WorldWideScience

Sample records for wireless networks ieee

  1. Attacks on IEEE 802.11 wireless networks

    Directory of Open Access Journals (Sweden)

    Dejan Milan Tepšić

    2013-06-01

    Full Text Available Security of wireless computer networks was initially secured with the WEP security protocol, which relies on the RC4 encryption algorithm and the CRC algorithm to check the integrity. The basic problems of the WEP are a short initialization vector, unsafe data integrity checking, using a common key, the lack of mechanisms for management and exchange of keys, the lack of protection from the endless insertion of the same package into the network, the lack of authentication of access points and the like. The consequences of these failures are easy attacks against the WEP network, namely their complete insecurity. Therefore, the work began on the IEEE 802.11i protocol, which should radically improve the security of wireless networks. Since the development of a protocol lasted, the WPA standard was released to offset the security gap caused by the WEP. The WPA also relies on RC4 and CRC algorithms, but brings temporary keys and the MIC algorithm for data integrity. The 802.1X authentication was introduced and common keys are no longer needed, since it is possible to use an authentication server. The length of the initialization vector was increased and the vector is obtained based on the packet serial number, in order to prevent the insertion of the same packet into the network. The weakness of the WPA security mechanism is the use of a common key. WPA2 (802.11i later appeared. Unlike the WPA mechanism that worked on old devices with the replacement of software, WPA2 requires new network devices that can perform AES encryption. AES replaces the RC4 algorithm and delivers much greater security. Data integrity is protected by encryption. Despite progress, there are still weaknesses in wireless networks. Attacks for denial of service are possible as well as spoofing package headers attacks. For now, it is not advisable to use wireless networks in environments where unreliability and unavailability are not tolerated. Introduction In the entire history of

  2. Basic security measures for IEEE 802.11 wireless networks

    Directory of Open Access Journals (Sweden)

    Oscar P. Sarmiento

    2008-05-01

    Full Text Available This article presents a tutorial/discussion of three commonly-used IEEE 802.11 wireless network security standards: WEP, WPA and WPA2. A detailed analysis of the RC4 algorithm supporting WEP is presented, including its vulnera-bilities. The WPA and WPA2 encryption protocols’ most relevant aspects and technical characteristics are reviewed for a comparative analysis of the three standards in terms of the security they provide. Special attention has been paid to WEP encryption by using an educational simulation tool written in C++ Builder for facilitating the unders-tanding of this protocol at academic level. Two practical cases of wireless security configurations using Cisco net-working equipment are also presented: configuring and enabling WPA-Personal and WPA2-Personal (these being security options used by TKIP and AES, respectively.

  3. IEEE 802.11s Wireless Mesh Networks: Challenges and Perspectives

    Science.gov (United States)

    Sgora, Aggeliki; Vergados, Dimitris D.; Chatzimisios, Periklis

    A promising solution for wireless environments is the wireless mesh technology that envisages supplementing wired infrastructure with a wireless backbone for providing Internet connectivity to mobile nodes (MNs) or users in residential areas and offices. The IEEE 802.11 TGs has started to work in developing a mesh standard for local area wireless networks. Although a lot of progress has been made and a few new drafts have been released recently, there exist many issues that demand enhanced or even new solutions to 802.11s mesh networking. This paper aims to overview the latest version of the IEEE 802.11s protocol (Draft 2.02), especially the MAC and routing layers, and to point out the challenges that these networks have to overcome in these layers.

  4. Energy-aware path selection metric for IEEE 802.11s wireless mesh networking

    CSIR Research Space (South Africa)

    Mhlanga, MM

    2009-01-01

    Full Text Available The IEEE 802.11s working group has commenced activities, which would lead to the development of a standard for wireless mesh networks (WMNs). The draft of 802.11s introduces a new path selection metric called airtime link metric. However...

  5. Energy-aware path selection metric for IEEE 802.11s wireless mesh networking

    CSIR Research Space (South Africa)

    Mhlanga, MM

    2009-08-01

    Full Text Available The IEEE 802.11s working group has commenced activities, which would lead to the development of a standard for wireless mesh networks (WMNs). The draft of 802.11s introduces a new path selection metric called airtime link metric. However...

  6. Link Investigation of IEEE 802.15.4 Wireless Sensor Networks in Forests.

    Science.gov (United States)

    Ding, Xingjian; Sun, Guodong; Yang, Gaoxiang; Shang, Xinna

    2016-06-27

    Wireless sensor networks are expected to automatically monitor the ecological evolution and wildlife habits in forests. Low-power links (transceivers) are often adopted in wireless sensor network applications, in order to save the precious sensor energy and then achieve long-term, unattended monitoring. Recent research has presented some performance characteristics of such low-power wireless links under laboratory or outdoor scenarios with less obstacles, and they have found that low-power wireless links are unreliable and prone to be affected by the target environment. However, there is still less understanding about how well the low-power wireless link performs in real-world forests and to what extent the complex in-forest surrounding environments affect the link performances. In this paper, we empirically evaluate the low-power links of wireless sensors in three typical different forest environments. Our experiment investigates the performance of the link layer compatible with the IEEE 802.15.4 standard and analyzes the variation patterns of the packet reception ratio (PRR), the received signal strength indicator (RSSI) and the link quality indicator (LQI) under diverse experimental settings. Some observations of this study are inconsistent with or even contradict prior results that are achieved in open fields or relatively clean environments and thus, provide new insights both into effectively evaluating the low-power wireless links and into efficiently deploying wireless sensor network systems in forest environments.

  7. Link Investigation of IEEE 802.15.4 Wireless Sensor Networks in Forests

    Science.gov (United States)

    Ding, Xingjian; Sun, Guodong; Yang, Gaoxiang; Shang, Xinna

    2016-01-01

    Wireless sensor networks are expected to automatically monitor the ecological evolution and wildlife habits in forests. Low-power links (transceivers) are often adopted in wireless sensor network applications, in order to save the precious sensor energy and then achieve long-term, unattended monitoring. Recent research has presented some performance characteristics of such low-power wireless links under laboratory or outdoor scenarios with less obstacles, and they have found that low-power wireless links are unreliable and prone to be affected by the target environment. However, there is still less understanding about how well the low-power wireless link performs in real-world forests and to what extent the complex in-forest surrounding environments affect the link performances. In this paper, we empirically evaluate the low-power links of wireless sensors in three typical different forest environments. Our experiment investigates the performance of the link layer compatible with the IEEE 802.15.4 standard and analyzes the variation patterns of the packet reception ratio (PRR), the received signal strength indicator (RSSI) and the link quality indicator (LQI) under diverse experimental settings. Some observations of this study are inconsistent with or even contradict prior results that are achieved in open fields or relatively clean environments and thus, provide new insights both into effectively evaluating the low-power wireless links and into efficiently deploying wireless sensor network systems in forest environments. PMID:27355957

  8. Energy Consumption Model and Measurement Results for Network Coding-enabled IEEE 802.11 Meshed Wireless Networks

    DEFF Research Database (Denmark)

    Paramanathan, Achuthan; Rasmussen, Ulrik Wilken; Hundebøll, Martin

    2012-01-01

    This paper presents an energy model and energy measurements for network coding enabled wireless meshed networks based on IEEE 802.11 technology. The energy model and the energy measurement testbed is limited to a simple Alice and Bob scenario. For this toy scenario we compare the energy usages...

  9. An empirical evaluation of bufferbloat in IEEE 802.11n wireless networks

    KAUST Repository

    Showail, Ahmad

    2014-04-06

    In this paper, we analyze the impact of large, persistently-full buffers (`bufferbloat\\') on various network dynamics in IEEE 802.11n wireless networks. Bufferbloat has mostly been studied in the context of wired networks. We study the impact of bufferbloat on a variety of wireless network topologies, including wireless LAN (WLAN) and multi-hop wireless networks. Our results show that a single FTP transfer between two Linux wireless hosts can saturate the buffers in the network stack, leading to RTT delays exceeding 4.5 s in multi-hop configurations. We show that well-designed Aggregate MAC Protocol Data Unit (A-MPDU) MAC-layer frame aggregation can reduce RTT delays while simultaneously increasing network throughput. However, additional measures may still be required to meet the constraints of real-time flows (such as VoIP). Our experiments show that large buffers can deteriorate the fairness in rate allocation in parking lot based multi-hop networks.

  10. Estimating Average End-to-End Delays in IEEE 802.11 Multihop Wireless Networks

    OpenAIRE

    Sarr , Cheikh; Guérin-Lassous , Isabelle

    2007-01-01

    In this paper, we present a new analytic model for evaluating average end-to-end delay in IEEE 802.11 multihop wireless networks. Our model gives closed expressions for the end-to-end delay in function of arrivals and service time patterns. Each node is modeled as a M/M/1/K queue from which we can derive expressions for service time via queueing theory. By combining this delay evaluation with different admission controls, we design a protocol called DEAN (Delay Estimation in Ad hoc Networks)....

  11. A Novel IEEE 802.15.4e DSME MAC for Wireless Sensor Networks.

    Science.gov (United States)

    Sahoo, Prasan Kumar; Pattanaik, Sudhir Ranjan; Wu, Shih-Lin

    2017-01-16

    IEEE 802.15.4e standard proposes Deterministic and Synchronous Multichannel Extension (DSME) mode for wireless sensor networks (WSNs) to support industrial, commercial and health care applications. In this paper, a new channel access scheme and beacon scheduling schemes are designed for the IEEE 802.15.4e enabled WSNs in star topology to reduce the network discovery time and energy consumption. In addition, a new dynamic guaranteed retransmission slot allocation scheme is designed for devices with the failure Guaranteed Time Slot (GTS) transmission to reduce the retransmission delay. To evaluate our schemes, analytical models are designed to analyze the performance of WSNs in terms of reliability, delay, throughput and energy consumption. Our schemes are validated with simulation and analytical results and are observed that simulation results well match with the analytical one. The evaluated results of our designed schemes can improve the reliability, throughput, delay, and energy consumptions significantly.

  12. Study on additional carrier sensing for IEEE 802.15.4 wireless sensor networks.

    Science.gov (United States)

    Lee, Bih-Hwang; Lai, Ruei-Lung; Wu, Huai-Kuei; Wong, Chi-Ming

    2010-01-01

    Wireless sensor networks based on the IEEE 802.15.4 standard are able to achieve low-power transmissions in the guise of low-rate and short-distance wireless personal area networks (WPANs). The slotted carrier sense multiple access with collision avoidance (CSMA/CA) is used for contention mechanism. Sensor nodes perform a backoff process as soon as the clear channel assessment (CCA) detects a busy channel. In doing so they may neglect the implicit information of the failed CCA detection and further cause the redundant sensing. The blind backoff process in the slotted CSMA/CA will cause lower channel utilization. This paper proposes an additional carrier sensing (ACS) algorithm based on IEEE 802.15.4 to enhance the carrier sensing mechanism for the original slotted CSMA/CA. An analytical Markov chain model is developed to evaluate the performance of the ACS algorithm. Both analytical and simulation results show that the proposed algorithm performs better than IEEE 802.15.4, which in turn significantly improves throughput, average medium access control (MAC) delay and power consumption of CCA detection.

  13. Study on Additional Carrier Sensing for IEEE 802.15.4 Wireless Sensor Networks

    Directory of Open Access Journals (Sweden)

    Bih-Hwang Lee

    2010-06-01

    Full Text Available Wireless sensor networks based on the IEEE 802.15.4 standard are able to achieve low-power transmissions in the guise of low-rate and short-distance wireless personal area networks (WPANs. The slotted carrier sense multiple access with collision avoidance (CSMA/CA is used for contention mechanism. Sensor nodes perform a backoff process as soon as the clear channel assessment (CCA detects a busy channel. In doing so they may neglect the implicit information of the failed CCA detection and further cause the redundant sensing. The blind backoff process in the slotted CSMA/CA will cause lower channel utilization. This paper proposes an additional carrier sensing (ACS algorithm based on IEEE 802.15.4 to enhance the carrier sensing mechanism for the original slotted CSMA/CA. An analytical Markov chain model is developed to evaluate the performance of the ACS algorithm. Both analytical and simulation results show that the proposed algorithm performs better than IEEE 802.15.4, which in turn significantly improves throughput, average medium access control (MAC delay and power consumption of CCA detection.

  14. On the Feasibility of Wireless Multimedia Sensor Networks over IEEE 802.15.5 Mesh Topologies

    Directory of Open Access Journals (Sweden)

    Antonio-Javier Garcia-Sanchez

    2016-05-01

    Full Text Available Wireless Multimedia Sensor Networks (WMSNs are a special type of Wireless Sensor Network (WSN where large amounts of multimedia data are transmitted over networks composed of low power devices. Hierarchical routing protocols typically used in WSNs for multi-path communication tend to overload nodes located within radio communication range of the data collection unit or data sink. The battery life of these nodes is therefore reduced considerably, requiring frequent battery replacement work to extend the operational life of the WSN system. In a wireless sensor network with mesh topology, any node may act as a forwarder node, thereby enabling multiple routing paths toward any other node or collection unit. In addition, mesh topologies have proven advantages, such as data transmission reliability, network robustness against node failures, and potential reduction in energy consumption. This work studies the feasibility of implementing WMSNs in mesh topologies and their limitations by means of exhaustive computer simulation experiments. To this end, a module developed for the Synchronous Energy Saving (SES mode of the IEEE 802.15.5 mesh standard has been integrated with multimedia tools to thoroughly test video sequences encoded using H.264 in mesh networks.

  15. On the Feasibility of Wireless Multimedia Sensor Networks over IEEE 802.15.5 Mesh Topologies.

    Science.gov (United States)

    Garcia-Sanchez, Antonio-Javier; Losilla, Fernando; Rodenas-Herraiz, David; Cruz-Martinez, Felipe; Garcia-Sanchez, Felipe

    2016-05-05

    Wireless Multimedia Sensor Networks (WMSNs) are a special type of Wireless Sensor Network (WSN) where large amounts of multimedia data are transmitted over networks composed of low power devices. Hierarchical routing protocols typically used in WSNs for multi-path communication tend to overload nodes located within radio communication range of the data collection unit or data sink. The battery life of these nodes is therefore reduced considerably, requiring frequent battery replacement work to extend the operational life of the WSN system. In a wireless sensor network with mesh topology, any node may act as a forwarder node, thereby enabling multiple routing paths toward any other node or collection unit. In addition, mesh topologies have proven advantages, such as data transmission reliability, network robustness against node failures, and potential reduction in energy consumption. This work studies the feasibility of implementing WMSNs in mesh topologies and their limitations by means of exhaustive computer simulation experiments. To this end, a module developed for the Synchronous Energy Saving (SES) mode of the IEEE 802.15.5 mesh standard has been integrated with multimedia tools to thoroughly test video sequences encoded using H.264 in mesh networks.

  16. Energy Harvesting - Wireless Sensor Networks for Indoors Applications Using IEEE 802.11

    DEFF Research Database (Denmark)

    Fafoutis, Xenofon; Sørensen, Thomas; Madsen, Jan

    2014-01-01

    The paper investigates the feasibility of using IEEE 802.11 in energy harvesting low-power sensing applications. The investigation is based on a prototype carbon dioxide sensor node that is powered by artificial indoors light. The wireless communication module of the sensor node is based on the RTX......4100 module. RTX4100 incorporates a wireless protocol that duty-cycles the radio while being compatible with IEEE 802.11 access points. The presented experiments demonstrate sustainable operation but indicate a trade-off between the benefits of using IEEE 802.11 in energy harvesting applications...

  17. Strategies for Optimal MAC Parameters Tuning in IEEE 802.15.6 Wearable Wireless Sensor Networks.

    Science.gov (United States)

    Alam, Muhammad Mahtab; Ben Hamida, Elyes

    2015-09-01

    Wireless body area networks (WBAN) has penetrated immensely in revolutionizing the classical heath-care system. Recently, number of WBAN applications has emerged which introduce potential limits to existing solutions. In particular, IEEE 802.15.6 standard has provided great flexibility, provisions and capabilities to deal emerging applications. In this paper, we investigate the application-specific throughput analysis by fine-tuning the physical (PHY) and medium access control (MAC) parameters of the IEEE 802.15.6 standard. Based on PHY characterizations in narrow band, at the MAC layer, carrier sense multiple access collision avoidance (CSMA/CA) and scheduled access protocols are extensively analyzed. It is concluded that, IEEE 802.15.6 standard can satisfy most of the WBANs applications throughput requirements by maximum achieving 680 Kbps. However, those emerging applications which require high quality audio or video transmissions, standard is not able to meet their constraints. Moreover, delay, energy efficiency and successful packet reception are considered as key performance metrics for comparing the MAC protocols. CSMA/CA protocol provides the best results to meet the delay constraints of medical and non-medical WBAN applications. Whereas, the scheduled access approach, performs very well both in energy efficiency and packet reception ratio.

  18. Efficient Beacon Collision Resolution Procedure for IEEE 802.15.4 /Zigbee Wireless Personal Area Networks

    Directory of Open Access Journals (Sweden)

    Bassam A. Zafar

    2017-04-01

    Full Text Available While IEEE 802.15.4/Zigbee is a promising technology for Wireless Personal Area Networks, several transmission problems are not yet resolved. In particular, the problem of beacon transmission interferences is causing the device connection loss to the network. In order to resolve this problem, we present a new distributed and reactive procedure for beacon collision resolution. It is an extension of the alignment procedure to reorganize randomly the beacon transmission time when a collision has occurred. The detail of the proposed procedure will be fully described and analyzed. The performance of our approach is performed by simulations. The results show that our approach reduces the collision probability and the device disconnections consequently.

  19. Mathematical modeling of a radio-frequency path for IEEE 802.11ah based wireless sensor networks

    Science.gov (United States)

    Tyshchenko, Igor; Cherepanov, Alexander; Dmitrii, Vakhnin; Popova, Mariia

    2017-09-01

    This article discusses the process of creating the mathematical model of a radio-frequency path for an IEEE 802.11ah based wireless sensor networks using M atLab Simulink CAD tools. In addition, it describes occurring perturbing effects and determining the presence of a useful signal in the received mixture.

  20. Subjective Audio Quality over a Secure IEEE 802.11n Draft 2.0 Wireless Local Area Network

    Science.gov (United States)

    2009-03-01

    generated by a G.711 codec and transmission over an IEEE 802.11n draft 2.0 wireless local area network (WLAN). Decline in audio quality due to additional...6 2.5 Real-Time Transport Protocol ...................................................................................8 2.6 Audio Codecs ...Page 1. VoIP Audio Codec Data Rates and Typical MOS

  1. A Study of IEEE 802.15.4 Security Framework for Wireless Body Area Networks

    Directory of Open Access Journals (Sweden)

    Kyung Sup Kwak

    2011-01-01

    Full Text Available A Wireless Body Area Network (WBAN is a collection of low-power and lightweight wireless sensor nodes that are used to monitor the human body functions and the surrounding environment. It supports a number of innovative and interesting applications, including ubiquitous healthcare and Consumer Electronics (CE applications. Since WBAN nodes are used to collect sensitive (life-critical information and may operate in hostile environments, they require strict security mechanisms to prevent malicious interaction with the system. In this paper, we first highlight major security requirements and Denial of Service (DoS attacks in WBAN at Physical, Medium Access Control (MAC, Network, and Transport layers. Then we discuss the IEEE 802.15.4 security framework and identify the security vulnerabilities and major attacks in the context of WBAN. Different types of attacks on the Contention Access Period (CAP and Contention Free Period (CFP parts of the superframe are analyzed and discussed. It is observed that a smart attacker can successfully corrupt an increasing number of GTS slots in the CFP period and can considerably affect the Quality of Service (QoS in WBAN (since most of the data is carried in CFP period. As we increase the number of smart attackers the corrupted GTS slots are eventually increased, which prevents the legitimate nodes to utilize the bandwidth efficiently. This means that the direct adaptation of IEEE 802.15.4 security framework for WBAN is not totally secure for certain WBAN applications. New solutions are required to integrate high level security in WBAN.

  2. A study of IEEE 802.15.4 security framework for wireless body area networks.

    Science.gov (United States)

    Saleem, Shahnaz; Ullah, Sana; Kwak, Kyung Sup

    2011-01-01

    A Wireless Body Area Network (WBAN) is a collection of low-power and lightweight wireless sensor nodes that are used to monitor the human body functions and the surrounding environment. It supports a number of innovative and interesting applications, including ubiquitous healthcare and Consumer Electronics (CE) applications. Since WBAN nodes are used to collect sensitive (life-critical) information and may operate in hostile environments, they require strict security mechanisms to prevent malicious interaction with the system. In this paper, we first highlight major security requirements and Denial of Service (DoS) attacks in WBAN at Physical, Medium Access Control (MAC), Network, and Transport layers. Then we discuss the IEEE 802.15.4 security framework and identify the security vulnerabilities and major attacks in the context of WBAN. Different types of attacks on the Contention Access Period (CAP) and Contention Free Period (CFP) parts of the superframe are analyzed and discussed. It is observed that a smart attacker can successfully corrupt an increasing number of GTS slots in the CFP period and can considerably affect the Quality of Service (QoS) in WBAN (since most of the data is carried in CFP period). As we increase the number of smart attackers the corrupted GTS slots are eventually increased, which prevents the legitimate nodes to utilize the bandwidth efficiently. This means that the direct adaptation of IEEE 802.15.4 security framework for WBAN is not totally secure for certain WBAN applications. New solutions are required to integrate high level security in WBAN.

  3. Multiple Power-Saving MSSs Scheduling Methods for IEEE802.16e Broadband Wireless Networks

    Science.gov (United States)

    2014-01-01

    This work proposes two enhanced multiple mobile subscriber stations (MSSs) power-saving scheduling methods for IEEE802.16e broadband wireless networks. The proposed methods are designed for the Unsolicited Grant Service (UGS) of IEEE802.16e. To reduce the active periods of all power-saving MSSs, the base station (BS) allocates each MSS fewest possible transmission frames to retrieve its data from the BS. The BS interlaces the active periods of each MSS to increase the amount of scheduled MSSs and splits the overflowing transmission frames to maximize the bandwidth utilization. Simulation results reveal that interlacing the active periods of MSSs can increase the number of scheduled MSSs to more than four times of that in the Direct scheduling method. The bandwidth utilization can thus be improved by 60%–70%. Splitting the overflowing transmission frames can improve bandwidth utilization by more than 10% over that achieved using the method of interlacing active periods, with a sacrifice of only 1% of the sleep periods in the interlacing active period method. PMID:24523656

  4. Multiple Power-Saving MSSs Scheduling Methods for IEEE802.16e Broadband Wireless Networks

    Directory of Open Access Journals (Sweden)

    Shih-Chang Huang

    2014-01-01

    Full Text Available This work proposes two enhanced multiple mobile subscriber stations (MSSs power-saving scheduling methods for IEEE802.16e broadband wireless networks. The proposed methods are designed for the Unsolicited Grant Service (UGS of IEEE802.16e. To reduce the active periods of all power-saving MSSs, the base station (BS allocates each MSS fewest possible transmission frames to retrieve its data from the BS. The BS interlaces the active periods of each MSS to increase the amount of scheduled MSSs and splits the overflowing transmission frames to maximize the bandwidth utilization. Simulation results reveal that interlacing the active periods of MSSs can increase the number of scheduled MSSs to more than four times of that in the Direct scheduling method. The bandwidth utilization can thus be improved by 60%–70%. Splitting the overflowing transmission frames can improve bandwidth utilization by more than 10% over that achieved using the method of interlacing active periods, with a sacrifice of only 1% of the sleep periods in the interlacing active period method.

  5. An Analysis of Network and Sensor Performance Within IEEE 802.X Wireless MESH Networks in the Tactical Network Topology (TNT)

    National Research Council Canada - National Science Library

    Davis, Joseph A., Sr

    2005-01-01

    ....x wireless MESH networks within a DoD Tactical network environment. Multiple sensor configurations operating with wireless MESH network technologies will be researched and analyzed for performance in expeditionary environment situations...

  6. Design of Cyberwar Laboratory Exercises to Implement Common Security Attacks against IEEE 802.11 Wireless Networks

    Directory of Open Access Journals (Sweden)

    Mina Malekzadeh

    2010-01-01

    Full Text Available In wireless network communications, radio waves travel through free space; hence, the information reaches any receiving point with appropriate radio receivers. This aspect makes the wireless networks vulnerable to various types of attacks. A true understanding of these attacks provides better ability to defend the network against the attacks, thus eliminating potential threats from the wireless systems. This work presents a series of cyberwar laboratory exercises that are designed for IEEE 802.11 wireless networks security courses. The exercises expose different aspects of violations in security such as confidentiality, privacy, availability, and integrity. The types of attacks include traffic analysis, rogue access point, MAC filtering, replay, man-in-the-middle, and denial of service attacks. For each exercise, the materials are presented as open-source tools along with descriptions of the respective methods, procedures, and penetration techniques.

  7. Achievable Throughput-Based MAC Layer Handoff in IEEE 802.11 Wireless Local Area Networks

    Directory of Open Access Journals (Sweden)

    Wu Haitao

    2009-01-01

    Full Text Available We propose a MAC layer handoff mechanism for IEEE 802.11 Wireless Local Area Networks (WLAN to give benefit to bandwidth-greedy applications at STAs. The proposed mechanism determines an optimal AP with the maximum achievable throughput rather than the best signal condition by estimating the AP's bandwidth with a new on-the-fly measurement method, Transient Frame Capture (TFC, and predicting the actual throughput could be achieved at STAs. Since the TFC is employed based on the promiscuous mode of WLAN NIC, STAs can avoid the service degradation through the current associated AP. In addition, the proposed mechanism is a client-only solution which does not require any modification of network protocol on APs. To evaluate the performance of the proposed mechanism, we develop an analytic model to estimate reliable and accurate bandwidth of the AP and demonstrate through testbed measurement with various experimental study methods. We also validate the fairness of the proposed mechanism through simulation studies.

  8. Fuzzy logic congestion control in IEEE 802.11 wireless local area networks: A performance evaluation

    CSIR Research Space (South Africa)

    Nyirenda, CN

    2007-09-01

    Full Text Available In 802.11 Wireless Local Area Networks, the wired and the wireless interfaces of the Access Point are characterized by the disparity in channel capacity. This presents a significant bottleneck for traffic flowing from the wired network...

  9. Energy optimization based path selection algorithm for IEEE 802.11s wireless mesh networks

    CSIR Research Space (South Africa)

    Mhlanga, MM

    2011-09-01

    Full Text Available It is everyone’s dream to have network connectivity anywhere at all times. This dream can only be realized provided there are feasible solutions that are put in place for the next generation of wireless works. Wireless Mesh Networks (WMNs...

  10. WING/WORLD: An Open Experimental Toolkit for the Design and Deployment of IEEE 802.11-Based Wireless Mesh Networks Testbeds

    Directory of Open Access Journals (Sweden)

    Riggio Roberto

    2010-01-01

    Full Text Available Wireless Mesh Networks represent an interesting instance of light-infrastructure wireless networks. Due to their flexibility and resiliency to network failures, wireless mesh networks are particularly suitable for incremental and rapid deployments of wireless access networks in both metropolitan and rural areas. This paper illustrates the design and development of an open toolkit aimed at supporting the design of different solutions for wireless mesh networking by enabling real evaluation, validation, and demonstration. The resulting testbed is based on off-the-shelf hardware components and open-source software and is focused on IEEE 802.11 commodity devices. The software toolkit is based on an "open" philosophy and aims at providing the scientific community with a tool for effective and reproducible performance analysis of WMNs. The paper describes the architecture of the toolkit, and its core functionalities, as well as its potential evolutions.

  11. WING/WORLD: An Open Experimental Toolkit for the Design and Deployment of IEEE 802.11-Based Wireless Mesh Networks Testbeds

    Directory of Open Access Journals (Sweden)

    Daniele Miorandi

    2010-01-01

    Full Text Available Wireless Mesh Networks represent an interesting instance of light-infrastructure wireless networks. Due to their flexibility and resiliency to network failures, wireless mesh networks are particularly suitable for incremental and rapid deployments of wireless access networks in both metropolitan and rural areas. This paper illustrates the design and development of an open toolkit aimed at supporting the design of different solutions for wireless mesh networking by enabling real evaluation, validation, and demonstration. The resulting testbed is based on off-the-shelf hardware components and open-source software and is focused on IEEE 802.11 commodity devices. The software toolkit is based on an “open” philosophy and aims at providing the scientific community with a tool for effective and reproducible performance analysis of WMNs. The paper describes the architecture of the toolkit, and its core functionalities, as well as its potential evolutions.

  12. Simple Adaptive Single Differential Coherence Detection of BPSK Signals in IEEE 802.15.4 Wireless Sensor Networks.

    Science.gov (United States)

    Zhang, Gaoyuan; Wen, Hong; Wang, Longye; Xie, Ping; Song, Liang; Tang, Jie; Liao, Runfa

    2017-12-26

    In this paper, we propose an adaptive single differential coherent detection (SDCD) scheme for the binary phase shift keying (BPSK) signals in IEEE 802.15.4 Wireless Sensor Networks (WSNs). In particular, the residual carrier frequency offset effect (CFOE) for differential detection is adaptively estimated, with only linear operation, according to the changing channel conditions. It was found that the carrier frequency offset (CFO) and chip signal-to-noise ratio (SNR) conditions do not need a priori knowledge. This partly benefits from that the combination of the trigonometric approximation sin - 1 ( x ) ≈ x and a useful assumption, namely, the asymptotic or high chip SNR, is considered for simplification of the full estimation scheme. Simulation results demonstrate that the proposed algorithm can achieve an accurate estimation and the detection performance can completely meet the requirement of the IEEE 802.15.4 standard, although with a little loss of reliability and robustness as compared with the conventional optimal single-symbol detector.

  13. IEEE 802.15.4 ZigBee-Based Time-of-Arrival Estimation for Wireless Sensor Networks.

    Science.gov (United States)

    Cheon, Jeonghyeon; Hwang, Hyunsu; Kim, Dongsun; Jung, Yunho

    2016-02-05

    Precise time-of-arrival (TOA) estimation is one of the most important techniques in RF-based positioning systems that use wireless sensor networks (WSNs). Because the accuracy of TOA estimation is proportional to the RF signal bandwidth, using broad bandwidth is the most fundamental approach for achieving higher accuracy. Hence, ultra-wide-band (UWB) systems with a bandwidth of 500 MHz are commonly used. However, wireless systems with broad bandwidth suffer from the disadvantages of high complexity and high power consumption. Therefore, it is difficult to employ such systems in various WSN applications. In this paper, we present a precise time-of-arrival (TOA) estimation algorithm using an IEEE 802.15.4 ZigBee system with a narrow bandwidth of 2 MHz. In order to overcome the lack of bandwidth, the proposed algorithm estimates the fractional TOA within the sampling interval. Simulation results show that the proposed TOA estimation algorithm provides an accuracy of 0.5 m at a signal-to-noise ratio (SNR) of 8 dB and achieves an SNR gain of 5 dB as compared with the existing algorithm. In addition, experimental results indicate that the proposed algorithm provides accurate TOA estimation in a real indoor environment.

  14. Design of handoff procedures for broadband wireless access IEEE 802.16 based networks

    Directory of Open Access Journals (Sweden)

    V. Rangel–Licea

    2008-01-01

    Full Text Available IEEE 802.16 is a protocol for fixed broad band wire less access that is currently trying to add mobility among mobile users in the standard. However, mobility adds some technical barriers that should be solved first, this is the case of HO "handoff" (change of connection between two base stations "BS" by a mobile user. In this paper, the problem of HO in IEEE 802.16 is approached try ing to maintain the quality of service (QoS of mobile users. A mechanism for changing connection during HO is pre sented. A simulation model based on OPNET MODELER1 was developed to evaluate the performance of the proposed HO mechanism. Finally, this paper demonstrates that it is possible to implement a seam less HO mech a nism over IEEE 802.16 even for users with de manding applications such as voice over IP.

  15. Cross-Layer Measurement on an IEEE 802.11g Wireless Network Supporting MPEG-2 Video Streaming Applications in the Presence of Interference

    Directory of Open Access Journals (Sweden)

    Alessandro Sona

    2010-01-01

    Full Text Available The performance of wireless local area networks supporting video streaming applications, based on MPEG-2 video codec, in the presence of interference is here dealt with. IEEE 802.11g standard wireless networks, that do not support QoS in according with IEEE 802.11e standard, are, in particular, accounted for and Bluetooth signals, additive white Gaussian noise, and competitive data traffic are considered as sources of interference. The goal is twofold: from one side, experimentally assessing and correlating the values that some performance metrics assume at the same time at different layers of an IEEE 802.11g WLAN delivering video streaming in the presence of in-channel interference; from the other side, deducing helpful and practical hints for designers and technicians, in order to efficiently assess and enhance the performance of an IEEE 802.11g WLAN supporting video streaming in some suitable setup conditions and in the presence of interference. To this purpose, an experimental analysis is planned following a cross-layer measurement approach, and a proper testbed within a semianechoic chamber is used. Valuable results are obtained in terms of signal-to-interference ratio, packet loss ratio, jitter, video quality, and interference data rate; helpful hints for designers and technicians are finally gained.

  16. A Green Media Access Method for IEEE 802.15.6 Wireless Body Area Network.

    Science.gov (United States)

    Jacob, Anil K; Jacob, Lillykutty

    2017-09-30

    It is of utmost importance to conserve battery energy to the maximum possible extent in WBAN nodes while collecting and transferring medical data. The IEEE 802.15.6 WBAN standard does not specify any method to conserve energy. This paper focuses on a method to conserve energy in IEEE 802.15.6 WBAN nodes when using CSMA/CA, while simultaneously restricting data delivery delay to the required value as specified in medical applications. The technique is to allow the nodes to sleep all the times except for receiving beacons and for transmitting data frames whenever a data frame enters an empty buffer. The energy consumed by the nodes and the average latency of data frame for periodical arrival of data are found out analytically. The analytical results are validated and also the proposed method is compared with other energy conserving schemes, using Castalia simulation studies. The proposed method shows superior performance in both device lifetime and latency of emergency medical data.

  17. Distributed Spatial Interference Coordination for IEEE 802.11n Wireless Networks

    Science.gov (United States)

    Chen, Rui; Li, Changle; Li, Jiandong

    The 802.11n networks with MIMO technique provide a spatial degree of freedom for dealing with co-channel interference. In this letter, our proposed spatial interference coordination scheme is achieved by distributed precoding for the downlink and distributed multi-user detection for the uplink. Simulation results validate the proposed scheme in terms of the downlink and uplink maximum achievable rates at each AP.

  18. Wireless Networks: New Meaning to Ubiquitous Computing.

    Science.gov (United States)

    Drew, Wilfred, Jr.

    2003-01-01

    Discusses the use of wireless technology in academic libraries. Topics include wireless networks; standards (IEEE 802.11); wired versus wireless; why libraries implement wireless technology; wireless local area networks (WLANs); WLAN security; examples of wireless use at Indiana State University and Morrisville College (New York); and useful…

  19. Neural network-based multiuser detection for SDMA-OFDM system over IEEE 802.11n indoor wireless local area network channel models

    Science.gov (United States)

    Praveen Bagadi, Kala; Das, Susmita

    2013-10-01

    Space division multiple access - orthogonal frequency division multiplexing-based wireless communication has the potential to offer high-spectral efficiency, system performance and capacity. This article proposes an efficient blind multiuser detection (MUD) scheme using artificial neural network models such as the radial basis function. The proposed MUD technique is consistently outperforming the existing minimum mean square error and minimum bit error rate (MBER) MUDs with the performance close to the optimal maximum likelihood (ML) detector. Besides that, the computational complexity of the proposed one is comparatively lower than both the MBER and ML detectors. Further, it can also outperform MBER MUD in the overload scenario, where the number of users is more than that of the number of receiving antennas simulation-based study showing BER performance and complexity are carried out to prove the efficiency of the proposed techniques. This analysis is carried through the IEEE 802.11n standard channel models, which are designed for indoor wireless local area network applications of bandwidth up to 100 MHz at frequencies 2 and 5 GHz.

  20. Deadline-Aware Scheduling Perspectives in Industrial Wireless Networks: A Comparison between IEEE 802.15.4 and Bluetooth

    OpenAIRE

    Collotta, Mario; Pau, Giovanni; Scatà, Gianfranco

    2013-01-01

    In industrial contexts, most of process control applications use wired communication networks. The reliability of wired networks is indisputable and extensively demonstrated by several studies in the literature. However, it is important to consider several disadvantages provided by the use of wired technologies, like high deployment and maintenance costs and low network scalability. Although it is difficult to fully replace wired networks, wireless communication protocols have features which ...

  1. Time of Arrival Based on Chirp Pulses as a means to Perform Localization in IEEE 802.15.4a Wireless Sensor Networks

    Directory of Open Access Journals (Sweden)

    NAUWELAERS, B.

    2010-05-01

    Full Text Available This paper introduces the technology Time of Arrival (TOA based on chirp pulses (according to IEEE 802.15.4a as a means to perform localization in Wireless Sensor Networks (WSN's active at 2.4 GHz. Advantages and disadvantages of the technology are discussed and act as a guideline for improving localization accuracy. Tests concerning TOA are performed by means of the location engine of Nanotron. Adapting this engine leads to improved localization results. It is shown that TOA measurements are susceptible to reflections and dynamic environments.

  2. Fluid-flow modeling of a relay node in an IEEE 802.11 wireless ad-hoc network

    NARCIS (Netherlands)

    Roijers, F.; Berg, J.L. van den; Mandjes, M.

    2007-01-01

    Wireless ad-hoc networks are based on shared medium technology where the nodes arrange access to the medium in a distributed way independent of their current traffic demand. This has the inherent drawback that a node that serves as a relay node for transmissions of multiple neighboring nodes is

  3. New Solutions Based On Wireless Networks For Dynamic Traffic Lights Management: A Comparison Between IEEE 802.15.4 And Bluetooth

    Directory of Open Access Journals (Sweden)

    Collotta Mario

    2015-09-01

    Full Text Available The Wireless Sensor Networks are widely used to detect and exchange information and in recent years they have been increasingly involved in Intelligent Transportation System applications, especially in dynamic management of signalized intersections. In fact, the real-time knowledge of information concerning traffic light junctions represents a valid solution to congestion problems. In this paper, a wireless network architecture, based on IEEE 802.15.4 or Bluetooth, in order to monitor vehicular traffic flows near to traffic lights, is introduced. Moreover, an innovative algorithm is proposed in order to determine dynamically green times and phase sequence of traffic lights, based on measured values of traffic flows. Several simulations compare IEEE 802.15.4 and Bluetooth protocols in order to identify the more suitable communication protocol for ITS applications. Furthermore, in order to confirm the validity of the proposed algorithm for the dynamic management of traffic lights, some case studies have been considered and several simulations have been performed.

  4. An Improved Approach for RSSI-Based only Calibration-Free Real-Time Indoor Localization on IEEE 802.11 and 802.15.4 Wireless Networks

    Directory of Open Access Journals (Sweden)

    Marco Passafiume

    2017-03-01

    Full Text Available Assuming a reliable and responsive spatial contextualization service is a must-have in IEEE 802.11 and 802.15.4 wireless networks, a suitable approach consists of the implementation of localization capabilities, as an additional application layer to the communication protocol stack. Considering the applicative scenario where satellite-based positioning applications are denied, such as indoor environments, and excluding data packet arrivals time measurements due to lack of time resolution, received signal strength indicator (RSSI measurements, obtained according to IEEE 802.11 and 802.15.4 data access technologies, are the unique data sources suitable for indoor geo-referencing using COTS devices. In the existing literature, many RSSI based localization systems are introduced and experimentally validated, nevertheless they require periodic calibrations and significant information fusion from different sensors that dramatically decrease overall systems reliability and their effective availability. This motivates the work presented in this paper, which introduces an approach for an RSSI-based calibration-free and real-time indoor localization. While switched-beam array-based hardware (compliant with IEEE 802.15.4 router functionality has already been presented by the author, the focus of this paper is the creation of an algorithmic layer for use with the pre-existing hardware capable to enable full localization and data contextualization over a standard 802.15.4 wireless sensor network using only RSSI information without the need of lengthy offline calibration phase. System validation reports the localization results in a typical indoor site, where the system has shown high accuracy, leading to a sub-metrical overall mean error and an almost 100% site coverage within 1 m localization error.

  5. An Improved Approach for RSSI-Based only Calibration-Free Real-Time Indoor Localization on IEEE 802.11 and 802.15.4 Wireless Networks.

    Science.gov (United States)

    Passafiume, Marco; Maddio, Stefano; Cidronali, Alessandro

    2017-03-29

    Assuming a reliable and responsive spatial contextualization service is a must-have in IEEE 802.11 and 802.15.4 wireless networks, a suitable approach consists of the implementation of localization capabilities, as an additional application layer to the communication protocol stack. Considering the applicative scenario where satellite-based positioning applications are denied, such as indoor environments, and excluding data packet arrivals time measurements due to lack of time resolution, received signal strength indicator (RSSI) measurements, obtained according to IEEE 802.11 and 802.15.4 data access technologies, are the unique data sources suitable for indoor geo-referencing using COTS devices. In the existing literature, many RSSI based localization systems are introduced and experimentally validated, nevertheless they require periodic calibrations and significant information fusion from different sensors that dramatically decrease overall systems reliability and their effective availability. This motivates the work presented in this paper, which introduces an approach for an RSSI-based calibration-free and real-time indoor localization. While switched-beam array-based hardware (compliant with IEEE 802.15.4 router functionality) has already been presented by the author, the focus of this paper is the creation of an algorithmic layer for use with the pre-existing hardware capable to enable full localization and data contextualization over a standard 802.15.4 wireless sensor network using only RSSI information without the need of lengthy offline calibration phase. System validation reports the localization results in a typical indoor site, where the system has shown high accuracy, leading to a sub-metrical overall mean error and an almost 100% site coverage within 1 m localization error.

  6. Introducing an Adaptive Method to Tune Initial Backoff Window ( -ATM in IEEE 802.11 Wireless Networks

    Directory of Open Access Journals (Sweden)

    Tadayon Navid

    2010-01-01

    Full Text Available IEEE802.11 access protocol uses CSMA/CA in its Medium Access control layer as the main access function, which carries several deficiencies. In these networks, as the number of active stations increases, delay and throughput degrade severely. As far as throughput and service delay are vital elements in Quality of Service (QoS determination, such degradation could lead to intolerable situations and reduce the efficiency of WLANs. Networks (WLANs. Studies proved this problem arises due to constant initial backoff windows size ( , which is an important parameter in determination of network behavior. In this paper, we introduce a new method to tune this parameter adaptively according to changes in channel load. In this method, we do tune this parameter after every transmission using a feedback from transmission channel. Later it will be proven that applying this method in MAC layer enhances network stability; delay trend in all traffic classes exhibits a considerable reduction when compared with simple Enhanced Distributed Coordination Access (EDCA scenarios. Also throughput exhibits a salient improvement in level. In other word, QoS improves. Especially, with the aid of this method, delay variations in all decrease considerably and more smoothen delay trends are achieved.

  7. Resource management in wireless networking

    CERN Document Server

    Cardei, Mihaela; Du, Ding-Zhu

    2005-01-01

    This is the first book that provides readers with a deep technical overview of recent advances in resource management for wireless networks at different layers of the protocol stack. The subject is explored in various wireless networks, such as ad hoc wireless networks, 3G/4G cellular, IEEE 802.11, and Bluetooth personal area networks.Survey chapters give an excellent introduction to key topics in resource management for wireless networks, while experts will be satisfied by the technical depth of the knowledge imparted in chapters exploring hot research topics.The subject area discussed in this book is very relevant today, considering the recent remarkable growth of wireless networking and the convergence of wireless personal communications, internet technologies and real-time multimedia.This volume is a very good companion for practitioners working on implementing solutions for multimedia and Quality of Service - sensitive applications over wireless networks.Written for:Researchers, faculty members, students...

  8. Tactical Wireless Networking in Coalition Environments: Implementing an IEEE 802.20 Wireless End-User Network Utilizing FLASH-OFDM to Provide a Secure Mobile Extension to Existing WAN

    National Research Council Canada - National Science Library

    Parrish, William J; Tovar, Daniel R

    2005-01-01

    This thesis will focus on the area of 802.20 wireless networking as a feasible "last mile" solution to wireless access in a tactical coalition environment and will be implemented into a series of experiments...

  9. A Location-Based Duplex Scheme for Cost Effective Rural Broadband Connectivity Using IEEE 802.22 Cognitive Radio Based Wireless Regional Area Networks

    Science.gov (United States)

    Kalidoss, R.; Bhagyaveni, M. A.; Vishvaksenan, K. S.

    2014-08-01

    The search for a method of utilizing the scarce spectrum in an efficient manner is an active area of research in both academic and industrial communities. IEEE 802.22 is a standard for wireless regional area network (WRAN) based on cognitive radio (CR) that operates over underutilized portions of TV bands (54-862 MHz). Time division duplex (TDD)-based WRAN cells have such advantages as dynamic traffic allocation, traffic asymmetry to users and ease of spectrum allocation. However, these cells suffer from severe cross time slot (CTS) interference when the frames of the cells are not synchronized with adjacent WRAN cells. In this paper, we evaluate the location-based duplex (LBD) scheme for eliminating the CTS interference. The proposed LBD system is much more flexible and efficient in providing asymmetric data service and eliminating CTS interference by exploiting the advantages of both TDD and frequency division duplex (FDD) schemes. We also compare the performance of LBD systems with virtual cell concepts. Furthermore, our simulation results reveal that LBD-based systems outperform the virtual cell approach in terms of the low signal-to-interference (SIR) ratio requirement by mitigating the effects of CTS.

  10. Throughput modeling of the IEEE MAC for sensor networks

    NARCIS (Netherlands)

    M. Onderwater (Martijn); G.J. Hoekstra (Gerard); R.D. van der Mei (Rob)

    2017-01-01

    textabstractIn this paper we provide a model for analyzing the saturation throughput of the ieee 802.15.4 mac protocol, which is the de-facto standard for wireless sensor networks, ensuring fair access to the channel. To this end, we introduce the concept of a natural layer, which reflects the time

  11. Reliable Communication in Wireless Meshed Networks using Network Coding

    DEFF Research Database (Denmark)

    Pahlevani, Peyman; Paramanathan, Achuthan; Hundebøll, Martin

    2012-01-01

    The advantages of network coding have been extensively studied in the field of wireless networks. Integrating network coding with existing IEEE 802.11 MAC layer is a challenging problem. The IEEE 802.11 MAC does not provide any reliability mechanisms for overheard packets. This paper addresses...

  12. An Analysis of the Feasibility and Applicability of IEEE 802.x Wireless Mesh Networks within the Global Information Grid

    Science.gov (United States)

    2004-09-01

    switches through CAT5 Ethernet cable. These switches are then connected through CAT5 cable to 15 Foundry switches operating at the network “borders...70 WAPs, 35 Foundry switches, 15 Foundry switches (borders), 70 Cat5e Ethernet runs from WAPs to switches, 35 Cat5e Ethernet runs from switches to...Last Accessed 13 September 2004. Griffith, Eric. “Tropos: Supplier of Metro Wi-Fi.” Wi-Fi Planet (May 21, 2003). Available from http://www.wi

  13. An Analysis of Electromagnetic Interference (EMI) of Ultra Wideband(UWB) and IEEE 802.11A Wireless Local Area Network (WLAN) Employing Orthogonal Frequency Division Multiplexing (OFDM)

    Science.gov (United States)

    2004-03-01

    be monitored with an electronic monitoring device that records the ambient temperature periodically. The data is collected and logged daily...Fi) Networking Handbook, McGraw-Hill: NY, 2003. [Sal02]. M.P. Salud , Investigation of RF Emissions from Wireless Networks as a Threat to Avionic

  14. A Forensic Readiness Model for Wireless Networks

    OpenAIRE

    Ngobeni, Sipho; Venter, Hein; Burke, Ivan

    2010-01-01

    International audience; Over the past decade, wireless mobile communications technology based on IEEE 802.11 wireless local area networks (WLANs) has been adopted worldwide on a massive scale. However, as the number of wireless users has soared, so has the possibility of cyber crime, where criminals deliberately and actively break into WLANs with the intent to cause harm or access sensitive information. WLAN digital forensics is seen not only as a response to cyber crime in wireless environme...

  15. A Reliable Data Transmission Model for IEEE 802.15.4e Enabled Wireless Sensor Network under WiFi Interference.

    Science.gov (United States)

    Sahoo, Prasan Kumar; Pattanaik, Sudhir Ranjan; Wu, Shih-Lin

    2017-06-07

    The IEEE 802.15.4e standard proposes Medium Access Control (MAC) to support collision-free wireless channel access mechanisms for industrial, commercial and healthcare applications. However, unnecessary wastage of energy and bandwidth consumption occur due to inefficient backoff management and collisions. In this paper, a new channel access mechanism is designed for the buffer constraint sensor devices to reduce the packet drop rate, energy consumption and collisions. In order to avoid collision due to the hidden terminal problem, a new frame structure is designed for the data transmission. A new superframe structure is proposed to mitigate the problems due to WiFi and ZigBee interference. A modified superframe structure with a new retransmission opportunity for failure devices is proposed to reduce the collisions and retransmission delay with high reliability. Performance evaluation and validation of our scheme indicate that the packet drop rate, throughput, reliability, energy consumption and average delay of the nodes can be improved significantly.

  16. THE INFLUENCE OF MAC BUFFER ON THE CONTENTION-BASED ACCESS SCHEME WITH BURSTING OPTION FOR IEEE 802.11E WIRELESS NETWORKS

    Directory of Open Access Journals (Sweden)

    S. SELVAKENNEDY

    2006-12-01

    Full Text Available Wireless LANs are increasingly being used for inelastic applications. Currently, there is little support for quality of service in the IEEE 802.11 MAC protocol, and IEEE task group E has defined the 802.11e MAC extension. Enhanced distributed channel access (EDCA is a contention-based scheme of the 802.11e standard. To allow a station to transmit more than one frame from a single contention, an optional feature known as controlled frame-bursting (CFB is introduced in the standard. In this paper, we initially performed an average analysis to determine a suitable burst duration limit. Then, a detailed evaluation and comparison of the EDCA protocol with the CFB option is carried out through simulation to quantify its performance gain. The impact of the MAC transmit buffer size is also incorporated. Accordingly, we have proposed a suitable approach to guide the configuration of the burst duration limit. It is demonstrated that an optimized CFB configuration allows the MAC protocol to achieve 30% more capacity than the basic EDCA scheme.

  17. Extending Service Area of IEEE 802.11 Ad Hoc Networks

    Science.gov (United States)

    Choi, Woo-Yong

    2012-06-01

    According to the current IEEE 802.11 wireless LAN standards, IEEE 802.11 ad hoc networks have the limitation that all STAs (Stations) are in the one-hop transmission range of each other. In this paper, to alleviate the limitation of IEEE 802.11 ad hoc networks we propose the efficient method for selecting the most appropriate pseudo AP (Access Point) from among the set of ad hoc STAs and extending the service area of IEEE 802.11 ad hoc networks by the pseudo AP's relaying the internal traffic of IEEE 802.11 ad hoc networks. Numerical examples show that the proposed method significantly extends the service area of IEEE 802.11 ad hoc networks.

  18. Wireless Network Penetration Testing and Security Auditing

    Directory of Open Access Journals (Sweden)

    Wang Shao-Long

    2016-01-01

    Full Text Available IEEE802.11 wireless wireless networks have security issues that are vulnerable to a variety of attacks. Due to using radio to transport data, attackers can bypass firewalls, sniff sensitive information, intercept packets and send malicious packets. Security auditing and penetration testing is expected to ensure wireless networks security. The contributions of this work are analyzed the vulnerability and types of attacks pertaining to IEEE 802.11 WLAN, performed well known attacks in a laboratory environment to conduct penetration tests to confirm whether our wireless network is hackable or not. WAIDPS is configured as auditing tool to view wireless attacks, such as WEP/WPA/WPA2 cracking, rouge access points, denial of service attack. WAIDPS is designed to detect wireless intrusion with additional features. Penetration testing and auditing will mitigate the risk and threatening to protect WALN.

