Comparison of the results for quality implementation of low energy X rays

International Nuclear Information System (INIS)

Affonseca, M; Ochoa, R; Almeida, C.E. de; Peixoto, J.G.

2001-01-01

It describes the comparison of the results for qualities implementation of low energy X rays, using a pan tak tube, HF 160, which has tungsten white, beryllium window, is water-cooled and it has a 160 K B generator [es

Non-destructive test for VHTR fuel using 160kV X-ray system in Hotcell

Energy Technology Data Exchange (ETDEWEB)

Kim, Young Jun; Yoo, Boung Ok; Choo, Yong sun; Baik Sang youl; Kim, Hee Moon; Ahn, Sang Bok [KAERI, Daejeon (Korea, Republic of)

2016-05-15

The research for VHTR which is one of the next generation reactor has been actively carried out. As a part of the research for VHTR, an irradiation examination for the VHTR fuel was performed to confirm an in-pile behavior in HANARO. The non-destructive test for the irradiated fuel is very important to understand the in-pile behavior of the fuel. Especially, the X-ray system is useful to observe the fuel shape without destruction. A dimensional change and defect of the fuel can be confirmed thorough the Xray system. Also, using the 3-D software and CT technology, the fuel shape can be intuitionally observed. The 450kV and 160kV X-ray system were installed and operated in IMEF hotcell. The 160kV X-ray system relatively using a low voltage is suitable to a small scale sample. And high resolution images can be obtained. In this study, the non-destructive test for the unirradiated and irradiated VHTR fuel were performed using the 160kV X-ray system. Through these test, the possibility for the X-ray inspection of irradiated fuel was confirmed. The non-destructive test for the unirradiated and irradiated VHTR fuel were performed using the 160kV X-ray system. The clear images of the irradiated coated particle were produced without the radiation damage during the Xray inspection. The X-ray images of the VHTR fuel will be utilized as the in-pile performance validation data.

Non-destructive test for VHTR fuel using 160kV X-ray system in Hotcell

International Nuclear Information System (INIS)

Kim, Young Jun; Yoo, Boung Ok; Choo, Yong sun; Baik Sang youl; Kim, Hee Moon; Ahn, Sang Bok

2016-01-01

The research for VHTR which is one of the next generation reactor has been actively carried out. As a part of the research for VHTR, an irradiation examination for the VHTR fuel was performed to confirm an in-pile behavior in HANARO. The non-destructive test for the irradiated fuel is very important to understand the in-pile behavior of the fuel. Especially, the X-ray system is useful to observe the fuel shape without destruction. A dimensional change and defect of the fuel can be confirmed thorough the Xray system. Also, using the 3-D software and CT technology, the fuel shape can be intuitionally observed. The 450kV and 160kV X-ray system were installed and operated in IMEF hotcell. The 160kV X-ray system relatively using a low voltage is suitable to a small scale sample. And high resolution images can be obtained. In this study, the non-destructive test for the unirradiated and irradiated VHTR fuel were performed using the 160kV X-ray system. Through these test, the possibility for the X-ray inspection of irradiated fuel was confirmed. The non-destructive test for the unirradiated and irradiated VHTR fuel were performed using the 160kV X-ray system. The clear images of the irradiated coated particle were produced without the radiation damage during the Xray inspection. The X-ray images of the VHTR fuel will be utilized as the in-pile performance validation data.

SINEX: SCALE shielding analysis GUI for X-Windows

International Nuclear Information System (INIS)

Browman, S.M.; Barnett, D.L.

1997-12-01

SINEX (SCALE Interface Environment for X-windows) is an X-Windows graphical user interface (GUI), that is being developed for performing SCALE radiation shielding analyses. SINEX enables the user to generate input for the SAS4/MORSE and QADS/QAD-CGGP shielding analysis sequences in SCALE. The code features will facilitate the use of both analytical sequences with a minimum of additional user input. Included in SINEX is the capability to check the geometry model by generating two-dimensional (2-D) color plots of the geometry model using a new version of the SCALE module, PICTURE. The most sophisticated feature, however, is the 2-D visualization display that provides a graphical representation on screen as the user builds a geometry model. This capability to interactively build a model will significantly increase user productivity and reduce user errors. SINEX will perform extensive error checking and will allow users to execute SCALE directly from the GUI. The interface will also provide direct on-line access to the SCALE manual

Image annotation under X Windows

Science.gov (United States)

Pothier, Steven

1991-08-01

A mechanism for attaching graphic and overlay annotation to multiple bits/pixel imagery while providing levels of performance approaching that of native mode graphics systems is presented. This mechanism isolates programming complexity from the application programmer through software encapsulation under the X Window System. It ensures display accuracy throughout operations on the imagery and annotation including zooms, pans, and modifications of the annotation. Trade-offs that affect speed of display, consumption of memory, and system functionality are explored. The use of resource files to tune the display system is discussed. The mechanism makes use of an abstraction consisting of four parts; a graphics overlay, a dithered overlay, an image overly, and a physical display window. Data structures are maintained that retain the distinction between the four parts so that they can be modified independently, providing system flexibility. A unique technique for associating user color preferences with annotation is introduced. An interface that allows interactive modification of the mapping between image value and color is discussed. A procedure that provides for the colorization of imagery on 8-bit display systems using pixel dithering is explained. Finally, the application of annotation mechanisms to various applications is discussed.

Thermo-mechanical failure criteria for x-ray windows and filters and comparison with experiments

International Nuclear Information System (INIS)

Wang, Z.; Kuzay, T.M.

1993-01-01

Synchrotron x-ray windows are vacuum separators and are usually made of thin beryllium metal. Filters are provided upstream of the window to filter out the soft x-rays to protect the window from overheating and failing. The filters are made of thin carbon products or sometimes beryllium, the same material as the window. Because the window is a vacuum separator, understanding its potential structural failure under thermal load is very important. Current structural failure models for the brazed windows and filters under thermal stresses are not very accurate. Existing models have been carefully examined and found to be inconsistent with the actual failure modes of windows tested. Due to the thinness of the filter/window, the most likely failure mode is thermal buckling. In fact, recent synchrotron tests conducted in Japan on window failures bear out this position. In this paper, failure criteria for filters/windows are proposed, and analyses are performed and compared with the experimental results from various sources. A consistent result is found between the analysis and reported experiments. A series of additional analyses based on the proposed failure criteria is also carried out for filter and window designs for the third generation synchrotron beamline front ends. Comparative results are presented here

Thermal, structural, and fabrication aspects of diamond windows for high power synchrotron x-ray beamlines

International Nuclear Information System (INIS)

Khounsary, A.M.; Phillips, W.

1992-01-01

Recent advances in chemical vapor deposition (CVD) technology have made it possible to produce thin free-standing diamond foils that can be used as the window material in high heat load, synchrotron beamlines. Numerical simulations suggest that these windows can offer an attractive and at times the only altemative to beryllium windows for use in third generation x-ray synchrotron radiation beamlines. Utilization, design, and fabrication aspects of diamond windows for high heat load x-ray beamlines are discussed, as are the microstructure characteristics bearing on diamond's performance in this role. Analytic and numerical results are also presented to provide a basis for the design and testing of such windows

Interferometric and optical tests of water window imaging x ray microscopes

Science.gov (United States)

Johnson, R. Barry

1993-01-01

Interferometric tests of Schwarzchild X-ray Microscope are performed to evaluate the optical properties and alignment of the components. Photographic measurements of the spatial resolution, focal properties, and vignetting characteristics of the prototype Water Window Imaging X-ray Microscope are made and analyzed.

