNF-YC2 nf-yc3 nf-yc4 nf-yc9 plants was attributed to the upregulation of FLOWERING LOCUS T (FT) and SUPPRESSOR OF OVEREXPRESSION OF CONSTANS 1 (SOC1). In vitro and in planta protein–protein analyses revealed that OsNF-YB8/10/11 and OsNF-YC1/2/4/6/7 interact with AtNF-YC3/4/9 and AtNF-YB2/3, respectively. Our data indicate that some OsNF-YB and OsNF-YC genes are functional equivalents of AtNF-YB2/3 and AtNF-YC3/4/9 genes, respectively, and suggest functional conservation of Arabidopsis and rice NF-Y genes in the control of flowering time.

  9. Damage formation and annealing in InP due to swift heavy ions

    International Nuclear Information System (INIS)

    Kamarou, A.; Wesch, W.; Wendler, E.; Klaumuenzer, S.

    2004-01-01

    Virgin and pre-damaged InP samples were irradiated at room temperature (RT) and at liquid nitrogen temperature (LNT) with different fluences of 140 MeV Kr, 390 MeV Xe and 600 MeV Au ions. The pre-damaging was performed with 600 keV Ge ions at LNT to obtain different damage levels. The samples were analysed by means of Rutherford backscattering spectrometry (RBS) in random and channelling geometry. A relatively weak damage accumulation in virgin InP and a very significant defect annealing in pre-damaged InP occurs due to 140 MeV Kr irradiation. The damaging of virgin InP with 390 MeV Xe and 600 MeV Au is much more efficient in comparison with that of 140 MeV Kr. Further, annealing of the pre-damaged InP due to 390 MeV Xe irradiation is hardly visible. At LNT InP appears to be much more radiation-resistant to swift heavy ion (SHI) irradiation than at RT. Our results show that during SHI irradiation of InP both damage formation and damage annealing occur simultaneously. Whether the first or the second one plays a more important role depends on the SHI mass and energy

  10. Lanthanide-doped luminescent ionogels

    OpenAIRE

    Lunstroot, Kyra; Driesen, Kris; Nockemann, Peter; Van Hecke, Kristof; Van Meervelt, Luc; Görller-Walrand, Christiane; Binnemans, Koen; Bellayer, Séverine; Viau, Lydie; Le Bideau, Jean; Vioux, André

    2009-01-01

    Ionogels are solid oxide host networks confining at a meso-scale ionic liquids, and retaining their liquid nature. Ionogels were obtained by dissolving anthanide(III) complexes in the ionic liquid 1-hexyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide, [C6mim][Tf2N], followed by confinement of the lanthanide-doped ionic liquid mixtures in the pores of a nano-porous silica network. [C6mim][Ln(tta)4], where tta is 2-thenoyltrifluoroacetonate and Ln = Nd, Sm, Eu, Ho, Er, Yb, and [choli...

  11. Optical transitions of Ho(3+) in oxyfluoride glasses and upconversion luminescence of Ho(3+)/Yb(3+)-codoped oxyfluoride glasses.

    Science.gov (United States)

    Feng, Li; Wu, Yinsu

    2015-05-05

    Optical properties of Ho(3+)-doped SiO2-BaF2-ZnF2 glasses have been investigated on the basis of the Judd-Ofelt theory. Judd-Ofelt intensity parameters, radiative transition probabilities, fluorescence branching ratios and radiative lifetimes have been calculated for different glass compositions. Upconversion emissions were observed in Ho(3+)/Yb(3+)-codoped SiO2-BaF2-ZnF2 glasses under 980nm excitation. The effects of composition, concentration of the doping ions, and excitation pump power on the upconversion emissions were also systematically studied. Copyright © 2015 Elsevier B.V. All rights reserved.

  12. Yb{sup 3+}:Sr{sub 5}(VO{sub 4}){sub 3}F: Crystal growth, spectroscopic characterization and laser development; Yb{sup 3+}:Sr{sub 5}(VO{sub 4}){sub 3}F: Crescimento, caracterizacao espectroscopica e desenvolvimento do laser

    Energy Technology Data Exchange (ETDEWEB)

    Bustamante, Andrea Nora Pino

    1999-07-01

    Crystal growth, spectroscopic characterization and laser development of Yb{sup 3+}:SVAP [Sr{sub 5}(VO{sub 4}){sub 3}F] was performed to demonstrate for the first time, operation of tunable laser emission centered at 1120 nm. Initially, SVAP crystals were grown with high dopant concentrations, up to 6.0 mol % of Yb{sub 2} O{sub 3} in the melt, in order to investigate the material for potential laser operation at a new laser wavelength. Additional research was performed to alleviate highly doped SVAP crystals of defects previously observed. Basic spectroscopic characterization including absorption and luminescent properties were measured to better understand the behavior of Yb{sup 3+} ions in SVAP. Based upon these studies, discussion of the 1120 nm laser transition is presented as it arises from a ground state vibrational level. Investigations of the charge compensation process and the optical parameters as a function of dopant concentration are also presented. The laser development of Yb{sup 3+}:SVAP included continuous and pulsed modes of operation of the 1044 nm and 1120 nm transitions. Initial laser action of the 1044 nm transition was achieved using a Yi: Saphire laser pump source in order to compare with previously results. Further development of a diode-pumped Yb{sup 3+}:SVAP laser system demonstrated continuously tunable laser operation from 1103 nm for the first time. The laser investigations also proved that this high gain media does provide continuous wave laser action at 1044 nm and 1120 simultaneously without significant gain depletion. (author)

  13. Upper atmosphere research at INPE

    International Nuclear Information System (INIS)

    Clemesha, B.R.

    1984-01-01

    Upper atmosphere research at INPE is mainly concerned with the chemistry and dynamics of the stratosphere, upper mesosphere and lower thermosphere, and the middle thermosphere. Experimental work includes lidar observations of the stratospheric aerosol, measurements of stratospheric ozone by Dobson spectrophotometers and by balloon and rocket-borne sondes, lidar measurements of atmospheric sodium, and photometric observations of O, O 2 , OH and Na emissions, including interferrometric measurements of the OI6300 emission for the purpose of determing thermospheric winds and temperature. The airglow observations also include measurements of a number of emissions produced by the precipitation of energetic neutral particles generated by charge exchange in the ring current. Some recent results of INPE's upper atmosphere program are presented. (Author) [pt

  14. Nonepitaxial Thin-Film InP for Scalable and Efficient Photocathodes.

    Science.gov (United States)

    Hettick, Mark; Zheng, Maxwell; Lin, Yongjing; Sutter-Fella, Carolin M; Ager, Joel W; Javey, Ali

    2015-06-18

    To date, some of the highest performance photocathodes of a photoelectrochemical (PEC) cell have been shown with single-crystalline p-type InP wafers, exhibiting half-cell solar-to-hydrogen conversion efficiencies of over 14%. However, the high cost of single-crystalline InP wafers may present a challenge for future large-scale industrial deployment. Analogous to solar cells, a thin-film approach could address the cost challenges by utilizing the benefits of the InP material while decreasing the use of expensive materials and processes. Here, we demonstrate this approach, using the newly developed thin-film vapor-liquid-solid (TF-VLS) nonepitaxial growth method combined with an atomic-layer deposition protection process to create thin-film InP photocathodes with large grain size and high performance, in the first reported solar device configuration generated by materials grown with this technique. Current-voltage measurements show a photocurrent (29.4 mA/cm(2)) and onset potential (630 mV) approaching single-crystalline wafers and an overall power conversion efficiency of 11.6%, making TF-VLS InP a promising photocathode for scalable and efficient solar hydrogen generation.

  15. Surface photovoltage study of InP and Zn3P2

    International Nuclear Information System (INIS)

    Thurgate, S.M.; Lacuesta, T.D.; Huck, N.R.

    1989-01-01

    The surface photovoltage spectra of InP and Zn 3 P 2 were measured using a Kelvin probe to determine the contact potential difference between the sample and the probe as a function of the wavelength of illuminating light. The features in the resulting spectra were found to be sensitive to ion bombardment. The photovoltage spectra obtained from the InP differed from previously reported SPC spectra in that it showed clear evidence of surface states (or interfacial states) at 0.86 eV and 0.68 eV above VBM. It was found that the features in the spectrum of Zn 3 P 2 were reduced by ion bombardment, but not removed completely, whereas the features in the InP spectra were completely removed. Exposure of the ion bombarded urface to air restored the features of Zn 3 P 2 but only produced a small change in the spectrum of the InP. The loss of features in the InP spectra can be attributed to damage in the substrate caused by the ion bombardment even though the oxide layer was not removed before the damage occurred. Zn 3 P 2 was not as sensitive to ion damage as InP. (orig.)

  16. Optical properties of highly crystalline Y2O3:Er,Yb nanoparticles prepared by laser ablation in water

    International Nuclear Information System (INIS)

    Nunokawa, Takashi; Odawara, Osamu; Wada, Hiroyuki

    2014-01-01

    Y 2 O 3 :Er,Yb nanoparticles were prepared by laser ablation in water. We investigated crystallinity, distribution of dopant, and optical properties of the prepared nanoparticles. The full-width half-maximum (FWHD) of the crystalline peak of nanoparticles measured by an x-ray diffractometer (XRD) barely changed. Further, using scanning transmission electron microscopy–energy dispersive x-ray spectroscopy (STEM–EDX), we confirmed the peaks of Y, Er, Yb, and O. Moreover, on the basis of the optical properties of the nanoparticles, the emission of red ( 2 F 9/2  →  4 I 15/2 ) and green ( 2 H 11/2 , 4 S 3/2  →  4 I 15/2 ) was confirmed. We also investigated the emission intensity as a function of the excitation power of 980 nm LD in the prepared nanoparticles. The photon avalanche effect was observed at the excitation power of 100 mW. These results confirmed that uniformly Er-Yb-doped Y 2 O 3 nanoparticles were successfully prepared by laser ablation in water. (paper)

  17. Quantum sized Ag nanocluster assisted fluorescence enhancement in Tm{sup 3+}-Yb{sup 3+} doped optical fiber beyond plasmonics

    Energy Technology Data Exchange (ETDEWEB)

    Chattopadhyay, Rik; Haldar, Arindam; Paul, Mukul C.; Das, Shyamal; Bhadra, Shyamal K., E-mail: skbhadra@cgcri.res.in [Fiber Optics and Photonics Division, CSIR-Central Glass and Ceramic Research Institute, 196, Raja S. C. Mullick Road, Kolkata 700032 (India)

    2015-12-07

    We report a process for enhancing fluorescence emission from conventional rare earth ions in optical fiber by metal nanocluster (MNC) in nonresonant indirect pumping. The process is completely different from formal metal enhanced fluorescence phenomenon as the MNCs are too small in size to support localized surface plasmon and the excitation wavelength is far from plasmon resonance frequency. We used an established theory of two coupled oscillators to explain the simultaneous enhancement of Ytterbium (Yb{sup 3+}) and Thulium (Tm{sup 3+}) emission by silver (Ag) NCs under nonresonant pumping in optical fiber. The fiber is pumped with a 980 nm fiber pigtailed laser diode with input power of 20–100 mW to excite the Yb{sup 3+}. Four times enhancement of Yb{sup 3+} emission of 900–1100 nm and Tm{sup 3+} upconversion emission around 474 nm, 650 nm, and 790 nm is observed in the fiber with Ag NCs.

  18. Plasma Deposited SiO2 for Planar Self-Aligned Gate Metal-Insulator-Semiconductor Field Effect Transistors on Semi-Insulating InP

    Science.gov (United States)

    Tabory, Charles N.; Young, Paul G.; Smith, Edwyn D.; Alterovitz, Samuel A.

    1994-01-01

    Metal-insulator-semiconductor (MIS) field effect transistors were fabricated on InP substrates using a planar self-aligned gate process. A 700-1000 A gate insulator of Si02 doped with phosphorus was deposited by a direct plasma enhanced chemical vapor deposition at 400 mTorr, 275 C, 5 W, and power density of 8.5 MW/sq cm. High frequency capacitance-voltage measurements were taken on MIS capacitors which have been subjected to a 700 C anneal and an interface state density of lxl0(exp 11)/eV/cq cm was found. Current-voltage measurements of the capacitors show a breakdown voltage of 107 V/cm and a insulator resistivity of 10(exp 14) omega cm. Transistors were fabricated on semi-insulating InP using a standard planar self-aligned gate process in which the gate insulator was subjected to an ion implantation activation anneal of 700 C. MIS field effect transistors gave a maximum extrinsic transconductance of 23 mS/mm for a gate length of 3 microns. The drain current drift saturated at 87.5% of the initial current, while reaching to within 1% of the saturated value after only 1x10(exp 3). This is the first reported viable planar InP self-aligned gate transistor process reported to date.

  19. Fabrication and evaluation of chitosan/NaYF4:Yb3+/Tm3+ upconversion nanoparticles composite beads based on the gelling of Pickering emulsion droplets

    International Nuclear Information System (INIS)

    Yan, Huiqiong; Chen, Xiuqiong; Shi, Jia; Shi, Zaifeng; Sun, Wei; Lin, Qiang; Wang, Xianghui; Dai, Zihao

    2017-01-01

    The rare earth ion doped upconversion nanoparticles (UCNPs) synthesized by hydrophobic organic ligands possess poor solubility and low fluorescence quantum yield in aqueous media. To conquer this issue, NaYF 4 :Yb 3+ /Tm 3+ UCNPs, synthesized by a hydrothermal method, were coated with F127 and then assembled with chitosan to fabricate the chitosan/NaYF 4 :Yb 3+ /Tm 3+ composite beads (CS/NaYF 4 :Yb 3+ /Tm 3+ CBs) by Pickering emulsion system. The characterization results revealed that the as-synthesized NaYF 4 :Yb 3+ /Tm 3+ UCNPs with an average size of 20 nm exhibited spherical morphology, high crystallinity and characteristic emission upconversion fluorescence with an overall blue color output. The NaYF 4 :Yb 3+ /Tm 3+ UCNPs were successfully conjugated on the surface of chitosan beads by the gelling of emulsion droplets. The resultant CS/NaYF 4 :Yb 3+ /Tm 3+ CBs showed good upconversion luminescent property, drug-loading capacity, release performance and excellent biocompatibility, exhibiting great potentials in targeted drug delivery and tissue engineering with potential tracking capability and lasting release performance. - Highlights: • NaYF 4 :Yb 3+ /Tm 3+ UCNPs were coated by F127 to improve aqueous dispersibility. • NaYF 4 :Yb 3+ /Tm 3+ UCNPs were assembled with chitosan to fabricate the composite beads (CMs). • Pickering emulsions stabilized by UCNPs exhibited uniform and satisfactory emulsion droplets. • The CMs prepared by the gelling of emulsion droplet preserved upconversion luminescent property. • The resultant CMs showed good drug-loading capacity, release performance and biocompatibility.

