WorldWideScience

Sample records for wisconsin architecture industrial

  1. Skill Needs and Training Strategies in the Wisconsin Printing Industry.

    Science.gov (United States)

    Wisconsin Univ., Madison. Center on Wisconsin Strategy.

    A study examined the emerging skill needs in the Wisconsin printing industry, a key industry that provided the largest increase (more than 13,000 new jobs) in manufacturing employment in the state in the past decade. Eighteen interviews were conducted with industry personnel and production managers, union representatives, technical college…

  2. Hazardous emissions, operating practices, and air regulations at industrial wood-fired facilities in Wisconsin

    International Nuclear Information System (INIS)

    Hubbard, A.J.

    1993-01-01

    Since October of 1988 the State of Wisconsin Department of Natural Resources has regulated over four hundred substances as hazardous air pollutants. The rule regulates new as well as existing sources of air pollution in Wisconsin. Consequently, all permits to operate an air pollution source in Wisconsin must address the hazardous air emissions potential of the source. While widely perceived as a clean-burning fuel, wood is often burned in a manner which clearly results in significant emissions of very hazardous air pollutants. Research conducted on a 20 million BTU per hour wood-fired spreader stoker boiler in northern Wisconsin showed that this boiler has the potential to emit 0.022 pound of benzene and 0.012 pound of formaldehyde per ton (lb/ton) of wood fired. Recent stack tests at more than a dozen other small industrial wood-fired facilities in Wisconsin show a range of formaldehyde emissions of 0.0007--0.1950 lb/ton. Work at Birchwood Lumber ampersand Veneer showed that the benzene and formaldehyde emission rates under good firing conditions are an order of magnitude lower than the benzene and formaldehyde emission rates under poor firing conditions. This finding has supported Wisconsin's regulatory approach of encouraging wood-fired facilities to enhance the quality of the combustion process as a technique to minimize the hazardous air pollution potential of industrial wood combustion. The Wisconsin strategy is to define open-quotes good combustion technologyclose quotes through easily measurable combustion parameters rather than emission standards. This paper presents several techniques in use in Wisconsin to comply with open-quotes good combustion technologyclose quotes for industrial wood-fired furnaces. These techniques include fuel blending overfire air, furnace insulation, and proper grate design

  3. Future demands for an Industrialized Architecture?

    DEFF Research Database (Denmark)

    Beim, Anne

    2011-01-01

    When speaking about the future demands for industrialized architecture – or how to translate industrialized processes into tectonic sustainable design strategies in architecture – several questions come to mind. First of all, why is the building industry in comparison to the production industry...... these questions raise a wide-spread discussion, one could argue that the building industry can benefit from different ways of architectural synthesis thinking as a basis for improving. This understood in such a way that industrialized manufacturing technologies and products should be driven by ideas...

  4. The changing veneer and plywood industry of Michigan and Wisconsin.

    Science.gov (United States)

    Gary R. Lindell; Lewis T. Hendricks

    1972-01-01

    Analyzes trends in the hardwood veneer and plywood industry of Michigan and Wisconsin between 1964 and 1969. In that period, red oak and hard maple replaced yellow birch as the major species used. Log supplies were adequate. Wall paneling was the major end market with doorskins next. Excess plywood producing capacity is a chronic problem.

  5. Architectural freedom and industrialized architecture

    DEFF Research Database (Denmark)

    Vestergaard, Inge

    2012-01-01

    to explain that architecture can be thought as a complex and diverse design through customization, telling exactly the revitalized storey about the change to a contemporary sustainable and better performing expression in direct relation to the given context. Through the last couple of years we have...... proportions, to organize the process on site choosing either one room wall components or several rooms wall components – either horizontally or vertically. Combined with the seamless joint the playing with these possibilities the new industrialized architecture can deliver variations in choice of solutions...... for retrofit design. If we add the question of the installations e.g. ventilation to this systematic thinking of building technique we get a diverse and functional architecture, thereby creating a new and clearer story telling about new and smart system based thinking behind architectural expression....

  6. Losses due to weather phenomena in the bituminous concrete construction industry in Wisconsin

    Science.gov (United States)

    Kuhn, H. A. J.

    1973-01-01

    The losses (costs) due to weather phenomena as they affect the bituminous concrete industry in Wisconsin were studied. The bituminous concrete industry's response to precipitation, in the form of rain, is identified through the use of a model, albeit crude, which identifies a typical industry decision-response mechanism. Using this mechanism, historical weather data and 1969 construction activity, dollar losses resulting from rain occurrences were developed.

  7. Tectonic thinking in contemporary industrialized architecture

    DEFF Research Database (Denmark)

    Beim, Anne

    2013-01-01

    a creative force in building constructions, structural features and architectural design (construing) – helps to identify and refine technology transfer in contemporary industrialized building construction’. Through various references from the construction industry, business theory and architectural practice......This paper argues for a new critical approach to the ways architectural design strategies are developing. Contemporary construction industry appears to evolve into highly specialized and optimized processes driven by industrialized manufacturing, therefore the role of the architect...... and the understanding of the architectural design process ought to be revised. The paper is based on the following underlying hypothesis: ‘Tectonic thinking – defined as a central attention towards the nature, the properties, and the application of building materials (construction) and how this attention forms...

  8. Wisconsin timber industry--an assessment of timber product output and use, 1988.

    Science.gov (United States)

    W. Brad Smith; James W. Whipple

    1990-01-01

    Discusses recent Wisconsin forest industry trends; production and receipts of pulpwood, saw logs, and veneer logs; and production of other timber products in 1988. Reports on logging residue, on wood and bark residue generated at primary wood-using mills, and on disposition of this mill residue.

  9. Architectural Prototyping in Industrial Practice

    DEFF Research Database (Denmark)

    Christensen, Henrik Bærbak; Hansen, Klaus Marius

    2008-01-01

    Architectural prototyping is the process of using executable code to investigate stakeholders’ software architecture concerns with respect to a system under development. Previous work has established this as a useful and cost-effective way of exploration and learning of the design space of a system......, in addressing issues regarding quality attributes, in addressing architectural risks, and in addressing the problem of knowledge transfer and conformance. Little work has been reported so far on the actual industrial use of architectural prototyping. In this paper, we report from an ethnographical study...... and focus group involving architects from four companies in which we have focused on architectural prototypes. Our findings conclude that architectural prototypes play an important role in resolving problems experimentally, but less so in exploring alternative solutions. Furthermore, architectural...

  10. Future demands for an Industrialized Architecture?

    DEFF Research Database (Denmark)

    Beim, Anne

    2011-01-01

    these questions raise a wide-spread discussion, one could argue that the building industry can benefit from different ways of architectural synthesis thinking as a basis for improving. This understood in such a way that industrialized manufacturing technologies and products should be driven by ideas...

  11. Wisconsin Inventors` Network Database final report

    Energy Technology Data Exchange (ETDEWEB)

    1991-12-04

    The Wisconsin Innovation Service Center at UW-Whitewater received a DOE grant to create an Inventor`s Network Database to assist independent inventors and entrepreneurs with new product development. Since 1980, the Wisconsin Innovation Service Center (WISC) at the University of Wisconsin-Whitewater has assisted independent and small business inventors in estimating the marketability of their new product ideas and inventions. The purpose of the WISC as an economic development entity is to encourage inventors who appear to have commercially viable inventions, based on preliminary market research, to invest in the next stages of development, perhaps investigating prototype development, legal protection, or more in-depth market research. To address inventor`s information needs, WISC developed on electronic database with search capabilities by geographic region and by product category/industry. It targets both public and private resources capable of, and interested in, working with individual and small business inventors. At present, the project includes resources in Wisconsin only.

  12. The Experimental Physics and Industrial Control System architecture: Past, present, and future

    International Nuclear Information System (INIS)

    Dalesio, L.R.; Hill, J.O.; Kraimer, M.; Lewis, S.; Murray, D.; Hunt, S.; Claussen, M.; Watson, W.

    1993-01-01

    The Experimental Physics and Industrial Control System (EPICS), has been used at a number of sites for performing data acquisition, supervisory control, closed-loop control, sequential control, and operational optimization. The EPICS architecture was originally developed by a group with diverse backgrounds in physics and industrial control. The current architecture represents one instance of the ''standard model.'' It provides distributed processing and communication from any LAN device to the front end controllers. This paper will present the genealogy, current architecture, performance envelope, current installations, and planned extensions for requirements not met by the current architecture

  13. Financial architecture and industrial technology: A co-evolutionary model

    NARCIS (Netherlands)

    Negriu, A.

    2013-01-01

    Empirical evidence points to a relation between the financial architecture of an economy and industrial technology: market-based financial systems support the development of industries where innovation is typically radical whereas incremental innovation thrives in association with bank-based

  14. Wisconsin Inventors' Network Database final report

    Energy Technology Data Exchange (ETDEWEB)

    1991-12-04

    The Wisconsin Innovation Service Center at UW-Whitewater received a DOE grant to create an Inventor's Network Database to assist independent inventors and entrepreneurs with new product development. Since 1980, the Wisconsin Innovation Service Center (WISC) at the University of Wisconsin-Whitewater has assisted independent and small business inventors in estimating the marketability of their new product ideas and inventions. The purpose of the WISC as an economic development entity is to encourage inventors who appear to have commercially viable inventions, based on preliminary market research, to invest in the next stages of development, perhaps investigating prototype development, legal protection, or more in-depth market research. To address inventor's information needs, WISC developed on electronic database with search capabilities by geographic region and by product category/industry. It targets both public and private resources capable of, and interested in, working with individual and small business inventors. At present, the project includes resources in Wisconsin only.

  15. Water Use in Wisconsin, 2005

    Science.gov (United States)

    Buchwald, Cheryl A.

    2009-01-01

    The U.S. Geological Survey (USGS) Wisconsin Water Science Center is responsible for presenting data collected or estimated for water withdrawals and diversions every 5 years to the National Water-Use Information Program (NWUIP). This program serves many purposes such as quantifying how much, where, and for what purpose water is used; tracking and documenting water-use trends and changes; and providing these data to other agencies to support hydrologic projects. In 2005, data at both the county and subbasin levels were compiled into the USGS national water-use database system; these data are published in a statewide summary report and a national circular. This publication, Water Use in Wisconsin, 2005, presents the water-use estimates for 2005; this publication also describes how these water-use data were determined (including assumptions used), limitations of using these data, and trends in water-use data presented to the NWUIP. Estimates of water use in Wisconsin indicate that about 8,608 million gallons per day (Mgal/d) were withdrawn during 2005. Of this amount, about 7,622 Mgal/d (89 percent) were from surface-water sources and about 986 Mgal/d (11 percent) were from ground-water sources. Surface water used for cooling at thermoelectric-power plants constituted the largest portion of daily use at 6,898 Mgal/d. Water provided by public-supply water utilities is the second largest use of water and totaled 552 Mgal/d. Public supply served approximately 71 percent of the estimated 2005 Wisconsin population of 5.54 million people; two counties - Milwaukee and Dane - accounted for more than one-third of the public-supply withdrawal. Industrial and irrigation were the next major water uses at 471 and 402 Mgal/d, respectively. Non-irrigational agricultural (livestock and aquaculture) accounted for approximately 155 Mgal/d and is similar to the combined withdrawal for the remaining water-use categories of domestic, commercial, and mining (131 Mgal/d). Data on water use

  16. Architectural freedom and industrialized architecture

    DEFF Research Database (Denmark)

    Vestergaard, Inge

    2012-01-01

    to explain that architecture can be thought as a complex and diverse design through customization, telling exactly the revitalized storey about the change to a contemporary sustainable and better performing expression in direct relation to the given context. Through the last couple of years we have...... expression in the specific housing area. It is the aim of this article to expand the different design strategies which architects can use – to give the individual project attitudes and designs with architectural quality. Through the customized component production it is possible to choose different...... for retrofit design. If we add the question of the installations e.g. ventilation to this systematic thinking of building technique we get a diverse and functional architecture, thereby creating a new and clearer story telling about new and smart system based thinking behind architectural expression....

  17. Design of management information system for nuclear industry architectural project costs

    International Nuclear Information System (INIS)

    Zhang Xingzhi; Li Wei

    1996-01-01

    Management Information System (MIS) for nuclear industry architectural project is analysed and designed in detail base on quota management and engineering budget management of nuclear industry in respect of the practice of Qinshan Second Phase 2 x 600 MW Project

  18. ADAPTIVE REUSE FOR NEW SOCIAL AND MUNICIPAL FUNCTIONS AS AN ACCEPTABLE APPROACH FOR CONSERVATION OF INDUSTRIAL HERITAGE ARCHITECTURE IN THE CZECH REPUBLIC

    Directory of Open Access Journals (Sweden)

    Oleg Fetisov

    2016-04-01

    Full Text Available The present paper deals with a problem of conservation and adaptive reuse of industrial heritage architecture. The relevance and topicality of the problem of adaptive reuse of industrial heritage architecture for new social and municipal functions as the conservation concept are defined. New insights on the typology of industrial architecture are reviewed (e. g. global changes in all European industry, new concepts and technologies in manufacturing, new features of industrial architecture and their construction and typology, first results of industrialization and changes in the typology of industrial architecture in post-industrial period. General goals and tasks of conservation in context of adaptive reuse of industrial heritage architecture are defined (e. g. historical, architectural and artistic, technical. Adaptive reuse as an acceptable approach for conservation and new use is proposed and reviewed. Moreover, the logical model of adaptive reuse of industrial heritage architecture as an acceptable approach for new use has been developed. Consequently, three general methods for the conservation of industrial heritage architecture by the adaptive reuse approach are developed: historical, architectural and artistic, technical. Relevant functional methods' concepts (social concepts are defined and classified. General beneficial effect of the adaptive reuse approach is given. On the basis of analysis results of experience in adaptive reuse of industrial architecture with new social functions general conclusions are developed.

  19. Wisconsin State Briefing Book for low-level radioactive waste management

    Energy Technology Data Exchange (ETDEWEB)

    1980-11-01

    The Wisconsin State Briefing Book is one of a series of state briefing books on low-level radioactive waste management practices. It has been prepared to assist state and federal agency officials in planning for safe low-level radioactive waste disposal. The report contains a profile of low-level radioactive waste generators in Wisconsin. The profile is the result of a survey of NRC licensees in Wisconsin. The briefing book also contains a comprehensive assessment of low-level radioactive waste management issues and concerns as defined by all major interested parties including industry, government, the media, and interest groups. The assessment was developed through personal communications with representatives of interested parties, and through a review of media sources. Lastly, the briefing book provides demographic and socioeconomic data and a discussion of relevant government agencies and activities, all of which may impact waste management practices in Wisconsin.

  20. Wisconsin State Briefing Book for low-level radioactive waste management

    International Nuclear Information System (INIS)

    1980-11-01

    The Wisconsin State Briefing Book is one of a series of state briefing books on low-level radioactive waste management practices. It has been prepared to assist state and federal agency officials in planning for safe low-level radioactive waste disposal. The report contains a profile of low-level radioactive waste generators in Wisconsin. The profile is the result of a survey of NRC licensees in Wisconsin. The briefing book also contains a comprehensive assessment of low-level radioactive waste management issues and concerns as defined by all major interested parties including industry, government, the media, and interest groups. The assessment was developed through personal communications with representatives of interested parties, and through a review of media sources. Lastly, the briefing book provides demographic and socioeconomic data and a discussion of relevant government agencies and activities, all of which may impact waste management practices in Wisconsin

  1. A Modular Architecture for Developing Robots for Industrial Applications

    DEFF Research Database (Denmark)

    Faina, Andres; Orjales, Felix; Souto, Daniel

    2015-01-01

    addresses the problem the other way around. In this line, we start by defining the industrial settings the architecture is aimed at and then extract the main features that would be required from a modular robotic architecture to operate successfully in this context. Finally, a particular heterogeneous......This chapter is concerned with proposing ways to make feasible the use of robots in many sectors characterized by dynamic and unstructured environments. In particular, we are interested in addressing the problem through a new approach, based on modular robotics, to allow the fast deployment...... modular robotic architecture is designed from these requirements and a laboratory implementation of it is built in order to test its capabilities and show its versatility using a set of different configurations including manipulators, climbers and walkers....

  2. Recycling architecture: industrial archeology and concrete parks

    Directory of Open Access Journals (Sweden)

    Elena Vigliocco

    2013-02-01

    Full Text Available Abandoned industrial buildings are characterized by a fragile image which makes them unworthy;however they maintain quality and potentiality that can be explored by new solutions and strategies of intervention. Inspired by issues related to reuse and recycling, a new paradigm can be formalized: unused and abandoned existing industrial buildings maintain a latent energy that can be reactivated by new strategies of reuse; like a bottle made of plastic, an architecture can be reused before throw it away through demolition. In this case, reuse is preferable than recycle. The question is: how can we reuse an architecture that is compromised by many factors like the pollution of the soil? We need a change of paradigm: if less changes will take place on buildings, than lower will be the energy required to produce them. Different renovative strategies can be classified according to the relation between intensity of the intervention and level of the modification pursued. At the same time, public administration should take an active role in the involvement of private actors: the real possibility of reducing the untenableness of urban development models will be realized on the development of new strategies and tools. Through the description of some european cases, the article will present different solutions constructed on a layering of materials and meanings.

  3. Introduction to radioactive waste management issues in Wisconsin

    International Nuclear Information System (INIS)

    Anon.

    1977-01-01

    This brief focused on wastes from commercial production of electricity and various industrial, medical and research applications of radioactive materials. Only traditionally solid wastes are dealt with. It was organized into five parts. Part I presented an introduction to radioactivity - what it is and the biological hazards associated with it. Federal regulation of the management of radioactive wastes was discussed in Part II. Existing state laws and bills currently before the Wisconsin Legislature were described in Part III. Part IV gave background information on specific areas of potential inquiry related to radioactive wastes in Wisconsin. Part V summarized the issues identified in the brief. 2 figures, 7 tables

  4. Food Processing and Agriculture. Wisconsin Annual Farm Labor Report, 1968.

    Science.gov (United States)

    Wisconsin State Employment Service, Madison.

    A yearly report on the migrant farm worker situation in Wisconsin evaluates the year 1968 in relation to past years and makes projections for the future. Comparisons are made of trends in year-round employment practices, seasonal food processing, the cherry industry, and the cucumber industry. The report includes a discussion on the social aspects…

  5. ADAPTIVE REUSE FOR NEW SOCIAL AND MUNICIPAL FUNCTIONS AS AN ACCEPTABLE APPROACH FOR CONSERVATION OF INDUSTRIAL HERITAGE ARCHITECTURE IN THE CZECH REPUBLIC

    OpenAIRE

    Oleg Fetisov

    2016-01-01

    The present paper deals with a problem of conservation and adaptive reuse of industrial heritage architecture. The relevance and topicality of the problem of adaptive reuse of industrial heritage architecture for new social and municipal functions as the conservation concept are defined. New insights on the typology of industrial architecture are reviewed (e. g. global changes in all European industry, new concepts and technologies in manufacturing, new features of industrial architecture and...

  6. Utility experiences in redevelopment of formerly used sites -- Wisconsin Electric's risk management and economic development activities

    International Nuclear Information System (INIS)

    Borofka, B.P.

    1999-01-01

    Wisconsin Electric Power Company, which recently celebrated its 100th anniversary, has actively promoted the redevelopment of its former sites as well as those of its customers. Serving Milwaukee and southeast Wisconsin, Wisconsin Electric's (WE) sites include former power plants, landfills, right-of-ways, and manufactured gas plant sites. In setting an example for others, as well as seeking to maximize the economic value of these sites, WE has either redeveloped or promoted the redevelopment of these sites by others. Examples include the East Wells Power Plant (now home of the Milwaukee Repertory Theater), the Lakeside Power Plant Site (now the home of Harnischfeger Corporation's headquarters), and the Commerce Street Power Plant located on the Milwaukee River near downtown Milwaukee. In each case the company evaluated the potential environmental liabilities against the unrealized asset value derived from facility location, site size, architectural uniqueness, or other characteristics. At the Commerce Street Power Plant, walking distance to the downtown Milwaukee business district combined with river frontage, were significant site values leveraged against a $5 million asbestos and lead-based paint removal project done to prepare the plant for marketing. More recently, WE has used its experience in promoting the redevelopment of the Menomonee River Valley, the original core of Milwaukee's industrial community, and in advancing a more practical regulatory approach to redeveloping older sites. Finally, the company is working with a non-profit community health clinic, community groups and local foundations in linking these redevelopment activities with the economic and physical health of inner city residents

  7. Geology and ground-water resources of Outagamie County, Wisconsin

    Science.gov (United States)

    LeRoux, E.F.

    1957-01-01

    Outagamie County is in east-central Wisconsin. It has no serious groundwater problem at present, but the county is important as a recharge area for the principal aquifers supplying water to Brown County and industrial Green Bay to the east.

  8. From scientific instrument to industrial machine : Coping with architectural stress in embedded systems

    NARCIS (Netherlands)

    Doornbos, R.; Loo, S. van

    2012-01-01

    Architectural stress is the inability of a system design to respond to new market demands. It is an important yet often concealed issue in high tech systems. In From scientific instrument to industrial machine, we look at the phenomenon of architectural stress in embedded systems in the context of a

  9. Matching supply networks to a modular product architecture in the house-building industry

    NARCIS (Netherlands)

    Hofman, Erwin; Voordijk, Johannes T.; Halman, Johannes I.M.

    2009-01-01

    Notions of aligning modular product architectures and buyer-supplier relationships, which have spread widely through other industrial and retail sectors, have largely bypassed the house-building industry. The major question posed in this study is: what types of contractor-supplier relationships are

  10. Small Hydropower Plants in Pomerania: The Example of Evolution of Modern Industrial Brick Architecture

    Science.gov (United States)

    Macikowski, Bartosz

    2017-10-01

    Modernism is usually recognized and associated with the aesthetics of the International Style, represented by white-plastered, horizontally articulated architecture with skimpy decoration, where function was the main imperative of the architects’ ambitions. In Northern Europe though, Modernism also revealed its brick face, representing different manners, styles, and appearances. The brick face of Modernism reflected, in fact, the complexity of the modern change, breaking ties with the historic styles of the 19th century and being still present in the beginning of the 20th century. Regardless of the cosmopolitan character of the International Style and its unified aesthetics, architects tried to find and keep shades of individuality. This was especially visible in the references to either regional or even local traditions. This diversity of modernistic architecture is intensified by its different functions. The language of industrial architecture derives its forms directly from its nature of pure functional idiom, devoted to economic and functional optimization. The industrial form usually seems subordinate to the technical nature of objects. But regardless of that, in the 19th century and the first half of the 20th century we can observe an interesting evolution of styles and tendencies in industrial architecture, even in such a narrow and specific field like the architecture of small hydropower plants. The purpose of the research was to recognize the evolution of the architectural form of hydropower plants as a developing branch of industry in the first half of the 20th century. In Pomerania, during this period, a dynamic growth of investments took place, which concerned the use of the Pomeranian rivers’ potential to produce electric energy. At the end of the 19th century, electricity had a strong meaning as a symbol of a radical civilizational change, which influenced also the aesthetic aspects of architecture. This could suggest that the architecture of

  11. Evolutionary, Unconscious Design Support for the Architectural, Engineering and Construction Industry

    NARCIS (Netherlands)

    Van de Ruitenbeek, H.K.M.

    2012-01-01

    The Architecture, Engineering and Construction (AEC) industry is a complex system in which carpenters, structural designers, architects, modellers, cost estimators, planners, politicians and many others act apart together in project-specific virtual enterprises. There is a large amount of actors, an

  12. Automation Architecture based on Cyber Physical Systems for Flexible Manufacturing within Oil&Gas Industry

    Directory of Open Access Journals (Sweden)

    Marcelo V García

    2018-03-01

    Full Text Available It is clear that in the next few years most of the technologies involved in the so-called Industry 4.0 will have a deep impact on manufacturing companies, including those related to Oil & Gas exploration and production. Low cost automation promotes reference architectures and development approaches aiming at increasing the flexibility and efficiency of production operations in industrial plants. In this sense, OPC UA, in addition to allowing companies to join the Industry 4.0 initiative, provides local and remote access to plant information, enabling a recognized mechanism for both, horizontal and vertical integration in a reliable, safe and efficient way. The contribution of this article is an open architecture for vertical integration based on cyber-physical production systems, configured under IEC 61499 and using OPC UA, suitable to achieve flexible manufacturing within Oil & Gas industry.

  13. Progress toward the Wisconsin Free Electron Laser

    International Nuclear Information System (INIS)

    Bisognano, Joseph; Bosch, R.A.; Eisert, D.; Fisher, M.V.; Green, M.A.; Jacobs, K.; Kleman, K.J.; Kulpin, J.; Rogers, G.C.; Lawler, J.E.; Yavuz, D.; Legg, R.

    2011-01-01

    The University of Wisconsin-Madison/Synchrotron Radiation Center is advancing its design for a seeded VUV/soft X-ray Free Electron Laser facility called WiFEL. To support this vision of an ultimate light source, we are pursuing a program of strategic R and D addressing several crucial elements. This includes development of a high repetition rate, VHF superconducting RF electron gun, R and D on photocathode materials by ARPES studies, and evaluation of FEL facility architectures (e.g., recirculation, compressor scenarios, CSR dechirping, undulator technologies) with the specific goal of cost containment. Studies of high harmonic generation for laser seeding are also planned.

  14. Empirical yield tables for Wisconsin.

    Science.gov (United States)

    Jerold T. Hahn; Joan M. Stelman

    1989-01-01

    Describes the tables derived from the 1983 Forest Survey of Wisconsin and presents ways the tables can be used. These tables are broken down according to Wisconsin`s five Forest Survey Units and 14 forest types.

  15. From scientific instrument to industrial machine coping with architectural stress in embedded systems

    CERN Document Server

    Doornbos, Richard

    2012-01-01

    Architectural stress is the inability of a system design to respond to new market demands. It is an important yet often concealed issue in high tech systems. In From scientific instrument to industrial machine, we look at the phenomenon of architectural stress in embedded systems in the context of a transmission electron microscope system built by FEI Company. Traditionally, transmission electron microscopes are manually operated scientific instruments, but they also have enormous potential for use in industrial applications. However, this new market has quite different characteristics. There are strong demands for cost-effective analysis, accurate and precise measurements, and ease-of-use. These demands can be translated into new system qualities, e.g. reliability, predictability and high throughput, as well as new functions, e.g. automation of electron microscopic analyses, automated focusing and positioning functions. From scientific instrument to industrial machine takes a pragmatic approach to the proble...

  16. Compact fluorescent lighting in Wisconsin: elevated atmospheric emission and landfill deposition post-EISA implementation.

    Science.gov (United States)

    Arendt, John D; Katers, John F

    2013-07-01

    The majority of states in the USA, including Wisconsin, have been affected by elevated air, soil and waterborne mercury levels. Health risks associated with mercury increase from the consumption of larger fish species, such as Walleye or Pike, which bio-accumulate mercury in muscle tissue. Federal legislation with the 2011 Mercury and Air Toxics Standards and the Wisconsin legislation on mercury, 2009 Wisconsin Act 44, continue to aim at lowering allowable levels of mercury emissions. Meanwhile, mercury-containing compact fluorescent lights (CFL) sales continue to grow as businesses and consumers move away from energy intensive incandescent light bulbs. An exchange in pollution media is occurring as airborne mercury emissions from coal-burning power plants, the largest anthropogenic source of mercury, are being reduced by lower energy demand and standards, while more universal solid waste containing mercury is generated each time a CFL is disposed. The treatment of CFLs as a 'universal waste' by the Environmental Protection Agency (EPA) led to the banning of non-household fluorescent bulbs from most municipal solid waste. Although the EPA encourages recycling of bulbs, industry currently recycles fluorescent lamps and CFLs at a rate of only 29%. Monitoring programs at the federal and state level have had only marginal success with industrial and business CFL recycling. The consumer recycling rate is even lower at only 2%. A projected increase in residential CFL use in Wisconsin owing to the ramifications of the Energy Independence and Security Act of 2007 will lead to elevated atmospheric mercury and landfill deposition in Wisconsin.

  17. Electric energy supply and non-utility generation: A comparative analysis of B.C. and Wisconsin

    International Nuclear Information System (INIS)

    Logan, J.A.

    1993-01-01

    The pricing policies and buyback rates (those concerned with purchase of non-utility generation, NUG) of British Columbia (BC) Hydro are examined along with their effectiveness in encouraging the efficient use and development of power. Specifically, the levels of self-generation within BC's pulp mills are examined as well as mill manager attitudes to increasing energy production. BC Hydro's encouragement of self-generation is determined by examining the ratio of the industrial rate for pulp mills to the utility's long-run marginal cost of power. BC Hydro's buyback policies are also examined to determine the level of encouragement they provide for increased self-generation. Comparisons are made with similar data, wherever possible, from utilities and pulp mills in Wisconsin. The comparison reveals similarities with respect to pulp mills' attitudes toward increasing self-generation capacity. A significant difference is noted in terms of the amount of pulp mill self-generation: Wisconsin mills generate substantially more of their own energy requirements than BC mills. Wisconsin utilities provided greater markup through their industrial rates, and also provided the greater encouragement for increased self-generation through their buyback policies. BC Hydro is the only utility that offered a load displacement policy, however. In summary, the policies and regulations of both BC and Wisconsin utilities have the potential to encourage greater industrial self-sufficiency and increased levels of self-generated power. Existing levels of encouragement are not determined solely by economic considerations but also reflect utility planning objectives. 97 refs., 3 figs., 20 tabs

  18. Wisconsin's forests, 2004

    Science.gov (United States)

    Charles H. (Hobie) Perry; Vern A. Everson; Ian K. Brown; Jane Cummings-Carlson; Sally E. Dahir; Edward A. Jepsen; Joe Kovach; Michael D. Labissoniere; Terry R. Mace; Eunice A. Padley; Richard B. Rideout; Brett J. Butler; Susan J. Crocker; Greg C. Liknes; Randall S. Morin; Mark D. Nelson; Barry T. (Ty) Wilson; Christopher W. Woodall

    2008-01-01

    The first full, annualized inventory of Wisconsin's forests was completed in 2004 after 6,478 forested plots were visited. There are more than 16.0 million acres of forest land in the Wisconsin, nearly half of the State's land area; 15.8 million acres meet the definition of timberland. The total area of both forest land and timberland continues an upward...

  19. Organizational Learning Supported by Reference Architecture Models: Industry 4.0 Laboratory Study

    Directory of Open Access Journals (Sweden)

    Marco Nardello

    2017-10-01

    Full Text Available The wave of the fourth industrial revolution (Industry 4.0 is bringing a new vision of the manufacturing industry. In manufacturing, one of the buzzwords of the moment is "Smart production". Smart production involves manufacturing equipment with many sensors that can generate and transmit large amounts of data. These data and information from manufacturing operations are however not shared in the organization. Therefore the organization is not using them to learn and improve their operations. To address this problem, the authors implemented in an Industry 4.0 laboratory an instance of an emerging technical standard specific for the manufacturing industry. Global manufacturing experts consider the Reference Architecture Model Industry 4.0 (RAMI4.0 as one of the corner stones for the implementation of Industry 4.0. The instantiation contributed to organizational learning in the laboratory by collecting and sharing up-to-date information concerning manufacturing equipment. This article discusses and generalizes the experience and outlines future research directions.

  20. Architectural freedom and industrialised architecture

    DEFF Research Database (Denmark)

    Vestergaard, Inge

    2012-01-01

    Architectural freedom and industrialized architecture. Inge Vestergaard, Associate Professor, Cand. Arch. Aarhus School of Architecture, Denmark Noerreport 20, 8000 Aarhus C Telephone +45 89 36 0000 E-mai l inge.vestergaard@aarch.dk Based on the repetitive architecture from the "building boom" 1960...... customization, telling exactly the revitalized storey about the change to a contemporary sustainable and better performed expression in direct relation to the given context. Through the last couple of years we have in Denmark been focusing a more sustainable and low energy building technique, which also include...... to the building physic problems a new industrialized period has started based on light weight elements basically made of wooden structures, faced with different suitable materials meant for individual expression for the specific housing area. It is the purpose of this article to widen up the different design...

  1. Using Ecotech Architecture as an Effective Tool for Sustainability in Construction Industry

    Directory of Open Access Journals (Sweden)

    A. S. Mozhdegani

    2017-10-01

    Full Text Available Ecotech architecture can be used as an effective strategy to minimize energy consumption and enhance the satisfaction of construction industry beneficiaries in the Middle East. The use of ecotech principles has been employed in different parts of the world. However, following a universal approach is not possible as local conditions are always to be considered Applications and examples of ecotech architecture are investigated in this paper. A proposed building design for the Cheetgar region in Tehran is also briefly demonstrated. A further insight on Masdar city in Abhu Dabi is provided. An overall discussion is made and key conclusions are drawn.

  2. Mixing zones studies of the waste water discharge from the Consolidated Paper Company into the Wisconsin River at Wisconsin Rapids, Wisconsin

    Science.gov (United States)

    Hoopes, J. A.; Wu, D. S.; Ganatra, R.

    1973-01-01

    Effluent concentration distributions from the waste water discharge of the Kraft Division Mill, Consolidated Paper Company, into the Wisconsin River at Wisconsin Rapids, Wisconsin, is investigated. Effluent concentrations were determined from measurements of the temperature distribution, using temperature as a tracer. Measurements of the velocity distribution in the vicinity of the outfall were also made. Due to limitations in the extent of the field observations, the analysis and comparison of the measurements is limited to the region within about 300 feet from the outfall. Effects of outfall submergence, of buoyancy and momentum of the effluent and of the pattern and magnitude of river currents on these characteristics are considered.

  3. Evolutionary, Unconscious Design Support for the Architectural, Engineering and Construction Industry

    OpenAIRE

    Van de Ruitenbeek, H.K.M.

    2012-01-01

    The Architecture, Engineering and Construction (AEC) industry is a complex system in which carpenters, structural designers, architects, modellers, cost estimators, planners, politicians and many others act apart together in project-specific virtual enterprises. There is a large amount of actors, an overwhelming number of ongoing processes, distributed, decentralised organisations and a variety of projects. This complicates efficient communication and supply chain integration which, according...

  4. Egyptian pyramid or Aztec pyramid: How should we describe the industrial architecture of automotive supply chains in Europe?

    OpenAIRE

    Vincent FRIGANT (GREThA, CNRS, UMR 5113)

    2011-01-01

    This article questions a terminology that is frequently used to describe automotive supply chains’ industrial architecture. Since vertical disintegration became a trend in the 1980s, this architecture has been represented using the image of the pyramid. Implicitly, authors have had the image of an Egyptian pyramid in mind, one that is pointed at the top and broad at the base. We will demonstrate that even if pyramids are an appropriate image, in the auto industry the Aztec variant, with its s...

  5. Forests of Wisconsin, 2013

    Science.gov (United States)

    Charles H. Perry

    2014-01-01

    This resource update provides an overview of forest resources in Wisconsin based on an inventory conducted by the U.S. Forest Service, Forest Inventory and Analysis (FIA) program at the Northern Research Station in cooperation with the Wisconsin Department of Natural Resources. Data estimates are based on field data collected using the FIA annualized sample design and...

  6. How organisation of architecture documentation affects architectural knowledge retrieval

    NARCIS (Netherlands)

    de Graaf, K.A.; Liang, P.; Tang, A.; Vliet, J.C.

    A common approach to software architecture documentation in industry projects is the use of file-based documents. This approach offers a single-dimensional arrangement of the architectural knowledge. Knowledge retrieval from file-based architecture documentation is efficient if the organisation of

  7. An architecture design and realization of the industrial CT visualization system

    International Nuclear Information System (INIS)

    Gao Long; Li Zheng; Zhang Li; Gao Wenhuan; Kang Kejun

    2003-01-01

    The Industrial Computer Tomography (ICT) is an ideal and powerful technique for inspecting and evaluating the integrity of many large and complex structures. Three dimension visualization system is the main component of ICT inspection. This paper gives an architecture design and the realization of ICT visualization system on the basis of the system analysis. A new adaptive precision algorithm is brought out to solve the main problem of interactive speed. The paper also discussed the future research intention

  8. Constraints for the design of variability-intensive service-oriented reference architectures - An industrial case study

    NARCIS (Netherlands)

    Galster, Matthias; Avgeriou, Paris; Tofan, Dan

    Context: Service-oriented architecture has become a widely used concept in software industry. However, we currently lack support for designing variability-intensive service-oriented systems. Such systems could be used in different environments, without the need to design them from scratch. To

  9. Energy-efficient architecture of industrial facilities associated with the desalination of sea water

    Directory of Open Access Journals (Sweden)

    Gazizov Timur

    2016-01-01

    Full Text Available The article offers an actual solution of a problem of drinking water shortage in the territory of the Crimean coast, in the city of Sudak, Autonomous Republic of Crimea, Russia. The project includes a development of energy-efficient architecture, its implementation in industrial facilities, such as stations for seawater desalination and an active use of alternative energy sources.

  10. Multi-Sensor As-Built Models of Complex Industrial Architectures

    Directory of Open Access Journals (Sweden)

    Jean-François Hullo

    2015-12-01

    Full Text Available In the context of increased maintenance operations and generational renewal work, a nuclear owner and operator, like Electricité de France (EDF, is invested in the scaling-up of tools and methods of “as-built virtual reality” for whole buildings and large audiences. In this paper, we first present the state of the art of scanning tools and methods used to represent a very complex architecture. Then, we propose a methodology and assess it in a large experiment carried out on the most complex building of a 1300-megawatt power plant, an 11-floor reactor building. We also present several developments that made possible the acquisition, processing and georeferencing of multiple data sources (1000+ 3D laser scans and RGB panoramic, total-station surveying, 2D floor plans and the 3D reconstruction of CAD as-built models. In addition, we introduce new concepts for user interaction with complex architecture, elaborated during the development of an application that allows a painless exploration of the whole dataset by professionals, unfamiliar with such data types. Finally, we discuss the main feedback items from this large experiment, the remaining issues for the generalization of such large-scale surveys and the future technical and scientific challenges in the field of industrial “virtual reality”.

  11. Creating Jobs through Energy Efficiency Using Wisconsin's Successful Focus on Energy Program

    Energy Technology Data Exchange (ETDEWEB)

    Akhtar, Masood; Corrigan, Edward; Reitter, Thomas

    2012-03-30

    The purpose of this project was to provide administrative and technical support for the completion of energy efficiency projects that reduce energy intensity and create or save Wisconsin industrial jobs. All projects have been completed. Details in the attached reports include project management, job development, and energy savings for each project.

  12. Wisconsin's forest resources in 2004

    Science.gov (United States)

    Charles H. Perry

    2006-01-01

    Results of the 2000-2004 annual inventory of Wisconsin show about 16.0 million acres of forest land, more than 22.1 billion cubic feet of live volume on forest land, and nearly 593 million dry tons of all live aboveground tree biomass on timberland. Populations of jack pine budworm are increasing, and it remains a significant pest in Wisconsin forests. A complete...

  13. Direct kinematics solution architectures for industrial robot manipulators: Bit-serial versus parallel

    Science.gov (United States)

    Lee, J.; Kim, K.

    1991-01-01

    A Very Large Scale Integration (VLSI) architecture for robot direct kinematic computation suitable for industrial robot manipulators was investigated. The Denavit-Hartenberg transformations are reviewed to exploit a proper processing element, namely an augmented CORDIC. Specifically, two distinct implementations are elaborated on, such as the bit-serial and parallel. Performance of each scheme is analyzed with respect to the time to compute one location of the end-effector of a 6-links manipulator, and the number of transistors required.

  14. Direct kinematics solution architectures for industrial robot manipulators: Bit-serial versus parallel

    Science.gov (United States)

    Lee, J.; Kim, K.

    A Very Large Scale Integration (VLSI) architecture for robot direct kinematic computation suitable for industrial robot manipulators was investigated. The Denavit-Hartenberg transformations are reviewed to exploit a proper processing element, namely an augmented CORDIC. Specifically, two distinct implementations are elaborated on, such as the bit-serial and parallel. Performance of each scheme is analyzed with respect to the time to compute one location of the end-effector of a 6-links manipulator, and the number of transistors required.

  15. On the Architectural Engineering Competences in Architectural Design

    DEFF Research Database (Denmark)

    Kirkegaard, Poul Henning

    2007-01-01

    In 1997 a new education in Architecture & Design at Department of Architecture and Design, Aalborg University was started with 50 students. During the recent years this number has increased to approximately 100 new students each year, i.e. approximately 500 students are following the 3 years...... bachelor (BSc) and the 2 years master (MSc) programme. The first 5 semesters are common for all students followed by 5 semesters with specialization into Architectural Design, Urban Design, Industrial Design or Digital Design. The present paper gives a short summary of the architectural engineering...

  16. Nursing Quality Assurance: The Wisconsin System

    Science.gov (United States)

    Hover, Julie; Zimmer, Marie J.

    1978-01-01

    Evaluation model guidelines for hospital departments of nursing to use in their nursing quality assurance programs are presented as developed in Wisconsin. Four essential components of the Wisconsin outcome evaluation system are criteria, assessment, standards, and improvement of care. Sample tests and charts are included in the article. (MF)

  17. An SOA-based architecture framework

    NARCIS (Netherlands)

    Aalst, van der W.M.P.; Beisiegel, M.; Hee, van K.M.; König, D.; Stahl, C.

    2007-01-01

    We present an Service-Oriented Architecture (SOA)– based architecture framework. The architecture framework is designed to be close to industry standards, especially to the Service Component Architecture (SCA). The framework is language independent and the building blocks of each system, activities

  18. Hardwood Face Veneer and Plywood Mill Closures in Michigan and Wisconsin Since 1950

    Science.gov (United States)

    Lewis T. Hendricks

    1966-01-01

    In recent years there has been a great deal of concern about the closure of numberous hardwood face veneer and plywood mills in Michigan and Wisconsin. As part of an overall study of that industry in the northern Lake States region, the basic reasons leading to the closure of these mills were investigated. In the past 15 years, there have been eight known mill...

  19. Architectural freedom and industrialised architecture

    DEFF Research Database (Denmark)

    Vestergaard, Inge

    2012-01-01

    to the building physic problems a new industrialized period has started based on light weight elements basically made of wooden structures, faced with different suitable materials meant for individual expression for the specific housing area. It is the purpose of this article to widen up the different design...... to this systematic thinking of the building technique we get a diverse and functional architecture. Creating a new and clearer story telling about new and smart system based thinking behind the architectural expression....

  20. 'Closing the Loop' in an Architectural Perspective on Strategic Organizing

    DEFF Research Database (Denmark)

    Sanchez, Ron; Galvin, Peter; Bach, Norbert

    This paper elaborates important systemic interrelationships between firms' strategic choices of product architectures and organization architectures, and between firms' architectural choices and the industry structures and competitive/cooperative dynamics that emerge in an industry. We formalize...... a "Reverse Mirroring Hypothesis" suggesting that organizational architectures desired by firms influence their choices of product architectures. We embed firms' strategic architectural decisions in a co‐evolutionary model linking product market evolution, firms' architectural choices, and industry evolution....... We invoke both transaction costs and capabilities perspectives to suggest how firms' assessments of their relative potential for capturing gains from specialization versus gains from trade influence their strategic architectural choices. We develop concepts of architectural commonality, architectural...

  1. Alternative Fuels Data Center: Wisconsin Reduces Emissions With Natural Gas

    Science.gov (United States)

    Trucks Wisconsin Reduces Emissions With Natural Gas Trucks to someone by E-mail Share Alternative Fuels Data Center: Wisconsin Reduces Emissions With Natural Gas Trucks on Facebook Tweet about Alternative Fuels Data Center: Wisconsin Reduces Emissions With Natural Gas Trucks on Twitter Bookmark

  2. Implementing high-speed rail in Wisconsin peer exchange.

    Science.gov (United States)

    2009-01-01

    The Wisconsin Department of Transportation Division of Transportation Investment Management hosted : a peer exchange on June 2 -4, 2009 in Milwaukee, Wisconsin. Representatives from four state DOTs and : two freight railroads joined representatives f...

  3. Survival of adult martens in Northern Wisconsin

    Science.gov (United States)

    Nicholas P. McCann; Patrick A. Zollner; Jonathan H. Gilbert

    2010-01-01

    Low adult marten (Martes americana) survival may be one factor limiting their population growth >30 yr after their reintroduction in Wisconsin, USA. We estimated annual adult marten survival at 0.81 in northern Wisconsin, with lower survival during winter (0.87) than summer-fall (1.00). Fisher (Martes pennanti) and raptor kills...

  4. Low-temperature waste-heat recovery in the food and paper industries

    Energy Technology Data Exchange (ETDEWEB)

    Foell, W.K.; Lund, D.; Mitchell, J.W.; Ray, D.; Stevenson, R.; TenWolde, A.

    1980-11-01

    The potential of low-temperature waste-heat recovery technology is examined. An examination of barriers to impede waste-heat recovery is made and research programs are identified. Extensive information and data are presented in the following chapters: Waste Heat Recovery in the Wisconsin Food Industry; Waste Heat Recovery in the Wisconsin Pulp and Paper Industry; Industries' Economic Analysis of Energy Conservation Projects; Industrial Waste Heat Recovery (selection of heat-recovery heat exchangers for industrial applications, simplified procedure for selection of heat recovery heat exchangers for industrial applications, selection of heat pumps for industrial applications); Institutional Aspects of Industrial Energy Conservation (economic motivation for energy conservation and the industrial response, intrafirm idea channels and their sources, evaluation and approval of plant improvement projects, reported barriers to adopting waste heat recovery projects and recommendations for government involvement, and the final chapter is a summary with major conclusions given. Additional information is given in two appendices on the potential waste heat recovery in a cheese plant (calculation) and conditions for optimum exchanger size and break-even fuel cost. (MCW)

  5. Architecture and Stages

    DEFF Research Database (Denmark)

    Kiib, Hans

    2009-01-01

    as "experiencescape" - a space between tourism, culture, learning and economy. Strategies related to these challenges involve new architectural concepts and art as ‘engines' for a change. New expressive architecture and old industrial buildings are often combined into hybrid narratives, linking the past...... with the future. But this is not enough. The agenda is to develop architectural spaces, where social interaction and learning are enhanced by art and fun. How can we develop new architectural designs in our inner cities and waterfronts where eventscapes, learning labs and temporal use are merged with everyday...

  6. Occupational safety issues in residential construction surveyed in Wisconsin, United States.

    Science.gov (United States)

    Choi, Sang D; Carlson, Kathryn

    2014-01-01

    Residential construction is a high-risk industry in the U.S. due to the exposure to work-related safety hazards and fall injuries. This study aimed to examine the safety training and safe work practices of construction workers within the small residential construction industry. In order to achieve the study objectives, a survey was designed and sent to approximately 200 Wisconsin based residential construction contractors. About one third of the respondents stated that they did not have any form of safety programs. The study indicated that the most common types of work-related injuries in residential construction were slips/trips/falls and cuts/lacerations. The survey findings also suggested that the residential construction contractors needed to increase the utilization of fall protection safety equipment. Further education and subject matter expert training could provide benefits to improve occupational safety and health of the small business workforce in the residential construction industry.

  7. Public regulations towards a tectonic architecture

    DEFF Research Database (Denmark)

    Schmidt, Anne Marie Due

    2006-01-01

    's activities has primarily been to support the optimization of the building process through ‘trimmed building’ and ‘partnering’ that only takes the immediate economic benefits of the changes to the building process into account and as such has no measures for architectural quality. The public initiatives so......Public regulations can support tectonic architecture by changes to the tendering system, supporting new organizational structures of the building industry in public building projects and suggesting a focus on innovation through increased research and development activity. The Danish state...... are happening very slowly which is understandable when there is no economic incitement for the industry to change. A change of these public regulations from sticks to carrots could create the economic incitement for the building industry to create tectonic architecture and thereby develop the building industry...

  8. Geographic and racial variation in teen pregnancy rates in Wisconsin.

    Science.gov (United States)

    Layde, Molly M; Remington, Patrick L

    2013-08-01

    Despite recent declines in teen birth rates, teenage pregnancy remains an important public health problem in Wisconsin with significant social, economic, and health-related effects. Compare and contrast teen birth rate trends by race, ethnicity, and county in Wisconsin. Teen (ages 15-19 years) birth rates (per 1000 teenage females) in Wisconsin from 2001-2010 were compared by racelethnicity and county of residence using data from the Wisconsin Interactive Statistics on Health. Teen birth rates in Wisconsin have declined by 20% over the past decade, from 35.5/1000 teens in 2001 to 28.3/1000 teens in 2010-a relative decline of 20.3%. However, trends vary by race, with declines among blacks (-33%) and whites (-26%) and increases among American Indians (+21%) and Hispanics (+30%). Minority teen birth rates continue to be 3 to 5 times greater than birth rates among whites. Rates varied even more by county, with an over 14-fold difference between Ozaukee County (7.8/1000) and Menominee County (114.2). Despite recent declines, teen pregnancy continues to be an important public health problem in Wisconsin. Pregnancy prevention programs should be targeted toward the populations and counties with the highest rates.

  9. Nurses for Wisconsin: A Collaborative Initiative to Enhance the Nurse Educator Workforce.

    Science.gov (United States)

    Young, Linda K; Adams, Jan L; Lundeen, Sally; May, Katharyn A; Smith, Rosemary; Wendt, L Elaine

    2016-01-01

    Wisconsin, like much of the nation, is currently suffering from a growing nursing shortage. The University of Wisconsin-Eau Claire College of Nursing and Health Sciences, in partnership with the University of Wisconsin-Madison, University of Wisconsin-Milwaukee, and University of Wisconsin Oshkosh nursing programs, took advantage of a University of Wisconsin System Incentive Grant for economic and workforce development to address this problem. With a $3.2 million award, the Nurses for Wisconsin goal is to increase the number of baccalaureate registered nurses by expanding the nursing education capacity within the University of Wisconsin System. Nurses for Wisconsin is accelerating the preparation of nursing faculty by supporting nurses to enroll in doctor of nursing practice or nursing doctor of philosophy programs with pre- and postdoctoral fellowship awards ranging from $21,500 to $90,000 and the recruitment of faculty with a loan repayment program of up to $50,000. In exchange for the financial support, fellows and faculty must make a 3-year commitment to teach in a UW System nursing program. Two conferences for program participants are also funded through the award. The first conference was held in October 2014. The second conference is scheduled for summer 2015. With the first year of the 2-year project completed, this article describes Nurses for Wisconsin from inception to implementation and midterm assessment with a focus on lessons learned. A follow-up article addressing final outcomes and next steps is planned. Copyright © 2016 Elsevier Inc. All rights reserved.