120 YEARS SINCE THE DISCOVERY OF X-RAYS.

Science.gov (United States)

Babic, Rade R; Stankovic Babic, Gordana; Babic, Strahinja R; Babic, Nevena R

2016-09-01

This paper is intended to celebrate the 120th anniversary of the discovery of X-rays. X-rays (Roentgen-rays) were discovered on the 8th ofNovember, 1895 by the German physicist Wilhelm Conrad Roentgen. Fifty days after the discovery of X-ray, on December 28, 1895. Wilhelm Conrad Roentgen published a paper about the discovery of X-rays - "On a new kind of rays" (Wilhelm Conrad Roentgen: Ober eine neue Art von Strahlen. In: Sitzungsberichte der Wurzburger Physik.-Medic.- Gesellschaft. 1895.). Therefore, the date of 28th ofDecember, 1895 was taken as the date of X-rays discovery. This paper describes the work of Wilhelm Conrad Roentgen, Nikola Tesla, Mihajlo Pupin and Maria Sklodowska-Curie about the nature of X-rays . The fantastic four - Wilhelm Conrad Roentgen, NikolaTesla, Mihajlo ldvorski Pupin and Maria Sklodowska-Curie set the foundation of radiology with their discovery and study of X-rays. Five years after the discovery of X-rays, in 1900, Dr Avram Vinaver had the first X-ray machine installed in abac, in Serbia at the time when many developed countries did not have an X-ray machine and thus set the foundation of radiology in Serbia.

12-inch x-ray image intensifier with thin metal input window

Energy Technology Data Exchange (ETDEWEB)

Obata, Yoshiharu; Anno, Hidero; Harao, Norio [Toshiba Corp., Kawasaki, Kanagawa (Japan)

1982-08-01

Borosilicate glass has been used for X-ray input window of image intensifiers (I.I.) up to now. Now two new types of 12-inch metal I.I., RT12301C and RT12302C, have been developed. They use convex 1-mm aluminum (instead of 5-mm borosilicate glass) for the input window. Adopting a high-performance penta-electronic lens and a new type of light guide CsI film, these intensifiers have greatly improved contrast, quantum detection efficiency (QDE) and resolution capability. In spite of low dosage, image quality equivalent to that in the conventional direct radiograph is obtained through combined use of the new-type 12-inch metal I.I. with 0.3-mm small-focal-spot X-ray tube. Great contribution to digital radiography is expected of this I.I.

Development of Calcomp compatible interface library 'piflib' on X Window System

International Nuclear Information System (INIS)

Tanabe, Hidenobu; Yokokawa, Mitsuo; Onuma, Yoshio.

1993-05-01

Graphics processing at JAERI mainly has been executed on mainframe computers with Calcomp compatible graphics libraries. With spread of engineering workstations (EWS), it is important that those enormous graphics softwares be able to be carried out on EWS. The Calcomp compatible interface library 'piflib' has been developed on the X Window System, which is the most popular window environments on EWS. In this report, specifications of the library 'piflib' and its usages are presented. The cooperative processing with mainframe computers is also described. (author)

Window observers for linear systems

Directory of Open Access Journals (Sweden)

Utkin Vadim

2000-01-01

Full Text Available Given a linear system x ˙ = A x + B u with output y = C x and a window function ω ( t , i.e., ∀ t , ω ( t ∈ {0,1 }, and assuming that the window function is Lebesgue measurable, we refer to the following observer, x ˆ = A x + B u + ω ( t L C ( x − x ˆ as a window observer. The stability issue is treated in this paper. It is proven that for linear time-invariant systems, the window observer can be stabilized by an appropriate design under a very mild condition on the window functions, albeit for linear time-varying system, some regularity of the window functions is required to achieve observer designs with the asymptotic stability. The corresponding design methods are developed. An example is included to illustrate the possible applications

Beryllium window flange for synchrotron radiation X-ray beamline fabricated by hot isostatic press method

International Nuclear Information System (INIS)

Asaoka, Seiji; Maezawa, Hideki; Nishida, Kiyotoshi; Sakamoto, Naoki.

1995-01-01

The synchrotron radiation experimental facilities in National Laboratory for High Energy Physics are the experimental facilities for joint utilization, that possess the positron storage ring of 2.5 GeV exclusively used for synchrotron radiation. Synchrotron radiation is led through a mainstay beam channel to the laboratory, and in the beam line of X-ray, it is used for experiment through the taking-out window made of beryllium. At this time, the function of the taking-out window is to shut off between the ultrahigh vacuum in the mainstay beam channel and the atmosphere, and to cut the low energy component of synchrotron radiation spectra. The experiment using X-ray is carried out mostly in the atmosphere. The design of the efficient cooling water channel which is compatible with the flange construction is important under the high thermal load of synchrotron radiation. The beryllium window flange for synchrotron radiation X-ray was made by HIP method, and the ultrahigh vacuum test, the high pressure water flow test and the actual machine test were carried out by heat cycle. The properties required for the window material, the requirement of the construction, the new development of HIP method, and the experiments for evaluating the manufactured beryllium window are described. (K.I.)

Sputtered carbon as a corrosion barrier for x-ray detector windows

Energy Technology Data Exchange (ETDEWEB)

Rowley, Joseph; Pei, Lei; Davis, Robert C., E-mail: davis@byu.edu; Vanfleet, Richard R. [Department of Physics and Astronomy, Brigham Young University, Provo, Utah 84602 (United States); Liddiard, Steven; Harker, Mallorie; Abbott, Jonathan [Moxtek, Inc., 452 W 1260 N, Orem, Utah 84057 (United States)

2016-09-15

Sputtered amorphous carbon thin films were explored as corrosion resistant coatings on aluminum thin films to be incorporated into x-ray detector windows. The requirements for this application include high corrosion resistance, low intrinsic stress, high strains at failure, and high x-ray transmission. Low temperature sputtering was used because of its compatibility with the rest of the window fabrication process. Corrosion resistance was tested by exposure of carbon coated and uncoated Al thin films to humidity. Substrate curvature and bulge testing measurements were used to determine intrinsic stress and ultimate strain at failure. The composition and bonding of the carbon films were further characterized by electron energy loss spectroscopy, Raman spectroscopy, and carbon, hydrogen, and nitrogen elemental analyses. Samples had low compressive stress (down to.08 GPa), a high strain at failure (3%), and a low fraction of sp{sup 3} carbon–carbon bonds (less than 5%). The high breaking strain and excellent x-ray transmission of these sputtered carbon films indicate that they will work well as corrosion barriers in this application.

Ultrasound-guided identification of cardiac imaging windows.