  19. Delay Analysis of GTS Bridging between IEEE 802.15.4 and IEEE 802.11 Networks for Healthcare Applications.

    Science.gov (United States)

    Misić, Jelena; Sherman Shen, Xuemin

    2009-01-01

    We consider interconnection of IEEE 802.15.4 beacon-enabled network cluster with IEEE 802.11b network. This scenario is important in healthcare applications where IEEE 802.15.4 nodes comprise patient's body area network (BAN) and are involved in sensing some health-related data. BAN nodes have very short communication range in order to avoid harming patient's health and save energy. Sensed data needs to be transmitted to an access point in the ward room using wireless technology with higher transmission range and rate such as IEEE 802.11b. We model the interconnected network where IEEE 802.15.4-based BAN operates in guaranteed time slot (GTS) mode, and IEEE 802.11b part of the bridge conveys GTS superframe to the 802.11b access point. We then analyze the network delays. Performance analysis is performed using EKG traffic from continuous telemetry, and we discuss the delays of communication due the increasing number of patients.

  20. A Reliable Data Transmission Model for IEEE 802.15.4e Enabled Wireless Sensor Network under WiFi Interference

    Directory of Open Access Journals (Sweden)

    Prasan Kumar Sahoo

    2017-06-01

    Full Text Available The IEEE 802.15.4e standard proposes Medium Access Control (MAC to support collision-free wireless channel access mechanisms for industrial, commercial and healthcare applications. However, unnecessary wastage of energy and bandwidth consumption occur due to inefficient backoff management and collisions. In this paper, a new channel access mechanism is designed for the buffer constraint sensor devices to reduce the packet drop rate, energy consumption and collisions. In order to avoid collision due to the hidden terminal problem, a new frame structure is designed for the data transmission. A new superframe structure is proposed to mitigate the problems due to WiFi and ZigBee interference. A modified superframe structure with a new retransmission opportunity for failure devices is proposed to reduce the collisions and retransmission delay with high reliability. Performance evaluation and validation of our scheme indicate that the packet drop rate, throughput, reliability, energy consumption and average delay of the nodes can be improved significantly.

  1. Routing in Wireless Multimedia Home Networks

    NARCIS (Netherlands)

    Scholten, Johan; Jansen, P.G.; Hop, Laurens

    This paper describes an adapted version of the destination sequenced distance vector routing protocol (DSDV) which is suitable to calculate routes in a wireless ¿real-time¿ home network. The home network is based on a IEEE 802.11b ad hoc network and uses a scheduled token to enforce real-time

  2. Routing in Wireless Multimedia Home Networks

    NARCIS (Netherlands)

    Scholten, Johan; Jansen, P.G.; Hop, Laurens

    This paper describes an adapted version of the destination sequenced distance vector routing protocol (DSDV) which is suitable to calculate routes in a wireless real-time home network. The home network is based on a IEEE 802.11b ad hoc network and uses a scheduled token to enforce real-time

  3. Wireless local area network. A new technology of network

    International Nuclear Information System (INIS)

    Wu Yunjun; Zhao Zongtao

    2003-01-01

    This paper introduces Wireless Local Area Network (WLAN), including the concept, history, characters and the foreground of its development, it also narrates in detail the several key techniques used to implement IEEE802.11 WLAN, and ideas on key technology of future progress in wireless LAN field have also been presented. (authors)

  4. DAWN: Dynamic Ad-hoc Wireless Network

    Science.gov (United States)

    2016-06-19

    Wireless Network 1 Introduction The network-centric battlefield includes sensors, troop carriers, unmanned air vehicle (UAV), aircraft, smart ...Bellman Control Heritage Award. • Honorary Doctorate at Technical University of Crete. • Best paper award at 2008 IEEE International Conference on Mobile Ad-hoc and Sensor Systems.

  5. Probabilistic Bandwidth Assignment in Wireless Sensor Networks

    OpenAIRE

    Khan , Dawood; Nefzi , Bilel; Santinelli , Luca; Song , Ye-Qiong

    2012-01-01

    International audience; With this paper we offer an insight in designing and analyzing wireless sensor networks in a versatile manner. Our framework applies probabilistic and component-based design principles for the wireless sensor network modeling and consequently analysis; while maintaining flexibility and accuracy. In particular, we address the problem of allocating and reconfiguring the available bandwidth. The framework has been successfully implemented in IEEE 802.15.4 using an Admissi...

  6. IEEE 802.11-Based Wireless Sensor System for Vibration Measurement

    Directory of Open Access Journals (Sweden)

    Yutaka Uchimura

    2010-01-01

    Full Text Available Network-based wireless sensing has become an important area of research and various new applications for remote sensing are expected to emerge. One of the promising applications is structural health monitoring of building or civil engineering structure and it often requires vibration measurement. For the vibration measurement via wireless network, time synchronization is indispensable. In this paper, we introduce a newly developed time synchronized wireless sensor network system. The system employs IEEE 802.11 standard-based TSF-counter and sends the measured data with the counter value. TSF based synchronization enables consistency on common clock among different wireless nodes. We consider the scale effect on synchronization accuracy and evaluated the effect by taking beacon collisions into account. The scalability issue by numerical simulations is also studied. This paper also introduces a newly developed wireless sensing system and the hardware and software specifications are introduced. The experiments were conducted in a reinforced concrete building to evaluate synchronization accuracy. The developed system was also applied for a vibration measurement of a 22-story steel structured high rise building. The experimental results showed that the system performed more than sufficiently.

  7. IEEE 802.11 Wireless LANs: Performance Analysis and Protocol Refinement

    Directory of Open Access Journals (Sweden)

    Chatzimisios P.

    2005-01-01

    Full Text Available The IEEE 802.11 protocol is emerging as a widely used standard and has become the most mature technology for wireless local area networks (WLANs. In this paper, we focus on the tuning of the IEEE 802.11 protocol parameters taking into consideration, in addition to throughput efficiency, performance metrics such as the average packet delay, the probability of a packet being discarded when it reaches the maximum retransmission limit, the average time to drop a packet, and the packet interarrival time. We present an analysis, which has been validated by simulation that is based on a Markov chain model commonly used in the literature. We further study the improvement on these performance metrics by employing suitable protocol parameters according to the specific communication needs of the IEEE 802.11 protocol for both basic access and RTS/CTS access schemes. We show that the use of a higher initial contention window size does not considerably degrade performance in small networks and performs significantly better in any other scenario. Moreover, we conclude that the combination of a lower maximum contention window size and a higher retry limit considerably improves performance. Results indicate that the appropriate adjustment of the protocol parameters enhances performance and improves the services that the IEEE 802.11 protocol provides to various communication applications.

  8. A forensic readiness model for Wireless Local Area Networks

    CSIR Research Space (South Africa)

    Ngobeni, S

    2010-01-01

    Full Text Available Over the past decade, wireless mobile communications technology based on IEEE 802.11 wireless local area networks (WLANs) has been adopted worldwide on a massive scale. However, as the number of wireless users has soared, so has the possibility...

  9. Latency and Jitter Analysis for IEEE 802.11e Wireless LANs

    Directory of Open Access Journals (Sweden)

    Sungkwan Youm

    2013-01-01

    Full Text Available This paper presents a numerical analysis of latency and jitter for IEEE 802.11e wireless local area networks (WLANs in a saturation condition, by using a Markov model. We use this model to explicate how the enhanced distributed coordination function (EDCF differentiates classes of service and to characterize the probability distribution of the medium access control (MAC layer packet latency and jitter, on which the quality of the voice over Internet protocol (VoIP calls is dependent. From the proposed analytic model, we can estimate the available number of nodes determining the system performance, in order to satisfy user demands on the latency and jitter.

  10. Corrections to "Connectivity-Based Reliable Multicast MAC Protocol for IEEE 802.11 Wireless LANs"

    Directory of Open Access Journals (Sweden)

    Choi Woo-Yong

    2010-01-01

    Full Text Available We have found the errors in the throughput formulae presented in our paper "Connectivity-based reliable multicast MAC protocol for IEEE 802.11 wireless LANs". We provide the corrected formulae and numerical results.

  11. The Exploration of Network Coding in IEEE 802.15.4 Networks

    Directory of Open Access Journals (Sweden)

    Deze Zeng

    2011-01-01

    communication protocol should be energy efficient. The IEEE 802.15.4 is designed as a standard protocol for low power, low data rate, low complexity, and short range connections in WPANs. The standard supports allocating several numbers of collision-free guarantee time slots (GTSs within a superframe for some time-critical transmissions. Recently, COPE was proposed as a promising network coding architecture to essentially improve the throughput of wireless networks. In this paper, we exploit the network coding technique at coordinators to improve energy efficiency of the WPAN. Some related practical issues, such as GTS allocation and multicast, are also discussed in order to exploit the network coding opportunities efficiently. Since the coding opportunities are mostly exploited, our proposal achieves both higher energy efficiency and throughput performance than the original IEEE 802.15.4.

  12. Wireless mesh networks

    CERN Document Server

    Held, Gilbert

    2005-01-01

    Wireless mesh networking is a new technology that has the potential to revolutionize how we access the Internet and communicate with co-workers and friends. Wireless Mesh Networks examines the concept and explores its advantages over existing technologies. This book explores existing and future applications, and examines how some of the networking protocols operate.The text offers a detailed analysis of the significant problems affecting wireless mesh networking, including network scale issues, security, and radio frequency interference, and suggests actual and potential solutions for each pro

  13. Security for multihop wireless networks

    CERN Document Server

    Khan, Shafiullah

    2014-01-01

    Security for Multihop Wireless Networks provides broad coverage of the security issues facing multihop wireless networks. Presenting the work of a different group of expert contributors in each chapter, it explores security in mobile ad hoc networks, wireless sensor networks, wireless mesh networks, and personal area networks.Detailing technologies and processes that can help you secure your wireless networks, the book covers cryptographic coprocessors, encryption, authentication, key management, attacks and countermeasures, secure routing, secure medium access control, intrusion detection, ep

  14. Cooperative Technique Based on Sensor Selection in Wireless Sensor Network

    OpenAIRE

    ISLAM, M. R.; KIM, J.

    2009-01-01

    An energy efficient cooperative technique is proposed for the IEEE 1451 based Wireless Sensor Networks. Selected numbers of Wireless Transducer Interface Modules (WTIMs) are used to form a Multiple Input Single Output (MISO) structure wirelessly connected with a Network Capable Application Processor (NCAP). Energy efficiency and delay of the proposed architecture are derived for different combination of cluster size and selected number of WTIMs. Optimized constellation parameters are used for...

  15. Green heterogeneous wireless networks

    CERN Document Server

    Ismail, Muhammad; Nee, Hans-Peter; Qaraqe, Khalid A; Serpedin, Erchin

    2016-01-01

    This book focuses on the emerging research topic "green (energy efficient) wireless networks" which has drawn huge attention recently from both academia and industry. This topic is highly motivated due to important environmental, financial, and quality-of-experience (QoE) considerations. Specifically, the high energy consumption of the wireless networks manifests in approximately 2% of all CO2 emissions worldwide. This book presents the authors’ visions and solutions for deployment of energy efficient (green) heterogeneous wireless communication networks. The book consists of three major parts. The first part provides an introduction to the "green networks" concept, the second part targets the green multi-homing resource allocation problem, and the third chapter presents a novel deployment of device-to-device (D2D) communications and its successful integration in Heterogeneous Networks (HetNets). The book is novel in that it specifically targets green networking in a heterogeneous wireless medium, which re...

  16. A Cross-Layer Key Management Scheme for MIPv6 Fast Handover over IEEE 802.11 Wireless LAN

    Directory of Open Access Journals (Sweden)

    Chang-Seop Park

    2015-01-01

    Full Text Available A new key management and security scheme is proposed to integrate Layer Two (L2 and Layer Three (L3 keys for secure and fast Mobile IPv6 handover over IEEE 802.11 Wireless Local Area Network (WLAN. Unlike the original IEEE 802.11-based Mobile IPv6 Fast Handover (FMIPv6 that requires time-consuming IEEE 802.1x-based Extensible Authentication Protocol (EAP authentication on each L3 handover, the newly proposed key management and security scheme requires only one 802.1x-EAP regardless of how many L3 handovers occur. Therefore, the proposed scheme reduces the handover latency that results from a lengthy 802.1x-based EAP. The proposed key management and security scheme is extensively analyzed in terms of security and performance, and the proposed security scheme is shown to be more secure than those that were previously proposed.

  17. Application for Measurement in Wireless Sensor Networks

    Directory of Open Access Journals (Sweden)

    Miroslav MAHDAL

    2009-06-01

    Full Text Available This paper deals with wireless sensor networks, which are based on IEEE 802.15.4 standard. The development kit from Jennic company was used for wireless measuring of values and for creation of sensor network. For this purposes the sensor boards with wireless modules with marking JN5139 were used. These boards provide sensors (sensor of temperature, relative humidity and light sensor but also another interface, which helps to develop applications. Modules are programmed in Integrated Development Environment (IDE, which integrates C function library and C++ compiler and linker. The visualization application was created for monitoring of wireless sensor network. There is the possibility of local and wireless measurement. For creation of this application the SCADA/HMI system, Control Web 5 was used. This SCADA/HMI system enables to communicate with all wireless modules through base station (network's coordinator. The application also enables initialisation and network setting the any wireless module communicating with the base station. The advantage is the remote configuration and control of network. The application also enables the gathering, converting, viewing and archiving of incoming data from particular modules.

  18. Link quality and path based clustering in IEEE 802.15.4-2015 TSCH networks

    OpenAIRE

    Mavromatis, Alexandros; Papadopoulos, Georgios; Fafoutis, Xenofon; Goulianos, Angelos; Oikonomou, George; Chatzimisios, Periklis; Tryfonas, Theo

    2017-01-01

    Advance clustering techniques have been widely used in Wireless Sensor Networks (WSNs) since they can potentially reduce latency, improve scheduling, decrease end-to-end delay and optimise energy consumption within a dense network topology. In this paper, we present a novel clustering algorithm for high density IEEE 802.15.4-2015 Time-Slotted Channel Hopping (TSCH). In particular, the proposed methodology merges a variety of solutions into an integrated clustering design. Assuming an homogene...

  19. Wireless rechargeable sensor networks

    CERN Document Server

    Yang, Yuanyuan

    2015-01-01

    This SpringerBrief provides a concise guide to applying wireless energy transfer techniques in traditional battery-powered sensor networks. It examines the benefits and challenges of wireless power including efficiency and reliability. The authors build a wireless rechargeable sensor networks from scratch and aim to provide perpetual network operation. Chapters cover a wide range of topics from the collection of energy information and recharge scheduling to joint design with typical sensing applications such as data gathering. Problems are approached using a natural combination of probability

  20. Wireless network pricing

    CERN Document Server

    Huang, Jianwei

    2013-01-01

    Today's wireless communications and networking practices are tightly coupled with economic considerations, to the extent that it is almost impossible to make a sound technology choice without understanding the corresponding economic implications. This book aims at providing a foundational introduction on how microeconomics, and pricing theory in particular, can help us to understand and build better wireless networks. The book can be used as lecture notes for a course in the field of network economics, or a reference book for wireless engineers and applied economists to understand how pricing

  1. Fiber wireless networks

    Science.gov (United States)

    Nirmalathas, A.; Bakaul, M.; Lim, C.; Novak, D.; Waterhouse, R.

    2005-11-01

    Broadband wireless networks based on a number of new frequency windows at higher microwave and millimeter-wave frequencies have been actively pursued to provide ultra-high bandwidth services over a wireless networks. These networks will have a large number of antenna base-stations with high throughput. Significant reductions in antenna base-station complexity can be achieved if most of the signal routing and switching functions centralized at a central office in the network. In such a network, fiber feed networks can be effectively deployed to provide high bandwidth interconnections between multiple antenna base-stations and the central office. With wavelength division multiplexing, efficient optical fiber feed network architectures could be realised to provide interconnection to a large number of antenna base-stations. In this paper, we present an over view of our recent research into system technologies for fiber wireless networks.

  2. High Throughput Tactical Wireless Networking for Surveillance and Targeting in a Coalition Environment: An Analysis of the Next Generation IEEE 802.11n Equipment and Standard

    National Research Council Canada - National Science Library

    Thomason, Gary W

    2005-01-01

    ...). This thesis also provides a brief introduction to COASTS, its support for testing various networking schemes, and their effectiveness in supplying information necessary to reach a decision maker's desired end-state...

  3. Intrusion detection and monitoring for wireless networks.

    Energy Technology Data Exchange (ETDEWEB)

    Thomas, Eric D.; Van Randwyk, Jamie A.; Lee, Erik J.; Stephano, Amanda (Indiana University); Tabriz, Parisa (University of Illinois at Urbana-Champaign); Pelon, Kristen (Cedarville University); McCoy, Damon (University of Colorado, Boulder); Lodato, Mark (Lafayette College); Hemingway, Franklin (University of New Mexico); Custer, Ryan P.; Averin, Dimitry (Polytechnic University); Franklin, Jason (Carnegie Mellon University); Kilman, Dominique Marie

    2005-11-01

    Wireless computer networks are increasing exponentially around the world. They are being implemented in both the unlicensed radio frequency (RF) spectrum (IEEE 802.11a/b/g) and the licensed spectrum (e.g., Firetide [1] and Motorola Canopy [2]). Wireless networks operating in the unlicensed spectrum are by far the most popular wireless computer networks in existence. The open (i.e., proprietary) nature of the IEEE 802.11 protocols and the availability of ''free'' RF spectrum have encouraged many producers of enterprise and common off-the-shelf (COTS) computer networking equipment to jump into the wireless arena. Competition between these companies has driven down the price of 802.11 wireless networking equipment and has improved user experiences with such equipment. The end result has been an increased adoption of the equipment by businesses and consumers, the establishment of the Wi-Fi Alliance [3], and widespread use of the Alliance's ''Wi-Fi'' moniker to describe these networks. Consumers use 802.11 equipment at home to reduce the burden of running wires in existing construction, facilitate the sharing of broadband Internet services with roommates or neighbors, and increase their range of ''connectedness''. Private businesses and government entities (at all levels) are deploying wireless networks to reduce wiring costs, increase employee mobility, enable non-employees to access the Internet, and create an added revenue stream to their existing business models (coffee houses, airports, hotels, etc.). Municipalities (Philadelphia; San Francisco; Grand Haven, MI) are deploying wireless networks so they can bring broadband Internet access to places lacking such access; offer limited-speed broadband access to impoverished communities; offer broadband in places, such as marinas and state parks, that are passed over by traditional broadband providers; and provide themselves with higher quality, more

  4. Wireless Networks Security

    OpenAIRE

    Jenko, Marko

    2016-01-01

    In this thesis we deal with security, penetration testing and different types of attacks on wireless networks. We theoretically familiarize with the field of wireless networks, security mechanisms and the most used security standards. Then we systematically overview the field of penetration testing. We divide the penetration testing on types and different methodologies. We explain the tasks of the provider and the subscriber in penetration testing. Description of the process of conducting the...

  5. Enhancing MAC performance of DCF protocol for IEEE 802.11 wireless LANs

    Science.gov (United States)

    Choi, Woo-Yong

    2017-01-01

    The DCF (Distributed Coordination Function) is the basic MAC (Medium Access Control) protocol of IEEE 802.11 wireless LANs and compatible with various IEEE 802.11 PHY extensions. The performance of the DCF degrades exponentially as the number of nodes participating in the DCF transmission procedure increases. To deal with this problem, we propose a simple, however efficient modification of the DCF by which the performance of the DCF is greatly enhanced.

  6. Networking wireless sensors

    National Research Council Canada - National Science Library

    Krishnamachari, Bhaskar

    2005-01-01

    ... by networking techniques across multiple layers. The topics covered include network deployment, localization, time synchronization, wireless radio characteristics, medium-access, topology control, routing, data-centric techniques, and transport protocols. Ideal for researchers and designers seeking to create new algorithms and protocols and enginee...

  7. Wireless networked music performance

    CERN Document Server

    Gabrielli, Leonardo

    2016-01-01

    This book presents a comprehensive overview of the state of the art in Networked Music Performance (NMP) and a historical survey of computer music networking. It introduces current technical trends in NMP and technical issues yet to be addressed. It also lists wireless communication protocols and compares these to the requirements of NMP. Practical use cases and advancements are also discussed.

  8. Subsurface Wireless Sensor Networks

    Science.gov (United States)

    Niemeier, J. J.; Davies, J. L.; Kruger, A.

    2008-12-01

    Conventional thinking holds that underground- and underwater radio communication is not possible, except at very low frequencies employing very long antennas and high transmit power. However, researchers at The University of Iowa have demonstrated that using inexpensive, low-power radios, it is in fact possible to achieve reliable underground radio communication over distances of several meters. This allows for creating underground wireless sensor networks. A proof-of-concept network was established at The University of Iowa, where nodes that measure soil moisture content are buried over a 20×20 m area (up to 1 m deep). The nodes organize themselves into a wireless sensor network, reconfigure routes as radio link quality waxes and wanes, cooperate in routing data packets to a surface base station, and so on. In an agricultural research setting, an advantage of such buried wireless sensor networks is that, if nodes were buried deep enough, they may be left in place during agricultural field work. Power consumption is an important issue in wireless sensor networks. This is especially true in a buried network where battery replacement is a major undertaking. The focus of continuing research is developing methods of inductively recharging buried sensor batteries.

  9. IEEE 802.11 Networks: A Simple Model Geared Towards Offloading Studies and Considerations on Future Small Cells

    DEFF Research Database (Denmark)

    Garcia, Luis Guilherme Uzeda; Rodriguez, Ignacio; Catania, Davide

    2013-01-01

    WiFi is the prevalent wireless access technology in local area deployments and is expected to play a major role in a mobile operator’s data offloading strategy. As a result, having simple tools that are able to assess the offloading potential of IEEE 802.11 networks is vital. In this paper, we...

  10. Insecurity of Wireless Networks

    Energy Technology Data Exchange (ETDEWEB)

    Sheldon, Frederick T [ORNL; Weber, John Mark [Dynetics, Inc.; Yoo, Seong-Moo [University of Alabama, Huntsville; Pan, W. David [University of Alabama, Huntsville

    2012-01-01

    Wireless is a powerful core technology enabling our global digital infrastructure. Wi-Fi networks are susceptible to attacks on Wired Equivalency Privacy, Wi-Fi Protected Access (WPA), and WPA2. These attack signatures can be profiled into a system that defends against such attacks on the basis of their inherent characteristics. Wi-Fi is the standard protocol for wireless networks used extensively in US critical infrastructures. Since the Wired Equivalency Privacy (WEP) security protocol was broken, the Wi-Fi Protected Access (WPA) protocol has been considered the secure alternative compatible with hardware developed for WEP. However, in November 2008, researchers developed an attack on WPA, allowing forgery of Address Resolution Protocol (ARP) packets. Subsequent enhancements have enabled ARP poisoning, cryptosystem denial of service, and man-in-the-middle attacks. Open source systems and methods (OSSM) have long been used to secure networks against such attacks. This article reviews OSSMs and the results of experimental attacks on WPA. These experiments re-created current attacks in a laboratory setting, recording both wired and wireless traffic. The article discusses methods of intrusion detection and prevention in the context of cyber physical protection of critical Internet infrastructure. The basis for this research is a specialized (and undoubtedly incomplete) taxonomy of Wi-Fi attacks and their adaptations to existing countermeasures and protocol revisions. Ultimately, this article aims to provide a clearer picture of how and why wireless protection protocols and encryption must achieve a more scientific basis for detecting and preventing such attacks.

  11. A Novel Prioritization Scheme to Improve QoS in IEEE 802.11e Networks

    Directory of Open Access Journals (Sweden)

    Navid Tadayon

    2010-01-01

    Full Text Available IEEE 802.11 WLAN utilizes a distributed function at its MAC layer, namely, DCF to access the wireless medium. Due to its distributed nature, DCF is able to guarantee working stability in a wireless medium while maintaining the assembling and maintenance cost in a low level. However, DCF is inefficient in dealing with real-time traffics due to its incapability on providing QoS. IEEE 802.11e was introduced as a supplementary standard to cope with this problem. This standard introduces an Enhanced Distributed Coordination Function (EDCF that works based on diff-Serve model and can serve multiple classes of traffics (by using different prioritizations schemes. With the emergence of new time-sensitive applications, EDCF has proved to be yet inefficient in dealing with these kinds of traffics because it could not provide network with well-differentiated QoS. In this study, we propose a novel prioritization scheme to improve QoS level in IEEE 802.11e network. In this scheme, we replace Uniform PDF with Gamma PDF, which has salient differentiating properties. We investigate the suitability and superiority of this scheme on furnishing network with well-differentiated QoS using probabilistic analysis. We strengthen our claims by extensive simulation runs.

  12. SELF-POWERED WIRELESS SENSOR NODE POWER MODELING BASED ON IEEE 802.11 COMMUNICATION PROTOCOL

    Energy Technology Data Exchange (ETDEWEB)

    Vivek Agarwal; Raymond A. DeCarlo; Lefteri H. Tsoukalas

    2016-04-01

    Design and technical advancements in sensing, processing, and wireless communication capabilities of small, portable devices known as wireless sensor nodes (WSNs) have drawn extensive research attention and are vastly applied in science and engineering applications. The WSNs are typically powered by a chemical battery source that has a load dependent finite lifetime. Most applications, including the nuclear industry applications, require WSNs to operate for an extended period of time beginning with their deployment. To ensure longevity, it is important to develop self-powered WSNs. The benefit of self-powered WSNs goes far beyond the cost savings of removing the need for cable installation and maintenance. Self-powered WSNs will potentially offer significant expansion in remote monitoring of nuclear facilities, and provide important data on plant equipment and component status during normal operation, as well as in case of abnormal operation, station blackouts or post-accident evaluation. Advancements in power harvesting technologies enable electric energy generation from many sources, including kinetic, thermal, and radiated energy. For the ongoing research at Idaho National Laboratory, a solid-state thermoelectric-based technology, the thermoelectric generator (TEG), is used to convert thermal energy to power a WSN. The design and development of TEGs to power WSNs that would remain active for a long period of time requires comprehensive understanding of WSN operational. This motivates the research in modeling the lifetime, i.e., power consumption, of a WSN by taking into consideration various node and network level activities. A WSN must perform three essential tasks: sense events, perform quick local information processing of sensed events, and wirelessly exchange locally processed data with the base station or with other WSNs in the network. Each task has a power cost per unit tine and an additional cost when switching between tasks. There are number of other

  13. CLUSTER BASED TIME DIVISION MULTIPLE ACCESS SCHEDULING SCHEME FOR ZIGBEE WIRELESS SENSOR NETWORKS

    OpenAIRE

    P. Anandhakumar; B. Meenakshi

    2012-01-01

    In IEEE 802.15.4 ZigBee Wireless Sensor Networks, an efficient scheduling mechanism is required for reliable data transmission. Further, concurrent transmission of huge data through CSMA/CA incurs more packet collision rate. This complicated condition has to be eliminated to improve the system throughput. In this study, we propose to deploy cluster based TDMA scheduling mechanism for IEEE 802.15.4 ZigBee Wireless Sensor Networks. This TDMA slot allocation strategy allocates slots to the nodes...

  14. Spectrum-efficient multi-channel design for coexisting IEEE 802.15.4 networks: A stochastic geometry approach

    KAUST Repository

    Elsawy, Hesham

    2014-07-01

    For networks with random topologies (e.g., wireless ad-hoc and sensor networks) and dynamically varying channel gains, choosing the long term operating parameters that optimize the network performance metrics is very challenging. In this paper, we use stochastic geometry analysis to develop a novel framework to design spectrum-efficient multi-channel random wireless networks based on the IEEE 802.15.4 standard. The proposed framework maximizes both spatial and time domain frequency utilization under channel gain uncertainties to minimize the number of frequency channels required to accommodate a certain population of coexisting IEEE 802.15.4 networks. The performance metrics are the outage probability and the self admission failure probability. We relax the single channel assumption that has been used traditionally in the stochastic geometry analysis. We show that the intensity of the admitted networks does not increase linearly with the number of channels and the rate of increase of the intensity of the admitted networks decreases with the number of channels. By using graph theory, we obtain the minimum required number of channels to accommodate a certain intensity of coexisting networks under a self admission failure probability constraint. To this end, we design a superframe structure for the coexisting IEEE 802.15.4 networks and a method for time-domain interference alignment. © 2002-2012 IEEE.

  15. Cognitive wireless networks

    CERN Document Server

    Feng, Zhiyong; Zhang, Ping

    2015-01-01

    This brief examines the current research in cognitive wireless networks (CWNs). Along with a review of challenges in CWNs, this brief presents novel theoretical studies and architecture models for CWNs, advances in the cognitive information awareness and delivery, and intelligent resource management technologies. The brief presents the motivations and concepts of CWNs, including theoretical studies of temporal and geographic distribution entropy as well as cognitive information metrics. A new architecture model of CWNs is proposed with theoretical, functional and deployment architectures suppo

  16. Reactor building indoor wireless network channel quality estimation using RSSI measurement of wireless sensor network

    International Nuclear Information System (INIS)

    Merat, S.

    2008-01-01

    Expanding wireless communication network reception inside reactor buildings (RB) and service wings (SW) has always been a technical challenge for operations service team. This is driven by the volume of metal equipment inside the Reactor Buildings (RB) that blocks and somehow shields the signal throughout the link. In this study, to improve wireless reception inside the Reactor Building (RB), an experimental model using indoor localization mesh based on IEEE 802.15 is developed to implement a wireless sensor network. This experimental model estimates the distance between different nodes by measuring the RSSI (Received Signal Strength Indicator). Then by using triangulation and RSSI measurement, the validity of the estimation techniques is verified to simulate the physical environmental obstacles, which block the signal transmission. (author)

  17. Time Synchronized Wireless Sensor Network for Vibration Measurement

    Science.gov (United States)

    Uchimura, Yutaka; Nasu, Tadashi; Takahashi, Motoichi

    Network based wireless sensing has become an important area of research and various new applications for remote sensing are expected to emerge. One of the promising applications is structural health monitoring of building or civil engineering structure and it often requires vibration measurement. For the vibration measurement via wireless network, time synchronization is indispensable. In this paper, we introduce a newly developed time synchronized wireless sensor network system. The system employs IEEE 802.11 standard based TSF counter and sends the measured data with the counter value. TSF based synchronization enables consistency on common clock among different wireless nodes. We consider the scale effect on the synchronization accuracy and the effect is evaluated by stochastic analysis and simulation studies. A new wireless sensing system is developed and the hardware and software specifications are shown. The experiments are conducted in a reinforced concrete building and results show good performance enough for vibration measurement purpose.

  18. Double dipole antenna for dual-band wireless local area networks applications

    CSIR Research Space (South Africa)

    Steyn, JM

    2009-09-01

    Full Text Available A double dipole antenna design is proposed for wireless local area network (WLAN) applications. Two parallel dipoles are used to facilitate operation in both the standard WLAN frequency bands (IEEE 802.11b and IEEE 802.11a) simultaneously. The lower...

  19. Wireless Local Area Network Performance Inside Aircraft Passenger Cabins

    Science.gov (United States)

    Whetten, Frank L.; Soroker, Andrew; Whetten, Dennis A.; Whetten, Frank L.; Beggs, John H.

    2005-01-01

    An examination of IEEE 802.11 wireless network performance within an aircraft fuselage is performed. This examination measured the propagated RF power along the length of the fuselage, and the associated network performance: the link speed, total throughput, and packet losses and errors. A total of four airplanes: one single-aisle and three twin-aisle airplanes were tested with 802.11a, 802.11b, and 802.11g networks.

  20. Dynamic Contention Window Control Scheme in IEEE 802.11e EDCA-Based Wireless LANs

    Science.gov (United States)

    Abeysekera, B. A. Hirantha Sithira; Matsuda, Takahiro; Takine, Tetsuya

    In the IEEE 802.11 MAC protocol, access points (APs) are given the same priority as wireless terminals in terms of acquiring the wireless link, even though they aggregate several downlink flows. This feature leads to a serious throughput degradation of downlink flows, compared with uplink flows. In this paper, we propose a dynamic contention window control scheme for the IEEE 802.11e EDCA-based wireless LANs, in order to achieve fairness between uplink and downlink TCP flows while guaranteeing QoS requirements for real-time traffic. The proposed scheme first determines the minimum contention window size in the best-effort access category at APs, based on the number of TCP flows. It then determines the minimum and maximum contention window sizes in higher priority access categories, such as voice and video, so as to guarantee QoS requirements for these real-time traffic. Note that the proposed scheme does not require any modification to the MAC protocol at wireless terminals. Through simulation experiments, we show the effectiveness of the proposed scheme.

  1. ZigBee wireless sensor network for environmental monitoring system

    Science.gov (United States)

    Chai, Shun-qi; Ji, Lei; Wu, Hong

    2009-11-01

    ZigBee is a new close-up, low-complexity, low-power, low data rate, low-cost wireless networking technology, mainly used for short distance wireless transmission. It is based on IEEE802.15.4 standards, thousands of tiny sensors form a network through mutual coordination to communications. This paper introduces the ZigBee wireless sensor networks in environmental monitoring applications. The hardware design, including microprocessor, data acquisition, antenna and peripheral circuits of the chips, and through software design composed ZigBee mesh network that can make data acquisition and communication. This network has low power consumption, low cost, the effective area is big, and information transfers reliable merits. And have confirmed the network's communication applicability by the Serial Com Assistant, also testified the network have very good pragmatism by the NS2 emulation the network's operation.

  2. Applying Physical-Layer Network Coding in Wireless Networks

    Directory of Open Access Journals (Sweden)

    Soung Chang Liew

    2010-01-01

    Full Text Available A main distinguishing feature of a wireless network compared with a wired network is its broadcast nature, in which the signal transmitted by a node may reach several other nodes, and a node may receive signals from several other nodes, simultaneously. Rather than a blessing, this feature is treated more as an interference-inducing nuisance in most wireless networks today (e.g., IEEE 802.11. This paper shows that the concept of network coding can be applied at the physical layer to turn the broadcast property into a capacity-boosting advantage in wireless ad hoc networks. Specifically, we propose a physical-layer network coding (PNC scheme to coordinate transmissions among nodes. In contrast to “straightforward” network coding which performs coding arithmetic on digital bit streams after they have been received, PNC makes use of the additive nature of simultaneously arriving electromagnetic (EM waves for equivalent coding operation. And in doing so, PNC can potentially achieve 100% and 50% throughput increases compared with traditional transmission and straightforward network coding, respectively, in 1D regular linear networks with multiple random flows. The throughput improvements are even larger in 2D regular networks: 200% and 100%, respectively.

  3. Applying Physical-Layer Network Coding in Wireless Networks

    Directory of Open Access Journals (Sweden)

    Liew SoungChang

    2010-01-01

    Full Text Available A main distinguishing feature of a wireless network compared with a wired network is its broadcast nature, in which the signal transmitted by a node may reach several other nodes, and a node may receive signals from several other nodes, simultaneously. Rather than a blessing, this feature is treated more as an interference-inducing nuisance in most wireless networks today (e.g., IEEE 802.11. This paper shows that the concept of network coding can be applied at the physical layer to turn the broadcast property into a capacity-boosting advantage in wireless ad hoc networks. Specifically, we propose a physical-layer network coding (PNC scheme to coordinate transmissions among nodes. In contrast to "straightforward" network coding which performs coding arithmetic on digital bit streams after they have been received, PNC makes use of the additive nature of simultaneously arriving electromagnetic (EM waves for equivalent coding operation. And in doing so, PNC can potentially achieve 100% and 50% throughput increases compared with traditional transmission and straightforward network coding, respectively, in 1D regular linear networks with multiple random flows. The throughput improvements are even larger in 2D regular networks: 200% and 100%, respectively.

  4. Analysis of Adaptive Control Scheme in IEEE 802.11 and IEEE 802.11e Wireless LANs

    Science.gov (United States)

    Lee, Bih-Hwang; Lai, Hui-Cheng

    In order to achieve the prioritized quality of service (QoS) guarantee, the IEEE 802.11e EDCAF (the enhanced distributed channel access function) provides the distinguished services by configuring the different QoS parameters to different access categories (ACs). An admission control scheme is needed to maximize the utilization of wireless channel. Most of papers study throughput improvement by solving the complicated multidimensional Markov-chain model. In this paper, we introduce a back-off model to study the transmission probability of the different arbitration interframe space number (AIFSN) and the minimum contention window size (CWmin). We propose an adaptive control scheme (ACS) to dynamically update AIFSN and CWmin based on the periodical monitoring of current channel status and QoS requirements to achieve the specific service differentiation at access points (AP). This paper provides an effective tuning mechanism for improving QoS in WLAN. Analytical and simulation results show that the proposed scheme outperforms the basic EDCAF in terms of throughput and service differentiation especially at high collision rate.

  5. Handoff Between a Wireless Local Area Network (WLAN and a Wide Area Network (UMTS

    Directory of Open Access Journals (Sweden)

    J. Sánchez–García

    2009-04-01

    Full Text Available With the appearance of wireless data networks with variable coverage, band width and handoff strategies, in addition to the growing need of mobile nodes to freely roam among these networks, the support of an interoperable handoff strategy for hybrid wireless data networks is a requirement that needs to be addressed. The current trend in wireless data networks is to offer multimedia access to mobile users by employing the wireless local area network (WLAN standard IEEE802.11 while the user is located indoors; on the other hand, 3rd generation wireless networks (WAN are being deployed to provide coverage while the user is located outdoors. As a result, the mobile node will require a handoff mechanism to allow the user to roam between WLAN and WAN environments; up to this date several strategies have been proposed (Sattari et al., 2004 and HyoJin, 2007 in the literature, however, none of these have been standardized to date. To support this interoperability, the mobile node must be equipped with configurable wireless inetrfaces to support the handoff between the WLAN and the WAN networks. In this work a new algorithm is proposed to allow a mobile node to roam between a wireless local area network (IEEE802.11 and a WAN base station (UMTS, while employing IP mobility support. The algorithm is implemented in simulation, using the Network Simulator 2.

  6. A MAC Technique for VoIP Services Using Back off Algorithm in IEEE 802.11e Networks

    OpenAIRE

    K. Sumalatha; Dr. Ramakrishna Rao T. K

    2012-01-01

    In the advent of emerging information super highway, voice over Internet Protocol has become a vital service with the demand for high quality of requirements in Wireless Local Area Network(WLANs). The IEEE 802.11e Standard has been recently introduced to mark the Quality of Service (QoS) competence in the ever evolving wireless local area networks. This 802.11e brings contention window, based on Enhanced Distribution Channel Access technique that offers a selected traffic to ensure least band...

  7. Comparison of Analytical and Measured Performance Results on Network Coding in IEEE 802.11 Ad-Hoc Networks

    DEFF Research Database (Denmark)

    Zhao, Fang; Médard, Muriel; Hundebøll, Martin

    2012-01-01

    CATWOMAN that can run on standard WiFi hardware. We present an analytical model to evaluate the performance of COPE in simple networks, and our results show the excellent predictive quality of this model. By closely examining the performance in two simple topologies, we observe that the coding gain results......Network coding is a promising technology that has been shown to improve throughput in wireless mesh networks. In this paper, we compare the analytical and experimental performance of COPE-style network coding in IEEE 802.11 ad-hoc networks. In the experiments, we use a lightweight scheme called...... from the interaction between network coding and the MAC protocol, and the gap between the theoretical and practical gains is due to the different channel qualities of sending nodes. This understanding is helpful for design of larger mesh networks that use network coding....

  8. Implementing 802.11 with microcontrollers wireless networking for embedded systems designers

    CERN Document Server

    Eady, Fred

    2005-01-01

    Wireless networking is poised to have a massive impact on communications, and the 802.11 standard is to wireless networking what Ethernet is to wired networking. There are already over 50 million devices using the dominant IEEE 802.11 (essentially wireless Ethernet) standard, with astronomical growth predicted over the next 10 years. New applications are emerging every day, with wireless capability being embedded in everything from electric meters to hospital patient tracking systems to security devices. This practical reference guides readers through the wireless technology forest, gi

  9. Performance comparison of IEEE 802.11g and IEEE 802.11n in the presence of interference from 802.15.4 networks

    OpenAIRE

    Masood, Syed Haani

    2013-01-01

    In this paper we compare the packet error rate (PER) and maximum throughput of IEEE 802.11n and IEEE 802.11g under interference from IEEE 802.15.4 by using MATLAB to simulate the IEEE PHY for 802.11n and 802.11g networks.

  10. EAP-Kerberos: A Low Latency EAP Authentication Method for Faster Handoffs in Wireless Access Networks

    Science.gov (United States)

    Zrelli, Saber; Okabe, Nobuo; Shinoda, Yoichi

    The wireless medium is a key technology for enabling ubiquitous and continuous network connectivity. It is becoming more and more important in our daily life especially with the increasing adoption of networking technologies in many fields such as medical care and transportation systems. Although most wireless technologies nowadays provide satisfying bandwidth and higher speeds, several of these technologies still lack improvements with regard to handoff performance. In this paper, we focus on wireless network technologies that rely on the Extensible Authentication Protocol for mutual authentication between the station and the access network. Such technologies include local area wireless networks (IEEE 802.11) as well as broadband wireless networks (IEEE 802.16). We present a new EAP authentication method based on a three party authentication scheme, namely Kerberos, that considerably shortens handoff delays. Compared to other methods, the proposed method has the advantage of not requiring any changes on the access points, making it readily deployable at reasonable costs.

  11. Experimental video signals distribution MMF network based on IEEE 802.11 standard

    Science.gov (United States)

    Kowalczyk, Marcin; Maksymiuk, Lukasz; Siuzdak, Jerzy

    2014-11-01

    The article was focused on presentation the achievements in a scope of experimental research on transmission of digital video streams in the frame of specially realized for this purpose ROF (Radio over Fiber) network. Its construction was based on the merge of wireless IEEE 802.11 network, popularly referred as Wi-Fi, with a passive optical network PON based on multimode fibers MMF. The proposed approach can constitute interesting proposal in area of solutions in the scope of the systems monitoring extensive, within which is required covering of a large area with ensuring of a relatively high degree of immunity on the interferences transmitted signals from video IP cameras to the monitoring center and a high configuration flexibility (easily change the deployment of cameras) of such network.

  12. Connectivity-Based Reliable Multicast MAC Protocol for IEEE 802.11 Wireless LANs

    Directory of Open Access Journals (Sweden)

    Woo-Yong Choi

    2009-01-01

    Full Text Available We propose the efficient reliable multicast MAC protocol based on the connectivity information among the recipients. Enhancing the BMMM (Batch Mode Multicast MAC protocol, the reliable multicast MAC protocol significantly reduces the RAK (Request for ACK frame transmissions in a reasonable computational time and enhances the MAC performance. By the analytical performance analysis, the throughputs of the BMMM protocol and our proposed MAC protocol are derived. Numerical examples show that our proposed MAC protocol increases the reliable multicast MAC performance for IEEE 802.11 wireless LANs.

  13. Performance of the hybrid wireless mesh protocol for wireless mesh networks

    DEFF Research Database (Denmark)

    Boye, Magnus; Staalhagen, Lars

    2010-01-01

    . These challenges must first be overcome before satisfactory network stability and throughput can be achieved. This paper studies the performance of the Hybrid Wireless Mesh Protocol, the proposed routing protocol for the upcoming IEEE 802.11s standard. HWMP supports two modes of path selection: reactive...... and proactive. Two scenarios of different node density are considered for both path selection modes. The results presented in this paper are based on a simulation model of the HWMP specification in the IEEE 802.11s draft 4.0 implemented in OPNET Modeler....

  14. ReSF : recurrent low-latency scheduling in IEEE 802.15.4e TSCH networks

    OpenAIRE

    Daneels, Glenn; Spinnewyn, Bart; Latré, Steven; Famaey, Jeroen

    2018-01-01

    Abstract: The recent increase of connected devices has triggered countless Internet-of-Things applications to emerge. By using the Time-Slotted Channel Hopping (TSCH) mode of the IEEE 802.15.4e MAC layer, wireless multi-hop networks enable highly reliable and low-power communication, supporting mission-critical and industrial applications. TSCH uses channel hopping to avoid both external interference and multi-path fading, and a synchronization-based schedule which allows precise bandwidth al...

  15. Wireless home networking for dummies

    CERN Document Server

    Briere, Danny; Ferris, Edward

    2010-01-01

    The perennial bestseller shows you how share your files and Internet connection across a wireless network. Fully updated for Windows 7 and Mac OS X Snow Leopard, this new edition of this bestseller returns with all the latest in wireless standards and security. This fun and friendly guide shows you how to integrate your iPhone, iPod touch, smartphone, or gaming system into your home network. Veteran authors escort you through the various financial and logisitical considerations that you need to take into account before building a wireless network at home.: Covers the basics of planning, instal

  16. Wireless Ad Hoc Networks

    Directory of Open Access Journals (Sweden)

    Hong-Chuan Yang

    2007-01-01

    Full Text Available We study the energy-efficient configuration of multihop paths with automatic repeat request (ARQ mechanism in wireless ad hoc networks. We adopt a cross-layer design approach and take both the quality of each radio hop and the battery capacity of each transmitting node into consideration. Under certain constraints on the maximum tolerable transmission delay and the required packet delivery ratio, we solve optimization problems to jointly schedule the transmitting power of each transmitting node and the retransmission limit over each hop. Numerical results demonstrate that the path configuration methods can either significantly reduce the average energy consumption per packet delivery or considerably extend the average lifetime of the multihop route.

  17. IEEE 802154 and ZigBee as enabling technologies for low-power wireless systems with quality-of-service constraints

    CERN Document Server

    Tennina, Stefano; Daidone, Roberta; Alves, Mário; Jurčík, Petr; Severino, Ricardo; Tiloca, Marco; Hauer, Jan-Hinrich; Pereira, Nuno; Dini, Gianluca; Bouroche, Mélanie; Tovar, Eduardo

    2013-01-01

    This book outlines the most important characteristics of IEEE 802.15.4 and ZigBee and how they can be used to engineer Wireless Sensor Network (WSN) systems and applications, with a particular focus on Quality-of-Service (QoS) aspects. It starts by providing a snapshot of the most relevant features of these two protocols, identifying some gaps in the standard specifications. Then it describes several state-of-the-art open-source implementations, models and tools that have been designed by the authors and have been widely used by the international community. The book also outlines the fundamental performance limits of IEEE 802.15.4/ZigBee networks, based on well-sustained analytical, simulation and experimental models, including how to dimension such networks to optimize delay/energy trade-offs.

  18. Green Wireless Power Transfer Networks

    NARCIS (Netherlands)

    Liu, Q.; Golinnski, M.; Pawelczak, P.; Warnier, M.

    2016-01-01

    wireless power transfer network (WPTN) aims to support devices with cable-less energy on-demand. Unfortunately, wireless power transfer itself-especially through radio frequency radiation rectification-is fairly inefficient due to decaying power with distance, antenna polarization, etc.

  19. Wireless Networks: a brief introduction

    Indian Academy of Sciences (India)

    First page Back Continue Last page Overview Graphics. Wireless Networks: a brief introduction. Wireless communication: What? Why? How many types? What is cell? Is it different from fixed landline structure? 1G systems: FDMA/FDD and Analog FM [voice comm]. (Introduced in 1983 in Chicago by AMPS). 2G systems: 3 ...

  20. The Performance Evaluation of an IEEE 802.11 Network Containing Misbehavior Nodes under Different Backoff Algorithms

    Directory of Open Access Journals (Sweden)

    Trong-Minh Hoang

    2017-01-01

    Full Text Available Security of any wireless network is always an important issue due to its serious impacts on network performance. Practically, the IEEE 802.11 medium access control can be violated by several native or smart attacks that result in downgrading network performance. In recent years, there are several studies using analytical model to analyze medium access control (MAC layer misbehavior issue to explore this problem but they have focused on binary exponential backoff only. Moreover, a practical condition such as the freezing backoff issue is not included in the previous models. Hence, this paper presents a novel analytical model of the IEEE 802.11 MAC to thoroughly understand impacts of misbehaving node on network throughput and delay parameters. Particularly, the model can express detailed backoff algorithms so that the evaluation of the network performance under some typical attacks through numerical simulation results would be easy.

  1. Industrial wireless networking with resource constraint devices

    NARCIS (Netherlands)

    Das, Kallol

    2015-01-01

    During the last decade, wireless technologies have revolutionized the industrial automation sector by enabling wireless sensing and actuation for industrial applications. Most of these recently developed industrial standards are built on top of IEEE802.15.4 interface, which uses 2.4GHz frequency

  2. Wireless network security theories and applications

    CERN Document Server

    Chen, Lei; Zhang, Zihong

    2013-01-01

    Wireless Network Security Theories and Applications discusses the relevant security technologies, vulnerabilities, and potential threats, and introduces the corresponding security standards and protocols, as well as provides solutions to security concerns. Authors of each chapter in this book, mostly top researchers in relevant research fields in the U.S. and China, presented their research findings and results about the security of the following types of wireless networks: Wireless Cellular Networks, Wireless Local Area Networks (WLANs), Wireless Metropolitan Area Networks (WMANs), Bluetooth

  3. Adaptive management of energy consumption, reliability and delay of wireless sensor node: Application to IEEE 802.15.4 wireless sensor node.

    Science.gov (United States)

    Kone, Cheick Tidjane; Mathias, Jean-Denis; De Sousa, Gil

    2017-01-01

    Designing a Wireless Sensor Network (WSN) to achieve a high Quality of Service (QoS) (network performance and durability) is a challenging problem. We address it by focusing on the performance of the 802.15.4 communication protocol because the IEEE 802.15.4 Standard is actually considered as one of the reference technologies in WSNs. In this paper, we propose to control the sustainable use of resources (i.e., energy consumption, reliability and timely packet transmission) of a wireless sensor node equipped with photovoltaic cells by an adaptive tuning not only of the MAC (Medium Access Control) parameters but also of the sampling frequency of the node. To do this, we use one of the existing control approaches, namely the viability theory, which aims to preserve the functions and the controls of a dynamic system in a set of desirable states. So, an analytical model, describing the evolution over time of nodal resources, is derived and used by a viability algorithm for the adaptive tuning of the IEEE 802.15.4 MAC protocol. The simulation analysis shows that our solution allows ensuring indefinitely, in the absence of hardware failure, the operations (lifetime duration, reliability and timely packet transmission) of an 802.15.4 WSN and one can temporarily increase the sampling frequency of the node beyond the regular sampling one. This latter brings advantages for agricultural and environmental applications such as precision agriculture, flood or fire prevention. Main results show that our current approach enable to send more information when critical events occur without the node runs out of energy. Finally, we argue that our approach is generic and can be applied to other types of WSN.

  4. Secure positioning in wireless networks

    DEFF Research Database (Denmark)

    Capkun, Srdjan; Hubaux, Jean-Pierre

    2006-01-01

    So far, the problem of positioning in wireless networks has been studied mainly in a non-adversarial settings. In this work, we analyze the resistance of positioning techniques to position and distance spoofing attacks. We propose a mechanism for secure positioning of wireless devices, that we call...... Verifiable Multilateration. We then show how this mechanism can be used to secure positioning in sensor networks. We analyze our system through simulations....

  5. Introduction to wireless sensor networks

    CERN Document Server

    Forster, Anna

    2016-01-01

    Explores real-world wireless sensor network development, deployment, and applications. The book begins with an introduction to wireless sensor networks and their fundamental concepts. Hardware components, operating systems, protocols, and algorithms that make up the anatomy of a sensor node are described in chapter two. Properties of wireless communications, medium access protocols, wireless links, and link estimation protocols are described in chapter three and chapter four. Routing basics and metrics, clustering techniques, time synchronization and localization protocols, as well as sensing techniques are introduced in chapter five to nine. The concluding chapter summarizes the learnt methods and shows how to use them to deploy real-world sensor networks in a structured way.

