Restoration principles and criteria: superfund program policy for cleanup at radiation contaminated sites

International Nuclear Information System (INIS)

Walker, Stuart

2006-01-01

The Environmental Protection Agency (EPA) Office of Superfund Remediation and Technology Innovation (OSRTI) is responsible for implementing the long-term (non-emergency) portion of a key U.S. law regulating cleanup: the Comprehensive Environmental Response, Compensation and Liability Act, CERCLA, nicknamed 'Superfund'. The purpose of the Superfund program is to protect human health and the environment over the long term from releases or potential releases of hazardous substances from abandoned or uncontrolled hazardous waste sites. The focus of this paper is on Superfund, including how radiation is addressed by the Superfund program. This paper provides a brief overview of the approach used by EPA to conduct Superfund cleanups at contaminated sites, including those that are contaminated with radionuclides, to ensure protection of human health and the environment. The paper addresses how EPA Superfund determines if a site poses a risk to human health and the framework used to determine cleanup levels. The theme emphasized throughout the paper is that within the Superfund remediation framework, radioactive contamination is dealt with in a consistent manner as with chemical contamination, except to account for the technical differences between radionuclides and chemicals. This consistency is important since at every radioactively contaminated site being addressed under Superfund's primary program for long-term cleanup, the National Priorities List (NPL), chemical contamination is also present. (author)

SITE COMPREHENSIVE LISTING (CERCLIS) (Superfund)

Data.gov (United States)

U.S. Environmental Protection Agency — The Comprehensive Environmental Response, Compensation and Liability Information System (CERCLIS) (Superfund) Public Access Database contains a selected set of...

Restoration principles and criteria: Superfund programme policy for cleanup at radiation contaminated sites

International Nuclear Information System (INIS)

Shapiro, M.

2000-01-01

The Environmental Protection Agency (EPA) Office of Solid Waste and Emergency Response is responsible for implementing two key US laws regulating waste management and cleanup: the Resource Conservation and Recovery Act, and the Comprehensive Environmental Response, Compensation and Liability Act, CERCLA, nicknamed ''Superfund''. The purpose of the Superfund programme is to protect human health and the environment over the long term from releases or potential releases of hazardous substances from abandoned or uncontrolled hazardous waste sites. The focus of this paper is on Superfund, including how radiation is addressed by the Superfund programme. This paper provides a brief overview of the approach used by EPA to conduct Superfund cleanups at contaminated sites, including those that are contaminated with radionuclides, to ensure protection of human health and the environment. The paper addresses how EPA Superfund determines if a site poses a risk to human health and the framework used to determine cleanup levels. The theme emphasized throughout the paper is that within the Superfund remediation framework, radioactive contamination is dealt with in the identical way as chemical contamination. (author)

New photocatalytic process provides 99.9+% reduction of VOC at Superfund site

Energy Technology Data Exchange (ETDEWEB)

Anon.

1999-03-01

A new photocatalytic process, dubbed the A-I-R-2000 Process, is described. The process is said to offer marked economic advantages, while providing consistent 99.9+% reduction of volatile organic compounds (VOCs) from soil vapours and groundwater at the Stamina Mills Superfund site in North Smithfield, Rhode Island. The A-I-R-2000 process has been developed by KSE Inc., of Amherst, Massachusetts, and has been licensed exclusively worldwide to Trojan Technologies, Inc., of London, Ontario. The process consists essentially of adsorption of VOCs onto a UV light-activated proprietary catalysts, for breakdown to carbon dioxide and water, and also to hydrochloric acid and a small amount of chlorine gas when the VOCs are chlorinated. With a maximum internal operating temperature of 125 degrees F, it is a low-energy system when compared to other catalytic technologies that feature thermal catalytic equipment. 1 photo.

75 FR 49414 - Cooperative Agreements and Superfund State Contracts for Superfund Response Actions

Science.gov (United States)

2010-08-13

...-0276. FOR FURTHER INFORMATION CONTACT: Angelo Carasea, Assessment and Remediation Division, Office of Superfund Remediation and Technology Innovation, (5204P), Environmental Protection Agency, 1200 Pennsylvania... funds to a State, political subdivision, or Indian Tribe that assumes responsibility as the lead or...

FUSRAP adapts to the amendments of Superfund

International Nuclear Information System (INIS)

Atkin, R.G.; Liedle, S.D.; Clemens, B.W.

1988-01-01

With the promulgation of the Superfund Amendments and Reauthorization Act (SARA) federal facilities were required to comply with the Comprehensive Environmental Response Compensation and Liability Act (CERCLA) in the same manner as any non-government entity. This situation presented challenges for the Department of Energy (DOE) and other federal agencies involved in remedial action work because of the requirements under SARA that overlap other laws requiring DOE compliance, e.g., the National Environmental Policy Act (NEPA). This paper outlines options developed to comply with CERCLA and NEPA as part of an active, multi-site remedial action program. The program, the Formerly Utilized Sites Remedial Action Program (FUSRAP), was developed to identify, clean up, or control sites containing residual radioactive contamination resulting from the nation's early development of nuclear power. During the Manhattan Project, uranium was extracted from domestic and foreign ores and resulted in mill concentrates, purified metals, and waste products that were transported for use or disposal at other locations. Figure 1 shows the steps for producing uranium metal during the Manhattan Project. As a result of these activities materials equipment, buildings, and land became contaminated, primarily with naturally occurring radionuclides. Currently, FUSRAP includes 29 sites; three are on the Environmental Protection Agency's (EPA's) National Priorities List (NPL) of hazardous waste sites

Superfund TIO videos: Set B. Financial management and SCAP. Part 8. Audio-Visual

International Nuclear Information System (INIS)

1990-01-01

The videotape covers various aspects of financial management for the Superfund Program. The importance of effective financial management and execution is discussed. The objectives and definitions of the Superfund Comprehensive Accomplishment Plan (SCAP) and the roles and responsibilities of Superfund personnel in the SCAP process are covered

Feasibility study for the United Heckathorn Superfund Site, Richmond, California

Energy Technology Data Exchange (ETDEWEB)

Lincoff, A.H. [US Environmental Protection Agency, San Francisco, CA (United States). Region IX; Costan, G.P.; Montgomery, M.S.; White, P.J. [Pacific Northwest Lab., Richland, WA (United States)

1994-07-01

The United Heckathom Superfund Site in Richmond, California, was used to formulate pesticides from approximately 1947 to 1966. Soils at the site and sediments in the harbor were contaminated with various chlorinated pesticides, primarily DDT, as a result of these activities. The US Environmental Protection Agency listed the site on the Superfund National Priorities List in 1990. This document is part of the Remedial Investigation and Feasibility Study phase of the Superfund response, which will provide the basis for selection of a final remedy that will protect human health and the environment and achieve compliance with federal and state envirorunental laws.

Feasibility study for the United Heckathorn Superfund Site, Richmond, California

International Nuclear Information System (INIS)

Lincoff, A.H.

1994-07-01

The United Heckathom Superfund Site in Richmond, California, was used to formulate pesticides from approximately 1947 to 1966. Soils at the site and sediments in the harbor were contaminated with various chlorinated pesticides, primarily DDT, as a result of these activities. The US Environmental Protection Agency listed the site on the Superfund National Priorities List in 1990. This document is part of the Remedial Investigation and Feasibility Study phase of the Superfund response, which will provide the basis for selection of a final remedy that will protect human health and the environment and achieve compliance with federal and state envirorunental laws

SUPERFUND TREATABILITY CLEARINGHOUSE: BDAT FOR SOLIDIFICATION/STABILIZATION TECHNOLOGY FOR SUPERFUND SOILS (DRAFT FINAL REPORT)

Science.gov (United States)

This report evaluates the performance of solidification as a method for treating solids from Superfund sites. Tests were conducted on four different artificially contaminated soils which are representative of soils found at the sites. Contaminated soils were solidified us...

Superfund Site Information - Site Sampling Data

Data.gov (United States)

U.S. Environmental Protection Agency — This asset includes Superfund site-specific sampling information including location of samples, types of samples, and analytical chemistry characteristics of...

78 FR 14543 - Ward Transformer Superfund Site; Raleigh, Wake County, NC; Notice of Settlement

Science.gov (United States)

2013-03-06

... ENVIRONMENTAL PROTECTION AGENCY [FRL 9788-2; CERCLA-04-2013-3754] Ward Transformer Superfund Site... Ward Transformer Superfund Site located in Raleigh, Wake County, North Carolina. Under the terms of the.... Submit your comments by Site name Ward Transformer Superfund Site by one of the following methods: [[Page...

Cleanups In My Community (CIMC) - Base Realignment and Closure (BRAC) Superfund Sites, National Layer

Science.gov (United States)

This data layer provides access to Base Realignment and Closure (BRAC) Superfund Sites as part of the CIMC web service. EPA works with DoD to facilitate the reuse and redevelopment of BRAC federal properties. When the BRAC program began in the early 1990s, EPA worked with DoD and the states to identify uncontaminated areas and these parcels were immediately made available for reuse. Since then EPA has worked with DoD to clean up the contaminated portions of bases. These are usually parcels that were training ranges, landfills, maintenance facilities and other past waste-disposal areas. Superfund is a program administered by the EPA to locate, investigate, and clean up worst hazardous waste sites throughout the United States. EPA administers the Superfund program in cooperation with individual states and tribal governments. These sites include abandoned warehouses, manufacturing facilities, processing plants, and landfills - the key word here being abandoned.This data layer shows Superfund Sites that are located at BRAC Federal Facilities. Additional Superfund sites and other BRAC sites (those that are not Superfund sites) are included in other data layers as part of this web service.BRAC Superfund Sites shown in this web service are derived from the epa.gov website and include links to the relevant web pages within the attribute table. Data about BRAC Superfund Sites are located on their own EPA web pages, and CIMC links to those pages. The CIMC web service

A method for estimating the local area economic damages of Superfund waste sites

International Nuclear Information System (INIS)

Walker, D.R.

1992-01-01

National Priority List (NPL) sites, or more commonly called Superfund sites, are hazardous waste sites (HWS) deemed by the Environmental Protection Agency (EPA) to impose the greatest risks to human health or welfare or to the environment. HWS are placed and ranked for cleanup on the NPL based on a score derived from the Hazard Ranking System (HRS), which is a scientific assessment of the health and environmental risks posed by HWS. A concern of the HRS is that the rank of sites is not based on benefit-cost analysis. The main objective of this dissertation is to develop a method for estimating the local area economic damages associated with Superfund waste sites. Secondarily, the model is used to derive county-level damage estimates for use in ranking the county level damages from Superfund sites. The conceptual model used to describe the damages associated with Superfund sites is a household-firm location decision model. In this model assumes that households and firms make their location choice based on the local level of wages, rents and amenities. The model was empirically implemented using 1980 census microdata on households and workers in 253 counties across the US. The household sample includes data on the value and structural characteristics of homes. The worker sample includes the annual earnings of workers and a vector worker attributes. The microdata was combined with county level amenity data, including the number of Superfund sites. The hedonic pricing technique was used to estimate the effect of Superfund sites on average annual wages per household and on monthly expenditures on housing. The results show that Superfund sites impose statistically significant damages on households. The annual county damages from Superfund sites for a sample of 151 counties was over 14 billion dollars. The ranking of counties using the damage estimates is correlated with the rank of counties using the HRS

78 FR 23563 - LWD, Inc. Superfund Site; Calvert City, Marshall County, Kentucky; Notice of Settlement

Science.gov (United States)

2013-04-19

... ENVIRONMENTAL PROTECTION AGENCY [FRL-9805-2; CERCLA-04-2013-3751] LWD, Inc. Superfund Site... costs concerning the LWD, Inc., Superfund Site located in Calvert City, Marshall County, Kentucky. The... V. Painter. Submit your comments by Site name LWD, Inc., Superfund Site by one of the following...

SITE COMPREHENSIVE LISTING (CERCLIS) (Superfund) - NPL Sites

Data.gov (United States)

U.S. Environmental Protection Agency — National Priorities List (NPL) Sites - The Comprehensive Environmental Response, Compensation and Liability Information System (CERCLIS) (Superfund) Public Access...

Superfund Sites as Anti-landscapes

DEFF Research Database (Denmark)

Nye, David

2017-01-01

Americans have used a range of narratives to make sense of their settlement and use of natural resources. This article focuses on narratives of environmental degradation after the United States passed legislation mandating the cleanup of toxic sites and provided a Superfund for that purpose. Thre...

CERCLIS (Superfund) ASCII Text Format - CPAD Database

Data.gov (United States)

U.S. Environmental Protection Agency — The Comprehensive Environmental Response, Compensation and Liability Information System (CERCLIS) (Superfund) Public Access Database (CPAD) contains a selected set...

Cleanups In My Community (CIMC) - Superfund National Priority List (NPL) Sites, National Layer

Data.gov (United States)

U.S. Environmental Protection Agency — This data layer provides access to Superfund National Priority List Sites as part of the CIMC web service. Superfund is a program administered by the EPA to locate,...

Remediation System Evaluation, McCormick and Baxter Superfund SiteRemediation System Evaluation, McCormick and Baxter Superfund Site

Science.gov (United States)

The McCormick and Baxter Creosoting Company, Portland Plant, Superfund Site is located adjacent tothe Willamette River in Portland, Oregon and addresses contamination of soil, groundwater, and riversediments stemming from creosoting operations...

Superfund National Priority List (NPL) Site Boundaries

Data.gov (United States)

U.S. Environmental Protection Agency — A set of site boundaries for each site in EPA Region 1 (Connecticut, Maine, Massachusetts, New Hampshire, Rhode Island, and Vermont) on EPA's Superfund National...

U.S. EPA Superfund Program's Policy for Community Involvement at Radioactively Contaminated Sites

International Nuclear Information System (INIS)

Carey, Pat; Walker, Stuart

2008-01-01

This paper describes the Superfund program's statutory requirements for community involvement. It also discusses the efforts the Superfund program has made that go beyond these statutory requirements to involve communities. The Environmental Protection Agency (EPA) implements the Superfund program under the authority of the Comprehensive Environmental Response, Compensation, and Liability Act of 1980 (CERCLA), as amended by the Superfund Amendments and Reauthorization Act of 1986 (SARA). From the beginning of the Superfund program, Congress envisioned a role for communities. This role has evolved and expanded during the implementation of the Superfund program. Initially, the CERCLA statute had community involvement requirements designed to inform surrounding communities of the work being done at a site. CERCLA's provisions required 1) development of a community relations plan for each site, 2) establishment of information repositories near each site where all publicly available materials related to the site would be accessible for public inspection, 3) opportunities for the public to comment on the proposed remedy for each site and 4) development of a responsiveness summary responding to all significant comments received on the proposed remedy. In recognition of the need for people living near Superfund sites to be well-informed and involved with decisions concerning sites in their communities, SARA expanded Superfund's community involvement activities in 1986. SARA provided the authority to award Technical Assistance Grants (TAGs) to local communities enabling them to hire independent technical advisors to assist them in understanding technical issues and data about the site. The Superfund Community Involvement Program has sought to effectively implement the statutory community involvement requirements, and to go beyond those requirements to find meaningful ways to involve citizens in the cleanup of sites in their communities. We've structured our program around

SITE COMPREHENSIVE LISTING (CERCLIS) (Superfund) - Non-NPL Sites

Data.gov (United States)

U.S. Environmental Protection Agency — Non-NPL Sites - The Comprehensive Environmental Response, Compensation and Liability Information System (CERCLIS) (Superfund) Public Access Database contains a...

In-Depth Case Studies of Superfund Reuse

Science.gov (United States)

SRI’s in-depth case studies explore Superfund reuse stories from start to finish. Their purpose is to see what redevelopment strategies worked, acknowledge reuse barriers and understand how communities overcame the barriers to create new reuse outcomes.

Human Health Toxicity Values in Superfund Risk Assessments

Science.gov (United States)

This memorandum revises the hierarchy of human health toxicity values generally recommended for use inr isk assessments, originally presented in Risk Assessment Guidance for Superfund Volume I, Part A.

SHIRCO PILOT-SCALE INFRARED INCINERATION SYSTEM AT THE ROSE TOWNSHIP DEMODE ROAD SUPERFUND SITE

Science.gov (United States)

Under the Superfund Innovative Technology Evaluation or SITE Program, an evaluation was made of the Shirco Pilot-Scale Infrared Incineration System during 17 separate test runs under varying operating conditions. The tests were conducted at the Demode Road Superfund site in Ros...

78 FR 729 - Ellman Battery Superfund Site; Orlando, Orange County, FL; Notice of Settlement

Science.gov (United States)

2013-01-04

... ENVIRONMENTAL PROTECTION AGENCY [FRL-9767-6; CERCLA-04-2012-3780] Ellman Battery Superfund Site; Orlando, Orange County, FL; Notice of Settlement AGENCY: Environmental Protection Agency (EPA). ACTION... Action at the Ellman Battery Superfund Site located in Orlando, Orange County, Florida. DATES: The Agency...

SITE COMPREHENSIVE LISTING (CERCLIS) - Contaminants at CERCLIS (Superfund) Sites

Data.gov (United States)

U.S. Environmental Protection Agency — Contaminants at Comprehensive Environmental Response, Compensation and Liability Information System (CERCLIS) (Superfund) Sites - The CERCLIS Public Access Database...

Report: Remedial Project Manager Turnover at Superfund Sites

Science.gov (United States)

Report #2001-M-000015, June 15, 2001. We determined that EPA Region III did not have formal procedures in place to mitigate continuity problems caused by turnover of EPA personnel in the Superfund program.

77 FR 16548 - Florida Petroleum Reprocessors Superfund Site; Davie, Broward County, FL; Notice of Settlements

Science.gov (United States)

2012-03-21

...-2012- 3766; CERCLA-04-2012-3765] Florida Petroleum Reprocessors Superfund Site; Davie, Broward County... costs concerning the Florida Petroleum Reprocessors Superfund Site located in Davie, Broward County.... Painter. Submit your comments by Site name Florida Petroleum Reprocessors by one of the following methods...

77 FR 11533 - Anniston PCB Superfund Site, Anniston, Calhoun County, Alabama; Notice of Amended Settlement

Science.gov (United States)

2012-02-27

... ENVIRONMENTAL PROTECTION AGENCY [CERCLA-04-2012-3763; FRL 9637-7] Anniston PCB Superfund Site... past response costs concerning the Anniston PCB Superfund Site located in Anniston, Calhoun County.... Submit your comments by Site name Anniston PCB by one of the following methods: www.epa.gov/region4...

Smart moves in superfund - revitalization one year later. Volume 1, Number 3, January 1993. Bulletin

International Nuclear Information System (INIS)

1993-01-01

The issue of the Smart Moves in Superfund bulletin series provides an update on the revitalization effort, highlighting National Priorities List (NPL) construction completions, accelerating cleanup, the Superfund Accelerated Cleanup Model, risk assessment/risk management, contracts management, enforcement policy/equity, interagency cooperation, public forms, and state meetings

Centredale Manor Superfund Site in Rhode Island included on EPA List of Targeted for Immediate Attention

Science.gov (United States)

Today, the U.S. Environmental Protection Agency released the list of Superfund sites that Administrator Pruitt has targeted for immediate and intense attention. The Centredale Manor Restoration Project superfund site is one of the 21 sites on the list.

Remediation System Evaluation, Douglas Road Landfill Superfund Site

Science.gov (United States)

The Douglas Road Landfill Superfund Site is located in St. Joseph County just north of Mishawaka,Indiana. The site consists of a 16-acre capped landfill located on an approximately 32-acre lot (includingthe land purchased in 1999 for a wetlands...

SITE COMPREHENSIVE LISTING (CERCLIS) (Superfund) - Responsible Parties at CERCLIS Sites

Data.gov (United States)

U.S. Environmental Protection Agency — Responsible Parties at CERCLIS Sites - The Comprehensive Environmental Response, Compensation and Liability Information System (CERCLIS) (Superfund) Public Access...

New York's new Superfund regulations: Implications for federal and other state programs

International Nuclear Information System (INIS)

Pavetto, C.S.; Rubinton, D.S.

1994-01-01

The need for cleaning up hazardous waste disposal sites was identified early in New York. In fact, New York's ''Superfund'' statute preceded the federal Superfund law thereby providing a model for CERCLA. Moreover, there are currently almost as many sites on New York's Registry of Inactive Hazardous Waste Disposal sites as there are sites on the National Priorities List. While New York's law served as a model for the federal CERCLA, CERCLA, in turn, has served as a model for other states' statutes. Similarly, lessons learned from the implementation of state Superfund statutes such as New York's can be instructive for those whose work involves dealing with CERCLA-type issues. This is because the problems associated with site restoration and cleanup, such as exceedingly complex site review and evaluation processes, high transaction costs, and difficulties in prioritizing sites for clean-up based upon the threat or risk of environmental harm, are universal

U.S. EPA Superfund Program's Policy for Community Involvement at Radioactively Contaminated Sites

International Nuclear Information System (INIS)

Martin, K.; Walker, St.

2009-01-01

This paper describes the EPA Superfund program's statutory requirements for community involvement. It also discusses the efforts the Superfund program has made that go beyond these statutory requirements to involve communities, and what lessons have been learned by EPA when trying to conduct meaningful community involvement at sites. In addition, it discusses tools that EPA has designed to specifically enhance community involvement at radioactively contaminated Superfund sites. In summary, the Superfund program devotes substantial resources to involving the local community in the site cleanup decision making process. We believe community involvement provides us with highly valuable information that must be available to carefully consider remedial alternatives at a site. We also find our employees enjoy their jobs more. Rather than fighting with an angry public they can work collaboratively to solve the problems created by the hazardous waste sites. We have learned the time and resources we devote at the beginning of a project to developing relationships with the local community, and learning about their issues and concerns is time and resources well spent. We believe the evidence shows this up-front investment helps us make better cleanup decisions, and avoids last minute efforts to work with a hostile community who feels left out of the decision-making process. (authors)

40 CFR 35.4040 - How many groups can receive a TAG at one Superfund site?

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 1 2010-07-01 2010-07-01 false How many groups can receive a TAG at one Superfund site? 35.4040 Section 35.4040 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Eligible? § 35.4040 How many groups can receive a TAG at one Superfund site? (a) Only one TAG may be...

“It’s a cosmetic world”

Directory of Open Access Journals (Sweden)

Didier Aubert

2011-04-01

Full Text Available When I called him in early February, fine art-documentary-advertising photographer Larry Fink was just returning from men’s fashion week in Milan. The occasion for the trip was an exhibit of his work in collaboration with one of his regular clients, Woolrich Woolen Mills. Fink had shot the clothing company’s catalogue several times, but this was a different project. Documentary pictures of the logging community he had taken in the 1980s were used as background for a fashion show evoking “Man ...

Strategy to Ensure Institutional Control Implementation at Superfund Sites

Science.gov (United States)

This document sets forth EPA’s strategy (Strategy) for ensuring that institutional controls (ICs) are successfully implemented at Superfund sites, with an emphasis on evaluating ICs at sites where all construction of all remedies is complete (construction complete sites).

Privacy Impact Assessment for the Enforcement Superfund Tracking System

Science.gov (United States)

This Enforcement Superfund Tracking System (ESTS) collects publicly available information from the California Secretary of State on businesses. Learn how this data is collected, how it will be used, access to the data, and the purpose of data collection.

78 FR 47317 - Ore Knob Mine Superfund Site; Laurel Springs, Ashe County, North Carolina; Notice of Settlement

Science.gov (United States)

2013-08-05

... ENVIRONMENTAL PROTECTION AGENCY [FRL-9843-3; CERCLA-04-2013-3759] Ore Knob Mine Superfund Site; Laurel Springs, Ashe County, North Carolina; Notice of Settlement AGENCY: Environmental Protection Agency... settlement with Herbert N. Francis concerning the Ore Knob Mine Superfund Site located in Laurel Springs...

EPA [Environmental Protection Agency] SITE [Superfund Innovative Technology Evaluation] program seeks technology proposals

International Nuclear Information System (INIS)

Anon.

1989-01-01

EPA will issue an RFP to initiate the SITE-005 solicitation for demonstration of technologies under the Superfund Innovative Technology Evaluation (SITE) Program. This portion of the SITE program offers a mechanism for conducting a joint technology demonstration between EPA and the private sector. The goal of the demonstration program is to provide an opportunity for developers to demonstrate the performance of their technologies on actual hazardous wastes at Superfund sites, and to provide accurate and reliable data on that performance. Technologies selected must be of commercial scale and provide solutions to problems encountered at Superfund Sites. Primary emphasis in the RFP is on technologies that address: treatment of mixed, low level radioactive wastes in soils and groundwater; treatment of soils and sludges contaminated with organics and/or inorganics, materials handling as a preliminary step to treatment or further processing, treatment trains designed to handle specific wastes, are in situ technologies, especially those processes providing alternatives to conventional groundwater pump and treat techniques

Superfund Removal Site Points, Region 9, 2012, US EPA Region 9

Data.gov (United States)

U.S. Environmental Protection Agency — Point geospatial dataset representing locations of CERCLA (Superfund) Removal sites. CERCLA (Comprehensive Environmental Response, Compensation, and Liability Act)...

DECISION ANALYSIS OF INCINERATION COSTS IN SUPERFUND SITE REMEDIATION

Science.gov (United States)

This study examines the decision-making process of the remedial design (RD) phase of on-site incineration projects conducted at Superfund sites. Decisions made during RD affect the cost and schedule of remedial action (RA). Decision analysis techniques are used to determine the...

Effect of the milling conditions on the degree of amorphization of selenium by milling in a planetary ball mill

International Nuclear Information System (INIS)

Ksiazek, K; Wacke, S; Gorecki, T; Gorecki, Cz

2007-01-01

The effect of the milling parameters (rotation speed of the milling device and duration of milling) on the phase composition of the products of milling of fully crystalline selenium has been investigated. The milling was conducted using a planetary micromill and the phase composition of the milling products was determined by differential thermal analysis. It has been found that ball milling leads to the partial amorphization of the starting crystalline material. The content of amorphous phase in the milling products depends, in a rather complicated way, on the milling parameters. At the milling parameters adopted in the present study, the milling product was never fully amorphous. The complicated way the milling parameters affect the content of amorphous phase in the milling products is a result of competition of two processes: amorphization due to deformation and refinement of grains of milled material and crystallization of the already produced amorphous material at the cost of heat evolved in the milling vial during the milling process

Optimization Review: Carson River Mercury Superfund Site, Carson City, Nevada

Science.gov (United States)

The Carson River Mercury Site (CRMS) (Figure 1) is located in northwest Nevada and was designated a Superfund site in 1990 because of elevated mercury concentrations observed in surface water, sediments and biota inhabiting the site.

Remediation System Evaluation, Savage Municipal Water Supply Superfund Site (PDF)

Science.gov (United States)

The Savage Municipal Water Supply Superfund Site, located on the western edge of Milford, New Hampshire, consists of a source area and an extended plume that is approximately 6,000 feet long and 2,500 feet wide.

Mining-Related Sediment and Soil Contamination in a Large Superfund Site: Characterization, Habitat Implications, and Remediation.

Science.gov (United States)

Juracek, K E; Drake, K D

2016-10-01

Historical mining activity (1850-1970) in the now inactive Tri-State Mining District provided an ongoing source of lead and zinc to the environment including the US Environmental Protection Agency Superfund site located in Cherokee County, southeast Kansas, USA. The resultant contamination adversely affected biota and caused human health problems and risks. Remediation in the Superfund site requires an understanding of the magnitude and extent of contamination. To provide some of the required information, a series of sediment and soil investigations were conducted in and near the Superfund site to characterize lead and zinc contamination in the aquatic and floodplain environments along the main-stem Spring River and its major tributaries. In the Superfund site, the most pronounced lead and zinc contamination, with concentrations that far exceed sediment quality guidelines associated with potential adverse biological effects, was measured for streambed sediments and floodplain soils located within or downstream from the most intensive mining-affected areas. Tributary streambeds and floodplains in affected areas are heavily contaminated with some sites having lead and zinc concentrations that are an order of magnitude (or more) greater than the sediment quality guidelines. For the main-stem Spring River, the streambed is contaminated but the floodplain is mostly uncontaminated. Measured lead and zinc concentrations in streambed sediments, lakebed sediments, and floodplain soils documented a persistence of the post-mining contamination on a decadal timescale. These results provide a basis for the prioritization, development, and implementation of plans to remediate contamination in the affected aquatic and floodplain environments within the Superfund site.

Mining-related sediment and soil contamination in a large Superfund site: Characterization, habitat implications, and remediation

Science.gov (United States)

Juracek, Kyle E.; Drake, K. D.

2016-01-01

Historical mining activity (1850–1970) in the now inactive Tri-State Mining District provided an ongoing source of lead and zinc to the environment including the US Environmental Protection Agency Superfund site located in Cherokee County, southeast Kansas, USA. The resultant contamination adversely affected biota and caused human health problems and risks. Remediation in the Superfund site requires an understanding of the magnitude and extent of contamination. To provide some of the required information, a series of sediment and soil investigations were conducted in and near the Superfund site to characterize lead and zinc contamination in the aquatic and floodplain environments along the main-stem Spring River and its major tributaries. In the Superfund site, the most pronounced lead and zinc contamination, with concentrations that far exceed sediment quality guidelines associated with potential adverse biological effects, was measured for streambed sediments and floodplain soils located within or downstream from the most intensive mining-affected areas. Tributary streambeds and floodplains in affected areas are heavily contaminated with some sites having lead and zinc concentrations that are an order of magnitude (or more) greater than the sediment quality guidelines. For the main-stem Spring River, the streambed is contaminated but the floodplain is mostly uncontaminated. Measured lead and zinc concentrations in streambed sediments, lakebed sediments, and floodplain soils documented a persistence of the post-mining contamination on a decadal timescale. These results provide a basis for the prioritization, development, and implementation of plans to remediate contamination in the affected aquatic and floodplain environments within the Superfund site.

Superfund XV conference proceedings. Volume 1

International Nuclear Information System (INIS)

Anon.

1994-01-01

This conference was held November 29--December 1, 1994 in Washington, D.C..The purpose of this conference was to provide a forum for exchange of state-of-the-art information on Superfund. Papers are included on the following topics: bioremediation; building decontamination; environmental policy issues; federal environmental restoration; groundwater remediation; innovative sampling and analytical technologies; laboratory methods; metals management; mixed wastes; PCB waste management; remediation technology and case studies; and risk assessment. Individual papers have been processed separately for inclusion in the appropriate data bases

Superfund Technology Evaluation Report: SITE Program Demonstration Test Shirco Pilot-Scale Infrared Incineration System at the Rose Township Demode Road Superfund Site Volume I

Science.gov (United States)

The Shirco Pilot-Scale Infrared Incineration System was evaluated during a series of seventeen test runs under varied operating conditions at the Demode Road Superfund Site located in Rose Township, Michigan. The tests sought to demonstrate the effectiveness of the unit and the t...

Diffusive flux of PAHs across sediment-water and water-air interfaces at urban superfund sites.

Science.gov (United States)

Minick, D James; Anderson, Kim A

2017-09-01

Superfund sites may be a source of polycyclic aromatic hydrocarbons (PAHs) to the surrounding environment. These sites can also act as PAH sinks from present-day anthropogenic activities, especially in urban locations. Understanding PAH transport across environmental compartments helps to define the relative contributions of these sources and is therefore important for informing remedial and management decisions. In the present study, paired passive samplers were co-deployed at sediment-water and water-air interfaces within the Portland Harbor Superfund Site and the McCormick and Baxter Superfund Site. These sites, located along the Willamette River (Portland, OR, USA), have PAH contamination from both legacy and modern sources. Diffusive flux calculations indicate that the Willamette River acts predominantly as a sink for low molecular weight PAHs from both the sediment and the air. The sediment was also predominantly a source of 4- and 5-ring PAHs to the river, and the river was a source of these same PAHs to the air, indicating that legacy pollution may be contributing to PAH exposure for residents of the Portland urban center. At the remediated McCormick and Baxter Superfund Site, flux measurements highlight locations within the sand and rock sediment cap where contaminant breakthrough is occurring. Environ Toxicol Chem 2017;36:2281-2289. © 2017 SETAC. © 2017 SETAC.

Electrochemical peroxidation of PCBs and VOCs in superfund site water and sediments

Energy Technology Data Exchange (ETDEWEB)

Scrudato, R.J.; Chiarenzelli, J.R. [SUNY, Oswego, NY (United States)

1996-12-31

An electrochemical peroxidation (ECP) process has been developed and used to degrade polychlorinated biphenyls (PCB) and volatile organic compounds (VOC)-contaminated water, sludge, and sediments at a New York State Federal and State Superfund Site. The process involves passing an oscillating low-amperage (<10 amps) current through steel electrodes immersed in an acidified water or sediment slurry into which hydrogen peroxide (<1,000 ppm) is added. The generated free radicals attack organic compounds, including organo-metallic complexes and refractory compounds including PCBs. PCB degradation ranged from about 30% to 80% in experiments involving Federal Superfund Site sediments; total PCBs were reduced by {approximately}97% to 68%, respectively, in water and slurry collected from a State Superfund subsurface storage tank. VOC bench-scale experiments involved chloroethane, 1,1-dichloroethane, dichloromethane, 1,1,1-trichloroethane, and acetone and after a 3-min ECP treatment, degradation ranged from >94% to about 99.9%. Results indicate the ECP is a viable process to degrade organic contaminants in water and sediment suspensions. Because the treated water suspensions are acidified, select trace metal sorbed to the particulates is solubilized and therefore can be segregated from the particulates, offering a process that simultaneously degrades organic contaminants and separates trace metals. 19 refs., 1 fig., 4 tabs.

Uranium milling costs

International Nuclear Information System (INIS)

Coleman, R.B.

1980-01-01

Basic process flowsheets are reviewed for conventional milling of US ores. Capital costs are presented for various mill capacities for one of the basic processes. Operating costs are shown for various mill capacities for all of the basic process flowsheets. The number of mills using, or planning to use, a particular process is reviewed. A summary of the estimated average milling costs for all operating US mills is shown

Ensuring the adequacy of cost share provisions in superfund state contracts. Directive

International Nuclear Information System (INIS)

1993-01-01

The memorandum requests regional offices to re-examine existing Superfund State Contracts (SSCs) for Fund-financed remedial actions to verify that they adequately reflect incurred and projected remedial action costs

Superfund at work: Hazardous waste cleanup efforts nationwide, spring 1993 (Radium Chemical Site profile, Queens, New York)

International Nuclear Information System (INIS)

1993-01-01

The Radium Chemical hazardous waste site in Queens, New York was contaminated with radium, posing a grave potential threat to the community. The US Environmental Protection Agency (EPA) used the Superfund program to design a long-term cleanup for the site using input from citizens and the business community. Superfund staff: Mobilized a quick cleanup action to remove 10,000 small containers of radium; Developed a streamlined approach to long-term cleanup; Secured the site to reduce the possibility of radiation exposure to the local residents; Cooperated with the community to design a well-organized emergency response plan; and Educated local citizens about site hazards, incorporating community concerns into the cleanup process. The Radium Chemical site is a clear example of EPA's effective management and problem-solving strategies at Superfund sites

Superfund fact sheet: The remedial program. Fact sheet

International Nuclear Information System (INIS)

1992-09-01

The fact sheet describes what various actions the EPA can take to clean up hazardous wastes sites. Explanations of how the criteria for environmental and public health risk assessment are determined and the role of state and local governments in site remediation are given. The fact sheet is one in a series providing reference information about Superfund issues and is intended for readers with no formal scientific training

Towards identifying the next generation of superfund and hazardous waste site contaminants

Science.gov (United States)

Ela, Wendell P.; Sedlak, David L.; Barlaz, Morton A.; Henry, Heather F.; Muir, Derek C.G.; Swackhamer, Deborah L.; Weber, Eric J.; Arnold, Robert G.; Ferguson, P. Lee; Field, Jennifer A.; Furlong, Edward T.; Giesy, John P.; Halden, Rolf U.; Henry, Tala; Hites, Ronald A.; Hornbuckle, Keri C.; Howard, Philip H.; Luthy, Richard G.; Meyer, Anita K.; Saez, A. Eduardo; vom Saal, Frederick S.; Vulpe, Chris D.; Wiesner, Mark R.

2011-01-01

Background This commentary evolved from a workshop sponsored by the National Institute of Environmental Health Sciences titled "Superfund Contaminants: The Next Generation" held in Tucson, Arizona, in August 2009. All the authors were workshop participants.

Mechanical alloying and reactive milling in a high energy planetary mill

International Nuclear Information System (INIS)

Jiang Xianjin; Trunov, Mikhaylo A.; Schoenitz, Mirko; Dave, Rajesh N.; Dreizin, Edward L.

2009-01-01

Powder refinement in a planetary mill (Retsch PM 400-MA) is investigated experimentally and analyzed using discrete element modeling (DEM). Refinement is defined as the average size of the individual components in a composite powder. The specific milling dose, defined as the product of charge ratio and milling time, is used as an experimental parameter tracking the progress of the material refinement. This parameter is determined experimentally for milling of boron and titanium powders, for which the time of initiation of a self-sustained reaction is measured under different milling conditions. It is assumed that the reaction becomes self-sustaining when the same powder refinement is achieved. The DEM calculations established that the milling balls primarily roll along the milling container's perimeter. The inverse of the rate of energy dissipation resulting from this rolling motion is used as the DEM analog of the specific milling dose. The results correlate well with experimental observations.

Alternating current electrocoagulation for Superfund site remediation

International Nuclear Information System (INIS)

Farrell, C.W.

1991-01-01

A study is being conducted by Electro-Pure Systems, Inc. (EPS) under the Emerging Technology portion of the U.S. Environmental Protection Agency's (EPA's) Superfund Innovative Technology Evaluation (SITE) Program to study alternating current electrocoagulation for Superfund site remediation. Alternating current electrocoagulation has proven to be effective in agglomerating and removing colloidal solids, metals and certain organic contaminants from surrogate soils prepared from the US EPA's Synthetic Soil Matrix. Treatments under a wide range of operating conditions have enabled the optimum parameter settings to be established for multiple phase separation. Electrocoagulation enables appreciably enhanced filtration and dewatering rates to be realized for metals- and diesel fuel-spiked surrogate soil slurries; such enhancements are prompted by growth in the mean particle size of the clays and particulates from typically < 10 microns to as much as 150 microns depending on the degree of electrocoagulation. Reduction in the total suspended solids content of clays in all slurries in excess of 90% can routinely be achieved. Bench-scale experiments of the metals-spiked surrogate soils indicate that electrocoagulation preferentially concentrates soluble metals into the sludge phase; excellent metals separation (Pb, Cr, Cu, Cd) can be realized. Experiments on surrogate wastes spiked with volatile organics suggest that this technology is not capable of effecting good volatile extractions from the aqueous phase. Reductions in excess of 80% in the total organic carbon (TOC) content of the diesel fuel-spiked surrogates can, however, be achieved

Private-Sector Cleanup Expenditures and Transaction Costs at 18 Superfund Sites (1993)

Science.gov (United States)

Superfund allows the government either to clean up a site and recover its cost from the potentially responsible parties (PRPs) or to require the PRPs to undertake the cleanup themselves. This study examines private-sector expenditures and transaction-costs

Optimization Evaluation: Lee Chemical Superfund Site, City Of Liberty, Clay County, Missouri

Science.gov (United States)

The Lee Chemical Superfund Site (site) is located along Missouri Highway 210 in Liberty, Missouri, approximately 15 miles east of Kansas City, Missouri. Currently, the site is a vacant lot of approximately2.5 acres in a flat alluvial plain.

Groundwater restoration long beyond closure at the Homestake-Milan and United Nuclear-Church Rock uranium mill tailings piles, New Mexico, USA: full-scale programs requiring more than 20 years of active treatment

International Nuclear Information System (INIS)

Robinson, W.P.

1998-01-01

Since as early as 1975, groundwater contamination from New Mexico uranium mill tailings has been investigated with two sites -Homestake-Milan and United Nuclear-Church Rock -showing severe enough groundwater damage to merit listing on the US Environmental Protection Agency's (EPA) Superfund National Priority List -a nationwide list based on severity of pollution and water resource usefulness. These two sites provide valuable case studies for the first - 1950s -and second - 1970s -generations of uranium mill tailings facilities demonstrating the severity of contamination which ineffective control can allow and the challenge of full scale groundwater restoration. While the groundwater restoration at these sites began in the 1970s and 1980s, active treatment is anticipated into the 21st century. This paper summarizes the groundwater restoration programs at two of these sites - Homestake Mining Company's (HMC) Milan Mill (now called the ''Grants Project'') and United Nuclear Corporation's (UNC) Church Rock Mill. The two sites are summarized with respect to operations, groundwater impact, tailings disposal systems, hydrogeological characteristics of the site and affected areas, applicable standards, and remedial technology applied. This review provides a basis for initial comparisons with uranium mill tailings groundwater restoration challenges outside the USA. These sites provide an important benchmark the complexity of restoration at for large-scale uranium mill tailings sites. The longevity of the restoration efforts demonstrate the results of low-intensity responses to contamination upon detection and delayed enforcement actions. These ''witnesses'' to the value of effective pollution prevention in tailings design and full review and monitoring of tailings operations, have potential to be models of effective groundwater restoration. (orig.)

Uranium-mill appraisal program

International Nuclear Information System (INIS)

Everett, R.J.; Cain, C.L.

1982-08-01

The results of special team appraisals at NRC-licensed uranium mills in the period May to November 1981 are reported. Since the Three Mile Island accident, NRC management has instituted a program of special team appraisals of radiation protection programs at certain NRC-licensed facilities. These appraisals were designed to identify weaknesses and strengths in NRC-licensed programs, including those areas not covered by explicit regulatory requirements. The regulatory requirements related to occupational radiation protection and environmental monitoring at uranium mills have been extensively upgraded in the past few years. In addition, there was some NRC staff concern with respect to the effectiveness of NRC licensing and inspection programs. In response to this concern and to changes in mill requirements, the NRC staff recommended that team appraisals be conducted at mills to determine the adequacy of mill programs, the effectiveness of the new requirements, and mill management implementation of programs and requirements. This report describes the appraisal scope and methodology as well as summary findings and conclusions. Significant weaknesses identified during the mill appraisals are discussed as well as recommendations for improvements in uranium mill programs and mill licensing and inspection

Superfund record of decision (EPA Region 7): Cherokee County Superfund Site, Cherokee County, KS, July 29, 1996

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-08-01

The decision document presents the selected remedial action for the mining wastes at Operable Unit No. 07 of the Galena Subsite, which is part of the Cherokee County Superfund Site in Cherokee County, Kansas. The selected remedy includes actions for residential soils impacted by mining wastes and includes: Excavation and disposal of residential soils impacted by mining wastes; Health education for the general community and medical professionals; Institutional controls to guide future development in residential areas impacted by mining wastes; Treatability studies to evaluate the effectiveness of phosphate stabilization as a future alternative; and Operation and maintenance of all remedy aspects including, but not limited to, health education, institutional controls, and long-term monitoring.

Cleanups In My Community (CIMC) - Federal facilities that are also Superfund sites, National Layer

Data.gov (United States)

U.S. Environmental Protection Agency — Federal facilities are properties owned by the federal government. This data layer provides access to Federal facilities that are Superfund sites as part of the CIMC...

77 FR 13603 - Anniston PCB Superfund Site; Anniston, Calhoun County, AL; Correction

Science.gov (United States)

2012-03-07

... ENVIRONMENTAL PROTECTION AGENCY [FRL-9644-2; CERCLA-04-2012-3763] Anniston PCB Superfund Site... FR 11533 (FRL-9637-7), EPA posted a Notice of Amended Settlement concerning the Anniston PCB... the settlement are available from Ms. Paula V. Painter. Submit your comments by Site name Anniston PCB...

Remediation System Evaluation, Tutu Wellfield Superfund Site, St. Thomas, U.S. Virgin Islands

Science.gov (United States)

The Tutu Wellfield Superfund Site is a 1.5 square mile site located on the eastern end of St. Thomas, U.S. Virgin Islands (USVI) within the upper Turpentine Run surface drainage basin in the Anna’s Retreat area.

16 CFR 300.29 - Garments or products composed of or containing miscellaneous cloth scraps.

Science.gov (United States)

2010-01-01

... 16 Commercial Practices 1 2010-01-01 2010-01-01 false Garments or products composed of or containing miscellaneous cloth scraps. 300.29 Section 300.29 Commercial Practices FEDERAL TRADE COMMISSION... chiefly woolen fibers with the balance of undetermined mixtures of cotton, rayon or other non-woolen...

Blasting at a Superfund chemical waste site

International Nuclear Information System (INIS)

Burns, D.R.

1991-01-01

During the summer of 1989, Maine Drilling and Blasting of Gardiner, Maine was contracted by Cayer Corporation of Harvard, Massachusetts to drill and blast an interceptor trench at the Nyanza Chemical Superfund Site in Ashland, Massachusetts. The interceptor trench was to be 1,365 feet long and to be blasted out of granite. The trench was to be 12 feet wide at the bottom with 1/1 slopes, the deepest cut being 30 feet deep. A French drain 12 feet wide by 15 to 35 feet deep was blasted below the main trench on a 2% slope from its center to each end. A French drain is an excavation where the rock is blasted but not dug. The trench would be used as a perimeter road with any ground water flow going through the French drain flowing to both ends of the trench. Being a Superfund project turned a simple blasting project into a regulatory nightmare. The US Environmental Protection Agency performed all the chemical related functions on site. The US Army Corps of Engineers was overseeing all related excavation and construction on site, as was the Massachusetts Department of Environmental Quality Engineering, the local Hazardous Wastes Council, and the local Fire Department. All parties had some input with the blasting and all issues had to be addressed. The paper outlines the project, how it was designed and completed. Also included is an outline of the blast plan to be submitted for approval, an outline of the Safety/Hazardous Waste training and a description of all the problems which arose during the project by various regulatory agencies

Integration of micro milling highspeed spindle on a microEDM-milling machine set-up

DEFF Research Database (Denmark)

De Grave, Arnaud; Hansen, Hans Nørgaard; Andolfatto, Loic

2009-01-01

In order to cope with repositioning errors and to combine the fast removal rate of micro milling with the precision and small feature size achievable with micro EDM milling, a hybrid micro-milling and micro-EDM milling centre was built and tested. The aim was to build an affordable set-up, easy...... by micro milling. Examples of test parts are shown and used as an experimental validation....

Uranium Mill Tailings Management

International Nuclear Information System (INIS)

Nelson, J.D.

1982-01-01

This book presents the papers given at the Fifth Symposium on Uranium Mill Tailings Management. Advances made with regard to uranium mill tailings management, environmental effects, regulations, and reclamation are reviewed. Topics considered include tailings management and design (e.g., the Uranium Mill Tailings Remedial Action Project, environmental standards for uranium mill tailings disposal), surface stabilization (e.g., the long-term stability of tailings, long-term rock durability), radiological aspects (e.g. the radioactive composition of airborne particulates), contaminant migration (e.g., chemical transport beneath a uranium mill tailings pile, the interaction of acidic leachate with soils), radon control and covers (e.g., radon emanation characteristics, designing surface covers for inactive uranium mill tailings), and seepage and liners (e.g., hydrologic observations, liner requirements)

Guidance: Strategies to Achieve Timely Settlement and Implementation of RD/RA at Superfund Sites

Science.gov (United States)

Memorandum recommends strategies to encourage PRPs to enter into a settlement using the model RD/RA Consent Decree; discusses the current model UAO; and suggests practical alternatives to expedite Superfund settlements and the cleanup process.

Renton's Quendall Terminals on List of EPA Superfund Sites Targeted for Immediate, Intense Attention

Science.gov (United States)

EPA released the list of Superfund sites that Administrator Pruitt has targeted for intense and immediate attention, including the Quendall Terminals Site, a former creosote facility on the shore of Lake Washington in Renton, Washington.

Cleanups In My Community (CIMC) - Base Realignment and Closure (BRAC) Superfund Sites, National Layer

Data.gov (United States)

U.S. Environmental Protection Agency — This data layer provides access to Base Realignment and Closure (BRAC) Superfund Sites as part of the CIMC web service. EPA works with DoD to facilitate the reuse...

Preliminary Test of Upgraded Conventional Milling Machine into PC Based CNC Milling Machine

International Nuclear Information System (INIS)

Abdul Hafid

2008-01-01

CNC (Computerized Numerical Control) milling machine yields a challenge to make an innovation in the field of machining. With an action job is machining quality equivalent to CNC milling machine, the conventional milling machine ability was improved to be based on PC CNC milling machine. Mechanically and instrumentally change. As a control replacing was conducted by servo drive and proximity were used. Computer programme was constructed to give instruction into milling machine. The program structure of consists GUI model and ladder diagram. Program was put on programming systems called RTX software. The result of up-grade is computer programming and CNC instruction job. The result was beginning step and it will be continued in next time. With upgrading ability milling machine becomes user can be done safe and optimal from accident risk. By improving performance of milling machine, the user will be more working optimal and safely against accident risk. (author)

Evaluating public participation in environmental decision-making: EPA's superfund community involvement program.

Science.gov (United States)

Susan Charnley; Bruce. Engelbert

2005-01-01

This article discusses an 8-year, ongoing project that evaluates the Environmental Protection Agency's Superfund community involvement program. The project originated as a response to the Government Performance and Results Act, which requires federal agencies to articulate program goals, and evaluate and report their progress in meeting those goals. The evaluation...

Effects of Dry-Milling and Wet-Milling on Chemical, Physical and Gelatinization Properties of Rice Flour

Directory of Open Access Journals (Sweden)

Jitranut Leewatchararongjaroen

2016-09-01

Full Text Available Rice flour from nine varieties, subjected to dry- and wet-milling processes, was determined for its physical and chemical properties. The results revealed that milling method had an effect on properties of flour. Wet-milling process resulted in flour with significantly lower protein and ash contents and higher carbohydrate content. Wet-milled flour also tended to have lower lipid content and higher amylose content. In addition, wet-milled rice flour contained granules with smaller average size compared to dry-milled samples. Swelling power at 90 °C of wet-milled samples was higher while solubility was significantly lower than those of dry-milled flour. Dry milling process caused the destruction of the crystalline structure and yielded flour with lower crystallinity compared to wet-milling process, which resulted in significantly lower gelatinization enthalpy.