Science.gov (United States)

Liu, Garry; Qi, Xiu-Ling; Robert, Normand; Dick, Alexander J; Wright, Graham A

2012-06-01

Currently, the use of cine magnetic resonance imaging (MRI) to identify cardiac quiescent periods relative to the electrocardiogram (ECG) signal is insufficient for producing submillimeter-resolution coronary MR angiography (MRA) images. In this work, the authors perform a time series comparison between tissue Doppler echocardiograms of the interventricular septum (IVS) and concurrent biplane x-ray angiograms. Our results indicate very close agreement between the diastasis gating windows identified by both the IVS and x-ray techniques. Seven cath lab patients undergoing diagnostic angiograms were simultaneously scanned during a breath hold by ultrasound and biplane x-ray for six to eight heartbeats. The heart rate of each patient was stable. Dye was injected into either the left or right-coronary vasculature. The IVS was imaged using color tissue Doppler in an apical four-chamber view. Diastasis was estimated on the IVS velocity curve. On the biplane angiograms, proximal, mid, and distal regions were identified on the coronary artery (CA). Frame by frame correlation was used to derive displacement, and then velocity, for each region. The quiescent periods for a CA and its subsegments were estimated based on velocity. Using Pearson's correlation coefficient and Bland-Altman analysis, the authors compared the start and end times of the diastasis windows as estimated from the IVS and CA velocities. The authors also estimated the vessel blur across the diastasis windows of multiple sequential heartbeats of each patient. In total, 17 heartbeats were analyzed. The range of heart rate observed across patients was 47-79 beats per minute (bpm) with a mean of 57 bpm. Significant correlations (R > 0.99; p windows. The mean difference in the starting times between IVS and CA quiescent windows was -12.0 ms. The mean difference in end times between IVS and CA quiescent windows was -3.5 ms. In contrast, the correlation between RR interval and both the start and duration of the x

Windows 8 tweaks

CERN Document Server

Sinchak, Steve

2013-01-01

Acres of Windows 8 tweaks from a Microsoft MVP and creator of Tweaks.com! From a Microsoft MVP, who is also the savvy creator of Tweaks.com, comes this ultimate collection of Windows 8 workarounds. Steve Sinchak takes you way beyond default system settings, deep under the hood of Windows 8, down to the hidden gems that let you customize your Windows 8 system like you wouldn't believe. From helping you customize the appearance to setting up home networking, sharing media, and squeezing every ounce of performance out of the OS, this book delivers. Get ready to rock and roll with Wind

An X window based graphics user interface for radiation information processing system developed with object-oriented programming technology

International Nuclear Information System (INIS)

Gao Wenhuan; Fu Changqing; Kang Kejun

1993-01-01

X Window is a network-oriented and network transparent windowing system, and now dominant in the Unix domain. The object-oriented programming technology can be used to change the extensibility of a software system remarkably. An introduction to graphics user interface is given. And how to develop a graphics user interface for radiation information processing system with object-oriented programming technology, which is based on X Window and independent of application is described briefly

Tailored temperature window of CuO{sub x}/WO{sub x}–ZrO{sub 2} for NO{sub x} reduction via adjusting the calcination temperature of WO{sub x}–ZrO{sub 2}

Energy Technology Data Exchange (ETDEWEB)

Si, Zhichun, E-mail: si.zhichun@sz.tsinghua.edu.cn [Advanced Materials Institute, Graduate School at Shenzhen, Tsinghua University, Shenzhen 518055 (China); Wu, Xiaodong [State Key Laboratory of New Ceramics and Fine Process, Department of Materials Science and Engineering, Tsinghua University, Beijing 100084 (China); Yangtze Delta Region Institute of Tsinghua University, Zhejiang 314000 (China); Weng, Duan, E-mail: duanweng@tsinghua.edu.cn [State Key Laboratory of New Ceramics and Fine Process, Department of Materials Science and Engineering, Tsinghua University, Beijing 100084 (China); Ma, Ziran; Ma, Jing [State Key Laboratory of New Ceramics and Fine Process, Department of Materials Science and Engineering, Tsinghua University, Beijing 100084 (China)

2013-02-15

WO{sub x}–ZrO{sub 2} support was calcined at various temperatures for obtaining controllable activity of copper catalysts for NO{sub x} reduction by ammonia. The temperature window of copper catalyst for over 80% NO{sub x} conversion shifts from 180–300 to 230–350 °C by elevating the calcination temperature of WO{sub x}–ZrO{sub 2} support from 500 to 600 °C, due to the increased Brønsted acidity and reduced structure and electronic interactions between copper oxides and tungsten oxides arising from the polymerization of WO{sub x} clusters on surface of support. Calcining WO{sub x}–ZrO{sub 2} support at 700 °C leads to the reduced redox property of copper oxides on the Cu–O–W interface and the formation of bulk-like CuO, results in a low activity of catalyst. - Graphical abstract: The temperature window of catalyst for over 80% NO{sub x} conversion shifts from 180-300 °C to 230–350 °C by elevating the calcination temperature of WO{sub x}–ZrO{sub 2} support from 500 °C to 600 °C. Highlights: ► The temperature window of catalyst is tailored by calcining the support. ► The mechanisms of tailoring the temperature window of catalyst are discussed. ► The polymerization of WO{sub x} leads to the increased Brønsted acidity of catalysts. ► The CuO{sub x}/WO{sub x} interactions are reduced by elevating calcination temperature of support.

Development of reliable diamond window for EC launcher on fusion reactors

International Nuclear Information System (INIS)

Takahashi, K.; Illy, S.; Heidinger, R.; Kasugai, A.; Minami, R.; Sakamoto, K.; Thumm, M.; Imai, T.

2005-01-01

In order to avoid a possible accidental event of a diamond window, i.e. a leakage of cooling water into vacuum, a new diamond window with a copper (Cu)-coated edge was developed. The 0.5 mm thick Cu-coating completely covers the window disk edge and aluminum braze, between the diamond disk edge and the inconel cuffs cooled by water. Corrosion of the aluminum braze can also be prevented by the Cu-coating. A 170 GHz high power RF transmission experiment, which was indicative for a MW-level transmission, was carried out to investigate the cooling capability of the Cu-coated window. RF power/pulse length 55 kW/3.5 s and 120 kW/3 s, were transmitted through the window without any problem. Temperature increase of 50 and 100 o C were obtained, respectively. The results agree with thermal calculations with loss tangent 8.5 x 10 -4 and thermal conductivity 1.9 kW/(m K) of the diamond. Thermal and stress analysis show that no serious stress between the diamond disk and the Cu-coating is established. It concludes that a diamond window with Cu-coated edge water-cooling is capable of MW-level transmission and that the Cu-coating improves the reliability of the diamond window

A DEEP X-RAY VIEW OF THE BARE AGN ARK 120. I. REVEALING THE SOFT X-RAY LINE EMISSION

Energy Technology Data Exchange (ETDEWEB)

Reeves, J. N.; Braito, V. [Center for Space Science and Technology, University of Maryland Baltimore County, 1000 Hilltop Circle, Baltimore, MD 21250 (United States); Porquet, D. [Observatoire Astronomique de Strasbourg, Université de Strasbourg, CNRS, UMR 7550, 11 rue de l’Université, F-67000 Strasbourg (France); Nardini, E. [Astrophysics Group, School of Physical and Geographical Sciences, Keele University, Keele, Staffordshire, ST5 5BG (United Kingdom); Lobban, A. [Dept of Physics and Astronomy, University of Leicester, University Road, Leicester LE1 7RH (United Kingdom); Turner, T. J., E-mail: jreeves@umbc.edu, E-mail: j.n.reeves@keele.ac.uk [Department of Physics, University of Maryland Baltimore County, 1000 Hilltop Circle, Baltimore, MD 21250 (United States)

2016-09-10

The Seyfert 1 galaxy Ark 120 is a prototype example of the so-called class of bare nucleus active galactic nuclei (AGNs), whereby there is no known evidence for the presence of ionized gas along the direct line of sight. Here deep (>400 ks exposure), high-resolution X-ray spectroscopy of Ark 120 is presented from XMM-Newton observations that were carried out in 2014 March, together with simultaneous Chandra /High Energy Transmission Grating exposures. The high-resolution spectra confirmed the lack of intrinsic absorbing gas associated with Ark 120, with the only X-ray absorption present originating from the interstellar medium (ISM) of our own Galaxy, with a possible slight enhancement of the oxygen abundance required with respect to the expected ISM values in the solar neighborhood. However, the presence of several soft X-ray emission lines are revealed for the first time in the XMM-Newton RGS spectrum, associated with the AGN and arising from the He- and H-like ions of N, O, Ne, and Mg. The He-like line profiles of N, O, and Ne appear velocity broadened, with typical FWHMs of ∼5000 km s{sup −1}, whereas the H-like profiles are unresolved. From the clean measurement of the He-like triplets, we deduce that the broad lines arise from a gas of density n {sub e} ∼ 10{sup 11} cm{sup −3}, while the photoionization calculations infer that the emitting gas covers at least 10% of 4 π steradian. Thus the broad soft X-ray profiles appear coincident with an X-ray component of the optical–UV broad-line region on sub-parsec scales, whereas the narrow profiles originate on larger parsec scales, perhaps coincident with the AGN narrow-line region. The observations show that Ark 120 is not intrinsically bare and substantial X-ray-emitting gas exists out of our direct line of sight toward this AGN.

