The variability of wood density and compression strength of Norway spruce

Czech Academy of Sciences Publication Activity Database

Horáček, Petr; Fajstavr, Marek; Stojanović, Marko

2017-01-01

Roč. 10, 1-2 (2017), s. 17-26 ISSN 1803-2451 R&D Projects: GA MŠk(CZ) LO1415 Institutional support: RVO:86652079 Keywords : Norway spruce * wood density * compression strength * variability Subject RIV: GK - Forestry OBOR OECD: Forestry

A 3D multilevel model of damage and strength of wood: Analysis of microstructural effects

DEFF Research Database (Denmark)

Qing, Hai; Mishnaevsky, Leon

2011-01-01

A 3D hierarchical computational model of damage and strength of wood is developed. The model takes into account the four scale microstructures of wood, including the microfibril reinforced structure at nanoscale, multilayered cell walls at microscale, hexagon-shape-tube cellular structure...

Effects of tanalith-e impregnation substance on bending strengths and modulus of elasticity in bending of some wood types

Directory of Open Access Journals (Sweden)

Hakan Keskin

2016-04-01

Full Text Available The aim of this study was to investigate the effects of impregnation with Tanalith-E on the bending strengths and modulus of elasticity in bending of some wood types. The test samples prepared from beech, oak, walnut, poplar, ash and pine wood materials - that are of common use in the forest products industry of TURKEY - according to TS 345, were treated with according to ASTM D 1413-76 substantially. Un-impregnated samples according to impregnated wood materials, the bending strengths in beech to 6.83%, 5.12% in ash, 5.93% in pine, the elasticity module values to 7.15% in oak and ash, at a rate of 6.58% in the higher were found. The highest values of bending strengths and modulus of elasticity in bending were obtained in beech and ash woods impregnated with Tanalith-E, whereas the lowest values were obtained in the poplar wood.

On the influence of crack closure on strength estimates of wood

DEFF Research Database (Denmark)

Nielsen, Lauge Fuglsang

2004-01-01

Three well-known duration of load models (Gerhard, Barrett/Foschi, DVM) are considered in this note with respect to their ability to predict lifetime of wood subjected to harmonically varying loads. The result obtained is that they practically predict the same lifetime—which for low frequency...... in metals).It is suggested that any of the simple models can be used in practice when low frequency load variations are considered. The DVM model, however, should be preferred because of its ability to predict residual strength, and because of its ‘build in’ flexibility with respect to wood quality...

Strength loss in decayed wood

Science.gov (United States)

Rebecca E. Ibach; Patricia K. Lebow

2014-01-01

Wood is a durable engineering material when used in an appropriate manner, but it is susceptible to biological decay when a log, sawn product, or final product is not stored, handled, or designed properly. Even before the biological decay of wood becomes visually apparent, the decay can cause the wood to become structurally unsound. The progression of decay to that...

The Effect of Heat Treatment on the Pull-off Strength of Optionally Varnished Surfaces of Five Wood Materials

Directory of Open Access Journals (Sweden)

Musa Atar

2015-09-01

Full Text Available This study investigated the effects of heat treatment, following optional treatment with synthetic, water-based, and alkyd varnishes, on the pull-off strength of wooden materials sampled from oriental beech (Fagus orientalis L., oak (Quercus petraea Liebl., black poplar (Populus nigra L., pine (Pinus sylvestris L., and fir (Abies bornmulleriana M.. The test samples were subjected to heat treatment at temperatures of 165 °C and 175 °C for periods of 2 and 4 h with a total of 4 variations. With respect to the wood type, the samples of beech wood yielded the highest results for pull-off strength, while fir wood yielded the lowest. With respect to the varnish types, the highest pull-off strength was found in the samples of synthetic varnished beech (5,452 with a 37.2% improvement at 175 °C heat treatment for 4 h, while the lowest results were obtained in the samples of fir (0.991 with a 48.5% decrease at 175 °C heat treatment for 4 h. In conclusion, heat treatment significantly decreased the pull-off strength of the woods.

Investigation on the Scratch Strength of Clear Paints Used in Furniture Industries on the Wood Species Beech, Elm, Alder and Spruce

Directory of Open Access Journals (Sweden)

Mohammad Ghofrani

2014-05-01

Full Text Available In This research, the scratch strength (Cross-Cut Test of clear paints (nitrocellulose lacquers and acid catalyst lacquers of wood species Beech, Elm, Alder and spruce were studied as a function of moisture content (MC of the samples. For this purpose, lumbers (550×110×12 mm were cut from sapwood in tangential surfaces and were air dried for one month according to wood drying procedures. Then, for pre-conditioning of moisture content, at the levels of 8%, 12% and 15%, the samples were placed in three clima rooms. Then, finish applied and strength tests were performed. The results revealed that for acid catalyst lacquers the highest scratch strength (10.4% belongs to Elm wood with 8% moisture content, and the lowest scratch strength (53.6% belongs to Spruce wood with nitrocellulose lacquers having 15% moisture content.

Analysis of lifetime and residual strength of wood

DEFF Research Database (Denmark)

Nielsen, Lauge Fuglsang

1997-01-01

The present paper is thought of as a working paper for the CTBA-seminar on Thematic network in the field for reliability based design of timber structures, Topic: Numerical methods for structural analysis. It is preliminary and quite informal in its structure. The intention is to present some wood...... technological problems which can be solved with respect to lifetime and residual strength by the so-called DVM-theory (Damaged Viscoelastic Material). The outlines of the paper is straight on: Expressions are presented by which the analysis is made. then some examples are considered with solutions presented...

Production of plastified wood with stronger static bending strength means of polymerization induced by gamma radiation

International Nuclear Information System (INIS)

Silva Filho, Elias

1999-01-01

The use of gamma radiation to obtain wood-polymer composites is one of the applications of radiation that presents the most commercial interest. The process, denominated radiopolymerization, comprises the impregnation of monomers into the completely dried wood followed by exposure to gamma radiation to induce polymerization of the impregnated monomers. I this context, the present work aimed the application of this process to seven kinds of wood existing in the brazilian forests. The considered monomer is styrene and the gamma source is Cobalt-60. The obtained wood-polystyrene composites were found to have stronger static bending strength. (author)

Wood construction under cold climate

DEFF Research Database (Denmark)

Wang, Xiaodong; Hagman, Olle; Sundqvist, Bror

2014-01-01

As wood constructions increasingly use engineered wood products worldwide, concerns arise about the integrity of the wood and adhesives system. The glueline stability is a crucial issue for engineered wood application, especially under cold climate. In this study, Norway spruce (Picea abies...... affected shear strength of wood joints. As temperature decreased, the shear strength decreased. PUR resin resulted in the strongest shear strength at all temperatures tested. MF resin responded to temperature changes in a similar ways as the PUR resin. The shear strength of wood joints with EPI resins...... specimens need to be tested in further work to more completely present the issue. The EN 301 and EN 302 may need to be specified based on wood species....

COMPARISON BETWEEN TEST METHODS TO DETERMINE WOOD EMBEDMENT STRENGTH PARALLEL TO THE GRAIN

Directory of Open Access Journals (Sweden)

Diego Henrique de Almeida

Full Text Available ABSTRACT This study compares the test methods according to the ABNT NBR 7190:1997, EN 383:2007, ASTM D5764:2007, EUROCODE 5:2004, NDS:2001 standards in order to provide support to establish a new test method for determining the embedment strength of wood parallel to the grain. Parallel-to-grain tests were carried out for six wood species (Schizolobium amazonicum; Pinus elliottii; Pinus oocarpa; Hymenaea spp.; Lyptus(r: hybrid Eucalyptus grandis and Eucalyptus urophylla, and Goupia glabra using four diameters (8 mm, 10 mm, 12 mm and 16 mm for the metal pin fasteners (bolts. The experimental results obtained according to the EN 383:2007 standard were closer to the specific values for the metal-dowel connections design used by ABNT NBR 7190:1997, which are considered equal compression parallel to the grain. The use of maximum embedment force or the force causing displacement of 5 mm between the bolt and the test-piece as criteria for determining embedment strength for EN 383:2007 appears to be more appropriate than the criteria used by the Brazilian and American Standards.

Wood frame systems for wood homes

Directory of Open Access Journals (Sweden)

Julio Cesar Molina

2010-12-01

Full Text Available The use of constructive systems that combine strength, speed, with competitive differential techniques and mainly, compromising with the environment, is becoming more popular in Brazil. The constructive system in wood frame for houses of up to five stories is very interesting, because it is a light system, structured in reforested treated wood which allows the combination of several materials, besides allowing speed in the construction and total control of the expenses already in the project phase for being industrialized. The structural behavior of the wood frame is superior to the structural masonry in strength, thermal and acoustic comfort. However, in Brazil, the wood frame is still little known and used, due to lack of technical knowledge about the system, prejudice associated the bad use of the wood as construction material, or still, in some cases, lack of normalization. The aim of this manuscript consists of presenting the main technical characteristics and advantages of the constructive system in wood frame homes, approaching the main stages of the constructive process through examples, showing the materials used in the construction, in addition the main international normative recommendations of the project. Thus, this manuscript also hopes to contribute to the popularization of the wood frame system in Brazil, since it is a competitive, fast and ecologically correct system. Moreover, nowadays, an enormous effort of the technical, commercial and industrial section has been accomplished for the development of this system in the country.

Influence of xylem ray integrity and degree of polymerization on bending strength of beech wood decayed by Pleurotus ostreatus and Trametes versicolor

Science.gov (United States)

Ehsan Bari; Reza Oladi; Olaf Schmidt; Carol A. Clausen; Katie Ohno; Darrel D. Nicholas; Mehrdad Ghodskhah Daryaei; Maryam Karim

2015-01-01

The scope of this research was to evaluate the influence of xylem ray (XR) and degree of polymerization (DP) of holocellulose in Oriental beech wood (Fagus orientalis Lipsky.) on impact bending strength against two white-rot fungi. Beech wood specimens, exposed to Pleurotus ostreatus and Trametes versicolor, were evaluated for...

Influence of Welding Time on Tensile-Shear Strength of Linear Friction Welded Birch (Betula pendula L. Wood

Directory of Open Access Journals (Sweden)

Jussi Ruponen

2015-04-01

Full Text Available The purpose of this work was to determine the optimal welding time for linear friction welding of birch (Betula pendula L. wood while keeping the other parameters constant and at similar levels compared to other species in a similar density range. Specimens with dimensions of 20 × 5 × 150 mm3 were welded together, and the influence of welding time (2.5, 3.0, 3.5, and 4.0 s on the mechanical properties of the specimens was determined. The studies included a tensile-shear strength test as well as visual estimation of wood failure percentage (WFP. Additionally, X-ray microtomographic imaging was used to investigate and characterise the bond line properties as a non-destructive testing method. The highest mean tensile-shear strength, 7.9 MPa, was reached with a welding time of 3.5 s. Generally, all four result groups showed high, yet decreasing proportional standard deviations as the welding time increased. X-ray microtomographic images and analysis express the heterogeneity of the weld line clearly as well. According to the averaged group-wise results, WFP and tensile-shear strength correlated positively with an R2 of 0.93. An extrapolation of WFP to 65% totals a tensile-shear strength of 10.6 MPa, corresponding to four common adhesive bonds determined for beech.

PHYSICAL AND STRENGTH PROPERTIES OF BRICKS PRODUCED FROM PORTLAND CEMENT AND SAW DUST OF DANIELIA OLIVERII WOOD

Directory of Open Access Journals (Sweden)

David Oriabure EKHUEMELO

2016-12-01

Full Text Available This study investigated the use of sawdust as partial replacement for sand in wood-concrete hollow blocks. Sharp sand, ordinary Portland cement (binder and sawdust were used as raw materials. Sawdust was treated by boiling then sieved after drying using British Standard sieve of 3.35mm to remove sticky wood capable of causing pores. The quantities of sawdust used were 0%, 5%, 10%, 15% and 20%. A mixing proportion of 1:8 cement sand ratio, moulding machine with single 6” (450mm x 225mm x 150mm mould and vibrated with 5.0KW power machine for adequate compaction were used. Wood-concrete block was cured for 28 days. The blocks produced were tested for compressive strength and water absorption. The results showed that mean compressive strength of 100% sand was 2.81N/mm2 followed by 95% sand and 5% sawdust replacement with 1.58N/mm2 ; 90% Sand and 10% sawdust replacement with 0.55N/mm2 ; 85% sand and 15% sawdust replacement with 0.43 N/mm2 and 80% sand 20% sawdust replacement with 0.24N/mm2 . The result further showed that as the percentage of sawdust increased, the compressive strength decreased. At 28 days, the compressive strength of blocks with 5% SD replacement satisfied meets Ghana Building Code for non- load bearing walls. The results also reveals that blocks with 80% sand 20% sawdust replacement level has the highest water absorption (23.72% followed by 85% Sand and 15% sawdust replacement (20.40%; 90% sand and 10% sawdust replacement (18.0%; 95% sand and 5% sawdust replacement (12.12% and 100% sand and 0% sawdust replacement (11.43%. It was concluded that 5% sawdust (8kg replacement and cured 28 days could be used for non-load bearing walls. It was recommended that further research should be carried out to evaluate sawdust replacement level within the range of 1-4% to ascertain results that could be used for various other purposes.

Physical and Strength Properties of Bricks Produced from Portland Cement and Saw Dust of Danielia Oliverii Wood

Directory of Open Access Journals (Sweden)

David Oriabure EKHUEMELO

2016-12-01

Full Text Available This study investigated the use of sawdust as partial replacement for sand in wood-concrete hollow blocks. Sharp sand, ordinary Portland cement (binder and sawdust were used as raw materials. Sawdust was treated by boiling then sieved after drying using British Standard sieve of 3.35mm to remove sticky wood capable of causing pores. The quantities of sawdust used were 0%, 5%, 10%, 15% and 20%. A mixing proportion of 1:8 cement sand ratio, moulding machine with single 6” (450mm x 225mm x 150mm mould and vibrated with 5.0KW power machine for adequate compaction were used. Wood-concrete block was cured for 28 days. The blocks produced were tested for compressive strength and water absorption. The results showed that mean compressive strength of 100% sand was 2.81N/mm2 followed by 95% sand and 5% sawdust replacement with 1.58N/mm2 ; 90% Sand and 10% sawdust replacement with 0.55N/mm2 ; 85% sand and 15% sawdust replacement with 0.43 N/mm2 and 80% sand 20% sawdust replacement with 0.24N/mm2 . The result further showed that as the percentage of sawdust increased, the compressive strength decreased. At 28 days, the compressive strength of blocks with 5% SD replacement satisfied meets Ghana Building Code for non- load bearing walls. The results also reveals that blocks with 80% sand 20% sawdust replacement level has the highest water absorption (23.72% followed by 85% Sand and 15% sawdust replacement (20.40%; 90% sand and 10% sawdust replacement (18.0%; 95% sand and 5% sawdust replacement (12.12% and 100% sand and 0% sawdust replacement (11.43%. It was concluded that 5% sawdust (8kg replacement and cured 28 days could be used for non-load bearing walls. It was recommended that further research should be carried out to evaluate sawdust replacement level within the range of 1-4% to ascertain results that could be used for various other purposes.

Radiation processed composite materials of wood and elastic polyester resins

International Nuclear Information System (INIS)

Tapolcai, I.; Czvikovszky, T.

1983-01-01

The radiation polymerization of multifunctional unsaturated polyester-monomer mixtures in wood forms interpenetrating network system. The mechanical resistance (compression, abrasion, hardness, etc.) of these composite materials are generally well over the original wood, however the impact strength is almost the same or even reduced, in comparison to the wood itself. An attempt is made using elastic polyester resins to produced wood-polyester composite materials with improved modulus of elasticity and impact properties. For the impregnation of European beech wood two types of elastic unsaturated polyester resins were used. The exothermic effect of radiation copolymerization of these resins in wood has been measured and the dose rate effects as well as hardening dose was determined. Felxural strength and impact properties were examined. Elastic unsaturated polyester resins improved the impact strength of wood composite materials. (author)

Detection of wood failure by image processing method: influence of algorithm, adhesive and wood species

Science.gov (United States)

Lanying Lin; Sheng He; Feng Fu; Xiping Wang

2015-01-01

Wood failure percentage (WFP) is an important index for evaluating the bond strength of plywood. Currently, the method used for detecting WFP is visual inspection, which lacks efficiency. In order to improve it, image processing methods are applied to wood failure detection. The present study used thresholding and K-means clustering algorithms in wood failure detection...

Long term durability of wood-plastic composites made with chemically modified wood

Science.gov (United States)

Rebecca E. Ibach; Craig M. Clemons

2017-01-01

Wood-plastic composites (WPCs) have slower moisture sorption than solid wood, but over time moisture can impact the strength, stiffness, and decay of the composite. These changes will become increasingly important if WPCs are used in more challenging environments such as in ground-contact applications. There are several options for mitigating the moisture sorption of...

BEHAVIOR OF GLUED JOINTS OF EUCALYPTUS sp. SAWN WOOD

Directory of Open Access Journals (Sweden)

Octávio Barbosa Plaster

2008-09-01

Full Text Available This research evaluated eucalypt wood adhesion capacity. The material evaluated was a commercial sawn wood composed by a blend of species of the genus Eucalyptus. The adhesives used were resorcinol-formaldehyde and polyvinila acetate (PVAc. The wood was segregated in three density with 0% of moisture content: class 1; 2 and 3 that, when combined (class1 x class1; 2x2; 3x3; 1x2; 1x3; 2x3 resulted in six treatments. The performance of the adhesion was evaluated by the shear strength to parallel compression and by wood failure in the glue line. The obtained results allowed to conclude that the adhesion of the combinations of wood/adhesive presented satisfactory performance. The average shear strength of the joints were shown equivalent to the shear strength of the solid wood with similar performance of adhesion in the two adhesives. In general, resorcinol-formaldheyde adhesive presented higher values (74.41% for wood failure in the joints, but similar to all treatments. The adhesion of samples of higher density presented lower performance probably when only the values of wood failure are considered. The values for the strength of glued joints, in general, were similar when analyzed the results achieved with the resorcinol-formaldehyde adhesive- base 140,56 Kgf/cm2. To polyvinila acetate the values of wood failure decrease when the density increase (65.94%, but the resistance in the glue line was positively affected (140.25 Kgf/cm2. In general, the density influenced the adhesion of the joints for the employed adhesives.

Biomaterial based novel polyurethane adhesives for wood to wood and metal to metal bonding

Directory of Open Access Journals (Sweden)

Mitesh Ramanlal Patel

2009-01-01

Full Text Available Polyurethane adhesives made from synthetic chemicals are non-biodegradable, costly and difficult to find raw materials from local market. To avoid solid pollution problem, cost effectiveness and easy availability of raw materials, biomaterials based polyurethane adhesives are used in current industrial interest. Direct use of castor oil in polyurethane adhesive gives limited hardness. Modification on active sites of castor oil to utilize double bond of unsaturated fatty acid and carboxyl group yields new modified or activated polyols, which can be utilized for polyurethane adhesive formulation. In view of this, we have synthesized polyurethane adhesives from polyester polyols, castor oil based polyols and epoxy based polyols with Isocyanate adducts based on castor oil and trimethylolpropane. To study the effects of polyurethane adhesive strength (i.e. lap shear strength on wood-to-wood and metal-to-metal bonding through various types of polyols, cross-linking density, isocyanate adducts and also to compare adhesive strength between wood to wood and metal to metal surface. These polyols and polyurethanes were characterized through GPC, NMR and IR-spectroscopy, gel and surface drying time. Thermal stability of PU adhesives was determined under the effect of cross-linking density (NCO/OH ratio. The NCO/OH ratio (1.5 was optimized for adhesives as the higher NCO/OH ratio (2.0 increasing cross-linking density and decreases adhesion. Lower NCO/OH ratio (1.0 provideslow cross-linking density and low strength of adhesives.

Properties of Hungarian oak(quercus conferta Kit. wood from the Hilandar Monastery forest

Directory of Open Access Journals (Sweden)

Popović Zdravko

2007-01-01

Full Text Available This paper presents the study results of the basic physical and strength properties of Hungarian oak (Quercus conferta Kit. wood from the Kakovo Monastery forests of Hilandar Monastery in Greece. Wood properties were analyzed in detail, as an indispensable proof of wood quality and its use for joinery, interiors and wooden floors. The basic physical properties of wood (moisture content at the time of tree felling, density and volume porosity and the basic strength properties (compressive strength, bending strength and module of elasticity were researched. The results are presented in Tables and in Diagrams with statistical parameters and compared to the literature data. The correlation of the study properties of wood was also analyzed.

Justification of the Production Process of Pressed Wood and Study of its Properties

Science.gov (United States)

Polilov, A. N.; Dornyak, O. R.; Shamaev, V. A.; Rumachik, M. M.

2018-05-01

Results of a numerical analysis of the stress-strain state of wood during its pressing in different symmetry directions of the anisotropic material are presented. It is shown that the anisotropy of mechanical properties of wood is an important factor determining both the structural characteristics of the porous system and its strength. A mathematical modeling of the process of pressing wood as a three-phase anisotropic rheologically complex capillary-porous system allows one to predict parameters of the resulting wood composite. The compressed wood obtained by the production modes developed has a tensile strength eight times greater than that of the natural one, which is comparable to the strength of the St3 steel, but its specific strength is higher than that of the St45 steel. Compression and impregnation of softwood species with an aqueous solution of carbamide allows one to harden them. This kind of treatment endows the wood with enhanced strength characteristics comparable to the characteristics of the St3 steel. The special features of tensile tests used to estimate the elastic modulus and strength characteristics of such materials are considered. Data obtained by different testing methods are correlated, and characteristics of the strengthened wood and some brends of steel are compared.

Preservation of beech and spruce wood by allyl alcohol-based copolymers

International Nuclear Information System (INIS)

Solpan, Dilek; Gueven, Olgun

1999-01-01

Allyl alcohol (AA), acrylonitrile (AN), methyl methacrylate (MMA), monomers and monomer mixtures AA+AN, AA+MMA were used to conserve and consolidate Beech and Spruce. After impregnation, copolymerisation and polymerisation were accomplished by gamma irradiation. The fine structure of wood+polymer(copolymer) composites was investigated by Scanning Electron Microscopy (SEM). It was observed that copolymer obtained from AA+MMA monomer mixture showed the optimum compatibility. The compressional strength and Brinell Hardness Numbers determined for untreated and treated wood samples indicated that the mechanical strength of wood+copolymer composites was increased. It was found that the mechanical strength of the wood samples containing the AA+MMA copolymer was higher than the others. In the presence of P(AA/MMA), at highest conversion, the compressive strength perpendicular to the fibres in Beech and Spruce increased approximately 100 times. The water uptake capacity of wood+copolymer composites was observed to decrease by more than 50% relative to the original samples, and biodegradation did not take place

Studies of properties of rubber wood with impregnation of polymer

Indian Academy of Sciences (India)

Impregnation of rubber wood has been carried out under different conditions by using styrene as grafting monomer and glycidyl methacrylate (GMA) as crosslinker. Properties such as dimensional stability, water absorption, hardness, tensile strength, flexural strength, etc of the impregnated wood have been checked and ...

Adhesion quality of glued joints from different commercial wood species

Directory of Open Access Journals (Sweden)

Alexandre Miguel do Nascimento

2013-12-01

Full Text Available The objective of this study was to determine the effect of wood density, adhesive type and gluing pressure on the shear strength of glued joints of fourteen commercial wood species. Wood pieces were classified in three density classes (Class 1: less than 0.55 g cm-3; Class 2: from 0.55 to 0.75 g cm-3; and Class 3: greater than 0.75 g cm-3 and joints bonded with two adhesives: polyvinyl acetate (PVA and urea-formaldehyde (UF, under two different pressures: 6 and 12 kgf cm-2. Glued joints bonded with PVA adhesive presented higher shear strength than those bonded with UF adhesive. For percentage of wood failure, the PVA adhesive had the best performance, however, only Classes 1 and 2 reached the values required by ASTM 3110 standard. Glued joints from Class 3, bonded with UF adhesive, did not reach the values of solid wood. The gluing pressure of 12 kgf cm-2 was more efficient for Class 3, for both shear strength and percentage of wood failure.

Improvement in Wood Bonding Strength of Poly (Vinyl Acetate-Butyl Acrylate Emulsion by Controlling the Amount of Redox Initiator

Directory of Open Access Journals (Sweden)

Yun Zhang

2018-01-01

Full Text Available Polyvinyl acetate emulsion adhesive has been widely used due to its good bonding performance and environmentally friendly properties. Indeed, the bonding performance can be further improved by copolymerizing with other monomers. In this study, the effect of the adjunction of redox initiator (hydrogen peroxide–tartaric acid, H2O2–TA on the properties of the poly (vinyl acetate-butyl acrylate (P (VAc–BA emulsion adhesive was investigated. With increasing dosage, the reaction became more complete and the obtained film was more compact, as identified via SEM. The core-shell structure of the emulsion particles was confirmed via TEM. Results indicate that while the initiator content increased from 0.5 to 1.0%, a clearer core-shell structure was obtained and the bonding strength of the plywood improved from 2.34 to 2.97 MPa. With the further incorporation of H2O2–TA (i.e., 1.5%, the bonding performance deteriorated. The optimum wood bonding strength (2.97 MPa of the prepared P (VAc-BA emulsion adhesive was even better than that (2.55 MPa of a commercial PVAc emulsion adhesive, suggesting its potential application for the wood industry.

Measuring wood specific gravity, correctly

Science.gov (United States)

G. Bruce Williamson; Michael C. Wiemann

2010-01-01

The specific gravity (SG) of wood is a measure of the amount of structural material a tree species allocates to support and strength. In recent years, wood specific gravity, traditionally a forester’s variable, has become the domain of ecologists exploring the universality of plant functional traits and conservationists estimating global carbon stocks. While these...

Selected mechanical properties of modified beech wood

Directory of Open Access Journals (Sweden)

Jiří Holan

2008-01-01

Full Text Available This thesis deals with an examination of mechanical properties of ammonia treated beach wood with a trademark Lignamon. For determination mechanical properties were used procedures especially based on ČSN. From the results is noticeable increased density of wood by 22% in comparison with untreated beach wood, which makes considerable increase of the most mechanical wood properties. Considering failure strength was raised by 32% and modulus of elasticity was raised at average about 46%.

Still rethinking the value of high wood density.

Science.gov (United States)

Larjavaara, Markku; Muller-Landau, Helene C

2012-01-01

In a previous paper, we questioned the traditional interpretation of the advantages and disadvantages of high wood density (Functional Ecology 24: 701-705). Niklas and Spatz (American Journal of Botany 97: 1587-1594) challenged the biomechanical relevance of studying properties of dry wood, including dry wood density, and stated that we erred in our claims regarding scaling. We first present the full derivation of our previous claims regarding scaling. We then examine how the fresh modulus of rupture and the elastic modulus scale with dry wood density and compare these scaling relationships with those for dry mechanical properties, using almost exactly the same data set analyzed by Niklas and Spatz. The derivation shows that given our assumptions that the modulus of rupture and elastic modulus are both proportional to wood density, the resistance to bending is inversely proportional to wood density and strength is inversely proportional with the square root of wood density, exactly as we previously claimed. The analyses show that the elastic modulus of fresh wood scales proportionally with wood density (exponent 1.05, 95% CI 0.90-1.11) but that the modulus of rupture of fresh wood does not, scaling instead with the 1.25 power of wood density (CI 1.18-1.31). The deviation from proportional scaling for modulus of rupture is so small that our central conclusion remains correct: for a given construction cost, trees with lower wood density have higher strength and higher resistance to bending.

Withdrawal Strength and Bending Yield Strength of Stainless Steel Nails

Science.gov (United States)

Douglas R. Rammer; Samuel L. Zelinka

2015-01-01

It has been well established that stainless steel nails have superior corrosion performance compared to carbon steel or galvanized nails in treated wood; however, their mechanical fastening behavior is unknown. In this paper, the performance of stainless steel nails is examined with respect to two important properties used in wood connection design: withdrawal strength...

Preparation and testing of plant seed meal-based wood adhesives.

Science.gov (United States)

He, Zhongqi; Chapital, Dorselyn C

2015-03-05

Recently, the interest in plant seed meal-based products as wood adhesives has steadily increased, as these plant raw materials are considered renewable and environment-friendly. These natural products may serve as alternatives to petroleum-based adhesives to ease environmental and sustainability concerns. This work demonstrates the preparation and testing of the plant seed-based wood adhesives using cottonseed and soy meal as raw materials. In addition to untreated meals, water washed meals and protein isolates are prepared and tested. Adhesive slurries are prepared by mixing a freeze-dried meal product with deionized water (3:25 w/w) for 2 hr. Each adhesive preparation is applied to one end of 2 wood veneer strips using a brush. The tacky adhesive coated areas of the wood veneer strips are lapped and glued by hot-pressing. Adhesive strength is reported as the shear strength of the bonded wood specimen at break. Water resistance of the adhesives is measured by the change in shear strength of the bonded wood specimens at break after water soaking. This protocol allows one to assess plant seed-based agricultural products as suitable candidates for substitution of synthetic-based wood adhesives. Adjustments to the adhesive formulation with or without additives and bonding conditions could optimize their adhesive properties for various practical applications.

Elucidating How Wood Adhesives Bond to Wood Cell Walls using High-Resolution Solution-State NMR Spectroscopy

Science.gov (United States)

Daniel J. Yelle

2013-01-01

Some extensively used wood adhesives, such as pMDI (polymeric methylene diphenyl diisocyanate) and PF (phenol formaldehyde) have shown excellent adhesion properties with wood. However, distinguishing whether the strength is due to physical bonds (i.e., van der Waals, London, or hydrogen bond forces) or covalent bonds between the adherend and the adhesive is not fully...

Effects of Heat-Treated Wood Particles on the Physico-Mechanical Properties and Extended Creep Behavior of Wood/Recycled-HDPE Composites Using the Time–Temperature Superposition Principle

Directory of Open Access Journals (Sweden)

Teng-Chun Yang

2017-03-01

Full Text Available This study investigated the effectiveness of heat-treated wood particles for improving the physico-mechanical properties and creep performance of wood/recycled-HDPE composites. The results reveal that the composites with heat-treated wood particles had significantly decreased moisture content, water absorption, and thickness swelling, while no improvements of the flexural properties or the wood screw holding strength were observed, except for the internal bond strength. Additionally, creep tests were conducted at a series of elevated temperatures using the time–temperature superposition principle (TTSP, and the TTSP-predicted creep compliance curves fit well with the experimental data. The creep resistance values of composites with heat-treated wood particles were greater than those having untreated wood particles due to the hydrophobic character of the treated wood particles and improved interfacial compatibility between the wood particles and polymer matrix. At a reference temperature of 20 °C, the improvement of creep resistance (ICR of composites with heat-treated wood particles reached approximately 30% over a 30-year period, and it increased significantly with increasing reference temperature.

Effects of Heat-Treated Wood Particles on the Physico-Mechanical Properties and Extended Creep Behavior of Wood/Recycled-HDPE Composites Using the Time–Temperature Superposition Principle

Science.gov (United States)

Yang, Teng-Chun; Chien, Yi-Chi; Wu, Tung-Lin; Hung, Ke-Chang; Wu, Jyh-Horng

2017-01-01

This study investigated the effectiveness of heat-treated wood particles for improving the physico-mechanical properties and creep performance of wood/recycled-HDPE composites. The results reveal that the composites with heat-treated wood particles had significantly decreased moisture content, water absorption, and thickness swelling, while no improvements of the flexural properties or the wood screw holding strength were observed, except for the internal bond strength. Additionally, creep tests were conducted at a series of elevated temperatures using the time–temperature superposition principle (TTSP), and the TTSP-predicted creep compliance curves fit well with the experimental data. The creep resistance values of composites with heat-treated wood particles were greater than those having untreated wood particles due to the hydrophobic character of the treated wood particles and improved interfacial compatibility between the wood particles and polymer matrix. At a reference temperature of 20 °C, the improvement of creep resistance (ICR) of composites with heat-treated wood particles reached approximately 30% over a 30-year period, and it increased significantly with increasing reference temperature. PMID:28772726

Lignonsulfonate-phenolformaldehyrde adhesive: a potential binder for wood panel industries

International Nuclear Information System (INIS)

Akhtar, T.; Lutfullah, G.; Ullah, Z.

2011-01-01

Spent sulfite liquor (SSL) was obtained from a paper mill based on grassy pulp material (bagasse, kaigrass and wheat straws). Lignosulfonate (LS) was isolated from SSL by polymerization reaction, initiated with concentrated hydrochloric acid. Different adhesives were prepared by gradual replacement of phenol by LS in phenol-formaldehyde (PF) resole resin. The strength of these resins was evaluated by glue block shear test in two wood species, in both dry and wet states. Maximum shear strength and wood failure was obtained by 20% addition of lignosulfonate to PF resin. No significant difference was observed in shear strength and wood failure of the two wood species in dry and wet states indicating that the resin obtained is waterproof. The results obtained from this study were compared with different commercial glues. Our results were found better than these glues event at a ratio 50: 50 of PF to lignosulfonate. (author)

Processing bulk natural wood into a high-performance structural material

Science.gov (United States)

Song, Jianwei; Chen, Chaoji; Zhu, Shuze; Zhu, Mingwei; Dai, Jiaqi; Ray, Upamanyu; Li, Yiju; Kuang, Yudi; Li, Yongfeng; Quispe, Nelson; Yao, Yonggang; Gong, Amy; Leiste, Ulrich H.; Bruck, Hugh A.; Zhu, J. Y.; Vellore, Azhar; Li, Heng; Minus, Marilyn L.; Jia, Zheng; Martini, Ashlie; Li, Teng; Hu, Liangbing

2018-02-01

Synthetic structural materials with exceptional mechanical performance suffer from either large weight and adverse environmental impact (for example, steels and alloys) or complex manufacturing processes and thus high cost (for example, polymer-based and biomimetic composites). Natural wood is a low-cost and abundant material and has been used for millennia as a structural material for building and furniture construction. However, the mechanical performance of natural wood (its strength and toughness) is unsatisfactory for many advanced engineering structures and applications. Pre-treatment with steam, heat, ammonia or cold rolling followed by densification has led to the enhanced mechanical performance of natural wood. However, the existing methods result in incomplete densification and lack dimensional stability, particularly in response to humid environments, and wood treated in these ways can expand and weaken. Here we report a simple and effective strategy to transform bulk natural wood directly into a high-performance structural material with a more than tenfold increase in strength, toughness and ballistic resistance and with greater dimensional stability. Our two-step process involves the partial removal of lignin and hemicellulose from the natural wood via a boiling process in an aqueous mixture of NaOH and Na2SO3 followed by hot-pressing, leading to the total collapse of cell walls and the complete densification of the natural wood with highly aligned cellulose nanofibres. This strategy is shown to be universally effective for various species of wood. Our processed wood has a specific strength higher than that of most structural metals and alloys, making it a low-cost, high-performance, lightweight alternative.

Evaluation of bolted connections in wood-plastic composites

Science.gov (United States)

Arnandha, Yudhi; Satyarno, Iman; Awaludin, Ali; Irawati, Inggar Septia; Ihsan, Muhamad; Wijanarko, Felyx Biondy; William, Mahdinur, Fardhani, Arfiati

2017-03-01

Wood-plastic composite (WPC) is a relatively new material that consists of sawdust and plastic polymer using the extrusion process. Due to its attributes such as low water content, low maintenance, UV durability and being fungi and termite resistant. Nowadays, WPC has already been produced in Indonesia using sawdust from local wood such as Albizia (Paraserianthes falcataria) and Teak (Tectona grandis). Moreover preliminary studies about the physical and mechanical WPC board from Albizia sawdust and HDPE plastic have been carried out. Based on these studies, WPC has a high shear strength around 25-30 MPa higher than its original wood shear strength. This paper was a part of the research in evaluating WPC as potential sheathing in a shear wall system. Since still little is known about connection behavior in WPC using Indonesian local wood, this study evaluated the connection for both of these two types of wood-plastic composite. WPC board from Albizia sawdust will be projected as shear wall sheathing and WPC stud from Teak sawdust projected to be shear wall frame. For this study, the embedding strength for both WPC was determined according to ASTM D 5764 standard, using two types of bolts (stainless bolt and standard bolt) with several diameters as variation (6 mm, 8 mm, 10 and 12 mm). Hence, dowel-bearing test under fastened condition conducted accordance to ASTM D5652, hereby the yield strength then compared with the prediction yield strength from European Yield Model (EYM). According to both single and double shear connection, it can be concluded that yield strength from the EYM method tended to under-predict the 5% diameter offset yield than the actual yield strength from the test. The yield strength itself increase with the increase of bolt diameter. For single shear connection, the highest yield strength was 12 mm standard bolt around 9732 N, slightly higher than stainless bolt around 9393 N. Whereby for double shear connection, the highest yield strength was

Effects of swelling forces on the durability of wood adhesive bonds

Science.gov (United States)

Blake M. Hofferber; Edward Kolodka; Rishawn Brandon; Robert J. Moon; Charles R. Frihart

2006-01-01

The purpose of this study was to investigate the role of wood swelling on performance of wood-adhesive bonds (resorcinol formaldehyde, epoxy, emulsion polymerisocyanate), for untreated and acetylated wood. Effects of these treatments on measured strain anisotropy and swelling stress were measured and then related to compressive shear strength and percentage wood...

Derivation of nominal strength for wood utility poles

Science.gov (United States)

Ronald W. Wolfe; Jozsef Bodig; Patricia Lebow

2001-01-01

The designated fiber stress values published in the American National Standards Institute Standard for Poles, ANSI 05.1, no longer reflect the state of the knowledge. These values are based on a combination of test data from small clear wood samples and small poles (

FLEXURAL TESTING OF WOOD-CONCRETE COMPOSITE BEAM MADE FROM KAMPER AND BANGKIRAI WOOD

Directory of Open Access Journals (Sweden)

Fengky Satria Yoresta

2015-07-01

Full Text Available Certain wood has a tensile strength that almost equal with steel rebar in reinforced concrete beams. This research aims to understand the capacity and flexural behavior of concrete beams reinforced by wood (wood-concrete composite beam. Two different types of beams based on placement positions of wood layers are proposed in this study. Two kinds of wood used are consisted of Bangkirai (Shorea laevifolia and Kamper (Cinnamomum camphora, meanwhile the concrete mix ratio for all beams is 1 cement : 2 fine aggregates : 3 coarse aggregates. Bending test is conducted by using one-point loading method. The results show that composite beam using Bangkirai wood is stronger than beams using Kamper wood. More thicker wood layer in tensile area will increase the flexural strength of beams. Crack patterns identified could be classified into flexural cracks, shear cracks, and split on wood layer   Beberapa jenis kayu tertentu memiliki kekuatan tarik yang hampir sama dengan tulangan baja pada balok beton bertulang. Penelitian ini bertujuan memahami kapasitas dan perilaku lentur balok beton bertulang yang diperkuat menggunakan kayu (balok komposit beton-kayu. Dua tipe balok yang berbeda berdasarkan posisi penempatan kayu digunakan dalam penelitian ini. Dua jenis kayu yang digunakan adalah kayu Bangkirai (Shorea laevifolia and Kamper (Cinnamomum camphora, sementara itu rasio campuran beton untuk semua balok menggunakan perbandingan 1 semen : 2 agregat halus : 3 agregat kasar. Pengujian lentur dilakukan menggunakan metode one-point loading. Hasil penelitian menunjukkan bahwa balok komposit dengan kayu Bangkirai lebih kuat dibandingkan balok dengan kayu Kamper. Semakin tebal lapisan kayu yang berada di daerah tarik akan meningkatkan kekuatan lentur balok. Pola kerusakan yang teridentifikasi dapat diklasifikasikan menjadi retak lentur, retak geser, dan pecah pada kayu REFERENCES Boen T. (2010. Retrofitting Simple Buildings Damaged by Earthquakes. World Seismic

Cellulose-hemicellulose interaction in wood secondary cell-wall

International Nuclear Information System (INIS)

Zhang, Ning; Li, Shi; Hong, Yu; Chen, Youping; Xiong, Liming

2015-01-01

The wood cell wall features a tough and relatively rigid fiber reinforced composite structure. It acts as a pressure vessel, offering protection against mechanical stress. Cellulose microfibrils, hemicellulose and amorphous lignin are the three major components of wood. The structure of secondary cell wall could be imagined as the same as reinforced concrete, in which cellulose microfibrils acts as reinforcing steel bar and hemicellulose-lignin matrices act as the concrete. Therefore, the interface between cellulose and hemicellulose/lignin plays a significant role in determine the mechanical behavior of wood secondary cell wall. To this end, we present a molecular dynamics (MD) simulation study attempting to quantify the strength of the interface between cellulose microfibrils and hemicellulose. Since hemicellulose binds with adjacent cellulose microfibrils in various patterns, the atomistic models of hemicellulose-cellulose composites with three typical binding modes, i.e. bridge, loop and random binding modes are constructed. The effect of the shape of hemicellulose chain on the strength of hemicellulose-cellulose composites under shear loadings is investigated. The contact area as well as hydrogen bonds between cellulose and hemicellulose, together with the covalent bonds in backbone of hemicellulose chain are found to be the controlling parameters which determine the strength of the interfaces in the composite system. For the bridge binding model, the effect of shear loading direction on the strength of the cellulose material is also studied. The obtained results suggest that the shear strength of wood-inspired engineering composites can be optimized through maximizing the formations of the contributing hydrogen bonds between cellulose and hemicellulose. (paper)

Cellulose-hemicellulose interaction in wood secondary cell-wall

Science.gov (United States)

Zhang, Ning; Li, Shi; Xiong, Liming; Hong, Yu; Chen, Youping

2015-12-01

The wood cell wall features a tough and relatively rigid fiber reinforced composite structure. It acts as a pressure vessel, offering protection against mechanical stress. Cellulose microfibrils, hemicellulose and amorphous lignin are the three major components of wood. The structure of secondary cell wall could be imagined as the same as reinforced concrete, in which cellulose microfibrils acts as reinforcing steel bar and hemicellulose-lignin matrices act as the concrete. Therefore, the interface between cellulose and hemicellulose/lignin plays a significant role in determine the mechanical behavior of wood secondary cell wall. To this end, we present a molecular dynamics (MD) simulation study attempting to quantify the strength of the interface between cellulose microfibrils and hemicellulose. Since hemicellulose binds with adjacent cellulose microfibrils in various patterns, the atomistic models of hemicellulose-cellulose composites with three typical binding modes, i.e. bridge, loop and random binding modes are constructed. The effect of the shape of hemicellulose chain on the strength of hemicellulose-cellulose composites under shear loadings is investigated. The contact area as well as hydrogen bonds between cellulose and hemicellulose, together with the covalent bonds in backbone of hemicellulose chain are found to be the controlling parameters which determine the strength of the interfaces in the composite system. For the bridge binding model, the effect of shear loading direction on the strength of the cellulose material is also studied. The obtained results suggest that the shear strength of wood-inspired engineering composites can be optimized through maximizing the formations of the contributing hydrogen bonds between cellulose and hemicellulose.

Status of wood-based industries in Malaysia

International Nuclear Information System (INIS)

Dahlan Haji Mohd

1987-01-01

Malaysia is one of the biggest suppliers of tropical wood in the world. However, less than 10% of the timber exported have gone through secondary processing. It is high time for this country to concentrate more on the secondary and tertiary sectors with the use of new technology such as radiation curing of coatings, in order to improve the quality of wood products. This paper examines where the strength and potential of the local wood industry lie. (author)

Fire performance, mechanical strength and dimensional stability of wood flour–polyethylene composites under the influence of different fire retardants

Directory of Open Access Journals (Sweden)

Mehdi Roohani

2017-05-01

Full Text Available Flammability is one of the most important parameters that often limit the application range of wood plastic composites. Therefore, the improvements of retardancy performance of these products have a considerable impact. The aim of this work was to evaluate the influence of expandable graphite (EG and its combination with aluminum tirhydroxide (ATH, inorganic phosphate (IP and melamine borate (MB on the flammability of wood flour–polyethylene composites. Composites were prepared by the melt compounding method and cone calorimetry as well as limited oxygen index (LOI tests was employed to study their flammability properties. Also, the effect of different fire retardants on the mechanical strength and water uptake of samples were investigated. Cone calorimetry characterization indicated that with incorporation of fire retardans heat release rate and burning rate decrease and char residual as well as the time to ignition increase. These findings ascribed to formation of char layer by fire retardants. The combination of EG and other fire retardants yielded better improvements in flame retardancy in comparison to the sample that has just EG as flame retardant. The LOI test was used to determine the lowest concentration of oxygen at which a material will maintain combustion in a flowing mixture of oxygen and nitrogen. The results showed that inclusion of fire retardants improve the LOI of sample. Furthermore, the presence of fire retardants decreased the tensile and flexural resistance (strength and modules and impact strength of samples, and increased the water absorption as well as thickness swelling. Generally, among the different treatments examined, the EG–ATH retardancy system showed highest potential in flame retardancy of composites.

Impact of cold temperatures on the shear strength of Norway spruce joints glued with different adhesives

DEFF Research Database (Denmark)

Wang, Xiaodong; Hagman, Olle; Sundqvist, Bror

2015-01-01

As wood construction increasingly uses engineered wood products worldwide, concerns arise about the integrity of the wood and adhesives used. Bondline strength is a crucial issue for engineered wood applications, especially in cold climates. In this study, Norway spruce (Picea abies) joints (150 mm...... adhesive was tested at six temperatures: 20, −20, −30, −40, −50 and −60 °C. Generally, within the temperature test range, temperature changes significantly affected the shear strength of solid wood and wood joints. As the temperature decreased, the shear strength decreased. PUR adhesive in most cases...... resulted in the strongest shear strength and MUF adhesive resulted in the weakest. MF and PRF adhesives responded to temperature changes in a similar manner to that of the PUR adhesive. The shear strengths of wood joints with PVAc and EPI adhesives were more sensitive to temperature change. At low...

Theoretical modeling and experimental analyses of laminated wood composite poles

Science.gov (United States)

Cheng Piao; Todd F. Shupe; Vijaya Gopu; Chung Y. Hse

2005-01-01

Wood laminated composite poles consist of trapezoid-shaped wood strips bonded with synthetic resin. The thick-walled hollow poles had adequate strength and stiffness properties and were a promising substitute for solid wood poles. It was necessary to develop theoretical models to facilitate the manufacture and future installation and maintenance of this novel...

Optimising hydrogen bonding in solid wood

DEFF Research Database (Denmark)

Engelund, Emil Tang

2009-01-01

The chemical bonds of wood are both covalent bonds within the wood polymers and hydrogen bonds within and between the polymers. Both types of bonds are responsible for the coherence, strength and stiffness of the material. The hydrogen bonds are more easily modified by changes in load, moisture...... and temperature distorting the internal bonding state. A problem arises when studying hydrogen bonding in wood since matched wood specimens of the same species will have very different internal bonding states. Thus, possible changes in the bonding state due to some applied treatment such as conditioning...... maintaining 100 % moisture content of the wood. The hypothesis was that this would enable a fast stress relaxation as a result of reorganization of bonds, since moisture plasticizes the material and temperature promotes faster kinetics. Hereby, all past bond distortions caused by various moisture, temperature...

Comparing energy use and environmental emissions of reinforced wood doors and steel doors

Science.gov (United States)

Lynn Knight; Melissa Huff; Janet I. Stockhausen; Robert J. Ross

2005-01-01

The USDA Forest Service Forest Products Laboratory has patented a technology that incorporates fiberglass-reinforced wood into the structure of wood doors and other wood building products. The process of reinforcing wood doors with epoxy and fiberglass increases the strength and durability of the product. Also, it allows the use of low-value, small-diameter wood which...

Mechanical properties: wood lumber versus plastic lumber and thermoplastic composites

Directory of Open Access Journals (Sweden)

Bernardo Zandomenico Dias

Full Text Available Abstract Plastic lumber and thermoplastic composites are sold as alternatives to wood products. However, many technical standards and scientific studies state that the two materials cannot be considered to have the same structural behaviour and strength. Moreover, there are many compositions of thermoplastic-based products and plenty of wood species. How different are their mechanical properties? This study compares the modulus of elasticity and the flexural, compressive, tensile and shear strengths of such materials, as well as the materials' specific mechanical properties. It analyses the properties of wood from the coniferae and dicotyledon species and those of commercialized and experimental thermoplastic-based product formulations. The data were collected from books, scientific papers and manufacturers' websites and technical data sheets, and subsequently compiled and presented in Ashby plots and bar graphs. The high values of the compressive strength and specific compressive and tensile strengths perpendicular to the grain (width direction shown by the experimental thermoplastic composites compared to wood reveal their great potential for use in compressed elements and in functions where components are compressed or tensioned perpendicularly to the grain. However, the low specific flexural modulus and high density of thermoplastic materials limit their usage in certain civil engineering and building applications.

Microbuckling compression failure of a radiation-induced wood/polymer composite

International Nuclear Information System (INIS)

Boey, F.Y.C.

1990-01-01

A wood/polymer composite was produced by impregnating Ramin wood with methyl methacrylate monomer and subsequently polymerizing it by gamma irradiation. To assess the improvement in compression strength of the wood caused by the polymer impregnation, a microbuckling compression failure mechanism was used to model the compression failure of the composite. Such a mechanism was found to predict a linear relationship between the compression strength and the percentage polymer impregnation (by weight). Uniaxial compression test results at 45(±5)% and 90(±5)% relative humidity levels, after being statistically analysed, showed that such a linear relationship was valid for up to 100% polymer impregnation. (author)

Basalt FRP Spike Repairing of Wood Beams

Directory of Open Access Journals (Sweden)

Luca Righetti

2015-08-01

Full Text Available This article describes aspects within an experimental program aimed at improving the structural performance of cracked solid fir-wood beams repaired with Basalt Fiber Reinforced Polymer (BFRP spikes. Fir wood is characterized by its low density, low compression strength, and high level of defects, and it is likely to distort when dried and tends to fail under tension due to the presence of cracks, knots, or grain deviation. The proposed repair technique consists of the insertion of BFRP spikes into timber beams to restore the continuity of cracked sections. The experimental efforts deal with the evaluation of the bending strength and deformation properties of 24 timber beams. An artificially simulated cracking was produced by cutting the wood beams in half or notching. The obtained results for the repaired beams were compared with those of solid undamaged and damaged beams, and increases of beam capacity, bending strength and of modulus of elasticity, and analysis of failure modes was discussed. For notched beams, the application of the BFRP spikes was able to restore the original bending capacity of undamaged beams, while only a small part of the original capacity was recovered for beams that were cut in half.