  6. Hybrid Polling Method for Direct Link Communication for IEEE 802.11 Wireless LANs

    Directory of Open Access Journals (Sweden)

    Woo-Yong Choi

    2008-10-01

    Full Text Available The direct link communication between STAtions (STAs is one of the techniques to improve the MAC performance of IEEE 802.11 infrastructure networks. For the efficient direct link communication, in the literature, the simultaneous polling method was proposed to allow the multiple direct data communication to be performed simultaneously. However, the efficiency of the simultaneous polling method is affected by the interference condition. To alleviate the problem of the lower polling efficiency with the larger interference range, the hybrid polling method is proposed for the direct link communication between STAs in IEEE 802.11 infrastructure networks. By the proposed polling method, we can integrate the sequential and simultaneous polling methods properly according to the interference condition. Numerical examples are also presented to show the medium access control (MAC performance improvement by the proposed polling method.

  7. Intrusion detection for IP-based multimedia communications over wireless networks

    CERN Document Server

    Tang, Jin

    2013-01-01

    IP-based multimedia communications have become increasingly popular in recent years. With the increasing coverage of the IEEE 802:11™ based wireless networks, IP-based multimedia communications over wireless networks are also drawing extensive attention in both academia and industry. Due to the openness and distributed nature of the protocols involved, such as the session initiation protocol (SIP) and the IEEE 802:11™ standard, it becomes easy for malicious users in the network to achieve their own gain or disrupt the service by deviating from the normal protocol behaviors. This SpringerBrief

  8. Fair packet scheduling in Wireless Mesh Networks

    KAUST Repository

    Nawab, Faisal

    2014-02-01

    In this paper we study the interactions of TCP and IEEE 802.11 MAC in Wireless Mesh Networks (WMNs). We use a Markov chain to capture the behavior of TCP sessions, particularly the impact on network throughput due to the effect of queue utilization and packet relaying. A closed form solution is derived to numerically determine the throughput. Based on the developed model, we propose a distributed MAC protocol called Timestamp-ordered MAC (TMAC), aiming to alleviate the unfairness problem in WMNs. TMAC extends CSMA/CA by scheduling data packets based on their age. Prior to transmitting a data packet, a transmitter broadcasts a request control message appended with a timestamp to a selected list of neighbors. It can proceed with the transmission only if it receives a sufficient number of grant control messages from these neighbors. A grant message indicates that the associated data packet has the lowest timestamp of all the packets pending transmission at the local transmit queue. We demonstrate that a loose ordering of timestamps among neighboring nodes is sufficient for enforcing local fairness, subsequently leading to flow rate fairness in a multi-hop WMN. We show that TMAC can be implemented using the control frames in IEEE 802.11, and thus can be easily integrated in existing 802.11-based WMNs. Our simulation results show that TMAC achieves excellent resource allocation fairness while maintaining over 90% of maximum link capacity across a large number of topologies.

  9. Backoff-stage synchronization in three-hop string-topology wireless networks with hidden nodes

    Science.gov (United States)

    Sanada, Kosuke; Sekiya, Hiroo; Komuro, Nobuyoshi; Sakata, Shiro

    In IEEE 802.11 wireless multi-hop networks, each node works individually and their individual operations generate entire network dynamics. It is important to clarify the network dynamics in wireless multi-hop networks for designing and constructing multi-hop communication networks. This paper presents the network-dynamics investigations for three-hop string-topology wireless network in detail. From the investigations, a “backoff-stage synchronization” phenomenon, which is mutuality between hidden nodes, is found. The mechanism of the backoff-stage synchronization is expressed and the sufficient conditions for the synchronization occurrence are given. This phenomenon gives some impacts on the IEEE 802.11 multi-hop-network communications.

  10. Reliable Multicast MAC Protocol for IEEE 802.11 Wireless LANs with Extended Service Range

    Science.gov (United States)

    Choi, Woo-Yong

    2011-11-01

    In this paper, we propose the efficient reliable multicast MAC protocol by which the AP (Access Point) can transmit reliably its multicast data frames to the recipients in the AP's one-hop or two-hop transmission range. The AP uses the STAs (Stations) that are directly associated with itself as the relays for the data delivery to the remote recipients that cannot be reached directly from itself. Based on the connectivity information among the recipients, the reliable multicast MAC protocol optimizes the number of the RAK (Request for ACK) frame transmissions in a reasonable computational time. Numerical examples show that our proposed MAC protocol significantly enhances the MAC performance compared with the BMMM (Batch Mode Multicast MAC) protocol that is extended to support the recipients that are in the AP's one-hop or two-hop transmission range in IEEE 802.11 wireless LANs.

  11. Emerging wireless networks concepts, techniques and applications

    CERN Document Server

    Makaya, Christian

    2011-01-01

    An authoritative collection of research papers and surveys, Emerging Wireless Networks: Concepts, Techniques, and Applications explores recent developments in next-generation wireless networks (NGWNs) and mobile broadband networks technologies, including 4G (LTE, WiMAX), 3G (UMTS, HSPA), WiFi, mobile ad hoc networks, mesh networks, and wireless sensor networks. Focusing on improving the performance of wireless networks and provisioning better quality of service and quality of experience for users, it reports on the standards of different emerging wireless networks, applications, and service fr

  12. Design and initial deployment of the wireless local area networking infrastructure at Sandia National Laboratories.

    Energy Technology Data Exchange (ETDEWEB)

    Long, John P.; Hamill, Michael J.; Mitchell, M. G.; Miller, Marc M.; Witzke, Edward L.; Wiener, Dallas J

    2006-11-01

    A major portion of the Wireless Networking Project at Sandia National Laboratories over the last few years has been to examine IEEE 802.11 wireless networking for possible use at Sandia and if practical, introduce this technology. This project team deployed 802.11a, b, and g Wireless Local Area Networking at Sandia. This report examines the basics of wireless networking and captures key results from project tests and experiments. It also records project members thoughts and designs on wireless LAN architecture and security issues. It documents some of the actions and milestones of this project, including pilot and production deployment of wireless networking equipment, and captures the team's rationale behind some of the decisions made. Finally, the report examines lessons learned, future directions, and conclusions.

  13. Traffic Profiling in Wireless Sensor Networks

    National Research Council Canada - National Science Library

    Kirykos, Georgios

    2006-01-01

    .... Wireless sensor networks pose unique challenges and limitations to the traditional schemes, which are used in the other wireless networks for security protection, and are due mainly to the increased...

  14. Socially Aware Heterogeneous Wireless Networks.

    Science.gov (United States)

    Kosmides, Pavlos; Adamopoulou, Evgenia; Demestichas, Konstantinos; Theologou, Michael; Anagnostou, Miltiades; Rouskas, Angelos

    2015-06-11

    The development of smart cities has been the epicentre of many researchers' efforts during the past decade. One of the key requirements for smart city networks is mobility and this is the reason stable, reliable and high-quality wireless communications are needed in order to connect people and devices. Most research efforts so far, have used different kinds of wireless and sensor networks, making interoperability rather difficult to accomplish in smart cities. One common solution proposed in the recent literature is the use of software defined networks (SDNs), in order to enhance interoperability among the various heterogeneous wireless networks. In addition, SDNs can take advantage of the data retrieved from available sensors and use them as part of the intelligent decision making process contacted during the resource allocation procedure. In this paper, we propose an architecture combining heterogeneous wireless networks with social networks using SDNs. Specifically, we exploit the information retrieved from location based social networks regarding users' locations and we attempt to predict areas that will be crowded by using specially-designed machine learning techniques. By recognizing possible crowded areas, we can provide mobile operators with recommendations about areas requiring datacell activation or deactivation.

  15. 802.11s Wireless Mesh Network Visualization Application

    Science.gov (United States)

    Mauldin, James Alexander

    2014-01-01

    Results of past experimentation at NASA Johnson Space Center showed that the IEEE 802.11s standard has better performance than the widely implemented alternative protocol B.A.T.M.A.N (Better Approach to Mobile Ad hoc Networking). 802.11s is now formally incorporated into the Wi- Fi 802.11-2012 standard, which specifies a hybrid wireless mesh networking protocol (HWMP). In order to quickly analyze changes to the routing algorithm and to support optimizing the mesh network behavior for our intended application a visualization tool was developed by modifying and integrating open source tools.

  16. Security Threats on Wireless Sensor Network Protocols

    OpenAIRE

    H. Gorine; M. Ramadan Elmezughi

    2016-01-01

    In this paper, we investigate security issues and challenges facing researchers in wireless sensor networks and countermeasures to resolve them. The broadcast nature of wireless communication makes Wireless Sensor Networks prone to various attacks. Due to resources limitation constraint in terms of limited energy, computation power and memory, security in wireless sensor networks creates different challenges than wired network security. We will discuss several attempts at addressing the issue...

  17. Design and security of small wireless network

    OpenAIRE

    Žižka, Ladislav

    2012-01-01

    This thesis deals with design and security of small wireless network. Main goal of the thesis is home network design and choice of optimal solution of wireless security. The thesis has four parts. The first part describes computer networks and network components in theory. Next part deals with network design, choosing of network components and setting of them. It also describes some functionalities of alternative firmware DD-WRT. The third part presents common wireless security and network an...

  18. Experience of wireless local area network in a radiation oncology department

    Directory of Open Access Journals (Sweden)

    Mandal Abhijit

    2010-01-01

    Full Text Available The aim of this work is to develop a wireless local area network (LAN between different types of users (Radiation Oncologists, Radiological Physicists, Radiation Technologists, etc for efficient patient data management and to made easy the availability of information (chair side to improve the quality of patient care in Radiation Oncology department. We have used mobile workstations (Laptops and stationary workstations, all equipped with wireless-fidelity (Wi-Fi access. Wireless standard 802.11g (as recommended by Institute of Electrical and Electronic Engineers (IEEE, Piscataway, NJ has been used. The wireless networking was configured with the Service Set Identifier (SSID, Media Access Control (MAC address filtering, and Wired Equivalent Privacy (WEP network securities. We are successfully using this wireless network in sharing the indigenously developed patient information management software. The proper selection of the hardware and the software combined with a secure wireless LAN setup will lead to a more efficient and productive radiation oncology department.

  19. A New Mechanism for Network Monitoring and Shielding in Wireless LAN

    Directory of Open Access Journals (Sweden)

    Jiujun Cheng

    2014-01-01

    Full Text Available Wireless LAN (WLAN technology is developing rapidly with the help of wireless communication technology and social demand. During the development of WLAN, the security is more and more important, and wireless monitoring and shielding are of prime importance for network security. In this paper, we have explored various security issues of IEEE 802.11 based wireless network and analyzed numerous problems in implementing the wireless monitoring and shielding system. We identify the challenges which monitoring and shielding system needs to be aware of, and then provide a feasible mechanism to avoid those challenges. We implemented an actual wireless LAN monitoring and shielding system on Maemo operating system to monitor wireless network data stream efficiently and solve the security problems of mobile users. More importantly, the system analyzes wireless network protocols efficiently and flexibly, reveals rich information of the IEEE 802.11 protocol such as traffic distribution and different IP connections, and graphically displays later. Moreover, the system running results show that the system has the capability to work stably, and accurately and analyze the wireless protocols efficiently.

  20. SIMULATION OF WIRELESS SENSOR NETWORK WITH HYBRID TOPOLOGY

    Directory of Open Access Journals (Sweden)

    J. Jaslin Deva Gifty

    2016-03-01

    Full Text Available The design of low rate Wireless Personal Area Network (WPAN by IEEE 802.15.4 standard has been developed to support lower data rates and low power consuming application. Zigbee Wireless Sensor Network (WSN works on the network and application layer in IEEE 802.15.4. Zigbee network can be configured in star, tree or mesh topology. The performance varies from topology to topology. The performance parameters such as network lifetime, energy consumption, throughput, delay in data delivery and sensor field coverage area varies depending on the network topology. In this paper, designing of hybrid topology by using two possible combinations such as star-tree and star-mesh is simulated to verify the communication reliability. This approach is to combine all the benefits of two network model. The parameters such as jitter, delay and throughput are measured for these scenarios. Further, MAC parameters impact such as beacon order (BO and super frame order (SO for low power consumption and high channel utilization, has been analysed for star, tree and mesh topology in beacon disable mode and beacon enable mode by varying CBR traffic loads.

  1. Scheduling High-Rate Unpredictable Traffic in IEEE 802.15.4 TSCH Networks

    OpenAIRE

    Elsts, Atis; Fafoutis, Xenofon; Pope, James; Oikonomou, George; Piechocki, Robert; Craddock, Ian

    2018-01-01

    The upcoming Internet of Things (IoT) applications include real-time human activity monitoring with wearable sensors. Compared to the traditional environmental sensing with low-power wireless nodes, these new applicationsgenerate a constant stream of a much higher rate. Nevertheless, the wearable devices remain battery powered and therefore restricted to low-power wireless standards such as IEEE 802.15.4 or Bluetooth Low Energy (BLE). Our work tacklesthe problem of building a reliable autonom...

  2. Mathematical Analysis of EDCA's Performance on the Control Channel of an IEEE 802.11p WAVE Vehicular Network

    Directory of Open Access Journals (Sweden)

    Hussein T. Mouftah

    2010-01-01

    Full Text Available Wireless networks for vehicular environments are gaining increasing importance due to their ability to provide a means for stations on the roadside and radio units on board of vehicles to communicate and share safety-related information, thus reducing the probability of accidents and increasing the efficiency of the transportation system. With this goal in mind, the IEEE is currently developing the Wireless Access in Vehicular Environments (WAVE IEEE 802.11p standard. WAVE devices use the IEEE 802.11's Enhanced Distributed Channel Access (EDCA MAC protocol to compete for the transmission medium. This work proposes an analytical tool to evaluate the performance of EDCA under the specific conditions of the so-called control channel (CCH of a WAVE environment, including the particular EDCA parameter values and the fact that all safety-critical data frames are broadcasted. The protocol is modeled using Markov chains and results related to throughput, frame-error rate, buffer occupancy and delay are obtained under different traffic-load conditions. The main analysis is performed assuming that the CCH works continuously, and then an explanation is given as to the considerations that are needed to account for the fact that activity on the CCH is intermittent.

  3. WIRELESS FIDELITY (Wi-Fi) BROADBAND NETWORK ...

    African Journals Online (AJOL)

    ES Obe

    categorized into two types: fixed and mobile wireless. The broadband fixed wireless network technologies .... 3.0 WIRELESS FIDELITYF (Wi-Fi). NETWORK IMPLEMENTATION. A Wi-Fi enabled device such as a PC, game .... Amateur radio, video senders, and cordless phones, can cause significant additional interference.

  4. Underwater optical wireless communication network

    Science.gov (United States)

    Arnon, Shlomi

    2010-01-01

    The growing need for underwater observation and subsea monitoring systems has stimulated considerable interest in advancing the enabling technologies of underwater wireless communication and underwater sensor networks. This communication technology is expected to play an important role in investigating climate change, in monitoring biological, biogeochemical, evolutionary, and ecological changes in the sea, ocean, and lake environments, and in helping to control and maintain oil production facilities and harbors using unmanned underwater vehicles (UUVs), submarines, ships, buoys, and divers. However, the present technology of underwater acoustic communication cannot provide the high data rate required to investigate and monitor these environments and facilities. Optical wireless communication has been proposed as the best alternative to meet this challenge. Models are presented for three kinds of optical wireless communication links: (a) a line-of-sight link, (b) a modulating retroreflector link, and (c) a reflective link, all of which can provide the required data rate. We analyze the link performance based on these models. From the analysis, it is clear that as the water absorption increases, the communication performance decreases dramatically for the three link types. However, by using the scattered light it was possible to mitigate this decrease in some cases. It is concluded from the analysis that a high-data-rate underwater optical wireless network is a feasible solution for emerging applications such as UUV-to-UUV links and networks of sensors, and extended ranges in these applications could be achieved by applying a multi-hop concept.

  5. Fault Tolerance in ZigBee Wireless Sensor Networks

    Science.gov (United States)

    Alena, Richard; Gilstrap, Ray; Baldwin, Jarren; Stone, Thom; Wilson, Pete

    2011-01-01

    Wireless sensor networks (WSN) based on the IEEE 802.15.4 Personal Area Network standard are finding increasing use in the home automation and emerging smart energy markets. The network and application layers, based on the ZigBee 2007 PRO Standard, provide a convenient framework for component-based software that supports customer solutions from multiple vendors. This technology is supported by System-on-a-Chip solutions, resulting in extremely small and low-power nodes. The Wireless Connections in Space Project addresses the aerospace flight domain for both flight-critical and non-critical avionics. WSNs provide the inherent fault tolerance required for aerospace applications utilizing such technology. The team from Ames Research Center has developed techniques for assessing the fault tolerance of ZigBee WSNs challenged by radio frequency (RF) interference or WSN node failure.

  6. Dynamic wireless sensor networks

    CERN Document Server

    Oteafy, Sharief M A

    2014-01-01

    In this title, the authors leap into a novel paradigm of scalability and cost-effectiveness, on the basis of resource reuse. In a world with much abundance of wirelessly accessible devices, WSN deployments should capitalize on the resources already available in the region of deployment, and only augment it with the components required to meet new application requirements. However, if the required resources already exist in that region, WSN deployment converges to an assignment and scheduling scheme to accommodate for the new application given the existing resources. Such resources are polled

  7. Dynamic subframe allocation for mobile broadband m-health using IEEE 802.16j mobile multihop relay networks.

    Science.gov (United States)

    Alinejad, Ali; Istepanian, R S H; Philip, N

    2012-01-01

    The concept of 4G health will be one of the key focus areas of future m-health research and enterprise activities in the coming years. WiMAX technology is one of the constituent 4G wireless technologies that provides broadband wireless access (BWA). Despite the fact that WiMAX is able to provide a high data rate in a relatively large coverage; this technology has specific limitations such as: coverage, signal attenuation problems due to shadowing or path loss, and limited available spectrum. The IEEE 802.16j mobile multihop relay (MMR) technology is a pragmatic solution designed to overcome these limitations. The aim of IEEE 802.16j MMR is to expand the IEEE 802.16e's capabilities with multihop features. In particular, the uplink (UL) and downlink (DL) subframe allocation in WiMAX network is usually fixed. However, dynamic frame allocation is a useful mechanism to optimize uplink and downlink subframe size dynamically based on the traffic conditions through real-time traffic monitoring. This particular mechanism is important for future WiMAX based m-health applications as it allows the tradeoff in both UL and DL channels. In this paper, we address the dynamic frame allocation issue in IEEE 802.16j MMR network for m-health applications. A comparative performance analysis of the proposed approach is validated using the OPNET Modeler(®). The simulation results have shown an improved performance of resource allocation and end-to-end delay performance for typical medical video streaming application.

  8. Evaluation of video transmission of MAC protocols in wireless sensor network

    Science.gov (United States)

    Maulidin, Mahmuddin, M.; Kamaruddin, L. M.; Elsaikh, Mohamed

    2016-08-01

    Wireless Sensor Network (WSN) is a wireless network which consists of sensor nodes scattered in a particular area which are used to monitor physical or environment condition. Each node in WSN is also scattered in sensor field, so an appropriate scheme of MAC protocol should have to develop communication link for data transferring. Video transmission is one of the important applications for the future that can be transmitted with low aspect in side of cost and also power consumption. In this paper, comparison of five different MAC WSN protocol for video transmission namely IEEE 802.11 standard, IEEE 802.15.4 standard, CSMA/CA, Berkeley-MAC, and Lightweight-MAC protocol are studied. Simulation experiment has been conducted in OMNeT++ with INET network simulator software to evaluate the performance. Obtained results indicate that IEEE 802.11 works better than other protocol in term of packet delivery, throughput, and latency.

  9. Signaling-Free Max-Min Airtime Fairness in IEEE 802.11 Ad Hoc Networks

    Directory of Open Access Journals (Sweden)

    Youngsoo Lee

    2016-01-01

    Full Text Available We propose a novel media access control (MAC protocol, referred to as signaling-free max-min airtime fair (SMAF MAC, to improve fairness and channel utilization in ad hoc networks based on IEEE 802.11 wireless local area networks (WLANs. We introduce busy time ratio (BTR as a measure for max-min airtime fairness. Each node estimates its BTR and adjusts the transmission duration by means of frame aggregation and fragmentation, so that it can implicitly announce the BTR to neighbor nodes. Based on the announced BTR, each of the neighbor nodes controls its contention window. In this way, the SMAF MAC works in a distributed manner without the need to know the max-min fair share of airtime, and it does not require exchanging explicit control messages among nodes to attain fairness. Moreover, we successfully incorporate the hidden node detection and resolution mechanisms into the SMAF MAC to deal with the hidden node problem in ad hoc networks. The simulation results confirm that the SMAF MAC enhances airtime fairness without degrading channel utilization, and it effectively resolves several serious problems in ad hoc networks such as the starvation, performance anomaly, and hidden node problems.

  10. BER IMPROVEMENT OF WIRELESS LAN IEEE 802.11 STANDARD USING WAVELET PACKET TRANSFORMS

    Directory of Open Access Journals (Sweden)

    Sanjeev Kumar

    2012-09-01

    Full Text Available High data rates and spectral efficiency is the main requirements for wireless communication systems. Orthogonal Frequency Division Multiplexing (OFDM is a special form of multi carrier transmission used to achieve high data rates of the various WLAN standards. WLAN uses an Inverse Fast Fourier Transform (IFFT at the transmitter to modulate a high bit-rate signal onto a number of carriers and ensure orthogonality between the carriers. The FFT-OFDM has a disadvantage that it is inherently inflexible and requires a complex IFFT core. Recently, Wavelet Packet Transform is proposed as an alternate to FFT. It is a multiplexing method in which data is assigned to wavelet sub bands having different time and frequency resolutions. This paper presents a BER analysis of Fourier-based OFDM (FFT-OFDM and Wavelet Packet based OFDM (WPT-OFDM in WLAN standard (IEEE 802.11a. The performance of FFT and WPT OFDM for various modulation techniques such as PSK, DPSK and QAM for varying values of M was evaluated in AWGN Channel.

  11. Millimeter-wave Wireless LAN and its Extension toward 5G Heterogeneous Networks

    OpenAIRE

    Sakaguchi, Kei; Mohamed, Ehab Mahmoud; Kusano, Hideyuki; Mizukami, Makoto; Miyamoto, Shinichi; Rezagah, Roya; Takinami, Koji; Takahashi, Kazuaki; Shirakata, Naganori; Peng, Hailan; Yamamoto, Toshiaki; Namba, Shinobu

    2015-01-01

    Millimeter-wave (mmw) frequency bands, especially 60 GHz unlicensed band, are considered as a promising solution for gigabit short range wireless communication systems. IEEE standard 802.11ad, also known as WiGig, is standardized for the usage of the 60 GHz unlicensed band for wireless local area networks (WLANs). By using this mmw WLAN, multi-Gbps rate can be achieved to support bandwidth-intensive multimedia applications. Exhaustive search along with beamforming (BF) is usually used to over...

  12. A Multi-Channel Spectrum Sensing Fusion Mechanism for Cognitive Radio Networks: Design and Application to IEEE 802.22 WRANs

    OpenAIRE

    Tadayon, Navid; Aissa, Sonia

    2016-01-01

    The IEEE 802.22 is a new cognitive radio standard that is aimed at extending wireless outreach to rural areas. Known as wireless regional area networks, and designed based on the not-to-interfere spectrum sharing model, WRANs are channelized and centrally-controlled networks working on the under-utilized UHF/VHF TV bands to establish communication with remote users, so-called customer premises equipment (CPEs). Despite the importance of reliable and interference-free operation in these freque...

  13. Optimizing the MAC Protocol in Localization Systems Based on IEEE 802.15.4 Networks

    Directory of Open Access Journals (Sweden)

    Juan J. Pérez-Solano

    2017-07-01

    Full Text Available Radio frequency signals are commonly used in the development of indoor localization systems. The infrastructure of these systems includes some beacons placed at known positions that exchange radio packets with users to be located. When the system is implemented using wireless sensor networks, the wireless transceivers integrated in the network motes are usually based on the IEEE 802.15.4 standard. But, the CSMA-CA, which is the basis for the medium access protocols in this category of communication systems, is not suitable when several users want to exchange bursts of radio packets with the same beacon to acquire the radio signal strength indicator (RSSI values needed in the location process. Therefore, new protocols are necessary to avoid the packet collisions that appear when multiple users try to communicate with the same beacons. On the other hand, the RSSI sampling process should be carried out very quickly because some systems cannot tolerate a large delay in the location process. This is even more important when the RSSI sampling process includes measures with different signal power levels or frequency channels. The principal objective of this work is to speed up the RSSI sampling process in indoor localization systems. To achieve this objective, the main contribution is the proposal of a new MAC protocol that eliminates the medium access contention periods and decreases the number of packet collisions to accelerate the RSSI collection process. Moreover, the protocol increases the overall network throughput taking advantage of the frequency channel diversity. The presented results show the suitability of this protocol for reducing the RSSI gathering delay and increasing the network throughput in simulated and real environments.

  14. Optimizing the MAC Protocol in Localization Systems Based on IEEE 802.15.4 Networks.

    Science.gov (United States)

    Pérez-Solano, Juan J; Claver, Jose M; Ezpeleta, Santiago

    2017-07-06

    Radio frequency signals are commonly used in the development of indoor localization systems. The infrastructure of these systems includes some beacons placed at known positions that exchange radio packets with users to be located. When the system is implemented using wireless sensor networks, the wireless transceivers integrated in the network motes are usually based on the IEEE 802.15.4 standard. But, the CSMA-CA, which is the basis for the medium access protocols in this category of communication systems, is not suitable when several users want to exchange bursts of radio packets with the same beacon to acquire the radio signal strength indicator (RSSI) values needed in the location process. Therefore, new protocols are necessary to avoid the packet collisions that appear when multiple users try to communicate with the same beacons. On the other hand, the RSSI sampling process should be carried out very quickly because some systems cannot tolerate a large delay in the location process. This is even more important when the RSSI sampling process includes measures with different signal power levels or frequency channels. The principal objective of this work is to speed up the RSSI sampling process in indoor localization systems. To achieve this objective, the main contribution is the proposal of a new MAC protocol that eliminates the medium access contention periods and decreases the number of packet collisions to accelerate the RSSI collection process. Moreover, the protocol increases the overall network throughput taking advantage of the frequency channel diversity. The presented results show the suitability of this protocol for reducing the RSSI gathering delay and increasing the network throughput in simulated and real environments.

  15. Performance Analysis of IEEE 802.15.4 Compliant Wireless Devices for Heterogeneous Indoor Home Automation Environments

    Directory of Open Access Journals (Sweden)

    Juan Antonio Nazabal

    2012-01-01

    Full Text Available The influence of topology as well as morphology of complex indoor scenarios in the deployment of wireless sensor networks and wireless systems applied to home and building automation systems is analyzed. The existence of loss mechanisms such as material absorption (walls, furniture, etc. and strong multipath components as well as the increase in the number of wireless sensors within indoor scenarios increases the relevance in the configuration of the heterogeneous wireless systems. Simulation results by means of empirical-based models are compared with an in-house 3D ray launching code as well as measurement results from wireless sensor networks illustrate the strong influence of the indoor scenario in the overall performance. The use of adequate radioplanning strategies lead to optimal wireless network deployments in terms of capacity, quality of service, and reduced power consumption.

  16. Distributed medium access control in wireless networks

    CERN Document Server

    Wang, Ping

    2013-01-01

    This brief investigates distributed medium access control (MAC) with QoS provisioning for both single- and multi-hop wireless networks including wireless local area networks (WLANs), wireless ad hoc networks, and wireless mesh networks. For WLANs, an efficient MAC scheme and a call admission control algorithm are presented to provide guaranteed QoS for voice traffic and, at the same time, increase the voice capacity significantly compared with the current WLAN standard. In addition, a novel token-based scheduling scheme is proposed to provide great flexibility and facility to the network servi

  17. Weaponizing Wireless Networks

    DEFF Research Database (Denmark)

    Giannetsos, Athanasios; Tassos, Dimitriou; Prasad, Neeli R.

    2010-01-01

    of a sensor network. Results show that our tool can be flexibly applied to different sensor network operating systems and protocol stacks giving an adversary privileges to which she is not entitled to. We hope that our tool will be used proactively, to study the weaknesses of new security protocols, and......, hopefully, to enhance the level of security provided by these solutions even further....

  18. Isolan - A Fibre Optic Network Conforming To IEEE 802.3 Standards

    Science.gov (United States)

    Roworth, D. A. A.; Howe, N.

    1986-10-01

    The progress of the IEEE 802.3 standard for fibre optic LANs is indicated with reference to both mixed media networks and full fibre networks. For a fibre optic network the most suitable layout is a "snowflake" topology composed of multiport repeaters and active fibre hubs. A range of components is described which enables the realisation of such a topology in conformance with the IEEE 802.3 standard.

  19. Coexistence of IEEE 802.11b/g WLANs and IEEE 802.15.4 WSNs : Modeling and Protocol Enhancements

    NARCIS (Netherlands)

    Yuan, W.

    2011-01-01

    As an emerging short-range wireless technology, IEEE 802.15.4/ZigBee Wireless Sensor Networks (WSNs) are increasingly used in the fields of home control, industrial control, consumer electronics, energy management, building automation, telecom services, personal healthcare, etc. IEEE

  20. Distributed estimation based on observations prediction in wireless sensor networks

    KAUST Repository

    Bouchoucha, Taha

    2015-03-19

    We consider wireless sensor networks (WSNs) used for distributed estimation of unknown parameters. Due to the limited bandwidth, sensor nodes quantize their noisy observations before transmission to a fusion center (FC) for the estimation process. In this letter, the correlation between observations is exploited to reduce the mean-square error (MSE) of the distributed estimation. Specifically, sensor nodes generate local predictions of their observations and then transmit the quantized prediction errors (innovations) to the FC rather than the quantized observations. The analytic and numerical results show that transmitting the innovations rather than the observations mitigates the effect of quantization noise and hence reduces the MSE. © 2015 IEEE.

  1. Capacity Limit, Link Scheduling and Power Control in Wireless Networks

    Science.gov (United States)

    Zhou, Shan

    2013-01-01

    The rapid advancement of wireless technology has instigated the broad deployment of wireless networks. Different types of networks have been developed, including wireless sensor networks, mobile ad hoc networks, wireless local area networks, and cellular networks. These networks have different structures and applications, and require different…

  2. Preamble Structure for IEEE 802.11n Wireless LAN System

    Science.gov (United States)

    Aoki, Tsuguhide; Egashira, Yoshimasa; Takeda, Daisuke

    This paper proposes a preamble structure that raises the throughput of the physical layer of a MIMO-OFDM system that complies with IEEE 802.11n. The proposed preamble is based on two important criteria that have not been considered in conventional preamble structures but have an important bearing on realization of IEEE 802.11n. One is backward compatibility with legacy devices, such as IEEE 802.11a or IEEE 802.11g. The other is accurate AGC for MIMO data payload of the packet. Computer simulations and a laboratory test demonstrate that the proposed preamble is superior to the other preambles with respect to those two important criteria. The results were submitted to the task group N under the IEEE 802.11 working group and contributed to development of the current draft of IEEE 802.11n.

  3. A Mac Protocol Implementation for Wireless Sensor Network

    Directory of Open Access Journals (Sweden)

    Jamila Bhar

    2015-01-01

    Full Text Available IEEE 802.15.4 is an important standard for Low Rate Wireless Personal Area Network (LRWPAN. The IEEE 802.15.4 presents a flexible MAC protocol that provides good efficiency for data transmission by adapting its parameters according to characteristics of different applications. In this research work, some restrictions of this standard are explained and an improvement of traffic efficiency by optimizing MAC layer is proposed. Implementation details for several blocks of communication system are carefully modeled. The protocol implementation is done using VHDL language. The analysis gives a full understanding of the behavior of the MAC protocol with regard to backoff delay, data loss probability, congestion probability, slot effectiveness, and traffic distribution for terminals. Two ideas are proposed and tested to improve efficiency of CSMA/CA mechanism for IEEE 802.15.4 MAC Layer. Primarily, we dynamically adjust the backoff exponent (BE according to queue level of each node. Secondly, we vary the number of consecutive clear channel assessment (CCA for packet transmission. We demonstrate also that slot compensation provided by the enhanced MAC protocol can greatly avoid unused slots. The results show the significant improvements expected by our approach among the IEEE 802.15.4 MAC standards. Synthesis results show also hardware performances of our proposed architecture.

  4. A PROPOSED NOVEL ARCHITECTURE OF EC CONTROL SYSTEM USING IEEE 802.11n NETWORK AT ITER-INDIA GYROTRON TEST FACILITY

    Directory of Open Access Journals (Sweden)

    Deepak Mandge

    2017-06-01

    Full Text Available IEEE 802.11 Wi-Fi networks are increasingly becoming popular for its use in industrial applications. With the availability of recent amendments to IEEE 802.11 series of standards, particularly IEEE 802.11n, the adoption of Wi-Fi networks for process automation is gaining more focus and importance. The installation of Wireless networks naturally provides reduction in cable and its maintenance related costs, provides increased flexibility and mobility to enhance performance of industrial control system. The IEEE 802.11n supports parameterization that can be set for particular industrial applications and hence it has addressed to the aspects of timeliness and criticality to some extent. This paper proposes the use of IEEE 802.11n network to interconnect field instruments with Siemens PLC controller in harsh EMI/EMC environment. An application example is shown where the alternate control system architecture is developed in which non-critical and non-safety signals are communicated over Wi-Fi. While, for critical and safety signals, traditional hardwired signals methods can be implemented.

  5. On Throughput Improvement of Wireless Ad Hoc Networks with Hidden Nodes

    Science.gov (United States)

    Choi, Hong-Seok; Lim, Jong-Tae

    In this letter, we present the throughput analysis of the wireless ad hoc networks based on the IEEE 802.11 MAC (Medium Access Control). Especially, our analysis includes the case with the hidden node problem so that it can be applied to the multi-hop networks. In addition, we suggest a new channel access control algorithm to maximize the network throughput and show the usefulness of the proposed algorithm through simulations.

  6. Wireless Sensor Networks for Developmental and Flight Instrumentation

    Science.gov (United States)

    Alena, Richard; Figueroa, Fernando; Becker, Jeffrey; Foster, Mark; Wang, Ray; Gamudevelli, Suman; Studor, George

    2011-01-01

    Wireless sensor networks (WSN) based on the IEEE 802.15.4 Personal Area Network and ZigBee Pro 2007 standards are finding increasing use in home automation and smart energy markets providing a framework for interoperable software. The Wireless Connections in Space Project, funded by the NASA Engineering and Safety Center, is developing technology, metrics and requirements for next-generation spacecraft avionics incorporating wireless data transport. The team from Stennis Space Center and Mobitrum Corporation, working under a NASA SBIR grant, has developed techniques for embedding plug-and-play software into ZigBee WSN prototypes implementing the IEEE 1451 Transducer Electronic Datasheet (TEDS) standard. The TEDS provides meta-information regarding sensors such as serial number, calibration curve and operational status. Incorporation of TEDS into wireless sensors leads directly to building application level software that can recognize sensors at run-time, dynamically instantiating sensors as they are added or removed. The Ames Research Center team has been experimenting with this technology building demonstration prototypes for on-board health monitoring. Innovations in technology, software and process can lead to dramatic improvements for managing sensor systems applied to Developmental and Flight Instrumentation (DFI) aboard aerospace vehicles. A brief overview of the plug-and-play ZigBee WSN technology is presented along with specific targets for application within the aerospace DFI market. The software architecture for the sensor nodes incorporating the TEDS information is described along with the functions of the Network Capable Gateway processor which bridges 802.15.4 PAN to the TCP/IP network. Client application software connects to the Gateway and is used to display TEDS information and real-time sensor data values updated every few seconds, incorporating error detection and logging to help measure performance and reliability in relevant target environments

  7. Impact Of Mobility and Transmission Range On The Performance of Backoff Algorithms For IEEE 802.11-Based Multi-hop Mobile Ad hoc Networks

    OpenAIRE

    Saini, Pooja

    2010-01-01

    In IEEE 802.11 Wireless Local Area Networks (WLANs), network nodes experiencing collisions on the shared channel need to backoff for a random period of time, which is uniformly selected from the Contention Window (CW). This contention window is dynamically controlled by the Backoff algorithm. First step to design a an efficient backoff algorithm for multi-hop ad hoc network is to analysis of the existing backoff algorithms in multi-hop ad hoc networks. Thus, in this paper, we considered two i...

  8. Fiber optics backbone for IEEE 802.3 networks

    Science.gov (United States)

    Shani, Ron

    1990-01-01

    In the last few years the IEEE 802.3 committee has developed fiber optics inter-repeater link standard called FOIRL. This standard defines the "Fiber Optics Media Access Unit" (FOMAU) which is used to connect two IEEE 802.3 repeaters that are up to 1Km apart. The IEEE 802.3 lOBaseF task force is currently standardizing a full F/O system in two directions: passive and active. The active approach is a compromise between the FOIRL (Asynchronous) approach and the Synchronous approach. As a result of this activity the IEEE 802.3 standard will define three different F/O interfaces and several devices that will not inter-operate. Such a standard will lower the credibility among the IEEE 802.3 user community, as customers will be confused amidst the many chapters and devices with no clear choice. This paper describes a method that can reduce the number of standards to two (passive and active), while proposing a solution for all the requirements of 802.3 F/O LAN. (The question of passive vs active approach will be discussed in this paper).

  9. Filtering and control of wireless networked systems

    CERN Document Server

    Zhang, Dan; Yu, Li

    2017-01-01

    This self-contained book, written by leading experts, offers a cutting-edge, in-depth overview of the filtering and control of wireless networked systems. It addresses the energy constraint and filter/controller gain variation problems, and presents both the centralized and the distributed solutions. The first two chapters provide an introduction to networked control systems and basic information on system analysis. Chapters (3–6) then discuss the centralized filtering of wireless networked systems, presenting different approaches to deal with energy efficiency and filter/controller gain variation problems. The next part (chapters 7–10) explores the distributed filtering of wireless networked systems, addressing the main problems of energy constraint and filter gain variation. The final part (chapters 11–14) focuses on the distributed control of wireless networked systems. wireless networked systems for communication and control applications, the bo...

  10. Voice Quality Estimation in Wireless Networks

    Directory of Open Access Journals (Sweden)

    Petr Zach

    2015-01-01

    Full Text Available This article deals with the impact of Wireless (Wi-Fi networks on the perceived quality of voice services. The Quality of Service (QoS metrics must be monitored in the computer network during the voice data transmission to ensure proper voice service quality the end-user has paid for, especially in the wireless networks. In addition to the QoS, research area called Quality of Experience (QoE provides metrics and methods for quality evaluation from the end-user’s perspective. This article focuses on a QoE estimation of Voice over IP (VoIP calls in the wireless networks using network simulator. Results contribute to voice quality estimation based on characteristics of the wireless network and location of a wireless client.

  11. Reliability of Wireless Sensor Networks

    Science.gov (United States)

    Dâmaso, Antônio; Rosa, Nelson; Maciel, Paulo

    2014-01-01

    Wireless Sensor Networks (WSNs) consist of hundreds or thousands of sensor nodes with limited processing, storage, and battery capabilities. There are several strategies to reduce the power consumption of WSN nodes (by increasing the network lifetime) and increase the reliability of the network (by improving the WSN Quality of Service). However, there is an inherent conflict between power consumption and reliability: an increase in reliability usually leads to an increase in power consumption. For example, routing algorithms can send the same packet though different paths (multipath strategy), which it is important for reliability, but they significantly increase the WSN power consumption. In this context, this paper proposes a model for evaluating the reliability of WSNs considering the battery level as a key factor. Moreover, this model is based on routing algorithms used by WSNs. In order to evaluate the proposed models, three scenarios were considered to show the impact of the power consumption on the reliability of WSNs. PMID:25157553

  12. Outage probability analysis of wireless sensor networks in the presence of channel fading and spatial correlation

    KAUST Repository

    Al-Murad, Tamim M.

    2011-07-01

    Evaluating the reliability of wireless sensor networks is becoming more important as theses networks are being used in crucial applications. The outage probability defined as the probability that the error in the system exceeds a maximum acceptable threshold has recently been used as a measure of the reliability of such systems. In this work we find the outage probability of wireless sensor network in different scenarios of distributed sensing where sensors\\' readings are affected by spatial correlation and in the presence of channel fading. © 2011 IEEE.

  13. Topological properties of random wireless networks

    Indian Academy of Sciences (India)

    Wireless networks in which the node locations are random are best modelled as random geometric graphs (RGGs). In addition to their extensive application in the modelling of wireless networks, RGGs find many new applications and are being studied in their own right. In this paper we first provide a brief introduction to the ...

  14. Performance Analysis of IIUM Wireless Campus Network

    International Nuclear Information System (INIS)

    Latif, Suhaimi Abd; Masud, Mosharrof H; Anwar, Farhat

    2013-01-01

    International Islamic University Malaysia (IIUM) is one of the leading universities in the world in terms of quality of education that has been achieved due to providing numerous facilities including wireless services to every enrolled student. The quality of this wireless service is controlled and monitored by Information Technology Division (ITD), an ISO standardized organization under the university. This paper aims to investigate the constraints of wireless campus network of IIUM. It evaluates the performance of the IIUM wireless campus network in terms of delay, throughput and jitter. QualNet 5.2 simulator tool has employed to measure these performances of IIUM wireless campus network. The observation from the simulation result could be one of the influencing factors in improving wireless services for ITD and further improvement

  15. IEEE 802.15.4 MAC with GTS transmission for heterogeneous devices with application to wheelchair body-area sensor networks.

    Science.gov (United States)

    Shrestha, Bharat; Hossain, Ekram; Camorlinga, Sergio

    2011-09-01

    In wireless personal area networks, such as wireless body-area sensor networks, stations or devices have different bandwidth requirements and, thus, create heterogeneous traffics. For such networks, the IEEE 802.15.4 medium access control (MAC) can be used in the beacon-enabled mode, which supports guaranteed time slot (GTS) allocation for time-critical data transmissions. This paper presents a general discrete-time Markov chain model for the IEEE 802.15.4-based networks taking into account the slotted carrier sense multiple access with collision avoidance and GTS transmission phenomena together in the heterogeneous traffic scenario and under nonsaturated condition. For this purpose, the standard GTS allocation scheme is modified. For each non-identical device, the Markov model is solved and the average service time and the service utilization factor are analyzed in the non-saturated mode. The analysis is validated by simulations using network simulator version 2.33. Also, the model is enhanced with a wireless propagation model and the performance of the MAC is evaluated in a wheelchair body-area sensor network scenario.

  16. Persistent RCSMA: A MAC Protocol for a Distributed Cooperative ARQ Scheme in Wireless Networks

    Directory of Open Access Journals (Sweden)

    J. Alonso-Zárate

    2008-05-01

    Full Text Available The persistent relay carrier sensing multiple access (PRCSMA protocol is presented in this paper as a novel medium access control (MAC protocol that allows for the execution of a distributed cooperative automatic retransmission request (ARQ scheme in IEEE 802.11 wireless networks. The underlying idea of the PRCSMA protocol is to modify the basic rules of the IEEE 802.11 MAC protocol to execute a distributed cooperative ARQ scheme in wireless networks in order to enhance their performance and to extend coverage. A closed formulation of the distributed cooperative ARQ average packet transmission delay in a saturated network is derived in the paper. The analytical equations are then used to evaluate the performance of the protocol under different network configurations. Both the accuracy of the analysis and the performance evaluation of the protocol are supported and validated through computer simulations.

  17. Service Differentiation in OFDM-Based IEEE 802.16 Networks

    Directory of Open Access Journals (Sweden)

    2009-03-01

    Full Text Available IEEE 802.16 network is widely viewed as a strong candidate solution for broadband wireless access systems. Various flexible mechanisms related to QoS provisioning have been specified for uplink traffic at the medium access control (MAC layer in the standards. Among the mechanisms, bandwidth request scheme can be used to indicate and request bandwidth demands to the base station for different services. Due to the diverse QoS requirements of the applications, service differentiation (SD is desirable for the bandwidth request scheme. In this paper, we propose several SD approaches. The approaches are based on the contention-based bandwidth request scheme and achieved by the means of assigning different channel access parameters and/or bandwidth allocation priorities to different services. Additionally, we propose effective analytical model to study the impacts of the SD approaches, which can be used for the configuration and optimization of the SD services. It is observed from simulations that the analytical model has high accuracy. Service can be efficiently differentiated with initial backoff window in terms of throughput and channel access delay. Moreover, the service differentiation can be improved if combined with the bandwidth allocation priority approach without adverse impacts on the overall system throughput.

  18. An Enhanced Reservation-Based MAC Protocol for IEEE 802.15.4 Networks

    Science.gov (United States)

    Afonso, José A.; Silva, Helder D.; Macedo, Pedro; Rocha, Luis A.

    2011-01-01

    The IEEE 802.15.4 Medium Access Control (MAC) protocol is an enabling standard for wireless sensor networks. In order to support applications requiring dedicated bandwidth or bounded delay, it provides a reservation-based scheme named Guaranteed Time Slot (GTS). However, the GTS scheme presents some drawbacks, such as inefficient bandwidth utilization and support to a maximum of only seven devices. This paper presents eLPRT (enhanced Low Power Real Time), a new reservation-based MAC protocol that introduces several performance enhancing features in comparison to the GTS scheme. This MAC protocol builds on top of LPRT (Low Power Real Time) and includes various mechanisms designed to increase data transmission reliability against channel errors, improve bandwidth utilization and increase the number of supported devices. A motion capture system based on inertial and magnetic sensors has been used to validate the protocol. The effectiveness of the performance enhancements introduced by each of the new features is demonstrated through the provision of both simulation and experimental results. PMID:22163826

  19. Adaptive Naive Bayes classification for wireless sensor networks

    NARCIS (Netherlands)

    Zwartjes, G.J.

    2017-01-01

    Wireless Sensor Networks are tiny devices equipped with sensors and wireless communication. These devices observe environments and communicatie about these observations. Machine Learning techniques are of interest for Wireless Sensor Network applications since they can reduce the amount of needed

  20. Distributed wireless quantum communication networks

    International Nuclear Information System (INIS)

    Yu Xu-Tao; Xu Jin; Zhang Zai-Chen

    2013-01-01

    The distributed wireless quantum communication network (DWQCN) has a distributed network topology and transmits information by quantum states. In this paper, we present the concept of the DWQCN and propose a system scheme to transfer quantum states in the DWQCN. The system scheme for transmitting information between any two nodes in the DWQCN includes a routing protocol and a scheme for transferring quantum states. The routing protocol is on-demand and the routing metric is selected based on the number of entangled particle pairs. After setting up a route, quantum teleportation and entanglement swapping are used for transferring quantum states. Entanglement swapping is achieved along with the process of routing set up and the acknowledgment packet transmission. The measurement results of each entanglement swapping are piggybacked with route reply packets or acknowledgment packets. After entanglement swapping, a direct quantum link between source and destination is set up and quantum states are transferred by quantum teleportation. Adopting this scheme, the measurement results of entanglement swapping do not need to be transmitted specially, which decreases the wireless transmission cost and transmission delay. (general)

  1. How to model wireless mesh networks topology

    International Nuclear Information System (INIS)

    Sanni, M L; Hashim, A A; Anwar, F; Ali, S; Ahmed, G S M

    2013-01-01

    The specification of network connectivity model or topology is the beginning of design and analysis in Computer Network researches. Wireless Mesh Networks is an autonomic network that is dynamically self-organised, self-configured while the mesh nodes establish automatic connectivity with the adjacent nodes in the relay network of wireless backbone routers. Researches in Wireless Mesh Networks range from node deployment to internetworking issues with sensor, Internet and cellular networks. These researches require modelling of relationships and interactions among nodes including technical characteristics of the links while satisfying the architectural requirements of the physical network. However, the existing topology generators model geographic topologies which constitute different architectures, thus may not be suitable in Wireless Mesh Networks scenarios. The existing methods of topology generation are explored, analysed and parameters for their characterisation are identified. Furthermore, an algorithm for the design of Wireless Mesh Networks topology based on square grid model is proposed in this paper. The performance of the topology generated is also evaluated. This research is particularly important in the generation of a close-to-real topology for ensuring relevance of design to the intended network and validity of results obtained in Wireless Mesh Networks researches

  2. Self-Coexistence among IEEE 802.22 Networks: Distributed Allocation of Power and Channel

    OpenAIRE

    Sayef Azad Sakin; Md. Abdur Razzaque; Mohammad Mehedi Hassan; Atif Alamri; Nguyen H. Tran; Giancarlo Fortino

    2017-01-01

    Ensuring self-coexistence among IEEE 802.22 networks is a challenging problem owing to opportunistic access of incumbent-free radio resources by users in co-located networks. In this study, we propose a fully-distributed non-cooperative approach to ensure self-coexistence in downlink channels of IEEE 802.22 networks. We formulate the self-coexistence problem as a mixed-integer non-linear optimization problem for maximizing the network data rate, which is an NP-hard one. This work explores a s...

  3. Implementation of a wireless ECG acquisition SoC for IEEE 802.15.4 (ZigBee) applications.

    Science.gov (United States)

    Wang, Liang-Hung; Chen, Tsung-Yen; Lin, Kuang-Hao; Fang, Qiang; Lee, Shuenn-Yuh

    2015-01-01

    This paper presents a wireless biosignal acquisition system-on-a-chip (WBSA-SoC) specialized for electrocardiogram (ECG) monitoring. The proposed system consists of three subsystems, namely, 1) the ECG acquisition node, 2) the protocol for standard IEEE 802.15.4 ZigBee system, and 3) the RF transmitter circuits. The ZigBee protocol is adopted for wireless communication to achieve high integration, applicability, and portability. A fully integrated CMOS RF front end containing a quadrature voltage-controlled oscillator and a 2.4-GHz low-IF (i.e., zero-IF) transmitter is employed to transmit ECG signals through wireless communication. The low-power WBSA-SoC is implemented by the TSMC 0.18-μm standard CMOS process. An ARM-based displayer with FPGA demodulation and an RF receiver with analog-to-digital mixed-mode circuits are constructed as verification platform to demonstrate the wireless ECG acquisition system. Measurement results on the human body show that the proposed SoC can effectively acquire ECG signals.

  4. Voice over IP in Wireless Heterogeneous Networks

    DEFF Research Database (Denmark)

    Fathi, Hanane; Chakraborty, Shyam; Prasad, Ramjee

    The convergence of different types of traffic has preceded the convergence of systems and services in a wireless heterogeneous network. Voice and data traffic are usually treated separate in both 2G and 2.5G wireless networks. With advances in packet switching technology and especially with the d...... and to the discruption caused by the user mobility during the session. Voice over IP in Wireless Hetetrogeneous Networks thus investigates and proposes cross-layer techniques for realizing time-efficient control mechanisms for VoIP: signaling, mobility and security.......The convergence of different types of traffic has preceded the convergence of systems and services in a wireless heterogeneous network. Voice and data traffic are usually treated separate in both 2G and 2.5G wireless networks. With advances in packet switching technology and especially...... with the deployment of wireless heterogeneous systems, both speech and data traffic are carrried over wireless links by the same IP-based packet-switched infrastructure. However, this combination faces some challenges due to the inherent properties of the wireless network. The requirements for good quality Vo...

  5. Defending IEEE 802.11-Based Networks Against Denial Of Service Attacks

    National Research Council Canada - National Science Library

    Tan, Boon

    2003-01-01

    ...) attacks targeting its management and media access protocols Computer simulation models have proven to be effective tools in the study of cause and effect in numerous fields This thesis involved the design and implementation of a IEEE 8O2.11-based simulation model using OMNeT++, to investigate the effects of different types of DoS attacks on a IEEE 8O2.11 network, and the effectiveness of corresponding countermeasures.