  20. Spectroscopic determination of valence band parameters in InP

    International Nuclear Information System (INIS)

    Lewis, R.A.; Lough, B.C.C.

    2003-01-01

    Full text: The general form of the Hamiltonian for an electron or hole in a semiconductor has been given by Luttinger. The valence band is characterised by three parameters - γ 1 , γ 2 , γ 3 -now commonly known as the Luttinger parameters. Despite many investigations there is still considerable uncertainty regarding the Luttinger parameters of InP. The situation has been reviewed by Hackenberg et al. These authors themselves sought to determine the Luttinger parameters by hot-electron luminescence and discovered that many Luttinger parameter triplets were consistent with their data. We employ a spectroscopic approach to estimating valence-band parameters in InP. Calculations have been made for both the unperturbed energy levels and the energy levels in a magnetic field of acceptor impurities in semiconductors characterised by different Luttinger parameters. We compare our recent experimental data for the transitions associated with the Zn acceptor impurity in InP in magnetic fields up to 30 T to determine the most appropriate set of valence-band parameters for InP

  1. Wafer-scale self-organized InP nanopillars with controlled orientation for photovoltaic devices.

    Science.gov (United States)

    Sanatinia, Reza; Berrier, Audrey; Dhaka, Veer; Perros, Alexander P; Huhtio, Teppo; Lipsanen, Harri; Anand, Srinivasan

    2015-10-16

    A unique wafer-scale self-organization process for generation of InP nanopillars is demonstrated, which is based on maskless ion-beam etching (IBE) of InP developed to obtain the nanopillars, where the height, shape, and orientation of the nanopillars can be varied by controlling the processing parameters. The fabricated InP nanopillars exhibit broadband suppression of the reflectance, 'black InP,' a property useful for solar cells. The realization of a conformal p-n junction for carrier collection, in the fabricated solar cells, is achieved by a metalorganic vapor phase epitaxy (MOVPE) overgrowth step on the fabricated pillars. The conformal overgrowth retains the broadband anti-reflection property of the InP nanopillars, indicating the feasibility of this technology for solar cells. Surface passivation of the formed InP nanopillars using sulfur-oleylamine solution resulted in improved solar-cell characteristics. An open-circuit voltage of 0.71 V and an increase of 0.13 V compared to the unpassivated device were achieved.

  2. Simulation for silicon-compatible InGaAs-based junctionless field-effect transistor using InP buffer layer

    Science.gov (United States)

    Seo, Jae Hwa; Cho, Seongjae; Kang, In Man

    2013-10-01

    In this paper, we present the optimized performances of indium gallium arsenide (InGaAs)-based compound junctionless field-effect transistors (JLFETs) using an indium phosphide (InP) buffer layer. The proposed InGaAs-InP material combination with little lattice mismatch provides a significant improvement in current drivability securing various potential applications. Device optimization is performed in terms of primary dc parameters and characterization is investigated by two-dimensional (2D) technology computer-aided design simulations. The optimization variables were the channel doping concentration (Nch), the buffer doping concentration (Nbf), and the channel thickness (Tch). For the optimally designed InGaAs JLFET, on-state current (Ion) of 325 µA µm-1, subthreshold swing (S) of 80 mV dec-1, and current ratio (Ion/Ioff) of 109 were obtained. In the end, the results are compared with the data of silicon (Si)-based JL MOSFETs to confirm the improvements.

  3. Electrical properties of n-type and p-type InP grown by the synthesis, solute diffusion technique

    International Nuclear Information System (INIS)

    Siegel, W.; Kuehnel, G.; Koi, H.; Gerlach, W.

    1986-01-01

    Undoped n-InP and Zn-doped p-InP are grown by the SSD method. Hall measurements on wafers cut from the polycrystalline n-InP ingots give values between 10 15 and 10 16 cm -3 for the carrier concentration averaged over the crystallites of the wafer. From the electron mobilities measured at 77 K on single crystalline samples (maximally 5.0 x 10 4 cm 2 /Vs) it can be concluded on the high purity and perfection of this material. Zn doping yields p-InP with p = (3 to 4) x 10 16 cm -3 and μ = (113 to 140) cm 2 /Vs at room temperature. The hole mobilities at 77 K (1700 to 2160 cm 2 /Vs) are the highest ones reported for InP up to now. By fitting of the p(T) curves between 30 and 500 K concentrations and activation energies for the shallow acceptor Zn and for a medium deep acceptor present beside Zn are determined. (author)

  4. Carrier thermalization dynamics in single zincblende and wurtzite InP Nanowires.

    Science.gov (United States)

    Wang, Yuda; Jackson, Howard E; Smith, Leigh M; Burgess, Tim; Paiman, Suriati; Gao, Qiang; Tan, Hark Hoe; Jagadish, Chennupati

    2014-12-10

    Using transient Rayleigh scattering (TRS) measurements, we obtain photoexcited carrier thermalization dynamics for both zincblende (ZB) and wurtzite (WZ) InP single nanowires (NW) with picosecond resolution. A phenomenological fitting model based on direct band-to-band transition theory is developed to extract the electron-hole-plasma density and temperature as a function of time from TRS measurements of single nanowires, which have complex valence band structures. We find that the thermalization dynamics of hot carriers depends strongly on material (GaAs NW vs InP NW) and less strongly on crystal structure (ZB vs WZ). The thermalization dynamics of ZB and WZ InP NWs are similar. But a comparison of the thermalization dynamics in ZB and WZ InP NWs with ZB GaAs NWs reveals more than an order of magnitude slower relaxation for the InP NWs. We interpret these results as reflecting their distinctive phonon band structures that lead to different hot phonon effects. Knowledge of hot carrier thermalization dynamics is an essential component for effective incorporation of nanowire materials into electronic devices.

  5. PIXE channeling for concentration and location measurements of Zn- and Cd-dopants in InP single crystals

    International Nuclear Information System (INIS)

    Vogt, J.; Krause, H.; Flagmeyer, R.; Otto, G.; Lux, M.

    1993-01-01

    We present results of the determination of Cd- and Zn-dopants in InP single crystals using the PIXE and RBS spectrometry at our 2 MeV Van de Graaff accelerator. The (100) oriented crystals were doped by thermodiffusion of Cd and Zn atoms. For concentration and localization measurements we used the ion-channeling technique and energy dispersive spectrometry of proton induced X-ray emission (PIXE). Angular scans of the K-lines of In, Cd and Zn were obtained. The strong In X-rays were attenuated by a rhodium foil in front of the low energy Ge detector. The PIXE-channeling results were compared with SIMS and Hall-effect measurements. (orig.)

  6. Structure-property relations in new fluorophosphate glasses singly- and co-doped with Er{sup 3+} and Yb{sup 3+}

    Energy Technology Data Exchange (ETDEWEB)

    Gonçalves, Tássia S.; Moreira Silva, Raphaell J.; Oliveira Junior, Marcos de; Ferrari, Cynthia R. [Physics Institute of São Carlos, University of São Paulo, São Carlos, SP 13566-590 (Brazil); Poirier, Gäel Y. [Science and Technology Institute, Federal University of Alfenas, Poços de Caldas, MG 37715-400 (Brazil); Eckert, Hellmut, E-mail: eckert@ifsc.usp.br [Physics Institute of São Carlos, University of São Paulo, São Carlos, SP 13566-590 (Brazil); Physical Chemistry Institute, Westfälische Wilhelms Universität Münster, Münster D-48149 (Germany); Camargo, Andrea S.S. de, E-mail: andreasc@ifsc.usp.br [Physics Institute of São Carlos, University of São Paulo, São Carlos, SP 13566-590 (Brazil)

    2015-05-01

    Rare earth (RE{sup 3+})-doped fluorophosphate glasses are among the most promising candidates for high-efficiency laser generation in the near-infrared spectral region. By proper choice of composition, these materials can combine the advantages of fluorides (low phonon energies, low refractive indices, extensive optical window, low hygroscopicity) and of oxides (high chemical and mechanical stability and high dopant solubility), resulting in enhancement of the RE{sup 3+} emissive properties. In this work, we present the synthesis and structural/spectroscopic investigation of new glasses with composition 25BaF{sub 2}25SrF{sub 2}(30-x)Al(PO{sub 3}){sub 3}xAlF{sub 3}(20-z)YF{sub 3}:zREF{sub 3}, where x = 20 or 15, RE = Er{sup 3+} and/or Yb{sup 3+}, z = 0.25–5.0 mol%. Results indicate considerable improvement of the emissive properties of both ions when compared to phosphate or even other fluorophosphate host compositions. Long excited state lifetimes (τ = 10 ms for the Er{sup 3+} level {sup 4}I{sub 13/2}, and τ = 1.3 ms for the Yb{sup 3+} level {sup 2}F{sub 5/2}) imply high fluorescence quantum efficiencies η (up to 85% for both ions). Structural characterization by Raman and multinuclear solid state NMR spectroscopies indicate that the metaphosphate-type chain structure of the Al(PO{sub 3}){sub 3} vitreous framework is partially depolymerized and dominated by Q{sup (0)} and Q{sup (1)} units crosslinked by six-coordinate Al species. As revealed by {sup 27}Al{"3"1P} rotational echo double resonance (REDOR) NMR results the average local aluminum environment of the x = 20 sample comprises 1.6 phosphate and 4.4 fluoride species. These results indicate a clear bonding preference between aluminum and phosphorus, which is consistent with the desired dominance of fluoride species in the local environment of the rare earth and alkaline earth atoms in these glasses. - Highlights: • New fluorophosphate glass composition with excellent photophysical properties.

  7. Tm-Yb Doped Optical Fiber Performance with Variation of Host-Glass Composition

    Directory of Open Access Journals (Sweden)

    Anirban Dhar

    2014-01-01

    Full Text Available The fabrication process of Thulium-Ytterbium doped optical fiber comprising different host glass through the Modified Chemical Vapor Deposition (MCVD coupled with solution doping technique is presented. The material and optical performance of different fibers are compared with special emphasis on their lasing efficiency for 2 µm application.

  8. Energy transfer and infrared-to-visible upconversion luminescence of Er3+/Yb3+-codoped halide modified tellurite glasses

    International Nuclear Information System (INIS)

    Zhang, Q.Y.; Feng, Z.M.; Yang, Z.M.; Jiang, Z.H.

    2006-01-01

    We report on the energy transfer and frequency upconversion spectroscopic properties of Er 3+ -doped and Er 3+ /Yb 3+ -codoped TeO 2 -ZnO-Na 2 O-PbCl 2 halide modified tellurite glasses upon excitation with 808 and 978 nm laser diode. Three intense emissions centered at around 529, 546 and 657 nm, alongwith a very weak blue emission at 410 nm have clearly been observed for the Er 3+ /Yb 3+ -codoped halide modified tellurite glasses upon excitation at 978 nm and the involved mechanisms are explained. The quadratic dependence of fluorescence on excitation laser power confirms the fact that the two-photon contribute to the infrared to green-red upconversion emissions. And the blue upconversion at 410 nm involved a sequential three-photon absorption process

  9. Genome-wide analysis of the human Alu Yb-lineage

    Directory of Open Access Journals (Sweden)

    Carter Anthony B

    2004-03-01

    Full Text Available Abstract The Alu Yb-lineage is a 'young' primarily human-specific group of short interspersed element (SINE subfamilies that have integrated throughout the human genome. In this study, we have computationally screened the draft sequence of the human genome for Alu Yb-lineage subfamily members present on autosomal chromosomes. A total of 1,733 Yb Alu subfamily members have integrated into human autosomes. The average ages of Yb-lineage subfamilies, Yb7, Yb8 and Yb9, are estimated as 4.81, 2.39 and 2.32 million years, respectively. In order to determine the contribution of the Alu Yb-lineage to human genomic diversity, 1,202 loci were analysed using polymerase chain reaction (PCR-based assays, which amplify the genomic regions containing individual Yb-lineage subfamily members. Approximately 20 per cent of the Yb-lineage Alu elements are polymorphic for insertion presence/absence in the human genome. Fewer than 0.5 per cent of the Yb loci also demonstrate insertions at orthologous positions in non-human primate genomes. Genomic sequencing of these unusual loci demonstrates that each of the orthologous loci from non-human primate genomes contains older Y, Sg and Sx Alu family members that have been altered, through various mechanisms, into Yb8 sequences. These data suggest that Alu Yb-lineage subfamily members are largely restricted to the human genome. The high copy number, level of insertion polymorphism and estimated age indicate that members of the Alu Yb elements will be useful in a wide range of genetic analyses.

  10. Are there non-statistical effects in /sup 173/Yb(n,gamma)/sup 174/Yb?

    International Nuclear Information System (INIS)

    Pospisil, S.; Becvar, F.; Chrien, R.E.; Kopecky, J.

    1987-01-01

    The resonance-averaged capture of neutrons in 173 Yb has been studied at energy of 2 keV. With a statistical significance of 99.5% an enhancement of E1-transition to the neutron 2QP levels in 174 Yb is observed. 8 refs

  11. Downshifting by energy transfer in Eu{sup 3+}/Yb{sup 3+} codoped Ba{sub 4}La{sub 6}(SiO{sub 4}){sub 6}O glass ceramics

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, W.J., E-mail: wjzhang03@163.com [School of Material Science and Engineering and Shandong Provincial Key Lab of Preparation and Measurement of Building Materials, University of Jinan, Jinan 250022 (China); State Key Lab of Luminescent Materials and Devices and Institute of Optical Communication Materials, South China University of Technology, Guangzhou 510641 (China); Li, X.B.; Wu, L.J.; Yu, Y.Y.; Wang, X.Z.; Liu, S.Q.; Wang, Z. [School of Material Science and Engineering and Shandong Provincial Key Lab of Preparation and Measurement of Building Materials, University of Jinan, Jinan 250022 (China); Wang, W.C.; Liu, Y. [State Key Lab of Luminescent Materials and Devices and Institute of Optical Communication Materials, South China University of Technology, Guangzhou 510641 (China)

    2017-03-01

    We report on an efficient near-infrared downshifting in Eu{sup 3+}/Yb{sup 3+} codoped glass ceramics containing Ba{sub 4}La{sub 6}(SiO{sub 4}){sub 6}O crystals. The structural and luminescence properties were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), static and dynamic photoemission and excitation spectroscopy. After crystallization, the doping ions are found to be selectively incorporated into the precipitated oxyapatite crystals on La{sup 3+} sites, contributing to the remarkably enhanced visible emission of Eu{sup 3+} under 394 nm excitation. The Eu{sup 3+}/Yb{sup 3+} codoped glass ceramics additionally exhibits efficient near-infrared luminescence of Yb{sup 3+} around 1000 nm upon photon excitation of Eu{sup 3+} within the 300–550 nm range. The reduced visible emission and decay time of {sup 5}D{sub 0} state with Yb{sup 3+} codoping further confirm the energy transfer from Eu{sup 3+} to Yb{sup 3+}, which is promoted due to the shortened distance between Eu{sup 3+} and Yb{sup 3+} within crystals. The maximum energy transfer efficiency is evaluated to be 61%. It is revealed that energy transfer process occurs predominantly through the cross relaxation of Eu{sup 3+}({sup 5}D{sub 0}) + Yb{sup 3+}({sup 2}F{sub 7/2}) → Eu{sup 3+}({sup 7}F{sub 6}) + Yb{sup 3+}({sup 7}F{sub 5/2}).

