WorldWideScience

Sample records for wo mochiita concrete

  1. Effects of micro-sized and nano-sized WO_3 on mass attenauation coefficients of concrete by using MCNPX code

    International Nuclear Information System (INIS)

    Tekin, H.O.; Singh, V.P.; Manici, T.

    2017-01-01

    In the present work the effect of tungsten oxide (WO_3) nanoparticles on mass attenauation coefficients of concrete has been investigated by using MCNPX (version 2.4.0). The validation of generated MCNPX simulation geometry has been provided by comparing the results with standard XCOM data for mass attenuation coefficients of concrete. A very good agreement between XCOM and MCNPX have been obtained. The validated geometry has been used for definition of nano-WO_3 and micro-WO_3 into concrete sample. The mass attenuation coefficients of pure concrete and WO_3 added concrete with micro-sized and nano-sized have been compared. It was observed that shielding properties of concrete doped with WO_3 increased. The results of mass attenauation coefficients also showed that the concrete doped with nano-WO_3 significanlty improve shielding properties than micro-WO_3. It can be concluded that addition of nano-sized particles can be considered as another mechanism to reduce radiation dose. - Highlights: • It was found that size of the WO_3 affected the mass attenuation coefficients of concrete in all photon energies.

  2. Soil surveying using electromagnetic methods; Denji tansaho wo mochiita jiban chosa

    Energy Technology Data Exchange (ETDEWEB)

    Suzuki, I; Kawauchi, K; Goto, N [Muroran Institute of Technology, Hokkaido (Japan); Takahashi, N; Yamada, T [Zukohsya Co. Ltd., Hokkaido (Japan)

    1997-10-22

    Electromagnetic surveying method is applied in Muroran Institute of Technology`s site for power transmission steel towers for the locating of structures buried in the ground and for the study of obstruction to the application of the method. The devices employed are the EM31 and EM38 which are portable conductivity measuring instruments manufactured by GEONICS Company. With the probeable depth in the horizontal dipole mode being approximately half that in the vertical dipole mode, depths of 0.5m, 1m, 3m, and 6m may be explored using the two instruments. In the measurement test, the devices are used to determine a reinforced concrete-made multi-purpose duct that accommodates water pipes, sewers, various electric wires, and heating pipes and is buried at a depth of 2-3m in the ground. In the measurement for a 3m-deep level, a spot high in conductivity due to the reinforced concrete is detected, and the result roughly corresponds to the lay of the duct. In the measurement for a 6m-deep level, no high-conductivity spot is found, meaning there is no such structure at this depth. Although there are some other high conductivity values recorded, they are attributed to manhole covers or steel tower bases on the ground surface. 3 refs., 8 figs.

  3. Synthesis, characterization and photocatalytic activity of WO3/TiO2 for NO removal under UV and visible light irradiation

    International Nuclear Information System (INIS)

    Luévano-Hipólito, E.; Martínez-de la Cruz, A.; López-Cuellar, E.; Yu, Q.L.; Brouwers, H.J.H.

    2014-01-01

    Samples with different proportions WO 3 /TiO 2 were prepared by co-precipitation method followed by a heat treatment. The samples were characterized by X-ray powder diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), diffuse reflectance spectroscopy (DRS), and adsorption–desorption N 2 isotherms (BET). The photocatalytic properties of WO 3 /TiO 2 samples were evaluated in the photo-oxidation reaction of nitric oxide (NO) under UV and visible light irradiation. The highest photocatalytic activity was observed in the WO 3 /TiO 2 sample with a composition of 80% mole of TiO 2 . Among the different substrates used for supporting the photocatalyst, the best results were reached over concrete and glass when it was exposed to UV and visible light irradiation, respectively. In overall, the photocatalytic efficiency of the synthesized materials was higher under UV than visible light irradiation. - Highlights: • WO 3 /TiO 2 prepared in simple way show high photocatalytic activity for NO removal. • The concrete was the best substrate to the performance of WO 3 /TiO 2 with UV radiation. • The glass was the best substrate to the performance of WO 3 /TiO 2 with visible radiation

  4. Core-concrete interactions with overlying water pools

    International Nuclear Information System (INIS)

    Blose, R.E.; Powers, D.A.; Copus, E.R.; Brockmann, J.E.; Simpson, R.B.; Lucero, D.A.

    1993-11-01

    The WETCOR-1 test of simultaneous interactions of a high-temperature melt with water and a limestone/common-sand concrete is described. The test used a 34.1-kg melt of 76.8 w/o Al 2 O 3 , 16.9 w/o CaO, and 4.0 w/o SiO 2 heated by induction using tungsten susceptors. Once quasi-steady attack on concrete by the melt was established, an attempt was made to quench the melt at 1850 K with 295 K water flowing at 57 liters per minute. Net power into the melt at the time of water addition was 0.61 ± 0.19 W/cm 3 . The test configuration used in the WETCOR-1 test was designed to delay melt freezing to the walls of the test fixture. This was done to test hypotheses concerning the inherent stability of crust formation when high-temperature melts are exposed to water. No instability in crust formation was observed. The flux of heat through the crust to the water pool maintained over the melt in the test was found to be 0.52 ± 0.13 MW/m 2 . Solidified crusts were found to attenuate aerosol emissions during the melt concrete interactions by factors of 1.3 to 3.5. The combination of a solidified crust and a 30-cm deep subcooled water pool was found to attenuate aerosol emissions by factors of 3 to 15

  5. Phase diagrams of KY(WO4)2-KEr(WO4)2, KGd(WO4)2-KEr(WO4)2 systems and single crystal growth for some tungstates

    International Nuclear Information System (INIS)

    Yudanova, L.I.; Pavlyuk, A.A.; Potapova, O.G.

    1992-01-01

    Phase diagrams of the KY(WO 4 ) 2 -KEr(WO 4 ) 2 , KGd(WO 4 ) 2 -KEr(WO 4 ) 2 systems were studied by differential thermal and X-ray diffraction analyses. Continuous variety of solid solutions are in the KY(WO 4 ) 2 -KEr(WO 4 ) 2 system. They occurred just as in the area of alphaso beta-modifications. Limited areas of the solid solutions based on components were in the KGd(WO 4 ) 2 -KEr(WO 4 ) 2 system. Monocrystals of potassium-yttrium and potassium-gadolinium tungstates activated by erbium were grown using modified low-gradient Czochralski method

  6. Synthesis, characterization and photocatalytic activity of WO{sub 3}/TiO{sub 2} for NO removal under UV and visible light irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Luévano-Hipólito, E. [CIIDIT, Facultad de Ingeniería Mecánica y Eléctrica, Universidad Autónoma de Nuevo León, Ciudad Universitaria, C.P. 66451 San Nicolás de los Garza, N.L. (Mexico); Martínez-de la Cruz, A., E-mail: azael.martinezdl@uanl.edu.mx [CIIDIT, Facultad de Ingeniería Mecánica y Eléctrica, Universidad Autónoma de Nuevo León, Ciudad Universitaria, C.P. 66451 San Nicolás de los Garza, N.L. (Mexico); López-Cuellar, E. [CIIDIT, Facultad de Ingeniería Mecánica y Eléctrica, Universidad Autónoma de Nuevo León, Ciudad Universitaria, C.P. 66451 San Nicolás de los Garza, N.L. (Mexico); Yu, Q.L.; Brouwers, H.J.H. [Department of the Built Environment, Eindhoven University of Technology, P.O. Box 513, 5600 MB Eindhoven (Netherlands)

    2014-11-14

    Samples with different proportions WO{sub 3}/TiO{sub 2} were prepared by co-precipitation method followed by a heat treatment. The samples were characterized by X-ray powder diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), diffuse reflectance spectroscopy (DRS), and adsorption–desorption N{sub 2} isotherms (BET). The photocatalytic properties of WO{sub 3}/TiO{sub 2} samples were evaluated in the photo-oxidation reaction of nitric oxide (NO) under UV and visible light irradiation. The highest photocatalytic activity was observed in the WO{sub 3}/TiO{sub 2} sample with a composition of 80% mole of TiO{sub 2}. Among the different substrates used for supporting the photocatalyst, the best results were reached over concrete and glass when it was exposed to UV and visible light irradiation, respectively. In overall, the photocatalytic efficiency of the synthesized materials was higher under UV than visible light irradiation. - Highlights: • WO{sub 3}/TiO{sub 2} prepared in simple way show high photocatalytic activity for NO removal. • The concrete was the best substrate to the performance of WO{sub 3}/TiO{sub 2} with UV radiation. • The glass was the best substrate to the performance of WO{sub 3}/TiO{sub 2} with visible radiation.

  7. Improved Charge Separation in WO3/CuWO4 Composite Photoanodes for Photoelectrochemical Water Oxidation

    Directory of Open Access Journals (Sweden)

    Danping Wang

    2016-05-01

    Full Text Available Porous tungsten oxide/copper tungstate (WO3/CuWO4 composite thin films were fabricated via a facile in situ conversion method, with a polymer templating strategy. Copper nitrate (Cu(NO32 solution with the copolymer surfactant Pluronic®F-127 (Sigma-Aldrich, St. Louis, MO, USA, generic name, poloxamer 407 was loaded onto WO3 substrates by programmed dip coating, followed by heat treatment in air at 550 °C. The Cu2+ reacted with the WO3 substrate to form the CuWO4 compound. The composite WO3/CuWO4 thin films demonstrated improved photoelectrochemical (PEC performance over WO3 and CuWO4 single phase photoanodes. The factors of light absorption and charge separation efficiency of the composite and two single phase films were investigated to understand the reasons for the PEC enhancement of WO3/CuWO4 composite thin films. The photocurrent was generated from water splitting as confirmed by hydrogen and oxygen gas evolution, and Faradic efficiency was calculated based on the amount of H2 produced. This work provides a low-cost and controllable method to prepare WO3-metal tungstate composite thin films, and also helps to deepen the understanding of charge transfer in WO3/CuWO4 heterojunction.

  8. Core-concrete interactions with overlying water pools. The WETCOR-1 test

    Energy Technology Data Exchange (ETDEWEB)

    Blose, R.E. [Ktech Corp., Albuquerque, NM (United States); Powers, D.A.; Copus, E.R.; Brockmann, J.E.; Simpson, R.B.; Lucero, D.A. [Sandia National Labs., Albuquerque, NM (United States)

    1993-11-01

    The WETCOR-1 test of simultaneous interactions of a high-temperature melt with water and a limestone/common-sand concrete is described. The test used a 34.1-kg melt of 76.8 w/o Al{sub 2}O{sub 3}, 16.9 w/o CaO, and 4.0 w/o SiO{sub 2} heated by induction using tungsten susceptors. Once quasi-steady attack on concrete by the melt was established, an attempt was made to quench the melt at 1850 K with 295 K water flowing at 57 liters per minute. Net power into the melt at the time of water addition was 0.61 {plus_minus} 0.19 W/cm{sup 3}. The test configuration used in the WETCOR-1 test was designed to delay melt freezing to the walls of the test fixture. This was done to test hypotheses concerning the inherent stability of crust formation when high-temperature melts are exposed to water. No instability in crust formation was observed. The flux of heat through the crust to the water pool maintained over the melt in the test was found to be 0.52 {plus_minus} 0.13 MW/m{sup 2}. Solidified crusts were found to attenuate aerosol emissions during the melt concrete interactions by factors of 1.3 to 3.5. The combination of a solidified crust and a 30-cm deep subcooled water pool was found to attenuate aerosol emissions by factors of 3 to 15.

  9. Microwave mediated synthesis of nanostructured Co -WO_3 and CoWO_4 for supercapacitor applications

    International Nuclear Information System (INIS)

    Dhilip Kumar, R.; Karuppuchamy, S.

    2016-01-01

    Co-WO_3 and CoWO_4 nanopowders have been successfully obtained from microwave mediated process. The characterization of the prepared nanopowders was carried out by X-ray diffraction (XRD), scanning electron microscopy and Energy dispersive X-ray spectroscopy techniques. The XRD pattern confirms the formation of orthorhombic and monoclinic phase of the as-synthesized and calcined samples, respectively. Scanning electron microscopic examination of the resultant powders reveals the formation of nanoporous morphology. The electrochemical performance of the Co-WO_3 and CoWO_4 coated electrodes was also investigated. The maximum specific capacitance of 45 F/g was achieved for the Co-WO_3 nanopowder. - Highlights: • Novel nano-sized Co-WO_3 and CoWO_4 materials have been prepared. • A new and simple solution growth technique was developed. • Co-WO_3 is a promising material for supercapacitor applications.

  10. Fabrication and characterization of WO3/Ag/WO3 multilayer transparent anode with solution-processed WO3 for polymer light-emitting diodes.

    Science.gov (United States)

    Jeon, Kangmin; Youn, Hongseok; Kim, Seongbeom; Shin, Seongbeom; Yang, Minyang

    2012-05-15

    The dielectric/metal/dielectric multilayer is suitable for a transparent electrode because of its high-optical and high-electrical properties; however, it is fabricated by an expensive and inefficient multistep vacuum process. We present a WO3/Ag/WO3 (WAW) multilayer transparent anode with solution-processed WO3 for polymer light-emitting diodes (PLEDs). This WAW multilayer not only has high transmittance and low resistance but also can be easily and rapidly fabricated. We devised a novel method to deposit a thin WO3 layer by a solution process in an air environment. A tungstic acid solution was prepared from an aqueous solution of Na2WO4 and then converted to WO3 nanoparticles (NPs) by a thermal treatment. Thin WO3 NP layers form WAW multilayer with a thermal-evaporated Ag layer, and they improve the transmittance of the WAW multilayer because of its high transmittance and refractive index. Moreover, the surface of the WO3 layer is homogeneous and flat with low roughness because of the WO3 NP generation from the tungstic acid solution without aggregation. We performed optical simulation and experiments, and the optimized WAW multilayer had a high transmittance of 85% with a sheet resistance of 4 Ω/sq. Finally, PLEDs based on the WAW multilayer anode achieved a maximum luminance of 35,550 cd/m2 at 8 V, and this result implies that the solution-processed WAW multilayer is appropriate for use as a transparent anode in PLEDs.

  11. Measurement of sediments thickness by ground penetrating radar; Denjihaho wo mochiita kotei taisekibutsu soatsu no sokutei

    Energy Technology Data Exchange (ETDEWEB)

    Nozawa, E [Tokyo Electric Power Co. Inc., Tokyo (Japan); Inagaki, M

    1997-05-27

    An attempt was made to measure thickness of a layer of reservoir bottom sediments by utilizing the electromagnetic reflection method. Because water is a substance difficult for electromagnetic waves to permeate, considerations were given on to suppress attenuation to a minimum, and improve receiving sensitivity. The test used monocycle pulses with a central frequency of 200 MHz. In order to generate stabilized pulses with little unnecessary reflection, an antenna as large as it can be fitted into a rubber boat was employed. In order to acquire referential data, the test was carried out by using simultaneously a sound wave exploration device. The lake at which the test was carried out is a regulating reservoir with a size of about 250 m {times} 150 m, with its bottom made of concrete slab. This means that the lake consists of a three-layer structure comprising water, soil deposits, and concrete bottom from the water surface. According to an example of acquired electromagnetic exploration records, boundary reflection of water and sediments was observed clearly at water depths of 2 to 3 m as a shallow portion and 5 to 6 m as a deep portion. Reflection between the sediments and the bottom plate was also observed sufficiently distinctly. 3 refs., 8 figs.

  12. In situ synthesis of CdS/CdWO4/WO3 heterojunction films with enhanced photoelectrochemical properties

    Science.gov (United States)

    Zhan, Faqi; Li, Jie; Li, Wenzhang; Yang, Yahui; Liu, Wenhua; Li, Yaomin

    2016-09-01

    CdS/CdWO4/WO3 heterojunction films on fluorine-doped tin oxide (FTO) substrates are for the first time prepared as an efficient photoanode for photoelectrochemical (PEC) hydrogen generation by an in situ conversion process. The samples are characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), ultraviolet visible spectrometry (UV-vis) and X-ray photoelectron spectroscopy (XPS). The CdS hollow spheres (∼80 nm) sensitized WO3 plate film with a CdWO4 buffer-layer exhibits increased visible light absorption and a significantly improved photoelectrochemical performance. The photocurrent density at 0 V (vs. Ag/AgCl) of the CdS/CdWO4/WO3 anode is ∼3 times higher than that of the CdWO4/WO3 anode, and ∼9 times higher than that of pure WO3 under illumination. The highest incident-photon-to-current-efficiency (IPCE) value increased from 16% to 63% when the ternary heterojunction was formed. This study demonstrates that the synthesis of ternary composite photocatalysts by the in situ conversion process may be a promising approach to achieve high photoelectric conversion efficiency.

  13. X-ray photoelectron spectroscopy study of BaWO{sub 4} and Ba{sub 2}CaWO{sub 6}

    Energy Technology Data Exchange (ETDEWEB)

    Capece, Angela M., E-mail: acapece@pppl.gov [California Institute of Technology, Pasadena, CA (United States); Polk, James E. [Jet Propulsion Laboratory, Pasadena, CA (United States); Shepherd, Joseph E. [California Institute of Technology, Pasadena, CA (United States)

    2014-12-15

    Highlights: • XPS reference spectra for Ba{sub 2}CaWO{sub 6} and BaWO{sub 4} are presented. • Binding energies of Ba 3d and W 4f lines are 0.7 eV higher for BaWO{sub 4} than Ba{sub 2}CaWO{sub 6}. • Ca 2p spectrum contains two sets of Ca 2p doublets attributed to Ba{sub 2}CaWO{sub 6} and CaCO{sub 3}. - Abstract: XPS reference spectra for Ba{sub 2}CaWO{sub 6} and BaWO{sub 4} are presented, including high resolution spectra of the Ba 3d, W 4f, C 1s, Ca 2p, and O 1s lines. The peak locations and full widths at half maximum are also given. The binding energies of the Ba 3d and W 4f lines are 0.7 eV higher for BaWO{sub 4} than for Ba{sub 2}CaWO{sub 6}. The Ca 2p spectrum contains two sets of Ca 2p doublets that were attributed to Ba{sub 2}CaWO{sub 6} and CaCO{sub 3}.

  14. In-situ transmission electron microscopy imaging of formation and evolution of LixWO3 during lithiation of WO3 nanowires

    International Nuclear Information System (INIS)

    Qi, Kuo; Li, Xiaomin; Sun, Muhua; Huang, Qianming; Wei, Jiake; Xu, Zhi; Wang, Wenlong; Bai, Xuedong; Wang, Enge

    2016-01-01

    The phase transition from monoclinic WO 3 to cubic Li x WO 3 during lithiation of WO 3 is one of the key features for tungsten oxide as the most used electrochromic material. Conventionally, the lithium intercalation of WO 3 has been studied by building generic layered electrochromic device combining with structural characterization and electrochemistry measurement at macro scale. In-situ transmission electron microscopy (in-situ TEM) has been proposed as a method for revealing the detailed mechanism of structural, physical, and chemical properties. Here, we use in-situ TEM method to investigate the formation and evolution of Li x WO 3 in real-time during the electrochemical lithiation of WO 3 nanowires. The dynamic lithiation process is recorded by TEM imaging, diffraction, and electron energy loss spectroscopy. The WO 3 -Li x WO 3 phase boundary of reaction front has been observed at high resolution. The timeliness of crystallinity of Li x WO 3 and the intercalation channels for Li ions are also identified. Moreover, the co-existence of both polycrystalline Li-poor area and amorphous Li-rich phases of Li x WO 3 was found. Our results provide an insight into the basic lithiation process of WO 3 , which is significantly important for understanding the electrochromic mechanism of tungsten oxide.

  15. Conduction and transport numbers in metacomposites MeWO4 · WO3 (Me = Ca, Sr, Ba)

    International Nuclear Information System (INIS)

    Nejman, A.Ya.; Pestereva, N.N.; Sharafutdinov, A.R.; Kostikov, Yu.P.

    2005-01-01

    The conductivity and transfer numbers of charge carriers for composites in the MeWO 4 -WO 3 (Me = Ca, Sr, Ba) systems are studied as a function of the temperature and the activity of oxygen in a gas phase. The transfer numbers are determined by the emf method and are estimated from dependences of conductivity on the activity of oxygen in a gas phase. The deficiencies of the given procedure as applied to investigation of properties of composite phases are analyzed. The materials under study are classified as metacomposites. The concentration intervals of the ionic, mixed, and electronic conductivities are determined. The conductivity of (100-x)MeWO 4 · xWO 3 composites is predominantly ionic at x ≤ 10 (Me = Ca), x ≤ 60 (Me = Sr), and x ≤ 45 (Me = Ba). The obtained data are explained in the framework of a model that represents a composite as a distributed matrix system where a film of surface phase MeW-s with a high mobility of oxygen ions plays the role of a connected matrix. It is presumed that the surface phase MeW-s possesses double-sided surface activity (α MeW-s ≤ α WO 3 , α MeWO 4 ) and a higher mobility with respect to MeWO 4 and WO 3 . The discovered anomalies of dependences σ O 2- (T) and partial conductivities σ O 2- , σ el (T) are explained by a change in the stoichiometry, morphology, and the degree of tie-up of surface phase MeW-s caused by a change in the temperature and composition of composites [ru

  16. Color landscape plan of the concrete Consideration on the harmony of concrete and landscape; Konkurito no shikisai keikan keikaku. Keikan to konkurito no chowa wo kangaeru

    Energy Technology Data Exchange (ETDEWEB)

    Akiyama, Hiroshi [Landscape Planning and Design with Concrete and Color, Tokyo (Japan)

    1999-03-10

    In Ministry of Construction, they positively promote the natural river make, and they have announced the basic design with the aim of river which does not use the concrete and river in which the concrete is not seen. It is the design control in using the concrete to be necessary for this. They introduced color landscape plan of the pile block of the concrete as a case in aiming at the harmony of concrete and landscape of being more concrete. They introduced concrete product which could express the local color characteristics of colors of the concrete which it does not suit for the landscape, usage of the concrete, concrete of the warm color, colors of concrete product of France, examples of the Disneyland, colors concrete lied, landscapes and cost, etc. (NEDO)

  17. Anti-tumor activity of self-charged (Eu,Ca):WO3 and Eu:CaWO4 nanoparticles

    International Nuclear Information System (INIS)

    Lin, Cao; Cong, Wang; De'An, Pan; Jiexin, Cao; Ping, Che; Volinsky, Alex A.

    2012-01-01

    Non-stoichiometric (Eu,Ca):WO 3 and Eu:CaWO 4 nanoparticles with anti-tumor activity are synthesized in a sol-gel method by adding excessive Eu 3+ and Ca 2+ ions to tungsten oxide crystal structure. Colorimetric assay shows that 10 nm (Eu,Ca):WO 3 and Eu:CaWO 4 nanoparticles can effectively inhibit growth of mammary cancer cells without any harm to normal cells. Nanoparticles are characterized by X-ray diffraction, high resolution transmission electron microscopy and fluorescence optical spectrometry. Nanomaterials, insoluble in synthesized water, have complicated self-charging surfaces that trap mammary cancer cells. Surface self-charging effect is suggested as the inhibition mechanism. (author)

  18. Preparation and characterization of WO{sub 3} nanoparticles, WO{sub 3}/TiO{sub 2} core/shell nanocomposites and PEDOT:PSS/WO{sub 3} composite thin films for photocatalytic and electrochromic applications

    Energy Technology Data Exchange (ETDEWEB)

    Boyadjiev, Stefan I., E-mail: boiajiev@gmail.com [MTA-BME Technical Analytical Chemistry Research Group, Szent Gellért tér 4, Budapest, H-1111 (Hungary); Santos, Gustavo dos Lopes; Szűcs, Júlia [Budapest University of Technology and Economics, Department of Inorganic and Analytical Chemistry, Szent Gellért tér 4, Budapest, H-1111 (Hungary); Szilágyi, Imre M., E-mail: imre.szilagyi@mail.bme.hu [MTA-BME Technical Analytical Chemistry Research Group, Szent Gellért tér 4, Budapest, H-1111 (Hungary); Budapest University of Technology and Economics, Department of Inorganic and Analytical Chemistry, Szent Gellért tér 4, Budapest, H-1111 (Hungary)

    2016-03-25

    In this study, monoclinic WO{sub 3} nanoparticles were obtained by thermal decomposition of (NH{sub 4}){sub x}WO{sub 3} in air at 600 °C. On them by atomic layer deposition (ALD) TiO{sub 2} films were deposited, and thus core/shell WO{sub 3}/TiO{sub 2} nanocomposites were prepared. We prepared composites of WO{sub 3} nanoparticles with conductive polymer as PEDOT:PSS, and deposited thin films of them on glass and ITO substrates by spin coating. The formation, morphology, composition and structure of the as-prepared pure and composite nanoparticles, as well thin films, were studied by TEM, SEM-EDX and XRD. The photocatalytic activity of both the WO{sub 3} and core/shell WO{sub 3}/TiO{sub 2} nanoparticles was studied by decomposing methyl orange in aqueous solution under UV light irradiation. Cyclic voltammetry measurements were performed on the composite PEDOT:PSS/WO{sub 3} thin films, and the coloring and bleaching states were studied.

  19. Preparation of spherical fine particulate pigments within water-in-oil emulsions and their properties. (II). ; Formation mechanism and characteristic of spherical fine particulate pigment of tartrazine. W/O emulsion wo mochiita kyujo biryushi ganryo no chosei to seishitsu(dai 2 ho). ; Kiiro 4 go kyujo biryushi ganryo no seisei kiko to tokusei

    Energy Technology Data Exchange (ETDEWEB)

    Imai, T.; Iwano, K.; Hotta, H.; Takano, S.; Tsutsumi, H. (Kao Corporation, Tokyo (Japan))

    1991-12-20

    The previous report explained that an excellent spherical particulate pigment with a grain size of 0.5 mm or less can be obtained by preparing multinuclear aluminum lakes from acidic dyes and multinuclear aluminum salt using water droplets in a W/O emulsion as reaction fields. This paper describes preparing pigments varying the charging concentrations of the pigments in a W/O emulsion and the droplet particle size to discuss the mechanism of forming the pigments. As a result, it was found that the particle sizes in the produced pigments have a clear correlation with the charging concentrations of the pigments and the droplet particle sizes in the W/O emulsion. A pigment produced in the W/O emulsion forms only in its own droplets, and reflects its particle sizes. Films dispersed with pigments having different particle sizes were prepared to discuss their tinting abilities, whereas it was clarified that the smaller the particle size, the higher the tinting ability and the higher saturation in colored paint films. 6 refs., 9 figs., 3 tabs.

  20. Photocatalytic properties of h-WO{sub 3} nanoparticles obtained by annealing and h-WO{sub 3} nanorods prepared by hydrothermal method

    Energy Technology Data Exchange (ETDEWEB)

    Boyadjiev, Stefan I., E-mail: boiajiev@gmail.com [MTA-BME Technical Analytical Chemistry Research Group, Szent Gellért tér 4, Budapest, H-1111 (Hungary); Nagy-Kovács, Teodóra [Budapest University of Technology and Economics, Department of Inorganic and Analytical Chemistry, Szent Gellért tér 4, Budapest, H-1111 (Hungary); Lukács, István [Hungarian Academy of Sciences, Research Centre for Energy, Institute of Technical Physics and Materials Science, H-1121 Budapest, Konkoly Thege M. út 29-33 (Hungary); Szilágyi, Imre M., E-mail: imre.szilagyi@mail.bme.hu [MTA-BME Technical Analytical Chemistry Research Group, Szent Gellért tér 4, Budapest, H-1111 (Hungary); Budapest University of Technology and Economics, Department of Inorganic and Analytical Chemistry, Szent Gellért tér 4, Budapest, H-1111 (Hungary)

    2016-03-25

    In the present study, two different methods for preparing hexagonal WO{sub 3} (h-WO{sub 3}) photocatalysts were used - controlled thermal decomposition and hydrothermal synthesis. WO{sub 3} nanoparticles with hexagonal structure were obtained by annealing (NH{sub 4}){sub x}WO{sub 3-y} at 500 °C in air. WO{sub 3} nanorods were prepared by a hydrothermal method using sodium tungstate Na{sub 2}WO{sub 4}, HCl, (COOH){sub 2} and NaSO{sub 4} precursors at 200 °C. The formation, morphology, structure and composition of the as-prepared nanoparticles and nanorods were studied by powder X-ray diffraction (XRD), transmission electron microscopy (TEM), and scanning electron microscopy combined with energy-dispersive X-ray spectroscopy (SEM-EDX). The photocatalytic activity of the h-WO{sub 3} nanoparticles and nanorods was studied by decomposing methyl orange in aqueous solution under UV light irradiation.

  1. Tuning the pure monoclinic phase of WO3 and WO3-Ag nanostructures for non-enzymatic glucose sensing application with theoretical insight from electronic structure simulations

    Science.gov (United States)

    Ponnusamy, Rajeswari; Gangan, Abhijeet; Chakraborty, Brahmananda; Sekhar Rout, Chandra

    2018-01-01

    Here, we report the controlled hydrothermal synthesis and tuning of the pure monoclinic phase of WO3 and WO3-Ag nanostructures. Comparative electrochemical nonenzymatic glucose sensing properties of WO3 and WO3-Ag were investigated by cyclic voltammetry and chronoamperometric tests. We observed enhanced glucose sensing performance of WO3-Ag porous spheres as compared to bare WO3 nanoslabs. The sensitivity of the pure WO3 nanoslabs is 11.1 μA μM-1 cm-2 whereas WO3-Ag porous spheres exhibit sensitivity of 23.3 μA μM-1 cm-2. The WO3-Ag porous spheres exhibited a good linear range (5-375 μM) with excellent anti-interference property. Our experimental observations are qualitatively supported by density functional theory simulations through investigation of bonding and charge transfer mechanism of glucose on WO3 and Ag doped WO3. As the binding energy of glucose is more on the Ag doped WO3 (100) surface compared to the bare WO3 (100) surface and the Ag doped WO3 (100) surface becomes more conducting due to enhancement of density of states near the Fermi level, we can infer that Ag doped WO3 exhibits a better charge transfer media compared to bare WO3 resulting in enhanced glucose sensitivity in consistency with our experimental data.

  2. The social nature of environmental knowledge among the nomadic WoÉ - aaÉ"e of Niger

    Directory of Open Access Journals (Sweden)

    Nikolaus Schareika

    2014-12-01

    Full Text Available Pastoral nomads such as West Africa's WoÉ - aaÉ"e are renowned for the impressive environmental knowledge they apply to successfully raise animal herds in arid and variable environments. We looked at such herders' knowledge not as based on individual learning and expertise but as ultimately social in the sense that it is formed, made available, and linked to pastoral decision making in the public and interactive space of permanent talking, discussing, and negotiating among peers. Drawing on theoretical ideas from science and technology studies, a number of concrete social situations of information management and pastoral decision making were explored in detail to reveal the distinctly social character of WoÉ - aaÉ"e knowledge. Special emphasis has been given to the institutional framework of knowledge exchange; the blending of moral values and empirical facts in particular statements of knowledge; the dialogic and collaborative nature of information procurement and assessment; and the contingency of decisions reached after lengthy rounds of discussion among herders.

  3. Nonlinear current-voltage characteristics of WO3-x nano-/micro-rods

    Science.gov (United States)

    Shen, Zhenguang; Peng, Zhijian; Zhao, Zengying; Fu, Xiuli

    2018-04-01

    A series of crystalline tungsten oxide nano-/micro-rods with different compositions of WO3, WO2.90, W19O55 (WO2.89) and W18O49 (WO2.72) but identical morphology feature were first prepared. Then, various nanoscaled electrical devices were fabricated from them by micro-fabrication through a focused ion beam technique. Interestingly, the devices from the oxygen-deficient WO3-x display significantly nonlinear current-voltage characteristics. The calculated nonlinear coefficients of the WO2.90, WO2.83, and WO2.72 varistors are 2.52, 3.32 and 4.91, respectively. The breakdown voltage of the WO2.90, WO2.83, and WO2.72 varistors are 1.93, 1.28 and 0.93 V, respectively. Such WO3-x nano-varistors might be promising for low-voltage electrical/electronic devices.

  4. A study of electron excitations in CaWO sub 4 and PbWO sub 4 single crystals

    CERN Document Server

    Muerk, V; Mihoková, E; Nitsch, K

    1997-01-01

    The excitation spectra of photo- and thermo-luminescence were compared in the VUV-UV spectral region in CaWO sub 4 and PbWO sub 4 scheelite tungstates. Temperature dependences of emission intensities and decay times were measured for PbWO sub 4 in the 80-300 K range and approximated by a simple phenomenological model. The energy level structure of the emission centre excited state and related kinetic processes are discussed for both tungstates. (author)

  5. Photoluminescence in solid solutions and thin films of tungstates CaWO{sub 4}-CdWO{sub 4}

    Energy Technology Data Exchange (ETDEWEB)

    Taoufyq, A.; Mauroy, V.; Guinneton, F.; Valmalette, J-C. [University of Toulon, IM2NP, UMR CNRS 7334, La Garde, (France); Fiorido, T. [Aix Marseille University, IM2NP, UMR CNRS, 7334, Marseille, (France); Benlhachemi, A. [IBN ZOHR University, Faculty of sciences, Environment and Materials Laboratory, Agadir, (Morocco); Lyoussi, A. [CEA of Cadarache, DEN, Departement of reactors studies, experimental physics, Instrumentation Sensors and Dosimetry Laboratory, (France); Nolibe, G. [Cesigma society, signals and systems, La Garde, (France); Gavarri, J-R. [University of Toulon, IM2NP, UMR CNRS 7334, La Garde, (France)

    2015-07-01

    In this study, we present two types of studies on the luminescence properties under UV and X-ray excitations of solid solutions Ca{sub 1-x}Cd{sub x}WO{sub 4} and of thin layers of CaWO{sub 4} and CdWO{sub 4}. These tungstate based solid solutions are susceptible to be integrated into new radiation sensors, in order to be used in different fields of applications such as reactor measurements, safeguards, homeland security, nuclear nondestructive assays, LINAC emission radiation measurement. However these complex materials were rarely investigated in the literature. One first objective of our studies was to establish correlations between luminescence efficiency, chemical substitution and the degree of crystallization resulting from elaboration conditions. A second objective will be to determine the efficiency of luminescence properties of thin layers of these materials. In the present work, we focus our attention on the role of chemical substitution on photon emissions under UV and X-ray irradiations. The luminescence spectra of Ca{sub 1-x}Cd{sub x}WO{sub 4} polycrystalline materials have been investigated at room temperature as a function of composition (0≤x≤1). In addition, we present a preliminary study of the luminescence of CaWO{sub 4} and CdWO{sub 4} thin layers: oscillations observed in the case of X-ray excitations in the luminescence spectra are discussed. (authors)

  6. Development of an antimicrobial concrete to inhibiting corrosion; Konkurito wo fushoku kara gado suru kokin konkurito no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Kurihara, Y.

    1999-11-10

    It has been clarified that the corrosion of concrete in sewage facilities is caused by the action of specific microorganism. The corrosion of concrete is caused by the complicate interaction of chemical substances and microorganisms existing in sewage water. As microorganisms related to this phenomenon, lead sulfate reductase and sulfur oxidase are well known. This paper introduces antimicrobials for concrete using zeolite as a main component and a concrete containing these antimicrobials, which were developed for killing or suppressing the generation of these microorganisms causing the corrosion of concrete. The sales results during 2 years since the start of the sales in May 1997 was 16 tons for antimicrobials including zeolite-supported silver - copper catalyst, and 8,138 tons for antimicrobial concrete. Sixty-eight companies have organized concrete workshop>, which will promote the popularization and technical guidance of antimicrobial concrete. (NEDO)

  7. Photocatalytic activity of Bi_2WO_6/Bi_2S_3 heterojunctions: the facilitation of exposed facets of Bi_2WO_6 substrate

    International Nuclear Information System (INIS)

    Yan, Long; Wang, Yufei; Shen, Huidong; Zhang, Yu; Li, Jian; Wang, Danjun

    2017-01-01

    Highlights: • Bi_2S_3/Bi_2WO_6 hybrids with exposed (020) Bi_2WO_6 facets have been synthesized. • X-ray photoelectron spectroscopy reveals that a small amount of Bi_2S_3 was formed. • The enhanced photoactivity of hybrids is due to heterojunction and (020) facets. • A possible photocatalytic degradation mechanism is proposed. - Abstract: Bi_2S_3/Bi_2WO_6 hybrid architectures with exposed (020) Bi_2WO_6 facets have been synthesized via a controlled anion exchange approach. X-ray photoelectron spectroscopy (XPS) reveals that a small amount of Bi_2S_3 was formed on the surface of Bi_2WO_6 during the anion exchange process, thus leading to the transformation from the Bi_2WO_6 to Bi_2S_3/Bi_2WO_6. A rhodamine B (RhB) aqueous solution was chosen as model organic pollutants to evaluate the photocatalytic activities of the Bi_2S_3/Bi_2WO_6 catalysts. Under visible light irradiation, the Bi_2S_3/Bi_2WO_6-TAA displayed the excellent visible light photoactivities compared with pure Bi_2S_3, Bi_2WO_6 and other composite photocatalysts. The efficient photocatalytic activity of the Bi_2S_3/Bi_2WO_6-TAA composite microspheres was ascribed to the constructed heterojunctions and the inner electric field caused by the exposed (020) Bi_2WO_6 facets. Active species trapping experiments revealed that h"+ and O_2·"− are the main active species in the photocatalytic process. Furthermore, the as-obtained photocatalysts showed good photocatalytic activity after four recycles. The results presented in this study provide a new concept for the rational design and development of highly efficient photocatalysts.

  8. New seismic source `BLASTER` for seismic survey; Hasaiyaku wo shingen to shite mochiita danseiha tansa

    Energy Technology Data Exchange (ETDEWEB)

    Koike, G; Yoshikuni, Y [OYO Corp., Tokyo (Japan)

    1996-10-01

    Built-up weight and vacuole have been conceived as seismic sources without using explosive. There have been problems that they have smaller energy to generate elastic wave than explosive, and that they have inferior working performance. Concrete crushing explosive is tried to use as a new seismic source. It is considered to possess rather large seismic generating energy, and it is easy to handle from the viewpoint of safety. Performance as seismic source and applicability to exploration works of this crushing explosive were compared with four kinds of seismic sources using dynamite, dropping weight, shot-pipe utilizing shot vacuole, and impact by wooden maul. When considered by the velocity amplitude, the seismic generating energy of the crushing explosive of 120 g is about one-fifth of dynamite of 100 g. Elastic wave generated includes less high frequency component than that by dynamite, and similar to that using seismic source without explosive, such as the weight dropping. The maximum seismic receiving distance obtained by the seismic generation was about 100 m. This was effective for the slope survey with the exploration depth between 20 m and 30 m. 1 ref., 9 figs., 2 tabs.

  9. Detection and phylogenetic analysis of bacteriophage WO in spiders (Araneae).

    Science.gov (United States)

    Yan, Qian; Qiao, Huping; Gao, Jin; Yun, Yueli; Liu, Fengxiang; Peng, Yu

    2015-11-01

    Phage WO is a bacteriophage found in Wolbachia. Herein, we represent the first phylogenetic study of WOs that infect spiders (Araneae). Seven species of spiders (Araneus alternidens, Nephila clavata, Hylyphantes graminicola, Prosoponoides sinensis, Pholcus crypticolens, Coleosoma octomaculatum, and Nurscia albofasciata) from six families were infected by Wolbachia and WO, followed by comprehensive sequence analysis. Interestingly, WO could be only detected Wolbachia-infected spiders. The relative infection rates of those seven species of spiders were 75, 100, 88.9, 100, 62.5, 72.7, and 100 %, respectively. Our results indicated that both Wolbachia and WO were found in three different body parts of N. clavata, and WO could be passed to the next generation of H. graminicola by vertical transmission. There were three different sequences for WO infected in A. alternidens and two different WO sequences from C. octomaculatum. Only one sequence of WO was found for the other five species of spiders. The discovered sequence of WO ranged from 239 to 311 bp. Phylogenetic tree was generated using maximum likelihood (ML) based on the orf7 gene sequences. According to the phylogenetic tree, WOs in N. clavata and H. graminicola were clustered in the same group. WOs from A. alternidens (WAlt1) and C. octomaculatum (WOct2) were closely related to another clade, whereas WO in P. sinensis was classified as a sole cluster.

  10. Shielding properties of the ordinary concrete loaded with micro- and nano-particles against neutron and gamma radiations.

    Science.gov (United States)

    Mesbahi, Asghar; Ghiasi, Hosein

    2018-06-01

    The shielding properties of ordinary concrete doped with some micro and nano scaled materials were studied in the current study. Narrow beam geometry was simulated using MCNPX Monte Carlo code and the mass attenuation coefficient of ordinary concrete doped with PbO 2 , Fe 2 O 3 , WO 3 and H 4 B (Boronium) in both nano and micro scales was calculated for photon and neutron beams. Mono-energetic beams of neutrons (100-3000 keV) and photons (142-1250 keV) were used for calculations. The concrete doped with nano-sized particles showed higher neutron removal cross section (7%) and photon attenuation coefficient (8%) relative to micro-particles. Application of nano-sized material in the composition of new concretes for dual protection against neutrons and photons are recommended. For further studies, the calculation of attenuation coefficients of these nano-concretes against higher energies of neutrons and photons and different particles are suggested. Copyright © 2018 Elsevier Ltd. All rights reserved.

  11. Structure and photocatalytic performance of layered HNbWO6 nanosheet aggregation

    KAUST Repository

    Hu, Li-Fang

    2015-12-10

    Layered HNbWO6HNbWO6 nanosheet aggregation (e-HNbWO6e-HNbWO6) has been assembled by HNbWO6HNbWO6 nanosheet via an exfoliation-restaking route. The as-prepared samples are characterized by means of powder x-ray diffraction, scanning electron microscope, high-resolution transmission electron microscopy, laser Raman spectroscopy, ultraviolet-vis diffuse reflectance spectroscopy, and N2N2 adsorption-desorption isotherms. The photocatalytic performances of the as-prepared samples are evaluated by degradation of methylene blue (MB). The results revealed that e-HNbWO6e-HNbWO6 has a specific surface area of about 156.5  m2 g−1156.5  m2 g−1, and exhibits a relatively excellent photocatalytic performance for degradation of MB under UV light.

  12. Structure and photocatalytic performance of layered HNbWO6 nanosheet aggregation

    KAUST Repository

    Hu, Li-Fang; Li, Rui; He, Jie; Da, Liang-guo; Lv, Wei; Hu, Jin-song

    2015-01-01

    Layered HNbWO6HNbWO6 nanosheet aggregation (e-HNbWO6e-HNbWO6) has been assembled by HNbWO6HNbWO6 nanosheet via an exfoliation-restaking route. The as-prepared samples are characterized by means of powder x-ray diffraction, scanning electron microscope, high-resolution transmission electron microscopy, laser Raman spectroscopy, ultraviolet-vis diffuse reflectance spectroscopy, and N2N2 adsorption-desorption isotherms. The photocatalytic performances of the as-prepared samples are evaluated by degradation of methylene blue (MB). The results revealed that e-HNbWO6e-HNbWO6 has a specific surface area of about 156.5  m2 g−1156.5  m2 g−1, and exhibits a relatively excellent photocatalytic performance for degradation of MB under UV light.

  13. WO3 nano-ribbons: their phase transformation from tungstite (WO3·H2O) to tungsten oxide (WO3)

    DEFF Research Database (Denmark)

    Ahmadi, Majid; Sahoo, Satyaprakash; Younesi, Reza

    2014-01-01

    Tungsten oxide (WO3) nano-ribbons (NRs) were obtained by annealing tungstite (WO3·H2O) NRs. The latter was synthesized below room temperature using a simple, environmentally benign, and low cost aging treatment of precursors made by adding hydrochloric acid to diluted sodium tungstate solutions (...

  14. Synthesis, Characterization, and Gas Sensing Applications of WO3 Nanobricks

    Science.gov (United States)

    Xiao, Jingkun; Song, Chengwen; Dong, Wei; Li, Chen; Yin, Yanyan; Zhang, Xiaoni; Song, Mingyan

    2015-08-01

    WO3 nanobricks are fabricated by a simple hydrothermal method. Morphology and structure of the WO3 nanobricks are characterized by scanning electron microscopy and x-ray diffraction. Gas sensing properties of the as-prepared WO3 sensor are systematically investigated by a static gas sensing system. The results show that the WO3 nanobricks with defect corners demonstrate good crystallinity, and the mean edge length and wall thickness are 1-1.5 and 400 nm, respectively. The WO3 sensor achieves its maximum sensitivity to 100 ppm ethanol at the optimal operating temperature of 300 °C. Ultra-fast response time (2-3 s) and fast recovery time (4-11 s) of the WO3 sensor toward 100 ppm ethanol are also observed at this optimal operating temperature. Moreover, the WO3 sensor exhibits high selectivity to other gases such as methanol, benzene, hexane, and dichloromethane, indicating its excellent potential application as a gas sensor for ethanol detection.

  15. Fungus mediated biosynthesis of WO3 nanoparticles using Fusarium solani extract

    Science.gov (United States)

    Kavitha, N. S.; Venkatesh, K. S.; Palani, N. S.; Ilangovan, R.

    2017-05-01

    Currently nanoparticles were synthesized by emphasis bioremediation process due to less hazardous, eco-friendly and imperative applications on biogenic process. Fungus mediated biosynthesis strategy has been developed to prepare tungsten oxide nanoflakes (WO3, NFs) using the plant pathogenic fungus F.solani. The powder XRD pattern revealed the monoclinic crystal structure with improved crystalline nature of the synthesized WO3 nanoparticles. FESEM images showed the flake-like morphology of WO3, with average thickness and length around 40 nm and 300 nm respectively. The Raman spectrum of WO3 NFs showed their characteristic vibration modes that revealed the defect free nature of the WO3 NFs. Further, the elemental analysis indicated the stoichiometric composition of WO3 phase.

  16. The enhanced alcohol-sensing response of ultrathin WO3 nanoplates

    International Nuclear Information System (INIS)

    Chen Deliang; Hou Xianxiang; Wen Hejing; Wang Yu; Wang Hailong; Zhang Rui; Lu Hongxia; Xu Hongliang; Guan Shaokang; Li Xinjian; Sun Jing; Gao Lian

    2010-01-01

    Chemical sensors based on semiconducting metal oxide nanocrystals are of academic and practical significance in industrial processing and environment-related applications. Novel alcohol response sensors using two-dimensional WO 3 nanoplates as active elements have been investigated in this paper. Single-crystalline WO 3 nanoplates were synthesized through a topochemical approach on the basis of intercalation chemistry (Chen et al 2008 Small 4 1813). The as-obtained WO 3 nanoplate pastes were coated on the surface of an Al 2 O 3 ceramic microtube with four Pt electrodes to measure their alcohol-sensing properties. The results show that the WO 3 nanoplate sensors are highly sensitive to alcohols (e.g., methanol, ethanol, isopropanol and butanol) at moderate operating temperatures (260-360 deg. C). For butanol, the WO 3 nanoplate sensors have a sensitivity of 31 at 2 ppm and 161 at 100 ppm, operating at 300 deg. C. For other alcohols, WO 3 nanoplate sensors also show high sensitivities: 33 for methanol at 300 ppm, 70 for ethanol at 200 ppm, and 75 for isopropanol at 200 ppm. The response and recovery times of the WO 3 nanoplate sensors are less than 15 s for all the test alcohols. A good linear relationship between the sensitivity and alcohol concentrations has been observed in the range of 2-300 ppm, whereas the WO 3 nanoparticle sensors have not shown such a linear relationship. The sensitivities of the WO 3 nanoplate sensors decrease and their response times become short when the operating temperatures increase. The enhanced alcohol-sensing performance could be attributed to the ultrathin platelike morphology, the high crystallinity and the loosely assembling structure of the WO 3 nanoplates, due to the advantages of the effective adsorption and rapid diffusion of the alcohol molecules.

  17. Faster response of NO2 sensing in graphene–WO3 nanocomposites

    International Nuclear Information System (INIS)

    Srivastava, Shubhda; Jain, Kiran; Gupta, Govind; Senguttuvan, T D; Singh, V N; Singh, Sukhvir; Vijayan, N; Dilawar, Nita

    2012-01-01

    Graphene-based nanocomposites have proven to be very promising materials for gas sensing applications. In this paper, we present a general approach for the preparation of graphene–WO 3 nanocomposites. Graphene–WO 3 nanocomposite thin-layer sensors were prepared by drop coating the dispersed solution onto the alumina substrate. These nanocomposites were used for the detection of NO 2 for the first time. TEM micrographs revealed that WO 3 nanoparticles were well distributed on graphene nanosheets. Three different compositions (0.2, 0.5 and 0.1 wt%) of graphene with WO 3 were used for the gas sensing measurements. It was observed that the sensor response to NO 2 increased nearly three times in the case of graphene–WO 3 nanocomposite layer as compared to a pure WO 3 layer at room temperature. The best response of the graphene–WO 3 nanocomposite was obtained at 250 °C. (paper)

  18. CdWO4 polymorphs: Selective preparation, electronic structures, and photocatalytic activities

    International Nuclear Information System (INIS)

    Yan, Tingjiang; Li, Liping; Tong, Wenming; Zheng, Jing; Wang, Yunjian; Li, Guangshe

    2011-01-01

    This work explored the selective synthesis of polymorphs of CdWO 4 in either tetragonal or monoclinic phase by optimizing the experimental parameters. Systematic characterization indicated that both polymorphs possessed similar spherical morphologies but different structural building blocks. Electronic structures calculations for both polymorphs demonstrated the same constructions of conduction band or valence band, while the conduction band widths of both polymorphs were quite different. Both CdWO 4 polymorphs exhibited good photocatalytic activity for degradation of methyl orange under UV light irradiation. When comparing to some other well-known tungstate oxide materials, the photocatalytic activity was found to follow such a consequence, monoclinic CdWO 4 ∼monoclinic ZnWO 4 >tetragonal CdWO 4 >tetragonal CaWO 4 . The specific photocatalytic activity of monoclinic CdWO 4 was even higher than that of commercial TiO 2 photocatalyst (Degussa P25). The increased activity from the tetragonal CdWO 4 to the monoclinic was consistent with the trend of the decreased symmetry, and this could be explained in terms of the geometric structures and electronic structures for both polymorphs. -- Graphical abstract: Monoclinic CdWO 4 exhibited a much higher photocatalytic activity than the tetragonal form owing to the lower symmetry, more distorted geometric structure, and the dispersive band configuration. Display Omitted Research highlights: → Polymorphs of CdWO 4 in either tetragonal or monoclinic phase were selectively synthesized. → Both polymorphs possessed similar spherical morphologies, while the relevant structural building blocks were different. → Photocatalytic activities of CdWO 4 polymorphs depended strongly on the symmetry, geometric structure, as well as band configuration.

  19. An ultraviolet photodetector fabricated from WO3 nanodiscs/reduced graphene oxide composite material

    International Nuclear Information System (INIS)

    Shao Dali; Sawyer, Shayla; Yu Mingpeng; Lian Jie

    2013-01-01

    A high sensitivity, fast ultraviolet (UV) photodetector was fabricated from WO 3 nanodiscs (NDs)/reduced graphene oxide (RGO) composite material. The WO 3 NDs/reduced GO composite material was synthesized using a facile three-step synthesis procedure. First, the Na 2 WO 4 /GO precursor was synthesized by homogeneous precipitation. Second, the Na 2 WO 4 /GO precursor was transformed into H 2 WO 4 /GO composites by acidification. Finally, the H 2 WO 4 /GO composites were reduced to WO 3 NDs/RGO via a hydrothermal reduction process. The UV photodetector showed a fast transient response and high responsivity, which are attributed to the improved carrier transport and collection efficiency through graphene. The excellent material properties of the WO 3 NDs/RGO composite demonstrated in this work may open up new possibilities for using WO 3 NDs/RGO for future optoelectronic applications. (paper)

  20. Electrochemical Behavior of TiO2 Nanoparticle Doped WO3 Thin Films

    Directory of Open Access Journals (Sweden)

    Suvarna R. Bathe

    2014-01-01

    Full Text Available Nanoparticle TiO2 doped WO3 thin films by pulsed spray pyrolysis technique have been studied on fluorine tin doped (FTO and glass substrate. XRD shows amorphous nature for undoped and anatase phase of TiO2 having (101 plane for nanoparticle TiO2 doped WO3 thin film. SEM shows microfibrous reticulated porous network for WO3 with 600 nm fiber diameter and nanocrystalline having size 40 nm for TiO2 nanoparticle doped WO3 thin film. TiO2 nanoparticle doped WO3 thin film shows ~95% reversibility due to may be attributed to nanocrystalline nature of the film, which helpful for charge insertion and deinsertion process. The diffusion coefficient for TiO2 nanoparticle doped WO3 film is less than undoped WO3.

  1. WO{sub 3} nanorods prepared by low-temperature seeded growth hydrothermal reaction

    Energy Technology Data Exchange (ETDEWEB)

    Ng, Chai Yan [School of Materials and Mineral Resources Engineering, Universiti Sains Malaysia, 14300 Nibong Tebal, Penang (Malaysia); Abdul Razak, Khairunisak, E-mail: khairunisak@eng.usm.my [School of Materials and Mineral Resources Engineering, Universiti Sains Malaysia, 14300 Nibong Tebal, Penang (Malaysia); NanoBiotechnology Research and Innovation (NanoBRI), Institute for Research in Molecular Medicine (INFORMM), Universiti Sains Malaysia, 11800 USM, Penang (Malaysia); Lockman, Zainovia, E-mail: zainovia@eng.usm.my [School of Materials and Mineral Resources Engineering, Universiti Sains Malaysia, 14300 Nibong Tebal, Penang (Malaysia)

    2014-03-05

    Highlights: • WO{sub 3} nanorods with 5–10 nm diameter were grown directly on seeded tungsten foil. • WO{sub 3} nanorods were successfully grown at low temperature of 80 °C. • WO{sub 3} nanorods were grown on the entire surface of the seed layer after 24 h. • Annealed nanorods showed better electrochromic properties than as-made nanorods. -- Abstract: This work describes the first tungsten oxide (WO{sub 3}) nanorods hydrothermally grown on W foil. WO{sub 3} nanorods were successfully grown at low hydrothermal temperature of 80 °C by seeded growth hydrothermal reaction. The seed layer was prepared by thermally oxidized the W foil at 400 °C for 0.5 h. This work discusses the effect of hydrothermal reaction and annealing period on the morphological, structural, and electrochromic properties of WO{sub 3} nanorods. Various hydrothermal reaction periods (8–24 h) were studied. Monoclinic WO{sub 3} nanorods with 5–10 nm diameter were obtained after hydrothermal reaction for 24 h. These 24 h WO{sub 3} nanorods were also annealed at 400 °C with varying dwelling periods (0.5–4 h). Electrochromic properties of WO{sub 3} nanorods in an acidic electrolyte were analyzed using cyclic voltammetry and UV–vis spectrophotometry. WO{sub 3} nanorods annealed at 400 °C for 1 h showed the highest charge capacity and the largest optical contrast among the 24 h WO{sub 3} films. The sample also showed good cycling stability without significant degradation. Based on the results, the reaction mechanism of WO{sub 3} nanorod formation on W foil was proposed.

  2. Chemical purification of CaCO{sub 3} and CaWO{sub 4} powders used for CaWO{sub 4} crystal production for the CRESST experiment

    Energy Technology Data Exchange (ETDEWEB)

    Trinh Thi, H.H.; Defay, X.; Erb, A.; Hampf, R.; Lanfranchi, J.C.; Langenkaemper, A.; Morgalyuk, V.; Muenster, A.; Mondragon, E.; Oppenheimer, C.; Potzel, W.; Schoenert, S.; Steiger, H.; Ulrich, A.; Wawoczny, S.; Willers, M.; Zoeller, A. [Physik-Department and Excellence Cluster Universe, Technische Universitaet Muenchen, Garching (Germany)

    2016-07-01

    CRESST (Cryogenic Rare Event Search with Superconducting Thermometers) uses CaWO{sub 4} single crystals as targets for the direct search for dark matter particles. Since several years these CaWO{sub 4} crystals are grown at the Technische Universitaet Muenchen. Thereby, commercially available CaCO{sub 3} and WO{sub 3} powders are used for the synthesis of CaWO{sub 4} powder. For the experiment low intrinsic contaminations of the crystals play a crucial role. In order to improve the radiopurity of the crystals it is necessary to reduce potential sources for radioactive backgrounds such as U and Th. In this poster we will present our studies of the chemical purification of the CaCO{sub 3} and CaWO{sub 4} powders.

  3. The luminescence of CaWO4: Bi single crystals

    International Nuclear Information System (INIS)

    Zorenko, Yu.; Pashkovsky, M.; Voloshinovskii, A.; Kuklinski, B.; Grinberg, M.

    2006-01-01

    Influence of doping with Bi 3+ ions and Bi 3+ -Na + or Bi 3+ -Li + ions pairs on luminescence, emission kinetics and light yield of CaWO 4 crystals has been investigated. It has been shown that under excitation in the A-band at 272 and 287nm, related to the Bi 3+ ions absorption, the luminescence peaked at 468nm decaying with time τ=0.41μs is observed. For bismuth concentration 50-500ppm and the equimolar concentrations of the Bi 3+ ions accompanied by Na + or Li + ions compensators the significant suppression of the phosphorescence peaked at 520nm, related to the defect WO 3 -V O complex, and an improvement of scintillation characteristics of the CaWO 4 are noticed. Energy transfer from the defect WO 3 -V O and regular WO 4 2- oxy-anions to Bi 3+ ions have been observed at room temperatures and discussed

  4. Oxidative degradation of salicylic acid by sprayed WO{sub 3} photocatalyst

    Energy Technology Data Exchange (ETDEWEB)

    Mohite, S.V.; Rajpure, K.Y., E-mail: rajpure@yahoo.com

    2015-10-15

    Highlights: • The photoactivity of sprayed WO{sub 3} thin film. • Photoelectrocatalytic degradation of salicylic acid. • Reaction kinetics and mineralization of pollutants by COD. - Abstract: The WO{sub 3} thin films were deposited using spray pyrolysis technique. The prepared WO{sub 3} thin films were characterized using photoelectrochemical (PEC), X-ray diffraction, atomic force microscopy (AFM), and UV–vis absorbance spectroscopy techniques. PEC measurements of WO{sub 3} films deposited at different deposition temperatures were carried out to study photoresponse. The maximum photocurrent (I{sub ph} = 261 μA/cm{sup 2}) was observed for the film deposited at the 225 °C. The monoclinic crystal structure of WO{sub 3} has been confirmed from X-ray diffraction studies. AFM studies were used to calculate particle size and average roughness of the films. Optical absorbance was studied to estimate the bandgap energy of WO{sub 3} thin film which was about 2.65 eV. The photoelectrocatalytic activity of WO{sub 3} film was studied by degradation of salicylic acid with reducing concentrations as function of reaction time. The WO{sub 3} photocatalyst degraded salicylic acid to about 67.14% with significant reduction in chemical oxygen demand (COD) value.

  5. Intrinsic Defects and H Doping in WO3

    KAUST Repository

    Zhu, Jiajie; Vasilopoulou, Maria; Davazoglou, Dimitris; Kennou, Stella; Chroneos, Alexander; Schwingenschlö gl, Udo

    2017-01-01

    WO3 is widely used as industrial catalyst. Intrinsic and/or extrinsic defects can tune the electronic properties and extend applications to gas sensors and optoelectonics. However, H doping is a challenge to WO3, the relevant mechanisms being hardly

  6. Preparation of Ba1-xSrxWO4 and Ba1-xCaxWO4 films on tungsten plate by mechanically assisted solution reaction at room temperature

    International Nuclear Information System (INIS)

    Rangappa, Dinesh; Fujiwara, Takeshi; Watanabe, Tomoaki; Yoshimura, Masahiro

    2008-01-01

    Preparation of the alkaline earth tungstate films such as Ba 1-x Sr x WO 4 and Ba 1-x Ca x WO 4 on the tungsten substrate was studied with a simple solution process assisted with the ball rotation at room temperature. The solid solution formation and limitations, the effect of oxidizing agent H 2 O 2 and alkaline earth ions concentration on the dissolution of W substrate and the growth of Ba 1-x Sr x WO 4 and Ba 1-x Ca x WO 4 films were studied in detail. The ball rotation assistance plays a very important role to enhance the dissolution of the W substrate and mass transport of the reactant species such as alkaline earth ions and WO 4 2- ions onto the solid/solution interface region, where precipitation occurs. Therefore, the rate of film formation was accelerated by the ball rotation assistance to the reaction system. Ba-rich Ba 1-x Sr x WO 4 and Ba 1-x Ca x WO 4 films were formed without high energy or high temperature treatment

  7. Cr2O3 nanoparticle-functionalized WO3 nanorods for ethanol gas sensors

    Science.gov (United States)

    Choi, Seungbok; Bonyani, Maryam; Sun, Gun-Joo; Lee, Jae Kyung; Hyun, Soong Keun; Lee, Chongmu

    2018-02-01

    Pristine WO3 nanorods and Cr2O3-functionalized WO3 nanorods were synthesized by the thermal evaporation of WO3 powder in an oxidizing atmosphere, followed by spin-coating of the nanowires with Cr2O3 nanoparticles and thermal annealing in an oxidizing atmosphere. Scanning electron microscopy was used to examine the morphological features and X-ray diffraction was used to study the crystallinity and phase formation of the synthesized nanorods. Gas sensing tests were performed at different temperatures in the presence of test gases (ethanol, acetone, CO, benzene and toluene). The Cr2O3-functionalized WO3 nanorods sensor showed a stronger response to these gases relative to the pristine WO3 nanorod sensor. In particular, the response of the Cr2O3-functionalized WO3 nanorods sensor to 200 ppm ethanol gas was 5.58, which is approximately 4.4 times higher that of the pristine WO3 nanorods sensor. Furthermore, the Cr2O3-functionalized WO3 nanorods sensor had a shorter response and recovery time. The pristine WO3 nanorods had no selectivity toward ethanol gas, whereas the Cr2O3-functionalized WO3 nanorods sensor showed good selectivity toward ethanol. The gas sensing mechanism of the Cr2O3-functionalized WO3 nanorods sensor toward ethanol is discussed in detail.

  8. Poly(methacrylic acid)-mediated morphosynthesis of PbWO4 micro-crystals

    International Nuclear Information System (INIS)

    Yu, J.G.; Zhao, X.F.; Liu, S.W.; Li, M.; Mann, S.; Ng, D.H.L.

    2007-01-01

    PbWO 4 crystals with various morphologies were fabricated via a facile poly(methacrylic acid)-mediated hydrothermal route. Novel microsized PbWO 4 single crystals with a needle-like shape as well as other morphologies, such as a fishbone, dendrite, sphere, spindle, ellipsoid, rod, and dumbbell with two dandelion-like heads, could be produced. The presence of PMAA, [Pb 2+ ]/[WO 4 2- ] molar ratio (R), and aging temperature played key roles in the formation of the PbWO 4 needle-like structures. Between temperatures of 60 to 150 C, the length and photoluminescence intensities of the PbWO 4 micro needles significantly increased with aging temperature, while the diameter did not change remarkably. Time-dependent experiments revealed that the formation of PbWO 4 microneedles involved an unusual growth process, involving nucleation, oriented assembly and controlled mesoscale restructuring of nanoparticle building blocks. (orig.)

  9. Characterization of nanosized Al2(WO4)3

    International Nuclear Information System (INIS)

    Nihtianova, D.; Velichkova, N.; Nikolova, R.; Koseva, I.; Yordanova, A.; Nikolov, V.

    2011-01-01

    Graphical abstract: TEM method allows to detect small quantities of impurities not detectable by other methods. In our case impurities of W 5 O 14 are detected in Al 2 (WO 4 ) 3 nanopowder. Highlights: → Nanosized Al 2 (WO 4 ) 3 by simple co-precipitation method. → Spherical particles with mean size of 22 nm distributed between 10 and 40 nm at 630 o C. → XRD, DTA and TEM confirm well defined products with perfect structure. → TEM locality allows detection of impurities not detectable by XRD and DTA. -- Abstract: Nanosized aluminum tungstate Al 2 (WO 4 ) 3 was prepared by co-precipitation reaction between Na 2 WO 4 and Al(NO 3 ) 3 aqueous solutions. The powder size and shape, as well as size distribution are estimated after different conditions of powder preparation. The purity of the final product was investigated by XRD and DTA analyses, using the single crystal powder as reference. Between the specimen and the reference no difference was detected. The crystal structure of Al 2 (WO 4 ) 3 nanosized powder was confirmed by TEM (SAED, HRTEM). In additional, TEM locality allows to detect some W 5 O 14 impurities, which are not visible by conventional X-ray powder diffraction and thermal analyses.

  10. Structure of the short-range atomic order of WO3 amorphous films

    International Nuclear Information System (INIS)

    Olevskij, S.S.; Sergeev, M.S.; Tolstikhina, A.L.; Avilov, A.S.; Shkornyakov, S.M.; Semiletov, S.A.

    1984-01-01

    To study the causes of electrochromism manifestation in thin tungsten oxide films, the structure of WO 3 amorphous films has been investigated. The films were obtained by three different methods: by W(CO) 6 tungsten carbonyl pyrolysis, by high-frequency ion-plasma sputtering of a target prepared by WO 3 powder sintering, and by WO 3 powder thermal evaporation. Monocrystalline wafers of silicon and sodium chloride were used as substrates. The structure of short-range order in WO 3 amorphous films varies versus, the method of preparation in compliance with the type of polyhedral elements, (WO 6 , WO 5 ) and with the character of their packing (contacts via edges or vertices). Manifestation of electroc ro mism in WO 3 films prepared by varions methods and having different structure of short-range order is supposed to be realized through various mechanisms. One cannot exclude a potential simultaneous effect of the two coloration mechanisms

  11. MnWO{sub 4} nanocapsules: Synthesis, characterization and its electrochemical sensing property

    Energy Technology Data Exchange (ETDEWEB)

    Muthamizh, Selvamani; Suresh, Ranganathan; Giribabu, Krishnamoorthy; Manigandan, Ramadoss; Praveen Kumar, Sivakumar; Munusamy, Settu; Narayanan, Vengidusamy, E-mail: vnnara@yahoo.co.in

    2015-01-15

    Highlights: • Synthesis of MnWO{sub 4} nanocapsules without use of any other external reagent. • High crystalline MnWO{sub 4} was obtained with phase purity. • Electrochemical sensing platform based on MnWO{sub 4} for sensing quercetin. • Micromolar detection ability of MnWO{sub 4} modified GCE. - Abstract: Manganese tungstate (MnWO{sub 4}) was synthesized by surfactant free precipitation method. MnWO{sub 4} was characterized by using various spectroscopic techniques. The phase, crystalline nature and the morphological analysis were carried out using XRD, scanning electron microscopy (SEM), and high resolution transmission electron microscopy (HR-TEM). Further, FT-IR, Raman, and DRS-UV–Vis spectral analysis were carried out in order to ascertain the optical property and the presence of functional groups. From the analysis, the morphology of the MnWO{sub 4} was observed to be in capsules with breadth and thickness were in nm range. The oxidation state of tungsten (W), and manganese (Mn) were investigated using X-ray photo electron spectroscopy (XPS) and electron paramagnetic resonance spectroscopy (EPR). The synthesized MnWO{sub 4} nanocapsules were used to modify glassy carbon electrode (GCE) to detect quercetin.

  12. Visible-light photocatalytic activity of graphene oxide-wrapped Bi2WO6 hierarchical microspheres

    Science.gov (United States)

    Zhai, Jiali; Yu, Hongwen; Li, Haiyan; Sun, Lei; Zhang, Kexin; Yang, Hongjun

    2015-07-01

    A facile approach of fabricating homogeneous graphene oxide (GO)-wrapped Bi2WO6 microspheres (GO/Bi2WO6) is developed. The transmission electron microscopy (TEM) results show that a heterojunction interface between GO and Bi2WO6. The UV-vis diffuse reflection spectra (DRS) reveal that the as-prepared GO/Bi2WO6 composites own more intensive absorption in the visible light range compared with pure Bi2WO6. These characteristic structural and optical properties endow GO/Bi2WO6 composites with enhanced photocatalytic activity. The enhanced photocatalytic activity of the GO/Bi2WO6 is attributed predominantly to the synergetic effect between GO and Bi2WO6, causing rapid generation and separation of photo-generated charge carriers.

  13. WO3 Nanowires on Graphene Sheets as Negative Electrode for Supercapacitors

    Directory of Open Access Journals (Sweden)

    Bo Liu

    2017-01-01

    Full Text Available WO3 nanowires directly grown on graphene sheets have been fabricated by using a seed-mediated hydrothermal method. The morphologies and electrochemical performance of WO3 films prepared by different process were studied. The results show that the precoated nanoseeds and graphene sheets on graphite electrode provide more reactive centers for the nucleation and formation of uniform WO3 nanowires. The WO3 nanowires electrode exhibits a high area specific capacitance of 800 mF cm−2 over negative potential range from −1.0 V to 0 V versus SCE in 1 M Li2SO4 solution. A high performance electrochemical supercapacitor assembled with WO3 nanowires as negative electrode and PANI/MnO2 as positive electrodes over voltage range of 1.6 V displays a high volumetric capacitance of 2.5 F cm−3, which indicate great potential applications of WO3 nanowires on graphene sheets as negative electrode for energy storage devices.

  14. CTAB-assisted ultrasonic synthesis, characterization and photocatalytic properties of WO{sub 3}

    Energy Technology Data Exchange (ETDEWEB)

    Sánchez-Martínez, D., E-mail: dansanm@gmail.com; Gomez-Solis, C.; Torres-Martinez, Leticia M.

    2015-01-15

    Highlights: • WO{sub 3} 2D nanostructures were synthesized by ultrasound method assisted with CTAB. • WO{sub 3} morphology was mainly of rectangular nanoplates with a thickness of ∼50 nm. • The highest surface area value of WO{sub 3} was obtained to lowest concentration of CTAB. • WO{sub 3} activity was attributed to morphology, surface area and the addition of CTAB. • WO{sub 3} nanoplates were able to causing almost complete mineralization of rhB and IC. - Abstract: WO{sub 3} 2D nanostructures have been prepared by ultrasound synthesis method assisted with CTAB using different molar ratios. The formation of monoclinic crystal structure of WO{sub 3} was confirmed by X-ray powder diffraction (XRD). The characterization of the WO{sub 3} samples was complemented by analysis of scanning electron microscopy (SEM), which revealed morphology mainly of rectangular nanoplates with a thickness of around 50 nm and length of 100–500 nm. Infrared spectroscopy (FT-IR) was used to confirm the elimination of the CTAB in the synthesized samples. The specific surface area was determinate by the BET method and by means of diffuse reflectance spectroscopy (DRS) it was determinate the band-gap energy (E{sub g}) of the WO{sub 3} samples. The photocatalytic activity of the WO{sub 3} oxide was evaluated in the degradation reactions of rhodamine B (rhB) and indigo carmine (IC) under Xenon lamp irradiation. The highest photocatalytic activity was observed in the samples containing low concentration of CTAB with morphology of rectangular nanoplates and with higher surface area value than commercial WO{sub 3}. Photodegradation of rhB and IC were followed by means of UV–vis absorption spectra. The mineralization degree of organic dyes by WO{sub 3} photocatalyst was determined by total organic carbon analysis (TOC) reaching percentages of mineralization of 92% for rhB and 50% for IC after 96 h of lamp irradiation.

  15. Photocatalytic activity of Bi{sub 2}WO{sub 6}/Bi{sub 2}S{sub 3} heterojunctions: the facilitation of exposed facets of Bi{sub 2}WO{sub 6} substrate

    Energy Technology Data Exchange (ETDEWEB)

    Yan, Long [School of Chemistry and Chemical Engineering, Yulin University, Shaanxi Key Laboratory of Low Metamorphic Coal Clean Utilization, Yulin 71900 (China); School of Chemistry and Chemical Engineering, Yan’an University, Shaanxi Key Laboratory of Chemical Reaction Engineering, Yan’an 716000 (China); Wang, Yufei [School of Chemistry and Chemical Engineering, Yulin University, Shaanxi Key Laboratory of Low Metamorphic Coal Clean Utilization, Yulin 71900 (China); Shen, Huidong; Zhang, Yu [School of Chemistry and Chemical Engineering, Yan’an University, Shaanxi Key Laboratory of Chemical Reaction Engineering, Yan’an 716000 (China); Li, Jian [School of Chemistry and Chemical Engineering, Yulin University, Shaanxi Key Laboratory of Low Metamorphic Coal Clean Utilization, Yulin 71900 (China); Wang, Danjun, E-mail: yulyanlong@aliyun.com [School of Chemistry and Chemical Engineering, Yan’an University, Shaanxi Key Laboratory of Chemical Reaction Engineering, Yan’an 716000 (China)

    2017-01-30

    Highlights: • Bi{sub 2}S{sub 3}/Bi{sub 2}WO{sub 6} hybrids with exposed (020) Bi{sub 2}WO{sub 6} facets have been synthesized. • X-ray photoelectron spectroscopy reveals that a small amount of Bi{sub 2}S{sub 3} was formed. • The enhanced photoactivity of hybrids is due to heterojunction and (020) facets. • A possible photocatalytic degradation mechanism is proposed. - Abstract: Bi{sub 2}S{sub 3}/Bi{sub 2}WO{sub 6} hybrid architectures with exposed (020) Bi{sub 2}WO{sub 6} facets have been synthesized via a controlled anion exchange approach. X-ray photoelectron spectroscopy (XPS) reveals that a small amount of Bi{sub 2}S{sub 3} was formed on the surface of Bi{sub 2}WO{sub 6} during the anion exchange process, thus leading to the transformation from the Bi{sub 2}WO{sub 6} to Bi{sub 2}S{sub 3}/Bi{sub 2}WO{sub 6}. A rhodamine B (RhB) aqueous solution was chosen as model organic pollutants to evaluate the photocatalytic activities of the Bi{sub 2}S{sub 3}/Bi{sub 2}WO{sub 6} catalysts. Under visible light irradiation, the Bi{sub 2}S{sub 3}/Bi{sub 2}WO{sub 6}-TAA displayed the excellent visible light photoactivities compared with pure Bi{sub 2}S{sub 3}, Bi{sub 2}WO{sub 6} and other composite photocatalysts. The efficient photocatalytic activity of the Bi{sub 2}S{sub 3}/Bi{sub 2}WO{sub 6}-TAA composite microspheres was ascribed to the constructed heterojunctions and the inner electric field caused by the exposed (020) Bi{sub 2}WO{sub 6} facets. Active species trapping experiments revealed that h{sup +} and O{sub 2}·{sup −} are the main active species in the photocatalytic process. Furthermore, the as-obtained photocatalysts showed good photocatalytic activity after four recycles. The results presented in this study provide a new concept for the rational design and development of highly efficient photocatalysts.

  16. Structural, vibrational and luminescence properties of the (1−x)CaWO{sub 4}−xCdWO{sub 4} system

    Energy Technology Data Exchange (ETDEWEB)

    Taoufyq, A. [Institut Matériaux Microélectronique et Nanosciences de Provence, Aix Marseille Université, CNRS, Université de Toulon, IM2NP UMR 7334, 83957, La Garde (France); Laboratoire Matériaux et Environnement LME, Faculté des Sciences, Université Ibn Zohr, BP 8106, Cité Dakhla, Agadir, Maroc (Morocco); CEA/DEN, Département d’Études des Réacteurs, Laboratoire Dosimétrie Capteurs Instrumentation, CEA Cadarache, 13108, Saint-Paul-lez-Durance (France); Société CESIGMA, Signals and Systems, 1576 Chemin de La Planquette, 83130 La Garde (France); Guinneton, F.; Valmalette, J-C.; Arab, M. [Institut Matériaux Microélectronique et Nanosciences de Provence, Aix Marseille Université, CNRS, Université de Toulon, IM2NP UMR 7334, 83957, La Garde (France); Benlhachemi, A.; Bakiz, B. [Laboratoire Matériaux et Environnement LME, Faculté des Sciences, Université Ibn Zohr, BP 8106, Cité Dakhla, Agadir, Maroc (Morocco); Villain, S. [Institut Matériaux Microélectronique et Nanosciences de Provence, Aix Marseille Université, CNRS, Université de Toulon, IM2NP UMR 7334, 83957, La Garde (France); and others

    2014-11-15

    In the present work, we investigate the structural, microstructural, vibrational and luminescence properties of the system (1−x)CaWO{sub 4}−xCdWO{sub 4} with x ranging between 0 and 1. Polycrystalline samples were elaborated using a coprecipitation technique followed by thermal treatment at 1000 °C. The samples were then characterized using X-ray diffraction, scanning electron microscopy, Raman spectroscopy and luminescence analyses. X-ray diffraction profile analyses using Rietveld method showed that two kinds of solid solutions Ca{sub 1−x}Cd{sub x}WO{sub 4} having scheelite and wolframite structures, with respectively tetragonal and monoclinic crystal cells, were observed, with a biphasic system for compositions x=0.6 and 0.7. The scanning electron microscopy experiments showed a complex evolution of morphologies and crystallite sizes as x increased. The vibration modes of Raman spectra were characteristic of composition-dependent disordered solid solutions with decreasing wavenumbers as x increased. Luminescence experiments were performed under UV-laser light irradiation. The energies of emission bands increased linearly with cadmium composition x. The integrated intensity of luminescence reached a maximum value for the substituted wolframite phase with composition x=0.8. - Graphical abstract: Luminescence on UV excitation (364.5 nm) of (1−x)CaWO{sub 4−x}CdWO{sub 4} system, elaborated from coprecipitation technique at 1000 °C, with 0WO{sub 4} polycrystalline phases with 0≤x≤0.5. (b) Maximum of luminescence intensity for the composition x=0.8. - Highlights: • Solid solutions Ca{sub 1−x}Cd{sub x}WO{sub 4} are elaborated from coprecipitation technique. • The structures of two types of solid solutions are refined using Rietveld method. • A maximum of luminescence is obtained for an intermediate composition x=0.8.

  17. Facile synthesis of hierarchical double-shell WO{sub 3} microspheres with enhanced photocatalytic activity

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Zhenfeng [College of Environment and Chemical Engineering, Tianjin Polytechnic University, Tianjin 300387 (China); State Key Laboratory of Hollow-Fiber Membrane Materials and Membrane Processes, Tianjin 300387 (China); Chu, Deqing, E-mail: dqingchu@163.com [College of Environment and Chemical Engineering, Tianjin Polytechnic University, Tianjin 300387 (China); State Key Laboratory of Hollow-Fiber Membrane Materials and Membrane Processes, Tianjin 300387 (China); Wang, Limin, E-mail: wanglimin@tjpu.edu.cn [School of Materials Science and Engineering, Tianjin Polytechnic University, Tianjin 300387 (China); State Key Laboratory of Hollow-Fiber Membrane Materials and Membrane Processes, Tianjin 300387 (China); Wang, Lipeng [School of Materials Science and Engineering, Tianjin Polytechnic University, Tianjin 300387 (China); Hu, Wenhui; Chen, Xiangyu; Yang, Huifang [College of Environment and Chemical Engineering, Tianjin Polytechnic University, Tianjin 300387 (China); Sun, Jingjing [School of Materials Science and Engineering, Tianjin Polytechnic University, Tianjin 300387 (China)

    2017-02-28

    Highlights: • HDS-WO{sub 3} were fabricated via mild process. • A possible growth mechanism for HDS-WO{sub 3} is proposed. • The excellent photocatalytic activity is attributed to the larger surface area of the HDS-WO{sub 3} nanostructures. - Abstract: Hierarchical double-shell WO{sub 3} microspheres (HDS-WO{sub 3}) have been successfully obtained through the thermal decomposition of WO{sub 3}·H{sub 2}O formed by metal salts as the templates. The products were characterized by X-ray diffraction (XRD), and the morphology was investigated by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). In addition, the HDS-WO{sub 3} microspheres were analyzed by the Thermogravimetric (TG) and Brunauer-Emmett-Teller (BET) analysis. The synthetic mechanism of the products with hierarchical structures was proposed. The obtained HDS-WO{sub 3} exhibits excellent photocatalytic efficiency (84.9%), which is much higher than other WO{sub 3} sample under visible light illumination.

  18. Biomimetic fabrication of WO3 for water splitting under visible light with high performance

    International Nuclear Information System (INIS)

    Yin, Chao; Zhu, Shenmin; Yao, Fan; Gu, Jiajun; Zhang, Wang; Chen, Zhixin; Zhang, Di

    2013-01-01

    Inspired by the high light-harvesting properties of typical butterfly wings, ceramic WO 3 butterfly wings with hierarchical structures of bio-butterfly wings was fabricated using a template of PapilioParis butterfly wings through a sol–gel method. The effect of calcination temperatures on the structures of the ceramic butterfly wings was investigated and the results showed that the WO 3 butterfly wing replica calcined at 550 °C (WO 3 replica-550) is a single phase and has a high crystallinity and relatively fine hierarchical structure. The average grain size of WO 3 replica-550 and WO 3 powder are around 32.6 and 42.2 nm, respectively. Compared with pure WO 3 powder, WO 3 replica-550 demonstrated a higher light-harvesting capability in the region from 460 to 700 nm and more importantly the higher charge separation rate, as evidenced by electron paramagnetic resonance measurements. Photocatalytic O 2 evolutions from water were investigated on the ceramic butterfly wings and pure WO 3 powder under visible light (λ > 420 nm). The results showed that the amount of O 2 produced from WO 3 replica-550 is 50 % higher than that of the pure WO 3 powder. The improved photocatalytic performance of WO 3 replica-550 is attributed to the quasi-honeycomb structure inherited from the PapilioParis butterfly wings, providing both high light-harvesting efficiency and efficient charge transport through the WO 3

  19. Preparation and characterization of nanocrystalline porous TiO2/WO3 composite thin films

    International Nuclear Information System (INIS)

    Hsu, C.-S.; Lin, C.-K.; Chan, C.-C.; Chang, C.-C.; Tsay, C.-Y.

    2006-01-01

    TiO 2 materials possessing not only photocatalytic but also electrochromic properties have attracted many research and development interests. Though WO 3 exhibits excellent electrochromic properties, the much higher cost and water-sensitivity of WO 3 as compared with the TiO 2 may restrict the practical application of WO 3 materials. In the present study, the feasibility of preparing nanocrystalline porous TiO 2 /WO 3 composite thin films was investigated. Precursors of sols TiO 2 and/or WO 3 and polystyrene microspheres were used to prepare nanocrystalline pure TiO 2 , WO 3 , and composite TiO 2 /WO 3 thin films by spin coating. The spin-coated thin films were amorphous and, after heat treating at a temperature of 500 o C, nanocrystalline TiO 2 , TiO 2 /WO 3 , and WO 3 thin films with or without pores were prepared successfully. The heat-treated thin films were colorless and coloration-bleaching phenomena can be observed during cyclic voltammetry tests. The heat-treated thin films exhibited good reversible electrochromic behavior while the porous TiO 2 /WO 3 composite film exhibited improved electrochromic properties

  20. Electrochromic device based on electrospun WO{sub 3} nanofibers

    Energy Technology Data Exchange (ETDEWEB)

    Dulgerbaki, Cigdem; Maslakci, Neslihan Nohut; Komur, Ali Ihsan; Oksuz, Aysegul Uygun, E-mail: ayseguluygun@sdu.edu.tr

    2015-12-15

    Highlights: • WO{sub 3} electrochromic nanofibers were prepared by electrospinning technique. • WO{sub 3} nanofibers switched reversibly from transparent to blue color. • Electrochromic device was assembled using ionic liquid based gel electrolyte. • Significant optical modulation and excellent cycling stability were achieved for ECD. - Abstract: The tungsten oxide (WO{sub 3}) nanofibers were grown directly onto an ITO-coated glass via an electrospinning method for electrochromic applications. The electrochromic properties of WO{sub 3} nanofibers were investigated in the presence of different electrolytes including a series of ionic liquids and classic LiClO{sub 4}-PC system. A significant optical modulation of 20.82% at 760 nm, reversible coloration with efficiency of 64.58 cm{sup 2}/C and excellent cycling stability were achieved for the nanofiber electrochromic device (ECD) with ionic liquid based gel electrolyte.

  1. Investigation of radiation shielding properties for MeO-PbCl2-TeO2 (MeO = Bi2O3, MoO3, Sb2O3, WO3, ZnO) glasses

    Science.gov (United States)

    Sayyed, M. I.; Çelikbilek Ersundu, M.; Ersundu, A. E.; Lakshminarayana, G.; Kostka, P.

    2018-03-01

    In this work, glasses in the MeO-PbCl2-TeO2 (MeO = Bi2O3, MoO3, Sb2O3, WO3, ZnO) system, which show a great potential for optoelectronic applications, were used to evaluate their resistance under high energy ionizing radiations. The basic shielding quantities for determining the penetration of radiation in glass, such as mass attenuation coefficient (μ/ρ), half value layer (HVL), mean free path (MFP) and exposure buildup factor (EBF) values were investigated within the energy range 0.015 MeV ‒ 15 MeV using XCOM program and variation of shielding parameters were compared with different glass systems and ordinary concrete. From the derived results, it was determined that MeO-PbCl2-TeO2 (MeO = Bi2O3, MoO3, Sb2O3, WO3, ZnO) glasses show great potentiality to be used under high energy radiations. Among the studied glass compositions, Bi2O3 and WO3 containing glasses were found to possess superior gamma-ray shielding effectiveness.

  2. Optical properties of WO3 thin films using surface plasmon resonance technique

    International Nuclear Information System (INIS)

    Paliwal, Ayushi; Sharma, Anjali; Gupta, Vinay; Tomar, Monika

    2014-01-01

    Indigenously assembled surface plasmon resonance (SPR) technique has been exploited to study the thickness dependent dielectric properties of WO 3 thin films. WO 3 thin films (80 nm to 200 nm) have been deposited onto gold (Au) coated glass prism by sputtering technique. The structural, optical properties and surface morphology of the deposited WO 3 thin films were studied using X-ray diffraction, UV-visible spectrophotometer, Raman spectroscopy, and Scanning electron microscopy (SEM). XRD analysis shows that all the deposited WO 3 thin films are exhibiting preferred (020) orientation and Raman data indicates that the films possess single phase monoclinic structure. SEM images reveal the variation in grain size with increase in thickness. The SPR reflectance curves of the WO 3 /Au/prism structure were utilized to estimate the dielectric properties of WO 3 thin films at optical frequency (λ = 633 nm). As the thickness of WO 3 thin film increases from 80 nm to 200 nm, the dielectric constant is seen to be decreasing from 5.76 to 3.42, while the dielectric loss reduces from 0.098 to 0.01. The estimated value of refractive index of WO 3 film is in agreement to that obtained from UV-visible spectroscopy studies. The strong dispersion in refractive index is observed with wavelength of incident laser light

  3. Synthesis of WO3 flower-like hierarchical architectures and their sensing properties

    International Nuclear Information System (INIS)

    Meng, Dan; Wang, Guosheng; San, Xiaoguang; Song, Yinmin; Shen, Yanbai; Zhang, Yajing; Wang, Kangjun; Meng, Fanli

    2015-01-01

    WO 3 flower-like hierarchical architectures were synthesized by hydrothermal process using sodium tungstate (Na 2 WO 4 ·2H 2 O) as tungsten source and citric acid (CA) as an assistant agent. The morphology and crystal structure were investigated using scanning electron microscope and X-ray diffractometer. It is found that CA played a significant role in governing morphologies of product during hydrothermal process. The obtained products were identified as triclinic crystal WO 3 structure. The ethanol gas sensing measurements showed that well-defined WO 3 flower-like structures synthesized at CA/W molar ratio of 1 with large specific surface area exhibited the higher responses compared with others at all operating temperatures. Moreover, the reversible and fast response to ethanol gas at various gas concentrations and good selectivity were obtained. The results indicated that the WO 3 flower-like hierarchical architectures are promising materials for gas sensors. - Highlights: • WO 3 flower-like structures were successfully synthesized by hydrothermal method. • The effect of citric acid amount on morphologies was investigated. • Good ethanol gas sensing properties of WO 3 flower-like structures were obtained

  4. Photoelectrochemical Properties and Behavior of α-SnWO4 Photoanodes Synthesized by Hydrothermal Conversion of WO3 Films.