A Study on the Effect of Plasma Treatment for Waste Wood Biocomposites

Directory of Open Access Journals (Sweden)

MiMi Kim

2013-01-01

Full Text Available The surface modification of wood powder by atmospheric pressure plasma treatment was investigated. The composites were manufactured using wood powder and polypropylene (wood powder: polypropylene = 55 wt% : 45 wt%. Atmospheric pressure plasma treatment was applied under the condition of 3 KV, 17±1 KHz, 2 g/min. Helium was used as the carrier gas and hexamethyl-disiloxane (HMDSO as the monomer to modify the surface property of the waste wood biocomposites by plasma polymerization. The tensile strengths of untreated waste wood powder (W3 and single species wood powder (S3 were about 18.5 MPa and 21.5 MPa while those of plasma treated waste wood powder (PW3 and plasma treated single species wood powder (PS3 were about 21.2 MPa and 23.4 MPa, respectively. Tensile strengths of W3 and S3 were improved by 14.6% and 8.8%, respectively. From the analyses of mechanical properties and morphology, we conclude that the interfacial bonding of polypropylene and wood powder can be improved by atmospheric pressure plasma treatment.

Improvement of wood quality used in Syria by irradiation polymerization

International Nuclear Information System (INIS)

Bakarji, E. H.

2002-06-01

Wood plastic composites (WPC) have been prepared with five low-grade woods, native to Syria, and with Okoume (aucoumea klaineana pierre) imported to Syria in large quantities. Three monomer systems; acrylamide, butylmethacrylate, and styrene were used. polymerization was induced at various radiation doses (10, 20, and 30 kGy) to study the role of radiation doses using a 60 Co gamma radiation source. Some physical properties of WPC, namely polymer loading and compression strength or tensile strength of the obtained wood polymer composites (WPC) were studied. The effect of the additives, sulfuric acid (H + ), N-vinyl pyrrolidone (NVP), trimethyolpropane triacrylate (TMPTA), urea (U), lithium nitrate (LiNo 3 ), copper sulfate (CuSO 4 ) and co-additives on monomer system polymerization were also investigated. Methanol, water and water/methanol mixtures were used as the swelling agents. In general, the use of additives and co-additives brought about an enhancement of tensile strength or compression strength and polymer loading of the composites. In some cases, additives also lowered the monomer concentration and the gamma radiation dose required for polymerization (author)

Compressive Fatigue in Wood

DEFF Research Database (Denmark)

Clorius, Christian Odin; Pedersen, Martin Bo Uhre; Hoffmeyer, Preben

1999-01-01

An investigation of fatigue failure in wood subjected to load cycles in compression parallel to grain is presented. Small clear specimens of spruce are taken to failure in square wave formed fatigue loading at a stress excitation level corresponding to 80% of the short term strength. Four...... frequencies ranging from 0.01 Hz to 10 Hz are used. The number of cycles to failure is found to be a poor measure of the fatigue performance of wood. Creep, maximum strain, stiffness and work are monitored throughout the fatigue tests. Accumulated creep is suggested identified with damage and a correlation...

EFFECT OF CHEMICAL MODIFICATION AND HOT-PRESS DRYING ON POPLAR WOOD

Directory of Open Access Journals (Sweden)

Guo-Feng Wu

2010-11-01

Full Text Available Urea-formaldehyde prepolymer and hot-press drying were used to improve the properties of poplar wood. The wood was impregnated with the prepolymer using a pulse-dipping machine. The impregnated timbers were compressed and dried by a multilayer hot-press drying kiln. The drying rate was more rapid during the chemical modification and hot-press drying than conventional kiln-drying. In addition, the properties of timber were also enhanced obviously. When the compression rate was 28.6%, the basic density, oven dry density and air-dried density of modified wood improved 22%, 71%, and 70%, respectively. The bending strength and compressive strength parallel to grain increased 60% and 40%. The water uptake of treated wood was significantly decreased compared with the untreated wood. The FTIR analysis successfully showed that the intensity of hydroxyl and carbonyl absorption peaks decreased significantly, which was attributed to a reaction of the NHCH2OH of urea-formaldehyde prepolymer with the wood carboxyl (C=O and hydroxyl (-OH groups. The XRD results indicated that the degree of crystallinity increased from 35.09% to 36.91%. The morphologic models of chemical within wood were discovered by SEM.

Evaluation of wood species and preservatives for WisDOT sign posts.

Science.gov (United States)

2013-10-01

The Wisconsin Department of Transportation (WisDOT) uses preservative-treated wood posts for much of the signage along state highways because wood is relatively inexpensive, easy to install, and has the necessary strength properties to tolerate typic...

Potential of Reinforced Indonesian Glulam Beams Using Grade I (Bengkirai, Grade II (Kamper, Grade III (Nyatoh Woods for Use in Structural Wood Design

Directory of Open Access Journals (Sweden)

Saptahari Sugiri

2016-05-01

Full Text Available Wood is a natural resource that is renewable and available in various species in tropical countries. Its abundancy in nature makes it easy to obtain, thus making it a nature friendly material for use in construction. Indonesia is the most important source of tropical wood in the world after Brazil, making the use of wood for structural elements very desirable. It is estimated that 4000 different varieties of wood exist in Indonesia. This estimate is based on the herbarium species collected by the Forestry Research Institute, currently counting nearly 4000 types of trees with a diameter of more than 40 cm. In the Indonesian wood structure code, the strength of woods is divided into 3 grades (grade I, II and III. This paper presents an evaluation of the mechanical properties of glulam wood sourced from native Indonesian timber: Bengkirai wood (grade I, Kamper wood (grade II, and Nyatoh wood (grade III, thus proving the potential for Indonesian wood as industrial structural elements in wooden constructions.

Effect of changing slope of grain on ash, maple, and yellow birch in bending strength

Science.gov (United States)

David E. Kretschmann; James J. Bridwell; Timothy C. Nelson

2010-01-01

The presence of slope of grain (SoG) in wood can severely reduce the bending strength in wood. Failure to recognize the degree to which SoG can reduce strength can be catastrophic if wood is in single member use. In the United States, a growing concern in the sport of baseball relates to the high frequency of multi-piece broken wood bats. It was observed that hard...

Characteristics and modeling of spruce wood under dynamic compression load

International Nuclear Information System (INIS)

Eisenacher, Germar

2014-01-01

Spruce wood is frequently used as an energy absorbing material in impact limiters of packages for the transportation of radioactive material. A 9m drop test onto an unyielding target is mandatory for the packages. The impact results in a dynamic compression load of the spruce wood inside the impact limiter. The lateral dilation of the wood is restrained thereby due to encasing steel sheets. This work's objective was to provide a material model for spruce wood based on experimental investigations to enable the calculation of such loading conditions. About 600 crush tests with cubical spruce wood specimens were performed to characterize the material. The compression was up to 70% and the material was assumed to be transversely isotropic. Particularly the lateral constraint showed to have an important effect: the material develops a high lateral dilation without lateral constraint. The force-displacement characteristics show a comparably low force level and no or only slight hardening. Distinctive softening occurs after the linear-elastic region when loaded parallel to the fiber. On the other hand, using a lateral constraint results in significantly higher general force levels, distinctive hardening and lateral forces. The softening effect when loaded parallel to the fiber is less distinctive. Strain rate and temperature raise or lower the strength level, which was quantified for the applicable ranges of impact limiters. The hypothesis of an uncoupled evolution of the yield surface was proposed based on the experimental findings. It postulates an independent strength evolution with deviatoric and volumetric deformation. The hypothesis could be established using the first modeling approach, the modified LS-DYNA material model MAT075. A transversely isotropic material model was developed based thereupon and implemented in LS-DYNA. The material characteristics of spruce wood were considered using a multi-surface yield criterion and a non-associated flow rule. The yield

Wood Sawdust/Natural Rubber Ecocomposites Cross-Linked by Electron Beam Irradiation

Directory of Open Access Journals (Sweden)

Elena Manaila

2016-06-01

Full Text Available The obtaining and characterization of some polymeric eco-composites based on wood sawdust and natural rubber is presented. The natural rubber was cross-linked using the electron beam irradiation. The irradiation doses were of 75, 150, 300 and 600 kGy and the concentrations of wood sawdust were of 10 and 20 phr, respectively. As a result of wood sawdust adding, the physical and mechanical properties such as hardness, modulus at 100% elongation and tensile strength, showed significant improvements. The presence of wood sawdust fibers has a reinforcing effect on natural rubber, similar or better than of mineral fillers. An increase in the irradiation dose leads to the increasing of cross-link density, which is reflected in the improvement of hardness, modulus at 100% elongation and tensile strength of blends. The cross-linking rates, appreciated using the Flory-Rehner equation, have increased with the amount of wood sawdust in blends and with the irradiation dose. Even if the gel fraction values have varied irregularly with the amount of wood sawdust and irradiation dose it was over 90% for all blends, except for the samples without wood sawdust irradiated with 75 kGy. The water uptake increased with increasing of fiber content and decreased with the irradiation dose.

Advances in the study of mechanical properties and constitutive law in the field of wood research

Science.gov (United States)

Zhao, S.; Zhao, J. X.; Han, G. Z.

2016-07-01

This paper presents an overview of mechanical properties and constitutive law for wood. Current research on the mechanical properties of wood have mostly focused on density, grain, moisture, and other natural factors. It has been established that high density, dense grain, and high moisture lead to higher strength. In most literature, wood has been regarded as an anisotropic material because of its fiber. A microscopic view is used in research of wood today, in this way, which has allowed for clear observation of anisotropy. In general, wood has higher strength under a dynamic load, and no densification. The constitutive model is the basis of numerical analysis. An anisotropic model of porous and composite materials has been used for wood, but results were poor, and new constitutions have been introduced. According to the literature, there is no single theory that is widely accepted for the dynamic load. Research has shown that grain and moisture are key factors in wood strength, but there has not been enough study on dynamic loads so far. Hill law has been the most common method of simulation. Models that consider high strain rate are attracting more and more attention.

Conventional compressive strength parallel to the grain and mechanical resistance of wood against pin penetration and microdrilling established by in-situ semidestructive devices

Czech Academy of Sciences Publication Activity Database

Kloiber, Michal; Drdácký, Miloš; Tippner, J.; Hrivnák, J.

2015-01-01

Roč. 48, č. 10 (2015), s. 3217-3229 ISSN 1359-5997 R&D Projects: GA MK(CZ) DF11P01OVV001; GA MŠk(CZ) LO1219 Keywords : compressive strength * density * in situ testing * non-destructive testing (NDT) * small size loading jack * wood Subject RIV: AL - Art, Architecture, Cultural Heritage Impact factor: 2.453, year: 2015 http://link.springer.com/article/10.1617/s11527-014-0392-6

Effect of wood flour content on the optical color, surface chemistry, mechanical and morphological properties of wood flour/recycled high density polyethylene (rHDPE) composite

Science.gov (United States)

Sheng, Chan Kok; Amin, Khairul Anuar Mat; Kee, Kwa Bee; Hassan, Mohd Faiz; Ali, E. Ghapur E.

2018-05-01

In this study, effect of wood flour content on the color, surface chemistry, mechanical properties and surface morphology of wood-plastic composite (WPC) on different mixture ratios of recycled high density polyethylene (rHDPE) and wood flour were investigated in detail. The presence of wood flour in the composite indicates a significant total color change and a decrease of lightness. Functional groups of wood flour in WPC can be seen clearer from the Fourier transform infrared (FTIR) spectra as the wood flour content increases. The mechanical tensile testing shows that the tensile strength of Young's modulus is improved, whereas the strain and elongation at break were reduced by the addition of wood flour. The gap between the wood flour microvoid fibre and rHDPE matrix becomes closer when the wood flour content is increased as observed by scanning electron microscope (SEM) image. This finding implies a significant improvement on the interaction of interfacial adhesion between the rHDPE matrix and wood flour filler in the present WPC.

Intraspecific variability of European larch for wood properties: Preliminary results

Energy Technology Data Exchange (ETDEWEB)

Paques, L.E.; Rozenberg, P. [Institut National de Recherches Agronomiques (INRA), 45 - Olivet (France). Station d`Amelioration des Arbres Forestiers

1995-12-31

Wood properties of several natural populations of European larch (Larix decidua Mill) were determined from samples collected in one replicate of the II. International IUFRO provenance experiment, planted in Brittany in 1959. According to provenances, proportion of heartwood ranges from 35 to 58% of basal area, basic density from 442 to 505 g/dm{sup 3} and Young modulus of elasticity from 8474 to 14522 MPa. Positive correlations between girth and heartwood proportion and between wood density and modulus of elasticity but negative correlations between ring width and both density and MOE have been found both at the individual and at the population levels. Variability between and within provenances is high for two major traits (proportion of heartwood and Young modulus of elasticity) for which a SW - NE gradient is shown. For wood density parameters including pilodyn, a greater homogeneity is observed. Besides a now largely recognized superiority for growth traits, Central European populations from the Sudetan Mountains and Central Poland would also produce wood with better properties. On the reverse, Alpine populations from the French Alps growing at low elevations have a slower growth, a denser wood with less heartwood and less strength. Used as a control, the hybrid larch origin (Larix x eurolepis) represents the best compromise for wood properties with the highest strength but an average wood density and one of the highest proportion of heartwood. These preliminary results must be confirmed from a larger set of provenances and completed with other major wood properties such as durability and shrinkage. 17 refs, 2 figs, 6 tabs

Intraspecific variability of European larch for wood properties: Preliminary results

Energy Technology Data Exchange (ETDEWEB)

Paques, L E; Rozenberg, P [Institut National de Recherches Agronomiques (INRA), 45 - Olivet (France). Station d` Amelioration des Arbres Forestiers

1996-12-31

Wood properties of several natural populations of European larch (Larix decidua Mill) were determined from samples collected in one replicate of the II. International IUFRO provenance experiment, planted in Brittany in 1959. According to provenances, proportion of heartwood ranges from 35 to 58% of basal area, basic density from 442 to 505 g/dm{sup 3} and Young modulus of elasticity from 8474 to 14522 MPa. Positive correlations between girth and heartwood proportion and between wood density and modulus of elasticity but negative correlations between ring width and both density and MOE have been found both at the individual and at the population levels. Variability between and within provenances is high for two major traits (proportion of heartwood and Young modulus of elasticity) for which a SW - NE gradient is shown. For wood density parameters including pilodyn, a greater homogeneity is observed. Besides a now largely recognized superiority for growth traits, Central European populations from the Sudetan Mountains and Central Poland would also produce wood with better properties. On the reverse, Alpine populations from the French Alps growing at low elevations have a slower growth, a denser wood with less heartwood and less strength. Used as a control, the hybrid larch origin (Larix x eurolepis) represents the best compromise for wood properties with the highest strength but an average wood density and one of the highest proportion of heartwood. These preliminary results must be confirmed from a larger set of provenances and completed with other major wood properties such as durability and shrinkage. 17 refs, 2 figs, 6 tabs

Influence of extractives on wood gluing and finishing- a review

Science.gov (United States)

Chung-Yun Hse; Mon-Lin Kuo

1988-01-01

Migration of extractives to the wood surface alters the properties of wood as an adherent. Extractives change the wettability and the curing properties of adhesives. A desirable wettability-permeability relationship is sometimes affected by extractives, thus reducing the gluebond strength and performance. Past efforts to determine which of the components of extractives...

Wood and concrete polymer composites

International Nuclear Information System (INIS)

Singer, K.

1974-01-01

There are several ways to prepare and use wood and concrete polymer composites. The most important improvements in the case of concrete polymer composites are obtained for compressive and tensile strengths. The progress in this field in United States and other countries is discussed in this rview. (M.S.)

BASIC PROPERTIES IN RELATION TO DRYING PROPERTIES OF THREE WOOD SPECIES FROM INDONESIA

Directory of Open Access Journals (Sweden)

Efrida Basri

2005-03-01

Full Text Available The objectives of this study were to investigate basic and drying properties of three wood species from Indonesia, i.e. kuda (Lannea coromandelica Merr., waru (Hibiscus tiliaceus L. and mindi besar (Melia dubia Cav.. The basic properties include density, shrinkages, modulus of rupture (MOR, compression parallel to grain (C//, wood strength and anatomical structures. Meanwhile, the drying properties included drying time and drying defects. The initial-final temperature and humidity for each species was based on defects that resulted from high temperature drying trial. The results showed that the drying properties were significantly affected by wood anatomical structure. The initial-final drybulb temperature and wetbulb depression   for kuda wood are 50 -70ºC and 3-30ºC respectively, while the corresponding figures for waru wood are 65-80ºC and 6-30ºC, and for mindi besar wood are 55-80ºC and 4-30ºC. These drying schedules, however, still need further trial prior to their implementation in the factory-scale operation. All wood species studied have density and considerable strength recommended in their use for light medium construction purposes. Mindi besar wood has decorative appearance so it is suitable for furniture.

Mechanical properties of wood from Pinus sylvestris L. treated with Light Organic Solvent Preservative and with waterborne Copper Azole

Directory of Open Access Journals (Sweden)

A.M. Villasante

2013-12-01

Full Text Available Aim of study: To determine the effect on wood from Pinus sylvestris of treatment with preservatives on mechanical properties and to establish the relation between the penetration and compression strength.Area of study: SpainMaterial and Methods: 40 samples of defect-free wood from Pinus sylvestris L. were treated with Light Organic Solvent Preservative (Vacsol Azure WR 2601 and 50 with waterborne Copper Azole (Tanalith E 3492. 40 control samples were not treated (water or preservative. Mechanical resistance to static bending, modulus of elasticity and compression strength parallel to the grain were compared with untreated wood. Regression analysis between the penetration and compression strength parallel was done with the samples treated with waterborne preservative.Main results: The results indicate that the treated wood (with either product presents a statistically significant increase in mechanical resistance in all three mechanical characteristics. The results obtained differ from earlier studies carried out by other authors.There was no correlation between parallel compression strength and the degree of impregnation of the wood with waterborne Copper Azole . The most probable explanation for these results concerns changes in pressure during treatment.The use of untreated control samples instead of samples treated only with water is more likely to produce significant results in the mechanical resistance studies.Research highlights: Treated wood presents a statistically significant increase in MOE, modulus of rupture to static bending  and parallel compression strength.There was no correlation between parallel compression strength and the degree of impregnation with waterborne preservative.Keywords: Light Organic Solvent Preservative; MOE; parallel compression; static bending; waterborne Copper Azole; wood technology.

Fabrication and Spectral Properties of Wood-Based Luminescent Nanocomposites

Directory of Open Access Journals (Sweden)

Xianjun Li

2014-01-01

Full Text Available Pressure impregnation pretreatment is a conventional method to fabricate wood-based nanocomposites. In this paper, the wood-based luminescent nanocomposites were fabricated with the method and its spectral properties were investigated. The results show that it is feasible to fabricate wood-based luminescent nanocomposites using microwave modified wood and nanophosphor powders. The luminescent strength is in positive correlation with the amount of phosphor powders dispersed in urea-formaldehyde resin. Phosphors absorb UV and blue light efficiently in the range of 400–470 nm and show a broad band of bluish-green emission centered at 500 nm, which makes them good candidates for potential blue-green luminescent materials.

Effects of copper amine treatments on mechanical, biological and surface/interphase properties of poly (vinyl chloride)/wood composites

Science.gov (United States)

Jiang, Haihong

2005-11-01

The copper ethanolamine (CuEA) complex was used as a wood surface modifier and a coupling agent for wood-PVC composites. Mechanical properties of composites, such as unnotched impact strength, flexural strength and flexural toughness, were significantly increased, and fungal decay weight loss was dramatically decreased by wood surface copper amine treatments. It is evident that copper amine was a very effective coupling agent and decay inhibitor for PVC/wood flour composites, especially in high wood flour loading level. A DSC study showed that the heat capacity differences (DeltaCp) of composites before and after PVC glass transition were reduced by adding wood particles. A DMA study revealed that the movements of PVC chain segments during glass transition were limited and obstructed by the presence of wood molecule chains. This restriction effect became stronger by increasing wood flour content and by using Cu-treated wood flour. Wood flour particles acted as "physical cross-linking points" inside the PVC matrix, resulting in the absence of the rubbery plateau of PVC and higher E', E'' above Tg, and smaller tan delta peaks. Enhanced mechanical performances were attributed to the improved wetting condition between PVC melts and wood surfaces, and the formation of a stronger interphase strengthened by chemical interactions between Cu-treated wood flour and the PVC matrix. Contact angles of PVC solution drops on Cu-treated wood surfaces were decreased dramatically compared to those on the untreated surfaces. Acid-base (polar), gammaAB, electron-acceptor (acid) (gamma +), electron-donor (base) (gamma-) surface energy components and the total surface energies increased after wood surface Cu-treatments, indicating a strong tendency toward acid-base or polar interactions. Improved interphase and interfacial adhesion were further confirmed by measuring interfacial shear strength between wood and the PVC matrix.

Fracture mechanics and statistical modeling of ternary blends of polylactide/ethylene-acrylate copolymer /wood-flour composites

Science.gov (United States)

Afrifah, Kojo Agyapong

This study examined the mechanisms of toughening the brittle bio-based poly(lactic acid) (PLA) with a biodegradable rubbery impact modifier to develop biodegradable and cost effective PLA/wood-flour composites with improved impact strength, toughness, high ductility, and flexibility. Semicrystalline and amorphous PLA grades were impact modified by melt blending with an ethylene-acrylate copolymer (EAC) impact modifier. EAC content was varied to study the effectiveness and efficiency of the impact modifier in toughening the semicrystalline and amorphous grades of the PLA. Impact strength was used to assess the effectiveness and efficiency of the EAC in toughening the blends, whereas the toughening mechanisms were determined with the phase morphologies and the miscibilities of the blends. Subsequent tensile property analyses were performed on the most efficiently toughened PLA grade. Composites were made from PLA, wood flour of various particle sizes, and EAC. Using two-level factorial design the interaction between wood flour content, wood flour particle size, and EAC content and its effect on the mechanical properties of the PLA/wood-flour composites was statistically studied. Numerical optimization was also performed to statistically model and optimize material compositions to attain mechanical properties for the PLA/wood-flour composites equivalent to at least those of unfilled PLA. The J-integral method of fracture mechanics was applied to assess the crack initiation (Jin) and complete fracture (J f) energies of the composites to account for imperfections in the composites and generate data useful for engineering designs. Morphologies of the fractured surfaces of the composites were analyzed to elucidate the failure and toughening mechanisms of the composites. The EAC impact modifier effectively improved the impact strength of the PLA/EAC blends, regardless of the PLA type. However, the EAC was more efficient in the semicrystalline grades of PLA compared to the

Understanding decay resistance, dimensional stability and strength changes in heat treated and acetylated wood

Science.gov (United States)

Roger M. Rowell; Rebecca E. Ibach; James McSweeny; Thomas Nilsson

2009-01-01

Reductions in hygroscopicity, increased dimensional stability and decay resistance of heat-treated wood depend on decomposition of a large portion of the hemicelluloses in the wood cell wall. In theory, these hemicelluloses are converted to small organic molecules, water and volatile furan-type intermediates that can polymerize in the cell wall. Reductions in...

Mechanical properties of wood from Pinus sylvestris L. treated with Light Organic Solvent Preservative and with waterborne Copper Azole

Energy Technology Data Exchange (ETDEWEB)

Villasante, A.; Laina, R.; Rojas, J. A. M.; Rojas, I. M.; Vignote, S.

2013-07-01

Aim of study: To determine the effect on wood from Pinus sylvestris of treatment with preservatives on mechanical properties and to establish the relation between the penetration and compression strenght. Area of study: Spain. Material and methods: 40 samples of defect-free wood from Pinus sylvestris L. were treated with Light Organic Solvent Preservative (Vacsol Azure WR 2601) and 50 with waterborne Copper Azole (Tanalith E 3492). 40 control samples were not treated (water or preservative). Mechanical resistance to static bending, modulus of elasticity and compression strength parallel to the grain were compared with untreated wood. Regression analysis between the penetration and compression strength parallel was done with the samples treated with waterborne preservative. Main results: The results indicate that the treated wood (with either product) presents a statistically significant increase in mechanical resistance in all three mechanical characteristics. The results obtained differ from earlier studies carried out by other authors. There was no correlation between parallel compression strength and the degree of impregnation of the wood with waterborne Copper Azole. The most probable explanation for these results concerns changes in pressure during treatment. The use of untreated control samples instead of samples treated only with water is more likely to produce significant results in the mechanical resistance studies. Research highlights: Treated wood presents a statistically significant increase in MOE, modulus of rupture to static bending and parallel compression strength. There was no correlation between parallel compression strength and the degree of impregnation with waterborne preservative. (Author)

Radiation protection of waterlogged archaeological catalpa wood uncovered from Changtaiguan Xingyang

International Nuclear Information System (INIS)

Zhao Hongying; Wang Jingwu; Cui Guoshi

2008-01-01

Waterlogged archaeological catalpa wood uncovered from Changtaiguan was tentatively treated by gradient dehydration of ethanol concentration, replacement of PEG200DMA gradually, and 60 Co γ-rays radiation cur- ing with absorbed dose 30.72 kGy at dose rate 90.35 Gy/min. It can be found that the color and appearance of rein- forced archaeological wood with clear texture looks like original one. There is no cracking, no warping, and no glare on the wood surface. The Compression strength of reinforced ancient wood (33.06 MPa) is close to that of modem Catalpa wood. The maximum linear shrinkage of reinforced ancient wood is 1.05% in grain direction, 4.10% in radial direction, and 4.32% in tangential direction respectively compared with that of original sample. The linear shrinkage under the condition of 180 days storage in the ambient temperature and humidity is 0.076% in grain direction, 1.17% in radial direction, and 1.86% in tangential direction respectively. The linear shrinkage under the condition of 90 days storage in the temperature (25 ± 2) degree C and relative humidity (5 ± 2)% is 0.066% in grain direction, 0.115% in radial di- rection, and 0.279% in tangential direction respectively. The linear swelling ratio after 90 days storage in the temperature (25 ± 2) degree C and relative humidity (98 ± 2)% is 1.79% in grain direction, 2.42% in radial direction, and 2.61% in tangential direction respectively. It is confirmed by microstructure study that capillaries in residual wood has been filled with polymers, so that the wood mechanical strength and the shape stability is improved respectively. (authors)

EFFECTS OF EDGE COVERING ON TENSILE STRENGTH OF MDF

Directory of Open Access Journals (Sweden)

Yalçın ÖRS

1999-03-01

Full Text Available Dowels, 6, 8 and 10 mm ? diameters were bonded with PVAc adhesive on Medium Density Fiberboard (MDF. Edges were covered with 5, 8 and 12 mm beech wood materials, drilled 25 mm depth. Tensile strength measurments were made on the samples. The highest tensile strength value was given as 6 mm ? dowel and MDF covered with 8 mm thickness beech wood material (2.294 N/mm2, the lowest value was obtained with 10 mm ? dowel and with unprocessed MDF (1.314 N/mm2.

Physical-mechanical and anatomical characterization in 26-year-old Eucalyptus resinifera wood

Directory of Open Access Journals (Sweden)

Israel Luiz de Lima

Full Text Available In the present study, we aimed to characterize Eucalyptus resinifera wood through physical and mechanical assays and wood anatomy studies, as well as determine the relationships between the properties and anatomy of wood. We used samples collected from the area close to the bark of ten 26-year-old E. resinifera trees. We concluded that the specific gravity (Gb, compression (f c0, and shear parallel to grain (f v0 were ranked in strength classes C30, C40 and C60, respectively, and that volumetric shrinkage (VS was ranked as high. A positive relationship between Gb and f v0 results from the higher specific gravity associated with higher tissue proportion, in turn, causing higher shear strength. Higher ray frequency increases shear strength, because rays act as reinforcing elements. A negative relationship between VS and vessel diameter occurs because vessel walls are highly resistant to collapse, and since larger lumens represent a higher proportion of empty spaces, less tissue is available for shrinkage.

Wood versus metal in airplane construction

Science.gov (United States)

Seehase, H

1923-01-01

The aim of this article is to present, in broad outline, a scientific method for solving the problem, "Wood or Metal." It will be shown that structural methods have by no means reached their final perfection. The strength of the different materials is discussed as well as different construction methods.

Heat Resistance of Glued Finger Joints in Spruce Wood Constructions

Directory of Open Access Journals (Sweden)

Martin Sviták

2014-10-01

Full Text Available The heat resistance of glued spruce wood was evaluated for different joint types and adhesives. Bending strength, modulus of elasticity, and also fracture evaluation were investigated on glued spruce samples made by the finger-jointed principle. Finger-jointed samples were glued with polyurethane (PUR and melamine-urea-formaldehyde (MUF adhesives. Heat loading was realized at temperatures 60, 80, and 110 °C and compared with wood with 20 °C. A static bending test with four-point flexural test was used. Elevated temperature and adhesive type had an important influence on the bending strength. On the other hand, adhesive type had a significant influence on the modulus of elasticity, but elevated temperature had no substantial influence.

Modeling the Effect of Nail Corrosion on the Lateral Strength of Joints

Science.gov (United States)

Samuel L. Zelinka; Douglas R. Rammer

2012-01-01

This article describes a theoretical method of linking fastener corrosion in wood connections to potential reduction in lateral shear strength. It builds upon published quantitative data of corrosion rates of metals in contact with treated wood for several different wood preservatives. These corrosion rates are then combined with yield theory equations to calculate a...

Online resources for the identification of North American wood decay fungi

Science.gov (United States)

Jessie A. Glaeser

2012-01-01

The ability to identify wood decay fungi is an important skill for an arborist. Knowing which fungus is colonizing a tree can be used to better assess the type, amount, and position of decay in the tree, and its subsequent effects on wood strength. Distinguishing species of fungi that colonize sapwood, heartwood, or roots can provide information to improve the quality...

Physical, mechanical, and biodegradable properties of meranti wood polymer composites

International Nuclear Information System (INIS)

Enamul Hoque, M.; Aminudin, M.A.M.; Jawaid, M.; Islam, M.S.; Saba, N.; Paridah, M.T.

2014-01-01

Highlights: • In-situ polymerization and solution casting method used to manufacture WPC. • In-situ WPC exhibited better properties compared to pure wood, 5% WPC and 20% WPC. • Lowest water absorption and least biodegradability shown by In-situ wood. - Abstract: In-situ polymerization and solution casting techniques are two effective methods to manufacture wood polymer composites (WPCs). In this study, wood polymer composites (WPCs) were manufactured from meranti sapwood by solution casting and in-situ polymerization process using methyl methacrylate (MMA) and epoxy matrix respectively. Physical, mechanical, and morphological characterizations of fabricated WPCs were then carried out to analyse their properties. Morphological properties of composites samples were analyzed through scanning electron microscopy (SEM). The result reveals that in-situ wood composite exhibited better properties compared to pure wood, 5% WPC and 20% WPC. Moreover, in-situ WPC had lowest water absorption and least biodegraded. Conversely, pure wood shown moderate mechanical strength, high biodegradation and water absorption rate. In term of biodegradation, earth-medium brought more severe effect than water in deteriorating the properties of the specimens

Significance of wood extractives for wood bonding.

Science.gov (United States)

Roffael, Edmone

2016-02-01

Wood contains primary extractives, which are present in all woods, and secondary extractives, which are confined in certain wood species. Extractives in wood play a major role in wood-bonding processes, as they can contribute to or determine the bonding relevant properties of wood such as acidity and wettability. Therefore, extractives play an immanent role in bonding of wood chips and wood fibres with common synthetic adhesives such as urea-formaldehyde-resins (UF-resins) and phenol-formaldehyde-resins (PF-resins). Extractives of high acidity accelerate the curing of acid curing UF-resins and decelerate bonding with alkaline hardening PF-resins. Water-soluble extractives like free sugars are detrimental for bonding of wood with cement. Polyphenolic extractives (tannins) can be used as a binder in the wood-based industry. Additionally, extractives in wood can react with formaldehyde and reduce the formaldehyde emission of wood-based panels. Moreover, some wood extractives are volatile organic compounds (VOC) and insofar also relevant to the emission of VOC from wood and wood-based panels.

PHYSICAL AND MECHANICAL PROPERTIES OF BLACK WOOD (EBONY AS A CONSTRUCTION MATERIAL

Directory of Open Access Journals (Sweden)

Fengky Satria Yoresta

2015-01-01

Full Text Available This research is aimed to determine physical and mechanical properties of Ebony wood as a construction material. The physical and mechanical properties test is conducted based on ASTM D 143-94 code. The mean value of moisture content and specific gravity of Ebony wood is obtained 12,90% and 0,92 gr.cm-3 respectively. Meanwhile MOE, bending strength, compressive strength parallel to grain, shear strength, and tensile strength parallel to grain are 180.425,87 kg.cm-2; 1656,22 kg.cm-2; 861,55 kg.cm-2; 119,61 kg.cm-2; dan 2.319,03 kg.cm-2 respectively. Based on the test results, it can be concluded that Ebony wood is classified to Strength Class I due to PKKI 1961, so it can be recommended for use in heavy construction such as bridge and building structures   Penelitian ini bertujuan menentukan sifat fisis dan mekanis kayu  Ebony sebagai material konstruksi. Pengujian sifat fisis dan mekanis dilakukan berdasarkan standar ASTM D 143-94. -3Nilai kadar air rata-rata kayu Ebony diperoleh sebesar 12,90% dan berat jenis 0,92 gr.cm . Sementara nilai rata-rata MOE, kuat lentur, kuat tekan sejajar serat, kuat geser, dan kuat tarik -2 -2 -2sejajar serat berturut-turut adalah 180.425,87 kg.cm ; 1656,22 kg.cm ; 861,55 kg.cm ; -2 -2119,61 kg.cm ; dan 2.319,03 kg.cm . Berdasarkan hasil penelitian dapat disimpulkan bahwa kayu Ebony tergolong kelas kuat I menurut PKKI 1961, sehingga dapat direkomendasikan untuk digunakan pada konstruksi-konstruksi berat seperti jembatan dan struktur bangunan.   REFERENCES Aghayere A & Jason V. 2007. Structural Wood Design: A Practice-Oriented Approach Using the ASD Method. John Wiley & Sons, Inc., New Jersey Boen T. 2009. Constructing Seismic Resistant Masonry Houses in Indonesia. United Nation. Chauf KA. 2005. Karakteristik Mekanik Kayu Kamper sebagai Bahan Konstruksi. Majalah Ilmiah MEKTEK . Vol 7 : 41-47. Dolan JD. 2004. Timber Structures. Pp 628-669 in Wai FC & Eric ML (Eds Handbook of Structural Engineering – 2nd

Understanding wood chemistry changes during biopulping

Science.gov (United States)

Chris Hunt; William Kenealy; Carl Houtman

2003-01-01

Biopulping is the process of pretreating chips with fungus before mechanical pulping, resulting in significant energy savings and sheet strength improvements. This work presents sugar analysis, methylene blue adsorption, and titration data suggesting an increase in acid group content in wood is common with biopulping treatment. Some discussion of possible mechanisms of...

Bio-Based Adhesives and Evaluation for Wood Composites Application

Directory of Open Access Journals (Sweden)

Fatemeh Ferdosian

2017-02-01

Full Text Available There has been a rapid growth in research and innovation of bio-based adhesives in the engineered wood product industry. This article reviews the recent research published over the last few decades on the synthesis of bio-adhesives derived from such renewable resources as lignin, starch, and plant proteins. The chemical structure of these biopolymers is described and discussed to highlight the active functional groups that are used in the synthesis of bio-adhesives. The potentials and drawbacks of each biomass are then discussed in detail; some methods have been suggested to modify their chemical structures and to improve their properties including water resistance and bonding strength for their ultimate application as wood adhesives. Moreover, this article includes discussion of techniques commonly used for evaluating the petroleum-based wood adhesives in terms of mechanical properties and penetration behavior, which are expected to be more widely applied to bio-based wood adhesives to better evaluate their prospect for wood composites application.

Concepts in the development of new accelerated test methods for wood decay

Science.gov (United States)

Darrel D. Nicholas; Douglas Crawford

2003-01-01

Efforts to develop new environmentally friendly wood preservatives are seriously handicapped by the extended time period required to carry out the evaluation needed to establish confidence in the long term performance of new preservative systems. Studies in our laboratory have shown that using strength loss as a measure of the extent of wood decay makes it possible to...

Wood chemistry symposium: from muka to lignin

Energy Technology Data Exchange (ETDEWEB)

MacLeod, M.

1979-01-01

The Canadian Wood Chemistry Symposium held during September, 1979, is reviewed. The chemical and physical explanations of delignification were debated. Problems of mechanical pulping include insufficient brightness, yellowing, and low strength relative to energy consumption. A session on chemicals, energy, and food from wood began with criteria for a viable project, which included adequate return on investment, modest capital investment requirements, identified pre-existing markets, and favorable thermodynamic balances. The pulp and paper industry should improve its methods of using bark and wood waste in direct combustion (by pre-drying wastes and improving furnace efficiency) rather than supporting oil-from-wood projects, since using a waste for fuel will free fossil fuels for uses in synthetic fibers and thermoplastics. In the area of food, there are modest successes with cellulose fiber additives to bread and snack food and single cell protein (which, though made from wastes, cannot compete with soy protein). However, making monomeric sugars from wood polysaccharides is not an efficient process, and muka, animal feed supplement from foliage, is successful only in Russia. In Canada it cannot compete with agricultural products. Alpha cellulose is a major wood chemical product. Promising uses include cellulose derived thermoplastics and lignosulphonates for secondary oil recovery. Instead of breaking wood polysaccharides and lignin into monomers and then repolymerizing them, it is possible to use the pre-built polymers; such an approach is illustrated by use of lignin in polyurethane foams, adhesives, and coatings.

EVALUATION OF CEMENT-BONDED PARTICLE BOARD PRODUCED FROM AFZELIA AFRICANA WOOD RESIDUES

Directory of Open Access Journals (Sweden)

OLUFEMI A. SOTANNDE

2012-12-01

Full Text Available The study was design to evaluate the physical and mechanical properties of cement-bonded particleboards produced from Afzelia africana wood residues. The production variables investigated were three wood particle types (flakes, flake-sawdust mix and sawdust, three chemical accelerators (CaCl2, MgCl2 and AlCl3 and four wood-cement ratios (1:2.0, 1:2.5, 1:3.0 and 1:3.5. The accelerators were based on 2% by weight of cement used. The boards produced were subjected to physical tests such as density, percentage water absorption and thickness swelling. Mechanical properties evaluated were modulus of rupture, internal bonding strength and compressive strength. The results revealed that the type of particle used, wood-cement ratio and chemical additives had a marked influence on the physical and mechanical properties of the boards (p < 0.05. From quality view point, flake-sawdust composite ranked best while flake boards ranked least. Similarly, CaCl2 had the best influence on the setting of the boards followed by MgCl2 and AlCl3. Finally, it has been shown that particle boards that satisfied the BISON type HZ requirement and ISO 8335 can be produced from Afzelia africana particularly at wood-cement of 1:2.5 and above.

Effect of activation on the porous structure and the strain and strength properties of beech wood biocarbon

Science.gov (United States)

Shpeizman, V. V.; Orlova, T. S.; Spitsyn, A. A.; Ponomarev, D. A.; Bogdanovich, N. I.; Martinez-Fernández, J.

2017-01-01

The effect of activation on the size, specific volume, and surface area of pores in a monolithic biomorphic material obtained by carbonization of beech wood is studied. It is shown that under optimal activation mode with a steam heated to 970°C, the total pore volume and surface, determined by adsorption curves, increased by 20 and 18 times, respectively. With the use of high-precision interferometric procedure, strain curves are obtained under uniaxial compression with a stepwise loading, and the strain rate is measured with a step of moving of 325 nm for activated and nonactivated samples. Despite an increase in porosity, the strength and maximum deformation of the samples do not decrease. The behavior of the strain rate jumps is analyzed in the micro- and nanometer range. It is shown that the maximum size of the micrometer jumps (4 μm) correlates well with the average size of the possible strain area in the samples (the average distance between the pores of small size), and the minimum dimensions of the strain jumps are close to the size of mesopores. Assessment of the strain change and its rate upon activation indicates that the effect of activation on the strain and strength characteristics is defined by nanometer defects, the most likely of which are microand mesopores.

Physical-mechanical and anatomical characterization in 26-year-old Eucalyptus resinifera wood

OpenAIRE

Lima,Israel Luiz de; Longui,Eduardo Luiz; Freitas,Miguel Luiz Menezes; Zanatto,Antonio Carlos Scatena; Zanata,Marcelo; Florsheim,Sandra Monteiro Borges; Bortoletto Jr.,Geraldo

2014-01-01

In the present study, we aimed to characterize Eucalyptus resinifera wood through physical and mechanical assays and wood anatomy studies, as well as determine the relationships between the properties and anatomy of wood. We used samples collected from the area close to the bark of ten 26-year-old E. resinifera trees. We concluded that the specific gravity (Gb), compression (f c0), and shear parallel to grain (f v0) were ranked in strength classes C30, C40 and C60, respectively, and that volu...

In situ polymerization of polyaniline in wood veneers.

Science.gov (United States)

Trey, Stacy; Jafarzadeh, Shadi; Johansson, Mats

2012-03-01

The present study describes the possibility to polymerize aniline within wood veneers to obtain a semi-conducting material with solid wood acting as the base template. It was determined that it is possible to synthesize the intrinsically conductive polymer (ICP) polyaniline in situ within the wood structure of Southern yellow pine veneers, combining the strength of the natural wood structure with the conductivity of the impregnated polymer. It was found that polyaniline is uniformly dispersed within the wood structure by light microscopy and FT-IR imaging. A weight percent gain in the range of 3-12 wt % was obtained with a preferential formation in the wood structure and cell wall, rather than in the lumen. The modified wood was found to be less hydrophilic with the addition of phosphate doped polyaniline as observed by equilibrium water swelling studies. While wood itself is insulating, the modified veneers had conductivities of 1 × 10(-4) to 1 × 10(-9) S cm(-1), demonstrating the ability to tune the conductivity and allowing for materials with a wide range of applications, from anti-static to charge-dispersing materials. Furthermore, the modified veneers had lower total and peak heat releases, as determined by cone calorimetry, because of the char properties of the ICP. This is of interest if these materials are to be used in building and furniture applications where flame retardance is of importance. © 2012 American Chemical Society

Strength and durability of one-part polyurethane adhesive bonds to wood

Science.gov (United States)

C. B. Vick; E. A. Okkonen

1998-01-01

One-part polyurethane wood adhesives comprise a new class of general purpose consumer products. Manufacturersa claims of waterproof bonds brought many inquiries to the Forest Products Laboratory (FPL) from users constructing aircraft, boats, lawn furniture, and other laminated materials for outdoor use. Although FPL has technical information on several types of...

Investigation of Miter Corner Joint Strength of Case Furniture from Particleboard

Directory of Open Access Journals (Sweden)

Valdas NORVYDAS

2012-12-01

Full Text Available Most pieces of case furniture (kitchen and bathroom furniture, cabinets, wardrobes, tables and etc. are made of 18 mm thick wood particle boards finished with various coatings. This three-layered constructional material is obtained by bonding wood particles of different fractions with synthetic resins using heating. The exploitation duration and quality of case furniture is determined by the mechanical properties of wood particle boards and the construction of joints of wood-based panels. On a frequent basis, pieces of case furniture with non-dismantable and dismantable construction are joined by using multidowel glued joints and cam connecting fittings intended for furniture, respectively. Wood-based panels can be joined with mitre joints whose mechanical properties have not undergone testing and comparison with regular joints when applying insertable wooden dowels or furniture connecting fittings. During the testing of particle board properties it was established that joining wood-based panels in this way ensures most efficient use of mechanical characteristics of the particleboard. In addition to the properties of the mitre joint, the tests also allowed determining the bending strength, tensile strength and bonding strength of the constructional material, and providing an original method for testing board properties, which can be successfully applied to the prediction of properties of the mitre joint. Tests were performed by using a universal tensile testing machine P-0.5. Joints were bonded by applying PVA dispersion. The surface of boards was veneered by using mahogany veneer and urea formaldehyde resin. It was found that mitre joints of wood particle boards can withstand loads that are higher from 2 to 4 times, in comparison to glued doweled joints or joints constructed with cam connecting fittings.DOI: http://dx.doi.org/10.5755/j01.ms.18.4.3095

Wood handbook : wood as an engineering material

Science.gov (United States)

Robert J. Ross; Forest Products Laboratory. USDA Forest Service.

2010-01-01

Summarizes information on wood as an engineering material. Presents properties of wood and wood-based products of particular concern to the architect and engineer. Includes discussion of designing with wood and wood-based products along with some pertinent uses.

Manufacturing of golf club using wood-plastic combination produced by γ-irradiation

International Nuclear Information System (INIS)

Yamagami, Masayuki; Tsujii, Yukio; Ohnishi, Tokuhiro; Miyoshi, Hirofumi; Chubachi, Mitsuo; Takada, Hisatoshi.

1992-01-01

Wood-plastic combination (WPC) was produced by γ-irradiation of persimmon impregnated with acrylonitrile and styrene. The hardness and strength of WPC obtained were higher than those of an unmodified wood. Thus, it was found that the WPC is suited for a head of golf club, because the Shore hardness value of WPC is 36% greater than that of unmodified wood. An impregnation method of monomers with some pigments could produce colored WPC without diminishing natural grain. Head of golf club could be manufactured from colored WPC in practice. (auhtor)

Properties of concretes and wood composites using a phosphate-based binder

Science.gov (United States)

Hong, Luong Thanh

Magnesium potassium phosphate ceramics are from the family of phosphate-based cements which can be used as alternatives to Portland cements. In this study, concretes and wood composites were produced using magnesium potassium phosphate ceramic binders and supplementary materials including fly ash, sand, silica fume and sawdust. Bentonite, Delvo Stabilizer and baking soda were used as additives to increase the workability and the setting time of the fresh mixutres and decrease the density of the hardened products. The materials were then reinforced with chopped glass-fibers or textile glass-fabrics to increase their hardened properties. At 50% fly ash by total mass of the binder, the concretes had compressive strength and density of 33 MPa and 2170 kg/m3, respectively, after 90 days of simple curing. At 20% fly ash by total mass of the binder, the wood composites had compressive strength and density of 13 MPa and 1320 kg/m3, respectively, after 90 days. The flexural strengths were about 10% to 47% of the corresponding cylinder compressive strengths for these mixes. Increases in both compressive and flexural strengths for these mixes were observed with the addition of chopped glass-fibers or textile glass-fabrics.

Property improvement by gamma polymerization of methyl methacrylate impregnated local Thai wood Yang (Dipterocarpus Sp.)

International Nuclear Information System (INIS)

Saisomboon, S.; Sumitra, T.

1990-01-01

Property improvement of a local Thai wood (Yang-Dipterocarpus Sp.) was studied by impregnating with methyl methacrylate before polymerizing with gamma ray. The polymer loading were 126 and 68 percent for sapwood and heart wood, respectively. Significant improvements in impact, compressive and bending strength were observed in the wood polymer composite (WPC). In addition, the microstructure and the impact fractured-surfaces of WPC were also carried with a scanning electron-microscope

WOOD PROPERTIES AND EFFECT OF WOOD PROPERTIES ON THE WOOD FINISHING

Directory of Open Access Journals (Sweden)

Abdulkadir Malkoçoğlu

2006-04-01

Full Text Available Wood is basic raw material for furniture and joinery industries with wood structures. Wood is a biological material that has widely different properties depending on species, geographic area where the tree grew, the growth condition, size of the tree at harvest, sawing, and other manufacturing processes. Wood properties have been characterized within two groups as natural and manufacturing factors that effects finishing performance. Grow rate, density, knots, moisture content, extractives and juvenile wood are natural characteristics. Grain orientation, texture, drying and performance expectations are manufacturing characteristics. In this review, the effects of natural and manufacturing characteristics are discussed on the surface finishing performance of wood.

Comparison of the compressive strength of impregnated and nonimpregnated eucalyptus subjected to two different pressures and impregnation times

Directory of Open Access Journals (Sweden)

Waldemir Rodrigues

2004-06-01

Full Text Available The durability of wood is affected by several factors. For this reason, much research has been done on a variety of chemical compounds for impregnating wood, aimed at preserving it while simultaneously improving its properties. Recent studies of the properties of impregnated wood have demonstrated the possibility of substantially improving its mechanical characteristics. Thus, the purpose of this work was to compare the strength to parallel compression of wooden fibers (Eucalyptus grandis, both nonimpregnated and impregnated with a monocomponent resin, from the standpoint of pressure and impregnation time, aiming at its structural utilization. The results demonstrate that the compressive strength of impregnated test specimens is greater than that of nonimpregnated ones, indicating that monocomponent polyurethane resin can be considered suitable for impregnating wood, since it increases the compressive strength of eucalyptus.

Wood : adhesives

Science.gov (United States)

A.H. Conner

2001-01-01

This chapter on wood adhesives includes: 1) Classification of wood adhesives 2) Thermosetting wood adhesives 3) Thermoplastic adhesives, 4) Wood adhesives based on natural sources 5) Nonconventional bonding of wood 6) Wood bonding.

