Safety and upgrading of nuclear power plants with WWER-440/V-230; Voprosy bezopasnosti i modernizatsii AEhS s WWER-440 (V-230)

Energy Technology Data Exchange (ETDEWEB)

Melnikov, N [Opytno-Konstruktorskoe Byuro Gidropress, Podol` sk (Russian Federation)

1996-12-31

Modernization of WWER-440/V-230 reactors is considered according to the WANO project `Proposal for reconstruction of WWER-440/V-230 reactors` (1990). The main technical measures to be taken relate to: 1. Expanding the considered spectrum of design basis accidents; 2. Provision of first loop integrity; 3. Safety system structure and components reliability enhancement; 4. Reduction o initiating events probability; 5. Enhancement of hermeticity and integrity of the area surrounding the first loop; 6. Fire fighting system upgrade; 7. Radiation control system upgrade; 8. Provision of seismic resistance. Details of the recommended technical steps for some NPPs are presented. 1 tab.

WWER-1000 Burnup Credit Benchmark (CB5)

International Nuclear Information System (INIS)

Manolova, M.A.

2002-01-01

In the paper the specification of WWER-1000 Burnup Credit Benchmark first phase (depletion calculations), given. The second phase - criticality calculations for the WWER-1000 fuel pin cell, will be given after the evaluation of the results, obtained at the first phase. The proposed benchmark is a continuation of the WWER benchmark activities in this field (Author)

Power peak in vicinity of WWER-440 control rod at end of fuel cycle

International Nuclear Information System (INIS)

Mikus, J.

2003-01-01

This paper presents some results of the axial power distribution measurements carried out in a WWER-440 type core on the light-water, zero-power reactor LR-O in the vicinity of the WWER-440 control rod model at zero boron concentration in moderator. Further presented information concern the description of the control rod model, LR-0 core arrangement, specification of the fuel assemblies and measurement conditions. The aim of performed experiment is enlargement of the available 'power peaking database' to enable the calculation codes validation also by means of data that correspond to the end of WWER-440 fuel cycle (Authors)

Control assembly ejection accident analysis for WWER-440 (Armenian NPP)

International Nuclear Information System (INIS)

Bznuni, S.; Malakyan, Ts.; Amirjanyan, A.; Ghasabyan, L.

2007-01-01

Control Assembly ejection in WWER-440 initiated by the loss of integrity of the Control Assemblies drive housing has been analyzed. This event causes a very rapid reactivity insertion to the core and small break LOCA which potentially could lead to rapid power increase and redistribution of heat release in the core resulting in a fuel, cladding and coolant temperature rise; primary pressure increase, radiological consequences due to loss of primary coolant and potential loss of cladding integrity and fuel disintegration (if applicable). Methodology of the analysis is based on conservative assumptions as well as on deterministic approach for selection of functioning logic of systems and equipment's to maximize reactor core power and minimize power decreasing reactivity feedback. Computational analyses were performed by 3D kinetics PARCS-RELAP coupled code. WWER-440 fuel cross-section libraries, diffusion coefficients and kinetics parameters were calculated by HELOS code. In this paper analysis of accident for Hot Full Power was presented. Results of analysis show that ANPP WWER-440 reactor design meets acceptance criteria prescribed for RIA type design based accidents (Authors)

Guidelines for prediction of irradiation embrittlement of operating WWER-440 reactor pressure vessels

International Nuclear Information System (INIS)

2005-06-01

This TECDOC has been developed under an International Atomic Energy Agency Coordinated Research Project (CRP) entitled Evaluation of Radiation Damage of WWER Reactor Pressure Vessels (RPV) using Database on RPV Materials to develop the guidelines for prediction of radiation damage to WWER-440 PRVs. The WWER-440 RPV was designed by OKB Gidropress, Russian Federation, the general designer. Prediction of irradiation embrittlement of RPV materials is usually done in accordance with relevant codes and standards that are based on the large amounts of information from surveillance and research programmes. The existing Russian code (standard for strength calculations of components and piping in NPPs - PNAE G 7-002-86) for the WWER RPV irradiation embrittlement assessment was approved more than twenty years ago and based mostly on the experimental data obtained in research reactors with accelerated irradiation. Nevertheless, it is still in use and generally consistent with new data. The present publication presents the analyses using all available data required for more precise prediction of radiation embrittlement of WWER-440 RPV materials. Based on the fact that it contains a large amount of data from surveillance programmes as well as research programmes, the IAEA International Database on RPV Materials (IDRPVM) is used for the detailed analysis of irradiation embrittlement of WWER RPV materials. Using IDRPVM, the guideline is developed for assessment of irradiation embrittlement of RPV ferritic materials as a result of degradation during operation. Two approaches, i.e. transition temperatures based on Charpy impact notch toughness, as well as based on static fracture toughness tests, are used in RPV integrity evaluation. The objectives of the TECDOC are the analysis of irradiation embrittlement data for WWER- 440 RPV materials using IDRPVM database, evaluation of predictive formulae depending on chemical composition of the material, neutron fluence, flux, and

Information about AER WG A on improvement, extension and validation of parametrized few-group libraries for VVER 440 and VVER 1000

International Nuclear Information System (INIS)

Mikolas, P.

2010-01-01

Joint AER Working Group A on 'Improvement, extension and validation of parameterized few-group libraries for WWER-440 and WWER-1000' and AER Working Group B on 'Core design' nineteenth meeting was hosted by VUJE a. s. in Modra - Harmonia (Slovakia) during the period of 20. to 22. April 2010. There were present altogether 12 participants from 8 member organizations and 9 papers were presented (8 of them in written form). Objectives of the meeting of WG A are: Issues connected with spectral calculations and few-groups libraries preparation, their accuracy and validation. Presentations were devoted to some aspects of transport and diffusion calculations and to the benchmark dealing with WWER-1000 core periphery power tilt. Tamas Parko (co-authors Istvan Pos and Sandor Patai Szabo) described in his presentation 'Application of Discontinuity factors in C-PORCA 7 code', Radoslav Zajac (co-authors Petr Darilek and Vladimir Necas) spoke about 'Fast Reactor Nodalisation in HELIOS Code', Gabriel Farkas presented 'Calculation of Spatial Weighting Functions of Ex-Core Neutron Detectors for WWER-440 Using Monte Carlo Approach' and Daniel Sprinzl (co-authors Vaclav Krysl, Pavel Mikolas and Jiri Svarny) provided a definition of a benchmark in ' 'MIDICORE' WWER-1000 core periphery power tilt benchmark proposal'. (Author)

Seismic margin assessment and earthquake experience based methods for WWER-440/213 type NPPs

International Nuclear Information System (INIS)

Masopust, R.

1996-01-01

This report covers the review of the already completed studies, namely, safe shutdown system identification and classification for Bohunice NPP and the comparative study of standards and criteria. It contains a report on currently ongoing studies concerning seismic margin assessment and earthquake experience based methods in application for seismic evaluation and verification of structures and equipment components of the operating WWER-440/213 type NPPs. This is based on experiences obtained from Paks NPP. The work plan for the remaining period of Benchmark CRP and the new proposals are included. These are concerned with seismic evaluation of selected safety related mechanical equipment and pipes of Paks NPP, and the actual seismic issues of the Temelin WWER-1000 type NPP

Experimental investigation of power peak in vicinity of WWER-440 control rod at end of fuel cycle

International Nuclear Information System (INIS)

Mikus, J.

2004-01-01

This paper presents some results of the axial power (fission density) distribution measurements carried out on the light-water, zero-power reactor LR-0 in a WWER-440 type core in vicinity of the WWER-440 control rod model at zero boron concentration in moderator, modelling the conditions at the end of the WWER-440 fuel cycle. Further information concerns the control rod model description, specification of the LR-0 core, fuel assemblies and measurement conditions. The aim of performed experiment is enlargement of the available power peaking database to enable the validation of the calculation codes by means of the measured data that correspond to the end of WWER-440 fuel cycle. (author)

The international WWER fuel market

International Nuclear Information System (INIS)

Gingold, G.E.; Goldstein, L.; Strasser, A.A.

1994-01-01

The state of the world nuclear fuel market and its economic complexities are described. Currently the nuclear fuel market is oversupplied and nuclear fuel fabrication in the West far exceeds the anticipated demands. Actually the current demand is not much more than half of the capacity available to supply it. The Eastern Europe (excluding the plants in the Russian Federation) with its 20 WWER-440 and 12 WWER-1000 reactors in operation and additional 4 WWER-440 and 8 WWER-1000 units under construction is considered as a potential long-term market for the Western fuel fabricators. The following significant benefits of competition in the WWER fuel market for the operators of these reactors are : 1) lower cost; 2) more favorable contract terms and improved vendor cooperation with the customer; 3) accelerated technological development. A brief description of the main WWER fuel suppliers TVEL, ABB Atom, BNFL, EVF and Westinghouse, as well as the status of some new companies as CEZ and SEP is given. The principal differences between Western and WWER fuels are outlined. The advanced features offered by the Western vendors and Russian fuel supply organisations are discussed. 2 tabs., 1 fig

The international WWER fuel market

Energy Technology Data Exchange (ETDEWEB)

Gingold, G E; Goldstein, L; Strasser, A A [Stoller (S.M.) Corp., Pleasantville, NY (United States)

1994-12-31

The state of the world nuclear fuel market and its economic complexities are described. Currently the nuclear fuel market is oversupplied and nuclear fuel fabrication in the West far exceeds the anticipated demands. Actually the current demand is not much more than half of the capacity available to supply it. The Eastern Europe (excluding the plants in the Russian Federation) with its 20 WWER-440 and 12 WWER-1000 reactors in operation and additional 4 WWER-440 and 8 WWER-1000 units under construction is considered as a potential long-term market for the Western fuel fabricators. The following significant benefits of competition in the WWER fuel market for the operators of these reactors are : (1) lower cost; (2) more favorable contract terms and improved vendor cooperation with the customer; (3) accelerated technological development. A brief description of the main WWER fuel suppliers TVEL, ABB Atom, BNFL, EVF and Westinghouse, as well as the status of some new companies as CEZ and SEP is given. The principal differences between Western and WWER fuels are outlined. The advanced features offered by the Western vendors and Russian fuel supply organisations are discussed. 2 tabs., 1 fig.

Radiation embrittlement of WWER-1000 reactor vessel steels

International Nuclear Information System (INIS)

Nikolaeva, A.V.; Nikolaev, Yu.A.; Kevorkyan, Yu.R.

2001-01-01

Results obtained on the blank samples of materials of the WWER-1000 vessels irradiated by low density neutron flux are discussed. Chemical composition of the materials is characterized by the low content of the impurities (copper and phosphorus) and high content of nickel. Dependence of the radiation embrittlement of the WWER-1000 vessel materials on metallurgic variables and damage dose is treated. The research showed that nickel largely enhanced the radiation embrittlement. New dependences for determination of the radiation embrittlement real rate of the WWER-1000 vessel materials and its conservative estimation were developed [ru

ACT-1000. Group activation cross-section library for WWER-1000 type reactors

Energy Technology Data Exchange (ETDEWEB)

Zolotarev, K I; Pashchenko, A B [National Research Centre - A.I. Leipunsky Institute for Physics and Power Engineering, Obninsk (Russian Federation)

2001-10-01

The ACT-1000, a problem-oriented library of group-averaged activation cross-sections for WWER-1000 type reactors, is based on evaluated microscopic cross-section data files. The ACT-1000 data library was designed for calculating induced activity for the main dose-generated nuclides contained in WWER-1000 structural materials. In preparing the ACT-1000 library, 47 group-averaged cross-section data for the 10{sup -9}-17.33 MeV energy range were used to calculate the spatial-energy neutron flux distribution. (author)

WWER-440 fuel rod performance analysis with PIN-Micro and TRANSURANUS codes

International Nuclear Information System (INIS)

Vitkova, M.; Manolova, M.; Stefanova, S.; Simeonova, V.; Passage, G.; Lassmann, K.

1994-01-01

PIN-micro and TRANSURANUS codes were used to analyse the WWER-440 fuel rod behaviour at normal operation conditions. Two highest loaded fuel rods of the fuel assemblies irradiated in WWER-440 with different power histories were selected. A set of the most probable average values of all geometrical and technological parameters were used. A comparison between PIN-micro and TRANSURANUS codes was performed using identical input data. The results for inner gas pressure, gap size, local linear heat rate, fuel central temperature and fission gas release as a function of time calculated for the selected fuel rods are presented. The following conclusions were drawn: 1) The PIN-micro code predicts adequately the thermal and mechanical behaviour of the two fuel rods; 2) The comparison of the results obtained by PIN-micro and TRANSURANUS shows a reasonable agreement and the discrepancies could be explained by the lack of thoroughly WWER oriented verification of TRANSURANUS; 3) The advanced TRANSURANUS code could be successfully applied for WWER fuel rod thermal and mechanical analysis after incorporation of all necessary WWER specific material properties and models for the Zr+1%Nb cladding, for the fuel rod as a whole and after validation against WWER experimental and operational data. 1 tab., 10 figs., 10 refs

WWER-440 fuel rod performance analysis with PIN-Micro and TRANSURANUS codes

Energy Technology Data Exchange (ETDEWEB)

Vitkova, M; Manolova, M; Stefanova, S; Simeonova, V; Passage, G [Bylgarska Akademiya na Naukite, Sofia (Bulgaria). Inst. za Yadrena Izsledvaniya i Yadrena Energetika; Kharalampieva, Ts [Kombinat Atomna Energetika, Kozloduj (Bulgaria); Lassmann, K [European Atomic Energy Community, Karlsruhe (Germany). European Inst. for Transuranium Elements

1994-12-31

PIN-micro and TRANSURANUS codes were used to analyse the WWER-440 fuel rod behaviour at normal operation conditions. Two highest loaded fuel rods of the fuel assemblies irradiated in WWER-440 with different power histories were selected. A set of the most probable average values of all geometrical and technological parameters were used. A comparison between PIN-micro and TRANSURANUS codes was performed using identical input data. The results for inner gas pressure, gap size, local linear heat rate, fuel central temperature and fission gas release as a function of time calculated for the selected fuel rods are presented. The following conclusions were drawn: (1) The PIN-micro code predicts adequately the thermal and mechanical behaviour of the two fuel rods; (2) The comparison of the results obtained by PIN-micro and TRANSURANUS shows a reasonable agreement and the discrepancies could be explained by the lack of thoroughly WWER oriented verification of TRANSURANUS; (3) The advanced TRANSURANUS code could be successfully applied for WWER fuel rod thermal and mechanical analysis after incorporation of all necessary WWER specific material properties and models for the Zr+1%Nb cladding, for the fuel rod as a whole and after validation against WWER experimental and operational data. 1 tab., 10 figs., 10 refs.

Evaluation of efficiency of axial profiling in WWER-440 fuel assemblies

International Nuclear Information System (INIS)

Ananjev, Yu. A.; Kurakin, K. Yu.; Artemov, V.G.; Ivanov, A.S.

2005-01-01

The present report deals with consideration of fuel enrichment axial profiling in WWER-440 assemblies. The study is performed on improving the effectiveness of fuel utilization using the example of implementing the axial profiling in the assemblies of the second generation. For simulation of fuel loadings the computer code package SAPFIR 9 5 and RC is used that allows for correct consideration of specific features of assemblies design changes. The methodical approach to assessment of effectiveness of implementing the axial profiling is considered with the use of capabilities of the mentioned code package. In conclusion the recommendations are given on using the fuel enrichment axial profiling in WWER-440 assemblies (Authors)

Development of anti-debris filter for WWER-440 working fuel assembly

International Nuclear Information System (INIS)

Kolosovsky, V.; Aksyonov, P.; Kukushkin, Y.; Molchanov, V.; Kolobaev, A.

2006-01-01

Mechanical damaging of the fuel rod claddings caused by debris is one of the main reasons for fuel assembly failures. The paper focuses on the program and results of experimental and design activities carried out by Russian organizations relating to the development and investigation of operational characteristics of anti-debris filters for WWER-440 working fuel assemblies. Lead working fuel assemblies equipped with anti-debris filters have been loaded in the core of Kola-2 NPP. The results obtained can be used for making the decision concerning the application of anti-debris filter for WWER-440 working fuel assemblies with the purpose of enhancing their debris-resistance properties. (authors)

Ranking of safety issues for WWER-440 model 230 nuclear power plants

International Nuclear Information System (INIS)

1992-02-01

In response to requests from Member States operating Soviet designed WWER-440/230 nuclear power plants (NPPs) for assistance through the IAEA's nuclear safety services, a major international project was established to evaluate these first generation reactors as a complement to relevant ongoing national, bilateral and multilateral activities. The objective is to assist countries operating WWER-440/230 NPPs in performing comprehensive safety reviews aimed at identifying design and operational weaknesses. The scope of the project includes a review of the conceptual design of WWER-440/230 NPPs, safety review missions to each one of the operating reactors to review design and operational aspects and studies to resolve issues of generic safety concern. This report was prepared by a group of international experts and the IAEA staff and discussed by the Project Steering Committee, December 9-13, 1991 in Vienna. An overview of the safety issues identified is presented indicating their effect on the performance of the basic safety functions. Conceptual recommendations related to design issues are given as a technical basis for the safety modifications required

Perspective decisions of WWER nuclear fuel: Implementation at Russian NPPs

International Nuclear Information System (INIS)

Molchanov, V.

2003-01-01

The scientific and technical policy pursued by JSC TVEL has managed to create a new generation of fuel assembly design on the basis of solutions tested at various units of Russian NPPs - Kola NPP, Kalinin NPP, Unit 1, Balakovo NPP Unit 1. The requirements set for the new generation nuclear fuel for WWER are: 1) High fuel burnup - up to 70 MWxdays/kgU; 2) Extended operation cycle - up to 6 years; 3) Increase of uranium charge to the core; 4) Increased lateral stability - bow not more than 7 mm; 5) High level of operating reliability - fuel rod leakage not worse than 10-5 1/year; 6) Demountable fuel assembly design. Post-irradiation examination results of fuel assemblies discharged from WWER-1000 reactors demonstrate that fuel rods have substantial reserve in general characteristics including that of dealing with planned burnup. In order to meet the requirements, trials are started for: implementation of rigid skeleton (WWER-1000); fuel column length extension (WWER-1000 and WWER-440); increase of UO 2 charge (WWER-1000 and WWER-440); enhancing of operational reliability and demountable design. It is concluded that the Russian nuclear fuel for WWER-type reactors is competitive and enables the implementation of state-of-the-art cost effective fuel cycles

Power peak in vicinity of WWER-440 control rod

International Nuclear Information System (INIS)

Mikus, J.

2003-01-01

The measurements of axial power (fission density) distribution have been performed by means of gamma activity determination (gamma scanning method) of the irradiated fuel pins detecting gamma quanta in the La peak area - 1596.5 keV of their selected parts having 20 mm length in the axial coordinates range 50-950 mm with a 10 mm step using a rectangular collimator (dimensions 20x10 mm). Two NaI(Tl) scintillation crystals (one as a monitor) with diameter of 40 mm were used, each of them in Pb shielding (thickness 150 mm). The obtained results enlarge the available 'power peaking database' and enable validation of the codes also in important case of zero-boron concentration that corresponds to the end of WWER-440 fuel cycle. This validation can improve the reliability of the calculation results of the power distribution in WWER-440 cores, re-loading schemes etc

WWER-440 type reactor core

International Nuclear Information System (INIS)

Mizov, J.; Svec, P.; Rajci, T.

1987-01-01

Assemblies with patly spent fuel of enrichment within 5 and 36 MWd/kg U or lower than the maximum enrichment of freshly charged fuel are placed in at least one of the peripheral positions of each hexagonal sector of the WWER-440 reactor type core. This increases fuel availability and reduces the integral neutron dose to the reactor vessel. The duration is extended of the reactor campaign and/or the mean fuel enrichment necessary for the required duration of the period between refuellings is reduced. Thus, fuel costs are reduced by 1 up to 3%. The results obtained in the experiment are tabulated. (J.B.). 1 fig., 3 tabs

Calculational modeling of fuel assemblies of WWER-1000 type with the use of burnable absorber Gadolinum; comparative analysis

International Nuclear Information System (INIS)

Yeremenko, M.L.; Kovbasenko, Yu.P.; Loetsch, T.

2001-01-01

In connection with the beginning of the use of fuel assemblies with burnable absorbers by integration of Gadolinum into the nuclear fuel at Ukrainian NPP the task of testing the code systems and the pertinent neutron cross section libraries for the new fuel arose. Taking into account the long term experience of German experts with calculations and evaluation of nuclear fuel containing Gadolinum it was decided to carry out a series of test calculations for fuel assembly lattices of PWR, WWER-440 and WWER-1000 types using the NESSEL/PYTHIA and CASMO/SIMULATE code systems (Authors)

WWER safety investigations on LR-0 reactor

International Nuclear Information System (INIS)

Mikus, J.

2001-01-01

A set of the measurement needed for the WWER-440 and WWER-1000 reactor lifetime assessment, verification of the methods, codes and input cross section libraries for the WWER reactor pressure vessel exposure evaluation has been performed on the LR-0 experimental reactor. The WWER Mock-ups (engineering benchmarks) has been carried out on the reactor, with the aim to investigate differential neutron spectra for reactor dosimetry purposes. Critical experiments have also been performed to determine the perturbation of the fission density distribution caused by the WWER-440 control assembly. Such assembly, partially inserted in the core, has significant influence on the space power distribution. A wide research program for sub-criticality investigations of the spent nuclear fuel storage has been realized on the LR-0 reactor. A benchmark experiment is realized on the reactor in corresponding geometry for CASTOR 440/84 container for storage and transportation of spent fuel. Critical experiments with new fuel assemblies including various burnable absorbers and different enrichments are performed. A set of critical experiments is performed using the fuel assemblies with 3,6% and 4,4% enrichment, arranged in the WWER-440 type cores with various lattice pitch. The critical high of the moderator level and the moderator level coefficient of reactivity are measured and the effect of the fuel assembly, placed in a hexagonal tube of stainless steel containing boron absorber (ATABOR - STANDARD) is investigated. The obtained results are used for the validation of the codes (MCNP, KENO and SCALE) in the frame of the contract 'Burn-up credit implementation for the storage and transport containers of the spent fuel'. Combined neutron-gamma spectra measurements in the WWER-1000 Mock-up are carried out during 2001

Benchmarking of multigroup neutron cross sections libraries on neutron transmission through WWER-440 vessel

International Nuclear Information System (INIS)

Ilieva, K.; Belousov, S.; Apostolov, T.

1998-01-01

The verification of calculated neutron fluence onto the WWER-440/230 pressure vessel is very topical task in particular referring that some of this type of reactors have been operated the major part of its design lifetime. Since the induced activity from the neutron irradiation onto the elements is a simple response of neutron flux the neutron fluence verification usually is done using the measured activity of radionuclides produced during reactor operation. Calculational and experimental results of 54 Mn induced activity of scraps from inner wall of Unit 1 reactor pressure vessel after 18th cycle and detectors irradiated behind the vessel during the 18th cycle of Unit 1 at Kozloduy NPP as well as neutron flux attenuation through the WWER-440/230 pressure vessel are presented. Neutron cross sections libraries generated on the base of ENDF/B-IV and ENDF/B-VI have been used in the calculations. The comparative analysis of evaluated activities and attenuation coefficient demonstrates the better reliability of the neutron fluence calculations by the libraries based on ENDF/B-VI than by ones on ENDF/B-IV. The extreme rarity of data for the activity of scraps from the WWER-440 reactor vessel and its combination with the data for the detectors irradiated behind the vessel makes them especially attractive for verification of calculational methods of neutron fluence onto the WWER-440 vessel with dummy cassettes loading. (author)

Contribution to the WWER-440 Gd-assembly evolution

International Nuclear Information System (INIS)

Cudrnak, P.; Darilek, P.; Necas, V.

2009-01-01

Development activities, presented in the paper, contribute to the evolution of gadolinium fuel for the WWER-440 reactors. Short overview of existing and already proposed Gd-assemblies is given. Two new assembly types with improved features are described. Multiplication coefficients and pin power peaking factors of all mentioned gadolinium assemblies are compared. Animations of power distribution behaviour in selected Gd-assemblies are shown. (Authors)

Design of the WWER-440 pressurizer

International Nuclear Information System (INIS)

Bednarek, L.

1978-01-01

The main specifications are presented of a pressurizer for the WWER-440 reactor as are factors securing operating reliability and the required life of the equipment. Ferritic-pearlite steel 22K is the basic material for the manufacture of the shell, support and couplings. The internal parts and the heads are manufactured from the 08KH18N10T chromium-nickel austenitic steel, the bolts and nuts of manholes from chromium-molybdenum steels 25KH1MF and 25KH2MFA. Quality testing of basic materials and quality control during the process of manufacture are briefly described. (Z.M.)

Temperature etalon of WWER-440 reactor

International Nuclear Information System (INIS)

Stanc, S.; Slanina, M.

2001-01-01

The presentation deals with the description, parameters and advantages of use of the temperature etalon. The system ensures temperature measurement of reactor outlet and inlet temperatures with high accuracy. Accuracy of temperature measurement is 0.18 deg C, accuracy of temperature difference measurement is 0.14 deg C, both with probability 0.95. Using the temperature etalon it is possible to increase accuracy of the standard temperature reactor measurements and to check their accuracy in the course of power reactor statuses in every measurement cycle. Temperature reactor etalon was installed in 12 WWER-440 units in Slovakia, Bohemia and Bulgaria. (Authors)

Analysis of operating reliability of WWER-1000 unit

International Nuclear Information System (INIS)

Bortlik, J.

1985-01-01

The nuclear power unit was divided into 33 technological units. Input data for reliability analysis were surveys of operating results obtained from the IAEA information system and certain indexes of the reliability of technological equipment determined using the Bayes formula. The missing reliability data for technological equipment were used from the basic variant. The fault tree of the WWER-1000 unit was determined for the peak event defined as the impossibility of reaching 100%, 75% and 50% of rated power. The period was observed of the nuclear power plant operation with reduced output owing to defect and the respective time needed for a repair of the equipment. The calculation of the availability of the WWER-1000 unit was made for different variant situations. Certain indexes of the operating reliability of the WWER-1000 unit which are the result of a detailed reliability analysis are tabulated for selected variants. (E.S.)

Nuclear safety improvement activities related to WWER-440 units in Bulgaria

International Nuclear Information System (INIS)

Gantchev, T.

1998-01-01

The systematic evaluation of the deficiencies of the original design of the WWER reactors brought to the development of a Short Term Programme for Safety Upgrading and Modernisation of Kozloduy WWER-440 units. The implementation of this Programme was completed in 1997. The strive for continuos improvement of Kozloduy Nuclear Power Plant (NPP) safety level, the new requirements of the Bulgarian Nuclear Safety Authority and the public concern initiated the development of new Complex Programme for Safety Improvement (PRG'97), now in a process of implementation. (author)

Strength analyses of the bubbler condenser structure of WWER-440 model 213 nuclear power plants. Reference plant: Bohunice V2 (Slovakia). Report of the IAEA Technical Co-operation Project RER/9/004 on evaluation of safety aspects of WWER-440 model 213 nuclear power plants

International Nuclear Information System (INIS)

1995-06-01

This publication addresses the topic of mechanical strength of the bubbler condenser applied in the WWER-440 model 213 plants and is intended to assist WWER-440/213 operators in the re-assessment of the bubbler condenser performance. It is hoped that it will also be useful to anyone working in the field of WWER safety, and in particular to experts planning, executing or reviewing studies related to the subject. Refs, figs and tabs

Strength analyses of the bubbler condenser structure of WWER-440 model 213 nuclear power plants. Reference plant: Bohunice V2 (Slovakia). Report of the IAEA Technical Co-operation Project RER/9/004 on evaluation of safety aspects of WWER-440 model 213 nuclear power plants

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-06-01

This publication addresses the topic of mechanical strength of the bubbler condenser applied in the WWER-440 model 213 plants and is intended to assist WWER-440/213 operators in the re-assessment of the bubbler condenser performance. It is hoped that it will also be useful to anyone working in the field of WWER safety, and in particular to experts planning, executing or reviewing studies related to the subject. Refs, figs and tabs.

Report of a consultants meeting on accidents during shutdown conditions for WWER nuclear power plants. Extrabudgetary programme on the safety of WWER NPPs

International Nuclear Information System (INIS)

1996-07-01

The main objectives of the meeting were to exchange information on the operational occurrences, studies performed and countermeasures taken for the accidents during shutdown for WWERs, and to define the necessity and directions of the further activities which may promote the improvement of WWER safety under shutdown conditions. The consultants have discussed some aspects concerning vulnerability of safety functions during shutdown conditions, several steps required to performed accident analysis and selected operational aspects for shutdown conditions. The discussion was supported by an evaluation of selected operational occurrences. The consultants have agreed that the discussion during the meeting in major parts is relevant to all the WWER designs (i.e. WWER-1000, WWER-440/213 and WWER-440/230). As for the plant conditions, the consultants have agreed to bound the discussion mainly by the cold shutdown and refuelling modes. Refs, figs, tabs

Steam generator collector integrity of WWER-1000 reactors. IAEA extrabudgetary programme on the safety of WWER NPPs

Energy Technology Data Exchange (ETDEWEB)

Lin, C.; Strupczewski, A. [International Atomic Energy Agency, Vienna (Austria)

1995-12-31

At the Consultants` Meeting on `The Safety of WWER-1000 Model 320 Nuclear Power Plants` organized by the IAEA within the framework of its Extrabudgetary Programme on the Safety of WWER-1000 NPPs, which was held in Vienna, 1-5 June 1992, the problem of WWER-1000 steam generator integrity was identified as an important issue of safety concern. Considering the safety importance of this issue, a Consultants` Meeting on `The Steam Generator Integrity of WWER-1000 Nuclear Power Plants` was convened in Vienna in May 1993, attended by 15 international experts in the area to compile information on the steam generator operating experience, deficiencies and corrective measures implemented and planned. In order to also include information from the main designer OKB Gidropress and to finalize the meeting report the IAEA convened a second meeting on the issue on 23-27 November 1993. The present paper summarizes the information and conclusions from those meetings.

Steam generator collector integrity of WWER-1000 reactors. IAEA extrabudgetary programme on the safety of WWER NPPs

Energy Technology Data Exchange (ETDEWEB)

Lin, C; Strupczewski, A [International Atomic Energy Agency, Vienna (Austria)

1996-12-31

At the Consultants` Meeting on `The Safety of WWER-1000 Model 320 Nuclear Power Plants` organized by the IAEA within the framework of its Extrabudgetary Programme on the Safety of WWER-1000 NPPs, which was held in Vienna, 1-5 June 1992, the problem of WWER-1000 steam generator integrity was identified as an important issue of safety concern. Considering the safety importance of this issue, a Consultants` Meeting on `The Steam Generator Integrity of WWER-1000 Nuclear Power Plants` was convened in Vienna in May 1993, attended by 15 international experts in the area to compile information on the steam generator operating experience, deficiencies and corrective measures implemented and planned. In order to also include information from the main designer OKB Gidropress and to finalize the meeting report the IAEA convened a second meeting on the issue on 23-27 November 1993. The present paper summarizes the information and conclusions from those meetings.

Study on steam separation in steam generators of a NPP with the WWER-440 reactors

International Nuclear Information System (INIS)

Dmitriev, A.I.; Kolzov, Yu.V.; Titov, V.F.; Dubrovin, A.V.; Ilyushin, V.F.; Volkov, A.P.

1977-01-01

The separation characteristics as well as the actual level position in steam generators with and without a submerged holy sheet have been determined at a WWER-440 reactor nuclear power plant. It has been shown, that without changing the design of steam generators their load at the WWER-440 reactor nuclear power plant can be increased by about 10%. In this case the vapour humidity does not exceed the permissible value equal to 0.25%. The submerged holy sheet considerably decreases load irregularity and swelling of the water-steam mixture layer

Fuel improvement and WWER-1000 FA main operational results

International Nuclear Information System (INIS)

Rozhkov, V.; Enin, A.; Bezborodov, Y.; Petrov, V.

2003-01-01

The JSC NCCP experience of WWER-1000 Fuel Assemblies (FAs) fabrication and operation confirms the adequate feasibility and efficiency of fuel operation in 3-4-x fuel cycles, high operating reliability and competitive capacity as compared with foreign analogues. The work on fuel improvement is aimed at an improvement of the operating reliability and an enhancement of the fuel use efficiency in WWER-1000 advanced FAs

Selected safety aspects of containments for nuclear power plants with WWER-440 reactors

International Nuclear Information System (INIS)

Jankowski, M.W.; Kulig, M.J.; Strupczewski, A.; Balabanov, E.D.

1996-01-01

Considerable attention has been and continues to be focused on the design and operational features that prevent the release of radioactive materials to the environment for a spectrum of accidents for the two classes of WWER-440 reactors: the older 230 model and the more recently designed 213 models. This paper, based on published and unpublished information, aims to clarify the perceptions of the Russian WWER-440 models 230 and 213 nuclear power plant containment system designs and their relevance to selected aspects of accident mitigation. It should be noted that these are unclearly and often negatively perceived, primarily because of a lack of reliable information and a poorly assembled experimental database. Conflicting statements have been made regarding the nature and the features of the plant's containment system. The paper presents a brief outline of the design of both WWER-440 models with respect to their confinement functions. Selected safety-related aspects of the accident localization systems are discussed, and the recognized shortcomings and safety merits are pointed out. The older 230 units experience high leak rates and are designed to withstand medium-size pipe breaks. The possible implications for safety are pointed out in the paper. The on going studies that concentrate on improving the system are highlighted. (orig.)

Twenty years of operation of WWER 440/230 units in Jaslovske Bohunice

International Nuclear Information System (INIS)

Tomek, J.

1998-01-01

It is twenty years this year since the first unit WWER 440 of Slovak Nuclear Power Plant Jaslovske Bohunice was commissioned. There are four units WWER 440 in operation Jaslovske Bohunice site. First two units of older soviet PWR design V-230 (also known as V-1) and other two units of newer V-213 type (also known as V-2). The goal of this presentation is to summarize and evaluate the operation of Unit 1 and 2 for this period of time and mainly to describe what has been done and what is planned to be done to increase the nuclear safety and operational reliability of both units. The operating organization and regulatory authority assume that an internationally acceptable level of safety will be reached by accomplishing of the upgrading program.(author)

Performance of the Westinghouse WWER-1000 fuel design

International Nuclear Information System (INIS)

Hoglund, J.; Riznychenko, O.; Latorre, R.; Lashevych, P.

2011-01-01

In 2005 six (6) Westinghouse WWER-1000 Lead Test Assemblies (LTAs) were loaded in the South Ukraine Unit 3. This design has demonstrated full compatibility with resident fuel designs and all associated fuel handling and reactor components. Operations have further demonstrated adequacy of performance margins and the reliability requirements for multiple cycles of operation. The LTA's have now been discharged after completing the planned four cycles of operation and having reached an average assembly burnup in excess of 43 MWd/kgU. Post Irradiation Examinations were performed after completion of each cycle. The final LTA inspection program at end of Cycle 20 in 2010 yielded satisfactory results on all counts, and it was concluded that the 6 Westinghouse LTA's performed as expected during their operational regimes. Very good performance was demonstrated in the WWER-1000 reactor environment for the Zr-1%Nb as grid material, and ZIRLO fuel cladding and structural components. Control Rod Assemblies drop times and drag forces were all within the accepted values. The LTA program demonstrated that this fuel design is suitable for full core applications. However, the topic of fuel assembly distortion resistance was re-visited and Westinghouse therefore considered operational experience and design features from multiple development programs to enhance the basic Westinghouse WWER-1000 fuel design for Ukrainian reactors. The design now includes features that further mitigate assembly bow while at the same time improving the fuel cycle economy. This paper describes briefly the development of the Westinghouse WWER-1000 fuel design and how test results and operational experiences from multiple sources have been utilized to produce a most suitable fuel design. Early in 2011 a full region of the Westinghouse WWER-1000 design completed another full cycle of operation at South Ukraine Unit 3, all with excellent results. All 42 fuel assemblies were examined for visible damage or non

Modeling of WWER-440 Fuel Pin Behavior at Extended Burn-up

International Nuclear Information System (INIS)

El-Koliel, M.S.; Abou-Zaid, A.A.; El-Kafas, A.A.

2004-01-01

Currently, there is an ongoing effort to increase fuel discharge burn-up of all LWRs fuel including WWER's as much as possible in order to decrease power production cost. Therefore, burn-up is expected to be increased to 60 to 70 Mwd/kg U. The change in the fuel radial power distribution as a function of fuel burn up can affect the radial fuel temperature distribution as well as the fuel microstructure in the fuel pellet rim. In this paper, the radial burn-up and fissile products distributions of WWER-440 UO 2 fuel pin were evaluated using MCNP 4B and ORIGEN2 codes. The impact of the thermal conductivity on predicted fission gas release calculations is needed. For the analysis, a typical WWER-440 fuel pin and surrounding water moderator are considered in a hexagonal pin cell well. The thermal release and the athermal release from the pellet rim were modeled separately. The fraction of the rim structure and the excessive porosity in the rim structure in isothermal irradiation as a function of the fuel burn-up was predicted. a computer program; RIMSC-01, is developed to perform the required FGR calculations. Finally, the relevant phenomena and the corresponding models together with their validation are presented

WWER 440 integrity assessment with respect to PTS events

International Nuclear Information System (INIS)

Hrazsky, M.; Mikua, M.; Hermansky, P.

1997-01-01

The present state of art in WWER 440 RPV integrity assessment with respect to PTS events utilized in Slovakia is reviewed briefly in this paper. Recent results of some PTS's (very severe) analyses, shortly described in our paper, have confirmed the necessity of elaboration of new more sophisticated procedures again. Such methodology should be based on prepared IAEA Guidance. (author). 13 refs, 1 fig

WWER 440 integrity assessment with respect to PTS events

Energy Technology Data Exchange (ETDEWEB)

Hrazsky, M; Mikua, M; Hermansky, P [Nuclear Power Plant Research Inst. Trnava Inc., Trnava (Slovakia)

1997-09-01

The present state of art in WWER 440 RPV integrity assessment with respect to PTS events utilized in Slovakia is reviewed briefly in this paper. Recent results of some PTS`s (very severe) analyses, shortly described in our paper, have confirmed the necessity of elaboration of new more sophisticated procedures again. Such methodology should be based on prepared IAEA Guidance. (author). 13 refs, 1 fig.

Development of a new WWER-440 fuel design

International Nuclear Information System (INIS)

Coucil, D.; Totev, T.

1998-01-01

In March 1996 British Nuclear Fuel Limited signed a contract with Imatran Voima and Paks Nuclear Power Plant to design, develop, license and supply 5 Lead Test Assemblies to the WWER-440 reactor at Loviisa in Finland. In June 1998 the manufacture of these 5 assemblies (4 fixed assemblies and 1 follower assembly) was completed. The fuel is expected to be loaded into Loviisa Unit 2 reactor during the shutdown scheduled for September of this year. (Authors)

Use of Main Loop Isolating Valves (GZZS) in WWER 440

International Nuclear Information System (INIS)

Stefanova, A.E.; Gencheva, R.V.; Groudev, P.P.

2002-01-01

This paper discusses the usage of Main Loop Isolation Valves in case of Steam Generator Tube Rupture accident in WWER440/V230. A double-ended single pipe break in SG-6 was chosen as representative. In the paper are investigated two cases. In the first one the operator isolates the affected loop by Main Loop Isolation Valves closing and after primary depressurization re-opens them to cooldown the damaged Steam Generator. The second case treats the situation, where Main Loop Isolation Valves fail to close with the necessary operator actions for managing plant recovery. RELAP5/MOD3.2 computer code has been used to simulate the Steam Generator Tube Rupture accident in WWER440 NPP model. This model was developed and validated at Institute for Nuclear Research and Nuclear Energy - Bulgarian Academy of Sciences. The results of analyses presented in this report demonstrate that in the both cases (with or without Main Loop Isolation Valves usage) the operator could bring the plant to stable and safety conditions (Authors)

Current state of WWER SNF storage in Russia and the perspectives

International Nuclear Information System (INIS)

Anisimov, O.; Kozlov, Y.; Razmashkin, N.; Safutin, V.; Tikhonov, N.

2006-01-01

In the Russian Federation WWER-440 Spent Nuclear Fuel (SNF) is reprocessed at RT-1 plant near Cheliabinsk. WWER-1000 SNF is supposed to be reprocessed at RT-2 plant, which will be built about 2020. The information on the capacity and fill up level of the at-reactor pools at NPP with WWER reactors considering its modification up to May 2005 is given. The regulatory requirements to all SNF 'wet' storage facilities; the principle design and engineering solutions as well as the complex of measures for radiation safety and the environmental protection of spent fuel storage are presented. WWER-440 SNF management, WWER-1000 SNF management and dry storage of WWER-1000 SNF are discussed. In the conclusion it is noted than neither Russia, nor any other country have the experience of construction of vault-type 'dry' storage facilities of such a capacity to store WWER-1000 SNF (9000 tU). The experience and design solutions approved earlier in creation of other dangerous facilities were used. The calculations were based on conservative assumptions allowing with a large assurance to guarantee the nuclear and radiation safety and the environmental protection. At present, a program is developed for scientific-technical support of the dry storage facility design and operation, aimed at the studies whose results will allow to optimize the taken technical decisions, simplify SNF management technology and, possibly, to reduce the cost of the storage facility itself

Fuel pin failure root causes and power distribution gradients in WWER cores

International Nuclear Information System (INIS)

Mikus, J.

2008-01-01

The purpose of this work is to investigate the influence of some core heterogeneities and reactor construction materials on space power distribution in WWER type cores, especially from viewpoint of the values and gradient occurrence that could result in static loads with some consequences, e.g., fuel pin (FP) or fuel assembly (FA) bowing and possible contribution to the FP failure root causes. Presented information were obtained by means of experiments on research reactor LR-0 concerning the: 1) Power distribution estimation on pellet surface of the FPs neighbouring a FP containing gadolinium (Gd 2 O 3 ) burnable absorber integrated into fuel in WWER-440 and -1000 type cores; 2) Power distribution measurement in periphery FAs neighbouring the baffle in WWER-1000 type cores and 3) Power distribution in FAs neighbouring the control rod absorbing part in a WWER-440 type core. (author)

Concentration of WWER-1000 unit power on one site

International Nuclear Information System (INIS)

Rousek, J.; Kysel, J.; Sladek, V.

1987-01-01

The problem of a suitable number of nuclear power plant units built on one site is discussed. Using an example of three sites being prepared now in Czechoslovakia, two alternatives - one with two WWER-1000 units, the other with four WWER-1000 units on one site - are evaluated from the viewpoint of long-range nuclear power development program in Czechoslovakia, costs, transmission of electric power and heat supply. (author). 10 tabs., 13 refs

Seismic upgrading of WWER 440-230 structures, units 1/2, Kozloduy NPP

International Nuclear Information System (INIS)

Stafanov, D.; Kostov, M.; Boncheva, H.; Varbanov, G.

1995-01-01

The purpose of this paper is to present final results from a big amount of computational work in connection with the investigations of the possibilities for upgrading of WWER 440-230 structures, units 1/2, Kozloduy NPP. (author)

Modelling of WWER-1000 fuel: state and prospects

International Nuclear Information System (INIS)

Medvedev, A.; Bibilashvili, Yu.; Bogatyr, S.; Khvostov, G.

1994-01-01

The role of START-3 code in studying and computerized modelling of post-irradiation behaviour of standard fuel rods in real operation conditions of WWER-1000 reactors is described. The models used in the code are based on experimental study of material properties, processes and post irradiation research on standard and experimental fuel pins. The code capability is verified by comparison with data from experiments on WWER test rods performed in MR reactor, the Russia-Finland tests SOFIT and the international program FUMEX. The comparison performed and the results thus obtained demonstrate the satisfactory ability of START-3 code to simulate fuel rod behaviour in normal operation condition. The calculations confirm the experimentally observed evidence of an essential margin on serviceability of WWER-1000 fuel pin with three year operation cycle permitting an increase in design fuel burnup. 2 tabs., 18 figs

Modelling of WWER-1000 fuel: state and prospects

Energy Technology Data Exchange (ETDEWEB)

Medvedev, A; Bibilashvili, Yu; Bogatyr, S; Khvostov, G [Vsesoyuznyj Nauchno-Issledovatel` skij Inst. Neorganicheskikh Materialov, Moscow (Russian Federation)

1994-12-31

The role of START-3 code in studying and computerized modelling of post-irradiation behaviour of standard fuel rods in real operation conditions of WWER-1000 reactors is described. The models used in the code are based on experimental study of material properties, processes and post irradiation research on standard and experimental fuel pins. The code capability is verified by comparison with data from experiments on WWER test rods performed in MR reactor, the Russia-Finland tests SOFIT and the international program FUMEX. The comparison performed and the results thus obtained demonstrate the satisfactory ability of START-3 code to simulate fuel rod behaviour in normal operation condition. The calculations confirm the experimentally observed evidence of an essential margin on serviceability of WWER-1000 fuel pin with three year operation cycle permitting an increase in design fuel burnup. 2 tabs., 18 figs.

Advanced fuel cycles for WWER-1000 reactors

International Nuclear Information System (INIS)

Semchenkov, Y. M.; Pavlovichev, A. M.; Pavlov, V. I.; Spirkin, E. I.; Styrin, Y. A.; Kosourov, E. K.

2007-01-01

Main stages of Russian uranium fuel development regarding improvement of safety and economics of fuel load operation are presented. Intervals of possible changes in fuel cycle duration have been demonstrated for the use of current and perspective fuel. Examples of equilibrium fuel load patterns have been demonstrated and main core neutronics parameters have been presented. Problems on the use of axial blankets with reduced enrichment in WWER-1000 fuel assemblies are considered. Some results are presented regarding core neutronic characteristics of WWER-1000 at the use of regenerated uranium and uranium-plutonium fuel. Examples of equilibrium fuel cycles for the core partially loaded with MOX fuel from weapon-grade plutonium are also considered (Authors)

Change in geometrical parameters of WWER high burnup fuel rods under operational conditions and transient testing

International Nuclear Information System (INIS)

Kanashov, B.; Amosov, S.; Lyadov, G.; Markov, D.; Ovchinnikov, V; Polenok, V.; Smirnov, A.; Sukhikh, A.; Bek, E.; Yenin, A.; Novikov, V.

2001-01-01

The paper discusses changes in fuel rods geometric parameters as result of operation conditions and burnups. The degree of geometry variability of fuel rods, cladding and column is one of the most important characteristics affecting fuel serviceability. On the other hand, changes in fuel rod geometric parameters influence fuel temperature, fission gas release, fuel-to-cladding stress strained state as well as the degree of interaction with FA skeleton elements and skeleton rigidity. Change in fuel-to-cladding gap is measured using compression technique. The axial distribution of fuel-to-cladding gap demonstrates the largest decrease of the gap in the region 500 to 2000 mm from the bottom of the fuel rod (WWER-440) and in the region of 500 to 3000 mm for WWER-1000. The cladding material creep in WWER fuel rods together with the radiation growth results in fuel rod cladding elongation. A set of transient tests for spent WWER-440 and WWER-1000 fuel rods carried out in SSC RIAR during a period 1995-1999, with the aim to estimate the changes in geometric parameters of FRs. The estimation of changes in outer diameter of cladding and fuel column and fuel-to-cladding gap are performed in transient conditions (changes in linear power range of 180 to 400 W/cm) for both WWER-440 and WWER-1000. WWER-440 fuel rods having the same burnup and close fuel-cladding contact before testing are subjected to considerable hoop cladding strain in testing up to 300 W/cm. But the hoop strain does not grow due to the structural changes in fuel column and decrease in central hole diameter occurred when the power is higher

Structural and leakage integrity assessment of WWER steam generator tubes

International Nuclear Information System (INIS)

Splichal, K.; Otruba, J.; Keilova, E.; Krhounek, V.; Turek, J.

1996-01-01

The leakage and plugging limits were derived for WWER steam generators based on leak and burst tests using tubes with axial part-through and through-wall defects. The following conclusions were arrived at: (i) The permissible primary-to-secondary leak rate with respect to the permissible through-wall defect size of WWER-440 and WWER-1000 steam generator tubes is 8 l/h. (ii) The primary-to-secondary leak rate is reduced by the blocking of the tube cracks by corrosion product particles and other substances. (iii) The rate of crack penetration through the tube wall is higher than the crack widening. (iv) The validity of the criterion of instability for tubes with through-wall cracks was confirmed experimentally. For the WWER-440 and WWER-1000 steam generators, the critical size of axial through-wall cracks, for the threshold primary-to-secondary pressure difference, is 13.8 and 12.0 mm, respectively. (v) The calculated leakage for the rupture of one tube and for the assumed extreme defects is two orders and one order of magnitude, respectively, higher than the proposed primary water leakage limit of 8 l/h. (vi) The experiments gave evidence that the use of the permissible thinning limit of 80% for the heat exchange tube plugging does not bring about uncontrollable leakage or unstable crack growth. This is consistent with experience gained at WWER-440 type nuclear power plants. 4 tabs., 5 figs., 9 refs

Databases on safety issues for WWER and RBMK reactors. Users' manual. A publication of the extrabudgetary programme on the safety of WWER and RBMK nuclear power plants

International Nuclear Information System (INIS)

1996-04-01

At the beginning of the IAEA Extrabudgetary Programme on the safety of WWER reactors a great number of findings and recommendations (safety items) were collected as a result of design review and safety review missions of the WWER-440/230 type reactors. On the basis of these findings a technical database containing more than 1300 records was established to support the consolidation of the information obtained and to help in identification of safety issues. After the scope of the WWER extrabudgetary programme was extended similar data sets were prepared for the WWER-440/213, WWER-1000 and RBMK nuclear power plants. This publication describes the structure of the databases on safety issues of WWER and RBMK NPPs, the information sources used in the databases and interrogation capabilities for users to obtain the necessary information. 14 refs, 9 figs, 5 tabs

Solution and implementation of project ''Simulator of WWER-440 nuclear power plant''

International Nuclear Information System (INIS)

Koukal, V.

1985-01-01

The time data are given of the development and construction of the simulator of a WWER-440 nuclear power plant unit. The individual tasks are summed up which are related to the project implementation, and cooperating institutions and enterprises are listed. (J.C.)

Surveillance extension experience at WWER-440 type reactors

International Nuclear Information System (INIS)

Gillemot, F.; Uri, G.; Oszwald, F.; Trampus, P.

1993-01-01

In WWER-440 reactors, the surveillance specimens are located in accelerated irradiation positions. After 5 years, all specimens are withdrawn and the operational changes are not monitored. At Paks NPP a new surveillance program extension has been settled in order to avoid these original program disadvantages and generate further data for plant lifetime management. This paper includes: research performed to prepare the surveillance extension programme, the evaluation method for the surveillance extension, and first results (Charpy and tensile tests). (authors). 6 refs., 12 figs., 3 tabs

Surveillance extension experience at WWER-440 type reactors

Energy Technology Data Exchange (ETDEWEB)

Gillemot, F; Uri, G [Budapesti Mueszaki Egyetem, Budapest (Hungary); Oszwald, F; Trampus, P

1994-12-31

In WWER-440 reactors, the surveillance specimens are located in accelerated irradiation positions. After 5 years, all specimens are withdrawn and the operational changes are not monitored. At Paks NPP a new surveillance program extension has been settled in order to avoid these original program disadvantages and generate further data for plant lifetime management. This paper includes: research performed to prepare the surveillance extension programme, the evaluation method for the surveillance extension, and first results (Charpy and tensile tests). (authors). 6 refs., 12 figs., 3 tabs.

Results of neutron physics analyses of WWER-440 cores with modified reactor protection and control systems

International Nuclear Information System (INIS)

Lehmann, M.; Pecka, M.; Rocek, J.; Zalesky, K.

1993-12-01

Detailed results are given of neutron physics analyses performed to assess the efficiency and acceptability of modifications of the WWER-440 core protection and control system; the modifications have been proposed with a view to increasing the proportion of mechanical control in the compensation of reactivity effects during reactor unit operation in the variable load mode. The calculations were carried out using the modular MOBY-DICK macrocode system together with the SMV42G36 library of two-group parametrized diffusion constants, containing corrections which allow new-design WWER-440 fuel assemblies to be discriminated. (J.B). 37 tabs., 18 figs., 5 refs

Advanced fuel cycles and burnup increase of WWER-440 fuel

International Nuclear Information System (INIS)

Proselkov, V.; Saprykin, V.; Scheglov, A.

2003-01-01

Analyses of operational experience of 4.4% enriched fuel in the 5-year fuel cycle at Kola NPP Unit 3 and fuel assemblies with Uranium-Gadolinium fuel at Kola NPP Unit 4 are made. The operability of WWER-440 fuel under high burnup is studied. The obtained results indicate that the fuel rods of WWER-440 assemblies intended for operation within six years of the reviewed fuel cycle totally preserve their operability. Performed analyses have demonstrated the possibility of the fuel rod operability during the fuel cycle. 12 assemblies were loaded into the reactor unit of Kola 3 in 2001. The predicted burnup in six assemblies was 59.2 MWd/kgU. Calculated values of the burnup after operation for working fuel assemblies were ∼57 MWd/kgU, for fuel rods - up to ∼61 MWd/kgU. Data on the coolant activity, specific activity of the benchmark iodine radionuclides of the reactor primary circuit, control of the integrity of fuel rods of the assemblies that were operated for six years indicate that not a single assembly has reached the criterion for the early discharge

Contemporary and prospective fuel cycles for WWER-440 based on new assemblies with higher uranium capacity and higher average fuel enrichment

International Nuclear Information System (INIS)

Gagarinskiy, A.A.; Saprykin, V.V.

2009-01-01

RRC 'Kurchatov Institute' has performed an extensive cycle of calculations intended to validate the opportunities of improving different fuel cycles for WWER-440 reactors. Works were performed to upgrade and improve WWER-440 fuel cycles on the basis of second-generation fuel assemblies allowing core thermal power to be uprated to 107 108 % of its nominal value (1375 MW), while maintaining the same fuel operation lifetime. Currently intensive work is underway to develop fuel cycles based on second-generation assemblies with higher fuel capacity and average fuel enrichment per assembly increased up to 4.87 % of U-235. Fuel capacity of second-generation assemblies was increased by means of eliminated central apertures of fuel pellets, and pellet diameter extended due to reduced fuel cladding thickness. This paper intends to summarize the results of works performed in the field of WWER-440 fuel cycle modernization, and to present yet unemployed opportunities and prospects of further improvement of WWER-440 neutronic and operating parameters by means of additional optimization of fuel assembly designs and fuel element arrangements applied. (Authors)

WWER-1000 fuel cycles: current situation and outlook

International Nuclear Information System (INIS)

Kosourov, E.; Pavlov, V.; Pavlovichev, A.; Spirkin, E.; Shcherenko, A.

2013-01-01

Usage mode of nuclear fuel in WWER type reactor has been changed significantly till the moment of the first WWER-1000 commissioning. There are a lot of improvements, having an impact on the fuel cycle, have been implemented for units with WWER-1000. FA design and its constructional materials, FA fuel weight, burnable poison, usage mode of units and etc have been modified. As the result of development it has been designed a modern FA with rigid skeleton. As a whole it allows to use more efficient configurations of the core, to extend range of fuel cycle lengths and to provide good flexibility in the operation. In recent years there were in progress works on increasing FA uranium capacity. As the result there were developed two designs of the fuel rod: 1) the fuel column height of 3680 mm, diameters of the fuel pellet and its central hole of 7.6 and 1.2 mm respectively and 2) the fuel column height of 3530 mm, the fuel pellet diameter of 7.8 mm without the central hole. Such fuel rods have operating experience as a part of different FA designs. Positive operating experience was a base of new FA (TVS-4) development with the fuel column height of 3680 mm and the fuel pellet diameter of 7.8 mm without the central hole. The paper presents the overview of WWER-1000, AES-2006 and WWER-TOI fuel cycles based on FAs with fuel rod designs described above. There are demonstrated fuel cycle possibilities and its technical and economic characteristics. There are discussed problems of further fuel cycle improvements (fuel enrichment increase above 5 %, use of erbium as alternative burnable poison) and their impact on neutronics characteristics. (authors)

Radiation stability and recovery of WWER-440 materials

Energy Technology Data Exchange (ETDEWEB)

Amaev, A; Kryukov, A; Levit, V; Platonov, P; Sokolov, M

1994-12-31

The main results of a complex investigation of radiation embrittlement of WWER-440 reactor vessel materials, carried out in Russia, are presented. The effect of the annealing temperature and annealing time, neutron fluence, and phosphorous and copper impurity contents on the recovery of the ductile-to-brittle transition temperature are studied. It is shown that the recovery of the transition temperature depends mainly on the annealing temperature. At an annealing temperature of 420 and 460 C, residual post-annealing embrittlement does not depend on neutron fluence. 14 figs., 3 tabs.