    Science.gov (United States)

    Zhu, Zhehao; Sarker, Pranab; Zhao, Chenqi; Zhou, Lite; Grimm, Ronald L; Huda, Muhammad N; Rao, Pratap M

    2017-01-18

    Metal oxides with moderate band gaps are desired for efficient production of hydrogen from sunlight and water via photoelectrochemical (PEC) water splitting. Here, we report an α-SnWO 4 photoanode synthesized by hydrothermal conversion of WO 3 films that achieves photon to current conversion at wavelengths up to 700 nm (1.78 eV). This photoanode is promising for overall PEC water-splitting because the flat-band potential and voltage of photocurrent onset are more negative than the potential of hydrogen evolution. Furthermore, the photoanode utilizes a large portion of the solar spectrum. However, the photocurrent density reaches only a small fraction of that which is theoretically possible. Density functional theory based thermodynamic and electronic structure calculations were performed to elucidate the nature and impact of defects in α-SnWO 4 prepared by this synthetic route, from which hole localization at Sn-at-W antisite defects was determined to be a likely cause for the poor photocurrent. Measurements further showed that the photocurrent decreases over time due to surface oxidation, which was suppressed by improving the kinetics of hole transfer at the semiconductor/electrolyte interface. Alternative synthetic methods and the addition of protective coatings and/or oxygen evolution catalysts are suggested to improve the PEC performance and stability of this promising α-SnWO 4 material.

  5. Synthesis and characterization of polyaniline/MnWO4 nanocomposites as electrodes for pseudocapacitors

    Science.gov (United States)

    Saranya, S.; Selvan, R. Kalai; Priyadharsini, N.

    2012-03-01

    Polyaniline (PAni)/MnWO4 nanocomposite was successfully synthesized by in situ polymerization method under ultrasonication and the MnWO4 was prepared by surfactant assisted ultrasonication method. The thermal stability of PAni was determined by TG/DTA (Thermo Gravimetric/ Differential thermal analysis). The structural and morphological features of PAni, MnWO4 and PAni/MnWO4 composite was analyzed using Fourier transform infrared spectrometry, X-ray diffraction (XRD), scanning electron microscope (SEM) and Transmission electron microscope (TEM) images. The electro-chemical properties of PAni, MnWO4 and its composites with different weight percentage of MnWO4 loading were studied through cyclic voltammetry (CV) for the application of supercapacitors as active electrode materials. From the cyclic voltammogram, 50% of MnWO4 impregnated PAni showed a high specific capacitance (SC) of 481 F/g than their individual counterparts of PAni (396 F/g) and MnWO4 (18 F/g). The galvanostatic charge-discharge studies indicate the in situ polymerized composite shows greater specific capacitance (475 F/g) than the physical mixture (346 F/g) at a constant discharge current of 1 mA/cm2 with reasonable cycling stability. The charge transfer resistance (Rct) of PAni/MnWO4 composite (22 ohm) was calculated using electrochemical impedance spectroscopy (EIS) and compared with its physical mixture (58 ohm).

  6. Gamma ray shielding and structural properties of PbO-P2O5-Na2WO4 glass system

    Science.gov (United States)

    Dogra, Mridula; Singh, K. J.; Kaur, Kulwinder; Anand, Vikas; Kaur, Parminder

    2017-05-01

    The present work has been undertaken to study the gamma ray shielding properties of PbO-P2O5-Na2WO4 glass system. The values of mass attenuation coefficient and half value layer parameter at photon energies 511, 662 and 1173 KeV have been determined using XCOM computer software developed by National Institute of Standards and Technology. The density, molar volume, XRD, UV-VIS and Raman studies have been performed to study the structural properties of the prepared glass system to check the possibility of the use of prepared samples as an alternate to conventional concrete for gamma ray shielding applications.

  7. Characterization of MAPLE deposited WO3 thin films for electrochromic applications

    Science.gov (United States)

    Boyadjiev, S. I.; Stefan, N.; Szilágyi, I. M.; Mihailescu, N.; Visan, A.; Mihailescu, I. N.; Stan, G. E.; Besleaga, C.; Iliev, M. T.; Gesheva, K. A.

    2017-01-01

    Tungsten trioxide (WO3) is a widely studied material for electrochromic applications. The structure, morphology and optical properties of WO3 thin films, grown by matrix assisted pulsed laser evaporation (MAPLE) from monoclinic WO3 nano-sized particles, were investigated for their possible application as electrochromic layers. A KrF* excimer (λ=248 nm, ζFWHM=25 ns) laser source was used in all experiments. The MAPLE deposited WO3 thin films were studied by atomic force microscopy (AFM), grazing incidence X-ray diffraction (GIXRD) and Fourier transform infrared spectroscopy (FTIR). Cyclic voltammetry measurements were also performed, and the coloring and bleaching were observed. The morpho-structural investigations disclosed the synthesis of single-phase monoclinic WO3 films consisting of crystalline nano-grains embedded in an amorphous matrix. All thin films showed good electrochromic properties, thus validating application of the MAPLE deposition technique for the further development of electrochromic devices.

  8. Characterization of MAPLE deposited WO3 thin films for electrochromic applications

    International Nuclear Information System (INIS)

    Boyadjiev, S I; Iliev, M T; Stefan, N; Mihailescu, N; Visan, A; Mihailescu, I N; Szilágyi, I M; Stan, G E; Besleaga, C; Gesheva, K A

    2017-01-01

    Tungsten trioxide (WO 3 ) is a widely studied material for electrochromic applications. The structure, morphology and optical properties of WO 3 thin films, grown by matrix assisted pulsed laser evaporation (MAPLE) from monoclinic WO 3 nano-sized particles, were investigated for their possible application as electrochromic layers. A KrF* excimer (λ=248 nm, ζ FWHM =25 ns) laser source was used in all experiments. The MAPLE deposited WO 3 thin films were studied by atomic force microscopy (AFM), grazing incidence X-ray diffraction (GIXRD) and Fourier transform infrared spectroscopy (FTIR). Cyclic voltammetry measurements were also performed, and the coloring and bleaching were observed. The morpho-structural investigations disclosed the synthesis of single-phase monoclinic WO 3 films consisting of crystalline nano-grains embedded in an amorphous matrix. All thin films showed good electrochromic properties, thus validating application of the MAPLE deposition technique for the further development of electrochromic devices. (paper)

  9. Influence of disordered morphology on electrochromic stability of WO{sub 3}/PPy

    Energy Technology Data Exchange (ETDEWEB)

    Gaikwad, Digambar K. [D. Y. Patil College of Engineering & Technology, Kasaba Bawada, Kolhapur, 416006, Maharashtra (India); Mali, Sawanta S.; Hong, Chang K. [Polymer Energy Materials Laboratory, Department of Advanced Chemical Engineering, Chonnam National University, Gwangju, 500-757 (Korea, Republic of); Kadam, Anamika V., E-mail: anamikasonavane@rediff.com [D. Y. Patil College of Engineering & Technology, Kasaba Bawada, Kolhapur, 416006, Maharashtra (India); D.Y. Patil Medical University, Kasaba Bawada, Kolhapur, 416006, Maharashtra (India)

    2016-06-05

    Tungsten oxide (WO{sub 3}) films are critical for smart windows because of their capacity of varying the throughput of visible light and solar energy. This study highlights the evolution of structural and morphological changes of electrodeposited WO{sub 3} thin films coated with polypyrrole (PPy) by using chemical bath deposition. The structural and surface properties of WO{sub 3} thin films were studied using X-ray diffraction, Fourier transform infrared spectroscopy, scanning electron microscopy, and transmission electron microscopy. The electrochemical stability was inspected using repetitive cyclic voltammetry (CV) cycles for each sample in LiClO{sub 4}-PC electrolyte for prolonged periods. The results showed an improvement in the electrochemical stability after the CV study. - Graphical abstract: Mechanism: A schematic of the mechanism is proposed in above fig. The mechanism is based on three step process: (i) WO{sub 3} coated on ITO by electrodeposition followed by thermal treatment. It produces ordered nanoarrayed morphology. (ii) A second step involving deposition of PPy by chemical bath deposition on ITO. It possesses globular morphology. (iii) When PPy coated on WO{sub 3}, PPy applies shearing force on WO{sub 3} and produces disordered nanoarrayed morphology. - Highlights: • Nanoarrayed WO{sub 3}/PPy composite was synthesized. • Interplanar spacing enhances due to PPy coating. • PPy applies shearing force on WO{sub 3} produces disordered morphology. • Nanocomposite showed high stability in LiClO{sub 4}-PC.

  10. Effect of Structural Stress on the Laser Quality of Highly Doped Yb:KY(WO4)2/KY(WO4)2 and Yb:KLu(WO4)2/KLu(WO4)2 Epitaxial Structures

    International Nuclear Information System (INIS)

    Carvajal, J.; Raghothamachar, B.; Silvestre, O.; Chen, H.; Pujol, M.; Petrov, V.; Dudley, M.; Aguilo, M.; Diaz, F.

    2009-01-01

    In this communication we demonstrate how the difference in laser performance of two highly doped (20 at %) epitaxial layers of Yb-doped KY(WO4)2 (KYW) grown on a KYW substrate and Yb-doped KLu(WO4)2 (KLuW) grown on a KLuW substrate, respectively, is related to the presence of structural stress in the epilayers, investigated by synchrotron white beam X-ray topography. From the results obtained, it is clear that the samples that show a larger amount of structural stress, Yb:KYW/KYW epitaxies, lead to lower efficiency in laser operation, giving a direct correlation between the existence and magnitude of such structural stress and the loss in efficiency of laser performance in such epitaxial layers which, from a spectroscopical point of view, are otherwise equivalent.

  11. Enhanced electrochromic coloration in Ag nanoparticle decorated WO3 thin films

    International Nuclear Information System (INIS)

    Kharade, Rohini R.; Mali, Sawanta S.; Patil, Satish P.; Patil, Kashinath R.; Gang, Myong G.; Patil, Pramod S.; Kim, Jin H.; Bhosale, Popatrao N.

    2013-01-01

    Highlights: • Electrochromic WO 3 /Ag nanocomposites prepared by hybrid physico-chemical route. • XRD and XPS results confirm formation of Ag 8 W 4 O 16 phase. • WO 3 /Ag thin films showed good optical transmittance change and coloration efficiency. • SPR enhanced coloration and bleaching mechanism is well explained for electrochromism. • Color stimuli are quantified using CIE chromaticity principles. -- Abstract: WO 3 /Ag composite thin films were prepared by microwave assisted sol–gel synthesis (MW-SGS) of WO 3 followed by vacuum evaporation of Ag nanoparticles and their enhanced electrochromic coloration was investigated. The composition and morphology of WO 3 thin films with different thickness of Ag layer obtained by vacuum evaporation were investigated. Distinct plasmon absorption bands of Ag nanoparticle thin films were obtained. The optical band gap energy of WO 3 /Ag films decreased with increasing the Ag layer thickness. The surface of these films has been examined using X-ray photoelectron spectroscopy (XPS) to gain information about the chemical states of species present at surfaces. Experimental results indicated that the conductivity of the films increased after surface modification by Ag layer. To investigate the origin of enhanced electrochromic absorption in optical properties, working electrode consisting of WO 3 /Ag thin film was used and observed the optical properties during electrochemical reaction. It was found that composite electrode shows enhancement in electrochromic properties in terms of optical modulation (ΔOD) and coloration efficiency (η)

  12. Prestressed concrete. Composite material perfectly utilizing the merits of steel and concrete; Puresutoresu concrete. Ko to concreteto no tokucho wo kanzen ni ikashita fukugo sozai

    Energy Technology Data Exchange (ETDEWEB)

    Sugawara, M. [Kyokuto Kogen Concrete Shinko Co. Ltd., Tokyo (Japan)

    1996-10-15

    Since the early stage of the development of the prestressed concrete (PC) manufacturing techniques, it has been said that forming a single PC structure by uniting precast segments with PC steel material into one is a construction method making the most of the feature of PC. This paper roughly describes the history of the development of PC and concrete examples of PC, centering on the construction techniques effectively utilizing the principle of PC and its materials. Especially, a PC bridge is superior to a steel bridge with respect to noise and vibration, so that the construction works of replacing railway steel bridges and railway elevated bridges by PC bridges have come to be seen in many places recently. In order to increase the span of a PC bridge, the reduction of the weight is a major factor. Therefore, an outer cable system has come to be used so as to reduce the thickness is cross section of the web of a PC beam as much as possible. The changes of the maximum span of cable stayed bridge are listed in a table in comparison of PC bridges with steel bridges. 29 refs., 9 figs., 1 tab.

  13. Low-temperature molten salt synthesis and characterization of CoWO4 nano-particles

    International Nuclear Information System (INIS)

    Song Zuwei; Ma Junfeng; Sun Huyuan; Sun Yong; Fang Jingrui; Liu Zhengsen; Gao Chang; Liu Ye; Zhao Jingang

    2009-01-01

    CoWO 4 nano-particles were successfully synthesized at a low temperature of 270 deg. C by a molten salt method, and effects of such processing parameters as holding time and salt quantity on the crystallization and development of CoWO 4 crystallites were initially studied. The products were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), and photoluminescent spectra techniques (PL), respectively. Experimental results showed that the well-crystallized CoWO 4 nano-particles with ca. 45 nm in diameter could be obtained at 270 deg. C for a holding time of 8 h with 6:1 mass ratio of the salt to CoWO 4 precursor, and XRD analysis evidenced that the as-prepared sample was a pure monoclinic phase of CoWO 4 with wolframite structure. Their PL spectra revealed that the CoWO 4 nano-particles displayed a very strong PL peak at 453 nm with the excitation wavelength of 230 nm, and PL properties of CoWO 4 crystallites relied on their crystalline state, especially on their particle size.

  14. Tungsten oxide (WO3) thin films for application in advanced energy systems

    International Nuclear Information System (INIS)

    Gullapalli, S. K.; Vemuri, R. S.; Manciu, F. S.; Enriquez, J. L.; Ramana, C. V.

    2010-01-01

    Inherent processes in coal gasification plants produce hazardous hydrogen sulfide (H 2 S), which must be continuously and efficiently detected and removed before the fuel is used for power generation. An attempt has been made in this work to fabricate tungsten oxide (WO 3 ) thin films by radio-frequency reactive magnetron-sputter deposition. The impetus being the use of WO 3 films for H 2 S sensors in coal gasification plants. The effect of growth temperature, which is varied in the range of 30-500 deg. C, on the growth and microstructure of WO 3 thin films is investigated. Characterizations made using scanning electron microscopy (SEM) and x-ray diffraction (XRD) indicate that the effect of temperature is significant on the microstructure of WO 3 films. XRD and SEM results indicate that the WO 3 films grown at room temperature are amorphous, whereas films grown at higher temperatures are nanocrystalline. The average grain-size increases with increasing temperature. WO 3 films exhibit smooth morphology at growth temperatures ≤300 deg. C while relatively rough at >300 deg. C. The analyses indicate that the nanocrystalline WO 3 films grown at 100-300 deg. C could be the potential candidates for H 2 S sensor development for application in coal gasification systems.

  15. A study on properties of PbWO4 crystal

    International Nuclear Information System (INIS)

    He Jingtang; Mao Yufang; Dong Xiaoli

    1997-01-01

    The experimental results on properties of the PbWO 4 crystal are reported, including the excitation and fluorescence spectra, absolute and relative light yield and decay times. It seems that the PbWO 4 crystal can be used in high energy physics experiments for detecting high energy shower particles

  16. Synthesis of chemically bonded BiOCl@Bi{sub 2}WO{sub 6} microspheres with exposed (0 2 0) Bi{sub 2}WO{sub 6} facets and their enhanced photocatalytic activities under visible light irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Ma, Yongchao [Qingdao Agricultural University, Qingdao 266109 (China); Chen, Zhiwei [School of Life Sciences, Shandong University of Technology, Zibo 255049 (China); Qu, Dan [Qingdao Agricultural University, Qingdao 266109 (China); Shi, Jinsheng, E-mail: jsshiqn@aliyun.com [Qingdao Agricultural University, Qingdao 266109 (China)

    2016-01-15

    Graphical abstract: - Highlights: • BiOCl@Bi{sub 2}WO{sub 6} composites were prepared via a controlled anion exchange method. • The shell of composites was composed of Bi{sub 2}WO{sub 6} sheets with exposed (0 2 0) facets. • The BiOCl@Bi{sub 2}WO{sub 6} composites showed efficient photocatalytic activity. • A possible photocatalytic degradation mechanism is proposed. - Abstract: Bi{sub 2}WO{sub 6} photocatalysts has been extensively studied for its photocatalytic activity. However, few works have been conducted on hierarchical Bi{sub 2}WO{sub 6} composite photocatalysts with specifically exposed facets. In this work, we report a facile method to synthesize BiOCl@Bi{sub 2}WO{sub 6} hierarchical composite microspheres. Bi{sub 2}WO{sub 6} nanosheets with specifically exposed (0 2 0) facet were directly formed on the surface of BiOCl precursor microspheres via a controlled anion exchange route between BiOCl and Na{sub 2}WO{sub 4}. The visible-light photocatalytic activity of the BiOCl@Bi{sub 2}WO{sub 6} heterojunction with exposed (0 2 0) facets (denoted as BiOCl@Bi{sub 2}WO{sub 6}) was investigated by degradation of Rhodamine B (RhB) and ciprofloxacin (CIP) aqueous solution under visible light irradiation. The experimental results indicated that the BiOCl@Bi{sub 2}WO{sub 6} composite microsphere with intimate interfacial contacts exhibited improved efficiency for RhB photodegradation in comparison with pure BiOCl and Bi{sub 2}WO{sub 6}. The BiOCl@Bi{sub 2}WO{sub 6} composite microsphere also shows high photocatalytic activity for degradation of CIP under visible light irradiation. The enhanced photocatalytic performance of BiOCl@Bi{sub 2}WO{sub 6}-020 hierarchical microspheres can be ascribed to the improved visible light harvesting ability, high charge separation and transfer. This work will make significant contributions toward the exploration of novel heterostructures with high potential in photocatalytic applications.

  17. Tungsten-based nanomaterials (WO{sub 3} & Bi{sub 2}WO{sub 6}): Modifications related to charge carrier transfer mechanisms and photocatalytic applications

    Energy Technology Data Exchange (ETDEWEB)

    Girish Kumar, S., E-mail: girichem@yahoo.co.in; Koteswara Rao, K.S.R., E-mail: raoksrk@gmail.com

    2015-11-15

    Graphical abstract: - Highlights: • Photocatalytic applications of WO{sub 3} and Bi{sub 2}WO{sub 6} based nanomaterial are reviewed. • Modifications to improve their performance are highlighted. • Charge carrier generation–separation–recombination is discussed. • Challenges and future prospects in this area are addressed. - Abstract: Heterogeneous photocatalysis is an ideal green energy technology for the purification of wastewater. Although titania dominates as the reference photocatalyst, its wide band gap is a bottleneck for extended utility. Thus, search for non-TiO{sub 2} based nanomaterials has become an active area of research in recent years. In this regard, visible light absorbing polycrystalline WO{sub 3} (2.4–2.8 eV) and Bi{sub 2}WO{sub 6} (2.8 eV) with versatile structure-electronic properties has gained considerable interest to promote the photocatalytic reactions. These materials are also explored in selective functional group transformation in organic reactions, because of low reduction and oxidation potential of WO{sub 3} CB and Bi{sub 2}WO{sub 6} VB, respectively. In this focused review, various strategies such as foreign ion doping, noble metal deposition and heterostructuring with other semiconductors designed for efficient photocatalysis is discussed. These modifications not only extend the optical response to longer wavelengths, but also prolong the life-time of the charge carriers and strengthen the photocatalyst stability. The changes in the surface-bulk properties and the charge carrier transfer dynamics associated with each modification correlating to the high activity are emphasized. The presence of oxidizing agents, surface modification with Cu{sup 2+} ions and synthesis of exposed facets to promote the degradation rate is highlighted. In depth study on these nanomaterials is likely to sustain interest in wastewater remediation and envisaged to signify in various green energy applications.

  18. Review of WO3 thin film preparation for photoelectrochemical water splitting

    International Nuclear Information System (INIS)

    Ehsan Eftekhari; Mohammad Kassim

    2009-01-01

    Full text: Tungsten trioxide (WO 3 ), which is one of the most essential materials in our daily life has appeared as an excellent photo electrode material for environmental purification. The nano-size of WO 3 thin film water-splitting technology has great potential for environmentally friendly solar-hydrogen production for the future hydrogen economy. There are several methods for producing tungsten oxide film. In this review, we outlined several WO 3 thin film preparation methods such as doctor Bladding, sputtering, layer-by-layer brush painting, spray pyrolysis deposition, sol-gel and other methods. Here we compare the maximum photocurrent obtained, different condition for preparation of WO 3 thin film and characterization outcome. (author)

  19. Biomimetic fabrication of WO{sub 3} for water splitting under visible light with high performance

    Energy Technology Data Exchange (ETDEWEB)

    Yin, Chao; Zhu, Shenmin, E-mail: smzhu@sjtu.edu.cn; Yao, Fan; Gu, Jiajun; Zhang, Wang [Shanghai Jiao Tong University, State Key Laboratory of Metal Matrix Composites (China); Chen, Zhixin [University of Wollongong, Faculty of Engineering (Australia); Zhang, Di, E-mail: zhangdi@sjtu.edu.cn [Shanghai Jiao Tong University, State Key Laboratory of Metal Matrix Composites (China)

    2013-08-15

    Inspired by the high light-harvesting properties of typical butterfly wings, ceramic WO{sub 3} butterfly wings with hierarchical structures of bio-butterfly wings was fabricated using a template of PapilioParis butterfly wings through a sol-gel method. The effect of calcination temperatures on the structures of the ceramic butterfly wings was investigated and the results showed that the WO{sub 3} butterfly wing replica calcined at 550 Degree-Sign C (WO{sub 3} replica-550) is a single phase and has a high crystallinity and relatively fine hierarchical structure. The average grain size of WO{sub 3} replica-550 and WO{sub 3} powder are around 32.6 and 42.2 nm, respectively. Compared with pure WO{sub 3} powder, WO{sub 3} replica-550 demonstrated a higher light-harvesting capability in the region from 460 to 700 nm and more importantly the higher charge separation rate, as evidenced by electron paramagnetic resonance measurements. Photocatalytic O{sub 2} evolutions from water were investigated on the ceramic butterfly wings and pure WO{sub 3} powder under visible light ({lambda} > 420 nm). The results showed that the amount of O{sub 2} produced from WO{sub 3} replica-550 is 50 % higher than that of the pure WO{sub 3} powder. The improved photocatalytic performance of WO{sub 3} replica-550 is attributed to the quasi-honeycomb structure inherited from the PapilioParis butterfly wings, providing both high light-harvesting efficiency and efficient charge transport through the WO{sub 3}.

  20. Residual radioactivity investigation and radiological assessments for self-disposal of concrete waste in nuclear fuel processing facility

    International Nuclear Information System (INIS)

    Seol, Jeung Gun; Ryu, Jae Bong; Cho, Suk Ju; Yoo, Sung Hyun; Song, Jung Ho; Baek, Hoon; Kim, Seong Hwan; Shin, Jin Seong; Park, Hyun Kyoun

    2007-01-01

    In this study, domestic regulatory requirement was investigated for self-disposal of concrete waste from nuclear fuel processing facility. And after self-disposal as landfill or recycling/reuse, the exposure dose was evaluated by RESRAD Ver. 6.3 and RESRAD BUILD Ver. 3.3 computing code for radiological assessments of the general public. Derived clearance level by the result of assessments for the exposure dose of the general public is 0.1071Bq/g (3.5% enriched uranium) for landfill and 0.05515 Bq/cm 2 (5% enriched uranium) for recycling/reuse respectively. Also, residual radioactivity of concrete waste after decontamination was investigated in this study. The result of surface activity is 0.01Bq/cm 2 for emitter and the result of radionuclide analysis for taken concrete samples from surface of concrete waste is 0.0297Bq/g for concentration of 238 U, below 2w/o for enrichment of 235 U and 0.0089Bq/g for artificial contamination of 238 U respectively. Therefore, radiological hazard of concrete waste by self-disposal as landfill and recycling/reuse is below clearance level to comply with clearance criterion provided for Notice No. 2001-30 of the MOST and Korea Atomic Energy Act

  1. Visible-light photocatalytic activity of graphene oxide-wrapped Bi{sub 2}WO{sub 6} hierarchical microspheres

    Energy Technology Data Exchange (ETDEWEB)

    Zhai, Jiali; Yu, Hongwen, E-mail: yuhw@iga.ac.cn; Li, Haiyan; Sun, Lei; Zhang, Kexin; Yang, Hongjun

    2015-07-30

    Graphical abstract: - Highlights: • GO/Bi{sub 2}WO{sub 6} are readily fabricated by facile bubbling pretreatment and freeze drying. • GO/Bi{sub 2}WO{sub 6} possess excellent photocatalytic activity under visible light irradiation. • The visible light activity of GO/Bi{sub 2}WO{sub 6} is affected by the amount of GO. • The photostablity of GO is due to the photo-generated electrons transfer to Bi{sub 2}WO{sub 6}. - Abstract: A facile approach of fabricating homogeneous graphene oxide (GO)-wrapped Bi{sub 2}WO{sub 6} microspheres (GO/Bi{sub 2}WO{sub 6}) is developed. The transmission electron microscopy (TEM) results show that a heterojunction interface between GO and Bi{sub 2}WO{sub 6}. The UV–vis diffuse reflection spectra (DRS) reveal that the as-prepared GO/Bi{sub 2}WO{sub 6} composites own more intensive absorption in the visible light range compared with pure Bi{sub 2}WO{sub 6}. These characteristic structural and optical properties endow GO/Bi{sub 2}WO{sub 6} composites with enhanced photocatalytic activity. The enhanced photocatalytic activity of the GO/Bi{sub 2}WO{sub 6} is attributed predominantly to the synergetic effect between GO and Bi{sub 2}WO{sub 6}, causing rapid generation and separation of photo-generated charge carriers.

  2. Optical properties of WO{sub 3} thin films using surface plasmon resonance technique

    Energy Technology Data Exchange (ETDEWEB)

    Paliwal, Ayushi; Sharma, Anjali; Gupta, Vinay, E-mail: drguptavinay@gmail.com, E-mail: vgupta@physics.du.ac.in [Department of Physics and Astrophysics, University of Delhi, Delhi 110007 (India); Tomar, Monika [Department of Physics, Miranda House, University of Delhi, Delhi 110007 (India)

    2014-01-28

    Indigenously assembled surface plasmon resonance (SPR) technique has been exploited to study the thickness dependent dielectric properties of WO{sub 3} thin films. WO{sub 3} thin films (80 nm to 200 nm) have been deposited onto gold (Au) coated glass prism by sputtering technique. The structural, optical properties and surface morphology of the deposited WO{sub 3} thin films were studied using X-ray diffraction, UV-visible spectrophotometer, Raman spectroscopy, and Scanning electron microscopy (SEM). XRD analysis shows that all the deposited WO{sub 3} thin films are exhibiting preferred (020) orientation and Raman data indicates that the films possess single phase monoclinic structure. SEM images reveal the variation in grain size with increase in thickness. The SPR reflectance curves of the WO{sub 3}/Au/prism structure were utilized to estimate the dielectric properties of WO{sub 3} thin films at optical frequency (λ = 633 nm). As the thickness of WO{sub 3} thin film increases from 80 nm to 200 nm, the dielectric constant is seen to be decreasing from 5.76 to 3.42, while the dielectric loss reduces from 0.098 to 0.01. The estimated value of refractive index of WO{sub 3} film is in agreement to that obtained from UV-visible spectroscopy studies. The strong dispersion in refractive index is observed with wavelength of incident laser light.

  3. Gas sensing properties of graphene–WO3 composites prepared by hydrothermal method

    International Nuclear Information System (INIS)

    Chu, Xiangfeng; Hu, Tao; Gao, Feng; Dong, Yongping; Sun, Wenqi; Bai, Linshan

    2015-01-01

    Graphical abstract: - Highlights: • The amount of graphene had an effect on the morphology of graphene–WO 3 composites. • The optimum temperature of 0.1 wt% graphene–WO 3 sensor to acetaldehyde was 100 °C. • 0.1 wt% graphene–WO 3 sensor exhibited good selectivity to acetaldehyde at 100 °C. - Abstract: Graphene–WO 3 composites mixed with different amounts of graphene (0, 0.1, 0.5, 1 and 3 wt%) were prepared by hydrothermal method at 180 °C for 24 h. The as-prepared graphite oxide, graphene and graphene–WO 3 composites were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), Fourier transform infrared spectra (FT-IR) and Raman spectroscopy, respectively. The effect of the amount of graphene in the composites on the gas-sensing responses and the gas-sensing selectivity of the materials was investigated. The experimental results revealed that the sensor based on 0.1 wt% graphene–WO 3 composite exhibited high response and good selectivity to acetaldehyde vapor at 100 °C, the optimum operating temperature of this sensor to 1000 ppm acetaldehyde vapor decreased from 180 °C to 100 °C comparing with that of pure WO 3 . The response time and the recovery time for 100 ppm acetaldehyde vapor were 250 s and 225 s, respectively

  4. Preparation of WO3/g-C3N4 composites and their application in oxidative desulfurization

    International Nuclear Information System (INIS)

    Zhao, Rongxiang; Li, Xiuping; Su, Jianxun; Gao, Xiaohan

    2017-01-01

    Highlights: • The WO 3 /g-C 3 N 4 was successfully synthesized through simple calcination. • The process is simple and the cost raw materials is cheap. • The WO 3 /g-C 3 N 4 firstly applied to ODS. • The desulpurization rate of WO 3 /g-C 3 N 4 may attach to 91.2%. • Five recycles of WO 3 /g-C 3 N 4 still attach to 89.5% due to heterogeneous catalysis. - Abstract: WO 3 /graphitic carbon nitride (g-C 3 N 4 ) composites were successfully synthesized through direct calcining of a mixture of WO 3 and g-C 3 N 4 at 400 °C for 2 h. The WO 3 was prepared by calcination of phosphotungstic acid at 550 °C for 4 h, and the g-C 3 N 4 was obtained by calcination of melamine at 520 °C for 4 h. The WO 3 /g-C 3 N 4 composites were characterized by X-ray diffraction (XRD), Scanning electron microscopy (SEM), Fourier-transform infrared spectroscopy (FT-IR), and Brunner−Emmett−Teller analysis (BET). The WO 3 /g-C 3 N 4 composites exhibited stronger XRD peaks of WO 3 and g-C 3 N 4 than the WO 3 and pure g-C 3 N 4 . In addition, two WO 3 peaks at 25.7° and 26.6° emerged for the 36% −WO 3 /g-C 3 N 4 composite. This finding indicated that WO 3 was highly dispersed on the surface of the g-C 3 N 4 nanosheets and interacted with the nanosheets, which resulted in the appearance of (012) and (022) planes of WO 3 . The WO 3 /g-C 3 N 4 composite also exhibited a larger specific surface area and higher degree of crystallization than WO 3 or pure g-C 3 N 4 , which resulted in high catalytic activity of the catalyst. Desulfurization experiments demonstrated that the desulfurization rate of dibenzothiophene (DBT) in model oil reached 91.2% under optimal conditions. Moreover, the activity of the catalyst was not significantly decreased after five recycles.

  5. Structure, electrochromic and optical properties of WO3 film prepared by dip coating-pyrolysis

    International Nuclear Information System (INIS)

    Yang Haitao; Shang Fuliang; Gao Ling; Han Haitao

    2007-01-01

    The tungsten oxide (WO 3 ) film was grown by dip coating-pyrolysis method with the PEG-400 as the structure-directing agent. Microstructure of the WO 3 film was characterized by TG-DSC, XRD and SEM techniques. It was found that the film annealed at 350 deg. C for 2 h comprised cubic WO 3 and orthorhombic WO 3 . The measurements of the cyclic voltammetry (CV) and UV-vis spectrum suggested that the WO 3 film had a good electrochromic reversibility performance. The film possessed excellent modulation to the visible light and the maximal average transmittance modulation reached 70.06%

  6. CW lasing of Ho in KLu(WO4)2 in-band pumped by a diode-pumped Tm:KLu(WO4)2 laser.

    Science.gov (United States)

    Mateos, Xavier; Jambunathan, Venkatesan; Pujol, Maria Cinta; Carvajal, Joan Josep; Díaz, Francesc; Aguiló, Magdalena; Griebner, Uwe; Petrov, Valentin

    2010-09-27

    We demonstrate continuous wave (CW) room temperature laser operation of the monoclinic Ho(3+)-doped KLu(WO(4))(2) crystal using a diode-pumped Tm(3+):KLu(WO(4))(2) laser for in-band pumping. The slope efficiency achieved amounts to ~55% with respect to the absorbed power and the maximum output power of 648 mW is generated at 2078 nm.

  7. Correlations among structure, composition and electrochemical performances of WO3 anode materials for lithium ion batteries

    International Nuclear Information System (INIS)

    Li, Pu; Li, Xing; Zhao, Ziyan; Wang, Mingshan; Fox, Thomas; Zhang, Qian; Zhou, Ying

    2016-01-01

    Highlights: • The residual precursor ions affect the charge/discharge performances of WO 3 . • Lithiated monoclinic WO 3 reveals the best discharge capacity. • Lithiation can enhance the conductivity of WO 3 . - Abstract: Suitable host structure for lithium insertion and extraction is crucial for lithium-ion batteries. Tungsten trioxides (WO 3 ) are particularly interesting materials for this purpose. In this work, the influences of structure and composition of WO 3 on the charge/discharge performances of Li-ion batteries are systematically investigated. Firstly, lithiated tungsten trioxides (Li-WO 3 ) are successfully synthesized by a hydrothermal method followed by annealing at different temperatures (200–600 °C). It is found that the hexagonal framework collapses and gradually transforms to the monoclinic phase due to the release of NH 4 + and NH 3 molecules. Unexpectedly, monoclinic WO 3 reveals better performances than that of hexagonal WO 3 . Among all the investigated samples, the lithiated WO 3 annealed at 500 °C exhibits the highest discharge capacity and cycle performance (703 mAh g −1 after 10 cycles). We believe that the Li + remained in the solid structure of WO 3 can lead to a more stable structure. In addition, Li + could inhibit the oxidation of W 5+ during the heat treatment process, which increases the electron conductivity of WO 3 . Our results indicate that the electrochemical properties of WO 3 are strongly related to the residual precursor and crystal structure.

  8. Proposal and study of a long-span composite cable-stayed bridge with new hybrid girder; Atarashii gosei kozo shuketa wo mochiita chodai fukugo shachokyo no kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Yoshida, K.; Hishiki, Y.; Furuichi, K. [Kajima Corp., Tokyo (Japan)

    1999-09-30

    A hybrid or mixed structure (composite structures) are a matter of increasing concern which takes in each advantage of steel and concrete. A field of bridges is no exception, with the plan and construction carried out for the new type of composite bridge, such as a composite cable-stayed bridge and a composite extra dose bridge as a long span bridge, and a composite truss bridge and a corrugated steel plate web bridge as a medium-span bridge, with technological development becoming active in this field. In such a technological trend, a hybrid two-girder structure was devised, a structure consisting of a concrete filled steel pipe for a girder and a precast (PC) floor plate for a floor board, as the girder structure of a long-span cable-stayed bridge in the subject research; also, applicability was examined using, as an example, the composite cable-stayed bridge with hybrid girders employed for the span. This paper reports the result of the analysis of the entire system, the analysis made for the purpose of examining the characteristic and the feasibility of this hybrid girder. The analysis revealed the structural feasibility of the long-span composite cable-stayed bridge using two hybrid girders of concrete-filled steel pipes thus devised. (NEDO)

  9. Preparation of WO3/g-C3N4 composites and their application in oxidative desulfurization

    Science.gov (United States)

    Zhao, Rongxiang; Li, Xiuping; Su, Jianxun; Gao, Xiaohan

    2017-01-01

    WO3/graphitic carbon nitride (g-C3N4) composites were successfully synthesized through direct calcining of a mixture of WO3 and g-C3N4 at 400 °C for 2 h. The WO3 was prepared by calcination of phosphotungstic acid at 550 °C for 4 h, and the g-C3N4 was obtained by calcination of melamine at 520 °C for 4 h. The WO3/g-C3N4 composites were characterized by X-ray diffraction (XRD), Scanning electron microscopy (SEM), Fourier-transform infrared spectroscopy (FT-IR), and Brunner-Emmett-Teller analysis (BET). The WO3/g-C3N4 composites exhibited stronger XRD peaks of WO3 and g-C3N4 than the WO3 and pure g-C3N4. In addition, two WO3 peaks at 25.7° and 26.6° emerged for the 36% -WO3/g-C3N4 composite. This finding indicated that WO3 was highly dispersed on the surface of the g-C3N4 nanosheets and interacted with the nanosheets, which resulted in the appearance of (012) and (022) planes of WO3. The WO3/g-C3N4 composite also exhibited a larger specific surface area and higher degree of crystallization than WO3 or pure g-C3N4, which resulted in high catalytic activity of the catalyst. Desulfurization experiments demonstrated that the desulfurization rate of dibenzothiophene (DBT) in model oil reached 91.2% under optimal conditions. Moreover, the activity of the catalyst was not significantly decreased after five recycles.

  10. A simple synthesis of MnWO{sub 4} nanoparticles as a novel energy storage material

    Energy Technology Data Exchange (ETDEWEB)

    Li, Feihui, E-mail: feihuili2012@163.com [Department of Applied Chemistry, School of Science, Tianjin University of Commerce, Tianjin 300134 (China); Xu, Xiaoyang, E-mail: xiaoyangxu2012@163.com [School of Science, Tianjin University (China); Huo, Jialei; Wang, Wei [School of Chemical Engineering, Tianjin 300072 (China)

    2015-11-01

    MnWO{sub 4} nanoparticles with the shuttle-like shape were prepared by a simple chemical co-precipitation method and analyzed by X-ray diffraction, transmission electron microscopy and X-ray photoelectron spectroscopy. The prepared MnWO{sub 4} was used as the electrode material of a supercapacitor, and its electrochemical performance was studied using cyclic voltammetry, galvanostatic charge/discharge cycles and electrochemical impedance spectroscopy. The MnWO{sub 4} exhibited good electrochemical performance. The MnWO{sub 4} nanoparticles had specific capacitances of 295 F/g at a scan rate of 5 mV/s and 219 F/g at a current density of 0.4 A/g. They also showed good cycle-life stability and low resistance. Therefore, MnWO{sub 4} is a promising electrode material for supercapacitors. - Highlights: • The shuttle-like MnWO{sub 4} nanoparticles have been prepared. • The prepared MnWO{sub 4} nanoparticles exhibit good electrochemical performances. • MnWO{sub 4} is a promising electrode material for supercapacitors.

  11. Porous three-dimensional reduced graphene oxide merged with WO3 for efficient removal of radioactive strontium

    Science.gov (United States)

    Mu, Wanjun; Yu, Qianghong; Hu, rui; Li, Xingliang; Wei, Hongyuan; Jian, Yuan

    2017-11-01

    A simple hydrothermal method was used to prepare 3D nanostructured composite adsorbents of reduced graphene oxide (RGO) and WO3 (RGO/WO3). The analysis results suggest that it possesses a mesoporous 3D structure, in which WO3 nanorods are uniformly loaded on the surface of the RGO. Combining the benefits of GO and WO3, the composites exhibit a higher adsorption capacity for removing Sr2+ from aqueous solutions over a wide pH range (4-11). Adsorption isotherms show that the data fit the Langmuir isotherms well (R > 0.99), and the maximum adsorption capacity of 149.56 mg g-1 was achieved, much higher than that for GO, WO3 and other similar adsorbents. Sr2+ adsorption on RGO/WO3 reached equilibrium within 200 min. The fast adsorption and high adsorption rate of RGO/WO3 are mostly attributable to the plentiful adsorption sites provided by the dispersed WO3 nanoparticles on the RGO surface. Furthermore, the existence of Na+ ions has no obvious effect on the removal of Sr2+ ions by RGO/WO3, and RGO/WO3 adsorbent can be repeated at least 5 times without significant loss of adsorption capacity by adsorption-desorption experiment. Thus, RGO/WO3 shows the potential ability for removal of 90Sr from radioactive wastewater.

  12. Physical properties characterization of WO3 films grown by hot-filament metal oxide deposition

    International Nuclear Information System (INIS)

    Diaz-Reyes, J.; Delgado-Macuil, R.J.; Dorantes-Garcia, V.; Perez-Benitez, A.; Balderas-Lopez, J.A.; Ariza-Ortega, J.A.

    2010-01-01

    WO 3 is grown by hot-filament metal oxide deposition (HFMOD) technique under atmospheric pressure and an oxygen atmosphere. By X-ray diffraction obtains that WO 3 presents mainly monoclinic crystalline phase. The chemical stoichiometry is obtained by X-ray Photoelectron Spectroscopy (XPS). The IR spectrum of the as-grown WO 3 presents broad peaks in the range of 1100 to 3600 cm -1 . A broad band in the 2200 to 3600 cm -1 region and the peaks sited at 1645 and 1432 cm -1 are well resolved, which are originated from moisture and are assigned to ν(OH) and δ(OH) modes of adsorbed water and the corresponding tungsten oxide vibrations are in infrared region from 400 to 1453 cm -1 and around 3492 cm -1 , which correspond to tungsten-oxygen (W-O) stretching, bending and lattice modes. The Raman spectrum shows intense peaks at 801, 710, 262 and 61 cm -1 that are typical Raman peaks of crystalline WO 3 (m-phase) that correspond to stretching vibrations of the bridging oxygen, which are assigned to W-O stretching (ν) and W-O bending (δ) modes, respectively. By transmittance measurements obtains that the WO 3 band gap can be varied from 2.92 to 3.13 eV in the investigated annealing temperature range.

  13. Pronounced effects of the nominal concentrations of WO3 and Ag: WO3 nano-plates (obtained by a co-precipitation method) on their structural, morphological and optical properties

    Science.gov (United States)

    Rajendran, V.; Deepa, B.

    2018-03-01

    Tungsten oxide and different concentration of silver (Ag)-doped tungsten oxide nano material were synthesized by co-precipitation technique. The functional vibrations, structure, and morphology of as-prepared nano material were studied by Fourier transmission infrared spectroscopy, X-ray diffraction, scanning electron microscopy (SEM) and High-resolution transmission electron microscopy (HR-TEM) techniques. The SEM and HR-TEM analysis revealed the formation of nano-plate/nano rods with an average diameter of 40-80 nm diameter and 1-1.5 mm length. Fluorescence (PL) and UV-visible absorption techniques have been used to study the optical properties of the prepared nanoparticles. The observed red shift in the visible absorption spectra confirmed the promoted electron-phonon interaction in WO3 and Ag: WO3 nanoparticles compared to bulk structures. The photoluminescence of nanocrystalline Ag2+ doped WO3 exhibited a strong violet-blue, blue-green emission. Concentration dependence of the emission intensity of Ag2+ in WO3 was studied, and the significant concentration was found to be 0.5% of Ag: WO3. The effluent dye degradation executed for the 0.5% of Ag: WO3 sample under the visible light which reveals the highest degradation efficiency in appropriate time.

  14. Template-free hydrothermal synthesis and high photocatalytic activity of ZnWO4 nanorods

    International Nuclear Information System (INIS)

    Gao, Bin; Fan, Huiqing; Zhang, Xiaojun; Song, Lixun

    2012-01-01

    Highlights: ► ZnWO 4 nanorods with uniform diameter are successfully prepared through a template-free hydrothermal method. ► The crystallinity of the products is influenced by the pH value of initial precursor suspension. ► Photocatalytic activity of the ZnWO 4 nanorods for degradation of methylene blue is evaluated. ► The ZnWO 4 nanorods exhibit good stability of photocatalytic activity. - Abstract: ZnWO 4 nanorods are successfully synthesized by a template-free hydrothermal method, and are characterized in detail by X-ray diffractometer (XRD), transmission electron microscopy (TEM), high-resolution transmission electron microscopy (HRTEM) and selected area electron diffraction (SAED). The results show that the ZnWO 4 nanorods with wolframite structure are well-crystallized single crystallites. The crystallinity of the products is influenced by the pH value of initial precursor suspension. The width and length of the synthesized samples increase with hydrothermal reaction temperature. The photocatalytic efficiency of the ZnWO 4 nanorods for degradation of methylene blue (MB) in aqueous solution under UV light irradiation declines greatly with increasing crystallinity. The ZnWO 4 nanorods prepared at pH of 4 have the best activity in photo-degradation of MB. After six recycles, photocatalytic activity loss of the catalyst is not obvious.

  15. AOT-microemulsions-based formation and evolution of PbWO$_{4}$ crystals

    CERN Document Server

    Chen, D; Tang Kai Bin; Liang Zhen Hua; Zheng Hua Gui

    2004-01-01

    Anionic surfactant-AOT-microemulsions-assisted formation and evolution of PbWO//4 nanostructures with bundles rodlike, ellipsoidlike, and spherelike prepared at different media conditions were studied by powder X-ray diffraction pattern, field emission scanning electron microscopy, and transmission electron microscopy. The possible mechanisms for the formation of PbWO//4 samples in series of microemulsion systems were discussed. Various comparison experiments show that several experimental parameters, such as the AOT concentration, the water content, and reaction temperature play important roles in the morphological control of PbWO//4 nanostructures. Room-temperature photoluminescence of PbWO//4 samples with different morphologies has also been investigated and the results reveal that all these samples showed similar features with emissions at 480 similar to 510 nm but different luminescence intensity. 40 Refs.

  16. Facile synthesis of reduced graphene oxide/CoWO4 nanocomposites with enhanced electrochemical performances for supercapacitors

    International Nuclear Information System (INIS)

    Xu, Xiaowei; Shen, Jianfeng; Li, Na; Ye, Mingxin

    2014-01-01

    Highlights: • RGO/CoWO 4 composites were successfully prepared through a facile hydrothermal method. • RGO/CoWO 4 composites show much higher specific capacitances than pure CoWO 4 . • Enhanced electrical conductivity leads to superior electrochemical performance. - Abstract: A facile one-pot hydrothermal method was provided for synthesis of the reduced graphene oxide-cobalt tungstate (RGO/CoWO 4 ) nanocomposites with the enhanced electrochemical performances for supercapacitors for the first time. The resulting nanocomposites are comprised of CoWO 4 nanospheres that are well-anchored on graphene sheets by in situ reducing. The prepared RGO/CoWO 4 nanocomposites have been thoroughly characterized by Fourier–transform infrared spectroscopy, X-ray diffraction, Raman spectroscopy, Thermogravimetric analysis, Scanning electron microscopy, Transmission electron microscopy, X-ray photoelectron spectroscopy, and N 2 adsorption–desorption. Importantly, the prepared nanocomposites exhibit superior electrochemical performance to CoWO 4 as electrodes for supercapacitors. As a result, RGO/CoWO 4 nanocomposites with 91.6 wt% CoWO 4 content achieved a specific capacitance about 159.9 F g −1 calculated from the CV curves at 5 mV s −1 , which was higher than that of CoWO 4 (60.6 F g −1 ). The good electrochemical performance can be attributed to the increased electrical conductivity and the creation of new active sites due to the synergetic effect of RGO and CoWO 4 nanospheres. The cyclic stability tests demonstrated capacitance retention of about 94.7% after 1000 cycles, suggesting the potential application of RGO/CoWO 4 nanocomposites in energy-storage devices

  17. Super-Nernstian pH sensors based on WO3 nanosheets

    Science.gov (United States)

    Kuo, Chao-Yin; Wang, Shui-Jinn; Ko, Rong-Ming; Tseng, Hung-Hao

    2018-04-01

    The effects of the surface morphology of hydrothermally grown WO3 nanosheets (NSs) and sputtering WO3 film on the performance of pH sensing electrodes are presented and compared in the pH range of 2–12. Using a separated electrode of an extended-gate field-effect transistor (EGFET) configuration, the WO3 nanosheet (NS) pH sensor shows a sensitivity of 63.37 mV/pH, a good linearity of 0.9973, a low voltage hysteresis of 4.79 mV, and a low drift rate of 3.18 mV/h. In contrast, the film-type one shows a typical sensitivity of only 50.08 mV/pH and a linearity of 0.9932. The super-Nernstian response could be attributed to the significant increase in the number of surface ion adsorption sites of the NS structure and the occurrence of local electric field enhancement over the sharp edges and corners of WO3 NSs.

  18. Enhancement of visible-light photocatalytic activity of silver and mesoporous carbon co-modified Bi2WO6

    International Nuclear Information System (INIS)

    Zhao, Qian; Gong, Ming; Liu, Wangping; Mao, Yulin; Le, Shukun; Ju, Shang; Long, Fei; Liu, Xiufang; Liu, Kai; Jiang, Tingshun

    2015-01-01

    Graphical abstract: - Highlights: • Silver and mesoporous carbon co-modified Bi 2 WO 6 (Ag/Bi 2 WO 6 /CMK-3) composite was prepared. • Photocatalytic activity of Bi 2 WO 6 was remarkably enhanced by co-modification of silver and mesoporous carbon. • The degradation rate of MB can reach ca. 95.1% under visible light irradiation. • The Ag/Bi 2 WO 6 /CMK-3 composite has good stability and potential application prospects. - Abstract: Ordered mesoporous carbon CMK-3 was prepared by hard template method using SBA-15 as template, sucrose as carbon source. Flower/sphere-like Bi 2 WO 6 and CMK-3/Bi 2 WO 6 photocatalysts were synthesized by hydrothermal method, and then Ag/Bi 2 WO 6 and Ag/Bi 2 WO 6 /CMK-3 composite photocatalysts were prepared via a photoreduction process. The samples were characterized by XRD, UV–vis, TEM (HR-TEM), SEM, N 2 physical adsorption and PL and their photocatalytic activities were evaluated by the photocatalytic degradation of methylene blue (MB) under visible light irradiation. The results show that both incorporating of CMK-3 and Ag loading greatly improved the photocatalytic activity of Bi 2 WO 6 , and the content of CMK-3 and silver have an impact on the photocatalytic activity of Bi 2 WO 6 . The photocatalytic activity of Ag/Bi 2 WO 6 /CMK-3 photocatalyst is superior to the activities of CMK-3/Bi 2 WO 6 and Ag/Bi 2 WO 6 under comparable conditions, and Ag/Bi 2 WO 6 /CMK-3 photocatalyst has high stability and is easy to be recycled. Also, the mechanism for the enhancement of the photocatalytic activity of CMK-3 and Ag co-modified Bi 2 WO 6 was also investigated

  19. Hydrothermal synthesis of CdWO 4 nanorods and their ...

    African Journals Online (AJOL)

    CdWO4 nanorods with wolframite structure were synthesized in the presence of the surfactant SDBS by a hydrothermal method, and characterized by a variety of techniques. The obtained products are CdWO4 nanorods with length of 0.8–2.5 μm and width of 50–250 nm. The surfactant SDBS plays a key role in the ...

  20. Synthesis, characterization and photocatalytic activity of porous WO3/TiO2 hollow microspheres

    International Nuclear Information System (INIS)

    Yang, Liuyang; Si, Zhichun; Weng, Duan; Yao, Youwei

    2014-01-01

    Porous WO 3 /TiO 2 hollow microspheres were prepared by a spray drying method for photodegradation of methylene blue and phenol. The catalysts were characterized by X-ray diffraction, Field Emission Scanning Electron Microscope, High Resolution Transmission Electron Microscope, N 2 adsorption–desorption measurements, Raman spectrometer, UV–Vis Diffuse Reflectance Spectroscopy and Zeta-Meter measurements. The results showed that the tungsten oxides mainly existed in highly dispersed amorphous form on anatase when the loading amount of tungsten oxide was below 3 mol%. The improved photocatalytic activity under UV light irradiation of the WO 3 /TiO 2 catalyst mainly arises from the enhanced charge separation efficiency rather than the improved light absorbance by highly dispersed amorphous tungsten oxides. Highly dispersed amorphous WO x can form a shallowly trapped site due to its similar band structure with TiO 2 . The strongly electron-withdrawing of tungsten oxide in highly dispersed state facilitates the electron transition between titanium and WO x , and consequently improves the charge separation. The enhanced acidity of catalyst by WO x in reactant environment also improved the charge separation efficiency due to the timely transition of holes and electrons accumulated on TiO 2 and WO x , respectively. However, the improved photocatalytic activity under visible light irradiation of the WO 3 /TiO 2 catalyst mainly arises from light harvest. TiO 2 containing 3 mol% WO 3 displayed the highest photocatalytic activity under UV light irradiation while that containing 4 mol% WO 3 present highest activity under visible light irradiation

  1. A Resistive Humidity Sensor Based on Nanostructured WO3-ZnO Composites

    Directory of Open Access Journals (Sweden)

    Karunesh Tiwari

    2011-11-01

    Full Text Available Paper reports morphological and humidity sensing studies of WO3 and WO3-ZnO composite pellets prepared in the weight % ratio of 10:1, 4:1 and 2:1 by solid-state reaction route. The pellets have been annealed at temperatures of 300-500 °C. XRD pattern shows peaks of ZnWO4 formed due to solid state reaction between WO3 and ZnO. SEM micrographs show that the sensing elements manifest porous structure. Granulation and tendency to agglomerate seen in the SEM micrograph are due to the presence of zinc ions in ZnWO4. Nanoparticles are having their sizes in the range 37-182 nm. The average Kelvin radius at 20˚C room temperature is 27 Ả. Humidity sensing application of the pellets has been studied in a humidity control cabinet. It is observed that as relative humidity increases, there is decrease in the resistance of pellets in the range 10-85 % RH. Sensing element of WO3-ZnO in 2:1 weight % ratio shows best results in 10-85 % relative humidity range. The average sensitivity of this sample is 1.25 MΩ/%RH. This sensing element shows good reproducibility, low hysteresis and less effect of aging.

  2. Morphologically different WO3 nanocrystals in photoelectrochemical water oxidation

    International Nuclear Information System (INIS)

    Biswas, Soumya Kanti; Baeg, Jin-Ook; Moon, Sang-Jin; Kong, Ki-jeong; So, Won-Wook

    2012-01-01

    Different morphologies of WO 3 nanocrystals such as nanorods and nanoplates have been obtained under hydrothermal conditions using ammonium metatungstate as the precursor in presence of different organic acids such as citric, oxalic, and tartaric acid in the reaction medium. Detailed characterization of the crystal structure, particle morphology, and optical band gap of the synthesized powders have been done by X-ray diffraction, transmission electron microscopy, scanning electron microscopy and solid-state UV–visible spectroscopy study. The as-synthesized materials are WO 3 hydrates with orthorhombic phase which transform to the hexagonal WO 3 through dehydration upon heating at 350 °C. The resultant products are crystalline with nanoscale dimensions. Finally, the photoactivity of the synthesized materials annealed at 500 °C has been compared employing in photoelectrochemical water oxidation under the illumination of AM 1.5G simulated solar light (100 mWcm −2 ). The photocurrent measurements upon irradiation of light exhibit obvious photocatalytic activity with a photocurrent of about 0.77, 0.61, and 0.65 mAcm −2 for the WO 3 film derived with the oxalic acid, tartaric, and citric acid assisting agents, respectively, at 1.8 V versus Ag/AgCl electrode.

  3. Improved electrochromical properties of sol-gel WO3 thin films by doping gold nanocrystals

    International Nuclear Information System (INIS)

    Naseri, N.; Azimirad, R.; Akhavan, O.; Moshfegh, A.Z.

    2010-01-01

    In this investigation, the effect of gold nanocrystals on the electrochromical properties of sol-gel Au doped WO 3 thin films has been studied. The Au-WO 3 thin films were dip-coated on both glass and indium tin oxide coated conducting glass substrates with various gold concentrations of 0, 3.2 and 6.4 mol%. Optical properties of the samples were studied by UV-visible spectrophotometry in a range of 300-1100 nm. The optical density spectra of the films showed the formation of gold nanoparticles in the films. The optical bandgap energy of Au-WO 3 films decreased with increasing the Au concentration. Crystalline structure of the doped films was investigated by X-ray diffractometry, which indicated formation of gold nanocrystals in amorphous WO 3 thin films. X-ray photoelectron spectroscopy (XPS) was used to study the surface chemical composition of the samples. XPS analysis indicated the presence of gold in metallic state and the formation of stoichiometric WO 3 . The electrochromic properties of the Au-WO 3 samples were also characterized using lithium-based electrolyte. It was found that doping of Au nanocrystals in WO 3 thin films improved the coloration time of the layer. In addition, it was shown that variation of Au concentration led to color change in the colored state of the Au-WO 3 thin films.

  4. NO{sub 2} gas sensing of flame-made Pt-loaded WO{sub 3} thick films

    Energy Technology Data Exchange (ETDEWEB)

    Samerjai, Thanittha [Nanoscience and Nanotechnology Program, Faculty of Graduate School, Chiang Mai University, Chiang Mai 50200 (Thailand); Tamaekong, Nittaya [Program in Materials Science, Faculty of Science, Maejo University, Chiang Mai 50290 (Thailand); Liewhiran, Chaikarn [Department of Physics and Materials Science, Faculty of Science, Chiang Mai University, Chiang Mai 50200 (Thailand); Wisitsoraat, Anurat [Nanoelectronics and MEMS Laboratory, National Electronics and Computer Technology Center, Klong Luang, Pathumthani 12120 (Thailand); Phanichphant, Sukon, E-mail: sphanichphant@yahoo.com [Materials Science Research Center, Faculty of Science, Chiang Mai University, Chiang Mai 50200 (Thailand)

    2014-06-01

    Unloaded WO{sub 3} and 0.25–1.0 wt% Pt-loaded WO{sub 3} nanoparticles for NO{sub 2} gas detection were synthesized by flame spray pyrolysis (FSP) and characterized via X-ray diffraction (XRD), scanning electron microscopy (SEM) and high resolution transmission electron microscopy (HRTEM). The BET surface area (SSA{sub BET}) of the nanoparticles was measured by nitrogen adsorption. The NO{sub 2} sensing properties of the sensors based on unloaded and Pt-loaded WO{sub 3} nanoparticles were investigated. The results showed that the gas sensing properties of the Pt-loaded WO{sub 3} sensors were excellent to those of the unloaded one. Especially, 0.25 wt% Pt-loaded WO{sub 3} sensor showed highest response to NO{sub 2} than the others at low operating temperature of 150 °C. - Graphical abstract: The response of 0.25 wt% Pt-loaded WO3 sensor was 637 towards NO{sub 2} concentration of 10 ppm at 150 °C. - Highlights: • Unloaded and Pt-loaded WO{sub 3} nanoparticles for NO{sub 2} gas detection were synthesized by flame spray pyrolysis (FSP). • Gas sensing properties of the Pt-loaded WO{sub 3} sensors were excellent to those of the unloaded one. • 0.25 wt% Pt-loaded WO{sub 3} sensor showed highest response to NO{sub 2} at low operating temperature of 150 °C.

  5. Combustion synthesized hierarchically porous WO{sub 3} for selective acetone sensing

    Energy Technology Data Exchange (ETDEWEB)

    Dong, Chengjun; Liu, Xu; Guan, Hongtao; Chen, Gang; Xiao, Xuechun [Department of Materials Science and Engineering, Yunnan University, 650091, Kunming (China); Djerdj, Igor [Ruđer Bošković Institute, Bijenička 54, 10000, Zagreb (Croatia); Wang, Yude, E-mail: ydwang@ynu.edu.cn [Department of Materials Science and Engineering, Yunnan University, 650091, Kunming (China); Yunnan Province Key Lab of Mico-Nano Materials and Technology, Yunnan University, 650091, Kunming (China)

    2016-12-01

    An easy, inexpensive combustion route was designed to synthesize hierarchically porous WO{sub 3}. The tungsten source was fresh peroxiotungstic acid by dissolving tungsten powder into hydrogen peroxide. To promote the combustion reaction, a combined fuel of both glycine and hydrazine hydrate was used. The microstructure was well-connected pores comprised of subunit nanoparticles. Upon exposing towards acetone gas, the porous WO{sub 3} based sensor exhibits high gas response, rapid response and recovery, and good selectivity in the range of 5–1000 ppm under working temperature of 300 °C. This excellent sensing performance was plausibly attributed to the porous morphology, which hence provides more active sites for the gas molecules' reaction. - Graphical abstract: Hierarchically porous WO{sub 3} synthesized by combustion process exhibits high gas response, rapid response and recovery, and excellent selectivity for acetone, making it to be promising candidates for practical detectors for acetone. - Highlights: • Hierarchically porous WO{sub 3} synthesized by combustion process. • Hierarchically porous WO{sub 3} exhibits high gas response and excellent selectivity for acetone. • The excellent sensing property was plausibly attributed to the porous morphology.

  6. Visible-light photocatalytic activity of Ag2O coated Bi2WO6 hierarchical microspheres assembled by nanosheets

    International Nuclear Information System (INIS)

    Chen, Lin; Hua, Hao; Yang, Qi; Hu, Chenguo

    2015-01-01

    Graphical abstract: - Highlights: • Bi 2 WO 6 hierarchical microspheres assembled by nanosheets and dispersed nanosheets are synthesized. • Ag 2 O/Bi 2 WO 6 heterostuctures exhibites an enhanced photocatalytic activity compared with the Bi 2 WO 6 nanostructures. • Photocatalytic activity of the Ag 2 O/Bi 2 WO 6 microspheres is higher than that of the nanosheets. • Bi 2 WO 6 hierarchical structure is an excellent architecture for loading of Ag 2 O nanoparticles. - Abstract: Bi 2 WO 6 hierarchical microspheres assembled by nanosheets and dispersed nanosheets were synthesized by hydrothermal reaction in different conditions. Ag 2 O nanoparticles were deposited on the surface of Bi 2 WO 6 microspheres and nanosheets by the chemical precipitation method. The photocatalytic performance of pure Bi 2 WO 6 nanostructures and Ag 2 O/Bi 2 WO 6 heterostructures were evaluated by the photocatalytic decolorization of RhB solution under visible-light irradiation. Compared with the pure Bi 2 WO 6 nanostructures, the Ag 2 O/Bi 2 WO 6 heterostructures exhibited an obviously enhanced photocatalytic activity. And photocatalytic activity of the Ag 2 O/Bi 2 WO 6 microspheres is higher than that of the Ag 2 O/Bi 2 WO 6 nanosheets. This work demonstrates that the Bi 2 WO 6 hierarchical three-dimensional structure is an excellent architecture for the loading of Ag 2 O nanoparticles to build a highly efficient photocatalyst

  7. Conductive surface modification of cauliflower-like WO3 and its electrochemical properties for lithium-ion batteries

    International Nuclear Information System (INIS)

    Yoon, Sukeun; Woo, Sang-Gil; Jung, Kyu-Nam; Song, Huesup

    2014-01-01

    Highlights: • Synthesis of cauliflower-like carbon-decorated WO 3 . • Superior cyclability and rate capability for cauliflower-like carbon-decorated WO 3 . • Electrochemical reaction behavior of cauliflower-like carbon-decorated WO 3 with lithium. • In-situ XRD analysis during the first discharge–charge shows a complex reaction of intercalation and conversion of WO 3 . - Abstract: Cauliflower-like WO 3 was synthesized by a hydrothermal reaction without a surfactant, followed by firing, and was investigated as an anode material for lithium-ion battery applications. The scanning electron microscope (SEM) and transmission electron microscope (TEM) characterization indicated that WO 3 nanorods had an aggregation framework and built a cauliflower morphology. With the objective of understanding the charge–discharge process within a voltage range of 0–3 V vs. Li + /Li, in situ X-ray diffraction was used and a complex reaction of intercalation and conversion of WO 3 was revealed for the first time. The cauliflower-like WO 3 after being decorated with carbon provides a high gravimetric capacity of >635 mA h/g (Li 5.5 WO 3 ) with good cycling and a high rate capability when used as an anode in lithium-ion batteries. Based on our studies, we attribute the high electrochemical performance to the nanoscopic WO 3 particles and a conductive carbon layer, which makes them a potential candidate for lithium-ion batteries

  8. Preparation of tungsten coatings on graphite by electro-deposition via Na2WO4–WO3 molten salt system

    International Nuclear Information System (INIS)

    Sun, Ning-bo; Zhang, Ying-chun; Jiang, Fan; Lang, Shao-ting; Xia, Min

    2014-01-01

    Highlights: • Tungsten coatings on graphite were firstly obtained by electro-deposition method via Na 2 WO 4 –WO 3 molten salt system. • Uniform and dense tungsten coatings could be easily prepared in each face of the sample, especially the complex components. • The obtained tungsten coatings are with high purity, ultra-low oxygen content (about 0.022 wt%). • Modulate pulse parameters can get tungsten coatings with different thickness and hardness. - Abstract: Tungsten coating on graphite substrate is one of the most promising candidate materials as the ITER plasma facing components. In this paper, tungsten coatings on graphite substrates were fabricated by electro-deposition from Na 2 WO 4 –WO 3 molten salt system at 1173 K in atmosphere. Tungsten coatings with no impurities were successfully deposited on graphite substrates under various pulsed current densities in an hour. By increasing the current density from 60 mA cm −2 to 120 mA cm −2 an increase of the average size of tungsten grains, the thickness and the hardness of tungsten coatings occurs. The average size of tungsten grains can reach 7.13 μm, the thickness of tungsten coating was in the range of 28.8–51 μm, and the hardness of coating was higher than 400 HV. No cracks or voids were observed between tungsten coating and graphite substrate. The oxygen content of tungsten coating is about 0.022 wt%

  9. Photoelectrochemical solar cells based on Bi{sub 2}WO{sub 6}; Celdas solares fotoelectroquimicas basadas en Bi{sub 2}WO{sub 6}

    Energy Technology Data Exchange (ETDEWEB)

    Madriz, Lorean; Tata, Jose; Cuartas, Veronica; Cuellar, Alejandra; Vargas, Ronald, E-mail: lmadriz@usb.ve [Departamento de Quimica, Universidad Simon Bolivar, Caracas (Venezuela, Bolivarian Republic of)

    2014-04-15

    In this study, photoelectrochemical solar cells based on bismuth tungstate electrodes were evaluated. Bi{sub 2}WO{sub 6} was synthesized by a hydrothermal method and characterized by scanning electron microscopy, UV-Vis reflectance spectroscopy, and X-ray powder diffraction. For comparison, solar cells based on TiO{sub 2} semiconductor electrodes were evaluated. Photoelectrochemical response of Grätzel-type solar cells based on these semiconductors and their corresponding sensitization with two inexpensive phthalocyanines dyes were determined. Bi{sub 2}WO{sub 6}-based solar cells presented higher values of photocurrent and efficiency than those obtained with TiO{sub 2} electrodes, even without sensitization. These results portray solar cells based on Bi{sub 2}WO{sub 6} as promising devices for solar energy conversion owing to lower cost of production and ease of acquisition. (author)

  10. MIS gas sensors based on porous silicon with Pd and WO{sub 3}/Pd electrodes

    Energy Technology Data Exchange (ETDEWEB)

    Solntsev, V.S. [Institute of Semiconductor Physics, National Academy of Science of Ukraine, 03028, Kiev (Ukraine); Gorbanyuk, T.I., E-mail: tatyanagor@mail.r [Institute of Semiconductor Physics, National Academy of Science of Ukraine, 03028, Kiev (Ukraine); Litovchenko, V.G.; Evtukh, A.A. [Institute of Semiconductor Physics, National Academy of Science of Ukraine, 03028, Kiev (Ukraine)

    2009-09-30

    Pd and WO{sub 3}/Pd gate metal-oxide-semiconductor (MIS) gas sensitive structures based on porous silicon layers are studied by the high frequency C(V) method. The chemical compositions of composite WO{sub 3}/Pd electrodes are characterized by secondary-ion mass spectrometry (SIMS). The atomic force microscopy (AFM) was used for morphologic studies of WO{sub 3}/Pd films. As shown in the experiments, WO{sub 3}/Pd structures are more sensitive and selective to the adsorption of hydrogen sulphide compared to Pd gate. The analyses of kinetic characteristics allow us to determine the response and characteristic times for these structures. The response time of MIS-structures with thin composite WO{sub 3}/Pd electrodes (the thickness of Pd is about 50 nm with WO{sub 3} clusters on its surface) is slower compared to the structures with Pd electrodes. Slower sensor responses of WO{sub 3}-based gas sensors may be associated with different mechanism of gas sensitivity of given structures. The enhanced sensitivity and selectivity to H{sub 2}S action of WO{sub 3}/Pd MIS-structures can also be explained by the chemical reaction that occurs at the catalytic active surface of gate electrodes. The possible mechanisms of enhanced sensitivity and selectivity to H{sub 2}S adsorption of MIS gas sensors with WO{sub 3}/Pd composite gate electrodes compared to pure Pd have been analyzed.

  11. Tungsten oxide-graphene oxide (WO3-GO) nanocomposite as an efficient photocatalyst, antibacterial and anticancer agent

    Science.gov (United States)

    Jeevitha, G.; Abhinayaa, R.; Mangalaraj, D.; Ponpandian, N.

    2018-05-01

    Functioning of ultrasonically prepared tungsten oxide-graphene oxide (WO3-GO) nanocomposite as a photocatalyst, antibacterial and anticancer system was investigated and the obtained results were compared with that of pure WO3 nanoparticles. Structural, morphological, compositional and optical properties of the prepared WO3 nanoparticles and WO3-GO nanocomposite were studied. Photocatalytic efficiency of the system on organic dyes such as methylene blue (MB, cationic) and indigo carmine (IC, anionic) was investigated. The enhanced efficiency of the WO3-GO nanocomposite system was evaluated under sunlight and compared with that of pure WO3. The degradation efficiency values for MB and IC were found to be 97.03% and 95.43% at 180 and 120 min respectively. Antibacterial activity of the WO3-GO nanocomposite under visible light was tested and improved inhibition results were observed for Escherichia coli and Bacillus subtilis after 6 h of light exposure. The photocatalytic degradation efficiency and antibacterial activity of the WO3-GO nanocomposite are attributed to the improved electron-hole pair separation rate. Investigation on anticancer activity of WO3-GO nanocomposite was tested on human lung cancer (A-549) cell line and the IC50 value was found to be 139.6 ± 4.53 μg/mL. The results obtained in this study may be used as a platform for the development of photocatalysis applications based on WO3-GO nanocomposite.

  12. Experimental and theoretical investigation on photocatalytic activities of 1D Ag/Ag2WO4 nanostructures

    Science.gov (United States)

    Liu, Danqing; Huang, Weicheng; Li, Long; Liu, Lu; Sun, Xiaojun; Liu, Bo; Yang, Bin; Guo, Chongshen

    2017-09-01

    Ag2WO4 is a significant photocatalyst that responds to UV light irradiation only, which greatly hinders it for further practical application for solar light. To address this problem, herein, 1D plasmonic Ag/Ag2WO4 photocatalysts have been fabricated by a successive process including hydrothermal synthesis to obtain Ag2WO4 followed by an additional in situ chemical-reduction process for Ag decoration. Then, the structural features, optical properties, and electronic structures of Ag2WO4 and Ag/Ag2WO4 nanowires were systematically investigated via a combination of theoretical calculations and experimental evidence. The plasmon-enhanced Ag/Ag2WO4 nanowires exhibited higher visible-light-driven photocatalytic activity, which performed a desired photodestruction ratio of 91.2% on methylene blue within 60 min and good stability in five cycles. The Ag decoration greatly facilitates visible-light harvesting and thus promotes photogenerated radical oxidation to dye, which is evidenced by the higher hydroxyl radical level of Ag/Ag2WO4 detected in the ESR test during the photocatalytic process. The theoretical calculation based on density functional theory indicates that Ag nanoparticles formed on the surface of Ag2WO4 could narrow the band gap of Ag2WO4. In addition, the surface plasmon resonance absorption effect and fast charge transfer effect in the metal-semiconductor system contribute to the photocatalytic performance of Ag/Ag2WO4.

  13. Study of the tungsten bronze Ag0.01WO3 using positron annihilation method

    International Nuclear Information System (INIS)

    Dryzek, J.; Dryzek, E.; Placzek, A.

    1992-01-01

    The study of the positron annihilation and the Seebeck effect was performed on silver doped tungsten trioxide of composition Ag 0.01 WO 3 and the tungsten trioxide phase: WO 2.90 (W 20 O 58 ). Both methods point out that there are some clusters of Ag + ions in the first compound and oxygen vacancies in the second case. The clusters have some internal substructure. The measurements of the Seebeck effect showed that Ag 0.01 WO 3 is normal n-type semiconductor whereas WO 2.90 exhibits metal-like properties

  14. Tungsten oxides. I. Effects of oxygen vacancies and doping on electronic and optical properties of different phases of WO3

    Science.gov (United States)

    Migas, D. B.; Shaposhnikov, V. L.; Rodin, V. N.; Borisenko, V. E.

    2010-11-01

    In this part we present results of our ab initio calculations indicating that dispersion of the bands near the gap region for different phases of WO3 (namely, ɛ-WO3, δ-WO3, γ-WO3, β-WO3, orth-WO3, α-WO3, and hex-WO3) is rather close. The rapid increase in the absorption coefficient starts at the lower energy range for α-WO3 and hex-WO3 than for the other phases in accordance with the calculated band gaps. An oxygen vacancy has turned out to decrease the gap by 0.50 eV and to shift the absorption coefficient to the lower energy range in the room temperature γ-WO3 phase. We have also traced changes caused by molybdenum and sulfur doping of γ-WO3. Only sulfur doped γ-WO3 has been revealed to display the formation of the impurity band along with a sizable reduction in the gap and the shift in the absorption coefficient to the lower energy range.

  15. Facile Hydrogen Evolution Reaction on WO3Nanorods

    Directory of Open Access Journals (Sweden)

    Rajeswari Janarthanan

    2007-01-01

    Full Text Available AbstractTungsten trioxide nanorods have been generated by the thermal decomposition (450 °C of tetrabutylammonium decatungstate. The synthesized tungsten trioxide (WO3 nanorods have been characterized by XRD, Raman, SEM, TEM, HRTEM and cyclic voltammetry. High resolution transmission electron microscopy and X-ray diffraction analysis showed that the synthesized WO3nanorods are crystalline in nature with monoclinic structure. The electrochemical experiments showed that they constitute a better electrocatalytic system for hydrogen evolution reaction in acid medium compared to their bulk counterpart.

  16. Synthesis, characterization and liquefied petroleum gas (LPG) sensing properties of WO3 nano-particles

    Science.gov (United States)

    Singh, Subhash; Majumder, S. B.

    2018-05-01

    Metal oxide sensors, such as ZnO, SnO2, and WO3 etc. have been utilized for several decades for low-costd etection of combustible and toxic gases. In the present work tungsten oxide (WO3) nanoparticles have been prepared by using an economic wet chemical synthesis route. To understand the phase formation behavior of the synthesized powders, X-ray diffraction analysis has been performed. The microstructure evolution of the synthesized powders was characterized by field-emission scanning electron microscopy (FESEM), and transmission electron microscopy (TEM). The calcined phase pure WO3 nanoparticles are investigated in terms of LPG gas sensing properties. The gas sensing measurements has been done in two different mode of operation (namely static and dynamic measurements). The degree of oxygen deficiency in the WO3 sensor also affected the sensor properties and the optimum oxygen content of WO3 was necessary to get high sensitivity for LPG. The WO3 sensor shows the excellent sensor properties for LPG at the operating temperature of 250°C.

  17. Subsolidus Phase Relations of the CaO-WO3-CuO System at 800 °C in Air

    DEFF Research Database (Denmark)

    Grivel, J. -C.

    2012-01-01

    The subsolidus phase relations of the CaO-WO3-CuO system were investigated in air. The samples were equilibrated at 800 degrees C. Under these conditions, five binary oxide phases are stable: Ca2CuO3, Cu3WO6, CuWO4, CaWO4 and Ca3WO6. The pseudo-ternary section is characterised by 6 three...

  18. Secondary recrystallisation in 20 w/o Cr-25 w/o Ni-Nb stabilised stainless steel

    International Nuclear Information System (INIS)

    Healey, T.; Brown, A.F.; Speight, M.V.

    1976-11-01

    The fuel cladding material for the Commercial Advanced Gas Reactor is a fine grain 20 w/o Cr-25 w/o Ni niobium stabilised stainless steel. The grain structure stability of this alloy has been investigated as a function of carbon content over the temperature range 930 - 990 0 C. It is demonstrated that the primary grain structure is susceptible to abnormal growth due to secondary recrystallisation of the initial fine grain structure after a composition and temperature dependent incubation period. The magnitude of the incubation period is analysed on the basis that secondary recrystallisation commences when randomly dispersed niobium carbide particles have coarsened to a critical size. The validity of the analysis is tested by comparing the predictions with experimental observation. The model is subsequently used to evaluate the incubation period for conditions of temperature, composition and microstructure which differ from those defined in the experimental studies. (author)

  19. Pt supported self-assembled nest-like-porous WO3 hierarchical microspheres as electrocatalyst for methanol oxidation

    International Nuclear Information System (INIS)

    Zhang, Jun; Tu, Jiang-ping; Du, Gao-hui; Dong, Zi-min; Su, Qing-mei; Xie, Dong; Wang, Xiu-li

    2013-01-01

    Highlights: ► Nest-like-porous (NLP) WO 3 microspheres are assembled by a hydrothermal method. ► The NLP-WO 3 microspheres have a hexagonal structure and high porous surface. ► Great enhancement of electrochemical property is achieved for Pt/NLP-WO 3 microspheres. -- Abstract: Hexagonal tungsten trioxide (hex-WO 3 ) hierarchical microspheres with nest-like pores are synthesized by a facile hydrothermal method. The nest-like-porous (NLP) WO 3 hierarchical microspheres with 5–6 μm in diameters are self-assembled of single-crystal nanowires. The nanowires have lengths of several hundred nanometers and diameters of 5–30 nm; the long axis of nanowire is oriented toward 〈0 0 1〉 direction. The specific surface area of hex-WO 3 microspheres is 62 m 2 g −1 . 20 wt.% Pt nanoparticles with ∼7 nm are loaded onto the WO 3 microspheres using a conventional microwave-assisted ethylene glycol (EG) method. The electrocatalytic activity for methanol oxidation of Pt/NLP-WO 3 microspheres is investigated by cyclic voltammetry and chronoamperometry. Due to the large tunnels of hexagonal structure and high porous surface morphology, great enhancement of electrochemical performance is achieved. The Pt/NLP-WO 3 microspheres are demonstrated to be a promising anode material for direct methanol fuel cells (DMFC)

  20. Physical properties characterization of WO{sub 3} films grown by hot-filament metal oxide deposition

    Energy Technology Data Exchange (ETDEWEB)

    Diaz-Reyes, J., E-mail: jdiazr2001@yahoo.com [Centro de Investigacion en Biotecnologia Aplicada del Instituto Politecnico Nacional, Ex-Hacienda de San Juan Molino, Km. 1.5, Tepetitla, Tlaxcala, 90700 (Mexico); Delgado-Macuil, R.J. [Centro de Investigacion en Biotecnologia Aplicada del Instituto Politecnico Nacional, Ex-Hacienda de San Juan Molino, Km. 1.5, Tepetitla, Tlaxcala, 90700 (Mexico); Dorantes-Garcia, V. [Preparatoria ' Simon Bolivar' de la Benemerita Universidad Autonoma de Puebla, 4 Oriente 408, Col. Centro, Atlixco, Puebla, C. P. 74200 (Mexico); Perez-Benitez, A. [Facultad de Ciencias Quimicas de la Benemerita Universidad Autonoma Puebla, 14 Sur y Av. San Claudio, Col. San Manuel, Puebla, Puebla, C. P. 72570 (Mexico); Balderas-Lopez, J.A. [Unidad Profesional Interdisciplinaria de Biotecnologia del Instituto Politecnico Nacional, Avenida Acueducto S/N, Col. Barrio la Laguna, Ticoman, Del. Gustavo A. Madero, Mexico, D.F. 07340 (Mexico); Ariza-Ortega, J.A. [Centro de Investigacion en Biotecnologia Aplicada del Instituto Politecnico Nacional, Ex-Hacienda de San Juan Molino, Km. 1.5, Tepetitla, Tlaxcala, 90700 (Mexico)

    2010-10-25

    WO{sub 3} is grown by hot-filament metal oxide deposition (HFMOD) technique under atmospheric pressure and an oxygen atmosphere. By X-ray diffraction obtains that WO{sub 3} presents mainly monoclinic crystalline phase. The chemical stoichiometry is obtained by X-ray Photoelectron Spectroscopy (XPS). The IR spectrum of the as-grown WO{sub 3} presents broad peaks in the range of 1100 to 3600 cm{sup -1}. A broad band in the 2200 to 3600 cm{sup -1} region and the peaks sited at 1645 and 1432 cm{sup -1} are well resolved, which are originated from moisture and are assigned to {nu}(OH) and {delta}(OH) modes of adsorbed water and the corresponding tungsten oxide vibrations are in infrared region from 400 to 1453 cm{sup -1} and around 3492 cm{sup -1}, which correspond to tungsten-oxygen (W-O) stretching, bending and lattice modes. The Raman spectrum shows intense peaks at 801, 710, 262 and 61 cm{sup -1} that are typical Raman peaks of crystalline WO{sub 3} (m-phase) that correspond to stretching vibrations of the bridging oxygen, which are assigned to W-O stretching ({nu}) and W-O bending ({delta}) modes, respectively. By transmittance measurements obtains that the WO{sub 3} band gap can be varied from 2.92 to 3.13 eV in the investigated annealing temperature range.

  1. WO3 nanoflakes decorated with CuO clusters for enhanced photoelectrochemical water splitting

    Directory of Open Access Journals (Sweden)

    Chongwu Wang

    2018-04-01

    Full Text Available The low quantum efficiency arising from poor charges transfer and insufficient light absorption is one of the critical challenges toward achieving highly efficient water splitting in photoelectrochemical cells. Three dimensions (3D structures and heterojunctions have received intensive research interests recent years due to their excellent ability to separate photo-generated charges as well as the enhanced light harvesting property. Herein, 3D CuO/WO3 structure was fabricated through a facile solvothermal method followed by chemical bath deposition. The loading of CuO clusters on WO3 nanoflake arrays results in a much improved photocurrent density compared with that of pristine WO3 nanoflake arrays, which reaches 1.8 mA/cm2 at 1.23 V vs. the reversible hydrogen electrode. The electrochemical impedance spectroscopy measurement demonstrates that the improved performance of CuO/WO3 electrode is attributed to the accelerated charge transfer kinetics as a result of the desirable band alignment in CuO/WO3 heterojunction. This work demonstrates a facile strategy to construct superior WO3 electrode, which will ultimately allow for efficient storage of solar energy into hydrogen. Keywords: Photoelectrochemistry, Water splitting, Tungsten trioxide photoanode, CuO clusters, Heterojunction

  2. Neuromorphic transistor achieved by redox reaction of WO3 thin film

    Science.gov (United States)

    Tsuchiya, Takashi; Jayabalan, Manikandan; Kawamura, Kinya; Takayanagi, Makoto; Higuchi, Tohru; Jayavel, Ramasamy; Terabe, Kazuya

    2018-04-01

    An all-solid-state neuromorphic transistor composed of a WO3 thin film and a proton-conducting electrolyte was fabricated for application to next-generation information and communication technology including artificial neural networks. The drain current exhibited a 4-order-of-magnitude increment by redox reaction of the WO3 thin film owing to proton migration. Learning and forgetting characteristics were well tuned by the gate control of WO3 redox reactions owing to the separation of the current reading path and pulse application path in the transistor structure. This technique should lead to the development of versatile and low-power-consumption neuromorphic devices.

  3. Characterisation and application of WO3 films for electrochromic devices

    Science.gov (United States)

    Stapinski, Thomas; Marszalek, Konstanty; Swatowska, Barbara; Stanco, Agnieszka

    2013-07-01

    Electrochromic system is the one of the most popular devices using color memory effect under the influence of an applied voltage. The electrochromic system was produced based on the thin WO3 electrochromic films. Films were prepared by RF magnetron sputtering from tungsten targets in a reactive Ar+O2 gas atmosphere of various Ar/O2 ratios. The technological gas mixture pressure was 3 Pa and process temperature 30°C. Structural and optical properties of WO3 films were investigated for as-deposited and heat treated samples at temperature range from 350°C to 450°C in air. The material revealed the dependence of properties on preparation conditions and on post-deposition heat treatment. Main parameters of thin WO3 films: thickness d, refractive index n, extinction coefficient k and energy gap Eg were determined and optimized for application in electrochromic system. The main components of the system were glass plate with transparent conducting oxides, electrolyte, and glass plate with transparent conducting oxides and WO3 layer. The optical properties of the system were investigated when a voltage was applied across it. The electrochromic cell revealed the controllable transmittance depended on the operation voltage.

  4. Preparation of three dimensional graphene foam–WO3 nanocomposite with enhanced visible light photocatalytic activity

    International Nuclear Information System (INIS)

    Azimirad, R.; Safa, S.

    2015-01-01

    Three dimensional graphene foam (3D GF) was synthesized by chemical vapor deposition (CVD) on a nickel foam skeleton. After dissolving the nickel foam, the obtaining 3D GF was used as a highly porous conductive substrate for nucleation and growth of WO 3 particles. Scanning electron microscopy (SEM) and Raman spectroscopy was employed to ensure the quality of the prepared GFs and to judge about the 3D GF–WO 3 chemical structure. The WO 3 characteristic Raman peaks centered at 726, and 809 cm −1 are slightly broadened and displaced to lower wavelength in the 3D GF–WO 3 nanocomposite, as compared to the corresponding peaks of the bare tungsten oxide. This phenomenon confirms the formation of W–C and W–O–C bonds in composite material which is important for faster transferring the photoexcited electrons to graphene 3D network as an exceptional electron acceptor. The 3D GF−WO 3 composite material was applied in photocatalytic degradation of Rhodamine B dye. It was observed that the annealed samples show an excellent photocatalytic performance relative to the as-prepared 3D GF−WO 3 samples and bare WO 3 , which is ascribed to the lower electron/hole recombination through the formation of W–C and W–O–C bonds. - Highlights: • 3D GF synthesized by CVD on a nickel foam as a highly porous conductive substrate. • WO 3 nanoparticles coated on 3D GF by dip-coating. • 3D GF−WO 3 shows an excellent photocatalytic degradation of Rhodamine B dye. • Better photocatalytic properties assigned to the formation of W–C and W–O–C bonds

  5. Preparation of ultra-thin and high-quality WO{sub 3} compact layers and comparision of WO{sub 3} and TiO{sub 2} compact layer thickness in planar perovskite solar cells

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Jincheng; Shi, Chengwu, E-mail: shicw506@foxmail.com; Chen, Junjun; Wang, Yanqing; Li, Mingqian

    2016-06-15

    In this paper, the ultra-thin and high-quality WO{sub 3} compact layers were successfully prepared by spin-coating-pyrolysis method using the tungsten isopropoxide solution in isopropanol. The influence of WO{sub 3} and TiO{sub 2} compact layer thickness on the photovoltaic performance of planar perovskite solar cells was systematically compared, and the interface charge transfer and recombination in planar perovskite solar cells with TiO{sub 2} compact layer was analyzed by electrochemical impedance spectroscopy. The results revealed that the optimum thickness of WO{sub 3} and TiO{sub 2} compact layer was 15 nm and 60 nm. The planar perovskite solar cell with 15 nm WO{sub 3} compact layer gave a 9.69% average and 10.14% maximum photoelectric conversion efficiency, whereas the planar perovskite solar cell with 60 nm TiO{sub 2} compact layer achieved a 11.79% average and 12.64% maximum photoelectric conversion efficiency. - Graphical abstract: The planar perovskite solar cell with 15 nm WO{sub 3} compact layer gave a 9.69% average and 10.14% maximum photoelectric conversion efficiency, whereas the planar perovskite solar cell with 60 nm TiO{sub 2} compact layer achieved a 11.79% average and 12.64% maximum photoelectric conversion efficiency. Display Omitted - Highlights: • Preparation of ultra-thin and high-quality WO{sub 3} compact layers. • Perovskite solar cell with 15 nm-thick WO{sub 3} compact layer achieved PCE of 10.14%. • Perovskite solar cell with 60 nm-thick TiO{sub 2} compact layer achieved PCE of 12.64%.