  10. Crowdsourcing and the Architectural Competition as Organisational Technologies

    DEFF Research Database (Denmark)

    Kamstrup, Andreas

    In this dissertation, I take interest in crowdsourcing and architectural competitions as I focus on examining how a crowdsourcing platform works in the building industry and how the practices unfolding on it relates to – and maybe mimics – architectural competitions. The platform is operated...... and situated in the building industry, where ‘the architectural competition’ stands as an institution for how to coordinate interactions between actors. I also take interest in an architectural competition setup where dialogue between architects and jury is part of the setup. In overall terms, the research...... project aims to contribute to understanding novel interaction practices in the building industry and the architectural world at large. The research is based primarily on ethnographic explorations and the results hereof is the article-based dissertation you have just embarked on. The dissertation...

  11. Environmental Education in Wisconsin: What the Textbooks Teach.

    Science.gov (United States)

    Sanera, Michael

    1996-01-01

    This report contains a study done at the request of the Wisconsin Policy Research Institute, which studies public policy issues affecting the state of Wisconsin. Environmental education texts for Grades 6 through 10 were examined for scientific and economic accuracy, objectivity, and balance in accomplishing the following: 1) stating facts that…

  12. PLM support to architecture based development

    DEFF Research Database (Denmark)

    Bruun, Hans Peter Lomholt

    , organisation, processes, etc. To identify, evaluate, and align aspects of these domains are necessary for developing the optimal layout of product architectures. It is stated in this thesis that architectures describe building principles for products, product families, and product programs, where this project...... and developing architectures can be difficult to manage, update, and maintain during development. The concept of representing product architectures in computer-based product information tools has though been central in this research, and in the creation of results. A standard PLM tool (Windchill PDMLink...... architectures in computer systems. Presented results build on research literature and experiences from industrial partners. Verification of the theory contributions, approaches, models, and tools, have been carried out in industrial projects, with promising results. This thesis describes the means for: (1...

  13. The Wisconsin Test of Adult Basic Education (WITABE).

    Science.gov (United States)

    Pandey, Tej N.; Cleary, T. Anne

    A description is given of "The Wisconsin Test of Adult Basic Education (WITABE)" which was developed specifically to measure the achievement of the individuals enrolled in the Rural Family Development (RGD) program at the University Extension, University of Wisconsin. The test is divided into three main parts or subtests: subtests 1 and…

  14. Learning from Wisconsin

    Science.gov (United States)

    Daniel, Jamie Owen

    2011-01-01

    Like thousands of other people from around the country and around the world, this author was heartened and inspired by the tenacity, immediacy, and creativity of the pushback by Wisconsin's public-sector unions against Governor Scott Walker's efforts to limit their collective bargaining rights. And like many others who made the trek to Madison to…

  15. Pupil Nondiscrimination Guidelines. Implementing S.118.13 of the Wisconsin Statutes and PI 9 of the Wisconsin Administrative Code. Bullein No. 8327.

    Science.gov (United States)

    Wisconsin State Dept. of Public Instruction, Madison.

    The new S. 118.13, Wisconsin Statutes, bans pupil discrimination in any curricular, extracurricular, pupil services, recreational, or other program or activity in the State of Wisconsin on the basis of sex; race; national origin; ancestry; creed; pregnancy; marital or parental status; sexual orientation; or physical, mental, emotional, or learning…

  16. 77 FR 59921 - Wisconsin Public Service Corporation; Notice of Environmental Site Review

    Science.gov (United States)

    2012-10-01

    ... DEPARTMENT OF ENERGY Federal Energy Regulatory Commission [Project No. 1940-000 Wisconsin; Project No. 1966-000 Wisconsin] Wisconsin Public Service Corporation; Notice of Environmental Site Review In anticipation of the filing of Notices of Intent (NOI) and Pre- Application Documents for the Grandfather Falls Hydroelectric Project No. 1966 and...

  17. University of Wisconsin - Extension

    Science.gov (United States)

    ... to know how to advance an innovative tech idea I want to know more about agricultural resources available in Wisconsin I want to learn how I can get training and support for my small business I want to learn how I can get ...

  18. Formalizing correspondence rules for automotive architectural views

    NARCIS (Netherlands)

    Dajsuren, Y.; Gerpheide, C.M.; Serebrenik, A.; Wijs, A.J.; Vasilescu, B.N.; Brand, van den M.G.J.; Seinturier, L.; Bures, T.; McGregor, J.D.

    2014-01-01

    Architecture views have long been used in software industry to systematically model complex systems by representing them from the perspective of related stakeholder concerns. However, consensus has not been reached for the architecture views between automotive architecture description languages and

  19. Undergraduate Research and Economic Development: A Systems Approach in Wisconsin

    Science.gov (United States)

    Van Galen, Dean; Schneider-Rebozo, Lissa; Havholm, Karen; Andrews, Kris

    2015-01-01

    This chapter presents the state of Wisconsin and the University of Wisconsin System as an ongoing case study for best practices in systematic, intentional, statewide programming and initiatives connecting undergraduate research and economic development.

  20. University of Wisconsin Oshkosh Anaerobic Dry Digestion Facility

    Energy Technology Data Exchange (ETDEWEB)

    Koker, John [Univ. of Wisconsin, Oshkosh, WI (United States); Lizotte, Michael [Univ. of Wisconsin, Oshkosh, WI (United States)

    2017-02-08

    The University of Wisconsin Oshkosh Anaerobic Dry Digestion Facility is a demonstration project that supported the first commercial-scale use in the United States of high solids, static pile technology for anaerobic digestion of organic waste to generate biogas for use in generating electricity and heat. The research adds to the understanding of startup, operation and supply chain issues for anaerobic digester technology. Issues and performance were documented for equipment installation and modifications, feedstock availability and quality, weekly loading and unloading of digestion chambers, chemical composition of biogas produced, and energy production. This facility also demonstrated an urban industrial ecology approach to siting such facilities near sewage treatment plants (to capture and use excess biogas generated by the plants) and organic yard waste collection sites (a source of feedstock).

  1. UW-Stout's Bachelor's in Industrial Management

    Science.gov (United States)

    Dittmann, Wendy

    2008-01-01

    The Bachelor of Science in Industrial Management (BSIM) was designed for technical college graduates with work experience because the University of Wisconsin-Stout (UW-Stout) recognized a need among adult students with technical college degrees. The program was developed to provide these students with an opportunity to earn baccalaureate degrees…

  2. Teaching Environmental Education to Wisconsin Teachers: A Review of University Course Materials.

    Science.gov (United States)

    Sanera, Michael

    1997-01-01

    This report contains a study done at the request of the Wisconsin Policy Research Institute, which studies public policy issues affecting the state of Wisconsin. The purpose of this study was to examine the content of environmental education (EE) materials used in courses required for teacher certification in Wisconsin to see if the knowledge and…

  3. Assessing the cost saving potential of shared product architectures

    DEFF Research Database (Denmark)

    Mortensen, Niels Henrik; Hansen, Christian Lindschou; Løkkegaard, Martin

    2016-01-01

    company. Experiences from the case company show it is possible to reduce the number of architectures with 60% which leads to significant reduction in direct material and labor costs. This can be achieved without compromising the market offerings of products. Experiences from the case study indicate cost......This article presents a method for calculating cost savings of shared architectures in industrial companies called Architecture Mapping and Evaluation. The main contribution is an operational method to evaluate the cost potential and evaluate the number of product architectures in an industrial...

  4. Wisconsin EE Mandates: The Bad News and the Good News.

    Science.gov (United States)

    Lane, Jennie; And Others

    1996-01-01

    Examines Wisconsin teachers' perceived competencies in, attitudes toward, and amount of class time devoted to teaching about the environment. Discusses the effects of Wisconsin environmental education mandates concerning preservice preparation in environmental education and K-12 environmental education curriculum plans. Identifies areas where the…

  5. 2001 Industry Studies: Services Industry

    National Research Council Canada - National Science Library

    Cervone, Michael

    2001-01-01

    .... has maintained its economic strength in traditional services industries such as transportation, tourism, public utilities, finance and insurance, accounting, engineering, architecture, medical, legal...

  6. Residential Energy Efficiency Potential: Wisconsin

    Energy Technology Data Exchange (ETDEWEB)

    Wilson, Eric J [National Renewable Energy Laboratory (NREL), Golden, CO (United States)

    2017-11-27

    Energy used by Wisconsin single-family homes that can be saved through cost-effective improvements. Prepared by Eric Wilson and Noel Merket, NREL, and Erin Boyd, U.S. Department of Energy Office of Energy Policy and Systems Analysis.

  7. Wisconsin Maternity Leave and Fringe Benefits: Policies, Practices and Problems.

    Science.gov (United States)

    Gerner, Jennifer

    The study examines the economic implications in Wisconsin of the 1972 Equal Employment Opportunity Commission guideline which requires employers to treat maternity leave as a temporary disability. First, the static cost of the maternity leave guideline to employers is estimated for the State of Wisconsin. Second, some examination of the economic…

  8. Teaching Case: Enterprise Architecture Specification Case Study

    Science.gov (United States)

    Steenkamp, Annette Lerine; Alawdah, Amal; Almasri, Osama; Gai, Keke; Khattab, Nidal; Swaby, Carval; Abaas, Ramy

    2013-01-01

    A graduate course in enterprise architecture had a team project component in which a real-world business case, provided by an industry sponsor, formed the basis of the project charter and the architecture statement of work. The paper aims to share the team project experience on developing the architecture specifications based on the business case…

  9. Architectural Engineers

    DEFF Research Database (Denmark)

    Petersen, Rikke Premer

    engineering is addresses from two perspectives – as an educational response and an occupational constellation. Architecture and engineering are two of the traditional design professions and they frequently meet in the occupational setting, but at educational institutions they remain largely estranged....... The paper builds on a multi-sited study of an architectural engineering program at the Technical University of Denmark and an architectural engineering team within an international engineering consultancy based on Denmark. They are both responding to new tendencies within the building industry where...... the role of engineers and architects increasingly overlap during the design process, but their approaches reflect different perceptions of the consequences. The paper discusses some of the challenges that design education, not only within engineering, is facing today: young designers must be equipped...

  10. Towards industry strength mapping of AUTOSAR automotive functionality on multicore architectures

    DEFF Research Database (Denmark)

    Avasalcai, Cosmin Florin; Budhrani, Dhanesh; Pop, Paul

    2017-01-01

    The automotive electronic architectures have moved from federated architectures, where one function is implemented in one ECU (Electronic Control Unit), to distributed architectures, consisting of several multicore ECUs. In addition, multicore ECUs are being adopted because of better performance,...... engineer in the mapping task. We have successfully evaluated AUTOMAP on several realistic use cases from Volvo Trucks....

  11. Wisconsin's forest resources, 2010

    Science.gov (United States)

    C.H. Perry

    2011-01-01

    This publication provides an overview of forest resource attributes for Wisconsin based on an annual inventory conducted by the Forest Inventory and Analysis (FIA) program at the Northern Research Station of the U.S. Forest Service. These estimates, along with web-posted core tables, will be updated annually. For more information please refer to page 4 of this report...

  12. Wisconsin's forest resources, 2005

    Science.gov (United States)

    Charles, H. (Hobie) Perry; Gary J. Brand

    2006-01-01

    The annual forest inventory of Wisconsin continues, and this document reports 2001-05 moving averages for most variables and comparisons between 2000 and 2005 for growth, removals, and mortality. Summary resource tables can be generated through the Forest Inventory Mapmaker website at http://ncrs2.fs.fed.us/4801/fiadb/index. htm. Estimates from this inventory show a...

  13. Wisconsin's forest resources, 2006

    Science.gov (United States)

    C.H. Perry; V.A. Everson

    2007-01-01

    Figure 2 was revised by the author in August 2008. This publication provides an overview of forest resource attributes for Wisconsin based on an annual inventory conducted by the Forest Inventory and Analysis program at the Northern Research Station of the U.S. Forest Service from 2002-2006. These estimates, along with associated core tables postedon the Internet, are...

  14. Wisconsin's Forest Resources, 2007

    Science.gov (United States)

    C.H. Perry; V.A. Everson

    2008-01-01

    This publication provides an overview of forest resource attributes for Wisconsin based on an annual inventory conducted by the Forest Inventory and Analysis (FIA) program of the U.S. Forest Service, Northern Research Station. These estimates, along with web-posted core tables, are updated annually. For more information please refer to page 4 of this report.

  15. Wisconsin's forest resources, 2009

    Science.gov (United States)

    C.H. Perry

    2011-01-01

    This publication provides an overview of forest resource attributes for Wisconsin based on an annual inventory conducted by the Forest Inventory and Analysis (FIA) program at the Northern Research Station of the U.S. Forest Service. These estimates, along with web-posted core tables, will be updated annually. For more information, please refer to page 4 of this report...

  16. Introduction to innovation in the East Asian automotive industry : Exploring the interplay between product architectures, firm strategies, and national innovation systems

    NARCIS (Netherlands)

    Bartnik, Roman; Wilhelm, Miriam; Fujimoto, Takahiro

    2018-01-01

    East Asia is the origin and target market for an increasing number of technological innovations. We use the East Asian automotive industry as a focal point to discuss central questions of innovation research such as modularity, product architecture, and the dynamics of state sponsorship in national

  17. Essential software architecture

    CERN Document Server

    Gorton, Ian

    2011-01-01

    Job titles like ""Technical Architect"" and ""Chief Architect"" nowadays abound in software industry, yet many people suspect that ""architecture"" is one of the most overused and least understood terms in professional software development. Gorton's book tries to resolve this dilemma. It concisely describes the essential elements of knowledge and key skills required to be a software architect. The explanations encompass the essentials of architecture thinking, practices, and supporting technologies. They range from a general understanding of structure and quality attributes through technical i

  18. The application of enterprise reference architecture in the financial industry

    NARCIS (Netherlands)

    Harmsen van der Beek - Hamer, ten W.; Trienekens, J.J.M.; Grefen, P.W.P.J.; Aier, S.

    2012-01-01

    Abstract. Financial institutions are facing enormous challenges in business / IT alignment. Enterprise architecture (EA) is seen as key in addressing these challenges. Major issues still exist in EA design and realization. The concept of reference architecture is explored as one of the elements that

  19. 40 CFR 81.30 - Southeastern Wisconsin Intrastate Air Quality Control Region.

    Science.gov (United States)

    2010-07-01

    ... Quality Control Region. 81.30 Section 81.30 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Air Quality Control Regions § 81.30 Southeastern Wisconsin Intrastate Air Quality Control Region. The Metropolitan Milwaukee Intrastate Air Quality Control Region (Wisconsin) has been renamed the Southeastern...

  20. Digitally-Driven Architecture

    Directory of Open Access Journals (Sweden)

    Henriette Bier

    2014-07-01

    Full Text Available The shift from mechanical to digital forces architects to reposition themselves: Architects generate digital information, which can be used not only in designing and fabricating building components but also in embedding behaviours into buildings. This implies that, similar to the way that industrial design and fabrication with its concepts of standardisation and serial production influenced modernist architecture, digital design and fabrication influences contemporary architecture. While standardisation focused on processes of rationalisation of form, mass-customisation as a new paradigm that replaces mass-production, addresses non-standard, complex, and flexible designs. Furthermore, knowledge about the designed object can be encoded in digital data pertaining not just to the geometry of a design but also to its physical or other behaviours within an environment. Digitally-driven architecture implies, therefore, not only digitally-designed and fabricated architecture, it also implies architecture – built form – that can be controlled, actuated, and animated by digital means.In this context, this sixth Footprint issue examines the influence of digital means as pragmatic and conceptual instruments for actuating architecture. The focus is not so much on computer-based systems for the development of architectural designs, but on architecture incorporating digital control, sens­ing, actuating, or other mechanisms that enable buildings to inter­act with their users and surroundings in real time in the real world through physical or sensory change and variation.

  1. Perspectives on digital fabrication in tomorrow's architecture

    DEFF Research Database (Denmark)

    2016-01-01

    Industrial production forms are currently undergoing a transition from being standardised to becoming customised. The change is evident for instance in architecture, arts and crafts, and industrial design. The use of robotics in the building industry allows new forms of variation and expression. ...

  2. Scalable Multi-core Architectures Design Methodologies and Tools

    CERN Document Server

    Jantsch, Axel

    2012-01-01

    As Moore’s law continues to unfold, two important trends have recently emerged. First, the growth of chip capacity is translated into a corresponding increase of number of cores. Second, the parallalization of the computation and 3D integration technologies lead to distributed memory architectures. This book provides a current snapshot of industrial and academic research, conducted as part of the European FP7 MOSART project, addressing urgent challenges in many-core architectures and application mapping.  It addresses the architectural design of many core chips, memory and data management, power management, design and programming methodologies. It also describes how new techniques have been applied in various industrial case studies. Describes trends towards distributed memory architectures and distributed power management; Integrates Network on Chip with distributed, shared memory architectures; Demonstrates novel design methodologies and frameworks for multi-core design space exploration; Shows how midll...

  3. Of Needles and Haystacks: Building an Accurate Statewide Dropout Early Warning System in Wisconsin

    Science.gov (United States)

    Knowles, Jared E.

    2015-01-01

    The state of Wisconsin has one of the highest four year graduation rates in the nation, but deep disparities among student subgroups remain. To address this the state has created the Wisconsin Dropout Early Warning System (DEWS), a predictive model of student dropout risk for students in grades six through nine. The Wisconsin DEWS is in use…

  4. Whole-system carbon balance for a regional temperate forest in Northern Wisconsin, USA

    Science.gov (United States)

    Peckham, S. D.; Gower, S. T.

    2010-12-01

    The whole-system (biological + industrial) carbon (C) balance was estimated for the Chequamegon-Nicolet National Forest (CNNF), a temperate forest covering 600,000 ha in Northern Wisconsin, USA. The biological system was modeled using a spatially-explicit version of the ecosystem process model Biome-BGC. The industrial system was modeled using life cycle inventory (LCI) models for wood and paper products. Biome-BGC was used to estimate net primary production, net ecosystem production (NEP), and timber harvest (H) over the entire CNNF. The industrial carbon budget (Ci) was estimated by applying LCI models of CO2 emissions resulting from timber harvest and production of specific wood and paper products in the CNNF region. In 2009, simulated NEP of the CNNF averaged 3.0 tC/ha and H averaged 0.1 tC/ha. Despite model uncertainty, the CNNF region is likely a carbon sink (NEP - Ci > 0), even when CO2 emissions from timber harvest and production of wood and paper products are included in the calculation of the entire forest system C budget.

  5. Rollout Strategy to Implement Interoperable Traceability in the Seafood Industry.

    Science.gov (United States)

    Gooch, Martin; Dent, Benjamin; Sylvia, Gilbert; Cusack, Christopher

    2017-08-01

    Verifying the accuracy and rigor of data exchanged within and between businesses for the purposes of traceability rests on the existence of effective and efficient interoperable information systems that meet users' needs. Interoperability, particularly given the complexities intrinsic to the seafood industry, requires that the systems used by businesses operating along the supply chain share a common technology architecture that is robust, resilient, and evolves as industry needs change. Technology architectures are developed through engaging industry stakeholders in understanding why an architecture is required, the benefits provided to the industry and individual businesses and supply chains, and how the architecture will translate into practical results. This article begins by reiterating the benefits that the global seafood industry can capture by implementing interoperable chain-length traceability and the reason for basing the architecture on a peer-to-peer networked database concept versus more traditional centralized or linear approaches. A summary of capabilities that already exist within the seafood industry that the proposed architecture uses is discussed; and a strategy for implementing the architecture is presented. The 6-step strategy is presented in the form of a critical path. © 2017 Institute of Food Technologists®.

  6. Organizational Learning Supported by Reference Architecture Models

    DEFF Research Database (Denmark)

    Nardello, Marco; Møller, Charles; Gøtze, John

    2017-01-01

    of an emerging technical standard specific for the manufacturing industry. Global manufacturing experts consider the Reference Architecture Model Industry 4.0 (RAMI4.0) as one of the corner stones for the implementation of Industry 4.0. The instantiation contributed to organizational learning in the laboratory...

  7. Assessment of high penetration of solar photovoltaics in Wisconsin

    International Nuclear Information System (INIS)

    Myers, Kevin S.; Klein, Sanford A.; Reindl, Douglas T.

    2010-01-01

    This paper provides an assessment of the large-scale implementation of distributed solar photovoltaics in Wisconsin with regard to its interaction with the utility grid, economics of varying levels of high penetration, and displaced emissions. These assessment factors are quantified using simulations with measured hourly solar radiation and weather data from the National Solar Radiation Database as primary inputs. Hourly utility load data for each electric utility in Wisconsin for a complete year were used in combination with the simulated PV output to quantify the impacts of high penetration of distributed PV on the aggregate Wisconsin electric utility load. As the penetration rate of distributed PV systems increases, both economic and environmental benefits experience diminishing returns. At penetration rates exceeding 15-20% of the aggregate utility load peak, less of the PV-energy is utilized and the contribution of the aggregate electricity generated from PV approaches a practical limit. The limit is not affected by costs, but rather by the time-distribution of available solar radiation and mismatch with the coincidence of aggregate utility electrical loads. The unsubsidized levelized cost of electricity from PV is more than four times greater than the current market price for electricity, based on time-of-use rates, in Wisconsin. At the present time, the investment in solar PV as a cost-effective means to reduce emissions from traditional electricity generation sources is not justified. (author)

  8. The Wisconsin experience with incentives for demand-side management

    International Nuclear Information System (INIS)

    Landgren, D.A.

    1990-01-01

    It has been noted that, within traditional regulatory frameworks for electric utilities, factors exist which discourage demand side management (DSM) and that there is a lack of positive incentives for DSM. Regulatory agencies should therefore make it possible for DSM measures to benefit from the same treatment as supply-side measures. The Wisconsin Public Service Commission (WPSC) has recognized this need and has adopted various measures accordingly. The need for efficiency incentives is described according to the particular experience of Wisconsin Electric concerning their recourse to a DSM incentive and according to new incentive models being tested in collaboration with other electricity suppliers in Wisconsin. The WPSC has concluded that the fact of considering the costs relating to DSM as expenses or capitalizing them within the rate base does not motivate the utility to promote DSM programs. The WPSC has thus decided to experiment with energy efficiency incentives in order to evaluate their eventual impact. The choice of the type of incentive had an objective of starting the process in an area where the lack of experience has created, from the regulatory point of view, a reticence on the part of utilities to engage in DSM programs. The WPSC has designed a variety of incentive models which have been adapted to each utility's own situation. Specific incentive programs developed for three Wisconsin utilities are reviewed

  9. Wisconsin Earth and Space Science Education

    Science.gov (United States)

    Bilbrough, Larry (Technical Monitor); French, George

    2003-01-01

    The Wisconsin Earth and Space Science Education project successfilly met its objectives of creating a comprehensive online portfolio of science education curricular resources and providing a professional development program to increase educator competency with Earth and Space science content and teaching pedagogy. Overall, 97% of participants stated that their experience was either good or excellent. The favorable response of participant reactions to the professional development opportunities highlights the high quality of the professional development opportunity. The enthusiasm generated for using the curricular material in classroom settings was overwhelmingly positive at 92%. This enthusiasm carried over into actual classroom implementation of resources from the curricular portfolio, with 90% using the resources between 1-6 times during the school year. The project has had a positive impact on student learning in Wisconsin. Although direct measurement of student performance is not possible in a project of this kind, nearly 75% of participating teachers stated that they saw an increase in student performance in math and science as a result of using project resources. Additionally, nearly 75% of participants saw an increase in the enthusiasm of students towards math and science. Finally, some evidence exists that the professional development academies and curricular portfolio have been effective in changing educator behavior. More than half of all participants indicated that they have used more hands-on activities as a result of the Wisconsin Earth and Space Science Education project.

  10. Predicting Scour of Bedrock in Wisconsin

    Science.gov (United States)

    2017-04-01

    This research evaluates the scour potential of rocks supporting Wisconsin DOT bridge foundations. Ten highway bridges were selected for this study, of which seven are supported by shallow foundations, and five were built on sandstone in rivers/stream...

  11. Understanding Enterprise Architecture with Topic Modeling

    DEFF Research Database (Denmark)

    Nardello, Marco; Møller, Charles; Gøtze, John

    2018-01-01

    The next 3 years will be more important than the last 50 due to the digital transformation across industries. Enterprise Architecture (EA), the discipline that should lead enterprise responses to disruptive forces, is far from ready to drive the next wave of change. The state of the art in the di......The next 3 years will be more important than the last 50 due to the digital transformation across industries. Enterprise Architecture (EA), the discipline that should lead enterprise responses to disruptive forces, is far from ready to drive the next wave of change. The state of the art...

  12. ATCA for Machines-- Advanced Telecommunications Computing Architecture

    Energy Technology Data Exchange (ETDEWEB)

    Larsen, R.S.; /SLAC

    2008-04-22

    The Advanced Telecommunications Computing Architecture is a new industry open standard for electronics instrument modules and shelves being evaluated for the International Linear Collider (ILC). It is the first industrial standard designed for High Availability (HA). ILC availability simulations have shown clearly that the capabilities of ATCA are needed in order to achieve acceptable integrated luminosity. The ATCA architecture looks attractive for beam instruments and detector applications as well. This paper provides an overview of ongoing R&D including application of HA principles to power electronics systems.

  13. Digitally-Driven Architecture

    Directory of Open Access Journals (Sweden)

    Henriette Bier

    2010-06-01

    Full Text Available The shift from mechanical to digital forces architects to reposition themselves: Architects generate digital information, which can be used not only in designing and fabricating building components but also in embedding behaviours into buildings. This implies that, similar to the way that industrial design and fabrication with its concepts of standardisation and serial production influenced modernist architecture, digital design and fabrication influences contemporary architecture. While standardisa­tion focused on processes of rationalisation of form, mass-customisation as a new paradigm that replaces mass-production, addresses non-standard, complex, and flexible designs. Furthermore, knowledge about the designed object can be encoded in digital data pertaining not just to the geometry of a design but also to its physical or other behaviours within an environment. Digitally-driven architecture implies, therefore, not only digitally-designed and fabricated architecture, it also implies architecture – built form – that can be controlled, actuated, and animated by digital means. In this context, this sixth Footprint issue examines the influence of digital means as prag­matic and conceptual instruments for actuating architecture. The focus is not so much on computer-based systems for the development of architectural designs, but on architecture incorporating digital control, sens­ing, actuating, or other mechanisms that enable buildings to inter­act with their users and surroundings in real time in the real world through physical or sensory change and variation.

  14. An Empirical Investigation of Architectural Prototyping

    DEFF Research Database (Denmark)

    Christensen, Henrik Bærbak; Hansen, Klaus Marius

    2010-01-01

    Architectural prototyping is the process of using executable code to investigate stakeholders’ software architecture concerns with respect to a system under development. Previous work has established this as a useful and cost-effective way of exploration and learning of the design space of a system...... and in addressing issues regarding quality attributes, architectural risks, and the problem of knowledge transfer and conformance. However, the actual industrial use of architectural prototyping has not been thoroughly researched so far. In this article, we report from three studies of architectural prototyping...... in practice. First, we report findings from an ethnographic study of practicing software architects. Secondly, we report from a focus group on architectural prototyping involving architects from four companies. And, thirdly, we report from a survey study of 20 practicing software architects and software...

  15. Creating a perfect storm to increase consumer demand for Wisconsin's Tobacco Quitline.

    Science.gov (United States)

    Sheffer, Megan A; Redmond, Lezli A; Kobinsky, Kate H; Keller, Paula A; McAfee, Tim; Fiore, Michael C

    2010-03-01

    Telephone quitlines are a clinically proven and cost-effective population-wide tobacco-dependence treatment, and this option is now available in all 50 states. Yet, only 1% of the smoking population accesses these services annually. This report describes a series of policy, programmatic, and communication initiatives recently implemented in Wisconsin that resulted in a dramatic increase in consumer demand for the Wisconsin Tobacco Quitline (WTQL). In 2007, the Wisconsin legislature voted to increase the state cigarette excise tax rate by $1.00, from $0.77/pack to $1.77/pack effective January 1, 2008. In preparation for the tax increase, the Wisconsin Tobacco Prevention and Control Program, the University of Wisconsin Center for Tobacco Research and Intervention, which manages the WTQL, and the state's quitline service provider, Free & Clear, Inc., collaborated to enhance quitline knowledge, availability, and services with the goal of increasing consumer demand for services. The enhancements included for the first time, a free 2-week supply of over-the-counter nicotine replacement medication for tobacco users who agreed to receive multi-session quitline counseling. A successful statewide earned media campaign intensified the impact of these activities, which were timed to coincide with temporal smoking-cessation behavioral patterns (i.e., New Year's resolutions). As a result, the WTQL fielded a record 27,000 calls during the first 3 months of 2008, reaching nearly 3% of adult Wisconsin smokers. This experience demonstrates that consumer demand for quitline services can be markedly enhanced through policy and communication initiatives to increase the population reach of this evidence-based treatment. Published by Elsevier Inc.

  16. Variations in Withdrawal, Return Flow, and Consumptive Use of Water in Ohio and Indiana, with Selected Data from Wisconsin, 1999-2004

    Science.gov (United States)

    Shaffer, Kimberly H.

    2009-01-01

    This report contains an analysis of water withdrawal and return-flow data for Ohio and withdrawal data for Indiana and Wisconsin to compute consumptive-use coefficients and to describe monthly variability of withdrawals and consumptive use. Concurrent data were available for most water-use categories from 1999 through 2004. Average monthly water withdrawals are discussed for a variety of water-use categories, and average water use per month is depicted graphically for Ohio, Indiana, and Wisconsin (public supply only). For most water-use categories, the summer months were those of highest withdrawal and highest consumptive use. For public supply, average monthly withdrawals ranged from 1,380 million gallons per day (Mgal/d) (November) to 1,620 Mgal/d (July) in Ohio, 621 Mgal/d (December) to 816 Mgal/d (July) in Indiana, and 515 Mgal/d (December) to 694 Mgal/d (July) in Wisconsin. Ohio and Indiana thermoelectric facilities had large increases in average monthly withdrawals in the summer months (5,520 Mgal/d in March to 7,510 Mgal/d in August for Indiana; 7,380 Mgal/d in February to 10,040 Mgal/d in July for Ohio), possibly because of increased electricity production in the summer, a need for additional cooling-water withdrawals when intake-water temperature is high, or use of different types of cooling methods during different times of the year. Average industrial withdrawals ranged from 2,220 Mgal/d (December) to 2,620 Mgal/d (August) in Indiana and from 707 Mgal/d (January) to 787 Mgal/d (August) in Ohio. The Ohio and Indiana irrigation data showed that most withdrawals were in May through October for golf courses, nurseries, and crop irrigation. Commercial water withdrawals ranged from 30.4 Mgal/d (January) to 65.0 Mgal/d (September) in Indiana and from 23.2 Mgal/d (November) to 49.5 Mgal/d (August) in Ohio; commercial facilities that have high water demand in Ohio and Indiana are medical facilities, schools, amusement facilities, wildlife facilities, large stores

  17. ATCA for Machines-- Advanced Telecommunications Computing Architecture

    International Nuclear Information System (INIS)

    Larsen, R

    2008-01-01

    The Advanced Telecommunications Computing Architecture is a new industry open standard for electronics instrument modules and shelves being evaluated for the International Linear Collider (ILC). It is the first industrial standard designed for High Availability (HA). ILC availability simulations have shown clearly that the capabilities of ATCA are needed in order to achieve acceptable integrated luminosity. The ATCA architecture looks attractive for beam instruments and detector applications as well. This paper provides an overview of ongoing R and D including application of HA principles to power electronics systems

  18. Cost-Effectiveness Analysis of the Residential Provisions of the 2015 IECC for Wisconsin

    Energy Technology Data Exchange (ETDEWEB)

    Mendon, Vrushali V. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Zhao, Mingjie [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Taylor, Zachary T. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Poehlman, Eric A. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

    2016-02-15

    The 2015 IECC provides cost-effective savings for residential buildings in Wisconsin. Moving to the 2015 IECC from the 2006 IECC base code is cost-effective for residential buildings in all climate zones in Wisconsin.

  19. Wisconsin's fourth forest inventory, 1983.

    Science.gov (United States)

    John S. Jr. Spencer; W. Brad Smith; Jerold T. Hahn; Gerhard K. Raile

    1988-01-01

    The fourth inventory of the timber resource of Wisconsin shows that growing-stock volume increased from 11.2 to 15.5 billion cubic feet between 1968 and 1983, and area of timberland increased from 14.5 to 14.8 million acres. Presented are analysis and statistics on forest area and timber volume, growth, mortality, removals, and projections.

  20. Flood-frequency characteristics of Wisconsin streams

    Science.gov (United States)

    Walker, John F.; Peppler, Marie C.; Danz, Mari E.; Hubbard, Laura E.

    2017-05-22

    Flood-frequency characteristics for 360 gaged sites on unregulated rural streams in Wisconsin are presented for percent annual exceedance probabilities ranging from 0.2 to 50 using a statewide skewness map developed for this report. Equations of the relations between flood-frequency and drainage-basin characteristics were developed by multiple-regression analyses. Flood-frequency characteristics for ungaged sites on unregulated, rural streams can be estimated by use of the equations presented in this report. The State was divided into eight areas of similar physiographic characteristics. The most significant basin characteristics are drainage area, soil saturated hydraulic conductivity, main-channel slope, and several land-use variables. The standard error of prediction for the equation for the 1-percent annual exceedance probability flood ranges from 56 to 70 percent for Wisconsin Streams; these values are larger than results presented in previous reports. The increase in the standard error of prediction is likely due to increased variability of the annual-peak discharges, resulting in increased variability in the magnitude of flood peaks at higher frequencies. For each of the unregulated rural streamflow-gaging stations, a weighted estimate based on the at-site log Pearson type III analysis and the multiple regression results was determined. The weighted estimate generally has a lower uncertainty than either the Log Pearson type III or multiple regression estimates. For regulated streams, a graphical method for estimating flood-frequency characteristics was developed from the relations of discharge and drainage area for selected annual exceedance probabilities. Graphs for the major regulated streams in Wisconsin are presented in the report.

  1. 76 FR 57646 - Final Withdrawal of Certain Federal Aquatic Life Water Quality Criteria Applicable to Wisconsin

    Science.gov (United States)

    2011-09-16

    ... Final Withdrawal of Certain Federal Aquatic Life Water Quality Criteria Applicable to Wisconsin AGENCY... aquatic life water quality criteria applicable to Wisconsin? C. Why is the EPA not withdrawing Wisconsin's chronic endrin aquatic life use criterion for waters designated as Warm Water Sportfish and Warm Water...

  2. Wisconsin Educators Tackle Violence Head On.

    Science.gov (United States)

    Jones, Katherine A.

    1999-01-01

    In August 1999, Wisconsin school business officials and other school administrators met with police officers to discuss cooperative ventures to ensure school safety. Conference participants attended sessions on identifying troubled students, physical security measures, safety planning, dealing with bomb threats, and prevention and punishment. (MLH)

  3. Libraries in Wisconsin Institutions: Status Report.

    Science.gov (United States)

    Merriam, Elizabeth B.

    The Wisconsin Library Association Round Table of Hospitals and Institutional Librarians became concerned about adequate funding of institutional libraries; the right of institutionalized persons to read and to have educational, legal, and recreational materials; and the development of staff libraries for treatment, rehabilitation, and research…

  4. Architectures for single-chip image computing

    Science.gov (United States)

    Gove, Robert J.

    1992-04-01

    This paper will focus on the architectures of VLSI programmable processing components for image computing applications. TI, the maker of industry-leading RISC, DSP, and graphics components, has developed an architecture for a new-generation of image processors capable of implementing a plurality of image, graphics, video, and audio computing functions. We will show that the use of a single-chip heterogeneous MIMD parallel architecture best suits this class of processors--those which will dominate the desktop multimedia, document imaging, computer graphics, and visualization systems of this decade.

  5. Architecture and construction’s industrialization in the work of João Filgueiras Lima – Lelé

    Directory of Open Access Journals (Sweden)

    Elza Luli Miyasaka

    2016-04-01

    Full Text Available Arquitectura e industrialización de la construcción en la obra de João Filgueiras Lima – LeléResumenLa industrialización de un edificio requiere un alto rigor técnico en su diseño y producción. En Brasil, la obra del arquitecto João Filgueiras Lima, “Lelé”, se destaca como un ejemplo del proceso de diseño de los edificios industriales, que abarcan todas las etapas de la construcción. Este artículo ofrece la trayectoria tecnológica de Lele y el desarrollo de la producción industrial a través de sus diversas experiencias en las fábricas para el desempeño de los sistemas de construcción. A continuación, se analiza su producción industrializada en el Marco de Apoyo Comunitario de Ribeirão Preto (São Paulo, Brasil, aún poco conocida. Como método se utilizó un estudio de caso único, con múltiples fuentes de evidencia, tales como entrevistas, observación directa y documentos. De los resultados, parece que “Lelé” ha mejorado constantemente sus prácticas de construcción y elementos industrializados utilizados ya que participó en todo el proceso de construcción de edificios. Aunque se hace uso de la producción en masa, obtiene un apropiado método para el contexto en el que se insertan los edificios complejos. Palabras clave: arquitectura brasileña, arquitectura industrial, diseño constructivo, edificio industrial, industria de la construcción, procesos y técnicas de construcción. Architecture and construction’s industrialization in the work of João Filgueiras Lima – LeléAbstractThe industrialization of a building requires high technical rigor in design and production. In Brazil, the architect João Filgueiras Lima, “Lele” stands out as an example of the design process of industrial buildings, covering all stages of construction. This article provides the technological trajectory of Lele and development of industrial production through their diverse experiences in factories for the performance

  6. Lyme disease in Wisconsin: epidemiologic, clinical, serologic, and entomologic findings.

    Science.gov (United States)

    Davis, J P; Schell, W L; Amundson, T E; Godsey, M S; Spielman, A; Burgdorfer, W; Barbour, A G; LaVenture, M; Kaslow, R A

    1984-01-01

    In 1980-82, 80 individuals (71 Wisconsin residents) had confirmed Lyme disease (LD-c) reported; 39 additional patients had probable or possible LD. All cases of LD-c occurred during May-November; 73 percent occurred during June-July; 54 (68 percent) occurred in males. The mean age was 38.7 years (range, 7-77 years). Among LD-c patients, likely exposure to the presumed vector Ixodes dammini (ID) occurred in 22 different Wisconsin counties. Antibodies to the ID spirochete that causes LD occurred in 33 of 49 LD-c cases versus 0 of 18 in ill controls (p less than .001) and in 13 of 26 LD-c cases treated with penicillin or tetracycline versus 16 of 19 LD-c cases not treated. Early antibiotic therapy appears to blunt the antibody response to the ID spirochete. Regional tick surveys conducted in Wisconsin during each November in 1979-82 have demonstrated regions of greater density of ID. Utilizing comparable tick collection in these surveys, increases were noted in the percentage of deer with ID from 24 percent (31/128) in 1979 to 38 percent (58/152) in 1981, in the standardized mean value of ID/deer from 1.0 in 1979 to 2.2 in 1981, in the percentage of ID of the total ticks collected from 13 percent in 1979 to 71 percent in 1981, or in the ratio of ID to Dermacentor albipictus ticks from 0.14 in 1979 to 2.44 in 1981. However, a reduction in the density of ID/deer was noted generally throughout Wisconsin in 1982 when compared to 1981. LD is widespread in Wisconsin, with ecologic and clinical features similar to those occurring along the eastern seaboard.

  7. The evolution of Wisconsin's urban FIA program—yesterday today and tomorrow

    Science.gov (United States)

    Andrew M. Stoltman; Richard B. Rideout

    2015-01-01

    In 2002, Wisconsin was part of two pilot projects in cooperation with the US Forest Service. The first was a street tree assessment, and the second was an urban FIA project. The data generated by these pilots changed the way that Wisconsin DNRs’ Urban Forestry Program conducts its business. Although there have been several urban FIA pilot projects throughout the U.S.,...

  8. Architecture of Environmental Engineering

    DEFF Research Database (Denmark)

    Wenzel, Henrik; Alting, Leo

    2006-01-01

    An architecture of Environmental Engineering has been developed comprising the various disciplines and tools involved. It identifies industry as the major actor and target group, and it builds on the concept of Eco-efficiency. To improve Eco-efficiency, there is a limited number of intervention......-efficiency is the aim of Environmental Engineering, the discipline of synthesis – design and creation of solutions – will form a core pillar of the architecture. Other disciplines of Environmental Engineering exist forming the necessary background and frame for the synthesis. Environmental Engineering, thus, in essence...... comprise the disciplines of: management, system description & inventory, analysis & assessment, prioritisation, synthesis, and communication, each existing at all levels of intervention. The developed architecture of Environmental Engineering, thus, consists of thirty individual disciplines, within each...

  9. Architecture of Environmental Engineering

    DEFF Research Database (Denmark)

    Wenzel, Henrik; Alting, Leo

    2004-01-01

    An architecture of Environmental Engineering has been developed comprising the various disciplines and tools involved. It identifies industry as the major actor and target group, and it builds on the concept of Eco-efficiency. To improve Eco-efficiency, there is a limited number of intervention...... of Eco-efficiency is the aim of Environmental Engineering, the discipline of synthesis – design and creation of solutions – will form a core pillar of the architecture. Other disciplines of Environmental Engineering exist forming the necessary background and frame for the synthesis. Environmental...... Engineering, thus, in essence comprise the disciplines of: management, system description & inventory, analysis & assessment, prioritisation, synthesis, and communication, each existing at all levels of intervention. The developed architecture of Environmental Engineering, thus, consists of thirty individual...

  10. Geodemographic Features of Human Blastomycosis in Eastern Wisconsin

    Directory of Open Access Journals (Sweden)

    Megan E. Huber

    2016-04-01

    Full Text Available Purpose: Blastomycosis is an endemic fungal infection. In rural northern Wisconsin, blastomycosis cases are associated with certain environmental features including close proximity to waterways. Other studies have associated blastomycosis with particular soil chemicals. However, blastomycosis also occurs in urban and suburban regions. We explored the geodemographic associations of blastomycosis cases in the more urban/suburban landscape of eastern Wisconsin. Methods: We conducted a retrospective study of 193 laboratory-identified blastomycosis cases in a single eastern Wisconsin health system, 2007–2015. Controls were 250 randomly selected cases of community-diagnosed pneumonia from a similar time period. Geographic features of home addresses were explored using Google Maps. Categorical variables were analyzed with chi-square or Fisher’s exact tests and continuous variables by two-sample t-tests. Stepwise regression followed by binary logistic regression was used for multivariable analysis. Results: Compared to pneumonia cases, blastomycosis cases were younger (47.7 vs. 55.3 years and more likely to be male (67.9% vs. 45.6%, nonwhite (23.2% vs. 9.7% and machinists, automobile workers/mechanics or construction workers (32.7% vs. 7.2%; P 0.5 acres (30.4% vs. 14.2%, P = 0.0002, be < 0.25 miles from an automobile repair facility or junkyard (35.9% vs. 19.4%, P = 0.0005, and be < 0.1 miles from a park, forest or farm field (54.9% vs. 39.6%, P = 0.002. Only the latter association remained on multivariable analysis. Conclusions: Eastern Wisconsin blastomycosis case subjects were younger, more often male and more likely to live near parks/forests/fields. Novel associations of blastomycosis cases with machinery- and automobile-related occupations and/or facilities should be further explored.

  11. Divided Wisconsin: Partisan Spatial Electoral Realignment

    Science.gov (United States)

    Zaniewski, Kazimierz J.; Simmons, James R.

    2016-01-01

    When the Republican and Democratic presidential candidates head into the general election this fall, they will be courting votes from a statewide electorate that has dramatically shifted over time, mirroring the political polarization that is happening across the country. Over the last three decades, Wisconsin's political geography has evolved…

  12. Architecture for autonomy

    Science.gov (United States)

    Broten, Gregory S.; Monckton, Simon P.; Collier, Jack; Giesbrecht, Jared

    2006-05-01

    In 2002 Defence R&D Canada changed research direction from pure tele-operated land vehicles to general autonomy for land, air, and sea craft. The unique constraints of the military environment coupled with the complexity of autonomous systems drove DRDC to carefully plan a research and development infrastructure that would provide state of the art tools without restricting research scope. DRDC's long term objectives for its autonomy program address disparate unmanned ground vehicle (UGV), unattended ground sensor (UGS), air (UAV), and subsea and surface (UUV and USV) vehicles operating together with minimal human oversight. Individually, these systems will range in complexity from simple reconnaissance mini-UAVs streaming video to sophisticated autonomous combat UGVs exploiting embedded and remote sensing. Together, these systems can provide low risk, long endurance, battlefield services assuming they can communicate and cooperate with manned and unmanned systems. A key enabling technology for this new research is a software architecture capable of meeting both DRDC's current and future requirements. DRDC built upon recent advances in the computing science field while developing its software architecture know as the Architecture for Autonomy (AFA). Although a well established practice in computing science, frameworks have only recently entered common use by unmanned vehicles. For industry and government, the complexity, cost, and time to re-implement stable systems often exceeds the perceived benefits of adopting a modern software infrastructure. Thus, most persevere with legacy software, adapting and modifying software when and wherever possible or necessary -- adopting strategic software frameworks only when no justifiable legacy exists. Conversely, academic programs with short one or two year projects frequently exploit strategic software frameworks but with little enduring impact. The open-source movement radically changes this picture. Academic frameworks

  13. Robotic fabrication in architecture, art, and design

    CERN Document Server

    Braumann, Johannes

    2013-01-01

    Architects, artists, and designers have been fascinated by robots for many decades, from Villemard’s utopian vision of an architect building a house with robotic labor in 1910, to the design of buildings that are robots themselves, such as Archigram’s Walking City. Today, they are again approaching the topic of robotic fabrication but this time employing a different strategy: instead of utopian proposals like Archigram’s or the highly specialized robots that were used by Japan’s construction industry in the 1990s, the current focus of architectural robotics is on industrial robots. These robotic arms have six degrees of freedom and are widely used in industry, especially for automotive production lines. What makes robotic arms so interesting for the creative industry is their multi-functionality: instead of having to develop specialized machines, a multifunctional robot arm can be equipped with a wide range of end-effectors, similar to a human hand using various tools. Therefore, architectural researc...

  14. SOLPLAN Report: An Assessment of Barriers and Incentives to Conservation and Alternative-Energy Use in the Residential Sector in Wisconsin

    Energy Technology Data Exchange (ETDEWEB)

    Fulenwider, Claire K.; Weiss, Lonnie S.; Pfefferkorn, Carol; Wiener, Don E.; Feldman, Stephen L.

    1981-03-01

    The Alternative Energy Policy Project of the Wisconsin Center for Public Policy focused upon two principle objectives: (1) gathering and analyzing new and previously unavailable data on barriers and incentives to greater energy conservation and alternative energy commercialization in the state of Wisconsin; and (2) building consensus around alternative energy policy to develop guidelines for alternative energy policy for the state. Particular attention was paid to public involvement in the policy process and to assessing barriers and incentives from as many key sectors of the energy field as possible. Thus, data were gathered from the general public, alternative energy users, the heating industry generally, the alternative-energy industry specifically, and key decision makers. The report is divided into four principal sections. The first looks at findings and analyses dealing with barriers to greater conservation and alternative energy use. Incentives for accelerating the extent of residential conservation and alternative energy use are discussed in the second section. The decision-making process itself in energy policy has been little analyzed and seldom documented. The role of consensus-building in the alternative-energy field and analysis of the decision-making process are discussed in Section III. Appendices in Section IV provide survey instruments and descriptions, a compendium of energy-related legislation developed within the project, and various reports. The total report reflects the interactive decision-making model as it was applied in SOLPLAN. (MCW)

  15. 78 FR 48900 - Notice of Inventory Completion: State Historical Society of Wisconsin, Madison, WI

    Science.gov (United States)

    2013-08-12

    .... ADDRESSES: Jennifer Kolb, Wisconsin Historical Museum, 30 North Carroll Street, Madison, WI 53703, telephone (608) 261-2461, email Jennifer.Kolb@wisconsinhistory.org . SUPPLEMENTARY INFORMATION: Notice is here... request to Jennifer Kolb, Wisconsin Historical Museum, 30 North Carroll Street, Madison, WI 53703...

  16. Informed Forces for Environmental Quality, Conference Proceedings (University of Wisconsin, Green Bay, Wisconsin, March 28-29, 1968).

    Science.gov (United States)

    Wisconsin Univ., Green Bay.

    To increase understanding of the dimensions of man's impact on his environment and the key issues involved in improving that environment through education and action was the goal of the environmental quality conference held at the University of Wisconsin, Green Bay, on March 28-29, 1968. Contained in this document are the conference…

  17. Wisconsin's forest statistics, 1987: an inventory update.

    Science.gov (United States)

    W. Brad Smith; Jerold T. Hahn

    1989-01-01

    The Wisconsin 1987 inventory update, derived by using tree growth models, reports 14.7 million acres of timberland, a decline of less than 1% since 1983. This bulletin presents findings from the inventory update in tables detailing timberland area, volume, and biomass.

  18. Wisconsin Public Schools at a Glance

    Science.gov (United States)

    Wisconsin Department of Public Instruction, 2014

    2014-01-01

    "Wisconsin Public Schools at a Glance" provides in a single page document statistical information on the following topics: (1) Total number of public schools (2014-15); (2) Staff (2013-14); (3) Students (2013-14);(4) Report Cards (2013-14); (5) Attendance and Graduation (2012-13); (6) Student Performance (2013-14); and (7) School Funding.

  19. Design of complex architectures using a three dimension approach : the crosswork case

    NARCIS (Netherlands)

    Seguel Pérez, R.E.; Grefen, P.W.P.J.; Eshuis, H.

    2010-01-01

    In this paper, we present a three dimensional design approach of complex information systems architectures. Key element of this approach is the model transformation cube, which consists of three dimensions along which architecture models can be positioned. Industry architecture frameworks to guide

  20. Private drinking water quality in rural Wisconsin.

    Science.gov (United States)

    Knobeloch, Lynda; Gorski, Patrick; Christenson, Megan; Anderson, Henry

    2013-03-01

    Between July 1, 2007, and December 31, 2010, Wisconsin health departments tested nearly 4,000 rural drinking water supplies for coliform bacteria, nitrate, fluoride, and 13 metals as part of a state-funded program that provides assistance to low-income families. The authors' review of laboratory findings found that 47% of these wells had an exceedance of one or more health-based water quality standards. Test results for iron and coliform bacteria exceeded safe limits in 21% and 18% of these wells, respectively. In addition, 10% of the water samples from these wells were high in nitrate and 11% had an elevated result for aluminum, arsenic, lead, manganese, or strontium. The high percentage of unsafe test results emphasizes the importance of water quality monitoring to the health of nearly one million families including 300,000 Wisconsin children whose drinking water comes from a privately owned well.