  12. TP53inp1 Gene Is Implicated in Early Radiation Response in Human Fibroblast Cells

    Directory of Open Access Journals (Sweden)

    Nikolett Sándor

    2015-10-01

    Full Text Available Tumor protein 53-induced nuclear protein-1 (TP53inp1 is expressed by activation via p53 and p73. The purpose of our study was to investigate the role of TP53inp1 in response of fibroblasts to ionizing radiation. γ-Ray radiation dose-dependently induces the expression of TP53inp1 in human immortalized fibroblast (F11hT cells. Stable silencing of TP53inp1 was done via lentiviral transfection of shRNA in F11hT cells. After irradiation the clonogenic survival of TP53inp1 knockdown (F11hT-shTP cells was compared to cells transfected with non-targeting (NT shRNA. Radiation-induced senescence was measured by SA-β-Gal staining and autophagy was detected by Acridine Orange dye and microtubule-associated protein-1 light chain 3 (LC3B immunostaining. The expression of TP53inp1, GDF-15, and CDKN1A and alterations in radiation induced mitochondrial DNA deletions were evaluated by qPCR. TP53inp1 was required for radiation (IR induced maximal elevation of CDKN1A and GDF-15 expressions. Mitochondrial DNA deletions were increased and autophagy was deregulated following irradiation in the absence of TP53inp1. Finally, we showed that silencing of TP53inp1 enhances the radiation sensitivity of fibroblast cells. These data suggest functional roles for TP53inp1 in radiation-induced autophagy and survival. Taken together, we suppose that silencing of TP53inp1 leads radiation induced autophagy impairment and induces accumulation of damaged mitochondria in primary human fibroblasts.

  13. Ultralow surface recombination velocity in InP nanowires probed by terahertz spectroscopy.

    Science.gov (United States)

    Joyce, Hannah J; Wong-Leung, Jennifer; Yong, Chaw-Keong; Docherty, Callum J; Paiman, Suriati; Gao, Qiang; Tan, H Hoe; Jagadish, Chennupati; Lloyd-Hughes, James; Herz, Laura M; Johnston, Michael B

    2012-10-10

    Using transient terahertz photoconductivity measurements, we have made noncontact, room temperature measurements of the ultrafast charge carrier dynamics in InP nanowires. InP nanowires exhibited a very long photoconductivity lifetime of over 1 ns, and carrier lifetimes were remarkably insensitive to surface states despite the large nanowire surface area-to-volume ratio. An exceptionally low surface recombination velocity (170 cm/s) was recorded at room temperature. These results suggest that InP nanowires are prime candidates for optoelectronic devices, particularly photovoltaic devices, without the need for surface passivation. We found that the carrier mobility is not limited by nanowire diameter but is strongly limited by the presence of planar crystallographic defects such as stacking faults in these predominantly wurtzite nanowires. These findings show the great potential of very narrow InP nanowires for electronic devices but indicate that improvements in the crystallographic uniformity of InP nanowires will be critical for future nanowire device engineering.

  14. Heterostructures (CaSrBa)F2 on InP for Optoelectronics

    National Research Council Canada - National Science Library

    Pyshkin, Sergei

    1995-01-01

    Temperature-reduced MBE growth of group II-a fluorides onto InP( 100) surface as well as optimal cleaning and passivation procedures for InP wafers have been newly developed taking into account exsisting literature data...

  15. All-optical signal processing using InP photonic-crystal nanocavity switches

    DEFF Research Database (Denmark)

    Yu, Yi; Vukovic, Dragana; Heuck, Mikkel

    2014-01-01

    In this paper, we present recent progress in experimental characterization of InP photonic-crystal nanocavity switches. Pump-probe measurements on an InP PhC H0 cavity show large-contrast ultrafast switching at low pulse energy. At large pulse energies, a large resonance shift passing across...... for the joint effects of fast carrier diffusion, slow surface and bulk recombination. Utilizin g the simple InP PhC nanocavity structure, we successfully dem onstrate 10-Gb/s RZ- OOK all-optical modulation with low energy consumption....

  16. Comparison on different repetition rate locking methods in Er-doped fiber laser

    Science.gov (United States)

    Yang, Kangwen; Zhao, Peng; Luo, Jiang; Huang, Kun; Hao, Qiang; Zeng, Heping

    2018-05-01

    We demonstrate a systematic comparative research on the all-optical, mechanical and opto-mechanical repetition rate control methods in an Er-doped fiber laser. A piece of Yb-doped fiber, a piezoelectric transducer and an electronic polarization controller are simultaneously added in the laser cavity as different cavity length modulators. By measuring the cavity length tuning ranges, the output power fluctuations, the temporal and frequency repetition rate stability, we show that all-optical method introduces the minimal disturbances under current experimental condition.

  17. Radiation effects in heteroepitaxial InP solar cells

    Science.gov (United States)

    Weinberg, I.; Curtis, H. B.; Swartz, C. K.; Brinker, D. J.; Vargas-Aburto, C.

    1993-01-01

    Heteroepitaxial InP solar cells, with GaAs substrates, were irradiated by 0.5 and 3 MeV protons and their performance, temperature dependency, and carrier removal rates determined as a function of fluence. The radiation resistance of the present cells was significantly greater than that of non-heteroepitaxial InP cells at both proton energies. A clear difference in the temperature dependency of V(sub oc), was observed between heteroepitaxial and homoepitaxial InP cells. The analytically predicted dependence of dV(sub oc)/dT on Voc was confirmed by the fluence dependence of these quantities. Carrier removal was observed to increase with decreasing proton energy. The results obtained for performance and temperature dependency were attributed to the high dislocation densities present in the heteroepitaxial cells while the energy dependence of carrier removal was attributed to the energy dependence of proton range.

  18. Different growth regimes in InP nanowire growth mediated by Ag nanoparticles.

    Science.gov (United States)

    Oliveira, D S; Zavarize, M; Tizei, L H G; Walls, M; Ospina, C A; Iikawa, F; Ugarte, D; Cotta, M A

    2017-12-15

    We report on the existence of two different regimes in one-step Ag-seeded InP nanowire growth. The vapor-liquid-solid-mechanism is present at larger In precursor flows and temperatures, ∼500 °C, yielding high aspect ratio and pure wurtzite InP nanowires with a semi-spherical metal particle at the thin apex. Periodic diameter oscillations can be achieved under extreme In supersaturations at this temperature range, showing the presence of a liquid catalyst. However, under lower temperatures and In precursor flows, large diameter InP nanowires with mixed wurtzite/zincblende segments are obtained, similarly to In-assisted growth. Chemical composition analysis suggest that In-rich droplet formation is catalyzed at the substrate surface via Ag nanoparticles; this process might be facilitated by the sulfur contamination detected in these nanoparticles. Furthermore, part of the original Ag nanoparticle remains solid and is embedded inside the actual catalyst, providing an in situ method to switch growth mechanisms upon changing In precursor flow. Nevertheless, our Ag-seeded InP nanowires exhibit overall optical emission spectra consistent with the observed structural properties and similar to Au-catalyzed InP nanowires. We thus show that Ag nanoparticles may be a suitable replacement for Au in InP nanowire growth.

  19. Optimization of the short-circuit current in an InP nanowire array solar cell through opto-electronic modeling.

    Science.gov (United States)

    Chen, Yang; Kivisaari, Pyry; Pistol, Mats-Erik; Anttu, Nicklas

    2016-09-23

    InP nanowire arrays with axial p-i-n junctions are promising devices for next-generation photovoltaics, with a demonstrated efficiency of 13.8%. However, the short-circuit current in such arrays does not match their absorption performance. Here, through combined optical and electrical modeling, we study how the absorption of photons and separation of the resulting photogenerated electron-hole pairs define and limit the short-circuit current in the nanowires. We identify how photogenerated minority carriers in the top n segment (i.e. holes) diffuse to the ohmic top contact where they recombine without contributing to the short-circuit current. In our modeling, such contact recombination can lead to a 60% drop in the short-circuit current. To hinder such hole diffusion, we include a gradient doping profile in the n segment to create a front surface barrier. This approach leads to a modest 5% increase in the short-circuit current, limited by Auger recombination with increased doping. A more efficient approach is to switch the n segment to a material with a higher band gap, like GaP. Then, a much smaller number of holes is photogenerated in the n segment, strongly limiting the amount that can diffuse and disappear into the top contact. For a 500 nm long top segment, the GaP approach leads to a 50% higher short-circuit current than with an InP top segment. Such a long top segment could facilitate the fabrication and contacting of nanowire array solar cells. Such design schemes for managing minority carriers could open the door to higher performance in single- and multi-junction nanowire-based solar cells.

  20. Spectroscopy and visible frequency upconversion in Er3+-Yb3+: TeO2-ZnO glass.

    Science.gov (United States)

    Mohanty, Deepak Kumar; Rai, Vineet Kumar

    2014-01-01

    The UV-Vis-NIR absorption studies of the Er(3+)/Er(3+)-Yb(3+) doped/codoped TeO2-ZnO (TZO) glasses fabricated by the melting and quenching method has been performed. The spectroscopic radiative parameters viz. radiative transition probabilities, branching ratios and lifetimes have been determined from the absorption spectrum by using Judd-Ofelt theory. The near infrared (NIR) to visible frequency upconversion (UC) have been monitored by using an excitation of 976 nm wavelength radiation from a CW diode laser. The effect of codoping with Yb(3+) ions on the intensity of the UC emission bands from the Er(3+) ions throughout visible region has been studied. The mechanism responsible for the observed upconversion emissions in the prepared samples have been explained on the basis of excited state absorption and efficient energy transfer processes. Copyright © 2013 Elsevier B.V. All rights reserved.

  1. Control of persistent photoconductivity in nanostructured InP through morphology design

    International Nuclear Information System (INIS)

    Monaico, Ed; Postolache, V; Borodin, E; Lupan, O; Tiginyanu, I M; Ursaki, V V; Adelung, R; Nielsch, K

    2015-01-01

    In this paper, we show that long-duration-photoconductivity decay (LDPCD) and persistent photoconductivity (PPC) in porous InP structures fabricated by anodic etching of bulk substrates can be controlled through the modification of the sample morphology. Particularly, the PPC inherent at low temperatures to porous InP layers with the thickness of skeleton walls comparable with pore diameters is quenched in structures consisting of ultrathin walls produced at high anodization voltages. The relaxation of photoconductivity in bulk InP substrates, porous layers, and utrathin membranes is investigated as a function of temperature and excitation power density. The obtained results suggest that PPC in porous InP layers is due to porosity induced potential barriers which hinder the recombination of photoexcited carriers, while the photoconductivity relaxation processes in ultrathin membranes are governed by surface states. (paper)

  2. Cryogenic Yb: YAG Thin-Disk Laser

    Science.gov (United States)

    2016-09-09

    as a 4- level laser. Its absorption and emission cross-sections increase, and its thermal conductivity improves. Yb:YAG thin disk laser performance...Air Force Base, NM USA 87117 4RINI Technologies, 582 South Econ Circle, Oviedo, FL USA 32765 Keywords: Laser materials; Lasers, ytterbium...temperatures, Yb:YAG behaves as a 4- level laser. Its absorption and emission cross-sections increase, and its thermal conductivity improves. Yb:YAG

  3. Cryogenic Yb:YAG laser pumped by VBG-stabilized narrowband laser diode at 969 nm

    Czech Academy of Sciences Publication Activity Database

    Jambunathan, Venkatesan; Horáčková, Lucie; Navrátil, Petr; Lucianetti, Antonio; Mocek, Tomáš

    2016-01-01

    Roč. 128, č. 12 (2016), s. 1328-1331 ISSN 1041-1135 R&D Projects: GA MŠk EE2.3.20.0143; GA ČR GA14-01660S Grant - others:HILASE(XE) CZ.1.05/2.1.00/01.0027; HILASE(XE) CZ.1.05/2.1.00/01.0027; OP VK 6(XE) CZ.1.07/2.3.00/20.0143 Institutional support: RVO:68378271 Keywords : Diode-pumped * cryogenic * volume Bragg grating * Yb doped * solid state lasers Subject RIV: BH - Optics, Masers, Lasers Impact factor: 2.375, year: 2016

  4. Optical phonon modes of wurtzite InP

    Science.gov (United States)

    Gadret, E. G.; de Lima, M. M.; Madureira, J. R.; Chiaramonte, T.; Cotta, M. A.; Iikawa, F.; Cantarero, A.

    2013-03-01

    Optical vibration modes of InP nanowires in the wurtzite phase were investigated by Raman scattering spectroscopy. The wires were grown along the [0001] axis by the vapor-liquid-solid method. The A1(TO), E2h, and E1(TO) phonon modes of the wurtzite symmetry were identified by using light linearly polarized along different directions in backscattering configuration. Additionally, forbidden longitudinal optical modes have also been observed. Furthermore, by applying an extended 11-parameter rigid-ion model, the complete dispersion relations of InP in the wurtzite phase have been calculated, showing a good agreement with the Raman experimental data.

  5. Synthesis of colloidal InP nanocrystal quantum dots

    International Nuclear Information System (INIS)

    Sirbu, L.; Gutul, T.; Todosiciuc, A.; Danila, M.; Muller, R.; Sarua, A.; Webster, R.; Tiginyanu, I.M.; Ursaki, V.