  6. Oxygen partial pressure effects on the magnetron sputtered WO3 films

    International Nuclear Information System (INIS)

    Muğlu, G Merhan; Gür, E

    2016-01-01

    Electrochromism is changing color of a substance in response to the applied an external electric field and the phenomenon is reversible. WO 3 is very attractive material due to its electrochromic properties as well as it is also attractive for many different applications such as gas sensors, phosphorous screen, textile, glass industry. In this study, it is aimed to provide optimization of the optical and structural characteristics of WO 3 by changing the growth parameters mainly the oxygen partial pressure. The partial pressure of oxygen was changed with increments of 0.7 mTorr. For the analysis, X-ray Diffraction (XRD), absorption, Raman spectroscopy measurements were used. When O 2 gas increased, peaks belong to the WO 3 was observed in XRD patterns at the 2 theta angles of 23.0, 11.0, 23.5 and 28.5 angles corresponding to the (002), (020) and (220) planes, respectively. This shows that there is a significant effect of increasing O 2 partial pressure in the formation of WO 3 films. The bandgap energy of the WO 3 thin films are found to be around 3.0 eV. Raman measurements showed vibrational modes of W-O-W stretching and bending modes which shows small shifts depending on the partial pressures of the O 2 . Obtained results indicated that better crystal structure is obtained with higher O 2 gas partial pressure. (paper)

  7. Liquid phase deposition of WO3/TiO2 heterojunction films with high photoelectrocatalytic activity under visible light irradiation

    International Nuclear Information System (INIS)

    Zhang, Man; Yang, Changzhu; Pu, Wenhong; Tan, Yuanbin; Yang, Kun; Zhang, Jingdong

    2014-01-01

    Highlights: • Liquid phase deposition is developed for preparing WO 3 /TiO 2 heterojunction films. • TiO 2 film provides an excellent platform for WO 3 deposition. • WO 3 expands the absorption band edge of TiO 2 film to visible light region. • WO 3 /TiO 2 heterojunction film shows high photoelectrocatalytic activity. - ABSTRACT: The heterojunction films of WO 3 /TiO 2 were prepared by liquid phase deposition (LPD) method via two-step processes. The scanning electron microscopy, X-ray diffraction and X-ray photoelectron spectroscopic analysis indicated that flower-like WO 3 film was successfully deposited on TiO 2 film with the LPD processes. The TiO 2 film provided an excellent platform for WO 3 deposition while WO 3 obviously expanded the absorption of TiO 2 film to visible light. As the result, the heterojunction film of WO 3 /TiO 2 exhibited higher photocurrent response to visible light illumination than pure TiO 2 or WO 3 film. The photoelectrocatalytic (PEC) activity of WO 3 /TiO 2 film was evaluated by degrading Rhodamin B (RhB) and 4-chlorophenol (4-CP) under visible light irradiation. The results showed that the LPD WO 3 /TiO 2 film possessed high PEC activity for efficient removal of various refractory organic pollutants

  8. Study of photocatalytic activities of Bi2WO6 nanoparticles synthesized by fast microwave-assisted method

    International Nuclear Information System (INIS)

    Phu, Nguyen Dang; Hoang, Luc Huy; Chen, Xiang-Bai; Kong, Meng-Hong; Wen, Hua-Chiang; Chou, Wu Ching

    2015-01-01

    We present a study of photocatalytic activities of Bi 2 WO 6 nanoparticles synthesized by fast microwave-assisted method. The photocatalytic activities of the nanoparticles were evaluated by the decolorization of methylene-blue under visible-light-irradiation. Our results show that the surface area of Bi 2 WO 6 nanoparticles plays a major role for improving photocatalytic activity, while visible-light absorption has only a weak effect on photocatalytic activity. This suggests efficient transportation of photo-generated electrons and holes to the oxidation active sites on the surface of nanoparticles, indicating Bi 2 WO 6 nanoparticles synthesized by fast microwave-assisted method are promising for achieving high photocatalytic activity under visible-light-irradiation. - Highlights: • The Bi 2 WO 6 nanoparticles were synthesized via fast microwave-assisted method. • The obtained Bi 2 WO 6 nanoparticles exhibited visible-light absorbance. • The surface area of Bi 2 WO 6 nanoparticles plays major role for improving photocatalytic activity. • The Bi 2 WO 6 nanoparticles are promising for achieving high photocatalytic activity under visible-light-irradiation

  9. Degradation of malachite green on Pd/WO3 photocatalysts under simulated solar light

    International Nuclear Information System (INIS)

    Liu Yonggang; Ohko, Yoshihisa; Zhang Ruiqin; YangYingnan; Zhang Zhenya

    2010-01-01

    The photocatalytic degradation of malachite green (MG) dye molecules in aqueous solution was investigated by using palladium (Pd) modified tungsten trioxide (WO 3 ) under simulated solar light. The optimum values for Pd content vs. WO 3 and catalyst concentration in solution for MG (5.0 μmol L -1 ) degradation were 0.5 wt.% and 150 mg L -1 , respectively. The MG concentration change followed the pseudo first order kinetics of the Langmuir-Hinshelwood model. Since MG was also degraded under visible light (λ > 470 nm), which was not absorbed by WO 3 , the mechanism involved both the photocatalytic degradation and self-sensitized degradation of MG. Pd modified WO 3 would be useful as an efficient tool for the decolorization of wastewater under solar light.

  10. Reduced graphene oxide/δ-WO{sub 3} composites for volatile organic compounds sensing

    Energy Technology Data Exchange (ETDEWEB)

    Perfecto, Tarcisio Micheli; Zito, Cecilia de Almeida; Volanti, Diogo Paschoalini, E-mail: tarcisio93@hotmail.com [Universidade Estadual Paulista Julio de Mesquita Filho (UNESP), Sao Paulo, SP (Brazil)

    2016-07-01

    Full text: Metal oxide semiconductors (MOS) is a simple and low-cost alternative to detect volatile organic compounds (VOCs) with fast response and recovery time [1]. In this context, reduced graphene oxide (RGO) is used in order to achieve a superior metal oxides gas sensing performance [2]. Thus, we report the synthesis of RGO/δ-WO{sub 3} composites by microwave-assisted hydrothermal method and its application in VOCs detection. The composites were prepared in a single-step using a graphene oxide dispersion, tungsten salt, ammonium oxalate hydrate as morphological control agent, and HCl in aqueous medium. The mixture was sealed in an autoclave and irradiated by microwave (800W) at 140 °C for 10 minutes. Then the sample was heating treatment at 400 °C for 1 hour. δ-WO{sub 3} single phase was also prepared by the same process without graphene oxide. The XRD results indicated the successful formation of triclinic phase of WO{sub 3} for both samples. FEG-SEM images showed the δ-WO{sub 3} nanoplates formation that are agglomerated and become more disperse and with irregular shape in RGO/δ-WO{sub 3} composite. TEM analysis revealed the interaction between RGO and δ-WO{sub 3} particles. The preliminary gas sensing results showed that increasing the operation temperature, more sensitive the composite RGO/δ-WO{sub 3} was toward the ethanol, methanol, acetone, toluene and benzene. So far, the highest response observed was to acetone at 300 °C. The response of RGO/δ-WO{sub 3} to 5, 10, 50, 100 and 200 ppm of acetone was 1.08, 1.12, 1.42, 1.75, and 1.99, respectively. We expect that increasing the operating temperature, more sensitive the material will become, since reports shows that WO{sub 3} sensors exhibit higher responses at higher temperatures [3]. Acknowledgments: The authors acknowledge FAPESP grants: 16/04371-1, 15/04306-2 and 14/17343-0. Refs.: [1] Jiang, D.;et al. RSC Adv. 2015, 5 (49), 39442-39448. [2] Jie, X.; et al. Sensors Actuators B Chem. 2015, 220

  11. Conductive surface modification of cauliflower-like WO{sub 3} and its electrochemical properties for lithium-ion batteries

    Energy Technology Data Exchange (ETDEWEB)

    Yoon, Sukeun, E-mail: skyoon@kongju.ac.kr [Division of Advanced Materials Engineering, Kongju National University, Chungnam 330-717 (Korea, Republic of); Woo, Sang-Gil [Advanced Batteries Research Center, Korea Electronics Technology Institute, Gyeonggi 463-816 (Korea, Republic of); Jung, Kyu-Nam [Energy Efficiency and Materials Research Division, Korea Institute of Energy Research, Daejeon 305-343 (Korea, Republic of); Song, Huesup, E-mail: hssong@kongju.ac.kr [Division of Advanced Materials Engineering, Kongju National University, Chungnam 330-717 (Korea, Republic of)

    2014-11-15

    Highlights: • Synthesis of cauliflower-like carbon-decorated WO{sub 3}. • Superior cyclability and rate capability for cauliflower-like carbon-decorated WO{sub 3}. • Electrochemical reaction behavior of cauliflower-like carbon-decorated WO{sub 3} with lithium. • In-situ XRD analysis during the first discharge–charge shows a complex reaction of intercalation and conversion of WO{sub 3}. - Abstract: Cauliflower-like WO{sub 3} was synthesized by a hydrothermal reaction without a surfactant, followed by firing, and was investigated as an anode material for lithium-ion battery applications. The scanning electron microscope (SEM) and transmission electron microscope (TEM) characterization indicated that WO{sub 3} nanorods had an aggregation framework and built a cauliflower morphology. With the objective of understanding the charge–discharge process within a voltage range of 0–3 V vs. Li{sup +}/Li, in situ X-ray diffraction was used and a complex reaction of intercalation and conversion of WO{sub 3} was revealed for the first time. The cauliflower-like WO{sub 3} after being decorated with carbon provides a high gravimetric capacity of >635 mA h/g (Li{sub 5.5}WO{sub 3}) with good cycling and a high rate capability when used as an anode in lithium-ion batteries. Based on our studies, we attribute the high electrochemical performance to the nanoscopic WO{sub 3} particles and a conductive carbon layer, which makes them a potential candidate for lithium-ion batteries.

  12. Historic Concrete : From Concrete Repair to Concrete Conservation

    NARCIS (Netherlands)

    Heinemann, H.A.

    2013-01-01

    Concrete like materials were already applied during the Roman Empire. After the decline of the Roman Empire, a wide scale application of concrete only reappeared in the 19th century. Here lies also the origin of modern (reinforced) concrete. Since then, both concrete application and composition have

  13. Ag loaded WO_3 nanoplates for efficient photocatalytic degradation of sulfanilamide and their bactericidal effect under visible light irradiation

    International Nuclear Information System (INIS)

    Zhu, Wenyu; Liu, Jincheng; Yu, Shuyan; Zhou, Yan; Yan, Xiaoli

    2016-01-01

    Highlights: • WO_3/Ag heterogeneous composites were fabricated with simply photo-reduction method. • Property changes due to Ag loading were systematically studied. • WO_3/Ag composites efficiently degraded sulfanilamide under visible light irradiation. • WO_3/Ag composites exhibited bactericidal effectS under visible light irradiation. - Abstract: Sulfonamides (SAs) are extensively used antibiotics and their residues in the water bodies propose potential threat to the public. In this study, degradation efficiency of sulfanilamide (SAM), which is the precursor of SAs, using WO_3 nanoplates and their Ag heterogeneous as photocatalysts was investigated. WO_3 nanoplates with uniform size were synthesized by a facile one step hydrothermal method. Different amount of Ag nanoparticles (Ag NPs) were loaded onto WO_3 nanoplates using a photo-reduction method to generate WO_3/Ag composites. The physio-chemical properties of synthesized nanomaterials were systematically characterized. Photodegradation of SAM by WO_3 and WO_3/Ag composites was conducted under visible light irradiation. The results show that WO_3/Ag composites performed much better than pure WO_3 where the highest removal rate was 96.2% in 5 h. Ag as excellent antibacterial agent also endows certain antibacterial efficiency to WO_3, and 100% removal efficiency against Escherichia Coli and Bacillus subtilis could be achieved in 2 h under visible light irradiation for all three WO_3/Ag composites synthesized. The improved performance in terms of SAM degradation and antibacterial activity of WO_3/Ag can be attributed to the improved electron-hole pair separation rate where Ag NPs act as effective electron trapper during the photocatalytic process.

  14. Light-Driven Au-WO3@C Janus Micromotors for Rapid Photodegradation of Dye Pollutants.

    Science.gov (United States)

    Zhang, Qilu; Dong, Renfeng; Wu, Yefei; Gao, Wei; He, Zihan; Ren, Biye

    2017-02-08

    A novel light-driven Au-WO 3 @C Janus micromotor based on colloidal carbon WO 3 nanoparticle composite spheres (WO 3 @C) prepared by one-step hydrothermal treatment is described. The Janus micromotors can move in aqueous media at a speed of 16 μm/s under 40 mW/cm 2 UV light due to diffusiophoretic effects. The propulsion of such Au-WO 3 @C Janus micromotors (diameter ∼ 1.0 μm) can be generated by UV light in pure water without any external chemical fuels and readily modulated by light intensity. After depositing a paramagnetic Ni layer between the Au layer and WO 3 , the motion direction of the micromotor can be precisely controlled by an external magnetic field. Such magnetic micromotors not only facilitate recycling of motors but also promise more possibility of practical applications in the future. Moreover, the Au-WO 3 @C Janus micromotors show high sensitivity toward extremely low concentrations of sodium-2,6-dichloroindophenol (DCIP) and Rhodamine B (RhB). The moving speed of motors can be significantly accelerated to 26 and 29 μm/s in 5 × 10 -4 wt % DCIP and 5 × 10 -7 wt % RhB aqueous solutions, respectively, due to the enhanced diffusiophoretic effect, which results from the rapid photocatalytic degradation of DCIP and RhB by WO 3 . This photocatalytic acceleration of the Au-WO 3 @C Janus micromotors confirms the self-diffusiophoretic mechanism and opens an opportunity to tune the motility of the motors. This work also offers the light-driven micromotors a considerable potential for detection and rapid photodegradation of dye pollutants in water.

  15. Solid-State Electrochromic Device Consisting of Amorphous WO3 and Various Thin Oxide Layers

    Science.gov (United States)

    Shizukuishi, Makoto; Shimizu, Isamu; Inoue, Eiichi

    1980-11-01

    A mixed oxide containing Cr2O3 was introduced into an amorphous WO3 solid-state electrochromic device (ECD) in order to improve its colour memory effect. The electrochromic characteristics were greatly affected by the chemical constituents of a dielectric layer on the a-WO3 layer. Particularly, long memory effect and low power dissipation were attained in a solid-state ECD consisting of a-WO3 and Cr2O3\\cdotV2O5(50 wt.%). Some electrochromic characteristics of the a-WO3/Cr2O3\\cdotV2O5 ECD and the role of V2O5 were investigated.

  16. Structural properties of WO{sub 3} dependent of the annealing temperature deposited by hot-filament metal oxide deposition

    Energy Technology Data Exchange (ETDEWEB)

    Flores M, J. E. [Benemerita Universidad Autonoma de Puebla, Facultad de Ciencias de la Electronica, Av. San Claudio y 18 Sur, Ciudad Universitaria, Col. Jardines de San Manuel, 72570 Puebla (Mexico); Diaz R, J. [IPN, Centro de Investigacion en Biotecnologia Aplicada, Ex-Hacienda de San Molino Km 1.5 Tepetitla, 90700 Tlaxcala (Mexico); Balderas L, J. A., E-mail: eflores@ece.buap.mx [IPN, Unidad Profesional Interdisciplinaria de Biotecnologia, Av. Acueducto s/n, Col. Barrio la Laguna, 07340 Mexico D. F. (Mexico)

    2012-07-01

    In this work presents a study of the effect of the annealing temperature on structural and optical properties of WO{sub 3} that has been grown by hot-filament metal oxide deposition. The chemical stoichiometry was determined by X-ray photoelectron spectroscopy. By X-ray diffraction obtained that the as-deposited WO{sub 3} films present mainly monoclinic crystalline phase. WO{sub 3} optical band gap energy can be varied from 2.92 to 3.15 eV obtained by transmittance measurements by annealing WO{sub 3} from 100 to 500 C. The Raman spectrum of the as-deposited WO{sub 3} film shows four intense peaks that are typical Raman peaks of crystalline WO{sub 3} (m-phase) that corresponds to the stretching vibrations of the bridging oxygen that are assigned to W-O stretching ({upsilon}) and W-O bending ({delta}) modes, respectively, which enhanced and increased their intensity with the annealing temperature. (Author)

  17. Comparative studies of monoclinic and orthorhombic WO3 films used for hydrogen sensor fabrication on SiC crystal

    International Nuclear Information System (INIS)

    Zuev, V V; Romanov, R I; Fominski, V Y; Grigoriev, S N; Volosova, M A; Demin, M V

    2016-01-01

    Amorphous WO x films were prepared on the SiC crystal by using two different methods, namely, reactive pulsed laser deposition (RPLD) and reactive deposition by ion sputtering (RDIS). After deposition, the WO x films were annealed in an air. The RISD film possessed a m-WO 3 structure and consisted of closely packed microcrystals. Localized swelling of the films and micro-hills growth did not destroy dense crystal packing. RPLD film had layered β-WO 3 structure with relatively smooth surface. Smoothness of the films were destroyed by localized swelling and the micro-openings formation was observed. Comparative study of m-WO 3 /SiC, Pt/m-WO 3 /SiC, and P-WO 3 /SiC samples shows that structural characteristics of the WO 3 films strongly influence on the voltage/current response as well as on the rate of current growth during H 2 detection at elevated temperatures. (paper)

  18. Study on the selection of steel or prestressed concrete cable stayed bridge by using diaggregate behavioral model; Hishukei rojitto model wo mochiita koshachokyo to PC shachokyo no kyoshiki sentaku ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Araki, Y.; Furuta, H.; Maeda, E.; Furukawa, K. [Yamaguchi University, Yamaguchi (Japan). Faculty of Engineering

    1994-09-15

    A discussion was given to make clear the selection factors in selecting bridge types (steel cable stayed bridge and prestressed concrete cable stayed bridge). The discussion is intended to consider the future development of both bridges. Quoting a cable stayed bridge with a span length of 250 m that can be selected from either bridge, an evaluation was made by using calculations that uses the disaggregate behavioral model theory based on questionnaire responses from engineers. The analysis uses the following procedure: utility function values of the two term behavioral model (having two choices) are specified and the characteristics variables are selected; the data are prepared according to the specifications, which are used to estimate parameters by a maximum likelihood estimation method; and estimation amount is estimated by using the covariance matrix, which is given a `t` value verification. The conclusions: what gives the large effect to the selection is the engineering capacity and sociality; the result contains vocational consciousness; the economy is measured by the large weight of construction cost for the upper part structures and cost required for large repairs; materials affect largely the reliability, and so does the technological level the constructibility; the comprehensive technical capability, freedom in design and the experience attained by Japan have great effects in terms of technological capability. 10 refs., 10 figs., 11 tabs.

  19. Non-stoichiometry Defects and Radiation Hardness of Lead Tungstate Crystals PbWO4

    CERN Document Server

    Devitsin, E G; Kozlov, V A; Nefedov, L; Polyansky, E V; Potashov, S Yu; Terkulov, A R; Zadneprovski, B I

    2001-01-01

    It has been stated many times that the formation of radiation infringements in PbWO4 is to big extent stipulated by non-stoichiometry defects of the crystals, arising in the process of their growth and annealing. To refine the idea of characteristics of non-stoichiometry defects and their effect on the radiation hardness of PbWO4 the current study is aimed at the melt composition infringements during its evaporation and at optical transmission of crystals obtained in these conditions after their irradiation (137Cs source). In the optical transmission measurements along with traditional techniques a method "in situ" was used, which provided the measurements in fixed points of the spectrum (380, 470 and 535 nm) directly in the process of the irradiation. X-ray phase and fluorescence analysis of condensation products of vapours over PbWO4 melt has found PbWO4 phase in their content as well as compounds rich in lead, PbO, Pb2WO5, with overall ratio Pb/W = 3.2. Correspondingly the lack of lead and variations in th...

  20. Controlled synthesis of three-dimensional hierarchical Bi2WO6 microspheres with optimum photocatalytic activity

    International Nuclear Information System (INIS)

    Wang, Hong; Song, Jimei; Zhang, Hui; Gao, Fei; Zhao, Shaojuan; Hu, Haiqin

    2012-01-01

    Highlights: ► The synthesized method is very simple. It can be widely used in the production. ► The morphology is novel and the property is fine. ► The formation of 3D hierarchical microsphere can be induced by changing the concentration of KNO 3 . -- Abstract: Three-dimensional (3D) hierarchical Bi 2 WO 6 microsphere and octahedral Bi 2 WO 6 have been synthesized by a facile hydrothermal method using KNO 3 solution and distilled water as solvent, respectively. The obtained products were characterized by X-ray diffraction, scanning electron microscopy, N 2 adsorption/desorption, and UV–vis diffuse reflectance spectroscopy in detail. The concentration of KNO 3 played a key role in the formation of 3D hierarchical Bi 2 WO 6 microspheres. A possible formation mechanism of Bi 2 WO 6 microsphere was proposed. The photocatalytic activity of the as-synthesized products was evaluated by monitoring the degradation of MB solution under sunlight irradiation. It was found that the photocatalytic activity of the 3D hierarchical Bi 2 WO 6 microsphere was superior to the octahedral Bi 2 WO 6 , which was attributed to the larger surface area and special hierarchical structure of Bi 2 WO 6 microsphere.

  1. Incorporation of tantalum ions enhances the electrocatalytic activity of hexagonal WO3 nanowires for hydrogen evolution reaction

    International Nuclear Information System (INIS)

    Xie, Xiang; Mu, Wanjun; Li, Xingliang; Wei, Hongyuan; Jian, Yuan; Yu, Qianhong; Zhang, Rui; Lv, Kai; Tang, Hui; Luo, Shunzhong

    2014-01-01

    WO 3 has been identified as a promising candidate electrocatalyst for hydrogen evolution reaction (HER), because it can form a tungsten bronze (HxWO 3 ) which is highly electron and proton conducting. In this paper, we report that the electrocatalytic activity of WO 3 for HER can be enhanced by incorporation of tantalum ions (Ta 5+ ) into the lattice of WO 3 . The most active performance is achieved with the molar ratio of Ta/W being 0.01, which is two times more active than that of undoped WO 3 at an overpotential of -0.52 V. It is shown that incorporation of proper Ta 5+ into WO 3 can induce moderate defects and oxygen vacancies, as well as intercalate a higher amount of protons, which enhance the electron transfer and short the protons diffusion paths. These changes correlated positively with the enhanced catalytic HER activity. This study demonstrates, for the first time, that metal ions-doped WO 3 nanowires are promising electrocatalysts for HER

  2. Enhanced photoelectrochemical and photocatalytic activity of WO3-surface modified TiO2 thin film

    Science.gov (United States)

    Qamar, Mohammad; Drmosh, Qasem; Ahmed, Muhammad I.; Qamaruddin, Muhammad; Yamani, Zain H.

    2015-02-01

    Development of nanostructured photocatalysts for harnessing solar energy in energy-efficient and environmentally benign way remains an important area of research. Pure and WO3-surface modified thin films of TiO2 were prepared by magnetron sputtering on indium tin oxide glass, and photoelectrochemical and photocatalytic activities of these films were studied. TiO2 particles were <50 nm, while deposited WO3 particles were <20 nm in size. An enhancement in the photocurrent was observed when the TiO2 surface was modified WO3 nanoparticles. Effect of potential, WO3 amount, and radiations of different wavelengths on the photoelectrochemical activity of TiO2 electrodes was investigated. Photocatalytic activity of TiO2 and WO3-modified TiO2 for the decolorization of methyl orange was tested.

  3. On tungstates of divalent cations (II). Polymorphy of Pb{sub 2}WO{sub 5}

    Energy Technology Data Exchange (ETDEWEB)

    Jantz, Stephan G.; Dialer, Marwin; Hoeppe, Henning A. [Lehrstuhl fuer Festkoerperchemie, Universitaet Augsburg (Germany); Pielnhofer, Florian [Abteilung Nanochemie, Max-Planck-Institut fuer Festkoerperforschung, Stuttgart (Germany)

    2017-12-13

    The phase transition from the low temperature form Pb{sub 2}[WO{sub 5}] to its high temperature form Pb{sub 2}O[WO{sub 4}] was monitored by means of temperature dependent powder XRD. Single-crystals of Pb{sub 2}[WO{sub 5}], suitable for a structure determination by single-crystal X-ray diffraction, were obtained by quenching a sample from 500 C to room temperature. The low-temperature phase Pb{sub 2}[WO{sub 5}] comprises the structural motive of infinite zigzag chains built by cornersharing WO{sub 6} octahedra, known from the tungstates M{sub 2}[WO{sub 5}] (M = Sr, Ba), but crystallizes in a new structure type [C2/c, a = 14.0996(4) Aa, b = 5.8579(2) Aa, c = 12.6877(4) Aa, β = 114.3569(13) , Z = 8, R{sub int} = 0.042, R{sub 1} = 0.040, wR{sub 2} = 0.068]. The crystal structure of the high-temperature phase Pb{sub 2}O[WO{sub 4}] [C2/m, a = 14.2126(4) Aa, b = 5.80150(10) Aa, c = 7.3477(2) Aa, β = 113.9402(7) , Z = 4, R{sub 1} = 0.035, wR{sub 2} = 0.055] is revised, based on single-crystal XRD data. Furthermore spectroscopic data (IR, Raman and UV/Vis spectra) are presented. (copyright 2017 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  4. Understanding the Potential of WO3 Based Sensors for Breath Analysis

    Science.gov (United States)

    Staerz, Anna; Weimar, Udo; Barsan, Nicolae

    2016-01-01

    Tungsten trioxide is the second most commonly used semiconducting metal oxide in gas sensors. Semiconducting metal oxide (SMOX)-based sensors are small, robust, inexpensive and sensitive, making them highly attractive for handheld portable medical diagnostic detectors. WO3 is reported to show high sensor responses to several biomarkers found in breath, e.g., acetone, ammonia, carbon monoxide, hydrogen sulfide, toluene, and nitric oxide. Modern material science allows WO3 samples to be tailored to address certain sensing needs. Utilizing recent advances in breath sampling it will be possible in the future to test WO3-based sensors in application conditions and to compare the sensing results to those obtained using more expensive analytical methods. PMID:27801881

  5. Preparation and photoelectric properties of p-CaFe2O4/n-WO3 composites

    International Nuclear Information System (INIS)

    Wan, Ruiqin; Jia, Caihong; Zhang, Weifeng

    2012-01-01

    Highlights: ► Surface photovoltage spectroscopy investigation on p-CaFe 2 O 4 /n-WO 3 composites. ► The photovoltaic response is enhanced in p-CaFe 2 O 4 /n-WO 3 composites. ► The multielectron process and high rate of carrier migration in WO 3 . - Abstract: Composites of p-CaFe 2 O 4 /n-WO 3 are prepared via a sol–gel technique. Their structures and optical properties are characterized with X-ray diffraction, scanning electron microscopy and UV–vis absorption spectroscopy. The photoelectric characteristics are investigated by surface photovoltage spectroscopy combined with electric field induced surface photovoltage spectroscopy. The results indicate that CaFe 2 O 4 can well form a p–n type composite with WO 3 , and the intensity and spectral region of surface photovoltaic response for the composites are strongly dependent on the molar ratio of two components. The enhancement in photoelectric properties and the effective separation of photogenerated carriers could be attributed to the energy level matching between the two components, multielectron process and the high migration rate in WO 3 .

  6. Magnetic properties of the strongly correlated chain antiferromagnet KTb(WO4)2

    International Nuclear Information System (INIS)

    Khatsko, E.; Loginov, A.; Cherny, A.; Rykova, A.

    2006-01-01

    The susceptibility and magnetization of a single crystal of KTb(WO 4 ) 2 has been measured in the temperature range 0.5-80 K in magnetic fields up to 6 T. It is shown that KTb(WO 4 ) 2 is an Ising magnet with only one component of the magnetic moment. The three-dimensional phase transition to the antiferromagnetically ordered state has been found below 0.7 K. This transition can be described in the molecular field two-level approximation. The principal exchange constant has been estimated. By using experimental data the magnetic structure of KTb(WO 4 ) 2 is proposed

  7. Charge doping and large lattice expansion in oxygen-deficient heteroepitaxial WO3

    Science.gov (United States)

    Mattoni, Giordano; Filippetti, Alessio; Manca, Nicola; Zubko, Pavlo; Caviglia, Andrea D.

    2018-05-01

    Tungsten trioxide (WO3) is a versatile material with widespread applications ranging from electrochromics and optoelectronics to water splitting and catalysis of chemical reactions. For technological applications, thin films of WO3 are particularly appealing, taking advantage from a high surface-to-volume ratio and tunable physical properties. However, the growth of stoichiometric crystalline thin films is challenging because the deposition conditions are very sensitive to the formation of oxygen vacancies. In this paper, we show how background oxygen pressure during pulsed laser deposition can be used to tune the structural and electronic properties of WO3 thin films. By performing x-ray diffraction and low-temperature electrical transport measurements, we find changes in the WO3 lattice volume of up to 10% concomitantly with a resistivity drop of more than five orders of magnitude at room temperature as a function of increased oxygen deficiency. We use advanced ab initio calculations to describe in detail the properties of the oxygen vacancy defect states and their evolution in terms of excess charge concentration. Our results depict an intriguing scenario where structural, electronic, optical, and transport properties of WO3 single-crystal thin films can all be purposely tuned by controlling the oxygen vacancy formation during growth.

  8. Inductive effect of poly(vinyl pyrrolidone) on morphology and photocatalytic performance of Bi{sub 2}WO{sub 6}

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Qiang; Chen, Jinxing; Xie, Yunyun; Wang, Mozhen; Ge, Xuewu, E-mail: xwge@ustc.edu.cn

    2016-04-15

    Graphical abstract: - Highlights: • PVP molecular chains will induce the assembly of the primary Bi{sub 2}WO{sub 6} nanosheets. • The assembly of primary Bi{sub 2}WO{sub 6} nanosheets forms various 3D topological structure. • Sheet-like, flower-like, red-blood-cell-like and square-pillar-like Bi{sub 2}WO{sub 6} were formed. • Bi{sub 2}WO{sub 6} formed at low concentration or molecular weight of PVP has better activity. - Abstract: Bi{sub 2}WO{sub 6} has great potential applications in the field of photocatalyst due to its excellent visible-light photocatalytic performance. This work studied the detailed morphological evolution of Bi{sub 2}WO{sub 6} particles synthesized in a simple hydrothermal system induced by the stabilizer poly(vinyl pyrrolidone) (PVP). The XRD and HRTEM results show PVP would not change the crystal structure of Bi{sub 2}WO{sub 6}, but the distribution of PVP on the initially formed Bi{sub 2}WO{sub 6} nanosheets will induce the crystal growth, resulting in a distinct morphology evolution of Bi{sub 2}WO{sub 6} with the increase of the concentration of PVP. At the same time, with the increase of the molecular weight of PVP, the morphology of Bi{sub 2}WO{sub 6} varied from simple sheet-like (S-BWO) to some complicated morphology, such as flower-like (F-BWO), red blood cell-like (B-BWO), and square-pillar-like (SP-BWO). The photocatalytic performances of Bi{sub 2}WO{sub 6} with various morphologies on the decomposition of RhB under visible light irradiation reveal that S-BWO has the best photocatalytic performance, while SP-BWO has the worst. This work not only gives the explanation of the inductive effect of PVP molecular chains on the morphological formation of Bi{sub 2}WO{sub 6} particles, but also provides the controllable way to the preparation of Bi{sub 2}WO{sub 6} with various morphologies taking advantage of the stabilizer PVP.

  9. Preparation of WO{sub 3}/g-C{sub 3}N{sub 4} composites and their application in oxidative desulfurization

    Energy Technology Data Exchange (ETDEWEB)

    Zhao, Rongxiang, E-mail: zylhzrx@126.com; Li, Xiuping, E-mail: lilili_171717@126.com; Su, Jianxun; Gao, Xiaohan

    2017-01-15

    Highlights: • The WO{sub 3}/g-C{sub 3}N{sub 4} was successfully synthesized through simple calcination. • The process is simple and the cost raw materials is cheap. • The WO{sub 3}/g-C{sub 3}N{sub 4} firstly applied to ODS. • The desulpurization rate of WO{sub 3}/g-C{sub 3}N{sub 4} may attach to 91.2%. • Five recycles of WO{sub 3}/g-C{sub 3}N{sub 4} still attach to 89.5% due to heterogeneous catalysis. - Abstract: WO{sub 3}/graphitic carbon nitride (g-C{sub 3}N{sub 4}) composites were successfully synthesized through direct calcining of a mixture of WO{sub 3} and g-C{sub 3}N{sub 4} at 400 °C for 2 h. The WO{sub 3} was prepared by calcination of phosphotungstic acid at 550 °C for 4 h, and the g-C{sub 3}N{sub 4} was obtained by calcination of melamine at 520 °C for 4 h. The WO{sub 3}/g-C{sub 3}N{sub 4} composites were characterized by X-ray diffraction (XRD), Scanning electron microscopy (SEM), Fourier-transform infrared spectroscopy (FT-IR), and Brunner−Emmett−Teller analysis (BET). The WO{sub 3}/g-C{sub 3}N{sub 4} composites exhibited stronger XRD peaks of WO{sub 3} and g-C{sub 3}N{sub 4} than the WO{sub 3} and pure g-C{sub 3}N{sub 4}. In addition, two WO{sub 3} peaks at 25.7° and 26.6° emerged for the 36% −WO{sub 3}/g-C{sub 3}N{sub 4} composite. This finding indicated that WO{sub 3} was highly dispersed on the surface of the g-C{sub 3}N{sub 4} nanosheets and interacted with the nanosheets, which resulted in the appearance of (012) and (022) planes of WO{sub 3}. The WO{sub 3}/g-C{sub 3}N{sub 4} composite also exhibited a larger specific surface area and higher degree of crystallization than WO{sub 3} or pure g-C{sub 3}N{sub 4}, which resulted in high catalytic activity of the catalyst. Desulfurization experiments demonstrated that the desulfurization rate of dibenzothiophene (DBT) in model oil reached 91.2% under optimal conditions. Moreover, the activity of the catalyst was not significantly decreased after five recycles.

  10. WO-Type Wolf-Rayet Stars: the Last Hurrah of the Most Massive Stars?

    Science.gov (United States)

    Massey, Philip

    2014-10-01

    WO-type Wolf-Rayet (WR) stars are considered the final evolutionary stage of the highest mass stars, immediate precursors to Type Ic (He-poor) core-collapse supernovae. These WO stars are rare, and until recently only 6 were known. Our knowledge about their physical properties is mostly based on a single object, Sand 2 in the LMC. It was the only non-binary WO star both bright and unreddened enough that its FUV and NUV spectra could be obtained by FUSE and HST/FOS. A non-LTE analysis showed that Sand 2 is very hot and its (C+O)/He abundance ratio is higher than that found in WC-type WRs, suggesting it is indeed highly evolved. However, the O VI resonance doublet in the FUV required a considerably cooler temperature (120,000 K) model than did the optical O VI lines (170,000 K). Further, the enhanced chemical abundances did not match the predictions of stellar evolutionary models. Another non-LTE study found a 3x higher (C+O)/He abundance ratio and a cooler temperature. We have recently discovered two other bright, single, and lightly reddened WOs in the LMC, allowing us to take a fresh look at these important objects. Our newly found WOs span a range in excitation type, from WO1 (the highest) to WO4 (the lowest). Sand 2 is intermediate (WO3). We propose to use COS to obtain FUV and NUV data of all three stars for as comprehensive a study as is currently possible. These UV data will be combined with our optical Magellan spectra for a detailed analysis with CMFGEN with the latest atomic data. Knowing the degree of chemical evolution of these WO stars is crucial to determining their evolutionary status, and thus in understanding the final stages of the most massive stars.

  11. Synthesis, characterization and photocatalytic activity of porous WO{sub 3}/TiO{sub 2} hollow microspheres

    Energy Technology Data Exchange (ETDEWEB)

    Yang, Liuyang [Graduate School at Shenzhen, Tsinghua University, Shenzhen 518055 (China); Si, Zhichun, E-mail: emsztsinghua@126.com [Graduate School at Shenzhen, Tsinghua University, Shenzhen 518055 (China); Weng, Duan [Graduate School at Shenzhen, Tsinghua University, Shenzhen 518055 (China); State Key Laboratory of New Ceramics and Fine Process, School of Materials Science and Engineering, Tsinghua University, Beijing 100084 (China); Yao, Youwei [Graduate School at Shenzhen, Tsinghua University, Shenzhen 518055 (China)

    2014-09-15

    Porous WO{sub 3}/TiO{sub 2} hollow microspheres were prepared by a spray drying method for photodegradation of methylene blue and phenol. The catalysts were characterized by X-ray diffraction, Field Emission Scanning Electron Microscope, High Resolution Transmission Electron Microscope, N{sub 2} adsorption–desorption measurements, Raman spectrometer, UV–Vis Diffuse Reflectance Spectroscopy and Zeta-Meter measurements. The results showed that the tungsten oxides mainly existed in highly dispersed amorphous form on anatase when the loading amount of tungsten oxide was below 3 mol%. The improved photocatalytic activity under UV light irradiation of the WO{sub 3}/TiO{sub 2} catalyst mainly arises from the enhanced charge separation efficiency rather than the improved light absorbance by highly dispersed amorphous tungsten oxides. Highly dispersed amorphous WO{sub x} can form a shallowly trapped site due to its similar band structure with TiO{sub 2}. The strongly electron-withdrawing of tungsten oxide in highly dispersed state facilitates the electron transition between titanium and WO{sub x}, and consequently improves the charge separation. The enhanced acidity of catalyst by WO{sub x} in reactant environment also improved the charge separation efficiency due to the timely transition of holes and electrons accumulated on TiO{sub 2} and WO{sub x}, respectively. However, the improved photocatalytic activity under visible light irradiation of the WO{sub 3}/TiO{sub 2} catalyst mainly arises from light harvest. TiO{sub 2} containing 3 mol% WO{sub 3} displayed the highest photocatalytic activity under UV light irradiation while that containing 4 mol% WO{sub 3} present highest activity under visible light irradiation.

  12. High photocatalytic performance of BiOI/Bi{sub 2}WO{sub 6} toward toluene and Reactive Brilliant Red

    Energy Technology Data Exchange (ETDEWEB)

    Li Huiquan [School of Chemistry and Chemical Engineering, Fuyang Normal College, Fuyang 236041 (China); Key Laboratory of Mesoscopic Chemistry of MOE, Jiangsu Provincial Key Laboratory of Nanotechnology, School of Chemistry and Chemical Engineering, Nanjing University, Nanjing 210093 (China); Cui Yumin, E-mail: cuiyumin0908@163.com [School of Chemistry and Chemical Engineering, Fuyang Normal College, Fuyang 236041 (China); Hong Wenshan [School of Chemistry and Chemical Engineering, Fuyang Normal College, Fuyang 236041 (China)

    2013-01-01

    Graphical abstract: When BiOI/Bi{sub 2}WO{sub 6} catalyst was exposed to UV or visible light, the electrons in the valence band of Bi{sub 2}WO{sub 6} would be excited into the conduction band and then injected into the more positive conduction band of BiOI. Therefore, the photoelectrons were generated from Bi{sub 2}WO{sub 6} and transferred across the interface between BiOI and Bi{sub 2}WO{sub 6} to the surface of BiOI, leaving the photogenerated holes in the valence band of Bi{sub 2}WO{sub 6}. In this way, the photoinduced electron-hole pairs were effectively separated. Highlights: Black-Right-Pointing-Pointer BiOI sensitized Bi{sub 2}WO{sub 6} catalysts were successfully prepared by a facile method. Black-Right-Pointing-Pointer The 13.2% BiOI/Bi{sub 2}WO{sub 6} catalyst exhibits higher photoactivities than P25. Black-Right-Pointing-Pointer A possible transfer process of photogenerated carriers was proposed. - Abstract: BiOI sensitized nano-Bi{sub 2}WO{sub 6} photocatalysts with different BiOI contents were successfully synthesized by a facile deposition method at room temperature, and characterized by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS) high-resolution transmission electron microscopy (HR-TEM), photoluminescence (PL) spectra, UV-vis diffuse reflection spectroscopy (UV-vis DRS) and Brunauer-Emmett-Teller (BET) surface area measurements. The photocatalytic activity of BiOI/Bi{sub 2}WO{sub 6} was evaluated by the photo-degradation of Reactive Brilliant Red (X-3B) in suspended solution and toluene in gas phase. It has been shown that the BiOI/Bi{sub 2}WO{sub 6} catalysts exhibit a coexistence of both tetragonal BiOI and orthorhombic Bi{sub 2}WO{sub 6} phases. With increasing BiOI content, the absorption intensity of BiOI/Bi{sub 2}WO{sub 6} catalysts increases in the 380-600 nm region and the absorption edge shifts significantly to longer wavelengths as compared to pure Bi{sub 2}WO{sub 6}. The 13.2% BiOI/Bi{sub 2}WO{sub 6} catalyst exhibits

  13. A Facile Synthesis of Graphene-WO3 Nanowire Clusters with High Photocatalytic Activity for O2 Evolution

    Directory of Open Access Journals (Sweden)

    M.-J. Zhou

    2014-01-01

    Full Text Available In the present work, graphene-WO3 nanowire clusters were synthesized via a facile hydrothermal method. The obtained graphene-WO3 nanowire clusters were characterized by X-ray diffraction (XRD, transmission electron microscopy (TEM, X-ray photoelectron spectroscopy (XPS, Fourier transform infrared spectroscopy (FT-IR, Raman spectroscopy, and ultraviolet-visible diffuse reflectance spectroscopy (DRS techniques. The photocatalytic oxygen (O2 evolution properties of the as-synthesized samples were investigated by measuring the amount of evolved O2 from water splitting. The graphene-WO3 nanowire clusters exhibited enhanced performance compared to pure WO3 nanowire clusters for O2 evolution. The amount of evolved O2 from water splitting after 8 h for the graphene-WO3 nanowire clusters is ca. 0.345 mmol/L, which is more than 1.9 times as much as that of the pure WO3 nanowire clusters (ca. 0.175 mmol/L. The high photocatalytic activity of the graphene-WO3 nanowire clusters was attributed to a high charge transfer rate in the presence of graphene.

  14. On tungstates of divalent cations (I). Structural investigation and spectroscopic properties of Sr{sub 2}[WO{sub 5}] and Ba{sub 2}[WO{sub 5}

    Energy Technology Data Exchange (ETDEWEB)

    Jantz, Stephan G.; Dialer, Marwin; Hoeppe, Henning A. [Lehrstuhl fuer Festkoerperchemie, Universitaet Augsburg (Germany); Pielnhofer, Florian [Abteilung Nanochemie, Max-Planck-Institut fuer Festkoerperforschung, Stuttgart (Germany)

    2017-12-13

    The crystal structures of Sr{sub 2}[WO{sub 5}] [Pna2{sub 1}, a = 7.2457(3) Aa, b = 10.8867(5) Aa, c = 5.5391(3) Aa, Z = 4, R{sub int} = 0.0671, R{sub 1} = 0.0495, wR{sub 2} = 0.0462] and Ba{sub 2}[WO{sub 5}] [Pnma, a = 7.3828(2) Aa, b = 5.71420(10) Aa, c = 11.4701(3) Aa, Z = 4, R{sub int} = 0.0294, R{sub 1} = 0.0146, wR{sub 2} = 0.0284] are revised, based on single-crystal XRD data. Furthermore spectroscopic data (infrared, Raman, and UV/Vis) assisted by DFT calculations are discussed and first results on the luminescence properties of Sr{sub 2}[WO{sub 5}]:Eu{sup 3+} are presented. (copyright 2017 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  15. Intrinsic Defects and H Doping in WO3

    KAUST Repository

    Zhu, Jiajie

    2017-01-18

    WO3 is widely used as industrial catalyst. Intrinsic and/or extrinsic defects can tune the electronic properties and extend applications to gas sensors and optoelectonics. However, H doping is a challenge to WO3, the relevant mechanisms being hardly understood. In this context, we investigate intrinsic defects and H doping by density functional theory and experiments. Formation energies are calculated to determine the lowest energy defect states. O vacancies turn out to be stable in O-poor environment, in agreement with X-ray photoelectron spectroscopy, and O-H bond formation of H interstitial defects is predicted and confirmed by Fourier transform infrared spectroscopy.

  16. CdWO{sub 4}-on-MEH-PPV:PS as a candidate for real-time dosimeters

    Energy Technology Data Exchange (ETDEWEB)

    Silva, M.M. [Laboratory of Polymers and Electronic Properties of Materials, UFOP, 35400-000 (Brazil); Novais, S.M.V.; Silva, E.S.S. [Group of Advanced Ceramic Materials, UFS, 49100-000 (Brazil); Schimitberger, T. [Laboratory of Polymers and Electronic Properties of Materials, UFOP, 35400-000 (Brazil); Macedo, Z.S. [Group of Advanced Ceramic Materials, UFS, 49100-000 (Brazil); Bianchi, R.F., E-mail: bianchi@iceb.ufop.br [Laboratory of Polymers and Electronic Properties of Materials, UFOP, 35400-000 (Brazil)

    2012-10-15

    We report on the investigations about the modification of optical properties induced by X-rays onto film detectors of cadmium tungstate (CdWO{sub 4}), poly[2-methoxy-5(2 Prime -ethylhexyloxy)-p-phenylenevinylene] (MEH-PPV) and polystyrene (PS) This device takes advantage of reduction of spectral overlap between the radioluminescence (RL) of CdWO{sub 4} and the absorption of MEH-PPV as it is exposed to radiation, forming the basis of a new dosimeter that is capable of converting the orange-red radioluminescence of PS:MEH-PPV:CdWO{sub 4} into green. We propose an explanation of the optical processes occurring in MEH-PPV:CdWO{sub 4} in terms of the radiation hardness of CdWO{sub 4} combined to the RL-induced degradation of MEH-PPV. Highlights: Black-Right-Pointing-Pointer Thin composite film dosimeters using a combination of a scintillator crystal and a light-emitting polymer. Black-Right-Pointing-Pointer A X-ray dose detector based on MEH-PPV/CdWO{sub 4} materials which are rarely seen together. Black-Right-Pointing-Pointer A new smart, disposable and easy-to-read organic-inorganic radiation detector.

  17. Ag loaded WO{sub 3} nanoplates for efficient photocatalytic degradation of sulfanilamide and their bactericidal effect under visible light irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Zhu, Wenyu [School of Civil and Environmental Engineering, Nanyang Technological University, 50 Nanyang Avenue, Singapore 639798 (Singapore); Nanyang Environment and Water Research Institute (NEWRI), Nanyang Technological University, 1 Cleantech Loop, CleanTech One, Singapore 637141 (Singapore); Liu, Jincheng, E-mail: JCLIU@ntu.edu.sg [School of Civil and Environmental Engineering, Nanyang Technological University, 50 Nanyang Avenue, Singapore 639798 (Singapore); Current address: Faculty of Chemical Engineering and Light Industry, Guangdong University of Technology, Guangzhou 510009 (China); Yu, Shuyan; Zhou, Yan [School of Civil and Environmental Engineering, Nanyang Technological University, 50 Nanyang Avenue, Singapore 639798 (Singapore); Nanyang Environment and Water Research Institute (NEWRI), Nanyang Technological University, 1 Cleantech Loop, CleanTech One, Singapore 637141 (Singapore); Yan, Xiaoli, E-mail: XLYAN@ntu.edu.sg [School of Civil and Environmental Engineering, Nanyang Technological University, 50 Nanyang Avenue, Singapore 639798 (Singapore); Current address: Environmental and Water Technology Centre of Innovation, Ngee Ann Polytechnic, 535 Clementi Road, Singapore 599489 (Singapore)

    2016-11-15

    Highlights: • WO{sub 3}/Ag heterogeneous composites were fabricated with simply photo-reduction method. • Property changes due to Ag loading were systematically studied. • WO{sub 3}/Ag composites efficiently degraded sulfanilamide under visible light irradiation. • WO{sub 3}/Ag composites exhibited bactericidal effectS under visible light irradiation. - Abstract: Sulfonamides (SAs) are extensively used antibiotics and their residues in the water bodies propose potential threat to the public. In this study, degradation efficiency of sulfanilamide (SAM), which is the precursor of SAs, using WO{sub 3} nanoplates and their Ag heterogeneous as photocatalysts was investigated. WO{sub 3} nanoplates with uniform size were synthesized by a facile one step hydrothermal method. Different amount of Ag nanoparticles (Ag NPs) were loaded onto WO{sub 3} nanoplates using a photo-reduction method to generate WO{sub 3}/Ag composites. The physio-chemical properties of synthesized nanomaterials were systematically characterized. Photodegradation of SAM by WO{sub 3} and WO{sub 3}/Ag composites was conducted under visible light irradiation. The results show that WO{sub 3}/Ag composites performed much better than pure WO{sub 3} where the highest removal rate was 96.2% in 5 h. Ag as excellent antibacterial agent also endows certain antibacterial efficiency to WO{sub 3}, and 100% removal efficiency against Escherichia Coli and Bacillus subtilis could be achieved in 2 h under visible light irradiation for all three WO{sub 3}/Ag composites synthesized. The improved performance in terms of SAM degradation and antibacterial activity of WO{sub 3}/Ag can be attributed to the improved electron-hole pair separation rate where Ag NPs act as effective electron trapper during the photocatalytic process.

  18. Influence of Liquid Petroleum Gas on the Electrical Parameters of the WO3 Thick Film

    Directory of Open Access Journals (Sweden)

    R. S. KHADAYATE

    2007-02-01

    Full Text Available In this work, the WO3 thick films were prepared by standard screen-printing technology. These films were characterized by x-ray diffraction (XRD measurements and scanning electron microscopy (SEM. Influence of LPG on the electrical properties of the prepared WO3 thick film is reported. It was observed that the slope of the Arrhenius curves of the WO3 thick film decreased as the medium changed from pure air to 100 ppm LPG in air. From I-V characteristics, it was observed that the WO3 thick film exhibit highest sensitivity to 50 ppm LPG in air at 400oC.

  19. Enhanced structural and optical properties of the polyaniline-calcium tungstate (PANI-CaWO4 nanocomposite for electronics applications

    Science.gov (United States)

    Sabu, N. Aloysius; Francis, Xavier; Anjaly, Jose; Sankararaman, S.; Varghese, Thomas

    2017-06-01

    In this article, we report the synthesis and characterization of polyaniline-calcium tungstate nanocomposite, a novel material for potential applications. The PANI-CaWO4 nanocomposite was prepared by in situ oxidative polymerization of aniline in the presence of CaWO4 nanoparticles dispersed in ethanol. Investigations using X-ray diffraction, Fourier-transformed infrared spectroscopy, UV-visible, photoluminescence and Raman spectroscopy confirmed the formation of the nanocomposite of PANI with CaWO4 nanoparticles. Scanning electron microscopy revealed almost uniform distribution of CaWO4 nanoparticles in the polyaniline matrix. These studies also confirmed electronic structure modification as a result of incorporating CaWO4 nanoparticles in PANI. Composite formation resulted in large decrease in the optical band gap and enhanced photoluminescence. The augmented structural, optical and photoluminescence properties of the PANI-CaWO4 nanocomposite can be used to explore potential applications in micro- and optoelectronics. This is the first report presenting synthesis and characterization of the PANI-CaWO4 nanocomposite.

  20. Investigation of the optical property and structure of WO3 thin films with different sputtering depositions

    Science.gov (United States)

    Chen, Hsi-Chao; Jan, Der-Jun; Chen, Chien-Han; Huang, Kuo-Ting; Lo, Yen-Ming; Chen, Sheng-Hui

    2011-09-01

    The purpose of this research was to compare the optical properties and structure of tungsten oxide (WO3) thin films that was deposited by different sputtering depositions. WO3 thin films deposited by two different depositions of direct current (DC) magnetron sputtering and pulsed DC sputtering. A 99.95% WO3 target was used as the starting material for these depositions. These WO3 thin films were deposited on the ITO glass, PET and silicon substrate by different ratios of oxygen and argon. A shadow moiré interferometer would be introduced to measure the residual stress for PET substrate. RF magnetron sputtering had the large residual stress than the other's depositions. A Raman spectrum could exhibit the phase of oxidation of WO3 thin film by different depositions. At the ratio of oxygen and argon was about 1:1, and the WO3 thin films had the best oxidation. However, it was important at the change of the transmittance (ΔT = Tbleached - Tcolored) between the coloring and bleaching for the smart window. Therefore, we also found the WO3 thin films had the large variation of transmittance between the coloring and bleaching at the gas ratios of oxygen and argon of 1:1.

  1. Photoreduction of non-noble metal Bi on the surface of Bi{sub 2}WO{sub 6} for enhanced visible light photocatalysis

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Xiaojing [State Key Laboratory of Oil and Gas Reservoir Geology and Exploitation, Southwest Petroleum University, No. 8, Xindu Road, Xindu District, Chengdu 610500 (China); The Center of New Energy Materials and Technology, School of Materials Science and Engineering, Southwest Petroleum University, No. 8, Xindu Road, Xindu District, Chengdu 610500 (China); Yu, Shan; Liu, Yang; Zhang, Qian [The Center of New Energy Materials and Technology, School of Materials Science and Engineering, Southwest Petroleum University, No. 8, Xindu Road, Xindu District, Chengdu 610500 (China); Zhou, Ying, E-mail: yzhou@swpu.edu.cn [State Key Laboratory of Oil and Gas Reservoir Geology and Exploitation, Southwest Petroleum University, No. 8, Xindu Road, Xindu District, Chengdu 610500 (China); The Center of New Energy Materials and Technology, School of Materials Science and Engineering, Southwest Petroleum University, No. 8, Xindu Road, Xindu District, Chengdu 610500 (China)

    2017-02-28

    Highlights: • Bi{sub 2}WO{sub 6}-Bi composite was synthesized by in situ photoreduction of Bi{sub 2}WO{sub 6}. • Bi{sub 2}WO{sub 6}-Bi exhibits improved photocatalytic efficiency towards degradation of Rhodamine B. • The generation of elemental Bi in Bi{sub 2}WO{sub 6}-Bi induces vacancy and structure distortion of Bi{sub 2}WO{sub 6}. • The surface oxygen adsorption mode changes from hydroxyl group on Bi{sub 2}WO{sub 6} to molecular oxygen on Bi{sub 2}WO{sub 6}-Bi. - Abstract: In this report, Bi{sub 2}WO{sub 6}-Bi composite was prepared through an in situ photoreduction method and was characterized systematically by X-Ray diffraction, transmission electron microscopy, X-Ray photoelectron spectroscopy and UV-vis diffuse reflectance spectroscopy. The as-prepared Bi{sub 2}WO{sub 6}-Bi maintains the same crystal structure with the pristine Bi{sub 2}WO{sub 6} regardless of some surface defects. Nevertheless, these surface defects result in the change of surface oxygen adsorption mode from hydroxyl to molecular oxygen on Bi{sub 2}WO{sub 6}. Photocatalytic activity over Bi{sub 2}WO{sub 6}-Bi is 2.4 times higher than that of Bi{sub 2}WO{sub 6} towards the degradation of organic dye Rhodamine B (RhB) under visible light irradiation (λ > 420 nm). A deep study shows that cleavage of benzene ring is the main pathway for RhB degradation over Bi{sub 2}WO{sub 6}, but both the benzene cleavage and de-ethylation pathway coexist for RhB decomposition in the presence of Bi{sub 2}WO{sub 6}-Bi as the photocatalyst. Photoelectrochemical study including transient photocurrent tests and electrochemical impedance spectroscopy measurements shows that Bi{sub 2}WO{sub 6}-Bi could facilitate the charge transfer process compared to Bi{sub 2}WO{sub 6}. These data above has indicated a new insight into the promotion mechanism based on Bi related heterostructures.

  2. Morphology-controlled synthesis of CdWO4 nanorods and nanoparticles via a molten salt method

    International Nuclear Information System (INIS)

    Wang Yonggang; Ma Junfeng; Tao Jiantao; Zhu Xiaoyi; Zhou Jun; Zhao Zhongqiang; Xie Lijin; Tian Hua

    2006-01-01

    Cadmium tungstate (CdWO 4 ) nanoparticles and nanorods have been successfully synthesized by a molten salt method at 270 deg. C, and the morphology of the nanocrystals can be controlled by adjusting such reaction conditions as the calcined time and the weight ratio of the salt to the CdWO 4 precursor. The resultant sample is a pure phase of CdWO 4 without any other impurities

  3. Non-stoichiometry defects and radiation hardness of lead tungstate crystals PbWO sub 4

    CERN Document Server

    Devitsin, E G; Potashov, S Yu; Terkulov, A R; Nefedov, V A; Polyansky, E V; Zadneprovski, B I; Kjellberg, P; Korbel, V

    2002-01-01

    It has been stated many times that the formation of radiation infringements in PbWO sub 4 is to a big extent stipulated by the non-stoichiometry defects of the crystals, arising in the process of their growth and annealing. To refine the idea of characteristics of the non-stoichiometry defects and their effect on the radiation hardness of PbWO sub 4 , the current study is aimed at the melt composition infringements during its evaporation and at optical transmission of crystals obtained in these conditions after their irradiation ( sup 1 sup 3 sup 7 Cs source). In the optical transmission measurements along with traditional techniques a method 'in situ' was used, which provided the measurements in fixed points of the spectrum (380, 470 and 535 nm) directly in the process of the irradiation. X-ray phase and fluorescence analysis of condensation products of vapours over PbWO sub 4 melt has found PbWO sub 4 phase in their content as well as compounds rich in lead PbO, Pb sub 2 WO sub 5 with overall ratio Pb/W (3....

  4. WO3 nanorods-modified carbon electrode for sustained electron uptake from Shewanella oneidensis MR-1 with suppressed biofilm formation

    International Nuclear Information System (INIS)

    Zhang, Feng; Yuan, Shi-Jie; Li, Wen-Wei; Chen, Jie-Jie; Ko, Chi-Chiu; Yu, Han-Qing

    2015-01-01

    Highlights: • WO 3 nanorods-modified carbon paper was used as the anode of MFC. • WO 3 nanorods suppressed biofilm growth on the electrode surface. • Sustained electron transfer from cells to electrode via riboflavin was achieved. • C–WO 3 nanorods enable stable and efficient EET process in long-time operation. - Abstract: Carbon materials are widely used as electrodes for bioelectrochemical systems (BES). However, a thick biofilm tends to grow on the electrode surface during continuous operation, resulting in constrained transport of electrons and nutrients at the cell-electrode interface. In this work, we tackled this problem by adopting a WO 3 -nanorods modified carbon electrode (C–WO 3 nanorods), which completely suppressed the biofilm growth of Shewanella Oneidensis MR-1. Moreover, the C–WO 3 nanorods exhibited high electric conductivity and strong response to riboflavin. These two factors together make it possible for the C–WO 3 nanorods to maintain a sustained, efficient process of electron transfer from the MR-1 planktonic cells. As a consequence, the microbial fuel cells with C–WO 3 nanorods anode showed more stable performance than the pure carbon paper and WO 3 -nanoparticles systems in prolonged operation. This work suggests that WO 3 nanorods have the potential to be used as a robust and biofouling-resistant electrode material for practical bioelectrochemical applications

  5. Degradation of organic dyes using spray deposited nanocrystalline stratified WO3/TiO2 photoelectrodes under sunlight illumination

    Science.gov (United States)

    Hunge, Y. M.; Yadav, A. A.; Mahadik, M. A.; Bulakhe, R. N.; Shim, J. J.; Mathe, V. L.; Bhosale, C. H.

    2018-02-01

    The need to utilize TiO2 based metal oxide hetero nanostructures for the degradation of environmental pollutants like Rhodamine B and reactive red 152 from the wastewater using stratified WO3/TiO2 catalyst under sunlight illumination. WO3, TiO2 and stratified WO3/TiO2 catalysts were prepared by a spray pyrolysis method. It was found that the stratified WO3/TiO2 heterostructure has high crystallinity, no mixed phase formation occurs, strong optical absorption in the visible region of the solar spectrum, and large surface area. The photocatalytic activity was tested for degradation of Rhodamine B (Rh B) and reactive red 152 in an aqueous medium. TiO2 layer in stratified WO3/TiO2 catalyst helps to extend its absorption spectrum in the solar light region. Rh B and Reactive red 152is eliminated up to 98 and 94% within the 30 and 40 min respectively at optimum experimental condition by stratified WO3/TiO2. Moreover, stratified WO3/TiO2 photoelectrode has good stability and reusability than individual TiO2 and WO3 thin film in the degradation of Rh B and reactive red 152. The photoelectrocatalytic experimental results indicate that stratified WO3/TiO2 photoelectrode is a promising material for dye removal.

  6. Ultrasensitive ppb-level NO2 gas sensor based on WO3 hollow nanosphers doped with Fe

    Science.gov (United States)

    Zhang, Ziyue; haq, Mahmood; Wen, Zhen; Ye, Zhizhen; Zhu, Liping

    2018-03-01

    WO3 mesoporous hollow nanospheres doped with Fe synthesized by a facile method have mesoporous hollow nanospherical like morphology, small grain size (10 nm), high crystalline quality and ultrahigh surface area (165 m2/g). XRD spectra and Raman spectra indicate the Fe doping leading to the smaller cell parameters as compared to pure WO3, and the slight distortion in the crystal lattice produces a number of defects, making it a better candidate for gas sensing. XPS analysis shows that Fe-doped WO3 mesoporous hollow nanospheres have more oxygen vacancies than pure WO3, which is beneficial to the adsorption of oxygen and NO2 and its surface reaction. The gas sensor based on Fe-WO3 exhibited excellent low ppb-level (10 ppb) NO2 detecting performance and outstanding selectivity.

  7. Eliminating degradation and uncovering ion-trapping dynamics in electrochromic WO3 thin films

    Science.gov (United States)

    Wen, Rui-Tao; Granqvist, Claes G.; Niklasson, Gunnar A.

    2015-01-01

    Amorphous WO3 thin films are of keen interest as cathodic electrodes in transmittance-modulating electrochromic devices. However, these films suffer from ion-trapping-induced degradation of optical modulation and reversibility upon extended Li+-ion exchange. Here, we demonstrate that ion-trapping-induced degradation, which is commonly believed to be irreversible, can be successfully eliminated by constant-current-driven de-trapping, i.e., WO3 films can be rejuvenated and regain their initial highly reversible electrochromic performance. Pronounced ion-trapping occurs when x exceeds ~0.65 in LixWO3 during ion insertion. We find two main kinds of Li+-ion trapping sites (intermediate and deep) in WO3, where the intermediate ones are most prevalent. Li+-ions can be completely removed from intermediate traps but are irreversibly bound in deep traps. Our results provide a general framework for developing and designing superior electrochromic materials and devices. PMID:26259104

  8. Evaluate humidity sensing properties of novel TiO2–WO3 composite material

    International Nuclear Information System (INIS)

    Lin, Wang-De; Lai, De-Sheng; Chen, Min-Hung; Wu, Ren-Jang; Chen, Fu-Chou

    2013-01-01

    Graphical abstract: TiO 2 –WO 3 (1:1) showed better humidity sensing properties than others within the range of 12–90% relative humidity (RH), the response and recovery time were about 20 s and 160 s, respectively. Compared to the previous studies, the prepared sensor exhibits higher sensitivity (S = 451) and the low hysteresis value was around 0.13% at 32% RH. - Highlights: • Novel TiO 2 –WO 3 composite material was prepared for humidity sensor. • The sensor exhibits higher sensitivity (S = 451). • Low hysteresis value was around 0.13% at 32% RH. - Abstract: A novel TiO 2 –WO 3 composite material was prepared using a different proportion of TiO 2 and WO 3 to that investigated in previous studies. The obtained mesoporous material was characterized using X-ray diffraction, Fourier transform infrared spectrometry, transmission electron microscopy, energy dispersive X-ray spectroscopy, and N 2 adsorption-desorption techniques. The humidity-sensing properties were measured using an inductance, capacitance and resistance analyzer. The results demonstrated that the TiO 2 –WO 3 sample with a ratio of 1:1 showed better humidity sensing properties. Compared to previous studies, the prepared sensor exhibited higher sensitivity (S = 451) and the lower hysteresis value was around 0.13% at 32% RH. Complex impedance analysis indicated that the enhanced humidity sensitivity was probably due to spherical Brunauer–Emmett–Teller surface area and the hetero-junction between TiO 2 –WO 3 thin films, while the impedance varied about three orders of magnitude. Our results demonstrated the potential application of TiO 2 –WO 3 composite for fabricating high performance humidity sensors

  9. Humidity sensing properties of WO3 thick film resistor prepared by screen printing technique

    International Nuclear Information System (INIS)

    Garde, Arun S

    2014-01-01

    Highlights: • Polycrystalline WO 3 Thick films are fabricated by screen printing technique. • Monoclinic phases were the majority in formation of films. • The peak at 1643 cm −1 shows stretching vibrations attributed to W-OH of adsorbed H 2 O. • Absorption peaks in the range 879–650 cm −1 are attributed to the stretching W-O-W bonds. • Increase in resistance with decrease in RH when exposed to 20–100% RH. - Abstract: Thick films of tungsten oxide based were prepared using standard screen printing technique. To study the effect of temperature on the thick films were fired at different temperature for 30 min in air atmosphere. The WO 3 thick films were characterized with X-ray diffraction, scanning electron microscopy and EDAX for elemental analysis. The formation of mixed phases of the film together with majority of monoclinic phase was observed. IR spectra confirm the peak at 1643 cm −1 clearly shows stretching vibrations attributed to the W-OH bending vibration mode of the adsorbed water molecules. The absorption peaks in the range 879–650 cm −1 are attributed to the stretching W-O-W bonds (i.e. ν [W-O inter -W]). The peak located at 983 cm −1 belong to W=O terminal of cluster boundaries. A change in the resistance was observed with respect to the relative humidity when the WO 3 thick films were exposed to a wide humidity range of 20–100%. An increasing firing temperature of WO 3 film increases with the sensitivity. The parameters such as sensitivity and hysteresis of the WO 3 film sensors have been evaluated

  10. Exploration on anion ordering, optical properties and electronic structure in K3WO3F3 elpasolite

    International Nuclear Information System (INIS)

    Atuchin, V.V.; Isaenko, L.I.; Kesler, V.G.; Lin, Z.S.; Molokeev, M.S.; Yelisseyev, A.P.; Zhurkov, S.A.

    2012-01-01

    Room-temperature modification of potassium oxyfluorotungstate, G2-K 3 WO 3 F 3 , has been prepared by low-temperature chemical route and single crystal growth. Wide optical transparency range of 0.3–9.4 μm and forbidden band gap E g =4.32 eV have been obtained for G2-K 3 WO 3 F 3 crystal. Meanwhile, its electronic structure has been calculated with the first-principles calculations. The good agreement between the theorectical and experimental results have been achieved. Furthermore, G2-K 3 WO 3 F 3 is predicted to possess the relatively large nonlinear optical coefficients. - Graphical abstract: Using the cm-size K 3 WO 3 F 3 crystal (left upper), the transmission spectrum (right upper) and XPS valence electronic states (left lower) were measured, agreed with the ab initio results (right lower). Highlights: ► The cm-size G2-K 3 WO 3 F 3 single crystals are obtained. ► Optical absorption edge and transmission range are defined for G2-K 3 WO 3 F 3 crystal. ► Crystal structures of all known K 3 WO 3 F 3 polymorph modifications are determined. ► Experimental electronic structure is consistent with the first-principles result. ► G2-K 3 WO 3 F 3 is predicted as a crystal with large NLO coefficients.

  11. Polymorphism of tungsten perovskite compounds Ba/sub 2/SEsub(0. 67)WO/sub 6/

    Energy Technology Data Exchange (ETDEWEB)

    Schittenhelm, H J; Kemmler-Sack, S [Tuebingen Univ. (F.R. Germany). Inst. fuer Anorganische Chemie

    1976-09-01

    The compounds Ba/sub 2/SEsub(0.67)WO/sub 6/ with SE = Gd-Lu are polymorphic. Above 1200/sup 0/C the instable cubic modification (ordered perovskite with 4 formula units Ba/sub 2/SEsub(0.67)vacantsub(0.33)WO/sub 6/ per cell) transforms irreversibly into a hexagonal modification with completely filled cationic lattice. For Ba/sub 2/Eusub(0.67)WO/sub 6/ the transformation is incomplete. With SE = Nd and Sm only the cubic modification is formed.

  12. Synthesis and Visible-Light Photocatalytic Property of Bi2WO6Hierarchical Octahedron-Like Structures

    Directory of Open Access Journals (Sweden)

    Li Yuanyuan

    2008-01-01

    Full Text Available Abstract A novel octahedron-like hierarchical structure of Bi2WO6has been fabricated by a facile hydrothermal method in high quantity. XRD, SEM, TEM, and HRTEM were used to characterize the product. The results indicated that this kind of Bi2WO6crystals had an average size of ~4 μm, constructed by quasi-square single-crystal nanosheets assembled in a special fashion. The formation of octahedron-like hierarchical structure of Bi2WO6depended crucially on the pH value of the precursor suspensions. The photocatalytic activity of the hierarchical Bi2WO6structures toward RhB degradation under visible light was investigated, and it was found to be significantly better than that of the sample fabricated by SSR. The better photocatalytic property should be strongly associated with the high specific surface area and the abundant pore structure of the hierarchical octahedron-like Bi2WO6.

  13. Scintillation properties of pure and Ca-doped ZnWO4 crystals

    International Nuclear Information System (INIS)

    Danevich, F.A.; Shkulkova, O.G.; Henry, S.; Kraus, H.; McGowan, R.; Mikhailik, V.B.; Telfer, J.

    2008-01-01

    Following the investigations of the structure and scintillation properties of Ca-doped zinc tungstate powder [phys. stat. sol. (a) 204, 730 (2007)] a single-crystal of ZnWO 4 -Ca (0.5 mol%) was grown and characterised. The relative light output, energy resolution and decay characteristics were measured for pure and Ca-doped ZnWO 4 scintillators. An increase in the light yield of ∝40% compared with the undoped crystal, and an energy resolution 9.6% ( 137 Cs) were obtained for Ca-doped ZnWO 4 . The observed improvement is attributed to the reduction of self-absorption (bleaching) of the crystal. The cause of bleaching as well as the possible contribution of scattering is discussed. (copyright 2008 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

  14. Fabrication and photocatalysis of mesoporous ZnWO4 with PAMAM as a template

    International Nuclear Information System (INIS)

    Lin Shen; Chen Jiebo; Weng Xiulan; Yang Liuyi; Chen Xinqin

    2009-01-01

    Mesoporous ZnWO 4 was prepared with the template of PAMAM. The as-formed samples were characterized by X-ray diffraction (XRD), nitrogen absorption, scanning electron microscopy (SEM), transmission electron microscopy (TEM), and UV-vis diffuse reflectance spectroscopy (DRS). It is found that the size of pore is in the range of 5-22 nm and that the porosity of ZnWO 4 is composed of aggregated ZnWO 4 nanoparticles. The photocatalytic activities towards degradation of rhodamine B (RhB) and malachite green (MG) under UV light has been investigated. The formation mechanism of mesoporous structures is proposed

  15. Ultrathin percolated WO{sub 3} cluster film and its resistive response to H{sub 2}

    Energy Technology Data Exchange (ETDEWEB)

    Zhao, Meng [Research Center for Solid State Physics and Materials, School of Mathematics and Physics, Suzhou University of Science and Technology, Suzhou 215009 (China); Department of Applied Physics and Materials Research Center, The Hong Kong Polytechnic University, Hung Hom, Kowloon, Hong Kong (China); Wong, Man Hon; Huang, Jian Xing [Department of Applied Physics and Materials Research Center, The Hong Kong Polytechnic University, Hung Hom, Kowloon, Hong Kong (China); Ong, Chung Wo, E-mail: c.w.ong@polyu.edu.hk [Department of Applied Physics and Materials Research Center, The Hong Kong Polytechnic University, Hung Hom, Kowloon, Hong Kong (China)

    2014-11-05

    Highlights: • Ultrathin percolated network of WO{sub 3} clusters was fabricated. • The WO{sub 3} clusters are modeled by spherical caps connected by ultrafine linkages. • The ultrathin percolated network of WO{sub 3} clusters shows fast response rate to H{sub 2}. • The fast response is attributed to the rapid electrical switching of the linkages. • Improved H{sub 2} sensing properties may be achieved if narrower linkages are used. - Abstract: Thin films composed of tungsten oxide (WO{sub 3}) nanoclusters were fabricated by oxidizing supersonic cluster beam deposited tungsten films at various temperatures. Oxidation at 700 °C resulted in aggregation of the deposits, forming a percolated network of WO{sub 3} spherical caps connected by fine links. The resistance response of the palladium-(Pd-) coated film sample to hydrogen (H{sub 2}) was investigated. The response rate was faster than those of other samples oxidized at lower temperatures. This is the result of the rapid electrical switching of the intercluster links between the highly resistive depleted state and conducting hydrogenated state. The possibility of improving the H{sub 2} sensing response rate with the use of the percolated WO{sub 3} film structure is illustrated.

  16. Study of phase equilibria and glass formation in the CaO-WO3-P2O5 system

    International Nuclear Information System (INIS)

    Bielis, I.Ya.

    1980-01-01

    The method of quenching has been used to investigate the liquidus surface of a portion of the CaO-WO 3 -P 2 O 5 system limited by the Ca(PO 3 ) 2 -W 2 O 3 (PO 4 ) 2 and CaWO 4 -Ca 2 P 2 O 7 cross-sections. The primary crystallization fields on the compounds: WO 3 , W 2 O 3 (PO 4 ) 2 , CaWO 4 , Ca 2 P 7 O 7 , Ca(PO 3 ) 2 are separated. The liquidus surface isotherms at 900, 1000, 1100 and 1200 deg C have been plotted on the concentration triangle plane. It has been found that the cross-sections of W 2 O 3 (PO 4 ) 2 -Ca(PO 3 ) 2 , WO 3 -Ca(PO 3 ) 2 , WO 3 -Ca 2 P 2 O 7 and CaWO 4 -Ca 2 P 2 O 7 are eutectic-type quasi-binary systems. The position of the glass transition region in the CaO-WO 3 -P 2 O 5 system has been determined for the treatment temperatures of 1100, 1200 and 1300 deg C and a correlation between the configuration of the glass transition region and the phase diagram of the system has been demonstrated [ru

  17. Investigation of the La2O3-Nb2O5-WO3 ternary phase diagram: Isolation and crystal structure determination of the original La3NbWO10 material

    KAUST Repository

    Vu, T.D.; Vu, T.D.; Barre, M.; Adil, Karim; Jouanneaux, A.; Suard, E.; Goutenoire, F.

    2015-01-01

    In the course of the exploration of the La2O3-WO3-Nb2O5 ternary phase diagram, a new compound with the formula La3NbWO10 was discovered. Its structure was determined from a combination of powder X-ray and neutron diffraction data. It crystallizes

  18. High-pressure phases in the system W-O. Pt. 2

    International Nuclear Information System (INIS)

    Barabanenkov, Yu.A.; Zakharov, N.D.; Zibrov, I.P.; Filonenko, V.P.; Werner, P.; Popov, A.I.; Valkovskii, M.D.

    1993-01-01

    A new type of tungsten oxide has been synthesized from a mixture of W and WO 3 by a solid-phase sintering method under high-pressure conditions. The crystal structure of the new oxide was investigated by HRTEM, selected-area electron diffraction and X-ray powder diffraction. The structure belongs to space group Pbam or P2 1 2 1 2 and has the following unit-cell parameters: a=21.431(9), b=17.766(7), c=3.783(2) A, V=1440 A 3 , Z=32, D x =8.33 g cm -3 . The structural model and W-cation positions were determined by HRTEM and image processing. X-ray powder analysis and the SHELX computer program were used to prove the proposed structural model: N=158, R=0.075, U iso (W)=0.019(3), U iso (O)=0.055(12) A 2 . The investigated crystal structure is, in fact, similar to WO 2.72 and is formed by W-O octahedra and pentagonal bipyramids. (orig.)

  19. Preparation of tungsten coatings on graphite by electro-deposition via Na{sub 2}WO{sub 4}–WO{sub 3} molten salt system

    Energy Technology Data Exchange (ETDEWEB)

    Sun, Ning-bo [School of Materials Science and Engineering, University of Science and Technology Beijing, 30 Xueyuan Road, Haidian District, Beijing 100083 (China); Zhang, Ying-chun, E-mail: zycustb@163.com [School of Materials Science and Engineering, University of Science and Technology Beijing, 30 Xueyuan Road, Haidian District, Beijing 100083 (China); Jiang, Fan; Lang, Shao-ting [School of Materials Science and Engineering, University of Science and Technology Beijing, 30 Xueyuan Road, Haidian District, Beijing 100083 (China); Xia, Min [School of Materials Science and Engineering, University of Science and Technology Beijing, 30 Xueyuan Road, Haidian District, Beijing 100083 (China); Institute of Powder Metallurgy and Advanced Ceramics, Southwest Jiaotong University, 111, 1st Section, Northern 2nd Ring Road, Chengdu (China)

    2014-11-15

    Highlights: • Tungsten coatings on graphite were firstly obtained by electro-deposition method via Na{sub 2}WO{sub 4}–WO{sub 3} molten salt system. • Uniform and dense tungsten coatings could be easily prepared in each face of the sample, especially the complex components. • The obtained tungsten coatings are with high purity, ultra-low oxygen content (about 0.022 wt%). • Modulate pulse parameters can get tungsten coatings with different thickness and hardness. - Abstract: Tungsten coating on graphite substrate is one of the most promising candidate materials as the ITER plasma facing components. In this paper, tungsten coatings on graphite substrates were fabricated by electro-deposition from Na{sub 2}WO{sub 4}–WO{sub 3} molten salt system at 1173 K in atmosphere. Tungsten coatings with no impurities were successfully deposited on graphite substrates under various pulsed current densities in an hour. By increasing the current density from 60 mA cm{sup −2} to 120 mA cm{sup −2} an increase of the average size of tungsten grains, the thickness and the hardness of tungsten coatings occurs. The average size of tungsten grains can reach 7.13 μm, the thickness of tungsten coating was in the range of 28.8–51 μm, and the hardness of coating was higher than 400 HV. No cracks or voids were observed between tungsten coating and graphite substrate. The oxygen content of tungsten coating is about 0.022 wt%.

  20. Synthesis and photoluminescence properties of Sm3+-doped CaWO4 nanoparticles

    International Nuclear Information System (INIS)

    Xiao Qi; Zhou Qitao; Li Ming

    2010-01-01

    The Sm 3+ -doped CaWO 4 nanoparticles were synthesized by hydrothermal method. The room temperature photoluminescence (PL) spectra of Sm 3+ -doped CaWO 4 nanoparticles doped with different Sm 3+ concentrations under 405 nm excitation have been investigated. The PL spectra showed four strong emission peaks at 460, 571, 609, and 653 nm. The first emission peak at 460 nm could be due to a structural defect of the lattice, an oxygen-deficient WO 3 complex. The other three emissions at 571, 609, and 653 nm were due to the f-f forbidden transitions of the 4f electrons of Sm 3+ , corresponding to 4 G 5/2 → 6 H 5/2 (571 nm), 6 H 7/2 (609 nm), and 6 H 9/2 (653 nm), respectively. In addition, the optimum Sm 3+ concentration in CaWO 4 nanoparticles for optical emission was determined to be 1.0%. The Sm 3+4 G 5/2 → 6 H 7/2 (609 nm) emission intensity of Sm 3+ -doped CaWO 4 nanoparticles significantly increased with the increase of Sm 3+ concentration, and showed a maximum when Sm 3+ doping content was 1.0%. If Sm 3+ concentration continued to increase, namely more than 1.0%, the Sm 3+4 G 5/2 → 6 H 7/2 emission intensity would decrease. The present materials might be a promising phosphor for white-light LED applications.

  1. Production of CaWO{sub 4} crystals for direct dark matter search with CRESST

    Energy Technology Data Exchange (ETDEWEB)

    Muenster, Andrea [Physik-Department and Excellence Cluster Universe, Technische Universitaet Muenchen, D-85748 Garching (Germany); Collaboration: CRESST-Collaboration

    2016-07-01

    The direct dark matter search experiment CRESST (Cryogenic Rare Event Search with Superconducting Thermometers) uses scintillating CaWO{sub 4} single crystals as targets for possible recoils of dark matter particles. Since several years these CaWO{sub 4} crystals are produced directly at the Technische Universitaet Muenchen (TUM) including the CaWO{sub 4} powder production from the raw materials CaCO{sub 3} and WO{sub 3}, the CaWO{sub 4} crystal growth via the Czochralski method as well as the after-growth treatment of the crystals. In the recently finished CRESST-II Phase 2 (2013-2015), 4 TUM-grown crystals were installed in the main cryostat for the first time. Showing one of the best radiopurities of all installed crystals combined with an excellent detector performance the analysis of the crystal TUM40 resulted in the best sensitivity for low-mass dark matter particles in 2014. For the upcoming CRESST-III phase 2 we aim for a further improvement in radiopurity by a factor of 100. First results of a chemical purification of the raw materials as well as future plans to reduce the intrinsic background via recrystallization are presented.

  2. Characteristics of W/O emulsions containing polymeric emulsifier PEG 30-dipolyhydroxystearate

    Directory of Open Access Journals (Sweden)

    Milinković Jelena R.

    2016-01-01

    Full Text Available Water-in-oil (W/O emulsions are dispersed systems which are often used in the pharmaceutical, cosmetic and food industries as products, or as carriers of active substances. It is well known that they are very unstable, so that selection of the emulsifier and properties of the oil and water phase are main factors affecting their stability. The aim of this paper was to examine the possibility of application of a lipophilic, polymeric emulsifier, PEG 30-dipolyhydroxystearate (CithrolTM DPHS, for stabilization of W/O emulsions. Behaviour of the emulsifier at W/O interfaces was determined by means of tensiometry. A series of emulsions were prepared with 20% (w/w of water and different types of oil. Droplet size, droplet size distribution, viscosity, and sedimentation stability during 30 days of storage at room temperature of the emulsions prepared with paraffin oil, olive oil, grape seed oil, and medium-chain triglycerides, stabilized with 1% CithrolTM DPHS, were determined. All investigated emulsions were stable for 30 days, except the one prepared with paraffin oil. The results of this study confirmed that PEG 30-dipolyhydroxylstearate is a good emulsifier and stabilizer of W/O emulsions which contain different types of oil. [Projekat Ministarstva nauke Republike Srbije, br. III46010

  3. Characterization of Porous WO3 Electrochromic Device by Electrochemical Impedance Spectroscopy

    Directory of Open Access Journals (Sweden)

    Chien Chon Chen

    2013-01-01

    Full Text Available This paper concerns the microstructure of the anodic tungsten oxide (WO3 and its use in an electrochromic (EC glass device. When voltages between 100 V and 160 V were applied to tungsten film for 1 h under 0.4 wt. % NaF electrolyte, porous WO3 film was formed. The film, which had a large surface area, was used as electrochromic film for EC glass. The average transmittance in a visible region of the spectrum for a 144 cm2 EC device was above 75% in the bleached state and below 40% in the colored state, respectively. Repeatability using of the colored/bleached cycles was tested good by a cyclic voltammograms method. The internal impedance values under colored and bleached states were detected and simulated using an electrical impedance spectra (EIS technique. The EC glass impedance characteristics were simulated using resistors, capacitors, and Warburg impedance. The ITO/WO3, WO3/electrolyte, electrolyte/NiO, and NiO/ITO interfaces can be simulated using a resistance capacitance (RC parallel circuits, and bulk materials such as the indium tin oxide (ITO and conducting wire can be simulated by using a series of resisters.

  4. Tailored temperature window of CuO{sub x}/WO{sub x}–ZrO{sub 2} for NO{sub x} reduction via adjusting the calcination temperature of WO{sub x}–ZrO{sub 2}

    Energy Technology Data Exchange (ETDEWEB)

    Si, Zhichun, E-mail: si.zhichun@sz.tsinghua.edu.cn [Advanced Materials Institute, Graduate School at Shenzhen, Tsinghua University, Shenzhen 518055 (China); Wu, Xiaodong [State Key Laboratory of New Ceramics and Fine Process, Department of Materials Science and Engineering, Tsinghua University, Beijing 100084 (China); Yangtze Delta Region Institute of Tsinghua University, Zhejiang 314000 (China); Weng, Duan, E-mail: duanweng@tsinghua.edu.cn [State Key Laboratory of New Ceramics and Fine Process, Department of Materials Science and Engineering, Tsinghua University, Beijing 100084 (China); Ma, Ziran; Ma, Jing [State Key Laboratory of New Ceramics and Fine Process, Department of Materials Science and Engineering, Tsinghua University, Beijing 100084 (China)

    2013-02-15

    WO{sub x}–ZrO{sub 2} support was calcined at various temperatures for obtaining controllable activity of copper catalysts for NO{sub x} reduction by ammonia. The temperature window of copper catalyst for over 80% NO{sub x} conversion shifts from 180–300 to 230–350 °C by elevating the calcination temperature of WO{sub x}–ZrO{sub 2} support from 500 to 600 °C, due to the increased Brønsted acidity and reduced structure and electronic interactions between copper oxides and tungsten oxides arising from the polymerization of WO{sub x} clusters on surface of support. Calcining WO{sub x}–ZrO{sub 2} support at 700 °C leads to the reduced redox property of copper oxides on the Cu–O–W interface and the formation of bulk-like CuO, results in a low activity of catalyst. - Graphical abstract: The temperature window of catalyst for over 80% NO{sub x} conversion shifts from 180-300 °C to 230–350 °C by elevating the calcination temperature of WO{sub x}–ZrO{sub 2} support from 500 °C to 600 °C. Highlights: ► The temperature window of catalyst is tailored by calcining the support. ► The mechanisms of tailoring the temperature window of catalyst are discussed. ► The polymerization of WO{sub x} leads to the increased Brønsted acidity of catalysts. ► The CuO{sub x}/WO{sub x} interactions are reduced by elevating calcination temperature of support.

  5. Synthesis and Characterization of WO3/Graphene Nanocomposites for Enhanced Photocatalytic Activities by One-Step In-Situ Hydrothermal Reaction

    Directory of Open Access Journals (Sweden)

    Xiaoxiao Hu

    2018-01-01

    Full Text Available Tungsten trioxide (WO3 nanorods are synthesized on the surface of graphene (GR sheets by using a one-step in-situ hydrothermal method employing sodium tungstate (Na2WO4·2H2O and graphene oxide (GO as precursors. The resulting WO3/GR nanocomposites are characterized by X-ray diffraction, Raman spectroscopy, transmission electron microscopy, scanning electron microscopy and X-ray photoelectron spectroscopy. The results confirm that the interface between WO3 nanorod and graphene contains chemical bonds. The enhanced optical absorption properties are measured by UV-vis diffuse reflectance spectra. The photocatalytic activity of the WO3/GR nanocomposites under visible light is evaluated by the photodegradation of methylene blue, where the degradation rate of WO3/GR nanocomposites is shown to be double that of pure WO3. This is attributed to the synergistic effect of graphene and the WO3 nanorod, which greatly enhances the photocatalytic performance of the prepared sample, reduces the recombination of the photogenerated electron-hole pairs and increases the visible light absorption efficiency. Finally, the photocatalytic mechanism of the WO3/GR nanocomposites is presented. The synthesis of the prepared sample is convenient, direct and environmentally friendly. The study reports a highly efficient composite photocatalyst for the degradation of contaminants that can be applied to cleaning up the environment.