  1. Towards reference architectures as an enabler for software ecosystems

    DEFF Research Database (Denmark)

    Knodel, Jens; Manikas, Konstantinos

    2016-01-01

    Software ecosystems - a topic with increasingly growing interest in academia and industry in the past decade - arguably revolutionized many aspects of industrial software engineering (business models, architectures, platforms, project executions, collaboration models, distribution of assets......, to name a few). Software ecosystems enable the contribution of external actors with distinct center a common technology and the potential distribution of the actor contributions to an existing user set. Reference architectures have been proven successful and beneficial for software product lines...... and traditional software development within distinct domains. They arguably come with a set of benefits that severely counterweights the additional effort of design and implementation. But what is the role of reference architectures in an ecosystem setting? In this position paper, we argue for the use...

  2. Continuing the promise: Recruiting and preparing Hmong-American educators for Central Wisconsin

    Directory of Open Access Journals (Sweden)

    Leslie McClain-Ruelle

    2006-01-01

    Full Text Available The state of Wisconsin, and in the broader context, the middle states of the United States experienced a large influx of Hmong families starting in the early 1980’s and into the 1990’s. With this influx a large number of young, Southeast Asian children entered the PK-12 classrooms, often with the support of bilingual aides. While many of the children flourished within this newer context, they were mostly guided in their classrooms by white, Anglo educators. Although theseeducators work to meet the needs of all children, there were few to no Hmong educators working with these same children in the PK-12 setting. At the same time, a number of Hmong young adults were serving as bilingual aides in these classrooms. Project Forward, a federally funded Title VII grant, has worked to create a shift in these roles, preparing Hmong college students to become educators in the PK-12 settings. In 1999, Central Wisconsin enrolled approximately3,200 Hmong children in the PK-12 schools; at the same time, Central Wisconsin employed merely seven Hmong teachers in the classrooms. The goal of the grant program described in this paper is to prepare teachers of Southeast Asian background for early childhood, elementary, secondary and K-12 classrooms. The Central Wisconsin grant has supported a total of 35 Southeast Asian students in their pursuit of teaching careers. Fulfilling the goal of preparingteachers who can serve as role models for Southeast Asian children in our schools has met with successes and struggles. This article presents consideration of the central factors affectingrecruitment, retention and preparation of Hmong pre-service teachers in Central Wisconsin. The article includes a brief historical examination of the immigration of the Hmong population intothe United States, a consideration of the Hmong culture as it affects recruitment and retention of pre-service teachers and evidence related to successes and struggles experienced by Project

  3. Bridge Scour Monitoring Methods at Three Sites in Wisconsin

    National Research Council Canada - National Science Library

    Walker, John F; Hughes, Peter E

    2005-01-01

    .... Geological Survey, in cooperation with the Wisconsin Department of Transportation, the Marathon County Highway Department, and the Jefferson County Highway Department, performed routine monitoring...

  4. RETHINKING HOUSING EDUCATION IN ARCHITECTURE SCHOOLS

    Directory of Open Access Journals (Sweden)

    Avi Friedman

    2010-07-01

    Full Text Available Architects are involved in only a small percentage of all built projects and are becoming marginalized in the huge home-building industry where other professions are moving in to profit from the need for affordable housing. The vast majority of homebuyers today view housing as a commodity and are unwilling to spend more on an architect-designed house. Architects must expand the market for their services to include a far greater percentage of new buildings. It is my contention that the new place for architects is in the design of speculative housing as expert consultant to the developer. The practice of architecture must change emphasis to consider more social and economic concerns. The attitudes and skills currently being taught in architecture schools must change to reflect the new needs of the profession. Architects must be taught behavioral psychology, demographics, and building economics to enable them to apply their knowledge to the market, thereby rendering the architect’s services indispensable to developers and the housing industry. Architectural education must play a key role in redefining the scope of the profession.

  5. Operability and location of Wisconsin's timber resource.

    Science.gov (United States)

    Jerold T. Hahn; Mark H. Hansen

    1989-01-01

    Data collected during the 1983 Wisconsin Statewide forest inventory were used to examine operability of the timber resource based on seven operability components. Operability is the ease or difficulty of managing or harvesting timber because of physical conditions in the stand or on the site.

  6. 78 FR 44596 - Notice of Inventory Completion: State Historical Society of Wisconsin, Madison, WI

    Science.gov (United States)

    2013-07-24

    ... address in this notice by August 23, 2013. ADDRESSES: Jennifer Kolb, Wisconsin Historical Museum, 30 North Carroll Street, Madison, WI 53703, telephone (608) 261-2461, email Jennifer.Kolb@wisconsinhistory.org... request to Jennifer Kolb, Wisconsin Historical Museum, 30 North Carroll Street, Madison, WI 53703...

  7. Knowledge Architect : A Tool Suite for Managing Software Architecture Knowledge

    NARCIS (Netherlands)

    Liang, Peng; Jansen, Anton; Avgeriou, Paris

    2009-01-01

    Management of software architecture knowledge (AK) is vital for improving an organization’s architectural capabilities. To support the architecting process within our industrial partner: Astron, the Dutch radio astronomy institute, we implemented the Knowledge Architect (KA): a tool suite for

  8. Advocacy and education in Wisconsin

    International Nuclear Information System (INIS)

    Wise, M.

    1986-01-01

    Wisconsin's Radioactive Waste Review Board is required by law to advocate for and educate the public on the high-level nuclear waste issue. The goal of its education program is to empower people by giving them information and skills. Environmental advocacy and public activism are part of the State's Progressive political tradition. The Board seeks and uses public input while developing education programs, and helps local areas organize committees to develop their own programs

  9. The University of Wisconsin OAO operating system

    Science.gov (United States)

    Heacox, H. C.; Mcnall, J. F.

    1972-01-01

    The Wisconsin OAO operating system is presented which consists of two parts: a computer program called HARUSPEX, which makes possible reasonably efficient and convenient operation of the package and ground operations equipment which provides real-time status monitoring, commanding and a quick-look at the data.

  10. Using business critical design rules to frame new architecture introduction in multi-architecture portfolios

    DEFF Research Database (Denmark)

    Løkkegaard, Martin; Mortensen, Niels Henrik; Hvam, Lars

    2018-01-01

    component sharing, or sharing critical design principles. This alignment is not trivial, as extensive design knowledge is needed to overview a portfolio with many, often highly different products and manufacturing lines. In this paper, we suggest establishing a frame of reference for new......When introducing new architectures to an industrial portfolio, counting multiple existing product and manufacturing solutions, time-to-market and investments in manufacturing equipment can be significantly reduced if new concepts are aligned with the existing portfolio. This can be done through......-product introduction based on several ‘game rules’, or Business Critical Design Rules (BCDRs), which denote the most critical features of the product and manufacturing architectures, and should be considered an obligatory reference for design when introducing new architectures. BCDRs are derived from the portfolio...

  11. Two College of Architecture and Urban Studies faculty members named most admired educators of 2008

    OpenAIRE

    Chadwick, Heather Riley

    2008-01-01

    Two School of Architecture + Design faculty, in Virginia Tech's College of Architecture and Urban Studies, have been named by the Design and Futures Council and the journal DesignIntelligence as two of 28 educators most admired and respected in the fields of interior design, interior architecture, architecture, design, architectural engineering, industrial design, and landscape architecture.

  12. Fundamentals of computer architecture and design

    CERN Document Server

    Bindal, Ahmet

    2017-01-01

    This textbook provides semester-length coverage of computer architecture and design, providing a strong foundation for students to understand modern computer system architecture and to apply these insights and principles to future computer designs.  It is based on the author’s decades of industrial experience with computer architecture and design, as well as with teaching students focused on pursuing careers in computer engineering.  Unlike a number of existing textbooks for this course, this one focuses not only on CPU architecture, but also covers in great detail in system buses, peripherals and memories.This book teaches every element in a computing system in two steps.  First, it introduces the functionality of each topic (and subtopics) and then goes into “from-scratch design” of a particular digital block from its architectural specifications using timing diagrams.  The author describes how the data-path of a certain digital block is generated using timin g diagrams, a method which most textbo...

  13. 75 FR 70026 - Notice of Inventory Completion: Wisconsin Historical Society, Museum Division, Madison, WI

    Science.gov (United States)

    2010-11-16

    ... with representatives of the Bad River Band of the Lake Superior Tribe of Chippewa Indians of the Bad... Division, is responsible for notifying the Bad River Band of the Lake Superior Tribe of Chippewa Indians of the Bad River Reservation, Wisconsin; Forest County Potawatomi Community, Wisconsin; Lac Courte...

  14. Advanced customization in architectural design and construction

    CERN Document Server

    Naboni, Roberto

    2015-01-01

    This book presents the state of the art in advanced customization within the sector of architectural design and construction, explaining important new technologies that are boosting design, product and process innovation and identifying the challenges to be confronted as we move toward a mass customization construction industry. Advanced machinery and software integration are discussed, as well as an overview of the manufacturing techniques offered through digital methods that are acquiring particular significance within the field of digital architecture. CNC machining, Robotic Fabrication, and Additive Manufacturing processes are all clearly explained, highlighting their ability to produce personalized architectural forms and unique construction components. Cutting-edge case studies in digitally fabricated architectural realizations are described and, looking towards the future, a new model of 100% customized architecture for design and construction is presented. The book is an excellent guide to the profoun...

  15. Application of Data Architecture Model in Enterprise Management

    Directory of Open Access Journals (Sweden)

    Shi Song

    2017-01-01

    Full Text Available Today is in the era of rapid development of information, data volume of high-speed expansion, it is difficult in the previous system for communication, sharing and integration. In order to integrate data resources, eliminate the “information island”, build enterprise development blueprints, people gradually realize the importance of top design. Many enterprises for their own development to establish their own enterprise architecture of the top design, and as its core data architecture model is also reflected in different industries according to different development. This paper mainly studies the data architecture model, expounds the role of data architecture model and its relationship.

  16. Successful Architectural Knowledge Sharing: Beware of Emotions

    Science.gov (United States)

    Poort, Eltjo R.; Pramono, Agung; Perdeck, Michiel; Clerc, Viktor; van Vliet, Hans

    This chapter presents the analysis and key findings of a survey on architectural knowledge sharing. The responses of 97 architects working in the Dutch IT Industry were analyzed by correlating practices and challenges with project size and success. Impact mechanisms between project size, project success, and architectural knowledge sharing practices and challenges were deduced based on reasoning, experience and literature. We find that architects run into numerous and diverse challenges sharing architectural knowledge, but that the only challenges that have a significant impact are the emotional challenges related to interpersonal relationships. Thus, architects should be careful when dealing with emotions in knowledge sharing.

  17. 75 FR 52369 - Notice of Inventory Completion: Wisconsin Historical Society, Museum Division, Madison, WI

    Science.gov (United States)

    2010-08-25

    ... member Indian tribes (Bad River Band of the Lake Superior Tribe of Chippewa Indians of the Bad River... Alliance and the Wisconsin Inter-tribal Repatriation Committee indicated that the Bad River Band of the Lake Superior Tribe of Chippewa Indians of the Bad River Reservation, Wisconsin, and Red Cliff Band of...

  18. Career satisfaction and retention risk among Wisconsin internists.

    Science.gov (United States)

    Giriyappa, Pradeep; Sullivan, Kandis K

    2009-09-01

    Physician career satisfaction has been studied extensively, but career satisfaction as it relates to retention is less well studied. The objective was to assess the relationship between career satisfaction and retention in primary care internal medicine physicians in Wisconsin. In this descriptive quantitative study, survey data was assessed for correlations between career satisfaction, risk to retention, and demographics. The survey included 1231 primary care internal medicine physicians in the Wisconsin Medical Directory (2007). Responses were measured by career satisfaction variables, and demographics and retention variables for the purpose of correlations and regression analysis. Survey responses included 573 physicians. An additional 85 physicians were disqualified. The final survey group included 1146 physicians for a response rate of 50%. A total of 116 physicians (20.2%) reported anticipating leaving their current position, 84 (14.7%) physicians reported anticipating leaving the career of medicine. Identified at risk for retention were 144 (25.1%) physicians. The lowest career satisfaction scores were reported in the areas of compensation (3.19) and practice (3.42) on a scale of 1 (very dissatisfied) to 5 (very satisfied). The highest correlations to retention were associated with practice, followed by compensation satisfaction. The level of significance for this study was identified as 0.05, and the P-value was 0.000. The study findings reveal a significant risk to the stability of continuity of care for patients, and may cost Wisconsin health care organizations more than $35 million in recruitment costs to replace departing physicians.

  19. Naval open systems architecture

    Science.gov (United States)

    Guertin, Nick; Womble, Brian; Haskell, Virginia

    2013-05-01

    For the past 8 years, the Navy has been working on transforming the acquisition practices of the Navy and Marine Corps toward Open Systems Architectures to open up our business, gain competitive advantage, improve warfighter performance, speed innovation to the fleet and deliver superior capability to the warfighter within a shrinking budget1. Why should Industry care? They should care because we in Government want the best Industry has to offer. Industry is in the business of pushing technology to greater and greater capabilities through innovation. Examples of innovations are on full display at this conference, such as exploring the impact of difficult environmental conditions on technical performance. Industry is creating the tools which will continue to give the Navy and Marine Corps important tactical advantages over our adversaries.

  20. SCADA Architecture for Natural Gas plant

    Directory of Open Access Journals (Sweden)

    Turc Traian

    2009-12-01

    Full Text Available The paper describes the Natural Gas Plant SCADA architecture. The main purpose of SCADA system is remote monitoring and controlling of any industrial plant. The SCADA hardware architecture is based on multi-dropping system allowing connecting a large number of different fiels devices. The SCADA Server gathers data from gas plant and stores data to a MtSQL database. The SCADA server is connected to other SCADA client application offers a intuitive and user-friendly HMI. The main benefit of using SCADA is real time displaying of gas plant state. The main contriobution of the authors consists in designing SCADA architecture based on multi-dropping system and Human Machine Interface.

  1. The Legal Status of Homemakers in Wisconsin.

    Science.gov (United States)

    Melli, Marygold Shire

    This report focuses on laws in the state of Wisconsin as they relate to homemakers. Four areas are discussed, each in separate sections: marriage, widowhood, divorce, and wife abuse. The section on marriage includes information on property rights, disability and death of homemaker, federal Equal Credit Opportunity Act, domicile, interspousal…

  2. Water-quality and lake-stage data for Wisconsin lakes, water year 2014

    Science.gov (United States)

    Manteufel, S. Bridgett; Robertson, Dale M.

    2017-05-25

    IntroductionThe U.S. Geological Survey (USGS), in cooperation with local and other agencies, collects data at selected lakes throughout Wisconsin. These data, accumulated over many years, provide a database for developing an improved understanding of the water quality of lakes. To make these data available to interested parties outside the USGS, the data are published annually in this report series. The locations of water-quality and lake-stage stations in Wisconsin for water year 2014 are shown in figure 1. A water year is the 12-month period from October 1 through September 30. It is designated by the calendar year in which it ends. Thus, the periodOctober 1, 2013, through September 30, 2014, is called “water year 2014.”The purpose of this report is to provide information about the chemical and physical characteristics of Wisconsin lakes. Data that have been collected at specific lakes, and information to aid in the interpretation of those data, are included in this report. Data collected include measurements of in-lake water quality and lake stage. Time series of Secchi depths, surface total phosphorus, and chlorophyll a concentrations collected during nonfrozen periods are included for many lakes. Graphs of vertical profiles of temperature, dissolved oxygen, pH, and specific conductance are included for sites where these parameters were measured. Descriptive information for each lake includes the location of the lake, area of the lake’s watershed, period for which data are available, revisions to previously published records, and pertinent remarks. Additional data, such as streamflow and water quality in tributary and outlet streams of some of the lakes, are published online at http://nwis.waterdata.usgs.gov/wi/nwis.Water-resources data, including stage and discharge data at most streamflow-gaging stations, are available online. The Wisconsin Water Science Center’s home page is at https://www.usgs.gov/centers/wisconsin-water-science-center. Information

  3. 78 FR 65875 - Approval and Promulgation of Air Quality Implementation Plans; Wisconsin; Removal of Gasoline...

    Science.gov (United States)

    2013-11-04

    ...] Approval and Promulgation of Air Quality Implementation Plans; Wisconsin; Removal of Gasoline Vapor... Administrative Code, Chapter NR 420 Control of Organic Compound Emissions from Petroleum and Gasoline Sources... FROM PETROLEUM AND GASOLINE SOURCES. NR 420.01 as published in the (Wisconsin) Register, February, 1990...

  4. Groundwater sampling methods using glass wool filtration to trace human enteric viruses in Madison, Wisconsin

    Science.gov (United States)

    Human enteric viruses have been detected in the Madison, Wisconsin deep municipal well system. Earlier projects by the Wisconsin Geological and Natural History Survey (WGNHS) have used glass wool filters to sample groundwater for these viruses directly from the deep municipal wells. Polymerase chain...

  5. Conceptual design supporting tool between architectural design office and its client

    NARCIS (Netherlands)

    Shen, JiangTao

    2012-01-01

    Accompanied with the continuation of rapid Chinese economic growth through the past decades, I have experienced great changes happened in the architectural design industry. Computer science and various architectural design theories had been widely applied; traditional design institutes, which based

  6. Wisconsin Public Schools at a Glance, 2016

    Science.gov (United States)

    Wisconsin Department of Public Instruction, 2016

    2016-01-01

    "Wisconsin Public Schools at a Glance" provides in a single page document statistical information on the following topics: (1) Total number of public schools (2015-16); (2) Student (2015-16); (3) Attendance & Graduation (2014-15);(4) Staff (2013-14); (5) School Funding; and (6) Student Performance (2014-15). [For the previous report…

  7. Revolution of Chinese architectural design at the new-type urbanization stage

    Directory of Open Access Journals (Sweden)

    Jianguo Wang

    2015-09-01

    Full Text Available Witnessing more than three decades of sustained and rapid economic growth, China has become a nation that enjoys the fastest rate of urbanization; the largest quantities of civil construction; the most obvious urban development to be “newer”, “bigger” and “higher”; and the most prosperous architectural design market worldwide. In terms of the construction industry, housing construction totals 31.3 billion square meters, occupying more than 70% of the floor area of the existing stock houses. It is safe to say that the construction industry significantly boosts GDP growth, expands the number of jobs, and improves the living conditions of the masses. Related to this is the need to end the architectural guidelines of the planned economy era economizing on food and clothing and instead step into a new historic stage allowing bold pursuit of architectural aesthetics and individuality. A group of architects who have social ideals, adhere faithfully to professional standards and pledge to pursue architectural innovation are active in China. Instead of simply converting the overwhelming opportunities brought to carry economic benefits, they dare to embrace the challenges imposed on enhancing architectural connotation and create a batch of high-level work that lives up to expectations of the era, marking the achievement of reform and rapid urbanization in China. Yet, as time goes on, the promotion of national development concepts, ideas of social consumption and the masses’ cultural level establishes new requirements for the architectural design industry, architects and architectural design works. An appeal is thus made against Chinese architects for a summary, reflection and proactive anticipation to respond to the new requirements of the era.

  8. Evaluating barnyard Best Management Practices in Wisconsin using upstream-downstream monitoring

    Science.gov (United States)

    Stuntebeck, Todd D.

    1995-01-01

    The Nonpoint Source Water Pollution Abatement Program was created in 1978 by the Wisconsin Legislature. The goal of the program is to improve and protect the water quality of lakes, streams, wetlands, and ground water within selected priority watersheds by controlling sources of nonpoint pollution. For each selected watershed, the Wisconsin Department of Natural Resources drafts a management plan that guides the implementation of pollution-control strategies known as Best Management Practices (BMP's). This plan summarizes resource and land-use inventories, describes the results of pollution-source modeling, and suggests pollution reduction goals. The U.S. Geological Survey, through a cooperative effort with the Wisconsin Department of Natural Resources, is monitoring water-quality improvements that result from the implementation of BMP's. The data collected are then compared to the watershed plans to assess progress and determine whether goals are being realized. This fact sheet describes the data-collection efforts, preliminary results, and planned data-analysis techniques of monitoring projects for pre-BMP conditions at two barnyards, one each on Otter Creek and Halfway Prairie Creek.

  9. Architecture evaluation of an agent-based music gathering application

    NARCIS (Netherlands)

    Breemen, van A.J.N.; Feijs, L.M.G.

    2003-01-01

    The software architecture determines for a critical part the success of an industrial application. In this context success should be understood in terms of so called ‘ilities’, such as interoperability, integrability and responsiveness. Now that agent research is most actual we notice that industry

  10. Stakeholders' Perceptions of Parcelization in Wisconsin's Northwoods

    Science.gov (United States)

    Mark G. Rickenbach; Paul H. Gobster

    2003-01-01

    Parcelization, the process by which relatively large forest ownerships become subdivided into smaller ones, is often related to changes in ownership and can bring changes to the use of the land. Landowners, resource professionals, and others interested in Wisconsin's Northwoods were asked their views on parcelization in a series of stakeholder forums. We analyzed...

  11. Application of Protocol-Oriented MVVM Architecture in iOS Development

    OpenAIRE

    Luong Nguyen, Khoi Nguyen

    2017-01-01

    The mobile application industry is fast paced. Requirements change, additions of new features occur on a daily basis and demand frequent code structure adjustment. Thus, a flexible and maintainable software architecture is often a key factor for an application’s success. The major objective of this thesis is to propose a practical use case of Protocol Oriented Model View View Model, an architecture inspired by the Protocol Oriented Programming paradigm. This thesis explains the architectur...

  12. An Evaluation of Illicit Stimulants and Metabolites in Wastewa ter Effluent and the Wisconsin River Along the Central Wisconsin River Basin

    Directory of Open Access Journals (Sweden)

    Erik S. Hendrickson

    2015-09-01

    Full Text Available The goals of the study were to develop a method for extracting and quantifying illicit stimulants and metabolites, methamphetamine, amphetamine, cocaine, and benzoylecogonine from wastewater effluent and surface water grab samples, and evaluate Central Wisconsin wastewater treatment plant’s (WWTP removal efficiency of compounds of interest. The method created used HLB solid-phase extraction (SPE cartridges to extract substances of interest and High Performance Liquid Chromatography tandem Mass Spectrometry (HPLC/MS/MS for quantification and qualification. All four wastewater effluent samples and three Wisconsin River samples had quantifiable concentrations of at least one analyte. Conclusions derived from the study were: The method created is effective for separating, quantifying, and identifying amphetamine, cocaine, and benzoylecognine from wastewater effluent and surface water grab samples, and each illicit stimulant and metabolite analyzed in this study were all quantified in wastewater effluent, indicating these compounds have the ability to survive WWTP.

  13. Molecular basis of angiosperm tree architecture.

    Science.gov (United States)

    Hollender, Courtney A; Dardick, Chris

    2015-04-01

    The architecture of trees greatly impacts the productivity of orchards and forestry plantations. Amassing greater knowledge on the molecular genetics that underlie tree form can benefit these industries, as well as contribute to basic knowledge of plant developmental biology. This review describes the fundamental components of branch architecture, a prominent aspect of tree structure, as well as genetic and hormonal influences inferred from studies in model plant systems and from trees with non-standard architectures. The bulk of the molecular and genetic data described here is from studies of fruit trees and poplar, as these species have been the primary subjects of investigation in this field of science. No claim to original US Government works. New Phytologist © 2014 New Phytologist Trust.

  14. Gray wolf exposure to emerging vector-borne diseases in Wisconsin with comparison to domestic dogs and humans

    Science.gov (United States)

    Jara, Rocio F.; Wydeven, Adrian P.; Samuel, Michael D.

    2016-01-01

    World-wide concern over emerging vector-borne diseases has increased in recent years for both animal and human health. In the United Sates, concern about vector-borne diseases in canines has focused on Lyme disease, anaplasmosis, ehrlichiosis, and heartworm which infect domestic and wild canids. Of these diseases, Lyme and anaplasmosis are also frequently diagnosed in humans. Gray wolves (Canis lupus) recolonized Wisconsin in the 1970s, and we evaluated their temporal and geographic patterns of exposure to these four vector-borne diseases in Wisconsin as the population expanded between 1985 and 2011. A high proportion of the Wisconsin wolves were exposed to the agents that cause Lyme (65.6%) and anaplasma (47.7%), and a smaller proportion to ehrlichiosis (5.7%) and infected with heartworm (9.2%). Wolf exposure to tick borne diseases was consistently higher in older animals. Wolf exposure was markedly higher than domestic dog (Canis familiaris) exposure for all 4 disease agents during 2001–2013. We found a cluster of wolf exposure to Borrelia burgdorferi in northwestern Wisconsin, which overlaps human and domestic dog clusters for the same pathogen. In addition, wolf exposure to Lyme disease in Wisconsin has increased, corresponding with the increasing human incidence of Lyme disease in a similar time period. Despite generally high prevalence of exposure none of these diseases appear to have slowed the growth of the Wisconsin wolf population.

  15. Preindustrial versus postindustrial Architecture and Building Techniques

    DEFF Research Database (Denmark)

    Vestergaard, Inge

    2014-01-01

    How can preindustrial architecture inspire sustainable thinking in postindustrial architectural design? How can we learn from experience and how can social, economic and environmental conditions give perspectives and guide a knowledge based evolution of basic experience towards modern industriali......How can preindustrial architecture inspire sustainable thinking in postindustrial architectural design? How can we learn from experience and how can social, economic and environmental conditions give perspectives and guide a knowledge based evolution of basic experience towards modern...... industrialized building processes? Identification of sustainable parameters related to change in society, to building technique and to comfort are illustrated through two Danish building types, which are different in time, but similar in function. One representing evolution and experience based countryside...... fisherman’s house built around year 1700; and second a frontrunner suburban family house built year 2008. The analysis involves architectural, technical and comfort matters and will state the levels of design, social conditions, sustainable and energy efficient parameters. Results will show lessons learned...

  16. Architecturally Reconfigurable Development of Mobile Games

    DEFF Research Database (Denmark)

    Zhang, Weishan

    2005-01-01

    . Mobile game domain variants could be handled uniformly and traced across all kinds of software assets. The architecture and configuration mechanism in our approach make optimizations that built into meta-components propagated to all product line members. We show this approach with an industrial Role-Playing-Game......Mobile game development must face the problem of multiple hardware and software platforms, which will bring large number of variants. To cut the development and maintenance efforts, in this paper, we present an architecturally reconfigurable software product line approach to develop mobile games...

  17. Image and Morphology in Modern Theory of Architecture

    Science.gov (United States)

    Yankovskaya, Y. S.; Merenkov, A. V.

    2017-11-01

    This paper is devoted to some important and fundamental problems of the modern Russian architectural theory. These problems are: methodological and technological retardation; substitution of the modern professional architectural theoretical knowledge by the humanitarian concepts; preference of the traditional historical or historical-theoretical research. One of the most probable ways is the formation of useful modern subject (and multi-subject)-oriented concepts in architecture. To get over the criticism and distrust of the architectural theory is possible through the recognition of an important role of the subject (architect, consumer, contractor, ruler, etc.) and direction of the practical tasks of the forming human environment in the today’s rapidly changing world and post-industrial society. In this article we consider the evolution of two basic concepts for the theory of architecture such as the image and morphology.

  18. Migrating to Cloud-Native Architectures Using Microservices: An Experience Report

    OpenAIRE

    Balalaie, Armin; Heydarnoori, Abbas; Jamshidi, Pooyan

    2015-01-01

    Migration to the cloud has been a popular topic in industry and academia in recent years. Despite many benefits that the cloud presents, such as high availability and scalability, most of the on-premise application architectures are not ready to fully exploit the benefits of this environment, and adapting them to this environment is a non-trivial task. Microservices have appeared recently as novel architectural styles that are native to the cloud. These cloud-native architectures can facilita...

  19. The Politics of Reforming School Finance in Wisconsin.

    Science.gov (United States)

    Geske, Terry G.

    This paper is primarily concerned with identifying and explicating the environmental forces and political factors responsible for legislative enactment of major school finance changes in Wisconsin in 1973. Easton's political systems theory serves as a conceptual framework for the study. In addition, Lindblom's leadership model, Truman's interest…

  20. Architectural and structural qualities in timber joints

    DEFF Research Database (Denmark)

    Christensen, Jesper Thøger; Christensen, Mogens Fiil; Damkilde, Lars

    2016-01-01

    Design of joints in timber structures is crucial to reach both elegant and structural efficient designs. Design of joints should therefore be an integral part of the conceptual design phase. Traditionally this is not the case, and joints are often solely designed and analysed in the engineering...... but also increase timbers competitiveness in the building industry. The paper is part of an ongoing research project aiming at providing tools for an integrated design process for timber structures. The focus of the paper is to identify how structure and its joints contributes to architecture and vice...... design phase. The result is joints that function structurally but do not add value to the design, and may even compromise the architectural ideas. With an approach, integrating both structural and architectural design from the beginning, one should not only gain better structures and architecture...

  1. High dynamic range imaging sensors and architectures

    CERN Document Server

    Darmont, Arnaud

    2013-01-01

    Illumination is a crucial element in many applications, matching the luminance of the scene with the operational range of a camera. When luminance cannot be adequately controlled, a high dynamic range (HDR) imaging system may be necessary. These systems are being increasingly used in automotive on-board systems, road traffic monitoring, and other industrial, security, and military applications. This book provides readers with an intermediate discussion of HDR image sensors and techniques for industrial and non-industrial applications. It describes various sensor and pixel architectures capable

  2. Timber resource of Wisconsin's Northwest Survey Unit, 1983.

    Science.gov (United States)

    W. Brad Smith

    1984-01-01

    The fourth inventory of the timber resource of the Northwest Wisconsin Survey Unit shows a 1.8% decline in commercial forest area and a 36% gain in growing-stock volume between 1968 and 1983. Presented are highlights and statistics on area, volume, growth, mortality, removals, utilization, and biomass.

  3. The burden of suicide and homicide of Wisconsin's children and youth.

    Science.gov (United States)

    Shiffler, Thomas; Hargarten, Stephen W; Withers, Richard L

    2005-01-01

    To describe the epidemiology of violent deaths (suicides and homicides) of children and youth in Wisconsin. Linked data from death certificates, coroners or medical examiners, Uniform Crime Reports, police case reports and crime laboratories were analyzed using SPSS 11.5. Analyses from 2000 to 2002 describe suicides and homicides of children and youth under age 25. Rates are per 100,000 population per year. A total of 585 persons under age 25 in Wisconsin died from suicide or homicide during 2000--2002. Suicides outnumbered homicides 323 (55%) to 262 (45%). Firearms were involved in 59% (n=344) of cases. Fatality rates increased with advancing age, ranging from 2.0 in 0-13 year olds to 26.9 in youth age 21-24. There were over twice as many violent deaths compared to cancer and infectious disease deaths combined (n=253). Suicides and homicides are a significant burden on the children and youth of Wisconsin. An investment in reducing this burden requires comprehensive data and informed programs and policies. We recommend that physicians and public health community leaders collaborate with the criminal justice community and policy makers to develop, implement, and evaluate prevention programs and policies.

  4. Brasfield and Wisconsin scoring systems have equal value as outcome assessment tools of cystic fibrosis lung disease

    Energy Technology Data Exchange (ETDEWEB)

    Cleveland, Robert H.; Stamoulis, Catherine; Sawicki, Gregory; Kelliher, Emma; Wood, Christopher; Zurakowski, David; Lee, Edward [Boston Children' s Hospital, Harvard Medical School, Department of Radiology, Boston, MA (United States); Zucker, Evan J. [Tufts Medical School, Boston, MA (United States)

    2014-05-15

    Several imaging-based scoring systems have been used as outcome measures in assessing the severity of cystic fibrosis (CF) lung disease. It has been shown that chest radiography performs equally to computed tomography (CT). There is the opinion that of the two most commonly used chest radiograph (CXR) systems, the Brasfield system is less sensitive and reliable than the Wisconsin system. This report assesses the reproducibility and reliability of the two systems. Thirty patients with CXRs during a 5-year period were randomly selected. One hundred eighty-two studies had data for all CXRs and pulmonary function tests (PFTs), Forced Expiratory Volume in One Second (FEV-1) and Forced Vital Capacity (FVC). PFT values closest to the date of each CXR were recorded. Four radiologists scored each image twice by both the Brasfield and Wisconsin systems. Intra- and inter-rater reliability, correlation with PFTs and direct correlation of the two systems were calculated. Intra-rater agreement: r = 0.86-0.99 Brasfield, r = 0.78-0.96 Wisconsin. Inter-rater agreement: 0.76-0.90 Brasfield, r = 0.74-0.97 Wisconsin. Brasfield vs. FEV-1: r = 0.55, vs. FVC r = 0.61. Wisconsin vs. FEV-1: r = 0.57, vs. FVC r = 0.66. Correlation of the two systems: r = 0.86 (all P < 0.001). The Brasfield and Wisconsin systems performed very similarly providing equally reproducible, robust and reliable measures. (orig.)

  5. Gray Wolf Exposure to Emerging Vector-Borne Diseases in Wisconsin with Comparison to Domestic Dogs and Humans.

    Directory of Open Access Journals (Sweden)

    Rocio F Jara

    Full Text Available World-wide concern over emerging vector-borne diseases has increased in recent years for both animal and human health. In the United Sates, concern about vector-borne diseases in canines has focused on Lyme disease, anaplasmosis, ehrlichiosis, and heartworm which infect domestic and wild canids. Of these diseases, Lyme and anaplasmosis are also frequently diagnosed in humans. Gray wolves (Canis lupus recolonized Wisconsin in the 1970s, and we evaluated their temporal and geographic patterns of exposure to these four vector-borne diseases in Wisconsin as the population expanded between 1985 and 2011. A high proportion of the Wisconsin wolves were exposed to the agents that cause Lyme (65.6% and anaplasma (47.7%, and a smaller proportion to ehrlichiosis (5.7% and infected with heartworm (9.2%. Wolf exposure to tick borne diseases was consistently higher in older animals. Wolf exposure was markedly higher than domestic dog (Canis familiaris exposure for all 4 disease agents during 2001-2013. We found a cluster of wolf exposure to Borrelia burgdorferi in northwestern Wisconsin, which overlaps human and domestic dog clusters for the same pathogen. In addition, wolf exposure to Lyme disease in Wisconsin has increased, corresponding with the increasing human incidence of Lyme disease in a similar time period. Despite generally high prevalence of exposure none of these diseases appear to have slowed the growth of the Wisconsin wolf population.

  6. Wisconsin Women and the Law, Second Edition. The Governor's Commission on the Status of Women.

    Science.gov (United States)

    Governor's Commission on the Status of Women, Madison, WI.

    This handbook is written to inform Wisconsin citizens of women's rights and responsibilities under Wisconsin and federal law. It is intended for use as general legal resource material. It is not intended to take the place of an attorney in the solution of individual legal problems. Each of the 12 chapters treats a particular subject or topic.…

  7. Generative Algorithmic Techniques for Architectural Design

    DEFF Research Database (Denmark)

    Larsen, Niels Martin

    2012-01-01

    Architectural design methodology is expanded through the ability to create bespoke computational methods as integrated parts of the design process. The rapid proliferation of digital production techniques within building industry provides new means for establishing seamless flows between digital...... form-generation and the realisation process. A tendency in recent practice shows an increased focus on developing unique tectonic solutions as a crucial ingredient in the design solution. These converging trajectories form the contextual basis for this thesis. In architectural design, digital tools....... The principles are further developed to form new modes of articulation in architectural design. Certain methods are contributions, which suggest a potential for future use and development. Thus, a method is directed towards bottom-up generation of surface topology through the use of an agentbased logic. Another...

  8. Space-Time and Architecture

    Science.gov (United States)

    Field, F.; Goodbun, J.; Watson, V.

    Architects have a role to play in interplanetary space that has barely yet been explored. The architectural community is largely unaware of this new territory, for which there is still no agreed method of practice. There is moreover a general confusion, in scientific and related fields, over what architects might actually do there today. Current extra-planetary designs generally fail to explore the dynamic and relational nature of space-time, and often reduce human habitation to a purely functional problem. This is compounded by a crisis over the representation (drawing) of space-time. The present work returns to first principles of architecture in order to realign them with current socio-economic and technological trends surrounding the space industry. What emerges is simultaneously the basis for an ecological space architecture, and the representational strategies necessary to draw it. We explore this approach through a work of design-based research that describes the construction of Ocean; a huge body of water formed by the collision of two asteroids at the Translunar Lagrange Point (L2), that would serve as a site for colonisation, and as a resource to fuel future missions. Ocean is an experimental model for extra-planetary space design and its representation, within the autonomous discipline of architecture.

  9. Architectures for Green-Field Supply Chain Integration: Supply Chain Integration Design

    OpenAIRE

    Radanliev, Petar

    2015-01-01

    This paper applied case study research to design architectures for green-field supply chain integration. The integration design is based on a case study of a supply chain integration of 5 companies, operating in different, but supply chain complimenting industry sectors. The case study research is applied to design and validate the architectures in a real world scenario. The supply\\ud chain integration architectures enable the conversion of individual into integrated strategies. The architect...

  10. Public Schooling in Southeast Wisconsin: 2013-2014 [Summary

    Science.gov (United States)

    Yeado, Joe; Schmidt, Jeff; Hart, Rebecca; Henken, Rob

    2014-01-01

    This summary from the "Public Schooling in Southeast Wisconsin: 2013-2014" full report presents the school district performance in a pull-out format. Definitions are provided for the column heading: (1) Total Operations Spending, (2) Property Tax Revenue, (3) Total Enrollment; (4) One-Year Change in Enrollment, (5) Minority Enrollment,…

  11. Tornadoes Strike Northern Wisconsin

    Science.gov (United States)

    2007-01-01

    A series of tornadoes ripped through the Upper Midwest region of the United States in the evening of June 7, 2007. At least five different tornadoes touched down in Wisconsin, according to the Associated Press, one of which tore through the Bear Paw Resort in northern Wisconsin. Despite dropping as much as fifteen centimeters (six inches) of rain in some places and baseball-size hail in others, authorities were reporting no deaths attributable to the storm system, and only a smattering of injuries, but considerable property damage in some areas. When the MODIS instrument on NASA's Terra satellite observed the area on June 9, 2007, the track torn through the woods by one of the tornadoes stands out quite clearly. This photo-like image uses data collected by MODIS in the normal human vision range to give a familiar natural-looking appearance. The landscape is largely a checkerboard of farms, towns, roads, and cities. The pale land is predominantly farmland where crops have not fully grown in yet. Dark blue shows the winding path of rivers and lakes dotting the landscape. The large blue lake on the east (right) side of the image is Lake Michigan. Towns and cities, including the city of Green Bay, are gray. To the north side, farmland gives way to dark green as land use shifts from agriculture to the Menominee Indian Reservation and Nicolet National Forest. The diagonal slash through the dark green forested land shows the tornado track. Bare land was revealed where the tornado tore down trees or stripped vegetation off the branches. The high-resolution image provided above is at MODIS' full spatial resolution (level of detail) of 250 meters per pixel. The MODIS Rapid Response System provides this image at additional resolutions.

  12. Comparison of Home Retrofit Programs in Wisconsin

    Energy Technology Data Exchange (ETDEWEB)

    Cunningham, Kerrie [Univ. of Minnesota, St. Paul, MN (United States). NorthernSTAR Building America Partnership; Hannigan, Eileen [Univ. of Minnesota, St. Paul, MN (United States). NorthernSTAR Building America Partnership

    2013-03-01

    To explore ways to reduce customer barriers and increase home retrofit completions, several different existing home retrofit models have been implemented in the state of Wisconsin. This study compared these programs' performance in terms of savings per home and program cost per home to assess the relative cost-effectiveness of each program design. However, given the many variations in these different programs, it is difficult to establish a fair comparison based on only a small number of metrics. Therefore, the overall purpose of the study is to document these programs' performance in a case study approach to look at general patterns of these metrics and other variables within the context of each program. This information can be used by energy efficiency program administrators and implementers to inform home retrofit program design. Six different program designs offered in Wisconsin for single-family energy efficiency improvements were included in the study. For each program, the research team provided information about the programs' approach and goals, characteristics, achievements and performance. The program models were then compared with performance results-program cost and energy savings-to help understand the overall strengths and weaknesses or challenges of each model.

  13. Comparison of Home Retrofit Programs in Wisconsin

    Energy Technology Data Exchange (ETDEWEB)

    Cunningham, K.; Hannigan, E.

    2013-03-01

    To explore ways to reduce customer barriers and increase home retrofit completions, several different existing home retrofit models have been implemented in the state of Wisconsin. This study compared these programs' performance in terms of savings per home and program cost per home to assess the relative cost-effectiveness of each program design. However, given the many variations in these different programs, it is difficult to establish a fair comparison based on only a small number of metrics. Therefore, the overall purpose of the study is to document these programs' performance in a case study approach to look at general patterns of these metrics and other variables within the context of each program. This information can be used by energy efficiency program administrators and implementers to inform home retrofit program design. Six different program designs offered in Wisconsin for single-family energy efficiency improvements were included in the study. For each program, the research team provided information about the programs' approach and goals, characteristics, achievements and performance. The program models were then compared with performance results -- program cost and energy savings -- to help understand the overall strengths and weaknesses or challenges of each model.

  14. Architecture Of High Speed Image Processing System

    Science.gov (United States)

    Konishi, Toshio; Hayashi, Hiroshi; Ohki, Tohru

    1988-01-01

    One of architectures for a high speed image processing system which corresponds to a new algorithm for a shape understanding is proposed. And the hardware system which is based on the archtecture was developed. Consideration points of the architecture are mainly that using processors should match with the processing sequence of the target image and that the developed system should be used practically in an industry. As the result, it was possible to perform each processing at a speed of 80 nano-seconds a pixel.

  15. Greening radio access networks using distributed base station architectures

    DEFF Research Database (Denmark)

    Kardaras, Georgios; Soler, José; Dittmann, Lars

    2010-01-01

    Several actions for developing environmentally friendly technologies have been taken in most industrial fields. Significant resources have also been devoted in mobile communications industry. Moving towards eco-friendly alternatives is primarily a social responsibility for network operators....... However besides this, increasing energy efficiency represents a key factor for reducing operating expenses and deploying cost effective mobile networks. This paper presents how distributed base station architectures can contribute in greening radio access networks. More specifically, the advantages...... energy saving. Different subsystems have to be coordinated real-time and intelligent network nodes supporting complicated functionalities are necessary. Distributed base station architectures are ideal for this purpose mainly because of their high degree of configurability and self...

  16. Mercury accumulation in transplanted Hypogymnia physodes lichens downwind of Wisconsin chlor-alkali plant

    Science.gov (United States)

    Makholm, M.M.; Bennett, J.P.

    1998-01-01

    Emissions of mercury from a chlor-alkali plant in central Wisconsin have raised concern about possible effects on biota in the area. Samples of the lichen Hypogymnia physodes, which no longer grows in the area, were transplanted from a site in northeastern Wisconsin and positioned on plastic stands at varying distances up to 1250 m from the plant and sampled for Hg quarterly for one year to test the hypothesis that Hg would be taken up by the lichens and would decline with distance. Average tissue concentrations were elevated when first sampled at three months and continued to increase at the nearest sites until the study ended after one year. Average concentrations after a year of exposure ranged from 4418 ppb at 250 m from the plant to 403 ppb at 1250 m from the plant. The decrease over distance followed a negative exponential pattern. Background concentrations at a control site in northern Wisconsin averaged 155 ppb.

  17. An Introduction to Architectural Surety(SM) Education

    Energy Technology Data Exchange (ETDEWEB)

    Matalucci, R.V.; Miyoshi, D.S.

    1998-09-01

    This report describes the Sandia activities in the developing field management approach to enhancing National Laboratories (Sandia) educational outreach of architectural and infrastructure surety, a risk the safety, security, and reliability of facilities, systems, and structures. It begins with a description of the field of architectural and infrastmcture surety, including Sandia's historical expertise and experience in nuclear weapons surety. An overview of the 1996 Sandia Workshop on Architectural SuretysM is then provided to reference the initiation of the various activities. This workshop established the need for a surety education program at the University level and recommended that Sandia develop the course material as soon as possible. Technical material was assembled and the course was offered at the University of New Mexico (UNM) during the 1997 spring semester. The bulk of this report accordingly summarizes the lecture material presented in this pioneering graduate-level course on Infrastructure Surety in the Civil Engineering Department at UNM. This groundbreaking class presented subject matter developed by experts from Sandia, and included additional information from guest lecturers from academia, government, and industry. Also included in this report are summaries of the term projects developed by the graduate students, an overview of the 1997 International Conference on Architectural Suretp: Assuring the Performance of Buildings and Injiastruchwes (co-sponsored by Sandia, the American Institute of Architects, and the American Society of Civil Engineers), and recommendations for further course work development. The U.S. Department of Energy provides support to this emerging field of architectural and infrastructure surety and recognizes its broad application to developing government, industry, and professional standards in the national interest.

  18. Determining climate change management priorities: A case study from Wisconsin

    Science.gov (United States)

    LeDee, Olivia E.; Ribic, Christine

    2015-01-01

    A burgeoning dialogue exists regarding how to allocate resources to maximize the likelihood of long-term biodiversity conservation within the context of climate change. To make effective decisions in natural resource management, an iterative, collaborative, and learning-based decision process may be more successful than a strictly consultative approach. One important, early step in a decision process is to identify priority species or systems. Although this promotes the conservation of select species or systems, it may inadvertently alter the future of non-target species and systems. We describe a process to screen terrestrial wildlife for potential sensitivity to climate change and then use the results to engage natural resource professionals in a process of identifying priorities for monitoring, research, and adaptation strategy implementation. We demonstrate this approach using a case study from Wisconsin. In Wisconsin, experts identified 23 out of 353 species with sufficient empirical research and management understanding to inform targeted action. Habitat management and management of hydrological conditions were the common strategies for targeted action. Although there may be an interest in adaptation strategy implementation for many species and systems, experts considered existing information inadequate to inform targeted action. According to experts, 40% of the vertebrate species in Wisconsin will require near-term intervention for climate adaptation. These results will inform state-wide conservation planning as well as regional efforts.

  19. Wisconsin Partnerships to Educate and Engage Public Audiences on Climate Change Topics

    Science.gov (United States)

    Mooney, M. E.; Ackerman, S.; Rowley, P.; Crowley Conn, K.

    2011-12-01

    The complexity and scale of climate change-related challenges requires more than one strategy to share meaningful information with public audiences. This presentation will discuss a few initiatives to engage the public originating from the University of Wisconsin-Madison. First, a local partnership between the Cooperative Institute for Meteorological Satellite Studies (CIMSS) and the Aldo Leopold Nature Center (ALNC), an informal learning center with a new climate change "classroom" which recently acquired a Science on a Sphere (SOS) exhibit. Second, an informal education project funded by the NOAA Office of Education coordinated by CIMSS in partnership with the national SOS Network with the goal of helping museum docents share meaningful interpretation of real-time weather and climate data. CIMSS staff has been conducting weather and climate discussions on a Magic Planet display for several years. This "mini-SOS" is powered by a solar panel on the roof, modeling the essential Sun-Earth connection and the first principle of climate literacy. However, the convenient proximity of CIMSS and ALNC provides a perfect opportunity to test "SOS-scale" talking points posted on a weekly docent blog to the benefit of the entire SOS Network. Two other Wisconsin projects of note include the Wisconsin Initiative on Climate Change Impacts, a partnership between the University and the Wisconsin Department of Natural Resources, and a pilot project between CIMSS and NOAA's National Weather Service to engage storm spotters in climate mitigation and stewardship. Ideally, the synergistic benefits and lessons learned from these collaborations can inform similar efforts in order to galvanize meaningful responses to climate change.

  20. From green architecture to architectural green

    DEFF Research Database (Denmark)

    Earon, Ofri

    2011-01-01

    that describes the architectural exclusivity of this particular architecture genre. The adjective green expresses architectural qualities differentiating green architecture from none-green architecture. Currently, adding trees and vegetation to the building’s facade is the main architectural characteristics...... they have overshadowed the architectural potential of green architecture. The paper questions how a green space should perform, look like and function. Two examples are chosen to demonstrate thorough integrations between green and space. The examples are public buildings categorized as pavilions. One......The paper investigates the topic of green architecture from an architectural point of view and not an energy point of view. The purpose of the paper is to establish a debate about the architectural language and spatial characteristics of green architecture. In this light, green becomes an adjective...

  1. SMES developments at the University of Wisconsin

    International Nuclear Information System (INIS)

    Boom, R.W.; Abdelsalam, M.K.; Eyssa, Y.; Hilal, M.; Huang, X.; McIntosh, G.E.; Pfotenhauer, J.

    1988-01-01

    This paper reports on a long term SMES program in the Applied Superconductivity Center (ASC) in progress at the University of Wisconsin since 1970. The present principal interest in SMES stems from the US DNA-SDI program to build an engineering test model (ETM) for utility and government use. This paper is a review of SMES design highlights and of some small scale SMES studies

  2. Analysis of Employment Flow of Landscape Architecture Graduates in Agricultural Universities

    Science.gov (United States)

    Yao, Xia; He, Linchun

    2012-01-01

    A statistical analysis of employment flow of landscape architecture graduates was conducted on the employment data of graduates major in landscape architecture in 2008 to 2011. The employment flow of graduates was to be admitted to graduate students, industrial direction and regional distribution, etc. Then, the features of talent flow and factors…

  3. Model Driven Architecture: Foundations and Applications

    NARCIS (Netherlands)

    Rensink, Arend

    The OMG's Model Driven Architecture (MDA) initiative has been the focus of much attention in both academia and industry, due to its promise of more rapid and consistent software development through the increased use of models. In order for MDA to reach its full potential, the ability to manipulate

  4. Architecture on Architecture

    DEFF Research Database (Denmark)

    Olesen, Karen

    2016-01-01

    that is not scientific or academic but is more like a latent body of data that we find embedded in existing works of architecture. This information, it is argued, is not limited by the historical context of the work. It can be thought of as a virtual capacity – a reservoir of spatial configurations that can...... correlation between the study of existing architectures and the training of competences to design for present-day realities.......This paper will discuss the challenges faced by architectural education today. It takes as its starting point the double commitment of any school of architecture: on the one hand the task of preserving the particular knowledge that belongs to the discipline of architecture, and on the other hand...