    2013-01-01

    InP nano dots with the diameter of 4-10 nm were synthesized using sol-gel method. The nano dot dimensions were obtained using TEM, and we found the d(111) spacing to be 0.328 nm which agrees within 3% of the literature value. Prepared nanoparticles where characterized then by Raman spectroscopy and Xray diffraction. Performed measurements confirm good crystalline quality of obtained InP particles, which can be used as a basis for THz emitters, LED, and OLED displays. (authors)

  6. Upconversion luminescence and blackbody radiation in tetragonal YSZ co-doped with Tm(3+) and Yb(3+).

    Science.gov (United States)

    Soares, M R N; Ferro, M; Costa, F M; Monteiro, T

    2015-12-21

    Lanthanide doped inorganic nanoparticles with upconversion luminescence are of utmost importance for biomedical applications, solid state lighting and photovoltaics. In this work we studied the downshifted luminescence, upconversion luminescence (UCL) and blackbody radiation of tetragonal yttrium stabilized zirconia co-doped with Tm(3+) and Yb(3+) single crystals and nanoparticles produced by laser floating zone and laser ablation in liquids, respectively. The photoluminescence (PL) and PL excitation (PLE) were investigated at room temperature (RT). PL spectra exhibit the characteristic lines in UV, blue/green, red and NIR regions of the Tm(3+) (4f(12)) under resonant excitation into the high energy (2S+1)LJ multiplets. Under NIR excitation (980 nm), the samples placed in air display an intense NIR at ∼800 nm due to the (1)G4→(3)H5/(3)H4→(3)H6 transitions. Additionally, red, blue/green and ultraviolet UCL is observed arising from higher excited (1)G4 and (1)D2 multiplets. The power excitation dependence of the UCL intensity indicated that 2-3 low energy absorbed photons are involved in the UCL for low power levels, while for high powers, the identified saturation is dependent on the material size with a enhanced effect on the NPs. The temperature dependence of the UCL was investigated for single crystals and targets used in the ablation. An overall increase of the integrated intensity was found to occur between 12 K and the RT. The thermally activated process is described by activation energies of 10 meV and 30 meV for single crystals and targets, respectively. For the NPs, the UCL was found to be strongly sensitive to pressure conditions. Under vacuum conditions, instead of the narrow lines of the Tm(3+), a wide blackbody radiation was detected, responsible for the change in the emission colour from blue to orange. This phenomenon is totally reversible when the NPs are placed at ambient pressure. The UCL/blackbody radiation in the nanosized material exhibits

  7. Ag2O dependent up-conversion luminescence properties in Tm3+/Er3+/Yb3+ co-doped oxyfluorogermanate glasses

    International Nuclear Information System (INIS)

    Hu, Yuebo; Qiu, Jianbei; Song, Zhiguo; Zhou, Dacheng

    2014-01-01

    Up-conversion (UC) luminescence properties of Ag/Tm 3+ /Er 3+ /Yb 3+ co-doped oxyfluorogermanate glasses have been studied to assess the effective role of silver nanoparticles as a sensitizer for Tm 3+ and Er 3+ ions. The X-ray diffraction patterns obtained in this work do not reveal any crystalline phase in the glass. However, the absorption spectra reveal that surface plasmons resonance band of Ag undergoes a distinct split with two maxima and a very broad absorption peak with a background that extends toward the near infrared (NIR) with the increasing of Ag 2 O added concentration. Transmission electron microscope images confirm that silver nanoparticles have been precipitated from matrix glasses and show their distribution, size, and shapes. In addition, changes in UC luminescence intensity of four emission bands 476, 524, 546, and 658 nm corresponding to 1 G 4 → 3 H 6 (Tm 3+ ), ( 2 H 11/2 , 4 S 3/2 ) → 4 I 15/2 (Er 3+ ), and 4 F 9/2 → 4 I 15/2 (Er 3+ ) transitions, respectively, as a function of silver addition to the base composition have been measured under 980 nm excitation. It is confirmed that Ag 2 O added concentration plays an important role in increasing the UC luminescence intensity; however, further increase in Ag 2 O added concentration reduces the intensity

  8. Multicolor tuning towards single red-emission band of upconversion nanoparticles for tunable optical component and optical/x-ray imaging agents via Ce"3"+ doping

    International Nuclear Information System (INIS)

    Yi, Zhigao; Zeng, Tianmei; Xu, Yaru; Qian, Chao; Liu, Hongrong; Zeng, Songjun; Lu, Wei; Hao, Jianhua

    2015-01-01

    A simple strategy of Ce"3"+ doping is proposed to realize multicolor tuning and predominant red emission in BaLnF_5:Yb"3"+/Ho"3"+ (Ln"3"+ = Gd"3"+, Y"3"+, Yb"3"+) systems. A tunable upconversion (UC) multicolor output from green/yellow to red can be readily achieved in a fixed Yb"3"+/Ho"3"+ composition by doping Ce"3"+, providing an effective route for multicolor tuning widely used for various optical components. Moreover, compared with Ce"3"+-free UC nanoparticles (UCNPs), a remarkable enhancement of the red-to-green (R/G) ratio is observed by doping 30% Ce"3"+, arising from the two largely promoted cross-relaxation (CR) processes between Ce"3"+ and Ho"3"+. UCNPs with pure red emission are selected as in vivo UC bioimaging agents, demonstrating the merits of deep penetration depth, the absence of autofluorescence and high contrast in small animal bioimaging. Moreover, such fluorescence imaging nanoprobes can also be used as contrast agents for three-dimensional (3D) x-ray bioimaging by taking advantage of the high K-edge values and x-ray absorption coefficients of Ba"2"+, Gd"3"+, and Ce"3"+ in our designed nanoprobes. Thus, the simultaneous realization of multicolor output, highly enhanced R/G ratio, and predominant red emission makes the Ce"3"+-doped UCNPs very useful for widespread applications in optical components and bioimaging. (paper)

  9. Multicolor tuning towards single red-emission band of upconversion nanoparticles for tunable optical component and optical/x-ray imaging agents via Ce(3+) doping.

    Science.gov (United States)

    Yi, Zhigao; Zeng, Tianmei; Xu, Yaru; Lu, Wei; Qian, Chao; Liu, Hongrong; Zeng, Songjun; Hao, Jianhua

    2015-09-25

    A simple strategy of Ce(3+) doping is proposed to realize multicolor tuning and predominant red emission in BaLnF5:Yb(3+)/Ho(3+) (Ln(3+) = Gd(3+), Y(3+), Yb(3+)) systems. A tunable upconversion (UC) multicolor output from green/yellow to red can be readily achieved in a fixed Yb(3+)/Ho(3+) composition by doping Ce(3+), providing an effective route for multicolor tuning widely used for various optical components. Moreover, compared with Ce(3+)-free UC nanoparticles (UCNPs), a remarkable enhancement of the red-to-green (R/G) ratio is observed by doping 30% Ce(3+), arising from the two largely promoted cross-relaxation (CR) processes between Ce(3+) and Ho(3+). UCNPs with pure red emission are selected as in vivo UC bioimaging agents, demonstrating the merits of deep penetration depth, the absence of autofluorescence and high contrast in small animal bioimaging. Moreover, such fluorescence imaging nanoprobes can also be used as contrast agents for three-dimensional (3D) x-ray bioimaging by taking advantage of the high K-edge values and x-ray absorption coefficients of Ba(2+), Gd(3+), and Ce(3+) in our designed nanoprobes. Thus, the simultaneous realization of multicolor output, highly enhanced R/G ratio, and predominant red emission makes the Ce(3+)-doped UCNPs very useful for widespread applications in optical components and bioimaging.

  10. InP quantum dots embedded in GaP: Optical properties and carrier dynamics

    International Nuclear Information System (INIS)

    Hatami, F.; Masselink, W.T.; Schrottke, L.; Tomm, J.W.; Talalaev, V.; Kristukat, C.; Goni, A.R.

    2003-01-01

    The optical emission and dynamics of carriers in Stranski-Krastanow self-organized InP quantum dots embedded in a GaP matrix are studied. InP deposited on GaP (001) using gas-source molecular-beam epitaxy forms quantum dots for InP coverage greater than 1.8 monolayers. Strong photoluminescence from the quantum dots is observed up to room temperature at about 2 eV; photoluminescence from the two-dimensional InP wetting layer is measured at about 2.2 eV. Modeling based on the 'model-solid theory' indicates that the band alignment for the InP quantum dots is direct and type I. Furthermore, low-temperature time-resolved photoluminescence measurements indicate that the carrier lifetime in the quantum dots is about 2 ns, typical for type-I quantum dots. Pressure-dependent photoluminescence measurements provide further evidence for a type-I band alignment for InP/GaP quantum dots at normal pressure with the GaP X states lying about 30 meV higher than the Γ states in the InP quantum dots, but indicate that they become type II under hydrostatic pressures of about 1.2 GPa

  11. 1.0 MeV irradiation of OHMIC, MS, MIS contacts to InP

    International Nuclear Information System (INIS)

    Warren, C.E.; Wagner, B.F.; Anderson, W.A.

    1986-01-01

    The radiation effects of 1.0 MeV electrons with a dose of 10/sup 15/cm/sup -2/ to MS and MIS Schottky diodes on InP have been compared to the radiation effects of MIS diodes on GaAs and Si. The radiation effects to ohmic contacts were also investigated. The metal for the diodes on the InP was gold. Au/Ti/Al was used for the GaAs diodes and Cr for the silicon diodes. Oxide layers on InP were grown by anodization in 0.1 N KOH. Oxides to GaAs and Si were grown thermally. Ohmic contacts to InP were formed using AuGe/Ni and AuSn alloys, followed by annealing in N/sub 2//H/sub 2/ (85%/15%). Metal Semiconductor diodes on InP were found to be at least sensitive to the irradiation. The InP MS and MIS diodes showed only small changes in the current voltage (I-V) characteristic, whereas the GaAs and Si devices showed a decrease in reverse current after irradiation. The ohmic contact resistance was increased by a factor of 2 to 5 after irradiation

  12. InP Heterojunction Bipolar Transistor Amplifiers to 255 GHz

    Science.gov (United States)

    Radisic, Vesna; Sawdai, Donald; Scott, Dennis; Deal, William; Dang, Linh; Li, Danny; Cavus, Abdullah; To, Richard; Lai, Richard

    2009-01-01

    Two single-stage InP heterojunction bipolar transistor (HBT) amplifiers operate at 184 and 255 GHz, using Northrop Grumman Corporation s InP HBT MMIC (monolithic microwave integrated circuit) technology. At the time of this reporting, these are reported to be the highest HBT amplifiers ever created. The purpose of the amplifier design is to evaluate the technology capability for high-frequency designs and verify the model for future development work.

  13. White light emission and effect of annealing on the Ho3+–Yb3+ codoped BaCa2Al8O15 phosphor

    International Nuclear Information System (INIS)

    Kumari, Astha; Rai, Vineet Kumar

    2015-01-01

    Graphical abstract: The upconversion emission spectra of the Ho 3+ /Yb 3+ doped/codoped BaCa 2 Al 8 O 15 phosphors with different doping concentrations of Ho 3+ /Yb 3+ ions along with UC emission spectrum of the white light emitting phosphor annealed at 800 °C. - Highlights: • BaCa 2 Al 8 O 15 phosphors codoped with Ho 3+ –Yb 3+ have been prepared by combustion method. • Phosphor annealed at 800 °C, illuminate an intense white light upon NIR excitation. • The sample annealed at higher temperatures emits in the pure green region. • The colour emitted persists in the white region even at high pump power density. • Developed phosphor is suitable for making upconverters and WLEDs. - Abstract: The BaCa 2 Al 8 O 15 (BCAO) phosphors codoped with suitable Ho 3+ –Yb 3+ dopant concentration prepared by combustion method illuminate an intense white light upon near infrared diode laser excitation. The structural analysis of the phosphors and the detection of impurity contents have been performed by using the X-Ray Diffraction, FESEM and FTIR analysis. The purity of white light emitted from the sample has been confirmed by the CIE chromaticity diagram. Also, the white light emitted from the sample persists with the variation of pump power density. The phosphors emit upconversion (UC) emission bands in the blue, green and red region (three primary colours required for white light emission) along with one more band in the near infrared region of the electromagnetic spectrum. On annealing the white light emitting sample at higher temperatures, the sample starts to emit green colour and also the intensity of green and red UC emission bands get enhanced largely.

  14. Porous InP as piezoelectric matrix material in 1-3 magnetoelectric composite sensors

    International Nuclear Information System (INIS)

    Gerngross, M.-D.; Leisner, M.; Carstensen, J.; Foell, H.

    2011-01-01

    This work shows the results of the fabrication of semi-insulating piezoelectric porous InP structures by electrochemical etching and subsequent purely chemical post-etching in an isotropic HF, HNO 3 , EtOH and HAc containing electrolyte. The piezoelectric modulus d 14 of porous InP is measured to around |60| pm / V, which larger by a factor of 30 compared to bulk InP.

  15. Persistent luminescence in both first and second biological windows in ZnGa2O4:Cr3+,Yb3+ glass ceramics

    Science.gov (United States)

    Castaing, V.; Sontakke, A. D.; Xu, J.; Fernández-Carrión, A. J.; Allix, M.; Tanabe, S.; Viana, B.

    2018-02-01

    ZnGa2O4:Cr3+ is an optical material well known for its deep red persistent luminescence properties which are centered in the first biological window. In this work, Yb3+, Cr3+ co-doped zinc gallate oxide has been prepared in the form of glass-ceramics. The studied samples have been elaborated via conventional melt quenching process leading to nanometer scale phase separated glass which was subsequently crystallized to obtain nanocrystals embedded in a transparent glass matrix. In these as-prepared ZnGa2O4:Cr3+,Yb3+ glass-ceramics, regular Cr3+ emission (at around 695 nm) as well as Yb3+ emission (between 950 and 1100 nm) is observed. Several photoluminescence emission and excitation experiments have been recorded in order clarify (i) the simultaneous emission of these cations in different optical windows and (ii) the energy transfer process between these two emitting centers. Further studies proved that Yb3+ is not only active in photoluminescence but also in persistent luminescence, leading to a material demonstrating persistent luminescence properties in both first and second biological windows (650-950 and 1000-1350 nm respectively). Thermoluminescence experiments have been carried out on these materials in order to gain deeper information about the persistent luminescence process.

  16. Hydrogen Passivation of Interstitial Zn Defects in Heteroepitaxial InP Cell Structures and Influence on Device Characteristics

    Science.gov (United States)

    Ringel, S. A.; Chatterjee, B.