Investigation of the milling capabilities of the F10 Fine Grind mill using Box-Behnken designs.

Science.gov (United States)

Tan, Bernice Mei Jin; Tay, Justin Yong Soon; Wong, Poh Mun; Chan, Lai Wah; Heng, Paul Wan Sia

2015-01-01

Size reduction or milling of the active is often the first processing step in the design of a dosage form. The ability of a mill to convert coarse crystals into the target size and size distribution efficiently is highly desirable as the quality of the final pharmaceutical product after processing is often still dependent on the dimensional attributes of its component constituents. The F10 Fine Grind mill is a mechanical impact mill designed to produce unimodal mid-size particles by utilizing a single-pass two-stage size reduction process for fine grinding of raw materials needed in secondary processing. Box-Behnken designs were used to investigate the effects of various mill variables (impeller, blower and feeder speeds and screen aperture size) on the milling of coarse crystals. Response variables included the particle size parameters (D10, D50 and D90), span and milling rate. Milled particles in the size range of 5-200 μm, with D50 ranging from 15 to 60 μm, were produced. The impeller and feeder speeds were the most critical factors influencing the particle size and milling rate, respectively. Size distributions of milled particles were better described by their goodness-of-fit to a log-normal distribution (i.e. unimodality) rather than span. Milled particles with symmetrical unimodal distributions were obtained when the screen aperture size was close to the median diameter of coarse particles employed. The capacity for high throughput milling of particles to a mid-size range, which is intermediate between conventional mechanical impact mills and air jet mills, was demonstrated in the F10 mill. Prediction models from the Box-Behnken designs will aid in providing a better guide to the milling process and milled product characteristics. Copyright © 2014 Elsevier B.V. All rights reserved.

75 FR 38100 - National Institute of Environmental Health Sciences Superfund Hazardous Substance Research and...

Science.gov (United States)

2010-07-01

...- traditional communication methods to make the significance and applicability of SRP-funded research... and Social Sciences Research, and National Institute of Biomedical Imaging and Bioengineering. [cir... Superfund Hazardous Substance Research and Training Program Strategic Plan; Request for Comments ACTION...

Biomonitoring for metal contamination near two Superfund sites in Woburn, Massachusetts, using phytochelatins

International Nuclear Information System (INIS)

Gawel, James E.; Hemond, Harold F.

2004-01-01

Characterizing the spatial extent of groundwater metal contamination traditionally requires installing sampling wells, an expensive and time-consuming process in urban areas. Moreover, extrapolating biotic effects from metal concentrations alone is problematic, making ecological risk assessment difficult. Our study is the first to examine the use of phytochelatin measurements in tree leaves for delimiting biological metal stress in shallow, metal-contaminated groundwater systems. Three tree species (Rhamnus frangula, Acer platanoides, and Betula populifolia) growing above the shallow groundwater aquifer of the Aberjona River watershed in Woburn, Massachusetts, display a pattern of phytochelatin production consistent with known sources of metal contamination and groundwater flow direction near the Industri-Plex Superfund site. Results also suggest the existence of a second area of contaminated groundwater and elevated metal stress near the Wells G and H Superfund site downstream, in agreement with a recent EPA ecological risk assessment. Possible contamination pathways at this site are discussed

Einstein-Yang-Mills from pure Yang-Mills amplitudes

Energy Technology Data Exchange (ETDEWEB)

Nandan, Dhritiman; Plefka, Jan [Institut für Physik and IRIS Adlershof, Humboldt-Universität zu Berlin,Zum Großen Windkanal 6, D-12489 Berlin (Germany); Schlotterer, Oliver [Max-Planck-Institut für Gravitationsphysik, Albert-Einstein-Institut,Am Mühlenberg 1, D-14476 Potsdam (Germany); Wen, Congkao [I.N.F.N. Sezione di Roma Tor Vergata,Via della Ricerca Scientifica, 00133 Roma (Italy)

2016-10-14

We present new relations for scattering amplitudes of color ordered gluons and gravitons in Einstein-Yang-Mills theory. Tree-level amplitudes of arbitrary multiplicities and polarizations involving up to three gravitons and up to two color traces are reduced to partial amplitudes of pure Yang-Mills theory. In fact, the double-trace identities apply to Einstein-Yang-Mills extended by a dilaton and a B-field. Our results generalize recent work of Stieberger and Taylor for the single graviton case with a single color trace. As the derivation is made in the dimension-agnostic Cachazo-He-Yuan formalism, our results are valid for external bosons in any number of spacetime dimensions. Moreover, they generalize to the superamplitudes in theories with 16 supercharges.

EMERGING TECHNOLOGY BULLETIN: RECLAMATION OF LEAD FROM SUPERFUND WASTE MATERIAL USING SECONDARY LEAD SMELTERS

Science.gov (United States)

This process involves incorporating lead-contaminated Superfund waste with the regular feed to a secondary lead smelter. Since secondary lead smelters already recover lead from recycled automobile batteries, it seems likely that this technology could be used to treat waste from ...

7 CFR 868.310 - Grades and grade requirements for the classes Long Grain Milled Rice, Medium Grain Milled Rice...

Science.gov (United States)

2010-01-01

... Grain Milled Rice, Medium Grain Milled Rice, Short Grain Milled Rice, and Mixed Milled Rice. (See also Â... Milled Rice Principles Governing Application of Standards § 868.310 Grades and grade requirements for the classes Long Grain Milled Rice, Medium Grain Milled Rice, Short Grain Milled Rice, and Mixed Milled Rice...

75 FR 71463 - Woodland Mills Corporation Mill Spring, NC; Notice of Revised Determination on Reconsideration

Science.gov (United States)

2010-11-23

... DEPARTMENT OF LABOR Employment and Training Administration [TA-W-73,695] Woodland Mills Corporation Mill Spring, NC; Notice of Revised Determination on Reconsideration By application dated July 22... regarding the eligibility of workers and former workers of Woodland Mills Corporation, Mill Spring, North...

Evaluation of End Mill Coatings

Energy Technology Data Exchange (ETDEWEB)

L. J. Lazarus; R. L. Hester,

2005-08-01

Milling tests were run on families of High Speed Steel (HSS) end mills to determine their lives while machining 304 Stainless Steel. The end mills tested were made from M7, M42 and T15-CPM High Speed Steels. The end mills were also evaluated with no coatings as well as with Titanium Nitride (TiN) and Titanium Carbo-Nitride (TiCN) coatings to determine which combination of HSS and coating provided the highest increase in end mill life while increasing the cost of the tool the least. We found end mill made from M42 gave us the largest increase in tool life with the least increase in cost. The results of this study will be used by Cutting Tool Engineering in determining which end mill descriptions will be dropped from our tool catalog.

Bioassay for uranium mill tailings

International Nuclear Information System (INIS)

Tschaeche, A.N.

1986-01-01

Uranium mill tailings are composed of fine sand that contains, among other things, some uranium (U/sup 238/ primarily), and all of the uranium daughters starting with /sup 230/Th that are left behind after the usable uranium is removed in the milling process. Millions of pounds of tailings are and continue to be generated at uranium mills around the United States. Discrete uranium mill tailings piles exist near the mills. In addition, the tailings materials were used in communities situated near mill sites for such purposes as building materials, foundations for buildings, pipe runs, sand boxes, gardens, etc. The Uranium Mill Tailings Remedial Action Project (UMTRAP) is a U.S. Department of Energy Program designed with the intention of removing or stabilizing the mill tailings piles and the tailings used to communities so that individuals are not exposed above the EPA limits established for such tailings materials. This paper discusses the bioassay programs that are established for workers who remove tailings from the communities in which they are placed

Biomass torrefaction mill

Science.gov (United States)

Sprouse, Kenneth M.

2016-05-17

A biomass torrefaction system includes a mill which receives a raw biomass feedstock and operates at temperatures above 400 F (204 C) to generate a dusty flue gas which contains a milled biomass product.

1992 update of US EPA's Superfund Innovative Technology Evaluation (SITE) Emerging Technology Program

International Nuclear Information System (INIS)

Lewis, N.M.; Barkley, N.P.; Williams, T.

1992-01-01

The Superfund Innovative Technology Evaluation (SITE) Emerging Technology Program (ETP) has financially supported further development of bench- and pilot-scale testing and evaluation of innovative technologies for use at hazardous waste sites for five years. The ETP was established under the Superfund Amendments and Reauthorization Act (SARA) of 1986. The ETP complies with the goal of the SITE Program to promote, accelerate and make commercially available the development of alternative/innovative treatment technologies for use at Superfund sites. Technologies are submitted to the ETP through yearly solicitations for Preproposals. Applicants are asked to submit a detailed project proposal and a cooperative agreement application that requires Developer/EPA cost sharing. EPA co-funds selected Developers for one to two years. Second-year funding requires documentation of significant progress during the first year. Facilities, equipment, data collection, performance and development are monitored throughout the project. The US Department of Energy (DOE) and the US Air Force (USAF) are participants in the ETP. DOE has co-funded ETP projects since 1990 and the USAF since 1991. A goal of the ETP is to move developed technologies to the field-demonstration stage. A developer may be considered for participation in the SITE Demonstration Program if performance in the ETP indicates the technology is field-ready for evaluation. Six technology categories: biological, chemical, materials handling, physical, solidification/stabilization and thermal, are presently in the ETP. Technologies of primary interest to EPA are those that can treat complex mixtures of hazardous organic and inorganic contaminants and provide improved solids handling and/or pretreatment. An account of the background and progress of the ETP's first five years is presented in this paper. Technologies currently in the ETP are noted, and developers and EPA Project Managers, are listed. 4 refs., 11 figs., 6 tabs

Decontamination effect of milling by a jet mill on bacteria in rice flour.

Science.gov (United States)

Sotome, Itaru; Nei, Daisuke; Tsuda, Masuko; Mohammed, Sharif Hossen; Takenaka, Makiko; Okadome, Hiroshi; Isobe, Seiichiro

2011-06-01

The decontamination effect of milling by a jet mill was investigated by counting the number of bacteria in brown and white rice flour with mean particle diameters of 3, 20, and 40µm prepared by the jet mill. In the jet mill, the particles are crushed and reduced in size by the mechanical impact caused by their collision. Although the brown and white rice grains were contaminated with approximately 10(6) and 10(5) CFU/g bacteria, the microbial load of the rice flour decreased as the mean particle diameter decreased, ultimately decreasing to approximately 104 and 103 CFU/g in the brown and white rice flour. The temperature and pressure changes of the sample were not considered to have an effect on reducing the bacterial count during the milling. Hence, it was thought that the rice flour was decontaminated by other effects.

A General Chemistry Assignment Analyzing Environmental Contamination for the Depue, IL, National Superfund Site

Science.gov (United States)

Saslow Gomez, Sarah A.; Faurie-Wisniewski, Danielle; Parsa, Arlen; Spitz, Jeff; Spitz, Jennifer Amdur; Loeb, Nancy C.; Geiger, Franz M.

2015-01-01

The classroom exercise outlined here is a self-directed assignment that connects students to the environmental contamination problem surrounding the DePue Superfund site. By connecting chemistry knowledge gained in the classroom with a real-world problem, students are encouraged to personally connect with the problem while simultaneously…

Hybrid ABC Optimized MARS-Based Modeling of the Milling Tool Wear from Milling Run Experimental Data

OpenAIRE

Garc?a Nieto, Paulino Jos?; Garc?a-Gonzalo, Esperanza; Ord??ez Gal?n, Celestino; Bernardo S?nchez, Antonio

2016-01-01

Milling cutters are important cutting tools used in milling machines to perform milling operations, which are prone to wear and subsequent failure. In this paper, a practical new hybrid model to predict the milling tool wear in a regular cut, as well as entry cut and exit cut, of a milling tool is proposed. The model was based on the optimization tool termed artificial bee colony (ABC) in combination with multivariate adaptive regression splines (MARS) technique. This optimization mechanism i...

Beneficial uses of paper mill residuals for New York State`s recycled-paper mills. Final report

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-09-01

This report evaluates the New York paper mill industry in terms of the productive management and treatment of solid wastes. It identifies current efforts by recycling mills to beneficially use paper mill residuals (often called sludge) and suggests additional options that should be considered by the industry in general and individual mills in particular. It also examines the regulations and economics affecting the mills and suggests actions that could improve the industry`s ability to convert wastes to value-added products. The report recommends that the mills should continue measures to reduce fiber and filler clay losses, promote the transfer of usable fiber and clay to mills able to use them, upgrade sludge dewatering capabilities, and take a more regional approach to solid waste disposal problems. State agencies are urged to support these efforts, encourage the development and commercialization of new beneficial use technologies, and reduce regulatory barriers whenever possible.

75 FR 81269 - Ward Transformer Superfund Site Raleigh, Wake County, NC; Notice of Settlements

Science.gov (United States)

2010-12-27

... ENVIRONMENTAL PROTECTION AGENCY [Docket EPA-RO4-SFUND-2010-1053, FRL-9243-2] Ward Transformer... entered into a five settlements for reimbursement of past response costs concerning the Ward Transformer... Docket ID No. EPA-RO4- SFUND-2010-1053 or Site name Ward Transformer Superfund Site by one of the...

Case studies of community relations on DOE's Formerly Utilized Sites Remedial Action Program as models for Superfund sites

International Nuclear Information System (INIS)

Plant, S.W.; Adler, D.G.

1995-01-01

Ever since the US Department of Energy (DOE) created its Formerly Utilized Sites Remedial Action Program (FUSRAP) in 1974, there has been a community relations program. The community relations effort has grown as FUSRAP has grown. With 20 of 46 sites now cleaned up, considerable experience in working with FUSRAP stakeholders has been gained. Why not share that experience with others who labor on the Superfund sites? Many similarities exist between the Superfund sites and FUSRAP. FUSRAP is a large, multiple-site environmental restoration program. The challenges range from small sites requiring remedial actions measurable in weeks to major sites requiring the full remedial investigation/feasibility study process. The numerous Superfund sites throughout the United States offer the same diversity, both geographically and technically. But before DOE offers FUSRAP's community relations experience as a model, it needs to make clear that this will be a realistic model. As experiences are shared, DOE will certainly speak of the efforts that achieved its goals. But many of the problems that DOE encountered along the way will also be related. FUSRAP relies on a variety of one- and two-way communication techniques for involving stakeholders in the DOE decision-making process. Some of the techniques and experiences from the case studies are presented

78 FR 76143 - Proposed CERCLA Settlement Relating to the Paul's Tank Cleaning Service Superfund Site...

Science.gov (United States)

2013-12-16

... Paul's Tank Cleaning Service Superfund Site, Burlington County, New Jersey AGENCY: Environmental.... (``Settling Party''). The Settling Party is a potentially responsible party, pursuant to Section 107(a) of CERCLA, and thus is potentially liable for response costs incurred at or in connection Paul's Tank...

Airborne effluent control at uranium mills

International Nuclear Information System (INIS)

Sears, M.B.

1976-01-01

The Oak Ridge National Laboratory has made an engineering cost--environmental benefit study of radioactive waste treatment systems for decreasing the amount of radioactive materials released from uranium ore processing mills. This paper summarizes the results of the study which pertain to the control and/or abatement of airborne radioactive materials from the mill processes. The tailings area is not included. Present practices in the uranium milling industry, with particular emphasis on effluent control and waste management, have been surveyed. A questionnaire was distributed to each active mill in the United States. Replies were received from about 75 percent of the mill operators. Visits were made to six operating uranium mills that were selected because they represented the different processes in use today and the newest, most modern in mill designs. Discussions were held with members of the Region IV Office of NRC and the Grand Junction Office of ERDA. Nuclear Science Abstracts, as well as other sources, were searched for literature pertinent to uranium mill processes, effluent control, and waste management

FM Interviews: Stephanie Mills

OpenAIRE

Valauskas, Edward

2002-01-01

Stephanie Mills is an author, editor, lecturer and ecological activist who has concerned herself with the fate of the earth and humanity since 1969, when her commencement address at Mills College in Oakland, Calif., drew the attention of a nation. Her speech, which the New York Times called "perhaps the most anguished statement" of the year's crop of valedictory speeches, predicted a bleak future. According to Mills, humanity was destined for suicide, the result of overpopulation and overuse ...

77 FR 21433 - Regulated Navigation Area; Pacific Sound Resources and Lockheed Shipyard EPA Superfund Cleanup...

Science.gov (United States)

2012-04-10

... superfund cleanup remediation efforts. This RNA will prohibit activities that would disturb the seabed, such... or capped are arsenic, copper, lead, mercury, zinc, PAHs and PCBs. The metal contaminants were... installed in the designated regulated navigation area, pursuant to the remediation efforts of the U.S...

Rough mill simulator version 3.0: an analysis tool for refining rough mill operations

Science.gov (United States)

Edward Thomas; Joel Weiss

2006-01-01

ROMI-3 is a rough mill computer simulation package designed to be used by both rip-first and chop-first rough mill operators and researchers. ROMI-3 allows users to model and examine the complex relationships among cutting bill, lumber grade mix, processing options, and their impact on rough mill yield and efficiency. Integrated into the ROMI-3 software is a new least-...

Hybrid ABC Optimized MARS-Based Modeling of the Milling Tool Wear from Milling Run Experimental Data.

Science.gov (United States)

García Nieto, Paulino José; García-Gonzalo, Esperanza; Ordóñez Galán, Celestino; Bernardo Sánchez, Antonio

2016-01-28

Milling cutters are important cutting tools used in milling machines to perform milling operations, which are prone to wear and subsequent failure. In this paper, a practical new hybrid model to predict the milling tool wear in a regular cut, as well as entry cut and exit cut, of a milling tool is proposed. The model was based on the optimization tool termed artificial bee colony (ABC) in combination with multivariate adaptive regression splines (MARS) technique. This optimization mechanism involved the parameter setting in the MARS training procedure, which significantly influences the regression accuracy. Therefore, an ABC-MARS-based model was successfully used here to predict the milling tool flank wear (output variable) as a function of the following input variables: the time duration of experiment, depth of cut, feed, type of material, etc . Regression with optimal hyperparameters was performed and a determination coefficient of 0.94 was obtained. The ABC-MARS-based model's goodness of fit to experimental data confirmed the good performance of this model. This new model also allowed us to ascertain the most influential parameters on the milling tool flank wear with a view to proposing milling machine's improvements. Finally, conclusions of this study are exposed.

Hybrid ABC Optimized MARS-Based Modeling of the Milling Tool Wear from Milling Run Experimental Data

Directory of Open Access Journals (Sweden)

Paulino José García Nieto

2016-01-01

Full Text Available Milling cutters are important cutting tools used in milling machines to perform milling operations, which are prone to wear and subsequent failure. In this paper, a practical new hybrid model to predict the milling tool wear in a regular cut, as well as entry cut and exit cut, of a milling tool is proposed. The model was based on the optimization tool termed artificial bee colony (ABC in combination with multivariate adaptive regression splines (MARS technique. This optimization mechanism involved the parameter setting in the MARS training procedure, which significantly influences the regression accuracy. Therefore, an ABC–MARS-based model was successfully used here to predict the milling tool flank wear (output variable as a function of the following input variables: the time duration of experiment, depth of cut, feed, type of material, etc. Regression with optimal hyperparameters was performed and a determination coefficient of 0.94 was obtained. The ABC–MARS-based model's goodness of fit to experimental data confirmed the good performance of this model. This new model also allowed us to ascertain the most influential parameters on the milling tool flank wear with a view to proposing milling machine's improvements. Finally, conclusions of this study are exposed.

Hybrid ABC Optimized MARS-Based Modeling of the Milling Tool Wear from Milling Run Experimental Data

Science.gov (United States)

García Nieto, Paulino José; García-Gonzalo, Esperanza; Ordóñez Galán, Celestino; Bernardo Sánchez, Antonio

2016-01-01

Milling cutters are important cutting tools used in milling machines to perform milling operations, which are prone to wear and subsequent failure. In this paper, a practical new hybrid model to predict the milling tool wear in a regular cut, as well as entry cut and exit cut, of a milling tool is proposed. The model was based on the optimization tool termed artificial bee colony (ABC) in combination with multivariate adaptive regression splines (MARS) technique. This optimization mechanism involved the parameter setting in the MARS training procedure, which significantly influences the regression accuracy. Therefore, an ABC–MARS-based model was successfully used here to predict the milling tool flank wear (output variable) as a function of the following input variables: the time duration of experiment, depth of cut, feed, type of material, etc. Regression with optimal hyperparameters was performed and a determination coefficient of 0.94 was obtained. The ABC–MARS-based model's goodness of fit to experimental data confirmed the good performance of this model. This new model also allowed us to ascertain the most influential parameters on the milling tool flank wear with a view to proposing milling machine's improvements. Finally, conclusions of this study are exposed. PMID:28787882

Effect of milling time on microstructure and properties of Nano-titanium polymer by high-energy ball milling

Science.gov (United States)

Wang, Bo; Wei, Shicheng; Wang, Yujiang; Liang, Yi; Guo, Lei; Xue, Junfeng; Pan, Fusheng; Tang, Aitao; Chen, Xianhua; Xu, Binshi

2018-03-01

Nano-titanium (Nano-Ti) was prepared by high-energy ball milling from pure Ti power and grinding agents (Epoxy resin) at room temperature. The effect of milling time on structure and properties of Nano-Ti polymer were investigated systematically. The results show that high-energy ball milling is an effective way to produce Nano-Ti polymer. The dispersion stability and compatibility between Ti power and grinding agents are improved by prolonging the milling time at a certain degree, that is to say, the optimization milling time is 240 min. The particle size of Ti powder and the diffraction peaks intensity of Ti decrease obviously as the milling time increases due to the compression stress, shear friction and other mechanical forces are formed during ball milling. FT-IR result displays that the wavenumber of all the bands move to lower wavenumber after ball milling, and the epoxy ring is open. The system internal energy rises owing to the broken epoxy group and much more Nano-Ti is formed to promote the grafting reaction between Nano-Ti and epoxy resin. The results from TEM and XPS also prove that. And the grafting ration is maximum as the milling time is 240 min, the mass loss ratio is 17.53%.

Assessment of technologies for the remediation of radioactively contaminated Superfund sites

International Nuclear Information System (INIS)

1990-01-01

The report is a screening evaluation of information needs for the development of generic treatability studies for the remediation of Superfund Radiation Sites on the National Priorities List (NPL). It presents a categorization of the 25 radiation sites currently proposed or listed on the NPL, and provides a rating system for evaluating technologies that may be used to remediate these sites. It also identifies gaps in site assessment and technology data and provides information about and recommendations for technology development

Issuance of Final Guidance: Ecological Risk Assessment and Risk Management Principles for Superfund Sites, October 7, 1999

Science.gov (United States)

This guidance is intended to help Superfund risk managers make ecological risk management decisions that are based on sound science, consistent across Regions, and present a characterization of site risks that is transparent to the public.

EPA RREL's mobile volume reduction unit advances soil washing at four Superfund sites

International Nuclear Information System (INIS)

Gaire, R.; Borst, M.

1994-01-01

Research testing of the US. Environmental Protection Agency (EPA) Risk Reduction Engineering Laboratory's (RREL) Volume Reduction Unit (VRU), produced data helping advance soil washing as a remedial technology for contaminated soils. Based on research at four Superfund sites, each with a different matrix of organic contaminants, EPA evaluated the soil technology and provided information to forecast realistic, full-scale remediation costs. Primarily a research tool, the VRU is RREL's mobile test unit for investigating the breadth of this technology. During a Superfund Innovative Technology Evaluation (SITE) Demonstration at Escambia Wood Treating Company Site, Pensacola, FL, the VRU treated soil contaminated with pentachlorophenol (PCP) and polynuclear aromatic hydrocarbon-laden creosote (PAH). At Montana Pole and Treatment Plant Site, Butte, MT, the VRU treated soil containing PCP mixed with diesel oil (measured as total petroleum hydrocarbons) and a trace of dioxin. At Dover Air Force Base Site, Dover, DE, the VRU treated soil containing JP-4 jet fuel, measured as TPHC. At Sand Creek Site, Commerce City, CO, the feed soil at this site was contaminated with two pesticides: heptachlor and dieldrin. Less than 10 percent of these pesticides remained in the treated coarse soil fractions

75 FR 53694 - Florida Petroleum Reprocessors Superfund Site; Davie, Broward County, FL; Notice of Settlement

Science.gov (United States)

2010-09-01

... ENVIRONMENTAL PROTECTION AGENCY [Docket EPA-RO4-SFUND-2010-0729, FRL-9196-1] Florida Petroleum... entered into a settlement for reimbursement of past response costs concerning the Florida Petroleum... No. EPA-RO4- SFUND-2010-0729 or Site name Florida Petroleum Reprocessors Superfund Site by one of the...

Focused ion beam milling of carbon fibres

International Nuclear Information System (INIS)

Huson, Mickey G.; Church, Jeffrey S.; Hillbrick, Linda K.; Woodhead, Andrea L.; Sridhar, Manoj; Van De Meene, Allison M.L.

2015-01-01

A focused ion beam has been used to mill both individual carbon fibres as well as fibres in an epoxy composite, with a view to preparing flat surfaces for nano-indentation. The milled surfaces have been assessed for damage using scanning probe microscopy nano-indentation and Raman micro-probe analysis, revealing that FIB milling damages the carbon fibre surface and covers surrounding areas with debris of disordered carbon. The debris is detected as far as 100 μm from the milling site. The energy of milling as well as the orientation of the beam was varied and shown to have an effect when assessed by Raman spectroscopy. - Highlights: • Focused ion beam (FIB) milling was used to mill flat surfaces on carbon fibres. • Raman spectroscopy showed amorphous carbon was generated during FIB milling. • The amorphous debris is detected as far as 100 μm from the milling site. • This surface degradation was confirmed by nano-indentation experiments.

Superfund at work: Hazardous waste cleanup efforts nationwide, fall 1992. (CIBA-GEIGY Corporation, McIntosh, Alabama)

International Nuclear Information System (INIS)

1992-01-01

On March 31, 1992, the U.S. Environmental Protection Agency (EPA) reached an agreement with Ciba-Geigy Corporation in McIntosh, Alabama to clean up soil and ground water contaminated by DDT, herbicides, and chemicals. The agreement is one of the largest private party settlements in Superfund history, valued at approximately $120 million. EPA activities at the site included: conducting preliminary contamination investigations jointly with the Alabama Environmental Health Administration, beginning in 1979; designing a multi-phased cleanup that is responsive to the complex nature of the contamination and reduces potential risk to the local population and environment; and awarding a grant to a community group to help them participate in cleanup decisions. Ciba-Geigy, like EPA, has made consistent efforts to build and maintain good relations with the community. These efforts demonstrate the increasing trend toward cooperation between industries, local communities, and EPA at Superfund sites

HISTORY AND ACCOMPLISHMENTS OF THE US EPA'S SUPERFUND INNOVATIVE TECHNOLOGY EVALUATION (SITE) MONITORING AND MEASUREMENT (MMT) PROGRAM

Science.gov (United States)

This manuscript presents the history and evolution of the U.S. Environmental Protection Agency's (EPA) Superfund Innovative Technology Evaluation (SITE) Monitoring and Measurement Technology (MMT) Program. This includes a discussion of how the fundamental concepts of a performanc...

Surface Quality of Staggered PCD End Mill in Milling of Carbon Fiber Reinforced Plastics

Directory of Open Access Journals (Sweden)

Guangjun Liu

2017-02-01

Full Text Available Machined surface quality determines the reliability, wear resistance and service life of carbon fiber reinforced plastic (CFRP workpieces. In this work, the formation mechanism of the surface topography and the machining defects of CFRPs are proposed, and the influence of milling parameters and fiber cutting angles on the surface quality of CFRPs is obtained, which can provide a reference for extended tool life and good surface quality. Trimming and slot milling tests of unidirectional CFRP laminates are performed. The surface roughness of the machined surface is measured, and the influence of milling parameters on the surface roughness is analyzed. A regression model for the surface roughness of CFRP milling is established. A significance test of the regression model is conducted. The machined surface topography of milling CFRP unidirectional laminates with different fiber orientations is analyzed, and the effect of fiber cutting angle on the surface topography of the machined surface is presented by using a digital super depth-of-field microscope and scanning electron microscope (SEM. To study the influence of fiber cutting angle on machining defects, the machined topography under different fiber orientations is analyzed. The slot milling defects and their formation mechanism under different fiber cutting angles are investigated.

77 FR 58989 - Proposed CERCLA Administrative Cost Recovery Settlement for the Buckbee-Mears Co. Superfund Site...

Science.gov (United States)

2012-09-25

... paid $150,000 attributable to the costs of marketing and selling the Properties; (b) The Bank will pay... ENVIRONMENTAL PROTECTION AGENCY [FRL-9720-7] Proposed CERCLA Administrative Cost Recovery... costs concerning the Buckbee-Mears Co. Superfund Site located in Cortland, Cortland County, New York...

Remediation of the Wells G & H Superfund Site, Woburn, Massachusetts.

Science.gov (United States)

Bair, E Scott; Metheny, Maura A

2002-01-01

Remediation of ground water and soil contamination at the Wells G & H Superfund Site, Woburn, Massachusetts, uses technologies that reflect differences in hydrogeologic settings, concentrations of volatile organic compounds (VOCs), and costs of treatment. The poorly permeable glacial materials that overlie fractured bedrock at the W.R. Grace property necessitate use of closely spaced recovery wells. Contaminated ground water is treated with hydrogen peroxide and ultraviolet (UV) oxidation. At UniFirst, a deep well completed in fractured bedrock removes contaminated ground water, which is treated by hydrogen peroxide, UV oxidation, and granular activated carbon (GAC). The remediation system at Wildwood integrates air sparging, soil-vapor extraction, and ground water pumping. Air stripping and GAC are used to treat contaminated water; GAC is used to treat contaminated air. New England Plastics (NEP) uses air sparging and soil-vapor extraction to remove VOCs from the unsaturated zone and shallow ground water. Contaminated air and water are treated using separate GAC systems. After nine years of operation at W.R. Grace and UniFirst, 30 and 786 kg, respectively, of VOCs have been removed. In three years of operation, 866 kg of VOCs have been removed at Wildwood. In 15 months of operation, 36 kg of VOCs were removed at NEP. Characterization work continues at the Olympia Nominee Trust, Whitney Barrel, Murphy Waste Oil, and Aberjona Auto Parts properties. Risk assessments are being finalized that address heavy metals in the floodplain sediments along the Aberjona River that are mobilized from the Industri-Plex Superfund Site located a few miles upstream.

Yang-Mills gravity in biconformal space

International Nuclear Information System (INIS)

Anderson, Lara B; Wheeler, James T

2007-01-01

We write a gravity theory with Yang-Mills-type action using the biconformal gauging of the conformal group. We show that the resulting biconformal Yang-Mills gravity theories describe 4-dim, scale-invariant general relativity in the case of slowly changing fields. In addition, we systematically extend arbitrary 4-dim Yang-Mills theories to biconformal space, providing a new arena for studying flat-space Yang-Mills theories. By applying the biconformal extension to a 4-dim pure Yang-Mills theory with conformal symmetry, we establish a 1-1, onto mapping between a set of gravitational gauge theories and 4-dim, flat-space gauge theories

On using residual risk to assess the cost effectiveness and health protectiveness of remedy selection at superfund sites

International Nuclear Information System (INIS)

Katsumata, Peter T.; Kastenberg, William E.

1998-01-01

This article examines the importance of determining residual risk and its impact on remedy selection at Superfund Sites. Within this examination, risks are assessed using probabilistic models that incorporate the uncertainty and variability of the input parameters, and utilize parameter distributions based on current and applicable site-specific data. Monte Carlo methods are used to propagate these uncertainties and variabilities through the risk calculations resulting in a distribution for the estimate of both risk and residual risk. Such an approach permits an informed decision based on a broad information base which involves considering the entire uncertainty distribution of risk rather than a point estimate for each exposure scenario. Using the probabilistic risk estimates, with current and applicable site-specific data, alternative decisions regarding cleanup are obtained for two Superfund Sites

Influence of rice sample preparation and milling procedures on milling quality appraisals

Science.gov (United States)

The objective of this research was to investigate the effect of sample preparation and milling procedure on milling quality appraisals of rough rice. Samples of freshly harvested medium-grain rice (M202) with different initial moisture contents (MCs) ranging from 20.2% to 25.1% (w.b.) were used for...

Influence of milling process on efavirenz solubility

Directory of Open Access Journals (Sweden)

Erizal Zaini

2017-01-01

Full Text Available Introduction: The aim of this study was to investigate the influence of the milling process on the solubility of efavirenz. Materials and Methods: Milling process was done using Nanomilling for 30, 60, and 180 min. Intact and milled efavirenz were characterized by powder X-ray diffraction, scanning electron microscopy (SEM, spectroscopy infrared (IR, differential scanning calorimetry (DSC, and solubility test. Results: The X-ray diffractogram showed a decline on peak intensity of milled efavirenz compared to intact efavirenz. The SEM graph depicted the change from crystalline to amorphous habit after milling process. The IR spectrum showed there was no difference between intact and milled efavirenz. Thermal analysis which performed by DSC showed a reduction on endothermic peak after milling process which related to decreasing of crystallinity. Solubility test of intact and milled efavirenz was conducted in distilled water free CO2with 0.25% sodium lauryl sulfate media and measured using high-performance liquid chromatography method with acetonitrile: distilled water (80:20 as mobile phases. The solubility was significantly increased (P < 0.05 after milling processes, which the intact efavirenz was 27.12 ± 2.05, while the milled efavirenz for 30, 60, and 180 min were 75.53 ± 1.59, 82.34 ± 1.23, and 104.75 ± 0.96 μg/mL, respectively. Conclusions: Based on the results, the solubility of efavirenz improved after milling process.

Superfund TIO videos: Set B. Community relations, communicating with the media and presenting technical information. Part 9. Audio-Visual

International Nuclear Information System (INIS)

1990-01-01

The videotape is divided into three sections. Section 1 discusses the Superfund Community Relations (CR) Program and its history and objectives. Community Relations requirements as defined by CERCLA for Superfund actions are outlined. Community Relations requirements, the nature of community involvement in CR plans, effective CR techniques, and the roles of the OSC, RPM, and EPA Community Relations Coordinator (CRC) are discussed. Section 2 (1) describes the media's perspective on seeking information; (2) identifies five settings and mechanisms for interacting with the media; (3) offers good media-relations techniques; and (4) lists tips for conducting media interviews. Section 3 outlines techniques for presenting technical information, describes how to be prepared to address typical issues of community concern, and identifies the four key elements in handling tough questions

Tool Wear Analysis on Five-Axis Flank Milling for Curved Shape Part – Full Flute and Ground Shank End Mill

Directory of Open Access Journals (Sweden)

Syahrul Azwan Sundi

2017-01-01

Full Text Available This paper is a study on full flute (extra-long tool and ground shank end mill wear analysis by utilizing five-axis CNC to implement flank milling strategy on curved shape part. Five-axis machining eases the user to implement variations of strategy such as flank milling. Flank milling is different from point milling. Point milling cuts materials by using the tip of the tool whereas the flank milling uses the cutting tool body to cut material. The type of cutting tool used was end mill 10 mm diameter with High Speed Steel (HSS material. One factor at a time was utilized to analyze the overall data. Feed rate and spindle speed were the two main factors that been set up equally for both full flute and ground shank end mill. At the end of this research, the qualitative analysis based on tool wear between full flute and ground shank end mill is observed. Generally, both types of cutting tools showed almost the same failure indication such as broken edge or chipped off edge, formation of pinned hole on the surface and serration formation or built-up edge (BUE on the primary flute. However, the results obtained from the enlarged images which were captured by Optical Microscope indicated that, the ground shank end mill is better than the full flute end mill.

Particle deformation during stirred media milling

Science.gov (United States)

Hamey, Rhye Garrett

Production of high aspect ratio metal flakes is an important part of the paint and coating industry. The United States Army also uses high aspect ratio metal flakes of a specific dimension in obscurant clouds to attenuate infrared radiation. The most common method for their production is by milling a metal powder. Ductile metal particles are initially flattened in the process increasing the aspect ratio. As the process continues, coldwelding of metal flakes can take place increasing the particle size and decreasing the aspect ratio. Extended milling times may also result in fracture leading to a further decrease in the particle size and aspect ratio. Both the coldwelding of the particles and the breakage of the particles are ultimately detrimental to the materials performance. This study utilized characterization techniques, such as, light scattering and image analysis to determine the change in particle size as a function of milling time and parameters. This study proved that a fundamental relationship between the milling parameters and particle deformation could be established by using Hertz's theory to calculate the stress acting on the aluminum particles. The study also demonstrated a method by which milling efficiency could be calculated, based on the amount of energy required to cause particle deformation. The study found that the particle deformation process could be an energy efficient process at short milling times with milling efficiency as high as 80%. Finally, statistical design of experiment was used to obtain a model that related particle deformation to milling parameters, such as, rotation rate and milling media size.

Learning Activity Packets for Milling Machines. Unit I--Introduction to Milling Machines.

Science.gov (United States)

Oklahoma State Board of Vocational and Technical Education, Stillwater. Curriculum and Instructional Materials Center.

This learning activity packet (LAP) outlines the study activities and performance tasks covered in a related curriculum guide on milling machines. The course of study in this LAP is intended to help students learn to identify parts and attachments of vertical and horizontal milling machines, identify work-holding devices, state safety rules, and…

Dyeing studies with henna and madder: A research on effect of tin (II) chloride mordant

OpenAIRE

Yusuf, Mohd; Shahid, Mohammad; Khan, Mohd Ibrahim; Khan, Shafat Ahmad; Khan, Mohd Ali; Mohammad, Faqeer

2015-01-01

The present paper deals with the application of natural dyes extracted from powdered henna (Lawsonia inermis) leaves and madder (Rubia cordifolia) roots on woolen yarn and assessment of effect of stannous chloride mordant on dyeability, color characteristics, fastness properties and antifungal activity of dyed woolen yarn. Sixteen shades have been developed for the characterization of their color characteristics and fastness properties. The color strength (K/S value) has been found to be very...

Region 9 NPL Sites (Superfund Sites 2013)

Science.gov (United States)

NPL site POINT locations for the US EPA Region 9. NPL (National Priorities List) sites are hazardous waste sites that are eligible for extensive long-term cleanup under the Superfund program. Eligibility is determined by a scoring method called Hazard Ranking System. Sites with high scores are listed on the NPL. The majority of the locations are derived from polygon centroids of digitized site boundaries. The remaining locations were generated from address geocoding and digitizing. Area covered by this data set include Arizona, California, Nevada, Hawaii, Guam, American Samoa, Northern Marianas and Trust Territories. Attributes include NPL status codes, NPL industry type codes and environmental indicators. Related table, NPL_Contaminants contains information about contaminated media types and chemicals. This is a one-to-many relate and can be related to the feature class using the relationship classes under the Feature Data Set ENVIRO_CONTAMINANT.

Nanocrystalline TiAl powders synthesized by high-energy ball milling: effects of milling parameters on yield and contamination

International Nuclear Information System (INIS)

Bhattacharya, Prajina; Bellon, Pascal; Averback, Robert S.; Hales, Stephen J.

2004-01-01

High-energy ball milling was employed to produce nanocrystalline Ti-Al powders. As sticking of the powders can be sufficiently severe to result in a near zero yield, emphasis was placed on varying milling conditions so as to increase the yield, while avoiding contamination of the powders. The effects of milling parameters such as milling tools, initial state of the powders and addition of process control agents (PCA's) were investigated. Cyclohexane, stearic acid and titanium hydride were used as PCA's. Milling was conducted either in a Cr-steel vial with C-steel balls, or in a tungsten carbide (WC) vial with WC balls, using either elemental or pre-alloyed powders. Powder samples were characterized using X-ray diffraction, scanning and transmission electron microscopy. In the absence of PCA's mechanical alloying in a WC vial and attrition milling in a Cr-steel vial were shown to lead to satisfactory yields, about 65-80%, without inducing any significant contamination of the powders. The results suggest that sticking of the powders on to the milling tools is correlated with the phase evolution occurring in these powders during milling

Long-Term Groundwater Monitoring Optimization, Clare Water Supply Superfund Site, Permeable Reactive Barrier and Soil Remedy Areas, Clare, Michigan

Science.gov (United States)

This report contains a review of the long-term groundwater monitoring network for the Permeable Reactive Barrier (PRB) and Soil Remedy Areas at the Clare Water Supply Superfund Site in Clare, Michigan.

The progress in the researches for uranium mill tailings cleaning treatment and no-waste uranium ore milling processes

International Nuclear Information System (INIS)

Wang Jintang

1990-01-01

The production of uranium mill tailings and their risk assessment are described. The moethods of uranium mill tailings disposal and management are criticized and the necessity of the researches for uranium mill tailings cleaning treatment and no-wasle uranium ore milling process are demonstrated. The progress for these researches in China and other countries with uranium production is reviewed, and the corresponding conclusions are reported

Regional economic impact assessment: Evaluating remedial alternatives for the Portland Harbor Superfund Site, Portland, Oregon, USA.

Science.gov (United States)

Harrison, David; Coughlin, Conor; Hogan, Dylan; Edwards, Deborah A; Smith, Benjamin C

2018-01-01

The present paper describes a methodology for evaluating impacts of Superfund remedial alternatives on the regional economy in the context of a broader sustainability evaluation. Although economic impact methodology is well established, some applications to Superfund remedial evaluation have created confusion because of seemingly contradictory results. This confusion arises from failure to be explicit about 2 opposing impacts of remediation expenditures: 1) positive regional impacts of spending additional money in the region and 2) negative regional impacts of the need to pay for the expenditures (and thus forgo other expenditures in the region). The present paper provides a template for economic impact assessment that takes both positive and negative impacts into account, thus providing comprehensive estimates of net impacts. The paper also provides a strategy for identifying and estimating major uncertainties in the net impacts. The recommended methodology was applied at the Portland Harbor Superfund Site, located along the Lower Willamette River in Portland, Oregon, USA. The US Environmental Protection Agency (USEPA) developed remedial alternatives that it estimated would cost up to several billion dollars, with construction durations possibly lasting decades. The economic study estimated regional economic impacts-measured in terms of gross regional product (GRP), personal income, population, and employment-for 5 of the USEPA alternatives relative to the "no further action" alternative. Integr Environ Assess Manag 2018;14:32-42. © 2017 The Authors. Integrated Environmental Assessment and Management published by Wiley Periodicals, Inc. on behalf of Society of Environmental Toxicology & Chemistry (SETAC). © 2017 The Authors. Integrated Environmental Assessment and Management published by Wiley Periodicals, Inc. on behalf of Society of Environmental Toxicology & Chemistry (SETAC).

75 FR 49524 - Woodland Mills Corporation, Mill Spring, NC; Notice of Affirmative Determination Regarding...

Science.gov (United States)

2010-08-13

... DEPARTMENT OF LABOR Employment and Training Administration [TA-W-73,695] Woodland Mills Corporation, Mill Spring, NC; Notice of Affirmative Determination Regarding Application for Reconsideration By application dated July 22, 2010, petitioners requested administrative [[Page 49525

Geochemical Characteristics of TP3 Mine Wastes at the Elizabeth Copper Mine Superfund Site, Orange County, Vermont

Science.gov (United States)

Hammarstrom, Jane M.; Piatak, Nadine M.; Seal, Robert R.; Briggs, Paul H.; Meier, Allen L.; Muzik, Timothy L.

2003-01-01

Remediation of the Elizabeth mine Superfund site in the Vermont copper belt poses challenges for balancing environmental restoration goals with issues of historic preservation while adopting cost-effective strategies for site cleanup and long-term maintenance. The waste-rock pile known as TP3, at the headwaters of Copperas Brook, is especially noteworthy in this regard because it is the worst source of surface- and ground-water contamination identified to date, while also being the area of greatest historical significance. The U.S. Geological Survey (USGS) conducted a study of the historic mine-waste piles known as TP3 at the Elizabeth mine Superfund site near South Strafford, Orange County, VT. TP3 is a 12.3-acre (49,780 m2) subarea of the Elizabeth mine site. It is a focus area for historic preservation because it encompasses an early 19th century copperas works as well as waste from late 19th- and 20th century copper mining (Kierstead, 2001). Surface runoff and seeps from TP3 form the headwaters of Copperas Brook. The stream flows down a valley onto flotation tailings from 20th century copper mining operations and enters the West Branch of the Ompompanoosuc River approximately 1 kilometer downstream from the mine site. Shallow drinking water wells down gradient from TP3 exceed drinking water standards for copper and cadmium (Hathaway and others, 2001). The Elizabeth mine was listed as a Superfund site in 2001, mainly because of impacts of acid-mine drainage on the Ompompanoosuc River.

DEMONSTRATION BULLETIN: ADSORPTION-INTEGRATED-REACTION (AIR2000) PROCESS, KSE, INC.

Science.gov (United States)

This Bulletin is a brief description of the AIR2000 technology developed by KSE, Inc., of Amherst, MA. The AIR2000 unit treats air streams containing volatile organic compounds (VOCs). The demonstration occurred at the Stamina Mills superfund site in North Smithfield, RI from Aug...

Black holes with Yang-Mills hair

International Nuclear Information System (INIS)

Kleihaus, B.; Kunz, J.; Sood, A.; Wirschins, M.

1998-01-01

In Einstein-Maxwell theory black holes are uniquely determined by their mass, their charge and their angular momentum. This is no longer true in Einstein-Yang-Mills theory. We discuss sequences of neutral and charged SU(N) Einstein-Yang-Mills black holes, which are static spherically symmetric and asymptotically flat, and which carry Yang-Mills hair. Furthermore, in Einstein-Maxwell theory static black holes are spherically symmetric. We demonstrate that, in contrast, SU(2) Einstein-Yang-Mills theory possesses a sequence of black holes, which are static and only axially symmetric

76 FR 20287 - Superfund Site, New Bedford Harbor, New Bedford, MA: Anchorage Ground and Regulated Navigation Area

Science.gov (United States)

2011-04-12

... may lead to the discovery of a significant environmental impact from this proposed rule. List of... engaged in activities associated with remediation efforts in the New Bedford Harbor Superfund Site... activity can be performed without undue risk to environmental remediation efforts. Requests for waivers...

Pulp mill as an energy producer

International Nuclear Information System (INIS)

Kaulamo, O.

1998-01-01

The recovery boilers of pulp mills are today the most significant producers of wood energy. The power-to-heat ratio of the power plant process, i.e., power yield, is poor in existing applications. In the study, an alternative of improving the power yield of conventional pulp mills significantly was studied by applying solutions used in power plants to a pulp mill. Extensive conversion of wood energy into electricity is possible only in the recovery boiler of the pulp mill and in a large combustion boiler of bark, wood waste and wood chips integrated to this boiler. Hence, the harvest and transports of wood raw materials, i.e. pulp wood and energy wood, are integrated, and the fraction going to cook and the energy wood fraction are separated at the pulp mill. The method guarantees competitive supply of energy wood. As a result a SELLUPOWER mill was designed, where the recovery boiler combusting black liquor and the large power plant boiler combusting energy wood are integrated to one unit and constructed to a power plant process with a high power-to-heat ratio. Necessary technical solutions, project costs and economical feasibility compared to a conventional pulp mill were determined, and the effect of different production-economical parameters was also studied. (orig.)

Colorado's prospectus on uranium milling

International Nuclear Information System (INIS)

Hazle, A.J.; Franz, G.A.; Gamewell, R.

1982-01-01

The first part of this paper will discuss Colorado's control of uranium mill tailings under Titles I and II of the Uranium Mill Tailings Radiation Control Act of 1978. Colorado has a legacy of nine inactive mill sites requiring reclamation under Title I, and two presently active plus a number of new mill proposals which must be regulated in accordance with Title II. Past failures in siting and control on the part of federal jurisdictions have left the state with a heavy legacy requiring extensive effort to address impacts to the state's environment and population. The second part of this paper will discuss the remedial action programme authorized under Public Law 92-314 for Mesa Country, where lack of federal control led to the dispersal of several hundred thousand tons of uranium mill tailings on thousands of properties, including hundreds of homes, schools and other structures. Successful completion of the State efforts under both programmes will depend on a high level of funding and on the maintenance of adequate regulatory standards. (author)

Understanding dental CAD/CAM for restorations - dental milling machines from a mechanical engineering viewpoint. Part A: chairside milling machines.

Science.gov (United States)

Lebon, Nicolas; Tapie, Laurent; Duret, Francois; Attal, Jean-Pierre

2016-01-01

The dental milling machine is an important device in the dental CAD/CAM chain. Nowadays, dental numerical controlled (NC) milling machines are available for dental surgeries (chairside solution). This article provides a mechanical engineering approach to NC milling machines to help dentists understand the involvement of technology in digital dentistry practice. First, some technical concepts and definitions associated with NC milling machines are described from a mechanical engineering viewpoint. The technical and economic criteria of four chairside dental NC milling machines that are available on the market are then described. The technical criteria are focused on the capacities of the embedded technologies of these milling machines to mill both prosthetic materials and types of shape restorations. The economic criteria are focused on investment costs and interoperability with third-party software. The clinical relevance of the technology is assessed in terms of the accuracy and integrity of the restoration.

Optimization Review: Bunker Hill Mining and Metallurgical Complex Superfund Site, Central Treatment Plant (CTP), Kellogg, Shoshone County, Idaho

Science.gov (United States)

The Bunker Hill Mining and Metallurgical Complex Superfund Site includes all areas of the Coeur d’Alene Basin where mining-related contamination occurred and encompasses a 21-square mile “Box” along Interstate 90 surrounding the former smelter complex.