Calcined clay lightweight ceramics made with wood sawdust and sodium silicate

Energy Technology Data Exchange (ETDEWEB)

Santis, Bruno Carlos de; Rossignolo, Joao Adriano, E-mail: desantis.bruno@gmail.com [Universidade de Sao Paulo (USP), Pirassununga, SP (Brazil); Morelli, Marcio Raymundo [Universidade Federal de Sao Carlos (UFSCar), SP (Brazil). Departamento de Engenharia de Materiais

2016-11-15

This paper aims to study the influence of including wood sawdust and sodium silicate in the production process of calcined clay lightweight ceramics. In the production process first, a sample used by a company that produces ceramic products in Brazil was collected. The sample was analysed by techniques of liquidity (LL) and plasticity (LP) limits, particle size analysis, specific mass, X-ray diffraction (XRD) and X ray fluorescence spectrometry (XRF). From the clay, specimens of pure clay and mixtures with wood sawdust (10%, 20% and 30% by mass) and sodium silicate were produced and fired at a temperature of 900 deg C. These specimens were submitted to tests of water absorption, porosity, specific mass and compressive strength. Results of this research indicate that the incorporation of wood sawdust and sodium silicate in the ceramic paste specimens can be useful to make calcined clay lightweight ceramics with special characteristics (low values of water absorption and specific mass and high values of compressive strength), which could be used to produce calcined clay lightweight aggregates to be used in structural concrete. (author)

Eco-friendly materials for large area piezoelectronics: self-oriented Rochelle salt in wood

Science.gov (United States)

Lemaire, E.; Ayela, C.; Atli, A.

2018-02-01

Upgraded biodegradable piezoelectric composite materials elaborated by incorporation of Rochelle salt (RS, Sodium potassium tartrate tetrahydrate) in wood were reported. RS crystals, known as the first discovered piezoelectric material, were grown in the micro-cavities of wood, having naturally a tubular structure, by soaking the wood into RS saturated water. Since most of the cavities in wood are oriented in the same direction, the piezoelectric effect was improved when the cavities were filled by RS crystals. The mechanical, structural and piezoelectric properties of RS incorporated wood composite samples were characterized. Both direct and converse piezoelectric effects are illustrated. The wood-base composite exhibits an effective piezoelectric constant d 33 of 11 pC N-1. Also, the flexural strength and modulus of elasticity were enhanced by inserting RS into the wood, nevertheless the samples became more brittle. The wood-based piezoelectric samples prepared in this work can be used as actuators, sensors or energy harvesters. The process developed here permits us to manufacture large area piezoelectric devices which are environmentally and economically unsurpassed.

Influence of Maleic Anhydride/Glycidyl Methacrylate Cografted Polylactic Acid on Properties of Wood Flour/PLA Composites

Directory of Open Access Journals (Sweden)

DU Jun

2017-12-01

Full Text Available Graft copolymers of PLA-g-MAH, PLA-g-GMA and PLA-co-MAH/GMA were prepared by means of melt grafting. The structure of the graft copolymers were characterized by FTIR.Wood flour/PLA composites were prepared by injection molding with three kinds of graft copolymers as compatibilizers, and the fractured morphology of composites was investigated by scanning electron microscope (SEM. Results show that there is no obvious phase interface between wood flour and PLA,which indicating the interfacial compatibility of wood flour/PLA composites is improved after adding different graft copolymers. The determination results of mechanical properties, processing flowability and dynamic rheological property of composites prepared with different graft copolymers reveal that, compared to the composite without compatibilizer, the tensile strength and impact strength of wood flour/PLA composites are increased by 9.54% and 7.23% respectively, and the equilibrium torque, shear heat, storage modulus and complex viscosity are all increased after adding maleic anhydride/glycidyl methacrylate cografted polylactic acid.

A NOVEL FIRE RETARDANT AFFECTS FIRE PERFORMANCE AND MECHANICAL PROPERTIES OF WOOD FLOUR-HIGH DENSITY POLYETHYLENE COMPOSITES

Directory of Open Access Journals (Sweden)

Mingzhu Pan,

2012-02-01

Full Text Available Wood flour-high density polyethylene (HDPE composites were prepared to investigate the effects of ammonium polyphosphate based fire retardant content (2, 4, 6, 8, and 10-wt%, on the flammability, mechanical, and morphological properties of the wood flour-HDPE composites in this study. Cone calorimetry analysis showed that the addition of fire retardant could decrease the heat release rate (HRR and total smoke release of wood flour-HDPE composites, while it had no obviously effects on effective heat of combustion. Most of the decrease of the HRR occurred with the concentration of the fire retardant up to 4-wt%. With addition of fire retardant, the composites showed a decrease in tensile elongation at break and impact strength, and had no obvious effect on tensile and flexural strength. The scanning electron microscopy observation on the fracture surface of the composites indicated that fire retardant had a uniform dispersion in the wood flour-HDPE composites. However, interfacial bonding would be suggested to improve in wood flour-HDPE composites with ammonium polyphosphate based fire retardant.

The effect of crosslinker on mechanical and morphological properties of tropical wood material composites

International Nuclear Information System (INIS)

Islam, Md. Saiful; Hamdan, Sinin; Rahman, Md. Rezaur; Jusoh, Ismail; Ahmed, Abu Saleh

2011-01-01

In this study, wood polymer composites (WPCs) based on five kinds of selected tropical wood species, namely Jelutong (Dyera costulata), Terbulan (Endospermum diadenum), Batai (Paraserianthes moluccana), Rubber (Hevea brasiliensis), and Pulai (Alstonia pneumatophora), were impregnated with methyl methacrylate (MMA) and hexamethylene diisocyanate (HMDIC) monomers mixture in the ratio of 1:1 for composite manufacturing. All these tropical wood reacted with hexamethylene diisocyanate and crosslinked with MMA which enhanced the hydrophobic (restrained water) nature of wood. The vacuum-pressure method was used to impregnate the samples with monomer mixture. The monomer mixture loading achievable was found to be dependent on the properties of wood species. Low loading was observed for the high density wood species. Mechanical strength of fabricated wood polymer composites (WPCs) in term of modulus of elasticity (MOE) and modulus of rupture (MOR) were found to be significantly improved. The wood-polymer interaction was confirmed by Fourier transform infrared (FTIR) spectroscopy. Morphological properties of raw wood and WPC samples were evaluated by scanning electron microscopy (SEM) and XRD analysis and an improvement in morphological properties was also observed for WPC.

Environmental assessment of domestic wood heating

International Nuclear Information System (INIS)

Labouze, E.; Le Guerin, Y.

2009-01-01

In France, more than 6 million families are concerned with the domestic use of wood energy. The wood energy plan of ADEME aims at encouraging the development of wood energy in three sectors: domestic, collective/tertiary, industrial. In that context, ADEME commissioned BIO Intelligence Service a life cycle assessment of collective and industrial heating in order to give objective environmental information and to analyse the strength and weakness of wood heating. Three scenarios were defined according to the origin of wood: firewood, granules and sawmill chips. The study also proposes a comparison to other heating systems: gas, fuel oil and electricity. The life cycle analysis applied to domestic heating consists in quantifying the environmental impacts of the whole linked steps: extraction of fuel, distribution, final use... Every system under study has been divided according to three main stages: - Extraction of raw materials; - Transport of fuels until the place of storage or distribution; - Use (combustion or upstream production of energy in the case of electricity). The environmental impacts are estimated with the following indicators: - Non renewable primary energy balance sheet; - Global warming potential; - Air acidification potential; - Eutrophication potential; - Emissions of toxic metals in air and in soils. The results show that wood heating have the best energy and global warming balance sheets. For air acidification, the combustion stage is pre-dominant regardless of the energy resource. This is mainly due to nitrogen and sulphur oxides airborne emissions. For wood heating, preparation requires fuel consumption which also contributes significantly to nitrogen oxides emissions. The comparison with conventional energy shows that the wood scenarios are well positioned in relation to fuel and electricity for this indicator. Gas appears to be the best heating option for this indicator. The contribution eutrophication is also due to nitrogen oxides airborne

Facile synthesis of high strength hot-water wood extract films with oxygen-barrier performance

Science.gov (United States)

Chen, Ge-Gu; Fu, Gen-Que; Wang, Xiao-Jun; Gong, Xiao-Dong; Niu, Ya-Shuai; Peng, Feng; Yao, Chun-Li; Sun, Run-Cang

2017-01-01

Biobased nanocomposite films for food packaging with high mechanical strength and good oxygen-barrier performance were developed using a hot-water wood extract (HWE). In this work, a facile approach to produce HWE/montmorillonite (MMT) based nanocomposite films with excellent physical properties is described. The focus of this study was to determine the effects of the MMT content on the structure and mechanical properties of nanocomposites and the effects of carboxymethyl cellulose (CMC) on the physical properties of the HWE-MMT films. The experimental results suggested that the intercalation of HWE and CMC in montmorillonite could produce compact, robust films with a nacre-like structure and multifunctional characteristics. This results of this study showed that the mechanical properties of the film designated FCMC0.05 (91.5 MPa) were dramatically enhanced because the proportion of HWE, MMT and CMC was 1:1.5:0.05. In addition, the optimized films exhibited an oxygen permeability below 2.0 cm3 μm/day·m2·kPa, as well as good thermal stability due to the small amount of CMC. These results provide a comprehensive understanding for further development of high-performance nanocomposites which are based on natural polymers (HWE) and assembled layered clays (MMT). These films offer great potential in the field of sustainable packaging.

Analysis of the Strength of Timber and Glulam Timber Beams with Steel Reinforcement

Directory of Open Access Journals (Sweden)

Arie Putra Usman

2015-12-01

Full Text Available Indonesia is a tropical country with abundant tropical timber that can be used as a building material. Wood is a renewable material, thus making it an environmentally friendly construction material. However, the dimensional limitations of solid wood may pose problems in structural constructions. Wood material also has some disadvantages, such as brittle failure. However, the ductility of wood can be increased because of plasticity occurring in the compression zone. Wood material with good ductility can be obtained by reinforcing it in the tensile zone. This study is about the strength of wood material for use as a material for structural elements. Based on the analytical findings, the bending capacity of wood can be improved by adding reinforcements to the tensile zone.

Panel and planar experimental shear behavior of wood panels ...

African Journals Online (AJOL)

Panel shear strength along the thickness and planar shear along the length of wood panels laminated softwood oriented OSB 10 mm thick, conditioned at different moisture contents (anhydrous medium, ambient temperature and humid medium) was measured on standardized test specimens, cut in half lengthwise panel ...

Considerations in the weathering of wood-plastic composites

Science.gov (United States)

Nicole M. Stark

2007-01-01

During weathering, wood-plastic composites (WPCs) can fade and lose stiffness and strength. Weathering variables that induce these changes include exposure to UV light and water. Each variable degrades WPCs independently, but can also act synergistically. Recent efforts have highlighted the need to understand how WPCs weather, and to develop schemes for protection. The...

VARIATION IN THE FIBRE CHARACTERISTICS OF THE WOOD OF ...

African Journals Online (AJOL)

cani

The study investigated the fibre characteristics and chemical composition of Vitex doniana towards determining its potentials for pulp and paper. Fibre dimensions are of great importance because of the strong correlation between it and the strength properties of wood and paper. Axial and radial examinations of fibre ...

HIGH RESOLUTION MICROTOMOGRAPHY FOR DENSITY AND SPATIAL INFORMATION ABOUT WOOD STRUCTURES.

Energy Technology Data Exchange (ETDEWEB)

ILLMAN,B.

1999-07-22

Microtomography has successfully been used to characterize loss of structural integrity of wood. Tomographic images were generated with the newly developed third generation x-ray computed microtomography (XCMT) instrument at the X27A beamline at the National Synchrotron Light Source (NSLS). The beamline is equipped with high-flux x-ray monochromator based on multilayer optics developed for this application. The sample is mounted on a translation stage with which to center the sample rotation, a rotation stage to perform the rotation during data collection and a motorized goniometer head for small alignment motions. The absorption image is recorded by a single-crystal scintillator, an optical microscope and a cooled CCD array detector. Data reconstruction has provided three-dimensional geometry of the heterogeneous wood matrix in microtomographic images. Wood is a heterogeneous material composed of long lignocellulose vessels. Although wood is a strong natural product, fungi have evolved chemical systems that weaken the strength properties of wood by degrading structural vessels. Tomographic images with a resolution of three microns were obtained nonintrusively to characterize the compromised structural integrity of wood. Computational tools developed by Lindquist et al (1996) applied to characterize the microstructure of the tomographic volumes.

Cord Wood Testing in a Non-Catalytic Wood Stove

Energy Technology Data Exchange (ETDEWEB)

Butcher, T. [Brookhaven National Lab. (BNL), Upton, NY (United States); Trojanowski, R. [Brookhaven National Lab. (BNL), Upton, NY (United States); Wei, G. [Brookhaven National Lab. (BNL), Upton, NY (United States)

2014-06-30

EPA Method 28 and the current wood stove regulations have been in-place since 1988. Recently, EPA proposed an update to the existing NSPS for wood stove regulations which includes a plan to transition from the current crib wood fuel to cord wood fuel for certification testing. Cord wood is seen as generally more representative of field conditions while the crib wood is seen as more repeatable. In any change of certification test fuel, there are questions about the impact on measured results and the correlation between tests with the two different fuels. The purpose of the work reported here is to provide data on the performance of a noncatalytic stove with cord wood. The stove selected has previously been certified with crib wood which provides a basis for comparison with cord wood. Overall, particulate emissions were found to be considerably higher with cord wood.

Assessment of the wood waste resource and its position in the wood / wood-energy sector - Synthesis

International Nuclear Information System (INIS)

Guinard, Ludovic; Deroubaix, Gerard; Roux, Marie-Lise; Levet, Anne-Laure; Quint, Vincent

2015-04-01

The first objective of this study is to obtain a better knowledge of the 'wood wastes' issue, to propose a photography of the wood waste sector (productions, trades, consumptions), and then to elaborate different prospective scenarios on the use of wood waste volumes while taking into account possible evolutions on the medium or short term of the regulation and market of the wood/wood energy sector. The considered wastes come from industrial production, from the use of wood-based products, and from the end of life of products potentially containing wood. The authors present bibliographical sources and the adopted methodology, briefly describe the 'wood waste' system with its actors, and then report their assessment of wood wastes. They propose a global assessment as well as detailed assessments with respect to waste origins: wood trade and distribution, industries, craft, households and communities, building sector, public and private tertiary sector, packaging. They also address the collection and management of wood wastes by public services, and present the different types of valorisation (panel fabrication, energy, and others). They discuss exports, and then present different scenarios: a trend-based scenario, and two prospective scenarios with a priority to energetic valorisation or to material valorisation of wood wastes. These scenarios are compared

Characteristics and modeling of spruce wood under dynamic compression load; Charakteristik und Modellierung von Fichtenholz unter dynamischer Druckbelastung

Energy Technology Data Exchange (ETDEWEB)

Eisenacher, Germar

2014-01-28

Spruce wood is frequently used as an energy absorbing material in impact limiters of packages for the transportation of radioactive material. A 9m drop test onto an unyielding target is mandatory for the packages. The impact results in a dynamic compression load of the spruce wood inside the impact limiter. The lateral dilation of the wood is restrained thereby due to encasing steel sheets. This work's objective was to provide a material model for spruce wood based on experimental investigations to enable the calculation of such loading conditions. About 600 crush tests with cubical spruce wood specimens were performed to characterize the material. The compression was up to 70% and the material was assumed to be transversely isotropic. Particularly the lateral constraint showed to have an important effect: the material develops a high lateral dilation without lateral constraint. The force-displacement characteristics show a comparably low force level and no or only slight hardening. Distinctive softening occurs after the linear-elastic region when loaded parallel to the fiber. On the other hand, using a lateral constraint results in significantly higher general force levels, distinctive hardening and lateral forces. The softening effect when loaded parallel to the fiber is less distinctive. Strain rate and temperature raise or lower the strength level, which was quantified for the applicable ranges of impact limiters. The hypothesis of an uncoupled evolution of the yield surface was proposed based on the experimental findings. It postulates an independent strength evolution with deviatoric and volumetric deformation. The hypothesis could be established using the first modeling approach, the modified LS-DYNA material model MAT075. A transversely isotropic material model was developed based thereupon and implemented in LS-DYNA. The material characteristics of spruce wood were considered using a multi-surface yield criterion and a non-associated flow rule. The

Laboratory Investigation on Compressive Strength and Micro-structural Features of Foamed Concrete with Addition of Wood Ash and Silica Fume as a Cement Replacement

Directory of Open Access Journals (Sweden)

Othuman Mydin M.A.

2014-01-01

Full Text Available Wood Ash (WA and Silica Fume (SF exhibit good cementation properties and have great potential as supplementary binder materials for the concrete production industry. This study will focus on enhancing the micro-structural formation and compressive strength of foamed concrete with the addition of WA and SF. A total of 3 mixes were prepared with the addition of WA and SF at various cement replacement levels by total binder weight. For this particular study, the combination of WA (5%, 10%, and 15% by binder weight and SF (5%, 10%, and 15% by binder weight were utilized as supplementary binder materials to produce foamed concrete mixes. As was made evident from micrographs obtained in the study, the improvement observed in the compressive strength of the foamed concrete was due to a significant densification in the microstructure of the cement paste matrix in the presence of WA and SF hybrid supplementary binders. Experimental results indicated that the combination of 15% SF and 5% WA by binder weight had a more substantial influence on the compressive strength of foamed concrete compared to the control mix. Furthermore, the addition of WA and SF significantly prolonged the setting times of the blended cement paste of the foamed concrete.

Chapter 6: Wood energy and competing wood product markers

Science.gov (United States)

Kenneth E. Skog; Robert C. Abt; Karen Abt

2014-01-01

Understanding the effect of expanding wood energy markets is important to all wood-dependent industries and to policymakers debating the implementation of public programs to support the expansion of wood energy generation. A key factor in determining the feasibility of wood energy projects (e.g. wood boiler or pellet plant) is the long-term (i.e. 20-30year) supply...

Wood adhesives : vital for producing most wood products

Science.gov (United States)

Charles R. Frihart

2011-01-01

A main route for the efficient utilization of wood resources is to reduce wood to small pieces and then bond them together (Frihart and Hunt 2010). Although humankind has been bonding wood since early Egyptian civilizations, the quality and quantity of bonded wood products has increased dramatically over the past 100 years with the development of new adhesives and...

Tensile and impact properties of three-component PP/wood/elastomer composites

Directory of Open Access Journals (Sweden)

B. Pukanszky

2012-03-01

Full Text Available Polypropylene (PP was reinforced with wood flour and impact modified with elastomers to increase stiffness and impact resistance simultaneously. Elastomer content changed in four (0, 5, 10 and 20 wt%, while that of wood content in seven steps, the latter from 0 to 60 wt% in 10 wt% steps. Structure and adhesion were controlled by the addition of functionalized (maleated polymers. Composites were homogenized in a twin-screw extruder and then injection molded to tensile bars. Fracture resistance was characterized by standard and instrumented impact tests. The results showed that the components are dispersed independently of each other even when a functionalized elastomer is used for impact modification, at least under the conditions of this study. Impact resistance does not change much as a function of wood content in PP/wood composites, but decreases drastically from the very high level of the PP/elastomer blend to almost the same value obtained without impact modifier in the three-component materials. Increasing stiffness and fiber related local deformation processes led to small fracture toughness at large wood content. Micromechanical deformation processes depend mainly on the strength of PP/wood interaction; debonding and pull-out take place at poor adhesion, while fiber fracture dominates when adhesion is strong. Composites with sufficiently large impact resistance cannot be prepared in the usual range of wood contents (50–60 wt%.

Chapter 8: Soy Properties and Soy Wood Adhesives

Science.gov (United States)

Charles R. Frihart; Michael J. Birkeland

2014-01-01

Soy flour has been used for many years as a wood adhesive. Rapid development of petroleum-based infrastructure coupled with advancement of synthetic resin technology resulted in waning usage since the early 1960s. Discovery of using polyamidoamine–epichlorohydrin (PAE) resin as a co-reactant has been effective in increasing the wet bond strength of soy adhesives and...

Hydraulic and mechanical properties of young Norway spruce clones related to growth and wood structure

Science.gov (United States)

ROSNER, SABINE; KLEIN, ANDREA; MÜLLER, ULRICH; KARLSSON, BO

2011-01-01

Summary Stem segments of eight five-year-old Norway spruce (Picea abies (L.) Karst.) clones differing in growth characteristics were tested for maximum specific hydraulic conductivity (ks100), vulnerability to cavitation and behavior under mechanical stress. The vulnerability of the clones to cavitation was assessed by measuring the applied air pressure required to cause 12 and 50% loss of conductivity (Ψ12, Ψ50) and the percent loss of conductivity at 4 MPa applied air pressure (PLC4MPa). The bending strength and stiffness and the axial compression strength and stiffness of the same stem segments were measured to characterize wood mechanical properties. Growth ring width, wood density, latewood percentage, lumen diameter, cell wall thickness, tracheid length and pit dimensions of earlywood cells, spiral grain and microfibril angles were examined to identify structure–function relationships. High ks100 was strongly and positively related to spiral grain angle, which corresponded positively to tracheid length and pit dimensions. Spiral grain may reduce flow resistance of the bordered pits of the first earlywood tracheids, which are characterized by rounded tips and an equal distribution of pits along the entire length. Wood density was unrelated to hydraulic vulnerability parameters. Traits associated with higher hydraulic vulnerability were long tracheids, high latewood percentage and thick earlywood cell walls. The positive relationship between earlywood cell wall thickness and vulnerability to cavitation suggest that air seeding through the margo of bordered pits may occur in earlywood. There was a positive phenotypic and genotypic relationship between ks100 and PLC4MPa, and both parameters were positively related to tree growth rate. Variability in mechanical properties depended mostly on wood density, but also on the amount of compression wood. Accordingly, hydraulic conductivity and mechanical strength or stiffness showed no tradeoff. PMID:17472942

Synthesis and characterization of polypropylene/jigsaw wood ash composite

International Nuclear Information System (INIS)

Sudirman; Karo Karo, Aloma; Gunawan, Indra; Handayani, Ari; Hertinvyana, Evi

2002-01-01

The composite of polypropylene (PP) polymer with jigsaw wood ash as filler is the alternative composite material. The dispersion of the filler in the composite is random with the jigsaw wood ash composition of 10,30, and 50% by volume. The characterization of composite are done to measure its mechanical properties, physical properties and microstructure by using XRD and SEM. From this research, it is concluded that increasing filler content of the composite will decrease its mechanical and physical properties. The comparation of different composites are found that tensile strength of PP MF 10 is higher 4.24% compared with PP MF 2 as a matrix. It is also found that melting temperature of PP MF 10 is higher 4.09% compared with PP MF 2 as a matrices and the decomposition temperature different is 0.17%. The degree of crystallinity of composite with PP MF 10 as a matrices is 2.55% higher compared with PP MF 2. The higher degree of crystallinity is increasing the tensile strength

Some Properties of Astronium graveolens Wood Along the Stem

Directory of Open Access Journals (Sweden)

Eduardo Luiz Longui

Full Text Available ABSTRACT We investigated the axial variation of specific gravity, shear parallel to the grain and anatomical features of Astronium graveolens wood and related these properties to the anatomy along the stem. We felled five 20-year-old trees and cut discs from four different stem heights, including stem base, 1 meter, 2 meters and 3 meters, for a total of 20 discs, and studied wood samples near the bark and at the base of trunk. Axial variations found appear to provide a balance between mechanical strength of the wood at stem base by the higher density and higher shear by the increase in ray frequency that contributes to locking the vertical cells and growth rings, thus preventing the stem from easily breaking when bent. For hydraulic conductivity, vessels with smaller diameter and frequency at the stem base help prevent the occurrence of embolisms that would reduce water flow along the main stem.

Potential of Using Recycled Low-Density Polyethylene in Wood Composites Board

Directory of Open Access Journals (Sweden)

A. C. Igboanugo

2011-03-01

Full Text Available The aim of this study was to investigate the suitability of using recycled low density polyethylene (RLDPE in wood board manufacturing. The composite board was produced by compressive moulding by increasing the percentage LDPE from 30 to 50wt% with interval of 10wt% at a temperatures of 140 and 180oC, pressure of 30-40 Kg/cm2 and pressing time 7-13minutes. The microstructure and mechanical properties: modulus of rupture (MOR, modulus of elasticity (MOE, Tensile strength, impact strength properties of boards were determined. The results showed that high modulus of rupture of 20.31N/mm2and MOE of 1363N/mm2 were obtained from board produced at 140oC, 60/40wt% wood particles/LDPE content. The uniform distribution of the particles and the recycled LDPE in the microstructure of the composites board is the major factor responsible for the improvement in the mechanical properties. The results showed that the MOE, MOR meets the minimum requirements of the European standards, for general purpose. The boards produced had tensile strength that is within the requirement. Hence this LDPE can be used in board production for general purpose applications.

Wood

DEFF Research Database (Denmark)

Unterrainer, Walter

2014-01-01

come from? How is it harvested? How is it manufactured and treated ? How are the buildings detailed and protected against weather during construction to keep them dry and make them long-life ? In a period of climate change, forests are the last lungs of the planet to sequestrate CO2. Their global size......Wood – a sustainable building material ? For thousands of years and all over the planet, wood has been used as a building material and exciting architecture has been created in wood. The fantastic structural, physical and aesthetic properties of the material as well as the fact that wood...

Wood burning

Energy Technology Data Exchange (ETDEWEB)

Winkelmann, H

1955-01-01

Discussed are the use of wood as a fuel, the technique of wood combustion and the operation of wood-burning stoves for cooking and heating. In addition, there is a section which reviews the use of wood stoves in various countries and lists manufacturers of stoves, central heating furnaces and in some cases sawdust burners.

Wettability and Impact Performance of Wood Veneer/Polyester Composites

Directory of Open Access Journals (Sweden)

Shayesteh Haghdan

2015-07-01

Full Text Available Fiber-reinforced thermosetting composites have been of interest since the 1940s due to their ease of use in processing, fast curing times, and high specific stiffness and strength. While the use of plant fibers in a polyester matrix has been thoroughly studied, only limited information is available regarding using wood as reinforcement. In this study, composites of thin wood veneer and a polyester matrix were made and the difficulties in the lamination and curing processes were investigated. Sheets of Douglas fir, maple, and oak veneers using a catalyzed polyester resin were assembled as unidirectional, balanced, and unbalanced cross-ply laminates. These were compared to control specimens using glass fiber as reinforcement. The impact properties of the samples, with respect to the laminate thicknesses, were characterized using a drop-weight impact tester. The wettability and surface roughness of unsanded and sanded wood veneers were also investigated. Results showed that Douglas fir cross-ply laminates had an impact energy equivalent to glass fiber laminates, making them an interesting alternative to synthetic fiber composites. Wood/polyester laminates absorbed a considerable amount of energy through a higher number of fracture modes. The balanced lay-up limited twisting of the wood/polyester composites. The lowest contact angle and highest wettability were observed in unsanded Douglas fir veneers.

PHYSICAL AND MECHANICAL PROPERTIES OF JUVENILE Schizolobium amazonicum WOOD

Directory of Open Access Journals (Sweden)

Graziela Baptista Vidaurre

2018-03-01

Full Text Available ABSTRACT Growth in world demand for wood implies a search for new fast growing species with silvicultural potential, and in this scenario for native species such as Paricá . Thus, the objective of this study was determining the physical and mechanical wood properties of the Schizolobium amazonicum species (known as Paricá in Brazil. Trees were collected from commercial plantations located in the north of Brazil with ages of 5, 7, 9 and 11 years. Four logs from trees of each age in the longitudinal direction of the trees were obtained, and later a diametrical plank of each log was taken to manufacture the specimens which were used to evaluate some physical and mechanical properties of the wood. The basic density of Paricá was reduced in the basetop direction and no difference between the radial positions was observed, while the average basic density of this wood was characterized as low. The region close to the bark showed less longitudinal contraction and also greater homogeneity of this property along the trunk, while for tangential contraction the smallest variation was found in the region near the pith. Paricá wood contraction was characterized as low. Age influenced most of the mechanical properties, where logs from the base had the highest values of mechanical strength.

Variation in Wood Quality in White Spruce (Picea Glauca (Moench Voss. Part I. Defining the Juvenile–Mature Wood Transition Based on Tracheid Length

Directory of Open Access Journals (Sweden)

Cyriac Serge Mvolo

2015-01-01

Full Text Available Estimations of transition age (TA and juvenile wood proportion (JWP are important for wood industries due to their impact on end-product quality. However, the relationships between analytical determination of TA based on tracheid length (TL and recognized thresholds for adequate end products have not yet been established. In this study, we used three different statistical models to estimate TA in white spruce (Picea glauca (Moench Voss based on TL radial variation. We compared the results with technological maturity. A two-millimeter threshold, previously suggested for good paper tear strength, was used. Tracheid length increased from pith to bark and from breast height to upper height. Juvenile wood (JW was conical with the three models. At breast height, TA ranged from 11 to 27 years and JWP ranged from 15.3% to 47.5% across the three models. The linear mixed model produced more conservative estimates than the maximum-quadratic-linear (M_Q_L model. Both the linear mixed model and the M_Q_L model produced more conservative TA estimates than the piecewise model. TA estimates by the MIXED model, and to a lesser extent by the M_Q_L model, were equivalent to those for real mature wood, whereas TA estimates by the piecewise model were considerably lower, falling into the transition wood area.

EVOLUTION OF LIGHTWEIGHT WOOD COMPOSITES

Directory of Open Access Journals (Sweden)

Marius C. BARBU

2016-01-01

Full Text Available Lightweight boards and beams in the wood-based construction and furniture industry are not a new topic. The density reduction of panels using sandwich structure with light cores was confirmed by users like doors or mobile homes more than three decades ago. Today many ways to attain a lighter wooden structure are on offer, partially in industrial application. The first one is the use of light-weight wood species like balsa, lime, pine from southern hemisphere plantations etc. limited by the availability, strength properties, gluability and so on. A second one is the sandwich structure made from hard faces like thick veneer, thin plywood, particleboard or high density thin fiberboard and cores made from honeycomb paper, very light wood species or foams like the polystyrene one. A third way to produce a light structure is to reduce the core drastically, using predesigned skeletons with special shapes and connections to the faces. The engines for these developments are on the one hand the fast growing market of knockdown furniture and on the other hand the increasing costs for energy and raw materials. Additional factors that make weight saving a primary economical objective for most producers are transportation costs, easier handling and higher acceptance among the end users. Moreover, customers demand more for ergonomical solutions regarding packaging. Many patents were generated by researchers and developers for new one-stage production processes for sandwich panels with wood- and impregnated paper-based facings made from veneers, particles or fibres and a core consisting of expandable foams, particles or embedded hard skeletons. These ideas or prototypes could be integrated in existing continuous pressing lines for wood based panels keeping some of the advantages of the continuous production technique in matters of efficiency. Some of the challenges of the light weight wooden structure are the connection in half or final parts, resistance to

Competitive outcomes between wood-decaying fungi are altered in burnt wood.

Science.gov (United States)

Edman, Mattias; Eriksson, Anna-Maria

2016-06-01

Fire is an important disturbance agent in boreal forests where it creates a wide variety of charred and other types of heat-modified dead wood substrates, yet how these substrates affect fungal community structure and development within wood is poorly understood. We allowed six species of wood-decaying basidiomycetes to compete in pairs in wood-discs that were experimentally burnt before fungal inoculation. The outcomes of interactions in burnt wood differed from those in unburnt control wood for two species:Antrodia sinuosanever lost on burnt wood and won over its competitor in 67% of the trials compared to 40% losses and 20% wins on unburnt wood. In contrast, Ischnoderma benzoinumwon all interactions on unburnt wood compared to 33% on burnt wood. However, the responses differed depending on the identity of the competing species, suggesting an interaction between competitor and substrate type. The observed shift in competitive balance between fungal species probably results from chemical changes in burnt wood, but the underlying mechanism needs further investigation. Nevertheless, the results indicate that forest fires indirectly structure fungal communities by modifying dead wood, and highlight the importance of fire-affected dead wood substrates in boreal forests. © FEMS 2016. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

Rice straw-wood particle composite for sound absorbing wooden construction materials.

Science.gov (United States)

Yang, Han-Seung; Kim, Dae-Jun; Kim, Hyun-Joong

2003-01-01

In this study, rice straw-wood particle composite boards were manufactured as insulation boards using the method used in the wood-based panel industry. The raw material, rice straw, was chosen because of its availability. The manufacturing parameters were: a specific gravity of 0.4, 0.6, and 0.8, and a rice straw content (10/90, 20/80, and 30/70 weight of rice straw/wood particle) of 10, 20, and 30 wt.%. A commercial urea-formaldehyde adhesive was used as the composite binder, to achieve 140-290 psi of bending modulus of rupture (MOR) with 0.4 specific gravity, 700-900 psi of bending MOR with 0.6 specific gravity, and 1400-2900 psi of bending MOR with a 0.8 specific gravity. All of the composite boards were superior to insulation board in strength. Width and length of the rice straw particle did not affect the bending MOR. The composite boards made from a random cutting of rice straw and wood particles were the best and recommended for manufacturing processes. Sound absorption coefficients of the 0.4 and 0.6 specific gravity boards were higher than the other wood-based materials. The recommended properties of the rice straw-wood particle composite boards are described, to absorb noises, preserve the temperature of indoor living spaces, and to be able to partially or completely substitute for wood particleboard and insulation board in wooden constructions.

Application of photocuring technique on wood surface and its prospects in Bangladesh

International Nuclear Information System (INIS)

Bhattcacharia, S.K.; Khan, Mubarak A.

2005-01-01

Photocuring technique has unveiled a new horizon in polymer science. Application of photocuring technique on wood surface has enhanced the use of low grade wood. As Bangladesh is an overpopulated country, necessity of good quality wood is increasing day by day. So low grade wood, like Simul or Partex, locally produced particleboard, would come out with great use. As Partex board, produced from Jute sticks and various types of indigenous low grade wood and particle board are abundant in Bangladesh, so photocuring could play a major role to improve the quality of low grade wood and serve the nation. Already, a lot of research works were carried out by the local scientists to improve the wood surface using UV curing method. Different formulations were also developed by the local scientists using various oligomer, monomer and different types of additives. The used oligomers are epoxy, polyester, urethane, etc. and monomers of different functionalities and used additives are acrylic monomer, CaCO 3 , sand, MgSiO 3 , talc, etc. Thin films were prepared on glass plate with different formulations using UV radiation and different characteristics properties (pendulum hardness, abrasion, gloss (60 deg. and 20 deg.), microscratch hardness, weathering effect, adhesion strength, etc.) were studied. Now, a Pilot Plant has already been established with the financial assistance by the government of Bangladesh, worth US$ 3.5 million

Corn gluten meal as a biodegradable matrix material in wood fibre reinforced composites

International Nuclear Information System (INIS)

Beg, M.D.H.; Pickering, K.L.; Weal, S.J.

2005-01-01

This study was undertaken to investigate corn gluten meal (CGM) as a biodegradable matrix material for wood fibre reinforced composites. CGM was used alone, as well as hybridized with polypropylene, and reinforced with radiata pine (Pinus Radiata) fibre using a twin-screw extruder followed by injection moulding. Tensile testing, scanning electron microscopy and differential scanning calorimetry were carried out to assess the composites. For composites from CGM and wood fibres, extrusion was carried out with the aid of the following plasticizers: octanoic acid, glycerol, polyethylene glycol and water. Windows of processability for the different plasticizers were obtained for all plasticizers. These were found to lie between 20 and 50 wt.% of plasticizer with a maximum of approximately 20% wood fibre reinforcement. The best mechanical properties were obtained with a matrix containing 10 wt.% octanoic acid and 30 wt.% water, which gave a tensile strength and Young's modulus of 18.7 MPa and 4 GPa, respectively. Hybrid matrix composites were compounded with a maleated polypropylene coupling agent and benzoyl peroxide as a cross-linking agent. The highest tensile strength and Young's modulus obtained from hybrid matrix composites were 36.9 MPa and 5.8 GPa with 50 wt.% fibre

Potential wood protection strategies using physiological requirements of wood degrading fungi

NARCIS (Netherlands)

Sailer, M.F.; Etten, B.D. van

2004-01-01

Due to the increasing restrictions in the use of wood preserving biocides a number of potential biocide free wood preserving alternatives are currently assessed. Wood degrading fungi require certain conditions in the wood in order to be able to use wood as a food source. This paper discusses the

Wood Cellular Dendroclimatology: A Pilot Study on Bristlecone Pine in the Southwest US

Science.gov (United States)

Ziaco, E.; Biondi, F.; Heinrich, I.

2015-12-01

Tree-rings provide paleoclimatic records at annual to seasonal resolution for regions or periods with no instrumental climatic data. Relationships between climatic variability and wood cellular features allow for a more complete understanding of the physiological mechanisms that control the climatic response of trees. Given the increasing importance of wood anatomy as a source of dendroecological information, such studies are now starting in the US. We analyzed 10 cores of bristlecone pine (Pinus longaeva D.K. Bailey) from a high-elevation site included in the Nevada Climate-ecohydrological Assessment Network (NevCAN). Century-long chronologies (1870-2013) of wood anatomical parameters (lumen area, cell diameter, cell wall thickness) can be developed by capturing strongly contrasted microscopic images using a Confocal Laser Scanning Microscope, and then measuring cellular parameters with task-specific software. Measures of empirical signal strength were used to test the strength of the environmental information embedded in wood anatomy. Correlation functions between ring-width, cellular features, and PRISM climatic variables were produced for the period 1926-2013. Time series of anatomical features present lower autocorrelation compared to ring widths, highlighting the role of environmental conditions occurring at the time of cell formation. Mean chronologies of radial lumen length and cell diameter carry a stronger climatic signal compared to cell wall thickness, and are significantly correlated with climatic variables (maximum temperature and total precipitation) in spring (Mar-Apr) and during the growing season (Jun-Sep), whereas ring widths show weaker or no correlation. Wood anatomy holds great potential to refine dendroclimatic reconstructions at higher temporal resolution, providing better estimates of hydroclimatic variability and plant physiological adaptations in the southwest US.

MECHANICAL CHARACTERIZATION AND SHRINKAGE OF Sclerolobium paniculatum Vogel WOOD IN A HOMOGENEOUS PLANTING UNDER DIFFERENT LEVELS OF FERTILIZATION

Directory of Open Access Journals (Sweden)

Joselito Bonifácio Oliveira

2010-08-01

Full Text Available The purposa of this work was to study the influence of fertilization on wood quality of Sclerolobium paniculatum Vogel. A homogeneous planting trial, under different levels of liming and phosphorus, was established by Embrapa-Cerrados 18 years ago in Planaltina, Distrito Federal, Brazil, tropical wood savanna region. Mechanical tests conducted were static bending, parallel compression to grain, shear strength and shrinkage. No significant differences were observed for mechanical properties or for shrinkage, which presented: ¦b = 650kg/cm2, E = 59.877kg/cm2, ¦c = 296kg/cm2 e ¦n = 131kg/cm2. Control treatment showed highest values for shear strength and compression parallel to grain. Too many branches in all trees and also too many knots in lumber were observed. Pruning is recommended for homogeneous planting of Sclerolobium paniculatum to avoid knots in order to be produced wood of superior quality.

Effect of Weathering Time on the Physical - Mechanical Properties and Color Change in Wood Flour/HDPE Composite

Directory of Open Access Journals (Sweden)

Behzad Kord

2014-05-01

Full Text Available This study was carried out to investigate the effect of weathering time on the physical and mechanical properties and color change in composite made of wood flour and high density polyethylene (HDPE. For this purpose, wood flour and polyethylene at a weight ratio of 60:40 with coupling agent were compounded in an internal mixer, and the samples were made in injection molding. Then, the weathering process by ultraviolet irradiation and water spray was done on the samples at different times of 250, 500, 1000 and 2000 hours in accelerated weathering apparatus. Finally, the physical and mechanical properties and color measurement of samples were tested, and compared with control samples. Results indicated that the flexural strength, flexural modulus, tensile strength and tensile modulus decreased with an increase in weathering time; however, the water absorption increased. Also, the yellowness of wood plastic samples decreased with an increase in weathering time and due to the lightness and color change increased.

Eco-Friendly (Water Melon Peels: Alternatives to Wood-based Particleboard Composites

Directory of Open Access Journals (Sweden)

U. D. Idris

2011-12-01

Full Text Available The aim of this study was to investigate the suitability of using water melon peels as alternatives to wood-based particleboard composites. The water melon peels composite boards were produced by compressive moulding using recycled low density polyethylene (RLDPE as a binder. The RLDPE was varies from 30 to 70wt% with interval of 10wt%. The microstructure, water absorption(WA, thickness swelling index(TS, modulus of rupture (MOR, modulus of elasticity (MOE, internal bonding strength(IB, impact strength and wear properties of the boards were determined. The results showed that high modulus of rupture of 11.45N/mm2, MOE of 1678N/mm2, IB of 0.58N/mm2, wear rate of 0.31g were obtained from particleboard produced at 60wt%RLDPE. The uniform distribution of the water melon particles and the RLDPE in the microstructure of the composites board is the major factor responsible for the improvement in the mechanical properties. The results showed that the MOE, MOR and IB meet the minimum requirements of the European standards, for general purpose like panelling, ceiling, partitioning. Hence, water melon particles can be used as a substitute to wood-based particleboard for general purpose applications also besides being environmental friendly of using watermelon and RLDPE in production of particleboard, this alternative to wood-based particleboard is very cost-effective.

Can Acceptable Pulp be Obtained from Eucalyptus globulus Wood Chips after Hemicellulose Extraction?

OpenAIRE

Francisco López; M. Trinidad García; Vicente Mena; J. Mauricio Loaiza; Minerva A. M. Zamudio; Juan C. García

2014-01-01

This study investigates the operating conditions used in the soda-anthraquinone pulping of Eucalyptus globulus wood after autohydrolysis pretreatment on the yield, kappa number, and brightness of the resulting unbleached pulp. Moreover, strength-related properties of the resulting handsheets was examined to identify the best pulping conditions and compare the outcome with that of a conventional soda-anthraquinone pulping process. The paper strength properties of the pulp were similar to or be...

Wood Identification of 18th Century Furniture. Interpreting Wood Naming Inventoires

Directory of Open Access Journals (Sweden)

Rocio Astrid BERNAL

2011-09-01

Full Text Available The 18th century Portuguese church furniture represents an extraordinary richness recognised worldwide, which demands safeguarding and valorisation. The identification of the wood of furniture artworks is the most important component for its comprehension and preservation. In this work wood anatomical characters of an 18th century Portuguese decorative furniture set from the Colegiada de São Martinho de Cedofeita, in Porto, were analysed to identify the woods used for manufacturing and to clarify their common names. Furthermore, the objectives were to recognise some of the criteria for choice of wood as well as the source of each wood. The woods identified from 16 fragments belong to Apuleia sp., Acacia sp., Neolamarckia sp. and Castanea sativa. Apuleia sp. and Acacia sp. woods most likely arrived from Brazil, while the Neolamarckia sp. woods likely arrived from India and the C. sativa woods from Portugal. The results are in accordance with the known Portuguese colonial sea routes of the 15th -18th centuries. Interestingly the terms found in the inventories can refer to finishing methods instead to the name of the woods, as for instance “oil wood” can refer to “oiled wood” or “linseed oiled wood”. The species choice may be related to the mechanical properties of the wood as well as the original tree size. Two large planks of Acacia sp. were used for the top of the “Portuguese arcaz”, and Apuleia sp. was found on main structural elements of this set of furniture, suggesting that wood colour was also important. Woods from Neolamarckia sp. and C. sativa, were also identified, being Castanea wood present only in the most recent pieces of the furniture set.

Energy wood. Part 2b: Wood pellets and pellet space-heating systems

International Nuclear Information System (INIS)

Nussbaumer, T.

2002-01-01

The paper gives an overview on pellet utilization including all relevant process steps: Potential and properties of saw dust as raw material, pellet production with drying and pelletizing, standardization of wood pellets, storage and handling of pellets, combustion of wood pellets in stoves and boilers and applications for residential heating. In comparison to other wood fuels, wood pellets show several advantages: Low water content and high heating value, high energy density, and homogeneous properties thus enabling stationary combustion conditions. However, quality control is needed to ensure constant properties of the pellets and to avoid the utilization of contaminated raw materials for the pellet production. Typical data of efficiencies and emissions of pellet stoves and boilers are given and a life cycle analysis (LCA) of wood pellets in comparison to log wood and wood chips is described. The LCA shows that wood pellets are advantageous thanks to relatively low emissions. Hence, the utilization of wood pellet is proposed as a complementary technology to the combustion of wood chips and log wood. Finally, typical fuel cost of wood pellets in Switzerland are given and compared with light fuel oil. (author)

Wood-related occupations, wood dust exposure, and sinonasal cancer.

Science.gov (United States)

Hayes, R B; Gerin, M; Raatgever, J W; de Bruyn, A

1986-10-01

A case-control study was conducted to examine the relations between type of woodworking and the extent of wood dust exposure to the risks for specific histologic types of sinonasal cancer. In cooperation with the major treatment centers in the Netherlands, 116 male patients newly diagnosed between 1978 and 1981 with primary malignancies of epithelial origin of this site were identified for study. Living controls were selected from the municipal registries, and deceased controls were selected from the national death registry. Interviews were completed for 91 (78%) cases and 195 (75%) controls. Job histories were coded by industry and occupation. An index of exposure was developed to classify the extent of occupational exposure to wood dust. When necessary, adjustment was made for age and usual cigarette use. The risk for nasal adenocarcinoma was elevated by industry for the wood and paper industry (odds ratio (OR) = 11.9) and by occupation for those employed in furniture and cabinet making (OR = 139.8), in factory joinery and carpentry work (OR = 16.3), and in association with high-level wood dust exposure (OR = 26.3). Other types of nasal cancer were not found to be associated with wood-related industries or occupations. A moderate excess in risk for squamous cell cancer (OR = 2.5) was associated with low-level wood dust exposure; however, no dose-response relation was evident. The association between wood dust and adenocarcinoma was strongest for those employed in wood dust-related occupations between 1930 and 1941. The risk of adenocarcinoma did not appear to decrease for at least 15 years after termination of exposure to wood dust. No cases of nasal adenocarcinoma were observed in men whose first exposure to wood dust occurred after 1941.

Effect of carbon fiber addition on the electromagnetic shielding properties of carbon fiber/polyacrylamide/wood based fiberboards

Science.gov (United States)

Dang, Baokang; Chen, Yipeng; Yang, Ning; Chen, Bo; Sun, Qingfeng

2018-05-01

Carbon fiber (CF) reinforced polyacrylamide/wood fiber composite boards are fabricated by mechanical grind-assisted hot-pressing, and are used for electromagnetic interference (EMI) shielding. CF with an average diameter of 150 nm is distributed on wood fiber, which is then encased by polyacrylamide. The CF/polyacrylamide/wood fiber (CPW) composite exhibits an optimal EMI shielding effectiveness (SE) of 41.03 dB compared to that of polyacrylamide/wood fiber composite (0.41 dB), which meets the requirements of commercial merchandise. Meanwhile, the CPW composite also shows high mechanical strength. The maximum modulus of rupture (MOR) and modulus of elasticity (MOE) of CPW composites are 39.52 MPa and 5823.15 MPa, respectively. The MOR and MOE of CPW composites increased by 38% and 96%, respectively, compared to that of polyacrylamide/wood fiber composite (28.64 and 2967.35 MPa).

Bond Performance and Structural Characterization of Polysaccharide Wood Adhesive Made from Konjac Glucomannan/Chitosan/Polyvinyl Alcohol

Directory of Open Access Journals (Sweden)

Rong Gu

2016-08-01

Full Text Available The bond performance and bonding mechanism were evaluated for a Konjac glucomannan (KGM, Chitosan (CS, and polyvinyl alcohol (PVOH blended wood adhesive. An optimized experimental strategy was used to investigate the effects of the formula parameters of adhesives on the bonding strength of plywood using a Box-Behnken design and response surface methodology (RSM. The microstructure of the blended adhesives was analyzed by Fourier transform infrared spectroscopy (FTIR and scanning electron microscopy (SEM. An optimum bonding strength (3.42 ± 0.31 MPa was achieved with concentrations of KGM, CS, and 10% PVOH of 2.3%, 2.3%, and 5.0%, respectively. There was strong hydrogen bonding between the KGM, CS, and 10% PVOH adhesives and the interface. SEM observations indicated that the blended adhesive exhibited a net-like structure that increased the overall bonding strength. These results provided the scientific basis for the continual development of environmentally friendly wood adhesives and the improvement of processing conditions.

Preparation of Self Hardening-modelling Polyurethane for Wood Repairing and Cracks Injection

International Nuclear Information System (INIS)

Meligi, G.A.; Elnahas, H.H.; Ammar, A.H.

2014-01-01

Self hardening composite as a modelling clay was prepared from polyurethane, two parts (A) and (B) where (A) contains polyol (polyether), vinyl acetate versatic ester copolymer (VAcVe) and magnesium silicate or wood powder and (B) contains toluene diisocyanate (TDI) as a hardening agent. The two parts mixed thoroughly giving soft putty like feel, open working time 1-2 h and cures hard overnight (24 h full cure). Factors affecting working time and full cure were evaluated. Also, measurements of surface hardness, compressive strength, scanning electron microscopy (SEM), water absorption and effect of ionizing radiation were studied. The suggestion for using the prepared polyurethane composite as clay dries as hard as a rock in the field of wood repair and cracks injection for building walls were recommended. Keywords: Polyurethane, modelling clay, radiation, wood repair and cracks injection.

Wood pellet seminar

International Nuclear Information System (INIS)

Aarniala, M.; Puhakka, A.

