WorldWideScience

Sample records for wood chip beds

  1. Potential of synthesis gas production from rubber wood chip gasification in a bubbling fluidised bed gasifier

    International Nuclear Information System (INIS)

    Kaewluan, Sommas; Pipatmanomai, Suneerat

    2011-01-01

    Experiments of rubber wood chip gasification were carried out in a 100-kW th bubbling fluidised bed gasifier to investigate the effect of air to fuel ratio (represented as equivalence ratio - ER) on the yield and properties of synthesis gas. For all experiments, the flow rate of ambient air was fixed, while the feed rate of rubber wood chip was adjusted to vary ER in the range of 0.32-0.43. Increasing ER continuously raised the bed temperature, which resulted in higher synthesis gas yield and lower yield of ash and tar. However, higher ER generally gave synthesis gas of lower heating value, partly due to the dilution of N 2 . Considering the energy efficiency of the process, the optimum operation was achieved at ER = 0.38, which yielded 2.33 Nm 3 of synthesis gas per kg of dry biomass at the heating value of 4.94 MJ/Nm 3 . The calculated carbon conversion efficiency and gasification efficiency were 97.3% and 80.2%, respectively. The mass and energy balance of the gasification process showed that the mass and energy distribution was significantly affected by ER and that the energy losses accounted for ∼25% of the total output energy. The economical assessment of synthesis gas utilisation for heat and electricity production based on a 1-MW th bubbling fluidised bed gasifier and the operational data resulting from the rubber wood chip gasification experiments in this study clearly demonstrated the attractiveness of replacing heavy fuel oil and natural gas by the synthesis gas for heat applications in terms of 70% and 50% annual saving of fuel cost, respectively. However, the case of electricity production does not seem a preferable option due to its current technical and non-technical barriers.

  2. Low-NO{sub x}, wood chip combustion

    Energy Technology Data Exchange (ETDEWEB)

    Saastamoinen, J.; Oravainen, H.; Haemaelaeinen, J.; Paakkinen, K. [VTT Energy, Jyvaeskylae (Finland)

    1997-10-01

    The regulations for nitrogen oxide emissions vary in different countries, but the general trend in the future will probably be that the emissions limits will be lowered also for wood combustion plants, which are small or medium size units. Thus, the development of wood chip burning furnaces (grate furnaces, fluidized bed combustors, stoker furnaces) with lower nitrogen oxide emissions, is important. The wood used in the combustor, its particle size, moisture and fuel properties (nitrogen content) affect the nitrogen emissions. The nitrogen oxide release is also much affected by the design and operation of the combustor (air staging, fuel air preheat, flue gas circulation, air to fuel mass ratio). The fate of nitrogen compounds originally in the virgin wood depends much on the design of the combustor system and by proper planning it is possible to reduce the emission of nitrogen oxides. Basic knowledge of the release of nitrogen compounds from single wood particles is attained. The release of gaseous nitrogen compounds from wood particles during pyrolysis and combustion is studied experimentally and by modelling. Nitrogen release is studied experimentally by two ways, by analysing the gas and by quenching the particle and analysing the char residue. Formation of nitrogen oxide emissions in a fuel bed is studied by modelling and by combustion experiments with a pot furnace. This research gives general information of nitrogen oxide formation in wood bunting especially in fixed beds. The development of a horizontal stoker burner for wood chips with low emissions is the practical aim of the research. (orig.)

  3. Modelling and simulation of wood chip combustion in a hot air generator system.

    Science.gov (United States)

    Rajika, J K A T; Narayana, Mahinsasa

    2016-01-01

    This study focuses on modelling and simulation of horizontal moving bed/grate wood chip combustor. A standalone finite volume based 2-D steady state Euler-Euler Computational Fluid Dynamics (CFD) model was developed for packed bed combustion. Packed bed combustion of a medium scale biomass combustor, which was retrofitted from wood log to wood chip feeding for Tea drying in Sri Lanka, was evaluated by a CFD simulation study. The model was validated by the experimental results of an industrial biomass combustor for a hot air generation system in tea industry. Open-source CFD tool; OpenFOAM was used to generate CFD model source code for the packed bed combustion and simulated along with an available solver for free board region modelling in the CFD tool. Height of the packed bed is about 20 cm and biomass particles are assumed to be spherical shape with constant surface area to volume ratio. Temperature measurements of the combustor are well agreed with simulation results while gas phase compositions have discrepancies. Combustion efficiency of the validated hot air generator is around 52.2 %.

  4. Preservation of forest wood chips

    Energy Technology Data Exchange (ETDEWEB)

    Kofman, P.D.; Thomsen, I.M.; Ohlsson, C.; Leer, E.; Ravn Schmidt, E.; Soerensen, M.; Knudsen, P.

    1999-01-01

    As part of the Danish Energy Research Programme on biomass utilisation for energy production (EFP), this project concerns problems connected to the handling and storing of wood chips. In this project, the possibility of preserving wood chips of the Norway Spruce (Picea Abies) is addressed, and the potential improvements by anaerobic storage are tested. Preservation of wood chips aims at reducing dry matter losses from extensive heating during storage and to reduce production of fungal spores. Fungal spores pose a health hazards to workers handling the chips. Further the producers of wood chips are interested in such a method since it would enable them to give a guarantee for the delivery of homogeneous wood chips also during the winter period. Three different types of wood chips were stored airtight and further one of these was stored in accordance with normal practise and use as reference. The results showed that airtight storage had a beneficial impact on the quality of the chips: no redistribution of moisture, low dry matter losses, unfavourable conditions for microbial activity of most fungi, and the promotion of yeasts instead of fungi with airborne spores. Likewise the firing tests showed that no combustion problems, and no increased risk to the environment or to the health of staff is caused by anaerobic storage of wood chips. In all, the tests of the anaerobic storage method of forest wood chips were a success and a large-scale test of the method will be carried out in 1999. (au)

  5. Oxygen Carrier Aided Combustion (OCAC of Wood Chips in a Semi-Commercial Circulating Fluidized Bed Boiler Using Manganese Ore as Bed Material

    Directory of Open Access Journals (Sweden)

    Magnus Rydén

    2016-11-01

    Full Text Available Oxygen Carrier Aided Combustion (OCAC is realized by using an active oxygen-carrying bed material in fluidized bed boilers. The active material is reduced in fuel rich parts of the boiler and oxidized in air rich parts. Advantages could be achieved such as new mechanisms for oxygen transport in space and time. Here calcined manganese ore has been used as active bed material in a 12 MWth circulating fluidized bed boiler. The fuel was wood chips and the campaign lasted more than two weeks. From an operational point of view, manganese ore worked excellently. From the temperature profile of the boiler it can be concluded that fuel conversion was facilitated, especially in the dense bottom bed. The effect did not always translate to reduced emissions, which suggests that final combustion in the cyclone outlet was also influenced. Substituting 10% of the sand bed with manganese ore made it possible to reduce the air to fuel ratio without generating large amounts of CO. The use of 100% manganese ore resulted in higher emissions of CO than the sand reference, but, when combined sulphur feeding, dramatic reductions in CO emissions, up to 90% compared to sand reference, was achieved.

  6. Pelly Crossing wood chip boiler

    Energy Technology Data Exchange (ETDEWEB)

    1985-03-11

    The Pelly wood chip project has demonstrated that wood chips are a successful fuel for space and domestic water heating in a northern climate. Pelly Crossing was chosen as a demonstration site for the following reasons: its extreme temperatures, an abundant local supply of resource material, the high cost of fuel oil heating and a lack of local employment. The major obstacle to the smooth operation of the boiler system was the poor quality of the chip supply. The production of poor quality chips has been caused by inadequate operation and maintenance of the chipper. Dull knives and faulty anvil adjustments produced chips and splinters far in excess of the one centimetre size specified for the system's design. Unanticipated complications have caused costs of the system to be higher than expected by approximately $15,000. The actual cost of the project was approximately $165,000. The first year of the system's operation was expected to accrue $11,600 in heating cost savings. This estimate was impossible to confirm given the system's irregular operation and incremental costs. Consistent operation of the system for a period of at least one year plus the installation of monitoring devices will allow the cost effectiveness to be calculated. The wood chip system's impact on the environment was estimated to be minimal. Wood chip burning was considered cleaner and safer than cordwood burning. 9 refs., 6 figs., 6 tabs.

  7. Ammonia, Total Reduced Sulfides, and Greenhouse Gases of Pine Chip and Corn Stover Bedding Packs.

    Science.gov (United States)

    Spiehs, Mindy J; Brown-Brandl, Tami M; Parker, David B; Miller, Daniel N; Berry, Elaine D; Wells, James E

    2016-03-01

    Bedding materials may affect air quality in livestock facilities. Our objective in this study was to compare headspace concentrations of ammonia (NH), total reduced sulfides (TRS), carbon dioxide (CO), methane (CH), and nitrous oxide (NO) when pine wood chips ( spp.) and corn stover ( L.) were mixed in various ratios (0, 10, 20, 30, 40, 60, 80, and 100% pine chips) and used as bedding with manure. Air samples were collected from the headspace of laboratory-scaled bedded manure packs weekly for 42 d. Ammonia concentrations were highest for bedded packs containing 0, 10, and 20% pine chips (equivalent to 501.7, 502.3, and 502.3 mg m, respectively) in the bedding mixture and were lowest when at least 80% pine chips were used as bedding (447.3 and 431.0 mg m, respectively for 80 and 100% pine chip bedding). The highest NH concentrations were observed at Day 28. The highest concentration of TRS was observed when 100% pine chips were used as bedding (11.4 µg m), with high concentrations occurring between Days 7 and 14, and again at Day 35. Greenhouse gases were largely unaffected by bedding material but CH and CO concentrations increased as the bedded packs aged and NO concentrations were highly variable throughout the incubation. We conclude that a mixture of bedding material that contains 30 to 40% pine chips may be the ideal combination to reduce both NH and TRS emissions. All gas concentrations increased as the bedded packs aged, suggesting that frequent cleaning of facilities would improve air quality in the barn, regardless of bedding materials used. Copyright © by the American Society of Agronomy, Crop Science Society of America, and Soil Science Society of America, Inc.

  8. Firing with wood chips in heating and cogeneration plants

    International Nuclear Information System (INIS)

    Kofman, P.D.

    1992-01-01

    The document was produced for use as detailed teaching material aimed at spreading information on the use of wood chips as fuel for heating and cogeneration plants. It includes information and articles on wood fuels generally, combustion values, chopping machines, suppliers, occupational health hazards connected with the handling of wood chips, measuring amounts, the selection of types, prices, ash, environmental aspects and information on the establishment of a wood-chip fired district heating plant. (AB)

  9. Least cost supply strategies for wood chips

    DEFF Research Database (Denmark)

    Möller, Bernd

    The abstract presents a study based on a geographical information system, which produce  cost-supply curves by location for forest woods chips in Denmark.......The abstract presents a study based on a geographical information system, which produce  cost-supply curves by location for forest woods chips in Denmark....

  10. Ammonia, total reduced sulfides, and greenhouse gases of pine chip and corn stover bedding packs

    Science.gov (United States)

    Bedding materials may affect air quality in livestock facilities. The objective of this study was to compare headspace concentrations of ammonia (NH3), total reduced sulfides (TRS), carbon dioxide (CO2),methane (CH4), and nitrous oxide (N2O) when pine wood chips and corn stover were mixed in various...

  11. Biomass energy from wood chips: Diesel fuel dependence?

    International Nuclear Information System (INIS)

    Timmons, Dave; Mejia, Cesar Viteri

    2010-01-01

    Most renewable energy sources depend to some extent on use of other, non-renewable sources. In this study we explore use of diesel fuel in producing and transporting woody biomass in the state of New Hampshire, USA. We use two methods to estimate the diesel fuel used in woody biomass production: 1) a calculation based on case studies of diesel consumption in different parts of the wood chip supply chain, and 2) to support extrapolating those results to a regional system, an econometric study of the variation of wood-chip prices with respect to diesel fuel prices. The econometric study relies on an assumption of fixed demand, then assesses variables impacting supply, with a focus on how the price of diesel fuel affects price of biomass supplied. The two methods yield similar results. The econometric study, representing overall regional practices, suggests that a $1.00 per liter increase in diesel fuel price is associated with a $5.59 per Mg increase in the price of wood chips. On an energy basis, the diesel fuel used directly in wood chip production and transportation appears to account for less than 2% of the potential energy in the wood chips. Thus, the dependence of woody biomass energy production on diesel fuel does not appear to be extreme. (author)

  12. Instrument for measuring moisture in wood chips

    Energy Technology Data Exchange (ETDEWEB)

    Werme, L

    1980-06-01

    A method to determine the moisture content in wood chips, in batch and on-line, has been investigated. The method can be used for frozen and non frozen chips. Samples of wood chips are thawn and dryed with microwaves. During the drying the sample is weighed continously and the rate of drying is measured. The sample is dried t 10 percent moisture content. The result is extrapolated to the drying rate zero. The acccuracy at the method is 1.6 to 1.7 percent for both frozen and non frozen chips. The accuracy of the method is considered acceptable, but sofisticated sampling equipment is necessary. This makes the method too complex to make the instrument marketable.

  13. MOISTURE HUMIDITY EQUILIBRIUM OF WOOD CHIPS FROM ENERGETIC CROPS

    Directory of Open Access Journals (Sweden)

    Jan Barwicki

    2008-09-01

    Full Text Available Processes occurring during storage of wood chips for energetic or furniture industry purposes were presented. As a result of carried out investigations, dependences of temperature and relative humidity changes of surrounding air were shown. Modified Henderson equation can be utilized for computer simulation of storing and drying processes concerning wood chips for energetic and furniture industry purposes. It reflects also obtained results from experiments carried out with above mentioned material. Using computer simulation program we can examine different wood chips storing conditions to avoid overheating and loss problems.

  14. Quality wood chips - an alternative to pellets; Alternative zu Pellets. Qualischnitzel

    Energy Technology Data Exchange (ETDEWEB)

    Keel, A.

    2008-07-01

    This article takes a look at a new wood-chip product that features wood-chips that are dryer than traditional ones. The new 'quality chips' are also of a calibrated size and are supplied dust-free. Their low water content permits their use in the same areas as wood pellets, where, especially in summer, low water-content is important. The increasing use of pellets and the growing shortages of clean sawdust and shavings for their production is commented on, as is the use of forestry wastes in pellet production. The new wood-chip product is further discussed as being a direct alternative to pellets. The low 'grey energy' content for tree-felling, hacking, transport and the drying of the chips is quoted as being less than 5% of the energy in the chippings.

  15. Organic emissions from co-combustion of RDF with wood chips and milled peat in a bubbling fluidized bed boiler

    International Nuclear Information System (INIS)

    Vesterinen, Raili; Flyktman, Martti

    1996-01-01

    Refuse derived fuel (RDF) has been burned with wood chips and milled peat in a 4 MW bubbling fluidized bed boiler. Emissions of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/F) in flue gases expressed as TCDD-equivalents were significantly below the emission limit 0.1 ng/m 3 n I-TEQ (11 % O 2 ). Also the PCDD/F-concentrations of fly ashes separated by an electrostatic precipitator are significantly below the 1 ng/g I-TEQ limit for agricultural soil in Germany. The carbon monoxide content was rather high, but typical for many small district heating plants. The concentrations of other chlorinated aromatic compounds were also low, in some tests below the detection limit. The concentrations of polyaromatic hydrocarbons (PAH) were rather high. The leachable metal content of the fly ash generated were analyzed using U.S. EPA TCLP test (Toxicity Characteristic Leaching Procedure). All concentrations fell below boundary levels. (author)

  16. Wood chip delivery and research project at Mikkeli region

    International Nuclear Information System (INIS)

    Saksa, T.; Auvinen, P.

    1995-01-01

    In 1994, a large-scale energywood production chain was started as a co-operation project by the Mikkeli city forest office and local forestry societies. Over 60 000 m 3 (about 46 000 MWh of energy) of forest processed chips were delivered to Pursiala heat and power plant in Mikkeli. About 60 % of these chips was whole tree chips from improvement cuttings of young forest stands and the rest was logging waste chips from regeneration cutting areas. The average total delivery costs of forest processed chips after reduction of energywood and other subsidies were approximately 51 FIM/m 3 (68 FIM/MWh) for the whole tree chips and 40 FIM/m 3 (53 FIM/MWh) for logging waste chips. The delivery costs of wood chips could compete with those of fuel peat only in the most favourable cases. The resources of forest processed chips were studied on the basis of forestry plans. According to the study, there is enough raw material for permanent, large-scale delivery of forest processed chips (up to 250 000 m 3 /a) in the forests located at a distance of under 40 road kilometers from the Pursiala heat and power plant. The following project stages will involve further development of the wood chip delivery chain logistics, as well as improvement of logging and chipping equipment and methods in energywood and logging waste production. Also the effects of wood energy production on the economy and environment of the whole Mikkeli region will be studied. (author)

  17. Determining wood chip size: image analysis and clustering methods

    Directory of Open Access Journals (Sweden)

    Paolo Febbi

    2013-09-01

    Full Text Available One of the standard methods for the determination of the size distribution of wood chips is the oscillating screen method (EN 15149- 1:2010. Recent literature demonstrated how image analysis could return highly accurate measure of the dimensions defined for each individual particle, and could promote a new method depending on the geometrical shape to determine the chip size in a more accurate way. A sample of wood chips (8 litres was sieved through horizontally oscillating sieves, using five different screen hole diameters (3.15, 8, 16, 45, 63 mm; the wood chips were sorted in decreasing size classes and the mass of all fractions was used to determine the size distribution of the particles. Since the chip shape and size influence the sieving results, Wang’s theory, which concerns the geometric forms, was considered. A cluster analysis on the shape descriptors (Fourier descriptors and size descriptors (area, perimeter, Feret diameters, eccentricity was applied to observe the chips distribution. The UPGMA algorithm was applied on Euclidean distance. The obtained dendrogram shows a group separation according with the original three sieving fractions. A comparison has been made between the traditional sieve and clustering results. This preliminary result shows how the image analysis-based method has a high potential for the characterization of wood chip size distribution and could be further investigated. Moreover, this method could be implemented in an online detection machine for chips size characterization. An improvement of the results is expected by using supervised multivariate methods that utilize known class memberships. The main objective of the future activities will be to shift the analysis from a 2-dimensional method to a 3- dimensional acquisition process.

  18. Wood chip production technology and costs for fuel in Namibia

    Energy Technology Data Exchange (ETDEWEB)

    Leinonen, A.

    2007-12-15

    This work has been done in the project where the main target is to evaluate the technology and economy to use bush biomass for power production in Namibia. The project has been financed by the Ministry for Foreign Affairs of Finland and the Ministry of Agriculture, Water and Forestry of the Republic of Namibia. The target of this study is to calculate the production costs of bush chips at the power plant using the current production technology and to look possibilities to develop production technology in order to mechanize production technology and to decrease the production costs. The wood production costs are used in feasibility studies, in which the technology and economy of utilization of wood chips for power generation in 5, 10 and 20 MW electric power plants and for power generation in Van Eck coal fired power plant in Windhoek are evaluated. Field tests were made at Cheetah Conservation Farm (CCF) in Otjiwarongo region. CCF is producing wood chips for briquette factory in Otjiwarongo. In the field tests it has been gathered information about this CCF semi-mechanized wood chip production technology. Also new machines for bush biomass chip production have been tested. A new mechanized production chain has been designed on the basis of this information. The production costs for the CCF semi-mechanized and the new production chain have been calculated. The target in the moisture content to produce wood chips for energy is 20 w-%. In the semi-mechanized wood chip production chain the work is done partly manually, and the supply chain is organized into crews of 4.8 men. The production chain consists of manual felling and compiling, drying, chipping with mobile chipper and manual feeding and road transport by a tractor with two trailers. The CCF production chain works well. The chipping and road transport productivity in the semimechanized production chain is low. New production machines, such as chainsaw, brush cutter, lawn mover type cutter, rotator saw in skid

  19. Production of dry wood chips in connection with a district heating plant

    Directory of Open Access Journals (Sweden)

    Yrjölä Jukka

    2004-01-01

    Full Text Available Moisture and its variation in wood chips make the control of burning in small scale heating appliances difficult resulting in emissions and loss of efficiency. If the quality of wood chips would be better, i. e. dried and sieved fuel with more uniform size distribution would be avail able, the burning could be much cleaner and efficiency higher. In addition higher power out put could be obtained and the investment costs of the burning appliances would be lower. The production of sieved and dried wood chip with good quality could be accomplished in connection with a district heating plant. Then the plant would make profit, in addition to the district heat, from the dried wood chips sold to the neighboring buildings and enterprises sep a rated from the district heating net using wood chips in energy production. The peak power of a district heating plant is required only a short time during the coldest days of the winter. Then the excess capacity during the milder days can be used as heat source for drying of wood chips to be marketed. Then wood chips are sieved and the fuel with best quality is sold and the reject is used as fuel in the plant it self. In a larger district heating plant, quality of the fuel does not need to be so high In this paper the effect of moisture on the fuel chain and on the boiler is discussed. Energy and mass balance calculations as a tool of system design is described and the characteristics of proposed dry chips production method is discussed.

  20. Multipass comminution process to produce precision wood particles of uniform size and shape with disrupted grain structure from wood chips

    Science.gov (United States)

    Dooley, James H; Lanning, David N

    2014-05-27

    A process of comminution of wood chips (C) having a grain direction to produce a mixture of wood particles (P), wherein the wood chips are characterized by an average length dimension (L.sub.C) as measured substantially parallel to the grain, an average width dimension (W.sub.C) as measured normal to L.sub.C and aligned cross grain, and an average height dimension (H.sub.C) as measured normal to W.sub.C and L.sub.C, and wherein the comminution process comprises the step of feeding the wood chips in a direction of travel substantially randomly to the grain direction one or more times through a counter rotating pair of intermeshing arrays of cutting discs (D) arrayed axially perpendicular to the direction of wood chip travel.

  1. Comminution process to produce precision wood particles of uniform size and shape with disrupted grain structure from wood chips

    Science.gov (United States)

    Dooley, James H; Lanning, David N

    2013-08-13

    A process of comminution of wood chips (C) having a grain direction to produce a mixture of wood particles (P), wherein the wood chips are characterized by an average length dimension (L.sub.C) as measured substantially parallel to the grain, an average width dimension (W.sub.C) as measured normal to L.sub.C and aligned cross grain, and an average height dimension (H.sub.C) as measured normal to W.sub.C and L.sub.C, and wherein the comminution process comprises the step of feeding the wood chips in a direction of travel substantially randomly to the grain direction through a counter rotating pair of intermeshing arrays of cutting discs (D) arrayed axially perpendicular to the direction of wood chip travel, wherein the cutting discs have a uniform thickness (T.sub.D), and wherein at least one of L.sub.C, W.sub.C, and H.sub.C is greater than T.sub.D.

  2. Methods for size classification of wood chips

    Energy Technology Data Exchange (ETDEWEB)

    Hartmann, Hans; Boehm, Thorsten [Technologie- und Foerderzentrum im Kompetenzzentrum fuer Nachwachsende Rohstoffe (TFZ), Schulgasse 18, D-94315 Straubing (Germany); Daugbjerg Jensen, Peter [Forest and Landscape FLD, The Royal Veterinary and Agricultural University, Rolighedsvej 23, DK-1958 Frederiksberg C (Denmark); Temmerman, Michaeel; Rabier, Fabienne [Centre wallon de Recherches agronomiques CRA-W Departement Genie rural, 146, Chaussee de Namur, B-5030 Gembloux (Belgium); Golser, Michael [Holzforschung Austria HFA Franz Grill-Stra beta e 7, A-1031 Wien (Austria)

    2006-11-15

    Methods for size classification of wood chips were analysed in an international round robin using 13 conventional wood chip samples and two specially prepared standard samples, one from wood chips and one from hog fuel. The true size distribution of these two samples (according to length, width and height) had been determined stereometrically (reference method) using a digital calliper gauge and by weighing each of the about 7000 wood particles per sample. Five different horizontal and three rotary screening devices were tested using five different screen hole diameters (3.15, 8, 16, 45, 63mm, round holes). These systems are compared to a commercially available continuously measuring image analysis equipment. The results show that among the devices of a measuring principle-horizontal and rotary screening-the results are quite comparable, while there is a severe incompatibility when distributions are determined by different measuring principles. Highest conformity with the reference values is given for measurements with an image analysis system, whereas for all machines with horizontal screens the median value of the size distribution only reached between one-third to half of the reference median value for the particle length distribution. These deviations can be attributed to a higher particle misplacement, which is particularly found in the larger fractions. Such differences decrease when the particle's shape is more roundish (i.e. sphericity closer to one). The median values of length distributions from screenings with a rotary classifier are between the measurements from an image analysis and horizontal screening devices. (author)

  3. Toxicity of invert drilling muds composted with wood/bark chips

    Energy Technology Data Exchange (ETDEWEB)

    Bessie, K. [EBA Engineering Consultants Ltd., Calgary, AB (Canada)

    2006-07-01

    Since the early to mid 1990s, many companies have composted invert (diesel) drilling muds with wood chips/bark chips in the green (forestry) zone as a method of drilling mud treatment. This presentation addressed the toxicity of invert drilling muds composted with wood/bark chips and provided some background on composted invert drilling mud (CIDM). EBA Engineering monitored 22 third-party sites in 2002, some of which were biopiles, and others land treatment areas (LTAs). Active treatment started between 1995 and 1999 and some LTAs were seeded with varying degrees of success. Composted materials had hydrocarbon odour and staining and were very moist. Materials exceeded Alberta Environment guidelines for petroleum hydrocarbons (PHCs) and sometimes barium. Most sites were within areas that had forestry production/wildlife as end land use. Receptors included plants, soil invertebrates by soil contact, and wildlife by ingestion. Stakeholder meetings were held for their input and an ecotoxicity study was developed. Material tested, tests and species used as well as results of the ecotoxicity study were presented. A comparison of results to other EBA composting studies was also given. It was concluded that CIDM affects the reproduction of earthworms and springtails, and plant growth; wood/barks chips themselves can be ecotoxic; and, other compost studies with finely ground sawdust and no bark chips had less ecotoxicity. tabs., figs.

  4. Characteristics of wood chip fuel demand and supply in south-west Japan

    Energy Technology Data Exchange (ETDEWEB)

    Teraoka, Y.; Sato, M.; Ijichi, S. [Faculty of Agriculture, Kagoshima Univ., Kagoshima (Japan)

    2012-11-01

    Although fossil fuel has been still important energy source in Japan, business managers who examine to sift energy source from oil to bio-fuels would increase for reducing CO{sub 2} emission and high energy cost. It would be quite reasonable choice for Japanese people to use woody biomass for energy sources but woody biomass fuel market hasn't been expanded. One of the reasons is that the Japanese timber production, processing and distribution sectors haven't considered the wood fuel production as by-product. Therefore, this study investigated a potential wood chip boiler demand in south-west Japan through a questionnaire survey for industrial sectors. Second aim is to explain the importance of management information such as a quantity of chip fuel production or distribution and a moisture content of chips from the example cases of installed chip boiler facilities. Expected facilities that would introduce a chip boiler are a hotel, a large hospital, a liquor factory and an aquaculture pool. There will be an annual wood chip fuel demand of 0.756 million green-ton (6.0 PJ) in Kagoshima Prefecture. Problems in more chip boilers introduction are a stable fuel supply and fuel moisture control in addition to the reduction of an initial and operational running cost.

  5. Linear equations on thermal degradation products of wood chips in alkaline glycerol

    International Nuclear Information System (INIS)

    Demirbas, Ayhan

    2004-01-01

    Wood chips of 0.3 and 2 mm depth from poplar and spruce wood samples, respectively, were degraded by using glycerol as a solvent and alkaline glycerol with and without Na 2 CO 3 and NaOH catalysts at different degradation temperatures: 440, 450, 460, 470, 480, 490 and 500 K. By products from the degradation processes of the ligno celluloses include lignin degradation products. Lignin and its degradation products have fuel values. The total degradation degree and cellulose degradation of the wood chips were determined to find the relationship, if any, between the yields of total degradation degree (YTD) and degradation temperature (T). There is a good linear relationship between YTD or the yields of cellulose degradation (YCD) and T (K). For the wood samples, the regression equations from NaOH (10%) catalytic runs for 0.3 mm x 15 mm x 15 mm chip size are: For poplar wood: (YTD=0.7250T-267.507) (YCD=0.1736T-71.707) For spruce wood: (YTD=0.2650T-105.979) (YCD=0.0707T-27.507) For Eqs., the square of the correlation coefficient (r 2 ) were 0.9841, 0.9496, 0.9839 and 0.9447, respectively

  6. Ashes from straw and wood-chip fired plants for agricultural usage. Pilot project

    International Nuclear Information System (INIS)

    Morsing, M.; Westborg, S.

    1994-08-01

    The content of nutrients and heavy metals in ashes from the combustion of straw and wood chips at district heating plants is studied, on the basis of results of analyses from Danish municipalities, to determine whether such ashes are suitable for use as fertilizers. Results of the analysis of ashes from 9 wood-chip fired and 26 straw-fired plants are presented. They show significant variations in nutrient and heavy metal content which could be caused by combustion and operational conditions and/or testing methods. On condition that the phosphorous content of straw and wood-chip ashes amount to 1% of the dry matter, 50%-75% of the straw ashes and under 50% of wood chip ashes analyses are within the limit for cadmium stipulated in the Danish Ministry of the Environment's Executive Order no. 736 on the use of wastes for agricultural purposes. This is found to be unsatisfactory. It is suggested that a closer investigation should be undertaken in order to determine which amount of straw and wood-chip ashes can be accepted for use as fertilizers in consideration of the stipulated limits for cadmium content of wastes to be used for agricultural purposes. In addition the technological and economic potentials of dosing of these ashes for this use should be investigated. Fly ash and slag were also included in the analysis results studied and it was found that the cadmium content of slag did not prevent its use as fertilizer, but that the distribution of cadmium in slag, in fly ash and in slam from flue gas cleaning systems related to the combustion of wood chips should be further investigated. (AB)

  7. Successful experience with limestone and other sorbents for combustion of biomass in fluid bed power boilers

    Energy Technology Data Exchange (ETDEWEB)

    Coe, D.R. [LG& E Power Systems, Inc., Irvine, CA (United States)

    1993-12-31

    This paper presents the theoretical and practical advantages of utilizing limestone and other sorbents during the combustion of various biomass fuels for the reduction of corrosion and erosion of boiler fireside tubing and refractory. Successful experiences using a small amount of limestone, dolomite, kaolin, or custom blends of aluminum and magnesium compounds in fluid bed boilers fired with biomass fuels will be discussed. Electric power boiler firing experience includes bubbling bed boilers as well as circulating fluid bed boilers in commercial service on biomass fuels. Forest sources of biomass fuels fired include wood chips, brush chips, sawmill waste wood, bark, and hog fuel. Agricultural sources of biomass fuels fired include grape vine prunings, bean straw, almond tree chips, walnut tree chips, and a variety of other agricultural waste fuels. Additionally, some urban sources of wood fuels have been commercially burned with the addition of limestone. Data presented includes qualitative and quantitative analyses of fuel, sorbent, and ash.

  8. Microfungi problem, health aspects. [Storage of wood fuel chips

    Energy Technology Data Exchange (ETDEWEB)

    Jirjis, Raida (Swedish Univ. of Agricultural Sciences, Uppsala (SE). Dept. of Forest Products)

    1988-11-01

    The storage of wood fuel chips, in general, leads to the establishment of microbial activity in the pile. Fungi are one of these microorganisms which can grow vigorously in stored forest products. Different types of fungi are commonly present on wood chip pile; rot fungi, blue stain fungi and moulds. Each fungis has its optimum temperature and humidity. Fungi also differ in their ability to utilize different components of the biofuel; moulds are unable to degrade lignin and only few species can degrade cellulose. Rot fungi on the other hand can attack all parts of the substrate and degrade it to varying degrees. Sporulation in fungi is their mechanisms for reproduction and survival. The spores are produced asexually in special spore carriers which are specific for each type of fungi. In stored wood chip pile the sporulation of moulds is the source of health hazard due to its ability to produce very large numbers of microspores in a short period. These microspores are usually airborne and they are almost always present in air but their numbers differ with time, weather and location. Most people can tolerate the presence of these microfungi at concentrations up to 10{sup 6} spore/m{sup 3} air, but a more intense exposure of 10{sup 10} spores/m{sup 3} air con provoke allergic reactions in certain individuals causing allergic alveolitis. The growth of different fungi on stored wood chips pile depends on the time and the system of storage that is used for that pile. In general, indoors storage, high moisture contents and excess of fine fractions are factors that could lead to intensive fungal activity. Handling of such material necessitate the use of protective helmet to avoid the risks of allergic reactions. (4 refs.) (au).

  9. Dissipation of atrazine, enrofloxacin, and sulfamethazine in wood chip bioreactors and impact on denitrification

    Science.gov (United States)

    Wood chip bioreactors are receiving increasing attention as a means of reducing nitrate in subsurface tile drainage systems. Agrochemicals in tile drainage water entering wood chip bioreactors can be retained or degraded and may impact denitrification. The degradation of 5 mg L-1 atrazine, enrofloxa...

  10. Investigating Potential Toxicity of Leachate from Wood Chip Piles Generated by Roadside Biomass Operations

    Directory of Open Access Journals (Sweden)

    John Rex

    2016-02-01

    Full Text Available Roadside processing of wood biomass leaves chip piles of varying size depending upon whether they were created for temporary storage, spillage, or equipment maintenance. Wood chips left in these piles can generate leachate that contaminates streams when processing sites are connected to waterways. Leachate toxicity and chemistry were assessed for pure aspen (Populus tremuloides Michx., lodgepole pine (Pinus contorta Dougl., hybrid white spruce (Picea engelmannii x glauca Parry, and black spruce (Picea mariana (Mill. Britton as well as from two wood chipping sites using mixes of lodgepole pine and hybrid or black spruce. Leachate was generated using rainfall simulation, a static 28-day laboratory assay, and a field-based exposure. Leachate generated by these exposures was analyzed for organic matter content, phenols, ammonia, pH, and toxicity. Findings indicate that all wood chip types produced a toxic leachate despite differences in their chemistry. The consistent toxicity response highlights the need for runoff management that will disconnect processing sites from aquatic environments.

  11. Developing technology for large-scale production of forest chips. Wood Energy Technology Programme 1999-2003. Interim report

    International Nuclear Information System (INIS)

    Hakkila, P.

    2003-01-01

    2002, the programme consisted of 35 research projects, 35 industry projects and 15 demonstration projects, inclusive of the completed ones. The participation of researchers and practitioners in joint projects has strengthened the research capacity and promoted networking amongst research organizations in the field of wood energy in Finland. Furthermore, researchers have been able to identify and meet the practical needs of the industry, and joint projects have facilitated the dissemination of research results to practical forestry, forest industry, energy enterprises and machine manufacturers. During the first three years of the five-year programme, the use of forest chips increased from 0.5 Mm' to 1.3 Mm'. The average increase was thus 270 000 m' per annum. If the official goal of the Action Plan for Renewable Energy Sources is to be achieved, an increase of 400 000 m' is required in each year of this decade. The biomass resource exists. The combustion capacity of the present and planned heating and power plants is sufficient to absorb practically all competitively priced woody biomass available. As a result of the recent technological development, even stump and root wood can be used by large power plants equipped with modern fluidized bed technology. Considerable progress is taking place in the technology of chip production, e.g. the successful CRL system based on bundling of residues and crushing at the plant. Nevertheless, the production of chips rather than combustion technology still remains the real bottleneck for the utilization of the biomass potential of the Finnish forests. The main barrier is the high price of chips. Even worse, the fall in costs of production in the 1990s is supposed to reverse. Consequently, it is of great importance that the support for the research, development and commercialization of forest chip production technology should continue after the Wood Energy Technology Programme ends in 2003. For example, Tekes has recently expanded the

  12. Wood chips procurement and research project at the Mikkeli region

    International Nuclear Information System (INIS)

    Saksa, T.; Auvinen, P.

    1996-01-01

    In 1993-94, a large-scale energywood production chain started as a co-operation project by the Mikkeli city forest office and local forestry societies. In 1995 over 115 000 m 3 (about 85 000 MWh of energy) of wood chips were delivered to Pursiala heat and power plant in Mikkeli. About 75 % of these chips was forest processed chips. About 70 % of the forest processed chips was whole tree chips from improvement cuttings of young forest stands and the rest was logging waste chips from regeneration cutting areas. The average total delivery costs of forest processed chips after reduction of energywood and other subsidies were approximately 45 FIM/m 3 (60 FIM/MWh) for the whole tree chips and 38 FIM/m 3 (50 FIM/MWh) for logging waste chips. The delivery costs of forest processed chips could meet the target of Bioenergy Research Programme (45 FIM/MWh) only in the most favourable cases. In an average the delivery costs were about 9 FIM/MWh more than the price obtained when sold to the heat and power plant. However the wood chip production created 27 new jobs and the increase of income to the local economy was about 2.2 milj. FIM /year. The local communities got new tax revenue about 3 FIM/MWh. The gain for the forestry was approximated to be 5 - 6 FIM/MWh. The resources of forest processed chips were studied on the basis of stand measurements. According to the study the most remarkable energywood resources were in young thinning stands on Oxalis-Myrtillus and Myrtillus forest site types. On Oxalis-Myrtillus type almost every and on Myrtillus type every second stand included energywood more than 40 m 3 /ha

  13. Quaternized wood as sorbent for hexavalent chromium.

    Science.gov (United States)

    Low, K S; Lee, C K; Lee, C Y

    2001-01-01

    The potential of quaternized wood (QW) chips in removing hexavalent chromium from synthetic solution and chrome waste under both batch and continuous-flow conditions was investigated. Sorption was found to be dependent on pH, metal concentration, and temperature. QW chips provide higher sorption capacity and wider pH range compared with untreated wood chips. The equilibrium data could be fitted into the Langmuir isotherm model, and maximum sorption capacities were calculated to be 27.03 and 25.77 mg/g in synthetic chromate solution and chrome waste, respectively. The presence of sulfate in high concentration appeared to suppress the uptake of chromium by QW chips. Column studies showed that bed depth influenced the breakthrough time greatly whereas flow rate of influent had little effect on its sorption on the column.

  14. Effect of chipping on emergence of the redbay ambrosia beetle (Coleoptera: Curculionidae: Scolytinae) and recovery of the laurel wilt pathogen from infested wood chips.

    Science.gov (United States)

    Spence, D J; Smith, J A; Ploetz, R; Hulcr, J; Stelinski, L L

    2013-10-01

    Significant mortality ofredbay trees (Persea borbonia (L.) Spreng.) in the southeastern United States has been caused by Raffaelea lauricola, T.C. Harr., Fraedrich, & Aghayeva (Harrington et al. 2008), a fungal symbiont of the exotic redbay ambrosia beetle, Xyleborus glabratus, Eichhoff (Fraedrich et al. 2008). This pathogen causes laurel wilt, which is an irreversible disease that can kill mature trees within a few weeks in summer. R. lauricola has been shown to be lethal to most native species of Lauraceae and cultivated avocado (Persea americana Mill.) in the southeastern United States. In this study, we examined the survival of X. glabratus and R. lauricola in wood chips made from infested trees by using a standard tree chipper over a 10-wk period. After 2 wk, 14 X. glabratus were recovered from wood chips, whereas 339 X. glabratus emerged from nonchipped bolts. R. lauricola was not found 2 d postchipping from wood chips, indicating that the pathogen is not likely to survive for long inside wood chips. In contrast, R. lauricola persisted in dead, standing redbay trees for 14 mo. With large volumes of wood, the potential for infested logs to be moved between states or across U.S. borders is significant. Results demonstrated that chipping wood from laurel wilt-killed trees can significantly reduce the number of X. glabratus and limit the persistence of R. lauricola, which is important for sanitation strategies aimed at limiting the spread of this disease.

  15. Gasification of wood in a fluidized bed reactor

    Energy Technology Data Exchange (ETDEWEB)

    Sousa, L.C. de; Marti, T; Frankenhaeuser, M [Paul Scherrer Inst. (PSI), Villigen (Switzerland)

    1997-06-01

    A first series of gasification experiments with our fluidized bed gasifier was performed using clean sawdust as fuel. The installation and the analytical systems were tested in a parametric study in which gasification temperature and equivalence ratio were varied. The data acquired will serve to establish the differences between the gasification of clean wood and the gasification of Altholz (scrapwood) and wood/plastics mixtures. (author) 1 fig., 3 tabs., 5 refs.

  16. Geographical analyses of wood chips potentials, cost and supply for sustainable energy production in Denmark

    DEFF Research Database (Denmark)

    Möller, Bernd

    2004-01-01

    The paper presents a study which uses a practical application of rasterbased geographical information system to perform cost-supply analysis of wood chips resources for energy production.......The paper presents a study which uses a practical application of rasterbased geographical information system to perform cost-supply analysis of wood chips resources for energy production....

  17. Low temperature fluidized wood chip drying with monoterpene analysis

    Science.gov (United States)

    Bridget N. Bero; Alarick Reiboldt; Ward Davis; Natalie Bedard; Evan Russell

    2011-01-01

    This paper describes the drying of ponderosa pine wood chips at low (20°C and 50°C) temperatures using a bench-scale batch pulsed fluidizer to evaluate both volatile pine oils (monoterpenes) and moisture losses during drying.

  18. Airtight storage of wood chips for use as a fuel

    Energy Technology Data Exchange (ETDEWEB)

    Lamond, W.J.; Graham, R.; Boyd, J.E.L.; Harling, R.; Lowe, J.F.

    1993-11-01

    This study was carried out to see if airtight storage was a possible alternative to drying as a procedure for the successful storage of chipped wood for fuel. Twelve insulated bins, with a capacity of approximately 0.1 m{sup 3} each, were filled with freshly cut Sitka Spruce wood chips. Ten of these bins were sealed immediately after filling and the remaining two left unsealed for the duration of the experiment (12 months). The programme of sampling for gas, moisture content, mycology and bacteriology is described. The results showed that sealed storage reduced the overall dry matter loss in the bins to around 1% per month compared to 2% for the unsealed bins. This compares favourably with losses of around 3% per month which have been reported for open stacks of chips with much lower initial moisture contents than that used in these experiments. There was a slight reduction in the colorific value of oven dried chips between the initial and after storage samples. The moisture content of the chips in all the bins increased over the storage period. The average energy loss was 2.9% per month for sealed and 2.0% per month for unsealed treatment. A typical ecological succession was shown by the chips, commencing with field fungi and terminating with a dominant yeast population. Potential costs for suitable stores vary from Pounds 1.27 per m{sup 3} per year for a plastic covered outdoor stack to Pounds 11.72 per m{sup 3} per year for a vitreous enamel silo. (UK)

  19. Intracage ammonia levels in static and individually ventilated cages housing C57BL/6 mice on 4 bedding substrates.

    Science.gov (United States)

    Ferrecchia, Christie E; Jensen, Kelly; Van Andel, Roger

    2014-03-01

    The relationship among ammonia levels, cage-changing frequency, and bedding types is an important and potentially controversial topic in the laboratory animal science community. Some bedding options may not provide sufficient urine absorption and bacterial regulation to minimize ammonia production during the interval between cage changes. High intracage ammonia levels can cause subclinical degeneration and inflammation of nasal passages, rhinitis and olfactory epithelial necrosis in exposed mice. Here we sought to compare the effects of 4 commonly used bedding substrates (1/4-in. irradiated corncob, reclaimed wood pulp, aspen wood chips, and recycled newspaper) on ammonia generation when housing female C57BL/6 mice in static and individually ventilated caging. Intracage ammonia levels were measured daily for 1 wk (static cage experiment) or 2 wk (IVC experiment). The results of this study suggest that the corncob, aspen wood chip, and recycled newspaper beddings that we tested are suitable for once-weekly cage changing for static cages and for changing every 2 wk for IVC. However, ammonia levels were not controlled appropriately in cages containing reclaimed wood pulp bedding, and pathologic changes occurred within 1 wk in the nares of mice housed on this bedding in static cages.

  20. Bed agglomeration in fluidized combustor fueled by wood and rice straw blends

    DEFF Research Database (Denmark)

    Thy, Peter; Jenkins, Brian; Williams, R.B.

    2010-01-01

    Abstract Petrographic techniques have been used to examine bed materials from fluidized bed combustion experiments that utilized wood and rice straw fuel blends. The experiments were conducted using a laboratory-scale combustor with mullite sand beds, firing temperatures of 840 to 1030 °C, and ru...

  1. Bed agglomeration in fluidized combustor fueled by wood and rice straw blends

    NARCIS (Netherlands)

    Thy, P.; Jenkins, B.M.; Williams, R.B.; Lesher, C.E.; Bakker, R.R.

    2010-01-01

    Petrographic techniques have been used to examine bed materials from fluidized bed combustion experiments that utilized wood and rice straw fuel blends. The experiments were conducted using a laboratory-scale combustor with mullite sand beds, firing temperatures of 840 to 1030 °C, and run durations

  2. Influence of various alternative bedding materials on pododermatitis in broilers raised in a built-up litter system

    Science.gov (United States)

    Broilers in the United States are frequently raised on built-up litter systems, primarily bedded with pine wood chips (shavings) or sawdust. There is continuing interest in alternative bedding materials as pine products are often in short supply and prices rise accordingly. Alternative bedding mat...

  3. Kinetic model for torrefaction of wood chips in a pilot-scale continuous reactor

    DEFF Research Database (Denmark)

    Shang, Lei; Ahrenfeldt, Jesper; Holm, Jens Kai

    2014-01-01

    accordance with the model data. In an additional step a continuous, pilot scale reactor was built to produce torrefied wood chips in large quantities. The "two-step reaction in series" model was applied to predict the mass yield of the torrefaction reaction. Parameters used for the calculation were...... at different torrefaction temperatures, it was possible to predict the HHV of torrefied wood chips from the pilot reactor. The results from this study and the presented modeling approach can be used to predict the product quality from pilot scale torrefaction reactors based on small scale experiments and could...

  4. Wood-plastic composites using thermomechanical pulp made from oxalic acid-pretreated red pine chips

    Science.gov (United States)

    J.E. Winandy; N.M. Stark; E. Horn

    2008-01-01

    The characteristics and properties of wood fiber is one of many factors of critical importance to the performance of wood-plastic composites. In commercial thermo-mechanical pulping (TMP) of wood chips to produce fibers, high temperatures (>100°C) are used to separate the fibers during TMP refining. These mechanical pressures and temperatures are usually modulated...

  5. UNMANNED AERIAL VEHICLE USE FOR WOOD CHIPS PILE VOLUME ESTIMATION

    Directory of Open Access Journals (Sweden)

    M. Mokroš

    2016-06-01

    Full Text Available The rapid development of unmanned aerial vehicles is a challenge for applied research. Many technologies are developed and then researcher are looking up for their application in different sectors. Therefore, we decided to verify the use of the unmanned aerial vehicle for wood chips pile monitoring. We compared the use of GNSS device and unmanned aerial vehicle for volume estimation of four wood chips piles. We used DJI Phantom 3 Professional with the built-in camera and GNSS device (geoexplorer 6000. We used Agisoft photoscan for processing photos and ArcGIS for processing points. Volumes calculated from pictures were not statistically significantly different from amounts calculated from GNSS data and high correlation between them was found (p = 0.9993. We conclude that the use of unmanned aerial vehicle instead of the GNSS device does not lead to significantly different results. Tthe data collection consumed from almost 12 to 20 times less time with the use of UAV. Additionally, UAV provides documentation trough orthomosaic.

  6. Bed agglomeration in fluidized combustor fueled by wood and rice straw blends

    DEFF Research Database (Denmark)

    Thy, Peter; Jenkins, Brian; Williams, R.B.

    2010-01-01

    Abstract Petrographic techniques have been used to examine bed materials from fluidized bed combustion experiments that utilized wood and rice straw fuel blends. The experiments were conducted using a laboratory-scale combustor with mullite sand beds, firing temperatures of 840 to 1030 °C, and run...... areas between bed particles, ultimately led to bed agglomeration. The interfaces and the presence of gas bubbles in the cement suggest a bonding material with a high surface tension and a liquid state. The cement films originate by filling of irregularities on individual and partially agglomerated bed...

  7. Combustion in fluidized bed reactors; Verbrennung in Wirbelschichtreaktoren

    Energy Technology Data Exchange (ETDEWEB)

    Thome-Kozmiensky, Karl J. [vivis CONSULT GmbH, Nietwerder (Germany)

    2013-03-01

    Since the first application for the coal gasification, the fluidized bed technology has passed an impressive development. Nowadays, the fluidized bed technology is utilized at chemical processes, drying and cooling, gasification, combustion and purification of exhaust gas. In the firing technology, the fluidized technology initially has been proved in the combustion of very high ash coal and sewage sludge. Recently, the fluidized bed technology also is applied in the drying of sewage sludge, combustion of domestic waste - as in Japan and Sweden - as well as in the gasification and combustion of substitute fuels, biomass - wood pellets, wood chips, straw, cocoa shells and so forth - and residues from the paper manufacturing - such as in Germany and Austria. Under this aspect, the author of the contribution under consideration reports on the combustion of sewage sludge, substitute fuels and biomass.

  8. First Nation partner in wood-chip cogen project

    International Nuclear Information System (INIS)

    O'Gorman, P.

    1996-01-01

    The Ginoogaming First Nation is working with Long Lake Forest Products to develop a cogeneration plant at a local mill which would burn wood chips and waste wood to produce heat and electrical energy for the mill and the community. The plan is part of a larger development project by the community that calls for the construction of new infrastructure, services and business for the town of 250 people near Thunder Bay, Ontario. It is a widely held view that energy is a major factor in achieving self reliance for First Nations especially in remote communities. Concern was expressed by Ontario Hydro that if the town takes over its own electricity production, Ontario Hydro may still be legally required to maintain back up generation. The preferred remedy would be to lift Ontario Hydro's obligation to provide all power to remote communities of Ontario

  9. Universal characteristics of particle shape evolution by bed-load chipping

    Science.gov (United States)

    Sipos, András Árpád; Shaw, Sam; Sarti, Giovanni; Domokos, Gábor

    2018-01-01

    River currents, wind, and waves drive bed-load transport, in which sediment particles collide with each other and Earth’s surface. A generic consequence is impact attrition and rounding of particles as a result of chipping, often referred to in geological literature as abrasion. Recent studies have shown that the rounding of river pebbles can be modeled as diffusion of surface curvature, indicating that geometric aspects of impact attrition are insensitive to details of collisions and material properties. We present data from fluvial, aeolian, and coastal environments and laboratory experiments that suggest a common relation between circularity and mass attrition for particles transported as bed load. Theory and simulations demonstrate that universal characteristics of shape evolution arise because of three constraints: (i) Initial particles are mildly elongated fragments, (ii) particles collide with similarly-sized particles or the bed, and (iii) collision energy is small enough that chipping dominates over fragmentation but large enough that sliding friction is negligible. We show that bed-load transport selects these constraints, providing the foundation to estimate a particle’s attrition rate from its shape alone in most sedimentary environments. These findings may be used to determine the contribution of attrition to downstream fining in rivers and deserts and to infer transport conditions using only images of sediment grains. PMID:29670937

  10. Characterization of volatile constituents in commercial oak wood chips.

    Science.gov (United States)

    Fernández de Simón, Brígida; Muiño, Iria; Cadahía, Estrella

    2010-09-08

    The volatile composition of the different oak wood pieces (chips of Quercus spp.) that can be found on the market to be used as alternatives to barrels for aging wines, as well as of chips of Quercus pyrenaica which are being introduced, was studied, evaluating the contents of volatile phenols, lactones, furanic compounds, pyranones, phenolic aldehydes, phenolic ketones, and others. In regard to the overall results, the volatile composition of these products varies widely and has not been clearly laid out according to either the oak species or the wood toasting intensity. Taking into account that the different characteristics of alternatives to barrel products are reflected in the wine treated with them and that an oenological profile based on these variables (origin and toasting level) cannot be defined, only an appropriate chemical analysis would reveal the quality of alternative-to-barrel products and allow us to attempt to foresee its effects on the chemical and organoleptic characteristics of the wines treated with them. On the other hand, the Q. pyrenaica alternative products are very similar to those of other species, with some aromatic particularities, such as their high levels of furanic compounds, eugenol, Furaneol, and cis-whiskylactone, and low levels of vanillin.

  11. Logistics of in-wood chipping and trucking of chips; Palstahaketuksen logistinen ketju

    Energy Technology Data Exchange (ETDEWEB)

    Nuuja, J [Joensuu Univ. (Finland). Faculty of Forestry; Asikainen, A [Metsaeosaamiskeskus, Joensuu (Finland). Joensuu Science Park

    1997-12-31

    In this study a in wood chipper and truck transport of chips were modelled and studied by discrete-event simulation. The input data, which included stand characteristics and information about transport distances was compiled by GRASS-program. This data based on the inventory done by Forestry Center TAPIO. With the model various transport alternatives were compared and the effect of work condition factors were studied. It was find out, that a long distance transport with interchangeable container truck gives better productivity than a truck with a trailer. This results from shorter loading time for the interchangeable container truck

  12. Logistics of in-wood chipping and trucking of chips; Palstahaketuksen logistinen ketju

    Energy Technology Data Exchange (ETDEWEB)

    Nuuja, J. [Joensuu Univ. (Finland). Faculty of Forestry; Asikainen, A. [Metsaeosaamiskeskus, Joensuu (Finland). Joensuu Science Park

    1996-12-31

    In this study a in wood chipper and truck transport of chips were modelled and studied by discrete-event simulation. The input data, which included stand characteristics and information about transport distances was compiled by GRASS-program. This data based on the inventory done by Forestry Center TAPIO. With the model various transport alternatives were compared and the effect of work condition factors were studied. It was find out, that a long distance transport with interchangeable container truck gives better productivity than a truck with a trailer. This results from shorter loading time for the interchangeable container truck

  13. A moving-bed gasifier with internal recycle of pyrolysis gas

    NARCIS (Netherlands)

    Susanto, H.; Beenackers, A.A C M

    A co-current moving bed gasifier with internal recycle and separate combustion of pyrolysis gas has been developed with the aim of producing a design suitable for scaling-up downdraft gasifiers while maintaining a low tar content in the producer gas. Using wood chips with a moisture content of 7-9

  14. Flexible production and logistics of wood chips; Joustava hakkeen valmistus ja logistiikka

    Energy Technology Data Exchange (ETDEWEB)

    Haemaelaeinen, M; Pankakari, P [Metsaeenergia Meter Ky, Louhi (Finland)

    1997-12-31

    The target of the project was to develop a multi-purpose chipper-lorry (MOHA), which could be used both as chipping and transportation unit. MOHA is capable of chipping trees directly from the lot, so the size of the storage plays no role. Even though the MOHA-unit can be used as an individual transportation unit, it can also be used for feeding any further dispatch unit equipped with interchangeable container system e.g. when the transportation distances are long and the ordered volumes of wood chips are large. Previous projects concerning chipping-logistics are based on various intermediate storage models, but the MOHA delivers the chips strait from the lot to the site of utilization. The raw material short-distance haulage is reduced from previous 150 - 250 m to 1 - 50 m. In this new delivery model chips are bunkered only at largest heating plants. At smaller heating plants no bunker storages are needed. MOHA collects self the load, delivers it, brings, if controlled properly, back-haul, and delivers it to another site of utilization

  15. Flexible production and logistics of wood chips; Joustava hakkeen valmistus ja logistiikka

    Energy Technology Data Exchange (ETDEWEB)

    Haemaelaeinen, M.; Pankakari, P. [Metsaeenergia Meter Ky, Louhi (Finland)

    1996-12-31

    The target of the project was to develop a multi-purpose chipper-lorry (MOHA), which could be used both as chipping and transportation unit. MOHA is capable of chipping trees directly from the lot, so the size of the storage plays no role. Even though the MOHA-unit can be used as an individual transportation unit, it can also be used for feeding any further dispatch unit equipped with interchangeable container system e.g. when the transportation distances are long and the ordered volumes of wood chips are large. Previous projects concerning chipping-logistics are based on various intermediate storage models, but the MOHA delivers the chips strait from the lot to the site of utilization. The raw material short-distance haulage is reduced from previous 150 - 250 m to 1 - 50 m. In this new delivery model chips are bunkered only at largest heating plants. At smaller heating plants no bunker storages are needed. MOHA collects self the load, delivers it, brings, if controlled properly, back-haul, and delivers it to another site of utilization

  16. Addition of wood chips in red wine during and after alcoholic fermentation: differences in color parameters, phenolic content and volatile composition

    Directory of Open Access Journals (Sweden)

    Maria Kyraleou

    2016-12-01

    Full Text Available The effect of the time of wood chip addition on phenolic content, color parameters and volatile composition of a red wine made by a native Greek variety (Agiorgitiko was evaluated. For this purpose, chips from American, French, Slavonia oak and Acacia were added in the wine during and after fermentation. Various chemical parameters of wines were studied after one, two and three months of contact with chips. The results showed that the addition of oak chips during alcoholic fermentation did not favor ellagitannin extraction and the reactions involved in tannin condensation and anthocyanin stabilization. Moreover, wines fermented with wood chips contained higher contents of whiskey lactones, eugenol, ethyl vanillate and acetate esters while their ethyl ester content was lower compared with the wines where chip addition took place after fermentation. Practical Application: The outcomes of this study would be of practical interest to winemakers since they could improve the control over the wood extraction process. When chips are added after fermentation wines seem to have a greater ageing potential compared to the wines fermented with chips due to their higher ellagitannin content and enhanced condensation reactions. On the other hand, color stabilization and tannin polymerization occur faster when chips are added during fermentation resulting in shorter ageing periods suitable for early consumed wines.

  17. Numerical analysis of the interaction between high-pressure resin spray and wood chips in a vapour stream

    Directory of Open Access Journals (Sweden)

    Massimo Milani

    2016-04-01

    Full Text Available This article investigates the interaction between the resin spray and the wood chips in a vapour stream using a multi-phase multi-component computational fluid dynamics approach. The interaction between the spray and the chips is one of the main issues in the industrial process for manufacturing medium density fibre boards. Thus, the optimization of this process can lead to important benefits, such as the reduction in the emission of formaldehyde-based toxic chemicals, the reduction in energy consumption in the blending process and energy saving in the fibreboard drying process. First step of the study is the numerical analysis of the resin injector in order to extend the experimental measurements carried out with water to the resin spray. The effects of the injector’s geometrical features on the spray formation are highlighted under different injection pressure values and needle displacements. Afterwards, the results obtained in the analysis of the single injector are used for the complete simulation of multi-injector rail where the mixing of the resin spray and wood chips takes place. The influence of the main operating conditions, such as the vapour and the wood chip flow rates, on the resin distribution is addressed in order to optimize the resination process.

  18. An Investigation on the Efficiency of Air Purification Using a Biofilter with Activated Bed of Different Origin

    Directory of Open Access Journals (Sweden)

    Zagorskis Alvydas

    2014-12-01

    Full Text Available Recent studies in the area of biological air treatment in filters have addressed fundamental key issues, such as a biofilter bed of different origin composed of natural zeolite granules, foam cubes and wood chips. When foam and zeolite are mixed with wood chips to remove volatile organic compounds from the air, not only biological but also adsorption air purification methods are accomplished. The use of complex purification technologies helps to improve the efficiency of a filter as well as the bed service life of the filter bed. Investigations revealed that microorganisms prevailing in biological purification, can also reproduce themselves in biofilter beds of inorganic and synthetic origin composed of natural zeolite and foam. By cultivating associations of spontaneous microorganisms in the filter bed the dependencies of the purification efficiency of filter on the origin, concentration and filtration time of injected pollutants were determined. The highest purification efficiency was obtained when air polluted with acetone vapour was supplied to the equipment at 0.1 m/s of superficial gas velocity. When cleaning air from volatile organic compounds (acetone, toluene and butanol, under the initial pollutant concentration of ~100 mg/m3, the filter efficiency reached 95 %.

  19. Wood chips procurement and research project at the Mikkeli region; Puuhakkeen hankinta- ja tutkimusprojekti Mikkelin seudulla

    Energy Technology Data Exchange (ETDEWEB)

    Saksa, T [Finnish Forest Research Inst., Suonenjoki (Finland). Suonenjoki Research Station; Auvinen, P [Mikkeli city (Finland). Dept. of Agriculture and Forestry

    1997-12-31

    In 1993-94, a large-scale energywood production chain started as a co-operation project by the Mikkeli city forest office and local forestry societies. In 1995 over 115 000 m{sup 3} (about 85 000 MWh of energy) of wood chips were delivered to Pursiala heat and power plant in Mikkeli. About 75 % of these chips was forest processed chips. About 70 % of the forest processed chips was whole tree chips from improvement cuttings of young forest stands and the rest was logging waste chips from regeneration cutting areas. The average total delivery costs of forest processed chips after reduction of energywood and other subsidies were approximately 45 FIM/m{sup 3} (60 FIM/MWh) for the whole tree chips and 38 FIM/m{sup 3} (50 FIM/MWh) for logging waste chips. The delivery costs of forest processed chips could meet the target of Bioenergy Research Programme (45 FIM/MWh) only in the most favourable cases. In an average the delivery costs were about 9 FIM/MWh more than the price obtained when sold to the heat and power plant. However the wood chip production created 27 new jobs and the increase of income to the local economy was about 2.2 milj. FIM /year. The local communities got new tax revenue about 3 FIM/MWh. The gain for the forestry was approximated to be 5 - 6 FIM/MWh. The resources of forest processed chips were studied on the basis of stand measurements. According to the study the most remarkable energywood resources were in young thinning stands on Oxalis-Myrtillus and Myrtillus forest site types. On Oxalis-Myrtillus type almost every and on Myrtillus type every second stand included energywood more than 40 m{sup 3}/ha

  20. Wood chips procurement and research project at the Mikkeli region; Puuhakkeen hankinta- ja tutkimusprojekti Mikkelin seudulla

    Energy Technology Data Exchange (ETDEWEB)

    Saksa, T. [Finnish Forest Research Inst., Suonenjoki (Finland). Suonenjoki Research Station; Auvinen, P. [Mikkeli city (Finland). Dept. of Agriculture and Forestry

    1996-12-31

    In 1993-94, a large-scale energywood production chain started as a co-operation project by the Mikkeli city forest office and local forestry societies. In 1995 over 115 000 m{sup 3} (about 85 000 MWh of energy) of wood chips were delivered to Pursiala heat and power plant in Mikkeli. About 75 % of these chips was forest processed chips. About 70 % of the forest processed chips was whole tree chips from improvement cuttings of young forest stands and the rest was logging waste chips from regeneration cutting areas. The average total delivery costs of forest processed chips after reduction of energywood and other subsidies were approximately 45 FIM/m{sup 3} (60 FIM/MWh) for the whole tree chips and 38 FIM/m{sup 3} (50 FIM/MWh) for logging waste chips. The delivery costs of forest processed chips could meet the target of Bioenergy Research Programme (45 FIM/MWh) only in the most favourable cases. In an average the delivery costs were about 9 FIM/MWh more than the price obtained when sold to the heat and power plant. However the wood chip production created 27 new jobs and the increase of income to the local economy was about 2.2 milj. FIM /year. The local communities got new tax revenue about 3 FIM/MWh. The gain for the forestry was approximated to be 5 - 6 FIM/MWh. The resources of forest processed chips were studied on the basis of stand measurements. According to the study the most remarkable energywood resources were in young thinning stands on Oxalis-Myrtillus and Myrtillus forest site types. On Oxalis-Myrtillus type almost every and on Myrtillus type every second stand included energywood more than 40 m{sup 3}/ha

  1. Chemical changes and increased degradability of wheat straw and oak wood chips treated with the white rot fungi Ceriporiopsis subvermispora and Lentinula edodes

    NARCIS (Netherlands)

    Kuijk, van Sandra J.A.; Sonnenberg, Anton S.M.; Baars, Johan J.P.; Hendriks, Wouter H.; Río, del José C.; Rencoret, Jorge; Gutiérrez, Ana; Ruijter, de Norbert C.A.; Cone, John W.

    2017-01-01

    Wheat straw and oak wood chips were incubated with Ceriporiopsis subvermispora and Lentinula edodes for 8 weeks. Samples from the fungal treated substrates were collected every week for chemical characterization. L. edodes continuously grew during the 8 weeks on both wheat straw and oak wood chips,

  2. Identification and characterisation of factors affecting losses in the large-scale, non-ventilated bulk storage of wood chips and development of best storage practices

    Energy Technology Data Exchange (ETDEWEB)

    Garstang, J.; Weekes, A.; Poulter, R.; Bartlett, D.

    2002-07-01

    The report describes the findings of a study to determine the factors affecting the commercial storage of wood chips for biomass power generation in the UK. The UK's first such plant in North Yorkshire uses a mixture of forestry residues and short rotation coppice (SRC) willow, where problems with the stored fuel highlighted the need to determine best storage practices. Two wood chip piles were built (one with willow chip and the other with wood chips from board leaf forestry residues) and monitored (moisture, temperature, chemical composition, spore numbers and species, heat and air flows, bulk density, etc). Local weather data was also obtained. Recommendations for future storage practices are made.

  3. Price of forest chips decreasing

    International Nuclear Information System (INIS)

    Hakkila, P.

    2001-01-01

    Use of forest chips was studied in 1999 in the national Puuenergia (Wood Energy) research program. Wood combusting heating plants were questioned about are the main reasons restricting the increment of the use of forest chips. Heating plants, which did not use forest chips at all or which used less than 250 m 3 (625 bulk- m 3 ) in 1999 were excluded. The main restrictions for additional use of forest chips were: too high price of forest chips; lack of suppliers and/or uncertainty of deliveries; technical problems of reception and processing of forest chips; insufficiency of boiler output especially in winter; and unsatisfactory quality of chips. The price of forest chips becomes relatively high because wood biomass used for production of forest chips has to be collected from wide area. Heavy equipment has to be used even though small fragments of wood are processed, which increases the price of chips. It is essential for forest chips that the costs can be pressed down because competition with fossil fuels, peat and industrial wood residues is hard. Low market price leads to the situation in which forest owner gets no price of the raw material, the entrepreneurs operate at the limit of profitability and renovation of machinery is difficult, and forest chips suppliers have to sell the chips at prime costs. Price of forest chips has decreased significantly during the past decade. Nominal price of forest chips is now lower than two decades ago. The real price of chips has decreased even more than the nominal price, 35% during the past decade and 20% during the last five years. Chips, made of small diameter wood, are expensive because the price includes the felling costs and harvesting is carried out at thinning lots. Price is especially high if chips are made of delimbed small diameter wood due to increased the work and reduced amount of chips. The price of logging residue chips is most profitable because cutting does not cause additional costs. Recovery of chips is

  4. Acquisition of wood fuel at the Joseph C. McNeil Generating Station

    Energy Technology Data Exchange (ETDEWEB)

    Kropelin, W. [Burlington Electric Dept., VT (United States)

    1993-12-31

    The Joseph C. McNeil Generating Station is the world`s largest single boiler, municipally-owned, wood-fired electrical generating plant. The 50 megawatt McNeil Station is located in Burlington, Vermont and is owned by several Vermont public and private electric utilities. The operator and majority owner is the City of Burlington Electric Department (BED). Wood fuel procurement for the McNeil Station has been conducted in an environmentally sensitive way. Harvesting is carried out in conformance with a comprehensive wood chip harvesting policy and monitored by professional foresters. Unpredictable levels of Station operation require rigid adherence to a wood storage plan that minimizes the risk of over heating and spontaneous combustion of stockpiled fuel.

  5. Catalytic fast pyrolysis of white oak wood in-situ using a bubbling fluidized bed reactor

    Science.gov (United States)

    Catalytic fast pyrolysis was performed on white oak wood using two zeolite-type catalysts as bed material in a bubbling fluidized bed reactor. The two catalysts chosen, based on a previous screening study, were Ca2+ exchanged Y54 (Ca-Y54) and a proprietary ß-zeolite type catalyst (catalyst M) both ...

  6. Steam-explosion pretreatment of wood: effect of chip size, acid, moisture content and pressure drop

    Energy Technology Data Exchange (ETDEWEB)

    Brownell, H.H.; Yu, E.K.C.; Saddler, J.N.

    1986-06-01

    Material balances for pentosan, lignin, and hexosan, during steam-explosion pretreatment of aspenwood, showed almost quantitative recovery of cellulose in the water-insoluble fraction. Dilute acid impregnation resulted in more selective hydrolysis of pentosan relative to undesirable pyrolysis, and gave a more accessible substrate for enzymatic hydrolysis. Thermocouple probes, located inside simulated aspenwood chips heated in 240 degrees C-saturated steam, showed rapid heating of air-dry wood, whereas green or impregnated wood heated slowly. Small chips, 3.2 mm in the fiber direction, whether green or air dry gave approximately equal rates of pentosan destruction and solubilization, and similar yields of glucose and of total reducing sugars on enzmatic hydrolysis with Trichoderma harzianum. Partial pyrolysis, destroying one-third of the pentosan of aspenwood at atmospheric pressure by dry steam at 276 degrees C, gave little increase in yield of reducing sugars on enzymatic hydrolysis. Treatment with saturated steam at 240 degrees C gave essentially the same yields of butanediol and ethanol on fermentation with Klebsiella pneumoniae, whether or not 80% of the steam was bled off before explosion and even if the chips remained intact, showing that explosion was unnecessary. 17 references.

  7. Effect of oxalic acid pretreatment of wood chips on manufacturing medium-density fiberboard

    Science.gov (United States)

    Xianjun Li; Zhiyong Cai; Eric Horn; Jerrold E. Winandy

    2011-01-01

    The main objective of this study was to evaluate the effect of oxalic acid (OA) wood chips pretreatment prior to refining, which is done to reduce energy used during the refining process. Selected mechanical and physical performances of medium-density fiberboard (MDF) – internal bonding (IB), modulus of elasticity (MOE), modulus of rupture (MOR), water absorption (WA)...

  8. Supply chains of forest chip production in Finland

    Energy Technology Data Exchange (ETDEWEB)

    Kaerhae, Kalle (Metsaeteho Oy, Helsinki (Finland)), e-mail: kalle.karha@metsateho.fi

    2010-07-15

    The Metsaeteho study investigated how logging residue chips, stump wood chips, and chips from small sized thinning wood and large-sized (rotten) roundwood used by heating and power plants were produced in Finland in 2008. Almost all the major forest chip suppliers in Finland were involved in the study. The total volume of forest chips supplied in 2008 by these suppliers was 6.5 TWh. The study was implemented by conducting an e-mail questionnaire survey and telephone interviews. Research data was collected in March-May 2009. The majority of the logging residue chips and chips from small-sized thinning wood were produced using the roadside chipping supply chain in Finland in 2008. The chipping at plant supply chain was also significant in the production of logging residue chips. 70% of all stump wood chips consumed were comminuted at the plant and 29% at terminals. The role of the terminal chipping supply chain was also significant in the production of chips from logging residues and small-sized wood chips. When producing chips from large-sized (rotten) roundwood, nearly a half of chips were comminuted at plants and more than 40% at terminals

  9. Supply systems of forest chip production in Finland

    Energy Technology Data Exchange (ETDEWEB)

    Kaerhae, K. (Metsaeteho Oy, Helsinki (Finland)), e-mail: kalle.karha@metsateho.fi

    2010-07-01

    The Metsaeteho study investigated how logging residue chips, stump wood chips, and chips from small-diameter thinning wood and large-sized (rotten) roundwood used by heating and power plants were produced in Finland in 2009. Almost all the major forest chip suppliers in Finland were involved in the study. The total volume of forest chips supplied in 2009 by these suppliers was 8,4 TWh. The study was implemented by conducting an e-mail questionnaire survey and telephone interviews. Research data was collected from March-May, 2010. The majority of the logging residue chips and chips from small-diameter thinning wood were produced using the roadside chipping supply system in Finland in 2009. The chipping at plant supply system was also significant in the production of logging residue chips. Nearly 70 % of all stump wood chips consumed were comminuted at the plant and 28 % at terminals. The role of the terminal chipping supply system was also significant in the production of chips from logging residues and small-diameter wood chips. When producing chips from large-sized (rotten) roundwood, similarly roughly 70 % of chips were comminuted at plants and 23 % at terminals. (orig.)