John Stuart Mill: utilitarismo e liberalismo = John Stuart Mill: utilitarianism and liberalism

Directory of Open Access Journals (Sweden)

Simões, Mauro Cardoso

2013-01-01

Full Text Available Meu objetivo, neste trabalho, é investigar a compatibilidade das teses utilitaristas e liberais de John Stuart Mill. Apresentarei, inicialmente, os principais críticos da filosofia moral e política de Mill, para os quais o discípulo de Bentham teria abandonado o utilitarismo ou, ainda, não esclarecido suficientemente seu princípio da liberdade, o que o tornaria um pensador assistemático e inconsistente. Minha tese é contrária a tais interpretações, uma vez que sustenta ser Mill consistente. Em seguida, defenderei uma interpretação do princípio da liberdade e da individualidade, procurando demonstrar que seu utilitarismo é compatível com seu liberalismo

Optimization of FIB milling for rapid NEMS prototyping

DEFF Research Database (Denmark)

Malm, Bjarke; Petersen, Dirch Hjorth; Lei, Anders

2011-01-01

We demonstrate an optimized milling technique to focused ion beam (FIB) milling in template silicon membranes for fast prototyping of nanoelectromechanical systems (NEMS). Using a single-pass milling strategy the highly topology dependent sputtering rate is boosted and shorter milling time...... is achieved. Drift independence is obtained for small critical features using a radial scan strategy, and a back scan routine ensures minimal line width deviation removing redeposited material. Milling a design similar to a nano four-point probe with a pitch down to 400nm we display what optimized FIB milling...

Dyeing studies with henna and madder: A research on effect of tin (II chloride mordant

Directory of Open Access Journals (Sweden)

Mohd Yusuf

2015-01-01

Full Text Available The present paper deals with the application of natural dyes extracted from powdered henna (Lawsonia inermis leaves and madder (Rubia cordifolia roots on woolen yarn and assessment of effect of stannous chloride mordant on dyeability, color characteristics, fastness properties and antifungal activity of dyed woolen yarn. Sixteen shades have been developed for the characterization of their color characteristics and fastness properties. The color strength (K/S value has been found to be very good in all dyed woolen yarn samples. The color fastness with respect to light exposure, washing and rubbing was quite satisfactory for both henna as well as madder dyed samples. Henna leaves extract was found very effective against Candida glabrata both in solution as well as after application on wool substrate but no antifungal activity is reported in case of madder both in solution as well as on wool substrate.

Yang-Mills theory for non-semisimple groups

CERN Document Server

Nuyts, J; Nuyts, Jean; Wu, Tai Tsun

2003-01-01

For semisimple groups, possibly multiplied by U(1)'s, the number of Yang-Mills gauge fields is equal to the number of generators of the group. In this paper, it is shown that, for non-semisimple groups, the number of Yang-Mills fields can be larger. These additional Yang-Mills fields are not irrelevant because they appear in the gauge transformations of the original Yang-Mills fields. Such non-semisimple Yang-Mills theories may lead to physical consequences worth studying. The non-semisimple group with only two generators that do not commute is studied in detail.

Chevron's Panna Maria mill process description

International Nuclear Information System (INIS)

Anon.

1979-01-01

Key features of Chevron's Uranium Mill located near Panna Maria, Texas, are described. The mill is designed to process a nominal 2500 dry tons/day of uranium bearing ore containing 15% uncombined moisture. The following operations at the mill are highlighted: ore receiving, grinding, leaching, countercurrent decantation and tailings disposal, filtering, solvent extraction, solvent stripping, precipitation, drying, and packaging

VOC Control in Kraft Mills; FINAL

International Nuclear Information System (INIS)

Zhu, J.Y.; Chai, X.-S.; Edwards, L.L.; Gu, Y.; Teja, A.S.; Kirkman, A.G.; Pfromm, P.H.; Rezac, M.E.

2001-01-01

The formation of volatile organic compounds (VOCs), such as methanol, in kraft mills has been an environmental concern. Methanol is soluble in water and can increase the biochemical oxygen demand. Furthermore, it can also be released into atmosphere at the process temperatures of kraft mill-streams. The Cluster Rule of the EPA now requires the control of the release of methanol in pulp and paper mills. This research program was conducted to develop a computer simulation tool for mills to predict VOC air emissions. To achieve the objective of the research program, much effort was made in the development of analytical techniques for the analysis of VOC and determination of vapor liquid partitioning coefficient of VOCs in kraft mill-streams using headspace gas chromatography. With the developed analytical tool, methanol formation in alkaline pulping was studied in laboratory to provide benchmark data of the amount of methanol formation in pulping in kraft mills and for the validation of VOC formation and vapor-liquid equilibrium submodels. Several millwide air and liquid samplings were conducted using the analytical tools developed to validate the simulation tool. The VOC predictive simulation model was developed based on the basic chemical engineering concepts, i.e., reaction kinetics, vapor liquid equilibrium, combined with computerized mass and energy balances. Four kraft mill case studies (a continuous digester, two brownstock washing lines, and a pre-evaporator system) are presented and compared with mill measurements. These case studies provide valuable, technical information for issues related to MACT I and MACT II compliance, such as condensate collection and Clean-Condensate-Alternatives (CCA)

Galilean Yang-Mills theory

Energy Technology Data Exchange (ETDEWEB)

Bagchi, Arjun [Center for Theoretical Physics, Massachusetts Institute of Technology,77 Massachusetts Avenue, Cambridge, MA 02139 (United States); Basu, Rudranil [Saha Institute of Nuclear Physics,Block AF, Sector 1, Bidhannagar, Kolkata 700068 (India); Kakkar, Ashish [Indian Institute of Science Education and Research,Dr Homi Bhabha Road, Pashan. Pune 411008 (India); Mehra, Aditya [Indian Institute of Science Education and Research,Dr Homi Bhabha Road, Pashan. Pune 411008 (India); Van Swinderen Institute for Particle Physics and Gravity, University of Groningen, Nijenborgh 4, 9747 AG Groningen (Netherlands)

2016-04-11

We investigate the symmetry structure of the non-relativistic limit of Yang-Mills theories. Generalising previous results in the Galilean limit of electrodynamics, we discover that for Yang-Mills theories there are a variety of limits inside the Galilean regime. We first explicitly work with the SU(2) theory and then generalise to SU(N) for all N, systematising our notation and analysis. We discover that the whole family of limits lead to different sectors of Galilean Yang-Mills theories and the equations of motion in each sector exhibit hitherto undiscovered infinite dimensional symmetries, viz. infinite Galilean Conformal symmetries in D=4. These provide the first examples of interacting Galilean Conformal Field Theories (GCFTs) in D>2.

Galilean Yang-Mills theory

International Nuclear Information System (INIS)

Bagchi, Arjun; Basu, Rudranil; Kakkar, Ashish; Mehra, Aditya

2016-01-01

We investigate the symmetry structure of the non-relativistic limit of Yang-Mills theories. Generalising previous results in the Galilean limit of electrodynamics, we discover that for Yang-Mills theories there are a variety of limits inside the Galilean regime. We first explicitly work with the SU(2) theory and then generalise to SU(N) for all N, systematising our notation and analysis. We discover that the whole family of limits lead to different sectors of Galilean Yang-Mills theories and the equations of motion in each sector exhibit hitherto undiscovered infinite dimensional symmetries, viz. infinite Galilean Conformal symmetries in D=4. These provide the first examples of interacting Galilean Conformal Field Theories (GCFTs) in D>2.

Texture formation in iron particles using mechanical milling with graphite as a milling aid

Energy Technology Data Exchange (ETDEWEB)

Motozuka, S.; Hayashi, K. [Department of Mechanical Engineering, Gifu National College of Technology, 2236-2 Kamimakuwa, Motosu, Gifu 501-0495 (Japan); Tagaya, M. [Department of Materials Science and Technology, Nagaoka University of Technology, 1603-1 Kamitomioka, Nagaoka, Niigata 940-2188 (Japan); Morinaga, M. [Toyota Physical and Chemical Research Institute, 41-1, Yokomichi, Nagakute, Aichi 480-1192 (Japan)

2015-09-15

Crystallographically anisotropic platelet iron particles were successfully prepared using a conventional ball mill with addition of graphite (Gp) particles. The morphological and structural changes resulting from the milling were investigated using scanning electron microscopy and X-ray diffraction. The spherical iron particles were plastically deformed into platelet shapes during the milling. Simultaneously, it is suggested that the size of the Gp particles decreased and adhered as nanoparticles on the surface of the iron particles. The adhered Gp particles affected the plastic deformation behavior of the iron particles: the (001) planes of α-iron were oriented parallel to the particle face, and no preferred in-plane orientation was observed. This study not only details the preparation of soft magnetic metal particles that crystallographically oriented to enhance their magnetic properties but also provides new insight into the activities of the well-established and extensively studied mechanical milling method.

Texture formation in iron particles using mechanical milling with graphite as a milling aid

International Nuclear Information System (INIS)

Motozuka, S.; Hayashi, K.; Tagaya, M.; Morinaga, M.

2015-01-01

Crystallographically anisotropic platelet iron particles were successfully prepared using a conventional ball mill with addition of graphite (Gp) particles. The morphological and structural changes resulting from the milling were investigated using scanning electron microscopy and X-ray diffraction. The spherical iron particles were plastically deformed into platelet shapes during the milling. Simultaneously, it is suggested that the size of the Gp particles decreased and adhered as nanoparticles on the surface of the iron particles. The adhered Gp particles affected the plastic deformation behavior of the iron particles: the (001) planes of α-iron were oriented parallel to the particle face, and no preferred in-plane orientation was observed. This study not only details the preparation of soft magnetic metal particles that crystallographically oriented to enhance their magnetic properties but also provides new insight into the activities of the well-established and extensively studied mechanical milling method

Arsenic Fate, Transport And Stability Study: Groundwater, Surface Water, Soil And Sediment Investigation At Fort Devens Superfund Site

Science.gov (United States)

A field investigation was conducted to examine the distribution of arsenic in groundwater, surface water, and sediments at the Fort Devens Superfund Site. The study area encompassed a portion of plow Shop Pond (Red Cove), which receives groundwater discharge from the aquifer und...

Current uranium mill licensing issues

International Nuclear Information System (INIS)

Scarano, R.A.

1977-01-01

The problems encountered to insure environmentally safe mining and milling of uranium ores are reviewed. Emphasis is placed on the management of tailings resulting from milling operations. It is pointed out that although the concentration of radioactivity in the tailings is relatively low, control measures are necessary because of the large quantities involved and because of the long half-life of the parent radionuclides present. The major concerns with mill tailings are radon release to the atmosphere and isolation of the tailings from the human environment. Since it is anticipated that the amount of tailings created by the year 2000 will be more than an order of magnitude greater than the quantities that have been generated during the past 30 years, it is recommended that all mill tailings storage areas be located remote from public contact and in areas such that disruption and dispersion by natural forces and seepage of toxic materials into ground water systems are reduced to the maximum extent achievable. Technical issues that receive attention during the NRC licensing process for uranium mills and the preparation of environmental impact statements are discussed briefly

Aquatic assessment of the Ely Copper Mine Superfund site, Vershire, Vermont

Science.gov (United States)

Seal, Robert R.; Kiah, Richard G.; Piatak, Nadine M.; Besser, John M.; Coles, James F.; Hammarstrom, Jane M.; Argue, Denise M.; Levitan, Denise M.; Deacon, Jeffrey R.; Ingersoll, Christopher G.

2010-01-01

The Ely Mine, which operated from 1821 to 1905, and its area of downstream impact constitute the Ely Copper Mine Superfund site. The site was placed on the National Priorities List in 2001. The mine comprises underground workings, foundations from historical structures, several waste-rock piles, roast beds associated with the smelting operation, and slag piles resulting from the smelting. The mine site is drained by Ely Brook, which includes several tributaries, one of which drains a series of six ponds. Ely Brook empties into Schoolhouse Brook, which flows 3.3 kilometers and joins the Ompompanoosuc River.

Would John Stuart Mill have regulated pornography?

OpenAIRE

McGlynn, C.; Ward, I.

2014-01-01

John Stuart Mill dominates contemporary pornography debates where he is routinely invoked as an authoritative defence against regulation. This article, by contrast, argues that a broader understanding of Mill's ethical liberalism, his utilitarianism, and his feminism casts doubt over such an assumption. New insights into Mill's approach to sex, sexual activity, and the regulation of prostitution reveal an altogether more nuanced and activist approach. We conclude that John Stuart Mill would a...

Improving milling and production of a dust-producing unit equipped with hammer mills

Energy Technology Data Exchange (ETDEWEB)

Vorotnikov, Ye.G.; Nikiforov, A.A.; Rasputin, O.V.; Sukhunin, V.I.

1982-01-01

This paper presents generalized experience for deriving coarse ground coal dust in hammer mills by providing comparison data on improving efficiency of operation of the unit when switching to a coarser-type grind of the fuel. Need to have more precise formulas to calculate grinding potential of hammer mills when using a coarser grind is shown.

Wear of micro end mills

DEFF Research Database (Denmark)

Bissacco, Giuliano; Hansen, Hans Nørgaard; De Chiffre, Leonardo

2005-01-01

This paper addresses the important issue of wear on micro end mills considering relevant metrological tools for its characterization and quantification. Investigation of wear on micro end mills is particularly difficult and no data are available in the literature. Small worn volumes cause large...... part. For this investigation 200 microns end mills are considered. Visual inspection of the micro tools requires high magnification and depth of focus. 3D reconstruction based on scanning electron microscope (SEM) images and stereo-pair technique is foreseen as a possible method for quantification...

Toward identifying the next generation of superfund and hazardous waste site contaminants.

Science.gov (United States)

Ela, Wendell P; Sedlak, David L; Barlaz, Morton A; Henry, Heather F; Muir, Derek C G; Swackhamer, Deborah L; Weber, Eric J; Arnold, Robert G; Ferguson, P Lee; Field, Jennifer A; Furlong, Edward T; Giesy, John P; Halden, Rolf U; Henry, Tala; Hites, Ronald A; Hornbuckle, Keri C; Howard, Philip H; Luthy, Richard G; Meyer, Anita K; Sáez, A Eduardo; Vom Saal, Frederick S; Vulpe, Chris D; Wiesner, Mark R

2011-01-01

This commentary evolved from a workshop sponsored by the National Institute of Environmental Health Sciences titled "Superfund Contaminants: The Next Generation" held in Tucson, Arizona, in August 2009. All the authors were workshop participants. Our aim was to initiate a dynamic, adaptable process for identifying contaminants of emerging concern (CECs) that are likely to be found in future hazardous waste sites, and to identify the gaps in primary research that cause uncertainty in determining future hazardous waste site contaminants. Superfund-relevant CECs can be characterized by specific attributes: They are persistent, bioaccumulative, toxic, occur in large quantities, and have localized accumulation with a likelihood of exposure. Although still under development and incompletely applied, methods to quantify these attributes can assist in winnowing down the list of candidates from the universe of potential CECs. Unfortunately, significant research gaps exist in detection and quantification, environmental fate and transport, health and risk assessment, and site exploration and remediation for CECs. Addressing these gaps is prerequisite to a preventive approach to generating and managing hazardous waste sites. A need exists for a carefully considered and orchestrated expansion of programmatic and research efforts to identify, evaluate, and manage CECs of hazardous waste site relevance, including developing an evolving list of priority CECs, intensifying the identification and monitoring of likely sites of present or future accumulation of CECs, and implementing efforts that focus on a holistic approach to prevention.

Ball-milling-induced crystallization and ball-milling effect on thermal crystallization kinetics in an amorphous FeMoSiB alloy

International Nuclear Information System (INIS)

Guo, F.Q.; Lu, K.

1997-01-01

Microstructure evolution in a melt-spun amorphous Fe 77.2 Mo 0.8 Si 9 B 13 alloy subjected to high-energy ball milling was investigated by means of X-ray diffraction (XRD), a transmission electron microscope (TEM), and a differential scanning calorimeter (DSC). It was found that during ball milling, crystallization occurs in the amorphous ribbon sample with precipitation of an α-Fe solid solution, and the amorphous sample crystallizes completely into a single α-Fe nanostructure (rather than α-Fe and borides as in the usual thermal crystallization products) when the milling time exceeds 135 hours. The volume fraction of material crystallized was found to be approximately proportional to the milling time. The fully crystallized sample with a single α-Fe nanophase exhibits an intrinsic thermal stability against phase separation upon annealing at high temperatures. The ball-milling effect on the subsequent thermal crystallization of the amorphous phase in an as-milled sample was studied by comparison of the crystallization products and kinetic parameters between the as-quenched amorphous sample and the as-milled sample was studied by comparison of the crystallization products and kinetic parameters between the as-quenched amorphous sample and the as-milled partially crystallized samples. The crystallization temperatures and activation energies for the crystallization processes of the residual amorphous phase were considerably decreased due to ball milling, indicating that ball milling has a significant effect on the depression of thermal stability of the residual amorphous phase

Effects of milling on functional properties of rice flour.

Science.gov (United States)

Kadan, R S; Bryant, R J; Miller, J A

2008-05-01

A commercial long-grain rice flour (CRF) and the flours made by using a pin mill and the Udy mill from the same batch of broken second-head white long-grain rice were evaluated for their particle size and functional properties. The purpose of this study was to compare the commercial rice flour milling method to the pin and Udy milling methods used in our laboratory and pilot plant. The results showed that pin milled flour had more uniform particle size than the other 2 milled flours. The chalky kernels found in broken white milled rice were pulverized more into fines in both Udy milled flour and CRF than in the pin milled flour. The excessive amount of fines in flours affected their functional properties, for example, WSI and their potential usage in the novel foods such as rice breads (RB). The RB made from CRF collapsed more than loaves made from pin milled Cypress long-grain flours.

77 FR 14837 - Bioassay at Uranium Mills

Science.gov (United States)

2012-03-13

... NUCLEAR REGULATORY COMMISSION [NRC-2012-0057] Bioassay at Uranium Mills AGENCY: Nuclear Regulatory..., ``Bioassay at Uranium Mills.'' This guide describes a bioassay program acceptable to the NRC staff for uranium mills and applicable portions of uranium conversion facilities where the possibility of exposure...

Soil Carbon 4 per mille

Science.gov (United States)

Minasny, Budiman; van Wesemael, Bas

2017-04-01

The '4 per mille Soils for Food Security and Climate' was launched at the COP21 aiming to increase global soil organic matter stocks by 4 per mille (or 0.4 %) per year as a compensation for the global emissions of greenhouse gases by anthropogenic sources. This paper surveyed the soil organic carbon (SOC) stock estimates and sequestration potentials from 20 regions in the world (New Zealand, Chile, South Africa, Australia, Tanzania, Indonesia, Kenya, Nigeria, India, China Taiwan, South Korea, China Mainland, United States of America, France, Canada, Belgium, England & Wales, Ireland, Scotland, and Russia) and asked whether the 4 per mille initiative is feasible. This study highlights region specific efforts and scopes for soil carbon sequestration. Reported soil C sequestration rates generally show that under best management practices, 4 per mille or even higher sequestration rates can be accomplished. High C sequestration rates (up to 10 per mille) can be achieved for soils with low initial SOC stock (topsoil less than 30 t C ha-1), and at the first twenty years after implementation of best management practices. In addition, areas that have reached equilibrium but not at their saturation level will not be able to further increase their sequestration. We found that most studies on SOC sequestration globally only consider topsoil (up to 0.3 m depth), as it is considered to be most affected by management techniques. The 4 per mille initiative was based on a blanket calculation of the whole global soil profile C stock, however the potential to increase SOC is mostly on managed agricultural lands. If we consider 4 per mille on global topsoil of agricultural land, SOC sequestration is about 3.6 Gt C per year, which effectively offset 40% of global anthropogenic greenhouse gas emissions. As a strategy for climate change mitigation, soil carbon sequestration buys time over the next ten to twenty years while other effective sequestration and low carbon technologies become

40 CFR 61.142 - Standard for asbestos mills.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 8 2010-07-01 2010-07-01 false Standard for asbestos mills. 61.142... § 61.142 Standard for asbestos mills. (a) Each owner or operator of an asbestos mill shall either discharge no visible emissions to the outside air from that asbestos mill, including fugitive sources, or...

Research Implementation and Quality Assurance Project Plan: An Evaluation of Hyperspectral Remote Sensing Technologies for the Detection of Fugitive Contamination at Selected Superfund Hazardous Waste Sites

Science.gov (United States)

Slonecker, E. Terrence; Fisher, Gary B.

2009-01-01

This project is a research collaboration between the U.S. Environmental Protection Agency (EPA) Office of Inspector General (OIG) and the U.S. Geological Survey (USGS) Eastern Geographic Science Center (EGSC), for the purpose of evaluating the utility of hyperspectral remote sensing technology for post-closure monitoring of residual contamination at delisted and closed hazardous waste sites as defined under the Comprehensive Environmental Response Compensation and Liability Act [CERCLA (also known as 'Superfund')] of 1980 and the Superfund Amendments and Reauthorization Act (SARA) of 1986.

Yang-Mills theory in Coulomb gauge; Yang-Mills-theorie in Coulombeichung

Energy Technology Data Exchange (ETDEWEB)

Feuchter, C.

2006-07-01

In this thesis we study the Yang-Mills vacuum structure by using the functional Schroedinger picture in Coulomb gauge. In particular we discuss the scenario of colour confinement, which was originally formulated by Gribov. After a short introduction, we recall some basic aspects of Yang-Mills theories, its canonical quantization in the Weyl gauge and the functional Schroedinger picture. We then consider the minimal Coulomb gauge and the Gribov problem of the gauge theory. The gauge fixing of the Coulomb gauge is done by using the Faddeev-Popov method, which enables the resolution of the Gauss law - the constraint on physical states. In the third chapter, we variationally solve the stationary Yang-Mills Schroedinger equation in Coulomb gauge for the vacuum state. Therefor we use a vacuum wave functional, which is strongly peaked at the Gribov horizon. The vacuum energy functional is calculated and minimized resulting in a set of coupled Schwinger-Dyson equations for the gluon energy, the ghost and Coulomb form factors and the curvature in gauge orbit space. Using the angular approximation these integral equations have been solved analytically in both the infrared and the ultraviolet regime. The asymptotic analytic solutions in the infrared and ultraviolet regime are reasonably well reproduced by the full numerical solutions of the coupled Schwinger-Dyson equations. In the fourth chapter, we investigate the dependence of the Yang-Mills wave functional in Coulomb gauge on the Faddeev-Popov determinant. (orig.)

76 FR 24479 - In the Matter of the Taylor Lumber and Treating Superfund Site, Sheridan, Oregon, Amendment to...

Science.gov (United States)

2011-05-02

... ENVIRONMENTAL PROTECTION AGENCY [FRL-9300-9] In the Matter of the Taylor Lumber and Treating... Taylor Lumber and Treating Site, which PWPO was acquiring, in exchange for several obligations related to...-553- 0705. Comments should reference the Taylor Lumber and Treating Superfund Site in Sheridan, Oregon...

Uranium mill tailings management practices in Saskatchewan, Canada

International Nuclear Information System (INIS)

Clifton, A.W.; Barsi, R.G.; Melis, L.A.

1984-01-01

Uranium was discovered in Saskatchewan in 1934. The first major mill began operating at Beaverlodge in 1953; two other mills began production in the same area in 1955 and 1957. Waste management measures were limited at the early mills. A new generation of mills was brought into production beginning in 1975 utilizing engineered waste management systems. The paper presents a brief description of the geography and physical environment of northern Saskatchewan, Canada; reviews milling operations and waste managements systems; describes the evolution of waste management systems; and, comments on environmental control measures regulating the industry

Blue-shift in photoluminescence of ion-milled HgCdTe films and relaxation of defects induced by the milling

International Nuclear Information System (INIS)

Pociask, M.; Izhnin, I.I.; Mynbaev, K.D.; Izhnin, A.I.; Dvoretsky, S.A.; Mikhailov, N.N.; Sidorov, Yu.G.; Varavin, V.S.

2010-01-01

Simultaneous measurements of electrical conductivity, the Hall coefficient, and photoluminescence (PL) spectra of ion-milled Hg 1 - x Cd x Te films (x ∼ 0.30 and 0.38) were performed during post-milling ageing of the films at 293 K. In the course of the PL study, a 'relaxation' of the blue-shift of the PL band of ion-milled Hg 0.70 Cd 0.30 Te was observed. The relaxation was caused by the decrease of the electron concentration due to gradual disintegration of defects induced by the milling. It is shown that while ion milling substantially changes the electrical properties of Hg 1 - x Cd x Te, its PL spectrum in the long-term is affected insignificantly.

KSC ADVANCED GROUND BASED FIELD MILL V1

Data.gov (United States)

National Aeronautics and Space Administration — The Advanced Ground Based Field Mill (AGBFM) network consists of 34 (31 operational) field mills located at Kennedy Space Center (KSC), Florida. The field mills...

Loop quantum corrected Einstein Yang-Mills black holes

Science.gov (United States)

Protter, Mason; DeBenedictis, Andrew

2018-05-01

In this paper, we study the homogeneous interiors of black holes possessing SU(2) Yang-Mills fields subject to corrections inspired by loop quantum gravity. The systems studied possess both magnetic and induced electric Yang-Mills fields. We consider the system of equations both with and without Wilson loop corrections to the Yang-Mills potential. The structure of the Yang-Mills Hamiltonian, along with the restriction to homogeneity, allows for an anomaly-free effective quantization. In particular, we study the bounce which replaces the classical singularity and the behavior of the Yang-Mills fields in the quantum corrected interior, which possesses topology R ×S2 . Beyond the bounce, the magnitude of the Yang-Mills electric field asymptotically grows monotonically. This results in an ever-expanding R sector even though the two-sphere volume is asymptotically constant. The results are similar with and without Wilson loop corrections on the Yang-Mills potential.

ROMI 4.0: Updated Rough Mill Simulator

Science.gov (United States)

Timo Grueneberg; R. Edward Thomas; Urs Buehlmann

2012-01-01

In the secondary hardwood industry, rough mills convert hardwood lumber into dimension parts for furniture, cabinets, and other wood products. ROMI 4.0, the US Department of Agriculture Forest Service's ROugh-MIll simulator, is a software package designed to simulate the cut-up of hardwood lumber in rough mills in such a way that a maximum possible component yield...

Optimisation of milling parameters using neural network

Directory of Open Access Journals (Sweden)

Lipski Jerzy

2017-01-01

Full Text Available The purpose of this study was to design and test an intelligent computer software developed with the purpose of increasing average productivity of milling not compromising the design features of the final product. The developed system generates optimal milling parameters based on the extent of tool wear. The introduced optimisation algorithm employs a multilayer model of a milling process developed in the artificial neural network. The input parameters for model training are the following: cutting speed vc, feed per tooth fz and the degree of tool wear measured by means of localised flank wear (VB3. The output parameter is the surface roughness of a machined surface Ra. Since the model in the neural network exhibits good approximation of functional relationships, it was applied to determine optimal milling parameters in changeable tool wear conditions (VB3 and stabilisation of surface roughness parameter Ra. Our solution enables constant control over surface roughness parameters and productivity of milling process after each assessment of tool condition. The recommended parameters, i.e. those which applied in milling ensure desired surface roughness and maximal productivity, are selected from all the parameters generated by the model. The developed software may constitute an expert system supporting a milling machine operator. In addition, the application may be installed on a mobile device (smartphone, connected to a tool wear diagnostics instrument and the machine tool controller in order to supply updated optimal parameters of milling. The presented solution facilitates tool life optimisation and decreasing tool change costs, particularly during prolonged operation.

Properties and sinterability of wet and dry attrition-milled OREOXed powder

International Nuclear Information System (INIS)

Lee, J. W.; Kim, J. H.; Kim, W. K.; Park, K. I.; Lee, J. W.

2001-01-01

The powder properties and sinterability were investigated with the powder prepared by wet and dry attrition milling of OREOX-treated powder. The OREOX-treated powder was prepared from the simulated spent fuel. Powder having less than 1 μm of average particle size could be obtained by dry milling, but not be obtained by wet milling. Thus, specific surface area of dry milled powder was higher than that of wet milled powder. With increasing of milling time, dry milled powder formed dense agglomerate while wet milled powder showed loose agglomerate. The pellets with higher than 95% T.D. of sintered density and larger than 7 μm of grain size were made with the milled powder regardless of milling method. The milling time in wet milling has greatly improved the sinterability. The pellets produced with dry milled powder have higher sintered density and larger grain size

Pavement maintenance procedures with and without milling materials

Directory of Open Access Journals (Sweden)

Rafiqul A. Tarefder

2016-01-01

Full Text Available This study evaluates maintenance treatment followed by different Districts of New Mexico Department of Transportation (NMDOT. In addition, two case studies on the use of old pavement materials, called the “millings”, in maintenance projects are reported. Based on this study, it is observed that none of the Districts have a written procedure for maintenance work. Rather Districts rely on the experience of the maintenance crew for conducting maintenance projects. All Districts prefer to use chip seal for maintenance irrespective of distress conditions of the pavements. Patching and crack sealing are usually done before chip sealing to extend the life of the chip seals. Sand seal, scrub seal, and slurry seal projects are not done by District maintenance crews but by outside contractors. It is also observed that all Districts are interested in using millings in maintenance projects and most have already used millings in at least one maintenance project with some success and failure. Most of the Districts have used coarse fraction of millings in chip seal projects successfully. However, they failed to find a proper way to process the fine fractions of millings. Case Study I shows that fine millings can be used to construct thin overlay when mixed with emulsion in pug mill or hot drums. Case Study II concludes that fine millings can be used as fine/sand seal successfully following the same procedure and using the same equipment as chip seal. Keywords: Millings, Maintenance, Emulsion, Rutting, Pug-mill

Jaduguda uranium mill : rich experiences for future challenges

International Nuclear Information System (INIS)

Beri, K.K.

1991-01-01

India's only uranium milling plant at Jaduguda was commissioned in 1967-68 utilising low grade uranium ore. The flowsheet of the mill and controlling parameters were based on studies done on laboratory and pilot plant scale tests at the Bhabha Atomic Research Centre, Bombay. The mill has worked upto expectation except in few areas where modifications had to be done for smooth production. Apart from this improvements in operating practices have been done based on experience gained in operating the mill, incorporating the recent technological advances. In the recent past, the mill was expanded to increase the installed capacity by 40% and was commissioned in October 1987. The expanded mill has given the desired capacity and is working smoothly. The present paper deals with the experience gained in running the plant for the last 20 years and changes incorporated (author). 4 figs

Indian Americans at Mille Lacs.

Science.gov (United States)

Holbert, Victoria L.; And Others

The Training Center for Community Programs prepared a report on the Mille Lacs (Chippewa) Reservation in Minnesota. Data for the report were from 2 separate sources: a survey conducted by the Training Center with the assistance of the Mille Lacs community action program (1967) and an attitudinal survey conducted by Victoria Holbert during 1969.…

Ground beetle populations near a kraft mill

Energy Technology Data Exchange (ETDEWEB)

Freitag, R.; Hastings, L.; Mercer, W.R.; Smith, A.

1973-02-01

Twenty species of ground beetles (Family Carabidae) and one species of carrion beetle (Family Silphidae) were collected in six stations east of a kraft paper mill in Thunder Bay, Ontario, from May to August, 1971. The beetle population decreased markedly towards the mill. There was no apparent statistical difference in size variation of specimens near the mill and those further away.

21 CFR 515.10 - Medicated feed mill license applications.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Medicated feed mill license applications. 515.10... (CONTINUED) ANIMAL DRUGS, FEEDS, AND RELATED PRODUCTS MEDICATED FEED MILL LICENSE Applications § 515.10 Medicated feed mill license applications. (a) Medicated feed mill license applications (Forms FDA 3448) may...

High-energy ball milling of powder B-C mixtures

International Nuclear Information System (INIS)

Ramos, Alfeu S.; Taguchi, Simone P.; Ramos, Erika C.T.; Arantes, Vera L.; Ribeiro, Sebastiao

2006-01-01

The present work reports on the preparation of B-10 at.% C and B-18 at.% C powders by high-energy ball milling and further heat treatment. The milling process was carried out in a planetary ball mill. Following the milling process, powder samples were heat-treated at 1200 deg. C for 4 h using inert atmosphere. The milled and heat-treated B-10C and B-18C powders were characterized by means of X-ray diffraction (XRD) and scanning electron microscopy (SEM) techniques. A reduction on the intensity of B and C peaks was noticed after milling for 2 h, probably due the fine powder particle sizes because the pronounced fracture mechanism during ball milling of brittle starting components. The XRD patterns of B-10C and B-18C powders milled for 6 h indicated the presence of other peaks, suggesting that a metastable structure could have been formed. After milling for 90 h, these unknown peaks were still present. A large amount of B 4 C was formed after heat treatment at 1200 deg. C for 4 h beside these unknown peaks

The yang mills gravity dual

International Nuclear Information System (INIS)

Crooks, David E.; Evans, Nick

2003-01-01

We describe a ten dimensional supergravity geometry which is dual to a gauge theory that is non-supersymmetric Yang Mills in the infra-red but reverts to N=4 super Yang Mills in the ultra-violet. A brane probe of the geometry shows that the scalar potential of the gauge theory is stable. We discuss the infra-red behaviour of the solution. The geometry describes a Schroedinger equation potential that determines the glueball spectrum of the theory; there is a mass gap and a discrete spectrum. The glueball mass predictions match previous AdS/CFT Correspondence computations in the non-supersymmetric Yang Mills theory, and lattice data, at the 10% level. (author)

Reactive-inspired ball-milling synthesis of an ODS steel: study of the influence of ball-milling and annealing

International Nuclear Information System (INIS)

Brocq, M.

2010-10-01

In the context of the development of new ODS (Oxide Dispersion Strengthened) steels as core materials in future nuclear reactors, we investigated a new process inspired by reactive ball-milling which consists in using YFe 3 andFe 2 O 3 as starting reactants instead of Y 2 O 3 to produce a dispersion of nano-oxides in a steel matrix and the influence of synthesis conditions on the nano-oxide characteristics were studied. For that aim, ODS steels were prepared by ball-milling and then annealed. Multi-scale characterizations were performed after each synthesis step, using notably atom probe tomography and small angle neutron scattering. The process inspired by reactive ball-milling was shown to be efficient for ODS steel synthesis, but it does not modify the nano-oxide characteristics as compared to those of oxides directly incorporated in the matrix by ball-milling. Broadly speaking, the nature of the starting oxygen bearing reactants has no influence on nano-oxide formation. Moreover, we showed that the nucleation of nano-oxides nucleation can start during milling and continues during annealing with a very fast kinetic. The final characteristics of nano-oxides formed in this way can be monitored through ball-milling parameters (intensity, temperature and atmosphere) and annealing parameters (duration and temperature). (author)

Uranium mill tailings remedial action technology

International Nuclear Information System (INIS)

Hartley, J.N.; Gee, G.W.

1984-01-01

The uranium milling process involves the hydrometallurgical extraction of uranium from ores and the resultant generation of large quantities of waste referred to as tailings. Uranium mill tailings have been identified as requiring remediation because they contain residual radioactive material that is not removed in the milling process. Potential radiation exposure can result from direct contact with the tailings, from radon gas emitted by the tailings, and from radioactive contamination of groundwater. As a result, the technology developed under the US Department of Energy (DOE) Uranium Mill Tailings Remedial Action Project (UMTRAP) and the US Nuclear Regulatory Commission (NRC) Uranium Recovery Program have focused on radon control, groundwater contamination and the long-term protection of the containment system. This paper briefly summarizes the UMTRAP and NRC remedial action technology development. 33 references, 9 figures, 5 tables

Uranium mill tailings

International Nuclear Information System (INIS)

McLaren, L.H.

1982-11-01

This bibliography contains information on uranium mill tailings included in the Department of Energy's Energy Data Base from January 1981 through October 1982. The abstracts are grouped by subject category as shown in the table of contents. Entries in the subject index also facilitate access by subject, e.g., Mill Tailings/Radiation Hazards. Within each category the arrangement is by report number for reports, followed by nonreports in reverse chronological order. These citations are to research reports, journal articles, books, patents, theses, and conference papers from worldwide sources. Five indexes, each preceded by a brief description, are provided: Corporate Author, Personal Author, Subject, Contract Number, and Report Number. (335 abstracts)

Geometrical characterization of micro end milling tools

DEFF Research Database (Denmark)

Borsetto, Francesca; Bariani, Paolo; Bissacco, Giuliano

2005-01-01

Performance of the milling process is directly affected by the accuracy of tool geometry. Development of methods suitable for dimensional characterization of such tools, with low measurement uncertainties is therefore of relevance. The present article focuses on the geometrical characterization...... of a flat micro end milling tool with a nominal mill diameter of 200 microns. An experimental investigation was carried out involving two different non-contact systems...

An extended topological Yang-Mills theory

International Nuclear Information System (INIS)

Deguchi, Shinichi

1992-01-01

Introducing infinite number of fields, we construct an extended version of the topological Yang-Mills theory. The properties of the extended topological Yang-Mills theory (ETYMT) are discussed from standpoint of the covariant canonical quantization. It is shown that the ETYMT becomes a cohomological topological field theory or a theory equivalent to a quantum Yang-Mills theory with anti-self-dual constraint according to subsidiary conditions imposed on state-vector space. On the basis of the ETYMT, we may understand a transition from an unbroken phase to a physical phase (broken phase). (author)

Environmental design of a uranium mill

International Nuclear Information System (INIS)

Quan, C.H.; Ring, R.J.; McNaughton, S.J.

2002-01-01

In the frame work of the Cleaner Technology Project for Uranium Mining and Milling, Australian Nuclear and Technology Organization (ANSTO), Environment Division of ANSTO has carried out a programme of research which seeks to identify, investigate and develop cleaner technologies that have the potential to minimize the environmental impact of uranium mining and milling. This paper describes three design options of a new uranium mill that can meet environmental, technical and economical objectives. The feasibility of such an approach was examined in the laboratory and in a pilot plant study. (author)

Contamination risk of stable isotope samples during milling.

Science.gov (United States)

Isaac-Renton, M; Schneider, L; Treydte, K

2016-07-15

Isotope analysis of wood is an important tool in dendrochronology and ecophysiology. Prior to mass spectrometry analysis, wood must be homogenized, and a convenient method involves a ball mill capable of milling samples directly in sample tubes. However, sample-tube plastic can contaminate wood during milling, which could lead to biological misinterpretations. We tested possible contamination of whole wood and cellulose samples during ball-mill homogenization for carbon and oxygen isotope measurements. We used a multi-factorial design with two/three steel milling balls, two sample amounts (10 mg, 40 mg), and two milling times (5 min, 10 min). We further analyzed abrasion by milling empty tubes, and measured the isotope ratios of pure contaminants. A strong risk exists for carbon isotope bias through plastic contamination: the δ(13) C value of polypropylene deviated from the control by -6.77‰. Small fibers from PTFE filter bags used during cellulose extraction also present a risk as the δ(13) C value of this plastic deviated by -5.02‰. Low sample amounts (10 mg) showed highest contamination due to increased abrasion during milling (-1.34‰), which is further concentrated by cellulose extraction (-3.38‰). Oxygen isotope measurements were unaffected. A ball mill can be used to homogenize samples within test tubes prior to oxygen isotope analysis, but not prior to carbon or radiocarbon isotope analysis. There is still a need for a fast, simple and contamination-free sample preparation procedure. Copyright © 2016 John Wiley & Sons, Ltd. Copyright © 2016 John Wiley & Sons, Ltd.

Graphic products used in the evaluation of traditional and emerging remote sensing technologies for the detection of fugitive contamination at selected superfund hazardous waste sites

Science.gov (United States)

Slonecker, E. Terrence; Fisher, Gary B.

2011-01-01

This report presents the overhead imagery and field sampling results used to prepare U.S. Geological Survey Open-File Report 2011-1050, 'Evaluation of Traditional and Emerging Remote Sensing Technologies for the Detection of Fugitive Contamination at Selected Superfund Hazardous Waste Sites'. These graphic products were used in the evaluation of remote sensing technology in postclosure monitoring of hazardous waste sites and represent an ongoing research effort. Soil sampling results presented here were accomplished with field portable x-ray fluoresence (XRF) technology and are used as screening tools only representing the current conditions of metals and other contaminants at selected Superfund hazardous waste sites.

Management of wastes from uranium mines and mills

International Nuclear Information System (INIS)

Thomas, K.T.

1981-01-01

Uranium mining and milling operations have not given rise to much concern about their hazards, and with advancing technologies for mill processing and waste management, the situation will continue to improve. However, the disposal of large quantities of waste produced in mining and milling does have an environmental impact, owing to the long half-lives and the ready availability of the toxic radionuclides Ra-226 and Rn-222. This article deals with the management of wastes from uranium mines and mills

An evaluation of traditional and emerging remote sensing technologies for the detection of fugitive contamination at selected Superfund hazardous waste sites

Science.gov (United States)

Slonecker, E. Terrence; Fisher, Gary B.

2011-01-01

This report represents a remote sensing research effort conducted by the U.S. Geological Survey in cooperation with the U.S. Environmental Protection Agency (EPA) for the EPA Office of Inspector General. The objective of this investigation was to explore the efficacy of remote sensing as a technology for postclosure monitoring of hazardous waste sites as defined under the Comprehensive Environmental Response Compensation and Liability Act of 1980 (Public Law 96-510, 42 U.S.C. §9601 et seq.), also known as \\"Superfund.\\" Five delisted Superfund sites in Maryland and Virginia were imaged with a hyperspectral sensor and visited for collection of soil, water, and spectral samples and inspection of general site conditions. This report evaluates traditional and hyperspectral imagery and field spectroscopic measurement techniques in the characterization and analysis of fugitive (anthropogenic, uncontrolled) contamination at previously remediated hazardous waste disposal sites.

Contingency analysis modeling for superfund sites and other sources. Final report

International Nuclear Information System (INIS)

Christensen, D.; Kaiser, G.D.

1993-01-01

The report provides information on contingency modeling for a wide range of different accidental release scenarios of hazardous air pollutants that might take place at Superfund and other sites. The scenarios are used to illustrate how atmospheric dispersion models, including dense gas models, should be applied. Particular emphasis is made on the input data that is needed for proper applications of models. Flow charts direct the user to specific sections where various scenarios are discussed. A check list of items that should be discussed before running the model is provided. Several examples are provided to specifically show how to apply the models so as to produce a credible analysis for a particular release scenario

DESIGN, PERFORMANCE, AND SUSTAINABILITY OF ENGINEERED COVERS FOR URANIUM MILL TAILINGS

Energy Technology Data Exchange (ETDEWEB)

Waugh, W. Jody

2004-04-21

Final remedies at most uranium mill tailings sites include engineered covers designed to contain metals and radionuclides in the subsurface for hundreds of years. Early cover designs rely on compacted soil layers to limit water infiltration and release of radon, but some of these covers inadvertently created habitats for deep-rooted plants. Root intrusion and soil development increased the saturated hydraulic conductivity several orders of magnitude above design targets. These covers may require high levels of maintenance to sustain long-term performance. Relatively low precipitation, high potential evapotranspiration, and thick unsaturated soils favor long-term hydrologic isolation of buried waste at arid and semiarid sites. Later covers were designed to mimic this natural soil-water balance with the goal of sustaining performance with little or no maintenance. For example, the cover for the Monticello, Utah, Superfund site relies on a thick soil-sponge layer overlying a sand-and-gravel capillary barrier to store precipitation while plants are dormant and on native vegetation to dry the soil sponge during the growing season. Measurements of both off-site caisson lysimeters and a large 3-ha lysimeter built into the final cover show that drainage has been well below a U.S. Environmental Protection Agency target of less than 3.0 mm/yr. Our stewardship strategy combines monitoring precursors to failure, probabilistic riskbased modeling, and characterization of natural analogs to project performance of covers for a range of possible future environmental scenarios. Natural analogs are needed to understand how ecological processes will influence cover performance, processes that cannot be predicted with short-term monitoring and existing numerical models.

78 FR 31315 - Kraft Pulp Mills NSPS Review

Science.gov (United States)

2013-05-23

... Kraft Pulp Mills NSPS Review; Proposed Rule #0;#0;Federal Register / Vol. 78 , No. 100 / Thursday, May...-OAR-2012-0640; FRL-9815-9] RIN 2060-AR64 Kraft Pulp Mills NSPS Review AGENCY: Environmental Protection... performance standards for kraft pulp mills. These revised standards include particulate matter emission limits...

Uranium mining and milling

International Nuclear Information System (INIS)

Floeter, W.

1976-01-01

In this report uranium mining and milling are reviewed. The fuel cycle, different types of uranium geological deposits, blending of ores, open cast and underground mining, the mining cost and radiation protection in mines are treated in the first part of this report. In the second part, the milling of uranium ores is treated, including process technology, acid and alkaline leaching, process design for physical and chemical treatment of the ores, and the cost. Each chapter is clarified by added figures, diagrams, tables, and flowsheets. (HK) [de

Improved oral bioavailability of probucol by dry media-milling.

Science.gov (United States)

Li, Jia; Yang, Yan; Zhao, Meihui; Xu, Hui; Ma, Junyuan; Wang, Shaoning

2017-09-01

The polymer/probucol co-milled mixtures were prepared to improve drug dissolution rate and oral bioavailability. Probucol, a BCS II drug, was co-milled together with Copovidone (Kollidon VA64, VA64), Soluplus, or MCC using the dry media-milling process with planetary ball-milling equipment. The properties of the milled mixtures including morphology, crystal form, vitro drug dissolution and in vivo oral bioavailability in rats were evaluated. Probucol existed as an amorphous in the matrix of the co-milled mixtures containing VA64, which helped to enhance drug dissolution. The ternary mixture composed of VA64, RH40, and probucol showed increased dissolution rates in both sink and non-sink conditions. It also had a higher oral bioavailability compared to the reference formulation. Dry-media milling of binary or ternary mixtures composed of drug, polymer and surfactant possibly have wide applications to improve dissolution rate and oral bioavailability of water-insoluble drugs. Copyright © 2017 Elsevier B.V. All rights reserved.

PENGARUH TEKNIK PENYAYATAN PAHAT MILLING PADA CNC MILLING 3 AXIS TERHADAP TINGKAT KEKASARAN PERMUKAAN BENDA BERKONTUR

Directory of Open Access Journals (Sweden)

Irawan Irawan

2016-06-01

Full Text Available Dalam perindustrian penggunaan mesin CNC Milling sangat di andalkan untuk mendapatkan hasil yang optimum baik secara kualitas maupun kuantitas. Akan tetapi muncul permasalahan,bagaimana pengaruh perbedaan teknik penyayatan terhadap nilai kekasaran permukaan benda kerja berkontur dalam proses milling CNC. Penelitian ini bertujuan untuk mengetahui pengaruh metode penyayatan pahat milling terhadap kekasaran permukaan benda kerja berkontur yang di hasilkan pada proses freis dengan menggunakan mesin milling CNC - 3Axis Makino S33. Peneliitan ini merancang dan membuat molding Cover stop kontak dikarenakan permukaan produk cover stop kontak memiliki permukaan yang berkontur. Molding ini terdiri dari Core dan Cavity. Benda kerja yang akan di ujicoba adalah bagian Core sebanyak 3 buah. Dalam pengerjaanya benda ujicoba diberikan perlakuan yang sama antara lain, kedalaman pemotongan, kecepatan spindle, dan jenis pahat yang di gunakan, kemudian dari ke 3 benda kerja tersebut masing- masing di tentukan 3 titik pengukuran. Dari hasil pengujian yang di peroleh kemudian dilakukan analisis tabel. Nilai kekasaran permukaan terendah (rata-rata kekasaran 0.899µ m dengan waktu permesinan tercepat (waktu proses 1 jam 08 menit pada penggunaan metode penyayatan 3D offset finishing. Penulis menyarankan agar dalam proses freis menggunakan mesin milling CNC 3Axis Makino S33 pada permukaan benda yang berkontur, untuk mendapatkan nilai kekasaran yang terendah disarankan menggunakan metode penyayatan 3D offset finishing.

Model Predictive Control for an Industrial SAG Mill

DEFF Research Database (Denmark)

Ohan, Valeriu; Steinke, Florian; Metzger, Michael

2012-01-01

identication. When applied to MIMO systems we call this controller a MIMO-ARX based MPC. We use an industrial Semi-Autogenous Grinding (SAG) mill to illustrate the performance of this controller. SAG mills are the primary units in a grinding chain and also the most power consuming units. Therefore, improved...... control of SAG mills has the potential to signicantly improve eciency and reduce the specic energy consumption for mineral processes. Grinding circuits involving SAG mills are multivariate processes. Commissioning of a control system based on a classical single-loop controllers with logic is time...

Completion of the uranium mill tailings remedial project and cleanup of the former mill site at Grand Junction, Colorado

International Nuclear Information System (INIS)

Rael, G.J.; Cox, S.W.; Artiglia, E.W.

2000-01-01

The United States Department of Energy's Uranium Mill Tailings Remedial Action (UMTRA) Surface Project has successfully completed the cleanup of 22 former uranium mill sites, more than 5400 vicinity properties, and has constructed 18 entombment cells. The Project has recently received the United States Nuclear Regulatory Commission's approval and certification for the last two disposal sites, with these sites being placed under the general license for long term custodial care of residual radioactive material. The UMTRA site located at Grand Junction, Colorado is a good example of the technical, political, economic, and public relations challenges that were overcome in achieving success. The UMTRA Team discussed, negotiated, planned, and eventually acted on this uranium mill tailings problem and brought the project to a successful conclusion for the community. From the early 1940s through the 1970s, uranium ore was mined in significant quantities under United States federal contracts for the government's national defence programmes, i.e. the Manhattan Engineering District and Atomic Energy Commission programmes. The problem started as the need for uranium decreased in the late 1960s, resulting in mills shutting down, leaving behind large quantities of process waste tailings and contaminated mill buildings. The former Climax Uranium Company mill site in Grand Junction was one of the largest of these sites. (author)

7 CFR 868.301 - Definition of milled rice.

Science.gov (United States)

2010-01-01

... 7 Agriculture 7 2010-01-01 2010-01-01 false Definition of milled rice. 868.301 Section 868.301... FOR CERTAIN AGRICULTURAL COMMODITIES United States Standards for Milled Rice Terms Defined § 868.301 Definition of milled rice. Whole or broken kernels of rice (Oryza sativa L.) from which the hulls and at...