  5. A comparison of Wisconsin neonatal intensive care units with national data on outcomes and practices.

    Science.gov (United States)

    Hagen, Erika W; Sadek-Badawi, Mona; Albanese, Aggie; Palta, Mari

    2008-11-01

    Improvements in neonatal care over the past 3 decades have increased survival of infants at lower birthweights and gestational ages. However, outcomes and practices vary considerably between hospitals. To describe maternal and infant characteristics, neonatal intensive care units (NICU) practices, morbidity, and mortality in Wisconsin NICUs, and to compare outcomes in Wisconsin to the National Institute of Child Health and Human Development network of large academic medical center NICUs. The Newborn Lung Project Statewide Cohort is a prospective observational study of all very low birthweight (< or =1500 grams) infants admitted during 2003 and 2004 to the 16 level III NICUs in Wisconsin. Anonymous data were collected for all admitted infants (N=1463). Major neonatal morbidities, including bronchopulmonary dysplasia (BPD), intraventricular hemorrhage (IVH), necrotizing enterocolitis (NEC), and retinopathy of prematurity (ROP) were evaluated. The overall incidence of BPD was 24% (8%-56% between NICUs); IVH incidence was 23% (9%-41%); the incidence of NEC was 7% (0%-21%); and the incidence of grade III or higher ROP was 10% (0%-35%). The incidence rates of major neonatal morbidities in Wisconsin were similar to those of a national network of academic NICUs.

  6. Preserving urban objects of historicaland architectural heritage

    OpenAIRE

    Bal'zannikova Ekaterina Mikhailovna

    2014-01-01

    Large cities of central Russia were built under the influence of the factors that played an important role in protecting their population; natural resources and opportunities for trading were also essential. The industrial development and construction of large industrial facilities were significant for the formation of urban environment. As a result architectural monuments of great historical value that have a significant influence on the formation of the modern city image were preserved.Nowa...

  7. Preserving urban objects of historicaland architectural heritage

    Directory of Open Access Journals (Sweden)

    Bal'zannikova Ekaterina Mikhailovna

    2014-01-01

    Full Text Available Large cities of central Russia were built under the influence of the factors that played an important role in protecting their population; natural resources and opportunities for trading were also essential. The industrial development and construction of large industrial facilities were significant for the formation of urban environment. As a result architectural monuments of great historical value that have a significant influence on the formation of the modern city image were preserved.Nowadays, a great number of buildings of historical and architectural heritage turned out to be in poor condition. Funding and its efficient use are rational means of saving the most valuable objects of historical and cultural heritage. In order to do this it is necessary to solve the problems of developing complex and effective measures for preserving these objectsThe existing method of preserving urban objects does not focus on urban architectural objects of historical and architectural value. It does not cover the study of urban development features in architectural and town-planning environment surrounding this object, it does not determine the historical and architectural value of the object and it does not identify the relationship of the object and the surrounding objects as well as architectural frame of the total area. That is why the existing method cannot be considered an appropriate system for preserving the objects of historical and architectural heritage.In order to avoid the disadvantages mentioned above and to increase tourist interest to the architecturally valuable buildings in urban areas, the author has proposed a complex approach to improve the method of reconstructing urban objects of great historical and architectural significance.The existing method of preserving historical objects includes the preparatory period of studying the degree of historical and architectural heritage wear and decay, developing the techniques for strengthening

  8. Tree seed handling, processing, testing, and storage at Hayward State Nursery, Wisconsin Department of Natural Resources

    Science.gov (United States)

    Gordon Christians

    2008-01-01

    The Hayward State Nursery, Wisconsin grows more than 40 species from seeds. Up to 6000 bushels of raw unprocessed tree and shrub seeds are collected each year, and all seeds are collected in Wisconsin or adjacent states. All white spruce (Picea glauca) and some white pine seeds (Pinus strobus) are collected from orchards containing...

  9. Space Mobile Network: A Near Earth Communication and Navigation Architecture

    Science.gov (United States)

    Israel, Dave J.; Heckler, Greg; Menrad, Robert J.

    2016-01-01

    This paper describes a Space Mobile Network architecture, the result of a recently completed NASA study exploring architectural concepts to produce a vision for the future Near Earth communications and navigation systems. The Space Mobile Network (SMN) incorporates technologies, such as Disruption Tolerant Networking (DTN) and optical communications, and new operations concepts, such as User Initiated Services, to provide user services analogous to a terrestrial smartphone user. The paper will describe the SMN Architecture, envisioned future operations concepts, opportunities for industry and international collaboration and interoperability, and technology development areas and goals.

  10. Water-quality and lake-stage data for Wisconsin lakes, water years 2012–2013

    Science.gov (United States)

    Manteufel, S. Bridgett; Robertson, Dale M.

    2017-05-25

    IntroductionThe U.S. Geological Survey (USGS), in cooperation with local and other agencies, collects data at selected lakes throughout Wisconsin. These data, accumulated over many years, provide a data base for developing an improved understanding of the water quality of lakes. To make these data available to interested parties outside the USGS, the data are published annually in this report series. The locations of water-quality and lake-stage stations in Wisconsin for water year 2012 are shown in figure 1. A water year is the 12-month period from October 1 through September 30. It is designated by the calendar year in which it ends. Thus, the period October 1, 2011 through September 30, 2012, is called “water year 2012.”The purpose of this report is to provide information about the chemical and physical characteristics of Wisconsin lakes. Data that have been collected at specific lakes, and information to aid in the interpretation of those data, are included in this report. Data collected include measurements of in-lake water quality and lake stage. Time series of Secchi depths, surface total phosphorus and chlorophyll a concentrations collected during non-frozen periods are included for all lakes. Graphs of vertical profiles of temperature, dissolved oxygen, pH, and specific conductance are included for sites where these parameters were measured. Descriptive information for each lake includes: location of the lake, area of the lake’s watershed, period for which data are available, revisions to previously published records, and pertinent remarks. Additional data, such as streamflow and water quality in tributary and outlet streams of some of the lakes, are published online at http://nwis.waterdata.usgs.gov/wi/nwis.Water-resources data, including stage and discharge data at most streamflow-gaging stations, are available online. The Wisconsin Water Science Center’s home page is at https://www.usgs.gov/centers/wisconsin-water-science-center. Information on

  11. A flexible architecture for advanced process control solutions

    Science.gov (United States)

    Faron, Kamyar; Iourovitski, Ilia

    2005-05-01

    Advanced Process Control (APC) is now mainstream practice in the semiconductor manufacturing industry. Over the past decade and a half APC has evolved from a "good idea", and "wouldn"t it be great" concept to mandatory manufacturing practice. APC developments have primarily dealt with two major thrusts, algorithms and infrastructure, and often the line between them has been blurred. The algorithms have evolved from very simple single variable solutions to sophisticated and cutting edge adaptive multivariable (input and output) solutions. Spending patterns in recent times have demanded that the economics of a comprehensive APC infrastructure be completely justified for any and all cost conscious manufacturers. There are studies suggesting integration costs as high as 60% of the total APC solution costs. Such cost prohibitive figures clearly diminish the return on APC investments. This has limited the acceptance and development of pure APC infrastructure solutions for many fabs. Modern APC solution architectures must satisfy the wide array of requirements from very manual R&D environments to very advanced and automated "lights out" manufacturing facilities. A majority of commercially available control solutions and most in house developed solutions lack important attributes of scalability, flexibility, and adaptability and hence require significant resources for integration, deployment, and maintenance. Many APC improvement efforts have been abandoned and delayed due to legacy systems and inadequate architectural design. Recent advancements (Service Oriented Architectures) in the software industry have delivered ideal technologies for delivering scalable, flexible, and reliable solutions that can seamlessly integrate into any fabs" existing system and business practices. In this publication we shall evaluate the various attributes of the architectures required by fabs and illustrate the benefits of a Service Oriented Architecture to satisfy these requirements. Blue

  12. Organizational Learning Supported by Reference Architecture Models

    DEFF Research Database (Denmark)

    Nardello, Marco; Møller, Charles; Gøtze, John

    2017-01-01

    The wave of the fourth industrial revolution (Industry 4.0) is bringing a new vision of the manufacturing industry. In manufacturing, one of the buzzwords of the moment is “Smart production”. Smart production involves manufacturing equipment with many sensors that can generate and transmit large...... amounts of data. These data and information from manufacturing operations are however not shared in the organization. Therefore the organization is not using them to learn and improve their operations. To address this problem, the authors implemented in an Industry 4.0 laboratory an instance...... of an emerging technical standard specific for the manufacturing industry. Global manufacturing experts consider the Reference Architecture Model Industry 4.0 (RAMI4.0) as one of the corner stones for the implementation of Industry 4.0. The instantiation contributed to organizational learning in the laboratory...

  13. A Citizen Science Program for Monitoring Lake Stages in Northern Wisconsin

    Science.gov (United States)

    Kretschmann, A.; Drum, A.; Rubsam, J.; Watras, C. J.; Cellar-Rossler, A.

    2011-12-01

    Historical data indicate that surface water levels in northern Wisconsin are fluctuating more now than they did in the recent past. In the northern highland lake district of Vilas County, Wisconsin, concern about record low lake levels in 2008 spurred local citizens and lake associations to form a lake level monitoring network comprising citizen scientists. The network is administered by the North Lakeland Discovery Center (NLDC, a local NGO) and is supported by a grant from the Citizen Science Monitoring Program of the Wisconsin Department of Natural Resources (WDNR). With technical guidance from limnologists at neighboring UW-Madison Trout Lake Research Station, citizen scientists have installed geographic benchmarks and staff gauges on 26 area lakes. The project engages citizen and student science participants including homeowners, non-profit organization member-participants, and local schools. Each spring, staff gauges are installed and referenced to fixed benchmarks after ice off by NLDC and dedicated volunteers. Volunteers read and record staff gauges on a weekly basis during the ice-free season; and maintain log books recording lake levels to the nearest 0.5 cm. At the end of the season, before ice on, gauges are removed and log books are collected by the NLDC coordinator. Data is compiled and submitted to a database management system, coordinated within the Wisconsin Surface Water Integrated Monitoring System (SWIMS), a statewide information system managed by the WDNR in Madison. Furthermore, NLDC is collaborating with the SWIMS database manager to develop data entry screens based on records collected by citizen scientists. This program is the first of its kind in Wisconsin to utilize citizen scientists to collect lake level data. The retention rate for volunteers has been 100% over the three years since inception, and the program has expanded from four lakes in 2008 to twenty-six lakes in 2011. NLDC stresses the importance of long-term monitoring and the

  14. Certification Manual for Wisconsin Public Librarians. Bulletin No. 94111.

    Science.gov (United States)

    Lamb, Donald K.

    This manual contains the guidelines and procedures for public librarian certification and certification renewal in Wisconsin. Certification is not required for library personnel other than administrators, but nonadministrators may apply for certification at the level for which they are eligible. Requirements for voluntary library certification are…

  15. New Energy Architecture. Myanmar

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2013-06-15

    A global transition towards a new energy architecture is under way, driven by countries' need to respond to the changing dynamics of economic growth, environmental sustainability and energy security. The World Economic Forum, in collaboration with Accenture, has created the New Energy Architecture Initiative to address and accelerate this transition. The Initiative supports the development of national strategies and policy frameworks as countries seek to achieve the combined goals of energy security and access, sustainability, and economic growth and development. The World Economic Forum has formed a partnership with the Ministry of Energy of Myanmar to help apply the Initiative's approach to this developing and resource-rich nation. The Asian Development Bank and the World Economic Forum's Project Adviser, Accenture, have collaborated with the Forum on this consultation process, and have been supported by relevant government, industry and civil society stakeholders. The consultation process aims to understand the nation's current energy architecture challenges and provide an overview of a path to a New Energy Architecture through a series of insights. These insights could form the basis for a long-term multistakeholder roadmap to build Myanmar's energy sector in a way that is secure and sustainable, and promotes economic growth as the country makes its democratic transition. While not all recommendations can be implemented in the near term, they do provide options for creating a prioritized roadmap for Myanmar's energy transition. This report is the culmination of a nine-month multistakeholder process investigating Myanmar's energy architecture. Over the course of many visits to the country, the team has conducted numerous interviews, multistakeholder workshops, and learning and data-gathering exercises to ensure a comprehensive range of information and views. The team has also engaged with a variety of stakeholders to better inform their findings, which have come

  16. New Energy Architecture. Myanmar

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2013-06-15

    A global transition towards a new energy architecture is under way, driven by countries' need to respond to the changing dynamics of economic growth, environmental sustainability and energy security. The World Economic Forum, in collaboration with Accenture, has created the New Energy Architecture Initiative to address and accelerate this transition. The Initiative supports the development of national strategies and policy frameworks as countries seek to achieve the combined goals of energy security and access, sustainability, and economic growth and development. The World Economic Forum has formed a partnership with the Ministry of Energy of Myanmar to help apply the Initiative's approach to this developing and resource-rich nation. The Asian Development Bank and the World Economic Forum's Project Adviser, Accenture, have collaborated with the Forum on this consultation process, and have been supported by relevant government, industry and civil society stakeholders. The consultation process aims to understand the nation's current energy architecture challenges and provide an overview of a path to a New Energy Architecture through a series of insights. These insights could form the basis for a long-term multistakeholder roadmap to build Myanmar's energy sector in a way that is secure and sustainable, and promotes economic growth as the country makes its democratic transition. While not all recommendations can be implemented in the near term, they do provide options for creating a prioritized roadmap for Myanmar's energy transition. This report is the culmination of a nine-month multistakeholder process investigating Myanmar's energy architecture. Over the course of many visits to the country, the team has conducted numerous interviews, multistakeholder workshops, and learning and data-gathering exercises to ensure a comprehensive range of information and views. The team has also engaged with a variety of stakeholders to better

  17. Macro-economic factors influencing the architectural business model shift in the pharmaceutical industry.

    Science.gov (United States)

    Dierks, Raphaela Marie Louisa; Bruyère, Olivier; Reginster, Jean-Yves; Richy, Florent-Frederic

    2016-10-01

    Technological innovations, new regulations, increasing costs of drug productions and new demands are only few key drivers of a projected alternation in the pharmaceutical industry. The purpose of this review is to understand the macro economic factors responsible for the business model revolution to possess a competitive advantage over market players. Areas covered: Existing literature on macro-economic factors changing the pharmaceutical landscape has been reviewed to present a clear image of the current market environment. Expert commentary: Literature shows that pharmaceutical companies are facing an architectural alteration, however the evidence on the rationale driving the transformation is outstanding. Merger & Acquisitions (M&A) deals and collaborations are headlining the papers. Q1 2016 did show a major slowdown in M&A deals by volume since 2013 (with deal cancellations of Pfizer and Allergan, or the downfall of Valeant), but pharmaceutical analysts remain confident that this shortfall was a consequence of the equity market volatility. It seems likely that the shift to an M&A model will become apparent during the remainder of 2016, with deal announcements of Abbott Laboratories, AbbVie and Sanofi worth USD 45billion showing the appetite of big pharma companies to shift from the fully vertical integrated business model to more horizontal business models.

  18. Factors Affecting Physician Satisfaction and Wisconsin Medical Society Strategies to Drive Change.

    Science.gov (United States)

    Coleman, Michele; Dexter, Donn; Nankivil, Nancy

    2015-08-01

    Physicians' dissatisfaction in their work is increasing, which is affecting the stability of health care in America. The Wisconsin Medical Society (Society) surveyed 1016 Wisconsin physicians to determine the source of their dissatisfaction. The survey results indicate Wisconsin physicians are satisfied when it comes to practice environment, work-life balance, and income. In addition, they are extremely satisfied when it comes to rating their ability to provide high quality care, and they have identified some benefits related to the adoption of electronic health records. However, they are feeling burned out, very unsatisfied with the amount of time spent in direct patient care compared to indirect patient care, and that they are spending too much time on administrative and data entry tasks. In terms of future workforce, many physicians are either unsure or would not recommend the profession to a prospective medical student. Electronic health records serve as both a satisfier and dissatisfier and as a potential driver for future physician satisfaction interventions. Changes at the institutional, organizational, and individual levels potentially could address the identified dissatisfiers and build upon the satisfiers. The Society identifies 12 strategies to improve upon the physician experience.

  19. Utilizing Rapid Prototyping for Architectural Modeling

    Science.gov (United States)

    Kirton, E. F.; Lavoie, S. D.

    2006-01-01

    This paper will discuss our approach to, success with and future direction in rapid prototyping for architectural modeling. The premise that this emerging technology has broad and exciting applications in the building design and construction industry will be supported by visual and physical evidence. This evidence will be presented in the form of…

  20. Wisconsin Certification Manual for Public Librarians. Bulletin No. 7075.

    Science.gov (United States)

    Wisconsin State Dept. of Public Instruction, Madison. Div. of Library Services.

    Designed to be used as a guide for public librarians and boards of trustees in meeting the requirements of Wisconsin's public librarian certification law, this manual is divided into two major sections covering public librarian certification and certification renewal/continuing education requirements. The first section includes discussions of…

  1. Characterization of suspended solids and total phosphorus loadings from small watersheds in Wisconsin

    Science.gov (United States)

    Danz, Mari E.; Corsi, Steven R.; Graczyk, David J.; Bannerman, Roger T.

    2010-01-01

    Knowledge of the daily, monthly, and yearly distribution of contaminant loadings and streamflow can be critical for the successful implementation and evaluation of water-quality management practices. Loading data for solids (suspended sediment and total suspended solids) and total phosphorus and streamflow data for 23 watersheds were summarized for four ecoregions of Wisconsin: the Driftless Area Ecoregion, the Northern Lakes and Forests Ecoregion, the North Central Hardwoods Ecoregion, and the Southeastern Wisconsin Till Plains Ecoregion. The Northern Lakes and Forests and the North Central Hardwoods Ecoregions were combined into one region for analysis due to a lack of sufficient data in each region. Urban watersheds, all located in the Southeastern Wisconsin Till Plains, were analyzed separately from rural watersheds as the Rural Southeastern Wisconsin Till Plains region and the Urban Southeastern Wisconsin Till Plains region. Results provide information on the distribution of loadings and streamflow between base flow and stormflow, the timing of loadings and streamflow throughout the year, and information regarding the number of days in which the majority of the annual loading is transported. The average contribution to annual solids loading from stormflow periods for the Driftless Area Ecoregion was 84 percent, the Northern Lakes and Forests/North Central Hardwoods region was 71 percent, the Rural Southeastern Wisconsin Till Plains region was 70 percent, and the Urban Southeastern Wisconsin Till Plains region was 90 percent. The average contributions to annual total phosphorus loading from stormflow periods were 72, 49, 61, and 76 percent for each of the respective regions. The average contributions to annual streamflow from stormflow periods are 20, 23, 31, and 50 percent for each of the respective regions. In all regions, the most substantial loading contributions for solids were in the late winter (February through March), spring (April through May), and

  2. Assessing the Workforce Development Needs of Healthcare Employers in Southeastern Wisconsin. Research Brief. Volume 98, Number 3

    Science.gov (United States)

    Million, Laura

    2010-01-01

    Despite near-record unemployment rates in the region, southeast Wisconsin's healthcare sector faces a distinctive challenge: finding sufficient numbers of qualified and trained workers to fill current and future job openings. A May 2009 University of Wisconsin-Milwaukee analysis found that one out of every four full-time job openings and one out…

  3. Ecosystem vulnerability assessment and synthesis: a report from the Climate Change Response Framework Project in northern Wisconsin

    Science.gov (United States)

    Chris Swanston; Maria Janowiak; Louis Iverson; Linda Parker; David Mladenoff; Leslie Brandt; Patricia Butler; Matt St. Pierre; Anantha Prasad; Stephen Matthews; Matthew Peters; Dale Higgins; Avery Dorland

    2011-01-01

    The forests of northern Wisconsin will likely experience dramatic changes over the next 100 years as a result of climate change. This assessment evaluates key forest ecosystem vulnerabilities to climate change across northern Wisconsin under a range of future climate scenarios. Warmer temperatures and shifting precipitation patterns are expected to influence ecosystem...

  4. Enhanced Flexibility and Reusability through State Machine-Based Architectures for Multisensor Intelligent Robotics

    Directory of Open Access Journals (Sweden)

    Héctor Herrero

    2017-05-01

    Full Text Available This paper presents a state machine-based architecture, which enhances the flexibility and reusability of industrial robots, more concretely dual-arm multisensor robots. The proposed architecture, in addition to allowing absolute control of the execution, eases the programming of new applications by increasing the reusability of the developed modules. Through an easy-to-use graphical user interface, operators are able to create, modify, reuse and maintain industrial processes, increasing the flexibility of the cell. Moreover, the proposed approach is applied in a real use case in order to demonstrate its capabilities and feasibility in industrial environments. A comparative analysis is presented for evaluating the presented approach versus traditional robot programming techniques.

  5. Phosphorus Loading and Compositional Characteristics in Eight-Mile Run Watershed, Wisconsin

    National Research Council Canada - National Science Library

    James, William

    2004-01-01

    The purpose of this research was to describe and quantify biologically labile and refractory phosphorus runoff in Eight-Mile Run, a small watershed in west-central Wisconsin that is impacted by dairy...

  6. Trustee Essentials: A Handbook for Wisconsin Public Library Trustees.

    Science.gov (United States)

    Wisconsin State Dept. of Public Instruction, Madison.

    This handbook for Trustees of the Wisconsin Public Library describes in detail the tasks involved in being a library trustee. The handbook comprises a number of "Trustee Essentials" that cover the basic essential information needed by Trustees, as well as sources of additional information. Contents include: The Trustee Job Description;…

  7. Queer & Ally Youth Involvement in the Fair Wisconsin Campaign

    Science.gov (United States)

    Stiegler, Sam

    2008-01-01

    This article discusses the role and experience of queer youth and allies in the Fair Wisconsin campaign that fought against the marriage amendment to that state's constitution. It illustrates how LGBT and ally youth involvement can be incorporated into other organizations. Following an explanation of the campaign, are narratives of two…

  8. Digital Learning Compass: Distance Education State Almanac 2017. Wisconsin

    Science.gov (United States)

    Seaman, Julia E.; Seaman, Jeff

    2017-01-01

    This brief report uses data collected under the U.S. Department of Education's National Center for Educational Statistics (NCES) Integrated Postsecondary Education Data System (IPEDS) Fall Enrollment survey to highlight distance education data in the state of Wisconsin. The sample for this analysis is comprised of all active, degree-granting…

  9. Service Oriented Architecture for High Level Applications

    International Nuclear Information System (INIS)

    Chu, P.

    2012-01-01

    Standalone high level applications often suffer from poor performance and reliability due to lengthy initialization, heavy computation and rapid graphical update. Service-oriented architecture (SOA) is trying to separate the initialization and computation from applications and to distribute such work to various service providers. Heavy computation such as beam tracking will be done periodically on a dedicated server and data will be available to client applications at all time. Industrial standard service architecture can help to improve the performance, reliability and maintainability of the service. Robustness will also be improved by reducing the complexity of individual client applications.

  10. Implementing Interoperability in the Seafood Industry: Learning from Experiences in Other Sectors.

    Science.gov (United States)

    Bhatt, Tejas; Gooch, Martin; Dent, Benjamin; Sylvia, Gilbert

    2017-08-01

    Interoperability of communication and information technologies within and between businesses operating along supply chains is being pursued and implemented in numerous industries worldwide to increase the efficiency and effectiveness of operations. The desire for greater interoperability is also driven by the need to reduce business risk through more informed management decisions. Interoperability is achieved by the development of a technology architecture that guides the design and implementation of communication systems existing within individual businesses and between businesses comprising the supply chain. Technology architectures are developed through a purposeful dialogue about why the architecture is required, the benefits and opportunities that the architecture offers the industry, and how the architecture will translate into practical results. An assessment of how the finance, travel, and health industries and a sector of the food industry-fresh produce-have implemented interoperability was conducted to identify lessons learned that can aid the development of interoperability in the seafood industry. The findings include identification of the need for strong, effective governance during the establishment and operation of an interoperability initiative to ensure the existence of common protocols and standards. The resulting insights were distilled into a series of principles for enabling syntactic and semantic interoperability in any industry, which we summarize in this article. Categorized as "structural," "operational," and "integrative," the principles describe requirements and solutions that are pivotal to enabling businesses to create and capture value from full chain interoperability. The principles are also fundamental to allowing governments and advocacy groups to use traceability for public good. © 2017 Institute of Food Technologists®.

  11. Similar performance of Brasfield and Wisconsin scoring systems in young children with cystic fibrosis

    Energy Technology Data Exchange (ETDEWEB)

    Cleveland, Robert H.; Stamoulis, Catherine [Boston Children' s Hospital, Harvard Medical School, Department of Radiology, Boston, MA (United States); Sawicki, Gregory S. [Boston Children' s Hospital, Harvard Medical School, Division of Respiratory Diseases, Department of Medicine, Boston, MA (United States)

    2015-10-15

    To assess the severity of lung disease in cystic fibrosis (CF), scoring systems based on chest radiographs (CXRs), CT and MRI have been used extensively, although primarily in research settings rather than for clinical purposes. It has recently been shown that those based on CXRs (primarily the Brasfield and Wisconsin systems) are as sensitive and valid as those based on CT. The reproducibility and correlation of both systems to pulmonary function tests (PFTs) were recently investigated and were found to be statistically identical. However, the relative performance of these systems has not been specifically assessed in children younger than 5 years old with mild lung disease, a critical age range in which PFTs is rarely performed. To investigate and compare the performance of the Brasfield and Wisconsin systems in children 0-5 years old with predominantly mild lung disease. Fifty-five patients 0-5 years old with 105 CXRs were included in the study. Given that the goal was to compare system performance in mild disease, only the first two CXRs from each patient were included (all but five patients had two images). When only one image was available in the target age range, it only was included. Agreement between the Brasfield and Wisconsin systems was assessed using a 2X2 contingency table assuming binary classification of CF lung disease using CXR scoring systems (mild vs. non-mild). In the absence of PFTs or another external gold standard for comparison, the Wisconsin system was used as an arbitrary gold standard against which the Brasfield was compared. Correlation between the two systems was assessed via a concordance correlation coefficient (CCC) for repeated measures. Scores were rated as mild or non-mild based on published numerical cutoffs for each system. The systems agreed on 89/105 (85%) and disagreed on 16/105 (15%) of the CXRs. Agreement between the two systems was statistically significant (P < 0.001). Relative sensitivity and specificity of the

  12. Contemporary earthen architecture in the northern temperate climate

    DEFF Research Database (Denmark)

    Vestergaard, Inge; Eybye, Birgitte Tanderup

    2017-01-01

    houses designed using passive strategies and renewable materials have increased. Often the earth material, with its low environmental impact, is involved in the construction process. Building qualities include both pleasant living spaces and comfort in terms of better indoor climate. During the last few...... years new developments towards industrialized earthen building components can be seen. Hence the research question is: how can earth as a building material contribute to future Danish architecture? The results point out possible future developments in earthen architecture in Denmark. The methodologies...... and studying the applied materials and techniques....

  13. Analysis of water-level fluctuations in Wisconsin wells

    Science.gov (United States)

    Patterson, G.L.; Zaporozec, A.

    1987-01-01

    More than 60 percent of the residents of Wisconsin use ground water as their primary water source. Water supplies presently are abundant, but ground-water levels continually fluctuate in response to natural factors and human-related stresses. A better understanding of the magnitude, duration, and frequency of past fluctuations, and the factors controlling these fluctuations may help anticipate future changes in ground-water levels.

  14. Architectural constraints in IEC 61508: Do they have the intended effect?

    International Nuclear Information System (INIS)

    Lundteigen, Mary Ann; Rausand, Marvin

    2009-01-01

    The standards IEC 61508 and IEC 61511 employ architectural constraints to avoid that quantitative assessments alone are used to determine the hardware layout of safety instrumented systems (SIS). This article discusses the role of the architectural constraints, and particularly the safe failure fraction (SFF) as a design parameter to determine the hardware fault tolerance (HFT) and the redundancy level for SIS. The discussion is based on examples from the offshore oil and gas industry, but should be relevant for all applications of SIS. The article concludes that architectural constraints may be required to compensate for systematic failures, but the architectural constraints should not be determined based on the SFF. The SFF is considered to be an unnecessary concept

  15. Surface-water quality, Oneida Reservation and vicinity, Wisconsin, 1997-98

    Science.gov (United States)

    Schmidt, Morgan A.; Scudder, Barbara C.; Richards, Kevin D.

    2000-01-01

    Streamwater samples were collected at 19 sites in the vicinity of the Oneida Tribe of Indians of Wisconsin Reservation. Samples were collected during 5 sampling periods in 1997-98. Field measurements were made and samples were analyzed for nutrients, suspended sediment, major ions, and pesticides.

  16. On Farmers’ Ground: Wisconsin Dairy Farm Nutrient Management Survey Questionnaire

    Science.gov (United States)

    This questionnaire was used during quarterly, face-to-face interviews with the fifty-four Wisconsin dairy farmers who participated in the ‘On Farmers’ Ground’ nutrient management research project. It was designed to systematically and consistently compile information on herd size and composition, l...

  17. Cultural Identity of the Industrial Heritage in Gdansk

    Science.gov (United States)

    Szymański, Tomasz

    2017-10-01

    Since its inception, urbanized area passes a number of changes, caused by demands of its inhabitants. Industrial heritage, including historic architecture at the brownfields, that’s more and more present in the centres of our cities, is one of the most important components of the identity. The development of civilization causes the phenomenon of spatial and functional transformations. Revitalization of the areas recently occupied by the industry, provides a unique opportunity to rediscover their values. Increasingly, however, it uses the terms “wasteland” or “brownfields”. Land use by industry is associated only with its “predatory” use, destruction, devastation. However, we can venture to say, that the existing industrial use of the land, “civilized” them. Current developments have restored a public access to the “new” urban space. At these areas preserved quite a lot valuable architectural objects. That can be seen, unfortunately, tend to forget the fact of complexity, multithreaded value areas and facilities. Analyzed causes of the risks, ways to prevent adverse transformations, methods of developing action plans to re-create the industrial architecture - are still discussed. Industrial heritage, particularly architecture, is one of the important components of the material culture that specify identity of the city of Gdansk. It provides with no doubt about its distinctiveness and originality in relation to other cities and regions. Revitalization projects are at the same time the most effective way to protect and preserve the cultural identity of the brownfield facilities. Examples of such transformations are most relevant to Gdansk and also beginning to be more and more visible. Areas of the main activities of revitalization in Gdansk, are the area of the former Imperial Shipyard and the Ołowianka Island are still and only the beginning of the necessary changes. Old industrial plants and technical facilities should be subject of the

  18. Plasma ion implantation technology for broad industrial application

    International Nuclear Information System (INIS)

    Deb, D.; Siambis, J.; Symons, R.

    1994-01-01

    The recently invented Plasma Ion Implantation (PII) process (1987) [J. R. Conrad, U.S. Patent No. 764394 (August 16, 1988)] is currently under intense industrial engineering investigation and development. A critical component of PII for broad industrial utilization is the availability of an efficient modulator system that applies the high voltage pulse to the workpiece. A modulator technology assessment and selection is carried out. The requirements of the PII process favor the selection of a hard-tube modulator. The PII process favors the application of beam switch tube technology such as the Litton L-5012 and L-5097. These Litton tubes have already been selected by LANL and utilized in their pilot engineering demonstration experiment with GM and the University of Wisconsin. The performance, physical operation, and potential enhancements of the Litton beam switch tubes L-5012 and L-5097 will be discussed in connection with the requirements of the emerging plasma ion implantation industrial modulator technology

  19. Oneida Tribe of Indians of Wisconsin Energy Optimization Model

    Energy Technology Data Exchange (ETDEWEB)

    Troge, Michael [Little Bear Development Center, Oneida, WI (United States)

    2014-12-01

    Oneida Nation is located in Northeast Wisconsin. The reservation is approximately 96 square miles (8 miles x 12 miles), or 65,000 acres. The greater Green Bay area is east and adjacent to the reservation. A county line roughly splits the reservation in half; the west half is in Outagamie County and the east half is in Brown County. Land use is predominantly agriculture on the west 2/3 and suburban on the east 1/3 of the reservation. Nearly 5,000 tribally enrolled members live in the reservation with a total population of about 21,000. Tribal ownership is scattered across the reservation and is about 23,000 acres. Currently, the Oneida Tribe of Indians of Wisconsin (OTIW) community members and facilities receive the vast majority of electrical and natural gas services from two of the largest investor-owned utilities in the state, WE Energies and Wisconsin Public Service. All urban and suburban buildings have access to natural gas. About 15% of the population and five Tribal facilities are in rural locations and therefore use propane as a primary heating fuel. Wood and oil are also used as primary or supplemental heat sources for a small percent of the population. Very few renewable energy systems, used to generate electricity and heat, have been installed on the Oneida Reservation. This project was an effort to develop a reasonable renewable energy portfolio that will help Oneida to provide a leadership role in developing a clean energy economy. The Energy Optimization Model (EOM) is an exploration of energy opportunities available to the Tribe and it is intended to provide a decision framework to allow the Tribe to make the wisest choices in energy investment with an organizational desire to establish a renewable portfolio standard (RPS).

  20. Determination of resilient modulus values for typical plastic soils in Wisconsin.

    Science.gov (United States)

    2011-09-01

    "The objectives of this research are to establish a resilient modulus test results database and to develop : correlations for estimating the resilient modulus of Wisconsin fine-grained soils from basic soil properties. A : laboratory testing program ...

  1. Remedial Investigation Badger Army Ammunition Plant, Baraboo, Wisconsin. Volume 2. Appendices D.2 Through F

    Science.gov (United States)

    1991-01-01

    FILES FOR COMPOUNDS OF POTENTIAL CONCERN Vol. 7 APPENDIX 0 - HUMAN HEALTH RISK CALCULATIONS Vol. 7 APPENDIX P - INVENTORY OF SITE SPECIES Vol. 7...Driing Mud 0" 0 3 am 01 99 5 .Annula space seal:- GnmuldBsuryoni 0 33 Lbs/gal mud weight ... Benuar-siid shiny 3 33 16. Driling addives used 13 yesLbs...CONSTRUCTION REPORT / 5 WISCONSIN STATE BOARD OF HEALTH WELL DRILLING DIVISION JUL 11 |W Note: Section 32 of the Wisconsin Well Drilling Sanitary Code

  2. Biblioteca y Centro de Estudios de la Universidad de Wisconsin - Kenosha - . Wisconsin – (EE.UU.

    Directory of Open Access Journals (Sweden)

    Hellmuth, George

    1978-12-01

    Full Text Available Continuing the line established by these same architects in previous University designs, the Library and Study Hall of the University of Wisconsin is another attempt at creating an exciting atmosphere, particularly conducive to the development of university life. It is to be noted, in this case, the arrangement of the library and study areas around a central common open space, sort of an inner courtyard used as a relaxation and sitting área, where all traffic corridors and promenades from the adjacent faculties come to meet, thus becoming the main reference point for the entire campus. The library with a current capacity for 245,000 volumes and 1,400 reading stalls is designed so it can be eventually enlarged permitting to almost double its book capacity and increasing the reading stalls to more than 2,000.

    Continuando la línea marcada por estos mismos arquitectos en anteriores proyectos de universidades, la biblioteca y el centro de estudios de la Universidad de Wisconsin procura definir atractivos espacios para el desarrollo de la vida universitaria. En este caso destaca la organización de los servicios de biblioteca y estudio en torno a un espacio comunitario central, a modo de plaza interior, destinado a sala de estar y recreo, y en donde confluyen las circulaciones que provienen de los locales adyacentes, convirtiéndolo en el principal punto de referencia del campus universitario. La biblioteca, que actualmente tiene capacidad para 245.000 volúmenes y 1.400 lectores, ha previsto una ampliación que le permitirá casi doblar el número de volúmenes y proporcionar espacio para más de 2.000 lectores.

  3. From service-oriented architecture to service-oriented enterprise

    NARCIS (Netherlands)

    van Sinderen, Marten J.; Cordeiro, J.; Ivanov, I.; Shishkov, Boris

    2009-01-01

    Service-Oriented Architecture (SOA) was originally motivated by enterprise demands for better business-technology alignment and higher flexibility and reuse. SOA evolved from an initial set of ideas and principles to Web services (WS) standards now widely accepted by industry. The next phase of SOA

  4. Improving Outreach and Surveillance Efforts Following a Large-Scale Carbon Monoxide Poisoning in Wisconsin.

    Science.gov (United States)

    Creswell, Paul D; Vogt, Christy M; Wozniak, Ryan J; Camponeschi, Jenny; Werner, Mark A; Meiman, Jonathan G

    In December 2014, the largest carbon monoxide (CO) poisoning in Wisconsin's history occurred at an ice arena. Following this event, the Wisconsin Environmental Public Health Tracking (WI EPHT) Program sought to improve outreach and surveillance efforts. WI EPHT designed and distributed educational materials on CO poisoning prevention and surveyed stakeholders to gauge the effectiveness of outreach efforts. To enhance surveillance, WI EPHT utilized data from the Wisconsin Poison Center (WPC) to generate real-time alerts of anomalous numbers of CO-related calls. WI EPHT found that 42% of stakeholders reviewed the outreach materials, and 1 ice arena had installed a CO detector as a result. CO alerts were developed using WPC data and are now routinely used in statewide public health surveillance. WI EPHT staff improved CO poisoning prevention outreach and saw a positive response among stakeholders. This work demonstrates ways that health agencies can improve outreach and surveillance for CO poisoning. Improvements in these areas can bolster public health response and may prevent CO-related illness and injury.

  5. National Uranium Resource Evaluation: Iron River Quadrangle, Michigan and Wisconsin

    Energy Technology Data Exchange (ETDEWEB)

    Frishman, D

    1982-09-01

    No area within the Iron River 1/sup 0/ x 2/sup 0/ Quadrangle, Michigan and Wisconsin, appears to be favorable for the existence of a minimum of 100 tons of U/sub 3/O/sub 8/ at a grade of 0.01 percent or better.

  6. Information management architecture for an integrated computing environment for the Environmental Restoration Program. Environmental Restoration Program, Volume 3, Interim technical architecture

    International Nuclear Information System (INIS)

    1994-09-01

    This third volume of the Information Management Architecture for an Integrated Computing Environment for the Environmental Restoration Program--the Interim Technical Architecture (TA) (referred to throughout the remainder of this document as the ER TA)--represents a key milestone in establishing a coordinated information management environment in which information initiatives can be pursued with the confidence that redundancy and inconsistencies will be held to a minimum. This architecture is intended to be used as a reference by anyone whose responsibilities include the acquisition or development of information technology for use by the ER Program. The interim ER TA provides technical guidance at three levels. At the highest level, the technical architecture provides an overall computing philosophy or direction. At this level, the guidance does not address specific technologies or products but addresses more general concepts, such as the use of open systems, modular architectures, graphical user interfaces, and architecture-based development. At the next level, the technical architecture provides specific information technology recommendations regarding a wide variety of specific technologies. These technologies include computing hardware, operating systems, communications software, database management software, application development software, and personal productivity software, among others. These recommendations range from the adoption of specific industry or Martin Marietta Energy Systems, Inc. (Energy Systems) standards to the specification of individual products. At the third level, the architecture provides guidance regarding implementation strategies for the recommended technologies that can be applied to individual projects and to the ER Program as a whole

  7. Seasonal field metabolic rates of American martens in Wisconsin

    Science.gov (United States)

    Jonathan H. Gilbert; Patrick A Zollner; Adam K. Green; John L. Wright

    2009-01-01

    We report on FMR of free-living American martens (Martes americana) in autumn and winter in northern Wisconsin. Mean body mass was significantly higher in males (1099 ± 43 [S.E.] g) than females (737 ± 28 g), with no significant difference by season. Daily mass change rates of martens did not differ from zero, and mass change rate...

  8. Disruptive Logic Architectures and Technologies From Device to System Level

    CERN Document Server

    Gaillardon, Pierre-Emmanuel; Clermidy, Fabien

    2012-01-01

    This book discusses the opportunities offered by disruptive technologies to overcome the economical and physical limits currently faced by the electronics industry. It provides a new methodology for the fast evaluation of an emerging technology from an architectural perspective and discusses the implications from simple circuits to complex architectures. Several technologies are discussed, ranging from 3-D integration of devices (Phase Change Memories, Monolithic 3-D, Vertical NanoWires-based transistors) to dense 2-D arrangements (Double-Gate Carbon Nanotubes, Sublithographic Nanowires, Lithographic Crossbar arrangements). Novel architectural organizations, as well as the associated tools, are presented in order to explore this freshly opened design space. Describes a novel architectural organization for future reconfigurable systems; Includes a complete benchmarking toolflow for emerging technologies; Generalizes the description of reconfigurable circuits in terms of hierarchical levels; Assesses disruptive...

  9. Software architecture and engineering for patient records: current and future.

    Science.gov (United States)

    Weng, Chunhua; Levine, Betty A; Mun, Seong K

    2009-05-01

    During the "The National Forum on the Future of the Defense Health Information System," a track focusing on "Systems Architecture and Software Engineering" included eight presenters. These presenters identified three key areas of interest in this field, which include the need for open enterprise architecture and a federated database design, net centrality based on service-oriented architecture, and the need for focus on software usability and reusability. The eight panelists provided recommendations related to the suitability of service-oriented architecture and the enabling technologies of grid computing and Web 2.0 for building health services research centers and federated data warehouses to facilitate large-scale collaborative health care and research. Finally, they discussed the need to leverage industry best practices for software engineering to facilitate rapid software development, testing, and deployment.

  10. 75 FR 22589 - Preliminary Listing of an Additional Water to Wisconsin's 2008 List of Waters Under Section 303(d...

    Science.gov (United States)

    2010-04-29

    ... Wisconsin's 2008 List of Waters Under Section 303(d) of the Clean Water Act AGENCY: Environmental Protection... 303(d)(2) requires that States submit and EPA approve or disapprove lists of waters for which existing... approved Wisconsin's listing of waters, associated pollutants, and associated priority rankings. EPA...

  11. Trends and Opportunities of BIM-GIS Integration in the Architecture, Engineering and Construction Industry: A Review from a Spatio-Temporal Statistical Perspective

    Directory of Open Access Journals (Sweden)

    Yongze Song

    2017-12-01

    Full Text Available The integration of building information modelling (BIM and geographic information system (GIS in construction management is a new and fast developing trend in recent years, from research to industrial practice. BIM has advantages on rich geometric and semantic information through the building life cycle, while GIS is a broad field covering geovisualization-based decision making and geospatial modelling. However, most current studies of BIM-GIS integration focus on the integration techniques but lack theories and methods for further data analysis and mathematic modelling. This paper reviews the applications and discusses future trends of BIM-GIS integration in the architecture, engineering and construction (AEC industry based on the studies of 96 high-quality research articles from a spatio-temporal statistical perspective. The analysis of these applications helps reveal the evolution progress of BIM-GIS integration. Results show that the utilization of BIM-GIS integration in the AEC industry requires systematic theories beyond integration technologies and deep applications of mathematical modeling methods, including spatio-temporal statistical modeling in GIS and 4D/nD BIM simulation and management. Opportunities of BIM-GIS integration are outlined as three hypotheses in the AEC industry for future research on the in-depth integration of BIM and GIS. BIM-GIS integration hypotheses enable more comprehensive applications through the life cycle of AEC projects.

  12. Technical architecture of ONC-approved plans for statewide health information exchange.

    Science.gov (United States)

    Barrows, Randolph C; Ezzard, John

    2011-01-01

    ONC-approved state plans for HIE were reviewed for descriptions and depictions of statewide HIE technical architecture. Review was complicated by non-standard organizational elements and technical terminology across state plans. Findings were mapped to industry standard, referenced, and defined HIE architecture descriptions and characteristics. Results are preliminary due to the initial subset of ONC-approved plans available, the rapid pace of new ONC-plan approvals, and continuing advancements in standards and technology of HIE, etc. Review of 28 state plans shows virtually all include a direct messaging component, but for participating entities at state-specific levels of granularity (RHIO, enterprise, organization/provider). About ½ of reviewed plans describe a federated architecture, and ¼ of plans utilize a single-vendor "hybrid-federated" architecture. About 1/3 of states plan to leverage new federal and open exchange technologies (DIRECT, CONNECT, etc.). Only one plan describes a centralized architecture for statewide HIE, but others combine central and federated architectural approaches.

  13. Parametric Approach in Designing Large-Scale Urban Architectural Objects

    Directory of Open Access Journals (Sweden)

    Arne Riekstiņš

    2011-04-01

    Full Text Available When all the disciplines of various science fields converge and develop, new approaches to contemporary architecture arise. The author looks towards approaching digital architecture from parametric viewpoint, revealing its generative capacity, originating from the fields of aeronautical, naval, automobile and product-design industries. The author also goes explicitly through his design cycle workflow for testing the latest methodologies in architectural design. The design process steps involved: extrapolating valuable statistical data about the site into three-dimensional diagrams, defining certain materiality of what is being produced, ways of presenting structural skin and structure simultaneously, contacting the object with the ground, interior program definition of the building with floors and possible spaces, logic of fabrication, CNC milling of the proto-type. The author’s developed tool that is reviewed in this article features enormous performative capacity and is applicable to various architectural design scales.Article in English

  14. TEACHING DESIGN AT THE LIMITS OF ARCHITECTURE

    Directory of Open Access Journals (Sweden)

    Nikos A. Salingaros

    2010-07-01

    Full Text Available Pre-industrial architects inherently knew the effectual dimension of design through its materiality, detail, and form. Until now, the intellectual dichotomy of human thinking held that mind and body were separate entities, drawing a distinction between reasoned thought and feeling. The early Greek philosophers distinguished between these two realms. Theories on beauty, the human aesthetic impulse, and design were divided along the objective and subjective lines for centuries. In more current architectural terms, the objective dimension of industry gave structure and perceived virtue to the modernist paradigm, while at the same time clearing the way (tabula rasa for the rampant subjectivity we now see in the idiosyncratic expressions of so many contemporary architects. By revealing the relationship between our physical and mental processes, neuroscience re-situates the debate on physical reality well outside the intellectual enterprise of aesthetically driven design. Clear measures can now be evidenced, documented, and applied to establish a new, more effective, and humanly engaging way to build. This new architecture draws upon those mechanisms of neuro-connectivity that help us to feel safe and secure.   From this knowledge we have developed a new model for building/rebuilding the world, called Intelligence-Based Design. Intelligence-Based Design is the purposeful manipulation of the built environment to engage humans in an essential manner through complex organized information. Intelligence-Based Theory evidences the direct neurological evaluations of surface, structure, pattern, texture, and form, etc., and maintains that our sense of well being is established through positive neuro-engagement with the physical world at the deepest level common to all people, i.e. “Innate Intelligence.” This paper describes a senior architectural design studio taught using the precepts of Intelligence-Based Design. We describe our methodology, and the

  15. Web Service Architecture Framework for Embedded Devices

    Science.gov (United States)

    Yanzick, Paul David

    2009-01-01

    The use of Service Oriented Architectures, namely web services, has become a widely adopted method for transfer of data between systems across the Internet as well as the Enterprise. Adopting a similar approach to embedded devices is also starting to emerge as personal devices and sensor networks are becoming more common in the industry. This…

  16. Microgrids architectures and control

    CERN Document Server

    Hatziargyriou, Nikos

    2014-01-01

    Microgrids are the most innovative area in the electric power industry today. Future microgrids could exist as energy-balanced cells within existing power distribution grids or stand-alone power networks within small communities. A definitive presentation on all aspects of microgrids, this text examines the operation of microgrids - their control concepts and advanced architectures including multi-microgrids. It takes a logical approach to overview the purpose and the technical aspects of microgrids, discussing the social, economic and environmental benefits to power system operation. The bo

  17. Energy and architecture. [Denmark]; Energi + arkitektur

    Energy Technology Data Exchange (ETDEWEB)

    Lehrskov, H. [Ingenioerhoejskolen i Aarhus, Aarhus (Denmark); Oehlenschlaeger, R. [AplusB, Aarhus (Denmark); Kappel, K. [Solar City Copenhagen, Copenhagen (Denmark); Kleis, B. [Arkitekturformidling.dk, Vanloese (Denmark); Klint, J. [Kuben Management, Aarhus (Denmark); Vejsig Pedersen, P. [Cenergia, Herlev (Denmark)

    2011-07-01

    The book presents the best examples of Danish energy-oriented architecture with a focus on architectural and energy measures in the integrated design process, resulting in architectural quality. The book consists of two parts and consists first of an introduction to the challenges and tools within low-energy buildings, and then a catalog of a wide range of building projects in the categories of housing, business, education, institutions and sports. The book contains examples of new buildings that as a minimum meet the requirements of the building codes LE1, BR08. The book also contains suggestions for renovation projects that meet LE2 BR08, as the energy optimization of the existing building stock is an imminent task with great constructional and aesthetic challenges. The selected projects are designed and built in the period 2009 to 2011 and include both everyday architecture, created under highly competitive economic environment, as more exclusive development projects. The objectives of the projects are often higher than required by the building code, and in many projects measurements were made to find out what works. These examples show that the stricter energy requirements can serve as inspiration for a holistic architecture and contribute to a paradigm shift in the cooperation process between the project parties. But it is also clear that it requires a focused commitment of all players in the construction industry - clients, consultants, contractors and building product manufacturers - to reduce energy consumption significantly. (LN)

  18. Beech Range Extension and Vegetation History: Pollen Stratigraphy of Two Wisconsin Lakes.

    Science.gov (United States)

    Webb, Sara L

    1987-12-01

    The pollen stratigraphy of two small lakes in eastern Wisconsin (Radtke Lake, Washington county, and Gass Lake, Manitowoc County) records the Holocene (past 10 000 yr) spread of beech (Fagus grandifolia: Fagaceae). Radiocarbon dates were obtained for the oldest stratigraphic levels at which beech pollen appeared consistently in amounts > 0.5% of terrestrial pollen. A spatially continuous pattern of beech expansion from the north was ruled out, because beech trees grew in Wisconsin by 6000 BP, 2000 yr before adjacent populations were established to the north. Alternative geographic patterns of speed (from the south or east) were spatially discontinuous, requiring seed dispersal distances of perhaps 25-130 km. That beechnuts could be dispersed across such distances suggests (1) the involvement of Blue Jays, Passenger Pigeons, or other vertebrates, and (2) a capacity for reaching climatically controlled range limits, given sufficient time despite such discontinuities in habitat. A lag 1000-2000 yr between the establishment of source populations in Michigan and Indiana and the appearance of beech in Wisconsin suggests that low-probability dispersal events were involved and that dispersal constraints limited the range of beech during this time, although climatic and edaphic explanations for the lag cannot be ruled out. Pollen data from the two sites reveal other features of vegetation history in eastern Wisconsin: an open Picea-Fraxinus woodland prior to 11 000 BP; sequence of Picea, Abies, Betula, and then Pinus forests between 11 000 and 7500 BP; the establishment of a coniferous/deciduous forest ecotone ("tension zone") ° 7000 BP in this region; and the presence of Quercus-dominanted deciduous forests from 7000 BP until 110 BP (time of Euro-American settlement), a period punctuated by a gradual decrease in Ulmus populations (° 4500 and 5700 BP at the two sites) and by an increase in mesophytic tree abundance at the expense of Quercus after 3500 BP. © 1987 by the

  19. Designing network on-chip architectures in the nanoscale era

    CERN Document Server

    Flich, Jose

    2010-01-01

    Going beyond isolated research ideas and design experiences, Designing Network On-Chip Architectures in the Nanoscale Era covers the foundations and design methods of network on-chip (NoC) technology. The contributors draw on their own lessons learned to provide strong practical guidance on various design issues.Exploring the design process of the network, the first part of the book focuses on basic aspects of switch architecture and design, topology selection, and routing implementation. In the second part, contributors discuss their experiences in the industry, offering a roadmap to recent p

  20. Industrial Cloud: Toward Inter-enterprise Integration

    Science.gov (United States)

    Wlodarczyk, Tomasz Wiktor; Rong, Chunming; Thorsen, Kari Anne Haaland

    Industrial cloud is introduced as a new inter-enterprise integration concept in cloud computing. The characteristics of an industrial cloud are given by its definition and architecture and compared with other general cloud concepts. The concept is then demonstrated by a practical use case, based on Integrated Operations (IO) in the Norwegian Continental Shelf (NCS), showing how industrial digital information integration platform gives competitive advantage to the companies involved. Further research and development challenges are also discussed.