Radiation stability and recovery of WWER-440 materials

International Nuclear Information System (INIS)

Amaev, A.; Kryukov, A.; Levit, V.; Platonov, P.; Sokolov, M.

1993-01-01

The main results of a complex investigation of radiation embrittlement of WWER-440 reactor vessel materials, carried out in Russia, are presented. The effect of the annealing temperature and annealing time, neutron fluence, and phosphorous and copper impurity contents on the recovery of the ductile-to-brittle transition temperature are studied. It is shown that the recovery of the transition temperature depends mainly on the annealing temperature. At an annealing temperature of 420 and 460 C, residual post-annealing embrittlement does not depend on neutron fluence. 14 figs., 3 tabs

Calculational results for radiation embrittlement of WWER pressure vessel at the Kozloduy NPP

Energy Technology Data Exchange (ETDEWEB)

Apostolov, T; Ilieva, K; Petrova, T [Bylgarska Akademiya na Naukite, Sofia (Bulgaria). Inst. za Yadrena Izsledvaniya i Yadrena Energetika

1996-12-31

Determination of radiation impact on metal state in the case of WWER-440/230 is made only by calculation methods since a special sample-witness (SW) incorporation had not been implemented. In WWER-1000 reactors such SW are foreseen but their spots are high above the active core. This is why in both reactors the appliance of a calculational procedure for radiation embrittlement determination is compulsory. The authors propose such a procedure accounting for the change in critical temperature of neutron brittleness by the neutron fluence. The neutron fluence and the shift of critical embrittlement temperature have been calculated for the maximum overloaded location and for the weld metal of the Kozloduy-5 and Kozloduy-6 reactors (WWER-1000). The shift of critical temperature in weld 4 of the Units 1-4 (WWER-440) is plotted versus work cycles and compared to experimental values. 4 figs., 5 tabs.

Innovation of genetic algorithm code GenA for WWER fuel loading optimization

International Nuclear Information System (INIS)

Sustek, J.

2005-01-01

One of the stochastic search techniques - genetic algorithms - was recently used for optimization of arrangement of fuel assemblies (FA) in core of reactors WWER-440 and WWER-1000. Basic algorithm was modified by incorporation of SPEA scheme. Both were enhanced and some results are presented (Authors)

Simulation of the dynamic behaviour of the secondary circuit of a WWER-440 type nuclear power plant Pt. 2

International Nuclear Information System (INIS)

Doorenbos, J.; Gacs, A.; Kiss, Zs.

1987-12-01

This report describes the dynamic simulation models of the most important controllers of the secondary circuit of a WWER-440 type nuclear power plant, i.e., the hydraulic turbine controller and the level controls of the condenser hotwell and that of the feedwater tank. Simulation results are also presented. (For dynamic simulation models of the primary circuit of WWER-440 type reactors see Reports KFKI--1983-127 and KFKI--1985-08.) (author) 15 figs

Experience of developments and implementation of advanced fuel cycles of WWER-440 reactors

International Nuclear Information System (INIS)

Gagarinski, A.A.; Lizorkin, M.P.; Novikov, A.N.; Proselkov, V.N.; Saprykin, V.V.

2000-01-01

The paper presents the experience of development and implementation of advanced four- and five-year fuel cycles in the WWER-440 reactors, the results of experimental operation of the new fuel design and the main neutronic characteristics of the core. (Authors)

Development of new chemical and electrochemical decontamination methods for selected equipment of WWER-440 and WWER-1000 reactor primary circuit

International Nuclear Information System (INIS)

Solcanyi, M.; Majersky, D.

1998-01-01

Special devices for in-situ application of decontamination technologies assigned for Steam Generator, Pressurizer and Main Circulating Casing of WWER-1000 type were designed, manufactured and tested in real conditions of their use in above Primary Circuit components. New decontamination technologies like low-concentration process NP-NHN for the decontamination of the Steam Generator, combined chemico-mechanical treatment for the Pressurizer and semi-dry electrolysis for the Main Circulating Pump Casing were developed and approved for their safe plant application from point of view of decontamination efficiency, corrosion influence and processing of secondary wastes. Main technological parameters were defined to achieve high decontamination efficiency and corrosion-safe application of all decontamination technologies. (author)

Simulation of the dynamic behaviour of the secondary circuit of a WWER-440 type nuclear power plant Pt. 1

International Nuclear Information System (INIS)

Gacs, A.; Janosy, J.S.; Kiss, Zs.

1987-07-01

This report describes the simulation model of the secondary circuit of a WWER-440 type nuclear power plant. The goal of this modelling is to simulate normal and small abnormal transients in a Basic Principles Simulator. The earlier reports describing the dynamic simulation of primary circuit of a WWER-440 nuclear power plant are KFKI--1983-127 and KFKI--1985-08. At present the controllers of the secondary circuit are not simulated. Finally, some simulation results are presented. (author)

Part-task simulator for a WWER-440 nuclear power plant subsystem

International Nuclear Information System (INIS)

Szabo, B.K.

1988-07-01

PC-based part-task simulators for simulating subsystems of nuclear power plants are low cost tools for operator training. In the Central Research Institute for Physics, Budapest, a simulator system has been developed to facilitate fast development of such simulators. The first application simulates the Neutron Flux Monitoring System of WWER-440 nuclear power plants. (author) 9 refs.; 2 figs

Experience from operation of WWER-440 model 213 nuclear power plants. Reference plant: Bohunice V2 (Slovakia). Report of the IAEA technical co-operation project RER/9/004 on evaluation of safety aspects of WWER-440 model 213 nuclear power plants

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-07-01

This TECDOC provides a comprehensive review of the operational experience with WWER-440/213 plants. It is hoped that it will be useful to anyone working in the field of WWER safety, and in particular to experts planning, executing or reviewing studies related to the subject. Refs, figs and tabs.

Experience from operation of WWER-440 model 213 nuclear power plants. Reference plant: Bohunice V2 (Slovakia). Report of the IAEA technical co-operation project RER/9/004 on evaluation of safety aspects of WWER-440 model 213 nuclear power plants

International Nuclear Information System (INIS)

1995-07-01

This TECDOC provides a comprehensive review of the operational experience with WWER-440/213 plants. It is hoped that it will be useful to anyone working in the field of WWER safety, and in particular to experts planning, executing or reviewing studies related to the subject. Refs, figs and tabs

Criticality safety and shielding analysis of WWER-440 fuel configurations

International Nuclear Information System (INIS)

Christoskov, I.

2008-01-01

An overview is made of some studies performed on the criticality safety and radiation shielding analysis of irradiated WWER-440 fuel storage and handling configurations. The analytical tools are based on the SCALE 4.4a code system, in combination with the TORT discrete ordinates transport code and the BUGLE-96 cross-sections library. The accuracy of some important results is assessed through comparison with independent evaluations and with measurement data. (author)

Data presentation in the WWER-440 Basic Principle Simulator

International Nuclear Information System (INIS)

Bota, J.; Gossanyi, A.; Vegh, E.

1986-09-01

At the Central Research Institute for Physics, Budapest, Hungary, a Basic Principle Simulator for WWER-440 nuclear power plants is under development. The input/output subsystem of the simulator is described. This subsystem is a control desk-shaped special periphery representing each main parameter of the model. During development special attention was paid to the hardware support of the controllers as this part of the model is regarded as most time consuming. A short summary on the hardware configuration of the simulator is also presented. (author)

Local linear heat rate ramps in the WWER-440 transient regimes

International Nuclear Information System (INIS)

Brik, A.N.; Bibilashvili, Ju.L.; Bogatyr, S.M.; Medvedev, A.V.

1998-01-01

The operation of the WWER-440 reactors must be accomplished in such a way that the fuel rods durability would be high enough during the whole operation period. The important factors determining the absence of fuel rod failures are the criteria limiting the core characteristics (fuel rod and fuel assembly power, local linear heat rate, etc.). For the transient and load follow conditions the limitations on the permissible local linear rate ramp are also introduced. This limitation is the result of design limit of stress corrosion cracking of the fuel cladding and depends on the local fuel burn-up. The control rod motion is accompanied by power redistribution, which, in principle, can result in violating the design and operation limitations. Consequently, this motion have to be such as the core parameters, including the local ramps of the linear heat generation rates would not exceed the permissible ones.The paper considers the problem of WWER-440 reactor control under transient and load follow conditions and the associated optimisation of local linear heat generation rate ramps. The main factors affecting the solution of the problem under consideration are discussed. Some recommendations for a more optimal reactor operation are given.(Author)

Experimental design verification of WWER-440 model 213 nuclear power plants. Reference plant: Bohunice V2 (Slovakia). Report of the IAEA technical co-operation project RER/9/004 on evaluation of safety aspects of WWER-440 model 213 nuclear power plants

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-07-01

This publication addresses the experimental research supporting the design of WWER-440 model 213 plants. it is hoped that the material presented will be useful for experts working in the field of WWER safety, and in particular to those planning, executing or reviewing studies related to the subject. Refs, figs and tabs.

Experimental design verification of WWER-440 model 213 nuclear power plants. Reference plant: Bohunice V2 (Slovakia). Report of the IAEA technical co-operation project RER/9/004 on evaluation of safety aspects of WWER-440 model 213 nuclear power plants

International Nuclear Information System (INIS)

1995-07-01

This publication addresses the experimental research supporting the design of WWER-440 model 213 plants. it is hoped that the material presented will be useful for experts working in the field of WWER safety, and in particular to those planning, executing or reviewing studies related to the subject. Refs, figs and tabs

Temperature and velocity field of coolant at inlet to WWER-440 core - evaluation of experimental data

International Nuclear Information System (INIS)

Jirous, F.; Klik, F.; Janeba, B.; Daliba, J.; Delis, J.

1989-01-01

Experimentally determined were coolant temperature and velocity fields at the inlet of the WWER-440 reactor core. The accuracy estimate is presented of temperature measurements and the relation is given for determining the resulting measurement error. An estimate is also made of the accuracy of solution of the system of equations for determining coefficients B kn using the method of the least square fit. Coefficients B kn represent the relative contribution of the mass flow of the k-th fuel assembly from the n-th loop and allow the calculation of coolant temperatures at the inlet of the k-th fuel assembly, when coolant temperatures in loops at reactor inlet are known. A comparison is made of the results of measurements on a hydrodynamic model of a WWER-440 reactor with results of measurements made at unit 4 of the Dukovany nuclear power plant. Full agreement was found for 32 model measurements and 6 reactor measurements. It may be assumed that the results of other model measurements obtained for other operating variants will also apply for an actual reactor. Their applicability may, however, only be confirmed by repeating the experiment on other WWER-440 reactors. (Z.M.). 5 figs., 7 refs

Reactor noise analysis applications and systems in WWER-440 and WWER-1000 type PWRs

International Nuclear Information System (INIS)

Por, G.

1998-01-01

This paper presents an introduction on different types of well selected noise diagnostic methods with their occurrence in WWER reactors with an analysis of their impact on operational safety and aging which affects the installations safety as well. The main objective is to attract the attention of NPP management staff dealing with safety, safety culture, maintenance, operation and quality assurance proving that such methods can give benefit not only to economy but impact safety of nuclear installations

Approaches for accounting and prediction of fast neutron fluence on WWER pressure vessels and results of validation of calculational procedure

International Nuclear Information System (INIS)

Borodkin, P.G.; Khrennikov, N.N.; Ryabinin, Yu.A.; Adeev, V.A.

2015-01-01

A description is given of the universal procedure for calculation of fast neutron fluence (FNF) on WWER vessels. Approbation of the calculation procedure was carried out by comparing the calculation results for this procedure and measurements on the outer surface of the WWER-440 and WWER-1000 vessels. In addition, an estimation of the uncertainty of the settlement procedure was made in accordance with the requirements of regulatory documents. The developed procedure is applied at Kola NPP for independent fast neutron fluence estimates on the WWER-440 reactor vessels when planning core loads taking into account the introduction of new fuels. The results of the pilot operation of the procedure for calculating FNF at the Kola NPP were taken into account when improving the procedure and its application to the calculations of FNF on the WWER-1000 vessels [ru

Refurbishing the reactor protection systems of VVER-440/230 and VVER-1000/320 nuclear power plants with exclusively digital IandC systems

International Nuclear Information System (INIS)

Martin, M.

1997-01-01

The refurbishment of reactor protection systems of nuclear power plants is based on two sets of requirements: engineering aspects such as performance, qualification and licensing, as well as interfaces to other systems; and cost-benefit relationships, ease of service and maintenance as well as installation during scheduled outages. A number of WWER-440 and WWER-1000 nuclear plants have announced their intention to refurbish their protection systems. Since 1994, these plants have been placing orders with Siemens for new protection systems, including the neutron flux monitoring system utilizing the advanced system TELEPERM XS. This exclusively digital IandC system provides an excellent foundation for the remaining plant service life

An investigation of axial xenon stability in WWER-1000 reactor designs

International Nuclear Information System (INIS)

Doshi, P.K.; Miller, R.W.

1993-01-01

The nuclear power plants of the WWER-1000 design have experienced frequent xenon oscillation control problems. In most PWRs, xenon oscillations are largely a problem in the axial direction. An one dimensional core model representative of the WWER-1000 design was set up to examine the controllability of the current design. An investigation of possible improvements to this design was made. There was no indication that xenon oscillations were an inherent problem in WWER-1000 core design. Simple changes to the control rod system coupled with a sound power distribution control strategy that has been proven to be an effective but simple procedure to follow, eliminate xenon control problems. The changes proposed can be implemented in a very cost effective manner. There are no equipment changes needed, existing control rods can be used. Only software changes are required. (Z.S.) 1 tab., 2 figs., 7 refs

Calculation study of the WWER-440 fuel performance for extended burnup

International Nuclear Information System (INIS)

Kujal, J.; Pazdera, F.; Barta, O.

1984-01-01

The results of preliminary calculational study of extended burnup cycling schemes impact on WWER-440 fuel performance are presented. Two high burnup schemes were proposed with three and four cycles, resp. Comparison was made with three cycle reference case. The thermal mechanical analysis was performed with PIN and RELA codes. The values of rod internal pressure, fuel centerline temperatures and fuel-cladding gap are expressed as function of power history. (author)

Nuclear power plants with reactors WWER-1000 type: today and tomorrow; AEhS s WWER-1000: nastoyashchee i budushchee

Energy Technology Data Exchange (ETDEWEB)

Molchanov, V; Biryukov, G; Novak, K [Opytno-Konstruktorskoe Byuro Gidropress, Podol` sk (Russian Federation)

1996-12-31

There are currently 19 NPP units based on WWER-1000 reactors working in Russia, Ukraine and Bulgaria. They are of four types: V-187, V-302, V-338, V-320. The design principles of these reactors comply with regulations of the eighties, and it is necessary to introduce improvements according to the new regulations and to the operation experience gained. Two approaches for safety and efficiency enhancement are described: AS-91 and AS-92. AS-91 implies gradual improvement of the base WWER-1000/V-320 design by incorporation of new design solutions avoiding the need of building large scale models. AS-92 refers to entirely new design which require experimental research by building a full scale models or by using natural stands. The latter approach will be used for NPP projects to be built after year 2000. The main new feature of AS-92 is the addition of passive safety systems to the active ones in order to protect the fuel from damage.

Influence of temperature measurement accuracy and reliability on WWER-440 reactor operation

International Nuclear Information System (INIS)

Petenyi, V.; Ricany, J.

2001-01-01

The WWER-440 reactor power is controlled by coolant heat-up measurements installed on hot and cold circulation loops (enthalpy rise). For power distribution determination the thermocouples installed in reactor vessel above the fuel assemblies are mainly utilised. The paper shortly presents some interesting observations of temperature measurements influencing the reactor power operation of revealed changes in reactor core behaviour. (Authors)

Monitoring of coolant temperature stratification on piping components in WWER-440 NPPs

International Nuclear Information System (INIS)

Hudcovsky, S.; Slanina, M.; Badiar, S.

2001-01-01

The presentation deals with the aims of non-standard temperature measurements installed on primary and secondary circuit in WWER-440 NPPs, explains reasons of coolant temperature stratification on the piping components. It describes methods of the measurements on pipings, range of installation of the temperature measurements in EBO and EMO units and illustrates results of measurements of coolant temperature stratification. (Authors)

Improvement of operational performance and increase of safety of WWER-1000/V-392

International Nuclear Information System (INIS)

Kurakov, Y.A.; Dragunov, Y.G.; Podshibiakin, A.K.; Fil, N.S.; Krushelnitsky, V.N.; Berkovich, V.M.

2001-01-01

The national programme of nuclear power development approved by the Russian Federation Government in 1998 considers the design of WWER-1000/V-392 power unit as a priority project of the new generation NPP with improved operational performances and increased safety. The pilot unit of this design (NVAES-2) is licensed for construction at the Novovoronezh NPP site. The NVAES-2 design is developed on the basis of standard power unit with reactor plant V-320. Twenty units of this type are in operation at the nuclear power plants in Russia, Ukraine and Bulgaria having totally about 270 reactor-years of operation. Two more V-320 units are being commissioned this year at Rostov NPP and Temelin NPP. So, the WWER-1000/V-392 design is as a whole an evolutionary development of the operating standard unit WWER-1000/V-320. Many technical solutions aimed at increase of safety and improvement of operational performance of the plant are implemented in the NVAES-2 design, such as advanced reactor WWER-1000, passive system of residual power removal, passive system of the core flooding under loss-of-coolant accidents, and others. NVAES-2 design refers to a class of advanced light water reactors and corresponds to the international requirements imposed to the nuclear power plants to be put into operation after the year 2000. New V-392 power unit has a good perspective from the view point of extensive implementation in the framework of the nuclear electricity production in Russia. Design decisions on NVAES-2 power unit with WWER-1000/V-392 reactor plant which assure significantly higher safety level and improve economical performance as compared to the operating WWER-1000 units are briefly considered in the present paper. (author)

Performance analysis of WWER-440/230 nuclear power plants

International Nuclear Information System (INIS)

1997-01-01

This report examines one particular design, the WWER-440/230, the first generation of commercial WWERs, essentially comparable to the western PWR. This design was installed widely in eastern Europe with a total of 16 unites being completed in what are now Armenia, Bulgaria, Germany (the former German Democratic Republic) the Slovak Republic and Russia. The plants in Armenia and Germany (the former German Democratic Republic) have been closed down, but particularly in Bulgaria and to a lesser extent the Slovak Republic the remaining plants supply a significant proportion of the electricity of the country and decisions to close them could not be taken lightly. The aim of this report is twofold: first to determine whether the impression given by these good overall performance indicators is confirmed using more detailed indicators covering a wide range of factors; second, to see to what extent good performance can be attributed to the industrial and institutional environment in which these plants were designed, built and operated. Particular attention is paid to identifying factors that may impact the quality of the service provided, especially those factors under management control which can be strongly influenced by current and future policy changes and those factors that are beyond the plant management control but could have influenced the performance of the power plants. Issues concerning the safety of these plants are of considerable importance, but they remain outside the scope of this report. Conclusions and recommendations formulated by the IAEA related to WWER safety are contained in the series of reports prepared in the framework of the Extrabudgetary Programme on WWER Safety. A programme progress report was published in 1994 (IAEA-TECDOC-773). Refs, figs, tabs

Performance analysis of WWER-440/230 nuclear power plants

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-01-01

This report examines one particular design, the WWER-440/230, the first generation of commercial WWERs, essentially comparable to the western PWR. This design was installed widely in eastern Europe with a total of 16 unites being completed in what are now Armenia, Bulgaria, Germany (the former German Democratic Republic) the Slovak Republic and Russia. The plants in Armenia and Germany (the former German Democratic Republic) have been closed down, but particularly in Bulgaria and to a lesser extent the Slovak Republic the remaining plants supply a significant proportion of the electricity of the country and decisions to close them could not be taken lightly. The aim of this report is twofold: first to determine whether the impression given by these good overall performance indicators is confirmed using more detailed indicators covering a wide range of factors; second, to see to what extent good performance can be attributed to the industrial and institutional environment in which these plants were designed, built and operated. Particular attention is paid to identifying factors that may impact the quality of the service provided, especially those factors under management control which can be strongly influenced by current and future policy changes and those factors that are beyond the plant management control but could have influenced the performance of the power plants. Issues concerning the safety of these plants are of considerable importance, but they remain outside the scope of this report. Conclusions and recommendations formulated by the IAEA related to WWER safety are contained in the series of reports prepared in the framework of the Extrabudgetary Programme on WWER Safety. A programme progress report was published in 1994 (IAEA-TECDOC-773). Refs, figs, tabs.

Express diagnostics of WWER fuel rods at nuclear power plants

International Nuclear Information System (INIS)

Pavlov, S.; Amosov, S.; Sagalov, S.; Kostyuchenko, A.

2009-01-01

Higher safety and economical efficiency of nuclear power plants (NPP) call for a continuous design modification and technological development of fuel assemblies and fuel rods as well as optimization of their operating conditions. In doing so the efficiency of new fuel introduction depends on the completeness of irradiated fuel data in many respects as well as on the rapidity and cost of such data obtaining. Standard examination techniques of fuel assemblies (FA) and fuel rods (FR) intended for their use in hot cell conditions do not satisfy these requirements in full extent because fuel assemblies require preliminary cooling at NPP to provide their shipment to the research center. Expenditures for FA transportation, capacity of hot cells and expenditures for the examined fuel handling do not make it possible to obtain important information about the condition of fuel assemblies and fuel rods after their operation. In order to increase the comprehensiveness of primary data on fuel assemblies and fuel rods immediately after their removal from the reactor, inspection test facilities are widely used for these purposes. The inspection test facilities make it possible to perform nondestructive inspection of fuel in the NPP cooling pools. Moreover these test facilities can be used to repair failed fuel assemblies. The ultrasonic testing of failed fuel rods inside the fuel assembly was developed for stands of inspection and repair of TVSA WWER-1000 for the Kalinin NPP and Temelin NPP. This method was tested for eight leaking fuel assemblies WWER-440 and WWER-1000 with a burnup of ∼14 up to 38 MW·day/kgU. The ultrasonic testing proved its high degree of reliability and efficiency. The defectoscopy by means of the pulsed eddy-current method was adapted for the stand of inspection and repair of TVSA WWER-1000 for the Kalinin NPP. This method has been used at RIAR as an express testing method of FR claddings during the post-irradiation examinations of fuel assemblies WWER

Experience of CR and RCCA operation in Ukrainian WWER-1000: Aspects of reliability, safety and economic efficiency

International Nuclear Information System (INIS)

Afanasyev, A.

2000-01-01

The next topics are represented in the paper: A brief history of WWER-1000 control rod (CR) and WWER-1000 rod cluster control assembly (RCCA) design; Evolution of WWER-1000 CR manufacturing technology and design; Experience of RCCA operation; Lifetime extension of WWER-1000 boron carbide CR; WWER-1000 reactor core operation problems due to partial RCCA insertion; Designing and licensing procedures and first operational experience of WWER-1000 RCCA (CR) with a combined absorber 'boron carbide-hafnium' and a chromium-nickel alloy cladding. The main conclusions are: Fuel assembly (FA) bow is the main reason of partial RCCA insertion during reactor core operation. However, the use of the RCCA and its driver bar with increased dead load, alongside with other measures, allow to reduce the probability of incomplete RCCA insertion; The materials used in CRs of RCCA in existing reactor operating modes have been working reliably; The use of hafnium under an appropriate price policy can give certain economic advantages for the Ukrainian NPPs, however, additional research is needed in order to confirm the specific CR physical characteristics and reliability. (author)

Trends and results in In-Core management for the Kozloduy NPP WWER-440 reactors

International Nuclear Information System (INIS)

Haralampieva, Tz.; Antov, A.; Georgieva, N.; Spasova, V.

2001-01-01

The paper presents the experience gained during the design and operation of the last fuel cycles of the four WWER-440/V-230 units at Kozloduy NPP. High efficiency and economy of the fuel utilization requires very precise procedures for fuel in-core management, including calculations and analyses for reloading scheme design, compared with results from operational measurements and fuel cycle efficiency. The paper describes the main stages of implementation of advanced fuel assemblies in the Kozloduy NPP WWER-440 reactors. New advanced fuel has been implemented after the completion of comprehensive neutron-physical, thermal-hydraulic and thermal-mechanical analyses by using advanced computer codes. As a general task of the fuel cycle improvements it is pointed the increasing of the final fuel burnup and decreasing of the number of spent fuel assemblies. Series of calculations and analyses, related to the introducing of the advanced fuel assemblies and improvement of the fuel cycle characteristics have been carried out to guarantee the safe operation and fuel reliability

WWER identification and analysis of dominant factors affecting the fuel failure rates in WWER-1000 units in Czech Republic, Bulgaria, Ukraine and Russia

International Nuclear Information System (INIS)

Evdokimov, I.; Likhanskii, V.; Afanasieva, E.; Kanukova, V.; Kozhakin, A.; Maslova, L.; Chernetskiy, M.; Zborovskii, V.; Sorokin, A.

2015-01-01

The paper reviews the major findings of the study in the frame of the “Zero Failure Rate” project for WWER. The study included analysis and systematization of available data on leaking fuel assemblies found in 2003 through 2014 in WWER-1000 nuclear units in Russia, Ukraine, Czech Republic and Bulgaria. The study was intended to be used in preparation of recommendations and elaboration of corrective measures for enhancement of reliability and decrease of the failure rates for the WWER-1000 fuel. One of the key areas in successful implementation of the industry ‘zero failure’ goal is a challenge of significant increase of inspections of WWER-1000 fuel assemblies. It may be reasonable (with account taken for international experience) to think of development of more effective equipment for prompt fuel inspections & repair in WWER-1000 spent fuel pool. Another challenge is the elaboration of unified fuel inspection guidelines to ensure that limited industry resources are spent in the most productive way. In the frame of this work it may be helpful to implement in practice the criteria for safe removal of defective fuel rods from the leaking FA under repair

Upgrading of existing NPPs with 440 and 1000 MW WWER type pressurized water reactors for severe external loading conditions. Proceedings. Working material. V. 1, 2

Energy Technology Data Exchange (ETDEWEB)

Godoy, A; Gurpinar, A [eds.; International Atomic Energy Agency, Division of Nuclear Installation Safety, Vienna (Austria)

1993-07-01

The Seminar was intended to provide the opportunity for the exchange of updated information concerning the state-of-the-art related to structural safety of the WWER 440 and 1000 MW nuclear power plants operating or under construction in the Russian Federation and several Eastern European countries. Codes and standards, design assumptions, seismic upgrading and requalification activities, recent verification by experimental methods as well as the corresponding reanalysis and reevaluation procedures were included in the scope. Also presented and discussed were the results of recent studies of typical structures and components under seismic loading. The Seminar was divided into five working sessions. Each session consisted of several presentations by invited speakers and extensive discussions. The topic of discussions involved the following: standards used during design phase, input load definitions and criteria, evaluation of as-built conditions and walk down information, site-specific dynamic response of structures based on recent studies and evaluation of results, capacity evaluations of components and systems based on updated acceptance criteria and strengthening concepts, functional qualification of active mechanical and electrical components and systems.

Upgrading of existing NPPs with 440 and 1000 MW WWER type pressurized water reactors for severe external loading conditions. Proceedings. Working material. V. 1, 2

International Nuclear Information System (INIS)

Godoy, A.; Gurpinar, A.

1993-01-01

The Seminar was intended to provide the opportunity for the exchange of updated information concerning the state-of-the-art related to structural safety of the WWER 440 and 1000 MW nuclear power plants operating or under construction in the Russian Federation and several Eastern European countries. Codes and standards, design assumptions, seismic upgrading and requalification activities, recent verification by experimental methods as well as the corresponding reanalysis and reevaluation procedures were included in the scope. Also presented and discussed were the results of recent studies of typical structures and components under seismic loading. The Seminar was divided into five working sessions. Each session consisted of several presentations by invited speakers and extensive discussions. The topic of discussions involved the following: standards used during design phase, input load definitions and criteria, evaluation of as-built conditions and walk down information, site-specific dynamic response of structures based on recent studies and evaluation of results, capacity evaluations of components and systems based on updated acceptance criteria and strengthening concepts, functional qualification of active mechanical and electrical components and systems

Extended analysis of WWER-1000 Charpy test data

International Nuclear Information System (INIS)

Vodenicharov, St.; Kamenova, Tz.

2001-01-01

The aim of this work is to study the embrittlement rate of WWER-1000 RPV weld metal with high Ni content and to determine influence of neutron irradiation on partial energies of ductile crack initiation, stable and unstable crack propagation and post crack arrest. (author)

An application of low leakage loading pattern to reduce fast neutrons. Fluence on WWER-440 reactor pressure vessel in Kozloduy NPP

International Nuclear Information System (INIS)

Haralampieva, Tz.; Antonov, A.; Monev, M.

2001-01-01

The neutron exposure of a reactor pressure vessel (RPV) is one of the key factors that have to be quantified and assess reliably to provide plant life assurance and for an extension to operational life. This paper summarizes the principal methods that are used in core design optimisation for WWER-440 reactors in NPP-Kozloduy in order to reduce flux of fast neutrons at the RPV. Results of fast neutron fluence changes during the all last cycles of units 1-4 with WWER-440 reactors are considered (Authors)

Operational indices of WWER-1000 fuel assemblies and their improvements

Energy Technology Data Exchange (ETDEWEB)

Vasilchenko, I; Demin, E [Opytno-Konstruktorskoe Byuro Gidropress, Podol` sk (Russian Federation)

1994-12-31

The most general design features of WWER-1000 fuel assembly are discussed. The following advantages of design are stated as well as their operational confirmation and occurrences: (1) `packing` density (tight-lattice) of fuel rods within the fuel assemblies; (2) simple handling of fuel assemblies and its small vulnerability; (3) good conditions for coolant mixing; (4) protection of the absorber rods against coolant effect; (5) adaptability to manufacture that provides stable quality. The main operational indices gathered during a ten-year period (1982-1992) at 17 WWER-1000 units in Russia and Ukraine are outlined. Provisions for emergency protection reliability are described. Future directions to improve fuel economy and control rod operability are discussed. 1 fig.

Operational indices of WWER-1000 fuel assemblies and their improvements

International Nuclear Information System (INIS)

Vasilchenko, I.; Demin, E.

1994-01-01

The most general design features of WWER-1000 fuel assembly are discussed. The following advantages of design are stated as well as their operational confirmation and occurrences: 1) 'packing' density (tight-lattice) of fuel rods within the fuel assemblies; 2) simple handling of fuel assemblies and its small vulnerability; 3) good conditions for coolant mixing; 4) protection of the absorber rods against coolant effect; 5) adaptability to manufacture that provides stable quality. The main operational indices gathered during a ten-year period (1982-1992) at 17 WWER-1000 units in Russia and Ukraine are outlined. Provisions for emergency protection reliability are described. Future directions to improve fuel economy and control rod operability are discussed. 1 fig

Co-ordinated research programme on benchmark study for the seismic analysis and testing of WWER-type nuclear power plants. V. 4A. Paks NPP: Analysis/testing. Working material

International Nuclear Information System (INIS)

1995-01-01

The Co-ordinated research programme on the benchmark study for the seismic analysis and testing of WWER-type nuclear power plants was initiated subsequent to the request from representatives of Member States. The conclusions adopted at the Technical Committee Meeting on Seismic Issues related to existing nuclear power plants held in Tokyo in 1991 called for the harmonization of methods and criteria used in Member States in issues related to seismic safety. The Consulltants' Meeting which followed resulted in producing a working document for CRP. It was decided that a benchmark study is the most effective way to achieve the principal objective. Two types of WWER reactors (WWER-440/213 and WWER-1000) were selected as prototypes for the benchmark exercise to be tested on a full scale using explosions and/or vibration generators. The two prototypes are Kozloduy Units 5/6 for WWER-1000 and Paks for WWER-440/213 nuclear power plants. This volume of Working material contains reports on data related to seismic analyses of structures of Paks and Kozloduy reactor buildings and WWER-440/213 primary coolant loops with different antiseismic devices

Co-ordinated research programme on benchmark study for the seismic analysis and testing of WWER-type nuclear power plants. V. 4A. Paks NPP: Analysis/testing. Working material

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-07-01

The Co-ordinated research programme on the benchmark study for the seismic analysis and testing of WWER-type nuclear power plants was initiated subsequent to the request from representatives of Member States. The conclusions adopted at the Technical Committee Meeting on Seismic Issues related to existing nuclear power plants held in Tokyo in 1991 called for the harmonization of methods and criteria used in Member States in issues related to seismic safety. The Consulltants' Meeting which followed resulted in producing a working document for CRP. It was decided that a benchmark study is the most effective way to achieve the principal objective. Two types of WWER reactors (WWER-440/213 and WWER-1000) were selected as prototypes for the benchmark exercise to be tested on a full scale using explosions and/or vibration generators. The two prototypes are Kozloduy Units 5/6 for WWER-1000 and Paks for WWER-440/213 nuclear power plants. This volume of Working material contains reports on data related to seismic analyses of structures of Paks and Kozloduy reactor buildings and WWER-440/213 primary coolant loops with different antiseismic devices.

Power distribution gradients in WWER type cores and fuel failure root causes

Energy Technology Data Exchange (ETDEWEB)

Mikuš, Ján M., E-mail: JanMikus.nrc@hotmail.com

2014-02-15

Highlights: • Power (fission rate) distribution gradients can represent fuel failure root causes. • Positions with above gradients were investigated in WWER type cores on reactor LR-0. • Above gradients were evaluated near core heterogeneities and construction materials. • Results can be used for code validation and fuel failure occurrence investigation. - Abstract: Neutron flux non-uniformity and gradients of neutron current resulting in corresponding power (fission rate) distribution changes can represent root causes of the fuel failure. Such situation can be expected in vicinity of some core heterogeneities and construction materials. Since needed data cannot be obtained from nuclear power plant (NPP), results of some benchmark type experiments performed on light water, zero-power research reactor LR-0 were used for investigation of the above phenomenon. Attention was focused on determination of the spatial power distribution changes in fuel assemblies (FAs): Containing fuel rods (FRs) with Gd burnable absorber in WWER-440 and WWER-1000 type cores, Neighboring the core blanket and dummy steel assembly simulators on the periphery of the WWER-440 standard and low leakage type cores, resp., Neighboring baffle in WWER-1000 type cores, and Neighboring control rod (CR) in WWER-440 type cores, namely (a) power peak in axial power distribution in periphery FRs of the adjacent FAs near the area between CR fuel part and butt joint to the CR absorbing part and (b) decrease in radial power distribution in FRs near CR absorbing part. An overview of relevant experimental results from reactor LR-0 and some information concerning leaking FAs on NPP Temelín are presented. Obtained data can be used for code validation and subsequently for the fuel failure occurrence investigation.

Calculations of fission rate distribution in the core of WWER-1000 mock-up on the LR-0 reactor using alternative methods and comparison with results of measurements

International Nuclear Information System (INIS)

Zaritskiy, S.; Kovalishin, A.; Tsvetkov, T.; Rypar, V.; Svadlenkova, M.

2011-01-01

General review of experimental and calculation researches on WWER-440 and WWER-1000 mock-ups on the reactor LR-0 was introduced on the twentieth Symposium AER. The experimental core fission rate distribution was obtained by means of gamma-scanning of the fuel pins - 140La single peak (1596 keV) measurements and wide energy range (approximately 600-900 keV) measurements. Altogether from 260 to 500 fuel pins were scanned in different experiments. The measurements were arranged in the middle of the fuel (the active part of pin). Pin-to-pin calculations of the WWER-1000 mock-up core fission rate distribution were performed with several codes: Monte Carlo codes MCU-REA/2 and MCNPX with different nuclear data libraries, diffusion code RADAR (63 energy groups library) and code SVL based on Surface Harmonics Method (69 energy groups). Calculated data are compared with experimental ones. The obtained results allow developing the benchmark for core calculations methodologies, evaluating and validating source reliability for the out-of-core (inside and outside pressure vessel) neutron transport calculations. (Authors)

Fuel performance and operation experience of WWER-440 fuel in improved fuel cycle

International Nuclear Information System (INIS)

Gagarinski, A.; Proselkov, V.; Semchenkov, Yu.

2007-01-01

The paper summarizes WWER-440 second-generation fuel operation experience in improved fuel cycles using the example of Kola NPP units 3 and 4. Basic parameters of fuel assemblies, fuel rods and uranium-gadolinium fuel rods, as well as the principal neutronic parameters and burn-up achieved in fuel assemblies are presented. The paper also contains some data concerning the activity of coolant during operation (Authors)

WWER-1000 nuclear fuel manufacturing process at PJSC MSZ

International Nuclear Information System (INIS)

Morylev, A.; Bagdatyeva, E.; Aksenov, P.

2015-01-01

In this report a brief description of WWER-1000 fuel manufacturing process steps at PJSC MSZ as: uranium dioxide powder fabrication; fuel pellet manufacture fuel rod manufacture working assembly and fuel assembly manufacture is given. The implemented innovations are also presented

Draft report of a consultants meeting on core control and protection strategy of WWER-1000 reactors. Extrabudgetary programme on the safety of WWER-1000 NPPs

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-12-07

At the consultants' meeting on the 'Safety of WWER-1000 Model 320 Nuclear Power Plants' organized by the IAEA within the framework of its Extrabudgetary Programme on the Safety of WWER-1000 NPPs, which was held in Vienna, 1-5 June 1992, the problem of core control and protection strategy was identified as an issue of safety concern. Considering the safety importance of this issue, a consultants' meeting on 'Core Control and Protection Strategy for WWER-1000 Reactors' was convened in Vienna in April 1994 attended by 20 international experts in the area of core control and protection in order to review control and protection system design, to compare them with western practices and to recommend corrective measures. The first WWER-1000 NPP was put into operation in 1980 and there are currently 19 units operating. The accumulated operational experience is more than 130 reactor-years. In addition, there are 8 units under various stages of construction. The previous general observations in the area of core control and protection strategy was focused on core design objectives, core design and fuel management, fuel assembly and core component designs, including burnable absorber and control rod designs, core power distribution control strategy, core control and protection system designs and in-core and ex-core instrumentation systems. While core design objectives of WWER-1000 plants are similar to western practices in general, there are important differences on the design limits and regulatory practices followed for the compliance with the design limits. As a result of previous general observations and specific concerns on core control and protection system design, three working groups were formed to further investigate the specific issues and to compile information on safety issues based on design differences between these plants and similar western plants, to identify areas which need further analysis and make recommendations for short-term and long-term corrective

Draft report of a consultants meeting on core control and protection strategy of WWER-1000 reactors. Extrabudgetary programme on the safety of WWER-1000 NPPs

International Nuclear Information System (INIS)

1994-01-01

At the consultants' meeting on the 'Safety of WWER-1000 Model 320 Nuclear Power Plants' organized by the IAEA within the framework of its Extrabudgetary Programme on the Safety of WWER-1000 NPPs, which was held in Vienna, 1-5 June 1992, the problem of core control and protection strategy was identified as an issue of safety concern. Considering the safety importance of this issue, a consultants' meeting on 'Core Control and Protection Strategy for WWER-1000 Reactors' was convened in Vienna in April 1994 attended by 20 international experts in the area of core control and protection in order to review control and protection system design, to compare them with western practices and to recommend corrective measures. The first WWER-1000 NPP was put into operation in 1980 and there are currently 19 units operating. The accumulated operational experience is more than 130 reactor-years. In addition, there are 8 units under various stages of construction. The previous general observations in the area of core control and protection strategy was focused on core design objectives, core design and fuel management, fuel assembly and core component designs, including burnable absorber and control rod designs, core power distribution control strategy, core control and protection system designs and in-core and ex-core instrumentation systems. While core design objectives of WWER-1000 plants are similar to western practices in general, there are important differences on the design limits and regulatory practices followed for the compliance with the design limits. As a result of previous general observations and specific concerns on core control and protection system design, three working groups were formed to further investigate the specific issues and to compile information on safety issues based on design differences between these plants and similar western plants, to identify areas which need further analysis and make recommendations for short-term and long-term corrective

Post mortem investigations of the NPP Greifswald WWER-440 reactor pressure vessels

International Nuclear Information System (INIS)

Schuhknecht, Jan; Viehrig, Hans-Werner; Weiss, Frank-Peter; Rindelhardt, Udo

2008-01-01

The paper presents first results of the post mortem investigations performed at the reactor pressure vessels (RPV) of the Russian WWER-440 type reactors. Trepans were taken from the core weld SN0.1.4 and base metal of the unit 1 RPV. This RPV was annealed after 15 years of operation and operated for two more years. At first the trepan of the core welding seam was investigated by Master Curve (MC) testing. Specimens from 5 locations through the thickness of the welding seam were tested according to ASTM E1921-05. The reference temperature T 0 was calculated with the measured fracture toughness values, K Jc , at brittle failure of the specimen. Generally the K Jc values measured on pre-cracked and side-grooved Charpy size SE(B) specimens of the investigated weld metal follow the course of the Master Curve. The K Jc values show a remarkable scatter. More values than expected lie below the 5% fractile. In addition the MC SINTAP procedure was applied to determine T 0 SINTAP of the brittle fraction of the data set. There are remarkable differences between T 0 and T 0 SINTAP indicating macroscopic inhomogeneous weld metal. The highest T 0 was about 50 C at a distance of 22 mm from the inner surface of the weld. It is 40 K higher compared with T 0 at the inner surface. This is important for the assessment of ductile-to-brittle temperatures measured with sub size Charpy specimens made of weld metal from the inner RPV wall. This material may not represent the most conservative condition. The results presented in this paper show that the Master Curve approach as adopted in the test standard ASTM E1921-05 is applicable to the investigated WWER-440 multilayer weld metal. The results are of direct importance for an advanced WWER-440 RPV integrity assessment. On the other hand the data pool is broadened for a general introduction of the MC based RPV integrity assessment in the national codes. Furthermore general experiences in the cutting of irradiated RPV steels are collected

Post mortem investigations of the NPP Greifswald WWER-440 reactor pressure vessels

Energy Technology Data Exchange (ETDEWEB)

Schuhknecht, Jan; Viehrig, Hans-Werner; Weiss, Frank-Peter; Rindelhardt, Udo [Forschungszentrum Dresden-Rossendorf e.V., Dresden (Germany). Inst. for Safety Research; Keller, Werner [Studsvik GmbH und Co. KG, Stutensee (Germany)

2008-07-01

The paper presents first results of the post mortem investigations performed at the reactor pressure vessels (RPV) of the Russian WWER-440 type reactors. Trepans were taken from the core weld SN0.1.4 and base metal of the unit 1 RPV. This RPV was annealed after 15 years of operation and operated for two more years. At first the trepan of the core welding seam was investigated by Master Curve (MC) testing. Specimens from 5 locations through the thickness of the welding seam were tested according to ASTM E1921-05. The reference temperature T{sub 0} was calculated with the measured fracture toughness values, K{sub Jc}, at brittle failure of the specimen. Generally the K{sub Jc} values measured on pre-cracked and side-grooved Charpy size SE(B) specimens of the investigated weld metal follow the course of the Master Curve. The K{sub Jc} values show a remarkable scatter. More values than expected lie below the 5% fractile. In addition the MC SINTAP procedure was applied to determine T{sub 0}{sup SINTAP} of the brittle fraction of the data set. There are remarkable differences between T{sub 0} and T{sub 0}{sup SINTAP} indicating macroscopic inhomogeneous weld metal. The highest T{sub 0} was about 50 C at a distance of 22 mm from the inner surface of the weld. It is 40 K higher compared with T{sub 0} at the inner surface. This is important for the assessment of ductile-to-brittle temperatures measured with sub size Charpy specimens made of weld metal from the inner RPV wall. This material may not represent the most conservative condition. The results presented in this paper show that the Master Curve approach as adopted in the test standard ASTM E1921-05 is applicable to the investigated WWER-440 multilayer weld metal. The results are of direct importance for an advanced WWER-440 RPV integrity assessment. On the other hand the data pool is broadened for a general introduction of the MC based RPV integrity assessment in the national codes. Furthermore general experiences in

Surveillance specimen programmes for WWER reactor vessels in the Czech Republic

International Nuclear Information System (INIS)

Brynda, J.; Hogel, J.; Brumovsky, M.

2003-01-01

The present state of materials degradation in WWER reactor pressure vessels manufactured in the Czech Republic is highlighted. The standard surveillance program for WWER-440/V-213 type reactors is described and its deficiencies together with the main results obtained are discussed. A new supplementary surveillance program meeting all requirements for PWR type reactors has been developed and launched. An entirely new design was chosen for the surveillance programme for WWER-1000/V-320 type reactor pressure vessels. Materials selection, container design and location as well as the withdrawal plan connected with ex-vessel fluence monitoring are described

Solution of the 'MIDICORE' WWER-1000 core periphery power distribution benchmark by KARATE and MCNP

International Nuclear Information System (INIS)

Temesvari, E.; Hegyi, G.; Hordosy, G.; Maraczy, C.

2011-01-01

The 'MIDICORE' WWER-1000 core periphery power distribution benchmark was proposed by Mr. Mikolas on the twentieth Symposium of AER in Finland in 2010. This MIDICORE benchmark is a two-dimensional calculation benchmark based on the WWER-1000 reactor core cold state geometry with taking into account the geometry of explicit radial reflector. The main task of the benchmark is to test the pin by pin power distribution in selected fuel assemblies at the periphery of the WWER-1000 core. In this paper we present our results (k eff , integral fission power) calculated by MCNP and the KARATE code system in KFKI-AEKI and the comparison to the preliminary reference Monte Carlo calculation results made by NRI, Rez. (Authors)

Status and prospects of WWER in-core fuel management activities

International Nuclear Information System (INIS)

Novikov, A.N.; Pavlov, V.I.; Pavlovichev, A.M.; Proselkov, V.N.; Saprykin, V.V.

1994-01-01

A short review is given of recent extensive calculational and experimental studies carried out in Russia and Bulgaria for WWER fuel cycle modernization. The main activities performed at Kola NPP, Novovoronezh NPP, Kozloduy NPP and Balakovo NPP are outlined. Based on experience gained, the following improvements in the fuel cycle have been introduced: 1) increased fuel burnup; 2) reduced natural uranium consumption and decreased amount of separation work per energy output unit; 3) increased efficiency of the reactor emergency protection; 4) reduced fast neutron flux onto the reactor vessel. The main characteristics of modernized fuel cycles of WWER-440 and WWER-1000 are presented. 4 tabs., 3 figs., 14 refs

Status and prospects of WWER in-core fuel management activities

Energy Technology Data Exchange (ETDEWEB)

Novikov, A N; Pavlov, V I; Pavlovichev, A M; Proselkov, V N; Saprykin, V V [Russian Research Centre Kurchatov Inst., Moscow (Russian Federation)

1994-12-31

A short review is given of recent extensive calculational and experimental studies carried out in Russia and Bulgaria for WWER fuel cycle modernization. The main activities performed at Kola NPP, Novovoronezh NPP, Kozloduy NPP and Balakovo NPP are outlined. Based on experience gained, the following improvements in the fuel cycle have been introduced: (1) increased fuel burnup; (2) reduced natural uranium consumption and decreased amount of separation work per energy output unit; (3) increased efficiency of the reactor emergency protection; (4) reduced fast neutron flux onto the reactor vessel. The main characteristics of modernized fuel cycles of WWER-440 and WWER-1000 are presented. 4 tabs., 3 figs., 14 refs.

Computerization of the nuclear material accounting system for safeguards purposes at nuclear power plants with WWER-440 reactors

International Nuclear Information System (INIS)

Antonov, V.P.; Konnov, Yu.I.; Semenets, A.N.

1983-01-01

The paper sets forth the basic principles underlying nuclear material accounting at nuclear power plants with WWER-440 reactors. It briefly describes the general structure and individual units in a program for computerized accounting. The use of this program is illustrated by the actual accounting data from the fifth unit of the Novovoronezh nuclear power station. The NUMIS program seems to be of interest both for the purposes of IAEA safeguards and for nuclear power plant operators in countries where power plants with WWER-440 reactors subject to IAEA safeguards are either in operation or under construction. The research in question was conducted initially under an IAEA research contract; the system is now being developed further and tested under the IAEA-USSR technical and scientific co-operation programme on safeguards. (author)

Experimental research on safety assurance of advanced WWER fuel cycles

International Nuclear Information System (INIS)

Krainov, Ju.; Kukushkin, Ju.

2002-01-01

The paper presents the results of experimental investigations on substantiation of implementation of a modernized butt joint for the WWER-440 reactor, carried out in the critical test facility 'P' in the RRC 'Kurchatov Institute'. The comparison results of the calculation and experimental data obtained in the physical startup of Volgodonsk NPP-1 with the WWER-1000 are also given. In the implementation of four-year fuel cycle in the WWER-440 with the average enrichment of fuel makeup 3.82% it was solved to conduct experimental research of power distribution in the vicinity of control rod butt junction. Moreover, it was assumed that adequate actions should be applied to eliminate inadmissible power jumps, if necessary. It is not available to measure their values in NPP conditions. Therefore, the power distribution near the butt joint was studied in a 19-rod bank installed in the critical test facility 'P' first for the normal design of the joint when surrounding fuel assemblies enrichment goes up. Then a set of calculation and tests was fulfilled to optimize a butt junction design. On the base of this research the composition of a butt junction was advanced by placing Hf plates into the junction. The effectiveness of modernized butt joint design was experimentally confirmed. In Volgodonsk NPP-1 with WWER-1000 the four-year fuel cycle is being implemented. During the physical startup of the reactor the measurements of the reactivity effects and coefficients were measured at the minimum controlled flux level, and the parameters of a number of critical states were recorded. The data obtained were compared with the calculation. The validity of the certified code package for forecasting the neutronic characteristics of WWER-1000 cores in the implementation of a four year fuel cycle has been supported (Authors)

Verification calculations for the WWER version of the TRANSURANUS code

International Nuclear Information System (INIS)

Elenkov, D.; Boneva, S.; Georgieva, M.; Georgiev, S.; Schubert, A.; Van Uffelen, P.

2006-01-01

The paper presents part of the work performed in the study project 'Research and Development for Licensing of Nuclear Fuel in Bulgaria'. The main objective of the project is to provide assistance for solving technical questions of the fuel licensing process in Bulgaria. One important issue is the extension of the predictive capabilities of fuel performance codes for Russian-type WWER reactors. In the last decade, a series of international projects has been based on the TRANSURANUS fuel performance code: Specific models for WWER fuel have been developed and implemented in the code in the late 90's. In 2000-2003, basic verification work was done by using experimental data of nuclear fuel irradiated in WWER-440 reactors. While the present paper focuses on the analysis of WWER-1000 standard fuel under normal operating conditions, the above study project covers additional tasks: 1) Post-irradiation calculations of ramp tests performed in the DR3 test reactor of the Risoe National Laboratory (five instrumented fuel rods of the Risoe 3 dataset contained in the IFPE database) using the TRANSURANUS code; 2) Compilation of cross-section libraries for isotope evolution calculations in WWER-440 and WWER-1000 fuel assemblies using the ORIGEN-S code; 3) Analysis of current situation and needs for an extension of the curriculum in Nuclear Engineering at the Technical University of Sofia. In this paper the post-irradiation calculations of steady-state irradiation experiments with nuclear fuel for Russian-type WWER-1000 reactors, using the latest release of the TRANSURANUS code (v1m1j03)are presented. Regarding a comprehensive verification of modern fuel performance codes, the burn-up region above 40 MWd/kgU is of increasing importance. A number of new phenomena emerge at high fuel burn-up, implying the need for enlarged databases of postirradiation examinations (PIE). For one fuel assembly irradiated in a WWER-1000 reactor with a rod discharge burn-up between 50 and 55 MWd

WWER-440 control assembly local power peaking investigation on LR-0 reactor

International Nuclear Information System (INIS)

Mikus, J.

2002-01-01

This paper presents information concerning the local power peaking problem induced by the WWER-440 control assembly and the investigation possibilities on the light water, zero power reactor LR-0 at the Nuclear Research Institute (NRI) Rez plc. A brief description is given about the disposable control assembly model, experimental arrangement and conditions on the LR-0 reactor with regard to the earlier performed investigations as well as to the relevant measurements to be realized in the near future.(abstract)

SCK-CEN Contribution to the IAEA Round Robin Exercise on WWER-440 RPV Weld Material Irradiation, Annealing and Re-Embrittlement

International Nuclear Information System (INIS)

Van Walle, E.; Chaouadi, R.; Puzzolante, J.L.; Fabry, A.; Van de Velde, J.

1998-01-01

The contribution of the Belgian Nuclear Research Centre SCK-CEN to the IAEA Round Robin Exercise on WWER-440 RPV weld material is reported. The objective of this contribution is twofold: (1) to gain experience in the field of the testing of WWER-440 steels; (2) to analyse the round-robin data according to in-house developed on used models in order to check their validity and applicability. Results from testing on unirradiated material are reported including data obtained from chemical analysis, Charpy-V impact testing, tensile testing and fracture toughness determination. Finally, irradiation strategies that can be used in the program to obtain irradiated, irradiated-annealed and irradiated-annealed-reirradiated conditions are outlined

Power release estimation inside of a fuel pin neighbouring a WWER-440 control rod

International Nuclear Information System (INIS)

Mikus, J.

2006-01-01

This work presents an estimation of the control rod (CR) influence in the WWER-440 core on the power release inside of a fuel pin neighbouring CR, that can have some consequences due to possible static and cyclic loads, for example fuel pin / fuel assembly bowing. For this purpose detailed (usual) axial power distribution measurements were performed in a WWER-440 type core on the light water, zero-power research reactor LR-0 in fuel pins near to an authentic CR model at zero boron concentration in moderator, modelling the conditions at the end of fuel cycle. To demonstrate the CR influence on power distribution inside of one fuel pin neighbouring CR, results of above measurements were used for estimation of the: 1) Axial power distribution inside of the investigated fuel pin in both opposite positions on its pellets surface that are situated to- and outwards CR and corresponding gradient of the (r, z) - power distribution in above opposite positions and 2) Azimuthal power distributions on pellet surface of the investigated fuel pin in horizontal planes at selected axial coordinates. Similar information can be relevant from the viewpoint of the fuel pin failures occurrence investigation

Neutron physics calculation for WWER-1000 absorber element lifetime determination

International Nuclear Information System (INIS)

Kurakin, K.Yu.; Kushmanov, S.A.

2009-01-01

Absorber element with compound absorber has been operating in WWER-1000 power units since 1995. AE design meets operating organizations requirements for reliability, service life (to 10 years) and safety functions. Extension of AE service life up to 20 - 30 years by the complex of calculation and experimental work is an important problem of WWER new designs development. The paper deals with the issues related to calculation determination of main factors that influence AE service life limitation - neutron flux and fluence onto absorbing and structural materials during extended service life. (Authors)

Expert system GIP-WWER for verification of seismic adequacy of WWER equipment

International Nuclear Information System (INIS)

Masopust, R.