Effect of Milling Time on the Microstructure, Physical and Mechanical Properties of Al-Al₂O₃ Nanocomposite Synthesized by Ball Milling and Powder Metallurgy.

Science.gov (United States)

Toozandehjani, Meysam; Matori, Khamirul Amin; Ostovan, Farhad; Abdul Aziz, Sidek; Mamat, Md Shuhazlly

2017-10-26

The effect of milling time on the morphology, microstructure, physical and mechanical properties of pure Al-5 wt % Al₂O₃ (Al-5Al₂O₃) has been investigated. Al-5Al₂O₃ nanocomposites were fabricated using ball milling in a powder metallurgy route. The increase in the milling time resulted in the homogenous dispersion of 5 wt % Al₂O₃ nanoparticles, the reduction of particle clustering, and the reduction of distances between the composite particles. The significant grain refining during milling was revealed which showed as a reduction of particle size resulting from longer milling time. X-Ray diffraction (XRD) analysis of the nanocomposite powders also showed that designated ball milling contributes to the crystalline refining and accumulation of internal stress due to induced severe plastic deformation of the particles. It can be argued that these morphological and microstructural variations of nanocomposite powders induced by designated ball milling time was found to contribute to an improvement in the density, densification, micro-hardness ( HV ), nano-hardness ( HN ), and Young's modulus ( E ) of Al-5Al₂O₃ nanocomposites. HV , HN , and E values of nanocomposites were increased by ~48%, 46%, and 40%, after 12 h of milling, respectively.

Fault Detection in Coal Mills used in Power Plants

DEFF Research Database (Denmark)

Odgaard, Peter Fogh; Mataji, Babak

2006-01-01

In order to achieve high performance and efficiency of coal-fired power plants, it is highly important to control the coal flow into the furnace in the power plant. This means suppression of disturbances and force the coal mill to deliver the required coal flow, as well as monitor the coal mill...... in order to detect faults in the coal mill when they emerge. This paper deals with the second objective. Based on a simple dynamic model of the energy balance a residual is formed for the coal mill. An optimal unknown input observer is designed to estimate this residual. The estimated residual is following...... tested on measured data of a fault in a coal mill, it can hereby be concluded that this residual is very useful for detecting faults in the coal mill....

Analytical Prediction of Three Dimensional Chatter Stability in Milling

Science.gov (United States)

Altintas, Yusuf

The chip regeneration mechanism during chatter is influenced by vibrations in three directions when milling cutters with ball end, bull nose, or inclined cutting edges are used. A three dimensional chatter stability is modeled analytically in this article. The dynamic milling system is formulated as a function of cutter geometry, the frequency response of the machine tool structure at the cutting zone in three Cartesian directions, cutter engagement conditions and material property. The dynamic milling system with nonlinearities and periodic delayed differential equations is reduced to a three dimensional linear stability problem by approximations based on the physics of milling. The chatter stability lobes are predicted in the frequency domain using the proposed analytical solution, and verified experimentally in milling a Titanium alloy with a face milling cutter having circular inserts.

Replacing chemicals in recycle mills with mechanical alternatives

Energy Technology Data Exchange (ETDEWEB)

Institute of Paper Science Technology

2002-07-01

A high-intensity spark fired underwater decomposes a small amount of the water into hydroxyl radicals, which are strong oxidants. These are able to oxidize contaminants such as glue and wood pitch that enter paper recycling mills as a part of the incoming furnish and cost the industry several hundred million dollars. The sparking technique is safe, inexpensive, and is capable of treating large volumes of water, which makes it attractive for mill applications. Several mill trials were run. Sparking caused a decrease in the tack of the deposits in one case. Lower bleach use occurred in two other mills; sparking reduced the degree of ink reattachment to fiber. The payback for either application is attractive. Sparking induced deposition of contaminants in another mill, which is a positive development--if it can be controlled. The technique is also able to degas water and to oxidize odor-causing sulfur compounds. Although one unit has been purchased by a mill, second-order effects caused by the technology needs to be defined further before the technology can be broadly applied.

Phase Transitions in Mechanically Milled Mn-Al-C Permanent Magnets

Directory of Open Access Journals (Sweden)

Michael J. Lucis

2014-04-01

Full Text Available Mn-Al powders were prepared by rapid solidification followed by high-energy mechanical milling. The rapid solidification resulted in single-phase ε. The milling was performed in both the ε phase and the τ phase, with the τ-phase formation accomplished through a heat treatment at 500 °C for 10 min. For the ε-milled samples, the conversion of the ε to the τ phase was accomplished after milling via the same heat treatment. Mechanical milling induced a significant increase in coercivity in both cases, reaching 4.5 kOe and 4.1 kOe, respectively, followed by a decrease upon further milling. The increase in coercivity was the result of grain refinement induced by the high-energy mechanical milling. Additionally, in both cases a loss in magnetization was observed. Milling in the ε phase showed a smaller decrease in the magnetization due to a higher content of the τ phase. The loss in magnetization was attributed to a stress-induced transition to the equilibrium phases, as no site disorder or oxidation was observed. Surfactant-assisted milling in oleic acid also improved coercivity, but in this case values reached >4 kOe and remained stable at least through 32 h of milling.

Practitioner Profile: An Interview With Amanda Mills

Directory of Open Access Journals (Sweden)

Amanda Mills

2012-01-01

Full Text Available For more than 25 years, Amanda Mills has been working with arts organizations across Canada and with artists of all kinds to assist them in achieving financial sanity. She has taught business management at the University of Victoria and has prepared thousands of tax returns for writers, visual artists, choreographers, actors, filmmakers, broadcasters, and creative entrepreneurs. Ten years ago, bringing together her work on trauma, with twenty years of business management, Mills founded Loose Change Financial Therapy – the place where money and feelings meet. Mills has presented Loose Change workshops for social workers, teachers, psychotherapists, artists, anti-poverty activists, sex trade workers, women’s groups, and the general public.  She has been a guest on major Canadian radio and television broadcasts and profiled in many major Canadian newspapers and periodicals. Mills is also a crisis counselor and co-wrote a bestselling book on recovering from trauma. A tax professional and business manager, she is certified as a financial counselor under the Bankruptcy and Insolvency Act. Mills is also currently completing a certificate in mediation.

GEOMETRICAL CHARACTERIZATION OF MICRO END MILLING TOOLS

DEFF Research Database (Denmark)

Borsetto, Francesca; Bariani, Paolo

The milling process is one of the most common metal removal operation used in industry. This machining process is well known since the beginning of last century and has experienced, along the years, many improvements of the basic technology, as concerns tools, machine tools, coolants/lubricants, ......The milling process is one of the most common metal removal operation used in industry. This machining process is well known since the beginning of last century and has experienced, along the years, many improvements of the basic technology, as concerns tools, machine tools, coolants....../lubricants, milling strategies and controls. Moreover the accuracy of tool geometry directly affects the performance of the milling process influencing the dimensional tolerances of the machined part, the surface topography, the chip formation, the cutting forces and the tool-life. The dimensions of certain...... geometrical details, as for instance the cutting edge radius, are determined by characteristics of the manufacturing process, tool material, coating etc. While for conventional size end mills the basic tool manufacturing process is well established, the reduction of the size of the tools required...

Final Report; Arsenic Fate, Transport and Stability Study; Groundwater, Surface Water, Soil And Sediment Investigation, Fort Devens Superfund Site, Devens, Massachusetts

Science.gov (United States)

This document presents results from the Fiscal Years 2006-2008 field investigation at the Fort Devens Superfund Site, Operable Unit 1 (Shepley's Hill Landfill) to fulfill the research objectives outlined in the proposal entitled, 'Fate and Transport of Arsenic in an Urban, Milita...

EPA's role in uranium mining and milling

International Nuclear Information System (INIS)

Smith, P.B.

1980-01-01

EPA's role and actions in regulating uranium mining and milling are reviewed and updated. Special emphasis is given to EPA's current activities under the Uranium Mill Tailings Radiation Control Act of 1978

Reclamation of uranium mining and milling disturbances

International Nuclear Information System (INIS)

Farmer, E.E.; Schuman, G.E.

1987-01-01

Since 1945 the history of uranium mining and milling in the US has been a story of wide fluctuations in market prices and in mining and milling capacity. The late 1960's and the 1970's saw a sizeable reduction in the production of yellowcake because of an earlier over-supply, a leveling off of the military demand, and a failure of the nuclear electric power industry to create the anticipated commercial demand. The decline in the domestic production of yellowcake has continued through the early 1980's to the present. Today, there are five operating uranium mills in the US: one in Wyoming, two in Utah, one in New Mexico, and one in Texas. Of these five mills, three are operating on a reduced schedule, as little as three days a month. A significant portion of the current US production of uranium goes overseas to fulfill Japanese, French, and other European contracts. There is still a sizeable reclamation job to be accomplished on old uranium wastes, both tailings impoundments and overburden embankments. Before the Uranium Mill Tailings Control Act of 1978 (PL 95-604), reclamation was frequently omitted altogether, or else done in a haphazard fashion. We do not know the total area of unreclaimed, radioactive, uranium overburden wastes in the western US, but the area is large, probably several thousand hectares. Fortunately, these overburden wastes are almost entirely located in remote areas. Mill tailings are more difficult to reclaim than overburden, and tailings represent a more serious health hazards. There are approximately 25 million metric tons of unreclaimed uranium mill tailings, with variable health hazards, located in the US

Understanding dental CAD/CAM for restorations--dental milling machines from a mechanical engineering viewpoint. Part B: labside milling machines.

Science.gov (United States)

Lebon, Nicolas; Tapie, Laurent; Duret, Francois; Attal, Jean-Pierre

2016-01-01

Nowadays, dental numerical controlled (NC) milling machines are available for dental laboratories (labside solution) and dental production centers. This article provides a mechanical engineering approach to NC milling machines to help dental technicians understand the involvement of technology in digital dentistry practice. The technical and economic criteria are described for four labside and two production center dental NC milling machines available on the market. The technical criteria are focused on the capacities of the embedded technologies of milling machines to mill prosthetic materials and various restoration shapes. The economic criteria are focused on investment cost and interoperability with third-party software. The clinical relevance of the technology is discussed through the accuracy and integrity of the restoration. It can be asserted that dental production center milling machines offer a wider range of materials and types of restoration shapes than labside solutions, while labside solutions offer a wider range than chairside solutions. The accuracy and integrity of restorations may be improved as a function of the embedded technologies provided. However, the more complex the technical solutions available, the more skilled the user must be. Investment cost and interoperability with third-party software increase according to the quality of the embedded technologies implemented. Each private dental practice may decide which fabrication option to use depending on the scope of the practice.

( Rosa damascena Mill.) by microbial inoculation

African Journals Online (AJOL)

This study was carried out to determine the effects of microbial inoculation in breaking seed dormancy and on the germination of Rosa damascena Mill. Seeds of R. damascena Mill. are the most used scented rose species in rose oil production. The most important production centers around the world are Turkey and ...

Yang-Mills analogs of general-relativistic solutions

International Nuclear Information System (INIS)

Singlton, D.

1998-01-01

Some solutions of Yang-Mills equations, which can be found with the use of the general relativistic theory and Yang-Mills theory, are discussed. Some notes concerning possible physical sense of these solutions are made. Arguments showing that some of such solutions in the Yang-Mills theory (similar to the general relativistic ones) may be connected with the confinement phenomenon are given in particular. The motion of probe particles located into the phonon potential similar to the Schwarz-Child one is briefly discussed for this purpose [ru

Milling and dispersion of multi-walled carbon nanotubes in texanol

Science.gov (United States)

Darsono, Nono; Yoon, Dang-Hyok; Kim, Jaemyung

2008-03-01

Rheological results were used to determine the optimum type of dispersant and its concentration for six commercial dispersants for the dispersion of multi-walled carbon nanotube (MWCNT) agglomerates in texanol. An unsaturated polycarboxylic acid copolymer (BYK P-104) exhibited the optimum performance with the lowest MWCNT slurry viscosity in texanol. The cutting and dispersion efficiencies of MWCNTs with 20 wt.% of BYK P-104 dispersant were compared using conventional ball milling and high energy milling, whereby the latter was found to be more effective. High energy milling for 2 h produced a large portion of MWCNT agglomerates smaller than 150 nm, showing a drastic increase in slurry viscosity due to the dispersion into individual CNTs. On the other hand, 120 h ball milling was required to achieve the agglomerate size of 300 nm with less viscosity increase upon milling. Decrease in the degree of MWCNT crystallinity was observed by both milling, even though 2 h high energy milling showed slightly less damage than 120 h ball milling based on XRD and Raman spectroscopy results.

Milling damage on Carbon Fibre Reinforced Polymer using TiAlN coated End mills

International Nuclear Information System (INIS)

Konneh, Mohamed; Kassim, Abdullah Abdul Rahman; Izman, Sudin

2015-01-01

This paper reports on the damage caused by milling Carbon Fibre Reinforced Composite (CFRP) with 2-flute 4 mm-diameter solid carbide end mills, coated with titanium aluminium nitride. The machining parameters considered in work are, rotation speed, feed rate and depth of cut. Experiments were designed based on Box-Behnken design and the experiments conducted on a Mikrotool DT-110 CNC micro machine. A laser tachometer was used to ascertain a rotational speed for conducting any machining trial. Optical microscopy examination reveals minimum delamination value of 4.05 mm at the spindle speed of 25,000 rpm, depth of cut of 50μm and feed rate of 3 mm/min and the maximum delamination value of 5.04 mm at the spindle speed of 35000 rpm, depth of cut of 150μm and feed rate of 9 mm/min A mathematical model relating the milling parameters and delamination has been established. (paper)

Milling damage on Carbon Fibre Reinforced Polymer using TiAlN coated End mills

Science.gov (United States)

Konneh, Mohamed; Izman, Sudin; Rahman Kassim, Abdullah Abdul

2015-07-01

This paper reports on the damage caused by milling Carbon Fibre Reinforced Composite (CFRP) with 2-flute 4 mm-diameter solid carbide end mills, coated with titanium aluminium nitride. The machining parameters considered in work are, rotation speed, feed rate and depth of cut. Experiments were designed based on Box-Behnken design and the experiments conducted on a Mikrotool DT-110 CNC micro machine. A laser tachometer was used to ascertain a rotational speed for conducting any machining trial. Optical microscopy examination reveals minimum delamination value of 4.05 mm at the spindle speed of 25,000 rpm, depth of cut of 50μm and feed rate of 3 mm/min and the maximum delamination value of 5.04 mm at the spindle speed of 35000 rpm, depth of cut of 150μm and feed rate of 9 mm/min A mathematical model relating the milling parameters and delamination has been established.

Nanograin formation in milled MoO3 powders

International Nuclear Information System (INIS)

Guerrero-Paz, J; Dorantes-Rosales, H; Aguilar-Martínez, J A; Garibay-Febles, V

2013-01-01

Powder of Molybdenum trioxide was milled for different times in horizontal ball mills. Such powder was characterized by TEM and XRD. Powder was rapidly de-agglomerated and fragmented up to attain nanoplates of two types, amorphous and crystalline. Finally, cold-welding of nanoplates occurred permitting some relaxation process to obtain a more stable energized structure consisting of equiaxial crystalline nanograins after 16 hours of milling.

40 CFR 63.1347 - Standards for raw and finish mills.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 11 2010-07-01 2010-07-01 true Standards for raw and finish mills. 63... and Operating Limits § 63.1347 Standards for raw and finish mills. The owner or operator of each new or existing raw mill or finish mill at a facility which is a major source subject to the provisions...

Peculiarities of binding composition production in vortex jet mill

Science.gov (United States)

Zagorodnyuk, L. Kh; Lesovik, V. S.; Sumskoy, D. A.; Elistratkin, M. Yu; Makhortov, D. S.

2018-03-01

The article investigates the disintegration of perlite production waste in a vortex jet mill; the regularities of milling were established. Binding compositions were obtained at different ratios of cement vs. perlite sand production waste in the vortex jet mill in various milling regimes. The peculiarities of milling processes were studied, and technological and physicomechanical properties of the binding compositions were determined as well. The microstructure of the cement stones made of activated Portland cement and binding compositions in the vortex jet mill was elucidated by electron microscopy. The open pores of the cement-binding compositions prepared using perlite fillers were found to be filled by newgrowths at different stages of collective growth. The microstructure of the binding compositions is dense due to rationally proportioned composition, effective mineral filler— perlite waste — that creates additional substrates for internal composite microstructure formation, mechanochemical activation of raw mixture, which allows obtaining composites with required properties.

Modeling the milling tool wear by using an evolutionary SVM-based model from milling runs experimental data

Science.gov (United States)

Nieto, Paulino José García; García-Gonzalo, Esperanza; Vilán, José Antonio Vilán; Robleda, Abraham Segade

2015-12-01

The main aim of this research work is to build a new practical hybrid regression model to predict the milling tool wear in a regular cut as well as entry cut and exit cut of a milling tool. The model was based on Particle Swarm Optimization (PSO) in combination with support vector machines (SVMs). This optimization mechanism involved kernel parameter setting in the SVM training procedure, which significantly influences the regression accuracy. Bearing this in mind, a PSO-SVM-based model, which is based on the statistical learning theory, was successfully used here to predict the milling tool flank wear (output variable) as a function of the following input variables: the time duration of experiment, depth of cut, feed, type of material, etc. To accomplish the objective of this study, the experimental dataset represents experiments from runs on a milling machine under various operating conditions. In this way, data sampled by three different types of sensors (acoustic emission sensor, vibration sensor and current sensor) were acquired at several positions. A second aim is to determine the factors with the greatest bearing on the milling tool flank wear with a view to proposing milling machine's improvements. Firstly, this hybrid PSO-SVM-based regression model captures the main perception of statistical learning theory in order to obtain a good prediction of the dependence among the flank wear (output variable) and input variables (time, depth of cut, feed, etc.). Indeed, regression with optimal hyperparameters was performed and a determination coefficient of 0.95 was obtained. The agreement of this model with experimental data confirmed its good performance. Secondly, the main advantages of this PSO-SVM-based model are its capacity to produce a simple, easy-to-interpret model, its ability to estimate the contributions of the input variables, and its computational efficiency. Finally, the main conclusions of this study are exposed.

TECHNOLOGY EVALUATION REPORT, SITE PROGRAM DEMONSTRATION TEST: SHIRCO PILOT-SCALE INFRARED INCINERATION SYSTEM ROSE TOWNSHIP DEMODE ROAD SUPERFUND SITE - VOLUME II

Science.gov (United States)

The performance of the Shirco pilot-scale infrared thermal destruction system has been evaluated at the Rose Township, Demode Road Superfund Site and is presented in the report. The waste tested consisted of solvents, organics and heavy metals in an illegal dump site. Volume I gi...

77 FR 43369 - Alumax Mill Products, Inc. Doing Business as Alcoa Mill Products Texarkana a Subsidiary of Alcoa...

Science.gov (United States)

2012-07-24

... Products, Inc., a subsidiary of Alcoa, Inc. The intent of the Department's certification is to properly... DEPARTMENT OF LABOR Employment and Training Administration [TA-W-71,149] Alumax Mill Products, Inc. Doing Business as Alcoa Mill Products Texarkana a Subsidiary of Alcoa, Inc. Nash, TX; Amended...

46 CFR 50.25-3 - Manufacturer or mill certification.

Science.gov (United States)

2010-10-01

... 46 Shipping 2 2010-10-01 2010-10-01 false Manufacturer or mill certification. 50.25-3 Section 50... PROVISIONS Acceptance of Material and Piping Components § 50.25-3 Manufacturer or mill certification. (a) A manufacturer or mill producing materials used in certain products for installation on inspected vessels, shall...

Radiation health and safety aspects in uranium milling

International Nuclear Information System (INIS)

Smart, B.C.

1982-01-01

This presentation deals mainly with radiation levels associated with the uranium milling operations, including yellowcake production. The regulation of uranium mills has not received much attention in the past because radiation levels have been generally low, and uranium milling has been substantially free of occupational illness. More attention is being directed towards minimizing exposures, and the Canadian Atomic Energy Control Board is working on new regulations which will reflect the recommendations of various hearings and the International Commission on Radiological Protection. Emphasis is now being placed on improving monitoring methods. At the beginning of 1982 a gamma dosimetry program will be put into effect for all uranium mine and mill workers. An improved method is also being sought to determine radon daughter exposures more accurately. It is expected that a better knowledge of monitoring and assessing thoron daughter levels in mine and mill facilities will be obtained soon. This radiation contribution will be included when calculating a combined radiation exposure factor for individual workers. Programs are underway to better monitor and assess uranium dust inhalation. Initial studies indicate that the present precautions taken to avoid dust inhalation at the mills are effective. A more complete study will be undertaken in 1982

Determination of the Tapping Part Diameter of the Thread Mill

Directory of Open Access Journals (Sweden)

A. E. Dreval'

2015-01-01

Full Text Available Currently, there is a tendency to increase the proportion of thread milling operations, among other ways of tapping, which is associated with increasing number of CNC machines, flexibility and versatility of the process.Developments presently existing in the RF and used in the thread mills deal, mainly, with the thread milling cutter designs, to process internal and external thread with straight flutes made from high-speed steel.The paper presents a technique to calculate and select the initial design parameters, i.e. the external diameter of the tapping part of thread milling cutter, which is chosen as a basic computational design. The analysis of directories of tool companies containing foreign de-signs of solid thread end-milling cutters has shown that most of them rep-resent the thread cutter designs made of solid carbide. There are solid and interlocking side milling cutters, which use a tapping part both as a single-disk and as a multi-disk one; chip flutes are made to be both as direct and as screw; solid designs of cutters are made from carbide with a diameter of up to 20 ... 25 mm; thread cutters can be left- and right-hand cutting; Designs of the combined thread mills are proposed; internal channels are used for coolant supply.It is shown that the purpose of the external diameter of the tapping part of the thread mill should take into account the effect of the thread mill diameter on the milling process performance, precision of thread profile received, taper thread, tool strength, and the volume of flutes.The analysis has shown that when choosing the external diameter of the thread mill it worth taking its maximum diameter to improve the char-acteristics of the process under the restrictions imposed on the accuracy of the formed thread.

Radiological health aspects of uranium milling

International Nuclear Information System (INIS)

Fisher, D.R.; Stoetzel, G.A.

1983-05-01

This report describes the operation of conventional and unconventional uranium milling processes, the potential for occupational exposure to ionizing radiation at the mill, methods for radiological safety, methods of evaluating occupational radiation exposures, and current government regulations for protecting workers and ensuring that standards for radiation protection are adhered to. In addition, a survey of current radiological health practices is summarized

Radiological health aspects of uranium milling

Energy Technology Data Exchange (ETDEWEB)

Fisher, D.R.; Stoetzel, G.A.

1983-05-01

This report describes the operation of conventional and unconventional uranium milling processes, the potential for occupational exposure to ionizing radiation at the mill, methods for radiological safety, methods of evaluating occupational radiation exposures, and current government regulations for protecting workers and ensuring that standards for radiation protection are adhered to. In addition, a survey of current radiological health practices is summarized.

Preparation of iron sulphides by high energy ball milling

DEFF Research Database (Denmark)

Lin, R.; Jiang, Jianzhong; Larsen, R.K.

1998-01-01

The reaction of a powder mixture consisting of 50 a.% Fe and 50 a.% S during high energy ball milling has been studied by x-ray diffraction and Mossbauer spectroscopy. After around 19 h of milling FeS2 and FeS havebeen formed. By further milling the FeS compound becomes dominating and only Fe......S with an average crystallite size of about 10 nm was observed after milling times longer than 67 h. Mossbauer spectra obtained with applied fields show that the particles are antiferromagnetic or have a strongly canted spin structure....

The Influence of Milling on the Dissolution Performance of Simvastatin

Directory of Open Access Journals (Sweden)

Thomas Rades

2010-12-01

Full Text Available Particle size reduction is a simple means to enhance the dissolution rate of poorly water soluble BCS-class II and IV drugs. However, the major drawback of this process is the possible introduction of process induced disorder. Drugs with different molecular arrangements may exhibit altered properties such as solubility and dissolution rate and, therefore, process induced solid state modifications need to be monitored. The aim of this study was two-fold: firstly, to investigate the dissolution rates of milled and unmilled simvastatin; and secondly, to screen for the main milling factors, as well as factor interactions in a dry ball milling process using simvastatin as model drug, and to optimize the milling procedure with regard to the opposing responses particle size and process induced disorder by application of a central composite face centered design. Particle size was assessed by scanning electron microscopy (SEM and image analysis. Process induced disorder was determined by partial least squares (PLS regression modeling of respective X-ray powder diffractograms (XRPD and Raman spectra. Valid and significant quadratic models were built. The investigated milling factors were milling frequency, milling time and ball quantity at a set drug load, out of which milling frequency was found to be the most important factor for particle size as well as process induced disorder. Milling frequency and milling time exhibited an interaction effect on the responses. The optimum milling settings using the maximum number of milling balls (60 balls with 4 mm diameter was determined to be at a milling frequency of 21 Hz and a milling time of 36 min with a resulting primary particle size of 1.4 μm and a process induced disorder of 6.1% (assessed by Raman spectroscopy and 8.4% (assessed by XRPD, at a set optimization limit of < 2 μm for particle size and < 10% for process induced disorder. This optimum was tested experimentally and the process induced disorder

7 CFR 58.419 - Curd mill and miscellaneous equipment.

Science.gov (United States)

2010-01-01

... 7 Agriculture 3 2010-01-01 2010-01-01 false Curd mill and miscellaneous equipment. 58.419 Section... Service 1 Equipment and Utensils § 58.419 Curd mill and miscellaneous equipment. Knives, hand rakes... of the curd mill should be of stainless steel. All pieces of equipment shall be so constructed that...

Development of an electromechanical principle for wet and dry milling

Science.gov (United States)

Halbedel, Bernd; Kazak, Oleg

2018-05-01

The paper presents a novel electromechanical principle for wet and dry milling of different materials, in which the milling beads are moved under a time- and local-variable magnetic field. A possibility to optimize the milling process in such a milling machine by simulation of the vector gradient distribution of the electromagnetic field in the process room is presented. The mathematical model and simulation methods based on standard software packages are worked out. The results of numerical simulations and experimental measurements of the electromagnetic field in the working chamber of a developed and manufactured laboratory plant correlate well with each other. Using the obtained operating parameters, dry milling experiments with crushed cement clinker and wet milling experiments of organic agents in the laboratory plant are performed and the results are discussed here.

Activity of Plodia interpunctella (Lepidoptera: Pyralidae) in and around flour mills.

Science.gov (United States)

Doud, C W; Phillips, T W

2000-12-01

Studies were conducted at two flour mills where male Indian meal moths, Plodia interpunctella (Hübner), were captured using pheromone-baited traps. Objectives were to determine the distribution of male P. interpunctella at different locations in and around the mills throughout the season, and to monitor moth activity before and after one of the mills was fumigated with methyl bromide to assess efficacy of treatment. Commercially available sticky traps baited with the P. interpunctella sex pheromone were placed at various locations outside and within the larger of the two mills (mill 1). Moths were captured inside mill 1 after methyl bromide fumigations. The highest numbers of P. interpunctella were caught outside the facility and at ground floor locations near outside openings. Additional traps placed in the rooms above the concrete stored-wheat silos at mill 1 during the second year captured more moths than did traps within the mill's production and warehouse areas. In another study, moths were trapped at various distances from a smaller flour mill (mill 2) to determine the distribution of moths outdoors relative to the mill. There was a negative correlation between moth capture and distance from the facility, which suggested that moth activity was concentrated at or near the flour mill. The effectiveness of the methyl bromide fumigations in suppressing moth populations could not be assessed with certainty because moths captured after fumigation may have immigrated from outside through opened loading bay warehouse doors. This study documents high levels of P. interpunctella outdoors relative to those recorded inside a food processing facility. Potential for immigration of P. interpunctella into flour mills and other stored product facilities from other sources may be greater than previously recognized. Moth entry into a food processing facility after fumigation is a problem that should be addressed by pest managers.

33 CFR 117.225 - Yellow Mill Channel.

Science.gov (United States)

2010-07-01

... 33 Navigation and Navigable Waters 1 2010-07-01 2010-07-01 false Yellow Mill Channel. 117.225 Section 117.225 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY BRIDGES DRAWBRIDGE OPERATION REGULATIONS Specific Requirements Connecticut § 117.225 Yellow Mill Channel. The...

Coal Moisture Estimation in Power Plant Mills

DEFF Research Database (Denmark)

Andersen, Palle; Bendtsen, Jan Dimon; Pedersen, Tom S.

2009-01-01

Knowledge of moisture content in raw coal feed to a power plant coal mill is of importance for efficient operation of the mill. The moisture is commonly measured approximately once a day using offline chemical analysis methods; however, it would be advantageous for the dynamic operation...... of the plant if an on-line estimate were available. In this paper we such propose an on-line estimator (an extended Kalman filter) that uses only existing measurements. The scheme is tested on actual coal mill data collected during a one-month operating period, and it is found that the daily measured moisture...

46 CFR 50.25-5 - Products requiring manufacturer or mill certification.

Science.gov (United States)

2010-10-01

... 46 Shipping 2 2010-10-01 2010-10-01 false Products requiring manufacturer or mill certification... manufacturer or mill certification. (a) Products required to be certified by a manufacturer or by mill... accepted without referring to its manufacturer or mill certification, if: (1) The product is marked in...

FePt magnetic particles prepared by surfactant-assisted ball milling

Energy Technology Data Exchange (ETDEWEB)

Velasco, V., E-mail: vvjimeno@fis.ucm.es [Instituto de Magnetismo Aplicado, UCM-ADIF-CSIC, P.O. Box 155, Las Rozas 28230 (Spain); Departamento de Física de Materiales, Universidad Complutense de Madrid, Madrid 28040 (Spain); Hernando, A.; Crespo, P. [Instituto de Magnetismo Aplicado, UCM-ADIF-CSIC, P.O. Box 155, Las Rozas 28230 (Spain); Departamento de Física de Materiales, Universidad Complutense de Madrid, Madrid 28040 (Spain)

2013-10-15

High-energy ball milling of Fe and Pt elemental powders has been carried out under dry and wet (in presence of solvent and surfactants) conditions. Dry milling leads to the formation of the disordered FCC-FePt alloy whereas by the wet milling procedure the main process is the decrease of Fe and Pt particle size, although some dissolution of Pt into Fe grains cannot be ruled out, and no hint of the formation of the FCC-FePt phase is observed even to milling times up to 20 h, as X-ray diffraction, electron microscopy and Mössbauer spectroscopy indicates. The as-milled particles were annealed at 600 °C for 2 h under Ar atmosphere. It is noticed that the disordered fcc-FePt phase observed in particles milled under dry conditions transform to ordered fct phase characterized by a hard magnetic behavior with a coercive field up to 10,000 Oe. However, those particles milled in the surfactant/solvent medium exhibit a soft magnetic behavior with a coercive field of 600 Oe. These results indicate that wet high-energy ball milling is not an adequate technique for obtaining single-phase FePt particles. - Highlights: • FePt particles have been obtained by high-energy ball milling. • In the presence of surfactants and solvents, almost no alloying process takes place. • After annealing, the coercive field of the FePt alloy particles increases from 150 Oe to 10,000 Oe.

Mineralogy and geochemistry of uranium mill tailings

International Nuclear Information System (INIS)

Pagel, M.; Somot, S.

2002-01-01

We have investigated three main types of uranium mill tailings: (1) acid mill tailings (Mounana, Gabon), (2) neutralized acid mill tailings (Ecarpiere and Jouac, France) and (3) alkaline mill tailings (Lodeve, France). We have focused especially on radium behaviour which is of major environmental concern in these tailings, but other metals were also studied. It is shown that in type 1 , trapping of 226 Ra by anglesite and barite is dominant whereas in types 2 and 3, 226 Ra is mainly or significantly scavenged by Fe- Mn oxyhydroxides. This study points out the importance of keeping conditions in which these oxyhydroxides will be stable for the long-term. Uranium would be also released during acidification of the tailings. This shows the importance to know more about the behavior of Ra during the crystallization of oxyhydroxides and during tailings diagenesis. Therefore, it is very important to study the sorption of Ra by clay minerals or late authigeneous minerals such as barite. (author)

75 FR 30844 - General Mills, Inc.; Withdrawal of Food Additive Petition

Science.gov (United States)

2010-06-02

...] (formerly Docket No. 2007F-0454) General Mills, Inc.; Withdrawal of Food Additive Petition AGENCY: Food and... 7M4770) had been filed by General Mills, Inc., One General Mills Blvd., Minneapolis, MN 55426. The... use in food production. General Mills, Inc., has now withdrawn the petition without prejudice to a...

Nano-sized crystalline drug production by milling technology.

Science.gov (United States)

Moribe, Kunikazu; Ueda, Keisuke; Limwikrant, Waree; Higashi, Kenjirou; Yamamoto, Keiji

2013-01-01

Nano-formulation of poorly water-soluble drugs has been developed to enhance drug dissolution. In this review, we introduce nano-milling technology described in recently published papers. Factors affecting the size of drug crystals are compared based on the preparation methods and drug and excipient types. A top-down approach using the comminution process is a method conventionally used to prepare crystalline drug nanoparticles. Wet milling using media is well studied and several wet-milled drug formulations are now on the market. Several trials on drug nanosuspension preparation using different apparatuses, materials, and conditions have been reported. Wet milling using a high-pressure homogenizer is another alternative to preparing production-scale drug nanosuspensions. Dry milling is a simple method of preparing a solid-state drug nano-formulation. The effect of size on the dissolution of a drug from nanoparticles is an area of fundamental research, but it is sometimes incorrectly evaluated. Here, we discuss evaluation procedures and the associated problems. Lastly, the importance of quality control, process optimization, and physicochemical characterization are briefly discussed.

Machinability Evaluation in Hard Milling of AISI D2 Steel

OpenAIRE

Gaitonde, Vinayak Neelakanth; Karnik, Sulse Ramesh; Maciel, Caio Henrique Alves; Rubio, Juan Carlos Campos; Abrão, Alexandre Mendes

2016-01-01

Milling of hardened steel components provides considerable benefits in terms of reduced manufacturing cost and time compared to traditional machining. Temperature variation in milling is an important factor affecting the wear of cutting tools. The poor selection of milling parameters may cause excessive tool wear and increased work surface roughness. Hence, there is a need to study the machinability aspects during milling of hardened steel components. In the present work, influence of cutting...

Analytical Modelling Of Milling For Tool Design And Selection

International Nuclear Information System (INIS)

Fontaine, M.; Devillez, A.; Dudzinski, D.

2007-01-01

This paper presents an efficient analytical model which allows to simulate a large panel of milling operations. A geometrical description of common end mills and of their engagement in the workpiece material is proposed. The internal radius of the rounded part of the tool envelope is used to define the considered type of mill. The cutting edge position is described for a constant lead helix and for a constant local helix angle. A thermomechanical approach of oblique cutting is applied to predict forces acting on the tool and these results are compared with experimental data obtained from milling tests on a 42CrMo4 steel for three classical types of mills. The influence of some tool's geometrical parameters on predicted cutting forces is presented in order to propose optimisation criteria for design and selection of cutting tools

Higher derivative super Yang-Mills theories

International Nuclear Information System (INIS)

Bergshoeff, E.; Rakowski, M.; Sezgin, E.

1986-11-01

The most general higher derivative Yang-Mills actions of the type (F 2 +α2F 4 ) which are globally supersymmetric up to order α 2 in six and ten dimensional spacetimes are given. The F 4 -terms turn out to occur in the combination α 2 (tr F 4 - 1/4(tr F 2 ) 2 ), where the trace is over the Lorentz indices. This result agrees with the low energy limit of the open superstring in ten dimensions, where α is the string tension. Surprisingly, the transformation rules of the Yang-Mills multiplet receive order α 2 corrections even in the off-shell formulation. For the case of Abelian Yang-Mills group, the action is expressed in Born-Infeld form with a metric generically given by (1+α 2 F 2 +...). (author)

Effect of Milling Time on the Microstructure, Physical and Mechanical Properties of Al-Al2O3 Nanocomposite Synthesized by Ball Milling and Powder Metallurgy

Science.gov (United States)

Matori, Khamirul Amin; Ostovan, Farhad; Abdul Aziz, Sidek; Mamat, Md Shuhazlly

2017-01-01

The effect of milling time on the morphology, microstructure, physical and mechanical properties of pure Al-5 wt % Al2O3 (Al-5Al2O3) has been investigated. Al-5Al2O3 nanocomposites were fabricated using ball milling in a powder metallurgy route. The increase in the milling time resulted in the homogenous dispersion of 5 wt % Al2O3 nanoparticles, the reduction of particle clustering, and the reduction of distances between the composite particles. The significant grain refining during milling was revealed which showed as a reduction of particle size resulting from longer milling time. X-Ray diffraction (XRD) analysis of the nanocomposite powders also showed that designated ball milling contributes to the crystalline refining and accumulation of internal stress due to induced severe plastic deformation of the particles. It can be argued that these morphological and microstructural variations of nanocomposite powders induced by designated ball milling time was found to contribute to an improvement in the density, densification, micro-hardness (HV), nano-hardness (HN), and Young’s modulus (E) of Al-5Al2O3 nanocomposites. HV, HN, and E values of nanocomposites were increased by ~48%, 46%, and 40%, after 12 h of milling, respectively. PMID:29072632

Effect of Milling Time on the Microstructure, Physical and Mechanical Properties of Al-Al2O3 Nanocomposite Synthesized by Ball Milling and Powder Metallurgy

Directory of Open Access Journals (Sweden)

Meysam Toozandehjani

2017-10-01

Full Text Available The effect of milling time on the morphology, microstructure, physical and mechanical properties of pure Al-5 wt % Al2O3 (Al-5Al2O3 has been investigated. Al-5Al2O3 nanocomposites were fabricated using ball milling in a powder metallurgy route. The increase in the milling time resulted in the homogenous dispersion of 5 wt % Al2O3 nanoparticles, the reduction of particle clustering, and the reduction of distances between the composite particles. The significant grain refining during milling was revealed which showed as a reduction of particle size resulting from longer milling time. X-Ray diffraction (XRD analysis of the nanocomposite powders also showed that designated ball milling contributes to the crystalline refining and accumulation of internal stress due to induced severe plastic deformation of the particles. It can be argued that these morphological and microstructural variations of nanocomposite powders induced by designated ball milling time was found to contribute to an improvement in the density, densification, micro-hardness (HV, nano-hardness (HN, and Young’s modulus (E of Al-5Al2O3 nanocomposites. HV, HN, and E values of nanocomposites were increased by ~48%, 46%, and 40%, after 12 h of milling, respectively.

33 CFR 117.800 - Mill Neck Creek.

Science.gov (United States)

2010-07-01

... 33 Navigation and Navigable Waters 1 2010-07-01 2010-07-01 false Mill Neck Creek. 117.800 Section 117.800 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY BRIDGES DRAWBRIDGE OPERATION REGULATIONS Specific Requirements New York § 117.800 Mill Neck Creek. The draw of the...

Agar agar-stabilized milled zerovalent iron particles for in situ groundwater remediation

Energy Technology Data Exchange (ETDEWEB)

Velimirovic, Milica; Schmid, Doris; Wagner, Stephan; Micić, Vesna; Kammer, Frank von der; Hofmann, Thilo, E-mail: thilo.hofmann@univie.ac.at

2016-09-01

Submicron-scale milled zerovalent iron (milled ZVI) particles produced by grinding macroscopic raw materials could provide a cost-effective alternative to nanoscale zerovalent iron (nZVI) particles for in situ degradation of chlorinated aliphatic hydrocarbons in groundwater. However, the aggregation and settling of bare milled ZVI particles from suspension presents a significant obstacle to their in situ application for groundwater remediation. In our investigations we reduced the rapid aggregation and settling rate of bare milled ZVI particles from suspension by stabilization with a “green” agar agar polymer. The transport potential of stabilized milled ZVI particle suspensions in a diverse array of natural heterogeneous porous media was evaluated in a series of well-controlled laboratory column experiments. The impact of agar agar on trichloroethene (TCE) removal by milled ZVI particles was assessed in laboratory-scale batch reactors. The use of agar agar significantly enhanced the transport of milled ZVI particles in all of the investigated porous media. Reactivity tests showed that the agar agar-stabilized milled ZVI particles were reactive towards TCE, but that their reactivity was an order of magnitude less than that of bare, non-stabilized milled ZVI particles. Our results suggest that milled ZVI particles could be used as an alternative to nZVI particles as their potential for emplacement into contaminated zone, their reactivity, and expected longevity are beneficial for in situ groundwater remediation. - Highlights: • Rapid aggregation and sedimentation were observed in bare milled ZVI particles. • Agar agar improved the stability of milled ZVI particle suspensions. • Agar agar enhanced the transport of milled ZVI particles in heterogeneous sands. • Agar agar reduced the reactivity of milled ZVI particles towards TCE.

Agar agar-stabilized milled zerovalent iron particles for in situ groundwater remediation

International Nuclear Information System (INIS)

Velimirovic, Milica; Schmid, Doris; Wagner, Stephan; Micić, Vesna; Kammer, Frank von der; Hofmann, Thilo

2016-01-01

Submicron-scale milled zerovalent iron (milled ZVI) particles produced by grinding macroscopic raw materials could provide a cost-effective alternative to nanoscale zerovalent iron (nZVI) particles for in situ degradation of chlorinated aliphatic hydrocarbons in groundwater. However, the aggregation and settling of bare milled ZVI particles from suspension presents a significant obstacle to their in situ application for groundwater remediation. In our investigations we reduced the rapid aggregation and settling rate of bare milled ZVI particles from suspension by stabilization with a “green” agar agar polymer. The transport potential of stabilized milled ZVI particle suspensions in a diverse array of natural heterogeneous porous media was evaluated in a series of well-controlled laboratory column experiments. The impact of agar agar on trichloroethene (TCE) removal by milled ZVI particles was assessed in laboratory-scale batch reactors. The use of agar agar significantly enhanced the transport of milled ZVI particles in all of the investigated porous media. Reactivity tests showed that the agar agar-stabilized milled ZVI particles were reactive towards TCE, but that their reactivity was an order of magnitude less than that of bare, non-stabilized milled ZVI particles. Our results suggest that milled ZVI particles could be used as an alternative to nZVI particles as their potential for emplacement into contaminated zone, their reactivity, and expected longevity are beneficial for in situ groundwater remediation. - Highlights: • Rapid aggregation and sedimentation were observed in bare milled ZVI particles. • Agar agar improved the stability of milled ZVI particle suspensions. • Agar agar enhanced the transport of milled ZVI particles in heterogeneous sands. • Agar agar reduced the reactivity of milled ZVI particles towards TCE.

Improved hydrogen sorption kinetics in wet ball milled Mg hydrides

Energy Technology Data Exchange (ETDEWEB)

Meng, Li

2011-05-04

In this work, wet ball milling method is used in order to improve hydrogen sorption behaviour due to its improved microstructure of solid hydrogen materials. Compared to traditional ball milling method, wet ball milling has benefits on improvement of MgH{sub 2} microstructure and further influences on its hydrogen sorption behavior. With the help of solvent tetrahydrofuran (THF), wet ball milled MgH{sub 2} powder has much smaller particle size and its specific surface area is 7 times as large as that of dry ball milled MgH{sub 2} powder. Although after ball milling the grain size is decreased a lot compared to as-received MgH{sub 2} powder, the grain size of wet ball milled MgH{sub 2} powder is larger than that of dry ball milled MgH{sub 2} powder due to the lubricant effect of solvent THF during wet ball milling. The improved particle size and specific surface area of wet ball milled MgH{sub 2} powder is found to be determining its hydrogen sorption kinetics especially at relatively low temperatures. And it also shows good cycling sorption behavior, which decides on its industrial applicability. With three different catalysts MgH{sub 2} powder shows improved hydrogen sorption behavior as well as the cyclic sorption behavior. Among them, the Nb{sub 2}O{sub 5} catalyst is found to be the most effective one in this work. Compared to the wet ball milled MgH{sub 2} powder, the particle size and specific surface area of the MgH{sub 2} powder with catalysts are similar to the previous ones, while the grain size of the MgH{sub 2} with catalysts is much finer. In this case, two reasons for hydrogen sorption improvement are suggested: one is the reduction of the grain size. The other may be as pointed out in some literatures that formation of new oxidation could enhance the hydrogen sorption kinetics, which is also the reason why its hydrogen capacity is decreased compared to without catalysts. After further ball milling, the specific surface area of wet ball milled Mg

Health physics program for the Edgemont Uranium Mill decommissioning project

International Nuclear Information System (INIS)

Polehn, J.L.; Wallace, R.G.; Reed, R.P.; Wilson, G.T.

1986-01-01

The Tennessee Valley Authority (TVA) is actively involved in decommissioning a uranium mill located near the town of Edgemont, South Dakota. The Edgemont Mill Decommissioning Project, which is unique in many respects, will involve dismantlement of the old inactive mill building and excavation and transportation of several million tons of uranium mill tailings to a permanent disposal site. To ensure that workers are adequately protected from radiation exposure during decommissioning operations, a health physics program appropriate for the decommissioning situation was developed. The Edgemont Mill Decommissioning Project Health Physics Manual (HPM) gives the programmatic requirements for worker radiation protection. The requirements of the HPM are implemented by means of detailed onsite operating procedures. The Edgemont project health physics program was developed using currently available regulations and guidance for an operating uranium mill with appropriate modifications for decommissioning. This paper discusses the development, implementation, and documentation of that program

Geochemical Characterization of Mine Waste, Mine Drainage, and Stream Sediments at the Pike Hill Copper Mine Superfund Site, Orange County, Vermont

Science.gov (United States)

Piatak, Nadine M.; Seal, Robert R.; Hammarstrom, Jane M.; Kiah, Richard G.; Deacon, Jeffrey R.; Adams, Monique; Anthony, Michael W.; Briggs, Paul H.; Jackson, John C.

2006-01-01

The Pike Hill Copper Mine Superfund Site in the Vermont copper belt consists of the abandoned Smith, Eureka, and Union mines, all of which exploited Besshi-type massive sulfide deposits. The site was listed on the U.S. Environmental Protection Agency (USEPA) National Priorities List in 2004 due to aquatic ecosystem impacts. This study was intended to be a precursor to a formal remedial investigation by the USEPA, and it focused on the characterization of mine waste, mine drainage, and stream sediments. A related study investigated the effects of the mine drainage on downstream surface waters. The potential for mine waste and drainage to have an adverse impact on aquatic ecosystems, on drinking- water supplies, and to human health was assessed on the basis of mineralogy, chemical concentrations, acid generation, and potential for metals to be leached from mine waste and soils. The results were compared to those from analyses of other Vermont copper belt Superfund sites, the Elizabeth Mine and Ely Copper Mine, to evaluate if the waste material at the Pike Hill Copper Mine was sufficiently similar to that of the other mine sites that USEPA can streamline the evaluation of remediation technologies. Mine-waste samples consisted of oxidized and unoxidized sulfidic ore and waste rock, and flotation-mill tailings. These samples contained as much as 16 weight percent sulfides that included chalcopyrite, pyrite, pyrrhotite, and sphalerite. During oxidation, sulfides weather and may release potentially toxic trace elements and may produce acid. In addition, soluble efflorescent sulfate salts were identified at the mines; during rain events, the dissolution of these salts contributes acid and metals to receiving waters. Mine waste contained concentrations of cadmium, copper, and iron that exceeded USEPA Preliminary Remediation Goals. The concentrations of selenium in mine waste were higher than the average composition of eastern United States soils. Most mine waste was

Infrared finiteness in Yang--Mills theories

International Nuclear Information System (INIS)

Appelquist, T.; Carazzone, J.; Kluberg-Stern, H.; Roth, M.

1976-01-01

The infrared divergences of renormalizable theories with coupled massless fields (in particular, the Yang--Mills theory) are shown to cancel for transition probabilities corresponding to finite-energy-resolution detectors, just as in quantum electrodynamics. This result is established through lowest nontrivial order in perturbation theory for the detection of massive muons in a quantum electrodynamic theory containing massless electrons or the detection of massive quarks in a Yang--Mills theory

Analysis of crystallite size and microdeformation crystal lattice the tungsten carbide milling in mill high energy

International Nuclear Information System (INIS)

Silva, F.T. da; Nunes, M.A.M.; Souza, C.P. de; Gomes, U.U.

2010-01-01

The tungsten carbide (WC) has wide application due to its properties like high melting point, high hardness, wear resistance, oxidation resistance and good electrical conductivity. The microstructural characteristics of the starting powders influences the final properties of the carbide. In this context, the use of nanoparticle powders is an efficient way to improve the final properties of the WC. The high energy milling stands out from other processes to obtain nanometric powders due to constant microstructural changes caused by this process. Therefore, the objective is to undertake an analysis of microstructural characteristics on the crystallite size and microdeformations of the crystal lattice using the technique of X-ray diffraction (XRD) using the Rietveld refinement. The results show an efficiency of the milling process to reduce the crystallite size, leading to a significant deformation in the crystal lattice of WC from 5h milling. (author)

Degree of Milling Effect on Cold Water Rice Quality

Directory of Open Access Journals (Sweden)

Ujjwol Subedi

2018-05-01

Full Text Available The aim of this study was to examine the effects of degree of milling on various rice parameters such as proximate composition, and cooking properties using mathematical model. The experiments were performed in the laboratory of Food Research Division, Nepal Agricultural Research Council. The three different medium type rice varieties of Nepal (Lumle-2, Chhomrong and Machhapuchre-3 were exposed to five different degrees of milling (0%, 6%, 8%, 10% and 12%. The degree of milling (DM level significantly (P≤0.05 affected the milling recovery; head rice yield, nutrient content as well as cooking properties of the rice. Increase in DM resulted in further reduction of protein content, fat content, minerals, milled rice and head rice yield after bran layer was further removed. A positive correlation between DM used in present model, amylose content, kernel elongation and gruel solid loss was observed, however, with an increase in DM; amylose content, kernel elongation and gruel solid loss were found to be increased. Adopting 6 to 8% DM for commercial milling of rice might help to prevent quantitative, qualitative and nutritional loss along with retention of good cooking characteristics.