  10. Supply chains of forest chip production in Finland

    Energy Technology Data Exchange (ETDEWEB)

    Kaerhae, K. (Metsaeteho Oy, Helsinki (Finland)), Email: kalle.karha@metsateho.fi

    2009-07-01

    The Metsaeteho study investigated how logging residue chips. stump wood chips, and chips from small-sized thinning wood and large-sized (rotten) roundwood used by heating and power plants were produced in Finland in 2008. Almost all the major forest chip suppliers in Finland were involved in the study. The total volume of forest chips supplied in 2008 by these suppliers was 6,5 TWh. The study was implemented by conducting an e-mail questionnaire survey and telephone interviews. Research data was collected in March-May 2009. The majority of the logging residue chips and chips from small-sized thinning wood were produced using the roadside chipping supply chain in Finland in 2008. The chipping at plant supply chain was also significant in the production of logging residue chips. 70% of all stump wood chips consumed were comminuted at the plant and 29% at terminals. The role of the terminal chipping supply chain was also significant in the production of chips from logging residues and small-sized wood chips. When producing chips from large-sized (rotten) roundwood, nearly a half of chips were comminuted at plants and more than 40 % at terminals. (orig.)

  11. Evaluation of a wood chipping system for eucalyptus tops for energy; Avaliacao de um sistema de cavaqueamento de ponteiras de eucalipto para aproveitamento energetico

    Energy Technology Data Exchange (ETDEWEB)

    Canto, Juliana Lorensi do [Universidade Federal do Rio Grande do Norte (UFRN), Natal, RN (Brazil); Machado, Carlos Cardoso; Souza, Amaury Paulo de; Sant' Anna, Cleverson de Mello [Departamento de Engenharia Florestal da Universidade Federal de Vicosa, UFV, MG (Brazil)], E-mails: machado@ufv.br, amaury@ufv.br, cleverson@ufv.br; Seixas, Fernando [Universidade de Sao Paulo (USP), Sao Paulo, SP (Brazil). Escola Superior de Agricultura Luiz de Queiroz, ESALQ], E-mail: fseixas@esalq.usp.br

    2011-11-15

    The objective of this study was to evaluate the performance and to estimate costs of a wood chipping system for tree tops, which are considered residuals from wood harvesting, to be used for energy. The study was developed in a forest industry in the Para State, located in the north region of Brazil. The system was comprised by one wood chipper, two forwarders and one front loader. Data collection was based on time study, fuel consumption and chips load weighting. System average productivity was 17.51 tonnes per effective hour. Machine utilization rate was 51.9% due to many delays, mainly for repair and maintenance of the chipper. Chips transportation was considered to be the critical point of the system, due to some lack of trucks available for blowing chips. The system can produce between 94 and 162 times more energy than the energy consumed. System cost per effective hour was R$ 376.56, which means R$ 21.51/tonne of chips or R$ 2.70/G J. (author)

  12. Modeling wood dynamics, jam formation, and sediment storage in a gravel-bed stream

    Science.gov (United States)

    Eaton, B. C.; Hassan, M. A.; Davidson, S. L.

    2012-12-01

    In small and intermediate sized streams, the interaction between wood and bed material transport often determines the nature of the physical habitat, which in turn influences the health of the stream's ecosystem. We present a stochastic model that can be used to simulate the effects on physical habitat of forest fires, climate change, and other environmental disturbances that alter wood recruitment. The model predicts large wood (LW) loads in a stream as well as the volume of sediment stored by the wood; while it is parameterized to describe gravel bed streams similar to a well-studied field prototype, Fishtrap Creek, British Columbia, it can be calibrated to other systems as well. In the model, LW pieces are produced and modified over time as a result of random tree-fall, LW breakage, LW movement, and piece interaction to form LW jams. Each LW piece traps a portion of the annual bed material transport entering the reach and releases the stored sediment when the LW piece is entrained and moved. The equations governing sediment storage are based on a set of flume experiments also scaled to the field prototype. The model predicts wood loads ranging from 70 m3/ha to more than 300 m3/ha, with a mean value of 178 m3/ha: both the range and the mean value are consistent with field data from streams with similar riparian forest types and climate. The model also predicts an LW jam spacing that is consistent with field data. Furthermore, our modeling results demonstrate that the high spatial and temporal variability in sediment storage, sediment transport, and channel morphology associated with LW-dominated streams occurs only when LW pieces interact and form jams. Model runs that do not include jam formation are much less variable. These results suggest that river restoration efforts using engineered LW pieces that are fixed in place and not permitted to interact will be less successful at restoring the geomorphic processes responsible for producing diverse, productive

  13. Enzymatic pretreatment of wood chips for energy reductions in TMP production. A method for ranking of enzymes; Enzymatisk foerbehandling av flis foer energibesparing vid TMP tillverkning. Metod foer rankning av enzymer

    Energy Technology Data Exchange (ETDEWEB)

    Viforr, Silvia

    2010-11-15

    The production of thermomechanical pulp (TMP) demands high levels of energy. This, together with current expensive energy prices of nowadays results in significant costs, which is the reason why there is a demand for processes that require less energy. One way of reducing energy consumption in TMP refining could be to pretreat the wood chips with enzymes before the subsequent refining step. However, enzymes molecules are relatively large, which limits the impregnation process, and so the pores in the fibre walls are not large enough to fit the size of the enzymes. By mechanically pretreating wood chips in a screw feeder and press equipment, this opens the wood structure significantly which increases enzyme penetration. If enzymes are used for reducing energy consumption in TMP processes, it is necessary to optimise the enzymatic effect during the pretreatment of wood chips. It is very expensive to evaluate completely the effect of enzymes in large scale refining. Thus there is a need for other relevant methods for rapidly and effectively evaluating the energy saving effects when it comes to refining enzymatic pretreated wood chips. The aim of this project was to find a method for ranking of enzymes for pretreatment of chips for energy savings at TMP production. This method was to be independent of the type of enzyme used and of the type of pretreated wood chips involved. In order to asses the method for ranking enzymes being used in the pretreatment of chips to reduce energy input during refining, a comparison between the method and a mill trial was carried out in the mill trial. A known chemical pretreatment was used; here it was sulphonation of the wood chips before refining with low sulphite levels. Further, a laboratory wing refiner was used as an evaluation equipment. The trial started with the running conditions for a wing refiner that the best correspond with industrial refining. An evaluation was made on the effect of enzymatic pretreatment on energy

  14. Hydrodynamic studies in designing of fluidized bed system

    International Nuclear Information System (INIS)

    Mohamad Puad Abu; Muhd Noor Muhd Yunus; Syed Nasaruddin Syed Idris

    2002-01-01

    Fluidized bed process have been used mostly in the petroleum and paper industries, and for processing nuclear wastes, spent cook liquor, wood chips, and sewage sludge disposal. Even at MINT some of the equipment available used this principal. Before we use or purchase this equipment, it is very grateful if we could understand how the system has been designed. The hydrodynamic fluidization studies is very important in designing of fluidized bed system especially in determining the minimum fluidizing velocity, terminal velocity, flexibility of operation, slugging condition, bubble size and velocity, and transport disengaging height. They can be determined either by calculation or experimentation. This paper will highlight the hydrodynamic study that need to be performed in designing of fluidized bed system so that its can be used appropriately. (Author)

  15. The economic efficiency of forest energy wood chip production in regional use – A case study

    Directory of Open Access Journals (Sweden)

    Dalibor Šafařík

    2013-01-01

    Full Text Available This regional project case study deals with the limiting factors of economic efficiency in the production of forest energy wood chips. The evaluation of production efficiency made use of data obtained from the Lesy města Brna, a.s. (Forest of the City of Brno, Corp., which were subjected to two static methods of investment evaluation: an analysis of the tipping point and determination of the limit of variable costs and a dynamic modified tipping point analysis using cash flow (i.e. cash break even analysis. The results have confirmed an established hypothesis, namely that the decisive factor in the profitability of the production of forest energy wood chips hinges on the costs incurred in the gathering of raw material and the distribution of the produced chips. The results include a further limiting factor: transportation costs to the final consumption location. The output of the study is a recommendation that the concentration of residual forest materials not exceed a distance of 250 m from the place of production to the point of disintegration and that the transport distance of energy chips not exceed 50 km from the place of disintegration to the final consumption point. These limiting values help quantify the full internal costs per cost unit, full internal cost profitability, total revenue profitability and annual profitability expressed in terms of fixed assets depreciation without factoring in financial aid.

  16. The classification of wood chips parameters by crushing of waste cane from different varieties of grapevine

    Directory of Open Access Journals (Sweden)

    Patrik Burg

    2008-01-01

    Full Text Available This work deales with exploitatives parameters monitoring of wood shreder PEZZOLATO 110 Mb by crushing of waste cane of six varieties. The results shows that the wood shreders efficiency, fuel consumption and the wood chips elements size can be influenced by varieties characters of cane. The va­lued machines efficiency was 230–470 kg . h−1 by average volume 40.70 % water in wood. The hig­hest values by cane crushing had the variety Saint Laurent (0.47 t . h−1 and the lowest variety ­Blauer Portugieser (0.23 t . h−1. The specific consumption of petrol Natural 95 was 4.52.10−3–8.12.10−3 l . kg−1. The average middle elements lenght was 6.64 mm by crushed varieties.

  17. Power generation from waste wood

    Energy Technology Data Exchange (ETDEWEB)

    Nitsche, H

    1980-04-18

    Since the energy crisis, power generation from waste wood has become increasingly important. The most profitable way to use waste wood in woodworking plants with an annual production of 100 to 150,000 m/sup 3/ solid measure of wood chips and bark is by combustion and thermal energy recovery. In plants with an annual production of 10,000 m/sup 3/ solid measure of wood chips and bark, electric power generation is a suitable application.

  18. Development of stoker-burner wood chip combustion systems for the UK market

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-07-01

    The document makes a case for the development of a design of wood chip stoker-burner more suited to the UK than those currently imported from Sweden and Finland. The differences would centre on market conditions, performance and cost-effectiveness and the devices would be manufactured or part-manufactured in the UK. Econergy Limited was contracted by the DTI as part of its Sustainable Energy Programmes to design and construct an operational prototype stoker-burner rated at 120 kWth. A test rig was built to: (i) study modified burner heads and (ii) develop control hardware and a control strategy. Both (i) and (ii) are described. Tests brought about an increase in performance of the burner head and its wet wood performance. It was considered that further improvements are achievable and six areas for future study were suggested.

  19. Experimental investigation and mathematical modelling of wood combustion in a moving grate boiler

    International Nuclear Information System (INIS)

    Zhang, Xiaohui; Chen, Qun; Sharifi, Vida; Swithenbank, Jim; Bradford, Richard

    2010-01-01

    The use of biomass to generate energy offers significant environmental advantages for the reduction in emissions of greenhouse gases. The main objective of this study was to investigate the performance of a small scale biomass heating plant: i.e. combustion characteristics and emissions. An extensive series of experimental tests was carried out at a small scale residential biomass heating plant i.e. wood chip fired boiler. The concentrations of CO, NO x , particulate matter in the flue gas were measured. In addition, mathematical modelling work using FLIC and FLUENT codes was carried out in order to simulate the overall performance of the wood fired heating system. Results showed that pollutant emissions from the boiler were within the relative emission limits. Mass concentration of CO emission was 550-1600 mg/m 3 (10% O 2 ). NO x concentration in the flue gas from the wood chips combustion varied slightly between 28 and 60 ppmv. Mass concentration of PM 10 in the flue gas was 205 mg/m 3 (10% O 2 ) The modelling results showed that most of the fuel was burnt inside the furnace and little CO was released from the system due to the high flue gas temperature in the furnace. The injection of the secondary air provided adequate mixing and favourable combustion conditions in the over-bed chamber in the wood chips fired boiler. This study has shown that the use of wood heating system result in much lower CO 2 emissions than from a fossil fuel e.g. coal fired heating system. (author)

  20. Investigation of ESEM/EDX to measure liquor penetration and diffusion in Eucalyptus grandis wood chips during kraft pulping

    CSIR Research Space (South Africa)

    Grzeskowiak, V

    2011-01-01

    Full Text Available Environmental scanning electron microscopy coupled with energy dispersive x-ray (ESEM/EDX) was optimised to measure the penetration and diffusion of cooking liquor into Eucalyptus grandis wood chips during kraft pulping. The moisture content...

  1. Kinetics of pyrolysis and combustion of spherical wood particles in a fluidized bed

    International Nuclear Information System (INIS)

    Mazziotti di Celso, Giuseppe; Rapagnà, Sergio; Prisciandaro, Marina; Zanoelo, Everton Fernando

    2014-01-01

    Highlights: • H 2 , CO 2 , CO and CH 4 released during wood pyrolysis were experimentally monitored. • CO 2 formed by burning the residual tar/char mixture was experimentally determined. • The kinetics of species production was reproduced with two simplified models. • The increase of the bed reactor temperature statistically enhanced the gas yield. • The pyrolysis time is statistically reduced by decreasing the particle size. - Abstract: The kinetics of wood pyrolysis and combustion of residual fuel at different particle diameters and temperatures was investigated. A known mass of wooden spheres was fed at the top of a fluidized bed reactor filled with olivine particles and fluidized with nitrogen. The concentration of H 2 , CO 2 , CO and CH 4 was on-line monitored with gas analyzers. An irreversible first order reaction was applied to describe the biomass pyrolysis. The rate constant was dependent on the average temperature of wood particle, obtained by solving the transient one-dimensional problem of heat conduction in a sphere. The rate for an irreversible second order reaction between the residual fuel and oxygen at the fluid–solid interface, which takes a finite resistance to mass transfer into account, was adopted to describe the combustion. The semi-empirical kinetic models for pyrolysis and combustion were able to describe, with certain limitations inherent to model simplifications, the experimental transient results of molar flow rates of major released species. A statistical model based on the results of the factorial design of experiments (3 2 ) confirmed a statistical significant effect of temperature and wood particle diameter on the gas yield and time of pyrolysis, respectively

  2. Integrated production of merchantable wood and wood fuels in industry; Teollisuuden ainespuun ja puupolttoaineen integroitu tuotanto

    Energy Technology Data Exchange (ETDEWEB)

    Kuvaja, K [Enso Oy, Imatra (Finland). Forest Dept.

    1997-12-01

    The aim of this project is the economically profitable integrated harvesting of industrial wood and firewood especially in harvesting of small-diameter first thinning wood. The research in 1994 was concentrated on improvement of the quality of the chipping methods based on chain-flail debarking chipping method, and on determination of the possible utilisation targets for the fuel fraction. A reasonably large drum debarking test was also carried out at the industrial scale debarking station of the Enocell Oy. More than 80 000 m{sup 3} of first thinning wood was delivered by Enocell during this project. The quality of wood chips, produced using the chain-flail delimbing method, could be improved in the case of pine nearly to the required quality level, but additional measures are still needed in the case of birch. The fuel fraction deliveries to different points of utilisation was started. The particle size of the fuel fraction appeared to be good after crushing. In 1995 a chain-flail-drum debarking chipping unit was developed to improve and homogenise the quality of chips. (orig.)

  3. Energy wood. Part 2b: Wood pellets and pellet space-heating systems

    International Nuclear Information System (INIS)

    Nussbaumer, T.

    2002-01-01

    The paper gives an overview on pellet utilization including all relevant process steps: Potential and properties of saw dust as raw material, pellet production with drying and pelletizing, standardization of wood pellets, storage and handling of pellets, combustion of wood pellets in stoves and boilers and applications for residential heating. In comparison to other wood fuels, wood pellets show several advantages: Low water content and high heating value, high energy density, and homogeneous properties thus enabling stationary combustion conditions. However, quality control is needed to ensure constant properties of the pellets and to avoid the utilization of contaminated raw materials for the pellet production. Typical data of efficiencies and emissions of pellet stoves and boilers are given and a life cycle analysis (LCA) of wood pellets in comparison to log wood and wood chips is described. The LCA shows that wood pellets are advantageous thanks to relatively low emissions. Hence, the utilization of wood pellet is proposed as a complementary technology to the combustion of wood chips and log wood. Finally, typical fuel cost of wood pellets in Switzerland are given and compared with light fuel oil. (author)

  4. Combined heat and power unit using renewable raw materials. A cogeneration power plant with wood chips and pellets; BHKW auf Basis nachwachsender Rohstoffe. KWK mit Holzhackschnitzeln und Pellets

    Energy Technology Data Exchange (ETDEWEB)

    Lennartz, Marc Wilhelm

    2013-07-15

    The combined heat and power units of the next generation operate with renewable resources. The plants working with wood chips or pellets now are ready for mass production. So, farmers and foresters, trade and municipalities may pile in the decentralized, energetic self-sufficiency. Two companies have developed procedures with which combined heat and power plants based can be operated on wood chips or pellets.

  5. Integrated production of merchantable wood and wood fuels in industry; Teollisuuden ainespuun ja puupoltto-aineen integroitu tuotanto

    Energy Technology Data Exchange (ETDEWEB)

    Kuvaja, K [Enso-Gutzeit Oy, Imatra (Finland). Forest Dept.

    1997-12-31

    The aim of this project is the economically profitable integrated harvesting of industrial wood and firewood especially in harvesting of small-diameter first thinning wood. The research in 1994 was concentrated on improvement of the quality of the chipping methods based on chain-flail debarking chipping method, and on determination of the possible utilization targets for the fuel fraction. A reasonably large drum debarking test was also carried out at the industrial scale debarking station of the Enocell Oy. More than 80 000 m{sup 3} of first thinning wood was delivered by Enocell during this project. The quality of wood chips, produced using the chain-flail delimbing method, could be improved in the case of pine nearly to the required quality level, but additional measures are still needed in the case of birch. The fuel fraction deliveries to different points of utilization was started. The particle size of the fuel fraction appeared to be good after crushing. In 1995 a chain-flail-dry drum debarking chipping unit was developed to improve and homogenize the quality of chips

  6. Integrated production of merchantable wood and wood fuels in industry; Teollisuuden ainespuun ja puupoltto-aineen integroitu tuotanto

    Energy Technology Data Exchange (ETDEWEB)

    Kuvaja, K. [Enso-Gutzeit Oy, Imatra (Finland). Forest Dept.

    1996-12-31

    The aim of this project is the economically profitable integrated harvesting of industrial wood and firewood especially in harvesting of small-diameter first thinning wood. The research in 1994 was concentrated on improvement of the quality of the chipping methods based on chain-flail debarking chipping method, and on determination of the possible utilization targets for the fuel fraction. A reasonably large drum debarking test was also carried out at the industrial scale debarking station of the Enocell Oy. More than 80 000 m{sup 3} of first thinning wood was delivered by Enocell during this project. The quality of wood chips, produced using the chain-flail delimbing method, could be improved in the case of pine nearly to the required quality level, but additional measures are still needed in the case of birch. The fuel fraction deliveries to different points of utilization was started. The particle size of the fuel fraction appeared to be good after crushing. In 1995 a chain-flail-dry drum debarking chipping unit was developed to improve and homogenize the quality of chips

  7. The effect of particle size and amount of inoculum on fungal treatment of wheat straw and wood chips

    NARCIS (Netherlands)

    Kuijk, van Sandra J.A.; Sonnenberg, Anton S.M.; Baars, Johan J.P.; Hendriks, Wouter H.; Cone, John W.

    2016-01-01

    Background: The aim of this study was to optimize the fungal treatment of lignocellulosic biomass by stimulating the colonization. Wheat straw and wood chips were treated with Ceriporiopsis subvermispora and Lentinula edodes with various amounts of colonized millet grains (0.5, 1.5 or 3.0 % per g

  8. Life?cycle impacts of ethanol production from spruce wood chips under high-gravity conditions

    OpenAIRE

    Janssen, Matty; Xiros, Charilaos; Tillman, Anne-Marie

    2016-01-01

    Background Development of more sustainable biofuel production processes is ongoing, and technology to run these processes at a high dry matter content, also called high-gravity conditions, is one option. This paper presents the results of a life?cycle assessment (LCA) of such a technology currently in development for the production of bio-ethanol from spruce wood chips. Results The cradle-to-gate LCA used lab results from a set of 30 experiments (or process configurations) in which the main p...

  9. Significance of wood extractives for wood bonding.

    Science.gov (United States)

    Roffael, Edmone

    2016-02-01

    Wood contains primary extractives, which are present in all woods, and secondary extractives, which are confined in certain wood species. Extractives in wood play a major role in wood-bonding processes, as they can contribute to or determine the bonding relevant properties of wood such as acidity and wettability. Therefore, extractives play an immanent role in bonding of wood chips and wood fibres with common synthetic adhesives such as urea-formaldehyde-resins (UF-resins) and phenol-formaldehyde-resins (PF-resins). Extractives of high acidity accelerate the curing of acid curing UF-resins and decelerate bonding with alkaline hardening PF-resins. Water-soluble extractives like free sugars are detrimental for bonding of wood with cement. Polyphenolic extractives (tannins) can be used as a binder in the wood-based industry. Additionally, extractives in wood can react with formaldehyde and reduce the formaldehyde emission of wood-based panels. Moreover, some wood extractives are volatile organic compounds (VOC) and insofar also relevant to the emission of VOC from wood and wood-based panels.

  10. Nutrient intake in the third instar larvae of Anomala cuprea and Protaetia orientalis submarmorea (Coleoptera; Scarabaeidae) from a mixture of cow dung and wood chips: Results from stable isotope analyses of nitrogen and carbon

    International Nuclear Information System (INIS)

    Koyama, Masahito; Iwata, Ryutaro; Yamane, Akiomi; Katase, Takao; Ueda, Shingo

    2003-01-01

    The nutrient intake of the third instar larvae of Anomala cuprea (Ac) and Protaerita orientalis submarmorea (Pos) (Colepotera: Scarabaeidae) from a mixture of cow dung and wood chips of two wood species (Cryptomeria japonica and Quercus mongolica), was assayed by the stable isotope technique. The values of δ 15 N and δ 13 C (deviations of 15 N/ 14 N and 13 C/ 12 C from the standard materials) were measured in the following samples: (1) the integument plus the head of the 3rd instar larvae of both species reared in 1999 autumn fed with a mixture of cow dung and wood chips or with leaf mold, (2) cow dung, (3) wood ships, and (4) leaf mold as the larval food before onset of rearing. The δ values of bodies of larvae fed with leaf mold differed with the beetle species. The δ 15 N values of the larval bodies of both species fed with the mixture were close to those of cow dung, whereas the δ 13 C values were in between those of cow dung and wood chips. Therefore, both species were presumed to obtain almost all their nitrogen from cow dung, and their carbon from both dung and wood chips. (author)

  11. Application of wood chips for soil mulching in the cultivation of ornamental grasses

    Directory of Open Access Journals (Sweden)

    Henschke Monika

    2016-12-01

    Full Text Available A mulch is a layer of material applied to the surface of the soil. Mulching plays an important role in the maintenance of green spaces. Organic materials are still sought for the preparation of mulches. Recently interest in wood chips has grown. The aim of the study was to determine the effect of mulching with pine and birch chips on the contents of phenolic compounds in the soil, as well as on the growth and flowering of ornamental grasses – Bouteloua gracilis (Kunth. Lag. ex Griffiths, Panicum virgatum L. and Pennisetum alopecuroides L. The content of phenolic compounds in the soil steadily increased from spring to autumn. Mulching led to a substantial increase in the level of phenolic compounds. In the first year of cultivation more phenolic compounds were released by chips of pine than birch, while in the second year this difference did not occur. Mulching had a negative impact on the growth and flowering of ornamental grasses, especially in the first year of cultivation. Ornamental grass sensitivity to the substances released from mulches decreased with the age of the plants and was dependent on the species – Bouteloua gracilis was found to be particularly sensitive.

  12. The effect of location and facility demand on the marginal cost of delivered wood chips from energy crops: A case study of the state of Tennessee

    International Nuclear Information System (INIS)

    Graham, R.L.; Liu, W.; Downing, M.; Noon, C.; Daly, M.; Moore, A.

    1995-01-01

    Cost-supply curves for delivered wood chips from short rotation woody crops were calculated for 21 regularly-spaced locations spanning the state of Tennessee. These curves were used to systematically evaluate the combined effects of location and facility demand on wood chip feedstock costs in Tennessee. The cost-supply curves were developed using BRAVO, a GIS-based decision support system which calculates marginal cost of delivering wood chips to a specific location given road network maps and maps of farmgate prices and supplies of woody chips from short rotation energy crops. Marginal costs of delivered chips varied by both facility location in the state and facility demand. Marginal costs were lowest in central Tennessee unless the facility demand was greater than 2.7 million dry Mg per year (3 million dry tons per year) in which case west Tennessee was the lowest cost region. Marginal costs rose rapidly with increasing facility demand in the mountainous eastern portion of the state. Transportation costs accounted for 18 to 29% of the delivered cost and ranged between $8 and $18/dry Mg ($7 and $16/dry ton). Reducing the expected farmer participation rate from 100% to 50% or 25% dramatically raised the marginal costs of feedstock supply in the east and central regions of the state. The analysis demonstrates the need to use geographically-specific information when projecting the potential costs and supplies of biomass feedstock

  13. Estimated Hardwood Volume Available for Wood Chipmills or Other Low Grade Uses

    Data.gov (United States)

    U.S. Environmental Protection Agency — The potential of wood chip mills to influence the distribution of harvests and the dynamics of wood fiber utilization has become an issue of concern. Where wood chip...

  14. Fluidized-Bed Gasification of Plastic Waste, Wood, and Their Blends with Coal

    Directory of Open Access Journals (Sweden)

    Lucio Zaccariello

    2015-08-01

    Full Text Available The effect of fuel composition on gasification process performance was investigated by performing mass and energy balances on a pre-pilot scale bubbling fluidized bed reactor fed with mixtures of plastic waste, wood, and coal. The fuels containing plastic waste produced less H2, CO, and CO2 and more light hydrocarbons than the fuels including biomass. The lower heating value (LHV progressively increased from 5.1 to 7.9 MJ/Nm3 when the plastic waste fraction was moved from 0% to 100%. Higher carbonaceous fines production was associated with the fuel containing a large fraction of coal (60%, producing 87.5 g/kgFuel compared to only 1.0 g/kgFuel obtained during the gasification test with just plastic waste. Conversely, plastic waste gasification produced the highest tar yield, 161.9 g/kgFuel, while woody biomass generated only 13.4 g/kgFuel. Wood gasification showed a carbon conversion efficiency (CCE of 0.93, while the tests with two fuels containing coal showed lowest CCE values (0.78 and 0.70, respectively. Plastic waste and wood gasification presented similar cold gas efficiency (CGE values (0.75 and 0.76, respectively, while that obtained during the co-gasification tests varied from 0.53 to 0.73.

  15. Fast pyrolysis of creosote treated wood ties in a fluidized bed reactor and analytical characterization of product fractions

    International Nuclear Information System (INIS)

    Jung, Su-Hwa; Koo, Won-Mo; Kim, Joo-Sik

    2013-01-01

    A fraction of creosote treated wood ties was pyrolyzed in a pyrolysis plant equipped with a fluidized bed reactor and char-separation system at different temperatures. Analyses of each pyrolysis product, especially the oil, were carried out using a variety of analytical tools. The maximum oil yield was obtained at 458 °C with a value of 69.3 wt%. Oils obtained were easily separated into two phases, a creosote-derived fraction (CDF) and a wood-derived fraction (WDF). Major compounds of the WDF were acetic acid, furfural and levoglucosan, while the CDF was mainly composed of polycyclic aromatic hydrocarbons (PAHs), such as 1-methylnaphthalene, biphenyl, acenaphthene, dibenzofuran, fluorene, phenanthrene, anthracene, fluoranthene and pyrene. HPLC analysis showed that the concentration of PAHs of the CDF obtained at 458 °C constituted about 22.5 wt% of the oil. - Highlights: • Creosote treated wood ties was stably pyrolyzed in a fluidized bed reactor. • Pyrolysis oil contained extremely low metal content due to the char removal system. • Bio-oil components was quantitatively analyzed by relative response factor. • Creosote-derived pyrolysis oil fraction was composed of PHAs and has a high caloric value (39 MJ/kg)

  16. Manufacture of wood-pellets doubles. Biowatti Oy started a wood pellet plant in Turenki

    International Nuclear Information System (INIS)

    Rantanen, M.

    1999-01-01

    Wood pellets have many advantages compared to other fuels. It is longest processed biofuel with favorable energy content. It is simple to use, transport and store. Heating with wood pellets is cheaper than with light fuel oil, and approximately as cheap as utilization of heavy fuel oil, about 110 FIM/MWh. The taxable price of wood pellets is about 550 FIM/t. Stokers and American iron stoves are equally suitable for combustion of wood pellets. Chip fueled stokers are preferred in Finland, but they are also suitable for the combustion of wood pellets. Wood pellets is an environmentally friendly product, because it does not increase the CO 2 load in the atmosphere, and its sulfur and soot emissions are relatively small. The wood pelletizing plant of Biowatti Oy in Turenki was started in an old sugar mill. The Turenki sugar mill was chosen because the technology of the closed sugar factory was suitable for production of wood pellets nearly as such, and required only by slight modifications. A press, designed for briquetting of sugar beat clippings makes the pellets. The Turenki mill will double the volume of wood pellet manufacture in Finland during the next few years. At the start the annual wood pellet production will be 20 000 tons, but the environmental permit allows the production to be increased to 70 000 tons. At first the mill uses planing machine chips as a raw material in the production. It is the most suitable raw material, because it is already dry (moisture content 8-10%), and all it needs is milling and pelletizing. Another possible raw material is sawdust, which moisture content is higher than with planing machine chips. Most of the wood pellets produced are exported e.g. to Sweden, Denmark and Middle Europe. In Sweden there are over 10 000 single-family houses using wood pellets. Biowatti's largest customer is a power plant located in Stockholm, which combusts annually about 200 000 tons of wood pellets

  17. Methanol production from eucalyptus wood chips. Attachment IV. Health and safety aspects of the eucalypt biomass to methanol energy system

    Energy Technology Data Exchange (ETDEWEB)

    Fishkind, H.H.

    1982-06-01

    The basic eucalyptus-to-methanol energy process is described and possible health and safety risks are identified at all steps of the process. The toxicology and treatment for exposure to these substances are described and mitigating measures are proposed. The health and safety impacts and risks of the wood gasification/methanol synthesis system are compared to those of the coal liquefaction and conversion system. The scope of this report includes the health and safety risks of workers (1) in the laboratory and greenhouse, where eucalyptus seedlings are developed, (2) at the biomass plantation, where these seedlings are planted and mature trees harvested, (3) transporting these logs and chips to the refinery, (4) in the hammermill, where the logs and chips will be reduced to small particles, (5) in the methanol synthesis plant, where the wood particles will be converted to methanol, and (6) transporting and dispensing the methanol. Finally, the health and safety risks of consumers using methanol is discussed.

  18. Trace element partitioning in ashes from boilers firing pure wood or mixtures of solid waste with respect to fuel composition, chlorine content and temperature

    Energy Technology Data Exchange (ETDEWEB)

    Saqib, Naeem, E-mail: naeem.saqib@oru.se; Bäckström, Mattias, E-mail: mattias.backstrom@oru.se

    2014-12-15

    Highlights: • Different solids waste incineration is discussed in grate fired and fluidized bed boilers. • We explained waste composition, temperature and chlorine effects on metal partitioning. • Excessive chlorine content can change oxide to chloride equilibrium partitioning the trace elements in fly ash. • Volatility increases with temperature due to increase in vapor pressure of metals and compounds. • In Fluidized bed boiler, most metals find themselves in fly ash, especially for wood incineration. - Abstract: Trace element partitioning in solid waste (household waste, industrial waste, waste wood chips and waste mixtures) incineration residues was investigated. Samples of fly ash and bottom ash were collected from six incineration facilities across Sweden including two grate fired and four fluidized bed incinerators, to have a variation in the input fuel composition (from pure biofuel to mixture of waste) and different temperature boiler conditions. As trace element concentrations in the input waste at the same facilities have already been analyzed, the present study focuses on the concentration of trace elements in the waste fuel, their distribution in the incineration residues with respect to chlorine content of waste and combustion temperature. Results indicate that Zn, Cu and Pb are dominating trace elements in the waste fuel. Highly volatile elements mercury and cadmium are mainly found in fly ash in all cases; 2/3 of lead also end up in fly ash while Zn, As and Sb show a large variation in distribution with most of them residing in the fly ash. Lithophilic elements such as copper and chromium are mainly found in bottom ash from grate fired facilities while partition mostly into fly ash from fluidized bed incinerators, especially for plants fuelled by waste wood or ordinary wood chips. There is no specific correlation between input concentration of an element in the waste fuel and fraction partitioned to fly ash. Temperature and chlorine

  19. Solar heating, wood chips and pellets at Harpsund. An evaluation; Solvaerme, flis och pellets paa Harpsund. Utvaerdering

    Energy Technology Data Exchange (ETDEWEB)

    Nilsson, Leif; Perers, Bengt

    2006-06-15

    Harpsund is well-known for being the representation residence for the Swedish prime minister. Besides this function, it is also a production unit for milk and meat, with a livestock of about 500 animals. At Harpsund, a new production plant for heating and domestic hot water with a new distribution net was built by the Swedish authorities. Wood chips from the forests belonging to the estate are used for the heat production, together with wood pellets and solar heat. The old heating system was based on a technique with local production in each building and was in need of modernization. The new plant has been designed very attractively - great care has been taken to make it fit into the atmosphere of the surroundings. The solar collectors are placed on the roof of a garage for farming machines. The heat central contains three burners: one for wood chips with thermal power 250 kW, one 400 kW burner for pellets and one small 25 kW burner for pellets. The smallest unit is intended to support the solar system during the summer season. From the garage with the 327 m{sup 2} Aquasol Big AR solar collectors the solar heated glycol/ water is transported to the heat central in a culvert. The distance is 150 m. At the heat central, there is also a heat accumulator with a volume of 40 m{sup 3} of water. This is used both for the burners and for the solar heat. The monitoring and analysis of the plant show that it has good reliability and it is evident that the production capacity is adequate for all conceivable climate conditions. During one year of monitoring, the heat central produced 1,494 MWh of which 86 % came from wood chips, 9 % from pellets and 5 % from solar heat. It is unfavourable that the solar heat has to work against the return temperature of the heat distribution system. Also, the collector area seems to be somewhat too large for the demand for domestic hot water. The result for the specific investment for solar heat is therefore high: 13.21 SEK/kWh,year. It might

  20. Hot water extracted wood fiber for production of wood plastic composites (WPCs)

    Science.gov (United States)

    Manuel Raul Pelaez-Samaniego; Vikram Yadama; Eini Lowell; Thomas E. Amidon; Timothy L. Chaffee

    2013-01-01

    Undebarked ponderosa pine chips were treated by hot water extraction to modify the chemical composition. In the treated pine (TP) , the mass was reduced by approximately 20%, and the extract was composed mainly of degradation products of hemicelluloses. Wood flour produced from TP and unextracted chips (untreated pine, UP) was blended with high-density polyethylene (...

  1. The effect of adding urea, manganese and linoleic acid to wheat straw and wood chips on lignin degradation by fungi and subsequent

    NARCIS (Netherlands)

    Kuijk, van S.J.A.; Sonnenberg, A.S.M.; Baars, J.J.P.; Hendriks, W.H.; Cone, J.W.

    2016-01-01

    The aim of this study was optimizing Ceriporiopsis subvermispora and Lentinula edodes pre-treatment of wheat straw and wood chips by adding urea, manganese and linoleic acid. Optimization was defined as more lignin degradation and an increase in in vitro gas

  2. Modeling of electrodialytic and dialytic removal of Cr, Cu and As from CCA-treated wood chips

    DEFF Research Database (Denmark)

    Ribeiro, Alexandra; Rodriguez-Maroto, J.M.; Mateus, Eduardo

    2007-01-01

    + and NO3 used as electrolyte solutions in the electrode compartments, and oxalate ions and protons incorporated with the oxalic acid solution during wood chips incubation. The model simulation also takes into account that OH generated on the cathode, during electrodialytic remediation, is periodically...... neutralized by addition of nitric acid in the cathode compartment. The anion and cation-exchange membranes are simply represented as ionic filters that preclude the transport of co-ions (the cations and anions respectively) with the exception of H+, which is retarded but considered to pass through the anion...

  3. Application of the differential colorimetry and polyphenolic profile to the evaluation of the chromatic quality of Tempranillo red wines elaborated in warm climate. Influence of the presence of oak wood chips during fermentation.

    Science.gov (United States)

    Gordillo, Belén; Cejudo-Bastante, María Jesús; Rodríguez-Pulido, Francisco J; González-Miret, M Lourdes; Heredia, Francisco J

    2013-12-01

    The effect of adding American oak wood chips during fermentation on Tempranillo red wines elaborates in a warm climate has been studied. Our attention was focused on the tristimulus colorimetry, differential colorimetry and phenolic compounds related to wine colour. This technique was applied as an oenological alternative to the conventional winemaking for avoiding the common fall of colour of red wines elaborated in warm climates. The addition of oak wood chips promoted the colour enhancement and stabilisation, producing wines with a notably darker colour and with more bluish tonality. This fact was also related to the significantly higher content of some phenolic compounds. On the basis of the results, it could be affirmed that the addition of oak wood chips during fermentation induced visually perceptible colour changes (by the analysis of ΔEab(*), %Δ(2)L, %Δ(2)C and %Δ(2)H), mainly in a quantitative way, and also a lower percentage of diminution of colour. Copyright © 2013 Elsevier Ltd. All rights reserved.

  4. Effects of wood chip ash fertilization on soil chemistry in a Norway spruce plantation on a nutrient-poor soil

    DEFF Research Database (Denmark)

    Ingerslev, Morten; Hansen, Mette; Pedersen, Lars Bo

    2014-01-01

    of wood chip ash application on soil chemistry in a 44-year-old Norway spruce (Picea abies) plantation on a nutrient-poor soil in Denmark and to investigate the effect of applying different ash types and doses. Soil samples were collected and analyzed 2.5years (3 growing seasons) after ash application....... This study shows that, regardless of ash formulation, preparation or dose, application of wood ash to forest soil has a liming effect in the O-horizon manifested as an increase in CECe, BS and pH. This effect was not seen in the mineral soil within the time frame of this study. At the same time, an increase...... in Cd was found in the O-horizon, corresponding to the amount added in the ashes. Generally, no other increase in soil contents of the heavy metals was seen. Hardening of the wood ash did not decrease the chemical impact on the soil chemistry as compared to non-treated ash whereas an increase in ash...

  5. Pressured fluidized-bed gasification experiments with wood, peat and coal at VTT in 1991-1992. Test facilities and gasification experiments with sawdust

    Energy Technology Data Exchange (ETDEWEB)

    Kurkela, E; Staahlberg, P; Laatikainen, J [Technical Research Centre of Finland, Espoo (Finland). Lab. of Fuel and Process Technology

    1994-12-31

    Fluidized-bed air gasification of Finnish pine saw dust was studied in the PDU-scale test facilities of VTT to support the development of simplified integrated gasification combined-cycle processes by providing new information on the formation and behaviour of different gas impurities in wood gasification. The gasifier was operated at 4-5 bar pressure and at 880-1 020 deg C Product gas was cleaned by ceramic candle filters operated at 490-715 deg C. Concentrations of tars, fixed nitrogen species and vapour-phase alkali metals were determined in different operating conditions. Carbon conversion exceeded 95 deg C in all test periods although the gasifier was operated without recycling the cyclone or filter fines back to the reactor. However, at the gasification temperature of 880-900 deg C more than 5 deg C of the wood carbon was converted to tars. The total concentration of tars (compounds heavier than benzene) was reduced from 6 000 to 3 000 mg/m{sup 3}n by increasing the gasification temperature from 880 deg C to 1 000 deg C. The expected catalytic effects of calcium on tar decomposition could not be achieved in these experiments by feeding coarse dolomite into the bed. The use of sand or aluminium oxide as an inert bed material did neither lead to any decrease in tar concentrations. However, the tar concentrations were dramatically reduced in the cogasification experiments, when a mixture of approximately 50 deg C/50 deg C wood and coal was used as the feed stock. Wood nitrogen was mainly converted into ammonia, while the concentrations of HCN and organic nitrogen containing compounds were very low

  6. Pressured fluidized-bed gasification experiments with wood, peat and coal at VTT in 1991-1992. Test facilities and gasification experiments with sawdust

    Energy Technology Data Exchange (ETDEWEB)

    Kurkela, E.; Staahlberg, P.; Laatikainen, J. [Technical Research Centre of Finland, Espoo (Finland). Lab. of Fuel and Process Technology

    1993-12-31

    Fluidized-bed air gasification of Finnish pine saw dust was studied in the PDU-scale test facilities of VTT to support the development of simplified integrated gasification combined-cycle processes by providing new information on the formation and behaviour of different gas impurities in wood gasification. The gasifier was operated at 4-5 bar pressure and at 880-1 020 deg C Product gas was cleaned by ceramic candle filters operated at 490-715 deg C. Concentrations of tars, fixed nitrogen species and vapour-phase alkali metals were determined in different operating conditions. Carbon conversion exceeded 95 deg C in all test periods although the gasifier was operated without recycling the cyclone or filter fines back to the reactor. However, at the gasification temperature of 880-900 deg C more than 5 deg C of the wood carbon was converted to tars. The total concentration of tars (compounds heavier than benzene) was reduced from 6 000 to 3 000 mg/m{sup 3}n by increasing the gasification temperature from 880 deg C to 1 000 deg C. The expected catalytic effects of calcium on tar decomposition could not be achieved in these experiments by feeding coarse dolomite into the bed. The use of sand or aluminium oxide as an inert bed material did neither lead to any decrease in tar concentrations. However, the tar concentrations were dramatically reduced in the cogasification experiments, when a mixture of approximately 50 deg C/50 deg C wood and coal was used as the feed stock. Wood nitrogen was mainly converted into ammonia, while the concentrations of HCN and organic nitrogen containing compounds were very low

  7. Selective ligninolysis of wheat straw and wood chips by the white-rot fungus Lentinula edodes and its influence on in vitro rumen degradability

    NARCIS (Netherlands)

    Kuijk, van S.J.A.; Rio, del José C.; Rencoret, Jorge; Gutiérrez, Ana; Sonnenberg, A.S.M.; Baars, J.J.P.; Hendriks, W.H.; Cone, J.W.

    2016-01-01

    Background: The present work investigated the influence of lignin content and composition in the fungal
    treatment of lignocellulosic biomass in order to improve rumen degradability. Wheat straw and wood chips,
    differing in lignin composition, were treated with Lentinula edodes for 0, 2, 4, 8

  8. Availability and use of wood-based fuels in Finland in 2020

    Energy Technology Data Exchange (ETDEWEB)

    Kaerhae, K.; Raesaenen, T.; Pajuoja, H. (Metsaeteho Oy, Helsinki (Finland)), Email: kalle.karha@metsateho.fi, Email: tapio.rasanen@metsateho.fi, Email: heikki.pajuoja@metsateho.fi; Elo, J.; Lahtinen, P. (Poeyry Energy Oy, Espoo (Finland)), Email: juha.elo@poyry.com, Email: perttu.lahtinen@poyry.com

    2009-07-01

    In Finland the overall usage target set for forest chips is 12 million m3, i.e. around 24 TWh by the year 2020. The objective of the research carried out by Metsaeteho Oy and Poeyry Energy Oy was to produce a total analysis as realistic as possible of the possibilities of increasing the use of wood-based fuels in Finland by 2020. The research shows that the growth objective set in the long-term Climate and Energy Strategy can be attained through the supply and demand for wood-based fuels. However, realizing this potential would require major investments in the entire forest chip production system, because the competitiveness of wood-based fuels in energy generation is currently not at a sufficient level. The emission trading has a strong influence on the competitiveness of wood-based fuels and the use of such fuels in energy plants. Increasing the proportion of wood-based fuels is very difficult at the current price level of the EU emission allowances (10 euro/t CO{sub 2}). A strong increase in the use of wood-based fuels would require a price level of over 25 euro/t CO{sub 2} of emission allowances. Considering the huge resources required by the forest chip production system and the current low competitiveness of forest chips, it is estimated that the use of forest chips in Finland will reach the level of 20 TWh at the earliest by the year 2020. (orig.)

  9. ASSESSMENT OF THE MOISTURE EFFECT ON GASEOUS PRODUCTS OF SELF-HEATING OF WOOD CHIPS

    Directory of Open Access Journals (Sweden)

    Hana VĚŽNÍKOVÁ

    2017-12-01

    Full Text Available Biofuels are stored in large quantities and may be susceptible to self-ignition. The possible methods of indication of temperature increase include the analysis of the gaseous products of heating where concentrations of certain gases may increase with increasing temperature. Gas release is also affected by the moisture of the material given that the moisture level changes surface accessibility for oxygen on the one side and serves as a catalyst of the oxidation reactions on the other. The present project analysed the effect of temperature and moisture on gaseous products of heating of wood chips, one of frequently used biofuels, with the aim to determine a suitable gaseous indicator of beginning self-ignition.

  10. Findings on pollutant formation in wood and chip board combustion. Erkenntnisse zur Schadstoffbildung bei der Verbrennung von Holz und Spanplatten

    Energy Technology Data Exchange (ETDEWEB)

    Marutzky, R.

    1991-10-01

    Combustion experiments were carried out using wood and several types of chip boards with binders on the basis of urea, melamine and phenol formaldehyde resins, polyureas, and PVC. The combustion process was observed, and the flue gas constituents in case of incomplete combustion were analyzed. The origins of the various organic and inorganic materials were discussed taking account of the results of pyrolysis experiments. (orig.).

  11. The case for wood-fuelled heating

    International Nuclear Information System (INIS)

    Bent, Ewan

    2001-01-01

    This article looks at the wood heating industry in the UK and examines the heat market and the growth potential in the domestic, public, agricultural and commercial sectors. The current status of wood-fueled heating technology is considered, along with log and chip boilers, and the use of pellet fuel. The economics of wood-fuelled heating, the higher level of utilisation of wood-fuelled heating by utilities in northern European countries compared with the UK, and the barriers to the exploitation of wood fuelled heating are examined

  12. Partial debarking of energy wood stems in production of high quality fuel chips and fuel logs (DryMe); Runkopuun osittainen kuorinta metsaehakkeen ja pilkkeidentuotantoketjussa (DryMe) - PUUT58

    Energy Technology Data Exchange (ETDEWEB)

    Sikanen, L.; Roeser, D.; Tahvanainen, T.; Prinz, R. [Finnish Forest Research Institute, Joensuu (Finland); Erkkilae, A.; Heikkinen, A.; Hillebrand, K. [VTT Technical Research Centre of Finland, Jyvaeskylae (Finland)

    2007-07-01

    Small wood chip fueled heating plants require high quality chips in order to achieve low service need and problem free running. Low moisture content is considered to be the most important quality factor in wood based fuels. On the other hand, drying should be efficient and handy as a part of supply chain. Rapidly growing small-scale wood energy business needs new methods to ensure availability of high quality fuel. Partial debarking of both boreal broadleaved and coniferous species is known as effective method to dry timber during storing. Anyhow, proper place for storing and convenient weather conditions are needed. Partly debarked stems could be also the raw material for wood pellets. In Finnish studies, for example, storing over one summer took moisture content down from 40% to 27% with partly debarked birch logs. Some preliminary tests have been made also in Scotland and England with baled residues and small diameter logs without debarking. Even British climate seems to be suitable for natural drying of logs. In Central Europe, natural drying is crucial in order to achieve high quality of forest chips for heating. The aims of the DryMe-project are: (1) Remodify and study harvester head which is capable to debark energy wood stems. The aim is to create modified feeding rolls and delimbing knives or extra debarking device, which remove effectively 30-50% of bark during normal harvesting work. The success of debarking will be tested by field experiments and drying trials. Method should work with Silver Birch, Scots Pine and Lodgepole Pine. (2) Test different kinds of bark scarifying patterns and methods according to their capability to evaporate water out from the logs in natural drying. (orig.)

  13. Forest biomass and wood waste resources

    Science.gov (United States)

    K. Skog; P. Lebow; D.. Dykstra; P.. Miles; B.J. Stokes; R.D. Perlack; M. Buford; J. Barbour; D. McKeever

    2011-01-01

    This chapter provides estimates of forest biomass and wood waste quantities, as well as roadside costs (i.e., supply curves) for each county in the contiguous United States. Roadside price is the price a buyer pays for wood chips at a roadside in the forest, at a processing mill location in the case of mill residue, or at a landfill for urban wood wastes prior to any...

  14. Large wood budget assessment along a gravel bed river affected by volcanic eruption: the Rio Blanco study case (Chile).

    Science.gov (United States)

    Oss-Cazzador, Daniele; Iroume, Andres; Lenzi, Mario; Picco, Lorenzo

    2016-04-01

    Wood in riverine environments exerts different functions on ecological and geomorphic settings, influencing morphological processes, and increasing risks for sensitive structures. Large wood (LW) is defined as wood material, dead or alive, larger than 10 cm in diameter and 1 m in length. Natural hazards can strongly increase the presence of LW in waterways and flood events can transport it affecting the ecosystem and landscape. This study aims to increase the knowledge of wood budget, considering the effects of two subsequent slight flood events along a sub-reach of the Rio Blanco gravel bed river , in Chilean Patagonia, strongly affected by the eruption of Chaiten volcano in 2008. The volcanic eruption affected almost 3,5 km 2 of evergreen forest on the southern (left) bank, because of primary direct effects from pyroclastic density currents and lahar-floods that caused deposition up to 8 m of reworked tephra, alluvium, and wood on floodplains and terrace along the Rio Blanco. After the eruption, there was a considerable increase of LW into the main channel: into the bankfull channel, volume exceeds 100 m 3 /ha. Field surveys were carried out in January and March 2015, before and after two slight flood events (Recurrence Intervals lower than 1 year). The pre-event phase permitted to detect and analyze the presence of LW into the study area, along a 80 m-long reach of Rio Blanco (7500 m 2 . Every LW element was manually measured and described, a numbered metal tag was installed, and the position was recorded by GPS device. In January, there was a total amount of 113 m 3 /ha, 90% accumulated in LW jams (WJ) and 10% as single logs. The LW was characterized by mean dimensions of 3,36 m height, 0,25 m diameter and 0,26 m 3 volume, respectively. The WJ are characterized by wide range of dimension: volume varies from 0,28 m 3 to 672 m 3 , length from 1,20 m to 56 m, width from 0,40 m to 8,70 m and height from 0,20 m to 3 m, respectively. After the flood events, field

  15. Oxalic acid pretreatment of rice straw particles and loblolly pine chips : release of hemicellulosic carbohydrates

    Science.gov (United States)

    Xianjun Li; Zhiyong Cai; Eric Horn; Jerrold E. Winandy

    2011-01-01

    This study was conducted to evaluate the effect of oxalic acid (OA) pretreatment on carbohydrates released from rice straw particles and wood chips. The results showed that OA treatment accelerated carbohydrates extraction from rice straw particles and wood chips. OA pretreatment dramatically increased the amount of carbohydrates extracted, up to 24 times for wood...

  16. Rats Housed on Corncob Bedding Show Less Slow-Wave Sleep

    OpenAIRE

    Leys, Laura J; McGaraughty, Steve; Radek, Richard J

    2012-01-01

    Despite the reported advantages of corncob bedding, questions have emerged about how comfortable animals find this type of bedding as a resting surface. In this study, encephalography (EEG) was used to compare the effects of corncob and aspen-chip bedding on rat slow-wave sleep (SWS). According to a facility-wide initiative, rats that were weaned on aspen-chip bedding were switched to corncob bedding in home cages and EEG recording chambers. Spontaneous EEG recordings obtained for 5 wk after ...

  17. Barge loading facilities in conjunction with wood chipping and sawlog mill, Tennessee River Mile 145. 9R: Environmental assessment

    Energy Technology Data Exchange (ETDEWEB)

    1990-08-01

    The purpose of this Environmental Assessment (EA) is to evaluate the environmental consequences of approving, denying, or adopting reasonable alternatives to a request for barge loading facilities. These facilities would serve a proposed wood chipping and sawlog products operation at Tennessee River Mile (TRM) 145.9, right descending bank, (Kentucky Lake), in Perry County, Tennessee. The site is located between Short Creek and Peters Landing. The applicant is Southeastern Forest Products, L.P. (SFP), Box 73, Linden, Tennessee and the proposed facilities would be constructed on or adjacent to company owned land. Portions of the barge terminal would be constructed on land over which flood easement rights are held by the United States of America and administered by the Tennessee Valley Authority (TVA). The US Army Corps of Engineers (CE) and TVA have regulatory control over the proposed barge terminal facilities since the action would involve construction in the Tennessee River which is a navigable water of the United States. The wood chipping and sawlog products facilities proposed on the upland property are not regulated by the CE or TVA. On the basis of the analysis which follows, it has been determined that a modified proposal (as described herein) would not significantly affect the quality of the human environment, and does not require the preparation of an environmental impact statement. 8 refs.

  18. European wood-fuel trade

    International Nuclear Information System (INIS)

    Hillring, B.; Vinterbaeck, J.

    2001-01-01

    This paper discusses research carried out during the l990s on European wood fuel trade at the Department of Forest Management and Products, SLU, in Sweden. Utilisation of wood-fuels and other biofuels increased very rapidly in some regions during that period. Biofuels are replacing fossil fuels which is an effective way to reduce the future influence of green house gases on the climate. The results indicate a rapid increase in wood-fuel trade in Europe from low levels and with a limited number of countries involved. The chief products traded are wood pellets, wood chips and recycled wood. The main trading countries are, for export, Germany and the Baltic states and, for import, Sweden, Denmark and to some extent the Netherlands. In the future, the increased use of biofuel in European countries is expected to intensify activity in this trade. (orig.)

  19. Preferences of group-housed female mice regarding structure of softwood bedding.

    Science.gov (United States)

    Kirchner, J; Hackbarth, H; Stelzer, H D; Tsai, P-P

    2012-04-01

    Bedding influences various parameters in the housing of laboratory mice, such as health, physiology and behaviour (often considered as being integral parts of welfare). Notwithstanding existent studies about bedding preferences of individually tested mice, data about group-housed mice are still lacking. The aim of this study was to find out the structure preference for softwood bedding of group-housed mice. One hundred and eight 8-week-old female mice (C57BL6/JOlaHsd and BALB/cOlaHsd) were housed in groups of three and were given one-week free access to two different bedding structures at a time. In three test combinations, softwood shaving bedding was tested versus softwood chip bedding products of three different particle sizes (fine/medium/coarse-grained). The preference test was performed in a DoubleCage system composed of two Makrolon type IIL cages, connected by a perspex tunnel. This validated system was able to detect the crossings of each individual animal with correct crossing time and direction. On the basis of these data, dwelling times on the particular bedding structures were statistically analysed as a parameter for bedding preferences. In all three test combinations, a highly significant shaving preference was detected. On average, mice spent 70% of their dwelling time on the shavings. This preference was more explicit during the light period and in C57BL/6J mice. The relative ranking of the bedding structures was: shavings > coarse-grained chips > medium chips = fine chips. By means of these results, a shaving structure as bedding can be recommended for laboratory mice, whereas fine chip structures should be avoided.

  20. Modified precision-husky progrind H-3045 for chipping biomass

    Science.gov (United States)

    Dana Mitchell; Fernando Seixas; John. Klepac

    2008-01-01

    A specific size of whole tree chip was needed to co-mill wood chips with coal. The specifications are stringent because chips must be mixed with coal, as opposed to a co-firing process. In co-firing, two raw products are conveyed separately to a boiler. In co-milling, such as at Alabama Power's Plant Gadsden, the chip and coal mix must pass through a series of...

  1. Handling wood shavings

    Energy Technology Data Exchange (ETDEWEB)

    1974-09-18

    Details of bulk handling equipment suitable for collection and compressing wood waste from commercial joinery works are discussed. The Redler Bin Discharger ensures free flow of chips from storage silo discharge prior to compression into briquettes for use as fuel or processing into chipboard.

  2. Continuous Fixed-Bed Column Study and Adsorption Modeling: Removal of Lead Ion from Aqueous Solution by Charcoal Originated from Chemical Carbonization of Rubber Wood Sawdust

    Directory of Open Access Journals (Sweden)

    Swarup Biswas

    2015-01-01

    Full Text Available The efficiency of chemically carbonized rubber wood sawdust for the removal of lead ion from the aqueous stream was investigated by column process. Chemically carbonized rubber wood sawdust was prepared by treating the sawdust with H2SO4 and HNO3. Maximum removal of lead ion in column process was found as 38.56 mg/g. The effects of operating parameters such as flow rate, bed depth, concentration, and pH were studied in column mode. Experimental data confirmed that the adsorption capacity increased with the increasing inlet concentration and bed depth and decreased with increasing flow rate. Thomas, Yoon-Nelson, and Adams-Bohart models were used to analyze the column experimental data and the relationship between operating parameters. Chemically carbonized rubber wood sawdust was characterized by using Fourier transform infrared spectroscopy. Scanning electron microscope was also utilized for morphological analysis of the adsorbent. Furthermore X-ray fluorescence spectrum analysis and energy dispersive X-ray spectroscopy were also used for the confirmation of lead adsorption process.

  3. Whole tree chips for fuel and pulp can cut mill energy costs

    Energy Technology Data Exchange (ETDEWEB)

    Morey, J

    1979-01-01

    Wood that is decaying and going to waste amounts to over 5 billion tons, enough to replace the present oil consumption of the United States. Environmental thinning--removal of dead, dying, and less desirable trees--leaves room for other trees to grow. Environmental thinning should be acceptable to private landowners, making almost every stand of timber available for energy harvest. Environmental thinning uses a small feller buncher shear, a small to medium grapple skidder, and a whole tree chipper. Five or six men, two or three feller bunchers, two grapple skidders, and a whole tree chipper can produce 250 to 300 green tons of whole tree chips per day and deliver it to an energy plant for $10 to $12 per ton. Demand for wood for energy will raise pulpwood prices unless industry adopts whole tree utilization and environmental thinning. Wood energy provides a market for low grade wood. The whole tree chipper can separate stem chips for pulping and top chips, with bark and foliage, for energy uses. A dirt separator available on the Morbark total Chiparvestor helps remove sand, about 40% of the bark, and about 50% of twigs and foliage. Because the fiber has a value as energy, it will be economical to build better screening systems, providing cleaner pulp chips. After screening, bark will remain, but some mills are converting to 100% bark chips. A study indicates that converting from oil to wood and from roundwood to whole tree chips can result in a savings of $4 to $8 million per year for a 1,000 tpd pulp and paper mill.

  4. Solving wood chip transport problems with computer simulation.

    Science.gov (United States)

    Dennis P. Bradley; Sharon A. Winsauer

    1976-01-01

    Efficient chip transport operations are difficult to achieve due to frequent and often unpredictable changes in distance to market, chipping rate, time spent at the mill, and equipment costs. This paper describes a computer simulation model that allows a logger to design an efficient transport system in response to these changing factors.

  5. Wood, the indigenous energy source. 1100 plants built in 20 years, all of them 'Swiss made'

    International Nuclear Information System (INIS)

    Wahlen, B.

    1999-01-01

    The company HOBAG Brienz, Ltd., specialised in the field of automatic wood-burning plants, continuously developed its unique system over the past 20 years and has more than 1100 satisfied clients in Switzerland as well as in foreign countries. It is equally dealing with log boilers, wood chip boilers, or pellet boilers. Nowadays, the company is seen as the market leader for modern, full automatic log-burning plants and wood conditioning equipment including containers for logs or wood chips

  6. Trace element partitioning in ashes from boilers firing pure wood or mixtures of solid waste with respect to fuel composition, chlorine content and temperature.

    Science.gov (United States)

    Saqib, Naeem; Bäckström, Mattias

    2014-12-01

    Trace element partitioning in solid waste (household waste, industrial waste, waste wood chips and waste mixtures) incineration residues was investigated. Samples of fly ash and bottom ash were collected from six incineration facilities across Sweden including two grate fired and four fluidized bed incinerators, to have a variation in the input fuel composition (from pure biofuel to mixture of waste) and different temperature boiler conditions. As trace element concentrations in the input waste at the same facilities have already been analyzed, the present study focuses on the concentration of trace elements in the waste fuel, their distribution in the incineration residues with respect to chlorine content of waste and combustion temperature. Results indicate that Zn, Cu and Pb are dominating trace elements in the waste fuel. Highly volatile elements mercury and cadmium are mainly found in fly ash in all cases; 2/3 of lead also end up in fly ash while Zn, As and Sb show a large variation in distribution with most of them residing in the fly ash. Lithophilic elements such as copper and chromium are mainly found in bottom ash from grate fired facilities while partition mostly into fly ash from fluidized bed incinerators, especially for plants fuelled by waste wood or ordinary wood chips. There is no specific correlation between input concentration of an element in the waste fuel and fraction partitioned to fly ash. Temperature and chlorine content have significant effects on partitioning characteristics by increasing the formation and vaporization of highly volatile metal chlorides. Zinc and cadmium concentrations in fly ash increase with the incineration temperature. Copyright © 2014 Elsevier Ltd. All rights reserved.

  7. Estimating potentials of solid wood-based fuels in Finland in 2020

    Energy Technology Data Exchange (ETDEWEB)

    Kaerhae, Kalle; Raesaenen, Tapio; Pajuoja, Heikki (Metsaeteho Oy, Helsinki (Finland)), e-mail: kalle.karha@metsateho.fi; Elo, Juha; Lahtinen, Perttu (Poeyry Energy Oy, Espoo (Finland))

    2010-07-15

    In the context of the Long-term Climate and Energy Strategy, it is estimated that the primary use of woodbased fuels in Finland will be 93 to 97 TWh by the year 2020. The overall target set for forest chips is 12 million m3, i.e. around 24 TWh. The objective of the research carried out by Metsaeteho Oy and Poeyry Energy Oy was to produce as realistic as possible a total analysis of the possibilities of increasing the usage of wood-based fuels in Finland by 2020. The research showed that the growth objective set in the Long-term Climate and Energy Strategy can be attained through the supply and demand of wood-based fuels. However, realizing this potential would require major investments in the entire forest chip production system, because the competitiveness of wood-based fuels in energy generation is currently not at a sufficient level. Considering the huge resources required by the forest chip production system and the current low competitiveness of forest chips, it is estimated that the use of forest chips in Finland will reach the level of 20 TWh at the earliest by the year 2020

  8. Production of wood fuels from young forests

    International Nuclear Information System (INIS)

    Korpilahti, A.

    1998-01-01

    National forest invention data shows that more than 200 000 ha of thinnings should be carried out annually. The stemwood accumulation corresponding to this is about 13 million m 3 . The share of industrial wood is about 5.7 million m 3 , so the energy wood potential is about 7.0 million m 3 . Because the growing stock can use the nutrients liberated from logging residues the topwood mass should not be totally harvested, and at the barren areas it should not be harvested at all. Even the difficult terrain restricts in some extent the harvesting of logging residues. After these reductions the economically harvestible energy wood potential has been estimated to be 5.1 million m 3 corresponding to about 0.9 million toe. The amount of first thinnings has during the last few years been only about one third of the need. The accumulation in the first thinning phase could be about 40-80 m 3 /ha. The annual young stand treatment area has usually been about 200 000 ha, but during the last few years it has remained to a little over 100 000 ha. Harvesting of wood fuels from young stands, based on a lot-chipping method and the traditional production chains, was investigated in the national Bioenergy Research Programme. Equipment of suitable size and price are needed for harvesting of small-diameter trees. The profitability of mechanized harvesting can be improved significantly if the single-tree processing is replaced with multi- tree processing. Multi-tree harvesting can be carried out in all production chains, felling-bunching, in partial and pulpwood harvesting, as well as with bare felling machines and harvesters. About 60 % of the stems were processed with a prototype machine, tested in treatment of young forests. About 70 % of fellings in felling-bunching, already in commercial use, was processed as multi- tree processing, and about 80 % in the partial-tree harvesting. The felling of pulpwood as partial trees was about 25-30 % faster as multi-tree processing than with

  9. The value chain of small-sized energy wood

    Energy Technology Data Exchange (ETDEWEB)

    Karttunen, K.; Foehr, J.; Ranta, T. (Lappeenranta Univ. of Technology, Mikkeli (Finland), LUT Energy), Email: kalle.karttunen@lut.fi, Email: jarno.fohr@lut.fi, Email: tapio.ranta@lut.fi; Ahtikoski, A. (The Finnish Forest Research Institute, Rovaniemi (Finland)), Email: anssi.ahtikoski@metla.fi; Valsta, L. (Helsinki Univ. (Finland), Dept. of Forest Economics), Email: lauri.valsta@helsinki.fi

    2009-07-01

    Finland has agreed to increase the share of renewable energy to the level of 38% by the end of 2020. Most of the increase is to be based on bioenergy. According to the National Climate and Energy Strategy, the need for forest biomass will come to more than 20 TWh, or some 10 million cubic meters per year. Energy wood from young stand thinnings are the biomass resource with the most potential at the moment. The purpose of this study was to compare cost differences between forest management incorporating energy wood thinning and forest management based on traditional roundwood thinning. In addition, alternative supply chain costs for small-sized wood were studied. The results of the study show that it is worth considering the following points if the demand and average price for forest chips remain high. 1. Forest-owners: Forest management including energy wood thinning is financially feasible. 2. Supply chain: A terminal chipping chain enables large-scale procurement of small-sized energy wood. 3. Power plants: Currently, subsidies, emission trading, and decreasing pulpwood prices together enable large-scale use of small-sized wood for energy purposes. The value chain of small-sized energy wood in large-scale power plants could be mobilised. (orig.)

  10. The use of forest chips in Finland

    International Nuclear Information System (INIS)

    Hakkila, P.

    2001-01-01

    International commitments require the industrial world to restrict their greenhouse gas emissions. In Finland, where the annual timber cut per capita is more than ten times the average cut in the other EU countries, the primary means to reduce CO 2 emissions is to replace fossil fuels with forest biomass. The annual consumption of wood-based energy corresponds to 6 million tonnes of oil equivalent (toe) or almost 20% of the total primary energy consumption. The goal is to rise the annual production of wood-based energy to 7.8 million toe by 2010. Substantial part of the targeted increase could be obtained by forest chips produced of unmerchantable small-diameter trees and logging residues. The goal for 2010 is to use 5 million solid m 3 of forest chips, which equals to 0.9 million toe. The use of forest chips is increasing. About 474 000 solid m 3 of forest chips were used as fuel in 1999. At the moment, the growth is rapid especially in cogeneration plants producing both heat and electricity. The growth is based primarily on chips obtained from logging residues. The price of forest chips decreased considerably during the 1990s but the price range remained wide. Chips made of logging residues are cheaper than those made of small trees. The average price of forest chips at the plant, VAT excluded, is about 53 FIM per MWh. In Sweden, the average price is more than 40% higher

  11. Influence of bedding type on mucosal immune responses.

    Science.gov (United States)

    Sanford, Amy N; Clark, Stephanie E; Talham, Gwen; Sidelsky, Michael G; Coffin, Susan E

    2002-10-01

    The mucosal immune system interacts with the external environment. In the study reported here, we found that bedding materials can influence the intestinal immune responses of mice. We observed that mice housed on wood, compared with cotton bedding, had increased numbers of Peyer's patches (PP) visible under a dissecting microscope. In addition, culture of lymphoid organs revealed increased production of total and virus-specific IgA by PP and mesenteric lymph node (MLN) lymphocytes from mice housed on wood, compared with cotton bedding. However, bedding type did not influence serum virus-specific antibody responses. These observations indicate that bedding type influences the intestinal immune system and suggest that this issue should be considered by mucosal immunologists and personnel at animal care facilities.

  12. Incorporating biopulping technology into wood yard operations

    Science.gov (United States)

    Gary M. Scott; Eric. Horn; Masood. Akhtar; Ross E. Swaney; Michael J. Lentz; David F. Shipley

    1998-01-01

    Biopulping is the treatment of wood chips and other lignocellulosic materials with lignin-degrading fungi prior to pulping. Ten years of industry-sponsored research has demonstrated the technical feasibility of the technology for mechanical pulping at a laboratory scale. Two 50-ton outdoor chip pile trials recently conducted at the USDA Forest Service, Forest Products...

  13. Life cycle impacts of ethanol production from spruce wood chips under high-gravity conditions.

    Science.gov (United States)

    Janssen, Matty; Xiros, Charilaos; Tillman, Anne-Marie

    2016-01-01

    Development of more sustainable biofuel production processes is ongoing, and technology to run these processes at a high dry matter content, also called high-gravity conditions, is one option. This paper presents the results of a life cycle assessment (LCA) of such a technology currently in development for the production of bio-ethanol from spruce wood chips. The cradle-to-gate LCA used lab results from a set of 30 experiments (or process configurations) in which the main process variable was the detoxification strategy applied to the pretreated feedstock material. The results of the assessment show that a process configuration, in which washing of the pretreated slurry is the detoxification strategy, leads to the lowest environmental impact of the process. Enzyme production and use are the main contributors to the environmental impact in all process configurations, and strategies to significantly reduce this contribution are enzyme recycling and on-site enzyme production. Furthermore, a strong linear correlation between the ethanol yield of a configuration and its environmental impact is demonstrated, and the selected environmental impacts show a very strong cross-correlation ([Formula: see text] in all cases) which may be used to reduce the number of impact categories considered from four to one (in this case, global warming potential). Lastly, a comparison with results of an LCA of ethanol production under high-gravity conditions using wheat straw shows that the environmental performance does not significantly differ when using spruce wood chips. For this comparison, it is shown that eutrophication potential also needs to be considered due to the fertilizer use in wheat cultivation. The LCA points out the environmental hotspots in the ethanol production process, and thus provides input to the further development of the high-gravity technology. Reducing the number of impact categories based only on cross-correlations should be done with caution. Knowledge of the

  14. EFFECT OF LIGNIN CONTENT OF Eucalyptus globulus WOOD IN KRAFT PULPING PERFORMANCE

    Directory of Open Access Journals (Sweden)

    Gabriel Valim Cardoso

    2011-03-01

    Full Text Available In this research, it was analyzed the lignin content effect of Eucalyptus globulus wood in kraft pulping optimization. Seventy-two laboratory cooking were made with wood chips obtained from six Eucalyptus globulus trees selected from a group of 50 trees. The wood chips from three trees with the lowest lignin content, with average 20,53%, were mixed proportionally based on the tree weights, obtaining the sample of low lignin content wood. The same was made to obtain the sample for wood chips with the highest lignin content, with average 23,02%. The two lignin levels were statistically different. The two wood samples had basic densities statistically not different. Using three maximum temperatures levels (160, 165 and 170ºC, and three active alkali charged (17, 18,5 and 20%, the wood chips were converted to kraft pulps. The pulps were then characterized to analyze the influence of the distinct treatments employed in the cooking on their properties. The effect of the cooking conditions was expressed by mathematical models in order to determine the optimum points for each of the evaluated properties. The optimization process indicated maximum temperature of 168ºC, and active alkali of 19%, for maximum kraft pulping yield to achieve kappa number 18; this result was for woods with low lignin content. For woods containing the high lignin content, the optimization showed maximum cooking temperature of 169ºC and active alkali of 19% for kappa number of 18. The average reduction of 2,49% in wood lignin content resulted a correspondent gain of 2,2% in the kraft yield (o.d. basis and a reduction on the active alkali charge of 1,2% (o.d. basis to achieve kappa numbers from 16 to 19, preserving pulp properties. If the option is to work with kappa number 19 instead of 16, the gain in kraft yield is approximately 2%. Therefore, when working with low lignin content wood and kappa number 19 instead of 16, a substantial gain of approximately 4,2% is obtained

  15. Development of fluidized bed combustion of biomass; Leijupolttoprosessin kehittaeminen vaikeille biopolttoaineille soveltuvaksi

    Energy Technology Data Exchange (ETDEWEB)

    Hiltunen, M; Vaehaenen-Koivuluoma, T [Foster Wheeler Energia Oy, Karhula (Finland)

    1997-10-01

    Some commercial BFB boilers burning biofuels, or biofuels and industrial wood wastes have suffered serious problems in bed material sintering. In worst cases the cumulation of reactive alkali compounds has caused total sintering of bed material even during a few days` operation. This presentation reports the results obtained from three separate cases, where sintering problems occurred. Boiler A burned biofuel with quartz sand and limestone addition. Boiler B burned softwood bark and industrial wood waste with sand addition. Boiler C burned softwood bark and sludge with sand addition. Due to the fuel used, bed sintering occurred in all boilers. Obviously, sintering was also influenced by some technical problems. Bed material samples have been analyzed with XRF and SEM-EDS techniques. According to these analyses, the main reason for sintering in boiler A is the cumulation of reactive potassium in bed material. In boiler B, the main reason is the fuel change from a mixture of softwood bark and industrial wood waste to pure industrial wood waste. The extra load of reactive sodium exceeded the critical concentration of alkali compounds in bed material. Also in boiler C, the fuel change from a mixture of softwood bark and sludge to pure softwood bark seems to be one of the reasons for bed sintering. After the fuel change the bed saturated with reactive potassium and the bed sintered. (orig.)