1999-01-01

The aim of this report is to describe the modified Generic Implementation Procedure (GIP) titled GIP-WWER which can be used to verify seismic adequacy of the safe shutdown mechanical and electrical equipment and distribution systems of operating or constructed WWER NPPs, namely WWER-440/213 type. The WWER-GIP procedure was prepared using available information contained in GIP and the experience taken from various seismic inspections and evaluations of WWER type NPPs performed in the last five years

Development of requirements for seismic upgrading of equipment of existing WWER-440 and WWER-1000 type NPPs

International Nuclear Information System (INIS)

Kaznovsky, S.; Ostretsov, I.

1993-01-01

The change in seismology data and safety demands a necessity arose for seismic upgrading of the existing operating NPPs of WWER type which have been originally designed and built without or with simplifies calculations of seismic influences. The paper describes the traditional methods and approaches and calculation-experimental method for examining and ensuring of equipment seismic resistance at the NPPs directly. Method of ground explosions is included as well

Co-ordinated research programme on benchmark study for the seismic analysis and testing of WWER-type nuclear power plants. V. 4D. Paks NPP: Analysis and testing. Working material

International Nuclear Information System (INIS)

1996-01-01

The Co-ordinated research programme on the benchmark study for the seismic analysis and testing of WWER-type nuclear power plants was initiated subsequent to the request from representatives of Member States. The conclusions adopted at the Technical Committee Meeting on Seismic Issues related to existing nuclear power plants held in Tokyo in 1991 called for the harmonization of methods and criteria used in Member States in issues related to seismic safety. The Consulltants' Meeting which followed resulted in producing a working document for CRP. It was decided that a benchmark study is the most effective way to achieve the principal objective. Two types of WWER reactors (WWER-440/213 and WWER-1000) were selected as prototypes for the benchmark exercise to be tested on a full scale using explosions and/or vibration generators. The two prototypes are Kozloduy Units 5/6 for WWER-1000 and Paks for WWER-440/213 nuclear power plants. This volume of Working material contains reports on seismic margin assessment and earthquake experience based methods for WWER-440/213 type NPPs; structural analysis and site inspection for site requalification; structural response of Paks NPP reactor building; analysis and testing of model worm type tanks on shaking table; vibration test of a worm tank model; evaluation of potential hazard for operating WWER control rods under seismic excitation

Accidents during shutdown conditions for NPP with WWER-1000/428

International Nuclear Information System (INIS)

Antropov, H.A.

1996-01-01

This paper considers the effect of such internal initiating events upon safety of the NPP with WWER-1000/428 as boron dilution and loss of residual heat removal at the reduced coolant inventory in the primary circuit. 2 refs

In core-fuel management in approach to equilibrium of WWER-440 reactor; Prelazni rezim iskoriscenja goriva u nuklearnom reaktoru tipa VVER-440

Energy Technology Data Exchange (ETDEWEB)

Marinkovic, N [Boris Kidric Institute of nuclear sciences, Vinca, Belgrade (Yugoslavia)

1978-07-01

For the need of in core fuel management and prediction of fuel cycle costs as well as operating of a nuclear power plant behaviour of main physical parameters and refueling scheme during approach to equilibrium operation are indispensable. An estimation of a refueling scheme during forst six years of exploitation for a commercially proven PWR reactor of WWER-440 type is shown in this paper. (author)

Proceedings of the twenty-first symposium of atomic energy research on WWER physics and reactor safety

International Nuclear Information System (INIS)

Vidovszky, I.

2011-10-01

The present volume contains 61 papers, presented on the twenty-first symposium of atomic energy research, held in Dresden, Germany, 19-23 September 2011. The papers are presented in their original form, i. e. no corrections or modifications were carried out. The content of this volume is divided into thematic groups: Improvement, extension and validation of parameterized few-group libraries for WWER-440 and WWER-1000.

Safety assessment of unit 5 (WWER-440/W-213) of the Greifswald nuclear power station

International Nuclear Information System (INIS)

1992-02-01

The report represents the common results of the program of German-Soviet cooperation in reactor safety and radiation protection. The technical plant and features of type WWER-440/W-213 nuclear power plants, basic legal licensing principles, reactor core and pressurized components, load resulting from accidents, systems engineering, spreading impacts, civil engineering aspects, and the evaluation of operating experience are described. (DG)

Analysis of WWER-440 fuel performance under normal operating conditions

Energy Technology Data Exchange (ETDEWEB)

Gunduz, Oe; Koese, S; Akbas, T [Atomenerjisi Komisyonu, Ankara (Turkey); Colak, Ue [Ankara Nuclear Research and Training Center (Turkey)

1994-12-31

FRAPCON-2 code originally developed for LWR fuel behaviour simulation is used to analyse the WWER-440 fuel rod behaviour at normal operational conditions. The code is capable of utilizing different models for mechanical analysis and gas release calculations. Heat transfer calculations are accomplished through a collocation technique by the method of weighted residuals. Temperature and burnup element properties are evaluated using MATPRO package. As the material properties of Zr-1%Nb used as cladding in WWER-440s are not provided in the code, Zircaloy-4 is used as a substitute for Zr-1%Nb. Mac-Donald-Weisman model is used for gas release calculation. FRACAS-1 and FRACAS-2 models are used in the mechanical calculations. It is assumed that the reactor was operated for 920 days (three consecutive cycles), the burnup being 42000 Mwd/t U. Results of the fuel rod behaviour analysis are given for three axial nodes: bottom node, central node and top node. The variations of the following characteristic fuel rod parameters are studied through the prescribed power history: unmoved gap thickness, gap heat transfer coefficient, fuel axial elongation, cladding axial elongation, fuel centerline temperature and ZrO-thickness at cladding surface. The value of each parameter is calculated as a function of the effective power days for the three nodes by using FRACAS-1 and FRACAS-2 codes for comparison.The results show that calculations with deformable pellet approximation with FRACAS-II model could provide better information for the behaviour of a typical fuel rod. Calculations indicate that fuel rod failure is not observed during the operation. All fuel rod parameters investigated are found to be within the safety limits. It is concluded, however, that for better assessment of reactor safety these calculations should be extended for transient conditions such as LOCA. 1 tab., 10 figs., 4 refs.

Method for determining the outlet temperature of fuel assemblies unsupplied with thermometer in WWER-440 reactors

International Nuclear Information System (INIS)

Miko, S.; Kalya, Z.; Hamvas, I.

1987-09-01

The paper outlines a method for the evaluation of the outlet temperatures of fuel assemblies unsupplied with thermometer in WWER-440 reactors. The process is based on interpolation of directly measured assembly temperatures. A quantitative comparison of the errors of described algorithm to those of standard plant-computer interpolation rutine is also presented. (author)

Determination of fast neutron fluence at WWER-1000 pressure vessel

International Nuclear Information System (INIS)

Valenta, V. et al.

1989-01-01

The influence function method is an effective tool making it possible, by means of tabulated values to rapidly perform three-dimensional calculations of fast neutron fluences for various reactor core loadings and for various nuclear power plant units. The procedure for determining the spatial dependence of the fast neutron fluences in a WWER-1000 pressure vessel is described. For this, the reactor core is divided into sufficiently fine volume elements within which the neutron source can be regarded as coordinate-independent. The influence functions point to a substantial role of sources lying at the reactor core periphery. In WWER-1000 reactors, only 1 or 2 rows of peripheral assemblies are important. The influence function method makes possible a rapid and easy determination of preconditions for the assessment of the residual lifetime of the pressure vessel based on the actual reactor core loadings. (Z.M.). 7 figs., 8 refs

Influence of decontamination of the WWER-440 primary circuit equipment on pressure drop in the reactor

International Nuclear Information System (INIS)

Kritsky, V.; Rodionov, Y.; Beresina, I.

2003-01-01

Over 40 reactor cycles at four WWER-440 type reactors have been analyzed in order to explain the increase of the pressure drop under certain combination of conditions. It is shown that the staff radiation exposure and the dose rate at first circuit segments are inversely correlated with the value of the pressure drop at the reactor, which is connected with the mechanism of redistribution of deposits and radioactive nuclides between the reactor and the rest part of the circuit. The influence of pH T on the formation of the dose rate from equipment and the change of pressure drop in the reactor WWER-440 is studied. The optimal range of pH T values for these parameters is determined to be 6.95-7.05 and these values are within the range of the water chemistry standards. The correlation between the changes of pressure drop and the number of decontaminated steam generators is established. This correlation shows that the pressure drop at the reactor grows with the increase of steam generators decontaminated during a preventive maintenance

Methodology and conclusions of activation calculations of WWER-440 type nuclear power plants

Energy Technology Data Exchange (ETDEWEB)

Babcsány, Boglárka, E-mail: boglarka.babcsany@reak.bme.hu; Czifrus, Szabolcs; Fehér, Sándor

2015-04-01

Highlights: • Activation calculation of two WWER-440 type nuclear power plants. • Detailed description of the applied activation calculation methodology. • Graphical results for total activity and waste index categorization. • General conclusions for activation applicable in the case of PWR reactors. - Abstract: Activation calculations for two nuclear power plants of WWER-440 type have been performed by the authors in order to assist the decommissioning planning by assessing the radioactive inventory present at the time of and at different times after the final shutdown. According to related international literature and studies performed earlier by the authors, considering the activity more than 99% of this inventory is concentrated in the materials directly surrounding the reactor core, where the predominant evolution of radionuclides is generated by neutron induced nuclear reactions. In order to obtain the highest possible accuracy in modelling, three-dimensional Monte Carlo neutron transport calculations were performed. Besides the methods and models applied to these analyses, the paper also summarizes the results that can be generally applied to such nuclear power plant types. At the time of shutdown, the total activity of the stainless steel components is about 6 × 10{sup 16} Bq and 1.3 × 10{sup 17} Bq for the two NPPs considered. The biological shielding concrete constitutes approximately 7 × 10{sup 13} Bq and 1.1 × 10{sup 14} Bq.

Enhanced Westinghouse WWER-1000 fuel design for Ukraine reactors

International Nuclear Information System (INIS)

Dye, M.; Shah, H.

2015-01-01

Westinghouse has completed design, development, and region quantity delivery of an enhanced Westinghouse fuel assembly for WWER-1000 reactors to support continued safe reactor operations. The enhanced design builds on the successful performance of an earlier generation design which has operated in the South Ukraine 3 reactor for multiple cycles without any fuel rod failures. Incorporated design enhancements include a thicker spacer grid outer strap, an enhanced spacer grid outer strap profile to limit the risk for, and impact of, mechanical interaction/interference with coresident fuel, an all Alloy 718 grid structure for improved stability and strength, and improvements to the top and bottom nozzles. Capable of meeting increased lateral loads generated from using a higher axial trip limit for the refueling machine crane, the design was verified by extensive mechanical and thermalhydraulic testing, which included a newly developed fuel assembly-to-fuel assembly handling test rig to assess performance during bounding core loading and unloading conditions. Through these extensive design enhancements and comprehensive testing program, the enhanced WWER-1000 design provides additional performance, handling, and reliability margins for safe reactor operation. (authors)

WWER fuel: Results of post irradiation examination

International Nuclear Information System (INIS)

Markov, D.V.; Smirnov, V.P.; Smirnov, A.V.; Polenok, V.S.; Perepelkin, S.O.; Ivashchenko, A.A.

2006-01-01

Experience in the field of fabrication, operation, testing and post-irradiation examinations (PIE) made it possible to settle the following requirements for a new generation of WWER nuclear fuel: - For WWER-1000 FA, the service life is no less than 5 years, 3 alternative fuel cycles (FC): 12 months x 4 FCs, 12 months x 5 FCs and 18 months x 3 FCs; - For WWER-440 FA, fuel cycle is 12 months x 5 FCs and a part of operating assembly is left for the 6. year; - High fuel burnup - up to 70 MWd/kgU; - Dimensional stability of FA and its components; - FA repairability; - Adaptability of fuel cycles; - Maintenance of maneuvering operating conditions at the NPP; - Reliability of control rod operation; - High serviceability level - FE leakage is no worse than 10-5 l/year. In order to provide the fulfillment of the above-given requirements, designers and production engineers have worked out cumulative measures and engineering solutions, which are introduced in development of a new generation fuel. Currently old design FA-M assemblies provided with steel skeleton are being operated in WWER-1000 reactors at Ukrainian and Bulgarian NPPs. As for Russian NPPs, new-type FAs are operated. These are advanced FAs (AFA), FA-A and FA-2 provided with zirconium alloy skeletons. A design of the second generation of WWER-440 operating assemblies was developed with respect to changes in some geometrical parameters, fastening of FEs in the lower grid (splinting was substituted for collet), usage of reinforcing rib under the lower grid, anti-debris filter and hafnium elements of junction unit as well as hafnium content decrease from 0.05 % mass down to 0.01% mass in zirconium materials. They are basic designs of FAs in order to be introduced in a five-year fuel cycle of WWER-440 NPPs in Czech Republic and Slovakia since 2005 and have got prospects for development. The operating experience of dismountable operating assemblies at the Loviisa NPP, vibration-proof operating assemblies at the

Risk assessment basis for WWER-440 spent nuclear fuel

International Nuclear Information System (INIS)

Lascek, M.; Necas, V.; Darilek, P.

2000-01-01

The most problematic part of nuclear fuel cycle is its back end. Various high level waste management are available or under development (final disposal of spent assemblies in deep repository, reprocessing, partitioning, transmutation,...). Application of any method is connected with production of characteristic high level waste (amount, radio-toxicity, form,...) as well as various risk level for the environment and mankind. Strategy selection should be based on risk analysis also. The paper deals with assessment of risk, that is associated with WWER-440 spent fuel inventory. In order to evaluate the risk, the accumulated amount of the radioactive inventory is calculated and the decay of the long-lived radionuclides is computed by ORIGEN code. Analysis is oriented on calculation of hazard indexes for assessing the relative hazards of actinides, toxic and long-lived radionuclides. (Authors)

Simulator of nuclear power plant with WWER-440 units

International Nuclear Information System (INIS)

Krcek, V.

1985-01-01

The use is discussed of simulators in the training of qualified personnel for the construction and operation of nuclear power plants. Simulators are used for training all activities and thinking processes related to the control of a nuclear reactor in the course of quasi-steady and non-steady states. The development and implementation is summed up of the construction of such a simulator for WWER-440 nuclear power plants. The main parts of the simulator include the unit control room, the computer system, the teacher's workplace and the interface system. The possibility of simulating the functions of the unit for personnel training is based on the description of the behaviour of the simulated object in form of mathematical models of its basic technological subsystems and their interrelations within the range of operating patterns. (J.C.)

Co-ordinated research programme on benchmark study for the seismic analysis and testing of WWER-type nuclear power plants. V. 2. Generic material: Codes, standards, criteria. Working material

International Nuclear Information System (INIS)

1995-01-01

The Co-ordinated research programme on the benchmark study for the seismic analysis and testing of WWER-type nuclear power plants was initiated subsequent to the request from representatives of Member States. The conclusions adopted at the Technical Committee Meeting on Seismic Issues related to existing nuclear power plants held in Tokyo in 1991 called for the harmonization of methods and criteria used in Member States in issues related to seismic safety. The Consulltants' Meeting which followed resulted in producing a working document for CRP. It was decided that a benchmark study is the most effective way to achieve the principal objective. Two types of WWER reactors (WWER-440/213 and WWER-1000) were selected as prototypes for the benchmark exercise to be tested on a full scale using explosions and/or vibration generators. The two prototypes are Kozloduy Units 5/6 for WWER-1000 and Paks for WWER-440/213 nuclear power plants. This volume of Working material contains reports related to generic material, namely codes, standards and criteria for benchmark analysis

Co-ordinated research programme on benchmark study for the seismic analysis and testing of WWER-type nuclear power plants. V. 2. Generic material: Codes, standards, criteria. Working material

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-07-01

The Co-ordinated research programme on the benchmark study for the seismic analysis and testing of WWER-type nuclear power plants was initiated subsequent to the request from representatives of Member States. The conclusions adopted at the Technical Committee Meeting on Seismic Issues related to existing nuclear power plants held in Tokyo in 1991 called for the harmonization of methods and criteria used in Member States in issues related to seismic safety. The Consulltants' Meeting which followed resulted in producing a working document for CRP. It was decided that a benchmark study is the most effective way to achieve the principal objective. Two types of WWER reactors (WWER-440/213 and WWER-1000) were selected as prototypes for the benchmark exercise to be tested on a full scale using explosions and/or vibration generators. The two prototypes are Kozloduy Units 5/6 for WWER-1000 and Paks for WWER-440/213 nuclear power plants. This volume of Working material contains reports related to generic material, namely codes, standards and criteria for benchmark analysis.

Design basis and design features of WWER-440 model 213 nuclear power plants. Reference plant: Bohunice V2 (Slovakia)

International Nuclear Information System (INIS)

1994-05-01

The prime objective of the IAEA Technical Co-operation Project on Evaluation of Safety Aspects of WWER-440 model 213 NPPs is to co-ordinate and to integrate assistance to national organizations in studying selected aspects of safety for the same type of reactors. Consequently, the study integrated the results generated by national activities carried out in the Czech Republic, Hungary, Slovakia and Ukraine and co-ordinated through the IAEA. Valuable assistance in carrying out the tasks was also provided by Bulgaria and Poland. A set of publications is being prepared to present the results of the project. The publications are intended to facilitate the review and utilization of the results of the project. They are also providing assistance in further refinement and/or extension of plant specific safety evaluation of model 213 NPPs. This Technical Document addressing the design basis and safety related design features of WWER-440 model 213 plants is the first of the series to be published. It is hoped that this document will be useful to anyone working in the field of WWER safety, and in particular to experts planning, executing or reviewing studies related to the subject. Refs, 36 figs, tabs

Source convergence problems in the application of burnup credit for WWER-440 fuel

International Nuclear Information System (INIS)

Hordosy, Gabor

2003-01-01

The problems in Monte Carlo criticality calculations caused by the slow convergence of the fission source are examined on an example. A spent fuel storage cask designed for WWER-440 fuel used a sample case. The influence of the main parameters of the calculations is investigated including the initial fission source. A possible strategy is proposed to overcome the difficulties associated by the slow source convergence. The advantage of the proposed strategy that it can be implemented using the standard MCNP features. (author)

Seismic analysis of the safety related piping and PCLS of the WWER-440 NPP

International Nuclear Information System (INIS)

Berkovski, A.M.; Kostarev, V.V.; Schukin, A.J.; Boiadjiev, Z.; Kostov, M.

2001-01-01

This paper presents the results of seismic analysis of Safety Related Piping Systems of the typical WWER-440 NPP. The methodology of this analysis is based on WANO Terms of Reference and ASME BPVC. The different possibilities for seismic upgrading of Primary Coolant Loop System (PCLS) were considered. The first one is increasing of hydraulic snubber units and the second way is installation of limited number of High Viscous Dampers (HVD). (author)

Systems required during and after an earthquake. Summary report. WWER-1000 nuclear power plants

International Nuclear Information System (INIS)

Monette, P.

1995-01-01

The scope of this document is to list the mechanical, instrumentation and electrical components required during and after earthquake, in order to achieve and maintain safe shutdown conditions of a WWER-1000 type nuclear power plant. The main objective pursued in establishing the systems and equipment list is to provide guidance for the design and implementation of the backfits which are necessary to increase seismic resistance of the components required after earthquake. The presented list is established on generic basis, i.e. it is applicable to any specific WWER-1000

Evaluation of WWER-1000 vessel materials fracture toughness

International Nuclear Information System (INIS)

Grinik, Eh.U.; Revka, V.N.; Chirko, L.I.; Chajkovskij, Yu.V.

2007-01-01

The lifetime of WWER-1000-type reactor vessels is finally conditioned by the fracture toughness (crack growth resistance) of RPV materials. Up to now in line with the regulations the fracture toughness is characterized by the critical temperature of brittleness determined by the results of the Charpy specimen impact testing. Such approach is typical for all countries operating the water pressure reactors. However, regulatory approach is known from the western specialists not always to characterize adequately the crack growth resistance of the vessel materials and in some cases to underestimate their characteristics in the reference state that leads to unreasonably high conservatism. Excessive conservatism may lead to the invalid restrictions in the operating modes and the service life of the reactor vessel. Therefore there appeared the necessity to apply another approaches based on the state-of-the-art experimental methods of the fracture mechanics and allowing evaluating the fracture toughness parameters sufficiently. The paper presents the results of the comparison of the regulatory approach and the Master curve approach from the point of view of the adequate determination of the vessel material crack growth resistance parameters. Analysis of the experimental data of the surveillance specimens illustrated the potential possibility of applying the new statistical method for the WWER-1000- type reactor vessel lifetime extension

IAEA meeting report of the consultants' meeting on safety improvements of WWER-440 model 230 nuclear power plants

International Nuclear Information System (INIS)

1998-05-01

In 1992 the identification and ranking of safety issues for WWER-440/230 NPPs were completed. Some 100 safety issues have been identified and ranked according to their safety impact on the plant's defence in depth. The IAEA work was based on a conceptual design review and a series of safety review missions to each one of the four sites (Bohunice, Kozloduy, Novovoronezh and Kola) where WWER-440/230 NPPs were in operation. Results were published by the IAEA in February and May 1992. Since the initial publications the IAEA has continued its activities and conducted a number of follow-up missions and technical visits to the NPP sites to review the status of implementation of safety upgradings. In September of 1994 a Consultants Meeting (CM) was held in Vienna to consolidate all the information available to the AEA. The results of that meeting were included in the report WWER-SC-107. During 1995-1997 further information became available from technical visits conducted by the IAEA at the four sites. Therefore, in February 1998 the IAEA convened a CM in Vienna to prepare an up-to-date report on the status of safety improvements at WWER-440/230 NPPs. This report contains the results of that meeting. It reviews the status of remedial actions implemented at each plant in response to the safety issues originally identified in the IAEA reports and the remaining safety concerns. For convenience the issues are presented under broad titles related to: integrity of barriers (Section 2); performance of basic functions (Section 3); performance of supporting functions (Section 4); internal hazards (Section 5); external hazards (Section 6); accident analysis (Section 7); operational functions (Section 8); Section 9 provides an overview of the results of PSA studies performed and under way. Section 10 provides specific information on the status of Armenia NPP. It is presented separately because the IAEA assistance to this plant was provided in the framework of the national technical co

The relevance of the IFPE Database to the modelling of WWER-type fuel behaviour

International Nuclear Information System (INIS)

Killeen, J.; Sartori, E.

2006-01-01

The aim of the International Fuel Performance Experimental Database (IFPE Database) is to provide, in the public domain, a comprehensive and well-qualified database on zircaloy-clad UO 2 fuel for model development and code validation. The data encompass both normal and off-normal operation and include prototypic commercial irradiations as well as experiments performed in Material Testing Reactors. To date, the Database contains over 800 individual cases, providing data on fuel centreline temperatures, dimensional changes and FGR either from in-pile pressure measurements or PIE techniques, including puncturing, Electron Probe Micro Analysis (EPMA) and X-ray Fluorescence (XRF) measurements. This work in assembling and disseminating the Database is carried out in close co-operation and co-ordination between OECD/NEA and the IAEA. The majority of data sets are dedicated to fuel behaviour under LWR irradiation, and every effort has been made to obtain data representative of BWR, PWR and WWER conditions. In each case, the data set contains information on the pre-characterisation of the fuel, cladding and fuel rod geometry, the irradiation history presented in as much detail as the source documents allow, and finally any in-pile or PIE measurements that were made. The purpose of this paper is to highlight data that are relevant specifically to WWER application. To this end, the NEA and IAEA have been successful in obtaining appropriate data for both WWER-440 and WWER-1000-type reactors. These are: 1) Twelve (12) rods from the Finnish-Russian co-operative SOFIT programme; 2) Kola-3 WWER-440 irradiation; 3) MIR ramp tests on Kola-3 rods; 4) Zaporozskaya WWER-1000 irradiation; 5) Novovoronezh WWER-1000 irradiation. Before reviewing these data sets and their usefulness, the paper touches briefly on recent, more novel additions to the Database and on progress made in the use of the Database for the current IAEA FUMEX II Project. Finally, the paper describes the Computer

Modelling of WWER-440 fuel rod behaviour under operational conditions with the PIN-micro code

International Nuclear Information System (INIS)

Stefanova, S.; Vitkova, M.; Simeonova, V.; Passage, G.; Manolova, M.; Haralampieva, Z.; Scheglov, A.; Proselkov, V.

1997-01-01

The report summarizes the first practical experience obtained by fuel rod performance modelling at the Institute for Nuclear Research and Nuclear Energy, Bulgarian Academy of Sciences. The results of application of the PIN-micro code and the code modification PINB1 for thermomechanical analysis of WWER-440 fuel assemblies (FAs) are presented. The aim of this analysis is to study the fuel rod behaviour of the operating WWER reactors. The performance of two FAs with maximal linear power and varying geometrical and technological parameters is analyzed. On the basis of recent publications on WWER fuel performance modelling at extended burnup, a modified PINB1 version of the standard PIN-micro code is shortly described and applied for the selected FAs. Comparison of the calculated results is performed. The PINB1 version predicts higher fuel temperatures and more adequate FGR rate, accounting for the extended burnup. The results presented in this paper prove the existence of sufficient safety margins, for the fuel performance limiting parameters during the whole considered period of core operation. (author). 8 refs, 16 figs, 1 tab

Modelling of WWER-440 fuel rod behaviour under operational conditions with the PIN-micro code

Energy Technology Data Exchange (ETDEWEB)

Stefanova, S; Vitkova, M; Simeonova, V; Passage, G; Manolova, M [Institute for Nuclear Research and Nuclear Energy, Sofia (Bulgaria); Haralampieva, Z [National Electric Company Ltd., Kozloduy (Bulgaria); Scheglov, A; Proselkov, V [Institute of Nuclear Reactors, RSC Kurchatov Inst., Moscow (Russian Federation)

1997-08-01

The report summarizes the first practical experience obtained by fuel rod performance modelling at the Institute for Nuclear Research and Nuclear Energy, Bulgarian Academy of Sciences. The results of application of the PIN-micro code and the code modification PINB1 for thermomechanical analysis of WWER-440 fuel assemblies (FAs) are presented. The aim of this analysis is to study the fuel rod behaviour of the operating WWER reactors. The performance of two FAs with maximal linear power and varying geometrical and technological parameters is analyzed. On the basis of recent publications on WWER fuel performance modelling at extended burnup, a modified PINB1 version of the standard PIN-micro code is shortly described and applied for the selected FAs. Comparison of the calculated results is performed. The PINB1 version predicts higher fuel temperatures and more adequate FGR rate, accounting for the extended burnup. The results presented in this paper prove the existence of sufficient safety margins, for the fuel performance limiting parameters during the whole considered period of core operation. (author). 8 refs, 16 figs, 1 tab.

Experience and prospects of WWER-1000 reactor spent fuel transport

International Nuclear Information System (INIS)

Kondratyev, A.N.; Yershov, V.N.; Kozlov, Yu.V.; Kosarev, Yu.A.; Ilyin, Yu.V.; Pavlov, M.S.

1989-01-01

The paper deals with the USSR experience in shipping the commercial WWER-1000 reactor spent fuel in TK-10 and TK-13 casks. The cask designs, their basic characteristics and the WWER-1000 spent fuel features are described. An example of calculational/experimental approach in the design of a basket (one of the most important components) for spent fuel assembly (SFA) accommodation in a cask is given. The main problems of future development works are presented in brief. A concept of development of nuclear power industry with the closed fuel cycle is assumed in the Soviet Union, hence the spent nuclear fuel is to be transported from NPPs to reprocessing plants. To transport WWER-1000 spent fuel, the casks of two types were developed. These are: a pilot TK-10 cask of 3t capacity in fuel; a commercial TK-13 cask of ∼6t capacity in fuel. The pilot TK-10 cask is thick-walled (360mm) cylindrical vessel manufactured of steel shells and a bottom welded to each other. The material of the body is carbon steel. There is a steel jacket on the outer side of the cask body and at 120 mm distance off the bottom. On its cylindrical part between the jacket and the body there are T-shaped circular ribs acting as shock-absorbers. The space between the jacket and the body is filled with ethylene glycol solution of 65 degree C crystallization temperature, which functions as a neutron shielding. The TK-10 cask coolant is water or air (nitrogen) at minor excess pressure resulted from FA heatup after the cask sealing

Co-ordinated research programme on benchmark study for the seismic analysis and testing of WWER-type nuclear power plants. V. 5B. Experience data. Working material

International Nuclear Information System (INIS)

1996-01-01

The Co-ordinated research programme on the benchmark study for the seismic analysis and testing of WWER-type nuclear power plants was initiated subsequent to the request from representatives of Member States. The conclusions adopted at the Technical Committee Meeting on Seismic Issues related to existing nuclear power plants held in Tokyo in 1991 called for the harmonization of methods and criteria used in Member States in issues related to seismic safety. The Consulltants' Meeting which followed resulted in producing a working document for CRP. It was decided that a benchmark study is the most effective way to achieve the principal objective. Two types of WWER reactors (WWER-440/213 and WWER-1000) were selected as prototypes for the benchmark exercise to be tested on a full scale using explosions and/or vibration generators. The two prototypes are Kozloduy Units 5/6 for WWER-1000 and Paks for WWER-440/213 nuclear power plants. This volume of Working material contains reports on the effects of Armenia earthquakes on selected power, industry and commercial facilities and seismic functional qualification of active mechanical and electrical components tested on shaking table

Calculation models of pressure wave propagation within the WWER-440 primary circulating loop

International Nuclear Information System (INIS)

Adamik, V.; Tkach, A.

1982-01-01

Computer codes SHOCK, LOVE, BAREL are described that can be used for the study of pressure wave propagation within the reactor and pipeline system during a LOCA as well as for mechanical loads identification in various parts of the system. SHOCK code is applicable to one-dimensional pressure wave propagation analysis in any hydraulic network containing a compressible nonviscous liquid with a constant (within the considered transient process period) density. LOVE code allows to calculate non-symmetrical mechanical loads on the WWER shaft in case of the main circulation pipeline cold branch rupture. BAREL code is an advanced modification of SHOCK code. It is fitted for two-dimensional pressure wave propagation analysing in the downstream section of a pressurised water reactor in case of the main circulation pipeline cold branch rupture. The calculation results for B-213 type WWER-440 reactor are presented that have been obtained under the assumption of perfect structure rigidity [ru

Modernization of WWER-1000 radiation monitoring systems

Energy Technology Data Exchange (ETDEWEB)

Smith, T [General Atomics, San Diego, CA (United States)

1996-12-31

A modernization scheme of the radiation monitoring system for WWER-1000 is proposed. It has a purpose to comply with international standards and to reduce operational and maintenance cost by deleting obsolete components and reducing the number of detector channels. Detailed layouts of I/C system architecture, digital radiation monitoring system (DRAMS) architecture and LRP block diagram are presented. If planned and implemented properly, this program can provide cost savings by reducing time required to access and display data and maintenance cost by deleting obsolete parts and decreasing the number of detector channels. 3 figs.

Modernization of WWER-1000 radiation monitoring systems

International Nuclear Information System (INIS)

Smith, T.

1995-01-01

A modernization scheme of the radiation monitoring system for WWER-1000 is proposed. It has a purpose to comply with international standards and to reduce operational and maintenance cost by deleting obsolete components and reducing the number of detector channels. Detailed layouts of I/C system architecture, digital radiation monitoring system (DRAMS) architecture and LRP block diagram are presented. If planned and implemented properly, this program can provide cost savings by reducing time required to access and display data and maintenance cost by deleting obsolete parts and decreasing the number of detector channels. 3 figs

SEJV2 software package for radiation monitoring system of WWER 440 NPP

International Nuclear Information System (INIS)

Kapisovsky, V.; Jancik, O.; Kubik, I.; Bena, J.

1993-01-01

The main part of the radiation monitoring system at a WWER-440 (213 reactor type) nuclear power plant is the centralized 400-channel monitoring system 'SEJVAL' servicing twin reactor units. The SEJV2 software package is described developed to run on a PC with an IFS2 interface to the SEJVAL radiation monitoring system. It provides enhanced data presentation, record keeping and report generation, thus improving the efficiency of the health physics shift. The system was for the first time implemented at the Jaslovske Bohunice V-2 nuclear power plant with encouraging results. (Z.S.) 3 refs

Calculation of spatial weight functions for WWER-440 ex-core neutron detectors

International Nuclear Information System (INIS)

Csom, Gy.; Czifrus, Sz.; Feher, S.; Berki, T.

2001-01-01

The objective of the work presented in this paper was determination of a spatial weight function for WWER-440 ex-core detectors to be used for the interpretation of reload startup rod drop measurements. In view of the complexity of the geometry of the core as well as the detector, furthermore the presence of a cavity between the vessel and the concrete shield, Monte Carlo calculations were applied. In spite of the fact that in the corresponding literature the use of adjoint methods dominates, in the present case the forward method was chosen and implemented using MCNP4C (Authors)

Experience in lifetime extension of the first generation WWER-440 power units

International Nuclear Information System (INIS)

Medvedev, P.

2002-01-01

In connection with the expiration of the lifetime for the first generation WWER-440 reactors in Russian Federation (Novo Voronezh and Kola NPP), the legal procedures and Life Time Extension (LTE) Program are discussed. The LTE Program includes: development of regulation basis; economic efficiency studies; power unit modernization; power unit comprehensive examination and justification od equipment resource; in-dept safety assessment; operational license acquisition. As a result from the LTE Program the safety level of the unit 3 of the Novo Voronezh NPP is significantly increases, the operational period has been justified and a 5-year license has been issued

A procedure for temperature-stress fields calculation of WWER-1000 primary circuit in PTS event

Energy Technology Data Exchange (ETDEWEB)

Petkov, G [Technical Univ., Dept. Thermal and Nuclear Power Engineering, Sofia (Bulgaria); Groudev, P; Argirov, J [Bulgarian Academy of Science, Inst. for Nuclear Research and Nuclear Energy, Sofia (Bulgaria)

1997-09-01

The paper presents the procedure of an investigation of WWER-1000 primary circuit temperature-stress field by the use of thermohydraulic computation data for a pressurized thermal shock event ``Core overcooling``. The procedure is based on a model of the plane stress state with ideal contact between wall and medium for the calculation. The computation data are calculated on the base of WWER-1000 thermohydraulic model by the RELAP5/MOD3 codes. This model was developed jointly by the Bulgarian and BNL/USA staff to provide an analytical tool for performing safety analysis. As a result of calculations by codes the computation data for temperature field law (linear laws of a few distinguished parts) and pressure of coolant at points on inner surface of WWER-1000 primary circuit equipment are received. Such calculations can be used as a base for determination of all-important load-carrying sections of the primary circuit pipes and vessels, which need further consideration. (author). 7 refs, 2 figs, 2 tabs.

Strategy for assessment of WWER steam generator tube integrity. Report prepared within the framework of the coordinated research project on verification of WWER steam generator tube integrity

International Nuclear Information System (INIS)

2007-12-01

Steam generator heat exchanger tube degradations happen in WWER Nuclear Power Plant (NPP). The situation varies from country to country and from NPP to NPP. More severe degradation is observed in WWER-1000 NPPs than in case of WWER-440s. The reasons for these differences could be, among others, differences in heat exchanger tube material (chemical composition, microstructure, residual stresses), in thermal and mechanical loadings, as well as differences in water chemistry. However, WWER steam generators had not been designed for eddy current testing which is the usual testing method in steam generators of western PWRs. Moreover, their supplier provided neither adequate methodology and criteria nor equipment for planning and implementing In-Service Inspection (ISI). Consequently, WWER steam generator ISI infrastructure was established with delay. Even today, there are still big differences in the eddy current inspection strategy and practice as well as in the approach to steam generator heat exchanger tube structural integrity assessment (plugging criteria for defective tubes vary from 40 to 90% wall thickness degradation). Recognizing this situation, the WWER operating countries expressed their need for a joint effort to develop methodology to establish reasonable commonly accepted integrity assessment criteria for the heat exchanger tubes. The IAEA's programme related to steam generator life management is embedded into the systematic activity of its Technical Working Group on Life Management of Nuclear Power Plants (TWG-LMNPP). Under the advice of the TWG-LMNPP, an IAEA coordinated research project (CRP) on Verification of WWER Steam Generator Tube Integrity was launched in 2001. It was completed in 2005. Thirteen organizations involved in in-service inspection of steam generators in WWER operating countries participated: Croatia, Czech Republic, Finland, France, Hungary, Russian Federation, Slovakia, Spain, Ukraine, and the USA. The overall objective was to

Report of a consultants meeting on backfittings and safety enhancement measures in NPPs with WWER 440/213 reactors. Extrabudgetary programme on the safety of WWER NPPS

International Nuclear Information System (INIS)

1994-01-01

The purpose of this Consultants' Meeting held by the IAEA in Vienna from 11-15 April 1994 within the framework of the Extrabudgetary Programme on WWER Safety was to review and analyze safety issues revealed during operation and through analyses of NPPs with WWER 440/213 reactors. The initial list of safety issues based on the available reports from various studies had been prepared by the IAEA secretariat before the meeting, together with indications of safety enhancement measures proposed in various NPP units. During the meeting, the underlying safety concerns and actual technical status of the plants were discussed and the ranking of the safety issues was considered. 58 refs, 1 tab

Experience in decontamination of the equipment of NPP's with the WWER-440 reactors

International Nuclear Information System (INIS)

Balaban-Irmenin, Yu.V.

1981-01-01

Different methods of decontamination at NPPs are briefly characterized. Decontamination of the removable part of the main circulation pump (MCP) of the WWER-440 reactor is considered as an example of removable equipment decontamination. A design of the decontamination bath of the removable MCP elements and the applied chemical agents are described. A decontamination flowsheet of the Novovoronezh NPP steam generator (SG) is considered as an example of the autonomic decontamination system. The SG decontamination modes, principal flowsheets of a hydromonitor, steam-ejection sprayer and steam-emulsion device are described [ru

Monitoring system for accuracy and reliability characteristics of standard temperature measurements in WWER-440 reactors

International Nuclear Information System (INIS)

Stanc, S.; Repa, M.

2001-01-01

Description of a monitoring system for accuracy and reliability characteristics of standard temperature measurements in WWER-440 reactors and benefits obtained from its use are shown in the presentation. As standard reactor temperature measurement, coolant temperature measurement at fuel assembly outlets and in loops, entered into the In-Reactor Control System , are considered. Such systems have been implemented at two V-230 reactors and are under implementation at other four V-213 reactors. (Authors)

Co-ordinated research programme on benchmark study for the seismic analysis and testing of WWER-type nuclear power plants. V. 4B. Paks NPP: Analysis/testing. Working material

International Nuclear Information System (INIS)

1995-01-01

The Co-ordinated research programme on the benchmark study for the seismic analysis and testing of WWER-type nuclear power plants was initiated subsequent to the request from representatives of Member States. The conclusions adopted at the Technical Committee Meeting on Seismic Issues related to existing nuclear power plants held in Tokyo in 1991 called for the harmonization of methods and criteria used in Member States in issues related to seismic safety. The Consulltants' Meeting which followed resulted in producing a working document for CRP. It was decided that a benchmark study is the most effective way to achieve the principal objective. Two types of WWER reactors (WWER-440/213 and WWER-1000) were selected as prototypes for the benchmark exercise to be tested on a full scale using explosions and/or vibration generators. The two prototypes are Kozloduy Units 5/6 for WWER-1000 and Paks for WWER-440/213 nuclear power plants. This volume of Working material contains reports on dynamic study of the main building of the Paks NPP; shake table investigation at Paks NPP and the Final report of the Co-ordinated Research Programme

Co-ordinated research programme on benchmark study for the seismic analysis and testing of WWER-type nuclear power plants. V. 1. Data related to sites and plants: Paks NPP, Kozloduy NPP. Working material

International Nuclear Information System (INIS)

1995-01-01

The Co-ordinated research programme on the benchmark study for the seismic analysis and testing of WWER-type nuclear power plants was initiated subsequent to the request from representatives of Member States. The conclusions adopted at the Technical Committee Meeting on Seismic Issues related to existing nuclear power plants held in Tokyo in 1991 called for the harmonization of methods and criteria used in Member States in issues related to seismic safety. The Consulltants' Meeting which followed resulted in producing a working document for CRP. It was decided that a benchmark study is the most effective way to achieve the principal objective. Two types of WWER reactors (WWER-440/213 and WWER-1000) were selected as prototypes for the benchmark exercise to be tested on a full scale using explosions and/or vibration generators. The two prototypes are Kozloduy Units 5/6 for WWER-1000 and Paks for WWER-440/213 nuclear power plants. This volume of Working material contains reports on data related to sites and NPPs Paks and Kozloduy

Co-ordinated research programme on benchmark study for the seismic analysis and testing of WWER-type nuclear power plants. V. 1. Data related to sites and plants: Paks NPP, Kozloduy NPP. Working material

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-07-01

The Co-ordinated research programme on the benchmark study for the seismic analysis and testing of WWER-type nuclear power plants was initiated subsequent to the request from representatives of Member States. The conclusions adopted at the Technical Committee Meeting on Seismic Issues related to existing nuclear power plants held in Tokyo in 1991 called for the harmonization of methods and criteria used in Member States in issues related to seismic safety. The Consulltants' Meeting which followed resulted in producing a working document for CRP. It was decided that a benchmark study is the most effective way to achieve the principal objective. Two types of WWER reactors (WWER-440/213 and WWER-1000) were selected as prototypes for the benchmark exercise to be tested on a full scale using explosions and/or vibration generators. The two prototypes are Kozloduy Units 5/6 for WWER-1000 and Paks for WWER-440/213 nuclear power plants. This volume of Working material contains reports on data related to sites and NPPs Paks and Kozloduy.

Bounding approach in BUC implementation in pool at WWER-440

International Nuclear Information System (INIS)

Havluj, F.

2006-01-01

As new fuel designs (with higher enrichment) are introduced, spent fuel storage facilities might not fulfill criticality safety criteria when using fresh fuel approach to the criticality analyses. Since optimum moderation conditions evaluation even in wet storage systems is required by some regulatory bodies, any credit for soluble boron cannot be taken. Thus, the only suitable way to prove subcriticality of the given spent fuel system with higher enriched/burnt fuel is burnup credit implementation. This paper outlines burnup credit implementation methodology as demonstrated on criticality evaluation of WWER-440 reactor pool at NPP Dukovany. Operational history effects, isotopic set choice, as well as computational issues (SCALE 4.4a was used both for depletion and criticality calculations) are discussed, maintaining strictly conservative approach. Bounding approach in operational history treatment was carefully examined. Criticality evaluation using selection of (as expected) conservative values of operational parameters (specific power, fuel and moderator temperatures, boron content in moderator,..) was compared to criticality evaluation of real fuel assemblies from the NPP database. Therefore, bounding approach was justified and it was shown that it is not excessively conservative. Presented methodology can be applied on any similar spent fuel facility. Suggestions for future research are noted (mainly end-effect evaluation and consideration of profiled fuel) and urgent need of validation of depletion codes for WWER systems is emphasized (Authors)

Long-term WWER-440 dynamics in cyclic power output changes

International Nuclear Information System (INIS)

Petruzela, I.

1989-01-01

Xenon poisoning is one of the main factors limiting the operation of a nuclear power plant with a WWER-440 reactor in the variable load mode, when long-term dynamics applies to cyclic power output changes. An analysis of the xenon poisoning linearized transfer shows that a phase shift of 180deg takes place between the summed-up reactivity change due to a power change and the reactivity change due to xenon poisoning, this for a sine-wave power change with a period of 24 hours. Thus, the requirements are minimized for the change in reactivity of the control elements, and the maximum value can be achieved of released reactivity that can be utilized before the end of the campaign. (B.S.). 6 figs., 4 tabs., 9 refs

Advanced fuel cycles of WWER-1000 reactors

International Nuclear Information System (INIS)

Lunin, G.; Novikov, A.; Pavlov, V.; Pavlovichev, A.

2003-01-01

The present paper considers characteristics of fuel cycles for the WWER-1000 reactor satisfying the following conditions: duration of the campaign at the nominal power is extended from 250 EFPD up to 470 and more ones; fuel enrichment does not exceed 5 wt.%; fuel assemblies maximum burnup does not exceed 55 MWd/kgHM. Along with uranium fuel, the use of mixed Uranium-Plutonium fuel is considered. Calculations were conducted by codes TVS-M, BIPR-7A and PERMAK-A developed in the RRC Kurchatov Institute, verified for the calculations of uranium fuel and certified by GAN RF

Co-ordinated research programme on benchmark study for the seismic analysis and testing of WWER-type nuclear power plants. V. 4C. Paks NPP: Analysis and testing. Working material

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-07-01

The Co-ordinated research programme on the benchmark study for the seismic analysis and testing of WWER-type nuclear power plants was initiated subsequent to the request from representatives of Member States. The conclusions adopted at the Technical Committee Meeting on Seismic Issues related to existing nuclear power plants held in Tokyo in 1991 called for the harmonization of methods and criteria used in Member States in issues related to seismic safety. The Consulltants' Meeting which followed resulted in producing a working document for CRP. It was decided that a benchmark study is the most effective way to achieve the principal objective. Two types of WWER reactors (WWER-440/213 and WWER-1000) were selected as prototypes for the benchmark exercise to be tested on a full scale using explosions and/or vibration generators. The two prototypes are Kozloduy Units 5/6 for WWER-1000 and Paks for WWER-440/213 nuclear power plants. This volume of Working material involves comparative analysis of the seismic analysis results of the reactor building for soft soil conditions, derivation of design response spectra for components and systems; and upper range design response spectra for soft soil site conditions at Paks NPP.

Co-ordinated research programme on benchmark study for the seismic analysis and testing of WWER-type nuclear power plants. V. 4C. Paks NPP: Analysis and testing. Working material

International Nuclear Information System (INIS)

1996-01-01

The Co-ordinated research programme on the benchmark study for the seismic analysis and testing of WWER-type nuclear power plants was initiated subsequent to the request from representatives of Member States. The conclusions adopted at the Technical Committee Meeting on Seismic Issues related to existing nuclear power plants held in Tokyo in 1991 called for the harmonization of methods and criteria used in Member States in issues related to seismic safety. The Consulltants' Meeting which followed resulted in producing a working document for CRP. It was decided that a benchmark study is the most effective way to achieve the principal objective. Two types of WWER reactors (WWER-440/213 and WWER-1000) were selected as prototypes for the benchmark exercise to be tested on a full scale using explosions and/or vibration generators. The two prototypes are Kozloduy Units 5/6 for WWER-1000 and Paks for WWER-440/213 nuclear power plants. This volume of Working material involves comparative analysis of the seismic analysis results of the reactor building for soft soil conditions, derivation of design response spectra for components and systems; and upper range design response spectra for soft soil site conditions at Paks NPP

Standard model of WWER-440 fuel rod for Transuranus and its application for RELAP5 hot channel validation

International Nuclear Information System (INIS)

Hatala, B.; Cvan, M.

2001-01-01

Within the PECO European Commission project of 'Extension of the validation matrix of the TRANSURANUS code' is developed a generic model of WWER-440 fuel rod. The model is intended to be applied for both realistic and licensing, conservative analysis. For such an application the TRANSURANUS code would be complementary tool to generally used system codes, e.g. RELAP5, providing realistic, more detailed insight into processes and safety criteria, relevant to the fuel rod. The paper presents general description of the model for TRANSURANUS code, brief discussion of approaches used in TRANSURANUS and RELAP5 code safety analysis, accompanied with information about RELAP5 model (whole scope unit model, used for licensing analysis). The existing model for RELAP5 code for WWER-440/V-213 Bohunice V2 unit is checked and modified in hot channel part to allow transparent comparison with the TRANSURANUS code. The results from comparison calculations of the both codes are presented for fresh fuel and quasi steady state scenario and are in good agreement, almost identical. These results might be used as a basis for transient analysis

WWER 440/213 NPP containment from the point of view of IAEA requirements and current European practice

International Nuclear Information System (INIS)

Sabata, M.

2000-01-01

In principle, in a NPP three barriers are used to prevent the release of radioactive substances into the environment: the fuel cladding, the primary circuit boundary, and the containment. The presentation deals with the third barrier - the containment, and explains the philosophy of maximum design accident management in the containment of WWER-440/213 NPPs. This type of containment is shown to be an original and fully functional technical solution. Due to the use of the large reserve of the H 3 BO 3 solution and to the active spray systems, an underpressure can be quickly established, thus minimizing any impact of the accident on the environment. The capability of the bubble condenser system for a maximum design accident has been proven by analyses and by tests performed within the framework of PHARE PH 2.13/95: the condenser system can reduce the pressure in the containment in an effective way. The majority of questions arising so far have been answered and the concern resulting from insufficient verification of the system with regard to western standards has been refuted. The WWER-440/213 is fully consistent with IAEA requirements and with current European practice. (A.K.)

WWER-440 local power peaking experiment with/without Hf inserts in the LR-0 reactor

International Nuclear Information System (INIS)

Josek, R.; Hudec, F.; Rypar, V.

2006-01-01

One of the known issues of the WWER-440 reactors is the control rod coupler induced power peaking in the neighbouring fuel assemblies. The effect has been discovered some years ago and is believed to be the cause of several fuel failures during operation in WWER-440 reactors. The effect itself is due to over-moderation and small absorption in the region of control rod coupler, leading to increase in thermal neutron flux and hence to power flare-up in the neighbouring fuel pins. The fuel vendor tackled the problem by attaching hafnium inserts on the inside of the control assembly box. The experiment performed in the LR-0 reactor was focused on the axial and radial power profiles in the vicinity of the control assembly with and without the hafnium inserts. The results of measurements with zero boron concentration are presented. The hafnium insert causes a decrease in peaking factor of about 30% in selected pins close to the control assembly. The measurements are compared with calculations performed with the MCNP-4C code. The compared variables are: the axial fission density distributions; peking factors and peaking factor decrease due to Hf insert. The MCNP results are accurate with respect to the experimental results. A series of benchmarks is being prepared on the basis of these measurements

Simulation of the WWER-440/213 maximum credible accident at the EhNITs stand

International Nuclear Information System (INIS)

Blinkov, V.N.; Melikhov, O.I.; Melikhov, V.I.; Davydov, M.V.; Sokolin, A.V.; Shchepetil'nikov, Eh.Yu.

2000-01-01

The calculations of thermohydraulic processes through the ATHLET code for determining optimal conditions for modeling the coolant leakage at the EhNITs stand by the maximum credible accident at the NPP with WWER-440/213 reactor are presented. The diameters of the nozzle at the stand, whereby the local criterion of coincidence with the data on the NPP (by the maximum flow) and integral criterion of coincidence (by the mass and energy of the coolant, effluent during 10 s) are determined in the process of parametric calculations [ru

Inovation of the computer system for the WWER-440 simulator

International Nuclear Information System (INIS)

Schrumpf, L.

1988-01-01

The configuration of the WWER-440 simulator computer system consists of four SMEP computers. The basic data processing unit consists of two interlinked SM 52/11.M1 computers with 1 MB of main memory. This part of the computer system of the simulator controls the operation of the entire simulator, processes the programs of technology behavior simulation, of the unit information system and of other special systems, guarantees program support and the operation of the instructor's console. An SM 52/11 computer with 256 kB of main memory is connected to each unit. It is used as a communication unit for data transmission using the DASIO 600 interface. Semigraphic color displays are based on the microprocessor modules of the SM 50/40 and SM 53/10 kit supplemented with a modified TESLA COLOR 110 ST tv receiver. (J.B.). 1 fig

Determination of in-service change in the geometry of WWER-1000 core baffle: Calculations and measurements

International Nuclear Information System (INIS)

Margolin, B.Z.; Varovin, A.Y.; Minkin, A.J.; Sorokin, A.A.; Piminov, V.A.; Evdokimenko, V.V.; Fedosovsky, M.E.; Sherstobitov, A.E.; Ovchinnikov, A.G.; Pikulik, S.S.; Erak, D.Y.; Bobkov, A.V.; Timofeev, A.M.; Timokhin, V.I.; Yakushev, S.V.; Vasiliev, V.G.

2015-01-01

The paper gives the basic constitutive equations describing radiation swelling and creep depending on neutron dose, irradiation temperature and triaxial stress state, and justifies these equations experimentally. The WWER-1000 core baffle change in geometry was calculated by different models describing the effect of stresses on radiation swelling. The calculated results are compared with the measured ones for the operating WWER-1000 core baffle at the Balakovo NPP, Unit 1. A method of individual prediction of core baffle geometry change on the basis of the measurement results has been proposed. (authors)

Status and prospects of activities on algorithms and methods in WWER-1000 core control

International Nuclear Information System (INIS)

Filimonov, P.; Krainov, Y.; Proselkov, V.

1994-01-01

On the basis of long-term operational experience and investigations the problems of WWER-1000 reactor control are discussed. Such control is needed for WWER-1000, as well as for its Western analog PWR, for suppressing the axially instable power density field resulted from non-equilibrium redistribution of Xe-135 nuclei in the reactor core. It has been found that an adequate assessment of the reactor state and the prediction of its response to various control actions is essential for the control of power density distribution. For this purpose a computerized operator's adviser with a reactor simulator realizing a physical reactor model based on BIPR-7 code is used. The operation experience of WWER-1000 shows that the available control algorithms allow, with a fair degree of assurance, the prevention of intensive xenon oscillations and the stabilization of the axial offset. But in connection with the renunciation of half-length control rods a new algorithm is under development which makes use of full-length control rods for suppressing the intensive xenon oscillations in the descending phase. A new method based on BIPR-7 and PERMAK codes is also being developed for estimating the value and rate of linear power rating change of the fuel elements in power cycling. 12 figs., 7 refs

Status and prospects of activities on algorithms and methods in WWER-1000 core control

Energy Technology Data Exchange (ETDEWEB)

Filimonov, P; Krainov, Y; Proselkov, V [Russian Research Centre Kurchatov Inst., Moscow (Russian Federation)

1994-12-31

On the basis of long-term operational experience and investigations the problems of WWER-1000 reactor control are discussed. Such control is needed for WWER-1000, as well as for its Western analog PWR, for suppressing the axially instable power density field resulted from non-equilibrium redistribution of Xe-135 nuclei in the reactor core. It has been found that an adequate assessment of the reactor state and the prediction of its response to various control actions is essential for the control of power density distribution. For this purpose a computerized operator`s adviser with a reactor simulator realizing a physical reactor model based on BIPR-7 code is used. The operation experience of WWER-1000 shows that the available control algorithms allow, with a fair degree of assurance, the prevention of intensive xenon oscillations and the stabilization of the axial offset. But in connection with the renunciation of half-length control rods a new algorithm is under development which makes use of full-length control rods for suppressing the intensive xenon oscillations in the descending phase. A new method based on BIPR-7 and PERMAK codes is also being developed for estimating the value and rate of linear power rating change of the fuel elements in power cycling. 12 figs., 7 refs.

Containment leak-tightness enhancement at VVER 440 NPPs

International Nuclear Information System (INIS)

Prandorfy, M.

2000-01-01

The hermetic compartments of WWER 440 NPPs fulfil the function of the containment used at NPPs all over the world. The purpose of the containment is to protect the NPP personnel against radioactive impact as well as to prevent radioactive leakage to the. environ ent during a lost of coolant accident. Leak-tightness enhancement in NPPs with WWER 440/213 and WWER 440/230 reactors is an important safety issue. New procedures, measures and methods were adopted at NPPs in Mochovce, Jaslovske Bohunice, Dukovany and PAKS for leak identification and sealing works performed by VUEZ Levice. (authors)

Structural capacity assessment of WWER-1000 MW reactor containment. Progress report

International Nuclear Information System (INIS)

Jordanov, M.