  1. Effects of consumption-oriented versus trophy-oriented fisheries on Muskellunge population size structure in northern Wisconsin

    Science.gov (United States)

    Faust, Matthew D.; Hansen, Michael J.

    2016-01-01

    To determine whether a consumption-oriented fishery was compatible with a trophy-oriented fishery for Muskellunge Esox masquinongy, we modeled effects of a spearing fishery and recreational angling fishery on population size structure (i.e., numbers of fish ≥ 102, 114, and 127 cm) in northern Wisconsin. An individual-based simulation model was used to quantify the effect of harvest mortality at currently observed levels of recreational angling and tribal spearing fishery exploitation, along with simulated increases in exploitation, for three typical growth potentials (i.e., low, moderate, and high) of Muskellunge in northern Wisconsin across a variety of minimum length limits (i.e., 71, 102, 114, and 127 cm). Populations with moderate to high growth potential and minimum length limits ≥ 114 cm were predicted to have lower declines in numbers of trophy Muskellunge when subjected to angling-only and mixed fisheries at observed and increased levels of exploitation, which suggested that fisheries with disparate motivations may be able to coexist under certain conditions such as restrictive length limits and low levels of exploitation. However, for most Muskellunge populations in northern Wisconsin regulated by a 102-cm minimum length limit, both angling and spearing fisheries may reduce numbers of trophy Muskellunge as larger declines were predicted across all growth potentials. Our results may be useful if Muskellunge management options in northern Wisconsin are re-examined in the future.

  2. A comparison of case volumes among urologic surgeons identified on an industry-sponsored website to an all provider peer group.

    Science.gov (United States)

    See, William A; Jacobson, Kenneth; Derus, Sue; Langenstroer, Peter

    2014-11-01

    Industry-sponsored websites for robotic surgery direct to surgeons listed as performing specific robotic surgical procedures. The purpose of this study was to compare average annual, surgeon-specific, case volumes for those procedures for which they were listed as performing on the commercial website with the volumes of all providers performing these same procedures across a defined geographic region. A list of providers within the state of Wisconsin cited as performing specific urologic procedures was obtained through the Intuitive Surgical website 〈http://www.davincisurgery.com/da-vinci-urology/〉. Surgeon-specific annual case volumes from 2009 to 2013 for these same cases were obtained for all Wisconsin providers through DataBay Resources (Warrendale, PA) based on International classification of diseases-9 codes. Procedural activity was rank ordered, and surgeons were placed in "volume deciles" derived from the total annual number of cases performed by all surgeons. The distribution of commercially listed surgeon volumes, both 5-year average and most recent year, was compared with the average and 2013 volumes of all surgeons performing a specific procedure. A total of 35 individual urologic surgeons listed as performing robotic surgery in Wisconsin were identified through a "search" using the Intuitive Surgical website. Specific procedure analysis returned 5, 12, 9, and 15 surgeon names for cystectomy, partial nephrectomy, radical nephrectomy, and prostatectomy, respectively. This compared with the total number of surgeons who had performed the listed procedure in Wisconsin at least 1 time during the prior 5 years of 123, 153, 242, and 165, respectively. When distributed by surgeon-volume deciles, surgeons listed on industry-sponsored sites varied widely in their respective volume decile. More than half of site-listed, procedure-specific surgeons fell below the fifth decile for surgeon volume. Data analysis based solely on 2013 case volumes had no effect on

  3. An interoperability architecture for the health information exchange in Rwanda

    CSIR Research Space (South Africa)

    Crichton, R

    2012-08-01

    Full Text Available Zulu-Natal and Council for Scientific and Industrial Research, Durban, South Africa 2 Jembi Health Systems, Cape Town and Durban, South Africa, 3 Medical Research Council, Cape Town, South Africa Abstract. Rwanda, one of the smallest and most densely populated... and the national rollout of an electronic medical record application[15]. The Rwanda Health Enterprise Architecture (RHEA) project, led by the Rwanda MoH and supported by a consortium of partners and donors has developed an architecture to contribute...

  4. Modular, Cost-Effective, Extensible Avionics Architecture for Secure, Mobile Communications

    Science.gov (United States)

    Ivancic, William D.

    2007-01-01

    Current onboard communication architectures are based upon an all-in-one communications management unit. This unit and associated radio systems has regularly been designed as a one-off, proprietary system. As such, it lacks flexibility and cannot adapt easily to new technology, new communication protocols, and new communication links. This paper describes the current avionics communication architecture and provides a historical perspective of the evolution of this system. A new onboard architecture is proposed that allows full use of commercial-off-the-shelf technologies to be integrated in a modular approach thereby enabling a flexible, cost-effective and fully deployable design that can take advantage of ongoing advances in the computer, cryptography, and telecommunications industries.

  5. Architectural slicing

    DEFF Research Database (Denmark)

    Christensen, Henrik Bærbak; Hansen, Klaus Marius

    2013-01-01

    Architectural prototyping is a widely used practice, con- cerned with taking architectural decisions through experiments with light- weight implementations. However, many architectural decisions are only taken when systems are already (partially) implemented. This is prob- lematic in the context...... of architectural prototyping since experiments with full systems are complex and expensive and thus architectural learn- ing is hindered. In this paper, we propose a novel technique for harvest- ing architectural prototypes from existing systems, \\architectural slic- ing", based on dynamic program slicing. Given...... a system and a slicing criterion, architectural slicing produces an architectural prototype that contain the elements in the architecture that are dependent on the ele- ments in the slicing criterion. Furthermore, we present an initial design and implementation of an architectural slicer for Java....

  6. The Advancing a Healthier Wisconsin Endowment: How a Health Care Conversion Foundation Is Transforming a Medical School.

    Science.gov (United States)

    Maurana, Cheryl A; Lucey, Paula A; Ahmed, Syed M; Kerschner, Joseph E; Bolton, G Allen; Raymond, John R

    2016-01-01

    Health care conversion foundations, such as the Advancing a Healthier Wisconsin Endowment (the endowment) at the Medical College of Wisconsin (MCW), result from the conversion of nonprofit health organizations to for-profit corporations. Over the past several decades, nearly 200 of these foundations have been created, and they have had a substantial impact on the field of health philanthropy. The MCW was a recipient of funds resulting from Blue Cross & Blue Shield United of Wisconsin's conversion from a nonprofit to a for-profit status in 1999. Established in 2004, the endowment has invested approximately $185 million in 337 research, education, and public and community health initiatives that benefit Wisconsin residents. However, the transformative potential of the health care conversion foundation has extended well beyond the opportunities provided through the endowment's financial resources. As the endowment celebrates its 10th anniversary, the authors describe the transformative nature of the endowment, as well as significant accomplishments and lessons learned, in the following areas: shared power, community partnerships, translational research, and integration of medicine and public health. It is the authors' hope that these lessons will be valuable to other medical schools and the communities they serve, as they invest in improving the health of their communities, irrespective of the funding source.

  7. Modularization of Industrial Service Processes

    DEFF Research Database (Denmark)

    Frandsen, Thomas; Hsuan, Juliana

    In this paper we examine how complex service processes can be dealt with through the lenses of modularization strategies. Through an illustrative case study of a manufacturer of industrial equipment for process industries we propose the use of the service modularity function to conceptualize...... and assess the service modularity of service offerings. The measured degree of modularity would allow us to sharpen our understanding of modularity in the context of industrial services, such as the role of standardization and component reuse on architecture flexibility. It would also provide a foundation...

  8. Universal discrete Fourier optics RF photonic integrated circuit architecture.

    Science.gov (United States)

    Hall, Trevor J; Hasan, Mehedi

    2016-04-04

    This paper describes a coherent electro-optic circuit architecture that generates a frequency comb consisting of N spatially separated orders using a generalised Mach-Zenhder interferometer (MZI) with its N × 1 combiner replaced by an optical N × N Discrete Fourier Transform (DFT). Advantage may be taken of the tight optical path-length control, component and circuit symmetries and emerging trimming algorithms offered by photonic integration in any platform that offers linear electro-optic phase modulation such as LiNbO3, silicon, III-V or hybrid technology. The circuit architecture subsumes all MZI-based RF photonic circuit architectures in the prior art given an appropriate choice of output port(s) and dimension N although the principal application envisaged is phase correlated subcarrier generation for all optical orthogonal frequency division multiplexing. A transfer matrix approach is used to model the operation of the architecture. The predictions of the model are validated by simulations performed using an industry standard software tool. Implementation is found to be practical.

  9. Assessing Future Ecosystem Services: a Case Study of the Northern Highlands Lake District, Wisconsin

    Directory of Open Access Journals (Sweden)

    Garry D. Peterson

    2003-12-01

    Full Text Available The Northern Highlands Lake District of Wisconsin is in transition from a sparsely settled region to a more densely populated one. Expected changes offer benefits to northern Wisconsin residents but also threaten to degrade the ecological services they rely on. Because the future of this region is uncertain, it is difficult to make decisions that will avoid potential risks and take advantage of potential opportunities. We adopt a scenario planning approach to cope with this problem of prediction. We use an ecological assessment framework developed by the Millennium Ecosystem Assessment to determine key social and ecological driving forces in the Northern Highlands Lake District. From these, we describe three alternative scenarios to the year 2025 in which the projected use of ecological services is substantially different. The work reported in this paper demonstrates how scenarios can be developed for a region and provides a starting point for a participatory discussion of alternative futures for northern Wisconsin. Although the future is unknowable, we hope that the assessment process begun in this paper will help the people of the Northern Highlands Lake District choose the future path of their region.

  10. SUSTAINABLE ARCHITECTURE : WHAT ARCHITECTURE STUDENTS THINK

    OpenAIRE

    SATWIKO, PRASASTO

    2013-01-01

    Sustainable architecture has become a hot issue lately as the impacts of climate change become more intense. Architecture educations have responded by integrating knowledge of sustainable design in their curriculum. However, in the real life, new buildings keep coming with designs that completely ignore sustainable principles. This paper discusses the results of two national competitions on sustainable architecture targeted for architecture students (conducted in 2012 and 2013). The results a...

  11. Architecture survey analysis by CSA initiative : volume I final report

    Science.gov (United States)

    1993-07-01

    Many organizations in industry and government, face challenges in information management similar to the Federal Aviation Administration (FAA). The objective of the Architecture Survey is to enable the FAA to build upon the experience and technical co...

  12. 76 FR 63852 - Proposed Establishment of the Wisconsin Ledge Viticultural Area

    Science.gov (United States)

    2011-10-14

    ..., University of Wisconsin Press, 1965, page 281). The western portion of the proposed boundary line extends... grapevine growth (``General Viticulture,'' by Albert J. Winkler, University of California Press, 1974, pages... River National Wildlife Refuges. Finally, the petition adds that Horicon Ledge Park, Ledge View County...

  13. Architecture

    OpenAIRE

    Clear, Nic

    2014-01-01

    When discussing science fiction’s relationship with architecture, the usual practice is to look at the architecture “in” science fiction—in particular, the architecture in SF films (see Kuhn 75-143) since the spaces of literary SF present obvious difficulties as they have to be imagined. In this essay, that relationship will be reversed: I will instead discuss science fiction “in” architecture, mapping out a number of architectural movements and projects that can be viewed explicitly as scien...

  14. Model-based security analysis of the German health card architecture.

    Science.gov (United States)

    Jürjens, J; Rumm, R

    2008-01-01

    Health-care information systems are particularly security-critical. In order to make these applications secure, the security analysis has to be an integral part of the system design and IT management process for such systems. This work presents the experiences and results from the security analysis of the system architecture of the German Health Card, by making use of an approach to model-based security engineering that is based on the UML extension UMLsec. The focus lies on the security mechanisms and security policies of the smart-card-based architecture which were analyzed using the UMLsec method and tools. Main results of the paper include a report on the employment of the UMLsec method in an industrial health information systems context as well as indications of its benefits and limitations. In particular, two potential security weaknesses were detected and countermeasures discussed. The results indicate that it can be feasible to apply a model-based security analysis using UMLsec to an industrial health information system like the German Health Card architecture, and that doing so can have concrete benefits (such as discovering potential weaknesses, and an increased confidence that no further vulnerabilities of the kind that were considered are present).

  15. Evaluation of nonpoint-source contamination, Wisconsin: water year 1999

    Science.gov (United States)

    Walker, John F.; Graczyk, D.J.; Corsi, Steven R.; Wierl, J.A.; Owens, D.W.

    2001-01-01

    The objective of the watershed-management evaluation monitoring program in Wisconsin is to evaluate the effectiveness of best-management practices (BMPs) for controlling nonpoint-source pollution in rural and urban watersheds. This progress report provides a summary of the data collected by the U.S Geological Survey for the program and a discussion of the results from several different detailed analyses conducted within this program.

  16. Integration of Structural Knowledge in Design Studio Project: Assessment Study of Curriculum In Architecture Course in University Of Malaya

    Directory of Open Access Journals (Sweden)

    Aniza Abdul Aziz

    2010-12-01

    Full Text Available Architectural education should advance in parallel with the industrial growth of building technology. Universities as producers of future architects have yet to develop curriculums for building technology to suit the growth of the building industry. This gap between education and industrial growth has been a topic of debate for many researchers who are concerned about architectural pedagogy. Architectural instruction further aggravated the problem whereby in most architectural schools worldwide, teaching is divided between the design studio, where the design projects are taught and lecture classes where the technical parts are taught. The latter should be integrated with design studio to enhance design levels. Students face difficulty integrating and applying the structural knowledge gained from structure classes into their design. One explanation for this deficiency is because the current architectural structure subject's content is borrowed from an engineering syllabus. This study will examine the course content, instruction styles and method of teaching structure subjects and will investigate the learning outcomes of design studio through students' performance and perception in integrating structural knowledge in their design projects. Respondents were students from Year 1 to Year 5 doing their Bachelor of Science in Architecture and Bachelor of Architecture degrees in University of Malaya. Semi-structured interviews were conducted with the design studio coordinators and structure lecturers. This study aims to find the ideal course content/method of teaching to facilitate more integration between structure and design studio.

  17. BASIC LAWS OF FORMATION OF INNOVATION HISTORICAL ARCHITECTURE AND TOWN PLANNING FACILITIES IN URBAN ENVIRONMENT

    Directory of Open Access Journals (Sweden)

    SMIRNOVA O. V.

    2016-06-01

    Full Text Available Abstract. Formulation of the problem. Innovative buildings and structures are architectural objects, the distinguishing feature of which is the presence of certain levels of their formation - material and functional (provided certain functional purpose object and its material embodiment, art-shaped (the presence of an individual artistic image structural and process (use of new technologies and fundamentally new design; communication and of environmental (harmonious integration of the object in the environment. Absence of analogues - a prerequisite for innovative buildings. Innovative architectural and urban objects created in the development of civilization. Innovations in design and construction of architectural and urban facilities - this is the final result of the creation (design and development (implementation of a fundamentally new or modified facility satisfies human needs. Purpose. Consider the historical features of formation of innovative architectural and urban facilities in the urban environment. The main objectives - to identify the main types of innovative historical objects and identify patterns of their formation. Conclusions. The main historical innovative architectural and urban facilities were buildings and structures formed during two periods of historical development: in the pre-industrial period and during the industrial revolution.

  18. Expanding color design methods for architecture and allied disciplines

    Science.gov (United States)

    Linton, Harold E.

    2002-06-01

    The color design processes of visual artists, architects, designers, and theoreticians included in this presentation reflect the practical role of color in architecture. What the color design professional brings to the architectural design team is an expertise and rich sensibility made up of a broad awareness and a finely tuned visual perception. This includes a knowledge of design and its history, expertise with industrial color materials and their methods of application, an awareness of design context and cultural identity, a background in physiology and psychology as it relates to human welfare, and an ability to problem-solve and respond creatively to design concepts with innovative ideas. The broadening of the definition of the colorists's role in architectural design provides architects, artists and designers with significant opportunities for continued professional and educational development.

  19. Modeling Architectural Patterns Using Architectural Primitives

    NARCIS (Netherlands)

    Zdun, Uwe; Avgeriou, Paris

    2005-01-01

    Architectural patterns are a key point in architectural documentation. Regrettably, there is poor support for modeling architectural patterns, because the pattern elements are not directly matched by elements in modeling languages, and, at the same time, patterns support an inherent variability that

  20. Ecologic Niche Modeling of Blastomyces dermatitidis in Wisconsin

    Science.gov (United States)

    Reed, Kurt D.; Meece, Jennifer K.; Archer, John R.; Peterson, A. Townsend

    2008-01-01

    Background Blastomycosis is a potentially fatal mycosis that is acquired by inhaling infectious spores of Blastomyces dermatitidis present in the environment. The ecology of this pathogen is poorly understood, in part because it has been extremely difficult to identify the niche(s) it occupies based on culture isolation of the organism from environmental samples. Methodology/Principal Findings We investigated the ecology of blastomycosis by performing maximum entropy modeling of exposure sites from 156 cases of human and canine blastomycosis to provide a regional-scale perspective of the geographic and ecologic distribution of B. dermatitidis in Wisconsin. Based on analysis with climatic, topographic, surface reflectance and other environmental variables, we predicted that ecologic conditions favorable for maintaining the fungus in nature occur predominantly within northern counties and counties along the western shoreline of Lake Michigan. Areas of highest predicted occurrence were often in proximity to waterways, especially in northcentral Wisconsin, where incidence of infection is highest. Ecologic conditions suitable for B. dermatitidis are present in urban and rural environments, and may differ at the extremes of distribution of the species in the state. Conclusions/Significance Our results provide a framework for a more informed search for specific environmental factors modulating B. dermatitidis occurrence and transmission and will be useful for improving public health awareness of relative exposure risks. PMID:18446224

  1. Integration of Sensors, Controllers and Instruments Using a Novel OPC Architecture.

    Science.gov (United States)

    González, Isaías; Calderón, Antonio José; Barragán, Antonio Javier; Andújar, José Manuel

    2017-06-27

    The interconnection between sensors, controllers and instruments through a communication network plays a vital role in the performance and effectiveness of a control system. Since its inception in the 90s, the Object Linking and Embedding for Process Control (OPC) protocol has provided open connectivity for monitoring and automation systems. It has been widely used in several environments such as industrial facilities, building and energy automation, engineering education and many others. This paper presents a novel OPC-based architecture to implement automation systems devoted to R&D and educational activities. The proposal is a novel conceptual framework, structured into four functional layers where the diverse components are categorized aiming to foster the systematic design and implementation of automation systems involving OPC communication. Due to the benefits of OPC, the proposed architecture provides features like open connectivity, reliability, scalability, and flexibility. Furthermore, four successful experimental applications of such an architecture, developed at the University of Extremadura (UEX), are reported. These cases are a proof of concept of the ability of this architecture to support interoperability for different domains. Namely, the automation of energy systems like a smart microgrid and photobioreactor facilities, the implementation of a network-accessible industrial laboratory and the development of an educational hardware-in-the-loop platform are described. All cases include a Programmable Logic Controller (PLC) to automate and control the plant behavior, which exchanges operative data (measurements and signals) with a multiplicity of sensors, instruments and supervisory systems under the structure of the novel OPC architecture. Finally, the main conclusions and open research directions are highlighted.

  2. Social Vulnerability Index (SoVI) for Wisconsin based on 2000 Census Block Groups

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This data depicts the social vulnerability of Wisconsin census block groups to environmental hazards. Data were culled primarily from the 2000 Decennial Census.

  3. CONTEMPORARY SLOVENIAN TIMBER ARCHITECTURE INTERNATIONAL RECOGNIZED

    Directory of Open Access Journals (Sweden)

    Manja Kitek Kuzman

    2014-12-01

    Full Text Available The book presents Slovenia' s contemporary timber architecture. Thanks to its abundant forests, Slovenia has preserved the tradition of wood construction. As much as 60% of its surface is covered by forests. Slovenia is also the third most forested country in Europe. The high share of forest-covered surface allows for a sustainable production of high-quality wood. In the past, wood was used primarily in the construction of farm buildings, but now timber architecture is used for everything from residences and office buildings to public buildings such as community centres and schools. Timber construction is becoming increasingly popular. Apart from larger companies taking this approach, a great number of wooden houses have sprung up, built either on personal initiative or with the support of carpenter workshops. Slovenian timber architecture has taken a new approach to environmental and energy-efficiency problems and received great international recognition. The book discusses over fifty projects built over a ten-year period, and includes descriptions, photographs, and plans. The projects include residential areas, administration, and office, as well as tourist, educational, and industrial buildings. Timber architecture is presented as an integral part of the Slovenian landscape. The monograph will be useful to designers and future experts in their planning of optimal timber buildings and will highlight the main benefits of using timber construction.

  4. Borreliosis in free-ranging black bears from Wisconsin.

    Science.gov (United States)

    Kazmierczak, J J; Amundson, T E; Burgess, E C

    1988-04-01

    Blood, kidney and tick samples were obtained from 18 hunter-killed black bears (Ursus americanus) from three sites in northern Wisconsin. A Borrelia sp., morphologically and antigenically similar to Borrelia burgdorferi, was isolated from the blood of two of the animals, and from the kidney of a third. Ixodes dammini and Dermacentor variabilis were found on the bears. This is the first report of borreliosis in the Ursidae, and of the primary vector of Lyme disease, I. dammini, from this host.

  5. Dairy sheep production research at the University of Wisconsin-Madison, USA - a review.

    Science.gov (United States)

    Thomas, David L; Berger, Yves M; McKusick, Brett C; Mikolayunas, Claire M

    2014-01-01

    Commercial milking of sheep is a new agricultural industry in the United States starting approximately 30 yr ago. The industry is still small, but it is growing. The majority of the sheep milk is used in the production of specialty cheeses. The United States is the major importer of sheep milk cheeses with 50 to 60% of annual world exports coming to the United States during the past 20 yr. Therefore, there is considerable growth potential for the industry in the United States. The only dairy sheep research flock in North America is located at the Spooner Agricultural Research Station of the University of Wisconsin-Madison. The research program started in 1993 and has been multifaceted; dealing with several areas important to commercial dairy sheep farmers. The East Friesian and Lacaune dairy breeds were compared and introduced to the industry through the research program. Both dairy breeds produced significantly more milk than traditional meat-wool breeds found in the U.S., but the two breeds differed in their production traits. East Friesian-cross ewes produced more lambs and slightly more milk than Lacaune-cross ewes whereas Lacaune-cross ewes produced milk with a higher percentage of fat and protein than East Friesian-cross ewes. Lactation physiology studies have shown that ewes with active corpora lutea have increased milk yields, oxytocin release during milking is required to obtain normal fat percentages in the milk, large udder cisterns of dairy ewes can allow for increased milking intervals, and short daylengths during late pregnancy results in increased milk yield. In the nutrition area, legume-grass pastures and forages with a higher percentage of legume will result in increased milk production. Grazing ewes respond to additional supplementation with increased milk yield, but it is important to match the supplement to the quality of the grazing. Ewes on high quality legume-grass pastures that are high in rumen degradable protein respond with increased

  6. Industrial cloud-based cyber-physical systems the IMC-AESOP approach

    CERN Document Server

    Bangemann, Thomas; Karnouskos, Stamatis; Delsing, Jerker; Stluka, Petr; Harrison, Robert; Jammes, Francois; Lastra, Jose

    2014-01-01

    This book presents cutting-edge emerging technologies and approaches in the areas of service-oriented architectures, intelligent devices, and cloud-based cyber-physical systems. It provides a clear view on their applicability to the management and automation of manufacturing and process industries. It offers a holistic view of future industrial cyber-physical systems and their industrial usage, and also depicts technologies and architectures as well as a migration approach and engineering tools based on these. By providing a careful balance between the theory and the practical aspects, this book has been authored by several experts from academia and industry, thereby offering a valuable understanding of the vision, the domain, the processes and the results of the research. It has several illustrations and tables to clearly exemplify the concepts and results examined in the text, and these are supported by four real-life case-studies. We are witnessing rapid advances in the industrial automation, mainly driven...

  7. Control system devices : architectures and supply channels overview.

    Energy Technology Data Exchange (ETDEWEB)

    Trent, Jason; Atkins, William Dee; Schwartz, Moses Daniel; Mulder, John C.

    2010-08-01

    This report describes a research project to examine the hardware used in automated control systems like those that control the electric grid. This report provides an overview of the vendors, architectures, and supply channels for a number of control system devices. The research itself represents an attempt to probe more deeply into the area of programmable logic controllers (PLCs) - the specialized digital computers that control individual processes within supervisory control and data acquisition (SCADA) systems. The report (1) provides an overview of control system networks and PLC architecture, (2) furnishes profiles for the top eight vendors in the PLC industry, (3) discusses the communications protocols used in different industries, and (4) analyzes the hardware used in several PLC devices. As part of the project, several PLCs were disassembled to identify constituent components. That information will direct the next step of the research, which will greatly increase our understanding of PLC security in both the hardware and software areas. Such an understanding is vital for discerning the potential national security impact of security flaws in these devices, as well as for developing proactive countermeasures.

  8. Energy Management in Industrial Plants

    Directory of Open Access Journals (Sweden)

    Dario Bruneo

    2012-09-01

    Full Text Available The Smart Grid vision imposes a new approach towards energy supply that is more affordable, reliable and sustainable. The core of this new vision is the use of advanced technology to monitor power system dynamics in real time and identify system in stability. In order to implement strategic vision for energy management, it is possible to identify three main areas of investigation such as smart generation, smart grid and smart customer. Focusing on the latter topic, in this paper we present an application specifically designed to monitor an industrial site with particular attention to power consumption. This solution is a real time analysis tool, able to produce useful results to have a strategic approach in the energy market and to provide statistic analysis useful for the future choices of the industrial company. The application is based on a three layers architecture. The technological layer uses a Wireless Sensor Network (WSN to acquire data from the electrical substations. The middleware layer faces the integration problems by processing the raw data. The application layer manages the data acquired from the sensors. This WSN based architecture represents an interesting example of a low cost and non-invasive monitoring application to keep the energy consumption of an industrial site under control. Some of the added value features of the proposed solution are the routing network protocol, selected in order to have an high availability of the WSN, and the use of the WhereX middleware, able to easily implement integration among the different architectural parts.

  9. Microgrid cyber security reference architecture.

    Energy Technology Data Exchange (ETDEWEB)

    Veitch, Cynthia K.; Henry, Jordan M.; Richardson, Bryan T.; Hart, Derek H.

    2013-07-01

    This document describes a microgrid cyber security reference architecture. First, we present a high-level concept of operations for a microgrid, including operational modes, necessary power actors, and the communication protocols typically employed. We then describe our motivation for designing a secure microgrid; in particular, we provide general network and industrial control system (ICS)-speci c vulnerabilities, a threat model, information assurance compliance concerns, and design criteria for a microgrid control system network. Our design approach addresses these concerns by segmenting the microgrid control system network into enclaves, grouping enclaves into functional domains, and describing actor communication using data exchange attributes. We describe cyber actors that can help mitigate potential vulnerabilities, in addition to performance bene ts and vulnerability mitigation that may be realized using this reference architecture. To illustrate our design approach, we present a notional a microgrid control system network implementation, including types of communica- tion occurring on that network, example data exchange attributes for actors in the network, an example of how the network can be segmented to create enclaves and functional domains, and how cyber actors can be used to enforce network segmentation and provide the neces- sary level of security. Finally, we describe areas of focus for the further development of the reference architecture.

  10. Archaeological Investigations at a Wisconsin Petroglyph Site

    Directory of Open Access Journals (Sweden)

    Jack Steinbring

    2014-01-01

    Full Text Available Preliminary test excavations at the Hensler Petroglyph Site in East Central Wisconsin, U.S.A. have disclosed the remains of aboriginal engravings below Aeolian sediments dated to ca. 15,000 years B.P. The stratified deposits lying adjacent to an engraved panel, containing 35 pecked images, have yielded animal-like cobbles, some covered with red ochre, apparently picked for some esoteric use. The site itself has unusual natural shapes in the rock formation, along with acoustical properties, lightning strikes, a magnetic anomaly, and geographic prominence. Collectively these factors are thought to have attracted the ancient rock artists to the site.

  11. Resilience Theory and Praxis: a Critical Framework for Architecture

    Directory of Open Access Journals (Sweden)

    Michelle Laboy

    2016-12-01

    Full Text Available The growing use of resilience as a goal of architectural practice presents a new challenge in architects’ responsibility to health, safety, welfare and poetic expression of human-building interaction. With roots in disaster response, resilience in the building industry emphasizes the preservation and rapid restoration of the physical environment’s normal function in the face of shocks and disturbances of limited duration. The focus on maintaining function, and/or rapidly returning to the status quo ante necessarily affords a narrow understanding of architecture and a limited view of the concept of resilience. While useful at certain scales of time and inquiry, this so-called engineering resilience approach is only one among many within the broad discourse across diverse disciplines such as psychology, economics, and ecology.  Drawing on the academic and professional literature of resilience outside the discipline, this paper explores the multiple competing frameworks represented, considers their influences and implications for architecture and the built environment at multiple scales, and examines the overlaps with existing discourse on change, architecture and time. The analysis of alternative concepts enables a critical perspective to move beyond the circumscribed, functionalist approach afforded by engineering resilience currently guiding architecture practice, towards a framework of social- ecological resilience that can fully embrace the richness of architecture, and results in a necessary and clear theoretical basis for the resilience of architecture over time in a climate of increasing uncertainty.

  12. Enterprise Architecture Modeling of Core Administrative Systems at KTH : A Modifiability Analysis

    OpenAIRE

    Rosell, Peter

    2012-01-01

    This project presents a case study of modifiability analysis on the Information Systems which are central to the core business processes of Royal Institution of Technology in Stockholm, Sweden by creating, updating and using models. The case study was limited to modifiability regarding only specified Information Systems. The method selected was Enterprise Architecture together with Enterprise Architecture Analysis research results and tools from the Industrial Information and Control Systems ...

  13. ETL as a Necessity for Business Architectures

    Directory of Open Access Journals (Sweden)

    Aurelian TITIRISCA

    2013-07-01

    Full Text Available Today, the new trend that companies are following is to digitalize all data they have in order to reduce costs with physical space and better handle data volume. The new era, the era of bundling data sources and huge volumes of data continues this decade also. In all industries, companies are starting to understand and appreciate the value of data, the value that these volumes of data can produce. Companies are collecting huge volumes of data but not always the actual solution for business intelligence (BI can handle these volumes. To obtain information, those volumes of data are analyzed with extract-transform-load (ETL software solutions. Companies, in the current economic context, are finding hard to invest in improvements of BI process including in ETL process. In this paper I will demonstrate why this kind of investment is necessary and also I will demonstrate that ETL process must be included in BI and big data architectures. In the following pages I will refer to business architectures as BI and big data architectures.

  14. Light Water Reactor Sustainability Program: Digital Architecture Project Plan

    Energy Technology Data Exchange (ETDEWEB)

    Thomas, Ken [Idaho National Lab. (INL), Idaho Falls, ID (United States)

    2014-09-01

    There are many technologies available to the nuclear power industry to improve efficiency in plant work activities. These range from new control room technologies to those for mobile field workers. They can make a positive impact on a wide range of performance objectives – increase in productivity, human error reduction, validation of results, accurate transfer of data, and elimination of repetitive tasks. It is expected that the industry will more and more turn to these technologies to achieve these operational efficiencies to lower costs. At the same time, this will help utilities manage a looming staffing problem as the inevitable retirement wave of the more seasoned workers affects both staffing levels and knowledge retention. A barrier to this wide-scale implementation of new technologies for operational efficiency is the lack of a comprehensive digital architecture that can support the real-time information exchanges needed to achieve the desired operational efficiencies. This project will define an advanced digital architecture that will accommodate the entire range of system, process, and plant worker activity to enable the highest degree of integration, thereby creating maximum efficiency and productivity. This pilot project will consider a range of open standards that are suitable for the various data and communication requirements of a seamless digital environment. It will map these standards into an overall architecture to support the II&C developments of this research program.

  15. Increasing educational disparities in premature adult mortality, Wisconsin, 1990-2000.

    Science.gov (United States)

    Reither, Eric N; Peppard, Paul E; Remington, Patrick L; Kindig, David A

    2006-10-01

    Public health agencies have identified the elimination of health disparities as a major policy objective. The primary objective of this study is to assess changes in the association between education and premature adult mortality in Wisconsin, 1990-2000. Wisconsin death records (numerators) and US Census data (denominators) were compiled to estimate mortality rates among adults (25-64 years) in 1990 and 2000. Information on the educational status, sex, racial identification, and age of subjects was gathered from these sources. The effect of education on mortality rate ratios in 1990 and 2000 was assessed while adjusting for age, sex, and racial identification. Education exhibited a graded effect on mortality rates, which declined most among college graduates from 1990 to 2000. The relative rate of mortality among persons with less than a high school education compared to persons with a college degree increased from 2.4 to 3.1 from 1990-2000-an increase of 29%. Mortality disparities also increased, although to a lesser extent, among other educational groups. Despite renewed calls for the elimination of health disparities, evidence suggests that educational disparities in mortality increased from 1990 to 2000.

  16. Surface-water hydrology and quality, and macroinvertebrate and smallmouth bass populations in four stream basins in southwestern Wisconsin, 1987-90

    Science.gov (United States)

    Graczyk, David J.; Lillie, Richard A.; Schlesser, Roger A.; Mason, John W.; Lyons, John D.; Kerr, Roger A.; Graczyk, David J.

    1993-01-01

    Data on streamflow, water quality, and macroinvertebrate and smallmouth bass (microptercus dolomieni) populations were collected from July 1987 through September 1990, in four streams in southwestern Wisconsin to determine the effect of surface-water hydrology and quality on populations of macroinvertebrates and smallmouth bass. The study was a joint project of the U.S. Geological Survey and the Wisconsin Department of Natural Resources.

  17. The Industry 4.0 Journey: Start the Learning Journey with the Reference Architecture Model Industry 4.0

    DEFF Research Database (Denmark)

    Nardello, Marco; Møller, Charles; Gøtze, John

    2017-01-01

    The wave of the fourth industrial revolution (Industry 4.0) is breaking on manufacturing companies. In manufacturing, one of the buzzwords of the moment is "Smart production". Smart production involves manufacturing equipment with many sensors that can generate and transmit large amounts of data....... Model Industry 4.0 (RAMI4.0) standard for Smart production. The instantiation contributed to organizational learning in the laboratory by collecting and sharing up-to-date information concerning manufacturing equipment....

  18. Evaluation of wood species and preservatives for Wisconsin transportation sign posts : [research brief].

    Science.gov (United States)

    2013-12-01

    The Wisconsin Department of Transportation (WisDOT) administers approximately 11,800 miles of state highways. It uses preservative-treated wood posts for much of the signage along these highways because wood is relatively inexpensive, easy to install...

  19. Architectural prototyping

    DEFF Research Database (Denmark)

    Bardram, Jakob Eyvind; Christensen, Henrik Bærbak; Hansen, Klaus Marius

    2004-01-01

    A major part of software architecture design is learning how specific architectural designs balance the concerns of stakeholders. We explore the notion of "architectural prototypes", correspondingly architectural prototyping, as a means of using executable prototypes to investigate stakeholders...

  20. Space Industry Commercialization: A Systems Engineering Evaluation of Alternatives

    Science.gov (United States)

    Dinally, Jihan

    The Constellation Program cancellation reversed the government and commercial space industry's roles and relationships by dedicating the majority of the federal funding and opportunities to the commercial space industry and left the government space industry in search of an approach to collaborate with the dominant organization, the commercial space industry service providers. The space industry government agencies, Air Force Space Command (AFSPC) and National Aeronautics and Space Administration (NASA) had realized that to gain resources in the new commercially oriented economic environment, they had to work together and possess the capabilities aligned with the National Space Policy's documented goals. Multi-organizational collaboration in space industry programs is challenging, as NASA, AFSPC, and commercial providers, follow different [1] enterprise architecture guidance such as the NASA systems engineering Handbook, MIL-STD-499 and "A Guide to the systems engineering Body of Knowledge" by the International Council on systems engineering [2] [3]. A solution to streamline their enterprise architecture documentation and meet National Space Policy goals is the Multi-User Architecture Maturity Model Methodology (MAM3), which offers a tailored systems engineering technique the government agencies and private companies can implement for the program's maturity level. In order to demonstrate the MAM3, a CubeSat motivated study was conducted partnering a commercial provider with a government agency. A survey of the commercial space industry service providers' capabilities was performed to select the private companies for the study. Using the survey results, the commercial space industry service providers were ranked using the Analytic Hierarchy Process (AHP) [4]. The AHP is a structured technique for making complex decisions for representing and quantifying its weights, relating those weights to overall goals, and evaluating alternative solutions [5] - [8]. The weights

  1. Architectural communication: Intra and extra activity of architecture

    Directory of Open Access Journals (Sweden)

    Stamatović-Vučković Slavica

    2013-01-01

    Full Text Available Apart from a brief overview of architectural communication viewed from the standpoint of theory of information and semiotics, this paper contains two forms of dualistically viewed architectural communication. The duality denotation/connotation (”primary” and ”secondary” architectural communication is one of semiotic postulates taken from Umberto Eco who viewed architectural communication as a semiotic phenomenon. In addition, architectural communication can be viewed as an intra and an extra activity of architecture where the overall activity of the edifice performed through its spatial manifestation may be understood as an act of communication. In that respect, the activity may be perceived as the ”behavior of architecture”, which corresponds to Lefebvre’s production of space.

  2. Contaminant profiles in Southeast Asian immigrants consuming fish from polluted waters in northeastern Wisconsin

    Energy Technology Data Exchange (ETDEWEB)

    Schantz, Susan L., E-mail: schantz@illinois.edu [Department of Veterinary Biosciences, College of Veterinary Medicine, University of Illinois at Urbana-Champaign, 2001 South Lincoln Avenue, Urbana, IL 61802 (United States); Gardiner, Joseph C. [Department of Epidemiology, Michigan State University (United States); Aguiar, Andrea [Department of Veterinary Biosciences, College of Veterinary Medicine, University of Illinois at Urbana-Champaign, 2001 South Lincoln Avenue, Urbana, IL 61802 (United States); Tang, Xiaoqin; Gasior, Donna M. [Department of Epidemiology, Michigan State University (United States); Sweeney, Anne M. [Department of Epidemiology and Biostatistics, Texas A and M University System Health Science Center USA (United States); Peck, Jennifer D. [Department of Biostatistics and Epidemiology, University of Oklahoma Health Sciences Center (United States); Gillard, Douglas; Kostyniak, Paul J. [Toxicology Research Center, University at Buffalo (United States)

    2010-01-15

    Recent immigrants to the USA from Southeast Asia may be at higher risk of exposure to fish-borne contaminants including polychlorinated biphenyls (PCBs), p, p'-dichlorodiphenyldichloroethene (DDE) and methylmercury (MeHg) because of their propensity to engage in subsistence fishing. Exposure to contaminants was assessed in men and women of Hmong descent living in Green Bay, Wisconsin, where the Fox River and lower Green Bay are contaminated with PCBs, and to a lesser extent with mercury. Serum samples from 142 people were analyzed for PCBs and p,p'-DDE by capillary column gas chromatography with electron capture detection (ECD). Whole blood was analyzed for total mercury by cold vapor atomic absorption spectrometry and atomic fluorescence spectroscopy. Lipid-adjusted total PCB concentrations ranged from 8.7 to 3,091 ng/g (full range of the data), with a geometric mean of 183.6 ng/g (estimated after eliminating one outlier). DDE ranged from 0.3 to 7,083 (full range of the data) with a geometric mean of 449.8 ng/g (estimated after eliminating two outliers). Men had higher PCB and DDE concentrations than women. Serum PCB concentrations were significantly correlated with fish consumption (r=0.43, p<0.0001), whereas DDE concentrations were not (r=0.09,p=0.29). Instead, serum DDE was strongly associated with the number of years spent in a Thai refugee camp before immigrating to the USA (r=0.60;p<0.0001). PCB congeners 138, 153, 118 and 180 accounted for a smaller percentage of the total PCBs than has been reported in other fish-eating populations, and several lightly chlorinated congeners were present in relatively large amounts. Mercury exposure was low in this population. In conclusion, Hmong immigrants in northeastern Wisconsin are at risk of elevated PCB exposure from consumption of locally caught fish. The pattern of exposure is somewhat different than patterns in other fish-eating populations, possibly due to use of Aroclor 1242 by the paper industry in

  3. Contaminant profiles in Southeast Asian immigrants consuming fish from polluted waters in northeastern Wisconsin

    International Nuclear Information System (INIS)

    Schantz, Susan L.; Gardiner, Joseph C.; Aguiar, Andrea; Tang, Xiaoqin; Gasior, Donna M.; Sweeney, Anne M.; Peck, Jennifer D.; Gillard, Douglas; Kostyniak, Paul J.

    2010-01-01

    Recent immigrants to the USA from Southeast Asia may be at higher risk of exposure to fish-borne contaminants including polychlorinated biphenyls (PCBs), p, p'-dichlorodiphenyldichloroethene (DDE) and methylmercury (MeHg) because of their propensity to engage in subsistence fishing. Exposure to contaminants was assessed in men and women of Hmong descent living in Green Bay, Wisconsin, where the Fox River and lower Green Bay are contaminated with PCBs, and to a lesser extent with mercury. Serum samples from 142 people were analyzed for PCBs and p,p'-DDE by capillary column gas chromatography with electron capture detection (ECD). Whole blood was analyzed for total mercury by cold vapor atomic absorption spectrometry and atomic fluorescence spectroscopy. Lipid-adjusted total PCB concentrations ranged from 8.7 to 3,091 ng/g (full range of the data), with a geometric mean of 183.6 ng/g (estimated after eliminating one outlier). DDE ranged from 0.3 to 7,083 (full range of the data) with a geometric mean of 449.8 ng/g (estimated after eliminating two outliers). Men had higher PCB and DDE concentrations than women. Serum PCB concentrations were significantly correlated with fish consumption (r=0.43, p<0.0001), whereas DDE concentrations were not (r=0.09,p=0.29). Instead, serum DDE was strongly associated with the number of years spent in a Thai refugee camp before immigrating to the USA (r=0.60;p<0.0001). PCB congeners 138, 153, 118 and 180 accounted for a smaller percentage of the total PCBs than has been reported in other fish-eating populations, and several lightly chlorinated congeners were present in relatively large amounts. Mercury exposure was low in this population. In conclusion, Hmong immigrants in northeastern Wisconsin are at risk of elevated PCB exposure from consumption of locally caught fish. The pattern of exposure is somewhat different than patterns in other fish-eating populations, possibly due to use of Aroclor 1242 by the paper industry in this region.

  4. Port Sunlight, essai architectural et social

    OpenAIRE

    Machet, Laurence

    2017-01-01

    The purpose of this article is to examine the city of Port Sunlight, its history, design and originality. Created by William Lever in 1888 in order to house his newly-built soap factory, Port Sunlight is part of the numerous “factory villages” built in the wake of the industrial revolution according to philanthropic and utilitarian principles. But this article intends to show that Port Sunlight differs from other factory towns. Its careful design, elaborate architecture and public facilities ...

  5. Intelligent Information Retrieval and Web Mining Architecture Using SOA

    Science.gov (United States)

    El-Bathy, Naser Ibrahim

    2010-01-01

    The study of this dissertation provides a solution to a very specific problem instance in the area of data mining, data warehousing, and service-oriented architecture in publishing and newspaper industries. The research question focuses on the integration of data mining and data warehousing. The research problem focuses on the development of…

  6. Characterizing phosphorus dynamics in tile-drained agricultural fieldsof eastern Wisconsin

    Science.gov (United States)

    Madison, Allison; Ruark, Matthew; Stuntebeck, Todd D.; Komiskey, Matthew J.; Good, Laura W.; Drummy, Nancy; Cooley, Eric

    2014-01-01

    Artificial subsurface drainage provides an avenue for the rapid transfer of phosphorus (P) from agricultural fields to surface waters. This is of particular interest in eastern Wisconsin, where there is a concentrated population of dairy farms and high clay content soils prone to macropore development. Through collaboration with private landowners, surface and tile drainage was measured and analyzed for dissolved reactive P (DRP) and total P (TP) losses at four field sites in eastern Wisconsin between 2005 and 2009. These sites, which received frequent manure applications, represent a range of crop management practices which include: two chisel plowed corn fields (CP1, CP2), a no-till corn–soybean field (NT), and a grazed pasture (GP). Subsurface drainage was the dominant pathway of water loss at each site accounting for 66–96% of total water discharge. Average annual flow-weighted (FW) TP concentrations were 0.88, 0.57, 0.21, and 1.32 mg L−1 for sites CP1, CP2, NT, and GP, respectively. Low TP concentrations at the NT site were due to tile drain interception of groundwater flow where large volumes of tile drainage water diluted the FW-TP concentrations. Subsurface pathways contributed between 17% and 41% of the TP loss across sites. On a drainage event basis, total drainage explained between 36% and 72% of the event DRP loads across CP1, CP2, and GP; there was no relationship between event drainflow and event DRP load at the NT site. Manure applications did not consistently increase P concentrations in drainflow, but annual FW-P concentrations were greater in years receiving manure applications compared to years without manure application. Based on these field measures, P losses from tile drainage must be integrated into field level P budgets and P loss calculations on heavily manured soils, while also acknowledging the unique drainage patterns observed in eastern Wisconsin.

  7. Parasite infections in nestling red-shouldered hawks (Buteo lineatus) in northeast Wisconsin.

    Science.gov (United States)

    King, Janet C; Dubay, Shelli A; Huspeni, Todd C; VanLanen, Andrew R; Gerhold, Richard W

    2010-06-01

    Red-shouldered hawks (Buteo lineatus) are threatened in Wisconsin and long-term data suggest that nest productivity is low in the state for unknown reasons. Our objective was to determine whether red-shouldered hawks in northeast Wisconsin were infected with parasites that could contribute to low nest productivity. We examined nestlings for the presence of Trichomonas gallinae, Protocalliphora avium, and blood parasites in June 2006 and 2007. We did not detect T. gallinae in throat swabs taken from 24 nestlings in 2007. Ear canals of nestlings were parasitized by P. avium larvae in 10 of 11 (91%) nests and in 22 of 24 (92%) nestlings. Larvae were found in higher intensity in 1 ear relative to the other. Leucocytozoon toddi was present in 90.5% (38/42) of the nestlings. At least 1 bird in each nest was infected. Intensity of L. toddi averaged 48.6 +/- 58.3 infected cells per 2,000 erythrocytes (2.4 +/- 2.9%). No other blood parasites were identified.

  8. Flood of July 2016 in northern Wisconsin and the Bad River Reservation

    Science.gov (United States)

    Fitzpatrick, Faith A.; Dantoin, Eric D.; Tillison, Naomi; Watson, Kara M.; Waschbusch, Robert J.; Blount, James D.

    2017-06-06

    Heavy rain fell across northern Wisconsin and the Bad River Reservation on July 11, 2016, as a result of several rounds of thunderstorms. The storms caused major flooding in the Bad River Basin and nearby tributaries along the south shore of Lake Superior. Rainfall totals were 8–10 inches or more and most of the rain fell in an 8-hour period. A streamgage on the Bad River near Odanah, Wisconsin, rose from 300 cubic feet per second to a record peak streamflow of 40,000 cubic feet per second in only 15 hours. Following the storms and through September 2016, personnel from the U.S. Geological Survey and Bad River Tribe Natural Resources Department recovered and documented 108 high-water marks near the Bad River Reservation. Many of these high-water marks were used to create three flood-inundation maps for the Bad River, Beartrap Creek, and Denomie Creek for the Bad River Reservation in the vicinity of the community of Odanah.

  9. Cover Crop (Rye) and No-Till System in Wisconsin

    OpenAIRE

    Alföldi, Thomas

    2014-01-01

    Erin Silva, University of Wisconsin, describes an organic no-till production technique using rye as cover crop to suppress weeds in the following production season. Using a roller-crimper, the overwintering rye is terminated at the time of cash crop planting, leaving a thick mat of plant residue on the soil surface. Soybeans are sown directly into the cover crop residue, allowing the cash crop to emerge through the terminated cover crop while suppressing weeds throughout the season. W...