  6. Optimal modulation and coding scheme allocation of scalable video multicast over IEEE 802.16e networks

    Directory of Open Access Journals (Sweden)

    Tsai Chia-Tai

    2011-01-01

    Full Text Available Abstract With the rapid development of wireless communication technology and the rapid increase in demand for network bandwidth, IEEE 802.16e is an emerging network technique that has been deployed in many metropolises. In addition to the features of high data rate and large coverage, it also enables scalable video multicasting, which is a potentially promising application, over an IEEE 802.16e network. How to optimally assign the modulation and coding scheme (MCS of the scalable video stream for the mobile subscriber stations to improve spectral efficiency and maximize utility is a crucial task. We formulate this MCS assignment problem as an optimization problem, called the total utility maximization problem (TUMP. This article transforms the TUMP into a precedence constraint knapsack problem, which is a NP-complete problem. Then, a branch and bound method, which is based on two dominance rules and a lower bound, is presented to solve the TUMP. The simulation results show that the proposed branch and bound method can find the optimal solution efficiently.

  7. Proxy SDN Controller for Wireless Networks

    Directory of Open Access Journals (Sweden)

    Won-Suk Kim

    2016-01-01

    Full Text Available Management of wireless networks as well as wired networks by using software-defined networking (SDN has been highlighted continually. However, control features of a wireless network differ from those of a wired network in several aspects. In this study, we identify the various inefficient points when controlling and managing wireless networks by using SDN and propose SDN-based control architecture called Proxcon to resolve these problems. Proxcon introduces the concept of a proxy SDN controller (PSC for the wireless network control, and the PSC entrusted with the role of a main controller performs control operations and provides the latest network state for a network administrator. To address the control inefficiency, Proxcon supports offloaded SDN operations for controlling wireless networks by utilizing the PSC, such as local control by each PSC, hybrid control utilizing the PSC and the main controller, and locally cooperative control utilizing the PSCs. The proposed architecture and the newly supported control operations can enhance scalability and response time when the logically centralized control plane responds to the various wireless network events. Through actual experiments, we verified that the proposed architecture could address the various control issues such as scalability, response time, and control overhead.

  8. The Design of Wireless Sensor Network System Based on ZigBee Technology for Greenhouse

    Science.gov (United States)

    Zhu, Y. W.; Zhong, X. X.; Shi, J. F.

    2006-10-01

    Wireless sensor network is a new research field. It can be used in some special situation for signal collection, processing and transmitting. Zigbee is a new Wireless sensor network technology characteristic of less distance and low speed. It is a new wireless network protocol stack of IEEE 802.15.4. Lately traditional system to collects parameters for Greenhouse is widely used in agriculture. The traditional system adopts wired way wiring, which makes the system complex and expensive. Generally modern Greenhouse has hundreds of square meters and they may plant variety of plants depending on different seasons. So we need to adjust the sensors which collect parameters for Greenhouse to a better place to work more efficient. Adopting wireless way wiring is convenient and economical. This paper developed a wireless sensor network system based on ZigBee technology for greenhouse. It offers flexibility and mobility to save cost and energy spent on wiring. The framework hardware and software structure, related programming are also discussed in this paper. Comparing the system which uses ZigBee technology with traditional wired network system for greenhouse, it has advantage of low cost..low power and wider coverage. Additionally it complies with IEEE802.15.4 protocol, which makes it convenient to communicate with other products that comply with the protocol too.

  9. The Design of Wireless Sensor Network System Based on ZigBee Technology for Greenhouse

    International Nuclear Information System (INIS)

    Zhu, Y W; Zhong, X X; Shi, J F

    2006-01-01

    Wireless sensor network is a new research field. It can be used in some special situation for signal collection, processing and transmitting. Zigbee is a new Wireless sensor network technology characteristic of less distance and low speed. It is a new wireless network protocol stack of IEEE 802.15.4. Lately traditional system to collects parameters for Greenhouse is widely used in agriculture. The traditional system adopts wired way wiring, which makes the system complex and expensive. Generally modern Greenhouse has hundreds of square meters and they may plant variety of plants depending on different seasons. So we need to adjust the sensors which collect parameters for Greenhouse to a better place to work more efficient. Adopting wireless way wiring is convenient and economical. This paper developed a wireless sensor network system based on ZigBee technology for greenhouse. It offers flexibility and mobility to save cost and energy spent on wiring. The framework hardware and software structure, related programming are also discussed in this paper. Comparing the system which uses ZigBee technology with traditional wired network system for greenhouse, it has advantage of low cost..low power and wider coverage. Additionally it complies with IEEE802.15.4 protocol, which makes it convenient to communicate with other products that comply with the protocol too

  10. The art of wireless sensor networks

    CERN Document Server

    2014-01-01

    During the last one and a half decades, wireless sensor networks have witnessed significant growth and tremendous development in both academia and industry.   “The Art of Wireless Sensor Networks: Volume 1: Fundamentals” focuses on the fundamentals concepts in the design, analysis, and implementation of wireless sensor networks. It covers the various layers of the lifecycle of this type of network from the physical layer up to the application layer. Its rationale is that the first volume covers contemporary design issues, tools, and protocols for radio-based two-dimensional terrestrial sensor networks. All the book chapters in this volume include up-to-date research work spanning various classic facets of the physical properties and functional behavior of wireless sensor networks, including physical layer, medium access control, data routing, topology management, mobility management, localization, task management, data management, data gathering, security, middleware, sensor technology, standards, and ...

  11. Interference Mitigation in IEEE 802.15.4-A Cluster Based Scheduling Approach

    OpenAIRE

    G. M. Tamilselvan; A. Shanmugam

    2011-01-01

    Problem statement: In universal networking environments; two or more heterogeneous communication systems coexisting in a single place. Especially, Wireless Local Area Networks (WLANs) based on IEEE 802.11b specifications and Wireless Personal Area Networks (WPANs) based on IEEE 802.15.4 specifications need to coexist in the same Industrial, Science and Medial (ISM) band. If the WPAN communication coverage is expanded using a cluster-tree network topology, then the 802...

  12. BackTrack testing wireless network security

    CERN Document Server

    Cardwell, Kevin

    2013-01-01

    Written in an easy-to-follow step-by-step format, you will be able to get started in next to no time with minimal effort and zero fuss.BackTrack: Testing Wireless Network Security is for anyone who has an interest in security and who wants to know more about wireless networks.All you need is some experience with networks and computers and you will be ready to go.

  13. Wireless communications networks for the smart grid

    CERN Document Server

    Ho, Quang-Dung; Rajalingham, Gowdemy; Le-Ngoc, Tho

    2014-01-01

    This brief presents a comprehensive review of the network architecture and communication technologies of the smart grid communication network (SGCN). It then studies the strengths, weaknesses and applications of two promising wireless mesh routing protocols that could be used to implement the SGCN. Packet transmission reliability, latency and robustness of these two protocols are evaluated and compared by simulations in various practical SGCN scenarios. Finally, technical challenges and open research opportunities of the SGCN are addressed. Wireless Communications Networks for Smart Grid provi

  14. Performance Evaluation of IEEE 802.11ah Networks With High-Throughput Bidirectional Traffic.

    Science.gov (United States)

    Šljivo, Amina; Kerkhove, Dwight; Tian, Le; Famaey, Jeroen; Munteanu, Adrian; Moerman, Ingrid; Hoebeke, Jeroen; De Poorter, Eli

    2018-01-23

    So far, existing sub-GHz wireless communication technologies focused on low-bandwidth, long-range communication with large numbers of constrained devices. Although these characteristics are fine for many Internet of Things (IoT) applications, more demanding application requirements could not be met and legacy Internet technologies such as Transmission Control Protocol/Internet Protocol (TCP/IP) could not be used. This has changed with the advent of the new IEEE 802.11ah Wi-Fi standard, which is much more suitable for reliable bidirectional communication and high-throughput applications over a wide area (up to 1 km). The standard offers great possibilities for network performance optimization through a number of physical- and link-layer configurable features. However, given that the optimal configuration parameters depend on traffic patterns, the standard does not dictate how to determine them. Such a large number of configuration options can lead to sub-optimal or even incorrect configurations. Therefore, we investigated how two key mechanisms, Restricted Access Window (RAW) grouping and Traffic Indication Map (TIM) segmentation, influence scalability, throughput, latency and energy efficiency in the presence of bidirectional TCP/IP traffic. We considered both high-throughput video streaming traffic and large-scale reliable sensing traffic and investigated TCP behavior in both scenarios when the link layer introduces long delays. This article presents the relations between attainable throughput per station and attainable number of stations, as well as the influence of RAW, TIM and TCP parameters on both. We found that up to 20 continuously streaming IP-cameras can be reliably connected via IEEE 802.11ah with a maximum average data rate of 160 kbps, whereas 10 IP-cameras can achieve average data rates of up to 255 kbps over 200 m. Up to 6960 stations transmitting every 60 s can be connected over 1 km with no lost packets. The presented results enable the fine tuning

  15. Opportunistic Beacon Networks: Information Dissemination via Wireless Network Identifiers

    NARCIS (Netherlands)

    Türkes, Okan; Scholten, Johan; Havinga, Paul J.M.

    2016-01-01

    This paper presents OBN, a universal opportunistic ad hoc networking model particularly intended for smart mobile devices. It enables fast and lightweight data dissemination in wireless community networks through the utilization of universally-available wireless network identifiers. As a ubiquitous

  16. Time and Energy Efficient Relay Transmission for Multi-Hop Wireless Sensor Networks.

    Science.gov (United States)

    Kim, Jin-Woo; Barrado, José Ramón Ramos; Jeon, Dong-Keun

    2016-06-27

    The IEEE 802.15.4 standard is widely recognized as one of the most successful enabling technologies for short range low rate wireless communications and it is used in IoT applications. It covers all the details related to the MAC and PHY layers of the IoT protocol stack. Due to the nature of IoT, the wireless sensor networks are autonomously self-organized networks without infrastructure support. One of the issues in IoT is the network scalability. To address this issue, it is necessary to support the multi-hop topology. The IEEE 802.15.4 network can support a star, peer-to-peer, or cluster-tree topology. One of the IEEE 802.15.4 topologies suited for the high predictability of performance guarantees and energy efficient behavior is a cluster-tree topology where sensor nodes can switch off their transceivers and go into a sleep state to save energy. However, the IEEE 802.15.4 cluster-tree topology may not be able to provide sufficient bandwidth for the increased traffic load and the additional information may not be delivered successfully. The common drawback of the existing approaches is that they do not address the poor bandwidth utilization problem in IEEE 802.15.4 cluster-tree networks, so it is difficult to increase the network performance. Therefore, to solve this problem in this paper we study a relay transmission protocol based on the standard protocol in the IEEE 802.15.4 MAC. In the proposed scheme, the coordinators can relay data frames to their parent devices or their children devices without contention and can provide bandwidth for the increased traffic load or the number of devices. We also evaluate the performance of the proposed scheme through simulation. The simulation results demonstrate that the proposed scheme can improve the reliability, the end-to-end delay, and the energy consumption.

  17. Time and Energy Efficient Relay Transmission for Multi-Hop Wireless Sensor Networks

    Directory of Open Access Journals (Sweden)

    Jin-Woo Kim

    2016-06-01

    Full Text Available The IEEE 802.15.4 standard is widely recognized as one of the most successful enabling technologies for short range low rate wireless communications and it is used in IoT applications. It covers all the details related to the MAC and PHY layers of the IoT protocol stack. Due to the nature of IoT, the wireless sensor networks are autonomously self-organized networks without infrastructure support. One of the issues in IoT is the network scalability. To address this issue, it is necessary to support the multi-hop topology. The IEEE 802.15.4 network can support a star, peer-to-peer, or cluster-tree topology. One of the IEEE 802.15.4 topologies suited for the high predictability of performance guarantees and energy efficient behavior is a cluster-tree topology where sensor nodes can switch off their transceivers and go into a sleep state to save energy. However, the IEEE 802.15.4 cluster-tree topology may not be able to provide sufficient bandwidth for the increased traffic load and the additional information may not be delivered successfully. The common drawback of the existing approaches is that they do not address the poor bandwidth utilization problem in IEEE 802.15.4 cluster-tree networks, so it is difficult to increase the network performance. Therefore, to solve this problem in this paper we study a relay transmission protocol based on the standard protocol in the IEEE 802.15.4 MAC. In the proposed scheme, the coordinators can relay data frames to their parent devices or their children devices without contention and can provide bandwidth for the increased traffic load or the number of devices. We also evaluate the performance of the proposed scheme through simulation. The simulation results demonstrate that the proposed scheme can improve the reliability, the end-to-end delay, and the energy consumption.

  18. Analysis and Testing of Mobile Wireless Networks

    Science.gov (United States)

    Alena, Richard; Evenson, Darin; Rundquist, Victor; Clancy, Daniel (Technical Monitor)

    2002-01-01

    Wireless networks are being used to connect mobile computing elements in more applications as the technology matures. There are now many products (such as 802.11 and 802.11b) which ran in the ISM frequency band and comply with wireless network standards. They are being used increasingly to link mobile Intranet into Wired networks. Standard methods of analyzing and testing their performance and compatibility are needed to determine the limits of the technology. This paper presents analytical and experimental methods of determining network throughput, range and coverage, and interference sources. Both radio frequency (BE) domain and network domain analysis have been applied to determine wireless network throughput and range in the outdoor environment- Comparison of field test data taken under optimal conditions, with performance predicted from RF analysis, yielded quantitative results applicable to future designs. Layering multiple wireless network- sooners can increase performance. Wireless network components can be set to different radio frequency-hopping sequences or spreading functions, allowing more than one sooner to coexist. Therefore, we ran multiple 802.11-compliant systems concurrently in the same geographical area to determine interference effects and scalability, The results can be used to design of more robust networks which have multiple layers of wireless data communication paths and provide increased throughput overall.

  19. A guide to wireless networking by light

    Science.gov (United States)

    Haas, Harald; Chen, Cheng; O'Brien, Dominic

    2017-09-01

    The lack of wireless spectrum in the radio frequency bands has led to a rapid growth in research in wireless networking using light, known as LiFi (light fidelity). In this paper an overview of the subsystems, challenges and techniques required to achieve this is presented.

  20. Performance Analysis of Non-saturated IEEE 802.11 DCF Networks

    Science.gov (United States)

    Zhai, Linbo; Zhang, Xiaomin; Xie, Gang

    This letter presents a model with queueing theory to analyze the performance of non-saturated IEEE 802.11 DCF networks. We use the closed queueing network model and derive an approximate representation of throughput which can reveal the relationship between the throughput and the total offered load under finite traffic load conditions. The accuracy of the model is verified by extensive simulations.

  1. Improving the communication reliability of body sensor networks based on the IEEE 802.15.4 protocol.

    Science.gov (United States)

    Gomes, Diogo; Afonso, José A

    2014-03-01

    Body sensor networks (BSNs) enable continuous monitoring of patients anywhere, with minimum constraints to daily life activities. Although the IEEE 802.15.4 and ZigBee(®) (ZigBee Alliance, San Ramon, CA) standards were mainly developed for use in wireless sensors network (WSN) applications, they are also widely used in BSN applications because of device characteristics such as low power, low cost, and small form factor. However, compared with WSNs, BSNs present some very distinctive characteristics in terms of traffic and mobility patterns, heterogeneity of the nodes, and quality of service requirements. This article evaluates the suitability of the carrier sense multiple access-collision avoidance protocol, used by the IEEE 802.15.4 and ZigBee standards, for data-intensive BSN applications, through the execution of experimental tests in different evaluation scenarios, in order to take into account the effects of contention, clock drift, and hidden nodes on the communication reliability. Results show that the delivery ratio may decrease substantially during transitory periods, which can last for several minutes, to a minimum of 90% with retransmissions and 13% without retransmissions. This article also proposes and evaluates the performance of the BSN contention avoidance mechanism, which was designed to solve the identified reliability problems. This mechanism was able to restore the delivery ratio to 100% even in the scenario without retransmissions.

  2. Wireless sensor networks for indoor air quality monitoring.

    Science.gov (United States)

    Yu, Tsang-Chu; Lin, Chung-Chih; Chen, Chun-Chang; Lee, Wei-Lun; Lee, Ren-Guey; Tseng, Chao-Heng; Liu, Shi-Ping

    2013-02-01

    The purpose of this study is to build an indoor air quality monitoring system based on wireless sensor networks (WSNs) technology. The main functions of the system include (1) remote parameter adjustment and firmware update mechanism for the sensors to enhance the flexibility and convenience of the system, (2) sensor nodes are designed by referring to the IEEE 1451.4 standard. This way, sensor nodes can automatically adjust and be plug and play, and (3) calibration method to strength the measurement value's sensitivity and accuracy. The experimental results show that transmission speed improves 30% than Trickle, transmission volume reduced to 42% of the original volume, updating task in 5*5 network topology can be executed 1.79 times and power consumption reduced to 30%. When baseline drifts, we can use the firmware update mechanism to adjust the reference value. The way can reduce error percentage from 15% to 7%. Copyright © 2011 IPEM. Published by Elsevier Ltd. All rights reserved.

  3. Configuration of Wireless Cooperative/Sensor Networks

    National Research Council Canada - National Science Library

    Shafiee, Hamid R; Maham, B; Vazifehdan, J

    2008-01-01

    .... When employing more than one antenna at each node of a wireless network is not applicable, cooperation diversity protocols exploit the inherent spatial diversity of relay channels by allowing mobile...

  4. Intelligent Wireless Sensor Networks for System Health Monitoring

    Science.gov (United States)

    Alena, Rick

    2011-01-01

    Wireless sensor networks (WSN) based on the IEEE 802.15.4 Personal Area Network (PAN) standard are finding increasing use in the home automation and emerging smart energy markets. The network and application layers, based on the ZigBee 2007 Standard, provide a convenient framework for component-based software that supports customer solutions from multiple vendors. WSNs provide the inherent fault tolerance required for aerospace applications. The Discovery and Systems Health Group at NASA Ames Research Center has been developing WSN technology for use aboard aircraft and spacecraft for System Health Monitoring of structures and life support systems using funding from the NASA Engineering and Safety Center and Exploration Technology Development and Demonstration Program. This technology provides key advantages for low-power, low-cost ancillary sensing systems particularly across pressure interfaces and in areas where it is difficult to run wires. Intelligence for sensor networks could be defined as the capability of forming dynamic sensor networks, allowing high-level application software to identify and address any sensor that joined the network without the use of any centralized database defining the sensors characteristics. The IEEE 1451 Standard defines methods for the management of intelligent sensor systems and the IEEE 1451.4 section defines Transducer Electronic Datasheets (TEDS), which contain key information regarding the sensor characteristics such as name, description, serial number, calibration information and user information such as location within a vehicle. By locating the TEDS information on the wireless sensor itself and enabling access to this information base from the application software, the application can identify the sensor unambiguously and interpret and present the sensor data stream without reference to any other information. The application software is able to read the status of each sensor module, responding in real-time to changes of

  5. Optimal Throughput and Self-adaptability of Robust Real-Time IEEE 802.15.4 MAC for AMI Mesh Network

    International Nuclear Information System (INIS)

    Shabani, Hikma; Ahmed, Musse Mohamud; Khan, Sheroz; Hameed, Shahab Ahmed; Habaebi, Mohamed Hadi

    2013-01-01

    A smart grid refers to a modernization of the electricity system that brings intelligence, reliability, efficiency and optimality to the power grid. To provide an automated and widely distributed energy delivery, the smart grid will be branded by a two-way flow of electricity and information system between energy suppliers and their customers. Thus, the smart grid is a power grid that integrates data communication networks which provide the collected and analysed data at all levels in real time. Therefore, the performance of communication systems is so vital for the success of smart grid. Merit to the ZigBee/IEEE802.15.4std low cost, low power, low data rate, short range, simplicity and free licensed spectrum that makes wireless sensor networks (WSNs) the most suitable wireless technology for smart grid applications. Unfortunately, almost all ZigBee channels overlap with wireless local area network (WLAN) channels, resulting in severe performance degradation due to interference. In order to improve the performance of communication systems, this paper proposes an optimal throughput and self-adaptability of ZigBee/IEEE802.15.4std for smart grid

  6. Optimal Throughput and Self-adaptability of Robust Real-Time IEEE 802.15.4 MAC for AMI Mesh Network

    Science.gov (United States)

    Shabani, Hikma; Mohamud Ahmed, Musse; Khan, Sheroz; Hameed, Shahab Ahmed; Hadi Habaebi, Mohamed

    2013-12-01

    A smart grid refers to a modernization of the electricity system that brings intelligence, reliability, efficiency and optimality to the power grid. To provide an automated and widely distributed energy delivery, the smart grid will be branded by a two-way flow of electricity and information system between energy suppliers and their customers. Thus, the smart grid is a power grid that integrates data communication networks which provide the collected and analysed data at all levels in real time. Therefore, the performance of communication systems is so vital for the success of smart grid. Merit to the ZigBee/IEEE802.15.4std low cost, low power, low data rate, short range, simplicity and free licensed spectrum that makes wireless sensor networks (WSNs) the most suitable wireless technology for smart grid applications. Unfortunately, almost all ZigBee channels overlap with wireless local area network (WLAN) channels, resulting in severe performance degradation due to interference. In order to improve the performance of communication systems, this paper proposes an optimal throughput and self-adaptability of ZigBee/IEEE802.15.4std for smart grid.

  7. Availability Issues in Wireless Visual Sensor Networks

    Science.gov (United States)

    Costa, Daniel G.; Silva, Ivanovitch; Guedes, Luiz Affonso; Vasques, Francisco; Portugal, Paulo

    2014-01-01

    Wireless visual sensor networks have been considered for a large set of monitoring applications related with surveillance, tracking and multipurpose visual monitoring. When sensors are deployed over a monitored field, permanent faults may happen during the network lifetime, reducing the monitoring quality or rendering parts or the entire network unavailable. In a different way from scalar sensor networks, camera-enabled sensors collect information following a directional sensing model, which changes the notions of vicinity and redundancy. Moreover, visual source nodes may have different relevancies for the applications, according to the monitoring requirements and cameras' poses. In this paper we discuss the most relevant availability issues related to wireless visual sensor networks, addressing availability evaluation and enhancement. Such discussions are valuable when designing, deploying and managing wireless visual sensor networks, bringing significant contributions to these networks. PMID:24526301

  8. Multi-level infrastructure of interconnected testbeds of large-scale wireless sensor networks (MI2T-WSN)

    CSIR Research Space (South Africa)

    Abu-Mahfouz, Adnan M

    2012-06-01

    Full Text Available , October 14-16, Tokyo, Japan, 2008, pp. 1-5. [6] G. Werner-Allen, K. Lorincz, M. Ruiz, O. Marcillo, J. Johnson, J. Lees and M. Welsh, "Deploying a wireless sensor network on an active volcano," IEEE Internet Computing, vol. 10, no. 2, pp. 18-25. 2006...

  9. On the Conditional Entropy of Wireless Networks

    DEFF Research Database (Denmark)

    Coon, Justin P.; Badiu, Mihai Alin; Gündüz, Deniz

    2018-01-01

    The characterization of topological uncertainty in wireless networks using the formalism of graph entropy has received interest in the spatial networks community. In this paper, we develop lower bounds on the entropy of a wireless network by conditioning on potential network observables. Two...... approaches are considered: 1) conditioning on subgraphs, and 2) conditioning on node positions. The first approach is shown to yield a relatively tight bound on the network entropy. The second yields a loose bound, in general, but it provides insight into the dependence between node positions (modelled using...

  10. Topology Optimisation of Wireless Sensor Networks

    Directory of Open Access Journals (Sweden)

    Thike Aye Min

    2016-01-01

    Full Text Available Wireless sensor networks are widely used in a variety of fields including industrial environments. In case of a clustered network the location of cluster head affects the reliability of the network operation. Finding of the optimum location of the cluster head, therefore, is critical for the design of a network. This paper discusses the optimisation approach, based on the brute force algorithm, in the context of topology optimisation of a cluster structure centralised wireless sensor network. Two examples are given to verify the approach that demonstrate the implementation of the brute force algorithm to find an optimum location of the cluster head.

  11. Implementation of DoS attack and mitigation strategies in IEEE 802.11b/g WLAN

    Science.gov (United States)

    Deng, Julia; Meng, Ke; Xiao, Yang; Xu, Roger

    2010-04-01

    IEEE 802.11 wireless Local Area Network (WLAN) becomes very prevalent nowadays. Either as a simple range extender for a home wired Ethernet interface, or as a wireless deployment throughout an enterprise, WLAN provides mobility, convenience, and low cost. However, an IEEE 802.11b/g wireless network uses the frequency of unlicensed 2.4GHz, which makes the network unsafe and more vulnerable than traditional Ethernet networks. As a result, anyone who is familiar with wireless network may initiate a Denial of Service (DoS) attack to influence the common communication of the network or even make it crash. In this paper, we present our studies on the DoS attacks and mitigation strategies for IEEE 802.11b/g WLANs and describe some initial implementations using IEEE 802.11b/g wireless devices.

  12. Software-defined networking model for smart transformers with ISO/IEC/IEEE 21451 sensors

    Directory of Open Access Journals (Sweden)

    Longhua Guo

    2017-06-01

    Full Text Available The advanced IEC 61850 smart transformer has shown an improved performance in monitoring, controlling, and protecting the equipment in smart substations. However, heterogeneity, feasibility, and network control problems have limited the smart transformer’s performance in networks. To address these issues, a software-defined networking model was proposed using ISO/IEC/IEEE 21451 networks. An IEC-61850-based network controller was designed as a new kind of intelligent electrical device (IED. The proposed data and information models enhanced the network awareness ability and facilitated the access of smart sensors in transformer to communication networks. The performance evaluation results showed an improved efficiency.

  13. Matching theory for wireless networks

    CERN Document Server

    Han, Zhu; Saad, Walid

    2017-01-01

    This book provides the fundamental knowledge of the classical matching theory problems. It builds up the bridge between the matching theory and the 5G wireless communication resource allocation problems. The potentials and challenges of implementing the semi-distributive matching theory framework into the wireless resource allocations are analyzed both theoretically and through implementation examples. Academics, researchers, engineers, and so on, who are interested in efficient distributive wireless resource allocation solutions, will find this book to be an exceptional resource. .

  14. Utilising artificial intelligence in software defined wireless sensor network

    CSIR Research Space (South Africa)

    Matlou, OG

    2017-10-01

    Full Text Available Software Defined Wireless Sensor Network (SDWSN) is realised by infusing Software Defined Network (SDN) model in Wireless Sensor Network (WSN), Reason for that is to overcome the challenges of WSN. Artificial Intelligence (AI) and machine learning...

  15. Throughput Analysis of Primary and Secondary Networks in a Shared IEEE 802.11 System

    OpenAIRE

    Kumar, Santhosh; Shende, Nirmal; Murthy, Chandra R.; Ayyagari, Arun

    2012-01-01

    In this paper, we analyze the coexistence of a primary and a secondary (cognitive) network when both networks use the IEEE 802.11 based distributed coordination function for medium access control. Specifically, we consider the problem of channel capture by a secondary network that uses spectrum sensing to determine the availability of the channel, and its impact on the primary throughput. We integrate the notion of transmission slots in Bianchi's Markov model with the physical time slots, to ...

  16. Performance Evaluation of Quality of Service in IEEE 802.11e Wireless LANs

    Science.gov (United States)

    Peng, Fei; Leung, Victor C. M.

    There have been many performance studies on the original IEEE 802.11 distributed coordinated function using both simulation and analytical methods. However, the recent IEEE 802.11e standard has not yet been investigated extensively. This paper proposes an accurate analytical model for the enhanced distributed channel access (EDCA), which is the core protocol of 802.11e. The model captures the operations of service differentiation using different contention window (CW) sizes, arbitrary interframe space (AIFS), and transmission opportunity (TXOP) limits in EDCA. Using this model, we derive throughput performance of EDCA access categories differentiated through the above mechanisms. The throughput and collision probability derived by our model are validated by simulation results, which show close agreements with the analytical results. Our model provides a useful tool for evaluating the impact of different parameters on the performance of EDCA service differentiation.

  17. Group-Orthogonal Code-Division Multiplex: A Physical-Layer Enhancement for IEEE 802.11n Networks

    Directory of Open Access Journals (Sweden)

    Felip Riera-Palou

    2010-01-01

    Full Text Available The new standard for wireless local area networks (WLANs, named IEEE 802.11n, has been recently released. This new norm builds upon and remains compatible with the previous WLANs standards IEEE 802.11a/g while it is able to achieve transmission rates of up to 600 Mbps. These increased data rates are mainly a consequence of two important new features: (1 multiple antenna technology at transmission and reception, and (2 optional doubling of the system bandwidth thanks to the availability of an additional 20 MHz band. This paper proposes the use of Group-Orthogonal Code Division Multiplex (GO-CDM as a means to improve the performance of the 802.11n standard by further exploiting the inherent frequency diversity. It is explained why GO-CDM synergistically matches with the two aforementioned new features and the performance gains it can offer under different configurations is illustrated. Furthermore, the effects that group-orthogonal has on key implementation issues such as channel estimation, carrier frequency offset, and peak-to-average power ratio (PAPR are also considered.

  18. Towards Controlling Latency in Wireless Networks

    KAUST Repository

    Bouacida, Nader

    2017-04-24

    Wireless networks are undergoing an unprecedented revolution in the last decade. With the explosion of delay-sensitive applications in the Internet (i.e., online gaming and VoIP), latency becomes a major issue for the development of wireless technology. Taking advantage of the significant decline in memory prices, industrialists equip the network devices with larger buffering capacities to improve the network throughput by limiting packets drops. Over-buffering results in increasing the time that packets spend in the queues and, thus, introducing more latency in networks. This phenomenon is known as “bufferbloat”. While throughput is the dominant performance metric, latency also has a huge impact on user experience not only for real-time applications but also for common applications like web browsing, which is sensitive to latencies in order of hundreds of milliseconds. Concerns have arisen about designing sophisticated queue management schemes to mitigate the effects of such phenomenon. My thesis research aims to solve bufferbloat problem in both traditional half-duplex and cutting-edge full-duplex wireless systems by reducing delay while maximizing wireless links utilization and fairness. Our work shed lights on buffer management algorithms behavior in wireless networks and their ability to reduce latency resulting from excessive queuing delays inside oversized static network buffers without a significant loss in other network metrics. First of all, we address the problem of buffer management in wireless full-duplex networks by using Wireless Queue Management (WQM), which is an active queue management technique for wireless networks. Our solution is based on Relay Full-Duplex MAC (RFD-MAC), an asynchronous media access control protocol designed for relay full-duplexing. Compared to the default case, our solution reduces the end-to-end delay by two orders of magnitude while achieving similar throughput in most of the cases. In the second part of this thesis

  19. Wireless Sensor Node Power Profiling Based on IEEE 802.11 and IEEE 802.15.4 Communication Protocols. Modeling and Simulation

    Energy Technology Data Exchange (ETDEWEB)

    Agarwal, Vivek [Idaho National Lab. (INL), Idaho Falls, ID (United States); Richardson, Joseph [Idaho National Lab. (INL), Idaho Falls, ID (United States); Zhang, Yanliang [Idaho National Lab. (INL), Idaho Falls, ID (United States)

    2015-10-01

    Most wireless sensor network (comprising of thousands of WSNs) applications require operation over extended periods of time beginning with their deployment. Network lifetime is extremely critical for most applications and is one of the limiting factors for energy-constrained networks. Based on applications, there are wide ranges of different energy sources suitable for powering WSNs. A battery is traditionally used to power WSNs. The deployed WSN is required to last for long time. Due to finite amount of energy present in batteries, it is not feasible to replace batteries. Recently there has been a new surge in the area of energy harvesting were ambient energy in the environment can be utilized to prolong the lifetime of WSNs. Some of the sources of ambient energies are solar power, thermal gradient, human motion and body heat, vibrations, and ambient RF energy. The design and development of TEGs to power WSNs that would remain active for a long period of time requires comprehensive understanding of WSN operational. This motivates the research in modeling the lifetime, i.e., power consumption, of a WSN by taking into consideration various node and network level activities. A WSN must perform three essential tasks: sense events, perform quick local information processing of sensed events, and wirelessly exchange locally processed data with the base station or with other WSNs in the network. Each task has a power cost per unit tine and an additional cost when switching between tasks. There are number of other considerations that must also be taken into account when computing the power consumption associated with each task. The considerations includes: number of events occurring in a fixed active time period and the duration of each event, event-information processing time, total communication time, number of retransmission, etc. Additionally, at the network level the communication of information data packets between WSNs involves collisions, latency, and

  20. Routing protocols in wireless sensor networks.

    Science.gov (United States)

    Villalba, Luis Javier García; Orozco, Ana Lucila Sandoval; Cabrera, Alicia Triviño; Abbas, Cláudia Jacy Barenco

    2009-01-01

    The applications of wireless sensor networks comprise a wide variety of scenarios. In most of them, the network is composed of a significant number of nodes deployed in an extensive area in which not all nodes are directly connected. Then, the data exchange is supported by multihop communications. Routing protocols are in charge of discovering and maintaining the routes in the network. However, the appropriateness of a particular routing protocol mainly depends on the capabilities of the nodes and on the application requirements. This paper presents a review of the main routing protocols proposed for wireless sensor networks. Additionally, the paper includes the efforts carried out by Spanish universities on developing optimization techniques in the area of routing protocols for wireless sensor networks.

  1. Performance Modeling of a Bottleneck Node in an IEEE 802.11 Ad-hoc Network

    NARCIS (Netherlands)

    van den Berg, Hans Leo; Roijers, Frank; Mandjes, M.R.H.; Kunz, Thomas; Ravi, S.S.

    2006-01-01

    The IEEE 802.11 MAC protocol, often used in ad-hoc networks, has the tendency to share the capacity equally amongst the active nodes, irrespective of their loads. An inherent drawback of this fair-sharing policy is that a node that serves as a relay-node for multiple flows is likely to become a

  2. Adaptive Probabilistic Broadcasting over Dense Wireless Ad Hoc Networks

    Directory of Open Access Journals (Sweden)

    Victor Gau

    2010-01-01

    Full Text Available We propose an idle probability-based broadcasting method, iPro, which employs an adaptive probabilistic mechanism to improve performance of data broadcasting over dense wireless ad hoc networks. In multisource one-hop broadcast scenarios, the modeling and simulation results of the proposed iPro are shown to significantly outperform the standard IEEE 802.11 under saturated condition. Moreover, the results also show that without estimating the number of competing nodes and changing the contention window size, the performance of the proposed iPro can still approach the theoretical bound. We further apply iPro to multihop broadcasting scenarios, and the experiment results show that within the same elapsed time after the broadcasting, the proposed iPro has significantly higher Packet-Delivery Ratios (PDR than traditional methods.

  3. Structural health monitoring using wireless sensor networks

    Science.gov (United States)

    Sreevallabhan, K.; Nikhil Chand, B.; Ramasamy, Sudha

    2017-11-01

    Monitoring and analysing health of large structures like bridges, dams, buildings and heavy machinery is important for safety, economical, operational, making prior protective measures, and repair and maintenance point of view. In recent years there is growing demand for such larger structures which in turn make people focus more on safety. By using Microelectromechanical Systems (MEMS) Accelerometer we can perform Structural Health Monitoring by studying the dynamic response through measure of ambient vibrations and strong motion of such structures. By using Wireless Sensor Networks (WSN) we can embed these sensors in wireless networks which helps us to transmit data wirelessly thus we can measure the data wirelessly at any remote location. This in turn reduces heavy wiring which is a cost effective as well as time consuming process to lay those wires. In this paper we developed WSN based MEMS-accelerometer for Structural to test the results in the railway bridge near VIT University, Vellore campus.

  4. Sensor Fusion-based Event Detection in Wireless Sensor Networks

    NARCIS (Netherlands)

    Bahrepour, M.; Meratnia, Nirvana; Havinga, Paul J.M.

    2009-01-01

    Recently, Wireless Sensor Networks (WSN) community has witnessed an application focus shift. Although, monitoring was the initial application of wireless sensor networks, in-network data processing and (near) real-time actuation capability have made wireless sensor networks suitable candidate for

  5. Wireless Security Within Hastily Formed Networks

    Science.gov (United States)

    2006-09-01

    Layer 3, creates an IPSec tunnel , much like a VPN , to protect the wireless point to point link as shown above independent of the wireless...2006) say the two most popular VPN implementations, IPSec (IP Security) and SSL (Secure Sockets Layer), each have their own strengths and weaknesses...Protocol (L2TP) Layer 3 (Network Layer) • Point-to-Point Tunneling Protocol (PPTP) • IP Security ( IPSec ) Layer 7 (Applications Layer) • Secure

  6. Robust resource allocation in future wireless networks

    CERN Document Server

    Parsaeefard, Saeedeh; Mokari, Nader

    2017-01-01

    This book presents state-of-the-art research on robust resource allocation in current and future wireless networks. The authors describe the nominal resource allocation problems in wireless networks and explain why introducing robustness in such networks is desirable. Then, depending on the objectives of the problem, namely maximizing the social utility or the per-user utility, cooperative or competitive approaches are explained and their corresponding robust problems are considered in detail. For each approach, the costs and benefits of robust schemes are discussed and the algorithms for reducing their costs and improving their benefits are presented. Considering the fact that such problems are inherently non-convex and intractable, a taxonomy of different relaxation techniques is presented, and applications of such techniques are shown via several examples throughout the book. Finally, the authors argue that resource allocation continues to be an important issue in future wireless networks, and propose spec...

  7. Evaluation of H.264/AVC over IEEE 802.11p vehicular networks

    Science.gov (United States)

    Rozas-Ramallal, Ismael; Fernández-Caramés, Tiago M.; Dapena, Adriana; García-Naya, José Antonio

    2013-12-01

    The capacity of vehicular networks to offer non-safety services, like infotainment applications or the exchange of multimedia information between vehicles, have attracted a great deal of attention to the field of Intelligent Transport Systems (ITS). In particular, in this article we focus our attention on IEEE 802.11p which defines enhancements to IEEE 802.11 required to support ITS applications. We present an FPGA-based testbed developed to evaluate H.264/AVC (Advanced Video Coding) video transmission over vehicular networks. The testbed covers some of the most common situations in vehicle-to-vehicle and roadside-to-vehicle communications and it is highly flexible, allowing the performance evaluation of different vehicular standard configurations. We also show several experimental results to illustrate the quality obtained when H.264/AVC encoded video is transmitted over IEEE 802.11p networks. The quality is measured considering two important parameters: the percentage of recovered group of pictures and the frame quality. In order to improve performance, we propose to substitute the convolutional channel encoder used in IEEE 802.11p for a low-density parity-check code encoder. In addition, we suggest a simple strategy to decide the optimum number of iterations needed to decode each packet received.

  8. Wireless vehicular networks for car collision avoidance

    CERN Document Server

    2013-01-01

    Wireless Vehicular Networks for Car Collision Avoidance focuses on the development of the ITS (Intelligent Transportation Systems) in order to minimize vehicular accidents. The book presents and analyses a range of concrete accident scenarios while examining the causes of vehicular collision and proposing countermeasures based on wireless vehicular networks. The book also describes the vehicular network standards and quality of service mechanisms focusing on improving critical dissemination of safety information. With recommendations on techniques and protocols to consider when improving road safety policies in order to minimize crashes and collision risks.

  9. Troubleshooting Assistance Services in Community Wireless Networks

    Directory of Open Access Journals (Sweden)

    P. Kriz

    2012-01-01

    Full Text Available We have identified new services intended for users and administrators of community wireless networks. Troubleshooting assistance services will assist the users during solution of communication problems, gathering data for expert analysis, informing the user about the state of the network (including outages, and so forth. Network administrators will be provided with a unique tool supporting the network analysis, operation, and development. We have mainly focused on the use cases and prerequirements—the problem of topology discovery.

  10. Topological properties of random wireless networks

    Indian Academy of Sciences (India)

    http://www.ias.ac.in/article/fulltext/sadh/031/02/0117-0139 ... Abstract. Wireless networks in which the node locations are random are best modelled as random geometric graphs (RGGs). ... We then discuss some asymptotic results for networks in higher dimensions when the nodes are distributed in a finite volume. Finally ...

  11. Wireless Wide Area Networks for School Districts.

    Science.gov (United States)

    Nair, Prakash

    This paper considers a basic question that many schools districts face in attempting to develop affordable, expandable district-wide computer networks that are resistant to obsolescence: Should these wide area networks (WANs) employ wireless technology, stick to venerable hard-wired solutions, or combine both. This publication explores the…

  12. Wireless Sensor Networks TestBed: ASNTbed

    CSIR Research Space (South Africa)

    Dludla, AG

    2013-05-01

    Full Text Available -1 IST-Africa 2013 Conference Proceedings, Nairobi, Kenya, 29 - 31 May 2013 Wireless Sensor Networks TestBed: ASNTbed Angeline G. DLUDLA, Adnan M. ABU-MAHFOUZ, Carel P. KRUGER, John S. ISAAC Advanced Sensor Networks Research Group, CSIR Meraka...

  13. Collaborative communication protocols for wireless sensor networks

    NARCIS (Netherlands)

    Dulman, S.O.; van Hoesel, L.F.W.; Nieberg, T.; Havinga, Paul J.M.

    In this document, the design of communication within a wireless sensor network is discussed. The resource limitations of such a network, especially in terms of energy, require an integrated approach for all (traditional) layers of communication. We present such an integrated, collaborative approach

  14. Service discovery in heterogeneous wireless networks

    NARCIS (Netherlands)

    Blangé, M.J.; Karkowski, I.P.; Vermeulen, B.C.B.

    2005-01-01

    In this paper we describe a possible solution to the problem of service discovery in heterogeneous wireless networks. This solution involves introduction of a network independent service discovery layer, with as main goal the improved robustness of applications running on top of it. A possible

  15. Advanced Wireless Integrated Navy Network

    National Research Council Canada - National Science Library

    Stutzman, Warren; Habayeb, Rick

    2005-01-01

    Quarterly progress report No. I on AWINN hardware and software configurations of smart, wideband, multi-function antennas, secure configurable platform, close-in command and control for Sea Basing visualization of wireless...

  16. Flexible network wireless transceiver and flexible network telemetry transceiver

    Science.gov (United States)

    Brown, Kenneth D.

    2008-08-05

    A transceiver for facilitating two-way wireless communication between a baseband application and other nodes in a wireless network, wherein the transceiver provides baseband communication networking and necessary configuration and control functions along with transmitter, receiver, and antenna functions to enable the wireless communication. More specifically, the transceiver provides a long-range wireless duplex communication node or channel between the baseband application, which is associated with a mobile or fixed space, air, water, or ground vehicle or other platform, and other nodes in the wireless network or grid. The transceiver broadly comprises a communication processor; a flexible telemetry transceiver including a receiver and a transmitter; a power conversion and regulation mechanism; a diplexer; and a phased array antenna system, wherein these various components and certain subcomponents thereof may be separately enclosed and distributable relative to the other components and subcomponents.

  17. Interference-Robust Transmission in Wireless Sensor Networks.

    Science.gov (United States)

    Han, Jin-Seok; Lee, Yong-Hwan

    2016-11-14

    Low-power wireless sensor networks (WSNs) operating in unlicensed spectrum bands may seriously suffer from interference from other coexisting radio systems, such as IEEE 802.11 wireless local area networks. In this paper, we consider the improvement of the transmission performance of low-power WSNs by adjusting the transmission rate and the payload size in response to the change of co-channel interference. We estimate the probability of transmission failure and the data throughput and then determine the payload size to maximize the throughput performance. We investigate that the transmission time maximizing the normalized throughput is not much affected by the transmission rate, but rather by the interference condition. We adjust the transmission rate and the transmission time in response to the change of the channel and interference condition, respectively. Finally, we verify the performance of the proposed scheme by computer simulation. The simulation results show that the proposed scheme significantly improves data throughput compared with conventional schemes while preserving energy efficiency even in the presence of interference.

  18. Efficient Wireless Charger Deployment for Wireless Rechargeable Sensor Networks

    Directory of Open Access Journals (Sweden)

    Jehn-Ruey Jiang

    2016-08-01

    Full Text Available A wireless rechargeable sensor network (WRSN consists of sensor nodes that can harvest energy emitted from wireless chargers for refilling their batteries so that the WRSN can operate sustainably. This paper assumes wireless chargers are equipped with directional antennas, and are deployed on grid points of a fixed height to propose two heuristic algorithms solving the following wireless charger deployment optimization (WCDO problem: how to deploy as few as possible chargers to make the WRSN sustainable. Both algorithms model the charging space of chargers as a cone and calculate charging efficiency according power regression expressions complying with the Friis transmission equation. The two algorithms are the greedy cone covering (GCC algorithm and the adaptive cone covering (ACC algorithm. The GCC (respectively, ACC algorithm greedily (respectively, adaptively generates candidate cones to cover as many as possible sensor nodes. Both algorithms then greedily select the fewest number of candidate cones, each of which corresponds to the deployment of a charger, to have approximate solutions to the WCDO problem. We perform experiments, conduct simulations and do analyses for the algorithms to compare them in terms of the time complexity, the number of chargers deployed, and the execution time.

  19. Cooperative Jamming for Physical Layer Security in Wireless Sensor Networks

    DEFF Research Database (Denmark)

    Rohokale, Vandana M.; Prasad, Neeli R.; Prasad, Ramjee

    2012-01-01

    Interference is generally considered as the redundant and unwanted occurrence in wireless communication. This work proposes a novel cooperative jamming mechanism for scalable networks like Wireless Sensor Networks (WSNs) which makes use of friendly interference to confuse the eavesdropper...

  20. Artificial intelligence based event detection in wireless sensor networks

    NARCIS (Netherlands)

    Bahrepour, M.

    2013-01-01

    Wireless sensor networks (WSNs) are composed of large number of small, inexpensive devices, called sensor nodes, which are equipped with sensing, processing, and communication capabilities. While traditional applications of wireless sensor networks focused on periodic monitoring, the focus of more

  1. Intrusion detection in wireless ad-hoc networks

    CERN Document Server

    Chaki, Nabendu

    2014-01-01

    Presenting cutting-edge research, Intrusion Detection in Wireless Ad-Hoc Networks explores the security aspects of the basic categories of wireless ad-hoc networks and related application areas. Focusing on intrusion detection systems (IDSs), it explains how to establish security solutions for the range of wireless networks, including mobile ad-hoc networks, hybrid wireless networks, and sensor networks.This edited volume reviews and analyzes state-of-the-art IDSs for various wireless ad-hoc networks. It includes case studies on honesty-based intrusion detection systems, cluster oriented-based

  2. Energy Efficient Wireless Sensor Network Modelling Based on Complex Networks

    OpenAIRE

    Xiao, Lin; Wu, Fahui; Yang, Dingcheng; Zhang, Tiankui; Zhu, Xiaoya

    2016-01-01

    The power consumption and energy efficiency of wireless sensor network are the significant problems in Internet of Things network. In this paper, we consider the network topology optimization based on complex network theory to solve the energy efficiency problem of WSN. We propose the energy efficient model of WSN according to the basic principle of small world from complex networks. Small world network has clustering features that are similar to that of the rules of the network but also has ...

  3. Implementation of mobile ip smooth handoff in wireless networks

    International Nuclear Information System (INIS)

    Kayastha, M.; Chowdhry, B.S.; Memon, A.R.

    2002-01-01

    This paper describes implementation of mobile IP services in two separate wireless LANs based on IEEE 802.11b standards, located in two distant buildings of a university campus. The purpose of the project was to achieve smooth hand-off when a mobile node moves between the two LANs. During our experimentation we have identified some of the limitation of IEEE 802.11b that affects mobile 1P smooth hand off. We have also proposed an algorithm to solve this problem when the mobility is within a limited number of separate wireless LANs. (author)

  4. Applying Game Theory in 802.11 Wireless Networks

    Directory of Open Access Journals (Sweden)

    Tomas Cuzanauskas

    2015-07-01

    Full Text Available IEEE 802.11 is one of the most popular wireless technologies in recent days. Due to easiness of adaption and relatively low cost the demand for IEEE 802.11 devices is increasing exponentially. IEEE works in two bands 2.4 GHz and 5 GHz, these bands are known as ISM band. The unlicensed bands are managed by authority which set simple rules to follow when using unlicensed bands, the rules includes requirements as maximum power, out-of-band emissions control as well as interference mitigation. However these rules became outdated as IEEE 802.11 technology is emerging and evolving in hours the rules aren’t well suited for current capabilities of IEEE 802.11 devices. In this article we present game theory based algorithm for IEEE 802.11 wireless devices, we will show that by using game theory it’s possible to achieve better usage of unlicensed spectrum as well as partially decline CSMA/CA. Finally by using this approach we might relax the currently applied maximum power rules for ISM bands, which enable IEEE 802.11 to work on longer distance and have better propagation characteristics.

  5. Ad hoc mobile wireless networks principles, protocols, and applications

    CERN Document Server

    Sarkar, Subir Kumar

    2013-01-01

    The military, the research community, emergency services, and industrial environments all rely on ad hoc mobile wireless networks because of their simple infrastructure and minimal central administration. Now in its second edition, Ad Hoc Mobile Wireless Networks: Principles, Protocols, and Applications explains the concepts, mechanism, design, and performance of these highly valued systems. Following an overview of wireless network fundamentals, the book explores MAC layer, routing, multicast, and transport layer protocols for ad hoc mobile wireless networks. Next, it examines quality of serv

  6. Low-Power Wireless Sensor Network Infrastructures

    DEFF Research Database (Denmark)

    Hansen, Morten Tranberg

    Advancements in wireless communication and electronics improving form factor and hardware capabilities has expanded the applicability of wireless sensor networks. Despite these advancements, devices are still limited in terms of energy which creates the need for duty-cycling and low-power protocols...... peripherals need to by duty-cycled and the low-power wireless radios are severely influenced by the environmental effects causing bursty and unreliable wireless channels. This dissertation presents a communication stack providing services for low-power communication, secure communication, data collection...... channel. Second, secure communication is implemented with an efficient secure group communication suite including a low-overhead group key distribution scheme, distributing group keys according to the needs of the sensor nodes. Third, data collection is implemented with selective transmission which saves...

  7. WQM: An Aggregation-aware Queue Management Scheme for IEEE 802.11n based Networks

    KAUST Repository

    Showail, Ahmad

    2014-08-17

    Choosing the right buffer size in Wi-Fi networks is challenging due to the dynamic nature of the wireless environment. Over buffering or \\'bufferbloat\\' may produce unacceptable end-to-end delays, while static small buffers may limit the performance gains that can be achieved with various 802.11n enhancements, such as frame aggregation. We propose WQM, a queue management scheme customized for wireless networks. WQM adapts the buffer size based on measured link characteristics and network load. Furthermore, it accounts for aggregate length when deciding about the optimal buffer size. We implement WQM on Linux and evaluate it on a wireless testbed. WQM reduces the end-to-end delay by up to 8x compared to Linux default buffer size, and 2x compared to CoDel, the state-of-the-art bufferbloat solution, while achieving comparable network goodput. Further, WQM improves fairness as it limits the ability of a single flow to saturate the buffer.

  8. Energy-Harvesting Wireless Sensor Networks

    DEFF Research Database (Denmark)

    Fafoutis, Xenofon; Vuckovic, Dusan; Di Mauro, Alessio

    2012-01-01

    Energy Harvesting comprises a promising solution to one of the key problems faced by battery-powered Wireless Sensor Networks, namely the limited nature of the energy supply (finite battery capacity). By harvesting energy from the surrounding environment, the sensors can have a continuous lifetime...... without any needs for battery recharge or replacement. However, energy harvesting introduces a change to the fundamental principles based on which WSNs are designed and realized. In this poster we sketch some of the key research challenges as well as our ongoing work in designing and realizing Wireless...... Sensor Networks with energy harvesting capability....