1999-01-01

The objective of the project is to provide assessment of the structural behaviour and safety capacity of the WWER-1000 MW Reactor Building Containment at Kozloduy NPP under critical combination of loads according to the current international requirements. The analysis is focused on a realistic assessment of the Containment taking into account the non-linear shell behaviour of the pre-stressed reinforced concrete structure. Previous assessments of the status of pre stressing cables pointed out that the efficiency of the Containment as a final defence barrier for internal and external events depends on their reliability. Due to this, the experimental data obtained from embedded sensors (gauges) at pre-stressed shell structure is to be compared with the results from analytical investigations. The reliability of the WWER-1000 MW accident prevention system is under evaluation in the project. The Soviet standard design WWER-1000 MW type units installed in Kozloduy NPP were originally designed for a Safe Shutdown Earthquake (SSE) with a peak ground acceleration (PGA) of 0.1g. The new site seismicity studies revealed that the seismic hazard for the site significantly exceeds the originally estimated and a Review Level Earthquake (RLE) anchored to PGA=0.20g was proposed for re-assessment of the structures and equipment at Kozloduy NPP. The scope of the study is a re-assessment of the Containment structure under critical combination of loads according to the current safety and reliability requirements, including comparison between the Russian design requirements and the international regulations. Additionally, an investigation of the pre-stressing technology and the annual control of the cables' pre-stressing of the Containment is to be made. The crane influence on the dynamic behaviour of the Containment will be done as well as a study of the integrity of the Containment as a final defence barrier

WWER-440/230 reactor pressure vessel integrity. A publication of the extrabudgetary programme on the safety of WWER and RBMK nuclear power plants

International Nuclear Information System (INIS)

1996-08-01

This report was prepared with the objective of integrating all aspects involved and to provide plant specific information on the issue of reactor pressure vessel integrity including pressurized thermal shock assessment. Areas of the thermal hydraulic analysis including selection of transients, of the structural analysis including fracture mechanics assessment and of the material properties including embrittlement, annealing and re-embrittlement behaviour are addressed. The report also provides related recommendations and conclusions as well as detailed information on the plant specific status for operating WWER-440/230 nuclear power plants. 10 refs, 9 figs, 9 tabs

Automatic vibration monitoring system for the diagnostic inspection of the WWER-440 type nuclear power plants

International Nuclear Information System (INIS)

Hollo, E.; Siklossy, P.; Toth, Zs.

1982-01-01

In the Hungarian Research Institute for Electric Power Industry (VEIKI) an automatic vibration monitoring system for diagnostics and inspection of nuclear power plants of type WWER-440 was developed. The paper summarizes the results of this work and investigates the use of mechanical vibrations and oscillations induced by flow for fault diagnosis. The design of the hardware system, the present software possibilities, the laboratory experiments and the guidelines for future software developments are also described in detail. (A.L.)

Vibrodynamical tests of RP equipment with application of imitation area of WWER-1000 reactor

International Nuclear Information System (INIS)

Khajretdinov, V.U.; Tarkhanov, V.V.; Rodionova, I.N.

2015-01-01

Performance of preoperational tests and measurements with application of imitation area of the reactor is a distinctive characteristic of putting into operation of NPP Units with WWER-1000/1200. The imitation area consists of 163 full-scale FA models, where fuel matrixes made of nuclear-fissionable material, are replaced by leaden simulators. Vibrodynamic tests involve inspection of hydrodynamic disturbances in the primary circuit (dynamic impact on the inspected elements), characteristics of vibration response of the main equipment stress-deformed state of bearing structure, and also parameters of moving and geometry of the inspected objects (boundary conditions at process simulation). Preoperational tests and measurements on the simulated area of WWER-1000/1200 are obligatory and performed at every unit of NPP of this type [ru

Implementation of the KASKAD computer code system for WWER-440 at Kozloduy NPP

International Nuclear Information System (INIS)

Antonov, A.; Georgieva, N.; Spasova, V.

2003-01-01

Since 2002 at Kozloduy NPP - EP1 the code package KASKAD is used for WWER-440 reactor core calculations. The main codes entering this package are: BIPR-7A: 3-D diffusion and core analysis code; PERMAK-A: 2-D fine mesh diffusion code. The burnup calculations were performed for all cycles of the Kozloduy NPP Unit 1, Unit 2, Unit 3 and Unit 4. For the last 4-5 cycles of the Units were calculated control rods worth, critical boron concentration at zero power, reactivity coefficients and linear power. These results were analysed and were compared with experimental data. Some results were given in this paper

International workshop on WWER-440 reactor pressure vessel embrittlement and annealing. Working material

International Nuclear Information System (INIS)

1994-01-01

The purpose of the Workshop was essentially to discuss the WWER 440 model 230 reactor pressure vessel integrity in terms of the measures already taken, current activities and future plans. The meeting was arranged in two parts, namely, the Scientific programme followed by the consideration, review and revision of the IAEA Consultancy report on RPV Embrittlement and Annealing. This particular report covers the first part of the meeting i.e., the Scientific Programme, in the form of proceedings of the meeting, while the re-drafted Consultancy report will be issued later. The meeting was attended by sixty-six representatives from thirteen countries. Refs, figs and tabs

Manufacture of rings of 08Kh18N10T sheet for internal structures of WWER type reactors

International Nuclear Information System (INIS)

Fojta, A.; Nitka, B.

1984-01-01

Technology is presented of the manufacture of rings for the jacket, shaft, core catcher and shaft bottom of WWER-440 reactors produced by Vitkovice Steel Works. The rings are manufactured from sheets of austenitic steel 08Kh18N10T. The materials and technology problems are discussed of sheet production, ring welding technology and annealing following welding. The plastic properties are assessed of the welded joints and problems are outlined of ring production for WWER-1000 reactors. (B.S.)

Probabilistic safety assessment of WWER440 reactors prediction, quantification and management of the risk

CERN Document Server

Kovacs, Zoltan

2014-01-01

The aim of this book is to summarize probabilistic safety assessment (PSA) of nuclear power plants with WWER440 reactors and  demonstrate that the plants are safe enough for producing energy even in light of the Fukushima accident. The book examines level 1 and 2 full power, low power and shutdown PSA, and summarizes the author's experience gained during the last 35 years in this area. It provides useful examples taken from PSA training courses the author has lectured and organized by the International Atomic Energy Agency. Such training courses were organised in Argonne National Laboratory (

New requirements for the WWER fuel and their consideration in designing the fuel assemblies

International Nuclear Information System (INIS)

Vasilchenko, I.; Ananyev, Y.

2003-01-01

In 2001-2002 the base designs of the new generation fuel assemblies for the WWER-440 and WWER-1000 reactors were developed. The ways of their further modernisation were defined. The present report deals with the urgent requirements and how they have been implemented in these designs. The assessment of the efficiency of new designs is carried out on the basis of the existing data of the world market on the cost of: Uranium concentrate; dividing operations; fabrication. It is additionally possible also to take into account the cost of transportation, storage and processing of the irradiated fuel including burial of wastes

Stainless steel corrosion in conditions simulating WWER-1000 primary coolant. Corrosion behaviour in mixed core

International Nuclear Information System (INIS)

Krasnorutskij, V.S.; Petel'guzov, I.A.; Gritsina, V.M.; Zuek, V.A.; Tret'yakov, M.V.; Rud', R.A.; Svichkar', N.V.; Slabospitskaya, E.A.; Ishchenko, N.I.

2011-01-01

Research into corrosion kinetics of austenitic stainless steels (06Cr18Ni10Ti, 08Cr18Ni10Ti, 12Cr18Ni10Ti) in medium which corresponds to composition and parameters of WWER-1000 primary coolant with different pH values in autoclave out-pile conditions during 14000 hours is given. Surface of oxide films on stainless steels is investigated. Visual inspection of Westinghouse and TVEL fuel was carried out after 4 cycles in WWER-1000 primary water chemistry conditions at South Ukraine NPP. Westinghouse and TVEL fuel cladding materials possess high corrosion resistance. Blushing of weldments was observed. No visual corrosion defects or deposits were observed on fuel rods.

Analyses and results from standard surveillance programmes of WWER 440/V-213C reactor pressure vessels

Energy Technology Data Exchange (ETDEWEB)

Falcnik, M; Brumovsky, M; Pav, T [Czech Nuclear Society, Prague (Czech Republic)

1994-12-31

In Czech and Slovak republics, six units of WWER 440/C type reactors are monitored by surveillance specimens programmes; the specimens are determined for static tensile testing, impact notch toughness testing and fracture toughness evaluation. Results of mechanical properties of these specimens after irradiation in intervals between 1 and 5 years of operation, are summarized and discussed with respect to the effect of individual heats and welded joints, radiation embrittlement, and annealing recovery. (authors). 3 refs., 11 figs., 2 tabs.

Safety improvement and results of commissioning of Mochovce NPP WWER 440/213

International Nuclear Information System (INIS)

Lipar, M.

1998-01-01

Mochovce NPP is the last one of this kind and compared to its predecessors, it is characterized by several modifications which contribute to the improvement of the safety level. In addition based on Nuclear Regulatory Authority requirements and based on documents: - IAEA - Safety Issues and their ranking for NPP WWER 440/213, - IAEA - Safety Improvement of Mochovce NPP Project Review Mission, - Riskaudit - Evaluation of the Mochovce NPP Safety Improvements. Additional safety measures have been implemented before commissioning. The consortium EUCOM (FRAMATOME - SIEMENS), SKODA Praha, ENERGOPROJEKT Praha, Russian organizations and VUJE Trnava Nuclear Power Plants research institute were selected for design and implementation of the safety measures. The papers summarized, safety requirements, safety measures implemented, results of commissioning and results of safety analysis report evaluation. (author)

Calculation of the local power peaking near WWER-440 control assemblies with Hf plates

International Nuclear Information System (INIS)

Hegyi, Gy.; Hordosy, G.; Kereszturi, A.; Maraszy, Cs.; Temesvari, E.

2003-01-01

The original coupler design of the WWER-440 assemblies had the following well known deficiency: The relatively large amount of water in the coupler between the absorber and fuel port of the control assembly can cause undesirably sharp power peaking in the fuel rods next to the coupler. The power peaking can be especially high after control rod withdrawal when the coupler reached low burnup level region of the adjacent assembly. The modernized coupler design overcomes the original problem by applying a thin Hf plate in the critical region. The very complicated structure of the coupler requires the verification of the core design methods by high precision 3D Monte Carlo calculations. The paper presents an MCNP reference calculation on the control rod coupler benchmark with Hf absorber plates. The benchmark solution with the KARATE-440 code system is also presented. The need for treating the Hf burnout in the reflector region is investigated (Authors)

Development of the temperature field at the WWER-440 core outlet monitoring system and application of the data analyses methods

International Nuclear Information System (INIS)

Spasova, V.; Georgieva, N.; Haralampieva, Tz.

2001-01-01

On-line internal reactor monitoring by 216 thermal couples, located at the reactor core outlet, is carried out during power operation of WWER-440 Units 1 and 2 at Kozloduy NPP. Automatic monitoring of technology process is performed by IB-500MA, which collects and performs initial data processing (discrediting and conversion of analogue signals into digital mode). The paper also presents the results and analyses of power distribution monitoring during the past 21-th and current 22-th fuel cycle at Kozloduy NPP, Unit 1 by using archiving system capacity and related software. The possibility to perform operational assessment and analysis of power distribution in the reactor core in each point of the fuel cycle is checked by comparison of the neutron-physical calculation results with reactor coolant system parameters. Paper shows that the processing and analysis of accumulated significant amount of data in the archive files increases accuracy and reliability of power distribution monitoring in the reactor core in each moment of the fuel cycle of WWER-440 reactors at Kozloduy NPP

Co-ordinated research programme on benchmark study for the seismic analysis and testing of WWER-type nuclear power plants. V. 5A. Experience data. Working material. Experience database of Romanian facilities subjected to the last three Vrancea earthquakes. Final report from November 1994 - October 1995

International Nuclear Information System (INIS)

Coman, O.; Stevenson, J.D.

1996-01-01

The Co-ordinated research programme on the benchmark study for the seismic analysis and testing of WWER-type nuclear power plants was initiated subsequent to the request from representatives of Member States. The conclusions adopted at the Technical Committee Meeting on Seismic Issues related to existing nuclear power plants held in Tokyo in 1991 called for the harmonization of methods and criteria used in Member States in issues related to seismic safety. The Consulltants' Meeting which followed resulted in producing a working document for CRP. It was decided that a benchmark study is the most effective way to achieve the principal objective. Two types of WWER reactors (WWER-440/213 and WWER-1000) were selected as prototypes for the benchmark exercise to be tested on a full scale using explosions and/or vibration generators. The two prototypes are Kozloduy Units 5/6 for WWER-1000 and Paks for WWER-440/213 nuclear power plants. This volume of Working material contains the report experience database for Romanian facilities contingent to the three Vrancea earthquakes

Co-ordinated research programme on benchmark study for the seismic analysis and testing of WWER-type nuclear power plants. V. 5A. Experience data. Working material. Experience database of Romanian facilities subjected to the last three Vrancea earthquakes. Final report from November 1994 - October 1995

Energy Technology Data Exchange (ETDEWEB)

Coman, O [Stevenson and Associates Bucharest Office, Bucharest (Romania); Stevenson, J D [Stevenson and Associates (United States)

1996-07-01

The Co-ordinated research programme on the benchmark study for the seismic analysis and testing of WWER-type nuclear power plants was initiated subsequent to the request from representatives of Member States. The conclusions adopted at the Technical Committee Meeting on Seismic Issues related to existing nuclear power plants held in Tokyo in 1991 called for the harmonization of methods and criteria used in Member States in issues related to seismic safety. The Consulltants' Meeting which followed resulted in producing a working document for CRP. It was decided that a benchmark study is the most effective way to achieve the principal objective. Two types of WWER reactors (WWER-440/213 and WWER-1000) were selected as prototypes for the benchmark exercise to be tested on a full scale using explosions and/or vibration generators. The two prototypes are Kozloduy Units 5/6 for WWER-1000 and Paks for WWER-440/213 nuclear power plants. This volume of Working material contains the report experience database for Romanian facilities contingent to the three Vrancea earthquakes.

Experimental and computation method for determination of burnup and isotopic composition of the WWER-440 fuel using the 134Cs and 137Cs concentrations

International Nuclear Information System (INIS)

Babichev, B.A.; Kozharin, V.V.

1990-01-01

An experimental and computational method for determination of burnup and actinoid concentrations in WWER fuel elements using 134 Cs and 137 Cs concentrations in fuel is considered. It is shown that the error in calculation of fuel burnup and U and Pu isotope concentrations in WWER-440 fuel elements is 1.3-4.9% provided that the error in 134 Cs and 137 Cs concentration measurements does not exceed 1.7 and 1.2%. 9 refs.; 10 figs.; 4 tabs

Statistical analysis of the vibration loading of the reactor internals and fuel assemblies of reactor units type WWER-440 from deferent projects

International Nuclear Information System (INIS)

Ovcharov, O.; Pavelko, V.; Usanov, A.; Arkadov, G.; Dolgov, A.; Molchanov, V.; Anikeev, J.; Pljush, A.

2006-01-01

In this paper the following items have been presented: 1) Vibration noise instrument channels; 2) Vibration loading characteristics of control assemblies, internals and design peculiarities of internals of WWER-440 deferent projects; 3) Coolant flow rate through the reactor, reactor core, fuel assemblies and control assemblies for different projects WWER-440 and 4) Noise measurements of coolant speed per channel. The change of auto power spectrum density of absolute displacement detector signal for the last 12 years of SUS monitoring of the Kola NPP unit 2; the coherence functions groups between two SPND of the same level for the Kola NPP unit 1; the measured coolant flow rate at Paks NPP and the auto power spectrum density group of SPND signals from 11 neutron measuring channels of the Kola NPP unit 1 are given. The main factors of vibration loading of internals and fuel assemblies for Kola NPP units 1-4, Bohunice NPP units 1 and 2 and Novovoronezh NPP units 3 and 4 are also discussed

Investigation of neutron physical features of WWER-440 assembly containing differently enriched pins and Gd burnable poison

International Nuclear Information System (INIS)

Nemes, Imre

2000-01-01

In this paper different pin-distributions of WWER-440 fuel assembly are examined. Assemblies contain 3 Gd-doped pins (Hungarian design), 6 Gd-doped pins near the assembly corners (Russian design) and differently profiled U5-enrichment in different pins. The main neutron physical characteristics of this assemblies - as the function of burnup - are calculated using HELIOS code. The calculated parameters of different assembly designs are analyzed from the standpoint of fuel cycle economy and refueling design practice. (Authors)

Consistent Code Qualification Process and Application to WWER-1000 NPP

International Nuclear Information System (INIS)

Berthon, A.; Petruzzi, A.; Giannotti, W.; D'Auria, F.; Reventos, F.

2006-01-01

Calculation analysis by application of the system codes are performed to evaluate the NPP or the facility behavior during a postulated transient or to evaluate the code capability. The calculation analysis constitutes a process that involves the code itself, the data of the reference plant, the data about the transient, the nodalization, and the user. All these elements affect one each other and affect the results. A major issue in the use of mathematical model is constituted by the model capability to reproduce the plant or facility behavior under steady state and transient conditions. These aspects constitute two main checks that must be satisfied during the qualification process. The first of them is related to the realization of a scheme of the reference plant; the second one is related to the capability to reproduce the transient behavior. The aim of this paper is to describe the UMAE (Uncertainty Method based on Accuracy Extrapolation) methodology developed at University of Pisa for qualifying a nodalization and analysing the calculated results and to perform the uncertainty evaluation of the system code by the CIAU code (Code with the capability of Internal Assessment of Uncertainty). The activity consists with the re-analysis of the Experiment BL-44 (SBLOCA) performed in the LOBI facility and the analysis of a Kv-scaling calculation of the WWER-1000 NPP nodalization taking as reference the test BL-44. Relap5/Mod3.3 has been used as thermal-hydraulic system code and the standard procedure adopted at University of Pisa has been applied to show the capability of the code to predict the significant aspects of the transient and to obtain a qualified nodalization of the WWER-1000 through a systematic qualitative and quantitative accuracy evaluation. The qualitative accuracy evaluation is based on the selection of Relevant Thermal-hydraulic Aspects (RTAs) and is a prerequisite to the application of the Fast Fourier Transform Based Method (FFTBM) which quantifies

Electroerosion cutting of low-sized templets from WWER-1000 type reactor vessel

International Nuclear Information System (INIS)

Neklyudov, I.M.; Ozhigov, L.S.; Gozhenko, S.V.

2012-01-01

The article presents the results of developed method of electroerosion cutting of low-sized templets for the reactor vessel metal composition and structure control in laboratory environment. The article describes the equipment for the remote electroerosive cutting of templets from WWER-1000 type reactor vessel by rigid electrode. The testing results are also shown.

Protection of WWER type primary loops against extreme effects

International Nuclear Information System (INIS)

Podrouzek, J.; Rejent, B.

1985-01-01

Dynamic analyses of the WWER-440 primary loops for the Mochovce nuclear power plant showed that the unprotected primary loop is very soft with a first eigenfrequency of 0.38 Hz. Protection with amortisseurs and viscous shock absorbers was compared and the viscous shock absorber in all cases proved to be more suitable. GERB viscous absorbers will be installed at the Mochovce nuclear power plant. First calculations of the dynamic resistance of the WWER-1000 primary loops for the Temelin nuclear power plant to extreme events were also made. It was shown that the unprotected primary loop is rather soft with a first eigenfrequency of 0.9 Hz, or 0.6 Hz at the pressurizer branch. It will therefore be necessary to protect the primary loops with viscous shock absorbers. (Z.M.)

Saturated steam turbines for power reactors of WWER-type

International Nuclear Information System (INIS)

Czwiertnia, K.

1978-01-01

The publication deals with design problems of large turbines for saturated steam and with problem of output limitations of single shaft normal speed units. The possibility of unification of conventional and nuclear turbines, which creates the economic basis for production of both types of turbines by one manufacturer based on standarized elements and assemblies is underlined. As separate problems the distribution of nuclear district heating power systems are considered. The choice of heat diagram for district heating saturated steam turbines, the advantages of different diagrams and evaluaton for further development are presented. On this basis a program of unified turbines both condensing and district heating type suitable for Soviet reactors of WWER-440 and WWER-1000 type for planned development of nuclear power in Poland is proposed. (author)

Evaluation of radiation exposures to personnel during maintenance operations and fuel recharging at NPP with the WWER-440 reactor

International Nuclear Information System (INIS)

Beskrestnov, N.V.; Vasil'ev, Eh.S.; Kozlov, V.F.; Odinokov, Yu.Yu.; Romanov, V.P.; Tsypin, S.G.

1983-01-01

A unified data acquisition and analysis system is presented. The system is intended to assess radiation exposures to personnel and perform radiation monitoring during periodic maintenance operations sna fuel recharging at NPPs with WWER-440 reactors. The basic principles of developing this system, patterns of danita collection are considered, points of radiation motoring chosen with account of the NPP operating experience are pointed out

Development of WWER-440 fuel. Use of fuel assemblies of 2-nd and 3-rd generations with increased enrichment

International Nuclear Information System (INIS)

Vasilchenko, I.; Lushin, V.; Ananev, U.; Baranov, A.; Kukushkin, U.

2009-01-01

The problem of increasing the power of units at NPPs with WWER-440 is of current importance. There are all the necessary prerequisites for the above-stated problem as a result of updating the design of fuel assemblies and codes. The decrease of power peaking factor in the core is achieved by using profiled fuel assemblies, fuel-integrated burning absorber, FAs with modernized docking unit, modern codes, which allows decreasing conservatism of RP safety substantiation. A wide range of experimental studies of fuel behaviour has been performed which has reached burn-up of (50-60) MW·day/kgU in transition and emergency conditions, post-reactor studies of fuel assemblies, fuel rods and fuel pellets with a 5-year operating period have been performed, which prove high reliability of fuel, presence of a large margin in the fuel pillar, which helps reactor operation at increased power. The results of the work performed on introduction of 5-6 fuel cycles show that the ultimate fuel state on operability in WWER-440 reactors is far from being achieved. Neutron-physical and thermal-hydraulic characteristics of the cores of working power units with RP V-213 are such that actual (design and measured) power peaking factors on fuel assemblies and fuel rods, as a rule, are smaller than the maximum design values. This factor is a real reserve for power forcing. There is experience of operating Units 1, 2, 4 of the Kola NPP and Unit 2 of the Rovno NPP at increased power. Units of the Loviisa NPP are operated at 109 % power. During transfer to work at increased power it is reasonable to use fuel assemblies with increased height of the fuel pillar, which allows decreasing medium linear power distribution. Further development of the 2-nd generation fuel assembly design and consequent transition to working fuel assemblies of the 3-rd generation provides significant improvement of fuel consumption under the conditions of WWER-440 reactors operation with more continuous fuel cycles and

Determination and elimination of the reasons for increased control rod insertion time of the Kozloduy NPP WWER-1000

International Nuclear Information System (INIS)

Nikolov, K.

1996-01-01

The emergency insertion speed of the control rod upon reactor shutdown is of crucial importance for reactor safety. The designed insertion time for WWER-1000 reactors should be in the limits 1,5 to 4 s. Having in mind some data about increased insertion times of WWER-1000 type reactors in Russia and Ukraine, a practice of measuring this parameters during each planned outage of the Kozloduy NPP Unit 6 is introduced. Some technical improvements of the fuel assembly are made in order to reach the nominal parameters of the unit

Safety of reactors built according to earlier standards (WWER 440/V230 type)

International Nuclear Information System (INIS)

Misak, J.; Rohar, S.

1995-01-01

The problems of safety of WWER-440/V-230 type reactors are discussed, and the following conclusions are made. (1) The reactors have a very good operational record. (2) The reactors have serious design shortcomings, which should be eliminated by safety upgrading. Core damage frequency should be further reduced. (3) PSA methods constitute an appropriate tool for assessment of plant vulnerability to some initiating events and malfunctions, for prioritization of upgrading measures and for tolerability of deviations from current safety standards. (4) The most important safety merits, such as a large thermal inertia and low rupture probability, should be properly taken into account in the analysis. (5) Extensive safety upgrading is feasible and can lead to a considerable risk reduction. In certain circumstances such upgrading is the least expensive option even though the total cost is much higher than the initial plant construction cost. (6) Properly upgraded, the reactor units may be operable until better power resources are available within the country. (7) The existing gap between the technological and political judgements of nuclear safety should be reduced continuously by information exchange improvements. (8) A unified approach to nuclear safety should be adopted for all nuclear reactors (not just WWERs) built to earlier standards. 5 tabs., 1 fig

Report of a consultants meeting on draft guidelines for WWER 440/213 containment evaluation

International Nuclear Information System (INIS)

Andrieu, R.; Barre, F.; Birbraer, A.N.

1995-01-01

This report has been prepared at two Consultants' Meetings of experts from France, Germany, Russia, Slovakia, Spain and Ukraine, organized within the framework of the IAEA Extrabudgetary Programme on the Safety of WWER NPPs. In view of the limited time available and the complexity of the task the present report should be treated as a draft, which will be sent to the national regulatory bodies for review and further improvement. The next meeting on the subject will be held in June 1996 with the participation of representatives of all countries operating WWER 440/213 reactors with bubbler condenser containments. During the meeting, the acceptance criteria and review requirements formulated in the IAEA NUSS Series and those in force in the Russian Federation, the United States of America, Germany, France, the Czech Republic, and Slovakia have been taken into consideration. The equivalence of the technical goals which are aimed to be achieved by applying comparable national criteria has been checked in order to avoid multiple addressing the issues and to assure the completeness of the acceptance criteria necessary to assess the design of the containment systems. 48 refs, 12 tabs

Safety issues and their ranking for 'small series' WWER-1000 nuclear power plants. A publication of the extrabudgetary programme on the safety of WWER and RBMK nuclear power plants

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-09-01

This report presents the safety issues in 'small series' WWER-1000 nuclear power plants (NPPs). Safety issues are deviations from current recognized safety practices in design and operation judged to be safety significant by their impact on the plants' defence in depth. This report is intended to serve as reference for the development of plant specific safety improvement programmes and for the evaluation of measures proposed and/or implemented. The identification of safety issues is based on safety studies conducted by the operators of 'small series' WWER-1000 units and by organizations dealing with these reactors, on findings of IAEA safety missions to 'small series' WWER-1000 plants in South Ukraine, at Novovoronezh and Kalinin, and on information obtained from specialists from various countries during an IAEA consultants meeting, 8-12 September 1997 in Vienna, within the framework of the Extra budgetary Programme on the Safety of WWER and RBMK NPPs. Safety issues are first presented according to their impact on the main safety functions and are then described individually. The safety issues are characterized by issue title and specified by issue clarification. Safety issues connected with plant design are followed by the ranking of the issue and ranking justification. Altogether 85 safety issues have been identified, 12 of which are in Category III (defence in depth is insufficient, immediate corrective action is necessary), 38 in Category 11 (defence in depth is degraded, action is needed to resolve the issue) and 22 in Category I (departure from international practices, to be addressed as part of actions to resolve higher priority issues). In the case of operational safety issues (13 safety issues) no ranking is provided as the available material was considered insufficient. For each safety issue, comments and recommendations are made by the IAEA; the status of corresponding measures to improve safety implemented or planned at each site are presented in the

Safety issues and their ranking for 'small series' WWER-1000 nuclear power plants. A publication of the extrabudgetary programme on the safety of WWER and RBMK nuclear power plants

International Nuclear Information System (INIS)

2000-09-01

This report presents the safety issues in 'small series' WWER-1000 nuclear power plants (NPPs). Safety issues are deviations from current recognized safety practices in design and operation judged to be safety significant by their impact on the plants' defence in depth. This report is intended to serve as reference for the development of plant specific safety improvement programmes and for the evaluation of measures proposed and/or implemented. The identification of safety issues is based on safety studies conducted by the operators of 'small series' WWER-1000 units and by organizations dealing with these reactors, on findings of IAEA safety missions to 'small series' WWER-1000 plants in South Ukraine, at Novovoronezh and Kalinin, and on information obtained from specialists from various countries during an IAEA consultants meeting, 8-12 September 1997 in Vienna, within the framework of the Extra budgetary Programme on the Safety of WWER and RBMK NPPs. Safety issues are first presented according to their impact on the main safety functions and are then described individually. The safety issues are characterized by issue title and specified by issue clarification. Safety issues connected with plant design are followed by the ranking of the issue and ranking justification. Altogether 85 safety issues have been identified, 12 of which are in Category III (defence in depth is insufficient, immediate corrective action is necessary), 38 in Category 11 (defence in depth is degraded, action is needed to resolve the issue) and 22 in Category I (departure from international practices, to be addressed as part of actions to resolve higher priority issues). In the case of operational safety issues (13 safety issues) no ranking is provided as the available material was considered insufficient. For each safety issue, comments and recommendations are made by the IAEA; the status of corresponding measures to improve safety implemented or planned at each site are presented in the

Verification of 3-D generation code package for neutronic calculations of WWERs

International Nuclear Information System (INIS)

Sidorenko, V.D.; Aleshin, S.S.; Bolobov, P.A.; Bolshagin, S.N.; Lazarenko, A.P.; Markov, A.V.; Morozov, V.V.; Syslov, A.A.; Tsvetkov, V.M.

2000-01-01

Materials on verification of the 3 -d generation code package for WWERs neutronic calculations are presented. The package includes: - spectral code TVS-M; - 2-D fine mesh diffusion code PERMAK-A for 4- or 6-group calculation of WWER core burnup; - 3-D coarse mesh diffusion code BIPR-7A for 2-group calculations of quasi-stationary WWERs regimes. The materials include both TVS-M verification data and verification data on PERMAK-A and BIPR-7A codes using constant libraries generated with TVS-M. All materials are related to the fuel without Gd. TVS-M verification materials include results of comparison both with benchmark calculations obtained by other codes and with experiments carried out at ZR-6 critical facility. PERMAK-A verification materials contain results of comparison with TVS-M calculations and with ZR-6 experiments. BIPR-7A materials include comparison with operation data for Dukovany-2 and Loviisa-1 NPPs (WWER-440) and for Balakovo NPP Unit 4 (WWER-1000). The verification materials demonstrate rather good accuracy of calculations obtained with the use of code package of the 3 -d generation. (Authors)

Recommended reactor coolant water chemistry requirements for WWER-1000 units with 235U higher enriched fuel

International Nuclear Information System (INIS)

Dobrevski, I.; Zaharieva, N.

2011-01-01

The last decade worldwide experience of PWRs and WWERs confirms the trends for the improvement of the nuclear power industry electricity production through the implementation of high burn-up or high fuel duty, which are usually accompanied with the usage of UO 2 fuel with higher content of 235 U - 4.0% - 4.5% (5.0%). It was concluded that the onset of sub-cooled nucleate boiling (SNB) on the fuel cladding surfaces and the initial excess reactivity of the core are the primary and basic factors accompanying the implementation of uranium fuel with higher 235 U content, aiming extended fuel cycles and higher burn-up of the fuel in Pressurized Water Reactors. As main consequences of the presence of these factors the modifications of chemical / electrochemical environments of nuclear fuel cladding- and reactor coolant system- surfaces are evaluated. These conclusions are the reason for: 1) The determination of the choices of the type of fuel cladding materials in respect with their enough corrosion resistance to the specific fuel cladding environment, created by the presence of SNB; 2) The development and implementation of primary circuit water chemistry guidelines ensuring the necessary low corrosion rates of primary circuit materials and limitation of cladding deposition and out-of-core radioactivity buildup; 3) Implementation of additional neutron absorbers which allow enough decrease of the initial concentration of H 3 BO 3 in coolant, so that its neutralization will be possible with the permitted alkalising agent concentrations. In this paper the specific features of WWER-1000 units in Bulgarian Nuclear Power Plant; use of 235 U higher enriched fuel in the WWER-1000 reactors in the Kozloduy NPP; coolant water chemistry and radiochemistry plant data during the power operation period of the Kozloduy NPP Unit 5, 15 th fuel cycle; evaluation of the approaches and results by the conversion of the WWER-1000 Units at the Kozloduy NPP to the uranium fuel with 4.3% 235 U as

Steam generator and condenser design of WWER-1000 type of nuclear power plant

International Nuclear Information System (INIS)

Zare Shahneh, Abolghasem.

1995-03-01

Design process of steam generator and condenser at Russian nuclear power plant type WWER-1000 is identified. The four chapter of the books are organized as nuclear power plant, types of steam generators specially horizontal steam generator, process of steam generator design and the description of condenser and its process design

Co-ordinated research programme on benchmark study for the seismic analysis and testing of WWER-type nuclear power plants. V. 3E. Kozloduy NPP units 5/6: Analysis/testing. Working material

International Nuclear Information System (INIS)

1996-01-01

The Co-ordinated research programme on the benchmark study for the seismic analysis and testing of WWER-type nuclear power plants was initiated subsequent to the request from representatives of Member States. The conclusions adopted at the Technical Committee Meeting on Seismic Issues related to existing nuclear power plants held in Tokyo in 1991 called for the harmonization of methods and criteria used in Member States in issues related to seismic safety. The Consulltants' Meeting which followed resulted in producing a working document for CRP. It was decided that a benchmark study is the most effective way to achieve the principal objective. Two types of WWER reactors (WWER-440/213 and WWER-1000) were selected as prototypes for the benchmark exercise to be tested on a full scale using explosions and/or vibration generators. The two prototypes are Kozloduy Units 5/6 for WWER-1000 and Paks for WWER-440/213 nuclear power plants. This volume of Working material contains reports on data related to floor response spectra of Kozloduy NPP; calculational-experimental examination and ensuring of equipment and pipelines seismic resistance at starting and operating WWER-type NPPs; analysis of design floor response spectra and testing of the electrical systems; experimental investigations and seismic analysis Kozloduy NPP; testing of components on the shaking table facilities and contribution to full scale dynamic testing of Kozloduy NPP; seismic evaluation of the main steam line, piping systems, containment pre-stressing and steel ventilation chimney of Kozloduy NPP

Full-scale model development of the WWER-440 reactor fuel rod bundle for core temperature regime study under reflooding conditions

International Nuclear Information System (INIS)

Bezrukov, Yu.A.; Logvinov, S.A.; Levchuk, S.V.; Nakladnov, V.D.; Onshin, V.P.; Sokolov, A.S.

1982-01-01

Consideration is given to the issues of a full scale WWER-440 fuel rod bundle imitation. An imitator contains a molybdenum heating rod inclosed in stainless steel shell. The shell diameter is 9 mm, the heated length is 2500 mm, the total len.o.th is 2855 mm. 125 fuel rod imitators are set in the bundle mock-up. The experiments were run on a test facility imitating the WWER-440 reactor primary loop, providing the conditions of the loop breaking. The mock-up thermal hydraulics has been studied during the refloodino. stage. The mock-up was heated up to predetermined initial temperature at a low power level with saturated steam cooling. Then the steam input was stopped, the power level rarapidly rised up to a given value and the cooling water injected. Simultaneously with water injection all the measured parameters monitoring was started. Both at the top spraying and combined cooling temperature oscillations in the upper and middle parts of the mock-up were observed. At the bottom reflooding the mock-up cooling down took more time, thereat temperature inthe upper part first slowly rised during reflooding then decreased and then dropped abruptly at thefront coming up [ru

The summary of WWER-1000 fuel utilization in Ukraine

Energy Technology Data Exchange (ETDEWEB)

Afanasyev, A [Ukrainian State Committee on Nuclear Power Utilization, Kiev (Ukraine)

1997-12-01

The report discusses the status of the fuel and fuel cycles of WWER-1000 reactors in Ukraine. The major reasons that caused the Ukrainian utilities to overcome the conservative design solutions in order to improve fuel utilization and extend fuel burnup are shown. At the same time the sufficient fuel reliability and fuel cycle flexibility are ensured. The burnup distribution in the unloaded fuel assemblies and average fuel rod failure rate are presented. The questions of reactor core operation safety and the economical problems of the front end of the fuel cycle are also considered. (author). 2 refs, 3 figs, 4 tabs.

On steady-state concentrations of ammonia and molecular hydrogen in the primary circuit of the WWER-1000 reactors

International Nuclear Information System (INIS)

Arkhipov, O.P.; Bugaenko, V.L.; Kamakchi, S.A.

1997-01-01

It is shown that the MORAVA-N2 software package describes well the coolant state in the primary circuit of an actual reactor facility with the WWER-1000 during on-load operation. It permits using the package for analysis of process perturbation effect on the coolant composition. Specific feature of ammonia radiation chemistry in the primary circuit of a reactor facility with the WWER-1000, assuring the rates hydrogen concentration in the coolant with ammonia concentration variation in the coolant within wide limits, when reactor operates on power, can be mentioned by way of example, the fact being ascertained in this study

Experience with the WWER-440 MW reactor pressure vessel in-service inspections and evaluation of their results

International Nuclear Information System (INIS)

Brumovsky, M.; Kralovec, J.; Prepechal, J.; Sulc, J.

1989-01-01

The Power Machinery Plant of Skoda Works in Plzen carries out in-service inspections of WWER-440 MW reactor pressure vessels by means of remote controlled inspection equipment - the TRC reactor test system, and some other inspections devices. The results of the in-service inspections were evaluated by methods based on the fracture mechanics approach, the knowledge of stress and strain distribution, and the operating history of the pressure vessels. Examples of types of defects found and their analysis are shown. (author). 1 tab

Substantiation of operation limits of reactivity insertion during WWER-1000 reactors start-up; Obosnovanie ehkspluatatsionnykh predelov vvoda reaktivnosti pri puske reaktorov WWER-1000

Energy Technology Data Exchange (ETDEWEB)

Boev, I; Sabitov, A; Sal` kov, V; Sudarev, O; Yakovlev, A [ATOMTECHENERGO RF, Novovoronezh (Russian Federation)

1996-12-31

The methods and programmes used to define the tolerable rate of reactivity insertion during WWER-1000 start-up are presented. They include calculation of the neutron source power in the core during the sub-critical stage and calculation of the relative neutron density and reactor period during the critical stage. The need for optimisation and regulation of tolerable rates is discussed along with the tool parameters affecting the reactivity during start-up. The possibility of increasing the feed rate of pure condensate into the first loop during the time needed to reach critical stage is justified. 4 refs., 3 tabs.

Electromagnetism Mechanism for Enhancing the Refueling Cycle Length of a WWER-1000

Directory of Open Access Journals (Sweden)

Navid Poursalehi

2017-02-01

Full Text Available Increasing the operation cycle length can be an important goal in the fuel reload design of a nuclear reactor core. In this research paper, a new optimization approach, electromagnetism mechanism (EM, is applied to the fuel arrangement design of the Bushehr WWER-1000 core. For this purpose, a neutronic solver has been developed for calculating the required parameters during the reload cycle of the reactor. In this package, two modules have been linked, including PARCS v2.7 and WIMS-5B codes, integrated in a solver for using in the fuel arrangement optimization operation. The first results of the prepared package, along with the cycle for the original pattern of Bushehr WWER-1000, are compared and verified according to the Final Safety Analysis Report and then the results of exploited EM linked with Purdue Advanced Reactor Core Simulator (PARCS and Winfrith Improved Multigroup Scheme (WIMS codes are reported for the loading pattern optimization. Totally, the numerical results of our loading pattern optimization indicate the power of the EM for this problem and also show the effective improvement of desired parameters for the gained semi-optimized core pattern in comparison to the designer scheme.

Electromagnetism mechanism for enhancing the refueling cycle length of a WWER-1000

Energy Technology Data Exchange (ETDEWEB)

Poursalehi, Navid; Nejati-Zadeh, Mostafa; Minuchehr, Abdolhamid [Dept. of Nuclear Engineering, Shahid Beheshti University, Tehran (Iran, Islamic Republic of)

2017-02-15

Increasing the operation cycle length can be an important goal in the fuel reload design of a nuclear reactor core. In this research paper, a new optimization approach, electromagnetism mechanism (EM), is applied to the fuel arrangement design of the Bushehr WWER-1000 core. For this purpose, a neutronic solver has been developed for calculating the required parameters during the reload cycle of the reactor. In this package, two modules have been linked, including PARCS v2.7 and WIMS-5B codes, integrated in a solver for using in the fuel arrangement optimization operation. The first results of the prepared package, along with the cycle for the original pattern of Bushehr WWER-1000, are compared and verified according to the Final Safety Analysis Report and then the results of exploited EM linked with Purdue Advanced Reactor Core Simulator (PARCS) and Winfrith Improved Multigroup Scheme (WIMS) codes are reported for the loading pattern optimization. Totally, the numerical results of our loading pattern optimization indicate the power of the EM for this problem and also show the effective improvement of desired parameters for the gained semi-optimized core pattern in comparison to the designer scheme.

Analysis of coolant flow in central tube of WWER-440 fuel assemblies

International Nuclear Information System (INIS)

Zsiros, G.; Toth, S.; Attila Aszodi, A.

2011-01-01

Three dimensional computational fluid dynamics model has been built to investigate the coolant flow in the central tube of the WWER-440 fuel assemblies. The model was verified based on measured data of the Kurchatov Institute. With the model calculations were performed for two fuel assemblies used in PAKS NPP. One of them has symmetrical and another has inclined pin power profile. Ratios of the outlet mass fluxes of the central tube to the inlet mass fluxes of the rod bundle were determined. Heat up ratios of the tube and rod bundle flows were calculated too. Sensitivity of the results on the assembly power distribution, inlet temperature and mass flow rate was investigated. The results of these simulations can be used as boundary conditions of central tube in studies of coolant mixing in fuel assembly heads. (Authors)

Application of the LBB regulatory approach to the steamlines of advanced WWER 1000 reactor

Energy Technology Data Exchange (ETDEWEB)

Kiselyov, V.A.; Sokov, L.M.

1997-04-01

The LBB regulatory approach adopted in Russia in 1993 as an extra safety barrier is described for advanced WWER 1000 reactor steamline. The application of LBB concept requires the following additional protections. First, the steamline should be a highly qualified piping, performed in accordance with the applicable regulations and guidelines, carefully screened to verify that it is not subjected to any disqualifying failure mechanism. Second, a deterministic fracture mechanics analysis and leak rate evaluation have been performed to demonstrate that postulated through-wall crack that yields 95 1/min at normal operation conditions is stable even under seismic loads. Finally, it has been verified that the leak detection systems are sufficiently reliable, diverse and sensitive, and that adequate margins exist to detect a through wall crack smaller than the critical size. The obtained results are encouraging and show the possibility of the application of the LBB case to the steamline of advanced WWER 1000 reactor.

Application of the LBB regulatory approach to the steamlines of advanced WWER 1000 reactor

International Nuclear Information System (INIS)

Kiselyov, V.A.; Sokov, L.M.

1997-01-01

The LBB regulatory approach adopted in Russia in 1993 as an extra safety barrier is described for advanced WWER 1000 reactor steamline. The application of LBB concept requires the following additional protections. First, the steamline should be a highly qualified piping, performed in accordance with the applicable regulations and guidelines, carefully screened to verify that it is not subjected to any disqualifying failure mechanism. Second, a deterministic fracture mechanics analysis and leak rate evaluation have been performed to demonstrate that postulated through-wall crack that yields 95 1/min at normal operation conditions is stable even under seismic loads. Finally, it has been verified that the leak detection systems are sufficiently reliable, diverse and sensitive, and that adequate margins exist to detect a through wall crack smaller than the critical size. The obtained results are encouraging and show the possibility of the application of the LBB case to the steamline of advanced WWER 1000 reactor

Performance of the Westinghouse WWER-1000 fuel design

International Nuclear Information System (INIS)

Höglund, J.; Jansson, A.; Latorre, R.; Davis, D.

2015-01-01

In 2005, six (6) Westinghouse WWER-1000 Lead Test Assemblies (LTAs) were loaded in South Ukraine Unit 3 (SU3). The LTAs completed the planned four cycles of operation and reached an average assembly burnup in excess of 43 MWd/ kgU. Post Irradiation Examination (PIE) inspections were performed after completion of each cycle and it was concluded that the 6 Westinghouse LTAs performed as expected during their operational regimes. In 2010, a full region of 42 assemblies of an enhanced WWER-1000 fuel design for Ukrainian reactors, designated WFA, was loaded in SU3. The WFA includes features that further mitigate assembly bow while at the same time improving the fuel cycle economy. In 2015, 26 WFAs completed their planned four cycles of operation reaching an average assembly burnup in excess of 42 MWd/ kgU. Currently 36 WFAs continue operating their fourth cycle in SU3. In addition, South Ukraine Unit 2 (SU2) has been loaded with WFAs and 27 assemblies have completed two cycles of operation reaching an average assembly burnup above 24 MWd/kgU. PIE for the WFAs has been completed after each cycle of operation. All assemblies have been examined for visible damage or non-standard position of fuel assembly components during unloading and reloading. All WFAs have also been subject to the standard leak testing process, with all fuel rods found to be hermetically sealed and non-leaking. Each outage, six WFAs have been subject to a more extensive inspection program. In 2012, 2013, and 2015, the Westinghouse Fuel Inspection and Repair Equipment (FIRE) workstation were used for the SU3 inspections. Excellent irradiation fuel performance has been observed and measured on all WFAs. The fuel assembly growth, rod cluster control assembly (RCCA) drag forces, oxide thickness, total fuel rod-to-nozzle gap channel closure, and fuel assembly bow data were within the bounds of the Westinghouse experience database. Results and concluding remarks from the PIEs are provided in this paper. In

Analysis of an accident with the main circulation tube rupture at the WWER-1000

International Nuclear Information System (INIS)

Boyadzhiev, A.I.; Stefanova, S.J.

1984-01-01

In connection with the forthcoming construction of a npp with the wwer-1000 reactor the loss of coolant accident associated with the main circulation tube rupture at the inlet near the reactor is analyzed. The relap4/mod6 program is used for the analysis. The data obtained show that the coolant outflow stage continues for about 25s. On the average the pressure in the circuits varies from 16 to 10 mpa per 0.1s and then it continues to decrease slowly. The pressure in the steam generator at the secondary circuits end increases approximately up to 6.9 MPa as a result of steam generator blocking and remaining coolant heating and then somewhat decreases owing to the primary circuit cooling. By the end of the fuel and can temperatures are equalized and the heat transfer coefficient is stabilized at the level of 100 w/1 (m 2 xK). It is concluded that during a loss of coolant accident at the wwer-1000 reactor in procesess of coolant blowdown in the medium power fuel elemets neither the fuel, melting temperature (3000 k), nor the critical temperature (1000 k) of plastic deformation zirconiu can initiation are attained

Methodology for qualification of in-service inspection systems for WWER nuclear power plants. A publication of the extrabudgetary programme on the safety of WWER and RBMK nuclear power plants

International Nuclear Information System (INIS)

1998-03-01

Program was initiated by IAEA in 1990 with the aim to assist the countries of Central and Eastern Europe and former Soviet Union in evaluating the safety of their first generation WWER-440/230 nuclear power plants. The main objectives were: to identify major design and operational safety issues; to establish international consensus on priorities for safety improvements; and to provide assistance in the review of the competence and and adequacy of safety improvement programs. The scope was extended in 1992 to include RBMK, WWER-440/312 and WWER-1000 plants in operation and under construction. Integrity of primary circuit is fundamental for the safe operation of any nuclear power plant. In-service inspection (ISI) in general terms and in particular, non-destructive tests (NDT) play a key role in maintaining primary circuit integrity. This report provides a methodology for qualification of ISI systems which might be used by WWER operating countries as a commonly accepted basis for further development of the necessary qualification related infrastructures. It also provides several qualification principles defining the administrative framework needed for the practical implementation of the methodology, a description of the process of qualification of an inspection system, specifying its minimum technical and documentation related requirements, as well as specific requirements with regard to the NDT procedures, equipment and personnel to be qualified and the test specimen to be used in practical trials. Finally, the report suggests an appropriate distribution of responsibilities among all the parties involved in a qualification process, based on international practice

Part-task simulator of a WWER-440 type nuclear power plant unit

International Nuclear Information System (INIS)

Palecek, P.

1990-01-01

In the present paper the design of a part-task simulator for WWER-440 type nuclear power plant units by the CEZ (Czech Power Works) Concern is reported. This part-task simulator has been designed for the training of NPP operating personnel. It includes a central computer that is coupled with the training work places and the trainer place. Interchange of information is performed by functional keyboards and semigraphical colour displays. The process is simulated, also in real time scale, on the basis of dynamic models. In addition to the precision of the models used, great importance has primarily been attached to plasticity of information presentation. The part-task simulator may be applied to simulation and demonstration as well as to teaching purposes. The paper presents the achieved state of implementation of the part-task simulator and points out some further stage of evolution. (author)

Report of a consultants meeting on control rod insertion reliability for WWER-1000 nuclear power plants. Extrabudgetary programme on the safety of WWER and RBMK nuclear power plants

International Nuclear Information System (INIS)

1995-09-01

Starting from 1992, an increased drop time of control rods exceeding the design limit of four seconds has been observed in most of the operating WWER-1000 reactors in Russia and in the Ukraine. In some cases a dropped control rod became stuck in an intermediate position near the bottom of the core. In October 1994, a similar control rod problem was also observed at Unit 6 of the Kozloduy NPP. The issue of control rod insertion reliability was considered at a consultants' meeting on ''Core Control and Protection Strategy of WWER-1000 Reactors'' in April 1994. A consultants' meeting specifically focused on ''Control Rod Insertion Reliability'' was convened in Vienna in February 1995 attended by 15 international experts. The objectives of this meeting were: The exchange of international experience on problems and solutions related to anomalous control rod insertion; judgement of the safety concern of this issue for WWER-1000 reactors based on safety analyses; consideration of regulatory requirements and interim measures to continue operation in short term including modifications implemented or planned; and, status of root cause analyses and pending problems. The technical discussions were held in plenary sessions and in three working groups devoted to specific aspects of the issue. Refs, figs, tabs

Results of trial operation of the WWER advanced fuel assemblies

International Nuclear Information System (INIS)

Vasilchenko, I.; Dragunov, Y.; Mikhalchuk, A.

2001-01-01

The paper describes results from experimental operation of advanced WWER-1000 fuel assemblies (AFA) at five units in Balakovo NPP. Advanced fuel is developed according to the concept of standard WWER-1000 fuel assembly (jacket-free). The new features includes: 1) zirconium guiding channels (alloy E-635 and E-110) and spacer grids (alloy E-110); 2) integrated burnable absorber gadolinium; 3) extended service life of fuel assemblies (FA) and absorber rods (possibility of repair of FA); 4) improved adoption to reactor conditions. Some results of AFA pilot operation of a three year operation are presented and analyses of effectiveness of improvements are made concerning application of zirconium channels and grids; application of integrated burnable absorbers; extension of FA and absorbing rods service life and FA repairability. These new features of WWER-1000 fuel design allow: 1) to reduce the average fuel enrichment to the 3.77% instead of 4.31% in U-235; 2) to reduce the FA axial load in reactor hot state by 40%,; 3) increasing of fuel operation in reactor to the 30000 effective days with possibility to have a 5-year residence time in the reactor. The design of new generation FA for WWER-440 reactors involves few key changes. Fuel inventory in new fuel design is increased due to elongation of fuel stack and reducing the diameter of the central hole. Vibration stability is enhanced as a result of: no-play junction of the fuel rod with the lower grid; change of SG arrangements; strengthening of the lower grid unit; secure of the central tube in the gap. Water-uranium ration is increased. Introduction of all these kinds of modernization in a 5-year fuel cycle reduces fuel component in the energy cost to the 7%

Alternative technology of containment construction for WWER 1000 nuclear power plant

International Nuclear Information System (INIS)

Chalus, Z.

1982-01-01

A number of alternatives was assessed for the assembly of the steel elements of the cylindrical part of containment. Alternative 1 is based on the common technology of manufacture, transport and assembly of reinforced concrete blocks of ca. 3x12 m in size, used for building leak-proof walls of WWER 440 nuclear power plants. Alternative 2 is based on reinforced concrete blocks using 12x12 m blocks assembled from individual elements on the building. site. Alternative 3 is a specific variant of the previous alternative. Alternative 4 envisages the assembly of a prefabricated support structure made of steel. Alternative 5 is based on the gradual assembly of partial elements mounted onto a support structure. Alternative 6 only differs from 5 in the method of assembly and manufacture of the support structure. All alternatives are shown in diagrams. (J.B.)

Fuel rod behaviour at high burnup WWER fuel cycles

International Nuclear Information System (INIS)

Medvedev, A.; Bogatyr, S.; Kouznetsov, V.; Khvostov, G.; Lagovsky; Korystin, L.; Poudov, V.

2003-01-01

The modernisation of WWER fuel cycles is carried out on the base of complete modelling and experimental justification of fuel rods up to 70 MWd/kgU. The modelling justification of the reliability of fuel rod and fuel rod with gadolinium is carried out with the use of certified START-3 code. START-3 code has a continuous experimental support. The thermophysical and strength reliability of WWER-440 fuel is justified for fuel rod and pellet burnups 65 MWd/kgU and 74 MWd/U, accordingly. Results of analysis are demonstrated by the example of uranium-gadolinium fuel assemblies of second generation under 5-year cycle with a portion of 6-year assemblies and by the example of successfully completed pilot operation of 5-year cycle fuel assemblies during 6 years at unit 3 of Kolskaja NPP. The thermophysical and strength reliability of WWER-1000 fuel is justified for a fuel rod burnup 66 MWd/kgU by the example of fuel operation under 4-year cycles and 6-year test operation of fuel assemblies at unit 1 of Kalininskaya NPP. By the example of 5-year cycle at Dukovany NPP Unit 2 it was demonstrated that WWER fuel rod of a burnup 58 MWd/kgU ensure reliable operation under load following conditions. The analysis has confirmed sufficient reserves of Russian fuel to implement program of JSC 'TVEL' in order to improve technical and economical parameters of WWER fuel cycles

Application of modified version of SPPS-1 - HEXAB-2DB computer code package for operational analyses of fuel behaviour in WWER-440 reactors at Kozloduy NPP

Energy Technology Data Exchange (ETDEWEB)

Kharalampieva, Ts; Stoyanova, I; Antonov, A; Simeonov, T [Kombinat Atomna Energetika, Kozloduj (Bulgaria); Petkov, P [Bylgarska Akademiya na Naukite, Sofia (Bulgaria). Inst. za Yadrena Izsledvaniya i Yadrena Energetika

1994-12-31

The modified version of SPPS-1 code called SPPS-1-HEXAB-2DB was applied for the purposes of the operational analysis and power peaking factors and reactor core critical parameters predictions of WWER-440s. The results of the calculations performed by the use of SPPS-1-HEXAB-2DB code and the corresponding parameters obtained from experiments at Kozloduy NPP WWER-440s as well as the results of fuel rod power distribution are presented. The method of operation simulation of reactor core with 349 assemblies (Unit 4) and with 313 fuel assemblies and 36 dummy fuel assemblies (Unit 1) is outlined. The modified code calculates not only fuel burnup and Pm-149 and Sm-149 concentrations distributions but also the space distribution of I-135 and Xe-135 concentrations. In this way it makes possible to perform the reactor operation simulation during the immediate periods after the reactor start-up or shut-down and to predict the critical reactor core parameters during transients. The results obtained show that SPPS-1-HEXAB-2DB code describes adequately the reactor core status. The new SPPS-1 code algorithm for estimation of assembly-wise power peaking factors distribution in reactor core is also described. The new code provides an option for checking the correctness of reactor core symmetry. The experience from the use of the modified SPPS-1-HEXAB-2DB code system confirms the provision of improved availability of operational analysis, prediction of Kozloduy NPP WWER-440s safe operations and fuel behaviour estimation. 14 tabs., 4 figs., 5 refs.

Methodology for the evaluation of tolerability of defects in WWER-1000/V-320 reactor pressure vessels

International Nuclear Information System (INIS)

Brumovsky, M.; Horacek, L.; Ruscak, M.

1996-05-01

The methodology provides guidelines for the assessment of tolerability of defects found during in-service inspection of the base material and overlay of WWER-1000/V-320 type reactor pressure vessels. With regard to the method of calculating the tolerability of defects and rules for the preparation and implementation of repairs, this methodology can also find use in the assessment of tolerability of defects in selected facilities of WWER-1000/V-320 type nuclear power plants provided that adequate input data concerning the materials, manufacturing technology, and operating load regime are available and that the facilities are made of ferrite/bainite type steels. This methodology should serve as a binding document underlying the development of a technical approach to provisions for a further operation of facilities in which intolerable defects have been found by nondestructive testing. (author)

Code systems for effective and precise calculation of the basic neutron characteristics, core loading optimization, analysis and estimation of the operation regimes of WWER type reactors

International Nuclear Information System (INIS)

Apostolov, T.; Ivanov, K.; Prodanova, R.; Manolova, M.; Petrova, T.; Alekova, G.