  6. Radiation-induced color centers in La-doped PbWO sub 4 crystals

    CERN Document Server

    Deng, Q; Zhu, R Y

    1999-01-01

    This report presents the result of a study on radiation-induced color center densities in La-doped lead tungstate (PbWO sub 4) crystals. The creation and annihilation constants of radiation-induced color centers were determined by using transmittance data measured for a PbWO sub 4 sample before and during sup 6 sup 0 Co gamma-ray irradiation at a dose rate of 15 rad/h. Following a model of color center kinetics, these constants were used to calculate color center densities under irradiations at 100 rad/h. The result was found to be in good agreement with experimental data, indicating that the behaviour of PbWO sub 4 crystals under irradiation can be predicted according to this model.

  7. WO3 and W Thermal Atomic Layer Etching Using "Conversion-Fluorination" and "Oxidation-Conversion-Fluorination" Mechanisms.

    Science.gov (United States)

    Johnson, Nicholas R; George, Steven M

    2017-10-04

    The thermal atomic layer etching (ALE) of WO 3 and W was demonstrated with new "conversion-fluorination" and "oxidation-conversion-fluorination" etching mechanisms. Both of these mechanisms are based on sequential, self-limiting reactions. WO 3 ALE was achieved by a "conversion-fluorination" mechanism using an AB exposure sequence with boron trichloride (BCl 3 ) and hydrogen fluoride (HF). BCl 3 converts the WO 3 surface to a B 2 O 3 layer while forming volatile WO x Cl y products. Subsequently, HF spontaneously etches the B 2 O 3 layer producing volatile BF 3 and H 2 O products. In situ spectroscopic ellipsometry (SE) studies determined that the BCl 3 and HF reactions were self-limiting versus exposure. The WO 3 ALE etch rates increased with temperature from 0.55 Å/cycle at 128 °C to 4.19 Å/cycle at 207 °C. W served as an etch stop because BCl 3 and HF could not etch the underlying W film. W ALE was performed using a three-step "oxidation-conversion-fluorination" mechanism. In this ABC exposure sequence, the W surface is first oxidized to a WO 3 layer using O 2 /O 3 . Subsequently, the WO 3 layer is etched with BCl 3 and HF. SE could simultaneously monitor the W and WO 3 thicknesses and conversion of W to WO 3 . SE measurements showed that the W film thickness decreased linearly with number of ABC reaction cycles. W ALE was shown to be self-limiting with respect to each reaction in the ABC process. The etch rate for W ALE was ∼2.5 Å/cycle at 207 °C. An oxide thickness of ∼20 Å remained after W ALE, but could be removed by sequential BCl 3 and HF exposures without affecting the W layer. These new etching mechanisms will enable the thermal ALE of a variety of additional metal materials including those that have volatile metal fluorides.

  8. Optical spectroscopy of rare-earth ions doped KY(WO4)2 thin films

    NARCIS (Netherlands)

    García-Revilla, S.; Valiente, R.; Romanyuk, Y.E.; Utke, I.; Pollnau, Markus

    KY(WO4)2 thin films doped with Dy3+, Tb3+, Yb3+, were grown onto KY(WO4)2 substrates using liquid-phase epitaxy. Spectroscopic investigations of the grown layers were performed. Obtained results were compared with spectra given for bulk crystals. Upconversion experiments after direct Yb3+ excitation

  9. Electronic and optical properties of nanocrystalline WO3 thin films studied by optical spectroscopy and density functional calculations

    International Nuclear Information System (INIS)

    Johansson, Malin B; Niklasson, Gunnar A; Österlund, Lars; Baldissera, Gustavo; Persson, Clas; Valyukh, Iryna; Arwin, Hans

    2013-01-01

    The optical and electronic properties of nanocrystalline WO 3 thin films prepared by reactive dc magnetron sputtering at different total pressures (P tot ) were studied by optical spectroscopy and density functional theory (DFT) calculations. Monoclinic films prepared at low P tot show absorption in the near infrared due to polarons, which is attributed to a strained film structure. Analysis of the optical data yields band-gap energies E g ≈ 3.1 eV, which increase with increasing P tot by 0.1 eV, and correlate with the structural modifications of the films. The electronic structures of triclinic δ-WO 3 , and monoclinic γ- and ε-WO 3 were calculated using the Green function with screened Coulomb interaction (GW approach), and the local density approximation. The δ-WO 3 and γ-WO 3 phases are found to have very similar electronic properties, with weak dispersion of the valence and conduction bands, consistent with a direct band-gap. Analysis of the joint density of states shows that the optical absorption around the band edge is composed of contributions from forbidden transitions (>3 eV) and allowed transitions (>3.8 eV). The calculations show that E g in ε-WO 3 is higher than in the δ-WO 3 and γ-WO 3 phases, which provides an explanation for the P tot dependence of the optical data. (paper)

  10. Electronic and optical properties of nanocrystalline WO3 thin films studied by optical spectroscopy and density functional calculations

    Science.gov (United States)

    Johansson, Malin B.; Baldissera, Gustavo; Valyukh, Iryna; Persson, Clas; Arwin, Hans; Niklasson, Gunnar A.; Österlund, Lars

    2013-05-01

    The optical and electronic properties of nanocrystalline WO3 thin films prepared by reactive dc magnetron sputtering at different total pressures (Ptot) were studied by optical spectroscopy and density functional theory (DFT) calculations. Monoclinic films prepared at low Ptot show absorption in the near infrared due to polarons, which is attributed to a strained film structure. Analysis of the optical data yields band-gap energies Eg ≈ 3.1 eV, which increase with increasing Ptot by 0.1 eV, and correlate with the structural modifications of the films. The electronic structures of triclinic δ-WO3, and monoclinic γ- and ε-WO3 were calculated using the Green function with screened Coulomb interaction (GW approach), and the local density approximation. The δ-WO3 and γ-WO3 phases are found to have very similar electronic properties, with weak dispersion of the valence and conduction bands, consistent with a direct band-gap. Analysis of the joint density of states shows that the optical absorption around the band edge is composed of contributions from forbidden transitions (>3 eV) and allowed transitions (>3.8 eV). The calculations show that Eg in ε-WO3 is higher than in the δ-WO3 and γ-WO3 phases, which provides an explanation for the Ptot dependence of the optical data.

  11. Hydrothermal deposition and photochromic performances of three kinds of hierarchical structure arrays of WO3 thin films

    International Nuclear Information System (INIS)

    Ding, Defang; Shen, Yi; Ouyang, Yali; Li, Zhen

    2012-01-01

    Three kinds of tungsten oxide (WO 3 ) thin films have been fabricated by a simple hydrothermal deposition method. Scanning electron microscopy images of the products revealed that the capping agents did impact the microstructure of WO 3 films. Films prepared without capping agents were ordered nanorod arrays, while the ones obtained with ethanol and oxalic acid revealed peeled-orange-like and cauliflower-like hierarchical structure arrays, respectively. Both of the two hierarchical structures were composed of much thinner nanorods compared with the one obtained without capping agents. All the WO 3 films exhibited good photochromic properties and the two with inducers performed even better, which could be due to the changes in the microstructure that increased the amount of photogenerated electron–hole pairs and the proton diffusion rates. - Highlights: ► Ordered WO 3 nanorod arrays were prepared by hydrothermal deposition process. ► Two hierarchical WO 3 structure arrays were obtained with ethanol and oxalic acid. ► Mechanism for the improved photochromic performances of WO 3 films is proposed.

  12. Study of photocatalytic activities of Bi{sub 2}WO{sub 6} nanoparticles synthesized by fast microwave-assisted method

    Energy Technology Data Exchange (ETDEWEB)

    Phu, Nguyen Dang [Faculty of Physics, Hanoi National University of Education, 136 Xuanthuy, Cau Giay, Hanoi (Viet Nam); Hoang, Luc Huy, E-mail: hoanglhsp@hnue.edu.vn [Faculty of Physics, Hanoi National University of Education, 136 Xuanthuy, Cau Giay, Hanoi (Viet Nam); Chen, Xiang-Bai, E-mail: xchen@wit.edu.cn [School of Science and Laboratory of Optical Information Technology, Wuhan Institute of Technology, Wuhan 430205 (China); Kong, Meng-Hong [School of Science and Laboratory of Optical Information Technology, Wuhan Institute of Technology, Wuhan 430205 (China); Wen, Hua-Chiang; Chou, Wu Ching [Department of Electrophysics, National Chiao Tung University, Hsin-Chu 30010, Taiwan (China)

    2015-10-25

    We present a study of photocatalytic activities of Bi{sub 2}WO{sub 6} nanoparticles synthesized by fast microwave-assisted method. The photocatalytic activities of the nanoparticles were evaluated by the decolorization of methylene-blue under visible-light-irradiation. Our results show that the surface area of Bi{sub 2}WO{sub 6} nanoparticles plays a major role for improving photocatalytic activity, while visible-light absorption has only a weak effect on photocatalytic activity. This suggests efficient transportation of photo-generated electrons and holes to the oxidation active sites on the surface of nanoparticles, indicating Bi{sub 2}WO{sub 6} nanoparticles synthesized by fast microwave-assisted method are promising for achieving high photocatalytic activity under visible-light-irradiation. - Highlights: • The Bi{sub 2}WO{sub 6} nanoparticles were synthesized via fast microwave-assisted method. • The obtained Bi{sub 2}WO{sub 6} nanoparticles exhibited visible-light absorbance. • The surface area of Bi{sub 2}WO{sub 6} nanoparticles plays major role for improving photocatalytic activity. • The Bi{sub 2}WO{sub 6} nanoparticles are promising for achieving high photocatalytic activity under visible-light-irradiation.

  13. Hydrothermal synthesis of hierarchical WO3 nanostructures for dye-sensitized solar cells

    International Nuclear Information System (INIS)

    Rashad, M.M.; Shalan, A.E.

    2014-01-01

    Hierarchical architectures consisting of one-dimensional (1D) nanostructures are of great interest for potential use in energy and environmental applications in recent years. In this work, hierarchical tungsten oxide (WO 3 ) has been synthesized via a facile hydrothermal route from ammonium metatungstate hydrate and implemented as photoelectrode for dye-sensitized solar cells. The urchin-like WO 3 micro-patterns are constructed by self-organized nanoscale length 1D building blocks, which are single crystalline in nature, grown along (001) direction and confirm an orthorhombic crystal phase. The obtained powders were investigated by XRD, SEM, TEM and UV-Vis Spectroscopy. The photovoltaic performance of dye-sensitized solar cells based on WO 3 photoanodes was investigated. With increasing the calcination temperature of the prepared nanopowders, the light-electricity conversion efficiency (η) was increased. The results were attributed to increase the crystallinity of the particles and ease of electron movement. The DSSC based on hierarchical WO 3 showed a short-circuit current, an open-circuit voltage, a fill factor, and a conversion efficiency of 4.241 mA/cm 2 , 0.656 V, 66.74, and 1.85 %, respectively. (orig.)

  14. Structural phototransformation of WO{sub 3} thin films detected by photoacoustic analysis

    Energy Technology Data Exchange (ETDEWEB)

    Pacheco, Argelia Perez, E-mail: ekargy@hotmail.com [Universidad Nacional Autonoma de Mexico, Laboratorio de Fotofisica y Peliculas Delgadas-CCADET, Ciudad Universitaria, Coyoacan, A.P. 70-186, C.P. 04510, Mexico, D.F. (Mexico); Montes de Oca, C. Oliva; Castaneda-Guzman, R.; Garcia, A. Esparza [Universidad Nacional Autonoma de Mexico, Laboratorio de Fotofisica y Peliculas Delgadas-CCADET, Ciudad Universitaria, Coyoacan, A.P. 70-186, C.P. 04510, Mexico, D.F. (Mexico)

    2012-11-15

    Highlights: Black-Right-Pointing-Pointer The phototransformation of WO{sub 3} thin films were studied by photoacoustic technique. Black-Right-Pointing-Pointer The phase transition in WO{sub 3} thin films was induced by laser irradiation fluence. Black-Right-Pointing-Pointer The onset and end of the phototransformation in the thin films was identified. Black-Right-Pointing-Pointer The ablation threshold for each sample was identified. - Abstract: The photoacoustic technique (PA) was used to detect the phase transformation from amorphous to crystalline state of tungsten oxide (WO{sub 3}) thin films induced by UV pulsed laser radiation at low energy (<1.5 mJ). The evolution of photoacoustic signal was studied by a correlation analysis, comparing successive signals at fluences ranging from 0 to 20 mJ/cm{sup 2}. In this interval, it was possible to observe structural changes and the ablation threshold in films due to incident laser fluence effect. Thin films of WO{sub 3} were deposited by DC reactive magnetron sputtering over glass substrates at different deposition times. The results obtained by correlation analysis were compared with Raman spectroscopy data.

  15. Electrodeposition of WO3 nanoparticles into surface mounted metal-organic framework HKUST-1 thin films

    Science.gov (United States)

    Yoo, Hyeonseok; Welle, Alexander; Guo, Wei; Choi, Jinsub; Redel, Engelbert

    2017-03-01

    We describe a novel procedure to fabricate WO3@surface-mounted metal-organic framework (SURMOF) hybrid materials by electrodeposition of WO3 nanoparticles into HKUST-1, also termed Cu3(BTC)2 SURMOFs. These materials have been characterized using x-ray diffraction, time-of-flight secondary ion mass spectrometry, scanning electron microscopy, x-ray photoelectron spectroscopy as well as linear sweep voltammetry. The WO3 semiconductor/SURMOF heterostructures were further tested as hybrid electrodes in their performance for hydrogen evolution reaction from water.

  16. Synthesis of WO3 nanoparticles by citric acid-assisted precipitation and evaluation of their photocatalytic properties

    International Nuclear Information System (INIS)

    Sánchez-Martínez, D.; Martínez-de la Cruz, A.; López-Cuéllar, E.

    2013-01-01

    Graphical abstract: Display Omitted Highlights: ► WO 3 nanoparticles were synthesized by a simple citric acid-assisted precipitation. ► WO 3 photocatalyst was able to the partial mineralization of rhB, IC and MO. ► WO 3 can be considered as a photocatalyst active under visible light irradiation. -- Abstract: WO 3 nanoparticles were synthesized by citric acid-assisted precipitation method using a 1:1.5 molar ratio of ammonium paratungstate hydrate (H 42 N 10 O 42 W 12 ·xH 2 O):citric acid (C 6 H 8 O 7 ). The formation of monoclinic crystal structure of WO 3 at different temperatures was confirmed by X-ray powder diffraction (XRD). The characterization of the samples synthesized was complemented by transmission electron microscopy (TEM), Brunauer–Emmitt–Teller surface area (BET) and diffuse reflectance spectroscopy (DRS). According to the thermal treatment followed during the synthesis of WO 3 , the morphology of the nanoparticles formed was characterized by rectangular and ovoid shapes. The photocatalytic activity of WO 3 obtained under different experimental conditions was evaluated in the degradation of rhodamine B (rhB), indigo carmine (IC), methyl orange (MO), and Congo red (CR) in aqueous solution under UV and UV–vis radiation. The highest photocatalytic activity was observed in the sample obtained by thermal treatment at 700 °C. In general, the sequence of degradation of the organic dyes was: indigo carmine (IC) > rhodamine B (rhB) > methyl orange (MO) > Congo red (CR). The mineralization degree of organic dyes by WO 3 photocatalysts was determined by total organic carbon analysis (TOC) reaching percentages of mineralization of 82% (rhB), 85% (IC), 28% (MO), and 7% (CR) for 96 h of lamp irradiation.

  17. Optical and electrochromic properties of Sn:WO3 cermets

    International Nuclear Information System (INIS)

    Ashrit, P.V.; Bader, G.; Girouard, F.E.; Truong, V.V.

    1989-01-01

    This paper discusses optical and electrochromic properties of Sn:WO 3 cermets deposited by alternate layer thermal deposition. These cermets exhibit electrical and optical behavior in the as deposited state. The inclusion of Sn in the WO 3 matrix enhances the Electrical conductivity of the system and renders them fairly transparent in the visible region. The electrochromic behavior of such systems is studied under both proton and Li + ion injection. The good conductivity and good transmission combined with good electrochromic characteristics of these systems indicate the possibility of utilizing this type of cermet for the dual role of transparent conductor (TC) and electrochromic (EC) layer

  18. Reduced graphene oxide wrapped Bi{sub 2}WO{sub 6} hybrid with ultrafast charge separation and improved photoelectrocatalytic performance

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Huan [School of Chemical Engineering and Technology, Hebei University of Technology, Tianjin 300130, PR China (China); Liang, Yinghua, E-mail: liangyh@ncst.edu.cn [School of Chemical Engineering and Technology, Hebei University of Technology, Tianjin 300130, PR China (China); College of Chemical Engineering, North China University of Science and Technology, Tangshan 063009, PR China (China); Liu, Li; Hu, Jinshan [College of Chemical Engineering, North China University of Science and Technology, Tangshan 063009, PR China (China); Cui, Wenquan, E-mail: wkcui@163.com [College of Chemical Engineering, North China University of Science and Technology, Tangshan 063009, PR China (China)

    2017-01-15

    Highlights: • The rGO wrapped Bi{sub 2}WO{sub 6} photoelectrode was successfully synthesized. • The Bi{sub 2}WO{sub 6}@rGOhighlyincreasedthechargeseparationefficiency. • The photoelectrode exhibited enhanced photoelectrocatalytic degradation for RhB. - Abstract: A reduced graphene oxide (rGO) wrapped Bi{sub 2}WO{sub 6} (Bi{sub 2}WO{sub 6}@rGO) hybrid as photoelectrode for enhanced photoelectrocatalytic (PEC) degradation of organic pollutants is reported, which exhibited excellent charge separation and photoconversion efficiency. The core@shell structured Bi{sub 2}WO{sub 6}@rGO photoelectrode yielded a pronounced 1.56-fold and 23.8-fold photocurrent density at 1.0 V vs. saturated calomel electrode (SCE), than that of loading structured Bi{sub 2}WO{sub 6}-rGO and pure Bi{sub 2}WO{sub 6}. The Bi{sub 2}WO{sub 6}@rGO hybrid exhibited enhanced photoelectrocatalytic efficiency for degradation of Rhodamine B (RhB), which was 43.0% and 65.6% higher than that of photocatalytic (PC) and electrocatalytic (EC) processes, respectively. The enhancement in PEC degradation of RhB benefited from: (1) a strong interaction and a wide range of conjugation were formed in the core@shell system; (2) a 0.26 V of flat band potential was negatively shifted in case of Bi{sub 2}WO{sub 6}@rGO composite; (3) the photogenerated electrons and holes could be spatially separated by external electric potentials.

  19. Role of indium tin oxide electrode on the microstructure of self-assembled WO3-BiVO4 hetero nanostructures

    Science.gov (United States)

    Song, Haili; Li, Chao; Van, Chien Nguyen; Dong, Wenxia; Qi, Ruijuan; Zhang, Yuanyuan; Huang, Rong; Chu, Ying-Hao; Duan, Chun-Gang

    2017-11-01

    Self-assembled WO3-BiVO4 nanostructured thin films were grown on a (001) yttrium stabilized zirconia (YSZ) substrate by the pulsed laser deposition method with and without the indium tin oxide (ITO) bottom electrode. Their microstructures including surface morphologies, crystalline phases, epitaxial relationships, interface structures, and composition distributions were investigated by scanning electron microscopy, high-resolution transmission electron microscopy, and X-ray energy dispersive spectroscopy. In both samples, WO3 formed nanopillars embedded into the monoclinic BiVO4 matrix with specific orientation relationships. In the sample with the ITO bottom electrode, an atomically sharp BiVO4/ITO interface was formed and the orthorhombic WO3 nanopillars were grown on a relaxed BiVO4 buffer layer with a mixed orthorhombic and hexagonal WO3 transition layer. In contrast, a thin amorphous layer appears at the interfaces between the thin film and the YSZ substrate in the sample without the ITO electrode. In addition, orthorhombic Bi2WO6 lamellar nanopillars were formed between WO3 and BiVO4 due to interdiffusion. Such a WO3-Bi2WO6-BiVO4 double heterojunction photoanode may promote the photo-generated charge separation and further improve the photoelectrochemical water splitting properties.

  20. Study on light output and energy resolution of PbWO4 crystal

    International Nuclear Information System (INIS)

    Su Guanghui; Yue Ke; Sun Zhiyu

    2010-01-01

    The light output and energy resolution of PbWO 4 crystal are studied with different wrapping materials and methods. The Wrapping condition was optimized by analyzing the experimental data to gain higher light output and better energy resolution. A GEANT4-based package has been developed to simulate the corresponding features of PbWO 4 crystal, and the simulation results are consistent with the experimental data. (authors)

  1. Controllable Fabrication of Ordered Mesoporous Bi2WO6 and Its High Photocatalytic Activity under Visible Light

    Directory of Open Access Journals (Sweden)

    Xueming Dang

    2014-01-01

    Full Text Available Ordered mesoporous Bi2WO6 was fabricated by nanocasting technique using SBA-15 as the template. The effect of the dosage of SBA-15 on the formation of the ordered structure and the photocatalytic ability of mesoporous Bi2WO6 was discussed. It was confirmed that the ordered mesoporous structure was obtained as the dosage of SBA-15 was 0.3 g. It was found that, compared to Bi2WO6, the RhB degradation rate with ordered mesoporous Bi2WO6 was enhanced under visible light (λ>400 nm by the photocatalytic measurements. The enhanced photocatalytic performance of ordered mesoporous Bi2WO6 was attributed to its particular ordered mesoporous structure which could increase the light-harvesting efficiency, reduce the recombination of the photogenerated charge carriers, and promote the surface reaction.

  2. Recycled Concrete as Aggregate for Structural Concrete Production

    Directory of Open Access Journals (Sweden)

    Mirjana Malešev

    2010-04-01

    Full Text Available A comparative analysis of the experimental results of the properties of fresh and hardened concrete with different replacement ratios of natural with recycled coarse aggregate is presented in the paper. Recycled aggregate was made by crushing the waste concrete of laboratory test cubes and precast concrete columns. Three types of concrete mixtures were tested: concrete made entirely with natural aggregate (NAC as a control concrete and two types of concrete made with natural fine and recycled coarse aggregate (50% and 100% replacement of coarse recycled aggregate. Ninety-nine specimens were made for the testing of the basic properties of hardened concrete. Load testing of reinforced concrete beams made of the investigated concrete types is also presented in the paper. Regardless of the replacement ratio, recycled aggregate concrete (RAC had a satisfactory performance, which did not differ significantly from the performance of control concrete in this experimental research. However, for this to be fulfilled, it is necessary to use quality recycled concrete coarse aggregate and to follow the specific rules for design and production of this new concrete type.

  3. How Concrete Is Concrete?

    Science.gov (United States)

    Gravemeijer, Koeno

    2011-01-01

    If we want to make something concrete in mathematics education, we are inclined introduce, what we call, "manipulatives", in the form of tactile objects or visual representations. If we want to make something concrete in a everyday-life conversation, we look for an example. In the former, we try to make a concrete model of our own,…

  4. Usage of Crushed Concrete Fines in Decorative Concrete

    Science.gov (United States)

    Pilipenko, Anton; Bazhenova, Sofia

    2017-10-01

    The article is devoted to the questions of usage of crushed concrete fines from concrete scrap for the production of high-quality decorative composite materials based on mixed binder. The main problem in the application of crushed concrete in the manufacture of decorative concrete products is extremely low decorative properties of crushed concrete fines itself, as well as concrete products based on them. However, crushed concrete fines could have a positive impact on the structure of the concrete matrix and could improve the environmental and economic characteristics of the concrete products. Dust fraction of crushed concrete fines contains non-hydrated cement grains, which can be opened in screening process due to the low strength of the contact zone between the hydrated and non-hydrated cement. In addition, the screening process could increase activity of the crushed concrete fines, so it can be used as a fine aggregate and filler for concrete mixes. Previous studies have shown that the effect of the usage of the crushed concrete fines is small and does not allow to obtain concrete products with high strength. However, it is possible to improve the efficiency of the crushed concrete fines as a filler due to the complex of measures prior to mixing. Such measures may include a preliminary mechanochemical activation of the binder (cement binder, iron oxide pigment, silica fume and crushed concrete fines), as well as the usage of polycarboxylate superplasticizers. The development of specific surface area of activated crushed concrete fines ensures strong adhesion between grains of binder and filler during the formation of cement stone matrix. The particle size distribution of the crushed concrete fines could achieve the densest structure of cement stone matrix and improve its resistance to environmental effects. The authors examined the mechanisms of structure of concrete products with crushed concrete fines as a filler. The results of studies of the properties of

  5. A study of transition from n- to p-type based on hexagonal WO3 nanorods sensor

    Science.gov (United States)

    Wu, Ya-Qiao; Hu, Ming; Wei, Xiao-Ying

    2014-04-01

    Hexagonal WO3 nanorods are fabricated by a facile hydrothermal process at 180 °C using sodium tungstate and sodium chloride as starting materials. The morphology, structure, and composition of the prepared nanorods are studied by scanning electron microscopy, X-ray diffraction spectroscopy, and energy dispersive spectroscopy. It is found that the agglomeration of the nanorods is strongly dependent on the PH value of the reaction solution. Uniform and isolated WO3 nanorods with diameters ranging from 100 nm-150 nm and lengths up to several micrometers are obtained at PH = 2.5 and the nanorods are identified as being hexagonal in phase structure. The sensing characteristics of the WO3 nanorod sensor are obtained by measuring the dynamic response to NO2 with concentrations in the range 0.5 ppm-5 ppm and at working temperatures in the range 25 °C-250 °C. The obtained WO3 nanorods sensors are found to exhibit opposite sensing behaviors, depending on the working temperature. When being exposed to oxidizing NO2 gas, the WO3 nanorod sensor behaves as an n-type semiconductor as expected when the working temperature is higher than 50 °C, whereas, it behaves as a p-type semiconductor below 50 °C. The origin of the n- to p-type transition is correlated with the formation of an inversion layer at the surface of the WO3 nanorod at room temperature. This finding is useful for making new room temperature NO2 sensors based on hexagonal WO3 nanorods.

  6. A study of transition from n- to p-type based on hexagonal WO3 nanorods sensor

    International Nuclear Information System (INIS)

    Wu Ya-Qiao; Hu Ming; Wei Xiao-Ying

    2014-01-01

    Hexagonal WO 3 nanorods are fabricated by a facile hydrothermal process at 180 °C using sodium tungstate and sodium chloride as starting materials. The morphology, structure, and composition of the prepared nanorods are studied by scanning electron microscopy, X-ray diffraction spectroscopy, and energy dispersive spectroscopy. It is found that the agglomeration of the nanorods is strongly dependent on the PH value of the reaction solution. Uniform and isolated WO 3 nanorods with diameters ranging from 100 nm–150 nm and lengths up to several micrometers are obtained at PH = 2.5 and the nanorods are identified as being hexagonal in phase structure. The sensing characteristics of the WO 3 nanorod sensor are obtained by measuring the dynamic response to NO 2 with concentrations in the range 0.5 ppm–5 ppm and at working temperatures in the range 25 °C–250 °C. The obtained WO 3 nanorods sensors are found to exhibit opposite sensing behaviors, depending on the working temperature. When being exposed to oxidizing NO 2 gas, the WO 3 nanorod sensor behaves as an n-type semiconductor as expected when the working temperature is higher than 50 °C, whereas, it behaves as a p-type semiconductor below 50 °C. The origin of the n- to p-type transition is correlated with the formation of an inversion layer at the surface of the WO 3 nanorod at room temperature. This finding is useful for making new room temperature NO 2 sensors based on hexagonal WO 3 nanorods. (general)

  7. Solar photocatalytic activity of TiO2 modified with WO3 on the degradation of an organophosphorus pesticide

    International Nuclear Information System (INIS)

    Ramos-Delgado, N.A.; Gracia-Pinilla, M.A.; Maya-Treviño, L.; Hinojosa-Reyes, L.; Guzman-Mar, J.L.; Hernández-Ramírez, A.

    2013-01-01

    Highlights: • TiO 2 and WO 3 /TiO 2 (2 and 5%) were tested in the photocatalytic malathion degradation. • The use of solar radiation in the photocatalytic degradation process was evaluated. • Modified catalyst showed greater photocatalytic activity than pure TiO 2 . • The mineralization rate was improved when WO 3 content on TiO 2 was 2%. -- Abstract: In this study, the solar photocatalytic activity (SPA) of WO 3 /TiO 2 photocatalysts synthesized by the sol–gel method with two different percentages of WO 3 (2 and 5%wt) was evaluated using malathion as a model contaminant. For comparative purpose bare TiO 2 was also prepared by sol–gel process. The powders were characterized by X-ray diffraction (XRD), Raman spectroscopy, diffuse reflectance UV–vis spectroscopy (DRUV–vis), specific surface area by the BET method (SSA BET ), scanning electron microscopy (SEM), high resolution transmission electron microscopy (HRTEM) and scanning transmission electron microscopy with a high annular angle dark field detector (STEM-HAADF). The XRD, Raman, HRTEM and STEM-HAADF analyses indicated that WO 3 was present as a monoclinic crystalline phase with nanometric cluster sizes (1.1 ± 0.1 nm for 2% WO 3 /TiO 2 and 1.35 ± 0.3 nm for 5% WO 3 /TiO 2 ) and uniformly dispersed on the surface of TiO 2 . The particle size of the materials was 19.4 ± 3.3 nm and 25.6 ± 3 nm for 2% and 5% WO 3 /TiO 2 , respectively. The SPA was evaluated on the degradation of commercial malathion pesticide using natural solar light. The 2% WO 3 /TiO 2 photocatalyst exhibited the best photocatalytic activity achieving 76% of total organic carbon (TOC) abatement after 300 min compared to the 5% WO 3 /TiO 2 and bare TiO 2 photocatalysts, which achieved 28 and 47% mineralization, respectively. Finally, experiments were performed to assess 2% WO 3 /TiO 2 catalyst activity on repeated uses; after several successive cycles its photocatalytic activity was retained showing long-term stability

  8. Enhanced performance of direct Z-scheme CuS-WO 3 system towards photocatalytic decomposition of organic pollutants under visible light

    Energy Technology Data Exchange (ETDEWEB)

    Song, Chundong; Wang, Xiang; Zhang, Jing; Chen, Xuebing; Li, Can

    2017-12-01

    CuS-WO3 composites were synthesized by an in situ solution method at low temperature. The crystalline phase, morphology, particle size, and the optical properties of CuS-WO3 samples were characterized by XRD, SEM, XPS, and UV–vis diffuse reflectance spectra. CuS-WO3 composites showed much higher activity for photocatalytic degradation of RhB as compared with WO3 and CuS. The degradation rate constant over 1 wt% CuS-WO3 catalyst was 4.4 times and 9.2 times higher than that of WO3 and CuS, respectively. It is found that holes (h+) and superoxide radical anions (O2-) are the dominant reactive species by using methanol, disodium ethylenediaminetetraacetate (EDTA) and ascorbic acid as scavengers. Band structure analysis shows that bottom of CB of WO3 is very similar with and higher (ca. 0.01 eV) than the top of VB of CuS. The results of PL showed that the similarity renders the recombination between photogenerated holes on the VB of CuS and photogenerated electrons on the CB of WO3 possible and easy, forming a direct Z-scheme in CuS-WO3. This result in that more electrons in the CB of CuS and holes in the VB of WO3 survived, and then participated in the photocatalytic degradation of RhB, showing an increased activity.

  9. Luminescent and structural properties of Zn_xMg_1_-_xWO_4 mixed crystals

    International Nuclear Information System (INIS)

    Krutyak, N.; Nagirnyi, V.; Spassky, D.; Tupitsyna, I.; Dubovik, A.; Belsky, A.

    2016-01-01

    The structural and luminescent properties of perspective scintillating Zn_xMg_1_-_xWO_4 mixed crystals were studied. The following characteristics were found to depend linearly on x value: the energy of several vibrational modes detected by Raman spectroscopy, the bandgap width deduced from the shift of the excitation spectrum onset of a self-trapped exciton (STE) emission, the position of thermally stimulated luminescence peaks. It is also shown that the thermal stability of the STE luminescence decreases gradually when x decreases. These data indicate that each Zn_xMg_1_-_xWO_4 mixed crystal is not a mixture of two constituents, but possesses its original crystalline structure, as well as optical and luminescent properties. - Highlights: • The structural and luminescent properties of Zn_xMg_1_-_xWO_4 were studied. • The energy of Raman modes, the bandgap width, TSL peak position linearly depend on x. • Each Zn_xMg_1_-_xWO_4 possesses its original crystalline structure.

  10. Hierarchical Bi{sub 2}WO{sub 6} architectures decorated with Pd nanoparticles for enhanced visible-light-driven photocatalytic activities

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Jinniu; Chen, Tianhua [School of Physics and Information Technology, Shaanxi Normal University, Xi’an, 710062 (China); Lu, Hongbing, E-mail: hblu@snnu.edu.cn [School of Physics and Information Technology, Shaanxi Normal University, Xi’an, 710062 (China); Yang, Zhibo; Yin, Feng; Gao, Jianzhi; Liu, Qianru [School of Physics and Information Technology, Shaanxi Normal University, Xi’an, 710062 (China); Tu, Yafang [Department of Physics, Institute for Interdisciplinary Research, Jianghan University, Wuhan, 430056 (China)

    2017-05-15

    Highlights: • A new kind of Pd decorated Bi{sub 2}WO{sub 6} hierarchical microarchitecture was synthesized. • Pd nanoparticles remarkably improved the photocatalytic activity of Bi{sub 2}WO{sub 6}. • The photo-generated holes and ·O{sub 2}{sup −} played a crucial role in the degradation of RhB. • The photocatalytic enhancement mechanism of the Pd-Bi{sub 2}WO{sub 6} composites was proposed. - Abstract: A new kind of hierarchical Pd-Bi{sub 2}WO{sub 6} architecture decorated with different molar ratios of Pd to Bi, has been fabricated by a hydrothermal process, followed by a chemical deposition method. The photocatalytic activities of the pure Bi{sub 2}WO{sub 6} and Pd-Bi{sub 2}WO{sub 6} nanocatalyst were examined in the degradation of Rhodamine B (RhB) dyes and phenol under visible light. The photocatalytic results showed that the Pd-Bi{sub 2}WO{sub 6} nanocomposites possessed observably enhanced photocatalytic activities. Particularly, the 2.0% Pd loaded Bi{sub 2}WO{sub 6} had the highest photocatalytic activity, exhibiting a nearly complete degradation of 30 mg/L RhB and 10 mg/L phenol within only 50 and 60 min, respectively. In addition, the trapping experiment results indicated that the photo-generated holes (h{sup +}) and ·O{sub 2}{sup −} played a crucial role in the degradation of RhB. According to the experimental results, the photocatalytic degradation mechanism of Pd-Bi{sub 2}WO{sub 6} was also proposed. The enhanced photocatalytic activities were ascribed to the combined effects of the highly efficient separation of electrons and holes, improved visible light utilization and increased BET specific surface areas of the Pd-Bi{sub 2}WO{sub 6} nanocomposites.

  11. Red photoluminescent property and modification of WO3:Eu3+ inverse opal for blue light converted LEDs

    Science.gov (United States)

    Ruan, Jiufeng; Yang, Zhengwen; Huang, Anjun; Chai, Zhuangzhuang; Qiu, Jianbei; Song, Zhiguo

    2018-01-01

    Blue light converted light-emitting diodes is of great significance as a candidate for next generation lighting. In this work, the WO3:Eu3+ inverse opal photonic crystals were prepared and their luminescence properties were studied. The results demonstrated that the main excitation peak of WO3:Eu3+ inverse opals were located at 465 nm. The red luminescence peak at the 613 nm was observed in the WO3:Eu3+ inverse opal upon 465 nm excitation, exhibiting better red color purity. The influence of photonic band gap on the photoluminescence of WO3:Eu3+ inverse opal was obtained. When the red luminescence peak is in the regions of the photonic band gap and the edge of the band-gap, the red luminescence suppression and enhancement was observed respectively. The WO3:Eu3+ inverse opals may be a promising candidate for the blue light converted LEDs.

  12. Defect engineering of two-dimensional WO{sub 3} nanosheets for enhanced electrochromism and photoeletrochemical performance

    Energy Technology Data Exchange (ETDEWEB)

    Zhou, Xiaofang; Zheng, Xiaoli; Yan, Bo; Xu, Tao; Xu, Qun, E-mail: qunxu@zzu.edu.cn

    2017-04-01

    Highlights: • We establish a facile strategy by solvothermal reaction and hydrogenation to synthesize 2D WO{sub 3} ultrathin nanosheets with abundant oxygen vacancies. • We find that the hydrogenated WO{sub 3} ultrathin nanosheets exhibit outstanding electrochromism properties. • Moreover, the hydrogenated WO{sub 3} nanosheets also exhibit remarkable photocatalytic performance. • The outstanding electrochromism and photoelectrochemical performances are mainly due to increased oxygen vacancies and narrowed band gap. - Abstract: The capability of introduction of oxygen vacancies in a controlled way has emerged as the heart of modern transition metal oxide semiconductor chemistry. As chemical defects, the oxygen vacancies have been proposed as electron donors, which are prone to increase carrier density and promote charge carrier separation. Herein, we have successfully prepared 2D WO{sub 3} ultrathin nanosheets with abundant surface oxygen vacancies by a combination of facile solvothermal reaction and hydrogenation method. The resultant hydrogenated WO{sub 3} ultrathin nanosheets exhibit remarkable electrochromism and photocatalytic performances compared with the non-hydrogenated samples, mainly due to their increased oxygen vacancies, narrowed band gap coupled with fast charge transfer and enhanced adsorption of visible light.

  13. Nest-like structures of Sr doped Bi2WO6: Synthesis and enhanced photocatalytic properties

    International Nuclear Information System (INIS)

    Liu Ying; Wang Weimin; Fu Zhengyi; Wang Hao; Wang Yucheng; Zhang Jinyong

    2011-01-01

    Highlights: → Bi 2 WO 6 with 3D nest-like structures was obtained without the presence of templates but after Sr-doping, which represents a marked improvement over previous reports. → The products showed enhanced photocatalytic properties over pure Bi 2 WO 6 . → Samples subsequently thermal treated at 500 deg. C show better photocatalytic activities. - Abstract: A series of Sr-doped Bi 2 WO 6 with three-dimensional (3D) nest-like structures were synthesized through simple hydrothermal route and characterized by XRD, FESEM, TEM, XPS, UV-vis DRS, etc. Morphology observation revealed that the as-synthesized Bi 2 WO 6 were self-assembled three-dimensional (3D) nest-like structures, which were constructed from nanoplates. UV-vis diffuse reflectance spectra indicated that the samples had absorption in both UV and visible light areas. Their photocatalytic activities were evaluated by photodegradation of rhodamine B (RhB) under UV and visible light irradiation (λ > 420 nm). The photocatalytic properties were enhanced after Sr doping. Samples subsequently thermal treated at 500 deg. C showed higher photocatalytic activities. The reasons for the differences in the photocatalytic activities of these nest-like Bi 2 WO 6 microstructures were further investigated.

  14. Cross-cultural adaptation of the Work Disability Diagnosis Interview (WoDDI for the Brazilian context Adaptación transcultural del Work Disability Diagnosis Interview (WoDDI para el contexto brasileño Adaptação transcultural do Work Disability Diagnosis Interview (WoDDI para o contexto brasileiro

    Directory of Open Access Journals (Sweden)

    Vivian Aline Mininel

    2012-02-01

    Full Text Available The Work Disability Diagnosis Interview (WoDDI is a structured interview guide developed by the University of Sherbrooke, Canada to help clinicians detect the most important work-related disability predictors and to identify one or more causes of prolonged absenteeism. This methodological study aims for the cross-cultural adaptation of the WoDDI for the Brazilian context. The method followed international guidelines for studies of this kind, including the following steps: initial translation, synthesis of translations, back translation, evaluation by an expert committee and testing of the penultimate version. These steps allowed obtaining conceptual, semantic, idiomatic, experiential and operational equivalences, in addition to content validity. The results showed that the translated WoDDI is adapted to the Brazilian context and can be used after training.El Work Disability Diagnosis Interview (WoDDI es una guía de entrevista estructurada desarrollada por la Universidad de Sherbrooke (Canadá, para ayudar a los profesionales de la salud a detectar los predictores de mayor importancia para personas con trastornos relacionados con el trabajo y para identificar una o más causas de ausentismo prolongado del trabajo. Este estudio metodológico se dirige a la adaptación transcultural (WoDDI para el contexto brasileño. El método siguió las recomendaciones internacionales para este tipo de estudio, el que comprende las siguientes etapas: traducción inicial, síntesis de las traducciones, retraducción, revisión del comité de expertos y prueba de la versión pre-final. Estas medidas permitieron obtener la equivalencia conceptual, semántica, idiomática y la experiencia operacional, además de la validación del contenido. Los resultados mostraron que el WoDDI traducido se adapta a la realidad brasileña e puede ser utilizado, después de la capacitación previa.O Work Disability Diagnosis Interview (WoDDI é um guia de entrevista estruturada

  15. Correlation between excited d-orbital electron lifetime in polaron dynamics and coloration of WO3 upon ultraviolet exposure

    Science.gov (United States)

    Lee, Young-Ahn; Han, Seung-Ik; Rhee, Hanju; Seo, Hyungtak

    2018-05-01

    Polarons have been suggested to explain the mechanism of the coloration of WO3 induced by UV light. However, despite the many experimental results that support small polarons as a key mechanism, direct observation of the carrier dynamics of polarons have yet to be reported. Here, we investigate the correlation between the electronic structure and the coloration of WO3 upon exposure to UV light in 5% H2/N2 gas and, more importantly, reveal photon-induced excited d-electron generation/relaxation via the W5+ oxidation state. The WO3 is fabricated by radio-frequency magnetron sputtering. X-ray diffraction patterns show that prepared WO3 is amorphous. Optical bandgap of 3.1 eV is measured by UV-vis before and after UV light. The results of Fourier transform infrared and Raman exhibit pristine WO3 is formed with surface H2O. The colored WO3 shows reduced state of W5+ state (34.3 eV) by using X-ray photoelectron spectroscopy. The valence band maximum of WO3 after UV light in H2 is shifted from mid gap to shallow donor by using ultraviolet photoelectron spectroscopy. During the exploration of the carrier dynamics, pump (700 nm)-probe (1000 nm) spectroscopy at the femtosecond scale was used. The results indicated that electron-phonon relaxation of UV-irradiated WO3, which is the origin of the polaron-induced local surface plasmonic effect, is dominant, resulting in slow decay (within a few picoseconds); in contrast, pristine WO3 shows fast decay (less than a picosecond). Accordingly, the long photoinduced carrier relaxation is ascribed to the prolonged hot-carrier lifetime in reduced oxides resulting in a greater number of free d-electrons and, therefore, more interactions with the W5+ sub-gap states.

  16. Giant Persistent Photoconductivity of the WO3 Nanowires in Vacuum Condition

    Directory of Open Access Journals (Sweden)

    Huang Kai

    2011-01-01

    Full Text Available Abstract A giant persistent photoconductivity (PPC phenomenon has been observed in vacuum condition based on a single WO3 nanowire and presents some interesting results in the experiments. With the decay time lasting for 1 × 104 s, no obvious current change can be found in vacuum, and a decreasing current can be only observed in air condition. When the WO3 nanowires were coated with 200 nm SiO2 layer, the photoresponse almost disappeared. And the high bias and high electric field effect could not reduce the current in vacuum condition. These results show that the photoconductivity of WO3 nanowires is mainly related to the oxygen adsorption and desorption, and the semiconductor photoconductivity properties are very weak. The giant PPC effect in vacuum condition was caused by the absence of oxygen molecular. And the thermal effect combining with oxygen re-adsorption can reduce the intensity of PPC.

  17. Electron microscopy analyses and electrical properties of the layered Bi2WO6 phase

    International Nuclear Information System (INIS)

    Taoufyq, A.; Ait Ahsaine, H.; Patout, L.; Benlhachemi, A.; Ezahri, M.

    2013-01-01

    The bismuth tungstate Bi 2 WO 6 was synthesized using a classical coprecipitation method followed by a calcination process at different temperatures. The samples were characterized by X-ray diffraction, simultaneous thermogravimetry and differential thermal analysis (TGA/DTA), scanning and transmission electron microscopy (SEM, TEM) analyses. The Rietveld analysis and electron diffraction clearly confirmed the Pca2 1 non centrosymmetric space group previously proposed for this phase. The layers Bi 2 O 2 2+ and WO 4 2− have been directly evidenced from the HRTEM images. The electrical properties of Bi 2 WO 6 compacted pellets systems were determined from electrical impedance spectrometry (EIS) and direct current (DC) analyses, under air and argon, between 350 and 700 °C. The direct current analyses showed that the conduction observed from EIS analyses was mainly ionic in this temperature range, with a small electronic contribution. Electrical change above the transition temperature of 660 °C is observed under air and argon atmospheres. The strong conductivity increase observed under argon is interpreted in terms of formation of additional oxygen vacancies coupled with electron conduction. - Graphical abstract: High resolution transmission electron microscopy: inverse fast Fourier transform giving the layered structure of the Bi 2 WO 6 phase, with a representation of the cell dimensions (b and c vectors). The Bi 2 O 2 2+ and WO 4 2− sandwiches are visible in the IFFT image. - Highlights: • Using transmission electron microscopy, we visualize the layered structure of Bi 2 WO 6 . • Electrical analyses under argon gas show some increase in conductivity. • The phase transition at 660 °C is evidenced from electrical modification

  18. A facile synthesis of ZnWO{sub 4} nanoparticles by microwave assisted technique and its application in photocatalysis

    Energy Technology Data Exchange (ETDEWEB)

    Garadkar, K.M., E-mail: kmg_chem@unishivaji.ac.in [Nanomaterials Research Laboratory, Department of Chemistry, Shivaji University, Kolhapur 416 004, MS (India); Ghule, L.A. [Nanomaterials Research Laboratory, Department of Chemistry, Shivaji University, Kolhapur 416 004, MS (India); Sapnar, K.B.; Dhole, S.D. [Microtron Accelerator Laboratory, Department of Physics, University of Pune, Pune 411 007, MS (India)

    2013-03-15

    Highlights: ► Nanocrystalline ZnWO{sub 4} particles were successfully prepared by a microwave method. ► Spherical morphology with a 10 nm size. ► The band is 3.4 eV. ► The photodegradation of RhB was 95% within 25 min. - Abstract: A simple microwave assisted technique has been successfully developed to synthesize ZnWO{sub 4} nanoparticles. The X-ray diffraction results indicated that the synthesized nanoparticles exhibited only wolframite structure. Structural, morphological and optical properties of ZnWO{sub 4} nanoparticles have been analyzed by XRD, SEM, TEM EDAX, UV–vis and FT-IR spectral measurements. The transmission electron microscopy (TEM) image revealed that particle size of ZnWO{sub 4} nanoparticles was found to be 10 nm, the band-gap of ZnWO{sub 4} nanoparticles was found to be 3.4 eV. The photocatalytic activities for aqueous Rhodamine B and Methylene Blue samples were investigated and observed that ZnWO{sub 4} nanoparticles exhibited highly enhanced photocatalytic activity towards RhB than MB.

  19. Hydrothermal deposition and photochromic performances of three kinds of hierarchical structure arrays of WO{sub 3} thin films

    Energy Technology Data Exchange (ETDEWEB)

    Ding, Defang; Shen, Yi, E-mail: sysy7373@163.com; Ouyang, Yali; Li, Zhen

    2012-10-01

    Three kinds of tungsten oxide (WO{sub 3}) thin films have been fabricated by a simple hydrothermal deposition method. Scanning electron microscopy images of the products revealed that the capping agents did impact the microstructure of WO{sub 3} films. Films prepared without capping agents were ordered nanorod arrays, while the ones obtained with ethanol and oxalic acid revealed peeled-orange-like and cauliflower-like hierarchical structure arrays, respectively. Both of the two hierarchical structures were composed of much thinner nanorods compared with the one obtained without capping agents. All the WO{sub 3} films exhibited good photochromic properties and the two with inducers performed even better, which could be due to the changes in the microstructure that increased the amount of photogenerated electron-hole pairs and the proton diffusion rates. - Highlights: Black-Right-Pointing-Pointer Ordered WO{sub 3} nanorod arrays were prepared by hydrothermal deposition process. Black-Right-Pointing-Pointer Two hierarchical WO{sub 3} structure arrays were obtained with ethanol and oxalic acid. Black-Right-Pointing-Pointer Mechanism for the improved photochromic performances of WO{sub 3} films is proposed.

  20. Advanced nanostructured photocatalysts based on reduced graphene oxide-flower-like Bi_2WO_6 composites for an augmented simulated solar photoactivity activity

    International Nuclear Information System (INIS)

    Li, Yukun; Chen, Lin; Wang, Yue; Zhu, Liang

    2016-01-01

    Highlights: • A simple route was proposed to prepare flower-like Bi_2WO_6 and RGO/Bi_2WO_6. • Cipro HCl was degraded firstly by RGO/Bi_2WO_6 under the visible-light. • 2% RGO/Bi_2WO_6 exhibited the best removal efficiency. - Abstract: A simple hydrothermal process was proposed to prepare the flower-like Bi_2WO_6 architectures, and the as-synthesized Bi_2WO_6 photocatalysts were further processed with the prepared graphene oxide (GO) to form novel reduced graphene oxide (RGO)/Bi_2WO_6 composites. The nano-materials were characterized with the help of XRD, XPS, SEM, FTIR, UV-DRS, PL techniques to investigate their morphological, physical, optical, and photochemical properties. Photocatalytic performances of the pure flower-like Bi_2WO_6 architectures and RGO/Bi_2WO_6 composites were compared and evaluated through the degradation of ciprofloxacin hydrochloride (Cipro HCl) wastewater under the simulated visible light. It was found that the RGO/Bi_2WO_6 composites displayed enhanced visible light-driven photocatalytic activities. It might be that the RGO loading not only effectively suppressed the electron–hole recombination, but also increased the light absorption ability. The effects of operating condition involved in the photocatalytic process were further examined, and the cycle-stability experiment demonstrated that as-obtained 2% RGO/Bi_2WO_6 photocatalysts had good photocatalytic repeatability.

  1. Enhanced photocatalytic activity of cadmium-doped Bi{sub 2}WO{sub 6} nanoparticles under simulated solar light

    Energy Technology Data Exchange (ETDEWEB)

    Song, Xu Chun, E-mail: songxuchunfj@163.com; Li, Wen Ting [Fujian Normal University, Department of Chemistry (China); Huang, Wan Zhen; Zhou, Huan [Zhejiang University of Technology, Research Center of Analysis and Measurement (China); Yin, Hao Yong [Hangzhou Dianzi University, Institute of Environmental Science and Engineering (China); Zheng, Yi Fan [Zhejiang University of Technology, Research Center of Analysis and Measurement (China)

    2015-03-15

    Novel cadmium-doped Bi{sub 2}WO{sub 6} nanoparticles with different Cd contents have been synthesized by a one-step route using ethylene glycol and water as solvents at 180 °C for 12 h. The as-synthesized samples were characterized in detailed by SEM, XRD, EDS, HRTEM, UV–Vis DRS, BET techniques, and so on. The results shown that with the increase of the Cd{sup 2+} addition, the crystal structure, lattice space, and absorption edge were not significantly changed and the calculated band gap value was 2.58 eV. However, the flower-like Bi{sub 2}WO{sub 6} sphere was gradually destroyed. Simultaneously, the surface area and photocurrent responses of the catalysts were greatly increased. Photocatalytic activity of the Cd-doped Bi{sub 2}WO{sub 6} samples was determined by monitoring the change of RhB concentration under simulated solar light. The results revealed that cadmium doping greatly improved the photocatalytic efficiency of Bi{sub 2}WO{sub 6}. The Bi{sub 2}WO{sub 6} sample with R{sub Cd} = 0.05 displayed the highest photocatalytic activity, and the degradation rate is about two times greater than pure Bi{sub 2}WO{sub 6}. Moreover, the Cd–Bi{sub 2}WO{sub 6} photocatalyst remained stable even after five consecutive cycles. A possible mechanism of photocatalytic activity enhancement on basis of the experimental results was proposed.

  2. Preparation and optimization of CdWO_4-polymer nano-composite film as an alpha particle counter

    International Nuclear Information System (INIS)

    Ziluei, Hossein; Azimirad, Rouhollah; Mojtahedzadeh Larijani, Majid; Ziaie, Farhoud

    2017-01-01

    In this research work, CdWO_4/polymer composite films with different thicknesses were prepared using Poly-methyl acrylate polymer and synthesized CdWO_4 powder. The CdWO_4 powder was synthesized by a simple co-precipitation method in the laboratory. X-ray diffraction, photoluminescence, Fourier transformed infrared spectroscopy and energy-dispersive X-ray spectroscopy proved that the CdWO_4 powder was successfully prepared. Moreover, photoluminescence analysis showed that adding polymer does not change the emission peak of CdWO_4. Also, the responses of all samples were measured using an "2"4"1Am alpha source with 1860 Bq activity. Results showed that the sample having thickness of 177 mg/cm"2 has the best counting efficiency (over 2π geometry) among the others. The efficiency measurement was further evaluated using a "2"3"0Th source whose activity is 190.7 Bq. It revealed that the counting efficiency of this sample for both "2"4"1Am and "2"3"0Th was nearly equal.

  3. Numerical model of the catchments of the oziąbel and wołczyński strumień rivers - Wołczyn municipality

    Science.gov (United States)

    Olichwer, Tomasz; Wcisło, Marek; Staśko, Stanisław; Buczyński, Sebastian; Modelska, Magdalena; Tarka, Robert

    2012-10-01

    The article presents a numerical model designed for determining groundwater dynamics and water balance of the catchments of the Oziąbel (Czarna Woda) river and the Wołczyński Strumień river in Wołczyn region. Hydrogeological mapping and modelling research covered the area of 238.9 km2. As a result of measurements performed in 2008-2009, flows were determined in major rivers and water table positions were measured at 26 points. In the major part of the area described, the water table, lying at the depth of 1.5-18.7 m, has unconfined character, and the aquifer is built of Neogene (Quaternary) sands and gravels. In the area under study, groundwaters are drawn from 6 wells with total withdrawal of 6133 m3/d. The numerical modelling was performed with the use of Visual Modflow 3.1.0 software. The area was partitioned by a discretization grid with a step size l = 250 m. The conceptual model of the hydrogeological system is based on hydrological data gathered over a period of one year, data from HYDRO bank database, cross-sections and maps. The boundaries of the modelled hydrogeological system were established on the watersheds of the Wołczyński Strumień river and the Oziąbel river, apart from the areas where they run together. The modelled area was extended (271.5 km2) around the Wołczyński Strumień river catchment to achieve a more effective mapping of the anthropogenic impact on its balance and the hydrodynamic system of the catchment area. The structure is characterised by the occurrence of one or rarely two aquifers separated by a pack of Quaternary clays. The investigation produced a detailed water balance and its components.

  4. Mechanism Of Long Term Change In Electrochrcmism Of LixWO3 Films

    Science.gov (United States)

    Nagai, Junichi; Kamimori, Tadatoshi; Mizuhashi, Mamoru

    1984-11-01

    The degradation mechanism of gradual decrease of the contrast between colored and bleached states of Lix'. WO3 films with switching cycles was investigated. We made electro-chemical and quantitative chemical analyses to clarify this phenomenon. It was found that the decrease in contrast was mostly attributed to the parallel cathodic shift of emf(x), passibly caused by ion exchange reaction expressed by: WOH + Li+ WOLi + H. Fully ion-exchanged WO3 films showed no appreciable change in spite of the presence of a large amount of Li in them. These films were capable of accepting as much Li as the fresh films did on coloration and reached to the same optical densities. It is concluded that there are two kinds of active sites available for accepting lithium ions in the WO3 structure, one for ion exchange and the other for coloration.

  5. Recycled Concrete as Aggregate for Structural Concrete Production

    OpenAIRE

    Mirjana Malešev; Vlastimir Radonjanin; Snežana Marinković

    2010-01-01

    A comparative analysis of the experimental results of the properties of fresh and hardened concrete with different replacement ratios of natural with recycled coarse aggregate is presented in the paper. Recycled aggregate was made by crushing the waste concrete of laboratory test cubes and precast concrete columns. Three types of concrete mixtures were tested: concrete made entirely with natural aggregate (NAC) as a control concrete and two types of concrete made with natural fine and recycle...

  6. The Future Concrete: Self-Compacting Concrete

    OpenAIRE

    Iureş, Liana; Bob, Corneliu

    2010-01-01

    The paper presents the characteristics of the self-compacting concretes, their advantages and disadvantages when they are used in buildings. Due to its properties and composition, the self-compacting concrete is described here as being one of the future friendly enviromental material for buildings. Tests concerning to obtaining a self-compacting concrete, together with the specific fresh concrete properties tests, are described.

  7. Synthesis of WO{sub 3} nanoparticles by citric acid-assisted precipitation and evaluation of their photocatalytic properties

    Energy Technology Data Exchange (ETDEWEB)

    Sánchez-Martínez, D. [Departamento de Ecomateriales y Energía, Facultad de Ingeniería Civil (UANL), Ciudad Universitaria, C.P. 66451, San Nicolás de los Garza, N.L. (Mexico); Martínez-de la Cruz, A., E-mail: azael70@yahoo.com.mx [Facultad de Ingeniería Mecánica y Eléctrica, Universidad Autónoma de Nuevo León, Ciudad Universitaria, C.P. 66451, San Nicolás de los Garza, N.L. (Mexico); López-Cuéllar, E. [Facultad de Ingeniería Mecánica y Eléctrica, Universidad Autónoma de Nuevo León, Ciudad Universitaria, C.P. 66451, San Nicolás de los Garza, N.L. (Mexico)

    2013-02-15

    Graphical abstract: Display Omitted Highlights: ► WO{sub 3} nanoparticles were synthesized by a simple citric acid-assisted precipitation. ► WO{sub 3} photocatalyst was able to the partial mineralization of rhB, IC and MO. ► WO{sub 3} can be considered as a photocatalyst active under visible light irradiation. -- Abstract: WO{sub 3} nanoparticles were synthesized by citric acid-assisted precipitation method using a 1:1.5 molar ratio of ammonium paratungstate hydrate (H{sub 42}N{sub 10}O{sub 42}W{sub 12}·xH{sub 2}O):citric acid (C{sub 6}H{sub 8}O{sub 7}). The formation of monoclinic crystal structure of WO{sub 3} at different temperatures was confirmed by X-ray powder diffraction (XRD). The characterization of the samples synthesized was complemented by transmission electron microscopy (TEM), Brunauer–Emmitt–Teller surface area (BET) and diffuse reflectance spectroscopy (DRS). According to the thermal treatment followed during the synthesis of WO{sub 3}, the morphology of the nanoparticles formed was characterized by rectangular and ovoid shapes. The photocatalytic activity of WO{sub 3} obtained under different experimental conditions was evaluated in the degradation of rhodamine B (rhB), indigo carmine (IC), methyl orange (MO), and Congo red (CR) in aqueous solution under UV and UV–vis radiation. The highest photocatalytic activity was observed in the sample obtained by thermal treatment at 700 °C. In general, the sequence of degradation of the organic dyes was: indigo carmine (IC) > rhodamine B (rhB) > methyl orange (MO) > Congo red (CR). The mineralization degree of organic dyes by WO{sub 3} photocatalysts was determined by total organic carbon analysis (TOC) reaching percentages of mineralization of 82% (rhB), 85% (IC), 28% (MO), and 7% (CR) for 96 h of lamp irradiation.

  8. THE DISCOVERY OF A RARE WO-TYPE WOLF–RAYET STAR IN THE LARGE MAGELLANIC CLOUD

    International Nuclear Information System (INIS)

    Neugent, Kathryn F.; Massey, Philip; Morrell, Nidia

    2012-01-01

    While observing OB stars within the most crowded regions of the Large Magellanic Cloud, we happened upon a new Wolf-Rayet (WR) star in Lucke-Hodge 41, the rich OB association that contains S Doradus and numerous other massive stars. At first glance the spectrum resembled that of a WC4 star, but closer examination showed strong O VI λλ3811, 34 lines, leading us to classify it as a WO4. This is only the second known WO in the LMC, and the first known WO4 (the other being a WO3). This rarity is to be expected due to these stars' short lifespans as they represent the most advanced evolutionary stage in a massive star's lifetime before exploding as supernovae. This discovery shows that while the majority of WRs within the LMC have been discovered, there may be a few WRs left to be found.

  9. The Future Concrete: Self-Compacting Concrete

    Directory of Open Access Journals (Sweden)

    Liana Iureş

    2010-01-01

    Full Text Available The paper presents the characteristics of the self-compacting concretes, their advantages and disadvantages when they are used in buildings. Due to its properties and composition, the self-compacting concrete is described here as being one of the future friendly enviromental material for buildings. Tests concerning to obtaining a self-compacting concrete, together with the specific fresh concrete properties tests, are described.

  10. Hydrothermal synthesis of hierarchical WO{sub 3} nanostructures for dye-sensitized solar cells

    Energy Technology Data Exchange (ETDEWEB)

    Rashad, M.M. [Central Metallurgical Research and Development Institute (CMRDI), Helwan, P.O. Box 87, Cairo (Egypt); Shalan, A.E. [Central Metallurgical Research and Development Institute (CMRDI), Helwan, P.O. Box 87, Cairo (Egypt); Friedrich-Alexander-University of Erlangen-Nuremberg, Institute of Materials for Electronics and Energy Technology (i-MEET), Erlangen (Germany)

    2014-08-15

    Hierarchical architectures consisting of one-dimensional (1D) nanostructures are of great interest for potential use in energy and environmental applications in recent years. In this work, hierarchical tungsten oxide (WO{sub 3}) has been synthesized via a facile hydrothermal route from ammonium metatungstate hydrate and implemented as photoelectrode for dye-sensitized solar cells. The urchin-like WO{sub 3} micro-patterns are constructed by self-organized nanoscale length 1D building blocks, which are single crystalline in nature, grown along (001) direction and confirm an orthorhombic crystal phase. The obtained powders were investigated by XRD, SEM, TEM and UV-Vis Spectroscopy. The photovoltaic performance of dye-sensitized solar cells based on WO{sub 3} photoanodes was investigated. With increasing the calcination temperature of the prepared nanopowders, the light-electricity conversion efficiency (η) was increased. The results were attributed to increase the crystallinity of the particles and ease of electron movement. The DSSC based on hierarchical WO{sub 3} showed a short-circuit current, an open-circuit voltage, a fill factor, and a conversion efficiency of 4.241 mA/cm{sup 2}, 0.656 V, 66.74, and 1.85 %, respectively. (orig.)

  11. Structural studies of WO3-TeO2 glasses by high-Q-neutron diffraction and Raman spectroscopy

    International Nuclear Information System (INIS)

    Khanna, A.; Kaur, A.; Krishna, P.S.R.; Shinde, A.B.

    2013-01-01

    Glasses from the system: xWO 3 -(100-x)TeO 2 (x=15, 20 and 25 mol %) were prepared by melt quenching technique and characterized by density, UV-visible absorption spectroscopy, Differential Scanning Calorimetry (DSC), Raman spectroscopy and high-Q neutron diffraction measurements. Glass density and glass transition temperature increased with increase in WO 3 concentration, Raman spectroscopy indicated the conversion of TeO 4 units into TeO 3 units with increase in WO 3 content. The increase in glass transition temperature with the incorporation of WO 3 was attributed to the increase in average bond strength of the glass network since the bond dissociation energy of W-O bonds (672 kJ/mol) is significantly higher than that of Te-O bonds (376 kJ/mol). UV-visible studies found a very strong optical absorption band due to W 6+ ions, just below the absorption edge. High-Q neutron diffraction measurements were performed on glasses and radial distribution function analyses revealed changes in W-O and Te-O correlations in the glass network. The findings about changes in glass structure from neutron diffraction studies were consistent with structural information obtained from Raman spectroscopy and structure-property correlations were made. (author)

  12. Managing SRS competition in a miniature visible Nd:YVO4/BaWO4 Raman laser.

    Science.gov (United States)

    Li, Xiaoli; Lee, Andrew J; Huo, Yujing; Zhang, Huaijin; Wang, Jiyang; Piper, James A; Pask, Helen M; Spence, David J

    2012-08-13

    We demonstrate the operation of a compact and efficient continuous wave (CW) self-Raman laser utilizing a Nd:YVO4 gain crystal and BaWO4 Raman crystal, generating yellow emission at 590 nm. We investigate the competition that occurs between Stokes lines in the Nd:YVO4 and BaWO4 crystals, and within the BaWO4 crystal itself. Through careful consideration of crystal length and orientation, we are able to suppress competition between Stokes lines, and generate pure yellow emission at 590 nm with output power of 194 mW for just 3.8 W pump power.

  13. Photodegradation of Malachite Green by Nanostructured Bi2WO6 Visible Light-Induced Photocatalyst

    OpenAIRE

    Yijie Chen; Yaqin Zhang; Chen Liu; Aimin Lu; Weihua Zhang

    2012-01-01

    Bi2WO6 photocatalyst was first utilized to degrade malachite green. The effects of the concentration of malachite green, the pH value, and the concentration of Bi2WO6 on the photocatalytic efficiency were investigated. This study presents a strategy to eliminate highly toxic and persistent dyes such as malachite green.

  14. Nano Ag@AgBr surface-sensitized Bi{sub 2}WO{sub 6} photocatalyst: oil-in-water synthesis and enhanced photocatalytic degradation

    Energy Technology Data Exchange (ETDEWEB)

    Lin, Shuanglong; Liu, Li; Hu, Jinshan; Liang, Yinghua, E-mail: liangyh@heuu.edu.cn; Cui, Wenquan, E-mail: wkcui@163.com

    2015-01-01

    Graphical abstract: - Highlights: • The plasmatic Ag@AgBr surface-sensitized Bi{sub 2}WO{sub 6} composite photocatalysts. • Ag@AgBr greatly increased visible-light absorption for Bi{sub 2}WO{sub 6}. • The plasmonic photocatalysts exhibited enhanced activity for the degradation of MB, phenol and salicylic acid. - Abstract: Nano Ag@AgBr decorated on the surface of flower-like Bi{sub 2}WO{sub 6} (hereafter designated Ag@AgBr/Bi{sub 2}WO{sub 6}) were prepared via a facile oil-in-water self-assembly method. The photocatalysts were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), UV–vis diffuse reflectance spectroscopy (DRS), etc. The characterization results indicated that nano Ag@AgBr was observed to be evenly dispersed on the surface of Bi{sub 2}WO{sub 6}, and was approximately 20 nm in size. Ag@AgBr/Bi{sub 2}WO{sub 6} composites exhibited excellent UV–vis absorption, due to quantum dimension effect of Ag@AgBr, the surface plasmonic resonance (SPR) of Ag nanoparticles and the special flower-like structure of Bi{sub 2}WO{sub 6}. The photoelectrochemical measurement verified that the suitable band potential of Ag@AgBr and Bi{sub 2}WO{sub 6} and the existence of metal Ag resulted in the high efficiency in charge separation of the composite. The photocatalytic activities of the Ag@AgBr/Bi{sub 2}WO{sub 6} samples were examined under visible-light irradiation for the degradation of methylene blue (MB). The composite presented excellent photocatalytic activity due to the synergetic effect of Bi{sub 2}WO{sub 6}, AgBr, and Ag nanoparticles. The Ag@AgBr(20 wt.%)/Bi{sub 2}WO{sub 6} sample exhibited the best photocatalytic activity, degrading 95.03% MB after irradiation for 2 h, which was respectively 1.29 times and 1.28 times higher than that of Ag@AgBr and Bi{sub 2}WO{sub 6} photocatalyst. Meanwhile, phenol and salicylic acid were degraded to further prove the degradation ability of Ag@AgBr/Bi{sub 2

  15. Nanospherical composite of WO{sub 3} wrapped NaTaO{sub 3}: Improved photodegradation of tetracycline under visible light irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Qu, Lingnan; Lang, Junyu; Wang, Shuwei; Chai, Zhanli; Su, Yiguo; Wang, Xiaojing, E-mail: wang_xiao_jing@hotmail.com

    2016-12-01

    Graphical abstract: - Highlights: • A novel ternary NaTaO{sub 3}@WO{sub 3} photocatalyst was successfully fabricated. • NaTaO{sub 3}@WO{sub 3} composites exhibited spherical assemblies with fine WO{sub 3} nanosheets wrapped on the cube NaTaO{sub 3} nanoparticles. • NaTaO{sub 3}@WO{sub 3} showed the enhanced photocatalytic performance in the tetracycline hydrochloride degradation under visible light irradiation. • An adsorption−degradation photocatalytic mechanism promoted through a Z-type heterojunction was proposed. - Abstract: In this paper, WO{sub 3}-wrapped NaTaO{sub 3} nanospheres photocatalysts with different W/Ta molar ratios were successfully prepared via a facile hydrothermal method. The samples were characterized by X-ray diffraction, transmission and scan electron microscopy, X-ray photoelectron spectroscopy, FT-IR spectrum, UV−vis diffuse reflectance spectroscopy, and Barrett−Emmett−Teller technique. The photocatalytic activities for degrading tetracycline hydrochloride under visible light irradiation were examined. The results indicated that the as-prepared NaTaO{sub 3}@WO{sub 3} photocatalysts showed the obvious enhancement in the tetracycline hydrochloride degradation ratio, compared with the pure NaTaO{sub 3} and WO{sub 3} under visible light irradiation. The optimum percentage of NaTaO{sub 3}@WO{sub 3} composites with a 60.88% degradation rate was W:Ta = 0.3:1 in mole, which was mainly attributed to the effective separation of the photo-generated electron and hole as well as the expanding of the absorption edge to the visible region due to the spherical heterojunction by wrapping WO{sub 3} on the surface of NaTaO{sub 3}. The radicals trapping experiments demonstrated that there were multiple active species during the degrading process of TC. The possible mechanism of tetracycline hydrochloride degradation by NaTaO{sub 3}@WO{sub 3} composite was also proposed.

  16. Preparation and characterization of zinc and copper co-doped WO3 nanoparticles: Application in photocatalysis and photobiology.

    Science.gov (United States)

    Mohammadi, Sanaz; Sohrabi, Maryam; Golikand, Ahmad Nozad; Fakhri, Ali

    2016-08-01

    In this study, pure, Zn, Cu, Zn,Cu co-doped WO3 nanoparticles samples were prepared by precipitation and co-precipitation methods. These nanoparticles were characterized by field emission scanning electron microscopy (FE-SEM), X-ray diffraction (XRD), energy dispersive X-ray spectrometer (EDX), Dynamic light scattering (DLS), UV-visible and photoluminescence (PL) spectroscopy. The synthesized pure, Zn, Cu, Zn,Cu co-doped WO3 nanoparticles have smart optical properties and average sizes with 3.2, 3.12, 3.08 and 2.97eV of band-gap, 18.1, 23.2, 25.7 and 30.2nm, respectively. Photocatalytic activity of four nanoparticles was studying towards degradation of gentamicin antibiotic under ultraviolet and visible light irradiation. The result showed that Zn,Cu co-doped WO3 possessed high photocatalytic activity. The photocatalytic activity of WO3 nanoparticles could be remarkably increased by doping the Zn and Cu impurity. This can be attributed to the fact that the red shift of absorption edge and the trapping effect of the mono and co-doped WO3 nanoparticles. The research result presents a general and effective way to prepare different photocatalysts with enhanced visible and UV light-driven photocatalytic performance. Antibacterial activity of four different WO3 nanoparticles against Escherichia coli bacterium has been assessed by the agar disc method under light irradiation and dark medium. It is concluded from the present findings that WO3 nanoparticles can be used as an efficient antibacterial agent. Copyright © 2016 Elsevier B.V. All rights reserved.

  17. The effects of solvent on photocatalytic properties of Bi2WO6/TiO2 heterojunction under visible light irradiation

    Science.gov (United States)

    Guo, Qiyao; Huang, Yunfang; Xu, Hui; Luo, Dan; Huang, Feiyue; Gu, Lin; Wei, Yuelin; Zhao, Huang; Fan, Leqing; Wu, Jihuai

    2018-04-01

    Bi2WO6/TiO2 heterojunction photocatalysts with two different microstructures were controllably fabricated via a facile two-step synthetic route. XRD, XPS, SEM, TEM, BET-surface, DRS, PL spectra, photoelectrochemical measurement (Mott-Schottky), and zeta-potential analyzer were employed to clarify structural and morphological characteristics of the obtained products. The results showed that Bi2WO6 nanoparticles/nanosheets grew on the primary TiO2 nanorods. The TiO2 nanorods used as a synthetic template inhibit the growth of Bi2WO6 crystals along the c-axis, resulting in Bi2WO6/TiO2 heterostructure with one-dimensional (1D) morphology. The photocatalytic properties of Bi2WO6/TiO2 heterojunction photocatalysts were strongly dependent on their shapes and structures. Compared with bare Bi2WO6 and TiO2, Bi2WO6/TiO2 composite have stronger adsorption ability and better visible light photocatalytic activities towards organic dyes. The Bi2WO6/TiO2 composite prepared in EG solvent with optimal Bi:Ti ratio of 2:12 (S-TB2) showed the highest photocatalytic activity, which could totally decompose Rhodamine B within 10 min upon irradiation with visible light (λ > 422 nm), and retained the high photocatalytic performance after five recycles, confirming its stability and practical usability. The results of PL indicated that Bi2WO6 and TiO2 could combine well to form a heterojunction structure which facilitated electron-hole separation, and lead to the increasing photocatalytic activity.

  18. A comparative study of humidity sensing and photocatalytic applications of pure and nickel (Ni)-doped WO{sub 3} thin films

    Energy Technology Data Exchange (ETDEWEB)

    Ramkumar, S. [Bannari Amman Institute of Technology, Department of Physics, Erode, Tamilnadu (India); Rajarajan, G. [Vidhya Mandhir Institute of Technology, Department of Physics, Erode, Tamilnadu (India)

    2017-06-15

    Nanocrystalline of pristine and nickel (Ni)-doped tungsten trioxide (WO{sub 3}) thin films was deposited by chemical bath deposition method. The concentrations of Ni ions were varied from 0 to 10 wt%. In order to improve the crystallinity of the films were annealed at 600 C for 2 h in the ambient atmosphere. X-ray diffraction results reveal that the WO{sub 3} doped with nickel crystallizes in monoclinic structure and the results are in good agreement with the standard JCPDS data (card no: 83-0951). AFM micrographs reveal that average grain size of about 27-39 nm for pure and Ni-doped WO{sub 3} thin films. In addition, the band gap of the Ni-doped WO{sub 3} nanostructures is facilely tunable by controlling the Ni contents. The humidity sensor setup was fabricated and measured for pure and Ni-doped WO{sub 3} thin film sensor with various level of RH (10-90%). The Ni-doped WO{sub 3} sensor showed fast response and high sensitivity than pure WO{sub 3}. The photocatalytic activities of the films were evaluated by degradation of methyl orange, methylene blue and phenol in an aqueous solution under visible light irradiation. The photocatalytic activity of WO{sub 3} nanostructures could be remarkably enhanced by doping the Ni impurity. (orig.)

  19. Electrochromism and local order in amorphous WO/sub 3/

    Energy Technology Data Exchange (ETDEWEB)

    Zeller, H R; Beyeler, H U

    1977-06-01

    WO/sub 3/ films prepared under different conditions (evaporation, reactive sputtering and spraying of aqueous solutions of metatungstic acid) differ by orders of magnitude in their electrochromic sensitivity. Diffuse X-ray studies show the evaporated and sputtered films to be amorphous and to consists of a disordered network of corner sharing WO/sub 6/ octahedra. Sprayed films have different degrees of crystallinity depending on spraying conditions. From differential scanning calorimetry we conclude that the crystal water present in most films strongly affects the local order of the corner sharing octahedra. We find that crystal water not only provides a high ionic conductivity which is conditional for a fast electrochromic reaction but also stabilises electrocatalytically active surface sites for fast hydrogen or Li exchange with the adjacent electrolyte.

  20. Evaluate humidity sensing properties of novel TiO{sub 2}–WO{sub 3} composite material

    Energy Technology Data Exchange (ETDEWEB)

    Lin, Wang-De [Department of Applied Chemistry, Providence University, Taichung 43301 Taiwan, ROC (China); Department of Center for General Education, St. Mary' s Junior College of Medicine, Nursing and Management, Yilan 26644 Taiwan, ROC (China); Lai, De-Sheng; Chen, Min-Hung [Department of Applied Chemistry, Providence University, Taichung 43301 Taiwan, ROC (China); Wu, Ren-Jang, E-mail: rjwu@pu.edu.tw [Department of Applied Chemistry, Providence University, Taichung 43301 Taiwan, ROC (China); Chen, Fu-Chou [Department of Medical Research, Taichung Veterans General Hospital, Taichung 407, Taiwan, ROC (China)

    2013-10-15

    Graphical abstract: TiO{sub 2}–WO{sub 3} (1:1) showed better humidity sensing properties than others within the range of 12–90% relative humidity (RH), the response and recovery time were about 20 s and 160 s, respectively. Compared to the previous studies, the prepared sensor exhibits higher sensitivity (S = 451) and the low hysteresis value was around 0.13% at 32% RH. - Highlights: • Novel TiO{sub 2}–WO{sub 3} composite material was prepared for humidity sensor. • The sensor exhibits higher sensitivity (S = 451). • Low hysteresis value was around 0.13% at 32% RH. - Abstract: A novel TiO{sub 2}–WO{sub 3} composite material was prepared using a different proportion of TiO{sub 2} and WO{sub 3} to that investigated in previous studies. The obtained mesoporous material was characterized using X-ray diffraction, Fourier transform infrared spectrometry, transmission electron microscopy, energy dispersive X-ray spectroscopy, and N{sub 2} adsorption-desorption techniques. The humidity-sensing properties were measured using an inductance, capacitance and resistance analyzer. The results demonstrated that the TiO{sub 2}–WO{sub 3} sample with a ratio of 1:1 showed better humidity sensing properties. Compared to previous studies, the prepared sensor exhibited higher sensitivity (S = 451) and the lower hysteresis value was around 0.13% at 32% RH. Complex impedance analysis indicated that the enhanced humidity sensitivity was probably due to spherical Brunauer–Emmett–Teller surface area and the hetero-junction between TiO{sub 2}–WO{sub 3} thin films, while the impedance varied about three orders of magnitude. Our results demonstrated the potential application of TiO{sub 2}–WO{sub 3} composite for fabricating high performance humidity sensors.

  1. THE DISCOVERY OF A RARE WO-TYPE WOLF-RAYET STAR IN THE LARGE MAGELLANIC CLOUD

    Energy Technology Data Exchange (ETDEWEB)

    Neugent, Kathryn F.; Massey, Philip [Lowell Observatory, 1400 W Mars Hill Road, Flagstaff, AZ 86001 (United States); Morrell, Nidia, E-mail: kneugent@lowell.edu, E-mail: phil.massey@lowell.edu, E-mail: nmorrell@lco.cl [Las Campanas Observatory, Carnegie Observatories, Casilla 601, La Serena (Chile)

    2012-12-01

    While observing OB stars within the most crowded regions of the Large Magellanic Cloud, we happened upon a new Wolf-Rayet (WR) star in Lucke-Hodge 41, the rich OB association that contains S Doradus and numerous other massive stars. At first glance the spectrum resembled that of a WC4 star, but closer examination showed strong O VI {lambda}{lambda}3811, 34 lines, leading us to classify it as a WO4. This is only the second known WO in the LMC, and the first known WO4 (the other being a WO3). This rarity is to be expected due to these stars' short lifespans as they represent the most advanced evolutionary stage in a massive star's lifetime before exploding as supernovae. This discovery shows that while the majority of WRs within the LMC have been discovered, there may be a few WRs left to be found.

  2. Synthesis of ZnWO{sub 4} Electrode with tailored facets: Deactivating the Microorganisms through Photoelectrocatalytic methods

    Energy Technology Data Exchange (ETDEWEB)

    Zhan, Su [Department of Materials Science and Engineering, Dalian Maritime University, Dalian 116026 (China); Zhou, Feng, E-mail: zhoufeng99@mails.tsinghua.edu.cn [Department of Materials Science and Engineering, Dalian Maritime University, Dalian 116026 (China); Huang, Naibao; Liu, Yujun; He, Qiuchen; Tian, Yu; Yang, Yifan [Department of Materials Science and Engineering, Dalian Maritime University, Dalian 116026 (China); Ye, Fei [Department of Materials Science and Engineering, Dalian University of Technology, Dalian 116026 (China)

    2017-01-01

    Highlights: • ZnWO{sub 4} with different exposed facets was synthesized by the hydrothermal method. • The reactive facets were tailored by varying the solution pH. • The photoelectrocatalysis was more efficient in deactivating the microorganism. - Abstract: The exotic invasive species from the ballast water in the ship will bring about serious damages to ecosystem. Photocatalyst films have been widely studied for sterilization. In this study, ZnWO{sub 4} with different exposed facets was synthesized by hydrothermal method, and ZnWO{sub 4} film electrodes have been applied in ballast water treatment through the electro-assisted photocatalytic system. Then the samples were investigated by X-ray diffraction (XRD), X-ray photo-electron spectroscopy (XPS), Field emission on scanning electron microcopy (FE-SEM), Transmission electron microscopy (TEM), UV–vis diffuse reflectance spectroscopy (DRS), BET specific surface area analysis, Fourier transform infrared (FT-IR) and Electrochemical impedance spectra (EIS). ZnWO{sub 4} with an appropriate exposure of (0 1 1) facets ratio exhibited the best photocatalytic and photoelectrocatalytic activities. The microorganisms deactivated completely in 10 min by ZnWO{sub 4} films with 3 V bias. The mechanisms of (0 1 1) facets enhanced the photocatalytic and photoelectrocatalytic activities which were deduced based on the calculated result from the first principles. Simultaneously, appropriate exposed facets and applied bias could reduce the recombination of the photogenerated electron-hole pairs, and improve the photocatalytic activities of ZnWO{sub 4}.

  3. Structural, vibrational, and gasochromic properties of porous WO sub 3 films templated with a sol-gel organic-inorganic hybrid

    CERN Document Server

    Opara-Krasovec, U; Orel, B; Grdadolnik, J; Drazic, G

    2002-01-01

    The structure and the gasochromic properties of sol-gel-derived WO sub 3 films with a monoclinic structure (m-WO sub 3) were studied by focusing attention on the size of the monoclinic grains. The size of the m-WO sub 3 grains is modified by the addition of an organic-inorganic hybrid to the initial peroxopolytungstic acid (W-PTA) sols which are based on chemically bonded poly-(propylene glycol) to triethoxysilane end-capping groups (ICS-PPG). The results obtained with scanning electron microscopy (SEM) and transmission electron microscopy (TEM) show that the heat treatment (500 sup o C) of WO sub 3 /ICS- IPG (0.5, 1, 2, 5, and 10 mol%) composite films results in a change of their morphology, and nanodimensional pores are formed between the grains. High-resolution TEM (HRTEM) analysis revealed the presence of an amorphous phase on the outside of the m-WO sub 3 grains, whereas energy-dispersive x-ray spectra (EDXS) showed that this amorphous phase contained W and Si. Impregnation of the WO sub 3 /ICS-PPG film ...

  4. Synthesis of Bi2WO6 nanoparticles and its electrochemical properties in different electrolytes for pseudocapacitor electrodes

    International Nuclear Information System (INIS)

    Nithya, V.D.; Kalai Selvan, R.; Kalpana, D.; Vasylechko, Leonid; Sanjeeviraja, C.

    2013-01-01

    Highlights: • A simple, economical and environmentally benign sonochemical technique was utilized for the synthesis of homogeneous Bi 2 WO 6 nanoparticles. • This is the first attempt to employ Bi 2 WO 6 as a supercapacitor electrode material. • Effect of electrolyte on the capacitive behaviour of the material is studied. • Bi 2 WO 6 displays good capacitive behaviour in 1 M KOH compared with 1 M NaOH and 1 M LiOH and possess sufficient capacity retention. • It presented an energy density of 67 Wh/kg in the potential range from −0.9 V to 0.1 V and it would be a promising negative electrode for supercapacitor. -- Abstract: Nanosized Bi 2 WO 6 particles were successfully synthesized by sonochemical method with an objective to develop an inexpensive and eco-friendly electrode material for supercapacitors. The prepared material was subjected to various thermal, structural, morphological, compositional, electrical and electrochemical studies. Bi 2 WO 6 nanoparticle with homogeneous distribution was achieved through sonochemical process. The lattice parameter and atomic positions of Bi 2 WO 6 structure were refined through Reitveld analysis. The electrochemical performance of Bi 2 WO 6 nanoparticles was investigated in various aqueous electrolytes such as 1 M NaOH, 1 M LiOH, 1 M Na 2 SO 4 , 1 M KOH and 6 M KOH solutions. Among these, the material exhibited an enhanced electrochemical performance in KOH electrolyte due to its smaller hydration sphere radius, high ionic mobility and lower equivalent series resistance. The charge–discharge studies rendered a specific capacitance of 608 F/g in 1 M KOH at a current density of 0.5 mA/cm 2 . Bi 2 WO 6 exhibited an excellent coulombic efficiency and specific capacitance of around 304 F/g at 3 mA/cm 2 in the potential range from −0.9 to 0.1 V vs Hg/HgO in 1 M KOH electrolyte. The above results assured that Bi 2 WO 6 could be utilized as suitable negative electrode material for supercapacitor applications and 1 M

  5. CTAB-Assisted Hydrothermal Synthesis of WO3 Hierarchical Porous Structures and Investigation of Their Sensing Properties

    Directory of Open Access Journals (Sweden)

    Dan Meng

    2015-01-01

    Full Text Available WO3 hierarchical porous structures were successfully synthesized via cetyltrimethylammonium bromide- (CTAB- assisted hydrothermal method. The structure and morphology were investigated using scanning electron microscope, X-ray diffractometer, transmission electron microscopy, X-ray photoelectron spectra, Brunauer-Emmett-Teller nitrogen adsorption-desorption, and thermogravimetry and differential thermal analysis. The result demonstrated that WO3 hierarchical porous structures with an orthorhombic structure were constructed by a number of nanoparticles about 50–100 nm in diameters. The H2 gas sensing measurements showed that well-defined WO3 hierarchical porous structures with a large specific surface area exhibited the higher sensitivity compared with products without CTAB at all operating temperatures. Moreover, the reversible and fast response to H2 gas and good selectivity were obtained. The results indicated that the WO3 hierarchical porous structures are promising materials for gas sensors.

  6. Phase modification and surface plasmon resonance of Au/WO{sub 3} system

    Energy Technology Data Exchange (ETDEWEB)

    Bose, R. Jolly; Kavitha, V.S. [Department of Optoelectronics, University of Kerala, Kariyavattom, Thiruvananthapuram 691574, Kerala (India); Sudarsanakumar, C. [School of Pure and Applied Physics, Mahatma Gandhi University, Priyadarshini Hills, Kottayam 686560, Kerala (India); Pillai, V.P. Mahadevan, E-mail: vpmpillai9@gmail.com [Department of Optoelectronics, University of Kerala, Kariyavattom, Thiruvananthapuram 691574, Kerala (India)

    2016-08-30

    Highlights: • We have investigated the role of gold as catalyst and nucleation centers, for the crystallization and phase modification of tungsten oxide, in Au/WO{sub 3} matrix. • The phase change from triclinic WO{sub 3} to monoclinic W{sub 18}O{sub 49} is found to enhance with gold incorporation. • The surface plasmon resonance is observed in gold/tungsten oxide system with the appearance of an absorption band near the wavelength 604 nm. - Abstract: We report the action of gold as catalyst for the modification of phase from triclinic WO{sub 3} to monoclinic W{sub 18}O{sub 49} and nucleation centre for the formation of W{sub 18}O{sub 49} phase, in gold incorporated tungsten oxide films prepared by RF magnetron sputtering technique. A new band is observed near 925 cm{sup −1} in the Raman spectra of gold incorporated tungsten oxide films which is not observed in the pure tungsten oxide film. The intensity of this band enhances with gold content. A localized surface plasmon resonance (LSPR) band is observed near the wavelength 604 nm in gold incorporated tungsten oxide films. The integrated intensities of LSPR band and Raman band (∼925 cm{sup −1}) can be used for sensing the quantity of gold in the Au/WO{sub 3} matrix.