    2004-01-01

    Hydrogen passivation of heteroepitaxial InP solar cells is of recent interest for deactivation of dislocations and other defects caused by the cell/substrate lattice mismatch that currently limit the photovoltaic performance of these devices. In this paper we present strong evidence that, in addition to direct hydrogen-dislocation interactions, hydrogen forms complexes with the high concentration of interstitial Zn defects present within the p(+) Zn-doped emitter of MOCVD-grown heteroepitaxial InP devices, resulting in a dramatic increase of the forward bias turn-on voltage by as much as 280 mV, from 680 mV to 960 mV. This shift is reproducible and thermally reversible and no such effect is observed for either n(+)p structures or homoepitaxial p(+)n structures grown under identical conditions. A combination of photoluminescence (PL), electrochemical C-V dopant profiling, SIMS and I-V measurements were performed on a set of samples having undergone a matrix of hydrogenation and post-hydrogenation annealing conditions to investigate the source of this voltage enhancement and confirm the expected role of interstitial Zn and hydrogen. A precise correlation between all measurements is demonstrated which indicates that Zn interstitials within the p(+) emitter and their interaction with hydrogen are indeed responsible for this device behavior.

  17. The temperature dependence of 1/f noise in InP

    NARCIS (Netherlands)

    Chen, X.Y.; Hooge, F.N.; Leijs, M.R.

    1997-01-01

    Noise spectra were measured on CBE grown InP samples in the frequency range from 1 Hz to 104 kHz at temperatures from 77 to 500 K. The experimental results show that llfnoise stems from the lattice scattering. The 1/f noise in InP is well characterised by a parameter CtL~,, in this temperature

  18. Electrochemical formation of InP porous nanostructures and its application to amperometric chemical sensors

    International Nuclear Information System (INIS)

    Sato, Taketomo; Mizohata, Akinori; Fujino, Toshiyuki; Hashizume, Tamotsu

    2008-01-01

    In this paper, we report the electrochemical formation of the InP porous nanostructures and their feasibility for the application to the amperometric chemical sensors. Our two step electrochemical process consists of the pore formation on a (001) n-type InP substrate and the subsequent etching of pore walls caused by changing the polarity of the InP electrode in a HCl-based electrolyte. By applying the anodic bias to the InP electrode, the high-density array of uniform nanopores was formed on the surface. Next, the cathodic bias was applied to the porous sample to reduce the wall thickness by cathodic decomposition of InP, where the thickness of InP nanowall decreased uniformly along the entire depth of the porous layer. From the amperometric measurements of the porous electrode, it was found that the electrocatalytic activity was much higher than that of the planar electrode. Furthermore, the current sensitivity for the H 2 O 2 detection was much enhanced after the cathodic decomposition process. The InP porous nanostructure formed by the present process is one of the promising structures for the application to the semiconductor-based bio/chemical sensors. (copyright 2008 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

  19. Synthesis of NaLuF4:Er3+, Yb3+, Ce3+ nanoparticles and study of photoluminescent properties in C - band

    Directory of Open Access Journals (Sweden)

    Khaydukov K.V.

    2017-01-01

    Full Text Available The novel core@shell nanocrystals β-NaLuF4@NaLuF4 co-doped with rare-earth ions Er3+, Yb3+, Ce3+ have been synthesized. The nano-particles indicate the intensive lines of anti-Stokes luminescence in the telecommunication С - band of spectrum when pumped at 970-980 nm. The nanoparticles have been characterized by transmission electron microscopy and spectrofluorimetry. The nanoparticles have a size 40-80 nm and possess the intensive photo-luminescence 73 nm bandwidth centered around 1530 nm. The photo-luminescence kinetics of β-NaLuF4: Er3+/ Yb3+/ Ce3+ has been studied in IR range of spectrum. We have demonstrated that doping with cerium ions prevents serial stepwise excitation of erbium ions. Consequently, the lifetime of transition in erbium 4I13/2→4I15/2 has risen up to 6.9 ms. Intensity of 1530 nm line in Er3+ ions excited at 980 nm has been increased up to 6 times. Therefore, the nanoparticles are applicable to fabrication of compact waveguide amplifiers for C - band.

  20. A near-infrared luminescent Mn2+-doped NaYF4:Yb,Tm/Fe3+ upconversion nanoparticles redox reaction system for the detection of GSH/Cys/AA.

    Science.gov (United States)

    Zhang, Liping; Ling, Bo; Wang, Lun; Chen, Hongqi

    2017-09-01

    An upconversion luminescence method was developed for the determination of glutathione (GSH), L-cysteine (Cys) or L-ascorbic acid (AA) based on redox reaction. We synthesized poly(acrylic acid) (PAA)-modified Mn 2+ -doped NaYF 4 :Yb,Tm upconversion nanoparticles (UCNPs), and the luminescence of these UCNPs was effectively quenched due to their carboxyl groups coordinating with Fe 3+ to form a UCNPs/Fe 3+ system. GSH, Cys or AA reduced Fe 3+ to Fe 2+ , which induced the luminescence recovery of the UCNPs. Under the optimized conditions, wide linear concentration ranges from 0.25-300μM for GSH, 0.5-875μM for Cys and 0.5-350μM for AA were found, and the detection limits (3S/K) were 0.2μM, 0.5μM and 0.2μM, respectively. Thus, the UCNPs/Fe 3+ system was successfully applied for sensing GSH, Cys or AA. Copyright © 2017 Elsevier B.V. All rights reserved.

  1. Cladding-pumped Yb-doped fiber laser with vortex output beam

    OpenAIRE

    Lin, Di; Clarkson, William

    2015-01-01

    A simple technique for selectively generating a donut-shaped LP11 mode with vortex phase front in a cladding-pumped ytterbium-doped fiber laser is reported. The laser yielded 36W of output with a slope efficiency of 74%.

  2. An improved large signal model of InP HEMTs

    Science.gov (United States)

    Li, Tianhao; Li, Wenjun; Liu, Jun

    2018-05-01

    An improved large signal model for InP HEMTs is proposed in this paper. The channel current and charge model equations are constructed based on the Angelov model equations. Both the equations for channel current and gate charge models were all continuous and high order drivable, and the proposed gate charge model satisfied the charge conservation. For the strong leakage induced barrier reduction effect of InP HEMTs, the Angelov current model equations are improved. The channel current model could fit DC performance of devices. A 2 × 25 μm × 70 nm InP HEMT device is used to demonstrate the extraction and validation of the model, in which the model has predicted the DC I–V, C–V and bias related S parameters accurately. Project supported by the National Natural Science Foundation of China (No. 61331006).

  3. Workshop on Heteroepitaxial InP Solar Cells

    Science.gov (United States)

    Weinberg, I.; Walters, R. W.

    1993-01-01

    In a generic sense, the justification for any sort of InP solar cell research applies, i.e. to take advantage of the inherently high radiation resistance and efficiency of InP solar cells. To be more specific, the approach is justified by its potential for significant cost reduction and the availability of greatly increased cell area afforded by substrates such as Si and Ge. The use of substrates, such as the latter two, would result in increased ruggedness, ease of handling, and improved manufacturability. The use of more rugged substrates would lead to a greatly increased capability for cell thinning leading to the desirable feature of reduced array weight.

  4. Wafer-scale self-organized InP nanopillars with controlled orientation for photovoltaic devices

    International Nuclear Information System (INIS)

    Sanatinia, Reza; Berrier, Audrey; Anand, Srinivasan; Dhaka, Veer; Perros, Alexander P; Huhtio, Teppo; Lipsanen, Harri

    2015-01-01

    A unique wafer-scale self-organization process for generation of InP nanopillars is demonstrated, which is based on maskless ion-beam etching (IBE) of InP developed to obtain the nanopillars, where the height, shape, and orientation of the nanopillars can be varied by controlling the processing parameters. The fabricated InP nanopillars exhibit broadband suppression of the reflectance, ‘black InP,’ a property useful for solar cells. The realization of a conformal p–n junction for carrier collection, in the fabricated solar cells, is achieved by a metalorganic vapor phase epitaxy (MOVPE) overgrowth step on the fabricated pillars. The conformal overgrowth retains the broadband anti-reflection property of the InP nanopillars, indicating the feasibility of this technology for solar cells. Surface passivation of the formed InP nanopillars using sulfur-oleylamine solution resulted in improved solar-cell characteristics. An open-circuit voltage of 0.71 V and an increase of 0.13 V compared to the unpassivated device were achieved. (paper)

  5. Wurtzite-Phased InP Micropillars Grown on Silicon with Low Surface Recombination Velocity.

    Science.gov (United States)

    Li, Kun; Ng, Kar Wei; Tran, Thai-Truong D; Sun, Hao; Lu, Fanglu; Chang-Hasnain, Connie J

    2015-11-11

    The direct growth of III-V nanostructures on silicon has shown great promise in the integration of optoelectronics with silicon-based technologies. Our previous work showed that scaling up nanostructures to microsize while maintaining high quality heterogeneous integration opens a pathway toward a complete photonic integrated circuit and high-efficiency cost-effective solar cells. In this paper, we present a thorough material study of novel metastable InP micropillars monolithically grown on silicon, focusing on two enabling aspects of this technology-the stress relaxation mechanism at the heterogeneous interface and the microstructure surface quality. Aberration-corrected transmission electron microscopy studies show that InP grows directly on silicon without any amorphous layer in between. A set of periodic dislocations was found at the heterointerface, relaxing the 8% lattice mismatch between InP and Si. Single crystalline InP therefore can grow on top of the fully relaxed template, yielding high-quality micropillars with diameters expanding beyond 1 μm. An interesting power-dependence trend of carrier recombination lifetimes was captured for these InP micropillars at room temperature, for the first time for micro/nanostructures. By simply combining internal quantum efficiency with carrier lifetime, we revealed the recombination dynamics of nonradiative and radiative portions separately. A very low surface recombination velocity of 1.1 × 10(3) cm/sec was obtained. In addition, we experimentally estimated the radiative recombination B coefficient of 2.0 × 10(-10) cm(3)/sec for pure wurtzite-phased InP. These values are comparable with those obtained from InP bulk. Exceeding the limits of conventional nanowires, our InP micropillars combine the strengths of both nanostructures and bulk materials and will provide an avenue in heterogeneous integration of III-V semiconductor materials onto silicon platforms.

  6. Oxidation of InP nanowires: a first principles molecular dynamics study.

    Science.gov (United States)

    Berwanger, Mailing; Schoenhalz, Aline L; Dos Santos, Cláudia L; Piquini, Paulo

    2016-11-16

    InP nanowires are candidates for optoelectronic applications, and as protective capping layers of III-V core-shell nanowires. Their surfaces are oxidized under ambient conditions which affects the nanowire physical properties. The majority of theoretical studies of InP nanowires, however, do not take into account the oxide layer at their surfaces. In this work we use first principles molecular dynamics electronic structure calculations to study the first steps in the oxidation process of a non-saturated InP nanowire surface as well as the properties of an already oxidized surface of an InP nanowire. Our calculations show that the O 2 molecules dissociate through several mechanisms, resulting in incorporation of O atoms into the surface layers. The results confirm the experimental observation that the oxidized layers become amorphous but the non-oxidized core layers remain crystalline. Oxygen related bonds at the oxidized layers introduce defective levels at the band gap region, with greater contributions from defects involving In-O and P-O bonds.

  7. Level Densities and Radiative Strength Functions in 170,171Yb

    International Nuclear Information System (INIS)

    Agvaanluvsan, U.; Schiller, A.; Becker, J.A.; Berstein, L.A.; Guttormsen, M.; Mitchell, G.E.; Rekstad, J.; Siem, S.; Voinov, A.

    2003-01-01

    Level densities and radiative strength functions in 171 Yb and 170 Yb nuclei have been measured with the 171 Yb( 3 He, 3 He(prime) γ) 171 Yb and 171 Yb( 3 He, αγ) 170 Yb reactions. A simultaneous determination of the nuclear level density and the radiative strength function was made. The present data adds to and is consistent with previous results for several other rare earth nuclei. The method will be briefly reviewed and the result from the analysis will be presented. The radiative strength function for 171 Yb is compared to previously published work.

  8. Ultraviolet photoluminescence in Gd-doped silica and phosphosilicate fibers

    Directory of Open Access Journals (Sweden)

    Y. Wang

    2017-04-01

    Full Text Available Optical fiber lasers operating in the near infrared and visible spectral regions have relied on the spectroscopic properties of rare earth ions such as Yb3+, Er3+, Tm3+, Nd3+, and Sm3+. Here, we investigate Gd3+ doping in phosphosilicate and pure silica fibers using solution doping and sol-gel techniques, respectively, for potential applications in the ultraviolet. Photoluminescence spectra for optical fiber bundles and fiber preforms were recorded and compared. Emissions at 312 nm (phosphosilicate and 314 nm (pure silica were observed when pumping to the Gd3+ 6DJ, 6IJ, and 6PJ = 5/2, 3/2 energy levels. Oxygen deficient center was observed in solution doping sample with a wide absorption band centered at around 248 nm not affecting pumping to 6IJ states.

  9. A high-coverage nanoparticle monolayer for the fabrication of a subwavelength structure on InP substrates.

    Science.gov (United States)

    Kim, Dae-Seon; Park, Min-Su; Jang, Jae-Hyung

    2011-08-01

    Subwavelength structures (SWSs) were fabricated on the Indium Phosphide (InP) substrate by utilizing the confined convective self-assembly (CCSA) method followed by reactive ion etching (RIE). The surface condition of the InP substrate was changed by depositing a 30-nm-thick SiO2 layer and subsequently treating the surface with O2 plasma to achieve better surface coverage. The surface coverage of nanoparticle monolayer reached 90% by using O2 plasma-treated SiO2/InP substrate among three kinds of starting substrates such as the bare InP, SiO2/InP and O2 plasma-treated SiO2/InP substrate. A nanoparticle monolayer consisting of polystyrene spheres with diameter of 300 nm was used as an etch mask for transferring a two-dimensional periodic pattern onto the InP substrate. The fabricated conical SWS with an aspect ratio of 1.25 on the O2 plasma-treated SiO2/InP substrate exhibited the lowest reflectance. The average reflectance of the conical SWS was 5.84% in a spectral range between 200 and 900 nm under the normal incident angle.