1993-01-01

Two directions for investigations are suggested: 1) Analysis and evaluation of the real loading patterns and operational regimes for Kozloduy NPP WWER-440 and WWER-1000 in the frame of the recent safety criteria and nuclear power plant operating limits. 2) Development of modern code system for WWER type reactor core analysis with advanced features: new design and materials for fuel and control rods, increasing the fuel enrichment, using the integral and discrete burnable absorbers etc. The fuel technology design evolution maximizes the fuel utilization efficiency, improves operation performance and enhances safety margins. By the joint efforts of specialists from INRNE, Sofia (BG) and KAB, Berlin (GE), the codes NESSEL-IV-EC, PYTHIA and DERAB have been developed and verified. In the frame of the PHARE programme the joint project ASPERCA has been proposed intended for reactor physics calculations with PHYBER-WWER code for safety enhancement and operation reliability improvement. In-core fuel management benchmarks for 4 cycles of unit 2 (WWER-440) and 2 cycles of unit 5 (WWER-1000) have been performed. The coordination of burnable absorber design implementation, low leakage loadings usage, reloading enrichment increase and steel content reduction in the core have made the reactor core analysis more demanding and the definition of loading patterns - more difficult. This complexity requires routine use of three-dimensional fast accurate core model with extended and updated cross section libraries. To meet the needs of WWER advanced loading patterns and in-core fuel management improvements the HEXANES code systems is being developed and qualified. Some test calculations have been carried out by the HEXANES code system investigating the influence of Gd in the fuel on the main reactor physics parameters. For reevaluation of the core safety-related design limits forming the basis of licensing procedure, the code DYN3D/M2 is used. 16 refs., 3 figs. (author)

Designing a nuclear power plant with 1000 MW WWER-type units

Energy Technology Data Exchange (ETDEWEB)

Berkovich, V; Kaloshin, J; Tatarnikov, V; Shenderovich, A

1977-06-01

A brief description is presented of a WWER-1000 nuclear power plant also considering its environmental impact and the problem of core poisoning. The following indicators are graphically shown in relation to the reactor output: turbogenerator unit outputs, efficiency, specific capital costs and own costs of electric power generated by the Voronezh nuclear power plant. Also listed are the specific consumption of metal and concrete, specific equipment weight and the specific volume of the buildings of the main generating unit as well as the cross section thereof.

Procedure for validating the life extension for the WWER-440 internals at NV NPP unit 3

International Nuclear Information System (INIS)

Filatov, V.M.; Evropin, S.V.

2001-01-01

The design lifetime (30 years) of the 1st generation WWER-440 reactor facilities is nearing completion in Russia. One of the major problems is to validate the life extension (LE) of the reactor internals ensuring the core arrangement and free passage of the control and protection system components during different operating modes, emergency modes included. The internals at the 1st generation units are designed so that to enable their replacement. But it requires a lot of funds and time. The work has been done to demonstrate that the internals may be further safely operated without their components being replaced provided their strength, longevity and serviceability are sufficiently validated. (author)

Improving the ALUeS diagnostic system for determining the coolant leak place from the WWER-440 primary circuit

International Nuclear Information System (INIS)

Markosyan, G.R.; Petrosyan, V.G.; Shakhverdyan, S.V.; Aslanyan, M.A.

2000-01-01

The new algorithm for localizing the leakage from the WWER-440 primary circuit, intended for operation in the Siemens ALUeS system, is proposed. The results of the algorithm realization in the leakage control system (the ALUeS system copy), installed at the Armenian NPP power unit-2, are presented. The leakage localization algorithm proposed was tested in other experiments. The leakage position in the majority of cases is determined exactly. Small (up to 5 m) deviations, the cause whereof were incorrect readings of the transducers, were observed [ru

Technically feasibility solution for WWER-440/B230. Confinement upgrading

International Nuclear Information System (INIS)

Balabanov, E.; Sartmandgiev, A.

2000-01-01

A concept for modernization of the units 1 to 4 of Kozloduy NPP ( WWER-440/V230) localization system to cope with a large spectrum of accidents, including 2x100% LOCA is proposed. This concept in foreseeing the installation of several systems, which altogether would form a complex of beyond original design basis accidents mitigation systems. These systems are: Pressure Suppression System (PSS) - with implementation of VNIIAES vortex condenser - supposed to cope with the first pressure peak and to protect the confinement integrity, hydrogen control system-with implementation of Passive Autocatalic Recombiners (PAR) - supposed to cope with hydrogen and to mitigate the possible uncontrolled release of radiation products, active Filter Venting System (FVS) - to maintain underpressure in the confinement and to retain radioactive products, as well as to control radioactive releases during a long period of time. This concept is ensuring: integrity of the localization system for the full spectrum of primary LOCA, non violation of the dose limits, defined by BNSA, for a large spectrum of accidents including severe accidents, fulfillment of IAEA recommendation (INSAG - 3) - decrease the probability for large radioactive release by a factor of 10 outside of NPP side

Results of experimental investigations for substantiation of WWER cermet fuel pin performance

International Nuclear Information System (INIS)

Popov, V.V.; Karpin, A.D.; Isupov, I.A.; Rumyantsev, V.N.; Troyanov, V.M.; Subonyaev, V.N.; Melnichenko, N.A.

1997-01-01

The out-of-pile experiment results on interaction of the cladding and matrix materials and uranium dioxide at cermet fuel temperature for normal operating conditions of the WWER-440 reactor are analyzed. Cermet fuel element behaviour under the maximum designed damage of the WWER-440 reactor is considered. In the AM reactor loop a fission product output from the unsealed cermet fuel elements have been studied. (author). 6 figs, 3 tabs

Fuel element cladding state change mathematical model for a WWER-1000 plant operated in the mode of varying loading

Directory of Open Access Journals (Sweden)

S. N. Pelykh

2010-09-01

Full Text Available Main features of a fuel element cladding state change mathematical model for a WWER-1000 reactor plant operated in the mode of varying loading are listed. The integrated model is based on the energy creep theory, uses the finite element method for imultaneous solution of the fuel element heat conduction and mechanical deformation equa-tions. Proposed mathematical model allows us to determine the influence of the WWER-1000 regime parameters and fuel assembly design characteristics on the change of cladding properties under different loading conditions of normal operation, as well as the cladding limiting state at variable loading depending on the length, depth and number of cycles.

SCK-CEN Contribution to the IAEA Round Robin Exercise on WWER-440 RPV Weld Metal Irradiation Embrittlement, annealing and Re-Embrittlement. Second Progress Report

International Nuclear Information System (INIS)

Van Walle, E.; Chaouadi, R.; Scibetta, M.; Lucon, E.; Weber, M.

1999-07-01

The report gives the actual status of the contribution of the Belgian Nuclear Research Centre SCK-CEN to the IAEA Round Robin Exercise on WWER-440 RPV Weld Material Irradiation, Annealing and Re-Embrittlement. Results from the reference testing of unirradiated material as well as the results of the CHIVAS-7 experiment are discussed

Assessment of spent WWER-440 fuel performance under long-term storage conditions

Energy Technology Data Exchange (ETDEWEB)

Kupca, L [VUJE Inc. (Slovakia)

2012-07-01

In the Slovak Republic are under operation 6 units (4 in the Jaslovske Bohunice site, and 2 in the Mochovce), 2 units are under construction in Mochovce site. All units are WWER-440 type. The fresh fuel is imported from the Russian Federation. The spent fuel assemblies are stored in wet conditions in Bohunice Interim Storage Spent Fuel Facility (SFIS). By 15 July 2008, there were 8413 assemblies in SFIS. The objectives are: 1) Wet AR storage of spent fuel from the NPP Bohunice and Mochovce: Surveillance of conditions for spent fuel storage in the at-reactor (AR) storage pools of both NPP's (characteristics of pool water, corrosion product data); Visual control of storage pool components; Evaluation of storage conditions with respect to long-term stability (corrosion of fuel cladding, structural materials); 2) Wet SFIS storage at Bohunice: Measurement of spent fuel conditions during the long-term wet storage, activity data in the storage casks and amount of crud; Surveillance program for SFIS structural materials.

Effect of high-temperature filtration on impurity composition in the primary circuit coolant of power units with WWER-1000 reactors

International Nuclear Information System (INIS)

Efimov, A.A.; Moskvin, L.N.; Gusev, B.A.; Leont'ev, G.G.; Nekrest'yanov, S.N.

1992-01-01

The effects of high-temperature filtration on changes in dispersive, chemical, radioisotope and phase compositions of impurities in primary circuit coolant of NPP with the WWER-1000 reactor are studied. Special filters are used for the studies. The data obtained confirm the applicability of high-temperature filtration for purification of WWER reactor water and steam separators at NPPs with RBMK reactors

Seismic assessment of Kozloduy WWER-440, model 230 nuclear power plant

International Nuclear Information System (INIS)

Monette, P.; Baltus, R.; Yanev, P.; Campbell, R.

1993-01-01

A preliminary report is given of the findings of an IAEA sponsored walkdown of the WWER-440, model 230 at Kozloduy, in May 1991. The scope of the IAEA mission was to determine the lower bound seismic capacity of the plant and to make recommendations for improvements to increase the earthquake resistance. The methodology utilized in the assessment is that used for evaluation of the seismic margin in U.S. nuclear power plants subjected to earthquakes beyond their design basis. Included in the assessment is the establishment of a safe shutdown path which would include the capacity to mitigate a small break in the primary system, performance of a walkdown of the safe shutdown path and calculation of the high-confidence-of-low-probability-of-failure (HCLPF) of the safe shutdown path. Excluding system design deficiency relative to U.S. and Western Europe standards, it was found that the plant has many seismic vulnerabilities similar to those that existed in many of the U.S. plants prior to about 1979 when the Systematic Evaluation Program was initiated. (Z.S.) 1 tab., 1 fig

Best estimate modeling of fuel thermomechanical behaviour in WWER 1000 LB LOCA

International Nuclear Information System (INIS)

Valach, M.; Klouzal, J.; Zymak, J.; Dostal, M.

2009-01-01

The paper summarizes our calculations of the performance of the WWER 1000 NPP fuel rods during postulated LB LOCA. The thermomechanical modeling was performed by FRAPTRAN using the FRACAS-I mechanical model using the boundary conditions calculated by the ATHLET code. The results and their statistical evaluation are presented, the process of the generalization of gained insight into the best-estimate thermal-hydraulic analyses (BE TM) predictions in order to define a generic BE TM methodology is outlined (authors)

Designing a nuclear power plant with 1000 MW WWER-type units

International Nuclear Information System (INIS)

Berkovich, V.; Kaloshin, J.; Tatarnikov, V.; Shenderovich, A.

1977-01-01

A brief description is presented of a WWER-1000 nuclear power plant also considering its environmental impact and the problem of core poisoning. The following indicators are graphically shown in relation to the reactor output: turbogenerator unit outputs, efficiency, specific capital costs and own costs of electric power generated by the Voronezh nuclear power plant. Also listed are the specific consumption of metal and concrete, specific equipment weight and the specific volume of the buildings of the main generating unit as well as the cross section thereof. (J.B.)

Technological problems connected with execution of the protection sheets for nuclear power sets WWER-1000

International Nuclear Information System (INIS)

Hajutin, J.G.; Kriczewskij, A.Z.

1977-01-01

The choice of the structure and the prestressing system of the R.C. protection sheet for nuclear power sets WWER-1000 is motivated. The technological problems arised during the execution stage, as well as the technological line producing the tendons to prestress the structure by up winding are presented. (author)

Fuel pin bowing and related investigation of the gadolinium fuel pin influence on power release inside of neighbouring fuel pins in a WWER-440 type core

International Nuclear Information System (INIS)

Mikus, J.

2006-01-01

As known both the WWER-440 and WWER-1000 reactors are systematically modernized to enhance their safety and economical parameters of operation. For this purpose new fuel assemblies (FAs) were designed with improved technical parameters, e.g., containing fuel pins (FPs) in which Gd 2 O 3 burnable absorber is integrated into fuel. Presence of such FPs in reactor core results in a strong depression of thermal neutrons in their positions and corresponding high gradients in neighbouring FPs. Consequently, similar situation in neighbouring FPs can be expected as for both the power release and temperature gradients. The purpose of this work consists in investigation of the gadolinium FP influence on space power distribution, especially from viewpoint of the values and gradient occurrence inside of the neighbouring FPs that could result in static loads with some consequences, e.g., a contribution to FP/FA bowing. Since detailed power distributions cannot be obtained in the NPPs, needed information is provided by means of experiments on research reactors. As for the power release measurement inside of FPs, some special (e.g. track) detectors placed between fuel pellets are usually used. Since such works are relatively complicated and time consuming, an evaluation method based on mathematical modelling and numerical approximation was proposed by means of that, and using measured (integral) power release in selected FPs, needed power release values inside of investigated FPs, can be estimated. For this purpose, experimental results from light water, zero-power research reactor LR-0 obtained by measurements in a WWER-440 type core with 19 FAs at zero boron concentration and containing some FPs with gadolinium (Gd FPs) were utilized. Application of the proposed evaluation method is demonstrated on investigated FPs neighbouring a Gd FP by means of the: relative azimuthal power distribution estimation inside of investigated FPs on their fuel pellet surface in horizontal plane

Ammonia role in WWER primary circuit water chemistry optimization

International Nuclear Information System (INIS)

Kritskij, V.G.; Stjagkin, P.S.; Chvedova, M.N.; Slobodov, A.A.

1999-01-01

Ammonia influence on iron crud's solubility at 300 deg. C and different relations of boric acid and alkaline cation sum are considered. Reduction of dose rate on WWER-440 steam generators at average ammonia concentration increasing is empirically explained. Practical recommendations on optimization of WWER primary circuit water chemistry are given. (author)

Control rod drive WWER 1000 – tuning of input parameters

Directory of Open Access Journals (Sweden)

Markov P.

2007-10-01

Full Text Available The article picks up on the contributions presented at the conferences Computational Mechanics 2005 and 2006, in which a calculational model of an upgraded control rod linear stepping drive for the reactors WWER 1000 (LKP-M/3 was described and results of analysis of dynamical response of its individual parts when moving up- and downwards were included. The contribution deals with the tuning of input parameters of the 3rd generation drive with the objective of reaching its running as smooth as possible so as to get a minimum wear of its parts as a result and hence to achieve maximum life-time.

Experimental study of the passive flooding system in the WWER-1000 reactor

International Nuclear Information System (INIS)

Malyshev, A.B.; Efanov, A.D.; Kalyakin, S.G.

2002-01-01

The design solution of the passive flooding system in the WWER-1000 reactor core with the V-392 reactor facility and the scheme of the GE-2 large-scale thermohydraulic stand for substantiation of its functions are presented. The proposals, improving the efficiency of the system are developed on the basis of the experimental studies on the equipment input-output operational characteristics and the recommendations on the substantiation of the function of the reactor core flooding system are given [ru

HEXTRAN-SMABRE calculation of the 6th AER Benchmark, main steam line break in a WWER-440 NPP

International Nuclear Information System (INIS)

Haemaelaeinen, A.; Kyrki-Rajamaeki, R.

2003-01-01

The sixth AER benchmark is the second AER benchmark for couplings of the thermal hydraulic codes and three dimensional neutron kinetic core models. It concerns a double end break of one main steam line in a WWER-440 plant. The core is at the end of its first cycle in full power conditions. In VTT HEXTRAN2.9 is used for the core kinetics and dynamics and SMABRE4.8 as a thermal hydraulic model for the primary and secondary loop. The plant model for SMABRE consists mainly of two input models, Loviisa model and a standard WWER-440/213 plant model. The primary loop includes six separate loops, the pressure vessel is divided into six parallel channels in SMABRE and the whole core calculation is performed in the core with HEXTRAN. The horizontal steam generators are modelled with heat transfer tubes in five levels and vertically with two parts, riser and downcomer. With this kind of detailed modelling of steam generators there occurs strong flashing after break opening. As a sequence of the main steam line break at nominal power level, the reactor trip is followed quite soon. The liquid temperature continues to decrease in one core inlet sector which may lead to recriticality and neuron power increase. The situation is very sensitive to small changes in the steam generator and break flow modelling and therefore several sensitivity calculations have been done. Also two stucked control rods have been assumed. Due to boric acid concentration in the high pressure safety injection subcriticality is finally guaranteed in the transient (Authors)

Requirements and possible upgrading concept for the WWER-440/213: Mochovce NPP structures under seismic conditions

International Nuclear Information System (INIS)

Freiman, M.

1993-01-01

The Mochovce-Nuclear Power Plant is one of the WWER-440/213 plants which has been designed against earthquake. Nevertheless, the design earthquake has not been assessed adequately to the seismic hazard at the site. A new seismic design shall include an increased seismic input and assure an acceptable standard of safety. This contribution is related to some design aspects of civil structures for this nearly finished plant, such as: existing design and its margins with regard to the employed codes; requirements for a new design concept; effects to be expected by an increased design earthquake; applicable design methods; use of inelastic design spectra, behavior factors and capacity design; feasible upgrading measures. (author)

Upgrade the startup test instrumentation (ANMS) with innovated I and C system at the Dukovany WWER 440/213 units

International Nuclear Information System (INIS)

Kocek, V.

2005-01-01

The paper focuses on the innovation procedures of physics startup tests instrumentation used in Dukovany NPP (ANMS) connected with I and C system refurbishment of the Dukovany WWER 440/213 units. The following matters are further discussed in this paper: a) changes in ANMS design, whose has been carried out due to reflect the situation connected with I and C innovation; b) process of consistency checking during implementation stage; c) results of the physics startup tests with upgraded ANMS in 2005 (introduction of Gd2 fuel on Dukovany NPP) (Authors)

WWER-440/V-230 Confinement modernization to upgrade the critical safety function 'Containment integrity' in case of severe accident

International Nuclear Information System (INIS)

Sartmadjiev, A.

1999-01-01

In this lecture the WWER-440/V-230 confinement modernization to upgrade the critical safety function 'Containment integrity' in case of severe accident is presented. There are discussed: design limitations of the location system; consequence from these design limitations; a few confinement reconstruction concepts of this type of units worldwide; and purpose of the confinement reconstruction - to improve significantly the original design, ensuring (1) localization for all possible primary breaks and (2) limitation of the radiological consequences for the personnel, the population and the environment below the regulatory requirements

National report on nuclear power plant control and instrumentation in Czechoslovakia

International Nuclear Information System (INIS)

Stirsky, P.; Karpeta, C.

1986-01-01

Research, development and design efforts in the field of nuclear power plant I and C systems in Czechoslovakia have been recently aimed at solving the following problems: setting the parameters of the WWER 440 units control and protection systems and testing them in the power phase of commissioning; design and simulation of the WWER 440 units control system performance under the conditions of steam bleeding for a centralized heat supply system; development of a simulation model of the unit WWER 1000 dynamics for the purpose of I and C systems investigation and design; design of innovated I and C systems for WWER 440 and WWER 1000 units

Decommissioning costs of WWER-440 nuclear power plants. Interim report: Data collection and preliminary evaluations

International Nuclear Information System (INIS)

2002-11-01

Based on the interest in decommissioning costs within Member States, especially in WWER- 440 operating countries that face the complex decision about continued operation vs. decommissioning in the near future, the IAEA launched the task to prepare a technical document on decommissioning costs of WWER-440 nuclear power plants. The main objectives of this publication were to present the decommissioning costs of WWER-440 NPPs in a uniform manner, i.e. using the cost item and cost group system of the Interim Technical Document on Nuclear Decommissioning 'A Proposed Standardised List of Items for Costing Purposes' developed jointly by the EC, the IAEA and the OECD Nuclear Energy Agency (NEA), and providing, as such, a basis for understanding decommissioning costs differences. Member States operating WWER-440 NPPs or having such units under shutdown or even under decommissioning conditions have been requested to provide cost estimates and other input data in order to facilitate understanding of their cost figures. Both decommissioning options, i.e. immediate decommissioning and safe enclosure, have been considered. In the aforementioned joint Interim Technical Document, cost items related to activities that are carried out with a similar emphasis, whether or not tied to a similar time schedule for decommissioning, or that are based on overall activities that cannot be categorised in a specific time period, are grouped as follows: pre-decommissioning actions; facility shutdown activities; procurement of general equipment and material; dismantling activities; waste processing, storage and disposal; site security, surveillance and maintenance; site restoration, cleanup and landscaping; project management, engineering and site support; research and development; fuel and nuclear material; other costs. Before starting implementation of the study, agreement was obtained on general financial, technical and social boundary conditions that should be used in order to facilitate

Ensuring the operational safety of nuclear power plants with WWER reactors

International Nuclear Information System (INIS)

Shasharin, G.A.; Veretennikov, G.A.; Abagyan, A.A.; Lesnoj, S.A.

1984-01-01

At the start of 1983, 27 nuclear power producing units with reactor facilities of the WWER type were in operation in the Soviet Union and other countries. In 1982 the average load factor for nuclear power plants with WWER reactors was 73 per cent. There was not a single nuclear accident or even damage with any significant radiation consequences in the WWER reactors during the entire period of their operation. The most modern nuclear power plants with WWER-440 and WWER-1000 reactors meet all present-day international requirements. Safe operation of the plants is achieved by a variety of measures, the most important of which include: procedures for increasing the reliability of plant equipment and systems; ensuring exact compliance with plant operating instructions; ensuring reliable operation of plant safety systems; action directed towards maintaining the skills of plant personnel at a level adequate to ensure the taking of proper action during transient processes and accident situations. The paper discusses concrete steps for ensuring safe nuclear power plant operation along these lines. In particular, measures such as the following are described: the use of a system for collecting and processing information on equipment failures and defects; the development and introduction of methods of early defect diagnosis; the performance of complex testing of safety systems; the training of highly skilled personnel for nuclear power plants at educational combines and at teaching and training centres making use of simulators; arranging accident-prevention training and special instruction for personnel. (author)

Water chemistry in WWER reactors

International Nuclear Information System (INIS)

Yurmanov, V.A.; Mamet, V.A.; Shestakov, Yu.M.; Amosov, M.M.

1997-01-01

In this paper ''Water Chemistry in WWER Reactors'', are briefly described the 30 WWERs in Russian and the Ukraine, and are pointed out the essential differences between the 440s and 1000s. The primary coolant in the six loops of the former type operates at 270-290 deg. C, while the four loops of the latter type are at 290-320 deg. C. Performance of the fuel has been generally good with some fission product activities emanating from tramp uranium. Incidents causing unusually high fission product levels were overheating of the 16th fuel load at Kola NPP in 1990 by a reduced coolant flow, and fuel defects at Novovoronezh NPP resulting from deposits of carbon and corrosion products. Organic carbon, depositing from the coolant in regions of high turbulence (i.e. at the spacer grids), provokes corrosion product deposition. The source of the organic is not known. New chemistry guidelines have been implemented since 1992-93 for Russian and Ukrainian WWERs. These include higher pH T values (7.0-7.1 as opposed to 6.6-6.9) and tighter controls on oxygen and impurities. Lower dose rates in steam generator channels are reported. Significant reduction in operator doses are achieved by these methods coupled with a ''soft decontamination'' involving changing the KOH concentration and, hence, the pH T before shutdown. The benefits of hydrazine treatment for deoxygenating feedwater and coolant prior to start up, for injecting before shutdown and for general chemistry control on radiation fields are described. (author). 7 refs, 9 figs, 8 tabs

Water chemistry in WWER reactors

Energy Technology Data Exchange (ETDEWEB)

Yurmanov, V A; Mamet, V A; Shestakov, Yu M; Amosov, M M [All-Russian Scientific Research Inst. for Nuclear Power Plants Operation, Moscow (Russian Federation)

1997-02-01

In this paper ``Water Chemistry in WWER Reactors``, are briefly described the 30 WWERs in Russian and the Ukraine, and are pointed out the essential differences between the 440s and 1000s. The primary coolant in the six loops of the former type operates at 270-290 deg. C, while the four loops of the latter type are at 290-320 deg. C. Performance of the fuel has been generally good with some fission product activities emanating from tramp uranium. Incidents causing unusually high fission product levels were overheating of the 16th fuel load at Kola NPP in 1990 by a reduced coolant flow, and fuel defects at Novovoronezh NPP resulting from deposits of carbon and corrosion products. Organic carbon, depositing from the coolant in regions of high turbulence (i.e. at the spacer grids), provokes corrosion product deposition. The source of the organic is not known. New chemistry guidelines have been implemented since 1992-93 for Russian and Ukrainian WWERs. These include higher pH{sub T} values (7.0-7.1 as opposed to 6.6-6.9) and tighter controls on oxygen and impurities. Lower dose rates in steam generator channels are reported. Significant reduction in operator doses are achieved by these methods coupled with a ``soft decontamination`` involving changing the KOH concentration and, hence, the pH{sub T} before shutdown. The benefits of hydrazine treatment for deoxygenating feedwater and coolant prior to start up, for injecting before shutdown and for general chemistry control on radiation fields are described. (author). 7 refs, 9 figs, 8 tabs.

Operation results of 3-rd generation nuclear fuel WWER-440 in initial period

International Nuclear Information System (INIS)

Adeev, V.; Panov, A.

2011-01-01

On unit 4 of Kola NPP trial operation of 3-rd generation's fuel began in 2010. Fuel assemblies of 3-rd generation (FA-3) have a number of design features that provide better operational characteristics. Concise description of a design and the basic advantages of fuel of 3-rd generation are described in articles. Increasing of efficiency of nuclear fuel usage will be achieved by reduction of the parasitic capture of thermal neutrons in constructional materials (weight of zirconium is reduced), optimization of uranium-water relation (increase in fuel elements step), increasing of uranium loading (usage of fuel pellets with increased diameter and without central hole in them). By results of trial operation mass transition to use of given type of assemblies in WWER-440 is possible. This report presents the basic outcomes of the trial operation, a brief survey of the obtained data. The basic characteristics of the reactor core with fuel of 3-rd generation are resulted in work. (authors)

Study on the power control system for NPP power unit with the WWER-440 reactor

International Nuclear Information System (INIS)

Aleksandrova, N.D.; Naumov, A.V.

1981-01-01

Results of model investigations into basic version of the power control systems (PCS) conformably to the WWER-440 NPP power unit are stated. Transient processes in the power unit system when being two PCS versions during perturbations of different parameters: unit power, vapour pressure or position of control rods have been simulated. Investigations into the different PCS versions show that quality of operation of a traditional scheme with a turbine power controller and reactor pressure controller can be significantly improved with the introduction of a high-speed signal of pressure into the reactor controller. The PCS version with the compensation of interrelations between the turbine and reactor controllers constructed according to the same principles as the standard schemes of power units of thermal electric power plant is perspective as well [ru

Analyses of steam generator collector rupture for WWER-1000 using Relap5 code

Energy Technology Data Exchange (ETDEWEB)

Balabanov, E.; Ivanova, A. [Energoproekt, Sofia (Bulgaria)

1995-12-31

The paper presents some of the results of analyses of an accident with a LOCA from the primary to the secondary side of a WWER-1000/320 unit. The objective of the analyses is to estimate the primary coolant to the atmosphere, to point out the necessity of a well defined operator strategy for this type of accident as well as to evaluate the possibility to diagnose the accident and to minimize the radiological impact on the environment.

Analyses of steam generator collector rupture for WWER-1000 using Relap5 code

International Nuclear Information System (INIS)

Balabanov, E.; Ivanova, A.

1995-01-01

The paper presents some of the results of analyses of an accident with a LOCA from the primary to the secondary side of a WWER-1000/320 unit. The objective of the analyses is to estimate the primary coolant to the atmosphere, to point out the necessity of a well defined operator strategy for this type of accident as well as to evaluate the possibility to diagnose the accident and to minimize the radiological impact on the environment

Analyses of steam generator collector rupture for WWER-1000 using Relap5 code

Energy Technology Data Exchange (ETDEWEB)

Balabanov, E; Ivanova, A [Energoproekt, Sofia (Bulgaria)

1996-12-31

The paper presents some of the results of analyses of an accident with a LOCA from the primary to the secondary side of a WWER-1000/320 unit. The objective of the analyses is to estimate the primary coolant to the atmosphere, to point out the necessity of a well defined operator strategy for this type of accident as well as to evaluate the possibility to diagnose the accident and to minimize the radiological impact on the environment.

Experimental support of WWER-440 fuel reliability and serviceability at high burnup

Energy Technology Data Exchange (ETDEWEB)

Smirnov, A; Ivanov, V; Pnyushkin, A [Nauchno-Issledovatel` skij Inst. Atomnykh Reaktorov, Dimitrovgrad (Russian Federation); Tzibulya, V [AO Mashinostroitelnij Zavod Electrostal (Russian Federation); Kolosovsky, V; Bibilashvili, Yu [Vsesoyuznyj Nauchno-Issledovatel` skij Inst. Neorganicheskikh Materialov, Moscow (Russian Federation); Dubrovin, K [Russian Research Centre Kurchatov Inst., Moscow (Russian Federation)

1994-12-31

Results from post-reactor examination of two WWER-440 fuel assemblies spent at the Kola NPP Unit 3 during 4 and 5 fuel cycles are presented. The fuel assembly states and their serviceability allowance are estimated experimentally at the RIAR hot laboratory and studied by non-destructive and destructive methods. The following parameters are examined: fuel assembly overall dimensions change; fuel element diameter change; fuel element cladding corrosion and hydriding; fuel element cladding mechanical properties; fission gas release from fuel and gas pressure; fuel macro- and microstructure. it has been found that the maximum fuel burnup of fuel assemblies No. 1 and No.2 achieved is 58.3 and 64.0 MWd/kg, respectively. The mechanical fuel pellets-cladding interaction has been observed at the average fuel burnup above 45 MWd/kg that occurred with increasing the local cladding diameter at the areas of pellets end arrangement (bamboo stick). The gas release linearly increases at the range 2.7% per 10 MWd/kg within burnup of 43-60 MWd/kg. 9 figs., 3 refs.

WWER-1000 reactor simulator. Workshop material

International Nuclear Information System (INIS)

2003-01-01

The International Atomic Energy Agency (IAEA) has established an activity in nuclear reactor simulation computer programs to assist its Member States in education. The objective is to provide, for a variety of advanced reactor types, insight and practice in their operational characteristics and their response to perturbations and accident situations. To achieve this, the IAEA arranges for the development and distribution of simulation programs and educational material and sponsors courses and workshops. The workshops are in two parts: techniques and tools for reactor simulator development; and the use of reactor simulators in education. Workshop material for the first part is covered in the IAEA publication: Training Course Series 12, 'Reactor Simulator Development' (2001). Course material for workshops using a pressurized water reactor (PWR) Simulator developed for the IAEA by Cassiopeia Technologies Inc. of Canada is presented in the IAEA publication: Training Course Series No. 22 'Pressurized Water Reactor Simulator' (2003) and Training Course Series No. 23 'Boiling Water Reactor Simulator' (2003). This report consists of course material for workshops using the WWER-1000 Reactor Department Simulator from the Moscow Engineering and Physics Institute, Russian Federation. N. V. Tikhonov and S. B. Vygovsky of the Moscow Engineering and Physics Institute prepared this report for the IAEA

The procedure for determination of special margin factors to account for a bow of the WWER-1000 fuel assemblies

International Nuclear Information System (INIS)

Tsyganov, S. V.; Marin, S. V.; Shishkov, L. K.

2008-01-01

Starting from 1980s, the problem of bow of the WWER-1000 reactor fuel assemblies and the effect of that on the operational safety is being discussed. At the initial period of time, the extension of time for dropping control rods of the control and protection system associated with this bow posed the highest threat. Later on, new more rigid structures were developed for fuel assemblies that eliminated the problems of control rods. However, bow of the WWER-1000 reactor fuel assemblies is observed up to now. The scale of this bow reduced significantly but it still effects safety. Even a minor bow available may lead to the noticeable increase of power of individual fuel pins associated with the local variation of the coolant amount. This effect must be taken into account on designing fuel loadings to eliminate the exceeding of set limitations. The introduction of additional special margins is the standard method for taking this effect into account. The present paper describes the conservative technique for the assessment of additional margins for bow of fuel assemblies of state-of-the-art designs. This technique is employed in the WWER-1000 reactor designing. The chosen conservatism degree is discussed as well as the method for its assurance and acceptable ways for its slackening. The example of the margin evaluation for the up-to-date fuel loading is given. (authors)

The solution of the LEU and MOX WWER-1000 calculation benchmark with the CARATE - multicell code

International Nuclear Information System (INIS)

Hordosy, G.; Maraczy, Cs.

2000-01-01

Preparations for disposition of weapons grade plutonium in WWER-1000 reactors are in progress. Benchmark: Defined by the Kurchatov Institute (S. Bychkov, M. Kalugin, A. Lazarenko) to assess the applicability of computer codes for weapons grade MOX assembly calculations. Framework: 'Task force on reactor-based plutonium disposition' of OECD Nuclear Energy Agency. (Authors)

Main examination results of WWER-1000 fuel after its irradiation in power reactors

Energy Technology Data Exchange (ETDEWEB)

Bibiliashvili, Yu [Vsesoyuznyj Nauchno-Issledovatel` skij Inst. Neorganicheskikh Materialov, Moscow (Russian Federation); Dubrovin, K [Russian Research Centre Kurchatov Inst., Moscow (Russian Federation); Vasilchenko, I [Opytno-Konstruktorskoe Byuro Gidropress, Podol` sk (Russian Federation); Yenin, A; Kushmanov, A [AO Novosibirskij Zavod Khimcontsentratov, Novosibirsk (Russian Federation); Smirnov, A; Smirnov, V [Nauchno-Issledovatel` skij Inst. Atomnykh Reaktorov, Dimitrovgrad (Russian Federation)

1994-12-31

WWER-1000 fuel examination has been undertaken to specify the properties of fuel assembly members by defining the parameters of their materials and their interconnection in power reactor operation conditions. Nine fuel assemblies are examined. The examination program includes: visual inspection, measurement of overall dimensions, eddy-current test, gamma-scanning, X-ray and neutron radiography, analysis of gas pressure and composition inside fuel rods, ceramography/metallography, mass spectrometry, microanalysis and electron microscopy of fuel and fuel claddings. The examination results suggest that WWER-1000 fuel spent at steady-state operation conditions up to 50 Mwd/kg U of burnup is in satisfactory condition. The examination of all types of fuel cladding failures indicates that the reason lies in the interaction of cladding with coolant solid impurities. The nodular cladding corrosion of fuel assembly discharged from the South-Ukrainian NPP is caused by the graphite compounds deposited on the fuel rod. Those deposits are a result of the circulating pump damage and had accidental, non-typical character. Some of the rods were found to have a small cladding `fretting` of the spacer grid cell material. The values of the majority of parameters determining the fuel efficiency allow to assume that there is a potential for further extension of fuel burnup and operation length. 1 tab., 11 figs.

Main examination results of WWER-1000 fuel after its irradiation in power reactors

International Nuclear Information System (INIS)

Bibiliashvili, Yu.; Dubrovin, K.; Vasilchenko, I.; Yenin, A.; Kushmanov, A.; Smirnov, A.; Smirnov, V.

1994-01-01

WWER-1000 fuel examination has been undertaken to specify the properties of fuel assembly members by defining the parameters of their materials and their interconnection in power reactor operation conditions. Nine fuel assemblies are examined. The examination program includes: visual inspection, measurement of overall dimensions, eddy-current test, gamma-scanning, X-ray and neutron radiography, analysis of gas pressure and composition inside fuel rods, ceramography/metallography, mass spectrometry, microanalysis and electron microscopy of fuel and fuel claddings. The examination results suggest that WWER-1000 fuel spent at steady-state operation conditions up to 50 Mwd/kg U of burnup is in satisfactory condition. The examination of all types of fuel cladding failures indicates that the reason lies in the interaction of cladding with coolant solid impurities. The nodular cladding corrosion of fuel assembly discharged from the South-Ukrainian NPP is caused by the graphite compounds deposited on the fuel rod. Those deposits are a result of the circulating pump damage and had accidental, non-typical character. Some of the rods were found to have a small cladding 'fretting' of the spacer grid cell material. The values of the majority of parameters determining the fuel efficiency allow to assume that there is a potential for further extension of fuel burnup and operation length. 1 tab., 11 figs

Analysis of WWER 1000 SG cold collector cracking

International Nuclear Information System (INIS)

Matocha, K.; Wozniak, J.

2000-01-01

Following the recommendations of the 1993 consultants' meeting on 'Steam Generator Collector Integrity of WWER 1000 Reactors', an extensive experimental program was started with the aim of finding the dominant damage mechanism responsible for cold collector cracking in steam generators, and of determining whether proper operating conditions can make the operation of VITKOVICE-produced steam generators safe throughout their lifetime. The experiments consisted of: a study of the effect of strain and thermal ageing and dissolved oxygen content on subcritical crack growth in 10GN2MFA steel; a study of the effect of high temperature water and tube expansion technology on the fracture behaviour of ligaments between holes for heat exchange tubes; a study of the effect of drilling, tube expansion technology and heat treatment on residual stresses on the surface of holes for heat exchange tubes. Details of the experimental techniques used are given as well as a discussion of the results obtained and presented in tables and graphs. (A.K.)

Two-dimensional full-core transport theory Benchmarks for the WWER reactors

International Nuclear Information System (INIS)

Petkov, P.T.

2002-01-01

Several two-dimensional full-core real geometry many-group steady-state problems for the WWER-440 and WWER-1000 reactors have been solved by the MARIKO code, based on the method of characteristics. The reference transport theory solutions include assembly-wise and pin-wise power distributions. Homogenized two-group diffusion parameters and discontinuity factors have been calculated by MARIKO for each assembly type both for the whole assembly and for each cell in the smallest sector of symmetry, using the B1 method for calculation of the critical spectrum. Accurate albedo-type boundary conditions have been calculated by MARIKO for the core-reflector and core-absorber boundaries, both for each outer assembly face and for each outer cell face. Comparison with the reference solutions of the two-group nodal diffusion code SPPS-1.6 and the few-group fine-mesh diffusion codes HEX2DA and HEX2DB are presented (Authors)

Mechanical properties and microstructure of long term thermal aged WWER 440 RPV steel

Energy Technology Data Exchange (ETDEWEB)

Kolluri, M., E-mail: kolluri@nrg.eu [Nuclear Research & Consultancy Group (NRG), P.O. Box 25, 1755 ZG Petten (Netherlands); Kryukov, A. [Scientific and Engineering Centre for Nuclear and Radiation Safety, 107140 Moscow (Russian Federation); Magielsen, A.J. [Nuclear Research & Consultancy Group (NRG), P.O. Box 25, 1755 ZG Petten (Netherlands); Hähner, P. [European Commission, Joint Research Centre, Directorate G – Nuclear Safety and Security, P.O. Box 2, 1755 ZG Petten (Netherlands); Petrosyan, V. [Armenian Scientific Research Institute for Nuclear Plant Operation (ARMATOM), 0027 Yerevan (Armenia); Sevikyan, G. [Armenian Nuclear Power Plant (ANPP), 0911, Metsamor, Armavir Marz (Armenia); Szaraz, Z. [European Commission, Joint Research Centre, Directorate G – Nuclear Safety and Security, P.O. Box 2, 1755 ZG Petten (Netherlands)

2017-04-01

The integrity assessment of the Reactor Pressure Vessel (RPV) is essential for the safe and Long Term Operation (LTO) of a Nuclear Power Plant (NPP). Hardening and embrittlement of RPV caused by neutron irradiation and thermal ageing are main reasons for mechanical properties degradation during the operation of an NPP. The thermal ageing-induced degradation of RPV steels becomes more significant with extended operational lives of NPPs. Consequently, the evaluation of thermal ageing effects is important for the structural integrity assessments required for the lifetime extension of NPPs. As a part of NRG's research programme on Structural Materials for safe-LTO of Light Water Reactor (LWR) RPVs, WWER-440 surveillance specimens, which have been thermal aged for 27 years (∼200,000 h) at 290 °C in a surveillance channel of Armenian-NPP, are investigated. Results from the mechanical and microstructural examination of these thermal aged specimens are presented in this article. The results indicate the absence of significant long term thermal ageing effect of 15Cr2MoV-A steel. No age hardening was detected in aged tensile specimens compared with the as-received condition. There is no difference between the impact properties of as-received and thermal aged weld metals. The upper shelf energy of the aged steel remains the same as for the as-received material at a rather high level of about 120 J. The T{sub 41} value did not change and was found to be about 10 °C. The microstructure of thermal aged weld, consisting carbides, carbonitrides and manganese-silicon inclusions, did not change significantly compared to as-received state. Grain-boundary segregation of phosphorus in long term aged weld is not significant either which has been confirmed by the absence of intergranular fracture increase in the weld. Negligible hardening and embrittlement observed after such long term thermal ageing is attributed to the optimum chemical composition of 15Cr2MoV-A for high

Integration of post-irradiation examination results of failed WWER fuel rods

International Nuclear Information System (INIS)

Smirnov, A.; Markov, D.; Smirnov, V.; Polenok, V.; Perepelkin, S.

2003-01-01

The aim of the work is to investigate the causes of WWER fuel rod failures and to reveal the dependence of the failed fuel rod behaviour and state on the damage characteristics and duration of their operation in the core. The post-irradiation examination of 12 leaky fuel assemblies (5 for WWER-440 and 7 for WWER-1000) has been done at SSC RF RIAR. The results show that the main mechanism responsible for the majority of cases of the WWER fuel rod perforation is debris-damage of the claddings. Debris fretting of the claddings spread randomly over the fuel assembly cross-section and they are registered in the area of the bundle supporting grid or under the lower spacer grids along the fuel assembly height. In the WWER fuel rods, the areas of secondary hydrogenating of cladding are spaced from the primary defects by ∼2500-3000 mm, as a rule, and are often adjacent closely to the upper welded joints. There is no pronounced dependence of the distance between the primary and secondary cladding defects neither on the linear power, at which the fuel rods were operated, nor on the period of their operation in the leaky state. The time period of the significant secondary damage formation is about 250 ± 50 calendar days for the WWER fuel rods with slight through primary defects (∼0.1 - 0.5 mm 2 ) operated in the linear power range 170-215 W/cm. Cladding degradation, taking place due to the secondary hydrogenating, does not occur in case of large through debris-defects during operation up to 600 calendar days

Problems of WWER-440 dynamic changes

International Nuclear Information System (INIS)

Rydzi, S.

1986-01-01

The data processing capability of the DYNAMIKA program is presented and demonstrated for the calculation of coolant parameters and heat transfer variables of the WWER reactor in accident and transient modes of operation. An experimental outage is described of the TG 11 turbogenerator at the V-1 Jaslovske Bohunice nuclear power plant. The measured values were compared with values calculated using the DYNAMIKA program. The graphic representation makes it evident that the mathematical model comes very close to reality. (J.B.)

About reliability of WWER pressure vessel neutron fluence calculation

Energy Technology Data Exchange (ETDEWEB)

Belousov, S; Ilieva, K; Antonov, S [Bylgarska Akademiya na Naukite, Sofia (Bulgaria). Inst. za Yadrena Izsledvaniya i Yadrena Energetika

1996-12-31

This reliability study was carried out under a Research Contracts F111 and TH-324 of the Bulgarian Ministry of Higher Education and the IAEA. The effect of geometry approximation and the choice of neutron cross-sections on the calculation model is estimated. The neutron flux onto reactor pressure vessel at locations, important for metal embrittlement surveillance, has been calculated using the codes TORT and DORT. The flux values calculated for both WWER-440 and WWER-1000 show good consistency within the limits of solution accuracy. It is concluded that the synthesis method (DORT) can be used for calculations at a reasonable cost whenever metal embrittlement surveillance is considered. Using an iron sphere benchmark measurement, a comparison of an experimental leakage spectrum with spectrum calculated using multigroup neutron cross-sections based on ENDF/B-4 and ENDF/B-6 data is performed. In the energy region above 1 MeV the best agreement with the experiment is achieved for ENDF/B-6 in VITAMIN-E group structure. 7 refs., 1 fig., 4 tabs.

About reliability of WWER pressure vessel neutron fluence calculation

International Nuclear Information System (INIS)

Belousov, S.; Ilieva, K.; Antonov, S.

1995-01-01

This reliability study was carried out under a Research Contracts F111 and TH-324 of the Bulgarian Ministry of Higher Education and the IAEA. The effect of geometry approximation and the choice of neutron cross-sections on the calculation model is estimated. The neutron flux onto reactor pressure vessel at locations, important for metal embrittlement surveillance, has been calculated using the codes TORT and DORT. The flux values calculated for both WWER-440 and WWER-1000 show good consistency within the limits of solution accuracy. It is concluded that the synthesis method (DORT) can be used for calculations at a reasonable cost whenever metal embrittlement surveillance is considered. Using an iron sphere benchmark measurement, a comparison of an experimental leakage spectrum with spectrum calculated using multigroup neutron cross-sections based on ENDF/B-4 and ENDF/B-6 data is performed. In the energy region above 1 MeV the best agreement with the experiment is achieved for ENDF/B-6 in VITAMIN-E group structure. 7 refs., 1 fig., 4 tabs

Report of the review of WWER-1000 safety issues resolution at Temelin nuclear power plant, Temelin, Czech Republic 11 to 15 March 1996

International Nuclear Information System (INIS)

Almeida, C.; Hoehn, J.; Seiberling, R.; Chambon, J.L.; Fil, N.S.; Munoz, A.; Roennberg, G.; Wenk, W.

1996-01-01

At the request of the Government of the Czech Republic, the IAEA conducted, in the period of 11-15 March 1996, a mission to review the resolution of WWER-1000 safety issues at Temelin NPP. These safety issues have been identified for WWER-1000 model 320 reactors and ranked according to their importance to safety in the frameworks of the IAEA Extrabudgetary Programme on Safety of WWER and RBMK Nuclear Power Plants. The Temelin NPP is a WWER-1000 and was originally designed according to standards of the former Soviet Union. After a series of reviews in the 1980s, a decision was taken by the Temelin NPP management to upgrade the design of Temelin, including the supply of fuel and instrumentation and control by a western company. The objective of the mission was to review the response of Temelin to the safety issues identified by the IAEA. The mission assessed the current Temelin design, including proposed modifications and plans for operation at Temelin, in the light of the IAEA recommendations for each relevant issue. The present report contains the mission's general conclusions and recommendations and an overview of the review performed in each topical area. The attachment contains a brief summary of the discussions on each individual safety issue and associated conclusions and recommendations. 3 refs

Conception of programs for evaluating balance indices of operation of WWER-440 nuclear power plants

International Nuclear Information System (INIS)

Zadrazil, J.

1986-01-01

The procedures are discussed of writing computation programs for the evaluation of basic technical and economic parameters of the operation of WWER-440 nuclear power plants. The criterion of the evaluation is the maximum power supply to the grid together with the required supply of heat, with the observance of safe operating conditions. Previous procedures of evaluation are compared with present procedures based on the use of a monitoring and evaluation system of the KOMPLEX-URAN 2 M type. The mathematical model of the program is based on balance equations and relations derived for actual measuring systems and is completed with an assessment of the reliability of input and output data. The flow chart is shown of the algorithm for the evaluation of technical and economic parameters, and methods are suggested for improving and extending the program. (J.C.)

Kozloduy NPP WWER-440/230 reactor pressure vessel radiation lifetime

Energy Technology Data Exchange (ETDEWEB)

Vodenicharov, S [Bylgarska Akademiya na Naukite, Sofia (Bulgaria). Inst. po Metaloznanie i Tekhnologiya na Metalite; Kamenova, Tz [Bylgarska Akademiya na Naukite, Sofia (Bulgaria). Inst. po Metaloznanie i Tekhnologiya na Metalite; Tzokov, P; Videnov, A [Kombinat Atomna Energetika, Kozloduj (Bulgaria); Pekov, B [Committee on the Use of Atomic Energy for Peaceful Purposes, Sofia (Bulgaria)

1996-12-31

The processes of metal embrittlement induced by neutron irradiation embrittlement (NIE) and neutron re-irradiation embrittlement (NRE) of the rector pressure vessel (RPV) are investigated. Radiation lifetime is calculated using two approaches for re-embrittlement: a conservative law and a lateral shift of the critical transition temperature curve after neutron irradiation. In order to prevent NIE the following measures have been taken at the Kozloduy NPP: loading of dummy elements into core periphery; heating the water for emergency core cooling to 55{sup o} C; fast acting valves in the main steam piping, etc. The critical embrittlement temperature, the residual part of temperature shift and the radiation lifetime have been calculated for units 1 - 4 using the two approaches and updated information on P and Cu impurities content. It is concluded that if the lateral re-embrittlement law is adopted and the P content does not exceed 0.05%, all RPV should reach their design lifetime. The NIE in WWER-440/230 is related to C and P content in the weld 4 and is negligible for the Unit 4 in particular, which has low impurities content. In order to reach the design lifetime of the Units 1 - 3 it is necessary to install MSIV. A verification of chemical composition of the Unit 1 RPV weld 4 metal is recommended. 7 refs., 3 figs., 6 tabs.

Kozloduy NPP WWER-440/230 reactor pressure vessel radiation lifetime

International Nuclear Information System (INIS)

Vodenicharov, S.; Pekov, B.

1995-01-01

The processes of metal embrittlement induced by neutron irradiation embrittlement (NIE) and neutron re-irradiation embrittlement (NRE) of the rector pressure vessel (RPV) are investigated. Radiation lifetime is calculated using two approaches for re-embrittlement: a conservative law and a lateral shift of the critical transition temperature curve after neutron irradiation. In order to prevent NIE the following measures have been taken at the Kozloduy NPP: loading of dummy elements into core periphery; heating the water for emergency core cooling to 55 o C; fast acting valves in the main steam piping, etc. The critical embrittlement temperature, the residual part of temperature shift and the radiation lifetime have been calculated for units 1 - 4 using the two approaches and updated information on P and Cu impurities content. It is concluded that if the lateral re-embrittlement law is adopted and the P content does not exceed 0.05%, all RPV should reach their design lifetime. The NIE in WWER-440/230 is related to C and P content in the weld 4 and is negligible for the Unit 4 in particular, which has low impurities content. In order to reach the design lifetime of the Units 1 - 3 it is necessary to install MSIV. A verification of chemical composition of the Unit 1 RPV weld 4 metal is recommended. 7 refs., 3 figs., 6 tabs

Partially closed fuel cycle of WWER-440

International Nuclear Information System (INIS)

Darilek, P.; Sebian, V.; Necas, V.

2002-01-01

Position of nuclear energy at the energy sources competition is characterised briefly. Multi-tier transmutation system is outlined out as effective back-end solution and consequently as factor that can increase nuclear energy competitiveness. LWR and equivalent WWER are suggested as a first tier reactors. Partially closed fuel cycle with combined fuel assemblies is briefed. Main back-end effects are characterised (Authors)

Experience running in and improvement of secondary circuit water chemistry of Kalinin NPP WWER-1000

International Nuclear Information System (INIS)

Noev, V.V.; Kukharev, N.D.; Otchenashev, G.D.; Guzeeva, G.I.; Kochetova, G.G.

1991-01-01

Basic characteristics of the secondary circuit water-chemical conditions at the Kalinin 1 and 2 reactors are presented. These are the WWER-1000 reactors with K-1000-1500 turbines. The analysis conducted makes it possible to conclude that all indicated values can meet the standards by introducing the hydrazine-ammonium regime in the secondary circuit with feedwater pH value equal to 9±0.2. Realization of design scheme for condensate-feeding circuit washing is necessary for acceleration of the water-chemical mode stabilization. Moreover the units should be equipped with automated chemical control instrumentation of a new generation

Effect of increased fuel exploitation on the main characteristics of spent WWER 440 fuel

International Nuclear Information System (INIS)

Zib, A.

2001-01-01

The article deals with the effect of a higher fuel exploitation on the main characteristics (particularly radioactivity and decay heat power) of spent WWER 440 fuel. The main characteristics were calculated by using the Origen code. The study was implemented as a three-stage process. In the first stage, the radioactivity and residual thermal power time evolution values were calculated for the 'typical fuel', i. e. fuel assembly with initial enrichment of 3.6% U-235, 3 years in reactor, and burnup of 30 MWd/kg U. In the second stage, ceteris paribus radioactivity and thermal power analyses of sensitivity to changes in the fuel burnup, initial fuel enrichment, and time in reactor were carried out for the typical fuel assembly. In the third stage, the effect of changes in all three variables was investigated for fuel assemblies possessing parameters that approach those applied at the Dukovany NPP. The effect of a higher fuel exploitation on the interim fuel storage is also mentioned. (author)

Thermal-hydraulic analysis of total loss of steam generator feed water in WWER-440

International Nuclear Information System (INIS)

Sabotinov, L.; Cadet-Mercier, S.

2001-01-01

The analysis is carried out for a WWER-440/V270 with upgraded primary safety valves (replacement of the existing PRZ safety valves with Pilot Operated Relief Valves (PORV) of the type SEBIM (France)) The current analysis is focused on the scenario 'Total Loss of SGs Feed Water' with application of the operator action of primary system 'Feed and Bleed' in order to check the effectiveness of the installed pressurizer SEBIM valves and to verify that the operator can cool down the reactor system and cope with this accident. The calculations have been performed at the Institute of Protection and Nuclear Safety (IPSN) in Fontenay-aux-Roses with the computer code CATHARE 2 Version 1.3L1. CATHARE is a French best estimate thermal-hydraulic program for accident analysis in the light water nuclear reactors, developed with the participation of the IPSN (Institut de Protection et Surete Nucleaire), CEA (Commissariat a l'Energie Atomique), Framatome and EdF (Electricite de France). (author)

WWER water chemistry related to fuel cladding behaviour

Energy Technology Data Exchange (ETDEWEB)

Kysela, J; Zmitko, M [Nuclear Research Inst. plc., Rez (Czech Republic); Vrtilkova, V [Nuclear Fuel Inst., Prague (Czech Republic)

1997-02-01

Operational experience in WWER primary water chemistry and corrosion related to the fuel cladding is reviewed. Insignificant corrosion of fuel cladding was found which is caused by good corrosion resistance of Zr1Nb material and relatively low coolant temperature at WWER-440 reactor units. The differences in water chemistry control is outlined and an attention to the question of compatibility of Zircaloys with WWER water chemistry is given. Some results of research and development in field of zirconium alloy corrosion behaviour are discussed. Experimental facility for in-pile and out-of-pile cladding material corrosion testing is shown. (author). 14 refs, 5 figs, 3 tabs.

WWER-440 reactor thermal power increase. Up-to-date approaches to substantiation of the core heat-engineering reliability

International Nuclear Information System (INIS)

Vasilchenko, I.; Lushin, V.; Zubtsov, D.

2006-01-01

Increasing the Units power is an urgent problem for nuclear power plants with WWER-440 reactors. Improving the fuel assembly designs and calculated codes creates all prerequisites to fulfil this purpose. The decrease in the core power peaking is reached by using the profiled fuel assemblies, burnable absorber integrated into the fuel, the FA with the modernized interface attachment, modern calculated codes that allows to reduce conservatism of the RP safety substantiation. A wide spectrum of experimental study of behaviour of the fuel having reached burn-up (50-60) MW days / kg U under the transients and accident conditions was carried out, the post-irradiated examination of the fuel assemblies, fuel rods and fuel pellets with four and five annual operating fuel cycle were performed as well and confirmed the high reliability of the fuel, the presence of large margins of the fuel stack state that contributes to reactor operation at the increased power. The results of the carried out experiments on implementing the five and six annual fuel cycles show that the limiting fuel state as to its serviceability in the WWER-440 reactors is far from being reached. Presently there is an experience of the increased power operation of Kola NPP, Units 1, 2, 4 and Rovno NPP, Unit 2. The Loviisa NPP Units are operated at 109 % power. The Russian experts had gained an experience in substantiating the core operation at 108 % power for Paks NPP, Unit 4. In this paper the additional conditions for increasing the power of the Kola NPP, Units 1 and 2 and the main results of substantiation of increase in power of the Paks NPP, Unit 4 up to 1485 MW are presented in details

Main building complex WWER 440/213 upper range design response spectra for soft soil site conditions (Paks)

International Nuclear Information System (INIS)

Krutzik, N.