  16. Wood energy x 2 - Scenario for the development of wood energy use in Switzerland

    International Nuclear Information System (INIS)

    2004-01-01

    This study for the Swiss Agency for the Environment, Forests and Landscapes (SAEFL) and the Swiss wood-energy association (Holzenergie Schweiz) presents the results of a scenario-study that examined if, and under what conditions, doubling the use of wood energy in Switzerland could help reach carbon dioxide reduction targets. Two scenarios are presented that are based on high and low rates of growth for the number of automatic wood-chipping or pellets-fired installations. For both scenarios, figures are presented on the amount of wood used and the heating energy generated. The political and financial prerequisites for the scenarios are discussed and other boundary conditions are defined. The report draws conclusions from the study of the two scenarios and summarises the political action deemed necessary

  17. Environmental assessment of the atlas bio-energy waste wood fluidized bed gasification power plant. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Holzman, M.I.

    1995-08-01

    The Atlas Bio-Energy Corporation is proposing to develop and operate a 3 MW power plant in Brooklyn, New York that will produce electricity by gasification of waste wood and combustion of the produced low-Btu gas in a conventional package steam boiler coupled to a steam-electric generator. The objectives of this project were to assist Atlas in addressing the environmental permit requirements for the proposed power plant and to evaluate the environmental and economic impacts of the project compared to more conventional small power plants. The project`s goal was to help promote the commercialization of biomass gasification as an environmentally acceptable and economically attractive alternative to conventional wood combustion. The specific components of this research included: (1) Development of a permitting strategy plan; (2) Characterization of New York City waste wood; (3) Characterization of fluidized bed gasifier/boiler emissions; (4) Performance of an environmental impact analysis; (5) Preparation of an economic evaluation; and (6) Discussion of operational and maintenance concerns. The project is being performed in two phases. Phase I, which is the subject of this report, involves the environmental permitting and environmental/economic assessment of the project. Pending NYSERDA participation, Phase II will include development and implementation of a demonstration program to evaluate the environmental and economic impacts of the full-scale gasification project.

  18. Selective ligninolysis of wheat straw and wood chips by the white-rot fungus Lentinula edodes and its influence on in vitro rumen degradability

    OpenAIRE

    Kuijk, van, S.J.A.; Rio, del, José C.; Rencoret, Jorge; Gutiérrez, Ana; Sonnenberg, A.S.M.; Baars, J.J.P.; Hendriks, W.H.; Cone, J.W.

    2016-01-01

    Background: The present work investigated the influence of lignin content and composition in the fungaltreatment of lignocellulosic biomass in order to improve rumen degradability. Wheat straw and wood chips,differing in lignin composition, were treated with Lentinula edodes for 0, 2, 4, 8 and 12 wk and the changesoccurring during fungal degradation were analyzed using pyrolysis-gas chromatography-mass spectrometryand detergent fiber analysis.Results: L. edodes preferentially degraded lignin,...

  19. Reducing Respiratory Health Risks to Horses and Workers: A Comparison of Two Stall Bedding Materials

    Directory of Open Access Journals (Sweden)

    Markku Saastamoinen

    2015-10-01

    Full Text Available Stable air quality and the choice of bedding material are an important health issue both in horses and people working or visiting horse stables. Risks of impaired respiratory health are those that can especially be avoided by improving air quality in the stable. The choice of bedding material is particularly important in cold climate conditions; where horses are kept most of the day and year indoors throughout their life. This study examined the effect of two bedding materials; wood shavings and peat; on stable air quality and health of horses. Ammonia and dust levels were also measured to assess conditions in the stable. Ammonia was not detected or was at very low levels (<0.25 ppm in the boxes in which peat was used as bedding; but its concentration was clearly higher (1.5–7.0 ppm in stalls with wood shavings as bedding. Personal measurements of workers revealed quite high ammonia exposure (5.9 ppm8h in the boxes in which wood shavings were used; but no exposure was Animals 2015, 5 966 observed in stalls bedded with peat. The respiratory symptoms in horses increased regardless of the bedding material at the beginning of the study. The health status of the horses in the peat bedding group returned to the initial level in the end of the trial but horses bedded with wood shavings continued to be symptomatic. The hooves of the horses with peat bedding had a better moisture content than those of the horses bedded with wood shavings. The results suggest that peat is a better bedding material for horses than wood shavings regarding the health of both horses and stable workers.

  20. Wood fuel production technologies in EU countries

    Energy Technology Data Exchange (ETDEWEB)

    Hakkila, P [Finnish Forest Research Institute, Vantaa (Finland)

    1998-12-31

    The presentation reviews the major technologies used for the production of fuel chips for heating plants in Europe. Three primary options are considered: production of whole-tree chips from young trees for fuel; integrated harvesting of fiber and energy from thinning based on tree-section system; and production of fuel chips from logging residue in clear-cut areas after fully mechanized logging. The characteristics of the available biomass reserve and proven technology for its recovery are discussed. The employment effects of fuel chip production and the costs of wood fuels are also briefly discussed. (author) 3 refs., 3 figs.

  1. Wood fuel production technologies in EU countries

    Energy Technology Data Exchange (ETDEWEB)

    Hakkila, P. [Finnish Forest Research Institute, Vantaa (Finland)

    1997-12-31

    The presentation reviews the major technologies used for the production of fuel chips for heating plants in Europe. Three primary options are considered: production of whole-tree chips from young trees for fuel; integrated harvesting of fiber and energy from thinning based on tree-section system; and production of fuel chips from logging residue in clear-cut areas after fully mechanized logging. The characteristics of the available biomass reserve and proven technology for its recovery are discussed. The employment effects of fuel chip production and the costs of wood fuels are also briefly discussed. (author) 3 refs., 3 figs.

  2. Emission of organic substances from chip-boards

    Energy Technology Data Exchange (ETDEWEB)

    Deppe, H.J.

    1982-01-01

    A relatively small number of investigations on emissions of organic substances from chip-board is available up to now. The emissions known to date are caused by glues or other additives rather than by the wood itself. As concerns aminoplast glues (urea-formaldehyde or melamine-formaldehyde resins) the most important point of public interest has been the off-gassing of formaldehyde from chip-board. Chip-board with phenol-formaldehyde glues has been known in some cases to give off phenol. The formation of diamino diphenyl methane from isocyanate glues is still a matter of discussion. A further source for possible emissions are wood and fire protectives which are added during the manufacturing process. Finally, coating of chip-board may lead to emissions of organic substances. The lack of adequate detection methods has so far delayed the treatment of questions in relation to emissions from chip-board. Even now, there are numerous problems in this field especially when investigating isocyanate glues. Problems in relation to the origin of emissions due to the kind of glue used and the manufacturing process are discussed, and proposals are made how to solve some of these problems. The question of the health risk is dealt with from the view-point of the civil engineer and in an general economic context.

  3. Energy from wood - an overview

    International Nuclear Information System (INIS)

    Nussbaumer, T.

    2000-01-01

    The present publication is the introduction to a series of papers on fundamentals and applications of wood energy. It summarizes figures and data of the actual situation of fuel wood utilization in Switzerland and its potential for the future. Further, the advantages of bio-energy are discussed and the possibilities of funding for bio-energy in Switzerland are described. Wood contributes with 2.5% to the total energy demand in Switzerland nowadays. However, the utilization of wood energy can be more than doubled, which is one of the targets of the Swiss energy policy. The supply chains for the different types of fuel wood are described and specifications and prices of log wood, forestry wood chips and wood residues are presented. The main applications of wood energy are residential heating with manually operated wood boilers and stoves, on the one hand, and heat production with automatic wood furnaces in industry and communities, on the other hand. Automatic furnaces have been promoted in the past ten years and hence they contribute nowadays with more than 50% to the energy supply from wood with a further growing share. As an assistance for further information, a list of institutions and addresses in the field of wood energy in Switzerland is given in the paper. (author)

  4. Universal shape evolution of particles by bed-load

    Science.gov (United States)

    Jerolmack, D. J.; Domokos, G.; Shaw, S.; Sipos, A.; Szabo, T.

    2016-12-01

    River currents, wind and waves drive bed-load transport, in which sediment particles collide with each other and the Earth's surface. A generic consequence is erosion and rounding of particles as a result of chipping, often referred to in geological literature as abrasion. Recent studies have shown that the erosion of river pebbles can be modeled as diffusion of surface curvature, indicating that geometric aspects of chipping erosion are insensitive to details of collisions and material properties. Here we present data from fluvial, aeolian and coastal environments that suggest a universal relation between particle circularity and mass lost due to bed-load chipping. Simulations and experiments support the diffusion model and demonstrate that three constraints are required to produce this universal curve: (i) initial particles are fragments; (ii) erosion is dominated by collisions among like-sized particles; and (iii) collision energy is small enough that chipping dominates over fragmentation. We show that the mechanics of bedrock weathering and bed-load transport select these constraints, providing the foundation to estimate a particle's erosion rate from its shape alone in most sedimentary environments. These findings may be used to determine the contribution of chipping to downstream fining in rivers and deserts, and to infer transport conditions using only images of sediment grains.

  5. Characterisation of wood combustion ashes

    DEFF Research Database (Denmark)

    Maresca, Alberto

    The combustion of wood chips and wood pellets for the production of renewable energy in Denmark increased from 5.7 PJ to 16 PJ during the period 2000-2015, and further increases are expected to occur within the coming years. In 2012, about 22,300 tonnes of wood ashes were generated in Denmark....... Currently, these ashes are mainly landfilled, despite Danish legislation allowing their application onto forest and agricultural soils for fertilising and/or liming purposes. During this PhD work, 16 wood ash samples generated at ten different Danish combustion plants were collected and characterised...... for their composition and leaching properties. Despite the relatively large variations in the contents of nutrients and trace metals, the overall levels were comparable to typical ranges reported in the literature for other wood combustion ashes, as well as with regards to leaching. In general, the composition...

  6. Demand and supply of wood fuels in the emission trade

    International Nuclear Information System (INIS)

    Ranta, T.; Lahtinen, P.; Laitila, J.

    2005-01-01

    The emission trade according to the EU directive on greenhouse gas emission allowance started at the beginning of the year 2005. This will boost the demand for wood fuels because of the addition-al value of CO 2 neutrality compared to fossil fuels. This bulletin covers the development of the demand and supply of wood fuels from 2002 to 2010 both at a national and a provincial level. The demand and supply balance of wood fuels will be evaluated both without the effect of emission trade and when the emission trade price level is 20 euro/ton- CO 2 for emission rights in 2010. The evaluations of fuel consumption for individual boilers were made with the help of the databases of Electrowatt-Ekono Ltd. The demand for wood fuels was estimated to double by the year 2010, being almost 50 TWh. The share of forest chips of the demand was one third, i.e. 17 TWh. The supply potential was divided into forest chips and solid by-products from forest industry. Forest chip sources included small diameter wood from young forests and logging residues and stumps from re-generation felling sites. The supply potential calculations of logging residues and stump biomass were based on databases of regeneration felling stands. The biomass potential from small diamreter wood was evaluated on the basis of field measurements of NFI 8 and 9 at a provincial level and multi-source data at a municipal level. In 2010, the supply potential of by-products was estimated to be 28 TWh of which 11 TWh was marketable out-side of the internal use of forest industry. Correspondingly, the theoretical potential of forest chips was estimated to be 51 TWh and the techno-economical potential 24 TWh. As a result of the regional optimization model, the energy use of wood fuels was 29 TWh, which was 59 % of the potential demand. In emission trade the demand was 33 TWh, which was 68 % of the potential demand. Regionally, the potential demand for wood fuels for energy use was higher than the supply in all provinces

  7. A look at worldwide usage of residual wood for energy

    International Nuclear Information System (INIS)

    Ekstrom, H.; Hall, M.M.

    2007-01-01

    Wood Resources International was established in 1987, offering on-site evaluation services of forest resources and forest industry developments in over 20 countries worldwide. This presentation reviewed residual wood markets in North America and Europe. Wood chip trade and wood pellet markets were also reviewed. It is estimated that more than 50 per cent of the wood harvested worldwide is used for heating and cooking. Although sawmill wood residue has been typically used for particle board manufacturing, the energy sector in North America and Europe is now competing for low cost residuals, including sawdust, shavings and wood chips. With demand for renewable resources increasing, district heating plants have revived an interest in collecting the nearly 35 per cent of biomass left behind after traditional clear cutting. This biomass represents branches, tops and stumps left behind after the roundwood has been removed. In Canada, demand for mill residuals has grown and wood pellet manufacturers have the opportunity to invest in capacity while continuing to produce competitively priced pellets for the European market. It is anticipated that in the next decade, large volumes of beetle-killed wood are going to be available in British Columbia for energy consumption, including wood pellet production. Prices for sawdust have doubled over the past 3 years as a result of increased competition. The biomass supply potential in the United States is 7 times the current consumption. There is an increased interest in bioenergy in California due to the declining lumber sector. As such, the use of forest and agricultural waste is on the rise, along with prices for wood residues. There has also been a large increase in demand for wood biomass in Europe over the past 5 years, resulting in higher costs of all wood fiber sources used for energy. By 2020, Europe has set a target that all energy should come from renewable energy sources, with a minimum of 10 per cent being biofuel for

  8. Phenolic Acids, Phenolic Aldehydes and Furanic Derivatives in Oak Chips: American vs. French Oaks

    OpenAIRE

    Cabrita, M.J.; Barrocas Dias, C.; Costa Freitas, A.M.

    2011-01-01

    Phenolic acids (gallic, vanillic, syringic and ellagic acids), phenolic aldehydes (vanillin, syringaldehyde, coniferaldehyde and sinapaldehyde) and furanic derivatives (furfural, 5-methylfurfural and 5-hydroxymethylfurfural) were quantified in commercial American and French oak chips. Chips with different sizes and toast degrees were used. Compounds were extracted directly from the wood samples in order to determine possible differences among woods as well as toast degree. Likewise, the compo...

  9. AFBnet - Wood and field energy information from Europe

    International Nuclear Information System (INIS)

    Alakangas, E.

    2001-01-01

    The objective of EU's ALTENER program is to promote the use of renewable energy sources. The European bioenergy network AFBnet produces and delivers information on bioenergy research and utilization of them in different countries. Import and export of biofuels, as well as the prices of biofuels in twenty European countries have been studied during past two years. The potential of combined heat and power generation with biofuels has also been estimated. The network has evaluated these projects and the factors, which have affected the successfulness and unsuccessfulness of the projects in different countries. In Finland the promotion of the utilization of wood fuels in municipal projects was evaluated in a 'Heat Entrepreneur competition' carried out first time in 2000. AFBnet analyzed the operation of 21 plants using mixed fuels as energy sources. One of the objectives was to collect information on experiences of production and processing phase of fuels at district heating and power plants in Finland, Italy, Austria, Portugal, Sweden, Germany and Denmark. The plants consumed different kinds of biofuels (industrial wood residues, straw and other agricultural wastes) and the mixture of them. Plants using different combustion technologies (grate, fluidized bed and pulverized fuel combustion, and biomass gasifiers). The consumption rate of wood and agricultural biofuels in plants was about 30% of the total fuel consumption. The main mixed fuel was coal, the share of which was 28% of the total. A detailed report has been published on all the plants. The reports analyze the fuel production and processing chains of the plants up to the boiler. Data was gathered also from the investments and maintenance costs of the plants. In EU countries there is no comprehensive survey on the prices of biofuels. Only Sweden publishes the prices of biofuels regularly. AFBnet collected in 1999 data on fuel prices, import and export of the fuels, and present utilization and potential of

  10. Natural drying treatments during seasonal storage of wood for bioenergy in different European locations

    International Nuclear Information System (INIS)

    Roeser, Dominik; Mola-Yudego, Blas; Sikanen, Lauri; Prinz, Robert; Gritten, David; Emer, Beatrice; Vaeaetaeinen, Kari; Erkkilae, Ari

    2011-01-01

    Research into the methods of producing high quality wood chips for a rapidly growing energy sector is becoming increasingly important. For example, small wood chip heating plants require high quality wood chips to ensure efficient operation, thereby minimizing maintenance costs. Moisture content is considered to be an important quality parameter regarding wood based fuels. The objective of this study is to investigate methods to promote the natural drying of wood for bioenergy purposes. The effects on the drying process through covering the wood piles and partial debarking of stems were tested in order to identify methods to reduce the moisture content of the woody material in the storage. Drying trials were established in Finland, Italy and Scotland, utilizing tree species typically used for energy purposes in each area. The results show that natural drying is a viable and effective method to enhance the energy efficiency of wood based fuel products in all the regions studied. Furthermore, by adapting current harvesting methods and storage procedures even better results can be achieved. In addition, the results also indicate that broadleaved trees dry more effectively, if some partial debarking is carried out and that covering of piles is of utmost importance in Scotland and Finland. -- Highlights: → Natural drying is an effective method to enhance efficiency in the wood-fuel chains → Broadleaved trees dry more effectively when partial debarking is done → In Scotland and Finland a method for covering of piles is of utmost importance.

  11. Bio-Oil Production from Fast Pyrolysis of Corn Wastes and Eucalyptus Wood in a Fluidized Bed Reactor

    Directory of Open Access Journals (Sweden)

    M.A Ebrahimi-Nik

    2014-09-01

    Full Text Available Fast pyrolysis is an attractive technology for biomass conversion, from which bio-oil is the preferred product with a great potential for use in industry and transport. Corn wastes (cob and stover and eucalyptus wood are widely being produced throughout the world. In this study, fast pyrolysis of these two materials were examined under the temperature of 500 °C; career gas flow rate of 660 l h-1; particle size of 1-2 mm; 80 and 110 g h-1 of feed rate. The experiments were carried out in a continuous fluidized bed reactor. Pyrolysis vapor was condensed in 3 cooling traps (15, 0 and -40 °C plus an electrostatic one. Eucalyptus wood was pyrolyised to 12.4, 61.4, and 26.2 percent of bio-char, bio-oil and gas, respectively while these figures were as 20.15, 49.9, and 29.95 for corn wastes. In all experiments, the bio-oil obtained from electrostatic trap was a dark brown and highly viscose liquid.

  12. Energy wood resources availability and delivery cost in Northwest Russia

    Energy Technology Data Exchange (ETDEWEB)

    Gerasimov, Yuri; Karjalainen, Timo [Finnish Forest Research Inst., Joensuu (Finland)], E-mail: yuri.gerasimov@metla.fi

    2013-10-01

    Availability of solid by-products from wood harvesting and mechanical wood processing was estimated as sources for energy production based on recent actual harvesting, sawmill, and plywood production in Northwest Russia at 30 million m{sup 3}. Nearly 70% of the energy wood, 20 million m{sup 3}, was from harvesting, consisting of non-industrial round wood, unused branches and tops, defective wood resulting from logging, and spruce stumps removed after final felling. Over 30%, 10 million m{sup 3}, of the available volume was from sawmills and plywood mills, i.e. wood chips, sawdust, and bark. Due to current low utilization of energy wood for bioenergy in Northwest Russia, delivery cost of energy wood to the potential border-crossing points in Finland was analyzed for three means of transport: railways, roadways, and waterways. Nearly 28 million m{sup 3} of the energy wood could be transported by railways and 2 million m{sup 3} by roadways and waterways. The costs were lowest by roadways from the nearby border areas (10-15 Euro/m{sup 3} for wood processing by-products and 16-22 Euro/m{sup 3} for forest chips). The costs by railways varied from 12 to 27 Euro/m{sup 3} on shorter distances to 47-58 Euro/m{sup 3} on longer distances. Waterway transportation was the most expensive, about 28-48 Euro/m{sup 3}. It should be emphasized that we have estimated availability and delivery costs of energy wood, not prices which are defined by the market based on supply and demand.

  13. Power generation using coir-pith and wood derived producer gas in diesel engines

    Energy Technology Data Exchange (ETDEWEB)

    Ramadhas, A.S.; Jayaraj, S.; Muraleedharan, C. [Department of Mechanical Engineering, National Institute of Technology Calicut, Calicut-673 601, Kerala State (India)

    2006-10-15

    Partial combustion of biomass in the gasifier generates producer gas that can be used for heating purposes and as supplementary or sole fuel in internal combustion engines. In this study, the potential of coir-pith and wood chips as the feedstock for gasifier is analyzed. The performance of the gasifier-engine system is analyzed by running the engine for various producer gas-air flow ratios and at different load conditions. The system is experimentally optimized with respect to maximum diesel savings and lower emissions in the dual fuel mode operation while using coir-pith and wood chips separately. The performance and emission characteristics of the dual fuel engine are compared with that of diesel engine at different load conditions. Specific energy consumption in the dual fuel mode of operation is found to be in the higher side at all load conditions. The brake thermal efficiency of the engine while using wood chips in the dual mode operation is higher than that of coir-pith. The CO emission is higher in the case of dual fuel mode of operation as compared to that of diesel mode. In the dual fuel mode of operation, the higher diesel savings is achieved while using wood chips as compared to that of coir-pith. The comparison of the performance and emission characteristics of the dual fuel engine with diesel engine is also described. (author)

  14. Energy wood. Part 2b: Wood pellets and pellet space-heating systems; Holzenergie Teil 2b: Holzpellets und Pelletheizungen / Energie du bois Partie 2b: Granules de bois et installations de chauffage a granules de bois

    Energy Technology Data Exchange (ETDEWEB)

    Nussbaumer, T. [Verenum, Zuerich (Switzerland)

    2002-07-01

    The paper gives an overview on pellet utilization including all relevant process steps: Potential and properties of saw dust as raw material, pellet production with drying and pelletizing, standardization of wood pellets, storage and handling of pellets, combustion of wood pellets in stoves and boilers and applications for residential heating. In comparison to other wood fuels, wood pellets show several advantages: Low water content and high heating value, high energy density, and homogeneous properties thus enabling stationary combustion conditions. However, quality control is needed to ensure constant properties of the pellets and to avoid the utilization of contaminated raw materials for the pellet production. Typical data of efficiencies and emissions of pellet stoves and boilers are given and a life cycle analysis (LCA) of wood pellets in comparison to log wood and wood chips is described. The LCA shows that wood pellets are advantageous thanks to relatively low emissions. Hence, the utilization of wood pellet is proposed as a complementary technology to the combustion of wood chips and log wood. Finally, typical fuel cost of wood pellets in Switzerland are given and compared with light fuel oil. (author)

  15. Wood harvesting as chunkwood chips and multi-stage chipping; Puun korjuu palahakkeena ja monivaiheinen lastuaminen

    Energy Technology Data Exchange (ETDEWEB)

    Kaipainen, H; Seppaenen, V

    1997-12-31

    The task for the year 1995 was to define the preliminary results of the previous years, to measure the productivity of a harvester, designed for production of chunkwood, and the properties of the chunks. The costs of the PALAPUU method from the felling site to pulpwood chips were to be examined on this basis. Because the prototype of the harvester was not yet available for field tests, the costs were partially calculated on the basis of previous measurements, completed by productivity data obtained from the time-consumption measurements of a multi-tree harvester, applied with minor alteration for this purpose. According to the calculations the PALAPUU method cannot compete with partial-tree or shortwood methods. The profitability of the method could be improved by adding the transportation density and the productivity of the harvester. It is also possible to procure timber to the mill as partial-trees and to chunk it while feeding it into the drum. Chipping tests were made using the steel-frame-chipper owned by VTT Construction Technology. The blade construction of the chipper was changed so, that it was possible to adjust the cutting thickness of the chips to 4 mm, while in the previous mill-tests it had been 6 mm. The chips were used for cooking tests in the Department of Chemistry of the University of Jyvaeskylae. The results showed that the thinner chips were cooked further under the same cooking conditions. By using the chunkwood method it is possible to harvest 10-70 more biomass for the mills, than it is possible in the pulpwood harvesting

  16. Wood harvesting as chunkwood chips and multi-stage chipping; Puun korjuu palahakkeena ja monivaiheinen lastuaminen

    Energy Technology Data Exchange (ETDEWEB)

    Kaipainen, H.; Seppaenen, V.

    1996-12-31

    The task for the year 1995 was to define the preliminary results of the previous years, to measure the productivity of a harvester, designed for production of chunkwood, and the properties of the chunks. The costs of the PALAPUU method from the felling site to pulpwood chips were to be examined on this basis. Because the prototype of the harvester was not yet available for field tests, the costs were partially calculated on the basis of previous measurements, completed by productivity data obtained from the time-consumption measurements of a multi-tree harvester, applied with minor alteration for this purpose. According to the calculations the PALAPUU method cannot compete with partial-tree or shortwood methods. The profitability of the method could be improved by adding the transportation density and the productivity of the harvester. It is also possible to procure timber to the mill as partial-trees and to chunk it while feeding it into the drum. Chipping tests were made using the steel-frame-chipper owned by VTT Construction Technology. The blade construction of the chipper was changed so, that it was possible to adjust the cutting thickness of the chips to 4 mm, while in the previous mill-tests it had been 6 mm. The chips were used for cooking tests in the Department of Chemistry of the University of Jyvaeskylae. The results showed that the thinner chips were cooked further under the same cooking conditions. By using the chunkwood method it is possible to harvest 10-70 more biomass for the mills, than it is possible in the pulpwood harvesting

  17. Energy use of decayed wood; Lahopuun maeaerae, sisaeltoe ja hankintakustannukset

    Energy Technology Data Exchange (ETDEWEB)

    Maekelae, M; Lipponen, K [Metsaeteho Oy, Helsinki (Finland)

    1997-12-01

    A study of the quality, amounts and delivery costs of decayed wood available for possible energy use will be carried out in co-operation by Metsaeteho and Forest Research Institute. The work will consist of the following sub-studies: Quality of decayed wood available for possible energy use, quantities of decayed wood available for possible energy use by municipalities in Western and Southern Finland, harvesting, transport and chipping costs of decayed wood in different delivery alternatives and as a practical example, quantities of decayed wood available for possible energy use in two potential consumption municipalities. (orig.)

  18. Evaluation of sludge from paper recycling as bedding material for broilers.

    Science.gov (United States)

    Villagrá, A; Olivas, I; Benitez, V; Lainez, M

    2011-05-01

    Several materials have been used as bedding substrates in broiler production. In this work, the sludge from paper recycling was tested for its potential use as litter material and was compared with wood shavings. Moisture content, apparent density, and water-holding capacity were measured and characterized in both materials. Later, 192 male broiler chickens were distributed among 16 experimental pens, 8 of which contained wood shavings as bedding material and 8 of which contained the sludge. Growth rate, consumption, tonic immobility, gait score, breast lesions, foot pad dermatitis, hock burn, tibial dyschondroplasia, and metatarsal thickness were determined in the birds. Although the moisture content of the sludge was high, it decreased strongly after 7 d of drying, reaching lower values than those of wood shavings. In general, few differences were found between the materials in terms of bird performance and welfare and only the incidence of hock burn was higher in the sludge than in the wood shavings. Although further research is needed, sludge from paper recycling is a possible alternative to traditional bedding materials because it achieves most of the requirements for broiler bedding materials and does not show negative effects on the birds.

  19. Wood for energy production. Technology - environment - economy

    International Nuclear Information System (INIS)

    Serup, H.; Falster, H.; Gamborg, C.

    1999-01-01

    'Wood for Energy Production', 2nd edition, is a readily understood guide to the application of wood in the Danish energy supply. The first edition was named 'Wood Chips for Energy Production'. It describes the wood fuel from forest to consumer and provides a concise introduction to technological, environmental, and financial matters concerning heating systems for farms, institutions, district heating plants, and CHP plants. The individual sections deal with both conventional, well known technology, as well as the most recent technological advances in the field of CHP production. The purpose of this publication is to reach the largest possible audiance, and it is designed so that the layman may find its background information of special relevance. 'Wood for Energy Production' is also available in German and Danish. (au)

  20. Wood for energy production. Technology - environment - economy

    Energy Technology Data Exchange (ETDEWEB)

    Serup, H.; Falster, H.; Gamborg, C. [and others

    1999-10-01

    `Wood for Energy Production`, 2nd edition, is a readily understood guide to the application of wood in the Danish energy supply. The first edition was named `Wood Chips for Energy Production`. It describes the wood fuel from forest to consumer and provides a concise introduction to technological, environmental, and financial matters concerning heating systems for farms, institutions, district heating plants, and CHP plants. The individual sections deal with both conventional, well known technology, as well as the most recent technological advances in the field of CHP production. The purpose of this publication is to reach the largest possible audiance, and it is designed so that the layman may find its background information of special relevance. `Wood for Energy Production` is also available in German and Danish. (au)

  1. Assessment of Large Wood budget in the gravel-bed Piave River: first attempt

    Science.gov (United States)

    Tonon, Alessia; Picco, Lorenzo; Ravazzolo, Diego; Aristide Lenzi, Mario

    2015-04-01

    During the last decades, the dynamics of large wood (LW) in rivers were analyzed to consider and define the LW budget. The space-time variations of LW amount results from the differences among input (e.g. fluvial transport, lateral recruitment) and output (e.g. fluvial transport, overbank deposition, natural chronic dead) of LW along a riverine environment. Different methodologies were applied in several fluvial environments, however in large river systems characterized by complex LW dynamics, the processes are still poor quantified. Aim of this contribution is to perform a LW budget estimation over the short period, assessing the effect of an over bankfull flood (Q=1039 m3 s-1; R.I=3.5 years). The research was carried out along a 1 km-long reach (around 15 ha) located into the middle course of the large gravel-bed Piave River (North East of Italy). The LW budget has been defined considering the recruitment through bank erosion and the fluvial transport of LW into and out of the study reach. The former factor was achieved integrating field data on riparian vegetation with the monitoring of riverbanks with a Differential Global Positioning System (DGPS). The latter was obtained detecting all LW elements (diameter ≥ 0.10 m and/or length ≥ 1 m) stored along the study reach, before and after the flood. For each LW the GPS position was recorded and a numbered tag was installed with the addition of colored paint to permit a rapid post-event recovery. Preliminary results indicate that, along the study area, the floating transport of LW is one of the most significant processes able to modify the amount of LW deposited along a riverine system. In fact, considering the input of LW, the 99.4 % (102 m3 km-1) comes from upstream due to floating, whereas the 0.6% (0.17 m3 km-1) was recruited through bank erosion. Analyzing the output, 94.3% (40.26 m3 km-1) of LW was transported downstream of the study area, whereas only the 5.7 % (2.43 m3 km-1) of LW was involved in the

  2. Conversion of forest residues to a clean gas for fuel or synthesis

    Energy Technology Data Exchange (ETDEWEB)

    Feldmann, H.F.; Liu, K.T.; Longanbach, J.R.; Curran, L.M.; Chauhan, S.P.

    1979-01-01

    A program is described for developing a gasification system specifically for wood and other biomass materials which allows greatly increased gasifier throughputs and direct catalysis of wood. Wood ash, which is a by-product of a wood gasification plant, can be used as a gasification catalyst for wood, as it increases gasification rates and promotes the water-gas shift reaction. The high reactivity of even uncatalyzed biomass allows the potential of very high gasifier throughputs. However, the achievement of this potential requires that the gasifier operate at gas velocities higher than those attainable in conventional reactor systems. Stable and very smooth fluidization with uniform mixing and distribution of chips throughout the bed was observed on addition of an entrained sand phase to a fluidized bed of alumina and wood chips. Economc feasibility studies based on utilization of a proprietary Battelle gasification system which utilizes an entrained-phase heat carrier indicated that an intermediate-Btu gas can be produced in 1000 ton/day plants at a price competitive with liquefied natural gas and No. 2 heating oil.

  3. Interactive Effects of Climate Change and Decomposer Communities on the Stabilization of Wood-Derived Carbon Pools: Catalyst for a New Study

    Energy Technology Data Exchange (ETDEWEB)

    Resh, Sigrid C. [Michigan Technological Univ., Houghton, MI (United States)

    2014-11-17

    Globally, forest soils store ~two-thirds as much carbon (C) as the atmosphere. Although wood makes up the majority of forest biomass, the importance of wood contributions to soil C pools is unknown. Even with recent advances in the mechanistic understanding of soil processes, integrative studies tracing C input pathways and biological fluxes within and from soils are lacking. Therefore, our research objectives were to assess the impact of different fungal decay pathways (i.e., white-rot versus brown-rot)—in interaction with wood quality, soil temperature, wood location (i.e., soil surface and buried in mineral soil), and soil texture—on the transformation of woody material into soil CO2 efflux, dissolved organic carbon (DOC), and soil C pools. The use of 13C-depleted woody biomass harvested from the Rhinelander, WI free-air carbon dioxide enrichment (Aspen-FACE) experiment affords the unique opportunity to distinguish the wood-derived C from other soil C fluxes and pools. We established 168 treatment plots across six field sites (three sand and three loam textured soil). Treatment plots consisted of full-factorial design with the following treatments: 1. Wood chips from elevated CO2, elevated CO2 + O3, or ambient atmosphere AspenFACE treatments; 2. Inoculated with white rot (Bjerkandera adusta) or brown rot (Gloeophyllum sepiarium) pure fungal cultures, or the original suite of endemic microbial community on the logs; and 3. Buried (15cm in soil as a proxy for coarse roots) or surface applied wood chips. We also created a warming treatment using open-topped, passive warming chambers on a subset of the above treatments. Control plots with no added wood (“no chip control”) were incorporated into the research design. Soils were sampled for initial δ13C values, CN concentrations, and bulk density. A subset of plots were instrumented with lysimeters for sampling soil water and temperature data

  4. Force Relations and Dynamics of Cutting Knife in a Vertical Disc Mobile Wood Chipper

    Directory of Open Access Journals (Sweden)

    Segun R. BELLO

    2011-06-01

    Full Text Available The force relations and dynamics of cutting knife in a vertical disc wood chipper were investigated. The tool geometry determined include: rake angle (20 deg C; Shear angle, (fi= 52.15 deg C; the mean frictional angle, (t = 5.71 deg C. The analysis and comparison of the cutting forces has shown that the chips separated from the wood are being formed by off cutting, since normal applied force N is compressive in nature, the magnitude of the forces used by the knife on the wood is expected to increase as the cutting edge of the knife goes deeper into the wood until the value of the resisting force acting against the cut wood Ff is reached and exceeded. The evaluated forces acting on the knife and the chip are: F = 3.63Nmm^-1; N = 34.7 Nmm^-1; Fs= 27.45Nmm^-1; Fn =31.92 Nmm^-1; Ft = -8.46Nmm^-1; Fc = 33.85Nmm^-1. The resultant force acting on the tool face, Pr = 34.89Nmm^-1. The specific cutting pressure, Pc and cutting force needed to cut the timber, Fc, are 1.79 × 10^6 N/m2 and 644.84N respectively. The energy consumed in removing a unit volume of material is 69.96kJ/mm^-3 and the maximum power developed in cutting the chip is 3591.77W (4.82hp. The chipper efficiency (86.6% was evaluated by the highest percentage of accepted chip sizes.

  5. Physical Damages of Wood Fiber in Acacia Mangium due to Biopulping Treatment

    Directory of Open Access Journals (Sweden)

    Ridwan Yahya

    2016-05-01

    chrysosporium to Acacia mangium Willd can reduce lignin and improve holocellulose and cellulose content of the material. Fiber dimension recognized as other important factor for paper properties. The question is how the integrity and dimensions of the wood fiber that has been pretreated with the fungus. The objectives of present study were to know effect of pretreatment of P. chrysosporium to the integrity and dimensions of the fiber. The P. chrysosporium was cultured for 14 days in growth medium, and inoculated to wood chips 5% (w/v and incubated for 0, 15 and 30 days. The inoculated wood chips were chipped into 1 mm x 1 mm x 20 mm and macerated using franklin solution at 60 oC for 48 hours. Forty fibers from each incubated time were analized their physical damages using a light microscope at a 400 magnification. The inoculated fibers were measured theirs dimensions. The physical damage percentage of fibers pretreated using P. chrysosporium was 0%. Length and wall thickness of the pretreated fibers were can be categorized as middle class and thin fibers, respectively.

  6. Integrated production method for wood fuel and pulp wood in Northern Finland; Integroitu energiapuun tuotanto-menetelmae Pohjois-Suomessa

    Energy Technology Data Exchange (ETDEWEB)

    Hooli, A [Hooli Oy, Kemi (Finland); Ranta, T [VTT Energy, Jyvaeskylae (Finland)

    1997-12-01

    Hooli Oy, operating mainly in the Northern Finland has developed the production method suitable for bunch-processing of small wood. The mobile machine, consisting of delimber-debarker, and fuel fraction crusher units, produces debarked stemwood for pulping industry and branchwood-bark chips for thermal power stations. The basic method has been ready for demonstration and practical applications since in the beginning of year 1996. The objective of the project is to develop a method suitable for bundle processing of small wood, in which the trees are delimbed and debarked, and the formed waste wood is crushed using a machine unit, developed especially for this purpose. The method is based on utilisation of a separate delimbing-debarking unit, which operates separately from the pulpwood transportation chain, so the pulpwood transportations can be done at the proper time either as debarked roundwood or chips. Based on field experiments in 1995 - 1996, to attain the targets of the project looks promising. In 1997 there will happen technical modifications to the machine to improve the debarking results (target < 1 % bark content) of the bolts and to improve the logistic productivity of the whole production chain

  7. Economy of wood supply

    International Nuclear Information System (INIS)

    Imponen, V.

    1993-01-01

    Research and development of wood fuels production was vigorous in the beginning of the 1980's. Techniques and working methods used in combined harvesting and transportation of energy and merchantable wood were developed in addition to separate energy wood delivery. After a ten year silent period the research on this field was started again. At present the underutilization of forest supplies and the environmental effects of energy production based on fossil fuels caused the rebeginning of the research. One alternative for reduction of the price of wood fuels at the utilization site is the integration of energy and merchantable wood deliveries together. Hence the harvesting and transportation devices can be operated effectively, and the organizational costs are decreased as well. The wood delivery costs consist of the stumpage price, the harvesting and transportation costs, and of general expenses. The stumpage price form the largest cost category (over 50 %) of the industrial merchantable wood delivery, and the harvesting and transportation costs in the case of thinningwood delivery. Forest transportation is the largest part of the delivery costs of logging residues. The general expenses, consisting of the management costs and the interest costs of the capital bound to the storages, form a remarkable cost category in delivery of low-rank wood for energy or conversion purposes. The costs caused by the harvesting of thinningwood, the logging residues, chipping and crushing, the lorry transportation are reviewed in this presentation

  8. Wood for energy production. Technology - environment - economy[Denmark

    Energy Technology Data Exchange (ETDEWEB)

    Serup, H.; Falster, H.; Gamborg, C. [and others

    1999-07-01

    'Wood for Energy Production', 2nd edition, is a readily understood guide to the application of wood in the Danish energy supply. The first edition was named 'Wood Chips for Energy Production'. It describes the wood fuel from forest to consumer and provides a concise introduction to technological, environmental, and financial matters concerning heating systems for farms, institutions, district heating plants, and CHP plants. The individual sections deal with both conventional, well known technology, as well as the most recent technological advances in the field of CHP production. The purpose of this publication is to reach the largest possible audiance, and it is designed so that the layman may find its background information of special relevance. 'Wood for Energy Production' is also available in German and Danish. (au)

  9. Performance of copper-based wood preservatives in soil bed exposures

    Science.gov (United States)

    Stan T. Lebow; Thomas Nilsson; Jeffrey J. Morrell

    Copper-based biocides are widely used to protect wood from biological attack in a variety of environments. Chromated copper arsenate (CCA) is the dominant copper-based preservative for wood protection (J. T. MICKLEWRIGHT, 1989). First developed in India in the 1930s, CCA contains a very effective combination of materials. Copper provides protection against most...

  10. Fuel-wood from undermanaged woodland

    Energy Technology Data Exchange (ETDEWEB)

    Landen, R A

    1995-11-22

    This report examines the potential for the utilisation of currently undermanaged woodland for supply of wood fuel. The potential markets for wood fuel are identified, along with their requirements in terms of fuel specification. Woodland resources currently receiving little or no management are identified, concentrating on broadleaves in lowland Britain. The nature of these resources is discussed, and opportunities/constraints for their management reviewed. Machinery suitable for these woodland areas is discussed, and the application of this equipment into practical systems is examined in some detail. These themes are developed in two case studies, resulting in a discussion of findings and a range of conclusions. It is believed that potential exists to extract chipped wood fuel form existing unmanaged woodland areas from Pound 25/gt upwards, including standing value and contractor profit. (Author)

  11. Corrosivity of hot flue gases in the fluidized bed combustion of recovered waste wood

    Energy Technology Data Exchange (ETDEWEB)

    Enestam, S.

    2011-07-01

    In recent years, recovered waste wood has become a fuel of interest due to its green energy benefits and low price compared to virgin wood-based fuels. However, waste wood is often contaminated with paint, plastic, and metal components, producing concentrations of heavy metals such as zinc and lead, chlorine, sodium, and sometimes sulphur that are elevated relative to those in virgin wood. In several cases, boilers burning waste wood have experienced increased fouling and corrosion of furnace walls, superheaters, and economizers, problems associated with chlorine, zinc, lead, and alkali metals in the deposits. The location of the deposits and the corrosion as well as the composition of the deposits vary with the fuel composition, boiler design, combustion parameters, flue gas temperature, and material temperature. Experience gained from the operation of biofuel and waste boilers shows that corrosion damage can be reduced, or even avoided, by the selection of optimum materials or for heat exchanger surfaces, by the use of fuel mixtures or additives that decrease the corrosivity of the combustion environment, by the placement of superheaters in a less corrosive environment, and by adjusting the steam parameters. Finding the right solutions for boilers burning RWW requires a thorough understanding of the whole process, including the fuel fed into the boiler, the combustion atmosphere, the corrosivity of the flue gas and the deposits, and the corrosion resistance of different boiler materials under the prevailing conditions. The objective of this work was to shed more light on the combustion environment in bubbling fluidized bed boilers burning RWW and thus increase knowledge about the corrosivity of zinc- and lead-rich deposits formed during the combustion of RWW, with the final goal of developing a corrosion prediction tool for use in the design of boilers for RWW combustion. With such a tool, it would be possible to optimize boiler design and material selection with

  12. About the gasification of untreated scrap and waste wood in fluidized bed reactor for use in decentralized gas engine-cogeneration plants; Zur Vergasung von Rest- und Abfallholz in Wirbelschichtreaktoren fuer dezentrale Energieversorgungsanlagen

    Energy Technology Data Exchange (ETDEWEB)

    Tepper, H.

    2005-10-20

    This dissertation examines the thermochemical conversion (gasification) of untreated scrap and waste wood in combustible gases for use in decentralized gas engine-cogeneration plants of low output (1 to 10 MW fuel power). A general section goes into the basics of the energetic utilization of solid biomass, the subprocesses of thermochemical conversion being described in more detail. Special attention is given to the processes and state of the art of biomass gasification in decentralized plants. A theoretical section analyzes the gasification models for solid biomass presented in the literature. Based on this analysis, a simplified kinetic model is derived for the gasification of untreated scrap and waste wood with air in bubbling fluidized bed reactors. It includes a fluid mechanic analysis of the fluidized bed based on HILLIGARDT, an empirical pyrolysis model and a global kinetic approach to the main chemical reaction taken from the literature. An experimental section describes the tests of the gasification of forest scrap wood in a semi-industrial fluidized bed gasification test plant with 150 kW fuel power and presents the significant test results. The gasification model derived is applied to check the test plant's standard settings and compare them with measured values. Furthermore, the model is employed to explain basic reaction paths and zones and to perform concluding parameter simulations. (orig.)

  13. Fungal bio-treatment of spruce wood with Trametes versicolor for pitch control: Influence on extractive contents, pulping process parameters, paper quality and effluent toxicity

    NARCIS (Netherlands)

    Beek, van T.A.; Kuster, B.; Claassen, F.W.; Tienvieri, T.; Bertaud, F.; Lennon, G.; Petit-Concil, M.; Sierra-Alvarez, R.

    2007-01-01

    Lipophilic low molar-mass constituents in wood chips for the paper industry result in low quality pulp, pitch deposition, and effluent toxicity. New biotechnological solutions such as fungal pre-treatment of wood chips can reduce pitch problems. This laboratory-scale study focuses on the potential

  14. Ethanol production from residual wood chips of cellulose industry: acid pretreatment investigation, hemicellulosic hydrolysate fermentation, and remaining solid fraction fermentation by SSF process.

    Science.gov (United States)

    Silva, Neumara Luci Conceição; Betancur, Gabriel Jaime Vargas; Vasquez, Mariana Peñuela; Gomes, Edelvio de Barros; Pereira, Nei

    2011-04-01

    Current research indicates the ethanol fuel production from lignocellulosic materials, such as residual wood chips from the cellulose industry, as new emerging technology. This work aimed at evaluating the ethanol production from hemicellulose of eucalyptus chips by diluted acid pretreatment and the subsequent fermentation of the generated hydrolysate by a flocculating strain of Pichia stipitis. The remaining solid fraction generated after pretreatment was subjected to enzymatic hydrolysis, which was carried out simultaneously with glucose fermentation [saccharification and fermentation (SSF) process] using a strain of Saccharomyces cerevisiae. The acid pretreatment was evaluated using a central composite design for sulfuric acid concentration (1.0-4.0 v/v) and solid to liquid ratio (1:2-1:4, grams to milliliter) as independent variables. A maximum xylose concentration of 50 g/L was obtained in the hemicellulosic hydrolysate. The fermentation of hemicellulosic hydrolysate and the SSF process were performed in bioreactors and the final ethanol concentrations of 15.3 g/L and 28.7 g/L were obtained, respectively.

  15. Hydrothermal pretreatment of wood by mild steam explosion and hot water extraction.

    Science.gov (United States)

    Wojtasz-Mucha, Joanna; Hasani, Merima; Theliander, Hans

    2017-10-01

    The aim of this work was to compare the two most common hydrothermal pre-treatments for wood - mild steam explosion and hot water extraction - both with the prospect of enabling extraction of hemicelluloses and facilitating further processing. Although both involve autohydrolysis of the lignocellulosic tissue, they are performed under different conditions: the most prominent difference is the rapid, disintegrating, discharge employed in the steam explosion opening up the structure. In this comparative study, the emphasis was placed on local composition of the pre-treated wood chips (of industrially relevant size). The results show that short hot water extraction treatments lead to significant variations in the local composition within the wood chips, while steam explosion accomplishes a comparably more even removal of hemicelluloses due to the advective mass transport during the explosion step. Copyright © 2017 Elsevier Ltd. All rights reserved.

  16. Activity concentrations of radionuclides in energy production from peat, wood chips and straw

    International Nuclear Information System (INIS)

    Hedvall, R.

    1997-04-01

    In this thesis quantitative analyses of radionuclide concentrations in bioenergy fuels such as peat, wood chips and straw are presented. For comparison a brief description is included of radionuclide concentrations and radiation doses from other sources of power and also from some industrial applications. Radioactive potassium is found in most materials and is the most easily detected radionuclide in fuels. It's activity concentration in Bq/kg normally dominates over the concentration of other natural radionuclides. The radiation dose from K in emission from combustion is nevertheless negligible. The most important radionuclides in the dose to man are the U- and Th-isotopes and 210 Pb and 210 Po. 137 Cs is the most common nuclide among the fission products in fallout from the Chernobyl accident. Compared to natural nuclides, the contribution from emission of 137 Cs is less than a few percent of the total dose to the population. A total dose of approx. only a few μSv from inhalation can be calculated from the emission of a district heating plant in Sweden. This dose can be compared with the annual dose limit to the public from nuclear industry, which is 0.1 mSv and the global collective effective dose of 5 manSv/year. 143 refs

  17. An Intelligent FPGA Based Anti-Sweating System for Bed Sore Prevention in a Clinical Environment

    Directory of Open Access Journals (Sweden)

    K. S. Jaichandar

    2011-01-01

    Full Text Available Bed sores, a common problem among immobile patients occur as a result of continuous sweating due to increase in skin to bed surface temperature in patients lying on same posture for prolonged period. If left untreated, the skin can break open and become infected. Currently adopted methods for bed sores prevention include: use of two hourly flip chat for repositioning patient or use of air fluidized beds. However, the setbacks of these preventive measures include either use of costly equipment or wastage of human resources. This paper introduces an intelligent low cost FPGA based anti-sweating system for bed sores prevention in a clinical environment. The developed system consists of bed surface implanted temperature sensors interfaced with an FPGA chip for sensing the temperature change in patient’s skin to bed surface. Based on the temperature change, the FPGA chip select the - mode (heater/cooler and speed of the fan module. Furthermore, an alarm module was implemented to alert the nurse to reposition the patient only if patient’s skin to bed surface temperature exceeds a predefined threshold thereby saving human resources. By integrating the whole system into a single FPGA chip, we were able to build a low cost compact system without sacrificing processing power and flexibility.

  18. Integrated production method for wood fuel and pulp wood in Northern Finland; Polttojakeen hankinta puun yhdistelmaekorjuussa ja integroitu energiapuun tuotantomenetelmae Pohjois-Suomessa

    Energy Technology Data Exchange (ETDEWEB)

    Hooli, A [Hooli Oy, Kemi (Finland); Kuitto, P J [VTT Energy, Jyvaeskylae (Finland); Ranta, T [Finntech Ltd. Oy, Jyvaeskylae (Finland)

    1997-12-31

    Chip production company Hooli Ltd. has built an innovative mobile chain-flail delimbing-debarking-unit which includes also a hammer crusher for wood fuel. This integrated production method for wood fuel and pulp wood based on that unit has been planned especially for the circumstances where the power or heating plants are near and the pulp mills more remote from the wood processing sites. The trees are felt into bunches and transported as whole trees or tree-sections to the roadside. The Hooli-unit delimbs and debarks the trees using multi-tree processing. The optimal bark content of Scot pine bolts after processing is under 1 %. All green branches, stops and bark are directly crushed into wood fuel in the same unit. Fuel chips are carried to the nearest power plant. The debarked bolts are transported to the pulpmills in the form of roundwood or pulpchips, thus giving better economy for the whole method. Based on first field experiments in 1995 this method has operated well. However, there are still development work ahead: e.g. good debarking quality of birch and spruce in the winter conditions. To attain the targets of the project looks promising. The project is carried out as joint project between Hooli Ltd, Finntech Ltd. Oy, the Finnish Forest Research Institute, Veitsiluoto Ltd and VTT Energy. The chain-flail delimbing-debarking-crushing unit was built at Tervolan Konepaja Ky

  19. Integrated production method for wood fuel and pulp wood in Northern Finland; Polttojakeen hankinta puun yhdistelmaekorjuussa ja integroitu energiapuun tuotantomenetelmae Pohjois-Suomessa

    Energy Technology Data Exchange (ETDEWEB)

    Hooli, A. [Hooli Oy, Kemi (Finland); Kuitto, P.J. [VTT Energy, Jyvaeskylae (Finland); Ranta, T. [Finntech Ltd. Oy, Jyvaeskylae (Finland)

    1996-12-31

    Chip production company Hooli Ltd. has built an innovative mobile chain-flail delimbing-debarking-unit which includes also a hammer crusher for wood fuel. This integrated production method for wood fuel and pulp wood based on that unit has been planned especially for the circumstances where the power or heating plants are near and the pulp mills more remote from the wood processing sites. The trees are felt into bunches and transported as whole trees or tree-sections to the roadside. The Hooli-unit delimbs and debarks the trees using multi-tree processing. The optimal bark content of Scot pine bolts after processing is under 1 %. All green branches, stops and bark are directly crushed into wood fuel in the same unit. Fuel chips are carried to the nearest power plant. The debarked bolts are transported to the pulpmills in the form of roundwood or pulpchips, thus giving better economy for the whole method. Based on first field experiments in 1995 this method has operated well. However, there are still development work ahead: e.g. good debarking quality of birch and spruce in the winter conditions. To attain the targets of the project looks promising. The project is carried out as joint project between Hooli Ltd, Finntech Ltd. Oy, the Finnish Forest Research Institute, Veitsiluoto Ltd and VTT Energy. The chain-flail delimbing-debarking-crushing unit was built at Tervolan Konepaja Ky

  20. Covering of milled peat stockpile with wood chips; Jyrsinturveauman peittaeminen hakkeella

    Energy Technology Data Exchange (ETDEWEB)

    Franssila, T.; Leinonen, A.

    1996-12-31

    The aim of this project is to research the applicability of wooden materials for protection of milled peat stockpile against losses during storaging. Water transmission features of sawdust, wastewood chip and whole tree chip were investigated in laboratory with raining experiments. The plan for raining experiments was made with experiment planning program and results were analysed with multivariate analysis. Freezing features were investigated thorough breaking tests with hydraulic piston vice. Laboratory experiments were completed with field tests in Laakasuo near Sotkamo. On the basis of results covering peat stockpiles with sawdust is fully competitive comparing to present covering methods. Chip materials are technically not as good covering materials as sawdust

  1. Understanding wood chemistry changes during biopulping

    Science.gov (United States)

    Chris Hunt; William Kenealy; Carl Houtman

    2003-01-01

    Biopulping is the process of pretreating chips with fungus before mechanical pulping, resulting in significant energy savings and sheet strength improvements. This work presents sugar analysis, methylene blue adsorption, and titration data suggesting an increase in acid group content in wood is common with biopulping treatment. Some discussion of possible mechanisms of...

  2. Proceedings of the 8. biennial residual wood conference

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2009-07-01

    This conference highlighted practical strategies for managing and utilizing residual wood as a true industry resource. Examples of successful wood energy projects were presented along with the technology and products of more than 30 companies involved in the residual wood business. The topics of discussion ranged from biomass supplies, quality issues, and harvesting guidelines to emerging biomass technologies, project overviews, and financing. The presentations outlined the many opportunities that exist for the forest industry to produce energy from biostock, such as healthy and diseased trees, underbrush, sawdust, wood chips, wood pulp and black liquor. Increasing fuel and energy costs along with advances in technology are improving the economy of forest-based biorefineries. The presentations showed how the industry can gain revenue from residual wood, which is steadily becoming a more valuable resource for pellet production and energy generation The conference featured 20 presentations, of which 3 have been catalogued separately for inclusion in this database. refs., tabs., figs.

  3. Integrated production of wood fuel and pulp wood from young stands; Integroitujen tuotantomenetelmien vertailu

    Energy Technology Data Exchange (ETDEWEB)

    Korpilahti, A [Metsaeteho Oy, Helsinki (Finland)

    1997-12-01

    The aim of the study was to clarify the competitiveness of different harvesting chains and processing methods of first thinning wood. Great expectations have been laid on integrated production of wood fuel and pulp wood. Results produced in other bioenergy projects were taken into account, and in this project some field experiments on mechanised felling-bunching and compressing of the load of tree sections during forwarding were carried out. The new processing methods, the MASSAHAKE-method and chain-flail delimbing combined with small-scale drum debarking, still are under development giving a rather unstable data for comparisons. Both in pine and birch dominant stands modern multiple tree logging gave the most favourable results when ranking on the bases of the price of pulp chips. Integrated methods were not very far and they have more potential than methods based on harvesting delimbed short wood. When compared on the bases of the production cost of pulp, integrated methods were in general the most favourable because they give good subsidies on the form of bioenergy. (orig.)

  4. Supply chain cost analysis of long-distance transportation of energy wood in Finland

    International Nuclear Information System (INIS)

    Tahvanainen, Timo; Anttila, Perttu

    2011-01-01

    The increasing use of bioenergy has resulted in a growing demand for long-distance transportation of energy wood. For both biofuels and traditional forest products, the importance of energy efficiency and rail use is growing. A GIS-based model for energy wood supply chains was created and used to simulate the costs for several supply chains in a study area in eastern Finland. Cost curves of ten supply chains for logging residues and full trees based on roadside, terminal and end-facility chipping were analyzed. The average procurement costs from forest to roadside storage were included. Railway transportation was compared to the most commonly used truck transportation options in long-distance transport. The potential for the development of supply chains was analyzed using a sensitivity analysis of 11 modified supply chain scenarios. For distances shorter than 60 km, truck transportation of loose residues and end-facility comminution was the most cost-competitive chain. Over longer distances, roadside chipping with chip truck transportation was the most cost-efficient option. When the transportation distance went from 135 to 165 km, depending on the fuel source, train-based transportation offered the lowest costs. The most cost-competitive alternative for long-distance transport included a combination of roadside chipping, truck transportation to the terminal and train transportation to the plant. Due to the low payload, the energy wood bundle chain with train transportation was not cost-competitive. Reduction of maximum truck weight increased the relative competitiveness of loose residue chains and train-based transportation, while reduction of fuel moisture increased competitiveness, especially of chip trucks.

  5. An assessment of management practices of wood and wood-related wastes in the urban environment

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-02-01

    The US Environmental Protection Agency estimates that yard waste{sup 1} accounts for approximately 16% of the municipal solid waste (MSW) stream (US EPA, 1994). Until recently, specific data and related information on this component of the (MSW) stream has been limited. The purposes of this study, phase two of the three-phase assessment of urban wood waste issues, are to assess and describe current alternatives to landfills for urban wood waste management; provide guidance on the management of urban wood waste to organizations that produce or manage wood waste; and clarify state regulatory and policy positions affecting these organizations. For this study, urban wood waste is defined as solid waste generated by tree and landscape maintenance services (public and private). Urban wood waste includes the following materials: unchipped mixed wood, unchipped logs, and unchipped tops and brush; clearing and grubbing waste; fall leaves and grass clippings; and chips and whole stumps. Construction and demolition debris and consumer-generated yard waste are not included in this study. Generators of urban wood waste include various organizations; municipal, county, and commercial tree care divisions; nurseries, orchards, and golf courses; municipal park and recreation departments; and electric and telephone utility power line maintenance, excavator and land clearance, and landscape organizations. (1) US EPA defines yard waste as ''yard trimmings'' which includes ''grass, leaves and tree brush trimmings from residential, institutional, and commercial sources.''

  6. Development of a modified equilibrium model for biomass pilot-scale fluidized bed gasifier performance predictions

    International Nuclear Information System (INIS)

    Rodriguez-Alejandro, David A.; Nam, Hyungseok; Maglinao, Amado L.; Capareda, Sergio C.; Aguilera-Alvarado, Alberto F.

    2016-01-01

    The objective of this work is to develop a thermodynamic model considering non-stoichiometric restrictions. The model validation was done from experimental works using a bench-scale fluidized bed gasifier with wood chips, dairy manure, and sorghum. The model was used for a further parametric study to predict the performance of a pilot-scale fluidized biomass gasifier. The Gibbs free energy minimization was applied to the modified equilibrium model considering a heat loss to the surroundings, carbon efficiency, and two non-equilibrium factors based on empirical correlations of ER and gasification temperature. The model was in a good agreement with RMS <4 for the produced gas. The parametric study ranges were 0.01 < ER < 0.99 and 500 °C < T < 900 °C to predict syngas concentrations and its LHV (lower heating value) for the optimization. Higher aromatics in tar were contained in WC gasification compared to manure gasification. A wood gasification tar simulation was produced to predict the amount of tars at specific conditions. The operating conditions for the highest quality syngas were reconciled experimentally with three biomass wastes using a fluidized bed gasifier. The thermodynamic model was used to predict the gasification performance at conditions beyond the actual operation. - Highlights: • Syngas from experimental gasification was used to create a non-equilibrium model. • Different types of biomass (HTS, DM, and WC) were used for gasification modelling. • Different tar compositions were identified with a simulation of tar yields. • The optimum operating conditions were found through the developed model.

  7. Fiber Recovery with Chain Flail Delimbing/Debarking and Chipping of Hybrid Poplar

    Science.gov (United States)

    Bruce Hartsough; Raffaele Spinelli; Steve Pottle; John Klepac

    2000-01-01

    This study determined how much wood was potentially available From short rotation hybrid poplar, and how mtich was actually recovered when trees were delimbed and debarked with chain flails and chipped. 3 1 groups of five trees each were measured and then processed. For trees larger than 50 kg total dry weight, potentially recoverable wood averaged 75% oftotal weight...

  8. Fuel gas production from renewable biomass in a circulating fluidized bed as a bases for zero-CO{sub 2} power generation in a combined-cycle power plant; Brenngaserzeugung aus nachwachsenden Biomassen in der zirkulierenden Wirbelschicht als Grundlage fuer eine CO{sub 2}-neutrale Stromerzeugung in einem GUD Kraftwerk

    Energy Technology Data Exchange (ETDEWEB)

    Albrecht, J; Loeffler, J; Hirschfelder, H [Lurgi Energie und Umwelt GmbH, Frankfurt am Main (Germany)

    1997-12-31

    A pilot circulating fluidized bed plant in the range of 1.7 MW{sub th} has been operated successfully with fossil fuels, residues, wood bark and wood chips, reet grass and sorghum pellets. Depending on the specifications for product gas and fuel quality, air, oxygen-enriched air or oxygen/steam mixtures are used as gasification agents in the gas generator. (orig) [Deutsch] In einer ZWS-Pilotanlage mit ca. 1.7 MW thermischer Leistung wurden bisher ausser fossilen und Abfallbrennstoffen auch Rindenabfaelle, Holzschnitzel, Schilfgras und Sorghumpellets erfolgreich zur Brenngaserzeugung eingesetzt. Entsprechend den Anforderungen an das Produktgas und der Brennstoffqualitaet wird Luft, sauerstoffangereicherte Luft oder Sauerstoff/Dampfgemische als Vergasungsmittel im ZWS-Gaserzeuger eingesetzt. (orig)

  9. Fuel gas production from renewable biomass in a circulating fluidized bed as a bases for zero-CO{sub 2} power generation in a combined-cycle power plant; Brenngaserzeugung aus nachwachsenden Biomassen in der zirkulierenden Wirbelschicht als Grundlage fuer eine CO{sub 2}-neutrale Stromerzeugung in einem GUD Kraftwerk

    Energy Technology Data Exchange (ETDEWEB)

    Albrecht, J.; Loeffler, J.; Hirschfelder, H. [Lurgi Energie und Umwelt GmbH, Frankfurt am Main (Germany)

    1996-12-31

    A pilot circulating fluidized bed plant in the range of 1.7 MW{sub th} has been operated successfully with fossil fuels, residues, wood bark and wood chips, reet grass and sorghum pellets. Depending on the specifications for product gas and fuel quality, air, oxygen-enriched air or oxygen/steam mixtures are used as gasification agents in the gas generator. (orig) [Deutsch] In einer ZWS-Pilotanlage mit ca. 1.7 MW thermischer Leistung wurden bisher ausser fossilen und Abfallbrennstoffen auch Rindenabfaelle, Holzschnitzel, Schilfgras und Sorghumpellets erfolgreich zur Brenngaserzeugung eingesetzt. Entsprechend den Anforderungen an das Produktgas und der Brennstoffqualitaet wird Luft, sauerstoffangereicherte Luft oder Sauerstoff/Dampfgemische als Vergasungsmittel im ZWS-Gaserzeuger eingesetzt. (orig)

  10. Gasification of Wood and Non-wood Waste of Timber Production as Perspectives for Development of Bioenergy

    Science.gov (United States)

    Kislukhina, Irina A.; Rybakova, Olga G.

    2018-03-01

    The article deals with biomass gasification technology using the gasification plant running on wood chips and pellets, produced from essential oils waste (waste of coniferous boughs). During the study, the authors solved the process task of improving the quality of the product gas derived from non-wood waste of timber production (coniferous boughs) due to the extraction of essential oils and the subsequent thermal processing of spent coniferous boughs at a temperature of 250-300°C degrees without oxygen immediately before pelleting. The paper provides the improved biomass gasification process scheme including the grinding of coniferous boughs, essential oil distillation and thermal treatment of coniferous boughs waste and pelletizing.

  11. Consumption of forest chips as an energy source as part of the national action plan for renewable energy

    International Nuclear Information System (INIS)

    Ylitalo, E.

    2004-01-01

    A specific Action Plan for Renewable Energy was introduced in 1999 in order to increase the utilisation of renewable energy sources in Finland. The Plan was renewed in 2002, taking into account a revision of the goals defined in the statements given by the Parliament in the de-bate on national Climate Strategy and the decision on building a new nuclear power plant. The main reason for increasing the consumption of renewable energy is the aim of decreasing emissions of greenhouse gases caused by fossil fuels. The renewed Action Plan includes aims and means of how to increase the consumption of renewable energy in practice in the future. Specific goals for separate renewable energy sources were set for the years 2005, 2010 and 2025. Proportional targets were set for the consumption of forest chips: in 2010 consumption is expected to be four times larger than in 2001 and in 2025 seven times larger. In Finland, the most important source for renewable energy is wood and wood waste, which currently makes up approximately 20 per cent of total energy consumption. Wood waste (incl. waste liquor and solid wood waste) produced by the forest industries can be considered as being fully utilized at the moment. Therefore, the most important means of increasing the consumption of wood energy in the future is in the utilisation of forest chips resources. Since 2000, the Finnish Forest Re-search Institute has compiled statistics on the consumption of forest chips and forest industry by-products used in energy generation. One aim of these statistics is to monitor the fruition of the Action Plan mentioned. In 2003, the volume of forest chips consumed in energy generation was 2.1 mill. m3, i.e. approximately five per cent of all energy sources consumed. According to the statistics, the consumption of forest chips has doubled during the period 2000-2003 with an annual average increase of 0.4 mill. m 3 . The goals set in the Action Plan can be considered to be high. In order to achieve

  12. Suitability of biocompost as a bedding material for stabled horses: respiratory hygiene and management practicalities.

    Science.gov (United States)

    Seedorf, J; Schröder, M; Köhler, L; Hartung, J

    2007-03-01

    Bedding material in stables has an important influence on air hygiene and information on the suitability of biocompost and wood shavings is incomplete. To compare the suitability and benefit of biocompost and wood shavings as bedding in horse stables and to determine key air factors for the evaluation of the potential impact of these materials on respiratory health. The study was conducted in a naturally ventilated stable with 4 horses. Air hygiene parameters were measured 24 h/day for 7 days with each bedding type: ammonia (NH3), inhalable and respirable dust, endotoxins, colony forming units (CFU) of total mesophilic bacteria, fungi, actinomycetes and thermophilic actinomycetes. Both bedding materials were analysed for general chemical composition, particle size distribution and natural microbial content. The animals' behaviour was monitored by video cameras, and their health and cleanliness status determined by clinical and visual examination. Concentrations of NH3, dust, endoxins and fungi were significantly higher during the monitoring period with wood shavings than with biocompost. In contrast concentrations of mesophilic bacteria, mesophilic actinomycetes and thermophilic actinomycetes microbial pollutants were highest with biocompost. The water content of bulk biocompost was considerably higher than that of wood shavings. Particles market.

  13. The concept of system for chips production need to work demo CHP plant in company 'AGROSAVA' from Šimanovci

    Directory of Open Access Journals (Sweden)

    Dedić Aleksandar Đ.

    2014-01-01

    Full Text Available In this paper according to the calculation of chips productivity needs for gasification in the demo CHP plant for co-generation: electricity and heat, chippers were analyzed due to: the type of mobility, running for chipping and the method of delivering chips to temporary yard. The plant was planned to generate electricity power up to 200kWelec. First, in consideration were taken the chippers with medium capacity, which mainly served for chipping brushwood and leaves that remain after harvest plantations on mostly flat terrain and parks. Later, the comparative characteristics of the world's three largest manufacturers of machinery for the production of wood chips significantly larger amounts (up to 30m3/h were given. These chippers were particularly suitable for the higher density of crops and stationed yard, in which brushwood would be brought and chip. At the end, the types of convective dryers were analyzed that could be successfully used for drying wood chips (drum and pneumatic dryer and based on the calculation proposed the types of dryers that were available in the local market.

  14. Liquefaction of torrefied wood using microwave irradiation

    Science.gov (United States)

    Mengchao Zhou; Thomas Eberhardt; Pingping Xin; Chung-Yun Hse; Hui Pan

    2016-01-01

    Torrefaction is an effective pretreatment method to improve the uniformity and quality of lignocellulosic biomass before further thermal processing (e.g., gasification, combustion). The objective of this study was to determine the impacts of torrefaction as a pretreatment before liquefaction. Wood chips were torrefied for 2 h at three different temperatures (230, 260,...

  15. A national optimisation model for energy wood streams; Energiapuuvirtojen valtakunnallinen optimointimalli

    Energy Technology Data Exchange (ETDEWEB)

    Iikkanen, P.; Keskinen, S.; Korpilahti, A.; Raesaenen, T.; Sirkiae, A.

    2011-07-01

    In 2010 a total of 12,5 terawatt hours of forest energy was used in Finland's heat and power plants. According to studies by Metsaeteho and Poeyry, use of energy wood will nearly double to 21.6 terawatt hours by 2020. There are also plans to use energy wood as a raw material for biofuel plants. The techno-ecological supply potential of energy wood in 2020 is estimated at 42.9 terawatt hours. Energy wood has been transported almost entirely by road. The situation is changing, however, because growing demand for energy wood will expand raw wood procurement areas and lengthen transport distances. A cost-effective transport system therefore also requires the use of rail and waterway transports. In Finland, however, there is almost a complete absence of the terminals required for the use of rail and waterway transports; where energy wood is chipped, temporarily stored and loaded onto railway wagons and vessels for further transport. A national optimisation model for energy wood has been developed to serve transport system planning in particular. The linear optimisation model optimises, on a national level, goods streams between supply points and usage points based on forest energy procurement costs. The model simultaneously covers deliveries of forest chips, stumps and small-sized thinning wood. The procurement costs used in the optimisation include the costs of the energy wood's roadside price, chipping, transport and terminal handling. The transport system described in the optimisation model consists of wood supply points (2007 municipality precision), wood usage points, railway terminals and the connections between them along the main road and rail network. Elements required for the examination of waterway transports can also be easily added to the model. The optimisation model can be used to examine, for example, the effects of changes of energy wood demand and supply as well as transport costs on energy wood goods streams, the relative use of different

  16. A local heating system using wood fuel from farms

    International Nuclear Information System (INIS)

    Kiukaanniemi, E.; Kurvinen, T.