Displaying DIII-D plasma data using DEC's X window system

International Nuclear Information System (INIS)

Greene, K.L.

1991-11-01

The D3-D tokamak program, funded by the Department of Energy, carries out plasma physics and fusion energy research experiments. The machine began operation in February 1986; at that time, approximately 7 Mbytes of data was collected for shot. Since that time, the shot size has steadily increased to over 50 Mbytes with the average shot size between 35 and 45 Mbytes. Shots are fired every 12 to 15 minutes and last approximately 5 to 10 seconds. Between 30 and 40 shots are fired each day when plasma experiments are scheduled. In 1987 MFITD and MFITPLAY were written/modified. These two programs provide graphical output that allows the users to see, before the next shot, the plasma shape and the locations of the plasma and magnetic flux lines within the tokamak. MFITD performs the computations which calculate the shape and location of the plasma; it also graphically displays a small subset of timeslice data. MFITPLAY graphically displays the full set of timeslice data. Through interactive commands, MFITPLAY also allows the user to control the various aspects of how the data is displayed. In 1990, both programs were converted from User Interface Services (UIS) routines, which are part of the MicroVMS workstation graphics software, to DEC's X Window System using the DECWindows window manager. These modifications were required because of a move by Digital Equipment Corporation (DEC) to support X windows and phase out UIS. Due to the nature and purpose of each program, MFITD needed only simple graphics conversion while MFITPLAY was completely rewritten. The DECWindows version of MFITPLAY offers a number of improvements, such as a more intuitive user interface

Windows for Intel Macs

CERN Document Server

Ogasawara, Todd

2008-01-01

Even the most devoted Mac OS X user may need to use Windows XP, or may just be curious about XP and its applications. This Short Cut is a concise guide for OS X users who need to quickly get comfortable and become productive with Windows XP basics on their Macs. It covers: Security Networking ApplicationsMac users can easily install and use Windows thanks to Boot Camp and Parallels Desktop for Mac. Boot Camp lets an Intel-based Mac install and boot Windows XP on its own hard drive partition. Parallels Desktop for Mac uses virtualization technology to run Windows XP (or other operating systems

Windows Home Server users guide

CERN Document Server

Edney, Andrew

2008-01-01

Windows Home Server brings the idea of centralized storage, backup and computer management out of the enterprise and into the home. Windows Home Server is built for people with multiple computers at home and helps to synchronize them, keep them updated, stream media between them, and back them up centrally. Built on a similar foundation as the Microsoft server operating products, it's essentially Small Business Server for the home.This book details how to install, configure, and use Windows Home Server and explains how to connect to and manage different clients such as Windows XP, Windows Vist

Teach yourself visually Windows 10

CERN Document Server

McFedries, Paul

2015-01-01

Learn Windows 10 visually with step-by-step instructions Teach Yourself VISUALLY Windows 10 is the visual learner's guide to the latest Windows upgrade. Completely updated to cover all the latest features, this book walks you step-by-step through over 150 essential Windows tasks. Using full color screen shots and clear instruction, you'll learn your way around the interface, set up user accounts, play media files, download photos from your camera, go online, set up email, and much more. You'll even learn how to customize Windows 10 to suit the way you work best, troubleshoot and repair common

Development and experimental study of beryllium window for ITER radial X-ray camera

Energy Technology Data Exchange (ETDEWEB)

Chen, Zhaoxi [Institute of Plasma Physics, Chinese Academy of Sciences, Hefei 230031 (China); Jin, Guangxu [Materion Brush (United States); Chen, Kaiyun; Chen, Yebin; Song, Yuntao [Institute of Plasma Physics, Chinese Academy of Sciences, Hefei 230031 (China); Hu, Liqun, E-mail: lqhu@ipp.ac.cn [Institute of Plasma Physics, Chinese Academy of Sciences, Hefei 230031 (China); Niu, Luying; Sheng, Xiuli; Cheng, Yong; Lu, Kun [Institute of Plasma Physics, Chinese Academy of Sciences, Hefei 230031 (China)

2013-12-15

Highlights: • The thickness of the beryllium foil is chosen as 80 μm to guarantee its safety under high pressure differential in accident events. • Using low purity of beryllium as the transition material, the effect of thermal stress caused by diffusion bonding process can be reduced. • Sealing ring and honeycomb-like supports are designed and used in the mechanical clamped beryllium window to enhance its sealing and safety performance. • The beryllium windows have good performance under severe working conditions like high temperature baking, vibration or impact load. -- Abstract: Radial X-ray camera (RXC) is a diagnostic device planned to be installed in the ITER Equatorial Port no. 12. Beryllium window will be installed between the inner and outer camera of RXC, which severs as the transmission photocathode substrate and also the vacuum isolation component. In this paper the design and manufacture process of two types of beryllium windows were introduced. Although 50 μm thickness of beryllium foil is the best choice, the 80 μm one with X-ray threshold of 1.34 keV was selected for safety consideration. Using the intermediate layer (low purity of beryllium) between the beryllium foil and the stainless steel base flange is an effective strategy to limit the welding thermal deformation and thermal stress of the thin foil caused by bonding between different materials. By using ANSYS software, the feasibility of the aperture design was analyzed and validated. Metal sealing ring was applied in the mechanical clamped beryllium window for its good stability under high temperature and neutron radiation. Although both of the hollow metal sealing ring with 0.03 mm silver coating and the pure silver sealing ring can satisfy the sealing requirement, the later one was chosen to produce the final product. Two hours 240 °C high temperature baking test, two hours 3.3 Hz vibration test and fatigue test were performed on the two types of beryllium windows. Based on the

Rails on Windows

CERN Document Server

Hibbs, Curt

2007-01-01

It's no secret that the entire Ruby onRails core team uses OS X as their preferreddevelopment environment. Becauseof this, it is very easy to findauthoritative information on the webabout using Rails on OS X. But the truthis that Windows developers using Railsprobably outnumber those using otherplatforms. A Windows development environmentcan be just as productive asany other platform. This is a guide to developing with Rubyon Rails under Windows. It won't teachyou how to write Ruby on Rails web applications,but it will show you what toolsto use and how to set them up to createa complete Rail

X-ray contrast media-an overview

International Nuclear Information System (INIS)

Christiansen, Cathrine

2005-01-01

X-ray contrast media are chemically inert drugs which are given intravascularly in very high amounts within a very short time period. Although they are regarded as relatively safe drugs, adverse reactions can occur: these are normally divided into immediate and delayed reactions. The latter appear hours to days after injection. Immediate reactions have been drastically reduced since the introduction of non-ionic monomers and non-ionic dimers. However, the delayed reactions still occur in a frequency of 1-3% in X-ray contrast media exposed patients. The majority of these reactions are mild and manifest as skin eruption, but severe reactions can also occur. Further improvement of the safety of these drugs is only possible with a better understanding of etiologies behind the observed adverse reactions

X-ray Emission from the Radio Jet in 3C 120

DEFF Research Database (Denmark)

Harris, D. E.; Hjorth, J.; Sadun, A. C.