  7. TRANSPARENT CONCRETE

    OpenAIRE

    Sandeep Sharma*, Dr. O.P. Reddy

    2017-01-01

    Transparent concrete is the new type of concrete introduced in todays world which carries special property of light transmitting due to presence of light Optical fibres. Which is also known as translucent concrete or light transmitting concrete, it is achieved by replacing coarse aggregates with transparent alternate materials (Optical fibres). The binding material in transparent concrete may be able to transmit light by using clear resins the concrete mix. The concrete used in industry in pr...

  8. Exfoliated thin Bi{sub 2}MoO{sub 6} nanosheets supported on WO{sub 3} electrode for enhanced photoelectrochemical water splitting

    Energy Technology Data Exchange (ETDEWEB)

    Ma, Ying; Jia, Yulong; Wang, Lina [State Key Laboratory for Oxo Synthesis & Selective Oxidation, and National Engineering Research Center for Fine Petrochemical Intermediates, Lanzhou Institute of Chemical Physics, CAS, Lanzhou 730000 (China); University of Chinese Academy of Sciences, Beijing 100049 (China); Yang, Min [State Key Laboratory for Oxo Synthesis & Selective Oxidation, and National Engineering Research Center for Fine Petrochemical Intermediates, Lanzhou Institute of Chemical Physics, CAS, Lanzhou 730000 (China); Bi, Yingpu, E-mail: yingpubi@licp.cas.cn [State Key Laboratory for Oxo Synthesis & Selective Oxidation, and National Engineering Research Center for Fine Petrochemical Intermediates, Lanzhou Institute of Chemical Physics, CAS, Lanzhou 730000 (China); Qi, Yanxing, E-mail: qiyx@licp.cas.cn [State Key Laboratory for Oxo Synthesis & Selective Oxidation, and National Engineering Research Center for Fine Petrochemical Intermediates, Lanzhou Institute of Chemical Physics, CAS, Lanzhou 730000 (China)

    2016-12-30

    Highlights: • Thin Bi{sub 2}MoO{sub 6} nanosheets were prepared by microwave assisted ultrasonic separation. • The thin Bi{sub 2}MoO{sub 6} nanosheets could be more favorable to charge shift and separation. • The WO{sub 3}/thin Bi{sub 2}MoO{sub 6} exhibits superior photoelectric activity than WO{sub 3}/Bi{sub 2}MoO{sub 6} film. • The efficient photoelectric property results from facilitated charge separation. - Abstract: Thin Bi{sub 2}MoO{sub 6} nanosheets are obtained by a microwave-assisted ultrasonic separation process. After exfoliation, the thinner and uniform nanosheets with a thickness of about 10 nm were obtained. The exfoliated nanosheets would provide many amazing functionalities such as high electron mobility and quantum Hall effects. Therefore, thin Bi{sub 2}MoO{sub 6} supported on WO{sub 3} electrode (WO{sub 3}/thin Bi{sub 2}MoO{sub 6}) exhibits facilitated charge separation than pure WO{sub 3} film and the un-exfoliated Bi{sub 2}MoO{sub 6} nanosheets supported on WO{sub 3} electrode (WO{sub 3}/Bi{sub 2}MoO{sub 6}). As a result, WO{sub 3}/thin Bi{sub 2}MoO{sub 6} shows remarkably stable photocurrent density of 2.2 mA/cm{sup 2} at 0.8 V{sub SCE} in 0.1 M Na{sub 2}SO{sub 4} which is higher than that of that of WO{sub 3} (1.1 mA/cm{sup 2}) and WO{sub 3}/Bi{sub 2}MoO{sub 6} (1.5 mA/cm{sup 2}).

  9. Hydrogenation of carbon monoxide on WO/sub 3/-Supported ruthenium catalysts

    Energy Technology Data Exchange (ETDEWEB)

    Yoshinari, Tomohiro; Suganuma, Fujio; Sera, Chikara

    1988-01-01

    In this study, a WO/sub 3/-supported catalyst was prepared to conduct hydrogenation of CO for examining the product distribution and composition of hydrocarbons, using a gamma-alumina-supported catalyst for comparison. These catalysts were used under pressure to conduct a distributive reaction and the desorbing behavior of CO or H/sub 2/ at elevated temperature was measured to examine the influence of the type of carrier or the method of preparation on the activity and the distribution of products formed. The WO/sub 3/-supported catalyst gave a carbon chain length distribution that did not comply with the rule of Schulz-Flory, giving a composition richer in the isomers. Carbon number distribution is affected by Ru-dispersion, and the selectivity of isomers depends on the acidity of the carrier. Formed products distribution of the WO/sub 3/-supported reaction is attributable to the secondary reaction, which relates to the acidic point of the carrier, of the primary product formed on the metal. (7 figs, 4 tabs, 18 refs)

  10. Preparation and optimization of CdWO{sub 4}-polymer nano-composite film as an alpha particle counter

    Energy Technology Data Exchange (ETDEWEB)

    Ziluei, Hossein [Nuclear Science and Technology Research Institute, AEOI, Tehran (Iran, Islamic Republic of); Azimirad, Rouhollah [Malek-Ashtar University of Technology, Tehran (Iran, Islamic Republic of); Mojtahedzadeh Larijani, Majid, E-mail: mmojtahedfr@yahoo.com [Nuclear Science and Technology Research Institute, AEOI, Tehran (Iran, Islamic Republic of); Ziaie, Farhoud [Nuclear Science and Technology Research Institute, AEOI, Tehran (Iran, Islamic Republic of)

    2017-04-21

    In this research work, CdWO{sub 4}/polymer composite films with different thicknesses were prepared using Poly-methyl acrylate polymer and synthesized CdWO{sub 4} powder. The CdWO{sub 4} powder was synthesized by a simple co-precipitation method in the laboratory. X-ray diffraction, photoluminescence, Fourier transformed infrared spectroscopy and energy-dispersive X-ray spectroscopy proved that the CdWO{sub 4} powder was successfully prepared. Moreover, photoluminescence analysis showed that adding polymer does not change the emission peak of CdWO{sub 4}. Also, the responses of all samples were measured using an {sup 241}Am alpha source with 1860 Bq activity. Results showed that the sample having thickness of 177 mg/cm{sup 2} has the best counting efficiency (over 2π geometry) among the others. The efficiency measurement was further evaluated using a {sup 230}Th source whose activity is 190.7 Bq. It revealed that the counting efficiency of this sample for both {sup 241}Am and {sup 230}Th was nearly equal.

  11. Thermorewritable card by using dyes; Senryo wo mochiita kakikae kanona card

    Energy Technology Data Exchange (ETDEWEB)

    Muto, Y.

    1998-06-01

    Described herein are thermorewritable cards which use dyes. Rewritable cards, mainly used for membership and point cards, are themselves used repeatedly and required to be rewritable repeatedly for information they carry. The dyes and developers used for the conventional heat- and pressure-sensitive papers are colorless, leuco-dye precursors and acidic compounds with a phenolic hydroxyl group or the like. They transfer electrons to each other, opening the lactone ring of the dye precursor to develop the color. Developing and erasing the color are reversible chemical reactions, where the color is developed under heat and maintained by quenching. For erasing the color, it is heated and then slowly cooled to separate the precursor and developer phases from each other. A printer (thermal head) is required for developing and erasing a color. Durability under various conditions is another requirement of the card; it must be adaptable to weather conditions and resistant to sweat. The new thermorewritable card is protected from various adverse effects on its chemical reactions, and made as durable as the conventional cards. 3 refs., 5 figs., 1 tab.

  12. Luminescence and thermoluminescence properties of Sr{sub 3}WO{sub 6}:Eu{sup 3+} phosphor

    Energy Technology Data Exchange (ETDEWEB)

    Emen, F.M., E-mail: femen106@gmail.com [Department of Chemistry, Faculty of Arts and Science, Mehmet Akif Ersoy University, TR 15030, Burdur (Turkey); Altinkaya, R. [Department of Chemistry, Faculty of Arts and Science, Mersin University, TR 33343, Mersin (Turkey)

    2013-02-15

    Sr{sub 3-x}WO{sub 6}:xEu{sup 3+} (x varies from 0.01 to 0.06) phosphors have been prepared at high temperature by the solid-state method. The crystal structure of Sr{sub 2.95}WO{sub 6}:0.05Eu{sup 3+} phosphor has been determined as a triclinic P-1 space group with a=8.3608 (19) A, b=8.2903 (24) A, c=8.2145 (23) A, {alpha}=89.79 (3){sup Degree-Sign }, {beta}=89.82 (3){sup Degree-Sign }, and {gamma}=89.753 (22){sup Degree-Sign }. The excitation spectrum of Sr{sub 2.95}WO{sub 6}:0.05Eu{sup 3+} phosphor reveals five excitation bands: one is assigned to the charge-transfer (CTLM) band of Sr{sub 3}WO{sub 6} host at 307 nm, and another is assigned to intra-4f transitions between 393 nm and 600 nm. The emission spectrum of Sr{sub 2.95}WO{sub 6}:0.05Eu{sup 3+} phosphor exhibits a series of emission bands, which are attributed to the {sup 5}D{sub 0}{yields}{sup 7}F{sub j} (j=0-4) transitions of Eu{sup 3+} ions. The luminescence studies revealed that the Eu{sup 3+} ions show high luminescent efficiency in emitting red light at 616 nm. The thermoluminescence glow curve shows one dominant glow peak observed at 56 Degree-Sign C which is related to the defects at shallow trap depth. The trap parameters mainly activation energy (E{sub a}) and the order of the kinetics (b) were evaluated by using Rasheedy's three points method (TPM). - Highlights: Black-Right-Pointing-Pointer The Sr{sub 3}WO{sub 6}:Eu{sup 3+} phosphor was prepared by using conventional ceramic method. Black-Right-Pointing-Pointer The diffraction peaks of phosphor have been indexed to triclinic system. Black-Right-Pointing-Pointer The emission peak at 616 nm belongs to {sup 5}D{sub 0}{yields}{sup 7}F{sub 2} electric dipole transitions of Eu{sup 3+}. Black-Right-Pointing-Pointer The emission band of WO{sub 6} and excitation bands of Eu{sup 3+} are overlapping each other. Black-Right-Pointing-Pointer The energy transfer from WO{sub 6} groups to the Eu{sup 3+} ions occurs under the UV excitation.

  13. Relevance of Wnt10b and activation of β-catenin/GCMa/syncytin-1 pathway in BeWo cell fusion.

    Science.gov (United States)

    Malhotra, Sudha Saryu; Banerjee, Priyanka; Chaudhary, Piyush; Pal, Rahul; Gupta, Satish Kumar

    2017-10-01

    To study the involvement of specific Wnt(s) ligand during trophoblastic BeWo cell differentiation. BeWo cells on treatment with forskolin/human chorionic gonadotropin (hCG) were studied for cell fusion by desmoplakin I+II staining and/or hCG secretion by ELISA. Levels of Wnt10b/β-catenin/glial cell missing a (GCMa)/syncytin-1 were studied by qPCR/Western blotting in forskolin-/hCG-treated control siRNA and Wnt10b silenced BeWo cells. BeWo cells on treatment with hCG (5 IU/mL) led to a 94-fold increase in Wnt10b transcript. Wnt10b silencing showed significant decrease in forskolin-/hCG-mediated BeWo cell fusion and/or hCG secretion. It led to down-regulation of β-catenin (nuclear and cytoplasmic), GCMa and syncytin-1 expression. Treatment of BeWo cells with H89, protein kinase A (PKA) signaling inhibitor, significantly reduced forskolin-/hCG-induced Wnt10b, β-catenin, and syncytin-1 expression, which also resulted in reduced cell fusion. Wnt10b is involved in forskolin/hCG-mediated BeWo cell fusion via β-catenin/GCMa/syncytin pathway, which may also involve activation of PKA. © 2017 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

  14. Surface Functionalization of WO3 Thin Films with (3-Aminopropyl)triethoxysilane and Succinic Anhydride

    Science.gov (United States)

    Ta, Thi Kieu Hanh; Tran, Thi Nhu Hoa; Tran, Quang Minh Nhat; Pham, Duy Phong; Pham, Kim Ngoc; Cao, Thi Thanh; Kim, Yong Soo; Tran, Dai Lam; Ju, Heongkyu; Phan, Bach Thang

    2017-06-01

    We report effects of oxygen plasma treatment on the surface functionalization of WO3 thin films with (3-aminopropyl)triethoxysilane (APTES) and succinic anhydride (SA). X-ray diffraction and x-ray photoelectron spectroscopy results indicate the existence of the WO3 phase. Fourier transform infrared spectroscopy measurement shows clear bands at 1040 cm-1 (Si-O-Si), 1556 cm-1 (N-H), 1655 cm-1 (C=O), 2937 cm-1 (C-H) and 3298 cm-1 (N-H), confirming the surface functionalization efficiency enhanced by prior treatment of oxygen plasma. It thus follows that the prior oxygen plasma treatment activates hydroxylation with more -OH groups on the WO3 surface, which can pave a highly efficient way to the surface functionalization by APTES and SA.

  15. Synthesis and characterizations of isolated WO{sub 4} anchored on mesoporous TiTUD-1 support

    Energy Technology Data Exchange (ETDEWEB)

    Pachamuthu, Muthusamy P. [Department of Chemistry, Bannari Amman Institute of Technology, Sathyamangalam, Erode, 638401 (India); Maheswari, Rajamanickam [Center for Environmentally Beneficial Catalysis (CEBC), The University of Kansas, Lawrence, KS, 66047 (United States); Ramanathan, Anand, E-mail: anand@ku.edu [Center for Environmentally Beneficial Catalysis (CEBC), The University of Kansas, Lawrence, KS, 66047 (United States)

    2017-04-30

    Highlights: • Incorporation of (WO{sub 4}{sup 2−}) species into amorphous mesoporous silicate TiTUD-1. • Typical TUD-1 structure with dispersed Ti{sup 4+} and WO{sub 4}{sup 2−} species. • FT Raman and XPS results evidenced the WO{sub 4}{sup 2−} species dispersion. • Catalyst with 20% W loading yields higher conversion in esterification reaction. - Abstract: The titanium incorporated mesoporous silicate TUD-1 (Si/Ti ratio 40) was synthesized by non-surfactant route, and utilized as a support for tungstate (WO{sub 4}{sup 2−}) species with variable loading (5–30 wt%). The structural and textural properties of these samples were evaluated from X-ray diffraction (XRD) and N{sub 2} physisorption studies. Diffuse reflectance UV–vis (DR UV–vis), Fourier transform infrared (FTIR), Fourier transform Raman (FT Raman) spectra evidenced the Ti{sup 4+} coordination and the formation of WO{sub 4}{sup 2−} species, further supported by X-ray photoelectron spectroscopy (XPS) studies. Scanning electron microscope–energy dispersive X-ray analysis (SEM-EDAX), High resolution transmission electron microscope (HRTEM) further support the materials morphology corroborating other characterizations. The catalytic activities of these materials were tested in the liquid phase, solvent free esterification of acetic acid with n-butanol. About 95% of acetic acid conversion resulted by these catalysts with 8 h of reaction time.

  16. How Concrete is Concrete

    Directory of Open Access Journals (Sweden)

    Koeno Gravemeijer

    2010-07-01

    Full Text Available If we want to make something concrete in mathematics education, we are inclined introduce, what we call, ‘manipulatives’, in the form of tactile objects or visual representations. If we want to make something concrete in a everyday-life conversation, we look for an example. In the former, we try to make a concrete model of our own, abstract, knowledge; in the latter, we try to find an example that the others will be familiar with. This article first looks at the tension between these two different ways of making things concrete. Next another role of manipulatives, will be discussed, namely that of means for scaffolding and communication. In this role, manipulatives may function as means of support in a process that aims at helping students to build on their own thinking while constructing more sophisticated mathematics

  17. Solar photocatalytic activity of TiO{sub 2} modified with WO{sub 3} on the degradation of an organophosphorus pesticide

    Energy Technology Data Exchange (ETDEWEB)

    Ramos-Delgado, N.A. [Universidad Autónoma de Nuevo León, Facultad de Ciencias Químicas, San Nicolás de los Garza, N.L. (Mexico); Gracia-Pinilla, M.A. [Universidad Autónoma de Nuevo León, Facultad de Ciencias Físico-Matemáticas, Av. Universidad, Cd. Universitaria, San Nicolás de los Garza, N.L. (Mexico); Universidad Autónoma de Nuevo León, Centro de Investigación e Innovación en Desarrollo de Ingeniería y Tecnología, PIIT Km 6, Carretera al Aeropuerto, Apodaca, N.L. (Mexico); Maya-Treviño, L.; Hinojosa-Reyes, L.; Guzman-Mar, J.L. [Universidad Autónoma de Nuevo León, Facultad de Ciencias Químicas, San Nicolás de los Garza, N.L. (Mexico); Hernández-Ramírez, A., E-mail: aracely.hernandezrm@uanl.edu.mx [Universidad Autónoma de Nuevo León, Facultad de Ciencias Químicas, San Nicolás de los Garza, N.L. (Mexico)

    2013-12-15

    Highlights: • TiO{sub 2} and WO{sub 3}/TiO{sub 2} (2 and 5%) were tested in the photocatalytic malathion degradation. • The use of solar radiation in the photocatalytic degradation process was evaluated. • Modified catalyst showed greater photocatalytic activity than pure TiO{sub 2}. • The mineralization rate was improved when WO{sub 3} content on TiO{sub 2} was 2%. -- Abstract: In this study, the solar photocatalytic activity (SPA) of WO{sub 3}/TiO{sub 2} photocatalysts synthesized by the sol–gel method with two different percentages of WO{sub 3} (2 and 5%wt) was evaluated using malathion as a model contaminant. For comparative purpose bare TiO{sub 2} was also prepared by sol–gel process. The powders were characterized by X-ray diffraction (XRD), Raman spectroscopy, diffuse reflectance UV–vis spectroscopy (DRUV–vis), specific surface area by the BET method (SSA{sub BET}), scanning electron microscopy (SEM), high resolution transmission electron microscopy (HRTEM) and scanning transmission electron microscopy with a high annular angle dark field detector (STEM-HAADF). The XRD, Raman, HRTEM and STEM-HAADF analyses indicated that WO{sub 3} was present as a monoclinic crystalline phase with nanometric cluster sizes (1.1 ± 0.1 nm for 2% WO{sub 3}/TiO{sub 2} and 1.35 ± 0.3 nm for 5% WO{sub 3}/TiO{sub 2}) and uniformly dispersed on the surface of TiO{sub 2}. The particle size of the materials was 19.4 ± 3.3 nm and 25.6 ± 3 nm for 2% and 5% WO{sub 3}/TiO{sub 2}, respectively. The SPA was evaluated on the degradation of commercial malathion pesticide using natural solar light. The 2% WO{sub 3}/TiO{sub 2} photocatalyst exhibited the best photocatalytic activity achieving 76% of total organic carbon (TOC) abatement after 300 min compared to the 5% WO{sub 3}/TiO{sub 2} and bare TiO{sub 2} photocatalysts, which achieved 28 and 47% mineralization, respectively. Finally, experiments were performed to assess 2% WO{sub 3}/TiO{sub 2} catalyst activity on

  18. Preparation and photoelectric properties of p-CaFe{sub 2}O{sub 4}/n-WO{sub 3} composites

    Energy Technology Data Exchange (ETDEWEB)

    Wan, Ruiqin; Jia, Caihong [Key Laboratory of Photovoltaic Materials of Henan Province and School of Physics and Electronics, Henan University, Kaifeng 475004 (China); Zhang, Weifeng, E-mail: wfzhang@henu.edu.cn [Key Laboratory of Photovoltaic Materials of Henan Province and School of Physics and Electronics, Henan University, Kaifeng 475004 (China)

    2012-12-15

    Highlights: Black-Right-Pointing-Pointer Surface photovoltage spectroscopy investigation on p-CaFe{sub 2}O{sub 4}/n-WO{sub 3} composites. Black-Right-Pointing-Pointer The photovoltaic response is enhanced in p-CaFe{sub 2}O{sub 4}/n-WO{sub 3} composites. Black-Right-Pointing-Pointer The multielectron process and high rate of carrier migration in WO{sub 3}. - Abstract: Composites of p-CaFe{sub 2}O{sub 4}/n-WO{sub 3} are prepared via a sol-gel technique. Their structures and optical properties are characterized with X-ray diffraction, scanning electron microscopy and UV-vis absorption spectroscopy. The photoelectric characteristics are investigated by surface photovoltage spectroscopy combined with electric field induced surface photovoltage spectroscopy. The results indicate that CaFe{sub 2}O{sub 4} can well form a p-n type composite with WO{sub 3}, and the intensity and spectral region of surface photovoltaic response for the composites are strongly dependent on the molar ratio of two components. The enhancement in photoelectric properties and the effective separation of photogenerated carriers could be attributed to the energy level matching between the two components, multielectron process and the high migration rate in WO{sub 3}.

  19. How Concrete is Concrete

    OpenAIRE

    Koeno Gravemeijer

    2010-01-01

    If we want to make something concrete in mathematics education, we are inclined introduce, what we call, ‘manipulatives’, in the form of tactile objects or visual representations. If we want to make something concrete in a everyday-life conversation, we look for an example. In the former, we try to make a concrete model of our own, abstract, knowledge; in the latter, we try to find an example that the others will be familiar with. This article first looks at the tension between these two diff...

  20. Effect of insulating concrete forms in concrete compresive strength

    Science.gov (United States)

    Martinez Jerez, Silvio R.

    The subject presented in this thesis is the effect of Insulating Concrete Forms (ICF's) on concrete compressive strength. This work seeks to identify if concrete cured in ICF's has an effect in compressive strength due to the thermal insulation provided by the forms. Modern construction is moving to energy efficient buildings and ICF's is becoming more popular in new developments. The thesis used a concrete mixture and a mortar mixture to investigate the effects of ICF's on concrete compressive strength. After the experimentations were performed, it was concluded that the ICF's do affect concrete strength. It was found that the forms increase concrete strength without the need for additional curing water. An increase of 50% in strength at 56 days was obtained. It was concluded that the longer concrete cures inside ICF's, the higher strength it reaches, and that ICF's effect on concrete strength is proportional to volume of concrete.

  1. Photothermal ablation cancer therapy using homogeneous CsxWO3 nanorods with broad near-infra-red absorption

    Science.gov (United States)

    Guo, Chongshen; Yin, Shu; Yu, Haijun; Liu, Shaoqin; Dong, Qiang; Goto, Takehiro; Zhang, Zhiwen; Li, Yaping; Sato, Tsugio

    2013-06-01

    Recently, photothermal ablation therapy (PTA) employing near-infrared radiation (NIR) has been extensively investigated as an emerging modality for cancer management. However, the clinical translation of this promising approach is limited by the lack of PTA agents with broad NIR absorption, low cost and high photothermal conversion efficiency. Herein, we have developed PEGylated homogeneous CsxWO3 nanorods (a mean size ~69.3 nm × 12.8 nm) with broad photo-absorption (780-2500 nm) as a novel NIR absorbent for PTA treatment of human cancer. The prepared CsxWO3 nanocrystals displayed strong near-infrared optical absorption with a high molar extinction coefficient (e.g. 4.8 × 1010 M-1 cm-1 at 980 nm), thus generated significant amounts of heat upon excitation with near-infrared light. The PTA study in two human carcinoma cell lines (i.e. A549 lung cancer cells and HeLa ovarian cancer cells) demonstrated that CsxWO3 nanorods can efficiently cause cell death via hyperthermia induced lysosome destruction, cytoskeleton protein degradation, DNA damage and thereafter cellular necrosis or apoptosis. Our study also confirmed the migration of healthy cells migrated from unirradiated areas to dead cell cycle, which is essential for tissue reconstruction and wound healing after photodestruction of tumor tissue. The prompted results reported in the current study imply the promising potential of CsxWO3 nanorods for application in PTA cancer therapy.Recently, photothermal ablation therapy (PTA) employing near-infrared radiation (NIR) has been extensively investigated as an emerging modality for cancer management. However, the clinical translation of this promising approach is limited by the lack of PTA agents with broad NIR absorption, low cost and high photothermal conversion efficiency. Herein, we have developed PEGylated homogeneous CsxWO3 nanorods (a mean size ~69.3 nm × 12.8 nm) with broad photo-absorption (780-2500 nm) as a novel NIR absorbent for PTA treatment of human

  2. Rare-earth-ion doped KY(WO4)2 optical waveguides grown by liquid-phase epitaxy

    NARCIS (Netherlands)

    Romanyuk, Y.E.; Apostolopoulos, V.; Utke, U.; Pollnau, Markus

    High-quality KY(WO4)2 thin layers doped with rare-earth-ions were grown using liquid-phase epitaxy. A low-temperature mixture of chlorides was used as the flux and undoped KY(WO4)2 crystals as substrates. The crystalline layers possessed thicknesses up to 10 µm. Passive and active planar waveguiding

  3. Luminescence and photo-thermally stimulated defects creation processes in PbWO{sub 4} crystals doped with trivalent rare-earth ions

    Energy Technology Data Exchange (ETDEWEB)

    Fabeni, P. [Institute of Applied Physics “N.Carrara” (IFAC) of CNR, Via Madonna del Piano 10, 50019 Sesto Fiorentino (Firenze) (Italy); Krasnikov, A.; Kärner, T. [Institute of Physics, University of Tartu, Riia 142, 51014 Tartu (Estonia); Laguta, V.V.; Nikl, M. [Institute of Physics AS CR, Cukrovarnicka 10, 16253 Prague (Czech Republic); Pazzi, G.P. [Institute of Applied Physics “N.Carrara” (IFAC) of CNR, Via Madonna del Piano 10, 50019 Sesto Fiorentino (Firenze) (Italy); Zazubovich, S., E-mail: svet@fi.tartu.ee [Institute of Physics, University of Tartu, Riia 142, 51014 Tartu (Estonia)

    2013-04-15

    In PbWO{sub 4} crystals, doped with various trivalent rare-earth A{sup 3+} ions (A{sup 3+}: La{sup 3+}, Lu{sup 3+}, Y{sup 3+}, Ce{sup 3+}, Gd{sup 3+}), electron (WO{sub 4}){sup 3−} and {(WO_4)"3"−–A"3"+} centers can be created under UV irradiation not only in the host absorption region but also in the energy range around 3.85 eV (Böhm et al., 1999; Krasnikov et al., 2010). Under excitation in the same energy range, the UV emission peak at 3.05–3.20 eV is observed. In the present work, the origin of this emission is investigated in detail by low-temperature time-resolved luminescence methods. Photo-thermally stimulated creation of (WO{sub 4}){sup 3−} and {(WO_4)"3"−–A"3"+} centers is studied also in PbWO{sub 4}:Mo,A{sup 3+} crystals. Various processes, which could explain both the appearance of the UV emission and the creation of the {(WO_4)"3"−–A"3"+}-type centers under irradiation of PbWO{sub 4}: A{sup 3+} crystals in the 3.85±0.35 eV energy range, are discussed. The radiative and non-radiative decay of the excitons localized near A{sup 3+} ions is considered as the most probable mechanism to explain the observed features. -- Highlights: ► UV emission of PbWO{sub 4}: A{sup 3+} (A{sup 3+}: La{sup 3+}, Lu{sup 3+}, Y{sup 3+}, Ce{sup 3+}, and Gd{sup 3+}) crystals is studied. ► The emission is ascribed to the radiative decay of excitons localized near A{sup 3+} ions. ► The excitons are created at 3.85 eV excitation by a two-step process. ► Non-radiative decay of the excitons leads to the creation of (WO{sub 4}){sup 3−}–A{sup 3+} centers.

  4. Hydrothermal synthesis of CdWO nanorods and their ...

    African Journals Online (AJOL)

    NICO

    CdWO4 has a high refractive index, a high X-ray absorption coefficient, low radiation damage, high luminescence intensity and low afterglow to .... atomic number ratio of the elements of Cd, W and O is approxi- mately 1:1:4 and is consistent ...

  5. Performance analysis of CRF-based learning for processing WoT application requests expressed in natural language.

    Science.gov (United States)

    Yoon, Young

    2016-01-01

    In this paper, we investigate the effectiveness of a CRF-based learning method for identifying necessary Web of Things (WoT) application components that would satisfy the users' requests issued in natural language. For instance, a user request such as "archive all sports breaking news" can be satisfied by composing a WoT application that consists of ESPN breaking news service and Dropbox as a storage service. We built an engine that can identify the necessary application components by recognizing a main act (MA) or named entities (NEs) from a given request. We trained this engine with the descriptions of WoT applications (called recipes) that were collected from IFTTT WoT platform. IFTTT hosts over 300 WoT entities that offer thousands of functions referred to as triggers and actions. There are more than 270,000 publicly-available recipes composed with those functions by real users. Therefore, the set of these recipes is well-qualified for the training of our MA and NE recognition engine. We share our unique experience of generating the training and test set from these recipe descriptions and assess the performance of the CRF-based language method. Based on the performance evaluation, we introduce further research directions.

  6. Effect of Post-annealing on the Electrochromic Properties of Layer-by-Layer Arrangement FTO-WO3-Ag-WO3-Ag

    Science.gov (United States)

    Hoseinzadeh, S.; Ghasemiasl, R.; Bahari, A.; Ramezani, A. H.

    2018-03-01

    In the current study, composites of tungsten trioxide (W03) and silver (Ag) are deposited in a layer-by-layer electrochromic (EC) arrangement onto a fluorine-doped tin oxide coated glass substrate. Tungsten oxide nanoparticles are an n-type semiconductor that can be used as EC cathode material. Nano-sized silver is a metal that can serve as an electron trap center that facilitates charge departure. In this method, the WO3 and Ag nanoparticle powder were deposited by physical vapor deposition onto the glass substrate. The fabricated electrochromic devices (ECD) were post-annealed to examine the effect of temperature on their EC properties. The morphology of the thin film was characterized by scanning electron microscopy and atomic force microscopy. Structural analysis showed that the addition of silver dopant increased the size of the aggregation of the film. The film had an average approximate roughness of about 17.8 nm. The electro-optical properties of the thin film were investigated using cyclic voltammetry and UV-visible spectroscopy to compare the effects of different post-annealing temperatures. The ECD showed that annealing at 200°C provided better conductivity (maximum current of about 90 mA in the oxidation state) and change of transmittance (ΔT = 90% at the continuous switching step) than did the other thin films. The optical band gaps of the thin film showed that it allowed direct transition at 3.85 eV. The EC properties of these combinations of coloration efficiency and response time indicate that the WO3-Ag-WO3-Ag arrangement is a promising candidate for use in such ECDs.

  7. Photoluminescence characteristics of Sm{sup 3+}-doped Ba{sub 2}CaWO{sub 6} as new orange–red emitting phosphors

    Energy Technology Data Exchange (ETDEWEB)

    Yu, Ruiijn [College of Science, Northwest A and F University, Yangling, Shaanxi 712100 (China); Department of Physics, Pukyong National University, Busan 608-737 (Korea, Republic of); Department of Physics, Changwon National University, Changwon 641-773 (Korea, Republic of); Mi Noh, Hyeon; Kee Moon, Byung; Chun Choi, Byung [Department of Physics, Pukyong National University, Busan 608-737 (Korea, Republic of); Hyun Jeong, Jung, E-mail: jhjeong@pknu.ac.kr [Department of Physics, Pukyong National University, Busan 608-737 (Korea, Republic of); Sueb Lee, Ho [Department of Physics, Changwon National University, Changwon 641-773 (Korea, Republic of); Jang, Kiwan, E-mail: kwjang@changwon.ac.kr [Department of Physics, Changwon National University, Changwon 641-773 (Korea, Republic of); Soo Yi, Soung [Department of Electronic Material Engineering, Silla University, Busan 617-736 (Korea, Republic of)

    2014-08-01

    The orange–red emitting Ba{sub 2}CaWO{sub 6}:xSm{sup 3+} (0.01≤x≤0.25) phosphors were synthesized via solid state reaction process. The crystal structure of the phosphor was characterized by XRD. The photoluminescence excitation and emission spectra, concentration effect were investigated. The results show an efficient energy transfer from WO{sub 6}{sup 6−} group to Sm{sup 3+} occurs. The emission spectra of the Ba{sub 2}CaWO{sub 6}:Sm{sup 3+} phosphors consisted of some sharp emission peaks of Sm{sup 3+} ions centre at 579 nm, 618 nm, 625 nm, and 675 nm. The strongest one is located at 610 nm due to {sup 4}G{sub 5/2}→{sup 6}H{sub 7/2} transition of Sm{sup 3+}, generating bright orange–red light. The optimum dopant concentration of Sm{sup 3+} ions in Ba{sub 2}CaWO{sub 6}:xSm{sup 3+} is around 5 mol% and the critical transfer distance of Sm{sup 3+} is calculated as 18 Å. The fluorescence lifetime of Sm{sup 3+} in Ba{sub 2}CaWO{sub 6}:0.05Sm{sup 3+} is 2.36 ms. The Ba{sub 2}CaWO{sub 6}:Sm{sup 3+} phosphors may be potentially used as orange–red phosphors for white light-emitting diodes. - Highlights: • A new host-sensitized Sm{sup 3+}-doped Ba{sub 2}CaWO{sub 6} phosphor was firstly synthesized. • Its structure, luminescent properties are well studied and characterized. • There exists an efficient energy transfer from WO{sub 6}{sup 6−} group to Sm{sup 3+}. • The thermal quenching properties of Ba{sub 2}CaWO{sub 6}:Sm{sup 3+} was firstly evaluated.

  8. Study on photocurrent of bilayers photoanodes using different combination of WO{sub 3} and Fe{sub 2}O{sub 3}

    Energy Technology Data Exchange (ETDEWEB)

    Memar, Amir; Daud, Wan Ramli Wan; Eftekhari, Ehsan; Minggu, Lorna Jeffery [Institute of Fuel Cell, University Kebangsaan Malaysia, 43600 Bangi, Selangor (Malaysia); Hosseini, Soraya [Department Chemical and Environmental Engineering, University Putra Malaysia, 43400 UPM Serdang, Selangor (Malaysia)

    2010-08-15

    Bilayer photoanodes were prepared onto glass substrates (FTO) in order to improve generated photocurrents using UV-vis light by water splitting process. A comparative study of photocatalytic was performed over the films surface using Fe{sub 2}O{sub 3,} WO{sub 3} and mixture of bicomponents (Fe{sub 2}O{sub 3}:WO{sub 3}). Different types of films were prepared using Fe{sub 2}O{sub 3,} WO{sub 3} and bicomponents (mixture) on FTO substrates. The films were grown by sol gel method with the PEG-300 as the structure-directing agent. The photo-generated of the samples were determined by measuring the currents and voltages under illumination of UV-vis light. The morphology, structure and related composition distribution of the films have been characterized by SEM, XRD and EDX respectively. Photocurrent measurements indicated surface roughness as the effective parameter in this study. The deposited surfaces by bicomponents or mixture are flat without any feature on the surface while the deposited surfaces by WO{sub 3} appears rough surface as small round (egg-shaped particles) and cauliflower-like. The surface deposited by Fe{sub 2}O{sub 3} show rough no as well as WO{sub 3} surface. The deposited surfaces by WO{sub 3} reveal the higher value of photocurrent measurement due to surface roughness. Indeed, the roughness can be effective in increasing contact surface area between film and electrolyte and diffuse reflection (light scattering effect). The solution (Fe{sub 2}O{sub 3}:WO{sub 3}) shows the low photocurrent value in compare to WO{sub 3} and Fe{sub 2}O{sub 3} hat it may be due to decomposition the compound at 450 {+-} 1 C to iron-tungstate Fe{sub 2}(WO{sub 4}){sub 3}. (author)

  9. Moessbauer effect study of hyperfine interaction of /sup 161/Dy and /sup 151/Eu in tungsten bronzes Dysub(0. 18) WO/sub 3/ and Eusub(0. 18) WO/sub 3/

    Energy Technology Data Exchange (ETDEWEB)

    Kisynska, K

    1979-01-01

    The Moessbauer technique was used to investigate the hyperfine interaction of /sup 161/Dy and /sup 151/Eu in cubic rare earth tungsten bronzes: Dysub(0.18)WO/sub 3/ and Eusub(0.18)WO/sub 3/. Well resolved hfs spectrum was obtained at 4.2 K for Dysub(0.18)WO/sub 3/. The effective hf field approximation sufficed to interpret the spectrum. The obtained hyperfine interaction parameters were: -g/sub 0/..beta..sub(N)Hsub(eff)=(805+-19) Mc/s and e/sup 2/qQ/sub 0//4 = (506+-56) Mc/s. These results imply that ground doublet of Dy/sup +3/ ion in bronze is a Kramers doublet Vertical Bar+-15/2> with asymmetrical hyperfine tensor Asub(z) non equal to 0, Asub(x) = Asub(y) = 0 and that local crystalline field at RE metal in tungsten bronze at 4.2 K cannot be cubic. From ME absorption spectra of Eusub(0.18)WO/sub 3/ taken at 4.2 K, 78 K and 300 K the values of quadrupole interaction constants for bronze lattice and its temperature dependence were obtained. These data indicate that a phase transition from the high temperature ideal perovskite structure to a distorted one occurs in RE bronzes and that the distortion concerns the nearest tungsten-oxygen environment of RE ion.

  10. Electrochromism and photocatalysis in dendrite structured Ti:WO3 thin films grown by sputtering

    Energy Technology Data Exchange (ETDEWEB)

    Karuppasamy, A., E-mail: karuppasamy@psnacet.edu.in

    2015-12-30

    Graphical abstract: - Highlights: • Dendrite structured Ti doped WO{sub 3} (WTO) thin films are grown by co-sputtering. • Sputtering condition influences structure and surface morphology of WTO films. • Titanium doping and annealing lead to dendritic surface structures in WTO films. • Structural, optical, electrochromic and photocatalytic properties of WTO films. • Enhanced electrochromism and photocatalysis in dendrite structured WTO thin films. - Abstract: Titanium doped tungsten oxide (Ti:WO{sub 3}) thin films with dendrite surface structures were grown by co-sputtering titanium and tungsten in Ar + O{sub 2} atmosphere. Ti:WO{sub 3} thin films were deposited at oxygen flow rates corresponding to pressures in the range 1.0 × 10{sup −3}–5.0 × 10{sup −3} mbar. Argon flow rate and sputtering power densities for titanium (2 W/cm{sup 2}) and tungsten (3 W/cm{sup 2}) were kept constant. Ti:WO{sub 3} films deposited at an oxygen pressure of 5 × 10{sup −3} mbar are found to be better electrochromic and photocatalytic. They have high optical modulation (80% at λ = 550 nm), coloration efficiency (60 cm{sup 2}/C at λ = 550 nm), electron/ion storage and removal capacity (Qc: −22.01 mC/cm{sup 2}, Qa: 17.72 mC/cm{sup 2}), reversibility (80%) and methylene blue decomposition rate (−1.38 μmol/l d). The combined effects of titanium doping, dendrite surface structures and porosity leads to significant enhancement in the electrochromic and photocatalytic properties of Ti:WO{sub 3} films.

  11. Electrochromism and photocatalysis in dendrite structured Ti:WO3 thin films grown by sputtering

    International Nuclear Information System (INIS)

    Karuppasamy, A.

    2015-01-01

    Graphical abstract: - Highlights: • Dendrite structured Ti doped WO 3 (WTO) thin films are grown by co-sputtering. • Sputtering condition influences structure and surface morphology of WTO films. • Titanium doping and annealing lead to dendritic surface structures in WTO films. • Structural, optical, electrochromic and photocatalytic properties of WTO films. • Enhanced electrochromism and photocatalysis in dendrite structured WTO thin films. - Abstract: Titanium doped tungsten oxide (Ti:WO 3 ) thin films with dendrite surface structures were grown by co-sputtering titanium and tungsten in Ar + O 2 atmosphere. Ti:WO 3 thin films were deposited at oxygen flow rates corresponding to pressures in the range 1.0 × 10 −3 –5.0 × 10 −3 mbar. Argon flow rate and sputtering power densities for titanium (2 W/cm 2 ) and tungsten (3 W/cm 2 ) were kept constant. Ti:WO 3 films deposited at an oxygen pressure of 5 × 10 −3 mbar are found to be better electrochromic and photocatalytic. They have high optical modulation (80% at λ = 550 nm), coloration efficiency (60 cm 2 /C at λ = 550 nm), electron/ion storage and removal capacity (Qc: −22.01 mC/cm 2 , Qa: 17.72 mC/cm 2 ), reversibility (80%) and methylene blue decomposition rate (−1.38 μmol/l d). The combined effects of titanium doping, dendrite surface structures and porosity leads to significant enhancement in the electrochromic and photocatalytic properties of Ti:WO 3 films.

  12. Self-Placing Concrete

    OpenAIRE

    ECT Team, Purdue

    2007-01-01

    Certain concrete pours have areas where the congestion of reinforcing bars make placement of concrete almost impossible. Using conventional placing and vibration techniques, the resulting concrete can have considerable honeycombing due to the development of voids. Self-placing concrete is a possible solution to the problem. Also known as self-compactable concrete, self-consolidating concrete, flowable concrete, and non-vibration concrete. These concretes eliminate the need for vibration in a ...

  13. Phase relations and crystal structures in the systems (Bi,Ln)2WO6 and (Bi,Ln)2MoO6 (Ln=lanthanide)

    International Nuclear Information System (INIS)

    Berdonosov, Peter S.; Charkin, Dmitri O.; Knight, Kevin S.; Johnston, Karen E.; Goff, Richard J.; Dolgikh, Valeriy A.; Lightfoot, Philip

    2006-01-01

    Several outstanding aspects of phase behaviour in the systems (Bi,Ln) 2 WO 6 and (Bi,Ln) 2 MoO 6 (Ln=lanthanide) have been clarified. Detailed crystal structures, from Rietveld refinement of powder neutron diffraction data, are provided for Bi 1.8 La 0.2 WO 6 (L-Bi 2 WO 6 type) and BiLaWO 6 , BiNdWO 6 , Bi 0.7 Yb 1.3 WO 6 and Bi 0.7 Yb 1.3 WO 6 (all H-Bi 2 WO 6 type). Phase evolution within the solid solution Bi 2- x La x MoO 6 has been re-examined, and a crossover from γ(H)-Bi 2 MoO 6 type to γ-R 2 MoO 6 type is observed at x∼1.2. A preliminary X-ray Rietveld refinement of the line phase BiNdMoO 6 has confirmed the α-R 2 MoO 6 type structure, with a possible partial ordering of Bi/Nd over the three crystallographically distinct R sites. - Graphical abstract: A summary of phase relations in the lanthanide-doped bismuth tungstate and bismuth molybdate systems is presented, together with some additional structural data on several of these phases

  14. One-dimensional Z-scheme TiO{sub 2}/WO{sub 3}/Pt heterostructures for enhanced hydrogen generation

    Energy Technology Data Exchange (ETDEWEB)

    Gao, Hongqing [School of Materials Science and Engineering, Zhengzhou University, Zhengzhou 450001 (China); State Centre for International Cooperation on Designer Low-carbon and Environmental Materials (SCICDLCEM), Zhengzhou University, Zhengzhou 450001, Henan (China); Zhang, Peng, E-mail: Zhangp@zzu.edu.cn [School of Materials Science and Engineering, Zhengzhou University, Zhengzhou 450001 (China); State Centre for International Cooperation on Designer Low-carbon and Environmental Materials (SCICDLCEM), Zhengzhou University, Zhengzhou 450001, Henan (China); Hu, Junhua, E-mail: Hujh@zzu.edu.cn [School of Materials Science and Engineering, Zhengzhou University, Zhengzhou 450001 (China); State Centre for International Cooperation on Designer Low-carbon and Environmental Materials (SCICDLCEM), Zhengzhou University, Zhengzhou 450001, Henan (China); Pan, Jimin [School of Materials Science and Engineering, Zhengzhou University, Zhengzhou 450001 (China); Fan, Jiajie [School of Materials Science and Engineering, Zhengzhou University, Zhengzhou 450001 (China); State Centre for International Cooperation on Designer Low-carbon and Environmental Materials (SCICDLCEM), Zhengzhou University, Zhengzhou 450001, Henan (China); Shao, Guosheng [School of Materials Science and Engineering, Zhengzhou University, Zhengzhou 450001 (China); State Centre for International Cooperation on Designer Low-carbon and Environmental Materials (SCICDLCEM), Zhengzhou University, Zhengzhou 450001, Henan (China); Institute for Renewable Energy and Environmental Technologies, University of Bolton, Bolton BL35AB (United Kingdom)

    2017-01-01

    Graphical abstract: We reported one-dimensional solid-state Z-scheme photosynthetic heterojunction system with Pt nanoparticle as an electron collector and WO{sub 3} as a hole collector, leading to effective charge separation. - Highlights: • The composite nanofibers were fabricated by facile electrospinning technique. • The composite nanofibers exhibited enhanced activity for H{sub 2} evolution. • Enhanced activity is due to the formation of Z-scheme TiO{sub 2}/WO{sub 3}/Pt heterojunction. - Abstract: One-dimensional Z-scheme TiO{sub 2}/WO{sub 3}/Pt heterostructures were fabricated by integrating a facile electrospinning technique and subsequent annealing in air. X-ray diffraction, scanning electron microscopy, transmission electron microscopy, X-ray photoelectron spectroscopy and UV–vis diffuse reflectance spectroscopy, were used to characterize the as-fabricated samples. The results showed that the H{sub 2}-generation of the as-fabricated one-dimensional Z-scheme TiO{sub 2}/WO{sub 3}/Pt heterostructures (S2) was greatly enhanced compared with pure TiO{sub 2} nanofibers (S0) and TiO{sub 2}/WO{sub 3} nanofibers (S1). The enhanced photocatalyst activities were mainly attributed to the solid-state Z-scheme photosynthetic heterojunction system with Pt nanoparticle as an electron collector and WO{sub 3} as a hole collector, leading to effective charge separation on these semiconductors, which were evidenced by electrochemical impedance spectroscopy (EIS) and photocurrent analysis.

  15. WO3 Nanofiber-Based Biomarker Detectors Enabled by Protein-Encapsulated Catalyst Self-Assembled on Polystyrene Colloid Templates.

    Science.gov (United States)

    Choi, Seon-Jin; Kim, Sang-Joon; Cho, Hee-Jin; Jang, Ji-Soo; Lin, Yi-Min; Tuller, Harry L; Rutledge, Gregory C; Kim, Il-Doo

    2016-02-17

    A novel catalyst functionalization method, based on protein-encapsulated metallic nanoparticles (NPs) and their self-assembly on polystyrene (PS) colloid templates, is used to form catalyst-loaded porous WO3 nanofibers (NFs). The metallic NPs, composed of Au, Pd, or Pt, are encapsulated within a protein cage, i.e., apoferritin, to form unagglomerated monodispersed particles with diameters of less than 5 nm. The catalytic NPs maintain their nanoscale size, even following high-temperature heat-treatment during synthesis, which is attributed to the discrete self-assembly of NPs on PS colloid templates. In addition, the PS templates generate open pores on the electrospun WO3 NFs, facilitating gas molecule transport into the sensing layers and promoting active surface reactions. As a result, the Au and Pd NP-loaded porous WO3 NFs show superior sensitivity toward hydrogen sulfide, as evidenced by responses (R(air)/R(gas)) of 11.1 and 43.5 at 350 °C, respectively. These responses represent 1.8- and 7.1-fold improvements compared to that of dense WO3 NFs (R(air)/R(gas) = 6.1). Moreover, Pt NP-loaded porous WO3 NFs exhibit high acetone sensitivity with response of 28.9. These results demonstrate a novel catalyst loading method, in which small NPs are well-dispersed within the pores of WO3 NFs, that is applicable to high sensitivity breath sensors. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  16. Microstructure and thermochromic properties of VO{sub X}-WO{sub X}-VO{sub X} ceramic thin films

    Energy Technology Data Exchange (ETDEWEB)

    Khamseh, S.; Ghahari, M. [Institute for Color Science and Technology, Department of Nanomaterial and Nanocoatings, Tehran (Iran, Islamic Republic of); Araghi, H. [Islamic Azad University, Department of Materials Engineering, Science and Research Branch, Tehran (Iran, Islamic Republic of); Faghihi Sani, M.A. [Sharif University of Technology, Department of Materials Science and Engineering, Tehran (Iran, Islamic Republic of)

    2016-03-15

    W-doped VO{sub 2} films have been synthesized via oxygen annealing of V-W-V (vanadium-tungsten-vanadium) multilayered films. The effects of middle layer's thickness of V-W-V multilayered film on structure and properties of VO{sub X}-WO{sub X}-VO{sub X} ceramic thin films were investigated. The as-deposited V-W-V multilayered film showed amorphous-like structure when mixed structure of VO{sub 2} (M) and VO{sub 2} (B) was formed in VO{sub X}-WO{sub X}-VO{sub X} ceramic thin films. Tungsten content of VO{sub X}-WO{sub X}-VO{sub X} ceramic thin films increased with increasing middle layer's thickness. With increasing middle layer's thickness, room temperature square resistance (R{sub sq}) of VO{sub X}-WO{sub X}-VO{sub X} ceramic thin films increased from 65 to 86 kΩ/sq. The VO{sub X}-WO{sub X}-VO{sub X} ceramic thin film with the thinnest middle layer showed significant SMT (semiconductor-metal transition) when SMT became negligible on increasing middle layer's thickness. (orig.)

  17. Exploration on anion ordering, optical properties and electronic structure in K{sub 3}WO{sub 3}F{sub 3} elpasolite

    Energy Technology Data Exchange (ETDEWEB)

    Atuchin, V.V. [Laboratory of Optical Materials and Structures, Institute of Semiconductor Physics, SB RAS, Novosibirsk 630090 (Russian Federation); Isaenko, L.I. [Laboratory of Crystal Growth, Institute of Geology and Mineralogy, SB RAS, Novosibirsk 630090 (Russian Federation); Kesler, V.G. [Laboratory of Physical Principles for Integrated Microelectronics, Institute of Semiconductor Physics, Novosibirsk 630090 (Russian Federation); Lin, Z.S., E-mail: zslin@mail.ipc.ac.cn [Technical Institute of Physics and Chemistry, Chinese Academy of Sciences, P.O. Box 2711, Beijing 100190 (China); Molokeev, M.S. [Laboratory of Crystal Physics, Institute of Physics, SB RAS, Krasnoyarsk 660036 (Russian Federation); Yelisseyev, A.P.; Zhurkov, S.A. [Laboratory of Crystal Growth, Institute of Geology and Mineralogy, SB RAS, Novosibirsk 630090 (Russian Federation)

    2012-03-15

    Room-temperature modification of potassium oxyfluorotungstate, G2-K{sub 3}WO{sub 3}F{sub 3}, has been prepared by low-temperature chemical route and single crystal growth. Wide optical transparency range of 0.3-9.4 {mu}m and forbidden band gap E{sub g}=4.32 eV have been obtained for G2-K{sub 3}WO{sub 3}F{sub 3} crystal. Meanwhile, its electronic structure has been calculated with the first-principles calculations. The good agreement between the theorectical and experimental results have been achieved. Furthermore, G2-K{sub 3}WO{sub 3}F{sub 3} is predicted to possess the relatively large nonlinear optical coefficients. - Graphical abstract: Using the cm-size K{sub 3}WO{sub 3}F{sub 3} crystal (left upper), the transmission spectrum (right upper) and XPS valence electronic states (left lower) were measured, agreed with the ab initio results (right lower). Highlights: Black-Right-Pointing-Pointer The cm-size G2-K{sub 3}WO{sub 3}F{sub 3} single crystals are obtained. Black-Right-Pointing-Pointer Optical absorption edge and transmission range are defined for G2-K{sub 3}WO{sub 3}F{sub 3} crystal. Black-Right-Pointing-Pointer Crystal structures of all known K{sub 3}WO{sub 3}F{sub 3} polymorph modifications are determined. Black-Right-Pointing-Pointer Experimental electronic structure is consistent with the first-principles result. Black-Right-Pointing-Pointer G2-K{sub 3}WO{sub 3}F{sub 3} is predicted as a crystal with large NLO coefficients.

  18. A mesoporous WO3−X/graphene composite as a high-performance Li-ion battery anode

    International Nuclear Information System (INIS)

    Liu, Fei; Kim, Jong Gu; Lee, Chul Wee; Im, Ji Sun

    2014-01-01

    Graphical abstract: The highly flexible and conductive graphene layer can enhance electron transfer, protect metal oxides against disintegration and aggregation and buffer the strain induced by volume expansion during cycles. The mesoporous surface layer provides an open network for Li+ diffusion. - Highlights: • Novel cocktail effects of 2D mesoporous WO 3−X /graphene for lithium ion battery. • New approach for lithium ion battery by easy and unique synthesis method. • Mechanism study with proper data for understanding a reaction on anode surface. - Abstract: A novel mesoporous WO 3−X /graphene composite was developed. This material allowed rapid electron and Li + ion diffusion when used as a Li-ion battery (LIB) anode material. Remarkably, the graphene support protected WO 3−X from changing volume during the electrochemical cycling process; this process generally induces capacity loss. The current work describes a high-performance anode material for LIB that has highly dense WO 3−X , as well as high capacity, rate capability and stability

  19. Concrete

    DEFF Research Database (Denmark)

    2015-01-01

    Concrete is a component of coherent transition between a concrete base and a wooden construction. The structure is based on a quantity of investigations of the design possibilities that arise when combining digital fabrication tools and material capacities. Through tangible experiments the project...... specific for this to happen. And the knowledge and intention behind the drawing becomes specialised through the understanding of the fabrication processes and their affect on the materials.The structure Concrete is a result of a multi-angled kerf series in ash wood and a concrete base. The ash wood is cut...... using a 5-axis CNC router with a thin saw blade attached. The programming of the machining results in variations of kerfs that lets the ash wood twist into unique shapes.The shapes of the revolving ash ribbons continue into the concrete creating a cohesive shape. The form for the concrete itself is made...

  20. Advanced nanostructured photocatalysts based on reduced graphene oxide-flower-like Bi{sub 2}WO{sub 6} composites for an augmented simulated solar photoactivity activity

    Energy Technology Data Exchange (ETDEWEB)

    Li, Yukun [Key Laboratory of Integrated Regulation and Resources Development of Shallow Lakes, Ministry of Education, Hohai University, 1st Xikang Road, Nanjing 210098 (China); Chen, Lin [Key Laboratory of Integrated Regulation and Resources Development of Shallow Lakes, Ministry of Education, Hohai University, 1st Xikang Road, Nanjing 210098 (China); College of Environment, Hohai University, 1st Xikang Road, Nanjing 210098 (China); Wang, Yue [Key Laboratory of Integrated Regulation and Resources Development of Shallow Lakes, Ministry of Education, Hohai University, 1st Xikang Road, Nanjing 210098 (China); Zhu, Liang, E-mail: liangzhu_hh@163.com [Key Laboratory of Integrated Regulation and Resources Development of Shallow Lakes, Ministry of Education, Hohai University, 1st Xikang Road, Nanjing 210098 (China); College of Environment, Hohai University, 1st Xikang Road, Nanjing 210098 (China)

    2016-08-15

    Highlights: • A simple route was proposed to prepare flower-like Bi{sub 2}WO{sub 6} and RGO/Bi{sub 2}WO{sub 6}. • Cipro HCl was degraded firstly by RGO/Bi{sub 2}WO{sub 6} under the visible-light. • 2% RGO/Bi{sub 2}WO{sub 6} exhibited the best removal efficiency. - Abstract: A simple hydrothermal process was proposed to prepare the flower-like Bi{sub 2}WO{sub 6} architectures, and the as-synthesized Bi{sub 2}WO{sub 6} photocatalysts were further processed with the prepared graphene oxide (GO) to form novel reduced graphene oxide (RGO)/Bi{sub 2}WO{sub 6} composites. The nano-materials were characterized with the help of XRD, XPS, SEM, FTIR, UV-DRS, PL techniques to investigate their morphological, physical, optical, and photochemical properties. Photocatalytic performances of the pure flower-like Bi{sub 2}WO{sub 6} architectures and RGO/Bi{sub 2}WO{sub 6} composites were compared and evaluated through the degradation of ciprofloxacin hydrochloride (Cipro HCl) wastewater under the simulated visible light. It was found that the RGO/Bi{sub 2}WO{sub 6} composites displayed enhanced visible light-driven photocatalytic activities. It might be that the RGO loading not only effectively suppressed the electron–hole recombination, but also increased the light absorption ability. The effects of operating condition involved in the photocatalytic process were further examined, and the cycle-stability experiment demonstrated that as-obtained 2% RGO/Bi{sub 2}WO{sub 6} photocatalysts had good photocatalytic repeatability.

  1. Build-up Factor Calculation for Ordinary Concrete, Baryte Concrete and Blast-furnace Slugges Concrete as γ Radiation Shielding

    International Nuclear Information System (INIS)

    Isman MT; Elisabeth Supriatni; Tochrul Binowo

    2002-01-01

    Calculation of build up factor ordinary concrete, baryte concrete and blast-furnace sludge concrete have been carried out. The calculations have been carried out by dose rate measurement of Cs 137 source before and after passing through shielding. The investigated variables were concrete type, thickness of concrete and relative possession of concrete. Concrete type variables are ordinary concrete, baryte concrete and blast sludge furnace concrete. The thickness variables were 6, 12, 18, 24, 30 and 36 cm. The relative position variables were dose to the source and close to detector. The result showed that concrete type and position did not have significant effect to build-up factor value, while the concrete thickness (r) and the attenuation coefficient (μ) were influenced to the build-up factor. The higher μr value the higher build-up factor value. (author)

  2. Synthesis and characterization of large WO{sub 3} sheets synthesized by resistive heating method

    Energy Technology Data Exchange (ETDEWEB)

    Filippo, Emanuela, E-mail: emanuela.filippo@unisalento.it [Department of Engineering for Innovation, University of Salento, Monteroni Street, Lecce I-73100 Italy (Italy); Tepore, Marco [Department of Engineering for Innovation, University of Salento, Monteroni Street, Lecce I-73100 Italy (Italy); Baldassarre, Francesca [Department of Cultural Heritage, University of Salento, Lecce I-73100 Italy (Italy); Quarta, Gianluca; Calcagnile, Lucio [Department of Engineering for Innovation, University of Salento, Monteroni Street, Lecce I-73100 Italy (Italy); Guascito, Maria Rachele [DiSTeBA, University of Salento, Lecce I-73100 Italy (Italy); Tepore, Antonio [Department of Cultural Heritage, University of Salento, Lecce I-73100 Italy (Italy)

    2015-09-01

    A simple, low-cost method is presented to grow tungsten oxide large sheets simply by resistively heating a pure tungsten filament under air/water vapor flow. The obtained structures were studied using scanning and transmission electron microscopy, selected area diffraction, X Ray diffraction, Raman and X-ray photoelectron spectroscopy, photoluminescence and zeta potential measurements. SEM observations revealed that sheets formed by broadening of the wires/belts over longer growth period. Photoluminescence measurements showed that tungsten oxide sheets had an intense visible emission band. - Highlights: • WO{sub 3} large sheets were prepared by resistively heating a W filament. • WO{sub 3} sheets were carefully characterized. • Formation mechanism of sheets was studied. • WO{sub 3} sheets had an intense visible emission band at 462 nm.

  3. In situ synthesis of Bi2S3 sensitized WO3 nanoplate arrays with less interfacial defects and enhanced photoelectrochemical performance

    Science.gov (United States)

    Liu, Canjun; Yang, Yahui; Li, Wenzhang; Li, Jie; Li, Yaomin; Chen, Qiyuan

    2016-03-01

    In this study, Bi2S3 sensitive layer has been grown on the surface of WO3 nanoplate arrays via an in situ approach. The characterization of samples were carried out using scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD) and ultraviolet-visible absorption spectroscopy (UV-vis). The results show that the Bi2S3 layer is uniformly formed on the surface of WO3 nanoplates and less interfacial defects were observed in the interface between the Bi2S3 and WO3. More importantly, the Bi2S3/WO3 films as photoanodes for photoelectrochemical (PEC) cells display the enhanced PEC performance compared with the Bi2S3/WO3 films prepared by a sequential ionic layer adsorption reaction (SILAR) method. In order to understand the reason for the enhanced PEC properties, the electron transport properties of the photoelectrodes were studied by using the transient photocurrent spectroscopy and intensity modulated photocurrent spectroscopy (IMPS). The Bi2S3/WO3 films prepared via an in situ approach have a greater transient time constant and higher electron transit rate. This is most likely due to less interfacial defects for the Bi2S3/WO3 films prepared via an in situ approach, resulting in a lower resistance and faster carrier transport in the interface between WO3 and Bi2S3.

  4. Construction method with prestressed connection of precast prestressed concrete using composite slab with multi-round opening web. Bibai factory office building of Dopi Kensetsu Kogyo Co; Web bu ni renzoku enkei kaiko wo yusuru PC gosei yukaita wo mochiita PC kumitate koho. Dopi kensetsu kogyo (kabu) Bibai kojo jimushoto shinchiku koji

    Energy Technology Data Exchange (ETDEWEB)

    Kuramochi, H.; Nakai, J.; Arai, S.; Toriya, T.

    1997-07-31

    This report summarizes the experimental result on the structural performance of precast prestressed concrete (PC) composite slab work, and a construction method with prestressed connection of PC. Although a double T type precast PC slab (DT board) is frequently used as buried form for slabs, it requires extremely complex bar arrangement and complicated works. The reinforcement method of supports using deformed hair pin type bars was thus devised which has a structural performance higher than that of the previous methods as well as simple bar arrangement and superior workability. For the reinforced DT board (DP slab) and the composite slab construction method using the DP slab, the structural safety and retained use environment were confirmed by structural performance test and construction test. The foundation and footing beam of the Bibai factory office building were constructed by the conventional method considering the construction method, while the column, beam and floor by this method using PCa members. The upper building frame was thus completed for as short as 23 days. 5 refs., 15 figs., 4 tabs.

  5. Synthesis and photoluminescence properties of red-emitting Y{sub 6}WO{sub 12}:Eu{sup 3+} phosphors

    Energy Technology Data Exchange (ETDEWEB)

    Chien, Tzu-Chin; Yang, Ji-Chun; Hwang, Chii-Shyang, E-mail: cshwang@mail.ncku.edu.tw; Yoshimura, Masahiro

    2016-08-15

    For a system of white-light-emitting diodes (WLEDs) fabricated using near-ultraviolet (UV) LED chips coated with RGB tri-color phosphors, the most important issue is enhancing the efficiency of the red phosphor. Y{sub 6}WO{sub 12}:Eu{sup 3+} phosphor is a potential material that can emit red color under near-UV excitation. This work investigated the luminescence properties of Y{sub 6}WO{sub 12}:Eu{sup 3+} under UV light excitation. The photoluminescence (PL) emission intensity of Eu{sub x}Y{sub 6–x}WO{sub 12} (x = 0.1–1.0) phosphor from the {sup 5}D{sub 0}→{sup 7}F{sub 2} transition increased with Eu{sup 3+} content until x = 0.9. For x > 0.9, the PL emission intensity decreased due to concentration quenching. The decay time of Eu{sub x}Y{sub 6–x}WO{sub 12} (x = 0.1–1.0) phosphor for the {sup 5}D{sub 0}→{sup 7}F{sub 2} transition was about 0.6–0.7 ms and did not decrease obviously, which means that there was no nonradiative energy transfer in the phosphor. The asymmetry ratio ({sup 5}D{sub 0} → {sup 7}F{sub 2}/{sup 5}D{sub 0} → {sup 7}F{sub 1}) of Eu{sub x}Y{sub 6–x}WO{sub 12} (x = 0.1–1.0) was about 2, which caused the PL emission intensity of Eu{sub x}Y{sub 6–x}WO{sub 12} (x = 0.1–1.0) phosphor from the {sup 5}D{sub 0}→{sup 7}F{sub 2} transition to be higher than that from the {sup 5}D{sub 0}→{sup 7}F{sub 1} transition. The chromaticity coordinates of the Eu{sub x}Y{sub 6–x}WO{sub 12} (x = 0.1–1.0) phosphor were close to the chromaticity coordinates of the standard red color. The Eu{sub x}Y{sub 6–x}WO{sub 12} (x = 0.9) phosphor showed the highest quantum efficiency. - Highlights: • Eu{sub x}Y{sub 6–x}WO{sub 12} (x = 0.1–1.0) phosphors were synthesized via a solid-state reaction. • Strongest excitation peaks observed at 392 nm (near UV) and 463 nm (blue). • The major emission peak of the red phosphor excited by 392 nm was at 605 nm. • The quantum efficiency of Eu{sub x}Y{sub 6–x}WO{sub 12} (x = 0.1–1.0) phosphors

  6. Synthesis and luminescent properties of two different Y{sub 2}WO{sub 6}:Eu{sup 3+} phosphor phases

    Energy Technology Data Exchange (ETDEWEB)

    Llanos, Jaime, E-mail: jllanos@ucn.cl [Departamento de Química, Universidad Católica del Norte, Avda. Angamos 0610, Antofagasta (Chile); Olivares, Douglas [Departamento de Química, Universidad Católica del Norte, Avda. Angamos 0610, Antofagasta (Chile); Manríquez, Víctor; Espinoza, Darío [Departamento de Química, Universidad de Chile, Las Palmeras 3425, Santiago (Chile); Brito, Ivan [Departamento de Química, Universidad de Antofagasta, Campus Coloso, Antofagasta (Chile)

    2015-04-15

    Highlights: • Synthesis of two phases Y{sub 2−x}Eu{sub x}WO{sub 6}. One of them crystallizes as Aurivillius phase. • Optical properties of the phosphors Y{sub 2}WO{sub 6}:Eu{sup 3+} (monoclinic and orthorhombic phases). • The orthorhombic phase was prepared via low-temperature combustion synthesis method. - Abstract: In this paper, two different Y{sub 2−x}Eu{sub x}WO{sub 6} phases were synthesized. The monoclinic phase was prepared via a conventional solid-state reaction, whereas the orthorhombic phase was obtained via a facile, low-temperature combustion synthesis method. X-ray diffraction (XRD), scanning electron microscopy (SEM), differential scanning calorimetry (DSC), and photoluminescence (PL) spectroscopy were used to characterize the resulting phosphors. The XRD results indicate the orthorhombic phase crystallized isostructurally with the Aurivillius Bi{sub 2}WO{sub 6} phase, whereas the other polymorph crystallized isostructurally with Yb{sub 2}WO{sub 6} in the monoclinic system. The SEM studies revealed both phases had a strong tendency to form agglomerates averaging nanometers in size. The photoluminescence emission spectra confirmed all of the samples were efficiently excited by near UV light and were dominated by the electric dipole transition {sup 5}D{sub 0} → {sup 7}F{sub 2}. The orthorhombic Y{sub 2−x}Eu{sub x}WO{sub 6} excitation spectrum possessed a broad band across the entire UV region (220–400 nm); therefore, Y{sub 1.86}Eu{sub 0.14}WO{sub 6} could be considered an efficient spectral converter material for use in dye-sensitized solar cells.

  7. NANOMODIFIED CONCRETE

    Directory of Open Access Journals (Sweden)

    B. M. Khroustalev

    2015-01-01

    Full Text Available One of the main directions in construction material science is the development of  next generation concrete that is ultra-dense, high-strength, ultra-porous, high heat efficient, extra corrosion-resistant. Selection of such direction is caused by extreme operational impacts on the concrete, namely: continuously increasing load on the concrete and various dynamics of such loads; the necessity in operation of concrete products in a wide temperature range and their exposure to various chemical and physical effects.The next generation concrete represents high-tech concrete mixtures with additives that takes on and retain the required properties when hardening and being used under any operational conditions. A differential characteristic of the next generation concrete is its complexity that presumes usage of various mineral dispersed components, two- and three fractional fine and coarse aggregates, complex chemical additives, combinations of polymer and iron reinforcement.Design strength and performance properties level of the next generation concrete is achieved by high-quality selection of the composition, proper selection of manufacturing techniques, concrete curing, bringing the quality of concrete items to the required level of technical condition during the operational phase. However, directed formation of its structure is necessary in order to obtain high-tech concrete.Along with the traditional methods for regulation of the next generation concrete structure, modification of concrete while using silica nanoparticles is also considered as a perspective one because the concrete patterning occurs due to introduction of a binder in a mineral matrix. Due to this it is possible to obtain nano-modified materials with completely new properties.The main problem with the creation of nano-modified concrete is a uniform distribution of nano-materials in the volume of the cement matrix which is particularly important in the cases of adding a modifier in

  8. [Doctor's degree thesis of Tomasz Adolf Wołkowiński "Carditidis rheumaticae historia"].

    Science.gov (United States)

    Stembrowicz, W

    2001-01-01

    In 1817 on the University of Vilnius Faculty of Medicine, T. A. Wołkowiński, a student of the eminent clinician Józef Frank, defended his doctor's degree thesis about a direct relation between rheumatic disease and cardiomegaly. It was probably the first paper in Poland describing with details the rheumatic heart disease. Unfortunately we don't know much about T. A. Wołkowiński's life.

  9. Study on reinforced concrete high-rise building using prefabricated beam-column joints. Part 3. ; Basic anchorage behaviors of longitudinal bars of beams. Hahsirater dot hari setsugobu PC ka koho (PG connection koho) wo mochiita RC koso tatemono no kaihatsu. 3. ; Hari shukin no kisoteki teichaku seijo

    Energy Technology Data Exchange (ETDEWEB)

    SEkine, M.; Yoshioka, K.; Eto, H. (Obayashi Corp., Tokyo (Japan))

    1991-08-10

    Pull-out tests were carried out to examine basic anchorage behaviors of through holes for beam re-bars by using a PG connection method, in which columns and beam-column joints with through holes for beam re-bars in the reinforced concrete framed construction are precast simultaneously. Specimens made by the PG connection method showed better anchorage behaviors than specimens made by the conventional anchorage method. In case of anchorage width of 80cm and concrete strength of about 350kgf/cm{sup 2}, it was recognized that large slipping of re-bars did not occur under allowable bond stress when the interval between re-bars was not less than 15cm and covering depth to the core of re-bars was not less than 8cm. Concerning a specimen which did not show splitting bond failure because of lateral compressive stress, bond stress of re-bars when large slipping occurred was 1.5 times or more in comparison with the allowable bond stress. Since this specimen held high slipping rigidity even after increase of slipping, its anchoring stress increased by 32-57% compared with a specimen without lateral compressive stress. 4 refs., 7 figs., 3 tabs.

  10. The enhanced photoactivity of nanosized Bi2WO6 catalyst for the degradation of 4-chlorophenol

    International Nuclear Information System (INIS)

    Fu Hongbo; Yao Wenqing; Zhang Liwu; Zhu Yongfa

    2008-01-01

    Nanosized Bi 2 WO 6 catalyst exhibited the enhanced photoactivity for the degradation of 4-chlorophenol (4-CP) under visible irradiation compared to the sample prepared by high-temperature solid reaction. The photoactivity of the catalyst was sensitive to pH variation of the suspension. Nanosized Bi 2 WO 6 catalyst showed the highest activity at pH 7.2. The photodegradation of 4-CP by nanosized Bi 2 WO 6 catalyst followed a pseudo-first-order reaction. After three recycling runs for the photodegradation of 4-CP, the activity of the catalyst did not show any significant loss, suggesting that the catalyst was stable under visible irradiation

  11. Highly efficient perovskite solar cells based on a nanostructured WO3-TiO2 core-shell electron transporting material

    KAUST Repository

    Mahmood, Khalid; Swain, Bhabani Sankar; Kirmani, Ahmad R.; Amassian, Aram

    2015-01-01

    Until recently, only mesoporous TiO2 and ZnO were successfully demonstrated as electron transport layers (ETL) alongside the reports of ZrO2 and Al2O3 as scaffold materials in organometal halide perovskite solar cells, largely owing to ease of processing and to high power conversion efficiency. In this article, we explore tungsten trioxide (WO3)-based nanostructured and porous ETL materials directly grown hydrothermally with different morphologies such as nanoparticles, nanorods and nanosheet arrays. The nanostructure morphology strongly influences the photocurrent and efficiency in organometal halide perovskite solar cells. We find that the perovskite solar cells based on WO3 nanosheet arrays yield significantly enhanced photovoltaic performance as compared to nanoparticles and nanorod arrays due to good perovskite absorber infiltration in the porous scaffold and more rapid carrier transport. We further demonstrate that treating the WO3 nanostructures with an aqueous solution of TiCl4 reduces charge recombination at the perovskite/WO3 interface, resulting in the highest power conversion efficiency of 11.24% for devices based on WO3 nanosheet arrays. The successful demonstration of alternative ETL materials and nanostructures based on WO3 will open up new opportunities in the development of highly efficient perovskite solar cells. This journal is © The Royal Society of Chemistry 2015.

  12. Synthesis of γ-WO{sub 3} thin films by hot wire-CVD and investigation of its humidity sensing properties

    Energy Technology Data Exchange (ETDEWEB)

    Jadkar, Vijaya; Waykar, Ravindra; Jadhavar, Ashok [School of Energy Studies, Savitribai Phule Pune University, Pune 411 007 (India); Pawbake, Amit [School of Energy Studies, Savitribai Phule Pune University, Pune 411 007 (India); Physical and Material Chemistry Division, National Chemical Laboratory, Pune 411 008 (India); Date, Abhijit [School of Aerospace, Mechanical and Manufacturing Engineering, RMIT University, Plenty Road, Bundoora, Melbourne VIC 3083 (Australia); Late, Dattatray [Physical and Material Chemistry Division, National Chemical Laboratory, Pune 411 008 (India); Pathan, Habib; Gosavi, Suresh; Jadkar, Sandesh [Department of Physics, Savitribai Phule Pune University, Pune 411 007 (India)

    2017-05-15

    In this study, monoclinic tungsten oxide (γ-WO{sub 3}) have been grown in a single step using HW-CVD method by resistively heating W filaments in a constant O{sub 2} pressure. The formation of γ-WO{sub 3} was confirmed using low angle-XRD and Raman spectroscopy analysis. Low angle-XRD analysis revealed that as-deposited WO{sub 3} film are highly crystalline and the crystallites have preferred orientation along the (002) direction. HRTEM analysis and SAED pattern also show the highly crystalline nature of WO{sub 3} with d spacing of ∝ 0.38 nm, having an orientation along the (002) direction. Surface topography investigated by SEM analysis shows the formation of a uniform and homogeneous cauliflower like morphology throughout the substrate surface without flaws and cracks. A humidity sensing device incorporating WO{sub 3} is also fabricated, which shows a maximum humidity sensitivity factor of ∝ 3954% along with a response time of ∝14 s and a recovery time of ∝25 s. The obtained results demonstrate that it is possible to synthesize WO{sub 3} in a single step by HW-CVD method and to fabricate a humidity sensor by using it. (copyright 2017 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  13. Effect of direct current density on microstructure of tungsten coating electroplated from Na{sub 2}WO{sub 4}-WO{sub 3}-NaPO{sub 3} system

    Energy Technology Data Exchange (ETDEWEB)

    Jiang, Fan, E-mail: jiangfan1109@163.com; Zhang, Yingchun, E-mail: zycustb@163.com; Sun, Ningbo, E-mail: suningbo682@163.com; Liu, Zhi’ang, E-mail: zhiang_001@163.com

    2014-10-30

    Highlights: • Tungsten coatings were electroplated from the Na{sub 2}WO{sub 4}-WO{sub 3}-NaPO{sub 3} melt. • Tungsten coating comprised a tooth-like layer and a columnar growth layer. • The average grain size increases as increasing current density. • (2 1 1) Orientation is favored most likely for samples obtained at various durations. • The growth rate of tungsten crystal nucleus is higher than the nucleation rate. - Abstract: Pure tungsten coating with body-centered cubic (bbc) structure was successfully electrodeposited from Na{sub 2}WO{sub 4}-WO{sub 3}-NaPO{sub 3} molten salt at 1153 K in atmosphere. The coatings comprised an inner layer of tooth-like grains and an outer layer of columnar grains with a thin diffusion layer of tungsten in the Cu substrate. The effects of current density and electrodeposition duration on the morphology and microstructure of the coatings were investigated in this paper. With increasing of current density from 50 to 80 mA cm{sup −2}, the grain size of the tungsten coating increased from 7.01 μm to 12.44 μm. With the increase of the current density, the thickness of the coating changed from 25.92 μm to 34.40 μm, and then dropped to 29.72 μm. The preferred orientation of the coatings changed from (2 2 0) to (2 1 1). With the increasing of duration, the grain size and thickness of tungsten coatings increased while the (2 1 1) favored orientation dot not changed. Because of the low current efficiency at long duration of direct current electrodeposition, it should not be suitable for the electroplating of thick tungsten coating.

  14. First-order character of the displacive structural transition in BaWO4

    International Nuclear Information System (INIS)

    Tan Da-Yong; Xiao Wan-Sheng; Zhou Wei; Chen Ming; Xiong Xiao-Lin; Song Mao-Shuang

    2012-01-01

    Nearly all displacive transitions have been considered to be continuous or second order, and the rigid unit mode (RUM) provides a natural candidate for the soft mode. However, in-situ X-ray diffraction and Raman measurements show clearly the first-order evidences for the scheelite-to-fergusonite displacive transition in BaWO 4 : a 1.6% volume collapse, coexistence of phases, and hysteresis on release of pressure. Such first-order signatures are found to be the same as the soft modes in BaWO 4 , which indicates the scheelite-to-fergusonite displacive phase transition hides a deeper physical mechanism. By the refinement of atomic displacement parameters, we further show that the first-order character of this phase transition stems from a coupling of large compression of soft BaO 8 polyhedrons to the small displacive distortion of rigid WO 4 tetrahedrons. Such a coupling will lead to a deeper physical insight in the phase transition of the common scheelite-structured compounds. (condensed matter: structural, mechanical, and thermal properties)

  15. Facile synthesis of NiWO4/reduced graphene oxide nanocomposite with excellent capacitive performance for supercapacitors

    International Nuclear Information System (INIS)

    Xu, Xiaowei; Pei, Liyuan; Yang, Yang; Shen, Jianfeng; Ye, Mingxin

    2016-01-01

    NiWO 4 /reduced graphene oxide (NWG) nanocomposite was successfully synthesized through a facile one-pot solvothermal method for the first time. The resulting nanocomposite is composed of NiWO 4 nanoparticles that are uniformly attached on graphene sheets by in situ reducing. The as-prepared NWG composite has been systematically characterized by Powder X-ray diffraction, Fourier transform infrared spectra, Raman spectroscopy, Thermogravimetric analysis, Scanning electron microscopy, Transmission electron microscopy, X-ray photoelectron spectra, and Brunauer–Emmett–Teller analysis. The capacitive performances of the as-prepared NWG composite as electrode material are investigated. It is found that the NWG composite exhibits a high specific capacitance up to 1031.3 F g −1 at a current density of 0.5 A g −1 . The greatly enhanced capacitive performance of the NWG electrode can be attributed to the synergetic effect of NiWO 4 nanoparticles and RGO, which provides conducting channels and active sites. The cyclic stability tests demonstrated no decreases of its initial values after 5000 cycles, suggesting that such hybrid electrode possesses a great potential application in energy-storage devices. - Highlights: • NiWO 4 /RGO composite was successfully prepared through a facile solvothermal method. • The NiWO 4 /RGO composite shows a high specific capacitance of 1031.3 F g −1 . • Enhanced electrical conductivity leads to superior electrochemical performance.

  16. Identifying Sources of Scientific Knowledge: classifying non-source items in the WoS

    Energy Technology Data Exchange (ETDEWEB)

    Calero-Medina, C.M.

    2016-07-01

    The sources of scientific knowledge can be tracked using the references in scientific publications. For instance, the publications from the scientific journals covered by the Web of Science database (WoS) contain references to publications for which an indexed source record exist in the WoS (source items) or to references for which an indexed source record does not exist in the WoS (non-source items). The classification of the non-source items is the main objective of the work in progress presented here. Some other scholars have classified and identified non-source items with different purposes (e.g. Butler & Visser (2006); Liseé, Larivière & Archambault (2008); Nerderhof, van Leeuwen & van Raan (2010); Hicks & Wang (2013); Boyack & Klavans (2014)). But these studies are focused in specific source types, fields or set of papers. The work presented here is much broader in terms of the number of publications, source types and fields. (Author)

  17. Silver loaded WO3−x/TiO2 composite multifunctional thin films

    International Nuclear Information System (INIS)

    Dunnill, Charles W.; Noimark, Sacha; Parkin, Ivan P.

    2012-01-01

    Multifunctional WO 3−x –TiO 2 composite thin films have been prepared by sol–gel synthesis and shown to be good visible light photocatalysts whilst retaining a desirable underlying blue colouration. The WO 3−x –TiO 2 composite thin films were further enhanced using silver nanoparticles synthesised in-situ on the surface from the photo-degradation of silver nitrate solution. Thin films were characterised using X-ray diffraction, Raman, Scanning electron microscopy and UV–visible spectroscopy and shown to photo degrade stearic acid, using white light λ = 420–800 nm. - Highlights: ► WO 3−X TiO 2 composite thin films were synthesised by sol–gel methods. ► Blue tinted glass is desirable for the value added glass industry. ► Silver nanoparticle island formation enhances the activity of the films. ► Blue tinted “value added” coated glass is now possible.

  18. Features and performance of PCa board which cuts off the electromagnetic wave. Electromagnetic shield building using the carbon fiber contamination PCa board; Denjiha wo shadansuru PCa ban no tokucho to seino. Tanso sen'i konnyu PCa ban wo mochiita denji shirudobiru

    Energy Technology Data Exchange (ETDEWEB)

    Yoshida, Katsuo; Kasai, Yasuaki [Obayashi Corp., Osaka (Japan); Okada, Shin' ichiro; Sakamoto, Shin [Osaka Gas Corp., Osaka (Japan)

    1999-03-10

    With the rapid popularization of public radio information communication equipment, portable telephones, wireless LAN, etc., the interception (building shield) of the electromagnetic wave internal and external the building becomes large problem. As process equal to the convention and the method in which the cost is possible, they did do not shield the whole building, and also ensure the comfort as an office, and PCa board which mixed the carbon fiber into the mortar was developed. They described the survey result of the electromagnetic shield performance of the building which constructed by using this in external wall. They explained electromagnetism characteristics of the contamination mortar and application to the PCa board and method. They carried out the measurement in the electromagnetic shield room laboratory, and they obtained next result. 1) There is seldom on the effect both only the concrete and only by the carbon fiber mesh. 2) They considered the effect that carbon fiber chop 1% are mixed into the concrete. 3) The effect became a maximum, when carbon fiber chop and carbon fiber mesh were mixed, and they confirmed being excellent cost-concerned. (NEDO)

  19. Bibliometric analysis of publications on wine tourism in the databases Scopus and WoS

    Directory of Open Access Journals (Sweden)

    Amador Durán Sánchez

    2017-01-01

    Full Text Available The aim of this study was to show the current state of scientific research regarding wine tourism, by comparing the platforms of scientific information WoS and Scopus and applying quantitative methods. For this purpose, a bibliometric study of the publications indexed in WoS and Scopus was conducted, analyzing the correlation between increases, coverage, overlap, dispersion and concentration of documents. During the search process, a set of 238 articles and 122 different journals were obtained. Based on the results of the comparative study, we conclude that WoS and Scopus databases differ in scope, data volume and coverage policies with a high degree of unique sources and articles, resulting both of them complementary and not mutually exclusive. Scopus covers the area of wine tourism better, by including a greater number of journals, papers and signatures.

  20. Temperature dependent selective detection of hydrogen and acetone using Pd doped WO3/reduced graphene oxide nanocomposite

    Science.gov (United States)

    Kaur, Jasmeet; Anand, Kanica; Kohli, Nipin; Kaur, Amanpreet; Singh, Ravi Chand

    2018-06-01

    Reduced graphene oxide (RGO) and Pd doped WO3 nanocomposites were fabricated by employing electrostatic interactions between poly (diallyldimethylammonium chloride) (PDDA) modified Pd doped WO3 nanostructures and graphite oxide (GO) and studied for their gas sensing application. XRD, Raman, FTIR, FESEM-EDX, TEM, TGA, XPS and Photoluminescence techniques were used for characterization of as-synthesized samples. Gas sensing studies revealed that the sensor with optimized doping of 1.5 mol% Pd and 1 wt% GO shows temperature dependent selectivity towards hydrogen and acetone. The role of WO3, Pd and RGO has been discussed in detail for enhanced sensing performance.

  1. Three-dimensional Ag{sub 2}O/WO{sub 3}·0.33H{sub 2}O heterostructures for improving photocatalytic activity

    Energy Technology Data Exchange (ETDEWEB)

    He, Xiaoyu [Department of Applied Physics, Chongqing University, Chongqing 400044 (China); Department of Physics and Electronic Engineering, Yangtze Normal University, Chongqing 408100 (China); Hu, Chenguo, E-mail: hucg@cqu.edu.cn [Department of Applied Physics, Chongqing University, Chongqing 400044 (China); Xi, Yi; Zhang, Kaiyou; Hua, Hao [Department of Applied Physics, Chongqing University, Chongqing 400044 (China)

    2014-02-01

    Highlights: • Ag{sub 2}O/WO{sub 3}·0.33H{sub 2}O 3D network heterostructures are prepared via a simple precipitatation method. • Ag{sub 2}O/WO{sub 3}·0.33H{sub 2}O networks exhibit much enhanced photocatalytic activity. • High photocatalytic activity is attributed to its heterostructure and 3D architectures. - Abstract: Three-dimensional Ag{sub 2}O/WO{sub 3}·0.33H{sub 2}O heterostructures were fabricated by loading Ag{sub 2}O nanoparticles on WO{sub 3}·0.33H{sub 2}O 3D networks via a simple chemical precipitation method. The Ag{sub 2}O/WO{sub 3}·0.33H{sub 2}O heterostructures exhibited much enhanced photocatalytic activity for the degradation of methylene blue (MB) under simulated solar light irradiation. The optimal molar ratio of Ag{sub 2}O and WO{sub 3}·0.33H{sub 2}O is 1:2. The outstanding photocatalytic activity of the Ag{sub 2}O/WO{sub 3}·0.33H{sub 2}O can be attributed to its large surface area of the three-dimensional networks, the enhanced sunlight absorption and the prevention of electrons–holes combination from the heterostructures. The experiment result demonstrates that wide band gap semiconductor (WO{sub 3}·0.33H{sub 2}O) modified by narrow band gap metal oxide (Ag{sub 2}O) with 3D architecture will be an effective route to enhance its photocatalytic activity.

  2. A novel orange emissive phosphor SrWO4:Sm3+ for white light-emitting diodes

    International Nuclear Information System (INIS)

    Ju Zhenghua; Wei Ruiping; Ma Jingxin; Pang Chaoran; Liu Weisheng

    2010-01-01

    Research highlights: → A novel orange emissive phosphor SrWO 4 :Sm 3+ was firstly reported. → The optics properties of Sm 3+ -doped SrWO 4 phosphor were successfully discussed. → The temperature-dependent luminescence indicates the phosphor exhibits a small thermal-quenching property. → The phosphor is a potential candidate as orange-emitting component for white LED. - Abstract: A novel orange emissive phosphor, Sm 3+ -doped SrWO 4 , was synthesized by high temperature solid-state reaction in air atmosphere. The excitation spectra show that the phosphors can be efficiently excited by ultraviolet and near-ultraviolet light, the optimized concentration is 4 mol%. Three emission peaks locate at 562, 596 and 642 nm, corresponding to CIE chromaticity coordinates of (x = 0.54, y = 0.46), which indicates the orange light emitting. The decay curves are well fitted with triple-exponential decay models. The quantum yield of the Sr 0.96 Sm 0.04 WO 4 phosphor is about 70.65% under excitation of 377 nm. Furthermore, the temperature-dependent luminescence indicates the phosphor exhibits a small thermal-quenching property. So the phosphor is able to be applied to UV-LED chip-based white light-emitting diodes.