    1998-01-01

    This report is a part of the a project on sustainable biomass utilization chains. The project belongs to a larger group of studies on northern biomass utilization by the Thule Institute and the University of Oulu. A cooperative energy society working in the municipality of Perho (3400 inhabitants) in Finland has been studied in this report. The cooperative energy society delivers energy which is generated from wood chips to the Perho municipality. Generated energy has a competitive price compared with fuel oils. In addition, harvesting, chipping and transporting give the members of the society an extra income. Members need not to make any investments in new equipment in order to work in the co-operative society because the machinery needed is the same as the one they use for other forestry activities. The price of the energy generated by wood chips is bound to the price of alternative fuels. There is a 5 MW district heating plant in Perho municipality containing a 1.4 MW solid fuel fired boiler with grate and 1.6 MW and 2.0 MW oil fired boilers. An investment in a heating plant containing a solid fuel fired boiler is often many times greater than that of one containing an oil fired boiler. There are many advantages which are hard to evaluate in generating energy from wood fuel. E.g. employment, increased income from taxes, an increase in the cash flow in the municipality and the advantages for forest growth. When undersized trees are removed from a forest stand, the remaining trees will grow better. The advantage of forestry is, however, hard to evaluate in cash terms. There has been an estimate that the advantage is 50-100 FIM/ha/a when compared to the yield of unthinned pine forest. Studies have shown that the money paid for energy in the area may be recycled several times in purchasing products and services in the area. In Perho municipality, it has been estimated that over half million FIM of extra cash has been generated and invested in the area by the

  17. Production of wood pellets. Influence of additives on production, quality, storage, combustion and life cycle analysis of wood pellets; Herstellung von Holzpellets. Einfluss von Presshilfsmitteln auf Produktion, Qualitaet, Lagerung, Verbrennung sowie Energie- und Oekobilanz von Holzpellets

    Energy Technology Data Exchange (ETDEWEB)

    Hasler, P.; Nussbaumer, T. [Verenum, Zuerich (Switzerland); Buerli, J. [Buerli Pellets, Willisau (Switzerland)

    2001-07-01

    This report for the Swiss Federal Office of Energy (SFOE) presents the results of a study concerning the influence of additives on the various factors related to the manufacture of wood pellets and their use. Results of tests concerning the production, storage and combustion of wood pellets with and without additives are presented. Process modifications are discussed. The report shows that for all investigated additives neither energy consumption nor pellet throughput was improved. The influence of additives on the mechanical strength of the pellets is discussed, as are the combustion characteristics of the pellets, which emit significantly lower levels of NO{sub x} and particulate matter than typical wood chips. The authors recommend the application of advanced control technology to ensure optimum combustion conditions. A life-cycle analysis is presented which shows that pellets are ecologically more favourable than wood chips. The ecological potential for improvement in the manufacturing process is discussed, including emission reductions and heat recovery.

  18. Comparative studies on storage and drying of chips and chunks in Norway

    Energy Technology Data Exchange (ETDEWEB)

    Gjoelsjoe, S. (Norwegian Forest Research Inst. (Norway))

    1988-11-01

    Knowledge of sporulation and alteration in moisture content and dry-matter content is essential when trying to determine optimal conditions for storage of wood fuel. The object of this experiment has been to study the progression of these variables in wood fuel of varying sizes. The material used was debranched stemwood of birch. The wood was comminuted up and stored in three different sizes. The sizes were chips (length approx. 3 cm), chunkwood (approx. 8 cm) and firewood (approx. 15 cm). The fuelwood was stored in bines of 10 m{sup 3} with netting floor and netting walls. Six of the bins were covered, the remaining six were without cover. The highest temperature increase was found in chips, particularly during the first stages of storage when temperature reached approximately 30 C. The other fuel sizes had temperature close to ambient temperature. At the start of the test, moisture content was approximately 40 %. By the end of the test the moisture content was below 20% for firewood and chunkwood under cover. The moisture was measured 50 cm from the top and 50 cm from the sidewall of the bin. Whilst chips without cover had a moisture content of more than 60%. Storage under cover resulted in a higher reduction of moisture content than storage without cover. The smaller sizes exhibited the greatest difference in moisture content. The highest dry-matter loss during the storage time was found in chips stored under cover, approximately 1.2% per month. Dry-matter loss was lowest in firewood stored under cover 0.07% per month. Dry-matter loss decreased with increasing size. Spores and dust particles had the highest concentrations in chips and lowest in firewood. (12 refs., 10 figs., 8 tabs.) (au).

  19. Development of new all-terrain chip harvester

    International Nuclear Information System (INIS)

    Helevirta, K.

    2001-01-01

    The objective of the project is to develop a new, efficient, reliable and profitable wood harvesting machine for serial production, which could be applied for chipping of logging residues and forest energy from thinnings at the lot, and which would fit into the harvesting chain. The project has been carried out by developing first a method prototype. Biowatti Oy, mastering the harvesting chains of forest energy, has tested the method and the concept, and approved it to be operable. The machine has been delivered to an experienced forest entrepreneur for testing in actual field conditions. Final productivity tests have not been finished yet, and the results have not been analyzed. Preliminary results show that when chipping the residues at the lot, using 300-m haulage distance and unloading into a chip lorry, the productivity to be about 60 bulk-m 3 /h, and the fuel consumption to be 1,1 liters/bulk m 3 . The machine can be fueled by tax-free fuel oil. The PIKA LOCH 2000 chipper, developed in the project, will first be marketed in Finland, Sweden and other parts of Europe. In Finland there is a need for lot- chippers and employment of them so they can get investment subsidies from the Finnish Ministry of Trade and Industry, which is expected to increase the share of lot-chippers in harvesting of wood energy. (orig.)

  20. Manufacture, delivery and marketing of wood pellets

    International Nuclear Information System (INIS)

    Huhtanen, T.

    2001-01-01

    Wood pellet is a cheap fuel, the use of which can easily bee automated. Pellet heating can be carried out with a stoker or a pellet burner, which can be mounted to oil and solid fuels boiler or to solid fuel boilers. Vapo Oy delivers wood pellet to farms and detached houses via Agrimarket stores. Vapo Oy delivers pellets to large real estates, municipalities, industry, greenhouses and power plants directly as bulk. The pellets are delivered either by trailers or lorries equipped with fan-operated unloaders. The use of wood pellets is a suitable fuel especially for real estates, the boiler output of which is 20 - 1000 kW. Vapo Oy manufactures wood pellets of cutter chips, grinding dust and sawdust. The raw material for Ilomantsi pellet plant is purchased from the province of North Karelia. The capacity of pelletizing plant is 45 000 t of pellets per year, half of which is exported mainly to Sweden and Denmark

  1. In situ high-temperature gas sensors: continuous monitoring of the combustion quality of different wood combustion systems and optimization of combustion process

    Directory of Open Access Journals (Sweden)

    H. Kohler

    2018-03-01

    Full Text Available The sensing characteristics and long-term stability of different kinds of CO ∕ HC gas sensors (non-Nernstian mixed potential type during in situ operation in flue gas from different types of low-power combustion systems (wood-log- and wood-chip-fuelled were investigated. The sensors showed representative but individual sensing behaviour with respect to characteristically varying flue gas composition over the combustion process. The long-term sensor signal stability evaluated by repeated exposure to CO ∕ H2 ∕ N2 ∕ synthetic air mixtures showed no sensitivity loss after operation in the flue gas. Particularly for one of the sensors (Heraeus GmbH, this high signal stability was observed in a field test experiment even during continuous operation in the flue gas of the wood-chip firing system over 4 months. Furthermore, it was experimentally shown that the signals of these CO ∕ HC sensing elements yield important additional information about the wood combustion process. This was demonstrated by the adaptation of an advanced combustion airstream control algorithm on a wood-log-fed fireplace and by the development of a combustion quality monitoring system for wood-chip-fed central heaters.

  2. Loading and Unloading Weaned Pigs: Effects of Bedding Types, Ramp Angle, and Bedding Moisture

    Directory of Open Access Journals (Sweden)

    Arlene Garcia

    2014-12-01

    Full Text Available The use of non-slip surfaces during loading and unloading of weaned pigs plays an important role in animal welfare and economics of the pork industry. Currently, the guidelines available only suggest the use of ramps below 20° to load and unload pigs. Three ramp angles (0°, 10° or 20°, five bedding materials (nothing, sand, feed, wood shavings or wheat straw hay, two moistures (dry or wet bedding; >50% moisture over two seasons (>23.9 °C summer, <23.9 °C winter were assessed for slips/falls/vocalizations (n = 6,000 pig observations. “Score” was calculated by the sum of slips, falls, and vocalizations. With the exception of using feed as a bedding, all beddings provided some protection against elevated slips, falls, and vocalizations (P < 0.01. Providing bedding reduced (P < 0.05 scores regardless of whether the bedding was dry or wet. Scores increased as the slope increased (P < 0.01. Provision of bedding, other than feed, at slopes greater than zero, decreased slips, falls and vocalizations. The total time it took to load and unload pigs was

  3. Development of a trickle bed reactor of electro-Fenton process for wastewater treatment

    International Nuclear Information System (INIS)

    Lei, Yangming; Liu, Hong; Shen, Zhemin; Wang, Wenhua

    2013-01-01

    Highlights: • An electrochemical trickle bed reactor was composed of C-PTFE-coated graphite chips. • The trickle bed reactor had a high H 2 O 2 production rate in a dilute electrolyte. • An azo dye was effectively decomposed by the electro-Fenton process in the reactor. -- Abstract: To avoid electrolyte leakage and gas bubbles in the electro-Fenton (E-Fenton) reactors using a gas diffusion cathode, we developed a trickle bed cathode by coating a layer composed of carbon black and polytetrafluoroethylene (C-PTFE) onto graphite chips instead of carbon cloth. The trickle bed cathode was optimized by single-factor and orthogonal experiments, in which carbon black, PTFE, and a surfactant were considered as the determinant of the performance of graphite chips. In the reactor assembled by the trickle bed cathode, H 2 O 2 was generated with a current of 0.3 A and a current efficiency of 60%. This performance was attributed to the fine distribution of electrolyte and air, as well as the effective oxygen transfer from the gas phase to the electrolyte–cathode interface. In terms of H 2 O 2 generation and current efficiency, the developed trickle bed reactor had a performance comparable to that of the conventional E-Fenton reactor using a gas diffusion cathode. Further, 123 mg L −1 of reactive brilliant red X-3B in aqueous solution was decomposed in the optimized trickle bed reactor as E-Fenton reactor. The decolorization ratio reached 97% within 20 min, and the mineralization reached 87% within 3 h

  4. Co-combustion of anthracite coal and wood pellets: Thermodynamic analysis, combustion efficiency, pollutant emissions and ash slagging.

    Science.gov (United States)

    Guo, Feihong; Zhong, Zhaoping

    2018-08-01

    This work presents studies on the co-combustion of anthracite coal and wood pellets in fluidized bed. Prior to the fluidized bed combustion, thermogravimetric analysis are performed to investigate the thermodynamic behavior of coal and wood pellets. The results show that the thermal decomposition of blends is divided into four stages. The co-firing of coal and wood pellets can promote the combustion reaction and reduce the emission of gaseous pollutants, such as SO 2 and NO. It is important to choose the proportion of wood pellets during co-combustion due to the low combustion efficiency caused by large pellets with poor fluidization. Wood pellets can inhibit the volatilization of trace elements, especially for Cr, Ni and V. In addition, the slagging ratio of wood pellets ash is reduced by co-firing with coal. The research on combustion of coal and wood pellets is of great significance in engineering. Copyright © 2018 Elsevier Ltd. All rights reserved.

  5. Evaluation of free-stall mattress bedding treatments to reduce mastitis bacterial growth

    Energy Technology Data Exchange (ETDEWEB)

    Kristula, M A; Dou, Z; Toth, J D; Smith, B I; Harvey, N; Sabo, M [University of Penn, Kennett Square, PA (United States)

    2008-05-15

    Bacterial counts were compared in free-stall mattresses and teat ends exposed to 5 treatments in a factorial study design on 1 dairy farm. Mattresses in five 30-cow groups were subjected to 1 of 5 bedding treatments every other day: 0.5 kg of hydrated limestone, 120 mL of commercial acidic conditioner, 1 kg of coal fly ash, 1 kg of kiln-dried wood shavings, and control (no bedding). Counts of coliforms, Klebsiella spp., Escherichia coli, and Streptococcus spp. were lowest on mattresses bedded with lime. Mattresses bedded with the commercial acidic conditioner had the next lowest counts for coliforms, Klebsiella spp., and Streptococcus spp. Wood shavings and the no-bedding control had the highest counts for coliform and Klebsiella spp. Compared with wood shavings or control, fly ash reduced the counts of coliforms, whereas for the other 3 bacterial groups, the reduction was not always significant. Streptococcus spp. counts were greatest in the control group and did not differ among the shavings and fly ash groups. Teat swab results indicated that hydrated lime was the only bedding treatment that significantly decreased the counts of both coliforms and Klebsiella spp. There were no differences in Streptococcus spp. numbers on the teats between any of the bedding treatments. Bacterial populations grew steadily on mattresses and were generally higher at 36 to 48 h than at 12 to 24 h, whereas bacterial populations on teats grew rapidly by 12 h and then remained constant. Hydrated lime was the only treatment that significantly reduced bacterial counts on both mattresses and teat ends, but it caused some skin irritation.

  6. Production of bio-oil with low contents of copper and chlorine by fast pyrolysis of alkaline copper quaternary-treated wood in a fluidized bed reactor

    International Nuclear Information System (INIS)

    Koo, Won-Mo; Jung, Su-Hwa; Kim, Joo-Sik

    2014-01-01

    Fast pyrolysis of ACQ (alkaline copper quaternary)-treated wood was carried out in a bench-scale pyrolysis plant equipped with a fluidized bed reactor and char separation system. This study focused on the production of a bio-oil with low copper and chlorine contents, especially by adopting the fractional condensation of bio-oil using water condensers, an impact separator and an electrostatic precipitator. In addition, various analytical tools were applied to investigate the physicochemical properties of the pyrolysis products and the behavior of the preservative during pyrolysis. The bio-oil yield was maximized at 63.7 wt% at a pyrolysis temperature of 411 °C. Highly water-soluble holocellulose-derived components such as acetic acid and hydroxyacetone were mainly collected by the condensers, while lignin-derived components and levoglucosan were mainly observed in the oils collected by the impact separator and electrostatic precipitator. All the bio-oils produced in the experiments were almost free of copper and chlorine. Most copper in ACQ was transferred into the char. - Highlights: • ACQ(alkaline copper quaternary)-treated wood was successfully pyrolyzed in a bench-scale fluidized bed. • Bio-oils separately collected were different in their characteristics. • Bio-oils were free of didecyldimethylammonium chloride. • Bio oils were almost free of copper and chlorine. • The concentration of levoglucosan in a bio-oil was 24–31 wt%

  7. Solutions for wood-based bio-energy price discovery

    Energy Technology Data Exchange (ETDEWEB)

    Teraes, Timo [FOEX Indexes Ltd., Helsinki (Finland)], e-mail: timo@foex.fi

    2012-11-01

    Energy prices are highly volatile. This volatility can have serious ill-effects on the profitability of companies engaged in the energy business. There are, however, a number of price risk management tools which can be used to reduce the problems caused by price volatility. International trade of wood pellets and wood chips is rapidly growing. A good price transparency helps in developing the trade further. In order to meet the renewable energy targets within the EU, further growth of volumes is needed, at least within Europe and from overseas supply sources to the European markets. Reliable price indices are a central element in price risk management and in general price discovery. Exchanges have provided, in the past, the most widely known price discovery systems. Since 1990's, an increasing number of price risk management tools has been based on cash settlement concept. Cash settlement requires high quality benchmark price indices. These have been developed by the exchanges themselves, by trade press and by independent price benchmark provider companies. The best known of these benchmarks in forest industry and now also in wood-based bioenergy products are the PIX indices, provided by FOEX Indexes Ltd. This presentation discusses the key requirements for a good price index and the different ways of using the indices. Price relationships between wood chip prices and pellet prices are also discussed as will be the outlook for the future volume growth and trade flows in woodchips and pellets mainly from the European perspective.

  8. Performance of novel sludge-bed anaerobic membrane bioreactor (SB-AnMBR) treating prehydrolysis liquor.

    Science.gov (United States)

    Kale, Mayur M; Singh, Kripa S

    2014-01-01

    The feasibility of a novel sludge-bed anaerobic membrane bioreactor (SB-AnMBR) configuration for treating a waste stream from a dissolving pulp production industry was evaluated. The waste stream, called prehydrolysis liquor (PHL), is generated after the wood chips are subjected to high temperature steam to remove unwanted hemicelluloses. The PHL with total chemical oxygen demand (COD) of approximately 100 g/L contained mainly sugars, furfural, lignin, and acetic acid. The SB-AnMBR was fed with the PHL at organic loading rates in a range of 0.8 to10 kg-COD/(m(3)·d). The COD removal efficiency of more than 85% and an average rate of methane production of 0.35 m(3)/(kg-COD·d) were observed at each loading rate. No detectable sugars or furfural were present in the treated effluent from SB-AnMBR. Lignin removal varied from 60 to 90%. Flat-sheet membranes performed well with one fouling event during first 400 days of operation.

  9. Utilisation of Estonian energy wood resources

    Energy Technology Data Exchange (ETDEWEB)

    Muiste, P.; Tullus, H.; Uri, V. [Estonian Agricultural University, Tartu (Estonia)

    1996-12-31

    In the end of the Soviet period in the 1980s, a long-term energy programme for Estonia was worked out. The energy system was planned to be based on nuclear power and the share of domestic alternative sources of energy was low. The situation has greatly changed after the re-establishment of the Estonian independence, and now wood and peat fuels play an important role in the energy system. Energy consumption in Estonia decreased during the period 1970-1993, but this process has less influenced the consumption of domestic renewable fuels - peat and wood. It means that the share of these fuels has grown. The investment on substitution of imported fossil fuels and on conversion of boiler plants from fossil fuels to domestic fuels has reached the level of USD 100 million. The perspectives of the wood energy depend mainly on two factors; the resources and the price of wood energy compared with other fuels. The situation in wood market influences both the possible quantities and the price. It is typical that the quickly growing cost of labour power in Estonia is greatly affecting the price of energy wood. Though the price level of fuel peat and wood chips is lower than the world market price today, the conditions for using biofuels could be more favourable, if higher environmental fees were introduced. In conjunction with increasing utilisation of biofuels it is important to evaluate possible emissions or removal of greenhouse gases from Estonian forests 3 refs.

  10. Utilisation of Estonian energy wood resources

    Energy Technology Data Exchange (ETDEWEB)

    Muiste, P; Tullus, H; Uri, V [Estonian Agricultural University, Tartu (Estonia)

    1997-12-31

    In the end of the Soviet period in the 1980s, a long-term energy programme for Estonia was worked out. The energy system was planned to be based on nuclear power and the share of domestic alternative sources of energy was low. The situation has greatly changed after the re-establishment of the Estonian independence, and now wood and peat fuels play an important role in the energy system. Energy consumption in Estonia decreased during the period 1970-1993, but this process has less influenced the consumption of domestic renewable fuels - peat and wood. It means that the share of these fuels has grown. The investment on substitution of imported fossil fuels and on conversion of boiler plants from fossil fuels to domestic fuels has reached the level of USD 100 million. The perspectives of the wood energy depend mainly on two factors; the resources and the price of wood energy compared with other fuels. The situation in wood market influences both the possible quantities and the price. It is typical that the quickly growing cost of labour power in Estonia is greatly affecting the price of energy wood. Though the price level of fuel peat and wood chips is lower than the world market price today, the conditions for using biofuels could be more favourable, if higher environmental fees were introduced. In conjunction with increasing utilisation of biofuels it is important to evaluate possible emissions or removal of greenhouse gases from Estonian forests 3 refs.

  11. Chipping operations and efficiency in different operational environments

    Energy Technology Data Exchange (ETDEWEB)

    Roeser, D.; Mola-Yudego, B.; Prinz, R.; Emer, B.; Sikanen, L., e-mail: dominik.roser@metla.fi

    2012-11-01

    This research analyses the productivity of energy wood chipping operations at several sites in Austria and Finland. The aim of the work is to examine the differences in productivity and the effects of the operational environment for the chipping of bioenergy at the roadside. Furthermore, the study quantifies the effects of different variables such as forest energy assortments, tree species, sieve size and machines on the overall productivity of chipping. The results revealed that there are significant differences in the chipping productivity in Austria and Finland which are largely based on the use of different sieve sizes. Furthermore, the different operational environments in both countries, as well as the characteristics of the raw material also seem to have an effect on productivity. In order to improve the chipping productivity, particularly in Central European conditions, all relevant stakeholders need to work jointly to find solutions that will allow a greater variation of chip size. Furthermore, in the future more consideration has to be given to the close interlinkage between the chipper, crane and grapple. As a result, investments costs can be optimized and operational costs and stress on the machines reduced. (orig.)

  12. Spectroscopic analysis of hot-water- and dilute-acid-extracted hardwood and softwood chips

    Science.gov (United States)

    Lehto, Joni; Louhelainen, Jarmo; Huttunen, Marko; Alén, Raimo

    2017-09-01

    Hot-water and dilute sulfuric acid pretreatments were performed prior to chemical pulping for silver/white birch (Betula pendula/B. pubescens) and Scots pine (Pinus sylvestris) chips to determine if varying pretreatment conditions on the original wood material were detectable via attenuated total reflectance (ATR) infrared spectroscopy. Pretreatment conditions varied with respect to temperature (130 °C and 150 °C) and treatment time (from 30 min to 120 min). The effects of the pretreatments on the composition of wood chips were determined by ATR infrared spectroscopy. The spectral data were compared to those determined by common wood chemistry analyses to evaluate the suitability of ATR spectroscopy method for rapid detection of changes in the wood chemical composition caused by different pretreatment conditions. In addition to determining wood species-dependent differences in the wood chemical composition, analytical results indicated that most essential lignin- and carbohydrates-related phenomena taking place during hot-water and acidic pretreatments could be described by applying this simple spectral method requiring only a small sample amount and sample preparation. Such information included, for example, the cleavage of essential lignin bonds (i.e., mainly β-O-4 linkages in guaiacyl and syringyl lignin) and formation of newly condensed lignin structures under different pretreatment conditions. Carbohydrate analyses indicated significant removal of hemicelluloses (especially hardwood xylan) and hemicelluloses-derived acetyl groups during the pretreatments, but they also confirmed the highly resistant nature of cellulose towards mild pretreatments.

  13. Development of a trickle bed reactor of electro-Fenton process for wastewater treatment

    Energy Technology Data Exchange (ETDEWEB)

    Lei, Yangming [Key Laboratory of Reservoir Aquatic Environment, Chongqing Institute of Green and Intelligent Technology, Chinese Academy of Sciences, Chongqing 401122 (China); School of Environmental Science and Engineering, Shanghai Jiao Tong University, Shanghai 200240 (China); Liu, Hong, E-mail: liuhong@cigit.ac.cn [Key Laboratory of Reservoir Aquatic Environment, Chongqing Institute of Green and Intelligent Technology, Chinese Academy of Sciences, Chongqing 401122 (China); Shen, Zhemin, E-mail: zmshen@sjtu.edu.cn [School of Environmental Science and Engineering, Shanghai Jiao Tong University, Shanghai 200240 (China); Wang, Wenhua [School of Environmental Science and Engineering, Shanghai Jiao Tong University, Shanghai 200240 (China)

    2013-10-15

    Highlights: • An electrochemical trickle bed reactor was composed of C-PTFE-coated graphite chips. • The trickle bed reactor had a high H{sub 2}O{sub 2} production rate in a dilute electrolyte. • An azo dye was effectively decomposed by the electro-Fenton process in the reactor. -- Abstract: To avoid electrolyte leakage and gas bubbles in the electro-Fenton (E-Fenton) reactors using a gas diffusion cathode, we developed a trickle bed cathode by coating a layer composed of carbon black and polytetrafluoroethylene (C-PTFE) onto graphite chips instead of carbon cloth. The trickle bed cathode was optimized by single-factor and orthogonal experiments, in which carbon black, PTFE, and a surfactant were considered as the determinant of the performance of graphite chips. In the reactor assembled by the trickle bed cathode, H{sub 2}O{sub 2} was generated with a current of 0.3 A and a current efficiency of 60%. This performance was attributed to the fine distribution of electrolyte and air, as well as the effective oxygen transfer from the gas phase to the electrolyte–cathode interface. In terms of H{sub 2}O{sub 2} generation and current efficiency, the developed trickle bed reactor had a performance comparable to that of the conventional E-Fenton reactor using a gas diffusion cathode. Further, 123 mg L{sup −1} of reactive brilliant red X-3B in aqueous solution was decomposed in the optimized trickle bed reactor as E-Fenton reactor. The decolorization ratio reached 97% within 20 min, and the mineralization reached 87% within 3 h.

  14. Energy requirement for fine grinding of torrefied wood

    Energy Technology Data Exchange (ETDEWEB)

    Repellin, Vincent; Govin, Alexandre; Guyonnet, Rene [Department of Powder and Multi-Components Materials (PMMC), SPIN Research Center, Ecole des Mines de Saint Etienne (EMSE), 158 Cours Fauriel, F-42023 Saint-Etienne (France); Rolland, Matthieu [Process Developments and Engineering Division, Chemical Engineering Department, Institut Francais du Petrole (IFP-Lyon), F-69390 Vernaison (France)

    2010-07-15

    The purpose of this study is to investigate the influence of torrefaction on wood grinding energy. Wood chips were torrefied at different temperatures and durations. The energy required to obtain fine powder was measured. Particle size analyses were carried out on each powder sample. It is showed that torrefaction decreases both grinding energy and particle size distribution. A criterion to compare grindability of natural and torrefied wood is proposed. It takes into account both grinding energy and particle size distribution. It accounts the energy required for grinding particles to sizes inferior to 200 {mu}m, for given grinding conditions. Torrefaction is characterised by the anhydrous weight loss (AWL) of wood. For AWL inferior to around 8%, grinding energy decreases fast. Over 8%, grinding energy decreases at a slow rate. Particle size distribution decreases linearly as the AWL increases. Both for spruce and beech, the grinding criterion is decreased of 93% when the AWL is around 28%. (author)

  15. Modeling of reaction kinetics in bubbling fluidized bed biomass gasification reactor

    Energy Technology Data Exchange (ETDEWEB)

    Thapa, R.K.; Halvorsen, B.M. [Telemark University College, Kjolnes ring 56, P.O. Box 203, 3901 Porsgrunn (Norway); Pfeifer, C. [University of Natural Resources and Life Sciences, Vienna (Austria)

    2013-07-01

    Bubbling fluidized beds are widely used as biomass gasification reactors as at the biomass gasification plant in Gussing, Austria. The reactor in the plant is a dual circulating bubbling fluidized bed gasification reactor. The plant produces 2MW electricity and 4.5MW heat from the gasification of biomass. Wood chips as biomass and olivine particles as hot bed materials are fluidized with high temperature steam in the reactor. As a result, biomass undergoes endothermic chemical reaction to produce a mixture of combustible gases in addition to some carbon-dioxide (CO2). The combustible gases are mainly hydrogen (H2), carbon monoxide (CO) and methane (CH4). The gas is used to produce electricity and heat via utilization in a gas engine. Alternatively, the gas is further processed for gaseous or liquid fuels, but still on the process of development level. Composition and quality of the gas determine the efficiency of the reactor. A computational model has been developed for the study of reaction kinetics in the gasification rector. The simulation is performed using commercial software Barracuda virtual reactor, VR15. Eulerian-Lagrangian approach in coupling of gas-solid flow has been implemented. Fluid phase is treated with an Eulerian formulation. Discrete phase is treated with a Lagrangian formulation. Particle-particle and particle-wall interactions and inter-phase heat and mass transfer have been taken into account. Series of simulations have been performed to study model prediction of the gas composition. The composition is compared with data from the gasifier at the CHP plant in Güssing, Austria. The model prediction of the composition of gases has good agreements with the result of the operating plant.

  16. MINERGIE modules: heat pump - heat pump/solar - wood - wood/solar; Minergie-Module Waermepumpe - Waermepumpe/Solar - Holz - Holz/Solar

    Energy Technology Data Exchange (ETDEWEB)

    Gallati, J. [Seecon GmbH, Lucerne (Switzerland); Portmann, M. [Buero Markus Portmann, Kriens (Switzerland); Zurfluh, B. [Zurfluh Lottenbach, Lucerne (Switzerland)

    2005-07-01

    This research report for the Swiss Federal Office of Energy (SFOE) presents the results of a project that examined the feasibility of setting up 'MINERGIE' low-energy-consumption module standards for the production of heat in small residential buildings. The aims of the standards and the basic idea behind the MINERGIE-modules are discussed. The concepts of the modules for heat pumps and wood-fired heating systems and their combination with solar installations are examined, as are their areas of application. The requirements placed on the modules are listed. System concepts, including simple schematics for typical installations, are presented for wood-log, wood-chippings and pellets-fired systems as well as for ground-loop and air-water heat pump systems as well as their solar-aided counterparts. The results of cost-benefit analyses are presented and questions regarding system guarantee and liability are examined.

  17. Wood-energy - The sector get worried

    International Nuclear Information System (INIS)

    Mary, Olivier; Signoret, Stephane; Bohlinger, Philippe; Guilhem, Jean; De Santis, Audrey; Sredojevic, Alexandre; Defaye, Serge; Maindrault, Marc

    2017-01-01

    Wood energy is, today and certainly also tomorrow, one of the most important renewable energies in France. However, the wood-energy sector seems to slow down as hydrocarbon prices stay extremely low. This document presents 8 articles, describing the context and the characteristics of this evolution, plus some examples of developments in France. The themes of the articles are: the activity of the wood-energy sector should be reinforced to meet the objectives of the French energy multi-year plan; The 2035 prospective of the wood yield in the French forest will meet the future demand, however this evaluation does not take into consideration the effects of the climatic change; the conversion to biomass of the 'Fort de l'Est' (near Paris) heating system (equipped with a boiling fluidized bed boiler) has enabled the heat network to beat the 50 pc share of renewable energy; wood-energy professionals use the 'quality' lever to challenge their fossil fuel competitors; the city of Orleans is now equipped with an innovative biomass cogeneration plant; the example of wood waste valorization in a French sawmill; the French ONF (Forest Administration) Wood-Energy actor has just inaugurated its largest biomass dryer, in order to develop the domestic market for wood as a fuel; analysis of the technical and economical feasibility of using wood to generate electric power or replacing electric space heating by heat network

  18. Caracterização da estrutura anatômica, densidade básica e morfologia de cavacos da madeira de Eucalyptus grandis para a produção de painéis MDF Characterization of wood anatomy, basic density, and morphology of Eucalyptus grandis chips for MDF production

    Directory of Open Access Journals (Sweden)

    Ugo Leandro Belini

    2008-08-01

    Full Text Available O aumento na produção dos painéis "Medium Density Fiberboard" (MDF confeccionados com madeira de espécies de Eucalyptus spp de rápido crescimento evidencia a necessidade da caracterização dos seus componentes celulares, da densidade básica e da morfologia de cavacos. Com esse objetivo, foram coletadas três amostras de cavacos de madeira de árvores de Eucalyptus grandis, na linha de produção de indústria de painel. Em laboratório, os cavacos foram dissociados por maceração, para a avaliação das dimensões das fibras e dos vasos; determinou-se a densidade básica dos cavacos, bem como se caracterizaram a sua espessura e morfologia. Os resultados indicaram valores médios de 1005-19,7-11,8-3,9 µm para o comprimento, largura, diâmetro do lume e espessura média da parede das fibras, respectivamente. A densidade básica da madeira foi de 0,432 g/cm³ e a espessura dos cavacos, de 4,36 mm. Os valores médios de retenção dos cavacos foram de 0,9-16,9-44,5-30,7-6,1-0,9% nas peneiras 40, 25, 16, 8, 3,35 mm e fundo, respectivamente, sendo 75,2% retidos nas peneiras de 16-8 mm de abertura. Os resultados das análises anatômicas e morfológicas dos cavacos de madeira foram discutidos e comparados com informações da literatura especializada e correlacionados com o processo produtivo de chapas MDF.The increase of the MDF panels (Medium Density Fiberboard production by the use of the fast growing eucalypt wood species it evidences the need of the characterization of the cellular components, basic density and the chips morphology. With this aim 3 samples of wood chips of Eucalyptus grandis trees were collected, in the production line of panel industry. In laboratory, the wood chips were dissociated by maceration for the evaluation of the fiber and vessels dimensions; the wood basic density was determined and the thickness and morphology were characterized. The results indicated mean values of 1005-19,7-11,8-3,9 µm for the fiber length

  19. Fly ash classification efficiency of electrostatic precipitators in fluidized bed combustion of peat, wood, and forest residues.

    Science.gov (United States)

    Ohenoja, Katja; Körkkö, Mika; Wigren, Valter; Österbacka, Jan; Illikainen, Mirja

    2018-01-15

    The increasing use of biomasses in the production of electricity and heat results in an increased amount of burning residue, fly ash which disposal is becoming more and more restricted and expensive. Therefore, there is a great interest in utilizing fly ashes instead of just disposing of it. This study aimed to establish whether the utilization of fly ash from the fluidized bed combustion of peat, wood, and forest residues can be improved by electrostatic precipitator separation of sulfate, chloride, and some detrimental metals. Classification selectivity calculations of electrostatic precipitators for three different fuel mixtures from two different power plants were performed by using Nelson's and Karnis's selectivity indices. Results showed that all fly ashes behaved similarly in the electrostatic separation process SiO 2 resulted in coarse fractions with Nelson's selectivity of 0.2 or more, while sulfate, chloride, and the studied detrimental metals (arsenic, cadmium, and lead) enriched into fine fractions with varying selectivity from 0.2 to 0.65. Overall, the results of this study suggest that it is possible to improve the utilization potential of fly ashes from fluidized bed combustion in concrete, fertilizer, and earth construction applications by using electrostatic precipitators for the fractionating of fly ashes in addition to their initial function of collecting fly ash particles from flue gases. The separation of the finer fractions (ESP 2 and 3) from ESP 1 field fly ash is recommended. Copyright © 2017 Elsevier Ltd. All rights reserved.

  20. Bioenergy Research Programme, Yearbook 1995. Production of wood fuels; Bioenergian tutkimusohjelma, vuosikirja 1995. Puupolttoaineen tuotantotekniikka

    Energy Technology Data Exchange (ETDEWEB)

    Alakangas, E [ed.

    1997-12-31

    Bioenergy Research Programme is one of the energy technology research programmes of the Technology Development Center TEKES. The aim of the Bioenergy Research Programme is to increase, by using technical research and development, the economically profitable and environmentally sound utilisation of bioenergy, to improve the competitiveness of present peat and wood fuels, and to develop new competitive fuels and equipment related to bioenergy. The funding for 1995 was nearly 52 million FIM and the number of projects 66. The main goal of the wood fuels research area is to develop new production methods in order to decrease the production costs to the level of imported fuels. The total potential of the wood fuel use should be at least 1.0 million toe/a (5.5 million m{sup 3}). During the year 1995 There were over 30 projects concerning the production of wood derived fuels going on. Nearly half of them focused on integrated production of pulp wood and wood fuel. About ten projects was carried out to promote the wood fuel production from logging residues. Other topics were firewood production, production logistics and wood fuel resources. For production of fuel chips from logging residues, a new chipper truck, MOHA-SISU, was introduced. The new machine gives a new logistic solution resulting in high productivity and reasonable operating costs. In Mikkeli region three years of active work promoted the usage of wood fuel in a district power plant to the level of over 110 000 m{sup 3} of fuel chips. The production costs tend to be a little high in average, and the production chain still needs to be improved

  1. Bioenergy Research Programme, Yearbook 1995. Production of wood fuels; Bioenergian tutkimusohjelma, vuosikirja 1995. Puupolttoaineen tuotantotekniikka

    Energy Technology Data Exchange (ETDEWEB)

    Alakangas, E. [ed.

    1996-12-31

    Bioenergy Research Programme is one of the energy technology research programmes of the Technology Development Center TEKES. The aim of the Bioenergy Research Programme is to increase, by using technical research and development, the economically profitable and environmentally sound utilisation of bioenergy, to improve the competitiveness of present peat and wood fuels, and to develop new competitive fuels and equipment related to bioenergy. The funding for 1995 was nearly 52 million FIM and the number of projects 66. The main goal of the wood fuels research area is to develop new production methods in order to decrease the production costs to the level of imported fuels. The total potential of the wood fuel use should be at least 1.0 million toe/a (5.5 million m{sup 3}). During the year 1995 There were over 30 projects concerning the production of wood derived fuels going on. Nearly half of them focused on integrated production of pulp wood and wood fuel. About ten projects was carried out to promote the wood fuel production from logging residues. Other topics were firewood production, production logistics and wood fuel resources. For production of fuel chips from logging residues, a new chipper truck, MOHA-SISU, was introduced. The new machine gives a new logistic solution resulting in high productivity and reasonable operating costs. In Mikkeli region three years of active work promoted the usage of wood fuel in a district power plant to the level of over 110 000 m{sup 3} of fuel chips. The production costs tend to be a little high in average, and the production chain still needs to be improved

  2. Energy from wood - part 3: automatic wood furnaces; Holzenergie, Teil 3: automatische Holzfeuerungen - Energie du bois, Partie 3: installations automatiques de chauffage au bois

    Energy Technology Data Exchange (ETDEWEB)

    Nussbaumer, T. [Verenum, Zuerich (Switzerland)

    2001-07-01

    The paper gives an overview on the technologies and applications of automatic wood furnaces. The combustion systems are defined by the flow condition: With increasing gas velocity, fixed bed, stationary fluidized bed (SFB), circulating fluidized bed (CFB), and entrained flow reactors are distinguished. The furnace design and typical applications are described. Further, a comparison is presented which gives data of the typical size range and fuel types for the different combustion systems. The most common fixed bed reactors are under-stoker and grate furnaces. While under-stoker furnaces are applied in the size range from 20 kW to 2.5 MW, grate furnaces cover the size range from a few 100 kW up to more than 50 MW. Under-stoker furnaces are well suited for wood fuel with low ash content, moderate water content and limited fuel size. Grate furnaces are also suited for fuel with high ash and water content and large fuel sizes. Hence grate furnaces are nowadays most common. Due to the higher technical needs, fluidized bed reactors are dedicated to large-scale applications, typically > 5 MW for SFB and > 15 MW for CFB. Furthermore, fluidized bed combustion needs more intensive fuel pre-treatment, since the fuel size is smaller than < 10 mm. On the other hand, it enables very high combustion efficiency, the utilization of difficult fuels and fuel mixtures. Dust burners using forced-flow conditions are limited to the application of fine fuel particles such as saw dust and often applied in combination with a grate furnaces > 5 MW. Beside the combustion technology, the most relevant measures for process control and pollutant emission abatement are described. Automatic wood furnaces are relevant sources of nitric oxide emissions and of particulates smaller than 10 micron (PM 10). Hence electrostatic precipitators and fabric filters are applied for efficient particle removal in large plants, while only cyclones with limited efficiency are used in applications up to 2 to 5 MW

  3. Dry matter losses and quality changes during short rotation coppice willow storage in chip or rod form.

    Science.gov (United States)

    Whittaker, Carly; Yates, Nicola E; Powers, Stephen J; Misselbrook, Tom; Shield, Ian

    2018-05-01

    This study compares dry matter losses and quality changes during the storage of SRC willow as chips and as rods. A wood chip stack consisting of approximately 74 tonnes of fresh biomass, or 31 tonnes dry matter (DM) was built after harvesting in the spring. Three weeks later, four smaller stacks of rods with an average weight of 0.8 tonnes, or 0.4 tonnes DM were built. During the course of the experiment temperature recorders placed in the stacks found that the wood chip pile reached 60 °C within 10 days of construction, but the piles of rods remained mostly at ambient temperatures. Dry matter losses were calculated by using pre-weighed independent samples within the stacks and by weighing the whole stack before and after storage. After 6 months the wood chip stack showed a DM loss of between 19.8 and 22.6%, and mean losses of 23.1% were measured from the 17 independent samples. In comparison, the rod stacks showed an average stack DM loss of between 0 and 9%, and between 1.4% and 10.6% loss from the independent samples. Analysis of the stored material suggests that storing willow in small piles of rods produces a higher quality fuel in terms of lower moisture and ash content; however, it has a higher fine content compared to storage in chip form. Therefore, according to the two storage methods tested here, there may be a compromise between maximising the net dry matter yield from SRC willow and the final fine content of the fuel.

  4. Production, Cost and Chip Characteristics of In-Woods Microchipping

    Science.gov (United States)

    J. Thompson; W. Sprinkle

    2013-01-01

    Emerging markets for biomass have increased the interest in producing microchips in the field. As a component of a large United States Department of Energy (DOE) funded project, microchipping has been trialed on a limited scale. The goal of the research was to evaluate the production, cost and chip characteristics of a mobile disc chipper configured to produce...

  5. Wood pyrolysis oil for diesel engines

    Energy Technology Data Exchange (ETDEWEB)

    Paro, D.; Gros, S.; Hellen, G.; Jay, D.; Maekelae, T.; Rantanen, O.; Tanska, T. [Wartsila Diesel International Ltd Oy, Vaasa (Finland)

    1996-12-01

    Wood Pyrolysis oil (WPO) has been identified by the Technical Research Centre of Finland (VTT) as the most competitive biofuel product which can be produced from biomass. The fuel is produced by a fast pyrolysis technique, using wood chipping`s or sawdust. The process can be applied to other recycling products such as straw etc. The use of WPO as a Diesel power plant fuel has been studied, and a fuel specification has been developed. The fuel characteristics have been analysed. There are several fuel properties addressed in the paper which have had to be overcome. New materials have been used in the fuel injection system. The fuel injection system development has progressed from a pump-line-pipe system to a common rail system. The fuel requires a pilot fuel oil injection to initiate combustion. The targets for the fuel injection system have been 1500 bar and 30 deg C injection period with a fuel of 15 MJ/kg lower heating value and 1220 Kg/m{sup 3} density. The combustion characteristics from both a small 80 mm bore engine initially, and then later with a single cylinder test of a 320 mm bore Waertsilae engine, have been evaluated. (author)

  6. Results of the production of wood derived fuels; Puupolttoaineiden tuotantotekniikka - tutkimusalueen katsaus

    Energy Technology Data Exchange (ETDEWEB)

    Korpilahti, A [Metsaeteho, Helsinki (Finland)

    1997-12-31

    During the year 1995 there were over 30 projects concerning the production of wood derived fuels going on. Nearly half of them focused on integrated production of pulp wood and wood fuel. About in ten projects work was carried out to promote wood fuel production from logging residues. Other topics were fire wood production, production logistics and wood fuel resources. For production of fuel chips from logging residues, a new chipper truck, MOHA-SISU, was introduced. Having ability to move on terrain, and equipped with drum chipper, hook technic for interchangeable containers and a trailer, the whole production chain can be carried out by the same machine. In Mikkeli region three years of active work promoted the usage of wood fuel in a district power plant to the level of over 110 000 cubic metres of fuel chips. The production costs tend to be a little high in average, and the production chain still needs to be improved. In the field of integrated production a great stride was taken when the first pilot plant using the MASSAHAKE-method started up. Components of the production line and knowledge to operate the process have increased resulting in good performance of the plant. And even another concept for integrated production was introduced. In order to fully control the debarking of small sized trees, a production line of chain flail equipment and debarking drum followed by a chipper and screening facilities was built up. Equipment and machines for harvesting young stands in a way that increases substantially the yield of energy component are still mostly first prototypes. The development of them into well functioning, efficient tools is the most important task in integrated production

  7. Results of the production of wood derived fuels; Puupolttoaineiden tuotantotekniikka - tutkimusalueen katsaus

    Energy Technology Data Exchange (ETDEWEB)

    Korpilahti, A. [Metsaeteho, Helsinki (Finland)

    1996-12-31

    During the year 1995 there were over 30 projects concerning the production of wood derived fuels going on. Nearly half of them focused on integrated production of pulp wood and wood fuel. About in ten projects work was carried out to promote wood fuel production from logging residues. Other topics were fire wood production, production logistics and wood fuel resources. For production of fuel chips from logging residues, a new chipper truck, MOHA-SISU, was introduced. Having ability to move on terrain, and equipped with drum chipper, hook technic for interchangeable containers and a trailer, the whole production chain can be carried out by the same machine. In Mikkeli region three years of active work promoted the usage of wood fuel in a district power plant to the level of over 110 000 cubic metres of fuel chips. The production costs tend to be a little high in average, and the production chain still needs to be improved. In the field of integrated production a great stride was taken when the first pilot plant using the MASSAHAKE-method started up. Components of the production line and knowledge to operate the process have increased resulting in good performance of the plant. And even another concept for integrated production was introduced. In order to fully control the debarking of small sized trees, a production line of chain flail equipment and debarking drum followed by a chipper and screening facilities was built up. Equipment and machines for harvesting young stands in a way that increases substantially the yield of energy component are still mostly first prototypes. The development of them into well functioning, efficient tools is the most important task in integrated production

  8. Energy wood procurement in connection with conventional wood procurement; Energiapuun hankinnan organisointi muun puunhankinnan yhteydessae - PUUT02

    Energy Technology Data Exchange (ETDEWEB)

    Maekinen, P. [Finnish Forest Research Institute, Vantaa (Finland)

    2001-07-01

    The research consisted of two sub-projects. The present role of forestry associations in procurement of energy wood was investigated in the first sub- project. The possibilities and willingness of them to increase the energy wood procurement were also studied. The role of forest machine and forestry service entrepreneurs in procurement of energy wood was investigated in the second sub-project. The effects of energy wood procurement on the operation of the forest machine companies in general were also studied in this sub-project. The sub-project three studied the requirements of the customer companies for the energy wood suppliers. All the material of the sub-projects was collected by personal inquiries. According to the executive directors of the forestry associations the role of the forestry associations in energy wood procurement varied between a by-stander and active participant. Active forestry associations announced the companies for stands available for cutting. They told also that they directed the harvesting to correct sites and deliver stems at the roadside. The role of the forestry association was emphasised especially when the associations on the basis of a letter of attorney carried out the timber trade. It was estimated that in the near future the operation of forest machine entrepreneurs in harvesting of energy wood would increase significantly. From the employment and turnover point of view the role of harvesting of energy wood was not seen as a significant matter. On the other hand, that harvesting of energy wood impede the harvesting of commercial timber was seen as a more significant matter. In the future the end-users of energy wood would like to have more competition in the energy wood markets. However, the energy wood suppliers were desired to be relative large so that the reliability of deliveries could be ensured. Simultaneously as the end-users wanted to decrease the price of forest chips, the machine entrepreneurs estimated the price to

  9. Wood waste: A disposal problem or an opportunity?

    International Nuclear Information System (INIS)

    Vajda, P.

    1989-01-01

    The utilization of wood wastes in North America is reviewed, with a focus on the wood products industry and markets. On the whole, wood mill residues in North America have always been utilized except for a period from the 1940s to the 1970s oil crisis. In the latter period, low cost electric power and hydrocarbon fuels rendered uneconomical the use of wood wastes as fuel. As a response to the problem of disposing these wastes, a number of innovations occurred in that period, including the use of wood chips for manufacturing pulp and particleboard, and the use of sawdust and shavings for manufacturing hardboard and medium density fiberboard. Uses for bark, except as fuel, have not been successfully developed. Since the 1970s, wood waste in the USA is essentially all used for composite board products and fuel. This is also true in eastern Canada, which is close to the wood products markets and which has fairly high oil and gas costs. However, in western Canada, low energy costs and small internal markets have led to a serious wood waste disposal problem. A survey of wood waste supply and demand shows large surpluses in mill residues in western Canada and some remote locations in northern Ontario and Quebec. The Pacific Rim countries are identified as a potential market for western Canadian composite board production. The use of other sources of wood waste (forestry or logging residues, which are costly to collect, and municipal construction waste) is briefly discussed

  10. World trade in forest products and wood fuel

    International Nuclear Information System (INIS)

    Hillring, Bengt

    2006-01-01

    Wood fuel is a strategic resource for future energy supply and is usually utilised locally. Traditional use of wood fuel and other bioenergy has a share of 10-15% energy supply, used mainly for the household sector. The utilisation for industrial purposes is much smaller but is a strategic resource in the effort to fulfil the Kyoto agreement to replace fossil fuels and to mitigate greenhouse gas emissions. Many industrialised countries already use a significant share of biofuels in their energy supply e.g. Nordic countries while others like some other European Union countries are planning to increase their use. Production and use of biofuels need to be carried out sustainable. Official statistics do not report trade in such detail that international trade in different biomass types can be fully identified. However, FAO and European Forestry Institute are important sources. In some countries, there is a growing interest in the international trade, because the trade can provide biofuels at lower prices, larger quantities and better quality than domestic alternatives. The first signs of an international market price for wood fuel are indicated in Europe. For the future both the use and the trade of wood fuel is expected to increase. Analyses for trade in charcoal, wood chips, fuel wood and wood residues made in this report identify 'hot' trade spots in Europe, in south East Asia and in North America

  11. Western Canadian wood residue production and consumption trends

    International Nuclear Information System (INIS)

    McCloy, B.

    2006-01-01

    This presentation considered various trends in western Canadian wood residue production and consumption. Potential markets for wood residue products were also discussed. Trends were reviewed by province for the years 2000-2004. British Columbia (BC) is currently the largest producer of residue in the country, and also retains the largest surpluses of bark, sawdust and shavings. Wood residues in BC are used in pulp and plywood mill production, as well as in the creation of particleboard and MDF. Surplus mill wood residue production in the province has greatly increased due to the Mountain Pine Beetle (MPB) infestation, which has in turn spurred expansion of the BC interior sawmill industry. The infestation has also resulted in a glut of pulp chips. Current wood residue products in Alberta are mostly used in pulp mill combined heat and power (CHP) systems, as well as for wood pellet production and the creation of particleboard and MDF. It was noted that surplus residues are rapidly declining in the province. Saskatchewan's wood residue storage piles are estimated to contain 2,900,000 BDt, while Manitoba surpluses are relatively minor. It was suggested that high natural gas prices have increased the payback on wood energy systems to approximately 2 years. The value of wood residue is now greater than $100/BDt as a substitute for natural gas once the wood energy system has been fully depreciated. Sawmills may now wish to consider equipping themselves to sell wood residue products, as most sawmills only require 20 per cent of their residues for heating purposes. It was concluded that markets for hog fuel wood pellets should be developed in Canada and internationally. Future markets may also develop if natural gas currently used in pulp mill power boilers and lime kilns is replaced with wood residue energy systems. refs., tabs., figs

  12. Instream wood in a steep headwater channel: geomorphic significance of large and small wood

    Science.gov (United States)

    Galia, Tomáš; Šilhán, Karel; Ruiz-Villanueva, Virginia; Tichavský, Radek

    2016-04-01

    Besides the well-known significance of large wood (LW), also small woody pieces (SW; here defined as pieces with dimensions at least 0.5 m length and 0.05 m diameter), can play an important role in steep narrow headwaters. We inventoried instream wood in the 0.4 km long Mazák headwater channel, Moravskoslezské Beskydy Mts, Czech Republic (2pieces were European beeches (Fagus sylvatica L.); only two pieces were Norway spruces (Picea abies (L.) Karst.). First results showed an increase in the number of LWs in channel-reaches confined by the steepest adjacent hillslopes (especially at 0.15-0.20 km). Increasing downstream amount of SW most likely reflected transport processes in the stream, and the later deposition of SWs on the lowest channel gradients. Also LWs and SWs in the downstream channel-reaches were more decayed than wood presented in the upper reaches. The orientation of instream wood was connected with its length and stability, and LWs longer than 5 m were usually attached to adjacent hillslopes. Pieces longer than 2 m, which were unattached or were somehow stabilized in the channel bed, had often orientation of 0° or 337°. LWs were mostly unattached in the upstream channel-reaches, while often stabilized by adjacent hillslopes in the middle part. At 0.05-0.10 km, there were also many logs stabilized by bed sediments. By contrast, SWs were mostly unattached in the whole longitudinal profile. We observed higher % of influenced channel width by SWs than LWs. Also, SWs were usually entirely located in the channel, which was significantly different when compared to LWs. Nine small steps (step height ~0.5 m) were created by instream wood; six of them were formed by SWs. Dendrogeomorphic cross dating supported the observed decay status for LW/SW within the longitudinal profile: at the lowest channel gradients with wider higher active channels, the potential for storage of instream wood increased. In these downstream reaches we observed older LW and SW, with

  13. Feasibility of Using Rice Hulls as Bedding for Laboratory Mice.

    Science.gov (United States)

    Carbone, Elizabeth T; Kass, Philip H; Evans, Kristin D

    2016-01-01

    Factors that are considered when selecting laboratory mouse bedding include animal health and comfort, cost, effects on personnel, and bioactive properties. Corncob is economical and facilitates low intracage ammonia but has undesirable influences on some endocrine studies. Rice hulls are an economical material that has not been well characterized as a bedding substrate. In this pilot study, we compared various aspects of bedding performance of rice hulls and other materials. On a per-volume basis, rice hulls were less absorbent than was corncob bedding. Rice hulls had higher odds than did corncob or reclaimed wood pulp of having moisture present at the bedding surface. The results of the absorbency tests coupled with the results of preliminary monitoring of intracage ammonia raised concern about the ability of rice hulls to control ammonia levels sufficiently in cages with high occupancy. However, ammonia was negligible when cages contained 5 young adult female mice. The relative expression of 3 cytochrome p450 genes was compared among mice housed on rice hulls, corncob, reclaimed wood pulp, or pine shavings. The expression of Cyp1a2 was 1.7 times higher in the livers of mice housed on rice hulls than on pine shavings, but other differences were not statistically significant. This study provides information on the merits of rice hulls as laboratory mouse bedding. Their relatively poor moisture control is a major disadvantage that might preclude their widespread use.

  14. Effect strooiselmateriaal, strooiselhoeveelheid, opvangschoteltjes en waterdruk op resultaten vleeskuikens = Influence of bedding material, bedding amount, drip cup and reduced water pressure on broiler performance

    NARCIS (Netherlands)

    Harn, van J.; Jong, de I.C.; Veldkamp, T.

    2009-01-01

    Four different bedding materials for broiler houses were compared: white wood shavings, chopped wheat straw, ground rapeseed straw and silage maize. Performance results, carcass yields, litter quality, broiler quality and gait score were measured.

  15. Ecology of the Pinewood Nematode in Southern Pine Chip Piles

    Science.gov (United States)

    L. David Dwinell

    1986-01-01

    The optimum temperature range for pinewood nematodes in southern pine chips was 35 to 40° C. Nematode populations declined at temperatures of -20°C. at temperatures above 45°C. and in anaerobic environments. Wood moisture content and presence of bluestain fungus also influenced nematode populations.

  16. Response surface methodology to simplify calculation of wood energy potency from tropical short rotation coppice species

    Science.gov (United States)

    Haqiqi, M. T.; Yuliansyah; Suwinarti, W.; Amirta, R.

    2018-04-01

    Short Rotation Coppice (SRC) system is an option to provide renewable and sustainable feedstock in generating electricity for rural area. Here in this study, we focussed on application of Response Surface Methodology (RSM) to simplify calculation protocols to point out wood chip production and energy potency from some tropical SRC species identified as Bauhinia purpurea, Bridelia tomentosa, Calliandra calothyrsus, Fagraea racemosa, Gliricidia sepium, Melastoma malabathricum, Piper aduncum, Vernonia amygdalina, Vernonia arborea and Vitex pinnata. The result showed that the highest calorific value was obtained from V. pinnata wood (19.97 MJ kg-1) due to its high lignin content (29.84 %, w/w). Our findings also indicated that the use of RSM for estimating energy-electricity of SRC wood had significant term regarding to the quadratic model (R2 = 0.953), whereas the solid-chip ratio prediction was accurate (R2 = 1.000). In the near future, the simple formula will be promising to calculate energy production easily from woody biomass, especially from SRC species.

  17. Phenolic compounds and sensorial characterization of wines aged with alternative to barrel products made of Spanish oak wood (Quercus pyrenaica Willd.).

    Science.gov (United States)

    Gallego, L; Del Alamo, M; Nevares, I; Fernández, J A; Fernández de Simón, B; Cadahía, E

    2012-04-01

    Wood of Quercus pyrenaica has suitable properties for the wine ageing process. However, the forest available for the barrel making from this particular type of tree is very limited. Nevertheless, it is highly advisable to use this kind of wood in order to manufacture alternative oak products. This study presents the results of ageing the same red wine using different pieces of wood (chips and staves) of Spanish oak (Q. pyrenaica), American oak (Quercus alba) and French oak (Quercus petraea) in conjunction with small, controlled amounts of oxygen. In addition, the phenolic parameters, colour and sensory analysis point out that wines aged with Q. pyrenaica pieces have similar enological characteristics to those aged with American or French oak pieces of wood (chips and staves). Furthermore, the total oxygen consumed and its relation with sensory properties also has been studied in this article in order to know how the oxygen behaves in these processes. Besides, it is going to put forward the fact that chips and staves from Q. pyrenaica oak are suitable for the ageing of red wines and better considered than American or French ones, showing higher aromatic intensity, complexity, woody, balsamic and cocoa. Finally, the tasters valued highly the wines with staves, pointing out its flavour and roundness in mouth.

  18. Bed mixing dryer for high moisture content fuels

    Energy Technology Data Exchange (ETDEWEB)

    Hulkkonen, S; Heinonen, O. [Imatran Voima Oy, Vantaa (Finland)

    1998-12-31

    Bed mixing dryer is a new type of fuel drying technology for fluidized bed combustion. The idea is to extract hot bed material from the fluidized bed and use it as a heat source for drying the fuel. Drying occurs at steam atmosphere which makes it possible to recover the latent heat of evaporation to process. This improves the thermal efficiency of the power plant process considerably, especially in combined heat and power applications. Imatran Voima Oy (IVO) has developed the Bed Mixing Dryer technology since early 1990s. The first pilot plant was built in 1994 to IVO`s Kuusamo peat and wood fired power plant. The capacity of the plant is 6 MW{sub e} and 20 MW of district heat. In Kuusamo the dryer is connected to a bubbling fluidized bed. Since it`s commissioning the dryer has been used successfully for about 3000 hours during the heating season in wintertime. The second application of the technology will be a demonstration project in Oerebro (S). IVO Power Engineering Ltd will supply in 1997 a dryer to Oerebro Energi`s peat, wood and coal fired CHP plant equipped with circulating fluidized bed boiler. The fuel to be dried is sawdust with fuel input of about 60 MW. In Kuusamo the dryer produces 3 MW of additional district heat and in Oerebro 6 MW. The fuels in Kuusamo are peat, saw dust and bark. In addition to the municipal heat production this type of drying technology has its benefits in pulp and paper industry processes. Disposal of paper mill sludges is becoming more difficult and costly which has resulted in need of alternative treatment. Drying of the sludge before combustion in a boiler for power production is an attractive option. At the moment IVO is carrying out several studies to apply the Bed Mixing Dryer in pulp and paper industry processes. Economy of drying the sludge looks promising

  19. Bed mixing dryer for high moisture content fuels

    Energy Technology Data Exchange (ETDEWEB)

    Hulkkonen, S.; Heinonen, O. [Imatran Voima Oy, Vantaa (Finland)

    1997-12-31

    Bed mixing dryer is a new type of fuel drying technology for fluidized bed combustion. The idea is to extract hot bed material from the fluidized bed and use it as a heat source for drying the fuel. Drying occurs at steam atmosphere which makes it possible to recover the latent heat of evaporation to process. This improves the thermal efficiency of the power plant process considerably, especially in combined heat and power applications. Imatran Voima Oy (IVO) has developed the Bed Mixing Dryer technology since early 1990s. The first pilot plant was built in 1994 to IVO`s Kuusamo peat and wood fired power plant. The capacity of the plant is 6 MW{sub e} and 20 MW of district heat. In Kuusamo the dryer is connected to a bubbling fluidized bed. Since it`s commissioning the dryer has been used successfully for about 3000 hours during the heating season in wintertime. The second application of the technology will be a demonstration project in Oerebro (S). IVO Power Engineering Ltd will supply in 1997 a dryer to Oerebro Energi`s peat, wood and coal fired CHP plant equipped with circulating fluidized bed boiler. The fuel to be dried is sawdust with fuel input of about 60 MW. In Kuusamo the dryer produces 3 MW of additional district heat and in Oerebro 6 MW. The fuels in Kuusamo are peat, saw dust and bark. In addition to the municipal heat production this type of drying technology has its benefits in pulp and paper industry processes. Disposal of paper mill sludges is becoming more difficult and costly which has resulted in need of alternative treatment. Drying of the sludge before combustion in a boiler for power production is an attractive option. At the moment IVO is carrying out several studies to apply the Bed Mixing Dryer in pulp and paper industry processes. Economy of drying the sludge looks promising

  20. Abatement cost of GHG emissions for wood-based electricity and ethanol at production and consumption levels.

    Directory of Open Access Journals (Sweden)

    Puneet Dwivedi

    Full Text Available Woody feedstocks will play a critical role in meeting the demand for biomass-based energy products in the US. We developed an integrated model using comparable system boundaries and common set of assumptions to ascertain unit cost and greenhouse gas (GHG intensity of electricity and ethanol derived from slash pine (Pinus elliottii at the production and consumption levels by considering existing automobile technologies. We also calculated abatement cost of greenhouse gas (GHG emissions with respect to comparable energy products derived from fossil fuels. The production cost of electricity derived using wood chips was at least cheaper by 1 ¢ MJ-1 over electricity derived from wood pellets. The production cost of ethanol without any income from cogenerated electricity was costlier by about 0.7 ¢ MJ-1 than ethanol with income from cogenerated electricity. The production cost of electricity derived from wood chips was cheaper by at least 0.7 ¢ MJ-1 than the energy equivalent cost of ethanol produced in presence of cogenerated electricity. The cost of using ethanol as a fuel in a flex-fuel vehicle was at least higher by 6 ¢ km-1 than a comparable electric vehicle. The GHG intensity of per km distance traveled in a flex-fuel vehicle was greater or lower than an electric vehicle running on electricity derived from wood chips depending on presence and absence of GHG credits related with co-generated electricity. A carbon tax of at least $7 Mg CO2e-1 and $30 Mg CO2e-1 is needed to promote wood-based electricity and ethanol production in the US, respectively. The range of abatement cost of GHG emissions is significantly dependent on the harvest age and selected baseline especially for electricity generation.

  1. Lab and Bench-Scale Pelletization of Torrefied Wood Chips

    DEFF Research Database (Denmark)

    Shang, Lei; Nielsen, Niels Peter K.; Stelte, Wolfgang

    2013-01-01

    Combined torrefaction and pelletization is used to increase the fuel value of biomass by increasing its energy density and improving its handling and combustion properties. In the present study, a single-pellet press tool was used to screen for the effects of pellet die temperature, moisture cont...... of the torrefied pellets was higher and the particle size distribution after grinding the pellets was more uniform compared to conventional wood pellets....

  2. Wood torrefaction. Pilot tests and utilisation prospects

    Energy Technology Data Exchange (ETDEWEB)

    Wilen, C.; Jukola, P.; Jarvinen, T.; Sipila, K. [VTT Technical Reseach Centre of Finland, Espoo (Finland); Verhoeff, F.; Kiel, J. [Energy research Centre of the Netherlands, LE Petten (Netherlands)

    2013-09-15

    The research project 'Torrefaction of woody biomasses as energy carriers for the European markets' was carried out within the Tekes BioRefine programme in 2010-2012 and was coordinated by VTT. The main objective of the project was to create a discussion platform and collate basic information for the Finnish industrial stakeholders involved in developing torrefaction technology or planning to include torrefied biomass in their fuel supply for energy production. Given the availability of torrefaction pilot facilities in Europe, it was decided at an early phase of the national torrefaction research project not to build and operate separate pilot equipment, and thus save time and money. Experimental research was conducted in cooperation with ECN, The Netherlands. Finnish wood chips and crushed forest residue were tested at different torrefaction temperatures in the PATRIG torrefaction test rig with great success, and large quantities of torrefied wood chips and pellets were produced. CFD simulation work was carried out at VTT to investigate the feasibility of torrefied fuels to replace part of the coal. From the combustion point of view it seems feasible to replace coal by torrefied wood biomass with shares up to 50% by weight. Basic, small-scale experiments were carried out to compare torrefied wood pellets with conventional wood and straw pellets with regard to their handling and storage properties. The experiments showed that the torrefied pellets are clearly more hydrophobic than wood and straw pellets and do not disintegrate completely on exposure to water. A study on dust explosion and self-ignition characteristics indicated that the torrefied dust does not differ significantly from the normal biomass dust, but is clearly more reactive than coal dust. Commercial development of torrefaction is currently in its early phase. The current general view is that most of the demonstration plants have technical problems, which have delayed their commercial

  3. Activity concentrations of radionuclides in energy production from peat, wood chips and straw

    Science.gov (United States)

    Hedvall, Robert Hans

    1997-11-01

    In this thesis quantitative analyses of radionuclide concentrations in bioenergy fuels such as peat, wood chips and straw are presented. For comparison a brief description is included of radionuclide concentrations and radiation doses from other sources of power and also from some industrial applications. Radiation is a natural phenomenon and radionuclides occur naturally. The first man-made spread of concentrated radioactivity occurred some 100,000 years ago when the first fireplace was lit, with fallout as a later consequence. Radioactive potassium is found in most materials and is the most easily detected nuclide in fuels. Its activity concentration in Bq kg-1 normally dominates over the concentration of other natural radionuclides. The radiation dose from potassium in the emission is nevertheless negligible. The most important radionuclides in the dose to humans are the U- and Th-isotopes and also 210Pb and 210Po. Of fission products in fallout from the atmospheric nuclear tests and after the Chernobyl accident, 137Cs was shown to be the most common nuclide. Compared to natural nuclides, the contribution from emission of 137Cs was shown to be the most common nuclide. Compared to natural nuclides, the contribution from emission of 137Cs is less than a few percent of the total dose to the population. A total dose of approximately a few μSv from inhalation only can be calculated from the emission of a district heating plant in Sweden. This dose can be compared with the annual dose limit to the public from nuclear industry, which is 0.1 mSv and the global collective effective dose of 5 person Sv a-1.

  4. Dry Matter Losses and Greenhouse Gas Emissions From Outside Storage of Short Rotation Coppice Willow Chip.

    Science.gov (United States)

    Whittaker, Carly; Yates, Nicola E; Powers, Stephen J; Misselbrook, Tom; Shield, Ian

    This study examined the dry matter losses and the greenhouse gas (GHG) concentrations within two short rotation coppice (SRC) willow wood chip storage heaps. One heap was built on a grassland area (East Midlands) and the other (Rothamsted) on a concrete hard standing. A series of 1- and 3-m probes were embedded in the heaps in order to retrieve gas samples for analysis, and pre-weighed net bags were positioned in the core of the heap to detect dry matter losses. The bagged samples showed dry matter losses of 18 and 19 % in the East Midlands and Rothamsted heaps after 210 and 97 days storage, respectively. The Rothamsted heap showed a whole-heap dry matter loss of 21 %. During this time, the wood chips dried from 54 to 39 % moisture content in the East Midlands heap and 50 to 43 % at Rothamsted. The results from analysing the whole Rothamsted heap indicated an overall loss of 1.5 GJ per tonne stored, although measurements from bagged samples in the core suggested that the chips dried sufficiently to have a minimal energy loss from storage. The process of mixing the heap, however, led to incorporation of wet outer layers and hence the average moisture content was higher in an average sample of chip. After establishment of the heaps, the temperature rose rapidly and this correlated with a peak in carbon dioxide (CO 2 ) concentration within the heap. A peak in methane (CH 4 ) concentration was also detected in both heaps, though more noticeably in the East Midlands heap after around 55 days. In both instances, the peak CH 4 concentration occurred as CO 2 concentrations dropped, suggesting that after an active period of aerobic decomposition in the first 2 months of storage, the conditions in the heap became anaerobic. The results from this study suggest that outside wood chip storage is not an efficient method of storing biomass, though this may be location-specific as there are some studies showing lower dry matter losses. It is necessary to explore other

  5. Electrodialytic remediation of CCA treated waste wood in pilot scale

    DEFF Research Database (Denmark)

    Pedersen, Anne Juul; Christensen, Iben Vernegren; Ottosen, Lisbeth M.

    2005-01-01

    study the utility of the method Electrodialytic Remediation was demonstrated for handling of CCA treated waste wood in pilot scale. The electrodialytic remediation method, which uses a low level DC current as the cleaning agent, combines elektrokinetic movement of ions in the wood matrix with the princi......-ples of electrodialysis. It has previously been shown that it is possible to remove Cu, Cr and As from CCA treated wood using electrodialytic remediation in laboratory scale (Ribeiro et al., 2000; Kristensen et al., 2003), but until now, the method had not been studied in larger scale. The pilot scale plant used...... in this study was designed to contain up to 2 m3 wood chips. Six remediation experiments were carried out. In these experiments, the process was up-scaled stepwise by increasing the distance between the electrodes from initially 60 cm to fi-nally 150 cm. The remediation time was varied between 11 and 21 days...

  6. Analysis of existing structure and emissions of wood combustion plants for the production of heat and electricity in Bavaria

    International Nuclear Information System (INIS)

    Joa, Bettina

    2014-01-01

    This work deals with the detailed analysis of the existing structure of all Bavarian wood burning plants for the generation of heat and electricity as well as the determination of the resulting emission emissions in 2013. The number of wood burning plants in the single-chamber fireplaces, wood central heating and wood-fired heating plants which are in operation in the year 2013 were determined, and how many plants are existing in the various areas like pellet stoves, traditional ovens, wood-burning fireplace, pellet central heating systems, wood chips central heating systems, fire-wood central heating systems, wood combined heat and power plant (electricity and heat) and wood power plants (heat). In addition, the regional distribution of the wood burning plants in the Bavarian governmental districts is investigated as well as the type and amount of energy produced by them (heat, electricity). [de

  7. Wood Pulp Digetster Wall Corrosion Investigation

    Energy Technology Data Exchange (ETDEWEB)

    Giles, GE

    2003-09-18

    The modeling of the flow in a wood pulp digester is but one component of the investigation of the corrosion of digesters. This report describes the development of a Near-Wall-Model (NWM) that is intended to couple with a CFD model that determines the flow, heat, and chemical species transport and reaction within the bulk flow of a digester. Lubrication theory approximations were chosen from which to develop a model that could determine the flow conditions within a thin layer near the vessel wall using information from the interior conditions provided by a CFD calculation of the complete digester. The other conditions will be determined by coupled solutions of the wood chip, heat, and chemical species transport and chemical reactions. The NWM was to couple with a digester performance code in an iterative fashion to provide more detailed information about the conditions within the NW region. Process Simulations, Ltd (PSL) is developing the digester performance code. This more detailed (and perhaps more accurate) information from the NWM was to provide an estimate of the conditions that could aggravate the corrosion at the wall. It is intended that this combined tool (NWM-PSL) could be used to understand conditions at/near the wall in order to develop methods to reduce the corrosion. However, development and testing of the NWM flow model took longer than anticipated and the other developments (energy and species transport, chemical reactions and linking with the PSL code) were not completed. The development and testing of the NWM are described in this report. In addition, the investigation of the potential effects of a clear layer (layer reduced in concentration of wood chips) near the wall is reported in Appendix D. The existence of a clear layer was found to enhance the flow near the wall.