  10. Modeling the Precambrian Topography of Columbia County, Wisconsin Using Two-Dimensional Models of Gravity and Aeromagnetic Data

    Science.gov (United States)

    Rasmussen, J.; Skalbeck, J.; Stewart, E.

    2017-12-01

    The deep sandstone and dolomite aquifer of Wisconsin is the primary source of water in the central, southern, and western portions of the state, as well as a supplier for many high-capacity wells in the eastern portion. This prominent groundwater system is highly impacted by the underlying Precambrian basement, which includes the doubly plunging Baraboo Syncline in Columbia and Sauk Counties. This project is a continuation of previous work done in Dodge and Fond du Lac Counties by the University of Wisconsin-Parkside (UW-P) and the Wisconsin Geological & Natural History Survey (WGNHS). The goal of this project was to produce of an updated Precambrian topographic map of southern Wisconsin, by adding Gravity and Aeromagnetic data to the existing map which is based mainly on sparse outcrop and well data. Gravity and Aeromagnetic data from the United States Geological Survey (USGS) was processed using GM-SYS 3D modeling software in Geosoft Oasis Montaj. Grids of subsurface layers were created from the data and constrained by well and drilling records. The Columbia County basement structure is a complex network of Precambrian granites and rhyolites which is non-conformably overlain by quartzite, slate, and a layer of iron rich sedimentary material. Results from previously collected cores as well as drilling done in neighboring Dodge County, show that the iron rich layer was draped over much of the Baraboo area before being subject to the multitude of folding and faulting events that happened in the region during the late Precambrian. This layer provides telltale signatures that aided in construction of the model due to having an average density of 3.7 g/cm3 and a magnetic susceptibility of 8000 x 10-6 cgs, compared to the average density and susceptibility of the rest of the bedrock being 2.8 g/cm3 and 1500 x 10-6 cgs, respectively. The research done on the Columbia County basement is one part of a larger project aimed at improving groundwater management efforts of the

  11. How energy efficiency fails in the building industry

    International Nuclear Information System (INIS)

    Ryghaug, Marianne; Sorensen, Knut H.

    2009-01-01

    This paper examines how energy efficiency fails in the building industry based on many years of research into the integration of energy efficiency in the construction of buildings and sustainable architecture in Norway. It argues that energy-efficient construction has been seriously restrained by three interrelated problems: (1) deficiencies in public policy to stimulate energy efficiency, (2) limited governmental efforts to regulate the building industry, and (3) a conservative building industry. The paper concludes that innovation and implementation of new, energy-efficient technologies in the building industry requires new policies, better regulations and reformed practices in the industry itself

  12. Dairy sheep production research at the University of Wisconsin-Madison, USA – a review

    Science.gov (United States)

    2014-01-01

    Commercial milking of sheep is a new agricultural industry in the United States starting approximately 30 yr ago. The industry is still small, but it is growing. The majority of the sheep milk is used in the production of specialty cheeses. The United States is the major importer of sheep milk cheeses with 50 to 60% of annual world exports coming to the United States during the past 20 yr. Therefore, there is considerable growth potential for the industry in the United States. The only dairy sheep research flock in North America is located at the Spooner Agricultural Research Station of the University of Wisconsin-Madison. The research program started in 1993 and has been multifaceted; dealing with several areas important to commercial dairy sheep farmers. The East Friesian and Lacaune dairy breeds were compared and introduced to the industry through the research program. Both dairy breeds produced significantly more milk than traditional meat-wool breeds found in the U.S., but the two breeds differed in their production traits. East Friesian-cross ewes produced more lambs and slightly more milk than Lacaune-cross ewes whereas Lacaune-cross ewes produced milk with a higher percentage of fat and protein than East Friesian-cross ewes. Lactation physiology studies have shown that ewes with active corpora lutea have increased milk yields, oxytocin release during milking is required to obtain normal fat percentages in the milk, large udder cisterns of dairy ewes can allow for increased milking intervals, and short daylengths during late pregnancy results in increased milk yield. In the nutrition area, legume-grass pastures and forages with a higher percentage of legume will result in increased milk production. Grazing ewes respond to additional supplementation with increased milk yield, but it is important to match the supplement to the quality of the grazing. Ewes on high quality legume-grass pastures that are high in rumen degradable protein respond with increased

  13. Enterprise architecture evaluation using architecture framework and UML stereotypes

    Directory of Open Access Journals (Sweden)

    Narges Shahi

    2014-08-01

    Full Text Available There is an increasing need for enterprise architecture in numerous organizations with complicated systems with various processes. Support for information technology, organizational units whose elements maintain complex relationships increases. Enterprise architecture is so effective that its non-use in organizations is regarded as their institutional inability in efficient information technology management. The enterprise architecture process generally consists of three phases including strategic programing of information technology, enterprise architecture programing and enterprise architecture implementation. Each phase must be implemented sequentially and one single flaw in each phase may result in a flaw in the whole architecture and, consequently, in extra costs and time. If a model is mapped for the issue and then it is evaluated before enterprise architecture implementation in the second phase, the possible flaws in implementation process are prevented. In this study, the processes of enterprise architecture are illustrated through UML diagrams, and the architecture is evaluated in programming phase through transforming the UML diagrams to Petri nets. The results indicate that the high costs of the implementation phase will be reduced.

  14. Developing product families based on architectures

    DEFF Research Database (Denmark)

    Harlou, Ulf

    2006-01-01

    family master plan (PFMP). The PFMP aims at modelling product families and especially variety of product families. The results of this thesis build on research literature and experiences from the industrial partners. Extensive verifications of the theory contributions, models and tools have been carried......The subject of this PhD thesis is development of product families based on architectures. Companies are introducing more and more product variants to fulfil the market demands. These new variants add complexity to many of the processes and systems in the companies. Reuse of standard designs (i.......e. design entities) and re-use of the way new products are developed can simplify the processes and systems. Case studies show that reuse can lead to reduction of cost and time-to-market of new products. One of the means for managing reuse of standard designs within product families are architectures...

  15. Natural photonics for industrial inspiration.

    Science.gov (United States)

    Parker, Andrew R

    2009-05-13

    There are two considerations for optical biomimetics: the diversity of submicrometre architectures found in the natural world, and the industrial manufacture of these. A review exists on the latter subject, where current engineering methods are considered along with those of the natural cells. Here, on the other hand, I will provide a modern review of the different categories of reflectors and antireflectors found in animals, including their optical characterization. The purpose of this is to inspire designers within the $2 billion annual optics industry.

  16. Software architecture 2

    CERN Document Server

    Oussalah, Mourad Chabanne

    2014-01-01

    Over the past 20 years, software architectures have significantly contributed to the development of complex and distributed systems. Nowadays, it is recognized that one of the critical problems in the design and development of any complex software system is its architecture, i.e. the organization of its architectural elements. Software Architecture presents the software architecture paradigms based on objects, components, services and models, as well as the various architectural techniques and methods, the analysis of architectural qualities, models of representation of architectural templa

  17. Lightweight enterprise architectures

    CERN Document Server

    Theuerkorn, Fenix

    2004-01-01

    STATE OF ARCHITECTUREArchitectural ChaosRelation of Technology and Architecture The Many Faces of Architecture The Scope of Enterprise Architecture The Need for Enterprise ArchitectureThe History of Architecture The Current Environment Standardization Barriers The Need for Lightweight Architecture in the EnterpriseThe Cost of TechnologyThe Benefits of Enterprise Architecture The Domains of Architecture The Gap between Business and ITWhere Does LEA Fit? LEA's FrameworkFrameworks, Methodologies, and Approaches The Framework of LEATypes of Methodologies Types of ApproachesActual System Environmen

  18. Software architecture 1

    CERN Document Server

    Oussalah , Mourad Chabane

    2014-01-01

    Over the past 20 years, software architectures have significantly contributed to the development of complex and distributed systems. Nowadays, it is recognized that one of the critical problems in the design and development of any complex software system is its architecture, i.e. the organization of its architectural elements. Software Architecture presents the software architecture paradigms based on objects, components, services and models, as well as the various architectural techniques and methods, the analysis of architectural qualities, models of representation of architectural template

  19. Indigenous architecture as a context-oriented architecture, a look at ...

    African Journals Online (AJOL)

    What has become problematic as the achievement of international style and globalization of architecture during the time has been the purely technological look at architecture, and the architecture without belonging to a place. In recent decades, the topic of sustainable architecture and reconsidering indigenous architecture ...

  20. 77 FR 48538 - Notice of Inventory Completion: State Historical Society of Wisconsin, Madison, WI

    Science.gov (United States)

    2012-08-14

    ... Historical Society of Wisconsin at the address below by September 13, 2012. ADDRESSES: Jennifer Kolb... Indian tribe that believes it satisfies the criteria in 43 CFR 10.11(c)(1) should contact Jennifer Kolb...

  1. Measuring farm sustainability using data envelope analysis with principal components: the case of Wisconsin cranberry.

    Science.gov (United States)

    Dong, Fengxia; Mitchell, Paul D; Colquhoun, Jed

    2015-01-01

    Measuring farm sustainability performance is a crucial component for improving agricultural sustainability. While extensive assessments and indicators exist that reflect the different facets of agricultural sustainability, because of the relatively large number of measures and interactions among them, a composite indicator that integrates and aggregates over all variables is particularly useful. This paper describes and empirically evaluates a method for constructing a composite sustainability indicator that individually scores and ranks farm sustainability performance. The method first uses non-negative polychoric principal component analysis to reduce the number of variables, to remove correlation among variables and to transform categorical variables to continuous variables. Next the method applies common-weight data envelope analysis to these principal components to individually score each farm. The method solves weights endogenously and allows identifying important practices in sustainability evaluation. An empirical application to Wisconsin cranberry farms finds heterogeneity in sustainability practice adoption, implying that some farms could adopt relevant practices to improve the overall sustainability performance of the industry. Copyright © 2014 Elsevier Ltd. All rights reserved.

  2. Sedimentation History Of Halfway Creek Marsh, Upper Mississippi River National Wildlife And Fish Refuge, Wisconsin, 1846-2006. Scientific Investigations Report 2007–5209

    Science.gov (United States)

    The history of overbank sedimentation in the vicinity of Halfway Creek Marsh near La Crosse, Wisconsin, was examined during 2005-06 by the U.S. Geological Survey and University of Wisconsin-Madison as part of a broader study of sediment and nutrient loadings to the Upper Mississi...

  3. University of Wisconsin, Nuclear Reactor Laboratory. Annual report, 1985-1986

    International Nuclear Information System (INIS)

    Cashwell, R.J.

    1986-01-01

    Operational activities for the reactor are described concerning nuclear engineering classes from the University of Wisconsin; reactor sharing program; utility personnel training; sample irradiations and neutron activation analysis; and changes in personnel, facility, and procedures. Results of surveillance tests are presented for operating statistics and fuel exposure; emergency shutdowns and inadvertent scrams; maintenance; radioactive waste disposal; radiation exposures; environmental surveys; and publications and presentations on work based on reactor use

  4. Architecture in the Islamic Civilization: Muslim Building or Islamic Architecture

    OpenAIRE

    Yassin, Ayat Ali; Utaberta, Dr. Nangkula

    2012-01-01

    The main problem of the theory in the arena of islamic architecture is affected by some of its Westernthoughts, and stereotyping the islamic architecture according to Western thoughts; this leads to the breakdownof the foundations in the islamic architecture. It is a myth that islamic architecture is subjected to theinfluence from foreign architectures. This paper will highlight the dialectical concept of islamic architecture ormuslim buildings and the areas of recognition in islamic architec...

  5. Simulation as a tool for architectural design and evaluation. Resolved patterns from engineering

    Directory of Open Access Journals (Sweden)

    Johanna Trujillo

    2016-04-01

    Full Text Available La simulación como herramienta de diseño y evaluación arquitectónica. Pautas resueltas desde la ingenieríaResumenSe presenta un panorama sobre la importancia del proceso de diseño sostenible aplicado a las edificaciones. Teniendo en cuenta que el sector de la construcción es una de las áreas de más alto impacto ambiental, es importante analizar cuáles serían los nuevos procesos de diseño de las edificaciones en términos de sostenibilidad. Estos conceptos se aplicaron a un estudio de caso por medio de la simulación discreta, la cual permite una evaluación de la capacidad en un edificio junto con sus recursos, a fin de tomar decisiones de ampliación en el proceso de diseño arquitectónico. Los datos se analizaron en el programa estadístico SPSS y se simularon en ProModel. El modelo pedagógico propuesto puede llegar a ser de utilidad al momento de aplicarse en un contexto multidisciplinar, en donde interactúen estudiantes de ingeniería industrial y arquitectura. Este ejercicio puede aplicarse en las aulas de clase; con él se reducirían los tiempos de diseño, y la comunicación entre estudiantes mejoraría porque implica el trabajo multidisciplinar.Palabras clave: diseño arquitectónico, edificios industriales, educación arquitectónica, industria de la construcción, ingeniería industrial.Simulation as a tool for architectural design and evaluation. Resolved patterns from engineeringAbstractAn overview of the importance of sustainable design process applied to buildings is presented. Given that the field of construction is one of the areas with the highest environmental impact, it is important to analyze what would be the new design processes for buildings in terms of sustainability. These concepts were applied to a case study using discrete simulation, which allows an assessment of capacity building along with its resources, to make decisions expansion in the architectural design process. Data were analyzed in the SPSS

  6. A Hybrid Power Management (HPM) Based Vehicle Architecture

    Science.gov (United States)

    Eichenberg, Dennis J.

    2011-01-01

    Society desires vehicles with reduced fuel consumption and reduced emissions. This presents a challenge and an opportunity for industry and the government. The NASA John H. Glenn Research Center (GRC) has developed a Hybrid Power Management (HPM) based vehicle architecture for space and terrestrial vehicles. GRC's Electrical and Electromagnetics Branch of the Avionics and Electrical Systems Division initiated the HPM Program for the GRC Technology Transfer and Partnership Office. HPM is the innovative integration of diverse, state-of-the-art power devices in an optimal configuration for space and terrestrial applications. The appropriate application and control of the various power devices significantly improves overall system performance and efficiency. The basic vehicle architecture consists of a primary power source, and possibly other power sources, providing all power to a common energy storage system, which is used to power the drive motors and vehicle accessory systems, as well as provide power as an emergency power system. Each component is independent, permitting it to be optimized for its intended purpose. This flexible vehicle architecture can be applied to all vehicles to considerably improve system efficiency, reliability, safety, security, and performance. This unique vehicle architecture has the potential to alleviate global energy concerns, improve the environment, stimulate the economy, and enable new missions.

  7. Research Evidence and School Board Deliberations: Lessons from Three Wisconsin School Districts

    Science.gov (United States)

    Asen, Robert; Gurke, Deb; Conners, Pamela; Solomon, Ryan; Gumm, Elsa

    2013-01-01

    This article analyzes the use of research evidence in school-board deliberations in three school districts in Wisconsin. In these settings, the circulation, meaning, and function of research depended importantly on the interests and backgrounds of advocates, the composition of audiences, and the values and contexts of decision-making. Board…

  8. Wisconsin System for Instructional Management: Terminal Operator Manual. Practical Paper No. 19.

    Science.gov (United States)

    Bozeman, William C.; And Others

    The Wisconsin System for Instructional Management (WIS-SIM) is a computer managed instruction (CMI) system designed to improve instructional decision making in order to maximize the educational progress of each child while making efficient use of the available human, material, and financial resources within an organizational structure such as the…

  9. An Examination of Alternative Poverty Measures for the Wisconsin Equalization Aid Formula.

    Science.gov (United States)

    Cibulka, James G.

    1986-01-01

    Wisconsin's guaranteed tax base equalization formula has no direct adjustment for the additional costs of educating poverty level pupils. This paper establishes the need for an adjustment and examines three measures (based on varying poverty definitions) to determine which provides the most equitable funding formula for educating poor children. (9…

  10. Development of Landscape Architecture through Geo-eco-tourism in Tropical Karst Area to Avoid Extractive Cement Industry for Dignified and Sustainable Environment and Life

    Science.gov (United States)

    Cahyanti, Pita A. B.; Agus, Cahyono

    2017-08-01

    Karst areas in Indonesia amounted to 154,000 km2, potentially for extractive cement and wall paint industries. Exploitation of karst caused serious problems on the environment, health and social culture of the local community. Even though, karst region as a natural and cultural world heritage also have potential environmental services such as water resources, carbon sink, biodiversity, unique landscapes, natural caves, natural attractions, archaeological sites and mystic areas. Landscape architectural management of in the concept of blue revolution through the empowerment of land resources (soil, water, minerals) and biological resources (plant, animal, human), not only have adding value of economy aspect but also our dignified and sustainable environment and life through health, environmental, social, cultural, technological and management aspects. Geo-eco-tourism offers the efficiency of investment, increased creative innovation, increased funding, job creation, social capital development, stimulation of the socio-entrepreneurship in community. Community based geo-eco-tourism in Gunung Kidul Yogyakarta rapidly growing lately due to the local government banned the exploitation of karst. Landscape architecture at the caves, white sand beaches, cliffs in karst areas that beautiful, artistic and have special rare natural architecture form of stalactite and stalagmite, become the new phenomenal interested object of geo-eco-tourism. Many hidden nature objects that had been deserted and creepy could be visited by many local and foreign tourists. Landscape architectural management on hilltops with a wide view of the universe and fresh, sunset and sunrise, the clouds country are a rare sight for modern community. Local cultural attractions, local culinary, home stay with local communities will be an added attraction, but the infrastructure and human resources should be developed. Traveler photographs that widespread rapidly through social media and mass media became a

  11. Optimizing engineering tools using modern ground architectures

    OpenAIRE

    McArdle, Ryan P.

    2017-01-01

    Approved for public release; distribution is unlimited Over the past decade, a deluge of large and complex datasets (aka big data) has overwhelmed the scientific community. Traditional computing architectures were not capable of processing the data efficiently, or in some cases, could not process the data at all. Industry was forced to reexamine the existing data processing paradigm and develop innovative solutions to address the challenges. This thesis investigates how these modern comput...

  12. Fueling Wisconsin's economy with renewable energy

    International Nuclear Information System (INIS)

    Clemmer, S.

    1995-01-01

    A dynamic macroeconomic model of the Wisconsin economy is used to estimate the economic impacts of displacing a portion of future investment in fossil fuel power plants (coal and natural gas) with renewable energy resources (biomass, wind, solar and hydro). The results show that renewable energy investments produce over three times more jobs, income and economic activity than the same amount of electricity generated from coal and natural gas power plants. Between 1995 and 2020, a 75% increase in renewable energy use generates approximately 65,000 more job-years of employment, $1.6 billion in higher disposable income and a $3.1 billion increase in gross regional product than conventional power plant investments. This includes the effects of a 0.3% average annual increase in electricity prices from renewable energy investments

  13. Interplay between requirements, software architecture, and hardware constraints in the development of a home control user interface

    DEFF Research Database (Denmark)

    Loft, M.S.; Nielsen, S.S.; Nørskov, Kim

    2012-01-01

    is to propose the hardware platform as a third Twin Peaks element that must be given attention in projects such as the one described in this paper. Specifically, we discuss how the presence of severe hardware constraints exacerbates making trade-offs between requirements and architecture.......We have developed a new graphical user interface for a home control device for a large industrial customer. In this industrial case study, we first present our approaches to requirements engineering and to software architecture; we also describe the given hardware platform. Then we make two...... contributions. Our first contribution is to provide a specific example of a real-world project in which a Twin Peaks-compliant approach to software development has been used, and to describe and discuss three examples of interplay between requirements and software architecture decisions. Our second contribution...

  14. Central system of Interlock of ITER, high integrity architecture

    International Nuclear Information System (INIS)

    Prieto, I.; Martinez, G.; Lopez, C.

    2014-01-01

    The CIS (Central Interlock System), along with the CODAC system and CSS (Central Safety System), form the central I and C systems of ITER. The CIS is responsible for implementing the core functions of protection (Central Interlock Functions) through different systems of plant (Plant Systems) within the overall strategy of investment protection for ITER. IBERDROLA supports engineering to define and develop the control architecture of CIS according to the stringent requirements of integrity, availability and response time. For functions with response times of the order of half a second is selected PLC High availability of industrial range. However, due to the nature of the machine itself, certain functions must be able to act under the millisecond, so it has had to develop a solution based on FPGA (Field Programmable Gate Array) capable of meeting the requirements architecture. In this article CIS architecture is described, as well as the process for the development and validation of the selected platforms. (Author)

  15. Thirty-two years of landscape architectural education in Indonesia: a retrospect and prospect

    Directory of Open Access Journals (Sweden)

    Jusna Amin

    1995-03-01

    Full Text Available Study programmes in landscape architecture have existed in Indonesia since the establishment of its first educational institution in 1963. This article presents a retrospective assessment which, hopefully, will encourage all those who arc concerned with landscape architecture in Indonesia to think about its future development. For the author, the article updates a previous paper about the status of the educational practice in Indonesia, delivered as a supporting document at the 4th IFLA Eastern Regional conference in Singapore in 1981, under the theme of 'Education'. The article begins with a systematic review of landscape architecture in Indonesia, and then presents results of six interviews with individuals chosen to represent a range of views from government, private practice, and educators. From both the review and interview results, questions are considered about people's perception and appreciation of landscape architecture in Indonesia as a branch of education and professional practice. Two specific priorities are highlighted. One is the recognised need for landscape architecture to make meaningful connections between people and the places they live in. The second focuses on the relationship between landscape education and the service and industrial sectors, with regard to the availability of job opportunities for its graduates. The article includes a profile of the profession in Indonesia and asks whether the profession is able to apply environmental approaches and techniques for community involvement in the planning and design process. Ideas arc discussed regarding the improvement of the quality of university graduates to produce educated human resources who will meet the current requirements of national development and the industrial sector.

  16. ADA Compliance and Accessibility of Fitness Facilities in Western Wisconsin.

    Science.gov (United States)

    Johnson, Marquell J; Stoelzle, Hannah Y; Finco, Kristi L; Foss, Sadie E; Carstens, Katie

    2012-01-01

    The study expands the research on fitness facility accessibility by determining how compliant fitness facilities in rural western Wisconsin were with Title III of the Americans with Disabilities Act (ADA). Comparisons were made with 4 other studies that were conducted in different geographical regions. The study also examined fitness professionals' disability knowledge and awareness. An ADA fitness facility compliance instrument and a fitness professional disability awareness survey were used. Direct observation and physical measurements were taken during on-site visits to 16 of 36 eligible fitness facilities in rural western Wisconsin. Ten fitness professionals from participating facilities completed an online survey. Frequencies were used to analyze the results. None of the participating facilities were in 100% compliance with ADA. Customer service desk (84%) and path of travel throughout the facility (72%) were the highest compliance areas. Telephone (6%) and locker rooms (32%) were the lowest compliance areas. No fitness professional was trained in wheelchair transfers and very few had received training in providing services to individuals with disabilities. Fitness facility accessibility remains a concern nationally. Continued efforts need to be made to raise the awareness of ADA compliance among fitness professionals across the United States, especially in rural areas where fitness facility availability is limited.

  17. The new landscape of parallel computer architecture

    International Nuclear Information System (INIS)

    Shalf, John

    2007-01-01

    The past few years has seen a sea change in computer architecture that will impact every facet of our society as every electronic device from cell phone to supercomputer will need to confront parallelism of unprecedented scale. Whereas the conventional multicore approach (2, 4, and even 8 cores) adopted by the computing industry will eventually hit a performance plateau, the highest performance per watt and per chip area is achieved using manycore technology (hundreds or even thousands of cores). However, fully unleashing the potential of the manycore approach to ensure future advances in sustained computational performance will require fundamental advances in computer architecture and programming models that are nothing short of reinventing computing. In this paper we examine the reasons behind the movement to exponentially increasing parallelism, and its ramifications for system design, applications and programming models

  18. The new landscape of parallel computer architecture

    Energy Technology Data Exchange (ETDEWEB)

    Shalf, John [NERSC Division, Lawrence Berkeley National Laboratory 1 Cyclotron Road, Berkeley California, 94720 (United States)

    2007-07-15

    The past few years has seen a sea change in computer architecture that will impact every facet of our society as every electronic device from cell phone to supercomputer will need to confront parallelism of unprecedented scale. Whereas the conventional multicore approach (2, 4, and even 8 cores) adopted by the computing industry will eventually hit a performance plateau, the highest performance per watt and per chip area is achieved using manycore technology (hundreds or even thousands of cores). However, fully unleashing the potential of the manycore approach to ensure future advances in sustained computational performance will require fundamental advances in computer architecture and programming models that are nothing short of reinventing computing. In this paper we examine the reasons behind the movement to exponentially increasing parallelism, and its ramifications for system design, applications and programming models.

  19. Modular Integrated Monitoring System (MIMS) - architecture and implementation

    International Nuclear Information System (INIS)

    Funkhouser, D.R.; Davidson, G.W.; Deland, S.M.

    1997-01-01

    The MIMS is being developed as a cost-effective means of performing safeguards in unattended remote monitoring applications. Based on industry standards and an open systems approach, the MIMS architecture supports both data acquisition and data review subsystems. Data includes images as well as discrete and analog sensor outputs. The MIMS uses an Echelon LonWorks network as a standard means and method of data acquisition from the sensor. A common data base not only stores sensor and image data but also provides a structure by which dynamic changes to the sensor system can be reflected in the data acquisition and data review subsystems without affecting the execution software. The architecture includes standards for wide area communications between data acquisition systems and data review systems. Data authentication is provided as an integral part of the design. The MIMS software implements this architecture by combining the use of commercial applications with a set of custom 16 and 32 bit Microsoft Windows applications which are run under Windows NT and Windows 95 operating systems

  20. 75 FR 32813 - St. Croix Chippewa Indians of Wisconsin Alcoholic Beverage Control Ordinance

    Science.gov (United States)

    2010-06-09

    ... DEPARTMENT OF THE INTERIOR Bureau of Indian Affairs St. Croix Chippewa Indians of Wisconsin...: This notice publishes the Secretary's certification of the amended St. Croix Chippewa Indians of... Country. The St. Croix Tribal Council of the adopted this amended Liquor Ordinance on December 3, 2009...

  1. How Productive Are Southeastern Wisconsin Schools? Regional Report. Volume 3, Number 10

    Science.gov (United States)

    Schmidt, Jeffrey K.; Lemke, Melissa

    2006-01-01

    Public schools can be considered a form of workforce development, and thus it is important to measure the "work product" of the schools. The Public Policy Forum's annual analysis of public schools in the 50 districts serving southeastern Wisconsin measured absenteeism as educational opportunities lost because children were not in class.…

  2. Software architecture analysis tool : software architecture metrics collection

    NARCIS (Netherlands)

    Muskens, J.; Chaudron, M.R.V.; Westgeest, R.

    2002-01-01

    The Software Engineering discipline lacks the ability to evaluate software architectures. Here we describe a tool for software architecture analysis that is based on metrics. Metrics can be used to detect possible problems and bottlenecks in software architectures. Even though metrics do not give a

  3. Hydrologic, ecologic, and geomorphic responses of Brewery Creek to construction of a residential subdivision, Dane County, Wisconsin, 1999-2002

    Science.gov (United States)

    Selbig, William R.; Jopke, Peter L.; Marhshall, David W.; Sorge, Michael J.

    2004-01-01

    The U.S. Geological Survey (USGS), in cooperation with the Dane County Land Conservation Department (LCD) and the Wisconsin Department of Natural Resources (DNR), investigated the instream effects from construction of a residential subdivision on Brewery Creek in Dane County, Wisconsin. The purpose of the investigation was to determine whether a variety of storm-runoff and erosion-control best-management practices (BMPs) would effectively control the overall sediment load, as well as minimize any hydrologic, ecologic, and geomorphic stresses to Brewery Creek.

  4. Social and cultural capital in project marketing service firms: Danish architectural firms on the German market

    DEFF Research Database (Denmark)

    Skaates, Maria Anne; Tikkanen, Henrikki; Alajoutsijärvi, Kimmo

    2002-01-01

    This article analyses the marketing activities of three Danish architectural firms in Germany during the 1990s from a perspective that is new to project marketing, in that the Bourdivan concepts of social and cultural capital are applied to the offerings and activities of firms. In architecture...... provide support for our claim that the accumulation of social and cultural capital is crucial to acquiring architectural projects, while also indicating that cultural and social capital are internationally transferable to a limited extent only. This in turn suggests that national construction industries...

  5. Open architecture design and approach for the Integrated Sensor Architecture (ISA)

    Science.gov (United States)

    Moulton, Christine L.; Krzywicki, Alan T.; Hepp, Jared J.; Harrell, John; Kogut, Michael

    2015-05-01

    Integrated Sensor Architecture (ISA) is designed in response to stovepiped integration approaches. The design, based on the principles of Service Oriented Architectures (SOA) and Open Architectures, addresses the problem of integration, and is not designed for specific sensors or systems. The use of SOA and Open Architecture approaches has led to a flexible, extensible architecture. Using these approaches, and supported with common data formats, open protocol specifications, and Department of Defense Architecture Framework (DoDAF) system architecture documents, an integration-focused architecture has been developed. ISA can help move the Department of Defense (DoD) from costly stovepipe solutions to a more cost-effective plug-and-play design to support interoperability.

  6. Wisconsin's Lake Superior Basin Water Quality Study. Supplement. Technical Report No. 2.

    Science.gov (United States)

    Whisnant, David M., Ed.

    During the period extending from May 1972 through April 1973, an investigation of the overall water quality conditions of streams flowing into Lake Superior from the entire state of Wisconsin was conducted. The goal of this publication was to provide much needed regional information on water quality, drainage basins, pollution sources and loads,…

  7. 75 FR 10309 - Wisconsin Statewide Habitat Conservation Plan for Karner Blue Butterfly

    Science.gov (United States)

    2010-03-05

    ... implementation of the HCP, which has become the normal way of doing business in Wisconsin. Partners and other... management that incidentally takes butterflies could not proceed. Vegetation succession would follow and the... normal business hours (8 a.m. to 4:30 p.m.) at the Ecological Services Field Office in New Franken and at...

  8. Architectural and Urban Identity Transformation of Eskisehir - An Anatolian City

    Science.gov (United States)

    Kandemir, Ozlem

    2017-10-01

    City is the arena where we identify ourselves and interact with others and our environment; cities are epicentres of interaction, transition and fusion of different communities and their cultures. Thus, it is important to discuss the elements of change and their consequences in architectural - urban spaces and their products in the context of identity. Urban identity can be defined as the impression invoked on its inhabitants by the environmental, historical, sociocultural and spatial values. Both architectural and urban identity have a dynamic structure, susceptive to every change on both social and administrative structure. Both global and national economic fluctuations in the last decades and industrialisation throughout the 20th century caused dramatic and diverse changes in the conditions of life, consumption forms, the perception of time and space consequently transforming architecture and city. The changes in all the different aspects of the city life and structure with time cause transformation of architecture and urban identity. This dynamism caused by changes and new formations in the cultural life and environmental conditions also leads to transforming customs and the ways we occupy/use/live in a place. Consequently, these changes and new social norms that can transform the way we occupy a space and our demands from a place can be asserted. All new requirements caused by these new conditions of urban life transform the existing architecture and spaces. In this presentation, the transformation of the architectural and urban identity of Eskisehir will be discussed through its dynamics like architectural and urban transformation, industry and politics.

  9. Mobile opportunistic networks architectures, protocols and applications

    CERN Document Server

    Denko, Mieso K

    2011-01-01

    Widespread availability of pervasive and mobile devices coupled with recent advances in networking technologies make opportunistic networks one of the most promising communication technologies for a growing number of future mobile applications. Covering the basics as well as advanced concepts, this book introduces state-of-the-art research findings, technologies, tools, and innovations. Prominent researchers from academia and industry report on communication architectures, network algorithms and protocols, emerging applications, experimental studies, simulation tools, implementation test beds,

  10. Analysis of Architecture Pattern Usage in Legacy System Architecture Documentation

    NARCIS (Netherlands)

    Harrison, Neil B.; Avgeriou, Paris

    2008-01-01

    Architecture patterns are an important tool in architectural design. However, while many architecture patterns have been identified, there is little in-depth understanding of their actual use in software architectures. For instance, there is no overview of how many patterns are used per system or

  11. Current hybrid-electric powertrain architectures: Applying empirical design data to life cycle assessment and whole-life cost analysis

    International Nuclear Information System (INIS)

    Hutchinson, Tim; Burgess, Stuart; Herrmann, Guido

    2014-01-01

    Highlights: • Design data for 44 hybrid cars available in the US has been gathered and analysed. • An empirical life cycle assessment of greenhouse gas emissions is performed. • Empirical whole-life cost modelling is used to evaluate powertrain architectures. • The value to be seen in each architecture is highly dependent on its application. • Mild, HSD and Plug-in HSD powertrains are the most likely architectures to dominate. - Abstract: The recent introduction of hybrid-electric powertrain technology has disrupted the automotive industry, causing significant powertrain design divergence. As this radical powertrain innovation matures, will hybrid vehicles dominate the future automotive market and does this represent a positive shift in the environmental impact of the industry? The answer to this question is sought within this paper. It seeks to take advantage of the position that the industry has reached, replacing previous theoretical studies with the first extensive empirical models of life cycle emissions and whole-life costing. A comprehensive snapshot of today’s hybrid market is presented, with detailed descriptions of the various hybrid powertrain architectures. Design data has been gathered for 44 hybrid passenger cars currently available in the US. The empirical data is used to explore the relative life cycle greenhouse gas emissions and whole-life costing of different hybrid powertrain architectures. Potential dominant designs are identified and their emissions are shown to be reduced. However, both the emissions and economic competitiveness of different hybrid powertrains are shown to vary significantly depending on how the vehicle is used

  12. Wisconsin health practice rebrands image with "life has its moments" campaign.

    Science.gov (United States)

    2007-01-01

    Wisconsin's largest healthcare system has 41 clinics throughout the state and offers a variety of services, from women's health to oncology. Maintaining a consistent brand message in a large organization with so many product lines requires constant marketing to ensure consumer awareness. To that end, Marshfield Clinic recently launched an effort to revitalize its brand and spread its message, through television spots, print ads, and billboards.

  13. 76 FR 26681 - Wisconsin: Incorporation by Reference of Approved State Hazardous Waste Management Program

    Science.gov (United States)

    2011-05-09

    ... of Approved State Hazardous Waste Management Program AGENCY: Environmental Protection Agency (EPA... Hazardous Waste Management Programs,'' Wisconsin's authorized hazardous waste program. EPA will incorporate... that are authorized and that the EPA will enforce under the Solid Waste Disposal Act, commonly referred...

  14. Connecting Architecture and Implementation

    Science.gov (United States)

    Buchgeher, Georg; Weinreich, Rainer

    Software architectures are still typically defined and described independently from implementation. To avoid architectural erosion and drift, architectural representation needs to be continuously updated and synchronized with system implementation. Existing approaches for architecture representation like informal architecture documentation, UML diagrams, and Architecture Description Languages (ADLs) provide only limited support for connecting architecture descriptions and implementations. Architecture management tools like Lattix, SonarJ, and Sotoarc and UML-tools tackle this problem by extracting architecture information directly from code. This approach works for low-level architectural abstractions like classes and interfaces in object-oriented systems but fails to support architectural abstractions not found in programming languages. In this paper we present an approach for linking and continuously synchronizing a formalized architecture representation to an implementation. The approach is a synthesis of functionality provided by code-centric architecture management and UML tools and higher-level architecture analysis approaches like ADLs.

  15. Converted Industrial Buildings : Where Past and Present Live in Formal Unity

    NARCIS (Netherlands)

    Rogic, T.

    2009-01-01

    This thesis deals with design guidelines, as defined in the field of architectural conservation, by focusing on the problem of the conversion of industrial buildings. It is generally agreed that the best way to secure the future life of industrial heritage is through their adaptive reuse. The former

  16. Learning Vicariously: Tourism, Orientalism and the Making of an Architectural Photography Collection of Egypt

    Directory of Open Access Journals (Sweden)

    Elvan Cobb

    2017-01-01

    Full Text Available Andrew Dickson White, the first president of Cornell University in the United States, referred to architecture as his 'pet extravagance.' Leveraging his influential position as president, White was instrumental in the establishment of the architecture department in 1871. One of his noteworthy contributions to this newly founded department was the initiation of an architectural photography collection that was a direct result of his travels around the world as a diplomat, a scholar and, eventually, as a tourist. This architectural photography collection formed the core of the architectural history education at the school well into the 20th century. At that time, photographs provided one of the only ways for students to learn about the architecture of distant places. White’s selection of architectural subjects, however, was shaped not through deep scholarly inquiry, but rather by the nascent tourist industry. This paper examines White's Egyptian collection, acquired during his voyage to Egypt in 1889. His trip to Egypt, in his own words “marked a new epoch in [his] thinking.” Encountering the 'east' for the first time, White's photography collection both bolstered and challenged the prescribed ways of viewing Egypt and Egyptian architecture, thus having a direct influence on how Cornell students perceived the historic built environment of the ‘east’.

  17. T.Node, industrial version of supernode

    Science.gov (United States)

    Flieller, Sylvain

    1989-12-01

    The Esprit I P1085 "SuperNode" project developed a modular reconfigurable archtecture, based on transputers. This highly parallel machine is now marketed by Telmat Informatique under the name T.Node. This paper presents the P1085 project, the architecture of SuperNode, its industrial implementation and its software enviroment.

  18. A Geo-Distributed System Architecture for Different Domains

    Science.gov (United States)

    Moßgraber, Jürgen; Middleton, Stuart; Tao, Ran

    2013-04-01

    The presentation will describe work on the system-of-systems (SoS) architecture that is being developed in the EU FP7 project TRIDEC on "Collaborative, Complex and Critical Decision-Support in Evolving Crises". In this project we deal with two use-cases: Natural Crisis Management (e.g. Tsunami Early Warning) and Industrial Subsurface Development (e.g. drilling for oil). These use-cases seem to be quite different at first sight but share a lot of similarities, like managing and looking up available sensors, extracting data from them and annotate it semantically, intelligently manage the data (big data problem), run mathematical analysis algorithms on the data and finally provide decision support on this basis. The main challenge was to create a generic architecture which fits both use-cases. The requirements to the architecture are manifold and the whole spectrum of a modern, geo-distributed and collaborative system comes into play. Obviously, one cannot expect to tackle these challenges adequately with a monolithic system or with a single technology. Therefore, a system architecture providing the blueprints to implement the system-of-systems approach has to combine multiple technologies and architectural styles. The most important architectural challenges we needed to address are 1. Build a scalable communication layer for a System-of-sytems 2. Build a resilient communication layer for a System-of-sytems 3. Efficiently publish large volumes of semantically rich sensor data 4. Scalable and high performance storage of large distributed datasets 5. Handling federated multi-domain heterogeneous data 6. Discovery of resources in a geo-distributed SoS 7. Coordination of work between geo-distributed systems The design decisions made for each of them will be presented. These developed concepts are also applicable to the requirements of the Future Internet (FI) and Internet of Things (IoT) which will provide services like smart grids, smart metering, logistics and

  19. Early Period of Modern Architecture in Turkey - A Case Study of Eskisehir

    Science.gov (United States)

    Karasozen, Rana

    2017-10-01

    Modern architecture in the Western World bore fruit at the beginning of the 20th Century in consequence of the process of modernity and seeking of the proper architecture for it. It was formed firstly towards the end of the 1920s. The main reason of this nonsynchronous development was the inadequacy of enlightenment and industrial revolution during the Ottoman Empire and the lack of formation of an intellectual infrastructure which provides the basis of modernity. However, the Ottoman Westernization occurring in the 19th century constituted the foundations of the Republic modernity founded in 1923. The earliest modern architectural designs in Turkey were first practised by European architects after the foundation of the Republic and internalised and practised extensively by the native architects afterwards. The early modern architecture of Turkey, named as “1930s Modernism”, continued until the beginning of the World War II. This period was formed in between the periods of first and second nationalist architecture movements. The early modern architecture period of Turkey was a period which high-quality designs were made. It was practised and internalised not only in big cities such as Ankara and in Istanbul, but also in the medium and small cities of the country. This situation was not just about a formal exception but about the internalisation of modernity by the society. Eskisehir is one of the most important pioneering cities of the Republic period in terms of industrial and educational developments. The earliest modern buildings were built as the public buildings by the state and non-citizen architects in the inadequate conditions of the country in terms of economy and professional people. The earliest modern houses of the city designed by these architects were the prototypes for the later practices which offered the citizens a new lifestyle. The modern houses were the symbols of prestige and status for the owners and the dwellers. The features of early

  20. Consumer adoption and grid impact models for plug-in hybrid electric vehicles in Wisconsin.

    Science.gov (United States)

    2010-05-01

    This proposed study focuses on assessing the demand for plug-in hybrid electric vehicles (PHEV) in Wisconsin and its economic : impacts on the States energy market and the electric grid. PHEVs are expected to provide a range of about 40 miles per ...

  1. An Open Source-Based Real-Time Data Processing Architecture Framework for Manufacturing Sustainability

    Directory of Open Access Journals (Sweden)

    Muhammad Syafrudin

    2017-11-01

    Full Text Available Currently, the manufacturing industry is experiencing a data-driven revolution. There are multiple processes in the manufacturing industry and will eventually generate a large amount of data. Collecting, analyzing and storing a large amount of data are one of key elements of the smart manufacturing industry. To ensure that all processes within the manufacturing industry are functioning smoothly, the big data processing is needed. Thus, in this study an open source-based real-time data processing (OSRDP architecture framework was proposed. OSRDP architecture framework consists of several open sources technologies, including Apache Kafka, Apache Storm and NoSQL MongoDB that are effective and cost efficient for real-time data processing. Several experiments and impact analysis for manufacturing sustainability are provided. The results showed that the proposed system is capable of processing a massive sensor data efficiently when the number of sensors data and devices increases. In addition, the data mining based on Random Forest is presented to predict the quality of products given the sensor data as the input. The Random Forest successfully classifies the defect and non-defect products, and generates high accuracy compared to other data mining algorithms. This study is expected to support the management in their decision-making for product quality inspection and support manufacturing sustainability.

  2. Industrial Robot Programming and UPnP Services Orchestration for the Automation of Factories

    Directory of Open Access Journals (Sweden)

    A. Valera

    2012-10-01

    Full Text Available The integration of equipment and other devices built into industrial robot cells with modern Ethernet interface technologies and low-cost mass produced devices (such as vision systems, laser scanners, force torque-sensors, PLCs and PDAs etc. enables integrators to offer more powerful and smarter solutions. Nevertheless, the programming of all these devices efficiently requires very specific knowledge about them, such as their hardware architectures and specific programming languages as well as details about the system's low level communication protocols. To address these issues, this paper describes and analyses the Plug-and-Play architecture. This is one of the most interesting service-oriented architectures (SOAs available, which exhibits characteristics that are well adapted to industrial robotics cells. To validate their programming features and applicability, a test bed was specially designed. This provides a new graphical service orchestration which was implemented using Workflow Foundation 4 of .NET. The obtained results allowed us to verify that the use of integration schemes based on SOAs reduces the system integration time and is better adapted to industrial robotic cell system integrators.

  3. Personality Characteristics and Level of Performance of Male County Extension Agents in Wisconsin.

    Science.gov (United States)

    Pandya, Dasharathrai Navnitrai

    The major purpose of this study was to determine the relationship between selected personality characteristics and attitudes of male extension agents in Wisconsin, and their level of job performance. The relationships between selected background factors and the level of agent's job performance were also studied. Subjects were 79 male county agents…

  4. Legislation on Homelessness. Wisconsin Legislative Council Report No. 12 to the 1991 Legislature.

    Science.gov (United States)

    Rose, Laura; Matthias, Mary

    The components of Wisconsin's 1991 Assembly Bill 680 that considers homelessness are discussed in this document. The Bill itself addresses: (1) surplus state lands; (2) transitional housing grants; (3) prevention of homelessness; (4) establishing a low-income housing income and franchise tax credit; (5) veterans lacking a permanent address; (6)…

  5. Self Perceived Leadership Styles of Male and Female Superintendents in Wisconsin Public Schools

    Science.gov (United States)

    Rieckmann, Kelly Renée

    2016-01-01

    The number of female superintendents in Wisconsin public schools remains disproportionately low compared to males. With research supporting a connection between female leaders and transformational leadership, the question as to why more females do not enter the realm of leadership and how they see themselves as leaders remains unanswered. This…

  6. A Study Effects Architectural Marketing Capabilities on Performance Marketing unit Based on: Morgan et al case: Past Industry in Tehran

    OpenAIRE

    Mohammad Reza Dalvi; Robabe Seifi

    2014-01-01

    Over a period of time architectural marketing capabilities combination of knowledge and skills develop in to capabilities. These architectural marketing capabilities have been identified as one of the important ways firms can achieve a competitive advantage The following research tests effects architectural marketing capabilities on performance marketing unit Based on a survey .a structural equation model was developed to test our hypotheses. the study develops a structural model linking arch...

  7. Capital Architecture: Situating symbolism parallel to architectural methods and technology

    Science.gov (United States)

    Daoud, Bassam

    Capital Architecture is a symbol of a nation's global presence and the cultural and social focal point of its inhabitants. Since the advent of High-Modernism in Western cities, and subsequently decolonised capitals, civic architecture no longer seems to be strictly grounded in the philosophy that national buildings shape the legacy of government and the way a nation is regarded through its built environment. Amidst an exceedingly globalized architectural practice and with the growing concern of key heritage foundations over the shortcomings of international modernism in representing its immediate socio-cultural context, the contextualization of public architecture within its sociological, cultural and economic framework in capital cities became the key denominator of this thesis. Civic architecture in capital cities is essential to confront the challenges of symbolizing a nation and demonstrating the legitimacy of the government'. In today's dominantly secular Western societies, governmental architecture, especially where the seat of political power lies, is the ultimate form of architectural expression in conveying a sense of identity and underlining a nation's status. Departing with these convictions, this thesis investigates the embodied symbolic power, the representative capacity, and the inherent permanence in contemporary architecture, and in its modes of production. Through a vast study on Modern architectural ideals and heritage -- in parallel to methodologies -- the thesis stimulates the future of large scale governmental building practices and aims to identify and index the key constituents that may respond to the lack representation in civic architecture in capital cities.

  8. Software architecture evolution

    DEFF Research Database (Denmark)

    Barais, Olivier; Le Meur, Anne-Francoise; Duchien, Laurence

    2008-01-01

    Software architectures must frequently evolve to cope with changing requirements, and this evolution often implies integrating new concerns. Unfortunately, when the new concerns are crosscutting, existing architecture description languages provide little or no support for this kind of evolution....... The software architect must modify multiple elements of the architecture manually, which risks introducing inconsistencies. This chapter provides an overview, comparison and detailed treatment of the various state-of-the-art approaches to describing and evolving software architectures. Furthermore, we discuss...... one particular framework named Tran SAT, which addresses the above problems of software architecture evolution. Tran SAT provides a new element in the software architecture descriptions language, called an architectural aspect, for describing new concerns and their integration into an existing...

  9. Experimental Demonstration of a Self-organized Architecture for Emerging Grid Computing Applications on OBS Testbed

    Science.gov (United States)

    Liu, Lei; Hong, Xiaobin; Wu, Jian; Lin, Jintong

    As Grid computing continues to gain popularity in the industry and research community, it also attracts more attention from the customer level. The large number of users and high frequency of job requests in the consumer market make it challenging. Clearly, all the current Client/Server(C/S)-based architecture will become unfeasible for supporting large-scale Grid applications due to its poor scalability and poor fault-tolerance. In this paper, based on our previous works [1, 2], a novel self-organized architecture to realize a highly scalable and flexible platform for Grids is proposed. Experimental results show that this architecture is suitable and efficient for consumer-oriented Grids.

  10. Architectural design decisions

    NARCIS (Netherlands)

    Jansen, Antonius Gradus Johannes

    2008-01-01

    A software architecture can be considered as the collection of key decisions concerning the design of the software of a system. Knowledge about this design, i.e. architectural knowledge, is key for understanding a software architecture and thus the software itself. Architectural knowledge is mostly

  11. Satellite ATM Networks: Architectures and Guidelines Developed

    Science.gov (United States)

    vonDeak, Thomas C.; Yegendu, Ferit

    1999-01-01

    An important element of satellite-supported asynchronous transfer mode (ATM) networking will involve support for the routing and rerouting of active connections. Work published under the auspices of the Telecommunications Industry Association (http://www.tiaonline.org), describes basic architectures and routing protocol issues for satellite ATM (SATATM) networks. The architectures and issues identified will serve as a basis for further development of technical specifications for these SATATM networks. Three ATM network architectures for bent pipe satellites and three ATM network architectures for satellites with onboard ATM switches were developed. The architectures differ from one another in terms of required level of mobility, supported data rates, supported terrestrial interfaces, and onboard processing and switching requirements. The documentation addresses low-, middle-, and geosynchronous-Earth-orbit satellite configurations. The satellite environment may require real-time routing to support the mobility of end devices and nodes of the ATM network itself. This requires the network to be able to reroute active circuits in real time. In addition to supporting mobility, rerouting can also be used to (1) optimize network routing, (2) respond to changing quality-of-service requirements, and (3) provide a fault tolerance mechanism. Traffic management and control functions are necessary in ATM to ensure that the quality-of-service requirements associated with each connection are not violated and also to provide flow and congestion control functions. Functions related to traffic management were identified and described. Most of these traffic management functions will be supported by on-ground ATM switches, but in a hybrid terrestrial-satellite ATM network, some of the traffic management functions may have to be supported by the onboard satellite ATM switch. Future work is planned to examine the tradeoffs of placing traffic management functions onboard a satellite as

  12. Educational strategies for architectural design management : the design of a new curriculum

    NARCIS (Netherlands)

    Prins, M.; Halman, J.I.M.

    1996-01-01

    This paper is about the design of a new curriculum on Architectural Design Management Systems. This curriculum is embedded in the Stan Ackermans lnstitute(SAI). The SAI is a school for continuing post graduate education on technological design. First some recent developments in the building industry

  13. Status, Vision, and Challenges of an Intelligent Distributed Engine Control Architecture

    Science.gov (United States)

    Behbahani, Alireza; Culley, Dennis; Garg, Sanjay; Millar, Richard; Smith, Bert; Wood, Jim; Mahoney, Tim; Quinn, Ronald; Carpenter, Sheldon; Mailander, Bill; hide

    2007-01-01

    A Distributed Engine Control Working Group (DECWG) consisting of the Department of Defense (DoD), the National Aeronautics and Space Administration (NASA) Glenn Research Center (GRC) and industry has been formed to examine the current and future requirements of propulsion engine systems. The scope of this study will include an assessment of the paradigm shift from centralized engine control architecture to an architecture based on distributed control utilizing open system standards. Included will be a description of the work begun in the 1990's, which continues today, followed by the identification of the remaining technical challenges which present barriers to on-engine distributed control.