  3. High Performance Concrete

    Directory of Open Access Journals (Sweden)

    Traian Oneţ

    2009-01-01

    Full Text Available The paper presents the last studies and researches accomplished in Cluj-Napoca related to high performance concrete, high strength concrete and self compacting concrete. The purpose of this paper is to raid upon the advantages and inconveniences when a particular concrete type is used. Two concrete recipes are presented, namely for the concrete used in rigid pavement for roads and another one for self-compacting concrete.

  4. Electron microscopy analyses and electrical properties of the layered Bi{sub 2}WO{sub 6} phase

    Energy Technology Data Exchange (ETDEWEB)

    Taoufyq, A. [Institut Matériaux Microélectronique et Nanosciences de Provence, IM2NP, UMR CNRS 7334, Université du Sud Toulon-Var, BP 20132, 83957, La Garde Cedex (France); Laboratoire Matériaux et Environnement LME, Faculté des Sciences, Université Ibn Zohr, BP 8106, Cité Dakhla, Agadir, Maroc (Morocco); Département d‘Études des Réacteurs, Laboratoire Dosimétrie Capteurs Instrumentation, CEA Cadarache (France); Société CESIGMA—Signals and Systems, 1576 Chemin de La Planquette, F 83 130 LA GARDE (France); Ait Ahsaine, H. [Laboratoire Matériaux et Environnement LME, Faculté des Sciences, Université Ibn Zohr, BP 8106, Cité Dakhla, Agadir, Maroc (Morocco); Patout, L. [Institut Matériaux Microélectronique et Nanosciences de Provence, IM2NP, UMR CNRS 7334, Université du Sud Toulon-Var, BP 20132, 83957, La Garde Cedex (France); Benlhachemi, A.; Ezahri, M. [Laboratoire Matériaux et Environnement LME, Faculté des Sciences, Université Ibn Zohr, BP 8106, Cité Dakhla, Agadir, Maroc (Morocco); and others

    2013-07-15

    The bismuth tungstate Bi{sub 2}WO{sub 6} was synthesized using a classical coprecipitation method followed by a calcination process at different temperatures. The samples were characterized by X-ray diffraction, simultaneous thermogravimetry and differential thermal analysis (TGA/DTA), scanning and transmission electron microscopy (SEM, TEM) analyses. The Rietveld analysis and electron diffraction clearly confirmed the Pca2{sub 1} non centrosymmetric space group previously proposed for this phase. The layers Bi{sub 2}O{sub 2}{sup 2+} and WO{sub 4}{sup 2−} have been directly evidenced from the HRTEM images. The electrical properties of Bi{sub 2}WO{sub 6} compacted pellets systems were determined from electrical impedance spectrometry (EIS) and direct current (DC) analyses, under air and argon, between 350 and 700 °C. The direct current analyses showed that the conduction observed from EIS analyses was mainly ionic in this temperature range, with a small electronic contribution. Electrical change above the transition temperature of 660 °C is observed under air and argon atmospheres. The strong conductivity increase observed under argon is interpreted in terms of formation of additional oxygen vacancies coupled with electron conduction. - Graphical abstract: High resolution transmission electron microscopy: inverse fast Fourier transform giving the layered structure of the Bi{sub 2}WO{sub 6} phase, with a representation of the cell dimensions (b and c vectors). The Bi{sub 2}O{sub 2}{sup 2+} and WO{sub 4}{sup 2−} sandwiches are visible in the IFFT image. - Highlights: • Using transmission electron microscopy, we visualize the layered structure of Bi{sub 2}WO{sub 6}. • Electrical analyses under argon gas show some increase in conductivity. • The phase transition at 660 °C is evidenced from electrical modification.

  5. How Concrete is Concrete?

    Directory of Open Access Journals (Sweden)

    Koeno Gravemeijer

    2011-01-01

    Full Text Available If we want to make something concrete in mathematics education, we are inclined introduce, what we call, ‘manipulatives’, in the form of tactile objects or visual representations. If we want to make something concrete in a everyday-life conversation, we look for an example. In the former, we try to make a concrete model of our own, abstract, knowledge; in the latter, we try to find an example that the others will be familiar with. This article first looks at the tension between these two different ways of making things concrete. Next another role of manipulatives, will be discussed, namely that of means for scaffolding and communication. In this role, manipulatives may function as means of support in a process that aims at helping students to build on their own thinking while constructing more sophisticated mathematics.Key words:  Conceret Learning Materials, School Math, Common Sense, Scaffolding, Communication DOI: http://dx.doi.org/10.22342/jme.2.1.780.1-14

  6. Properties of high-workability concrete with recycled concrete aggregate

    OpenAIRE

    Safiuddin,; Alengaram,Ubagaram Johnson; Salam,Abdus; Jumaat,Mohd Zamin; Jaafar,Fahrol Fadhli; Saad,Hawa Binti

    2011-01-01

    This study presents the effects of recycled concrete aggregate (RCA) on the key fresh and hardened properties of concrete. RCA was used to produce high-workability concrete substituting 0-100% natural coarse aggregate (NCA) by weight. The slump and slump flow of fresh concretes were determined to ensure high workability. In addition, the compressive, flexural and splitting tensile strengths, modulus of elasticity, and permeable voids of hardened concretes were determined. The test results rev...

  7. Template-free synthesis of ZnWO{sub 4} powders via hydrothermal process in a wide pH range

    Energy Technology Data Exchange (ETDEWEB)

    Hojamberdiev, Mirabbos, E-mail: mirabbos_uz@yahoo.com [Shaanxi Key Laboratory of Nano-materials and Technology, Xi' an University of Architecture and Technology, Xi' an 710055 (China); Zhu, Gangqiang [School of Physics and Information Technology, Shaanxi Normal University, Xi' an 710062 (China); Xu, Yunhua [Shaanxi Key Laboratory of Nano-materials and Technology, Xi' an University of Architecture and Technology, Xi' an 710055 (China)

    2010-12-15

    ZnWO{sub 4} powders with different morphologies were fabricated through a template-free hydrothermal method at 180 {sup o}C for 8 h in a wide pH range. X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), UV-visible and luminescence spectrophotometers were applied to study the effects of pH values on crystallinity, morphology, optical and luminescence properties. The XRD results showed that the WO{sub 3} + ZnWO{sub 4}, ZnWO{sub 4}, and ZnO phases could form after hydrothermal processing at 180 {sup o}C for 8 h with the pH values of 1, 3-11, and 13, respectively. The SEM and TEM observation revealed that the morphological transformation of ZnWO{sub 4} powders occurred with an increase in pH values as follows: star anise-, peony-, and desert rose-like microstructures and soya bean- and rod-like nanostructures. The highest luminescence intensity was found to be in sample consisting of star anise-like crystallites among all the samples due to the presence of larger particles with high crystallinity resulted from the favorable pH under the current hydrothermal conditions.

  8. Fabrication and photocatalytic activity enhanced mechanism of direct Z-scheme g-C{sub 3}N{sub 4}/Ag{sub 2}WO{sub 4} photocatalyst

    Energy Technology Data Exchange (ETDEWEB)

    Zhu, Bicheng [State Key Laboratory of Advanced Technology for Materials Synthesis and Processing, Wuhan University of Technology, Wuhan 430070 (China); Department of Science and Environmental Studies The Hong Kong Institute of Education, Tai Po, N.T., Hong Kong (China); Xia, Pengfei; Li, Yao [State Key Laboratory of Advanced Technology for Materials Synthesis and Processing, Wuhan University of Technology, Wuhan 430070 (China); Ho, Wingkei, E-mail: keithho@ied.edu.hk [Department of Science and Environmental Studies The Hong Kong Institute of Education, Tai Po, N.T., Hong Kong (China); Yu, Jiaguo, E-mail: jiaguoyu@yahoo.com [State Key Laboratory of Advanced Technology for Materials Synthesis and Processing, Wuhan University of Technology, Wuhan 430070 (China); Department of Physics, Faculty of Science, King Abdulaziz University, Jeddah 21589 (Saudi Arabia)

    2017-01-01

    Highlights: • g-C{sub 3}N{sub 4} acted as a support for the in situ growth of β-Ag{sub 2}WO{sub 4}. • g-C{sub 3}N{sub 4} nanosheets inhibited the phase transformation of β-Ag{sub 2}WO{sub 4} to α-Ag{sub 2}WO{sub 4}. • g-C{sub 3}N{sub 4}/Ag{sub 2}WO{sub 4} exhibited a superior photocatalytic activity. • A direct Z-scheme photocatalytic mechanism could explain activity enhancement. - Abstract: Herein, a direct Z-scheme graphitic carbon nitride (g-C{sub 3}N{sub 4})/silver tungstate (Ag{sub 2}WO{sub 4}) photocatalyst was prepared by a facile in situ precipitation method using g-C{sub 3}N{sub 4} as a support and silver nitrate as a precursor. X-ray diffraction, Fourier transform infrared spectroscopy, X-ray photoelectron spectroscopy, transmission electron microscopy, and elemental mapping demonstrated that β-Ag{sub 2}WO{sub 4} nanoparticles were evenly distributed on the surface of g-C{sub 3}N{sub 4} nanosheets, which acted as a support for the nucleation and growth of β-Ag{sub 2}WO{sub 4} and inhibited the phase transformation of metastable β-Ag{sub 2}WO{sub 4} to stable α-Ag{sub 2}WO{sub 4}. Photocatalytic experiments indicated that the g-C{sub 3}N{sub 4}/Ag{sub 2}WO{sub 4} nanocomposite photocatalyst displayed a better photocatalytic activity than pure g-C{sub 3}N{sub 4} and Ag{sub 2}WO{sub 4} toward the degradation of methyl orange. The enhanced photocatalytic performance of g-C{sub 3}N{sub 4}/Ag{sub 2}WO{sub 4} could be well explained by a direct Z-scheme photocatalytic mechanism. This mechanism was related to the efficient space separation of photogenerated electron–hole pairs and the great oxidation and reduction capabilities of the g-C{sub 3}N{sub 4}/Ag{sub 2}WO{sub 4} system. This work provided new insights into the design and fabrication of g-C{sub 3}N{sub 4}-based direct Z-scheme photocatalysts.

  9. Enhanced photocatalytic properties in well-ordered mesoporous WO3

    KAUST Repository

    Li, Li; Krissanasaeranee, Methira; Pattinson, Sebastian W.; Stefik, Morgan; Wiesner, Ulrich; Steiner, Ullrich; Eder, Dominik

    2010-01-01

    We used polyisoprene-block-ethyleneoxide copolymers as structure-directing agents to synthesise well-ordered and highly-crystalline mesoporous WO 3 architectures that possess improved photocatalytic properties due to enhanced dye-adsorption in absence of diffusion limitation. © 2010 The Royal Society of Chemistry.

  10. Electronic structure and magnetic properties of FeWO{sub 4} nanocrystals synthesized by the microwave-hydrothermal method

    Energy Technology Data Exchange (ETDEWEB)

    Almeida, M.A.P. [INCTMN-DQ-Universidade Federal de Sao Carlos, Sao Carlos, P.O. Box 676, 13565-905, SP (Brazil); Cavalcante, L.S., E-mail: laeciosc@bol.com.br [INCTMN-Universidade Estadual, Paulista, P.O. Box 355, 14801-907, Araraquara, SP (Brazil); Morilla-Santos, C.; Filho, P.N. Lisboa [MAv-Universidade Estadual, Paulista, P.O. Box 473, 17033-360, Bauru, SP (Brazil); Beltran, A.; Andres, J.; Gracia, L. [Department de Quimica Fisica i Analitica, Universitat Jaume I, E-12071 Castello (Spain); Longo, E. [INCTMN-DQ-Universidade Federal de Sao Carlos, Sao Carlos, P.O. Box 676, 13565-905, SP (Brazil); INCTMN-Universidade Estadual, Paulista, P.O. Box 355, 14801-907, Araraquara, SP (Brazil)

    2012-11-15

    This communication reports that FeWO{sub 4} nanocrystals were successfully synthesized by the microwave-hydrothermal method at 443 K for 1 h. The structure and shape of these nanocrystals were characterized by X-ray diffraction, Rietveld refinement, and transmission electron microscopy. The experimental results and first principles calculations were combined to explain the electronic structure and magnetic properties. Experimental data were obtained by magnetization measurements for different applied magnetic fields. Theoretical calculations revealed that magnetic properties of FeWO{sub 4} nanocrystals can be assigned to two magnetic orderings with parallel or antiparallel spins in adjacent chains. These factors are crucial to understanding of competition between ferro- and antiferromagnetic behavior. Highlights: Black-Right-Pointing-Pointer Monophasic FeWO{sub 4} nanocrystals were synthesized by the microwave-hydrothermal method. Black-Right-Pointing-Pointer Rietveld refinement and clusters model for monoclinic structure Black-Right-Pointing-Pointer Magnetic properties of FeWO{sub 4} nanocrystals at different temperatures.

  11. Physical characteristic and irritation index of Syzigium aromaticum essential oil in O/W and W/O creams

    Science.gov (United States)

    Safriani, R.; Sugihartini, N.; Yuliani, S.

    2017-11-01

    Essential oil of Syzigium aromaticum has been formulated in O/W and W/O creams as anti-inflammatory dosage form. The purpose of this study was to evaluate the physical characteristic and irritation index of S. aromaticum essential oil in O/W and W/O creams. The creams were made by fusion method. The creams then were evaluated the physical characteristic including pH, viscosity, spreadability and adhesivity. The irritation index was obtained by irritation skin test in male rabbit. The results showed that the W/O and O/W creams have the value of pH: 6.3 and 6.27; spreadability: 3,18 and 4.17 cm2; adhesivity: 5.59 and 0.07 minutes; viscosity: 4.43 and 2.88 Pa.S, respectively. The irritation test showed that the control enhancer caused mild irritation in both of W/O and O/W creams. These findings indicated that type of cream might influence the physical characteristic and irritation index of S. aromaticum essential oil cream.

  12. Enhanced electrochromic and energy storage performance in mesoporous WO3 film and its application in a bi-functional smart window.

    Science.gov (United States)

    Wang, Wei-Qi; Wang, Xiu-Li; Xia, Xin-Hui; Yao, Zhu-Jun; Zhong, Yu; Tu, Jiang-Ping

    2018-05-03

    Construction of multifunctional photoelectrochemical energy devices is of great importance to energy saving. In this study, we have successfully prepared a mesoporous WO3 film on FTO glass via a facile dip-coating sol-gel method; the designed mesoporous WO3 film exhibited advantages including high transparency, good adhesion and high porosity. Also, multifunctional integrated energy storage and optical modulation ability are simultaneously achieved by the mesoporous WO3 film. Impressively, the mesoporous WO3 film exhibits a noticeable electrochromic energy storage performance with a large optical modulation up to 75.6% at 633 nm, accompanied by energy storage with a specific capacity of 75.3 mA h g-1. Furthermore, a full electrochromic energy storage window assembled with the mesoporous WO3 anode and PANI nanoparticle cathode is demonstrated with large optical modulation and good long-term stability. Our research provides a new route to realize the coincident utilization of optical-electrochemical energy.

  13. A novel nitrite biosensor based on the direct electron transfer hemoglobin immobilized in the WO3 nanowires with high length–diameter ratio

    International Nuclear Information System (INIS)

    Liu, Hui; Duan, Congyue; Yang, Chenhui; Chen, Xianjin; Shen, Wanqiu; Zhu, Zhenfeng

    2015-01-01

    WO 3 nanowires (WO 3 NWs) with high length–diameter ratio have been synthesized through a simple synthetic route without any additive and then used to immobilize hemoglobin (Hb) to fabricate a mediator-free biosensor. The morphology and structure of WO 3 NWs were characterized by scanning electron microscopy, transmission electronic microscopy and X-ray diffraction. Spectroscopic and electrochemical results revealed that WO 3 NWs are an excellent immobilization matrix with biocompatibility for redox protein, affording good protein bioactivity and stability. Meanwhile, due to unique morphology and property of the WO 3 nanowires, the direct electron transfer of Hb is facilitated and the prepared biosensors displayed good performance for the detection of nitrite with a wide linear range of 1 to 4200 μM, as well as an extremely low detection limit of 0.28 μM. The WO 3 nanowires with high length–diameter ratio could be a promising matrix for the fabrication of mediator-free biosensors, and may find wide potential applications in environmental analysis and biomedical detection. - Highlights: • The WO 3 NWs with high length–diameter ratio have been synthesized. • The WO 3 NWs were used to immobilize Hb to fabricate a mediator-free biosensor. • The biosensor displays a wide linear range of 1–4200 μM for nitrite. • The biosensor exhibits an extremely low detection limit of 0.28 μM for nitrite

  14. Structural Precast Concrete Handbook

    DEFF Research Database (Denmark)

    Kjærbye, Per Oluf H

    Structural concept for precast concrete systems. Design og precast reinforced concrete components. Design of precast concrete connections. Illustrations on design of precast concrete buildings. Precast concrete assembly.......Structural concept for precast concrete systems. Design og precast reinforced concrete components. Design of precast concrete connections. Illustrations on design of precast concrete buildings. Precast concrete assembly....

  15. COMPARATIVE STUDY OF GLASS FIBRE CONCRETE AND NORMAL CONCRETE

    OpenAIRE

    Mr.Yogesh S.Lanjewar*

    2018-01-01

    Concrete is basically the most important material concerning with the construction and infrastructural procedures, for which it should be of good strength and durability. Many researches are being conducted to make concrete more sustainable and of more strength and durability. Therefore keeping this in mind i have chosen to do the comparative study regarding the strength of normal concrete with the glass fibre added concrete using mix design procedure as per IS 10262-2009 for concrete. As w...

  16. Study of technological features of tubular compressed concrete members in concreting

    Directory of Open Access Journals (Sweden)

    Voskobiinyk Olena

    2017-01-01

    Full Text Available The technological features of core concreting were analyzed as the main factor in ensuring of strength and reliability of compressed concrete-filled steel tubular (CFST members. We have conducted the analysis of existing concreting methods of CFST members. In this respect, the most dangerous types of possible technological defects of concrete core of CFST members are inhomogeneity along the height, voids, caverns, and concrete “weak spots”. The authors considered the influence of such technological factors of concreting: placeability, time, concrete mixture compaction method, concreting height on the concrete core strength of CFST members. Based on the experimental studies conducted we suggested the regression correlations for determining the concrete strength of CFST members of different length depending on the movability of concrete mixture and a time for its compaction. The authors performed the correlation analysis of technological factors of concreting on the strength of the concrete core. We carried out the comparison of data on the concrete core strength of CFST members, that were determined by non-destructive methods (sclerometer test results, ultrasonic method and direct compression strength tests. We experimentally proved that using movable mixtures with the slump of about 4 – 9 cm the overall variation coefficient of concrete core strength of CFST members along the height reaches nearly 13%. Based on the experimental studies conducted we suggested the guidelines on optimal regimes of concrete compaction during manufacturing CFST members at a construction site environment.

  17. FY1995 development of economical and high efficient desulfurization process using low rank coal; 1995 nendo teitankadotan wo mochiita ankana kokoritsu datsuryuho no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    The objective of this study is to develop a new efficient desulfurization technique using a Ca ion-exchanged coal prepared from low rank coal and calcium raw material as a SO{sub 2} sorbent. Ion-exchange of calcium was carried out by soaking and mixing brown coal particles in milk of lime or slurry of industrial waste from concrete manufacture process. About 10wt% of Ca was easily incorporated into Yallourn coal. The ion-exchanged Ca was transformed to ultra-fine CaO particles upon pyrolysis of coal. The reactivity of CaO produced from Ca-exchanged coal to SO{sub 2} was extraordinary high and the CaO utilization of above 90% was easily achieved, while the conversion of natural limestone was less than 30% under the similar experimental conditions. High activity of Ca-exchanged coal was appreciably observed in a pressurized fluidized bed combustor. Ca-exchanged coal was quite effective for the removal of hydrogen sulfide. (NEDO)

  18. Glazed Concrete

    DEFF Research Database (Denmark)

    Bache, Anja Margrethe

    2010-01-01

    Why glazed concrete? Concrete hardens and finds its strength at room temperature whereas clay products must first be fired before they achieve this strength. They are stronger and three times as durable as clay products, which is a weighty reason for choosing concrete.5 Another reason, which....... If this succeeds, it will be possible to manufacture thin, large-scale glazed concrete panels comparable in size to concrete sandwich construction and larger which, with or without back-casting, can work as load-bearing construction elements....

  19. Properties of concretes produced with waste concrete aggregate

    International Nuclear Information System (INIS)

    Topcu, Ilker Bekir; Sengel, Selim

    2004-01-01

    An environmentally friendly approach to the disposal of waste materials, a difficult issue to cope with in today's world, would only be possible through a useful recycling process. For this reason, we suggest that clearing the debris from destroyed buildings in such a way as to obtain waste concrete aggregates (WCA) to be reused in concrete production could well be a partial solution to environmental pollution. For this study, the physical and mechanical properties along with their freeze-thaw durability of concrete produced with WCAs were investigated and test results presented. While experimenting with fresh and hardened concrete, mixtures containing recycled concrete aggregates in amounts of 30%, 50%, 70%, and 100% were prepared. Afterward, these mixtures underwent freeze-thaw cycles. As a result, we found out that C16-quality concrete could be produced using less then 30% C14-quality WCA. Moreover, it was observed that the unit weight, workability, and durability of the concretes produced through WCA decreased in inverse proportion to their endurance for freeze-thaw cycle

  20. Concrete Hinges

    DEFF Research Database (Denmark)

    Halding, Philip Skov; Hertz, Kristian Dahl; Schmidt, Jacob Wittrup

    2014-01-01

    In the first part of the 20th century concrete hinges developed by Freyssinet and Mesnager were widely tested and implemented in concrete structures. The concrete hinges were used a great deal in closed-spandrel arch bridges. Since such a bridge type has not been competitive for the past 40 years......, the research in concrete hinges has not evolved significantly in that period. But introducing a new state-of-the-art concrete arch bridge solution (Pearl-Chain arches invented at the Technical University of Denmark) creates a necessity of a concrete hinge research based on modern standards. Back when research...... in concrete hinges was more common different designs were proposed for the geometry and reinforcement. Previous research focused on fatigue, multi-axial stresses around the hinge throat, and the relation between rotation- and moment. But many different test-setups were proposed by different researchers...

  1. Per-service supervised learning for identifying desired WoT apps from user requests in natural language.

    Directory of Open Access Journals (Sweden)

    Young Yoon

    Full Text Available Web of Things (WoT platforms are growing fast so as the needs for composing WoT apps more easily and efficiently. We have recently commenced the campaign to develop an interface where users can issue requests for WoT apps entirely in natural language. This requires an effort to build a system that can learn to identify relevant WoT functions that fulfill user's requests. In our preceding work, we trained a supervised learning system with thousands of publicly-available IFTTT app recipes based on conditional random fields (CRF. However, the sub-par accuracy and excessive training time motivated us to devise a better approach. In this paper, we present a novel solution that creates a separate learning engine for each trigger service. With this approach, parallel and incremental learning becomes possible. For inference, our system first identifies the most relevant trigger service for a given user request by using an information retrieval technique. Then, the learning engine associated with the trigger service predicts the most likely pair of trigger and action functions. We expect that such two-phase inference method given parallel learning engines would improve the accuracy of identifying related WoT functions. We verify our new solution through the empirical evaluation with training and test sets sampled from a pool of refined IFTTT app recipes. We also meticulously analyze the characteristics of the recipes to find future research directions.

  2. Per-service supervised learning for identifying desired WoT apps from user requests in natural language.

    Science.gov (United States)

    Yoon, Young

    2017-01-01

    Web of Things (WoT) platforms are growing fast so as the needs for composing WoT apps more easily and efficiently. We have recently commenced the campaign to develop an interface where users can issue requests for WoT apps entirely in natural language. This requires an effort to build a system that can learn to identify relevant WoT functions that fulfill user's requests. In our preceding work, we trained a supervised learning system with thousands of publicly-available IFTTT app recipes based on conditional random fields (CRF). However, the sub-par accuracy and excessive training time motivated us to devise a better approach. In this paper, we present a novel solution that creates a separate learning engine for each trigger service. With this approach, parallel and incremental learning becomes possible. For inference, our system first identifies the most relevant trigger service for a given user request by using an information retrieval technique. Then, the learning engine associated with the trigger service predicts the most likely pair of trigger and action functions. We expect that such two-phase inference method given parallel learning engines would improve the accuracy of identifying related WoT functions. We verify our new solution through the empirical evaluation with training and test sets sampled from a pool of refined IFTTT app recipes. We also meticulously analyze the characteristics of the recipes to find future research directions.

  3. Characterization of nanoparticles of lidocaine in w/o microemulsions ...

    Indian Academy of Sciences (India)

    drophilic phase and a hydrophobic phase, stabilized with the use of surfactants. Regular MEs consist of nanometer-sized hydrocarbon domains (termed micelles) surrounded by amphiphilic molecules, stabilized in a continuous aqueous phase. In contrast, reverse (w/o) MEs consist of aqueous domains (termed reverse ...

  4. Polarized spectroscopic properties of Nd3+-doped KGd(WO4)2 single crystal

    International Nuclear Information System (INIS)

    Chen Yujin; Lin Yanfu; Gong Xinghong; Tan Qiguang; Zhuang Jian; Luo Zundu; Huang Yidong

    2007-01-01

    The polarized absorption spectra, infrared fluorescence spectra, upconversion visible fluorescence spectra, and fluorescence decay curve of orientated Nd 3+ :KGd(WO 4 ) 2 crystal were measured at room-temperature. Some important spectroscopic parameters were investigated in detail in the framework of the Judd-Ofelt theory and the Fuchtbauer-Ladenburg formula. The effect of the crystal structure on the spectroscopic properties of the Nd 3+ ions was analyzed. The relation among the spectroscopic parameters and the laser performances of the Nd 3+ :KGd(WO 4 ) 2 crystal was discussed

  5. Significance of tests and properties of concrete and concrete-making materials

    CERN Document Server

    Pielert, James H

    2006-01-01

    Reflects a decade of technological changes in concrete industry! The newest edition of this popular ASTM publication reflects the latest technology in concrete and concrete-making materials. Six sections cover: (1) General information on the nature of concrete, sampling, variability, and testing laboratories. A new chapter deals with modeling cement and concrete properties. (2) Properties of freshly mixed concrete. (3) Properties of hardened concrete. (4) Concrete aggregates—this section has been revised and the chapters are presented in the order that most concerns concrete users: grading, density, soundness, degradation resistance, petrographic examination, reactivity, and thermal properties. (5) Materials other than aggregates—the chapter on curing materials now reflects the current technology of materials applied to new concrete surfaces. The chapter on mineral admixtures has been separated into two chapters: supplementary cementitious materials and ground slag. (6) Specialized concretes—contains a ...

  6. Design of ultra-lightweight concrete: towards monolithic concrete structures

    Directory of Open Access Journals (Sweden)

    Yu Qing Liang

    2014-04-01

    Full Text Available This study addresses the development of ultra-lightweight concrete. A moderate strength and an excellent thermal conductivity of the lightweight concrete are set as the design targets. The designed lightweight aggregates concrete is targeted to be used in monolithic concrete façade structure, performing as both load bearing element and thermal insulator. The developed lightweight concrete shows excellent thermal properties, with a low thermal conductivity of about 0.12 W/(m·K; and moderate mechanical properties, with 28-day compressive strengths of about 10-12 N/mm . This combination of values exceeds, to the researchers’ knowledge, the performance of all other lightweight building materials. Furthermore, the developed lightweight concrete possesses excellent durability properties.

  7. Sol-gel synthesis of Bi2WO6/graphene thin films with enhanced photocatalytic performance for nitric monoxide oxidation under visible light irradiation

    Science.gov (United States)

    Sun, Chufeng; Wang, Yanbin; Su, Qiong

    2018-06-01

    Bi2WO6 and Bi2WO6/graphene thin films were fabricated by spin coating and post annealing at 600 °C for 2 h. In four different thin film samples, the graphene concentration was controlled as 0, 2, 4 and 6 wt%, respectively. The morphology, grain size and elemental distribution of the thin films were characterized by SEM and TEM. The crystallization and crystal phases were determined by XRD patterns, and the existence of graphene in Bi2WO6/graphene composite thin films were confirmed by Raman spectra. The photocatalytic performance of Bi2WO6 and Bi2WO6/graphene thin films was investigated by oxidizing NO under visible light irradiation. The results showed that Bi2WO6/graphene with 4 wt% of graphene showed the highest photocatalytic performance among all samples. This could be attributed to the increased electron conductivity with the presence of graphene. However, a further increased graphene concentration resulted in a decreased photocatalytic performance.

  8. Concrete structures

    CERN Document Server

    Setareh, Mehdi

    2017-01-01

    This revised, fully updated second edition covers the analysis, design, and construction of reinforced concrete structures from a real-world perspective. It examines different reinforced concrete elements such as slabs, beams, columns, foundations, basement and retaining walls and pre-stressed concrete incorporating the most up-to-date edition of the American Concrete Institute Code (ACI 318-14) requirements for the design of concrete structures. It includes a chapter on metric system in reinforced concrete design and construction. A new chapter on the design of formworks has been added which is of great value to students in the construction engineering programs along with practicing engineers and architects. This second edition also includes a new appendix with color images illustrating various concrete construction practices, and well-designed buildings. The ACI 318-14 constitutes the most extensive reorganization of the code in the past 40 years. References to the various sections of the ACI 318-14 are pro...

  9. Comparative investigation of the Ti and Mo additives influence on the opto-electronic properties of the spray deposited WO{sub 3} thin films

    Energy Technology Data Exchange (ETDEWEB)

    Manceriu, Laura Maria, E-mail: manceriu.laura@gmail.com [CNRS, Université de Bordeaux, ICMCB, 87 Avenue du Dr. Albert Schweitzer, F-33608 Pessac (France); The RTD Dept. Renewable Energy Systems and Recycling, University of Transilvania Brasov, Eroilor 29, 500036 Brasov (Romania); Rougier, Aline [CNRS, Université de Bordeaux, ICMCB, 87 Avenue du Dr. Albert Schweitzer, F-33608 Pessac (France); Duta, Anca, E-mail: a.duta@unitbv.ro [The RTD Dept. Renewable Energy Systems and Recycling, University of Transilvania Brasov, Eroilor 29, 500036 Brasov (Romania)

    2015-05-05

    Highlights: • Ti and Mo–WO{sub 3} thin films were obtained by spray pyrolysis. • Morphology and structure changes related to solution surface tension modification. • FTO/WO{sub 3} junction parameters dependent on WO{sub 3} layer morphology and structure. • Flat band potential and series resistance varied with cation doping. • Ad(de)sorption of oxygen/water during annealing and cooling influence conductivity. - Abstract: In this paper we compare the optical and electrical properties of the WO{sub 3} thin films containing 2, 5 and 10 at.% of Ti and Mo additives, deposited by spray pyrolysis. The influence of the type and additive concentration on the nanostructure, topography and composition of the WO{sub 3} layers are mainly related to the surface tension energy changes, and further correlated with the (photo)electrical and optical properties. The FTO/WO{sub 3} junction through its characteristic, namely barrier height, ideality factor, flat band potential, and series resistance, served as a tool for associating the before mentioned characteristics. The morphology of the WO{sub 3} thin films densifies and the roughness is reduced with increasing Ti and Mo concentration, in good agreement with solution surface tension reduction. WO{sub 3} based films exhibit a p-type semiconducting behavior, as confirmed also by the Mott–Schottky analysis, with a lower p-type conductivity for the Ti–WO{sub 3} films, as higher number of oxygen vacancies are generated by Ti addition. Changes in conductivity are mainly attributed to the oxygen vacancies concentration evolution at the film surface due to oxygen/water adsorption. For heavily doped WO{sub 3} thin films the contribution of these surface processes to the overall conductivity is reduced since surface reactivity is lost by densification. As opposed to Ti-doping which has a detrimental effect on layers structure, Mo addition, even in high concentrations, has a positive effect on layers crystallinity; hence

  10. Preparation of Porous F-WO3/TiO2 Films with Visible-Light Photocatalytic Activity by Microarc Oxidation

    OpenAIRE

    Yeh, Chung-Wei; Wu, Kee-Rong; Hung, Chung-Hsuang; Chang, Hao-Cheng; Hsu, Chuan-Jen

    2012-01-01

    Porous F-WO3/TiO2 (mTiO2) films are prepared on titanium sheet substrates using microarc oxidation (MAO) technique. The X-ray diffraction patterns show that visible-light (Vis) enabling mTiO2 films with a very high content of anatase TiO2 and high loading of WO3 are successfully synthesized at a low applied voltage of 300 V using electrolyte contenting NaF and Na2WO4 without subsequent heat treatment. The cross-sectional transmission electron microscopy micrograph reveals that the mTiO2 films...

  11. Negative thermal expansion in Sc2(WO4)3

    International Nuclear Information System (INIS)

    Evans, J.S.O.; Mary, T.A.; Sleight, A.W.

    1998-01-01

    Sc 2 (WO 4 ) 3 has been found to show the highly unusual property of negative thermal expansion over a temperature range of 10 to 1,073 K. Powder neutron diffraction data from 10 to 450 K shows an essentially linear decrease in cell volume as a function of temperature. The intrinsic linear coefficient of thermal expansion from this data is -2.2 x 10 -6 K -1 . The linear coefficient of thermal expansion measured on a ceramic bar of Sc 2 (WO 4 ) 3 can be as negative as -11 x 10 -6 K -1 due to microstructure changes as a function of temperature. Rietveld refinement as a function of temperature suggests that the intrinsic negative thermal expansion can be related to transverse vibrations of bridging oxygen atoms in the structure. The anharmonic nature of these vibrations leads to a coupled tilting of the quasi-rigid framework polyhedra. This tilting in turn causes the structure to become more dense with increasing temperature

  12. Efficient visible-light photocatalytic and enhanced photocorrosion inhibition of Ag2WO4 decorated MoS2 nanosheets

    Science.gov (United States)

    Thangavel, Sakthivel; Thangavel, Srinivas; Raghavan, Nivea; Alagu, Raja; Venugopal, Gunasekaran

    2017-11-01

    The use of two-dimensional nanomaterials as co-catalysts in the photodegradation of toxic compounds using light irradiation is an attractive ecofriendly process. In this study, we prepared a novel MoS2/Ag2WO4 nanohybrid via a one-step hydrothermal approach and the photocatalytic properties were investigated by the degradation of methyl-orange under stimulated irradiation. The nanohybrid exhibits enhanced efficiency in dye degradation compared to the bare Ag2WO4 nanorods; the same has been evidently confirmed with UV-visible spectra and total organic carbon removal analysis. The pseudo-first order rate constant of the nanohybrid is nearly 1.8 fold higher than that of the bare Ag2WO4 nanorods. With the aid of classical radical quenching and photoluminescence spectral analysis, a reasonable mechanism has been derived for the addition of MoS2 to nanohybrids to enhance the photocatalytic efficiency. MoS2 prevents photocorrosion of Ag2WO4 and also diminishes the number of photogenerated electron-hole recombination. Our findings could provide new insights in understanding the mechanism of the MoS2/Ag2WO4 nanohybrid as an efficient photocatalyst suitable for waste-water treatment and remedial applications.

  13. Promotion effect of Pt on a SnO2-WO3 material for NOx sensing

    Science.gov (United States)

    Wang, Chen-Yang; Hong, Zih-Siou; Wu, Ren-Jang

    2015-05-01

    Metal-oxide nanocomposites were prepared over screen-printed gold electrodes to be used as room-temperature NOx (nitric-oxide (NO) and nitrogen dioxide (NO2)) sensors. Various weight ratios of SnO2-WO3 and Pt loadings were used for NO sensing. The sensing materials were characterized using X-ray diffraction (XRD), transmission electron microscopy (TEM) and BET surface analysis. The NO-sensing results indicated that SnO2-WO3 (1:2) was more effective than other materials were. The sensor response (S=resistance of N2/resistance of NO=RN2/RNO) for detecting 1000 ppm of NO at room temperature was 2.6. The response time (T90) and recovery time (TR90) was 40 s and 86 s, respectively. By further loading with 0.5% Pt, the sensor response increased to 3.3. The response and recovery times of 0.5% Pt/SnO2-WO3 (1:2) were 40 s and 206 s, respectively. The linearity of the sensor response for a NO concentration range of 10-1000 ppm was 0.9729. A mechanism involving Pt promotion of the SnO2-WO3 heterojunction was proposed for NO adsorption, surface reaction, and adsorbed NO2 desorption.

  14. A facile fabrication of plasmonic g-C{sub 3}N{sub 4}/Ag{sub 2}WO{sub 4}/Ag ternary heterojunction visible-light photocatalyst

    Energy Technology Data Exchange (ETDEWEB)

    Dai, Kai, E-mail: daikai940@chnu.edu.cn [College of Physics and Electronic Information, Huaibei Normal University, Huaibei, 235000 (China); Lv, Jiali [College of Physics and Electronic Information, Huaibei Normal University, Huaibei, 235000 (China); Lu, Luhua, E-mail: lhlu@cug.edu.cn [Faculty of Material Science and Chemical Engineering, China University of Geosciences, Wuhan, 430074 (China); Liang, Changhao [College of Physics and Electronic Information, Huaibei Normal University, Huaibei, 235000 (China); Key Laboratory of Materials Physics and Anhui Key Laboratory of Nanomaterials and Nanotechnology, Institute of Solid State Physics, Hefei Institutes of Physical Science, Chinese Academy of Sciences, Hefei, 230031 (China); Geng, Lei; Zhu, Guangping [College of Physics and Electronic Information, Huaibei Normal University, Huaibei, 235000 (China)

    2016-07-01

    It's important to reduce recombination of electrons and holes and enhance charge transfer through fine controlled interfacial structure. In this work, novel graphitic-C{sub 3}N{sub 4} (g-C{sub 3}N{sub 4})/Ag{sub 2}WO{sub 4}/Ag ternary photocatalyst has been synthesized by deposition of Ag{sub 2}WO{sub 4} onto g-C{sub 3}N{sub 4} template and followed by sun light reduction of Ag{sub 2}WO{sub 4} into Ag{sub 2}WO{sub 4}/Ag. As-prepared g-C{sub 3}N{sub 4}/Ag{sub 2}WO{sub 4}/Ag presented significantly enhanced photocatalytic performance in degrading methylene blue (MB) under 410 nm LED light irradiation. Metallic Ag{sup 0} is used as plasmonic hot spots to generate high energy charge carriers. Optimal g-C{sub 3}N{sub 4} content has been confirmed to be 40 wt%, corresponding to apparent pseudo-first-order rate constant kapp of 0.0298 min{sup −1}, which is 3.3 times and 37.3 times more than that of pure g-C{sub 3}N{sub 4} and Ag{sub 2}WO{sub 4}, respectively. This novel ternary g-C{sub 3}N{sub 4}/Ag{sub 2}WO{sub 4}/Ag structure material is an ideal candidate in environmental treatment and purifying applications. - Graphical abstract: A high efficient plasmonic graphitic-C{sub 3}N{sub 4}/Ag{sub 2}WO{sub 4}/Ag ternary nanocomposite photocatalyst was synthesized. - Highlights: • g-C{sub 3}N{sub 4}/Ag{sub 2}WO{sub 4}/Ag ternary nanocomposite photocatalyst was prepared. • g-C{sub 3}N{sub 4}/Ag{sub 2}WO{sub 4}/Ag showed high photocatalytic activity. • g-C{sub 3}N{sub 4}/Ag{sub 2}WO{sub 4}/Ag showed long reusable life.

  15. A novel nitrite biosensor based on the direct electron transfer hemoglobin immobilized in the WO{sub 3} nanowires with high length–diameter ratio

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Hui, E-mail: liuhui@sust.edu.cn; Duan, Congyue; Yang, Chenhui; Chen, Xianjin; Shen, Wanqiu; Zhu, Zhenfeng

    2015-08-01

    WO{sub 3} nanowires (WO{sub 3}NWs) with high length–diameter ratio have been synthesized through a simple synthetic route without any additive and then used to immobilize hemoglobin (Hb) to fabricate a mediator-free biosensor. The morphology and structure of WO{sub 3}NWs were characterized by scanning electron microscopy, transmission electronic microscopy and X-ray diffraction. Spectroscopic and electrochemical results revealed that WO{sub 3}NWs are an excellent immobilization matrix with biocompatibility for redox protein, affording good protein bioactivity and stability. Meanwhile, due to unique morphology and property of the WO{sub 3} nanowires, the direct electron transfer of Hb is facilitated and the prepared biosensors displayed good performance for the detection of nitrite with a wide linear range of 1 to 4200 μM, as well as an extremely low detection limit of 0.28 μM. The WO{sub 3} nanowires with high length–diameter ratio could be a promising matrix for the fabrication of mediator-free biosensors, and may find wide potential applications in environmental analysis and biomedical detection. - Highlights: • The WO{sub 3}NWs with high length–diameter ratio have been synthesized. • The WO{sub 3}NWs were used to immobilize Hb to fabricate a mediator-free biosensor. • The biosensor displays a wide linear range of 1–4200 μM for nitrite. • The biosensor exhibits an extremely low detection limit of 0.28 μM for nitrite.

  16. Silver loaded WO{sub 3-x}/TiO{sub 2} composite multifunctional thin films

    Energy Technology Data Exchange (ETDEWEB)

    Dunnill, Charles W.; Noimark, Sacha; Parkin, Ivan P., E-mail: I.P.Parkin@ucl.ac.uk

    2012-06-30

    Multifunctional WO{sub 3-x}-TiO{sub 2} composite thin films have been prepared by sol-gel synthesis and shown to be good visible light photocatalysts whilst retaining a desirable underlying blue colouration. The WO{sub 3-x}-TiO{sub 2} composite thin films were further enhanced using silver nanoparticles synthesised in-situ on the surface from the photo-degradation of silver nitrate solution. Thin films were characterised using X-ray diffraction, Raman, Scanning electron microscopy and UV-visible spectroscopy and shown to photo degrade stearic acid, using white light {lambda} = 420-800 nm. - Highlights: Black-Right-Pointing-Pointer WO{sub 3-X} TiO{sub 2} composite thin films were synthesised by sol-gel methods. Black-Right-Pointing-Pointer Blue tinted glass is desirable for the value added glass industry. Black-Right-Pointing-Pointer Silver nanoparticle island formation enhances the activity of the films. Black-Right-Pointing-Pointer Blue tinted 'value added' coated glass is now possible.

  17. Fibre Concrete 2017

    Science.gov (United States)

    2017-09-01

    9th international conference on fibre reinforced concretes (FRC), textile reinforced concretes (TRC) and ultra-high performance concretes (UHPC) Preface The Fibre Concrete Conference series is held biennially to provide a platform to share knowledge on fibre reinforced concretes, textile concretes and ultra-high performance concretes regarding material properties and behaviour, technology procedures, topics of long-term behaviour, creep, durability; sustainable aspects of concrete including utilisation of waste materials in concrete production and recycling of concrete. The tradition of Fibre Concrete Conferences started in eighties of the last century. Nowadays the conference is organized by the Department of Concrete and Masonry Structures of the Czech Technical University in Prague, Faculty of Civil Engineering. The 9th International Conference Fibre Concrete 2017 had 109 participants from 27 countries all over the world. 55 papers were presented including keynote lectures of Professor Bažant, Professor Bartoš and Dr. Broukalová. The conference program covered wide range of topics from scientific research to practical applications. The presented contributions related to performance and behaviour of cement based composites, their long-term behaviour and durability, sustainable aspects, advanced analyses of structures from these composites and successful applications. This conference was organized also to honour Professor Zděnek P. Bažant on the occasion of his jubilee and to appreciate his merits and discoveries in the field of fibre reinforced composites, structural mechanics and engineering.

  18. AC conductivity and dielectric properties of bulk tungsten trioxide (WO3)

    Science.gov (United States)

    El-Nahass, M. M.; Ali, H. A. M.; Saadeldin, M.; Zaghllol, M.

    2012-11-01

    AC conductivity and dielectric properties of tungsten trioxide (WO3) in a pellet form were studied in the frequency range from 42 Hz to 5 MHz with a variation of temperature in the range from 303 K to 463 K. AC conductivity, σac(ω) was found to be a function of ωs where ω is the angular frequency and s is the frequency exponent. The values of s were found to be less than unity and decrease with increasing temperature, which supports the correlated barrier hopping mechanism (CBH) as the dominant mechanism for the conduction in WO3. The dielectric constant (ε‧) and dielectric loss (ε″) were measured. The Cole-Cole diagram determined complex impedance for different temperatures.

  19. Gas Sensing Properties of Metal Doped WO3 Thin Film Sensors Prepared by Pulsed Laser Deposition and DC Sputtering Process

    Science.gov (United States)

    Bhuiyan, Md. Mosharraf Hossain; Ueda, Tsuyoshi; Ikegami, Tomoaki; Ebihara, Kenji

    2006-10-01

    Tungsten trioxide (WO3) thin films gas sensors were prepared by the KrF excimer pulsed laser deposition (PLD) method. The films were prepared on the quartz glass, silicon and also on the Al2O3 sensor substrates with platinum interdigitated electrodes. The effect of doping of the platinum (Pt), palladium (Pd) or gold (Au) on the WO3 thin film was also investigated. These metals were doped to the WO3 thin film by the DC sputtering process during the PLD. The substrate temperature and the oxygen pressure were 400 °C and 100 mTorr, respectively, during the deposition. The films were characterized by atomic force microscopy (AFM) and X-ray diffraction (XRD). The sensitivity of the prepared sensors to 60 ppm NO gas was examined using the two terminal resistance method in a chamber at atmospheric pressure and operating temperatures of 25-350 °C. The sensitivity of the WO3 thin films doped with Pt, Pd, or Au was found to be higher than that of the undoped WO3 thin film.

  20. Abnormal network flow detection based on application execution patterns from Web of Things (WoT) platforms.

    Science.gov (United States)

    Yoon, Young; Jung, Hyunwoo; Lee, Hana

    2018-01-01

    In this paper, we present a research work on a novel methodology of identifying abnormal behaviors at the underlying network monitor layer during runtime based on the execution patterns of Web of Things (WoT) applications. An execution pattern of a WoT application is a sequence of profiled time delays between the invocations of involved Web services, and it can be obtained from WoT platforms. We convert the execution pattern to a time sequence of network flows that are generated when the WoT applications are executed. We consider such time sequences as a whitelist. This whitelist reflects the valid application execution patterns. At the network monitor layer, our applied RETE algorithm examines whether any given runtime sequence of network flow instances does not conform to the whitelist. Through this approach, it is possible to interpret a sequence of network flows with regard to application logic. Given such contextual information, we believe that the administrators can detect and reason about any abnormal behaviors more effectively. Our empirical evaluation shows that our RETE-based algorithm outperforms the baseline algorithm in terms of memory usage.

  1. Concrete laying laboratory

    International Nuclear Information System (INIS)

    Bastlova, K.

    1986-01-01

    The task of the concrete laying laboratory established within a special department for quality control and assurance at the Dukovany nuclear power plant, is to check the composition of concrete mixes produced by the central concrete production plant on the site, and the shipment, laying and processing of concrete. The composition is given of special barite and serpentinite concretes designed for biological shields. The system of checks and of filing the results is briefly described. Esperience is summed up from the operation of the concrete laying laboratory, and conclusions are formulated which should be observed on similar large construction sites. They include the precise definition of the designer's requirements for the quality of concrete, the surface finish of concrete surfaces, the method of concreting specific structures around bushings, increased density reinforcements and various technological elements, and requirements for shipment to poorly accessible or remote places. As for the equipment of the laboratory, it should be completed with an instrument for the analysis of fresh concrete mixes, a large capacity drying kiln, etc. (Z.M.)

  2. A mesoporous WO{sub 3−X}/graphene composite as a high-performance Li-ion battery anode

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Fei [C-Industry Incubation Center, Korea Research Institute of Chemical Technology (KRICT), Daejeon 305-600 (Korea, Republic of); Kim, Jong Gu [C-Industry Incubation Center, Korea Research Institute of Chemical Technology (KRICT), Daejeon 305-600 (Korea, Republic of); Department of Fine Chemical Engineering and Applied Chemistry, Chungnam National University, Daejeon 305-764 (Korea, Republic of); Lee, Chul Wee [C-Industry Incubation Center, Korea Research Institute of Chemical Technology (KRICT), Daejeon 305-600 (Korea, Republic of); University of Science and Technology (UST), Gajeong-ro, Yuseong-gu, Daejeon 305-333 (Korea, Republic of); Im, Ji Sun, E-mail: jsim@krict.re.kr [C-Industry Incubation Center, Korea Research Institute of Chemical Technology (KRICT), Daejeon 305-600 (Korea, Republic of); University of Science and Technology (UST), Gajeong-ro, Yuseong-gu, Daejeon 305-333 (Korea, Republic of)

    2014-10-15

    Graphical abstract: The highly flexible and conductive graphene layer can enhance electron transfer, protect metal oxides against disintegration and aggregation and buffer the strain induced by volume expansion during cycles. The mesoporous surface layer provides an open network for Li+ diffusion. - Highlights: • Novel cocktail effects of 2D mesoporous WO{sub 3−X}/graphene for lithium ion battery. • New approach for lithium ion battery by easy and unique synthesis method. • Mechanism study with proper data for understanding a reaction on anode surface. - Abstract: A novel mesoporous WO{sub 3−X}/graphene composite was developed. This material allowed rapid electron and Li{sup +} ion diffusion when used as a Li-ion battery (LIB) anode material. Remarkably, the graphene support protected WO{sub 3−X} from changing volume during the electrochemical cycling process; this process generally induces capacity loss. The current work describes a high-performance anode material for LIB that has highly dense WO{sub 3−X}, as well as high capacity, rate capability and stability.

  3. Improvement of optical properties and radiation hardness of NaBi(WO sub 4) sub 2 Cherenkov crystals

    CERN Document Server

    Zadneprovski, B I; Polyansky, E V; Devitsin, E G; Kozlov, V A; Potashov, S Yu; Terkulov, A R

    2002-01-01

    On the basis of the data on melt evaporation while growing NaBi(WO sub 4) sub 2 Cherenkov crystals, the formation of nonstoichiometry and most probable types of dot defects of the crystals have been considered. The influence of melt nonstoichiometry and doping with Sc on optical transmission and radiation hardness of the crystals has been experimentally investigated. The surplus of WO sub 3 has been established to increase optical transmission and radiation hardness and lack of Bi sub 2 O sub 3 in the melt to reduce radiation hardness. Sc doping is shifting the absorption edge to UV region by 30-35 nm and is increasing radiation hardness of the crystals about three-fold. Analytical estimations give the increase of the number of Cherenkov photons by a factor of 1.3, which leads to an improvement of the energy resolution of a calorimeter based on NaBi(WO sub 4) sub 2 :Sc crystals compared with undoped NaBi(WO sub 4) sub 2 of approximately 15%.

  4. Concrete with onyx waste aggregate as aesthetically valued structural concrete

    Science.gov (United States)

    Setyowati E., W.; Soehardjono, A.; Wisnumurti

    2017-09-01

    The utillization of Tulungagung onyx stone waste as an aggregate of concrete mixture will improve the economic value of the concrete due to the brighter color and high aesthetic level of the products. We conducted the research of 75 samples as a test objects to measure the compression stress, splits tensile stress, flexural tensile stress, elasticity modulus, porosity modulus and also studied 15 test objects to identify the concrete micro structures using XRD test, EDAX test and SEM test. The test objects were made from mix designed concrete, having ratio cement : fine aggregate : coarse aggregate ratio = 1 : 1.5 : 2.1, and W/C ratio = 0.4. The 28 days examination results showed that the micro structure of Tulungagung onyx waste concrete is similar with normal concrete. Moreover, the mechanical test results proved that Tulungagung onyx waste concretes also have a qualified level of strength to be used as a structural concrete with higher aesthetic level.

  5. Pervious Concrete

    OpenAIRE

    Torsvik, Øyvind André Hoff

    2012-01-01

    Pervious concrete is a material with a high degree of permeability but generally low strength. The material is primarily used for paving applications but has shown promise in many other areas of usage. This thesis investigates the properties of pervious concrete using normal Norwegian aggregates and practices. An overview of important factors when it comes to designing and producing pervious concrete is the result of this investigation. Several experiments have been performed in the concrete ...

  6. Sustainable Concrete Technology

    Directory of Open Access Journals (Sweden)

    Sim J.

    2015-12-01

    Full Text Available The growing concern over global warming and significant ecological changes requires sustainable development in all fields of science and technology. Concrete not only consumes huge amount of energy and natural sources, but also emits large amount of CO2, mainly due to the production of cement. It is evident that such large amount of concrete production has put significant impact on the energy, resource, environment, and ecology of the society. Hence, how to develop the concrete technology in a sustainable way has become a significant issue. In this paper, some of Korean researches for sustainable development of concrete are presented. These are sustainable strengthening for deteriorated concrete structure, sustainable reinforcement of new concrete structure, sustainable concrete using recycled aggregate and supplementary cementing materials and finally application of each technique to precast concrete.

  7. Properties of concrete containing foamed concrete block waste as fine aggregate replacement

    Science.gov (United States)

    Muthusamy, K.; Budiea, A. M. A.; Zaidan, A. L. F.; Rasid, M. H.; Hazimmah, D. S.

    2017-11-01

    Environmental degradation due to excessive sand mining dumping at certain places and disposal of foamed concrete block waste from lightweight concrete producing industry are issues that should be resolved for a better and cleaner environment of the community. Thus, the main intention of this study is to investigate the potential of foamed concrete block waste as partial sand replacement in concrete production. The foamed concrete waste (FCW) used in this research that were supplied by a local lightweight concrete producing industry. The workability and compressive strength of concrete containing various percentage of foamed concrete waste as partial sand replacement has been investigated. Prior to the use, the foamed concrete waste were crushed to produce finer particles. Six concrete mixes containing various content of crushed foamed concrete waste that are 0%, 10%, 20%, 30%, 40% and 50% were used in this experimental work. Then the prepared specimens were placed in water curing until the testing age. Compressive strength test and flexural strength tests were conducted at 7, 14 and 28 days. The result shows that integration of crushed foamed concrete waste as partial sand replacement in concrete reduces the mix workability. It is interesting to note that both compressive strength and flexural strength of concrete improves when 30% crushed foamed concrete waste is added as partial sand replacement.

  8. Understanding the conductive channel evolution in Na:WO3-x-based planar devices

    Science.gov (United States)

    Shang, Dashan; Li, Peining; Wang, Tao; Carria, Egidio; Sun, Jirong; Shen, Baogen; Taubner, Thomas; Valov, Ilia; Waser, Rainer; Wuttig, Matthias

    2015-03-01

    An ion migration process in a solid electrolyte is important for ion-based functional devices, such as fuel cells, batteries, electrochromics, gas sensors, and resistive switching systems. In this study, a planar sandwich structure is prepared by depositing tungsten oxide (WO3-x) films on a soda-lime glass substrate, from which Na+ diffuses into the WO3-x films during the deposition. The entire process of Na+ migration driven by an alternating electric field is visualized in the Na-doped WO3-x films in the form of conductive channel by in situ optical imaging combined with infrared spectroscopy and near-field imaging techniques. A reversible change of geometry between a parabolic and a bar channel is observed with the resistance change of the devices. The peculiar channel evolution is interpreted by a thermal-stress-induced mechanical deformation of the films and an asymmetric Na+ mobility between the parabolic and the bar channels. These results exemplify a typical ion migration process driven by an alternating electric field in a solid electrolyte with a low ion mobility and are expected to be beneficial to improve the controllability of the ion migration in ion-based functional devices, such as resistive switching devices.An ion migration process in a solid electrolyte is important for ion-based functional devices, such as fuel cells, batteries, electrochromics, gas sensors, and resistive switching systems. In this study, a planar sandwich structure is prepared by depositing tungsten oxide (WO3-x) films on a soda-lime glass substrate, from which Na+ diffuses into the WO3-x films during the deposition. The entire process of Na+ migration driven by an alternating electric field is visualized in the Na-doped WO3-x films in the form of conductive channel by in situ optical imaging combined with infrared spectroscopy and near-field imaging techniques. A reversible change of geometry between a parabolic and a bar channel is observed with the resistance change of the

  9. Recycled construction and demolition concrete waste as aggregate for structural concrete

    Directory of Open Access Journals (Sweden)

    Ashraf M. Wagih

    2013-12-01

    Full Text Available In major Egyptian cities there is a surge in construction and demolition waste (CDW quantities causing an adverse effect on the environment. The use of such waste as recycled aggregate in concrete can be useful for both environmental and economical aspects in the construction industry. This study discusses the possibility to replace natural coarse aggregate (NA with recycled concrete aggregate (RCA in structural concrete. An investigation into the properties of RCA is made using crushing and grading of concrete rubble collected from different demolition sites and landfill locations around Cairo. Aggregates used in the study were: natural sand, dolomite and crushed concretes obtained from different sources. A total of 50 concrete mixes forming eight groups were cast. Groups were designed to study the effect of recycled coarse aggregates quality/content, cement dosage, use of superplasticizer and silica fume. Tests were carried out for: compressive strength, splitting strength and elastic modulus. The results showed that the concrete rubble could be transformed into useful recycled aggregate and used in concrete production with properties suitable for most structural concrete applications in Egypt. A significant reduction in the properties of recycled aggregate concrete (RAC made of 100% RCA was seen when compared to natural aggregate concrete (NAC, while the properties of RAC made of a blend of 75% NA and 25% RCA showed no significant change in concrete properties.

  10. Synthesis and Characterization of Graphene Oxide-Modified Bi2WO6 and Its Use as Photocatalyst

    Directory of Open Access Journals (Sweden)

    Xiaoyue Hu

    2016-01-01

    Full Text Available A Bi2WO6 photocatalyst modified with graphene was synthesized in a two-step template-free hydrothermal process. The prepared samples were characterized to explore their properties. The photocatalytic activities of the prepared samples were investigated by degrading dye model, Rhodamine B (RhB, under visible light irradiation. This showed that the modified Bi2WO6 photocatalyst with 1.2 wt% of graphene greatly improved photocatalytic activity during the degradation of dye pollutants, compared to pure Bi2WO6. The enhancement can be interpreted as the integrated effects of ultrahigh charge carriers’ mobility and high adsorption of RhB on graphene. Additionally, effects including catalysts dosage amount, pH of RhB solution, and temperature of reactor on the photocatalytically degrading RhB were also studied and discussed.

  11. Special protective concretes

    International Nuclear Information System (INIS)

    Bouniol, P.

    2001-01-01

    Concrete is the most convenient material when large-scale radiation protection is needed. Thus, special concretes for nuclear purposes are used in various facilities like reactors, reprocessing centers, storage sites, accelerators, hospitals with nuclear medicine equipment, food ionization centers etc.. The recent advances made in civil engineering for the improvement of concrete durability and compactness are for a large part transposable to protection concretes. This article presents the basic knowledge about protection concretes with the associated typological and technological aspects. A large part is devoted to the intrinsic properties of concretes and to their behaviour in irradiation and temperature conditions: 1 - definition and field of application of special protective concretes; 2 - evolution of concepts and technologies (durability of structures, techniques of formulation, new additives, market evolution); 3 - design of protective structures (preliminary study, radiation characteristics, thermal constraints, damping and dimensioning, mechanical criteria); 4 - formulation of special concretes (general principles, granulates, hydraulic binders, pulverulent additives, water/cement ratio, reference composition of some special concretes); 5 - properties of special concretes (damping and thermo-mechanical properties); 6 - induced-irradiation and temperature phenomena (activation, radiolysis, mineralogical transformations, drying, shrinking, creep, corrosion of reinforcement). (J.S.)

  12. Facile one-step hydrothermal synthesis and luminescence properties of Eu{sup 3+}-doped NaGd(WO{sub 4}){sub 2} nanophosphors

    Energy Technology Data Exchange (ETDEWEB)

    Jiang, Zehan; Cai, Peiqing; Chen, Cuili; Pu, Xipeng; Kim, Sun Il, E-mail: sikim@pknu.ac.kr; Jin Seo, Hyo, E-mail: hjseo@pknu.ac.kr

    2017-06-01

    Eu{sup 3+}-doped NaGd(WO{sub 4}){sub 2} nanophosphors were synthesized via a facile one-step hydrothermal method without any surfactants or a further heat treatment. X-ray powder diffraction (XRD), scanning electron microscope (SEM), fourier transform infrared spectroscopy (FT-IR), the photoluminescence (PL) excitation and emission spectra, and decay curves were used to characterize NaGd(WO{sub 4}){sub 2}:Eu{sup 3+} phosphors. The results show that the Eu{sup 3+}-concentration has little influence on the structure and morphology of the as-synthesized samples. However, pH value plays a vital role on the structure and morphology of NaGd(WO{sub 4}){sub 2}. The well-crystallized sheet-like NaGd(WO{sub 4}){sub 2} phosphors can be obtained only at pH = 5–7. On the basis of the time-dependent synthesis, a possible growth mechanism of sheet-like architectures is proposed. The luminescence properties of NaGd{sub 1-x}Eu{sub x}(WO{sub 4}){sub 2} (0 ≤ x ≤ 1) are investigated. It is found that the charge transfer band of Eu{sup 3+} shifts to lower energy and broadens with increasing the Eu{sup 3+}-concentration. - Highlights: • NaGd(WO{sub 4}){sub 2}:Eu{sup 3+} nanosheets were synthesized by facile one-step hydrothermal method. • Luminescence properties of NaGd(WO{sub 4}){sub 2}:Eu{sup 3+} phosphor were firstly reported. • The CT band of Eu{sup 3+} depends strongly on Eu{sup 3+}-concentrations.

  13. Luminescence and energy transfer mechanisms in CaWO{sub 4} single crystals

    Energy Technology Data Exchange (ETDEWEB)

    Spassky, D., E-mail: deris2002@mail.ru [Skobeltsyn Institute of Nuclear Physics, M.V. Lomonosov Moscow State University, Vorob' evy Gory, 119991 Moscow (Russian Federation); Mikhailin, V. [Skobeltsyn Institute of Nuclear Physics, M.V. Lomonosov Moscow State University, Vorob' evy Gory, 119991 Moscow (Russian Federation); Nazarov, M. [School of Materials and Mineral Resources Engineering, Universiti Sains Malaysia, 14300 Nibong Tebal, Penang (Malaysia); Institute of Applied Physics, Academiei Street 5, Chisinau MD-2028 (Moldova, Republic of); Ahmad-Fauzi, M.N. [School of Materials and Mineral Resources Engineering, Universiti Sains Malaysia, 14300 Nibong Tebal, Penang (Malaysia); Zhbanov, A. [Department of Medical System Engineering, Gwangju Institute of Science and Technology, 1 Oryong-dong, Buk-gu, Gwangju 500-712 (Korea, Republic of)

    2012-10-15

    The processes of the excitation energy transfer to the emission centers have been investigated for calcium tungstate crystals taking into account features of the electronic structure of valence band and conduction band. The calculations of the electronic structure of host lattice CaWO{sub 4} were performed in the framework of density functional theory. The underestimation of the bandgap value in the calculations has been corrected according to the experimental data. Luminescence of two samples grown using Czochralski (cz) and hydrothermal (ht) techniques were studied. Intrinsic emission band related to excitons, self-trapped on WO{sub 4} complexes has been observed for the both samples while the additional low-energy emission band related to the defects of crystal structure has been observed only for (ht) sample indicating the enhanced concentration of the defects in the sample. It was shown that the features of the conduction band electronic structure are reproduced in the excitation spectrum of intrinsic luminescence only for the (ht) sample while for (cz) sample the correlation is absent. The enhanced role of the competitive channels in the process of excitation energy transfer to intrinsic emission centers in (ht) sample is responsible for the observed difference. - Highlights: Black-Right-Pointing-Pointer The band structure of CaWO{sub 4} was calculated in the framework of DFT LAPW method. Black-Right-Pointing-Pointer Calculation results were validated via joint analysis with experimental data. Black-Right-Pointing-Pointer The bandgap E{sub g} of CaWO{sub 4} was determined as 4.90{+-}0.15 eV. Black-Right-Pointing-Pointer The correlation between the band structure and excitation spectrum is demonstrated. Black-Right-Pointing-Pointer Influence of competitive relaxation channel on energy transfer to STE is shown.

  14. Ethanol vapour sensing properties of screen printed WO3 thick films

    Indian Academy of Sciences (India)

    TECS

    trations. The WO3 thick films exhibit excellent ethanol vapour sensing properties with a maximum sensitivity ... methanol, acetone, isopropanol and acetic acid, have been reported .... maximum sensitivity was obtained at an operating tem-.

  15. Dioxin sensing which uses fluorescent cyclodextrin; Keikosei shikurodekisutorin wo mochiita daiokishin senshingu

    Energy Technology Data Exchange (ETDEWEB)

    Hamada, F. [Akita Univ., Akita (Japan)

    2000-05-01

    Environmental hormones are called pluricausal endocrine disrupting chemical substances (endocrine disrupters) that are deemed to disrupt effects of vital hormones and give influence to homeostasis of in vivo environment. Today, 70,000 to 80,000 kinds of chemical substances are used in the world, and about 70 kinds among them are suspected of being environmental hormones. The present authors have clarified that a host with fluorescent residue chemically bonded to cyclodextrin responses at a high sensitivity to bile acids having a steroid skeleton. In this paper, dioxin sensing that uses fluorescent cyclodextrin is described. Florescent sensing of a dansyl group or anthranyl ground modified cyclodextrin having somewhat different molecular sizes; and sensing of hetero-2 substituted-dansyl-tosyl, modified {beta}-, cyclodextrin are examined. (NEDO)

  16. Self-Compacting Concrete

    OpenAIRE

    Okamura, Hajime; Ouchi, Masahiro

    2003-01-01

    Self-compacting concrete was first developed in 1988 to achieve durable concrete structures. Since then, various investigations have been carried out and this type of concrete has been used in practical structures in Japan, mainly by large construction companies. Investigations for establishing a rational mix-design method and self-compactability testing methods have been carried out from the viewpoint of making self-compacting concrete a standard concrete.

  17. A review on the suitability of rubberized concrete for concrete bridge decks

    Science.gov (United States)

    Syamir Senin, Mohamad; Shahidan, Shahiron; Radziah Abdullah, Siti; Anting Guntor, Nickholas; Syazani Leman, Alif

    2017-11-01

    Road authorities manage a large population of ageing bridges, a substantial number of which fail to meet the current requirements either due to deterioration and other structural deficiencies or as a result of the escalating demands imposed by increased traffic. This problem is related to the dynamic load from vehicles. This problem can be solved by producing a type of concrete that can reduce the amplitude of oscillation or vibration such as rubberized concrete. Green construction has been a very important aspect in concrete production field in the last decade. One of the most problematic waste materials is scrap tires. The use of scrap tires in civil engineering is increasing by producing rubberized concrete. Rubberized concrete is a type of concrete that is mixed with rubber. The purpose of this review is to justify the suitability of rubberized concrete for concrete bridge decks. Several parameters named physical, chemical and mechanical properties were measured to ensure the suitability of rubberized concrete for concrete bridge decks. Rubberized concrete has similar workability to normal concrete. The rubber reduced the density and compressive strength of the concrete while increased the flexural strength, water absorption and damping ratio. The used of rubber in concrete beyond 20% is not recommended due to decreasing in compressive strength. Rubberized concrete recommended to be used in circumstances where vibration damping was required such as in bridge construction as shock-wave absorber.

  18. Electrosprayed heterojunction WO{sub 3}/BiVO{sub 4} films with nanotextured pillar structure for enhanced photoelectrochemical water splitting

    Energy Technology Data Exchange (ETDEWEB)

    Mali, Mukund G.; Yoon, Hyun; Yoon, Sam S., E-mail: skyoon@korea.ac.kr [School of Mechanical Engineering, Korea University, Seoul 136-713 (Korea, Republic of); Kim, Min-woo [School of Mechanical Engineering, Korea University, Seoul 136-713 (Korea, Republic of); Green School, Korea University, Seoul 136-713 (Korea, Republic of); Swihart, Mark T. [Department of Chemistry and Biological Engineering, University at Buffalo (SUNY), Buffalo, New York 14260 (United States); Al-Deyab, Salem S. [Department of Chemistry, College of Science, King Saud University, Riyadh 11451 (Saudi Arabia)

    2015-04-13

    We demonstrate that the addition of a tungsten oxide (WO{sub 3}) layer beneath a bismuth vanadate (BiVO{sub 4}) photocatalyst layer with a nanotextured pillar morphology significantly increases the photocurrent density in photoelectrochemical water splitting. The WO{sub 3}-BiVO{sub 4} bilayer films produced a photocurrent of up to 3.3 mA/cm{sup 2} under illumination at 100 mW/cm{sup 2} (AM1.5 spectrum). The bilayer film was characterized by scanning electron microscopy, X-ray diffraction, and photoelectrochemical methods, which confirmed the superiority of the bilayer film in terms of its morphology and charge separation and transport ability. Both WO{sub 3} and BiVO{sub 4} were deposited by electrostatic spraying under open-air conditions, which resulted in nanotextured pillars of BiVO{sub 4} atop a smooth WO{sub 3} film. The optimal coating conditions are also reported.

  19. Gasochromic performance of WO3-nanorod thin films fabricated with an ArF excimer laser

    International Nuclear Information System (INIS)

    Yaacob, M. H.; Ou, J. Z.; Wlodarski, W.; Kim, C. S.; Lee, J. Y.; Kim, Y. H.; Oh, C. M.; Dhakal, K. P.; Kim, J. Y.; Kang, J. H.

    2012-01-01

    Thin films with tungsten trioxide (WO 3 ) nanorods were fabricated by using an ArF pulsed laser deposition system. Because the ArF excimer laser operates at a very short wavelength of 193 nm, short enough to expect strong absorption of the photons in the semiconductor oxide targets, and because the clusters incoming to the substrates have high momentum, we could build thin films with good surface morphology. Highly homogeneous arrays of nanorods with sizes mostly in the range of 30 - 40 nm were observed. The absorbance response towards hydrogen (H 2 ) gas was investigated for a WO 3 film coated with 25-A-thick palladium (Pd). The Pd/WO 3 -nanorod thin films exhibited excellent gasochromic response when measured in the visible-NIR range (400 - 1000 nm). As low as 0.06% H 2 concentration was clearly sensed. A significant reversible absorbance change and fast recovery ( 2 at different concentrations.

  20. A P25/(NH4)xWO3 hybrid photocatalyst with broad spectrum photocatalytic properties under UV, visible, and near-infrared irradiation.

    Science.gov (United States)

    Yang, Linfen; Liu, Bin; Liu, Tongyao; Ma, Xinlong; Li, Hao; Yin, Shu; Sato, Tsugio; Wang, Yuhua

    2017-04-03

    In this study, a series of hybrid nanostructured photocatalysts P25/(NH 4 ) x WO 3 nanocomposites with the average crystallite size of P25 and (NH 4 ) x WO 3 of the sample was calculated to be about 30 nm and 130 nm, were successfully synthesized via a simple one-step hydrothermal method. The as-obtained samples was characterized by transmission electron microscopy (TEM), which implies that the P25/(NH 4 ) x WO 3 nanocomposites are fabricated with favourable nanosizd interfacial. The XPS results confirmed that the obtained sample consists of mixed chemical valences of W 5+ and W 6+ , the low-valance W 5+ sites could be the origin of NIR absorption. As revealed by optical absorption results, P25/(NH 4 ) x WO 3 nanocomposites possess high optical absorption in the whole solar spectrum of 200-2500 nm. Benefiting from this unique photo-absorption property and the synergistic effect of P25 and (NH 4 ) x WO 3 , broad spectrum response photocatalytic activities covering UV, visible and near infrared regions on degradation of Rhodamine B have been realized by P25/(NH 4 ) x WO 3 nanocomposites. Meanwhile, the stability of photocatalysts was examined by the XRD and XPS of the photocatalysts after the reaction. The results show that P25/(NH 4 ) x WO 3 photocatalysts has a brilliant application prospect in the energy utilization to solve deteriorating environmental issues.

  1. Immobilized WO3 nanoparticles on graphene oxide as a photo-induced antibacterial agent against UV-resistant Bacillus pumilus

    Science.gov (United States)

    Hosseini, Farshad; Rasuli, Reza; Jafarian, Vahab

    2018-04-01

    We present the antibacterial and photo-catalytic activity of immobilized WO3 nanoparticles on graphene oxide sheets. WO3 nanoparticles were immobilized on graphene oxide using the arc discharge method in arc currents of 5, 20, 40 and 60 A. Tauc plots of the UV-visible spectra show that the band gap of the prepared samples decreases (to ~2.7 eV) with respect to the WO3 nanoparticles. Photo-catalytic activity was examined by the degradation of rhodamine B under ultra-violet irradiation and the results show that the photo-catalytic activity of WO3 nanoparticles is increased by immobilizing them on graphene oxide sheets. In addition, the photo-degradation yield of the samples prepared by the 5 A arc current is 84% in 120 min, which is more than that of the other samples. The antibacterial activity of the prepared samples was studied against Bacillus pumilus (B. pumilus) bacteria, showing high resistance to ultra-violet exposure. Our results show that the bare and immobilized WO3 nanoparticles become more active under UV irradiation and their antibacterial properties are comparable with Ag nanoparticles. Besides this, the results show that although the photo-catalytic activity of the post-annealed samples at 500 °C is less than the as-prepared samples, it is, however, more active against B. pumilus bacteria under UV irradiation.

  2. In situ loading of Ag_2WO_4 on ultrathin g-C_3N_4 nanosheets with highly enhanced photocatalytic performance

    International Nuclear Information System (INIS)

    Li, Yunfeng; Jin, Renxi; Fang, Xu; Yang, Yang; Yang, Man; Liu, Xianchun; Xing, Yan; Song, Shuyan

    2016-01-01

    Graphical abstract: Ultrathin g-C_3N_4 nanosheets (g-C_3N_4−NS) with improved electron transport ability and large number of active sites are employed instead of bulk g-C_3N_4 to prepare the Ag_2WO_4/g-C_3N_4−NS heterostructured photocatalysts, which exhibit remarkable photocatalytic activity for wastewater treatment. - Highlights: • Ag2WO4/g-C3N4-NS photocatalysts were obtained by a deposition-precipitation method. • Ag2WO4/g-C3N4-NS possess large surface areas and increased lifetime of charges. • Ag2WO4/g-C3N4-NS exhibit enhanced activity on degradation of RhB and MO. • The photocatalytic mechanism of the Ag2WO4/g-C3N4-NS system were investigated. - Abstract: The g-C_3N_4 nanosheets (g-C_3N_4−NS) exhibit more excellent property than common bulk g-C_3N_4 (g-C_3N_4-B) due to their large surface areas, improved electron transport ability and well dispersion in water. In this work, ultrathin g-C_3N_4−NS with a thickness of about 2.7 nm have been synthesized by a simple thermal exfoliation of bulk g-C_3N_4, and then Ag_2WO_4 nanoparticles are in situ loaded on their surface to construct the Ag_2WO_4/g-C_3N_4−NS heterostructured photocatalysts. Due to their unique physicochemical properties, the as-prepared heterostructures possess a fast interfacial charge transfer and increased lifetime of photo-excited charge carriers, and exhibit much higher photocatalytic activity. Under visible light irradiation, the optimum photocatalytic activity of Ag_2WO_4/g-C_3N_4−NS composites is almost 53.6 and 26.5 times higher than that of pure g-C_3N_4-B and Ag_2WO_4/g-C_3N_4-B heterostructures towards the degradation of rhodamine B, respectively, and is almost 30.6 and 9.8 times higher towards the degradation of methyl orange, respectively. In addition, the natural sunlight photocatalytic activities of the as-prepared samples are also investigated.

  3. Ease synthesis of mesoporous WO3-TiO2 nanocomposites with enhanced photocatalytic performance for photodegradation of herbicide imazapyr under visible light and UV illumination.

    Science.gov (United States)

    Ismail, Adel A; Abdelfattah, Ibrahim; Helal, Ahmed; Al-Sayari, S A; Robben, L; Bahnemann, D W

    2016-04-15

    Herein, we report the ease synthesis of mesoporous WO3-TiO2 nanocomposites at different WO3 contents (0-5wt%) together with their photocatalytic performance for the degradation of the imazapyr herbicide under visible light and UV illumination. XRD and Raman spectra indicated that the highly crystalline anatase TiO2 phase and monoclinic and triclinic of WO3 were formed. The mesoporous TiO2 exhibits large pore volumes of 0.267cm(3)g-1 and high surface areas of 180m(2)g(-1) but they become reduced to 0.221cm(3)g(-1) and 113m(2)g(-1), respectively upon WO3 incorporation, with tunable mesopore diameter in the range of 5-6.5nm. TEM images show WO3-TiO2 nanocomposites are quite uniform with 10-15nm of TiO2 and 5-10nm of WO3 sizes. Under UV illumination, the overall photocatalytic efficiency of the 3% WO3-TiO2 nanocomposite is 3.5 and 6.6 times higher than that of mesoporous TiO2 and commercial UV-100 photocatalyst, respectively. The 3% WO3-TiO2 nanocomposite is considered to be the optimum photocatalyst which is able to degrade completely (100% conversion) of imazapyr herbicide along 120min with high photonic efficiency ∼8%. While under visible light illumination, the 0.5% WO3-TiO2 nanocomposite is the optimum photocatalyst which achieves 46% photocatalytic efficiency. Copyright © 2015 Elsevier B.V. All rights reserved.

  4. Crystal structures of the double perovskites Ba2Sr1-x Ca x WO6

    International Nuclear Information System (INIS)

    Fu, W.T.; Akerboom, S.; IJdo, D.J.W.

    2007-01-01

    Structures of the double perovskites Ba 2 Sr 1- x Ca x WO 6 have been studied by the profile analysis of X-ray diffraction data. The end members, Ba 2 SrWO 6 and Ba 2 CaWO 6 , have the space group I2/m (tilt system a 0 b - b - ) and Fm3-barm (tilt system a 0 a 0 a 0 ), respectively. By increasing the Ca concentration, the monoclinic structure transforms to the cubic one via the rhombohedral R3-bar phase (tilt system a - a - a - ) instead of the tetragonal I4/m phase (tilt system a 0 a 0 c - ). This observation supports the idea that the rhombohedral structure is favoured by increasing the covalency of the octahedral cations in Ba 2 MM'O 6 -type double perovskites, and disagrees with a recent proposal that the formation of the π-bonding, e.g., d 0 -ion, determines the tetragonal symmetry in preference to the rhombohedral one. - Graphical abstract: Enlarged sections showing the evolution of the basic (222) and (400) reflections in Ba 2 Sr 1- x Ca x WO 6 . Tick marks below are the positions of Bragg's reflections calculated using the space groups I2/m (x=0), R3-bar (x=0.25, 0.5 and 0.75) and Fm3-barm (x=1), respectively

  5. Investigation of W/O microemulsion droplets by contrast variation ...

    Indian Academy of Sciences (India)

    various molar ratios (µ) of water to AOT and temperatures on water-in-oil (W/O) mi- croemulsions dispersed in n-heptane, ... tures composed of surfactant, water, and oil have attracted much interest since they form thermodynamically stable phases .... filter into dust-free sample cells. The cylindrical sample cells are made of ...

  6. Crystal structure and phase transition in (NH4)3WO2F5: from dynamic to static orientational disorder.

    Science.gov (United States)

    Udovenko, Anatoly; Laptash, Natalia

    2015-08-01

    Single crystals of tungsten double salt (NH4)3WO2F5 = (NH4)3[WO2F4]F have been synthesized by solid-state reaction or from fluoride solution and its crystal structures at 296 and 193 K were determined by X-ray diffraction. At room temperature, the crystal structure of the compound is dynamically disordered with the ligand atoms statistically distributed on two positions (6e and 24m) of the Pm3m unit cell [a = 6.0298 (1) Å], and the tungsten atom dynamically disordered on 12 orientations forming a spatial cuboctahedron [W12] that enables the real geometry of cis-WO2F4 octahedron to be determined with two short W-O distances. On cooling, the compound undergoes a first-order phase transition with the symmetry change Pm3m → Pa3 and a doubling of the unit-cell parameter [a = 11.9635 (7) Å]. The ligand F(O) atoms statistically occupy two general 24d sites and form W1X6 and W2X6 octahedra, in which the O and F atoms are not crystallographically different that means a static orientational disorder of (NH4)3WO2F5.

  7. Polymorphism and properties of Bi{sub 2}WO{sub 6} doped with pentavalent antimony

    Energy Technology Data Exchange (ETDEWEB)

    Kharitonova, E.P.; Belov, D.A. [M.V. Lomonosov Moscow State University, Leninskie Gory, 119991 Moscow (Russian Federation); Gagor, A.B.; Pietraszko, A.P. [W. Trzebiatowski Institute of Low Temperature and Structure Research, Polish Academy of Sciences, Okólna 2, 50-950 Wrocław (Poland); Alekseeva, O.A. [Shubnikov Institute of Crystallography, Russian Academy of Sciences, Leninsky pr. 59, 119333 Moscow (Russian Federation); Voronkova, V.I., E-mail: voronk@polly.phys.msu.ru [M.V. Lomonosov Moscow State University, Leninskie Gory, 119991 Moscow (Russian Federation)

    2014-04-05

    Highlights: • The limit of Bi{sub 2}W{sub 1−x}Sb{sub x}O{sub 6−y} solid solutions is at x = 0.05. • Bi{sub 2}W{sub 1−x}Sb{sub x}O{sub 6−y} does not fully transform into high-temperature monoclinic phase. • Sb{sup 5+} has a weak effect on the temperatures of the ferroelectric transitions. • γ→γ{sup ‴} transition near 650 °C was observed as strong permittivity peak at 0.01–8 Hz. • The conductivity of Bi{sub 2}W{sub 0.96}Sb{sub 0.04}O{sub 6−y} at 800 °C reaches 0.02 S/cm. -- Abstract: Antimony-containing solid solutions isostructural with bismuth tungstate, Bi{sub 2}WO{sub 6}, have been prepared in air as polycrystalline samples by solid-state reactions and as single crystals by unseeded flux growth. The antimony in the solid solutions is in a pentavalent state and substitutes for tungsten in the structure of Bi{sub 2}WO{sub 6}. The Bi{sub 2}W{sub 1−x}Sb{sub x}O{sub 6−y} solid solutions have been shown to exist in the composition range 0 ⩽ x ⩽ 0.05. We have examined the effect of Sb{sup 5+} doping on the polymorphism and properties of Bi{sub 2}WO{sub 6}. In contrast to undoped Bi{sub 2}WO{sub 6}, antimony-substituted bismuth tungstate does not completely transform into its high-temperature, monoclinic phase at 960 °C and remains two-phase up to temperatures approaching its melting point. Antimony substitution for tungsten has a weak effect on the temperatures of the ferroelectric phase transitions. Heterovalent substitution of Sb{sup 5+} for W{sup 6+} is accompanied by the formation of extra oxygen vacancies and an increase in the electrical conductivity of the solid solutions by one to two orders of magnitude relative to undoped Bi{sub 2}WO{sub 6}.

  8. Determination and modeling for the solubility of Na_2WO_4·2H_2O and Na_2MoO_4·2H_2O in the (Na"+ + MoO_4"2"− + WO_4"2"− + SO_4"2"− + H_2O) system

    International Nuclear Information System (INIS)

    Ning, Pengge; Xu, Weifeng; Cao, Hongbin; Xu, Hongbin

    2016-01-01

    Highlights: • The solubility of Na_2MoO_4·2H_2O and Na_2WO_4·2H_2O in Na_2MoO_4–Na_2WO_4–Na_2SO_4–H_2O were performed. • The solubility of sodium tungstate dihydrate in Na_2WO_4–Na_2SO_4–H_2O was determined. • The new model was established via regressing the published and the determined data. • The Pitzer parameter and the solubility product constant of the salt in solution were calculated. • The model was used to estimate the solubility of the sodium molybdate and sodium tungstate. - Abstract: The solubility of sodium tungstate dihydrate and sodium molybdate dihydrate in the (Na_2MoO_4 + Na_2WO_4 + Na_2SO_4 + H_2O) system was studied using experimental and calculated methods. The osmotic coefficient of sodium tungstate was fitted to calculate the thermodynamics parameters of (Na_2WO_4 + H_2O) system. The solubility of sodium tungstate dihydrate was determined using the dynamic method in Na_2WO_4–Na_2SO_4–H_2O to establish the new model which can provide an estimate the solubility of sodium tungstate dihydrate in various conditions, combined with the data published, the solubility of sodium tungstate dihydrate and the sodium molybdate dihydrate in quaternary system of (Na_2MoO_4 + Na_2WO_4 + Na_2SO_4 + H_2O) was estimated using the parameters of the two ternary systems of (Na_2WO_4 + Na_2SO_4 + H_2O) and (Na_2MoO_4 + Na_2SO_4 + H_2O). The results show that the AARD is always small and the calculated value is basically consistent with the experimental values for the system studied.

  9. Highly efficient visible-light-induced photocatalytic activity of Bi{sub 2}WO{sub 6}/BiVO{sub 4} heterojunction photocatalysts

    Energy Technology Data Exchange (ETDEWEB)

    Chaiwichian, Saranyoo [Department of Physics and Materials Science, Faculty of Science, Chiang Mai University, Chiang Mai50200 (Thailand); Inceesungvorn, Burapat [Department of Chemistry, Faculty of Science, Chiang Mai University, Chiang Mai 50200 (Thailand); Wetchakun, Khatcharin [Program of Physics, Faculty of Science, Ubon Ratchathani Rajabhat University, Ubon Ratchathani 34000 (Thailand); Phanichphant, Sukon [Materials Science Research Center, Faculty of Science, Chiang Mai University, Chiang Mai 50200 (Thailand); Kangwansupamonkon, Wiyong [National Nanotechnology Center, Thailand Science Park, Phahonyotin Road, Klong 1, Klong Luang, Phathumthani 12120 (Thailand); Wetchakun, Natda, E-mail: natda_we@yahoo.com [Department of Physics and Materials Science, Faculty of Science, Chiang Mai University, Chiang Mai50200 (Thailand)

    2014-06-01

    Highlights: • Bi{sub 2}WO{sub 6}/BiVO{sub 4} heterojunction photocatalysts were obtained using hydrothermal method. • Physicochemical properties played a significant role on photocatalytic efficiency. • Bi{sub 2}WO{sub 6}/BiVO{sub 4} heterogeneous structures were greatly enhanced for degradation of MB. • A tentative mechanism of charge transfer process in MB degradation was proposed. - Abstract: The Bi{sub 2}WO{sub 6}/BiVO{sub 4} heterojunction photocatalysts were synthesized by hydrothermal method. Physical properties of the heterojunction photocatalyst samples were studied by X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM) techniques. The XRD results indicated that BiVO{sub 4} retain monoclinic and tetragonal structures, while Bi{sub 2}WO{sub 6} presented as orthorhombic structure. The Brunauer, Emmett and Teller (BET) adsorption–desorption of nitrogen gas for specific surface area determination at the temperature of liquid nitrogen was performed on all samples. UV–vis diffuse reflectance spectra (UV–vis DRS) were used to identify the absorption range and band gap energy of the heterojunction photocatalysts. The photocatalytic performance of Bi{sub 2}WO{sub 6}/BiVO{sub 4} heterojunction photocatalysts was studied via the photodegradation of methylene blue (MB) under visible light irradiation. The results indicated that the heterojunction photocatalyst at 0.5:0.5 mole ratio of Bi{sub 2}WO{sub 6}:BiVO{sub 4} shows the highest photocatalytic activity.

  10. PEGylated (NH4)xWO3 nanorods as efficient and stable multifunctional nanoagents for simultaneous CT imaging and photothermal therapy of tumor.