  8. Startup and long-term performance of biotrickling filters packed with polyurethane foam and poplar wood chips treating a mixture of ethylmercaptan, H2S, and NH3.

    Science.gov (United States)

    Hernández, J; Lafuente, J; Prado, O J; Gabriel, D

    2013-04-01

    Treatment of a mixture of NH3, H2S, and ethylmercaptan (EM) was investigated for more than 15 months in two biotrickling filters packed with poplar wood chips and polyurethane foam. Inlet loads ranging from 5 to 10 g N-NH3 m-3 hr-1, from 5 to 16 g S-H2S m-3 hr-1, and from 0 to 5 g EM m-3 hr-1 were applied. During startup, the biotrickling filter packed with polyurethane foam was re-inoculated due to reduced biomass retention as well as a stronger effect of nitrogen compounds inhibition compared with the biotrickling filter packed with poplar wood. Accurate pH control between 7 and 7.5 favored pollutants abatement. In the long run, complete NH3 removal in the gas phase was achieved in both reactors, while H2S removal efficiencies exceeded 90%. EM abatement was significantly different in both reactors. A systematically lower elimination capacity was found in the polyurethane foam bioreactor. N fractions in the liquid phase proved that high nitrification rates were reached throughout steady-state operation in both bioreactors. CO2 production showed the extent of the organic packing material degradation, which allowed estimating its service lifetime in around 2 years. In the long run, the bioreactor packed with the organic packing material had a lower stability. However, an economic analysis indicated that poplar wood chips are a competitive alternative to inorganic packing materials in biotrickling filters. We provide new insights in the use of organic packing materials in biotrickling filters for the treatment of H2S, NH3, and mercaptans and compare them with polyurethane foam, a packing commonly used in biotrickling filters. We found interesting features related with the startup of the reactors and parameterized both the performance under steady-state conditions and the influence of the gas contact time. We provide relevant conclusions in the profitability of organic packing materials under a biotrickling filter configuration, which is infrequent but proven reliable

  9. Processing of the wood angelim pedra (Hymenolobium petraeum

    Directory of Open Access Journals (Sweden)

    Adjenane Corrêa Taques

    2016-08-01

    Full Text Available This study aimed to verify the behavior of wood Angelim stone (Hymenolobium petraeum Ducke submitted to the machining process. The study was developed in a carpentry shop in the city of Alta Floresta-MT. 36 boards with dimensions of 150 cm x 13.5 cm x 2.5 cm, length, width and thickness were randomly selected respectively for machining tests. The tests were developed according to the machinability of equipment used by the furniture industry, planing, sanding, drill and split by nail. 8 boards of wood in the stack were selected randomly to determine the moisture, according to 7190 (ABNT, 1997. The notes used for evaluation of defects resulting in the wood during the machining processes were assigned according to ASTM D 1666 (1987. It was observed that the type of angelim stone showed excellent performance in grinding tests, no scratch on the surface piece a of the burring parts and the parts free from defects, with the burning of wood. In cracking test for nail had a good performance, because it showed cracks with the insertion of the nail and planing test a regular performance, with pullout grain, surface arrepiamento and pullout chip. Wood Angelim stone responds with quality to the machining processes in planing, sanding, drill and split by nail.

  10. Aeration to improve biogas production by recalcitrant feedstock

    Science.gov (United States)

    Much agricultural waste is largely composed of polymers such as lignin and complex carbohydrates that are slowly or nearly completely non-degradable in anaerobic environments. An example of such a waste is chicken litter in which wood chips, rice hulls, and sawdust are commonly employed bedding mate...

  11. Prevention of Bed Agglomeration Problems in a Fluidized Bed Boiler by Finding the Trigging Value of Sewage Sludge Dosage Added to Combustion of Biofuels

    Energy Technology Data Exchange (ETDEWEB)

    Andersson, Kajsa; Gervind, Pernilla

    2009-07-01

    Agglomeration of bed sand is a common problem during combustion of biofuels with high ash content in fluidized bed boilers. Former studies have shown that co-combustion of biofuels with sewage sludge increases the agglomeration temperature. Sewage sludge has a low heating value and high ash content. It would therefore be better to use sludge as an additive to the combustion than as a co-combusted biofuel. In this study the trigging value of sludge addition to the combustion of some biofuel was investigated. The effect of adding sludge with different precipitation chemicals, iron sulphate and aluminium sulphate, was investigated. The biofuels used for the experiments were bark, refused derived fuel (RDF) and a mixture of wood and straw, 75/25 % on energy basis. All experiments were carried out in a laboratory scale fluidized bed reactor. Analyses of chemical composition of bed sand and SEM/EDX analyses were performed after the combustion. Eventually agglomeration tests were performed in order to find the agglomeration temperature of the samples. Some of the samples sintered during the combustion and were not tested for the agglomeration temperature. SEM/EDX showed that all samples of bed sand contained sand particles with more or less coatings. In some cases the coatings seemed to consist of one dense inner layer and one more porous outer layer. From SEM/EDX and chemical composition analyses it was found that the total amount of phosphorous in the bed sand samples was increased with an increased addition of sludge in all experiments. The concentration of phosphorous was especially higher in the outer layers/coatings. It was also found that elements from the sludge seem to get caught by a sticky layer at the bed sand surface and form a non-sticky or less sticky layer that prevents agglomeration. The total amount of aluminium was increased with an increased addition of sludge for the wood/straw samples, while it increased with an increased amount of combusted fuel for

  12. Buried chip skin grafting in neuropathic diabetic foot ulcers following vacuum-assisted wound bed preparation: enhancing a classic surgical tool with novel technologies.

    Science.gov (United States)

    Kopp, Jürgen; Kneser, Ulrich; Bach, Alexander D; Horch, Raymund E

    2004-09-01

    In patients with diabetes mellitus, complications such as polyneuropathy and peripheral angiopathy inevitably lead to diabetic foot complications including foot ulcers, gangrene, and osteoarthropathy. These conditions necessitate minor or major amputation as part of treatment. In patients with Charcot's arthropathy and predominant neuropathy, recurrent foot ulcers are common in areas of high pressure. Such high pressure is caused by the degrading of the architecture of the foot and inadequate footwear. These patients are a clinical challenge. A select group of such patients may benefit from free surgical tissue transfer, though free or local flap surgery is often difficult or even impossible owing to an impaired arterial circulation. In such wounds, surgical debridement followed by skin grafts often fail due to bacterial burden in the wounds. To circumvent these problems, the authors developed a therapeutic approach using buried chip skin grafting to close granulation wound beds in diabetic feet. Locally applied vacuum therapy (VAC) for wound bed preparation of chronic, nonresponsive foot ulcers and subsequent grafting using the burying technique with a minute fraction of skin was used. Firm closure was achieved. The closed wound was resistant to mechanical irritation.

  13. Pyrolysis of softwood carbohydrates in a fluidized bed reactor.

    Science.gov (United States)

    Aho, Atte; Kumar, Narendra; Eränen, Kari; Holmbom, Bjarne; Hupa, Mikko; Salmi, Tapio; Murzin, Dmitry Yu

    2008-09-01

    In the present work pyrolysis of pure pine wood and softwood carbohydrates, namely cellulose and galactoglucomannan (the major hemicellulose in coniferous wood), was conducted in a batch mode operated fluidized bed reactor. Temperature ramping (5 degrees C/min) was applied to the heating until a reactor temperature of 460 degrees C was reached. Thereafter the temperature was kept until the release of non-condensable gases stopped. The different raw materials gave significantly different bio-oils. Levoglucosan was the dominant product in the cellulose pyrolysis oil. Acetic acid was found in the highest concentrations in both the galactoglucomannan and in the pine wood pyrolysis oils. Acetic acid is most likely formed by removal of O-acetyl groups from mannose units present in GGM structure.

  14. Machinery for Forest Chip Production in Finland in 2007 and in the Future

    Energy Technology Data Exchange (ETDEWEB)

    Kaerhae, Kalle (Metsaeteho Oy, P.O. Box 101, FI-00171 Helsinki (Finland))

    2008-10-15

    Metsaeteho Oy's study consisted of a survey of the production machinery for forest chips used by energy plants in 2007. The major forest chip suppliers in Finland were involved in the study. In addition, the machinery and equipment stocked by the manufacturers and vendors of energy wood harvester heads, stump lifting devices, and chippers were also surveyed. The study provided also an estimate of future machinery requirements for forest chip production in Finland. The study estimated that a total of 1,100 machine and truck units were employed in the production of forest chips for energy plants in 2007. A total of 770 machine and truck units were contracted for the major forest chip suppliers in 2007. Increasing forest chip consumption will considerable increase the demand for additional forest chip production resources in the future. If the consumption of forest chips by energy plants in 2015 reaches 15 TWh, i.e. about 7.5 mill. m3, then the forest machine and truck requirement will be over 1,700 units. The corresponding machinery requirement at an energy plant with a forest chip consumption of 25 TWh (approx. 12.5 mill. m3), will be close to 2,300 machine and truck units

  15. Performance of Schizolobium amazonicum Wood in Bleached Kraft Pulp Production

    Directory of Open Access Journals (Sweden)

    Camila Sarto

    2015-05-01

    Full Text Available This study aimed to evaluate the characteristics of Schizolobium amazonicum wood, specifically its performance in bleached kraft pulp production and the characteristics of its pulp. Chips of Schizolobium amazonicum and Eucalyptus grandis x Eucalyptus urophylla (reference were used. The following parameters were evaluated in the wood: basic density, total extractives, total lignin, holocellulose, and fiber morphology. The pulping simulations were carried out in a laboratory digester, with parameters set to obtain pulp with kappa number 19 ± 0.5. Both pulps were bleached in a PFI mill and submitted to physical-mechanical tests. The results showed that S. amazonicum wood has low basic density and higher content of extractives when compared to E. grandis x E. urophylla wood. For pulping, S. amazonicum required higher alkali charge and H factor to achieve the same delignification level of E. grandis x E. urophylla, resulting in a lower yield, pulp with lower viscosity, and higher wood specific consumption. During bleaching, the brightness gain and final viscosity of S. amazonicum pulp were lower than E. grandis x E. urophylla pulp. Moreover, S. amazonicum pulp had worse physical-mechanical characteristics than E. grandis x E. urophylla.

  16. Test Firing of chunk wood - Is it possible to automate the fuel supply?; Proveldning av knubbved - Aer det moejligt att automatisera braenslematningen?

    Energy Technology Data Exchange (ETDEWEB)

    Persson, Tomas; Danielsson, Bengt-Olof

    2013-05-15

    Chunk wood is a wood fuel with a fuel particle length typically between 50 and 150 mm. The ad-vantage of chunk wood compared to wood chips is that the fuel dry as fast as fuel wood, but can be produced and handled as wood chip. Technologies for efficient producing, drying and distribution of Chunk wood have been developed since the 1970:s and machines for manufacturing the fuel is available on the market, but still there is no small-scale heating equipment in operation to burn the fuel automatically. The aim of the study was to investigate how the feeding and firing of chunk wood works in a standard 200 kW biomass boiler for various types of biofuels. The main focus was on studying how the fuel feeding system works using chunk wood and if the combustion and emissions are satisfactory. The boiler have a main fuel feeding auger screw connected to the bottom of the fuel storage, followed by a cell feeder and another auger screw that is feeding the fuel into the combustion chamber. The power consumption for the fuel feeding auger screws and the CO-emissions were measured during the firing period. In order to obtain reference values for the stresses in the fuel feeding system and the CO-emissions, regular wood chips were initially fired followed by the chunk wood firing. During the chunk wood firing period several interruptions in the fuel feeding occurred, as the trigger mechanism for the motor protection stopped the fuel supply. Most of the interruptions, however, could be resolved through manual reversing of the fuel feeding auger screw. Only at two occasions the entrance to the auger screw were manually cleared from large fuel pieces. The cell feeder and the auger screw feeding the fuel into the combustion chamber were stopped twice, and to continue operating the boiler it was enough to restart the feeding system. However, as they are both operated by the same motor we do not know whether the two shutdowns that occurred were caused by feeding problems in the auger

  17. Assessment of wood-inhabiting Basidiomycetes for biokraft pulping of softwood chips

    CSIR Research Space (South Africa)

    Wolfaardt, F

    2004-10-01

    Full Text Available Wood-inhabiting Basidiomycetes have been screened for various applications in the pulp and paper industry and it is evident that different fungi need to be used to suit the specific requirements of each application. This study assessed...

  18. Wood pellets for stoker burner

    International Nuclear Information System (INIS)

    Nykaenen, S.

    2000-01-01

    The author of this article has had a stoker for several years. Wood chips and sod peat has been used as fuels in the stoker, either separately or mixed. Last winter there occurred problems with the sod peat due to poor quality. Wood pellets, delivered by Vapo Oy were tested in the stoker. The price of the pellets seemed to be a little high 400 FIM/500 kg large sack. If the sack is returned in good condition 50 FIM deposit will be repaid to the customer. However, Vapo Oy informed that the calorific value of wood pellets is three times higher than that of sod peat so it should not be more expensive than sod peat. When testing the wood pellets in the stoker, the silo of the stoker was filled with wood pellets. The adjustments were first left to position used for sod peat. However, after the fire had ignited well, the adjustments had to be decreased. The content of the silo was combusted totally. The combustion of the content of the 400 litter silo took 4 days and 22 hours. Respectively combustion of 400 l silo of good quality sod peat took 2 days. The water temperature with wood pellets remained at 80 deg C, while with sod peat it dropped to 70 deg C. The main disadvantage of peat with small loads is the unhomogenous composition of the peat. The results of this test showed that wood pellets will give better efficiency than peat, especially when using small burner heads. The utilization of them is easier, and the amount of ash formed in combustion is significantly smaller than with peat. Wood pellets are always homogenous and dry if you do not spoil it with unproper storage. Pellets do not require large storages, the storage volume needed being less than a half of the volume needed for sod peat. When using large sacks the amount needed can even be transported at the trunk of a passenger car. Depending on the area to be heated, a large sack is sufficient for heating for 2-3 weeks. Filling of stoker every 2-5 day is not an enormous task

  19. Tectonic setting of the Wooded Island earthquake swarm, eastern Washington

    Science.gov (United States)

    Blakely, Richard J.; Sherrod, Brian L.; Weaver, Craig S.; Rohay, Alan C.; Wells, Ray E.

    2012-01-01

    Magnetic anomalies provide insights into the tectonic implications of a swarm of ~1500 shallow (~1 km deep) earthquakes that occurred in 2009 on the Hanford site,Washington. Epicenters were concentrated in a 2 km2 area nearWooded Island in the Columbia River. The largest earthquake (M 3.0) had first motions consistent with slip on a northwest-striking reverse fault. The swarm was accompanied by 35 mm of vertical surface deformation, seen in satellite interferometry (InSAR), interpreted to be caused by ~50 mm of slip on a northwest-striking reverse fault and associated bedding-plane fault in the underlying Columbia River Basalt Group (CRBG). A magnetic anomaly over exposed CRBG at Yakima Ridge 40 km northwest of Wooded Island extends southeastward beyond the ridge to the Columbia River, suggesting that the Yakima Ridge anticline and its associated thrust fault extend southeastward in the subsurface. In map view, the concealed anticline passes through the earthquake swarm and lies parallel to reverse faults determined from first motions and InSAR data. A forward model of the magnetic anomaly near Wooded Island is consistent with uplift of concealed CRBG, with the top surface swarm and the thrust and bedding-plane faults modeled from interferometry all fall within the northeastern limb of the faulted anticline. Although fluids may be responsible for triggering the Wooded Island earthquake swarm, the seismic and aseismic deformation are consistent with regional-scale tectonic compression across the concealed Yakima Ridge anticline.

  20. Effect of ploughing-down of grapevine chips on soil structure when using special agricultural machinery

    Directory of Open Access Journals (Sweden)

    Barbora Badalíková

    2012-01-01

    Full Text Available Within the period of 2008–2011, changes in soil structure were studied in two selected localities: one of them was situated in vineyards of the University Training Farm of Mendel University in Žabčice near Brno, the other was in vineyards situated in the cadastre of wine-growing municipality Velké Bílovice. Established were altogether three variants of experiments with application of crushed grapevine wood (chips: Variant 1 – control; Variant 2 – crushed grapevine wood ploughed down to the depth of 0.10 m; Variant 3 – crushed grapevine wood + grass spread on the soil surface as a mulch. Grapevine canes were crushed to chips using a special agricultural machinery while the soil in inter-rows was processed using conventional tilling machines. The obtained results showed that the best coefficient of structurality (expressing the degree of destruction of soil structure was recorded in Variants 2 in both localities. Considering values of this coefficient it could be concluded that just this variant showed a positive effect on soil structure. This variant reduced the compaction of soil caused by the movement of agricultural machines in vineyard inter-rows Crushed grapevine waste wood can therefore compensate losses of organic matter in soil. Better values of structurality coefficient were recorded in the locality Žabčice.

  1. Evaluation of ecological impacts of synthetic natural gas from wood used in current heating and car systems

    Energy Technology Data Exchange (ETDEWEB)

    Felder, Remo; Dones, Roberto [Paul Scherrer Institut, 5232 Villigen PSI (Switzerland)

    2007-06-15

    A promising option to substitute fossil energy carriers by renewables is the production of synthetic natural gas (SNG) from wood, as this results in a flexible energy carrier usable via existing infrastructure in gas boilers or passenger cars. The comprehensive life cycle-based ecological impact of SNG is investigated and compared with standard fuels delivering the same service (natural gas, fuel oil, petrol/diesel, and wood chips). Life cycle impact assessment methodologies and external costs from airborne emissions provide measures of overall damage. The results indicate that the SNG system has the best ecological performance if the consumption of fossil resources is strongly weighted. Otherwise natural gas performs best, as its supply chain is energy-efficient and its use produces relatively low emissions. Wood systems are by far the best in terms of greenhouse gas emissions (GHG), where SNG emits about twice as much as the wood chips system. The main negative aspects of the SNG system are NO{sub x} and particulate emissions and the relatively low total energy conversion efficiency resulting from the additional processing to transform wood to gas. Direct wood combustion has a better ecological score when highly efficient particulate filters are installed. SNG performs better than oil derivatives with all the evaluation methods used. External costs for SNG are the lowest as long as GHG are valued high. SNG should preferably be used in cars, as the reduction of overall ecological impacts and external costs when substituting oil-based fuels is larger for current cars than for heating systems. (author)

  2. Wood chip drying in connection with combined heat and power or solar energy in Finland

    Directory of Open Access Journals (Sweden)

    Rinne Samuli

    2014-01-01

    Full Text Available 20% of the Finnish district heating (DH power plant fuels are wood-based and the share is increasing. The wood fuel demand probably exceeds the potential supply in the future. The wood fuel drying with waste heat is one profitable opportunity to gain more wood fuel. If the drying energy can be produced with lower primary energy use than combusting the fuel directly, the drying potentially improves the system efficiency. In this study, the drying feasibility in the connection of a combined heat and power (CHP system, possibly with solar collectors, is calculated. The wood fuel heating can be increased profitably by 6%, using the heat from CHP for drying only when the marginal cost of the heat is low enough, i.e. the electricity price is high enough and there is free capacity after the DH demand. Although the drying is profitable, a larger heat storage can also increase the annual result similarly. The best investment choice depends on the plant properties. Here the optimal system enables 20% DH production cost savings. Solar heat may be profitable, when the solar heat has a 2–3% share of the annual heat demand. However, the dryer or larger storage tank are more profitable investments.

  3. Effect of temperature in fluidized bed fast pyrolysis of biomass: oil quality assessment in test units

    NARCIS (Netherlands)

    Westerhof, Roel Johannes Maria; Brilman, Derk Willem Frederik; van Swaaij, Willibrordus Petrus Maria; Kersten, Sascha R.A.

    2010-01-01

    Pine wood was pyrolyzed in a 1 kg/h fluidized bed fast pyrolysis reactor that allows a residence time of pine wood particles up to 25 min. The reactor temperature was varied between 330 and 580 °C to study the effect on product yields and oil composition. Apart from the physical−chemical analysis, a

  4. Development of a trickle bed reactor of electro-Fenton process for wastewater treatment.

    Science.gov (United States)

    Lei, Yangming; Liu, Hong; Shen, Zhemin; Wang, Wenhua

    2013-10-15

    To avoid electrolyte leakage and gas bubbles in the electro-Fenton (E-Fenton) reactors using a gas diffusion cathode, we developed a trickle bed cathode by coating a layer composed of carbon black and polytetrafluoroethylene (C-PTFE) onto graphite chips instead of carbon cloth. The trickle bed cathode was optimized by single-factor and orthogonal experiments, in which carbon black, PTFE, and a surfactant were considered as the determinant of the performance of graphite chips. In the reactor assembled by the trickle bed cathode, H2O2 was generated with a current of 0.3A and a current efficiency of 60%. This performance was attributed to the fine distribution of electrolyte and air, as well as the effective oxygen transfer from the gas phase to the electrolyte-cathode interface. In terms of H2O2 generation and current efficiency, the developed trickle bed reactor had a performance comparable to that of the conventional E-Fenton reactor using a gas diffusion cathode. Further, 123 mg L(-1) of reactive brilliant red X-3B in aqueous solution was decomposed in the optimized trickle bed reactor as E-Fenton reactor. The decolorization ratio reached 97% within 20 min, and the mineralization reached 87% within 3h. Copyright © 2013 Elsevier B.V. All rights reserved.

  5. Pyrolysis of Softwood Carbohydrates in a Fluidized Bed Reactor

    Directory of Open Access Journals (Sweden)

    Dmitry Yu. Murzin

    2008-09-01

    Full Text Available In the present work pyrolysis of pure pine wood and softwood carbohydrates, namely cellulose and galactoglucomannan (the major hemicellulose in coniferous wood, was conducted in a batch mode operated fluidized bed reactor. Temperature ramping (5°C/min was applied to the heating until a reactor temperature of 460 °C was reached. Thereafter the temperature was kept until the release of non-condensable gases stopped. The different raw materials gave significantly different bio-oils. Levoglucosan was the dominant product in the cellulose pyrolysis oil. Acetic acid was found in the highest concentrations in both the galactoglucomannan and in the pine wood pyrolysis oils. Acetic acid is most likely formed by removal of O-acetyl groups from mannose units present in GGM structure.

  6. Production rates and costs of cable yarding wood residue from clearcut units

    Science.gov (United States)

    Chris B. LeDoux

    1984-01-01

    Wood residue is a little used source of fiber, chips, and fuel because harvest costs are largely unknown. This study calculates incremental production rates and costs for yarding and loading logging residue in clearcut old-growth Douglas-fir/western hemlock forests. Harvest operations were observed for two timber sales in western Oregon. Three different cable yarding...

  7. Environmental assessment of domestic wood heating

    International Nuclear Information System (INIS)

    Labouze, E.; Le Guerin, Y.

    2009-01-01

    In France, more than 6 million families are concerned with the domestic use of wood energy. The wood energy plan of ADEME aims at encouraging the development of wood energy in three sectors: domestic, collective/tertiary, industrial. In that context, ADEME commissioned BIO Intelligence Service a life cycle assessment of collective and industrial heating in order to give objective environmental information and to analyse the strength and weakness of wood heating. Three scenarios were defined according to the origin of wood: firewood, granules and sawmill chips. The study also proposes a comparison to other heating systems: gas, fuel oil and electricity. The life cycle analysis applied to domestic heating consists in quantifying the environmental impacts of the whole linked steps: extraction of fuel, distribution, final use... Every system under study has been divided according to three main stages: - Extraction of raw materials; - Transport of fuels until the place of storage or distribution; - Use (combustion or upstream production of energy in the case of electricity). The environmental impacts are estimated with the following indicators: - Non renewable primary energy balance sheet; - Global warming potential; - Air acidification potential; - Eutrophication potential; - Emissions of toxic metals in air and in soils. The results show that wood heating have the best energy and global warming balance sheets. For air acidification, the combustion stage is pre-dominant regardless of the energy resource. This is mainly due to nitrogen and sulphur oxides airborne emissions. For wood heating, preparation requires fuel consumption which also contributes significantly to nitrogen oxides emissions. The comparison with conventional energy shows that the wood scenarios are well positioned in relation to fuel and electricity for this indicator. Gas appears to be the best heating option for this indicator. The contribution eutrophication is also due to nitrogen oxides airborne

  8. Study on the optimization of the pellet production and on the development of a forest-wood-pellet chain

    OpenAIRE

    Sgarbossa, Andrea

    2015-01-01

    The biomass and biofuels markets have increased substantially in the last two decades, mainly driven by the national and European policy targets on green energy. The same positive trend is registered in particular for wood pellet markets. In comparison with other wooden biofuels (firewood or wood-chips) pellets have a number of positive aspects such as: - regular and optimized shape; - wide range of energetic applications (to produce thermal energy, syngas, electricity); - high so...

  9. Small scale wood combustion in Germany. Recent research and trends

    Energy Technology Data Exchange (ETDEWEB)

    Maier, H.; Unterberger, S.; Hein, K.R.G. [Institute of Process Engineering and Power Plant Technology, University of Stuttgart (Germany)

    1998-12-31

    To reduce Europe`s greenhouse gas emission CO{sub 2} it is a challenging task utilising biomass fuels as there are wood or wood residues from the forest industry. The utilisation can be done either in commercially operated medium (> 50 kWth) or full scale (> 1 MWth) decentralised heat and power stations or in small scale (< 50 kWth) domestic heating systems. In small scale heating systems untreated wood logs, wood briquette or wood pellets and in few cases wood chips are used. The present market in Germany is focused on the use of wood logs. Presently, the use of wood pellets in small scale automatically operated boilers < 15 kW especially for low energy houses is discussed more and more. Since 1980 the installation of new wood fired small scale domestic heating systems reached a significant size due to the interest of the customers to have a alternative inhouse heating system and to increase the living comfort. In 1994 the amount of sold small scale heaters in Germany were in total about 133.258 units. The thermal power of in 1994 sold units is estimated of about 1350 MW which is a significant size in total with regard to domestic heating purposes. Since few years there is a clear market trend in Germany towards the installation of open fire stoves. Due to this trend in Germany and the design characteristic of open fire stoves using huge glass doors of glass windows it is very difficult to achieve a further reduction of emissions like CO and unburned volatile hydrocarbons (VOC). In the text the requirements for modern small scale wood fired stoves in Germany as well as the actual stage and trend of research and development (R and D) are discussed 4 refs.

  10. Chemi-thermomechanical pulping of para rubber waste wood

    Energy Technology Data Exchange (ETDEWEB)

    Kubo, T.; Hosokawa, J.; Kobayashi, T.; Kobayashi, Y.

    1981-01-01

    The addition of NaOH to Na/sub 2/SO/sub 3/-treated waste wood chips (Hevea brasiliensis) increased long fiber fraction, Klason lignin content and bulk density, improved breaking length and tear factor, and decreased energy consumption in refining and brightness of resulting chemithermomechanical pulp. Lowering in brightness by alkali treatment was recovered by H/sub 2/O/sub 2/ bleaching, and bleaching with 8% H/sub 2/O/sub 2/ on pulp gave pulp with 61.3% brightness.

  11. Wood would burn

    International Nuclear Information System (INIS)

    Swithenbank, Jim; Chen, Qun; Zhang, Xiaohui; Sharifi, Vida; Pourkashanian, Mohamed

    2011-01-01

    Absract: In view of the world-wide problem of energy sustainability and greenhouse gas production (carbon dioxide), it is timely to review the issues involved in generating heat and power from all fuels and especially new (to the UK) solid fuels, including high moisture fuels such as wood, SRF, oil shale, tar sands and brown coal, which will become major international fuels as oil and gas become depleted. The combustion properties of some of these materials are significantly different from traditional coal, oil and gas fuels, however the technology proposed herein is also applicable to these conventional fuels. This paper presents some innovative combustion system options and the associated technical factors that must be considered for their implementation. For clarity of understanding, the novel concepts will be largely presented in terms of a currently developing solid fuel market; biomass wood chips. One of the most important characteristics of many solid fuels to be used in the future (including oil shale and brown coal) is their high moisture content of up to 60%. This could be removed by utilising low grade waste heat that is widely available in industry to dry the fuel and thus reduce transport costs. Burning such dried wood for power generation also increases the energy available from combustion and thus acts as a thermal transformer by upgrading the low grade heat to heat available at combustion temperatures. The alternative approach presented here is to recover the latent heat by condensing the extrinsic moisture and the water formed during combustion. For atmospheric combustion, the temperature of the condensed combustion products is below the dew point at about 55-65 o C and is only suitable for recovery in an efficient district heating system. However, in order to generate power from the latent heat, the condensation temperature must be increased to the level where the heat can be used in the thermodynamic power cycle. This can be achieved by

  12. The operational efficiency of waterway transport of forest chips on Finland's Lake Saimaa

    Energy Technology Data Exchange (ETDEWEB)

    Karttunen, K.; Ranta, T. [Lappeenranta Univ. of Technology, LUT Savo Sustainable Technologies, Mikkeli (Finland); Vaatainen, K.; Asikainen, A. [The Finnish Forest Research Inst., Joensuu (Finland)], E-mail: kalle.karttunen@lut.fi

    2012-11-01

    New and cost-efficient methods for use in supply chains for energy wood should be found, to reach the targets of the renewable energy utilisation set by the European Union. The long-distance waterway transportation of forest fuels should be thoroughly investigated, especially in areas where the transport distance is long and waterways could provide a feasible method of conveying forest fuel. In comparison to transport of forest chips by truck, barge-based waterway transport shows a competitive advantage due to the larger loads and higher bulk density of chips it allows. The cost-efficiency of waterway transportation operations related to forest chips in Finland's Lake Saimaa region was studied using practical demonstrations and discrete-event simulation. The varying demand for fuel wood in three separate bio-power plants on the Saimaa lakeside (near the cities of Varkaus, Mikkeli, and Savonlinna) was addressed in several barge transportation scenarios. Finally, the economy of barge transportation was compared to the economy of truck transportation as a function of transportation distance and in terms of the annual performance of the transportation methods examined. The waterway supply chain of forest chips was cost-competitive to road transport by truck after 100-150 km. According to the simulation study, the most economical waterway transport options were based on fixed barge system and shift-independent harbor logistics where loading and unloading of barges were carried-out with a wheeled loader and a belt conveyor. Total supply chain costs including the best waterway logistics from road side storage to power plant ranged from 10.75 euros to 11.64 euros/MWh in distances of 100-150 km by waterways. The energy-density of forest chips in the barge load was found to be, on average, 25% higher than that in truck hauling, because of the better compaction of chips. Waterway transport is a viable option for long-distance transportation of forest chips in Eastern

  13. Transcript patterns of Phanerochaete chrysosporium genes in organopollutant contaminated soils and in wood

    Science.gov (United States)

    Amber. Vanden Wymelenberg; Bernard. Janse; Jill. Gaskell; Diane. Dietrich; Marcelo. Vallim; Dan. Cullen

    1998-01-01

    We describe here recent methods for quantitative assessment of specific P. chrysosporium mRNAs in organopollutant contaminated soils and in Aspen wood chips. Magnetic capture techniques were used to rapidly purify poly(A)-RNA, and quantitative RT-PCR protocols were developed for all known lignin peroxidase (lip) and cellobiohydrolase (cbh1) genes. The methodology is...

  14. Further development of a mixed-dryer for wood biomass; Sekoituskuivurin jatkokehitys

    Energy Technology Data Exchange (ETDEWEB)

    Heinonen, O. [Imatran Voima Oy, Vantaa (Finland). Research and Development; Parvio, E. [IVO International Oy, Vantaa (Finland)

    1995-12-31

    Imatran Voima Oy and IVO International Ltd are developing a new, advanced drying method for high moisture content fuels such as peat, biomass, and brown coal. The drying technology is based on using the heat of the fluidized bed directly for drying. The drying takes place at steam atmosphere, which makes it possible to recover the latent heat of evaporation back to process at high temperature level. This improves the thermal efficiency of the plant considerably. The technology is called bed mixing dryer. The pilot plant of the bed mixing dryer was built to IVO`s Kuusamo peat and wood fired power plant that was commissioned in the beginning of 1994. The Kuusamo district heating power plant has a fuel input of 27 MW that gives a power output of 6 MWe and district heat output of 17.5/21.2 MWth. As fuels are used peat, saw dust and wood wastes. The boiler is a bubbling fluidized bed boiler and the steam cycle is a conventional back pressure steam process. The unique feature in the plant is the new dryer that increases the overall thermal efficiency of the plant 10 to 15 units of percentage. In this project the operation and behaviour of the bed mixing dryer has been examined. Various components of the dryer were developed by the cold model tests carried out at IVO`s laboratory in Helsinki. Testing with the Kuusamo bed mixing dryer consisted of about 390 hours of drying tests with peat, bark and saw dust. The dryer operated well, and the drying was effective. The measured final moisture content varied from 7 to 19 % depending on the fuel particle size and the temperature level of the dryer

  15. Further development of a mixed-dryer for wood biomass; Sekoituskuivurin jatkokehitys

    Energy Technology Data Exchange (ETDEWEB)

    Heinonen, O. [Imatran Voima Oy, Vantaa (Finland). Research and Development; Parvio, E [IVO International Oy, Vantaa (Finland)

    1996-12-31

    Imatran Voima Oy and IVO International Ltd are developing a new, advanced drying method for high moisture content fuels such as peat, biomass, and brown coal. The drying technology is based on using the heat of the fluidized bed directly for drying. The drying takes place at steam atmosphere, which makes it possible to recover the latent heat of evaporation back to process at high temperature level. This improves the thermal efficiency of the plant considerably. The technology is called bed mixing dryer. The pilot plant of the bed mixing dryer was built to IVO`s Kuusamo peat and wood fired power plant that was commissioned in the beginning of 1994. The Kuusamo district heating power plant has a fuel input of 27 MW that gives a power output of 6 MWe and district heat output of 17.5/21.2 MWth. As fuels are used peat, saw dust and wood wastes. The boiler is a bubbling fluidized bed boiler and the steam cycle is a conventional back pressure steam process. The unique feature in the plant is the new dryer that increases the overall thermal efficiency of the plant 10 to 15 units of percentage. In this project the operation and behaviour of the bed mixing dryer has been examined. Various components of the dryer were developed by the cold model tests carried out at IVO`s laboratory in Helsinki. Testing with the Kuusamo bed mixing dryer consisted of about 390 hours of drying tests with peat, bark and saw dust. The dryer operated well, and the drying was effective. The measured final moisture content varied from 7 to 19 % depending on the fuel particle size and the temperature level of the dryer

  16. Anatomy of a field trial: Wood-based biochar and compost influences a Pacific Northwest soil

    Science.gov (United States)

    Biochar land application research in elevated rainfall areas (980 millimeters of annual rainfall) of the U.S. Pacific Northwest is lacking. A proof-of-concept field study examined the effects of spruce-pine-fir wood chip biochar (slow pyrolysis; 450-500 degrees Celsius; 35 megagrams per hectare), d...

  17. Production of renewable energy from biomass and waste materials using fluidized bed technologies

    International Nuclear Information System (INIS)

    Rozainee, M.; Rashid, M.; Looi, S.

    2000-01-01

    Malaysian industries generate substantial amount of biomass and waste materials such as wastes from agricultural and wood based industries, sludge waste from waste-water treatment plants and solid waste from municipals. Incinerating these waste materials not only produces renewable energy, but also solving their disposal problems. Fluidized bed combustors are widely used for incinerating these biomass materials. The significant advantages of fluidized bed incineration include simple design, efficient, and ability to reduce air pollution emissions. This paper discusses the opportunities and challenges of producing the green energy from biomass materials using the fluidized bed technologies. (Author)

  18. Rehabilitating agricultural streams in Australia with wood: a review.

    Science.gov (United States)

    Lester, Rebecca E; Boulton, Andrew J

    2008-08-01

    Worldwide, the ecological condition of streams and rivers has been impaired by agricultural practices such as broadscale modification of catchments, high nutrient and sediment inputs, loss of riparian vegetation, and altered hydrology. Typical responses include channel incision, excessive sedimentation, declining water quality, and loss of in-stream habitat complexity and biodiversity. We review these impacts, focusing on the potential benefits and limitations of wood reintroduction as a transitional rehabilitation technique in these agricultural landscapes using Australian examples. In streams, wood plays key roles in shaping velocity and sedimentation profiles, forming pools, and strengthening banks. In the simplified channels typical of many agricultural streams, wood provides habitat for fauna, substrate for biofilms, and refuge from predators and flow extremes, and enhances in-stream diversity of fish and macroinvertebrates.Most previous restoration studies involving wood reintroduction have been in forested landscapes, but some results might be extrapolated to agricultural streams. In these studies, wood enhanced diversity of fish and macroinvertebrates, increased storage of organic material and sediment, and improved bed and bank stability. Failure to meet restoration objectives appeared most likely where channel incision was severe and in highly degraded environments. Methods for wood reintroduction have logistical advantages over many other restoration techniques, being relatively low cost and low maintenance. Wood reintroduction is a viable transitional restoration technique for agricultural landscapes likely to rapidly improve stream condition if sources of colonists are viable and water quality is suitable.

  19. [Wood manufacture and dioxins: a case prospective study on maintenance of boilers powered by wood chips and shavings].

    Science.gov (United States)

    Vitelli, Marco; Paciaccioni, Daniele

    2014-01-01

    to verify if a carpenter using wood scraps, treated or not, to operate the heating system may involve an exposure to dioxins in a given target of workers. the research was structured on literature sources analysis, study on field of the most relevant exposure, occurs through sampling. The results were recorded and plotted, and compared with the data available in literature. the study has involved maintenance workers of the heating system by means of wood refuse incineration. These workers were informed of the methods and aims of the sample. the results confirm a potential exposure to ash containing dioxins, presumably also in other similar situations, in this case not even evaluated by the employer. the average exposure to the light ash during the maintenance operations of the plant dust abatement in emissive phase is about 5 mg/m(3), with a consequent exposure to dioxins inferred, at about 20 pg. operators are exposed to dioxins: this implies that in some operations it is crucial to review the risk assessment and consequently the measures on prevention and health protection to activate.

  20. Nitrogen immobilization in plant growth substrates: clean chip residual, pine bark and peat moss

    Science.gov (United States)

    A study was undertaken to determine the extent of nitrogen (N) immobilization and microbial respiration in a high wood-fiber content substrate (clean chip residual (CCR)). Control treatments of pine bark (PB) and peat moss (PM) were compared to two screen sizes (0.95 cm and 0.48 cm) of CCR for micro...

  1. Polymerization of impregnated monomer in wood by microwave irradiation

    International Nuclear Information System (INIS)

    Kawase, Kaoru; Hayakawa, Kiyoshi

    1976-01-01

    The manufacturing of a wood-plastic combination (WPC) by irradiation of microwave (2,450 and 915 +- 50 MHz) or gamma-ray was carried out. After the impregnation of dry woods (Hinoki: Chamaecyparis obtusa Endl., Buna: Acer mono Maxim., and Kaede: Fagus crenata Blume) with the mixture of the vinyl monomers and chemical reagents, the monomer in wood was polymerized by irradiation. In case of polymerization with microwave (2,450 MHz) the effect of oxygen was not recognized, but in the case of gamma-ray the rate of polymerization remarkably decreased in the presence of oxygen. The polymerization of various monomers was carried out also in the air, and the conversions of styrene, methyl-, ethyl-, n-propyl-, and n-butyl-methacrylate were 51.8 -- 89.1%, but that of vinyl acetate was lower (4.3 -- 8.2%). The conversion of monomers with irradiation of 915 MHz microwave was very low (2.6 -- 33.5%). The conversion of monomers increased when toluylene diisocyanate was added in the monomers. The percentage of extraction with hot benzene of WPC (chip) decreased by the addition of toluylene diisocyanate. It was concluded from C.H.N. analyses that the reaction took place among the wood, toluylene diisocyanate and methyl methacrylate. (auth.)

  2. A new bed-exiting alarm system for welfare facility residents.

    Science.gov (United States)

    Ogawa, Hidekuni; Yonezawa, Yoshiharu; Maki, Hiromichi; Caldwell, W

    2009-01-01

    A newly developed alarm system detects welfare facility residents leaving their beds, and does not respond to the care staff, who wear shoes or slippers. It employs a stainless steel tape electrode, several linear integrated circuits and a low-power 8-bit single chip microcomputer. The electrode, which is used as a bed-exiting detection sensor, is attached to the floor mat to record changes in the always-present AC (alternating current) voltage induced on the patient's body by electrostatic coupling from the standard 100 volt, 60 Hz AC utility power wiring in the room walls and ceiling. The resident's body movements, before trying to get out of bed and after leaving the bed, are detected by the microcomputer from changes in the induced AC voltage. The microcomputer alerts the care staff station, via a power line communication system or PHS (personal handy phone System).

  3. Particle Distribution in a Fixed Bed Down Draft Wood Gasifier

    DEFF Research Database (Denmark)

    Hindsgaul, Claus

    2005-01-01

    Char particle samples were collected from six distances above the grate in a fixed bed of a down draft biomass gasifier. Each sample was separated into twelve size fractions by screening through standard sieves in order to determine the local particle size distribution. The ash contents of each...

  4. LAND TREATMENT AND THE TOXICITY RESPONSE OF SOIL CONTAMINATED WITH WOOD PRESERVING WASTE

    Science.gov (United States)

    Soils contaminated with wood preserving wastes, including pentachlo-rophenol (PCP) and creosote, are treated at field-scale in an engineered prepared-bed system consisting of two one-acre land treatment units (LTUs). The concentration of selected indicator compounds of treatment ...

  5. Characterization of Cypress Wood for Kraft Pulp Production

    Directory of Open Access Journals (Sweden)

    António J. A. Santos

    2014-06-01

    Full Text Available Wood samples of Cupressus arizonica, C. lusitanica, and C. sempervirens were evaluated for chemical, anatomical, and pulp characteristics as raw material for pulp production. Two 17-year-old trees per species were harvested, and wood samples were taken at a height of 2 m. Wood chips from Pinus pinaster (Portugal and P. sylvestris (Finland were used as references. C. arizonica differed from C. lusitanica and C. sempervirens with significantly lower (p < 0.05 tracheid diameter and wall thickness in the earlywood. The total extractives contents were 3.9%, 3.3%, and 2.5% for C. lusitanica, C. sempervirens, and C. arizonica, respectively, lower than the 5.1% for P. pinaster and 4.5% for P. sylvestris. Klason lignin content ranged from 33.0 to 35.6%, higher than the 28.0 to 28.7% for the pinewoods. The kraft pulp yields for C. arizonica, C. lusitanica, and C. sempervirens were 37.7%, 36.7%, and 38.7%, respectively, with kappa numbers of 32.0, 31.6, and 28.7, respectively; the yield values were 40.8% and 42.8%, with kappa numbers of 23.4 and 21.0, for P. pinaster and P. sylvestris, respectively. The cypress species are clearly different from pine in relation to wood pulping behavior. Among the cypress, C. sempervirens provided the best pulping results.

  6. Ash related bed agglomeration during fluidized bed combustion, further development of the classification method based on CCSEM; CCSEM-luokitusmenetelmaen jatkokehittaeminen tuhkan aiheuttaman agglomeroitumisen tutkimisessa leiju- ja kiertopetipoltossa

    Energy Technology Data Exchange (ETDEWEB)

    Laitinen, R; Patrikainen, T; Heikkinen, R; Tiainen, M; Virtanen, M [Oulu Univ. (Finland). Inst. of Chemistry

    1997-10-01

    The scope of this project is to use the information and experience gained from the development of classification method to predict ash related problems like bed agglomeration during fluidised combustion. If boilers have to be shut down due to slagging or agglomeration of the bed material may cause significant economic losses for the entire energy production chain. Mineral classification methods based on the scanning electron microscopy are commonly used for coal ash investigation. In this work different biomass, peat, and peat-wood ash, fluidised-bed materials, and bed agglomerates were analysed with SEM-EDS combined with automatic image analysis software. The properties of ash particles are different depending on the fuel type. If biomass like wood or bark are added to peat the resulting ash has different properties. Due to the low mineral content in the original peat and to the fact that the majority of inorganic material is bound to the organic matrix, the classification has turned out to be less informative than was hoped. However, good results are obtained the by use of quasiternary diagrams. With these diagrams the distribution of particle composition is easily illustrated and thus meaningful prediction can be made of the slagging and agglomerating properties of ash. The content of ten different elements are determined for each particle by SEM-EDS combined with Link AIA software. The composition of the diagram corners can be varied Freely within these ten elements. (orig.)

  7. CFD modeling and experience of waste-to-energy plant burning waste wood

    DEFF Research Database (Denmark)

    Rajh, B.; Yin, Chungen; Samec, N.

    2013-01-01

    Computational Fluid Dynamics (CFD) is being increasingly used in industry for in-depth understanding of the fundamental mixing, combustion, heat transfer and pollutant formation in combustion processes and for design and optimization of Waste-to-Energy (WtE) plants. In this paper, CFD modeling...... the conversion of the waste wood in the fuel bed on the grate, which provides the appropriate inlet boundary condition for the freeboard 3D CFD simulation. The CFD analysis reveals the detailed mixing and combustion characteristics in the waste wood-fired furnace, pinpointing how to improve the design...

  8. Optimization of food waste hydrolysis in leach bed coupled with methanogenic reactor: effect of pH and bulking agent.

    Science.gov (United States)

    Xu, Su Yun; Lam, Hoi Pui; Karthikeyan, O Parthiba; Wong, Jonathan W C

    2011-02-01

    The effects of pH and bulking agents on hydrolysis/acidogenesis of food waste were studied using leach bed reactor (LBR) coupled with methanogenic up-flow anaerobic sludge blanket (UASB) reactor. The hydrolysis rate under regulated pH (6.0) was studied and compared with unregulated one during initial experiment. Then, the efficacies of five different bulking agents, i.e. plastic full particles, plastic hollow sphere, bottom ash, wood chip and saw dust were experimented under the regulated pH condition. Leachate recirculation with 50% water replacement was practiced throughout the experiment. Results proved that the daily leachate recirculation with pH control (6.0) accelerated the hydrolysis rate (59% higher volatile fatty acids) and methane production (up to 88%) compared to that of control without pH control. Furthermore, bottom ash improved the reactor alkalinity, which internally buffered the system that improved the methane production rate (0.182 l CH(4)/g VS(added)) than other bulking agents. Copyright © 2010 Elsevier Ltd. All rights reserved.

  9. 1H Nuclear Magnetic Resonance of Lodgepole Pine Wood Chips Affected by the Mountain Pine Beetle

    Directory of Open Access Journals (Sweden)

    Hartwig Peemoeller

    2010-12-01

    Full Text Available In this study, wood-water interactions of mountain pine beetle affected lodgepole pine were found to vary with time since death. Based on an analysis of magnetization components and spin-spin relaxation times from 1H NMR, it was determined that the mountain pine beetle attack does not affect the crystalline structure of the wood. Both the amorphous structure and the water components vary with time since death, which could be due to the fungi present after a mountain pine beetle attack, as well as the fact that wood from the grey-stage of attack cycles seasonally through adsorption and desorption in the stand.

  10. ¹H Nuclear Magnetic Resonance of Lodgepole Pine Wood Chips Affected by the Mountain Pine Beetle.

    Science.gov (United States)

    Todoruk, Tara M; Hartley, Ian D; Teymoori, Roshanak; Liang, Jianzhen; Peemoeller, Hartwig

    2010-12-31

    In this study, wood-water interactions of mountain pine beetle affected lodgepole pine were found to vary with time since death. Based on an analysis of magnetization components and spin-spin relaxation times from 1H NMR, it was determined that the mountain pine beetle attack does not affect the crystalline structure of the wood. Both the amorphous structure and the water components vary with time since death, which could be due to the fungi present after a mountain pine beetle attack, as well as the fact that wood from the grey-stage of attack cycles seasonally through adsorption and desorption in the stand.

  11. Harvesting energy wood in connection to young stand treatment; Energiapuun korjuu taimikon harvennuksen yhteydessae

    Energy Technology Data Exchange (ETDEWEB)

    Haemaelaeinen, J; Lilleberg, R; Poikela, A; Rieppo, K [Metsaeteho Oy, Helsinki (Finland)

    1997-12-01

    In the study felling-bunching and the Chipset chipharvester was tried in late thinning of a young stand. Also the impact of energy wood recovery in the young stand stage on the profitability of first thinning was monitored. On the study site the amount of trees to be cut was 5 300 - 22 000 trees/ha, mean height 2,7 - 5,0 m and the total biomass amounted to 26 - 75 m{sup 3}/ha. The felling-bunching was made with a chain-saw equipped with felling handles. The work consisted of opening of the strip roads, of thinning the stand between strip roads and of bunching the trees for the chip-harvester. The effective time expenditure of felling-bunching was on the different sites 8,5 - 27 in/ha or 0,24 - 0,64 h/m{sup 3}. The calculated costs of the work were 900 - 2 800 FIM/ha or 26 - 67 FIM/m{sup 3}. The density and volume of the trees strongly influenced work productivity. The Chipset chipping productivity was 5,7 - 8,7 m{sup 3} per gross effective hour. The chipping costs, when hauling distance was 250 meters, were 44 - 81 FIM/m{sup 3} or 21 - 43 FIM/MVVh. The total costs of energy wood procurement at the plant were 112 - 144 FIM/m{sup 3} or 56 - 73 FIM/MWh. The opening of strip roads during young stand treatment decreases net volume later in the first thinning. According to calculations made for the example sites the net volume decreased by approx. 9 m{sup 3}/ha. The first thinning costs thus increased by 4 FIM/m{sup 3} or ca 5 %. In the extension project the technical, economical and productional preconditions for combining young stand treatment, energy wood harvesting and first thinning will be monitored

  12. Emissions from laboratory combustor tests of manufactured wood products

    Energy Technology Data Exchange (ETDEWEB)

    Wilkening, R.; Evans, M.; Ragland, K. [Univ. of Wisconsin, Madison, WI (United States); Baker, A. [USDA Forest Products Lab., Madison, WI (United States)

    1993-12-31

    Manufactured wood products contain wood, wood fiber, and materials added during manufacture of the product. Manufacturing residues and the used products are burned in a furnace or boiler instead of landfilling. Emissions from combustion of these products contain additional compounds from the combustion of non-wood material which have not been adequately characterized to specify the best combustion conditions, emissions control equipment, and disposal procedures. Total hydrocarbons, formaldehyde, higher aldehydes and carbon monoxide emissions from aspen flakeboard and aspen cubes were measured in a 76 mm i.d. by 1.5 m long fixed bed combustor as a function of excess oxygen, and temperature. Emissions of hydrocarbons, aldehydes and CO from flakeboard and from clean aspen were very sensitive to average combustor temperature and excess oxygen. Hydrocarbon and aldehyde emissions below 10 ppM were achieved with 5% excess oxygen and 1,200{degrees}C average temperature for aspen flakeboard and 1,100{degrees}C for clean aspen at a 0.9 s residence time. When the average temperature decreased below these levels, the emissions increased rapidly. For example, at 950{degrees}C and 5% excess oxygen the formaldehyde emissions were over 1,000 ppM. These laboratory tests reinforce the need to carefully control the temperature and excess oxygen in full-scale wood combustors.

  13. Cost calculation model concerning small-scale production of chips and split firewood

    International Nuclear Information System (INIS)

    Ryynaenen, S.; Naett, H.; Valkonen, J.

    1995-01-01

    The TTS-Institute's Forestry Department has developed a computer-based cost calculation model for the production of wood chips and split firewood. This development work was carried out in conjunction with the nation-wide BIOENERGY -research programme. The said calculation model eases and speeds up the calculation of unit costs and resource needs in harvesting systems for wood chips and split firewood. The model also enables the user to find out how changes in the productivity and costs bases of different harvesting chains influences the unit costs of the system as a whole. The undertaking was composed of the following parts: clarification and modification of productivity bases for application in the model as mathematical models, clarification of machine and device costs bases, designing of the structure and functions of the calculation model, construction and testing of the model's 0-version, model calculations concerning typical chains, review of calculation bases, and charting of development needs focusing on the model. The calculation model was developed to serve research needs, but with further development it could be useful as a tool in forestry and agricultural extension work, related schools and colleges, and in the hands of firewood producers. (author)

  14. Identification and Characterization of Trichoderma Species Damaging Shiitake Mushroom Bed-Logs Infested by Camptomyia Pest.

    Science.gov (United States)

    Kim, Jun Young; Kwon, Hyuk Woo; Yun, Yeo Hong; Kim, Seong Hwan

    2016-05-28

    The shiitake mushroom industry has suffered from Camptomyia (gall midges) pest, which feeds on the mycelium of shiitake mushroom during its cultivation. It has been postulated that fungal damage of shiitake bed-logs is associated with infestation by the insect pest, but this is not well understood. To understand the fungal damage associated with Camptomyia pest, various Trichoderma species were isolated, identified, and characterized. In addition to two previously known Trichoderma species, T. citrinoviride and T. deliquescens, two other Trichoderma species, T. harzianum and T. atroviride, were newly identified from the pestinfested bed-log samples obtained at three mushroom farms in Cheonan, Korea. Among these four species, T. harzianum was the most evident. The results of a chromogenic media-based assay for extracellular enzymes showed that these four species have the ability to produce amylase, carboxyl-methyl cellulase, avicelase, pectinase, and β-glucosidase, thus indicating that they can degrade wood components. A dual culture assay on PDA indicated that T. harzianum, T. atroviride, and T. citrinoviride were antagonistic against the mycelial growth of a shiitake strain (Lentinula edodes). Inoculation tests on shiitake bed-logs revealed that all four species were able to damage the wood of bed-logs. Our results provide evidence that the four green mold species are the causal agents involved in fungal damage of shiitake bed-logs infested by Camptomyia pest.

  15. URBAN WOOD/COAL CO-FIRING IN THE BELLEFIELD BOILERPLANT

    International Nuclear Information System (INIS)

    James T. Cobb, Jr.; Gene E. Geiger; William W. Elder III; William P. Barry; Jun Wang; Hongming Li

    2001-01-01

    During the third quarter, important preparatory work was continued so that the experimental activities can begin early in the fourth quarter. Authorization was awaited in response to the letter that was submitted to the Allegheny County Health Department (ACHD) seeking an R and D variance for the air permit at the Bellefield Boiler Plant (BBP). Verbal authorizations were received from the Pennsylvania Department of Environmental Protection (PADEP) for R and D variances for solid waste permits at the J. A. Rutter Company (JARC), and Emery Tree Service (ETS). Construction wood was acquired from Thompson Properties and Seven D Corporation. Forty tons of pallet and construction wood were ground to produce BioGrind Wood Chips at JARC and delivered to Mon Valley Transportation Company (MVTC). Five tons of construction wood were milled at ETS and half of the product delivered to MVTC. Discussions were held with BBP and Energy Systems Associates (ESA) about the test program. Material and energy balances on Boiler No.1 and a plan for data collection were prepared. Presentations describing the University of Pittsburgh Wood/Coal Co-Firing Program were provided to the Pittsburgh Chapter of the Pennsylvania Society of Professional Engineers, and the Upgraded Coal Interest Group and the Biomass Interest Group (BIG) of the Electric Power Research Institute (EPRI). An article describing the program appeared in the Pittsburgh Post-Gazette. An application was submitted for authorization for a Pennsylvania Switchgrass Energy and Conservation Program

  16. Radon reduction in wood foundation system

    International Nuclear Information System (INIS)

    Clark, R.J.

    1990-01-01

    Radon, an issue of growing concern to the building industry. Silently, invisibly, it invades existing structures as it will future foundation structures. This paper addresses the nature and causes of radon, and cost-effective prevention and retrofit techniques used for wood foundation systems. Radon also can enter homes with foundations that use the under-floor as an air distribution system. These building practices will be shown; even materials used in construction may release radon, for example, this may be a problem in a house that has a solar heating system in which its heat is stored in large beds of stone. Stone is most often used in wood foundation construction. The common radon entry points will be looked at, and the latest prevention techniques will be illustrated, such as natural and forced ventilation, sealing major radon sources and entry routes, and sub-slab and sump crock ventilations

  17. Elemental and organic carbon in flue gas particles of various wood combustion systems

    Energy Technology Data Exchange (ETDEWEB)

    Gaegauf, C.; Schmid, M.; Guentert, P.

    2005-12-15

    The airborne particulate matter (PM) in the environment is of ever increasing concern to authorities and the public. The major fractions of particles in wood combustion processes are in the size less than 1 micron, typically in the range of 30 to 300 nm. Of specific interest is the content of the elemental carbon (EC) and organic carbon (OC) in the particles since these substances are known for its particular potential as carcinogens. Various wood combustion systems have been analysed (wood chip boiler, pellet boiler, wood log boiler, wood stove and open fire). The sampling of the particles was done by mean of a multi-stage particle sizing sampler cascade impactor. The impactor classifies the particles collected according to their size. The 7 stages classify the particles between 0.4 and 9 microns aerodynamic diameter. The analytical method for determining the content of EC and OC in the particles is based on coulometry. The coulometer measures the conductivity of CO{sub 2} released by oxidation of EC in the samples at 650 {sup o}C. The OC content is determined by pyrolysis of the particle samples in helium atmosphere.

  18. Optimum diameter of a circulating fluidised bed combustor with negative wall heat flux

    CSIR Research Space (South Africa)

    Baloyi, J

    2015-07-01

    Full Text Available on irreversibilities in a 7 m circulating fluidised bed combustor with a negative wall heat flux, firing a mixture of air and solid pitch pine wood, was investigated. An analytical expression was derived that predicts the entropy generation rate, thereby...

  19. Wood Combustion Behaviour in a Fixed Bed Combustor

    Science.gov (United States)

    Tokit, Ernie Mat; Aziz, Azhar Abdul; Ghazali, Normah Mohd

    2010-06-01

    Waste wood is used as feedstock for Universiti Teknologi Malaysia's newly-developed two-stage incinerator system. The research goals are to optimize the operation of the thermal system to the primary chamber, to improve its combustion efficiency and to minimize its pollutants formation. The combustion process is evaluated with the variation of fuel's moisture content. For optimum operating condition, where the gasification efficiency is 95.53%, the moisture content of the fuel is best set at 17%; giving outlet operating temperature of 550°C and exhaust gas concentrations with 1213 ppm of CO, 6% of CO2 and 14% of O2 respectively. In line to the experimental work, a computational fluid dynamics software, Fluent is used to simulate the performance of the primary chamber. Here the predicted optimum gasification efficiency stands at 95.49% with CO, CO2 and O2 concentrations as 1301 ppm, 6.5% and 13.5% respectively.

  20. Fixed-bed column adsorption of methyl blue using carbon derived ...

    African Journals Online (AJOL)

    Axle Wood Carbon (AWC) was used to study the removal of Methyl Blue (MB) from its aqueous solution in a fixed-bed column adsorption system. The adsorbent (AWC) was characterized using SEM and pHPZC. SEM revealed the surface morphology and from the pHPZC determination, it was found that at pH of 8.21 the ...

  1. Evaluation of greenhouse gas emission risks from storage of wood residue

    International Nuclear Information System (INIS)

    Wihersaari, Margareta

    2005-01-01

    The use of renewable energy sources instead of fossil fuels is one of the most important means of limiting greenhouse gas emissions in the near future. In Finland, wood energy is considered to be a very important potential energy source in this sense. There might, however, still be some elements of uncertainty when evaluating biofuel production chains. By combining data from a stack of composting biodegradable materials and forest residue storage research there was an indication that rather great amounts of greenhouse gases maybe released during storage of wood chip, especially if there is rapid decomposition. Unfortunately, there have not been many evaluations of greenhouse gas emissions of biomass handling and storage heaps. The greenhouse gas emissions are probably methane, when the temperature in the fuel stack is above the ambient temperature, and nitrous oxide, when the temperature is falling and the decaying process is slowing down. Nowadays it is still rather unusual to store logging residue as chips, because the production is small, but in Finland storage of bark and other by-products from the forest industry is a normal process. The evaluations made indicate that greenhouse gas emissions from storage can, in some cases, be much greater than emissions from the rest of the biofuel production and transportation chain

  2. Cyclic polyalcohols: fingerprints to identify the botanical origin of natural woods used in wine aging.

    Science.gov (United States)

    Alañón, M Elena; Díaz-Maroto, M Consuelo; Díaz-Maroto, Ignacio J; Vila-Lameiro, Pablo; Pérez-Coello, M Soledad

    2011-02-23

    Cyclic polyalcohol composition of 80 natural wood samples from different botanical species, with the majority of them used in the oenology industry for aging purposes, has been studied by gas chromatography-mass spectrometry (GC-MS) after its conversion into their trimethylsilyloxime derivatives. Each botanical species showed a different and specific cyclic polyalcohol profile. Oak wood samples were characterized by the richness in deoxyinositols, especially proto-quercitol. Meanwhile, other botanical species showed a very low content of cyclic polyalcohols. The qualitative and quantitative study of cyclic polyalcohols was a useful tool to characterize and differentiate woods of different botanical origin to guarantee the authenticity of chips used in the wine-aging process. Monosaccharide composition was also analyzed, showing some quantitative differences among species, but cyclic polyalcohols were the compounds that revealed the main differentiation power.

  3. URBAN WOOD/COAL CO-FIRING IN THE NIOSH BOILER PLANT

    Energy Technology Data Exchange (ETDEWEB)

    James T. Cobb Jr.

    2005-02-10

    gasification project at its site. Throughout much of this total project the Principal Investigator has counseled two small businesses in developing a waxed cardboard pellet business. A recent test burn of this biofuel appears successful and a purchase contract is anticipated soon. During the past two months a major tree-trimming firm has shown an active interest in entering the wood-chip fuel market in the Pittsburgh area and has contacted the NBP, among others, as potential customers. The NBP superintendent is currently in discussion with the facilities management of the Bruceton Research Center about resuming their interest in cofiring this renewable fuel to the stoker there.

  4. Preparation for full scale demonstration of an air staged gasifier plant. Technical project development; For combined heat and power production with wood chips; Forberedelse til fuldskala demonstration af trinopdelt forgasningsanlaeg. Teknisk projektudvikling. Delrapport

    Energy Technology Data Exchange (ETDEWEB)

    Houmann Jakobsen, H.

    2011-04-15

    The project has aimed to further develop the technology for staged biomass gasification and establish an organizational and financial model to ensure that the technology can be introduced on the market. This report describes the technique in an upcoming demonstration plant. A complete planning and design of a demonstration plant with a capacity of 300 kW electric power and 700 kW heat was prepared. That is four times more than the pilot plant at Graested District Heating (Castor plant) can produce. A full scale demonstration plant with bio-gasification technology for wood chips will be established and put into operation in 2012. (ln)

  5. NANOCOATING PROCESS FOR TEXTILES APPLICATIONS AND WOOD PROTECTION

    Directory of Open Access Journals (Sweden)

    NICULESCU Claudia

    2014-05-01

    Full Text Available This paper presents the research results obtained in ERA NET MANUCOAT project, coordinated by INCDTP in collaboration with the following partners: INCDMNR-IMNR, SC MGM STAR CONSTRUCT SRL –Romania and IRIS-Spain. The objective of the research was to develop and obtain textile and wood surfaces with self-cleaning, photo catalytic, antibacterial and antifungal properties. An innovative method of manufacturing nanoparticles by hydrothermal process in a single step without any further heat treatment and controlled stoichiometry, tested spray coating technology (sputtering were developed. Full characterization of nanostructured powders in terms of chemical, physical, structural, thermal and technological characteristics was performed. The most important features to be considered in the treatment of wood by sputtering in order to deposit thin layers of TiO2 NPs or TiO2/Ag as the humidity should be below 12% and the maximum roughness P150, depending on the species of wood. Future works envisage optimizing the existing sputtering systems for pilot stage, in order to make nanoparticles deposits on large areas of textile and wood. The results of the research are photocatalytic textiles for surgical gowns, operative fields, hospital bed sheets and curtains and drapes for public spaces.

  6. Fluidized bed combustion of low-grade coal and wastes: Research and development

    Energy Technology Data Exchange (ETDEWEB)

    Borodulya, V.A.; Dikalenko, V.I.; Palchonok, G.I.; Vinogradov, L.M. [Academy of Sciences of Belarus, Minsk (Belarus). A.V. Luikov Heat and Mass Transfer Inst.; Dobkin, S.M.; Telegin, E.M. [Special Design Office, Brest (Belarus)

    1994-12-31

    Experimental studies were carried out to investigate devolatilization of fuel as single spherical particles of wood, hydrolytic lignin, leather sewage sludge and Belarussian brown coals in a fluidized bed of sand. It is found that the devolatilization process depends on moisture and ash contents in fuel and on the external heat and mass transfer rate. The char combustion occurs largely in the intermediate region. Kinetic parameters of the devolatilization and char combustion are obtained. A low-capacity fluidized bed boiler suitable for combustion of coal and different wastes is described.

  7. Cytotoxic and genotoxic responses of human lung cells to combustion smoke particles of Miscanthus straw, softwood and beech wood chips

    Science.gov (United States)

    Arif, Ali Talib; Maschowski, Christoph; Garra, Patxi; Garcia-Käufer, Manuel; Petithory, Tatiana; Trouvé, Gwenaëlle; Dieterlen, Alain; Mersch-Sundermann, Volker; Khanaqa, Polla; Nazarenko, Irina; Gminski, Richard; Gieré, Reto

    2017-08-01

    Inhalation of particulate matter (PM) from residential biomass combustion is epidemiologically associated with cardiovascular and pulmonary diseases. This study investigates PM0.4-1 emissions from combustion of commercial Miscanthus straw (MS), softwood chips (SWC) and beech wood chips (BWC) in a domestic-scale boiler (40 kW). The PM0.4-1 emitted during combustion of the MS, SWC and BWC were characterized by ICP-MS/OES, XRD, SEM, TEM, and DLS. Cytotoxicity and genotoxicity in human alveolar epithelial A549 and human bronchial epithelial BEAS-2B cells were assessed by the WST-1 assay and the DNA-Alkaline Unwinding Assay (DAUA). PM0.4-1 uptake/translocation in cells was investigated with a new method developed using a confocal reflection microscope. SWC and BWC had a inherently higher residual water content than MS. The PM0.4-1 emitted during combustion of SWC and BWC exhibited higher levels of Polycyclic Aromatic Hydrocarbons (PAHs), a greater variety of mineral species and a higher heavy metal content than PM0.4-1 from MS combustion. Exposure to PM0.4-1 from combustion of SWC and BWC induced cytotoxic and genotoxic effects in human alveolar and bronchial cells, whereby the strongest effect was observed for BWC and was comparable to that caused by diesel PM (SRM 2 975), In contrast, PM0.4-1 from MS combustion did not induce cellular responses in the studied lung cells. A high PAH content in PM emissions seems to be a reliable chemical marker of both combustion efficiency and particle toxicity. Residual biomass water content strongly affects particulate emissions and their toxic potential. Therefore, to minimize the harmful effects of fine PM on health, improvement of combustion efficiency (aiming to reduce the presence of incomplete combustion products bound to PM) and application of fly ash capture technology, as well as use of novel biomass fuels like Miscanthus straw is recommended.

  8. Radioactivity of wood ash

    International Nuclear Information System (INIS)

    Rantavaara, A.; Moring, M.

    2000-01-01

    STUK (Finnish Radiation and Nuclear Safety Authority) has investigated natural and artificial radioactivity in wood ash and radiation exposure from radionuclides in ash since 1996. The aim was to consider both handling of ash and different ways of using ash. In all 87 ash samples were collected from 22 plants using entirely or partially wood for their energy production in 1996-1997. The sites studied represented mostly chemical forest industry, sawmills or district heat production. Most plants used fluidised bed combustion technique. Samples of both fly ash and bottom ash were studied. The activity concentrations of radionuclides in samples of, e.g., dried fly ash from fuel containing more than 80% wood were determined. The means ranged from 2000 to less than 50 Bq kg -1 , in decreasing order: 137 Cs, 40 K, 90 Sr, 210 Pb, 226 Ra, 232 Th, 134 Cs, 235 U. In bott radionuclide contents decreased in the same order as in fly ash, but were smaller, and 210 Pb was hardly detectable. The NH 4 Ac extractable fractions of activities for isotopes of alkaline elements (K, Cs) in bottom ash were lower than in fly ash, whereas solubility of heavier isotopes was low. Safety requirements defined by STUK in ST-guide 12.2 for handling of peat ash were fulfilled at each of the sites. Use of ash for land-filling and construction of streets was minimal during the sampling period. Increasing this type of ash use had often needed further investigations, as description of the use of additional materials that attenuate radiation. Fertilisation of forests with wood ash adds slightly to the external irradiation in forests, but will mostly decrease doses received through use of timber, berries, mushrooms and game meat. (orig.)

  9. Simulant - water experiments to characterize the debris bed formed in severe core melt accidents

    International Nuclear Information System (INIS)

    Mathai, Amala M.; Anandan, J.; Sharma, Anil Kumar; Murthy, S.S.; Malarvizhi, B.; Lydia, G.; Das, Sanjay Kumar; Nashine, B.K.; Selvaraj, P.

    2015-01-01

    Molten Fuel Coolant Interaction (WO) and debris bed configuration on the core catcher plate assumes importance in assessing the Post Accident Heat Removal (PARR) of a heat generating debris bed. The key factors affecting the coolability of the debris bed are the bed porosity, morphology of the fragmented particles, degree of spreading/heaping of the debris on the core catcher and the fraction of lump formed. Experiments are conducted to understand the fragmentation kinetics and subsequent debris bed formation of molten woods metal in water at interface temperatures near the spontaneous nucleation temperature of water. Morphology of the debris particles is investigated to understand the fragmentation mechanisms involved. The spreading behavior of the debris on the catcher plate and the particle size distribution are presented for 5 kg and 10 kg melt inventories. Porosity of the undisturbed bed on the catcher plate is evaluated using a LASER sensor technique. (author)

  10. Morphological characteristics of loblolly pine wood as related to specific gravity, growth rate and distance from pith

    Science.gov (United States)

    Charles W. McMillin

    1968-01-01

    Earlywood and latewood tracheid length and transverse cellular dimensions of wood removed from stems of loblolly pine (Pinus taeda L.) and factorially aegregated by specific gravity, rings from the pith, and growth rate were determined from sample chips. The independent relationships of each factor with fiber morphology are described.

  11. Odorous volatile organic compounds, Escherichia coli, and nutrient concentrations when kiln-dried pine chips and corn stover bedding are used in beef bedded manure packs

    Science.gov (United States)

    Pine (Pinus spp.) bedding has been shown to lower the concentration of odorous volatile organic compounds (VOCs) and pathogenic bacteria compared with corn (Zea mays L.) stover bedding, but availability and cost limit the use of pine bedding in cattle confinement facilities. The objectives of this s...