  14. Cloud-based multi-agent architecture for effective planning and scheduling of distributed manufacturing

    DEFF Research Database (Denmark)

    Mishra, Nishikant; Singh, Akshit; Kumari, Sushma

    2016-01-01

    at distinct locations are being assembled in a plant to develop the final product. In this complex scenario, manufacturing firms have to be responsive enough to cope with the fluctuating demand of customers. To accomplish it, there is a need to develop an integrated, dynamic and autonomous system....... In this article, a self-reactive cloud-based multi-agent architecture for distributed manufacturing system is developed. The proposed architecture will assist manufacturing industry to establish real-time information exchange between the autonomous agents, clients, suppliers and manufacturing unit. The mechanism...

  15. Architecture Governance: The Importance of Architecture Governance for Achieving Operationally Responsive Ground Systems

    Science.gov (United States)

    Kolar, Mike; Estefan, Jeff; Giovannoni, Brian; Barkley, Erik

    2011-01-01

    Topics covered (1) Why Governance and Why Now? (2) Characteristics of Architecture Governance (3) Strategic Elements (3a) Architectural Principles (3b) Architecture Board (3c) Architecture Compliance (4) Architecture Governance Infusion Process. Governance is concerned with decision making (i.e., setting directions, establishing standards and principles, and prioritizing investments). Architecture governance is the practice and orientation by which enterprise architectures and other architectures are managed and controlled at an enterprise-wide level

  16. Convective cells and their relationship to vortex diffusion in the Wisconsin Levitated Octupole

    International Nuclear Information System (INIS)

    Ehrhardt, A.B.

    1978-01-01

    The purpose of this thesis is two-fold: first, to present floating potential structure for different plasmas and operating parameters in the Wisconsin Levitated Octupole. Second, to show how the observed potential structure can be used, within the framework of vortex diffusion, to account for enhanced diffusion in the appropriate parameter regimes

  17. Minimalism in architecture: Architecture as a language of its identity

    Directory of Open Access Journals (Sweden)

    Vasilski Dragana

    2012-01-01

    Full Text Available Every architectural work is created on the principle that includes the meaning, and then this work is read like an artifact of the particular meaning. Resources by which the meaning is built primarily, susceptible to transformation, as well as routing of understanding (decoding messages carried by a work of architecture, are subject of semiotics and communication theories, which have played significant role for the architecture and the architect. Minimalism in architecture, as a paradigm of the XXI century architecture, means searching for essence located in the irreducible minimum. Inspired use of architectural units (archetypical elements, trough the fatasm of simplicity, assumes the primary responsibility for providing the object identity, because it participates in language formation and therefore in its reading. Volume is form by clean language that builds the expression of the fluid areas liberated of recharge needs. Reduced architectural language is appropriating to the age marked by electronic communications.

  18. Modular Integrated Monitoring System (MIMS). Architecture and implementation

    International Nuclear Information System (INIS)

    Funkhouser, D.R.; Davidson, G.W.; Deland, S.M.

    1999-01-01

    The MIMS is being developed as a cost-effective means of performing safeguards in unattended remote monitoring applications. Based on industry standards and an open systems approach, the MIMS architecture supports both data acquisition and data review subsystems. Data includes images as well as discrete and analog sensor outputs. The MIMS uses an Echelon LonWorks network as a standard means and method of data acquisition from the sensor. A common data base not only stores sensor and image data but also provides a structure by which dynamic changes to the sensor system can be reflected in the data acquisition and data review subsystems without affecting the execution software. The architecture includes standards for wide area communications between data acquisition systems and data review systems. Data authentication is provided as an integral part of the design. The MIMS also provides a generic set of tools for analyzing both system behavior and observed events. The MIMS software implements this architecture by combining the use of commercial applications with a set of custom 16 and 32 bit Microsoft Windows applications which are run under Windows NT and Windows 95 operating systems. (author)

  19. Wisconsin torsatron/stellarator program, FY 1989

    International Nuclear Information System (INIS)

    Shohet, J.L.; Anderson, D.T.; Anderson, F.S.B.; Talmadge, J.N.

    1988-07-01

    This proposal documents recent activities within the University of Wisconsin-Madison Torsatron/Stellarator Laboratory and presents plans for future research activities for a three year period. Research efforts have focused on fundamental stellarator physics issues through experimental investigations on the Interchangeable Module Stellarator (IMS) and the Proto-Cleo Stellarator. Theoretical activities and studies of new configurations are being undertaken to support and broaden the experimental program. Experimental research at the Torsatron Stellarator Laboratory has been primarily concerned with effects induced through electron-cyclotron resonant frequency plasma production and heating in the IMS device. Plasma electric fields have been shown to play a major role in particle transport and confinement in IMS. ECRF heating at 6 kG has produced electron tail populations in agreement with Monte-Carlo models. Electric and magnetic fields have been shown to alter the particle flows to the IMS modular divertors. 48 refs

  20. Architectural Narratives

    DEFF Research Database (Denmark)

    Kiib, Hans

    2010-01-01

    a functional framework for these concepts, but tries increasingly to endow the main idea of the cultural project with a spatially aesthetic expression - a shift towards “experience architecture.” A great number of these projects typically recycle and reinterpret narratives related to historical buildings......In this essay, I focus on the combination of programs and the architecture of cultural projects that have emerged within the last few years. These projects are characterized as “hybrid cultural projects,” because they intend to combine experience with entertainment, play, and learning. This essay...... and architectural heritage; another group tries to embed new performative technologies in expressive architectural representation. Finally, this essay provides a theoretical framework for the analysis of the political rationales of these projects and for the architectural representation bridges the gap between...

  1. Climate change science applications and needs in forest ecosystem management: a workshop organized as part of the northern Wisconsin Climate Change Response Framework Project

    Science.gov (United States)

    Leslie Brandt; Chris Swanston; Linda Parker; Maria Janowiak; Richard Birdsey; Louis Iverson; David Mladenoff; Patricia. Butler

    2012-01-01

    Climate change is leading to direct and indirect impacts on forest tree species and ecosystems in northern Wisconsin. Land managers will need to prepare for and respond to these impacts, so we designed a workshop to identify forest management approaches that can enhance the ability of ecosystems in northern Wisconsin to cope with climate change and address how National...

  2. Population Characteristics of Drunk Drivers Referred for Assessment in Two Wisconsin Counties 1981-1983.

    Science.gov (United States)

    Gurnack, Anne M.

    1986-01-01

    Summarizes a study of Wisconsin's drunk driving law and evaluates the mandated alcohol assessment for convicted offenders. Findings indicated individuals operating while intoxicated remain young, male, unmarried, with high school educations. A substantial number of these persons were assessed with serious drinking problems. The strongest predictor…

  3. Architecture & Environment

    Science.gov (United States)

    Erickson, Mary; Delahunt, Michael

    2010-01-01

    Most art teachers would agree that architecture is an important form of visual art, but they do not always include it in their curriculums. In this article, the authors share core ideas from "Architecture and Environment," a teaching resource that they developed out of a long-term interest in teaching architecture and their fascination with the…

  4. Exporting Humanist Architecture

    DEFF Research Database (Denmark)

    Nielsen, Tom

    2016-01-01

    The article is a chapter in the catalogue for the Danish exhibition at the 2016 Architecture Biennale in Venice. The catalogue is conceived at an independent book exploring the theme Art of Many - The Right to Space. The chapter is an essay in this anthology tracing and discussing the different...... values and ethical stands involved in the export of Danish Architecture. Abstract: Danish architecture has, in a sense, been driven by an unwritten contract between the architects and the democratic state and its institutions. This contract may be viewed as an ethos – an architectural tradition...... with inherent aesthetic and moral values. Today, however, Danish architecture is also an export commodity. That raises questions, which should be debated as openly as possible. What does it mean for architecture and architects to practice in cultures and under political systems that do not use architecture...

  5. Groundwater Quantity and Quality Issues in a Water-Rich Region: Examples from Wisconsin, USA

    Directory of Open Access Journals (Sweden)

    John Luczaj

    2015-06-01

    Full Text Available The State of Wisconsin is located in an unusually water-rich portion of the world in the western part of the Great Lakes region of North America. This article presents an overview of the major groundwater quantity and quality concerns for this region in a geologic context. The water quantity concerns are most prominent in the central sand plain region and portions of a Paleozoic confined sandstone aquifer in eastern Wisconsin. Water quality concerns are more varied, with significant impacts from both naturally occurring inorganic contaminants and anthropogenic sources. Naturally occurring contaminants include radium, arsenic and associated heavy metals, fluoride, strontium, and others. Anthropogenic contaminants include nitrate, bacteria, viruses, as well as endocrine disrupting compounds. Groundwater quality in the region is highly dependent upon local geology and land use, but water bearing geologic units of all ages, Precambrian through Quaternary, are impacted by at least one kind of contaminant.

  6. Grid-based Simulation of Industrial Thin Film Production

    NARCIS (Netherlands)

    Krzhizhanovskaya, V.V.; Sloot, P.M.A.; Gorbachev, Y.E.

    2005-01-01

    In this article, the authors introduce a Grid-based virtual reactor, a High Level Architecture (HLA)-supported problem-solving environment that allows for detailed numerical study of industrial thin-film production in plasma-enhanced chemical vapor deposition (PECVD) reactors. They briefly describe

  7. Fragments of Architecture

    DEFF Research Database (Denmark)

    Bang, Jacob Sebastian

    2016-01-01

    Topic 3: “Case studies dealing with the artistic and architectural work of architects worldwide, and the ties between specific artistic and architectural projects, methodologies and products”......Topic 3: “Case studies dealing with the artistic and architectural work of architects worldwide, and the ties between specific artistic and architectural projects, methodologies and products”...

  8. Promoting Success in the Physical Sciences: The University of Wisconsin's Physics Learning Program

    Science.gov (United States)

    Nossal, S. M.; Jacob, A. T.

    2002-05-01

    The Physics Learning Program at the University of Wisconsin-Madison provides small group, academic and mentoring support for students enrolled in algebra-based introductory physics courses. Those students accepted into our program are potentially at-risk academically in their physics course or for feeling isolated at the University. They include, among others, students who have not taken high school physics, returning adults, minority students, students with disabilities, and students with English as a second language. A core component of the program is the peer-lead teaching and mentoring groups that match upper level undergraduate physics majors with students potentially at-risk in introductory physics. The tutors receive ongoing training and supervision throughout the year. The program has expanded over the years to include staff tutors, the majority of whom are scientists who seek additional teaching experience. The Physics Peer Mentor Tutor Program is run in collaboration with a similar chemistry program at the University of Wisconsin's Chemistry Learning Center. We will describe our Physics Learning Programs and discuss some of the challenges, successes, and strategies used to work with our tutors and students.

  9. Interfacing industrial process control systems to LEP/LHC

    International Nuclear Information System (INIS)

    Rabany, M.

    1992-01-01

    Modern industrial process control systems have developed to meet the needs of industry to increase the production while decreasing the costs. Although particle accelerators designers have pioneered in control systems during the seventies, it has now become possible to them to profit of industrial solutions in substitution of, or in complement with the more traditional home made ones. Adapting and integrating such industrial systems to the accelerator control area will certainly benefit to the field in terms of finance, human resources and technical facilities offered off-the-shelf by the widely experienced industrial controls community; however this cannot be done without slightly affecting the overall accelerator control architecture. The paper briefly describes the industrial controls arena and takes example on an industrial process control system recently installed at CERN to discuss in detail the related choices and issues. (author)

  10. Enterprise architecture management

    DEFF Research Database (Denmark)

    Rahimi, Fatemeh; Gøtze, John; Møller, Charles

    2017-01-01

    Despite the growing interest in enterprise architecture management, researchers and practitioners lack a shared understanding of its applications in organizations. Building on findings from a literature review and eight case studies, we develop a taxonomy that categorizes applications of enterprise...... architecture management based on three classes of enterprise architecture scope. Organizations may adopt enterprise architecture management to help form, plan, and implement IT strategies; help plan and implement business strategies; or to further complement the business strategy-formation process....... The findings challenge the traditional IT-centric view of enterprise architecture management application and suggest enterprise architecture management as an approach that could support the consistent design and evolution of an organization as a whole....

  11. Enterprise architecture management

    DEFF Research Database (Denmark)

    Rahimi, Fatemeh; Gøtze, John; Møller, Charles

    2017-01-01

    architecture management based on three classes of enterprise architecture scope. Organizations may adopt enterprise architecture management to help form, plan, and implement IT strategies; help plan and implement business strategies; or to further complement the business strategy-formation process......Despite the growing interest in enterprise architecture management, researchers and practitioners lack a shared understanding of its applications in organizations. Building on findings from a literature review and eight case studies, we develop a taxonomy that categorizes applications of enterprise....... The findings challenge the traditional IT-centric view of enterprise architecture management application and suggest enterprise architecture management as an approach that could support the consistent design and evolution of an organization as a whole....

  12. Using the Wisconsin-Ohio Reference Evaluation Program (WOREP) to Improve Training and Reference Services

    Science.gov (United States)

    Novotny, Eric; Rimland, Emily

    2007-01-01

    This article discusses a service quality study conducted in the Pennsylvania State University Libraries. The Wisconsin-Ohio Reference Evaluation Program survey was selected as a valid, standardized instrument. We present our results, highlighting the impact on reference training. A second survey a year later demonstrated that focusing on…

  13. Service oriented architecture for clinical decision support: a systematic review and future directions.

    Science.gov (United States)

    Loya, Salvador Rodriguez; Kawamoto, Kensaku; Chatwin, Chris; Huser, Vojtech

    2014-12-01

    The use of a service-oriented architecture (SOA) has been identified as a promising approach for improving health care by facilitating reliable clinical decision support (CDS). A review of the literature through October 2013 identified 44 articles on this topic. The review suggests that SOA related technologies such as Business Process Model and Notation (BPMN) and Service Component Architecture (SCA) have not been generally adopted to impact health IT systems' performance for better care solutions. Additionally, technologies such as Enterprise Service Bus (ESB) and architectural approaches like Service Choreography have not been generally exploited among researchers and developers. Based on the experience of other industries and our observation of the evolution of SOA, we found that the greater use of these approaches have the potential to significantly impact SOA implementations for CDS.

  14. Valuable Work, Minimal Rewards: A Report on the Wisconsin Child Care Work Force.

    Science.gov (United States)

    Burton, Alice; And Others

    A 1994 state-wide survey examined the status of child care profession in Wisconsin. Surveyed were 326 family child care providers, 104 child care center directors, and 254 center teaching staff. Responses indicated that child care teaching staff have experienced a wage increase of just over 1 percent per year since 1988, and continue to earn low…

  15. Virtual Enterprise Reference Architecture and Methodology (VERAM), Joint D41/D43 deliverable of GLOBEMEN

    DEFF Research Database (Denmark)

    Tølle, Martin; Zwegers, Arian; Vesterager, Johan

    2003-01-01

    . IMS Globemen is an inter-regional project aiming to develop methods, tools and architectures to support inter-enterprise operations in one-of-kind industries, in different lifecycle phases. This deliverable describes an architectural framework VERAM including a description/elaboration of its elements......-of-a-kind-production”, the concept of the Virtual Enterprise (VE) and the Virtual Enterprise Reference Architecture (VERA) developed in GLOBEMEN. - In Chapter 4 a so-called life history example is presented to give a possible scenario about how an enterprise network could evolve over time, and to point out the need for preparing...... and setting up networks and VEs. The life history example in Chapter 4 highlights the potential for preparing and reusing existing knowledge related to enterprise networks and VEs. - As a means to structure relevant knowledge GLOBEMEN developed the VERAM (Virtual Enterprise Reference Architecture...

  16. Modeling Architectural Patterns’ Behavior Using Architectural Primitives

    NARCIS (Netherlands)

    Waqas Kamal, Ahmad; Avgeriou, Paris

    2008-01-01

    Architectural patterns have an impact on both the structure and the behavior of a system at the architecture design level. However, it is challenging to model patterns’ behavior in a systematic way because modeling languages do not provide the appropriate abstractions and because each pattern

  17. Understanding Enterprise Architecture with Topic Modeling Preliminary Research Based on Journal Articles

    DEFF Research Database (Denmark)

    Nardello, Marco; Møller, Charles; Gøtze, John

    2018-01-01

    The next 3 years will be more important than the last 50 due to the digital transformation across industries. Enterprise Architecture (EA), the discipline that should lead enterprise responses to disruptive forces, is far from ready to drive the next wave of change. The state of the art in the di...

  18. Merging Agents and Cloud Services in Industrial Applications

    OpenAIRE

    Francisco P. Maturana; Juan L. Asenjo; Neethu S. Philip; Shweta Chatrola

    2014-01-01

    A novel idea to combine agent technology and cloud computing for monitoring a plant floor system is presented. Cloud infrastructure has been leveraged as the main mechanism for hosting the data and processing needs of a modern industrial information system. The cloud offers unlimited storage and data processing in a near real-time fashion. This paper presents a software-as-a-service (SaaS) architecture for augmenting industrial plant-floor reporting capabilities. This reporting capability has...

  19. Space and Architecture's Current Line of Research? A Lunar Architecture Workshop With An Architectural Agenda.

    Science.gov (United States)

    Solomon, D.; van Dijk, A.

    The "2002 ESA Lunar Architecture Workshop" (June 3-16) ESTEC, Noordwijk, NL and V2_Lab, Rotterdam, NL) is the first-of-its-kind workshop for exploring the design of extra-terrestrial (infra) structures for human exploration of the Moon and Earth-like planets introducing 'architecture's current line of research', and adopting an architec- tural criteria. The workshop intends to inspire, engage and challenge 30-40 European masters students from the fields of aerospace engineering, civil engineering, archi- tecture, and art to design, validate and build models of (infra) structures for Lunar exploration. The workshop also aims to open up new physical and conceptual terrain for an architectural agenda within the field of space exploration. A sound introduc- tion to the issues, conditions, resources, technologies, and architectural strategies will initiate the workshop participants into the context of lunar architecture scenarios. In my paper and presentation about the development of the ideology behind this work- shop, I will comment on the following questions: * Can the contemporary architectural agenda offer solutions that affect the scope of space exploration? It certainly has had an impression on urbanization and colonization of previously sparsely populated parts of Earth. * Does the current line of research in architecture offer any useful strategies for com- bining scientific interests, commercial opportunity, and public space? What can be learned from 'state of the art' architecture that blends commercial and public pro- grammes within one location? * Should commercial 'colonisation' projects in space be required to provide public space in a location where all humans present are likely to be there in a commercial context? Is the wave in Koolhaas' new Prada flagship store just a gesture to public space, or does this new concept in architecture and shopping evolve the public space? * What can we learn about designing (infra-) structures on the Moon or any other

  20. IT Security Aspects of Industrial Control Systems

    Directory of Open Access Journals (Sweden)

    Peter Holecko

    2006-01-01

    Full Text Available This paper discusses a set of general network system architectures for industrial process control systems as well as vulnerabilities related to these systems and the IT threats these systems are exposed to from the point of view of Common Criteria methodology and ITU-T recommendation X.805.

  1. Methodical Design of Software Architecture Using an Architecture Design Assistant (ArchE)

    Science.gov (United States)

    2005-04-01

    PA 15213-3890 Methodical Design of Software Architecture Using an Architecture Design Assistant (ArchE) Felix Bachmann and Mark Klein Software...DATES COVERED 00-00-2005 to 00-00-2005 4. TITLE AND SUBTITLE Methodical Design of Software Architecture Using an Architecture Design Assistant...important for architecture design – quality requirements and constraints are most important Here’s some evidence: If the only concern is

  2. Agent-Oriented Privacy-Based Information Brokering Architecture for Healthcare Environments

    Directory of Open Access Journals (Sweden)

    Abdulmutalib Masaud-Wahaishi

    2009-01-01

    Full Text Available Healthcare industry is facing a major reform at all levels—locally, regionally, nationally, and internationally. Healthcare services and systems become very complex and comprise of a vast number of components (software systems, doctors, patients, etc. that are characterized by shared, distributed and heterogeneous information sources with varieties of clinical and other settings. The challenge now faced with decision making, and management of care is to operate effectively in order to meet the information needs of healthcare personnel. Currently, researchers, developers, and systems engineers are working toward achieving better efficiency and quality of service in various sectors of healthcare, such as hospital management, patient care, and treatment. This paper presents a novel information brokering architecture that supports privacy-based information gathering in healthcare. Architecturally, the brokering is viewed as a layer of services where a brokering service is modeled as an agent with a specific architecture and interaction protocol that are appropriate to serve various requests. Within the context of brokering, we model privacy in terms of the entities ability to hide or reveal information related to its identities, requests, and/or capabilities. A prototype of the proposed architecture has been implemented to support information-gathering capabilities in healthcare environments using FIPA-complaint platform JADE.

  3. Agent-oriented privacy-based information brokering architecture for healthcare environments.

    Science.gov (United States)

    Masaud-Wahaishi, Abdulmutalib; Ghenniwa, Hamada

    2009-01-01

    Healthcare industry is facing a major reform at all levels-locally, regionally, nationally, and internationally. Healthcare services and systems become very complex and comprise of a vast number of components (software systems, doctors, patients, etc.) that are characterized by shared, distributed and heterogeneous information sources with varieties of clinical and other settings. The challenge now faced with decision making, and management of care is to operate effectively in order to meet the information needs of healthcare personnel. Currently, researchers, developers, and systems engineers are working toward achieving better efficiency and quality of service in various sectors of healthcare, such as hospital management, patient care, and treatment. This paper presents a novel information brokering architecture that supports privacy-based information gathering in healthcare. Architecturally, the brokering is viewed as a layer of services where a brokering service is modeled as an agent with a specific architecture and interaction protocol that are appropriate to serve various requests. Within the context of brokering, we model privacy in terms of the entities ability to hide or reveal information related to its identities, requests, and/or capabilities. A prototype of the proposed architecture has been implemented to support information-gathering capabilities in healthcare environments using FIPA-complaint platform JADE.

  4. A Descriptive Study of Wisconsin PK-12 Virtual Public School Program Operations and Management

    Science.gov (United States)

    Banker, Margaret M.

    2012-01-01

    E-Learning as it pertains to public education is in its infancy in America. There is limited research on what operational design, development, and management attributes of virtual school programs foster student achievement. The Wisconsin Department of Instruction has not developed or adopted program standards for E-Learning programs. The purpose…

  5. 2 Dailies Battle for Readers and Advertisers in U. of Wisconsin Student-Newspaper War.

    Science.gov (United States)

    Hirschorn, Michael W.

    1987-01-01

    Two student newspapers at the University of Wisconsin at Madison are in fierce competition for readers and advertisers. A proposal of the Badger Herald, an 18-year-old conservative weekly, that the two merge their financial operations was rejected by the liberal Daily Cardinal and the newspaper war was on. (MLW)

  6. Waste Management in Universities and Colleges. Workshop Proceedings (Madison, Wisconsin, July 9-11, 1980).

    Science.gov (United States)

    Association of Physical Plant Administrators of Universities and Colleges, Washington, DC.

    In response to a request from the Wisconsin Department of Natural Resources, Region V of the United States Environmental Protection Agency (EPA) sponsored a workshop on waste management in universities and colleges. It consisted of four sessions: (1) managing general university waste and regulatory concerns; (2) chemical waste management; (3)…

  7. A study of space station needs, attributes and architectural options, volume 2, technical. Book 3: Economic benefits, costs and programmatics

    Science.gov (United States)

    1983-01-01

    The economic benefits, cost analysis, and industrial uses of the manned space station are investigated. Mission payload costs are examined in relation to alternative architectures and projected technological evolution. Various approaches to industrial involvement for financing, development, and marketing of space station resources are described.

  8. BIM Investment, Returns, and Risks in China’s AEC Industries

    OpenAIRE

    Jin, R; Hancock, CM; Tang, L; Wanatowski, D

    2017-01-01

    Building information modeling (BIM), the emerging digital technology, is undergoing increasing application in developing countries including China. Both the governmental policy and industry motivation have indicated that BIM is becoming the mainstream innovation in China’s construction industry. Nevertheless, one major concern lies in the uncertainty of BIM investment for architecture, engineering, and construction (AEC) firms. Specifically, AEC firms should have the knowledge of areas BIM in...

  9. Adaptables in the post-industrial society

    DEFF Research Database (Denmark)

    Stylsvig Madsen, Ulrik

    2006-01-01

    How can contemporary industrialized production meet the requirements of a growing complexity and dynamism in a global society? In a society affected by globalization and the never-ending flow of information, the need for artefacts to reinforce the identity of organizations and individuals...... is growing. The mission of architecture is then to form a framework of identity for the particular function or individual, a framework capable of distinguishing the function / the individual from one another and from the surrounding society. Industrial production within the construction business is therefore...... met with increasing demands for individual solutions. The question then is how this challenge is met in the best way by industrialized production, technologically (products/solutions) as well as theoretically (conceptual approach)...

  10. Preemptive Architecture: Explosive Art and Future Architectures in Cursed Urban Zones

    Directory of Open Access Journals (Sweden)

    Stahl Stenslie

    2017-04-01

    Full Text Available This article describes the art and architectural research project Preemptive Architecture that uses artistic strategies and approaches to create bomb-ready architectural structures that act as instruments for the undoing of violence in war. Increasing environmental usability through destruction represents an inverse strategy that reverses common thinking patterns about warfare, art and architecture. Building structures predestined for a construc­tive destruction becomes a creative act. One of the main motivations behind this paper is to challenge and expand the material thinking as well as the socio-political conditions related to artistic, architectural and design based practices.   Article received: December 12, 2016; Article accepted: January 10, 2017; Published online: April 20, 2017 Original scholarly paper How to cite this article: Stenslie, Stahl, and Magne Wiggen. "Preemptive Architecture: Explosive Art and Future Architectures in Cursed Urban Zones." AM Journal of Art and Media Studies 12 (2017: 29-39. doi: 10.25038/am.v0i12.165

  11. Plug-and-play monitoring and performance optimization for industrial automation processes

    CERN Document Server

    Luo, Hao

    2017-01-01

    Dr.-Ing. Hao Luo demonstrates the developments of advanced plug-and-play (PnP) process monitoring and control systems for industrial automation processes. With aid of the so-called Youla parameterization, a novel PnP process monitoring and control architecture (PnP-PMCA) with modularized components is proposed. To validate the developments, a case study on an industrial rolling mill benchmark is performed, and the real-time implementation on a laboratory brushless DC motor is presented. Contents PnP Process Monitoring and Control Architecture Real-Time Configuration Techniques for PnP Process Monitoring Real-Time Configuration Techniques for PnP Performance Optimization Benchmark Study and Real-Time Implementation Target Groups Researchers and students of Automation and Control Engineering Practitioners in the area of Industrial and Production Engineering The Author Hao Luo received the Ph.D. degree at the Institute for Automatic Control and Complex Systems (AKS) at the University of Duisburg-Essen, Germany, ...

  12. Enterprise architecture patterns practical solutions for recurring IT-architecture problems

    CERN Document Server

    Perroud, Thierry

    2013-01-01

    Every enterprise architect faces similar problems when designing and governing the enterprise architecture of a medium to large enterprise. Design patterns are a well-established concept in software engineering, used to define universally applicable solution schemes. By applying this approach to enterprise architectures, recurring problems in the design and implementation of enterprise architectures can be solved over all layers, from the business layer to the application and data layer down to the technology layer.Inversini and Perroud describe patterns at the level of enterprise architecture

  13. MUF architecture /art London

    DEFF Research Database (Denmark)

    Svenningsen Kajita, Heidi

    2009-01-01

    Om MUF architecture samt interview med Liza Fior og Katherine Clarke, partnere i muf architecture/art......Om MUF architecture samt interview med Liza Fior og Katherine Clarke, partnere i muf architecture/art...

  14. Power and Aging Characterization of Digital FIR Filters Architectures

    DEFF Research Database (Denmark)

    Calimera, Andrea; Liu, Wei; Macii, Enrico

    2012-01-01

    -variation, temperature and aging induced variations pose new challenges in the fabrication of the next generation of ICs. This work presents a detailed power and aging characterization of digital FIR filters in an industrial 45nm CMOS technology, and a design space exploration of different filter architectures...... with respect to throughput, area, power dissipation and aging. The exploration is intended to provide new design guidelines when considering aging of components in power/performance tradeoffs....

  15. Digital Architecture – Results From a Gap Analysis

    Energy Technology Data Exchange (ETDEWEB)

    Oxstrand, Johanna Helene [Idaho National Lab. (INL), Idaho Falls, ID (United States); Thomas, Kenneth David [Idaho National Lab. (INL), Idaho Falls, ID (United States); Fitzgerald, Kirk [Idaho National Lab. (INL), Idaho Falls, ID (United States)

    2015-09-01

    The digital architecture is defined as a collection of IT capabilities needed to support and integrate a wide-spectrum of real-time digital capabilities for nuclear power plant performance improvements. The digital architecture can be thought of as an integration of the separate I&C and information systems already in place in NPPs, brought together for the purpose of creating new levels of automation in NPP work activities. In some cases, it might be an extension of the current communication systems, to provide digital communications where they are currently analog only. This collection of IT capabilities must in turn be based on a set of user requirements that must be supported for the interconnected technologies to operate in an integrated manner. These requirements, simply put, are a statement of what sorts of digital work functions will be exercised in a fully-implemented seamless digital environment and how much they will be used. The goal of the digital architecture research is to develop a methodology for mapping nuclear power plant operational and support activities into the digital architecture, which includes the development of a consensus model for advanced information and control architecture. The consensus model should be developed at a level of detail that is useful to the industry. In other words, not so detailed that it specifies specific protocols and not so vague that it is only provides a high level description of technology. The next step towards the model development is to determine the current state of digital architecture at typical NPPs. To investigate the current state, the researchers conducted a gap analysis to determine to what extent the NPPs can support the future digital technology environment with their existing I&C and IT structure, and where gaps exist with respect to the full deployment of technology over time. The methodology, result, and conclusions from the gap analysis are described in this report.

  16. Performance analysis of IMS based LTE and WIMAX integration architectures

    Directory of Open Access Journals (Sweden)

    A. Bagubali

    2016-12-01

    Full Text Available In the current networking field many research works are going on regarding the integration of different wireless technologies, with the aim of providing uninterrupted connectivity to the user anywhere, with high data rates due to increased demand. However, the number of objects like smart devices, industrial machines, smart homes, connected by wireless interface is dramatically increasing due to the evolution of cloud computing and internet of things technology. This Paper begins with the challenges involved in such integrations and then explains the role of different couplings and different architectures. This paper also gives further improvement in the LTE and Wimax integration architectures to provide seamless vertical handover and flexible quality of service for supporting voice, video, multimedia services over IP network and mobility management with the help of IMS networks. Evaluation of various parameters like handover delay, cost of signalling, packet loss,, is done and the performance of the interworking architecture is analysed from the simulation results. Finally, it concludes that the cross layer scenario is better than the non cross layer scenario.

  17. Memory of antiquity and new compatible museum functions Some considerations on the industrial heritage related to electricity production

    Directory of Open Access Journals (Sweden)

    Emanuele Romeo

    2017-12-01

    Full Text Available The industrial heritage is represented by a set of strongly stratified architectural complexes characterized by different technical, formal, and distributive solutions that were gradually added and superimposed to one another, when required by the evolution of technology and by the changes in production processes. Actually, it is this stratification (additions, changes of use, momentary abandonment and subsequent reuse, accompanied by architectural and technological adjustments that gives an industrial complex a particular value.Indeed, the continuous evolution is the essence of this particular architectural form. From the birth of the first factories to present day, the industrial buildings have been able to quickly change their architectural form and their material and formal consistency according for the work and production needs. For this reason, we have now the opportunity to read a "history of architecture" consisting of a sequence of materials and technologies that have been subsequently replaced or superimposed to one another, in a list of examples related to the testing of reinforced concrete, of iron, cast iron, steel; or to the use of large glass surfaces or shed roofs; or to the use of natural and artificial energy sources. Many European experiences of conservation and reuse of industrial buildings have already considered this approach: the choice of the new functions is dictated by the flexibility of the building towards the necessary technical and energy adjustments. This is to achieve a proper balance between respect for the historical memory of the building and the need to adapt to the standards of energy, social and cultural sustainability.

  18. Methods of Data Collection, Sample Processing, and Data Analysis for Edge-of-Field, Streamgaging, Subsurface-Tile, and Meteorological Stations at Discovery Farms and Pioneer Farm in Wisconsin, 2001-7

    Science.gov (United States)

    Stuntebeck, Todd D.; Komiskey, Matthew J.; Owens, David W.; Hall, David W.

    2008-01-01

    The University of Wisconsin (UW)-Madison Discovery Farms (Discovery Farms) and UW-Platteville Pioneer Farm (Pioneer Farm) programs were created in 2000 to help Wisconsin farmers meet environmental and economic challenges. As a partner with each program, and in cooperation with the Wisconsin Department of Natural Resources and the Sand County Foundation, the U.S. Geological Survey (USGS) Wisconsin Water Science Center (WWSC) installed, maintained, and operated equipment to collect water-quantity and water-quality data from 25 edge-offield, 6 streamgaging, and 5 subsurface-tile stations at 7 Discovery Farms and Pioneer Farm. The farms are located in the southern half of Wisconsin and represent a variety of landscape settings and crop- and animal-production enterprises common to Wisconsin agriculture. Meteorological stations were established at most farms to measure precipitation, wind speed and direction, air and soil temperature (in profile), relative humidity, solar radiation, and soil moisture (in profile). Data collection began in September 2001 and is continuing through the present (2008). This report describes methods used by USGS WWSC personnel to collect, process, and analyze water-quantity, water-quality, and meteorological data for edge-of-field, streamgaging, subsurface-tile, and meteorological stations at Discovery Farms and Pioneer Farm from September 2001 through October 2007. Information presented includes equipment used; event-monitoring and samplecollection procedures; station maintenance; sample handling and processing procedures; water-quantity, waterquality, and precipitation data analyses; and procedures for determining estimated constituent concentrations for unsampled runoff events.

  19. Light Water Reactor Sustainability Program. Digital Architecture Requirements

    Energy Technology Data Exchange (ETDEWEB)

    Thomas, Kenneth [Idaho National Lab. (INL), Idaho Falls, ID (United States); Oxstrand, Johanna [Idaho National Lab. (INL), Idaho Falls, ID (United States)

    2015-03-01

    The Digital Architecture effort is a part of the Department of Energy (DOE) sponsored Light-Water Reactor Sustainability (LWRS) Program conducted at Idaho National Laboratory (INL). The LWRS program is performed in close collaboration with industry research and development (R&D) programs that provides the technical foundations for licensing and managing the long-term, safe, and economical operation of current nuclear power plants (NPPs). One of the primary missions of the LWRS program is to help the U.S. nuclear industry adopt new technologies and engineering solutions that facilitate the continued safe operation of the plants and extension of the current operating licenses. Therefore, a major objective of the LWRS program is the development of a seamless digital environment for plant operations and support by integrating information from plant systems with plant processes for nuclear workers through an array of interconnected technologies. In order to get the most benefits of the advanced technology suggested by the different research activities in the LWRS program, the nuclear utilities need a digital architecture in place to support the technology. A digital architecture can be defined as a collection of information technology (IT) capabilities needed to support and integrate a wide-spectrum of real-time digital capabilities for nuclear power plant performance improvements. It is not hard to imagine that many processes within the plant can be largely improved from both a system and human performance perspective by utilizing a plant wide (or near plant wide) wireless network. For example, a plant wide wireless network allows for real time plant status information to easily be accessed in the control room, field workers’ computer-based procedures can be updated based on the real time plant status, and status on ongoing procedures can be incorporated into smart schedules in the outage command center to allow for more accurate planning of critical tasks. The goal

  20. Cyber security best practices for the nuclear industry

    International Nuclear Information System (INIS)

    Badr, I.

    2012-01-01

    When deploying software based systems, such as, digital instrumentation and controls for the nuclear industry, it is vital to include cyber security assessment as part of architecture and development process. When integrating and delivering software-intensive systems for the nuclear industry, engineering teams should make use of a secure, requirements driven, software development life cycle, ensuring security compliance and optimum return on investment. Reliability protections, data loss prevention, and privacy enforcement provide a strong case for installing strict cyber security policies. (authors)

  1. Cyber security best practices for the nuclear industry

    Energy Technology Data Exchange (ETDEWEB)

    Badr, I. [Rational IBM Software Group, IBM Corporation, Evanston, IL 60201 (United States)

    2012-07-01

    When deploying software based systems, such as, digital instrumentation and controls for the nuclear industry, it is vital to include cyber security assessment as part of architecture and development process. When integrating and delivering software-intensive systems for the nuclear industry, engineering teams should make use of a secure, requirements driven, software development life cycle, ensuring security compliance and optimum return on investment. Reliability protections, data loss prevention, and privacy enforcement provide a strong case for installing strict cyber security policies. (authors)

  2. VERNACULAR ARCHITECTURE: AN INTRODUCTORY COURSE TO LEARN ARCHITECTURE IN INDIA

    Directory of Open Access Journals (Sweden)

    Miki Desai

    2010-07-01

    Full Text Available “The object in view of both my predecessors in office and by myself has been rather to bring out the reasoning powers of individual students, so that they may understand the inner meaning of the old forms and their original function and may develop and modernize and gradually produce an architecture, Indian in character, but at the same time as suited to present day India as the old styles were to their own times and environment.” Claude Batley-1940; Lang, Desai, Desai, 1997 (p.143. The article introduces teaching philosophy, content and method of Basic Design I and II for first year students of architecture at the Faculty of Architecture, Centre for Environmental Planning and Technology (CEPT University, Ahmedabad, India. It is framed within the Indian perspective of architectural education from the British colonial times. Commencing with important academic literature and biases of the initial colonial period, it quickly traces architectural education in CEPT, the sixteenth school of post-independent India, set up in 1962, discussing the foundation year teaching imparted. The school was Modernist and avant-garde. The author introduced these two courses against the back drop of the Universalist Modernist credo of architecture and education. In the courses, the primary philosophy behind learning design emerges from heuristic method. The aim of the first course is seen as infusing interest in visual world, development of manual skills and dexterity through the dictum of ‘Look-feel-reason out-evaluate’ and ‘observe-record-interpret-synthesize transform express’. Due to the lack of architectural orientation in Indian schooling; the second course assumes vernacular architecture as a reasonable tool for a novice to understand the triangular relationship of society, architecture and physical context and its impact on design. The students are analytically exposed to the regional variety of architectures logically stemming from the geo

  3. Survey of medical radium installations in Wisconsin

    International Nuclear Information System (INIS)

    Tapert, A.C.; Lea, W.L.

    1975-05-01

    A radiation protection survey was performed at 70 medical radium installations in the State of Wisconsin. The requirements of the State's Radiation Protection Code were used as survey criteria. Radiation measurements of radium storage containers, radium capsule leakage tests, and monitoring of work surfaces for contamination were performed. Film badge monitoring data of whole body and extremity doses are presented for 221 individuals at 17 hospitals. Whole body doses during single treatments ranged from 10 to 1360 mrems per individual. The estimate of 500 mrems per treatment was determined as the dose aggregate to hospital personnel. Whole body doses from film badges are compared with analogous TLD doses. Four physicians and six technicians at nine hospitals participated in a study for monitoring the extremities with TLD. Cumulative extremity doses ranged from 28 to 6628 mrems per participant during the study. (U.S.)

  4. Architecture Descriptions. A Contribution to Modeling of Production System Architecture

    DEFF Research Database (Denmark)

    Jepsen, Allan Dam; Hvam, Lars

    a proper understanding of the architecture phenomenon and the ability to describe it in a manner that allow the architecture to be communicated to and handled by stakeholders throughout the company. Despite the existence of several design philosophies in production system design such as Lean, that focus...... a diverse set of stakeholder domains and tools in the production system life cycle. To support such activities, a contribution is made to the identification and referencing of production system elements within architecture descriptions as part of the reference architecture framework. The contribution...

  5. Digital Architecture Planning Model

    International Nuclear Information System (INIS)

    Oxstrand, Johanna Helene; Al Rashdan, Ahmad Yahya Mohammad; Bly, Aaron Douglas; Rice, Brandon Charles; Fitzgerald, Kirk; Wilson, Keith Leon

    2016-01-01

    As part of the U.S. Department of Energy's Light Water Reactor Sustainability Program, the Digital Architecture (DA) Project focuses on providing a model that nuclear utilities can refer to when planning deployment of advanced technologies. The digital architecture planning model (DAPM) is the methodology for mapping power plant operational and support activities into a DA that unifies all data sources needed by the utilities to operate their plants. The DA is defined as a collection of information technology capabilities needed to support and integrate a wide spectrum of real-time digital capabilities for performance improvements of nuclear power plants. DA can be thought of as integration of the separate instrumentation and control and information systems already in place in nuclear power plants, which are brought together for the purpose of creating new levels of automation in plant work activities. A major objective in DAPM development was to survey all key areas that needed to be reviewed in order for a utility to make knowledgeable decisions regarding needs and plans to implement a DA at the plant. The development was done in two steps. First, researchers surveyed the nuclear industry in order to learn their near-term plans for adopting new advanced capabilities and implementing a network (i.e., wireless and wire) infrastructure throughout the plant, including the power block. Secondly, a literature review covering regulatory documents, industry standards, and technical research reports and articles was conducted. The objective of the review was to identify key areas to be covered by the DAPM, which included the following: 1. The need for a DA and its benefits to the plant 2. Resources required to implement the DA 3. Challenges that need to be addressed and resolved to implement the DA 4. Roles and responsibilities of the DA implementation plan. The DAPM was developed based on results from the survey and the literature review. Model development

  6. Digital Architecture Planning Model

    Energy Technology Data Exchange (ETDEWEB)

    Oxstrand, Johanna Helene [Idaho National Lab. (INL), Idaho Falls, ID (United States). Light Water Reactor Sustainability Program (LWRS); Al Rashdan, Ahmad Yahya Mohammad [Idaho National Lab. (INL), Idaho Falls, ID (United States). Light Water Reactor Sustainability Program (LWRS); Bly, Aaron Douglas [Idaho National Lab. (INL), Idaho Falls, ID (United States). Light Water Reactor Sustainability Program (LWRS); Rice, Brandon Charles [Idaho National Lab. (INL), Idaho Falls, ID (United States). Light Water Reactor Sustainability Program (LWRS); Fitzgerald, Kirk [Idaho National Lab. (INL), Idaho Falls, ID (United States). Light Water Reactor Sustainability Program (LWRS); Wilson, Keith Leon [Idaho National Lab. (INL), Idaho Falls, ID (United States). Light Water Reactor Sustainability Program (LWRS)

    2016-03-01

    As part of the U.S. Department of Energy’s Light Water Reactor Sustainability Program, the Digital Architecture (DA) Project focuses on providing a model that nuclear utilities can refer to when planning deployment of advanced technologies. The digital architecture planning model (DAPM) is the methodology for mapping power plant operational and support activities into a DA that unifies all data sources needed by the utilities to operate their plants. The DA is defined as a collection of information technology capabilities needed to support and integrate a wide spectrum of real-time digital capabilities for performance improvements of nuclear power plants. DA can be thought of as integration of the separate instrumentation and control and information systems already in place in nuclear power plants, which are brought together for the purpose of creating new levels of automation in plant work activities. A major objective in DAPM development was to survey all key areas that needed to be reviewed in order for a utility to make knowledgeable decisions regarding needs and plans to implement a DA at the plant. The development was done in two steps. First, researchers surveyed the nuclear industry in order to learn their near-term plans for adopting new advanced capabilities and implementing a network (i.e., wireless and wire) infrastructure throughout the plant, including the power block. Secondly, a literature review covering regulatory documents, industry standards, and technical research reports and articles was conducted. The objective of the review was to identify key areas to be covered by the DAPM, which included the following: 1. The need for a DA and its benefits to the plant 2. Resources required to implement the DA 3. Challenges that need to be addressed and resolved to implement the DA 4. Roles and responsibilities of the DA implementation plan. The DAPM was developed based on results from the survey and the literature review. Model development, including

  7. Initial validation of ATLAS software on the ARM architecture

    Energy Technology Data Exchange (ETDEWEB)

    Kawamura, Gen; Quadt, Arnulf; Smith, Joshua Wyatt [II. Physikalisches Institut, Georg-August Universitaet Goettingen (Germany); Seuster, Rolf [TRIUMF (Canada); Stewart, Graeme [University of Glasgow (United Kingdom)

    2016-07-01

    In the early 2000's the introduction of the multi-core era of computing helped industry and experiments such as ATLAS realize even more computing power. This was necessary as the limits of what a single-core processor could do where quickly being reached. Our current model of computing is to increase the number of multi-core nodes in a server farm in order to handle the increased influx of data. As power costs and our need for more computing power increase, this model will eventually become non-realistic. Once again a paradigm shift has to take place. One such option is to look at alternative architectures for large scale server farms. ARM processors are such an example. Making up approximately 95 % of the smartphone and tablet market these processors are widely available, very power conservative and constantly becoming faster. The ATLAS software code base (Athena) is extremely complex comprising of more than 6.5 million lines of code. It has very recently been ported to the ARM 64-bit architecture. The process of our port as well as the first validation plots are presented and compared to the traditional x86 architecture.

  8. A real-time control system architecture for industrial power amplifiers

    NARCIS (Netherlands)

    Qureshi, F.; Spinu, V.; Wijnands, C.G.E.; Lazar, M.

    2013-01-01

    Power amplifiers are a highly important component in a range of industrial applications, such as, servo-drives, magnetic resonance imaging, energy systems, and audio. The control system for power amplifiers should satisfy a range of requirements, e.g., offset free tracking, stability margins, and

  9. 78 FR 57501 - Approval and Promulgation of Air Quality Implementation Plans; Wisconsin; Amendments to Vehicle...

    Science.gov (United States)

    2013-09-19

    ... Definitions, NR 485.04 Motor vehicle emission limitations; exemptions, and NR 485.045 Repair cost limit for... Promulgation of Air Quality Implementation Plans; Wisconsin; Amendments to Vehicle Inspection and Maintenance... Resources on June 7, 2012, concerning the state's vehicle inspection and maintenance (I/M) program in...

  10. 78 FR 34966 - Approval and Promulgation of Air Quality Implementation Plans; Wisconsin; Removal of Gasoline...

    Science.gov (United States)

    2013-06-11

    ... Promulgation of Air Quality Implementation Plans; Wisconsin; Removal of Gasoline Vapor Recovery From Southeast... specifically installed at gasoline dispensing facilities (GDF) and capture the refueling fuel vapors at the gasoline pump nozzle. The system carries the vapors back to the underground storage tank at the GDF to...

  11. Interdisciplinary skills in architectural and engineering education programs

    DEFF Research Database (Denmark)

    Andersson, Niclas; Andersson, Pernille Hammar

    2006-01-01

    and requirements for reinforcement of the interdisciplinary skills within the architectural and engineering education programs as to face the challenges from industry. The study claims that the development of interdisciplinary skills should be regarded a pedagogical issue that can be accomplished by integrative...... project. Besides, new and more integrated forms of co-operation between the various actors make the prevalent professional disciplines more ambiguous and it compels into a need for trans-professional skills among the actors. In contrast to the requirements for interdisciplinary skills, the educational...... training programmes of architects and engineers are traditionally characterised by strict disciplinary boundaries. Thus, the prevailing educational system is challenged to meet the demands for trans-professional skills within industry. The purpose of this paper is to outline some pedagogical prerequisites...

  12. Architecture and Film

    OpenAIRE

    Mohammad Javaheri, Saharnaz

    2016-01-01

    Film does not exist without architecture. In every movie that has ever been made throughout history, the cinematic image of architecture is embedded within the picture. Throughout my studies and research, I began to see that there is no director who can consciously or unconsciously deny the use of architectural elements in his or her movies. Architecture offers a strong profile to distinguish characters and story. In the early days, films were shot in streets surrounde...

  13. Mechanisms of Termite Spread in Wisconsin and Potential Consequences as a Result of Changing Climate Trends

    Science.gov (United States)

    R. A. Arango; F. III Green; G.R. Esenther; D.A. Marschalek; M.E. Berres; K.F. Raffa

    2014-01-01

    Mature colonies of Reticulitermes spp. reproduce and spread mainly by secondary (rather than alate) reproductives throughout their geographical distribution, but especially near the northern boundaries of their range. Historically in Wisconsin, winged reproductives of the one established species, Reticulitermes flavipes (Kollar),...

  14. Architectural geometry

    KAUST Repository

    Pottmann, Helmut

    2014-11-26

    Around 2005 it became apparent in the geometry processing community that freeform architecture contains many problems of a geometric nature to be solved, and many opportunities for optimization which however require geometric understanding. This area of research, which has been called architectural geometry, meanwhile contains a great wealth of individual contributions which are relevant in various fields. For mathematicians, the relation to discrete differential geometry is significant, in particular the integrable system viewpoint. Besides, new application contexts have become available for quite some old-established concepts. Regarding graphics and geometry processing, architectural geometry yields interesting new questions but also new objects, e.g. replacing meshes by other combinatorial arrangements. Numerical optimization plays a major role but in itself would be powerless without geometric understanding. Summing up, architectural geometry has become a rewarding field of study. We here survey the main directions which have been pursued, we show real projects where geometric considerations have played a role, and we outline open problems which we think are significant for the future development of both theory and practice of architectural geometry.

  15. Architectural geometry

    KAUST Repository

    Pottmann, Helmut; Eigensatz, Michael; Vaxman, Amir; Wallner, Johannes

    2014-01-01

    Around 2005 it became apparent in the geometry processing community that freeform architecture contains many problems of a geometric nature to be solved, and many opportunities for optimization which however require geometric understanding. This area of research, which has been called architectural geometry, meanwhile contains a great wealth of individual contributions which are relevant in various fields. For mathematicians, the relation to discrete differential geometry is significant, in particular the integrable system viewpoint. Besides, new application contexts have become available for quite some old-established concepts. Regarding graphics and geometry processing, architectural geometry yields interesting new questions but also new objects, e.g. replacing meshes by other combinatorial arrangements. Numerical optimization plays a major role but in itself would be powerless without geometric understanding. Summing up, architectural geometry has become a rewarding field of study. We here survey the main directions which have been pursued, we show real projects where geometric considerations have played a role, and we outline open problems which we think are significant for the future development of both theory and practice of architectural geometry.