  10. Substitution studies of Mn and Fe in Ln{sub 6}W{sub 4}Al{sub 43} (Ln=Gd, Yb) and the structure of Yb{sub 6}Ti{sub 4}Al{sub 43}

    Energy Technology Data Exchange (ETDEWEB)

    Treadwell, LaRico J.; Watkins-Curry, Pilanda [Department of Chemistry, Louisiana State University, Baton Rouge, LA 70803 (United States); Department of Chemistry, University of Texas at Dallas, Richardson, TX 75080 (United States); McAlpin, Jacob D. [Department of Chemistry, Louisiana State University, Baton Rouge, LA 70803 (United States); Prestigiacomo, Joseph; Stadler, Shane [Department of Physics and Astronomy, Louisiana State University, Baton Rouge, LA 70803 (United States); Chan, Julia Y., E-mail: Julia.Chan@utdallas.edu [Department of Chemistry, Louisiana State University, Baton Rouge, LA 70803 (United States); Department of Chemistry, University of Texas at Dallas, Richardson, TX 75080 (United States)

    2014-02-15

    The synthesis and characterization of Mn- and Fe-substituted Ln{sub 6}W{sub 4}Al{sub 43} (Ln=Gd, Yb) and Yb{sub 6}Ti{sub 4}Al{sub 43} are reported. The compounds adopt the Ho{sub 6}Mo{sub 4}Al{sub 43} structure type with lattice parameters of a∼11 Å and c∼17.8 Å with structural site preferences for Mn and Fe. The magnetization of Yb{sub 6}W{sub 4}Al{sub 43} is sensitive to Mn and Fe doping, which is evident by an increase in the field dependent magnetization. Gd{sub 6}W{sub 4}Al{sub 43}, Gd{sub 6}W{sub 4}Al{sub 42.31(11)}Mn{sub 0.69(11)}, and Gd{sub 6}W{sub 4}Al{sub 41.69(12)}Fe{sub 1.30(12)} order antiferromagnetically in the ab- and c-directions at 15, 14, and 13 K, respectively, with positive Weiss constants, suggesting the presence of ferromagnetic exchange interactions. Anisotropic magnetization data of Gd{sub 6}W{sub 4}Al{sub 43−y}T{sub y} (T=Mn, Fe) analogs are discussed. - Graphical abstract: The magnetic susceptibility of Ln{sub 6}W{sub 4−x}Al{sub 43−y}T{sub x+y} (Ln = Gd, Yb; T= Mn, Fe). Display Omitted - Highlights: • Single crystals of Ln{sub 6}W{sub 4−x}Al{sub 43−y}T{sub x+y} were grown with Al-flux. • Anisotropic magnetic behavior were determined on single crystals. • Gd{sub 6}W{sub 4−x}Al{sub 43−y}T{sub x+y} (T=Mn, Fe) analogs order antiferromagnetically.

  11. Spectral properties of hydrothermally-grown Nd:LuAG, Yb:LuAG, and Yb:Lu{sub 2}O{sub 3} laser materials

    Energy Technology Data Exchange (ETDEWEB)

    Brown, David C., E-mail: DBrown@snakecreeklasers.com [Snake Creek Lasers LLC, Friendsville, PA 18818 (United States); McMillen, Colin D.; Moore, Cheryl; Kolis, Joseph W. [Department of Chemistry and Center for Optical Materials Science and Engineering Technologies, Clemson University, Clemson, SC 29634-0973 (United States); Envid, Victoria [Snake Creek Lasers LLC, Friendsville, PA 18818 (United States)

    2014-04-15

    We have investigated the hydrothermal growth of, and spectrally characterized, the lutetium based laser materials Nd:LuAG, Yb:LuAG, and Yb:Lu{sub 2}O{sub 3}. Absorption cross-section data are presented for Nd:LuAG at 83, 175, and 295 K. Absorption cross-section data was also obtained for Yb:LuAG at 83, 175, and 295 K; the 295 K data was used to generate emission cross-sections using the method of reciprocity. For Yb:Lu{sub 2}O{sub 3}, we present absorption cross-sections at 295 K as well as emission cross-sections derived using reciprocity. -- Highlights: • We present spectral properties for hydrothermally-grown laser crystals. • Absorption cross-section data are presented for Nd:LuAG and Yb:LuAG at 83, 175, and 295 K. • Emission cross-sections are presented for Yb:LuAG at 295 K derived by reciprocity. • We present absorption cross-sections at 295 K as well as emission cross-sections derived using reciprocity for the laser material Yb:Lu{sub 2}O{sub 3}.

  12. Tumor protein 53-induced nuclear protein 1 (TP53INP1 enhances p53 function and represses tumorigenesis

    Directory of Open Access Journals (Sweden)

    Jeyran eShahbazi

    2013-05-01

    Full Text Available Tumor protein 53-induced nuclear protein 1 (TP53INP1 is a stress-induced p53 target gene whose expression is modulated by transcription factors such as p53, p73 and E2F1. TP53INP1 gene encodes two isoforms of TP53INP1 proteins, TP53INP1α and TP53INP1β, both of which appear to be key elements in p53 function. When associated with homeodomain-interacting protein kinase-2 (HIPK2, TP53INP1 phosphorylates p53 protein at Serine 46, enhances p53 protein stability and its transcriptional activity, leading to transcriptional activation of p53 target genes such as p21, PIG-3 and MDM2, cell growth arrest and apoptosis upon DNA damage stress. The anti-proliferative and pro-apoptotic activities of TP53INP1 indicate that TP53INP1 has an important role in cellular homeostasis and DNA damage response. Deficiency in TP53INP1 expression results in increased tumorigenesis; while TP53INP1 expression is repressed during early stages of cancer by factors such as miR-155. This review aims to summarize the roles of TP53INP1 in blocking tumor progression through p53-dependant and p53-independent pathways, as well as the elements which repress TP53INP1 expression, hence highlighting its potential as a therapeutic target in cancer treatment.

  13. Broadened band C-telecom and intense upconversion emission of Er{sup 3+}/Yb{sup 3+} co-doped CaYAlO{sub 4} luminescent material obtained by an easy route

    Energy Technology Data Exchange (ETDEWEB)

    Perrella, R.V.; Schiavon, M.A. [Grupo de Pesquisa em Química de Materiais – (GPQM), Departamento de Ciências Naturais, Universidade Federal de São João del Rei (UFSJ), Campus Dom Bosco, Praça Dom Helvécio, 74, 36301-160 São João del Rei, MG (Brazil); Pecoraro, E.; Ribeiro, S.J.L. [UNESP, Institute of Chemistry, P.O. Box 355, 14800-970 Araraquara, SP (Brazil); Ferrari, J.L., E-mail: ferrari@ufsj.edu.br [Grupo de Pesquisa em Química de Materiais – (GPQM), Departamento de Ciências Naturais, Universidade Federal de São João del Rei (UFSJ), Campus Dom Bosco, Praça Dom Helvécio, 74, 36301-160 São João del Rei, MG (Brazil)

    2016-10-15

    This work reports on photoluminescence properties of Er{sup 3+}/Yb{sup 3+} co-doped CaYAlO{sub 4} in powder form, synthesized by an easy route using citric acid as ligand to form complex precursor. The 1.2 mol% of Yb{sup 3+} was fixed, while the amount of Er{sup 3+} changed in 0.5, 1.5 and 3 mol% in order to evaluate the photoluminescence properties as a function of the Er{sup 3+} concentration. The structural and thermal properties of the viscous solutions and powder materials obtained after the heat-treatment at 1000, 1100 and 1200 °C for 4 h were evaluated by XRD, FTIR and TG/DTA analysis. The results showed the formation of pure CaYAlO{sub 4} tetragonal crystalline phase after heat-treatment at 1100 °C and 1200 °C. Intense emission in the visible region under excitation at 980 nm was attributed to upconversion process, from Er{sup 3+} intra-configurational f–f transitions. The emissions were assigned to the transitions {sup 2}H{sub 11/2}→{sup 4}I{sub 15/2} and {sup 4}S{sub 3/2}→{sup 4}I{sub 15/2} (green region), and {sup 4}F{sub 9/2}→{sup 4}I{sub 15/2} (red region) energy levels. The ratio between emission band integrated areas assigned to the red and green emissions increased as a function of Er{sup 3+} concentration. Under excitation at 980 nm with 100 mW of power pump, the materials also showed intense and broadening emission with maximum at 1520 nm with FWHM of 84.74 nm for the sample CaYAlO{sub 4}:1.5% Er{sup 3+}/1.2% Yb{sup 3+} heat-treated at 1000 °C for 4 h. The photoluminescence properties showed that these materials are promising for use in C-telecom band as optical amplifier biological marker or/and solid-state laser devices under excitation at 980 nm.

  14. Study of the production of 177Lu through 176Yb (n, γ) 177Yb → 177Lu nuclear reaction

    International Nuclear Information System (INIS)

    Silva, Giovana Pasqualini da; Osso Junior, Joao Alberto

    2007-01-01

    The beta minus emitter 177 Lu is a promising therapeutic radioisotope for the curative treatment of cancer using labelled proteins. It has a half - life of T 1/2 = 6.71 day and maximum and average β - energies of 421 and 133 keV, resulting in a short range of radiation in tissue. The decay is accompanied by the emission of low energy γ-radiation with 208.3 keV (11%) and 113 keV (6.4%) suitable for simultaneous imaging, 177 Lu can be produced by two different routes, namely, by irradiation of natural Lu 2 O 3 target ( 176 Lu, 2.6%) or enriched (in 176 Lu) Lu 2 O 3 target, as also by irradiation of Yb target (Yb 2 O 3 ) followed by radiochemical separation of 177 Lu from Yb isotopes. The objective of this work is to study the production of 177 Lu through the indirect 176 Yb(n,γ) 177 Yb → 177 Lu nuclear reaction. The results of the production yield of 177 Lu will be shown and compared with the direct reaction. The method of choice for the chemical separation between Lu and Yb was the ion exchange, using an cation exchange resin in Cl - form and α-HIBA as eluent. Preliminary results showed a good separation of 177 Lu from Yb 2 O 3 indirect targets. (author)

  15. Vaporization thermodynamics of Pd-rich intermediate phases in the Pd–Yb system

    Energy Technology Data Exchange (ETDEWEB)

    Ciccioli, A., E-mail: andrea.ciccioli@uniroma1.it [Dipartimento di Chimica, Sapienza Università di Roma, p.le Aldo Moro 5, 00185 Roma (Italy); Balducci, G.; Gigli, G. [Dipartimento di Chimica, Sapienza Università di Roma, p.le Aldo Moro 5, 00185 Roma (Italy); Provino, A. [Dipartimento di Chimica e Chimica Industriale, Università degli Studi di Genova, via Dodecaneso 31, 16146 Genova (Italy); Istituto SPIN-CNR, Corso Perrone 24, 16152 Genova (Italy); Palenzona, A. [Dipartimento di Chimica e Chimica Industriale, Università degli Studi di Genova, via Dodecaneso 31, 16146 Genova (Italy); Manfrinetti, P. [Dipartimento di Chimica e Chimica Industriale, Università degli Studi di Genova, via Dodecaneso 31, 16146 Genova (Italy); Istituto SPIN-CNR, Corso Perrone 24, 16152 Genova (Italy)

    2016-02-20

    Highlights: • Vaporization equilibria of Pd–Yb intermediate phases investigated by effusion techniques. • Heats of formation of Pd–Yb compounds determined from decomposition/atomization enthalpies. • Phase diagram of the Pd–Yb system re-drawn. • Influence of the Yb valence state on the thermodynamic properties observed. - Abstract: The vaporization thermodynamics of several intermediate phases in the Pd–Yb system was investigated by means of vaporization experiments performed under Knudsen conditions (KEML, Knudsen Effusion Mass Loss). The following thermal decomposition processes were studied in the overall temperature range 819–1240 K and their enthalpy changes determined: 4 PdYb(s) = Pd{sub 4}Yb{sub 3}(s) + Yb(g); 5/3 Pd{sub 4}Yb{sub 3}(s) = 4/3 Pd{sub 5}Yb{sub 3}(s) + Yb(g); 21/13 Pd{sub 5}Yb{sub 3}(s) = 5/13 Pd{sub 21}Yb{sub 10}(s) + Yb(g); 1/3 Pd{sub 21}Yb{sub 10}(s) = 21/9 Pd{sub 3}Yb(s) + Yb(g). Additional measurements were performed by KEMS (Knudsen Effusion Mass Spectrometry) on a Pd-rich two-phase sample, which allowed to detect both Yb(g) and Pd(g) in the vapor phase and to determine the atomization enthalpy of the Pd{sub 3}Yb phase (Pd-rich composition boundary, Pd{sub 3.08}Yb{sub 0.92}): Pd{sub 3.08}Yb{sub 0.92}(s) = 0.92 Yb(g) + 3.08 Pd(g). The enthalpy of formation of this compound was thereafter determined as −68 ± 2 kJ/mol at. and, by combining this value with the decomposition enthalpies derived by KEML, the enthalpies of formation of the studied Pd–Yb intermediate phases were evaluated (kJ/mol at.): −75 ± 4 (Pd{sub 21}Yb{sub 10}), −75 ± 3 (Pd{sub 5}Yb{sub 3}), −73 ± 3 (Pd{sub 4}Yb{sub 3}), and −66 ± 3 (PdYb). A modified version of the Pd–Yb phase diagram is also reported, re-drawn on the basis of literature data and of new experimental information recently become available.

  16. Amorphization and recrystallization in MeV ion implanted InP crystals

    International Nuclear Information System (INIS)

    Xiong, F.; Nieh, C.W.; Jamieson, D.N.; Vreeland, T. Jr.; Tombrello, T.A.