2001-01-01

The objective of the wood pellet seminar, arranged by OPET Finland and North Karelia Polytechnic, was to deliver information on wood pellets, pellet burners and boilers, heating systems and building, as well as on the activities of wood energy advisors. The first day of the seminar consisted of presentations of equipment and products, and of advisory desks for builders. The second day of the seminar consisted of presentations held by wood pellet experts. Pellet markets, the economy and production, the development of the pellet markets and their problems (in Austria), the economy of heating of real estates by different fuel alternatives, the production, delivery and marketing of wood pellets, the utilization of wood pellet in different utilization sites, the use of wood pellets in detached houses, pellet burners and fireplaces, and conversion of communal real estate houses to use wood pellets were discussed in the presentations. The presentations held in the third day discussed the utilization of wood pellets in power plants, the regional promotion of the production and the use of pellets. The seminar consisted also of visits to pellet manufacturing plant and two pellet burning heating plants

Corn gluten meal as a biodegradable matrix material in wood fibre reinforced composites

Energy Technology Data Exchange (ETDEWEB)

Beg, M.D.H. [Department of Materials and Process Engineering, University of Waikato, Private Bag 3105, Hamilton (New Zealand); Pickering, K.L. [Department of Materials and Process Engineering, University of Waikato, Private Bag 3105, Hamilton (New Zealand)]. E-mail: klp@waikato.ac.nz; Weal, S.J. [Department of Materials and Process Engineering, University of Waikato, Private Bag 3105, Hamilton (New Zealand)

2005-12-05

This study was undertaken to investigate corn gluten meal (CGM) as a biodegradable matrix material for wood fibre reinforced composites. CGM was used alone, as well as hybridized with polypropylene, and reinforced with radiata pine (Pinus Radiata) fibre using a twin-screw extruder followed by injection moulding. Tensile testing, scanning electron microscopy and differential scanning calorimetry were carried out to assess the composites. For composites from CGM and wood fibres, extrusion was carried out with the aid of the following plasticizers: octanoic acid, glycerol, polyethylene glycol and water. Windows of processability for the different plasticizers were obtained for all plasticizers. These were found to lie between 20 and 50 wt.% of plasticizer with a maximum of approximately 20% wood fibre reinforcement. The best mechanical properties were obtained with a matrix containing 10 wt.% octanoic acid and 30 wt.% water, which gave a tensile strength and Young's modulus of 18.7 MPa and 4 GPa, respectively. Hybrid matrix composites were compounded with a maleated polypropylene coupling agent and benzoyl peroxide as a cross-linking agent. The highest tensile strength and Young's modulus obtained from hybrid matrix composites were 36.9 MPa and 5.8 GPa with 50 wt.% fibre.

Projected wood energy impact on US forest wood resources

Energy Technology Data Exchange (ETDEWEB)

Skog, K.E. [USDA Forest Service, Madison, WI (United States)

1993-12-31

The USDA Forest Service has developed long-term projections of wood energy use as part of a 1993 assessment of demand for and supply of resources from forest and range lands in the United States. To assess the impact of wood energy demand on timber resources, a market equilibrium model based on linear programming was developed to project residential, industrial, commercial, and utility wood energy use from various wood energy sources: roundwood from various land sources, primary wood products mill residue, other wood residue, and black liquor. Baseline projections are driven by projected price of fossil fuels compared to price of wood fuels and the projected increase in total energy use in various end uses. Wood energy use is projected to increase from 2.67 quad in 1986 to 3.5 quad in 2030 and 3.7 quad in 2040. This is less than the DOE National Energy Strategy projection of 5.5 quad in 2030. Wood energy from forest sources (roundwood) is projected to increase from 3.1 billion (10{sup 9}) ft{sup 3} in 1986 to 4.4. billion ft{sup 3} in 2030 and 4.8 billion ft{sup 3} in 2040 (88, 124 and 136 million m{sup 3}, respectively). This rate of increase of roundwood use for fuel -- 0.8 percent per year -- is virtually the same as the projected increase rate for roundwood for pulpwood. Pulpwood roundwood is projected to increase from 4.2 billion ft{sup 3} in 1986 to 6.0 billion ft{sup 3} in 2030 and 6.4 billion ft{sup 3} in 2040 (119, 170 and 183 million m{sup 3}, respectively).

Composite Preparation of Wood Dust-Polyester-Coconut Choir Fiber Mixture for Particle Board

International Nuclear Information System (INIS)

Danu, Sugiarto; Darsono; Padmono; Betty, Angesti

2002-01-01

Experiment on the use of γ-ray of Co 60 radiation has been used for curing of composite which made of wood dust, unsaturated polyester resin and coconut coir mixture. Composite was prepared by mixing of wood dust, polyester and coconut coir at a various mixture composition. Concentration of polyesters were 50, 55 and 60 % by weight based on saw dust and polyester mixture. Irradiation was conducted using 27,6 kCi acti vity Co 60 at a dose rate of 5 kGy/hrs and dose of 8, 10 and 12 kGy. Composite was also prepared conventionally by using peroxide catalyst. Parameters observed were density, pencil hardness and compression strength Experimental results showed that optimum condition wus achieved at irradiation dose of 12 kGy, polyester concentration of 60 % and coconut coir fiber of 4 %. In this condition, the density, hardness and compression strength were 1,115 g/cm 3, 5 Hand 6,815 kN/cm2 respectively. Density, hardness of composite prepared by radiation were almost the same whereas the compression strength was higher than that of composite prepared by conventional method

The Effect of Carbon Nanotubes on the Mechanical Properties of Wood Plastic Composites by Selective Laser Sintering

Directory of Open Access Journals (Sweden)

Yunhe Zhang

2017-12-01

Full Text Available Wood-plastic composites (WPCs made by selective laser sintering (SLS approach of 3D printing offer many advantages over single polymer materials, such as low cost, sustainability, and better sintering accuracy. However, WPCs made via SLS are too weak to have widespread applications. In order to increase the mechanical properties of WPCs, a novel type of WPCs containing 0, 0.05, 0.1 and 0.15 wt % carbon nanotubes (CNT, 14 wt % wood fibers, 86 wt % polyether sulfone (PES was manufactured via SLS. The experimental results showed that the addition of small amount of CNTs can significantly increase the mechanical properties of the wood/PES composite material. The tensile strength, bending strength, and elasticity modulus were 76.3%, 227.9%, and 128.7% higher with 0.1 wt % CNTs than those without CNTs. The mechanical properties of specimens first increased and then decreased with the addition of CNTs. The SEM results of the specimens’ fracture morphology indicate that the preferable bonding interfaces between wood flour grains and PES grains were achieved by adding CNTs to the composites. There are two reasons why the composites possessed superior mechanical properties: CNTs facilitate the laser sintering process of WPCs due to their thermal conductivities, and CNTs directly reinforce WPCs.

Assessment of covalent bond formation between coupling agents and wood by FTIR spectroscopy and pull strength tests

DEFF Research Database (Denmark)

Rasmussen, Jonas Stensgaard; Barsberg, Søren Talbro; Venås, Thomas Mark

2014-01-01

In the focus was the question whether metal alkoxide coupling agents – titanium, silane, and zirconium – form covalent bonds to wood and how they improve coating adhesion. In a previous work, a downshift of the lignin infrared (IR) band ∼1600 cm-1 was shown to be consistent with the formation...... of ether linkages between lignin and titanium coupling agent. In the present work, changes were found in the attenuated total reflectance-Fourier transform IR (ATR-FTIR) spectra of lignin and wood mixed with silane, and titanium coupling agents, and to a lesser extent for a zirconium coupling agent...

Finishing of wood

Science.gov (United States)

R. Sam Williams

1999-01-01

The primary function of any wood finish (paint, varnish, and stain, for example) is to protect the wood surface, help maintain a certain appearance, and provide a cleanable surface. Although wood can be used both outdoors and indoors without finishing, unfinished wood surfaces exposed to the weather change color, are roughened by photodegradation and surface checking,...

Wood fuels utilization in Central Europe - the wood fuels consumption and the targets of utilization

International Nuclear Information System (INIS)

Alakangas, E.

1999-01-01

Following subjects are discussed in this presentation: The share of bioenergy of the total energy consumption in EU region; the wood fuels consumption in EU region in 1995; the division of bioenergy utilization (households, wood- based district heating, wood consumption in industry, power generation from wood and residues, biofuels, biogas and sludges); wood fuels consumption in households in EU countries in 1995; wood consumption in France; the additional wood fuel consumption potential in France; Blan bois - wood energy program; French wood energy markets; German wood energy markets; energy consumption in Germany; wood consumption in Bavaria; the wood fuels potential in Bavaria; wood fuels consumption in households in Bavaria; wood fuels consumption for district heating in Bavaria; fuel prices in Bavaria; Environmental regulations in Germany; small boiler markets in Germany; Energy consumption in Austria; small-scale utilization of wood fuels; utilization of wood energy. (Slides, additional information from the author)

Possibilities for the Use of Wood Ashes in Agriculture

OpenAIRE

Barbara Symanowicz; Marcin Becher; Dawid Jaremko; Korneliusz Skwarek

2018-01-01

The aim of the study was to determine the agricultural usefulness of the ashes obtained following the combustion of wood of fourteen tree species (pear tree, apple tree, aspen, ash, alder, birch, poplar, hornbeam, pine, common walnut, oak, hazel, bird cherry and spruce) in home fireplaces. The following physical properties of the ashes were determined: colour, solubility, porosity, absorbability, compression strength, degree of fineness, moisture content and spreadability. In the ashes...

Wood construction and magnetic characteristics of impregnated type magnetic wood

International Nuclear Information System (INIS)

Oka, Hideo; Hojo, Atsushi; Seki, Kyoushiro; Takashiba, Toshio

2002-01-01

The results of experiments involving the AC and DC magnetic characteristics of impregnated type magnetic wood were studied by taking into consideration the wood construction and fiber direction. The experimental results show that the sufficient amount of impregnated magnetic fluid varies depending on the fiber direction and length, and the grain face of the wood material. The impregnated type magnetic wood sample that is fully impregnated by magnetic fluid has a 60% saturation magnetization compared to the saturation magnetization of magnetic fluid. Samples for which the wood fiber direction was the same as the direction of the magnetic path had a higher magnetization intensity and permeability

Wood preservatives and pressure-treated wood: considerations for historic-preservation projects

Science.gov (United States)

Ronald W. Anthony; Stan T. Lebow

2015-01-01

Wood, an abundant resource throughout most of the world, has been used as a building material for thousands of years. Many historic buildings have been built primarily of wood, and masonry and stone buildings generally have wood elements, both structural and architectural. As a biological material, wood is both remarkably complex and yet quite durable if well...

Physico-mechanical Properties of Electron Beam Irradiated Particle boards Based on Wood flour/ Polyethylene/Cement Kiln Dust Impregnated with Unsaturated Polyester

International Nuclear Information System (INIS)

Abdel-Rahman, H.A.; Khattab, M.M.; Ismail, M.R.

2010-01-01

Particle boards were fabricated by mixing wood flour (WF), low density polyethylene (LDPE) and cement kiln dust (CKD) under hot pressure; and then impregnated in unsaturated polyester resin. These impregnated particle boards were subjected to various doses of electron beam irradiation up to 50 kGy. The physico-mechanical properties were characterized in terms of flexural strength, impact strength, water absorption, thickness swelling, and the thermal stability. The results showed that the partial replacement of wood flour with cement kiln dust up to 20% by weight improved the values of flexural strength, and impact strength. However, the water absorption percentage and thickness swelling values decreased with increasing the CKD ratio up to 40%. Furthermore, the treatment with electron beam irradiation doses improved the physico-mechanical properties of the impregnated particle boards up to 50 kGy. The improved results were confirmed by scanning electron microscopy (SEM) and thermogravimetric analysis (TGA)

Integrated control of wood destroying basidiomycetes combining Cu-based wood preservatives and Trichoderma spp.

Science.gov (United States)

Ribera, Javier; Fink, Siegfried; Bas, Maria Del Carmen; Schwarze, Francis W M R

2017-01-01

The production of new generation of wood preservatives (without addition of a co-biocide) in combination with an exchange of wood poles on identical sites with high fungal inoculum, has resulted in an increase of premature failures of wood utility poles in the last decades. Wood destroying basidiomycetes inhabiting sites where poles have been installed, have developed resistance against wood preservatives. The objective of the in vitro studies was to identify a Trichoderma spp. with a highly antagonistic potential against wood destroying basidiomycetes that is capable of colonizing Cu-rich environments. For this purpose, the activity of five Trichoderma spp. on Cu-rich medium was evaluated according to its growth and sporulation rates. The influence of the selected Trichoderma spp. on wood colonization and degradation by five wood destroying basidiomycetes was quantitatively analyzed by means of dry weight loss of wood specimens. Furthermore, the preventative effect of the selected Trichoderma spp. in combination with four Cu-based preservatives was also examined by mass loss and histological changes in the wood specimens. Trichoderma harzianum (T-720) was considered the biocontrol agent with higher antagonistic potential to colonize Cu-rich environments (up to 0.1% CuSO4 amended medium). T. harzianum demonstrated significant preventative effect on wood specimens against four wood destroying basidiomycetes. The combined effect of T. harzianum and Cu-based wood preservatives demonstrated that after 9 months incubation with two wood destroying basidiomycetes, wood specimens treated with 3.8 kg m-3 copper-chromium had weight losses between 55-65%, whereas containers previously treated with T. harzianum had significantly lower weight losses (0-25%). Histological studies on one of the wood destroying basidiomycetes revealed typical decomposition of wood cells by brown-rot fungi in Cu-impregnated samples, that were notably absent in wood specimens previously exposed to T

Integrated control of wood destroying basidiomycetes combining Cu-based wood preservatives and Trichoderma spp.

Directory of Open Access Journals (Sweden)

Javier Ribera

Full Text Available The production of new generation of wood preservatives (without addition of a co-biocide in combination with an exchange of wood poles on identical sites with high fungal inoculum, has resulted in an increase of premature failures of wood utility poles in the last decades. Wood destroying basidiomycetes inhabiting sites where poles have been installed, have developed resistance against wood preservatives. The objective of the in vitro studies was to identify a Trichoderma spp. with a highly antagonistic potential against wood destroying basidiomycetes that is capable of colonizing Cu-rich environments. For this purpose, the activity of five Trichoderma spp. on Cu-rich medium was evaluated according to its growth and sporulation rates. The influence of the selected Trichoderma spp. on wood colonization and degradation by five wood destroying basidiomycetes was quantitatively analyzed by means of dry weight loss of wood specimens. Furthermore, the preventative effect of the selected Trichoderma spp. in combination with four Cu-based preservatives was also examined by mass loss and histological changes in the wood specimens. Trichoderma harzianum (T-720 was considered the biocontrol agent with higher antagonistic potential to colonize Cu-rich environments (up to 0.1% CuSO4 amended medium. T. harzianum demonstrated significant preventative effect on wood specimens against four wood destroying basidiomycetes. The combined effect of T. harzianum and Cu-based wood preservatives demonstrated that after 9 months incubation with two wood destroying basidiomycetes, wood specimens treated with 3.8 kg m-3 copper-chromium had weight losses between 55-65%, whereas containers previously treated with T. harzianum had significantly lower weight losses (0-25%. Histological studies on one of the wood destroying basidiomycetes revealed typical decomposition of wood cells by brown-rot fungi in Cu-impregnated samples, that were notably absent in wood specimens

Wood composites

Science.gov (United States)

Lars Berglund; Roger M. Rowell

2005-01-01

A composite can be defined as two or more elements held together by a matrix. By this definition, what we call “solid wood” is a composite. Solid wood is a three-dimensional composite composed of cellulose, hemicelluloses and lignin (with smaller amounts of inorganics and extractives), held together by a lignin matrix. The advantages of developing wood composites are (...

Bacteria in decomposing wood and their interactions with wood-decay fungi.

Science.gov (United States)

Johnston, Sarah R; Boddy, Lynne; Weightman, Andrew J

2016-11-01

The fungal community within dead wood has received considerable study, but far less attention has been paid to bacteria in the same habitat. Bacteria have long been known to inhabit decomposing wood, but much remains underexplored about their identity and ecology. Bacteria within the dead wood environment must interact with wood-decay fungi, but again, very little is known about the form this takes; there are indications of both antagonistic and beneficial interactions within this fungal microbiome. Fungi are hypothesised to play an important role in shaping bacterial communities in wood, and conversely, bacteria may affect wood-decay fungi in a variety of ways. This minireview considers what is currently known about bacteria in wood and their interactions with fungi, and proposes possible associations based on examples from other habitats. It aims to identify key knowledge gaps and pressing questions for future research. © FEMS 2016. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

Non_standard Wood

DEFF Research Database (Denmark)

Tamke, Martin

. Using parametric design tools and computer controlled production facilities Copenhagens Centre for IT and Architecture undertook a practice based research into performance based non-standard element design and mass customization techniques. In close cooperation with wood construction software......, but the integration of traditional wood craft techniques. The extensive use of self adjusting, load bearing wood-wood joints contributed to ease in production and assembly of a performance based architecture....

Thermal Properties of Wood-Plastic Composites Prepared from Hemicellulose-extracted Wood Flour

Directory of Open Access Journals (Sweden)

A.A. Enayati

2013-01-01

Full Text Available Hemicellulose of Southern Yellow Pine wood spices was extracted by pressurized hot water at three different temperatures: 140°C, 155°C and 170°C. Compounding with PP (polypropylene was performed by extrusion after preparing wood flour and sieving to determine its mesh size. The ratio of wood to polymer was 50:50 based on oven-dry weight of wood flour. All extraction treatments and control samples were compounded under two sets of conditions, without and with 2% MAPP as coupling agent. Injection molding was used to make tensile test samples (dogbone from the pellets made by extrusion. Thermal properties of wood-plastic composites were studied by TGA and DSC while the thermal stability of pretreated wood flours, PP and MAPP were studied by TGA as well. The greater weight loss of wood materials was an indication that higher treatment temperature increases the extractability of hemicellulose. The removal of hemicellulose by extraction improves thermal stability of wood flour, especially for extraction at 170°C. Wood-plastic composites made from extracted fibers at 170°C showed the highest thermal stability. Coupling agent did not have a significant effect on thermal stability but it improved the degree of crystallinity of the composites.Surface roughness of wood fiber increased after treatment. Extraction of hemicellulose increased the degree of crystallinity but it was not significant except for samples from treated wood flour at 170°C and with MAPP.

Lignin-Retaining Transparent Wood.

Science.gov (United States)

Li, Yuanyuan; Fu, Qiliang; Rojas, Ramiro; Yan, Min; Lawoko, Martin; Berglund, Lars

2017-09-11

Optically transparent wood, combining optical and mechanical performance, is an emerging new material for light-transmitting structures in buildings with the aim of reducing energy consumption. One of the main obstacles for transparent wood fabrication is delignification, where around 30 wt % of wood tissue is removed to reduce light absorption and refractive index mismatch. This step is time consuming and not environmentally benign. Moreover, lignin removal weakens the wood structure, limiting the fabrication of large structures. A green and industrially feasible method has now been developed to prepare transparent wood. Up to 80 wt % of lignin is preserved, leading to a stronger wood template compared to the delignified alternative. After polymer infiltration, a high-lignin-content transparent wood with transmittance of 83 %, haze of 75 %, thermal conductivity of 0.23 W mK -1 , and work-tofracture of 1.2 MJ m -3 (a magnitude higher than glass) was obtained. This transparent wood preparation method is efficient and applicable to various wood species. The transparent wood obtained shows potential for application in energy-saving buildings. © 2017 The Authors. Published by Wiley-VCH Verlag GmbH & Co. KGaA.

Span-Dependent Distributions of the Bending Strength of Spruce Timber

DEFF Research Database (Denmark)

Ditlevsen, Ove; Källsner, Bo

2005-01-01

Tests data of bending strengths of a large number of timber beams of different spans obtained at the Swedish Institute for Wood Technology Research reveal a statistical structure that can be represented in a simple probabilistic model of series system type. A particular feature of the data from one...

Mechanics of Wood Machining

CERN Document Server

Csanády, Etele

2013-01-01

Wood is one of the most valuable materials for mankind, and since our earliest days wood materials have been widely used. Today we have modern woodworking machine and tools; however, the raw wood materials available are continuously declining. Therefore we are forced to use this precious material more economically, reducing waste wherever possible. This new textbook on the “Mechanics of Wood Machining” combines the quantitative, mathematical analysis of the mechanisms of wood processing with practical recommendations and solutions. Bringing together materials from many sources, the book contains new theoretical and experimental approaches and offers a clear and systematic overview of the theory of wood cutting, thermal loading in wood-cutting tools, dynamic behaviour of tool and work piece, optimum choice of operational parameters and energy consumption, the wear process of the tools, and the general regularities of wood surface roughness. Diagrams are provided for the quick estimation of various process ...

On the role of CFRP reinforcement for wood beams stiffness

Science.gov (United States)

Ianasi, A. C.

2015-11-01

In recent years, carbon fiber composites have been increasingly used in different ways in reinforcing structural elements. Specifically, the use of composite materials as a reinforcement for wood beams under bending loads requires paying attention to several aspects of the problem such as the number of the composite layers applied on the wood beams. Study consolidation of composites revealed that they are made by bonding fibrous material impregnated with resin on the surface of various elements, to restore or increase the load carrying capacity (bending, cutting, compression or torque) without significant damage of their rigidity. Fibers used in building applications can be fiberglass, aramid or carbon. Items that can be strengthened are concrete, brick, wood, steel and stone, and in terms of structural beams, walls, columns and floors. This paper describes an experimental study which was designed to evaluate the effect of composite material on the stiffness of the wood beams. It proposes a summary of the fundamental principles of analysis of composite materials and the design and use. The type of reinforcement used on the beams is the carbon fiber reinforced polymer (CFRP) sheet and plates and also an epoxy resin for bonding all the elements. Structural epoxy resins remain the primary choice of adhesive to form the bond to fiber-reinforced plastics and are the generally accepted adhesives in bonded CFRP-wood connections. The advantages of using epoxy resin in comparison to common wood-laminating adhesives are their gap-filling qualities and the low clamping pressures that are required to form the bond between carbon fiber plates or sheets and the wood beams. Mechanical tests performed on the reinforced wood beams showed that CFRP materials may produce flexural displacement and lifting increases of the beams. Observations of the experimental load-displacement relationships showed that bending strength increased for wood beams reinforced with CFRP composite plates

Soil-wood interactions

NARCIS (Netherlands)

Wal, van der Annemieke; klein Gunnewiek, Paulien; Boer, de Wietse

2017-01-01

Wood-inhabiting fungi may affect soil fungal communities directly underneath decaying wood via their exploratory hyphae. In addition, differences in wood leachates between decaying tree species may influence soil fungal communities. We determined the composition of fungi in 4-yr old decaying logs

Tradeoffs between hydraulic and mechanical stress responses of mature Norway spruce trunk wood.

Science.gov (United States)

Rosner, Sabine; Klein, Andrea; Müller, Ulrich; Karlsson, Bo

2008-08-01

We tested the effects of growth characteristics and basic density on hydraulic and mechanical properties of mature Norway spruce (Picea abies (L.) Karst.) wood from six 24-year-old clones, grown on two sites in southern Sweden differing in water availability. Hydraulic parameters assessed were specific hydraulic conductivity at full saturation (ks100) and vulnerability to cavitation (Psi50), mechanical parameters included bending strength (sigma b), modulus of elasticity (MOE), compression strength (sigma a) and Young's modulus (E). Basic density, diameter at breast height, tree height, and hydraulic and mechanical parameters varied considerably among clones. Clonal means of hydraulic and mechanical properties were strongly related to basic density and to growth parameters across sites, especially to diameter at breast height. Compared with stem wood of slower growing clones, stem wood of rapidly growing clones had significantly lower basic density, lower sigma b, MOE, sigma a and E, was more vulnerable to cavitation, but had higher ks100. Basic density was negatively correlated to Psi50 and ks100. We therefore found a tradeoff between Psi50 and ks100. Clones with high basic density had significantly lower hydraulic vulnerability, but also lower hydraulic conductivity at full saturation and thus less rapid growth than clones with low basic density. This tradeoff involved a negative relationship between Psi50 and sigma b as well as MOE, and between ks100 and sigma b, MOE and sigma a. Basic density and Psi50 showed no site-specific differences, but tree height, diameter at breast height, ks100 and mechanical strength and stiffness were significantly lower at the drier site. Basic density had no influence on the site-dependent differences in hydraulic and mechanical properties, but was strongly negatively related to diameter at breast height. Selecting for growth may thus lead not only to a reduction in mechanical strength and stiffness but also to a reduction in

Wood energy-commercial applications

Science.gov (United States)

Kennel, R. P.

1978-01-01

Wood energy is being widely investigated in many areas of the country because of the many obvious benefits of wood fuel such as the low price per million Btus relative to coal, oil, and gas; the wide availability of noncommercial wood and the proven ability to harvest it; established technology which is reliable and free of pollution; renewable resources; better conservation for harvested land; and the potential for jobs creation. The Southeastern United States has a specific leadership role in wood energy based on its established forest products industry experience and the potential application of wood energy to other industries and institutions. Significant questions about the widespread usage of wood energy are being answered in demonstrations around the country as well as the Southeast in areas of wood storage and bulk handling; high capitalization costs for harvesting and combustion equipment; long term supply and demand contracts; and the economic feasibility of wood energy outside the forest products industry.

Resistência ao impacto da madeira de nogueira-pecã em diferentes condições de umidade Impact strength of nogueira-pecã wood on different moisture conditions

Directory of Open Access Journals (Sweden)

Rafael Beltrame

2012-09-01

Full Text Available Os estudos de resistência da madeira ao impacto referem-se à eficiência com que este material absorve energia de um impacto e dissipa-a sem danos a sua estrutura. Dessa forma, o objetivo deste estudo foi avaliar a influência do teor de umidade na resistência ao impacto da madeira de nogueira-pecã (Carya illinoinensis. Para tanto, foram utilizadas árvores procedentes de duas regiões fisiográficas do estado do Rio Grande do Sul. Os corpos de prova, em condições de equilíbrio a 12% de umidade e saturados, foram submetidos ao impacto utilizando-se pêndulo de CHARPY, e avaliados quanto à resistência oferecida com a aplicação da carga nos planos tangencial e radial e posições de retirada (medula - casca nas toras, para as duas regiões fisiográficas em cada condição de umidade. Para auxiliar na interpretação dos dados, determinou-se a massa específica aparente a 12% e saturada, trabalho absorvido, coeficiente de resiliência e a cota dinâmica. Pôde-se verificar, por meio dos resultados, que a madeira de nogueira-pecã é mais resistente ao impacto na condição saturada.The studies of wood impact strength refers to the efficiency of this material in absorb impact energy and dissipate it without structural damages. The present study aimed to evaluate the influence of moisture content on the impact strength of nogueira-pecã (Carya illinoinensis wood. For this, trees from two physiographic regions of state of Rio Grande do Sul were used. The samples, stabilized at 12% of moisture content and in green conditions (saturated, were submitted to impact tests through a CHARPY pendulum, and were evaluated for the resistance to the application of loads in the tangential and radial sections, and in the positions of the log (pith-bark for the two physiographic regions at each moisture condition. Moreover, the apparent specific gravity at 12% and in green conditions (saturated, the absorbed work, the resilience coefficient and the

INFLUENCE OF ANATOMICAL FEATURES AND EXTRACTIVES CONTENT WOOD OF Eucalyptus grandis W. Hill ex Maiden IN QUALITY BONDING

Directory of Open Access Journals (Sweden)

Vanessa Cristina do Sacramento Albino

2012-12-01

Full Text Available http://dx.doi.org/10.5902/198050987561The study aimed to anatomically characterize and to quantify the total extractives in different positions of the log of Eucalyptus grandis W. Hill ex Maiden with 18 years of age and to assess their influence on the shear strength and percentage of wood failure in adhesive bonded joints with thermosetting resorcinol-formaldehyde. Histological slides were prepared for an anatomical study and determined the total extractive content. The preparation of bonded joints was made according to ASTM D 2339-98(2000. It was used the correlation coefficient of Pearson, 1% probability by t test to evaluate the correlation between the anatomical and extractives content with the quality of the glued joints. It was found that there was a correlation between the shear strength with the following characteristics: vessel diameter, wall width, length and width of the fiber, the width of the radius and total extractives content. For the percentage of wood failure, there was a correlation between this with the following characteristics: the frequency of vessels, thickness of the heat of fiber, and high frequency of lightning. Both the radial direction as in the longitudinal direction of the logs there was change in the values found for the measurement of the anatomical elements, the total amount of extractives, the shear test strength and the percentage of wood failure.

Who's Counting Dead Wood ?

OpenAIRE

Woodall, C. W.; Verkerk, H.; Rondeux, Jacques; Ståhl, G.

2009-01-01

Dead wood in forests is a critical component of biodiversity, carbon and nutrient cycles, stand structure, and fuel loadings. Until recently, very few countries have conducted systematic inventories of dead wood resources across their forest lands. This may be changing as an increasing number of countries implement dead wood inventories. A recent survey looks at the status and attributes of forest dead wood inventories in over 60 countries. About 13 percent of countries inventory dead wood gl...

Occurrence patterns of dead wood and wood-dependent lichens in managed boreal forest landscapes

OpenAIRE

Svensson, Måns

2013-01-01

Dead wood is a key resource for biodiversity, on which thousands of forest organisms are dependent. Because of current forest management, there has been a large-scale change in dead wood amounts and qualities, and consequently, many wood-dependent species are threatened. The general aim of this thesis is to increase our understanding of habitat requirements and occurrence patterns of wood-dependent lichens in managed, boreal forest landscapes. We surveyed dead wood and wood-dependent lichens ...

Production of wood pellets. Influence of additives on production, quality, storage, combustion and life cycle analysis of wood pellets; Herstellung von Holzpellets. Einfluss von Presshilfsmitteln auf Produktion, Qualitaet, Lagerung, Verbrennung sowie Energie- und Oekobilanz von Holzpellets

Energy Technology Data Exchange (ETDEWEB)

Hasler, P.; Nussbaumer, T. [Verenum, Zuerich (Switzerland); Buerli, J. [Buerli Pellets, Willisau (Switzerland)

2001-07-01

This report for the Swiss Federal Office of Energy (SFOE) presents the results of a study concerning the influence of additives on the various factors related to the manufacture of wood pellets and their use. Results of tests concerning the production, storage and combustion of wood pellets with and without additives are presented. Process modifications are discussed. The report shows that for all investigated additives neither energy consumption nor pellet throughput was improved. The influence of additives on the mechanical strength of the pellets is discussed, as are the combustion characteristics of the pellets, which emit significantly lower levels of NO{sub x} and particulate matter than typical wood chips. The authors recommend the application of advanced control technology to ensure optimum combustion conditions. A life-cycle analysis is presented which shows that pellets are ecologically more favourable than wood chips. The ecological potential for improvement in the manufacturing process is discussed, including emission reductions and heat recovery.

Energy from wood - an overview

International Nuclear Information System (INIS)

Nussbaumer, T.

2000-01-01

The present publication is the introduction to a series of papers on fundamentals and applications of wood energy. It summarizes figures and data of the actual situation of fuel wood utilization in Switzerland and its potential for the future. Further, the advantages of bio-energy are discussed and the possibilities of funding for bio-energy in Switzerland are described. Wood contributes with 2.5% to the total energy demand in Switzerland nowadays. However, the utilization of wood energy can be more than doubled, which is one of the targets of the Swiss energy policy. The supply chains for the different types of fuel wood are described and specifications and prices of log wood, forestry wood chips and wood residues are presented. The main applications of wood energy are residential heating with manually operated wood boilers and stoves, on the one hand, and heat production with automatic wood furnaces in industry and communities, on the other hand. Automatic furnaces have been promoted in the past ten years and hence they contribute nowadays with more than 50% to the energy supply from wood with a further growing share. As an assistance for further information, a list of institutions and addresses in the field of wood energy in Switzerland is given in the paper. (author)

Wood preservative testing

Science.gov (United States)

Rebecca Ibach; Stan T. Lebow

2012-01-01

Most wood species used in commercial and residential construction have little natural biological durability and will suffer from biodeterioration when exposed to moisture. Historically, this problem has been overcome by treating wood for outdoor use with toxic wood preservatives. As societal acceptance of chemical use changes, there is continual pressure to develop and...

Wood Dust

Science.gov (United States)

Learn about wood dust, which can raise the risk of cancers of the paranasal sinuses and nasal cavity. High amounts of wood dust are produced in sawmills, and in the furniture-making, cabinet-making, and carpentry industries.

Wood Smoke

Science.gov (United States)

Smoke is made up of a complex mixture of gases and fine, microscopic particles produced when wood and other organic matter burn. The biggest health threat from wood smoke comes from fine particles (also called particulate matter).

14 CFR 29.613 - Material strength properties and design values.

Science.gov (United States)

2010-01-01

... Administrator: (1) MIL—HDBK-5, “Metallic Materials and Elements for Flight Vehicle Structure”. (2) MIL—HDBK-17, “Plastics for Flight Vehicles”. (3) ANC-18, “Design of Wood Aircraft Structures”. (4) MIL—HDBK-23... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Material strength properties and design...

14 CFR 27.613 - Material strength properties and design values.

Science.gov (United States)

2010-01-01

... Administrator: (1) MIL-HDBK-5, “Metallic Materials and Elements for Flight Vehicle Structure”. (2) MIL-HDBK-17, “Plastics for Flight Vehicles”. (3) ANC-18, “Design of Wood Aircraft Structures”. (4) MIL-HDBK-23... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Material strength properties and design...

Wood thermoplastic composites

Science.gov (United States)

Daniel F. Caulfield; Craig Clemons; Roger M. Rowell

2010-01-01

The wood industry can expand into new sustainable markets with the formation of a new class of composites with the marriage of the wood industry and the plastics industry. The wood component, usually a flour or fiber, is combined with a thermoplastic to form an extrudable, injectable or thermoformable composite that can be used in many non-structural applications....

Mechanical and natural durability properties of wood treated with a novel organic preservative/consolidant product

International Nuclear Information System (INIS)

Lionetto, Francesca; Frigione, Mariaenrica

2009-01-01

An organic preservative/consolidant of new formulation was selected in order to evaluate its effect on the mechanical properties of worm-eaten walnut wood. Walnut wood is widely used for the realization of artistic handworks (e.g. statues, altars, etc.) furniture and flooring. The flexural strength and modulus of elasticity, the toughness and the hardness were determined on both treated and untreated samples. The experimental results showed that the product increased significantly the flexural strength while the other mechanical properties were not appreciably affected by the chemical treatment. The microstructure of the samples tested was observed using scanning electron microscopy. The preserving character against insects of the investigated product was assessed by both visual inspection and measurements of weight loss on the treated specimens after their exposure to living insects. The samples on which the product was applied, exposed to Oligomerus ptilinoides for one year, were more resistant to decay than the corresponding untreated samples.

How spectroscopy and microspectroscopy of degraded wood contribute to understand fungal wood decay.

Science.gov (United States)

Fackler, Karin; Schwanninger, Manfred

2012-11-01

Nuclear magnetic resonance, mid and near infrared, and ultra violet (UV) spectra of wood contain information on its chemistry and composition. When solid wood samples are analysed, information on the molecular structure of the lignocellulose complex of wood e.g. crystallinity of polysaccharides and the orientation of the polymers in wood cell walls can also be gained. UV and infrared spectroscopy allow also for spatially resolved spectroscopy, and state-of-the-art mapping and imaging systems have been able to provide local information on wood chemistry and structure at the level of wood cells (with IR) or cell wall layers (with UV). During the last decades, these methods have also proven useful to follow alterations of the composition, chemistry and physics of the substrate wood after fungi had grown on it as well as changes of the interactions between the wood polymers within the lignocellulose complex caused by decay fungi. This review provides an overview on how molecular spectroscopic methods could contribute to understand these degradation processes and were able to characterise and localise fungal wood decay in its various stages starting from the incipient and early ones even if the major share of research focussed on advanced decay. Practical issues such as requirements in terms of sample preparation and sample form and present examples of optimised data analysis will also be addressed to be able to detect and characterise the generally highly variable microbial degradation processes within their highly variable substrate wood.

Mechanical trunk in pine wood for cattle

Directory of Open Access Journals (Sweden)

Antonio Orlando da Luz Freire Neto

2012-12-01

Full Text Available The timber reforestation, mainly by Eucalyptus and Pinus sp., has low power processing, strength, good natural durability and, most importantly, provide reduce pressure on native forests. The concern with native forests and the high price of some of these woods force the market to replace those species by other, more abundant and available at most competitive prices. Anything that involves the handling of animals in its various phases has a direct dependency of husbandry facilities, pastures and actions of the people involved (best practices. With the segment of the production and export of meat increasingly competitive and globalized world, the adoption of best practices and animal welfare criteria are striking and decision makers for the acceptance of Brazilian beef in the world market, especially the European market. The use of appropriate animal husbandry facilities is critical to the proper rational management ("action with knowledge" of animals and increased productivity. The trunk restraint carries important role in the implementation and conduct of good animal welfare as having desirable features strength, durability, ability to contain cattle of various sizes, as well as easy to manipulate when the animal inside. Available on the market in the form of different models and costs, is an installation manufactured in wood and iron or galvanized, and may or may not be coupled with an analytical balance or digital, still and mechanical and other systems or electronics. The concern in this installation is perceived improvement in the number of patents filed and recorded and the constant evolution of their functions, with various companies operating in this segment. However, the development and validation of containment trunks with alternative materials, reflecting mainly the reduction of the final cost are poorly studied. In this first phase of the project will be considered the construction of trunk restraint coupled with analytical balance

In vitro wood decay of teak (Tectona grandis by Rigidoporus cf. microporus (Meripiliaceae, Polyporales, Basidiomycota

Directory of Open Access Journals (Sweden)

E. Sarmiento S

2016-03-01

Full Text Available The use of exotic species like teak for industry demands has increased over the last decades in Central America, however its vulnerability to decay by saprophytic fungi has not been well studied. Among these fungi, Rigidoporus spp. have been described as white rotters of dead hardwoods and conifers worldwide. In Costa Rica, R. microporus has been found growing on teak stumps. The aim of this study was to determine the effects of this white rot fungus on the chemical, mechanical and physical properties of teak wood from trees of different ages. Six and ten year old sapwood and heartwood samples were used in the assays. Severe anatomical damage and the highest weight and resistance losses were observed on 6 yr. old sapwood samples. There was an increase in the quantity of soluble materials in 1% NaOH (relative values and lignin content in all the samples analyzed, after 3 months exposure and up to the end of the experiment. Mass loss reduction and increased resistance of wood to compressive strength parallel to the grain were related to both the type of wood and the age of the tree. Knowledge of the potential damage that this fungus can cause to teak wood might help in a better selection of wood and developing more effective protection measures against decay in the field or in construction wood.

Wind pressure testing of tornado safe room components made from wood

Science.gov (United States)

Robert Falk; Deepak Shrestha

2016-01-01

To evaluate the ability of a wood tornado safe room to resist wind pressures produced by a tornado, two safe room com-ponents were tested for wind pressure strength. A tornado safe room ceiling panel and door were static-pressure-tested according to ASTM E 330 using a vacuum test system. Re-sults indicate that the panels had load capacities from 2.4 to 3.5 times that...

Life cycle environmental impacts of different construction wood waste and wood packaging waste processing methods

OpenAIRE

Manninen, Kaisa; Judl, Jáchym; Myllymaa, Tuuli

2016-01-01

This study compared the life cycle environmental impacts of different wood waste processing methods in three impact categories: climate impact, acidification impacts and eutrophication impacts. The wood waste recovery methods examined were the use of wood waste in terrace boards made out of wood composite which replace impregnated terrace boards, incineration of wood waste in a multi-fuel boiler instead of peat and the use of wood waste in the production of particleboard in either Finland or ...

Mathematical Simulation of Temperature Profiles within Microwave Heated Wood Made for Wood-Based Nano composites

International Nuclear Information System (INIS)

Li, X.; He, X.; Lv, J.; Wu, Y.; Luo, Y.; Chen, H.

2013-01-01

High intensive microwave pretreatment is a new method to modify wood for the fabrication of wood-based nano composites. Based on the physical law on heat transfer, a mathematical model to describe the temperature profiles within wood heated by high intensive microwave was established and simulated in this research. The results showed that the temperature profiles within wood were related to microwave heating methods; The temperature inside wood firstly increased and then gradually decreased along the direction of microwave transmission when the unilateral microwave heating was applied, and the temperature difference along the thickness direction of wood was very significant; The temperature with wood firstly increased and then gradually decreased from the wood surface to interior when the bilateral microwave heating was applied. Compared with the unilateral microwave heating, bilateral microwave heating is a better microwave heating method for the more uniform wood microwave pretreatment.

Many Roles of Wood Adhesives

Science.gov (United States)

Charles R. Frihart

2014-01-01

Although wood bonding is one of the oldest applications of adhesives, going back to early recorded history (1), some aspects of wood bonds are still not fully understood. Most books in the general area of adhesives and adhesion do not cover wood bonding. However, a clearer understanding of wood bonding and wood adhesives can lead to improved products. This is important...

Urban Wood Waste Resource Assessment

Energy Technology Data Exchange (ETDEWEB)

Wiltsee, G.

1998-11-20

This study collected and analyzed data on urban wood waste resources in 30 randomly selected metropolitan areas in the United States. Three major categories wood wastes disposed with, or recovered from, the municipal solid waste stream; industrial wood wastes such as wood scraps and sawdust from pallet recycling, woodworking shops, and lumberyards; and wood in construction/demolition and land clearing debris.

Strategi Pemasaran Mebel Kayu Sentra Industri Kecil Pondok Bambu, Jakarta Timur (Wood Furniture Marketing Strategy on Pondok Bambu Small Industry Centre, East Jakarta

Directory of Open Access Journals (Sweden)

Yulius Hero

2011-01-01

Full Text Available Normal 0 false false false EN-US X-NONE X-NONE MicrosoftInternetExplorer4 Furniture is one of wood products to fulfill the household needs, especially for household furnishing. Wood product which is used for furniture tends to decrease because of the substitution products, i.e.: plastic, rattan, bamboo, glass, and metal. To continue their effort, small industries in Indonesia face hard problems and challanges. To solve the hard problems and challenges, then a new marketing strategy through the study on marketing strategy of small wood-furniture industry is needed. This research objectives are to know several factors which have relation toward marketing of woodfurniture and compile alternative small industrial marketing strategy of wood-furniture. Research conducts in Small Industry Centre, Pondok Bambu, East Jakarta from June to July 2008. Some tools are used in this research, such as: questionaire, calculator, camera, and stationery. The method of data collection is purposive sampling with total amount of responden is 30 people-small industry owners. Data analysis uses regression and SWOT method (Strength, Weaknesses. Opportunities, Threath. Result of the research for the regression equation of wood-furniture marketing Y= 9,001 - 0,6798 X1 - 1,4834 X2 - 1,4834 X3 + 0,4818 X4 with value R2 is equal to 51.3%. Linearity test model indicates that F Calculated is 6.57 in significat level α = 1%. Factors that influence wood-furniture marketing of sale volume are variation of product, wood-furniture price, distribution system and promotion. The relation between sale volume with variable of product variation, wood-furniture price, and distribution system is significant with negative direction. It means that smaller product variation, lower wood-furniture price, and more efficient distribution system; will effect to higher sale volume. Whereas the relation between sale volume with variable of promotion is not significant with positive direction. It

Effects of Boron Compounds on the Mechanical and Fire Properties of Wood-chitosan and High-density Polyethylene Composites

Directory of Open Access Journals (Sweden)

Guo-Fu Wu

2014-05-01

Full Text Available Wood-plastic composites (WPCs represent a growing class of durable, low-maintenance construction materials whose use can decrease dependence on petroleum. High-density polyethylene (HDPE, chitosan (CS, wood flour (WF, boric acid (BA, and borax (BX, as well as maleic anhydride grafted polyethylene (MAPE and polyethylene wax (PE wax, were used to develop a durable wood-plastic composite (WPC using the extrusion method. The effects of boron compounds (3%, 6%, 9%, or 12% by weight BA/BX on the mechanical and fire properties of the WPCs were investigated. Mechanical testing indicated that as the percentage weight of boron compounds increased, the flexural modulus, flexural strength, and tensile strength significantly decreased. Cone calorimeter tests were used to characterize the fire performance of the WPCs, and these results suggested that adding BA/BX compounds to WPCs modestly improved the fire performance. As the percentage weight of BA/BX increased from 3% to 9%, the time to ignition (TTI, heat release rate (HRR, total heat release rate (HRR-Total, smoke production rate (SPR, and specific extinction area (SEA of the WPCs were all reduced.

Radioactivity of Wood and Environment

International Nuclear Information System (INIS)

Hus, M.; Kosutic, K.; Lulic, S.

2003-01-01

Nuclear experiments in the atmosphere and nuclear accidents caused global deposition of artificial radionuclides in the soil of Earth's northern hemisphere, the territory of the Republic of Croatia included. Soil contamination by radionuclides resulted in their deposition in plants growing on the contaminated soil as well as in the trees. Large area of the Republic of Croatia is covered with wood, which is exploited in manufacture of industrial wood and for firewood. From approximately 3 million cubic metres of wood exploited annually, nearly one third serves for firewood. In the process of burning a smaller portion of radionuclides deposited in the wood evaporates and goes to atmosphere while a larger portion is retained in the ash. In this paper are presented the results of natural radionuclides 4 0K , 2 32T h and 2 38U as well as of artificial radionuclide 1 37C s content determination in the wood, wood briquette, charcoal and in ash remained after burning the wood, wood briquette and charcoal. The obtained results are discussed from wood radiocontamination aspect and from the aspect of potential environmental radiocontamination by the products from wood burning process. (author)

European wood-fuel trade

International Nuclear Information System (INIS)

Hillring, B.; Vinterbaeck, J.

2001-01-01

This paper discusses research carried out during the l990s on European wood fuel trade at the Department of Forest Management and Products, SLU, in Sweden. Utilisation of wood-fuels and other biofuels increased very rapidly in some regions during that period. Biofuels are replacing fossil fuels which is an effective way to reduce the future influence of green house gases on the climate. The results indicate a rapid increase in wood-fuel trade in Europe from low levels and with a limited number of countries involved. The chief products traded are wood pellets, wood chips and recycled wood. The main trading countries are, for export, Germany and the Baltic states and, for import, Sweden, Denmark and to some extent the Netherlands. In the future, the increased use of biofuel in European countries is expected to intensify activity in this trade. (orig.)

Controversy. The wood war

International Nuclear Information System (INIS)

James, O.

2010-01-01

The author comments the conflict emerging in France between industries exploiting wood for construction and those exploiting it as a heating material for power generation. The first ones accuse the others to steal their raw material, to pull the prices up, and to destabilize the sector. This conflict takes place notably around sawmill wastes which are used either by wood panel fabricators or by wood pellets producers. Both sectors are claiming they are creating more jobs than the other. The French forest indeed offers good opportunities for both sectors, but other countries which are lacking forest surfaces, are buying wood in France. Several issues are matter of discussion: burning wood seems to go against the reduction of greenhouse gas emissions, subsidies awarded to big heater projects. The situation of the wood sector in Austria, Finland and Poland is briefly presented

Studies on thermal degradation and termite resistant properties of chemically modified wood

Energy Technology Data Exchange (ETDEWEB)

Deka, M.; Saikia, C.N. [Council for Scientific and Industrial Research (CSIR), Regional Research Laboratory, Jorhat (India); Baruah, K.K. [Assam Agricultural University, Jorhat (India)

2002-09-01

A series of experiments were carried out to examine the resistant capacity of a chemically treated hard wood, Anthocephalus cadamba (Roxb) Miq. to thermal and termite degradation. The treatment with thermosetting resins viz. urea formaldehyde (UF), melamine formaldehyde (MF) and phenol formaldehyde (PF) at 31-33 levels of weight percent gain (WPG) increased the strength property i.e. modulus of rupture (MOR) by 7.50-21.02% and stiffness i.e. modulus of elasticity (MOE) by 9.50-12.18% over the untreated one with no remarkable effect on specific gravity. The treated samples were found resistant to termite attack, while the untreated one was badly damaged by termites on 12 months' exposure to a termite colony. The thermal degradations of untreated and treated wood samples were studied using thermogravimetric (TGA) and differential thermogravimetric (DTG) techniques at heating rates 20 and 30 {sup o}Cmin{sup -1} in temperature range 30-650{sup o}C. The treated wood was found to be thermally more stable than the untreated one. (author)

Manufacture of wood-pellets doubles. Biowatti Oy started a wood pellet plant in Turenki

International Nuclear Information System (INIS)

Rantanen, M.

1999-01-01

Wood pellets have many advantages compared to other fuels. It is longest processed biofuel with favorable energy content. It is simple to use, transport and store. Heating with wood pellets is cheaper than with light fuel oil, and approximately as cheap as utilization of heavy fuel oil, about 110 FIM/MWh. The taxable price of wood pellets is about 550 FIM/t. Stokers and American iron stoves are equally suitable for combustion of wood pellets. Chip fueled stokers are preferred in Finland, but they are also suitable for the combustion of wood pellets. Wood pellets is an environmentally friendly product, because it does not increase the CO 2 load in the atmosphere, and its sulfur and soot emissions are relatively small. The wood pelletizing plant of Biowatti Oy in Turenki was started in an old sugar mill. The Turenki sugar mill was chosen because the technology of the closed sugar factory was suitable for production of wood pellets nearly as such, and required only by slight modifications. A press, designed for briquetting of sugar beat clippings makes the pellets. The Turenki mill will double the volume of wood pellet manufacture in Finland during the next few years. At the start the annual wood pellet production will be 20 000 tons, but the environmental permit allows the production to be increased to 70 000 tons. At first the mill uses planing machine chips as a raw material in the production. It is the most suitable raw material, because it is already dry (moisture content 8-10%), and all it needs is milling and pelletizing. Another possible raw material is sawdust, which moisture content is higher than with planing machine chips. Most of the wood pellets produced are exported e.g. to Sweden, Denmark and Middle Europe. In Sweden there are over 10 000 single-family houses using wood pellets. Biowatti's largest customer is a power plant located in Stockholm, which combusts annually about 200 000 tons of wood pellets

Reliable and non-destructive positioning of larvae of wood-destroying beetles in wood

International Nuclear Information System (INIS)

Kerner, G.; Thiele, H.; Unger, W.