  9. Stochastic petri nets for wireless networks

    CERN Document Server

    Lei, Lei; Zhong, Zhangdui

    2015-01-01

    This SpringerBrief presents research in the application of Stochastic Petri Nets (SPN) to the performance evaluation of wireless networks under bursty traffic. It covers typical Quality-of-Service performance metrics such as mean throughput, average delay and packet dropping probability. Along with an introduction of SPN basics, the authors introduce the key motivation and challenges of using SPN to analyze the resource sharing performance in wireless networks. The authors explain two powerful modeling techniques that treat the well-known state space explosion problem: model decomposition and

  10. Wireless Fidelity (Wi-Fi) Broadband Network Technology: An ...

    African Journals Online (AJOL)

    Wireless Fidelity (Wi-Fi) broadband network technology has made tremendous impact in the growth of broadband wireless networks. There exists today several Wi-Fi access points that allow employees, partners and customers to access corporate data from almost anywhere and anytime. Wireless broadband networks are ...

  11. Low-power wireless sensor networks for environmental monitoring

    Science.gov (United States)

    Musaloiu-Elefteri, Razvan

    Significant progress has been made in the field of Wireless Sensor Networks in the decade that passed since its inception. This thesis presents several advances intended to make these networks a suitable instrument for environmental monitoring. The thesis first describes Koala, a low-power data-retrieval system that can achieve duty cycles below 1% by using bulk transfers, and Low Power Probing, a novel mechanism to efficiently wake up a network. The second contribution is Serendipity, another data-retrieval system, which takes advantage of the random rendezvous inherent in the Low Power Probing mechanism to achieve a very low duty cycle for low data rate networks. The third part explores the problem of and presents a solution for the interference between WSNs using IEEE 802.15.4 radios and the ubiquitous WiFi networks in the 2.4 GHz spectrum bandwidth. The last contribution of this thesis is Latte, a restricted version of the JavaScript language, that not only can be compiled to C and dynamically loaded on a sensing node, but can also be simulated and debugged in a JavaScript-enabled browser.

  12. Future Wireless Networks and Information Systems Volume 1

    CERN Document Server

    2012-01-01

    This volume contains revised and extended research articles written by prominent researchers participating in ICFWI 2011 conference. The 2011 International Conference on Future Wireless Networks and Information Systems (ICFWI 2011) has been held on November 30 ~ December 1, 2011, Macao, China. Topics covered include Wireless Information Networks, Wireless Networking Technologies, Mobile Software and Services, intelligent computing, network management, power engineering, control engineering, Signal and Image Processing, Machine Learning, Control Systems and Applications, The book will offer the states of arts of tremendous advances in Wireless Networks and Information Systems and also serve as an excellent reference work for researchers and graduate students working on Wireless Networks and Information Systems.

  13. IMPROVED VIRTUAL CIRCUIT ROUTING ALGORITHM FOR WIRELESS SENSOR NETWORKS UNDER THE ASPECT OF POWER AWARENESS

    Directory of Open Access Journals (Sweden)

    Abid Ali Minhas

    2006-06-01

    Full Text Available Routing algorithms have shown their importance in the power aware wireless micro-sensor networks. In this paper first we present virtual circuit algorithm (VCRA, a routing algorithm for wireless sensor networks. We analyze the power utilized by nodes to lengthen the battery life and thus improving the lifetime of wireless sensor network. We discuss VCRA in comparison with the Multihoprouter, an algorithm developed by UC Berkeley. Then we present Improved Virtual Circuit Routing Algorithm (IVCRA which is an improved form of VCRA. In IVCRA node failure detection and path repairing scheme has been implemented. We also present the energy analysis of IVCRA and prove that IVCRA is the best choice. We first implement our routing algorithms in simulator TOSSIM and then on real hardware of mica2 mote-sensor network platform and prove the reliable routing of the data packets from different nodes to the base station. The motes used as nodes in our mote-sensor network are from Berkeley USA. By using simulator POWERTOSSIM, we estimate and present the energy utilized by different nodes of the network. At the end we present a comparison of our work with the network layer of Zigbee/IEEE 802.15.4, which is an emerging standard for wireless sensor networks and then compare its energy efficiency with the packet size chosen for our algorithm.

  14. A Wireless Sensor Network for Vineyard Monitoring That Uses Image Processing

    Science.gov (United States)

    Lloret, Jaime; Bosch, Ignacio; Sendra, Sandra; Serrano, Arturo

    2011-01-01

    The first step to detect when a vineyard has any type of deficiency, pest or disease is to observe its stems, its grapes and/or its leaves. To place a sensor in each leaf of every vineyard is obviously not feasible in terms of cost and deployment. We should thus look for new methods to detect these symptoms precisely and economically. In this paper, we present a wireless sensor network where each sensor node takes images from the field and internally uses image processing techniques to detect any unusual status in the leaves. This symptom could be caused by a deficiency, pest, disease or other harmful agent. When it is detected, the sensor node sends a message to a sink node through the wireless sensor network in order to notify the problem to the farmer. The wireless sensor uses the IEEE 802.11 a/b/g/n standard, which allows connections from large distances in open air. This paper describes the wireless sensor network design, the wireless sensor deployment, how the node processes the images in order to monitor the vineyard, and the sensor network traffic obtained from a test bed performed in a flat vineyard in Spain. Although the system is not able to distinguish between deficiency, pest, disease or other harmful agents, a symptoms image database and a neuronal network could be added in order learn from the experience and provide an accurate problem diagnosis. PMID:22163948

  15. Partial Interference and Its Performance Impact on Wireless Multiple Access Networks

    Directory of Open Access Journals (Sweden)

    Lau WingCheong

    2010-01-01

    Full Text Available To determine the capacity of wireless multiple access networks, the interference among the wireless links must be accurately modeled. In this paper, we formalize the notion of the partial interference phenomenon observed in many recent wireless measurement studies and establish analytical models with tractable solutions for various types of wireless multiple access networks. In particular, we characterize the stability region of IEEE 802.11 networks under partial interference with two potentially unsaturated links numerically. We also provide a closed-form solution for the stability region of slotted ALOHA networks under partial interference with two potentially unsaturated links and obtain a partial characterization of the boundary of the stability region for the general M-link case. Finally, we derive a closed-form approximated solution for the stability region for general M-link slotted ALOHA system under partial interference effects. Based on our results, we demonstrate that it is important to model the partial interference effects while analyzing wireless multiple access networks. This is because such considerations can result in not only significant quantitative differences in the predicted system capacity but also fundamental qualitative changes in the shape of the stability region of the systems.

  16. A wireless sensor network for vineyard monitoring that uses image processing.

    Science.gov (United States)

    Lloret, Jaime; Bosch, Ignacio; Sendra, Sandra; Serrano, Arturo

    2011-01-01

    The first step to detect when a vineyard has any type of deficiency, pest or disease is to observe its stems, its grapes and/or its leaves. To place a sensor in each leaf of every vineyard is obviously not feasible in terms of cost and deployment. We should thus look for new methods to detect these symptoms precisely and economically. In this paper, we present a wireless sensor network where each sensor node takes images from the field and internally uses image processing techniques to detect any unusual status in the leaves. This symptom could be caused by a deficiency, pest, disease or other harmful agent. When it is detected, the sensor node sends a message to a sink node through the wireless sensor network in order to notify the problem to the farmer. The wireless sensor uses the IEEE 802.11 a/b/g/n standard, which allows connections from large distances in open air. This paper describes the wireless sensor network design, the wireless sensor deployment, how the node processes the images in order to monitor the vineyard, and the sensor network traffic obtained from a test bed performed in a flat vineyard in Spain. Although the system is not able to distinguish between deficiency, pest, disease or other harmful agents, a symptoms image database and a neuronal network could be added in order learn from the experience and provide an accurate problem diagnosis.

  17. A Priority-Based Adaptive MAC Protocol for Wireless Body Area Networks

    Directory of Open Access Journals (Sweden)

    Sabin Bhandari

    2016-03-01

    Full Text Available In wireless body area networks (WBANs, various sensors and actuators are placed on/inside the human body and connected wirelessly. WBANs have specific requirements for healthcare and medical applications, hence, standard protocols like the IEEE 802.15.4 cannot fulfill all the requirements. Consequently, many medium access control (MAC protocols, mostly derived from the IEEE 802.15.4 superframe structure, have been studied. Nevertheless, they do not support a differentiated quality of service (QoS for the various forms of traffic coexisting in a WBAN. In particular, a QoS-aware MAC protocol is essential for WBANs operating in the unlicensed Industrial, Scientific, and Medical (ISM bands, because different wireless services like Bluetooth, WiFi, and Zigbee may coexist there and cause severe interference. In this paper, we propose a priority-based adaptive MAC (PA-MAC protocol for WBANs in unlicensed bands, which allocates time slots dynamically, based on the traffic priority. Further, multiple channels are effectively utilized to reduce access delays in a WBAN, in the presence of coexisting systems. Our performance evaluation results show that the proposed PA-MAC outperforms the IEEE 802.15.4 MAC and the conventional priority-based MAC in terms of the average transmission time, throughput, energy consumption, and data collision ratio.

  18. A Priority-Based Adaptive MAC Protocol for Wireless Body Area Networks.

    Science.gov (United States)

    Bhandari, Sabin; Moh, Sangman

    2016-03-18

    In wireless body area networks (WBANs), various sensors and actuators are placed on/inside the human body and connected wirelessly. WBANs have specific requirements for healthcare and medical applications, hence, standard protocols like the IEEE 802.15.4 cannot fulfill all the requirements. Consequently, many medium access control (MAC) protocols, mostly derived from the IEEE 802.15.4 superframe structure, have been studied. Nevertheless, they do not support a differentiated quality of service (QoS) for the various forms of traffic coexisting in a WBAN. In particular, a QoS-aware MAC protocol is essential for WBANs operating in the unlicensed Industrial, Scientific, and Medical (ISM) bands, because different wireless services like Bluetooth, WiFi, and Zigbee may coexist there and cause severe interference. In this paper, we propose a priority-based adaptive MAC (PA-MAC) protocol for WBANs in unlicensed bands, which allocates time slots dynamically, based on the traffic priority. Further, multiple channels are effectively utilized to reduce access delays in a WBAN, in the presence of coexisting systems. Our performance evaluation results show that the proposed PA-MAC outperforms the IEEE 802.15.4 MAC and the conventional priority-based MAC in terms of the average transmission time, throughput, energy consumption, and data collision ratio.

  19. Secure Wireless Sensor Networks: Problems and Solutions

    Directory of Open Access Journals (Sweden)

    Fei Hu

    2003-08-01

    Full Text Available As sensor networks edge closer towards wide-spread deployment, security issues become a central concern. So far, the main research focus has been on making sensor networks feasible and useful, and less emphasis was placed on security. This paper analyzes security challenges in wireless sensor networks and summarizes key issues that should be solved for achieving the ad hoc security. It gives an overview of the current state of solutions on such key issues as secure routing, prevention of denial-of-service and key management service. We also present some secure methods to achieve security in wireless sensor networks. Finally we present our integrated approach to securing sensor networks.

  20. Network coding at different layers in wireless networks

    CERN Document Server

    2016-01-01

    This book focuses on how to apply network coding at different layers in wireless networks – including MAC, routing, and TCP – with special focus on cognitive radio networks. It discusses how to select parameters in network coding (e.g., coding field, number of packets involved, and redundant information ration) in order to be suitable for the varying wireless environments. The book explores how to deploy network coding in MAC to improve network performance and examines joint network coding with opportunistic routing to improve the successful rate of routing. In regards to TCP and network coding, the text considers transport layer protocol working with network coding to overcome the transmission error rate, particularly with how to use the ACK feedback of TCP to enhance the efficiency of network coding. The book pertains to researchers and postgraduate students, especially whose interests are in opportunistic routing and TCP in cognitive radio networks.

  1. A Secure Key Establishment Protocol for ZigBee Wireless Sensor Networks

    DEFF Research Database (Denmark)

    Yuksel, Ender; Nielson, Hanne Riis; Nielson, Flemming

    2010-01-01

    ZigBee is a wireless sensor network standard that defines network and application layers on top of IEEE 802.15.4's physical and medium access control layers. In the latest version of ZigBee, enhancements are prescribed for the security sublayer but we show in this paper that problems persist....... In particular, we show that the end-to-end application key establishment protocol is flawed and we propose a secure protocol instead. We do so by using formal verification techniques based on static program analysis and process algebras. We present a way of using formal methods in wireless network security......, and propose a secure key establishment protocol for ZigBee networks....

  2. A Secure Key Establishment Protocol for ZigBee Wireless Sensor Networks

    DEFF Research Database (Denmark)

    Yuksel, Ender; Nielson, Hanne Riis; Nielson, Flemming

    2009-01-01

    ZigBee is a wireless sensor network standard that defines network and application layers on top of IEEE 802.15.4’s physical and medium access control layers. In the latest version of ZigBee, enhancements are prescribed for the security sublayer but we show in this paper that problems persist....... In particular we show that the End-to-End Application Key Establishment Protocol is flawed and we propose a secure protocol instead. We do so by using formal verification techniques based on static program analysis and process algebras. We present a way of using formal methods in wireless network security......, and propose a secure key establishment protocol for ZigBee networks....

  3. Location-Based Self-Adaptive Routing Algorithm for Wireless Sensor Networks in Home Automation

    Directory of Open Access Journals (Sweden)

    Hong SeungHo

    2011-01-01

    Full Text Available The use of wireless sensor networks in home automation (WSNHA is attractive due to their characteristics of self-organization, high sensing fidelity, low cost, and potential for rapid deployment. Although the AODVjr routing algorithm in IEEE 802.15.4/ZigBee and other routing algorithms have been designed for wireless sensor networks, not all are suitable for WSNHA. In this paper, we propose a location-based self-adaptive routing algorithm for WSNHA called WSNHA-LBAR. It confines route discovery flooding to a cylindrical request zone, which reduces the routing overhead and decreases broadcast storm problems in the MAC layer. It also automatically adjusts the size of the request zone using a self-adaptive algorithm based on Bayes' theorem. This makes WSNHA-LBAR more adaptable to the changes of the network state and easier to implement. Simulation results show improved network reliability as well as reduced routing overhead.

  4. Data centric wireless sensor networks

    NARCIS (Netherlands)

    Dulman, S.O.; Havinga, Paul J.M.

    2005-01-01

    The vision of wirteless sensing systems requires the development of devices and technologies that can be pervasive without being intrusive. The basic component of such a smart environment will be a small node with sensing and wireless communications capabilities, able to organize itself flexibly

  5. Design Optimization of Cyber-Physical Distributed Systems using IEEE Time-sensitive Networks (TSN)

    DEFF Research Database (Denmark)

    Pop, Paul; Lander Raagaard, Michael; Craciunas, Silviu S.

    2016-01-01

    to the optimization of distributed cyber-physical systems using real-time Ethernet for communication. Then, we formulate two novel optimization problems related to the scheduling and routing of TT and AVB traffic in TSN. Thus, we consider that we know the topology of the network as well as the set of TT and AVB flows......In this paper we are interested in safety-critical real-time applications implemented on distributed architectures supporting the Time-SensitiveNetworking (TSN) standard. The ongoing standardization of TSN is an IEEE effort to bring deterministic real-time capabilities into the IEEE 802.1 Ethernet...... standard supporting safety-critical systems and guaranteed Quality-of-Service. TSN will support Time-Triggered (TT) communication based on schedule tables, Audio-Video-Bridging (AVB) flows with bounded end-to-end latency as well as Best-Effort messages. We first present a survey of research related...

  6. A network architecture for precision formation flying using the IEEE 802.11 MAC Protocol

    Science.gov (United States)

    Clare, Loren P.; Gao, Jay L.; Jennings, Esther H.; Okino, Clayton

    2005-01-01

    Precision Formation Flying missions involve the tracking and maintenance of spacecraft in a desired geometric formation. The strong coupling of spacecraft in formation flying control requires inter-spacecraft communication to exchange information. In this paper, we present a network architecture that supports PFF control, from the initial random deployment phase to the final formation. We show that a suitable MAC layer for the application protocol is IEEE's 802.11 MAC protocol. IEEE 802.11 MAC has two modes of operations: DCF and PCF. We show that DCF is suitable for the initial deployment phase while switching to PCF when the spacecraft are in formation improves jitter and throughput. We also consider the effect of routing on protocol performance and suggest when it is profitable to turn off route discovery to achieve better network performance.

  7. Multi-Domain SDN Survivability for Agricultural Wireless Sensor Networks

    OpenAIRE

    Huang, Tao; Yan, Siyu; Yang, Fan; Liu, Jiang

    2016-01-01

    Wireless sensor networks (WSNs) have been widely applied in agriculture field; meanwhile, the advent of multi-domain software-defined networks (SDNs) have improved the wireless resource utilization rate and strengthened network management. In recent times, multi-domain SDNs have been applied to agricultural sensor networks, namely multi-domain software-defined wireless sensor networks (SDWSNs). However, when the SDNs controlling agriculture networks suddenly become unavailable, whether intra-...

  8. Synchronized Data Aggregation for Wireless Sensor Network

    DEFF Research Database (Denmark)

    Dnyaneshwar, Mantri; Prasad, Neeli R.; Prasad, Ramjee

    2014-01-01

    Wireless Sensor Networks (WSNs) are used for monitoring and data collection purposes. A key challenge in effective data collection is to schedule and synchronize the activities of the nodes with global clock. This paper proposes the Synchronized Data Aggregation Algorithm (SDA) using spanning tree...... mechanism. It provides network-wide time synchronization for sensor network. In the initial stage algorithm established the hierarchical structure in the network and then perform the pair - wise synchronization. SDA aggregate data with a global time scale throughout the network. The aggregated packets...

  9. Ad hoc mobile wireless networks principles, protocols and applications

    CERN Document Server

    Sarkar, Subir Kumar; Puttamadappa, C

    2007-01-01

    Ad hoc mobile wireless networks have seen increased adaptation in a variety of disciplines because they can be deployed with simple infrastructures and virtually no central administration. In particular, the development of ad hoc wireless and sensor networks provides tremendous opportunities in areas including disaster recovery, defense, health care, and industrial environments. Ad Hoc Mobile Wireless Networks: Principles, Protocols and Applications explains the concepts, mechanisms, design, and performance of these systems. It presents in-depth explanations of the latest wireless technologies

  10. Analysis of Radio communication solutions in small and isolated communities under the IEEE 802.22 standard

    OpenAIRE

    Arroyo Arzubi, Alejandro; Castro Lechtaler, Antonio; Foti, Antonio Roberto; Fusario, Rubén J.; García Guibout, Jorge; Sens, Lorena

    2013-01-01

    In recent years the use of wireless communications has increased significantly. Rural communities without cable network communication have found a solution in wireless technologies. Based on previous fieldwork, this paper analyzes software development of integration based technologies for communication equipment. It focuses on the feasibility of the IEEE 802.22 standard as a solution to the wireless problem.

  11. Wireless Local Area Network (WLAN) Vulnerability Assessment and Security

    National Research Council Canada - National Science Library

    Kessel, Adam; Goodwin, Shane

    2005-01-01

    The proliferation of wireless computer equipment and Local Area Networks (LANs) create an increasingly common and growing threat to Marine Corps Network infrastructure and communication security (COMSEC...

  12. Dimensioning Method for Conversational Video Applications in Wireless Convergent Networks

    Directory of Open Access Journals (Sweden)

    Raquel Perez Leal

    2007-12-01

    Full Text Available New convergent services are becoming possible, thanks to the expansion of IP networks based on the availability of innovative advanced coding formats such as H.264, which reduce network bandwidth requirements providing good video quality, and the rapid growth in the supply of dual-mode WiFi cellular terminals. This paper provides, first, a comprehensive subject overview as several technologies are involved, such as medium access protocol in IEEE802.11, H.264 advanced video coding standards, and conversational application characterization and recommendations. Second, the paper presents a new and simple dimensioning model of conversational video over wireless LAN. WLAN is addressed under the optimal network throughput and the perspective of video quality. The maximum number of simultaneous users resulting from throughput is limited by the collisions taking place in the shared medium with the statistical contention protocol. The video quality is conditioned by the packet loss in the contention protocol. Both approaches are analyzed within the scope of the advanced video codecs used in conversational video over IP, to conclude that conversational video dimensioning based on network throughput is not enough to ensure a satisfactory user experience, and video quality has to be taken also into account. Finally, the proposed model has been applied to a real-office scenario.

  13. How to secure a wireless sensor network

    NARCIS (Netherlands)

    Law, Y.W.; Havinga, Paul J.M.

    2005-01-01

    The security of wireless sensor networks (WSNs) is a complex issue. While security research of WSNs is progressing at a tremendous pace, and many security techniques have been proposed, no comprehensive framework has so far emerged that attempts to tie the bits and pieces together to ease the

  14. Load balancing in integrated optical wireless networks

    DEFF Research Database (Denmark)

    Yan, Ying; Dittmann, Lars; Wong, S-W.

    2010-01-01

    In this paper, we tackle the load balancing problem in Integrated Optical Wireless Networks, where cell breathing technique is used to solve congestion by changing the coverage area of a fully loaded cell tower. Our objective is to design a load balancing mechanism which works closely with the in...

  15. Clock Synchronization for Multihop Wireless Sensor Networks

    Science.gov (United States)

    Solis Robles, Roberto

    2009-01-01

    In wireless sensor networks, more so generally than in other types of distributed systems, clock synchronization is crucial since by having this service available, several applications such as media access protocols, object tracking, or data fusion, would improve their performance. In this dissertation, we propose a set of algorithms to achieve…

  16. Censored cooperative positioning for dense wireless networks

    NARCIS (Netherlands)

    Das, Kallol; Wymeersch, Henk

    Cooperative positioning is an emerging topic in wireless sensor networks and navigation. It can improve the positioning accuracy and coverage in GPS-challenged conditions such as inside tunnels, in urban canyons, and indoors. Different algorithms have been proposed relying on iteratively exchanging

  17. Benchmarking Block Ciphers for Wireless Sensor Networks

    NARCIS (Netherlands)

    Law, Y.W.; Doumen, J.M.; Hartel, Pieter H.

    2004-01-01

    Choosing the most storage- and energy-efficient block cipher specifically for wireless sensor networks (WSNs) is not as straightforward as it seems. To our knowledge so far, there is no systematic evaluation framework for the purpose. We have identified the candidates of block ciphers suitable for

  18. Problem solving for wireless sensor networks

    CERN Document Server

    Garcia-Hernando, Ana-Belen; Lopez-Navarro, Juan-Manuel; Prayati, Aggeliki; Redondo-Lopez, Luis

    2008-01-01

    Wireless Sensor Networks (WSN) is an area of huge research interest, attracting substantial attention from industry and academia for its enormous potential and its inherent challenges. This reader-friendly text delivers a comprehensive review of the developments related to the important technological issues in WSN.

  19. Challenge: How Effective is Routing for Wireless Networking

    Science.gov (United States)

    2017-03-03

    variations of the envi- ronment or atmosphere will induce a “transition region” in which the probability of packet error increases from 0 to 1. For...Taoka et al., “Scenarios for 5g mobile and wireless communications: the vision of the metis project,” Communications Magazine , IEEE, vol. 52, no. 5

  20. Cooperative Data Management in Wireless Sensor Networks

    Directory of Open Access Journals (Sweden)

    Hajar Mousannif

    2012-06-01

    Full Text Available Introducing cooperation into a wireless sensor network (WSN has gained much attention in the recent few years mainly because of the significant effect it has on optimizing energy consumption and on enhancing the lifetime and the overall performance of the network. Cooperation can be exploited at different levels, ranging from a collection of nodes collaborating to forward the data they gathered from the environment towards the base station through efficient data aggregation and clustering techniques, to nodes collaborating to report events occurrences, track targets or control the topology. Motivated by a large variety of attractive wireless sensor applications, such as environmental monitoring, smart environments and healthcare applications, we survey mechanisms that take advantage of cooperation among sensor nodes in the network for the purpose of delivering information reliably and efficiently to nodes of the network that are interested in receiving it. We provide detailed overviews and highlight the importance of cooperation from different perspectives.

  1. A Reinforcement Sensor Embedded Vertical Handoff Controller for Vehicular Heterogeneous Wireless Networks

    Directory of Open Access Journals (Sweden)

    Lin Ma

    2013-11-01

    Full Text Available Vehicular communication platforms that provide real-time access to wireless networks have drawn more and more attention in recent years. IEEE 802.11p is the main radio access technology that supports communication for high mobility terminals, however, due to its limited coverage, IEEE 802.11p is usually deployed by coupling with cellular networks to achieve seamless mobility. In a heterogeneous cellular/802.11p network, vehicular communication is characterized by its short time span in association with a wireless local area network (WLAN. Moreover, for the media access control (MAC scheme used for WLAN, the network throughput dramatically decreases with increasing user quantity. In response to these compelling problems, we propose a reinforcement sensor (RFS embedded vertical handoff control strategy to support mobility management. The RFS has online learning capability and can provide optimal handoff decisions in an adaptive fashion without prior knowledge. The algorithm integrates considerations including vehicular mobility, traffic load, handoff latency, and network status. Simulation results verify that the proposed algorithm can adaptively adjust the handoff strategy, allowing users to stay connected to the best network. Furthermore, the algorithm can ensure that RSUs are adequate, thereby guaranteeing a high quality user experience.

  2. Data storage system for wireless sensor networks

    OpenAIRE

    Sacramento, David

    2015-01-01

    Dissertação de mestrado, Engenharia Informática, Faculdade de Ciências e Tecnologia, Universidade do Algarve, 2015 Wireless sensor networks (WSNs) are starting to have a high impact on our societies and, for next generation WSNs to become more integrated with the Internet, researchers recently proposed to embed Internet Protocol (IP) v6 into such very constrained networks. Also, Constrained Application Protocol (CoAP) and Observe have been proposed for RESTful services to be pr...

  3. Advanced routing protocols for wireless networks

    CERN Document Server

    Campista , Miguel Elias Mitre

    2014-01-01

    This text introduces the principles of routing protocols and metrics as they affect wireless networking environments, specifically in urban areas. Timely because of the recent rise in small city life, this topic includes the consideration of ad hoc, mesh, vehicular, sensor, and delay tolerant networks. These approaches are each unique, and author Miguel Mitre Campista provides a thorough, but accessible, explanation of their individual characteristics for engineers, computer scientists, IT professionals, and curious Internet users.

  4. A tutorial survey of topics in wireless networking

    Indian Academy of Sciences (India)

    In the second part of the paper, we first analyse random access wireless networks and pay special attention to 802·11 (Wi-Fi) networks. We then survey some topics in ad hoc multihop wireless networks, where we discuss arbitrary networks, as well as some theory of dense random networks. Finally, we provide an overview ...

  5. Adaptive QoS provision for IEEE 802.16e BWA networks based on cross-layer design

    Directory of Open Access Journals (Sweden)

    Kuo GS

    2011-01-01

    Full Text Available Abstract This article proposes an integrated framework for adaptive QoS provision in IEEE 802.16e broadband wireless access networks based on cross-layer design. On one hand, an efficient admission control (AC algorithm is proposed along with a semi-reservation scheme to guarantee the connection-level QoS. First, to guarantee the service continuity for handoff connections and resource efficiency, our semi-reservation scheme considers both users' handoff probability and average resource consumption together, which effectively avoids resource over-reservation and insufficient reservation. For AC, a new/handoff connection is accepted only when the target cell has enough resource to afford both instantaneous and average resource consumption to meet the average source rate request. On the other hand, a joint resource allocation and packet scheduling scheme is designed to provide packet-level QoS guarantee in term of "QoS rate", which can ensure fairness for the services with identical priority level in case of bandwidth shortage. Particularly, an enhanced bandwidth request scheme is designed to reduce unnecessary BR delay and redundant signaling overhead caused by the existing one in IEEE 802.16e, which further improves the packet-level QoS performance and resource efficiency for uplink transmission. Simulation results show that the proposed approach not only balances the tradeoff among connection blocking rate, connection dropping rate, and connection failure rate, but also achieves low mean packet dropping rate (PDR, small deviation of PDR, and low QoS outage rate. Moreover, high resource efficiency is ensured.

  6. Multi-Channel Distributed Coordinated Function over Single Radio in Wireless Sensor Networks

    Directory of Open Access Journals (Sweden)

    Kok-Keong (Jonathan Loo

    2011-01-01

    Full Text Available Multi-channel assignments are becoming the solution of choice to improve performance in single radio for wireless networks. Multi-channel allows wireless networks to assign different channels to different nodes in real-time transmission. In this paper, we propose a new approach, Multi-channel Distributed Coordinated Function (MC-DCF which takes advantage of multi-channel assignment. The backoff algorithm of the IEEE 802.11 distributed coordination function (DCF was modified to invoke channel switching, based on threshold criteria in order to improve the overall throughput for wireless sensor networks (WSNs over 802.11 networks. We presented simulation experiments in order to investigate the characteristics of multi-channel communication in wireless sensor networks using an NS2 platform. Nodes only use a single radio and perform channel switching only after specified threshold is reached. Single radio can only work on one channel at any given time. All nodes initiate constant bit rate streams towards the receiving nodes. In this work, we studied the impact of non-overlapping channels in the 2.4 frequency band on: constant bit rate (CBR streams, node density, source nodes sending data directly to sink and signal strength by varying distances between the sensor nodes and operating frequencies of the radios with different data rates. We showed that multi-channel enhancement using our proposed algorithm provides significant improvement in terms of throughput, packet delivery ratio and delay. This technique can be considered for WSNs future use in 802.11 networks especially when the IEEE 802.11n becomes popular thereby may prevent the 802.15.4 network from operating effectively in the 2.4 GHz frequency band.

  7. Multi-channel distributed coordinated function over single radio in wireless sensor networks.

    Science.gov (United States)

    Campbell, Carlene E-A; Loo, Kok-Keong Jonathan; Gemikonakli, Orhan; Khan, Shafiullah; Singh, Dhananjay

    2011-01-01

    Multi-channel assignments are becoming the solution of choice to improve performance in single radio for wireless networks. Multi-channel allows wireless networks to assign different channels to different nodes in real-time transmission. In this paper, we propose a new approach, Multi-channel Distributed Coordinated Function (MC-DCF) which takes advantage of multi-channel assignment. The backoff algorithm of the IEEE 802.11 distributed coordination function (DCF) was modified to invoke channel switching, based on threshold criteria in order to improve the overall throughput for wireless sensor networks (WSNs) over 802.11 networks. We presented simulation experiments in order to investigate the characteristics of multi-channel communication in wireless sensor networks using an NS2 platform. Nodes only use a single radio and perform channel switching only after specified threshold is reached. Single radio can only work on one channel at any given time. All nodes initiate constant bit rate streams towards the receiving nodes. In this work, we studied the impact of non-overlapping channels in the 2.4 frequency band on: constant bit rate (CBR) streams, node density, source nodes sending data directly to sink and signal strength by varying distances between the sensor nodes and operating frequencies of the radios with different data rates. We showed that multi-channel enhancement using our proposed algorithm provides significant improvement in terms of throughput, packet delivery ratio and delay. This technique can be considered for WSNs future use in 802.11 networks especially when the IEEE 802.11n becomes popular thereby may prevent the 802.15.4 network from operating effectively in the 2.4 GHz frequency band.

  8. Distributed Estimation, Coding, and Scheduling in Wireless Visual Sensor Networks

    Science.gov (United States)

    Yu, Chao

    2013-01-01

    In this thesis, we consider estimation, coding, and sensor scheduling for energy efficient operation of wireless visual sensor networks (VSN), which consist of battery-powered wireless sensors with sensing (imaging), computation, and communication capabilities. The competing requirements for applications of these wireless sensor networks (WSN)…

  9. Cooperative networking in a heterogeneous wireless medium

    CERN Document Server

    Ismail, Muhammad

    2013-01-01

    This brief focuses on radio resource allocation in a heterogeneous wireless medium. It presents radio resource allocation algorithms with decentralized implementation, which support both single-network and multi-homing services. The brief provides a set of cooperative networking algorithms, which rely on the concepts of short-term call traffic load prediction, network cooperation, convex optimization, and decomposition theory. In the proposed solutions, mobile terminals play an active role in the resource allocation operation, instead of their traditional role as passive service recipients in the networking environment.

  10. An underwater optical wireless communication network

    Science.gov (United States)

    Arnon, Shlomi

    2009-08-01

    The growing need for underwater observation and sub-sea monitoring systems has stimulated considerable interest in advancing the enabling technologies of underwater wireless communication and underwater sensor networks. This communication technology is expected to play an important role in investigating climate change, in monitoring biological, bio-geochemical, evolutionary and ecological changes in the sea, ocean and lake environments and in helping to control and maintain oil production facilities and harbors using unmanned underwater vehicles (UUVs), submarines, ships, buoys, and divers. However, the present technology of underwater acoustic communication cannot provide the high data rate required to investigate and monitor these environments and facilities. Optical wireless communication has been proposed as the best alternative to meet this challenge. We present models of three kinds of optical wireless communication links a) a line-of-sight link, b) a modulating retro-reflector link and c) a reflective link, all of which can provide the required data rate. We analyze the link performance based on these models. From the analysis, it is clear that as the water absorption increases, the communication performance decreases dramatically for the three link types. However, by using the scattered lighted it was possible to mitigate this decrease in some cases. We conclude from the analysis that a high data rate underwater optical wireless network is a feasible solution for emerging applications such as UUV to UUV links and networks of sensors, and extended ranges in these applications could be achieved by applying a multi-hop concept.

  11. Wireless sensor networks principles, design and applications

    CERN Document Server

    Yang, Shuang-Hua

    2014-01-01

    Wireless Sensor Networks presents the latest practical solutions to the design issues presented in wireless-sensor-network-based systems. Novel features of the text, distributed throughout, include workable solutions, demonstration systems and case studies of the design and application of wireless sensor networks (WSNs) based on the first-hand research and development experience of the author, and the chapters on real applications: building fire safety protection; smart home automation; and logistics resource management. Case studies and applications illustrate the practical perspectives of: ·         sensor node design; ·         embedded software design; ·         routing algorithms; ·         sink node positioning; ·         co-existence with other wireless systems; ·         data fusion; ·         security; ·         indoor location tracking; ·         integrating with radio-frequency identification; and ·         In...

  12. Self-Coexistence among IEEE 802.22 Networks: Distributed Allocation of Power and Channel.

    Science.gov (United States)

    Sakin, Sayef Azad; Razzaque, Md Abdur; Hassan, Mohammad Mehedi; Alamri, Atif; Tran, Nguyen H; Fortino, Giancarlo

    2017-12-07

    Ensuring self-coexistence among IEEE 802.22 networks is a challenging problem owing to opportunistic access of incumbent-free radio resources by users in co-located networks. In this study, we propose a fully-distributed non-cooperative approach to ensure self-coexistence in downlink channels of IEEE 802.22 networks. We formulate the self-coexistence problem as a mixed-integer non-linear optimization problem for maximizing the network data rate, which is an NP-hard one. This work explores a sub-optimal solution by dividing the optimization problem into downlink channel allocation and power assignment sub-problems. Considering fairness, quality of service and minimum interference for customer-premises-equipment, we also develop a greedy algorithm for channel allocation and a non-cooperative game-theoretic framework for near-optimal power allocation. The base stations of networks are treated as players in a game, where they try to increase spectrum utilization by controlling power and reaching a Nash equilibrium point. We further develop a utility function for the game to increase the data rate by minimizing the transmission power and, subsequently, the interference from neighboring networks. A theoretical proof of the uniqueness and existence of the Nash equilibrium has been presented. Performance improvements in terms of data-rate with a degree of fairness compared to a cooperative branch-and-bound-based algorithm and a non-cooperative greedy approach have been shown through simulation studies.

  13. Self-Coexistence among IEEE 802.22 Networks: Distributed Allocation of Power and Channel

    Directory of Open Access Journals (Sweden)

    Sayef Azad Sakin

    2017-12-01

    Full Text Available Ensuring self-coexistence among IEEE 802.22 networks is a challenging problem owing to opportunistic access of incumbent-free radio resources by users in co-located networks. In this study, we propose a fully-distributed non-cooperative approach to ensure self-coexistence in downlink channels of IEEE 802.22 networks. We formulate the self-coexistence problem as a mixed-integer non-linear optimization problem for maximizing the network data rate, which is an NP-hard one. This work explores a sub-optimal solution by dividing the optimization problem into downlink channel allocation and power assignment sub-problems. Considering fairness, quality of service and minimum interference for customer-premises-equipment, we also develop a greedy algorithm for channel allocation and a non-cooperative game-theoretic framework for near-optimal power allocation. The base stations of networks are treated as players in a game, where they try to increase spectrum utilization by controlling power and reaching a Nash equilibrium point. We further develop a utility function for the game to increase the data rate by minimizing the transmission power and, subsequently, the interference from neighboring networks. A theoretical proof of the uniqueness and existence of the Nash equilibrium has been presented. Performance improvements in terms of data-rate with a degree of fairness compared to a cooperative branch-and-bound-based algorithm and a non-cooperative greedy approach have been shown through simulation studies.

  14. A novel beamforming based model of coverage and transmission costing in IEEE 802.11 WLAN networks

    Directory of Open Access Journals (Sweden)

    Mehdi Guessous

    2017-09-01

    Full Text Available IEEE 802.11 WLAN indoor networks face major inherent and environmental issues such as interference, noise, and obstacles. At the same time, they must provide a maximal service performance in highly changing radio environments and conformance to various applications’ requirements. For this purpose, they require a solid design approach that considers both inputs from the radio interface and the upper-layer services at every design step. The modelization of radio area coverage is a key component in this process and must build on feasible work hypotheses. It should be able also to interpret highly varying characteristics of dense indoor environments, technology advances, service design best practices, end-to-end integration with other network parts: Local Area Network (LAN, Wide Area Network (WAN or Data Center Network (DCN. This work focuses on Radio Resource Management (RRM as a key tool to achieve a solid design in WLAN indoor environments by planning frequency channel assignment, transmit directions and corresponding power levels. Its scope is limited to tackle co-channel interference but can be easily extended to address cross-channel ones. In this paper, we consider beamforming and costing techniques to augment conventional RRM’s Transmit Power Control (TPC procedures that market-leading vendors has implemented and related research has worked on. We present a novel approach of radio coverage modelization and prove its additions to the cited related-work’s models. Our solution model runs three algorithms to evaluate transmission opportunities of Wireless Devices (WD under the coverage area. It builds on realistic hypotheses and a thorough system operation’s understanding to evaluate such an opportunity to transmit, overcomes limitations from compared related-work’s models, and integrates a hierarchical costing system to match Service Level Agreement (SLA expectations. The term “opportunity” in this context relates also to the new

  15. An Overview on Wireless Sensor Networks Technology and Evolution

    Directory of Open Access Journals (Sweden)

    Chiara Buratti

    2009-08-01

    Full Text Available Wireless sensor networks (WSNs enable new applications and require non-conventional paradigms for protocol design due to several constraints. Owing to the requirement for low device complexity together with low energy consumption (i.e., long network lifetime, a proper balance between communication and signal/data processing capabilities must be found. This motivates a huge effort in research activities, standardization process, and industrial investments on this field since the last decade. This survey paper aims at reporting an overview of WSNs technologies, main applications and standards, features in WSNs design, and evolutions. In particular, some peculiar applications, such as those based on environmental monitoring, are discussed and design strategies highlighted; a case study based on a real implementation is also reported. Trends and possible evolutions are traced. Emphasis is given to the IEEE 802.15.4 technology, which enables many applications of WSNs. Some example of performance characteristics of 802.15.4-based networks are shown and discussed as a function of the size of the WSN and the data type to be exchanged among nodes.

  16. Sensor Network in the Wireless UHF Band

    Science.gov (United States)

    Mariño, P.; Fontán, F. P.; Domínguez, M. A.; Otero, S.

    Biological research in agriculture needs a lot of specialized electronic sensors in order to fulfill different goals, like as: climate monitoring, soil and fruit assessment, control of insects and diseases, chemical pollutants, identification and control of weeds, crop tracking, and so on. That research must be supported by consistent biological models able to simulate diverse environmental conditions, in order to predict the right human actions before risky biological damage could be irreversible. In this paper an experimental distributed network based on climatic and biological wireless sensors is described, for providing real measurements in order to validate different biological models used for viticulture applications. Firstly the experimental network for field automatic data acquisition is presented, as a system based in a distributed process. Then, the design of the wireless network is explained in detail, with a previous discussion about the state-of-the-art, and some measurements for viticulture research are pointed out. Finally future developments and conclusions are stated.

  17. TMAC: Timestamp-Ordered MAC Protocol for Wireless Mesh Networks

    KAUST Repository

    Nawab, Faisal

    2011-05-01

    Wireless Mesh Networks (WMNs) have emerged to meet a need for a self-organized and self-configured multi-hop wireless network infrastructure. Low cost infrastructure and ease of deployment have made WMNs an attractive technology for last mile access. However, 802.11 based WMNs are subject to serious fairness issues. With backlogged TCP traffic, nodes which are two or more hops away from the gateway are subject to starvation, while the one-hop away node saturates the channel with its own local traffic. We study the interactions of TCP and IEEE 802.11 MAC in WMNs to aid us in understanding and overcoming the unfairness problem. We propose a Markov chain to capture the behavior of TCP sessions, particularly the impact on network throughput performance due to the effect of queue utilization and packet relaying. A closed form solution is derived to numerically derive the throughput. Based on the developed model, we propose a distributed MAC protocol called Timestamp-ordered MAC (TMAC), aiming to alleviate the unfairness problem in WMNs via a manipulative per-node scheduling mechanism which takes advantage of the age of each packet as a priority metric. Simulation is conducted to validate our model and to illustrate the fairness characteristics of TMAC. Our results show that TMAC achieves excellent resource allocation fairness while maintaining above 90% of maximum link capacity in parking lot and large grid topologies. Our work illuminates the factors affecting TCP fairness in WMNs. Our theoretical and empirical findings can be used in future research to develop more fairness-aware protocols for WMNs.

  18. Priority image transmission in wireless sensor networks

    International Nuclear Information System (INIS)

    Nasri, M.; Helali, A.; Sghaier, H.; Maaref, H.

    2011-01-01

    The emerging technology during the last years allowed the development of new sensors equipped with wireless communication which can be organized into a cooperative autonomous network. Some application areas for wireless sensor networks (WSNs) are home automations, health care services, military domain, and environment monitoring. The required constraints are limited capacity of processing, limited storage capability, and especially these nodes are limited in energy. In addition, such networks are tiny battery powered which their lifetime is very limited. During image processing and transmission to the destination, the lifetime of sensor network is decreased quickly due to battery and processing power constraints. Therefore, digital image transmissions are a significant challenge for image sensor based Wireless Sensor Networks (WSNs). Based on a wavelet image compression, we propose a novel, robust and energy-efficient scheme, called Priority Image Transmission (PIT) in WSN by providing various priority levels during image transmissions. Different priorities in the compressed image are considered. The information for the significant wavelet coeffcients are transmitted with higher quality assurance, whereas relatively less important coefficients are transmitted with lower overhead. Simulation results show that the proposed scheme prolongs the system lifetime and achieves higher energy efficiency in WSN with an acceptable compromise on the image quality.

  19. Passive intrusion detection in wireless networks by exploiting clustering-based learning

    Science.gov (United States)

    Yang, Jie; Chen, Yingying; Desai, Sachi; Quoraishee, Shafik

    2010-04-01

    The large-scale wireless sensing data collected from wireless networks can be used for detecting intruders (e.g., enemies in tactical fields), and further facilitating real-time situation awareness in Army's networkcentric warfare applications such as intrusion detection, battlefield protection and emergency evacuation. In this work, we focus on exploiting Received Signal Strength (RSS) obtained from the existing wireless infrastructures for performing intrusion detection when the intruders or objects do not carry any radio devices. This is also known as passive intrusion detection. Passive intrusion detection based on the RSS data is an attractive approach as it reuses the existing wireless environmental data without requiring a specialized infrastructure. We propose a clustering-based learning mechanism for passive intrusion detection in wireless networks. Specifically, our detection scheme utilizes the clustering method to analyze the changes of RSS, caused by intrusions, at multiple devices to diagnose the presence of intrusions collaboratively. Our experimental results using an IEEE 802.15.4 (Zigbee) network in a real office environment show that our clustering-based learning can effectively detect the presence of intrusions.

  20. A Novel Situation Specific Network Security for Wireless Sensor Networks

    Directory of Open Access Journals (Sweden)

    Mohammad Al-Rousan

    2015-03-01

    Full Text Available Researchers have come up with many high level security protocols and key management algorithms that can be applied for different types of networks. The main characteristics of wireless sensor networks that are limited computation and power made it difficult to apply these secure key management algorithms since it consumes much power and resources. Sensors in the field at different periods of time of their life time need higher level of security more than other times - sensors in a battlefield need higher security when it is war time. In our research we developed an adaptive security protocol for two-layer clustered heterogeneous wireless sensor networks that can toggle between five different modes of operation, each with different security level. Each level of security has its own encryption/decryption algorithm and specified key length depending on the situation of the application and the situation for the wireless sensor networks.

  1. A Formal Evaluation of the Security Schemes for Wireless Networks

    OpenAIRE

    Shadi R. Masadeh; Nidal Turab

    2011-01-01

    Information security is a critical issue in the wireless network, because the transmission media is open (no physical control on the air). Any wireless device equipped with wireless interface can use and share the airwave transmission medium with other users. For protection purposes, several security mechanisms have been developed over years. This paper provides systematic evaluation of different security schemes used in wireless networks: WEP, TKIP, WPA, AES and WPA2. A formal comparison is ...

  2. Analyzing Multimode Wireless Sensor Networks Using the Network Calculus

    Directory of Open Access Journals (Sweden)

    Xi Jin

    2015-01-01

    Full Text Available The network calculus is a powerful tool to analyze the performance of wireless sensor networks. But the original network calculus can only model the single-mode wireless sensor network. In this paper, we combine the original network calculus with the multimode model to analyze the maximum delay bound of the flow of interest in the multimode wireless sensor network. There are two combined methods A-MM and N-MM. The method A-MM models the whole network as a multimode component, and the method N-MM models each node as a multimode component. We prove that the maximum delay bound computed by the method A-MM is tighter than or equal to that computed by the method N-MM. Experiments show that our proposed methods can significantly decrease the analytical delay bound comparing with the separate flow analysis method. For the large-scale wireless sensor network with 32 thousands of sensor nodes, our proposed methods can decrease about 70% of the analytical delay bound.

  3. An Adaptive Allocation Algorithm Using Directional CSMA/CA over mmWave Wireless Personal Area Networks

    Directory of Open Access Journals (Sweden)

    Hyunhee Park

    2012-04-01

    Full Text Available Directional antennas have the considerable benefits of higher antenna gain, long transmission distance and spatial reuse compared to omni-antennas. To support a directional antenna, IEEE 802.15.3c specifies a high data transmission rate and short frequency range communication based on the characteristics of 60GHz band. However, the contention-based protocol of IEEE 802.15.3c may cause channel collisions and throughput degradation as the number of stations in the network increases. In order to resolve this problem and reduce channel access latency, we propose an adaptive allocation algorithm in which the contention window size for optimal transmission probability is derived after the directional information has been obtained by means of AP control procedures. Extensive simulations demonstrate that the proposed algorithm outperforms the existing channel access scheme in IEEE 802.15.3c wireless personal area networks under different situations, especially when the number of contending stations is large.

  4. The use of Wireless Sensor Network for increasing airport security

    Directory of Open Access Journals (Sweden)

    Jakub Kraus

    2013-11-01

    Full Text Available This article focuses on the use of wireless sensor networks for airport security, respectively using sensor networks as a replacement or add-on to existing security measures. The article describes the sensor network and its possible application to various airport objects and financial analysis of the perimeter security with wireless sensor network.

  5. Scalable Video Streaming in Wireless Mesh Networks for Education

    Science.gov (United States)

    Liu, Yan; Wang, Xinheng; Zhao, Liqiang

    2011-01-01

    In this paper, a video streaming system for education based on a wireless mesh network is proposed. A wireless mesh network is a self-organizing, self-managing and reliable intelligent network, which allows educators to deploy a network quickly. Video streaming plays an important role in this system for multimedia data transmission. This new…

  6. Wireless sensor networks distributed consensus estimation

    CERN Document Server

    Chen, Cailian; Guan, Xinping

    2014-01-01

    This SpringerBrief evaluates the cooperative effort of sensor nodes to accomplish high-level tasks with sensing, data processing and communication. The metrics of network-wide convergence, unbiasedness, consistency and optimality are discussed through network topology, distributed estimation algorithms and consensus strategy. Systematic analysis reveals that proper deployment of sensor nodes and a small number of low-cost relays (without sensing function) can speed up the information fusion and thus improve the estimation capability of wireless sensor networks (WSNs). This brief also investiga

  7. Security for multi-hop wireless networks

    CERN Document Server

    Mahmoud, Mohamed M E A

    2014-01-01

    This Springer Brief discusses efficient security protocols and schemes for multi-hop wireless networks. It presents an overview of security requirements for these networks, explores challenges in securing networks and presents system models. The authors introduce mechanisms to reduce the overhead and identify malicious nodes that drop packets intentionally. Also included is a new, efficient cooperation incentive scheme to stimulate the selfish nodes to relay information packets and enforce fairness. Many examples are provided, along with predictions for future directions of the field. Security

  8. Key Management in Wireless Sensor Networks

    Directory of Open Access Journals (Sweden)

    Ismail Mansour

    2015-09-01

    Full Text Available Wireless sensor networks are a challenging field of research when it comes to security issues. Using low cost sensor nodes with limited resources makes it difficult for cryptographic algorithms to function without impacting energy consumption and latency. In this paper, we focus on key management issues in multi-hop wireless sensor networks. These networks are easy to attack due to the open nature of the wireless medium. Intruders could try to penetrate the network, capture nodes or take control over particular nodes. In this context, it is important to revoke and renew keys that might be learned by malicious nodes. We propose several secure protocols for key revocation and key renewal based on symmetric encryption and elliptic curve cryptography. All protocols are secure, but have different security levels. Each proposed protocol is formally proven and analyzed using Scyther, an automatic verification tool for cryptographic protocols. For efficiency comparison sake, we implemented all protocols on real testbeds using TelosB motes and discussed their performances.

  9. Segmentized Clear Channel Assessment for IEEE 802.15.4 Networks

    Directory of Open Access Journals (Sweden)

    Kyou Jung Son

    2016-06-01

    Full Text Available This paper proposed segmentized clear channel assessment (CCA which increases the performance of IEEE 802.15.4 networks by improving carrier sense multiple access with collision avoidance (CSMA/CA. Improving CSMA/CA is important because the low-power consumption feature and throughput performance of IEEE 802.15.4 are greatly affected by CSMA/CA behavior. To improve the performance of CSMA/CA, this paper focused on increasing the chance to transmit a packet by assessing precise channel status. The previous method used in CCA, which is employed by CSMA/CA, assesses the channel by measuring the energy level of the channel. However, this method shows limited channel assessing behavior, which comes from simple threshold dependent channel busy evaluation. The proposed method solves this limited channel decision problem by dividing CCA into two groups. Two groups of CCA compare their energy levels to get precise channel status. To evaluate the performance of the segmentized CCA method, a Markov chain model has been developed. The validation of analytic results is confirmed by comparing them with simulation results. Additionally, simulation results show the proposed method is improving a maximum 8.76% of throughput and decreasing a maximum 3.9% of the average number of CCAs per packet transmission than the IEEE 802.15.4 CCA method.

  10. Segmentized Clear Channel Assessment for IEEE 802.15.4 Networks.

    Science.gov (United States)

    Son, Kyou Jung; Hong, Sung Hyeuck; Moon, Seong-Pil; Chang, Tae Gyu; Cho, Hanjin

    2016-06-03

    This paper proposed segmentized clear channel assessment (CCA) which increases the performance of IEEE 802.15.4 networks by improving carrier sense multiple access with collision avoidance (CSMA/CA). Improving CSMA/CA is important because the low-power consumption feature and throughput performance of IEEE 802.15.4 are greatly affected by CSMA/CA behavior. To improve the performance of CSMA/CA, this paper focused on increasing the chance to transmit a packet by assessing precise channel status. The previous method used in CCA, which is employed by CSMA/CA, assesses the channel by measuring the energy level of the channel. However, this method shows limited channel assessing behavior, which comes from simple threshold dependent channel busy evaluation. The proposed method solves this limited channel decision problem by dividing CCA into two groups. Two groups of CCA compare their energy levels to get precise channel status. To evaluate the performance of the segmentized CCA method, a Markov chain model has been developed. The validation of analytic results is confirmed by comparing them with simulation results. Additionally, simulation results show the proposed method is improving a maximum 8.76% of throughput and decreasing a maximum 3.9% of the average number of CCAs per packet transmission than the IEEE 802.15.4 CCA method.