    1988-01-01

    A comprehensive study of MeV- 15 N-ion-implanted InP by a variety of analytical techniques has revealed the physical processes involved in MeV ion implantation into III-V compound semiconductors as well as the influence of post-implantation annealing. It provides a coherent picture of implant distribution, structural transition, crystalline damage, and lattice strain in InP crystals induced by ion implantation and thermal annealing. The experimental results from the different measurements are summarized in this report. Mechanisms of amorphization by implantation and recrystallization through annealing in MeV-ion-implanted InP are proposed and discussed in light of the results obtained

  17. Radiative transition, local field enhancement and energy transfer microcosmic mechanism of tellurite glasses containing Er3+, Yb3+ ions and Ag nanoparticles

    International Nuclear Information System (INIS)

    Zhang, Wenjun; Lin, Jian; Cheng, Mingzhao; Zhang, Shuo; Jia, Yujie; Zhao, Junhong

    2015-01-01

    Er 3+ -doped, Er 3+ /Yb 3+ co-doped tellurite glass with and without Ag NPs were synthesized by melt-quenching method. The high resolution transmission electron microscopy (HR-TEM) and selected area electron diffractions (SAED) manifest growth of Ag NPs. The UV–vis–NIR absorption spectroscopy and fluorescence spectroscopy were measured. The optical band gap and multiphonon relaxation rate constants were calculated. The electronic band structure and local density of state (DOS) of Ag NPs are calculated. The fluorescence emission and enhancement mechanism including localized surface plasmon resonance (LSPR) and energy transfer (ET) microcosmic mechanism were discussed. The electric field distributions of Ag NPs are emulated by FDTD solutions software. Local field enhancement (LFE) induced by LSPR and lightning rod effect was found to be responsible for the fluorescence enhancement while energy transfer from Ag NPs to rare-earth was considered ignorable in the samples without photoluminescent emission. - Highlights: • Tellurite glasses containing Er 3+ , Yb 3+ and Ag NPs are prepared. • Judd–Ofelt and multiphonon relaxation are calculated. • The electronic band structures of Ag NPs are calculated. • The energy transfer mechanism is discussed. • The plasmon resonance effect of Ag NPs is discussed

  18. Controllable synthesis and upconversion emission of ultrasmall near-monodisperse lanthanide-doped Sr2LaF7 nanocrystals

    International Nuclear Information System (INIS)

    Mao, Yifu; Ma, Mo; Gong, Lunjun; Xu, Changfu; Ren, Guozhong; Yang, Qibin

    2014-01-01

    Highlights: • Apropos NaOH content facilitates the growth of pure phase Sr 2 LaF 7 NCs. • Yb 3+ doping is favorable to the formation of Sr 2 LaF 7 NCs with uniform size. • Ultrasmall near-monodispersed Sr 2 LaF 7 NCs(sub-10 nm) were synthesized for the first time. • Intense multicolor upconversion can be obtained by properly lanthanide doping. - Abstract: Fluorite phase Sr 2 LaF 7 nanocrystals (NCs) were synthesized via solvothermal method using oleic acid as capping ligands. The effects of preparing conditions on the phase structure, crystal size, morphology, and upconversion (UC) emission properties of the products were studied. The results reveal that just apropos NaOH content facilitates the growth of near-monodispersed pure phase Sr 2 LaF 7 NCs, and Yb 3+ doping is favorable to the formation of pure Sr 2 LaF 7 phase with more uniform size distribution. The average crystalline size of the products can be controlled less than 10 nm. Following appropriate lanthanide ions doping, the NCs show intense blue, yellow, and white-color UC emission under the excitation of a 980 nm laser. The energy transfer UC mechanisms for the fluorescent intensity were also investigated

  19. Optical waveguide formed in Yb:GdCOB and Yb:YCOB crystals by 3.0MeV O{sup +} implantation

    Energy Technology Data Exchange (ETDEWEB)

    Jiao, Yang, E-mail: sdujy@163.com [College of Physics and Electronics, Shandong Normal University, Jinan 250014 (China)

    2013-07-15

    Planar optical waveguides were formed in Yb:GdCOB and Yb:YCOB crystals by 3.0 MeV O{sup +} ion implantation at fluence of 2 × 10{sup 15} ions/cm{sup 2} at room temperature, respectively. The prism coupling method was performed to characterize the dark-mode property of the waveguides. The refractive index profiles in the waveguides were reconstructed by reflectivity calculation method (RCM). The results show that after the implantation, a 1.5 μm-wide region with enhanced refractive-index was formed beneath the sample surfaces to act as waveguide structures for both Yb:GdCOB and Yb:YCOB.

  20. Channeling study of laser-induced defect generation in InP and InAs

    International Nuclear Information System (INIS)

    Burdel', K.K.; Kashkarov, P.K.; Timoshenko, V.Yu.; Chechenin, N.G.

    1992-01-01

    Damage production in InP and InAs single crystals induced by a ruby-laser pulse irradiation with τ p =20 ms in the energy density region W=0.05-1.0 J/cm 2 is studied by the channeling and Rutherford backscattering techniques. The defect generation threshold was determined to be equal to 0.2 J/cm 2 and 0.55 J/cm 2 for InP and InAs crystals, respectively. Stoichiometric defects in InP crystals were observed at W>=0.5 J/cm 2 . The temperature fields in InP and InAs under laser irradiation were calculated. The experimental observations are considered as a result of a selective evaporation of the components from the melt

  1. Spectroscopy and enhanced frequency upconversion in Nd3+-Yb3+ codoped TPO glasses: energy transfer and NIR to visible upconverter

    Science.gov (United States)

    Azam, Mohd; Rai, Vineet Kumar; Mohanty, Deepak Kumar

    2017-09-01

    TeO2-Pb3O4 (TPO) glasses codoped with Nd3+ and Yb3+ ions have been fabricated by conventional melting technique. The absorption, emission and excitation spectra of the samples have been recorded. The optical band gap in both the doped/codoped glasses is found to be ˜3.31 eV. Judd-Ofelt analysis has been carried out by using the absorption spectrum of 0.8 mol% Nd3+ doped glass to determine the radiative properties viz radiative transition probabilities, branching ratios, radiative lifetimes, quality factor and emission cross sections of some emitting levels for Nd3+ ions. The radiative transition probability for the 4G7/2 → 4I9/2 transition (˜1926 Hz) is found to be maximum compared to other 4G5/2 → 4I9/2 (˜1622 Hz) and 4F5/2 → 4I9/2 (˜865 Hz) transitions. Upconversion (UC) luminescence of the samples has been examined by the 980 nm CW diode laser excitation. Effect of addition of Yb3+ ions in the Nd3+ doped glasses on UC emission intensity has been discussed. The UC emission intensity corresponding to the green, red and NIR bands in the codoped glass has been enhanced by ˜17, ˜12 and ˜42 times as compared to that of the Nd3+ singly doped glass. The quantum efficiency for the 4G7/2 level is found to be ˜32%. The nephelauxetic ratio, bonding parameter and covalency of Nd3+ ions have been found positive which represents the covalent bonding between Nd3+ ion and oxygen atom. The colour tunability from yellowish-green to dominant green region has been obtained in the optimized codoped TPO glass.

  2. Enhanced light output from the nano-patterned InP semiconductor substrate through the nanoporous alumina mask.

    Science.gov (United States)

    Jung, Mi; Kim, Jae Hun; Lee, Seok; Jang, Byung Jin; Lee, Woo Young; Oh, Yoo-Mi; Park, Sun-Woo; Woo, Deokha

    2012-07-01

    A significant enhancement in the light output from nano-patterned InP substrate covered with a nanoporous alumina mask was observed. A uniform nanohole array on an InP semiconductor substrate was fabricated by inductively coupled plasma reactive ion etching (ICP-RIE), using the nanoporous alumina mask as a shadow mask. The light output property of the semiconductor substrate was investigated via photoluminescence (PL) intensity measurement. The InP substrate with a nanohole array showed a more enhanced PL intensity compared with the raw InP substrate without a nanohole structure. After ICP-RIE etching, the light output from the nanoporous InP substrate covered with a nanoporous alumina mask showed fourfold enhanced PL intensity compared with the raw InP substrate. These results can be used as a prospective method for increasing the light output efficiency of optoelectronic devices.

  3. Low temperature synthesis of InP nanocrystals

    International Nuclear Information System (INIS)

    Ung Thi Dieu Thuy; Tran Thi Thuong Huyen; Nguyen Quang Liem; Reiss, Peter

    2008-01-01

    We present a simple method for the chemical synthesis of InP nanocrystals, which comprises several advantages: (i) the use of simple reagents, namely InCl 3 .4H 2 O and yellow P as the In and P precursors, respectively, and NaBH 4 as the reducing agent in a mixed solvent of ethanol and toluene; (ii) a short reaction time (1-5 h) and low temperature (<75 deg. C); (iii) a high reaction yield approaching 100%. InP NCs in the zinc-blende structure have been obtained as confirmed by powder X-ray diffraction and Raman scattering measurements. Their mean size of 4 nm has been determined by transmission electron microscopy, Raman scattering and absorption spectroscopy

  4. Efficiency enhancement of InP nanowire solar cells by surface cleaning

    NARCIS (Netherlands)

    Cui, Y.; Wang, J.; Plissard, S.R.; Cavalli, A.; Vu, T.T.T.; Veldhoven, van P.J.; Gao, L.; Trainor, M.J.; Verheijen, M.A.; Haverkort, J.E.M.; Bakkers, E.P.A.M.

    2013-01-01

    We demonstrate an efficiency enhancement of an InP nanowire (NW) axial p–n junction solar cell by cleaning the NW surface. NW arrays were grown with in situ HCl etching on an InP substrate patterned by nanoimprint lithography, and the NWs surfaces were cleaned after growth by piranha etching. We

  5. Enhanced persistent red luminescence in Mn2+-doped (Mg,Zn)GeO3 by electron trap and conduction band engineering

    Science.gov (United States)

    Katayama, Yumiko; Kayumi, Tomohiro; Ueda, Jumpei; Tanabe, Setsuhisa

    2018-05-01

    The effect of Zn substitution on the persistent luminescence properties of MgGeO3:Mn2+-Ln3+ (Ln = Eu and Yb) red phosphors was investigated. The intensity of the persistent luminescence of the Eu3+ co-doped phosphors increased with increasing Zn content, whereas that of the Yb3+ co-doped samples decreased. For both series of lanthanide co-doped samples, the thermoluminescence (TL) glow peak shifted to the lower temperature side with increasing Zn content. These persistent luminescence properties were well explained in terms of lowering of the bottom of the conduction band relative to the ground state of the divalent lanthanide ions. Especially, in Eu3+ co-doped system, TL peak shifted from 520 K to 318 K by 50% Zn substitution. The persistent radiance of the (Mg0.5 Zn0.5)GeO3: Mn2+-Eu3+ sample at 1 h after ceasing UV light was 46 times stronger than that of MgGeO3:Mn2+-Eu3+, and 11 times stronger than that of ZnGa2O4: Cr3+ standard deep red persistent phosphor.

  6. Low energy Ar ion bombardment damage of Si, GaAs, and InP surfaces

    International Nuclear Information System (INIS)

    Williams, R.S.

    1982-01-01

    Argon bombardment damage to (100) surfaces of Si, GaAs, and InP for sputter ion-gun potentials of 1, 2, and 3 kilovolts was studied using Rutherford backscattering. Initial damage rates and saturation damage levels were determined. Bombardment damage sensitivity increased for the sequence Si, GaAs, and InP. Saturation damage levels for Si and GaAs correspond reasonably to LSS projected range plus standard deviation estimates; damage to InP exceeded this level significantly. For an ion-gun potential of 3 keV, the initial sputter yield of P from an InP surface exceeded the sputter yield of In by four atoms per incident Ar projectile. (author)

  7. Utilization of IR laser pumped anti-Stokes emission of Er-Yb doped systems for identification of securities

    International Nuclear Information System (INIS)

    Kuzmin, A.N.; Ryabtsev, G.I.; Ketko, G.A.; Gorelenko, A.Yu.; Demidovich, A.A.; Strek, W.; Maruszewicz, K.; Deren, P.

    1996-01-01

    In this paper we present a utilization of anti-Stokes luminescence of Er-Yb systems for identification of securities. A simple method of detection of an up-conversion phenomenon in such system by means of IR laser operating in the region 960-1010 nm is proposed. (author)

  8. Transport, Thermal, and Magnetic Properties of YbNi3X9 (X = Al, Ga): A Newly Synthesized Yb-Based Kondo Lattice System

    Science.gov (United States)

    Yamashita, Tetsuro; Miyazaki, Ryoichi; Aoki, Yuji; Ohara, Shigeo

    2012-03-01

    We have succeeded in synthesizing a new Yb-based Kondo lattice system, YbNi3X9 (X = Al, Ga). Our study reveals that YbNi3Al9 shows typical features of a heavy-fermion antiferromagnet with a Néel temperature of TN = 3.4 K. All of the properties reflect a competition between the Kondo effect and the crystalline electric field (CEF) effect. The moderate heavy-fermion state leads to an enhanced Sommerfeld coefficient of 100 mJ/(mol\\cdotK2), even if ordered antiferromagnetically. On the other hand, the isostructural gallide YbNi3Ga9 is an intermediate-valence system with a Kondo temperature of TK = 570 K. A large hybridization scale can overcome the CEF splitting energy, and a moderately heavy Fermi-liquid ground state with high local moment degeneracy should form at low temperatures. Note that the quality of single-crystalline YbNi3X9 is extremely high compared with those of other Yb-based Kondo lattice compounds. We conclude that YbNi3X9 is a suitable system for investigating the electronic structure of Yb-based Kondo lattice systems from a heavy-fermion system with an antiferromagnetically ordered ground state to an intermediate-valence system.

  9. Yb-based heavy fermion compounds and field tuned quantum chemistry

    Energy Technology Data Exchange (ETDEWEB)

    Mun, Eundeok [Iowa State Univ., Ames, IA (United States)

    2010-01-01

    The motivation of this dissertation was to advance the study of Yb-based heavy fermion (HF) compounds especially ones related to quantum phase transitions. One of the topics of this work was the investigation of the interaction between the Kondo and crystalline electric field (CEF) energy scales in Yb-based HF systems by means of thermoelectric power (TEP) measurements. In these systems, the Kondo interaction and CEF excitations generally give rise to large anomalies such as maxima in ρ(T) and as minima in S(T). The TEP data were use to determine the evolution of Kondo and CEF energy scales upon varying transition metals for YbT2Zn20 (T = Fe, Ru, Os, Ir, Rh, and Co) compounds and applying magnetic fields for YbAgGe and YbPtBi. For YbT2Zn20 and YbPtBi, the Kondo and CEF energy scales could not be well separated in S(T), presumably because of small CEF level splittings. A similar effect was observed for the magnetic contribution to the resistivity. For YbAgGe, S(T) has been successfully applied to determine the Kondo and CEF energy scales due to the clear separation between the ground state and thermally excited CEF states. The Kondo temperature, TK, inferred from the local maximum in S(T), remains finite as magnetic field increases up to 140 kOe. In this dissertation we have examined the heavy quasi-particle behavior, found near the field tuned AFM quantum critical point (QCP), with YbAgGe and YbPtBi. Although the observed nFL behaviors in the vicinity of the QCP are different between YbAgGe and YbPtBi, the constructed H-T phase diagram including the two crossovers are similar. For both YbAgGe and YbPtBi, the details of the quantum criticality turn out to be complicated. We expect that YbPtBi will provide an additional example of field tuned quantum criticality, but clearly there are further experimental investigations left and more ideas needed to understand the basic physics of field-induced quantum

  10. Magnetic structure of the YbMn2SbBi compound

    International Nuclear Information System (INIS)

    Morozkin, A.V.; Manfrinetti, P.