1980-01-01

Living larvae of wood-destroying insects (house longhorn beetle, deathwatch) can be determined in wood by both X-ray technique and vibration measurements. For such examinations convenient commercial devices were used and tested under laboratory conditions. The methods complement each other and lead to a rationalization of the tests of wood preservatives against wood-destroying insects. It seems to be promising to apply the test methods also to timber already used for building

Lifetime and residual strength of wood subjected to static and variable load

DEFF Research Database (Denmark)

Nielsen, Lauge Fuglsang

1997-01-01

of load amplitude, load average, fractional time under maximum load, and load frequency. The analysis includes prediction of residual strength (re-cycle strength) during the process of load cycling. It is concluded that number of cycles to failure is a very poor design criterion. The theory......).It is demonstrated how the theory developed can be generalised also to consider non-harmonic load variations. An algorithm is presented for this purpose which might be suggested as a qualified alternative to the Palmgren-Miner’s method normally used in fatigue analysis of materials under arbitrary load variations...

Request for wood samples

NARCIS (Netherlands)

NN,

1977-01-01

In recent years the wood collection at the Rijksherbarium was greatly expanded following a renewed interest in wood anatomy as an aid for solving classification problems. Staff members of the Rijksherbarium added to the collection by taking interesting wood samples with them from their expeditions

Effects of wood fiber surface chemistry on strength of wood–plastic composites

Energy Technology Data Exchange (ETDEWEB)

Migneault, Sébastien, E-mail: sebastien.migneault@uqat.ca [University of Quebec in Abitibi-Temiscamingue (UQAT), 445 boulevard de l’Université, Rouyn-Noranda, Québec J9X 5E4 (Canada); Koubaa, Ahmed, E-mail: ahmed.koubaa@uqat.ca [UQAT (Canada); Perré, Patrick, E-mail: patrick.perre@ecp.fr [École centrale de Paris, Grande Voie des Vignes, F-92 295 Chatenay-Malabry Cedex (France); Riedl, Bernard, E-mail: Bernard.Riedl@sbf.ulaval.ca [Université Laval, 2425 rue de la Terrasse, Québec City, Québec G1V 0A6 (Canada)

2015-07-15

Highlights: • Infrared spectroscopy and X-ray photoelectron spectroscopy analyses showed variations of surface chemical characteristics according to fiber origin. • Surface chemical characteristics of fibers could partly explain the differences in mechanical properties of the wood–plastic composites. • Fibers with carbohydrate rich surface led to stronger wood–plastic composites because the coupling between the matrix and fibers using coupling agent is achieved with polar sites mostly available on carbohydrates. • Conversely, lignin or extractives rich surface do not have oxidized functions for the esterification reaction with coupling agent and thus led to wood–plastic composites with lower mechanical properties. • Other factors such as mechanical interlocking and fiber morphology interfere with the effects of fiber surface chemistry. - Abstract: Because wood–plastic composites (WPC) strength relies on fiber-matrix interaction at fiber surface, it is likely that fiber surface chemistry plays an important role in WPC strength development. The objective of the present study is to investigate the relationships between fiber surface chemical characteristics and WPC mechanical properties. Different fibers were selected and characterized for surface chemical characteristics using X-ray photoelectron spectroscopy (XPS) and infrared spectroscopy (FTIR). WPC samples were manufactured at 40% fiber content and with six different fibers. High density polyethylene was used as matrix and maleated polyethylene (MAPE) was used as compatibility agent. WPC samples were tested for mechanical properties and fiber-matrix interface was observed with scanning electron microscope. It was found WPC strength decreases as the amount of unoxidized carbon (assigned to lignin and extractives) measured with XPS on fiber surface increases. In the opposite case, WPC strength increases with increasing level of oxidized carbon (assigned to carbohydrates) on fiber surface. The same

Effects of wood fiber surface chemistry on strength of wood–plastic composites

International Nuclear Information System (INIS)

Migneault, Sébastien; Koubaa, Ahmed; Perré, Patrick; Riedl, Bernard

2015-01-01

Highlights: • Infrared spectroscopy and X-ray photoelectron spectroscopy analyses showed variations of surface chemical characteristics according to fiber origin. • Surface chemical characteristics of fibers could partly explain the differences in mechanical properties of the wood–plastic composites. • Fibers with carbohydrate rich surface led to stronger wood–plastic composites because the coupling between the matrix and fibers using coupling agent is achieved with polar sites mostly available on carbohydrates. • Conversely, lignin or extractives rich surface do not have oxidized functions for the esterification reaction with coupling agent and thus led to wood–plastic composites with lower mechanical properties. • Other factors such as mechanical interlocking and fiber morphology interfere with the effects of fiber surface chemistry. - Abstract: Because wood–plastic composites (WPC) strength relies on fiber-matrix interaction at fiber surface, it is likely that fiber surface chemistry plays an important role in WPC strength development. The objective of the present study is to investigate the relationships between fiber surface chemical characteristics and WPC mechanical properties. Different fibers were selected and characterized for surface chemical characteristics using X-ray photoelectron spectroscopy (XPS) and infrared spectroscopy (FTIR). WPC samples were manufactured at 40% fiber content and with six different fibers. High density polyethylene was used as matrix and maleated polyethylene (MAPE) was used as compatibility agent. WPC samples were tested for mechanical properties and fiber-matrix interface was observed with scanning electron microscope. It was found WPC strength decreases as the amount of unoxidized carbon (assigned to lignin and extractives) measured with XPS on fiber surface increases. In the opposite case, WPC strength increases with increasing level of oxidized carbon (assigned to carbohydrates) on fiber surface. The same

A novel approach in organic waste utilization through biochar addition in wood/polypropylene composites

Energy Technology Data Exchange (ETDEWEB)

Das, Oisik [Department of Civil and Environmental Engineering, University of Auckland, Auckland 1142 (New Zealand); Sarmah, Ajit K., E-mail: a.sarmah@auckland.ac.nz [Department of Civil and Environmental Engineering, University of Auckland, Auckland 1142 (New Zealand); Bhattacharyya, Debes [Department of Mechanical Engineering, Center for Advanced Composite Materials, University of Auckland, Auckland 1142 (New Zealand)

2015-04-15

Highlights: • Biochar made from waste wood was added with wood polypropylene composites. • 24% biochar gave the best mechanical properties. • 6% biochar had no effect on physico-mechanical properties of composites. • Coupling agent remained unreacted in composites having higher amount of biochar. - Abstract: In an attempt to concurrently address the issues related to landfill gas emission and utilization of organic wastes, a relatively novel idea is introduced to develop biocomposites where biochar made from pyrolysis of waste wood (Pinus radiata) is added with the same wood, plastic/polymer (polypropylene) and maleated anhydride polypropylene (MAPP). Experiments were conducted by manufacturing wood and polypropylene composites (WPCs) mixed with 6 wt%, 12 wt%, 18 wt%, 24 wt%, and 30 wt% biochar. Though 6 wt% addition had similar properties to that of the control (composite without biochar), increasing biochar content to 24 wt% improved the composite’s tensile/flexural strengths and moduli. The biochar, having high surface area due to fine particles and being highly carbonised, acted as reinforcing filler in the biocomposite. Composites having 12 wt% and 18 wt% of biochar were found to be the most ductile and thermally stable, respectively. This study demonstrates that, WPCs added with biochar has good potential to mitigate wastes while simultaneously producing biocomposites having properties that might be suited for various end applications.

A novel approach in organic waste utilization through biochar addition in wood/polypropylene composites

International Nuclear Information System (INIS)

Das, Oisik; Sarmah, Ajit K.; Bhattacharyya, Debes

2015-01-01

Highlights: • Biochar made from waste wood was added with wood polypropylene composites. • 24% biochar gave the best mechanical properties. • 6% biochar had no effect on physico-mechanical properties of composites. • Coupling agent remained unreacted in composites having higher amount of biochar. - Abstract: In an attempt to concurrently address the issues related to landfill gas emission and utilization of organic wastes, a relatively novel idea is introduced to develop biocomposites where biochar made from pyrolysis of waste wood (Pinus radiata) is added with the same wood, plastic/polymer (polypropylene) and maleated anhydride polypropylene (MAPP). Experiments were conducted by manufacturing wood and polypropylene composites (WPCs) mixed with 6 wt%, 12 wt%, 18 wt%, 24 wt%, and 30 wt% biochar. Though 6 wt% addition had similar properties to that of the control (composite without biochar), increasing biochar content to 24 wt% improved the composite’s tensile/flexural strengths and moduli. The biochar, having high surface area due to fine particles and being highly carbonised, acted as reinforcing filler in the biocomposite. Composites having 12 wt% and 18 wt% of biochar were found to be the most ductile and thermally stable, respectively. This study demonstrates that, WPCs added with biochar has good potential to mitigate wastes while simultaneously producing biocomposites having properties that might be suited for various end applications

Change of mechanical properties of Norway Spruce wood due to degradation caused by fire retardants

Czech Academy of Sciences Publication Activity Database

Kloiber, Michal; Frankl, Jiří; Drdácký, Miloš; Kučerová, I.; Tippner, J.; Bryscejn, Jan

2010-01-01

Roč. 55, č. 4 (2010), s. 23-38 ISSN 1336-4561 Grant - others:GAČR(CZ) GA103/07/1091 Program:GA Institutional research plan: CEZ:AV0Z20710524 Keywords : wood degradation * fire retardant * mechanical properties * tensile strength * hardness Subject RIV: JN - Civil Engineering Impact factor: 0.284, year: 2010

Wood fuel and the environment

International Nuclear Information System (INIS)

Foster, C.A.

1992-01-01

The purpose of this paper is to try and demonstrate the role that the use of Wood as a Fuel can play in our environment. The term ''Wood Fuel'', for the purposes of these proceedings, refers to the use of wood obtained from the forest or the farm. It does not refer to waste wood from for example buildings. The role of wood fuel in the environment can be assessed at many different levels. In this paper three different scales of ''Environment'' and the role of wood fuel in each, will be considered. These three scales are namely the global environment, the local environment, and the National (community) environment. (Author)

Wood-plastic combination

International Nuclear Information System (INIS)

Schaudy, R.

1978-02-01

A review on wood-plastic combinations is given including the production (wood and plastic component, radiation hardening, curing), the obtained properties, present applications and prospects for the future of these materials. (author)

Production of palm frond based wood plastic composite by using twin screw extruder

Science.gov (United States)

Russita, M.; Bahruddin

2018-04-01

Wood plastic composite (WPC) is the blending product from wood as filler and polymer thermoplastic as matric. Palm frond waste is a material with selulose about 68%, so it has potential to be developed as raw material for WPC. The purpose of this research was to learn how to produce WPC based on palm frond use twin screw extruder. It used popropilen as matric. As for aditif, it used Maleated Polypropilene (MAPP) as compatibilizer and paraffin as plasticizer. The size of palm frond is 40 – 80 mesh. WPC is made from blending polipropylene, palm frond, MAPP and paraffin with dry mixing method in room temperature. Then, PP, Palm frond and additive from dry mixing is fed into twin screw extruder at 190°C and 60 rpm. It use palm frond/polypropylene 60/40, MAPP 5% w/w and paraffin 2% w/w. From the result, it shown that WPC based on palm frond met the standards forcommercial WPC. It has tensile strength up to 19.2 MPa, bending strength 43.6 MPa and water adsorption 0,32% w/w. So, WPC based on palm frond has prospective to be developed for commercial WPC.

Economy of wood supply

International Nuclear Information System (INIS)

Imponen, V.

1993-01-01

Research and development of wood fuels production was vigorous in the beginning of the 1980's. Techniques and working methods used in combined harvesting and transportation of energy and merchantable wood were developed in addition to separate energy wood delivery. After a ten year silent period the research on this field was started again. At present the underutilization of forest supplies and the environmental effects of energy production based on fossil fuels caused the rebeginning of the research. One alternative for reduction of the price of wood fuels at the utilization site is the integration of energy and merchantable wood deliveries together. Hence the harvesting and transportation devices can be operated effectively, and the organizational costs are decreased as well. The wood delivery costs consist of the stumpage price, the harvesting and transportation costs, and of general expenses. The stumpage price form the largest cost category (over 50 %) of the industrial merchantable wood delivery, and the harvesting and transportation costs in the case of thinningwood delivery. Forest transportation is the largest part of the delivery costs of logging residues. The general expenses, consisting of the management costs and the interest costs of the capital bound to the storages, form a remarkable cost category in delivery of low-rank wood for energy or conversion purposes. The costs caused by the harvesting of thinningwood, the logging residues, chipping and crushing, the lorry transportation are reviewed in this presentation

An Analysis of the U.S. Wood Products Import Sector: Prospects for Tropical Wood Products Exporters

Directory of Open Access Journals (Sweden)

W.A.R.T.W. Bandara

2012-10-01

Full Text Available The U.S. has dramatically altered its wood product imports and exports during the past few years,and at present, it is the second largest wood product importer in the world. Hence, an understanding ofmarket structures, factors in selecting foreign suppliers, and the emphasis placed on environmentalissues/certification are critical to understand from the perspective of wood products importers in the U.S.This study provides an analysis of the U.S. wood products import sector with special emphasis on currentand future opportunities for tropical wood products exporters to the U.S. market.In this study, 158 wood products importers in the U.S. were surveyed using a mailingquestionnaire. The adjusted response rate was 40.6 percent. Results indicated that most of the respondentswere small to medium scale firms, but major importers of wood products. According to respondents,wood products to the U.S. mainly come from Brazil, Chile, and China. From the importers’ perspective,Brazilian wood products ranked first for its quality followed by wood products from Chile and Finland.Product quality, long term customer relationships, on-time delivery of orders, fair prices, and supplierreputation were the factors deemed important in selecting overseas suppliers. Majority of respondentswere importing certified wood products. FSC, SFI, and ISO 14000 were the mostly accepted certificationprograms. However, certification was not a major factor in foreign supplier selection criteria. Whenconsidered the U.S. wood products importers’ tendency to diversify their products and species imported,attractive opportunities exist for wood products suppliers from tropical countries.

Wood's lamp examination

Science.gov (United States)

... this page: //medlineplus.gov/ency/article/003386.htm Wood lamp examination To use the sharing features on this page, please enable JavaScript. A Wood lamp examination is a test that uses ultraviolet ( ...

Wood preservation

Science.gov (United States)

Rebecca E. Ibach

1999-01-01

When left untreated in many outdoor applications, wood becomes subject to degradation by a variety of natural causes. Although some trees possess naturally occurring resistance to decay (Ch. 3, Decay Resistance), many are in short supply or are not grown in ready proximity to markets. Because most commonly used wood species, such as Southern Pine, ponderosa pine, and...

The use of new, aqueous chemical wood modifications to improve the durability of wood-plastic composites

Science.gov (United States)

Rebecca E. Ibach; Craig M. Clemons; George C. Chen

2017-01-01

The wood flour used in wood-plastic composites (WPCs) can biologically deteriorate and thus the overall mechanical performance of WPCs decrease when exposed to moisture and fungal decay. Protecting the wood flour by chemical modification can improve the durability of the wood in a nontoxic way so it is not harmful to the environment. WPCs were made with modified wood...

The incorporation of wood waste ash as a partial cement replacement material for making structural grade concrete: An overview

Directory of Open Access Journals (Sweden)

Swaptik Chowdhury

2015-06-01

Full Text Available With increasing industrialization, the industrial byproducts (wastes are being accumulated to a large extent, leading to environmental and economic concerns related to their disposal (land filling. Wood ash is the residue produced from the incineration of wood and its products (chips, saw dust, bark for power generation or other uses. Cement is an energy extensive industrial commodity and leads to the emission of a vast amount of greenhouse gases, forcing researchers to look for an alternative, such as a sustainable building practice. This paper presents an overview of the work and studies done on the incorporation of wood ash as partial replacement of cement in concrete from the year 1991 to 2012. The aspects of wood ash such as its physical, chemical, mineralogical and elemental characteristics as well as the influence of wood ash on properties such as workability, water absorption, compressive strength, flexural rigidity test, split tensile test, bulk density, chloride permeability, freeze thaw and acid resistance of concrete have been discussed in detail.

Moisture Transport in Wood

DEFF Research Database (Denmark)

Astrup, Thomas; Hansen, Kurt Kielsgaard; Hoffmeyer, Preben

2005-01-01

Modelling of moisture transport in wood is of great importance as most mechanical and physical properties of wood depend on moisture content. Moisture transport in porous materials is often described by Ficks second law, but several observations indicate that this does not apply very well to wood....... Recently at the Technical University of Denmark, Department of Civil Engineering, a new model for moisture transport in wood has been developed. The model divides the transport into two phases, namely water vapour in the cell lumens and bound water in the cell walls....

Inside the guts of wood-eating catfishes: can they digest wood?

Science.gov (United States)

German, Donovan P

2009-11-01

To better understand the structure and function of the gastrointestinal (GI) tracts of wood-eating catfishes, the gross morphology, length, and microvilli surface area (MVSA) of the intestines of wild-caught Panaque nocturnus, P. cf. nigrolineatus "Marañon", and Hypostomus pyrineusi were measured, and contrasted against these same metrics of a closely related detritivore, Pterygoplichthys disjunctivus. All four species had anatomically unspecialized intestines with no kinks, valves, or ceca of any kind. The wood-eating catfishes had body size-corrected intestinal lengths that were 35% shorter than the detritivore. The MVSA of all four species decreased distally in the intestine, indicating that nutrient absorption preferentially takes place in the proximal and mid-intestine, consistent with digestive enzyme activity and luminal carbohydrate profiles for these same species. Wild-caught Pt. disjunctivus, and P. nigrolineatus obtained via the aquarium trade, poorly digested wood cellulose (<33% digestibility) in laboratory feeding trials, lost weight when consuming wood, and passed stained wood through their digestive tracts in less than 4 h. Furthermore, no selective retention of small particles was observed in either species in any region of the gut. Collectively, these results corroborate digestive enzyme activity profiles and gastrointestinal fermentation levels in the fishes' GI tracts, suggesting that the wood-eating catfishes are not true xylivores such as beavers and termites, but rather, are detritivores like so many other fishes from the family Loricariidae.

LCA-based optimization of wood utilization under special consideration of a cascading use of wood.

Science.gov (United States)

Höglmeier, Karin; Steubing, Bernhard; Weber-Blaschke, Gabriele; Richter, Klaus

2015-04-01

Cascading, the use of the same unit of a resource in multiple successional applications, is considered as a viable means to improve the efficiency of resource utilization and to decrease environmental impacts. Wood, as a regrowing but nevertheless limited and increasingly in demand resource, can be used in cascades, thereby increasing the potential efficiency per unit of wood. This study aims to assess the influence of cascading wood utilization on optimizing the overall environmental impact of wood utilization. By combining a material flow model of existing wood applications - both for materials provision and energy production - with an algebraic optimization tool, the effects of the use of wood in cascades can be modelled and quantified based on life cycle impact assessment results for all production processes. To identify the most efficient wood allocation, the effects of a potential substitution of non-wood products were taken into account in a part of the model runs. The considered environmental indicators were global warming potential, particulate matter formation, land occupation and an aggregated single score indicator. We found that optimizing either the overall global warming potential or the value of the single score indicator of the system leads to a simultaneous relative decrease of all other considered environmental impacts. The relative differences between the impacts of the model run with and without the possibility of a cascading use of wood were 7% for global warming potential and the single score indicator, despite cascading only influencing a small part of the overall system, namely wood panel production. Cascading led to savings of up to 14% of the annual primary wood supply of the study area. We conclude that cascading can improve the overall performance of a wood utilization system. Copyright © 2015 Elsevier Ltd. All rights reserved.

Creation of Wood Dust during Wood Processing: Size Analysis, Dust Separation, and Occupational Health

Directory of Open Access Journals (Sweden)

Eva Mračková

2015-11-01

Full Text Available Mechanical separators and fabric filters are being used to remove airborne fine particles generated during the processing and handling of wood. Such particles might have a harmful effect on employee health, not only in small- but also in large-scale wood processing facilities. The amount of wood dust and its dispersion conditions vary according to geometric boundary conditions. Thus, the dispersion conditions could be changed by changing the linear size of the particles. Moreover, the smaller the particles are, the more harmful they can be. It is necessary to become familiar with properties, from a health point of view, of wood dust generated from processing. Wood dust has to be sucked away from the processing area. The fractional separation efficiency of wood dust can be improved using exhaust and filtering devices. Filtration efficiency depends on moisture content, particle size, and device performance. Because of the carcinogenicity of wood dust, the concentration of wood dust in air has to be monitored regularly. Based on the results hereof, a conclusion can be made that both mechanical separators of types SEA and SEB as well as the fabric filters with FINET PES 1 textile are suitable for the separation of wet saw dust from all types of wooden waste produced within the process.

Reactivity and burnout of wood fuels

DEFF Research Database (Denmark)

Dall'Ora, Michelangelo

This thesis deals with the combustion of wood in pulverised fuel power plants. In this type of boiler, the slowest step in the wood conversion process is char combustion, which is one of the factors that not only determine the degree of fuel burnout, but also affect the heat release profile...... of different aspects relevant to wood combustion, including wood structure and composition, wood pyrolysis, wood char properties and wood char oxidation. The full scale campaign, which is the subject of Chapter 3, included sampling of wood fuel before and after milling and sampling of gas and particles...... at the top of the combustion chamber. The collected samples and data are used to obtain an evaluation of the mills in operation at the power plant, the particle size distribution of the wood fuel, as well as the char conversion attained in the furnace. In Chapter 4 an experimental investigation...

Reinforcement of Bolted Timber Joints Using GFRP Sheets in Poplar and Pine Woods

Directory of Open Access Journals (Sweden)

Mehrab Madhoushi

2013-01-01

Full Text Available Failure in timber structures occurs mainly in crucial points such as joints areas. Therefore, the idea of using composite sheets in timber joints has been intro-duced as a method in order to increase the strength and ductility behaviour of timber joints. This research aims to study the behaviour of bolted joints in poplar and pine woods, which are reinforced by two types of GFRP sheets. A single shear bolted joint consisted of 3 timber members whose length and width were 30 cm in length and 5 cm in width. The thickness of each member was 4 cm for internal part and 2 cm for external part. The employed steel bolt was 10 cm in length and 1 cm in diameter. In this respect, one layer of GFRP sheet was used to be bonded to timber members by using epoxy resin and left between the clamps for 24 hours. They were then kept at room temperature for three weeks. Also the effect of adding a wood veneer on the reinforced joints was investigated. The tensile strength of the reinforced and control samples (un-reinforced joints was measured according to ASTM D5652-92 standard. The results show that the reinforced samples have higher tensile strength compared to that of reinforced joints, although it is not statistically signifcant. Also, two types of sheets infuence the joint behaviour as the reinforced joints display more ductility behaviour.

Application of molecular genetic methods for identification of wood-decaying fungi in wood constructions

OpenAIRE

Elena Bobeková; Michal Tomšovský; Petr Horáček

2008-01-01

The aim of the paper is to evaluate the utilization of molecular biology methods for detection of wood decaying fungi directly from decomposed wood using a commercial DNA extraction kit developed for soil substrates (PowerSoil™ DNA isolation kit). The experiment based on dry rot fungus (Serpula lacrymans) detection from inoculated wooden pieces under laboratory conditions was followed by field detection of wood-decaying fungi from wood structures on building constructions. Fungal DNA was ide...

Fabrication of Wood-Rubber Composites Using Rubber Compound as a Bonding Agent Instead of Adhesives

Directory of Open Access Journals (Sweden)

Dongwei Shao

2016-06-01

Full Text Available Differing from the hot-pressing method in the manufacturing of traditional wood-rubber composites (WRCs, this study was aimed at fabricating WRCs using rubber processing to improve water resistance and mechanical properties. Three steps were used to make WRCs, namely, fiber-rubber mixing, tabletting, and the vulcanization molding process. Ninety-six WRC panels were made with wood fiber contents of 0%–50% at rotor rotational speeds of 15–45 rpm and filled coefficients of 0.55–0.75. Four regression equations, i.e., the tensile strength (Ts, elongation at break (Eb, hardness (Ha and rebound resilience (Rr as functions of fiber contents, rotational speed and filled coefficient, were derived and a nonlinear programming model were developed to obtain the optimum composite properties. Although the Ts, Eb and Rr of the panels were reduced, Ha was considerably increased by 17%–58% because of the wood fiber addition. Scanning electron microscope images indicated that fibers were well embedded in rubber matrix. The 24 h water absorption was only 1%–3%, which was much lower than commercial wood-based composites.

Fabrication of Wood-Rubber Composites Using Rubber Compound as a Bonding Agent Instead of Adhesives.

Science.gov (United States)

Shao, Dongwei; Xu, Min; Cai, Liping; Shi, Sheldon Q

2016-06-14

Differing from the hot-pressing method in the manufacturing of traditional wood-rubber composites (WRCs), this study was aimed at fabricating WRCs using rubber processing to improve water resistance and mechanical properties. Three steps were used to make WRCs, namely, fiber-rubber mixing, tabletting, and the vulcanization molding process. Ninety-six WRC panels were made with wood fiber contents of 0%-50% at rotor rotational speeds of 15-45 rpm and filled coefficients of 0.55-0.75. Four regression equations, i.e. , the tensile strength ( T s), elongation at break ( E b), hardness ( H a) and rebound resilience ( R r) as functions of fiber contents, rotational speed and filled coefficient, were derived and a nonlinear programming model were developed to obtain the optimum composite properties. Although the T s, E b and R r of the panels were reduced, H a was considerably increased by 17%-58% because of the wood fiber addition. Scanning electron microscope images indicated that fibers were well embedded in rubber matrix. The 24 h water absorption was only 1%-3%, which was much lower than commercial wood-based composites.

Adhesive interactions with wood

Science.gov (United States)

Charles R. Frihart

2004-01-01

While the chemistry for the polymerization of wood adhesives has been studied systematically and extensively, the critical aspects of the interaction of adhesives with wood are less clearly understood. General theories of bond formation need to be modified to take into account the porosity of wood and the ability of chemicals to be absorbed into the cell wall....

Composite structure of wood cells in petrified wood

International Nuclear Information System (INIS)

Nowak, Jakub; Florek, Marek; Kwiatek, Wojciech; Lekki, Janusz; Chevallier, Pierre; Zieba, Emil; Mestres, Narcis; Dutkiewicz, E.M.; Kuczumow, Andrzej

2005-01-01

Special kinds of petrified wood of complex structure were investigated. All the samples were composed of at least two different inorganic substances. The original cell structure was preserved in each case. The remnants of the original biological material were detected in some locations, especially in the cell walls. The complex inorganic structure was superimposed on the remnant organic network. The first inorganic component was located in the lumena (l.) of the cells while another one in the walls (w.) of the cells. The investigated arrangements were as follows: calcite (l.)-goethite-hematite (w.)-wood from Dunarobba, Italy; pyrite (l.)-calcite (w.)-wood from Lukow, Poland; goethite (l.)-silica (w.)-wood from Kwaczala, Poland. The inorganic composition was analysed and spatially located by the use of three spectral methods: electron microprobe, X-ray synchrotron-based microprobe, μ-PIXE microprobe. The accurate mappings presenting 2D distribution of the chemical species were presented for each case. Trace elements were detected and correlated with the distribution of the main elements. In addition, the identification of phases was done by the use of μ-Raman and μ-XRD techniques for selected and representative points. The possible mechanisms of the described arrangements are considered. The potential synthesis of similar structures and their possible applications are suggested

Composite structure of wood cells in petrified wood

Energy Technology Data Exchange (ETDEWEB)

Nowak, Jakub [Department of Chemistry, Catholic University of Lublin, 20-718 Lublin (Poland); Florek, Marek [Department of Chemistry, Catholic University of Lublin, 20-718 Lublin (Poland); Kwiatek, Wojciech [Institute of Nuclear Physics, Department of Nuclear Spectroscopy, 31-342 Cracow (Poland); Lekki, Janusz [Institute of Nuclear Physics, Department of Nuclear Spectroscopy, 31-342 Cracow (Poland); Chevallier, Pierre [LPS, CEN Saclay et LURE, Universite Paris-Sud, Bat 209D, F-91405 Orsay (France); Zieba, Emil [Department of Chemistry, Catholic University of Lublin, 20-718 Lublin (Poland); Mestres, Narcis [Institut de Ciencia de Materials de Barcelona (ICMAB), Campus de la UAB, E-08193-Bellaterra (Spain); Dutkiewicz, E.M. [Institute of Nuclear Physics, Department of Nuclear Spectroscopy, 31-342 Cracow (Poland); Kuczumow, Andrzej [Department of Chemistry, Catholic University of Lublin, 20-718 Lublin (Poland)

2005-04-28

Special kinds of petrified wood of complex structure were investigated. All the samples were composed of at least two different inorganic substances. The original cell structure was preserved in each case. The remnants of the original biological material were detected in some locations, especially in the cell walls. The complex inorganic structure was superimposed on the remnant organic network. The first inorganic component was located in the lumena (l.) of the cells while another one in the walls (w.) of the cells. The investigated arrangements were as follows: calcite (l.)-goethite-hematite (w.)-wood from Dunarobba, Italy; pyrite (l.)-calcite (w.)-wood from Lukow, Poland; goethite (l.)-silica (w.)-wood from Kwaczala, Poland. The inorganic composition was analysed and spatially located by the use of three spectral methods: electron microprobe, X-ray synchrotron-based microprobe, {mu}-PIXE microprobe. The accurate mappings presenting 2D distribution of the chemical species were presented for each case. Trace elements were detected and correlated with the distribution of the main elements. In addition, the identification of phases was done by the use of {mu}-Raman and {mu}-XRD techniques for selected and representative points. The possible mechanisms of the described arrangements are considered. The potential synthesis of similar structures and their possible applications are suggested.

Sustainable wood waste management in Nigeria

Directory of Open Access Journals (Sweden)

Owoyemi Jacob Mayowa

2016-09-01

Full Text Available Wood industries produce large volumes of residues which must be utilized, marketed or properly disposed of. Heaps of wood residues are common features in wood industries throughout the year. In Nigeria, this residue is generally regarded as waste and this has led to open burning practices, dumping in water bodies or dumping in an open area which constitutes environmental pollution. Sawmills in Nigeria generated over 1,000,000 m3 of wood waste in 2010 while about 5000 m3 of waste was generated in plywood mills. Nigeria generates about 1.8 million tons of sawdust annually and 5.2 million tons of wood wastes. The impact of improper disposal of waste wood on the environment affects both the aquatic and terrestrial ecosystems. Also burning of waste wood releases greenhouse gases into the atmosphere causing various health issues. Reuse/recycling of these wood residues in Nigeria will reduce the pressure on our ever decreasing forests, reduce environmental pollution, create wealth and employment. The literature available on this subject was reviewed and this article, therefore, focuses on the various methods of wood waste disposal and its utilization in Nigerian wood industries, the effects of wood waste on the environment as well as on human health and the benefits of proper wood waste management practices.

Structure and function of wood

Science.gov (United States)

Alex Wiedenhoeft

2010-01-01

Wood is a complex biological structure, a composite of many chemistries and cell types acting together to serve the needs of a living plant. Attempting to understand wood in the context of wood technology, we have often overlooked the key and basic fact that wood evolved over the course of millions of years to serve three main functions in plants― conduction of water...

Wood pellets : a worldwide fuel commodity

International Nuclear Information System (INIS)

Melin, S.

2005-01-01

Aspects of the wood pellet industry were discussed in this PowerPoint presentation. Details of wood pellets specifications were presented, and the wood pellet manufacturing process was outlined. An overview of research and development activities for wood pellets was presented, and issues concerning quality control were discussed. A chart of the effective calorific value of various fuels was provided. Data for wood pellet mill production in Canada, the United States and the European Union were provided, and various markets for Canadian wood pellets were evaluated. Residential sales as well as Canadian overseas exports were reviewed. Production revenues for British Columbia and Alberta were provided. Wood pellet heat and electricity production were discussed with reference to prefabricated boilers, stoves and fireplaces. Consumption rates, greenhouse gas (GHG) emissions, and fuel ratios for wood pellets and fossil fuels were compared. Price regulating policies for electricity and fossil fuels have prevented the domestic expansion of the wood pellet industry. There are currently no incentives for advanced biomass combustion to enter British Columbia markets, and this has led to the export of wood pellets. It was concluded that climate change mitigation policies will be a driving force behind market expansion for wood pellets. tabs., figs

Acoustic and adsorption properties of submerged wood

Science.gov (United States)

Hilde, Calvin Patrick

Wood is a common material for the manufacture of many products. Submerged wood, in particular, is used in niche markets, such as the creation of musical instruments. An initial study performed on submerged wood from Ootsa Lake, British Columbia, provided results that showed that the wood was not suitable for musical instruments. This thesis re-examined the submerged wood samples. After allowing the wood to age unabated in a laboratory setting, the wood was retested under the hypothesis that the physical acoustic characteristics would improve. It was shown, however, that the acoustic properties became less adequate after being left to sit. The adsorption properties of the submerged wood were examined to show that the submerged wood had a larger accessible area of wood than that of control wood samples. This implied a lower amount of crystalline area within the submerged wood. From the combined adsorption and acoustic data for the submerged wood, relationships between the moisture content and speed of sound were created and combined with previous research to create a proposed model to describe how the speed of sound varies with temperature, moisture content and the moisture content corresponding to complete hydration of sorption sites within the wood.

Urban Wood Waste Resource Assessment; TOPICAL

International Nuclear Information System (INIS)

Wiltsee, G.

1998-01-01

This study collected and analyzed data on urban wood waste resources in 30 randomly selected metropolitan areas in the United States. Three major categories wood wastes disposed with, or recovered from, the municipal solid waste stream; industrial wood wastes such as wood scraps and sawdust from pallet recycling, woodworking shops, and lumberyards; and wood in construction/demolition and land clearing debris

Moisture Performance of wood-plastic composites reinforced with extracted and delignified wood flour

Science.gov (United States)

Yao Chen; Nicole M. Stark; Mandla A. Tshabalala; Jianmin Gao; Yongming Fan

2014-01-01

This study investigated the effect of using extracted and delignified wood flour on water sorption properties of wood–plastic composites. Wood flour (WF) extraction was performed with three solvent systems: toluene/ethanol (TE), acetone/water (AW), and hot water (HW); delignification was conducted using sodium chlorite/acetic acid solution. A 24 full-factorial...

Survival, growth, wood basic density and wood biomass of seven ...

African Journals Online (AJOL)

A performance comparison of seven-year-old individuals of 13 Casuarina species/provenances in terms of survival, growth (diameter, height and volume), wood basic density and wood biomass was undertaken at Kongowe, Kibaha, Tanzania. The trial was laid out using a randomised complete block design with four ...

Chapter 9: Wood Energy

Science.gov (United States)

Francisco X. Aguilar; Karen Abt; Branko Glavonjic; Eugene Lopatin; Warren  Mabee

2016-01-01

The availabilty of information on wood energy continues to improve, particularly for commoditized woodfuels.  Wood energy consumption and production vary in the UNECE region because demand is strngly affected by weather and the prices of competing energy sources.  There has been an increase in wood energy in the power-and-heat sector in the EU28 and North American...

Iron Stain on Wood

Science.gov (United States)

Mark Knaebe

2013-01-01

Iron stain, an unsightly blue–black or gray discoloration, can occur on nearly all woods. Oak, redwood, cypress, and cedar are particularly prone to iron stain because these woods contain large amounts of tannin-like extractives. The discoloration is caused by a chemical reaction between extractives in the wood and iron in steel products, such as nails, screws, and...

On-line automatic detection of wood pellets in pneumatically conveyed wood dust flow

Science.gov (United States)

Sun, Duo; Yan, Yong; Carter, Robert M.; Gao, Lingjun; Qian, Xiangchen; Lu, Gang

2014-04-01

This paper presents a piezoelectric transducer based system for on-line automatic detection of wood pellets in wood dust flow in pneumatic conveying pipelines. The piezoelectric transducer senses non-intrusively the collisions between wood pellets and the pipe wall. Wavelet-based denoising is adopted to eliminate environmental noise and recover the collision events. Then the wood pellets are identified by sliding a time window through the denoised signal with a suitable threshold. Experiments were carried out on a laboratory test rig and on an industrial pneumatic conveying pipeline to assess the effectiveness and operability of the system.

EXPERIMENTAL RESEARCH CONCERNING THE OPTIMAL DIMENSIONS OF AN ELASTIC STRUCTURE OF BEECH WOOD PARQUET

Directory of Open Access Journals (Sweden)

Olimpia-Minerva ȚURCAȘ (DIACONU

2015-12-01

Full Text Available This paper presents the results of the experimental research concerning the modulus of elasticity and the average value of the bending strength in case of beech (Fagus sylvatica L. wood. The investigations were performed according to SR EN 408-2004. The results of the research have been analysed in order to establish the variable parameters to be considered for the final experimental research focused on beech wood floor structures that meet the necessary requirements for the sports halls applications. The research presented in the paper is a part of the study theme of the Ph. D. thesis, which investigates the flooring structures able to support the requirements of sports halls activities, different from one sport to another.

State-of-the-art of the European regulation on wood wastes and wood ashes valorization. Synthesis

International Nuclear Information System (INIS)

Mousseau, S.

2007-01-01

This study has the objective of comparing the regulations of 10 European countries with that of France, in relation to the classification and recycling of wood waste, in particular lightly treated wood, as well as recycling of wood ash. The first part relating to wood waste presents a detailed analysis by country as well as a summary, on the one hand, of the various sectors for recycling waste wood and, on the other, the emission limits for their energy recovery. Generally, there is a distinction between waste covered by the incineration directive, and the others, without any particular category for lightly treated wood. However, recommendations emerge from this that are based essentially on the regulations or guidelines observed in Germany, Austria and the United Kingdom. The second part relating to wood ash also a presents a detailed analysis by country as well as a summary of the various sectors of recycling and limit values for spreading. Ash is generally considered as waste, and is recycled on a case-by case basis. Only Germany and Austria have clearly integrated wood ash in their regulatory framework. Overall this study shows the need for uniform regulation at European level, establishing environment requirements for recycling wood waste and wood ash, in order to encourage development of the use of biomass

Wood Flour Moulding Technology: Implications for Technical ...

African Journals Online (AJOL)

The intent of this article is to demonstrate how wood waste called sawdust or wood flour can be transformed by plastic moulding machine into items of economic value. Wood flour is wood reduced to very fine particle form. It can be waste product from saw mills, wood working plants or produced from selected dry wood by ...

Wood wastes: Uses

International Nuclear Information System (INIS)

Cipro, A.

1993-01-01

The 1,500 industrial firms manufacturing furniture in the Italian Province of Treviso can generate up to 190,000 tonnes of wood wastes annually. In line with the energy conservation-environmental protection measures contained in Italian Law No. 475/88, this paper indicates convenient uses for these wood wastes - as a raw material for fibreboards or as a fuel to be used in the furniture manufacturing plants themselves and in kilns producing lime. Reference is made to the wood wastes gasification/power generation system being developed by ENEA (the Italian Agency for New Technology, Energy and the Environment)

Fire Safety Design of Wood Structures

DEFF Research Database (Denmark)

Hertz, Kristian Dahl

2006-01-01

Lecture Notes on Fire Safety Design of Wood Structures including charring of wood and load bearing capacity of beams, columns, and connections.......Lecture Notes on Fire Safety Design of Wood Structures including charring of wood and load bearing capacity of beams, columns, and connections....

WOOD BIOMASS FOR ENERGY IN MONTENEGRO

Directory of Open Access Journals (Sweden)

Gradimir Danon

2010-01-01

Full Text Available Wood biomass has got its place in the energy balance of Montenegro. A little more than 6% of the total energy consumption is obtained by burning wood. Along with the appropriate state measures, it is economically and environmentally justified to expect Montenegro to more than double the utilization of the existing renewable energy sources including wood biomass, in the near future. For the purpose of achieving this goal, ‘Commercial Utilisation of the Wood Residue as a Resource for Economic Development in the North of Montenegro' project was carried out in 2007. The results of this project were included in the plan of the necessary interventions of the Government and its Agencies, associations or clusters, non-government organisations and interested enterprises. The plan was made on the basis of the wood residue at disposal and the attitude of individual subjects to produce and/or use solid bio-fuels and consists of a proposal of collection and utilisation of the wood residue for each individual district in the north of Montenegro. The basic factors of sustainability of future commercialisation of the wood residue were: availability of the wood raw material, and thereby the wood residue; the development of wood-based fuel markets, and the size of the profit.

Plasma enhanced modification of TMP fiber and its effect on tensile strength of wood fiber/PP composite

Science.gov (United States)

Sangyeob Lee; Todd F. Shupe; Chung Y. Hse

2009-01-01

Plasma-assisted surface treatment on thermomechanical pulp (TMP) fiber and polypropylene (PP) film was investigated to obtain interfacial adhesion at the wood fiber and PP interface. A metal plate between electrodes prevented thermal damage to the TMP fiber handsheets and PP film. Oxygen-plasma treatment provided better surface activation on the TMP fiber and...

Corrosion of Fasteners in Wood Treated with Newer Wood Preservatives

Science.gov (United States)

Samuel L. Zelinka

2013-01-01

This document compiles recent research findings related to corrosion of metals in preservative treated wood into a single report on corrosion of metals in wood. The research was conducted as part of the Research, Technology and Education portion of the National Historic Covered Bridge Preservation (NHCBP) Program administered by the Federal Highway Administration. The...

Power generation from waste wood

Energy Technology Data Exchange (ETDEWEB)

Nitsche, H

1980-04-18

Since the energy crisis, power generation from waste wood has become increasingly important. The most profitable way to use waste wood in woodworking plants with an annual production of 100 to 150,000 m/sup 3/ solid measure of wood chips and bark is by combustion and thermal energy recovery. In plants with an annual production of 10,000 m/sup 3/ solid measure of wood chips and bark, electric power generation is a suitable application.

Possibilities for the Use of Wood Ashes in Agriculture

Directory of Open Access Journals (Sweden)

Barbara Symanowicz

2018-05-01

The following physical properties of the ashes were determined: colour, solubility, porosity, absorbability, compression strength, degree of fineness, moisture content and spreadability. In the ashes obtained from the combustion of wood in a fireplace furnace, the following parameters were determined: pH H2O, pHKCl (1 mole dm-3 KCl, pHCaCl2 (0.01 mole dm-3 CaCl2 and total alkalinity in terms of the suitability of ashes as a liming agent. The contents of Ctot. and Ntot. were determined with a CHNS/O elemental analyser by Perkin-Elmer and the contents of other elements (macronutrients and heavy metals were specified using the method of atomic emission spectrometry with inductively coupled plasma ICP-AES. Wood ashes are a source of macronutrients for plants. Their contents can be presented in the following series of decreasing values: Ca > C > K > Mg > P > S > N. Out of 1 t of wood ash, approx. 160 kg C, 6 kg N, 20 kg P, 98 kg K, 302 kg Ca, 39 kg Mg and 18 kg S can be introduced into the soil. The content of heavy metals in the analysed ashes was low, and exceeded the acceptable standards for their content in waste materials intended for liming soils. The analysed ashes exhibit good physical and chemical properties. They can be suitable for use in agriculture as a liming agent to be applied on medium and heavy soils.

Mechanical behavior of wood subjected to mode II fracture, using an energetic criterion: Application on THUJA of Morocco

Directory of Open Access Journals (Sweden)

Amal Saoud

2018-04-01

Full Text Available Shear strength is one of the properties often used to qualify a wood species for use in industry. But until now there is no standardized test which allows understanding this phenomenon. This paper constitutes a new approach to study the behavior of the wood material subjected to the mode II fracture. For that we designed and realized a new prototype of a wooden specimen that we tested in our laboratory which gives rise to an evaluation of the fracture until separation by pure shear of the specimen in the TL plane. The experimental data from a first series of tests on Thuja wood (Tetraclinis Articulata (Vahl Masters as a test material as well as the calculation of mode II initiation fracture toughness and the critical stress intensity factor are presented in this paper

Source strengths for indoor human activities that resuspend particulate matter.

Science.gov (United States)

Ferro, Andrea R; Kopperud, Royal J; Hildemann, Lynn M

2004-03-15

A mathematical model was applied to continuous indoor and outdoor particulate matter (PM) measurements to estimate source strengths for a variety of prescribed human activities that resuspend house dust in the home. Activities included folding blankets, folding clothes, dry dusting, making a bed, dancing on a rug, dancing on a wood floor, vacuuming, and walking around and sitting on upholstered furniture. Although most of the resuspended particle mass from these activities was larger than 5 microm in diameter, the resuspension of PM2.5 and PM5 was substantial, with source strengths ranging from 0.03 to 0.5 mg min(-1) for PM2.5 and from 0.1 to 1.4 mg min(-1) for PM5. Source strengths for PM > 5 microm could not be quantified due to instrument limitations. The source strengths were found to be a function of the number of persons performing the activity, the vigor of the activity, the type of activity, and the type of flooring.

Status of wood energy applications

International Nuclear Information System (INIS)

Zerbe, J.I.

1991-01-01

In this address, the potential of wood and wood residues to supply future energy needs is examined. In addition, the possible environmental impact of the use of wood fuels on global climate change is discussed. Technologies for the development of new fuels are described

Choosing Wood Burning Appliances

Science.gov (United States)

Information to assist consumers in choosing a wood burning appliance, including types of appliances, the differences between certified and non-certified appliances, and alternative wood heating options.

EFFECT OF FERTILIZATION ON MECHANICAL PROPERTIES OF THE WOOD OF Eucalyptus grandis

Directory of Open Access Journals (Sweden)

Israel Luiz de Lima

2011-09-01

Full Text Available The effect of the fertilization in the amount and quality of the produced wood is one of the questions to be considered in the research of the Eucalyptus grandis. The present work aimed to evaluate the fertilization effect in the mechanical properties of Eucalyptus grandis. The population of Eucalyptus grandis was 21 years old and was managed under the system of selective thinning, with application of fertilizers. The factors used in this study were: presence or absence of fertilizers, two positions of log and five radial positions. The influences of the factors and of their combinations were evaluated regarding to compression strength, shear strength, modulus of rupture and modulus of elasticity in static banding. The compressive strength and the modulus of elasticity had been influenced by the factors: fertilizer and radial positions of the log. There was also an increase in the direction of the pith-bark in all studied properties. A good positive relationship was found to exist among the compression strength, the shear, the modulus of rupture and the modulus of elasticity with radial position.

Bacterial Community Succession in Pine-Wood Decomposition.

Science.gov (United States)

Kielak, Anna M; Scheublin, Tanja R; Mendes, Lucas W; van Veen, Johannes A; Kuramae, Eiko E

2016-01-01

Though bacteria and fungi are common inhabitants of decaying wood, little is known about the relationship between bacterial and fungal community dynamics during natural wood decay. Based on previous studies involving inoculated wood blocks, strong fungal selection on bacteria abundance and community composition was expected to occur during natural wood decay. Here, we focused on bacterial and fungal community compositions in pine wood samples collected from dead trees in different stages of decomposition. We showed that bacterial communities undergo less drastic changes than fungal communities during wood decay. Furthermore, we found that bacterial community assembly was a stochastic process at initial stage of wood decay and became more deterministic in later stages, likely due to environmental factors. Moreover, composition of bacterial communities did not respond to the changes in the major fungal species present in the wood but rather to the stage of decay reflected by the wood density. We concluded that the shifts in the bacterial communities were a result of the changes in wood properties during decomposition and largely independent of the composition of the wood-decaying fungal communities.

Synthesis and characterization of starch-g-poly(vinyl acetate-co-butyl acrylate) bio-based adhesive for wood application.

Science.gov (United States)

Zia-Ud-Din; Chen, Lei; Ullah, Ikram; Wang, Peng Kai; Javaid, Allah Bakhsh; Hu, Chun; Zhang, Mengchao; Ahamd, Ishtiaq; Xiong, Hanguo; Wang, Zhenjiong

2018-07-15

Enhancing the performance of wood adhesive is important for its industrial applications. Accordingly, we designed and demonstrated the use of two co-monomers vinyl acetate (VAc) and butyl acrylate (BA) for promoting the graft copolymerization while improving the bonding performance of wood adhesive. The results showed that the addition of co-monomers in the ratio of VAc/BA 6:4 (v/v, volume basis of VAc) could improve the shear strength to 6.68MPa and 3.32MPa in dry and wet states, respectively. 1 H-nuclear magnetic resonance ( 1 H NMR) and fourier transform infrared spectroscopy (FT-IR) analysis revealed successful graft copolymerization reaction while the morphologies were observed by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). Furthermore, the grafting reaction and thermal stabilities of wood adhesive were analyzed by X-ray photoelectron spectroscopy (XPS) and thermogravimetric analysis (TGA). The results showed that the properties of wood adhesive could improve dramatically by using two co-monomers VAc and BA during the graft copolymerization reaction. Copyright © 2018 Elsevier B.V. All rights reserved.

Wood power in North Carolina

Energy Technology Data Exchange (ETDEWEB)

Cleland, J.G.; Guessous, L. [Research Triangle Institute, Research Triangle Park, NC (United States)

1993-12-31

North Carolina (NC) is one of the most forested states, and supports a major wood products industry. The NC Department of Natural Resources sponsored a study by Research Triangle Institute to examine new, productive uses of the State`s wood resources, especially electric power generation by co-firing with coal. This paper summarizes our research of the main factors influencing wood power generation opportunities, i.e., (1) electricity demand; (2) initiative and experience of developers; (3) available fuel resources; (4) incentives for alternate fuels; and (5) power plant technology and economics. The results cover NC forests, short rotation woody crops, existing wood energy facilities, electrical power requirements, and environmental regulations/incentives. Quantitative assessments are based on the interests of government agencies, utilities, electric cooperatives, developers and independent power producers, forest products industries, and the general public. Several specific, new opportunities for wood-to-electricity in the State are identified and described. Comparisons are made with nationwide resources and wood energy operations. Preferred approaches in NC are co-generation in existing or modified boilers and in dedicated wood power plants in forest industry regions. Co-firing is mainly an option for supplementing unreliable primary fuel supplies to existing boilers.

The Carbon Impacts of Wood Products

Science.gov (United States)

Richard Bergman; Maureen Puettmann; Adam Taylor; Kenneth E. Skog

2014-01-01

Wood products have many environmental advantages over nonwood alternatives. Documenting and publicizing these merits helps the future competitiveness of wood when climate change impacts are being considered. The manufacture of wood products requires less fossil fuel than nonwood alternative building materials such as concrete, metals, or plastics. By nature, wood is...