    Science.gov (United States)

    Macharia, Daniel K; Tian, Qiyun; Chen, Liang; Sun, Yingqi; Yu, Nuo; He, Chuanglong; Wang, Han; Chen, Zhigang

    2017-09-01

    The simultaneous imaging and photothermal therapy of tumors have attracted much attention, and a prerequisite is to obtain multifunctional nanomaterials. Ideally, one kind of nanoparticles with single component can be used as both imaging agent and photothermal agent. Herein, we have developed the PEGylated (NH 4 ) x WO 3 (denoted as (NH 4 ) x WO 3 -PEG) nanorods as multifunctional nanoparticles with single semiconductor component. (NH 4 ) x WO 3 -PEG nanorods with about 30nm diameter and length of several hundred nanometers have been obtained through a solvothermal synthesis-PEGylation two-step route. Under the irradiation of 980-nm laser with intensity of 0.72Wcm -2 , aqueous dispersion of (NH 4 ) x WO 3 -PEG nanorods (0.67-5.44mmol/L) displays high elevation (17.6-34.5°C) of temperature in 400s, accompanied by an excellent long-term photothermal stability. Furthermore, (NH 4 ) x WO 3 -PEG nanorods exhibit as high as 6 times X-ray attenuation ability compared to that of the clinically used iodine-based X-ray computed tomography (CT) contrast agent (Iopromide). More importantly, after PBS solution of (NH 4 ) x WO 3 -PEG nanorods is injected into the tumor of mice, the tumor can be effectively detected by CT imaging. Moreover, cancer cells in vivo can be further destroyed by the photothermal effects of (NH 4 ) x WO 3 -PEG nanorods, under the irradiation of 980-nm laser with the safe intensity of 0.72Wcm -2 for 10min. Therefore, (NH 4 ) x WO 3 -PEG nanorods can be used as a new kind of stable and efficient multifunctional nanoagent with single component for simultaneous CT imaging and photothermal therapy of tumor. Copyright © 2017. Published by Elsevier B.V.

  11. Layered MoSe2/Bi2WO6 composite with P-N heterojunctions as a promising visible-light induced photocatalyst

    Science.gov (United States)

    Xie, Taiping; Liu, Yue; Wang, Haiqiang; Wu, Zhongbiao

    2018-06-01

    In this paper, layered MoSe2/Bi2WO6 composites were fabricated by a simple bath sonication method for photocatalytic applications. Their photocatalytic performances were then investigated via the photocatalytic oxidation of gaseous toluene under visible-light irradiation. As a result, 1.5%-MoSe2/Bi2WO6 catalyst showed the highest activity with a degradation rate of nearly 80% during three-hour visible-light irradiation. The k value determined of 1.5%-MoSe2/Bi2WO6 was approximately 6 times higher than that of pure Bi2WO6 and 7 times higher compared with pure MoSe2. After a series of characterizations, it was concluded that the p-n heterojunctions of MoSe2/Bi2WO6 composites with strong interlayer interactions could effectively prolong the life time of photoinduced electron-hole pairs. And both the contents of surface superoxide and hydroxyl radicals were thereby increased, benefitting the photocatalytic process. Furthermore, the hydroxyl radicals and holes were found to be the major active species. This work provided a way to design photocatalyst with enhanced visible-light driven photoactivity toward indoor air pollutants purification.

  12. Fractal approach to surface roughness of TiO{sub 2}/WO{sub 3} coatings formed by plasma electrolytic oxidation process

    Energy Technology Data Exchange (ETDEWEB)

    Rožić, L.J., E-mail: ljrozic@nanosys.ihtmbg.ac.rs [University of Belgrade, IChTM-Department of Catalysis and Chemical Engineering, Njegoševa 12, Belgrade (Serbia); Petrović, S.; Radić, N. [University of Belgrade, IChTM-Department of Catalysis and Chemical Engineering, Njegoševa 12, Belgrade (Serbia); Stojadinović, S. [University of Belgrade, Faculty of Physics, Studentski trg 12-16, Belgrade (Serbia); Vasilić, R. [Faculty of Environmental Governance and Corporate Responsibility, Educons University, Vojvode Putnika 87, Sremska Kamenica (Serbia); Stefanov, P. [Institute of General and Inorganic Chemistry, Bulgarian Academy of Sciences, Sofia 1113 (Bulgaria); Grbić, B. [University of Belgrade, IChTM-Department of Catalysis and Chemical Engineering, Njegoševa 12, Belgrade (Serbia)

    2013-07-31

    In this study, we have shown that atomic force microscopy is a powerful technique to study the fractal parameters of TiO{sub 2}/WO{sub 3} coatings prepared by plasma electrolytic oxidation (PEO) process. Since the surface roughness of obtained oxide coatings affects their physical properties, an accurate description of roughness parameters is highly desirable. The surface roughness, described by root mean squared and arithmetic average values, is analyzed considering the scans of a series of atomic force micrographs. The results show that the oxide coatings exhibit lower surface roughness in initial stage of PEO process. Also, the surfaces of TiO{sub 2}/WO{sub 3} coatings exhibit fractal behavior. Positive correlation between the fractal dimension and surface roughness of the surfaces of TiO{sub 2}/WO{sub 3} coatings in initial stage of PEO process was found. - Highlights: • TiO{sub 2}/WO{sub 3} coatings were obtained by plasma electrolytic oxidation. • Oxide coatings exhibit lower surface roughness in initial stage of process. • The surfaces of TiO{sub 2}/WO{sub 3} coatings exhibit fractal behavior.

  13. Photocatalytic reduction of CO{sub 2} into methanol and ethanol over conducting polymers modified Bi{sub 2}WO{sub 6} microspheres under visible light

    Energy Technology Data Exchange (ETDEWEB)

    Dai, Weili, E-mail: wldai81@126.com; Xu, Hai; Yu, Juanjuan; Hu, Xu; Luo, Xubiao, E-mail: luoxubiao@126.com; Tu, Xinman; Yang, Lixia

    2015-11-30

    Graphical abstract: - Highlights: • Conducting polymers modified Bi{sub 2}WO{sub 6} HHMS (CP/Bi{sub 2}WO{sub 6}) was successfully synthesized. • The introduction of CP decreases the recombination of photogenerated e{sup –}–h{sup +} pairs. • The PTh/Bi{sub 2}WO{sub 6} exhibites good stability and recyclability for CO{sub 2} photoreduction. • The possible photocatalytic mechanism was discussed and proposed. - Abstract: Bi{sub 2}WO{sub 6} hierarchical hollow microspheres (HHMS) modified with different conducting polymers (polyaniline, polypyrrole, and polythiophene) were successfully synthesized by ‘in situ’ deposition oxidative polymerization method, and evaluated as photocatalysts for the photocatalytic reduction of CO{sub 2} with H{sub 2}O to methanol and ethanol. It was found that the introduction of conducting polymers obviously decreased the recombination of photogenerated electron–hole pairs, thus promoting the photocatalytic activity of Bi{sub 2}WO{sub 6}. Among the as-fabricated photocatalysts, polythiophene modified Bi{sub 2}WO{sub 6} (PTh/Bi{sub 2}WO{sub 6}) exhibited the best photoelectronic and photocatalytic performance, due to the narrow band gap and good charge mobility of polythiophene. The results demonstrate that the methanol and ethanol yield over PTh/Bi{sub 2}WO{sub 6} was 56.5 and 20.5 μmol g{sub cat}{sup −1} in 4 h, respectively. The total yield of hydrocarbons is 2.8 times higher than that over pure Bi{sub 2}WO{sub 6}. It is noted that the catalyst exhibits good recyclability and stability. After five consecutive runs, the PTh/Bi{sub 2}WO{sub 6} catalyst shows no significant loss of photocatalytic activity. The possible photocatalytic mechanism was proposed which is beneficial for further improving the activity of photocatalysts. The approach described in this study provides a simple and reliable strategy for the rational design of efficient visible light-driven photocatalysts for photoreduction of CO{sub 2} to hydrocarbons.

  14. Synthesis of WO{sub n}-WX{sub 2} (n=2.7, 2.9; X=S, Se) heterostructures for highly efficient green quantum dot light-emitting diodes

    Energy Technology Data Exchange (ETDEWEB)

    Han, Shikui; Tan, Chaoliang; Zhang, Xiao; Chen, Junze; Huang, Ying; Chen, Bo; Luo, Zhimin; Ma, Qinglang; Sindoro, Melinda; Zhang, Hua [Center for Programmable Materials, School of Materials Science and Engineering, Nanyang Technological University, Singapore (Singapore); Yang, Xuyong [Luminous. Center of Excellence for Semiconductor Lighting and Displays, School of Electrical and Electronic Engineering, Nanyang Technological University, Singapore (Singapore); Zhu, Yihan; Han, Yu [Advanced Membranes and Porous Materials Center, Physical Sciences and Engineering Division, King Abdullah University of Science and Technology, Thuwal (Saudi Arabia); Zhang, Hao; Li, Hai; Huang, Xiao; Huang, Wei [Institute of Advanced Materials (IAM), Nanjing Tech University (NanjingTech) (China); Qi, Xiaoying [Singapore Institute of Manufacturing Technology, Singapore (Singapore); Sun, Xiao Wei [Luminous. Center of Excellence for Semiconductor Lighting and Displays, School of Electrical and Electronic Engineering, Nanyang Technological University, Singapore (Singapore); Dept. of Electrical and Electronic Engineering, College of Engineering, Southern Univ. of Science and Technology, Nanshan, Shenzhen, Guangdong (China)

    2017-08-21

    Preparation of two-dimensional (2D) heterostructures is important not only fundamentally, but also technologically for applications in electronics and optoelectronics. Herein, we report a facile colloidal method for the synthesis of WO{sub n}-WX{sub 2} (n=2.7, 2.9; X=S, Se) heterostructures by sulfurization or selenization of WO{sub n} nanomaterials. The WO{sub n}-WX{sub 2} heterostructures are composed of WO{sub 2.9} nanoparticles (NPs) or WO{sub 2.7} nanowires (NWs) grown together with single- or few-layer WX{sub 2} nanosheets (NSs). As a proof-of-concept application, the WO{sub n}-WX{sub 2} heterostructures are used as the anode interfacial buffer layer for green quantum dot light-emitting diodes (QLEDs). The QLED prepared with WO{sub 2.9} NP-WSe{sub 2} NS heterostructures achieves external quantum efficiency (EQE) of 8.53 %. To our knowledge, this is the highest efficiency in the reported green QLEDs using inorganic materials as the hole injection layer. (copyright 2017 Wiley-VCH Verlag GmbH and Co. KGaA, Weinheim)

  15. Low-cost fabrication of WO{sub 3} films using a room temperature and low-vacuum air-spray based deposition system for inorganic electrochromic device applications

    Energy Technology Data Exchange (ETDEWEB)

    Park, Sung-Ik [Department of Mechanical and Aerospace Engineering, Seoul National University, Seoul (Korea, Republic of); Kim, Sooyeun, E-mail: sooyeunk@u.washington.edu [Department of Mechanical Engineering, University of Washington, Seattle, WA (United States); Choi, Jung-Oh; Song, Ji-Hyeon [Department of Mechanical and Aerospace Engineering, Seoul National University, Seoul (Korea, Republic of); Taya, Minoru [Department of Mechanical Engineering, University of Washington, Seattle, WA (United States); Ahn, Sung-Hoon, E-mail: ahnsh@snu.ac.kr [Department of Mechanical and Aerospace Engineering, Seoul National University, Seoul (Korea, Republic of); Institute of Advanced Machines and Design, Seoul (Korea, Republic of)

    2015-08-31

    We report the deposition of tungsten oxide (WO{sub 3}) thin films on fluorine-doped tin oxide (FTO) and indium-doped tin oxide (ITO) glass substrates by using a room-temperature deposition system based on low-vacuum air-spray for the fabrication of inorganic electrochromic windows. The structure of the WO{sub 3} films was characterized using X-ray diffraction, and the surface morphology and film thickness were investigated using scanning electron microscopy and atomic force microscopy. The color of the prepared WO{sub 3} films changed from slight yellow to dark blue under applied voltages, demonstrating electrochromism. The WO{sub 3} film coated FTO glass exhibited a large electrochromic contrast of up to 50% at a wavelength of 800 nm. The electrochemical properties of the films were examined using cyclic voltammetry and chronocoulometry. - Highlights: • WO{sub 3} thin films were fabricated using an air-spray based deposition system at room temperature under low-vacuum conditions. • Dry WO{sub 3} particles were directly deposited on FTO and ITO glasses by using a low-cost deposition system. • The FTO glass based WO{sub 3} film showed the optical contrast of 50% at a wavelength of 800 nm.

  16. Evaluation of ilmenite serpentine concrete and ordinary concrete as nuclear reactor shielding

    International Nuclear Information System (INIS)

    Abulfaraj, W.H.; Kamal, S.M.

    1994-01-01

    The present study involves adapting a formal decision methodology to the selection of alternative nuclear reactor concrete shielding. Multiattribute utility theory is selected to accommodate decision maker's preferences. Multiattribute utility theory (MAU) is here employed to evaluate two appropriate nuclear reactor shielding concretes in terms of effectiveness to determine the optimal choice in order to meet the radiation protection regulations. These concretes are Ordinary concrete (O.C.) and Illmenite Serpentile concrete (I.S.C.). These are normal weight concrete and heavy weight heat resistive concrete, respectively. The effectiveness objective of the nuclear reactor shielding is defined and structured into definite attributes and subattributes to evaluate the best alternative. Factors affecting the decision are dose received by reactor's workers, the material properties as well as cost of concrete shield. A computer program is employed to assist in performing utility analysis. Based upon data, the result shows the superiority of Ordinary concrete over Illmenite Serpentine concrete. (Author)

  17. Thermal oxidation of seeds for the hydrothermal growth of WO3 nanorods on ITO glass substrate

    International Nuclear Information System (INIS)

    Ng, Chai Yan; Abdul Razak, Khairunisak; Lockman, Zainovia

    2015-01-01

    This work reports a simple seed formation method for the hydrothermal growth of tungsten oxide (WO 3 ) nanorods. A WO 3 seed layer was prepared by thermal oxidation, where a W-sputtered substrate was heated and oxidized in a furnace. Oxidation temperatures and periods were varied at 400–550 °C and 5–60 min, respectively, to determine an appropriate seed layer for nanorod growth. Thermal oxidation at 500 °C for 15 min was found to produce a seed layer with sufficient crystallinity and good adhesion to the substrate. These properties prevented the seed from peeling off during the hydrothermal process, thereby allowing nanorod growth on the seed. The nanorod film showed better electrochromic behavior (higher current density of − 1.11 and + 0.65 mA cm −2 ) than compact film (lower current density of − 0.54 and + 0.28 mA cm −2 ). - Highlights: • A simple seed formation method (thermal oxidation) on sputtered W film is reported. • Crystalline seed with good adhesion to substrate is required for nanorod growth. • The appropriate temperature and period for seed formation were 500 °C and 15 min. • WO 3 nanorods exhibited higher electrochromic current density than WO 3 compact film.

  18. Progress in PbWO4 scintillating crystal

    International Nuclear Information System (INIS)

    Fyodorov, A.; Korzhik, M.; Missevitch, O.; Pavlenko, V.; Kachanov, V.; Singovsky, A.; Annenkov, A.N.; Ligun, V.A.; Peigneux, J.P.; Vialle, J.P.

    1994-12-01

    Lead tungstate PbWO 4 (PWO) has recently been shown to be a promising scintillating material for precise electromagnetic calorimetry. Modifications of PWO technology were made to improve the uniformity of the crystal properties. A model of the scintillation mechanism for PWO was developed and served to guide the improvement. The complex spectroscopic analysis of the crystal after improvement is presented, as well as the new crystal properties achieved. (K.A.). 14 refs., 14 figs., 4 tabs

  19. Towards Better Understanding of Concrete Containing Recycled Concrete Aggregate

    Directory of Open Access Journals (Sweden)

    Hisham Qasrawi

    2013-01-01

    Full Text Available The effect of using recycled concrete aggregates (RCA on the basic properties of normal concrete is studied. First, recycled aggregate properties have been determined and compared to those of normal aggregates. Except for absorption, there was not a significant difference between the two. Later, recycled aggregates were introduced in concrete mixes. In these mixes, natural coarse aggregate was partly or totally replaced by recycled aggregates. Results show that the use of recycled aggregates has an adverse effect on the workability and air content of fresh concrete. Depending on the water/cement ratio and on the percent of the normal aggregate replaced by RCA, the concrete strength is reduced by 5% to 25%, while the tensile strength is reduced by 4% to 14%. All results are compared with previous research. As new in this research, the paper introduces a simple formula for the prediction of the modulus of elasticity of RCA concrete. Furthermore, the paper shows the variation of the air content of RAC.

  20. Characterization of scintillating CaWO{sub 4} crystals for the CRESST experiment using two-photon excitation

    Energy Technology Data Exchange (ETDEWEB)

    Hampf, Raphael; Dandl, Thomas; Muenster, Andrea; Oberauer, Lothar; Roth, Sabine; Schoenert, Stefan; Ulrich, Andreas [Physik-Department and Excellence Cluster Universe, Technische Universitaet Muenchen, D-85747 Garching (Germany)

    2016-07-01

    In the CRESST experiment for direct dark matter search, phonon and photon signals from cryogenic CaWO{sub 4} crystals are used to search for WIMP-induced nuclear recoil events. We present a novel table-top setup in which the scintillation of CaWO{sub 4} is induced by 0.7 ns laser pulses of 355 nm wavelength. The excitation occurs via two-photon absorption in the bulk material. The scintillation light is observed by time resolved optical spectroscopy. By varying the focusing of the laser-beam the excitation density can be made high enough to study quenching effects due to exciton-exciton annihilation. This allows to perform experiments to test models for the quenching factors of different ionizing projectiles in CaWO{sub 4} which are used to identify these projectiles on an event by event basis.

  1. Ag/AgCl Loaded Bi2WO6 Composite: A Plasmonic Z-Scheme Visible Light-Responsive Photocatalyst

    Directory of Open Access Journals (Sweden)

    Xiangchao Meng

    2016-01-01

    Full Text Available Hierarchical flower-like Bi2WO6 was successfully synthesized by facile hydrothermal method at low pH. And Ag/AgCl was loaded by photoreduction on its surface. As-prepared photocatalysts were characterized by various techniques. Bi2WO6 was successfully synthesized at a size of 2-3 μm. Depositing Ag/AgCl did not destroy the crystal structure, and both Ag+ and metallic Ag0 were found. The band gap of the composite was 2.57 eV, which indicates that visible light could be the activating irradiation. In the photocatalytic activity test, the composite with 10 wt% Ag/AgCl boasted the highest removal efficiency (almost 100% in 45 min. The significant enhancement can be attributed to the surface plasmon resonance (SPR effect and the establishment of heterostructures between Ag/AgCl and Bi2WO6. A possible mechanism of photocatalytic oxidation in the presence of Ag/AgCl-Bi2WO6 was proposed. This work sheds light on the potential applications of plasmonic metals in photocatalysis to enhance their activities.

  2. Degradation of dimethylformamide on the surface of the nanosized WO{sub 3} films studied by infrared spectroscopy

    Energy Technology Data Exchange (ETDEWEB)

    Gavrilyuk, A.I., E-mail: gavrilyuk@mail.ioffe.ru

    2016-07-30

    Highlights: • Dimethylformamide was adsorbed on the surface of the nanosized WO{sub 3} films. • The mechanism of the adsorption was investigated by IR spectroscopy. • The transformations of the adsorbed molecules either in dark or under the action of light was discussed. - Abstract: Here I report on the degradation of dimethylformamide on the surface of the nanosized WO{sub 3} films under the action of light. Dimethylformamide, a substance that has a series of interesting properties, was adsorbed on the surface of the WO{sub 3} films and its adsorption mechanism and transformations under the action of light have been investigated with the help of the IR spectroscopy. The spirit of the research is that both DMF modifications have been used i.e., conventional and that with the substitution of hydrogen atoms by deuterium. Formation of two weak bonds (donor-acceptor bond and hydrogen bond) provides a great catalytic effect for photo-initiated proton-coupled electron transfer from the adsorbed molecules to the WO{sub 3} film surface. The mechanism of the detachment of hydrogen atoms and subsequent transformation of the adsorbed molecules has been investigated and discussed.

  3. Global coordination and standardisation in marine biodiversity through the World Register of Marine Species (WoRMS and related databases.

    Directory of Open Access Journals (Sweden)

    Mark J Costello

    Full Text Available The World Register of Marine Species is an over 90% complete open-access inventory of all marine species names. Here we illustrate the scale of the problems with species names, synonyms, and their classification, and describe how WoRMS publishes online quality assured information on marine species. Within WoRMS, over 100 global, 12 regional and 4 thematic species databases are integrated with a common taxonomy. Over 240 editors from 133 institutions and 31 countries manage the content. To avoid duplication of effort, content is exchanged with 10 external databases. At present WoRMS contains 460,000 taxonomic names (from Kingdom to subspecies, 368,000 species level combinations of which 215,000 are currently accepted marine species names, and 26,000 related but non-marine species. Associated information includes 150,000 literature sources, 20,000 images, and locations of 44,000 specimens. Usage has grown linearly since its launch in 2007, with about 600,000 unique visitors to the website in 2011, and at least 90 organisations from 12 countries using WoRMS for their data management. By providing easy access to expert-validated content, WoRMS improves quality control in the use of species names, with consequent benefits to taxonomy, ecology, conservation and marine biodiversity research and management. The service manages information on species names that would otherwise be overly costly for individuals, and thus minimises errors in the application of nomenclature standards. WoRMS' content is expanding to include host-parasite relationships, additional literature sources, locations of specimens, images, distribution range, ecological, and biological data. Species are being categorised as introduced (alien, invasive, of conservation importance, and on other attributes. These developments have a multiplier effect on its potential as a resource for biodiversity research and management. As a consequence of WoRMS, we are witnessing improved

  4. Global Coordination and Standardisation in Marine Biodiversity through the World Register of Marine Species (WoRMS) and Related Databases

    Science.gov (United States)

    Bouchet, Philippe; Boxshall, Geoff; Fauchald, Kristian; Gordon, Dennis; Hoeksema, Bert W.; Poore, Gary C. B.; van Soest, Rob W. M.; Stöhr, Sabine; Walter, T. Chad; Vanhoorne, Bart; Decock, Wim

    2013-01-01

    The World Register of Marine Species is an over 90% complete open-access inventory of all marine species names. Here we illustrate the scale of the problems with species names, synonyms, and their classification, and describe how WoRMS publishes online quality assured information on marine species. Within WoRMS, over 100 global, 12 regional and 4 thematic species databases are integrated with a common taxonomy. Over 240 editors from 133 institutions and 31 countries manage the content. To avoid duplication of effort, content is exchanged with 10 external databases. At present WoRMS contains 460,000 taxonomic names (from Kingdom to subspecies), 368,000 species level combinations of which 215,000 are currently accepted marine species names, and 26,000 related but non-marine species. Associated information includes 150,000 literature sources, 20,000 images, and locations of 44,000 specimens. Usage has grown linearly since its launch in 2007, with about 600,000 unique visitors to the website in 2011, and at least 90 organisations from 12 countries using WoRMS for their data management. By providing easy access to expert-validated content, WoRMS improves quality control in the use of species names, with consequent benefits to taxonomy, ecology, conservation and marine biodiversity research and management. The service manages information on species names that would otherwise be overly costly for individuals, and thus minimises errors in the application of nomenclature standards. WoRMS' content is expanding to include host-parasite relationships, additional literature sources, locations of specimens, images, distribution range, ecological, and biological data. Species are being categorised as introduced (alien, invasive), of conservation importance, and on other attributes. These developments have a multiplier effect on its potential as a resource for biodiversity research and management. As a consequence of WoRMS, we are witnessing improved communication within the

  5. Hydrothermal synthesis of WO{sub 3}·0.5H{sub 2}O microtubes with excellent photocatalytic properties

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Xiaozhou; Meng, Xiuqing, E-mail: xqmeng@semi.ac.cn; Zhong, Mianzeng; Wu, Fengmin; Li, Jingbo, E-mail: jbli@semi.ac.cn

    2013-10-01

    Pyrochlore WO{sub 3} microtubes were synthesized via a hydrothermal method for the first time. In this process, thiourea was employed to overcome the hydrogen bonds on the rim of WO{sub 3}·0.5H{sub 2}O and hydroxylamine hydrochloride was used as a viscosity regulator. Field-emission scanning electron microscopy and high-resolution transmission electron microscopy observations revealed that large amounts of uniform single-crystal WO{sub 3}·0.5H{sub 2}O microtubes with diameters ranging from 100 to 300 nm and length of tens of micrometers were obtained. The thickness of the tube wall was about 40 nm. A possible rolling mechanism was proposed to explain the formation of the tubular structures, and the influence of thiourea and hydroxylamine hydrochloride on the uniform tubular morphology was discussed. The WO{sub 3}·0.5H{sub 2}O microtubes showed excellent photocatalytic activity toward the degradation of organic molecules such as RhB, which may find potential applications in the fields of photocatalysts, sensors and transistors.

  6. Photogenerated cathode protection properties of nano-sized TiO2/WO3 coating

    International Nuclear Information System (INIS)

    Zhou Minjie; Zeng Zhenou; Zhong Li

    2009-01-01

    Nano-sized TiO 2 /WO 3 bilayer coatings were prepared on type 304 stainless steel substrate by sol-gel method. The performance of photo-electrochemical and photogenerated cathode protection of the coating was investigated by the electrochemical method. The results show that the bilayer coating with four TiO 2 layers and three WO 3 layers exhibits the highest photo-electrochemical efficiency and the best corrosion resistance property. Type 304 stainless steel with the coating can maintain cathode protection for 6 h in the dark after irradiation by UV illumination for 1 h. In addition, the mechanism of the photogenerated cathode protection for the bilayer coating was also explored.

  7. Synthesis, formation mechanism and sensing properties of WO3 hydrate nanowire netted-spheres

    International Nuclear Information System (INIS)

    Yan, Aihua; Xie, Changsheng; Zeng, Dawen; Cai, Shuizhou; Hu, Mulin

    2010-01-01

    Tungsten oxide hydrate nanowire netted-spheres were successfully synthesized in the glycol solution using a facile solvothermal approach. The nanowires with uniform diameter of 4-6 nm are actually a kind of tungsten oxide hydrate/surfactant hybrid materials. The influence of surfactant, solvent, time and temperature on tailoring morphology was investigated in detail. The possible formation process of WO 3 hydrate nanowire netted-sphere was proposed. Sensing properties of such WO 3 hydrate sensor show that the desirable sensing characteristics towards 100 ppm ammonia gas at 320 o C were obtained, such as rapid response (18.3 s), high sensitivity, good reproducibility and stability.

  8. Facile preparation of hexagonal WO{sub 3}·0.33H{sub 2}O/C nanostructures and its electrochemical properties for lithium-ion batteries

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Zhiwei [Institute for Advanced Materials and Technology, University of Science and Technology Beijing, Beijing 100083 (China); Li, Ping, E-mail: ustbliping@126.com [Institute for Advanced Materials and Technology, University of Science and Technology Beijing, Beijing 100083 (China); Dong, Yuan [Institute for Advanced Materials and Technology, University of Science and Technology Beijing, Beijing 100083 (China); Wan, Qi [Energy Material & Technology Research Institute, General Research Institute for Nonferrous Metal, Beijing 100088 (China); Zhai, Fuqiang [Departament Física Aplicada, EETAC, Universitat Politècnica de Catalunya – Barcelona Tech, 08860 Castelldefels (Spain); Volinsky, Alex A. [Department of Mechanical Engineering, University of South Florida, Tampa, FL 33620 (United States); Qu, Xuanhui [Institute for Advanced Materials and Technology, University of Science and Technology Beijing, Beijing 100083 (China)

    2017-02-01

    Highlights: • WO{sub 3}·0.33H{sub 2}O/C was prepared by the facile synthesis & hydrothermal method. • WO{sub 3}·0.33H{sub 2}O/C electrode capacity is higher than the reported orthorhombic WO{sub 3}·0.33H{sub 2}O. • The specific structure can provide efficient channels for the fast transport of Li{sup +}. - Abstract: Nano-sized hexagonal WO{sub 3}·0.33H{sub 2}O/C is prepared by the solution combustion synthesis & hydrothermal method. This material has been used as the anode for high performance lithium-ion batteries for the first time. Carbon layer is uniformly coated on hexagonal WO{sub 3}·0.33H{sub 2}O nanoparticles. The samples are characterized by X-ray diffraction (XRD), thermal analysis (TG-DSC), Raman spectra, scanning and transmission electron microscopy (FESEM and TEM). Electrochemical properties are studied by cyclic voltammetry and galvanostatic charge/discharge cycling. Prepared WO{sub 3}·0.33H{sub 2}O/C electrode shows high and reversible capacity of 768 mAh g{sup −1} after 200 cycles at 100 mA g{sup −1}, which is higher than the reported orthorhombic WO{sub 3}·0.33H{sub 2}O. The specific structure can provide efficient channels for transporting Li{sup +} swiftly. Therefore, hexagonal WO{sub 3}·0.33H{sub 2}O/C shows a great potential as the anode material for lithium-ion batteries.

  9. Evaluation of recycled concrete as aggregate in new concrete pavements.

    Science.gov (United States)

    2014-04-01

    This study evaluated the use of recycled concrete as coarse aggregate in new concrete pavements. : Recycled concrete aggregate (RCA) produced from demolished pavements in three geographically dispersed locations in Washington state were used to perfo...

  10. Synthesis, strong room-temperature PL and photocatalytic activity of ZnO/ZnWO{sub 4} rod-like nanoparticles

    Energy Technology Data Exchange (ETDEWEB)

    Validzic, Ivana Lj., E-mail: validzic@vinca.rs [Vinca Institute of Nuclear Sciences, University of Belgrade, P.O. Box 522, 11001 Belgrade (Serbia); Savic, Tatjana D.; Krsmanovic, Radenka M.; Jovanovic, Dragana J.; Novakovic, Mirjana M.; Popovic, Maja C.; Comor, Mirjana I. [Vinca Institute of Nuclear Sciences, University of Belgrade, P.O. Box 522, 11001 Belgrade (Serbia)

    2012-05-25

    Highlights: Black-Right-Pointing-Pointer Novel low temperature method for the synthesis of ZnO/ZnWO{sub 4} rod-like nanoparticles. Black-Right-Pointing-Pointer PL showed strong UV band peaked at 3.30 eV and a visible band at 2.71 and 2.53 eV. Black-Right-Pointing-Pointer Variations of the two PL bands were observed for different excitation wavelengths. Black-Right-Pointing-Pointer Band-gap energies of ZnO/ZnWO{sub 4} nanoparticles were found to be 3.62 and 3.21 eV. Black-Right-Pointing-Pointer Photocatalytic behaviour of ZnO is dependent on the formation of ZnWO{sub 4} phase. - Abstract: Zinc oxide (ZnO)/zinc tungstate (ZnWO{sub 4}) rod-like nanoparticles with diameters in the range of 6-11 nm and length of about 30 nm were synthesized by a low temperature soft solution method at 95 Degree-Sign C in the presence of non-ionic copolymer surfactant. It was found that their crystallinity was enhanced with the increase of heating time from 1 h up to 120 h. The photoluminescence (PL) measurements showed very strong, narrow UV band peaked at 3.30 eV and a broad visible band peaking at 2.71 eV with a shoulder at about 2.53 eV, for {lambda}{sub exc} < 300 nm. Quite large variations in the intensities of the two PL bands were observed for different excitation wavelengths. The intensity of the main visible band decreases with decreasing excitation energy and disappears when samples are excited {lambda} = 320 nm (E{sub exc} = 3.875 eV). We found that observed optical properties originate from ZnO phase. UV band gap PL had high intensity for all applied excitations, probably induced by ZnWO{sub 4} phase presence on the surface. In addition, two values were found for direct band-gap energy of ZnO/ZnWO{sub 4} rod-like nanoparticles 3.62 and 3.21 eV, determined from reflectance spectrum. The photocatalytic behaviour of ZnO is strongly dependent on the formation of ZnWO{sub 4} phase, of the obtained rod-like nanoparticles.

  11. Isolation of basal membrane proteins from BeWo cells and their expression in placentas from fetal growth-restricted pregnancies.

    Science.gov (United States)

    Oh, Soo-Young; Hwang, Jae Ryoung; Lee, Yoonna; Choi, Suk-Joo; Kim, Jung-Sun; Kim, Jong-Hwa; Sadovsky, Yoel; Roh, Cheong-Rae

    2016-03-01

    The syncytiotrophoblast, a key barrier between the mother and fetus, is a polarized epithelium composed of a microvillus and basal membrane (BM). We sought to characterize BM proteins of BeWo cells in relation to hypoxia and to investigate their expression in placentas from pregnancies complicated by fetal growth restriction (FGR). We isolated the BM fraction of BeWo cells by the cationic colloidal silica method and identified proteins enriched in this fraction by mass spectrometry. We evaluated the effect of hypoxia on the expression and intracellular localization of identified proteins and compared their expression in BM fractions of FGR placentas to those from normal pregnancies. We identified BM proteins from BeWo cells. Among BM proteins, we further characterized heme oxygenase-1 (HO-1), voltage-dependent anion channel-1 (VDAC1), and ribophorin II (RPN2), based on their relevance to placental biology. Hypoxia enhanced the localization of these proteins to the BM of BeWo cells. HO-1, VDAC1, and RPN2 were selectively expressed in the human placental BM fraction. C-terminally truncated HO-1 was identified in placental BM fractions, and its BM expression was significantly reduced in FGR placentas than in normal placentas. Interestingly, a truncated HO-1 construct was predominantly localized in the BM in response to hypoxia and co-localized with VDAC1 in BeWo cells. Hypoxia increased the BM localization of HO-1, VDAC1, and RPN2 proteins. FGR significantly reduced the expression of truncated HO-1, which was surmised to co-localize with VDAC1 in hypoxic BeWo cells. Copyright © 2016 Elsevier Ltd. All rights reserved.

  12. Development of w/o microemulsion for transdermal delivery of iodide ions.

    Science.gov (United States)

    Lou, Hao; Qiu, Ni; Crill, Catherine; Helms, Richard; Almoazen, Hassan

    2013-03-01

    The objective of this study was to develop a water-in-oil (w/o) microemulsion which can be utilized as a transdermal delivery for iodide ions. Several w/o microemulsion formulations were prepared utilizing Span 20, ethanol, Capryol 90®, and water. The selected formulations had 5%, 10%, 15%, 20%, and a maximum of 23% w/w water content. Potassium iodide (KI) was incorporated in all formulations at 5% w/v. Physicochemical characterizations were conducted to evaluate the structure and stability. These studies included: mean droplet size, pH, viscosity, conductivity, and chemical stability tests. In vitro human skin permeation studies were conducted to evaluate the diffusion of the iodide ion through human skin. The w/o microemulsion formulations were stable and compatible with iodide ions with water content ranging from 5% to 23% w/w. The addition of KI influenced the physicochemical properties of microemulsion as compared to blank microemulsion formulations. In vitro human skin permeation studies indicated that selected formulations improved iodide ion diffusion significantly as compared to control (KI solution; P valuemicroemulsion. Span 20, ethanol and Capryol 90 protected the iodide ions against oxidation and formed a stable microemulsion. It is worth to note that according to Hofmeister series, iodide ions tend to lower the interfacial tension between water and oil and consequently enhance overall stability. This work illustrates that microemulsion system can be utilized as a vehicle for the transdermal administration of iodide.

  13. Europium doping in monoclinic KYb(WO{sub 4}){sub 2} crystal

    Energy Technology Data Exchange (ETDEWEB)

    Loiko, P.A. [Física i Cristallografia de Materials i Nanomaterials (FiCMA-FiCNA), Universitat Rovira i Virgili (URV), Campus Sescelades, c/ Marcellí Domingo, s/n., Tarragona, Spain E-43007 (Spain); Center for Optical Materials and Technologies (COMT), Belarusian National Technical University, 65/17 Nezavisimosti Ave., Minsk 220013 (Belarus); Vilejshikova, E.V. [Center for Optical Materials and Technologies (COMT), Belarusian National Technical University, 65/17 Nezavisimosti Ave., Minsk 220013 (Belarus); Mateos, X., E-mail: xavier.mateos@urv.cat [Física i Cristallografia de Materials i Nanomaterials (FiCMA-FiCNA), Universitat Rovira i Virgili (URV), Campus Sescelades, c/ Marcellí Domingo, s/n., Tarragona, Spain E-43007 (Spain); Serres, J.M. [Física i Cristallografia de Materials i Nanomaterials (FiCMA-FiCNA), Universitat Rovira i Virgili (URV), Campus Sescelades, c/ Marcellí Domingo, s/n., Tarragona, Spain E-43007 (Spain); Dunina, E.B.; Kornienko, A.A. [Vitebsk State Technological University, 72 Moskovskaya Ave., Vitebsk 210035 (Belarus); Yumashev, K.V. [Center for Optical Materials and Technologies (COMT), Belarusian National Technical University, 65/17 Nezavisimosti Ave., Minsk 220013 (Belarus); Aguiló, M.; Díaz, F. [Física i Cristallografia de Materials i Nanomaterials (FiCMA-FiCNA), Universitat Rovira i Virgili (URV), Campus Sescelades, c/ Marcellí Domingo, s/n., Tarragona, Spain E-43007 (Spain)

    2017-03-15

    We report on a detailed spectroscopic study of Eu{sup 3+} ions in the monoclinic KYb(WO{sub 4}){sub 2} crystal. The polarized room and low-temperature absorption spectra are measured. The maximum σ{sub abs} corresponding to the {sup 7}F{sub 1} → {sup 5}D{sub 1} transition is 1.32×10{sup –20} cm{sup 2} at 534.2 nm with a bandwidth of 0.7 nm (for E||N{sub m}). The Stark sub-levels of the excited mulitplets are determined. A Judd-Ofelt analysis is applied to the Eu{sup 3+}:KYb(WO{sub 4}){sub 2} crystal to determine the probability of spontaneous transitions, radiative lifetimes and luminescence branching ratios. Within the strong configuration interaction (SCI) approximation, the intensity parameters are Ω{sub 2}=4.757, Ω{sub 4}=2.295, Ω{sub 6}=1.644 [10{sup –20} cm{sup 2}] and Δ{sub f}=50160 cm{sup –1}. The radiative lifetime of the {sup 5}D{sub 0} state is 351 µs. The maximum stimulated-emission cross-section corresponding to the {sup 7}F{sub 1} → {sup 5}D{sub 1} transition is 1.44×10{sup –20} cm{sup 2} at 703.2 nm (for E||N{sub m}). Under UV excitation, the Eu{sup 3+}:KYb(WO{sub 4}){sub 2} crystal provides intense red photoluminescence with CIE coordinates, x=0.675, y=0.325.

  14. Nodal head method with matric operation in analysis of mine ventilation networks. Matrics kaiho wo mochiita setten ho ni yoru tsuki mo kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    Sasaki, K.; Miyakoshi, H. (Akita Univ., Akita (Japan). Mining College); Kinoshita, H.; Onozuka, T. (Hanaoka Mining Co. Ltd., Akita (Japan))

    1990-09-25

    In this report, the method of analyzing mine ventilation networks is explained in which the direct matric operation method is applied to the solution of the linear equation system introduced from the fundamental equation of the nodal head method. In other words, the fundamental equation was expressed by genelarized equation composition by using connecting functions between nodes and the algorism of a computer program was clarified. And the calculation method necessary for other ventilation netwrks analysis was shown in a concrete form. For solving the linear equation system, the matric operation method based on the modified Choleski's method was used in order to speed up the calculation and stabilize the convergence process of the solution. As examples, calculation was made on the ventilation networks of total numbers of the nodes of 8, 14, 51 and 141. From these ventilation network analyses, using a linear equation system concerning the nodal pressure correction, it was found that in the system with convergence acceleration coefficient of 1.4, the number of sequential repeating frequency of approximation Mc which was required for convergence was in the order of Mc {approx equal} 13 (cycle) for the condition that the fan pressure was constant and the convergence condition was {vert bar} AQi {vert bar}{sub max} {lt} 0.1m {sup 3}/min. 14 refs., 12 figs., 3 tabs.

  15. IR spectra and structure of glasses in the BaO-WO3-P2O5 system

    International Nuclear Information System (INIS)

    Miroshnichenko, O.Ya.; Mombelli, V.V.

    1979-01-01

    Studied are IR absorption spectra and determined are the main structural characteristics of tungstophosphate glasses of the BaO-WO 3 -P 2 O 5 system in all the area of glass formation. It is shown that the main structural components of their anion network are phosphate chains consisting of PO 4 tetrahedrons and tungstate chains consisting of WO 4 tetrahedrons and of WO 6 octahedrons. These chains are connected by P-O-W bridges into three-dimentional tungstophosphate network, where the ratio of phosphate and tungstate structural units and their polymerization degree change without limits depending on the glass composition. Analysis of concentration frequency dependence and spectral band intensity permit to clarify the effect of each component on the glass structure in all the area of glass formation of the triple system

  16. Automatic dam concrete placing system; Dam concrete dasetsu sagyo no jidoka system

    Energy Technology Data Exchange (ETDEWEB)

    Yoneda, Y; Hori, Y; Nakayama, T; Yoshihara, K; Hironaka, T [Okumura Corp., Osaka (Japan)

    1994-11-15

    An automatic concrete placing system was developed for concrete dam construction. This system consists of the following five subsystems: a wireless data transmission system, an automatic dam concrete mixing system, a consistency determination system, an automatic dam concrete loading and transporting system, and a remote concrete bucket opening and closing system. The system includes the following features: mixing amount by mixing ratio and mixing intervals can be instructed from a concrete placing site by using a wireless handy terminal; concrete is mixed automatically in a batcher plant; a transfer car is started, and concrete is charged into a bucket automatically; the mixed concrete is determined of its properties automatically; labor cost can be reduced, the work efficiency improved, and the safety enhanced; and the system introduction has resulted in unattended operation from the aggregate draw-out to a bunker line, manpower saving of five persons, and reduction in cycle time by 10%. 11 figs., 2 tabs.

  17. Controllable synthesis of Bi{sub 2}WO{sub 6} nanoplate self-assembled hierarchical erythrocyte microspheres via a one-pot hydrothermal reaction with enhanced visible light photocatalytic activity

    Energy Technology Data Exchange (ETDEWEB)

    Yang, Zhenya; Huang, Lin; Xie, Yanyu; Lin, Zheguan; Fan, Yunyan; Liu, Dan; Chen, Lu; Zhang, Zizhong, E-mail: z.zhang@fzu.edu.cn; Wang, Xuxu

    2017-05-01

    Highlights: • Bi{sub 2}WO{sub 6} hierarchical erythrocyte structure was designed by F{sup −}-assisted one-pot reaction. • Erythrocyte structure enhanced the visible-light photocatalytic activity of Bi{sub 2}WO{sub 6}. • Superoxide radical anions and h{sup +} were the main active species for RhB degradation. - Abstract: This work provides a simple approach of the F{sup −}-assisted one-pot hydrothermal reaction to successfully synthesize Bi{sub 2}WO{sub 6} hierarchical erythrocyte microspheres. The importance role of F{sup −} was systematically investigated by comparing different type of halogen ions, hydrothermal temperature and time. The possible growth mechanism of Bi{sub 2}WO{sub 6} hierarchical structures was proposed. The hierarchical erythrocytes were formed through the well-ordered and oriented self-assembly of thin Bi{sub 2}WO{sub 6} nanoplate primary subunits. F{sup −} ions were absorbed on Bi{sub 2}WO{sub 6} nanoplate surface to suppress the nanoplate stack but to induce a self-assembly through the edge interaction of Bi{sub 2}WO{sub 6} nanoplates into erythrocyte-like hierarchical microspheres superstructures. This erythrocyte structure narrowed the band gap energy and enhanced the visible-light photocatalytic activity of Bi{sub 2}WO{sub 6}. Moreover, superoxide radical anions and h{sup +} were revealed as the main active species responding for the RhB degradation on Bi{sub 2}WO{sub 6} under visible light irradiation.

  18. Sliding charge density wave in the monophosphate tungsten bronze (PO2)4(WO3)2m with alternate stacking of m=4 and m=6 WO3 layers

    International Nuclear Information System (INIS)

    Foury-Leylekian, P.; Sandre, E.; Ravy, S.; Pouget, J.-P.; Elkaim, E.; Roussel, P.; Groult, D.; Labbe, Ph.

    2002-01-01

    The monophosphate tungsten bronzes (PO 2 ) 4 (WO 3 ) 2m form family of two-dimensional metals which exhibit charge density wave (CDW) instabilities. These materials are generally built by the regular stacking of (a,b) layers in which chains made of segments of m WO 6 octahedra directed along the a and a±b directions are delimited. Their electronic structure thus originates from quasi-one-dimensional (1D) bands located on these chains. As a consequence their Fermi surface (FS) exhibits large flat portions whose nesting gives rise to successive CDW instabilities. Here we present a structural study of the CDW instability of the (PO 2 ) 4 (WO 3 ) 10 member formed by the alternate stacking of layers built with segments of m=4 and m=6 WO 6 octahedra. Its ab initio electronic structure calculation shows that the FS of this member exhibits large flat portions which can be extremely well nested. Its best nesting wave vector accounts for the modulation wave vector stabilized by the CDW transition which occurs at 156 K. Because of the regular stacking of layers of different m values the FS is slightly split. The unusual thermal dependence of the x-ray satellite intensity provides evidence that the two types of layers become modulated at different temperature. This also leads to a slight thermal sliding of the CDW-nesting modulation wave vector, which can be accounted for within the framework of a Landau-Ginzburg theory. In addition, the observation of a global hysteresis in the thermal cycling of the satellite intensity, as well as the degradation of the interlayer order upon cooling, suggest the formation of a disordered lattice of dilute solitons. Such solitons allow to accommodate the charge transferred between the two types of layer. Finally the relevance of local charge transfers, at intergrowth defects, for example, to create pinned discommensurations that break the CDW coherence is emphasized in this whole family of bronzes

  19. Recycled concrete aggregate in portland cement concrete.

    Science.gov (United States)

    2013-01-01

    Aggregates can be produced by crushing hydraulic cement concrete and are known as recycled concrete : aggregates (RCA). This report provides results from a New Jersey Department of Transportation study to identify : barriers to the use of RCA in new ...

  20. Analysis of Possibilities for Using Recycled Concrete Aggregate in Concrete Pavement

    OpenAIRE

    R. Pernicova; D. Dobias

    2016-01-01

    The present article describes the limits of using recycled concrete aggregate (denoted as RCA) in the top layer of concrete roads. The main aim of this work is to investigate the possibility of reuse of recycled aggregates obtained by crushing the old concrete roads as a building material in the new top layers of concrete pavements. The paper is based on gathering the current knowledge about how to use recycled concrete aggregate, suitability, and modification of the properties and its standa...

  1. Highly efficient photocatalytic conversion of solar energy to hydrogen by WO3/BiVO4 core-shell heterojunction nanorods

    Science.gov (United States)

    Kosar, Sonya; Pihosh, Yuriy; Bekarevich, Raman; Mitsuishi, Kazutaka; Mawatari, Kazuma; Kazoe, Yutaka; Kitamori, Takehiko; Tosa, Masahiro; Tarasov, Alexey B.; Goodilin, Eugene A.; Struk, Yaroslav M.; Kondo, Michio; Turkevych, Ivan

    2018-04-01

    Photocatalytic splitting of water under solar light has proved itself to be a promising approach toward the utilization of solar energy and the generation of environmentally friendly fuel in a form of hydrogen. In this work, we demonstrate highly efficient solar-to-hydrogen conversion efficiency of 7.7% by photovoltaic-photoelectrochemical (PV-PEC) device based on hybrid MAPbI3 perovskite PV cell and WO3/BiVO4 core-shell nanorods PEC cell tandem that utilizes spectral splitting approach. Although BiVO4 is characterized by intrinsically high recombination rate of photogenerated carriers, this is not an issue for WO3/BiVO4 core-shell nanorods, where highly conductive WO3 cores are combined with extremely thin absorber BiVO4 shell layer. Since the BiVO4 layer is thinner than the characteristic carrier diffusion length, the photogenerated charge carriers are separated at the WO3/BiVO4 heterojunction before their recombination. Also, such architecture provides sufficient optical thickness even for extremely thin BiVO4 layer due to efficient light trapping in the core-shell WO3/BiVO4 nanorods with high aspect ratio. We also demonstrate that the concept of fill factor can be used to compare I-V characteristics of different photoanodes regarding their optimization for PV/PEC tandem devices.

  2. Mesoporous WN/WO3-Composite Nanosheets for the Chemiresistive Detection of NO2 at Room Temperature

    OpenAIRE

    Fengdong Qu; Bo He; Rohiverth Guarecuco; Minghui Yang

    2016-01-01

    Composite materials, which can optimally use the advantages of different materials, have been studied extensively. Herein, hybrid tungsten nitride and oxide (WN/WO3) composites were prepared through a simple aqueous solution route followed by nitriding in NH3, for application as novel sensing materials. We found that the introduction of WN can improve the electrical properties of the composites, thus improving the gas sensing properties of the composites when compared with bare WO3. The highe...

  3. Use of fiber reinforced concrete for concrete pavement slab replacement.

    Science.gov (United States)

    2014-03-01

    Unlike ordinary concrete pavement, replacement concrete slabs need to be open to traffic within 24 hours (sooner in : some cases). Thus, high early-strength concrete is used; however, it frequently cracks prematurely as a result of high : heat of hyd...

  4. Highly Yb-doped KGd(WO4)2 thin-film amplifier

    NARCIS (Netherlands)

    Yong, Yean Sheng; Aravazhi, S.; Vázquez-Córdova, Sergio Andrés; García Blanco, Sonia Maria; Pollnau, Markus

    We report record-high small-signal gain of 1050 dB/cm at 981 nm wavelength in a KGd0.425Yb0.575(WO4)2 thin film. The sensitivity of gain to the shift of beam-focus position, which is critical under non-waveguiding conditions, is investigated.

  5. Polar and Magnetic Layered A Site and Rock Salt B Site-Ordered NaLnFeWO6 (Ln = La, Nd) Perovskites

    Energy Technology Data Exchange (ETDEWEB)

    Tetuerto, Maria [State University of New Jersey, The; Li, Mang-Rong [State University of New Jersey, The; Ignatov, Alexander [State University of New Jersey, The; Croft, Mark [State University of New Jersey, The; Ramanujachary, Kandalam V. [Rowan University; Chi, Songxue [ORNL; Hodges, Jason P [ORNL; Dachraoui, W. [University of Antwerp; Hadermann, Joke [University of Antwerp; Thao Tran, T. [University of Houston, Houston; Shiv Halasyamani, P. [University of Houston, Houston; Grams, C. [Universitat zu Koln, Koln, Germany; Hemberger, J. [Universitat zu Koln, Koln, Germany; Greenblatt, M. [State University of New Jersey, The

    2013-01-01

    We have expanded the double perovskite family of materials with the unusual combination of layered order in the A sublattice and rock salt order over the B sublattice to compounds NaLaFeWO6 and NaNdFeWO6. The materials have been synthesized and studied by powder X-ray diffraction, neutron diffraction, electron diffraction, magnetic measurements, X-ray absorption spectroscopy, dielectric measurements, and second harmonic generation. At room temperature, the crystal structures of both compounds can be defined in the noncentrosymmetric monoclinic P21 space group resulting from the combination of ordering both in the A and B sublattices, the distortion of the cell due to tilting of the octahedra, and the displacement of certain cations. The magnetic studies show that both compounds are ordered antiferromagnetically below TN 25 K for NaLaFeWO6 and at 21 K for NaNdFeWO6. The magnetic structure of NaNdFeWO6 has been solved with a propagation vector k = (1/2 0 1/2) as an antiferromagnetic arrangement of Fe and Nd moments. Although the samples are potential multiferroics, the dielectric measurements do not show a ferroelectric response.

  6. A multifunctional design approach for sustainable concrete : with application to concrete mass products

    NARCIS (Netherlands)

    Hüsken, G.

    2010-01-01

    This thesis provides a multifunctional design approach for sustainable concrete, particularly earth-moist concrete (EMC), with application to concrete mass products. EMC is a concrete with low water content and stiff consistency that is used for the production of concrete mass products, such as

  7. Solar light-facilitated oxytetracycline removal from the aqueous phase utilizing a H2O2/ZnWO4/CaO catalytic system

    Directory of Open Access Journals (Sweden)

    Pankaj Raizada

    2017-09-01

    Full Text Available A CaO-supported ZnWO4 nanocomposite (ZnWO4/CaO was successfully synthesized using a novel hydrothermal method and was characterized by scanning electron microscopy (SEM, tunnelling electron microscopy (TEM, X-ray diffraction (XRD, electron diffraction X-ray (EDX, Fourier transform infrared spectroscopy (FTIR and UV–visible (UV–vis spectral analysis. The ZnWO4/CaO composites exhibited rod-like morphologies with variable lengths from 45 nm to 147 nm and diameters from 26 nm to 36 nm. The catalytic efficiency of the synthesized ZnWO4/CaO composites was displayed for the photodegradation of oxytetracycline (OTC antibiotic from the aqueous phase. The synergistic degradation of OTC was investigated in the presence of H2O2 and ZnWO4/CaO. The rate of photodegradation followed pseudo-first-order kinetics. The antibiotic removal was strongly influenced by the catalyst loading, H2O2 concentration, pH and OTC concentration. Using a solar/H2O2/ZnWO4/CaO catalytic system, 85% COD removal was attained for OTC degradation in 210 min. The oxidative degradation occurred through hydroxyl radicals. The prepared nanocomposites possessed high recyclability and were easily separated from the aqueous solution by a simple sedimentation process.

  8. Time decay and photoluminescence measurement of PbWO4 crystal

    International Nuclear Information System (INIS)

    Baylac, M.

    1997-09-01

    This report presented the experimental characterization of the PbWO 4 crystals that we will be used for the photon detector of the Compton polarimeter at the Jefferson laboratory. We could draw 3 main features from this study. The transmission rate of the crystals is about 60 % in the scintillation wavelength region. From the decay time analysis, we deduced 3 decay components of the PbWO 4 , predicted by other measurements: τ 1 ∼5 ns, τ 2 ∼20 ns, τ 3 ∼100 ns, taking respectively 26 %, 30 % and 4 % of the total light amplitude emitted by the crystals. Moreover, we showed the existence of a fourth decay constant (τ 4 ∼1μs) taking 40 % of the total quantity of light which is responsible for the bad precision on the third constant determination. We could not characterize this component accurately because of the limited time range of the recordings. To improve the determination of the super-slow component, we need to perform the measurements again on a longer time scale, on the order of a few microseconds. We eventually measured the light yield of the PbWO 4 crystals. With a first analysis, we found about 3.5 photoelectrons per MeV whereas the constructors note gave about 10. We then reduced the light loss in the experimental set up by wrapping the last open end of the crystal. The results were slightly improved. Eventually, we increased the recording time, to take account the super-low decay, and found that the crystals yield about 6 photoelectrons per MeV which is still less than predicted. (author)

  9. Facile preparation of Z-scheme WO{sub 3}/g-C{sub 3}N{sub 4} composite photocatalyst with enhanced photocatalytic performance under visible light

    Energy Technology Data Exchange (ETDEWEB)

    Cui, Lifeng, E-mail: lifeng.cui@gmail.com [School of Chemistry and Environmental Engineering, Dongguan University of Technology, Guangdong 523808 (China); Ding, Xiang; Wang, Yangang; Shi, Huancong; Huang, Lihua; Zuo, Yuanhui [Department of Environmental Science and Engineering, University of Shanghai for Science and Technology, Shanghai 200093 (China); Kang, Shifei, E-mail: sfkang@usst.edu.cn [Department of Environmental Science and Engineering, University of Shanghai for Science and Technology, Shanghai 200093 (China)

    2017-01-01

    Highlights: • WO{sub 3}/g-C{sub 3}N{sub 4} composites were synthesized through a facile mixing-and-heating method. • The composite showed improved visible light response. • The composite showed high activity for MB degradation. • Z-scheme charge carrier transfer pathways in the composite are proposed. - Abstract: Visible-light-driven WO{sub 3}/g-C{sub 3}N{sub 4} composites photocatalysts were synthesized via a facile one-step simultaneously heating procedure with urea as the main precursor. These prepared catalyst samples were characterized by X-ray diffraction (XRD), thermogravimetric analysis (TG), transmission electron microscopy (TEM), N{sub 2} adsorption, ultraviolet-visible diffuse reflection spectroscopy (UV–vis), X-ray photoelectron spectroscopy (XPS), photoluminescence (PL) and electrochemical impedance spectroscopy (EIS). The photocatalytic activity of the WO{sub 3}/g-C{sub 3}N{sub 4} composites was evaluated by the photo-degradation of Rhodamine B (RhB) under visible light irradiation. The results indicated that the composites with 25 wt.% WO{sub 3} content exhibited highest photocatalytic activity compared to pure WO{sub 3}, bare g-C{sub 3}N{sub 4} and other WO{sub 3}/g-C{sub 3}N{sub 4} composites. The favorable photocatalytic activity of WO{sub 3}/g-C{sub 3}N{sub 4} composites was mainly attributed to the excellent surface properties, enhanced visible-light absorption and the desirable band positions. A possible Z-scheme photocatalytic mechanism was proposed based on structure and electrochemical characterizations results, which can well explain the enhanced migration rate of photogenerated electrons and holes in WO{sub 3}/g-C{sub 3}N{sub 4} heterojunctions.

  10. The influence of recycled concrete aggregates in pervious concrete

    Directory of Open Access Journals (Sweden)

    L. M. TAVARES

    Full Text Available The expansion of urban areas under constant changes in the hydrological cycle directly affects the drainage of rainwater. The problems of urban drainage become major engineering problems to be solved in order to avoid negative consequences for local populations. Another urban problem is the excessive production of construction and demolition waste (CDW, in which , even with a increasingly policy of waste management , have been an end up being thrown in inappropriate disposal sites. Alternatively aiming to a minimization of the problems presented, we propose the study of permeable concrete using recycled concrete aggregate. In this study, there were evaluated the performance of concrete by means of permeability, consistency, strength, and interface conditions of the materials . Satisfactory relationships of resistance/permeability of concrete with recycled aggregate in relation to the concrete with natural aggregates was obtained, showing their best potential.

  11. Ag2WO4 nanorods decorated with AgI nanoparticles: Novel and efficient visible-light-driven photocatalysts for the degradation of water pollutants

    Directory of Open Access Journals (Sweden)

    Shijie Li

    2018-04-01

    Full Text Available To develop efficient and stable visible-light-driven (VLD photocatalysts for pollutant degradation, we synthesized novel heterojunction photocatalysts comprised of AgI nanoparticle-decorated Ag2WO4 nanorods via a facile method. Various characterization techniques, including XRD, SEM, TEM, EDX, and UV–vis DRS were used to investigate the morphology and optical properties of the as-prepared AgI/Ag2WO4 catalyst. With AgI acting as the cocatalyst, the resulting AgI/Ag2WO4 heterostructure shows excellent performance in degrading toxic, stable pollutants such as rhodamine B (RhB, methyl orange (MO and para-chlorophenol (4-CP. The high performance is attributed to the enhanced visible-light absorption properties and the promoted separation efficiency of charge carriers through the formation of the heterojunction between AgI and Ag2WO4. Additionally, AgI/Ag2WO4 exhibits durable stability. The active species trapping experiment reveals that active species (O2•− and h+ dominantly contribute to RhB degradation. The AgI/Ag2WO4 heterojunction photocatalyst characterized in this work holds great potential for remedying environmental issues due to its simple preparation method and excellent photocatalytic performance.

  12. Critical difference between optoelectronic properties of α- and β-SnWO4semiconductors: A DFT/HSE06 and experimental investigation

    KAUST Repository

    Harb, Moussab

    2016-02-03

    The optoelectronic properties of β-SnWO4 are investigated in details using experiments on thin film generated by rapid quenching and the first-principles quantum calculations based on the density functional theory (DFT, including the perturbation approach DFPT) and employing the PBE and the range-separated hybrid exchange-correlation HSE06 functionals. The obtained bandgap, optical absorption coefficient, dielectric constant, and charge-carrier effective masses for β-SnWO4 exhibit data irreconcilable with the reported values: e.g., a large and direct bandgap of 4.30eV (UV-responsive), inconsistent with the values in the literature (visible-responsive). These properties obtained for β-SnWO4 are distinctive from those for α-SnWO4: an indirect bandgap of 1.52eV with higher charge mobilities. These data of intrinsic stoichiometric materials suggest that the literature reported nonstoichiometric materials where defects significantly influence the optoelectronic properties. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  13. Influence of Concrete Properties on Molten Core-Concrete Interaction: A Simulation Study

    Directory of Open Access Journals (Sweden)

    Jin-yang Jiang

    2016-01-01

    Full Text Available In a severe nuclear power plant accident, the molten core can be released into the reactor pit and interact with sacrificial concrete. In this paper, a simulation study is presented that aims to address the influence of sacrificial concrete properties on molten core-concrete interaction (MCCI. In particular, based on the MELCOR Code, the ferrosiliceous concrete used in European Pressurized Water Reactor (EPR is taken into account with respect to the different ablation enthalpy and Fe2O3 and H2O contents. Results indicate that the concrete ablation rate as well as the hydrogen generation rate depends much on the concrete ablation enthalpy and Fe2O3 and H2O contents. In practice, the ablation enthalpy of sacrificial concrete is the higher the better, while the Fe2O3 and H2O content of sacrificial concrete is the lower the better.

  14. World Register of marine Cave Species (WoRCS: a new Thematic Species Database for marine and anchialine cave biodiversity

    Directory of Open Access Journals (Sweden)

    Vasilis Gerovasileiou

    2016-09-01

    Full Text Available Scientific exploration of marine cave environments and anchialine ecosystems over recent decades has led to outstanding discoveries of novel taxa, increasing our knowledge of biodiversity. However, biological research on underwater caves has taken place only in a few areas of the world and relevant information remains fragmented in isolated publications and databases. This fragmentation makes assessing the conservation status of marine cave species especially problematic, and this issue should be addressed urgently given the stresses resulting from planned and rampant development in the coastal zone worldwide. The goal of the World Register of marine Cave Species (WoRCS initiative is to create a comprehensive taxonomic and ecological database of known species from marine caves and anchialine systems worldwide and to present this as a Thematic Species Database (TSD of the World Register of marine Species (WoRMS. WoRCS will incorporate ecological data (e.g., type of environment, salinity regimes, and cave zone as well as geographical information on the distribution of species in cave and anchialine environments. Biodiversity data will be progressively assembled from individual database sources at regional, national or local levels, as well as from literature sources (estimate: >20,000 existing records of cave-dwelling species scattered in several databases. Information will be organized in the WoRCS database following a standard glossary based on existing terminology. Cave-related information will be managed by the WoRCS thematic editors with all data dynamically linked to WoRMS and its team of taxonomic editors. In order to mobilize data into global biogeographic databases, a Gazetteer of the Marine and Anchialine Caves of the World will be established. The presence records of species could be eventually georeferenced for submission to the Ocean Biogeographic Information System (OBIS and constitute an important dataset for biogeographical and

  15. Thermal oxidation of seeds for the hydrothermal growth of WO{sub 3} nanorods on ITO glass substrate

    Energy Technology Data Exchange (ETDEWEB)

    Ng, Chai Yan [School of Materials and Mineral Resources Engineering, Universiti Sains Malaysia, 14300 Nibong Tebal, Penang (Malaysia); Department of Mechanical and Material Engineering, Lee Kong Chian Faculty of Engineering and Science, Universiti Tunku Abdul Rahman, Jalan Sungai Long, Bandar Sungai Long, Cheras, 43000 Kajang, Selangor (Malaysia); Abdul Razak, Khairunisak, E-mail: khairunisak@usm.my [School of Materials and Mineral Resources Engineering, Universiti Sains Malaysia, 14300 Nibong Tebal, Penang (Malaysia); NanoBiotechnology Research and Innovation (NanoBRI), Institute for Research in Molecular Medicine (INFORMM), Universiti Sains Malaysia, 11800 USM, Penang (Malaysia); Lockman, Zainovia, E-mail: zainovia@usm.my [School of Materials and Mineral Resources Engineering, Universiti Sains Malaysia, 14300 Nibong Tebal, Penang (Malaysia)

    2015-11-30

    This work reports a simple seed formation method for the hydrothermal growth of tungsten oxide (WO{sub 3}) nanorods. A WO{sub 3} seed layer was prepared by thermal oxidation, where a W-sputtered substrate was heated and oxidized in a furnace. Oxidation temperatures and periods were varied at 400–550 °C and 5–60 min, respectively, to determine an appropriate seed layer for nanorod growth. Thermal oxidation at 500 °C for 15 min was found to produce a seed layer with sufficient crystallinity and good adhesion to the substrate. These properties prevented the seed from peeling off during the hydrothermal process, thereby allowing nanorod growth on the seed. The nanorod film showed better electrochromic behavior (higher current density of − 1.11 and + 0.65 mA cm{sup −2}) than compact film (lower current density of − 0.54 and + 0.28 mA cm{sup −2}). - Highlights: • A simple seed formation method (thermal oxidation) on sputtered W film is reported. • Crystalline seed with good adhesion to substrate is required for nanorod growth. • The appropriate temperature and period for seed formation were 500 °C and 15 min. • WO{sub 3} nanorods exhibited higher electrochromic current density than WO{sub 3} compact film.

  16. Microwave assisted hydrothermal synthesis of Ag/AgCl/WO3 photocatalyst and its photocatalytic activity under simulated solar light

    International Nuclear Information System (INIS)

    Adhikari, Rajesh; Gyawali, Gobinda; Sekino, Tohru; Wohn Lee, Soo

    2013-01-01

    Simulated solar light responsive Ag/AgCl/WO 3 composite photocatalyst was synthesized by microwave assisted hydrothermal process. The synthesized powders were characterized by X-Ray Diffraction (XRD) spectroscopy, X-Ray Photoelectron Spectroscopy (XPS), Transmission Electron Microscopy (TEM), Diffuse Reflectance Spectroscopy (UV–Vis DRS), and BET surface area analyzer to investigate the crystal structure, morphology, chemical composition, optical properties and surface area of the composite photocatalyst. This photocatalyst exhibited higher photocatalytic activity for the degradation of rhodamine B under simulated solar light irradiation. Dye degradation efficiency of composite photocatalyst was found to be increased significantly as compared to that of the commercial WO 3 nanopowder. Increase in photocatalytic activity of the photocatalyst was explained on the basis of surface plasmon resonance (SPR) effect caused by the silver nanoparticles present in the composite photocatalyst. Highlights: ► Successful synthesis of Ag/AgCl/WO 3 nanocomposite. ► Photocatalytic experiment was performed under simulated solar light. ► Nanocomposite photocatalyst was very active as compared to WO 3 commercial powder. ► SPR effect due to Ag nanoparticles enhanced the photocatalytic activity.

  17. Bi3+ sensitized Y2WO6:Ln3+ (Ln=Dy, Eu, and Sm) phosphors for solar spectral conversion.

    Science.gov (United States)

    Huang, M N; Ma, Y Y; Xiao, F; Zhang, Q Y

    2014-01-01

    The phosphors of Y2WO6:Bi3+, Ln3+ (Ln=Dy, Eu and Sm) were synthesized by solid-state reaction in this study. The crystal structure, photoluminescence properties and energy transfer mechanism were investigated. By introducing Bi3+ ions, the excitation band of the phosphors was broadened to be 250-380 nm, which could be absorbed by the dye-sensitized solar cells (DSSCs). The overlap between excitation of W-O groups/Bi3+ and the emission of Ln3+ (Dy, Eu, and Sm) indicated that the probability of energy transfer from W-O groups and Bi3+ to Ln3+. The energy transfer efficiency from Bi3+ to Ln3+ (Ln=Dy, Eu and Sm) are calculated to be 16%, 20% and 58%. This work suggested that Y2WO6:Bi3+, Ln3+ (Ln=Dy, Eu and Sm) might be a promising ultraviolet-absorbing luminescent converter to enhance the photoelectrical conversion efficiency of dye-sensitized solar cells (DSSCs). Copyright © 2013 Elsevier B.V. All rights reserved.

  18. Gas Sensor Based on 3-D WO3 Inverse Opal: Design and Applications

    Directory of Open Access Journals (Sweden)

    Ruiqing Xing

    2017-03-01

    Full Text Available A three-dimensional inverse opal (3DIO WO3 architecture has been synthesized via a simple sacrificial template method. Morphology features of the 3DIO were characterized by scanning electron microscope (SEM and its structure was characterized by X-ray diffraction (XRD. The shrinking ratio of the PMMA spheres was ~28.2% through measuring the distribution of the PMMA spheres and 3DIO WO3 center-to-center distance between the spheres and macropores, respectively. Beyond that, the 3DIO gas sensing properties were investigated systematically and the sensing mechanism of 3DIO WO3 was proposed. The results indicated that the response of the 3DIO sensor possessed excellent sensitivity to acetone gas, especially at trace levels. The 3DIO gas sensor response was ~7 to 5 ppm of acetone and could detect acetone low to 0.2 ppm effectively, which was in close proximity to the theoretical low detection limit of 0.14 ppm when Ra/Rg ≥ 1.2 was used as the criterion for reliable gas sensing. All in all, the obvious satisfaction of the gas-sensing properties was ascribed to the structure of the 3DIO, and the sensor could be a promising novel device in the future.

  19. Understanding the conductive channel evolution in Na:WO(3-x)-based planar devices.

    Science.gov (United States)

    Shang, Dashan; Li, Peining; Wang, Tao; Carria, Egidio; Sun, Jirong; Shen, Baogen; Taubner, Thomas; Valov, Ilia; Waser, Rainer; Wuttig, Matthias

    2015-04-14

    An ion migration process in a solid electrolyte is important for ion-based functional devices, such as fuel cells, batteries, electrochromics, gas sensors, and resistive switching systems. In this study, a planar sandwich structure is prepared by depositing tungsten oxide (WO(3-x)) films on a soda-lime glass substrate, from which Na(+) diffuses into the WO(3-x) films during the deposition. The entire process of Na(+) migration driven by an alternating electric field is visualized in the Na-doped WO(3-x) films in the form of conductive channel by in situ optical imaging combined with infrared spectroscopy and near-field imaging techniques. A reversible change of geometry between a parabolic and a bar channel is observed with the resistance change of the devices. The peculiar channel evolution is interpreted by a thermal-stress-induced mechanical deformation of the films and an asymmetric Na(+) mobility between the parabolic and the bar channels. These results exemplify a typical ion migration process driven by an alternating electric field in a solid electrolyte with a low ion mobility and are expected to be beneficial to improve the controllability of the ion migration in ion-based functional devices, such as resistive switching devices.

  20. Review of concrete properties for prestressed concrete pressure vesssels

    International Nuclear Information System (INIS)

    Nanstad, R.K.

    1976-10-01

    The desire for increasing power output along with safety requirements has resulted in consideration of the prestressed concrete pressure vessel (PCPV) for most current nuclear reactor systems, as well as for the very-high-temperature reactor for process heat and as primary pressure vessels for coal conversion systems. Results are presented of a literature review to ascertain current knowledge regarding plain concrete properties under conditions imposed by a mass concrete structure such as PCRV. The effects of high temperature on such properties as strength, elasticity, and creep are discussed, as well as changes in thermal properties, multiaxial behavior, and the mechanisms thought to be responsible for the observed behavior. In addition, the effects of radiation and moisture migration are discussed. It is concluded that testing results found in the technical literature show much disagreement as to the effects of temperature on concrete properties. The variations in concrete mixtures, curing and testing procedures, age at loading, and moisture conditions during exposure and testing are some of the reasons for such disagreement. Test results must be limited, in most cases, to the materials and conditions of a given test rather than applied to such a general class of materials such as concrete. It is also concluded that sustained exposure of normal concretes to current PCRV operating conditions will not result in any significant loss of properties. However, lack of knowledge regarding effects of temperatures exceeding 100 0 C (212 0 F), moisture migration, and multiaxial behavior precludes a statement advocating operation beyond current design limits. The report includes recommendations for future research on concrete for PCPVs

  1. Development of highly workable concrete, 'Neuro-crete'. Part 1. ; Basic properties of Neuro-crete and application to large-scale structures with heavy-reinforcement. Koryudo concrete (Neuro crete) no kaihatsu. 1. ; Neuro crete no kiso bussei to kamitsu haikin wo yusuru doboku kozobutsu eno tekiyo

    Energy Technology Data Exchange (ETDEWEB)

    Miura, N; Chikamatsu, R; Sogo, S; Haga, T; Iriya, K; Taniguchi, M [Obayashi Corp., Tokyo (Japan)

    1993-08-10

    This paper introduces a highly workable concrete, 'Neuro-crete' developed for the purpose of simplifying construction of concrete structures and improving their guality. This concrete has a feature that it can reduce or eliminate a compacting process. Resistance to separation of coarse aggregate from mortar (separation resistance) is required. A difference of the material from conventional concrete is an increased unit particulate amount (binder + inert particulate). The binders may include cement, blast furnace slag particulate, flyash, silica fume, and expander. The inert particulate may be limestone powder. Kinds and mixing ratio of binders are important in improving fluidity. The separation resistivity is largely affected by a water-cement ratio and a water-binder ratio. A flow distance limit exists to maintain the fluidity without decreasing the compression strength after curing. The internal structure having become denser suppresses progress of neutralization or salt penetration. Drying contraction is equivalent to or less than the conventional concrete. 5 refs., 30 figs., 3 tabs.

  2. Quantum dots as mediators in gas sensing: A case study of CdS sensitized WO{sub 3} sensing composites

    Energy Technology Data Exchange (ETDEWEB)

    Concina, Isabella, E-mail: concina@sensor.ing.unibs.it [CNR-INO SENSOR Laboratory, via Branze, 45, 25131 Brescia (Italy); SENSOR, Department of Information Engineering, Brescia University, via Valotti, 9, 25133 Brescia (Italy); Comini, Elisabetta [CNR-INO SENSOR Laboratory, via Branze, 45, 25131 Brescia (Italy); SENSOR, Department of Information Engineering, Brescia University, via Valotti, 9, 25133 Brescia (Italy); Kaciulis, Saulius [CNR-ISMN, Institute for the Study of Nanostructured Materials, Via dei Taurini, 19, 00185 Roma (Italy); Sberveglieri, Giorgio [CNR-INO SENSOR Laboratory, via Branze, 45, 25131 Brescia (Italy); SENSOR, Department of Information Engineering, Brescia University, via Valotti, 9, 25133 Brescia (Italy)

    2014-01-30

    In this study the proof of principle of the use of naked semiconductor directly generated on metal oxide surface as mediators in gas sensing is provided. Successive ionic layer absorption and reaction (SILAR) technique has been applied to sensitize a WO{sub 3} thin film with CdS quantum dots. Response to gases of bare WO{sub 3} is deeply modified: quantum dots dramatically increase the metal oxide conductance, otherwise rather poor, and modify the capability of detecting environmental pollutants, such as CO and NO{sub 2}. A modified sensing mechanism is proposed to rationalize the mediation exerted by the semiconducting active layer on the interaction between gaseous species and WO{sub 3} surface.

  3. Production of ultrafine particles of high-temperature tetragonal WO3 by dc arc discharge in Ar-O2 gases

    International Nuclear Information System (INIS)

    Guo Yumei; Murata, Norihiko; Ono, Kazuya; Okazaki, Tsugio

    2005-01-01

    Ultrafine particles of WO 3 are successfully produced by dc arc discharge in Ar-O 2 gases. Particle sizes are distributed from 10 nm to 1 μm depending on production conditions: gas pressure, collection position and discharge current. Observations of the cooled particles by electron microscopy indicate that the WO 3 particles are tetragonal, a phase that is usually only stable above 725 deg. C. The octahedral crystals are bounded by eight {1 0 1} faces and occasionally truncated by {1 0 0} and/or {0 0 1} faces. This method of producing WO 3 by dc arc discharge therefore affords a high-temperature phase that is preserved upon cooling to room temperature

  4. Construction of an all-solid-state artificial Z-scheme system consisting of Bi2WO6/Au/CdS nanostructure for photocatalytic CO2 reduction into renewable hydrocarbon fuel

    Science.gov (United States)

    Wang, Meng; Han, Qiutong; Li, Liang; Tang, Lanqin; Li, Haijin; Zhou, Yong; Zou, Zhigang

    2017-07-01

    An all-solid-state Bi2WO6/Au/CdS Z-scheme system was constructed for the photocatalytic reduction of CO2 into methane in the presence of water vapor. This Z-scheme consists of ultrathin Bi2WO6 nanoplates and CdS nanoparticles as photocatalysts, and a Au nanoparticle as a solid electron mediator offering a high speed charge transfer channel and leading to more efficient spatial separation of electron-hole pairs. The photo-generated electrons from the conduction band (CB) of Bi2WO6 transfer to the Au, and then release to the valence band (VB) of CdS to recombine with the holes of CdS. It allows the electrons remaining in the CB of CdS and holes in the VB of Bi2WO6 to possess strong reduction and oxidation powers, respectively, leading the Bi2WO6/Au/CdS to exhibit high photocatalytic reduction of CO2, relative to bare Bi2WO6, Bi2WO6/Au, and Bi2WO6/CdS. The depressed hole density on CdS also enhances the stability of the CdS against photocorrosion.

  5. Ambient template synthesis of multiferroic MnWO4 nanowires and nanowire arrays

    International Nuclear Information System (INIS)

    Zhou Hongjun; Yiu Yuen; Aronson, M.C.; Wong, Stanislaus S.

    2008-01-01

    The current report describes the systematic synthesis of polycrystalline, multiferroic MnWO 4 nanowires and nanowire arrays with controllable chemical composition and morphology, using a modified template-directed methodology under ambient room-temperature conditions. We were able to synthesize nanowires measuring 55±10, 100±20, and 260±40 nm in diameter, respectively, with lengths ranging in the microns. Extensive characterization of as-prepared samples has been performed using X-ray diffraction, scanning electron microscopy, transmission electron microscopy (TEM), high-resolution TEM, and energy-dispersive X-ray spectroscopy. Magnetic behavior in these systems was also probed. - Graphical abstract: Systematic synthesis of crystalline, multiferroic MnWO4 nanowires and nanowire arrays with controllable chemical composition and morphology, using a modified template-directed methodology under ambient room-temperature conditions

  6. Investigation of the La2O3-Nb2O5-WO3 ternary phase diagram: Isolation and crystal structure determination of the original La3NbWO10 material

    KAUST Repository

    Vu, T.D.

    2015-05-23

    In the course of the exploration of the La2O3-WO3-Nb2O5 ternary phase diagram, a new compound with the formula La3NbWO10 was discovered. Its structure was determined from a combination of powder X-ray and neutron diffraction data. It crystallizes in the tetragonal space group P42/nmc (no. 137) with the lattice parameters: a=10.0807(1) Å; c=12.5540(1) Å. The structure is built up from infinite ribbons of octahedra (W/Nb)O5 which are perpendicular to each other, lanthanum ions being distributed around these ribbons. The electrical properties of this compound were investigated on sintered pellets by means of complex impedance spectroscopy. © 2015 Elsevier Inc. All rights reserved.

  7. Subsolidus phase relations of the SrO–WO3–CuO system at 800 °C in air

    DEFF Research Database (Denmark)

    Grivel, Jean-Claude; Norby, Poul

    2012-01-01

    The subsolidus phase relations of the SrO–WO3–CuO system were investigated in air. The samples were equilibrated at 800 °C. Under these conditions, eight binary oxides are stable. The pseudo-ternary section contains two ternary oxide phases: the previously described Sr2CuWO6 phase as well as a new...

  8. Low-temperature liquid-phase epitaxy and optical waveguiding of rare-earth-ion-doped KY(WO4)2 thin layers

    NARCIS (Netherlands)

    Romanyuk, Y.E.; Utke, I.; Ehrentraut, D.; Apostolopoulos, V.; Pollnau, Markus; Garcia-Revilla, S.; Valiente, B.

    2004-01-01

    Crystalline $KY(WO_{4})_{2}$ thin layers doped with different rare-earth ions were grown on b-oriented, undoped $KY(WO_{4})_{2}$ substrates by liquid-phase epitaxy employing a low-temperature flux. The ternary chloride mixture of NaCl, KCl, and CsCl with a melting point of 480°C was used as a

  9. Investigation of Electrical, Optical and GaS Sensing properties Sol-Gel Derived WO3 Thin Films

    International Nuclear Information System (INIS)

    Dumludag, F.

    2008-01-01

    Tungsten oxide (WO 3 ) is a wide band gap n-type semiconductor. Thin films of WO 3 are considerable interest because of their potential applications in electrochromic devices, and gas sensors. In this work, WO 3 thin films were deposited on IDT (Interdigital electrodes) by a sol-gel dipping process. Precursor solution was prepared by dissolving of tungstic acid in ammonia. We investigated d.c. and a.c. (40 Hz-100 KHz) electrical properties of the films in the temperature range of 293K and 473K in vacuum ambient (10 - 2 mbar). We observed frequency dependent conductivity behavior at high frequencies. Absorption spectra of the film showed that a maximum absorption occurred at 330 nm. We also investigated the response of the films to vapors of the volatile organic compounds (acetone, chloroform, toluene, ethanol, ammonia) and water vapor. The films showed no sensitivity to the test gases at room temperature. Concentration of the vapors were controlled by mass flowmeters. All the measurement system was computerized

  10. Reinforced sulphur concrete

    NARCIS (Netherlands)

    2014-01-01

    Reinforced sulphur concrete wherein one or more metal reinforcing members are in contact with sulphur concrete is disclosed. The reinforced sulphur concrete comprises an adhesion promoter that enhances the interaction between the sulphur and the one or more metal reinforcing members.

  11. High-energy lithium-ion hybrid supercapacitors composed of hierarchical urchin-like WO3/C anodes and MOF-derived polyhedral hollow carbon cathodes.

    Science.gov (United States)

    Xu, Juan; Li, Yuanyuan; Wang, Lei; Cai, Qifa; Li, Qingwei; Gao, Biao; Zhang, Xuming; Huo, Kaifu; Chu, Paul K

    2016-09-22

    A lithium-ion hybrid supercapacitor (Li-HSC) comprising a Li-ion battery type anode and an electrochemical double layer capacitance (EDLC) type cathode has attracted much interest because it accomplishes a large energy density without compromising the power density. In this work, hierarchical carbon coated WO 3 (WO 3 /C) with a unique mesoporous structure and metal-organic framework derived nitrogen-doped carbon hollow polyhedra (MOF-NC) are prepared and adopted as the anode and the cathode for Li-HSCs. The hierarchical mesoporous WO 3 /C microspheres assembled by radially oriented WO 3 /C nanorods along the (001) plane enable effective Li + insertion, thus exhibit high capacity, excellent rate performance and a long cycling life due to their high Li + conductivity, electronic conductivity and structural robustness. The WO 3 /C structure shows a reversible specific capacity of 508 mA h g -1 at a 0.1 C rate (1 C = 696 mA h g -1 ) after 160 discharging-charging cycles with excellent rate capability. The MOF-NC achieved the specific capacity of 269.9 F g -1 at a current density of 0.2 A g -1 . At a high current density of 6 A g -1 , 92.4% of the initial capacity could be retained after 2000 discharging-charging cycles, suggesting excellent cycle stability. The Li-HSC comprising a WO 3 /C anode and a MOF-NC cathode boasts a large energy density of 159.97 W h kg -1 at a power density of 173.6 W kg -1 and 88.3% of the capacity is retained at a current density of 5 A g -1 after 3000 charging-discharging cycles, which are better than those previously reported for Li-HSCs. The high energy and power densities of the Li-HSCs of WO 3 /C//MOF-NC render large potential in energy storage.

  12. Ease synthesis of mesoporous WO{sub 3}–TiO{sub 2} nanocomposites with enhanced photocatalytic performance for photodegradation of herbicide imazapyr under visible light and UV illumination

    Energy Technology Data Exchange (ETDEWEB)

    Ismail, Adel A., E-mail: adelali141@yahoo.com [Advanced Materials Department, Central Metallurgical R& D Institute, CMRDI, P.O. Box 87, Helwan 11421 Cairo (Egypt); Advanced Materials and Nano Research Center, Najran University, P.O. Box 1988, Najran 11001 (Saudi Arabia); Abdelfattah, Ibrahim [Water Pollution Research Dept., National Research Centre, 33 EL Bohouth St. (Former EL Tahrir St.), P.O. 12622, Dokki, Giza (Egypt); Helal, Ahmed [Advanced Materials Department, Central Metallurgical R& D Institute, CMRDI, P.O. Box 87, Helwan 11421 Cairo (Egypt); Al-Sayari, S.A. [Advanced Materials and Nano Research Center, Najran University, P.O. Box 1988, Najran 11001 (Saudi Arabia); Robben, L. [Chemische Kristallographie fester Stoffe, Universität Bremen (Germany); Bahnemann, D.W. [Institut für Technische Chemie, Leibniz Universität Hannover, Callinstrasse 3, 30167 Hannover (Germany)

    2016-04-15

    Highlights: • Ease synthesis of mesoporous WO{sub 3}–TiO{sub 2} nanocomposites were performed. • XRD and Raman spectra confirmed that monoclinic and triclinic of WO{sub 3} was detected. • The prepared photocatalysts were evaluated for photodegradation of imazapyr. • It could be completely degraded of imazapyr within 120 min under UV light. • Under visible light, 0.5%WO{sub 3}–TiO{sub 2} is the optimum with 46% photocatalytic efficiency. - Abstract: Herein, we report the ease synthesis of mesoporous WO{sub 3}–TiO{sub 2} nanocomposites at different WO{sub 3} contents (0–5 wt%) together with their photocatalytic performance for the degradation of the imazapyr herbicide under visible light and UV illumination. XRD and Raman spectra indicated that the highly crystalline anatase TiO{sub 2} phase and monoclinic and triclinic of WO{sub 3} were formed. The mesoporous TiO{sub 2} exhibits large pore volumes of 0.267 cm{sup 3} g−1 and high surface areas of 180 m{sup 2} g{sup −1} but they become reduced to 0.221 cm{sup 3} g{sup −1} and 113 m{sup 2} g{sup −1}, respectively upon WO{sub 3} incorporation, with tunable mesopore diameter in the range of 5–6.5 nm. TEM images show WO{sub 3}–TiO{sub 2} nanocomposites are quite uniform with 10–15 nm of TiO{sub 2} and 5–10 nm of WO{sub 3} sizes. Under UV illumination, the overall photocatalytic efficiency of the 3% WO{sub 3}–TiO{sub 2} nanocomposite is 3.5 and 6.6 times higher than that of mesoporous TiO{sub 2} and commercial UV-100 photocatalyst, respectively. The 3% WO{sub 3}–TiO{sub 2} nanocomposite is considered to be the optimum photocatalyst which is able to degrade completely (100% conversion) of imazapyr herbicide along 120 min with high photonic efficiency ∼8%. While under visible light illumination, the 0.5% WO{sub 3}–TiO{sub 2} nanocomposite is the optimum photocatalyst which achieves 46% photocatalytic efficiency.

  13. Effects of different petal thickness on gas sensing properties of flower-like WO3·H2O hierarchical architectures

    International Nuclear Information System (INIS)

    Zeng, Wen; Zhang, He; Wang, Zhongchang

    2015-01-01

    Graphical abstract: In this work, we prepare four different petal thicknesses of hierarchical WO 3 ·H 2 O architectures via a simple hydrothermal process, and systematically report their formation mechanisms and gas-sensing properties. - Highlights: • Flower-like WO 3 ·H 2 O architectures with different petal thickness were reported. • The WO 3 ·H 2 O sheet-flower sensor shows a significantly enhanced gas response. • A possible growth mechanism for the flower-like architectures is proposed. - Abstract: Hierarchical architectures consisting of two-dimensional (2D) nanostructures are of great interest for potential use in recent year. Here, we report the successful synthesis of four hierarchical tungsten oxide flower-like architectures via a simple yet facile hydrothermal method. The as-prepared WO 3 ·H 2 O hierarchical architectures are in fact assembled with numerous nanosheets or nanoplates. Through a comprehensive characterization of microstructures and morphologies of the as-prepared products, we find that petal thickness is a key factor for affecting gas-sensing performances. We further propose a possible growth mechanism for the four flower-like architectures. Moreover, gas-sensing measurements showed that the well-defined sheet-flower WO 3 ·H 2 O hierarchical architectures exhibited the excellent gas-sensing properties to ethanol owing to their largest amount of thin petal structures and pores

  14. Solvent directed morphologies and enhanced luminescent properties of BaWO4:Tm3+,Dy3+ for white light emitting diodes

    Science.gov (United States)

    Wu, Hongyue; Yang, Junfeng; Wang, Xiaoxue; Gan, Shucai; Li, Linlin

    2018-05-01

    A series of Tm3+ and Dy3+ codoped BaWO4 phosphors with tunable shapes were controllably synthesized by a facile solvothermal method. The effects of ratio of ethylene glycol (EG) and water on the morphologies of BaWO4 structures are systematically studied. It was discovered that the reason for these morphological changes is based on the reaction speed of the kinetic control, which relates to the strong chelating abilities of ethylene glycol. And when the solvent is pure ethylene glycol, the peanut-like BaWO4:Dy3+ has the strongest emission intensity. Moreover, the emission color of the phosphors varied from blue (0.232, 0.180) to white (0.268, 0.250) by controlling Dy3+ ions content with a fixed Tm3+ concentration. The energy transfer mechanism was investigated in detail. With increasing the doped concentration of Dy3+ ions, the energy transfer efficiency of BaWO4:0.005Tm3+,yDy3+ increased gradually and reached as high as 63% when the Dy3+ doped concentration is 0.03. The critical distance RC calculated by the spectral overlap method is about 19.93 Å, and it is in good agreement with that obtained using the concentration quenching method (19.70 Å), indicating that the electric dipole-dipole interaction is the main energy transfer mechanism for BaWO4:Tm3+,Dy3+ phosphors.