1996-01-01

Within the Benchmark studies parallel investigation were prepared for the main building complex of the WWER-440/213 Paks NPP by several participating institutions. The investigations were based on various mathematical models and procedures but all had the same seismological data as input. The calculation methods as well as software tools were different. This report covers the enveloped response results which were the basis for the benchmark studies and which should be used for upgrading of mechanical and electrical components and systems which will follow. These response spectra which consider a certain conservatism namely neglecting the frequency independence of the stiffness and the cut-off of damping values are named 'Upper Range design Benchmark Response Spectra' for the main building of Paks NPP

Main building complex WWER 440/213 upper range design response spectra for soft soil site conditions (Paks)

Energy Technology Data Exchange (ETDEWEB)

Krutzik, N [Siemens AG, Power Generation Group (KWU) NDA2, Offenbach (Germany)

1996-07-01

Within the Benchmark studies parallel investigation were prepared for the main building complex of the WWER-440/213 Paks NPP by several participating institutions. The investigations were based on various mathematical models and procedures but all had the same seismological data as input. The calculation methods as well as software tools were different. This report covers the enveloped response results which were the basis for the benchmark studies and which should be used for upgrading of mechanical and electrical components and systems which will follow. These response spectra which consider a certain conservatism namely neglecting the frequency independence of the stiffness and the cut-off of damping values are named 'Upper Range design Benchmark Response Spectra' for the main building of Paks NPP.

Analysis of expediency to set regulators of high-pressure emergency core cooling system of WWER 1000 (B-320)

International Nuclear Information System (INIS)

Skalozubov, V.I.; Komarov, Yu.A.; Tikhonova, G.G.; Nikiforov, S.N.; Bogodist, V.V.; Fol'tov, I.M.; Khadzh Faradzhallakh Dabbakh, A.

2011-01-01

The work shows that setting regulative valves in high-pressure emergency core cooling system of WWER 1000/B-320 can be effective only involving the additional tuning to account traverse speed of operating elements of regulator and configuration of the systems providing cooling of primary loop.

Safeguarding the nuclear safety of WWER-440 reactor pressure vessels at SKODA Plzen

International Nuclear Information System (INIS)

Hrbek, Z.

1986-01-01

The approach is described of the SKODA enterprise to safety assurance and to providing the reliability of WWER-440 reactor pressure vessels. The philosophy is analyzed of in-service inspection and determination of the residual service life of pressure vessels. This follows up on the so-called conception of basic safety whose main aim is to preclude failures at production stage by the selection of suitable material, namely by optimizing the choice of raw materials, of metallurgical procedures such as will lead to high purity of the pressure vessel material, by introducing multiple inspection in production, reducing the sensitivity of materials to technological operations, and by high-quality welds. The quality of in-service inspections is given by the use of technical diagnostic instruments of peak quality and of modern methods of nondestructive materials testing. The instruments and methods used are described. It is stated that the experience gained with in-service inspection will make it possible to draw up operating regulations and safety criteria for nuclear installations and own inspection regulations, this with regard to technical and economic factors. (Z.M.)

Definition of the seventh dynamic AER benchmark-WWER-440 pressure vessel coolant mixing by re-connection of an isolated loop

International Nuclear Information System (INIS)

Kotsarev, A.; Lizorkin, M.; Petrin, R.

2010-01-01

The seventh dynamic benchmark is a continuation of the efforts to validate systematically codes for the estimation of the transient behavior of VVER type nuclear power plants. This benchmark is a continuation of the work in the sixth dynamic benchmark. It is proposed to be simulated the transient - re-connection of an isolated circulating loop with low temperature or low boron concentration in a VVER-440 plant. It is supposed to expand the benchmark to other cases when a different number of loops are in operation leading to different symmetric and asymmetric core boundary conditions. The purposes of the proposed benchmark are: 1) Best-estimate simulations of an transient with a coolant flow mixing in the Reactor Pressure Vessel of WWER-440 plant by re-connection of one coolant loop to the several ones on operation, 2) Performing of code-to-code comparisons. The core is at the end of its first cycle with a power of 1196.25 MWt. The basic additional difference of the 7-seventh benchmark is in the detailed description of the downcomer and bottom part of the reactor vessel that allow describing the effects of coolant mixing in the Reactor Pressure Vessel without any additional conservative assumptions. The burn-up and the power distributions at this reactor state have to be calculated by the participants. The thermohydraulic conditions of the core in the beginning of the transient are specified. Participants self-generated best estimate nuclear data is to be used. The main geometrical parameters of the plant and the characteristics of the control and safety systems are also specified. Use generated input data decks developed for a WWER-440 plant and for the applied codes should be used. The behaviour of the plant should be studied applying coupled system codes, which combine a three-dimensional neutron kinetics description of the core with a pseudo or real 3D thermohydraulics system code. (Authors)

Methodology of thermalhydraulic tests of fuel assemblies for WWER-1000

International Nuclear Information System (INIS)

Archipov, A.; Kolochko, V.N.

2001-01-01

At present 11 units with WWER-1000 are in operation in Ukraine. The NPPs are provided with nuclear fuel from Russia. The fuel assemblies are fabricated and delivered to Ukrainian NPPs from Russia. However the contemporary tendencies of nuclear energy development in the world assume a diversification of nuclear fuel vendors. Therefore the creation of the own nuclear fuel cycle of Ukraine is in mind in the strategy of nuclear energy development of Ukraine. As a part of the fuel assemblies fabrication process complex of the thermalhydraulic tests should be carried out to confirm design characteristics of the fuel assemblies before they are loaded in the reactor facility. The experimental basis and scientific infrastructure for the thermalhydraulic tests arrangement and realization of the programs and procedures for the core equipment examination are under consideration. (author)

The main conditions ensured problemless implementation of 235U high enriched fuel in Kozloduy NPP (Bulgaria) - WWER-1000 Units

International Nuclear Information System (INIS)

Dobrevski, I.; Zaharieva, N.; Minkova, K.; Michaylov, G.; Penev, P.; Gerchev, N.

2009-01-01

The collected water chemistry and radiochemistry data during the operation of the Kozloduy NPP Unit 5 for the period 2006-2009 (12-th, 13-th 14-th and 15-th fuel cycles) undoubtedly indicate for WWER-1000 Units (whose specific features are: Steam generators with austenitic stainless steel 08Cr18N10T tubing; Steam generators are with horizontal straight tubing and Fuel elements cladding material is Zr-1%Nb (Zr1Nb) alloy), that one realistic way for problemless implementation of 235 U high enriched fuel have been found. The main feature characteristics of this way are: Implementation of solid neutron burnable absorbers together with the dissolved in coolant neutron absorber - natural boric acid; Application of fuel cladding materials with enough corrosion resistance by the specific fuel cladding environment created by presence of SNB; Keeping of suitable coolant water chemistry which ensures low corrosion rates of core- and out-of-core- materials and limits in core (cladding) depositions and restricts out-of-core radioactivity buildup. The realization of this way in WWER-1000 Units in Kozloduy NPP was practically carried out through: 1) Implementation of Russian fuel assemblies TVSA which have as fuel cladding material E-110 alloy (Zr1Nb) with enough high corrosion resistance by presence of sub-cooled nucleate boiling (SNB) and use burnable absorber (Gd) integrated in the uranium-gadolinium (U-Gd 2 O 3 ) fuel (fuel rod with 5.0% Gd 2 O 3 ); 2) Development and implementation of water chemistry primary circuit guidelines, which require the relation between boric acid concentration and total alkalising agent concentrations to ensure coolant pH 300 = 7.0 - 7.2 values during the whole operation period. The above mentioned conditions by the passing of WWER-1000 Units in NPP Kozloduy to uranium fuel with 4.4% 235 U (TVSA fuel assemblies) practically ensured avoidance of the creation of the necessary conditions for AOA onset. The operational experience (2006-2009) of the

Testing of acoustic emission method during pressure tests of WWER-440 steam generators and pressurizers

International Nuclear Information System (INIS)

Wuerfl, K.; Crha, J.

1987-01-01

The results are discussed of measuring acoustic emission in output pressure testing of steam generators and pressurizers for WWER-440 reactors. The objective of the measurements was to test the reproducibility of measurements and to find the criterion which would be used in assessing the condition of the components during manufacture and in operation. The acoustic emission was measured using a single-channel Dunegan/Endevco apparatus and a 16-channel LOCAMAT system. The results showed that after the first assembly, during a repeat dismantle of the lids and during seal replacement, processes due to seal contacts and bolt and washer deformations were the main source of acoustic emission. A procedure was defined of how to exclude new acoustic emission sources in such cases. The acoustic emission method can be used for the diagnostics of plastic deformation processes or of crack production and propagation in components during service. (Z.M.)

An approach to WWER fuels with BaCo

International Nuclear Information System (INIS)

Marino, A.; Demarco, G.

2008-01-01

BaCo is a code for the simulation of the behaviour of a nuclear fuel rod under operation conditions. BaCo, a quasi 2D code based on a finite differences scheme, has been used for simulating PHWR, CANDU, PWR, BWR, MOX, WWER, and experimental fuel rods. We improve the performance of BaCo with a set of tools based on the method of finite elements for 3D analysis of the stress-strain state. We can simulate any UO 2 pellet geometry. Standard WWER-440 fuel assemblies irradiated in the Kola-3 reactor of the CRP FUMEX II of the IAEA were the first WWER simulations with BaCo. We find a very good agreement among our calculations, the experimental results and other qualified fuel codes. We present the BaCo code and our results for PWR and WWER fuels of the CRP FUMEX II, the 3D analysis of WWER fuel pellet and the projections of these results with the Argentinean nuclear fuels development. (authors)

Fuel cycles of WWER-1000 based on assemblies with increased fuel mass

International Nuclear Information System (INIS)

Kosourov, E.; Pavlovichev, A.; Shcherenko, A.

2011-01-01

Modern WWER-1000 fuel cycles are based on FAs with the fuel column height of 3680 mm, diameters of the fuel pellet and its central hole of 7.6 and 1.2 mm respectively. The highest possible fuel enrichment has reached its license limit that is 4.95 %. Research in the field of modernization, safety justification and licensing of equipment for fuel manufacture, storage and transportation are required for further fuel enrichment increase (above 5 %). So in the nearest future an improvement of technical and economic characteristics of fuel cycles is possible if assembly fuel mass is increased. The available technology of the cladding thinning makes it possible. If the fuel rod outer diameter is constant and the clad inner diameter is increased to 7.93 mm, the diameter of the fuel pellet can be increased to 7.8 mm. So the suppression of the pellet central hole allows increasing assembly fuel weight by about 8 %. In this paper we analyze how technical and economic characteristics of WWER-1000 fuel cycle change when an advanced FA is applied instead of standard one. Comparison is made between FAs with equal time interval between refueling. This method of comparison makes it possible to eliminate the parameters that constitute the operation component of electricity generation cost, taking into account only the following technical and economic characteristics: 1)cycle length; 2) average burnup of spent FAs; 3) specific natural uranium consumption; 4)specific quantity of separative work units; 5) specific enriched uranium consumption; 6) specific assembly consumption. Collected data allow estimating the efficiency of assembly fuel weight increase and verifying fuel cycle characteristics that may be obtained in the advanced FAs. (authors)

Modelling of WWER-1000 steam generators by REALP5/MOD3.2 code

Energy Technology Data Exchange (ETDEWEB)

D`Auria, F.; Galassi, G.M. [Univ. of Pisa (Italy); Frogheri, M. [Univ. of Genova (Italy)

1997-12-31

The presentation summarises the results of best estimate calculations carried out with reference to the WWER-1000 Nuclear Power Plant, utilizing a qualified nodalization set-up for the Relap5/Mod3.2 code. The nodalization development has been based on the data of the Kozloduy Bulgarian Plant. The geometry of the steam generator imposed drastic changes in noding philosophy with respect to what is suitable for the U-tubes steam generators. For the secondary side a symmetry axis was chosen to separate (in the nodalization) the hot and the cold sides of the tubes. In this way the secondary side of the steam generators was divided into three zones: (a) the hot zone including the hot collector and the hot l/2 parts of the tubes; (b) the cold zone including the cold collector and the cold 1/2 parts of the tubes; (c) the downcomer region, where down flow is assumed. As a consequence of above in the primary side more nodes are placed on the hot side of the tubes. Steady state and transient qualification has been achieved, considering the criteria proposed at the University of Pisa, utilizing plant transient data from the Kozloduy and the Ukrainian Zaporosche Plants. The results of the application of the qualified WWER-1000 Relap5/Mod3.2 nodalization to various transients including large break LOCA, small break LOCA and steam generator tube rupture, together with a sensitivity analysis on the steam generators, are reported in the presentation. Emphasis is given to the prediction of the steam generators performances. 23 refs.

Modelling of WWER-1000 steam generators by REALP5/MOD3.2 code

Energy Technology Data Exchange (ETDEWEB)

D` Auria, F; Galassi, G M [Univ. of Pisa (Italy); Frogheri, M [Univ. of Genova (Italy)

1998-12-31

The presentation summarises the results of best estimate calculations carried out with reference to the WWER-1000 Nuclear Power Plant, utilizing a qualified nodalization set-up for the Relap5/Mod3.2 code. The nodalization development has been based on the data of the Kozloduy Bulgarian Plant. The geometry of the steam generator imposed drastic changes in noding philosophy with respect to what is suitable for the U-tubes steam generators. For the secondary side a symmetry axis was chosen to separate (in the nodalization) the hot and the cold sides of the tubes. In this way the secondary side of the steam generators was divided into three zones: (a) the hot zone including the hot collector and the hot l/2 parts of the tubes; (b) the cold zone including the cold collector and the cold 1/2 parts of the tubes; (c) the downcomer region, where down flow is assumed. As a consequence of above in the primary side more nodes are placed on the hot side of the tubes. Steady state and transient qualification has been achieved, considering the criteria proposed at the University of Pisa, utilizing plant transient data from the Kozloduy and the Ukrainian Zaporosche Plants. The results of the application of the qualified WWER-1000 Relap5/Mod3.2 nodalization to various transients including large break LOCA, small break LOCA and steam generator tube rupture, together with a sensitivity analysis on the steam generators, are reported in the presentation. Emphasis is given to the prediction of the steam generators performances. 23 refs.

Physics measurements on WWER-440 diagnostic assemblies

International Nuclear Information System (INIS)

Dach, K.; Jirousek, V.; Kott, J.; Horak, J.; Teren, S.; Nemec, J.

1980-01-01

The aims of physics measurements using diagnostic assemblies are the development of neutron noise diagnostics methods, the improvement of knowledge of the physical properties of the WWER reactor cores, the testing of computer programs, and the specification of nuclear safety criteria and the obtaining of information allowing the optimum nuclear fuel economy. The instrumentation of diagnostic assemblies is briefly described, including miniature fission chambers, SPN detectors and calorimeters. The method of evaluating and experimental testing is shown. (M.S.)

Nuclear and thermal power plant power ramping capability

International Nuclear Information System (INIS)

Golovach, E.A.

1983-01-01

The possibilities of step power increase by NPP and TPP units under emergency conditions of power grids operation are considered. The data analysis has shown that power units ramping capability with WWER-440, WWER-1000 and RBMK-1000 reactors is higher than that of 300 MW power units on fossil fuel, at the initial time interval (0-30 s). These NPP power units satisfy as to ramping capability the energy system requirements. Higher NPP power units ramping capability is explained by the fact that relative pressure before turbine valves is decreased less than in straight-through boilers while the steam volumes time constant of steam separator-superheaters is less than that of intermediate superheatings. Higher power unit ramping capability with WWER-440 and RBMK-1000 reactors as compared with the WWER-1000 reactor is pointed out as well as the increase of WWER-1000 power unit capability using high-speed turbines

Comparative severe accident analysis of WWER 1000/B 320 LOCA DN100 computed by computer codes ASTEC V1.1 and SCDAP/RELAP5

International Nuclear Information System (INIS)

Kalchev, B.; Dimov, D.; Tusheva, P.; Mladenov, I.

2005-01-01

This paper presents the modelling approach for LOCA 100 mm sequence for WWER 1000-B 320 type of reactor with the integral ASTEC computer code and SCDAP/RELAP5 computer code. As a basic input deck the reference input file for Balakovo NPP from the released ASTEC CD has been applied. As a first part of the calculations for the SBLOCA sequence the ASTEC v1.1 modules CESAR, DIVA and CPA have been activated in a coupled mode. For SCDAP/RELAP5 calculation input deck for WWER 1000-B 320 has been applied which meant to be closer to the initial boundary conditions applied for ASTEC WWER 1000 input deck. A SBLOCA 100 mm comparison between ASTEC v1.1 and SCADAP/RELAP5 has been presented. ASTEC predicts vessel failure at 15620 s. ASTEC and SCDAP/RELAP5 give close but not similar results - this could be observed on the trends. The comparison of 100 mm-break shows that SCDAP/RELAP5 predicts clear phenomenological changes in primary pressure evolution and molten pool formation. Similar hydrogen production mass for both codes around 5000 s is detected

Seismic safety programme at NPP Paks. Propositions for coordinated international activity in seismic safety of the WWER-440 V-213

International Nuclear Information System (INIS)

Katona, T.

1995-01-01

This paper presents the Paks NPP seismic safety program, highlighting the specifics of the WWER-440/213 type in operation, and the results of work obtained so far. It covers the following scope: establishment of the seismic safety program (original seismic design, current requirements, principles and structure of the seismic safety program); implementation of the seismic safety program (assessing the seismic hazard of the site, development of the new concept of seismic safety for the NPP, assessing the seismic resistance of the building and the technology); realization of the seismic safety of higher level (technical solutions, drawings, realization); ideas and propositions for coordinated international activity

Evaluation of fatigue crack growth in the primary circuit pipeline of a WWER 440/213c type nuclear power plant

International Nuclear Information System (INIS)

Samohyl, P.

1993-07-01

The fatigue damage of the primary circuit of WWER-440/213c reactors was evaluated proceeding from actual and design operating data of units 3 and 4 of the Bohunice V-2 nuclear power plant. A complex computation model was set up, encompassing the main circulation pipeline, pressurizer pipeline, emergency core aftercooling system pipeline, steam pipeline, and feedwater pipeline. The standardized STATIC code was applied to the stress analysis, and the FATLBB code was used to determine the crack increment for all operating states and primary circuit sections. The probability of fatigue failure of the pipelines was found to be low. (J.B.). 55 tabs., 3 figs., 9 refs

Activities in the Czech Republic for reactor pressure components lifetime management

International Nuclear Information System (INIS)

Brumovsky, M.

1994-01-01

The following activities in the Czech republic for reactor pressure components lifetime management are described: upgrading and safety assurance of nuclear power plants (NPP) with reactors of WWER-440/V-230 type, safety assurance of NPPs with reactors of WWER-440/V-213, lifetime management programme of NPPs with WWER-440/V-213 reactors, preparation of start-up of NPPs with WWER-1000/V-320 reactors, preparation of guides for lifetime as well as defect allowability evaluation in main components of primary and secondary circuits. 3 figs

Nuclear safety analysis for transport cask TK-6 (for WWER-440) and cover for fresh assemblies (for WWER-1000) in implementation of new fuel types at Ukrainian NPP

International Nuclear Information System (INIS)

Bilodid, Y.; Kovbasenko, Iu; Dudka, Olena

2006-01-01

According to the fresh fuel management procedure, fuel assemblies - after nuclear fuel delivery to the NPP fresh fuel unit - are vertically loaded into a cover intended for the delivery of fuel assemblies into the containment of the NPP reactor compartment. The cover is placed into an universal jack in the cooling and refueling pond, and then the fresh fuel assemblies are loaded into the reactor core. Based on the nuclear safety analysis carried out by the Russian Research Center 'Kurchatov Institute' for contemporary WWER-1000 fuel, it has become necessary to limit the number of fuel assemblies loaded into a cover below its designed capacity (12 FA instead of 18 FA as originally designed). Such a decision leads to worse economic performances in fuel transportation. The paper considers potential ways to overcome this restriction. Transport container TK-6 for spent fuel assemblies was designed quite a long time ago and, as shown in this paper, the requirement on the maximally permissible neutron multiplication factor of the loaded container for individual states to be analyzed in compliance with Ukrainian regulations is not met. First of all, this concerns the container criticality analysis in optimal neutron slow-down (container filling with water-air mixture with optimal density). The paper shows potential ways for TK-6 burnup-credit loading with the maximum number of fuel assemblies and partial container loading (Authors)

Characterisation of the inventory of radioisotopes induced in the biological shield a WWER-440 reactor

International Nuclear Information System (INIS)

Feher, S.; Czifrus, Sz.; Zsolnay, E.M.; Szondi, E.

2001-01-01

A significant part of the radwaste originating from the decommissioning of NPPs is made up of the activated concrete and steel components of the biological shield. The paper presents the results of studies aimed at the determination of the amount of radionuclides accumulating in the serpentinous and ordinary concrete shield around the WWER-440 reactors of the Paks NPP. For the calculations, the reactor, vessel and shield were modelled in detail both in terms of geometry and material composition. The spatial and energy distribution of the activating neutron spectrum was determined by certain modules of SCALE 4.3 and the code TORT in two and three dimensions, while the activation was calculated using ORIGEN-S for 22 geometrical regions. The results showed that the activity of the concrete structures at final shutdown after 30 years of operation is approximately 50 TBq, which decreases to 20, 12, 1.1 TBq and 27 GBq after 1 month, 1 year, 10 and 100 years, respectively (Authors)

Technical basis for instrumentation and control design improvements in WWER-440/230 nuclear power plants. A publication of the extrabudgetary programme on the safety of WWER and RBMK nuclear power plants

International Nuclear Information System (INIS)

1996-01-01

Instrumentation and control (I and C) has been recognized as an area which requires substantial improvements in WWER NNPs, particularly for model 230 plants. Under contract with the IAEA the Spanish company Empresarios Agrupados (EA) developed a basic document proposing a technical basis for improvements related to the following most significant aspects of I and C: criteria for safety classification; remote shutdown panel; I and C support to operation and control room design; instrumentation set point margins; accident monitoring instrumentation. This publication is derived from the original report of EA which was circulated by the IAEA for review by staff members and experts from various Member States. It was finally agreed upon at a Consultants' meeting convened by the IAEA in Vienna in May 1994 with the participation of experts from France, Germany and Spain. The guidance expressed in this report is based on the IAEA/NUSS standards, safety guides and practices, and on regulations in use in various Member States. It is proposed as a way of carrying out the necessary studies to improve safety by upgrading the vital part of instrumentation an control in WWER-440 model 230 nuclear power plants. 28 refs, 3 figs

Some aspects of nuclear fuel utilisation at Ukrainian's NPPs during last two years

International Nuclear Information System (INIS)

Ieremenko, M.; Bilodid, Y.; Ovdiienko, Y.

2011-01-01

In the first part of the report the brief characteristic of the realized fuel cycles on Ukraine's NPPs, types of loaded fuel is described. Experience of new fuel type implementation are present (FA Second Generation for WWER-440. Westinghouse FA for WWER-1000). Next issue of report is the some of problem with fuel utilisation (leakage FA, problem with C b calculation and other). And the last issue of report is presentation of future new fuel implementation (WWER-440/1000). (authors)

Operational monitoring of temperature and state of stress of primary collectors, their stud bolts and cover and temperatures of steam generator's pressure vessel at the nuclear power unit WWER 440

International Nuclear Information System (INIS)

Matal, O.; Simo, T.; Holy, F.; Vejvoda, S.

1992-01-01

Both primary collectors of the WWER 440 steam generator (STGE) are vertically positioned inside the STGE pressure vessel and connected in their lower part to the primary piping and closed at their upper part by primary covers. The primary cover is pushed against the primary collector flange by 20 stud bolts. Two nickel packing rings are fitted between the primary cover and collector. A leakage in the collector-cover junction could cause flow of the radioactive water into the clean secondary water. If the junction is made in accordance with the Soviet standard design the computed stresses exceed the allowable value in the stud bolts by a factor of 1.5. Therefore an improved design of the primary collector - primary cover flange joint was designed and tested on one STGE at a WWER 440 nuclear power unit in Czechoslovakia. The paper describes the system of joint properties measurement, gives some substantial characteristics of the new stud bolts and primary cover design and comments on significant measured results of state of stress and temperatures in comparison with the operational regime of the STGE. (orig.)

RELAP5/MOD3.2 investigation of loss of in-house supply power for WWER 1000/320V

International Nuclear Information System (INIS)

Gencheva, R.; Pavlova, M.; Groudev, P.

2001-01-01

This paper discusses the results of the thermal-hydraulic investigations of the 'Loss of in-house supply power' accident at the Kozloduy NPP Unit 6. The RELAP5/MOD3.2 computer code has been used to stimulate the loss of in-house supply power accident in a WWER 1000 Nuclear Power Plant model. This model was developed at the Institute for Nuclear Research and Nuclear Energy for analyses of operational occurrences, abnormal events and design basis scenarios. It will provide a significant analytical capability for the Bulgarian technical specialists located at the Kozloduy NPP. The criteria used in selecting transient are: importance to safety, availability and suitability of data followed by suitability for RELAP5 code validation. The investigation of 'Loss of normal and reverse AC power' is a process that compares the analytical results obtained by RELAP5/MOD3.2 model of the WWER 1000 against experimental transient data obtained from Kozloduy NPP Unit 6. The comparisons between the RELAP5 results and the test data indicate good agreement

Approach to normalization of the secondary circuit water chemistry of NPP with WWER-1000

International Nuclear Information System (INIS)

Mamet, V.A.; Erpyleva, S.F.; Banyuk, G.F.

1998-01-01

The approach to normalization if indices of water-chemical regime of the secondary circuit of the NPP with WWER-1000 reactor, based on pH calculational values at the coolant working temperature in dependence on the normalized admixtures concentration is considered. The possibility for conducting the water regime of steam generators by the ratio of sodium concentration and electrical conductivity of H-cation sample of blow-through water is shown. The limitations (os action level) by deviation of normalized indices from recommended ones for normal operational conditions are described

Assessment of spent WWER-440 fuel performance under long-term storage conditions

Energy Technology Data Exchange (ETDEWEB)

Takats, F [TS Enercon Kft. (Hungary)

2012-07-01

Paks Nuclear Power Plant is the only NPP in Hungary. It has four WWER-440 type reactor units. The fresh fuel is imported from Russia so far. The spent fuel assemblies were shipped back to Russia until 1997 after about 6 years cooling at the plant. A dry storage facility (MVDS type) has been constructed and is operational since then. By 1 January 2008, there were 5107 assemblies in dry storage. The objectives are: 1) Wet AR storage of spent fuel from the NPP Paks: Measurements of conditions for spent fuel storage in the at-reactor (AR) storage pools of Paks NPP (physical and chemical characteristics of pool water, corrosion product data); Measurements and visual control of storage pool component characteristics; Evaluation of storage characteristics and conditions with respect to long-term stability (corrosion of fuel cladding, construction materials); 2) Dry AFR storage at Paks NPP: Calculation and measurement of spent fuel conditions during the transfer from the storage pool to the modular vault dry storage (MVDS) on the site; Calculation and measurement of spent fuel conditions during the preparation of fuel for dry storage (drying process), such as crud release, activity build-up; Measurement of spent fuel conditions during the long-term dry storage, activity data in the storage tubes and amount of crud.

Dynamic behavior structural response and capacity evaluation of the standardized WWER-1000 nuclear power plants subjected to severe loading conditions

International Nuclear Information System (INIS)

Ambriashvili, Y.K.; Krutzik, N.J.

1993-01-01

In order to verify the structural capacity of standardized WWER-1000 MW nuclear power plants, comprehensive static and dynamic analyses were performed in cooperation between Siemens and Atomenergoprojekt. The main goal of these investigations was to perform of a number of seismic analyses of standardized WWER-1000 reactor buildings on the basis of 13 given seismological inputs, taking into account the local soil conditions at 17 different sites defined by in-situ investigations. The analyses were based on appropriate mathematical models (equivalent beam models as well as detailed spatial surface element models) of the coupled vibrating structures (base structure, outer structure, containment, inner structure) and of the layered soil. The analyses were mainly performed using the indirect method (substructure method). Based on the results of the seismic analysis as well as the results of static analysis (pressure and temperature due to LOCA, dead weight, prestressing) an assessment was made of the seismic safety of the containment and the reactor building. Using a complex 3-dimensional model of the structure and the soil, the influence of the flexibility of the basement structure on the structural response was also studied. The structural analyses of the WWER-1000 reactor building led to the conclusion that its design accounts well for the main factors governing the dynamic behavior of the building. The assessment of the forces acting in the structures shows that the bearing capacity of the analyzed building structure corresponds to an earthquake intensity of about 0.2 g to 0.25 g

Relap5/Mod2.5 analyses of SG primary collector head rupture in WWER-440 reactor

International Nuclear Information System (INIS)

Szczurek, J.

1995-01-01

The paper presents the results of the analyses of steam generator (SG) manifold cover rupture performed with RELAP5/MOD2.5 (version provided by RMA, Albuquerque, for PC PPS). The calculations presented are based on RELAP5 input deck for WWER-440/213 Bobunice NPP, developed within the framework of IAEA TC Project RER/9/004. The presented analyses are directed toward determining the maximum amount of reactor coolant discharged into the secondary coolant system and the maximum amount of contaminated coolant release to the atmosphere. In all cases considered in the analysis, maximum ECCS injection capacity is assumed. The paper includes only the cases without any operator actions within the time period covered by the analyses. In particular, the primary loop isolation valves are not used for isolating the broken steam generator. Two scenarios are analysed: with and without the SG safety valve stuck open

Relap5/Mod2.5 analyses of SG primary collector head rupture in WWER-440 reactor

Energy Technology Data Exchange (ETDEWEB)

Szczurek, J. [Inst. of Atomic Energy, Swierk (Poland)

1995-12-31

The paper presents the results of the analyses of steam generator (SG) manifold cover rupture performed with RELAP5/MOD2.5 (version provided by RMA, Albuquerque, for PC PPS). The calculations presented are based on RELAP5 input deck for WWER-440/213 Bobunice NPP, developed within the framework of IAEA TC Project RER/9/004. The presented analyses are directed toward determining the maximum amount of reactor coolant discharged into the secondary coolant system and the maximum amount of contaminated coolant release to the atmosphere. In all cases considered in the analysis, maximum ECCS injection capacity is assumed. The paper includes only the cases without any operator actions within the time period covered by the analyses. In particular, the primary loop isolation valves are not used for isolating the broken steam generator. Two scenarios are analysed: with and without the SG safety valve stuck open. 3 refs.

Relap5/Mod2.5 analyses of SG primary collector head rupture in WWER-440 reactor

Energy Technology Data Exchange (ETDEWEB)

Szczurek, J [Inst. of Atomic Energy, Swierk (Poland)

1996-12-31

The paper presents the results of the analyses of steam generator (SG) manifold cover rupture performed with RELAP5/MOD2.5 (version provided by RMA, Albuquerque, for PC PPS). The calculations presented are based on RELAP5 input deck for WWER-440/213 Bobunice NPP, developed within the framework of IAEA TC Project RER/9/004. The presented analyses are directed toward determining the maximum amount of reactor coolant discharged into the secondary coolant system and the maximum amount of contaminated coolant release to the atmosphere. In all cases considered in the analysis, maximum ECCS injection capacity is assumed. The paper includes only the cases without any operator actions within the time period covered by the analyses. In particular, the primary loop isolation valves are not used for isolating the broken steam generator. Two scenarios are analysed: with and without the SG safety valve stuck open. 3 refs.

WWER steam generator tube structural and leakage integrity

International Nuclear Information System (INIS)

Splichal, K.; Krhounek, Vl.; Otruba, J.; Ruscak, M.

1998-01-01

The integrity of heat exchange tubes may influence the lifetime of WWER steam generators and appears to be an important criterion for the evaluation of their safety and operational reliability. The basic requirements are to assure very low probability of radioactive water leakage, preventing unstable crack growth and sudden tube rupture. These requirements led to development of permissible limits for primary to secondary leak evaluation and heat exchange tubes plugging. The stress corrosion cracking and pitting are the main corrosion damages of WWER heat exchange tubes and are initiated from the outer surface. Both the initiation and crack growth cause thinning of the tube wall and lead to part thickness cracks and through wall cracks, oriented preferentially in the axial direction. The paper presents the leakage and plugging limits for WWER steam generators, which have been determined from leak tests and burst tests. The tubes with axial part-through and through-wall defects have been used. The permissible value of primary to secondary leak rate was evaluated with respect to permissible axial through-wall defect size of WWER 440 and 1000 steam generator tubes. Blocking of the tube cracks by corrosion product particles and other compounds reduces the primary to secondary leak rate. The plugging limits involve the following factors: permissible tube wall thickness which determine further operation of the tubes with defects and assures their integrity under operating conditions and permissible size of a through-wall crack which is sufficiently stable under normal and accident conditions in relation to the critical crack length. For the evaluation of burst test of heat exchange tubes with longitudinal through-wall defects the instability criterion has been used and the dependence of the normalised burst pressure on the normalised length of an axial through-wall defect has been determined. The validity of the criterion of instability for WWER tubes with through

Armenian earthquake WWER-440 NNPs and Turkish early warning system

International Nuclear Information System (INIS)

Bektur, Y.

1991-01-01

On December 7, 1988 a severe earthquake occurred at Spitak, approximately 90-100 km far from the Armenian Nuclear Power Plant in Yerivan. Another one named Vrancea earthquake which occurred on 4 March, 1977. During this earthquake, the Kozloduj NPP (Bulgaria) was strongly damaged. Until this event, seismic loadings had received scant attention in the siting of WWER's. However after the Kozlodui damage Soviet designers changed their opinion. In this study, the seismicity of the Black Sea region and eastern Europe, seismic requirements for WWER's and the changes in plants for which to resistant against to the earthquake are given. During the earthquake radiation levels obtained by Turkish early warning system is also given

Code package to analyse behavior of the WWER fuel rods in normal operation: TOPRA's code

International Nuclear Information System (INIS)

Scheglov, A.; Proselkov, V.

2001-01-01

This paper briefly describes the code package intended for analysis of WWER fuel rod characteristics. The package includes two computer codes: TOPRA-1 and TOPRA-2 for full-scale fuel rod analyses; MRZ and MKK codes for analyzing the separate sections of fuel rods in r-z and r-j geometry. The TOPRA's codes are developed on the base of PIN-mod2 version and verified against experimental results obtained in MR, MIR and Halden research reactors (in the framework of SOFIT, FGR-2 and FUMEX experimental programs). Comparative analysis of calculation results and results from post-reactor examination of the WWER-440 and WWER-1000 fuel rod are also made as additional verification of these codes. To avoid the enlarging of uncertainties in fuel behavior prediction as a result of simplifying of the fuel geometry, MKK and MRZ codes are developed on the basis of the finite element method with use of the three nodal finite elements. Results obtained in the course of the code verification indicate the possibility for application of the method and TOPRA's code for simplified engineering calculations of WWER fuel rods thermal-physical parameters. An analysis of maximum relative errors for predicting of the fuel rod characteristics in the range of the accepted parameter values is also presented in the paper

Fuel assembly leak tightness control on WWER-1000 reactor

International Nuclear Information System (INIS)

Ivanova, R.; Gerchev, N.; Mateev, A.

2001-01-01

The main index for integrity of the fuel rods cladding is the specific activity value of the primary coolant. This value determines the safe operation of the reactor. The limit for safe operation of WWER-1000 reactor is the value of the total activity of Iodine isotopes in the primary coolant 5.0x10 -3 Ci/l. The paper briefly describes the methodology for performing a fuel tightness test (sipping test) and shows the results from these tests performed during the period 1987 -1999 in units 5 and 6 at the Kozloduy NPP. An additional index related to the safe operation is defined to characterize the fuel cladding integrity Fuel Reliability Index (FRI). The FRI is defined as value of the average activity of 131 I in the primary coolant, corrected with a part of precipitated 235 U migration and fixed to the general permanent purification frequency. Two criteria (quantitative and statistic) are determined to qualify the fuel cladding integrity. The results from sipping tests show good reliability of the fuel irradiated in unit 5 and 6 at the Kozloduy NPP

Nuclear power development

International Nuclear Information System (INIS)

Povolny, M.

1980-01-01

The development and uses of nuclear power in Czechoslovakia and other countries are briefly outlined. In the first stage, the Czechoslovak nuclear programme was oriented to the WWER 440 type reactor while the second stage of the nuclear power plant construction is oriented to the WWER 10O0 type reactor. It is envisaged that 12 WWER 440 type reactors and four to five WWER 1000 type reactors will be commissioned till 1990. (J.P.)

Present status of the physical-neutronic calculation system for nuclear fuel management at the Juragua Power Plant WWER-440 reactors

International Nuclear Information System (INIS)

Garcia H, Carlos R.; Milian, Daniel

1997-01-01

In this paper the most remarkable results obtained in Cuba, for the Juragua Nuclear Power Plant (JNPP) in core fuel management, are shown. The main characteristic of the codes used to solve the usual sequence of neutron-physical calculations available in our code library are reported. The codes validation was based on estimative of their accuracy by inter comparing calculated and WWER-440 NPP's operation data. A brief summary of the extensive calculations carried out for the JNPP Preliminary Safety Report elaboration is presented. This report is one of the requisites demanded by the Cuban Nuclear Agency for issuing the General Permission for restart works in the plant. (author). 12 refs., 4 figs., 6 tabs

Evaluation of the PTS potential in a WWER-1000 following a steam line break

International Nuclear Information System (INIS)

Beghini, M.; D'Auria, F.; Galassi, G.M.; Vitale, E.

1997-01-01

A qualified nodalization for WWER-1000 is available at DCMN (Dipartimento di Costruzioni Meccaniche e Nucleari) of University of Pisa that is suitable for running with the thermohydraulic system code Relap5/mod3.2. The nodalization consists of about 1400 hydraulic nodes and more than 5000 mesh points for conduction heat transfer. The four loops of the NPP are separately modelled. Detailed information about the plant hardware has been gotten from contacts with Eastern Organizations in Bulgaria, Russia and Ukraine. The qualification of the nodalization has been achieved at a steady state level utilizing a procedure available at DCMN and at a transient level on the basis of operational (planned) transients performed in the Bulgarian Kozloduy-5 NPP and of the unplanned transient occurred at the Ukrainian Zaporosche NPP (April 1995). Data measured in steam generators have also been utilized. The nodalization has been widely applied to the analysis of accident scenarios in WWER-1000, including Large Break LOCA, Small Break LOCA, ATWS, Loss of Feedwater and Station Blackout. The present activity aims at evaluating the potential for PTS (Pressurized Thermal Shock) following a steam line break accident. The thermalhydraulic results were employed as input for a parametric Fracture Mechanics analysis based on conservative hypothesis of the shape and localization of a pre-existing defect. Stress analysis evidenced the effect of partial cooling of the vessel and gave some general indications of the risk for unstable crack propagation under the simulated PTS conditions. (author). 30 refs, 17 figs, 4 tabs

Evaluation of the PTS potential in a WWER-1000 following a steam line break

Energy Technology Data Exchange (ETDEWEB)

Beghini, M; D` Auria, F; Galassi, G M; Vitale, E [Universita degli Studi di Pisa, Dipt. di Costruzioni Meccaniche e Nucleari, Pisa (Italy)

1997-09-01

A qualified nodalization for WWER-1000 is available at DCMN (Dipartimento di Costruzioni Meccaniche e Nucleari) of University of Pisa that is suitable for running with the thermohydraulic system code Relap5/mod3.2. The nodalization consists of about 1400 hydraulic nodes and more than 5000 mesh points for conduction heat transfer. The four loops of the NPP are separately modelled. Detailed information about the plant hardware has been gotten from contacts with Eastern Organizations in Bulgaria, Russia and Ukraine. The qualification of the nodalization has been achieved at a steady state level utilizing a procedure available at DCMN and at a transient level on the basis of operational (planned) transients performed in the Bulgarian Kozloduy-5 NPP and of the unplanned transient occurred at the Ukrainian Zaporosche NPP (April 1995). Data measured in steam generators have also been utilized. The nodalization has been widely applied to the analysis of accident scenarios in WWER-1000, including Large Break LOCA, Small Break LOCA, ATWS, Loss of Feedwater and Station Blackout. The present activity aims at evaluating the potential for PTS (Pressurized Thermal Shock) following a steam line break accident. The thermalhydraulic results were employed as input for a parametric Fracture Mechanics analysis based on conservative hypothesis of the shape and localization of a pre-existing defect. Stress analysis evidenced the effect of partial cooling of the vessel and gave some general indications of the risk for unstable crack propagation under the simulated PTS conditions. (author). 30 refs, 17 figs, 4 tabs.

Experimental verification of lifetime of bolting joints for WWER reactor pressure vessels

International Nuclear Information System (INIS)

Brumovsky, M.; Polachova, H.

1992-01-01

This paper presents results from experimental verification of cyclic lifetime of bolting joints of M 140x6 mm type used for WWER-440 MW reactor pressure vessels. Bolting joints or real dimensions were tested in a special testing equipment ZS 1000 in Skoda Concern. Stud bolts are made from 25Kh1MF or 38KhN3MFA type of steels. Tests were carried out at operating as well as at room temperatures with coefficient of asymmetry equal to 0.1; one tests was realized with given bending moment. Experimental results have been compared with calculated lifetimes according to ASME, Soviet and CMEA Codes. In all cases calculations give conservative assessments. (orig.)

Calculated and experimental research of WWER-1000 assembly vibration and fretting damage

International Nuclear Information System (INIS)

Drozdov, Y.; Afanasyev, A.; Makarov, V.; Tutnov, A.; Tutnov, A.; Alekseev, E.

2008-01-01

The report covers the methods and results of the latest analytical and experimental studies of fretting corrosion and natural vibrations of a WWER-1000 reactor fuel assemblies (FA). The process of fretting-corrosion was investigated using a multi-specimen facility that simulated fragments of fuel rod-to-spacer grid and lower support grid mating units. A computational model was developed for vibrations in the mechanical system of a fuel rod fragment and a spacer grid fragment. A calculational and experimental modal analysis of a FA was performed. Natural frequencies, modes and decrements of FA vibrations were determined and a satisfactory coincidence of analytical and experimental results was obtained. The assessment of fretting-corrosion process dynamics was made and its dependences on operational factors were obtained. (authors)

WWER in-core fuel management benchmark definition

International Nuclear Information System (INIS)

Apostolov, T.; Alekova, G.; Prodanova, R.; Petrova, T.; Ivanov, K.

1994-01-01

Two benchmark problems for WWER-440, including design parameters, operating conditions and measured quantities are discussed in this paper. Some benchmark results for infinitive multiplication factor -K eff , natural boron concentration - C β and relative power distribution - K q obtained by use of the code package are represented. (authors). 5 refs., 3 tabs

Measuring neutron flux density in near-vessel space of a commercial WWER-1000 reactor

International Nuclear Information System (INIS)

Borodkin, G.I.; Eremin, A.N.; Lomakin, S.S.; Morozov, A.G.

1987-01-01

Distribution of neutron flux density in two experimental channels on the reactor vessel external surface and in ionization chamber channel of a commercial WWER-1000 reactor, is measured by the activation detector technique. Azimuthal distributions of fast and thermal neutron fluxes and height distributions of fast neutron flux density within energy range >1.2 and 2.3 MeV are obtained. Conclusion is made, that reactor core state and its structural peculiarities in the measurement range essentially affect space and energy distribution of neutron field near the vessel. It should be taken into account when determining permissible neutron fluence for the reactor vessel

Structural response of Paks NPP WWER-440 MW main building complex to blast input motion. Final report

International Nuclear Information System (INIS)

1999-01-01

The Soviet standard design units WWER-440/213 type installed in Paks NPP were not originally designed for a Safe Shutdown Earthquake. At the time of selection of Paks site on the basis of historical earthquake data was supposed that the maximum earthquake is of grade V according MSK-64 scale. This seismicity level had not required any special measures to account for seismic event effects on the Main Building Complex Structure. Current site seismicity studies reveal that the seismic hazard for the site significantly exceeds the originally estimated. In addition the safety rules and seismic code requirements became more rugged. As a part of the activities to increase the seismic safety of the Paks NPP the study on dynamic behaviour of the Main Building Complex Structure has been performed with support of IAEA. The explosion full scale tests were carried out for determining the dynamic behaviour of the structure and for assessment of the Soil Structure Interaction (SSI) effects in the modelling and analysis procedures, used in the dynamic response analyses. The objective of the project was to evaluate the blast response of the WWER-440/213 Main Building Complex at Paks NPP, based on the data available for the soil properties, recorded free-field blast input motion, and structural design. The scope of EQE-Bulgaria study was to conduct a state-of-the-art SSI analysis with a multiple foundations supported model of the Main Building Complex to assess the structure blast response. The analysis was focused on a modelling technique that assess realistically the SSI effects on the dynamic response of a structure supported on multiple foundation instead of simplified, but more conservative techniques. The scope of research was covered splitting the study into the following steps: development of a twin units model for Main Building Complex structure; development of a Low Strain Soil Properties Model; development of SSI Parameters consisting of a Multiple Foundations System

Co-ordinated research programme on benchmark study for the seismic analysis and testing of WWER-type nuclear power plants. V. 3B. Kozloduy NPP units 5/6: Analysis/testing. Working material

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-07-01

The Co-ordinated research programme on the benchmark study for the seismic analysis and testing of WWER-type nuclear power plants was initiated subsequent to the request from representatives of Member States. The conclusions adopted at the Technical Committee Meeting on Seismic Issues related to existing nuclear power plants held in Tokyo in 1991 called for the harmonization of methods and criteria used in Member States in issues related to seismic safety. The Consulltants' Meeting which followed resulted in producing a working document for CRP. It was decided that a benchmark study is the most effective way to achieve the principal objective. Two types of WWER reactors (WWER-440/213 and WWER-1000) were selected as prototypes for the benchmark exercise to be tested on a full scale using explosions and/or vibration generators. This volume of Working material contains reports related analyses and testing of Kozloduy nuclear power plant, units 5 and 6.

Co-ordinated research programme on benchmark study for the seismic analysis and testing of WWER-type nuclear power plants. V. 3A. Kozloduy NPP units 5/6: Analysis/testing. Working material

International Nuclear Information System (INIS)

1995-01-01

The Co-ordinated research programme on the benchmark study for the seismic analysis and testing of WWER-type nuclear power plants was initiated subsequent to the request from representatives of Member States. The conclusions adopted at the Technical Committee Meeting on Seismic Issues related to existing nuclear power plants held in Tokyo in 1991 called for the harmonization of methods and criteria used in Member States in issues related to seismic safety. The Consulltants' Meeting which followed resulted in producing a working document for CRP. It was decided that a benchmark study is the most effective way to achieve the principal objective. Two types of WWER reactors (WWER-440/213 and WWER-1000) were selected as prototypes for the benchmark exercise to be tested on a full scale using explosions and/or vibration generators. This volume of Working material contains reports related analyses and testing of Kozloduy nuclear power plant, units 5 and 6

Benchmark study for the seismic analysis and testing of WWER type NPPs. Final report of a co-ordinated research project

International Nuclear Information System (INIS)

2000-10-01

This report is the final results of a five-year IAEA Coordinated Research Project (CRP) launched in 1992. The main goal was the harmonization of criteria and methods used in Member States in seismic reassessment and upgrading of existing nuclear power plants. To this aim, most of the activities have been focused on a benchmarking exercise related to a mixed numerical and experimental dynamic analysis carried out on two reference units of WWER reactors (WWER-1000 and WWER-440/213): Kozloduy NPP Units 5/6 and PAKS NPP. Twenty-four institutions from 13 countries participated in the CRP, and two other institutions from Japan contributed to the CRP informally. The objective of this TECDOC is to provide a consistent and comprehensive summary of the results of the work performed in the CRP through the preparation of a ''self-standing'' report with the general conclusion of the programme: a great deal of information from the Background Documents has been included in this report with a set of recommendations for future work in this field

Results of developing and problems of further improvements for WWER-1000 FA of alternative design

International Nuclear Information System (INIS)

Molchanov, V.L.; Panyushkin, A.K.; Zheleznyak, V.M.; Samojlov, O.B.; Kuul', V.S.; Kurylev, V.I.

2001-01-01

A new fuel assembly of alternative design (FAA) is created for a WWER-1000 reactor which is characteristic of dimensional stability on operation. The FAA includes a frame of 15 alloy Eh-110 spacer grids spot welded to 6 alloy Eh-635 angle sections. In-core tests show that the FAA is stable to form changing. It is concluded that the FAA can serve as a basis for development of promising fuel cycle with high burnups, specifically, for a 4 year cycle with the use of uranium-gadolinium fuel [ru

Evolution of ASTEC V1.2 rev.1 code for WWER-1000 reactors/SBO sequence

International Nuclear Information System (INIS)

Georgieva, J.; Stefanova, A.; Groudev, P.; Tusheva, P.; Kalchev, B.; Passalacqua, R.

2006-01-01

In this paper a comparison between calculations of severe accidents occurred from WWER-1000 with ASTEC code specified for an event of full unloading with relief valves stuck opened with no hydroaccumulators intervention is presented. The purpose of the analyses provided is to present the relationship between the improvements of the actual version (ASTEC Vl.2 rev. 1) and ASTEC V1.1 p2 like: code modifications, incoming data improvements. Such discrepancies are to be examined. Case by case suggestions for ASTEC improvements are to be provided

Dynamic analysis of WWER-1000 nuclear power plants

International Nuclear Information System (INIS)

Asfura, A.P.; Jordanov, M.J.

1995-01-01

As part of the effort to assess the seismic vulnerability of nuclear power plants in Eastern Europe, a series of dynamic analyses have been carried out for several plants. These analyses were performed using modern analysis techniques, current local seismic parameters, and local soil profiles. This paper presents a compilation of some of the seismic analyses performed for the WWER-1000 reactor buildings at the nuclear power plants of Belene and Kozloduy in Bulgaria, and Temelin in the Czech Republic. The reactor buildings at these three plants are practically identical and correspond to the standard building design for this type of reactors. The series of analyses performed for these buildings encompasses various soil profiles, seismic ground motions, and different soil-structure interaction analysis techniques and modelling. The analysis of a common structure under different conditions gives the opportunity to assess the relative importance that each of the analysis elements has in the structural responses. The use of different SSI computer programs and foundation modeling was studied for Kozloduy, and the effects of different soil conditions and site-specific seismicity were studied by comparing the responses for the three plants. In-structure acceleration response spectra were selected as the structural responses for comparison purposes

WWER440 few group data library preparation and its application in MOBY-DICK modular system

International Nuclear Information System (INIS)

Krysl, V.; Mikolas, P.; Svarny, J.

2002-01-01

Paper provides summary of methodology of few-group library preparation with emphasis on new features of assemblies, like fuel assemblies with Gd burnable poison or Control Fuel Assembly with Hf plates. Special attention is devoted to the transient part (coupler) of Control Fuel Assembly from the point of view of boundary conditions preparation. Based of this methodology prepared library is implemented into macro code for different number of axial meshes for both coarse and fine mesh diffusion calculations. Problems with local power peaking calculations in WWER-440 cores are closely connected with the correct modeling of the power perturbations in the neighbourhood of Control Fuel Assembly coupler. The new version of MOBY-DICK provided with the new few group data library can assess most of effects induced by insertion of Control Fuel Assembly in the core including effects of newly designed Hf plates in the coupler of Control Fuel Assembly. Compatibility of transport and diffusion calculation was taken into account in the analysis of Control Fuel Assembly movement without/with Hf plates (Authors)

Numerical analysis of coolant mixing in the pressure vessel of WWER-440 type nuclear reactors

International Nuclear Information System (INIS)

Boros, I.; Aszodi, A.

2003-01-01

The precise description of the coolant mixing processes taking place in the reactor pressure vessel (RPV) of pressurized water nuclear reactors has an essential importance during power operation, as well as in case of incidental or accidental conditions. In this paper the detailed CFD model of the pressure vessel of a WWER-440 type reactor and calculations performed with this RPV model are presented. The CFD model of the pressure vessel contains all the important internal structural elements of the RPV. Sensitivity study on the effect of these elements was also carried out. Both steady-state and transient calculation were performed using the CFD code CFX-5.5.1. The results of the steady-state calculations give the so called mixing factors, i.e. the effect of each single primary loop at the core inlet. The mixing factors can be given for nominal circumstances (i.e. all main coolant pumps are working) or in case of less than six working MCPs. In order to validate the model the calculated mixing factors are compared with the values measured in the Paks NPP (Authors)

Calculation of isotope burn-up and change in efficiency of absorbing elements of WWER-1000 control and protection system during burn-up

International Nuclear Information System (INIS)

Timofeeva, O.A.; Kurakin, K.U.

2006-01-01

The report deals with fast and thermal neutron flows distribution in structural elements of WWER-1000 fuel assembly and absorbing rods, determination of absorbing isotope burn-up and worth variation in WWER reactor control and protection system rods. Simulation of absorber rod burn-up is provided using code package SAPPHIRE 9 5 end RC W WER allowing detailed description of the core segment spatial model. Maximum burn-up of absorbing rods and respective worth variation of control and protection system rods is determined on the basis of a number of calculations considering known characteristics of fuel cycles (Authors)

Guidance for the application of the leak before break concept. Report of the IAEA extrabudgetary programme on the safety of WWER-440 model 230 nuclear power plants

International Nuclear Information System (INIS)

1994-11-01

This document provides additional guidance on application of the LBB concept to WWER-440/230 NPPs and complements the IAEA-TECDOC-710. The objective of the report is to describe in detail the elements of the LBB concept, the necessary support as well as the condition to be fulfilled, and the verification programme. It should also provide a clear picture of all the activities and resources needed to implement the LBB successfully as a comprehensive concept

The database 'EDUD Base' for validation of neutron-physics codes used to analyze the WWER-440 cores

International Nuclear Information System (INIS)

Rocek, J.; Belac, J.; Miasnikov, A.

2003-01-01

The program and data system EDUDBase for validation of reactor computing codes was developed at NRI. It is designed for validation and evaluation of the precision of different computer codes used for WWER core analyses. The main goal of this database is to provide data for comparison with calculation results of tested codes and tools for statistical analysis or differences between the calculation results and the test data. The benchmark data sets are based on in-core measurements performed on WWER-440 reactors of Dukovany NPP. The initial data from NPP are verified, errors and inaccuracies are eliminated and data are transferred to a form, which is suitable for comparison with results of calculations. A special reduced operating history data set is created for each operating cycle ('Benchmark Operation History') to be used as an input data for calculation. It contains values of some integral quantities for each time point: effective time, integral thermal power, boron concentration, position of working group control assemblies (group 6) and inlet coolant temperature. At present, sets are available for all completed cycles up to: (unit/cycle) 1/17, 2/16, 3/15, 4/15. Power distribution is described for approx. 40 time steps during each operating cycle. 2D-power distributions are transferred into 60-degree core symmetry sector of reactor core. At present, such data sets are available only for later cycles starting with: (unit/cycle) 1/7, 2/6, 3/5, 4/5 (in other words last II cycles for each unit) (Authors)

Results of noise analysis in the WWER 440 - type nuclear power plant Dukovany

International Nuclear Information System (INIS)

Runkel, J.; Stegemann, D.; Fiedler, J.; Hrosso, P.; Figedy, S.; Sadilek, J.; Hulin, J.