The influence of irradiated wood filler on some properties of polypropylene - wood composites

Directory of Open Access Journals (Sweden)

Điporović-Momčilović Milanka

2007-01-01

Full Text Available The problem of compatibility between the wood filler and thermoplastic matrix is of essential importance in composite production. Numerous methods have been developed for increasing this compatibility, which is still representing a challenging objective of composite research throughout the world. The research into these methods is primarily directed towards their efficiency from the viewpoint of the composite performance and their economical acceptability. The latter is of particular importance for the composite production in the developing countries with respect to the shortage of the corresponding funds. With this respect, the utilization of ionizing radiation might have considerable advantages. In this research, the beech wood flour was irradiated by a dose of 10 kGy of 60Co gamma rays for purpose of provoking the changes by the ionizing effect. The effects of ionizing radiation upon the properties of wood particles have been examined by IR spectroscopy and by determination of contents of hydroxyl groups in wood by acetylating as an indirect method. All these methods have been expected to reveal the chemical effects of the applied radiation treatment. The irradiated and the control wood flour were used in order to produce the samples of composite with polypropylene. The polypropylene-wood flour (PP-WF composites were produced with 40% of wood particles having fraction size 0.3 mm. The melt-blended composites were modified with amido-acrylic acid (AMACA as a new coupling agent synthesized for this propose in amount of 6 wt.% (based on wood filler and successively with 0.05 wt.% (based on PP of organic peroxide during mixing step. The composites containing coupling agents showed superior mechanical properties, compared to the untreated one. The highest extent of improvement of tensile was achieved in PP-WFl composites modified with AMACA coupling agent.

Methane from wood

Energy Technology Data Exchange (ETDEWEB)

Schulz, T. F.; Barreto, L.; Kypreos, S.; Stucki, S

2005-07-15

The role of wood-based energy technologies in the Swiss energy system in the long-term is examined using the energy-system Swiss MARKAL model. The Swiss MARKAL model is a 'bottom-up' energy-systems optimization model that allows a detailed representation of energy technologies. The model has been developed as a joint effort between the Energy Economics Group (EEG) at Paul Scherrer Institute PSI) and the University of Geneva and is currently used at PSI-EEG. Using the Swiss MARKAL model, this study examines the conditions under which wood-based energy technologies could play a role in the Swiss energy system, the most attractive pathways for their use and the policy measures that could support them. Given the involvement of PSI in the ECOGAS project, especial emphasis is put on the production of bio-SNG from wood via gasification and methanation of syngas and on hydrothermal gasification of woody biomass. Of specific interest as weIl is the fraction of fuel used in passenger cars that could be produced by locally harvested wood. The report is organized as follows: Section 2 presents a brief description of the MARKAL model. Section 3 describes the results of the base case scenario, which represents a plausible, 'middle-of-the-road' development of the Swiss energy system. Section 4 discusses results illustrating the conditions under which the wood-based methanation technology could become competitive in the Swiss energy market, the role of oil and gas prices, subsidies to methanation technologies and the introduction of a competing technology, namely the wood-based Fischer-Tropsch synthesis. FinaIly, section 5 outlines some conclusions from this analysis. (author)

Methane from wood

International Nuclear Information System (INIS)

Schulz, T. F.; Barreto, L.; Kypreos, S.; Stucki, S.

2005-07-01

The role of wood-based energy technologies in the Swiss energy system in the long-term is examined using the energy-system Swiss MARKAL model. The Swiss MARKAL model is a 'bottom-up' energy-systems optimization model that allows a detailed representation of energy technologies. The model has been developed as a joint effort between the Energy Economics Group (EEG) at Paul Scherrer Institute PSI) and the University of Geneva and is currently used at PSI-EEG. Using the Swiss MARKAL model, this study examines the conditions under which wood-based energy technologies could play a role in the Swiss energy system, the most attractive pathways for their use and the policy measures that could support them. Given the involvement of PSI in the ECOGAS project, especial emphasis is put on the production of bio-SNG from wood via gasification and methanation of syngas and on hydrothermal gasification of woody biomass. Of specific interest as weIl is the fraction of fuel used in passenger cars that could be produced by locally harvested wood. The report is organized as follows: Section 2 presents a brief description of the MARKAL model. Section 3 describes the results of the base case scenario, which represents a plausible, 'middle-of-the-road' development of the Swiss energy system. Section 4 discusses results illustrating the conditions under which the wood-based methanation technology could become competitive in the Swiss energy market, the role of oil and gas prices, subsidies to methanation technologies and the introduction of a competing technology, namely the wood-based Fischer-Tropsch synthesis. FinaIly, section 5 outlines some conclusions from this analysis. (author)

Temperature effects on wood anatomy, wood density, photosynthesis and biomass partitioning of Eucalyptus grandis seedlings.

Science.gov (United States)

Thomas, D S; Montagu, K D; Conroy, J P

2007-02-01

Wood density, a gross measure of wood mass relative to wood volume, is important in our understanding of stem volume growth, carbon sequestration and leaf water supply. Disproportionate changes in the ratio of wood mass to volume may occur at the level of the whole stem or the individual cell. In general, there is a positive relationship between temperature and wood density of eucalypts, although this relationship has broken down in recent years with wood density decreasing as global temperatures have risen. To determine the anatomical causes of the effects of temperature on wood density, Eucalyptus grandis W. Hill ex Maiden seedlings were grown in controlled-environment cabinets at constant temperatures from 10 to 35 degrees C. The 20% increase in wood density of E. grandis seedlings grown at the higher temperatures was variously related to a 40% reduction in lumen area of xylem vessels, a 10% reduction in the lumen area of fiber cells and a 10% increase in fiber cell wall thickness. The changes in cell wall characteristics could be considered analogous to changes in carbon supply. Lumen area of fiber cells declined because of reduced fiber cell expansion and increased fiber cell wall thickening. Fiber cell wall thickness was positively related to canopy CO2 assimilation rate (Ac), which increased 26-fold because of a 24-fold increase in leaf area and a doubling in leaf CO2 assimilation rate from minima at 10 and 35 degrees C to maxima at 25 and 30 degrees C. Increased Ac increased seedling volume, biomass and wood density; but increased wood density was also related to a shift in partitioning of seedling biomass from roots to stems as temperature increased.

Durable protection of the surface of wood used outdoors: material constraints, problems and approaches to solutions

Directory of Open Access Journals (Sweden)

Merlin A.

2018-01-01

Full Text Available The aesthetic durability of wooden structures is a major challenge for the use of this material in construction. Wood is used for its technical performances but also for its architectural qualities and its aesthetic perception. The premature aging of the wooden structures is detrimental because these disorders, even if they do not affect the strength of the structures, are mostly irremediable. The surface protection of wood is generally ensured by the use of a finish, whose essential role is to protect wood from climatic aggressions (water, solar radiation, oxygen, .... The secondary wood processing industry consists of a series of manufacturing and processing activities, each containing a portion of the added value of the product. The application of a finish on a wood-based work is usually the last and most visible step in this value chain.In outdoor use, the protection of the wood surface with transparent finishes is not yet sufficiently durable to be able to compete with materials used in industrial carpentry such as PVC or aluminum. Opaque finishes generally provide more durable protection but they mask the appearance of the wood sought by users.With the aim of positioning wood in this construction sector, research on transparent finishes has focused on the efficiency and improvement of the durability of the protection of the surface appearance of structures. Faced with climatic aggressions, the optimum conservation of a structure is not only linked to the performance of the finish but also to the characteristics of the wood material. In particular, in order to fulfill its protective function, the finish film must be able to follow the dimensional variations of the wood it covers without breaking and without detachment. In addition to the criteria for the effectiveness of finishes in the protection of structures, the environmental impact must be considered with increasing attention. Currently, more than 80% of composite or solid wood

The central role of wood biology in understanding the durability of wood-coating interactions

Science.gov (United States)

Alex C. Wiedenhoeft

2007-01-01

To design effectively for durability, one must actively and honestly assess the material properties and limitations of each of the components in the design system; wood or wood composite, and the coating. Inasmuch as wood coatings are manufactured to specified tolerances from known materials, we have control of that component of the system. Compared to manmade...

Wood as a home heating fuel

International Nuclear Information System (INIS)

Wood, K.

1991-01-01

This article describes the development of clean-burning technology in three types of wood-burning appliances: catalytic, non-catalytic, and pellet stoves. A recent study by the Washington State Energy Extension Office concluded that in homes that use both electricity and wood, 73 megawatts of electricity/yr were saved by using wood. Since wood-burning stoves can now meet air quality standards, wood could be considered to be a greenhouse-neutral fuel if more trees are planted as they are consumed

Microbial Communities in Sunken Wood Are Structured by Wood-Boring Bivalves and Location in a Submarine Canyon

Science.gov (United States)

Fagervold, Sonja K.; Romano, Chiara; Kalenitchenko, Dimitri; Borowski, Christian; Nunes-Jorge, Amandine; Martin, Daniel; Galand, Pierre E.

2014-01-01

The cornerstones of sunken wood ecosystems are microorganisms involved in cellulose degradation. These can either be free-living microorganisms in the wood matrix or symbiotic bacteria associated with wood-boring bivalves such as emblematic species of Xylophaga, the most common deep-sea woodborer. Here we use experimentally submerged pine wood, placed in and outside the Mediterranean submarine Blanes Canyon, to compare the microbial communities on the wood, in fecal pellets of Xylophaga spp. and associated with the gills of these animals. Analyses based on tag pyrosequencing of the 16S rRNA bacterial gene showed that sunken wood contained three distinct microbial communities. Wood and pellet communities were different from each other suggesting that Xylophaga spp. create new microbial niches by excreting fecal pellets into their burrows. In turn, gills of Xylophaga spp. contain potential bacterial symbionts, as illustrated by the presence of sequences closely related to symbiotic bacteria found in other wood eating marine invertebrates. Finally, we found that sunken wood communities inside the canyon were different and more diverse than the ones outside the canyon. This finding extends to the microbial world the view that submarine canyons are sites of diverse marine life. PMID:24805961

Effects of Chemical Curing Temperature and Time on the Properties of Liquefied Wood based As-cured Precursors and Carbon Fibers

Directory of Open Access Journals (Sweden)

Junbo Shang

2015-09-01

Full Text Available Liquefied wood based as-cured precursors and carbon fibers prepared by different chemical curing processes were carried out to investigate the effects of curing temperature and time on the thermostability and microstructure of liquefied wood based precursors, the tensile strength of carbon fibers as well. The primary fibers can be converted into precursors with high performance by directly heating at target curing temperature. With the temperature and duration increasing, the numbers of methylene bonds in precursors increased, resulting in the enhancement of cross-linkages among molecular chains and then the improvement of thermostability of precursors. Carbon fibers prepared from as-cured precursors (curing temperature 95 oC, curing time 3h had the minimum value of the average interlayer spacing (d002, it also showed the highest tensile strength, almost 800 MPa, which can be classified as fibers of general grade.

The beta strength function structure in β+ decay of lutetium, thulium and cesium isotopes

International Nuclear Information System (INIS)

Alkhazov, G.D.; Bykov, A.A.; Vitman, V.D.; Naumov, Yu.V.; Orlov, S.Yu.

1981-01-01

The spectra of total γ-absorption in the decays of some Lutecium, Thulium and Cesium isotopes have been measured. The probabilities for level population in the decay of the isotopes have been determined. The deduced beta strength functions reveal pronounced structure. Calculations of the strength functions using the Saxon-Woods potential and the residual Gamow-Teller interaction are presented. It is shown that in β + decay of light Thulium and Cesium isotopes the strength function comprises more than 70% of the Gamow-Teller excitations with μsub(tau) = +1. This result is the first direct observation of the Gamow-Teller resonance in β + decay of nuclei with Tsub(z) > O. (orig.)

Application of molecular genetic methods for identification of wood-decaying fungi in wood constructions

Directory of Open Access Journals (Sweden)

Elena Bobeková

2008-01-01

Full Text Available The aim of the paper is to evaluate the utilization of molecular biology methods for detection of wood decaying fungi directly from decomposed wood using a commercial DNA extraction kit developed for soil substrates (PowerSoil™ DNA isolation kit. The experiment based on dry rot fungus (Serpula lacrymans detection from inoculated wooden pieces under laboratory conditions was followed by field detection of wood-decaying fungi from wood structures on building constructions. Fungal DNA was identified using the PCR–based methods including species-specific PCR and sequencing of amplified ITS region of ribosomal DNA.

Wood plastic combination

International Nuclear Information System (INIS)

Cunanan, S.A.; Bonoan, L.S.; Verceluz, F.P.; Azucena, E.A.

1976-03-01

The purpose of this study is to improve the physical and mechaniproperties of local inferior quality wood species by radiation-induced graft polymerization with plastic monomers. The process involves the following: 1) Preparation of sample; 2) Impregnation of sample with the monomers; 3) Irradiation of the impregnated sample with the use of 20,000 curie Co-60 as gamma-source; 4) Drying of irradiated sample to remove the unpolymerized monomer. Experimentation on different wood species were undertaken and the results given. From the results obtained, it can be concluded that the monomers systems MMA, MMA-USP, and styrene-USP are suitable for graft polymerization with the wood species almon, apitong, bagtikan, mayapis, red lauan, and tanguile. This is shown by their maximum conversion value which range from 86% to 96% with the optimum dose range of 1 to 2 Mrads. However, in the application of WPC process, properties that are required in a given wood product must be considered, thus aid in the selection of the monomer system to be used with a particular wood species. Some promising applications of WPC is in the manufacture of picker sticks, shuttles, and bobbins for the textile industry. However, there is a need for a pilot plant scale study so that an economic assessment of the commercial feasibility of this process can be made

The case for wood-fuelled heating

International Nuclear Information System (INIS)

Bent, Ewan

2001-01-01

This article looks at the wood heating industry in the UK and examines the heat market and the growth potential in the domestic, public, agricultural and commercial sectors. The current status of wood-fueled heating technology is considered, along with log and chip boilers, and the use of pellet fuel. The economics of wood-fuelled heating, the higher level of utilisation of wood-fuelled heating by utilities in northern European countries compared with the UK, and the barriers to the exploitation of wood fuelled heating are examined

Bacterial community succession in pine-wood decomposition

Directory of Open Access Journals (Sweden)

Anna eKielak

2016-03-01

Full Text Available Though bacteria and fungi are common inhabitants of decaying wood, little is known about the relationship between bacterial and fungal community dynamics during natural wood decay. Based on previous studies involving inoculated wood blocks, strong fungal selection on bacteria abundance and community composition was expected to occur during natural wood decay. Here we focused on bacterial and fungal community compositions in pine wood samples collected from dead trees in different stages of decomposition. We showed that bacterial communities undergo less drastic changes than fungal communities during wood decay. Furthermore, we found that bacterial community assembly was a stochastic process at initial stage of wood decay and became more deterministic in later stages, likely due to environmental factors. Moreover, composition of bacterial communities did not respond to the changes in the major fungal species present in the wood but rather to the stage of decay reflected by the wood density. We concluded that the shifts in the bacterial communities were a result of the changes in wood properties during decomposition and largely independent of the composition of the wood-decaying fungal communities.

Macrophotographic wood atlas of Annonaceae.

NARCIS (Netherlands)

Koek-Noorman, J.; Westra, L.I.T.

2012-01-01

In this article, a general description of the microscopic wood anatomy of Annonaceae is given. We provide a description of the wood anatomical features of the family and of all subfamilies and tribes, all from material in the Utrecht Wood collection. Hand-lens images can be an important help in

The challenge of bonding treated wood

Science.gov (United States)

Charles R. Frihart

2004-01-01

Wood products are quite durable if exposure to moisture is minimized; however, most uses of wood involve considerable exposure to moisture. To preserve the wood, chemicals are used to minimize moisture pickup, to prevent insect attack, and/or to resist microbial growth. The chemicals used as preservatives can interfere with adhesive bonds to wood. Given the many...

FIRE INSURANCE AND WOOD SCHOOL BUILDINGS.

Science.gov (United States)

PURCELL, FRANK X.

A COMPARISON OF FIRE INSURANCE COSTS OF WOOD, MASONRY, STEEL AND CONCRETE STRUCTURES SHOWS FIRE INSURANCE PREMIMUMS ON WOOD STRUCTURES TEND TO BE HIGHER THAN PREMIUMS ON MASONRY, STEEL AND CONCRETE BUILDINGS, HOWEVER, THE INITIAL COST OF THE WOOD BUILDINGS IS LOWER. DATA SHOW THAT THE SAVINGS ACHIEVED IN THE INITIAL COST OF WOOD STRUCTURES OFFSET…

Effect of environmental conditions on the mechanical properties and fungal degradation of polycaprolactone/microcrystalline cellulose/wood flour composites

Science.gov (United States)

Ronald Sabo; Liwei Jin; Nicole Stark; Rebecca E. Ibach

2013-01-01

Polycaprolactone (PCL) filled with microcrystalline cellulose (MCC), wood flour (WF), or both were characterized before and after exposure to various environmental conditions for 60 days. PCL/WF composites had the greatest tensile strength and modulus compared to neat PCL or PCL composites containing MCC. Electron microscopy indicated better adhesion between WF...

Qualidade de juntas coladas com lâminas de madeira oriundas de três regiões do tronco de Eucalyptus grandis, Eucalyptus saligna e Pinus elliottii Quality of wood joints glued with wood veneers from three trunk regions of Eucalyptus grandis, Eucalyptus saligna and Pinus elliottii

Directory of Open Access Journals (Sweden)

Benedito Rocha Vital

2006-08-01

Full Text Available Este experimento teve como objetivo avaliar a resistência de juntas coladas formadas pelas combinações de lâminas provenientes de três posições no tronco da madeira de Eucalyptus grandis, Eucalyptus saligna e Pinus elliottii. Foram empregados adesivos à base de poliacetato de vinila de média e alta viscosidade e resorcinol-formaldeído nas gramaturas de 150 g/m², em face simples para o poliacetato de vinila de média e alta viscosidades e 300 g/m², em face dupla, para o adesivo resorcinólico. O teor médio de umidade das lâminas, no momento da colagem, foi igual a 14%. Os valores médios mais elevados de resistência ao cisalhamento foram obtidos nas juntas produzidas com madeira de Eucalyptus saligna, coladas com adesivos de poliacetato de média viscosidade e resorcinol-formaldeído. A maior porcentagem de falha profunda na madeira foi obtida em juntas de madeira de Pinus elliottii, unidas com adesivo de poliacetato de alta viscosidade, seguidas das juntas de Eucalyptus grandis e coladas com adesivo de poliacetato de média viscosidade. As combinações de lâminas oriundas das seguintes posições no tronco: medula e casca, intermediária e casca e casca e casca resultaram em linhas de cola com maiores resistências ao cisalhamento.The objective of this work was to evaluate the shear strength of glued wood joints from pith, outer and intermediary wood of Eucalyptus saligna, Eucalyptus grandis and Pinus elliottii. High and medium viscosity polyvinyl acetate and resorcinol-phenol adhesives were applied at spread rate of 150 g/m² in single line and at spread rate of 300 g/m² in double glue line for the resorcinolic adhesive. The mean wood moisture content was 14%. Higher shear strength was obtained with Eucalyptus saligna veneer glued with medium viscosity polyvinyl resorcinolic adhesive. The highest percentage of wood failure was found on Pinus elliottii veneer glued with high viscosity polyvinyl acetate adhesive followed by

Physical and mechanical properties of bio-composites from wood particles and liquefied wood resin

Science.gov (United States)

Hui Pan; Todd F. Shupe; Chung-Yun Hse

2009-01-01

Compression molded composites were made from wood particles and a liquefied wood/phenol/formaldehyde co-condensed resin. Based on our previous research, a phenol to wood (P/W) ratio of 2/1 was chosen for this study. The two experimental variables selected were: 1) liquefaction temperature (150o and 180oC) and 2) cooking method (atmospheric and sealed). Panels were...

The wood energy in France

International Nuclear Information System (INIS)

Douard, F.; Oremus, Y.; Garsault-Fabbi, A.

2007-01-01

The program law fixing the energy policy (POPE Law of the 13 july 2005) fixes an objective of 50% of growth for the renewable heat. As this renewable heat is today generated by the biomass, it seems necessary to adjust all the efforts on this sector. This document proposes to takes stock on the wood energy in France. It presents the wood fuels, an evaluation of the Wood-Energy Plan decided by the ADEME in 2000, the wood heat networks, and some example of installations. (A.L.B.)

Production of oil palm (Elaeis guineensis) fronds lignin-derived non-toxic aldehyde for eco-friendly wood adhesive.

Science.gov (United States)

Hazwan Hussin, M; Samad, Noraini Abdul; Latif, Nur Hanis Abd; Rozuli, Nurul Adilla; Yusoff, Siti Baidurah; Gambier, François; Brosse, Nicolas

2018-07-01

Lignocellulosic materials can significantly contribute to the development of eco-friendly wood adhesives. In this work, glyoxal-phenolic resins for plywood were prepared using organosolv lignin, which was isolated from black liquor recovered from organosolv pulping of oil palm fronds (OPF) and considered to be an alternative to phenol. Glyoxal, which is a dialdehyde obtained from several natural resources, was used as substitute for formaldehyde. The structure of organosolv lignin and the resins were characterized by FTIR and NMR, and for thermal stability by TGA and DSC. The resins were further studied for their viscosity, pH, solids content and gel times. The resins performance as wood adhesive was further established from mechanical test in terms of tensile strength and modulus of elasticity (MOE) to obtain the optimum ratios of organosolv lignin, which replaces phenol in organosolv lignin phenol glyoxal (OLPG) resins. The adhesive composition having 50% (w/w) of phenol substituted by organosolv lignin, termed as 50% OLPG showed highest adhesive strength compared to phenol formaldehyde (PF) commercial adhesive. Copyright © 2018 Elsevier B.V. All rights reserved.

LEATHER WASTE VALORISATION THROUGH MATERIAL INNOVATION: SOME PROPERTIES OF LEATHER WOOD FIBREBOARD

Directory of Open Access Journals (Sweden)

Axel M. RINDLER

2015-12-01

Full Text Available Due to the ever-increasing scarcity of resources and raw materials in the wood panels industry, it is imperative to look for suitable alternatives to the established resources. Therefore a combination of the traditionally used and newly explored sources may reveal highly innovative ways. The objective of this study is to provide an insight into the behavior of the material and possible new applications of those fiber/particle wood and waste leather composites. For this reason exclusively fibers of spruce were used for the trials. Wet white (WW leather particles and wet blue (WB leather particles were mixed with the wooden materials for the production of high density fibreboards. Besides the mechanical properties such as the internal bond (IB the bending strength (MOR and modulus of elasticity (MOE was analyzed. Further physical property as thickness swelling after 24h watering was investigated. To analyze how the density influences the behavior under thermal conditions, fiberboards with the densities 500, 700 and 900 kg/m³ were tested. The results of the material properties were influenced by the leather content of the panels. The results for the UF-bonded HDF boards show enhancement of the transverse IB with increasing wet blue leather content, whereas the other mechanical properties decline meanwhile. The thickness swelling showed higher values compared to the wood fibreboard. The results of this study underline the usefulness of integrating leather shavings to HDF and give an overview of their influence in wood fiber materials. The combination of the natural resource wood fiber and the leather waste products (Wet Blue and Wet White gives a very interesting new material, its mechanical properties allow a variety of possible application in future applications.

An assessment of management practices of wood and wood-related wastes in the urban environment

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-02-01

The US Environmental Protection Agency estimates that yard waste{sup 1} accounts for approximately 16% of the municipal solid waste (MSW) stream (US EPA, 1994). Until recently, specific data and related information on this component of the (MSW) stream has been limited. The purposes of this study, phase two of the three-phase assessment of urban wood waste issues, are to assess and describe current alternatives to landfills for urban wood waste management; provide guidance on the management of urban wood waste to organizations that produce or manage wood waste; and clarify state regulatory and policy positions affecting these organizations. For this study, urban wood waste is defined as solid waste generated by tree and landscape maintenance services (public and private). Urban wood waste includes the following materials: unchipped mixed wood, unchipped logs, and unchipped tops and brush; clearing and grubbing waste; fall leaves and grass clippings; and chips and whole stumps. Construction and demolition debris and consumer-generated yard waste are not included in this study. Generators of urban wood waste include various organizations; municipal, county, and commercial tree care divisions; nurseries, orchards, and golf courses; municipal park and recreation departments; and electric and telephone utility power line maintenance, excavator and land clearance, and landscape organizations. (1) US EPA defines yard waste as ''yard trimmings'' which includes ''grass, leaves and tree brush trimmings from residential, institutional, and commercial sources.''

Complex geometries in wood

DEFF Research Database (Denmark)

Tamke, Martin; Ramsgaard Thomsen, Mette; Riiber Nielsen, Jacob

2009-01-01

The versatility of wood constructions and traditional wood joints for the production of non standard elements was in focus of a design based research. Herein we established a seamless process from digital design to fabrication. A first research phase centered on the development of a robust...... parametric model and a generic design language a later explored the possibilities to construct complex shaped geometries with self registering joints on modern wood crafting machines. The research was carried out as collaboration with industrial partners....

Experimental Investigation and Taguchi Optimisation of Drilling Properties on Teak Wood Reinforced Epoxy Resin

Science.gov (United States)

Lilly Mercy, J.; Shaqir Tanvir, Mohamed; Swaroopkanth, K.

2017-05-01

The drilling properties of teak reinforced epoxy resin composite are explored in this work. The thrust force and temperature during the drilling process was found and optimised. Nine holes were drilled in accordance with L9 orthogonal array on Medium Density Fibre board and Teak wood reinforced epoxy composite board and the thrust force and temperature induced during drilling is measured. Drilling experiments were conducted using CNC Vertical drilling machine and the thrust force was measured using dynamometer and temperature using infra-red thermometer. The experiments were conducted with varying levels of spindle speed and feed rate and optimised using Taguchi optimisation. It was observed that higher thrust and temperature were observed while drilling teak wood composite due to the high mechanical strength of teak wood. The hard and brittle properties of the resin seemed to be more pronounced in the composite. The experimental results were optimised to find the best combination of input parameters for reduced thrust and temperature. When speed increases, thrust force decreases and temperature increases. When feed increases, thrust force increases and temperature decreases. Experimental findings encouragesto use teak wood reinforced epoxy resin as a substitute for the traditionally used Medium Density Fibre Board. The percentage of mixing of teak dust can be increased with various resin combinations to arrive at the best suitable combination for obtaining optimal mechanical properties.

Tracing nitrogen accumulation in decaying wood and examining its impact on wood decomposition rate

Science.gov (United States)

Rinne, Katja T.; Rajala, Tiina; Peltoniemi, Krista; Chen, Janet; Smolander, Aino; Mäkipää, Raisa

2016-04-01

Decomposition of dead wood, which is controlled primarily by fungi is important for ecosystem carbon cycle and has potentially a significant role in nitrogen fixation via diazotrophs. Nitrogen content has been found to increase with advancing wood decay in several studies; however, the importance of this increase to decay rate and the sources of external nitrogen remain unclear. Improved knowledge of the temporal dynamics of wood decomposition rate and nitrogen accumulation in wood as well as the drivers of the two processes would be important for carbon and nitrogen models dealing with ecosystem responses to climate change. To tackle these questions we applied several analytical methods on Norway spruce logs from Lapinjärvi, Finland. We incubated wood samples (density classes from I to V, n=49) in different temperatures (from 8.5oC to 41oC, n=7). After a common seven day pre-incubation period at 14.5oC, the bottles were incubated six days in their designated temperature prior to CO2 flux measurements with GC to determine the decomposition rate. N2 fixation was measured with acetylene reduction assay after further 48 hour incubation. In addition, fungal DNA, (MiSeq Illumina) δ15N and N% composition of wood for samples incubated at 14.5oC were determined. Radiocarbon method was applied to obtain age distribution for the density classes. The asymbiotic N2 fixation rate was clearly dependent on the stage of wood decay and increased from stage I to stage IV but was substantially reduced in stage V. CO2 production was highest in the intermediate decay stage (classes II-IV). Both N2 fixation and CO2 production were highly temperature sensitive having optima in temperature 25oC and 31oC, respectively. We calculated the variation of annual levels of respiration and N2 fixation per hectare for the study site, and used the latter data together with the 14C results to determine the amount of N2 accumulated in wood in time. The proportion of total nitrogen in wood

How to make a beetle out of wood: multi-elemental stoichiometry of wood decay, xylophagy and fungivory.

Science.gov (United States)

Filipiak, Michał; Weiner, January

2014-01-01

The majority of terrestrial biomass is wood, but the elemental composition of its potential consumers, xylophages, differs hugely from that of wood. This causes a severe nutritional imbalance. We studied the stoichiometric relationships of 11 elements (C, N, P, K, Ca, Mg, Fe, Zn, Mn, Cu, Na) in three species of pine-xylem-feeding insects, Stictoleptura rubra, Arhopalus rusticus (Coleoptera, Cerambycidae) and Chalcophora mariana (Coleoptera, Buprestidae), to elucidate their mechanisms of tissue growth and to match their life histories to their dietary constraints. These beetles do not differ from other Coleoptera in their absolute elemental compositions, which are approximately 1000 (N), 100 (P, Cu) and 50 (K, Na) times higher than in dead but undecayed pine wood. This discrepancy diminishes along the wood decay gradient, but the elemental concentrations remain higher by an order of magnitude in beetles than in highly decayed wood. Numerical simulation of the life history of S. rubra shows that feeding on nutrient-poor undecayed wood would extend its development time to implausible values, whereas feeding on highly decomposed wood (heavily infected with fungi) would barely balance its nutritional budget during the long development period of this species. The changes in stoichiometry indicate that the relative change in the nutrient levels in decaying wood cannot be attributed solely to carbon loss resulting from decomposer respiration: the action of fungi substantially enriches the decaying wood with nutritional elements imported from the outside of the system, making it a suitable food for wood-eating invertebrates.

Wood Quality of Acacia Hybrid and Second-Generation Acacia mangium

Directory of Open Access Journals (Sweden)

Ismail Jusoh

2013-11-01

Full Text Available Two new tree variants, namely Acacia hybrid and second-generation Acacia mangium, have been introduced in plantation forests in Sarawak, Malaysia, and their wood qualities were examined. The mean basic density of Acacia hybrid was comparable with Acacia mangium. However basic density and strength properties of second-generation A. mangium were significantly lower compared to Acacia hybrid. The mean fibre length and fibre wall thickness in the hybrid were found to be greater than that of second-generation A. mangium. Fibre diameter and fibre lumen diameter of Acacia hybrid were smaller compared to second-generation A. mangium. Runkel and slenderness ratios of Acacia hybrid and second-generation A. mangium fibres showed that they were suitable for pulp and paper production. Acacia hybrid was more resistant to Coptotermes curvignathus attack than second-generation A. mangium. A laboratory soil block test showed that Acacia hybrid and second-generation A. mangium were moderately durable timbers. In summary, marked differences in wood properties and qualities were observed between Acacia hybrid and second-generation A. mangium.

Photodegradation of wood and depth profile analysis

International Nuclear Information System (INIS)

Kataoka, Y.

2008-01-01

Photochemical degradation is a key process of the weathering that occurs when wood is exposed outdoors. It is also a major cause of the discoloration of wood in indoor applications. The effects of sunlight on the chemical composition of wood are superficial in nature, but estimates of the depth at which photodegradation occurs in wood vary greatly from 80 microm to as much as 2540 mic rom. Better understanding of the photodegradation of wood through depth profile analysis is desirable because it would allow the development of more effective photo-protective treatments that target the surface layers of wood most susceptible to photodegradation. This paper briefly describes fundamental aspects of photodegradation of wood and reviews progress made in the field of depth profile study on the photodegradation of wood. (author)

Robert Williams Wood: pioneer of invisible light.

Science.gov (United States)

Sharma, Shruti; Sharma, Amit

2016-03-01

The Wood's lamp aids in the diagnosis of multiple infectious, inflammatory and neoplastic dermatologic conditions. Although the Wood's lamp has many applications, which have improved both the diagnosis and management of disease, the man credited for its invention is relatively unknown in medicine. Robert Williams Wood, a prominent physicist of the early 20th century, is credited for the invention of the Wood's lamp. Wood was the father of infrared and ultraviolet photography and made significant contributions to other areas in optics and spectroscopy. Wood's work encompassed the formative years of American Physics; he published over 200 original papers over his lifetime. A few years after the invention of the Wood's lamp for ultraviolet photography, physicians in Europe adopted the Wood's lamp for dermatologic applications. Wood's lamp remains popular in clinics globally, given its ease of use and ability to improve diagnostic precision. © 2016 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Sodium alginate adhesives as binders in wood fibers/textile waste fibers biocomposites for building insulation.

Science.gov (United States)

Lacoste, Clément; El Hage, Roland; Bergeret, Anne; Corn, Stéphane; Lacroix, Patrick

2018-03-15

Alginate derived from seaweed is a natural polysaccharide able to form stable gel through carbohydrate functional groups largely used in the food and pharmaceutical industry. This article deals with the use of sodium alginate as an adhesive binder for wood fibres/textile waste fibres biocomposites. Several aldehyde-based crosslinking agents (glyoxal, glutaraldehyde) were compared for various wood/textile waste ratios (100/0, 50/50, 60/40, 70/30 and 0/100 in weight). The fully biomass derived composites whose properties are herewith described satisfy most of the appropriate requirements for building materials. They are insulating with a thermal conductivity in the range 0.078-0.089 W/m/K for an average density in the range 308-333 kg/m3 according to the biocomposite considered. They are semi-rigid with a maximal mechanical strength of 0.84 MPa under bending and 0.44 MPa under compression for 60/40 w/w wood/textile waste biocomposites with a glutaraldehyde crosslinking agent. Copyright © 2017 Elsevier Ltd. All rights reserved.

Wood Specific Gravity Variations and Biomass of Central African Tree Species: The Simple Choice of the Outer Wood.

Directory of Open Access Journals (Sweden)

Jean-François Bastin

Full Text Available Wood specific gravity is a key element in tropical forest ecology. It integrates many aspects of tree mechanical properties and functioning and is an important predictor of tree biomass. Wood specific gravity varies widely among and within species and also within individual trees. Notably, contrasted patterns of radial variation of wood specific gravity have been demonstrated and related to regeneration guilds (light demanding vs. shade-bearing. However, although being repeatedly invoked as a potential source of error when estimating the biomass of trees, both intraspecific and radial variations remain little studied. In this study we characterized detailed pith-to-bark wood specific gravity profiles among contrasted species prominently contributing to the biomass of the forest, i.e., the dominant species, and we quantified the consequences of such variations on the biomass.Radial profiles of wood density at 8% moisture content were compiled for 14 dominant species in the Democratic Republic of Congo, adapting a unique 3D X-ray scanning technique at very high spatial resolution on core samples. Mean wood density estimates were validated by water displacement measurements. Wood density profiles were converted to wood specific gravity and linear mixed models were used to decompose the radial variance. Potential errors in biomass estimation were assessed by comparing the biomass estimated from the wood specific gravity measured from pith-to-bark profiles, from global repositories, and from partial information (outer wood or inner wood.Wood specific gravity profiles from pith-to-bark presented positive, neutral and negative trends. Positive trends mainly characterized light-demanding species, increasing up to 1.8 g.cm-3 per meter for Piptadeniastrum africanum, and negative trends characterized shade-bearing species, decreasing up to 1 g.cm-3 per meter for Strombosia pustulata. The linear mixed model showed the greater part of wood specific gravity

Wood Specific Gravity Variations and Biomass of Central African Tree Species: The Simple Choice of the Outer Wood.

Science.gov (United States)

Bastin, Jean-François; Fayolle, Adeline; Tarelkin, Yegor; Van den Bulcke, Jan; de Haulleville, Thales; Mortier, Frederic; Beeckman, Hans; Van Acker, Joris; Serckx, Adeline; Bogaert, Jan; De Cannière, Charles

2015-01-01

Wood specific gravity is a key element in tropical forest ecology. It integrates many aspects of tree mechanical properties and functioning and is an important predictor of tree biomass. Wood specific gravity varies widely among and within species and also within individual trees. Notably, contrasted patterns of radial variation of wood specific gravity have been demonstrated and related to regeneration guilds (light demanding vs. shade-bearing). However, although being repeatedly invoked as a potential source of error when estimating the biomass of trees, both intraspecific and radial variations remain little studied. In this study we characterized detailed pith-to-bark wood specific gravity profiles among contrasted species prominently contributing to the biomass of the forest, i.e., the dominant species, and we quantified the consequences of such variations on the biomass. Radial profiles of wood density at 8% moisture content were compiled for 14 dominant species in the Democratic Republic of Congo, adapting a unique 3D X-ray scanning technique at very high spatial resolution on core samples. Mean wood density estimates were validated by water displacement measurements. Wood density profiles were converted to wood specific gravity and linear mixed models were used to decompose the radial variance. Potential errors in biomass estimation were assessed by comparing the biomass estimated from the wood specific gravity measured from pith-to-bark profiles, from global repositories, and from partial information (outer wood or inner wood). Wood specific gravity profiles from pith-to-bark presented positive, neutral and negative trends. Positive trends mainly characterized light-demanding species, increasing up to 1.8 g.cm-3 per meter for Piptadeniastrum africanum, and negative trends characterized shade-bearing species, decreasing up to 1 g.cm-3 per meter for Strombosia pustulata. The linear mixed model showed the greater part of wood specific gravity variance was

Preservation of forest wood chips

Energy Technology Data Exchange (ETDEWEB)

Kofman, P.D.; Thomsen, I.M.; Ohlsson, C.; Leer, E.; Ravn Schmidt, E.; Soerensen, M.; Knudsen, P.

1999-01-01

As part of the Danish Energy Research Programme on biomass utilisation for energy production (EFP), this project concerns problems connected to the handling and storing of wood chips. In this project, the possibility of preserving wood chips of the Norway Spruce (Picea Abies) is addressed, and the potential improvements by anaerobic storage are tested. Preservation of wood chips aims at reducing dry matter losses from extensive heating during storage and to reduce production of fungal spores. Fungal spores pose a health hazards to workers handling the chips. Further the producers of wood chips are interested in such a method since it would enable them to give a guarantee for the delivery of homogeneous wood chips also during the winter period. Three different types of wood chips were stored airtight and further one of these was stored in accordance with normal practise and use as reference. The results showed that airtight storage had a beneficial impact on the quality of the chips: no redistribution of moisture, low dry matter losses, unfavourable conditions for microbial activity of most fungi, and the promotion of yeasts instead of fungi with airborne spores. Likewise the firing tests showed that no combustion problems, and no increased risk to the environment or to the health of staff is caused by anaerobic storage of wood chips. In all, the tests of the anaerobic storage method of forest wood chips were a success and a large-scale test of the method will be carried out in 1999. (au)

Analysis of Selected Properties of Fibreboard Panels Manufactured from Wood and Leather Using the Near Infrared Spectroscopy

Directory of Open Access Journals (Sweden)

Kerstin Wagner

2015-01-01

Full Text Available This paper deals with the characterization of the properties of wood fibres leather shavings composite board by using the near infrared spectroscopy (NIRS and multivariate data analysis. In this study fibreboards were manufactured with different leather amounts by using spruce fibres, as well as vegetable and mineral tanned leather shavings (wet white and wet blue. The NIR spectroscopy was used to analyse the raw materials as well as the wood leather fibreboards. Moreover, the physical and mechanical features of the wood leather composite fibreboards were determined to characterize their properties for the further data analysis. The NIR spectra were analysed by univariate and multivariate methods using the Principal Component Analysis (PCA and the Partial Least Squares Regression (PLSR method. These results demonstrate the potential of FT-NIR spectroscopy to estimate the physical and mechanical properties (e.g., bending strength. This phenomenon provides a possibility for quality assurance systems by using the NIRS.

Wood pellets in a power plant - mixed combustion of coal and wood pellets

International Nuclear Information System (INIS)

Nupponen, M.

2001-01-01

The author reviews in his presentation the development of Turku Energia, the organization of the company, the key figures of the company in 2000, as well as the purchase of energy in 2000. He also presents the purchase of basic heat load, the energy production plants of the company, the sales of heat in 2000, the emissions of the plants, and the fuel consumption of the plants in 2000. The operating experiences of the plants are also presented. The experiences gained in Turku Energia on mixed combustion of coal and wood pellets show that the mixing ratios, used at the plants, have no effect on the burning properties of the boiler, and the use of wood pellets with coal reduce the SO 2 and NO x emissions slightly. Simultaneously the CO 2 share of the wood pellets is removed from the emissions calculations. Several positive effects were observed, including the disappearance of the coal smell of the bunker, positive publicity of the utilization of wood pellets, and the subsidies for utilization of indigenous fuels in power generation. The problems seen include the tendency of wood pellets to arc the silos, especially when the pellets include high quantities of dust, and the loading of the trucks and the pneumatic unloading of the trucks break the pellets. Additionally the wood pellets bounce on the conveyor so they drop easily from the conveyor, the screw conveyors designed for conveying grain are too weak and they get stuck easily, and static electricity is easily generated in the plastic pipe used as the discharge pipe for wood pellet (sparkling tendency). This disadvantage has been overcome by using metal net and grounding

Continued growth expected for wood energy despite turbulence of the economic crisis : wood energy markets, 2008-2009

Science.gov (United States)

Rens Hartkamp; Bengt Hillring; Warren Mabee; Olle Olsson; Kenneth Skog; Henry Spelter; Johan Vinterback; Antje Wahl

2009-01-01

The economic crisis has not reduced the demand for wood energy, which is expected to continue to grow. The downturn in sawmill production caused a shortage of raw material supply for wood pellet producers. With decreased demand for pulpwood-quality roundwood for wood and paper products in 2009, some pulpwood is being converted into wood energy. Economies of scale are...

Wood's lamp illumination (image)

Science.gov (United States)

A Wood's lamp emits ultraviolet light and can be a diagnostic aid in determining if someone has a fungal ... is an infection on the area where the Wood's lamp is illuminating, the area will fluoresce. Normally ...

Robert Wood Johnson Foundation

Science.gov (United States)

Robert Wood Johnson Foundation Search How We Work Our Focus Areas About RWJF Search Menu How We Work Grants ... Learn more For Grantees and Grantseekers The Robert Wood Johnson Foundation funds a wide array of programs ...

Advantages of the use of energy wood

International Nuclear Information System (INIS)

Kaerhae, K.; Aarnio, J.; Maekinen, P.

2000-01-01

According to the Regional Forestry Associations it would be possible to develop the harvesting of energy wood by increasing the use of it. The study was made at the areas of 34 regional forestry associations as an inquiry to the executive managers, as well as the persons responsible for timber trade, harvesting or regional affairs. The inquiries studied the use of energy wood and the user of them at the areas of the associations, as well as the amounts of harvesting and the realization of it. Only a third of the associations have large energy wood consuming plants (using more than 500 m 3 energy wood per year). The closest large energy wood consuming plant was in the average 31 km from the office of the association. The average energy wood use of the plant was 20 000 m 3 /a, the variation being 700 - 200 000 m 3 /a. The energy wood purchase range of the plants varied from few kilometers to hundred kilometers, the average being 47 km. Most of the energy wood was harvested from forest regeneration areas. Some of the energy wood is also harvested from young forest maintenance and thinning areas. The estimated harvesting of energy wood in 1999 was 6300 m 3 . A part of the energy wood is used for heating the farms and other small real estates, and a part is used for heating larger buildings like schools, hospitals, factories. The fees to the associations for purchase of energy wood varied significantly. The range was 2.00 - 11.00 FIM/m 3 . One association charged 300 FIM/parcel, and in one association the price depend on the amount of wood acquired from the lot, the unit price being 0.5 FIM/m 3 . It appeared that the associations estimated the use of energy wood to increase. The level in 1999 was 6300 m 3 and it is estimated to increase to 14 300 m 3 in 2005. The associations estimated that the levels can only be achieved if the stumpage price of energy wood may not be 0.0 FIM. Even a marginal price would lead to an increased harvesting of energy wood. The associations

Inoculation Expedition of Agar wood

International Nuclear Information System (INIS)

Peng, C.S.; Mohd Fajri Osman; Rusli Zakaria

2015-01-01

Inoculation expedition of agar wood is a main field works for researcher in Nuclear Malaysia to prove the real inoculation of agar wood in real jungle. These expeditions was conducted fourth times in the jungles of Malaysia including Gunung Tebu in Terengganu, Murum in Belaga, Sarawak, Kampung Timbang in Kota Belud, Sabah and Nuclear Malaysia itself. This expedition starts from preparation of samples and equipment, transportation into the jungle, searching and recognition of agar wood and lastly, inoculation of the agar wood. Safety aspects precedence set out in the preparation and implementation of this expedition. (author)

WOOD CELLULAR DENDROCLIMATOLOGY: TESTING NEW PROXIES IN GREAT BASIN BRISTLECONE PINE

Directory of Open Access Journals (Sweden)

Emanuele Ziaco

2016-10-01

Full Text Available Dendroclimatic proxies can be generated from the analysis of wood cellular structures, allowing for a more complete understanding of the physiological mechanisms that control the climatic response of tree species. Century-long (1870-2013 time series of anatomical parameters were developed for Great Basin bristlecone pine (Pinus longaeva D.K. Bailey by capturing strongly contrasted microscopic images through a Confocal Laser Scanning Microscope. Environmental information embedded in wood anatomical series was analyzed in comparison with ring-width series using measures of empirical signal strength. Response functions were calculated against monthly climatic variables to evaluate climate sensitivity of cellular features (e.g. lumen area; lumen diameter for the period 1950-2013. Calibration-verification tests were used to determine the potential to generate long climate reconstructions from these anatomical proxies. A total of eight tree-ring parameters (two ring-width and six chronologies of xylem anatomical parameters were analyzed. Synchronous variability among samples varied among tree-ring parameters, usually decreasing from ring width to anatomical features. Cellular parameters linked to plant hydraulic performance (e.g. tracheid lumen area and radial lumen diameter showed empirical signal strength similar to ring-width series, while noise was predominant in chronologies of lumen tangential width and cell-wall thickness. Climatic signals were different between anatomical and ring-width chronologies, revealing a positive and temporally stable correlation of tracheid size (i.e. lumen and cell diameter with monthly (i.e. March and seasonal precipitation. In particular, tracheid lumen diameter emerged as a reliable moisture indicator and was then used to reconstruct total March-August precipitation from 1870 to 2013. Wood anatomy holds great potential to refine and expand dendroclimatic records by allowing estimates of plant physiological

Characterisation of wood combustion ashes

DEFF Research Database (Denmark)

Maresca, Alberto

The combustion of wood chips and wood pellets for the production of renewable energy in Denmark increased from 5.7 PJ to 16 PJ during the period 2000-2015, and further increases are expected to occur within the coming years. In 2012, about 22,300 tonnes of wood ashes were generated in Denmark....... Currently, these ashes are mainly landfilled, despite Danish legislation allowing their application onto forest and agricultural soils for fertilising and/or liming purposes. During this PhD work, 16 wood ash samples generated at ten different Danish combustion plants were collected and characterised...... for their composition and leaching properties. Despite the relatively large variations in the contents of nutrients and trace metals, the overall levels were comparable to typical ranges reported in the literature for other wood combustion ashes, as well as with regards to leaching. In general, the composition...

P.E.I. wood fuel survey, 1990-91

International Nuclear Information System (INIS)

1991-04-01

In 1991 a wood fuel survey of 450 randomly selected households, representing 1% of the total number of households in Prince Edward Island, was conducted. The survey indicated that 49.8% of the households burned wood, up from 42.1% of households in the 1988-1989 survey. The wood burning households consumed an average of 4.92 cords of wood, consistent with the 4.90 cords in the 1989 survey. The total residential wood consumption was estimated at ca 100,377 cords, an increase from the 89,000 cords used in 1988-89. Wood cutters represented 23.4% of respondents, with buyers representing 25.4% of respondents. The wood burning appliances used by the respondents were: airtight wood stove 39.9%, wood furnace 22.5%, kitchen wood stove 15.7%, combined wood/oil furnace 8.9%, Franklin/non-airtight 4.4%, Kemac unit 4.4%, fireplace insert 3.1%, and open fireplace 1%. The most frequent response among rural wood users cited price as an advantage of wood fuel, while the most frequent response of urban users cited the quality of the heat. 9 figs., 47 tabs

Wood for the trees

Directory of Open Access Journals (Sweden)

Rob Garbutt

2013-10-01

Full Text Available Our paper focuses on the materiality, cultural history and cultural relations of selected artworks in the exhibition Wood for the trees (Lismore Regional Gallery, New South Wales, Australia, 10 June – 17 July 2011. The title of the exhibition, intentionally misreading the aphorism “Can’t see the wood for the trees”, by reading the wood for the resource rather than the collective wood[s], implies conservation, preservation, and the need for sustaining the originating resource. These ideas have particular resonance on the NSW far north coast, a region once rich in rainforest. While the Indigenous population had sustainable practices of forest and land management, the colonists deployed felling and harvesting in order to convert the value of the local, abundant rainforest trees into high-value timber. By the late twentieth century, however, a new wave of settlers launched a protest movements against the proposed logging of remnant rainforest at Terania Creek and elsewhere in the region. Wood for the trees, curated by Gallery Director Brett Adlington, plays on this dynamic relationship between wood, trees and people. We discuss the way selected artworks give expression to the themes or concepts of productive labour, nature and culture, conservation and sustainability, and memory. The artworks include Watjinbuy Marrawilil’s (1980 Carved ancestral figure ceremonial pole, Elizabeth Stops’ (2009/10 Explorations into colonisation, Hossein Valamanesh’s (2008 Memory stick, and AñA Wojak’s (2008 Unread book (in a forgotten language. Our art writing on the works, a practice informed by Bal (2002, Muecke (2008 and Papastergiadis (2004, becomes a conversation between the works and the themes or concepts. As a form of material excess of the most productive kind (Grosz, 2008, p. 7, art seeds a response to that which is in the air waiting to be said of the past, present and future.