  15. Plasmodium falciparum parasites expressing pregnancy-specific variant surface antigens adhere strongly to the choriocarcinoma cell line BeWo

    DEFF Research Database (Denmark)

    Haase, Rikke N; Megnekou, Rosette; Lundquist, Maja

    2006-01-01

    Placenta-sequestering Plasmodium falciparum parasites causing pregnancy-associated malaria express pregnancy-specific variant surface antigens (VSA(PAM)). We report here that VSA(PAM)-expressing patient isolates adhere strongly to the choriocarcinoma cell line BeWo and that the BeWo line can...... be used to efficiently select for VSA(PAM) expression in vitro....

  16. The use of a concrete additive to eliminate returned concrete waste volumes

    Directory of Open Access Journals (Sweden)

    Bester Johannes

    2017-01-01

    Full Text Available This paper investigates the effects of the use of a recently developed two-component powdered product made from polymers and inorganic compounds that can be mechanically mixed into returned fresh ready-mix concrete to allow for the separation of the concrete into fine and coarse aggregates. This allows for the re-use of the returned concrete as aggregates in the manufacturing of new concrete. The returned concrete waste can therefore be eliminated, thus reducing virgin aggregate usage, as well as reducing the environmental impact of returned concrete. In this study, the treated recycled fresh concrete was separated into fine and coarse aggregates, and then used at replacement levels of 0%, 25%, 50%, 75% and 100%. The effect of the product on the material classification, and on important fresh and hardened properties of the concrete for the above-mentioned replacement values was tested. For the fine aggregate, the results indicate minimal changes in both the fresh and hardened properties. For the coarse aggregate, the results show a marked improvement of flexural strength with an increase in replacement value when coarse aggregates are used. Very high replacement levels may be used with very little effect on the quality of the new concrete.

  17. Study on properties of mortar using silica fume and ground blast furnace slag. Silica fume oyobi koro slag funmatsu wo mochiita mortar no tokusei ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Shiiba, H; Honda, S; Araki, A [Fukuoka University, Fukuoka (Japan). Faculty of Engineering

    1992-09-01

    The effect of silica fume and ground blast furnace slag in concrete on the content of superplasticizer, and dynamic properties of hardened mortar with such admixtures were studied experimentally. Although the dependence of a flow value on the superplasticizer was dominated by kinds of superplasticizers, blast furnace slag enhanced the flow value resulting in a high fluidity. Adsorption of superplasticizers onto admixtures was dependent on kinds of superplasticizers, and adsorption onto blast furnace slag was 1.3-2 times that onto normal Portland cement (NPC). The compressive strength of mortar increased by mixing admixtures, while the bending strength was enhanced only by mixing silica fume. Mixing mortar was lower in dynamic elastic modulus than NPC mortar at the same compressive strength, and the velocity of supersonic wave in mortar was scarcely affected by mixing. 11 refs., 14 figs., 3 tabs.

  18. Concrete Fibrations

    OpenAIRE

    Pagnan, Ruggero

    2017-01-01

    As far as we know, no notion of concrete fibration is available. We provide one such notion in adherence to the foundational attitude that characterizes the adoption of the fibrational perspective in approaching fundamental subjects in category theory and discuss it in connection with the notion of concrete category and the notions of locally small and small fibrations. We also discuss the appropriateness of our notion of concrete fibration for fibrations of small maps, which is relevant to a...

  19. [Artur Wołyński--A forgotten Polish historian in Italy in the second half of the 19th century].

    Science.gov (United States)

    Piskurewicz, Jan

    2011-01-01

    Artur Wołyński (1844-1893) was, undoubtedly, one of the most interesting personages of Polish émigrés after January Uprising. He belonged to these circles of Polish émigrés, who were able to reconcile their patriotic aspirations with realities and interest of the countries that entertained them. As far as Wołyński is concerned, it found its expression in the efforts that were made in order to assimilate two nations--Polish and Italian people--appealing to the common history and familiar cultural traditions. An important element of integrating all the above-discussed actions was his scientific activity. The mentioned activity included, first of all, his studies on Nicolaus Copernicus and Galileo Galilei. In the article were analyzed more comprehensive scientific descriptions dedicated to Copernicus and Galileo prepared by Wołyński, and their significance and opinions on them of the learned, whose works treated on Copernicus and Galileo as well. Secondly, in the field of scientific activity of Wołyńiski, one can also observe his researches and the process of elaborating sources for Polish and Italian his tory, particularly concerning the 17th century. However, most of his attention Wołyński paid to collecting and working out the materials concerning January Uprising. Speaking a modern language, one can say that Wołyński in a way polled the insurgents of January Uprising sending to them an appropriate list of questions, additionally allowing for their biographies. In the paper was also included a detailed description of this broad initiative together with its results. Up till now, not much attention has been paid to this significant scientific activity and its contexts. So, the present article is to remind of meritorious personage of Wołyński, and particularly of his output within the realm of history of science, history of Polish and Italian relationships, and of the role he played in bequeathing memory of January Uprising.

  20. Maintenance and preservation of concrete structures. Report 3: Abrasion-erosion resistance of concrete

    Science.gov (United States)

    Liu, T. C.

    1980-07-01

    This report describes a laboratory test program on abrasion-erosion resistance of concrete, including the development of a new underwater abrasion-erosion test method. This program was designed to evaluate the relative abrasion-erosion resistance of various materials considered for use in the repair of erosion-damaged concrete structures. The test program encompassed three concrete types (conventional concrete, fiber-reinforced concrete, and polymer concrete); seven aggregate types (limestone, chert, trap rock, quartzite, granite, siliceous gravel, and slag); three principal water-cement rations (0.72, 0.54, and 0.40); and six types of surface treatment (vacuum, polyurethane coating, acrylic mortar coating, epoxy mortar coating, furan resin mortar coating, and iron aggregate topping). A total of 114 specimens made from 41 batches of concrete was tested. Based on the test data obtained, a comprehensive evaluation of the effects of various parameters on the abrasion-erosion resistance of concrete was presented. Materials suitable for use in the repair of erosion-damaged concrete structures were recommended. Additional work to correlate the reported findings with field performance was formulated.

  1. Ferromagnetism and half metallicity induced by oxygen vacancies in the double perovskite BaSrNiWO{sub 6}: DFT study

    Energy Technology Data Exchange (ETDEWEB)

    Aharbil, Y. [Laboratoire de Chimie Physique des Matériaux LCPM, Faculté des Sciences Ben M' Sik, Casablanca (Morocco); Labrim, H. [Unité Science de la Matière/DERS/Centre National de l’Energie, des Sciences et des Techniques Nucléaires (CNESTEN), Rabat (Morocco); Benmokhtar, S.; Haddouch, M. Ait [Laboratoire de Chimie Physique des Matériaux LCPM, Faculté des Sciences Ben M' Sik, Casablanca (Morocco); Bahmad, L., E-mail: bahmad@fsr.ac.ma [Mohammed V University in Rabat, Laboratoire de Magnétisme et Physique des Hautes Energies L.M.P.H.E. URAC-12, B.P. 1014, Rabat (Morocco); Belhaj, A. [LIRST, Département de Physique, Faculté Poly-disciplinaire, Université Sultan Moulay Slimane, Béni Mellal (Morocco); Ez-Zahraouy, H.; Benyoussef, A. [Mohammed V University in Rabat, Laboratoire de Magnétisme et Physique des Hautes Energies L.M.P.H.E. URAC-12, B.P. 1014, Rabat (Morocco)

    2016-11-01

    Using the spin polarized density functional theory (DFT) and exploring the Plane-Wave Self-Consistent Field (PWscf) code implemented in Quantum-ESPRESSO package, we investigate the effect of the Oxygen vacancies (V{sub O}) and the Oxygen interstitial (O{sub i}) on the double perovskite BaSrNiWO{sub 6}. This deals with the magnetic ordering and the electronic structure in such a pure sample exhibiting the insulating anti-ferromagnetic (AFM) state. This study shows that the presence of oxygen deficient defects converts the insulating to half metal with ferromagnetic or anti-ferromagnetic states. The magnetic ordering in BaSrNiWO{sub 6−δ} depends on the position of the Oxygen vacancy in the unit cell. However, it has been shown that the Oxygen interstitial preserves the anti-ferromagnetic propriety. We have computed the formation energies of different positions of the Oxygen vacancy (V{sub O}) and the Oxygen interstitial (O{sub i}) in the BaSrNiWO{sub 6} compound. We showed that the formation of V{sub O} is easier and vice versa for the O{sub i} formation. The obtained results reveal(V{sub O}) and the Oxygen interstitial (O{sub i}) that the anti-ferromagnetic can be converted to ferromagnetic in the double perovskite BaSrNiWO{sub 6} induced by Oxygen vacancies V{sub O}. - Highlights: • We have studied the ferromagnetism and Half Metallicity in Double Perovskite BaSrNiWO{sub 6}. • We have applied the Ab-inito calculations using the DFT approach. • We showed the effects induced by Oxygen Vacancies and Oxygen interstitial. • We found that the magnetic ordering in BaSrNiWO{sub 6−δ} depends on the position of the Oxygen vacancy in the unit cell.

  2. Blue luminescence in Tm3+-doped KGd(WO4)2 single crystals

    International Nuclear Information System (INIS)

    Gueell, F.; Mateos, X.; Gavalda, Jna.; Sole, R.; Aguilo, M.; Diaz, F.; Massons, J.

    2004-01-01

    Up-conversion blue emissions of trivalent thulium ions in monoclinic KGd(WO 4 ) 2 single crystals at 454 and 479 nm are reported for a single pump laser source at 688 nm. We grew thulium-doped KGd(WO 4 ) 2 single crystals at several concentrations from 0.1% to 10%. We recorded a polarized optical absorption spectrum for the 3 F 2 + 3 F 3 energy levels of thulium at room temperature and low temperature (6 K). From the low temperature emission spectra we determined the splitting of the 3 H 6 ground state. The blue emissions are characterized as a function of the dopant concentration and temperature from 10 K to room temperature. To our knowledge, this is the first time that sequential two-photon excitation process (STEP) generated blue emissions in thulium-doped single crystals with a single excitation wavelength

  3. JCI Tokyo convention is held; JCI tokyo taikai wo kaisai

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-08-10

    For 3 days on 15{approx}17 of Julies, Japan Concrete Inst. (Toyokazu Shiire chairman) held concrete technology annual meeting in the Tokyo big site in Tokyo and Ariake. Various events such as ready-mixed concrete seminar (participant: 562 person), joint seminar with the Korea concrete institute, observation were developed 20th concrete technology lecture (paper the report: 521 case participant real number: 1400 person), 12th concrete fair (exhibit: 95 case attendance number: 10150 person) center on present convention. The opinion in which the party of the first line of various quarters became heated on the direction in which the ready-mixed concrete will ought to advance based on performance definition and internationalization in the ready-mixed concrete seminar in this inside in future was exchanged. Whether it is the JIS ready-mixed concrete and whether quality audit system are necessary why. The severe order of more cheaply supplying the better concrete in the responsibility of the factory, also came out. Within the special lecture (participant: 548 person), it was an interest of the nation who obtained the time too, the fact of the president election that it does secret story especially and comes out happily heard it. In the new planning, 'the concrete which the primary school child makes' (it is introduced in this journal No. 614) was exhibited in the tip in the fair place. The figure of parent and child companion who gazed at the masterpiece which broke through the preliminary in each place was conspicuous. The still, schedule that the annual meeting in next time is held in the Sendai City on July 7{approx}9, 1999. (translated by NEDO)

  4. LIGHTWEIGHT CONCRETE BASED GRANSHLAK

    Directory of Open Access Journals (Sweden)

    NETESA M. I.

    2016-02-01

    Full Text Available Raising of problem. Concrete advisable to obtain a low strength with local secondary resources for recycling and reduce the environmental burden on the environment. But it is important to design such concrete compositions with a reduced flow of cement. It is known that the coefficient of efficiency of use of cement in the concrete of the heavy and B10 is less than about 0.5, which is almost two times smaller than in class B15 concrete and above. Even lower coefficient of efficiency in light concrete cement low strength. Therefore, it is important to find patterns determining the composition of lightweight concrete based on local-products industry with more efficient use of cement in them. Purpose.. Based on the analysis of earlier research results, including with the use of methods of mathematical planning of experiments to determine the concrete contents, which can provide the requirements for the underlying layers of the floor, the compressive strength of which should correspond to the class B5. It is important to provide the required strength at minimum flow of the cement, which is the most expensive and energy-intensive part of concrete. Conclusion. Analysis of the test results of control samples of concrete in 28-day-old, the following laws. The required tensile strength of concrete compressive strength of 7.0 MPa can be obtained in the test range when used in formulations as a filler as the Dnieper hydroelectric power station fly ash and tailings Krivoy Rog iron ore YuGOK. To ensure providing the required characteristic strength of the concrete in the underlying layers of the floor is advisable to use a nominal composition per cubic meter of concrete: cement 160 kg granshlaka Plant named after Petrovsky, 675 kg of fly ash Dnieper HPP 390 kg, 400 kg of sand, 230 liters of water. Thus, while ensuring rational grain composition components can obtain the desired strength lightweight concrete based granshlaka plant Petrovsky, using as fillers

  5. Concrete quality assurance

    Energy Technology Data Exchange (ETDEWEB)

    Holz, N. [Harza Engineering Company, Chicago, IL (United States)

    2000-08-01

    This short article reports on progress at the world's largest civil construction project, namely China's Three Gorges hydro project. Work goes on around the clock to put in place nearly 28 M m{sup 3} of concrete. At every stage of the work there is strong emphasis on quality assurance (QA) and concrete is no exception. The US company Harza Engineering has been providing QA since the mid-1980s and concrete QA has been based on international standards. Harza personnel work in the field with supervisors developing educational tools for supervising concrete construction and quality, as well as providing training courses in concrete technology. Some details on flood control, capacity, water quality and environmental aspects are given..

  6. Photocatalytic activity of bipolar pulsed magnetron sputter deposited TiO{sub 2}/TiWO{sub x} thin films

    Energy Technology Data Exchange (ETDEWEB)

    Weng, Ko-Wei; Hu, Chung-Hsuan; Hua, Li-Yu; Lee, Chin-Tan [Department of Electronic Engineering, National Quemoy University, 1 Daxue Road, Jinning Township, Kinmen 89250, Taiwan, ROC (China); Zhao, Yu-Xiang [Department of Computer Science and Information Engineering, National Quemoy University, Taiwan, ROC (China); Chang, Julian; Yang, Shu-Yi [Department of Applied English, National Quemoy University, Taiwan, ROC (China); Han, Sheng, E-mail: shenghan@nutc.edu.tw [Center for General Education, National Taichung University of Science and Technology, 129 San-min Road, Section 3, Taichung 40401, Taiwan, ROC (China)

    2016-08-15

    Highlights: • TiO{sub 2}/TiWO{sub x} films were fabricated by a bipolar pulsed magnetron sputtering apparatus. • Titanium oxide being sputtered tungsten enhanced the highly oriented of TiO{sub 2} (1 0 1) plane of the specimen assemblies. • The mechanism WO{sub 3}(h{sup +}, e{sup −})/TiO{sub 2}(h{sup +}, e{sup −}) → WO{sub 3}(e{sup −})/TiO{sub 2}(h{sup +}) shows the higher hydrophilicity and lower contact angle. - Abstract: Titanium oxide films were formed by sputtering and then TiWO{sub x} films were deposited by bipolar pulsed magnetron sputtering with pure titanium and tungsten metal targets. The sputtering of titanium oxide with tungsten enhanced the orientation of the TiO{sub 2} (1 0 1) plane of the specimen assemblies. The main varying parameter was the tungsten pulse power. Titanium oxide sputtered with tungsten using a pulsing power of 50 W exhibited a superior hydrophilic property, and a contact angle of 13.1°. This fabrication conditions maximized the photocatalytic decomposition of methylene blue solution. The mechanism by which the titanium oxide was sputtered with tungsten involves the photogeneration of holes and electron traps, inhibiting the hole–electron recombination, enhancing hydrophilicity and reducing the contact angle.

  7. Sulfur Nanoparticles Synthesis and Characterization from H2S Gas, Using Novel Biodegradable Iron Chelates in W/O Microemulsion

    Directory of Open Access Journals (Sweden)

    Harle Arti

    2008-01-01

    Full Text Available AbstractSulfur nanoparticles were synthesized from hazardous H2S gas using novel biodegradable iron chelates in w/o microemulsion system. Fe3+–malic acid chelate (0.05 M aqueous solution was studied in w/o microemulsion containing cyclohexane, Triton X-100 andn-hexanol as oil phase, surfactant, co-surfactant, respectively, for catalytic oxidation of H2S gas at ambient conditions of temperature, pressure, and neutral pH. The structural features of sulfur nanoparticles have been characterized by X-ray diffraction (XRD, transmission electron microscope (TEM, energy dispersive spectroscopy (EDS, diffused reflectance infra-red Fourier transform technique, and BET surface area measurements. XRD analysis indicates the presence of α-sulfur. TEM analysis shows that the morphology of sulfur nanoparticles synthesized in w/o microemulsion system is nearly uniform in size (average particle size 10 nm and narrow particle size distribution (in range of 5–15 nm as compared to that in aqueous surfactant systems. The EDS analysis indicated high purity of sulfur (>99%. Moreover, sulfur nanoparticles synthesized in w/o microemulsion system exhibit higher antimicrobial activity (against bacteria, yeast, and fungi than that of colloidal sulfur.

  8. HT-solution growth and characterisation of In{sub x}Na{sub x}Mn{sub 1-2x}WO{sub 4} (0

    Energy Technology Data Exchange (ETDEWEB)

    Gattermann, U. [Sektion Kristallographie, Department für Geo- und Umweltwissenschaften, Ludwig-Maximilians-Universität München, Theresienst rasse 41, D-80333 Munich (Germany); Park, S.-H., E-mail: sohyun.park@lmu.de [Sektion Kristallographie, Department für Geo- und Umweltwissenschaften, Ludwig-Maximilians-Universität München, Theresienst rasse 41, D-80333 Munich (Germany); Paulmann, C. [Geowissenschaften, Fakultät für Mathematik, Informatik und Naturwissenschaften, Universität Hamburg, Grindelallee 48, D-20146 Hamburg (Germany); Benka, G.; Pfleiderer, C. [Physik-Department, Technische Universität München, James-Franck-Strasse 1, D-85748 Garching (Germany)

    2016-12-15

    A new solid solution system, In{sub x}Na{sub x}Mn{sub 1–2x}WO{sub 4} (0WO{sub 4}-type multiferroics was investigated. Large single crystals were grown up to several mm in length from high-temperature oxide solutions using a solvent mixture of Na{sub 2}WO{sub 4} and Na{sub 2}W{sub 2}O{sub 7}. Quantitative doping degrees were analyzed by means of electron microprobe. Single crystal X-ray diffraction studies agreed with the polar space group P2 for In{sub x}Na{sub x}Mn{sub 1–2x}WO{sub 4}. The complexity of partial (Na{sup +}/Mn{sup 2+})- and (In{sup 3+}/Mn{sup 2+})-ordering makes their atomic sites unique, explaining the dissymmetrization from P2/c down to P2. This is also valid for the InNaW{sub 2}O{sub 8}-type Mn{sub 2y}In{sub 1-y}Na{sub 1-y}W{sub 2}O{sub 8} solid solution found as co-product in this study. Specific heat and magnetisation measurements showed a paramagnetic dilution effect from (In{sup 3+}/Na{sup +})-doping while lowering the transition temperature for the multiferroic phase AF2 of In{sub x}Na{sub x}Mn{sub 1–2x}WO{sub 4} with respect to the prototype MnWO{sub 4}. - Graphical abstract: A volume expansion around Mn2 site by (In, Na)-doping is drawn by the atomic shifts in a Mn2O{sub 6} octahedron in the atomistic structure of In{sub 0.20(2)}Na{sub 0.17(2)}Mn{sub 0.63(4)}WO{sub 4} from the respective atomic positions of In-free MnWO{sub 4}. The size and direction of arrows are scaled up for indicating the consequent local distortion. - Highlights: • HT solution crystal growth of (In, Na):MnWO{sub 4}-solid-solution compounds. • Polar space group symmetry P2 for their atomistic structures. • Magnetic properties of the multiferroic phase AF2 by (In{sup 3+}, Na{sup +})-doping. • Magnetic phase transitions.

  9. Concrete and criticality

    International Nuclear Information System (INIS)

    Carter, R.D.

    1978-01-01

    Concrete is a widely used structural material which occurs frequently in systems requiring criticality analyses. Ordinarily, we give little thought to what its actual composition is (as compared to reference compositions), yet in criticality safety, differences in composition can cause large changes in k-effective and it may not be easy to predict in which direction the change will occur. Concrete composition is quite variable with differences in the aggregate used in the concrete in various parts of the country providing relative large differences in k-effective. The water content of concrete can also strongly affect the reactivity of a system in which it acts as a reflector or is interspersed between fissile units. Because concrete is so common and is often (but not always) a better reflector than water, one must know the concrete compositions or be prepared to use a ''worst case'' composition. It may be a problem, however, to determine just what is the worst case. At the Hanford Plant, the aggregate normally used is basalt, which gives a composition very low in carbon as opposed to those areas (e.g., Oak Ridge) where the use of limestone aggregate will result in concrete with a high carbon content. The data presented show some of the effects found in situations using ''Hanford'' concrete, but similar effects might be found with other compositions. In some cases, the use of concrete may be incidental to the effects shown. While the numbers shown are those for actual systems, the primary intent is to alert the reader that these effects can occur. In applying this information, the analyst should use material specific to the systems being analyzed

  10. Biodecontamination of concrete

    International Nuclear Information System (INIS)

    Hamilton, M.A.; Rogers, R.D.; Benson, J.

    1996-01-01

    A novel technology for biologically decontaminating concrete is being jointly developed by scientists at the Idaho National Engineering Laboratory (INEL) and British Nuclear Fuels plc (BNFL). The technology exploits a naturally occurring phenomenon referred to as microbially influenced degradation (MID) in which bacteria produce acids that dissolve the cement matrix of concrete. Most radionuclide contamination of concrete is fixed in the outer few mm of the concrete surface. By capturing and controlling this natural process, a biological method of removing the surface of concrete to depths up to several mm is being developed. Three types of bacteria are known to be important in MID of concrete: nitrifying bacteria that produce nitric acid, sulfur oxidizing bacteria that produce sulfuric acid, and certain heterotrophic bacteria that produce organic acids. An investigation of natural environments demonstrated with scanning electron microscopy the presence of bacteria on concrete surfaces of a variety of structures, such as bridges and dams, where corrosion is evident. Enumeration of sulfur oxidizing and nitrifying bacteria revealed their presence and activity on structures to varying degrees in different environments. Under ideal conditions, Thiobacillus thiooxidans, a sulfur oxidizing bacteria, attached to and colonized the surface of concrete specimens. Over 1mm depth of material from a 10 cm x 10 cm square surface was removed in 68 days in the Thiobacillus treated specimen compared to a sterile control. Laboratory and field demonstrations are currently being conducted using experimental chambers designed to be mounted directly to concrete surfaces where radionuclide contamination exists. Data is being obtained in order to determine actual rates of surface removal and limitations to the system. This information will be used to develop a full scale decontamination technology

  11. Concrete and prestressing process, container made with this concrete

    International Nuclear Information System (INIS)

    Gerard, M.

    1992-01-01

    Shape memory alloy fibers or heat shrinking fibers are encapsulated in a standard concrete. Prestressed concrete is obtained by heat treatment. Application is made to the fabrication of radioactive waste containers

  12. Let’s Get Concrete!

    DEFF Research Database (Denmark)

    Jones, Candace; Boxenbaum, Eva

    whereas in the United States market and professional logics interacted: manufacturers cooperated to create standards for concrete and appealed to architects as consumers. Our findings also illuminate that concrete was legitimated initially by imitation of stone, but this strategy soon de......-legitimated not only concrete but also stone. Concrete was perceived as merely imitative and thus inauthentic. For concrete to become a legitimate and widely adopted material, architects had to theorize concrete as unique material with distinctive aesthetic possibilities, which led to new kinds of buildings and new...... architectural styles. Our study illuminates the key role that materials and aesthetics played within architects’ professional logic and shaped processes of institutional change....

  13. Electro-deposition metallic tungsten coatings in a Na{sub 2}WO{sub 4}-WO{sub 3} melt on copper based alloy substrate

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Y.H., E-mail: dreamerhong77@126.com [School of Materials Science and Engineering, University of Science and Technology Beijing, 30 Xueyuan Road, Haidian District, Beijing 100083 (China); Zhang, Y.C.; Liu, Q.Z.; Li, X.L.; Jiang, F. [School of Materials Science and Engineering, University of Science and Technology Beijing, 30 Xueyuan Road, Haidian District, Beijing 100083 (China)

    2012-11-15

    Highlights: Black-Right-Pointing-Pointer The tungsten coating (>1 mm) was obtained by electro-deposition method in molten salt. Black-Right-Pointing-Pointer Different thickness tungsten coatings were obtained by using different durations. Black-Right-Pointing-Pointer Good performance of coating was obtained when pulse parameters were modulated. - Abstract: The tungsten coating was prepared by electro-deposition technique on copper alloy substrate in a Na{sub 2}WO{sub 4}-WO{sub 3} melt. The coating's surface and cross-section morphologies as well as its impurities were investigated by XPS, SEM and line analysis. Various plating durations were investigated in order to obtain an optimal coating's thickness. The results demonstrated that the electro-deposited coating was compact, voidless, crackless and free from impurities. The tungsten coating's maximum Vickers hardness was measured to be 520 HV. The tungsten coating's minimum oxygen content was determined to be 0.018 wt%. Its maximum thickness was measured to be 1043.67 {mu}m when the duration of electrolysis was set to 100 h. The result of this study has demonstrated the feasibility of having thicker tungsten coatings on copper alloy substrates. These electrodeposited tungsten coatings can be potentially implemented as reliable armour for the medium heat flux plasma facing component (PFC).

  14. Wafer-scaled monolayer WO{sub 3} windows ultra-sensitive, extremely-fast and stable UV-A photodetection

    Energy Technology Data Exchange (ETDEWEB)

    Hai, Zhenyin; Akbari, Mohammad Karbalaei [Ghent University Global Campus, Department of Applied Analytical & Physical Chemistry, Faculty of Bioscience Engineering, 119 Songdomunhwa-ro, Yeonsu-gu, Incheon 21985 (Korea, Republic of); Xue, Chenyang [Key Laboratory of Instrumentation Science and Dynamic Measurement of Ministry of Education, North University of China, Taiyuan, Shanxi 030051 (China); Xu, Hongyan [School of Materials Science and Engineering, North University of China, Taiyuan, Shanxi 030051 (China); Hyde, Lachlan [Melbourne Centre for Nanofabrication, Clayton, Victoria 3168 (Australia); Zhuiykov, Serge, E-mail: serge.zhuiykov@ugent.be [Ghent University Global Campus, Department of Applied Analytical & Physical Chemistry, Faculty of Bioscience Engineering, 119 Songdomunhwa-ro, Yeonsu-gu, Incheon 21985 (Korea, Republic of)

    2017-05-31

    Highlights: • Monolayer WO{sub 3}-based photodetectors were fabricated for the first time. • The device has ultrafast response time of ∼40 μs and responsivity of ∼0.329 A W{sup −1}. • The response time is 400-fold improvement over any other WO{sub 3} UV photodetectors. • The device has better characteristics than many 2D materials-based photodetectors. • This proposed strategy has great potential for commercialization of photodetectors. - Abstract: The monolayer WO{sub 3}-based UV-A photodetectors, fabricated by atomic layer deposition (ALD) technique at the large area of SiO{sub 2}/Si wafer, have demonstrated vastly improved functional capabilities: extremely fast response time of less than 40 μs and photoresponsivity reaching of ∼0.329 A W{sup −1}. Their ultrafast photoresponse time is at least 400-fold improvement over the previous reports for any other WO{sub 3}-based UV photodetectors that have ever been fabricated, and significantly faster than most of other photodetectors based on two-dimensional (2D) nanomaterials reported-to-date. Moreover, their measured long-term stability exceeds more than 200 cycles without any visible degradation. The ALD-deposited WO{sub 3} monolayer has also exhibited wider bandgap of 3.53 eV and the UV-A photodetector based on it is environmentally friendly, highly reliable, with excellent reproducibility and long-term stability. Thus, the shift to mono-layered semiconductors, which possess completely new quantum-confined effects, has the greatest potential in creating a new class of nano-materials, which in return windows new functional opportunities for various opto-electronic instruments built on semiconductor monolayer and, more importantly, can result in new strategy for fabrication highly-flexible, inexpensive and extremely-sensitive devices. This strategy also opens up the great opportunities for industrialization and commercialization of the photodetectors and other optoelectronic devices based on

  15. TiO_2/WO_3 photoactive bilayers in the UV-Vis light region

    International Nuclear Information System (INIS)

    Vasilaki, E.; Vernardou, D.; Kenanakis, G.; Katsarakis, N.; Vamvakaki, M.

    2017-01-01

    In this work, photoactive bilayered films consisting of anatase TiO_2 and monoclinic WO_3 were synthesized by a sol-gel route. Titanium isopropoxide and tungsten hexachloride were used as metal precursors and deposition was achieved by spin-coating on Corning glass substrates. The samples were characterized by X-ray diffraction, photoluminescence, UV-Vis, and Raman spectroscopy, as well as field emission scanning electron microscopy. The prepared immobilized catalysts were tested for their photocatalytic performance by the decolorization of methylene blue in aqueous matrices, under UV-Vis light irradiation. The annealing process influenced the crystallinity of the bilayered films, while the concentration of the tungsten precursor solution and the position of the tungsten trioxide layer further affected their photocatalytic performance. In particular, the photocatalytic performance of the bilayered films was optimized at a concentration of 0.1 M of the WO_3 precursor solution, when deposited as an overlying layer on TiO_2 by two annealing steps (∝76% methylene blue decolorization in 300 min of irradiation versus ∝59% in the case of a bare TiO_2 film). In general, the coupled layer catalysts exhibited superior photoactivity compared to that of bare TiO_2 films with WO_3 acting as an electron trap, resulting, therefore, in a more efficient electron-hole separation and inhibiting their recombination. (orig.)

  16. N, Fe and WO3 modified TiO2 for degradation of formaldehyde

    International Nuclear Information System (INIS)

    Tong Haixia; Zhao Li; Li Dan; Zhang Xiongfei

    2011-01-01

    Graphical abstract: The undoped TiO 2 powder (T(0)) shows strong photoabsorption only at wavelengths shorter than 400 nm, and while Fe 3+ and N-doped TiO 2 nanoparticles show photoabsorption in visible region and the absorption edge shifts to a longer wavelength. WO 3 compounding also benefits the photoabsorption in visible region. Display Omitted Highlights: → The preparation of the catalysts co-doped by Fe, N and compounded by WO 3 . → The obvious sculptured 'pattern' of the catalysts doped by Fe in the SEM images. → Strengthened photoabsorption to visible light of the modified catalysts from UV-DRS analysis. - Abstract: Butyltitanate, ethanol and glacial acetic acid were chosen as titanium source, solvent and chelating agent, respectively, via a sol-gel method combined impregnation method to prepare N, Fe co-doped and WO 3 compounded photocatalyst TiO 2 powder. The synthesized products were characterized by X-ray diffraction (XRD), diffuse reflectance UV-Vis spectra (UV-DRS), scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy (XPS). Photocatalytic degradation of formaldehyde was employed to investigate the catalytic activity. The results show that the degradation rate is 77.61% in 180 min under UV light irradiation when the concentration of N is fixed on, and the optimum proportioning ratio of n(Fe):n(W):n(Ti) is 0.5:2:100.

  17. The spectroscopy investigation of ZnWO{sub 4}:Tm{sup 3+} single crystal

    Energy Technology Data Exchange (ETDEWEB)

    Yang Fugui, E-mail: ruopiao@fjirsm.ac.cn [Department of Electronic Information Science, Fujian Jiangxia University, Fuzhou, Fujian 350108 (China); Tu Chaoyang [Fujian Institute of Research on the Structure of Matter, Chinese Academy of Sciences, Fuzhou, Fujian 350002 (China)

    2012-09-15

    Highlights: Black-Right-Pointing-Pointer The spectroscopy and refractive index of single crystal ZnWO{sub 4}:Tm{sup 3+} are investigated systematically. Black-Right-Pointing-Pointer The Judd-Ofelt parameters are obtained. Black-Right-Pointing-Pointer The gain cross sections at {approx}2 {mu}m are estimated by reciprocity method (RM). Black-Right-Pointing-Pointer The laser operation at {approx}2 {mu}m is discussed. - Abstract: The single crystal ZnWO{sub 4}:Tm{sup 3+} has been grown by Czochralski method. The XRD, refractive index, absorption and fluorescence spectra are measured. The Judd-Ofelt parameters{Omega}{sub 2}, {Omega}{sub 4}, {Omega}{sub 6} are obtained to be 6.3 Multiplication-Sign 10{sup -20}, 1.3 Multiplication-Sign 10{sup -20}, 1.4 Multiplication-Sign 10{sup -20} cm{sup 2}, respectively. The fluorescence decay time of the {sup 3}H{sub 4} level is measured to be 0.113 ms and the quantum efficiency is 57%. The gain cross sections corresponding to {sup 3}F{sub 4}{yields}{sup 3}H{sub 6} transition at {approx}2 {mu}m are estimated by the reciprocity method (RM). The strong gain at {approx}2 {mu}m indicates that the ZnWO{sub 4}:Tm{sup 3+} crystal is a promising laser host for {approx}2 {mu}m laser.

  18. Ultrafine particles in concrete: Influence of ultrafine particles on concrete properties and application to concrete mix design

    Energy Technology Data Exchange (ETDEWEB)

    Vogt, Carsten

    2010-07-01

    In this work, the influence of ultrafine particles on concrete properties was investigated. In the context of this work, ultrafine particles (reactive and inert materials) are particles finer than cement. Due to the development of effective superplasticizers, the incorporation of ultrafine particles in concrete is nowadays possible. Different minerals, usually considered inert, were tested. These minerals were also used in combination with reactive silica fume. The modified Andreassen model was used to optimise the particle size distribution and thus the packing density of the complete mix composition. Heat of hydration, compressive strength, shrinkage, frost resistance and the microstructure were investigated.The influence of different ultrafine inert materials on the cement hydration was investigated. The results show that most of the minerals have an accelerating effect. They provide nucleation sites for hydration products and contribute in that way to a faster dissolution of cement grains. Minerals containing calcium were found to influence the early stage of hydration as well. These minerals shortened the dormant period of the cement hydration, the effect is known from limestone filler in self-compacting concrete. In a first test series on concrete, different ultrafine inert particles were used to replace cement. That was done in several ways; with constant water content or constant w/c. The results from this test series show that the best effect is achieved when cement is replaced by suitable ultrafines while the w/c is kept constant. In doing so, the compressive strength can be increased and shrinkage can be reduced. The microstructure is improved and becomes denser with improved packing at microlevel. Efficiency factors (k values) for the ultrafine inert materials were calculated from the compressive strength results. The k values are strongly dependent on the mode of cement replacement, fineness and type of the replacement material and curing time. Drying

  19. CONCRETE MIX DESIGN FOR STRUCTURES SUBJECTED TO EXPOSURE CLASS XC1 DEPENDING ON CONCRETE COVER

    Directory of Open Access Journals (Sweden)

    O. Yu. Cherniakevich

    2016-01-01

    Full Text Available The reinforced steel corrosion which is the most important problem of reinforced concrete structures durability is generally stipulated for carbonization of concrete surrounding it. Concrete cover calculation at the design stage is predicated one because of the differences in manufacturing conditions and use of constructions. The applying of the probabilistic approaches to the carbonation process modeling allows to get predicated grade of the depth of carbonization of concrete and, thus, to settle minimum concrete cover thickness for a given projected service life of a construction. The procedures for concrete mix design for different strength classes of concrete are described in the article. Current recommendations on assignment of concrete strength class as well as concrete cover are presented. The European Standard EN 206:2013 defines the content requirements for the concrete structures operated in the exposure class XC1, including the minimum values of water-cement ratio, minimum cement content, and minimum strength class of concrete. Since the standard does not include any basis or explanations of the requirements, we made an effort to develop a scientific justification for the mentioned requirements. We developed the probabilistic models for the process of carbonation of concrete based on the concrete mix which was designed using the software VTK-Korroziya. The reinforced concrete structures with concrete cover 20–35 mm operated in the most unfavorable conditions within the exposure class XC1 were analyzed. The corresponding probabilistic calculations of the depth of carbonated concrete are described in the article. 

  20. Concrete portable handbook

    CERN Document Server

    Woodson, R Dodge

    2011-01-01

    Whether or not, you are on the job site or back in the office, this book will help you to avoid mistakes, code violations, and wasted time and money. The book's four part treatment begins with constituent materials followed by self contained parts on Concrete Properties, Processes, and Concrete Repair and Rehabilitation. Designed to be an ""all in one"" reference, the author includes a wealth information for the most popular types of testing. This includes: Analysis of Fresh Concrete; Testing Machines; Accelerated Testing Methods; Analysis of Hardened Concrete and Mortar; Core Sampl

  1. Autogenous Deformation of Concrete

    DEFF Research Database (Denmark)

    Autogenous deformation of concrete can be defined as the free deformation of sealed concrete at a constant temperature. A number of observed problems with early age cracking of high-performance concretes can be attributed to this phenomenon. During the last 10 years , this has led to an increased...... focus on autogenous deformation both within concrete practice and concrete research. Since 1996 the interest has been significant enough to hold international, yearly conferences entirely devoted to this subject. The papers in this publication were presented at two consecutive half-day sessions...... at the American Concrete Institute’s Fall Convention in Phoenix, Arizona, October 29, 2002. All papers have been reviewed according to ACI rules. This publication, as well as the sessions, was sponsored by ACI committee 236, Material Science of Concrete. The 12 presentations from 8 different countries indicate...

  2. A novel biosensor based on the direct electrochemistry of horseradish peroxidase immobilized in the three-dimensional flower-like Bi_2WO_6 microspheres

    International Nuclear Information System (INIS)

    Liu, Hui; Guo, Kai; Duan, Congyue; Chen, Xianjin; Zhu, Zhenfeng

    2016-01-01

    Three-dimensional flower-like Bi_2WO_6 microspheres (3D-Bi_2WO_6 MSs) have been synthesized through a simple hydrothermal method. The morphology and structure of 3D-Bi_2WO_6 MSs were characterized by scanning electron microscopy (SEM) and X-ray diffraction (XRD). The 3D-Bi_2WO_6 MSs subsequently were used to immobilize horseradish peroxidase (HRP) and fabricate a mediator-free biosensor for the detection of H_2O_2. Spectroscopic and electrochemical results reveal that 3D-Bi_2WO_6 MSs constitute an excellent immobilization matrix with biocompatibility for enzymes. Meanwhile, due to unique morphology of the flower-like microspheres, the direct electron transfer of HRP is facilitated and the prepared biosensors display good performances for the detection of H_2O_2 with a wide linear range, including two linear sections: 0.5–100 μM (R"2 = 0.9983) and 100–250 μM (R"2 = 0.9981), as well as an extremely low method detection limit of 0.18 μM. - Highlights: • 3D-Bi_2WO_6 microspheres are used to fabricate a mediator-free biosensor firstly. • The biosensor displays a wide linear range of 0.5–250 μM for H_2O_2. • The biosensor exhibits a low detection limit of 0.18 μM for H_2O_2.

  3. Behaviour of concrete beams reinforced withFRP prestressed concrete prisms

    Science.gov (United States)

    Svecova, Dagmar

    The use of fibre reinforced plastics (FRP) to reinforce concrete is gaining acceptance. However, due to the relatively low modulus of FRP, in comparison to steel, such structures may, if sufficient amount of reinforcement is not used, suffer from large deformations and wide cracks. FRP is generally more suited for prestressing. Since it is not feasible to prestress all concrete structures to eliminate the large deflections of FRP reinforced concrete flexural members, researchers are focusing on other strategies. A simple method for avoiding excessive deflections is to provide sufficiently high amount of FRP reinforcement to limit its stress (strain) to acceptable levels under service loads. This approach will not be able to take advantage of the high strength of FRP and will be generally uneconomical. The current investigation focuses on the feasibility of an alternative strategy. This thesis deals with the flexural and shear behaviour of concrete beams reinforced with FRP prestressed concrete prisms. FRP prestressed concrete prisms (PCP) are new reinforcing bars, made by pretensioning FRP and embedding it in high strength grout/concrete. The purpose of the research is to investigate the feasibility of using such pretensioned rebars, and their effect on the flexural and shear behaviour of reinforced concrete beams over the entire loading range. Due to the prestress in the prisms, deflection of concrete beams reinforced with this product is substantially reduced, and is comparable to similarly steel reinforced beams. The thesis comprises both theoretical and experimental investigations. In the experimental part, nine beams reinforced with FRP prestressed concrete prisms, and two companion beams, one steel and one FRP reinforced were tested. All the beams were designed to carry the same ultimate moment. Excellent flexural and shear behaviour of beams reinforced with higher prestressed prisms is reported. When comparing deflections of three beams designed to have the

  4. Evaluation of concrete recycling system efficiency for ready-mix concrete plants.

    Science.gov (United States)

    Vieira, Luiz de Brito Prado; Figueiredo, Antonio Domingues de

    2016-10-01

    The volume of waste generated annually in concrete plants is quite large and has important environmental and economic consequences. The use of fresh concrete recyclers is an interesting way for the reuse of aggregates and water in new concrete production. This paper presents a study carried out for over one year by one of the largest ready-mix concrete producers in Brazil. This study focused on the evaluation of two recyclers with distinct material separation systems, herein referred to as drum-type and rotary sieve-type equipment. They were evaluated through characterization and monitoring test programs to verify the behaviour of recovered materials (aggregates, water, and slurry). The applicability of the recovered materials (water and aggregates) was also evaluated in the laboratory and at an industrial scale. The results obtained with the two types of recyclers used were equivalent and showed no significant differences. The only exception was in terms of workability. The drum-type recycler generated fewer cases that required increased pumping pressure. The analysis concluded that the use of untreated slurry is unfeasible because of its intense negative effects on the strength and workability of concrete. The reclaimed water, pre-treated to ensure that its density is less than 1.03g/cm(3), can be used on an industrial scale without causing any harm to the concrete. The use of recovered aggregates consequently induces an increase in water demand and cement consumption to ensure the workability conditions of concrete that is proportional to the concrete strength level. Therefore, the viability of their use is restricted to concretes with characteristic strengths lower than 25MPa. Copyright © 2016 Elsevier Ltd. All rights reserved.

  5. Photoelectrocatalytic degradation of diazo dyes on nanostructured WO{sub 3} electrodes

    Energy Technology Data Exchange (ETDEWEB)

    Hepel, Maria [Department of Chemistry, State University of New York at Potsdam, Potsdam, NY 13676 (United States)]. E-mail: hepelmr@potsdam.edu; Hazelton, Sandra [Department of Chemistry, State University of New York at Potsdam, Potsdam, NY 13676 (United States)

    2005-09-05

    Photoelectrocatalytic degradation of Remazol Black B (RBB) dye in aqueous solutions was investigated. The degradation was carried out on a highly efficient n-WO{sub 3} photoelectrode, which was synthesized by electrochemical processing. Effects of various synthesis and post-treatment conditions were investigated using electrochemical techniques and AFM imaging. Photocurrent measurements have shown that Butler-Gartner equation is fulfilled for n-WO{sub 3} films, which allowed us to determine the flat-band potential (E {sub fb} = 0.35 V versus Ag/AgCl, for pH = 0). The WO{sub 3} film electrode was found to be a better photelectrocatalyst than TiO{sub 2} with similar AFM surface roughness. Kinetic measurements of photoelectrocatalytic RBB degradation have shown that a generalized Langmuir-Hinshelwood model applies to the system, leading to the overall rate constant k' = 1.1 x 10{sup -9} mol cm{sup -2} s{sup -1}, with RBB adsorption equilibrium constant K = 3.35 x 10{sup 4} mol{sup -1} L and Gibbs free energy of adsorption {delta}G deg. = -6.16 kcal/mol (-25.8 kJ/mol). In mechanistic considerations of possible lines of oxidative attack on RBB, we looked at electrolyte composition and properties of electronic structure of RBB, by utilizing quantum mechanical calculations of molecular orbitals. The ab initio SCF Hartree-Fock calculations of molecular orbitals were carried out to evaluate most vulnerable areas of RBB molecule for electrophilic and nucleophilic attacks, as well as for a direct charge transfer oxidation process. Several electronic properties were mapped onto the total electron density surface and analyzed to reveal initial reaction pathways for oxidative degradation of RBB.

  6. Optical temperature sensing by upconversion luminescence of Er doped Bi5TiNbWO15ferroelectric materials

    Directory of Open Access Journals (Sweden)

    Hua Zou

    2014-12-01

    Full Text Available The Er3+ doped Bi5TiNbWO15 ceramics have been synthesized using conventional solid-state reaction techniques. The crystal structure, ferroelectric properties, UC emission properties and especially the temperature sensing behaviors were systematically studied. With increasing Er3+ content, the investigation of XRD pattern, the ferroelectric loop and the UC emission indicated that the Er3+ ions dopants preferentially substituted the A sites of Bi3TiNbO9 and then Bi2WO6. Based on fluorescence intensity ratio (FIR technique, the observed results implied the ceramics were promising candidates for temperature sensors in the temperature range of 175 K −550 K. More importantly, this study provided a contrast of temperature sensitivity between emission from the same part (Bi3TiNbO9 in bismuth layered-structure and emission from the different part (Bi3TiNbO9 and Bi2WO6 in bismuth layered-structure for the first time.

  7. WO3/Pt nanoparticles are NADPH oxidase biomimetics that mimic effector cells in vitro and in vivo

    International Nuclear Information System (INIS)

    Clark, Andrea J; Coury, Emma L; Meilhac, Alexandra M; Petty, Howard R

    2016-01-01

    To provide a means of delivering an artificial immune effector cell-like attack on tumor cells, we report the tumoricidal ability of inorganic WO 3 /Pt nanoparticles that mimic a leukocyte’s functional abilities. These nanoparticles route electrons from organic structures and electron carriers to form hydroxyl radicals within tumor cells. During visible light exposure, WO 3 /Pt nanoparticles manufacture hydroxyl radicals, degrade organic compounds, use NADPH, trigger lipid peroxidation, promote lysosomal membrane disruption, promote the loss of reduced glutathione, and activate apoptosis. In a model of advanced breast cancer metastasis to the eye’s anterior chamber, we show that WO 3 /Pt nanoparticles prolong the survival of 4T1 tumor-bearing Balb/c mice. This new generation of inorganic photosensitizers do not photobleach, and therefore should provide an important therapeutic advance in photodynamic therapy. As biomimetic nanoparticles destroy targeted cells, they may be useful in treating ocular and other forms of cancer. (paper)

  8. WO3/Pt nanoparticles are NADPH oxidase biomimetics that mimic effector cells in vitro and in vivo

    Science.gov (United States)

    Clark, Andrea J.; Coury, Emma L.; Meilhac, Alexandra M.; Petty, Howard R.

    2016-02-01

    To provide a means of delivering an artificial immune effector cell-like attack on tumor cells, we report the tumoricidal ability of inorganic WO3/Pt nanoparticles that mimic a leukocyte’s functional abilities. These nanoparticles route electrons from organic structures and electron carriers to form hydroxyl radicals within tumor cells. During visible light exposure, WO3/Pt nanoparticles manufacture hydroxyl radicals, degrade organic compounds, use NADPH, trigger lipid peroxidation, promote lysosomal membrane disruption, promote the loss of reduced glutathione, and activate apoptosis. In a model of advanced breast cancer metastasis to the eye’s anterior chamber, we show that WO3/Pt nanoparticles prolong the survival of 4T1 tumor-bearing Balb/c mice. This new generation of inorganic photosensitizers do not photobleach, and therefore should provide an important therapeutic advance in photodynamic therapy. As biomimetic nanoparticles destroy targeted cells, they may be useful in treating ocular and other forms of cancer.

  9. Design and synthesis of hierarchical mesoporous WO3-MnO2 composite nanostructures on carbon cloth for high-performance supercapacitors

    Science.gov (United States)

    Shinde, Pragati A.; Lokhande, Vaibhav C.; Patil, Amar M.; Ji, Taeksoo; Lokhande, Chandrakant D.

    2017-12-01

    To enhance the energy density and power performance of supercapacitors, the rational design and synthesis of active electrode materials with hierarchical mesoporous structure is highly desired. In the present work, fabrication of high-performance hierarchical mesoporous WO3-MnO2 composite nanostructures on carbon cloth substrate via a facile hydrothermal method is reported. By varying the content of MnO2 in the composite, different WO3-MnO2 composite thin films are obtained. The formation of composite is confirmed by X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS) analyses. The Brunauer-Emmett-Teller (BET) analysis reveals maximum specific surface area of 153 m2 g-1. The optimized WO3-MnO2 composite electrode demonstrates remarkable electrochemical performance with high specific capacitance of 657 F g-1 at a scan rate of 5 mV s-1 and superior longterm cycling stability (92% capacity retention over 2000 CV cycles). Furthermore, symmetric flexible solid-state supercapacitor based on WO3-MnO2 electrodes has been fabricated. The device exhibits good electrochemical performance with maximum specific capacitance of 78 F g-1 at a scan rate of 5 mV s-1 and specific energy of 10.8 Wh kg-1 at a specific power of 0.65 kW kg-1. The improved electrochemical performance could be ascribed to the unique combination of multivalence WO3 and MnO2 nanostructures and synergistic effect between them

  10. Dissimilar mechanism of executing hole transfer by WO{sub 3} and MoO{sub 3} nanoparticles in organic solar cells

    Energy Technology Data Exchange (ETDEWEB)

    Park, Eung-Kyu; Kim, Jae-Hyoung; Kim, Ji-Hwan; Park, Min-Ho; Lee, Dong-Hoon; Kim, Yong-Sang, E-mail: yongsang@skku.edu

    2015-07-31

    We investigated the effect of metal oxide nanoparticles (NPs) in poly (3,4 ethylenedioxythiophence):poly (styrene-sulfonate) layer for the light harvestation in poly (3-hexylthiophene):[6,6]-pheny-C{sub 61}-butyric acid methyl ester organic solar cells. The role of tungsten trioxide nanoparticles (WO{sub 3}) and molybdenum trioxide nanoparticles (MoO{sub 3}) in enhancing the efficiency of solar cells was compared. Due to the difference in the energy band structure of the two nanoparticles, the WO{sub 3} NPs acted as a hole blocking layer, whereas MoO{sub 3} NPs helped in the hole transfer. The solar cell with WO{sub 3} NPs at 1.5 wt% concentration showed a power conversion efficiency of 4.22% under AM 1.5G illumination and the device blended with 2 wt% of MoO{sub 3} NPs showed a power conversion efficiency of 4.40%. We measured various electrical properties including, electrochemical impedance spectroscopy and recombination mechanisms using the light intensity dependent current–voltage measurement of organic solar cell. - Highlights: • An organic solar cell was fabricated with WO{sub 3} or MoO{sub 3} NPs mixed PEDOT:PSS layer. • The effects of metallic NPs in PEDOT:PSS light harvesting system was investigated. • WO{sub 3} NPs acted as a hole blocking layer and MoO{sub 3} NPs helped in hole transporting. • The MoO{sub 3} NPs gave higher performance, reduced charge recombination and low resistance.

  11. Numerical Study Of The Effects Of Preloading, Axial Loading And Concrete Shrinkage On Reinforced Concrete Elements Strengthened By Concrete Layers And Jackets

    International Nuclear Information System (INIS)

    Lampropoulos, A. P.; Dritsos, S. E.

    2008-01-01

    In this study, the technique of seismic strengthening existing reinforced concrete columns and beams using additional concrete layers and jackets is examined. The finite element method and the finite element program ATENA is used in this investigation. When a reinforced jacket or layer is being constructed around a column it is already preloaded due to existing service loads. This effect has been examined for different values of the axial load normalized to the strengthened column. The techniques of strengthening with a concrete jacket or a reinforced concrete layer on the compressive side of the column are examined. Another phenomenon that is examined in this study is the shrinkage of the new concrete of an additional layer used to strengthen an existing member. For this investigation, a simply supported beam with an additional reinforced concrete layer on the tensile side is examined. The results demonstrate that the effect of preloading is important when a reinforced concrete layer is being used with shear connectors between the old and the new reinforcement. It was also found that the shrinkage of the new concrete reduces the strength of the strengthened beam and induces an initial sliding between the old and the new concrete

  12. Highly efficient direct Z-scheme WO3/CdS-diethylenetriamine photocatalyst and its enhanced photocatalytic H2 evolution under visible light irradiation

    Science.gov (United States)

    Hu, Taiping; Li, Pengfei; Zhang, Jinfeng; Liang, Changhao; Dai, Kai

    2018-06-01

    Cadmium sulfide (CdS) has demonstrated great promise in artificial photocataytic hydrogen (H2) production. However, the serious photocorrosion hinders its effective interaction and real-life application. In this work, a typical direct Z-scheme WO3/CdS-diethylenetriamine (CdS-DETA) composite has been designed via facile in-situ solvothermal method, which exhibits excellent H2 production properties in visible light region. In this system, the inorganic-organic CdS-DETA nanobelts (NBs) possess enough active sites and large surface area for the encouraging nanojunction structure information. Furthermore, we also systematically calculated energy band structure and investigated charge transfer of the WO3/CdS-DETA by PL and photocurrent test, the results demonstrated that the suitable band gap matching between CdS-DETA and WO3 and high redox potential improve the separation of photogenerated holes and electrons, restraining intrinsic photocorrosion of CdS as well as improving the photocatalytic activity. 5%WO3/CdS-DETA presented the most outstanding H2 evolution rate (15522 μmol g-1 h-1), which is twice higher than that of pure CdS-DETA. WO3/CdS-DETA composites also presented high stability after three recycle H2 production experiment. Finally, direct Z-scheme photocatalytic mechanism is calculated.

  13. Offshore concrete structures

    International Nuclear Information System (INIS)

    Lamas Pardo, M.; Carral Couce, L. M.

    2011-01-01

    In the offshore industry there are two possible materials for the construction of the hull of a structure; the steel and concrete, with the first one widely used until now, as in the rest of the shiphuidling industry of merchant ships, warships, etc. Materials such as aluminum, GRP or timber areused in small units with lengths lower than 100 m, and in less adverse conditions than in the offshore industry. Nevertheless, some ships/barges have been built of concrete in the past, but have been rather isolated cases which have not changed the practice in the industry. In the First and Second World War were built by the scarcity of materials, while the series of barges by Alfred A. Yee was a rare exception. Other units were also made in concrete, but almost anecdotal. Still, the behaviour of these concrete structures, especially in terms of maintenance, has been excellent. Therefore, the fact that the concrete has not had an adequate reception so far in shipbuilding, does not mean that in will not be the material best suited for the offshore industry in the future. The extra displacement and associated fuel costs in concrete ships have been found prohibitive in the past. But the loss of mobility of a concrete hull in relation to a steel hull can be perfectly offset by the advantages offered by the concrete, as the shipping and offshore industry have very different priorities. One of the main differences in these priorities is in terms of maintenance and resistance to fatigue, precisely where the concrete performs better. ships can easily be dry docked for maintenance and repair, while in the offshore platforms these works have to be done in situ so maintenance and fatigue are crucial to them. Besides these, the concrete has other advantages according to findings of several studies. And although they are interested in the conclusions that the makes as they came from people in the concrete industry, the fact that in recent years concrete offshore unit shave been built

  14. Self-compacting concrete (SCC)

    DEFF Research Database (Denmark)

    Geiker, Mette Rica

    2008-01-01

    In many aspects Self-Compacting Concrete (SCC, “Self-Consolidating Concrete” in North America) can be considered the concrete of the future. SCC is a family of tailored concretes with special engineered properties in the fresh state. SCC flows into the formwork and around even complicated...... reinforcement arrangements under its own weight. Thus, SCC is not vibrated like conventional concrete. This drastically improves the working environment during construction, the productivity, and potentially improves the homogeneity and quality of the concrete. In addition SCC provides larger architectural...

  15. Gasochromic performance of WO{sub 3}-nanorod thin films fabricated with an ArF excimer laser

    Energy Technology Data Exchange (ETDEWEB)

    Yaacob, M. H. [RMIT University, Melbourne (Australia); Universiti Putra Malaysia, Selangor (Malaysia); Ou, J. Z.; Wlodarski, W. [RMIT University, Melbourne (Australia); Kim, C. S.; Lee, J. Y. [KAIST, Daejon (Korea, Republic of); Kim, Y. H. [KIST, Seoul (Korea, Republic of); Oh, C. M.; Dhakal, K. P.; Kim, J. Y.; Kang, J. H. [University of Incheon, Incheon (Korea, Republic of)

    2012-02-15

    Thin films with tungsten trioxide (WO{sub 3}) nanorods were fabricated by using an ArF pulsed laser deposition system. Because the ArF excimer laser operates at a very short wavelength of 193 nm, short enough to expect strong absorption of the photons in the semiconductor oxide targets, and because the clusters incoming to the substrates have high momentum, we could build thin films with good surface morphology. Highly homogeneous arrays of nanorods with sizes mostly in the range of 30 - 40 nm were observed. The absorbance response towards hydrogen (H{sub 2}) gas was investigated for a WO{sub 3} film coated with 25-A-thick palladium (Pd). The Pd/WO{sub 3}-nanorod thin films exhibited excellent gasochromic response when measured in the visible-NIR range (400 - 1000 nm). As low as 0.06% H{sub 2} concentration was clearly sensed. A significant reversible absorbance change and fast recovery (<2 min) were observed when the films were exposed to H{sub 2} at different concentrations.

  16. Radiopurity of CaWO{sub 4} crystals for direct dark matter search with CRESST and EURECA

    Energy Technology Data Exchange (ETDEWEB)

    Muenster, Andrea [Physik Department E15, Technische Universitaet Muenchen, 85748 Garching (Germany); Collaboration: CRESST-Collaboration

    2015-07-01

    The direct dark matter search experiment CRESST uses scintillating CaWO{sub 4} single crystals as targets for possible WIMP recoils. A particle interaction in the crystal produces phonons as well as scintillation light. As the light signal is dependent on the kind of interacting particle, e{sup -}-recoils and α-decays mainly originating from intrinsic impurities of the crystal can be discriminated from nuclear recoils (e.g. due to possible WIMP scatterings). To achieve the best possible discrimination a high light output and a high radiopurity of the crystals are crucial. Since 2011 CaWO{sub 4} crystals are grown in the crystal lab of TU Munich. In this way we can directly influence the growth parameters and find a method to improve light output and radiopurity which is required by CRESST and the future tonne-scale multi-material experiment EURECA. In this talk we will discuss the investigated radiopurity of the raw materials WO{sub 3} and CaCO{sub 3} as well as of TUM-grown crystals which are currently taking data in CRESST II Phase 2.

  17. Mieszkanie poetyckie – koncepcja twórczości Władysława Wołkowskiego

    Directory of Open Access Journals (Sweden)

    Anna Wywioł

    2015-05-01

    Full Text Available The concept of work by Wladyslaw Wołkowski is mainly based on the notion of poetic flat. He called for the nature to be used within the flat and the nature’s language to be transformed into its interior. The author’s anthropocentric attitude could be found in every, even the smallest project. The furniture and elements of decoration were supposed to serve the human in a best possible way, both because of its usefulness and its visual, symbolic and finally spiritual values. The piece of art, beside its beauty and usefulness, has to possess the elements of the era during which it was created and the author’s national identity expressed by history, literature, legends and fairy tales. The art, according to the poet, should aspire to unify the outer world with his inner state, assuming that it can influence such state. Wołkowski created modular materials in accordance with rhythmic and harmonic constructions. Harmonic merger of an individual with community – according to Wołkowski – is the guarantee of wellbeing and calmness of spirit.

  18. Structural and optical properties of crystalline and nanocrystalline NaIn(WO4)2:Cr3+

    International Nuclear Information System (INIS)

    Fuks, H.; Skibiński, T.; Kaczmarek, S.M.; Hanuza, J.; Leniec, G.; Hermanowicz, K.; Mączka, M.; Ptak, M.

    2014-01-01

    Highlights: • Optical properties are summarized for single crystals and nanopowders of NaIn(WO 4 ) 2 :Cr. • EPR properties are compared in terms of different site occupation of Cr ion in the NaIn(WO 4 ) 2 matrix. • The changes in the PL and ESR properties of the nanopowders vs. their decreasing size are studied. • An increase of isolated ions with temperature at the expense of chromium complexes is observed. • Magnetic susceptibility and moment of the powders are discussed in terms of Cr substitution. -- Abstract: EPR and optical spectra of chromium doped NaIn(WO 4 ) 2 single crystals and nanopowders have been measured. The resonance EPR measurements have been performed for two crystal orientations in respect to the magnetic field and analyzed in terms of various Cr 3+ ion site occupancies in the crystal lattice. They have been structurally and optically identified. The changes in the photoluminescence and electron spin resonance properties of the nanoparticles vs. their decreasing size have also been studied. Magnetic susceptibility and effective magnetic moment of the nanopowders were measured and discussed in terms of chromium substitution. Comparisons between chromium substitution in single crystals and nanopowders have been performed

  19. Photocatalyticpaving concrete

    Directory of Open Access Journals (Sweden)

    Lyapidevskaya Ol'ga Borisovna

    2014-02-01

    Full Text Available Today bituminous concrete is a conventional paving material. Among its advantages one can name dustlessness and noiselessness, fine wear (up to 1 mm a year and fine maintainability. As the main disadvantages of this material one can name high slipperiness under humidification, low durability and weather resistance. Besides that, during placement of the bituminous concrete a lot of different air pollutants are emitted, which are harmful for environment and human’s health (they are listed in the paper according to the US Environmental Protection Agency materials. As an alternative, one can use cement-concrete pavement, which is in many ways more efficient than the bituminous concrete. It is proposed to enhance environmental performance of the cement-concrete pavement via usage of photocatalysis. The mechanism of different photocatalytic reactions is described in the paper, namely heterogeneous and homogeneous photocatalysis, photo-induces, photoactivated catalysis and catalytical photoreactions. It is pro-posed to use heterogeneous photocatalysis with titanium dioxide as a photocatalyst. The mechanism of photo oxidation of air contaminants, with the usage of titanium dioxide is2described. The paper sets problems, connected with the sensibilization of TiOto thevisible light (it is proposed to use titanium dioxide, doped with the atoms of certain elements to increase its sensibility to the visible light and with the development of a new photocatalytic paving concrete, which will meet the requirements, specified for paving in the climatic and traffic conditions of the Russian Federation.

  20. Fibre-concrete container

    International Nuclear Information System (INIS)

    2000-01-01

    In this leaflet the fibre-concrete container for radioactive wastes is described. The fibre container is made of fibre-concrete that contains cement, aggregate, sand, filter, flame-silica, super-plastificator, water and scattered metal fibres. The fibre-concrete container has a dice shape with outer dimension 1.7 x 1.7 x 1.7 m. It is mounted of a container body, a container cover and two caps. Total weight of container is 4,240 kg, maximum weight of loaded container do not must exceed 15,000 kg. The physical and mechanical properties of the fibre-concrete container are described in detail. The fibre-concrete container manufactured for storing of low and intermediate radioactive wastes. A fibre-concrete container utilization to store of radioactive wastes solves these problems: increase of stability of stored packages of radioactive waste; watertightness within 300 years at least; static stability of bearing space; better utilization of bearing spaces; insulation of radioactive waste in a case of seismic and geological event; increase of fire resistance; and transport of radioactive waste

  1. Very heavy iron-punching concretes

    International Nuclear Information System (INIS)

    Dubois, F.

    1966-01-01

    The present report deals with all the heavy iron-punching concretes, metallic wastes produced by the transformation industry. After a detailed description of the physical properties of metallic aggregates, a classification of heavy mortars is given, into three main categories: steel-shot grouts d = 5,3 - 6; steel-shot grouts mixed with a mineral d = 3,7 - 4,2; injection heavy grouts d = 3,5 - 4. The following chapter describes iron-punching concretes the most used in the atomic industry: iron-punching concretes mixed with cast-iron - iron-punching concretes mixed with magnetite; iron-punching concretes mixed with barite; iron-punching concretes mixed with limonite; iron-punching concretes mixed with boron. The compositions of these concretes are given together with their physical and mechanical characteristics. Numerous diagrams make it possible to find rapidly the proportions of the constituents of these concretes as a function of the required density. Technical advice and specifications are given in an appendix together with a bibliography of these heavy concretes. (author) [fr

  2. Synthesis and characterization of WO3 nanostructures prepared by an aged-hydrothermal method

    International Nuclear Information System (INIS)

    Huirache-Acuna, R.; Paraguay-Delgado, F.; Albiter, M.A.; Lara-Romero, J.; Martinez-Sanchez, R.

    2009-01-01

    Nanostructures of tungsten trioxide (WO 3 ) have been successfully synthesized by using an aged route at low temperature (60 deg. C) followed by a hydrothermal method at 200 deg. C for 48 h under well controlled conditions. The material was studied by X-ray diffraction (XRD), scanning electron microscopy (SEM) and Energy Dispersive Spectroscopy (EDS), transmission electron microscopy (TEM) and high-resolution transmission electron microscopy (HRTEM), Raman spectroscopy and X-ray photoelectron spectroscopy (XPS). Specific Surface Area (S BET ) were measured by using the BET method. The lengths of the WO 3 nanostructures obtained are between 30 and 200 nm and their diameters are from 20 to 70 nm. The growth direction of the tungsten oxide nanostructures was determined along [010] axis with an inter-planar distance of 0.38 nm.

  3. Improved genetic algorithms using inverse-elitism; Gyakuerito senryaku wo mochiita kairyo identeki algorithm

    Energy Technology Data Exchange (ETDEWEB)

    Kawanishi, H.; Hagiwara, M. [Keio University, Tokyo (Japan)

    1998-05-01

    Improved Genetic Algorithms (GAs) have been proposed in this paper. We have directed our attention to `selection` and `crossover` in GAs. Novel strategies in selection and crossover are used in the proposed method. Various selecting strategies have been used in the conventional GAs such as Elitism, Tournament, Ranking, Roulette wheel, and Expected value model. These are not always effective, since these refer to only the fitness of each chromosome. We have developed the following techniques to improve the conventional GAs: `inverse-elitism` as a selecting strategy and variable crossover range as a crossover strategy. In the `inverse-elitism`, an inverse-elite whose gene values are reversed from those in the corresponding elite is produced. This strategy greatly contributes to diversification of chromosomes. As for the variable crossover range, we combine the following crossover techniques effectively: one is that range in crossover is varied from wide to narrow gradually to carry out global search in the beginning and local search in the ending; another is that range in crossover is varied from narrow to wide. We confirmed validity and superior performance of the proposed method by computer simulations. 18 refs., 9 figs., 3 tabs.

  4. Shallow PS-logging by high frequency wave; Koshuha wo mochiita senbu PS kenso

    Energy Technology Data Exchange (ETDEWEB)

    Nakajima, A; Miyazawa, M; Azuma, H [OYO Corp., Tokyo (Japan)

    1996-05-01

    This paper describes the following matters on down-hole PS logging in shallow subsurface. Determining an elastic wave velocity structure in shallow subsurface with high accuracy by using down-hole PS logging requires reduction of errors in reading travel time. Therefore, a high-frequency vibration source was fabricated with an objective to raise frequencies of waves used for the measurement. Measurements were made on two holes, A and B, at a measurement interval of 0.5 m, whereas at the hole A a measurement was performed simultaneously by using a normal type (low-frequency) vibration source. A spectral analysis on the waveform record revealed that the frequencies with each vibration source were 127 Hz and 27 Hz for the hole A, 115 Hz for the hole B, and the S/N ratio was all the same for both holes. When the high-frequency vibration source was used, the velocity was determined at accuracy of 5% over the whole length of the shallow section. When the low-frequency vibration source was used, sections with the velocity determining error greater than 5% were found, and it was not possible to derive the velocity structure in the shallow subsurface in fine segments. 3 refs., 8 figs., 2 tabs.

  5. Reservoir characterization using artificial neural network; Neural network wo mochiita choryuso tokusei kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    Shimada, N; Kozawa, T [Japan National Oil Corp., Tokyo (Japan); Nishikawa, N; Tani, A [Fuji Research Institute Corp., Tokyo (Japan)

    1997-05-27

    Neural network is used for the prediction of porosity and permeability using logging data as reservoir characteristics, and the validity of this method is verified. For the prediction of reservoir characteristics by the use of seismic survey data, composite seismic survey records obtained by density logging and acoustic logging are used to experiment the prediction of porosity and permeability continuous along lines of wells. A 3-output back propagation network is used for analysis. There is a possibility that this technique when optimized will improve on prediction accuracy. Furthermore, in the case of characteristics mapping, 3-dimensional seismic data is applied to a carbonate rock reservoir for predicting spatial porosity and permeability. This technique facilitates the comprehensive analysis of core data, well data, and seismic survey data, enabling the derivation of a high-precision spatial distribution of reservoir characteristics. Efforts will continue for further improvement on prediction accuracy. 6 refs., 7 figs., 3 tabs.

  6. Trial to active seismic while drilling; Jinko shingen wo mochiita SWD eno kokoromi

    Energy Technology Data Exchange (ETDEWEB)

    Tsuru, T; Kozawa, T [Japan National Oil Corp., Tokyo (Japan). Technology Research Center

    1996-10-01

    This paper describes the development of a more stable SWD system with larger energy by adding an artificial seismic source near the bit. SWD is a technique by which the seismic wave generated while drilling of rocks by bit can be observed on the ground surface and the records equivalent to the reverse VSP can be obtained. For this system, a shell with a vibrator was fixed immediately on the bit as a sub-generator, and total energy of usual impact by the bit and vibration by the vibrator was used as a seismic source for SWD. For the seismic wave generation mechanism of this vibrator, the shell was resonated by the magnetostrictive element, and vibration was given to the bit and drilling pipe. When this seismic source is used, only single frequency is obtained for each vibration due to the utilization of resonance of shell. Therefore, the generation patterns should be made, by which wide band energy can be obtained after the interaction. Since the survey was conducted using this bottom hole seismic source at the drilling depth more than 3,000 m, it was necessary to enhance the vibration energy. 2 refs., 2 figs.

  7. Biodegradable polymeric foam with food waste; Shokumotsu zansa wo mochiita seibunkai kobunshi hahhotai

    Energy Technology Data Exchange (ETDEWEB)

    Mishima, Kenji; Matsuyama, Kiyoshi; Yamauchi, Satoru; Takarabe, Shin' ichi

    1999-09-01

    A huge amount of food waste such as tea and beer dregs becomes a serious problem because of the lack of industrial waste space in Japan. On the other hand, the new polymeric foam is expected to be developed since the dangerous pollution of endorphin disrupters from industrial polymer foam is pointed out. In this work, we try to develop the biodegradable polymeric foam using the tea and beer dregs as secondary resources. And we examined the degradability of biodegradable polymer in the hydrothermal water for fundamental knowledge of polymeric foam production. We used an extruder equipped with a high pressure device to make the polymeric foam. And we examined the effect of the component ratio on the foam properties, foaming rate, strength, shrinkage rate, water-resistant. As a result, it was found that the amount of polymer is effective of quality of form and the biodegradability can be controlled by the amount of water and temperature. (author)

  8. Acrylonitrile butadiene rubber (NBR)/manganous tungstate (MnWO4) nanocomposites: Characterization, mechanical and electrical properties

    Science.gov (United States)

    Ramesan, M. T.; Abdu Raheem V., P.; Jayakrishnan, P.; Pradyumnan, P. P.

    2014-10-01

    Nanocomposites of NBR with manganous-tungstate nanoparticles were prepared through vulcanization process. The extent of interaction of nanoparticles with the polymer was studied by FTIR, SEM, XRD, TGA and AC conductivity. FTIR and XRD ascertain the interaction of NBR with MnWO4 nanoparticles. SEM analysis established that the nanopartilces were well dispersed in the macromolecular chain of NBR. The mechanical properties of the nanocomposites were studied as a function of filler loading. The nanocomposites exhibited enhanced thermal stability as seen in TGA. Conductivity and dielectric properties of nanocomposites increase with increase in concentration of MnWO4 nanoparticles (7phr) and thereafter the value decreases.

  9. Increased Durability of Concrete Made with Fine Recycled Concrete Aggregates Using Superplasticizers.

    Science.gov (United States)

    Cartuxo, Francisco; de Brito, Jorge; Evangelista, Luis; Jiménez, José Ramón; Ledesma, Enrique F

    2016-02-08

    This paper evaluates the influence of two superplasticizers (SP) on the durability properties of concrete made with fine recycled concrete aggregate (FRCA). For this purpose, three families of concrete were tested: concrete without SP, concrete made with a regular superplasticizer and concrete made with a high-performance superplasticizer. Five volumetric replacement ratios of natural sand by FRCA were tested: 0%, 10%, 30%, 50% and 100%. Two natural gravels were used as coarse aggregates. All mixes had the same particle size distribution, cement content and amount of superplasticizer. The w/c ratio was calibrated to obtain similar slump. The results showed that the incorporation of FRCA increased the water absorption by immersion, the water absorption by capillary action, the carbonation depth and the chloride migration coefficient, while the use of superplasticizers highly improved these properties. The incorporation of FRCA jeopardized the SP's effectiveness. This research demonstrated that, from a durability point of view, the simultaneous incorporation of FRCA and high-performance SP is a viable sustainable solution for structural concrete production.

  10. Ethanol vapour sensing properties of screen printed WO 3 thick films

    Indian Academy of Sciences (India)

    The ethanol vapour sensing properties of these thick films were investigated at different operating temperatures and ethanol vapour concentrations. The WO3 thick films exhibit excellent ethanol vapour sensing properties with a maximum sensitivity of ∼1424.6% at 400°C in air atmosphere with fast response and recovery ...

  11. Impact of recycled gravel obtained from low or medium concrete grade on concrete properties

    Directory of Open Access Journals (Sweden)

    Yasser Abdelghany Fawzy

    2018-04-01

    Full Text Available This paper investigates the effect of recycled gravel obtained from low (Gl or medium (Gm concrete grade on fresh property of concrete (slump, mechanical properties (compressive-splitting tensile strength and mass transport properties (ISAT-sorptivity of concrete containing dolomite as a natural coarse aggregate. Concrete specimens were prepared with cement, water, sand and dolomite admixed with recycled gravel. The percentage of recycled gravel/dolomite was 0:100, 25:75, 50:50 and 75:25 at w/c = 0.50, 0.55 and 0.60. The effect of silica fume and bonding admixture at w/c = 0.55 on concrete properties were also considered. The results indicated that, increasing the percentage of recycled gravel/dolomite led to decreasing the slump. All mechanical properties of concrete discussed were inversely affected by increasing percentage of recycled gravel/dolomite from low and medium concrete. Adding 10% SF or bonding admixture increased the mechanical properties of concrete. Mass transport properties of concrete (ISAT-sorptivity were enhanced by decreasing the percentage of recycled gravel/dolomite. The optimum percentage of recycled gravel/dolomite = 25%. Keywords: Recycled gravel, Concrete, Silica fume, Compressive strength, Mass transport

  12. One-pot synthesis and photoluminescence properties of core/porous-shell olive-like BaWO4 microstructure by a template-assisted hydrothermal method

    Science.gov (United States)

    Zhang, Suyue; Wang, Yunlong; Wang, Cuiping; Zhang, Hui; Shen, Yuhua; Xie, Anjian

    2016-02-01

    Core/porous-shell olive-like crystalline BaWO4 is synthesized by a combined simple hydrothermal method and soft template approach. The prepared product shows an olive-like shape with diameter of ˜2 μm, length of ˜4 μm, and the thickness of the shell of about 65 nm, which are orderly assembled by many nanoparticles. A possible formation mechanism of olive-like BaWO4 microstructure involving interfacial recognization of ions, nucleation, aggregation, in situ growth and Ostwald ripening process is proposed. Polyacrylic acid sodium (PAAS) as a template plays an important role in inducing the nucleation and growth of olive-like BaWO4 microcrystalline. Other shapes of BaWO4 microcrystalline are also fabricated by varying the concentration of PAAS and Ba2+. The olive-like product with a core-shell structure which exists a large number of pores on crystal surface shows excellent photoluminescence property, which have potentially applied prospects in fields such as light display systems etc.

  13. Oil encapsulation in core-shell alginate capsules by inverse gelation II: comparison between dripping techniques using W/O or O/W emulsions.

    Science.gov (United States)

    Martins, Evandro; Poncelet, Denis; Rodrigues, Ramila Cristiane; Renard, Denis

    2017-09-01

    In the first part of this article, it was described an innovative method of oil encapsulation from dripping-inverse gelation using water-in-oil (W/O) emulsions. It was noticed that the method of oil encapsulation was quite different depending on the emulsion type (W/O or oil-in-water (O/W)) used and that the emulsion structure (W/O or O/W) had a high impact on the dripping technique and the capsules characteristics. The objective of this article was to elucidate the differences between the dripping techniques using both emulsions and compare the capsule properties (mechanical resistance and release of actives). The oil encapsulation using O/W emulsions was easier to perform and did not require the use of emulsion destabilisers. However, capsules produced from W/O emulsions were more resistant to compression and showed the slower release of actives over time. The findings detailed here widened the knowledge of the inverse gelation and gave opportunities to develop new techniques of oil encapsulation.

  14. Radiation Damage Mechanism in PbWO4 Crystal and Radiation Hardness Quality Control of PWO Scintillators for CMS

    CERN Document Server

    Baccaro, Stefania; Borgia, Bruno; Cavallari, Francesca; Cecilia, Angelica; Dafinei, Ioan; Diemoz, Marcella; Lecoq, Paul; Longo, Egidio; Montecchi, Marco; Organtini, Giovanni; Salvatori, S

    1997-01-01

    The optical damage induced by UV light in PbWO4 crystals is found to be similar to that induced by g radiation. Due to the peculiarities of optical absorption in PbWO4, the damage induced by UV light is a bulk process. This fact has important consequences for the approach to be adopted both for the use of the crystal as scintillator and for the qualification methods foreseen in the Regional Centres of the ECAL CMS Collaboration.

  15. Fabrication of the heterostructured CsTaWO{sub 6}/Au/g-C{sub 3}N{sub 4} hybrid photocatalyst with enhanced performance of photocatalytic hydrogen production from water

    Energy Technology Data Exchange (ETDEWEB)

    Lang, Junyu; Liu, Mengqing; Su, Yiguo; Yan, Lijuan; Wang, Xiaojing, E-mail: wang_xiao_jing@hotmail.com

    2015-12-15

    Graphical abstract: - Highlights: • A novel ternary CsTaWO{sub 6}/Au/g-C{sub 3}N{sub 4} hybrid photocatalyst was successfully fabricated. • Au particles act as an electron-conduction bridge between the heterostructure. • The photoctalytic hydrogen generation was promoted by the SPR of the Au. • CsTaWO{sub 6}/Au/g-C{sub 3}N{sub 4} shows significant photocatalytic activity in H{sub 2} generation. - Abstract: In this work, a novel CsTaWO{sub 6}/Au/g-C{sub 3}N{sub 4} hybrid photocatalyst is successfully fabricated. The photocatalytic performance of the heterostructured CsTaWO{sub 6}/Au/g-C{sub 3}N{sub 4} composite was investigated. Au nanoparticles were photo-deposited as the interlayer between g-C{sub 3}N{sub 4} and the surface of CsTaWO{sub 6}, which can facilitate the photoinduced electrons migration as an electron-conduction bridge as well as increase visible-light absorption via the surface plasmon resonance. This heterostructured interface bridging by Au particles may significantly retard the recombination of electron–holes, which is beneficial to promote the photocatalytic activity under visible-light irradiation. It is found the CsTaWO{sub 6}/Au/g-C{sub 3}N{sub 4} sample showed excellent photocatalytic activity of water splitting, even higher than the sum of g-C{sub 3}N{sub 4} and Au/CsTaWO{sub 6} samples, or the sum of CsTaWO{sub 6} and Au/g-C{sub 3}N{sub 4} samples. It indicates that the heterostructured combination of g-C{sub 3}N{sub 4} and CsTaWO{sub 6} bridging by Au particles provided the synergistic photocatalytic activity driving by solar light through an efficient electron transfer process.

  16. Luminescence and photothermally stimulated defects creation processes in PbWO4:La3+, Y3+ (PWO II) crystals

    International Nuclear Information System (INIS)

    Auffray, E.; Korjik, M.; Zazubovich, S.

    2015-01-01

    Photoluminescence and thermally stimulated luminescence (TSL) are studied for a PbWO 4 crystal grown by the Czochralski method at Bogoroditsk Technical Chemical Plant, Russia from the melt with a precise tuning of the stoichiometry and co-doped with La 3+ and Y 3+ ions (the PWO II crystal). Photothermally stimulated processes of electron and hole centers creation under selective UV irradiation of this crystal in the 3.5–5.0 eV energy range and the 85–205 K temperature range are clarified and the optically created electron and hole centers are identified. The electrons in PWO II are mainly trapped at the (WO 4 ) 2− groups located close to single La 3+ and Y 3+ ions, producing the electron {(WO 4 ) 3− –La 3+ } and {(WO 4 ) 3− –Y 3+ } centers. The holes are mainly trapped at the regular oxygen ions O 2− located close to La 3+ and Y 3+ ions associated with lead vacancies, producing the hole O − (I)-type centers. No evidence of single-vacancy-related centers has been observed in PWO II. The data obtained indicate that excellent scintillation characteristics of the PWO II crystal can be explained by a negligible concentration of single (non-compensated) oxygen and lead vacancies as the traps for electrons and holes, respectively. - Highlights: • Photoluminescence of the PbWO 4 :La 3+ , Y 3+ (PWO II) crystal is investigated. • Creation of defects under UV irradiation of PWO II is studied by TSL. • Origin of dominating electron and hole centers is ascertained. • Concentration of single-vacancy-related centers is found to be negligible. • Excellent scintillation characteristics of the PWO II crystal are explained.

  17. Concrete construction engineering handbook

    CERN Document Server

    Nawy, Edward G

    2008-01-01

    Provides coverage of concrete construction engineering and technology. This work features discussions focusing on: the advances in engineered concrete materials; reinforced concrete construction; specialized construction techniques; and, design recommendations for high performance.

  18. A low cost preparation of WO3 nanospheres film with improved thermal stability of gasochromic and its application in smart windows

    Science.gov (United States)

    Zhou, Baoyu; Feng, Wei; Gao, Guohua; Wu, Guangming; Chen, Yue; Li, Wen

    2017-11-01

    Porous WO3 nanospheres film was successfully synthesized by employing a low-cost and facile template-assisted sol-gel method. The effects of template agent (Pluronic F127) on structure, morphology and specific surface area were systematically studied by Fourier transform infrared (FTIR), x-ray diffraction (XRD), transmission electron microscopy (TEM), scanning electron microscopy (SEM), and N2 physisorption. It was found that F127 played a significant role in governing the morphology of WO3 sol clusters, and the optimal post-processing for ‘naked’ WO3 nanospheres film is acetone extraction and subsequent annealing treatment at 350 °C. As anticipated, the relative fast coloring/bleaching rates of WO3 nanospheres film are believed to be the results of porous microstructure and nanocrystalline, where provides much surface active position (166 m2 g-1) and shortens the proton diffusion distance. We believe that this unique approach to synthesize nanospheres structure may has beneficial effects on applications which also are based on insertion/extraction and diffusion abilities, such as supercapacitor, batteries and gas sensors.

  19. Comparison of physical and mechanical properties of river sand concrete with quarry dust concrete

    Science.gov (United States)

    Opara, Hyginus E.; Eziefula, Uchechi G.; Eziefula, Bennett I.

    2018-03-01

    This study compared the physical and mechanical properties of river sand concrete with quarry dust concrete. The constituent materials were batched by weight. The water-cement ratio and mix ratio selected for the experimental investigation were 0.55 and 1:2:4, respectively. The specimens were cured for 7, 14, 21 and 28 days. Slump, density and compressive strength tests were carried out. The results showed that river sand concrete had greater density and compressive strength than quarry dust concrete for all curing ages. At 28 days of curing, river sand concrete exceeded the target compressive strength by 36%, whereas quarry dust concrete was less than the target compressive strength by 12%. Both river sand concrete and quarry dust concrete for the selected water/cement ratio and mix ratio are suitable for non-structural applications and lightly-loaded members where high strength is not a prerequisite.

  20. Human parvovirus B19 antibodies induce altered membrane protein expression and apoptosis of BeWo trophoblasts.

    Science.gov (United States)

    Tzang, Bor-Show; Chiang, Szu-Yi; Chan, Hsu-Chin; Liu, Chung-Hsien; Hsu, Tsai-Ching

    2016-11-01

    Human parvovirus B19 (B19) is harmful during pregnancy since it can be vertically transmitted to the developing fetus. In addition, the anti‑B19 antibodies induced by B19 infection are believed to have a cytopathic role in B19 transmission; however, knowledge regarding the effects of anti‑B19 antibodies during pregnancy is limited. To investigate the possible roles of anti‑B19 antibodies during pregnancy, the present study examined the effects of anti‑B19‑VP1 unique region (VP1u), anti‑B19‑VP2 and anti‑B19‑nonstructural protein 1 (NS1) immunoglobulin G (IgG) antibodies on BeWo trophoblasts. Briefly, BeWo trophoblasts were incubated with purified IgG against B19‑VP1u, B19‑VP2 and B19‑NS1. Subsequently, the expression of surface proteins and apoptotic molecules were assessed in BeWo trophoblasts using flow cytometry, ELISA and western blotting. The expression levels of human leukocyte antigen (HLA)‑G were significantly increased on BeWo trophoblasts treated with rabbit anti‑B19‑VP1u IgG, and were unchanged in those treated with rabbit anti‑B19‑NS1 and anti‑B19‑VP2 IgG, as compared with the control group. Furthermore, the expression levels of globoside (P blood group antigen) and cluster of differentiation (CD)29 (β1 integrin) were significantly increased in BeWo trophoblasts treated with rabbit anti‑B19‑NS1 and anti‑B19‑VP2 IgG, whereas only CD29 was also significantly increased in cells treated with anti‑B19‑VP1u IgG. In addition, the number of cells at sub‑G1 phase; caspase‑3 activity; and the expression of intrinsic and extrinsic apoptotic molecules, including Fas‑associated death domain protein, activated caspase‑8, activated caspase‑3, B‑cell lymphoma 2‑associated X protein, cytochrome c, apoptotic peptidase activating factor 1 and activated caspase‑9, were significantly increased in BeWo trophoblasts treated with anti‑B19‑VP1u and anti‑B19‑NS1 IgG. In conclusion, the present