1999-01-01

We report the discovery of X-ray emission from a radio knot at a projected distance of 25" from the nucleus of the Seyfert galaxy, 3C 120. The data were obtained with the ROSAT High Resolution Imager (HRI). Optical upper limits for the knot preclude a simple power law extension of the radio...

Efficient 'water window' soft x-ray high-Z plasma source

International Nuclear Information System (INIS)

Higashiguchi, T; Otsuka, T; Jiang, W; Endo, A; Li, B; Dunne, P; O'Sullivan, G

2013-01-01

Unresolved transition array (UTA) is scalable to shorter wavelengths, and we demonstrate a table-top broadband emission 'water window' soft x-ray source based on laser-produced plasmas. Resonance emission from multiply charged ions merges to produce intense UTAs in the 2 to 4 nm region, extending below the carbon K edge (4.37 nm). An outline of a microscope design for single-shot live cell imaging is proposed based on a bismuth (Bi) plasma UTA source, coupled to multilayer mirror optics

Development of data acquisition and processing software based on MS-Windows 3.X for safeguards

International Nuclear Information System (INIS)

Tan Yajun

1996-01-01

The development method of data acquisition and processing software based on MS-Windows 3.X for safeguards is presented. The paper describes the design methods of graphical user interface (GUI), multiwindow and multitask-based spectrum graph display, data acquisition and processing and the application of object-oriented programming (OOP). Using the package, an effective prototype design path can be found for MS-Windows-based software. The methods and programs have been applied in some safeguard non-destructive assay system

Digitization of medical documents: an X-Windows application for fast scanning.

Science.gov (United States)

Muñoz, A; Salvador, C H; Gonzalez, M A; Dueñas, A

1992-01-01

This paper deals with digitization, using a commercial scanner, of medical documents as still images for introduction into a computer-based Information System. Document management involves storing, editing and transmission. This task has usually been approached from the perspective of the difficulties posed by radiologic images because of their indisputable qualitative and quantitative significance. However, healthcare activities require the management of many other types of documents and involve the requirements of numerous users. One key to document management will be the availability of a digitizer to deal with the greatest possible number of different types of documents. This paper describes the relevant aspects of documents and the technical specifications that digitizers must fulfill. The concept of document type is introduced as the ideal set of digitizing parameters for a given document. The use of document type parameters can drastically reduce the time the user spends in scanning sessions. Presentation is made of an application based on Unix, X-Windows and OSF/Motif, with a GPIB interface, implemented around the document type concept. Finally, the results of the evaluation of the application are presented, focusing on the user interface, as well as on the viewing of color images in an X-Windows environment and the use of lossy algorithms in the compression of medical images.

The effects of X window HEP graphics applications on ESnet

International Nuclear Information System (INIS)

Abar, F.A.; Lidinsky, W.P.

1994-01-01

Wide area networking is the next evolutionary step toward distributed computing. Many applications that were found useful in local area networks are beginning to show their presence in wide area networks (WANs). A question is: Given today's typical WAN infrastructure, what are the effects of the presence of distributed applications in the WANs and what can be done to facilitate full deployment of such services across wide area network? A simulation model for X window distributed graphical applications in high energy physics communities interacting across the DOE Energy Science wide area networks (ESnet) was created to examine X service resource requirements and ESnet resource limitations. Through simulation analysis the effects of the incremental introduction of X traffic to ESnet was determined as was the load level at which ESnet became unstable. Proposals for improving ESnet performance by upgrading to T3 links and also by introducing a service-based packet priority scheme at the network layer were also examined

Windows 8.1 for dummies

CERN Document Server

Rathbone, Andy

2013-01-01

The bestselling book on Windows, now updated for the new 8.1 features Microsoft has fine-tuned Windows 8 with some important new features, and veteran author Andy Rathbone explains every one in this all-new edition of a long-time bestseller. Whether you're using Windows for the first time, upgrading from an older version, or just moving from Windows 8 to 8.1, here's what you need to know. Learn about the dual interfaces, the new Start button, how to customize the interface and boot operations, and how to work with programs and files, use the web and social media, manage music and photos, and

30 CFR 62.160 - Hearing protectors.

Science.gov (United States)

2010-07-01

... REGULATIONS OCCUPATIONAL NOISE EXPOSURE § 62.160 Hearing protectors. (a) A mine operator must provide a hearing protector to a miner whose noise exposure equals or exceeds the action level under § 62.120 of this part. In addition, the mine operator must: (1) Train the miner in accordance with § 62.180 of this...

Searching for O-X-B mode-conversion window with monitoring of stray microwave radiation in LHD

International Nuclear Information System (INIS)

Igami, H.; Kubo, S.; Laqua, H. P.; Nagasaki, K.; Inagaki, S.; Notake, T.; Shimozuma, T.; Yoshimura, Y.; Mutoh, T.; LHD Experimental Group

2006-01-01

In the Large Helical Device, the stray microwave radiation is monitored by using so-called sniffer probes during electron cyclotron heating. In monitoring the stray radiation, we changed the microwave beam injection angle and search the O-X-B mode-conversion window to excite electron Bernstein waves (EBWs). When the microwave beam is injected toward the vicinity of the predicted O-X-B mode-conversion window, the electron temperature rises in the central part of overdense plasmas. In that case, the stray radiation level near the injection antenna becomes low. These results indicate that monitoring the stray radiation near the injection antenna is helpful in confirming the effectiveness of excitation of EBWs simply without precise analysis

A buffer-layer/a-SiO{sub x}:H(p) window-layer optimization for thin film amorphous silicon based solar cells

Energy Technology Data Exchange (ETDEWEB)

Park, Jinjoo; Dao, Vinh Ai [College of Information and Communication Engineering, Sungkyunkwan University, Suwon 440-746 (Korea, Republic of); Shin, Chonghoon [Department of Energy Science, Sungkyunkwan University, Suwon 440-746 (Korea, Republic of); Park, Hyeongsik [College of Information and Communication Engineering, Sungkyunkwan University, Suwon 440-746 (Korea, Republic of); Kim, Minbum; Jung, Junhee [Department of Energy Science, Sungkyunkwan University, Suwon 440-746 (Korea, Republic of); Kim, Doyoung [School of Electricity and Electronics, Ulsan College West Campus, Ulsan 680-749 (Korea, Republic of); Yi, Junsin, E-mail: yi@yurim.skku.ac.kr [College of Information and Communication Engineering, Sungkyunkwan University, Suwon 440-746 (Korea, Republic of); Department of Energy Science, Sungkyunkwan University, Suwon 440-746 (Korea, Republic of)