  11. Using Forced Handover as Load Balancing Technique in IEEE 802.16e/WiMAX Networks to Ensure QoS Guarantees

    Directory of Open Access Journals (Sweden)

    Abdul Qadir Ansari

    2011-04-01

    Full Text Available Wireless networks perform handover to enable MS (Mobile Stations to move from one BS (Base Station to other BS during a session and without hiccups. Handovers are performed for many reasons such as, MS movement, varying radio conditions and capacity offloading to achieve negotiated service quality. Network congestion is generally observed at popular business places (like downtowns and during busy hours, when load on network increases sporadically. We propose forced handover, as a load balancing technique to handle such congestion in IEEE 802.16e networks. Existing approaches like adding more channels, forming sectors, increasing channel duration and using relay stations etc. to overcome congestion are not cost effective solutions, in situations when there is episodic increase in network load; moreover such techniques are always encumbered by the modifications that involve both licensing and cost. Our strategy to cater situations of periodic congestion is to enforce BS initiated handover of MSs at cell boundaries, observing acceptable SNR (Signal to Noise Ratio from one of the neighboring BSs with enough capacity and thereby freeing resources for MSs that cannot be switched from one cell to another (observing high SNR for being near to BS. The proposed mechanism is tested using OPNET environment using Wireless Modeler. Performance analysis validates the proposed strategy and its effectiveness to overcome such sporadic congestion is confirmed through observable improvement in traffic statistics.

  12. Wireless data over RAM's Mobitex network

    Science.gov (United States)

    Khan, M. Mobeen

    1995-12-01

    Mobitex is a mobile data technology standard created by Eritel, now a wholly owned subsidiary of Ericsson, that has been in existence for about a decade. Originally designed as a low speed (1.2 kbps) data system with a voice dispatch overlay, it was significantly enhanced in 1990 for use in North America and the UK. The enhanced system is a data-only system using cellular architecture and multi-channel frequency reuse, store-and-forward capability, and an 8 kbps over-the-air data rate. The mission of RAM Mobile Data USA Limited Partnership ('RAM') is to provide high quality, cost efficient, wireless data communications solutions in its targeted market segments. RAM's Mobitex network is currently one of the two networks providing two way wireless data services nationwide using a long distance service provider of the customer's choice.

  13. QoE management in wireless networks

    CERN Document Server

    Wang, Ying; Zhang, Ping

    2017-01-01

    This SpringerBrief presents research results on QoE management schemes for mobile services, including user services, and resource allocation. Along with a review of the research literature, it offers a data-driven architecture for personalized QoE management in wireless networks. The primary focus is on introducing efficient personalized character extraction mechanisms, e.g., context-aware Bayesian graph model, and cooperative QoE management mechanisms. Moreover, in order to demonstrate in the effectiveness of the QoE model, a QoE measurement platform is described and its collected data examined. The brief concludes with a discussion of future research directions. The example mechanisms and the data-driven architecture provide useful insights into the designs of QoE management, and motivate a new line of thinking for users' satisfaction in future wireless networks.

  14. Synchronous ethernet and IEEE 1588 in telecoms next generation synchronization networks

    CERN Document Server

    2013-01-01

    This book addresses the multiple technical aspects of the distribution of synchronization in new generation telecommunication networks, focusing in particular on synchronous Ethernet and IEEE1588 technologies. Many packet network engineers struggle with understanding the challenges that precise synchronization distribution can impose on networks. The usual “why”, “when” and particularly “how” can cause problems for many engineers. In parallel to this, some other markets have identical synchronization requirements, but with their own design requirements, generating further questions. This book attempts to respond to the different questions by providing background technical information. Invaluable information on state of-the-art packet network synchronization and timing architectures is provided, as well as an unbiased view on the synchronization technologies that have been internationally standardized over recent years, with the aim of providing the average reader (who is not skilled in the art) wi...

  15. Achieving Fair Throughput among TCP Flows in Multi-Hop Wireless Mesh Networks

    Science.gov (United States)

    Hou, Ting-Chao; Hsu, Chih-Wei

    Previous research shows that the IEEE 802.11 DCF channel contention mechanism is not capable of providing throughput fairness among nodes in different locations of the wireless mesh network. The node nearest the gateway will always strive for the chance to transmit data, causing fewer transmission opportunities for the nodes farther from the gateway, resulting in starvation. Prior studies modify the DCF mechanism to address the fairness problem. This paper focuses on the fairness study when TCP flows are carried over wireless mesh networks. By not modifying lower layer protocols, the current work identifies TCP parameters that impact throughput fairness and proposes adjusting those parameters to reduce frame collisions and improve throughput fairness. With the aid of mathematical formulation and ns2 simulations, this study finds that frame transmission from each node can be effectively controlled by properly controlling the delayed ACK timer and using a suitable advertised window. The proposed method reduces frame collisions and greatly improves TCP throughput fairness.

  16. Key handling in wireless sensor networks

    International Nuclear Information System (INIS)

    Li, Y; Newe, T

    2007-01-01

    With the rapid growth of Wireless Sensor Networks (WSNs), many advanced application areas have received significant attention. However, security will be an important factor for their full adoption. Wireless sensor nodes pose unique challenges and as such traditional security protocols, used in traditional networks cannot be applied directly. Some new protocols have been published recently with the goal of providing both privacy of data and authentication of sensor nodes for WSNs. Such protocols can employ private-key and/or public key cryptographic algorithms. Public key algorithms hold the promise of simplifying the network infrastructure required to provide security services such as: privacy, authentication and non-repudiation, while symmetric algorithms require less processing power on the lower power wireless node. In this paper a selection of key establishment/agreement protocols are reviewed and they are broadly divided into two categories: group key agreement protocols and pair-wise key establishment protocols. A summary of the capabilities and security related services provided by each protocol is provided

  17. Experiment of Wireless Sensor Network to Monitor Field Data

    Directory of Open Access Journals (Sweden)

    Kwang Sik Kim

    2009-08-01

    Full Text Available Recently the mobile wireless network has been drastically enhanced and one of the most efficient ways to realize the ubiquitous network will be to develop the converged network by integrating the mobile wireless network with other IP fixed network like NGN (Next Generation Network. So in this paper the term of the wireless ubiquitous network is used to describe this approach. In this paper, first, the wireless ubiquitous network architecture is described based on IMS which has been standardized by 3GPP (3rd Generation Partnership Program. Next, the field data collection system to match the satellite data using location information is proposed based on the concept of the wireless ubiquitous network architecture. The purpose of the proposed system is to provide more accurate analyzing method with the researchers in the remote sensing area.

  18. Maximum Interconnectedness and Availability for Directional Airborne Range Extension Networks

    Science.gov (United States)

    2016-08-29

    Protocols for Wireless Adhoc Networks with Beamforming Antennas", IEEE Communication Surveys and Tutorials , Vol. 14, No. 2, Second Quarter 2012 [10] D... Surveys , Vol. 37, No. 2, June 2005 August 29, 2016 DRAFT 28 IEEE TRANSACTIONS ON WIRELESS COMMUNICATIONS [9] O. Bazan, M. Jaseemuddin, “A Survey On MAC... IEEE TRANSACTIONS ON WIRELESS COMMUNICATIONS 1 Maximum Interconnectedness and Availability for Directional Airborne Range Extension Networks Thomas

  19. Real-Time-Simulation of IEEE-5-Bus Network on OPAL-RT-OP4510 Simulator

    Science.gov (United States)

    Atul Bhandakkar, Anjali; Mathew, Lini, Dr.

    2018-03-01

    The Real-Time Simulator tools have high computing technologies, improved performance. They are widely used for design and improvement of electrical systems. The advancement of the software tools like MATLAB/SIMULINK with its Real-Time Workshop (RTW) and Real-Time Windows Target (RTWT), real-time simulators are used extensively in many engineering fields, such as industry, education, and research institutions. OPAL-RT-OP4510 is a Real-Time Simulator which is used in both industry and academia. In this paper, the real-time simulation of IEEE-5-Bus network is carried out by means of OPAL-RT-OP4510 with CRO and other hardware. The performance of the network is observed with the introduction of fault at various locations. The waveforms of voltage, current, active and reactive power are observed in the MATLAB simulation environment and on the CRO. Also, Load Flow Analysis (LFA) of IEEE-5-Bus network is computed using MATLAB/Simulink power-gui load flow tool.

  20. Cognitive radio wireless sensor networks: applications, challenges and research trends.

    Science.gov (United States)

    Joshi, Gyanendra Prasad; Nam, Seung Yeob; Kim, Sung Won

    2013-08-22

    A cognitive radio wireless sensor network is one of the candidate areas where cognitive techniques can be used for opportunistic spectrum access. Research in this area is still in its infancy, but it is progressing rapidly. The aim of this study is to classify the existing literature of this fast emerging application area of cognitive radio wireless sensor networks, highlight the key research that has already been undertaken, and indicate open problems. This paper describes the advantages of cognitive radio wireless sensor networks, the difference between ad hoc cognitive radio networks, wireless sensor networks, and cognitive radio wireless sensor networks, potential application areas of cognitive radio wireless sensor networks, challenges and research trend in cognitive radio wireless sensor networks. The sensing schemes suited for cognitive radio wireless sensor networks scenarios are discussed with an emphasis on cooperation and spectrum access methods that ensure the availability of the required QoS. Finally, this paper lists several open research challenges aimed at drawing the attention of the readers toward the important issues that need to be addressed before the vision of completely autonomous cognitive radio wireless sensor networks can be realized.

  1. Cognitive Radio Wireless Sensor Networks: Applications, Challenges and Research Trends

    Directory of Open Access Journals (Sweden)

    Gyanendra Prasad Joshi

    2013-08-01

    Full Text Available A cognitive radio wireless sensor network is one of the candidate areas where cognitive techniques can be used for opportunistic spectrum access. Research in this area is still in its infancy, but it is progressing rapidly. The aim of this study is to classify the existing literature of this fast emerging application area of cognitive radio wireless sensor networks, highlight the key research that has already been undertaken, and indicate open problems. This paper describes the advantages of cognitive radio wireless sensor networks, the difference between ad hoc cognitive radio networks, wireless sensor networks, and cognitive radio wireless sensor networks, potential application areas of cognitive radio wireless sensor networks, challenges and research trend in cognitive radio wireless sensor networks. The sensing schemes suited for cognitive radio wireless sensor networks scenarios are discussed with an emphasis on cooperation and spectrum access methods that ensure the availability of the required QoS. Finally, this paper lists several open research challenges aimed at drawing the attention of the readers toward the important issues that need to be addressed before the vision of completely autonomous cognitive radio wireless sensor networks can be realized.

  2. Wireless sensor network for monitoring soil moisture and weather conditions

    Science.gov (United States)

    A wireless sensor network (WSN) was developed and deployed in three fields to monitor soil water status and collect weather data for irrigation scheduling. The WSN consists of soil-water sensors, weather sensors, wireless data loggers, and a wireless modem. Soil-water sensors were installed at three...

  3. Computing Nash Equilibrium in Wireless Ad Hoc Networks: A Simulation-Based Approach

    Directory of Open Access Journals (Sweden)

    Peter Bulychev

    2012-02-01

    Full Text Available This paper studies the problem of computing Nash equilibrium in wireless networks modeled by Weighted Timed Automata. Such formalism comes together with a logic that can be used to describe complex features such as timed energy constraints. Our contribution is a method for solving this problem using Statistical Model Checking. The method has been implemented in UPPAAL model checker and has been applied to the analysis of Aloha CSMA/CD and IEEE 802.15.4 CSMA/CA protocols.

  4. Security in wireless sensor networks

    CERN Document Server

    Oreku, George S

    2016-01-01

    This monograph covers different aspects of sensor network security including new emerging technologies. The authors present a mathematical approach to the topic and give numerous practical examples as well as case studies to illustrate the theory. The target audience primarily comprises experts and practitioners in the field of sensor network security, but the book may also be beneficial for researchers in academia as well as for graduate students.

  5. Industrial wireless sensor networks applications, protocols, and standards

    CERN Document Server

    Güngör, V Çagri

    2013-01-01

    The collaborative nature of industrial wireless sensor networks (IWSNs) brings several advantages over traditional wired industrial monitoring and control systems, including self-organization, rapid deployment, flexibility, and inherent intelligent processing. In this regard, IWSNs play a vital role in creating more reliable, efficient, and productive industrial systems, thus improving companies' competitiveness in the marketplace. Industrial Wireless Sensor Networks: Applications, Protocols, and Standards examines the current state of the art in industrial wireless sensor networks and outline

  6. Performance Analysis of the IEEE 802.11p Multichannel MAC Protocol in Vehicular Ad Hoc Networks.

    Science.gov (United States)

    Song, Caixia

    2017-12-12

    Vehicular Ad Hoc Networks (VANETs) employ multichannel to provide a variety of safety and non-safety applications, based on the IEEE 802.11p and IEEE 1609.4 protocols. The safety applications require timely and reliable transmissions, while the non-safety applications require efficient and high throughput. In the IEEE 1609.4 protocol, operating interval is divided into alternating Control Channel (CCH) interval and Service Channel (SCH) interval with an identical length. During the CCH interval, nodes transmit safety-related messages and control messages, and Enhanced Distributed Channel Access (EDCA) mechanism is employed to allow four Access Categories (ACs) within a station with different priorities according to their criticality for the vehicle's safety. During the SCH interval, the non-safety massages are transmitted. An analytical model is proposed in this paper to evaluate performance, reliability and efficiency of the IEEE 802.11p and IEEE 1609.4 protocols. The proposed model improves the existing work by taking serval aspects and the character of multichannel switching into design consideration. Extensive performance evaluations based on analysis and simulation help to validate the accuracy of the proposed model and analyze the capabilities and limitations of the IEEE 802.11p and IEEE 1609.4 protocols, and enhancement suggestions are given.

  7. Autonomous system for wireless network communication powered by photovoltaic solar energy; Sistema autonomo de comunicacao sem fio em malha alimentado por energia solar fotovoltaica

    Energy Technology Data Exchange (ETDEWEB)

    Alonso, Rafael Herrero

    2009-07-01

    The wireless mesh network communication technology, based on the IEEE802.11 standard, has been a relevant technology solution for wireless networking in the recent years. However, even with the elimination of cables for data communication, the wireless mesh networks have to be connected to a voltage source using an electrical cable that may not be available at the local installation. In this scenario, being Brazil a country located in a tropical zone that receives large annual solar irradiation, the conversion of photons to electricity can be an alternative to eliminate the needs of wiring to the mesh access points. This work contributes to the development of autonomous wireless mesh communication systems powered by solar energy, with easy installation in urban or rural areas. This work also describes its evaluations in aspects such as autonomy, wireless coverage, number of users supported, installation height and throughput. (author)

  8. X-raying neighbour discovery in a wireless sensor network ...

    African Journals Online (AJOL)

    In most wireless sensor networks, the nodes are often assumed to be stationary. However, network connectivity is subject to changes arising from interference in wireless communication, changes in transmission power or loss of synchronization among neighbouring network nodes. Hence, even after a sensor node is aware ...

  9. The Systems Librarian: Implementing Wireless Networks without Compromising Security

    Science.gov (United States)

    Breeding, Marshall

    2005-01-01

    Many libraries are or soon will be offering Wi-Fi, also known as wireless networks. The largest perceived barriers to providing this service are concerns about security. The prime rule when deploying Wi-Fi is segregation, having a clear separation between a public wireless network and the rest of the library?s network. A number of devices can be…

  10. Simple, Reliable, Scalable and Energy Efficient Wireless Sensor Networks

    NARCIS (Netherlands)

    Guo, C.

    2010-01-01

    Wireless communication and networking technology has facilitated people to be connected with each other closely. Cellular network is evolving now from the third generation to the fourth generation. In the meanwhile we are experiencing the demand for wireless networks which can facilitate the

  11. Enhancing the selection of backoff interval using fuzzy logic over wireless Ad Hoc networks.

    Science.gov (United States)

    Ranganathan, Radha; Kannan, Kathiravan

    2015-01-01

    IEEE 802.11 is the de facto standard for medium access over wireless ad hoc network. The collision avoidance mechanism (i.e., random binary exponential backoff-BEB) of IEEE 802.11 DCF (distributed coordination function) is inefficient and unfair especially under heavy load. In the literature, many algorithms have been proposed to tune the contention window (CW) size. However, these algorithms make every node select its backoff interval between [0, CW] in a random and uniform manner. This randomness is incorporated to avoid collisions among the nodes. But this random backoff interval can change the optimal order and frequency of channel access among competing nodes which results in unfairness and increased delay. In this paper, we propose an algorithm that schedules the medium access in a fair and effective manner. This algorithm enhances IEEE 802.11 DCF with additional level of contention resolution that prioritizes the contending nodes according to its queue length and waiting time. Each node computes its unique backoff interval using fuzzy logic based on the input parameters collected from contending nodes through overhearing. We evaluate our algorithm against IEEE 802.11, GDCF (gentle distributed coordination function) protocols using ns-2.35 simulator and show that our algorithm achieves good performance.

  12. Enhancing the Selection of Backoff Interval Using Fuzzy Logic over Wireless Ad Hoc Networks

    Science.gov (United States)

    Ranganathan, Radha; Kannan, Kathiravan

    2015-01-01

    IEEE 802.11 is the de facto standard for medium access over wireless ad hoc network. The collision avoidance mechanism (i.e., random binary exponential backoff—BEB) of IEEE 802.11 DCF (distributed coordination function) is inefficient and unfair especially under heavy load. In the literature, many algorithms have been proposed to tune the contention window (CW) size. However, these algorithms make every node select its backoff interval between [0, CW] in a random and uniform manner. This randomness is incorporated to avoid collisions among the nodes. But this random backoff interval can change the optimal order and frequency of channel access among competing nodes which results in unfairness and increased delay. In this paper, we propose an algorithm that schedules the medium access in a fair and effective manner. This algorithm enhances IEEE 802.11 DCF with additional level of contention resolution that prioritizes the contending nodes according to its queue length and waiting time. Each node computes its unique backoff interval using fuzzy logic based on the input parameters collected from contending nodes through overhearing. We evaluate our algorithm against IEEE 802.11, GDCF (gentle distributed coordination function) protocols using ns-2.35 simulator and show that our algorithm achieves good performance. PMID:25879066

  13. Quality-Aware SCTP in Wireless Networks

    Directory of Open Access Journals (Sweden)

    Jen-Yi Pan

    2010-01-01

    Full Text Available SCTP (Stream control transmission protocol is a new transport layer protocol that was published as RFC2960 by IETF (the Internet Engineering Task Force in October 2000 and amended in RFC4960 in September 2007. SCTP provides reliable ordered and unordered transport services. The congestion control and flow control mechanisms for SCTP are very similar to those for TCP (transmission control protocol. SCTP can apply more than one IP address when establishing associations. SCTP multihoming can support multiple paths in association. These features provide SCTP with some network-level fault tolerance through network address redundancy. SCTP multihoming has tremendous transmission potential. However, SCTP path management is very simple in RFC4960 and therefore cannot effectively distinguish path conditions; it also has no path switch strategy appropriate for wireless networking. These factors all degrade SCTP performance. This study proposes a new path management (quality-aware SCTP for wireless networks; this includes a new path failure detection method and ICE (idle path congestion window size estimation mechanism. An experiment using NS2 was performed, showing that quality-aware SCTP can effectively improve the network performance. Quality-aware SCTP is simple and provides a more effective performance than SCTP alone.

  14. Intelligent Devices in Rural Wireless Networks

    Directory of Open Access Journals (Sweden)

    Daniel FUENTES

    2014-03-01

    Full Text Available The rural wireless networks are increasingly in demand by associations and autarchies to expand Internet access in this type of areas. The problem of such solutions centers not only in network deployment and its maintenance, but also in the equipment installation on clients, which always has big costs. This installation and configuration must be performed by a technician on site, so that the equipment can be integrated in the infrastructure. To try to mitigate this problem, it is presented a solution that allows the clients to install, with transparency, the device at home, reducing not only the cost for the management entity but also for the clients. This way, for info-excluded people or with new technology low experience level, it is the user that integrates himself in the network, making him part of the process, fostering the network usage.In this article are specified not only the system architecture but also the way that it works and how it obtains the desirable result. The tests made to the solution show the quickness, reliability and autonomy in the execution of the tasks, making it a benefit for rural wireless networks.This solution, by its robustness and simplicity, allowed an uptake to the IT by people who never thought to do it, namely an advanced age group (elderly who want to join the world of the new technologies

  15. Expected Transmission Energy Route Metric for Wireless Mesh Senor Networks

    Directory of Open Access Journals (Sweden)

    YanLiang Jin

    2011-01-01

    Full Text Available Mesh is a network topology that achieves high throughput and stable intercommunication. With great potential, it is expected to be the key architecture of future networks. Wireless sensor networks are an active research area with numerous workshops and conferences arranged each year. The overall performance of a WSN highly depends on the energy consumption of the network. This paper designs a new routing metric for wireless mesh sensor networks. Results from simulation experiments reveal that the new metric algorithm improves the energy balance of the whole network and extends the lifetime of wireless mesh sensor networks (WMSNs.

  16. Implementation of Energy Efficiency Based on Time Scheduling to Improve Network Lifetime in Wireless Body Area Network (WBAN

    Directory of Open Access Journals (Sweden)

    Subono .

    2016-04-01

    Full Text Available ZigBee applications of IEEE 802.15.4 Wireless Sensor Network (WSN with Low Rate Wireless Personal Area Network (LR-WPAN can be integrated with e-health technology Wireless Body Area Network (WBAN. WBAN are small size and can communicate quickly making it easier for people to obtain information accurately.WBAN has a variety of functions that can help human life. It can be used in the e-health, military and sports. WBAN has the potential to be the future of wireless communication solutions. WBAN use battery as its primary power source. WBAN has limited energy and must be able to save energy consumption in order to operate for a long time. In this study, we propose a method of time scheduling called cycle sleep period (CSP as WBAN solutions to save energy and improve energy efficiency. The CSP method is implemented in the real hardware testbed using sensor e-health includes temperature body and current sensor. We compared the performance of CSP method with duty cycle management (DCM time scheduling-based and without using time scheduling.From the measurement results, our proposed idea has decreasingenergy consumption. Keywords: WSN, LR-WPAN, WBAN, e-health, Time Scheduling

  17. Mechanisms for Prolonging Network Lifetime in Wireless Sensor Networks

    Science.gov (United States)

    Yang, Yinying

    2010-01-01

    Sensors are used to monitor and control the physical environment. A Wireless Sensor Network (WSN) is composed of a large number of sensor nodes that are densely deployed either inside the phenomenon or very close to it [18][5]. Sensor nodes measure various parameters of the environment and transmit data collected to one or more sinks, using…

  18. Graphical Model Theory for Wireless Sensor Networks

    International Nuclear Information System (INIS)

    Davis, William B.

    2002-01-01

    Information processing in sensor networks, with many small processors, demands a theory of computation that allows the minimization of processing effort, and the distribution of this effort throughout the network. Graphical model theory provides a probabilistic theory of computation that explicitly addresses complexity and decentralization for optimizing network computation. The junction tree algorithm, for decentralized inference on graphical probability models, can be instantiated in a variety of applications useful for wireless sensor networks, including: sensor validation and fusion; data compression and channel coding; expert systems, with decentralized data structures, and efficient local queries; pattern classification, and machine learning. Graphical models for these applications are sketched, and a model of dynamic sensor validation and fusion is presented in more depth, to illustrate the junction tree algorithm

  19. Wireless traffic steering for green cellular networks

    CERN Document Server

    Zhang, Shan; Zhou, Sheng; Niu, Zhisheng; Shen, Xuemin (Sherman)

    2016-01-01

    This book introduces wireless traffic steering as a paradigm to realize green communication in multi-tier heterogeneous cellular networks. By matching network resources and dynamic mobile traffic demand, traffic steering helps to reduce on-grid power consumption with on-demand services provided. This book reviews existing solutions from the perspectives of energy consumption reduction and renewable energy harvesting. Specifically, it explains how traffic steering can improve energy efficiency through intelligent traffic-resource matching. Several promising traffic steering approaches for dynamic network planning and renewable energy demand-supply balancing are discussed. This book presents an energy-aware traffic steering method for networks with energy harvesting, which optimizes the traffic allocated to each cell based on the renewable energy status. Renewable energy demand-supply balancing is a key factor in energy dynamics, aimed at enhancing renewable energy sustainability to reduce on-grid energy consum...

  20. Graphical Model Theory for Wireless Sensor Networks

    Energy Technology Data Exchange (ETDEWEB)

    Davis, William B.

    2002-12-08

    Information processing in sensor networks, with many small processors, demands a theory of computation that allows the minimization of processing effort, and the distribution of this effort throughout the network. Graphical model theory provides a probabilistic theory of computation that explicitly addresses complexity and decentralization for optimizing network computation. The junction tree algorithm, for decentralized inference on graphical probability models, can be instantiated in a variety of applications useful for wireless sensor networks, including: sensor validation and fusion; data compression and channel coding; expert systems, with decentralized data structures, and efficient local queries; pattern classification, and machine learning. Graphical models for these applications are sketched, and a model of dynamic sensor validation and fusion is presented in more depth, to illustrate the junction tree algorithm.

  1. Wireless Sensor Network Based Smart Parking System

    Directory of Open Access Journals (Sweden)

    Jeffrey JOSEPH

    2014-01-01

    Full Text Available Ambient Intelligence is a vision in which various devices come together and process information from multiple sources in order to exert control on the physical environment. In addition to computation and control, communication plays a crucial role in the overall functionality of such a system. Wireless Sensor Networks are one such class of networks, which meet these criteria. These networks consist of spatially distributed sensor motes which work in a co-operative manner to sense and control the environment. In this work, an implementation of an energy-efficient and cost-effective, wireless sensor networks based vehicle parking system for a multi-floor indoor parking facility has been introduced. The system monitors the availability of free parking slots and guides the vehicle to the nearest free slot. The amount of time the vehicle has been parked is monitored for billing purposes. The status of the motes (dead/alive is also recorded. Information like slot allocated, directions to the slot and billing data is sent as a message to customer’s mobile phones. This paper extends our previous work 1 with the development of a low cost sensor mote, about one tenth the cost of a commercially available mote, keeping in mind the price sensitive markets of the developing countries.

  2. Wireless intelligent network: infrastructure before services?

    Science.gov (United States)

    Chu, Narisa N.

    1996-01-01

    The Wireless Intelligent Network (WIN) intends to take advantage of the Advanced Intelligent Network (AIN) concepts and products developed from wireline communications. However, progress of the AIN deployment has been slow due to the many barriers that exist in the traditional wireline carriers' deployment procedures and infrastructure. The success of AIN has not been truly demonstrated. The AIN objectives and directions are applicable to the wireless industry although the plans and implementations could be significantly different. This paper points out WIN characteristics in architecture, flexibility, deployment, and value to customers. In order to succeed, the technology driven AIN concept has to be reinforced by the market driven WIN services. An infrastructure suitable for the WIN will contain elements that are foreign to the wireline network. The deployment process is expected to seed with the revenue generated services. Standardization will be achieved by simplifying and incorporating the IS-41C, AIN, and Intelligent Network CS-1 recommendations. Integration of the existing and future systems impose the biggest challenge of all. Service creation has to be complemented with service deployment process which heavily impact the carriers' infrastructure. WIN deployment will likely start from an Intelligent Peripheral, a Service Control Point and migrate to a Service Node when sufficient triggers are implemented in the mobile switch for distributed call control. The struggle to move forward will not be based on technology, but rather on the impact to existing infrastructure.

  3. Homomorphic Filtering for Improving Time Synchronization in Wireless Networks

    Science.gov (United States)

    Castillo-Secilla, José María; Palomares, José Manuel; León, Fernando; Olivares, Joaquín

    2017-01-01

    Wireless sensor networks are used to sample the environment in a distributed way. Therefore, it is mandatory for all of the measurements to be tightly synchronized in order to guarantee that every sensor is sampling the environment at the exact same instant of time. The synchronization drift gets bigger in environments suffering from temperature variations. Thus, this work is focused on improving time synchronization under deployments with temperature variations. The working hypothesis demonstrated in this work is that the clock skew of two nodes (the ratio of the real frequencies of the oscillators) is composed of a multiplicative combination of two main components: the clock skew due to the variations between the cut of the crystal of each oscillator and the clock skew due to the different temperatures affecting the nodes. By applying a nonlinear filtering, the homomorphic filtering, both components are separated in an effective way. A correction factor based on temperature, which can be applied to any synchronization protocol, is proposed. For testing it, an improvement of the FTSP synchronization protocol has been developed and physically tested under temperature variation scenarios using TelosB motes flashed with the IEEE 802.15.4 implementation supplied by TinyOS. PMID:28425955

  4. Low complexity detectors for cooperative wireless sensor networks

    KAUST Repository

    Ahmed, Qasim Zeeshan

    2012-09-01

    This paper investigates and compares the performance of wireless sensor networks (WSN) when sensors operate on the principles of cooperative communications. We consider a scenario where the source transmits signals to the destination with the help of L sensors. As the destination has the capacity of processing only U out of these L signals, U strongest signals are selected while the remaining (L - U) signals are suppressed. A preprocessing block similar to channel-shortening (CS) is proposed in this contribution. However, this preprocessing block employs rank-reduction technique instead of CS. This detector operates on the principles of principal components (PC). From our simulations it can be observed that this detector is capable of achieving a similar bit error rate (BER) performance as the full-rank MMSE detector with significantly lower complexity. It outperforms the CS-based detector in terms of BER performance when using fixed amplification factor. However, for variable gain amplification factor a tradeoff between the diversity gain and the receiver complexity can be observed. From the simulations it can be concluded that the BER performance of the PC-based detector when using variable gain amplification factor are better than that of the CS-based detector for lower signal to noise ratio. © 2012 IEEE.

  5. Quality of Service Model on Data Link Layer for Mission Critical Traffic on IEEE 802.11g Networks in Infrastructure Mode

    Directory of Open Access Journals (Sweden)

    Gerald B. Fuenmayor-Rivadeneira

    2013-11-01

    Full Text Available This article presents a synthesized review as state of the art of the study of QoS for mission-critical traffic in wireless local area networks that use the IEEE 802.11g protocol. This is to highlight previous research for their contribution will constitute a reference to guide a proposed new approach to ensuring the quality of service for this type of traffic using the above protocol. The review is based on academic and business items made during the current five years. As a result of this review it is evident that there have been many efforts to address the issue but there are still gaps in the characterization of mission-critical traffic and ensuring quality of service for the same, due the new applications and the large host of WiFi networks in business and government, which has led to increased demand for access channels and, therefore, a challenge to the progress already known, such as IEEE 802.1q.

  6. Physical Layer Network Coding

    DEFF Research Database (Denmark)

    Fukui, Hironori; Yomo, Hironori; Popovski, Petar

    2013-01-01

    /receive interference. The way to deal with this problem in distributed wireless networks is usage of MAC-layer mechanisms that make a spatial reservation of the shared wireless medium, similar to the well-known RTS/CTS in IEEE 802.11 wireless networks. In this paper, we investigate two-way relaying in presence...

  7. Cross-layer active predictive congestion control protocol for wireless sensor networks.

    Science.gov (United States)

    Wan, Jiangwen; Xu, Xiaofeng; Feng, Renjian; Wu, Yinfeng

    2009-01-01

    In wireless sensor networks (WSNs), there are numerous factors that may cause network congestion problems, such as the many-to-one communication modes, mutual interference of wireless links, dynamic changes of network topology and the memory-restrained characteristics of nodes. All these factors result in a network being more vulnerable to congestion. In this paper, a cross-layer active predictive congestion control scheme (CL-APCC) for improving the performance of networks is proposed. Queuing theory is applied in the CL-APCC to analyze data flows of a single-node according to its memory status, combined with the analysis of the average occupied memory size of local networks. It also analyzes the current data change trends of local networks to forecast and actively adjust the sending rate of the node in the next period. In order to ensure the fairness and timeliness of the network, the IEEE 802.11 protocol is revised based on waiting time, the number of the node's neighbors and the original priority of data packets, which dynamically adjusts the sending priority of the node. The performance of CL-APCC, which is evaluated by extensive simulation experiments. is more efficient in solving the congestion in WSNs. Furthermore, it is clear that the proposed scheme has an outstanding advantage in terms of improving the fairness and lifetime of networks.

  8. Cross-Layer Active Predictive Congestion Control Protocol for Wireless Sensor Networks

    Directory of Open Access Journals (Sweden)

    Yinfeng Wu

    2009-10-01

    Full Text Available In wireless sensor networks (WSNs, there are numerous factors that may cause network congestion problems, such as the many-to-one communication modes, mutual interference of wireless links, dynamic changes of network topology and the memory-restrained characteristics of nodes. All these factors result in a network being more vulnerable to congestion. In this paper, a cross-layer active predictive congestion control scheme (CL-APCC for improving the performance of networks is proposed. Queuing theory is applied in the CL-APCC to analyze data flows of a single-node according to its memory status, combined with the analysis of the average occupied memory size of local networks. It also analyzes the current data change trends of local networks to forecast and actively adjust the sending rate of the node in the next period. In order to ensure the fairness and timeliness of the network, the IEEE 802.11 protocol is revised based on waiting time, the number of the node‟s neighbors and the original priority of data packets, which dynamically adjusts the sending priority of the node. The performance of CL-APCC, which is evaluated by extensive simulation experiments. is more efficient in solving the congestion in WSNs. Furthermore, it is clear that the proposed scheme has an outstanding advantage in terms of improving the fairness and lifetime of networks.

  9. Sub-Frame Crossing for Streaming Video over Wireless Networks

    OpenAIRE

    Aziz, Hussein Muzahim; Grahn, Håkan; Lundberg, Lars

    2010-01-01

    Transmitting a real time video streaming over a wireless network cannot guarantee that all the frames could be received by the mobile devices. The characteristics of a wireless network in terms of the available bandwidth, frame delay, and frame losses cannot be known in advanced. In this work, we propose a new mechanism for streaming video over a wireless channel. The proposed mechanism prevents freezing frames in the mobile devices. This is done by splitting the video frame in two sub-frames...

  10. Wireless motion sensor network for monitoring motion in a process, wireless sensor node, reasoning node, and feedback and/or actuation node for such wireless motion sensor network

    NARCIS (Netherlands)

    Havinga, Paul J.M.; Marin Perianu, Raluca; Marin Perianu, Mihai

    2010-01-01

    Wireless motion sensor network for monitoring motion in a process comprising at least one wireless sensor node for measuring at least one physical quantity related to motion or orientation, feature extraction means for deriving a feature for the measured quantities, a wireless transmitter connected

  11. Downlink interference suppression of 802.11ac wireless network

    Directory of Open Access Journals (Sweden)

    WANG Huan

    2016-04-01

    Full Text Available In the 802.11ac wireless local area network,wireless intelligent devices(WID need to be connected to the network through the wireless access point(AP,and other wireless APs in the downlink transmission process will cause interference to the target WID.In this paper,we propose a method based on iterative minimum mean square error interference alignment,which can suppress the interference from the other wireless APs to the target WIDs.The wireless access terminal and wireless smart devices have designed linear precode and decode respectively.Under the minimum mean square error criterion and limitation the power constraint,optimal precode and decode can be received.Simulation results show that the proposed method,when the signal to noise ratio is 5 dB,the transmission rate of the unit bandwidth transmission rate is increased by 1 bit/s compared with the traditional Max-SINR algorithm.

  12. Fault Detection for Large-Scale Railway Maintenance Equipment Base on Wireless Sensor Networks

    Directory of Open Access Journals (Sweden)

    Junfu Yu

    2014-04-01

    Full Text Available Focusing on the fault detection application for large-scale railway maintenance equipment with the specialties of low-cost, energy efficiency, collecting data of the function units. This paper proposed energy efficiency, convenient installation fault detection application using Sigsbee wireless sensor networks, which Sigsbee is the most widely used protocol based on IEEE 802.15.4. This paper proposed a systematic application from hardware design using STM32F103 chips as processer, to software system. Fault detection application is the basic part of the fault diagnose system, wireless sensor nodes of the fault detection application with different kinds of sensors for verities function units communication by Sigsbee to collecting and sending basic working status data to the home gateway, then data will be sent to the fault diagnose system.

  13. Indoor location system based on discriminant-adaptive neural network in IEEE 802.11 environments.

    Science.gov (United States)

    Fang, Shih-Hau; Lin, Tsung-Nan

    2008-11-01

    This brief paper presents a novel localization algorithm, named discriminant-adaptive neural network (DANN), which takes the received signal strength (RSS) from the access points (APs) as inputs to infer the client position in the wireless local area network (LAN) environment. We extract the useful information into discriminative components (DCs) for network learning. The nonlinear relationship between RSS and the position is then accurately constructed by incrementally inserting the DCs and recursively updating the weightings in the network until no further improvement is required. Our localization system is developed in a real-world wireless LAN WLAN environment, where the realistic RSS measurement is collected. We implement the traditional approaches on the same test bed, including weighted kappa-nearest neighbor (WKNN), maximum likelihood (ML), and multilayer perceptron (MLP), and compare the results. The experimental results indicate that the proposed algorithm is much higher in accuracy compared with other examined techniques. The improvement can be attributed to that only the useful information is efficiently extracted for positioning while the redundant information is regarded as noise and discarded. Finally, the analysis shows that our network intelligently accomplishes learning while the inserted DCs provide sufficient information.

  14. Security Threats in Wireless Sensor Networks

    DEFF Research Database (Denmark)

    Giannetsos, Athanasios

    2011-01-01

    . Security and privacy are rapidly replacing performance as the first and foremost concern in many sensor networking scenarios. While security prevention is important, it cannot guarantee that attacks will not be launched and that, once launched, they will not be successful. Therefore, detection of malicious...... intrusions forms an important part of an integrated approach to network security. In this work, we start by considering the problem of cooperative intrusion detection in WSNs and develop a lightweight ID system, called LIDeA, which follows an intelligent agent-based architecture. We show how such a system...... networks are. Motivated by this unexplored security aspect, we investigate a new set of memory related vulnerabilities for sensor embedded devices that, if exploited, can lead to the execution of software-based attacks. We demonstrate how to execute malware on wireless sensor nodes that are based...

  15. Audio coding in wireless acoustic sensor networks

    DEFF Research Database (Denmark)

    Zahedi, Adel; Østergaard, Jan; Jensen, Søren Holdt

    2015-01-01

    ) for the resulting remote DSC problem under covariance matrix distortion constraints. We further show that for this problem, the Gaussian source is the worst to code. Thus, the Gaussian RDF provides an upper bound to other sources such as audio signals. We then turn our attention to audio signals. We consider......In this paper, we consider the problem of source coding for a wireless acoustic sensor network where each node in the network makes its own noisy measurement of the sound field, and communicates with other nodes in the network by sending and receiving encoded versions of the measurements. To make...... use of the correlation between the sources available at the nodes, we consider the possibility of combining the measurement and the received messages into one single message at each node instead of forwarding the received messages and separate encoding of the measurement. Moreover, to exploit...

  16. Node clustering for wireless sensor networks

    International Nuclear Information System (INIS)

    Bhatti, S.; Qureshi, I.A.; Memon, S.

    2012-01-01

    Recent years have witnessed considerable growth in the development and deployment of clustering methods which are not only used to maintain network resources but also increases the reliability of the WSNs (Wireless Sensor Network) and the facts manifest by the wide range of clustering solutions. Node clustering by selecting key parameters to tackle the dynamic behaviour of resource constraint WSN is a challenging issue. This paper highlights the recent progress which has been carried out pertaining to the development of clustering solutions for the WSNs. The paper presents classification of node clustering methods and their comparison based on the objectives, clustering criteria and methodology. In addition, the potential open issues which need to be considered for future work are high lighted. Keywords: Clustering, Sensor Network, Static, Dynamic

  17. Cross-platform wireless sensor network development

    DEFF Research Database (Denmark)

    Hansen, Morten Tranberg; Kusy, Branislav

    Design and development of wireless sensor network applications adds an additional layer of complexity to traditional computer systems. The developer needs to be an expert in resource constrained embedded devices as well as traditional desktop computers. We propose Tinylnventor, an open......-source development environment that takes a holistic approach to implementing sensor network applications. Users build applications using a drag-and-drop visual programming language Open Blocks, a language that Google selected for its App Inventor for Android. Tinylnventor uses cross-platform programming concepts......, such as threads and common network operations, to provide a unified environment from which it generates application binaries for the respective platforms. We demonstrate through an application example that Tinylnventor is both simple to use and powerful in expressing complex applications....

  18. Autonomic Context-Aware Wireless Sensor Networks

    Directory of Open Access Journals (Sweden)

    Nídia G. S. Campos

    2015-01-01

    Full Text Available Autonomic Computing allows systems like wireless sensor networks (WSN to self-manage computing resources in order to extend their autonomy as much as possible. In addition, contextualization tasks can fuse two or more different sensor data into a more meaningful information. Since these tasks usually run in a single centralized context server (e.g., sink node, the massive volume of data generated by the wireless sensors can lead to a huge information overload in such server. Here we propose DAIM, a distributed autonomic inference machine distributed which allows the sensor nodes to do self-management and contextualization tasks based on fuzzy logic. We have evaluated DAIM in a real sensor network taking into account other inference machines. Experimental results illustrate that DAIM is an energy-efficient contextualization method for WSN, reducing 48.8% of the number of messages sent to the context servers while saving 19.5% of the total amount of energy spent in the network.

  19. Track classification within wireless sensor network

    Science.gov (United States)

    Doumerc, Robin; Pannetier, Benjamin; Moras, Julien; Dezert, Jean; Canevet, Loic

    2017-05-01

    In this paper, we present our study on track classification by taking into account environmental information and target estimated states. The tracker uses several motion model adapted to different target dynamics (pedestrian, ground vehicle and SUAV, i.e. small unmanned aerial vehicle) and works in centralized architecture. The main idea is to explore both: classification given by heterogeneous sensors and classification obtained with our fusion module. The fusion module, presented in his paper, provides a class on each track according to track location, velocity and associated uncertainty. To model the likelihood on each class, a fuzzy approach is used considering constraints on target capability to move in the environment. Then the evidential reasoning approach based on Dempster-Shafer Theory (DST) is used to perform a time integration of this classifier output. The fusion rules are tested and compared on real data obtained with our wireless sensor network.In order to handle realistic ground target tracking scenarios, we use an autonomous smart computer deposited in the surveillance area. After the calibration step of the heterogeneous sensor network, our system is able to handle real data from a wireless ground sensor network. The performance of this system is evaluated in a real exercise for intelligence operation ("hunter hunt" scenario).

  20. Transmit Power Optimisation in Wireless Network

    Directory of Open Access Journals (Sweden)

    Besnik Terziu

    2011-09-01

    Full Text Available Transmit power optimisation in wireless networks based on beamforming have emerged as a promising technique to enhance the spectrum efficiency of present and future wireless communication systems. The aim of this study is to minimise the access point power consumption in cellular networks while maintaining a targeted quality of service (QoS for the mobile terminals. In this study, the targeted quality of service is delivered to a mobile station by providing a desired level of Signal to Interference and Noise Ratio (SINR. Base-stations are coordinated across multiple cells in a multi-antenna beamforming system. This study focuses on a multi-cell multi-antenna downlink scenario where each mobile user is equipped with a single antenna, but where multiple mobile users may be active simultaneously in each cell and are separated via spatial multiplexing using beamforming. The design criteria is to minimize the total weighted transmitted power across the base-stations subject to SINR constraints at the mobile users. The main contribution of this study is to define an iterative algorithm that is capable of finding the joint optimal beamformers for all basestations, based on a correlation-based channel model, the full-correlation model. Among all correlated channel models, the correlated channel model used in this study is the most accurate, giving the best performance in terms of power consumption. The environment here in this study is chosen to be Non-Light of- Sight (NLOS condition, where a signal from a wireless transmitter passes several obstructions before arriving at a wireless receiver. Moreover there are many scatterers local to the mobile, and multiple reflections can occur among them before energy arrives at the mobile. The proposed algorithm is based on uplink-downlink duality using the Lagrangian duality theory. Time-Division Duplex (TDD is chosen as the platform for this study since it has been adopted to the latest technologies in Fourth

  1. Wireless sensor networks from theory to applications

    CERN Document Server

    El Emary, Ibrahiem M M

    2013-01-01

    Although there are many books available on WSNs, most are low-level, introductory books. The few available for advanced readers fail to convey the breadth of knowledge required for those aiming to develop next-generation solutions for WSNs. Filling this void, Wireless Sensor Networks: From Theory to Applications supplies comprehensive coverage of WSNs. In order to provide the wide-ranging guidance required, the book brings together the contributions of domain experts working in the various subfields of WSNs worldwide. This edited volume examines recent advances in WSN technologies and consider

  2. Nonlinear Gossip Algorithms for Wireless Sensor Networks

    Directory of Open Access Journals (Sweden)

    Chao Shi

    2014-01-01

    Full Text Available We study some nonlinear gossip algorithms for wireless sensor networks. Firstly, two types of nonlinear single gossip algorithms are proposed. By using Lyapunov theory, Lagrange mean value theorem, and stochastic Lasalle’s invariance principle, we prove that the nonlinear single gossip algorithms can converge to the average of initial states with probability one. Secondly, two types of nonlinear multigossip algorithms are also presented and the convergence is proved by the same methods. Finally, computer simulation is also given to show the validity of the theoretical results.

  3. BABY MONITORING SYSTEM USING WIRELESS SENSOR NETWORKS

    Directory of Open Access Journals (Sweden)

    G. Rajesh

    2014-09-01

    Full Text Available Sudden Infant Death Syndrome (SIDS is marked by the sudden death of an infant during sleep that is not predicted by the medical history and remains unexplained even after thorough forensic autopsy and detailed death investigation. In this we developed a system that provides solutions for the above problems by making the crib smart using the wireless sensor networks (WSN and smart phones. The system provides visual monitoring service through live video, alert services by crib fencing and awakens alert, monitoring services by temperature reading and light intensity reading, vaccine reminder and weight monitoring.

  4. Wireless sensor networks and ecological monitoring

    CERN Document Server

    Jiang, Joe-Air

    2013-01-01

    This book presents the state of the art technologies and solutions to tackle the critical challenges faced by the building and development of the WSN and ecological monitoring system but also potential impact on society at social, medical and technological level. This book is dedicated to Sensing systems for Sensors, Wireless Sensor Networks and Ecological Monitoring. The book aims at Master and PhD degree students, researchers, practitioners, especially WSN engineers involved with ecological monitoring. The book will provide an opportunity of a dedicated and a deep approach in order to improve their knowledge in this specific field.  

  5. Acknowledgement Corruption: A New Aspect of Physical Layer Capture in IEEE 802.11 Networks

    Directory of Open Access Journals (Sweden)

    Jung-Han Han

    2018-01-01

    Full Text Available Even if a collision occurs in IEEE 802.11 network, a transmission may be successfully decoded at the receiver if the signal strength of one transmission is sufficiently stronger than the other transmission. This phenomenon is called “Physical Layer Capture” (PLC. While existing works have considered PLC between data frames, in this paper we investigate the case that an ACK frame collides with the unfinished transmission of other data frames after the occurrence of PLC between data frames. As a result of this collision, the ACK frame may be corrupted and the corresponding data frame needs to be retransmitted. We call this phenomenon “ACK Corruption” (AC. We identify the characteristic of AC via extensive experiments and simulations. Our study reveals that AC can occur in all IEEE 802.11 variants and its chance is dependent upon the relative signal strength between the stations and the MCS setting used. Further, we devise a way to avoid AC occurrence and evaluate its effectiveness.

  6. FPGA implementation of a ZigBee wireless network control interface to transmit biomedical signals

    Science.gov (United States)

    Gómez López, M. A.; Goy, C. B.; Bolognini, P. C.; Herrera, M. C.

    2011-12-01

    In recent years, cardiac hemodynamic monitors have incorporated new technologies based on wireless sensor networks which can implement different types of communication protocols. More precisely, a digital conductance catheter system recently developed adds a wireless ZigBee module (IEEE 802.15.4 standards) to transmit cardiac signals (ECG, intraventricular pressure and volume) which would allow the physicians to evaluate the patient's cardiac status in a noninvasively way. The aim of this paper is to describe a control interface, implemented in a FPGA device, to manage a ZigBee wireless network. ZigBee technology is used due to its excellent performance including simplicity, low-power consumption, short-range transmission and low cost. FPGA internal memory stores 8-bit signals with which the control interface prepares the information packets. These data were send to the ZigBee END DEVICE module that receives and transmits wirelessly to the external COORDINATOR module. Using an USB port, the COORDINATOR sends the signals to a personal computer for displaying. Each functional block of control interface was assessed by means of temporal diagrams. Three biological signals, organized in packets and converted to RS232 serial protocol, were sucessfully transmitted and displayed in a PC screen. For this purpose, a custom-made graphical software was designed using LabView.

  7. FPGA implementation of a ZigBee wireless network control interface to transmit biomedical signals

    International Nuclear Information System (INIS)

    López, M A Gómez; Goy, C B; Bolognini, P C; Herrera, M C

    2011-01-01

    In recent years, cardiac hemodynamic monitors have incorporated new technologies based on wireless sensor networks which can implement different types of communication protocols. More precisely, a digital conductance catheter system recently developed adds a wireless ZigBee module (IEEE 802.15.4 standards) to transmit cardiac signals (ECG, intraventricular pressure and volume) which would allow the physicians to evaluate the patient's cardiac status in a noninvasively way. The aim of this paper is to describe a control interface, implemented in a FPGA device, to manage a ZigBee wireless network. ZigBee technology is used due to its excellent performance including simplicity, low-power consumption, short-range transmission and low cost. FPGA internal memory stores 8-bit signals with which the control interface prepares the information packets. These data were send to the ZigBee END DEVICE module that receives and transmits wirelessly to the external COORDINATOR module. Using an USB port, the COORDINATOR sends the signals to a personal computer for displaying. Each functional block of control interface was assessed by means of temporal diagrams. Three biological signals, organized in packets and converted to RS232 serial protocol, were successfully transmitted and displayed in a PC screen. For this purpose, a custom-made graphical software was designed using LabView.

  8. Wireless multimedia sensor networks on reconfigurable hardware information reduction techniques

    CERN Document Server

    Ang, Li-minn; Chew, Li Wern; Yeong, Lee Seng; Chia, Wai Chong

    2013-01-01

    Traditional wireless sensor networks (WSNs) capture scalar data such as temperature, vibration, pressure, or humidity. Motivated by the success of WSNs and also with the emergence of new technology in the form of low-cost image sensors, researchers have proposed combining image and audio sensors with WSNs to form wireless multimedia sensor networks (WMSNs).

  9. Network Coding Opportunities for Wireless Grids Formed by Mobile Devices

    DEFF Research Database (Denmark)

    Nielsen, Karsten Fyhn; Madsen, Tatiana Kozlova; Fitzek, Frank

    2008-01-01

    Wireless grids have potential in sharing communication, computational and storage resources making these networks more powerful, more robust, and less cost intensive. However, to enjoy the benefits of cooperative resource sharing, a number of issues should be addressed and the cost of the wireles...... implementation demonstrates the feasibility of network coding for wireless grids formed by mobile devices....

  10. A tutorial survey of topics in wireless networking: Part I

    Indian Academy of Sciences (India)

    for the environment of an office building or hotel, or a large chemical factory. 3. Technical elements. In the previous section we have provided an overview of the current practice of wireless networks. We organised our presentation around a taxonomy of wireless networks shown in figure 1. Although the technologies that we ...

  11. Method and system for localization in a wireless network

    NARCIS (Netherlands)

    Havinga, Paul J.M.; Dil, B.J.