EFFECTS OF BURN RATE, WOOD SPECIES, MOISTURE CONTENT AND WEIGHT OF WOOD LOADED ON WOODSTOVE EMISSIONS

Science.gov (United States)

The report gives results of tests of four woodstove operating parameters (burn rate, wood moisture, wood load, and wood species) at two levels each using a half factorial experimental test design to determine statistically significant effects on the emission components CO, CO2, p...

Energy wood procurement in connection with conventional wood procurement; Energiapuun hankinnan organisointi muun puunhankinnan yhteydessae - PUUT02

Energy Technology Data Exchange (ETDEWEB)

Maekinen, P. [Finnish Forest Research Institute, Vantaa (Finland)

2001-07-01

The research consisted of two sub-projects. The present role of forestry associations in procurement of energy wood was investigated in the first sub- project. The possibilities and willingness of them to increase the energy wood procurement were also studied. The role of forest machine and forestry service entrepreneurs in procurement of energy wood was investigated in the second sub-project. The effects of energy wood procurement on the operation of the forest machine companies in general were also studied in this sub-project. The sub-project three studied the requirements of the customer companies for the energy wood suppliers. All the material of the sub-projects was collected by personal inquiries. According to the executive directors of the forestry associations the role of the forestry associations in energy wood procurement varied between a by-stander and active participant. Active forestry associations announced the companies for stands available for cutting. They told also that they directed the harvesting to correct sites and deliver stems at the roadside. The role of the forestry association was emphasised especially when the associations on the basis of a letter of attorney carried out the timber trade. It was estimated that in the near future the operation of forest machine entrepreneurs in harvesting of energy wood would increase significantly. From the employment and turnover point of view the role of harvesting of energy wood was not seen as a significant matter. On the other hand, that harvesting of energy wood impede the harvesting of commercial timber was seen as a more significant matter. In the future the end-users of energy wood would like to have more competition in the energy wood markets. However, the energy wood suppliers were desired to be relative large so that the reliability of deliveries could be ensured. Simultaneously as the end-users wanted to decrease the price of forest chips, the machine entrepreneurs estimated the price to

Wood thermoplastic composites

Science.gov (United States)

Daniel F. Caulfield; Craig Clemons; Rodney E. Jacobson; Roger M. Rowell

2005-01-01

The term “wood-plastic composites” refers to any number of composites that contain wood (of any form) and either thermoset or thermoplastic polymers. Thermosets or thermoset polymers are plastics that, once cured, cannot be remelted by heating. These include cured resins, such as epoxies and phenolics, plastics with which the forest products industry is most familiar (...

Effect of Alternative Wood Species and First Thinning Wood on Oriented Strand Board Performance

Directory of Open Access Journals (Sweden)

Fabiane Salles Ferro

2018-01-01

Full Text Available This study aimed to evaluate the feasibility of using and influence of alternative wood species such as Cambará, Paricá, Pinus, and wood from first thinning operations on oriented strand board (OSB physical and mechanical properties. Besides that, an alternative resin, castor oil-based polyurethane, was used to bond the particles, due to the better environmental performance when compared to other resins commonly used worldwide in OSB production. Physical properties such as the moisture content, thickness swelling, and water absorption, both after 2 and 24 hours of water immersion, and mechanical properties such as the modulus of elasticity and resistance in static bending, in major and minor axes, and internal bonding were investigated. All tests were performed according to European code EN 300:2006. Results showed the influence of wood species on physical and mechanical properties. Panels made with higher density woods such as Cambará presented better physical performance, while those made with lower density woods such as Pinus presented better mechanical properties. Besides that, strand particle geometry was also influenced on all physical and mechanical properties investigated. Therefore, the feasibility of using alternative species and wood from first thinning and with castor oil-based polyurethane resin in OSB production was verified.

The environmental assessment of the wood combustion

International Nuclear Information System (INIS)

Dinca, Cristian; Badea, Adrian; Apostol, Tiberiu

2007-01-01

In this paper, the authors analysed the emissions from residential boilers burning wood logs, bark pellets, wood briquettes and wood pellets. Three boilers, selected with respect to age, design, connection to heat storage tank, and type of biofuel, were included in the study. The emissions captured comprised carbon monoxide (CO), carbon dioxide (CO 2 ), oxygen (O 2 ), total organic carbons (TOC), nitrogen oxides (NO x ), polycyclic aromatic hydrocarbons (PAC) and 33 volatile organic compounds (VOC). We have used the Life Cycle Inventory method in order to identify the main stressors generated by the wood combustion stage. In this purpose, we have analysed one type of old boiler, one type of modern boiler and a multi-fuel boiler, which can burn wood logs, bark pellets, wood briquettes and wood pellets. In this article, we selected only the wood combustion stage because it is the most important according to the emissions produced. (authors)

Wood-energy - The sector get worried

International Nuclear Information System (INIS)

Mary, Olivier; Signoret, Stephane; Bohlinger, Philippe; Guilhem, Jean; De Santis, Audrey; Sredojevic, Alexandre; Defaye, Serge; Maindrault, Marc

2017-01-01

Wood energy is, today and certainly also tomorrow, one of the most important renewable energies in France. However, the wood-energy sector seems to slow down as hydrocarbon prices stay extremely low. This document presents 8 articles, describing the context and the characteristics of this evolution, plus some examples of developments in France. The themes of the articles are: the activity of the wood-energy sector should be reinforced to meet the objectives of the French energy multi-year plan; The 2035 prospective of the wood yield in the French forest will meet the future demand, however this evaluation does not take into consideration the effects of the climatic change; the conversion to biomass of the 'Fort de l'Est' (near Paris) heating system (equipped with a boiling fluidized bed boiler) has enabled the heat network to beat the 50 pc share of renewable energy; wood-energy professionals use the 'quality' lever to challenge their fossil fuel competitors; the city of Orleans is now equipped with an innovative biomass cogeneration plant; the example of wood waste valorization in a French sawmill; the French ONF (Forest Administration) Wood-Energy actor has just inaugurated its largest biomass dryer, in order to develop the domestic market for wood as a fuel; analysis of the technical and economical feasibility of using wood to generate electric power or replacing electric space heating by heat network

Coal and wood fuel for electricity production: An environmentally sound solution for waste and demolition wood

Energy Technology Data Exchange (ETDEWEB)

Penninks, F.W.M. [EPON, Zwolle (Netherlands)

1997-12-31

Waste wood from primary wood processing and demolition presents both a problem and a potential. If disposed in landfills, it consumes large volumes and decays, producing CH{sub 4}, CO{sub 2} and other greenhouse gases. As an energy source used in a coal fired power plant it reduces the consumption of fossil fuels reducing the greenhouse effect significantly. Additional advantages are a reduction of the ash volume and the SO{sub 2} and NO{sub x} emissions. The waste wood requires collection, storage, processing and burning. This paper describes a unique project which is carried out in the Netherlands at EPON`s Gelderland Power Plant (635 MW{sub e}) where 60 000 tonnes of waste and demolition wood will be used annually. Special emphasis is given to the processing of the powdered wood fuel. Therefore, most waste and demolition wood can be converted from an environmental liability to an environmental and economic asset. (author)

Coal and wood fuel for electricity production: An environmentally sound solution for waste and demolition wood

Energy Technology Data Exchange (ETDEWEB)

Penninks, F W.M. [EPON, Zwolle (Netherlands)

1998-12-31

Waste wood from primary wood processing and demolition presents both a problem and a potential. If disposed in landfills, it consumes large volumes and decays, producing CH{sub 4}, CO{sub 2} and other greenhouse gases. As an energy source used in a coal fired power plant it reduces the consumption of fossil fuels reducing the greenhouse effect significantly. Additional advantages are a reduction of the ash volume and the SO{sub 2} and NO{sub x} emissions. The waste wood requires collection, storage, processing and burning. This paper describes a unique project which is carried out in the Netherlands at EPON`s Gelderland Power Plant (635 MW{sub e}) where 60 000 tonnes of waste and demolition wood will be used annually. Special emphasis is given to the processing of the powdered wood fuel. Therefore, most waste and demolition wood can be converted from an environmental liability to an environmental and economic asset. (author)

Mineralogy of Non-Silicified Fossil Wood

Directory of Open Access Journals (Sweden)

George E. Mustoe

2018-03-01

Full Text Available The best-known and most-studied petrified wood specimens are those that are mineralized with polymorphs of silica: opal-A, opal-C, chalcedony, and quartz. Less familiar are fossil woods preserved with non-silica minerals. This report reviews discoveries of woods mineralized with calcium carbonate, calcium phosphate, various iron and copper minerals, manganese oxide, fluorite, barite, natrolite, and smectite clay. Regardless of composition, the processes of mineralization involve the same factors: availability of dissolved elements, pH, Eh, and burial temperature. Permeability of the wood and anatomical features also plays important roles in determining mineralization. When precipitation occurs in several episodes, fossil wood may have complex mineralogy.

Recycling of wood products. Final report of the preliminary study project partly financed by the Finnish Wood Research Oy; Puutuotteiden kierraetys. Finnish Wood Research Oy:n osarahoittaman esiselvityshankkeen loppuraportti

Energy Technology Data Exchange (ETDEWEB)

Pirhonen, I.; Heraejaervi, H.; Saukkola, P.; Raety, T.; Verkasalo, E., Email: henrik.herajarvi@metla.fi

2011-07-01

The objective of this preliminary study was to clarify the present state of recycling of wood in Finland and Europe. In the work the control measures of recycling were examined. In Finland there will be a total amount of 850 000 tons of waste wood per year. Of this amount 670 000 tons is from construction and demolishing of buildings. Burning the wood to energy is technically and economically the most reasonable use of waste wood in Finland and in several other European countries where there is a long heating season. A lot of work has been done to find new ways of utilization. The objective of the European Union to increase the use of renewable natural resources in the energy production creates an additional demand to all kinds of wood, including waste wood. The waste legislation of Finland and EU is directing to recycling, not restricting it. Furthermore, the systems to try to create markets for products containing recycled materials are under development. In the future it is expected that the legislation is tightening and the burning of waste wood is no longer calculated as acceptable recycling. Other ways to utilize wood waste should then already be developed. Furthermore, the development and introduction of new recycling methods are of important significance also when marketing wood and wood products. The recycling should be taken into consideration already at the planning stage of the building

Surface characterization of weathered wood-plastic composites produced from modified wood flour

Science.gov (United States)

James S. Fabiyi; Armando G. McDonald; Nicole M. Stark

2007-01-01

The effects of weathering on the surface properties of wood-plastic composites (WPC) were examined. High-density polyethylene (HDPE) based WPCs made from modified wood flour (untreated, extractives free, and holocellulose (delignified) fibers) were subjected to accelerated (xenon-arc) weathering. Colorimetry and Fourier-transform infrared spectroscopy were employed to...

Discover the benefits of residential wood heating

International Nuclear Information System (INIS)

2003-01-01

This publication described how residential wood-heating systems are being used to reduce energy costs and increase home comfort. Biomass energy refers to all forms are renewable energy that is derived from plant materials. The source of fuel may include sawmills, woodworking shops, forest operations and farms. The combustion of biomass is also considered to be carbon dioxide neutral, and is not considered to be a major producer of greenhouse gases (GHG) linked to global climate change. Wood burning does, however, release air pollutants, particularly if they are incompletely burned. Incomplete combustion of wood results in dense smoke consisting of toxic gases. Natural Resources Canada helped create new safety standards and the development of the Wood Energy Technical Training Program to ensure that all types of wood-burning appliances are installed correctly and safely to reduce the risk of fire and for effective wood heating. In Canada, more than 3 million families heat with wood as a primary or secondary heating source in homes and cottages. Wood heating offers security from energy price fluctuations and electrical power failures. This paper described the benefits of fireplace inserts that can transform old fireplaces into modern heating systems. It also demonstrated how an add-on wood furnace can be installed next to oil furnaces to convert an oil-only heating system to a wood-oil combination system, thereby saving thousands of dollars in heating costs. Wood pellet stoves are another wood burning option. The fuel for the stoves is produced from dried, finely ground wood waste that is compressed into hard pellets that are loaded into a hopper. The stove can run automatically for up to 24 hours. New high-efficiency advanced fireplaces also offer an alternative heating system that can reduce heating costs while preserving Canada's limited supply of fossil fuels such as oil and gas. 13 figs

Quantifying arthropod contributions to wood decay

Science.gov (United States)

Michael Ulyshen; Terry Wagner

2013-01-01

Termites carry large amounts of soil into dead wood, and this behaviour complicates efforts to measure their contributions to wood decay. A novel method for isolating termite soil by burning the wood is described, and some preliminary results are presented.

Chapter 6: Above Ground Deterioration of Wood and Wood-Based Materials

Science.gov (United States)

Grant Kirker; Jerrold Winandy

2014-01-01

Wood as a material has unique properties that make it ideal for above ground exposure in a wide range of structural and non-strucutral applications. However, no material is without limitations. Wood is a bio-polymer which is subject to degradative processes, both abiotic and biotic. This chapter is a general summary of the abiotic and biotic factors that impact service...

X-ray initiated polymerization of wood impregnants

Energy Technology Data Exchange (ETDEWEB)

Cleland, Marshall R.; Galloway, Richard A. [IBA Industrial, Inc., Edgewood, NY (United States); Berejka, Anthony J. [Ionicorp, Huntington, NY 11743 (United States)], E-mail: berejka@msn.com; Montoney, Daniel [Strathmore Products, Syracuse, NY (United States); Driscoll, Mark; Smith, Leonard; Scott Larsen, L. [State University of New York, SUNY-ESF, Syracuse, NY (United States)

2009-07-15

X-rays, derived from a high energy, high-current electron beam (EB), initiated in-situ polymerization of a unique class of monomers that were found to penetrate the cell walls of wood. X-rays initiated an auto-catalytic acrylic polymerization and penetrated through thick pieces of wood. The final cured product having the polymerizate, a polymer, both in the wood cell lumens and in the cell walls is called wood impregnated with a wood-polymer penetrant (WPP). The controlled lower dose rate of X-rays overcame disproportionation encountered when using higher dose-rate electron beam initiation. With X-rays, the in-situ polymerization took place in one exposure of modest dose. With EB, multiple passes were needed to avoid excessive heat build-up and monomer volatilization. Having entered the cell walls of the wood and then being polymerized within the cell walls, these radiation-cured unique monomers imparted outstanding dimensional stability upon exposure of the impregnated wood to humidity cycling. The preferred monomer system was also chemically modified prior to impregnation with agents that would remain in the wood and prevent the growth of fungi and other microbials. This technique differs from historic uses of monomers that merely filled the lumens of the wood (historic wood-polymer composites), which are only suitable for indoor use. The WPP impregnated wood that was either X-ray cured or EB cured demonstrated enhanced structural properties, dimensional stability, and decay resistance.

X-ray initiated polymerization of wood impregnants

International Nuclear Information System (INIS)

Cleland, Marshall R.; Galloway, Richard A.; Berejka, Anthony J.; Montoney, Daniel; Driscoll, Mark; Smith, Leonard; Scott Larsen, L.

2009-01-01

X-rays, derived from a high energy, high-current electron beam (EB), initiated in-situ polymerization of a unique class of monomers that were found to penetrate the cell walls of wood. X-rays initiated an auto-catalytic acrylic polymerization and penetrated through thick pieces of wood. The final cured product having the polymerizate, a polymer, both in the wood cell lumens and in the cell walls is called wood impregnated with a wood-polymer penetrant (WPP). The controlled lower dose rate of X-rays overcame disproportionation encountered when using higher dose-rate electron beam initiation. With X-rays, the in-situ polymerization took place in one exposure of modest dose. With EB, multiple passes were needed to avoid excessive heat build-up and monomer volatilization. Having entered the cell walls of the wood and then being polymerized within the cell walls, these radiation-cured unique monomers imparted outstanding dimensional stability upon exposure of the impregnated wood to humidity cycling. The preferred monomer system was also chemically modified prior to impregnation with agents that would remain in the wood and prevent the growth of fungi and other microbials. This technique differs from historic uses of monomers that merely filled the lumens of the wood (historic wood-polymer composites), which are only suitable for indoor use. The WPP impregnated wood that was either X-ray cured or EB cured demonstrated enhanced structural properties, dimensional stability, and decay resistance.

On Erdos–Wood's conjecture

Indian Academy of Sciences (India)

In this article, we prove that infinite number of integers satsify Erdős–Woods conjecture. Moreover, it follows that the number of natural numbers ≤ satisfies Erdős–Woods conjecture with = 2 is at least /(log ) for some positive constant > 2.

The relationships of wood-, gas-, and water fractions of tree stems to performance and life history variation in tropical trees

NARCIS (Netherlands)

Poorter, L.

2008-01-01

Background and Aims: The volume of tree stems is made up of three components: solid wood, gas and water. These components have important consequences for the construction costs, strength and stability of trees. Here, the importance of stem components for sapling growth and survival in the field was

The economic potential of wood pellet production from alternative, low-value wood sources in the southeast of the US

NARCIS (Netherlands)

Hoefnagels, Ric; Junginger, Martin; Faaij, Andre

2014-01-01

The global demand for wood pellets used for energy purposes is growing. Therefore, increased amounts of wood pellets are produced from primary forestry products, such as pulp wood. The present analysis demonstrates that substantial amounts of alternative, low-value wood resources are available that

Users guide for WoodCite, a product cost quotation tool for wood component manufacturers [computer program

Science.gov (United States)

Jeff Palmer; Adrienn Andersch; Jan Wiedenbeck; Urs. Buehlmann

2014-01-01

WoodCite is a Microsoft® Access-based application that allows wood component manufacturers to develop product price quotations for their current and potential customers. The application was developed by the U.S. Forest Service and Virginia Polytechnic Institute and State University, in cooperation with the Wood Components Manufacturers Association.

Wood energy x 2 - Scenario for the development of wood energy use in Switzerland

International Nuclear Information System (INIS)

2004-01-01

This study for the Swiss Agency for the Environment, Forests and Landscapes (SAEFL) and the Swiss wood-energy association (Holzenergie Schweiz) presents the results of a scenario-study that examined if, and under what conditions, doubling the use of wood energy in Switzerland could help reach carbon dioxide reduction targets. Two scenarios are presented that are based on high and low rates of growth for the number of automatic wood-chipping or pellets-fired installations. For both scenarios, figures are presented on the amount of wood used and the heating energy generated. The political and financial prerequisites for the scenarios are discussed and other boundary conditions are defined. The report draws conclusions from the study of the two scenarios and summarises the political action deemed necessary

Implementation of new technologies in wood industry and their effect in wood products quality

OpenAIRE

ELVA ÇAUSHI; PANDELI MARKU

2014-01-01

There are about 300 companies producing furniture and about 250 small and medium enterprises (SME) producing sawn timber, which operate in the field of wood industry in Albania. This wood industry production is being challenged by the increasing demand in the domestic market, ranging from kitchen furniture to office and schools furniture, bedroom furniture, doors, windows, and saw timber in different dimensions. The production from the wood industry can fulfill about 80% of the domestic mark...

Refraction and absorption of microwaves in wood

International Nuclear Information System (INIS)

Ziherl, Saša; Bajc, Jurij; Čepič, Mojca

2013-01-01

A demonstration experiment for physics students showing the dependence of the refractive index and absorption coefficient of wood on the direction of microwaves is presented. Wood and microwaves enable study of anisotropic properties, which are typically found in crystals. Wood is used as the persuasive representative of uniaxial anisotropic materials due to its visible structure and its consequent anisotropic properties. Wood can be cut in a general direction and wooden plates a few centimetres thick with well-defined fibre orientation are easily prepared. Microwaves are used because wood is transparent for microwaves and their centimetre-scale wavelength is comparable to the wood structure. (paper)

Wood for fuel

Energy Technology Data Exchange (ETDEWEB)

Beaton, D

1986-01-01

Growing wood for energy could contribute three million tonnes of coal equivalent per year by the end of the century. Research programmes in the UK involved with energy forestry are reported. Three systems of wood energy, modified conventional forestry, single stem timber cropping and short rotation coppicing are being investigated. The short rotation coppicing requires inputs similar to those of agricultural crops and the machinery geared towards agricultural operations is compatible with it. Single stem forestry has a medium rotation period of 20 years. The production of coppice wood fuels is discussed in further detail for different parts of the UK with recommendations for species selection and adaption of existing farming practices. A coppice willow harvester has been developed for harvesting during November - February. Weed control and fertilizer application are also briefly mentioned.

The Swedish wood fuel market

International Nuclear Information System (INIS)

Hillring, Bengt

1999-01-01

In Sweden, wood fuels are traditionally used in the Swedish forest products industry and for heating of single-family houses. More recently they are also become established as an energy source for district heating and electricity production. Energy policy, especially the energy taxation system, has favoured wood fuels and other biofuels, mainly for environmental reasons. There is now an established commercial market for wood fuels in the district heating sector, which amounts to 45 PJ and is growing 20 per cent annually. Price levels have been stable in current prices for a decade, mainly because of good access to wood fuels. Price levels are dominated by production costs on a market that is largely governed by the buyer. It is expected that the use of wood fuels will increased in Sweden in the future, which will push a further development of this section on the market and bring about technological changes in the area. (Author)

Fatigue Damage in Wood

DEFF Research Database (Denmark)

Clorius, Christian Odin; Pedersen, Martin Bo Uhre; Hoffmeyer, Preben

1996-01-01

An investigation of fatigue failure in wood subjected to load cycles in compression parallel to grain is presented. Fatigue failure is found to depend both on the total time under load and on the number of cycles.Recent accelerated fatigue research on wood is reviewed, and a discrepancy between...... to 10 Hz are used. The number of cycles to failure is found to be a poor measure of the fatigue performance of wood. Creep, maximum strain, stiffness and work are monitored throughout the fatigue tests. Accumulated creep is suggested identified with damage and a correlation between stiffness reduction...

Wood and Sediment Dynamics in River Corridors

Science.gov (United States)

Wohl, E.; Scott, D.

2015-12-01

Large wood along rivers influences entrainment, transport, and storage of mineral sediment and particulate organic matter. We review how wood alters sediment dynamics and explore patterns among volumes of instream wood, sediment storage, and residual pools for dispersed pieces of wood, logjams, and beaver dams. We hypothesized that: volume of sediment per unit area of channel stored in association with wood is inversely proportional to drainage area; the form of sediment storage changes downstream; sediment storage correlates most strongly with wood load; and volume of sediment stored behind beaver dams correlates with pond area. Lack of data from larger drainage areas limits tests of these hypotheses, but analyses suggest a negative correlation between sediment volume and drainage area and a positive correlation between wood and sediment volume. The form of sediment storage in relation to wood changes downstream, with wedges of sediment upstream from jammed steps most prevalent in small, steep channels and more dispersed sediment storage in lower gradient channels. Use of a published relation between sediment volume, channel width, and gradient predicted about half of the variation in sediment stored upstream from jammed steps. Sediment volume correlates well with beaver pond area. Historically more abundant instream wood and beaver populations likely equated to greater sediment storage within river corridors. This review of the existing literature on wood and sediment dynamics highlights the lack of studies on larger rivers.

Management alternatives of energy wood thinning stands

International Nuclear Information System (INIS)

Heikkilae, Jani; Siren, Matti; Aeijaelae, Olli

2007-01-01

Energy wood thinning has become a feasible treatment alternative of young stands in Finland. Energy wood thinnings have been carried out mainly in stands where precommercial thinning has been neglected and the harvesting conditions for industrial wood thinning are difficult. Despite of its positive effects on harvesting costs and on renewable energy potential, whole-tree harvesting has been constantly criticized for causing growth loss. In this paper, the profitability of energy wood thinning was studied in 20 Scots pine-dominated stands where energy wood thinning was carried out. The growth of the stands after thinning was predicted with the help of Motti-stand simulator. Entire rotation time of the stands was simulated with different management alternatives. The intensity of first thinning and recovery level of logging residues varied between alternatives. In order to attain acceptable harvesting conditions, industrial wood thinning had to be delayed. The effect of energy wood thinning on subsequent stem wood growth was almost the same as in conventional thinning. Whole-tree harvesting for energy proved to be profitable alternative if the stumpage price is around 3EUR m -3 , the interest rate is 3% or 5% and the removal of pulpwood is less than 20 m 3 ha -1 . If the harvestable pulpwood yield is over 20 m 3 ha -1 , integrated harvesting of industrial and energy wood or delayed industrial wood harvesting becomes more profitable. (author)

Decay extent evaluation of wood degraded by a fungal community using NIRS: application for ecological engineering structures used for natural hazard mitigation

Science.gov (United States)

Baptiste Barré, Jean; Bourrier, Franck; Bertrand, David; Rey, Freddy

2015-04-01

Ecological engineering corresponds to the design of efficient solutions for protection against natural hazards such as shallow landslides and soil erosion. In particular, bioengineering structures can be composed of a living part, made of plants, cuttings or seeds, and an inert part, a timber logs structure. As wood is not treated by preservatives, fungal degradation can occur from the start of the construction. It results in wood strength loss, which practitioners try to evaluate with non-destructive tools (NDT). Classical NDT are mainly based on density measurements. However, the fungal activity reduces the mechanical properties (modulus of elasticity - MOE) well before well before a density change could be measured. In this context, it would be useful to provide a tool for assessing the residual mechanical strength at different decay stages due to a fungal community. Near-infrared spectroscopy (NIRS) can be used for that purpose, as it can allow evaluating wood mechanical properties as well as wood chemical changes due to brown and white rots. We monitored 160 silver fir samples (30x30x6000mm) from green state to different levels of decay. The degradation process took place in a greenhouse and samples were inoculated with silver fir decayed debris in order to accelerate the process. For each sample, we calculated the normalized bending modulus of elasticity loss (Dw moe) and defined it as decay extent. Near infrared spectra collected from both green and decayed ground samples were corrected by the subtraction of baseline offset. Spectra of green samples were averaged into one mean spectrum and decayed spectra were subtracted from the mean spectrum to calculate the absorption loss. Partial least square regression (PLSR) has been performed between the normalized MOE loss Dw moe (0 wood decay extent in the context of ecological engineering structures used for natural hazard mitigation.

Impregnating Systems for Producing Wood-Plastic Composite Materials and Resinified Woods by Radiochemical Means

International Nuclear Information System (INIS)

Laizier, J.; Laroche, R.; Marchand, J.

1969-01-01

The effect of the nature of the components in the impregnation mixture on the characteristics of wood-plastic combinations has been studied in the case of beech by applying a wide variety of compositions. In particular, the effect of water (in the impregnator, and in the form of moisture in the wood) on the characteristics of the products obtained has been determined. It has been shown that, in place of the conventional method for preparing resinified woods (using a ternary monomer-solvent-water mixture), it is possible to use a method involving comonomers, which obviate the need to dry the wood after treatment. The evaluation of the results obtained is based on the value of the impregnation rate and on the modifications in microscopic structure; these emphasize the differences between the types of filler and enable comparisons to be drawn with the dimensional stabilities observed. Measurements of variations in dimensions and the recurrence of moisture have made it possible to establish a classification based on the types of monomer used and the operating conditions. It is shown that a whole range of products is obtained, the properties of which differ widely and are comparatively easily adaptable to the purpose specified. These properties illustrate clearly the differences and characteristics of resinified woods as opposed to conventional wood-plastic materials. (author) [fr

NorWood: a gene expression resource for evo-devo studies of conifer wood development.

Science.gov (United States)

Jokipii-Lukkari, Soile; Sundell, David; Nilsson, Ove; Hvidsten, Torgeir R; Street, Nathaniel R; Tuominen, Hannele

2017-10-01

The secondary xylem of conifers is composed mainly of tracheids that differ anatomically and chemically from angiosperm xylem cells. There is currently no high-spatial-resolution data available profiling gene expression during wood formation for any coniferous species, which limits insight into tracheid development. RNA-sequencing data from replicated, high-spatial-resolution section series throughout the cambial and woody tissues of Picea abies were used to generate the NorWood.conGenIE.org web resource, which facilitates exploration of the associated gene expression profiles and co-expression networks. Integration within PlantGenIE.org enabled a comparative regulomics analysis, revealing divergent co-expression networks between P. abies and the two angiosperm species Arabidopsis thaliana and Populus tremula for the secondary cell wall (SCW) master regulator NAC Class IIB transcription factors. The SCW cellulose synthase genes (CesAs) were located in the neighbourhoods of the NAC factors in A. thaliana and P. tremula, but not in P. abies. The NorWood co-expression network enabled identification of potential SCW CesA regulators in P. abies. The NorWood web resource represents a powerful community tool for generating evo-devo insights into the divergence of wood formation between angiosperms and gymnosperms and for advancing understanding of the regulation of wood development in P. abies. © 2017 The Authors. New Phytologist © 2017 New Phytologist Trust.

Manufacturing methods and magnetic characteristics of magnetic wood

International Nuclear Information System (INIS)

Oka, H.; Hojo, A.; Osada, H.; Namizaki, Y.; Taniuchi, H.

2004-01-01

The relationship between wood construction and DC magnetic characteristics for three types of magnetic wood was experimentally investigated. The results show that the magnetic characteristics of each type of magnetic wood are dependent on the magnetic materials, the density of the magnetic material and the construction of the wood. Furthermore, it was determined that the relationship between the fiber direction and the magnetic path direction of the magnetic wood influenced the wood's magnetic characteristics

PHYSICAL AND MECHANICAL PROPERTIES OF Araucaria angustifolia (Bertol. WOOD FOR THREE STRATUM PHYTOSOCIOLOGICAL

Directory of Open Access Journals (Sweden)

Rafael Beltrame

2010-11-01

Full Text Available The study of physical and mechanical properties of wood is essential for industrial use both in construction and the manufacture of furniture. Thus, the study aimed to determine the physical and mechanical properties of the Araucaria angustifolia wood in terms of three strata phytosociological. For this, 15 trees were felled, five belonging to the upper stratum, the middle stratum five and five for the lower strata. The trees were deployed for the preparation of specimens used for mechanical testing. In the mechanical characterization of the species assays were performed for impact resistance, static bending, compression axial and perpendicular to the fibers. As for the characterization of physical properties, determined the apparent specific gravity at 12% relative humidity for each extract. The results did not show significant differences in the tests of impact resistance and static bending to the strata phytosociological. As for the apparent specific gravity, compression axial and perpendicular there was a change in the values of propertiesbetween the strata phytosociological, is generally butter in the middle and upper strata. Therefore the physical and mechanical properties tend to present higher values these two strata. The data analysis allowed of Araucaria angustifolia wood has moderate mechanical strength when compared with other species studies.

Assessment and management of dead-wood habitat

Science.gov (United States)

Hagar, Joan

2007-01-01

The Bureau of Land Management (BLM) is in the process of revising its resource management plans for six districts in western and southern Oregon as the result of the settlement of a lawsuit brought by the American Forest Resource Council. A range of management alternatives is being considered and evaluated including at least one that will minimize reserves on O&C lands. In order to develop the bases for evaluating management alternatives, the agency needs to derive a reasonable range of objectives for key issues and resources. Dead-wood habitat for wildlife has been identified as a key resource for which decision-making tools and techniques need to be refined and clarified. Under the Northwest Forest Plan, reserves were to play an important role in providing habitat for species associated with dead wood (U.S. Department of Agriculture Forest Service and U.S. Department of the Interior Bureau of Land Management, 1994). Thus, the BLM needs to: 1) address the question of how dead wood will be provided if reserves are not included as a management strategy in the revised Resource Management Plan, and 2) be able to evaluate the effects of alternative land management approaches. Dead wood has become an increasingly important conservation issue in managed forests, as awareness of its function in providing wildlife habitat and in basic ecological processes has dramatically increased over the last several decades (Laudenslayer et al., 2002). A major concern of forest managers is providing dead wood habitat for terrestrial wildlife. Wildlife in Pacific Northwest forests have evolved with disturbances that create large amounts of dead wood; so, it is not surprising that many species are closely associated with standing (snags) or down, dead wood. In general, the occurrence or abundance of one-quarter to one-third of forest-dwelling vertebrate wildlife species, is strongly associated with availability of suitable dead-wood habitat (Bunnell et al., 1999; Rose et al., 2001). In

Radiation processing of wood-plastic composites

International Nuclear Information System (INIS)

Czvikovszky, T.

1992-01-01

There are three main types of radiation-processed composite material derived from plastics and fibrous natural polymers. The first are the monomer-impregnated, radiation-treated wood-plastic composites (WPC). They became a commercial success in the early 1970s. More recently, work has focused on improving the WPCs by creating in them interpenetrating network (IPN) systems by the use of appropriate multifunctional oligomers and monomers. The main kinetic features of radiation-initiated chain polymerization remain applicable even in impregnated wood. The second type are the plastics filled or reinforced with dispersed wood fiber or other cellulosics (WFRP). In their case, radiation processing offers a new opportunity to apply radiation-reactive adhesion promoters between wood or cellulosic fibers and the thermoplastic matrices. The third type are the laminar composites made by electron beam coating of wood-based agglomerate sheets and boards. This chapter reviews the industrial applications and the radiation processing of the three types of the wood-plastic composites and indicates future trends. (orig.)

Simulated long-term effects of varying tree retention on wood production, dead wood and carbon stock changes.

Science.gov (United States)

Santaniello, Francesca; Djupström, Line B; Ranius, Thomas; Weslien, Jan; Rudolphi, Jörgen; Sonesson, Johan

2017-10-01

Boreal forests are an important source of timber and pulp wood, but provide also other products and services. Utilizing a simulation program and field data from a tree retention experiment in a Scots pine forest in central Sweden, we simulated the consequences during the following 100 years of various levels of retention on production of merchantable wood, dead wood input (as a proxy for biodiversity), and carbon stock changes. At the stand level, wood production decreased with increased retention levels, while dead wood input and carbon stock increased. We also compared 12 scenarios representing a land sharing/land sparing gradient. In each scenario, a constant volume of wood was harvested with a specific level of retention in a 100-ha landscape. The area not needed to reach the defined volume was set-aside during a 100-year rotation period, leading to decreasing area of set-asides with increasing level of retention across the 12 scenarios. Dead wood input was positively affected by the level of tree retention whereas the average carbon stock decreased slightly with increasing level of tree retention. The scenarios will probably vary in how they favor species preferring different substrates. Therefore, we conclude that a larger variation of landscape-level conservation strategies, also including active creation of dead wood, may be an attractive complement to the existing management. Copyright © 2017 Elsevier Ltd. All rights reserved.

Wood-plastic composites as promising green-composites for automotive industries!

Science.gov (United States)

Ashori, Alireza

2008-07-01

Wood-plastic composite (WPC) is a very promising and sustainable green material to achieve durability without using toxic chemicals. The term WPCs refers to any composites that contain plant fiber and thermosets or thermoplastics. In comparison to other fibrous materials, plant fibers are in general suitable to reinforce plastics due to relative high strength and stiffness, low cost, low density, low CO2 emission, biodegradability and annually renewable. Plant fibers as fillers and reinforcements for polymers are currently the fastest-growing type of polymer additives. Since automakers are aiming to make every part either recyclable or biodegradable, there still seems to be some scope for green-composites based on biodegradable polymers and plant fibers. From a technical point of view, these bio-based composites will enhance mechanical strength and acoustic performance, reduce material weight and fuel consumption, lower production cost, improve passenger safety and shatterproof performance under extreme temperature changes, and improve biodegradability for the auto interior parts.

Application of Meta-Heuristic Hybrid Artificial Intelligence Techniques for Modeling of Bonding Strength of Plywood Panels

Directory of Open Access Journals (Sweden)

Cenk Demirkır

2014-04-01

Full Text Available Plywood, which is one of the most important wood based panels, has many usage areas changing from traffic signs to building constructions in many countries. It is known that the high quality plywood panel manufacturing has been achieved with a good bonding under the optimum pressure conditions depending on adhesive type. This is a study of determining the using possibilities of modern meta-heuristic hybrid artificial intelligence techniques such as IKE and AANN methods for prediction of bonding strength of plywood panels. This study has composed of two main parts as experimental and analytical. Scots pine, maritime pine and European black pine logs were used as wood species. The pine veneers peeled at 32°C and 50°C were dried at 110°C, 140°C and 160°C temperatures. Phenol formaldehyde and melamine urea formaldehyde resins were used as adhesive types. EN 314-1 standard was used to determine the bonding shear strength values of plywood panels in experimental part of this study. Then the intuitive k-nearest neighbor estimator (IKE and adaptive artificial neural network (AANN were used to estimate bonding strength of plywood panels. The best estimation performance was obtained from MA metric for k-value=10. The most effective factor on bonding strength was determined as adhesive type. Error rates were determined less than 5% for both of the IKE and AANN. It may be recommended that proposed methods could be used in applying to estimation of bonding strength values of plywood panels.

Substitution potentials of recycled HDPE and wood particles from post-consumer packaging waste in Wood-Plastic Composites.

Science.gov (United States)

Sommerhuber, Philipp F; Welling, Johannes; Krause, Andreas

2015-12-01

The market share of Wood-Plastic Composites (WPC) is small but expected to grow sharply in Europe. This raises some concerns about suitable wood particles needed in the wood-based panels industry in Europe. Concerns are stimulated by the competition between the promotion of wooden products through the European Bioeconomy Strategy and wood as an energy carrier through the Renewable Energy Directive. Cascade use of resources and valorisation of waste are potential strategies to overcome resource scarcity. Under experimental design conditions, WPC made from post-consumer recycled wood and plastic (HDPE) were compared to WPC made from virgin resources. Wood content in the polymer matrix was raised in two steps from 0% to 30% and 60%. Mechanical and physical properties and colour differences were characterized. The feasibility of using cascaded resources for WPC is discussed. Results indicate the technical and economic feasibility of using recycled HDPE from packaging waste for WPC. Based on technical properties, 30% recycled wood content for WPC is feasible, but economic and political barriers of efficient cascading of biomass need to be overcome. Copyright © 2015 Elsevier Ltd. All rights reserved.

Mechanical Behaviour of the Wood Masonry

Directory of Open Access Journals (Sweden)

Fazia FOUCHAL

2011-09-01

Full Text Available In this paper we study the walls wood masonry behaviour. First, we propose a regulatory validation of the walls wood masonry behaviour subjected to vertical and horizontal loads according to Eurocode 5. Then we present the numerical application on the wall wood supported two floors level.

Use of nanofillers in wood coatings

DEFF Research Database (Denmark)

Nikolic, Miroslav; Lawther, John Mark; Sanadi, Anand Ramesh

2015-01-01

Wood has been used for thousands of years and remains an important material in the construction industry, most often protected with coatings. Development of nanotechnology allows further improvements or new performance properties to be achieved in wood coatings. Increased UV protection...... with nanometal oxides that allow wood texture to remain seen and higher resilience to scratch and abrasion with use of different nanoparticle shapes are some of the applications that are reviewed here. A variety of possible applications together with a high level of improvements, alongside commercial factors...... like a low level of loading, have already established nanoparticles in some areas of wood coatings. This article is a comprehensive scientific review of the published work in the use of nanofillers in wood coatings....

Moisture relations and physical properties of wood

Science.gov (United States)

Samuel V. Glass; Samuel L. Zelinka

2010-01-01

Wood, like many natural materials, is hygroscopic; it takes on moisture from the surrounding environment. Moisture exchange between wood and air depends on the relative humidity and temperature of the air and the current amount of water in the wood. This moisture relationship has an important influence on wood properties and performance. Many of the challenges of using...

Adhesives for Achieving Durable Bonds with Acetylated Wood

Science.gov (United States)

Charles Frihart; Rishawn Brandon; James Beecher; Rebecca Ibach

2017-01-01

Acetylation of wood imparts moisture durability, decay resistance, and dimensional stability to wood; however, making durable adhesive bonds with acetylated wood can be more difficult than with unmodified wood. The usual explanation is that the acetylated surface has fewer hydroxyl groups, resulting in a harder-to-wet surface and in fewer hydrogen bonds between wood...

Comparative study on liquefaction of creosote and chromated copper arsenate (CCA)-treated wood and untreated southern pine wood: effects of acid catalyst content, liquefaction time, temperature, and phenol to wood ratio

Science.gov (United States)

Hui Pan; Chung-Yun Hse; Todd F. Shupe

2009-01-01

Creosote- and chromated copper arsenate (CCA)-treated wood waste and untreated southern pine wood were liquefied with phenol and sulfuric acid. The effects of sulfuric acid content, liquefaction time, liquefaction temperature, and phenol to wood ratio on liquefaction rate (i.e., wood residue content) were investigated and analyzed by analysis of variance (...

Method of stabilizing wood

International Nuclear Information System (INIS)

Pesek, M.; Jarkovsky, J.

1973-01-01

Wood is impregnated with a mixture of a vinyl or an allyl monomer (20 - 90 wt. %) and unsaturated polyester resins. The impregnated wood is then exposed to ionizing radiation at doses of 0.1 to 20 Mrad at a temperature of 60 to 180 degC. (B.S.)

Switzerland's largest wood-pellet factory in Balsthal

International Nuclear Information System (INIS)

Stohler, F.

2004-01-01

This article describes how a small Swiss electricity utility has broken out of its traditional role in power generation and the distribution of electricity and gone into the production of wood pellets. The pellets, which are made from waste wood (sawdust) available from wood processing companies, are produced on a large scale in one of Europe's largest pellets production facilities. The boom in the use of wood pellets for heating purposes is discussed. The article discusses this unusual approach for a Swiss power utility, which also operates a wood-fired power station and is even involved in an incineration plant for household wastes. The markets being aimed for in Switzerland and in Europe are described, including modern low-energy-consumption housing projects. A further project is described that is to use waste wood available from a large wood processing facility planned in the utility's own region

Preparation and applications of wood-polyester composites

International Nuclear Information System (INIS)

Czvikovszky, T.

1982-01-01

Optimum processing parameters were searched for the pilot-scale production of wood-polyester composites by irradiation of resin-impregnated wood material. The radiation initiation of the following systems were examined in wood and without wood matrix: methyl methacrylate, mixture of styrene and acrylonitryle, and their combination with unsaturated polyester. In the most cases the over-all rate of the complete polymerization process in wood matrix is proportional to the square root of the initiation rate. The parameters of the radiation technology of wood-polyester composites have been determined, using 260 TBq (7 kCi) 60 Co radiation source. A pilot plant has been constructed using an underwater irradiation system of 1.85 PBq (50 kCi) 60 Co. The successful production rate of 200 kg wood-polyester composite per day, as well as the application tests have demonstrated the technical feasibility of this new structural material. (author)

RESISTANCE TO THE ATTACK OF DRY-WOOD TERMITES (Cryptotermes brevis) OF SIX WOOD SPECIES

OpenAIRE

Fabrício Gomes Gonçalves; José Tarcísio da Silva Oliveira

2006-01-01

The dry wood termites are one of the largest causes of damages in wood used in Brazil. This work analyzed the attackof the Cryptotermes brevis in six commercials wood species in the north of the Rio de Janeiro and south of the Espírito Santo. The testobserved the number of holes, the percentage of died individuals and the damage of the pieces. When compared to the Pinus sp(reference), the species with less susceptibility to the attack were Cedrela fissilis, Cariocar brasiliense and Goupia gla...

Chapter 02: Basic wood biology—Anatomy for identification

Science.gov (United States)

Alex Wiedenhoeft

2011-01-01

Before the topics of using a hand lens, preparing wood for observation, and understanding the characters used in wood identification can be tackled, a general introduction to the biology of wood must be undertaken. The woods in commercial trade in Central America come almost exclusively from trees, so the discussion of wood biology is restricted to trees here, though...

Wood for sound.

Science.gov (United States)

Wegst, Ulrike G K

2006-10-01

The unique mechanical and acoustical properties of wood and its aesthetic appeal still make it the material of choice for musical instruments and the interior of concert halls. Worldwide, several hundred wood species are available for making wind, string, or percussion instruments. Over generations, first by trial and error and more recently by scientific approach, the most appropriate species were found for each instrument and application. Using material property charts on which acoustic properties such as the speed of sound, the characteristic impedance, the sound radiation coefficient, and the loss coefficient are plotted against one another for woods. We analyze and explain why spruce is the preferred choice for soundboards, why tropical species are favored for xylophone bars and woodwind instruments, why violinists still prefer pernambuco over other species as a bow material, and why hornbeam and birch are used in piano actions.

Moisture measurement in wood, wood-based materials and building materials - a literature review

International Nuclear Information System (INIS)

Kober, A.; Mehlhorn, L.; Plinke, B.

1989-10-01

Methods of moisture measurement in solid substances, especially on wood, wood-based materials and building materials were examined and evaluated according to the literature available. The question was which methods of examining the moisture distribution in building elements at climate loading offer the best accuracy and spatial resolution as well as which methods are the most appropriate at present and in future for the solution of measurement problems in the wood and wood-based industry. The most common methods are electric measurement methods which are utilizing either the moisture-depending conductivity or the dielectric constant or the reflectivity of the material for infrared radiation but they offer only a limited accuracy. The same is valid for the rarely used microwave methods or X-ray and NMR tomography. Simple electric methods will further on play an important role in the industrial process measuring technique. For the examination of building elements, methods using nuclear radiation still offer possibilities for a further development. (orig.) With 207 refs., 13 figs [de

Nuclear Car Wash sensitivity in varying thicknesses of wood and steel cargo

International Nuclear Information System (INIS)

Church, J; Slaughter, D; Asztalos, S; Biltoft, P; Descalle, M; Hall, J; Manatt, D; Mauger, J; Norman, E; Petersen, D; Prussin, S

2006-01-01

The influence of incident neutron attenuation on signal strengths in the Nuclear Car Wash has been observed experimentally for both wood and steel-pipe mock cargos. Measured decay curves are presented for β-delayed high-energy γ-rays and thermalized neutrons following neutron-induced fission of HEU through varying irradiation lengths. Error rates are extracted for delayed-γ and delayed-n signals integrated to 30 seconds, assuming Gaussian distributions for the active background. The extrapolation to a field system of 1 mA deuterium current and to a 5 kg sample size is discussed

Rural Fuel-wood and Poles Research Project in Malawi: a general account

Energy Technology Data Exchange (ETDEWEB)

Nkaonja, R S.W.

1981-01-01

The Rural Fuel-wood and Poles Research Project was initiated to provide information about afforestation in the dry silvicultural zones. Plantation forestry in Malawi has concentrated on production of timber, poles, and pulpwood. It is estimated that 90% of Malawi's population of 5.5 million live in rural communities, and that the purely domestic wood requirement is 4.05 cubic m per family (of five) annually. In addition, wood is required for agricultural purposes such as tobacco curing. The remaining indigenous forest cannot meet the demand. There is an urgent need for plantations. Rather than simply planting trees, the aim is to make local communities self-sufficient in forest products. In view of the shortage of land, great emphasis is placed on trying species which have many end-uses-- e.g., poles, fuel-wood, mulch, fodder, and shade--and those which can be grown together with farm crops, a concept known as ''agroforestry.'' Over 20 ha of trials were established at locations in the three regions of the country. Acacia albida allows maize and other farm crops to grow under it, provides good shade and fodder, and--as legume--enriches the soil with nitrogen. Eucalypts were included because most produce straight poles for construction, are drought-hardy, and are rated higher than Gmelina arborea in calorific value, durability, and strength. Another tree favored for its multiple uses is Leucaena leucocephala (Hawaiian giant), but it appears that there is considerable mixture of varieties in the seeds. With the exception of one trial at Bwanje, trials have not included farm crops, but the agroforestry element will be a very important consideration in future trials.

Respiratory symptoms and lung function in relation to wood dust and monoterpene exposure in the wood pellet industry.

Science.gov (United States)

Löfstedt, Håkan; Hagström, Katja; Bryngelsson, Ing-Liss; Holmström, Mats; Rask-Andersen, Anna

2017-06-01

Wood pellets are used as a source of renewable energy for heating purposes. Common exposures are wood dust and monoterpenes, which are known to be hazardous for the airways. The purpose of this study was to study the effect of occupational exposure on respiratory health in wood pellet workers. Thirty-nine men working with wood pellet production at six plants were investigated with a questionnaire, medical examination, allergy screening, spirometry, and nasal peak expiratory flow (nasal PEF). Exposure to wood dust and monoterpenes was measured. The wood pellet workers reported a higher frequency of nasal symptoms, dry cough, and asthma medication compared to controls from the general population. There were no differences in nasal PEF between work and leisure time. A lower lung function than expected (vital capacity [VC], 95%; forced vital capacity in 1 second [FEV 1 ], 96% of predicted) was noted, but no changes were noted during shifts. There was no correlation between lung function and years working in pellet production. Personal measurements of wood dust at work showed high concentrations (0.16-19 mg/m 3 ), and exposure peaks when performing certain work tasks. Levels of monoterpenes were low (0.64-28 mg/m 3 ). There was no association between exposure and acute lung function effects. In this study of wood pellet workers, high levels of wood dust were observed, and that may have influenced the airways negatively as the study group reported upper airway symptoms and dry cough more frequently than expected. The wood pellet workers had both a lower VC and FEV 1 than expected. No cross-shift changes were found.