2013-11-01

Amorphous silicon based (a-Si:H-based) solar cells with a buffer-layer/boron doped hydrogenated amorphous silicon oxide (a-SiO{sub x}:H(p)) window-layer were fabricated and investigated. In the first part, in order to reduce the Schottky barrier height at the fluorine doped tin oxide (FTO)/a-SiO{sub x}:H(p) window-layer heterointerface, we have used buffer-layer/a-SiO{sub x}:H(p) for the window-layer, in which boron doped hydrogenated amorphous silicon (a-Si:H(p)) or boron doped microcrystalline silicon (μc-Si:H(p)) is introduced as a buffer layer between the a-SiO{sub x}:H(p) and FTO of the a-Si:H-based solar cells. The a-Si:H-based solar cell using a μc-Si:H(p) buffer-layer shows the highest efficiency compared to the optimized bufferless, and a-Si:H(p) buffer-layer in the a-Si:H-based solar cells. This highest performance was attributed not only to the lower absorption of the μc-Si:H(p) buffer-layer but also to the lower Schottky barrier height at the FTO/window-layer interface. Then, we present the dependence of the built-in potential (V{sub bi}) and blue response of the devices on the inversion of activation energy (ξ) of the a-SiO{sub x}:H(p), in the μc-Si:H(p)/a-SiO{sub x}:H(p) window-layer. The enhancement of both V{sub bi} and blue response is observed, by increasing the value of ξ. The improvement of V{sub bi} and blue response can be ascribed to the enlargement of the optical gap of a-SiO{sub x}:H(p) films in the μc-Si:H(p)/a-SiO{sub x}:H(p) window-layer. Finally, the conversion efficiency was increased by 22.0%, by employing μc-Si:H(p) as a buffer-layer and raising the ξ of the a-SiO{sub x}:H(p), compared to the optimized bufferless case, with a 10 nm-thick a-SiO{sub x}:H(p) window-layer. - Highlights: • Low Schottky barrier height benefits fill factor, and open-circuit voltage (V{sub oc}). • High band gap is beneficial for short-circuit current density (J{sub sc}). • Boron doped microcrystalline silicon is a suitable buffer-layer for

Postbuckling behavior of windows subjected to synchrotron radiation x-rays

International Nuclear Information System (INIS)

Wang, Z.; Kuzay, T.M.; Sharma, S.K.

1993-01-01

Analyses performed on two Be windows (250 and 100 μm thick) show that the additional postbuckling strength still exists after initial window buckling and this part can be used by a thin window design in the working stage. However, the load factor to complate failure is not as big as the load factor to failure of a uniformly compressed window (the case for a thick window where buckling stress is larger than yielding stress of the window material). That is, the load factor of a thin window to collapse is not as large as that of a thick window without buckling. Hence, unless there is a special need for a thin window, buckling of the windows in normal working stage should not be recommended. Although shakedown was not considered, a similar conclusion can be expected for that case

Marketing through Social Media : Case: Comparison of Social Media Marketing Approaches of B2C Companies for Company X

OpenAIRE

Rantapelkonen Ahlberg, Jaana

2010-01-01

Rantapelkonen Ahlberg, Jaana. 2010. Social Media Marketing. Case: Comparison of Social Media Marketing Approaches of B2C Companies for Company X. Master’s Thesis. Kemi-Tornio University of Applied Sciences. Business and Culture. Pages 42 (74). The objective of this thesis is to provide insights on how Company X can use Social Media as a marketing and branding tool in consumer marketing in the Swedish market. More specifically, this study attempts to define what kinds of social media are u...

Peliohjelmointi Windows Phone 8:lle

OpenAIRE

Bäckström, Toni

2014-01-01

Tässä insinöörityössä tutustutaan Windows Phone 8 -mobiilikäyttöjärjestelmään peliohjelmoijan näkökulmasta. Työn tavoitteena oli erityisesti esitellä Microsoftin itse kehittämiä XNA- ja DirectX-peliohjelmointikirjastoja teoriassa ja käytännössä. Työn aluksi käydään läpi hieman Windows Phonen historiaa ja yleisesti kehittämistä Windows Phone 8:lle. Tämän jälkeen luodaan katsaus Windows Phone 8:aan pelialustana. Työn suurin osuus on XNA:n ja DirectX:n esittely teoriassa; kummastakin men...

22 CFR 120.9 - Defense service.

Science.gov (United States)

2010-04-01

... 22 Foreign Relations 1 2010-04-01 2010-04-01 false Defense service. 120.9 Section 120.9 Foreign... Defense service. (a) Defense service means: (1) The furnishing of assistance (including training) to..., educational, or information publications and media of all kinds, training aid, orientation, training exercise...

X-ray optical analyses with X-Ray Absorption Package (XRAP)

International Nuclear Information System (INIS)

Wang, Zhibi; Kuzay, T.M.; Dejus, R.; Grace, T.

1994-01-01

This paper presents an X-Ray Absorption Package (XRAP) and the theoretical background for this program. XRAP is a computer code developed for analysis of optical elements in synchrotron radiation facilities. Two main issues are to be addressed: (1) generating BM (bending magnet) and ID (insertion device) spectrum and calculating their absorption in media, especially in such structural forms as variable thickness windows/filters and crystals; and (2) providing a finite difference engine for fast but sophisticated thermal and stress analyses for optical elements, such as windows and filters. Radiation cooling, temperature-dependent material properties (such as thermal conductivity and thermal expansion coefficient) etc. are taken into account in the analyses. For very complex geometry, an interface is provided directly to finite element codes such as ANSYS. Some of the present features built into XRAP include: (1) generation of BM and ID spectra; (2) photon absorption analysis of optical elements including filters, windows and mirrors, etc.; (3) heat transfer and thermal stress analyses of windows and filters and their buckling check; (4) user-friendly graphical-interface that is based on the state-of-the-art technology of GUI and X-window systems, which can be easily ported to other computer platforms; (5) postscript file output of either black/white or colored graphics for total/absorbed power, temperature, stress, spectra, etc

Exploiting the X-Window environment to expand the number, reach, and usefulness of Fermilab accelerator control consoles

International Nuclear Information System (INIS)

Cahill, K.; Smedinghoff, J.

1992-01-01

The Fermilab accelerator operator workstation of choice is now the Digital VAX station running VMS and X-Window software. This new platform provides an easy to learn programming environment while support routines are expanding in number and power. The X-Window environment is exploited to provide remote consoles to users across long haul networks and to support multiple consoles on a single workstation. The integration of imaging systems, local datalogging, commercial and Physics community's software, and development facilities on the operator workstation adds functionality to the system. The locally engineered knob/pointer/keyboard interface solves the multiple keyboard and mouse problems of a multi-screen console. This paper will address these issues of Fermilab's accelerator operator workstations. (author)

PENGARUH KREATIVITAS BELAJAR, PENGGUNAAN MEDIA PEMBELAJARAN POWER POINT, DAN LINGKUNGAN KELUARGA TERHADAP HASIL BELAJAR MATA PELAJARAN AKUNTANSI PADA SISWA KELAS X AKT SMK NEGERI 2 BLORA TAHUN AJARAN 2012/2013 (MOTIVASI BELAJAR SEBAGAI VARIABEL INTERVE

Directory of Open Access Journals (Sweden)