The dispersion of fine chitosan particles by beads-milling

Science.gov (United States)

Rochima, Emma; Utami, Safira; Hamdani, Herman; Azhary, Sundoro Yoga; Praseptiangga, Danar; Joni, I. Made; Panatarani, Camellia

2018-02-01

This research aimed to produce fine chitosan particles from a crab shell waste by beads-milling method by two different concentration of PEG as dispersing agent (150 and 300 wt. %). The characterization was performed to obtain the size and size distribution, the characteristics of functional groups and the degree of deacetylation. The results showed that the chitosan fine particles was obtained with a milling time 120 minutes with the best concentration of PEG 400 150 wt. %. The average particle size of the as-prepared suspension is 584 nm after addition of acetic acid solution (1%, v/v). Beads milling process did not change the glucosamine and N-acetylglucosamine content on chitosan structure which is indicated by degree of deacetylation higher than 70%. It was concluded that beads milling process can be applied to prepare chitosan fineparticles by proper adjustment in the milling time, pH and dosage of dispersing agent.

Investigation of the milling-induced thermal behavior of crystalline and amorphous griseofulvin.

Science.gov (United States)

Trasi, Niraj S; Boerrigter, Stephan X M; Byrn, Stephen Robert

2010-07-01

To gain a better understanding of the physical state and the unusual thermal behavior of milled griseofulvin. Griseofulvin crystals and amorphous melt quench samples were milled in a vibrating ball mill for different times and then analyzed using differential scanning calorimetry (DSC) and powder X-ray diffraction (PXRD). Modulated DSC (mDSC) and annealing studies were done for the milled amorphous samples to further probe the effects of milling. Milling of griseofulvin crystals results in decrease in crystallinity and amorphization of the compound. A double peak is seen for crystallization in the DSC, which is also seen for the milled melt quench sample. Both enthalpy and temperature of crystallization decrease for the milled melt quenched sample. Tg is visible under the first peak with the mDSC, and annealing shows that increasing milling time results in faster crystallization upon storage. Milling of griseofulvin results in the formation of an amorphous form and not a mesophase. It increases the amount of surface created and the overall energy of the amorphous griseofulvin, which leads to a decreased temperature of crystallization. The two exotherms in the DSC are due to some particles having nuclei on the surface.

Partial amorphization of an α-FeCr alloy by ball-milling

International Nuclear Information System (INIS)

Loureiro, J. M.; Costa, B. F. O.; Caer, G. Le; Delcroix, P.

2008-01-01

The structural changes of near-equiatomic α-FeCr alloys, ground in a vibratory mill in vacuum and in argon, were followed as a function of milling time. An amorphous phase forms in both cases but at a much faster rate when milling in argon than when milling in vacuum. Amorphisation by ball-milling of α-FeCr alloys is deduced to be an intrinsic phenomenon which is however speeded-up by oxygen. The amorphous phase crystallizes into a bcc Cr-rich phase and a bcc Fe-rich phase when annealed for short times.

Effect of kernel size and mill type on protein, milling yield, and baking quality of hard red spring wheat

Science.gov (United States)

Optimization of flour yield and quality is important in the milling industry. The objective of this study was to determine the effect of kernel size and mill type on flour yield and end-use quality. A hard red spring wheat composite sample was segregated, based on kernel size, into large, medium, ...

Investigations on d.c. conductivity behaviour of milled carbon fibre ...

Indian Academy of Sciences (India)

This paper reports the d.c. conductivity behaviour of milled carbon fibre reinforced polysulphide modified epoxy gradient composites. Milled carbon fibre reinforced composites having 3 vol. % of milled carbon fibre and poly sulphide modified epoxy resin have been developed. D.C. conductivity measurements are conducted ...

21 CFR 515.11 - Supplemental medicated feed mill license applications.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Supplemental medicated feed mill license... SERVICES (CONTINUED) ANIMAL DRUGS, FEEDS, AND RELATED PRODUCTS MEDICATED FEED MILL LICENSE Applications § 515.11 Supplemental medicated feed mill license applications. (a) After approval of a medicated feed...

Parametric optimization of CNC end milling using entropy ...

African Journals Online (AJOL)

Parametric optimization of CNC end milling using entropy measurement technique combined with grey-Taguchi method. ... International Journal of Engineering, Science and Technology ... Keywords: CNC end milling, surface finish, material removal rate (MRR), entropy measurement technique, Taguchi method ...

Preparation of tungsten-iron carbide by ball milling

International Nuclear Information System (INIS)

Wang, G.M.; Campbell, S.J.; Calka, A.; Kaczmarek, W.A.

1996-01-01

Several sets of elemental powder mixtures of Fe-W-C (W 46 Fe 46 C 8 , W 60 Fe 20 C 20 and W 34 Fe 33 C 33 ) were ball milled using Uni-Ball mill for periods of up to 550 h in vacuum with a ball - to - powder ratio of about 35:1. Depending on the milling time, the main component of the as-milled materials was found to be solid solutions of Fe-W-C or Fe-C. Ternary phase W 3 Fe 3 C was obtained on annealing the as-milled materials at about 700 deg C. This product was then found to transfer to (FeW) 6 C on heat treatment at about 800 deg C. The resultant products of the annealing processes were found to depend not only on the annealing temperature, but also the starting composition, especially the initial carbon concentration. Detailed information on the structural and phase evolution during thermal treatment as measured using x-ray diffraction, Moessbauer spectroscopy and thermal analysis is presented. Special interest is focused on the competition for formation in this system between the Fe-C, W-Fe and W-C phases

CO2 laser milling of hard tissue

Science.gov (United States)

Werner, Martin; Ivanenko, Mikhail; Harbecke, Daniela; Klasing, Manfred; Steigerwald, Hendrik; Hering, Peter

2007-02-01

Drilling of bone and tooth tissue belongs to recurrent medical procedures (screw- and pin-bores, bores for implant inserting, trepanation etc.). Small round bores can be in general quickly produced with mechanical drills. Problems arise however by angled drilling, by the necessity to fulfill the drilling without damaging of sensitive soft tissue beneath the bone, or by the attempt to mill precisely noncircular small cavities. We present investigations on laser hard tissue "milling", which can be advantageous for solving these problems. The "milling" is done with a CO2 laser (10.6 μm) with pulse duration of 50 - 100 μs, combined with a PC-controlled galvanic beam scanner and with a fine water-spray, which helps to avoid thermal side-effects. The damaging of underlying soft tissue can be prevented through control of the optical or acoustical ablation signal. The ablation of hard tissue is accompanied with a strong glowing, which is absent during the laser beam action on soft tissue. The acoustic signals from the diverse tissue types exhibit distinct differences in the spectral composition. Also computer image analysis could be a useful tool to control the operation. Laser "milling" of noncircular cavities with 1 - 4 mm width and about 10 mm depth is particularly interesting for dental implantology. In ex-vivo investigations we found conditions for fast laser "milling" of the cavities without thermal damage and with minimal tapering. It included exploration of different filling patterns (concentric rings, crosshatch, parallel lines and their combinations), definition of maximal pulse duration, repetition rate and laser power, optimal position of the spray. The optimized results give evidences for the applicability of the CO2 laser for biologically tolerable "milling" of deep cavities in the hard tissue.

Machining NiTi micro-parts by micro-milling

International Nuclear Information System (INIS)

Weinert, K.; Petzoldt, V.

2008-01-01

The machinability of NiTi by milling has been examined using solid carbide end milling cutters. First results were obtained from machining simple slots applying TiAlN-coated tools with a diameter of 0.4 mm. The machining process was evaluated in terms of tool wear, cutting forces and machining quality. The tool wear and work piece quality was analysed with a scanning electron microscope and a white-light confocal microscope. Despite the poor machinability of NiTi good results concerning tool wear and shape accuracy of the milled slots were achieved. Essential for a good machining result is the application of minimum quantity lubrication. This clearly reduces NiTi adherences compared to dry machining. Work piece quality is improved and tool life is extended. Based on these results different structures could be produced by micro-milling

Towards the effective tool wear control in micro-EDM milling

DEFF Research Database (Denmark)

Bissacco, Giuliano; Valentincic, J.; Hansen, Hans Nørgaard

2010-01-01

The electrode wear in micro-electrical discharge milling (micro-EDM milling) is one of the main problems to be solved in order to improve machining accuracy. This paper presents an investigation on wear and material removal in micro-EDM milling for selected process parameter combinations typical...... of the accuracy of volume measurements on the electrode wear per discharge and on the material removal per discharge are discussed, and the issues limiting the applicability of real time wear sensing in micro-EDM milling are presented....

Case history: Vertical barrier wall system for Superfund Site

International Nuclear Information System (INIS)

Koelling, M.A.; Kovac, C.P.; Norris, J.E.

1997-01-01

Design considerations and construction aspects are presented for the installation of a vertical barrier wall system for the Boeing Company at a Superfund Site near Seattle, WA. The construction was performed during 1996. The vertical barrier wall system included: (1) a soil-bentonite (SB) slurry wall, approximately 670 meters (2200 feet) in length, ranging from 12 to 21 meters (40 to 70 feet) in depth; (2) expansion of a cover system over the area enclosed by the SB wall; and (3) surface drainage improvements. Design and construction of the system addressed requirements of a Consent Decree for the site issued in 1993. The paper discusses the development of the design to meet remedial performance goals of preventing migration of contaminants in the soil/groundwater system and aiding aquifer restoration. Secondly, the paper details installation of the SB wall, highlighting the more significant construction issues, which included excavation of the wall through glacially deposited cobbles/boulders/till as well as addressing the severe elevation changes along the wall alignment. Thirdly, the paper presents Quality Assurance (QA) monitoring and testing performed during the construction phase

Massive Yang-Mills fields in the Kemmer's formulation

International Nuclear Information System (INIS)

Santana Cordolino, L.A. de.

1984-01-01

The Kemmer's equation, which describes the meson, is presented in the field theory formalism. Conservated, quantities are found through the Noether's identity. This formalism is used for masive Yang-Mills fields and two equations, similar to the Kemmer's equation, are obtained, although of different formates, both containing quadratic terms. In consequence two Lagrangians are defined, formally distint, for the Yang-Mills fields. The Schroedinger-like Hamiltonian is calculated for the first wave equations. This Hamiltonian presentes one spin-Yang-Mills field interaction term, PHI jk . (L.C.) [pt

Tungsten-nanodiamond composite powders produced by ball milling

Energy Technology Data Exchange (ETDEWEB)

Nunes, D., E-mail: daniela.nunes@ist.utl.pt [Associacao Euratom/IST, Instituto de Plasmas e Fusao Nuclear, Instituto Superior Tecnico, Universidade Tecnica de Lisboa, Av. Rovisco Pais, 1049-001 Lisboa (Portugal); LNEG, Estrada do Paco do Lumiar, 1649-038 Lisboa (Portugal); ICEMS, Instituto Superior Tecnico, Av. Rovisco Pais, 1049-001 Lisboa (Portugal); Livramento, V. [Associacao Euratom/IST, Instituto de Plasmas e Fusao Nuclear, Instituto Superior Tecnico, Universidade Tecnica de Lisboa, Av. Rovisco Pais, 1049-001 Lisboa (Portugal); LNEG, Estrada do Paco do Lumiar, 1649-038 Lisboa (Portugal); Mardolcar, U.V. [Departamento de Fisica, Instituto Superior Tecnico, Av. Rovisco Pais, 1049-001 Lisboa (Portugal); Centro de Ciencias Moleculares e Materiais, Faculdade de Ciencias da Universidade de Lisboa, Campo Grande, 1749-016 Lisboa (Portugal); Correia, J.B. [LNEG, Estrada do Paco do Lumiar, 1649-038 Lisboa (Portugal); Carvalho, P.A. [ICEMS, Instituto Superior Tecnico, Av. Rovisco Pais, 1049-001 Lisboa (Portugal); Departamento de Bioengenharia, Instituto Superior Tecnico, Av. Rovisco Pais, 1049-001 Lisboa (Portugal)

2012-07-15

The major challenge in producing tungsten-nanodiamond composites by ball milling lies in successfully dispersing carbon nanoparticles in the metallic matrix while keeping carbide formation at a minimum. Processing windows for carbide minimization have been established through systematic variation of the nanodiamond fraction, milling energy and milling time. Materials characterization has been carried out by X-ray diffraction, scanning and transmission electron microscopy and microhardness testing. Nanostructured matrices with homogeneously dispersed particles that preserved the diamond structure have been produced. Differential thermal analysis has been used to evaluate the composites thermal stability.

Ferromagnetic behavior of nanocrystalline Cu–Mn alloy prepared by ball milling

Energy Technology Data Exchange (ETDEWEB)

Mondal, B.N., E-mail: bholanath_mondal@yahoo.co.in [Department of Central Scientific Services, Indian Association for the Cultivation of Science, Jadavpur, Kolkata 700 032 (India); Sardar, G. [Department of Zoology, Baruipur College, South 24 parganas 743 610 (India); Nath, D.N. [Department of Physical Chemistry, Indian Association for the Cultivation of Science, Jadavpur, Kolkata 700 032 (India); Chattopadhyay, P.P. [Department of Metallurgy and Materials Engineering, Bengal Engineering and Science University, Shibpur, Howrah 711 103 (India)

2014-12-15

50Cu–50Mn (wt%) alloy was produced by ball milling. The milling was continued up to 30 h followed by isothermal annealing over a four interval of temperature from 350 to 650 °C held for 1 h. Crystallite size, lattice strain, lattice parameter were determined by Rietveld refinement structure analysis of X-ray diffraction data. The amount of dissolved/precipitated Mn (wt%) after ball milling/milling followed by annealing was calculated by quantative phase analysis (QPA). The increase of coercivity could be attributed to the introduction of lattice strain and reduction of crystallite size as a function of milling time. Electron paramagnetic resonance and superconducting quantum interface device analysis indicate that soft ferromagnetic behavior has been achieved by ball milled and annealed Cu–Mn alloy. The maximum coercivity value of Cu–Mn alloy obtained after annealing at 350 °C for 1 h is 277 Oe. - Highlights: • A small amount of Mn has dissolved in Cu after ball milling for 30 h. • Coercivity of the Cu–Mn alloy has increased with an increase in milling time. • Substantial MnO has formed after annealing at 650 °C for 1 h. • The ball milled and annealed alloy have revealed soft ferromagnetic behavior. • The alloy annealed at 350 °C shows the maximum value of coercivity.

Integrated chemical plants at the pulp mill

Energy Technology Data Exchange (ETDEWEB)

Ehtonen, P.; Hurme, M.; Jaervelaeinen, M.

1995-12-31

The goal of this paper is to present how the chemical plants can be integrated to the pulp mill. The integration renders possible to balance the chemical consumptions. The total mass balance of a pulp mill with the incoming fuel material and the outgoing waste and flue gases are discussed. The balance figures are presented for the chemicals of the modern fibre line, which will produce fully bleached softwood pulp with an improved effluent quality. The main benefits are lower chemical and transportation costs. The principal over-all plant process block diagrams and process descriptions are presented. The presented info system provides real time information on process and production status at overall mill and department levels. (author)

Structural and magnetic properties of ball milled copper ferrite

DEFF Research Database (Denmark)

Goya, G.F.; Rechenberg, H.R.; Jiang, Jianzhong

1998-01-01

The structural and magnetic evolution in copper ferrite (CuFe2O4) caused by high-energy ball milling are investigated by x-ray diffraction, Mössbauer spectroscopy, and magnetization measurements. Initially, the milling process reduces the average grain size of CuFe2O4 to about 6 nm and induces....... The canted spin configuration is also suggested by the observed reduction in magnetization of particles in the blocked state. Upon increasing the milling time, nanometer-sized CuFe2O4 particles decompose, forming alpha-Fe2O3 and other phases, causing a further decrease of magnetization. After a milling time...... of 98 h, alpha-Fe2O3 is reduced to Fe3O4, and magnetization increases accordingly to the higher saturation magnetization value of magnetite. Three sequential processes during high-energy ball milling are established: (a) the synthesis of partially inverted CuFe2O4 particles with a noncollinear spin...

Parametric Study of End Milling Glass Fibre Reinforced Composites

International Nuclear Information System (INIS)

Azmi, Azwan I.; Lin, Richard J. T.; Bhattacharyya, Debes

2011-01-01

This paper discusses the application of Taguchi 'Design of Experiment' method to investigate the effects of end milling parameters on machinability characteristics of unidirectional E-glass fibre reinforced polymer (GFRP) composites. A series of milling experiments were conducted using tungsten carbide end milling cutters at various spindle speeds, feed rates and depths of cut. Taguchi analysis was carried out and the signal to noise (S/N) ratio with analysis of variance (ANOVA) was employed to analyse the effects of those parameters on GFRP machinability. Overall, the results of the current investigations present some desirable combinations of the machining parameters that can further enhance the end milling machinability characteristics to suit the final requirements of the finished GFRP products.

Uranium mill tailings and radon

International Nuclear Information System (INIS)

Hanchey, L.A.

1981-01-01

The major health hazard from uranium mill tailings is presumed to be respiratory cancer resulting from the inhalation of radon daughter products. A review of studies on inhalation of radon and its daughters indicates that the hazard from the tailings is extremely small. If the assumptions used in the studies are correct, one or two people per year in the US may develop cancer as a result of radon exhaled from all the Uranium Mill Tailings Remedial Action Program sites. The remedial action should reduce the hazard from the tailings by a factor of about 100

Uranium mill tailings and radon

Energy Technology Data Exchange (ETDEWEB)

Hanchey, L A

1981-04-01

The major health hazard from uranium mill tailings is presumed to be respiratory cancer resulting from the inhalation of radon daughter products. A review of studies on inhalation of radon and its daughters indicates that the hazard from the tailings is extremely small. If the assumptions used in the studies are correct, one or two people per year in the United States may develop cancer as a result of radon exhaled from all the Uranium Mill Tailings Remedial Action program sites. The remedial action should reduce the hazard from the tailings by a factor of about 100.

Uranium mill tailings and radon

Energy Technology Data Exchange (ETDEWEB)

Hanchey, L A

1981-01-01

The major health hazard from uranium mill tailings is presumed to be respiratory cancer resulting from the inhalation of radon daughter products. A review of studies on inhalation of radon and its daughters indicates that the hazard from the tailings is extremely small. If the assumptions used in the studies are correct, one or two people per year in the US may develop cancer as a result of radon exhaled from all the Uranium Mill Tailings Remedial Action Program sites. The remedial action should reduce the hazard from the tailings by a factor of about 100.

Defect induced electronic states and magnetism in ball-milled graphite.

Science.gov (United States)

Milev, Adriyan; Dissanayake, D M A S; Kannangara, G S K; Kumarasinghe, A R

2013-10-14

The electronic structure and magnetism of nanocrystalline graphite prepared by ball milling of graphite in an inert atmosphere have been investigated using valence band spectroscopy (VB), core level near-edge X-ray absorption fine structure (NEXAFS) spectroscopy and magnetic measurements as a function of the milling time. The NEXAFS spectroscopy of graphite milled for 30 hours shows simultaneous evolution of new states at ~284.0 eV and at ~290.5 eV superimposed upon the characteristic transitions at 285.4 eV and 291.6 eV, respectively. The modulation of the density of states is explained by evolution of discontinuities within the sheets and along the fracture lines in the milled graphite. The magnetic measurements in the temperature interval 2-300-2 K at constant magnetic field strength show a correlation between magnetic properties and evolution of the new electronic states. With the reduction of the crystallite sizes of the graphite fragments, the milled material progressively changes its magnetic properties from diamagnetic to paramagnetic with contributions from both Pauli and Curie paramagnetism due to the evolution of new states at ~284 and ~290.5 eV, respectively. These results indicate that the magnetic behaviour of ball-milled graphite can be manipulated by changing the milling conditions.

Lupine protein enrichment by milling and electrostatic separation

NARCIS (Netherlands)

Wang, Jue; Zhao, Jun; Wit, De Martin; Boom, Remko M.; Schutyser, Maarten A.I.

2016-01-01

Lupine seeds are excellent source of plant protein. We here report on dry fractionation by combining milling and electrostatic separation providing an alternative to wet extraction of protein from lupine seeds. Relatively coarse milling was preferred as this provides sufficient detached protein

The influence of milling on the dissolution performance of simvastatin

DEFF Research Database (Denmark)

Zimper, Ulrike; Aaltonen, Jaakko; Krauel-Goellner, Karen

2012-01-01

properties such as solubility and dissolution rate and, therefore, process induced solid state modifications need to be monitored. The aim of this study was two-fold: firstly, to investigate the dissolution rates of milled and unmilled simvastatin; and secondly, to screen for the main milling factors......, as well as factor interactions in a dry ball milling process using simvastatin as model drug, and to optimize the milling procedure with regard to the opposing responses particle size and process induced disorder by application of a central composite face centered design. Particle size was assessed...... by scanning electron microscopy (SEM) and image analysis. Process induced disorder was determined by partial least squares (PLS) regression modeling of respective X-ray powder diffractograms (XRPD) and Raman spectra. Valid and significant quadratic models were built. The investigated milling factors were...

Crystallization degree change of expanded graphite by milling and annealing

International Nuclear Information System (INIS)

Tang Qunwei; Wu Jihuai; Sun Hui; Fang Shijun

2009-01-01

Expanded graphite was ball milled with a planetary mill in air atmosphere, and subsequently thermal annealed. The samples were characterized by using X-ray diffraction spectroscopy (XRD), scanning electron microscopy (SEM) and thermal gravimetric analysis (TGA). It was found that in the milling initial stage (less than 12 h), the crystallization degree of the expanded graphite declined gradually, but after milling more than 16 h, a recrystallization of the expanded graphite toke place, and ordered nanoscale expanded graphite was formed gradually. In the annealing initial stage, the non-crystallization of the graphite occurred, but, beyond an annealing time, recrystallizations of the graphite arise. Higher annealing temperature supported the recrystallization. The milled and annealed expanded graphite still preserved the crystalline structure as raw material and hold high thermal stability.

Cleaning up commingled uranium mill tailings: is Federal assistance necessary

International Nuclear Information System (INIS)

1979-01-01

GAO was asked to determine whether Federal assistance should be given to operating mill owners that have processed uranium for sale to both government and industry and, thus, generated residual radioactive wastes. The wastes generated for both government and commercial use are called commingled uranium mill tailings. GAO recommends that the Congress provide assistance to active mill owners to share in the cost of cleaning up that portion of the tailings which were produced under Federal contract. Further, GAO believes that the Congress should also consider having the Federal government assist those mills who acted in good faith in meeting all legal requirements pertaining to controlling the mill tailings that were generated for commercial purposes and for which the Federal government is now requiring retroactive remedial action. At the same time, the Congress should make sure that this action establishes no precedent for the Federal government assuming the financial responsibility of cleaning up other non-Federal nuclear facilities and wastes, including those mill tailings generated after the date when the Federal government notified industry that the failings should be controlled

Research on cutting vibration characteristics of face-milling involute gear

Directory of Open Access Journals (Sweden)

Chengzhe JIN

2017-10-01

Full Text Available Traditional machining methods, such as gear hobbing, gear shaping and gear milling, etc, are commonly used for cutting machining of gear tooth profile, which cannot meet huge machining demand of gears to a certain extent. This article proposes to utilize a face-milling machining method in involute gear machining, which can be used to reduce production cost effectively. Cutting vibration generated during cutting machining has a direct effect on the machining accuracy and machined surface quality of workpiece. Therefore, it is desiderated to perform in-depth research regarding this issue. ADAMS software was used to establish a rigid-flexible coupling virtual prototyping model of face-milling gear milling system and a cutting vibration system model. Cutting vibration analysis was performed for face-milling gear by adopting quick sine frequency sweep method, so that the frequency response characteristics of workpiece in three directions X, Y and Z and space were acquired. The research results will provide reference and theoretical foundation for actual application of face-milling gear machining technology.

Children's Rights, "die Antipadagogen," and the Paternalism of John Stuart Mill.

Science.gov (United States)

Nordenbo, Sven Erik

1989-01-01

Examines how John Stuart Mill would have viewed present-day educational liberalists' claims that children should be included in Mill's principle of individual liberty. Concludes that educational liberalists cannot rightly claim Mill as spokesman for their views. (KO)

Releases of radioactivity from uranium mills and effluent treatment costs

International Nuclear Information System (INIS)

Witherspoon, J.P.; Sears, M.B.; Blanco, R.E.

1977-01-01

Airborne releases of radioactive materials from uranium milling to the environment consist of ore dust, yellowcake dust, tailings dust, and radon gas while the mill is active. After a mill has ceased operations, tailings may be stabilized to minimize or prevent airborne releases of radioactive particulates. However, radon gas will continue to be released in amounts inversely proportional to the degree of stabilization treatment (and expense). Liquid waste disposal is by evaporation and natural seepage to the ground beneath the tailings impoundment area. The release of radioactive materials (and potential radiation exposures) determines the majority of costs associated with minimizing the environmental impact of uranium milling. Radwaste treatments to reduce estimated radiation doses to individuals to 3 to 5% of those received with current milling practices are equivalent to $0.66 per pounds of U 3 O 8 and 0.032 mill per kWhr of electricity. This cost would cover a high efficiency reverse jet bag filter and high energy venturi scrubbers for dusts, neutralization of liquids, and an asphalt-lined tailings basin with a clay core dam to reduce seepage. In addition, this increased cost would cover stabilization of tailings, after mill closure, with a 1-in. asphalt membrane topped by 2 ft of earth and 0.5 ft of crushed rock to provide protection against future leaching and wind erosion. The cost of reducing the radiological hazards associated with uranium milling to this degree would contribute about 0.4% to the current total cost of nuclear power

Chest radiological findings in pakistani cement mill workers

International Nuclear Information System (INIS)

Meo, Sultan A.

2003-01-01

Chest radiological findings in Pakistani cement mill workers Even in the 21st century, in developing countries millions of people work daily in dusty environments. They are exposed to different types of health hazards namely, fumes, gases and dust, which are risk factors for developing occupational diseases. Therefore, the aim of this study was to perform chest radiology to determine the occupational hazards of cement dust on the lungs of cement mill workers. This study was carried out in the Department of Physiology, Faculty of Health and Medical Sciences, Hamdard University Karachi, Pakistan, during the period June to August 2000. In this study 50, apparently healthy volunteer male cement mill workers were randomly selected with an average of 13 years exposure with age ranging from 20-60 years. They were matched with 50, healthy male control subjects in terms of age, height, weight and socioeconomic status. Both groups met with exclusion criteria as per standard. Radiology was performed by Trophy radiology. Results: The present study demonstrated 12% of cases with interstitial lung disease and 2% of cases with pleural thickening and chronic bronchitis in cement mill workers. Conclusion: Exposure to cement dust causes interstitial lung disease, pleural thickening and chronic bronchitis in cement mill workers. (author)

Superfund record of decision (EPA Region 2): Carroll and Dubies Sewage Disposal, Port Jervis, Town of Deerpark, Orange County, NY, September 30, 1996

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-01-01

This decision document presents the selected remedial action for the contaminated groundwater at the Carroll and Dubies Superfund Site (the Site). This operable unit represents the second of two operable units planned for the Site. It addresses the contaminated groundwater underlying and downgradient of the Carroll and Dubies site.

Gauged supersymmetries in Yang-Mills theory

International Nuclear Information System (INIS)

Tissier, Matthieu; Wschebor, Nicolas

2009-01-01

In this paper we show that Yang-Mills theory in the Curci-Ferrari-Delbourgo-Jarvis gauge admits some up to now unknown local linear Ward identities. These identities imply some nonrenormalization theorems with practical simplifications for perturbation theory. We show, in particular, that all renormalization factors can be extracted from two-point functions. The Ward identities are shown to be related to supergauge transformations in the superfield formalism for Yang-Mills theory. The case of nonzero Curci-Ferrari mass is also addressed.

Wastes from former mining and milling activities in Tajikistan

International Nuclear Information System (INIS)

Mirsaidov, U.M.

2012-01-01

This article is devoted to wastes from former mining and milling activities in Tajikistan. Currently, the serious radiological and ecological problems in Tajikistan are uranium mining and milling activities consequences overcoming which intensively developed during the soviet period. After the collapse of USSR, the uranic ores extraction in Tajikistan stopped due to deposit's output completion on the territory of the republic. Remediation of mining and milling activities' sites became the most urgent once all mines were closed.

The atmosphere as a source/sink of polychlorinated biphenyls to/from the Lower Duwamish Waterway Superfund site

International Nuclear Information System (INIS)

Apell, Jennifer N.; Gschwend, Philip M.

2017-01-01

Waterbodies polluted with polychlorinated biphenyls (PCBs) may cause the air in the surrounding area to become PCB-contaminated. Conversely, when a waterbody is located in or near an urban area, the deposition of atmospheric PCBs may act as a low-level, ongoing source of PCB contamination to that water. Distinguishing these situations is necessary to be protective of human populations and to guide efforts seeking to cleanup such aquatic ecosystems. To assess the situation at the Lower Duwamish Waterway (LDW) Superfund site, low-density polyethylene passive samplers were deployed in the summer of 2015 to quantify freely dissolved water and gaseous air concentrations of PCBs thereby enabling estimates of the direction and magnitude of air-water exchange of PCB congeners. For the sum of the 27 PCB congeners, average concentrations were 220 pg/m 3 (95% C.I.: 80–610) in the air and 320 pg/L (95% C.I.: 110–960) in the water. The sum of air-water exchange fluxes of these PCB congeners was estimated to be 68 ng/m 2 /day (95% C.I.: 30–148) into the lower atmosphere, contrasting with the reported wet and dry depositional flux of only 5.5 ng/m 2 /day (95% C.I.: 1–38) from the air into the water. Therefore, the atmosphere was ultimately a sink of PCBs from the LDW Superfund site, at least under 2015 summertime conditions. However, we conclude that air-water exchange of PCBs is likely only a minor sink of PCBs from the LDW and only a minor source of contamination to the region's local atmosphere. - Highlights: • Passive samplers were used to estimate air and water concentrations. • At this site, PCBs were being transported from the water into the local atmosphere. • Air-water exchange was likely only a minor sink of PCBs for the LDW site. • The LDW was likely only a minor source of PCBs to the local atmosphere. - Air-water exchange of PCBs from the LDW Superfund site, calculated using passive sampler data, was determined to be a minor sink of PCBs from

High-Energy Ball-Milling of Alloys and Compounds

International Nuclear Information System (INIS)

Le Caer, G.; Delcroix, P.; Begin-Colin, S.; Ziller, T.

2002-01-01

After outlining some characteristics of high-energy ball-milling, we discuss selected examples of phase transformation and of alloy synthesis which focus on deviations from archetypal behaviours and throw light on the milling mechanisms. Some contributions of Moessbauer spectrometry to the characterization of ground materials are described.

Visual Inspection for Breakage of Micro-milling Cutter

Directory of Open Access Journals (Sweden)

WANG Lei

2014-11-01

Full Text Available In order to realize visual inspection for breakage of micro-milling cutter, a developed image acquisition method of the surface of a micro-milling cutter was constructed and a classification method based on multilayer neural network was proposed in this article. While the milling cutter was rotating at a constant speed, a camera was triggered by a rotary encoder to capture a series of images. And the developed image of milling cutter was created by image mosaic algorithms. The moment of regional feature as well as the gray feature of the tooth edge was extracted as the input vector of neural network. The feature vector includes moment of inertia, geometric central moment, three-dimensional invariants moment and the gray value of the projection on two principal axis directions of the tooth region. By designing a proper neural network, breakage defects can be detected 100 %. And the false discovery rate is 0.5 %.

Descriptive documentation for New Mexico uranium milling model

International Nuclear Information System (INIS)

Bonem, G.; Livevano, R.J.

1981-01-01

The New Mexico Uranium Milling Model is a linear programming model. It can demonstrate how cost minimizing management can reduce the costs of milling uranium subject to a series of environmental, resource, and technological constraints. For example, if 15,000 tons were the targeted level of milling output, the model would provide the minimum cost of this production level, given certain levels of environmental, fuel, water, and technological constraints. The model was developed to allow state policymakers to assess the uranium industry from various standpoints. Through the use of the model, state policymakers can determine the effects of air and water discharge standards and limited capital availability on: milling costs of production; uses of electricity, fuel, and water; and levels of air and water emissions. The model covers the following: process technologies which are acid leach and carbonate leach; raw materials mix; air and water discharges; residual treatment process; and plant types

Superfund record of decision (EPA Region 2): Carroll and Dubies Sewage Disposal, Port Jervis, NY, March 31, 1995

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-08-01

This decision document presents the selected remedial action for the Carroll and Dubies Superfund Site (the Site). This operable unit (OU1) represents the first of two operable units planned for the Site. This operable unit addresses the source areas (lagoons and surrounding impacted soils) at the Site and actions needed to ensure that the source areas do not pose a threat to human health or the environment, including any potential cross media impacts to groundwater.

Conformally flat spaces and solutions to Yang-Mills equations

International Nuclear Information System (INIS)

Chaohao, G.

1980-01-01

Using the conformal invariance of Yang-Mills equations in four-dimensional manifolds, it is proved that in a simply connected space of negative constant curvature Yang-Mills equations admit solutions with any real number as their Pontryagin number. It is also shown that the space S 3 x S 1 which is the regular counterpart of the meron solution is one example of a class of solutions to Yang-Mills equations on compact manifolds that are neither self-dual nor anti-self-dual

Response to Thermal Exposure of Ball-Milled Aluminum-Borax Powder Blends

Science.gov (United States)

Birol, Yucel

2013-04-01

Aluminum-borax powder mixtures were ball milled and heated above 873 K (600 °C) to produce Al-B master alloys. Ball-milled powder blends reveal interpenetrating layers of deformed aluminum and borax grains that are increasingly refined with increasing milling time. Thermal exposure of the ball-milled powder blends facilitates a series of thermite reactions between these layers. Borax, dehydrated during heating, is reduced by Al, and B thus generated reacts with excess Al to produce AlB2 particles dispersed across the aluminum grains starting at 873 K (600 °C). AlB2 particles start to form along the interface of the aluminum and borax layers. Once nucleated, these particles grow readily to become hexagonal-shaped crystals that traverse the aluminum grains with increasing temperatures as evidenced by the increase in the size as well as in the number of the AlB2 particles. Ball milling for 1 hour suffices to achieve a thermite reaction between borax and aluminum. Ball milling further does not impact the response of the powder blend to thermal exposure. The nucleation-reaction sites are multiplied, however, with increasing milling time and thus insure a higher number of smaller AlB2 particles. The size of the AlB2 platelets may be adjusted with the ball milling time.

Occurences and Fate of DDT Principal Isomers/Metabolites, DDA, and o,p'-DDD Enantiomers in Fish, Sediment and Water at a DDT-Impacted Superfund Site

Science.gov (United States)

In the 1950s and 60s, discharges from a DDT manufacturing plant contaminated a tributary system of the Tennessee River near Huntsville, Alabama, USA. Regulatory action resulted in declaring the area a Superfund site which required remediation and extensive monitoring. Monitoring ...

Cosmological coevolution of Yang-Mills fields and perfect fluids

International Nuclear Information System (INIS)

Barrow, John D.; Jin, Yoshida; Maeda, Kei-ichi

2005-01-01

We study the coevolution of Yang-Mills fields and perfect fluids in Bianchi type I universes. We investigate numerically the evolution of the universe and the Yang-Mills fields during the radiation and dust eras of a universe that is almost isotropic. The Yang-Mills field undergoes small amplitude chaotic oscillations, as do the three expansion scale factors which are also displayed by the expansion scale factors of the universe. The results of the numerical simulations are interpreted analytically and compared with past studies of the cosmological evolution of magnetic fields in radiation and dust universes. We find that, whereas magnetic universes are strongly constrained by the microwave background anisotropy, Yang-Mills universes are principally constrained by primordial nucleosynthesis but the bound is comparatively weak with Ω YM rad

Integrated assessmet of the impacts associated with uranium mining and milling

Energy Technology Data Exchange (ETDEWEB)

Parzyck, D.C.; Baes, C.F. III; Berry, L.G.

1979-07-01

The occupational health and safety impacts are assessed for domestic underground mining, open pit mining, and milling. Public health impacts are calculated for a population of 53,000 located within 88 km (55 miles) of a typical southwestern uranium mill. The collective annual dose would be 6.5 man-lung rem/year, 89% of which is from /sup 222/Rn emitted from mill tailings. The dose to the United States population is estimated to be 6 x 10/sup 4/ man-lung rem from combined mining and milling operations. This may be comparedd with 5.7 x 10/sup 5/ man-lung rem from domestic use of natural gas and 4.4 x 10/sup 7/ man-lung rem from building interiors. Unavoidable adverse environmental impacts appear to be severe in a 250 ha area surrounding a mill site but negligible in the entire potentially impacted area (500,000 ha). The contemporary uranium resource and supply industry and its institutional settings are described in relation to the socio-economic impacts likely to emerge from high levels of uranium mining and milling. Radon and radon daughter monitoring techniques associated with uranium mining and milling are discussed.

Integrated assessmet of the impacts associated with uranium mining and milling

International Nuclear Information System (INIS)

Parzyck, D.C.; Baes, C.F. III; Berry, L.G.

1979-07-01

The occupational health and safety impacts are assessed for domestic underground mining, open pit mining, and milling. Public health impacts are calculated for a population of 53,000 located within 88 km (55 miles) of a typical southwestern uranium mill. The collective annual dose would be 6.5 man-lung rem/year, 89% of which is from 222 Rn emitted from mill tailings. The dose to the United States population is estimated to be 6 x 10 4 man-lung rem from combined mining and milling operations. This may be comparedd with 5.7 x 10 5 man-lung rem from domestic use of natural gas and 4.4 x 10 7 man-lung rem from building interiors. Unavoidable adverse environmental impacts appear to be severe in a 250 ha area surrounding a mill site but negligible in the entire potentially impacted area (500,000 ha). The contemporary uranium resource and supply industry and its institutional settings are described in relation to the socio-economic impacts likely to emerge from high levels of uranium mining and milling. Radon and radon daughter monitoring techniques associated with uranium mining and milling are discussed

A survey of present levels of radiocesium in Swedish pulp mill liquors and the implications for wood radiocesium transfer factors. Using Kraft mill liquors as an indicator of wood radiocesium contamination

International Nuclear Information System (INIS)

Ravila, A.; Holm, E.

2000-01-01

A survey was initiated to depict and compare the present activity levels in pulp mill liquors from various mill locations. The 137 Cs levels in pulp mill liquors were compared with the mill location and the deposition pattern of the Chernobyl fallout and nuclear weapons fallout. The large input of wood (about 2500 m 3 per day) to an average Nordic Kraft mill and the relatively long-term retention time for radiocesium in the Kraft mill recovery cycle enables representative sampling of substances directly related to the activity concentration in wood. (author)

Comprehensive Environmental Response, Compensation and Liability Act (CERCLA) or Superfund, Section 104(k); and CERCLA Section 104(d); ‘‘ ‘Discounted Loans’ Under Brownfields Revolving Loan Fund Grants’

Science.gov (United States)

Comprehensive Environmental Response, Compensation and Liability Act (CERCLA) or Superfund, Section 104(k); and CERCLA Section 104(d); ‘‘ ‘Discounted Loans’ Under Brownfields Revolving Loan Fund Grants’`

78 FR 38877 - Kraft Pulp Mills NSPS Review

Science.gov (United States)

2013-06-28

... ENVIRONMENTAL PROTECTION AGENCY 40 CFR Part 60 [EPA-HQ-OAR-2012-0640] FRL-9829-3 RIN 2060-AR64 Kraft Pulp Mills NSPS Review AGENCY: Environmental Protection Agency (EPA). ACTION: Proposed rule... comments on the May 23, 2013, proposed rule titled, ``Kraft Pulp Mills NSPS Review'' is being extended by...

Some global charges in classical Yang-Mills theory

International Nuclear Information System (INIS)

Chrus'ciel, P.T.; Kondracki, W.

1987-01-01

Three classes of boundary conditions allowing the definition of a global field strength (''global color'') are presented. A definition of global color of the sources and of the Yang-Mills field is proposed. Some exact solutions of Yang-Mills equations with point sources and with ''topologically nontrivial electric color'' are presented

Effects of milling on the extraction efficiency of incurred pesticides in cereals

DEFF Research Database (Denmark)

Herrmann, Susan Strange; Hajeb, Parvaneh; Andersen, Gitte

2017-01-01

This study investigated the effects of particle size and milling temperature on the extraction efficiencies of pesticide residues from cereal flour. Samples of cereal grains (barley, oat, rye and wheat) were milled using a centrifugal mill with four different sieves (0.2, 1.0, 3.0 and 5.0 mm......) or a knife mill both at room temperature and after freezing of the grain at –80°C overnight. The incurred pesticides in the test materials were extracted by the QuEChERS method and analysed by LC-MS/MS and GC-MS/MS. The particle size distribution for the milled samples was determined using a vibratory sieve...... shaker. Based on the pesticide levels recovered from each of the different millings and the corresponding particle size distributions, it was confirmed that smaller average particle sizes increase the extraction efficiency up to 31%, with all other factors equal. The cereals milled at room temperature...

76 FR 70170 - Proposed Alternative Soils Standards for the Uravan, Colorado Uranium Mill

Science.gov (United States)

2011-11-10

..., Colorado Uranium Mill AGENCY: Nuclear Regulatory Commission. ACTION: Uranium milling alternative standards... Agreements to regulate uranium mill tailings (11e.(2) byproduct material). Six Agreement States have this... in Colorado are acceptable. Discussion The Uravan site began operations in 1912 as a radium mill and...

Discrete element method based scale-up model for material synthesis using ball milling

Science.gov (United States)

Santhanam, Priya Radhi

Mechanical milling is a widely used technique for powder processing in various areas. In this work, a scale-up model for describing this ball milling process is developed. The thesis is a combination of experimental and modeling efforts. Initially, Discrete Element Model (DEM) is used to describe energy transfer from milling tools to the milled powder for shaker, planetary, and attritor mills. The rolling and static friction coefficients are determined experimentally. Computations predict a quasisteady rate of energy dissipation, E d, for each experimental configuration. It is proposed that the milling dose defined as a product of Ed and milling time, t, divided by the mass of milled powder, mp characterizes the milling progress independently of the milling device or milling conditions used. Once the milling dose is determined for one experimental configuration, it can be used to predict the milling time required to prepare the same material in any milling configuration, for which Ed is calculated. The concept is validated experimentally for DEM describing planetary and shaker mills. For attritor, the predicted Ed includes substantial contribution from milling tool interaction events with abnormally high forces (>103 N). The energy in such events is likely dissipated to heat or plastically deform milling tools rather than refine material. Indeed, DEM predictions for the attritor correlate with experiments when such events are ignored in the analysis. With an objective of obtaining real-time indicators of milling progress, power, torque, and rotation speed of the impeller of an attritor mill are measured during preparation of metal matrix composite powders in the subsequent portion of this thesis. Two material systems are selected and comparisons made between in-situ parameters and experimental milling progress indicators. It is established that real-time measurements can certainly be used to describe milling progress. However, they need to be interpreted carefully

21 CFR 515.20 - Approval of medicated feed mill license applications.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Approval of medicated feed mill license... SERVICES (CONTINUED) ANIMAL DRUGS, FEEDS, AND RELATED PRODUCTS MEDICATED FEED MILL LICENSE Administrative Actions on Licenses § 515.20 Approval of medicated feed mill license applications. Within 90 days after an...

21 CFR 515.23 - Voluntary revocation of medicated feed mill license.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Voluntary revocation of medicated feed mill... SERVICES (CONTINUED) ANIMAL DRUGS, FEEDS, AND RELATED PRODUCTS MEDICATED FEED MILL LICENSE Administrative Actions on Licenses § 515.23 Voluntary revocation of medicated feed mill license. A license issued under...

Superlocalization formulas and supersymmetric Yang-Mills theories

International Nuclear Information System (INIS)

Bruzzo, U.; Fucito, F.

2004-01-01

By using supermanifolds techniques we prove a generalization of the localization formula in equivariant cohomology which is suitable for studying supersymmetric Yang-Mills theories in terms of ADHM data. With these techniques one can compute the reduced partition functions of topological super-Yang-Mills theory with 4, 8 or 16 supercharges. More generally, the superlocalization formula can be applied to any topological field theory in any number of dimensions

Instability of higher dimensional Yang-Mills systems

International Nuclear Information System (INIS)

Randjbar-Daemi, S.; Strathdee, J.

1983-01-01

We investigate the stability of Poincare xO(3) invariant solutions for a pure semi-simple Yang-Mills, as well as Yang-Mills coupled to gravity in 6-dimensional space-time compactified over M 4 xS 2 . In contrast to the Maxwell U(1) theory (IC-82/208) in six dimensions coupled with gravity and investigated previously, the present theory exhibits tachyonic excitations and is unstable. (author)

Corporate Governance of Sugar Mills in East Java: A Transaction Cost Economics Perspective

Directory of Open Access Journals (Sweden)

Ahmad Erani Yustika

2007-01-01

Full Text Available Despite Indonesia’s overall achievements during the past two decades%2C the economy is encountering a series of problems. One of the biggest challenges is the unsatisfactory performance of the state-owned enterprises (SOEs. Subsidisies and uncovered loans to the SOEs have drained the government’s fiscal resources%2C and the signing off of employees creates many social problems. Compared with the SOEs in other sectors%2C state-owned sugar mills face more serious crises which not only jeopardise the social fabric%2C but also endanger the production. Research results strengthen the statement that the basic problem in sugar mills is management inefficiency resulting in high transaction costs. This research compares the transaction costs between state-owned (Ngadiredjo and privately-owned (Kebon Agung sugar mills. The study shows that in Kebon Agung Sugar Mill transaction costs are higher than production costs%2C while in Ngadiredjo Sugar Mill the reverse is true. However%2C the high transaction costs in Kebon Agung Sugar Mill cannot be attributed directly to inefficient institutions%2C because Ngadiredjo Sugar Mill incurred high costs for plants%2C land preparation%2C and fertilizer%2C which decreased the proportion of transaction costs. If analyzed in detail%2C the following facts are revealed: (i market transaction costs in Kebon Agung Sugar Mill are higher than in Ngadiredjo Sugar Mill. This is because Kebon Agung Sugar Mill has established cooperation with sugarcane farmers in the form of extensions and transport subsidies; and (ii the political transaction costs proportion in Ngadiredjo Sugar Mill is higher than in Kebon Agung Sugar Mill because of the imposition of many ‘illegal’ fees. Abstract in Bahasa Indonesia : transaction cost economics%2C corporate governance%2C sugar mill%2C East Java.

Pulp-mill related polychlorinated organic compounds in Baltic Sea sediments

Energy Technology Data Exchange (ETDEWEB)

Jonsson, Per (Swedish Environmental Protection Agency, Solna (Sweden)); Rappe, C.; Kjeller, L.O. (Umeaa Univ. (Sweden). Inst. of Environmental Chemistry); Kierkegaard, A. (Stockholm Univ. (Sweden). Inst. of Applied Environmental Research); Haakansson, L. (Uppsala Univ. (Sweden). Inst. of Earth Sciences); Jonsson, Bjoern (County Adm. Board, Umeaa (Sweden))

1993-01-01

Sediment samples from the Baltic basin were analyzed for PCDD/Fs, alkyl-CDFs, chloroguaiacols and EOCl. The EOCl distribution pattern in the Iggesund pulp-mill area shows high sediment concentrations close to the mill, and decreasing concentrations with increasing distance from the mill. Two series of alkyl-CDFs have been identified. The PCDD/Fs in offshore surficial sediments from the Baltic proper show a typical incineration pattern, while sediments collected in the vicinity of the mill show enhanced levels of 2,3,7,8-tetraCDD, 2,3,7,8- and 1,2,7,8-tetraCDF, and 1,2,3,7,8-pentaCDD. These PCDD/F congeners are statistically correlated to di-, tri-, and tetrachloroguaiacols, alkyl-CDFs, EOCl, and to the distance from the pulp mill, indicating the same source and transportation regime. Principal component analysis of the data set supports this conclusion. The three 2,3,7,8-tetrachloro-substituted PCDD/F congeners have formerly been found in high concentrations in sediments and crab hepatopancreas close to a pulp mill on the Swedish west coast. Our results from a pulp mill on the Swedish east coast support the conclusion that these congeners are typically associated with pulp bleaching. Deep layer sediments have significantly lower levels of PCDD/Fs. The isomer profiles are different in the surficial and the deep sediments, indicating a more natural preindustrial production of PCDD/Fs. (53 refs., 7 figs.).

Screening of plant species as ground cover on uranium mill tailings

International Nuclear Information System (INIS)

Venu Babu, P.; Eapen, S.

2012-01-01

The concept of construction of dams or holding areas for uranium mill tailings is relatively new in India and to date there is only one such facility being maintained by Uranium Corporation of India Limited (UCIL) at Jaduguda in Jharkhand. Due to the residual nature of radionuclides, chiefly uranium and its daughter products, special emphasis is given to the engineering aspects of the mill tailings ponds so as to ensure safety to general public for at least 200 years. Once a mill tailings pond reaches to its full capacity, creation of barrier layers over the mill tailings to prevent seepage of rain water and also erosion of mill tailings due to wind and water are advocated and a number of procedures are followed worldwide. Taking the extraordinary period of public safety to be assured, providing soil covers along with contouring and appropriate slopes over which vegetation is grown is gaining popularity. The vegetation not only reduces the impact of rain water hitting the soil cover, thereby reducing the soil erosion, but also lowers the moisture in the soil cover by extensive evapotranspiration, ensuring long term hydrological separation of the mill tailings underneath. Based on set criteria, applicable to the field scenario of mill tailings, a screening experiment was conducted under pot culture conditions to evaluate the survival and growth of different plant species. The plants after germination and hardening were transplanted into beakers containing mill tailings and periodical measurements on appropriate morphological characteristics such as plant height, length of twiners, number of tillers and number of leaves were recorded and evaluated. Of the twenty species tested in mill tailings, significant differences were noticed in the vigour of growth and several plant species could indeed establish well completing their life cycle including flowering and seed setting. Further, several leguminous species could also produce root nodules. It appears that the

Crook and overlength in hardwood lumber:results from a 14-mill survey

Science.gov (United States)

Jan Wiedenbeck; John Brown; Neal Bennett

2003-01-01

Data on red oak lumber were collected at 14 furniture and cabinet industry rough mills to identify how crook and overlength are related to lumber grade and size from mill to mill. The amount of crook in a sample of dry, 4/4 thickness, red oak lumber was significantly influenced by lumber grade and length, supply region, and mill. There were no differences in crook...