  12. CO{sub 2}-EQ emissions of forest chip production in Finland in 2020

    Energy Technology Data Exchange (ETDEWEB)

    Kariniemi, Arto; Kaerhae, Kalle (Metsaeteho Oy, Helsinki (Finland)), e-mail: arto.kariniemi@metsateho.fi

    2010-07-15

    The research carried out by Metsaeteho Oy calculated what would be the total fuel consumption and CO{sub 2}-eq emissions of forest chip production if the use of forest chips is 24 TWh in 2020 in Finland in accordance with the target set of Long-term Climate and Energy Strategy. CO{sub 2}-eq emissions were determined with Metsaeteho Oy's updated Emissions Calculation Model. If the production and consumption of forest chips in Finland are 24 TWh in 2020, then the total CO{sub 2}-eq emissions would be around 230,000 tonnes. The volume of diesel consumption was 73 million litres and petrol 1.7 million litres. Electric rail transportation and chipping at the mill site consumed 17 GWh of electricity. The supply chain with the lowest CO{sub 2}-eq emissions was logging residues comminuted at plant. Conversely, the highest CO{sub 2}-eq emissions came from stump wood when operating with terminal comminuting. Less than 3% of the energy content was consumed during the forest chip production. Energy input/output ratio in the total volume was 0.026 MWh/MWh which varied from 0.019 to 0.038 between the supply systems researched. Hence, forest chip production gave a net of some 97% of the energy content delivered at the plant

  13. Nitrogen Immobilization in Plant Growth Substrates: Clean Chip Residual, Pine Bark, and Peatmoss

    Directory of Open Access Journals (Sweden)

    Cheryl R. Boyer

    2012-01-01

    Full Text Available Rising costs of potting substrates have caused horticultural growers to search for alternative, lower-cost materials. Objectives of this study were to determine the extent of nitrogen immobilization and microbial respiration in a high wood-fiber content substrate, clean chip residual. Microbial activity and nitrogen availability of two screen sizes (0.95 cm and 0.48 cm of clean chip residual were compared to control treatments of pine bark and peatmoss in a 60-day incubation experiment. Four rates (0, 1, 2, or 3 mg of supplemental nitrogen were assessed. Peatmoss displayed little microbial respiration over the course of the study, regardless of nitrogen rate; followed by pine bark, 0.95 cm clean chip residual, and 0.48 cm clean chip residual. Respiration increased with increasing nitrogen. Total inorganic nitrogen (plant available nitrogen was greatest with peatmoss; inorganic nitrogen in other treatments were similar at the 0, 1, and 2 mg supplemental nitrogen rates, while an increase occurred with the highest rate (3 mg. Clean chip residual and pine bark were similar in available nitrogen compared to peatmoss. This study suggests that nitrogen immobilization in substrates composed of clean chip residual is similar to pine bark and can be treated with similar fertilizer amendments during nursery production.

  14. Slow sedimentary processes on-a-chip: experiments on porous flow effects on granular bed creep

    Science.gov (United States)

    Houssais, M.; Maldarelli, C.; Shattuck, M.; Morris, J. F.

    2017-12-01

    Steep soils dynamics is hard to catch. they exhibit very slow granular creep most of the time, and sometimes, mostly under or after rain, turn into a landslide, a very fast avalanche flow.The conditions of transition from soil creep to avalanching remains a lot non-understood, and Safe Factor law (empirical criteria, function of rain intensity and duration). On another side, in marine fast deposition environments, compaction drives vertical porous flow, which makes bed shear resistance change, and form over time bed size patterns (pipes, dishes) or mechanical heterogeneities.Capturing how the slow creep dynamics depends on the porous flow would allow for much more accurate landscape evolution modeling.We present here preliminary results of an experimental investigation of one the major triggering condition for soils destabilization: rain infiltration, and more generally porous flow through a tilted granular bed. In a quasi-2D microfluidics channel, a flat sediment bed made of spherical particles is prepared, in fully submerged condition. It is thereafter tilted (at slope under critical slope of avalanching) and simultaneously put under vertical weak porous flow (well under the critical flow of liquefaction regarding positive pressure gradients). The two control parameters are varied, and local particles concentration and motion are measured. Interestingly, although staying in the sub-critical creeping regime, we observe an acceleration of the bed deformation downward, as the porous flow and the bed slope are increased, until the criteria for avalanching is reached. Those results appear to present similitudes with the case of tilted dry sediment bed under controlled vibrations. Consequently it opens the discussion about a potential universal model of landslides triggering due to frequent seismological and rainstorm events.

  15. Wood fuel from early thinning and plantation cleaning. Summary of an international review

    International Nuclear Information System (INIS)

    Puttock, D.

    1998-01-01

    This paper summaries the results of an international of wood fuel from early thinning and plantation cleaning. The economic and biological benefits from early thinning have been well documented. However, removing forest biomass during early stages of stand development from sites which are low in one or more nutrients may contribute a loss of nutrients and organic matter. Depending on the pre-thinning density and the thinning intensity, the potential yield of wood fuel from early thinning may be as much as 79 dry tons per hectare. Thus, wood fuel from the thinnings could be an important source of revenue to forest owners and would contribute to domestic energy requirements. Motor-manual felling predominates in early thinning, mainly due to the lack of appropriate technology for thinning small trees. However, the productivity of motor-manual felling is greatly affected by the initial stand density and declines dramatically at densities greater than 10 000 stems per ha. Under these conditions, purpose-built wood fuel harvesters with small-tree harvesting capability offer the greatest potential for increasing felling productivity and reducing the cost of wood fuel. The cost of wood fuel from early thinnings varies widely between countries from USD 25.00 - 87.50 per dry ton depending on stand conditions, harvesting system, transport distance, domestic tax rates, and stumpage prices. At the low end of this range, wood fuel chips from early thinning are competitive with wood fuel produced from mill waste, the residues from clearfell operations, or from later thinnings

  16. Catalytic upgrading nitrogen-riched wood syngas to liquid hydrocarbon mixture over Fe-Pd/ZSM-5 catalyst

    Science.gov (United States)

    Qiangu Yan; Fei Yu; Zhiyong Cai; Jilei Zhang

    2012-01-01

    Biomass like wood chips, switchgrass and other plant residues are first converted to syngas through gasification process using air, oxygen or steam. A downdraft gasifier is performed for syngas production in Mississippi State. The syngas from the gasifier contains up to 49% (vol) N2. High-level nitrogen-containing (nitrogen can be up to 60%)...

  17. Heterogeneous studies in pulping of wood: Modelling mass transfer of alkali

    OpenAIRE

    Simão, João P. F.; Egas, Ana P. V.; Carvalho, M. Graça; Baptista, Cristina M. S. G.; Castro, José Almiro A. M.

    2008-01-01

    In this paper a heterogeneous lumped parameter model is proposed to describe the mass transfer of effective alkali during the kraft pulping of wood. This model, based on the spatial mean of the concentration profile of effective alkali along the chip thickness, enables the estimation of the effective diffusion coefficient that characterizes the internal resistance to mass transfer and the contribution of the external resistance to mass transfer which has often been neglected. http://www.sc...

  18. Instream wood loads in montane forest streams of the Colorado Front Range, USA

    Science.gov (United States)

    Jackson, Karen J.; Wohl, Ellen

    2015-04-01

    Although several studies examine instream wood loads and associated geomorphic effects in streams of subalpine forests in the U.S. Southern Rocky Mountains, little is known of instream wood loads in lower elevation, montane forests of the region. We compare instream wood loads and geomorphic effects between streams draining montane forest stands of differing age (old growth versus younger) and disturbance history (healthy versus infested by mountain pine beetles). We examined forest stand characteristics, instream wood load, channel geometry, pool volume, and sediment storage in 33 pool-riffle or plane-bed stream reaches with objectives of determining whether (i) instream wood and geomorphic effects differed significantly among old-growth, younger, healthy, and beetle-infested forest stands and (ii) wood loads correlated with valley and channel characteristics. Wood loads were standardized to drainage area, stream gradient, reach length, bankfull width, and floodplain area. Streams flowing through old-growth forests had significantly larger wood loads and logjam volumes (pairwise t-tests), as well as logjam frequencies (Kruskal-Wallis test), residual pool volume, and fine sediment storage around wood than streams flowing through younger forests. Wood loads in streams draining beetle-infested forest did not differ significantly from those in healthy forest stands, but best subset regression models indicated that elevation, stand age, and beetle infestation were the best predictors of wood loads in channels and on floodplains, suggesting that beetle infestation is affecting instream wood characteristics. Wood loads are larger than values from subalpine streams in the same region and jams are larger and more closely spaced. We interpret these differences to reflect greater wood piece mobility in subalpine zone streams. Stand age appears to exert the dominant influence on instream wood characteristics within pool-riffle streams in the study area rather than beetle

  19. Bedding material affects mechanical thresholds, heat thresholds and texture preference

    Science.gov (United States)

    Moehring, Francie; O’Hara, Crystal L.; Stucky, Cheryl L.

    2015-01-01

    It has long been known that the bedding type animals are housed on can affect breeding behavior and cage environment. Yet little is known about its effects on evoked behavior responses or non-reflexive behaviors. C57BL/6 mice were housed for two weeks on one of five bedding types: Aspen Sani Chips® (standard bedding for our institute), ALPHA-Dri®, Cellu-Dri™, Pure-o’Cel™ or TEK-Fresh. Mice housed on Aspen exhibited the lowest (most sensitive) mechanical thresholds while those on TEK-Fresh exhibited 3-fold higher thresholds. While bedding type had no effect on responses to punctate or dynamic light touch stimuli, TEK-Fresh housed animals exhibited greater responsiveness in a noxious needle assay, than those housed on the other bedding types. Heat sensitivity was also affected by bedding as animals housed on Aspen exhibited the shortest (most sensitive) latencies to withdrawal whereas those housed on TEK-Fresh had the longest (least sensitive) latencies to response. Slight differences between bedding types were also seen in a moderate cold temperature preference assay. A modified tactile conditioned place preference chamber assay revealed that animals preferred TEK-Fresh to Aspen bedding. Bedding type had no effect in a non-reflexive wheel running assay. In both acute (two day) and chronic (5 week) inflammation induced by injection of Complete Freund’s Adjuvant in the hindpaw, mechanical thresholds were reduced in all groups regardless of bedding type, but TEK-Fresh and Pure-o’Cel™ groups exhibited a greater dynamic range between controls and inflamed cohorts than Aspen housed mice. PMID:26456764

  20. Multivariate Correlation between Analysis Data on Dissolved Organic Material from Scots Pine (Pinus sylvestris Chips and their Autohydrolysis Pre-Treatment Conditions

    Directory of Open Access Journals (Sweden)

    Joni Lehto

    2013-11-01

    Full Text Available Various chemometric techniques were used to establish the relationship between the autohydrolysis conditions prior to pulping and the chemical compositions of the soluble organic materials removed from Scots pine (Pinus sylvestris wood chips. The aqueous chip pre-treatments (autohydrolysis were administered at 130 °C and 150 °C for 30, 60, 90, and 120 min, and the hydrolysates obtained were characterized in terms of total carbohydrates (various mono-, oligo-, and polysaccharides together with uronic acid side groups, volatile acids (acetic and formic acids, lignin, and furans (furfural and 5-(hydroxymethylfurfural. Based on the analytical data gathered, a relatively accurate model for pine chip autohydrolysis was developed.

  1. Theoretical and experimental studies on emissions from wood combustion

    Energy Technology Data Exchange (ETDEWEB)

    Skreiberg, Oeyvind

    1997-12-31

    This thesis discusses experiments on emissions from wood log combustion and single wood particle combustion, both caused by incomplete combustion and emissions of nitric and nitrous oxide, together with empirical and kinetic NO{sub x} modelling. Experiments were performed in three different wood stoves: a traditional stove, a staged air stove and a stove equipped with a catalytic afterburner. Ideally, biomass fuel does not give a net contribution to the greenhouse effect. However, incomplete combustion was found to result in significant greenhouse gas emissions. Empirical modelling showed the excess air ratio and the combustion chamber temperature to be the most important input variables controlling the total fuel-N to NO{sub x} conversion factor. As the result of an international round robin test of a wood stove equipped with a catalytic afterburner, particle emission measurements were found to be the best method to evaluate the environmental acceptability of the tested stove, since the particle emission level was least dependent of the national standards, test procedures and calculation procedures used. In batch single wood particle combustion experiments on an electrically heated small-scale fixed bed reactor the fuel-N to NO conversion factor varied between 0.11-0.86 depending on wood species and operating conditions. A parameter study and homogeneous kinetic modelling on a plug flow reactor showed that, depending on the combustion compliance in question, there is an optimum combination of primary excess air ratio, temperature and residence time that gives a maximum conversion of fuel-N to N{sub 2}. 70 refs., 100 figs., 26 tabs.

  2. Wood handbook : wood as an engineering material

    Science.gov (United States)

    Robert J. Ross; Forest Products Laboratory. USDA Forest Service.

    2010-01-01

    Summarizes information on wood as an engineering material. Presents properties of wood and wood-based products of particular concern to the architect and engineer. Includes discussion of designing with wood and wood-based products along with some pertinent uses.

  3. Changes in the Chemical Composition of Plum Distillate During Maturation with Oak Chips under Different Conditions.

    Science.gov (United States)

    Balcerek, Maria; Pielech-Przybylska, Katarzyna; Dziekońska-Kubczak, Urszula; Patelski, Piotr; Strąk, Ewelina

    2017-09-01

    This study investigates the effect of ageing on the qualitative and quantitative composition of plum distillate in contact with oak wood chips. Maturation was performed with lightly toasted French oak ( Quercus sessiflora and Quercus robur ) chips or oak chips made from fragments of empty barrels that had been used for ageing cognac. The effects of oak chip dose, process temperature, ageing system (static or circulatory) and ultrasound treatment were assessed. Maturation of plum distillate samples with oak chips resulted in higher levels of extractable organics (including tannins) and colour changes, which were correlated with the type and dose of oak chips, and the conditions of maturation. The content of sugars such as glucose, xylose and arabinose also increased, depending on the conditions and type of oak chips. Degradation of lignin resulted in liberation of sinapaldehyde, syringaldehyde, coniferaldehyde and vanillin, with intensities depending on the applied parameters. In terms of volatiles, decreases in the concentration of higher alcohols and aliphatic aldehydes were observed in the majority of maturation experiments, while concentrations of furanic aldehydes increased depending on the type and dose of oak chips, as well as on the conditions of maturation. The quantities of esters such as ethyl acetate decreased in the majority of experimental variants, whereas concentrations of ethyl caproate, ethyl caprylate and ethyl caprate increased gradually. Some phenols and lactones were detected in all matured samples, with the lowest levels found in the samples aged with oak chips made from cognac barrels.

  4. Wood combustion and NOx formation control

    International Nuclear Information System (INIS)

    Tewksbury, C.

    1991-01-01

    The control of wood combustion on stoker fed grates for optimum efficiency and the limiting of NO x (oxides of nitrogen) formation are not necessarily contradictory. This paper presents a matrix of air/fuel ratio control options, then discusses simple on-line monitoring techniques and the importance of operator training and alertness. The significance of uniform fuel feed and air distribution is emphasized. The relationships between combustion control and NO x formation are outlined both in theory and as tested. The experience of the McNeil Generating Station (the largest wood-fired, single boiler, stoker grate, utility electric generating station in the world) is used to demonstrate the theoretical principles. It has been observed that NO x emissions firing 100% whole tree chips with moisture contents as low as 40% by weight can be as low as 0.13 lb/MMBtu (MMBtu = 10 6 Btu) while still achieving a boiler efficiency in the range of 68% to 73% (in the high end of the design range) without the use of post-combustion treatment or flue gas recirculation (FGR). Problems of combustion and emissions control at steaming rates other than normal full-load are also examined. 2 figs., 4 tabs

  5. Real test-bed studies at the ETH House of Natural Resources – wood surface protection for outdoor applications

    Directory of Open Access Journals (Sweden)

    H. Guo

    2018-02-01

    Full Text Available The increasing demand for sustainable construction materials used in urban areas calls for novel wood protective coatings, which retain the natural appearance of wood while minimizing maintenance intervals. This work reports on three different wood surface modification processes and evaluates their protective effect against weathering after installation at a testing façade of the ETH House of Natural Resources (HoNR, a recently opened living lab located in Zürich, Switzerland. We monitored the discoloration upon outdoor exposure of subsequently improved generations of thin metal oxide coatings developed in our lab. We target almost transparent and durable coatings with water repellent properties to diminish discoloration due to UV light and biological attack. This should lead to wooden facades with increased reliability and thereby boost an enhanced utilization of the renewable and CO2 storing resource wood.

  6. Characteristics and Influence to Fruit Distillates Quality of Rapid Induction of Ageing Character in the Presence of Mulberry Tree (Morus alba L. Wooden Chips

    Directory of Open Access Journals (Sweden)

    Elena MUDURA

    2016-11-01

    Full Text Available Research on rapid induction of ageing character to double distilled traditional fruit brandies, from Transylvania region was conducted. Mulberry tree chips were used as an alternative to traditional ageing in wooden barrels. The aim of this study was to highlight the factors influencing the chemical composition of fruit brandies, both depending on the type of the wood used and the transformations occurred during the heat treatment. Fruit distillates were produced after the traditional method – double distillation in copper alambic. The evaluation of the brandies consisted in analyzing the chemical parameters and the phenolic compounds after two months of ageing with wood chips. Results were compared with a control sample (unaged distillate, and found that during the ageing process volatile and non-volatile compounds were extracted significantly. The heat treatment influenced the chemical composition of the wooden chips. The chemical composition of finished products varied due to the composition of the wooden chips used and to the heat treatment applied. Evaluation of volatile and non-volatile compounds formed was carried out by comparison with the samples of the unaged distillate. It was demonstrated the improvement of chemical characteristics and polyphenolic compounds content, by rapidly inducing of the ageing character.

  7. State of the art and the future fuel portfolio of fluidized bed combustion systems; Status und kuenftiges Brennstoffportfolio bei Wirbelschichtfeuerungen

    Energy Technology Data Exchange (ETDEWEB)

    Szentannai, Pal; Friebert, Arpad; Winter, Franz [Technische Univ. Wien (Austria). Inst. fuer Verfahrens-, Umwelttechnik und technische Biowissenschaften

    2008-07-01

    Coal, biomass and substitute fuels energetically can be used efficiently and with low pollution in fluidized bed plants. In comparison to biomass there are significant differences between the circulating and stationary fluidized bed technology. The stationary fluidised bed is fed predominantly with biomasses and residual substances. Coal usually is the basis fuel in the circulating fluidised bed. Biomass and residual substances frequently are course-fired. The state of the art is the employment of a broad fuel mixture in small and large fluidized-bed combustion systems. Future developments present an increased use of sewage sludge, fluidized bed combustion systems with wood as a basis fuel, utilization of household waste and the gas production.

  8. WOOD PROPERTIES AND EFFECT OF WOOD PROPERTIES ON THE WOOD FINISHING

    Directory of Open Access Journals (Sweden)

    Abdulkadir Malkoçoğlu

    2006-04-01

    Full Text Available Wood is basic raw material for furniture and joinery industries with wood structures. Wood is a biological material that has widely different properties depending on species, geographic area where the tree grew, the growth condition, size of the tree at harvest, sawing, and other manufacturing processes. Wood properties have been characterized within two groups as natural and manufacturing factors that effects finishing performance. Grow rate, density, knots, moisture content, extractives and juvenile wood are natural characteristics. Grain orientation, texture, drying and performance expectations are manufacturing characteristics. In this review, the effects of natural and manufacturing characteristics are discussed on the surface finishing performance of wood.

  9. Lagrangian Approach to Study Catalytic Fluidized Bed Reactors

    Science.gov (United States)

    Madi, Hossein; Hossein Madi Team; Marcelo Kaufman Rechulski Collaboration; Christian Ludwig Collaboration; Tilman Schildhauer Collaboration

    2013-03-01

    Lagrangian approach of fluidized bed reactors is a method, which simulates the movement of catalyst particles (caused by the fluidization) by changing the gas composition around them. Application of such an investigation is in the analysis of the state of catalysts and surface reactions under quasi-operando conditions. The hydrodynamics of catalyst particles within a fluidized bed reactor was studied to improve a Lagrangian approach. A fluidized bed methanation employed in the production of Synthetic Natural Gas from wood was chosen as the case study. The Lagrangian perspective was modified and improved to include different particle circulation patterns, which were investigated through this study. Experiments were designed to evaluate the concepts of the model. The results indicate that the setup is able to perform the designed experiments and a good agreement between the simulation and the experimental results were observed. It has been shown that fluidized bed reactors, as opposed to fixed beds, can be used to avoid the deactivation of the methanation catalyst due to carbon deposits. Carbon deposition on the catalysts tested with the Lagrangian approach was investigated by temperature programmed oxidation (TPO) analysis of ex-situ catalyst samples. This investigation was done to identify the effects of particles velocity and their circulation patterns on the amount and type of deposited carbon on the catalyst surface. Ecole Polytechnique Federale de Lausanne(EPFL), Paul Scherrer Institute (PSI)

  10. Importance of fragmentation on the steady state combustion of wood char in a bubbling fluidized bed

    Energy Technology Data Exchange (ETDEWEB)

    Pinho, Carlos [Universidade do Porto (CEFT/FEUP), Porto (Portugal). Faculdade de Engenharia. Centro de Estudos de Fenomenos de Transporte], E-mail: ctp@fe.up.pt

    2010-07-01

    A simple mathematical model for the analysis of the steady state behavior of a bubbling fluidized bed burner is presented, with the main intention of evaluating the importance of the primary fragmentation of fuel particles on the performance of this type of burners. This model has pedagogical advantages because of its simplicity and easiness of application to the analysis of realistic situations. The model is based upon the classical models used for the study of batch combustion processes in fluidized bed reactors. Experimental data from studies of fluidized bed combustion of portuguese vegetable chars are used to support the analysis of the performance of a 1 m diameter fluidized bed combustor. (author)

  11. Effect of residual wood on a morphology of mountain stream Cremos; Vplyv zvyskov dreva na morfologiu horskeho toku Cremos

    Energy Technology Data Exchange (ETDEWEB)

    Kralcakova, M [Univerzita Komenskeho v Bratislave, Prirodovedecka fakulta, Katedra fyzickej geografie a geoekologie, 84215 Bratislava (Slovakia)

    2012-04-25

    Several research papers are dedicated to the effect of wood in the river bed of the flow. It is done on the basis of empirical and theoretical knowledge. Globally, field research is practised on the application of knowledge on the impact of scrap wood mainly in the upstream mountain streams. The reason is that the flows founded in these altitudes are more likely inclined to supply wood because of forest cover area and the resulting consequences for a river-basin. In my research I mainly dealt with the impact of individual residues in stream sections of Cremos. During studying wood residues a determination of its variability was important. On the basis of this variability is important to define a classification of individual pieces of wood within the river-basin. (author)

  12. A comparative study on Cu, Cr and As removal from CCA-treated wood waste by dialytic and electrodialytic processes

    DEFF Research Database (Denmark)

    Velizarova, Emiliya; Ribeiro, Alexandra B.; Ottosen, Lisbeth M.

    2002-01-01

    with the performance of a pure dialytic experiment (without an external power supply) in order to reveal transport of charged particles induced solely by internal electrochemical potential differences in the system. Oxalic acid proved to be a more suitable pre-treatment solution than deionised water for wood chips...

  13. Biomass oxygen/steam gasification in a pressurized bubbling fluidized bed: Agglomeration behavior

    International Nuclear Information System (INIS)

    Zhou, Chunguang; Rosén, Christer; Engvall, Klas

    2016-01-01

    Highlights: • Dolomite is a superior material in preventing bed agglomeration. • Small molten ash particles deposited on magnesite at bed temperatures above 1000 °C. • The performance, when using magnesite, is sensitive to temperature disturbances. • The anti-agglomeration mechanisms of Ca- and Mg-bearing materials were discussed. - Abstract: In this study, the anti-agglomeration abilities of Ca- and Mg-containing bed materials, including dolomite and magnesite, in a pressurized bubbling fluidized bed gasifier using pine pellets and birch chips as feedstock, is investigated. The most typical bed material—silica sand—was also included as a reference for comparison. The sustainability of the operation was evaluated via analyzing the temperatures at different levels along the bed height. During the performances, the aim was to keep the temperature at the bottom zone of the reactor at around 870 °C. However, the success highly depends on the bed materials used in the bed and the temperature can vary significantly in case of agglomeration or bad mixing of bed materials and char particles. Both Glanshammar and Sala dolomites performed well with no observed agglomeration tendencies. In case of magnesite, the bed exhibited a high agglomeration tendency. Silica sand displayed the most severe agglomeration among all bed materials, even when birch chips with a low silica content was fed at a relatively low temperature. The solid samples of all the bed materials were inspected by light microscopy and Scanning Electron Microscopy (SEM). The Energy Dispersive Spectroscopy (EDS) detector was used to detect the elemental distribution in the surface. The crystal chemical structure was analyzed using X-ray Diffraction (XRD). Magnesite agglomerates glued together by big molten ash particles. There was no coating layer detected on magnesite particles at bed temperatures – below 870 °C. But when the temperature was above 1000 °C, a significant amount of small molten

  14. Large Combined Heat and Power Plants for Sustainable Energy System

    DEFF Research Database (Denmark)

    Lund, Rasmus Søgaard; Mathiesen, Brian Vad

    . CHP (combined heat and power) plants in Denmark will change their role from base load production to balancing the fluctuation in renewable energy supply, such as wind power and at the same time they have to change to renewable energy sources. Some solutions are already being planned by utilities...... in Denmark; conversion of pulverised fuel plants from coal to wood pellets and a circulating fluidised bed (CFB) plant for wood chips. From scientific research projects another solution is suggested as the most feasible; the combined cycle gas turbine (CCGT) plant. In this study a four scenarios...

  15. The effect of straw and wood gasification biochar on carbon sequestration, selected soil fertility indicators and functional groups in soil: an incubation study

    DEFF Research Database (Denmark)

    Hansen, Veronika; Müller-Stöver, Dorette; Munkholm, Lars Juhl

    2016-01-01

    Annual removal of crop residues may lead to depletion of soil organic carbon and soil degradation. Gasification biochar (GB), the carbon-rich byproduct of gasification of biomass such as straw and wood chips, may be used for maintaining the soil organic carbon content and counteract soil degradat......Annual removal of crop residues may lead to depletion of soil organic carbon and soil degradation. Gasification biochar (GB), the carbon-rich byproduct of gasification of biomass such as straw and wood chips, may be used for maintaining the soil organic carbon content and counteract soil......, the addition of straw resulted in a high soil respiration rate, and about 80% of the added carbonwas respired at the end of the incubation. However, the addition of straw increased aggregate stability and decreased clay dispersibility. Results from Fourier transformed infrared photoacoustic spectroscopy...

  16. Energy efficiency and CO{sub 2} -eq emissions of forest chip supply chains in Finland 2020

    Energy Technology Data Exchange (ETDEWEB)

    Kariniemi, A.; Kaerhae, K. (Metsaeteho Oy, Helsinki (Finland)), Email: arto.kariniemi@metsateho.fi, Email: kalle.karha@metsateho.fi

    2009-07-01

    The research carried out by Metsaeteho Oy calculated what would be the total fuel consumption and CO{sub 2}-eq emissions of forest chip production if the use of forest chips is 24 TWhin 2020 in Finland in accordance with the target set of Long-term Climate and Energy Strategy. CO{sub 2}-eq emissions were determined with Metsaeteho OY's updated Emissions Calculation Model. If the production and consumption of forest chips in Finland are 24 TWh in 2020, then the total CO{sub 2}-eq emissions would be around 245000 tonnes. The volume of diesel consumption was 79 million litres and petrol 1,5 millions litres. Electric rail transportation and chipping at the mill site consumed 15 GWh of electricity. The supply chain with the lowest CO{sub 2}-eq emissions was logging residues comminuted at plant. Conversely, the highest CO{sub 2}-eq emissions came from stump wood when operating with terminal comminuting. Some 3% of the energy content was consumed during the forest chip production. Energy input/output ratio in the total volume was 0.030 MWh/MWh which varied from 0.022 to 0.044 between the supply systems researched. Hence, forest chip production gave a net of some 97% of the energy content delivered at the plant. (orig.)

  17. 1H Nuclear Magnetic Resonance of Lodgepole Pine Wood Chips Affected by the Mountain Pine Beetle

    OpenAIRE

    Todoruk, Tara M.; Hartley, Ian D.; Teymoori, Roshanak; Liang, Jianzhen; Peemoeller, Hartwig

    2010-01-01

    In this study, wood-water interactions of mountain pine beetle affected lodgepole pine were found to vary with time since death. Based on an analysis of magnetization components and spin-spin relaxation times from 1H NMR, it was determined that the mountain pine beetle attack does not affect the crystalline structure of the wood. Both the amorphous structure and the water components vary with time since death, which could be due to the fungi present after a mountain pine beetle attack, as wel...

  18. Timber Chips as the Insulation Material for Energy Saving in Prefabricated Offices

    Directory of Open Access Journals (Sweden)

    Yupeng Wang

    2016-06-01

    Full Text Available This research demonstrates the feasibility of a roof insulation method for prefabricated offices that uses vinyl packed timber chips to reduce air conditioning loads (hereinafter referred to as AC loads and which also improves indoor thermal comfort. The advantages of the new roof insulation method were revealed through comparing the impacts of four roof types on prefabricated offices. The AC load and indoor thermal comfort (surface temperature and air temperature were evaluated. The disposal of scrap timber discarded from building construction projects is costing money, and is also a waste of natural resources. The assessment of a new roof insulation method with timber chips demonstrates the advanced usage of timber chips, reducing the environmental load in the building construction process. On the other hand, since prefabricated offices have lower thermal storage capacities and are less airtight than RC (reinforced concrete or S (steel structured buildings, the AC load consumption and indoor thermal comfort exacerbation in prefabricated offices is more serious. Especially in summer, a large amount of solar energy absorption from the roof raises the indoor air temperature and significantly increases the cooling load. This research contributes to the environmental design for prefabricated offices, and develops a method for the reuse of wood chips.

  19. Wood : adhesives

    Science.gov (United States)

    A.H. Conner

    2001-01-01

    This chapter on wood adhesives includes: 1) Classification of wood adhesives 2) Thermosetting wood adhesives 3) Thermoplastic adhesives, 4) Wood adhesives based on natural sources 5) Nonconventional bonding of wood 6) Wood bonding.

  20. Enhanced oil recovery chemicals from renewable wood resources

    Energy Technology Data Exchange (ETDEWEB)

    Grune, W.N.; Compere, A.L.; Griffith, W.L.; Crenshaw, J.M.

    1979-04-01

    Most of the wood pulp in the U.S. is produced by cooking, or digesting, wood chips in a chemical solution. These pulping processes have effluent streams which contain dissolved lignins, lignin breakdown products, and carbohydrates. There is a substantial economic incentive to use these materials as feedstocks for the production of high-valued micellar flood chemicals. The pulp and paper industries have practiced chemical recovery for almost a century. The largest chemical recycle processes are the internal recycle of inorganic salts for reuse in pulping. This is coupled with the use of waste organic compounds in the liquor as a fuel for directly-fired evaporation processes. Diversion of effluent and low valued streams for chemical recovery using fermentation, purification, or synthesis methods appears technically feasible in several cases. The use of new recovery processes could yield a variety of different wood-effluent based products. Some of the sugar acids in pulping liquors might be used as sequestering agents in reservoirs where there are large amounts of multivalent cations in flood brines. Fermentation production of high viscosity polymers, sequestering agents, and coagent alcohols appears worth further investigation. Tall oil acids and their derivatives can be used as surfactants in some reservoirs. Some waste constituents may adsorb preferentially on formations and thereby reduce loss of surfactants and other higher-valued chemicals.

  1. Changes in the Chemical Composition of Plum Distillate During Maturation with Oak Chips under Different Conditions

    Directory of Open Access Journals (Sweden)

    Maria Balcerek

    2017-01-01

    Full Text Available This study investigates the eff ect of ageing on the qualitative and quantitative composition of plum distillate in contact with oak wood chips. Maturation was performed with lightly toasted French oak (Quercus sessifl ora and Quercus robur chips or oak chips made from fragments of empty barrels that had been used for ageing cognac. The eff ects of oak chip dose, process temperature, ageing system (static or circulatory and ultrasound treatment were assessed. Maturation of plum distillate samples with oak chips resulted in higher levels of extractable organics (including tannins and colour changes, which were correlated with the type and dose of oak chips, and the conditions of maturation. The content of sugars such as glucose, xylose and arabinose also increased, depending on the conditions and type of oak chips. Degradation of lignin resulted in liberation of sinapaldehyde, syringaldehyde, coniferaldehyde and vanillin, with intensities depending on the applied parameters. In terms of volatiles, decreases in the concentration of higher alcohols and aliphatic aldehydes were observed in the majority of maturation experiments, while concentrations of furanic aldehydes increased depending on the type and dose of oak chips, as well as on the conditions of maturation. The quantities of esters such as ethyl acetate decreased in the majority of experimental variants, whereas concentrations of ethyl caproate, ethyl caprylate and ethyl caprate increased gradually. Some phenols and lactones were detected in all matured samples, with the lowest levels found in the samples aged with oak chips made from cognac barrels.

  2. Wood residue production and utilization research at Virgina Tech

    Energy Technology Data Exchange (ETDEWEB)

    Grace, L.A.; Stuart, W.B.; Sharp, J.C. (Virginia Polytechnic Inst. and State Univ., Blacksburg, VA (US)); Yu Jian-guo (Northeastern Forestry Univ., Harbin (CN))

    1988-01-01

    This paper describes the activities in crushing, drying and segregating wood residues currently underway at Virginia Tech. Experiments with high speed roll crushing as a means of reducing logging residues and small diameter stems to a form suitable for transportation and further processing appear promising. Deflecting whole tree chip streams across a double set of screens coupled with stripping transport air has been shown to reduce bark content and remove fines, bark and grit. Testing and refinement of two prototype sawdust driers is currently under way. Both driers offer increased opportunity for suspension burning and transport. (4 refs., 3 tabs., 3 figs.) (au).

  3. Ecological impacts of Synthetic Natural Gas from wood (SNG) used in current heating and car systems

    Energy Technology Data Exchange (ETDEWEB)

    Felder, R.; Dones, R.

    2007-07-01

    This illustrated poster illustrates how synthetic natural gas (SNG) from wood is a promising option to partially substitute fossil energy carriers. The comprehensive life cycle-based ecological impact of SNG is compared with that of natural gas, fuel oil, petrol/diesel, and wood chips that deliver the same services. The methods used for comparison, including Eco-indicator '99 perspectives, Eco-scarcity '97 (UBP), IPCC (2001), and external costs are discussed. The results indicate best ecological performance of the SNG system if consumption of fossil resources is strongly weighted. The performance of natural gas and wood-based systems are also discussed. The main negative aspects of the SNG system are discussed, as is the better ecological score of wood when highly-efficient particulate matter filters are installed. SNG is quoted as performing better than oil derivatives. External costs for SNG are examined. The authors recommend that SNG should preferably be used in cars, since the reduction of overall ecological impact and external costs when substituting oil-based fuels is higher for cars than for heating systems.

  4. Utilization of peat procurement network for purchase of energy wood. Subproject

    International Nuclear Information System (INIS)

    Kiukaanniemi, E.; Tervo, M.

    1998-01-01

    The objective of the project is to investigate and develop the energy wood procurement to the mire-terminals for production of mixed fuels, carried out by the peat contractors and forest machine entrepreneurs. The investigation of the costs of the chips produced for mixed fuels, the deviation of them and the possibilities to reduce them form the main part of the project. The duration of the project is two years, and it started in the summer 1997. Procurement of energy wood, carried out by forest machine and peat entrepreneurs, to the bog terminals for production of mixed fuels by the side of peat, will be studied in the project both experimentally and calculationally. The utilization of peat procurement network for energy wood procurement will mainly be studied. Costs and the harvesting logistics will be estimated using the software developed in the research. The project is divided into five sub-tasks: (1) survey on the contractor and machine needs of the experimental work; (2) selection of entrepreneurs and the harvesting sites; (3) practical harvesting experiments; (4) development of the cost calculation software; (5) analysis and reporting of the results

  5. Wood as an energy source in the 1990s

    International Nuclear Information System (INIS)

    Pohjonen, V.

    1993-01-01

    Woodbased fuels cover 14 % of the Finnish energy demand in the beginning of 1990s. Over half (55 %) of the wood power is generated in the cellulose industries by burning the residual black and sulphite liquor. A quarter (23 %) of the woodpower comes from mechanical wood residues, whereas 22 % only comes from conventional firewood. Based on the efficiency of the wood-based energy economy the cellulose and saw milling industries managed in the 1980s to exceed self sufficiency in electricity and steam power production. Increasing use of wood-based fuels in the future in nationally significant scale is therefore tied with the future growth of the cellulose and sawmilling industries. The growth has been made possible by the growth in the Finnish forests since the 1970s. A new model of power generation has been created in the town of Kuhmo in the eastern Finland. It is based on a modem saw mill, combined with electricity (5 MW) and district heating power (13 MW) plant. The power technology is based on fluidized bed combustion which has also been designed for minimizing the nitrogen emissions. Because woodbased fuels are sulphur free, and their impact in carbon balance can be kept in zero, increasing use of woodpower in Finland in the 1990s suits well in the international trends of sustained development

  6. The incorporation of wood waste ash as a partial cement replacement material for making structural grade concrete: An overview

    Directory of Open Access Journals (Sweden)

    Swaptik Chowdhury

    2015-06-01

    Full Text Available With increasing industrialization, the industrial byproducts (wastes are being accumulated to a large extent, leading to environmental and economic concerns related to their disposal (land filling. Wood ash is the residue produced from the incineration of wood and its products (chips, saw dust, bark for power generation or other uses. Cement is an energy extensive industrial commodity and leads to the emission of a vast amount of greenhouse gases, forcing researchers to look for an alternative, such as a sustainable building practice. This paper presents an overview of the work and studies done on the incorporation of wood ash as partial replacement of cement in concrete from the year 1991 to 2012. The aspects of wood ash such as its physical, chemical, mineralogical and elemental characteristics as well as the influence of wood ash on properties such as workability, water absorption, compressive strength, flexural rigidity test, split tensile test, bulk density, chloride permeability, freeze thaw and acid resistance of concrete have been discussed in detail.

  7. Wine consumption habits and consumer preferences between wines aged in barrels or with chips.

    Science.gov (United States)

    Pérez-Magariño, Silvia; Ortega-Heras, Miriam; González-Sanjosé, María Luisa

    2011-03-30

    The use of oak wood pieces in winemaking is increasing, but the acceptance of this technique by consumers is unknown. For that reason, the main aim of this study was to measure consumers' opinion of red wines made with this new technique, their acceptance of them and their intention to purchase these wines. A preference ranking test was also carried out. A specific questionnaire was drawn up for this study and 65 frequent red wine consumers tasted four wines, two aged traditionally in barrels and two macerated with chips, and a forced choice preference test was carried out. Fifty-five per cent of respondents said that they would not buy wines made using oak chips, although most respondents would buy these wines if, after tasting them, they were as pleasant and had the same quality as the wines aged traditionally in barrels. Wines obtained with oak wood fragments were not significantly rejected either by consumers who answered the questionnaire or by consumer tasters, which could be due to the large disparity of preferences found among tasters. The results clearly indicate that producers should develop each wine taking into account the specific preferences of each consumer group. Copyright © 2011 Society of Chemical Industry.

  8. The formation of impurities in fluidized-bed gasification of biomass, peat and coal; Epaepuhtauksien muodostuminen leijukerroskaasutuksessa

    Energy Technology Data Exchange (ETDEWEB)

    Kurkela, E.; Laatikainen-Luntama, J.; Kurkela, M.; Leppaelahti, J.; Koljonen, T.; Oesch, P. [VTT Energy, Espoo (Finland); Alen, R. [Jyvaeskylae Univ. (Finland)

    1996-12-01

    The objective of this three-year-long project was to study the effects of different process parameters and bed materials on the formation of impurities in pressurized fluidized-bed gasification. The main emphasis of the project was focused on the formation of tars and nitrogen compounds in wood, peat and coal gasification. The aims of the research were to find out such operating conditions, where the formation of problematic high-molecular-weight tars can be minimised and to create a better understanding on the fate of fuel nitrogen in fluidized-bed gasifiers. Main part of the research was carried out in a bench-scale pressurised fluidized-bed reactor (ID 30 mm), where the effects of pressure, temperature, gas atmosphere and bed material were studied with different feedstocks. Most of the test series were carried out using the same feedstocks as earlier used in the PDU-scale fluidized-bed gasification tests of VTT (pine wood, pine bark, wheat straw, two peats, Rhenish brown coal, Polish and Illinois No.6 bituminous coals). The effects of operating parameters on the product yields (gas components, tars, char) were first studied under inert nitrogen atmosphere. The conversion of fuel nitrogen into ammonia and HCN were also determined for the different feedstocks over the different operating conditions. These studies showed that ammonia is the main fixed nitrogen compound of fluidized-bed pyrolysis with all the feedstocks studied. The conversions of fuel nitrogen into ammonia and HCN was highest with the high volatile fuels and lowest with the two hard coals. Gas atmosphere had a dramatic effect on the conversion of fuel nitrogen; much higher ammonia yields were determined in real gasification gas atmosphere than in inert pyrolysis carried out in N{sub 2} or Argon atmosphere. In addition to the pressurised fluidized-bed pyrolysis tests, laboratory scale pyrolysis research was carried out in order to compare the pyrolysis behaviour of the different feedstocks

  9. Production of fungal volatile organic compounds in bedding materials

    OpenAIRE

    S. LAPPALAINEN; A. PASANEN; P. PASANEN

    2008-01-01

    The high relative humidity of the air and many potential growth media, such as bedding materials, hay and grains in the horse stable, for example, provide suitable conditions for fungal growth. Metabolic activity of four common agricultural fungi incubated in peat and wood shavings at 25°C and 4°C was characterized in this study using previously specified volatile metabolites of micro-organisms and CO 2 production as indicators. The volatile organic compounds were collected into Tenax resin a...

  10. Impact of utilization of alternative wood products of less conventional species (cherry and acacia) on the phenolic composition and sensory profile evolution of a red wine

    OpenAIRE

    Tavares, Mariana Ferreira Filipe

    2015-01-01

    Mestrado em Viticultura e Enologia - Instituto Superior de Agronomia / Faculdade de Ciências. Universidade do Porto The aim of this study was to evaluate the time-dependent changes, in the course of 90 days, in the phenolic and volatile composition and sensory properties in one red wine matured in contact with Portuguese (Quercus pyrenaica Willd.) and French (Quercus petraea L.) oak, acacia (Robina pseudoacacia) and cherry (Prunus Avium) wood chips and a cherry (Prunus avium) wood powder. ...

  11. Cord Wood Testing in a Non-Catalytic Wood Stove

    Energy Technology Data Exchange (ETDEWEB)

    Butcher, T. [Brookhaven National Lab. (BNL), Upton, NY (United States); Trojanowski, R. [Brookhaven National Lab. (BNL), Upton, NY (United States); Wei, G. [Brookhaven National Lab. (BNL), Upton, NY (United States)

    2014-06-30

    EPA Method 28 and the current wood stove regulations have been in-place since 1988. Recently, EPA proposed an update to the existing NSPS for wood stove regulations which includes a plan to transition from the current crib wood fuel to cord wood fuel for certification testing. Cord wood is seen as generally more representative of field conditions while the crib wood is seen as more repeatable. In any change of certification test fuel, there are questions about the impact on measured results and the correlation between tests with the two different fuels. The purpose of the work reported here is to provide data on the performance of a noncatalytic stove with cord wood. The stove selected has previously been certified with crib wood which provides a basis for comparison with cord wood. Overall, particulate emissions were found to be considerably higher with cord wood.

  12. Biomass gasification for liquid fuel production

    International Nuclear Information System (INIS)

    Najser, Jan; Peer, Václav; Vantuch, Martin

    2014-01-01

    In our old fix-bed autothermal gasifier we tested wood chips and wood pellets. We make experiments for Czech company producing agro pellets - pellets made from agricultural waste and fastrenewable natural resources. We tested pellets from wheat and rice straw and hay. These materials can be very perspective, because they dońt compete with food production, they were formed in sufficient quantity and in the place of their treatment. New installation is composed of allothermal biomass fixed bed gasifier with conditioning and using produced syngas for Fischer - Tropsch synthesis. As a gasifying agent will be used steam. Gas purification will have two parts - separation of dust particles using a hot filter and dolomite reactor for decomposition of tars. In next steps, gas will be cooled, compressed and removed of sulphur and chlorine compounds and carbon dioxide. This syngas will be used for liquid fuel synthesis

  13. Biomass gasification for liquid fuel production

    Energy Technology Data Exchange (ETDEWEB)

    Najser, Jan, E-mail: jan.najser@vsb.cz, E-mail: vaclav.peer@vsb.cz; Peer, Václav, E-mail: jan.najser@vsb.cz, E-mail: vaclav.peer@vsb.cz [VSB - Technical university of Ostrava, Energy Research Center, 17. listopadu 15/2172, 708 33 Ostrava-Poruba (Czech Republic); Vantuch, Martin [University of Zilina, Faculty of Mechanical Engineering, Department of Power Engineering, Univerzitna 1, 010 26 Zilina (Slovakia)

    2014-08-06

    In our old fix-bed autothermal gasifier we tested wood chips and wood pellets. We make experiments for Czech company producing agro pellets - pellets made from agricultural waste and fastrenewable natural resources. We tested pellets from wheat and rice straw and hay. These materials can be very perspective, because they dońt compete with food production, they were formed in sufficient quantity and in the place of their treatment. New installation is composed of allothermal biomass fixed bed gasifier with conditioning and using produced syngas for Fischer - Tropsch synthesis. As a gasifying agent will be used steam. Gas purification will have two parts - separation of dust particles using a hot filter and dolomite reactor for decomposition of tars. In next steps, gas will be cooled, compressed and removed of sulphur and chlorine compounds and carbon dioxide. This syngas will be used for liquid fuel synthesis.

  14. Impact of initial spacing on yield per acre and wood quality of unthinned loblolly pine at age 21

    Science.gov (United States)

    Alexander, III Clark; Richard F. Daniels; Lewis Jordan; Laurie Schimleck

    2010-01-01

    The market for southern pine first thinnings is soft. Thus, forest managers are planting at wider spacings, and using weed control and fertilization to grow chipping-saw and sawtimber trees in shorter rotations. A 21-year-old unthinned spacing study was sampled to determine the effect of initial spacing on wood quality and yield per acre of planted loblolly pine (

  15. In-Situ Measurement of the Transversal Dispersion in Ordered and Disordered 2D-pillar Beds for Liquid Chromatography

    NARCIS (Netherlands)

    de Bruyne, S.; de Malsche, Wim; Deridder, S.; Gardeniers, Johannes G.E.; Desmet, G.

    2014-01-01

    Using a fully transparent micropillar array chip and an optical “injection” setup capable of writing pulsed and continuous patterns into the flow by uncaging a fluorescent dye, highly detailed measurements of the transversal dispersion process in two-dimensional (2D) chromatographic beds could be

  16. Passive Imagery Navigation

    Science.gov (United States)

    1980-12-15

    SEASONAL CHANGES Unusually shaped wooded areas in winter. Open country and frozen lakes in winter unless Dry river beds if they contrast with in forested...representation or image chips for correlation matching o Processing Techniques (Indication of threshold settings, and which low-level processing techniques are...2U.9AY O LCHE lCA , OPIO LMSC-D767313 Next, the areas of the first image which were covered by landmarks are blocked out and interesting

  17. Longevity of Wood-Forced Pools in an Old-Growth Forest

    Science.gov (United States)

    Buffington, J. M.; Woodsmith, R. D.; Johnson, A. C.

    2009-12-01

    Wood debris plays an important role in scouring pools in forest channels and providing resultant habitat for aquatic organisms. We investigated the longevity of such pools in a gravel-bed river flowing through old-growth forest in southeastern Alaska by aging trees and “bear’s bread” fungi (Ganoderma applanatum, Fomitopsis pinicola) growing on pool-forming wood debris. Ages were determined by counting annual growth rings from cores and cross sections of trees and fungi growing on the wood debris. These ages are minimum values because they do not account for lag time between debris recruitment and seedling/spore establishment on the debris, nor do they account for flood scour that may periodically reset tree and fungi growth on the debris. The study stream has a gradient of about 1%, bankfull width and depth of 13.3 and 0.78 m, respectively, median grain size of 18 mm, a high wood loading (0.8 pieces/m), and a correspondingly low pool spacing (0.3 bankfull widths/pool), with 81% of the pools forced by wood debris. The size of wood debris in the study stream is large relative to the channel (average log length of 7.6 m and diameter of 0.35 m), rendering most debris immobile. Eighty-one pool-forming pieces of wood were dated over 1.2 km of stream length, with 28% of these pieces causing scour of more than one pool. In all, 122 wood-forced pools were dated, accounting for 38% of all pools at the site and 47% of the wood-forced pools. Fifty-three percent of the wood-forced pools lacked datable wood because these pieces either: were newly recruited; had been scoured by floods; or were contained below the active channel elevation, prohibiting vegetation establishment on the wood debris (the most common cause). The debris age distribution declined exponentially from 2 to 113 yrs., with a median value of 18 yrs. Similar exponential residence time distributions have been reported in other studies, but our analysis focused specifically on the ages of pool-forming wood

  18. Electrodialytic remediation of fly ash from co-combustion of wood and straw

    DEFF Research Database (Denmark)

    Chen, Wan; Jensen, Pernille Erland; Ottosen, Lisbeth M.

    2015-01-01

    The heavy metal content in fly ash from biomass combustion, such as straw, wood and sludge, often needs reducing before the ash can be used as fertilizer for agricultural land or as a component in the production of construction materials. In this study, fly ash from a boiler fueled with wood chips...... and straw was treated either by electrodialytic remediation (EDR) directly or by a combination of EDR and pre-wash with distilled water to investigate the possibilities of reducing the heavy metal content and reusing nutrients as fertilizer and bulk material in construction materials. Different experimental....../pre-wash-EDR treated ash mainly contained quartz, and the X-ray diffraction (XRD) peaks of K salts had disappeared. This shows that the potassium fertilizer potential was lost in the treated ashes, but the quartz mineral is beneficial in construction materials, such as ceramics. The K fertilizer could be recovered...

  19. Assessment of the wood waste resource and its position in the wood / wood-energy sector - Synthesis

    International Nuclear Information System (INIS)

    Guinard, Ludovic; Deroubaix, Gerard; Roux, Marie-Lise; Levet, Anne-Laure; Quint, Vincent

    2015-04-01

    The first objective of this study is to obtain a better knowledge of the 'wood wastes' issue, to propose a photography of the wood waste sector (productions, trades, consumptions), and then to elaborate different prospective scenarios on the use of wood waste volumes while taking into account possible evolutions on the medium or short term of the regulation and market of the wood/wood energy sector. The considered wastes come from industrial production, from the use of wood-based products, and from the end of life of products potentially containing wood. The authors present bibliographical sources and the adopted methodology, briefly describe the 'wood waste' system with its actors, and then report their assessment of wood wastes. They propose a global assessment as well as detailed assessments with respect to waste origins: wood trade and distribution, industries, craft, households and communities, building sector, public and private tertiary sector, packaging. They also address the collection and management of wood wastes by public services, and present the different types of valorisation (panel fabrication, energy, and others). They discuss exports, and then present different scenarios: a trend-based scenario, and two prospective scenarios with a priority to energetic valorisation or to material valorisation of wood wastes. These scenarios are compared

  20. Co-gasification of pelletized wood residues

    Energy Technology Data Exchange (ETDEWEB)

    Carlos A. Alzate; Farid Chejne; Carlos F. Valdes; Arturo Berrio; Javier De La Cruz; Carlos A. Londono [Universidad Nacional de Colombia, Antioquia (Colombia). Grupo de Termodinamica Aplicada y Energias Alternativas

    2009-03-15

    A pelletization process was designed which produces cylindrical pellets 8 mm in length and 4 mm in diameter. These ones were manufactured using a blend of Pinus Patula and Cypress sawdust and coal in proportions of 0%, 5%, 10%, 20%, and 30% v/v of coal of rank sub-bituminous extracted from the Nech mine (Amaga-Antioquia). For this procedure, sodium carboxymethyl cellulose (CMC) was used as binder at three different concentrations. The co-gasification experiments were carried out with two kinds of mixtures, the first one was composed of granular coal and pellets of 100% wood and the second one was composed of pulverized wood and granular coal pellets. All samples were co-gasified with steam by using an electrical heated fluidized-bed reactor, operating in batches, at 850{sup o}C. The main components of the gaseous product were H{sub 2}, CO, CO{sub 2}, CH{sub 4}, and N{sub 2} with approximate quantities of 59%, 6.0%, 20%, 5.0%, and 9.0% v/v, respectively, and the higher heating values ranged from between 7.1 and 9.5 MJ/Nm{sup 3}.

  1. Wood Export and Deposition Dynamics in Mountain Watersheds

    Science.gov (United States)

    Senter, Anne Elizabeth

    conditions and accompanying hydrologic responses. Chapter 2 contains development of new theory in support of the introduction of multiplicative coefficients, categorized by water year type, that were used to predict wood export quantities via utilization of an existing discharge-based theoretical equation. This new theory was the product of continued investigations into watershed-scale factors in search of explanation of observed variation of wood export rates into New Bullards Bar Reservoir. The gap between known variability and the attribution of wood export to one hydrologic relation continues to be a persistent issue, as the hierarchical and stochastic temporal and spatial nature of wood budget components remain difficult to quantify. The development of "watershed processes" coefficients was specifically focused on a generalized, parsimonious approach using water year type categories, with validation exercises supporting the approach. In dry years, predictions more closely represented observed wood export quantities, whereas the previously derived annual peak discharge relation yielded large over-predictions. Additional data are needed to continue development of these watershed-specific coefficients. This new approach to wood export prediction may be beneficial in regulated river systems for planning purposes, and its efficacy could be tested in other watersheds. Chapter 3 presents the results of an investigation into wood deposition mechanisms in a 12.2 km segment of the confined, bedrock-dominated South Yuba River watershed. Inclusion of coarse wood particles in the analyses was essential in recognizing depositional patterns, thus supporting the value of utilizing a wider wood-size range. A near-census data collection effort yielded myriad data, of which topographic wetted width and bed elevation data, developed for an observed 4.5-year flood event, were standardized in 10-m intervals and then univariate and linked values were ordered into landform classifications

  2. Can Acceptable Pulp be Obtained from Eucalyptus globulus Wood Chips after Hemicellulose Extraction?

    OpenAIRE

    Francisco López; M. Trinidad García; Vicente Mena; J. Mauricio Loaiza; Minerva A. M. Zamudio; Juan C. García

    2014-01-01

    This study investigates the operating conditions used in the soda-anthraquinone pulping of Eucalyptus globulus wood after autohydrolysis pretreatment on the yield, kappa number, and brightness of the resulting unbleached pulp. Moreover, strength-related properties of the resulting handsheets was examined to identify the best pulping conditions and compare the outcome with that of a conventional soda-anthraquinone pulping process. The paper strength properties of the pulp were similar to or be...

  3. Microfluidic magnetic fluidized bed for DNA analysis in continuous flow mode.

    Science.gov (United States)

    Hernández-Neuta, Iván; Pereiro, Iago; Ahlford, Annika; Ferraro, Davide; Zhang, Qiongdi; Viovy, Jean-Louis; Descroix, Stéphanie; Nilsson, Mats

    2018-04-15

    Magnetic solid phase substrates for biomolecule manipulation have become a valuable tool for simplification and automation of molecular biology protocols. However, the handling of magnetic particles inside microfluidic chips for miniaturized assays is often challenging due to inefficient mixing, aggregation, and the advanced instrumentation required for effective actuation. Here, we describe the use of a microfluidic magnetic fluidized bed approach that enables dynamic, highly efficient and simplified magnetic bead actuation for DNA analysis in a continuous flow platform with minimal technical requirements. We evaluate the performance of this approach by testing the efficiency of individual steps of a DNA assay based on padlock probes and rolling circle amplification. This assay comprises common nucleic acid analysis principles, such as hybridization, ligation, amplification and restriction digestion. We obtained efficiencies of up to 90% for these reactions with high throughput processing up to 120μL of DNA dilution at flow rates ranging from 1 to 5μL/min without compromising performance. The fluidized bed was 20-50% more efficient than a commercially available solution for microfluidic manipulation of magnetic beads. Moreover, to demonstrate the potential of this approach for integration into micro-total analysis systems, we optimized the production of a low-cost polymer based microarray and tested its analytical performance for integrated single-molecule digital read-out. Finally, we provide the proof-of-concept for a single-chamber microfluidic chip that combines the fluidized bed with the polymer microarray for a highly simplified and integrated magnetic bead-based DNA analyzer, with potential applications in diagnostics. Copyright © 2017 Elsevier B.V. All rights reserved.

  4. Recycling of impregnated wood and impregnating agents - combustion plant technology; Kyllaestetyn puutavaran ja kyllaestysaineiden kierraetys - polttolaitostekniikka

    Energy Technology Data Exchange (ETDEWEB)

    Syrjaenen, T.; Kangas, E. [Kestopuu Oy, Helsinki (Finland)

    2000-07-01

    purification systems cause extra investments. The emissions limits for combustion of impregnated wood are given in EU's Waste Incineration Directive. The amount of collected impregnated wood is sufficient for a 25 MW plant. Solid fuels fired gasification, grate firing and fluidized bed boilers suit best fir combustion of impregnated wood waste, gasification and fluidized beds being the best, because of the efficient combustion and low ash formation. Flue gas purification system is essential for incineration of impregnated wood. Chromium and copper, released in combustion, remain mainly in ash, but 60-90% of arsenic migrates in flue gases as small particles. By combining different technologies it is possible to obtain better recovery of impurities. One of the best methods is based on spraying of fluid in pre-cooling system into flue gases in order to cool the gases rapidly and to stop the reactions in the flue gases. After this the flue gases are pre-cleaned and cooled in a venturi scrubber. Fiber filters are recommended for dedusting of the flue gases. The formed ashes are recycled in Outokumpu Harjavalta metals copper smelter as raw material, which requires that the sintered material content of ash is low. The condensing waters of flue gas scrubbing can be used for preparation of copper/chromium/arsenic (CCA) concentrate.

  5. Fluidized bed combustion with the use of Greek solid fuels

    Directory of Open Access Journals (Sweden)

    Kakaras Emmanuel

    2003-01-01

    Full Text Available The paper is an overview of the results obtained up to date from the combustion and co-combustion activities with Greek brown coal in different installations, both in semi-industrial and laboratory scale. Combustion tests with Greek lignite were realized in three different Circulating Fluidized Bed Combustion (CFBC facilities. Low rank lignite was burned in a pilot scale facility of approx. 100kW thermal capacity, located in Athens (NTUA and a semi-industrial scale of 1.2 MW thermal capacity, located at RWE's power station Niederaussem in Germany. Co-combustion tests with Greek xylitic lignite and waste wood were carried out in the 1 MWth CFBC installation of AE&E, in Austria. Lab-scale co-combustion tests of Greek pre-dried lignite with biomass were accomplished in a bubbling fluidized bed in order to investigate ash melting problems. The obtained results of all aforementioned activities showed that fluidized bed is the appropriate combustion technology to efficiently exploit the low quality Greek brown coal either alone or in conjunction with biomass species.

  6. Silicon Chip-to-Chip Mode-Division Multiplexing

    DEFF Research Database (Denmark)

    Baumann, Jan Markus; Porto da Silva, Edson; Ding, Yunhong

    2018-01-01

    A chip-to-chip mode-division multiplexing connection is demonstrated using a pair of multiplexers/demultiplexers fabricated on the silicon-on-insulator platform. Successful mode multiplexing and demultiplexing is experimentally demonstrated, using the LP01, LP11a and LP11b modes.......A chip-to-chip mode-division multiplexing connection is demonstrated using a pair of multiplexers/demultiplexers fabricated on the silicon-on-insulator platform. Successful mode multiplexing and demultiplexing is experimentally demonstrated, using the LP01, LP11a and LP11b modes....

  7. Chapter 6: Wood energy and competing wood product markers

    Science.gov (United States)

    Kenneth E. Skog; Robert C. Abt; Karen Abt

    2014-01-01

    Understanding the effect of expanding wood energy markets is important to all wood-dependent industries and to policymakers debating the implementation of public programs to support the expansion of wood energy generation. A key factor in determining the feasibility of wood energy projects (e.g. wood boiler or pellet plant) is the long-term (i.e. 20-30year) supply...

  8. The effect of alkali treatment of bamboo on the physical and mechanical properties of particleboard made from bamboo - industrial wood particles

    Directory of Open Access Journals (Sweden)

    vahid vaziri

    2018-02-01

    Full Text Available In this study, physical and mechanical properties of single layer particleboard made from bamboo powder (with and without alkali treatment and wood particles were investigated. Bamboo powder (30 mesh particles was treated with 5% hydroxide sodium for 120 minutes. Industrial wood chips from Sanate Choube Shomal Company were used.The variable in this research were the ratio of bamboo powder (with and without alkali treatment to wood chips (at four levels; 0:100, 10:90, 20:80, 30:70. Urea formaldehyde resin used at 10 percent level of dry weight of raw material as well as ammonium chloride was used as a catalyst at 2 percent level of the dry weight of adhesive. Physical and mechanical properties of panels measured according to EN Standard. Mechanical properties of the particleboards made from treated bamboo was superior to the relevant untreated bamboo. Water absorption and thickness swelling after 2 and 24 hours immersion in water decreased with alkali treatment. Mercerization, or treating cellulose fibers in alkaline solution, because of fibrillation, the removal of lignin and hemicellulose enhances the mechanical properties and dimension stability of the particleboard by promoting resin-fiber mechanical interlocking at the interface. Results showed, there was usability of the treated bamboo up to 30 percent for general purpose boards for use in dry conditions.

  9. Wood adhesives : vital for producing most wood products

    Science.gov (United States)

    Charles R. Frihart

    2011-01-01

    A main route for the efficient utilization of wood resources is to reduce wood to small pieces and then bond them together (Frihart and Hunt 2010). Although humankind has been bonding wood since early Egyptian civilizations, the quality and quantity of bonded wood products has increased dramatically over the past 100 years with the development of new adhesives and...

  10. Studies of wood fuel systems with raw material from young forest stands. Final report; Systemstudier ungskogsbraensle. Slutrapport

    Energy Technology Data Exchange (ETDEWEB)

    Liss, J.E. [Dalarna Univ., Falun (Sweden)

    2001-12-01

    The three-year project 'Studies of wood fuel systems with raw material from young forest stands' has been carried out during the period March 1998 to February 2001. New technology for harvesting small trees has created a possibility to develop efficient wood fuel systems using raw material from young forest stands. This possibility coincides with a great demand for tending of young stands from a silvicultural point of view. The main aim of the project has been to analyse and assess wood fuel systems based on this concept. The spectrum of criteria for assessment has been broad, including productivity, profitability, safety and health aspects, employment and environmental impact. As an example of a new technology which has been developed and studied during the project period can be mentioned a new felling head which can be used for cutting and handling several trees at the same time. The weight of the felling head is only about 270 kg, which has done it possible to use it on smaller base-machines as well as larger machines. The productivity has shown to be about 150-250 trees/hour in stands with a diameter of 5-10 cm. The productivity, expressed as biomass, is about 2-3 tonnes dry substance/hour. In the design of production system, bundling of trees early in the process is considered to be especially promising. The development of such a system is ongoing, but is not at the market yet. Some experimental studies have been done on transportation, storing and chipping of such bundles with varying size and varying tree-species. The calculated cost of this system will be lower then for traditional chipping-systems, because of the higher density for the handle units. It is much easier to handle bundles than small non-bundled trees, the chipping-productivity will be high and the transportation can be done with regular timber trucks. The calculation cost for the bundle-system will be about 120-130 SEK/MWh in stands with a diameter of some 7-10 cm, which can be

  11. Quality of wooden chips produced by Claas Jaguar fitted with experimental CRA-ING rotor

    Energy Technology Data Exchange (ETDEWEB)

    Pari, L.; Civitarese, V.; Del Giudice, A. [Council for Research in Agriculture, Agricultural Engineering Research Unit, Rome (Italy)

    2010-07-01

    This paper described a newly developed chipper device for mounting on Claas Jaguar chipper harvesters for short rotation forestry harvesting. It was designed by the Agriculture Engineering Research Unit of the Agricultural Research Council in Rome, Italy. The new rotor has a lower number of blades compared to standard rotors and has a different cutting angle and drum insertion. This study evaluated the particle-size distribution of wood chips produced by standard rotors compared to those with the experimental rotor. The objective was to distinguish the particle size distribution of chips produced using the two types of chippers in order to evaluate the influence of wooden species in the chip formation process. Tests were conducted using 860 and 890 Claas Jaguar chipper harvesters, both equipped with standard and CRA-ING rotors. The experiment was conducted on poplar cultivations on biennial shift and on arboreal cultivations. Compared to traditional rotors, CRA-ING rotors provide a considerable product increase within particle sizes ranging from 12.5 to 25 mm, and an equivalent product reduction within the finest particle size classes. The study showed that the new rotor tends to concentrate dimensional increments along the longitudinal section of the chip, regardless of the species used. In order to obtain a better quality chip in terms of particle size, a second rotor was devised to engrave a cleaner cut on the biomass introduced by the feeding rollers.

  12. Environmental assessment of post-consumer wood and forest residues gasification: The case study of Barcelona metropolitan area

    International Nuclear Information System (INIS)

    Puy, Neus; Rieradevall, Joan; Bartroli, Jordi

    2010-01-01

    An energy and environmental analysis of post-consumer wood and forest residues gasification in metropolitan areas is carried out to determine the most critical stages of their life cycle. Life Cycle Impact Assessment (LCIA) methodology is used to identify the environmental load of three defined scenarios: (1) Post-consumer wood from recycling points; (2) Post-consumer wood from bulky wastes; and (3) Forest residues. The stages considered are biomass pre-treatment, transport and gasification. Biomass pre-treatment comprise different steps: separation, chipping, sifting, post-chipping for all the scenarios; except for the drying step which is only entailed to Scenario 3. The midpoint impact categories taken into account are: abiotic depletion (AD), global warming (GW), ozone layer depletion (ODP), human toxicity (HT), acidification (A) and eutrophication (E). Results show that, due to the high physical requirements for biomass gasification, the most appropriate biomass is that of Scenario 1, since forest residues require a drying stage, which involves high energy consumption and high environmental impact. Energy consumption in biomass pre-treatment and transport stages is low compared to the energy obtained from gasification, which represents the 5% in Scenario 1; 7% in Scenario 2; and 13% in Scenario 3. Biomass pre-treatment is associated to an important contribution in AD and ODP impact categories, calculated as 71% and 98% of the overall impact. The transport stage is of no significant influence either in the scenarios or in the impact categories (less than 24% of the overall impact). Finally, gasification represents an impact of 3-78% of the different impact categories. (author)

  13. Pilot-scale investigation of the robustness and efficiency of a copper-based treated wood wastes recycling process

    Energy Technology Data Exchange (ETDEWEB)

    Coudert, Lucie [INRS-ETE (Canada); Blais, Jean-François, E-mail: blaisjf@ete.inrs.ca [INRS-ETE (Canada); Mercier, Guy [INRS-ETE (Canada); Cooper, Paul [University of Toronto (Canada); Gastonguay, Louis [IREQ (Canada); Morris, Paul [FPInnovations (Canada); Janin, Amélie; Reynier, Nicolas [INRS-ETE (Canada)

    2013-10-15

    Highlights: • A leaching process was studied for metals removal from CCA-treated wood wastes. • This decontamination process was studied at pilot scale (130-L reactor). • Removals up to 98% of As, 88% of Cr, and 96% of Cu were obtained from wood wastes. • The produced leachates can be treated by chemical precipitation. -- Abstract: The disposal of metal-bearing treated wood wastes is becoming an environmental challenge. An efficient recycling process based on sulfuric acid leaching has been developed to remove metals from copper-based treated wood chips (0 < x < 12 mm). The present study explored the performance and the robustness of this technology in removing metals from copper-based treated wood wastes at a pilot plant scale (130-L reactor tank). After 3× 2 h leaching steps followed by 3× 7 min rinsing steps, up to 97.5% of As, 87.9% of Cr, and 96.1% of Cu were removed from CCA-treated wood wastes with different initial metal loading (>7.3 kg m{sup −3}) and more than 94.5% of Cu was removed from ACQ-, CA- and MCQ-treated wood. The treatment of effluents by precipitation–coagulation was highly efficient; allowing removals more than 93% for the As, Cr, and Cu contained in the effluent. The economic analysis included operating costs, indirect costs and revenues related to remediated wood sales. The economic analysis concluded that CCA-treated wood wastes remediation can lead to a benefit of 53.7 US$ t{sup −1} or a cost of 35.5 US$ t{sup −1} and that ACQ-, CA- and MCQ-treated wood wastes recycling led to benefits ranging from 9.3 to 21.2 US$ t{sup −1}.

  14. Wood frame systems for wood homes

    Directory of Open Access Journals (Sweden)

    Julio Cesar Molina

    2010-12-01

    Full Text Available The use of constructive systems that combine strength, speed, with competitive differential techniques and mainly, compromising with the environment, is becoming more popular in Brazil. The constructive system in wood frame for houses of up to five stories is very interesting, because it is a light system, structured in reforested treated wood which allows the combination of several materials, besides allowing speed in the construction and total control of the expenses already in the project phase for being industrialized. The structural behavior of the wood frame is superior to the structural masonry in strength, thermal and acoustic comfort. However, in Brazil, the wood frame is still little known and used, due to lack of technical knowledge about the system, prejudice associated the bad use of the wood as construction material, or still, in some cases, lack of normalization. The aim of this manuscript consists of presenting the main technical characteristics and advantages of the constructive system in wood frame homes, approaching the main stages of the constructive process through examples, showing the materials used in the construction, in addition the main international normative recommendations of the project. Thus, this manuscript also hopes to contribute to the popularization of the wood frame system in Brazil, since it is a competitive, fast and ecologically correct system. Moreover, nowadays, an enormous effort of the technical, commercial and industrial section has been accomplished for the development of this system in the country.

  15. Wood-based bioenergy value chain in mountain urban districts: An integrated environmental accounting framework

    International Nuclear Information System (INIS)

    Nikodinoska, Natasha; Buonocore, Elvira; Paletto, Alessandro; Franzese, Pier Paolo

    2017-01-01

    Highlights: • The Sarentino bioenergy value chain (North Italy) was investigated. • A multi-method environmental accounting framework was implemented. • Environmental costs and impacts of a forest bioenergy chain were assessed. • Indicators show a good environmental performance and sustainability. • Linking wood industry and energy production could lower the environmental burden. - Abstract: Using wood biomass for bioenergy production in mountain urban settlements can represent a win–win strategy when it combines a continuous energy provision to households with a sustainable management of local forests, also boosting rural development and stakeholders’ cooperation. In this study, we implemented a multi-method environmental accounting framework aimed at investigating environmental costs and impacts of a bioenergy value chain located in Sarentino Valley (North Italy). This assessment framework encompasses material, energy, and emergy demands as well as main emissions generated at each step of the chain: (1) forestry, (2) logistics, and (3) conversion. The resulting global to local ratios of abiotic material calculated for forestry, logistics, and conversion subsystems show that the global (direct and indirect) consumption of abiotic matter was respectively 3.6, 3.2, and 7.6 times higher than the direct material demand. The Energy Return on Energy Investment (EROI) of wood biomass and wood chips production (37.1 and 22.4) shows a high energy performance of these processes, while the EROI of heat generation (11.35) reflects a higher support of human-driven inputs. The emergy renewable fraction, ranging from 77% to 37% across the value chain, shows a high use of local renewable resources in the bioenergy value chain. The total CO_2 emissions of the bioenergy value chain (4088 t CO_2 yr"−"1) represent only 7.1% of the CO_2 sequestration potential of the Sarentino Valley forest ecosystem, highlighting the capability of the local forests to offset the CO_2

  16. Radioactivity of wood ash; Puun tuhkan radioaktiivisuus

    Energy Technology Data Exchange (ETDEWEB)

    Rantavaara, A.; Moring, M

    2000-01-01

    STUK (Finnish Radiation and Nuclear Safety Authority) has investigated natural and artificial radioactivity in wood ash and radiation exposure from radionuclides in ash since 1996. The aim was to consider both handling of ash and different ways of using ash. In all 87 ash samples were collected from 22 plants using entirely or partially wood for their energy production in 1996-1997. The sites studied represented mostly chemical forest industry, sawmills or district heat production. Most plants used fluidised bed combustion technique. Samples of both fly ash and bottom ash were studied. The activity concentrations of radionuclides in samples of, e.g., dried fly ash from fuel containing more than 80% wood were determined. The means ranged from 2000 to less than 50 Bq kg{sup -1}, in decreasing order: {sup 137}Cs, {sup 40}K, {sup 90}Sr, {sup 210}Pb,{sup 226}Ra, {sup 232}Th, {sup 134}Cs, {sup 235}U. In bott radionuclide contents decreased in the same order as in fly ash, but were smaller, and {sup 210}Pb was hardly detectable. The NH{sub 4}Ac extractable fractions of activities for isotopes of alkaline elements (K, Cs) in bottom ash were lower than in fly ash, whereas solubility of heavier isotopes was low. Safety requirements defined by STUK in ST-guide 12.2 for handling of peat ash were fulfilled at each of the sites. Use of ash for land-filling and construction of streets was minimal during the sampling period. Increasing this type of ash use had often needed further investigations, as description of the use of additional materials that attenuate radiation. Fertilisation of forests with wood ash adds slightly to the external irradiation in forests, but will mostly decrease doses received through use of timber, berries, mushrooms and game meat. (orig.)