Chandra Putri

2016-03-01

Full Text Available Penelitian ini bertujuan untuk mengetahui pengaruh kreativitas belajar, penggunaan media pembelajaran power point, dan lingkungan keluarga terhadap hasil belajar melalui motivasi belajar siswa kelas X AKT SMK Negeri 2 Blora Tahun Ajaran 2012/2013. Populasi dalam penelitian ini adalah seluruh siswa kelas X AKT SMK Negeri 2 Blora Tahun Ajaran 2012/2013 sejumlah 120 siswa. Metode pengumpulan data: dokumentasi, angket. Metode analisis data yaitu analisis deskriptif, analisis konfirmatori, dan analisis Structural Equation Modeling (SEM. Hasil penelitian menunjukkan bahwa ada pengaruh positif dan signifikan antara kreativitas belajar, penggunaan media pembelajaran power point, dan lingkungan keluarga motivasi belajar; adanya pengaruh langsung dan tidak langsung antara kreativitas belajar, penggunaan media pembelajaran power point, dan lingkungan keluarga terhadap hasil belajar. This study has a purpose to find out the effect of learning creativity, the using of power point as a learning media, and family environment toward to learning result through learning motivation of the student of class X AKT SMK Negeri 2Blora year 2012/2013.The population of this study are all the student of grade X AKT SMK negri 2 blora year 2012/2013, (120.The method of gathering the data : documentation, questionnaire. The method of analyzing data: descriptive analyzing, confirmatory analyzing, and structural equation modeling (SEM analysing. The result of this study show that there is a significant positif effect and significant among the creativity of learning, the using of power point as a learning media, and family condition according to the study result through learning motivation; The results of studies using SEM analysis showed that there is a direct and the indirect influence of learning creativity, the using of power point as a learning media, and family environment toward to learning result.

Displaying DIII-D plasma data using DEC's X window system

International Nuclear Information System (INIS)

Greene, K.L.

1992-01-01

This paper reports on the DIII-D tokamak program funded by the Department of Energy, which carries out plasma physics and fusion energy research experiments. The machine began operation in February 1986; at that time, approximately 7 Mbytes of data was collected for each shot. Since that time, the shot size has steadily increased to over 50 Mbytes with the average shot size between 35 and 45 Mbytes. Shots are fired every 12 to 15 minutes and last approximately 5 to 10 seconds. Between 30 and 40 shots are fired each day when plasma experiments are scheduled. In 1990, both programs were converted from User Interface Services (UIS) routines, which are part of the MicroVMS workstation graphics software, to DEC's X Window System using the DECWindows window manager. These modifications were required because of a move by Digital Equipment Corporation (DEC) to support Xwindows and phase out UIS. Due to the nature and purpose of each program, MFITD needed only simple graphics conversion while MFITPLAY was completely rewritten. The DECWindows version of MFITPLAY offers a number of improvements, such as a more intuitive user interface

Windows 95 Beslutningsguide

DEFF Research Database (Denmark)

Sørensen, Jens Otto

1996-01-01

Mange virksomheder der bruger pc'er står netop nu over for valget: Skal vi fortsætte med DOS/Windows 3.x som operativsystem, eller skal vi skifte til efterfølgeren Windows 95? Skal vi/kan vi skifte successivt, eller skal det være en "alt eller intet beslutning". Hvornår er det rigtige tidspunkt...... at skifte? Denne artikel vil forsøge at give en baggrundsviden om Windows 95, der kan hjælpe virksomhederne igennem denne beslutningsfase....

Single-sided natural ventilation through a centre-pivot roof window

DEFF Research Database (Denmark)

Iqbal, Ahsan; Nielsen, Peter V.; Gunner, Amalie

2014-01-01

The characteristics of centre pivot roof windows for wind driven single-sided ventilation has not been studied before. These types of windows are dominating roof windows in Europe. Knowledge of flow characteristics of this kind of window is essential for accurate designing of natural ventilation...... systems. In this study, numerical methods were used to characterise a centre-pivot roof window for wind-driven single-sided ventilation. A 1:20 scale model house of the Energy Flex House (Denmark) was used in this study. The roof slope was 36o. It was found that the single-sided ventilation through...

Teach yourself visually Windows 8

CERN Document Server

McFedries, Paul

2012-01-01

A practical guide for visual learners eager to get started with Windows 8 If you learn more quickly when you can see how things are done, this Visual guide is the easiest way to get up and running on Windows 8. It covers more than 150 essential Windows tasks, using full-color screen shots and step-by-step instructions to show you just what to do. Learn your way around the interface and how to install programs, set up user accounts, play music and other media files, download photos from your digital camera, go online, set up and secure an e-mail account, and much more. The tried-and-true format

Laboratory-size three-dimensional x-ray microscope with Wolter type I mirror optics and an electron-impact water window x-ray source

Energy Technology Data Exchange (ETDEWEB)

Ohsuka, Shinji, E-mail: ohsuka@crl.hpk.co.jp [Hamamatsu Photonics K.K., 5000 Hirakuchi, Hamakita-ku, Hamamatsu-City, 434-8601 (Japan); The Graduate School for the Creation of New Photonics Industries, 1955-1 Kurematsu-cho, Nishi-ku, Hamamatsu-City, 431-1202 (Japan); Ohba, Akira; Onoda, Shinobu; Nakamoto, Katsuhiro [Hamamatsu Photonics K.K., 5000 Hirakuchi, Hamakita-ku, Hamamatsu-City, 434-8601 (Japan); Nakano, Tomoyasu [Hamamatsu Photonics K.K., 5000 Hirakuchi, Hamakita-ku, Hamamatsu-City, 434-8601 (Japan); Ray-Focus Co. Ltd., 6009 Shinpara, Hamakita-ku, Hamamatsu-City, 434-0003 (Japan); Miyoshi, Motosuke; Soda, Keita; Hamakubo, Takao [Research Center for Advanced Science and Technology, The University of Tokyo, 4-6-1 Komaba, Meguro-ku, Tokyo 153-8904 (Japan)

2014-09-15

We constructed a laboratory-size three-dimensional water window x-ray microscope that combines wide-field transmission x-ray microscopy with tomographic reconstruction techniques, and observed bio-medical samples to evaluate its applicability to life science research fields. It consists of a condenser and an objective grazing incidence Wolter type I mirror, an electron-impact type oxygen Kα x-ray source, and a back-illuminated CCD for x-ray imaging. A spatial resolution limit of around 1.0 line pairs per micrometer was obtained for two-dimensional transmission images, and 1-μm scale three-dimensional fine structures were resolved.

Laboratory-size three-dimensional x-ray microscope with Wolter type I mirror optics and an electron-impact water window x-ray source.

Science.gov (United States)

Ohsuka, Shinji; Ohba, Akira; Onoda, Shinobu; Nakamoto, Katsuhiro; Nakano, Tomoyasu; Miyoshi, Motosuke; Soda, Keita; Hamakubo, Takao

2014-09-01

We constructed a laboratory-size three-dimensional water window x-ray microscope that combines wide-field transmission x-ray microscopy with tomographic reconstruction techniques, and observed bio-medical samples to evaluate its applicability to life science research fields. It consists of a condenser and an objective grazing incidence Wolter type I mirror, an electron-impact type oxygen Kα x-ray source, and a back-illuminated CCD for x-ray imaging. A spatial resolution limit of around 1.0 line pairs per micrometer was obtained for two-dimensional transmission images, and 1-μm scale three-dimensional fine structures were resolved.

Effect of X-ray Contrast Media, Chlorination, and Chloramination on Zebrafish Development

Science.gov (United States)

Effect of X-ray Contrast Media, Chlorination, and Chloramination on Zebrafish Development Little is known about the vertebrate developmental toxicity of chlorinated or chloraminated drinking water (DW), iodinated X-ray contrast media (ICM, a common contaminate of DW) or how the c...