    2011-01-01

    The present invention relates to a method and system for localization in wireless networks. More in particular, the present invention is relates to Received Signal Strength (RSS) based localization in wireless networks, such as localization based on Radio Interferometric Positioning (RIP). Unlike

  12. Wireless sensor network for irrigation application in cotton

    Science.gov (United States)

    A wireless sensor network was deployed in a cotton field to monitor soil water status for irrigation. The network included two systems, a Decagon system and a microcontroller-based system. The Decagon system consists of soil volumetric water-content sensors, wireless data loggers, and a central data...

  13. Collaborative Algorithms for Communication in Wireless Sensor Networks

    NARCIS (Netherlands)

    Nieberg, T.; Dulman, S.O.; Havinga, Paul J.M.; van Hoesel, L.F.W.; Wu Jian, W.J.; Basten, Twan; Geilen, Marc; de Groot, Harmke

    2003-01-01

    In this paper, we present the design of the communication in a wireless sensor network. The resource limitations of a wireless sensor network, especially in terms of energy, require an integrated, and collaborative approach for the different layers of communication. In particular, energy-efficient

  14. Collaborative Algortihms for Communication in Wireless Sensor Networks

    NARCIS (Netherlands)

    Nieberg, T.; Dulman, S.O.; Havinga, Paul J.M.; van Hoesel, L.F.W.; Wu Jian, W.J.

    In this paper, we present the design of the communication in a wireless sensor network. The resource limitations of a wireless sensor network, especially in terms of energy, require an integrated, and collaborative approach for the different layers of communication. In particular, energy-efficient

  15. Energy Efficient Routing in Wireless Sensor Networks based on Ant ...

    African Journals Online (AJOL)

    Wireless Sensor Networks (WSN's) have become an important and challenging research area in recent years. Wireless Sensor Networks consisting of nodes with limited power are deployed to gather useful information from the field. In WSNs it is critical to collect the information in an energy efficient manner. Ant Colony ...

  16. Convergence of wireless, wireline, and photonics next generation networks

    CERN Document Server

    Iniewski, Krzysztof

    2010-01-01

    Filled with illustrations and practical examples from industry, this book provides a brief but comprehensive introduction to the next-generation wireless networks that will soon replace more traditional wired technologies. Written by a mixture of top industrial experts and key academic professors, it is the only book available that covers both wireless networks (such as wireless local area and personal area networks) and optical networks (such as long-haul and metropolitan networks) in one volume. It gives engineers and engineering students the necessary knowledge to meet challenges of next-ge

  17. Software defined wireless sensor networks application opportunities for efficient network management: a survey

    CSIR Research Space (South Africa)

    Modieginyane, KM

    2017-03-01

    Full Text Available Wireless Sensor Networks (WSNs) are commonly used information technologies of modern networking and computing platforms. Today's network computing applications are faced with a high demand of powerful network functionalities. Functional network...

  18. Low-power secure body area network for vital sensors toward IEEE802.15.6.

    Science.gov (United States)

    Kuroda, Masahiro; Qiu, Shuye; Tochikubo, Osamu

    2009-01-01

    Many healthcare/medical services have started using personal area networks, such as Bluetooth and ZigBee; these networks consist of various types of vital sensors. These works focus on generalized functions for sensor networks that expect enough battery capacity and low-power CPU/RF (Radio Frequency) modules, but less attention to easy-to-use privacy protection. In this paper, we propose a commercially-deployable secure body area network (S-BAN) with reduced computational burden on a real sensor that has limited RAM/ROM sizes and CPU/RF power consumption under a light-weight battery. Our proposed S-BAN provides vital data ordering among sensors that are involved in an S-BAN and also provides low-power networking with zero-administration security by automatic private key generation. We design and implement the power-efficient media access control (MAC) with resource-constraint security in sensors. Then, we evaluate the power efficiency of the S-BAN consisting of small sensors, such as an accessory type ECG and ring-type SpO2. The evaluation of power efficiency of the S-BAN using real sensors convinces us in deploying S-BAN and will also help us in providing feedbacks to the IEEE802.15.6 MAC, which will be the standard for BANs.

  19. Secure Broadcast in Energy-Aware Wireless Sensor Networks

    National Research Council Canada - National Science Library

    Lazos, Loukas; Poovendran, Radha

    2002-01-01

    .... The authors show that existing efficient key distribution techniques for wired networks that rely on logical hierarchies are extremely energy inefficient for energy-constrained wireless ad-hoc networks...

  20. 802.11 Wireless Networks The Definitive Guide

    CERN Document Server

    Gast, Matthew S

    2005-01-01

    As we all know by now, wireless networks offer many advantages over fixed (or wired) networks. Foremost on that list is mobility, since going wireless frees you from the tether of an Ethernet cable at a desk. But that's just the tip of the cable-free iceberg. Wireless networks are also more flexible, faster and easier for you to use, and more affordable to deploy and maintain. The de facto standard for wireless networking is the 802.11 protocol, which includes Wi-Fi (the wireless standard known as 802.11b) and its faster cousin, 802.11g. With easy-to-install 802.11 network hardware avail

  1. A Game Theoretic Framework for Bandwidth Allocation and Pricing in Federated Wireless Networks

    Science.gov (United States)

    Gu, Bo; Yamori, Kyoko; Xu, Sugang; Tanaka, Yoshiaki

    With the proliferation of IEEE 802.11 wireless local area networks, large numbers of wireless access points have been deployed, and it is often the case that a user can detect several access points simultaneously in dense metropolitan areas. Most owners, however, encrypt their networks to prevent the public from accessing them due to the increased traffic and security risk. In this work, we use pricing as an incentive mechanism to motivate the owners to share their networks with the public, while at the same time satisfying users' service demand. Specifically, we propose a “federated network” concept, in which radio resources of various wireless local area networks are managed together. Our algorithm identifies two candidate access points with the lowest price being offered (if available) to each user. We then model the price announcements of access points as a game, and characterize the Nash Equilibrium of the system. The efficiency of the Nash Equilibrium solution is evaluated via simulation studies as well.

  2. WirelessHART vs. ISA100.11a: The Format War Hits the Factory Floor

    OpenAIRE

    Petersen, Stig; Carlsen, Simon

    2011-01-01

    The first decade of the new millennium has been a stage for the rapid development of wireless communication technologies for low-cost, low-power wireless solutions capable of robust and reliable communication [1]. IEEE Standard 802.15.4 for low-rate wireless personal area networks (WPANs) [2] has been the enabling technology for numerous applications within the field of wireless sensor networks (WSNs) [3], and more recently, wireless instrumentation. Although WSNs quickly found their way into...

  3. Delay efficient cooperation in public safety vehicular networks using LTE and IEEE 802.11p

    KAUST Repository

    Atat, Rachad

    2012-01-01

    Cooperative schemes for critical content distribution over vehicular networks are presented and analyzed. The first scheme is based on unicasting from the base station, whereas the second is based on threshold based multicasting. Long Term Evolution (LTE) is used for long range communications with the base station (BS) and 802.11p is considered for inter-vehicle collaboration on the short range. A high mobility environment with correlated shadowing is adopted. Both schemes are shown to outperform non-cooperative unicasting and multicasting, respectively, when the appropriate 802.11p power class is used. The first scheme achieves the best performance among the compared methods, and a practical approximation of that scheme is shown to be close to optimal performance. © 2012 IEEE.

  4. Existing PON Infrastructure Supported Hybrid Fiber-Wireless Sensor Networks

    DEFF Research Database (Denmark)

    Yu, Xianbin; Zhao, Ying; Deng, Lei

    2012-01-01

    We propose a hybrid fiber wireless sensor network based on the existing PON infrastructure. The feasibility of remote sensing and PON convergence is experimentally proven by transmitting direct-sequence spread-spectrum wireless sensing and 2.5Gbps GPON signals.......We propose a hybrid fiber wireless sensor network based on the existing PON infrastructure. The feasibility of remote sensing and PON convergence is experimentally proven by transmitting direct-sequence spread-spectrum wireless sensing and 2.5Gbps GPON signals....

  5. Hybrid RRM Architecture for Future Wireless Networks

    DEFF Research Database (Denmark)

    Tragos, Elias; Mihovska, Albena D.; Mino, Emilio

    2007-01-01

    The concept of ubiquitous and scalable system is applied in the IST WINNER II [1] project to deliver optimum performance for different deployment scenarios from local area to wide area wireless networks. The integration of cellular and local area networks in a unique radio system will provide...... a great advantage to final users and operators, compared with the nowadays situation with many disconnected systems and users equipped with different subscriptions, radio interfaces and terminals. To this issue, the IST project WINNER II has defined three system modes suited to local, metropolitan...... and wide area respectively. The aim of this paper is twofold: first, it presents an architectural solution for scalable and hybrid radio resource management to efficiently integrate the different WINNER modes; second, it proposes a hybrid handover mechanism to exploit the availability of the different...

  6. Network Coding for Wireless Cooperative Networks

    DEFF Research Database (Denmark)

    Khamfroush, Hana; Roetter, Daniel Enrique Lucani; Barros, João

    2014-01-01

    We consider the problem of finding an optimal packet transmission policy that minimizes the total cost of transmitting M data packets from a source S to two receivers R1,R2 over half-duplex, erasure channels. The source can either broadcast random linear network coding (RLNC) packets to the recei......We consider the problem of finding an optimal packet transmission policy that minimizes the total cost of transmitting M data packets from a source S to two receivers R1,R2 over half-duplex, erasure channels. The source can either broadcast random linear network coding (RLNC) packets...... to the receivers or transmit using unicast sessions at each time slot. We assume that the receivers can share their knowledge with each other by sending RLNC packets using unicast transmissions. We model this problem by using a Markov Decision Process (MDP), where the actions include the source of and type...

  7. SDN Based User-Centric Framework for Heterogeneous Wireless Networks

    Directory of Open Access Journals (Sweden)

    Zhaoming Lu

    2016-01-01

    Full Text Available Due to the rapid growth of mobile data traffic, more and more basestations and access points (APs have been densely deployed to provide users with ubiquitous network access, which make current wireless network a complex heterogeneous network (HetNet. However, traditional wireless networks are designed with network-centric approaches where different networks have different quality of service (QoS strategies and cannot easily cooperate with each other to serve network users. Massive network infrastructures could not assure users perceived network and service quality, which is an indisputable fact. To address this issue, we design a new framework for heterogeneous wireless networks with the principle of user-centricity, refactoring the network from users’ perspective to suffice their requirements and preferences. Different from network-centric approaches, the proposed framework takes advantage of Software Defined Networking (SDN and virtualization technology, which will bring better perceived services quality for wireless network users. In the proposed user-centric framework, control plane and data plane are decoupled to manage the HetNets in a flexible and coadjutant way, and resource virtualization technology is introduced to abstract physical resources of HetNets into unified virtualized resources. Hence, ubiquitous and undifferentiated network connectivity and QoE (quality of experience driven fine-grained resource management could be achieved for wireless network users.

  8. One Kind of Routing Algorithm Modified in Wireless Sensor Network

    Directory of Open Access Journals (Sweden)

    Wei Ni Ni

    2016-01-01

    Full Text Available The wireless sensor networks are the emerging next generation sensor networks, Routing technology is the wireless sensor network communication layer of the core technology. To build reliable paths in wireless sensor networks, we can consider two ways: providing multiple paths utilizing the redundancy to assure the communication reliability or constructing transmission reliability mechanism to assure the reliability of every hop. Braid multipath algorithm and ReInforM routing algorithm are the realizations of these two mechanisms. After the analysis of these two algorithms, this paper proposes a ReInforM routing algorithm based braid multipath routing algorithm.

  9. Capacity analysis of wireless mesh networks | Gumel | Nigerian ...

    African Journals Online (AJOL)

    ... number of nodes (n) in a linear topology. The degradation is found to be higher in a fully mesh network as a result of increase in interference and MAC layer contention in the network. Key words: Wireless mesh network (WMN), Adhoc network, Network capacity analysis, Bottleneck collision domain, Medium access control ...

  10. Fundamental Properties of Wireless Mobile Ad-hoc Networks

    NARCIS (Netherlands)

    Hekmat, R.

    2005-01-01

    Wireless mobile ad-hoc networks are formed by mobile devices that set up a possibly short-lived network for communication needs of the moment. Ad-hoc networks are decentralized, self-organizing networks capable of forming a communication network without relying on any fixed infrastructure. Each node

  11. Body area networks using IEEE 802156 implementing the ultra wide band physical layer

    CERN Document Server

    Hernandez, Marco; Mucchi, Lorenzo

    2014-01-01

    The market of wearable wireless medical sensors is experiencing a rapid growth and the associated telecommunications services for the healthcare sector are forecast to further increase in the next years. Medical body area networks (MBANs) allow the mobility of patients and medical personnel by facilitating the remote monitoring of patients suffering from chronic or risky diseases. Currently, MBANs are being introduced in unlicensed frequency bands, where the risk of mutual interference with other electronic devices radiating in the same band can be high. Thus, coexistence is an issue on which

  12. Optimal Channel Width Adaptation, Logical Topology Design, and Routing in Wireless Mesh Networks

    Directory of Open Access Journals (Sweden)

    Li Li

    2009-01-01

    Full Text Available Radio frequency spectrum is a finite and scarce resource. How to efficiently use the spectrum resource is one of the fundamental issues for multi-radio multi-channel wireless mesh networks. However, past research efforts that attempt to exploit multiple channels always assume channels of fixed predetermined width, which prohibits the further effective use of the spectrum resource. In this paper, we address how to optimally adapt channel width to more efficiently utilize the spectrum in IEEE802.11-based multi-radio multi-channel mesh networks. We mathematically formulate the channel width adaptation, logical topology design, and routing as a joint mixed 0-1 integer linear optimization problem, and we also propose our heuristic assignment algorithm. Simulation results show that our method can significantly improve spectrum use efficiency and network performance.

  13. MAC-layer protocol for TCP fairness in Wireless Mesh Networks

    KAUST Repository

    Nawab, Faisal

    2012-08-01

    In this paper we study the interactions of TCP and IEEE 802.11 MAC in Wireless Mesh Networks (WMNs). We use a Markov chain to capture the behavior of TCP sessions, particularly the impact on network throughput performance due to the effect of queue utilization and packet relaying. A closed form solution is derived to numerically determine the throughput. Based on the developed model, we propose a distributed MAC protocol to alleviate the unfairness problem in WMNs. Our protocol uses the age of packet as a priority metric for packet scheduling. Simulation is conducted to validate our model and to illustrate the fairness characteristics of our proposed MAC protocol. We conclude that we can achieve fairness with only little impact on network capacity.

  14. A Nodes Deployment Algorithm in Wireless Sensor Network Based on Distribution

    Directory of Open Access Journals (Sweden)

    Song Yuli

    2014-07-01

    Full Text Available Wireless sensor network coverage is a basic problem of wireless sensor network. In this paper, we propose a wireless sensor network node deployment algorithm base on distribution in order to form an efficient wireless sensor network. The iteratively greedy algorithm is used in this paper to choose priority nodes into active until the entire network is covered by wireless sensor nodes, the whole network to multiply connected. The simulation results show that the distributed wireless sensor network node deployment algorithm can form a multiply connected wireless sensor network.

  15. Mobility Models for Next Generation Wireless Networks Ad Hoc, Vehicular and Mesh Networks

    CERN Document Server

    Santi, Paolo

    2012-01-01

    Mobility Models for Next Generation Wireless Networks: Ad Hoc, Vehicular and Mesh Networks provides the reader with an overview of mobility modelling, encompassing both theoretical and practical aspects related to the challenging mobility modelling task. It also: Provides up-to-date coverage of mobility models for next generation wireless networksOffers an in-depth discussion of the most representative mobility models for major next generation wireless network application scenarios, including WLAN/mesh networks, vehicular networks, wireless sensor networks, and

  16. Low-cost RAU with Optical Power Supply Used in a Hybrid RoF IEEE 802.11 Network

    Science.gov (United States)

    Kowalczyk, M.; Siuzdak, J.

    2014-09-01

    The paper presents design and implementation of a low-cost RAU (Remote Antenna Unit) device. It was designed to work in a hybrid Wi-Fi/optical network based on the IEEE 802.11b/g standard. An unique feature of the device is the possibility of optical power supply.

  17. Performance Evaluation of Multi-Channel Wireless Mesh Networks with Embedded Systems

    Directory of Open Access Journals (Sweden)

    Whye Kit Tan

    2012-01-01

    Full Text Available Many commercial wireless mesh network (WMN products are available in the marketplace with their own proprietary standards, but interoperability among the different vendors is not possible. Open source communities have their own WMN implementation in accordance with the IEEE 802.11s draft standard, Linux open80211s project and FreeBSD WMN implementation. While some studies have focused on the test bed of WMNs based on the open80211s project, none are based on the FreeBSD. In this paper, we built an embedded system using the FreeBSD WMN implementation that utilizes two channels and evaluated its performance. This implementation allows the legacy system to connect to the WMN independent of the type of platform and distributes the load between the two non-overlapping channels. One channel is used for the backhaul connection and the other one is used to connect to the stations to wireless mesh network. By using the power efficient 802.11 technology, this device can also be used as a gateway for the wireless sensor network (WSN.

  18. Performance evaluation of multi-channel wireless mesh networks with embedded systems.

    Science.gov (United States)

    Lam, Jun Huy; Lee, Sang-Gon; Tan, Whye Kit

    2012-01-01

    Many commercial wireless mesh network (WMN) products are available in the marketplace with their own proprietary standards, but interoperability among the different vendors is not possible. Open source communities have their own WMN implementation in accordance with the IEEE 802.11s draft standard, Linux open80211s project and FreeBSD WMN implementation. While some studies have focused on the test bed of WMNs based on the open80211s project, none are based on the FreeBSD. In this paper, we built an embedded system using the FreeBSD WMN implementation that utilizes two channels and evaluated its performance. This implementation allows the legacy system to connect to the WMN independent of the type of platform and distributes the load between the two non-overlapping channels. One channel is used for the backhaul connection and the other one is used to connect to the stations to wireless mesh network. By using the power efficient 802.11 technology, this device can also be used as a gateway for the wireless sensor network (WSN).

  19. An Optimal Method to Design Wireless Sensor Network Structures

    Directory of Open Access Journals (Sweden)

    Yang Ling

    2018-01-01

    Full Text Available In order to optimize the structure of wireless sensor network, an improved wireless sensor network sleep mechanism is proposed. First, some nodes in the area with too high redundancy are dormant by density control, so that the active nodes are even more distributed. Then, the active node is subjected to circular coverage redundancy decision. Different circumferential coverage decision methods are used for network boundary nodes and non-boundary nodes. As a result, the boundary nodes and non-boundary nodes are well dormant, and the network redundancy is reduced. The simulation results show that the improved dormancy mechanism makes the number of active nodes in the network smaller and more evenly, and the network lifetime is extended on the basis of maintaining the original coverage of the network. Therefore, the proposed method can achieve optimal coverage in wireless sensor networks. The network prolongs network lifetime while ensuring reliable monitoring performance.

  20. An 802.11 n wireless local area network transmission scheme for wireless telemedicine applications.

    Science.gov (United States)

    Lin, C F; Hung, S I; Chiang, I H

    2010-10-01

    In this paper, an 802.11 n transmission scheme is proposed for wireless telemedicine applications. IEEE 802.11n standards, a power assignment strategy, space-time block coding (STBC), and an object composition Petri net (OCPN) model are adopted. With the proposed wireless system, G.729 audio bit streams, Joint Photographic Experts Group 2000 (JPEG 2000) clinical images, and Moving Picture Experts Group 4 (MPEG-4) video bit streams achieve a transmission bit error rate (BER) of 10-7, 10-4, and 103 simultaneously. The proposed system meets the requirements prescribed for wireless telemedicine applications. An essential feature of this proposed transmission scheme is that clinical information that requires a high quality of service (QoS) is transmitted at a high power transmission rate with significant error protection. For maximizing resource utilization and minimizing the total transmission power, STBC and adaptive modulation techniques are used in the proposed 802.11 n wireless telemedicine system. Further, low power, direct mapping (DM), low-error protection scheme, and high-level modulation are adopted for messages that can tolerate a high BER. With the proposed transmission scheme, the required reliability of communication can be achieved. Our simulation results have shown that the proposed 802.11 n transmission scheme can be used for developing effective wireless telemedicine systems.

  1. Politecast - a new communication primitive for wireless sensor networks

    OpenAIRE

    Lundén, Marcus

    2010-01-01

    Wireless sensor networks have the potential for becoming a huge market. Ericsson predicts 50 billion devices interconnected to the Internet by the year 2020. Before that, the devices must be made to be able to withstand years of usage without having to change power source as that would be too costly. These devices are typically small, inexpensive and severally resource constrained. Communication is mainly wireless, and the wireless transceiver on the node is typically the most power hungry co...

  2. Energy management in wireless cellular and ad-hoc networks

    CERN Document Server

    Imran, Muhammad; Qaraqe, Khalid; Alouini, Mohamed-Slim; Vasilakos, Athanasios

    2016-01-01

    This book investigates energy management approaches for energy efficient or energy-centric system design and architecture and presents end-to-end energy management in the recent heterogeneous-type wireless network medium. It also considers energy management in wireless sensor and mesh networks by exploiting energy efficient transmission techniques and protocols. and explores energy management in emerging applications, services and engineering to be facilitated with 5G networks such as WBANs, VANETS and Cognitive networks. A special focus of the book is on the examination of the energy management practices in emerging wireless cellular and ad hoc networks. Considering the broad scope of energy management in wireless cellular and ad hoc networks, this book is organized into six sections covering range of Energy efficient systems and architectures; Energy efficient transmission and techniques; Energy efficient applications and services. .

  3. Network preservation through a topology control algorithm for wireless mesh networks

    CSIR Research Space (South Africa)

    Aron, FO

    2008-09-01

    Full Text Available Wireless mesh networks (WMNs) is becoming a promising new technology for extending coverage to farflung rural areas. This it achieves by linking the various wireless LANS (WLANs) in distant locations thus providing a vital mode complimentary...

  4. Simulasi Kinerja Jaringan Nirkabel IEEE-802.11a dan IEEE-802.11g Menggunakan NS-2

    Directory of Open Access Journals (Sweden)

    Helm Fitriawan

    2014-03-01

    Full Text Available Wireless network uses transmission media based on radio waves. This type of networks is mainly useddue to its efficiency and mobility in data exchanging. This paper reports the modeling and simulation of wirelessnetworks based on Cisco Aironet 1130ag access point devices with IEEE 802.11a and IEEE 802.11g standards. Themodeling and simulation are performed using network simulator version 2 (NS-2 that is installed on operationsystem Linux Ubuntu v.10.10. The NS-2 is commonly used and works well in numerous types of network simulation. From simulation, we obtain quality of service parameters by employing several simulation scenarios in terms ofnumber of nodes, distances, and packet data sizes. It can be concluded from simulation results that the IEEE 802.11gnetworks transfer data with better quality than those of IEEE 802.11a networks.  Furthermore, the IEEE 802.11gnetworks provide a higher throughput, with smaller amount of delay and packet loss percentage compared to thoseof IEEE 802.11a networks.

  5. Multipath Routing in Wireless Sensor Networks: Survey and Research Challenges

    Science.gov (United States)

    Radi, Marjan; Dezfouli, Behnam; Bakar, Kamalrulnizam Abu; Lee, Malrey

    2012-01-01

    A wireless sensor network is a large collection of sensor nodes with limited power supply and constrained computational capability. Due to the restricted communication range and high density of sensor nodes, packet forwarding in sensor networks is usually performed through multi-hop data transmission. Therefore, routing in wireless sensor networks has been considered an important field of research over the past decade. Nowadays, multipath routing approach is widely used in wireless sensor networks to improve network performance through efficient utilization of available network resources. Accordingly, the main aim of this survey is to present the concept of the multipath routing approach and its fundamental challenges, as well as the basic motivations for utilizing this technique in wireless sensor networks. In addition, we present a comprehensive taxonomy on the existing multipath routing protocols, which are especially designed for wireless sensor networks. We highlight the primary motivation behind the development of each protocol category and explain the operation of different protocols in detail, with emphasis on their advantages and disadvantages. Furthermore, this paper compares and summarizes the state-of-the-art multipath routing techniques from the network application point of view. Finally, we identify open issues for further research in the development of multipath routing protocols for wireless sensor networks. PMID:22368490

  6. Multipath routing in wireless sensor networks: survey and research challenges.

    Science.gov (United States)

    Radi, Marjan; Dezfouli, Behnam; Abu Bakar, Kamalrulnizam; Lee, Malrey

    2012-01-01

    A wireless sensor network is a large collection of sensor nodes with limited power supply and constrained computational capability. Due to the restricted communication range and high density of sensor nodes, packet forwarding in sensor networks is usually performed through multi-hop data transmission. Therefore, routing in wireless sensor networks has been considered an important field of research over the past decade. Nowadays, multipath routing approach is widely used in wireless sensor networks to improve network performance through efficient utilization of available network resources. Accordingly, the main aim of this survey is to present the concept of the multipath routing approach and its fundamental challenges, as well as the basic motivations for utilizing this technique in wireless sensor networks. In addition, we present a comprehensive taxonomy on the existing multipath routing protocols, which are especially designed for wireless sensor networks. We highlight the primary motivation behind the development of each protocol category and explain the operation of different protocols in detail, with emphasis on their advantages and disadvantages. Furthermore, this paper compares and summarizes the state-of-the-art multipath routing techniques from the network application point of view. Finally, we identify open issues for further research in the development of multipath routing protocols for wireless sensor networks.

  7. Handbook of sensor networks compact wireless and wired sensing systems

    CERN Document Server

    Ilyas, Mohammad

    2004-01-01

    INTRODUCTION Opportunities and Challenges in Wireless Sensor Networks, M. Haenggi, Next Generation Technologies to Enable Sensor Networks, J. I.  Goodman, A. I. Reuther, and D. R. Martinez Sensor Networks Management, L. B. Ruiz, J. M. Nogueira, and A. A. F. Loureiro Models for Programmability in Sensor Networks, A. Boulis Miniaturizing Sensor Networks with MEMS, Brett Warneke A Taxonomy of Routing Techniques in Wireless Sensor Networks, J. N. Al-Karaki and A. E. Kamal Artificial Perceptual Systems, A. Loutfi, M. Lindquist, and P. Wide APPLICATIONS Sensor Network Architecture and Appl

  8. An Open and Modular Hardware Node for Wireless Sensor and Body Area Networks

    Directory of Open Access Journals (Sweden)

    L. Ciabattoni

    2016-01-01

    Full Text Available Health monitoring is nowadays one of the hottest markets due to the increasing interest in prevention and treatment of physical problems. In this context the development of wearable, wireless, open-source, and nonintrusive sensing solutions is still an open problem. Indeed, most of the existing commercial architectures are closed and provide little flexibility. In this paper, an open hardware architecture for designing a modular wireless sensor node for health monitoring is proposed. By separating the connection and sensing functions in two separate boards, compliant with the IEEE1451 standard, we add plug and play capabilities to analog transducers, while granting at the same time a high level of customization. As an additional contribution of the work, we developed a cosimulation tool which simplifies the physical connection with the hardware devices and provides support for complex systems. Finally, a wireless body area network for fall detection and health monitoring, based on wireless node prototypes realized according to the proposed architecture, is presented as an application scenario.

  9. Reliable Wireless Broadcast with Linear Network Coding for Multipoint-to-Multipoint Real-Time Communications

    Science.gov (United States)

    Kondo, Yoshihisa; Yomo, Hiroyuki; Yamaguchi, Shinji; Davis, Peter; Miura, Ryu; Obana, Sadao; Sampei, Seiichi

    This paper proposes multipoint-to-multipoint (MPtoMP) real-time broadcast transmission using network coding for ad-hoc networks like video game networks. We aim to achieve highly reliable MPtoMP broadcasting using IEEE 802.11 media access control (MAC) that does not include a retransmission mechanism. When each node detects packets from the other nodes in a sequence, the correctly detected packets are network-encoded, and the encoded packet is broadcasted in the next sequence as a piggy-back for its native packet. To prevent increase of overhead in each packet due to piggy-back packet transmission, network coding vector for each node is exchanged between all nodes in the negotiation phase. Each user keeps using the same coding vector generated in the negotiation phase, and only coding information that represents which user signal is included in the network coding process is transmitted along with the piggy-back packet. Our simulation results show that the proposed method can provide higher reliability than other schemes using multi point relay (MPR) or redundant transmissions such as forward error correction (FEC). We also implement the proposed method in a wireless testbed, and show that the proposed method achieves high reliability in a real-world environment with a practical degree of complexity when installed on current wireless devices.

  10. On the network convergence process in RPL over IEEE 802.15.4 multihop networks: improvement and trade-offs.

    Science.gov (United States)

    Kermajani, Hamidreza; Gomez, Carles

    2014-07-07

    The IPv6 Routing Protocol for Low-power and Lossy Networks (RPL) has been recently developed by the Internet Engineering Task Force (IETF). Given its crucial role in enabling the Internet of Things, a significant amount of research effort has already been devoted to RPL. However, the RPL network convergence process has not yet been investigated in detail. In this paper we study the influence of the main RPL parameters and mechanisms on the network convergence process of this protocol in IEEE 802.15.4 multihop networks. We also propose and evaluate a mechanism that leverages an option available in RPL for accelerating the network convergence process. We carry out extensive simulations for a wide range of conditions, considering different network scenarios in terms of size and density. Results show that network convergence performance depends dramatically on the use and adequate configuration of key RPL parameters and mechanisms. The findings and contributions of this work provide a RPL configuration guideline for network convergence performance tuning, as well as a characterization of the related performance trade-offs.

  11. On the Network Convergence Process in RPL over IEEE 802.15.4 Multihop Networks: Improvement and Trade-Offs

    Directory of Open Access Journals (Sweden)

    Hamidreza Kermajani

    2014-07-01

    Full Text Available The IPv6 Routing Protocol for Low-power and Lossy Networks (RPL has been recently developed by the Internet Engineering Task Force (IETF. Given its crucial role in enabling the Internet of Things, a significant amount of research effort has already been devoted to RPL. However, the RPL network convergence process has not yet been investigated in detail. In this paper we study the influence of the main RPL parameters and mechanisms on the network convergence process of this protocol in IEEE 802.15.4 multihop networks. We also propose and evaluate a mechanism that leverages an option available in RPL for accelerating the network convergence process. We carry out extensive simulations for a wide range of conditions, considering different network scenarios in terms of size and density. Results show that network convergence performance depends dramatically on the use and adequate configuration of key RPL parameters and mechanisms. The findings and contributions of this work provide a RPL configuration guideline for network convergence performance tuning, as well as a characterization of the related performance trade-offs.

  12. A survey on the wireless sensor network technology

    International Nuclear Information System (INIS)

    Kim, Jae Hee; Jun, Hyeong Seop; Lee, Jae Cheol; Choi, Yoo Rak

    2007-12-01

    Wireless sensor technology is required in the safety inspection for safety-critical unit of nuclear power plant. This report describes wireless sensor technology related with the project named 'Development of a remote care system of NPP components based on the network and safety database'. This report includes contents of methodology and status of sensor network construction, status of zigbee sensor network, problem of security and sensor battery. Energy harvesting technology will be mentioned on the next report

  13. A Study on Wireless Charging for Prolonging the Lifetime of Wireless Sensor Networks

    Directory of Open Access Journals (Sweden)

    Weijian Tu

    2017-07-01

    Full Text Available Wireless charging is an important issue in wireless sensor networks, since it can provide an emerging and effective solution in the absence of other power supplies. The state-of-the-art methods employ a mobile car and a predefined moving path to charge the sensor nodes in the network. Previous studies only consider a factor of the network (i.e., residual energy of sensor node as a constraint to design the wireless charging strategy. However, other factors, such as the travelled distance of the mobile car, can also affect the effectiveness of wireless charging strategy. In this work, we study wireless charging strategy based on the analysis of a combination of two factors, including the residual energy of sensor nodes and the travelled distance of the charging car. Firstly, we theoretically analyze the limited size of the sensor network to match the capability of a charging car. Then, the networked factors are selected as the weights of traveling salesman problem (TSP to design the moving path of the charging car. Thirdly, the charging time of each sensor node is computed based on the linear programming problem for the charging car. Finally, a charging period for the network is studied. The experimental results show that the proposed approach can significantly maximize the lifetime of the wireless sensor network.

  14. A Study on Wireless Charging for Prolonging the Lifetime of Wireless Sensor Networks.

    Science.gov (United States)

    Tu, Weijian; Xu, Xianghua; Ye, Tingcong; Cheng, Zongmao

    2017-07-04

    Wireless charging is an important issue in wireless sensor networks, since it can provide an emerging and effective solution in the absence of other power supplies. The state-of-the-art methods employ a mobile car and a predefined moving path to charge the sensor nodes in the network. Previous studies only consider a factor of the network (i.e., residual energy of sensor node) as a constraint to design the wireless charging strategy. However, other factors, such as the travelled distance of the mobile car, can also affect the effectiveness of wireless charging strategy. In this work, we study wireless charging strategy based on the analysis of a combination of two factors, including the residual energy of sensor nodes and the travelled distance of the charging car. Firstly, we theoretically analyze the limited size of the sensor network to match the capability of a charging car. Then, the networked factors are selected as the weights of traveling salesman problem (TSP) to design the moving path of the charging car. Thirdly, the charging time of each sensor node is computed based on the linear programming problem for the charging car. Finally, a charging period for the network is studied. The experimental results show that the proposed approach can significantly maximize the lifetime of the wireless sensor network.

  15. Protocol design and analysis for cooperative wireless networks

    CERN Document Server

    Song, Wei; Jin, A-Long

    2017-01-01

    This book focuses on the design and analysis of protocols for cooperative wireless networks, especially at the medium access control (MAC) layer and for crosslayer design between the MAC layer and the physical layer. It highlights two main points that are often neglected in other books: energy-efficiency and spatial random distribution of wireless devices. Effective methods in stochastic geometry for the design and analysis of wireless networks are also explored. After providing a comprehensive review of existing studies in the literature, the authors point out the challenges that are worth further investigation. Then, they introduce several novel solutions for cooperative wireless network protocols that reduce energy consumption and address spatial random distribution of wireless nodes. For each solution, the book offers a clear system model and problem formulation, details of the proposed cooperative schemes, comprehensive performance analysis, and extensive numerical and simulation results that validate th...

  16. Development of a Testbed for Wireless Underground Sensor Networks

    Directory of Open Access Journals (Sweden)

    Mehmet C. Vuran

    2010-01-01

    Full Text Available Wireless Underground Sensor Networks (WUSNs constitute one of the promising application areas of the recently developed wireless sensor networking techniques. WUSN is a specialized kind of Wireless Sensor Network (WSN that mainly focuses on the use of sensors that communicate through soil. Recent models for the wireless underground communication channel are proposed but few field experiments were realized to verify the accuracy of the models. The realization of field WUSN experiments proved to be extremely complex and time-consuming in comparison with the traditional wireless environment. To the best of our knowledge, this is the first work that proposes guidelines for the development of an outdoor WUSN testbed with the goals of improving the accuracy and reducing of time for WUSN experiments. Although the work mainly aims WUSNs, many of the presented practices can also be applied to generic WSN testbeds.

  17. 2014 International Conference on Wireless Communications, Networking and Applications

    CERN Document Server

    2016-01-01

    This book is based on a series of conferences on Wireless Communications, Networking and Applications that have been held on December 27-28, 2014 in Shenzhen, China. The meetings themselves were a response to technological developments in the areas of wireless communications, networking and applications and facilitate researchers, engineers and students to share the latest research results and the advanced research methods of the field. The broad variety of disciplines involved in this research and the differences in approaching the basic problems are probably typical of a developing field of interdisciplinary research. However, some main areas of research and development in the emerging areas of wireless communication technology can now be identified. The contributions to this book are mainly selected from the papers of the conference on wireless communications, networking and applications and reflect the main areas of interest: Section 1 - Emerging Topics in Wireless and Mobile Computing and Communications...

  18. Increased Efficiency of Face Recognition System using Wireless Sensor Network

    Directory of Open Access Journals (Sweden)

    Rajani Muraleedharan

    2006-02-01

    Full Text Available This research was inspired by the need of a flexible and cost effective biometric security system. The flexibility of the wireless sensor network makes it a natural choice for data transmission. Swarm intelligence (SI is used to optimize routing in distributed time varying network. In this paper, SI maintains the required bit error rate (BER for varied channel conditions while consuming minimal energy. A specific biometric, the face recognition system, is discussed as an example. Simulation shows that the wireless sensor network is efficient in energy consumption while keeping the transmission accuracy, and the wireless face recognition system is competitive to the traditional wired face recognition system in classification accuracy.

  19. Wireless Sensor Network for Forest Fire Detection

    Directory of Open Access Journals (Sweden)

    Emansa Hasri Putra

    2013-09-01

    Full Text Available Forest fires are one of problems that threaten sustainability of the forest. Early prevention system for indications of forest fires is absolutely necessary. The extent of the forest to be one of the problems encountered in the forest condition monitoring. To overcome the problems of forest extent, designed a system of forest fire detection system by adopting the Wireless Sensor Network (WSN using multiple sensor nodes. Each sensor node has a microcontroller, transmitter/receiver and three sensors. Measurement method is performed by measuring the temperature, flame, the levels of methane, hydrocarbons, and CO2 in some forest area and the combustion of peat in a simulator. From results of measurements of temperature, levels of methane, a hydrocarbon gas and CO2 in an open area indicates there are no signs of fires due to the value of the temperature, methane, hydrocarbon gas, and CO2 is below the measurement in the space simulator.

  20. Spectral efficiency enhancement with interference cancellation for wireless relay network

    DEFF Research Database (Denmark)

    Yomo, Hiroyuki; De Carvalho, Elisabeth

    The introduction of relaying into wireless communication system for coverage enhancement can cause severe decrease of spectral efficiency due to the requirement on extra radio resource. In this paper, we propose a method to increase spectral efficiency in such a wireless relay network by employin...

  1. Design issues and applications of wireless sensor networks ...

    African Journals Online (AJOL)

    ... using tiny wireless sensor motes known as “smart dusts”, which have been made possible by advances in micro-electromechanical systems (MEMS) technology, wireless communications and digital electronics. Design considerations for the hardware and the topology necessary to realize these networks were evaluated.

  2. Effect of mobility models on infrastructure based wireless networks ...

    African Journals Online (AJOL)

    The tremendous demand is pushing the development of wireless mobile communications faster than ever before. Handoff management has widely been recognized as one of the most important and challenging problems for a seamless access to wireless network and mobile services. Mobility Models plays an important ...

  3. Reliable and Congestion Control Protocols for Wireless Sensor Networks

    Directory of Open Access Journals (Sweden)

    Kirti Kharb

    2016-01-01

    Full Text Available The objective of this paper is to analyze review and different congestion control protocols that are employed at the transport layer and some of them working at the medium access control layer in wireless sensor networks. Firstly, a brief introduction is given about wireless sensor networks and how congestion occurs in such networks. Secondly, the concept of congestion is discussed. Thirdly, the reason of occurrence of congestion in wireless sensor networks is analyzed. After that, congestion control and why it is needed in the wireless sensor networks is discussed. Then, a brief review of different congestion control and reliable data transport mechanisms are discussed. Finally, a comparative analysis of different protocols is made depending on their performance on various parameters such as - traffic direction, energy conservation characteristic, efficiency etc. and the paper is concluded.

  4. Overlapping coalition formation games in wireless communication networks

    CERN Document Server

    Wang, Tianyu; Saad, Walid; Han, Zhu

    2017-01-01

    This brief introduces overlapping coalition formation games (OCF games), a novel mathematical framework from cooperative game theory that can be used to model, design and analyze cooperative scenarios in future wireless communication networks. The concepts of OCF games are explained, and several algorithmic aspects are studied. In addition, several major application scenarios are discussed. These applications are drawn from a variety of fields that include radio resource allocation in dense wireless networks, cooperative spectrum sensing for cognitive radio networks, and resource management for crowd sourcing. For each application, the use of OCF games is discussed in detail in order to show how this framework can be used to solve relevant wireless networking problems. Overlapping Coalition Formation Games in Wireless Communication Networks provides researchers, students and practitioners with a concise overview of existing works in this emerging area, exploring the relevant fundamental theories, key techniqu...

  5. Trust framework for a secured routing in wireless sensor network

    Directory of Open Access Journals (Sweden)

    Ouassila Hoceini

    2015-11-01

    Full Text Available Traditional techniques to eliminate insider attacks developed for wired and wireless ad hoc networks are not well suited for wireless sensors networks due to their resource constraints nature. In order to protect WSNs against malicious and selfish behavior, some trust-based systems have recently been modeled. The resource efficiency and dependability of a trust system are the most fundamental requirements for any wireless sensor network (WSN. In this paper, we propose a Trust Framework for a Secured Routing in Wireless Sensor Network (TSR scheme, which works with clustered networks. This approach can effectively reduce the cost of trust evaluation and guarantee a better selection of safest paths that lead to the base station. Theoretical as well as simulation results show that our scheme requires less communication overheads and consumes less energy as compared to the current typical trust systems for WSNs. Moreover, it detects selfish and defective nodes and prevents us of insider attacks

  6. Energy Efficient Wireless Sensor Network Modelling Based on Complex Networks

    Directory of Open Access Journals (Sweden)

    Lin Xiao

    2016-01-01

    Full Text Available The power consumption and energy efficiency of wireless sensor network are the significant problems in Internet of Things network. In this paper, we consider the network topology optimization based on complex network theory to solve the energy efficiency problem of WSN. We propose the energy efficient model of WSN according to the basic principle of small world from complex networks. Small world network has clustering features that are similar to that of the rules of the network but also has similarity to random networks of small average path length. It can be utilized to optimize the energy efficiency of the whole network. Optimal number of multiple sink nodes of the WSN topology is proposed for optimizing energy efficiency. Then, the hierarchical clustering analysis is applied to implement this clustering of the sensor nodes and pick up the sink nodes from the sensor nodes as the clustering head. Meanwhile, the update method is proposed to determine the sink node when the death of certain sink node happened which can cause the paralysis of network. Simulation results verify the energy efficiency of the proposed model and validate the updating of the sink nodes to ensure the normal operation of the WSN.

  7. A Novel Spectrally Efficient Asynchronous Multi-Channel MAC Using a Half-Duplex Transceiver for Wireless Networks

    Directory of Open Access Journals (Sweden)

    Abdullah Devendiran

    2018-01-01

    Full Text Available Multi-channel medium access control (MAC protocols maximize network performance by enabling concurrent wireless transmissions over non-interfering channels. Despite physical layer advancements, the underlying IEEE 802.11 MAC standard cannot fully exploit features and support high-performance applications. In this work, we propose the novel spectrally efficient asynchronous multi-channel MAC (SA-MMAC protocol for wireless networks using a single half-duplex transceiver. A full-duplex mode of operation on data channels reduces the signaling overhead and boosts the spectrum efficiency. A revamped contention mechanism of IEEE 802.11 addresses the multi-channel hidden terminal problem, and a jamming signal from the receiver addresses the collisions in control signals. Furthermore, the control channel is used for data transmissions to increase the bandwidth utilization but under a restricted half-duplex mode to avoid causing a bottleneck situation. The simulator is tested for correctness. The results suggest that the protocol can work well on 3, 4, or 12 concurrent channels with high node density, providing about 12.5 times more throughput than IEEE 802.11 and 18% to 95% more throughput than its multi-channel variants under saturated traffic conditions.

  8. Industrial and non-consumer applications of wireless sensor networks

    Science.gov (United States)

    Pentikäinen, Vesa; Heikkilä, Tapio; Määttä, Kalle; Tukeva, Pirkka; Korkalainen, Marko; Saavalainen, Pekka; Kilpeläinen, Pekka

    2008-04-01

    There is a growing potential of applications for wireless monitoring, control and instrumentation in industrial environments, construction sites and agriculture. Wireless communication technologies have clear benefits in harsh environments where traditional cables are too vulnerable or they cannot be installed permanently. Sensor networks with multiple wireless sensor nodes are needed when the size of the monitored area is large and especially in dynamic environments, like construction sites where the sensors can be installed to moving vehicles and work machines. In this paper we present results from some of our developments where short range wireless communication technologies have been applied for industrial and non-consumer monitoring applications.

  9. Interference minimization in physical model of wireless networks

    OpenAIRE

    Aslanyan, Hakob

    2011-01-01

    Interference minimization problem in wireless sensor and ad-hoc networks is considered. That is to assign a transmission power to each node of a network such that the network is connected and at the same time the maximum of accumulated signal straight on network nodes is minimum. Previous works on interference minimization in wireless networks mainly consider the disk graph model of network. For disk graph model two approximation algorithms with $O(\\sqrt{n})$ and $O((opt\\ln{n})^{2})$ upper bo...

  10. Green Frame Aggregation Scheme for IEEE 802.11n Networks

    KAUST Repository

    Alaslani, Maha S.

    2015-04-01

    Frame aggregation is one of the major MAC layer enhancements in the IEEE 802.11 family that boosts the network throughput performance. It aims to achieve higher throughput by transmitting huge amount of data in a single transmit oppor- tunity. With the increasing awareness of energy e ciency, it has become vital to rethink about the design of such frame aggregation protocol. Aggregation techniques help to reduce energy consumption over ideal channel conditions. However, in a noisy channel environment, a new energy-aware frame aggregation scheme is required. In this thesis, a novel Green Frame Aggregation (GFA) scheduling scheme has been proposed and evaluated. GFA optimizes the aggregate size based on channel quality in order to minimize the consumed energy. GFA selects the optimal sub-frame size that satisfies the loss constraint for real-time applications as well as the energy budget of the ideal channel situations. The design, the implementation, and evaluation of GFA using testbed deployment is done. The experimental analysis shows that GFA outperforms the conventional frame aggregation methodology in terms of energy e ciency by about 6⇥ in the presence of severe interference conditions. Moreover, GFA also outperforms the static frame sizing method in terms of network goodput and maintains almost the same end- to-end latency.

  11. Reliability Analysis of Wireless Sensor Networks Using Markovian Model

    Directory of Open Access Journals (Sweden)

    Jin Zhu

    2012-01-01

    Full Text Available This paper investigates reliability analysis of wireless sensor networks whose topology is switching among possible connections which are governed by a Markovian chain. We give the quantized relations between network topology, data acquisition rate, nodes' calculation ability, and network reliability. By applying Lyapunov method, sufficient conditions of network reliability are proposed for such topology switching networks with constant or varying data acquisition rate. With the conditions satisfied, the quantity of data transported over wireless network node will not exceed node capacity such that reliability is ensured. Our theoretical work helps to provide a deeper understanding of real-world wireless sensor networks, which may find its application in the fields of network design and topology control.

  12. Wireless Sensor Networks for Environmental Monitoring

    Science.gov (United States)

    Liang, X.; Liang, Y.; Navarro, M.; Zhong, X.; Villalba, G.; Li, Y.; Davis, T.; Erratt, N.

    2015-12-01

    Wireless sensor networks (WSNs) have gained an increasing interest in a broad range of new scientific research and applications. WSN technologies can provide high resolution for spatial and temporal data which has not been possible before, opening up new opportunities. On the other hand, WSNs, particularly outdoor WSNs in harsh environments, present great challenges for scientists and engineers in terms of the network design, deployment, operation, management, and maintenance. Since 2010, we have been working on the deployment of an outdoor multi-hop WSN testbed for hydrological/environmental monitoring in a forested hill-sloped region at the Audubon Society of Western Pennsylvania (ASWP), Pennsylvania, USA. The ASWP WSN testbed has continuously evolved and had more than 80 nodes by now. To our knowledge, the ASWP WSN testbed represents one of the first known long-term multi-hop WSN deployments in an outdoor environment. As simulation and laboratory methods are unable to capture the complexity of outdoor environments (e.g., forests, oceans, mountains, or glaciers), which significantly affect WSN operations and maintenance, experimental deployments are essential to investigate and understand WSN behaviors and performances as well as its maintenance characteristics under these harsh conditions. In this talk, based on our empirical studies with the ASWP WSN testbed, we will present our discoveries and investigations on several important aspects including WSN energy profile, node reprogramming, network management system, and testbed maintenance. We will then provide our insight into these critical aspects of outdoor WSN deployments and operations.

  13. Wireless Fractal Ultra-Dense Cellular Networks.

    Science.gov (United States)

    Hao, Yixue; Chen, Min; Hu, Long; Song, Jeungeun; Volk, Mojca; Humar, Iztok

    2017-04-12

    With the ever-growing number of mobile devices, there is an explosive expansion in mobile data services. This represents a challenge for the traditional cellular network architecture to cope with the massive wireless traffic generated by mobile media applications. To meet this challenge, research is currently focused on the introduction of a small cell base station (BS) due to its low transmit power consumption and flexibility of deployment. However, due to a complex deployment environment and low transmit power of small cell BSs, the coverage boundary of small cell BSs will not have a traditional regular shape. Therefore, in this paper, we discuss the coverage boundary of an ultra-dense small cell network and give its main features: aeolotropy of path loss fading and fractal coverage boundary. Simple performance analysis is given, including coverage probability and transmission rate, etc., based on stochastic geometry theory and fractal theory. Finally, we present an application scene and discuss challenges in the ultra-dense small cell network.

  14. Multi-Channel Multi-Radio Using 802.11 Based Media Access for Sink Nodes in Wireless Sensor Networks

    Directory of Open Access Journals (Sweden)

    Kok-Keong Loo

    2011-05-01

    Full Text Available The next generation surveillance and multimedia systems will become increasingly deployed as wireless sensor networks in order to monitor parks, public places and for business usage. The convergence of data and telecommunication over IP-based networks has paved the way for wireless networks. Functions are becoming more intertwined by the compelling force of innovation and technology. For example, many closed-circuit TV premises surveillance systems now rely on transmitting their images and data over IP networks instead of standalone video circuits. These systems will increase their reliability in the future on wireless networks and on IEEE 802.11 networks. However, due to limited non-overlapping channels, delay, and congestion there will be problems at sink nodes. In this paper we provide necessary conditions to verify the feasibility of round robin technique in these networks at the sink nodes by using a technique to regulate multi-radio multichannel assignment. We demonstrate through simulations that dynamic channel assignment scheme using multi-radio, and multichannel configuration at a single sink node can perform close to optimal on the average while multiple sink node assignment also performs well. The methods proposed in this paper can be a valuable tool for network designers in planning network deployment and for optimizing different performance objectives.

  15. Multi-channel multi-radio using 802.11 based media access for sink nodes in wireless sensor networks.

    Science.gov (United States)

    Campbell, Carlene E-A; Khan, Shafiullah; Singh, Dhananjay; Loo, Kok-Keong

    2011-01-01

    The next generation surveillance and multimedia systems will become increasingly deployed as wireless sensor networks in order to monitor parks, public places and for business usage. The convergence of data and telecommunication over IP-based networks has paved the way for wireless networks. Functions are becoming more intertwined by the compelling force of innovation and technology. For example, many closed-circuit TV premises surveillance systems now rely on transmitting their images and data over IP networks instead of standalone video circuits. These systems will increase their reliability in the future on wireless networks and on IEEE 802.11 networks. However, due to limited non-overlapping channels, delay, and congestion there will be problems at sink nodes. In this paper we provide necessary conditions to verify the feasibility of round robin technique in these networks at the sink nodes by using a technique to regulate multi-radio multichannel assignment. We demonstrate through simulations that dynamic channel assignment scheme using multi-radio, and multichannel configuration at a single sink node can perform close to optimal on the average while multiple sink node assignment also performs well. The methods proposed in this paper can be a valuable tool for network designers in planning network deployment and for optimizing different performance objectives.