    2011-01-01

    Graphical abstract: Display Omitted Research highlights: → A neutron diffraction investigation in zero applied field of La 2 O 2 S-type YbMn 2 SbBi shows antiferromagnetic ordering below 138(3) K and ferrimagnetic ordering below 112(3) K. → Between 138 and 112 K, the magnetic structure of YbMn 2 SbBi consists of antiferromagnetically coupled ab-plane magnetic moments of the manganese atoms (D 1d magnetic point group). → Below 112(3) K, the magnetic structure of YbMn 2 SbBi becames the sum antiferromagnetic component with D 1d magnetic point group and ferromagnetic one with C 2 magnetic point group. → The magnitude of Yb and Mn magnetic moments in YbMn 2 SbBi at 2 K (M Yb = 3.6(2) μ B , M Mn = 3.5(2) μ B ) correspond to the trivalent state of the Yb ions and tetravalent state of the Mn ions. - Abstract: A neutron diffraction investigation has been carried out on the trigonal La 2 O 2 S-type (hP5, space group P3-bar ml, No. 164; also CaAl 2 Si 2 -type) YbMn 2 SbBi intermetallic compound. The YbMn 2 SbBi presents antiferromagnetic ordering below 138(3) K and ferrimagnetic ordering below 112(3) K. Between 138 and 112 K, the magnetic structure of YbMn 2 SbBi consists of antiferromagnetically coupled ab-plane magnetic moments of the manganese atoms (D 1d magnetic point group). Below 112(3) K, the ferromagnetic components of Yb and Mn begin to develop, and the magnetic structure of YbMn 2 SbBi becames the sum antiferromagnetic component with D 1d magnetic point group and ferromagnetic one with C 2 magnetic point group. The magnitude of Yb and Mn magnetic moments in YbMn 2 SbBi at 2 K (M Yb = 3.6(2) μ B , M Mn = 3.5(2) μ B ) correspond to the trivalent state of the Yb ions and tetravalent state of the Mn ions.

  11. Comparative modeling of InP solar cell structures

    Science.gov (United States)

    Jain, R. K.; Weinberg, I.; Flood, D. J.

    1991-01-01

    The comparative modeling of p(+)n and n(+)p indium phosphide solar cell structures is studied using a numerical program PC-1D. The optimal design study has predicted that the p(+)n structure offers improved cell efficiencies as compared to n(+)p structure, due to higher open-circuit voltage. The various cell material and process parameters to achieve the maximum cell efficiencies are reported. The effect of some of the cell parameters on InP cell I-V characteristics was studied. The available radiation resistance data on n(+)p and p(+)p InP solar cells are also critically discussed.

  12. A mass spectrometric study of the neutral and ionic vapor components of ytterbium chlorides; formation enthalpies of YbCl2 and YbCl3 molecules, and YbCl3- and YbCl4- ions in the gas phase

    International Nuclear Information System (INIS)

    Kuznetsov, F.Yh.; Kudin, L.S.; Pogrebnoj, A.M.; Butman, M.F.; Burdukovskaya, G.G.

    1997-01-01

    Ionic and neutral components of saturated vapour over the ytterbium di-and trichloride is studied through the Knudsen effusive method with mass-spectromic registration of evaporated products within the temperature range of 1000-1300 K. It is found that ytterbium trichloride is subjected to thermal decomposition with formation of ytterbium dichloride and molecular chloride. Sublimation enthalpy and enthalpy of YbCl 2 and YbCl 3 molecules formation in a gaseous phase at 298 K, comprising 356±6, 293±8, -425±6 and -667±6 kJ/mole correspondingly, are determined with application of 2 and 3 thermodynamical laws. Enthalpies of YbCl 3 - and YbCl 4 - negative ions formation in a gaseous phase at 298 K equal to -895 and -1211±30 kJ/mole correspondingly are calculated by measured equilibrium constants ion-molecular reaction. 30 refs., 3 figs., 3 tabs

  13. Incorporation and conduction of proton in Sr-doped LaMO3 (M=Al, Sc, In, Yb, Y)

    International Nuclear Information System (INIS)

    Okuyama, Yuji; Kozai, Takeshi; Ikeda, Shohei; Matsuka, Maki; Sakai, Takaaki; Matsumoto, Hiroshige

    2014-01-01

    In order to clarify the effect of the B site species in ABO 3 perovskite oxides on the proton transport properties, the proton incorporation into a series of La 0.9 Sr 0.1 MO 3-δ , (M = Al, Sc, In, Yb, Y) was studied by measuring the electrical conductivity and electromotive forces of the gas concentration cells, and by a thermogravimetric analysis. The proton concentration and electrical conductivity increased in the order of the B site species, Al 0.9 Sr 0.1 AlO 3-δ showed an oxide ion conductivity, while La 0.9 Sr 0.1 YbO 3-δ and La 0.9 Sr 0.1 YO 3-δ exhibited a protonic conductivity in the temperature range of 573–1173 K. La 0.9 Sr 0.1 ScO 3-δ and La 0.9 Sr 0.1 InO 3-δ showed a protonic conductivity under 873 K, and a mixed proton and oxide ion conductivity at 1073 K

  14. YB0 SERVICES INSTALLATION COMPLETED

    CERN Document Server

    The beauty of the completed YB0 was briefly visible at P5 as preparations continue for Tracker installation. A tremendous effort, lasting 7 months and involving more than 100 workers on the busiest days, resulted in 5700 electrical cables, 780 optical cables with 65k fibre channels, and 550 pipes laid on YB0 for HB, EB and Tracker.

  15. Optical transitions of Tm3+ in oxyfluoride glasses and compositional and thermal effect on upconversion luminescence of Tm3+/Yb3+-codoped oxyfluoride glasses.

    Science.gov (United States)

    Feng, Li; Wu, Yinsu; Liu, Zhuo; Guo, Tao

    2014-01-24

    Optical properties of Tm(3+)-doped SiO2-BaF2-ZnF2 glasses have been investigated on the basis of the Judd-Ofelt theory. Judd-Ofelt intensity parameters, radiative transition probabilities, fluorescence branching ratios and radiative lifetimes have been calculated for different glass compositions. Upconversion emissions were observed in Tm(3+)/Yb(3+)-codoped SiO2-BaF2-ZnF2 glasses under 980 nm excitation. The effects of composition, concentration of the doping ions, temperature, and excitation pump power on the upconversion emissions were also systematically studied. Copyright © 2013 Elsevier B.V. All rights reserved.

  16. Photoluminescence study of as-grown vertically standing wurtzite InP nanowire ensembles.

    Science.gov (United States)

    Iqbal, Azhar; Beech, Jason P; Anttu, Nicklas; Pistol, Mats-Erik; Samuelson, Lars; Borgström, Magnus T; Yartsev, Arkady

    2013-03-22

    We demonstrate a method that enables the study of photoluminescence of as-grown nanowires on a native substrate by non-destructively suppressing the contribution of substrate photoluminescence. This is achieved by using polarized photo-excitation and photoluminescence and by making an appropriate choice of incident angle of both excitation beam and photoluminescence collection direction. Using TE-polarized excitation at a wavelength of 488 nm at an incident angle of ∼70° we suppress the InP substrate photoluminescence relative to that of the InP nanowires by about 80 times. Consequently, the photoluminescence originating from the nanowires becomes comparable to and easily distinguishable from the substrate photoluminescence. The measured photoluminescence, which peaks at photon energies of ∼1.35 eV and ∼1.49 eV, corresponds to the InP substrate with zinc-blende crystal structure and to the InP nanowires with wurtzite crystal structure, respectively. The photoluminescence quantum yield of the nanowires was found to be ∼20 times lower than that of the InP substrate. The nanowires, grown vertically in a random ensemble, neither exhibit substantial emission polarization selectivity to the axis of the nanowires nor follow excitation polarization preferences observed previously for a single nanowire.

  17. Construction of a system for up-conversion detection in vitroceramics doped with rare earths

    International Nuclear Information System (INIS)

    Santa Cruz, P.A.; Azevedo, W.M. de; Sa, G.F. de

    1983-01-01

    A system capable of detecting up-conversion processes by energy transference or cooperative luminescence was developed. Pulverized vitroceramic samples containing PbF 2 and GeO 2 , doped with Yb 2 O 3 as sensitizer and Tm 2 O 3 or Er 2 O 3 as activator, were used. A diagram of the detection system, as well as graphs showing the variation of the emission intensity of these doped vitroceramics as a function of excitation intensity (970 mn), are presented. (C.L.B.) [pt

  18. Low temperature synthesis of InP nanocrystals

    Energy Technology Data Exchange (ETDEWEB)

    Ung Thi Dieu Thuy [Institute of Materials Science (IMS), Vietnamese Academy of Science and Technology (VAST), 18 Hoang Quoc Viet, Cau Giay, Hanoi (Viet Nam); Tran Thi Thuong Huyen [Institute of Materials Science (IMS), Vietnamese Academy of Science and Technology (VAST), 18 Hoang Quoc Viet, Cau Giay, Hanoi (Viet Nam); National University of Thai Nguyen, 2 Luong Ngoc Quyen, Thai Nguyen (Viet Nam); Nguyen Quang Liem [Institute of Materials Science (IMS), Vietnamese Academy of Science and Technology (VAST), 18 Hoang Quoc Viet, Cau Giay, Hanoi (Viet Nam)], E-mail: liemnq@ims.vast.ac.vn; Reiss, Peter [DSM/INAC/SPrAM, UMR 5819 CEA-CNRS-Universite Joseph Fourier/LEMOH, CEA Grenoble, 17 rue des Martyrs, 38054 Grenoble Cedex 9 (France)

    2008-12-20

    We present a simple method for the chemical synthesis of InP nanocrystals, which comprises several advantages: (i) the use of simple reagents, namely InCl{sub 3}.4H{sub 2}O and yellow P as the In and P precursors, respectively, and NaBH{sub 4} as the reducing agent in a mixed solvent of ethanol and toluene; (ii) a short reaction time (1-5 h) and low temperature (<75 deg. C); (iii) a high reaction yield approaching 100%. InP NCs in the zinc-blende structure have been obtained as confirmed by powder X-ray diffraction and Raman scattering measurements. Their mean size of 4 nm has been determined by transmission electron microscopy, Raman scattering and absorption spectroscopy.

  19. Up-conversion routines of Er{sup 3+}–Yb{sup 3+} doped Y{sub 6}O{sub 5}F{sub 8} and YOF phosphors

    Energy Technology Data Exchange (ETDEWEB)

    Park, Sangmoon, E-mail: spark@silla.ac.kr [Center for Green Fusion Technology and Department of Engineering in Energy & Applied Chemistry, Silla University, Busan 617-736 (Korea, Republic of); Yang, Wonseok; Park, Chu-Young; Noh, Minhee; Choi, Seulki [Center for Green Fusion Technology and Department of Engineering in Energy & Applied Chemistry, Silla University, Busan 617-736 (Korea, Republic of); Park, Dahye; Jang, Ho Seong; Cho, So-Hye [Center for Materials Architecturing, Institute of Multidisciplinary Convergence of Materials, Korea Institute of Science and Technology, Seoul 130-650 (Korea, Republic of)

    2015-11-15

    Highlights: • Single-phase optical materials of Y{sub 6}O{sub 5}F{sub 8}:Er and YOF:Er were prepared. • Effective spectral converting properties were observed in Y{sub 6}O{sub 5}F{sub 8}:Er,Yb. • 980 nm diode laser was irradiated for up-converting analysis. • A multi-photon process in the phosphors was investigated. - Abstract: Optical materials composed of a Y{sub 6(1−p−q)}Er{sub 6p}Yb{sub 6q}O{sub 5}F{sub 8} (p = 0.001–0.1, q = 0.005–0.1) solid solution with Y{sub 0.99}Er{sub 0.01}OF were prepared via a solid-state reaction using excess NH{sub 4}F flux at 950 °C for 30 min. X-ray diffraction patterns of Y{sub 6(1−p−q)}Er{sub 6p}Yb{sub 6q}O{sub 5}F{sub 8} and Y{sub 0.99}Er{sub 0.01}OF were compared upon altering the synthesis temperature and the molar ratio of the NH{sub 4}F flux to the Y{sup 3+} (Er{sup 3+}, Yb{sup 3+}) ions. The effective spectral-conversion properties of Er{sup 3+} and Er{sup 3+}–Yb{sup 3+} ions in Y{sub 6}O{sub 5}F{sub 8} phosphors were monitored during excitation with a 980 nm wavelength diode-laser. Selection of appropriate Er{sup 3+} and/or Yb{sup 3+} concentrations in the Y{sub 6}O{sub 5}F{sub 8} structure led to achievement of the desired up-conversion emission, from the green to the red regions of the spectra. Furthermore, the mechanism of up-conversion in the phosphors was described by an energy-level schematic. Up-conversion emission spectra and the dependence of the emission intensity on pump power (between 193 and 310 mW) in the Y{sub 6(0.995−q)}Er{sub 0.03}Yb{sub 6q}O{sub 5}F{sub 8} phosphors were also investigated.

  20. Identification and characterization of NF-YB family genes in tung tree.

    Science.gov (United States)

    Yang, Susu; Wang, Yangdong; Yin, Hengfu; Guo, Haobo; Gao, Ming; Zhu, Huiping; Chen, Yicun

    2015-12-01

    The NF-YB transcription factor gene family encodes a subunit of the CCAAT box-binding factor (CBF), a highly conserved trimeric activator that strongly binds to the CCAAT box promoter element. Studies on model plants have shown that NF-YB proteins participate in important developmental and physiological processes, but little is known about NF-YB proteins in trees. Here, we identified seven NF-YB transcription factor-encoding genes in Vernicia fordii, an important oilseed tree in China. A phylogenetic analysis separated the genes into two groups; non-LEC1 type (VfNF-YB1, 5, 7, 9, 11, 13) and LEC1-type (VfNF-YB 14). A gene structure analysis showed that VfNF-YB 5 has three introns and the other genes have no introns. The seven VfNF-YB sequences contain highly conserved domains, a disordered region at the N terminus, and two long helix structures at the C terminus. Phylogenetic analyses showed that VfNF-YB family genes are highly homologous to GmNF-YB genes, and many of them are closely related to functionally characterized NF-YBs. In expression analyses of various tissues (root, stem, leaf, and kernel) and the root during pathogen infection, VfNF-YB1, 5, and 11 were dominantly expressed in kernels, and VfNF-YB7 and 9 were expressed only in the root. Different VfNF-YB family genes showed different responses to pathogen infection, suggesting that they play different roles in the pathogen response. Together, these findings represent the first extensive evaluation of the NF-YB family in tung tree and provide a foundation for dissecting the functions of VfNF-YB genes in seed development, stress adaption, fatty acid synthesis, and pathogen response.