77 FR 35431 - Final Alternative Soils Standards for the Uravan, CO, Uranium Mill

Science.gov (United States)

2012-06-13

..., Uranium Mill AGENCY: Nuclear Regulatory Commission. ACTION: Notice of Uranium milling alternative... amend their agreements to regulate uranium mill tailings (11e.(2) byproduct material). Six Agreement... transferring the Uravan uranium mill site to the U.S. Department of Energy. The NRC staff found no deficiencies...

Nonperturbative Results for Yang-Mills Theories

DEFF Research Database (Denmark)

Sannino, Francesco; Schechter, Joseph

2010-01-01

Some non perturbative aspects of the pure SU(3) Yang-Mills theory are investigated assuming a specific form of the beta function, based on a recent modification by Ryttov and Sannino of the known one for supersymmetric gauge theories. The characteristic feature is a pole at a particular value....... Assuming the usual QCD value one finds it to be 1.67 GeV, which is in surprisingly good agreement with a quenched lattice calculation. A similar calculation is made for the supersymmetric Yang-Mills theory where the corresponding beta function is considered to be exact....

Automation for pilger mills at NZFP

International Nuclear Information System (INIS)

Manoher; Ramesh, K.; Rout, J.K.

1997-01-01

Pilgering is the critical operation in production of zircaloy fuel tubes. The in-going tube is required for feeding in pilgering and the outgoing pilger tube length is measured and is cut into required lengths and transferred to storage tank before sending for degreasing. The paper deals with the automation of the above operation carried out on the pilger mills of New Zircaloy Fabrication Plant (NZFP). This has helped in improving the quality of the pilgered tubes and productivity of the mill besides eliminating manual handling and cutting operations

Swedish Pulp Mill Biorefineries. A vision of future possibilities

Energy Technology Data Exchange (ETDEWEB)

Berntsson, Thore (Chamers Univ. of Technology, Goeteborg (Sweden)); Axegaard, Peter; Backlund, Birgit; Samuelsson, Aasa; Berglin, Niklas; Lindgren, Karin (STFI-Packforsk, Stockholm (Sweden))

2008-07-01

Today, modern science could make it possible to develop techniques for refining almost the whole wood-matter, pulp mill side streams and bark compounds into platform chemicals, electricity, high quality fuels and structured feed-stock for chemicals and materials. The major challenge is to convert the state of basic scientific knowledge into industrial practise. Our definition of an integrated biorefinery is: 'Full utilization of the incoming biomass and other raw materials for simultaneous and economically optimized production of fibres, chemicals and energy'. Examples of products from a pulp mill biorefinery are: Chemicals and Materials (Phenols, adhesives, carbon fibres, activated carbon, binders, barriers, adhesives, antioxidants, surfactants, chelants, solvents, adhesives surfactants, descaling agents, specialty polymers, pharmaceuticals, nutraceuticals, cosmetics etc., Biofuels (pellets, lignin fuel, methanol, DME, ethanol etc), Electricity (BLGCC, condensing power etc.). The new or increased amounts of traditional products can be made from internal and/or external biomass. Three different levels can be identified: A high degree of energy saving in future mills, especially chemical pulp mills, will lead to large amounts of excess internal biomass which can be transferred to products mentioned above, Components in e.g. the black liquor, forest residues and bark can be upgraded to more valuable ones and the energy balance of the mill is kept through fuel import, wholly or partly depending on the level of mill energy efficiency. This imported fuel can be biomass or other types. External (imported) biomass (in some cases together with excess internal biomass) can be upgraded using synergy effects of docking this upgrading to a pulp mill. Electricity has been included as one of the possible biorefinery products. The electricity production in a mill can be increased in several ways which cannot be directly considered as biorefineries, e.g. recovery boiler

Environmental control technology for mining, milling, and refining thorium

International Nuclear Information System (INIS)

Weakley, S.A.; Blahnik, D.E.; Young, J.K.; Bloomster, C.H.

1980-02-01

The purpose of this report is to evaluate, in terms of cost and effectiveness, the various environmental control technologies that would be used to control the radioactive wastes generated in the mining, milling, and refining of thorium from domestic resources. The technologies, in order to be considered for study, had to reduce the radioactivity in the waste streams to meet Atomic Energy Commission (10 CFR 20) standards for natural thorium's maximum permissible concentration (MPC) in air and water. Further regulatory standards or licensing requirements, either federal, state, or local, were not examined. The availability and cost of producing thorium from domestic resources is addressed in a companion volume. The objectives of this study were: (1) to identify the major waste streams generated during the mining, milling, and refining of reactor-grade thorium oxide from domestic resources; and (2) to determine the cost and levels of control of existing and advanced environmental control technologies for these waste streams. Six potential domestic deposits of thorium oxide, in addition to stockpiled thorium sludges, are discussed in this report. A summary of the location and characteristics of the potential domestic thorium resources and the mining, milling, and refining processes that will be needed to produce reactor-grade thorium oxide is presented in Section 2. The wastes from existing and potential domestic thorium oxide mines, mills, and refineries are identified in Section 3. Section 3 also presents the state-of-the-art technology and the costs associated with controlling the wastes from the mines, mills, and refineries. In Section 4, the available environmental control technologies for mines, mills, and refineries are assessed. Section 5 presents the cost and effectiveness estimates for the various environmental control technologies applicable to the mine, mill, and refinery for each domestic resource

Industrial recovered-materials-utilization targets for the textile-mill-products industry

Energy Technology Data Exchange (ETDEWEB)

None

1979-01-01

The Congress, in the National Energy Conservation and Policy Act of 1978 (NECPA), directed the Department of Energy to establish materials recovery targets for the metals and metal products, paper and allied products, rubber, and textile-mill-products industries. The targets were developed to provide incentives for using energy-saving recorded materials and to provied a yardstick for measuring progress and improvement in this endeavor. The NECPA indicates that the targets should represent the maximum technically and economically feasible increase in the use of energy-saving recovered materials that each industry can achieve progressively by January 1, 1987. Materials affected by recovered-materials targets include and are limited to aluminum, copper, lead, zinc, iron, steel, paper and associated products, textile-mill, products, and rubber. Using information gathered from the textile-mill-products industry and from other textile-relaed sources, DOE has developed recovered materials targets for that industry. This report presents those targets and their basis and justification. Following an overview of the textile industry, the chapters are: Textile-Mill-Products Industry Operations; Economic Analysis of the Textile-Mill-Products Industry; Governmental and Regulatory Influence on the US Textile Industry; Current Mill Use of Recovered Materials in the Textile-Mill-Products Industry; Limitations on the Use of Recovered Materials in the US Textile-Mill-Products Industry; Materials-Recovery Targets; and Government and Industry Actions That Could Increase the Use of Recovered Materials.

Aluminum-graphite composite produced by mechanical milling and hot extrusion

International Nuclear Information System (INIS)

Flores-Zamora, M.I.; Estrada-Guel, I.; Gonzalez-Hernandez, J.; Miki-Yoshida, M.; Martinez-Sanchez, R.

2007-01-01

Aluminum-graphite composites were produced by mechanical milling followed by hot extrusion. Graphite content was varied between 0 and 1 wt.%. Al-graphite mixtures were initially mixed in a shaker mill without ball, followed by mechanical milling in a High-energy simoloyer mill for 2 h under argon atmosphere. Milled powders were subsequently pressed at ∼950 MPa for 2 min, and next sintered under vacuum for 3 h at 823 K. Finally, sintered products were held for 0.5 h at 823 K and hot extruded using indirect extrusion. Tension and compression tests were carried out to determine the yield stress and maximum stress of the materials. We found that the mechanical resistance increased as the graphite content increased. Microstructural characterization was done by transmission electron microscopy. Al-O-C nanofibers and graphite nanoparticles were observed in extruded samples by transmission electron microscopy. These nanoparticles and nanofibers seemed to be responsible of the reinforcement phenomenon

Experimental Investigation on Ductile Mode Micro-Milling of ZrO2 Ceramics with Diamond-Coated End Mills

Directory of Open Access Journals (Sweden)

Rong Bian

2018-03-01

Full Text Available ZrO2 ceramics are currently used in a broad range of industrial applications. However, the machining of post-sintered ZrO2 ceramic is a difficult task, due to its high hardness and brittleness. In this study, micro-milling of ZrO2 with two kinds of diamond-coated end mills has been conducted on a Kern MMP 2522 micro-milling center (Kern Microtechnik GmbH, Eschenlohe, Germany. To achieve a ductile mode machining of ZrO2, the feed per tooth and depth of cut was set in the range of a few micrometers. Cutting force and machined surface roughness have been measured by a Kistler MiniDynamometer (Kistler Group, Winterthur, Switzerland and a Talysurf 120 L profilometer (Taylor Hobson Ltd., Leicester, UK, respectively. Machined surface topography and tool wear have been examined under SEM. Experiment results show that the material can be removed in ductile mode, and mirror quality surface with Ra low as 0.02 μm can be achieved. Curled and smooth chips have been collected and observed. The axial cutting force Fz is always bigger than Fx and Fy, and presents a rising trend with increasing of milling length. Tool wear includes delamination of diamond coating and wear of tungsten carbide substrate. Without the protection of diamond coating, the tungsten carbide substrate was worn out quickly, resulting a change of tool tip geometry.

Effect of milling time on the structure, particle size, and morphology of montmorillonite

International Nuclear Information System (INIS)

Abareshi, M.

2017-01-01

In the current research, effect of milling on the structure, particle size and morphology of montmorillonite was investigated. For this purpose, the montmorillonite was analyzed by X-ray diffraction, Fourier transform infrared spectroscopy, and scanning electron microscopy. Then the montmorillonite was milled using high energy planetary ball mill at different milling times (1-60 hours). After that, the structure, particle size and morphology of all samples were investigated by XRD, FTIR, SEM, and transmission electron microscopy. Results showed that the ball milling causes the particle size reduction of clay and separation of the clay layers. Moreover, ball milling increases the overall structural disorder and transforms the crystalline structure into an amorphous phase. Also, the morphology of clay particle changes from layered to aggregates of almost rounded particles after 60 hours of milling.

Milling properties of low temperature sintered zirconia blocks for dental use

Energy Technology Data Exchange (ETDEWEB)

Lan, Ting-Hsun; Wang, Chau-Hsiang [Department of Prosthodontics, Kaohsiung Medical University Hospital, Kaohsiung 80756, Taiwan (China); School of Dentistry, College of Dental Medicine, Kaohsiung Medical University, Kaohsiung 80728, Taiwan (China); Chen, Ker-Kong [Department of Conservation, Kaohsiung Medical University Hospital, Kaohsiung 80756, Taiwan (China); School of Dentistry, College of Dental Medicine, Kaohsiung Medical University, Kaohsiung 80728, Taiwan (China); Wang, Moo-Chin, E-mail: mcwang@kmu.edu.tw [Department of Fragrance and Cosmetic Science, Kaohsiung Medical University, 100 Shih-Chuan 1st Road, Kaohsiung 80728, Taiwan (China); Department of Medical Research, Kaohsiung Medical University Hospital, Kaohsiung, 80756, Taiwan (China); Lee, Huey-Er, E-mail: huerle@kmu.edu.tw [Department of Prosthodontics, Kaohsiung Medical University Hospital, Kaohsiung 80756, Taiwan (China); School of Dentistry, College of Dental Medicine, Kaohsiung Medical University, Kaohsiung 80728, Taiwan (China)

2017-04-01

To investigate the milling properties of different yttria-tetragonal zirconia polycrystalline (Y-TZP) block materials by applying a dental computer numerical control (CNC) milling center. Low temperature sintering zirconia block denoted by KMUZ (experimental) with two commercial zirconia blocks for T block made in Taiwan and a G block made in Germany were compared for the milling properties. Seventy-two specimens were milled using the same CNC milling center, and properties were evaluated by measuring the weight loss (g), milling time (s), margin integrity (%) and broken diameter (μm). The crystalline phases contents were identified by X-ray diffraction and the microstructures of the sintering specimens were observed by scanning electron microscopy and transmission electron microscopy. The mean milling time of G and KMUZ were significantly shorter than T (P < 0.05). The KMUZ samples exhibited the least weight loss among the three kinds of blocks (P < 0.05). The percentages of marginal integrity after milling were high in G and KMUZ but low in T (P < 0.05). The mean broken diameters were from 90 μm to 120 μm. The phase transformation of t-ZrO{sub 2} (KMUZ: 7.4%, G: 5.9%, T: 3.2%) to m-ZrO{sub 2} when facing the milling pressure in ZrO{sub 2} blocks was observed by XRD. The result of TEM microstructure of KMUZ revealed that Y and Si were soluble in grain boundaries. The results show that the milling properties of KMUZ were better than one commercial T and near the G. The hindered grain growth, as a result of the Y{sup 3+} content in the grain boundaries, also plays a role in promoting the abnormal grain growth of 3Y-TZP. - Highlights: • The phase transformation of t-ZrO{sub 2} to m-ZrO{sub 2} affects the milling properties. • The phase content of t-ZrO2 was 100% when sintering at 1350 °C for 2 h. • The Y{sup 3+} content in the grain boundaries that hinders grain growth. • The Y{sup 3+} content in boundaries also promotes the abnormal grain growth of 3Y-TZP.

Alloying and microstructural changes in platinum–titanium milled and annealed powders

International Nuclear Information System (INIS)

Maweja, Kasonde; Phasha, M.J.; Yamabe-Mitarai, Y.

2012-01-01

Graphical abstract: (a) SE-SEM micrographs of PtTi martensite formed in powder milled for short time annealed at 1500 °C and quenched in helium gas flow (b) BSE-SEM of structure formed after slow cooling. Highlights: ► A disordered metastable FCC Pt(Ti) solid solution was formed after longer milling period. ► HCP Ti crystals were first deformed and then the atoms were dissolved in strained FCC Pt lattices. ► Longer milling time suppressed the occurrence of martensitic transformation after annealing. ► Martensite phase was formed in products that went through a short milling time then annealed and quenched. ► The width of the martensite features formed was smaller at higher cooling rates. - Abstract: Equiatomic platinum–titanium powder mixtures were processed by high energy ball milling under argon atmosphere and sintered under vacuum. Evolution of the crystal structures and microstructures of the products formed were investigated by XRD and SEM techniques, respectively. The HCP crystals of Ti were first deformed and then a disordered metastable FCC Pt(Ti) solid solution was formed during milling due to semi-coherency of FCC lattices. A nanostructured Pt(Ti) product was formed after long milling time, which contained 44–47 at.% Ti and 53–56 at.% Pt. An ordered PtTi intermetallic was formed by annealing the metastable Pt(Ti) at temperature above 1300 °C. The crystal structure and microstructure of the TiPt phase depended on the milling time, annealing temperature and the cooling rate. The B19 PtTi plate martensite was formed after annealing at 1500 °C and quenching at a cooling rate of 23 °C/min to 200 °C/min for short time milled products. The width of martensite features was smaller at high cooling rate. In PtTi products milled for longer time, no martensitic transformation was observed on cooling the annealed samples. Small amounts of Pt 5 Ti 3 were formed in the powders milled for 16 h or more, followed by annealing at 1500 °C and furnace

CVD carbon powders modified by ball milling

Directory of Open Access Journals (Sweden)

Kazmierczak Tomasz

2015-09-01

Full Text Available Carbon powders produced using a plasma assisted chemical vapor deposition (CVD methods are an interesting subject of research. One of the most interesting methods of synthesizing these powders is using radio frequency plasma. This method, originally used in deposition of carbon films containing different sp2/sp3 ratios, also makes possible to produce carbon structures in the form of powder. Results of research related to the mechanical modification of these powders have been presented. The powders were modified using a planetary ball mill with varying parameters, such as milling speed, time, ball/powder mass ratio and additional liquids. Changes in morphology and particle sizes were measured using scanning electron microscopy and dynamic light scattering. Phase composition was analyzed using Raman spectroscopy. The influence of individual parameters on the modification outcome was estimated using statistical method. The research proved that the size of obtained powders is mostly influenced by the milling speed and the amount of balls. Powders tend to form conglomerates sized up to hundreds of micrometers. Additionally, it is possible to obtain nanopowders with the size around 100 nm. Furthermore, application of additional liquid, i.e. water in the process reduces the graphitization of the powder, which takes place during dry milling.

Estimating remediation costs for the Montclair radium superfund sites

International Nuclear Information System (INIS)

Turner, M.J.

1995-01-01

The Montclair/West Orange and Glen Ridge Superfund Sites, located in Essex County, NJ, are contaminated to varying degrees with radioactive materials. The waste originated from radium processing facilities prevalent in the area during the early 1900s. The design for remediation of these sites is managed by Bechtel National, Inc. on behalf of the United States Army Corps of Engineers, Kansas City District, which administers the project through an interagency agreement with the US Environmental Protection Agency (EPA). Design efforts for the project began in 1990. A portion of the scope, which is the topic of this article, was preparing the remediation costs estimates. These estimates were to be prepared from the detailed design packages; the Corps of Engineers required that the estimates were prepared using the Micro Computer-Aided Cost Estimating System (MCACES). This article discusses the design methods used, provides an overview of MCACES, and discusses the structure and preparation of the cost estimate and its uses. However, the main focus of the article is the methods used to generate the required project-specific cost estimate format for this project. 6 figs

Bifurcation and stability analysis of a nonlinear milling process

Science.gov (United States)

Weremczuk, Andrzej; Rusinek, Rafal; Warminski, Jerzy

2018-01-01

Numerical investigations of milling operations dynamics are presented in this paper. A two degree of freedom nonlinear model is used to study workpiece-tool vibrations. The analyzed model takes into account both flexibility of the tool and the workpiece. The dynamics of the milling process is described by the discontinuous ordinary differential equation with time delay, which can cause process instability. First, stability lobes diagrams are created on the basis of the parameters determined in impact test of an end mill and workpiece. Next, the bifurcations diagrams are performed for different values of rotational speeds.

Environmental impact of uranium mining and milling in Australia

International Nuclear Information System (INIS)

Levins, D.M.

1980-01-01

Australia has almost twenty per cent of the Western World's low-cost uranium reserves, located mostly in the Alligator Rivers region of the Northern Territory. At present, only one uranium mill is operating in Australia, but a number of new mills are planned for the early 1980s. Details are given of Australian uranium mining and milling proposals and the measures taken to minimize their environmental impact. Major factors affecting environmental impact are discussed, including treatment of liquid wastes, water management, control of radon and other airborne releases, and disposal of tailings. (auth)

MILLING MECHANICS OF MATERIALS ROLLED IN THICK LAYER

Directory of Open Access Journals (Sweden)

E. B. Lojechnikov

2006-01-01

Full Text Available Powder rolling conditions are systematized with the purpose of their compacting and milling. The generalized  condition of solid and free-flowing bulk material deformation is proposed in the  paper. The analytical solution of a stressed state of powder being shaped mechanically that ensures milling of its particles has been obtained.

Rough Mill Improvement Guide for Managers and Supervisors

Science.gov (United States)

Philip H. Mitchell; Jan Wiedenbeck; Bobby Ammerman; Bobby Ammerman

2005-01-01

Wood products manufacturers require an efficient recovery of product from lumber to remain profitable. A company's ability to obtain the best yield in lumber cut-up operations (i.e., the rough mill) varies according to the raw material, product, processing equipment, processing environment, and knowledge and skill of the rough mill's employees. This book...

Recycling of mill scale in sintering process

Directory of Open Access Journals (Sweden)

El-Hussiny N.A.

2011-01-01

Full Text Available This investigation deals with the effect of replacing some amount of Baharia high barite iron ore concentrate by mill scale waste which was characterized by high iron oxide content on the parameters of the sintering process., and investigation the effect of different amount of coke breeze added on sintering process parameters when using 5% mill scale waste with 95% iron ore concentrate. The results of this work show that, replacement of iron ore concentrate with mill scale increases the amount of ready made sinter, sinter strength and productivity of the sinter machine and productivity at blast furnace yard. Also, the increase of coke breeze leads to an increase the ready made sinter and productivity of the sintering machine at blast furnace yard. The productivity of the sintering machine after 5% decreased slightly due to the decrease of vertical velocity.

Characterization of prealloyed copper powders treated in high energy ball mill

International Nuclear Information System (INIS)

Rajkovic, Viseslava; Bozic, Dusan; Jovanovic, Milan T.

2006-01-01

The inert gas atomised prealloyed copper powders containing 3.5 wt.% Al were milled up to 20 h in the planetary ball mill in order to oxidize aluminium in situ with oxygen from the air. In the next procedure compacts from milled powder were synthesized by hot-pressing in argon atmosphere. Compacts from as-received Cu-3.5 wt.% Al powder and electrolytic copper powder were also prepared under the same conditions. Microstructural and morphological changes of high energy milled powder as well as changes of thermal stability and electrical conductivity of compacts were studied as a function of milling time and high temperature exposure at 800 deg. C. Optical, scanning electron microscopy (SEM) and X-ray diffraction analysis were performed for microstructural characterization, whereas thermal stability and electrical conductivity were evaluated by microhardness measurements and conductometer Sigmatest, respectively. The prealloyed 5 h-milled and compacted powder showed a significant increase in microhardness reaching the value of 2600 MPa, about 4 times greater than that of compacts synthesized from as-received electrolytic copper powder (670 MPa). The electrical conductivity of compacts from 5 h-milled powder was 52% IACS. The results were discussed in terms of the effect of small grain size and finely distributed alumina dispersoids on hardening and thermal stability of compacts

Effect of milling on the magnetic properties of Al–Mn obtained by mechanical alloying

International Nuclear Information System (INIS)

Betancourt, Mirna; Silva, Pedro; Gonzalez, Gema

2012-01-01

Highlights: ► Al–42 at.% Mn transforms to α-Mn(Al) by mechanical milling after 5 h of milling. ► Transformation to nano β-Mn is reached after 50 h of milling with 6 nm grain size. ► Milling strongly affects magnetic behavior. - Abstract: Al–Mn powders were prepared to obtain the compound Mn 42 Al 58 by mechanical alloying. The powders were milled during different periods (1 h, 5 h, 11.5 h, 15 h, 20 h and 50 h) using a SPEX 8000 mixer mill in nitrogen atmosphere. The materials were characterized by X-ray diffraction (XRD) and magnetic properties at room temperature, using a vibrating sample magnetometer (VSM). XRD shows partial transformation to α-Mn after only 1 h of milling and a mixture of α-Mn and β-Mn after 11.5 h of milling and further milling resulted in transformation to β-Mn phase with a grain size of 6 nm after 50 h. The change in magnetic properties with milling time is quite dramatic, from a ferromagnetic behavior for α-Mn(Al) to paramagnetic after 11.5 h of milling and showing again ferromagnetic behavior, with a strong increase of magnetization values of 5.5 emu/g, after 50 h of milling with formation of β-Mn(Al).

Eden Mills Community Hall energy audit prepared for Eden Mills going carbon neutral

Energy Technology Data Exchange (ETDEWEB)

Lay, R.; Aussant, C. [Enermodal Engineering Ltd., Kitchener, ON (Canada)

2009-04-22

This paper described an energy audit conducted as part of the Eden Mills going carbon neutral project during the spring and summer of 2008. The audit included an inspection of the Eden Mills community hall with a special focus on the building's mechanical system and building envelope. A blower door test was performed to depressurize the building and to measure the airtightness of the building envelope. An energy simulation model was then used to estimate energy use according to the buildings functions and components. Recommendations included the addition of wall insulation, the replacement of some windows, and improved return air ducting and warm air distribution systems. Various new thermostat control systems were also recommended, as well as the use of wood pellets in one of the hall's 2 furnaces. 20 tabs., 28 figs.

33 CFR 117.213 - New Haven Harbor, Quinnipiac and Mill Rivers.

Science.gov (United States)

2010-07-01

... Mill Rivers. 117.213 Section 117.213 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF... Haven Harbor, Quinnipiac and Mill Rivers. The draws of the Tomlinson bridge, mile 0.0, the Ferry Street... bridge, mile 0.4 across Mill River, shall operate as follows: (a) The draws shall open on signal; except...

A study on rheological characteristics of roller milled fenugreek fractions.

Science.gov (United States)

Sakhare, Suresh D; Inamdar, Aashitosh A; Prabhasankar, P

2016-01-01

Fenugreek seeds were fractionated by roller milling to get various fractions. The roller milled fractions and whole fenugreek flour (WFF) were evaluated for the flow behavior and time-dependent flow properties using a rotational viscometer at the temperatures of 10-60 (0)C. The samples subjected to a programmed shear rate increase linearly from 0 to 300 s(-1) in 3 min and successive decrease linearly shear rate from 300 s(-1) to 0 in 3 min. The roller milled fractions and WFF paste exhibited non-Newtonian pseudoplastic behavior. Difference in hysteresis loop area was observed among the roller milled fractions and WFF, being more noticeable at lower temperatures. Power law and Casson models were used to predict flow properties of samples. The power law model described well the flow behavior of the roller milled fractions and WFF at temperatures tested. Except flour (FL) fraction, consistency coefficient, m, increased with the temperature both in the forward and backward measurements. The roller milled fractions and WFF exhibited rheopectic behavior that increased viscosity with increasing the shear speed and the temperature. For all the sample tested, initial shear stress increased with increase in shear rate and temperature.

Palm Oil Milling Wastes and Sustainable Development

OpenAIRE

A. C. Er; Abd. R.M. Nor; Katiman Rostam

2011-01-01

Problem statement: Palm oil milling generates solid wastes, effluent and gaseous emissions. The aim of this study is to assess the progress made in waste management by the Malaysian palm oil milling sector towards the path of sustainable development. Sustainable development is defined as the utilization of renewable resources in harmony with ecological systems. Inclusive in this definition is the transition from low value-added to higher value-added transformation of waste...

Case Study: Fort Mill High School--A Culture of Continuous Improvement

Science.gov (United States)

Southern Regional Education Board (SREB), 2014

2014-01-01

This is the latest in a series of case studies highlighting best practices High Schools That Work (HSTW) network schools and districts are implementing to prepare students better for further studies and careers. Fort Mill High School is in Fort Mill, South Carolina, an outlying suburb of Charlotte, North Carolina. Fort Mill links high quality…

Energy conservation achievements by New Shorrock Mills, Ahmedabad

International Nuclear Information System (INIS)

Rawal, N.L.; Trivedi, R.M.

1994-01-01

The New Shorrock Mills, Ahmedabad is a textile mill manufacturing cloth. Managerial practices like energy auditing and energy conservation monitoring introduced to conserve energy are described. Various measures implemented to conserve energy in machines power; carding, winding, warping and sizing operations; auto looms and lighting power are described. Cost reduction in terms of rupees is given. (N.B.)

A study on thermal and mechanical properties of mechanically milled HDPE and PP

International Nuclear Information System (INIS)

Can, S.; Tan, S.

2003-01-01

In this study, mechanical mixing of HDPE and PP was performed via ball milling. Prepared compositions were 75/25 , 50/50 , 25/75 w/w HDPE/PP. Milling time and ball to powder ratio (B/P) were kept constant and system was cooled by adding solid CO 2 to improve the milling efficiency. To compare these systems with traditional methods, mixtures were also melt mixed by Brabender Plasti-Corder. Both milled and melt mixed systems were examined with DSC for thermal properties and tensile testing for mechanical properties Results are discussed by comparing milled , melt mixed and as-received polymers. It is observed that, unlike ball milled systems' in melt mixed systems mechanical properties are composition dependent. In addition , ball milling results in amorphization of both polymers and very high amounts of PP (75wt %) creates very amorphous HDPE structure. (Original)

Agglomeration during wet milling of LAST (lead-antimony-silver-tellurium) powders

International Nuclear Information System (INIS)

Hall, B.D.; Case, E.D.; Ren, F.; Johnson, J.R.; Timm, E.J.

2009-01-01

LAST (lead-antimony-silver-tellurium) compounds comprise a family of semiconducting materials with good thermoelectric properties. However, the as-cast form of LAST exhibits large grain size and hence low mechanical strength. Powder processing can produce a fine powder particle size that enhances fracture strength, however the powders tend to agglomerate if the individual powder diameters are less than a few microns across. Dry milling or wet milling (hexane additions of 0 cm 3 and 10 cm 3 ) produced hard agglomerates roughly 40 μm in diameter while wet milling with hexane additions of 25 cm 3 , 30 cm 3 or 50 cm 3 resulted in small, porous agglomerates roughly 20 μm in diameter. Thus, by adjusting the amount of milling liquid used while milling LAST powders, one can shift from hard to soft agglomerates, where the literature shows that soft agglomerates are less harmful to the final, sintered product. Also, in agreement with the results from the literature on other materials, wet milling of LAST powders produced smaller particle sizes but required longer times to reach the grindability limit

The MediaMill TRECVID 2012 semantic video search engine

NARCIS (Netherlands)

Snoek, C.G.M.; van de Sande, K.E.A.; Habibian, A.; Kordumova, S.; Li, Z.; Mazloom, M.; Pintea, S.L.; Tao, R.; Koelma, D.C.; Smeulders, A.W.M.

2012-01-01

In this paper we describe our TRECVID 2012 video retrieval experiments. The MediaMill team participated in four tasks: semantic indexing, multimedia event detection, multimedia event recounting and instance search. The starting point for the MediaMill detection approach is our top-performing

Influence of high-energy milling on structure and microstructure of asbestos-cement materials

Science.gov (United States)

Iwaszko, Józef; Zawada, Anna; Lubas, Małgorzata

2018-03-01

Asbestos-Containing Waste (ACW) in the form of a fragment from an asbestos-cement board was subjected to high-energy milling in a planetary mill at a constant rotational speed of 650 rpm and for variable milling times: 1, 2, and 3 h. The initial and the milled materials were subjected to infrared spectroscopic examination to identify the asbestos variety and to evaluate changes in the structure caused by high-energy milling. FT-IR (Fourier Transform Infrared Spectroscopy) examinations followed optical microscopy and SEM (Scanning Electron Microscopy) studies as well as X-ray analysis of the phase composition. It was found that the asbestos fibres present in the asbestos-cement board were respirable fibres with pathogenic properties. Identifying asbestos using the spectroscopic method showed that chrysotile asbestos was present in the as-received ACW while no characteristics of absorption bands from crocidolite or amosite were found. The results of the spectroscopic examinations were confirmed by the X-ray phase analysis. During SEM investigations of the milled ACW, complete loss of the fibrous structure of chrysotile was observed. The FT-IR examinations of the milled material showed that with an increased milling time, the characteristic absorption bands characteristic for chrysotile diminished and already after 2 h of milling their almost complete decay was observed. Thereby, it was confirmed that high-energy milling results in destruction of the crystalline structure of the asbestos phase. The conducted studies have shown that the treatment of asbestos-cement materials using high-energy milling is an effective method for asbestos disposal, capable of competing with other technologies and solutions. Moreover, FT-IR spectroscopy was found to be useful to identify asbestos phases and to assess changes caused by high-energy milling.

29 CFR 1910.216 - Mills and calenders in the rubber and plastics industries.

Science.gov (United States)

2010-07-01

... 29 Labor 5 2010-07-01 2010-07-01 false Mills and calenders in the rubber and plastics industries... Guarding § 1910.216 Mills and calenders in the rubber and plastics industries. (a) General requirements— (1... installed in accordance with this section and Subpart S of this part. (4) Mill roll heights. All new mill...

Integration of Succinic Acid Production in a Dry Mill Ethanol Facility

Energy Technology Data Exchange (ETDEWEB)

None

2006-08-01

This project seeks to address both issues for a dry mill ethanol biorefinery by lowering the cost of sugars with the development of an advanced pretreatment process, improving the economics of succinic acid (SA), and developing a model of an ethanol dry mill to evaluate the impact of adding different products and processes to a dry mill.

21 CFR 558.4 - Requirement of a medicated feed mill license.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Requirement of a medicated feed mill license. 558... Provisions § 558.4 Requirement of a medicated feed mill license. (a) A feed manufacturing facility must possess a medicated feed mill license in order to manufacture a Type B or Type C medicated feed from a...

Removal of contaminants in a paper mill effluent by Azolla caroliniana

Directory of Open Access Journals (Sweden)

D. Sivakumar

2015-09-01

Full Text Available This study was focused on removal of various parameters in paper mill effluent using a method called bioremediation by Azolla caroliniana.  The experimental investigations have been carried out using Azolla caroliniana for conducting the sorption study with various dilution ratios (2, 4, 6, 8, and 10, pH (3, 4, 5, 6, 7, 8 and 9 and biomass (200, 400, 600, 800 and 1000 g. The maximum removal percentage of TDS, BOD and COD in a paper mill effluent was obtained at the optimum dilution ratio of 6, pH of 8 and biomass of 800 g. The results of this study indicated that the maximum removal percentage of TDS, BOD and COD in a paper mill effluent was 82.3 %, 88.6 % and 79.1 % respectively.  Also, the study focused on uptake of TDS, BOD and COD in paper mill effluent by Azolla caroliniana through bioaccumulation factor and translocation factor. The results of bioaccumulation factor revealed that TDS, BOD and COD in paper mill effluent were adsorbed by Azolla caroliniana.  The results of translocation factor revealed that the roots of Azolla caroliniana translocate the TDS, BOD and COD in a paper mill effluent to the shoots of Azolla caroliniana. From the results, this study concluded that bioremediation by Azolla caroliniana could be effectively used for removing TDS, BOD and COD in a paper mill effluent. This study also suggested that Azolla caroliniana may be used for removing various contaminants, not only from paper mill effluent, but also from any other industrial effluents.

Phase transition of Ni-Mn-Ga alloy powders prepared by vibration ball milling

International Nuclear Information System (INIS)

Tian, B.; Chen, F.; Tong, Y.X.; Li, L.; Zheng, Y.F.; Liu, Y.; Li, Q.Z.

2011-01-01

Research highlights: → The vibration ball milling with a high milling energy introduces the atomic disorder and large lattice distortion in the alloy during milling and makes the formation of disordered fcc structure phase in the alloy. → The transition temperature and activation energy for disordered fcc → disordered bcc are ∼320 o C and 209 ± 8 kJ/mol, respectively. → The alloy powders annealed at 800 o C for 1 h show a one-stage martensitic transformation with quite lower latent heat compared to the bulk alloy. - Abstract: This study investigated the phase transformation of the flaky shaped Ni-Mn-Ga powder particles with thickness around 1 μm prepared by vibration ball milling and post-annealing. The SEM, XRD, DSC and ac magnetic susceptibility measurement techniques were used to characterize the Ni-Mn-Ga powders. The structural transition of Heusler → disordered fcc occurred in the powders prepared by vibration ball milling (high milling energy) for 4 h, which was different from the structural transition of Heusler → disordered fct of the powders fabricated by planetary ball milling (low milling energy) for 4 h. The two different structures after ball milling should be due to the larger lattice distortion occurred in the vibration ball milling process than in the planetary ball milling process. The structural transition of disordered fcc → disordered bcc took place at ∼320 o C during heating the as-milled Ni-Mn-Ga powders, which was attributed to the elimination of lattice distortion caused by ball milling. The activation energy for this transition was 209 ± 8 kJ/mol. The Ni-Mn-Ga powder annealed at 800 o C mainly contained Heusler austenite phase at room temperature and showed a low volume of martensitic transformation upon cooling. The inhibition of martensitic transformation might be attributed to the reduction of grain size in the annealed Ni-Mn-Ga particles.

Review of environmental aspects of uranium mill operations: industry's view

International Nuclear Information System (INIS)

Beverly, R.G.

1977-01-01

Problems faced by uranium mill operators in complying with new environmental regulations and guidelines are discussed. It is pointed out that valid data must be available in order to evaluate impacts on the environment, to determine background radiation levels, to measure the effectiveness of control techniques, and to determine compliance with standards and regulations. Specific problem areas facing mill operators today and some of the unresolved questions include: sampling methods and equipment for radon in ambient air, measurements of radon and radon daughter exposures of people, radon emanation rate meaurements applicable to monitoring mill tailings, the calibration of γ counters, measurements of population doses, regulations concerning mill tailings reclamation nd stabilization, and the comparative value of in-vivo counting and uranium urinary excretion measurements for monitoring personnel

Einstein-Yang-Mills-Lorentz black holes

Energy Technology Data Exchange (ETDEWEB)

Cembranos, Jose A.R.; Gigante Valcarcel, Jorge [Universidad Complutense de Madrid, Departamento de Fisica Teorica I, Madrid (Spain)

2017-12-15

Different black hole solutions of the coupled Einstein-Yang-Mills equations have been well known for a long time. They have attracted much attention from mathematicians and physicists since their discovery. In this work, we analyze black holes associated with the gauge Lorentz group. In particular, we study solutions which identify the gauge connection with the spin connection. This ansatz allows one to find exact solutions to the complete system of equations. By using this procedure, we show the equivalence between the Yang-Mills-Lorentz model in curved space-time and a particular set of extended gravitational theories. (orig.)

Barium Ferrite Ball Milled in Vacuum

International Nuclear Information System (INIS)

Campbell, S.J.; Wu, E.; Kaczmarek, W.A.; Wang, G.

1998-01-01

The structural and magnetic behaviour of BaFe 12 O 19 subjected to milling in vacuum for 1000 h has been investigated by x-ray powder diffraction and Moessbauer effect spectroscopy techniques. Pronounced structural disorder is obtained along with partial decomposition of BaFe 12 O 19 to α-Fe 2 O 3 and evidence for superparamagnetic relaxation effects due to the fine particles produced on milling. Restoration of the fully crystallised BaFe 12 O 19 structure on annealing at 1000 deg. C is accompanied by a six fold enhancement in the magnetic coercivity. This behaviour is linked with the fine crystallites

Continued care of uranium mill sites: some economic considerations

International Nuclear Information System (INIS)

Harrington, W.; Sawyer, J.W. Jr.

1978-01-01

A critique of recently enacted legislation authorizing the New Mexico Environmental Improvement Agency to regulate uranium mills in the state is presented. Under this new legislation, the Agency is authorized to require payment of up to 10 cents per pound of yellowcake from each licensed mill in the state until a total of $1 million has been deposited by that mill. The continued care fund thus created will provide for maintenance in perpetuity of mill sites after being decommissioned. Arguments are presented, based on calculations for a typical 5,000 ton per day mill, that even the maximum amount is not likely to generate sufficient income to support an adequate maintenance program. The matter is further aggravated by the rate of inflation which will increase costs beyond the coverage provided by a fixed funding system. To correct this situation, it is proposed that (1) the fund should generate an income stream sufficient to meet all maintenance costs based on currently available information on costs, interest, and inflation rates, and (2) the terms of the continued care contribution should be readily alterable as new information becomes available. The latter condition should be coupled with removal of the upper statutory limit now established for the fund

PULPA CUBA MILL ENERGY ASSESSMENT

Directory of Open Access Journals (Sweden)

Juan Pedro Hernández Touset

2015-10-01

Full Text Available An energy study was performed at Pulpa Cuba Paper Mill, located in Sancti Spiritus, where an energy management system was applied according to NC: ISO 50001, in order to assess the energy system by applying energy management systems for energy and water reduction in the paper mill, in which the current steam generation, distribution and consumption system is diagnosed. The proposal of a modified energy scheme with 1 MW Backpressure Steam Turbine Generator and rehabilitation of the original boiler or installing a lower capacity boiler contributes to save financial resources by the concept of water, fuel and electricity. The implementation of four projects will save 3,095,574 CUC / y and an average payback period of about 1 year is expected.

A QCD Model Using Generalized Yang-Mills Theory

International Nuclear Information System (INIS)

Wang Dianfu; Song Heshan; Kou Lina

2007-01-01

Generalized Yang-Mills theory has a covariant derivative, which contains both vector and scalar gauge bosons. Based on this theory, we construct a strong interaction model by using the group U(4). By using this U(4) generalized Yang-Mills model, we also obtain a gauge potential solution, which can be used to explain the asymptotic behavior and color confinement.

Ball Milling Assisted Solvent and Catalyst Free Synthesis of Benzimidazoles and Their Derivatives.

Science.gov (United States)

El-Sayed, Taghreed H; Aboelnaga, Asmaa; Hagar, Mohamed

2016-08-24

Benzoic acid and o-phenylenediamine efficiently reacted under the green solvent-free Ball Milling method. Several reaction parameters were investigated such as rotation frequency; milling balls weight and milling time. The optimum reaction condition was milling with 56.6 g weight of balls at 20 Hz frequency for one hour milling time. The study was extended for synthesis of a series of benzimidazol-2-one or benzimidazol-2-thione using different aldehydes; carboxylic acids; urea; thiourea or ammonium thiocyanate with o-phenylenediamine. Moreover; the alkylation of benzimidazolone or benzimidazolthione using ethyl chloroacetate was also studied.

DOJ News Release: New York Man Ordered to Pay Over $400,000 in Restitution and Fines for Role in Kickback Scheme at New Jersey Superfund Sites

Science.gov (United States)

WASHINGTON, D.C. – An Amherst, New York, man was ordered to pay over $400,000 in restitution and fines and placed on five years’ probation for his role in a kickback scheme at the Federal Creosote and Diamond Alkali Superfund sites in New Jersey.

40 CFR 406.10 - Applicability; description of the corn wet milling subcategory.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 28 2010-07-01 2010-07-01 true Applicability; description of the corn wet milling subcategory. 406.10 Section 406.10 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS GRAIN MILLS POINT SOURCE CATEGORY Corn Wet Milling...

40 CFR 406.20 - Applicability; description of the corn dry milling subcategory.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 28 2010-07-01 2010-07-01 true Applicability; description of the corn dry milling subcategory. 406.20 Section 406.20 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS GRAIN MILLS POINT SOURCE CATEGORY Corn Dry Milling...

On the bistable zone of milling processes.

Science.gov (United States)

Dombovari, Zoltan; Stepan, Gabor

2015-09-28

A modal-based model of milling machine tools subjected to time-periodic nonlinear cutting forces is introduced. The model describes the phenomenon of bistability for certain cutting parameters. In engineering, these parameter domains are referred to as unsafe zones, where steady-state milling may switch to chatter for certain perturbations. In mathematical terms, these are the parameter domains where the periodic solution of the corresponding nonlinear, time-periodic delay differential equation is linearly stable, but its domain of attraction is limited due to the existence of an unstable quasi-periodic solution emerging from a secondary Hopf bifurcation. A semi-numerical method is presented to identify the borders of these bistable zones by tracking the motion of the milling tool edges as they might leave the surface of the workpiece during the cutting operation. This requires the tracking of unstable quasi-periodic solutions and the checking of their grazing to a time-periodic switching surface in the infinite-dimensional phase space. As the parameters of the linear structural behaviour of the tool/machine tool system can be obtained by means of standard modal testing, the developed numerical algorithm provides efficient support for the design of milling processes with quick estimates of those parameter domains where chatter can still appear in spite of setting the parameters into linearly stable domains. © 2015 The Authors.

The MediaMill TRECVID 2010 semantic video search engine

NARCIS (Netherlands)

Snoek, C.G.M.; van de Sande, K.E.A.; de Rooij, O.; Huurnink, B.; Gavves, E.; Odijk, D.; de Rijke, M.; Gevers, T.; Worring, M.; Koelma, D.C.; Smeulders, A.W.M.

2010-01-01

In this paper we describe our TRECVID 2010 video retrieval experiments. The MediaMill team participated in three tasks: semantic indexing, known-item search, and instance search. The starting point for the MediaMill concept detection approach is our top-performing bag-of-words system of TRECVID

Accuracy of depth of cut in micro milling operations

DEFF Research Database (Denmark)

Bissacco, Giuliano

since the magnitude of the cutting forces involved is reduced), which make mechanical micromachining by use of miniaturized tools troublesome or even impossible. This study deals with the use of a conventional 3 axis vertical milling machine equipped with a high speed attached spindle for micro milling...

The MediaMill TRECVID 2011 semantic video search engine

NARCIS (Netherlands)

Snoek, C.G.M.; van de Sande, K.E.A.; Li, X.; Mazloom, M.; Jiang, Y.; Koelma, D.C.; Smeulders, A.W.M.

2011-01-01

In this paper we describe our TRECVID 2011 video retrieval experiments. The MediaMill team participated in two tasks: semantic indexing and multimedia event detection. The starting point for the MediaMill detection approach is our top-performing bag-of-words system of TRECVID 2010, which uses

Simple grain mill boosts production and eases women's workload ...

International Development Research Centre (IDRC) Digital Library (Canada)

2013-01-11

Jan 11, 2013 ... Simple grain mill boosts production and eases women's workload ... Farmers also like the design because, unlike other machines, it can be easily adjusted for different millet varieties and sizes. ... Local manufacturing. Discussions have begun with local entrepreneurs to manufacture the grain mill, which ...

Determination of the boundary conditions of the grinding load in ball mills

Science.gov (United States)

Sharapov, Rashid R.

2018-02-01

The prospects of application in ball mills for grinding cement clinker with inclined partitions are shown. It is noted that ball mills with inclined partitions are more effective. An algorithm is proposed for calculating the power consumed by a ball mill with inclined inter-chamber partitions in which an axial movement of the ball load takes place. The boundary conditions in which the ball load is located are determined. The equations of bounding the grinding load are determined. The behavior of a grinding load is considered in view of the characteristic cross sections. The coordinates of the centers of gravity of the grinding load with a definite step and the shape of the cross sections are determined. It is theoretically shown that grinding load in some parts of the ball mill not only consumes, but also helps to rotate the ball mill. Methods for calculating complex analytical expressions for determining the coordinates of the centers of gravity of the grinding load under the conditions of its longitudinal motion have developed. The carried out researches allow to approach from the general positions to research of behavior of a grinding load in the ball mills equipped with various in-mill devices.

77 FR 58120 - Inman Mills; Notice of Authorization for Continued Project Operation

Science.gov (United States)

2012-09-19

... DEPARTMENT OF ENERGY Federal Energy Regulatory Commission [Project No. 4362-000] Inman Mills... for a subsequent license was August 31, 2010. Inman Mills, the licensee for Project No. 4362, did not... the license from Inman Mills to Riverdale Development Venture, LLC. 115 FERC ] 62,076 (2006). However...

Processing of palm oil mill wastes based on zero waste technology

Science.gov (United States)

Irvan

2018-02-01

Indonesia is currently the main producer of palm oil in the world with a total production reached 33.5 million tons per year. In the processing of fresh fruit bunches (FFB) besides producing palm oil and kernel oil, palm oil mills also produce liquid and solid wastes. The increase of palm oil production will be followed by an increase in the production of waste generated. It will give rise to major environmental issues especially the discharge of liquid waste to the rivers, the emission of methane from digestion pond and the incineration of empty fruit bunches (EFB). This paper describes a zero waste technology in processing palm oil mill waste after the milling process. The technology involves fermentation of palm oil mill effluent (POME) to biogas by using continuous stirred tank reactor (CSTR) in the presence of thermophilic microbes, producing activated liquid organic fertilizer (ALOF) from discharge of treated waste effluent from biogas digester, composting EFB by spraying ALOF on the EFB in the composter, and producing pellet or biochar from EFB by pyrolysis process. This concept can be considered as a promising technology for palm oil mills with the main objective of eliminating the effluent from their mills.

Processing of magnetically anisotropic MnBi particles by surfactant assisted ball milling

Energy Technology Data Exchange (ETDEWEB)

Kanari, K. [Department of Physics, Aristotle University of Thessaloniki, 54124 Thessaloniki (Greece); Sarafidis, C., E-mail: hsara@physics.auth.gr [Department of Physics, Aristotle University of Thessaloniki, 54124 Thessaloniki (Greece); Gjoka, M.; Niarchos, D. [INN, NCSR Demokritos, Athens 15310 (Greece); Kalogirou, O. [Department of Physics, Aristotle University of Thessaloniki, 54124 Thessaloniki (Greece)

2017-03-15

MnBi particles are obtained from bulk MnBi using mechanochemical processing. The structure and magnetic properties of the MnBi particles are investigated by means of X-ray diffraction analysis, scanning electron microscopy and magnetometry. Surfactant assisted high energy ball milling results to the samples’ degradation even after one hour of milling. In the case of surfactant assisted low energy ball milling the increase of ball milling duration decreases the average particle size while the particles seem to be more separated. The saturation magnetization (M{sub s}) was found to decrease for large milling times beginning from 61 Am{sup 2}/kg, while the coercivity (μ{sub 0}H{sub c}) increases with the increase of ball milling duration up to 35 min where it reaches 1.62 T and thereafter it decreases. - Highlights: • Effect of surfactants in processing of MnBi. • Magnetization degradation due to air storage and due to processing. • Coercivity of 1.6 T in epoxy resin oriented material.

Uranium milling: Volume 1, Summary and text: Generic environmental impact statement: Draft

International Nuclear Information System (INIS)

1979-04-01

This generic environmental impact statement on uranium milling has been prepared in accordance with a notice of intent published by the Nuclear Regulatory Commission (NRC). The purpose of the statement is to assess the potential environmental impacts of uranium milling operations, in a programmatic context, including the management of uranium mill tailings, and to provide an opportunity for public participation in decisions on any proposed changes in NRC regulations based on this assessment. The principal objectives of the statement are to assess the nature and extent of the environmental impacts of uranium milling in the United states from local, regional, and national perspectives on both short- and long-term bases, to determine what regulatory actions are needed; to provide information on which to determine what regulatory requirements for management and disposal of mill tailings and mill decommissioning should be; and to support any rule makings that may be determined to be necessary. 39 figs., 130 tabs

Electropolishing or chemical milling of beryllium to remove machining defects

International Nuclear Information System (INIS)

Helms, J.R.