  17. Temporal and spatial variability in thalweg profiles of a gravel-bed river

    Science.gov (United States)

    Madej, Mary Ann

    1999-01-01

    This study used successive longitudinal thalweg profiles in gravel-bed rivers to monitor changes in bed topography following floods and associated large sediment inputs. Variations in channel bed elevations, distributions of residual water depths, percentage of channel length occupied by riffles, and a spatial autocorrelation coefficient (Moran's I) were used to quantify changes in morphological diversity and spatial structure in Redwood Creek basin, northwestern California. Bed topography in Redwood Creek and its major tributaries consists primarily of a series of pools and riffles. The size, frequency and spatial distribution of the pools and riffles have changed significantly during the past 20 years. Following large floods and high sediment input in Redwood Creek and its tributaries in 1975, variation in channel bed elevations was low and the percentage of the channel length occupied by riffles was high. Over the next 20 years, variation in bed elevations increased while the length of channel occupied by riffles decreased. An index [(standard deviation of residual water depth/bankfull depth) × 100] was developed to compare variations in bed elevation over a range of stream sizes, with a higher index being indicative of greater morphological diversity. Spatial autocorrelation in the bed elevation data was apparent at both fine and coarse scales in many of the thalweg profiles and the observed spatial pattern of bed elevations was found to be related to the dominant channel material and the time since disturbance. River reaches in which forced pools dominated, and in which large woody debris and bed particles could not be easily mobilized, exhibited a random distribution of bed elevations. In contrast, in reaches where alternate bars dominated, and both wood and gravel were readily transported, regularly spaced bed topography developed at a spacing that increased with time since disturbance. This pattern of regularly spaced bed features was reversed

  18. Wood

    DEFF Research Database (Denmark)

    Unterrainer, Walter

    2014-01-01

    come from? How is it harvested? How is it manufactured and treated ? How are the buildings detailed and protected against weather during construction to keep them dry and make them long-life ? In a period of climate change, forests are the last lungs of the planet to sequestrate CO2. Their global size......Wood – a sustainable building material ? For thousands of years and all over the planet, wood has been used as a building material and exciting architecture has been created in wood. The fantastic structural, physical and aesthetic properties of the material as well as the fact that wood...

  19. Wood burning

    Energy Technology Data Exchange (ETDEWEB)

    Winkelmann, H

    1955-01-01

    Discussed are the use of wood as a fuel, the technique of wood combustion and the operation of wood-burning stoves for cooking and heating. In addition, there is a section which reviews the use of wood stoves in various countries and lists manufacturers of stoves, central heating furnaces and in some cases sawdust burners.

  20. Effect of wood fuels on power plant operability

    International Nuclear Information System (INIS)

    Orjala, M.; Ingalsuo, R.

    2001-01-01

    The objective of the research is to determine the critical properties of wood fuels on the basis of power plant operability, to determine the optimal conditions for reduction of harmful detriments, and to study how the storage and processing of wood fuels effect on the operability. Both the CFB and BFB technologies are studied. The project started in December 2000 and it will be ended by the end of 2002. Experts of the Fuels and Combustion research field of VTT Energy carry out the main parts of the research. Experts of the research field of Mineral Processing of VTT Chemical Technology, located in Outokumpu, and Kemian tutkimuspalvelut Oy/Oulu University, located in Outokumpu, participate in the analytics, and the research field of Materials and Manufacturing Technology of VTT Manufacturing Technology in Otaniemi participates in the research on material effects. System Technology Laboratory of Oulu University carries out the power plant automation and boiler control technology research under supervision of Professor Urpo Kortela. Co-operation with the materials research unit of EU's JRC, located in Petten, which started in the research 'Combustion of Forest Chips', will be continues in this research. Co-operation will be made with Swedish Vaermeforsk in the field of information exchange on experiences in utilisation of wood fuels in Swedish power plants and possibilities to join in the projects of Vaermeforsk in this research field. Following companies participate in the project: Etelae-Savon Energia Oy, Foster Wheeler Energia Oy, Kvaerner Pulping Oy, Simpele pasteboard factory of M-Real Oyj and Vaermeforsk AB (Sweden). (orig.)

  1. Carbon and energy balances for a range of biofuels options

    Energy Technology Data Exchange (ETDEWEB)

    Elsayed, M.A.; Matthews, R.; Mortimer, N.D.

    2003-03-01

    This is the final report of a project to produce a set of baseline energy and carbon balances for a range of electricity, heat and transport fuel production systems based on biomass feedstocks. A list of 18 important biofuel technologies in the UK was selected for study of their energy and carbon balances in a consistent approach. Existing studies on these biofuel options were reviewed and their main features identified in terms of energy input, greenhouse gas emissions (carbon dioxide, methane, nitrous oxide and total), transparency and relevance. Flow charts were produced to represent the key stages of the production of biomass and its conversion to biofuels. Outputs from the study included primary energy input per delivered energy output, carbon dioxide outputs per delivered energy output, methane output per delivered energy output, nitrous oxide output per delivered energy output and total greenhouse gas requirements. The net calorific value of the biofuel is given where relevant. Biofuels studied included: biodiesel from oilseed rape and recycled vegetable oil; combined heat and power (CHP) by combustion of wood chip from forestry residues; CHP by gasification of wood chip from short rotation coppice; electricity from the combustion of miscanthus, straw, wood chip from forestry residues and wood chip from short rotation coppice; electricity from gasification of wood chip from forestry residues and wood chip from short rotation coppice; electricity by pyrolysis of wood chip from forestry residues and wood chip from short rotation coppice; ethanol from lignocellulosics, sugar beet and wheat; heat (small scale) from combustion of wood chip from forestry residues and wood chip from short rotation coppice; and rapeseed oil from oilseed rape.

  2. Impact of alternative technique to ageing using oak chips in alcoholic or in malolactic fermentation on volatile and sensory composition of red wines.

    Science.gov (United States)

    Gómez García-Carpintero, E; Gómez Gallego, M A; Sánchez-Palomo, E; González Viñas, M A

    2012-09-15

    This paper reports on a complete study of the effect of wood, in the form of oak chips, on the volatile composition and sensory characteristics of Moravia Agria wines added at different stages of the fermentation process. Aroma compounds were analyzed by gas chromatography-mass spectrometry (GC-MS). Sensory profile was evaluated by experienced wine-testers. Oak chips were added to wines in two dose rates at different stages of the winemaking process: during alcoholic fermentation (AF), during malolactic fermentation (MLF) and in young, red Moravia Agria wine. Wines fermented with oak chips during AF showed higher concentrations of the ethyl esters of straight-chain fatty acids, ethyl, hexyl, isoamyl acetates and superior alcohols than the control wines. The higher concentrations of benzene compound, oak lactones and furanic compounds were found in wines in contact with oak chips during MLF. The use of oak chips gives rise to a different sensorial profile of wines depending of the point of addition. Higher intensities of woody, coconut, vanilla and sweet spices descriptors were obtained when a large dose rate of chips was employed. Copyright © 2012 Elsevier Ltd. All rights reserved.

  3. Effects of feeding level and access to rooting material on behaviour of growing pigs in situations with reduced feeding space and delayed feeding

    DEFF Research Database (Denmark)

    Jensen, Margit Bak; Pedersen, Lene Juul

    2010-01-01

    Seventy-two pigs, housed in groups of four, were allocated to either (1) ad libitum feeding with access to wood chip, (2) restrictive feeding with access to wood chip or (3) restrictive feeding without access to wood chip. The effects of feeding level (treatment 1 vs. 2) and access to wood chip......, but the level of manipulating floor in these pigs did not reach the level of manipulating wood chip among pigs on treatment 2. During normal days restrictively fed pigs spent less time feeding on a 24 h basis, but more time feeding during the first hour after feed allocation than ad libitum fed pigs. When...

  4. Flip chip assembly of thinned chips for hybrid pixel detector applications

    International Nuclear Information System (INIS)

    Fritzsch, T; Zoschke, K; Rothermund, M; Oppermann, H; Woehrmann, M; Ehrmann, O; Lang, K D; Huegging, F

    2014-01-01

    There is a steady trend to ultra-thin microelectronic devices. Especially for future particle detector systems a reduced readout chip thickness is required to limit the loss of tracking precision due to scattering. The reduction of silicon thickness is performed at wafer level in a two-step thinning process. To minimize the risk of wafer breakage the thinned wafer needs to be handled by a carrier during the whole process chain of wafer bumping. Another key process is the flip chip assembly of thinned readout chips onto thin sensor tiles. Besides the prevention of silicon breakage the minimization of chip warpage is one additional task for a high yield and reliable flip chip process. A new technology using glass carrier wafer will be described in detail. The main advantage of this technology is the combination of a carrier support during wafer processing and the chip support during flip chip assembly. For that a glass wafer is glue-bonded onto the backside of the thinned readout chip wafer. After the bump deposition process the glass-readout chip stack is diced in one step. Finally the glass carrier chip is released by laser illumination after flip chip assembly of the readout chip onto sensor tile. The results of the flip chip assembly process development for the ATLAS IBL upgrade are described more in detail. The new ATLAS FEI4B chip with a size of 20 × 19 mm 2 is flip chip bonded with a thickness of only 150 μm, but the capability of this technology has been demonstrated on hybrid modules with a reduced readout chip thickness of down to 50 μm which is a major step for ultra-thin electronic systems

  5. Ash and heavy metals in fluidized-bed combustion of wood wastes; Tuhka ja raskasmetallit puuperaeisen jaetteen kerrosleijupoltossa

    Energy Technology Data Exchange (ETDEWEB)

    Kaessi, T; Aittoniemi, P [IVO Power Engineering, Vantaa (Finland); Kauppinen, E; Latva-Somppi, J; Kurkela, J [VTT Chemical Technology, Espoo (Finland); Partanen, J [IVO Technology Centre, Vantaa (Finland)

    1997-10-01

    Ash formation and deposition mechanisms during co-combustion of pulp mill sludge and bark in industrial bubbling fluidized bed (BFB) combustor have been studied. Similar fuels were used in a bench-scale BFB for co-combustion of sludge and bark pellets and comparative studies with separate combustion of these fuels. Results indicated that in industrial scale unit significant fraction of ash had vaporization. About 14 mass-% of the total fly ash was found in the particle size below 0.2 {mu}m. The vaporized species consisted of potassium (K), sulfur (S), chlorine (Cl) and also of minor quantities of sodium (Na). In the benchscale similar vaporization fractions during co-combustion were measured, about 11 mass-%. During the combustion of bark this ratio, about 20 mass-%, was higher than during sludge combustion. The vaporized ash fraction was in the case of dried sludge combustion about 7 mass-%, but with wet sludge the vaporization rate was remarkably lower, about 1-2 mass-%. An increase in the bed temperature increased also ash vaporization. Test run period without combustion at elevated temperatures produced very low quantities of vaporized ash. The vaporized species in bench-scale test during bark pellet combustion were K, S and Cl, for sludge combustion also Na was clearly detected. No condensation of the vaporized species in bed area or furnace walls was observed. Bed defluidization was studied in the bench-scale unit. During bark pellet combustion the bed-agglomeration proceeded via small ash particle, below 2 {mu}m, coating on sand particle surface and consequent bonding between the ash layers. In the case of sludge combustion the accumulation of large ash particles and sintering of these porous agglomerates was observed to cause bed coarsening and defluidization. (orig.)

  6. Competitive outcomes between wood-decaying fungi are altered in burnt wood.

    Science.gov (United States)

    Edman, Mattias; Eriksson, Anna-Maria

    2016-06-01

    Fire is an important disturbance agent in boreal forests where it creates a wide variety of charred and other types of heat-modified dead wood substrates, yet how these substrates affect fungal community structure and development within wood is poorly understood. We allowed six species of wood-decaying basidiomycetes to compete in pairs in wood-discs that were experimentally burnt before fungal inoculation. The outcomes of interactions in burnt wood differed from those in unburnt control wood for two species:Antrodia sinuosanever lost on burnt wood and won over its competitor in 67% of the trials compared to 40% losses and 20% wins on unburnt wood. In contrast, Ischnoderma benzoinumwon all interactions on unburnt wood compared to 33% on burnt wood. However, the responses differed depending on the identity of the competing species, suggesting an interaction between competitor and substrate type. The observed shift in competitive balance between fungal species probably results from chemical changes in burnt wood, but the underlying mechanism needs further investigation. Nevertheless, the results indicate that forest fires indirectly structure fungal communities by modifying dead wood, and highlight the importance of fire-affected dead wood substrates in boreal forests. © FEMS 2016. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

  7. Operation of a steam hydro-gasifier in a fluidized bed reactor

    OpenAIRE

    Park, Chan Seung; Norbeck, Joseph N.

    2008-01-01

    Carbonaceous material, which can comprise municipal waste, biomass, wood, coal, or a natural or synthetic polymer, is converted to a stream of methane and carbon monoxide rich gas by heating the carbonaceous material in a fluidized bed reactor using hydrogen, as fluidizing medium, and using steam, under reducing conditions at a temperature and pressure sufficient to generate a stream of methane and carbon monoxide rich gas but at a temperature low enough and/or at a pressure high enough to en...

  8. NOx formation and selective non-catalytic reduction (SNCR) in a fluidized bed combustor of biomass

    International Nuclear Information System (INIS)

    Mahmoudi, Shiva; Baeyens, Jan; Seville, Jonathan P.K.

    2010-01-01

    Caledonian Paper (CaPa) is a major paper mill, located in Ayr, Scotland. For its steam supply, it previously relied on the use of a Circulating Fluidized Bed Combustor (CFBC) of 58 MW th , burning coal, wood bark and wastewater treatment sludge. It currently uses a bubbling fluidized bed combustor (BFBC) of 102 MW th to generate steam at 99 bar, superheated to 465 o C. The boiler is followed by steam turbines and a 15 kg/s steam circuit into the mill. Whereas previously coal, wood bark and wastewater treatment sludge were used as fuel, currently only plantation wood (mainly spruce), demolition wood, wood bark and sludge are used. Since these biosolids contain nitrogen, fuel NO x is formed at the combustion temperature of 850-900 o C. NO x emissions (NO + NO 2 ) vary on average between 300 and 600 mg/Nm 3 (dry gas). The current emission standard is 350 mg/Nm 3 but will be reduced in the future to a maximum of 233 mg/Nm 3 for stand-alone biomass combustors of capacity between 50 and 300 MW th according to the EU LCP standards. NO x abatement is therefore necessary. In the present paper we firstly review the NO x formation mechanisms, proving that for applications of fluidized bed combustion, fuel NO x is the main consideration, and the contribution of thermal NO x to the emissions insignificant. We then assess the deNO x techniques presented in the literature, with an updated review and special focus upon the techniques that are applicable at CaPa. From these techniques, Selective Non-catalytic Reduction (SNCR) using ammonia or urea emerges as the most appropriate NO x abatement solution. Although SNCR deNO x is a selective reduction, the reactions of NO x reduction by NH 3 in the presence of oxygen, and the oxidation of NH 3 proceed competitively. Both reactions were therefore studied in a lab-scale reactor and the results were transformed into design equations starting from the respective reaction kinetics. An overall deNO x yield can then be predicted for any

  9. Methodology for choice of harvesting system for energy wood from early thinning

    Energy Technology Data Exchange (ETDEWEB)

    Laitila, J

    2012-11-01

    The primary aim of the present study was to develop a methodology for estimating the procurement cost of forest chips from early thinnings. The most common logging systems and supply chains of forest chips used in early thinnings in Finland were compared at stand and regional level using productivity models and cost parameters obtained mainly from the substudies of this thesis. Furthermore, a decision tree was constructed for selecting harvesting method for energy wood originating from early thinnings. Forwarding productivity following mechanised cutting was significantly higher compared to productivity after motor-manual cutting. Mechanised cutting by the harvester enables felling and bunching of whole trees into large grapple loads close to strip roads, which facilitates increasing forwarding output and reducing costs. The two-machine system comprised of a harvester and a forwarder was the most cost-efficient logging system due to higher efficiency in cutting and especially in the forwarding phase. The cost of motor-manual whole-tree cutting was equal to mechanised whole-tree cutting, while forwarding cost after motor-manual cutting was almost double that after mechanised cutting. Using a forwarderbased harwarder resulted in the highest logging costs. However, with large tree volumes and removals its costs were almost equal to those of motor-manual-based logging. In order to achieve a breakthrough for the harwarder system, costs must be reduced by improving both machine technology and working techniques. Available volumes and procurement costs of fuel chips made of small-diameter trees were compared at regional level. The trees were harvested either by the multi-stem delimbed shortwood or whole-tree method and chipped by a truck-mounted drum chipper at the roadside. Based on the availability analysis, delimbing reduced regional cutting recovery by 42% compared to whole tree harvesting, when the minimum concentration of energy wood was set at 25 m{sup 3} ha{sup -1

  10. Gas and particle concentrations in horse stables with individual boxes as a function of the bedding material and the mucking regimen.

    Science.gov (United States)

    Fleming, K; Hessel, E F; Van den Weghe, H F A

    2009-11-01

    The aim of this study was to compare different types of bedding and mucking regimens used in horse stables on the generation of airborne particulate matter bedding material (wheat straw, straw pellets, and wood shavings) used for horses were assessed according to their ammonia generation. Each type of bedding was used for 2 wk, with 3 repetitions. The mean ammonia concentrations within the stable were 3.07 +/- 0.23 mg/m(3) for wheat straw, 4.79 +/- 0.23 mg/m(3) for straw pellets, and 4.27 +/- 0.17 mg/m(3) for wood shavings. In Exp. 2, the effects of the mucking regimen on the generation of ammonia and PM10 from wheat straw (the bedding with the least ammonia generation in the previous experiment) were examined using 3 different daily regimens: 1) no mucking out, 2) complete mucking out, and 3) partial mucking out (removing only feces). The mean ammonia concentrations in the stable differed significantly among all 3 mucking regimens (P bedding regimen without mucking out was evaluated with regard to gas and airborne particle generation. The ammonia values were found not to increase constantly during the course of the 6-wk period. The average weekly values for PM10 also did not increase constantly but varied between approximately 90 and 140 microg/m. It can be concluded from the particle and gas generation patterns found in the results of all 3 experiments that wheat straw was the most suitable bedding of the 3 types investigated and that mucking out completely on a daily basis should not be undertaken in horse stables.

  11. Biopulping: A new energy-saving technology for papermaking

    International Nuclear Information System (INIS)

    Scott, G.M.; Akhtar, M.; Lentz, M.J.; Kirk, T.K.; Swaney, R.; Shipley, D.F.

    1997-01-01

    Biopulping is defined as the treatment of wood chips with lignin-degrading fungi prior to pulping. Fungal pretreatment prior to mechanical pulping reduces electrical energy requirements during refining or increases mill throughput, improves paper strength, reduces the pitch content, reduces cooking time for sulfite pulping, and reduces the environmental impact of pulping. The recent work involved scaling up the biopulping process towards the industrial level, investigating both the engineering and economic feasibility of the technology. The authors envision the process to be done in either a chip-pile or silo-based system for which several factors need to be considered. These factors include the degree of decontamination, a hospitable environment for the fungus, and the overall process economics. Currently, treatment of the chips with low pressure steam is sufficient for decontamination. Furthermore, a simple, forced ventilation system can be used to maintain the proper temperature, humidity, and moisture content throughout the chip bed, thus promoting uniform growth of the fungus. The pilot-scale trial resulted in the successful treatment of 4 tons, of wood chips (dry weight basis) with results comparable to those on a laboratory scale. For mechanical pulping, a 2-week treatment results in approximately 30% energy savings that, considering the additional equipment and operating costs, results in an overall savings of $9 to $20/ton of pulp in a chip-pile system. The other benefits that biopulping confers improve the economics considerably A larger, 40-ton trial was also successful, with energy savings and paper properties comparable with the laboratory scale

  12. Co-combustion of gasified contaminated waste wood in a coal fired power plant

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-07-01

    This project demonstrates the technical and economical feasibility of the producing and cofiring of product gas from demolition waste wood. For this purpose LCV product gas is generated in an atmospheric circulating fluidized bed (CFB) gasification plant, cooled and cleaned and transported to the boiler of a 600 MWe pulverized coal fired power plant. Gas cooling and cleaning takes place in a waste heat boiler and a multi stage wet gas cleaning train. Steam raised in the waste heat boiler is exported to the power plant. On an annual basis 70,000 tons of steam coal are substituted by 150,000 tons of contaminated demolition waste wood (50,000 tons oil equivalent), resulting in a net CO2 emission reduction of 170,000 tons per year, while concurrently generating 205 GWh of electrical power. The wood gasification plant was built by NV EPZ (now incorporated in Essent Energi BV) for Amergas BV, now a 100% subsidiary of Essent Energie BV. The gasification plant is located at the Amer Power Station of NV EPZ Production (now Essent Generation) at Geertruidenberg, The Netherlands. Demonstrating several important design features in wood gasification, the plant started hot service in the Spring of 2000, with first gasification accomplished in the Summer of 2000 and is currently being optimized. (au)

  13. Influence of humic substances and wood decay products on the valency state of uranium

    International Nuclear Information System (INIS)

    Abraham, A.

    2002-01-01

    The purpose of the present study was to investigate the influence of dissolved natural substances on the oxidation state of iron and uranium. The ongoing remediation of uranium mining areas in Saxony and Thuringia involves flooding of extended pits, submerging and subjecting to microbial decay considerable amounts of pit timber in the process. This gives rise to the problem whether the reductive environment which develops as a result of wood decay in the pit water is capable of reducing the uranium (VI) and iron (III) contained in the flood water. Measurements of the valency state of uranium and iron following their interaction with natural decay products were performed by means of electrochemical, photometric and laser spectroscopic methods. This was followed by sorption experiments with a view to collecting phenomenological data on the binding behaviour of uranium species with respect to the rock bed of the Western Erz Hills and the sediments of the Elbe valley under different redox potential conditions. The study was concluded with redox potential calculations aimed at describing the state of pit waters as well as characterising analogous natural waters. The study was performed using humic acids for alkaline brown coal extract, high moor humic substances originating from natural microbial wood decay for wood decay products, and products from hydrothermal wood decomposition as well as lignin for a methanolic wood extract [de

  14. Fluidized bed catalytic pyrolysis of eucalyptus over hzsm-5: effect of acid density and gallium modification on catalyst deactivation

    Science.gov (United States)

    Catalytic fast pyrolysis of eucalyptus wood was performed on a continuous laboratory scale fluidized bed fast pyrolysis system. Catalytic activity was monitored from use of fresh catalyst up to a cumulative biomass to catalyst ratio (B/C) of 4/1 over extruded pellets of three different ZSM-5 catalys...

  15. Potential wood protection strategies using physiological requirements of wood degrading fungi

    NARCIS (Netherlands)

    Sailer, M.F.; Etten, B.D. van

    2004-01-01

    Due to the increasing restrictions in the use of wood preserving biocides a number of potential biocide free wood preserving alternatives are currently assessed. Wood degrading fungi require certain conditions in the wood in order to be able to use wood as a food source. This paper discusses the

  16. Mathematic modulation of a simulation program for a coal and wood counter-current moving bed gasifier, which includes pyrolysis and drying processes and processes alternatives; Modelagem matematica e simulacao em computador de gaseificador de leito fixo contra-corrente para carvoes e biomassa com inclusao de processos de pirolise, secagem e alternativas do processo

    Energy Technology Data Exchange (ETDEWEB)

    Souza Santos, M.L. de [Instituto de Pesquisas Tecnologicas (IPT), Sao Paulo, SP (Brazil)

    1985-12-31

    A new version of a simulation program for coal and wood counter-current fixed bed gasifier has been completed and provides: all the principal information variables of the process throughout the bed as mass flow and composition for 13 gases and 6 solids, temperature of the gas and solid phases, reaction rates of combustion, gasification, pyrolysis and drying processes; composition, mass flow, temperature, combustion enthalpy and other produced gases physical and chemical properties; possibility of process alternatives analysis as volatiles recycling in order to eliminate tar, double withdrawn of gases and combinations. Comparisons between simulation and experimental results are presented. (author). 26 refs., 1 tab

  17. Kraft cooking of gamma irradiated wood, (2)

    International Nuclear Information System (INIS)

    Inaba, Masamitsu; Meshitsuka, Gyosuke; Ishizu, Atsushi; Nakano, Junzo

    1981-01-01

    Pre-irradiation of wood in alkaline aqueous ethanol increases kraft pulp yield by up to 1.2%, as already reported. In order to clarify the mechanism of the pulp yield gain, the behaviors of lignin and carbohydrates during pre-irradiation and cooking were investigated. The results are summarized as follows: 1) γ-Irradiation of guaiacylethane in alkaline aqueous ethanol produced 5-(1-hydroxyethyl)-guaicylethane, which is formed by radical coupling between α-hydroxyethyl radical from ethanol and guaiacylethane radical having an unpaired electron at C-5. 5,5'-Dehydrodiguaiacylethane, which may be a predominant product produced by γ-irradiation in the absence of ethanol, was also detected. 2) The yield of vanillin obtained by nitrobenzene oxidation of MWL decreased with an increase of γ-ray dosage. The presence of ethanol during γ-irradiation lessened the extent of this decrease and also the degradation of cellobiose. 3) Gel filtration of the products obtained by γ-irradiation of MWL and cellobiose in the presence of 14 C-ethanol showed the possible combination between ethanol and MWL or cellobiose. 4) Molecular weight distributions of kraft lignin obtained from pre-irradiated beech chips were compared with those obtained from unirradiated chips. This result shows that γ-irradiation in the presence of ethanol decreases the ability of lignin to condense during kraft cooking. (author)

  18. Nutrient removal capacity of wood residues for the Agro-environmental safety of ground and surface waters

    Directory of Open Access Journals (Sweden)

    Paulo A. Dumont

    2014-07-01

    Full Text Available The aim of this study was to determine the effectiveness of wood residues in the removal of nutrients (ammonium-N; NH4-N from nutrient-rich (NH4-N waters. The water holding capacity of the wood materials was also determined. Carried out at Rothamsted Research, North Wyke, UK, this controlled laboratory experiment tested two wood residues; in length, one being 1-2cm and the other from 150 µm (microns to 9.5mm. Although a wide range of studies have shown the effectiveness and performance of various absorbent materials as animal beddings, such as straw (cereal straw, woodchip (sawdust, bark or wood shavings, bracken and rushes, only few have focused on the NH4-N sorption/desorption capacity. The depuration capacity of wood residues from nutrient-rich effluents such as those from cattle bedded on woodchip or straw will be controlled by processes such as sorption (adsorption-absorption and desorption of nutrients. Studies have reported the nitrogen removal capacity of woodchip materials and biochar from woodchip as well as removal of NH4+-N from domestic and municipal wastewater, farm dirty water, landfill and industry effluents. These studies have observed that the mechanism of removal of nitrogen is by either increasing NO3--N removal form leachate by enhancing N2O losses via denitrification (biochar as carbon source for denitrifiers or by decreasing NH4+-N in leachate through adsorption to negatively charged sites. Results showed that although the cation exchange capacity (CEC and surface area (SA are both fundamental properties of adsorbent materials, no correlation was found with CEC and adsorption or desorption. Nor did changes in pH appear to be sufficiently important to cause changes in CEC. For this reason, osmotic pressure appeared to be a more predominant parameter controlling processes of adsorption and desorption of NH4+-N in both wood residues. Thus, wood residues high in NH4+-N should be avoided, as they could have an opposite effect

  19. Guide for construction of wood power systems. Construction - economic efficiency - technology; Leitfaden fuer die Errichtung von Holzenergie-Anlagen. Umsetzung - Wirtschaftlichkeit - Technologie

    Energy Technology Data Exchange (ETDEWEB)

    Ruchser, M. [Forum fuer Zukunftsenergien e.V., Bonn (Germany)

    2001-07-01

    The Guidebook serves as a handbook for the entire operational sequence, which is necessary for the establishment of a wood combustion plant in Germany with an installed capacity larger than 100 kW{sub th}, for the use of fuel woods such as forest chips, wood and forest residues, pellets, wood waste, etc. within the limits of the laws and regulations prescribed for the respective performance classes. The Guidebook's purpose is to give potential investors and operators of wood combustion plants as well as the appropriate authorities a quick and global overview of the energetic use of wood in order to contribute to an increased application of this technology. The Guidebook introduces a Quality Model in Chapters 2 and 3, which describes the establishment of a wood combustion system in six phases. Eleven Management Aspects are differentiated, which can be helpful during the conversion of a project. Thus, potential investors and operators of wood combustion plants become acquainted with the most important aspects of this kind of project conversion. In addition, Chapter 4 provides an overview of the operating costs of wood combustion plants. The relevant licensing and planning procedures depending on the installed capacity and fuelwood use are comprehensively described in Chapter 5. Chapter 6 supplies a concrete overview of the environmental aspects and emissions of wood combustion. Since wood combustion plants must be - as all other investments - financially secured Chapter 7 provides a description of the relevant information on public means and subsidies. Besides all important promotion programmes, the new German Renewable Energy Law (Erneuerbare-Energien-Gesetz - EEG) of April 2000 is described in detail. Many examples of already realised wood combustion plant projects are described in Chapter 8. As an additional service, all significant addresses from ministries to energy agencies and associations are listed in Chapter 9. (orig.)

  20. Pitchblende deposits at the Wood and Calhoun mines, Central City mining district, Gilpin County, Colorado

    Science.gov (United States)

    Moore, Frank R.; Butler, C.R.

    1952-01-01

    Pitchblende has been mined in commercial quantities from four gold- and silver-bearing pyrite-sphalerite-galena veins that occur in an area about one-half mile square on the south side of Quartz Hill, Central City district, Gilpin County, Colo. These veins are the Kirk, the German-Belcher, the Wood, and the Calhoun. Two of these veins, the Wood and the Calhoun, were studied in an attempt to determine the geologic factors favorable for pitchblende deposition. All accessible workings at the Wood and East Calhoun mines were mapped by tape and compass, and the distribution of radioactivity was studied in the field. Channel and chip samples were taken for chemical assay to compare radioactivity with uranium content. The pitchblende-bearing veins cat both pre-Cambrian granite gneiss and quartz-biotite schist; however, the gneiss was the more favorable host rock. Two bostonite porphyry dikes of Tertiary(?) age were crosscut by the Wood and Calhoun veins. The pitchblende occurs in lenses erratically distributed along the veins and in stringers extending outward from the veins. In the lenses it forms hard'. masses, but elsewhere it is Soft and powdery. The pitchblende is contemporaneous with the pyrite bat earlier than the sphalerite and galena in the same vein. All the observed pitchblende was at depths of less than 400 ft. The veins probably cannot be mined profitably for the pitchblende alone under present conditions.

  1. Wood Identification of 18th Century Furniture. Interpreting Wood Naming Inventoires

    Directory of Open Access Journals (Sweden)

    Rocio Astrid BERNAL

    2011-09-01

    Full Text Available The 18th century Portuguese church furniture represents an extraordinary richness recognised worldwide, which demands safeguarding and valorisation. The identification of the wood of furniture artworks is the most important component for its comprehension and preservation. In this work wood anatomical characters of an 18th century Portuguese decorative furniture set from the Colegiada de São Martinho de Cedofeita, in Porto, were analysed to identify the woods used for manufacturing and to clarify their common names. Furthermore, the objectives were to recognise some of the criteria for choice of wood as well as the source of each wood. The woods identified from 16 fragments belong to Apuleia sp., Acacia sp., Neolamarckia sp. and Castanea sativa. Apuleia sp. and Acacia sp. woods most likely arrived from Brazil, while the Neolamarckia sp. woods likely arrived from India and the C. sativa woods from Portugal. The results are in accordance with the known Portuguese colonial sea routes of the 15th -18th centuries. Interestingly the terms found in the inventories can refer to finishing methods instead to the name of the woods, as for instance “oil wood” can refer to “oiled wood” or “linseed oiled wood”. The species choice may be related to the mechanical properties of the wood as well as the original tree size. Two large planks of Acacia sp. were used for the top of the “Portuguese arcaz”, and Apuleia sp. was found on main structural elements of this set of furniture, suggesting that wood colour was also important. Woods from Neolamarckia sp. and C. sativa, were also identified, being Castanea wood present only in the most recent pieces of the furniture set.

  2. Demonstration of the efficiency and robustness of an acid leaching process to remove metals from various CCA-treated wood samples.

    Science.gov (United States)

    Coudert, Lucie; Blais, Jean-François; Mercier, Guy; Cooper, Paul; Janin, Amélie; Gastonguay, Louis

    2014-01-01

    In recent years, an efficient and economically attractive leaching process has been developed to remove metals from copper-based treated wood wastes. This study explored the applicability of this leaching process using chromated copper arsenate (CCA) treated wood samples with different initial metal loading and elapsed time between wood preservation treatment and remediation. The sulfuric acid leaching process resulted in the solubilization of more than 87% of the As, 70% of the Cr, and 76% of the Cu from CCA-chips and in the solubilization of more than 96% of the As, 78% of the Cr and 91% of the Cu from CCA-sawdust. The results showed that the performance of this leaching process might be influenced by the initial metal loading of the treated wood wastes and the elapsed time between preservation treatment and remediation. The effluents generated during the leaching steps were treated by precipitation-coagulation to satisfy the regulations for effluent discharge in municipal sewers. Precipitation using ferric chloride and sodium hydroxide was highly efficient, removing more than 99% of the As, Cr, and Cu. It appears that this leaching process can be successfully applied to remove metals from different CCA-treated wood samples and then from the effluents. Copyright © 2013 Elsevier Ltd. All rights reserved.

  3. Wood-related occupations, wood dust exposure, and sinonasal cancer.

    Science.gov (United States)

    Hayes, R B; Gerin, M; Raatgever, J W; de Bruyn, A

    1986-10-01

    A case-control study was conducted to examine the relations between type of woodworking and the extent of wood dust exposure to the risks for specific histologic types of sinonasal cancer. In cooperation with the major treatment centers in the Netherlands, 116 male patients newly diagnosed between 1978 and 1981 with primary malignancies of epithelial origin of this site were identified for study. Living controls were selected from the municipal registries, and deceased controls were selected from the national death registry. Interviews were completed for 91 (78%) cases and 195 (75%) controls. Job histories were coded by industry and occupation. An index of exposure was developed to classify the extent of occupational exposure to wood dust. When necessary, adjustment was made for age and usual cigarette use. The risk for nasal adenocarcinoma was elevated by industry for the wood and paper industry (odds ratio (OR) = 11.9) and by occupation for those employed in furniture and cabinet making (OR = 139.8), in factory joinery and carpentry work (OR = 16.3), and in association with high-level wood dust exposure (OR = 26.3). Other types of nasal cancer were not found to be associated with wood-related industries or occupations. A moderate excess in risk for squamous cell cancer (OR = 2.5) was associated with low-level wood dust exposure; however, no dose-response relation was evident. The association between wood dust and adenocarcinoma was strongest for those employed in wood dust-related occupations between 1930 and 1941. The risk of adenocarcinoma did not appear to decrease for at least 15 years after termination of exposure to wood dust. No cases of nasal adenocarcinoma were observed in men whose first exposure to wood dust occurred after 1941.

  4. Comparative analysis of wood chips and bundles - Costs, carbon dioxide emissions, dry-matter losses and allergic reactions

    Energy Technology Data Exchange (ETDEWEB)

    Eriksson, Lisa; Gustavsson, Leif [Ecotechnology, Department of Engineering and Sustainable Development, Mid Sweden University, SE-831 25 Oestersund (Sweden)

    2010-01-15

    There are multiple systems for the collection, processing, and transport of forest residues for use as a fuel. We compare two systems in use in Sweden to analyze differences in fuel cost, CO{sub 2} emissions, dry-matter loss, and potential for allergic reactions. We compare a bundle system with the traditional Swedish chip system, and then do an in-depth comparison of a Finnish bundle system with the Swedish bundle system. Bundle systems have lower costs, while the allergic reactions do not differ significantly between the systems. The bundle machine is expensive, but results in high productivity and in an overall cost-effective system. The bundle system has higher primary energy use and CO{sub 2} emissions, but the lower dry-matter losses in the bundle system chain give CO{sub 2} emissions per delivered MWh almost as low as for the chip system. Also, lower dry-matter losses mean that more biomass per hectare can be extracted from the clear-cut area. This leads to a higher possible substitution of fossil fuels per hectare with the bundle system, and that more CO{sub 2} emissions from fossil fuel can be avoided per hectare than in the chip system. The Finnish bundle system with its more effective compressing and forwarding is more cost- and energy-effective than the Swedish bundle system, but Swedish bundle systems can be adapted to be more effective in both aspects. (author)

  5. Effect of cement/wood ratios and wood storage conditions on hydration temperature, hydration time, and compressive strength of wood-cement mixtures

    Science.gov (United States)

    Andy W.C. Lee; Zhongli Hong; Douglas R. Phillips; Chung-Yun Hse

    1987-01-01

    This study investigated the effect of cement/wood ratios and wood storage conditions on hydration temperature, hydration time, and compressive strength of wood-cement mixtures made from six wood species: southern pine, white oak, southern red oak, yellow-poplar, sweetgum, and hickory. Cement/wood ratios varied from 13/1 to 4/1. Wood storage conditions consisted of air-...

  6. Catalytic flash pyrolysis of oil-impregnated-wood and jatropha cake using sodium based catalysts

    KAUST Repository

    Imran, Ali

    2015-11-24

    Catalytic pyrolysis of wood with impregnated vegetable oil was investigated and compared with catalytic pyrolysis of jatropha cake making use of sodium based catalysts to produce a high quality bio-oil. The catalytic pyrolysis was carried out in two modes: in-situ catalytic pyrolysis and post treatment of the pyrolysis vapors. The in-situ catalytic pyrolysis was carried out in an entrained flow reactor system using a premixed feedstock of Na2CO3 and biomass and post treatment of biomass pyrolysis vapor was conducted in a downstream fixed bed reactor of Na2CO3/γ-Al2O3. Results have shown that both Na2CO3 and Na2CO3/γ-Al2O3 can be used for the production of a high quality bio-oil from catalytic pyrolysis of oil-impregnated-wood and jatropha cake. The catalytic bio-oil had very low oxygen content, water content as low as 1wt.%, a neutral pH, and a high calorific value upto 41.8MJ/kg. The bio-oil consisted of high value chemical compounds mainly hydrocarbons and undesired compounds in the bio-oil were either completely removed or considerably reduced. Increasing the triglycerides content (vegetable oil) in the wood enhanced the formation of hydrocarbons in the bio-oil. Post treatment of the pyrolysis vapor over a fixed bed of Na2CO3/γ-Al2O3 produced superior quality bio-oil compared to in-situ catalytic pyrolysis with Na2CO3. This high quality bio-oil may be used as a precursor in a fractionating process for the production of alternative fuels. © 2015 Elsevier B.V.

  7. INTENSIFICATION OF HEAT TRANSFER IN A HIGH-TEMPERATURED FLUIDIZED BED

    Directory of Open Access Journals (Sweden)

    А. O. Redko

    2017-10-01

    Full Text Available Purpose. This paper highlights experimental research of heat exchange in coarse particles to ensure the performance of ecological characteristics of Heat supply system. Methodology. The test stand has been developed to solve the defined task. It helps to do the research at the temperature of fluidizing bed and pulsating fluidizing bed at the range 800–1000°С. The temperature of the fluidized bed was provided by burning natural gas and wood waste. Sand and chamotte with a particle size of 1.0 to 5.0 mm were used as the layer material. The heat-transfer coefficient from the layer to the surface, immersed in the layer, and the density of the heat flux were measured by a calorimetric method under steady-state conditions. Smooth tubes and transversely finned with different height and rib spacing were investigated. Experiments in a high-temperature pulsating fluidized bed were carried out with pulsating combustion of natural gas in a layer or in a sublattice chamber into which natural gas and air were separately supplied. The frequency of combustion pulsations was provided by the automation system. The flash frequency was regulated in the range from 0.14 to 5 Hz. Findings. It is presented the results of physical modeling to find out the heat-transfer coefficients of smooth and finned tubes in fluidizing bed of coarse particles in the process of wood waste and gaseous fuel combusting. It is proved that the coefficient of heat transfer increases with increasing temperature by 2–2,5 times in the bed which contains particles diameter of 2.5–5 mm is 300–350Vt/(m2 К that is much higher than for layer furnaces. The results of the experiments are presented in the form of a generalized relationship that takes into account the diameter of the particles and the value of the finning coefficient. Heat transfer of finned tubes is 15–20% less then smooth tubes but the density of heat flow referred to the area of a finned tube is 0,12–0,20 МVt/m2 that

  8. Wood pellet seminar

    International Nuclear Information System (INIS)

    Aarniala, M.; Puhakka, A.

    2001-01-01

    The objective of the wood pellet seminar, arranged by OPET Finland and North Karelia Polytechnic, was to deliver information on wood pellets, pellet burners and boilers, heating systems and building, as well as on the activities of wood energy advisors. The first day of the seminar consisted of presentations of equipment and products, and of advisory desks for builders. The second day of the seminar consisted of presentations held by wood pellet experts. Pellet markets, the economy and production, the development of the pellet markets and their problems (in Austria), the economy of heating of real estates by different fuel alternatives, the production, delivery and marketing of wood pellets, the utilization of wood pellet in different utilization sites, the use of wood pellets in detached houses, pellet burners and fireplaces, and conversion of communal real estate houses to use wood pellets were discussed in the presentations. The presentations held in the third day discussed the utilization of wood pellets in power plants, the regional promotion of the production and the use of pellets. The seminar consisted also of visits to pellet manufacturing plant and two pellet burning heating plants

  9. Projected wood energy impact on US forest wood resources

    Energy Technology Data Exchange (ETDEWEB)

    Skog, K.E. [USDA Forest Service, Madison, WI (United States)

    1993-12-31

    The USDA Forest Service has developed long-term projections of wood energy use as part of a 1993 assessment of demand for and supply of resources from forest and range lands in the United States. To assess the impact of wood energy demand on timber resources, a market equilibrium model based on linear programming was developed to project residential, industrial, commercial, and utility wood energy use from various wood energy sources: roundwood from various land sources, primary wood products mill residue, other wood residue, and black liquor. Baseline projections are driven by projected price of fossil fuels compared to price of wood fuels and the projected increase in total energy use in various end uses. Wood energy use is projected to increase from 2.67 quad in 1986 to 3.5 quad in 2030 and 3.7 quad in 2040. This is less than the DOE National Energy Strategy projection of 5.5 quad in 2030. Wood energy from forest sources (roundwood) is projected to increase from 3.1 billion (10{sup 9}) ft{sup 3} in 1986 to 4.4. billion ft{sup 3} in 2030 and 4.8 billion ft{sup 3} in 2040 (88, 124 and 136 million m{sup 3}, respectively). This rate of increase of roundwood use for fuel -- 0.8 percent per year -- is virtually the same as the projected increase rate for roundwood for pulpwood. Pulpwood roundwood is projected to increase from 4.2 billion ft{sup 3} in 1986 to 6.0 billion ft{sup 3} in 2030 and 6.4 billion ft{sup 3} in 2040 (119, 170 and 183 million m{sup 3}, respectively).

  10. Flip chip assembly of thinned chips for hybrid pixel detector applications

    CERN Document Server

    Fritzsch, T; Woehrmann, M; Rothermund, M; Huegging, F; Ehrmann, O; Oppermann, H; Lang, K.D

    2014-01-01

    There is a steady trend to ultra-thin microelectronic devices. Especially for future particle detector systems a reduced readout chip thickness is required to limit the loss of tracking precision due to scattering. The reduction of silicon thickness is performed at wafer level in a two-step thinning process. To minimize the risk of wafer breakage the thinned wafer needs to be handled by a carrier during the whole process chain of wafer bumping. Another key process is the flip chip assembly of thinned readout chips onto thin sensor tiles. Besides the prevention of silicon breakage the minimization of chip warpage is one additional task for a high yield and reliable flip chip process. A new technology using glass carrier wafer will be described in detail. The main advantage of this technology is the combination of a carrier support during wafer processing and the chip support during flip chip assembly. For that a glass wafer is glue-bonded onto the backside of the thinned readout chip wafer. After the bump depo...

  11. Accelerated Aging of the Traditional Greek Distillate Tsipouro Using Wooden Chips. Part I: Effect of Static Maceration vs. Ultrasonication on the Polyphenol Extraction and Antioxidant Activity

    Directory of Open Access Journals (Sweden)

    Theodora Taloumi

    2017-01-01

    Full Text Available The Greek traditional grape marc distillate Tsipouro was subjected to accelerated aging, using wooden chips from acacia, cherry, chestnut and oak wood. The processes included treatments under static maceration and ultrasonication and the evolution of the total polyphenol concentration was monitored over a period of 30 days. During this period, leaching of polyphenols from the chips into the distillate was found to obey first-order kinetics, but no statistical differences were shown between the two treatments regarding the enrichment of the liquid in polyphenolic substances. The determination of the antioxidant activity demonstrated that aging with chestnut chips may provide Tsipouro with particularly strong radical scavenging and reducing effects, highlighting its importance as a material that could be used to turn distillates into foods with functional properties.

  12. Modelling piloted ignition of wood and plastics

    International Nuclear Information System (INIS)

    Blijderveen, Maarten van; Bramer, Eddy A.; Brem, Gerrit

    2012-01-01

    Highlights: ► We model piloted ignition times of wood and plastics. ► The model is applied on a packed bed. ► When the air flow is above a critical level, no ignition can take place. - Abstract: To gain insight in the startup of an incinerator, this article deals with piloted ignition. A newly developed model is described to predict the piloted ignition times of wood, PMMA and PVC. The model is based on the lower flammability limit and the adiabatic flame temperature at this limit. The incoming radiative heat flux, sample thickness and moisture content are some of the used variables. Not only the ignition time can be calculated with the model, but also the mass flux and surface temperature at ignition. The ignition times for softwoods and PMMA are mainly under-predicted. For hardwoods and PVC the predicted ignition times agree well with experimental results. Due to a significant scatter in the experimental data the mass flux and surface temperature calculated with the model are hard to validate. The model is applied on the startup of a municipal waste incineration plant. For this process a maximum allowable primary air flow is derived. When the primary air flow is above this maximum air flow, no ignition can be obtained.

  13. Evaluating the effects of bedding materials and elevated platforms on contact dermatitis and plumage cleanliness of commercial broilers and on litter condition in broiler houses.

    Science.gov (United States)

    Kaukonen, E; Norring, M; Valros, A

    2017-10-01

    1. Experiment 1, comparing wood shavings and ground straw bedding with peat, was performed on 7 broiler farms over two consecutive batches during the winter season. Experiment 2, assessing the effect of elevated (30 cm) platforms, was conducted in three farms replicated with 6 consecutive batches. 2. Footpad lesions were inspected at slaughter following the Welfare Quality® (WQ) assessment and official programme. Hock lesions, plumage cleanliness and litter condition were assessed using the WQ assessment. Litter height, pH, moisture and ammonia were determined. 3. Footpad condition on wood shavings appeared to be worse compared with peat using both methods of assessment and was accompanied by inferior hock skin health. WQ assessment resulted in poorer footpad and hock skin condition on ground straw compared with peat. Farms differed in footpad and hock skin condition. Footpad and hock lesions were not affected by platform treatment. Peat appeared more friable than ground straw. The initial pH of wood shavings was higher and moisture was lower than in peat, but at the end of production period there were no differences. Ground straw exhibited higher initial and lower end pH, and was drier in the beginning than peat. Litter condition and quality were not affected by platform treatment. 4. This study provides new knowledge about the applicability of peat as broiler bedding and shows no negative effects of elevated platforms on litter condition or the occurrence of contact dermatitis in commercial environments. The results suggest a complicated relationship between litter condition, moisture and contact dermatitis. Furthermore, it is concluded that the farmer's ability to manage litter conditions is important, regardless of the chosen litter material. Peat bedding was beneficial for footpad and hock skin health compared with wood shavings and ground straw.

  14. 2000-2006 National Wood Energy Programme. 2000-2005 Activities Report

    International Nuclear Information System (INIS)

    2006-01-01

    component in developing wood energy. In this context, wood energy will be a key part of the fight against climate change and the development of renewable sources of energy. This report presents: 1 - the Wood Energy issues, advantages and key figures, and the evaluation of resources; 2 - The 2000-2006 Programme: objectives (domestic heating, industrial heating systems, urban, public and tertiary heating), operation (ADEME programme leadership (2000-2005), partnerships and State Region planning contracts, the funding system for Wood Energy projects (2000-2005, modified in November 2004 and the other financial instruments (FOGIME/FIDEME); 3 - 2000-2005 Assessment: results by sector (domestic wood-fired heating, industrial, public and tertiary sectors); supply development and structuring (supply systems and regional diversity, growth in suppliers, supply structuring, emergence of new players in the market, biomass resources and forestry work, developing the use of wood chips, the impact of collecting slash); Information and communication (leadership and promotion, publications supported by ADEME); Appendixes: fuels and energy content, detailed report, studies funded by ADEME; ADEME's presentation; 2005 R and D projects

  15. On-chip concentration of bacteria using a 3D dielectrophoretic chip and subsequent laser-based DNA extraction in the same chip

    International Nuclear Information System (INIS)

    Cho, Yoon-Kyoung; Kim, Tae-hyeong; Lee, Jeong-Gun

    2010-01-01

    We report the on-chip concentration of bacteria using a dielectrophoretic (DEP) chip with 3D electrodes and subsequent laser-based DNA extraction in the same chip. The DEP chip has a set of interdigitated Au post electrodes with 50 µm height to generate a network of non-uniform electric fields for the efficient trapping by DEP. The metal post array was fabricated by photolithography and subsequent Ni and Au electroplating. Three model bacteria samples (Escherichia coli, Staphylococcus epidermidis, Streptococcus mutans) were tested and over 80-fold concentrations were achieved within 2 min. Subsequently, on-chip DNA extraction from the concentrated bacteria in the 3D DEP chip was performed by laser irradiation using the laser-irradiated magnetic bead system (LIMBS) in the same chip. The extracted DNA was analyzed with silicon chip-based real-time polymerase chain reaction (PCR). The total process of on-chip bacteria concentration and the subsequent DNA extraction can be completed within 10 min including the manual operation time.

  16. Finishing of wood

    Science.gov (United States)

    R. Sam Williams

    1999-01-01

    The primary function of any wood finish (paint, varnish, and stain, for example) is to protect the wood surface, help maintain a certain appearance, and provide a cleanable surface. Although wood can be used both outdoors and indoors without finishing, unfinished wood surfaces exposed to the weather change color, are roughened by photodegradation and surface checking,...

  17. Wood fuels utilization in Central Europe - the wood fuels consumption and the targets of utilization

    International Nuclear Information System (INIS)

    Alakangas, E.

    1999-01-01

    Following subjects are discussed in this presentation: The share of bioenergy of the total energy consumption in EU region; the wood fuels consumption in EU region in 1995; the division of bioenergy utilization (households, wood- based district heating, wood consumption in industry, power generation from wood and residues, biofuels, biogas and sludges); wood fuels consumption in households in EU countries in 1995; wood consumption in France; the additional wood fuel consumption potential in France; Blan bois - wood energy program; French wood energy markets; German wood energy markets; energy consumption in Germany; wood consumption in Bavaria; the wood fuels potential in Bavaria; wood fuels consumption in households in Bavaria; wood fuels consumption for district heating in Bavaria; fuel prices in Bavaria; Environmental regulations in Germany; small boiler markets in Germany; Energy consumption in Austria; small-scale utilization of wood fuels; utilization of wood energy. (Slides, additional information from the author)

  18. Wood construction and magnetic characteristics of impregnated type magnetic wood

    International Nuclear Information System (INIS)

    Oka, Hideo; Hojo, Atsushi; Seki, Kyoushiro; Takashiba, Toshio

    2002-01-01

    The results of experiments involving the AC and DC magnetic characteristics of impregnated type magnetic wood were studied by taking into consideration the wood construction and fiber direction. The experimental results show that the sufficient amount of impregnated magnetic fluid varies depending on the fiber direction and length, and the grain face of the wood material. The impregnated type magnetic wood sample that is fully impregnated by magnetic fluid has a 60% saturation magnetization compared to the saturation magnetization of magnetic fluid. Samples for which the wood fiber direction was the same as the direction of the magnetic path had a higher magnetization intensity and permeability

  19. Production of fungal volatile organic compounds in bedding materials

    Directory of Open Access Journals (Sweden)

    S. LAPPALAINEN

    2008-12-01

    Full Text Available The high relative humidity of the air and many potential growth media, such as bedding materials, hay and grains in the horse stable, for example, provide suitable conditions for fungal growth. Metabolic activity of four common agricultural fungi incubated in peat and wood shavings at 25°C and 4°C was characterized in this study using previously specified volatile metabolites of micro-organisms and CO 2 production as indicators. The volatile organic compounds were collected into Tenax resin and analysed by gas chromatography. Several microbial volatile organic compounds (MVOCs, e.g. 1-butanol, 2-hexanone, 2-heptanone, 3-octanone, 1-octen-3-ol and 1-octanol were detected in laboratory experiments; however, these accounted for only 0.08-1.5% of total volatile organic com-pounds (TVOCs. Emission rates of MVOCs were 0.001-0.176 mg/kg of bedding materials per hour. Despite some limitations of the analytical method, certain individual MVOCs, 2-hexanone, 2-hep-tanone and 3-octanone, were also detected in concentrations of less than 4.6 mg/m 3 (0.07-0.31% of TVOC in a horse stable where peat and shavings were used as bedding materials. MVOC emission rate was estimated to be 0.2-2.0 mg/kg ´ h -1 from bedding materials in the stable, being about ten times higher than the rates found in the laboratory experiments. Some compounds, e.g. 3-octanone and 1-octen-3-ol, can be assumed to originate mainly from microbial metabolisms.;

  20. Wood preservatives and pressure-treated wood: considerations for historic-preservation projects

    Science.gov (United States)

    Ronald W. Anthony; Stan T. Lebow

    2015-01-01

    Wood, an abundant resource throughout most of the world, has been used as a building material for thousands of years. Many historic buildings have been built primarily of wood, and masonry and stone buildings generally have wood elements, both structural and architectural. As a biological material, wood is both remarkably complex and yet quite durable if well...

  1. Chips 2020

    CERN Document Server

    2016-01-01

    The release of this second volume of CHIPS 2020 coincides with the 50th anniversary of Moore’s Law, a critical year marked by the end of the nanometer roadmap and by a significantly reduced annual rise in chip performance. At the same time, we are witnessing a data explosion in the Internet, which is consuming 40% more electrical power every year, leading to fears of a major blackout of the Internet by 2020. The messages of the first CHIPS 2020, published in 2012, concerned the realization of quantum steps for improving the energy efficiency of all chip functions. With this second volume, we review these messages and amplify upon the most promising directions: ultra-low-voltage electronics, nanoscale monolithic 3D integration, relevant-data, brain- and human-vision-inspired processing, and energy harvesting for chip autonomy. The team of authors, enlarged by more world leaders in low-power, monolithic 3D, video, and Silicon brains, presents new vistas in nanoelectronics, promising  Moore-like exponential g...

  2. Release of Inorganic Elements during Wood Combustion. Release to the Gas Phase of Inorganic Elements during: Wood Combustion. Part 1: Development and Evaluation of Quantification Methods

    DEFF Research Database (Denmark)

    van Lith, Simone Cornelia; Alonso-Ramírez, Violeta; Jensen, Peter Arendt

    2006-01-01

    During wood combustion, inorganic elements such as alkali metals, sulfur, chlorine, and some heavy metals are partly released to the gas phase, which may cause problems in combustion facilities because of deposit formation and corrosion. Furthermore, it may cause harmful emissions of gases......) in this reactor, whereas methods B and C involved initial pyrolysis and combustion, respectively, of a large fuel sample (~5 kg) in a bench-scale fixed-bed reactor at 500 C. The methods were evaluated by comparing the data on the release of Cl, S, K, Na, Zn, and Pb from fiber board obtained by the three methods...

  3. Integrated control of wood destroying basidiomycetes combining Cu-based wood preservatives and Trichoderma spp.

    Science.gov (United States)

    Ribera, Javier; Fink, Siegfried; Bas, Maria Del Carmen; Schwarze, Francis W M R

    2017-01-01

    The production of new generation of wood preservatives (without addition of a co-biocide) in combination with an exchange of wood poles on identical sites with high fungal inoculum, has resulted in an increase of premature failures of wood utility poles in the last decades. Wood destroying basidiomycetes inhabiting sites where poles have been installed, have developed resistance against wood preservatives. The objective of the in vitro studies was to identify a Trichoderma spp. with a highly antagonistic potential against wood destroying basidiomycetes that is capable of colonizing Cu-rich environments. For this purpose, the activity of five Trichoderma spp. on Cu-rich medium was evaluated according to its growth and sporulation rates. The influence of the selected Trichoderma spp. on wood colonization and degradation by five wood destroying basidiomycetes was quantitatively analyzed by means of dry weight loss of wood specimens. Furthermore, the preventative effect of the selected Trichoderma spp. in combination with four Cu-based preservatives was also examined by mass loss and histological changes in the wood specimens. Trichoderma harzianum (T-720) was considered the biocontrol agent with higher antagonistic potential to colonize Cu-rich environments (up to 0.1% CuSO4 amended medium). T. harzianum demonstrated significant preventative effect on wood specimens against four wood destroying basidiomycetes. The combined effect of T. harzianum and Cu-based wood preservatives demonstrated that after 9 months incubation with two wood destroying basidiomycetes, wood specimens treated with 3.8 kg m-3 copper-chromium had weight losses between 55-65%, whereas containers previously treated with T. harzianum had significantly lower weight losses (0-25%). Histological studies on one of the wood destroying basidiomycetes revealed typical decomposition of wood cells by brown-rot fungi in Cu-impregnated samples, that were notably absent in wood specimens previously exposed to T

  4. Integrated control of wood destroying basidiomycetes combining Cu-based wood preservatives and Trichoderma spp.

    Directory of Open Access Journals (Sweden)

    Javier Ribera

    Full Text Available The production of new generation of wood preservatives (without addition of a co-biocide in combination with an exchange of wood poles on identical sites with high fungal inoculum, has resulted in an increase of premature failures of wood utility poles in the last decades. Wood destroying basidiomycetes inhabiting sites where poles have been installed, have developed resistance against wood preservatives. The objective of the in vitro studies was to identify a Trichoderma spp. with a highly antagonistic potential against wood destroying basidiomycetes that is capable of colonizing Cu-rich environments. For this purpose, the activity of five Trichoderma spp. on Cu-rich medium was evaluated according to its growth and sporulation rates. The influence of the selected Trichoderma spp. on wood colonization and degradation by five wood destroying basidiomycetes was quantitatively analyzed by means of dry weight loss of wood specimens. Furthermore, the preventative effect of the selected Trichoderma spp. in combination with four Cu-based preservatives was also examined by mass loss and histological changes in the wood specimens. Trichoderma harzianum (T-720 was considered the biocontrol agent with higher antagonistic potential to colonize Cu-rich environments (up to 0.1% CuSO4 amended medium. T. harzianum demonstrated significant preventative effect on wood specimens against four wood destroying basidiomycetes. The combined effect of T. harzianum and Cu-based wood preservatives demonstrated that after 9 months incubation with two wood destroying basidiomycetes, wood specimens treated with 3.8 kg m-3 copper-chromium had weight losses between 55-65%, whereas containers previously treated with T. harzianum had significantly lower weight losses (0-25%. Histological studies on one of the wood destroying basidiomycetes revealed typical decomposition of wood cells by brown-rot fungi in Cu-impregnated samples, that were notably absent in wood specimens

  5. Wood composites

    Science.gov (United States)

    Lars Berglund; Roger M. Rowell

    2005-01-01

    A composite can be defined as two or more elements held together by a matrix. By this definition, what we call “solid wood” is a composite. Solid wood is a three-dimensional composite composed of cellulose, hemicelluloses and lignin (with smaller amounts of inorganics and extractives), held together by a lignin matrix. The advantages of developing wood composites are (...

  6. Bacteria in decomposing wood and their interactions with wood-decay fungi.

    Science.gov (United States)

    Johnston, Sarah R; Boddy, Lynne; Weightman, Andrew J

    2016-11-01

    The fungal community within dead wood has received considerable study, but far less attention has been paid to bacteria in the same habitat. Bacteria have long been known to inhabit decomposing wood, but much remains underexplored about their identity and ecology. Bacteria within the dead wood environment must interact with wood-decay fungi, but again, very little is known about the form this takes; there are indications of both antagonistic and beneficial interactions within this fungal microbiome. Fungi are hypothesised to play an important role in shaping bacterial communities in wood, and conversely, bacteria may affect wood-decay fungi in a variety of ways. This minireview considers what is currently known about bacteria in wood and their interactions with fungi, and proposes possible associations based on examples from other habitats. It aims to identify key knowledge gaps and pressing questions for future research. © FEMS 2016. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

  7. Processing of whole-wood to fuel and raw material; Kokopuun kaesittely polttoaineeksi ja raaka-aineeksi

    Energy Technology Data Exchange (ETDEWEB)

    Aho, V J [VTT Energy, Jyvaeskylae (Finland). Biofuels

    1997-12-01

    The forest industry`s need of wood has increased remarkably during this decade, and will probably continue to increase also during the next few years due to the realisation of the extension investments of the production. Mechanising of whole-tree and tree- section harvesting, development of the lorry transportation of whole-trees and tree-sections, and the improvement of the yield and the quality of pulp-chip fraction produced using integrated harvesting methods are important development targets for the production methods research. The objective of this project is to develop research equipment, by which it is possible to study the unit processes of wood processing, and to develop new wood processing concepts, by which whole-trees could be used for fuel and forest industrial raw material purposes optimally, by combining the unit processes. The research equipment will be of full scale so that it will enable the processing of whole-trees, whole-tree bundles, felling residues and stem-wood fragments. The research equipment consists of versatile measuring and data collection equipment, enabling the processing and analysis of research data. A compactor has been developed in the project, and the development of debarking and feeding units has been started. Additionally, a crushing equipment serving the needs of the research projects of VTT Energy`s research programme `Solid fuel processing technology` has been constructed in the project. The data collection system and the high- speed camera have been acquired to VTT Energy to be used for the measuring equipment

  8. Non_standard Wood

    DEFF Research Database (Denmark)

    Tamke, Martin

    . Using parametric design tools and computer controlled production facilities Copenhagens Centre for IT and Architecture undertook a practice based research into performance based non-standard element design and mass customization techniques. In close cooperation with wood construction software......, but the integration of traditional wood craft techniques. The extensive use of self adjusting, load bearing wood-wood joints contributed to ease in production and assembly of a performance based architecture....

  9. Thermal Properties of Wood-Plastic Composites Prepared from Hemicellulose-extracted Wood Flour

    Directory of Open Access Journals (Sweden)

    A.A. Enayati

    2013-01-01

    Full Text Available Hemicellulose of Southern Yellow Pine wood spices was extracted by pressurized hot water at three different temperatures: 140°C, 155°C and 170°C. Compounding with PP (polypropylene was performed by extrusion after preparing wood flour and sieving to determine its mesh size. The ratio of wood to polymer was 50:50 based on oven-dry weight of wood flour. All extraction treatments and control samples were compounded under two sets of conditions, without and with 2% MAPP as coupling agent. Injection molding was used to make tensile test samples (dogbone from the pellets made by extrusion. Thermal properties of wood-plastic composites were studied by TGA and DSC while the thermal stability of pretreated wood flours, PP and MAPP were studied by TGA as well. The greater weight loss of wood materials was an indication that higher treatment temperature increases the extractability of hemicellulose. The removal of hemicellulose by extraction improves thermal stability of wood flour, especially for extraction at 170°C. Wood-plastic composites made from extracted fibers at 170°C showed the highest thermal stability. Coupling agent did not have a significant effect on thermal stability but it improved the degree of crystallinity of the composites.Surface roughness of wood fiber increased after treatment. Extraction of hemicellulose increased the degree of crystallinity but it was not significant except for samples from treated wood flour at 170°C and with MAPP.

  10. How the user can influence particulate emissions from residential wood and pellet stoves: Emission factors for different fuels and burning conditions

    Science.gov (United States)

    Fachinger, Friederike; Drewnick, Frank; Gieré, Reto; Borrmann, Stephan

    2017-06-01

    For a common household wood stove and a pellet stove we investigated the dependence of emission factors for various gaseous and particulate pollutants on burning phase, burning condition, and fuel. Ideal and non-ideal burning conditions (dried wood, under- and overload, small logs, logs with bark, excess air) were used. We tested 11 hardwood species (apple, ash, bangkirai, birch, beech, cherry, hickory, oak, olive, plum, sugar maple), 4 softwood species (Douglas fir, pine, spruce, spruce/fir), treated softwood, beech and oak wood briquettes, paper briquettes, brown coal, wood chips, and herbaceous species (miscanthus, Chinese silver grass) as fuel. Particle composition (black carbon, non-refractory, and some semi-refractory species) was measured continuously. Repeatability was shown to be better for the pellet stove than for the wood stove. It was shown that the user has a strong influence on wood stove emission behavior both by selection of the fuel and of the burning conditions: Combustion efficiency was found to be low at both very low and very high burn rates, and influenced particle properties such as particle number, mass, and organic content in a complex way. No marked differences were found for the emissions from different wood species. For non-woody fuels, much higher emission factors could be observed (up to five-fold increase). Strongest enhancement of emission factors was found for burning of small or dried logs (up to six-fold), and usage of excess air (two- to three-fold). Real world pellet stove emissions can be expected to be much closer to laboratory-derived emission factors than wood stove emissions, due to lower dependence on user operation.

  11. Technical and economical optimization of wood gasification in a circulating fluidized bed. Final report; Technische und wirtschaftliche Optimierung der Vergasung von Holz in der zirkulierenden Wirbelschicht. Abschlussbericht

    Energy Technology Data Exchange (ETDEWEB)

    Ising, M.; Unger, C.; Heunemann, F.; Dinkelbach, L.

    2002-12-01

    The project's objective was the optimization of a novel process for high efficient combined heat and power production from solid biomass. The processed air blown wood gasification in a pilot scale circulating fluidized bed was added by a catalytic tar reformer which would yield a tar-free gas quality suitable for IC-engine operation. Major efforts were taken for technical improvement of the tar reformer, especially concerning temperature control and cleaning devices which is important for keeping constantly a high activity. Pure natural timber did not yield chemical deactivation at the catalyst whereas the gasification of waste wood yielded decreasing activity which could be partly reversed by special measures taken. Further optimization of the process considered a better automation and improvement of the engine's flue gas emissions. Also a detailed economic consideration and evaluation of the entire process has been carried out. As a result the novel process should have economic advantages compared with conventional technology. (orig.) [German] Gegenstand des Vorhabens war die Weiterentwicklung eines Verfahrens zur effizienteren Strom- und Waermegewinnung aus festen Biobrennstoffen. Durch luftgeblasene Vergasung von Holz im Pilotmassstab in einer zirkulierenden Wirbelschicht und anschliessender katalytischer Teerspaltung konnte ein niederkalorisches Brenngas erzeugt werden, welches zum Betrieb eines Motoren-Blockheizkraftwerks geeignet war. Im Rahmen der Verfahrensoptimierung wurde der katalytische Teer-Reformer, insbesondere in Bezug auf Temperaturfuehrung und die zum Aktivitaetserhalt wichtige Abreinigungsvorrichtung, verbessert. Bei der Vergasung von Naturholz wurde keine chemische Desaktivierung festgestellt. Beim Altholzeinsatz wurde ein ueberwiegend reversibler Aktivitaetsverlust verzeichnet und begruendet. Geeignete Gegenmassnahmen wurden untersucht und beschrieben. Weitere Optimierungen betrafen die Anlagensteuerungstechnik im Hinblick auf die

  12. Attraction of Cerambycid Beetles to Their Aggregation-Sex Pheromones Is Influenced by Volatiles From Host Plants of Their Larvae.

    Science.gov (United States)

    Wong, J C H; Zou, Y; Millar, J G; Hanks, L M

    2017-06-01

    Here, we describe a field experiment that tested for attraction of cerambycid beetles to odors from angiosperm hosts, and whether plant volatiles also serve to enhance attraction of beetles to their aggregation-sex pheromones. Traps were baited with a blend of synthesized chemicals that are common pheromone components of species in the subfamilies Cerambycinae and Lamiinae. The source of plant volatiles was chipped wood from trees of three angiosperm species, as well as from one nonhost, gymnosperm species. Bioassays were conducted in wooded areas of east-central Illinois. Traps were baited with the pheromone blend alone, the blend + wood chips from one tree species, wood chips alone, or a solvent control lure. Seven species of cerambycids were significantly attracted to the pheromone blend, with or without wood chips. In two cases, wood chips from angiosperms appeared to enhance attraction to pheromones, whereas they inhibited attraction in another three cases. Pine chips did not strongly influence attraction of any species. Overall, our results suggest that host plant volatiles from wood chips may improve trap catch with synthesized pheromones for some cerambycid species, but the effect is not general, necessitating case-by-case testing to determine how individual target species are affected. © The Authors 2017. Published by Oxford University Press on behalf of Entomological Society of America. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

  13. Lignin-Retaining Transparent Wood.

    Science.gov (United States)

    Li, Yuanyuan; Fu, Qiliang; Rojas, Ramiro; Yan, Min; Lawoko, Martin; Berglund, Lars

    2017-09-11

    Optically transparent wood, combining optical and mechanical performance, is an emerging new material for light-transmitting structures in buildings with the aim of reducing energy consumption. One of the main obstacles for transparent wood fabrication is delignification, where around 30 wt % of wood tissue is removed to reduce light absorption and refractive index mismatch. This step is time consuming and not environmentally benign. Moreover, lignin removal weakens the wood structure, limiting the fabrication of large structures. A green and industrially feasible method has now been developed to prepare transparent wood. Up to 80 wt % of lignin is preserved, leading to a stronger wood template compared to the delignified alternative. After polymer infiltration, a high-lignin-content transparent wood with transmittance of 83 %, haze of 75 %, thermal conductivity of 0.23 W mK -1 , and work-tofracture of 1.2 MJ m -3 (a magnitude higher than glass) was obtained. This transparent wood preparation method is efficient and applicable to various wood species. The transparent wood obtained shows potential for application in energy-saving buildings. © 2017 The Authors. Published by Wiley-VCH Verlag GmbH & Co. KGaA.