  16. Reconfigurable antenna options for 2.45/5 GHz wireless body area networks in healthcare applications.

    Science.gov (United States)

    Abbas, Syed Muzahir; Ranga, Yogesh; Esselle, Karu P

    2015-01-01

    This paper presents electronically reconfigurable antenna options in healthcare applications. They are suitable for wireless body area network devices operating in the industrial, scientific, and medical (ISM) band at 2.45 GHz and IEEE 802.11 Wireless Local Area Network (WLAN) band at 5 GHz (5.15-5.35 GHz, 5.25-5.35 GHz). Two types of antennas are investigated: Antenna-I has a full ground plane and Antenna-II has a partial ground plane. The proposed antennas provide ISM operation in one mode while in another mode they support 5 GHz WLAN band. Their performance is assessed for body centric wireless communication using a simplified human body model. Antenna sensitivity to the gap between the antenna and the human body is investigated for both modes of each antenna. The proposed antennas exhibit a wide radiation pattern along the body surface to provide wide coverage and their small width (14 mm) makes them suitable for on-body communication in healthcare applications.

  17. Cooperative Content Distribution over Wireless Networks for Energy and Delay Minimization

    KAUST Repository

    Atat, Rachad

    2012-06-01

    Content distribution with mobile-to-mobile cooperation is studied. Data is sent to mobile terminals on a long range link then the terminals exchange the content using an appropriate short range wireless technology. Unicasting and multicasting are investigated, both on the long range and short range links. Energy minimization is formulated as an optimization problem for each scenario, and the optimal solutions are determined in closed form. Moreover, the schemes are applied in public safety vehicular networks, where Long Term Evolution (LTE) network is used for the long range link, while IEEE 802.11 p is considered for inter-vehicle collaboration on the short range links. Finally, relay-based multicasting is applied in high speed trains for energy and delay minimization. Results show that cooperative schemes outperform non-cooperative ones and other previous related work in terms of energy and delay savings. Furthermore, practical implementation aspects of the proposed methods are also discussed.

  18. A Wildlife Monitoring System Based on Wireless Image Sensor Networks

    Directory of Open Access Journals (Sweden)

    Junguo Zhang

    2014-10-01

    Full Text Available Survival and development of wildlife sustains the balance and stability of the entire ecosystem. Wildlife monitoring can provide lots of information such as wildlife species, quantity, habits, quality of life and habitat conditions, to help researchers grasp the status and dynamics of wildlife resources, and to provide basis for the effective protection, sustainable use, and scientific management of wildlife resources. Wildlife monitoring is the foundation of wildlife protection and management. Wireless Sensor Networks (WSN technology has become the most popular technology in the field of information. With advance of the CMOS image sensor technology, wireless sensor networks combined with image sensors, namely Wireless Image Sensor Networks (WISN technology, has emerged as an alternative in monitoring applications. Monitoring wildlife is one of its most promising applications. In this paper, system architecture of the wildlife monitoring system based on the wireless image sensor networks was presented to overcome the shortcomings of the traditional monitoring methods. Specifically, some key issues including design of wireless image sensor nodes and software process design have been studied and presented. A self-powered rotatable wireless infrared image sensor node based on ARM and an aggregation node designed for large amounts of data were developed. In addition, their corresponding software was designed. The proposed system is able to monitor wildlife accurately, automatically, and remotely in all-weather condition, which lays foundations for applications of wireless image sensor networks in wildlife monitoring.

  19. On the Capacity of Hybrid Wireless Networks with Opportunistic Routing

    Directory of Open Access Journals (Sweden)

    Tan Le

    2010-01-01

    Full Text Available This paper studies the capacity of hybrid wireless networks with opportunistic routing (OR. We first extend the opportunistic routing algorithm to exploit high-speed data transmissions in infrastructure network through base stations. We then develop linear programming models to calculate the end-to-end throughput bounds from multiple source nodes to single as well as multiple destination nodes. The developed models are applied to study several hybrid wireless network examples. Through case studies, we investigate several factors that have significant impacts on the hybrid wireless network capacity under opportunistic routing, such as node transmission range, density and distribution pattern of base stations (BTs, and number of wireless channels on wireless nodes and base stations. Our numerical results demonstrate that opportunistic routing could achieve much higher throughput on both ad hoc and hybrid networks than traditional unicast routing (UR. Moreover, opportunistic routing can efficiently utilize base stations and achieve significantly higher throughput gains in hybrid wireless networks than in pure ad hoc networks especially with multiple-channel base stations.

  20. Mobility management techniques for the next-generation wireless networks

    Science.gov (United States)

    Sun, Junzhao; Howie, Douglas P.; Sauvola, Jaakko J.

    2001-10-01

    The tremendous demands from social market are pushing the booming development of mobile communications faster than ever before, leading to plenty of new advanced techniques emerging. With the converging of mobile and wireless communications with Internet services, the boundary between mobile personal telecommunications and wireless computer networks is disappearing. Wireless networks of the next generation need the support of all the advances on new architectures, standards, and protocols. Mobility management is an important issue in the area of mobile communications, which can be best solved at the network layer. One of the key features of the next generation wireless networks is all-IP infrastructure. This paper discusses the mobility management schemes for the next generation mobile networks through extending IP's functions with mobility support. A global hierarchical framework model for the mobility management of wireless networks is presented, in which the mobility management is divided into two complementary tasks: macro mobility and micro mobility. As the macro mobility solution, a basic principle of Mobile IP is introduced, together with the optimal schemes and the advances in IPv6. The disadvantages of the Mobile IP on solving the micro mobility problem are analyzed, on the basis of which three main proposals are discussed as the micro mobility solutions for mobile communications, including Hierarchical Mobile IP (HMIP), Cellular IP, and Handoff-Aware Wireless Access Internet Infrastructure (HAWAII). A unified model is also described in which the different micro mobility solutions can coexist simultaneously in mobile networks.

  1. Performance Evaluation of a Routing Protocol in Wireless Sensor Network

    National Research Council Canada - National Science Library

    Cheng Kiat Amos, Teo

    2005-01-01

    ... and have topologies engineered. As such, recent research into wireless sensor networks has attracted great interest due to its diversity of applications, ranging in areas such as home, health, environmental and military applications...

  2. A General Framework for Flow Control in Wireless Networks

    National Research Council Canada - National Science Library

    Chen, Minghua

    2006-01-01

    .... Current widely accepted solutions assume that congestion is the only cause of packet loss and are not applicable to wireless networks in which the bulk of packet loss is due to errors at the physical layer...

  3. Resource Allocation and Cross Layer Control in Wireless Networks

    National Research Council Canada - National Science Library

    Georgiadis, L; Neely, M; Tassiulas, L

    2006-01-01

    .... In this paper we will present abstract models that capture the cross layer interaction from the physical to transport layer in wireless network architectures including cellular, ad-hoc and sensor...

  4. Energy-Efficient Querying of Wireless Sensor Networks

    National Research Council Canada - National Science Library

    Mann, Christopher R

    2007-01-01

    Due to the distributed nature of information collection in wireless sensor networks and the inherent limitations of the component devices, the ability to store, locate, and retrieve data and services...

  5. Adaptive and Reactive Security for Wireless Sensor Networks

    National Research Council Canada - National Science Library

    Stankovic, John A

    2007-01-01

    .... WSNs are also susceptible to malicious, non-random security attacks. For example, a wireless sensor network deployed in remote regions to detect and classify targets could be rendered inoperative by various security attacks...

  6. Distributed Tracking in Wireless Ad Hoc Sensor Networks

    National Research Council Canada - National Science Library

    Chong, Chee-Yee; Zhao, Feng; Mori, Shozo; Kumar, Sri

    2003-01-01

    Target tracking is an important application for wireless ad hoc sensor networks. Because of the energy and communication constraints imposed by the size of the sensors, the processing has to be distributed over the sensor nodes...

  7. IEEE 802.11 ECG monitoring system.

    Science.gov (United States)

    Tejero-Calado, Juan; Lopez-Casado, Carmen; Bernal-Martin, Antonio; Lopez-Gomez, Miguel; Romero-Romero, Marco; Quesada, Guillermo; Lorca, Julio; Rivas, Ramon

    2005-01-01

    New wireless technologies make possible the implementation of high level integration wireless devices which allow the replacement of traditional large wired monitoring devices. This kind of devices favours at-home hospitalization, reducing the affluence to sanitary assistance centers to make routine controls. This fact causes a really favourable social impact, especially for elder people, rural-zone inhabitant, chronic patients and handicapped people. Furthermore, it offers new functionalities to physicians and will reduce the sanitary cost. Among these functionalities, biomedical signals can be sent to other devices (screen, PDA, PC...) or processing centers, without restricting the patients' mobility. The aim of this project is the development and implementation of a reduced size multi-channel electrocardiograph based on IEEE 802.11, which allows wireless monitoring of patients, and the insertion of the information into the TCP/IP Hospital network.

  8. High Fidelity Simulations of Large-Scale Wireless Networks

    Energy Technology Data Exchange (ETDEWEB)

    Onunkwo, Uzoma [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Benz, Zachary [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2015-11-01

    The worldwide proliferation of wireless connected devices continues to accelerate. There are 10s of billions of wireless links across the planet with an additional explosion of new wireless usage anticipated as the Internet of Things develops. Wireless technologies do not only provide convenience for mobile applications, but are also extremely cost-effective to deploy. Thus, this trend towards wireless connectivity will only continue and Sandia must develop the necessary simulation technology to proactively analyze the associated emerging vulnerabilities. Wireless networks are marked by mobility and proximity-based connectivity. The de facto standard for exploratory studies of wireless networks is discrete event simulations (DES). However, the simulation of large-scale wireless networks is extremely difficult due to prohibitively large turnaround time. A path forward is to expedite simulations with parallel discrete event simulation (PDES) techniques. The mobility and distance-based connectivity associated with wireless simulations, however, typically doom PDES and fail to scale (e.g., OPNET and ns-3 simulators). We propose a PDES-based tool aimed at reducing the communication overhead between processors. The proposed solution will use light-weight processes to dynamically distribute computation workload while mitigating communication overhead associated with synchronizations. This work is vital to the analytics and validation capabilities of simulation and emulation at Sandia. We have years of experience in Sandia’s simulation and emulation projects (e.g., MINIMEGA and FIREWHEEL). Sandia’s current highly-regarded capabilities in large-scale emulations have focused on wired networks, where two assumptions prevent scalable wireless studies: (a) the connections between objects are mostly static and (b) the nodes have fixed locations.

  9. PRIORITY BASED PACKET SCHEDULING APPROACH FOR WIRELESS SENSOR NETWORKS

    OpenAIRE

    K. K. Kannan

    2017-01-01

    A priority based packet scheduling scheme is proposed which aims at scheduling different types of data packets, such as real time and non-real-time data packets at sensor nodes with resource constraints in Wireless Sensor Networks. Most of the existing packet-scheduling mechanisms of Wireless Sensor Networks use First Come First Served (FCFS), non-preemptive priority and preemptive priority scheduling algorithms. These algorithms results in long end-to-end data transmission delay, high energy...

  10. Energy-aware Wireless Multi-hop Networks

    OpenAIRE

    Vazifehdan, J.

    2011-01-01

    Wireless networks have provided us a variety of services which facilitate communication between people beyond the physical boundaries. Mobile telephony, mobile Internet and high-deffnition video calls are examples of services supported by modern networks nowadays. Beyond this, enhancements in processing capabilities of electronic devices coupled with advances in wireless communication have resulted in the emergence of devices which have high processing and communication capabilities. Small de...

  11. Seamless and secure communications over heterogeneous wireless networks

    CERN Document Server

    Cao, Jiannong

    2014-01-01

    This brief provides an overview of the requirements, challenges, design issues and major techniques for seamless and secure communications over heterogeneous wireless networks. It summarizes and provides detailed insights into the latest research on handoff management, mobility management, fast authentication and security management to support seamless and secure roaming for mobile clients. The reader will also learn about the challenges in developing relevant technologies and providing ubiquitous Internet access over heterogeneous wireless networks. The authors have extensive experience in im

  12. Wireless Sensor Networks for Long Distance Pipeline Monitoring

    OpenAIRE

    Augustine C. Azubogu; Victor E. Idigo; Schola U. Nnebe; Obinna S. Oguejiofor; Simon E.

    2013-01-01

    The main goal of this seminal paper is to introduce the application of Wireless Sensor Networks (WSN) in long distance infrastructure monitoring (in particular in pipeline infrastructure monitoring) – one of the on-going research projects by the Wireless Communication Research Group at the department of Electronic and Computer Engineering, Nnamdi Azikiwe University, Awka. The current sensor network architectures for monitoring long distance pipeline infrastructures are pr...

  13. Application of wireless sensor network technology in logistics information system

    Science.gov (United States)

    Xu, Tao; Gong, Lina; Zhang, Wei; Li, Xuhong; Wang, Xia; Pan, Wenwen

    2017-04-01

    This paper introduces the basic concepts of active RFID (WSN-ARFID) based on wireless sensor networks and analyzes the shortcomings of the existing RFID-based logistics monitoring system. Integrated wireless sensor network technology and the scrambling point of RFID technology. A new real-time logistics detection system based on WSN and RFID, a model of logistics system based on WSN-ARFID is proposed, and the feasibility of this technology applied to logistics field is analyzed.

  14. Coverage and Connectivity Issue in Wireless Sensor Networks

    Directory of Open Access Journals (Sweden)

    Rachit Trivedi

    2013-04-01

    Full Text Available Wireless sensor networks (WSNs are an emerging area of interest in research and development. It finds use in military surveillance, health care, environmental monitoring, forest fire detection and smart environments. An important research issue in WSNs is the coverage since cost, area and lifetime are directly validated to it.In this paper we present an overview of WSNs and try to refine the coverage and connectivity issues in wireless sensor networks.

  15. Implementation of Low Power Multi-hop Wireless Sensor Network

    Directory of Open Access Journals (Sweden)

    Zhou Jianhong

    2016-01-01

    Full Text Available In this paper, the multi-hop wireless sensor network is created, which is realized by Micaz and Mib520 Board using TinyOS and Cygwin. The mote transmission mode is engaged and off-the-shelf protocols and algorithm, RSSI and PDR, are applied in this wireless network and the performance is improved. Several experiments are proposed to set standard RSSI threshold value to allow the user to send packet with efficient power level.

  16. Survey of Security Technologies on Wireless Sensor Networks

    Directory of Open Access Journals (Sweden)

    Qiuwei Yang

    2015-01-01

    Full Text Available Because of their low cost and adaptability, wireless sensor networks are widely used in civil, military, and commercial fields and other fields. However, since the sensor node in the calculation of the capacity, battery capacity, and storage capacity are restricted by the limitations and inherent characteristics of the sensor networks, compared to traditional networks, which makes wireless sensor networks face more security threats. This paper summarized research progress of sensor network security issues as three aspects, key management, authentication, and secure routing, analyzed and commented on these results advantages and disadvantages and pointed out the future direction of the hot research field.

  17. Time synchronization in ad-hoc wireless sensor networks

    Science.gov (United States)

    Sharma, Nishant

    2013-06-01

    Advances in micro-electronics and developments in the various technologies have given birth to this era of wireless sensor networks. A sensor network is the one which provides information about the surrounding environment by sensing it and clock synchronization in wireless sensor networks plays a vital role to maintain the integrity of entire network. In this paper two major low energy consumption clock synchronization algorithms, Reference Broadcast Synchronization (RBS) and Timing-Sync Protocol for Sensor Networks (TPSN) are simulated, which result in high level of accuracy, reliability, handles substantially greater node densities, supports mobility, and hence perform well under all possible conditions.

  18. Optimized Solar Energy Power Supply for Remote Wireless Sensors Based on IEEE 802.15.4 Standard

    Directory of Open Access Journals (Sweden)

    Ondrej Krejcar

    2012-01-01

    Full Text Available Powering of intelligent wireless sensors without a permanent electric connection is a general problem which is often solved by adopting alternative power sources. One of the most commonly used sources is solar energy in the form of solar panel and charging circuits. However, it is not possible to find a solution in the markets for operation in changeable weather conditions, where sun intensity is not so high. This fact leads us to the development of optimized solar panel and all circuits for reliable power supply of wireless sensors. A special charging circuit for Li-ION battery and DC-DC adapter circuit for stabilization of wireless sensor working voltage were developed and optimized for very low energy consumption and high efficiency.

  19. Integrated resource management for Hybrid Optical Wireless (HOW) networks

    DEFF Research Database (Denmark)

    Yan, Ying; Yu, Hao; Wessing, Henrik

    2009-01-01

    resource sharing scheme and an integrated admission control scheme for the hybrid optical wireless networks. It provides QoS guarantees for connections through both optical and wireless domain. Simulation results show that our proposed scheme improves QoS performances in terms of high throughput and low......Efficient utilization of available bandwidth over hybrid optical wireless networks is a critical issue, especially for multimedia applications with high data rates and stringent Quality of Service (QoS) requirements. In this paper, we propose an integrated resource management including an enhanced...

  20. Radio propagation and adaptive antennas for wireless communication networks

    CERN Document Server

    Blaunstein, Nathan

    2014-01-01

    Explores novel wireless networks beyond 3G, and advanced 4G technologies, such as MIMO, via propagation phenomena and the fundamentals of adapted antenna usage.Explains how adaptive antennas can improve GoS and QoS for any wireless channel, with specific examples and applications in land, aircraft and satellite communications.Introduces new stochastic approach based on several multi-parametric models describing various terrestrial scenarios, which have been experimentally verified in different environmental conditionsNew chapters on fundamentals of wireless networks, cellular and non-cellular,

  1. Scalable Architecture for Multihop Wireless ad Hoc Networks

    Science.gov (United States)

    Arabshahi, Payman; Gray, Andrew; Okino, Clayton; Yan, Tsun-Yee

    2004-01-01

    A scalable architecture for wireless digital data and voice communications via ad hoc networks has been proposed. Although the details of the architecture and of its implementation in hardware and software have yet to be developed, the broad outlines of the architecture are fairly clear: This architecture departs from current commercial wireless communication architectures, which are characterized by low effective bandwidth per user and are not well suited to low-cost, rapid scaling in large metropolitan areas. This architecture is inspired by a vision more akin to that of more than two dozen noncommercial community wireless networking organizations established by volunteers in North America and several European countries.

  2. A framework for multi-object tracking over distributed wireless camera networks

    Science.gov (United States)

    Gau, Victor; Hwang, Jenq-Neng

    2010-07-01

    In this paper, we propose a unified framework targeting at two important issues in a distributed wireless camera network, i.e., object tracking and network communication, to achieve reliable multi-object tracking over distributed wireless camera networks. In the object tracking part, we propose a fully automated approach for tracking of multiple objects across multiple cameras with overlapping and non-overlapping field of views without initial training. To effectively exchange the tracking information among the distributed cameras, we proposed an idle probability based broadcasting method, iPro, which adaptively adjusts the broadcast probability to improve the broadcast effectiveness in a dense saturated camera network. Experimental results for the multi-object tracking demonstrate the promising performance of our approach on real video sequences for cameras with overlapping and non-overlapping views. The modeling and ns-2 simulation results show that iPro almost approaches the theoretical performance upper bound if cameras are within each other's transmission range. In more general scenarios, e.g., in case of hidden node problems, the simulation results show that iPro significantly outperforms standard IEEE 802.11, especially when the number of competing nodes increases.

  3. A Power Balance Aware Wireless Charger Deployment Method for Complete Coverage in Wireless Rechargeable Sensor Networks

    Directory of Open Access Journals (Sweden)

    Tu-Liang Lin

    2016-08-01

    Full Text Available Traditional sensor nodes are usually battery powered, and the limited battery power constrains the overall lifespan of the sensors. Recently, wireless power transmission technology has been applied in wireless sensor networks (WSNs to transmit wireless power from the chargers to the sensor nodes and solve the limited battery power problem. The combination of wireless sensors and wireless chargers forms a new type of network called wireless rechargeable sensor networks (WRSNs. In this research, we focus on how to effectively deploy chargers to maximize the lifespan of a network. In WSNs, the sensor nodes near the sink consume more power than nodes far away from the sink because of frequent data forwarding. This important power unbalanced factor has not been considered, however, in previous charger deployment research. In this research, a power balance aware deployment (PBAD method is proposed to address the power unbalance in WRSNs and to design the charger deployment with maximum charging efficiency. The proposed deployment method is effectively aware of the existence of the sink node that would cause unbalanced power consumption in WRSNs. The simulation results show that the proposed PBAD algorithm performs better than other deployment methods, and fewer chargers are deployed as a result.

  4. Energy efficient topology control algorithm for wireless mesh networks

    CSIR Research Space (South Africa)

    Aron, FO

    2008-08-01

    Full Text Available The control of the topology of a network makes it possible for the network nodes to reduce their power of transmission while ensuring that network connectivity is preserved. This paper explains the need for energy consumption control in Wireless...

  5. Mechanized Extraction of Topology Anti-patterns in Wireless Networks

    NARCIS (Netherlands)

    Woehrle, M.; Bakhshi, R.R.; Mousavi, M.R.

    2012-01-01

    Exhaustive and mechanized formal verification of wireless networks is hampered by the huge number of possible topologies and the large size of the actual networks. However, the generic communication structure in such networks allows for reducing the root causes of faults to faulty (sub-)topologies,

  6. Low power radio communication platform for wireless sensor network

    NARCIS (Netherlands)

    Dutta, R.; Bentum, Marinus Jan; van der Zee, Ronan A.R.; Kokkeler, Andre B.J.

    2009-01-01

    Wireless sensor networks are predicted to be the most versatile, popular and useful technology in the near future. A large number of applications are targeted which will hugely benefit from a network of tiny computers with few sensors, radio communication platform, intelligent networking and

  7. Strategic Vision on Convergence of Wired and Wireless Networks

    DEFF Research Database (Denmark)

    Prasad, Ramjee; Olsen, Rasmus Løvenstein; Saarnio, Juha

    2006-01-01

    less structure within wireless communication. Furthermore we discuss some of the important aspects in personalisation of future network paradigms with focus on how networks and network services will be able to sense the user’s environment and adapt to this. Finally we discuss one of the most important...... aspect, namely security and privacy issues within future generationnetworks....

  8. Flow transfer times in wireless multihop ad hoc networks

    NARCIS (Netherlands)

    Coenen, Tom Johannes Maria; van den Berg, Hans Leo; Boucherie, Richardus J.; Kouvatsos, D.

    2009-01-01

    A flow level model for multihop wireless ad hoc networks is presented in this paper. Using a flow level view, we show the main properties and modeling challenges for ad hoc networks. Considering different scenarios, a multihop WLAN and a serial network with a TCP-like flow control protocol, we

  9. Design and implementation of a topology control scheme for wireless mesh networks

    CSIR Research Space (South Africa)

    Mudali, P

    2009-09-01

    Full Text Available The Wireless Mesh Network (WMN) backbone is usually comprised of stationary nodes but the transient nature of wireless links results in changing network topologies. Topology Control (TC) aims to preserve network connectivity in ad hoc and mesh...

  10. Dynamic Session-Key Generation for Wireless Sensor Networks

    Directory of Open Access Journals (Sweden)

    Cheng-Ta Li

    2008-09-01

    Full Text Available Recently, wireless sensor networks have been used extensively in different domains. For example, if the wireless sensor node of a wireless sensor network is distributed in an insecure area, a secret key must be used to protect the transmission between the sensor nodes. Most of the existing methods consist of preselecting m keys from a key pool and forming a key chain. Then, the sensor nodes make use of the key chain to encrypt the data. However, while the secret key is being transmitted, it can easily be exposed during transmission. We propose a dynamic key management protocol, which can improve the security of the key juxtaposed to existing methods. Additionally, the dynamic update of the key can lower the probability of the key to being guessed correctly. In addition, with the new protocol, attacks on the wireless sensor network can be avoided.

  11. Information Security of PHY Layer in Wireless Networks

    Directory of Open Access Journals (Sweden)

    Weidong Fang

    2016-01-01

    Full Text Available Since the characteristics of wireless channel are open and broadcasting, wireless networks are very vulnerable to be attacked via eavesdropping, jamming, and interference. As traditional secure technologies are not suitable for PHY layer of wireless networks, physical-layer security issues become a focus of attention. In this paper, we firstly identify and summarize the threats and vulnerabilities in PHY layer of wireless networks. Then, we give a holistic overview of PHY layer secure schemes, which are divided into three categories: spatial domain-based, time domain-based, and frequency domain-based. Along the way, we analyze the pros and cons of current secure technologies in each category. In addition, we also conclude the techniques and methods used in these categories and point out the open research issues and directions in this area.

  12. Data Aggregation with Sequential Detection in Wireless Sensors Network

    Directory of Open Access Journals (Sweden)

    Song Xiao-Ou

    2014-10-01

    Full Text Available As the advanced information acquiring technology, wireless sensor networks are being applied in more and more areas. Data aggregation is the effective information processing to solve the energy saving problem of WSN (Wireless Sensor Network. Most existing data aggregation algorithm discuss fusion problem in the scene that the number of nodes is fixed. However, the amount of data transmitted is directly proportional to the number of nodes. Hence the appropriate strategy should be that the number of nodes is alterable under the satisfaction of performance. In this paper, sequential detection is applied in data aggregation for wireless sensor network. And the mathematical model is established. Considering the fading problem of wireless channel and the characters of physical layer, WSN data aggregation with sequential detection (WDASD is proposed. The characters of WDASD are tested by simulations. In the end, a cross-layer scheme is proposed and simulation test is made to validate it.

  13. Dynamic Session-Key Generation for Wireless Sensor Networks

    Directory of Open Access Journals (Sweden)

    Chen Chin-Ling

    2008-01-01

    Full Text Available Abstract Recently, wireless sensor networks have been used extensively in different domains. For example, if the wireless sensor node of a wireless sensor network is distributed in an insecure area, a secret key must be used to protect the transmission between the sensor nodes. Most of the existing methods consist of preselecting keys from a key pool and forming a key chain. Then, the sensor nodes make use of the key chain to encrypt the data. However, while the secret key is being transmitted, it can easily be exposed during transmission. We propose a dynamic key management protocol, which can improve the security of the key juxtaposed to existing methods. Additionally, the dynamic update of the key can lower the probability of the key to being guessed correctly. In addition, with the new protocol, attacks on the wireless sensor network can be avoided.

  14. On Radio over Fiber for Heterogeneous Wireless Networks

    DEFF Research Database (Denmark)

    Riaz, M. Tahir; Nielsen, Rasmus Hjorth; Pedersen, Jens Myrup

    2009-01-01

    The paper provides an overview of the radio over fiber (RoF) technology and its potential use in heterogeneous wireless networks. Wireless communications have seen a huge growth in the last decade. It has been estimated that five in every six people in the entire world will have a mobile phone...... in 2010. The vast growing use of Internet on the mobile devices has also been increased significantly. In order to provide a broadband access for mobile communications, a new wireless infrastructure (fiber optic networks for distributed, extendible heterogeneous radio architectures and service...... provisioning - FUTON) based on RoF technology has been introduced. The project adopts centralized processing of radio signals for number of wireless base stations can enhance the network performance in terms of bandwidth, and QoS parameters. The simplified remote access units (RAU) are expected to not only...

  15. Quantum-classical access networks with embedded optical wireless links

    Science.gov (United States)

    Elmabrok, Osama; Ghalaii, Masoud; Razavi, Mohsen

    2018-03-01

    We examine the applicability of wireless indoor quantum key distribution (QKD) in hybrid quantum-classical networks. We propose practical configurations that would enable wireless access to such networks. The proposed setups would allow an indoor wireless user, equipped with a QKD-enabled mobile device, to communicate securely with a remote party on the other end of the access network. QKD signals, sent through wireless indoor channels, are combined with classical ones and sent over shared fiber links to the remote user. Dense wavelengthdivision multiplexing would enable the simultaneous transmission of quantum and classical signals over the same fiber. We consider the adverse effects of the background noise induced by Raman scattered light on the QKD receivers due to such an integration. In addition, we consider the loss and the background noise that arise from indoor environments. We consider a number of discrete and continuous-variable QKD protocols and study their performance in different scenarios.

  16. Competition in the domain of wireless networks security

    Science.gov (United States)

    Bednarczyk, Mariusz

    2017-04-01

    Wireless networks are very popular and have found wide spread usage amongst various segments, also in military environment. The deployment of wireless infrastructures allow to reduce the time it takes to install and dismantle communications networks. With wireless, users are more mobile and can easily get access to the network resources all the time. However, wireless technologies like WiFi or Bluetooth have security issues that hackers have extensively exploited over the years. In the paper several serious security flaws in wireless technologies are presented. Most of them enable to get access to the internal networks and easily carry out man-in-the-middle attacks. Very often, they are used to launch massive denial of service attacks that target the physical infrastructure as well as the RF spectrum. For instance, there are well known instances of Bluetooth connection spoofing in order to steal WiFi password stored in the mobile device. To raise the security awareness and protect wireless networks against an adversary attack, an analysis of attack methods and tools over time is presented in the article. The particular attention is paid to the severity, possible targets as well as the ability to persist in the context of protective measures. Results show that an adversary can take complete control of the victims' mobile device features if the users forget to use simple safety principles.

  17. Using Wireless Network Coding to Replace a Wired with Wireless Backhaul

    DEFF Research Database (Denmark)

    Thomsen, Henning; De Carvalho, Elisabeth; Popovski, Petar

    2014-01-01

    of wireless emulated wire (WEW), based on two-way relaying and network coding. This setup leads to a new type of broadcast problem, with decoding conditions that are specific to the requirement for equivalence to the wired backhaul. We formulate and solve the associated optimization problems. The proposed...... approach is a convincing argument that wireless backhauling solutions should be designed and optimized for two-way communication....

  18. Wireless ad hoc and sensor networks management, performance, and applications

    CERN Document Server

    He, Jing

    2013-01-01

    Although wireless sensor networks (WSNs) have been employed across a wide range of applications, there are very few books that emphasize the algorithm description, performance analysis, and applications of network management techniques in WSNs. Filling this need, Wireless Ad Hoc and Sensor Networks: Management, Performance, and Applications summarizes not only traditional and classical network management techniques, but also state-of-the-art techniques in this area. The articles presented are expository, but scholarly in nature, including the appropriate history background, a review of current

  19. Comparison of Different Scenarios for Path Diversity Packet Wireless Networks

    Directory of Open Access Journals (Sweden)

    Petr Chlumsky

    2012-01-01

    Full Text Available This article discusses the use of the principles of network coding in wireless networks to increase the overall robustness of the transmission. Path diversity on the packet level is investigated as a software alternative to classical diversity techniques commonly used to improve wireless devices communication. The article describes the initial stage of the research of network coding in elementary form with network traffic duplication. Objects of investigation are two different types of transmission in two scenarios, where the resulting transmission loss is evaluated with dependency on the packet length.

  20. Energy Aware Clustering Algorithms for Wireless Sensor Networks

    Science.gov (United States)

    Rakhshan, Noushin; Rafsanjani, Marjan Kuchaki; Liu, Chenglian

    2011-09-01

    The sensor nodes deployed in wireless sensor networks (WSNs) are extremely power constrained, so maximizing the lifetime of the entire networks is mainly considered in the design. In wireless sensor networks, hierarchical network structures have the advantage of providing scalable and energy efficient solutions. In this paper, we investigate different clustering algorithms for WSNs and also compare these clustering algorithms based on metrics such as clustering distribution, cluster's load balancing, Cluster Head's (CH) selection strategy, CH's role rotation, node mobility, clusters overlapping, intra-cluster communications, reliability, security and location awareness.

  1. Quality of Service Metrics in Wireless Sensor Networks: A Survey

    Science.gov (United States)

    Snigdh, Itu; Gupta, Nisha

    2016-03-01

    Wireless ad hoc network is characterized by autonomous nodes communicating with each other by forming a multi hop radio network and maintaining connectivity in a decentralized manner. This paper presents a systematic approach to the interdependencies and the analogy of the various factors that affect and constrain the wireless sensor network. This article elaborates the quality of service parameters in terms of methods of deployment, coverage and connectivity which affect the lifetime of the network that have been addressed, till date by the different literatures. The analogy of the indispensable rudiments was discussed that are important factors to determine the varied quality of service achieved, yet have not been duly focused upon.

  2. Enabling Secure High-Performance Wireless Ad Hoc Networking

    Science.gov (United States)

    2003-05-29

    Carl Meyer, and Jonathan Oseas. Generating Strong One-Way Functions with Cryptographic Algorithm. 27:5658–5659, 1985. [119] Marshall Kirk McKusick... Culler , and J. D. Tygar. SPINS: Security Protocols for Sensor Networks. In Proceedings of the Seventh Annual International Conference on Mobile...David L. Tennenhouse, Jonathan M. Smith, W. David Sincoskie, David J. Wetherall, and Gary J. Minden. A Survey of Active Network Research. IEEE

  3. Connectivity Restoration in Wireless Sensor Networks via Space Network Coding.

    Science.gov (United States)

    Uwitonze, Alfred; Huang, Jiaqing; Ye, Yuanqing; Cheng, Wenqing

    2017-04-20

    The problem of finding the number and optimal positions of relay nodes for restoring the network connectivity in partitioned Wireless Sensor Networks (WSNs) is Non-deterministic Polynomial-time hard (NP-hard) and thus heuristic methods are preferred to solve it. This paper proposes a novel polynomial time heuristic algorithm, namely, Relay Placement using Space Network Coding (RPSNC), to solve this problem, where Space Network Coding, also called Space Information Flow (SIF), is a new research paradigm that studies network coding in Euclidean space, in which extra relay nodes can be introduced to reduce the cost of communication. Unlike contemporary schemes that are often based on Minimum Spanning Tree (MST), Euclidean Steiner Minimal Tree (ESMT) or a combination of MST with ESMT, RPSNC is a new min-cost multicast space network coding approach that combines Delaunay triangulation and non-uniform partitioning techniques for generating a number of candidate relay nodes, and then linear programming is applied for choosing the optimal relay nodes and computing their connection links with terminals. Subsequently, an equilibrium method is used to refine the locations of the optimal relay nodes, by moving them to balanced positions. RPSNC can adapt to any density distribution of relay nodes and terminals, as well as any density distribution of terminals. The performance and complexity of RPSNC are analyzed and its performance is validated through simulation experiments.

  4. Alternative Path Communication in Wide-Scale Cluster-Tree Wireless Sensor Networks Using Inactive Periods.

    Science.gov (United States)

    Leão, Erico; Montez, Carlos; Moraes, Ricardo; Portugal, Paulo; Vasques, Francisco

    2017-05-06

    The IEEE 802.15.4/ZigBee cluster-tree topology is a suitable technology to deploy wide-scale Wireless Sensor Networks (WSNs). These networks are usually designed to support convergecast traffic, where all communication paths go through the PAN (Personal Area Network) coordinator. Nevertheless, peer-to-peer communication relationships may be also required for different types of WSN applications. That is the typical case of sensor and actuator networks, where local control loops must be closed using a reduced number of communication hops. The use of communication schemes optimised just for the support of convergecast traffic may result in higher network congestion and in a potentially higher number of communication hops. Within this context, this paper proposes an Alternative-Route Definition (ARounD) communication scheme for WSNs. The underlying idea of ARounD is to setup alternative communication paths between specific source and destination nodes, avoiding congested cluster-tree paths. These alternative paths consider shorter inter-cluster paths, using a set of intermediate nodes to relay messages during their inactive periods in the cluster-tree network. Simulation results show that the ARounD communication scheme can significantly decrease the end-to-end communication delay, when compared to the use of standard cluster-tree communication schemes. Moreover, the ARounD communication scheme is able to reduce the network congestion around the PAN coordinator, enabling the reduction of the number of message drops due to queue overflows in the cluster-tree network.

  5. Secure Geographic Routing in Ad Hoc and Wireless Sensor Networks

    Directory of Open Access Journals (Sweden)

    Zahariadis Theodore

    2010-01-01

    Full Text Available Security in sensor networks is one of the most relevant research topics in resource constrained wireless devices and networks. Several attacks can be suffered in ad hoc and wireless sensor networks (WSN, which are highly susceptible to attacks, due to the limited resources of the nodes. In this paper, we propose innovative and lightweight localization techniques that allow for intrusion identification and isolation schemes and provide accurate location information. This information is used by our routing protocol which additionally incorporates a distributed trust model to prevent several routing attacks to the network. We finally evaluate our algorithms for accurate localization and for secure routing which have been implemented and tested in real ad hoc and wireless sensor networks.

  6. Ninth International Conference on Wireless Communication and Sensor Networks

    CERN Document Server

    Tiwari, Murlidhar; Arora, Anish

    2014-01-01

    Wireless communication and sensor networks would form the backbone to create pervasive and ubiquitous environments that would have profound influence on the society and thus are important to the society. The wireless communication technologies and wireless sensor networks would encompass a wide range of domains such as HW devices such as motes, sensors and associated instrumentation, actuators, transmitters, receivers, antennas, etc., sensor network aspects such as topologies, routing algorithms, integration of heterogeneous network elements and topologies, designing RF devices and systems for energy efficiency and reliability etc. These sensor networks would provide opportunity to continuously and in a distributed manner monitor the environment and generate the necessary warnings and actions. However most of the developments have been demonstrated only in controlled and laboratory environments. So we are yet to see those powerful, ubiquitous applications for the benefit of the society. The conference and con...

  7. Sending policies in dynamic wireless mesh using network coding

    DEFF Research Database (Denmark)

    Pandi, Sreekrishna; Fitzek, Frank; Pihl, Jeppe

    2015-01-01

    This paper demonstrates the quick prototyping capabilities of the Python-Kodo library for network coding based performance evaluation and investigates the problem of data redundancy in a network coded wireless mesh with opportunistic overhearing. By means of several wireless meshed architectures...... of appropriate relays. Finally, various sending policies that can be employed by the nodes in order to improve the overall transmission efficiency in a dynamic wireless mesh network are discussed and their performance is analysed on the constructed simulation setup....... simulated on the constructed test-bed, the advantage of network coding over state of the art routing schemes and the challenges of this new technology are shown. By providing maximum control of the network coding parameters and the simulation environment to the user, the test-bed facilitates quick...

  8. Multi-objective ant algorithm for wireless sensor network positioning

    International Nuclear Information System (INIS)

    Fidanova, S.; Shindarov, M.; Marinov, P.

    2013-01-01

    It is impossible to imagine our modern life without telecommunications. Wireless networks are a part of telecommunications. Wireless sensor networks (WSN) consist of spatially distributed sensors, which communicate in wireless way. This network monitors physical or environmental conditions. The objective is the full coverage of the monitoring region and less energy consumption of the network. The most appropriate approach to solve the problem is metaheuristics. In this paper the full coverage of the area is treated as a constrain. The objectives which are optimized are a minimal number of sensors and energy (lifetime) of the network. We apply multi-objective Ant Colony Optimization to solve this important telecommunication problem. We chose MAX-MIN Ant System approach, because it is proven to converge to the global optima

  9. Geographic wormhole detection in wireless sensor networks.

    Directory of Open Access Journals (Sweden)

    Mehdi Sookhak

    Full Text Available Wireless sensor networks (WSNs are ubiquitous and pervasive, and therefore; highly susceptible to a number of security attacks. Denial of Service (DoS attack is considered the most dominant and a major threat to WSNs. Moreover, the wormhole attack represents one of the potential forms of the Denial of Service (DoS attack. Besides, crafting the wormhole attack is comparatively simple; though, its detection is nontrivial. On the contrary, the extant wormhole defense methods need both specialized hardware and strong assumptions to defend against static and dynamic wormhole attack. The ensuing paper introduces a novel scheme to detect wormhole attacks in a geographic routing protocol (DWGRP. The main contribution of this paper is to detect malicious nodes and select the best and the most reliable neighbors based on pairwise key pre-distribution technique and the beacon packet. Moreover, this novel technique is not subject to any specific assumption, requirement, or specialized hardware, such as a precise synchronized clock. The proposed detection method is validated by comparisons with several related techniques in the literature, such as Received Signal Strength (RSS, Authentication of Nodes Scheme (ANS, Wormhole Detection uses Hound Packet (WHOP, and Wormhole Detection with Neighborhood Information (WDI using the NS-2 simulator. The analysis of the simulations shows promising results with low False Detection Rate (FDR in the geographic routing protocols.

  10. Wireless sensor networks for structural health monitoring

    CERN Document Server

    Cao, Jiannong

    2016-01-01

    This brief covers the emerging area of wireless sensor network (WSN)-based structural health monitoring (SHM) systems, and introduces the authors’ WSN-based platform called SenetSHM. It helps the reader differentiate specific requirements of SHM applications from other traditional WSN applications, and demonstrates how these requirements are addressed by using a series of systematic approaches. The brief serves as a practical guide, explaining both the state-of-the-art technologies in domain-specific applications of WSNs, as well as the methodologies used to address the specific requirements for a WSN application. In particular, the brief offers instruction for problem formulation and problem solving based on the authors’ own experiences implementing SenetSHM. Seven concise chapters cover the development of hardware and software design of SenetSHM, as well as in-field experiments conducted while testing the platform. The brief’s exploration of the SenetSHM platform is a valuable feature for civil engine...

  11. Ultra wideband wireless body area networks

    CERN Document Server

    Thotahewa, Kasun Maduranga Silva; Yuce, Mehmet Rasit

    2014-01-01

    This book explores the design of ultra wideband (UWB) technology for wireless body-area networks (WBAN).  The authors describe a novel implementation of WBAN sensor nodes that use UWB for data transmission and narrow band for data reception, enabling low power sensor nodes, with high data rate capability.  The discussion also includes power efficient, medium access control (MAC) protocol design for UWB based WBAN applications and the authors present a MAC protocol in which a guaranteed delivery mechanism is utilized to transfer data with high priority.  Readers will also benefit from this book’s feasibility analysis of the UWB technology for human implant applications through the study of electromagnetic and thermal power absorption of human tissue that is exposed to UWB signals.   • Describes hardware platform development for IR-UWB based WBAN communication; • Discusses power efficient medium access control (MAC) protocol design for IR-UWB based WBAN applications; • Includes feasibility analy...

  12. Geographic wormhole detection in wireless sensor networks.

    Science.gov (United States)

    Sookhak, Mehdi; Akhundzada, Adnan; Sookhak, Alireza; Eslaminejad, Mohammadreza; Gani, Abdullah; Khurram Khan, Muhammad; Li, Xiong; Wang, Xiaomin

    2015-01-01

    Wireless sensor networks (WSNs) are ubiquitous and pervasive, and therefore; highly susceptible to a number of security attacks. Denial of Service (DoS) attack is considered the most dominant and a major threat to WSNs. Moreover, the wormhole attack represents one of the potential forms of the Denial of Service (DoS) attack. Besides, crafting the wormhole attack is comparatively simple; though, its detection is nontrivial. On the contrary, the extant wormhole defense methods need both specialized hardware and strong assumptions to defend against static and dynamic wormhole attack. The ensuing paper introduces a novel scheme to detect wormhole attacks in a geographic routing protocol (DWGRP). The main contribution of this paper is to detect malicious nodes and select the best and the most reliable neighbors based on pairwise key pre-distribution technique and the beacon packet. Moreover, this novel technique is not subject to any specific assumption, requirement, or specialized hardware, such as a precise synchronized clock. The proposed detection method is validated by comparisons with several related techniques in the literature, such as Received Signal Strength (RSS), Authentication of Nodes Scheme (ANS), Wormhole Detection uses Hound Packet (WHOP), and Wormhole Detection with Neighborhood Information (WDI) using the NS-2 simulator. The analysis of the simulations shows promising results with low False Detection Rate (FDR) in the geographic routing protocols.

  13. Geographic Wormhole Detection in Wireless Sensor Networks

    Science.gov (United States)

    Sookhak, Mehdi; Akhundzada, Adnan; Sookhak, Alireza; Eslaminejad, Mohammadreza; Gani, Abdullah; Khurram Khan, Muhammad; Li, Xiong; Wang, Xiaomin

    2015-01-01

    Wireless sensor networks (WSNs) are ubiquitous and pervasive, and therefore; highly susceptible to a number of security attacks. Denial of Service (DoS) attack is considered the most dominant and a major threat to WSNs. Moreover, the wormhole attack represents one of the potential forms of the Denial of Service (DoS) attack. Besides, crafting the wormhole attack is comparatively simple; though, its detection is nontrivial. On the contrary, the extant wormhole defense methods need both specialized hardware and strong assumptions to defend against static and dynamic wormhole attack. The ensuing paper introduces a novel scheme to detect wormhole attacks in a geographic routing protocol (DWGRP). The main contribution of this paper is to detect malicious nodes and select the best and the most reliable neighbors based on pairwise key pre-distribution technique and the beacon packet. Moreover, this novel technique is not subject to any specific assumption, requirement, or specialized hardware, such as a precise synchronized clock. The proposed detection method is validated by comparisons with several related techniques in the literature, such as Received Signal Strength (RSS), Authentication of Nodes Scheme (ANS), Wormhole Detection uses Hound Packet (WHOP), and Wormhole Detection with Neighborhood Information (WDI) using the NS-2 simulator. The analysis of the simulations shows promising results with low False Detection Rate (FDR) in the geographic routing protocols. PMID:25602616

  14. Power Consumption Reduction for Wireless Sensor Networks Using A Fuzzy Approach

    Directory of Open Access Journals (Sweden)

    Giovanni Pau

    2016-01-01

    Full Text Available The increasing complexity of Wireless Sensor Networks (WSNs is leading towards the deployment of complex networked systems and the optimal design of WSNs can be a very difficult task because several constraints and requirements must be considered, among all the power consumption. This paper proposes a novel fuzzy logic based mechanism that according to the battery level and to the ratio of Throughput to Workload determines the sleeping time of sensor devices in a Wireless Sensor Network for environmental monitoring based on the IEEE 802.15.4 protocol. The main aim here is to find an effective solution that achieves the target while avoiding complex and computationally expensive solutions, which would not be appropriate for the problem at hand and would impair the practical applicability of the approach in real scenarios. The results of several real test-bed scenarios show that the proposed system outperforms other solutions, significantly reducing the whole power consumption while maintaining good performance in terms of the ratio of throughput to workload. An implementation on off-the-shelf devices proves that the proposed controller does not require powerful hardware and can be easily implemented on a low-cost device, thus paving the way for extensive usage in practice.

  15. Cross Layer PHY-MAC Protocol for Wireless Static and Mobile Ad Hoc Networks

    Directory of Open Access Journals (Sweden)

    Chris Blondia

    2008-11-01

    Full Text Available Multihop mobile wireless networks have drawn a lot of attention in recent years thanks to their wide applicability in civil and military environments. Since the existing IEEE 802.11 distributed coordination function (DCF standard does not provide satisfactory access to the wireless medium in multihop mobile networks, we have designed a cross-layer protocol, (CroSs-layer noise aware power driven MAC (SNAPdMac, which consists of two parts. The protocol first concentrates on the flexible adjustment of the upper and lower bounds of the contention window (CW to lower the number of collisions. In addition, it uses a power control scheme, triggered by the medium access control (MAC layer, to limit the waste of energy and also to decrease the number of collisions. Thanks to a noticeable energy conservation and decrease of the number of collisions, it prolongs significantly the lifetime of the network and delays the death of the first node while increasing both the throughput performance and the sending bit rate/throughput fairness among contending flows.

  16. Improving TCP Performance over Wireless Ad Hoc Networks with Busy Tone Assisted Scheme

    Directory of Open Access Journals (Sweden)

    Cai Lin

    2006-01-01

    Full Text Available It is well known that transmission control protocol (TCP performance degrades severely in IEEE 802.11-based wireless ad hoc networks. We first identify two critical issues leading to the TCP performance degradation: (1 unreliable broadcast, since broadcast frames are transmitted without the request-to-send and clear-to-send (RTS/CTS dialog and Data/ACK handshake, so they are vulnerable to the hidden terminal problem; and (2 false link failure which occurs when a node cannot successfully transmit data temporarily due to medium contention. We then propose a scheme to use a narrow-bandwidth, out-of-band busy tone channel to make reservation for broadcast and link error detection frames only. The proposed scheme is simple and power efficient, because only the sender needs to transmit two short messages in the busy tone channel before sending broadcast or link error detection frames in the data channel. Analytical results show that the proposed scheme can dramatically reduce the collision probability of broadcast and link error detection frames. Extensive simulations with different network topologies further demonstrate that the proposed scheme can improve TCP throughput by 23% to 150%, depending on user mobility, and effectively enhance both short-term and long-term fairness among coexisting TCP flows in multihop wireless ad hoc networks.

  17. Network performance and fault analytics for LTE wireless service providers

    CERN Document Server

    Kakadia, Deepak; Gilgur, Alexander

    2017-01-01

     This book is intended to describe how to leverage emerging technologies big data analytics and SDN, to address challenges specific to LTE and IP network performance and fault management data in order to more efficiently manage and operate an LTE wireless networks. The proposed integrated solutions permit the LTE network service provider to operate entire integrated network, from RAN to Core , from UE to application service, as one unified system and correspondingly collect and align disparate key metrics and data, using an integrated and holistic approach to network analysis. The LTE wireless network performance and fault involves the network performance and management of network elements in EUTRAN, EPC and IP transport components, not only as individual components, but also as nuances of inter-working of these components. The key metrics for EUTRAN include radio access network accessibility, retainability, integrity, availability and mobility. The key metrics for EPC include MME accessibility, mobility and...

  18. Wireless Sensors and Networks for Advanced Energy Management

    Energy Technology Data Exchange (ETDEWEB)

    Hardy, J.E.

    2005-05-06

    Numerous national studies and working groups have identified low-cost, very low-power wireless sensors and networks as a critical enabling technology for increasing energy efficiency, reducing waste, and optimizing processes. Research areas for developing such sensor and network platforms include microsensor arrays, ultra-low power electronics and signal conditioning, data/control transceivers, and robust wireless networks. A review of some of the research in the following areas will be discussed: (1) Low-cost, flexible multi-sensor array platforms (CO{sub 2}, NO{sub x}, CO, humidity, NH{sub 3}, O{sub 2}, occupancy, etc.) that enable energy and emission reductions in applications such as buildings and manufacturing; (2) Modeling investments (energy usage and savings to drive capital investment decisions) and estimated uptime improvements through pervasive gathering of equipment and process health data and its effects on energy; (3) Robust, self-configuring wireless sensor networks for energy management; and (4) Quality-of-service for secure and reliable data transmission from widely distributed sensors. Wireless communications is poised to support technical innovations in the industrial community, with widespread use of wireless sensors forecasted to improve manufacturing production and energy efficiency and reduce emissions. Progress being made in wireless system components, as described in this paper, is helping bring these projected improvements to reality.

  19. An 802.11k Compliant Framework for Cooperative Handoff in Wireless Networks

    Directory of Open Access Journals (Sweden)

    Thanasis Korakis

    2009-01-01

    Full Text Available In IEEE 802.11-based wireless networks, the stations (STAs are associated with the available access points (APs and communicate through them. In traditional handoff schemes, the STAs get information about the active APs in their neighborhood by scanning the available channels and listening to transmitted beacons. This paper proposes an 802.11k compliant framework for cooperative handoff where the STAs are informed about the active APs by exchanging information with neighboring STAs. Besides, the APs share useful information that can be used by the STAs in a handoff process. In this way, we minimize the delay of the scanning procedure. We evaluate the performance of our mechanisms through OPNET simulations. We demonstrate that our scheme reduces the scanning delay up to 92%. Consequently, our system is more capable in meeting the needs of QoS-sensitive applications.

  20. An 802.11k Compliant Framework for Cooperative Handoff in Wireless Networks

    Directory of Open Access Journals (Sweden)

    Korakis Thanasis

    2009-01-01

    Full Text Available Abstract In IEEE 802.11-based wireless networks, the stations (STAs are associated with the available access points (APs and communicate through them. In traditional handoff schemes, the STAs get information about the active APs in their neighborhood by scanning the available channels and listening to transmitted beacons. This paper proposes an 802.11k compliant framework for cooperative handoff where the STAs are informed about the active APs by exchanging information with neighboring STAs. Besides, the APs share useful information that can be used by the STAs in a handoff process. In this way, we minimize the delay of the scanning procedure. We evaluate the performance of our mechanisms through OPNET simulations. We demonstrate that our scheme reduces the scanning delay up to 92%. Consequently, our system is more capable in meeting the needs of QoS-sensitive applications.