  16. Working heritage : managing industrial heritage still in use : industrial strength : maintaining use

    Energy Technology Data Exchange (ETDEWEB)

    Deom, C. [Montreal Univ., PQ (Canada); Deschenes, M.J. [Hydro-Quebec, Montreal, PQ (Canada)

    2009-07-01

    A joint project was conducted by the University of Montreal and Hydro-Quebec to assess the heritage of the power utility's buildings and equipment assets. The study determined the heritage value of 3 hydroelectric stations by identifying elements and features for their future preservation. Two of the stations have been used for nearly 75 years. The paper also investigated the heritage value of sites where industrial activity is still in progress, and discussed methods of determine the heritage value of equipment and architecture. The stations have undergone significant modifications as a result of innovations in energy transport, transformation and distribution technologies. The ongoing transformations and innovations at industrial heritage sites were discussed in relation to heritage value. The challenges associated with maintaining usefulness and preserving heritage values were also evaluated. 1 fig.

  17. 77 FR 46952 - Approval and Promulgation of Air Quality Implementation Plans; Wisconsin; Regional Haze

    Science.gov (United States)

    2012-08-07

    ... July 31, 2018. Wisconsin submitted its regional haze plan on January 18, 2012, with a supplemental.... Response: In cases like this where a subject is addressed by both the general guidance in the draft... option at that time. Further, this approach does not require an election of one set of mass caps by July...

  18. Aerospace Patented High-Strength Aluminum Alloy Used in Commercial Industries

    Science.gov (United States)

    2004-01-01

    NASA structural materials engineers at Marshall Space Flight Center (MSFC) in Huntsville, Alabama developed a high-strength aluminum alloy for aerospace applications with higher strength and wear-resistance at elevated temperatures. The alloy is a solution to reduce costs of aluminum engine pistons and lower engine emissions for the automobile industry. The Boats and Outboard Engines Division at Bombardier Recreational Products of Sturtevant, Wisconsin is using the alloy for pistons in its Evinrude E-Tec outboard, 40-90 horsepower, engine line. The alloy pistons make the outboard motor quieter and cleaner, while improving fuel mileage and increasing engine durability. The engines comply with California Air resources Board emissions standards, some of the most stringent in the United States. (photo credit: Bombardiier Recreational Products)

  19. Feasibility Study of Economics and Performance of Solar Photovoltaics at the Refuse Hideaway Landfill in Middleton, Wisconsin

    Energy Technology Data Exchange (ETDEWEB)

    Salasovich, J.; Mosey, G.

    2011-08-01

    This report presents the results of an assessment of the technical and economic feasibility of deploying a photovoltaics (PV) system on a brownfield site at the Refuse Hideaway Landfill in Middleton, Wisconsin. The site currently has a PV system in place and was assessed for further PV installations. The cost, performance, and site impacts of different PV options were estimated. The economics of the potential systems were analyzed using an electric rate of $0.1333/kWh and incentives offered by the State of Wisconsin and by the serving utility, Madison Gas and Electric. According to the site production calculations, the most cost-effective system in terms of return on investment is the thin-film fixed-tilt technology. The report recommends financing options that could assist in the implementation of such a system.

  20. Elements of Architecture

    DEFF Research Database (Denmark)

    Elements of Architecture explores new ways of engaging architecture in archaeology. It conceives of architecture both as the physical evidence of past societies and as existing beyond the physical environment, considering how people in the past have not just dwelled in buildings but have existed...

  1. La gouvernance des projets d’architecture : une typologie de la multi-organisation temporaire

    Directory of Open Access Journals (Sweden)

    Gonzalo Lizarralde

    2010-11-01

    Full Text Available Traditional approaches to ethics in architecture have focused on three characteristics of the object: durability, convenience and beauty (firmitas, utilitas and venustas. On the other hand, recent knowledge derived from the fields of project management and sustainable development has made significant contributions to the understanding of project governance. However, the relationships of governance within architectural projects are linked to the characteristics of the construction industry, a sector that operates through the creation of temporary teams formed by highly specialized organizations. We present in this article some of these characteristics and their influence on the relations between project participants. A systems approach based on the review of case studies helps us identify the complexity of the temporary teams involved in architectural projects. The identification of various types of organizational configurations highlights some ethical issues related to formal and informal relationships between stakeholders and those between the architect and complex construction clients. We argue that the architect is faced with the challenge of working on an architectural project that is —increasingly— the subject of negotiation between stakeholders. Faced with this challenge, it is crucial for the architect to understand the complexity of the relationships between participants within the project social system and to create the appropriate mechanisms of participation, negotiation and exchange between them.RÉSUMÉLes débats éthiques sur l’architecture ont traditionnellement abordé trois thématiques récurrentes : la beauté, la solidité et l’utilité de l’œuvre architecturale. Plus récemment, les nouvelles connaissances provenant du domaine de la gestion des projets et du développement durable ont apporté d’importantes contributions à la compréhension de la gouvernance de projets. Cependant, la démarche de r

  2. PICNIC Architecture.

    Science.gov (United States)

    Saranummi, Niilo

    2005-01-01

    The PICNIC architecture aims at supporting inter-enterprise integration and the facilitation of collaboration between healthcare organisations. The concept of a Regional Health Economy (RHE) is introduced to illustrate the varying nature of inter-enterprise collaboration between healthcare organisations collaborating in providing health services to citizens and patients in a regional setting. The PICNIC architecture comprises a number of PICNIC IT Services, the interfaces between them and presents a way to assemble these into a functioning Regional Health Care Network meeting the needs and concerns of its stakeholders. The PICNIC architecture is presented through a number of views relevant to different stakeholder groups. The stakeholders of the first view are national and regional health authorities and policy makers. The view describes how the architecture enables the implementation of national and regional health policies, strategies and organisational structures. The stakeholders of the second view, the service viewpoint, are the care providers, health professionals, patients and citizens. The view describes how the architecture supports and enables regional care delivery and process management including continuity of care (shared care) and citizen-centred health services. The stakeholders of the third view, the engineering view, are those that design, build and implement the RHCN. The view comprises four sub views: software engineering, IT services engineering, security and data. The proposed architecture is founded into the main stream of how distributed computing environments are evolving. The architecture is realised using the web services approach. A number of well established technology platforms and generic standards exist that can be used to implement the software components. The software components that are specified in PICNIC are implemented in Open Source.

  3. Hybrid Architecture for Coordination of AGVs in FMS

    Directory of Open Access Journals (Sweden)

    Eduardo G. Hernandez-Martinez

    2014-03-01

    Full Text Available This paper presents a hybrid control architecture that coordinates the motion of groups of automated guided vehicles in flexible manufacturing systems. The high-level control is based on a Petri net model, using the industrial standard ISA-95, obtaining a task-based coordination of equipment and storage considering process restrictions, logical precedences, shared resources and the assignment of robots to move workpieces individually or in subgroups. On the other hand, in the low-level control, three basic control laws are designed for unicycle-type robots in order to achieve desired formation patterns and marching behaviours, avoiding inter-robot collisions. The control scheme combines the task assignment for the robots obtained from the discrete-event model and the implementation of formation and marching continuous control laws applied to the motion of the mobile robots. The hybrid architecture is implemented and validated for the case of a flexible manufacturing system and four mobile robots using a virtual reality platform.

  4. Research in the Doctoral Program in Second Language Acquisition at the University of Wisconsin-Madison

    Science.gov (United States)

    De Costa, Peter I.; Bernales, Carolina; Merrill, Margaret

    2011-01-01

    Faculty and graduate students in the Doctoral Program in Second Language Acquisition (SLA) at the University of Wisconsin-Madison engage in a broad spectrum of research. From Professor Sally Magnan's research on study abroad and Professor Monika Chavez's work in foreign language policy through Professor Richard Young's examination of…

  5. Urban and community forests of the North Central East region: Illinois, Indiana, Michigan, Ohio, Wisconsin

    Science.gov (United States)

    David J. Nowak; Eric J. Greenfield

    2010-01-01

    This report details how land cover and urbanization vary within the states of Illinois, Indiana, Michigan, Ohio, and Wisconsin by community (incorporated and census designated places), county subdivision, and county. Specifically this report provides critical urban and community forestry information for each state including human population characteristics and trends,...

  6. Putting Anti-Indian Violence in Context. The Case of the Great Lakes Chippewas of Wisconsin

    Science.gov (United States)

    Perry, Barbara; Robyn, Linda

    2005-01-01

    The Chippewas of Northern Wisconsin continue to experience a peculiarly American form of apartheid, characterized by segregation, discrimination, cultural imperialism, and everyday violence. While the blatant stigmatization, disempowerment, and violence reached its modern day zenith in the spear fishing conflict of the 1980s and 1990s, ongoing…

  7. Space architecture for MoonVillage

    Science.gov (United States)

    Sherwood, Brent

    2017-10-01

    The concept of a multinational MoonVillage, as proposed by Jan Wörner of ESA, is analyzed with respect to diverse factors affecting its implementation feasibility: potential activities and scale as a function of location, technology, and purpose; potential participants and their roles; business models for growth and sustainability as compared to the ISS; and implications for the field of space architecture. Environmental and operations constraints that govern all types of MoonVillage are detailed. Findings include: 1) while technically feasible, a MoonVillage would be more distributed and complex a project than the ISS; 2) significant and distinctive opportunities exist for willing participants, at all evolutionary scales and degrees of commercialization; 3) the mixed-use space business park model is essential for growth and permanence; 4) growth depends on exporting lunar material products, and the rate and extent of growth depends on export customers including terrestrial industries; 5) industrial-scale operations are a precondition for lunar urbanism, which goal in turn dramatically drives technology requirements; but 6) industrial viability cannot be discerned until significant in situ operations occur; and therefore 7) government investment in lunar surface operations is a strictly enabling step. Because of the resources it could apply, the U.S. government holds the greatest leverage on growth, no matter who founds a MoonVillage. The interplanetary business to be built may because for engagement.

  8. Architectural Theatricality

    DEFF Research Database (Denmark)

    Tvedebrink, Tenna Doktor Olsen

    environments and a knowledge gap therefore exists in present hospital designs. Consequently, the purpose of this thesis has been to investigate if any research-based knowledge exist supporting the hypothesis that the interior architectural qualities of eating environments influence patient food intake, health...... and well-being, as well as outline a set of basic design principles ‘predicting’ the future interior architectural qualities of patient eating environments. Methodologically the thesis is based on an explorative study employing an abductive approach and hermeneutic-interpretative strategy utilizing tactics...... and food intake, as well as a series of references exist linking the interior architectural qualities of healthcare environments with the health and wellbeing of patients. On the basis of these findings, the thesis presents the concept of Architectural Theatricality as well as a set of design principles...

  9. Architecture of Institution & Home. Architecture as Cultural Medium

    NARCIS (Netherlands)

    Robinson, J.W.

    2004-01-01

    This dissertation addresses how architecture functions as a cultural medium. It does so by by investigating how the architecture of institution and home each construct and support different cultural practices. By studying the design of ordinary settings in terms of how qualitative differences in

  10. On Detailing in Contemporary Architecture

    DEFF Research Database (Denmark)

    Kristensen, Claus; Kirkegaard, Poul Henning

    2010-01-01

    Details in architecture have a significant influence on how architecture is experienced. One can touch the materials and analyse the detailing - thus details give valuable information about the architectural scheme as a whole. The absence of perceptual stimulation like details and materiality...... / tactility can blur the meaning of the architecture and turn it into an empty statement. The present paper will outline detailing in contemporary architecture and discuss the issue with respect to architectural quality. Architectural cases considered as sublime piece of architecture will be presented...

  11. Automated Work Package: Conceptual Design and Data Architecture

    Energy Technology Data Exchange (ETDEWEB)

    Al Rashdan, Ahmad [Idaho National Lab. (INL), Idaho Falls, ID (United States); Oxstrand, Johanna [Idaho National Lab. (INL), Idaho Falls, ID (United States); Agarwal, Vivek [Idaho National Lab. (INL), Idaho Falls, ID (United States)

    2016-05-26

    frontend aspects of the AWP, the backend data architecture was researched and developed in this effort. The backend design involved data architecture aspects. It was realized through this effort that the key aspects of this design are hierarchy, data configuration and live information, data templates and instances, the flow of work package execution, the introduction of properties, and the means to interface the backend to the frontend. After the backend design was developed, a data structure was built to reflect the developed data architecture. The data structure was developed to accommodate the fifty functionalities identified by the envisioned scenario development. The data structure was evaluated by incorporating an example work order from the nuclear power industry. The implementation resulted in several optimization iterations of the data structure. In addition, the rearrangement of the work order information to fit the data structure highlighted several possibilities for improvement in the current work order design, and significantly reduced the size of the work order.

  12. Automated Work Package: Conceptual Design and Data Architecture

    International Nuclear Information System (INIS)

    Al Rashdan, Ahmad; Oxstrand, Johanna; Agarwal, Vivek

    2016-01-01

    aspects of the AWP, the backend data architecture was researched and developed in this effort. The backend design involved data architecture aspects. It was realized through this effort that the key aspects of this design are hierarchy, data configuration and live information, data templates and instances, the flow of work package execution, the introduction of properties, and the means to interface the backend to the frontend. After the backend design was developed, a data structure was built to reflect the developed data architecture. The data structure was developed to accommodate the fifty functionalities identified by the envisioned scenario development. The data structure was evaluated by incorporating an example work order from the nuclear power industry. The implementation resulted in several optimization iterations of the data structure. In addition, the rearrangement of the work order information to fit the data structure highlighted several possibilities for improvement in the current work order design, and significantly reduced the size of the work order.

  13. Using the index of biotic integrity (IBI) to measure environmental quality in warmwater streams of Wisconsin.

    Science.gov (United States)

    John Lyons

    1992-01-01

    Describes an index based on attributes of fish assemblages that has proven effective in assessing biotic integrity and environmental health in intermediate-sized, warmwater (i.e., too warm for salmonids) streams and rivers of Wisconsin. Provides detailed guidelines for applying this index.

  14. Soil Exchangeable Phosphorus Pools, Equilibrium Characteristics, and Mass Distribution Coefficients for Eight-Mile Run Watershed, Wisconsin

    Science.gov (United States)

    2009-09-01

    Galle River Basin, west-central Wisconsin (Figure 1). Livestock ( dairy ) pasture and associated barnyards represent approximately 6 percent of the...Reddy. 1998. Dairy manure influences on phosphorus retention capacity of Spodosols. J. Environ. Qual. 27:522-527. Pierzynski, G. M. 2000. Methods

  15. Development of enterprise architecture management methodology for teaching purposes

    Directory of Open Access Journals (Sweden)

    Dmitry V. Kudryavtsev

    2017-01-01

    the main methods and technologies of the enterprise architecture in practice. The requirements for the simplified methodology were defined.These requirements were taken into account during methodology development and can be used when applying the methodology – it will be possible to understand the goals that can be achieved with its help, the assumptions made and the existing limitations. The proposed methodology defines the layers, aspects and objects of the enterprise architecture, describes the tasks of managing enterprise architecture and the artifacts created (lists, matrices, diagrams.The proposed methodology can be used to conduct training projects in which methods and tools of enterprise architecture management are used to optimize the company’s work based on the capabilities of information technology. Such projects will help not only to develop students’ skills, but also to establish a dialogue between universities and industry – the provider of problems and tasks for solving within students’ projects.The proposed simplified methodology for managing the architecture of the enterprise is tested and used by the authors when conducting courses in the leading universities of the Russian Federation: Graduate School of Management (St. Petersburg State University, St. Petersburg State University, Finance University under the Government of the Russian Federation, Higher School of Economics and BonchBruevich Saint-Petersburg State University of Telecommunications.

  16. Systemic Architecture

    DEFF Research Database (Denmark)

    Poletto, Marco; Pasquero, Claudia

    -up or tactical design, behavioural space and the boundary of the natural and the artificial realms within the city and architecture. A new kind of "real-time world-city" is illustrated in the form of an operational design manual for the assemblage of proto-architectures, the incubation of proto-gardens...... and the coding of proto-interfaces. These prototypes of machinic architecture materialize as synthetic hybrids embedded with biological life (proto-gardens), computational power, behavioural responsiveness (cyber-gardens), spatial articulation (coMachines and fibrous structures), remote sensing (FUNclouds...

  17. An Efficient SDN Multicast Architecture for Dynamic Industrial IoT Environments

    Directory of Open Access Journals (Sweden)

    Hyeong-Su Kim

    2018-01-01

    Full Text Available Large-scale industrial IoT services appear in smart factory domains such as factory clouds which integrate distributed small factories into a large virtual factory with dynamic combination based on orders of consumers. A smart factory has so many industrial elements including various sensors/actuators, gateways, controllers, application servers, and IoT clouds. Since there are complex connections and relations, it is hard to handle them in point-to-point manner. In addition, many duplicated traffics are exchanged between them through the Internet. Multicast is believed as an effective many-to-many communication mechanism by establishing multicast trees between sources and receivers. There are, however, some issues for adopting multicast to large-scale industrial IoT services in terms of QoS. In this paper, we propose a novel software-defined network multicast based on group shared tree which includes near-receiver rendezvous point selection algorithm and group shared tree switching mechanism. As a result, the proposed multicast mechanism can reduce the packet loss by 90% compared to the legacy methods under severe congestion condition. GST switching method obtains to decreased packet delay effect, respectively, 2%, 20% better than the previously studied multicast and the legacy SDN multicast.

  18. Tackling optimization challenges in industrial load control and full-duplex radios

    Science.gov (United States)

    Gholian, Armen

    In price-based demand response programs in smart grid, utilities set the price in accordance with the grid operating conditions and consumers respond to price signals by conducting optimal load control to minimize their energy expenditure while satisfying their energy needs. Industrial sector consumes a large portion of world electricity and addressing optimal load control of energy-intensive industrial complexes, such as steel industry and oil-refinery, is of practical importance. Formulating a general industrial complex and addressing issues in optimal industrial load control in smart grid is the focus of the second part of this dissertation. Several industrial load details are considered in the proposed formulation, including those that do not appear in residential or commercial load control problems. Operation under different smart pricing scenarios, namely, day-ahead pricing, time-of-use pricing, peak pricing, inclining block rates, and critical peak pricing are considered. The use of behind-the-meter renewable generation and energy storage is also considered. The formulated optimization problem is originally nonlinear and nonconvex and thus hard to solve. However, it is then reformulated into a tractable linear mixed-integer program. The performance of the design is assessed through various simulations for an oil refinery and a steel mini-mill. In the third part of this dissertation, a novel all-analog RF interference canceler is proposed. Radio self-interference cancellation (SIC) is the fundamental enabler for full-duplex radios. While SIC methods based on baseband digital signal processing and/or beamforming are inadequate, an all-analog method is useful to drastically reduce the self-interference as the first stage of SIC. It is shown that a uniform architecture with uniformly distributed RF attenuators has a performance highly dependent on the carrier frequency. It is also shown that a new architecture with the attenuators distributed in a clustered

  19. Architecture in Its Own Shadow

    Directory of Open Access Journals (Sweden)

    Alexander Rappaport

    2016-11-01

    Full Text Available Those who consider themselves architects disapprove of the statements about destruction of the subject of architectural culture, profession and of the subject of architectural theory. At the same time, a deep crisis of both theory and practice is obvious. When theorists of architecture of the 20th and early 21st centuries turned to the subjects external to architecture – sociology, psychology, semiotics, ecology, post-structuralist criticism, etc., instead of enriching and renovating the architectural theory, the results were just the opposite. A brand new and independent paradigm of architecture is needed. It should contain three parts specific by their logical-subject nature: ontology of architecture, methodology of architectural thought and axiology of architectural thought.

  20. Restoring Wisconsin Art Therapy Association in Art Therapy History: Implications for Professional Definition and Inclusivity

    Science.gov (United States)

    Potash, Jordan; Burnie, Michele; Pearson, Rosemary; Ramirez, Wayne

    2016-01-01

    The Wisconsin Art Therapy Association (WATA), formally established in 1969, was the first incorporated organization of art therapists in the United States. Under the leadership of Wayne Ramirez, WATA lobbied the national association for an inclusive definition of art therapy that aimed to foster respect for psychiatric, educational, and community…

  1. Gay Men's Book Clubs versus Wisconsin's Public Libraries: Political Perceptions in the Absence of Dialogue

    Science.gov (United States)

    Pruitt, John

    2010-01-01

    Because of an absence of dialogue, a tense relationship appears to exist between Wisconsin's gay men's book discussion groups and their local public libraries. Public library directors express interest in accommodating these groups if approached but face budget restrictions and local communities that may oppose these gatherings; gay men's book…

  2. Short History of the advertising industrial publicity in Mexico. The industrial estate of Puebla between the old regime and the revolution: 1880-1920 (industrial intangible heritage rescue

    Directory of Open Access Journals (Sweden)

    Humberto Morales Moreno

    2011-03-01

    Full Text Available This paper aims to show with archaeological field work in different landscapes of Mexico and documentation of the municipal archives of the city of Puebla, the architectural and historical evidence that gave identity to the Mexican industrial past throughout the 19th and first half of 20th century. Also shows the importance of the public documentation that many family firms produced in their correspondence to the municipal authority, demanding all kinds of grants or concessions in the city ofPuebla between 1880-1920. This iconographic industrial advertising and its evolution alongside this kind of correspondence is not only very important for the history of industrial brands and advertising, but it is also a keynote to the history of companies in the emblematic town of Puebla, that is not only distinguished by being a textile town, between 1880-1940, but a major industrial and commercial corridor.

  3. Linkages To Engagement At University of Wisconsin-Parkside

    Science.gov (United States)

    Evans, C. V.

    2007-12-01

    The University of Wisconsin-Parkside Department of Geosciences is a small but successful department within one of the smallest comprehensive universities in the University of Wisconsin system. Formerly a more traditional "rocks and petroleum" program, the Department was on the verge of extinction in 1999. Fortunately, a farsighted Dean intervened and proposed a change of direction for the department, filling in behind retirements with new leadership and a strong environmental focus. Several strategies have been key to resuscitating the Department to its current status, increasing majors, faculty, and SCH/FTE. First, we embraced our niche as the environmental resource, specifically offering urban or other developed settings for our focus on environmental quality. Secondly we revamped our majors' curriculum to enable our students to learn to integrate practical technological skills in sampling, analysis, instrumentation use, and civic engagement to produce positive outcomes at both physical and social levels. Thirdly, our Department has become a strong and active supporter of a teacher preparation program that is undergoing important curriculum and organizational changes. Our newest faculty addition is an atmospheric chemist with significant teaching responsibility in our campus' new Liberal Arts major for elementary school teachers. Geosciences faculty also vigorously support a certificate program in Community Based Learning, direct the campus minor in Environmental Studies, and have actively participated in campus initiatives such as First Year Experience, General Education reform, the campus' Teaching and Learning Center, and collaborative course offerings that link academic skills (math, reading, writing) courses to extra support in General Education science courses. In addition, the Department has taken campus leadership in participation in the national SENCER initiative, which links science education and civic engagement. Finally, we have also amended and

  4. Architectural technology

    DEFF Research Database (Denmark)

    2005-01-01

    The booklet offers an overall introduction to the Institute of Architectural Technology and its projects and activities, and an invitation to the reader to contact the institute or the individual researcher for further information. The research, which takes place at the Institute of Architectural...... Technology at the Roayl Danish Academy of Fine Arts, School of Architecture, reflects a spread between strategic, goal-oriented pilot projects, commissioned by a ministry, a fund or a private company, and on the other hand projects which originate from strong personal interests and enthusiasm of individual...

  5. Humanizing Architecture

    DEFF Research Database (Denmark)

    Toft, Tanya Søndergaard

    2015-01-01

    The article proposes the urban digital gallery as an opportunity to explore the relationship between ‘human’ and ‘technology,’ through the programming of media architecture. It takes a curatorial perspective when proposing an ontological shift from considering media facades as visual spectacles...... agency and a sense of being by way of dematerializing architecture. This is achieved by way of programming the symbolic to provide new emotional realizations and situations of enlightenment in the public audience. This reflects a greater potential to humanize the digital in media architecture....

  6. Robotic architectures

    CSIR Research Space (South Africa)

    Mtshali, M

    2010-01-01

    Full Text Available In the development of mobile robotic systems, a robotic architecture plays a crucial role in interconnecting all the sub-systems and controlling the system. The design of robotic architectures for mobile autonomous robots is a challenging...

  7. 76 FR 22748 - Wisconsin Central Ltd.-Intra-Corporate Family Merger Exemption-Duluth, Missabe and Iron Range...

    Science.gov (United States)

    2011-04-22

    ... Ltd.--Intra-Corporate Family Merger Exemption-- Duluth, Missabe and Iron Range Railway Company and Duluth, Winnipeg and Pacific Railway Company Wisconsin Central Ltd. (WCL), Duluth, Missabe and Iron Range Railway Company (DMIR) and Duluth, Winnipeg and Pacific Railway Company (DWP) have jointly filed a...

  8. 77 FR 38821 - Final Environmental Impact Statement for the Menominee Indian Tribe of Wisconsin's Proposed Fee...

    Science.gov (United States)

    2012-06-29

    ..., with the Menominee Indian Tribe of Wisconsin (Tribe), the National Indian Gaming Commission (NIGC), the... III gaming would be conducted inside the existing clubhouse until the new casino is built. The FEIS..., environmental justice, cumulative effects, indirect effects and mitigation. The BIA has afforded other...

  9. 76 FR 14351 - Proposed Withdrawal of Certain Federal Aquatic Life Water Quality Criteria Applicable to Wisconsin

    Science.gov (United States)

    2011-03-16

    ... Proposed Withdrawal of Certain Federal Aquatic Life Water Quality Criteria Applicable to Wisconsin AGENCY... aquatic life water quality criteria for chronic and acute copper and nickel, and chronic endrin and...., Washington, DC 20460 or Francine Norling, Proposed Withdrawal of Certain Federal Aquatic Life Water Quality...

  10. Architecture Sustainability

    NARCIS (Netherlands)

    Avgeriou, Paris; Stal, Michael; Hilliard, Rich

    2013-01-01

    Software architecture is the foundation of software system development, encompassing a system's architects' and stakeholders' strategic decisions. A special issue of IEEE Software is intended to raise awareness of architecture sustainability issues and increase interest and work in the area. The

  11. Plasma resistivity measurements in the Wisconsin levitated octupole

    International Nuclear Information System (INIS)

    Brouchous, D.A.

    1980-11-01

    Resistivity measurements parallel to the magnetic field were made on gun injected plasmas ranging in density from 10 9 cm -3 to 10 1 parallelcm -3 in the Wisconsin levitated octupole with toroidal and poloidal magnetic fields. The 10 9 cm -3 plasma was collisionless with lambda/sub mfp/ > 100 mirror lengths, had T/sub e/ = 10 eV, T/sub i/ = 30 eV and was found to have anomalous resistivity scaling like eta = √T/sub e//n/sub e/ when E/sub parallel/ > E/su c/ is the Dreicer critical field. The 10 12 cm -3 plasma was collisional with lambda/sub mfp/ < mirror length, had T/sub e/ = T/sub i/ approx. = .2 eV and was found to have Spitzer resistivity when E/sub parallel/ < E/sub c/

  12. Potatoes and Trout: Maintaining Robust Agriculture and a Healthy Trout Fishery in the Central Sands of Wisconsin

    Science.gov (United States)

    Fienen, M. N.; Bradbury, K. R.; Kniffin, M.; Barlow, P. M.; Krause, J.; Westenbroek, S.; Leaf, A.

    2015-12-01

    The well-drained sandy soil in the Wisconsin Central Sands is ideal for growing potatoes, corn, and other vegetables. A shallow sand and gravel aquifer provides abundant water for agricultural irrigation but also supplies critical base flow to cold-water trout streams. These needs compete with one another, and stakeholders from various perspectives are collaborating to seek solutions. Stakeholders were engaged in providing and verifying data to guide construction of a groundwater flow model which was used with linear and sequential linear programming to evaluate optimal tradeoffs between agricultural pumping and ecologically based minimum base flow values. The connection between individual irrigation wells as well as industrial and municipal supply and streamflow depletion can be evaluated using the model. Rather than addressing 1000s of wells individually, a variety of well management groups were established through k-means clustering. These groups are based on location, potential impact, water-use categories, depletion potential, and other factors. Through optimization, pumping rates were reduced to attain mandated minimum base flows. This formalization enables exploration of possible solutions for the stakeholders, and provides a tool which is transparent and forms a basis for discussion and negotiation.

  13. Robotic fabrication in architecture, art and design 2014

    CERN Document Server

    Leon, Monica

    2014-01-01

    Robotic automation has become ubiquitous in the modern manufacturing landscape, spanning an overwhelming range of processes and applications-- from small scale force-controlled grinding operations for orthopedic joints to large scale composite manufacturing of aircraft fuselages. Smart factories, seamlessly linked via industrial networks and sensing, have revolutionized mass production, allowing for intelligent, adaptive manufacturing processes across a broad spectrum of industries. Against this background, an emerging group of researchers, designers, and fabricators have begun to apply robotic technology in the pursuit of architecture, art, and design, implementing them in a range of processes and scales. Coupled with computational design tools the technology is no longer relegated to the repetitive production of the assembly line, and is instead being employed for the mass-customization of non-standard components. This radical shift in protocol has been enabled by the development of new design to production...

  14. Future Manufacturing Systems in Norway – Strategy, Architecture and Framework

    OpenAIRE

    Kolla, Sri Sudha Vijay Keshav

    2016-01-01

    This study investigates the suitability of Cyber Physical Systems (CPS) in Norwegian manufacturing industries and its implementation. This study explores the research and innovation needs in Norway which will be given as inputs to Strategic Research Agenda (SRA) 2030 of European Commission to share future manufacturing strategies in Norway. The objectives of the research are to identifying the opportunities and challenges of CPS, developing a feasible reference architecture of CPS which benef...

  15. High-level language computer architecture

    CERN Document Server

    Chu, Yaohan

    1975-01-01

    High-Level Language Computer Architecture offers a tutorial on high-level language computer architecture, including von Neumann architecture and syntax-oriented architecture as well as direct and indirect execution architecture. Design concepts of Japanese-language data processing systems are discussed, along with the architecture of stack machines and the SYMBOL computer system. The conceptual design of a direct high-level language processor is also described.Comprised of seven chapters, this book first presents a classification of high-level language computer architecture according to the pr

  16. Archive of Geosample Data and Information from the University of Wisconsin Ice Island T3 Core Collection

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — From 1963 to 1972, 349 piston cores were collected from the Arctic Ocean using Ice Island T3 as a sampling platform and sent to the University of Wisconsin-Madison...

  17. Grid Architecture 2

    Energy Technology Data Exchange (ETDEWEB)

    Taft, Jeffrey D. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

    2016-01-01

    The report describes work done on Grid Architecture under the auspices of the Department of Electricity Office of Electricity Delivery and Reliability in 2015. As described in the first Grid Architecture report, the primary purpose of this work is to provide stakeholder insight about grid issues so as to enable superior decision making on their part. Doing this requires the creation of various work products, including oft-times complex diagrams, analyses, and explanations. This report provides architectural insights into several important grid topics and also describes work done to advance the science of Grid Architecture as well.

  18. Towards a semantic web layered architecture

    CSIR Research Space (South Africa)

    Gerber, AJ

    2007-02-01

    Full Text Available as an architectural pattern or architectural style [6, 43]. In this section we give a brief description of the con- cepts software architecture and layered architecture. In ad- dition we provide a summary of a list of criteria for layered architectures identified...- els caused some architectural recurrences to evolve. These are described as architectural patterns [6] or architectural styles [43]. Examples of the best known architectural patterns include, but are not limited to, the client/server architectural...

  19. Frac sand in the United States: a geological and industry overview

    Science.gov (United States)

    Benson, Mary Ellen; Wilson, Anna B.; Bleiwas, Donald I.

    2015-01-01

    A new mineral rush is underway in the upper Midwest of the United States, especially in Wisconsin and Minnesota, for deposits of high-quality frac sand that the mining industry calls “Northern White” sand or “Ottawa” sand. Frac sand is a specialized type of sand that is added to fracking fluids that are injected into unconventional oil and gas wells during hydraulic fracturing (fracking or hydrofracking), a process that enhances petroleum extraction from tight (low permeability) reservoirs. Frac sand consists of natural sand grains with strict mineralogical and textural specifications that act as a proppant (keeping induced fractures open), extending the time of release and the flow rate of hydrocarbons from fractured rock surfaces in contact with the wellbore.

  20. Network Architecture: lessons from the past, vision for the future

    CERN Multimedia

    CERN. Geneva

    2004-01-01

    The Architectural Principles of the Internet have dominated the past decade. Orthogonal to the telecommunications industry principles, they dramatically changed the networking landscape because they relied on iconoclastic ideas. First, the Internet end-to-end principle, which stipulates that the network should intervene minimally on the end-to-end traffic, pushing the complexity to the end-systems. Second, the ban of centralized functions: all the Internet techniques (routing, DNS, management) are based on distributed, decentralized mechanisms. Third, the absolute domination of connectionless (stateless) protocols (as with IP, HTTTP). However, when facing new requirements: multimedia traffic, security, Grid applications, these principles appear sometimes as architectural barriers. Multimedia requires QoS guarantees, but stateless systems are not good at QoS. Security requires active, intelligent networks, but dumb routers or plain end-to-end mail systems are insufficient. Grid applications require...

  1. Information Integration Architecture Development

    OpenAIRE

    Faulkner, Stéphane; Kolp, Manuel; Nguyen, Duy Thai; Coyette, Adrien; Do, Thanh Tung; 16th International Conference on Software Engineering and Knowledge Engineering

    2004-01-01

    Multi-Agent Systems (MAS) architectures are gaining popularity for building open, distributed, and evolving software required by systems such as information integration applications. Unfortunately, despite considerable work in software architecture during the last decade, few research efforts have aimed at truly defining patterns and languages for designing such multiagent architectures. We propose a modern approach based on organizational structures and architectural description lan...

  2. Architectural Contestation

    NARCIS (Netherlands)

    Merle, J.

    2012-01-01

    This dissertation addresses the reductive reading of Georges Bataille's work done within the field of architectural criticism and theory which tends to set aside the fundamental ‘broken’ totality of Bataille's oeuvre and also to narrowly interpret it as a mere critique of architectural form,

  3. Information architecture. Volume 3: Guidance

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-04-01

    The purpose of this document, as presented in Volume 1, The Foundations, is to assist the Department of Energy (DOE) in developing and promulgating information architecture guidance. This guidance is aimed at increasing the development of information architecture as a Departmentwide management best practice. This document describes departmental information architecture principles and minimum design characteristics for systems and infrastructures within the DOE Information Architecture Conceptual Model, and establishes a Departmentwide standards-based architecture program. The publication of this document fulfills the commitment to address guiding principles, promote standard architectural practices, and provide technical guidance. This document guides the transition from the baseline or defacto Departmental architecture through approved information management program plans and budgets to the future vision architecture. This document also represents another major step toward establishing a well-organized, logical foundation for the DOE information architecture.

  4. Software architecture as a set of architectural design decisions

    NARCIS (Netherlands)

    Jansen, Anton; Bosch, Jan; Nord, R; Medvidovic, N; Krikhaar, R; Khrhaar, R; Stafford, J; Bosch, J

    2006-01-01

    Software architectures have high costs for change, are complex, and erode during evolution. We believe these problems are partially due to knowledge vaporization. Currently, almost all the knowledge and information about the design decisions the architecture is based on are implicitly embedded in

  5. Research on networked manufacturing system for reciprocating pump industry

    Science.gov (United States)

    Wu, Yangdong; Qi, Guoning; Xie, Qingsheng; Lu, Yujun

    2005-12-01

    Networked manufacturing is a trend of reciprocating pump industry. According to the enterprises' requirement, the architecture of networked manufacturing system for reciprocating pump industry was proposed, which composed of infrastructure layer, system management layer, application service layer and user layer. Its main functions included product data management, ASP service, business management, and customer relationship management, its physics framework was a multi-tier internet-based model; the concept of ASP service integration was put forward and its process model was also established. As a result, a networked manufacturing system aimed at the characteristics of reciprocating pump industry was built. By implementing this system, reciprocating pump industry can obtain a new way to fully utilize their own resources and enhance the capabilities to respond to the global market quickly.

  6. The architectural design of networks of protein domain architectures.

    Science.gov (United States)

    Hsu, Chia-Hsin; Chen, Chien-Kuo; Hwang, Ming-Jing

    2013-08-23

    Protein domain architectures (PDAs), in which single domains are linked to form multiple-domain proteins, are a major molecular form used by evolution for the diversification of protein functions. However, the design principles of PDAs remain largely uninvestigated. In this study, we constructed networks to connect domain architectures that had grown out from the same single domain for every single domain in the Pfam-A database and found that there are three main distinctive types of these networks, which suggests that evolution can exploit PDAs in three different ways. Further analysis showed that these three different types of PDA networks are each adopted by different types of protein domains, although many networks exhibit the characteristics of more than one of the three types. Our results shed light on nature's blueprint for protein architecture and provide a framework for understanding architectural design from a network perspective.

  7. Deployment and Integration of Industrial Controls The Case of LHC Cryogenics Controls

    CERN Document Server

    Gayet, P

    2003-01-01

    The new cryogenics controls for LHC (UNICOS) are implemented in an open architecture based on SCADA and PLC industrial components, with Ethernet as Fieldnetwork. Its development was outsourced to industry and since mid-2001 several applications have been produced and delivered for refrigerators in the accelerator and experiment domains. This has allowed to validatedetailed performance requirements in terms of communication and distributed architecture. The second phase of this project will involve its integration with the LHC accelerator controls, both at the information exchange level (alarms, data logging) and at the device configuration level. This phase takes advantage of the integrated design at PLC and SCADA level, leading to the use of configuration tools which can be easily connected to the generic device configuration model of the accelerator controls.

  8. Ebola Preparedness Planning and Collaboration by Two Health Systems in Wisconsin, September to December 2014.

    Science.gov (United States)

    Leonhardt, Kathryn Kraft; Keuler, Megan; Safdar, Nasia; Hunter, Paul

    2016-08-01

    We describe the collaborative approach used by 2 health systems in Wisconsin to plan and prepare for the threat of Ebola virus disease. This was a descriptive study of the preparedness planning, infection prevention, and collaboration with public health agencies undertaken by 2 health systems in Wisconsin between September and December 2014. The preparedness approach used by the 2 health systems relied successfully on their robust infrastructure for planning and infection prevention. In the setting of rapidly evolving guidance and unprecedented fear regarding Ebola, the 2 health systems enhanced their response through collaboration and coordination with each other and government public health agencies. Key lessons learned included the importance of a rigorous planning process, robust infection prevention practices, and coalitions between public and private health sectors. The potential threat of Ebola virus disease stimulated emergency preparedness in which acute care facilities played a leading role in the public health response. Leveraging the existing expertise of health systems is essential when faced with emerging infectious diseases. (Disaster Med Public Health Preparedness. 2016;10:691-697).

  9. 77 FR 34125 - Wisconsin Central Ltd.-Intra-Corporate Family Merger Exemption-Elgin, Joliet and Eastern Railway...

    Science.gov (United States)

    2012-06-08

    ... reporting, accounting, IT systems, and corporate filings that are required to support the separate existence... Ltd.--Intra-Corporate Family Merger Exemption-- Elgin, Joliet and Eastern Railway Company Wisconsin... 49 CFR 1180.2(d)(3) for an intra-corporate family transaction. WCL, a rail carrier, is a wholly owned...

  10. The Triumph of Function over Form The Role of Analytic Philosophy in Planning and Analysing Modern Architecture

    Directory of Open Access Journals (Sweden)

    Borbala Jasz

    2017-07-01

    Full Text Available The most dominant dialectical succession of architectural thinking during the 20th Century was between form and function. The latter of these two modern ways of architectural thinking is based on the results of Carnapian Neopositivism. The keywords of this philosophical school, that are empiricism, logic, verification, unity of language and science, could still be applied to interpreting modern architecture. I will explain the antecedents and the first connection between analytic philosophy and architecture, and some characteristic points of their influence during the 20th Century: the triumph of function over form as analogous to triumph of analytic philosophy over metaphysics.After the theoretic grounding of the form-function debate, I am going to focus first on the characteristic appearance of form: the Façadism of Socialist Realism in the architecture of East-Central Europe. Second, I will explain that architectural tendencies of classical modernism did not disappear in this period, they were just hidden in case of public buildings or migrated to the industrial planning. Third, I am going to claim that after this socialist realist gap, the architectural theory and planning tendencies of the interwar period – especially the work of Le Corbusier – returned and continued.

  11. Catalyst Grants: Charged Up: Testing Batteries for CT Scanners | College of

    Science.gov (United States)

    Olympiad Girls Who Code Club FIRST Tech Challenge NSF I-Corps Site of Southeastern Wisconsin UW-Milwaukee multiple industries and building a talent pipeline for companies in Southeastern Wisconsin. Business

  12. SCOS 2: A distributed architecture for ground system control

    Science.gov (United States)

    Keyte, Karl P.

    The current generation of spacecraft ground control systems in use at the European Space Agency/European Space Operations Centre (ESA/ESOC) is based on the SCOS 1. Such systems have become difficult to manage in both functional and financial terms. The next generation of spacecraft is demanding more flexibility in the use, configuration and distribution of control facilities as well as functional requirements capable of matching those being planned for future missions. SCOS 2 is more than a successor to SCOS 1. Many of the shortcomings of the existing system have been carefully analyzed by user and technical communities and a complete redesign was made. Different technologies were used in many areas including hardware platform, network architecture, user interfaces and implementation techniques, methodologies and language. As far as possible a flexible design approach has been made using popular industry standards to provide vendor independence in both hardware and software areas. This paper describes many of the new approaches made in the architectural design of the SCOS 2.

  13. The pedagogy of building solar devices in architecture schools

    Energy Technology Data Exchange (ETDEWEB)

    Lee, T. G. [Calgary Univ., Faculty of Environmental Design, AB (Canada)

    1999-11-01

    Education and training of students of architecture, industrial design, planning and environmental sciences in solar energy utilization, as practiced at the University of Calgary, is described. Classes are relatively small, which allows for considerable flexibility in terms of the different modes of instruction. Lectures, case studies, field trips and workshops all have their place, although the most effective and most popular mode of instruction is the hands-on approach in building and installing a solar heating system. During the course, the students build various types of solar cookers and concentrating solar collectors, including air-type and water-type flat plate collectors. Usually one solar component is built by each class, but previous projects are available for examination and monitoring. This paper elaborates upon the pedagogical basis of shop experience for architectural students. In this context it addresses issues related to shop space, materials, construction, installation testing and monitoring, as well as safety and performance of the student-constructed solar systems. 3 refs., 9 figs.

  14. The pedagogy of building solar devices in architecture schools

    Energy Technology Data Exchange (ETDEWEB)

    Lee, T. G. (Calgary Univ., Faculty of Environmental Design, AB (Canada))

    1999-01-01

    Education and training of students of architecture, industrial design, planning and environmental sciences in solar energy utilization, as practiced at the University of Calgary, is described. Classes are relatively small, which allows for considerable flexibility in terms of the different modes of instruction. Lectures, case studies, field trips and workshops all have their place, although the most effective and most popular mode of instruction is the hands-on approach in building and installing a solar heating system. During the course, the students build various types of solar cookers and concentrating solar collectors, including air-type and water-type flat plate collectors. Usually one solar component is built by each class, but previous projects are available for examination and monitoring. This paper elaborates upon the pedagogical basis of shop experience for architectural students. In this context it addresses issues related to shop space, materials, construction, installation testing and monitoring, as well as safety and performance of the student-constructed solar systems. 3 refs., 9 figs.

  15. Memory architecture

    NARCIS (Netherlands)

    2012-01-01

    A memory architecture is presented. The memory architecture comprises a first memory and a second memory. The first memory has at least a bank with a first width addressable by a single address. The second memory has a plurality of banks of a second width, said banks being addressable by components

  16. Enabling Future Science and Human Exploration with NASA's Next Generation Near Earth and Deep Space Communications and Navigation Architecture

    Science.gov (United States)

    Reinhart, Richard; Schier, James; Israel, David; Tai, Wallace; Liebrecht, Philip; Townes, Stephen

    2017-01-01

    The National Aeronautics and Space Administration (NASA) is studying alternatives for the United States space communications architecture through the 2040 timeframe. This architecture provides communication and navigation services to both human exploration and science missions throughout the solar system. Several of NASA's key space assets are approaching their end of design life and major systems are in need of replacement. The changes envisioned in the relay satellite architecture and capabilities around both Earth and Mars are significant undertakings and occur only once or twice each generation, and therefore is referred to as NASA's next generation space communications architecture. NASA's next generation architecture will benefit from technology and services developed over recent years. These innovations will provide missions with new operations concepts, increased performance, and new business and operating models. Advancements in optical communications will enable high-speed data channels and the use of new and more complex science instruments. Modern multiple beam/multiple access technologies such as those employed on commercial high throughput satellites will enable enhanced capabilities for on-demand service, and with new protocols will help provide Internet-like connectivity for cooperative spacecraft to improve data return and coordinate joint mission objectives. On-board processing with autonomous and cognitive networking will play larger roles to help manage system complexity. Spacecraft and ground systems will coordinate among themselves to establish communications, negotiate link connectivity, and learn to share spectrum to optimize resource allocation. Spacecraft will autonomously navigate, plan trajectories, and handle off-nominal events. NASA intends to leverage the ever-expanding capabilities of the satellite communications industry and foster its continued growth. NASA's technology development will complement and extend commercial capabilities

  17. Enabling Future Science and Human Exploration with NASA's Next Generation near Earth and Deep Space Communications and Navigation Architecture

    Science.gov (United States)

    Reinhart, Richard C.; Schier, James S.; Israel, David J.; Tai, Wallace; Liebrecht, Philip E.; Townes, Stephen A.

    2017-01-01

    The National Aeronautics and Space Administration (NASA) is studying alternatives for the United States space communications architecture through the 2040 timeframe. This architecture provides communication and navigation services to both human exploration and science missions throughout the solar system. Several of NASA's key space assets are approaching their end of design life and major systems are in need of replacement. The changes envisioned in the relay satellite architecture and capabilities around both Earth and Mars are significant undertakings and occur only once or twice each generation, and therefore is referred to as NASA's next generation space communications architecture. NASA's next generation architecture will benefit from technology and services developed over recent years. These innovations will provide missions with new operations concepts, increased performance, and new business and operating models. Advancements in optical communications will enable high-speed data channels and the use of new and more complex science instruments. Modern multiple beam/multiple access technologies such as those employed on commercial high throughput satellites will enable enhanced capabilities for on-demand service, and with new protocols will help provide Internet-like connectivity for cooperative spacecraft to improve data return and coordinate joint mission objectives. On-board processing with autonomous and cognitive networking will play larger roles to help manage system complexity. Spacecraft and ground systems will coordinate among themselves to establish communications, negotiate link connectivity, and learn to share spectrum to optimize resource allocation. Spacecraft will autonomously navigate, plan trajectories, and handle off-nominal events. NASA intends to leverage the ever-expanding capabilities of the satellite communications industry and foster its continued growth. NASA's technology development will complement and extend commercial capabilities

  18. Architectural dimension of sustainability: Re-establishing the concept of recycling

    Directory of Open Access Journals (Sweden)

    Šijaković Milan

    2017-01-01

    Full Text Available Building related processes as water pollution, landfill waste, energy use and related emissions of global warming gases, material and land loss, are undisputable proofs of the devastating effects of the construction industry on our environment. Given that only a small percentage of a total building stock is made out of new work, it is not enough to develop strategies and principles for a sustainable design only for the new projects, but for the existing buildings as well. Therefore, it is essential that, through repurposing, we consider what can be done with what we already have if we are to significantly benefit sustainability agenda in the future. This research focuses on the concept of architectural recycling as a method for achieving sustainable architectural design. In the first place, two concepts, two extremes in dealing with existing buildings will be analysed: 1 preservation as radical stasis and 2 destruction as radical change. This analysis will enable the formulation of the concept of architectural recycling as the ‘preservation through change’, viewed as a sustainable response to rapidly changing conditions. The elaboration of the concept of architectural recycling, as a key method for responding to the sustainability agenda, is the focus of this paper. [Project of the Serbian Ministry of Education, Science and Technological Development, Grant no. TR 36035: Spatial, Environmental, Energy and Social Aspects of Developing Settlements and Climate Change - Mutual Impacts

  19. Towards Horizontal Architecture for Autonomic M2M Service Networks

    Directory of Open Access Journals (Sweden)

    Juhani Latvakoski

    2014-05-01

    Full Text Available Today, increasing number of industrial application cases rely on the Machine to Machine (M2M services exposed from physical devices. Such M2M services enable interaction of physical world with the core processes of company information systems. However, there are grand challenges related to complexity and “vertical silos” limiting the M2M market scale and interoperability. It is here expected that horizontal approach for the system architecture is required for solving these challenges. Therefore, a set of architectural principles and key enablers for the horizontal architecture have been specified in this work. A selected set of key enablers called as autonomic M2M manager, M2M service capabilities, M2M messaging system, M2M gateways towards energy constrained M2M asset devices and creation of trust to enable end-to-end security for M2M applications have been developed. The developed key enablers have been evaluated separately in different scenarios dealing with smart metering, car sharing and electric bike experiments. The evaluation results shows that the provided architectural principles, and developed key enablers establish a solid ground for future research and seem to enable communication between objects and applications, which are not initially been designed to communicate together. The aim as the next step in this research is to create a combined experimental system to evaluate the system interoperability and performance in a more detailed manner.

  20. Can You Hear Architecture

    DEFF Research Database (Denmark)

    Ryhl, Camilla

    2016-01-01

    Taking an off set in the understanding of architectural quality being based on multisensory architecture, the paper aims to discuss the current acoustic discourse in inclusive design and its implications to the integration of inclusive design in architectural discourse and practice as well...... as the understanding of user needs. The paper further points to the need to elaborate and nuance the discourse much more, in order to assure inclusion to the many users living with a hearing impairment or, for other reasons, with a high degree of auditory sensitivity. Using the authors’ own research on inclusive...... design and architectural quality for people with a hearing disability and a newly conducted qualitative evaluation research in Denmark as well as architectural theories on multisensory aspects of architectural experiences, the paper uses examples of existing Nordic building cases to discuss the role...