Application of a CCA-treated wood waste decontamination process to other copper-based preservative-treated wood after disposal

Energy Technology Data Exchange (ETDEWEB)

Janin, Amelie, E-mail: amelie.janin@ete.inrs.ca [University of Toronto, Faculty of Forestry, 33, Willcocks St., Toronto, ON, M5S 3B3 (Canada); Coudert, Lucie, E-mail: lucie.coudert@ete.inrs.ca [Institut national de la recherche scientifique (Centre Eau, Terre et Environnement), Universite du Quebec, 490 rue de la Couronne, Quebec, QC, G1K 9A9 (Canada); Riche, Pauline, E-mail: pauline.riche@ete.inrs.ca [Institut national de la recherche scientifique (Centre Eau, Terre et Environnement), Universite du Quebec, 490 rue de la Couronne, Quebec, QC, G1K 9A9 (Canada); Mercier, Guy, E-mail: guy_mercier@ete.inrs.ca [Institut national de la recherche scientifique (Centre Eau, Terre et Environnement), Universite du Quebec, 490 rue de la Couronne, Quebec, QC, G1K 9A9 (Canada); Cooper, Paul, E-mail: p.cooper@utoronto.ca [University of Toronto, Faculty of Forestry, 33, Willcocks St., Toronto, ON, M5S 3B3 (Canada); Blais, Jean-Francois, E-mail: blaisjf@ete.inrs.ca [Institut national de la recherche scientifique (Centre Eau, Terre et Environnement), Universite du Quebec, 490 rue de la Couronne, Quebec, QC, G1K 9A9 (Canada)

2011-02-28

Research highlights: {yields} This paper describes a process for the metal removal from treated (CA-, ACQ- or MCQ-) wood wastes. {yields} This sulfuric acid leaching process is simple and economic. {yields} The remediated wood could be recycled in the industry. - Abstract: Chromated copper arsenate (CCA)-treated wood was widely used until 2004 for residential and industrial applications. Since 2004, CCA was replaced by alternative copper preservatives such as alkaline copper quaternary (ACQ), copper azole (CA) and micronized copper quaternary (MCQ), for residential applications due to health concerns. Treated wood waste disposal is becoming an issue. Previous studies identified a chemical process for decontaminating CCA-treated wood waste based on sulfuric acid leaching. The potential application of this process to wood treated with the copper-based preservatives (alkaline copper quaternary (ACQ), copper azole (CA) and micronized copper quaternary (MCQ)) is investigated here. Three consecutive leaching steps with 0.1 M sulfuric acid at 75 deg, C for 2 h were successful for all the types of treated wood and achieved more than 98% copper solubilisation. The different acidic leachates produced were successively treated by coagulation using ferric chloride and precipitation (pH = 7) using sodium hydroxide. Between 94 and 99% of copper in leachates could be recovered by electrodeposition after 90 min using 2 A electrical current. Thus, the process previously developed for CCA-treated wood waste decontamination could be efficiently applied for CA-, ACQ- or MCQ-treated wood.

Preparation of starch-g-polyacrylamide and its utilization as an adhesive for wood, paper and glass

International Nuclear Information System (INIS)

Abu-Ayana, Y.M.; Abou Zeid, N.Y.; Asran, A.Sh.; Aly, A.S.

2005-01-01

Starch- based adhesives are capable of wetting polar surfaces such as cellulose, penetrating pores, and forming strong bonds through mechanical and physical bonds. This paper studies the modification of starch by grafting with acrylamide, and the relation between modification and adhesion properties. Six formulae are prepared from modified and unmodified starch, and evaluated as adhesives for wood, glass, carton, and paper. Study of the factors affecting the adhesive bond is performed. Promising results are obtained. The adhesive formulae I-VI can be used successfully as paper and carton adhesives. Formulae I, TI and III can be used as wood adhesives. Excellent value for shear strength using formula No. I, comparable with other known thermoplastic and thermoset adhesives., formula I also can be used as glass adhesive, but in narrow applications and in absence of water

Bioremediation of treated wood with fungi

Science.gov (United States)

Barbara L. Illman; Vina W. Yang

2006-01-01

The authors have developed technologies for fungal bioremediation of waste wood treated with oilborne or metal-based preservatives. The technologies are based on specially formulated inoculum of wood-decay fungi, obtained through strain selection to obtain preservative-tolerant fungi. This waste management approach provides a product with reduced wood volume and the...

Weathering methods for preservative treated wood and their applicability for fire retarded wood

NARCIS (Netherlands)

Voss, A.

1999-01-01

preservative treated wood. The aim of the presentation is to inform you about current testing methods and to discuss their applicability to test fire retarded wood in outdoor use. Assuming that fire retardants will only be used in out of ground contact, only those methods are mentioned, which fit

Wood Export and Deposition Dynamics in Mountain Watersheds

Science.gov (United States)

Senter, Anne Elizabeth

Wood dynamics that store, transport, break down, and ultimately export wood pieces through watershed networks are key elements of stream complexity and ecosystem health. Efforts to quantify wood processes are advancing rapidly as technological innovations in field data collection, remotely sensed data acquisition, and data analyses become increasingly sophisticated. The ability to extend the temporal and spatial scales of wood data acquisition has been particularly useful to the investigations presented herein. The primary contributions of this dissertation are focused on two aspects of wood dynamics: watershed-scale wood export processes as identified using the depositional environment of a mountain reservoir, and wood deposition mechanisms in a bedrock-dominated mountain river. Three chapters present this work: In Chapter 1, continuous video monitoring of wood in transport revealed seasonal and diurnal hydrologic cycle influences on the variable rates at which wood transports. This effort supports the efficacy of utilizing continuous data collection methods for wood transport studies. Annual wood export data were collected via field efforts and aerial image analyses from New Bullards Bar Reservoir on the North Yuba River, Sierra Nevada, California. Examination of data revealed linkages between decadal-scale climatic patterns, large flood events, and episodic wood export quantities. A watershed-specific relation between wood export quantities and annual peak discharge contributes to the notion that peak discharge is a primary control on wood export, and yielded prediction of annual wood export quantities where no data were available. Linkages between seasonality, climatic components, and hydrologic events that exert variable control on watershed scale wood responses are presented as a functional framework. An accompanying conceptual model supports the framework presumption that wood responses are influenced by seasonal variations in Mediterranean-montane climate

Wood quality changes caused by mineral fertilization

Directory of Open Access Journals (Sweden)

Carlos Roberto Sette Jr

2014-06-01

Full Text Available The diverse and important use of wood from fast growth eucalyptus plantations requires the analysis of the effect of mineral fertilizers on wood quality. The objective of this study was to evaluate the anatomical characteristics and wood density from Eucalyptus grandis trees (3 m x 2 m spacing fertilized with potassium and sodium (at planting, 6 th and 12th month. Fifteen (15 6 years old eucalyptus trees were selected (5 trees/treatment, cut and wood samples at DBH (1,3 m were taken for anatomical characteristics (fiber and vessels and wood density analysis. Results showed that eucalyptus trees treated with mineral fertilizers did not show significant alteration in average wood density, with radial profile model common to all three treatments, characterized by a values increase in the region next to the pith, toward to bark. Mineral fertilization influenced wood anatomical characteristics: treatment with sodium was characterized by thinner walls and lumen larger diameter; in treatment with potassium, larger vessels were detected.

DEVELOPMENT OF STRUCTURES FROM SOLID WOOD FOR OBJECTS OF INFRASTRUCTURE

Directory of Open Access Journals (Sweden)

Konstantin P. Pyatikrestovsky

2018-03-01

Full Text Available New prefabricated lightweight structures made of solid wood with connections for joining and building metal screws for wood are proposed. Manufacture and assembly of basic elements-bars with a cross-section of 15x15 cm can be carried out in line conditions on the simplest woodworking equipment. The use of local tim-ber material has a number of advantages (ecological, economic and operational. The description of structures with manufacturing process, examples of buildings with vaulted and hipped roofing, connection arrangement, preparation of experimental samples with the use of new equipment of the National Research Moscow State University of Civil Engineering are given. The method of analysis with allowance for plastic deformations is under consideration. It provides additional economic advantages. The analysis is carried out by the method of integral estimates developed by Prof. V.M. Bondarenko for reinforced concrete structures and adapted to wooden structures by Prof. K.P. Pyatikrestovsky. Special strength criteria are used for the analysis of decks working together with the ribs (in a combined stressed state. It is planned to build buildings for various purposes in the ar-eas of development of the Far North of Russia.

CO2 abatement potential of wood utilisation. Wood as an energy carrier

International Nuclear Information System (INIS)

Wegener, G.; Fruehwald, A.

1994-01-01

Forests as ecosystems not only supply the raw material wood but also exert an influence on soils, water resources and many other ecological factors; provide animals with a habitat; and offer as humans a place for recreation. Recently, forests and wood have become of interest to human civilisation from yet another aspect: they constitute a carbon storage. This means that forestry and the forest industries can help moderate the increase of atmospheric CO 2 concentrations, which is essentially the result of energetic utilisation of fossil fuels and considered the decisive factor underlying the greenhouse effect. Besides constituting a carbon storage, forests hold an additional CO 2 abatement potential which can be realised by continuous utilisation of wood. (orig./EF) [de

Development of wood decay in wound-initiated discolored wood of eastern red cedar

Science.gov (United States)

Walter C. Shortle; Kenneth R. Dudzik; Kevin T. Smith

2010-01-01

Logs of eastern red cedar, Juniperus virginiana L., with well-developed bands of light-colored wood ("included sapwood") within heartwood can be unsuitable for sawn wood products. This finding is in contrast to published information that the "included sapwood" is (1) a heartwood anomaly rather than sapwood and (2) its occurrence...

Some contributions to the high strain rate deformation of solids and the thermally activated deformation of wood

International Nuclear Information System (INIS)

Ferguson, W George

2009-01-01

The behaviour of metals as a function of rate of loading, strain rate, and temperature is discussed in terms of previous work by the author. Strain rates range from 10 -3 s -1 , obtained in a standard tensile testing machine, to 10 2 s -1 obtained in a hydraulic piston driven machine and up to 10 4 s -1 , very high strain rates with a Kolsky split Hopkinson bar using shear type loading. At rates less 10 3 s -1 the strength is a function of strain rate and temperature, is thermally activated and governed by the stress-assisted thermal activation of dislocations across short-range barriers in the crystal. At very high strain rates however the behaviour is controlled by interaction of dislocations with either phonons or electrons, giving a strength proportional to strain rate. The compressive strength of small clear samples of wood, Pinus radiata and Kahikatea, determined over the strain rate range 10 -3 s -1 to 10 3 s -1 as a function of strain rate, temperature and moisture content shows the behaviour to again be thermally activated with the strength a function of stain rate, temperature and moisture content. A rate theory of deformation is developed where the yield behaviour of wood is assumed to result from the stress-assisted thermally activated motion of elementary fibrils over short-range barriers. The moisture is assumed to affect the bond energy between elementary fibrils and the barrier energy is taken to be a linear decreasing function of increasing moisture content and the moisture to act like a plasticiser in separating the elementary fibrils. The theory more than adequately explains the observed behaviour.

Fabrication and Performance of a Glue-Pressed Engineered Honeycomb Bamboo (GPEHB Structure with Finger-jointed Ends as a Potential Substitute for Wood Lumber

Directory of Open Access Journals (Sweden)

Jianbo Zhou

2015-04-01

Full Text Available With the increasing scarcity of wood as a natural resource, bamboo has become a popular substitute for wood. The present work developed a high-strength original state multi-reorganization material (GPEHB, without the use of a hot press or traditional assembly. The original bamboo units were polygonized into outer contours and milled into finger-joints on each ending. The GPEHB was organized and assembled under an external press, using industrial adhesives. The mechanical properties and thermal insulation of GPEHB were characterized. Moreover, the overall GPEHB unit bending strength was 73.15 MPa, and the parallel-to-grain compression was 55.22 MPa (higher than that of Pinus sylvestris lumber, though less than that of glued laminated bamboo. The GPEHB unit overall density was 0.24 g/cm³, 76% lower than that of glued laminated bamboo, and 50% lower than Pinus sylvestris lumber. The compressive strength of GPEHB (7 units was 170.5 kN, while the compressive strength of GPEHB for 14 units was 493.5 kN, which meet the requirements of GB 50005 (2003. The bending strength of GPEHB 7 units was 12 kN, while that of 14 units was 37 kN. The heat conductivity coefficient for GPEHB was 0.25 W/mK, which is better than concrete and steel. The GPEHB has taken full advantage of its honeycomb-structured material, which allows it to avoid stress concentration in the regular polygonal corners.

The extractives of Pinus pinaster wood

Science.gov (United States)

Richard W. Hemingway; W. E. Hillis; L. S. Lau

1973-01-01

The extractives in Pinus pinaster wood grown in South Australia were examined as part of an assessment of the suitability of this wood for manufacture of absorbent tissues from bisulphite pulps. The average petroleum solubility of the wood was 2.0% but the amount and composition of the petroleum extract varied widely depending upon the age of the...

Wood supply : what bioenergy resources are available as harvest residue and non-merchantable wood in New Brunswick?

International Nuclear Information System (INIS)

Forgrave, K.

2005-01-01

This paper examines resources available for bioenergy production in New Brunswick. An estimate of New Brunswick harvest levels, based on New Brunswick Forest Products Association web site figures was presented. Private wood lots harvest levels were also provided, with all estimates based on volume per year. Market conditions were discussed, with an emphasis on the dictates of price and availability for private wood lot owners. Market conditions and unused volume statistics were discussed. Various forest management options include the use of veneer, saw log, stud wood and pulp wood. Details of bioenergy percentages and potential were presented and general silviculture issues were discussed. It was concluded that many of the trade-offs of bioenergy involve placing more demands on forests, and that purchase prices will increasingly dictate volumes obtained from private wood lots. tabs, figs

Effects of wood polymers and extractives on the adsorption of wet-end chemicals and the properties of the sheet - MPKY 03

Energy Technology Data Exchange (ETDEWEB)

Bobacka, V.; Lindholm, J.; Nurmi, M.; Naesman, J. [Aabo Akademi, Turku (Finland). Lab. of Paper Chemistry; Holmbom, B.; Konn, J.; Sundberg, A.; Willfoer, S. [Aabo Akademi, Turku (Finland). Lab. of Forest Products Chemistry

1998-12-31

The effects of deposition of dissolved and colloidal substances (disco, DCS) together with fixing agents on the wet end chemistry, and the paper quality have been studied. Increased amounts of wood resin in handsheets results in lower strength properties and friction of the sheets. Addition of isolated polysaccharides together with wood resin results in higher strength properties compared, at the same resin content, to sheets without added polysaccharides. Disco substances released from TMP were adsorbed/deposited onto different fillers. It is possible to determine the distribution of aggregated wood resin in handsheets of kraft pulp by confocal laser scanning microscopy. Addition of iron salts to a TMP suspension results in a decrease in the brightness of the fibers. The adsorption of cationic starch and cationic polyacrylamide was studied as well as the flocculation of a peroxide bleached TMP and mixture of TMP and kraft pulp in the presence of retention aids and fixing agents. The fixing agent had a minor effect on the flocculation in peroxide bleached TMP, while cationic starch induced flocculation after a threshold. When added together, cationic starch induced flocculation immediately. The retention of carbohydrates in the mixture was not much influenced by the presence of fixing agents and retention aids, but the extractives were efficiently retained. Colloidal substances adsorb both cationic starch and polyacrylamide. Of the dissolved substances, pectic acids are most efficiently aggregated. (orig.)

Effects of wood polymers and extractives on the adsorption of wet-end chemicals and the properties of the sheet - MPKY 03

Energy Technology Data Exchange (ETDEWEB)

Bobacka, V; Lindholm, J; Nurmi, M; Naesman, J [Aabo Akademi, Turku (Finland). Lab. of Paper Chemistry; Holmbom, B; Konn, J; Sundberg, A; Willfoer, S [Aabo Akademi, Turku (Finland). Lab. of Forest Products Chemistry

1999-12-31

The effects of deposition of dissolved and colloidal substances (disco, DCS) together with fixing agents on the wet end chemistry, and the paper quality have been studied. Increased amounts of wood resin in handsheets results in lower strength properties and friction of the sheets. Addition of isolated polysaccharides together with wood resin results in higher strength properties compared, at the same resin content, to sheets without added polysaccharides. Disco substances released from TMP were adsorbed/deposited onto different fillers. It is possible to determine the distribution of aggregated wood resin in handsheets of kraft pulp by confocal laser scanning microscopy. Addition of iron salts to a TMP suspension results in a decrease in the brightness of the fibers. The adsorption of cationic starch and cationic polyacrylamide was studied as well as the flocculation of a peroxide bleached TMP and mixture of TMP and kraft pulp in the presence of retention aids and fixing agents. The fixing agent had a minor effect on the flocculation in peroxide bleached TMP, while cationic starch induced flocculation after a threshold. When added together, cationic starch induced flocculation immediately. The retention of carbohydrates in the mixture was not much influenced by the presence of fixing agents and retention aids, but the extractives were efficiently retained. Colloidal substances adsorb both cationic starch and polyacrylamide. Of the dissolved substances, pectic acids are most efficiently aggregated. (orig.)

Potential recovery of industrial wood and energy wood raw material in different cutting and climate scenarios for Finland

International Nuclear Information System (INIS)

Kaerkkaeinen, Leena; Nuutinen, Tuula; Matala, Juho; Kellomaeki, Seppo; Haerkoenen, Kari

2008-01-01

The aim of this study was to estimate the simultaneous recovery of industrial wood and raw material for energy wood from cuttings in Finland during the next 50 years. Two cutting scenarios (maximum and sustainable cuttings) and two climate scenarios (current and changing climate) were analysed to determine their impacts on harvesting potential. The analysis was carried out using sample plot and tree data from the ninth National Forest Inventory and a management-oriented large-scale forestry model (MELA) into which the transfer functions based on physiological modelling were incorporated to describe the impacts of climate change. Depending on the climate scenario, the volume of potential recovery of industrial wood in the maximum cutting scenario during the period 2003-2013 varied from 103 to 105 million m 3 a -1 , while the amount of potential energy wood raw material was 35 Tg a -1 . During the period 2043-2053, in the current climate scenario, the potential recovery of industrial wood was 64 million m 3 a -1 and energy wood raw material 22 Tg a -1 , and in the changing climate scenario, 85 million m 3 a -1 and 29 Tg a -1 , respectively. In the sustainable cutting scenario, depending on the climate scenario used, the potential recovery of industrial wood during the period 2003-2013 varied from 74 to 76 million m 3 a -1 , while the amount of potential energy wood was 25 Tg a -1 . During the period 2043-2053, in the current climate scenario, the potential recovery of industrial wood was 80 million m 3 a -1 and energy wood raw material 26 Tg a -1 , and in the changing climate scenario, 88 million m 3 a -1 and 29 Tg a -1 , respectively. (author)

Wood-based composite materials : panel products, glued-laminated timber, structural composite lumber, and wood-nonwood composite materials

Science.gov (United States)

Nicole M. Stark; Zhiyong Cai; Charles Carll

2010-01-01

This chapter gives an overview of the general types and composition of wood-based composite products and the materials and processes used to manufacture them. It describes conventional wood-based composite panels and structural composite materials intended for general construction, interior use, or both. This chapter also describes wood–nonwood composites. Mechanical...

Wood energy 2000; Bois energie 2000

Energy Technology Data Exchange (ETDEWEB)

Druette, L [Centre Scientifique et Technique du Batiment, (CSTB), 44 - Nantes (France); Lacome, T [AFNOR, 75 - Paris (France); Roy, C [Agence de l' Environnement et de la Maitrise de l' Energie, ADEME, 75 - Paris (France); and others

2000-07-01

The deregulation of the Electric Market and the opening of the Green Certificate exchange market force the set up of renewable energies. The wood, which is for most of european countries an important part of renewable fuel, should see the increase of its utilization. This conference on the wood energy deals the main aspects of this energy development. The papers present the wood burning furnaces technology assessment, the wood fuel market and the standardization of the appliances in this domain. Some papers also include the consequences of the big storms of december 1999. (A.L.B.)

Wood waste in Europe

Energy Technology Data Exchange (ETDEWEB)

Matos, O; Ribeiro, R [Biomass Centre for Energy - CBE, Miranda do Corvo (Portugal)

1998-12-31

The energy policy of the EC, as well as most of member states points to a sizeable increase of energy production based on renewable energy sources, wood, wood residues, agricultural residues, energy crops including SRF, organic sludges, solid residues, etc. Most recent goals indicate a desirable duplication of today`s percentage by 2010. The reasons for this interest, besides diversification of sources, less dependence on imported fuels, use of endogenous resources, expected decrease of fossil fuel reserves, use of available land, additional employment and income for rural communities, etc., are related to important environmental benefits namely in terms of emissions of hot house gases. Wood waste, resulting from forest operations, cleaning, cultural and final cuttings, and from wood based industries, constitute a special important resource by reason of quality and availability. In addition to this they do not require additional land use and the removal is beneficial. In the run-up to the becoming December`s 1997 `Climate Change Summit` in Kioto, there is mounting pressure on companies to plan on carbon cuts. (author) 6 refs., 1 tab.

Wood waste in Europe

Energy Technology Data Exchange (ETDEWEB)

Matos, O.; Ribeiro, R. [Biomass Centre for Energy - CBE, Miranda do Corvo (Portugal)

1997-12-31

The energy policy of the EC, as well as most of member states points to a sizeable increase of energy production based on renewable energy sources, wood, wood residues, agricultural residues, energy crops including SRF, organic sludges, solid residues, etc. Most recent goals indicate a desirable duplication of today`s percentage by 2010. The reasons for this interest, besides diversification of sources, less dependence on imported fuels, use of endogenous resources, expected decrease of fossil fuel reserves, use of available land, additional employment and income for rural communities, etc., are related to important environmental benefits namely in terms of emissions of hot house gases. Wood waste, resulting from forest operations, cleaning, cultural and final cuttings, and from wood based industries, constitute a special important resource by reason of quality and availability. In addition to this they do not require additional land use and the removal is beneficial. In the run-up to the becoming December`s 1997 `Climate Change Summit` in Kioto, there is mounting pressure on companies to plan on carbon cuts. (author) 6 refs., 1 tab.

Precision wood particle feedstocks

Science.gov (United States)

Dooley, James H; Lanning, David N

2013-07-30

Wood particles having fibers aligned in a grain, wherein: the wood particles are characterized by a length dimension (L) aligned substantially parallel to the grain, a width dimension (W) normal to L and aligned cross grain, and a height dimension (H) normal to W and L; the L.times.H dimensions define two side surfaces characterized by substantially intact longitudinally arrayed fibers; the W.times.H dimensions define two cross-grain end surfaces characterized individually as aligned either normal to the grain or oblique to the grain; the L.times.W dimensions define two substantially parallel top and bottom surfaces; and, a majority of the W.times.H surfaces in the mixture of wood particles have end checking.

Science supporting the economic and environmental benefits of using wood and wood products in green building construction

Science.gov (United States)

Michael A. Ritter; Kenneth Skog; Richard Bergman

2011-01-01

The objective of this report is to summarize the scientific findings that support the environmental and economic benefits of using wood and wood products in green building construction. Despite documented advantages in many peer-reviewed scientific articles, most building professionals and members of the public do not recognize wood as a renewable resource or the role...

Heat sterilization of wood

Science.gov (United States)

Xiping Wang

2010-01-01

Two important questions should be considered in heat sterilizing solid wood materials: First, what temperature–time regime is required to kill a particular pest? Second, how much time is required to heat the center of any wood configuration to the kill temperature? The entomology research on the first question has facilitated the development of international standards...

How James Wood Works

Science.gov (United States)

Goldstein, Evan R., Comp.

2008-01-01

Reading through news-media clippings about James Wood, one might reasonably conclude that "pre-eminent critic" is his official job title. In fact, Wood is a staff writer for "The New Yorker" and a professor of the practice of literary criticism at Harvard University. But at a time when there is much hand-wringing about the death of the…

INFLUENCE OF COCONUT SHELL ADDITION ON PHYSICO-MECHANICAL PROPERTIES OF WOOD PLASTIC COMPOSITES1

Directory of Open Access Journals (Sweden)

Éverton Hillig

2018-04-01

Full Text Available ABSTRACT In this study, composites with three types of thermoplastic matrix and cellulosic material in a proportion of 40% were produced. The three thermoplastic matrices were high density polyethylene (HDPE, polypropylene (PP and low density polyethylene (LDPE, and the cellulosic materials were pure wood flour (Pinus taeda L or a mixture of wood flour and coconut shell flour (Cocus nucifera L in equal ratios. The objective was to evaluate the influence of addition of coconut shell on the physico-mechanical properties (density, strength and rigidity and the distribution of the cellulosic material in the thermoplastic matrix of the manufactured composites. It was found that the composites had a satisfactory distribution of wood flour in thermoplastic matrices, but the addition of coconut shell promoted bubble formation in the resulting pieces and, thus, interfered with the material properties. The use of a coupling agent promoted interfacial adhesion (cellulose - thermoplastic matrix, which was better in high density polyethylene composites, followed by polypropylene and low density polyethylene. In general, the coconut shell addition caused a decrease of all properties compared to composites made with Loblolly Pine. In addition, the interactions between thermoplastic type and cellulosic matrix type have been statistically confirmed, which caused variations in the studied properties

Waste-wood resource supply assessment. Final report

International Nuclear Information System (INIS)

1991-08-01

The report documents and analyzes the availability and supply of wood waste in New York State to determine the type and amount currently generated to estimate its potential future use as a fuel. Detailed, current information is included on the availability, quantity and price of wood waste. Topics include wood waste markets; the harvesting and supply infrastructure; current and project prices; competing markets; environmental impacts of harvesting, processing and burning wood waste for fuel; and factors affecting long-term availability and supply. New York State's waste wood resource was evaluated to complete the Energy Authority's recent investigation of the potential role of wood in producing electric power. In 1989 approximately 11.8 million tons of wood waste were generated in New York State. More than 8 million tons or 68 percent, were disposed of by municipal solid waste and construction and demolition debris facilities. Just under 3.8 million tons or 32 percent, were reused and/or recycled. More than 25.7 million tons of wood waste could be available annually for fuel. Of the amount, more than 17.2 million tons per year, or 67 percent, could be produced by silvicultural activities that improve the health and productivity of forests

WGDB: Wood Gene Database with search interface.

Science.gov (United States)

Goyal, Neha; Ginwal, H S

2014-01-01

Wood quality can be defined in terms of particular end use with the involvement of several traits. Over the last fifteen years researchers have assessed the wood quality traits in forest trees. The wood quality was categorized as: cell wall biochemical traits, fibre properties include the microfibril angle, density and stiffness in loblolly pine [1]. The user friendly and an open-access database has been developed named Wood Gene Database (WGDB) for describing the wood genes along the information of protein and published research articles. It contains 720 wood genes from species namely Pinus, Deodar, fast growing trees namely Poplar, Eucalyptus. WGDB designed to encompass the majority of publicly accessible genes codes for cellulose, hemicellulose and lignin in tree species which are responsive to wood formation and quality. It is an interactive platform for collecting, managing and searching the specific wood genes; it also enables the data mining relate to the genomic information specifically in Arabidopsis thaliana, Populus trichocarpa, Eucalyptus grandis, Pinus taeda, Pinus radiata, Cedrus deodara, Cedrus atlantica. For user convenience, this database is cross linked with public databases namely NCBI, EMBL & Dendrome with the search engine Google for making it more informative and provides bioinformatics tools named BLAST,COBALT. The database is freely available on www.wgdb.in.

Southern Woods-Burners: A Descriptive Analysis

Science.gov (United States)

M.L. Doolittle; M.L. Lightsey

1979-01-01

About 40 percent of the South's nearly 60,000 wildfires yearly are set by woods-burners. A survey of 14 problem areas in four southern States found three distinct sets of woods-burners. Most active woods-burners are young, white males whose activities are supported by their peers. An older but less active group have probably retired from active participation but...

Cone calorimeter tests of wood composites

Science.gov (United States)

Robert H. White; Kuma Sumathipala

2013-01-01

The cone calorimeter is widely used for the determination of the heat release rate (HRR) of building products and other materials. As part of an effort to increase the availability of cone calorimeter data on wood products, the U.S. Forest Products Laboratory and the American Wood Council conducted this study on composite wood products in cooperation with the Composite...

Western Canadian wood residue production and consumption trends

International Nuclear Information System (INIS)

McCloy, B.

2006-01-01

This presentation considered various trends in western Canadian wood residue production and consumption. Potential markets for wood residue products were also discussed. Trends were reviewed by province for the years 2000-2004. British Columbia (BC) is currently the largest producer of residue in the country, and also retains the largest surpluses of bark, sawdust and shavings. Wood residues in BC are used in pulp and plywood mill production, as well as in the creation of particleboard and MDF. Surplus mill wood residue production in the province has greatly increased due to the Mountain Pine Beetle (MPB) infestation, which has in turn spurred expansion of the BC interior sawmill industry. The infestation has also resulted in a glut of pulp chips. Current wood residue products in Alberta are mostly used in pulp mill combined heat and power (CHP) systems, as well as for wood pellet production and the creation of particleboard and MDF. It was noted that surplus residues are rapidly declining in the province. Saskatchewan's wood residue storage piles are estimated to contain 2,900,000 BDt, while Manitoba surpluses are relatively minor. It was suggested that high natural gas prices have increased the payback on wood energy systems to approximately 2 years. The value of wood residue is now greater than $100/BDt as a substitute for natural gas once the wood energy system has been fully depreciated. Sawmills may now wish to consider equipping themselves to sell wood residue products, as most sawmills only require 20 per cent of their residues for heating purposes. It was concluded that markets for hog fuel wood pellets should be developed in Canada and internationally. Future markets may also develop if natural gas currently used in pulp mill power boilers and lime kilns is replaced with wood residue energy systems. refs., tabs., figs

Enhancement of the Mechanical Properties of Basalt Fiber-Wood-Plastic Composites via Maleic Anhydride Grafted High-Density Polyethylene (MAPE Addition

Directory of Open Access Journals (Sweden)

Yun Lu

2013-06-01

Full Text Available This study investigated the mechanisms, using microscopy and strength testing approaches, by which the addition of maleic anhydride grafted high-density polyethylene (MAPE enhances the mechanical properties of basalt fiber-wood-plastic composites (BF-WPCs. The maximum values of the specific tensile and flexural strengths are achieved at a MAPE content of 5%–8%. The elongation increases rapidly at first and then continues slowly. The nearly complete integration of the wood fiber with the high-density polyethylene upon MAPE addition to WPC is examined, and two models of interfacial behavior are proposed. We examined the physical significance of both interfacial models and their ability to accurately describe the effects of MAPE addition. The mechanism of formation of the Model I interface and the integrated matrix is outlined based on the chemical reactions that may occur between the various components as a result of hydrogen bond formation or based on the principle of compatibility, resulting from similar polarity. The Model I fracture occurred on the outer surface of the interfacial layer, visually demonstrating the compatibilization effect of MAPE addition.

Enhancement of the Mechanical Properties of Basalt Fiber-Wood-Plastic Composites via Maleic Anhydride Grafted High-Density Polyethylene (MAPE) Addition.

Science.gov (United States)

Chen, Jinxiang; Wang, Yong; Gu, Chenglong; Liu, Jianxun; Liu, Yufu; Li, Min; Lu, Yun

2013-06-18

This study investigated the mechanisms, using microscopy and strength testing approaches, by which the addition of maleic anhydride grafted high-density polyethylene (MAPE) enhances the mechanical properties of basalt fiber-wood-plastic composites (BF-WPCs). The maximum values of the specific tensile and flexural strengths are achieved at a MAPE content of 5%-8%. The elongation increases rapidly at first and then continues slowly. The nearly complete integration of the wood fiber with the high-density polyethylene upon MAPE addition to WPC is examined, and two models of interfacial behavior are proposed. We examined the physical significance of both interfacial models and their ability to accurately describe the effects of MAPE addition. The mechanism of formation of the Model I interface and the integrated matrix is outlined based on the chemical reactions that may occur between the various components as a result of hydrogen bond formation or based on the principle of compatibility, resulting from similar polarity. The Model I fracture occurred on the outer surface of the interfacial layer, visually demonstrating the compatibilization effect of MAPE addition.

Decay resistance of wood-plastic composites reinforced with extracted or delignified wood flour

Science.gov (United States)

Rebecca E. Ibach; Yao Chen; Nicole M. Stark; Mandla A. Tshabalala; Yongming Fan; Jianmin Gao

2014-01-01

The moisture and decay resistance of wood-plastic composites (WPCs) reinforced with extracted or delignified wood flour (WF) was investigated. Three different extractions were preformed: toluene/ethanol (TE), acetone/water (AW), and hot water (HW). Delignification (DL) was performed using a sodium chlorite/acetic acid solution. All WPCs specimens were made with 50% by...

Experimental Investigation on Embedding Strength Perpendicular to Grain of Parallel Strand Bamboo

Directory of Open Access Journals (Sweden)

Junwen Zhou

2018-01-01

Full Text Available Parallel strand bamboo (PSB is a latest construction material; to know more about mechanical properties of PSB, 5 groups of specimens with difference only in bolt diameter were designed to study the impact of the fastener diameter on embedding strength perpendicular to grain of PSB. Based on the tested result, the feasibility for PSB of the theoretical equation in the American code and European code on embedding strength predication was assessed. A controlled displacement was used to load till specimen failure, the stress-displacement curve of all specimens was obtained in terms of the tested results, and the yielding tested strength based on 5% bolt diameter offset proposed by the American code was found. The tested results showed that the yielding strength perpendicular to grain of PSB was stable, the variable coefficient was between 5.88% and 13.34%, and the average yielding strength values were 80.84 MPa, 77.40 MPa, 76.52 MPa, 74.20 MPa, and 67.01 MPa, respectively, which decreased with the increase of bolt diameter, and the average yielding strength values are larger than the calculated results using theoretical formula. Therefore, the theoretical equation on embedding yielding strength of wood in the American code and European code applies to PSB.

5000 sustainable workplaces - Wood energy provides work

International Nuclear Information System (INIS)

Keel, A.

2009-01-01

This article presents the results of a study made by the Swiss Wood Energy Association on the regional and national added value resulting from large wood-fired installations in Switzerland. The number of workplaces created by these installations is also noted. Wood energy is quoted as not only being a way of using forest wastes but also as being a creator of employment. Large wood-fired heating installations are commented on and efforts to promote this type of energy supply even further are discussed. The study indicates which professions benefit from the use of wood energy and quantifies the number of workplaces per megawatt of installed power that result.

Corrosion of metals in wood : comparing the results of a rapid test method with long-term exposure tests across six wood treatments

Science.gov (United States)

Samuel L. Zelinka; Donald S. Stone

2011-01-01

This paper compares two methods of measuring the corrosion of steel and galvanized steel in wood: a long-term exposure test in solid wood and a rapid test method where fasteners are electrochemically polarized in extracts of wood treated with six different treatments. For traditional wood preservatives, the electrochemical extract method correlates with solid wood...

USE OF CANDEIA’S (Eremanthus erythropappus WASTE WOOD

Directory of Open Access Journals (Sweden)

Rosimeire Cavalcante dos Santos

2008-09-01

Full Text Available The candeia (Eremanthus erythropappus is a native forest species with multiple uses and specially utilized as essential oils source. The use of the candeia´s waste wood after oil extraction for particle panels production becomes a viable alternative, avoiding environmental problems and increasing the availability of these products in the consuming market. This work verified the viability of producing wood-cement panels using waste wood generated after the extraction of candeia’s oil, in association with pinus and eucalipto woods. The experiment was installed according to a completely randomized design with three repetitions. The treatments were arranged according to a factorial 2 x 3 scheme (two wooden species and three replacement percentages of the woods by candeia’s waste. The results of the physical and mechanical property tests showed high potentiality of candeia waste wood, after oil extraction, in association with pinus and eucalipto wood for manufacturing wood-cement panels.

Wood energy barometer. 43 million toe produced in 2003

International Nuclear Information System (INIS)

Anon.

2004-01-01

The use of wood in the form of energy contributes in fighting global warming since, unlike fossil energies, the carbon dioxide emitted by its combustion is reabsorbed by the forests. These environmental and energetic advantages explain why the European Union large wood countries are preparing programmes to develop both wood energy technologies and wood energy consumption; This document takes stock or gives information on the breakdown of valorization of wood energy origin primary energy, the gross electricity generation from wood energy in the 15 european union countries and Poland, the primary energy from wood energy, the comparative between different wood energy fuel prices in Europe, the number of direct and indirect job created in different sectors, the wood energy sector industrialists and a comparison between current trend and white paper objectives. (A.L.B.)

Furniture wood wastes: Experimental property characterisation and burning tests

International Nuclear Information System (INIS)

Tatano, Fabio; Barbadoro, Luca; Mangani, Giovanna; Pretelli, Silvia; Tombari, Lucia; Mangani, Filippo

2009-01-01

Referring to the industrial wood waste category (as dominant in the provincial district of Pesaro-Urbino, Marche Region, Italy), this paper deals with the experimental characterisation and the carrying out of non-controlled burning tests (at lab- and pilot-scale) for selected 'raw' and primarily 'engineered' ('composite') wood wastes. The property characterisation has primarily revealed the following aspects: potential influence on moisture content of local weather conditions at outdoor wood waste storage sites; generally, higher ash contents in 'engineered' wood wastes as compared with 'raw' wood wastes; and relatively high energy content values of 'engineered' wood wastes (ranging on the whole from 3675 to 5105 kcal kg -1 for HHV, and from 3304 to 4634 kcal kg -1 for LHV). The smoke qualitative analysis of non-controlled lab-scale burning tests has primarily revealed: the presence of specific organic compounds indicative of incomplete wood combustion; the presence exclusively in 'engineered' wood burning tests of pyrroles and amines, as well as the additional presence (as compared with 'raw' wood burning) of further phenolic and containing nitrogen compounds; and the potential environmental impact of incomplete industrial wood burning on the photochemical smog phenomenon. Finally, non-controlled pilot-scale burning tests have primarily given the following findings: emission presence of carbon monoxide indicative of incomplete wood combustion; higher nitrogen oxide emission values detected in 'engineered' wood burning tests as compared with 'raw' wood burning test; and considerable generation of the respirable PM 1 fraction during incomplete industrial wood burning.

Wood-Based Nanotechnologies toward Sustainability.

Science.gov (United States)

Jiang, Feng; Li, Tian; Li, Yiju; Zhang, Ying; Gong, Amy; Dai, Jiaqi; Hitz, Emily; Luo, Wei; Hu, Liangbing

2018-01-01

With over 30% global land coverage, the forest is one of nature's most generous gifts to human beings, providing shelters and materials for all living beings. Apart from being sustainable, renewable, and biodegradable, wood and its derivative materials are also extremely fascinating from a materials aspect, with numerous advantages including porous and hierarchical structure, excellent mechanical performance, and versatile chemistry. Here, strategies for designing novel wood-based materials via advanced nanotechnologies are summarized, including both the controllable bottom-up assembly from the highly crystalline nanocellulose building block and the more efficient top-down approaches directly from wood. Beyond material design, recent advances regarding the sustainable applications of these novel wood-based materials are also presented, focusing on areas that are traditionally dominated by man-made nonrenewable materials such as plastic, glass, and metals, as well as more advanced applications in the areas of energy storage, wastewater treatment and solar-steam-assisted desalination. With all recent progress pertaining to materials' design and sustainable applications presented, a vision for the future engineering of wood-based materials to promote continuous and healthy progress toward true sustainability is outlined. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Wood decomposition as influenced by invertebrates.

Science.gov (United States)

Ulyshen, Michael D

2016-02-01

The diversity and habitat requirements of invertebrates associated with dead wood have been the subjects of hundreds of studies in recent years but we still know very little about the ecological or economic importance of these organisms. The purpose of this review is to examine whether, how and to what extent invertebrates affect wood decomposition in terrestrial ecosystems. Three broad conclusions can be reached from the available literature. First, wood decomposition is largely driven by microbial activity but invertebrates also play a significant role in both temperate and tropical environments. Primary mechanisms include enzymatic digestion (involving both endogenous enzymes and those produced by endo- and ectosymbionts), substrate alteration (tunnelling and fragmentation), biotic interactions and nitrogen fertilization (i.e. promoting nitrogen fixation by endosymbiotic and free-living bacteria). Second, the effects of individual invertebrate taxa or functional groups can be accelerative or inhibitory but the cumulative effect of the entire community is generally to accelerate wood decomposition, at least during the early stages of the process (most studies are limited to the first 2-3 years). Although methodological differences and design limitations preclude meta-analysis, studies aimed at quantifying the contributions of invertebrates to wood decomposition commonly attribute 10-20% of wood loss to these organisms. Finally, some taxa appear to be particularly influential with respect to promoting wood decomposition. These include large wood-boring beetles (Coleoptera) and termites (Termitoidae), especially fungus-farming macrotermitines. The presence or absence of these species may be more consequential than species richness and the influence of invertebrates is likely to vary biogeographically. Published 2014. This article is a U.S. Government work and is in the public domain in the USA.

Wood Programs. Courseware Evaluation for Vocational and Technical Education.

Science.gov (United States)

Kaylor, Robert; And Others

This courseware evaluation rates the Wood Programs software developed by the Iowa Department of Public Instruction. (These programs--not contained in this document--include understanding board feet, wood characteristics, wood safety drill, wood dimensions, wood moisture, operating the table saw, radial arm, measurement drill, fraction drill, and…

COMBUSTION PROPERTIES OF EUCALYPTUS WOOD

Directory of Open Access Journals (Sweden)

Yalçın ÖRS

1999-03-01

Full Text Available In this study, the combustion properties of some impregnation materials (abiotic and biotic factors used for eucalyptus wood in interior or exterior environments were investigated. The experimental samples were prepared from Eucalyptus wood based on ASTM-D-1413-76 Tanalith-CBC, boric acid, borax, vacsol-WR, immersol-WR, polyethylen glycole-400 and ammonium sulphate were used as an impregnation material. The results indicated that, vacuum treatment on Eucalyptus gave the lowest retention value of salts. Compounds containing boron+salt increased fire resistance however water repellents decreased the wood flammability.

European wood-pastures in transition

DEFF Research Database (Denmark)

Wood-pastures are important elements of European cultural identity and have an exceptional ecological value, yet they are in decline all over Europe. The structure of wood-pastures is strongly influenced by grazing and multiple other land uses and by local and regional environmental conditions....... This book examines the diverse expressions of wood-pastures across Europe. It provides a new perspective, using a social-ecological framework to explore social and ecological values, governing institutions, threats and conservation approaches. It explores the major drivers of decline, which are shown...

Variation in root wood anatomy

NARCIS (Netherlands)

Cutler, D.F.

1976-01-01

Variability in the anatomy of root wood of selected specimens particularly Fraxinus excelsior L. and Acer pseudoplatanus L. in the Kew reference microscope slide collection is discussed in relation to generalised statements in the literature on root wood anatomy.

Properties of wood-plastic composites (WPCs) reinforced with extracted and delignified wood flour

Science.gov (United States)

Yao Chen; Nicole M. Stark; Mandla A. Tshabalala; Jianmin Gao; Yongming Fan

2014-01-01

The water sorption and mechanical properties of wood-plastic composites (WPCs) made of extracted and delignified wood flour (WF) has been investigated. WF was prepared by extraction with the solvent systems toluene/ethanol (TE), acetone/water (AW), and hot water (HW), and its delignification was conducted by means of sodium chlorite/acetic acid (AA) solution. A 2 4...

Application of tung oil to improve adhesion strength and water resistance of cottonseed meal and protein adhesives on maple veneer

Science.gov (United States)

Cottonseed meal-based products show promise in serving as environment-friendly wood adhesives. However, their practical utilization is currently limited due to low durability and water resistant properties. In this research, we tested the improvement of adhesion strength and water resistance of cott...

Wood energy in Switzerland - fillet steaks and sausages

International Nuclear Information System (INIS)

Keel, A.

2004-01-01

This article discusses the increasing use of wood energy to help meet Switzerland's energy needs. The increasing interest in wood-fired systems in comparison with fossil fuels is commented on. The article presents figures on energy carriers and the shares of the energy supply they meet as well as the development of wood-fired systems between 1991 and 2003. The influence of Swiss regional identities on the market for wood heating systems is discussed, as are difficulties resulting from stop-and-go governmental promotional funding. The importance of wood-fired energy systems for local authorities with difficulties in selling wood from their communal forestry departments is also discussed

Effect of carbonization temperature on the microplasticity of wood-derived biocarbon

Science.gov (United States)

Shpeizman, V. V.; Orlova, T. S.; Kardashev, B. K.; Smirnov, B. I.; Gutierrez-Pardo, A.; Ramirez-Rico, J.

2014-03-01

The uniaxial compression strength under stepped loading and the 325-nm-stepped deformation rate of biocarbon samples obtained by carbonization of beech wood at different temperatures in the 600-1600°C range have been measured using high-precision interferometry. It has been shown that the strength depends on the content of nanocrystalline phase in biocarbon. The magnitude of deformation jumps at micro- and nanometer levels and their variation with a change in the structure of the material and loading time have been determined. For micro- and nanometer-scale jumps, standard deviations of the differences between the experimentally measured deformation rate at loading steps and its magnitude at the smoothed fitting curve have been calculated, and the correlation of the error with the deformation prior to destruction has been shown. The results obtained have been compared with the previously published data on measurements of the elastic properties and internal friction of these materials.

Forest biomass and wood waste resources

Science.gov (United States)

K. Skog; P. Lebow; D.. Dykstra; P.. Miles; B.J. Stokes; R.D. Perlack; M. Buford; J. Barbour; D. McKeever

2011-01-01

This chapter provides estimates of forest biomass and wood waste quantities, as well as roadside costs (i.e., supply curves) for each county in the contiguous United States. Roadside price is the price a buyer pays for wood chips at a roadside in the forest, at a processing mill location in the case of mill residue, or at a landfill for urban wood wastes prior to any...

The wood, renewable energy

International Nuclear Information System (INIS)

Acket, C.

2006-12-01

This document evaluates the french forest situation and its future. Indeed, the wood energy constitutes in France the first renewable energy after the hydraulic. It presents the today situation of the french forest providing statistical data, evaluation of the energy estimation, the carbon fixation, the resources, the perspectives wood energy for 2050, the biofuels and an economic analysis. (A.L.B.)

Wood supply and demand

Science.gov (United States)

Peter J. Ince; David B. McKeever

2011-01-01

At times in history, there have been concerns that demand for wood (timber) would be greater than the ability to supply it, but that concern has recently dissipated. The wood supply and demand situation has changed because of market transitions, economic downturns, and continued forest growth. This article provides a concise overview of this change as it relates to the...

Chemical modification of wood

Science.gov (United States)

Roger M. Rowell

2007-01-01

After millions of years of evolution, wood was designed to perform in a wet environment, and nature is programmed to recycle it, in a timely way, back to the basic building blocks of carbon dioxide and water through biological, thermal, aqueous, photochemical, chemical, and mechanical degradation. The properties of wood are, for the most part, a result of the chemistry...

Utilisation of Estonian energy wood resources

Energy Technology Data Exchange (ETDEWEB)

Muiste, P.; Tullus, H.; Uri, V. [Estonian Agricultural University, Tartu (Estonia)

1996-12-31

In the end of the Soviet period in the 1980s, a long-term energy programme for Estonia was worked out. The energy system was planned to be based on nuclear power and the share of domestic alternative sources of energy was low. The situation has greatly changed after the re-establishment of the Estonian independence, and now wood and peat fuels play an important role in the energy system. Energy consumption in Estonia decreased during the period 1970-1993, but this process has less influenced the consumption of domestic renewable fuels - peat and wood. It means that the share of these fuels has grown. The investment on substitution of imported fossil fuels and on conversion of boiler plants from fossil fuels to domestic fuels has reached the level of USD 100 million. The perspectives of the wood energy depend mainly on two factors; the resources and the price of wood energy compared with other fuels. The situation in wood market influences both the possible quantities and the price. It is typical that the quickly growing cost of labour power in Estonia is greatly affecting the price of energy wood. Though the price level of fuel peat and wood chips is lower than the world market price today, the conditions for using biofuels could be more favourable, if higher environmental fees were introduced. In conjunction with increasing utilisation of biofuels it is important to evaluate possible emissions or removal of greenhouse gases from Estonian forests 3 refs.

Utilisation of Estonian energy wood resources

Energy Technology Data Exchange (ETDEWEB)

Muiste, P; Tullus, H; Uri, V [Estonian Agricultural University, Tartu (Estonia)

1997-12-31

In the end of the Soviet period in the 1980s, a long-term energy programme for Estonia was worked out. The energy system was planned to be based on nuclear power and the share of domestic alternative sources of energy was low. The situation has greatly changed after the re-establishment of the Estonian independence, and now wood and peat fuels play an important role in the energy system. Energy consumption in Estonia decreased during the period 1970-1993, but this process has less influenced the consumption of domestic renewable fuels - peat and wood. It means that the share of these fuels has grown. The investment on substitution of imported fossil fuels and on conversion of boiler plants from fossil fuels to domestic fuels has reached the level of USD 100 million. The perspectives of the wood energy depend mainly on two factors; the resources and the price of wood energy compared with other fuels. The situation in wood market influences both the possible quantities and the price. It is typical that the quickly growing cost of labour power in Estonia is greatly affecting the price of energy wood. Though the price level of fuel peat and wood chips is lower than the world market price today, the conditions for using biofuels could be more favourable, if higher environmental fees were introduced. In conjunction with increasing utilisation of biofuels it is important to evaluate possible emissions or removal of greenhouse gases from Estonian forests 3 refs.

A geographical analysis of the Swedish wood fuel market

International Nuclear Information System (INIS)

Roos, Anders; Bohlin, Folke; Hektor, Bo; Hillring, Bengt; Parikka, Matti

2000-01-01

The geographical variation in Swedish wood fuel market characteristics for the district heating sector has been studied using Geographical Information Systems (GIS) and cross-sectional Tobit analysis. The results indicate that local availability and competition for wood fuels influence the wood fuel consumption at inland heating plants. The factors affecting the decision to use wood fuel at heating plants close to seaports, however, were not captured by the model, suggesting that coastal location reduces dependency on the local wood fuel market. The effects of changes in local wood fuel availability on wood fuel use by an inland heating plant are presented and discussed

Construction of Hydrophobic Wood Surface and Mechanical Property of Wood Cell Wall on Nanoscale Modified by Dimethyldichlorosilane

Science.gov (United States)

Yang, Rui; Wang, Siqun; Zhou, Dingguo; Zhang, Jie; Lan, Ping; Jia, Chong

2018-01-01

Dimethyldichlorosilane was used to improve the hydrophobicity of wood surface. The water contact angle of the treated wood surface increased from 85° to 143°, which indicated increased hydrophobicity. The nanomechanical properties of the wood cell wall were evaluated using a nanoindentation test to analyse the hydrophobic mechanism on the nano scale. The elastic modulus of the cell wall was significantly affected by the concentration but the influence of treatment time is insignificant. The hardness of the cell wall for treated samples was significantly affected by both treatment time and concentration. The interaction between treatment time and concentration was extremely significant for the elastic modulus of the wood cell wall.