1996-01-01

Results of a common work in the frame of scientific and technological cooperation between the Slovak Republic and Germany in the field of development of diagnostic methods to improve the safety and availability of WWER-type reactors are presented. Signals of the standard diagnostic instrumentation of the WWER-type reactors of units 1,2 and 4 at the nuclear power plant Dukovany (EDU) in Czech Republic were analyzed. Mechanical vibrations like pendular and vertical movements of the reactor pressure vessel and its internals as well as thermohydraulic fluctuations like fluid resonances or standing pressure waves could be identified in all the three units. Incipient changes of the mechanical and/or thermohydraulic conditions of the core can be detected by periodical analysis of the signals of the standard reactor instrumentation of WWER-types reactors. (authors)

The decommissioning of WWER type nuclear power plants. Final report on an IAEA regional technical co-operation project

International Nuclear Information System (INIS)

2000-01-01

Numerous WWER-440 nuclear power plants are in operation in central and eastern Europe and a small number have already been shut down. In addition to reactors already shut down, many other reactors will reach the end of their design lifetime in a few years and become candidates for decommissioning. It is unfortunate that little consideration was devoted to decommissioning of WWER-440 reactors at the plant design and construction stage, and little emphasis was placed on planning for decommissioning. It is within this context that the IAEA launched a regional technical co-operation project in 1994 with the aim of providing guidance on planning and management of decommissioning for WWERs. The project, which had a duration of four years (1995-1998), included the organization of workshops and scientific visits to countries having WWERs and other countries where active decommissioning projects were under way. Eventually, participants suggested the consolidation of expert guidance and collective opinions into a TECDOC, which was drafted by both designated participants from project recipient countries and invited experts. The TECDOC has the aim of serving as a stimulus for all concerned parties in central and eastern European countries to initiate concrete decommissioning planning, including assessment of existing and required resources for the eventual implementation of decommissioning plans. In addition, the regional technical co-operation project has managed to bring together in this TECDOC a number of good practices that could be useful in WWER-440 decommissioning

Probabilistic safety analysis of the Kozloduy NPP units 1-4 (WWER-440/230) using independent emergency feedwater system; Veroyatnostnyj analiz bezopasnosti I-IV blokov AEhS `Kozloduy` s reaktorami tipa WWER-440 (V 230) pri vklyuchenii nezavisimoj sistemy avarijnoj podpitki PG

Energy Technology Data Exchange (ETDEWEB)

Kalchev, B; Marinov, M; Dimitrov, B; Avdzhiev, K [Energoproekt, Sofia (Bulgaria)

1996-12-31

The safety of the Kozloduy NPP is being promoted by backfitting and improved operational practice. Special measures mitigating potential severe accidents consequences are needed because of some deficiencies in the original design of the four WWER-440 units. In conditions of a total LOCA (Loss Of Coolant Accident) it is impossible to ensure decay heat removal using the existing safety system. In such cases an extra emergency feedwater system independent of the plant`s other systems has been introduced which offers a new alternative means of removing the residual heat from the reactor. A probabilistic safety analysis is carried out using the method of event trees. A comparison between the existing safety system and the newly proposed is made. The simulation results of the unit behaviour prove that the damage frequency of the active zone is lower with the new system. 3 refs., 3 tabs., 2 figs.

Quantum behaved Particle Swarm Optimization with Differential Mutation operator applied to WWER-1000 in-core fuel management optimization

International Nuclear Information System (INIS)

Jamalipour, Mostafa; Sayareh, Reza; Gharib, Morteza; Khoshahval, Farrokh; Karimi, Mahmood Reza

2013-01-01

Highlights: ► A new method called QPSO-DM is applied to BNPP in-core fuel management optimization. ► It is found that QPSO-DM performs better than PSO and QPSO. ► This method provides a permissible arrangement for optimum loading pattern. - Abstract: This paper presents a new method using Quantum Particle Swarm Optimization with Differential Mutation operator (QPSO-DM) for optimizing WWER-1000 core fuel management. Genetic Algorithm (GA) and Particle Swarm Optimization (PSO) have shown good performance on in-core fuel management optimization (ICFMO). The objective of this paper is to show that QPSO-DM performs very well and is comparable to PSO and Quantum Particle Swarm Optimization (QPSO). Most of the strategies for ICFMO are based on maximizing multiplication factor (k eff ) to increase cycle length and minimizing power peaking factor (P q ) in order to improve fuel integrity. PSO, QPSO and QPSO-DM have been implemented to fulfill these requirements for the first operating cycle of WWER-1000 Bushehr Nuclear Power Plant (BNPP). The results show that QPSO-DM performs better than the others. A program has been written in MATLAB to map PSO, QPSO and QPSO-DM for loading pattern optimization. WIMS and CITATION have been used to simulate reactor core for neutronic calculations

Verification results of methodology for determining the weighted mean coolant temperature in the primary circuit hot legs of WWER-1000 reactor plants

International Nuclear Information System (INIS)

Saunin, Yuri V.; Dobrotvorski, Alexander N.; Semenikhin, Alexander V.; Korolev, Alexander S.

2017-01-01

The JSC ''Atomtechenergo'' experts have developed a new methodology for determining the weighted mean coolant temperature in the primary circuit hot legs of WWER-1000 reactor plants. The necessity for developing the new methodology was determined by the need to decrease the calculation error of the weighted mean coolant temperature in the hot legs because of the coolant temperature stratification. The methodology development was based on the findings of experimental and calculating research executed by the authors. The methodology verification was fulfilled through comparison of calculation results obtained with and without the methodology use in various operational states and modes of several WWER-1000 power units. The obtained verification results have confirmed that the use of the new methodology provides objective error decrease in determining the weighted mean coolant temperature in the primary circuit hot legs. The decrease value depends on the stratification character which is various for different objects and conditions.

Verification results of methodology for determining the weighted mean coolant temperature in the primary circuit hot legs of WWER-1000 reactor plants

Energy Technology Data Exchange (ETDEWEB)

Saunin, Yuri V.; Dobrotvorski, Alexander N.; Semenikhin, Alexander V.; Korolev, Alexander S. [JSC ' ' Atomtechenergo' ' , Novovoronezh (Russian Federation). Novovoronezh Filial ' ' Novovoronezhatomtechenergo' ' ; Ryasny, Sergei I. [JSC ' ' Atomtechenergo' ' , Moscow (Russian Federation)

2017-09-15

The JSC ''Atomtechenergo'' experts have developed a new methodology for determining the weighted mean coolant temperature in the primary circuit hot legs of WWER-1000 reactor plants. The necessity for developing the new methodology was determined by the need to decrease the calculation error of the weighted mean coolant temperature in the hot legs because of the coolant temperature stratification. The methodology development was based on the findings of experimental and calculating research executed by the authors. The methodology verification was fulfilled through comparison of calculation results obtained with and without the methodology use in various operational states and modes of several WWER-1000 power units. The obtained verification results have confirmed that the use of the new methodology provides objective error decrease in determining the weighted mean coolant temperature in the primary circuit hot legs. The decrease value depends on the stratification character which is various for different objects and conditions.

The numerical simulation of the WWER-440/V-213 reactor pressure vessel internals response to maximum hypothetical large break loss of coolant accident

International Nuclear Information System (INIS)

Hermansky, P.; Krajcovic, M.

2012-01-01

The reactor internals are designed to ensure cooling of the fuel, to ensure the movement of emergency control assemblies under all operating conditions including accidents and facilitate removal of the fuel and of the internals following an accident This paper presents results of the numerical simulation of the WWER-440/V213 reactor vessel internals dynamic response to maximum hypothetical Large-Break Loss of Coolant Accident. The purpose of this analysis is to determine the reactor vessel internals response due to rapid depressurization and to prove no such deformations occur in the reactor vessel internals which would prevent timely and proper activation of the emergency control assemblies. (Authors)

Experience of development of the methods and equipment and the prospects for creation of WWER fuel examination stands

International Nuclear Information System (INIS)

Pavlov, S.; Smirnov, V.

1998-01-01

The report presents the basic methods and equipment developed for inspection of the fuel elements and fuel assemblies in the spent fuel pools. It considers their characteristics and results of the tests under laboratory and experimental fuel examination stand conditions. In particular, the following techniques are presented: visual inspection, measurement of the geometrical dimensions, definition of the form change in fuel assemblies and fuel elements, detection of the failed fuel elements, etc. The experience of the experimental fuel examination stand operation is generalized. The concept of the creation of the WWER-440 and WWER-1000 FA and FE inspection stands is presented. The concept is based on the modular principle which runs as follows. A set of the basic functional blocks is being developed based on which it is possible to make such a stand configuration which is necessary to fulfil the specific program of the examination at the particular nuclear power plant. (author)

Experimental verification of FA for WWER-1000. Investigations of TVS - 2M

International Nuclear Information System (INIS)

Vasilchenko, I.; Seleznev, A.; Kobelev, S.; Makarov, V.; Afanasjev, A.; Matvienko, I.; Enin, A.; Ustimenko, A.; Volkov, S.

2008-01-01

During development of TVS-2M design for WWER-1000 and within the scope of its pre-reactor verification there was performed a complex of bench tests of FA for operational impacts. These tests were carried out with the use of the full-scale non-irradiated FA dummy and the models of units. The present report presents the methods and the results of tests of the full-scale dummy for static concentrated loads, impact of thermal cycling and vibration under separate and simultaneous impact of the listed loads. The results of tests carried out indicate that the solutions implemented in TVS-2M, first of all, a rigid welded skeleton, provide much higher resistance to distortion due to thermomechanical loads in comparison with zirconium AFA of the previous generation. This work was organized by JSC TVEL. (authors)

Fuel assembly outlet temperature profile influence on core by-pass flow and power distribution determination in WWER -440 reactors

International Nuclear Information System (INIS)

Petenyi, V.; Klucarova, K.; Remis, J.

2003-01-01

The in core instrumentation of the WWER-440 reactors consists of the thermocouple system and the system of self powered detectors (SPD). The thermocouple systems are positioned about 50 cm above the fuel bundle upper flow-mixing grid. The usual assumption is that, the coolant is well mixed in the Tc location, i.e. the temperature is constant through the flow cross-section area. The present evaluations by using the FLUENT 5.5.14 code reveal that, this assumption is not fulfilled. There exists a temperature profile that depends on fuel assembly geometry and on inner power profile of the fuel assembly. The paper presents the estimation of this effect and its influence on the core power distribution and the core by-pass flow determination. Comparison with measurements in Mochovce NPP will also be a part of this presentation (Authors)

Review of WWER fuel and material tests in the Halden reactor

International Nuclear Information System (INIS)

Volkov, B.; Kolstad, E.

2006-01-01

A review of the tests with WWER fuels and materials conducted in HBWR over the years of cooperation with Russia is presented. The first test with old generation WWER-440 fuel and PWR specification fuel was carried out from 1995 to 1998. Some differences between these fuels regarding irradiation induced densification and pellet design as well as similar fuel thermal behaviour, swelling and FGR were revealed during the test. The data from this test are reviewed and compared with PIE recently performed to confirm the in-pile measurements. The second test was started in March 1999 with the main objective to study different modified WWER fuels also in comparison with PWR fuel. The results indicated that all these modified WWER fuels exhibit improved densification properties relative to earlier tested fuel. In-pile data on fuel densification have been analysed with respect to as fabricated fuel microstructure and can be used for verification of fuel behaviour models. Corrosion and creep tests in the Halden reactor encompass WWER cladding alloys and some results are given. Prospective WWER fuel and material tests foreseen within the frame of the joint program of OECD HRP are also presented. (authors)

Analysis of some fuel characteristics deviations and their influence over WWER-440 fuel cycle design

International Nuclear Information System (INIS)

Stoyanova, I.; Kamenov, K.

2001-01-01

The aim of this study is to estimate the influence of some deviations in WWER-440 fuel assemblies (FA) characteristics upon fuel core design. A large number of different fresh fuel assemblies with enrichment of 3.5 t % are examined related to the enrichment, mass of initial metal Uranium and assembly shroud thickness. Infinite multiplication factor (Kinf) in fuel assembly has been calculated by HELIOS spectral code for basic assembly and for different FA with deviation of a single parameter. The effects from single parameter deviation (enrichment) and from two parameter deviations (enrichment and wall thickness) on the neutron-physics characteristics of the core are estimated for different fuel assemblies. Relatively week burnup dependence on Kinf is observed as result of deviation in the enrichment of the fuel and in the wall thickness of the assembly. An assessment of a FA single and two parameter deviations effects on design fuel cycle duration and relative power peaking factor is also considers in the paper. As a final conclusion can be settled that the maximum relative shortness of fuel cycle can be observed in the case of two FA parameters deviations

Data base and postirradiation examination results of spent WWER-1000 fuel elements and assemblies

International Nuclear Information System (INIS)

Kanashov, B.A.; Polenok, V.S.; Smirnov, A.V.; Zhitelev, V.A.

1995-01-01

The report presents the results of the postirradiation shape change examination of standard fuel elements and fuel assemblies irradiated in standard conditions in Russian power reactors of the WWER-1000 type. The information is based on the results obtained at the Fuel Research Department of the Federal Scientific Centre Research Institute of Atomic Reactors (FSC RIAR, Dimitrovgrad, Russian Federation) within the period from 1987 to 1994. Emphasis is placed on such experimental and calculational data as: length, cross-section dimensions and shape of FAs with wrapper; change of standard FA skeleton members dimensions; fuel bundle elongation; change of the fuel cladding outer diameter; and elongation and change of the fuel stack outer diameter. (author)

Safety of WWER type nuclear power plants - viewing from Hungary

International Nuclear Information System (INIS)

Voeroess, L.

1991-01-01

An evaluation of WWER type nuclear power plants operating in Hungary is given, relative to the safety requirements accepted internationally; how safe can they be regarded and what can be done to assure a high level of safety in all case. After an overview of general safety criteria, an overall description of WWER-440 type nuclear reactors is presented. Design safety, operational safety issues are treated in detail. Safety inspection and safety-related research and development is discussed. Regarding the future, five different issues associated with nuclear reactor safety should be considered. (R.P.) 20 refs.; 12 figs.; 3 tabs

First generation WWER 440 - What is the 'reasonable' price?

International Nuclear Information System (INIS)

Pishtuhina, K.

2004-01-01

A chronological review of the international nuclear concerns and Three Mile Island and Chernobyl accidents effects on the international nuclear organizations' policies are presented. The IAEA, G 7 and EU approaches for Soviet design plants' safety and the main results from their implementation are described. The premature closure of the first generation WWER type reactors operated in Bulgaria, Lithuania and Slovakia and their unupgradability at a reasonable price are also discussed in this paper

Advances in new WWER designs to improve operation and maintenance

International Nuclear Information System (INIS)

Dragunov, Y.G.; Ryzhov, S.B.; Podshibiakin, A.K.; Vasilchenko, I.N.; Repin, A.I.; Nikitenko, M.P.; Konoplev, N.P.; Fil, N.S.

2000-01-01

Economic operational indices of WWER-type reactors show their competitiveness in all the countries where these reactors operate. Advanced WWERs being designed and constructed now have the improved characteristics of economical efficiency and are more convenient for operation and maintenance. Many technical solutions aimed at improvement of the operational performance are implemented in the design of WWER-1000/V-392 and WWER-640/V-407, and these reactors are the important basis for the nuclear power expansion in Russia. Some of these solutions are considered in the present paper. (author)

A new neutron spectrometry system for in-core and out-core application at WWER

International Nuclear Information System (INIS)

Mehner, H.C.; Boehmer, B.; Hagemann, U.; Nagel, S.; Schoene, M.; Stephan, I.

1985-01-01

An automated measuring system based on a newly-developed multi-component wire activation detector (MWAD) is presented which has been applied for neutron spectrometry inside WWER. The MWAD consisting of Au, Mn, Mo, Ni, and W is designed to determine the neutron spectrum in the thermal, epithermal and fast energy region by a single gamma-ray spectrum measurement. Investigations were carried out within an ordinary fuel assembly of the Greifswald NPS (WWER-440) as well as in experimental fuel assembly of the Rheinsberg NPS (WWER-70). The evaluation of the measurements was done with the newly-developed adjustment code COSA based on the generalized least square method. (author)

Examples for cost reduction in the design of a WWER-1000 nuclear power plant

International Nuclear Information System (INIS)

Kukkola, T.

1991-01-01

In a design project during recent years, a version for Finnish conditions has been and is being developed based on the Soviet WWER-1000 PWR plant with four horizontal steam generators. The plant will have a double containment. The inner containment will be a dry full pressure prestressed concrete containment with liner and the secondary containment will be made of ordinary concrete. Four train safety approach is adopted. It is supposed that the plant is to be designed according to the present Finnish safety requirements, e.g. severe reactor accidents are considered. When striving at an economic plant no compromises are made as far as safety is concerned. This paper describes possible cost reduction by redesigning the main technical equipment. (author). 1 ref

Blind pre-analysis of the main building complex WWER-1000 Kozloduy. Comparison of analytical and experimental results obtained by explosive testing (task 8a of workplan 96/97)

International Nuclear Information System (INIS)

Krutzik, N.J.

1999-01-01

In accordance with the 96/97 workplan of the Research Programme on 'Benchmark Studies for Seismic Analysis and Testing of WWER-Type Nuclear Power Plants', blind pre analyses were prepared for the main building complex of the WWER-1000 based on given excitations derived from explosive tests. The investigations were performed by several institutions based on various mathematical models and procedures for consideration of soil-structure interaction effects, but on the same explosive test input data recently obtained. The methods of calculation and software tools used will also be different. The aim of this investigation is to validate different idealization concepts (mathematical models for the idealization of the structures and the soil) as well as investigation procedures (time domain and frequency domain analysis) and finally the software tools by comparing structural response results (time histories and response spectra). This report contains the results of the blind pre analysis performed by Siemens using an equivalent beam model of the main building of the WWER 1000. The calculations were performed by means of a frequency domain calculation

Study of multiplication factor sensitivity to the spread of WWER spent fuel isotopics calculated by different codes

International Nuclear Information System (INIS)

Markova, L.

2001-01-01

As a sensitivity study the impact on the system reactivity was studied in the case that different calculational methodologies of spent fuel isotopic concentrations were used for WWER spent fuel inventory computations. The sets of isotopic concentrations obtained by calculations with different codes and libraries as a result of the CB2 international benchmark focused on WWER-440 burnup credit were used to show the spread of the calculated spent fuel system reactivity. Using the MCNP 4B code and changing the isotopics input data, the multiplication factor of an infinite array of the WWER-440 fuel pin cells was calculated. The evaluation of the results shows the sensitivity of the calculated reactivity to different calculational methodologies used for the spent fuel inventory computation. In the studied cases of the CB2 benchmark, the spread of the reference k-results relative to the mean was found less or about ±1% in spite of the fact that the data of isotopic concentrations were spread much more. (author)

Mounting of localization shaft by enlarged structures at the NPP with WWER-440

International Nuclear Information System (INIS)

Naumenko, S.V.

1982-01-01

A technique of mounting of a localization system at the WWER-440 NPP is described. The localization system consists of air-lift devices located in pressurized building (shaft) 12.6 thousand m 3 volume. Air-lift devices are placed in 12 bayers with 3.37 m spacing over the height of localization shaft. Every layer of air-lift devices consists of 18 supporting H-beams number 60 of 8.5 m in length. The total host of air-lift devices and metal works of servicing platforms is equal to 725 t. The air-lift device consists of the large number of details (660 pieces of 500-2500 kg mass and above 2500 pieces of 500 kg mass), which causes the necessity of accomplishing a large volume of assembling and welding works. To reduce the labour content in the mounting zone and volume of work accomplished at the height the method of large-structure mounting of air-lift devices was suggested. The method lies in ground assembly of air-lift structures on the basis of several supporting beams and their following lifting to the corresponding layer. The large-structure mounting of localization shaft enables to reduce by 25-30% the length of joint welds made during the mounting as well as the volume of transport and cordage works; to reduce the time of building crane usage and 1.5-1.7 times the total periods of works

The further development of WWER-440 fuel design performance

International Nuclear Information System (INIS)

Lushin, V.; Vasilchenko, I.; Ananjev, J.; Abashina, G.

2011-01-01

The most distinguished stages in VVER-440 fuel development of the latest ten years are: designing of second generation FA complex; and designing of sheathless working fuel assembly of the third generation (RK-3) which are presented in this report. Designing of fuel assemblies of the second generation and RK-3 is characterized by the tendency to power increase of VVER-440 operating units with V-213-type reactor, that, in turn, has given a stimulus to further design enhancement of fuel assemblies specified. The further development of the second generation fuel assembly design and the change-over to the third generation working assemblies will allow for fuel utilization to be considerably increased under the conditions of application the more long-term fuel cycles for VVER-440 reactors and operation of the Units at the increased power

Post-test investigation result on the WWER-1000 fuel tested under severe accident conditions

International Nuclear Information System (INIS)

Goryachev, A.; Shtuckert, Yu.; Zwir, E.; Stupina, L.

1996-01-01

The model bundle of WWER-type were tested under SFD condition in the out-of-pile CORA installation. The objective of the test was to provide an information on the WWER-type fuel bundles behaviour under severe fuel damage accident conditions. Also it was assumed to compare the WWER-type bundle damage mechanisms with these experienced in the PWR-type bundle tests with aim to confirm a possibility to use the various code systems, worked our for PWR as applied to WWER. In order to ensure the possibility of the comparison of the calculated core degradation parameters with the real state of the tested bundle, some parameters have been measured on the bundle cross-sections under examination. Quantitative parameters of the bundle degradation have been evaluated by digital image processing of the bundle cross-sections. The obtained results are shown together with corresponding results obtained by the other participants of this investigation. (author). 3 refs, 13 figs

A simplified approach to WWER-440 fuel assembly head benchmark

International Nuclear Information System (INIS)

Muehlbauer, P.

2010-01-01

The WWER-440 fuel assembly head benchmark was simulated with FLUENT 12 code as a first step of validation of the code for nuclear reactor safety analyses. Results of the benchmark together with comparison of results provided by other participants and results of measurement will be presented in another paper by benchmark organisers. This presentation is therefore focused on our approach to this simulation as illustrated on the case 323-34, which represents a peripheral assembly with five neighbours. All steps of the simulation and some lessons learned are described. Geometry of the computational region supplied as STEP file by organizers of the benchmark was first separated into two parts (inlet part with spacer grid, and the rest of assembly head) in order to keep the size of the computational mesh manageable with regard to the hardware available (HP Z800 workstation with Intel Zeon four-core CPU 3.2 GHz, 32 GB of RAM) and then further modified at places where shape of the geometry would probably lead to highly distorted cells. Both parts of the geometry were connected via boundary profile file generated at cross section, where effect of grid spacers is still felt but the effect of out flow boundary condition used in the computations of the inlet part of geometry is negligible. Computation proceeded in several steps: start with basic mesh, standard k-ε model of turbulence with standard wall functions and first order upwind numerical schemes; after convergence (scaled residuals lower than 10-3) and near-wall meshes local adaptation when needed, realizable k-ε of turbulence was used with second order upwind numerical schemes for momentum and energy equations. During iterations, area-average temperature of thermocouples and area-averaged outlet temperature which are the main figures of merit of the benchmark were also monitored. In this 'blind' phase of the benchmark, effect of spacers was neglected. After results of measurements are available, standard validation

Comparative analysis of exercise 2 results of the OECD WWER-1000 MSLB benchmark

International Nuclear Information System (INIS)

Kolev, N.; Petrov, N.; Royer, E.; Ivanov, B.; Ivanov, K.

2006-01-01

In the framework of joint effort between OECD/NEA, US DOE and CEA France a coupled three-dimensional (3D) thermal-hydraulic/neutron kinetics benchmark for WWER-1000 was defined. Phase 2 of this benchmark is labeled W1000CT-2 and consists of calculation of a vessel mixing experiment and main steam line break (MSLB) transients. The reference plant is Kozloduy-6 in Bulgaria. Plant data are available for code validation consisting of one experiment of pump start-up (W1000CT-1) and one experiment of steam generator isolation (W1000CT-2). The validated codes can be used to calculate asymmetric MSLB transients involving similar mixing patterns. This paper summarizes a comparison of the available results for W1000CT-2 Exercise 2 devoted to core-vessel calculation with imposed MSLB vessel boundary conditions. Because of the recent re-calculation of the cross-section libraries, core physics results from PARCS and CRONOS codes could be compared only. The comparison is code-to-code (including BIPR7A/TVS-M lib) and code vs. plant measured data in a steady state close to the MSLB initial state. The results provide a test of the cross-section libraries and show a good agreement of plant measured and computed data. The comparison of full vessel calculations was made from the point of view of vessel mixing, considering mainly the coarse-mesh features of the flow. The FZR and INRNE results from multi-1D calculations with different mixing models are similar, while the FZK calculations with a coarse-3D vessel model show deviations from the others. These deviations seem to be due to an error in the use of a boundary condition after flow reversal (Authors)

Status and trends in nuclear technology for power plants with WWER-1000 reactors. Review

Energy Technology Data Exchange (ETDEWEB)

Zorev, N N

1977-04-01

The problems of improving quality of nuclear equipment for WWER-1000 power plants and associated nuclear technology automation are surveyed. Examples of technological innovations are presented which significantly reduce labour intensity, time consumption and increase quality standards of the products. Some new automated equipments for materials welding, working, machining and quality control are described. The discussion is centering around heavy-section steel technologies. Some mechanical properties of new-developed nuclear grade steels designed for producing reactor vessels and steamgenerators, volume compensators and pipes, as well as steam separators and steamsuperheaters are also presented. Their properties (impact strength and radiation resistance) are pointed out to be superior to that of steels used abroad. The basic trend in nuclear structural material developments is towards integrated optimization of strength, performance and workability.

Criticality calculations of various spent fuel casks - possibilities for burn up credit implementation

International Nuclear Information System (INIS)

Apostolov, T; Manolova, M.; Prodanova, R.

2001-01-01

A methodology for criticality safety analysis of spent fuel casks with possibilities for burnup credit implementation is presented. This methodology includes the world well-known and applied program systems: NESSEL-NUKO for depletion and SCALE-4.4 for criticality calculations. The abilities of this methodology to analyze storage and transportation casks with different type of spent fuel are demonstrated on the base of various tests. The depletion calculations have been carried out for the power reactors (WWER-440 and WWER-1000) and the research reactor IRT-2000 (C-36) fuel assemblies. The criticality calculation models have been developed on the basis of real fuel casks, designed by the leading international companies (for WWER-440 and WWER-1000 spent fuel assemblies), as well as for real a WWER-440 storage cask, applied at the 'Kozloduy' NPP. The results obtained show that the criticality safety criterion K eff less than 0.95 is satisfied for both: fresh and spent fuel. Besides the implementation of burnup credit allows to account for the reduced reactivity of spent fuel and to evaluate the conservatism of the fresh fuel assumption. (author)

National Report of Bulgaria [National practice at WWER sites

International Nuclear Information System (INIS)

2017-01-01

Kozloduy NPP Plc. is located in north-western Bulgaria at about 3 km from the Danube River, which serves as a source of cooling water and a receiver of liquid released from the plant (Fig. I.3). Six nuclear units were constructed on Kozloduy NPP site. Units 1 to 4 are WWER-440/230 reactors and Units 5 and 6 are WWER-1000/320 reactors. Units 1 to 4 were commissioned from 1974 to 1982. Units 5 and 6 were commissioned in 1987 and 1991, respectively. On December 31, 2002 Units 1 and 2 were shut down and on December 31, 2006 Units 3 and 4 were shut down as well. Spent Nuclear Fuel was removed from the pre-reactor pools and the reactors have been prepared for decommissioning. Units 1 and 2 (in 2008) and Units 3 and 4 (in 2012) were declared as Decommissioning Facilities by Ministerial Decree and outsourced from the plant. A separate complex consisting of facilities for treatment and conditioning of wet and dry solid radioactive waste (RAW) and a facility for storage of conditioned RAW was commissioned in 2001 on site. The complex is situated next to the Auxiliary Building of Units 5 and 6. In 2005 this complex was outsourced as a separate enterprise called the Specialized Enterprise for Radioactive Waste (SE RAW). There are two Spent Fuel Storage Facilities (SFSF) for wet and dry storage located on the plant site as well.

Seismic Probabilistic Risk Assessment (SPRA), approach and results

International Nuclear Information System (INIS)

Campbell, R.D.

1995-01-01

During the past 15 years there have been over 30 Seismic Probabilistic Risk Assessments (SPRAs) and Seismic Probabilistic Safety Assessments (SPSAs) conducted of Western Nuclear Power Plants, principally of US design. In this paper PRA and PSA are used interchangeably as the overall process is essentially the same. Some similar assessments have been done for reactors in Taiwan, Korea, Japan, Switzerland and Slovenia. These plants were also principally US supplied or built under US license. Since the restructuring of the governments in former Soviet Bloc countries, there has been grave concern regarding the safety of the reactors in these countries. To date there has been considerable activity in conducting partial seismic upgrades but the overall quantification of risk has not been pursued to the depth that it has in Western countries. This paper summarizes the methodology for Seismic PRA/PSA and compares results of two partially completed and two completed PRAs of soviet designed reactors to results from earlier PRAs on US Reactors. A WWER 440 and a WWER 1000 located in low seismic activity regions have completed PRAs and results show the seismic risk to be very low for both designs. For more active regions, partially completed PRAs of a WWER 440 and WWER 1000 located at the same site show the WWER 440 to have much greater seismic risk than the WWER 1000 plant. The seismic risk from the 1000 MW plant compares with the high end of seismic risk for earlier seismic PRAs in the US. Just as for most US plants, the seismic risk appears to be less than the risk from internal events if risk is measured is terms of mean core damage frequency. However, due to the lack of containment for the earlier WWER 440s, the risk to the public may be significantly greater due to the more probable scenario of an early release. The studies reported have not taken the accident sequences beyond the stage of core damage hence the public heath risk ratios are speculative. (author)

Safety problems of nuclear power plants with reactors of new generation; Voprosy bezopasnosti v proehktakh AEhS novogo pokoleniya s WWER

Energy Technology Data Exchange (ETDEWEB)

Fedorov, V; Rogov, M; Biryukov, G [Opytno-Konstruktorskoe Byuro Gidropress, Podol` sk (Russian Federation)

1996-12-31

Modernization schemes for safety enhancement of WWER-1000 reactors are proposed. In the case of WWER-1000/V-392 it is based on introduction of additional safety systems and overall design improvement. For WWER-1100 (1000-1100 MW) the safety is enhanced by passive systems built from two-stage heat exchangers. For WWER-500/600 the use of passive safety system is extended to emergency cooling of the active zone and removal of the residual heat emissions from the reactor. The technical characteristics of the three reactors are compared. 3 figs., 1 tab.

WWER radial reflector modeling by diffusion codes

International Nuclear Information System (INIS)

Petkov, P. T.; Mittag, S.

2005-01-01

The two commonly used approaches to describe the WWER radial reflectors in diffusion codes, by albedo on the core-reflector boundary and by a ring of diffusive assembly size nodes, are discussed. The advantages and disadvantages of the first approach are presented first, then the Koebke's equivalence theory is outlined and its implementation for the WWER radial reflectors is discussed. Results for the WWER-1000 reactor are presented. Then the boundary conditions on the outer reflector boundary are discussed. The possibility to divide the library into fuel assembly and reflector parts and to generate each library by a separate code package is discussed. Finally, the homogenization errors for rodded assemblies are presented and discussed (Author)

Upgrading of WWER-1000 NPP safety on spent fuel transportation

International Nuclear Information System (INIS)

Kostarev, V.; Shchukin, A.; Petrenya, Yu.; Nikitin, V.; Romanovskij-Romanko, A.; Shevchenko, V.

2003-01-01

Transportation process for the WWER-1000 spent fuel assemblies consists of three main steps: (i) lifting of unloaded cask on the elevation of +38.05 m; (ii) loading of spent fuel assemblies into the cask; (iii) loaded cask lowering to the conveyer located in the transport corridor on the elevation 0.00 m. The most hazardous situation within described process for the cask itself and reactor building structures is an accidental drop of the cask from the height of 38.05 m to the transport corridor floor due to failure of traverse or crane's cable break. According to international practice and standards' requirements the cask shall be designed for the drop from 9 meters height to a rigid plate. However, preliminary analyses have shown that in case of 38 m drop the value of g-loads are several times larger than allowable limits. Additionally, strength capacity of the foundation slab of the reactor building is not guaranteed. Using of special damping device that is capable to bring dynamic loads to allowable limits could mitigate the catastrophic consequences of cask's 38.05 meters drop. The paper presents a basic design of the special damping platform and discusses results of analyses of different modes of cask drops and efficiency of the proposed solution. (author)

Anticipated transients without scram for WWER reactors. A publication of the extrabudgetary programme on the safety of WWER and RBMK nuclear power plants

International Nuclear Information System (INIS)

1999-12-01

show that the ATWS could contribute essentially to the probability of core damage or to off-site radioactive releases (Russia) or in cases where there is only one fast acting shutdown system for which the Regulatory Authority stipulates that failure must be assumed. The development of a national policy on the ATWS issue in line with international practices is recommended for national regulatory authorities. This policy should consider the systems necessary to mitigate consequences and/or requirements for acceptable plant performance in an ATWS event. This publication provides guidance on the performance of ATWS analyses of transients for licensing purposes, on the initiating events identified for those WWER reactors, and on the best estimate approach to the transient analysis of ATWS events. Further guidance is directed at reliability assessment of instrumentation and control (I and C) related to ATWS, including its common mode failure potential, and the qualification of systems and components necessary for operation under accident conditions to mitigate ATWS. While focusing on WWER-1000 reactors, this publication also provides guidance for ATWS events in WWER-440 reactors, taking into consideration the differences of this reactor type and its instrumentation and control

A study of the pressure vessel steel of the WWER-440 unit 1 of the Kozloduy nuclear power plant

Science.gov (United States)

Kostadinova, E.; Velinov, N.; Avdjieva, T.; Mitov, I.; Rusanov, V.

2017-11-01

A comparison between highly neutron irradiated samples from the region of weld № 4 and low irradiated samples from weld № 1 taken from the pressure vessel of the WWER-440 Unit № 1 of the Kozloduy NPP has been performed. Measurements of the residual activity of samples from the outer surface of the reactor pressure vessel bottom corpus reveal very low activity of 60Co. Insofar as there the base and weld metal appear to be exposed to a very low neutron fluence, the samples from these locations can be considered as practically not affected and may serve as a reference basis for comparison with highly irradiated pressure vessel regions. The Mössbauer parameters isomer shift (IS) and quadrupole splitting (QS) were found to be absolutely irradiation insensitive. A stepwise reduction of the internal hyperfine magnetic field Bhf, each by about 2.6 T, was observed. This can be attributed to the replacement of one or two surrounding iron atoms as first nearest neighbors by non-iron alloying atoms. The Mössbauer experimental line widths for irradiated and non-irradiated samples are practically the same, which is a quite unexpected result. The area fraction ratio for the three main Zeeman sextet subspectra S1:S2:S3 shows very high irradiation sensitivity. For the bottom low irradiated region of the reactor vessel the values are S1:S2:S3 = 50.1:40.0:9.4. After seven years of operation between the pressure vessel annealing in 1989 and the autumn of 1996 when the samples from weld № 4 were taken the ratio changes strongly to S1:S2:S3 = 56.4:34.7:8.5. A possible explanation of this result is that neutron irradiation gives rise to a precipitation process involving predominantly alloying atoms as Ni, Mn, Cr, Mo and V which become mobile and precipitate in the form of carbides and/or P-rich phases and alloying atom aggregates. This "refinement" process lowers the partial area of subspectra S2 and S3 where alloying atoms are involved and leads to a higher area fraction of

Experience with the WIMS computer code at Skoda Plzen

International Nuclear Information System (INIS)

Vacek, J.; Mikolas, P.

1991-01-01

Validation of the program for neutronics analysis is described. Computational results are compared with results of experiments on critical assemblies and with results of other codes for different types of lattices. Included are the results for lattices containing Gd as burnable absorber. With minor exceptions, the results of benchmarking were quite satisfactory and justified the inclusion of WIMS in the production system of codes for WWER analysis. The first practical application was the adjustment of the WWER-440 few-group diffusion constants library of the three-dimensional diffusion code MOBY-DICK, which led to a remarkable improvement of results for operational states. Then a new library for the analysis of WWER-440 start-up was generated and tested and at present a new library for the analysis of WWER-440 operational states is being tested. Preparation of the library for WWER-1000 is in progress. (author). 19 refs

Nuclear power project planning and implementation

International Nuclear Information System (INIS)

Roumiantsev, A.N.

1976-01-01

General description of NVRs. Development of NVR technology. Basic peculiarities of NVR: technological scheme, cooling circuits, core design, initial load of core, core discharging, control and safety, operating regime, economy. Basic technical characteristics of WWER-440 and WWER-1000. (orig.) [de

Behaviour of Spent WWER fuel under long term storage conditions

Energy Technology Data Exchange (ETDEWEB)

Kadarmetov, I M [A.A.Bochvar All-Russia Research Institute of Inorganic Materials, Moscow (Russian Federation)

1999-07-02

Results of experimental investigation into thermomechanical properties of pre-irradiated Zr-1%Nb alloy over a range temperatures 500-570 grad C are presented. Safety examination of the Ventilation Storage Casks dry storage system has been carried out. Preliminary safety criteria under dry storage conditions in an environment of inert gas are follows: maximum cladding temperature under normal conditions of dry storage should not exceed 330 grad C after 5-year cooling in water-filled pools; maximum allowable temperature of spent fuel rod cladding under operational mode with infringement of heat removal should not exceed 440 grad C over 8 hours. As each SFA dry storage project comprises its individual technology of spent fuel management, it is necessary to evaluate allowable parameters (terms of storage, maximum temperatures of fuel) for each project respectively. The programme of experimental investigations for the justification of safety criteria for WWER-1000 dry spent fuel storage systems is underway. (author)

Influence of the heat transfer to the building structures on the confinement parameters in case of a 200 mm LOCA on units 3 and 4 of NPP Kozloduy with reactors WWER-440/V230

International Nuclear Information System (INIS)

Stanev, I.

2001-01-01

The authors present a general analysis of the mass and energy balance in the WWER-440/V230 confinement structure in case of a 200 mm LOCA, based on results from CONTAIN calculations. The character of the heat transfer to the confinement building structures is analyzed and its influence on the confinement parameters is evaluated. The results show that the building structures heat consumption is comparable to that of the Spray System heat exchanger. (author)

Solution of safety problems for nuclear power plants with WWER-440 reactors

International Nuclear Information System (INIS)

Krett, V.; Pernitsa, R.; Pfann, Ya.; Zbeglik, J.

1982-01-01

Institute of nuclear research (INR) of Czechoslovakian Atomic Energy Commission isto fulfil the supervision functions within the field of nuclear power research and development. The problems of safe operation ensurance for the nuclear power plants (NPP) with WWER-440 reactors are studied within the frame of sever major issues: code standardization and devolopment of guiding materials for the state supervision; neutronic and thermohydrolic data processing for the accident analysis; operation reliability studies of the safety systems and estimates of separate component failure importance; assessment of the accidents resulting from the equipment misfunctioning and component failures; development of a controlled reliability program; evaluation of the atomic installationsimpact on the environment; ensurence of the reactor vessel reliability and durability under irradiation. The NPP safety analysis incorporates the calculations of transient and accidental regimes for the core, the primary loop and the entire plant. A number of codes has been produced which allow to determine the state of fuel elements during operation just before the accidents assessed, thermohydrolic conditions in the coolant and the temperature distribution within the fuel both for the stationary reactor conditions and for transient regimes. A mathematical model has been deveoloped, including the description of all the primary loop major components. The Soviet code DYNAMIKA has been adopted and adjusted for EC-1040 computer, there by the accident analysis for the entire NPP has been made possible. On the basis of american SAFTE code a faster SAFEDO-2 code has been developed employing the Monte Carlo method for the accident analysis of a complex system described by means of a failure tree. The discussed codes are used at the data assessment for the accident analysis part of the safety reports as well as for the reliability evaluation of the emergency core cooling system [ru

Comment on the in-core measurement in the WWER nuclear power plant

International Nuclear Information System (INIS)

Krett, V.; Dach, K.; Erben, O.

1985-01-01

The activity of the Nuclear Research Institute (NRI) Rez in the field of in-core measurement sensors is described in the paper. The results of comparison and calibration experiments realized on the WWR-S research reactor at the NRI are presented. Measurements with fission calorimeters and SPN detectors carried out in the framework of diagnostic fuel assembly program of WWER NPP reactors are described. Noise measurements with detectors of in-core instrumentation of diagnostic fuel assemblies are also mentioned. Comparison experiments on the WWER-440 NPP reactor are described and the method of function verification of neutron sensors of the in-core control system of these reactors is given. (author)

Modal analysis of spent fuel cask for WWER-1000 reactors

International Nuclear Information System (INIS)

Azimfar, S. A.; Kazemi, A.

2011-01-01

The Spent Fuel Assemblies of WWER-1000 reactors are planned to be transported by special containers which are supposed to be designed in a manner to stand against vibrations and impacts in order to protect the spent fuel from any possible damage. The vibration opposition of these containers shall be far beyond the critical resonance, because the resonances about the natural frequency of the structure will cause the enhancement of its oscillation range and may end with its disintegration. Determination of the amounts of natural frequencies and their mode shape can be achieved by vibration analyzing methods. The amount of the natural frequency of any structure crucially depends on its shape, material and lean points as well as the amount of the loads and the type of these loads. Due to the fact that the Spent Fuel Casks used for transportation in nuclear power plants in Russian Federation are TK-13 type and the pieces of information released are negligible, the scientists in Russia are working on the design and analysis of a new type made up of composite Material. In the presented paper the cask of spent fuel of TK-13 is modeled by ANSYS at 10.0 and ten natural frequency modes have been calculated, followed by the comparison of this result with the composite cask.

Fuel pin bowing and related investigation of WWER-440 control rod influence on power release inside of neighbouring fuel pins

International Nuclear Information System (INIS)

Mikus, J.

2005-01-01

The purpose of this work consists in investigation of the WWER-440 control rod (CR) influence on space power distribution, especially from viewpoint of the values and gradient occurrence that could result in static and cyclic loads with some consequences, e.g. fuel pin bowing. As known, CR can cause power peaks in periphery fuel pins of adjacent operating assemblies because of the butt joint design of the absorbing adapter to the CR fuel part, that is, presence of the water cavity resulting in a flash up of thermal neutrons. As a consequence, beside well-known peaks in axial power distribution, above power gradients can occur inside of mentioned fuel pins. Because of complicated geometry and material composition of the CR, the detailed calculations concerning both above phenomena are complicated, too. Therefore it is useful to acquire appropriate experimental data to investigate mentioned influence and compare them with calculations. Since detailed power distributions cannot be obtained in the NPP, needed information is provided by means of experiments on research reactors. In case of measurements inside of fuel pins, special (e.g. track) detectors placed between fuel pellets are used. Such works are relatively complicated and time consuming, therefore an evaluation based on mathematical modelling and numerical approximation was proposed by means of that, and using measured power release in some selected fuel pins, information about power release inside of one of these fuel pins, can be obtained. For this purpose, an experiment on light water, zero-power research reactor LR-0 was realized and axial power distribution measurements were performed in a WWER-440 type core near to an authentic CR model. Application of the above evaluation method is demonstrated on one ''investigated'' fuel pin neighbouring CR by means of following results: 1. Axial power distribution inside of investigated fuel pin in two opposite positions on its pellets surface that are situated to

Calculation of fluences of fast neutrons hitting the pressure vessel of the Dukovany NPP WWER-440 reactor. Part I. Theory, calculations, comparison with the experiment

International Nuclear Information System (INIS)

Rataj, J.

1993-10-01

The method of calculating neutron spectra and integral flux densities of neutrons hitting the pressure vessel of the Dukovany NPP WWER-440 reactor is outlined. The one-dimensional and two-dimensional calculations were performed by means of the DORT code in R, R-Z, and R-Θ geometries using the cross sections from the ELXSIR library. In the R-Θ geometry, the coupled neutron flux densities were determined. The calculated values of the maximum activation of detectors differ less than 15% from the values measured in surveillance specimens, which is within the limit of uncertainty associated with the position of the detector in the casing. The differences between the calculated and observed data behind the pressure vessel were below 4%. 10 tabs., 3 figs., 41 refs

Neutron flux uncertainty and covariances for spectrum adjustment and estimation of WWER-1000 pressure vessel fluences

International Nuclear Information System (INIS)

Boehmer, Bertram

2000-01-01

Results of estimation of the covariance matrix of the neutron spectrum in the WWER-1000 reactor cavity and pressure vessel positions are presented. Two-dimensional calculations with the discrete ordinates transport code DORT in r-theta and r-z-geometry used to determine the neutron group spectrum covariances including gross-correlations between interesting positions. The new Russian ABBN-93 data set and CONSYST code used to supply all transport calculations with group neutron data. All possible sources of uncertainties namely caused by the neutron gross sections, fission sources, geometrical dimensions and material densities considered, whereas the uncertainty of the calculation method was considered negligible in view of the available precision of Monte Carlo simulation used for more precise evaluation of the neutron fluence. (Authors)

Studying some regimes of the WWER-440 type reactor failed fuel element operation

International Nuclear Information System (INIS)

Aksenov, N.A.; Samsonov, B.V.; Sulaberidze, V.Sh.; Frej, A.K.

1981-01-01

The results of investigating the serviceability of experimental fuel elements close by type to that of the WWER-440 type reactor in the cans of which untightness in the form of small opening are made. The tests are carried out in the SM-2 reactor high temperature water loop at the temperature of 473 K, pressure of (1-2)x10 4 kPa, coolant flow rate of 3.7-5.5 m 3 /h. The analysis of the obtained results shows that the character of changes in the fission product (FP) activity in the circuit in a considerable extent is determined bt the thermal-optical conditions of the fuel element operation. If water in the gap between fuel and can does not boil, activity changes smoothly and bursts caused by increased FP release are observed only under transient conditions of reactor operation. In the presence of water boiling in the gap the FP release has of impulse character with the frequency determined besides the untightness dimension by free volume inside the fuel element can (with its increase the pulsation frequency increases). FP release from fuel is connected with their direct escape from an open surface. When water in the gap the FP release from the fuel element occurs practically immediately. Without boiling the FP delay in the gap is determined by their diffusion in a layer of water. The conclusion is drawn that the FP release from failed fuel elements may be reduced by eliminating the water boiling in the gap between the fuel and the can by means of the fuel element power or coolant temperature decrease

Primary circuit and reactor core T-H characteristics determination of WWER 440 reactors

International Nuclear Information System (INIS)

Hermansky, J.; Petenyi, V.; Zavodsky, M.

2010-01-01

The WWER-440 nuclear fuel vendor permanently improves the assortment of produced nuclear fuel assemblies for achieving better fuel cycle economy and reactor operation safety. During unit refuelling there also could be made some other changes in hydraulic parameters of primary circuit (change of impeller wheels, hydraulic resistance coefficient changes of internal parts of primary circuit, etc.). Therefore it is necessary to determine real coolant flow rate through the reactor during units start-up after their refuelling, and also to have the skilled methodology and computing code for analyzing factors, which affecting the inaccuracy of coolant flow redistribution determination through reactor on flows through separate parts of reactor core in any case of parallel operation of different assembly types. Computing code TH-VCR and CORFLO are used for reactor core characteristics determination for one type of fuel and control assemblies and also in case of parallel operation of different assembly types. The code TH-VCR is able to calculate coolant flow rate for different combinations of three different fuel assembly channel types and three different control assembly channel types. The CORFLO code deals the area of the reactor core which consists of 312 fuel assemblies and 37 control assemblies. Regarding the rotational 60 deg symmetry of reactor core only 1/6 of reactor core with 59 fuel assemblies is taken into account. Computing code CORFLO is verified and validated at this time. Paper presents some results from measurements of coolant flow rate through reactors during start-up after unit refuelling and short description of computing code TH-VCR and CORFLO with some calculated results. (Authors)

Use of NESTLE computer code for NPP transition process analysis

International Nuclear Information System (INIS)

Gal'chenko, V.V.

2001-01-01

A newly created WWER-440 reactor model with use NESTLE code is discussed. Results of 'fast' and 'slow' transition processes based on it are presented. This model was developed for Rovno NPP reactor and it can be used also for WWER-1000 reactor in Zaporozhe NPP

Fuel Management of WWER-1000 Reactors of Kudankulam Nuclear Power Plant, India

International Nuclear Information System (INIS)

Pandey, Y.; Chauhan, A.

2008-01-01

Two units of WWER-1000 reactors of Russian design are under construction at Kudankulam site in India. These reactors are expected to be commissioned in 2008. The fuel management services for these reactors shall be carried out using Russian Computer codes. This paper includes a brief description of the core, fuel assembly lattice and physics modeling of the lattice and core for these reactors. Presented in this paper are the salient features of the core load pattern designs and fuel performance for 8 operating cycles of these reactors. The paper describes key improvements in the core load pattern designs to enhance the fuel utilization and its thermal behaviour. Presented in the paper are also the on site fuel management strategies with regard to fuel inventory and nuclear material accounting. A computer code for Fuel Inventory and Nuclear Material Accounting (FINMAC) has been developed for this purpose. The code FINMAC takes care of receipt of fresh fuel, flow between various accounting sub areas (ASAs), burnup or production of nuclear isotopes in the reactor cores and discharge from the reactor core. The code generates Material Balance Reports (MBRs) and Composition of Ending Inventory Reports (COEIs) as per the IAEA standards. (authors)

WWER-1000 reactor simulator. Material for training courses and workshops. 2. ed

International Nuclear Information System (INIS)

2005-01-01

The International Atomic Energy Agency (IAEA) has established an activity in nuclear reactor simulation computer programs to assist its Member States in education. The objective is to provide, for a variety of advanced reactor types, insight and practice in their operational characteristics and their response to perturbations and accident situations. To achieve this, the IAEA arranges for the development and distribution of simulation programs and educational material and sponsors courses and workshops. The workshops are in two parts: techniques and tools for reactor simulator development; and the use of reactor simulators in education. Workshop material for the first part is covered in the IAEA publication: Training Course Series No.12, Reactor Simulator Development (2001). Course material for workshops using a pressurized water reactor (PWR) simulator developed for the IAEA by Cassiopeia Technologies Inc. of Canada is presented in the IAEA publication, Training Course Series No. 22, 2nd edition, Pressurized Water Reactor Simulator (2005) and Training Course Series No.23, 2nd edition, Boiling Water Reactor Simulator (2005). This report consists of course material for workshops using the WWER-1000 Reactor Department Simulator from the Moscow Engineering and Physics Institute, Russian Federation

Characteristics of WWER-1000 fuel rod claddings and FA components from E635 alloy at burnups up to 72 MWd/kgU

International Nuclear Information System (INIS)

Nikulin, A.; Novikov, A.; Peregud, M.; Shishov, V.; Shevyakov, A.; Volkova, I.; Novoselov, A.; Kobylyansky, G.

2011-01-01

In this paper operation experience, results of investigated E365 alloy components of Balakovo NPP Unit 1 and Kalinin NPP unit 1 fuel assemblies are presented. Appearance, shape changes and geometric size, corrosion state of guide thimbles, angles and fuel rods, corrosion of fuel claddings are studied. At the end authors concluded that: I) E635 alloy corroborated its high operation reliability as fuel claddings and WWER-1000 FA components during 6 year service to the fuel burnup of 72MWd/kgU; II) Based on the results from the post-irradiation investigations of the fuel rods and other structural elements of WWER-1000 FAA, fabricated from E635 alloy, in terms of the basic operational characteristics, their resources after the 6 year operation cycle have not been exhausted; III) The geometrical parameters, corrosion states, tensile properties of items fabricated from fuel alloy did not attain the values that would prevent their further operation: 1) the elongations of the fuel rods at the mean burnups up to 66.2 MWd/kgU do not exceed 15 mm or 4.9%; 8) the amount of the oxide coat at surface of GT and CT does not exceed 45 μm, the hydrogen content is <0.03% mass; 9) the oxide coat at the surfaces of the frame angles does not exceed 50 μm, the hydrogen content is <0.04% mass

Seismic response and resistance capacity of 'as built' WWER 440-230 NPP Kozloduy: Verification of the results by experiments and real earthquake

International Nuclear Information System (INIS)

Sachanski, S.

1993-01-01

Although Kozloduy NPP units 1 and 2 were not designed for earthquakes they have withstood successfully the Vrancea Earthquake in 1977 with sire peak ground acceleration of 83 sm/s 2 . Both units as well as units 3 and 4 were later recalculated for maximum peak acceleration of 0.1 g. According to values calculated by two-dimensional model, in 1980 reactor buildings had sufficient earthquake resistance capacity for the accepted design seismic excitation. The non symmetric design of WWER-440 structures in plan and elevation, the large eccentricity between the center of rigidities and masses as well as technological connections between the separate substructures and units led to complicated space response and rotational effects which cannot be calculated by two-dimensional models. Three dimensional detailed 'as built' mathematical models were established and verified by series of experiments and real earthquake for: detailed analysis of 'as built' structural response, comparing the results of two and three dimensional models, detailed analyses of seismic safety margins

Automatized welding equipment for manufacturing steel cells for special buildings

International Nuclear Information System (INIS)

Weikert, F.; Winter, K.P.

1986-01-01

In GDR's nuclear power plant construction, reinforced concrete wall cells are used to construct pressure and full pressure containments for WWER-440 and WWER-1000 reactors, respectively. Welding processes for the prefabrication of steel cells as reinforcement have been automatized in order to increase both labor productivity and quality assurance. 11 figs

TORT application in reactor pressure vessel neutron flux calculations

International Nuclear Information System (INIS)

Belousov, S.I.; Ilieva, K.D.; Antonov, S.Y.

1994-01-01

The neutron flux values onto reactor pressure vessel for WWER-1000 and WWER-440 reactors, at the places important for metal embrittlement surveillance have been calculated by 3 dimensional code TORT and synthesis method. The comparison of the results received by both methods confirms their good consistency. (authors). 13 refs., 4 tabs

Analysis of WWER-440 and PWR RPV welds surveillance data to compare irradiation damage evolution

Energy Technology Data Exchange (ETDEWEB)

Debarberis, L. [Joint Research Centre of the European Commission, Institute for Energy, P.O. Box 2, 1755 ZG Petten (Netherlands)]. E-mail: luigi.debarberis@cec.eu.int; Acosta, B. [Joint Research Centre of the European Commission, Institute for Energy, P.O. Box 2, 1755 ZG Petten (Netherlands)]. E-mail: beatriz.acosta-iborra@jrc.nl; Zeman, A. [Joint Research Centre of the European Commission, Institute for Energy, P.O. Box 2, 1755 ZG Petten (Netherlands); Sevini, F. [Joint Research Centre of the European Commission, Institute for Energy, P.O. Box 2, 1755 ZG Petten (Netherlands); Ballesteros, A. [Tecnatom, Avd. Montes de Oca 1, San Sebasitan de los Reyes, E-28709 Madrid (Spain); Kryukov, A. [Russian Research Centre Kurchatov Institute, Kurchatov Square 1, 123182 Moscow (Russian Federation); Gillemot, F. [AEKI Atomic Research Institute, Konkoly Thege M. ut 29-33, 1121 Budapest (Hungary); Brumovsky, M. [NRI, Nuclear Research Institute, Husinec-Rez 130, 25068 Rez (Czech Republic)

2006-04-15

It is known that for Russian-type and Western water reactor pressure vessel steels there is a similar degradation in mechanical properties during equivalent neutron irradiation. Available surveillance results from WWER and PWR vessels are used in this article to compare irradiation damage evolution for the different reactor pressure vessel welds. The analysis is done through the semi-mechanistic model for radiation embrittlement developed by JRC-IE. Consistency analysis with BWR vessel materials and model alloys has also been performed within this study. Globally the two families of studied materials follow similar trends regarding the evolution of irradiation damage. Moreover in the high fluence range typical of operation of WWER the radiation stability of these vessels is greater than the foreseen one for PWR.

OPAL- the in-core fuel management code system for WWER reactors

International Nuclear Information System (INIS)

Krysl, V.; Mikolas, P.; Sustek, J.; Svarny, J.; Vlachovsky, K.