  14. Mountain forest wood fuel supply chains: comparative studies between Norway and Italy

    International Nuclear Information System (INIS)

    Valente, Clara; Spinelli, Raffaele; Hillring, Bengt Gunnar; Solberg, Birger

    2014-01-01

    Case studies of mountain forest wood fuel supply chains from Norway and Italy are presented and compared. Results from previous studies in which greenhouse gas emissions and costs were evaluated using life cycle assessment and cost analysis respectively, are compared. The supply chain is more mechanized in Norway than Italy. Steeper terrain and low road density partly explain the persistence of motor-manual felling in the Italian case. Mechanized forest harvesting can increase productivity and reduce costs, but generates more greenhouse gas (GHG) emissions than motor-manual harvesting. In both cases, the main sources of GHG emissions are truck transportation and chipping. The total emissions are 22.9 kg CO 2 /m 3 s.o.b. (Norway) and 13.2 kg CO 2 /m 3 s.o.b. (Italy). The Norwegian case has higher costs than the Italian one, 64 €/m 3 s.o.b. and 41 €/m 3 s.o.b. respectively, for the overall supply chain. The study shows that mountain forests constitute an interesting source for fuel biomass in both areas, but are a rather costly source, particularly in Norway. The study also exemplifies the care needed in transferring LCA results between regions and countries, particularly where forest biomass is involved. - Highlights: • We compare two mountain forest wood fuel supply chains in Norway and in Italy. • Transportation by truck generate the highest emissions in both case studies. • The energy use of the Norwegian supply chain was approximately twice as high as the Italian one. • Changes in fuel consumption affect significantly emissions and energy use from transportation and chipping operations. • Cable yarding and transportation by truck were the most expensive phases respectively in the Italian and Norwegian supply chain

  15. Using multiple bed load measurements: Toward the identification of bed dilation and contraction in gravel-bed rivers

    Science.gov (United States)

    Marquis, G. A.; Roy, A. G.

    2012-02-01

    This study examines bed load transport processes in a small gravel-bed river (Béard Creek, Québec) using three complementary methods: bed elevation changes between successive floods, bed activity surveys using tags inserted into the bed, and bed load transport rates from bed load traps. The analysis of 20 flood events capable of mobilizing bed material led to the identification of divergent results among the methods. In particular, bed elevation changes were not consistent with the bed activity surveys. In many cases, bed elevation changes were significant (1 to 2 times the D50) even if the bed surface had not been activated during the flood, leading to the identification of processes of bed dilation and contraction that occurred over 10% to 40% of the bed surface. These dynamics of the river bed prevent accurate derivation of bed load transport rates from topographic changes, especially for low magnitude floods. This paper discusses the mechanisms that could explain the dilation and contraction of particles within the bed and their implications in fluvial dynamics. Bed contraction seems to be the result of the winnowing of the fine sediments under very low gravel transport. Bed dilation seems to occur on patches of the bed at the threshold of motion where various processes such as fine sediment infiltration lead to the maintenance of a larger sediment framework volume. Both processes are also influenced by flood history and the initial local bed state and in turn may have a significant impact on sediment transport and morphological changes in gravel-bed rivers.

  16. Mechanics of Wood Machining

    CERN Document Server

    Csanády, Etele

    2013-01-01

    Wood is one of the most valuable materials for mankind, and since our earliest days wood materials have been widely used. Today we have modern woodworking machine and tools; however, the raw wood materials available are continuously declining. Therefore we are forced to use this precious material more economically, reducing waste wherever possible. This new textbook on the “Mechanics of Wood Machining” combines the quantitative, mathematical analysis of the mechanisms of wood processing with practical recommendations and solutions. Bringing together materials from many sources, the book contains new theoretical and experimental approaches and offers a clear and systematic overview of the theory of wood cutting, thermal loading in wood-cutting tools, dynamic behaviour of tool and work piece, optimum choice of operational parameters and energy consumption, the wear process of the tools, and the general regularities of wood surface roughness. Diagrams are provided for the quick estimation of various process ...

  17. Effects of short-term repeated exposure to different flooring surfaces on the behavior and physiology of dairy cattle.

    Science.gov (United States)

    Schütz, K E; Cox, N R

    2014-05-01

    Dairy cattle managed in some pasture-based systems such as in New Zealand are predominantly kept outdoors all year around, but are often taken off pasture for periods of time in wet weather to avoid soil damage. It is common to keep cattle on concrete surfaces during such "stand-off" practices and we investigated whether the addition of rubber matting onto concrete areas improves the welfare of dairy cattle. Sixteen groups of 5 cows (4 groups/treatment, 5 cows/group) were allocated to 1 of 4 treatments (concrete, 12-mm-thick rubber mat, 24-mm-thick rubber mat, or deep-bedded wood chips) and kept on these surfaces for 18 h/24h for 4 consecutive days (6h on pasture/24h). Each 4-d stand-off period was repeated 4 times (with 7 d of recovery between periods) to study the accumulated effects of repeated stand-off. Lying behavior was recorded continuously during the experiment. Gait score, stride length, hygiene score, live weight, and blood samples for cortisol analysis were recorded immediately before and after each stand-off period. Cows on wood chips spent the most time lying, and cows on concrete spent the least time lying compared with those on other surfaces [wood chips: 10.8h, 24-mm rubber mat: 7.3h, 12-mm rubber mat: 6.0 h, and concrete: 2.8h/18 h, standard error of the difference (SED): 0.71 h]. Cows on concrete spent more time lying during the 6h on pasture, likely compensating for the reduced lying during the stand-off period. Similarly, cows on concrete spent more time lying on pasture between stand-off periods (concrete: 12.1h, 12-mm rubber mat: 11.1h, 24-mm rubber mat: 11.2h, and wood chips: 10.7h/24h, SED: 0.28 h). Cows on concrete had higher gait score and shorter stride length after the 4-d stand-off period compared with cows on the other surface types, suggesting a change in gait pattern caused by discomfort. Cows on rubber mats were almost 3 times dirtier than cows on concrete or wood chips. Cortisol and live weight decreased for all treatment groups

  18. Soil-wood interactions

    NARCIS (Netherlands)

    Wal, van der Annemieke; klein Gunnewiek, Paulien; Boer, de Wietse

    2017-01-01

    Wood-inhabiting fungi may affect soil fungal communities directly underneath decaying wood via their exploratory hyphae. In addition, differences in wood leachates between decaying tree species may influence soil fungal communities. We determined the composition of fungi in 4-yr old decaying logs

  19. STUDY OF CHIP IGNITION AND CHIP MORPHOLOGY AFTER MILLING OF MAGNESIUM ALLOYS

    Directory of Open Access Journals (Sweden)

    Ireneusz Zagórski

    2016-12-01

    Full Text Available The paper analyses the impact of specified technological parameters of milling (vc, fz, ap on time to ignition. Stages leading to chip ignition were analysed. Metallographic images of magnesium chip were presented. No significant difference was observed in time to ignition in different chip fractions. Moreover, the surface of chips was free of products of ignition and signs of strong oxidation.

  20. The Advances, Challenges and Future Possibilities of Millimeter-Wave Chip-to-Chip Interconnections for Multi-Chip Systems

    Directory of Open Access Journals (Sweden)

    Amlan Ganguly

    2018-02-01

    Full Text Available With aggressive scaling of device geometries, density of manufacturing faults is expected to increase. Therefore, yield of complex Multi-Processor Systems-on-Chips (MP-SoCs will decrease due to higher probability of manufacturing defects especially, in dies with large area. Therefore, disintegration of large SoCs into smaller chips called chiplets will improve yield and cost of complex platform-based systems. This will also provide functional flexibility, modular scalability as well as the capability to integrate heterogeneous architectures and technologies in a single unit. However, with scaling of the number of chiplets in such a system, the shared resources in the system such as the interconnection fabric and memory modules will become performance bottlenecks. Additionally, the integration of heterogeneous chiplets operating at different frequencies and voltages can be challenging. State-of-the-art inter-chip communication requires power-hungry high-speed I/O circuits and data transfer over long wired traces on substrates. This increases energy consumption and latency while decreasing data bandwidth for chip-to-chip communication. In this paper, we explore the advances and the challenges of interconnecting a multi-chip system with millimeter-wave (mm-wave wireless interconnects from a variety of perspectives spanning multiple aspects of the wireless interconnection design. Our discussion on the recent advances include aspects such as interconnection topology, physical layer, Medium Access Control (MAC and routing protocols. We also present some potential paradigm-shifting applications as well as complementary technologies of wireless inter-chip communications.

  1. Wood energy-commercial applications

    Science.gov (United States)

    Kennel, R. P.

    1978-01-01

    Wood energy is being widely investigated in many areas of the country because of the many obvious benefits of wood fuel such as the low price per million Btus relative to coal, oil, and gas; the wide availability of noncommercial wood and the proven ability to harvest it; established technology which is reliable and free of pollution; renewable resources; better conservation for harvested land; and the potential for jobs creation. The Southeastern United States has a specific leadership role in wood energy based on its established forest products industry experience and the potential application of wood energy to other industries and institutions. Significant questions about the widespread usage of wood energy are being answered in demonstrations around the country as well as the Southeast in areas of wood storage and bulk handling; high capitalization costs for harvesting and combustion equipment; long term supply and demand contracts; and the economic feasibility of wood energy outside the forest products industry.

  2. Who's Counting Dead Wood ?

    OpenAIRE

    Woodall, C. W.; Verkerk, H.; Rondeux, Jacques; Ståhl, G.

    2009-01-01

    Dead wood in forests is a critical component of biodiversity, carbon and nutrient cycles, stand structure, and fuel loadings. Until recently, very few countries have conducted systematic inventories of dead wood resources across their forest lands. This may be changing as an increasing number of countries implement dead wood inventories. A recent survey looks at the status and attributes of forest dead wood inventories in over 60 countries. About 13 percent of countries inventory dead wood gl...

  3. Occurrence patterns of dead wood and wood-dependent lichens in managed boreal forest landscapes

    OpenAIRE

    Svensson, Måns

    2013-01-01

    Dead wood is a key resource for biodiversity, on which thousands of forest organisms are dependent. Because of current forest management, there has been a large-scale change in dead wood amounts and qualities, and consequently, many wood-dependent species are threatened. The general aim of this thesis is to increase our understanding of habitat requirements and occurrence patterns of wood-dependent lichens in managed, boreal forest landscapes. We surveyed dead wood and wood-dependent lichens ...

  4. Establishment of ectomycorrhizal fungal community on isolated Nothofagus cunninghamii seedlings regenerating on dead wood in Australian wet temperate forests: does fruit-body type matter?

    Science.gov (United States)

    Tedersoo, Leho; Gates, Genevieve; Dunk, Chris W; Lebel, Teresa; May, Tom W; Kõljalg, Urmas; Jairus, Teele

    2009-08-01

    Decaying wood provides an important habitat for animals and forms a seed bed for many shade-intolerant, small-seeded plants, particularly Nothofagus. Using morphotyping and rDNA sequence analysis, we compared the ectomycorrhizal fungal community of isolated N. cunninghamii seedlings regenerating in decayed wood against that of mature tree roots in the forest floor soil. The /cortinarius, /russula-lactarius, and /laccaria were the most species-rich and abundant lineages in forest floor soil in Australian sites at Yarra, Victoria and Warra, Tasmania. On root tips of seedlings in dead wood, a subset of the forest floor taxa were prevalent among them species of /laccaria, /tomentella-thelephora, and /descolea, but other forest floor dominants were rare. Statistical analyses suggested that the fungal community differs between forest floor soil and dead wood at the level of both species and phylogenetic lineage. The fungal species colonizing isolated seedlings on decayed wood in austral forests were taxonomically dissimilar to the species dominating in similar habitats in Europe. We conclude that formation of a resupinate fruit body type on the underside of decayed wood is not necessarily related to preferential root colonization in decayed wood. Rather, biogeographic factors as well as differential dispersal and competitive abilities of fungal taxa are likely to play a key role in structuring the ectomycorrhizal fungal community on isolated seedlings in decaying wood.

  5. Flash pyrolysis, a process for utilizing contaminated wood; Flash-Pyrolyse - eine Moeglichkeit der stofflichen Verwertung von kontaminiertem Holz

    Energy Technology Data Exchange (ETDEWEB)

    Meier, D; Wehlte, S; Faix, O [Bundesforschungsanstalt fuer Forst- und Holzwirtschaft, Hamburg (Germany). Inst. fuer Holzchemie und Chemische Technologie des Holzes

    1997-12-31

    Flash pyrolysis of wood treated with common pesticides poses no technical probelms. Product yields, with a maximum oil yield at 475 C, are similar to those of untreated wood. Most of the heavy metals are retained by the coal while a small part aheres to the coal layer of the sand bed. The resulting pyrolysis oil contains neither chromium nor copper. (orig) [Deutsch] Die Flash-Pyrolyse der mit den gaengigsten Schutzmitteln behandelten Hoelzer bereitet verfahrenstechnisch keine Probleme. Auch die Produktausbeuten, mit einem oelmaximum bei 475 C, aehneln denen von naturbelassenem Holz. Der groesste Teil der Schwermetalle wurde an die Kohle gebunden, ein geringer Teil blieb auf der Kohleschicht des Sandes haften. Im Hauptprodukt Pyrolyseoel konnten weder Chrom noch Kupfer nachgewiesen werden. (orig)

  6. Flash pyrolysis, a process for utilizing contaminated wood; Flash-Pyrolyse - eine Moeglichkeit der stofflichen Verwertung von kontaminiertem Holz

    Energy Technology Data Exchange (ETDEWEB)

    Meier, D.; Wehlte, S.; Faix, O. [Bundesforschungsanstalt fuer Forst- und Holzwirtschaft, Hamburg (Germany). Inst. fuer Holzchemie und Chemische Technologie des Holzes

    1996-12-31

    Flash pyrolysis of wood treated with common pesticides poses no technical probelms. Product yields, with a maximum oil yield at 475 C, are similar to those of untreated wood. Most of the heavy metals are retained by the coal while a small part aheres to the coal layer of the sand bed. The resulting pyrolysis oil contains neither chromium nor copper. (orig) [Deutsch] Die Flash-Pyrolyse der mit den gaengigsten Schutzmitteln behandelten Hoelzer bereitet verfahrenstechnisch keine Probleme. Auch die Produktausbeuten, mit einem oelmaximum bei 475 C, aehneln denen von naturbelassenem Holz. Der groesste Teil der Schwermetalle wurde an die Kohle gebunden, ein geringer Teil blieb auf der Kohleschicht des Sandes haften. Im Hauptprodukt Pyrolyseoel konnten weder Chrom noch Kupfer nachgewiesen werden. (orig)

  7. Wood preservative testing

    Science.gov (United States)

    Rebecca Ibach; Stan T. Lebow

    2012-01-01

    Most wood species used in commercial and residential construction have little natural biological durability and will suffer from biodeterioration when exposed to moisture. Historically, this problem has been overcome by treating wood for outdoor use with toxic wood preservatives. As societal acceptance of chemical use changes, there is continual pressure to develop and...

  8. Wood Dust

    Science.gov (United States)

    Learn about wood dust, which can raise the risk of cancers of the paranasal sinuses and nasal cavity. High amounts of wood dust are produced in sawmills, and in the furniture-making, cabinet-making, and carpentry industries.

  9. Wood Smoke

    Science.gov (United States)

    Smoke is made up of a complex mixture of gases and fine, microscopic particles produced when wood and other organic matter burn. The biggest health threat from wood smoke comes from fine particles (also called particulate matter).

  10. Energy wood harvesting from nurse crop of spruce seeding stand; Kuusen taimikon verhopuuston korjuu energiapuuksi

    Energy Technology Data Exchange (ETDEWEB)

    Peltola, M.; Tanttu, V.

    2008-07-01

    The study focused on establishing the productivity and costs of mechanical energy wood cutting and the profitability of forest management alternatives in the harvesting of hold-overs from spruce seeding stands. The productivity in whole-tree harvesting performed using a multi-tree whole tree processing method reached 3.5 m3/E{sub 0}h with a felling cost of 26 euros/m3. The calculated cost of chainsaw harvesting using a felling-piling technique was 16 euros/m3. The average size of trees harvested from the research stand was 15 dm3. At a rate of 17.8 euros per megawatt that was paid for forest chips delivered to the plant, the net profit using mechanical harvesting method was 272 euros per hectare. The net profit using chainsaw harvesting was 464 euros per hectare. 'Net profit' is defined here as the total amount earned, taking into account forest management costs, the production cost of forest chips, the Kemera subsidies and the price paid for the chips at the place of usage. The net profit of felling the removed trees to the ground (not processing it into fuel) was minus 124 euros. A theoretical stumpage price rate was calculated for the energy harvesting alternatives by dividing the net result by the volume of trees harvested. Theoretical stumpage price was positive when the paid price per megawatt of chips delivered to the place of usage was 13 euros per megawatt-hour for mechanically harvested chips or 10 euros per megawatt-hour for chainsaw-harvested chips. In mechanical harvesting, 17 percent of the trees harvested were damaged in the harvesting process. While it is often essential for the forest owner to ensure that any forest management measures contribute to quick profitability, the forest management benefits that will become realisable assets in the future must nevertheless also be taken into account. (orig.)

  11. Effects of Operating Conditions and Dusty Fuel on the NOx, N2O and CO Emissions in PFB Co-Combustion of Coal and Wood

    Czech Academy of Sciences Publication Activity Database

    Svoboda, Karel; Pohořelý, Michael; Hartman, Miloslav

    2003-01-01

    Roč. 17, č. 4 (2003), s. 1091-1099 ISSN 0887-0624 R&D Projects: GA AV ČR IAA4072801 Institutional research plan: CEZ:AV0Z4072921 Keywords : pressurized fluidized bed * co-combustion * wood Subject RIV: JE - Non-nuclear Energetics, Energy Consumption ; Use Impact factor: 1.303, year: 2003

  12. Chip-to-Chip Half Duplex Spiking Data Communication over Power Supply Rails

    Science.gov (United States)

    Hashida, Takushi; Nagata, Makoto

    Chip-to-chip serial data communication is superposed on power supply over common Vdd/Vss connections through chip, package, and board traces. A power line transceiver demonstrates half duplex spiking communication at more than 100Mbps. A pair of transceivers consumes 1.35mA from 3.3V, at 130Mbps. On-chip power line LC low pass filter attenuates pseudo-differential communication spikes by 30dB, purifying power supply current for internal circuits. Bi-directional spiking communication was successfully examined in a 90-nm CMOS prototype setup of on-chip waveform capturing. A micro controller forwards clock pulses to and receives data streams from a comparator based waveform capturer formed on a different chip, through a single pair of power and ground traces. The bit error rate is small enough not to degrade waveform acquisition capability, maintaining the spurious free dynamic range of higher than 50dB.

  13. Relative performance of three stream bed stability indices as indicators of stream health.

    Science.gov (United States)

    Kusnierz, Paul C; Holbrook, Christopher M

    2017-10-16

    Bed stability is an important stream habitat attribute because it affects geomorphology and biotic communities. Natural resource managers desire indices of bed stability that can be used under a wide range of geomorphic conditions, are biologically meaningful, and are easily incorporated into sampling protocols. To eliminate potential bias due to presence of instream wood and increase precision of stability values, we modified a stream bed instability index (ISI) to include measurements of bankfull depth (d bf ) and median particle diameter (D 50 ) only in riffles and increased the pebble count to decrease variability (i.e., increase precision) in D 50 . The new riffle-based instability index (RISI) was compared to two established indices: ISI and the riffle stability index (RSI). RISI and ISI were strongly associated with each other but neither was closely associated with RSI. RISI and ISI were closely associated with both a diatom- and two macrovertebrate-based stream health indices, but RSI was only weakly associated with the macroinvertebrate indices. Unexpectedly, precision of D 50 did not differ between RISI and ISI. Results suggest that RISI is a viable alternative to both ISI and RSI for evaluating bed stability in multiple stream types. With few data requirements and a simple protocol, RISI may also better conform to riffle-based sampling methods used by some water quality practitioners.

  14. Combustion of impregnated wood. Test combustion in a biofuel boiler at Orrefors; Foerbraenning av impregnerat virke. Testfoerbraenning i en biobraenslepanna, Orrefors

    Energy Technology Data Exchange (ETDEWEB)

    Bergman, Goeran; Erlandsson, Martin; Hemstroem, Kristian; Hoegberg, Bengt; Oesterberg, Helen

    2010-10-15

    It is possible to burn impregnated wood containing copper in a biofuel boiler if the boiler has suitable flue gas cleaning equipment. The studied facility needs to complete its flue gas treatment with a dust control step (such as electrostatic precipitator, fabric or bag filter). If the incineration surpasses 50 tonnes of waste per year a special permission is required. Smaller quantities requires only a notification. In combustion of wood chips with an admixture of up to 20% copper-impregnated wood (50% sapwood and 50% kernel) the bottom ash stands clear of all minimum and maximum levels according to the Forestry Board's recommendations for using the ash as a fertilizer in forestry. The findings from the ash leaching tests show that chromium leaching from bottom ash of samples 4 and 5 is too high to allow deposition of the ashes in landfills along with non-hazardous wastes (the rest of the ash passed all the benchmarks). A hazard analysis has been carried out where the concept of toxicity index (TI) has been applied

  15. Analysis on Storage Off-Gas Emissions from Woody, Herbaceous, and Torrefied Biomass

    Directory of Open Access Journals (Sweden)

    Jaya Shankar Tumuluru

    2015-03-01

    Full Text Available Wood chips, torrefied wood chips, ground switchgrass, and wood pellets were tested for off‑gas emissions during storage. Storage canisters with gas‑collection ports were used to conduct experiments at room temperature of 20 °C and in a laboratory oven set at 40 °C. Commercially-produced wood pellets yielded the highest carbon monoxide (CO emissions at both 20 and 40 °C (1600 and 13,000 ppmv, whereas torrefied wood chips emitted the lowest of about <200 and <2000 ppmv. Carbon dioxide (CO2 emissions from wood pellets were 3000 ppmv and 42,000 ppmv, whereas torrefied wood chips registered at about 2000 and 25,000 ppmv, at 20 and 40 °C at the end of 11 days of storage. CO emission factors (milligrams per kilogram of biomass calculated were lowest for ground switchgrass and torrefied wood chips (2.68 and 4.86 mg/kg whereas wood pellets had the highest CO of about 10.60 mg/kg, respectively, at 40 °C after 11 days of storage. In the case of CO2, wood pellets recorded the lowest value of 55.46 mg/kg, whereas switchgrass recorded the highest value of 318.72 mg/kg. This study concludes that CO emission factor is highest for wood pellets, CO2 is highest for switchgrass and CH4 is negligible for all feedstocks except for wood pellets, which is about 0.374 mg/kg at the end of 11-day storage at 40 °C.

  16. Technological and life cycle assessment of organics processing odour control technologies

    Energy Technology Data Exchange (ETDEWEB)

    Bindra, Navin [School of Engineering, University of Guelph, 50 Stone Road East, Guelph, Ontario N1G2W1 (Canada); Dubey, Brajesh, E-mail: bkdubey@civil.iitkgp.ernet.in [School of Engineering, University of Guelph, 50 Stone Road East, Guelph, Ontario N1G2W1 (Canada); Environmental Engineering Division, Department of Civil Engineering, Indian Institute of Technology, Kharagpur, West Bengal 721302 (India); Dutta, Animesh [School of Engineering, University of Guelph, 50 Stone Road East, Guelph, Ontario N1G2W1 (Canada)

    2015-09-15

    As more municipalities and communities across developed world look towards implementing organic waste management programmes or upgrading existing ones, composting facilities are emerging as a popular choice. However, odour from these facilities continues to be one of the most important concerns in terms of cost & effective mitigation. This paper provides a technological and life cycle assessment of some of the different odour control technologies and treatment methods that can be implemented in organics processing facilities. The technological assessment compared biofilters, packed tower wet scrubbers, fine mist wet scrubbers, activated carbon adsorption, thermal oxidization, oxidization chemicals and masking agents. The technologies/treatment methods were evaluated and compared based on a variety of operational, usage and cost parameters. Based on the technological assessment it was found that, biofilters and packed bed wet scrubbers are the most applicable odour control technologies for use in organics processing faculties. A life cycle assessment was then done to compare the environmental impacts of the packed-bed wet scrubber system, organic (wood-chip media) bio-filter and inorganic (synthetic media) bio-filter systems. Twelve impact categories were assessed; cumulative energy demand (CED), climate change, human toxicity, photochemical oxidant formation, metal depletion, fossil depletion, terrestrial acidification, freshwater eutrophication, marine eutrophication, terrestrial eco-toxicity, freshwater eco-toxicity and marine eco-toxicity. The results showed that for all impact categories the synthetic media biofilter had the highest environmental impact, followed by the wood chip media bio-filter system. The packed-bed system had the lowest environmental impact for all categories. - Highlights: • Assessment of odour control technologies for organics processing facilities. • Comparative life cycle assessment of three odour control technologies was conducted

  17. Wood thermoplastic composites

    Science.gov (United States)

    Daniel F. Caulfield; Craig Clemons; Roger M. Rowell

    2010-01-01

    The wood industry can expand into new sustainable markets with the formation of a new class of composites with the marriage of the wood industry and the plastics industry. The wood component, usually a flour or fiber, is combined with a thermoplastic to form an extrudable, injectable or thermoformable composite that can be used in many non-structural applications....

  18. Fluidized-bed gasification of biomass: Conversion of fine carabon particles in the freeboard; Biomassevergasung in der Wirbelschicht: Umsatz von feinen Kohlenstoffpartikeln im Freeboard

    Energy Technology Data Exchange (ETDEWEB)

    Miccio, F [Ist. Ricerche sulla Combustione-CNR, Napoli (Italy); Moersch, O; Spliethoff, H; Hein, K R.G. [Stuttgart Univ. (Germany). Inst. fuer Verfahrenstechnik und Dampfkesselwesen

    1998-09-01

    The conversion of carbon particles in gasification processes was investigated in a fluidized-bed reactor of the Institute of Chemical Engineering and Steam Boiler Technology of Stuttgart University. This reactor is heated electrically to process temperature, and freeboard coal particles can be sampled using an isokinetic probe. The fuel used in the experiments consisted of beech wood chips. The temperature and air rating, i.e. the main parameters of the process, were varied in order to investigate their influence on product gas quality and carbon conversion. The conversion rate is influenced to a significant extent by grain disintegration and discharge of carbon particles. In gasification conditions, a further conversion process takes place in the freeboard. (orig.) [Deutsch] In dieser Arbeit wird die Umsetzung von Kohlenstoffpartikeln unter Vergasungsbedingungen untersucht. Die Versuche wurden an einem Wirbelschichtreaktor des Instituts fuer Verfahrenstechnik und Dampfkesselwesen der Universitaet Stuttgart durchgefuehrt. Dieser Reaktor wird elektrisch auf Prozesstemperatur beheizt. Mit Hilfe einer isokinetischen Sonde koennen Proben von Kohlenstoffpartikeln im Freeboard genommen werden. Als Brennstoff wurden zerkleinerte Buchenholz-Hackschnitzel eingesetzt. Variiert wurden als Hauptparameter des Prozesses Temperatur und Luftzahl. Untersucht wurde der Einfluss dieser Parameter auf die Qualitaet des Produktgases und die Umsetzung des Kohlenstoffes. Kornzersetzungs- und Austragsvorgaenge von Kohlenstoffpartikeln spielen eine wichtige Rolle fuer den Kohlenstoffumsatz. Unter Vergasungsbedingungen findet im Freeboard eine weitere Umsetzung der Partikel statt. (orig.)

  19. Catalytic pyrolysis of woody biomass in a fluidized bed reactor: influence of the zeolite structure

    Energy Technology Data Exchange (ETDEWEB)

    A. Aho; N. Kumar; K. Eranen; T. Salmi; M. Hupa; D.Yu. Murzin [Aabo Akademi University, Aabo/Turku (Finland). Process Chemistry Centre, Laboratory of Industrial Chemistry and Reaction Engineering

    2008-09-15

    Catalytic pyrolysis of biomass from pine wood was carried out in a fluidized bed reactor at 450{sup o}C. Different structures of acidic zeolite catalysts were used as bed material in the reactor. Proton forms of Beta, Y, ZSM-5, and Mordenite were tested as catalysts in the pyrolysis of pine, while quartz sand was used as a reference material in the non-catalytic pyrolysis experiments. The yield of the pyrolysis product phases was only slightly influenced by the structures, at the same time the chemical composition of the bio-oil was dependent on the structure of acidic zeolite catalysts. Ketones and phenols were the dominating groups of compounds in the bio-oil. The formation of ketones was higher over ZSM-5 and the amount of acids and alcohols lower than over the other bed materials tested. Mordenite and quartz sand produced smaller quantities of polyaromatic hydrocarbons than the other materials tested. It was possible to successfully regenerate the spent zeolites without changing the structure of the zeolite. 12 refs., 9 figs., 5 tabs.

  20. How spectroscopy and microspectroscopy of degraded wood contribute to understand fungal wood decay.

    Science.gov (United States)

    Fackler, Karin; Schwanninger, Manfred

    2012-11-01

    Nuclear magnetic resonance, mid and near infrared, and ultra violet (UV) spectra of wood contain information on its chemistry and composition. When solid wood samples are analysed, information on the molecular structure of the lignocellulose complex of wood e.g. crystallinity of polysaccharides and the orientation of the polymers in wood cell walls can also be gained. UV and infrared spectroscopy allow also for spatially resolved spectroscopy, and state-of-the-art mapping and imaging systems have been able to provide local information on wood chemistry and structure at the level of wood cells (with IR) or cell wall layers (with UV). During the last decades, these methods have also proven useful to follow alterations of the composition, chemistry and physics of the substrate wood after fungi had grown on it as well as changes of the interactions between the wood polymers within the lignocellulose complex caused by decay fungi. This review provides an overview on how molecular spectroscopic methods could contribute to understand these degradation processes and were able to characterise and localise fungal wood decay in its various stages starting from the incipient and early ones even if the major share of research focussed on advanced decay. Practical issues such as requirements in terms of sample preparation and sample form and present examples of optimised data analysis will also be addressed to be able to detect and characterise the generally highly variable microbial degradation processes within their highly variable substrate wood.

  1. A proposed holistic approach to on-chip, off-chip, test, and package interconnections

    Science.gov (United States)

    Bartelink, Dirk J.

    1998-11-01

    The term interconnection has traditionally implied a `robust' connection from a transistor or a group of transistors in an IC to the outside world, usually a PC board. Optimum system utilization is done from outside the IC. As an alternative, this paper addresses `unimpeded' transistor-to-transistor interconnection aimed at reaching the high circuit densities and computational capabilities of neighboring IC's. In this view, interconnections are not made to some human-centric place outside the IC world requiring robustness—except for system input and output connections. This unimpeded interconnect style is currently available only through intra-chip signal traces in `system-on-a-chip' implementations, as exemplified by embedded DRAMs. Because the traditional off-chip penalty in performance and wiring density is so large, a merging of complex process technologies is the only option today. It is suggested that, for system integration to move forward, the traditional robustness requirement inherited from conventional packaging interconnect and IC manufacturing test must be discarded. Traditional system assembly from vendor parts requires robustness under shipping, inspection and assembly. The trend toward systems on a chip signifies willingness by semiconductor companies to design and fabricate whole systems in house, so that `in-house' chip-to-chip assembly is not beyond reach. In this scenario, bare chips never leave the controlled environment of the IC fabricator while the two major contributors to off-chip signal penalty, ESD protection and the need to source a 50-ohm test head, are avoided. With in-house assembly, ESD protection can be eliminated with the precautions already familiar in plasma etching. Test interconnection impacts the fundamentals of IC manufacturing, particularly with clock speeds approaching 1GHz, and cannot be an afterthought. It should be an integral part of the chip-to-chip interconnection bandwidth optimization, because—as we must

  2. A scalable single-chip multi-processor architecture with on-chip RTOS kernel

    NARCIS (Netherlands)

    Theelen, B.D.; Verschueren, A.C.; Reyes Suarez, V.V.; Stevens, M.P.J.; Nunez, A.

    2003-01-01

    Now that system-on-chip technology is emerging, single-chip multi-processors are becoming feasible. A key problem of designing such systems is the complexity of their on-chip interconnects and memory architecture. It is furthermore unclear at what level software should be integrated. An example of a

  3. School playground surfacing and arm fractures in children: a cluster randomized trial comparing sand to wood chip surfaces.

    Directory of Open Access Journals (Sweden)

    Andrew W Howard

    2009-12-01

    Full Text Available The risk of playground injuries, especially fractures, is prevalent in children, and can result in emergency room treatment and hospital admissions. Fall height and surface area are major determinants of playground fall injury risk. The primary objective was to determine if there was a difference in playground upper extremity fracture rates in school playgrounds with wood fibre surfacing versus granite sand surfacing. Secondary objectives were to determine if there were differences in overall playground injury rates or in head injury rates in school playgrounds with wood fibre surfacing compared to school playgrounds with granite sand surfacing.The cluster randomized trial comprised 37 elementary schools in the Toronto District School Board in Toronto, Canada with a total of 15,074 students. Each school received qualified funding for installation of new playground equipment and surfacing. The risk of arm fracture from playground falls onto granitic sand versus onto engineered wood fibre surfaces was compared, with an outcome measure of estimated arm fracture rate per 100,000 student-months. Schools were randomly assigned by computer generated list to receive either a granitic sand or an engineered wood fibre playground surface (Fibar, and were not blinded. Schools were visited to ascertain details of the playground and surface actually installed and to observe the exposure to play and to periodically monitor the depth of the surfacing material. Injury data, including details of circumstance and diagnosis, were collected at each school by a prospective surveillance system with confirmation of injury details through a validated telephone interview with parents and also through collection (with consent of medical reports regarding treated injuries. All schools were recruited together at the beginning of the trial, which is now closed after 2.5 years of injury data collection. Compliant schools included 12 schools randomized to Fibar that installed

  4. Life cycle environmental impacts of different construction wood waste and wood packaging waste processing methods

    OpenAIRE

    Manninen, Kaisa; Judl, Jáchym; Myllymaa, Tuuli

    2016-01-01

    This study compared the life cycle environmental impacts of different wood waste processing methods in three impact categories: climate impact, acidification impacts and eutrophication impacts. The wood waste recovery methods examined were the use of wood waste in terrace boards made out of wood composite which replace impregnated terrace boards, incineration of wood waste in a multi-fuel boiler instead of peat and the use of wood waste in the production of particleboard in either Finland or ...

  5. Mathematical Simulation of Temperature Profiles within Microwave Heated Wood Made for Wood-Based Nano composites

    International Nuclear Information System (INIS)

    Li, X.; He, X.; Lv, J.; Wu, Y.; Luo, Y.; Chen, H.

    2013-01-01

    High intensive microwave pretreatment is a new method to modify wood for the fabrication of wood-based nano composites. Based on the physical law on heat transfer, a mathematical model to describe the temperature profiles within wood heated by high intensive microwave was established and simulated in this research. The results showed that the temperature profiles within wood were related to microwave heating methods; The temperature inside wood firstly increased and then gradually decreased along the direction of microwave transmission when the unilateral microwave heating was applied, and the temperature difference along the thickness direction of wood was very significant; The temperature with wood firstly increased and then gradually decreased from the wood surface to interior when the bilateral microwave heating was applied. Compared with the unilateral microwave heating, bilateral microwave heating is a better microwave heating method for the more uniform wood microwave pretreatment.

  6. Chip compacting press; Jido kirikuzu asshukuki

    Energy Technology Data Exchange (ETDEWEB)

    Oura, K. [Yuken Kogyo Co. Ltd., Kanagawa (Japan)

    1998-08-15

    The chips exhausted from various machine tools are massy, occupy much space and make working environment worse by staying added cutting oil to lower part. The chips are exhausted as a result of machining and have not constant quality. Even if used material is same the chips have various shapes and properties by kinds and machining methods of used machine tools, and are troublesome materials from a standpoint of their treatment. Pressing and solidification of the chips have frequently been tried. A chip compacting press introduced in this paper, a relatively cheap chip compacting press aimed for relatively small scale chip treatment, and has such characteristics and effects as follows. Chips are pressed and solidified by each raw material, so fractional management can be easily conducted. As casting metal chips and curled chips of iron and aluminum can be pressed to about 1/3 to 1/5 and about 1/40, respectively, space saving can be conducted. Chip compacting pressing upgrades its transporting efficiency to make possible to reduce its transporting cost. As chip solidification controls its oxidation and most cutting oil are removed, chips are easy to recycle. 2 figs., 1 tab.

  7. Many Roles of Wood Adhesives

    Science.gov (United States)

    Charles R. Frihart

    2014-01-01

    Although wood bonding is one of the oldest applications of adhesives, going back to early recorded history (1), some aspects of wood bonds are still not fully understood. Most books in the general area of adhesives and adhesion do not cover wood bonding. However, a clearer understanding of wood bonding and wood adhesives can lead to improved products. This is important...

  8. Urban Wood Waste Resource Assessment

    Energy Technology Data Exchange (ETDEWEB)

    Wiltsee, G.

    1998-11-20

    This study collected and analyzed data on urban wood waste resources in 30 randomly selected metropolitan areas in the United States. Three major categories wood wastes disposed with, or recovered from, the municipal solid waste stream; industrial wood wastes such as wood scraps and sawdust from pallet recycling, woodworking shops, and lumberyards; and wood in construction/demolition and land clearing debris.

  9. Methanol production from Eucalyptus wood chips. Working document I. The Florida Eucalyptus energy farm: silvicultural methods and considerations

    Energy Technology Data Exchange (ETDEWEB)

    Fishkind, H.H.

    1982-04-01

    The silvicultural matrix within which the nation's first large scale wood energy plantation will develop is described in detail. The relevant literature reviewed is identified and distilled. The plantation history, site preparation, planting, species selection, maintenance and management, harvesting, and the Eucalyptus biomass production estimates are presented.

  10. CFD Modelling of Biomass Combustion in Small-Scale Boilers. Final Report

    Energy Technology Data Exchange (ETDEWEB)

    Xue-Song Bai; Griselin, Niklas; Klason, Torbern; Nilsson, Johan [Lund Inst. of Tech. (Sweden). Dept. of Heat and Power Engineering

    2002-10-01

    This project deals with CFD modeling of combustion of wood in fixed bed boilers. A flamelet model for the interaction between turbulence and chemical reactions is developed and applied to study small-scale boiler. The flamelet chemistry employs 43 reactive species and 174 elementary reactions. It gives detailed distributions of important species such as CO and NO{sub x} in the flow field and flue gas. Simulation of a small-scale wood fired boiler measured at SP Boraas (50 KW) shows that the current flamelet model yields results agreeable to the available experimental data. A detailed chemical kinetic model is developed to study the bed combustion process. This model gives boundary conditions for the CFD analysis of gas phase volatile oxidation in the combustion chambers. The model combines a Functional Group submodel with a Depolymerisation, Vaporisation and Crosslinking submodel. The FG submodel simulates how functional groups decompose and form light gas species. The DVC submodell predicts depolymerisation and vaporisation of the macromolecular network and this includes bridge breaking and crosslinking processes, where the wood structure breaks down to fragments. The light fragments form tar and the heavy ones form metaplast. Two boilers firing wood log/chips are studied using the FG-DVC model, one is the SP Boraas small-scale boiler (50 KW) and the other is the Sydkraft Malmoe Vaerme AB's Flintraennan large-scale boiler (55 MW). The fix bed is assumed to be two zones, a partial equilibrium drying/devolatilisation zone and an equilibrium zone. Three typical biomass conversion modes are simulated, a lean fuel combustion mode, a near-stoichiometric combustion and a fuel rich gasification mode. Detailed chemical species and temperatures at different modes are obtained. Physical interpretation is provided. Comparison of the computational results with experimental data shows that the model can reasonably simulate the fixed bed biomass conversion process. CFD

  11. Fouling and slagging problems at recovered wood fuel combustion; Orsaker till askrelaterade driftproblem vid eldning av returtraeflis

    Energy Technology Data Exchange (ETDEWEB)

    Andersson, Christer; Hoegberg, Jan [Vattenfall Utveckling AB, Stockholm (Sweden)

    2001-03-01

    CHP-plants that use a large portion of sorted wood waste fuel can face ash-related problems. By analysing the circumstances about these problems, the goal is to find causes for the problems and measures that can be taken. This knowledge can then be utilised in plants where it is desired to increase the portion of sorted wood waste fuel. For the measurements, a deposit probe is a good tool to use since the result is independent of many boiler-specific factors. Compared with forest residues, sorted wood waste causes a more problematic ash. The risk of troublesome fouling and corrosion seems to increase with increased admixture of sorted wood waste fuel. Plugging of the grate is associated with melts that are formed from metallic contamination in the fuel. These melts obstruct the air holes. The melts that have been seen during the project have had a content of aluminium, brass and zinc. In order to solve these problems, the construction and cooling of the grate and quality assurance of the fuel are important aspects. One problem that was found in all of the studied boilers (grates as well as fluidized beds) is growth of fouling on surfaces for heat transfer. Measurements with deposit probe show that the initial growth rate on superheaters are approximately 3 - 5 times higher when sorted wood waste is used than if forest residues is used. Even if this growth rate can not be extrapolated to a complete operating season, the relative difference between the fuels remains. The extent of the problem depends on the dimensioning of the boiler. The fouling tends to have a light outer layer that can be disadvantageous for the absorption of heat radiation. Haendeloe P11 needs for example to be stopped for cleaning with an interval of 2 - 3 months because of lost heat absorption in the furnace and the convection path. The most obvious ash related problem that was found in Haendeloe P11 when 100 % sorted wood waste fuel was used was corrosion on the walls of the lower parts of the

  12. Radioactivity of Wood and Environment

    International Nuclear Information System (INIS)

    Hus, M.; Kosutic, K.; Lulic, S.

    2003-01-01

    Nuclear experiments in the atmosphere and nuclear accidents caused global deposition of artificial radionuclides in the soil of Earth's northern hemisphere, the territory of the Republic of Croatia included. Soil contamination by radionuclides resulted in their deposition in plants growing on the contaminated soil as well as in the trees. Large area of the Republic of Croatia is covered with wood, which is exploited in manufacture of industrial wood and for firewood. From approximately 3 million cubic metres of wood exploited annually, nearly one third serves for firewood. In the process of burning a smaller portion of radionuclides deposited in the wood evaporates and goes to atmosphere while a larger portion is retained in the ash. In this paper are presented the results of natural radionuclides 4 0K , 2 32T h and 2 38U as well as of artificial radionuclide 1 37C s content determination in the wood, wood briquette, charcoal and in ash remained after burning the wood, wood briquette and charcoal. The obtained results are discussed from wood radiocontamination aspect and from the aspect of potential environmental radiocontamination by the products from wood burning process. (author)

  13. Wood construction under cold climate

    DEFF Research Database (Denmark)

    Wang, Xiaodong; Hagman, Olle; Sundqvist, Bror

    2014-01-01

    As wood constructions increasingly use engineered wood products worldwide, concerns arise about the integrity of the wood and adhesives system. The glueline stability is a crucial issue for engineered wood application, especially under cold climate. In this study, Norway spruce (Picea abies...... affected shear strength of wood joints. As temperature decreased, the shear strength decreased. PUR resin resulted in the strongest shear strength at all temperatures tested. MF resin responded to temperature changes in a similar ways as the PUR resin. The shear strength of wood joints with EPI resins...... specimens need to be tested in further work to more completely present the issue. The EN 301 and EN 302 may need to be specified based on wood species....

  14. Efficacy of Selected Insecticide Sprays and Aerosols against the Common Bed Bug, Cimex lectularius (Hemiptera: Cimicidae

    Directory of Open Access Journals (Sweden)

    Changlu Wang

    2016-01-01

    Full Text Available We evaluated the residual efficacy of four liquid sprays and four ready-to-use aerosols that are commonly used in the U.S. against a field-collected bed bug, Cimex lectularius L., strain with moderate resistance level to pyrethroids. The four liquid sprays were: Tandem (0.1% thiamethoxam, 0.03% lambda-cyhalothrin, Temprid SC (0.05% imidacloprid, 0.025% cyfluthrin, Transport GHP (0.05% acetamiprid, 0.06% bifenthrin, and Demand CS (0.03% lambda-cyhalothrin. The four aerosols were: Alpine (0.5% dinotefuran, Bedlam (0.4% sumithrin, 1.6% MGK 264, Bedlam Plus (0.4% sumithrin, 1% MGK 264, 0.05% imidacloprid, and Phantom (0.5% chlorfenapyr. Bed bugs were confined for 4 h to treated substrates (aged 24 h. Four substrates were tested: fabric, unpainted wood, painted wood, and vinyl. Bedlam, Demand CS, and Temprid SC resulted in ≤70% mortality on all tested substrates. Among the other five products, substrate type significantly affected their residual efficacy, except for Transport GHP, which caused ≥89.7% mortality regardless of the substrate. The effect of exposure time (5 min, 4 h, and 24 h on the efficacy of Transport GHP and Phantom aerosol also was evaluated. A 4 h continuous exposure to Phantom aerosol or Transport GHP residue caused similar mortality to 24 h exposure and higher mortality than 5 min exposure.

  15. Gasification-based energy production systems for different size classes - Potential and state of R and D

    International Nuclear Information System (INIS)

    Kurkela, E.

    1997-01-01

    (Conference paper). Different energy production systems based on biomass and waste gasification are being developed in Finland. In 1986-1995 the Finnish gasification research and development activities were almost fully devoted to the development of simplified IGCC power systems suitable to large-scale power production based on pressurized fluid-bed gasification, hot gas cleaning and a combined-cycle process. In the 1990's the atmospheric-pressure gasification activities aiming for small and medium size plants were restarted in Finland. Atmospheric-pressure fixed-bed gasification of wood and peat was commercialized for small-scale district heating applications already in the 1980's. Today research and development in this field aims at developing a combined heat and power plant based on the use of cleaned product gas in internal combustion engines. Another objective is to enlarge the feedstock basis of fixed-bed gasifiers, which at present are limited to the use of piece-shaped fuels such as sod peat and wood chips. Intensive research and development is at present in progress in atmospheric-pressure circulating fluidized-bed gasification of biomass residues and wastes. This gasification technology, earlier commercialized for lime-kiln applications, will lead to co-utilization of local residues and wastes in existing pulverized coal fired boilers. The first demonstration plant is under construction in Finland and there are several projects under planning or design phase in different parts of Europe. 48 refs., 1 fig., 1 tab

  16. Effects of biomass on dynamics of combustion in circulating fluidized beds

    Directory of Open Access Journals (Sweden)

    Tourunen Antti

    2004-01-01

    Full Text Available Fluidized bed technology is very suitable for the combustion of biomass Nevertheless substitution of coal with biomass affects boiler operation and especially dynamics and controllability. Non-homogeneity of biomass and fuel feeding disturbances cause process instability, such as variations in temperatures and pressures, which reduce lifetime of equipment and structures. Because of process instability higher air coefficient must be used in order to avoid CO emissions, which is not economical. Combustion profiles for coal, wood and peat, measured at the VTT Processes Pilot circulating fluidized bed reactor, have been compared. Process stability and char inventories have been studied by the measurements and the model. Biofuel are usually very reactive and their combustion profiles are quite different compared to coals. Because of high reactivity and low char content combustion process with biofuel is very sensitive for fuel feeding. Also low char inventory effect on load changes combined with combustion profile that differs from coals. Because of different combustion profile heat transfer can be a limiting factor in load changes despite the high reactivity and fast oxygen response.

  17. Controversy. The wood war

    International Nuclear Information System (INIS)

    James, O.

    2010-01-01

    The author comments the conflict emerging in France between industries exploiting wood for construction and those exploiting it as a heating material for power generation. The first ones accuse the others to steal their raw material, to pull the prices up, and to destabilize the sector. This conflict takes place notably around sawmill wastes which are used either by wood panel fabricators or by wood pellets producers. Both sectors are claiming they are creating more jobs than the other. The French forest indeed offers good opportunities for both sectors, but other countries which are lacking forest surfaces, are buying wood in France. Several issues are matter of discussion: burning wood seems to go against the reduction of greenhouse gas emissions, subsidies awarded to big heater projects. The situation of the wood sector in Austria, Finland and Poland is briefly presented

  18. On-chip electrochromic micro display for a disposable bio-sensor chip

    Science.gov (United States)

    Zhu, Yanjun; Tsukamoto, Takashiro; Tanaka, Shuji

    2017-12-01

    This paper reports an on-chip electrochromic micro display made of polyaniline (PANi) which can be easily made on a CMOS chip. Micro-patterned PANi thin films were selectively deposited on pre-patterned microelectrodes by using electrodeposition. The optimum conditions for deposition and electrochromism were investigated. An 8-pixel on-chip micro display was made on a Si chip. The color of each PANi film could be independently but simultaneously controlled, which means any 1-byte digital data could be displayed on the display. The PANi display had a response time as fast as about 100 ms, which means the transfer data rate was as fast as 80 bits per second.

  19. The effects of chronic exposure to common bedding materials on the metabolic rate and overall health of male CD-1 mice.

    Science.gov (United States)

    Becker, Corey E; Mathur, Carolyn F; Rehnberg, Bradley G

    2010-01-01

    Anecdotes and personal Web pages claim that cedar and pine beddings cause respiratory distress in rodents, although no previous research could be found to support these claims. There have, however, been published studies of respiratory distress in cedar and pine mill workers. That research links exposure to wood dust to asthma and to bronchial and alveolar damage in humans. This study looks at the effects of 3 types of bedding (CareFRESH Original, cedar, and pine) on the growth, food intake, oxygen consumption, IgE antibody concentrations, and general appearance and behavior in male CD-1 mice. Mice who were housed on these beddings for approximately 4 months did not show significant differences in any of these variables. This suggests that these 3 materials provide equally healthy substrates for long-term rearing of mice and possibly other rodents.

  20. Harvesting techniques for energy wood of forest owners; Metsaenomistajien energiapuun korjuutekniikat

    Energy Technology Data Exchange (ETDEWEB)

    Ryynaenen, S. [Work Efficiency Inst., Rajamaeki (Finland)] Ihonen, M. [Work Efficiency Inst., Helsinki (Finland)

    1997-12-01

    The aim of the project is to develop harvesting techniques and methods for small-wood and logging residues, suitable for use by forest owners and small-scale entrepreneurs. Examples of such methods are piling of logging residues at site and forest transport with farm tractors. The project is carried out by field experiments with new machines and methods and by work-studies at sites in practice. A cost-accounting model for firewood production will also be revised. The work study of the harvesting method of first- thinning wood and energy wood based on the use of SykeNaarva logging equipment was carried out as part of chips supply to Perho Energy Co-operative. The productivity of logging was in practice significantly higher than in previous field tests with the prototype equipment. The costs were lower than in manual logging. Field experiments were also carried out with manual logging with a chain saw equipped with felling grips (Reo-Tuote Ky). Operation experiments with a chain-limbing device for farm tractors (Eskon Paja Oy), related to product development, were also carried out. A literature study, specialist interviews and field experiments were carried out on the transports of logging residues with farm factors. A four-drive tractor equipped with a timber loader and a trailer is suited technically for this work. Productivity is reduced by slow loading and in particular by a small load size when operating with the basic fleet. The costs are reduced by small capital costs and by rapid transports between the sites. To improve the economy of harvesting logging residues, inexpensive technical solutions were studied for farm tractors in co-operation with engineering works

  1. Effect of ionization, bedding, and feeding on air quality in a horse stable.

    Science.gov (United States)

    Siegers, Esther Willemijn; Anthonisse, Milou; van Eerdenburg, Frank J C M; van den Broek, Jan; Wouters, Inge M; Westermann, Cornélie Martine

    2018-05-01

    Organic dust is associated with Equine asthma. Ionization should reduce airborne dust levels. To determine the effect of ionization of air, type of bedding, and feed on the levels of airborne dust, endotoxin, and fungal colonies in horse stables. 24 healthy University-owned horses occupied the stables. A randomized controlled cross-over study. Four units with 6 stables were equipped with an ionization installation (25 VA, 5000 Volt Direct Current). Horses were kept either on wood shavings and fed haylage (2 units), or on straw and fed dry hay (2 units). Measurements were performed with and without activated ionization, during daytime and nighttime, repeatedly over the course of a week and repeatedly during 4-6 weeks. Statistical analysis was performed using a mixed effect model with Akaike's Information Criterion for model reduction and 95% profile (log) likelihood confidence intervals (CI). Ionization did not alter concentrations of dust, endotoxin, or fungi, fewer. In the units with straw and hay, the concentration of dust, endotoxin, and fungi (difference in logarithmic mean 1.92 (95%CI 1.71-2.12); 2.86 (95%CI 2.59-3.14); 1.75 (95%CI 1.13-2.36)) were significantly higher compared to wood shavings and haylage. The installation of a negative air-ionizer in the horse stable did not reduce concentrations of dust, endotoxin, and viable fungal spores. The substantial effect of low dust bedding and feed is confirmed. Copyright © 2018 The Authors. Journal of Veterinary Internal Medicine published by Wiley Periodicals, Inc. on behalf of the American College of Veterinary Internal Medicine.

  2. Reliable and non-destructive positioning of larvae of wood-destroying beetles in wood

    International Nuclear Information System (INIS)

    Kerner, G.; Thiele, H.; Unger, W.

    1980-01-01

    Living larvae of wood-destroying insects (house longhorn beetle, deathwatch) can be determined in wood by both X-ray technique and vibration measurements. For such examinations convenient commercial devices were used and tested under laboratory conditions. The methods complement each other and lead to a rationalization of the tests of wood preservatives against wood-destroying insects. It seems to be promising to apply the test methods also to timber already used for building

  3. Infant's bed climate and bedding in the Japanese home.

    Science.gov (United States)

    Nakamura Ikeda, Rie; Fukai, Kiyoko; Okamoto Mizuno, Kazue

    2012-06-01

    to assess the bed climate of infants in their homes in Japan. descriptive, exploratory, non-experimental research design. the data were collected at the participants' homes under normal circumstances. nineteen healthy infants between the ages of two and five months. Their mothers, who joined a parenting class organised by a maternity clinic in Okayama, Japan, consented to participate in this study. we visited the infants' homes and interviewed their mothers concerning the types and use of bedding. The temperature and relative humidity of the bed climate at the back and foot of the bedding, and in the room were measured every minute for four consecutive days. Differences among the bed climates measured during three seasons (spring, summer, and autumn) were assessed by one-way analysis of variance. The bed temperature was higher for infants than for adults. No significant difference in temperature was noted among the three seasons. The bed temperature was about 36.0°C when waterproof sheets and futon mattresses for children or adult were used. The average relative humidity of the bed climate at the back was highest in summer, followed by that in spring and autumn; the differences were significant. The use of waterproof sheets and futon mattresses for children in summer increased the relative humidity to 80% or more. The use of infant beds, sunoko drainboards, and cotton futon mattresses in summer was effective in reducing the bed humidity. these results suggest that nurse-midwives should advise the parents on comfortable bed climates for their infants, as well as how to select and use bedding for them. Copyright © 2010 Elsevier Ltd. All rights reserved.

  4. Willow as fuel for district heating. Experiences from test combustion; Energipil som braendsel til fjernvarme - Erfaringsindsamling fra testfyringer

    Energy Technology Data Exchange (ETDEWEB)

    Pedersen, Joergen

    2012-10-15

    The project has been a study of the fuel characteristics of willow chips. The study was carried out on Trustrup-Lyngby Heating Plant and Assens District Heating Plant in the period 2011-12. Operating experiences were collected from the two plants. Furthermore, yield and crop data were collected from suppliers of willow chips to Assens District Heating Plant, and the analysis of particle size distribution of the willow chips is carried out. The collected data on yield and particle size distribution are compared with results from previous studies. The project has shown that willow chips generally are a suitable and attractive fuel in wood-fired heat and power plants. The plants are very aware of quality of willow chips and want chips with coarse structure. Furthermore, there is the wish that water content of willow chips are on par with the moisture content of wood chips, i.e. around 30-40%; woodchips are the vast majority of the chips used in the plants. Wood chips produced from fresh willow shoots with chopper will typically have a moisture content of 50-60 %. Such ''wet'' chips will of some plants be deselected during winter, where there is a requirement of safe and high boiler output. Other plants will simply mix the ''wet'' willow chips with other, drier types of chips and can use it almost all the year. If the willow shoots are harvested as branches, which subsequently are allowed to dry for a period before chipping, willow chips can be produced with a moisture content that is in line with what is typical in wood chips. Analysis of particle size distribution shows that willow chips harvested with a cutting machine usually can meet the requirements for quality classes ''fine'', ''medium'' and ''coarse''. An account of the harvested yields of willow among the growers who supplied willow chips to Assens Heating Plant, showed a relatively low yield of 5.1 tonnes dry

  5. Request for wood samples

    NARCIS (Netherlands)

    NN,

    1977-01-01

    In recent years the wood collection at the Rijksherbarium was greatly expanded following a renewed interest in wood anatomy as an aid for solving classification problems. Staff members of the Rijksherbarium added to the collection by taking interesting wood samples with them from their expeditions

  6. The economy of chip, tree section and short wood methods in the procurement of a pulp mill; Hake-, puu- ja puutavaralajimenetelmien taloudellisuus massatehtaan kuitu- ja energiapuun hankinnassa

    Energy Technology Data Exchange (ETDEWEB)

    Imponen, V [Metsaeteho Oy, Helsinki (Finland)

    1997-12-01

    Regional forest management plans for Finland`s private, non-industrial forestry indicate that first thinnings account for 13 % of the felling potential in these forests. The majority of first thinnings focus on pine-dominated stands. First-thinnings wood represents 29 % of the allowable cut consisting of pine pulpwood. However, small-diameter pine has not enjoyed great demand as raw material by the chemical pulp industry due to the high associated production costs and due to its inferior fibre properties when compared to large-sized softwood logs. Consequently, research and development work has been focused on the procurement, handling and usage of small-diameter wood, and especially of first-thinning pine. Both defibration and use as fuel are options when considering how to exploit small-diameter softwood raw material. Integrated procurement of industrial wood and wood fuel have improved the profitability of wood from thinnings in pulp manufacture and in energy generation at the mill. These methods would appear to be economic in regard to both the wood procurement of the pulp mills even at the present prices paid for alternative fuels. Advances in combustion technology and increased generation of electric power improve the competitiveness of methods based on the harvesting tree sections in comparison with the shortwood system yielding delimbed roundwood. The adoption of longer timber lorry-trailer combination as recognised by EU directives will have the effect of reducing the transportation costs for non-delimbed and partially delimbed wood. (orig.)

  7. Wood fuel and the environment

    International Nuclear Information System (INIS)

    Foster, C.A.

    1992-01-01

    The purpose of this paper is to try and demonstrate the role that the use of Wood as a Fuel can play in our environment. The term ''Wood Fuel'', for the purposes of these proceedings, refers to the use of wood obtained from the forest or the farm. It does not refer to waste wood from for example buildings. The role of wood fuel in the environment can be assessed at many different levels. In this paper three different scales of ''Environment'' and the role of wood fuel in each, will be considered. These three scales are namely the global environment, the local environment, and the National (community) environment. (Author)

  8. Wood-plastic combination

    International Nuclear Information System (INIS)

    Schaudy, R.

    1978-02-01

    A review on wood-plastic combinations is given including the production (wood and plastic component, radiation hardening, curing), the obtained properties, present applications and prospects for the future of these materials. (author)

  9. Experimental studies on pulp and paper mill sludge ash behavior in fluidized bed combustors

    Energy Technology Data Exchange (ETDEWEB)

    Latva-Somppi, J. [VTT Chemical Technology, Espoo (Finland). Process Technology

    1998-11-01

    Ash formation during the fluidized bed combustion (FBC) of pulp and paper mill sludges has been experimentally studied on an industrial and bench scale. The methods included aerosol measurements, chemical and crystalline composition analyses, thermogravimetry and electron microscopy. Fly ash mass and number size distributions and elemental enrichment in submicron particles and bottom ash were measured. Fly ash, bottom ash and ash deposits were characterized and their formation mechanisms are discussed. During combustion the fine paper-making additives in sludge, clay minerals and calcite, sintered fanning porous agglomerates. The fly ash mass mean size was 7.5 - 15 lam and the supermicron particles included 93.6 - 97.3 % of the fly ash. Condensation of the volatilized inorganic species formed spherical submicron particles in the fly ash. Their mass concentration was almost negligible when co-firing paper mill sludges and wood. This suggests that the fraction of the volatilized inorganic species in the paper mill sludges was low. Results from pulp mill sludge and bark co-firing were different. A clear mass mode below 0.3 pm, presenting 2.2 - 5.0 weight-% of the fly ash was detected. The condensed species included K, Na, S and Cl. Their mass fraction was higher in the pulp mill sludge than in the paper mill sludge. Evidently this resulted in increased volatilization and formation of condensed particles. The following trace elements were enriched in the submicron ash during pulp mill sludge and wood co-firing: As, Cd, Rb and Pb. The main part of the volatile species was, however, captured in the bulk ash. Presumably, this was due to the high surface area concentration in the bulk ash. Sludge moisture was observed to reduce the inorganic species volatilization. Probably steam vaporization from the wet sludge through the burning layer decreased combustion temperatures on char surface and less char was produced. Hence, the volatilization of ash forming species was

  10. "Hook"-calibration of GeneChip-microarrays: Chip characteristics and expression measures

    Directory of Open Access Journals (Sweden)

    Krohn Knut

    2008-08-01

    Full Text Available Abstract Background Microarray experiments rely on several critical steps that may introduce biases and uncertainty in downstream analyses. These steps include mRNA sample extraction, amplification and labelling, hybridization, and scanning causing chip-specific systematic variations on the raw intensity level. Also the chosen array-type and the up-to-dateness of the genomic information probed on the chip affect the quality of the expression measures. In the accompanying publication we presented theory and algorithm of the so-called hook method which aims at correcting expression data for systematic biases using a series of new chip characteristics. Results In this publication we summarize the essential chip characteristics provided by this method, analyze special benchmark experiments to estimate transcript related expression measures and illustrate the potency of the method to detect and to quantify the quality of a particular hybridization. It is shown that our single-chip approach provides expression measures responding linearly on changes of the transcript concentration over three orders of magnitude. In addition, the method calculates a detection call judging the relation between the signal and the detection limit of the particular measurement. The performance of the method in the context of different chip generations and probe set assignments is illustrated. The hook method characterizes the RNA-quality in terms of the 3'/5'-amplification bias and the sample-specific calling rate. We show that the proper judgement of these effects requires the disentanglement of non-specific and specific hybridization which, otherwise, can lead to misinterpretations of expression changes. The consequences of modifying probe/target interactions by either changing the labelling protocol or by substituting RNA by DNA targets are demonstrated. Conclusion The single-chip based hook-method provides accurate expression estimates and chip-summary characteristics

  11. An Analysis of the U.S. Wood Products Import Sector: Prospects for Tropical Wood Products Exporters

    Directory of Open Access Journals (Sweden)

    W.A.R.T.W. Bandara

    2012-10-01

    Full Text Available The U.S. has dramatically altered its wood product imports and exports during the past few years,and at present, it is the second largest wood product importer in the world. Hence, an understanding ofmarket structures, factors in selecting foreign suppliers, and the emphasis placed on environmentalissues/certification are critical to understand from the perspective of wood products importers in the U.S.This study provides an analysis of the U.S. wood products import sector with special emphasis on currentand future opportunities for tropical wood products exporters to the U.S. market.In this study, 158 wood products importers in the U.S. were surveyed using a mailingquestionnaire. The adjusted response rate was 40.6 percent. Results indicated that most of the respondentswere small to medium scale firms, but major importers of wood products. According to respondents,wood products to the U.S. mainly come from Brazil, Chile, and China. From the importers’ perspective,Brazilian wood products ranked first for its quality followed by wood products from Chile and Finland.Product quality, long term customer relationships, on-time delivery of orders, fair prices, and supplierreputation were the factors deemed important in selecting overseas suppliers. Majority of respondentswere importing certified wood products. FSC, SFI, and ISO 14000 were the mostly accepted certificationprograms. However, certification was not a major factor in foreign supplier selection criteria. Whenconsidered the U.S. wood products importers’ tendency to diversify their products and species imported,attractive opportunities exist for wood products suppliers from tropical countries.

  12. Wood's lamp examination

    Science.gov (United States)

    ... this page: //medlineplus.gov/ency/article/003386.htm Wood lamp examination To use the sharing features on this page, please enable JavaScript. A Wood lamp examination is a test that uses ultraviolet ( ...

  13. Pixel detector readout chip

    CERN Multimedia

    1991-01-01

    Close-up of a pixel detector readout chip. The photograph shows an aera of 1 mm x 2 mm containing 12 separate readout channels. The entire chip contains 1000 readout channels (around 80 000 transistors) covering a sensitive area of 8 mm x 5 mm. The chip has been mounted on a silicon detector to detect high energy particles.

  14. Wood preservation

    Science.gov (United States)

    Rebecca E. Ibach

    1999-01-01

    When left untreated in many outdoor applications, wood becomes subject to degradation by a variety of natural causes. Although some trees possess naturally occurring resistance to decay (Ch. 3, Decay Resistance), many are in short supply or are not grown in ready proximity to markets. Because most commonly used wood species, such as Southern Pine, ponderosa pine, and...

  15. The use of new, aqueous chemical wood modifications to improve the durability of wood-plastic composites

    Science.gov (United States)

    Rebecca E. Ibach; Craig M. Clemons; George C. Chen

    2017-01-01

    The wood flour used in wood-plastic composites (WPCs) can biologically deteriorate and thus the overall mechanical performance of WPCs decrease when exposed to moisture and fungal decay. Protecting the wood flour by chemical modification can improve the durability of the wood in a nontoxic way so it is not harmful to the environment. WPCs were made with modified wood...

  16. Formation and removal of biomass-derived contaminants in fluidized-bed gasification processes

    Energy Technology Data Exchange (ETDEWEB)

    Kurkela, E [VTT Energy, Espoo (Finland). Energy Production Technologies

    1997-12-31

    The objectives of this thesis were to examine the effects of the feedstock and the operating conditions of a fluidized-bed gasifier on the formation of tars and nitrogen-containing compounds and to study the effectiveness of the hot gas cleaning methods developed for the removal of particulates, alkali metals, tars and nitrogen-containing compounds. The most essential part of the work was carried out in the pressurized fluidized-bed gasification test facilities composed of an air-blown bubbling fluidized-bed gasifier and subsequent hot gas filter unit. The operation pressure of the test rig could be varied in the range 0.3 - 1.0 MPa and the maximum allowable gasification temperature was 1 050 deg C. The maximum capacity with biomass fuels was 80 kg/h. A wide range of feedstocks from hard coals, lignite and peat to different wood derived fuels and straw were used in the gasification tests. Two different types of ceramic filters were tested in the filter unit connected to the pressurized fluidized-bed gasifier. The filter unit was operated in a temperature range of 400 - 740 deg C. The particulate removal requirements set by the gas turbines were met by both types of filters and with product gases derived from all the feedstocks tested. In addition to the gasification and gas filtration tests, catalytic tar and ammonia decomposition was studied using both laboratory and bench-scale test facilities. Inexpensive calcium-based bulk materials, dolomites and limestones, were efficient tar decomposition catalysts in atmospheric-pressure tests

  17. Formation and removal of biomass-derived contaminants in fluidized-bed gasification processes

    Energy Technology Data Exchange (ETDEWEB)

    Kurkela, E. [VTT Energy, Espoo (Finland). Energy Production Technologies

    1996-12-31

    The objectives of this thesis were to examine the effects of the feedstock and the operating conditions of a fluidized-bed gasifier on the formation of tars and nitrogen-containing compounds and to study the effectiveness of the hot gas cleaning methods developed for the removal of particulates, alkali metals, tars and nitrogen-containing compounds. The most essential part of the work was carried out in the pressurized fluidized-bed gasification test facilities composed of an air-blown bubbling fluidized-bed gasifier and subsequent hot gas filter unit. The operation pressure of the test rig could be varied in the range 0.3 - 1.0 MPa and the maximum allowable gasification temperature was 1 050 deg C. The maximum capacity with biomass fuels was 80 kg/h. A wide range of feedstocks from hard coals, lignite and peat to different wood derived fuels and straw were used in the gasification tests. Two different types of ceramic filters were tested in the filter unit connected to the pressurized fluidized-bed gasifier. The filter unit was operated in a temperature range of 400 - 740 deg C. The particulate removal requirements set by the gas turbines were met by both types of filters and with product gases derived from all the feedstocks tested. In addition to the gasification and gas filtration tests, catalytic tar and ammonia decomposition was studied using both laboratory and bench-scale test facilities. Inexpensive calcium-based bulk materials, dolomites and limestones, were efficient tar decomposition catalysts in atmospheric-pressure tests

  18. Moisture Transport in Wood

    DEFF Research Database (Denmark)

    Astrup, Thomas; Hansen, Kurt Kielsgaard; Hoffmeyer, Preben

    2005-01-01

    Modelling of moisture transport in wood is of great importance as most mechanical and physical properties of wood depend on moisture content. Moisture transport in porous materials is often described by Ficks second law, but several observations indicate that this does not apply very well to wood....... Recently at the Technical University of Denmark, Department of Civil Engineering, a new model for moisture transport in wood has been developed. The model divides the transport into two phases, namely water vapour in the cell lumens and bound water in the cell walls....

  19. Bed Bugs

    Science.gov (United States)

    Prevent, identify, and treat bed bug infestations using EPA’s step-by-step guides, based on IPM principles. Find pesticides approved for bed bug control, check out the information clearinghouse, and dispel bed bug myths.

  20. Factors driving the development of forest energy in Finland

    International Nuclear Information System (INIS)

    Hakkila, Pentti

    2006-01-01

    Renewable energy sources play an important role in the Finnish energy and climate strategies which are implemented partly through the Action Plan for Renewable Energy Sources. Enhancement of wood energy plays a key role in the plan. A special emphasis is given to forest chips produced from small-sized trees from early thinnings and above-ground and below-ground residual biomass from regeneration cuttings. The production goal of forest chips is 5 million m 3 solid (10TWh) in 2010. The use of forest chips is promoted by means of environmental taxes, financial aid for investments, and financial support for research, development and commercialization of technology. In 2002, altogether 365 heating and power plants larger than 0.4MW used forest chips. The total consumption was 1.7 million m 3 , the use of small houses and farms included. The growth of use is presently about 350000 m 3 per annum, but reaching the official goal will require an annual growth of 400000 m 3 during this decade. The consumption of roundwood per capita, 15m 3 per annum, is in Finland 20 times as high as the average consumption of the EU countries, respectively. Consequently, residual forest biomass is abundantly available. The capacity of heating and power plants to use forest chips is large enough to meet the goal. However, users require competitive chip prices, good quality control of fuel and reliable supply chains, and new efficient procurement systems are being developed. The paper deals with the drivers of this development: support measures of the Government; strong support to research, development and commercialization of forest chip production from the National Technology Agency Tekes; advanced infrastructure for the procurement of timber for the forest industries; positive attitude and active participation of the forest industries; the active role of leading forest machine and boiler manufacturers, and the possibility to cofire wood and peat fuels in large fluidized bed boilers so as to