1975-12-01

The techniques of electropolishing and chemical milling to remove machine damage from beryllium are compared. Both techniques are found to be effective; chemical milling is recommended because it is easier to use and control

Health effects of uranium mining and milling for commercial nuclear power

International Nuclear Information System (INIS)

Branagan, E.F. Jr.; Gotchy, R.L.

1980-01-01

Radiological health effects potentially associated with uranium mining and milling have been estimated on both a regional and continental basis. Estimates of radon releases from mining were taken from testimony presented in licensing hearings during 1978. Estimates of the health effects from milling were derived from a draft NRC document titled Draft Generic Environmental Impact Statement on Uranium Milling. Health effects per annual fuel requirement (AFR) were presented on both a cumulative and continuous basis. In general, potential health effects to the general public because of both the mining and milling of one AFR are a very small fraction of the health effects caused by background radiation, on either a cumulative basis or a continuous basis. On a cumulative basis (from 1978 to the year 3000), potential health effects due to milling are about an order of magnitude less than those due to mining

Preventing performance drops of coal mills due to high moisture content

DEFF Research Database (Denmark)

Odgaard, Peter Fogh; Stoustrup, Jakob; Mataji, B.

2007-01-01

Coal mills pulverize and dry the coal dust before it is blown into the furnace in coal-fired power plants. The coal mills can only deliver the requested coal flow if certain conditions are fulfilled. These are normally considered as constraints on individual variables. However, combinations of more...... than one variable might cause problems even though these individually variables are in an acceptable region. This paper deals with such a problem. The combination of a high load of the power plant, a large load change and high moisture content in the coal, can force the coal mill into a state where...... coal is accumulated instead of being blown into the furnace. This paper suggests a simple method for preventing the accumulation of the coal in the mill, by limiting the requested coal flow considering the coal moisture content and the temperature outside the mill.  ...

Remedial design services for Montclair/West Orange and Glen Ridge Superfund sites

International Nuclear Information System (INIS)

Urbaniak, T.F.; Tomiczek, P.W. Jr.

1994-01-01

The Montclair/West Orange and Glen Ridge Superfund Sites are located 12 miles west of New York City in Essex County, New Jersey. The sites are contaminated with waste materials from radium-processing facilities which operated in the area during the early 1900's. The waste materials, containing radium and other radioactive isotopes were placed in three separate landfill sites. Major public health risks are indoor radon gas build-up and indoor/ outdoor gamma radiation. In 1989, the EPA issued a Record of Decision (ROD) which chose excavation and off-site disposal of material as the preferred alternative. The purpose of this presentation is to highlight key elements of the design process for the remedial action at Montclair. Those key elements are as follows: meeting community relations challenges; measuring radioactive contamination; developing plans and specifications; packaging of remedial action contacts; and continually improving both the process and the designs

Training manual for uranium mill workers on health protection from uranium

International Nuclear Information System (INIS)

McElroy, N.; Brodsky, A.

1986-01-01

This report provides information for uranium mill workers to help them understand the radiation safety aspects of working with uranium as it is processed from ore to yellowcake at the mills. The report is designed to supplement the radiation safety training provided by uranium mills to their workers. It is written in an easily readable style so that new employees with no previous experience working with uranium or radiation can obtain a basic understanding of the nature of radiation and the particular safety requirements of working with uranium. The report should be helpful to mill operators by providing training material to support their radiation safety training programs

Converting the Key Lake mill process for McArthur River ore

Energy Technology Data Exchange (ETDEWEB)

Rodgers, C. [McArthur River Operation, Cameco Corporation, Saskatoon, Saskatchewan (Canada)

2000-07-01

The Key Lake mill was commissioned in 1983 to process the two Key Lake ore deposits. With the depletion of these ore bodies in 1999, the plant was converted to mill the exceptionally rich McArthur River deposit located seventy eight kilometers northeast of the Key Lake mine site. This paper describes in detail the Key Lake milling process. The mill consists of a grinding circuit, a leach/counter current decantation circuit, a solvent extraction circuit, a yellowcake precipitation/calciner circuit, an ammonium sulphate crystallization circuit, and a waste treatment circuit. The paper also describes process changes to handle McArthur River ore, including the ore receiving station. (author)

Wood pellet milling tests in a suspension-fired power plant

DEFF Research Database (Denmark)

Masche, Marvin; Puig-Arnavat, Maria; Wadenbäck, Johan

2018-01-01

classification (i.e., the classifier cut size) are affected by the internal pellet particle size distribution obtained after pellet disintegration in hot water. Furthermore, optimal conditions for comminuting pellets were identified. The milling behavior was assessed by determining the specific grinding energy...... consumption and the differential mill pressure. The size and shape of comminuted pellets sampled from burner pipes were analyzed by dynamic image analysis and sieve analysis, respectively. The results showed that the internal pellet particle size distribution affected both the milling behavior...... similar. Mill operating changes had a negligible effect on the original elongated wood particle shape. To achieve the desired comminuted product fineness (i.e., the classifier cut size) with lower specific grinding energy consumption, power plant operators need to choose pellets with a finer internal...

Jet milling from a particle perspective : predicting particle fracture based on mechanical material properties

NARCIS (Netherlands)

Vegt, Onno Martinus

2007-01-01

Milling is a very old discipline originated in milling agricultural products to flour. Despite the enormous literature on size reduction, milling is a unit operation which has no sound underlying theory comparable to those existing for other unit operations. The design of milling equipment for a

Continuum regularized Yang-Mills theory

International Nuclear Information System (INIS)

Sadun, L.A.

1987-01-01

Using the machinery of stochastic quantization, Z. Bern, M. B. Halpern, C. Taubes and I recently proposed a continuum regularization technique for quantum field theory. This regularization may be implemented by applying a regulator to either the (d + 1)-dimensional Parisi-Wu Langevin equation or, equivalently, to the d-dimensional second order Schwinger-Dyson (SD) equations. This technique is non-perturbative, respects all gauge and Lorentz symmetries, and is consistent with a ghost-free gauge fixing (Zwanziger's). This thesis is a detailed study of this regulator, and of regularized Yang-Mills theory, using both perturbative and non-perturbative techniques. The perturbative analysis comes first. The mechanism of stochastic quantization is reviewed, and a perturbative expansion based on second-order SD equations is developed. A diagrammatic method (SD diagrams) for evaluating terms of this expansion is developed. We apply the continuum regulator to a scalar field theory. Using SD diagrams, we show that all Green functions can be rendered finite to all orders in perturbation theory. Even non-renormalizable theories can be regularized. The continuum regulator is then applied to Yang-Mills theory, in conjunction with Zwanziger's gauge fixing. A perturbative expansion of the regulator is incorporated into the diagrammatic method. It is hoped that the techniques discussed in this thesis will contribute to the construction of a renormalized Yang-Mills theory is 3 and 4 dimensions

John Stuart Mill on Freedom, Education, and Social Reform.

Science.gov (United States)

Carbone, Peter F.

1983-01-01

Examines the social philosophy of John Stuart Mill, emphasizing his views on freedom, education, and social reform. Considers Mill's individualism and reformism, the conflict between freedom and control that characterizes his work, and the importance of freedom and education. Suggests caution in drawing educational implications from his work. (DAB)

TREATABILITY STUDY REPORT OF GREEN MOUNTAIN LABORATORIES, INC.'S BIOREMEDIATION PROCESS, TREATMENT OF PCB CONTAMINATED SOILS, AT BEEDE WASTE OIL/CASH ENERGY SUPERFUND SITE, PLAISTOW, NEW HAMPSHIRE

Science.gov (United States)

In 1998, Green Mountain Laboratories, Inc. (GML) and the USEPA agreed to carry out a Superfund Innovative Technology Evaluation (SITE) project to evaluate the effectiveness of GML's Bioremediation Process for the treatment of PCB contaminated soils at the Beede Waste Oil/Cash Ene...

33 CFR 165.150 - New Haven Harbor, Quinnipiac River, Mill River.

Science.gov (United States)

2010-07-01

... River, Mill River. 165.150 Section 165.150 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF... New Haven Harbor, Quinnipiac River, Mill River. (a) The following is a regulated navigation area: The... 303°T to point D at the west bank of the mouth of the Mill River 41°18′05″ N, 72°54′23″ W thence south...

40 CFR 180.521 - Fumigants for grain-mill machinery; tolerances for residues.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 23 2010-07-01 2010-07-01 false Fumigants for grain-mill machinery... Tolerances § 180.521 Fumigants for grain-mill machinery; tolerances for residues. (a) General. Fumigants may be safely used in or on grain-mill machinery in accordance with the following prescribed conditions...

New relations for Einstein–Yang–Mills amplitudes

International Nuclear Information System (INIS)

Stieberger, Stephan; Taylor, Tomasz R.

2016-01-01

We obtain new relations between Einstein–Yang–Mills (EYM) amplitudes involving N gauge bosons plus a single graviton and pure Yang–Mills amplitudes involving N gauge bosons plus one additional vector boson inserted in a way typical for a gauge boson of a “spectator” group commuting with the group associated to original N gauge bosons. We show that such EYM amplitudes satisfy U(1) decoupling relations similar to Kleiss–Kuijf relations for Yang–Mills amplitudes. We consider a D-brane embedding of EYM amplitudes in the framework of disk amplitudes involving open and closed strings. A new set of monodromy relations is derived for mixed open–closed amplitudes with one closed string inserted on the disk world-sheet and a number of open strings at the boundary. These relations allow expressing the latter in terms of pure open string amplitudes and, in the field-theory limit, they yield the U(1) decoupling relations for EYM amplitudes.

Unravelling the relationship between degree of disorder and the dissolution behavior of milled glibenclamide

DEFF Research Database (Denmark)

Mah, Pei T; Laaksonen, Timo; Rades, Thomas

2014-01-01

Milling is an attractive method to prepare amorphous formulations as it does not require the use of solvents and is suitable for thermolabile drugs. One of the key critical quality attributes of milled amorphous formulations is their dissolution behavior. However, there are limited studies...... that have investigated the relationship between degree of disorder induced by milling and dissolution behavior. The main aim of this study was to identify the analytical technique used to characterize degree of disorder that correlates best with the recrystallization behavior during dissolution of milled...... glibenclamide samples. Solid state and surface changes during dissolution of milled glibenclamide samples were monitored in order to elucidate the processes that influence the dissolution behavior of milled glibenclamide samples. Glibenclamide was ball milled for different durations and analyzed using X...

Synthesis of ferrite nanoparticle by milling process for preparation of single domain magnet

International Nuclear Information System (INIS)

Suryadi; Hasbiyallah; Agus S W; Nurul TR; Budhy Kurniawan

2009-01-01

Study of ferrite nanoparticle synthesis for preparation of single domain magnet by milling of scrap magnet material have been done. Sample preparation were done using disk mill continued with high energy milling (HEM). Some powder were taken after 5, 10 dan 20 hours milling using HEM-E3D. The powder were then characterized using X-Ray Fluorescence (XRF), X-Ray Diffractometer (XRD) and Scanning Electron Microscope (SEM). XRF characterization result, confirmed by XRD analysis result, showed that the sample are of Strontium ferrite phase. Microstructure analysis result showed the occurrence of grain refining process of ferrite particle with increasing of milling time. Particle having size of nanometers successfully obtained, although in unhomogeneous distribution. Magnetic properties characterization result showed the increasing of hysteresis curve area of sample for longer milling time and sintering process. (author)

Ball milling of chalcopyrite: Moessbauer spectroscopy and XRD studies

International Nuclear Information System (INIS)

Pollak, H.; Fernandes, M.; Levendis, D.; Schonig, L.

1999-01-01

The aim of this project is to study the behavior of chalcopyrite under ball milling for extended periods in order to determine how it's decompose or transform. Tests were done with chalcopyrite mixed with iron and zinc with and without surfactant. The use of surfactants has various effects such as avoiding oxidation and clustering of the fine particles. In all case magnetic chalcopyrite is transformed into a paramagnetic component showing a disordered structure, thus revealing that Cu atoms have replaced Fe atoms. In the case of ball milling in air, chalcopyrite is decomposed with the lost of iron, while in milling under surfactants, iron enters into the chalcopyrite structure. (author)

Impacts of fiber orientation and milling on observed crystallinity in jack pine

Science.gov (United States)

Umesh P. Agarwal; Sally A. Ralph; Richard S. Reiner; Roderquita K. Moore; Carlos Baez

2014-01-01

Influences of fiber orientation and milling on wood cellulose crystallinity were studied using jack pine wood. The fiber orientation effects were measured by sampling rectangular wood blocks in radial, tangential, and cross-sectional orientations. The influence of milling was studied by analyzing the unsieved and sieved milled wood fractions (all

Massive Yang-Mills fields

NARCIS (Netherlands)

Veltman, M.J.G.; Reiff, J.

1969-01-01

Two problems are studied in the paper: (i) the relation between Lagrangian and Feynman rules if the Lagrangian contains derivative couplings and/or vector meson fields and (ii) the behaviour of certain two closed loop diagrams in the perturbation theory of Yang-Mills fields. With respect to ( i ) .

Production of nanocrystalline cermet thermal spray powders for wear resistant coatings by high-energy milling

International Nuclear Information System (INIS)

Eigen, N.; Klassen, T.; Aust, E.; Bormann, R.; Gaertner, F.

2003-01-01

TiC-Ni based nanocrystalline cermet powders for thermal spraying were produced by high-energy milling. Milling experiments were performed in an attrition mill and a vibration mill in kilogram scale, and powder morphologies and microstructures were characterized using scanning electron microscopy, X-ray diffraction, and laser scattering for particle size analysis. Milling time and powder input were optimized with respect to the desired microstructure and particle sizes, and the results using both types of mill were compared. Powders with homogeneously dispersed hard phase particles below 300 nm could be produced in both mills. Additional processes for the refinement of powder morphology and particle size distribution are discussed

John Stuart Mill's Philosophy of Persuasion

Directory of Open Access Journals (Sweden)

Helen Ruth McCabe

2014-02-01

Full Text Available In his youth, John Stuart Mill followed his father’s philosophy of persuasion but, in 1830, Mill adopted a new philosophy of persuasion, trying to lead people incrementally towards the truth from their original stand-points rather than engage them antagonistically. Understanding this change helps us understand apparent contradictions in Mill’s cannon, as he disguises some of his more radical ideas in order to bring his audience to re-assess and authentically change their opinions. It also suggests a way of re-assessing the relationship between Mill’s public and private works, to which we should look if we are attempting to understand his thought.

Hollow Mill for Extraction of Stripped Titanium Screws: An Easy ...

African Journals Online (AJOL)

countries. The known alternative in such condition is ... Key words: Hollow mill, stripped screws, titanium locked plates ... used a locally manufactured stainless steel hollow mill, ... head ‑ plate hole” assembly as a mono‑block single unit. In.

An ambitwistor Yang-Mills Lagrangian

International Nuclear Information System (INIS)

Mason, L.J.; Skinner, D.

2006-01-01

We introduce a Chern-Simons Lagrangian for Yang-Mills theory as formulated on ambitwistor space via the Ward, Isenberg, Yasskin, Green, Witten construction. The Lagrangian requires the selection of a codimension-2 Cauchy-Riemann submanifold which is naturally picked out by the choice of space-time reality structure and we focus on the choice of Euclidean signature. The action is shown to give rise to a space-time action that is equivalent to the standard one, but has just cubic vertices. We identify the ambitwistor propagators and vertices and work out their corresponding expressions on space-time and momentum space. It is proposed that this formulation of Yang-Mills theory underlies the recursion relations of Britto, Cachazo, Feng and Witten and provides the generating principle for twistor diagrams for gauge theory

Operating System For Numerically Controlled Milling Machine

Science.gov (United States)

Ray, R. B.

1992-01-01

OPMILL program is operating system for Kearney and Trecker milling machine providing fast easy way to program manufacture of machine parts with IBM-compatible personal computer. Gives machinist "equation plotter" feature, which plots equations that define movements and converts equations to milling-machine-controlling program moving cutter along defined path. System includes tool-manager software handling up to 25 tools and automatically adjusts to account for each tool. Developed on IBM PS/2 computer running DOS 3.3 with 1 MB of random-access memory.

Yang-Mills theory on the mass shell

International Nuclear Information System (INIS)

Cvitanovic, P.

1976-01-01

Gauge-invariant mass-shell amplitudes for quantum electrodynamics (QED) and Yang-Mills theory are defined by dimensional regularization. Gauge invariance of the mass-shell renormalization constants is maintained through interplay of ultraviolet and infrared divergences. Quark renormalizations obey the same simple Ward identity as do the electron renormalizations in QED, while the gluon contributions to gluon renormalizations are identically zero. The simplest amplitude finite in QED, the magnetic moment, is gauge-invariant but divergent in Yang-Mills theory for both external gluon and external photon

Torrefied Biomass Pellets—Comparing Grindability in Different Laboratory Mills

Directory of Open Access Journals (Sweden)

Jan Hari Arti Khalsa

2016-10-01

Full Text Available The firing and co-firing of biomass in pulverized coal fired power plants around the world is expected to increase in the coming years. Torrefaction may prove to be a suitable way of upgrading biomass for such an application. For transport and storage purposes, the torrefied biomass will tend to be in pellet form. Whilst standard methods for the assessment of the milling characteristics of coal exist, this is not the case for torrefied materials—whether in pellet form or not. The grindability of the fuel directly impacts the overall efficiency of the combustion process and as such it is an important parameter. In the present study, the grindability of different torrefied biomass pellets was tested in three different laboratory mill types; cutting mill (CM, hammer mill (HM and impact mill (IM. The specific grinding energy (SGE required for a defined mass throughput of pellets in each mill was measured and results were compared to other pellet characterization methods (e.g., durability, and hardness as well as the modified Hardgrove Index. Seven different torrefied biomass pellets including willow, pine, beech, poplar, spruce, forest residue and straw were used as feedstock. On average, the particle-size distribution width (across all feedstock was narrowest for the IM (0.41 mm, followed by the HM (0.51 mm and widest for the CM (0.62 mm. Regarding the SGE, the IM consumed on average 8.23 Wh/kg while CM and HM consumed 5.15 and 5.24 Wh/kg, respectively. From the three mills compared in this study, the IM seems better fit for being used in a standardized method that could be developed in the future, e.g., as an ISO standard.

Study of the Utah uranium-milling industry. Volume I. A policy analysis

International Nuclear Information System (INIS)

Turley, R.E.

1980-05-01

This is the first volume of a two volume study of the Utah Uranium Milling Industry. The study was precipitated by a 1977 report issued by the Western Interstate Nuclear Board entitled Policy Recommendations on Financing Stabilization. Perpetual Surveillance and Maintenance of Uranium Mill Tailings. Volume I of this study is a policy analysis or technology assessment of the uranium milling industry in the state of Utah; specifically, the study addresses issues that deal with the perpetual surveillance, monitoring, and maintenance of uranium tailings piles at the end of uranium milling operations, i.e., following shutdown and decommissioning. Volume II of this report serves somewhat as an appendix. It represents a full description of the uranium industry in the state of Utah, including its history and statements regarding its future. The topics covered in volume I are as follows: today's uranium industry in Utah; management of the industry's characteristic nuclear radiation; uranium mill licensing and regulation; state licensing and regulation of uranium mills; forecast of future milling operations; policy needs relative to perpetual surveillance, monitoring, and maintenance of tailings; policy needs relative to perpetual oversight; economic aspects; state revenue from uranium; and summary with conclusions and recommendations. Appendices, figures and tables are also presented

Comprehensive characterization of ball-milled powders simulating a tribofilm system

Energy Technology Data Exchange (ETDEWEB)

Häusler, I., E-mail: ines.haeusler@bam.de; Dörfel, I., E-mail: Ilona.doerfel@bam.de; Peplinski, B., E-mail: Burkhard.peplinski@bam.de; Dietrich, P.M., E-mail: Paul.dietrich@yahoo.de; Unger, W.E.S., E-mail: Wolfgang.Unger@bam.de; Österle, W., E-mail: Werner.Oesterle@bam.de

2016-01-15

A model system was used to simulate the properties of tribofilms which form during automotive braking. The model system was prepared by ball milling of a blend of 70 vol.% iron oxides, 15 vol.% molybdenum disulfide and 15 vol.% graphite. The resulting mixture was characterized by X-ray powder diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and various transmission electron microscopic (TEM) methods, including energy dispersive X-ray spectroscopy (EDXS), high resolution investigations (HRTEM) with corresponding simulation of the HRTEM images, diffraction methods such as scanning nano-beam electron diffraction (SNBED) and selected area electron diffraction (SAED). It could be shown that the ball milling caused a reduction of the grain size of the initial components to the nanometer range. Sometimes even amorphization or partial break-down of the crystal structure was observed for MoS{sub 2} and graphite. Moreover, chemical reactions lead to a formation of surface coverings of the nanoparticles by amorphous material, molybdenum oxides, and iron sulfates as derived from XPS. - Highlights: • Ball milling of iron oxides, MoS{sub 2}, and graphite to simulate a tribofilm • Increasing coefficient of friction after ball milling of the model blend • Drastically change of the diffraction pattern of the powder mixture • TEM & XPS showed the components of the milled mixture and the process during milling. • MoS{sub 2} and graphite suffered a loss in translation symmetry or became amorphous.

Fabrication of Ti-Ni-Cu shape memory alloy powders by ball milling method

International Nuclear Information System (INIS)

Kang, S.; Nam, T.

2001-01-01

Ti-Ni and Ti-Ni-Cu shape memory alloy powders have been fabricated by ball milling method, and then alloying behavior and transformation behavior were investigated by means of optical microscopy, electron microscopy, X-ray diffraction and differential scanning calorimetry. As milled Ti-Ni powders fabricated with milling time less than 20 hrs was a mixture of pure elemental Ti and Ni, and therefore it was unable to obtain alloy powders because the combustion reaction between Ti and Ni occurred during heat treatment. Since those fabricated with milling time more than 20 hrs was a mixture of Ti-rich and Ni-rich Ti-Ni solid solution, however, it was possible to obtain alloy powders without the combustion reaction during heat treatment. Clear exothermic and endothermic peaks appeared in the cooling and heating curves, respectively in DSC curves of 20 hrs and 30 hrs milled Ti-Ni powders. On the other hand, in DSC curves of 1 hr, 10 hrs, 50 hrs and 100 hrs, the thermal peaks were almost discernible. The most optimum ball milling time for fabricating Ti-Ni alloy powders was 30 hrs. Ti-40Ni-10Cu(at%) alloy powders were fabricated successfully by ball milling conditions with rotating speed of 100 rpm and milling time of 30 hrs. (author)

Temporal Chemical Data for Sediment, Water, and Biological Samples from the Lava Cap Mine Superfund Site, Nevada County, California-2006-2008

Science.gov (United States)

Foster, Andrea L.; Ona-Nguema, Georges; Tufano, Kate; White, Richard III

2010-01-01

The Lava Cap Mine is located about 6 km east of the city of Grass Valley, Nevada County, California, at an elevation of about 900 m. Gold was hosted in quartz-carbonate veins typical of the Sierran Gold Belt, but the gold grain size was smaller and the abundance of sulfide minerals higher than in typical deposits. The vein system was discovered in 1860, but production was sporadic until the 1930s when two smaller operations on the site were consolidated, a flotation mill was built, and a 100-foot deep adit was driven to facilitate drainage and removal of water from the mine workings, which extended to 366 m. Peak production at the Lava Cap occurred between 1934 and 1943, when about 90,000 tons of ore per year were processed. To facilitate removal of the gold and accessory sulfide minerals, the ore was crushed to a very fine sand or silt grain size for processing. Mining operations at Lava Cap ceased in June 1943 due to War Production Board Order L-208 and did not resume after the end of World War II. Two tailings retention structures were built at the Lava Cap Mine. The first was a log dam located about 0.4 km below the flotation mill on Little Clipper Creek, and the second, built in 1938, was a larger earth fill and rip-rap structure constructed about 2 km downstream, which formed the water body now called Lost Lake. The log dam failed during a storm that began on December 31, 1996, and continued into January 1997; an estimated 8,000-10,000 m3 of tailings were released into Little Clipper Creek during this event. Most of the fine tailings were deposited in Lost Lake, dramatically increasing its turbidity and resulting in a temporary 1-1.5 m rise in lake level due to debris blocking the dam spillway. When the blockage was cleared, the lake level quickly lowered, leaving a ?bathtub ring? of very fine tailings deposited substantially above the water line. The U.S. Environmental Protection Agency (EPA) initiated emergency action in late 1997 at the mine site to reduce

A new approach to the self-dual Yang-Mills equations

International Nuclear Information System (INIS)

Takasaki, K.

1984-01-01

Inspired by Sato's new theory for soliton equations, we find a new approach to the self-dual Yang-Mills equations. We first establish a correspondence of solutions between the self-dual Yang-Mills equations and a new system of equations with infinitely many unknown functions. It then turns out that the latter equations can be easily solved by a simple explicit procedure. This leads to an explicit description of a very broad class of solutions to the self-dual Yang-Mills equations, and also to a construction of transformations acting on these solutions. (orig.)

Comparison of five-axis milling and rapid prototyping for implant surgical templates.

Science.gov (United States)

Park, Ji-Man; Yi, Tae-Kyoung; Koak, Jai-Young; Kim, Seong-Kyoon; Park, Eun-Jin; Heo, Seong-Joo

2014-01-01

This study aims to compare and evaluate the accuracy of surgical templates fabricated using coordinate synchronization processing with five-axis milling and design-related processing with rapid prototyping (RP). Master phantoms with 10 embedded gutta-percha cylinders hidden under artificial gingiva were fabricated and imaged using cone beam computed tomography. Vectors of the hidden cylinders were extracted and transferred to those of the planned implants through reverse engineering using virtual planning software. An RP-produced template was fabricated by stereolithography in photopolymer at the RP center according to planned data. Metal sleeves were bonded after holes were bored (group RP). For the milled template, milling coordinates were synchronized using the conversion process for the coordinate synchronization platform located on the model's bottom. Metal bushings were set on holes milled on the five-axis milling machine, on which the model was fixed through the coordinate synchronization plate, and the framework was constructed on the model using orthodontic resin (group CS). A computed tomography image was taken with templates firmly fixed on models using anchor pins (RP) or anchor screws (CS). The accuracy was analyzed via reverse engineering. Differences between the two groups were compared by repeated measures two-factor analysis. From the reverse-engineered image of the template on the experimental model, RP-produced templates showed significantly larger deviations than did milled surgical guides. Maximum deviations of the group RP were 1.58 mm (horizontal), 1.68 mm (vertical), and 8.51 degrees (angular); those of the group CS were 0.68 mm (horizontal), 0.41 mm (vertical), and 3.23 degrees (angular). A comparison of milling and RP template production methods showed that a vector-milled surgical guide had significantly smaller deviations than did an RP-produced template. The accuracy of computer-guided milled surgical templates was within the safety

Preparation of glibenclamide nanocrystals by a simple laboratory scale ultra cryo-milling

Energy Technology Data Exchange (ETDEWEB)

Martena, Valentina; Censi, Roberta [University of Camerino, School of Pharmacy (Italy); Hoti, Ela; Malaj, Ledjan [University of Tirana, Department of Pharmacy (Albania); Martino, Piera Di, E-mail: piera.dimartino@unicam.it [University of Camerino, School of Pharmacy (Italy)

2013-06-15

The objective of this study is to evaluate the ability to reduce the particle size of glibenclamide (GBC) to the nanometric scale through a very simple and well-known laboratory scale method, the laboratory scale ultra cryo-milling. The effect of milling on GBC crystalline properties and dissolution behaviour was deliberately evaluated in the absence of any surfactants as stabilizers. The milling procedure consisted in adding particles to liquid nitrogen and milling them by hand in a mortar with a pestle for different time intervals (15, 30, 40 min). For comparison, the same milling procedure was also applied without liquid nitrogen. The particle size reduction was evaluated for the coarsest samples (>3 {mu}m) by measuring the particle Ferret's diameter through scanning electron microscopy, while for the smallest one (<3 {mu}m) by dynamic light scattering. A time grinding of 40 min in the presence of liquid nitrogen was revealed highly efficacious to obtain particles of nanodimensions, with a geometric mean particle size of 0.55 {+-} 0.23 {mu}m and more than the 80 % of particles lower than 1,000 nm. Interestingly, non-agglomerated particles were obtained. Differential scanning calorimetry and X-ray powder diffractometry allowed to assess that under mechanical treatment no polymorphic transitions were observed, while a decrease in crystallinity degree occurred depending on the milling procedure (presence or absence of liquid nitrogen) and the milling time (crystallinity decreases at increasing milling time from 15 to 40 min). A comparison of the intrinsic dissolution rate and the dissolution from particles revealed an interesting improvement of particle dissolution particularly for particles milled in the presence of liquid nitrogen due to an increase in particle surface area and concentration gradient, according to the Noyes-Whitney equation.

Kinetic parameters of grinding media in ball mills with various liner design and mill speed based on DEM modeling

Science.gov (United States)

Khakhalev, P. A.; Bogdanov, VS; Kovshechenko, V. M.

2018-03-01

The article presents analysis of the experiments in the ball mill of 0.5x0.3 m with four different liner types based on DEM modeling. The numerical experiment always complements laboratory research and allow obtaining high accuracy output data. An important property of the numerical experiment is the possibility of visualization of the results. The EDEM software allows calculating trajectory of the grinding bodies and kinetic parameters of each ball for the relative mill speed and the different types of mill’s liners.

Representation dependence of k -strings in pure Yang-Mills theory via supersymmetry

Science.gov (United States)

Anber, Mohamed M.; Pellizzani, Vito

2017-12-01

We exploit a conjectured continuity between super Yang-Mills on R3×S1 and pure Yang-Mills to study k -strings in the latter theory. As expected, we find that Wilson-loop correlation functions depend on the N-ality of a representation R to the leading order. However, the next-to-leading order correction is not universal and is given by the group characters, in the representation R , of the permutation group. We also study W-bosons in super Yang-Mills. We show that they are deconfined on the string world sheet, and therefore, they can change neither the string N-ality nor its tension. This phenomenon mirrors the fact that soft gluons do not screen probe charges with nonzero N-ality in pure Yang-Mills. Finally, we comment on the scaling law of k -strings in super Yang-Mills and compare our findings with strings in Seiberg-Witten theory, deformed Yang-Mills theory, and holographic studies that were performed in the 't Hooft large-N limit.

An Experiment Study on Surface Roughness in High Speed Milling NAK80 Die Steel

Directory of Open Access Journals (Sweden)

Su Fa

2016-01-01

Full Text Available The paper introduces that the high speed milling experiments on NAK80 die steel was carried out on the DMU 60 mono BLOCK five axis linkage high speed CNC machining center tool by the TiAlN coated tools, in order to research the effect of milling parameters on surface roughness Ra. The results showed that the Ra value increased with the decrease of milling speed vc, increased with the axial depth of milling ap, and feed per tooth fz and radial depth of milling ae. On the basis of the single factor experiment results, the mathematics model for between surface roughness and milling parameters were established by linear regression analysis.

Biota of uranium mill tailings near the Black Hills

Science.gov (United States)

Mark A. Rumble

1982-01-01

Reclamation" often implies the enhancement of the land as wildlife habitat or for other productive uses. However, there are situations where revegetation to stabilize erosion is the only desired goal. Uranium mining and mill sites may fall into this later category. Data pertaining to plant and animal components on revegetated uranium mill tailings was collected....

Counterbalance of cutting force for advanced milling operations

Science.gov (United States)

Tsai, Nan-Chyuan; Shih, Li-Wen; Lee, Rong-Mao

2010-05-01

The goal of this work is to concurrently counterbalance the dynamic cutting force and regulate the spindle position deviation under various milling conditions by integrating active magnetic bearing (AMB) technique, fuzzy logic algorithm and an adaptive self-tuning feedback loop. Since the dynamics of milling system is highly determined by a few operation conditions, such as speed of spindle, cut depth and feedrate, therefore the dynamic model for cutting process is more appropriate to be constructed by experiments, instead of using theoretical approach. The experimental data, either for idle or cutting, are utilized to establish the database of milling dynamics so that the system parameters can be on-line estimated by employing the proposed fuzzy logic algorithm as the cutting mission is engaged. Based on the estimated milling system model and preset operation conditions, i.e., spindle speed, cut depth and feedrate, the current cutting force can be numerically estimated. Once the current cutting force can be real-time estimated, the corresponding compensation force can be exerted by the equipped AMB to counterbalance the cutting force, in addition to the spindle position regulation by feedback of spindle position. On the other hand, for the magnetic force is nonlinear with respect to the applied electric current and air gap, the characteristics of the employed AMB is investigated also by experiments and a nonlinear mathematic model, in terms of air gap between spindle and electromagnetic pole and coil current, is developed. At the end, the experimental simulations on realistic milling are presented to verify the efficacy of the fuzzy controller for spindle position regulation and the capability of the dynamic cutting force counterbalance.

Prototyping of Dental Structures Using Laser Milling

Science.gov (United States)

Andreev, A. O.; Kosenko, M. S.; Petrovskiy, V. N.; Mironov, V. D.

2016-02-01

The results of experimental studies of the effect of an ytterbium fiber laser radiation parameters on processing efficiency and quality of ZrO2 ceramics widely used in stomatology are presented. Laser operating conditions with optimum characteristics for obtaining high quality final surfaces and rapid material removal of dental structures are determined. The ability of forming thin-walled ceramic structures by laser milling technology (a minimum wall thickness of 50 μm) is demonstrated. The examples of three-dimensional dental structures created in computer 3D-models of human teeth using laser milling are shown.

RANCANG BANGUN CNC MILLING MACHINEHOME MADE UNTUK MEMBUAT PCB

Directory of Open Access Journals (Sweden)

Dityo Pradana

2011-06-01

Full Text Available Kendala yang dimiliki oleh seorang penggemar elektronik untuk membuat PCB diantaranya adalah efisiensi waktu, tenaga, dan biaya. Pembuatan CNC milling machine merupakan salah satu solusi yang tepat untuk membuat PCB. CNC milling machine adalah mesin bubut otomatis yang bekerja atas dasar perintah Numerical Code. Rancang bangun CNC Milling Machine Home Made ini dikontrol oleh komputer yang akan mengontrol IC L297 melalui parallel port. IC L297 ini kemudian memberikan empat data digital a, b, c dan d untuk mengatur phase IC L298 yang menyalurkan tegangan untuk koil motor stepper unipolar. Pada akhirnya motor stepper unipolar akan memutar baut dan dapat menggerakkan meja sumbu menggunakan prinsip kerja ulir.

YANG-MILLS Theory in, Beyond, and Behind Observed Reality

Science.gov (United States)

Wilczek, Frank

The primary interactions of Yang-Mills theory [1] are visibly embodied in hard processes, most directly in jets. The character of jets also reflects the deep structure of effective charge, which is dominated by the influence of intrinsically non-Abelian gauge dynamics. These proven insights into fundamental physics ramify in many directions, and are far from being exhausted. I will discuss three rewarding explorations from my own experience, whose point of departure is the hard Yang-Mills interaction, and whose end is not yet in sight. Given an insight so profound and fruitful as Yang and Mills brought us, it is in order to try to consider its broadest implications, which I attempt at the end.

Observer-based Coal Mill Control using Oxygen Measurements

DEFF Research Database (Denmark)

Andersen, Palle; Bendtsen, Jan Dimon; S., Tom

2006-01-01

This paper proposes a novel approach to coal flow estimation in pulverized coal mills, which utilizes measurements of oxygen content in the flue gas. Pulverized coal mills are typically not equipped with sensors that detect the amount of coal injected into the furnace. This makes control...... of the coal flow difficult, causing stability problems and limits the plant's load following capabilities. To alleviate this problem without having to rely on expensive flow measurement equipment, a novel observer-based approach is investigated. A Kalman filter based on measurements of combustion air flow led...... into the furnace and oxygen concentration in the flue gas is designed to estimate the actual coal flow injected into the furnace. With this estimate, it becomes possible to close an inner loop around the coal mill itself, thus giving a better disturbance rejection capability. The approach is validated against...

Power Spectral Density Evaluation of Laser Milled Surfaces

Directory of Open Access Journals (Sweden)

Raoul-Amadeus Lorbeer

2017-12-01

Full Text Available Ablating surfaces with a pulsed laser system in milling processes often leads to surface changes depending on the milling depth. Especially if a constant surface roughness and evenness is essential to the process, structural degradation may advance until the process fails. The process investigated is the generation of precise thrust by laser ablation. Here, it is essential to predict or rather control the evolution of the surfaces roughness. Laser ablative milling with a short pulse laser system in vacuum (≈1 Pa were performed over depths of several 10 µm documenting the evolution of surface roughness and unevenness with a white light interference microscope. Power spectral density analysis of the generated surface data reveals a strong influence of the crystalline structure of the solid. Furthermore, it was possible to demonstrate that this effect could be suppressed for gold.

Occupational hearing loss of market mill workers in the city of Accra, Ghana.

Science.gov (United States)

Kitcher, Emmanuel D; Ocansey, Grace; Abaidoo, Benjamin; Atule, Alidu

2014-01-01

Noise induced hearing loss (NIHL) is an irreversible sensorineural hearing loss associated with exposure to high levels of excessive noise. Prevention measures are not well established in developing countries. This comparative cross sectional study aims to determine the prevalence of hearing loss in both a group of high risk workers and a control group and to assess their knowledge of the effects of noise on hearing health. A total of 101 market mill workers and 103 controls employed within markets in the city of Accra, Ghana, were evaluated using a structured questionnaire and pure tone audiometry. The questionnaire assessed factors including self-reported hearing loss, tinnitus, knowledge on the effects of noise on hearing health and the use of hearing protective devices. Pure tone audiometric testing was conducted for both mill workers and controls. Noise levels at the work premises of the mill workers and controls were measured. Symptoms of hearing loss were reported by 24 (23.76%) and 8 (7.7%) mill workers and controls respectively. Fifty-five (54.5%) and fifty-four (52.37%) mill workers and controls exhibited knowledge of the effects of noise on hearing health. Five (5.0%) mill workers used hearing protective devices. There was significant sensorineural hearing loss and the presence of a 4 kHz audiometric notch among mill workers when compared with controls for the mean thresholds of 2 kHz, 3 kHz and 4 kHz (P = 0. 001). The prevalence of hearing loss in the better hearing ears of the mill workers and controls was 24.8% and 4.8% respectively (P hearing loss, which may be characteristic of NIHL in the better hearing ears of the mill workers and controls was 24.8% and 4.8% respectively. The majority of mill workers did not use hearing protection.

Occupational hearing loss of market mill workers in the city of Accra, Ghana

Directory of Open Access Journals (Sweden)

Emmanuel D Kitcher

2014-01-01

Full Text Available Noise induced hearing loss (NIHL is an irreversible sensorineural hearing loss associated with exposure to high levels of excessive noise. Prevention measures are not well established in developing countries. This comparative cross sectional study aims to determine the prevalence of hearing loss in both a group of high risk workers and a control group and to assess their knowledge of the effects of noise on hearing health. A total of 101 market mill workers and 103 controls employed within markets in the city of Accra, Ghana, were evaluated using a structured questionnaire and pure tone audiometry. The questionnaire assessed factors including self-reported hearing loss, tinnitus, knowledge on the effects of noise on hearing health and the use of hearing protective devices. Pure tone audiometric testing was conducted for both mill workers and controls. Noise levels at the work premises of the mill workers and controls were measured. Symptoms of hearing loss were reported by 24 (23.76% and 8 (7.7% mill workers and controls respectively. Fifty-five (54.5% and fifty-four (52.37% mill workers and controls exhibited knowledge of the effects of noise on hearing health. Five (5.0% mill workers used hearing protective devices. There was significant sensorineural hearing loss and the presence of a 4 kHz audiometric notch among mill workers when compared with controls for the mean thresholds of 2 kHz, 3 kHz and 4 kHz (P = 0. 001. The prevalence of hearing loss in the better hearing ears of the mill workers and controls was 24.8% and 4.8% respectively (P < 0.5. The prevalence of hearing loss, which may be characteristic of NIHL in the better hearing ears of the mill workers and controls was 24.8% and 4.8% respectively. The majority of mill workers did not use hearing protection.

Challenges of fabricating plasmonic and photonic structures with Neon ion beam milling

DEFF Research Database (Denmark)

Leißner, Till; Fiutowski, Jacek; Bozhevolnyi, Sergey I.

-established electron beam lithography and focussed ion beam milling (FIB) using Gallium ions. These techniques, however, are to some extend limited in their resolution, and in addition Gallium and Carbon are implanted and deposited into the plasmonic structures during FIB process, potentially changing plasmonic...... properties. We are currently studying the capabilities of focussed Helium and Neon ion beam milling for the fabricating of plasmonic and photonic devices. We found that Neon ion beam milling enables us to prepare plasmonic structures, such as trenches (see Fig. 1) and V-grooves without doping and alloying...... effects specific to Galium FIB. Neon FIB milling is superior to Helium FIB milling in terms of the processing speed and smaller levels of implanted ions. From our perspective it is the most promising technique for the fabrication of individual plasmonic devices with a few nanometers precision. The main...

Research kinetic of motion of milling bodies in ball mill, outfit heat-exchange unit and calculation of its energy performance

Science.gov (United States)

Romanovich, A. A.; Romanovich, M. A.; Apukhtina, I. V.

2018-03-01

The article considers topical issues of energy saving in cement production with the use of a technological grinding complex, which includes a press roller grinder and a ball mill. Rational conditions of grinding are proposed for pre-shredded material through the installation of blade energy exchange devices (BEED) in the mill drum. The loading level in the first chamber varies periodically depending on the drum rotation angle, equipped with BEED. In the zone of BEED’s active action, there is a “scooping” of a part of grinding bodies together with crushed material, raising them to a height and giving them a longitudinally transverse movement, which is different from movement created in the mill without BEED. At the same time, additional work that consumes engine power is being done. A technique is proposed for calculating the additional engine power consumption of a mill, equipped with a BEED. This power is spent on creating a longitudinal-transverse motion of grinding bodies and its first and second chambers in areas of active influence of the BEED. Comparative analysis of results obtained experimentally and calculations of proposed equations show a high convergence of results. These analytical dependencies may be interest to Russian and foreign organizations that carry out their activities in the field of design and manufacture of cement equipment, as well as to cement producers.

Groundwater leaching of neutralized and untreated acid-leached uranium-mill tailings

International Nuclear Information System (INIS)

Gee, G.W.; Begej, C.W.; Campbell, A.C.; Sauter, N.N.; Opitz, B.E.; Sherwood, D.R.

1981-01-01

Tailings neutralization was examined to determine the effect of neutralization on contaminant release. Column leaching of acid extracted uranium mill tailings from Exxon Highland Mill, Wyoming, Pathfinder Gas Hills Mill, Wyoming, and the Dawn Midnite Mill, Washington, resulted in the flushing of high concentrations of salts in the first four pore volumes of leachate, followed by a steady decrease to the original groundwater salt concentrations. Neutralization decreased the concentration of salts and radionuclides leaching from the tailings and decreased the volume of solution required to return the solution to the groundwater pH and EC. Radium-226 and uranium-238 leached quickly from the tailings in the initial pore volumes of both neutralized and unneutralized tailings, and then decreased significantly. 6 figures, 5 tables

DEVELOPMENT OF A METHOD OF IMPROVEMENT OF QUALITY OF MILL PRODUCTS AND WEAR RESISTANCE OF THE TOOL AT THE ROLLING MILL 150 JSC «BSW – MANAGING COMPANY OF HOLDING «BMC»

Directory of Open Access Journals (Sweden)

I. A. Zuyeu

2016-01-01

Full Text Available Enhancement of calibration of mill rolls of the rolling mill 150, to improve of the mill products quality characteristics and to increase efficiency of the whole production is described in the article.

Getting nanometric MoO3 through chemical synthesis and high energy milling

International Nuclear Information System (INIS)

Santos-Beltrán, M.; Paraguay-Delgado, F.; Santos-Beltrán, A.; Fuentes, L.

2015-01-01

The effects of high energy mechanical milling (HEMM) were studied on the microstructure and optical properties of MoO 3 for hexagonal and orthorhombic phases. Employing HEMM was possible change particle size as a function of mechanical milling time, as well as the small quantity transformation percentage from hexagonal to orthorhombic phase. The relationship between microstrain and optical properties generated was studied. The electronic structures were calculated using the Density Functional Theory (DFT); to determinate partial density of state (PDOS). Band gap structure calculations show a good correlation between experimental and simulated data. The approximated values of microstrain, particle size, lattice parameters and oxygen vacancies were obtained employing the Rietveld refinement of X-ray diffraction patterns. Samples were characterized by electron microscopy techniques, surface area analysis (BET), thermal-gravimetric analysis (TGA), differential scanning calorimetry (DSC) and ultraviolet–visible spectroscopy (UV–Vis). It was possible, obtain particles with size below 40 nm by 30 min milling. - Graphical abstract: Orthorhombic phase, SEM image, SAED before milling, milling NPs, Particle size and band gap variation by milling time. - Highlights: • MoO 3 with hexagonal and orthorhombic structures was synthesized selectively. • By milling short time (30 m), it was possible get 40 nm diameter particles. • The band gap decrease for nanoparticles, then corroborated by simulation. • MoO 3 nanoparticles get high surface area for new technologic applications

Magnetic properties of nanocrystalline Fe–10%Ni alloy obtained by planetary ball mills

International Nuclear Information System (INIS)

Hamzaoui, Rabah; Elkedim, Omar

2013-01-01

Highlights: •Solid solution formation accompanied by a grain refinement for nanocrystalline Fe-Ni. •The shock mode process (SMP) prevails when Ω > >ω. •The friction mode process (FMP) is stronger when Ω < <ω. •The FMP leads to the formation of alloys exhibiting a soft magnetic behavior. -- Abstract: Planetary ball mill PM 400 from Retsch (with different milling times for Ω = 400 rpm, ω = 800 rpm) and P4 vario ball mill from Fritsch (with different milling conditions (Ω/ω), Ω and ω being the disc and the vial rotation speeds, respectively) are used for obtaining nanocrystalline Fe–10wt% Ni. The structure and magnetic properties are studied by using X-ray diffraction, SEM and hysteresis measurements, respectively. The bcc-Fe(Ni) phase formation is identified by X-ray diffraction. The higher the shock power and the higher milling time are, the larger the bcc lattice parameter and the lower the grain size. The highest value of the coercivity is 1600 A/m for Fe–10 wt.%Ni (with shock mode (424 rpm/100 rpm) after 36 h of milling), while the lowest value is 189 A/m for (400 rpm/800 rpm) after 72 h of milling. The milling performed in the friction mode has been found to lead the formation of alloys exhibiting a soft magnetic behavior for nanocrystalline Fe–10%Ni

Attritor milling of WC + 6% Co: Effects on powder characteristics and compaction behavior

International Nuclear Information System (INIS)

Mashl, S.J.; Smith, D.W.; Becking, G.H.; Hale, T.E.

1987-01-01

This study examines the effects of attritor milling on the characteristics and bulk behavior of fine tungsten carbide powders (initial median particle size ≅ 1.5 μm) blended with 6 wt. % cobalt (mps ≅ 1.5 μm). Experiments are performed in order to: Develop a process model relating the specific energy input to the milled median particle size. Examine the effect that changes in milling variables have on the specific energy - median particle size relationship. Observe the effects of variation in the initial particle size distribution on the as-milled particle size distribution, the compaction characteristics of the powder, and the shrinkage which will occur during sintering. The process model is based on Charles' equation, E-bar = A (d/sup -α/ - d/sub o//sup -α/) in which E-bar = the specific energy consumed in milling, d and d = the initial and milled median particle sizes respectively, and A and α are constants. Computer curve fitting techniques are employed to determine the values of the coefficient and exponent in the above equation. The resulting model predicts the experimental data within about +- over 10% over a significant range of d/sub o/ and E-Bar values. The apparent density and compactibility of the attritor milled powders are observed to be very sensitive to the milled particle size distribution

Control and prevention of seepage from uranium mill waste disposal facilities

International Nuclear Information System (INIS)

Williams, R.E.

1978-01-01

This paper constitutes an analysis of the technologies which are available for the prevention of movement of waste waters out of uranium mill waste disposal facilities via sub-surface routes. Hydrogeologic criteria for potential uranium mill waste disposal sites and mathematical modeling of contaminant migration in ground water are presented. Methods for prevention of seepage from uranium mill waste disposal facilities are investigated: liners, clay seals, synthetic polymeric membranes (PVC, polyethylene, chlorinated polyethylene, hypalon, butyl rubber, neoprene, elasticized polyolefin)

Case study: Montclair/West Orange and Glen Ridge Radium Superfund sites

International Nuclear Information System (INIS)

Pezzella, R.; Seppi, P.; Watson, D.

1994-01-01

The Montclair/West Orange and Glen Ridge Radium Sites are located 12 miles west of New York City in three residential communities in Essex County, New Jersey. The sites are contaminated with waste materials from a local radium processing facility which ceased operations in 1926. Houses were subsequently constructed on or near the radium waste disposal areas. The waste material was also used as backfill, which caused contamination to be spread randomly over the communities. There are 769 properties between four townships that comprise the Superfund sites. The Environmental Protection Agency (EPA) conducted an aerial survey in 1981 which identified the boundaries of the sites. In 1985, the New Jersey Department of Environmental Protection (NJDEP) began a pilot study to examine the feasibility of excavation and off-site disposal of contaminated material as a permanent solution. The study was interrupted when the permit for the disposal site was revoked by the state of Nevada. Since 1990 field testing has been completed on over 725 properties and remediation and restoration has been completed on 75 properties

76 FR 9593 - Proclaiming Certain Lands, Reykers Acquisition, as an Addition to the Bay Mills Indian...

Science.gov (United States)

2011-02-18

..., as an Addition to the Bay Mills Indian Reservation for the Bay Mills Indian Community of Michigan..., more or less, to be added to the Bay Mills Indian Reservation for the Bay Mills Indian Community of... the land described below. The land was proclaimed to be an addition to the Bay Mills Indian...