2002-01-01

Fuel management optimization is a complex problem namely for WWER reactors, which at present are utilizing burnable poisons (BP) to great extent. In this paper, first the concept and methodologies of a fuel management system for WWER 440 (NPP Dukovany) and NPP WWER 1000 (NPP Temelin) under development in Skoda JS a.s. are described and followed by some practical applications. The objective of this advanced system is to minimize fuel cost by preserving all safety constraints and margins. Future enhancements of the system will allow is it to perform fuel management optimization in the multi-cycle mode. The general objective functions of the system are the maximization of EOC reactivity, the maximization of discharge burnup, the minimization of fresh fuel inventory / or the minimization of feed enrichment, the minimization of the BP inventory. There are also safety related constraints, in which the minimization of power peaking plays a dominant role. The core part of the system requires meeting the major objective: maximizing the EOC Keff for a given fuel cycle length and consists of four coupled calculation steps. The first is the calculation of a Loading Priority Scheme (LPS). which is used to rank the core positions in terms of assembly Kinf values. In the second step the Haling power distribution is calculated and by using fuel shuffle and/or enrichment splitting algorithms and heuristic rules the core pattern is modified to meet core constraints. In this second step a directive/evolutionary algorithm with expert rules based optimization code is used. The optimal BP assignment is alternatively considered to be a separate third step of the procedure. In the fourth step the core is depleted in normal up to 3D pin wise level using the BP distribution developed in step three and meeting all constraints is checked. One of the options of this optimization system is expert friendly interactive mode (Authors)

Cooperation of Atomehnergoehksport and Skodaexport in the sphere of atomic power engineering

International Nuclear Information System (INIS)

Gulko, V.D.

1986-01-01

The cooperation is briefly outlined of the Czechoslovak foreign trade organization Skodaexport and its Soviet counterpart Atomehnergoehksport in nuclear power engineering. Thanks to this cooperation within socialist economic integration, 12 WWER-440 units of a total capacity of 5,280 MWe will be built in Czechoslovakia by 1990 followed by the construction of WWER-1000 reactors. Thus, by the year 2000, the total installed capacity in Czechoslovakia will be 15 to 16 thousand MWe. The reactors are being built according to Soviet project designs, with active participation of Soviet experts and organizations. Within the project of cooperation, the Soviet Union also supplies Czechoslovakia with nuclear fuel and regularly provides spent fuel disposal. On the other hand, Czechoslovakia supplies the Soviet Union and other CMEA member countries with reactor components, especially WWER-440 primary circuit equipment, and will become the main supplier of WWER-1000 primary circuit equipment, both according to Soviet project designs. This and close cooperation of Czechoslovak and Soviet organizations ranks Czechoslovakia among the major suppliers of technological equipment for nuclear power plants in CMEA countries. (L.O.)

Rossendorf Research Center, Institute of Safety Research. Annual report 1991

International Nuclear Information System (INIS)

Boehmert, J.; Weiss, F.P.

1992-08-01

The working program covers above all topics concerning the assessment of design basis safety and the increase of operational safety of the WWER type reactors. The topics are directed to the WWER-440/213 type and to the WWER-1000 type, and are dealt with by the three departments, i.e. incident analysis, neutron embrittlement, and mechanical integrity. One paper is concerned with the determination of the neutron field of HERA. (orig.) [de

Co-ordinated research programme on benchmark study for the seismic analysis and testing of WWER-type nuclear power plants. V. 3G. Kozloduy NPP units 5/6: Analysis and testing. Working material

International Nuclear Information System (INIS)

1999-01-01

In August 1991, following the SMiRT-11 Conference in Tokyo, a Technical Committee Meeting was held on the 'Seismic safety issues relating to existing NPPs'. The Proceedings of this TCM was subsequently compiled in an IAEA Working Material. One of the main recommendations of this TCM, called for the harmonization of criteria and methods used in Member States in seismic reassessment and upgrading of existing NPPs. Twenty four institutions from thirteen countries participated in the CRP named 'Benchmark study for the seismic analysis and testing of WWER type NPPs'. Two types of WWER reactors (WWER-1000 and WWER-440/213) selected for benchmarking. Kozloduy NPP Units 5/6 and Paks NPP represented these respectively as prototypes. Consistent with the recommendations of the TCM and the working paper prepared by the subsequent Consultants' Meeting, the focal activity of the CRP was the benchmarking exercises. A similar methodology was followed both for Paks NPP and Kozloduy NPP Unit 5. Firstly, the NPP (mainly the reactor building) was tested using a blast loading generated by a series of explosions from buried TNT charges. Records from this test were obtained at several free field locations (both downhole and surface), foundation mat, various elevations of structures as well as some tanks and the stack. Then the benchmark participants were provided with structural drawings, soil data and the free field record of the blast experiment. Their task was to make a blind prediction of the response at preselected locations. The analytical results from these participants were then compared with the results from the test. Although the benchmarking exercises constituted the focus of the CRP, there were many other interesting problems related to the seismic safety of WWER type NPPs which were addressed by the participants. These involved generic studies, i.e. codes and standards used in original WWER designs and their comparison with current international practice; seismic analysis

Burnup influence on the WWER-1000 reactor vessel neutron fluence evaluation

International Nuclear Information System (INIS)

Panayotov, I.; Mihaylov, N.; Ilieva, K.; Kirilova, D.; Manolova, M.

2009-01-01

The neutron fluence of the vessels of the reactors is determined regularly accordingly the RPV Surveillance Program of Kozloduy NPP Unit 5 and 6 in order to assess the state of the metal vessel and their radiation damaging. The calculations are carried out by the method of discrete ordinates used in the TORT program for operated reactor cycles. An average reactor spectrum corresponding to fresh U-235 fuel is used as an input neutron source. The impact of the burn up of the fuel on the neutron fluence of WWER-1000 reactor vessel is evaluated. The calculations of isotopic concentrations of U-235 and Pu-239 corresponding to 4 years burn up were performed by the module SAS2H of the code system SCALE 4.4. Since fresh fuel or 4 years burn up fuel assembly are placed in periphery of reactor core the contribution of Pu-239 of first year burn up and of 4 years burn up is taken in consideration. Calculations of neutron fluence were performed with neutron spectrum for fresh fuel, for 1 year and for 4 years burn up fuel. Correction factors for neutron fluence at the inner surface of the reactor vessel, in ? depth of the vessel and in the air behind the vessel were obtained. The correction coefficient could be used when the neutron fluence is assessed so in verification when the measured activity of ex-vessel detectors is compared with calculated ones. (Authors)

New welding and finishing procedures

International Nuclear Information System (INIS)

1992-01-01

The proceedings contain texts of the 31 contributions presented at the conference. One of them, dealing with the reheat crackability in the heat affected zone of steels for WWER-440 and WWER-1000 reactor vessels, has been inputted in INIS. The behavior of the steels was determined by the simulation technique. (M.D.). 4 figs., 5 tabs., 5 refs

Computer simulation of WWER - 440 normal and emergency transient operating conditions

International Nuclear Information System (INIS)

Izbeshesku, M.; Rajka, V.; Untaru, S.; Dumitresku, A.; Paneh, M.; Turku, I.

1976-01-01

Results of computer realization of a model for studying transient process in the nuclear system of vapour production at the WWER - 40 peactor nuclear power plant are presented. The first circuit model consists of a number of modules, corresponding to its main parts: for each module derived were the equations describing neutron and thermohydraulic parameters. The second circuit effect is taken into account by heat quantity accepted from a steam generator. The equations are mostly differential with constant coefficients. Coefficient values and initial values of physical quantities are evaluated according to the technical literature. Both manual and automatic operations are modelled [ru

Comparative calculations and operation-to-PIE data juxtaposition of the Zaporozhye NPP, WWER-1000 FA-E0325 fuel rods after 4 years of operation up to ∼49 MWd/kgU burnup

International Nuclear Information System (INIS)

Passage, G.; Stefanova, S.; Scheglov, A.; Proselkov, V.

2006-01-01

Operational and PIE data for the Zaporozhe NPP, FA-E0325, WWER-1000 fuel rods were provided in the OECD NEA IFPE Database and were used to perform comparative calculations among several fuel performance codes. The fuel rods had been irradiated for 4 years of operation up to ∼49 MWd/kg U burnup. The fuel rod operation histories are developed for the PINw99, TRANSURANUS (V1M1J03) and TOPRA-2 codes. The initial state fuel rod parameters are analysed and calculations are carried out. The PIE data enable the comparison of experimental measurement with code-calculated values for cladding elongation (49 rods), FGR and gas pressure (35 rods). Cladding diameter creep-down and gap closure results are juxtaposed as well. The capability of the applied codes correctly to predict the WWER fuel rod performance is shown. The WWER-1000 fuel rod data include initial geometrical and design parameters of the fuel rods, as well as description of the operation regime, NPP unit loading history and PIE results at normal conditions. The data are sufficient for modelling all 312 fuel rod and for comparison of calculations with experimental results for a limited number of fuel rods. The comparison between the calculated and measured results discussed in this paper shows that the codes PINw99, TRANSURANUS and TOPRA-2, are capable of adequate predicting the thermophysical and the mechanical performance of the WWER-1000 fuel rods. The PINw99 code predicts conservative BOL FGR values and conservative gas pressure values in the region of burnups higher than 30 MWd/kg U, which can be explained by the underprediction of the cladding gas inner volume and cladding elongation. The improved version PIN2K (not applied in the present study) predicts much better FGR and gas pressure, though, it is still under development in the high burnup FGR modelling part. In the TRANSURANUS code, there are also areas, where refinements are clearly indicated. They are subjects of the ongoing research projects and

Experience in scientific guidance during start-up and normal operation of NPPs with WWER reactors; Opyt nauchnogo rukovodstva puskom i soprovozhdeniya pri ehkspluatatsii ehnergoblokov AEhS s WWER

Energy Technology Data Exchange (ETDEWEB)

Abagyan, A; Kazakov, V; Kryakvin, L [All-Russian Inst. for NPP Operation, Moscow (Russian Federation)

1996-12-31

The experience gained in the All-Russian Research Institute of NPP Operation (RU) in improvement of reactor start-up and normal operation of NPPs has been reported. The work was carried out on NPPs in Russia, Ukraine, Bulgaria, Hungary and Czechoslovakia. All scientific programmes applied use the system approach, modern methods of safety assessment and the principle of loss effect optimization. For the Kozloduy NPP the following projects have been implemented: design of accelerated unloading system for WWER-1000; refinement of water feeding unit for the WWER-1000 steam generator; response analysis of the safety anti-breakdown system of the second loop. The importance of technical substantiation in the process of decision making is stressed. 6 refs.

Analysis of a large break LOCA in the cold leg of the WWER-440/W-213 plant Griefswald, Unit 5

International Nuclear Information System (INIS)

Horche, W.

1993-01-01

The Gessellschaft fur Anlagen und Reaktorsicherheit (GRS) has performed a safety evaluation of the nuclear power plant (NPP) Greifswald, unit 5, of the Soviet type WWER-440/W-213, in cooperation with the French Institute de Protection of de Surete Nucleaire (IPSN) and other partners. Within this project an independent accident analysis is performed by GRS in order to assess the results of existing analysis and to supplement them. In this paper the analysis of the double-ended guillotine break (DEGB) of one cold leg of the main circulation pipe is described. The major objective of the calculation was the investigation of the accident sequence with reduced availability of the emergency core cooling system (single failure criterion). In addition, the simultaneous loss of onsite and offsite power and the failure of scram were assumed. The thermal-hydraulic system code ATHLET/FLUT, developed at GRS and already applied for the safety analysis of several WWER plants, was chosen again. The pressure in the confinement, the back pressure for the discharge model, was calculated as a function of time for this accident separately with GRS-Code RALOC. Furthermore, it was necessary to model the local concentration of direct accumulator injection into the reactor vessel with the help of a special two-channel model of the core and upper plenum. For this model, results were considered obtained from the 1:1 scaled test facility UPTF. It was assumed that only 25% of the upper plenum and core volume is directly penetrated by the injected water. The DEGB was defined in that loop, which is connected with one of three low-pressure injection subsystems. This means that this injected water flows towards the leak without passing the core. As single failure the failure of one of three diesel generators was assumed. The full paper will contain nodalization schemes, which are generated by the ATHLET-Input-Grafic

Investigation of coolant mixing in WWER-440/213 RPV with improved turbulence model

International Nuclear Information System (INIS)

Kiss, B.; Aszodi, A.

2011-01-01

A detailed and complex RPV model of WWER-440/213 type reactor was developed in Budapest University of Technology and Economics Institute of Nuclear Techniques in the previous years. This model contains the main structural elements as inlet and outlet nozzles, guide baffles of hydro-accumulators coolant, alignment drifts, perforated plates, brake- and guide tube chamber and simplified core. With the new vessel model a series of parameter studies were performed considering turbulence models, discretization schemes, and modeling methods with ANSYS CFX. In the course of parameter studies the coolant mixing was investigated in the RPV. The coolant flow was 'traced' with different scalar concentration at the inlet nozzles and its distribution was calculated at the core bottom. The simulation results were compared with PAKS NPP measured mixing factors data (available from FLOMIX project. Based on the comparison the SST turbulence model was chosen for the further simulations, which unifies the advantages of two-equation (kω and kε) models. The most widely used turbulence models are Reynolds-averaged Navier-Stokes models that are based on time-averaging of the equations. Time-averaging filters out all turbulent scales from the simulation, and the effect of turbulence on the mean flow is then re-introduced through appropriate modeling assumptions. Because of this characteristic of SST turbulence model a decision was made in year 2011 to investigate the coolant mixing with improved turbulence model as well. The hybrid SAS-SST turbulence model was chosen, which is capable of resolving large scale turbulent structures without the time and grid-scale resolution restrictions of LES, often allowing the use of existing grids created for Reynolds-averaged Navier-Stokes simulations. As a first step the coolant mixing was investigated in the downcomer only. Eddies are occurred after the loop connection because of the steep flow direction change. This turbulent, vertiginous flow was

Co-ordinated research programme on benchmark study for the seismic analysis and testing of WWER-type nuclear power plants. V. 3I. Kozloduy NPP units 5/6: Analysis and testing. Working material

International Nuclear Information System (INIS)

1999-01-01

In August 1991, following the SMiRT-11 Conference in Tokyo, a Technical Committee Meeting was held on the 'Seismic safety issues relating to existing NPPs'. The Proceedings of this TCM was subsequently compiled in an IAEA Working Material. One of the main recommendations of this TCM, called for the harmonization of criteria and methods used in Member States in seismic reassessment and upgrading of existing NPPs. Twenty four institutions from thirteen countries participated in the CRP named 'Benchmark study for the seismic analysis and testing of WWER type NPPs'. Two types of WWER reactors (WWER-1000 and WWER-440/213) selected for benchmarking. Kozloduy NPP Units 5/6 and Paks NPP represented these respectively as prototypes. Consistent with the recommendations of the TCM and the working paper prepared by the subsequent Consultants' Meeting, the focal activity of the CRP was the benchmarking exercises. A similar methodology was followed both for Paks NPP and Kozloduy NPP Unit 5. Firstly, the NPP (mainly the reactor building) was tested using a blast loading generated by a series of explosions from buried TNT charges. Records from this test were obtained at several free field locations (both downhole and surface), foundation mat, various elevations of structures as well as some tanks and the stack. Then the benchmark participants were provided with structural drawings, soil data and the free field record of the blast experiment. Their task was to make a blind prediction of the response at preselected locations. The analytical results from these participants were then compared with the results from the test. Although the benchmarking exercises constituted the focus of the CRP, there were many other interesting problems related to the seismic safety of WWER type NPPs which were addressed by the participants. These involved generic studies, i.e. codes and standards used in original WWER designs and their comparison with current international practice; seismic analysis

Experience in start-up of the South-Ukrainian-2 power unit with the WWER-1000 reactor

International Nuclear Information System (INIS)

Belov, Yu.V.; Kazakov, V.A.; Kirilov, V.V.; Kryakvin, L.V.

1987-01-01

The volume, sequence and dates of works fulfilled during hot testing, physical and power start-ups and while bringing output of the South-Ukranian-2 power unit with the WWER-1000 reactor to the design figure are described. The works were fulfilled according to the standard schedules from October in 1984 till April in 1985. Combination of the stages and intensification of works before the physical start-up have allowed to shorten the dates by 90 days as compared to the schedule. The physical and power start-ups, including bringing reactor output to the design figure, were performed during 140 days, that permits to shorten the dates by 20 days more. The results of physical experiments carried out at the South-Ukranian-2 power unit, are in good agreement with the data obtained at the first power units of the given and Kalinin NPPs. Besides, during physical and power start-ups additional measures ensuring nuclear safety are developed

Computation code TEP 1 for automated evaluation of technical and economic parameters of operation of WWER-440 nuclear power plant units

International Nuclear Information System (INIS)

Zadrazil, J.; Cvan, M.; Strimelsky, V.

1987-01-01

The TEP 1 program is used for automated evaluation of the technical and economic parameters of nuclear power plant units with WWER-440 reactors. This is an application program developed by the Research Institute for Nuclear Power Plants in Jaslovske Bohunice for the KOMPLEX-URAN 2M information system, delivered by the USSR to the V-2 nuclear power plants in Jaslovske Bohunice and in Dukovany. The TEP 1 program is written in FORTRAN IV and its operation has two parts. First the evaluation of technical and economic parameters of operation for a calculation interval of 10 mins and second, the control of the calculation procedure, follow-up on input data, determination of technical and economic parameters for a lengthy time interval, and data printout and storage. The TEP 1 program was tested at the first unit of the V-2 power plant and no serious faults appeared in the process of the evaluation of technical and economic parameters. A modification of the TEP 1 programme for the Dukovany nuclear power plant is now being tested on the first unit of the plant. (Z.M.)

Structural optimization of static power control programs of nuclear power plants with WWER-1000

International Nuclear Information System (INIS)

Kokol, E.O.

2015-01-01

The question of possibility the power control programs switching for WWER-1000 is considered. The aim of this research is to determine the best program for the power control of nuclear reactor under cyclic diurnal behavior of electrical generation, as well as the switching implementation. The considered problem of finding the best control program refers to the multicriteria optimization class of problems. Operation of the nuclear power generation system simulated using the following power control programs: with constant average temperature of transfer fluid, with constant pressure in the reactor secondary circuit, with constant temperature in input of the nuclear reactor. The target function was proposed. It consists of three normalized criteria: the burn up fraction, the damage level of fuel rod array shells, as well as changes in the power values. When simulation of the nuclear power generation system operation within the life was done, the values of the selected criteria were obtained and inserted in the target function. The minimum of three values of the target function depending on the control program at current time defined the criterion of switching of considered static power control programs for nuclear power generation system

Increasing of leak-tightness of hermetic zone and other important components in NPPs

International Nuclear Information System (INIS)

Murani, J.

2001-01-01

The performed by VUEZ resealing works in the hermetic compartments/containment of WWER 440 and WWER 1000 NPPs in Slovakia (Jaslovske Bohunice V-1 NPP, Jaslovske Bohunice V-2 NPP, Mochovce NPP), the Czech Republic (Dukovany NPP, Temelin NPP) and Hungary (Pask NPP) are presented. The leakage rate from hermetic compartments at individual NPP reactor units are shown.The VUEZ activities in field of resealing of weld joints in pools and tanks in the Jaslovske Bohunice V-1 NPP and innovation of the seal of reactor pit protective hood (kolpak) are described. The principle of operation and practical experience of the SMU-V system implemented in the Jaslovske Bohunice V-1 NPP (WWER 440 - V 230) for NPP primary circuit leakage monitoring are also given

Severe accident management development program for VVER-1000 and VVER-440/213 based on the westinghouse owners group approach

International Nuclear Information System (INIS)

Felix, E.; Dessars, N.

2003-01-01

The development of the Westinghouse Owners Group Severe Accident Management Guidelines (WOG SAMG) between 1991 and 1994 was initiated in response to the U.S. Nuclear Regulatory Commission (NRC) requirement for addressing the regulatory severe accident concerns. Hence, the WOG SAMG is designed to interface with other existing procedures at the plant and is used in accident sequences that have progressed to the point where these other procedures are not applicable any longer, i.e. following core damage. The primary purpose of the WOG SAMG is to reach a controlled stable state, which can be declared when fission product releases are controlled, challenges to the confinement fission product boundary have been mitigated, and adequate heat removal is provided to the core and the containment. Although the WOG SAMG is a generic severe accident management guidance developed for use by the entirety of the operating Westinghouse PWR plants, provisions have been made in their development to address specific features of individual plants such as confinement type and the feasibility of reactor cavity flooding. Similarly, the generic SAMG does not address unique plant features and equipment, but rather allows for consideration of plant specific features and strategies. This adaptable approach has led to several SAMG development programs for VVER-1000 and VVER-440 type of power plants, under Westinghouse' s lead. The first of these programs carried out to completion was for Temelin NPP - VVER-1000 - in the first quarter of 2003. Other ongoing programs aim at providing a similar work for VVER-440 design, namely Dukovany, Mochovce and Bohunice NPPs. The challenge of adapting the existing generic WOG material to plants other than PWRs mainly arises for VVER-440 because of important differences in confinement design, making it more vulnerable to ex-vessel phenomena such as hydrogen burn. Also, for both eastern designs, cavity flooding strategy requires special consideration and

Transient simulations in WWER-1000-comparison between DYN3D-ATHLET and DYN3D-RELAP5

International Nuclear Information System (INIS)

Grundmann, U.; Kliem, S.; Kozmenkov, Y.; Mittag, S.; Rohde, U.; Weiss, F.P.

2003-01-01

Simulations of a real transient of an operating WWER-1000 power plant have been performed using DYN3D-ATHLET (Gru95) and DYN3D-RELAP5 (Koy01) code systems in the frame of activities aimed at a validation of the neutronic / thermal-hydraulic coupled codes. The transient initiated by a main coolant pump switching off, when three of the four main coolant pumps of the plant are in operation (scenario of the VALCO project) is chosen for the simulation. The same models of the plant (except the core nodalization) but two different libraries of macroscopic cross-sections have been used in compared calculations. Additionally, the compared code systems are based on the different / external and internal / coupling techniques. This paper contains a brief description of the coupled codes and the plant model as well as a comparison between the results from simulations (Authors)

Design works organization during the IandC system upgrading on an operating VVER power plant from the general designer's standpoint

International Nuclear Information System (INIS)

Krepel, V.

1997-01-01

Two replacements of nuclear power plant instrumentation and control systems have already been implemented according to the project design of Energoprojekt: at the Mochovce WWER-440 and the Temelin WWER-1000 plants. In the present contribution the design problems encountered during the replacement are described, the causes of the problems are discussed, and a policy of organizing project design work for an instrumentation and control system replacement at an operating WWER power plant is established such as would avoid these problems. (A.K.)

PWR and WWER fuel performance. A comparison of major characteristics

International Nuclear Information System (INIS)

Weidinger, H.

2006-01-01

PWR and WWER fuel technologies have the same basic performance targets: most effective use of the energy stored in the fuel and highest possible reliability. Both fuel technologies use basically the same strategies to reach these targets: 1) Optimized reload strategies; 2) Maximal use of structural material with low neutron cross sections; 3) Decrease the fuel failure frequency towards a 'zero failure' performance by understanding and eliminating the root causes of those defects. The key driving force of the technology of both, PWR and WWER fuel is high burn-up. Presently a range of 45 - 50 MWD/kgU have been reached commercially for PWR and WWER fuel. The main technical limitations to reach high burn-up are typically different for PWR and WWER fuel: for PWR fuel it is the corrosion and hydrogen uptake of the Zr-based materials; for WWER fuel it is the mechanical and dimensional stability of the FA (and the whole core). Corrosion and hydrogen uptake of Zr-materials is a 'non-problem' for WWER fuel. Other performance criteria that are important for high burn-up are the creep and growth behaviour of the Zr materials and the fission gas release in the fuel rod. There exists a good and broad data base to model and design both fuel types. FA and fuel rod vibration appears to be a generic problem for both fuel types but with more evidence for PWR fuel performance reliability. Grid-to-rod fretting is still a major issue in the fuel failure statistics of PWR fuel. Fuel rod cladding defects by debris fretting is no longer a key problem for PWR fuel, while it still appears to be a significant root cause for WWER fuel failures. 'Zero defect' fuel performance is achievable with a high probability, as statistics for US PWR and WWER-1000 fuel has shown

New system technologies implemented at Kozloduy 3 and 4 (WWER 440-230) for containment leakage and H2 control in severe accident situations - Design, qualification, installation, commissioning

International Nuclear Information System (INIS)

Feuerbach, R.; Eckardt, B.; Kastner, B.

2005-01-01

In order to reduce the residual risk associated with hypothetical severe nuclear accidents, systems and components for filtered containment venting and H 2 reduction were developed. During severe accident scenarios large quantities of hydrogen and radioactive material may be released into the containment atmosphere within a short period of time. In the event of internal over pressurization due to hypothetical severe accident sequences a pressure barrier system has to be created to confine the activity in the containment. Unavoidable releases of activity to the environment have to be minimized to a great extent as possible. Research into the hypothetical event of core melt accidents has continued and new accident mitigation technologies have been developed. Decisions have been taken to implement these new mitigation measures in operating nuclear power plants to mitigate severe accidents consequences. In order to prevent loss of containment integrity as a result of over pressurization, nuclear power plants in the Federal Republic of Germany as well as in most other European countries have been or will be back-fitted with systems for filtered venting of the containment atmosphere and systems for H 2 -control. Similar technologies for containment venting system and H 2 control have been now implemented in the first WWER 440-230 units of Kozloduy 3 and 4. Following OECD recommendations sever accident situations were analyzed and a design of countermeasures have been performed. Main goal of the developed countermeasures was to overcome the WWER 440-230 containment design specifics like, leakage rate behavior, limited available containment volume combined with the feature of high availability of electrical supply at multiple plant sites. Further more the design of counter measures considers the common use for Kozloduy unit 3 and 4. The analysis of postulated severs accident situation - without countermeasures - showed significant increase of H 2 /O 2 concentration in the

Experiments for neutron fluence assessment on WWER-440 and WWER-1000 pressure vessel

Energy Technology Data Exchange (ETDEWEB)

Ilieva, K; Apostolov, T; Penev, I; Trifonov, A; Taskaev, E; Belousov, S; Antonov, S; Petrova, T; Stoeva, L [Bylgarska Akademiya na Naukite, Sofia (Bulgaria). Inst. za Yadrena Izsledvaniya i Yadrena Energetika; Boyadzhiev, Z; Nelov, N; Tsocheva, V; Andreeva, I; Lilkov, B; Velichkov, V; Monev, M [Kombinat Atomna Energetika, Kozloduj (Bulgaria)

1996-12-31

The activity of shavings sampled out from the expected maximum embrittlement location (weld 4) on the inner pressure vessel wall of the Kozloduy-1 Unit after the 14-th cycle has been measured. The experiment was carried out along the INEI channel using Fe and Cu string and foil detectors. The axial neutron flux distribution at the Unit 3 after the cycle 11 has been measured and compared to the calculated values. The calculations of the expected activities have been carried out taking into account the local power distribution. A comparison between measured and calculated values using ACTIVAT code is made. It shows a discrepancy of about 20%. It is recommended to carry out ex-vessel neutron fluence measurements using a rack device with activation detectors in order to verify the calculation results. 8 refs., 3 figs., 2 tabs.

Co-ordinated research programme on benchmark study for the seismic analysis and testing of WWER-type nuclear power plants. V. 3H. Kozloduy NPP units 5/6: Analysis and testing. Working material

International Nuclear Information System (INIS)

1999-01-01

In August 1991, following the SMiRT-11 Conference in Tokyo, a Technical Committee Meeting was held on the 'Seismic safety issues relating to existing NPPs'. The Proceedings of this TCM was subsequently compiled in an IAEA Working Material. One of the main recommendations of this TCM, called for the harmonization of criteria and methods used in Member States in seismic reassessment and upgrading of existing NPPs. Twenty four institutions from thirteen countries participated in the CRP named 'Benchmark study for the seismic analysis and testing of WWER type NPPs'. Two types of WWER reactors (WWER-1000 and WWER-440/213) selected for benchmarking. Kozloduy NPP Units 5/6 and Paks NPP represented these respectively as prototypes. Consistent with the recommendations of the TCM and the working paper prepared by the subsequent Consultants' Meeting, the focal activity of the CRP was the benchmarking exercises. A similar methodology was followed both for Paks NPP and Kozloduy NPP Unit 5. Firstly, the NPP (mainly the reactor building) was tested using a blast loading generated by a series of explosions from buried TNT charges. Records from this test were obtained at several free field locations (both downhole and surface), foundation mat, various elevations of structures as well as some tanks and the stack. Then the benchmark participants were provided with structural drawings, soil data and the free field record of the blast experiment. Their task was to make a blind prediction of the response at preselected locations. The analytical results from these participants were then compared with the results from the test. Although the benchmarking exercises constituted the focus of the CRP, there were many other interesting problems related to the seismic safety of WWER type NPPs which were addressed by the participants. These involved generic studies, i.e. codes and standards used in original WWER designs and their comparison with current international practice; seismic analysis

AER working group D on WWER safety analysis - report of the 2007 meeting

International Nuclear Information System (INIS)

Kliem, S.

2007-01-01

The AER working group D on WWER reactor safety analysis held its sixteenth meeting in Paris, France during the period 08-09 May 2007. The meeting was hosted by the CEA France. It followed the final workshop on the OECD/DOE/CEA WWER-1000 Coolant Transient Benchmark held at 07 May. Altogether 11 participants attend the meeting of the working group D, 7 from AER member organizations and 4 guests from non-member organizations. The co-ordinator of the working group, Mr. S. Kliem, served as chairman of the meeting. The meeting started with a general information exchange about the recent activities in the participating organizations. The given presentations and the discussions can be attributed to the following topics: -Code development and benchmarking for reactor dynamics applications; -Safety analysis methodology and results; -Future activities. New solutions for three different benchmarks were presented and discussed. These are the Second AER Dynamic Benchmark on control rod ejection at hot zero power (S. Kliem, FZD), the WWER-1000 Coolant Transient Benchmark (E. Syrjaelahti, VTT) and the stationary AER-FCM101 Benchmark considering a WWER-1000 reactor (C. Parisi, UniPisa). A. Kereszturi (AEKI) presented a statistical evaluation of the possibility to observe a fuel assembly mis loading event. The second presentation of E. Syrjaelahti was dedicated to the description how best-estimate coupled code calculations at VTT are supported by uncertainty and sensitivity analyses. K. Velkov (GRS) presented preliminary results of BIPR8KN/ATHLET calculations with a very detailed resolution of the calculation grid on the assessment of coolant mixing inside WWER-1000 assembly heads. Coolant mixing experiments at three different mixing test facilities, modeling different reactor types, were presented and compared by S. Kliem. A calculation study using the coupled code system KORSAR/GP on the consequences of the injection of a slug of un borated water into the reactor core was

Using noise diagnostics for detection and monitoring of vibrations of RPV internals, and for cause analysis in Eastern German NPP with WWER-440/230 type reactors of the Russian design type

International Nuclear Information System (INIS)

Schumann, P.

2000-10-01

The report explains in detail applications and results of noise diagnostic measurements for examining vibrations which caused damage to reactor pressure vessel internals. The vibrations investigated were observed in 1975 and 1985 at the WWER-440/230 type reactors of the Russian design installed in units 1 and 2 of the Greifswald nuclear power plant, and were identified as dominant control element vibrations and abnormal core basket movements. The report presents essential operating characteristics recorded during disturbed reactor operation, the inspection results, and characteristic experimental findings from noise signal analyses and special tests examining the physical aspects of the vibration processes and their causes. Some recommendations have been derived relating to monitoring and minimization of such vibrations. (orig./CB) [de

Organization and mechanization of maintenance operations at NPPs with the WWER type reactors

International Nuclear Information System (INIS)

Titov, A.A.

1983-01-01

The structure of capital investments defining organization and mechanization of maintepance operations at NPPs with the WWER type reactors is analyzed. The trends in development of optimum decisions for organization and mechanization of repair obs at NPPs being designed taking into account the prospects of nuclear powep enginerning development, the system of NPP maintenance servicing, as well as the structure of repair-productive capacities are discussed. On the basis of the analysis of the data obtained in designing the Zaporozhskaya NPP it is shown that the capital investments for organizing and mechanization of maintenance operations at the unified NPP site with four WWER-1000 reactors reach nearly 18 roubles/kW. A conclusion is drawn that at present the design of an NPP with the WWER-1000 reactor totally meets the requirements of realization of periodic maintenance operations. It is advisable to cooperate the NPP management with that of a thermal power station from the viewpoint of using manpower, which would improve the operating conditions and labour productivity of workers engaged in repair and, consequently, reduce the capital investments and repair expenditures

Comparison of the updated solutions of the 6th dynamic AER Benchmark - main steam line break in a NPP with WWER-440

International Nuclear Information System (INIS)

Kliem, S.

2003-01-01

The 6 th dynamic AER Benchmark is used for the systematic validation of coupled 3D neutron kinetic/thermal hydraulic system codes. It was defined at The 10 th AER-Symposium. In this benchmark, a hypothetical double ended break of one main steam line at full power in a WWER-440 plant is investigated. The main thermal hydraulic features are the consideration of incomplete coolant mixing in the lower and upper plenum of the reactor pressure vessel and an asymmetric operation of the feed water system. For the tuning of the different nuclear cross section data used by the participants, an isothermal re-criticality temperature was defined. The paper gives an overview on the behaviour of the main thermal hydraulic and neutron kinetic parameters in the provided solutions. The differences in the updated solution in comparison to the previous ones are described. Improvements in the modelling of the transient led to a better agreement of a part of the results while for another part the deviations rose up. The sensitivity of the core power behaviour on the secondary side modelling is discussed in detail (Authors)

Main trends and content of works on fabrication of fuel rods with MOX fuel for the WWER-1000 reactor

International Nuclear Information System (INIS)

Tsykanov, V.A.; Golovanov, V.N.; Mayorshin, A.A.; Yurchenko, A.D.; Ilyenko, S.A.; Syuzev, V.N.

2000-01-01

The main trends of production of pellet MOX-fuel for the WWER reactors using the trial-experimental equipment at SSC RF RIAR are set forth. The main realized parameters of fabrication of MOX-fuel pellets are presented. The content of the reactor tests program is considered with allowance for their licensing requirements for the WWER reactors. (author)

Improving the refueling cycle of a WWER-1000 using cuckoo search method and thermal-neutronic coupling of PARCS v2.7, COBRA-EN and WIMSD-5B codes

Energy Technology Data Exchange (ETDEWEB)

Yarizadeh-Beneh, M.; Mazaheri-Beni, H.; Poursalehi, N., E-mail: n_poursalehi@sbu.ac.ir

2016-12-15

Highlights: • The cuckoo search algorithm is applied to the loading pattern optimization of a nuclear reactor core. • Calculations during the cycle show a good agreement between results and reference for the original LP. • Results indicate the efficient performance of cuckoo search approach coupled with thermal-neutronic solvers. • Neutronic parameters of proposed core pattern are improved relative to original core pattern. - Abstract: The fuel loading pattern optimization is an important process in the refueling design of a nuclear reactor core. Also the analysis of reactor core performance during the operation cycle can be a significant step in the core loading pattern optimization (LPO). In this work, for the first time, a new method i.e. cuckoo search algorithm (CS) has been applied to the fuel loading pattern design of Bushehr WWER-1000 core. In this regard, two objectives have been chosen for finding the best configuration including the improvement of operation cycle length associated with flattening the radial power distribution of fuel assemblies. The core pattern optimization has been performed by coupling the CS algorithm to thermal-neutronic codes including PARCS v2.7, COBRA-EN and WIMSD-5B for earning desired parameters along the operation cycle. The calculations have been done for the beginning of cycle (BOC) to the end of cycle (EOC) states. According to numerical results, the longer operation cycle for the semi-optimized loading pattern has been achieved along with less power peaking factor (PPF) in comparison to the original core pattern of Bushehr WWER-1000. Gained results confirm the efficient and suitable performance of the developed program and also the introduced CS method in the LPO of a nuclear WWER type.

Experimental assessment of welded joints brittle fracture on the crack arrest criterion for WWER-1000 RPV

International Nuclear Information System (INIS)

Blumin, A.A.; Timofeev, B.T.

2000-01-01

The crack arrest fracture toughness in a vessel steel used in WWER-1000 reactor, namely in steel 15Kh2NMFA and its submerged arc welded joints, produced with Sv-08KhGNMTA, Sv-12 Kh2NMFA welding wires and NF-18 M, FZ-16 A welding fluxes, is under study. Experimental studies are carried out using three heats with the chemical composition meeting the specifications. Weld specimens 100-200 mm thick are subjected to tempering according various regimes to induce the embrittlement and simulate mechanical properties (yield strength and ductile-brittle transition temperature) corresponding to those at the end of service life under neutron radiation effect. Base metal and weld properties are compared. The wide scatter is noted for experimental data on fracture toughness temperature dependences. A possibility to use the dependence of K Ia = f (T-T k ) for determining the crack arrest fracture toughness is discussed taking in account that K Ia is a stress intensity factor calculated within the frame of static fracture mechanics [ru

The effect of the PWR secondary circuit water chemistry on erosion corrosion

International Nuclear Information System (INIS)

Kaplan, J.

1993-07-01

The secondary circuit of WWER-440 and WWER-1000 reactors is described. The causes of erosion corrosion are outlined, and the effects of the physical properties and chemical composition of water are discussed with emphasis on specific conductivity and concentrations of oxygen, ammonia, iron, sodium, silicon and organics. Described are corrective actions to eliminate the deviations from the normal state during reactor power reduction or reactor shutdown. (J.B.)

Report of the review of the safety improvement programme for South Ukraine NPP units 1 and 2 and to identify the safety issues of ''small series'' WWER-1000 NPPs. South Ukraine Yuzhnoukrainsk, Nikolaev Region Ukraine, 8 to 19 July 1996. Draft

International Nuclear Information System (INIS)

Bastin, S.; Hoehn, J.; Lin, C.; Taylor, R.; Benitez, F.; Dale, H.; Mueller, B.; Rieg, C.Y.

1996-10-01

According to the Ukrainian request the purpose of the IAEA experts' mission was to review the safety improvement programme for South Ukraine NPP Units 1 and 2 in order to advise on the completeness and adequacy of safety improvements implemented and/or proposed. Another purpose of the mission was to identify major design and operational deficiencies as a basis to compile a consolidated list of generic safety issues for the units of the 'small series'' of WWER-1000 reactors (''Issue Book for ''small series'' WWER-1000 NPPs). Conclusions and recommendations from the IAEA mission are based on the combined expertise of the international group of experts who composed the team. They are intended to assist national authorities and plant operators who have the sole responsibilities for the regulation and safe operation. tabs

Researches of WWER fuel rods behaviour under RIA accident conditions

International Nuclear Information System (INIS)

Nechaeva, O.; Medvedev, A.; Novikov, V.; Salatov, A.

2003-01-01

Unirradiated fuel rod and refabricated fuel rod tests in the BIGR as well as acceptance criteria proving absence of fragmentation and the settlement modeling of refabricated fuel rods thermomechanical behavior in the BIGR-tests using RAPTA-5 code are discussed in this paper. The behaviour of WWER type simulators with E110 and E635 cladding was researched at the BIGR reactor under power pulse conditions simulating reactivity initiated accident. The results of the tests in four variants of experimental conditions are submitted. The behaviour of 12 WWER type refabricated fuel rods was researched in the BIGR reactor under power pulse conditions simulating reactivity initiated accident: burnup 48 and 60 MWd/kgU, pulse width 3 ms, peak fuel enthalpy 115-190 cal/g. The program of future tests in the research reactor MIR with high burnup fuel rod (up to 70 MWd/kgU) under conditions simulating design RIA in WWER-1000 is presented

Modeling of coherent heat and mass-exchange phenomena for a specter of primary circuit leaks in a NPP with WWER-1000 type reactor

International Nuclear Information System (INIS)

Stanev, I.; Mladenova, S.; Hadjiev, V.

2004-01-01

Subject of study are the inter-relations between the primary leak parameters, the containment pressure and the functioning of the WWER-1000/V320 plant systems. The model includes systems for normal operation and safety systems, which are actuated in the initial stage of the accident. The studied specter of primary leaks includes diameters from 10 to 60 mm. The model is based on the design features of unit 5 in NPP Kozloduy. This paper presents a fragment of the work, performed jointly by Atoma Consult Ltd and NPP Kozloduy Plc on the validation of the symptom oriented emergency operation procedures for units 5 and 6 in NPP Kozloduy. (authors)

Co-ordinated research programme on benchmark study for the seismic analysis and testing of WWER-type nuclear power plants. V. 2B. General material: codes, standards, criteria. Working material

International Nuclear Information System (INIS)

1999-01-01

In August 1991, following the SMiRT-11 Conference in Tokyo, a Technical Committee Meeting was held on the 'Seismic safety issues relating to existing NPPs'. The Proceedings of this TCM was subsequently compiled in an IAEA Working Material. One of the main recommendations of this TCM, called for the harmonization of criteria and methods used in Member States in seismic reassessment and upgrading of existing NPPs. Twenty four institutions from thirteen countries participated in the CRP named 'Benchmark study for the seismic analysis and testing of WWER type NPPs'. Two types of WWER reactors (WWER-1000 and WWER-440/213) selected for benchmarking. Kozloduy NPP Units 5/6 and Paks NPP represented these respectively as prototypes. Consistent with the recommendations of the TCM and the working paper prepared by the subsequent Consultants' Meeting, the focal activity of the CRP was the benchmarking exercises. A similar methodology was followed both for Paks NPP and Kozloduy NPP Unit 5. Firstly, the NPP (mainly the reactor building) was tested using a blast loading generated by a series of explosions from buried TNT charges. Records from this test were obtained at several free field locations (both downhole and surface), foundation mat, various elevations of structures as well as some tanks and the stack. Then the benchmark participants were provided with structural drawings, soil data and the free field record of the blast experiment. Their task was to make a blind prediction of the response at preselected locations. The analytical results from these participants were then compared with the results from the test. Although the benchmarking exercises constituted the focus of the CRP, there were many other interesting problems related to the seismic safety of WWER type NPPs which were addressed by the participants. These involved generic studies, i.e. codes and standards used in original WWER designs and their comparison with current international practice; seismic analysis

Maintenance of nuclear power plants

International Nuclear Information System (INIS)

Lashgari, Farbod.

1995-01-01

This paper is about maintenance of nuclear power plants. In part one, the outage management of nuclear power plants has described. Meaning of the outage and objectives of outage management is given in introduction. The necessity of a long-term outage strategy is shown in chapter one. The main parts of an outage are as follows: Planning; Preparation; Execution, Each of them and also post-outage review have been explained in the followed chapters. Part two deals with technical details of main primary components of nuclear power plant type WWER. After an introduction about WWER reactors, in each chapter first the general and detailed description of main primary components has given and then their maintenance schedules and procedures. Chapter about reactor and steam generator is related to both types of WWER-440 and WWER-1000, but chapter about reactor coolant pump has specified to WWER-1000 to be more in details.(author)

Results of post-irradiation examination of WWER fuel assembly structural components made of E110 and E635 alloys

International Nuclear Information System (INIS)

Smirnov, A.; Markov, D.; Smirnov, V.; Polenok, V.; Ivashchenko, A.; Strozhuk, A.

2006-01-01

The paper presents the main examination results on the condition of fuel rods claddings, guide tubes and spacer grids of the WWER FA made of E110 and E635 alloys operated under standard operating conditions. The paper is based on the data obtained during the examination of 28 WWER-1000 FA and 12 WWER-400 FA. E110 alloy is shown to be suitable material for the WWER fuel rod claddings under the normal operating conditions. E635 alloy is attractive to manufacturing of the skeleton components. The currently used combination (E110 as a material of fuel rods claddings and E635 - as a material of the skeleton components) is the optimal solution for the WWER fuel assembly because the advantages of the both alloys are used. (authors)

Results of trial operation of new generation assemblies with improved vibration stability for WWER-440 reactors of V-230 and V-213 plants

International Nuclear Information System (INIS)

Vasilchenko, I.; Lushin, V.; Shumeev, A.

2006-01-01

The main task in developing a fuel design of new generation for WWER-440 power units (particularly for power units of V-213 type) is to increase the effectiveness of fuel utilization. For this purpose the following design solutions were realized: 1) increase of fuel loading (increase of fuel stack in a fuel rod); 2) optimization of the water-uranium relation (at the cost of some decrease of outside diameter of a fuel rod from 9,1 mm to 9,07 mm and increase of fuel rod pitch in a bundle from 12,2 mm up to 12,3 mm); 3) decrease of harmful absorption of neutrons (due to decrease of hafnium content in zirconium materials from 0,05 % to 0,01 % and decrease of zirconium in transition to thickness of FA casing of ERC assembly - 1,5 mm). The parallel task is to increase vibration stability of fuel assemblies based on the verification and justification of the following technical solutions: 1)improvement of vibration stability due to SG rearrangement along the fuel rod bundle height and increasement of height of the first three grids along the course of coolant flow; 2) decreasement of backlashes in the assembly 'fuel rod - support grid' due to introduction of a new elastic tip of fuel rods; 3) introduction of a stiffening rib under the support grid and attachment of the central tube in the support grid by welding; 4) introduction of special sleeve in the protective grid, which permits to fasten a bundle against radial displacements in its upper part; 5) introduction of slots, located at different height marks of the central tube, permits to exclude distortion and destruction of spacing grids as a result of increase of fuel rod temperature; 6) installation of filters at the inlet. According to design considerations with due regard for statistics of fuel assemblies damage, the filters will be mounted at the working assembly (WA) inlet. In new generation fuel assemblies, the problem of decrease of local flash-up of neutrons in the WA peripheral fuel rods, surrounding the CPS

Mathematical models in nuclear safety and radiation protection of nuclear energy

International Nuclear Information System (INIS)

1993-01-01

This collection of papers contains the full texts of 33 reports presented at the Seminar, all of which are indexed and abstracted separately for the INIS database. The topics of the reports cover the mathematical models and computer codes for risk analysis, reactor reliability simulating, safety-related benchmarks, thermohydraulic studies, reactor kinetics, hypothetical accidents and their radiological consequences, etc. The investigations refer mainly to WWER-440 and WWER-1000 type reactors of the Kozloduy NPP

FERONIA-CZ/PHARE Progress Report, January 1997 - December 1997

International Nuclear Information System (INIS)

Lassmann, K.; Laar, J. van de; Miasnikov, A.; Svoboda, R.; Valach, M.

1998-02-01

The report describes work performed within the programme 'Assistance to the State Office for Nuclear Safety of the Czech Republic by European Institute for Transuranium Elements Karlsruhe in Performing Fuel Rod Thermo-Mechanical Behaviour Analyses for the licensing process support, FERONIA (acronym for Fuel Rod Modelling and Performance)'. The main objective is a reliable prediction of fuel performance at the Temelin WWER-1000 units and Dukovany WWER-440 units. The TRANSURANUS code was employed

Co-ordinated research programme on benchmark study for the seismic analysis and testing of WWER-type nuclear power plants. V. 5C. Experience data. Working material

International Nuclear Information System (INIS)

1999-01-01

In August 1991, following the SMiRT-11 Conference in Tokyo, a Technical Committee Meeting was held on the 'Seismic safety issues relating to existing NPPs'. The Proceedings of this TCM was subsequently compiled in an IAEA Working Material. One of the main recommendations of this TCM, called for the harmonization of criteria and methods used in Member States in seismic reassessment and upgrading of existing NPPs. Twenty four institutions from thirteen countries participated in the CRP named 'Benchmark study for the seismic analysis and testing of WWER type NPPs'. Two types of WWER reactors (WWER-1000 and WWER-440/213) selected for benchmarking. Kozloduy NPP Units 5/6 and Paks NPP represented these respectively as prototypes. Consistent with the recommendations of the TCM and the working paper prepared by the subsequent Consultants' Meeting, the focal activity of the CRP was the benchmarking exercises. A similar methodology was followed both for Paks NPP and Kozloduy NPP Unit 5. Firstly, the NPP (mainly the reactor building) was tested using a blast loading generated by a series of explosions from buried TNT charges. Records from this test were obtained at several free field locations (both downhole and surface), foundation mat, various elevations of structures as well as some tanks and the stack. Then the benchmark participants were provided with structural drawings, soil data and the free field record of the blast experiment. Their task was to make a blind prediction of the response at preselected locations. The analytical results from these participants were then compared with the results from the test. Although the benchmarking exercises constituted the focus of the CRP, there were many other interesting problems related to the seismic safety of WWER type NPPs which were addressed by the participants. These involved generic studies, i.e. codes and standards used in original WWER designs and their comparison with current international practice; seismic analysis

Study of accelerated unit unloading mode initiated by turbine feed pump trip with TVSA fuel assemblies operation in WWER-1000

International Nuclear Information System (INIS)

Borysenko, V.I.; Kadenko, I.N.; Samoilenko, D.V.

2012-01-01

This paper provides the study results of accelerated unit unloading mode (AUU) initiated at WWER-1000 unit operated at 100 % power and its expediency in the event of single Turbo Feed Pump (TFP) failure. Modeling was performed using an advanced calculation code RELAP/SCDAPSIM/Mod3.4 and relevant model for KhNPP Unit No. 2. As the study shows, SCRAM cannot be prevented in case of failure of 3 main circulation pumps due to steam generators (SG) level drop. Based on the results obtained, it is reasonably justified to allow SCRAM signal instead of AUU activation in case of single TFP failure at power level more than 90 % of N n om. This will provide more sparing temperature modes for fuel assemblies and equipment, as well as prevent additional thermal cycling loads and violation of safe operation limits as SG water levels

Comparison calculations of WWER-1000 fuel assemblies by using the MCNP 4.2 a KASSETA codes

International Nuclear Information System (INIS)

Trgina, M.

1993-12-01

The power multiplication and distribution factors are compared for various geometries and material configurations of WWER-1000 fuel assemblies. The calculations were performed in 2 ways: (i) using nuclear data, employing older and current data collections, and (ii) using the author's own model based on the KASSETA code. The comparison code MCNP 4.2 is described, intended for computerized simulation of the transport of neutrons, photons and electrons. This code uses its own cross section library. The methodology is outlined and a specification of the Monte Carlo method employed is given. The use of the refined data library gave rise to appreciable deviations of the multiplication factors in all variants. The use of the older data library led to identical criticality results for the variant with water holes. For inserted absorbers the discrepancies in criticality and in power distribution data are appreciable. The marked disagreement between the results of application of the MCNP 4.2 and KASSETA codes for the variants with inserted control elements is indicative of inappropriateness of the approximation procedure in the latter code. (J.B.). 2 tabs., 11 figs., 11 refs

Effect of burnup history by moderator density on neutron-physical characteristics of WWER-1000 core

International Nuclear Information System (INIS)

Ovdiienko, I.; Kuchin, A.; Khalimonchuk, V.; Ieremenko, M.

2011-01-01

Results of assessment of burnup history effect by moderator density on neutron physical characteristics of WWER-1000 core are presented on example of stationary fuel loading with Russian design fuel assembly TWSA and AER benchmark for Khmelnitsky NPP that was proposed by TUV and SSTC NRC at nineteenth symposium. Assessment was performed by DYN3D code and cross section library sets generated by HELIOS code. Burnup history was taken into account by preparing of numerous cross section sets with different isotopic composition each of which was obtained by burning under different moderator density. For analysis of history effect 20 cross section sets were prepared for each fuel assembly corresponded to each of 20 axial layers of reactor core model for DYN3D code. Four fuel cycles were modeled both for stationary fuel loading with TWSA and AER benchmark for Khmelnitsky NPP to obtain steady value of error due to neglect of burnup history effect. Main attention of study was paid to effect of burnup history by moderator density to axial power distribution. Results of study for AER benchmark were compared with experimental values of axial power distribution for fuel assemblies of first, second, third and fourth year operation. (Authors)

Contributions of Modranska potrubni a.s. to the safety improvement of piping systems and valves of NPS type VVER 440 and VVER 1000

International Nuclear Information System (INIS)

Slach, J.

2004-01-01

The following activities are described: (i) Installation of pipe whip restraints on piping for high pressure and temperature steam and feed piping; (ii) Installation of air receivers for quick-acting valves with air actuator on VVER 440 units at the Jaslovske Bohunice V2 NPP; (iii) Replacement of the technical water distribution system material in the reactor hall of the Temelin VVER 1000 units; Installation of measuring nozzles on main steam piping DN 600 at the Temelin VVER 1000 units. (P.A.)

In-service diagnostics of main circulating circuit pipes of WWER nuclear power plants

International Nuclear Information System (INIS)

Svoboda, V.; Merta, J.; Merta, V.

1982-01-01

The application is discussed of the acoustic emission method for testing the integrity of the components of the main circulating circuit of the WWER 440 nuclear power plant. A description is given of the main circulating circuit and a stress analysis on the basis of strength computations considering operating modes is presented. An analysis is also presented of the possible damage of the pipe material as related to the application of the acoustic emission method for in-service inspection of the pipes. Certain practical problems of application are discussed. (author)

Experiments on simulation of coolant mixing in fuel assembly head and core exit channel of WWER-440 reactor

International Nuclear Information System (INIS)

Kobzar, L.L; Oleksyuk, D.A.

2006-01-01

RRC 'Kurchatov Institute' has performed coolant mixing investigation in a head of a full-size simulator of WWER-440 fuel assembly. The experiments were focused on obtaining the data important for investigating the trends in temperature difference between the value registered by a ICIS thermocouple and the value of average temperature. The completed experiments ensure representative of configuration simulation by reproducing every construction peculiar feature of flow part of fuel assembly in the domain between the lower spacing grid and thermocouple location, and also by slightly modified fuel assembly regular elements (or analogues thereof). For the purpose of effectiveness of coolant mixing assessment within the head cross section of FA simulator, we measured coolant temperature distribution both in the place where coolant flow leaves the rod bundle simulator (in 39 data points along the cross section) and in the cross section location of regular ICIS thermocouple simulator (30 data points). The testing was conducted with pressure of (90 - 95) bar, mass coolant flow rates up to 2000 kg/(m 2 .s), temperature of coolant heating in 'hot' parts of the bundle up to 35.. and differences between coolant temperature extremes measured in rod bundle simulator outlet up to 20... Temperature fields were registered in 63 conditions that differ in coolant flow and inlet coolant temperature, electrical heating rate of FA simulator, and radial coolant distribution. In certain registered conditions we simulated coolant leakage to the space between the fuel assemblies. The received test data may be important both for investigation of dependencies between the coolant temperature in regular thermocouple location or average outlet temperature in assembly head, and for validation of CFD codes or subchannel codes (Authors)

Lessons learned from the computational simulation of thermomechanical behaviour of the WWER-1000 reactor cores: FA development and its implantation into the Balakovo NPP unit 1

International Nuclear Information System (INIS)

Troyanov, V.; Likhatchev, Y.; Folomeev, V.; Demishonkov, A.

2003-01-01

The fuel assembly is forced under operation conditions by weight and hydraulic force; hold-down force; contact transversal forces; non-uniform thermal and neutron fields; thermomechanical forces in the fuel assembly multirod structure. The fuel assembly bowing has been investigated in this work. The objective of the study is to recommend the optimal design for fuel assemblies. Calculations are made using the code TEREMOK. A new generation fuel assemblies for WWER-1000 named FA-2 are suggested. The performance of the FA- 2 has been studied. The theoretical approach and the calculation technique have been verified

On the advisability of nuclear power plant construction and some solutions on their safety increase

International Nuclear Information System (INIS)

Sokolov, I.N.

1989-01-01

Neccesity in a further development of nuclear power in the USSR is proved. Specific features of layouts of nuclear heat supplying plants with increased safety including WWER-440, WWER-1000 and VK-50 reactors are considered. It is stressed that even under the most incredible accidents referring to the class of hypothetic ones, radioactive effect on the population, according to evaluations by experts, whould be much lower than maximum admissible one according to the existing standards