Performance of Color Camera Machine Vision in Automated Furniture Rough Mill Systems

Science.gov (United States)

D. Earl Kline; Agus Widoyoko; Janice K. Wiedenbeck; Philip A. Araman

1998-01-01

The objective of this study was to evaluate the performance of color camera machine vision for lumber processing in a furniture rough mill. The study used 134 red oak boards to compare the performance of automated gang-rip-first rough mill yield based on a prototype color camera lumber inspection system developed at Virginia Tech with both estimated optimum rough mill...

Uranium Mill and ISL Facility Database

Data.gov (United States)

U.S. Environmental Protection Agency — An Excel database on NRC and Agreement State licensed mills providing status, locational/operational/restoration data, maps, and environmental reports including...

Biotechnological applications for the utilisation of wastes from palm oil mills

Energy Technology Data Exchange (ETDEWEB)

Cheah, S C; Ma, A N; Ooi, L C.L.; Ong, A S.H.

1988-05-01

The milling of oil palm fruits produces about two-and-a-half to three times as much effluent as oil does. It also generates a large amount of lignocellulosic wastes, mainly in the form of empty fruit bunches, press cake fibres and nut shell. Research efforts at PORIM have been directed towards the utilisation of these wastes as a means to solve the problem of environmental pollution as well as for the generation of economic returns for the mills. We have studied a thermophilic contact process for the anaerobic digestion of palm oil mill effluent and its potential for generating biogas for energy uses. Our work has also shown that the condensate derived from the fruit sterilisation process during milling is amenable to fermentation for the production of single cell protein (SCP) and exo-enzymes. The enzymes produced have been applied for oil clarification, oil recovery from press cake fibers and saccharification of the fibers for the production of sugar feedstocks. This paper will also introduce the concept of integrated waste management for the palm oil mill through the implementation of these technologies.

Radiation hazards of uranium mining and milling

International Nuclear Information System (INIS)

Fry, R.M.

1975-09-01

This paper examines each of the radiological problems that arise in these processes and explains their scientific background. The major operational requirement is to ensure that exposure of miners over their working lives to radon and its daughter products does not lead to an unacceptable increase in their chance of contracting lung cancer. Studies on the incidence of lung cancer amongst underground uranium miners indicate that this risk will be small if lifetime exposures are kept below about 120 'working level months', even amongst underground miners who smoke cigarettes. The risk is much smaller again for miners who do not smoke cigarettes. Other hazards that must be controlled are exposure of miners and mill workers to external radiation and to dusts containing long-lived radioactive alpha emitting isotopes. Finally, the solid waste products from the mill (the tailings) which contain most of the naturally occurring radioactivity, must be properly impounded and after closure of the mill, stabilized to ensure long-term containment. Access by the public to the stabilized tailings must be controlled and habitation within the controlled area prohibited. (author)

John Stuart Mill on socialism and accountability

Directory of Open Access Journals (Sweden)

Francisco José Sales Rocha

2010-01-01

Full Text Available http://dx.doi.org/10.5007/1677-2954.2010v9n1p17 Este artigo mostra que o tipo de socialismo proposto por John Stuart Mill é marcado por uma forte preocupação com a controlabilidade do poder econômico e político. Ele rejeitou enfaticamente os modelos centralistas de socialismo por entender que eles levam a uma grande concentração de poder que compromete a liberdade. Para J. S. Mill, o socialismo deve ser implantado lentamente a partir de reformas amplamente discutidas que favoreçam a cidadania econômica dos trabalhadores, promovam a participação deles nas decisões referentes ao processo produtivo e em associações voluntárias. J. S. Mill acreditava que a competição econômica é essencial para o adequado funcionamento de uma economia socialista. Ele não esperava que tal economia se tornasse uma realidade em um futuro próximo.

Current practices and options for confinement of uranium mill tailings

International Nuclear Information System (INIS)

1981-01-01

At the United Nations Conference on the Human Environment, which took place in Stockholm from 4 to 6 June 1972, national governments were asked to explore, with the International Atomic Energy Agency and other appropriate international organizations, international co-operation on radioactive waste matters including those of mining and tailings disposal. Since that time the IAEA has been active in the field of uranium and thorium mill tailings management. As part of this activity, the present report describes current practices and options for confinement of uranium mill tailings. It is addressed to technical and administrative personnel who are involved in planning and implementing national and industrial programmes on the management of such tailings. In 1974 and 1975 the IAEA convened meetings of experts to review matters of interest and importance in the management of uranium and thorium mine and mill tailings. These activities led to the publication in 1976 of Management of Wastes from the Mining and Milling of Uranium and Thorium Ores, a Code of Practice and Guide to the Code, IAEA Safety Series No. 44. As a continuation of this activity, the IAEA is here dealing more specifically with the design and siting considerations for the management of uranium mill tailings

Suppressing Heavy Metal Leaching through Ball Milling of Fly Ash

Directory of Open Access Journals (Sweden)

Zhiliang Chen

2016-07-01

Full Text Available Ball milling is investigated as a method of reducing the leaching concentration (often termed stablilization of heavy metals in municipal solid waste incineration (MSWI fly ash. Three heavy metals (Cu, Cr, Pb loose much of their solubility in leachate by treating fly ash in a planetary ball mill, in which collisions between balls and fly ash drive various physical processes, as well as chemical reactions. The efficiency of stabilization is evaluated by analysing heavy metals in the leachable fraction from treated fly ash. Ball milling reduces the leaching concentration of Cu, Cr, and Pb, and water washing effectively promotes stabilization efficiency by removing soluble salts. Size distribution and morphology of particles were analysed by laser particle diameter analysis and scanning electron microscopy. X-ray diffraction analysis reveals significant reduction of the crystallinity of fly ash by milling. Fly ash particles can be activated through this ball milling, leading to a significant decrease in particle size, a rise in its BET-surface, and turning basic crystals therein into amorphous structures. The dissolution rate of acid buffering materials present in activated particles is enhanced, resulting in a rising pH value of the leachate, reducing the leaching out of some heavy metals.

40 CFR 429.120 - Applicability; description of the sawmills and planing mills subcategory.

Science.gov (United States)

2010-07-01

... sawmills and planing mills subcategory. 429.120 Section 429.120 Protection of Environment ENVIRONMENTAL... CATEGORY Sawmills and Planing Mills Subcategory § 429.120 Applicability; description of the sawmills and planing mills subcategory. This subpart applies to discharges to waters of the United States and to the...

Impact analysis of palm oil mill effluent on the aerobic bacterial ...

African Journals Online (AJOL)

AJB SERVER

2007-01-18

Jan 18, 2007 ... Key words: Palm oil mill effluent, total aerobic bacteria, ammonium oxidizers. INTRODUCTION ... bacteria help in the degradation of macromolecules from plant and animal .... Anaerobic digestion of palm oil mill effluent.

Integrability of N=3 super Yang-Mills equations

International Nuclear Information System (INIS)

Devchand, C.; Ogievetsky, V.

1993-10-01

We describe the harmonic superspace formulation of the Witten-Manin supertwistor correspondence for N=3 extended super Yang-Mills theories. The essence in that on being sufficiently supersymmetrised (up to the N=3 extension), the Yang-Mills equations of motion can be recast in the form of Cauchy-Riemann-like holomorphicity conditions for a pair of prepotentials in the appropriate harmonic superspace. This formulation makes the explicit construction of solutions a rather more tractable proposition than previous attempts. (orig.)

Superspace gauge fixing of topological Yang-Mills theories

Energy Technology Data Exchange (ETDEWEB)

Constantinidis, Clisthenis P; Piguet, Olivier [Universidade Federal do Espirito Santo (UFES) (Brazil); Spalenza, Wesley [Centro Brasileiro de Pesquisas Fisicas (CBPF), Rio de Janeiro (Brazil)

2004-03-01

We revisit the construction of topological Yang-Mills theories of the Witten type with arbitrary space-time dimension and number of ''shift supersymmetry'' generators, using a superspace formalism. The super-BF structure of these theories is exploited in order to determine their actions uniquely, up to the ambiguities due to the fixing of the Yang-Mills and BF gauge invariance. UV finiteness to all orders of perturbation theory is proved in a gauge of the Landau type. (orig.)

Superspace gauge fixing of topological Yang-Mills theories

International Nuclear Information System (INIS)

Constantinidis, Clisthenis P.; Piguet, Olivier; Spalenza, Wesley

2004-01-01

We revisit the construction of topological Yang-Mills theories of the Witten type with arbitrary space-time dimension and number of ''shift supersymmetry'' generators, using a superspace formalism. The super-BF structure of these theories is exploited in order to determine their actions uniquely, up to the ambiguities due to the fixing of the Yang-Mills and BF gauge invariance. UV finiteness to all orders of perturbation theory is proved in a gauge of the Landau type. (orig.)

Attempted - to -Phase Conversion of Croconic Acid via Ball Milling

Science.gov (United States)

2017-05-18

ARL-TN-0824 MAY 2017 US Army Research Laboratory Attempted α- to β-Phase Conversion of Croconic Acid via Ball Milling by...Laboratory Attempted α- to β-Phase Conversion of Croconic Acid via Ball Milling by Steven W Dean, Rose A Pesce-Rodriguez, and Jennifer A Ciezak...

Radiation pathways and potential health impacts from inactive uranium mill tailings

International Nuclear Information System (INIS)

1978-07-01

Radiation exposure pathways and potential health impacts were estimated as part of the evaluation of radioactive uranium mill tailings at the sites of inactive mills in eight western states. The purpose of this report is to describe in detail the methodology used in performing the pathway analysis and health effects estimations. In addition, specific parameters are presented for each of the 22 uranium mill sites that were evaluated. A computer program, RADAD, developed as part of this program, is described and listed

Accelerated aging tests of liners for uranium mill tailings disposal

International Nuclear Information System (INIS)

Barnes, S.M.; Buelt, J.L.; Hale, V.Q.

1981-11-01

This document describes the results of accelerated aging tests to determine the long-term effectiveness of selected impoundment liner materials in a uranium mill tailings environment. The study was sponsored by the US Department of Energy under the Uranium Mill Tailings Remedial Action Project. The study was designed to evaluate the need for, and the performance of, several candidate liners for isolating mill tailings leachate in conformance with proposed Environmental Protection Agency and Nuclear Regulatory Commission requirements. The liners were subjected to conditions known to accelerate the degradation mechanisms of the various liners. Also, a test environment was maintained that modeled the expected conditions at a mill tailings impoundment, including ground subsidence and the weight loading of tailings on the liners. A comparison of installation costs was also performed for the candidate liners. The laboratory testing and cost information prompted the selection of a catalytic airblown asphalt membrane and a sodium bentonite-amended soil for fiscal year 1981 field testing

Observer Based Fault Detection and Moisture Estimating in Coal Mill

DEFF Research Database (Denmark)

Odgaard, Peter Fogh; Mataji, Babak

2008-01-01

In this paper an observer-based method for detecting faults and estimating moisture content in the coal in coal mills is presented. Handling of faults and operation under special conditions, such as high moisture content in the coal, are of growing importance due to the increasing...... requirements to the general performance of power plants. Detection  of faults and moisture content estimation are consequently of high interest in the handling of the problems caused by faults and moisture content. The coal flow out of the mill is the obvious variable to monitor, when detecting non-intended drops in the coal...... flow out of the coal mill. However, this variable is not measurable. Another estimated variable is the moisture content, which is only "measurable" during steady-state operations of the coal mill. Instead, this paper suggests a method where these unknown variables are estimated based on a simple energy...

40 CFR 63.1343 - Standards for kilns and in-line kiln/raw mills.

Science.gov (United States)

2010-07-01

.../raw mills. 63.1343 Section 63.1343 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Industry Emission Standards and Operating Limits § 63.1343 Standards for kilns and in-line kiln/raw mills. (a) General. The provisions in this section apply to each kiln, each in-line kiln/raw mill, and any...

21 CFR 515.21 - Refusal to approve a medicated feed mill license application.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Refusal to approve a medicated feed mill license... SERVICES (CONTINUED) ANIMAL DRUGS, FEEDS, AND RELATED PRODUCTS MEDICATED FEED MILL LICENSE Administrative Actions on Licenses § 515.21 Refusal to approve a medicated feed mill license application. (a) The...

21 CFR 515.24 - Notice of revocation of a medicated feed mill license.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Notice of revocation of a medicated feed mill... SERVICES (CONTINUED) ANIMAL DRUGS, FEEDS, AND RELATED PRODUCTS MEDICATED FEED MILL LICENSE Administrative Actions on Licenses § 515.24 Notice of revocation of a medicated feed mill license. When a license...

Radiation protection in uranium mining and milling industry

International Nuclear Information System (INIS)

Raghavayya, M.

2005-01-01

The first phase of the Nuclear Fuel Cycle is exploration for uranium and the next is mining and milling of uranium ore. This phase is mostly characterised by low levels of radioactivity and radiation exposure of the workers involved. Yet it is a paradoxical truth that incidence of cancer among the work force, especially miners, due to occupational radiation exposure (from radon and decay products) has been proved only in uranium mines in the entire Nuclear Fuel Cycle. Of course such incidence occurred before the detrimental effect of radiation exposure was realised and understood. Therefore it is important to familiarise oneself with the radiation hazards prevalent in the uranium mining and milling facilities so as to take appropriate remedial measures for the protection of not only the workers but also the public at large. There are both open cast and underground uranium mines around the world. Radiation hazards are considerably less significant in open cast mines than in underground mines unless the ore grade is very high. By default therefore the discussion which ensues relates mainly to radiation hazards in underground uranium mines and associated milling operations. The discussion gives a brief outline of typical uranium mine and mining and milling operations. This is followed by a description of the radiation hazards therein and protection measures that are to be taken to minimise radiation exposure. (author)

TECHNOLOGICAL FEATURES OF MILLING AND FRACTIONATION OF FLAXSEEDS

Directory of Open Access Journals (Sweden)

A. Feskova

2015-01-01

Full Text Available Summary. The optimal parameters of milling and fractionation of flaxseeds were substantiated. It was found that the hull fraction with the highest content of lignan secoisolariciresinol diglucoside SDG was obtained when flaxseeds were grinded using a rotatory impact continuous operation mill at the rotation 1380-1640 rpm. Studies have shown that with the increasing of the rotor speed the number of unbriken seeds decreased. However, due to the fact that the shells are crushed more, they become more difficult to separate from the cotyledons. For identification and quantification of SDG the HPLC-MS method was used. It is found that the optimum separation membranes and cotyledon fraction occurs at sifting milled seeds sequentially through the sieves having meshes of 1 and 0.5 mm. The technology of industrial production of lignans-containing fraction and flour on the basis of flaxseeds processing were proposed. This technology includes milling flaxseeds at the rotation 1380-1640 rpm, with subsequent 2% silicon dioxide addition and stepwise sieving using sieves with the mesh size 2 mm. To use a fraction membranes high in lignans as raw material for biologically active additives to food it needed additional enforcement-ground to a size not more than 0.4 mm (technological features of capsulation. The developed technology allowed getting with maximum yields of lignans-containing fraction (10% yield and flaxseed flour (80% yield.

The Tool Life of Ball Nose end Mill Depending on the Different Types of Ramping

Science.gov (United States)

Vopát, Tomáš; Peterka, Jozef; Kováč, Martin

2014-12-01

The article deals with the cutting tool wear measurement process and tool life of ball nose end mill depending on upward ramping and downward ramping. The aim was to determine and compare the wear (tool life) of ball nose end mill for different types of copy milling operations, as well as to specify particular steps of the measurement process. In addition, we examined and observed cutter contact areas of ball nose end mill with machined material. For tool life test, DMG DMU 85 monoBLOCK 5-axis CNC milling machine was used. In the experiment, cutting speed, feed rate, axial depth of cut and radial depth of cut were not changed. The cutting tool wear was measured on Zoller Genius 3s universal measuring machine. The results show different tool life of ball nose end mills depending on the copy milling strategy.

Preparation of MgB2 superconducting microbridges by focused ion beam direct milling

Science.gov (United States)

Zhang, Xuena; Li, Yanli; Xu, Zhuang; Kong, Xiangdong; Han, Li

2017-01-01

MgB2 superconducting microbridges were prepared by focused ion beam (FIB) direct milling on MgB2 films. The surface topography of the microbridges were observed using SEM and AFM and the superconductivity was measured in this paper. Lots of cracks and holes were found near the milled area. And the superconducting transition temperature was decreased a lot and the bridges prepared were not superconducting due to ion damage after milled with large dose. Through these works, we explored the effect regular of FIB milling and experimental parameters on the performance of microbridges.

Fabrication of Al-20 wt%Si powder using scrap Si by ultra high-energy milling process

Energy Technology Data Exchange (ETDEWEB)

Kang, Won-Kyung [Division of Advanced Materials Engineering and Institute for Rare Metals, Kongju National University, 275, Budae-dong, Cheonan, Chungnam 330-717 (Korea, Republic of); Y Latin-Small-Letter-Dotless-I lmaz, Fikret [Department of Physics, Faculty of Art and Science, Gaziosmanpasa University, Tasliciftlik Campus, 60240 Tokat (Turkey); Kim, Hyo-Seob; Koo, Jar-Myung [Division of Advanced Materials Engineering and Institute for Rare Metals, Kongju National University, 275, Budae-dong, Cheonan, Chungnam 330-717 (Korea, Republic of); Hong, Soon-Jik, E-mail: hongsj@kongju.ac.kr [Division of Advanced Materials Engineering and Institute for Rare Metals, Kongju National University, 275, Budae-dong, Cheonan, Chungnam 330-717 (Korea, Republic of)

2012-09-25

Highlights: Black-Right-Pointing-Pointer High energy ball milling process has been successfully employed to produce Al-20Si alloy using scrap Si powders. Black-Right-Pointing-Pointer Fully finer and homogenous structure could be achieved after 60 min of milling time. Black-Right-Pointing-Pointer Si particles were not dissolved but uniformly dispersed in the Al matrix in a milled state. Black-Right-Pointing-Pointer The hardness of as-milled Al-20Si powder increased steadily with the increase of milling time. Black-Right-Pointing-Pointer Grain size and dispersion strengthening are two mechanisms being responsible for hardness increment. - Abstract: In this study, microstructural evolution and mechanical properties of Al-20 wt%Si and pure Al powders fabricated by ultra high-energy ball milling technique were investigated as a function of milling time. The microstructure and mechanical properties of the as-milled powders were examined by scanning electron microscope (SEM), energy dispersive spectrometry (EDS), X-ray diffractometer (XRD) and Vickers hardness tester. SEM observation showed that the particle size increased at an early stage of milling, and then decreased drastically with further milling. XRD and cross-sectional EDS-mapping analyses revealed that Si particles were not dissolved but uniformly dispersed in the Al matrix in a milled state. Vickers hardness of both pure Al and Al-Si powder increases with milling time, which attributes to the grain size strengthening and dispersion strengthening.

Superfund at work: Hazardous waste cleanup efforts nationwide, fall 1992. (Wide Beach section of Brant, New York)

International Nuclear Information System (INIS)

1992-01-01

Wide-spread contamination of polychlorinated biphenyls (PCBs) threatened the Wide Beach section of Brant, New York, a popular vacation resort. EPA's Superfund program effectively completed a permanent cleanup of Wide Beach in the span of one year. Other highlights included: a new and innovative technology to remove PCB contamination; reduction of PCBs to one-fifth of acceptable levels; temporary relocation of residents who were concerned for their health while cleanup activities took place; newly paved roads and driveways, re-landscaped yards, and a new storm sewer system; and restoration of ecologically sensitive wetlands. EPA's achievements significantly reduced PCB risks at Wide Beach, and left a satisfied community in Brant

Surface modification of titanium hydride with epoxy resin via microwave-assisted ball milling

International Nuclear Information System (INIS)

Ning, Rong; Chen, Ding; Zhang, Qianxia; Bian, Zhibing; Dai, Haixiong; Zhang, Chi

2014-01-01

Highlights: • TiH 2 was modified with epoxy resin by microwave-assisted ball milling. • The epoxy ring was opened under the coupling effect of microwave and ball milling. • Microwave-assisted ball milling improved the compatibility of TiH 2 with epoxy. - Abstract: Surface modification of titanium hydride with epoxy resin was carried out via microwave-assisted ball milling and the products were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), thermo-gravimetry (TG) and Fourier transform infrared spectroscopy (FT-IR). A sedimentation test was performed to investigate the compatibility of the modified nano titanium hydride with the epoxy resin. The results show that the epoxy resin molecules were grafted on the surface of nano titanium hydride particles during the microwave-assisted ball milling process, which led to the improvement of compatibility between the nanoparticles and epoxy resin. According to the FT-IR, the grafting site was likely to be located around the epoxy group due to the fact that the epoxy ring was opened. However, compared with microwave-assisted ball milling, the conventional ball milling could not realize the surface modification, indicating that the coupling effect of mechanical force and microwave played a key role during the process

Design and Testing of UMM Vertical Ball Mill (UVBM) for producing Aluminium Powder

Science.gov (United States)

Aisyah, I. S.; Caesarendra, Wahyu; Suprihanto, Agus

2018-04-01

UMM Vertical Ball Mill (UVBM) was intended to be the apparatus to produce metal powder with superior characteristic in production rate while retaining good quality of metal powder. The concept of design was adopting design theory of Phal and Beitz with emphasis on increasing of probability of success in engineering and economy aspects.Since it was designed as vertical ball mill, a new way to produce powder, then it need to be tested for the performance after manufactured. The test on UVBM was carried out by milling of aluminium chip for 5 (five) different milling time of 0.5 hours, 1 hour, 3 hours, 5 hours and 7 hours, and the powder product then be characterized for it morphology and size using Scanning Electron Microscope (SEM) and Sieve.The results of the study were the longer of the milling time, the finer of the powder. From the test results of SEM, the morphology of the powder with 5 variations of milling time were most of the powder in form of flake (flat), small round and angular (irregular). The distribution of powder size was best obtained on the variation of milling time 3 hours, 5 hours, and 7 hours with percentage of 200 mesh in size of 22.14 %, 64 % and 91.25 % respectively.

Performance of Disk Mill Type Mechanical Grinder for Size Reducing Process of Robusta Roasted Beans

Directory of Open Access Journals (Sweden)

Sri Mulato

2006-12-01

Full Text Available One of improtant steps in secondary coffee processing that influence on final product quality such as consistency and uniformity is milling process. Usually, Indonesian smallholder used "lumpang" for milling coffee roasted beans to coffee powder product which caused the final product not uniformed and consistent, and low productivity. Milling process of coffee roasted beans can be done by disk mill type mechanical grinder which is used by smallholder for milling several cereals. Indonesian Coffee and Cocoa Research Institute have developed disk mill type grinding machine for milling coffee roasted beans. Objective of this research is to find performance of disk mill type grinding machine for size reducing process of Robusta roasted beans from several size dried beans and roasting level treatments. Robusta dried beans which are taken from dry processing method have 13—14% moisture content (wet basis, 680—685 kg/m3 density, and classified in 3 sizes level. The result showed that the disk mill type of grinding machine could be used for milling Robusta roasted beans. Machine hascapacity 31—54 kg/h on 5,310—5,610 rpm axle rotation and depend on roasting level. Other technical parameters were 91—98% process efficientcy, 19—31 ml/ kg fuel consumption, 0.3—1% slips, 50—55% particles had diameter less than 230 mesh and 38—44% particles had diameter bigger than 100 mesh, 32—38% lightness was increased, 0.6—12.6% density was decreased, and solubility of coffee powder between 28—30%. Cost milling process per kilogram of Robusta roasted beans which light roast on capacity 30 kg/hour was Rp362.9. Key words : Coffee roasted, Robusta, disk mill, mechanical grinder, size reduction.

Hume, Mill, Hill, and the sui generis epidemiologic approach to causal inference.

Science.gov (United States)

Morabia, Alfredo

2013-11-15

The epidemiologic approach to causal inference (i.e., Hill's viewpoints) consists of evaluating potential causes from the following 2, noncumulative angles: 1) established results from comparative, observational, or experimental epidemiologic studies; and 2) reviews of nonepidemiologic evidence. It does not involve statements of statistical significance. The philosophical roots of Hill's viewpoints are unknown. Superficially, they seem to descend from the ideas of Hume and Mill. Hill's viewpoints, however, use a different kind of evidence and have different purposes than do Hume's rules or Mill's system of logic. In a nutshell, Hume ignores comparative evidence central to Hill's viewpoints. Mill's logic disqualifies as invalid nonexperimental evidence, which forms the bulk of epidemiologic findings reviewed from Hill's viewpoints. The approaches by Hume and Mill cannot corroborate successful implementations of Hill's viewpoints. Besides Hume and Mill, the epidemiologic literature is clueless about a plausible, pre-1965 philosophical origin of Hill's viewpoints. Thus, Hill's viewpoints may be philosophically novel, sui generis, still waiting to be validated and justified.

Effect of high-energy ball milling in the structural and textural properties of kaolinite

Directory of Open Access Journals (Sweden)

E. C. Leonel

2014-06-01

Full Text Available Through the process of high-energy ball milling it is possible to obtain solid materials with higher surface area and different particle sizes. These characteristics are very important for some application such as adsorption. Besides, applications of some clays depend on the functionalization which, for kaolinite, takes place in the aluminol groups. Modification in the structural and textural properties of kaolinite by high-energy milling can improve functionalization of kaolinite due to the exposure of aluminol groups. In this work studies were done on the influence of high-energy ball milling on the morphological properties of kaolinite, taking into account parameters such as filling of the miller, number of balls and amount of mass to be milled. Moreover, studies involving milling kinetics of purified kaolinite were carried out to verify modification in the morphology of kaolinite with milling time.

Environmental Development Plan: uranium mining, milling, and conversion

International Nuclear Information System (INIS)

1979-08-01

This Environmental Development Plan (EDP) identifies the planning and management requirements and schedules needed to evaluate and assess the environmental, health, and safety (EH and S) aspects of the uranium mining, milling, and conversion technologies. The plan represents the collective perceptions of EH and S concerns and requirements and knowledge of ongoing research programs of most of the Federal agencies involved in significant EH and S R and D program management, standards setting, or regulatory activities associated with uranium mining, milling, and conversion

Yang-Mills-Vlasov system in the temporal gauge

International Nuclear Information System (INIS)

Choquet-Bruhat, Y.; Noutchegueme, N.

1991-01-01

We prove a local in time existence theorem of a solution of the Cauchy problem for the Yang-Mills-Vlasov integrodifferential system. Such equations govern the evolution of plasmas, for instance of quarks and gluons (quagmas), where non abelian gauge fields and Yang-Mills charges replace the usual electromagnetic field and electric charge. We work with the temporal gauge and use functional spaces with appropriate weight on the momenta, but no fall off is required in the space direction [fr

Superspace gauge fixing of topological Yang-Mills theories

International Nuclear Information System (INIS)

Constantinidis, Clisthenis P.; Piguet, Olivier; Spalenza, Wesley

2003-10-01

We revisit the construction of topological Yang-Mills theories of the Witten type with arbitrary space-time dimension and number of 'shift supersymmetry' generators, using a superspace formalism. The super-B F structure of these theories is exploited in order to determine their actions uniquely, up to the ambiguities due to the fixing of the Yang-Mills and B F gauge invariance. UV finiteness to all orders of perturbation theory is proved in a gauge of the Landau type. (author)

Superspace gauge fixing of topological Yang-Mills theories

Energy Technology Data Exchange (ETDEWEB)

Constantinidis, Clisthenis P; Piguet, Olivier [Espirito Santo Univ. (UFES), Vitoria, ES (Brazil); Spalenza, Wesley

2003-10-15

We revisit the construction of topological Yang-Mills theories of the Witten type with arbitrary space-time dimension and number of 'shift supersymmetry' generators, using a superspace formalism. The super-B F structure of these theories is exploited in order to determine their actions uniquely, up to the ambiguities due to the fixing of the Yang-Mills and B F gauge invariance. UV finiteness to all orders of perturbation theory is proved in a gauge of the Landau type. (author)

Dynamical CP violation of the generalized Yang-Mills model

International Nuclear Information System (INIS)

Wang Dianfu; Chang Xiaojing; Sun Xiaoyu

2011-01-01

Starting from the generalized Yang-Mills model which contains, besides the vector part V μ , also a scalar part S and a pseudoscalar part P . It is shown, in terms of the Nambu-Jona-Lasinio (NJL) mechanism, that CP violation can be realized dynamically. The combination of the generalized Yang-Mills model and the NJL mechanism provides a new way to explain CP violation. (authors)

A connection between the Einstein and Yang-Mills equations

International Nuclear Information System (INIS)

Mason, L.J.; Newman, E.T.

1989-01-01

It is our purpose here to show an unusual relationship between the Einstein equations and the Yang-Mills equations. We give a correspondence between solutions of the self-dual Einstein vacuum equations and the self-dual Yang-Mills equations with a special choice of gauge group. The extension of the argument to the full Yang-Mills equations yields Einstein's unified equations. We try to incorporate the full Einstein vacuum equations, but the approach is incomplete. We first consider Yang-Mills theory for an arbitrary Lie-algebra with the condition that the connection 1-form and curvature are constant on Minkowski space. This leads to a set of algebraic equations on the connection components. We then specialize the Lie-algebra to be the (infinite dimensional) Lie algebra of a group of diffeomorphisms of some manifold. The algebraic equations then become differential equations for four vector fields on the manifold on which the diffeomorphisms act. In the self-dual case, if we choose the connection components from the Lie-algebra of the volume preserving 4-dimensional diffeomorphism group, the resulting equations are the same as those obtained by Ashtekar, Jacobsen and Smolin, in their remarkable simplification of the self-dual Einstein vacuum equations. (An alternative derivation of the same equations begins with the self-dual Yang-Mills connection now depending only on the time, then choosing the Lie-algebra as that of the volume preserving 3-dimensional diffeomorphisms). When the reduced full Yang-Mills equations are used in the same context, we get Einstein's equations for his unified theory based on absolute parallelism. To incorporate the full Einstein vacuum equations we use as the Lie group the semi-direct product of the diffeomorphism group of a 4-dimensional manifold with the group of frame rotations of an SO(1, 3) bundle over the 4-manifold. This last approach, however, yields equations more general than the vacuum equations. (orig.)

Determination of milling parameters to obtain mechanosynthesized ZnFe2O4

International Nuclear Information System (INIS)

Jean, Malick; Nachbaur, Virginie

2008-01-01

In this work, the mechanosynthesis of zinc ferrite in WC vials is studied. Millings are performed under air, with a planetary ball-milling, starting from elemental oxides α-Fe 2 O 3 and ZnO. As-milled powders are structurally and magnetically characterized by X-ray diffraction and Moessbauer spectroscopy. Milling parameters as rotational speeds of main disc and vials are particularly discussed in terms of influence on the obtaining of a pure zinc ferrite phase. These parameters have a strong influence on injected power, on radial and tangential components of the impact force. Friction phenomenon, associated with injected power, have been found to be the governing parameters of the end product

Effect of milling on DSC thermogram of excipient adipic acid.

Science.gov (United States)

Ng, Wai Kiong; Kwek, Jin Wang; Yuen, Aaron; Tan, Chin Lee; Tan, Reginald

2010-03-01

The purpose of this research was to investigate why and how mechanical milling results in an unexpected shift in differential scanning calorimetry (DSC) measured fusion enthalpy (Delta(fus)H) and melting point (T(m)) of adipic acid, a pharmaceutical excipient. Hyper differential scanning calorimetry (hyper-DSC) was used to characterize adipic acid before and after ball-milling. An experimental study was conducted to evaluate previous postulations such as electrostatic charging using the Faraday cage method, crystallinity loss using powder X-ray diffraction (PXRD), thermal annealing using DSC, impurities removal using thermal gravimetric analysis (TGA) and Karl Fischer titration. DSC thermograms showed that after milling, the values of Delta(fus)H and T(m) were increased by approximately 9% and 5 K, respectively. Previous suggestions of increased electrostatic attraction, change in particle size distribution, and thermal annealing during measurements did not explain the differences. Instead, theoretical analysis and experimental findings suggested that the residual solvent (water) plays a key role. Water entrapped as inclusions inside adipic acid during solution crystallization was partially evaporated by localized heating at the cleaved surfaces during milling. The correlation between the removal of water and melting properties measured was shown via drying and crystallization experiments. These findings show that milling can reduce residual solvent content and causes a shift in DSC results.

Investigation of planetary milling for nano-silicon carbide reinforced aluminium metal matrix composites

Energy Technology Data Exchange (ETDEWEB)

Kollo, Lauri, E-mail: lauri.kollo@staff.ttu.e [Laboratory of Advanced Materials Processing, EMPA, Feuerwerkerstrasse 39, 3602 Thun (Switzerland); Department of Materials Engineering, Tallinn University of Technology, Ehitajate tee 5, 19086 Tallinn (Estonia); Leparoux, Marc; Bradbury, Christopher R.; Jaeggi, Christian [Laboratory of Advanced Materials Processing, EMPA, Feuerwerkerstrasse 39, 3602 Thun (Switzerland); Carreno-Morelli, Efrain; Rodriguez-Arbaizar, Mikel [University of Applied Sciences of Western Switzerland, Design and Materials Unit, 1950 Sion (Switzerland)

2010-01-21

High-energy planetary milling was used for mixing aluminium powders with 1 vol.% of silicon carbide (SiC) nanoparticles. A number of milling parameters were modified for constituting the relationship between the energy input from the balls and the hardness of the bulk nanocomposite materials. It was shown that mixing characteristics and reaction kinetics with stearic acid as process control agent can be estimated by normalised input energy from the milling bodies. For this, the additional parameter characterising the vial filling was determined experimentally. Depending on the ball size, a local minimum in filling parameter was found, laying at 25 or 42% filling of the vial volume for the balls with diameter of 10 and 20 mm, respectively. These regions should be avoided to achieve the highest milling efficiency.After a hot compaction, fourfold difference of hardness for different milling conditions was detected. Therewith the hardness of the Al-1 vol.% nanoSiC composite could be increased from 47 HV{sub 0.5} of pure aluminium to 163 HV{sub 0.5} when milling at the highest input energy levels.

New approach to recycling and waste-to-energy in paper production, Urban Mill

Energy Technology Data Exchange (ETDEWEB)

Ristola, P. [Metso Corporation (Finland)

2002-10-01

Greenfield paper mills are commonly perceived as massive investments with a high level of associated impact on the local environment. Parallel to this, increasingly strict targets are being set by modem legislation for reducing waste disposal at landfills. One long-term solution to this dilemma lies in extended materials recycling, combined with effective utilisation of waste as energy. Metso Paper's Urban Mill is a unique pilot concept that promises to become an important part of such a solution. The novelty of Metso Paper's new eco-efficient Urban Mill concept lies in its combination of a small paper mill with using solid waste to generate energy. The roots of the concept go back to the early 1990s, when several mini-mills were built to produce raw materials for corrugated containers in North America. The competitiveness of mini-mills like this is based on several benefits: lowcost, high-quality waste paper raw material, utilisation of adjacent facilities for utilities, and modern machines with lean manning and low inbound and outbound logistics costs.

The Tool Life of Ball Nose end Mill Depending on the Different Types of Ramping

Directory of Open Access Journals (Sweden)

Vopát Tomáš

2014-12-01

Full Text Available The article deals with the cutting tool wear measurement process and tool life of ball nose end mill depending on upward ramping and downward ramping. The aim was to determine and compare the wear (tool life of ball nose end mill for different types of copy milling operations, as well as to specify particular steps of the measurement process. In addition, we examined and observed cutter contact areas of ball nose end mill with machined material. For tool life test, DMG DMU 85 monoBLOCK 5-axis CNC milling machine was used. In the experiment, cutting speed, feed rate, axial depth of cut and radial depth of cut were not changed. The cutting tool wear was measured on Zoller Genius 3s universal measuring machine. The results show different tool life of ball nose end mills depending on the copy milling strategy.

Bioremediation of ground water contaminants at a uranium mill tailings site

International Nuclear Information System (INIS)

Barton, L.L.; Nuttall, H.E.; Thomson, B.M.; Lutze, W.

1995-01-01

Ground water contaminated with uranium from milling operations must be remediated to reduce the migration of soluble toxic compounds. At the mill tailings site near Tuba City, Arizona (USA) the approach is to employ bioremediation for in situ immobilization of uranium by bacterial reduction of uranyl, U(VI), compounds to uraninite, U(IV). In this initial phase of remediation, details are provided to indicate the magnitude of the contamination problem and to present preliminary evidence supporting the proposition that bacterial immobilization of uranium is possible. Additionally, consideration is given to contaminating cations and anions that may be at toxic levels in ground water at this uranium mill tailing site and detoxification strategies using bacteria are addressed. A model concept is employed so that results obtained at the Tuba City site could contribute to bioremediation of ground water at other uranium mill tailings sites

Assessment of heavy metals introduced into food through milling process: health implications

International Nuclear Information System (INIS)

Adeti, P.J.

2015-07-01

The present study was conducted to characterised and assesss heavy metal contamination in food through milling process and their health implications. Grinding plate made from Ghana, India and Nigeria purchased from the Ghanaian open market were used for this work. Maize from the same farm was milled into flour using the three grinding plate inserted into three different corn milling machines operating on commercial bases. Th first grinding was done immediately after the insertion of the newly sharpened plates into the machines. The plates were left for continuous daily usage. Subsequent milling of the maize was done after intervals of one month. The grinding plates and maize flour was analysed using Atomic absorption spectrophometer (AAS). The resultes recorded indicated that the heavy metals content o the Ghanaian, Indian and Nigerian made plates had the e similar metal contents but varied in terms of the individual metal concentrations. Flour from the Ghanaian made plates had the highest level of contaminants with the least from that of the Indian made plates. Generally, the highest levels of contamination were observed in the fist milling for the three plates as compared to the three subsequent milling at monthly interval. The contamination levels showed a decreasing trend from the first month (first milling ) to the fourth month (fourth milling). Cu, Cr and Ni showed concentrations above the permissible limit set by FAO/WHO in milled maize using Ghanaian made plate. Copper (Cu) recorded a concentration value between 15.04 mg/kg to 10.21mg.kg, 11.25 mg/kg to 9.13mg/kg and 10.36mg/kg and 9.68mg/kg using the Ghanaian-, Indian and Nigerian made plate respectively. Chromium (Cr) recorded a concentration between 1.51 mg/kg to 0.96 mg/kg, 1.03mg/kg to 0.91 mg/kg and 0.98mg/kg to 0.80 mg/kg using Ghanaian-, Indian and Nigerian made plates respectively. Nickel (Ni) recorded a concentration value between 23.23 mg/kg to 10.43 mg/kg, 11.46mg/kg to 10.43 mg/kg and 12.55 mg

Mill and mental phenomena: critical contributions to a science of cognition.

Science.gov (United States)

Bistricky, Steven L

2013-06-01

Attempts to define cognition preceded John Stuart Mill's life and continue to this day. John Stuart Mill envisioned a science of mental phenomena informed by associationism, empirical introspection, and neurophysiology, and he advanced specific ideas that still influence modern conceptions of cognition. The present article briefly reviews Mill's personal history and the times in which he lived, and it traces the evolution of ideas that have run through him to contemporary cognitive concepts. The article also highlights contemporary problems in defining cognition and supports specific criteria regarding what constitutes cognition.

A Generalized Yang-Mills Model and Dynamical Breaking of Gauge Symmetry

International Nuclear Information System (INIS)

Wang Dianfu; Song Heshan

2005-01-01

A generalized Yang-Mills model, which contains, besides the vector part V μ , also a scalar part S, is constructed and the dynamical breaking of gauge symmetry in the model is also discussed. It is shown, in terms of Nambu-Jona-Lasinio (NJL) mechanism, that the gauge symmetry breaking can be realized dynamically in the generalized Yang-Mills model. The combination of the generalized Yang-Mills model and the NJL mechanism provides a way to overcome the difficulties related to the Higgs field and the Higgs mechanism in the usual spontaneous symmetry breaking theory.

Health risks from uranium mill tailings

International Nuclear Information System (INIS)

Russell, J.L.

1992-01-01

This paper reviews the risk to public health and the environment from uranium mill tailings. The steps taken by the Environmental Protection Agency (EPA) to reduce this risk from tailing are summarized

Modeling of Surface Geometric Structure State After Integratedformed Milling and Finish Burnishing

Science.gov (United States)

Berczyński, Stefan; Grochała, Daniel; Grządziel, Zenon

2017-06-01

The article deals with computer-based modeling of burnishing a surface previously milled with a spherical cutter. This method of milling leaves traces, mainly asperities caused by the cutting crossfeed and cutter diameter. The burnishing process - surface plastic treatment - is accompanied by phenomena that take place right in the burnishing ball-milled surface contact zone. The authors present the method for preparing a finite element model and the methodology of tests for the assessment of height parameters of a surface geometrical structure (SGS). In the physical model the workpieces had a cuboidal shape and these dimensions: (width × height × length) 2×1×4.5 mm. As in the process of burnishing a cuboidal workpiece is affected by plastic deformations, the nonlinearities of the milled item were taken into account. The physical model of the process assumed that the burnishing ball would be rolled perpendicularly to milling cutter linear traces. The model tests included the application of three different burnishing forces: 250 N, 500 N and 1000 N. The process modeling featured the contact and pressing of a ball into the workpiece surface till the desired force was attained, then the burnishing ball was rolled along the surface section of 2 mm, and the burnishing force was gradually reduced till the ball left the contact zone. While rolling, the burnishing ball turned by a 23° angle. The cumulative diagrams depict plastic deformations of the modeled surfaces after milling and burnishing with defined force values. The roughness of idealized milled surface was calculated for the physical model under consideration, i.e. in an elementary section between profile peaks spaced at intervals of crossfeed passes, where the milling feed fwm = 0.5 mm. Also, asperities after burnishing were calculated for the same section. The differences of the obtained values fall below 20% of mean values recorded during empirical experiments. The adopted simplification in after-milling

Dependence of hydrogen storage characteristics of mechanically milled carbon materials on their host structures

International Nuclear Information System (INIS)

Shindo, K.; Kondo, T.; Sakurai, Y.

2004-01-01

We investigated whether the hydrogen storage characteristics of carbon materials prepared by mechanical milling in an H 2 atmosphere were dependent on their host structures. We used natural graphite (NG) and activated carbon fibers (ACF) and compared them with activated carbon (AC) powders. The XRD patterns of NG and ACF milled for over 20 h and SEM images of these samples milled for 80 h were almost the same as those of AC. The hydrogen storage capacities of NG and ACF estimated by the inert gas fusion-thermal conductivity method increased with the mechanical milling time up to 10 h and showed little milling time dependence thereafter. The capacities of NG and ACF reached about 3.0 wt.% and were similar to that of AC. However, it should be noted that the hydrogen storage mechanism of NG and ACF mechanically milled in an H 2 atmosphere might be different because the changes in their specific surface areas with milling time were opposite. Thermal desorption mass spectroscopy (TDS) revealed that the desorption spectra of the hydrogen molecules (mass number=2) of NG and ACF milled for 10 h in the same way as AC contained two peaks at about 500 and 800 deg. C. The desorption activation energies of hydrogenated NG and ACF at these peaks calculated from a Kissinger plot were almost with the same as those of hydrogenated AC. This suggests that the state of the hydrogen trapped in the structural defects in NG introduced by the mechanical milling may be almost the same as that of AC. In addition, we assumed the possibility that the state of the hydrogen in ACF hydrogenated by mechanical milling could be almost the same as that in hydrogenated AC. We considered that the nanocarbon materials hydrogenated under our milling conditions had very similar physical shapes and hydrogen storage capacities, independent of their host structures

76 FR 2409 - Proclaiming Certain Lands, Lot 32 Acquisition, as an Addition to the Bay Mills Indian Reservation...

Science.gov (United States)

2011-01-13

..., as an Addition to the Bay Mills Indian Reservation for the Bay Mills Indian Community of Michigan..., more or less, to be added to the Bay Mills Indian Reservation for the Bay Mills Indian Community of... Mills Indian Reservation and part of the Bay Mills Indian Community of Michigan for the exclusive use of...

Surface topography and roughness of high-speed milled AlMn1Cu

Science.gov (United States)

Wang, Zhenhua; Yuan, Juntang; Yin, Zengbin; Hu, Xiaoqiu

2016-10-01

The aluminum alloy AlMn1Cu has been broadly applied for functional parts production because of its good properties. But few researches about the machining mechanism and the surface roughness were reported. The high-speed milling experiments are carried out in order to improve the machining quality and reveal the machining mechanism. The typical topography features of machined surface are observed by scan electron microscope(SEM). The results show that the milled surface topography is mainly characterized by the plastic shearing deformation surface and material piling zone. The material flows plastically along the end cutting edge of the flat-end milling tool and meanwhile is extruded by the end cutting edge, resulting in that materials partly adhere to the machined surface and form the material piling zone. As the depth of cut and the feed per tooth increase, the plastic flow of materials is strengthened and the machined surface becomes rougher. However, as the cutting speed increases, the plastic flow of materials is weakened and the milled surface becomes smoother. The cutting parameters (e.g. cutting speed, feed per tooth and depth of cut) influencing the surface roughness are analyzed. It can be concluded that the roughness of the machined surface formed by the end cutting edge is less than that by the cylindrical cutting edge when a cylindrical flat-end mill tool is used for milling. The proposed research provides the typical topography features of machined surface of the anti-rust aluminum alloy AlMn1Cu in high speed milling.

Analogy between spin glasses and Yang--Mills fluids

International Nuclear Information System (INIS)

Holm, D.D.; Kupershmidt, B.A.

1988-01-01

A dictionary of correspondence is established between the dynamical variables for spin-glass fluid and Yang-Mills plasma. The Lie-algebraic interpretation of these variables is presented for the two theories. The noncanonical Poisson bracket for the Hamiltonian dynamics of an ideal spin glass is shown to be identical to that for the dynamics of a Yang--Mills fluid plasma, although the Hamiltonians differ for the two theories. This Poisson bracket is associated to the dual space of an infinite-dimensional Lie algebra of semidirect-product type

Introduction to instantons in Yang-Mills theory

International Nuclear Information System (INIS)

Pak, N.K.

1980-02-01

The Yang-Mills theory is outlined; the classical formalism is discussed first, and then the difficulties related to gauge invariance in the canonical quantization of the theory are taken up. Next, the task of finding and studying Euclidean gauge field configurations of finite action as solutions to the equation of motion is addressed. It is found that configurations which contribute the most in the semi-classical approximation are those which minimize the action. The question of a lower bound for the Euclidean action is considered. Properties of topological charge and the behavior of topological charge under gauge transformation are discussed. Then instanton solutions to the field equations are produced. Finally, the physical interpretation of the instanton is considered. It is found that the instanton, the Euclidean gauge field configuration which minimizes the action, induces tunneling among the infinitely degenerate vacua of the Yang-Mills theory by lifting the degeneracy and creating new distinct inequivalent (invariant under topologically nontrivial gauge transformations) vacua labelled by a superselection index theta. The angle theta is shown not to be a gauge artifact. In conclusion, the tunneling Hamiltonian and effective Lagrangian for the Yang-Mills theory are discussed

Transforming from paramagnetism to room temperature ferromagnetism in CuO by ball milling

Directory of Open Access Journals (Sweden)

Daqiang Gao

2011-12-01

Full Text Available In this work, we experimentally demonstrate that it is possible to induce ferromagnetism in CuO by ball milling without any ferromagnetic dopant. The magnetic measurements indicate that paramagnetic CuO is driven to the ferromagnetic state at room temperature by ball milling gradually. The saturation magnetization of the milled powders is found to increase with expanding the milling time and then decrease by annealing under atmosphere. The fitted X-ray photoelectron spectroscopy results indicate that the observed induction and weaken of the ferromagnetism shows close relationship with the valence charged oxygen vacancies (Cu1+-VO in CuO.

Highly anisotropic SmCo5 nanoflakes by surfactant-assisted ball milling at low temperature

International Nuclear Information System (INIS)

Liu, Lidong; Zhang, Songlin; Zhang, Jian; Ping Liu, J.; Xia, Weixing; Du, Juan; Yan, Aru; Yi, Jianhong; Li, Wei; Guo, Zhaohui

2015-01-01

Surfactant-assisted ball milling (SABM) has been shown to be a promising method for preparing rare earth-transition metal (RE-TM) nanoflakes and nanoparticles. In this work, we prepared SmCo 5 nanoflakes by SABM at low temperature, and 2-methyl pentane and trioctylamine were specially selected as solvent and surfactant, respectively, due to their low melting points. The effects of milling temperature on the morphology, microstructure and magnetic performance of SmCo 5 nanoflakes were investigated systematically. Comparing with the samples milled at room temperature, the SmCo 5 nanoflakes prepared at low temperature displayed more homogeneous morphology and lower oxygen content. Remarkably, better crystallinity, better grain alignment and larger remanence ratio were shown in the samples milled at low temperature, which resulted from the distinct microstructure caused by low milling temperature. The differences in structural evolution between the SmCo 5 nanoflakes milled at room temperature and low temperature, including the formation of nanocrystalline, grain boundary sliding, grain rotation, et al., were discussed. It was found that lowering the temperature of SABM was a powerful method for the fabrication of RE-TM nanoflakes, which showed better hard magnetic properties and lower oxygen content. This was important for the preparation of high-performance sintered magnets, bonded magnets and nanocomposite magnets. - Highlights: • We prepare SmCo 5 nanoflakes by surfactant-assisted ball milling at low temperature. • Better grain alignment and higher remanence ratio are achieved. • The oxygen content is reduced by lowering the milling temperature. • A distinct microstructural evolution caused by low milling temperature is clarified

76 FR 2409 - Proclaiming Certain Lands, Golf Course Acquisition, as an Addition to the Bay Mills Indian...

Science.gov (United States)