Development of C-band High-Power Mix-Mode RF Window

CERN Document Server

Michizono, S; Matsumoto, T; Nakao, K; Takenaka, T

2004-01-01

High power c-band (5712 MHz) rf system (40 MW, 2 μs, 50 Hz) is under consideration for the electron-linac upgrade aimed for the super KEKB project. An rf window, which isolates the vacuum and pass the rf power, is one of the most important components for the rf system. The window consists of a ceramic disk and a pill-box housing. The mix-mode rf window is designed so as to decrease the electric field on the periphery of the ceramic disk. A resonant ring is assembled in order to examine the high-power transmission test. The window was tested up to the transmission power of 160 MW. The rf losses are also measured during the rf operation.

XUIMS the X-Window User Interface Management System at CERN

CERN Document Server

Van den Eynden, M

1995-01-01

The CERN X-Window User Interface Management System (XUIMS) is a modular and highly configurable software development environment allowing the interactive design, prototyping, and production of OSF/Motif Human Computer Interfaces (HCI). Fully compliant with the X11R5 and OSF/Motif industry standards, XUIMS covers complex software areas like the development of schematics, the visualization and on-line interactions with 2D and 3D scientific data, the display of relational database data, and the direct access to CERN SPS and LEP accelerators equipment. The guarantee of consistency across the applications and the encapsulation of complex functionality in re-usable and user-friendly components has also been implemented through the development of home made graphical objects (widgets) and templates. The XUIMS environment is built with commercial software products integrated in the CERN SPS and LEP controls infrastructure with a very limited home-made effort. Productivity and quality have been improved through less co...

Computerized tomography magnified bone windows are superior to standard soft tissue windows for accurate measurement of stone size: an in vitro and clinical study.

Science.gov (United States)

Eisner, Brian H; Kambadakone, Avinash; Monga, Manoj; Anderson, James K; Thoreson, Andrew A; Lee, Hang; Dretler, Stephen P; Sahani, Dushyant V

2009-04-01

We determined the most accurate method of measuring urinary stones on computerized tomography. For the in vitro portion of the study 24 calculi, including 12 calcium oxalate monohydrate and 12 uric acid stones, that had been previously collected at our clinic were measured manually with hand calipers as the gold standard measurement. The calculi were then embedded into human kidney-sized potatoes and scanned using 64-slice multidetector computerized tomography. Computerized tomography measurements were performed at 4 window settings, including standard soft tissue windows (window width-320 and window length-50), standard bone windows (window width-1120 and window length-300), 5.13x magnified soft tissue windows and 5.13x magnified bone windows. Maximum stone dimensions were recorded. For the in vivo portion of the study 41 patients with distal ureteral stones who underwent noncontrast computerized tomography and subsequently spontaneously passed the stones were analyzed. All analyzed stones were 100% calcium oxalate monohydrate or mixed, calcium based stones. Stones were prospectively collected at the clinic and the largest diameter was measured with digital calipers as the gold standard. This was compared to computerized tomography measurements using 4.0x magnified soft tissue windows and 4.0x magnified bone windows. Statistical comparisons were performed using Pearson's correlation and paired t test. In the in vitro portion of the study the most accurate measurements were obtained using 5.13x magnified bone windows with a mean 0.13 mm difference from caliper measurement (p = 0.6). Measurements performed in the soft tissue window with and without magnification, and in the bone window without magnification were significantly different from hand caliper measurements (mean difference 1.2, 1.9 and 1.4 mm, p = 0.003, window settings with magnification. For uric acid calculi the measurement error was observed only in standard soft tissue window settings. In vivo 4.0x

Indium doped Cd{sub 1-x}Zn{sub x}O alloys as wide window transparent conductors

Energy Technology Data Exchange (ETDEWEB)

Zhu, Wei [Materials Sciences Division, Lawrence Berkeley National Laboratory, Berkeley, California 94720 (United States); Department of Physics, The Center for Physical Experiments, University of Science and Technology of China, Hefei, Anhui 230026 (China); Yu, Kin Man, E-mail: kinmanyu@cityu.edu.hk [Materials Sciences Division, Lawrence Berkeley National Laboratory, Berkeley, California 94720 (United States); Department of Physics and Materials Science, City University of Hong Kong, Kowloon (Hong Kong); Walukiewicz, W. [Materials Sciences Division, Lawrence Berkeley National Laboratory, Berkeley, California 94720 (United States)

2015-12-31

We have synthesized Indium doped Cd{sub 1-x}Zn{sub x}O alloys across the full composition range using magnetron sputtering method. The crystallographic structure of these alloys changes from rocksalt (RS) to wurtzite (WZ) when the Zn content is higher than 30%. The rocksalt phase alloys in the composition range 0 < x < 0.3 can be efficiently n-type doped, shifting the absorption edge to 3.25 eV and reducing resistivity to about 2.0 × 10{sup −4} Ω-cm. We found that In doped CdO (ICO) transmits more solar photons than commercial fluorine doped tin oxide (FTO) with comparable sheet conductivity. The infrared transmittance is further extended to longer than 1500 nm wavelengths by depositing the In doped Cd{sub 1-x}Zn{sub x}O in ~ 1% of O{sub 2}. This material has a potential for applications as a transparent conductor for silicon and multi-junction solar cells. - Highlights: • Indium doped Cd1-xZnxO alloys across the full composition range were synthesized. • Alloys change from rocksalt (RS) to wurtzite (WZ) when x is higher than 30%. • RS-Cd1-xZnxO phase can be doped with In as efficiently as CdO, achieving a low resistivity ~ 2.0 × 10{sup −4} Ω-cm. • Wide transparency window from 380 to 1200 nm • In doped CdO transmits more solar photons than commercial fluorine doped tin oxide.

Quantum X waves with orbital angular momentum in nonlinear dispersive media

Science.gov (United States)

Ornigotti, Marco; Conti, Claudio; Szameit, Alexander

2018-06-01

We present a complete and consistent quantum theory of generalised X waves with orbital angular momentum in dispersive media. We show that the resulting quantised light pulses are affected by neither dispersion nor diffraction and are therefore resilient against external perturbations. The nonlinear interaction of quantised X waves in quadratic and Kerr nonlinear media is also presented and studied in detail.

Development of an X Window based operator's interface for a core monitoring system

International Nuclear Information System (INIS)

Vegh, J.; Huszar, J.; Laz, J.

1992-09-01

The components, functioning and programming concepts of the man-machine interface applied in an upgraded version of the core monitoring system and reactor information system VERONA for WWER-440 type nuclear power reactors, installed at the Paks Nuclear Power Plant, are described. The application of the X Window standard Graphical User Interface facilitated modular interface design and made program development easier and faster. (author) 3 refs.; 13 figs

Plasma focus as an x-ray source for tailoring of radiation in different energy windows

International Nuclear Information System (INIS)

Zakaullah, M.; Alamgir, K.; Shafiq, M.; Sharif, M.

2001-01-01

A low energy (2.3 kj) plasma focus energized by a single 32 micro f capacitor charged at 12 kv with filling gases hydrogen, neon and argon is investigated as an X-ray source. Experiments are conducted with a copper and an aluminum anode. Specifically, attention in given to tailoring the radiation in different windows, e. g. 1.2-1.3 keV, 1.3-1.5 keV, 2.5-5 keV and Cu-Ka line radiation. The highest X-ray emission is observed with neon filling and the copper anode in the 1.2-1.3 keV window, which speculated to be generated due to recombination of hydrogen like neon ions with a few eV to a few 10s of eV electrons. The wall-plug efficiency of the device is found to be 4%. The other significant emission occurs with Hydrogen filling, which exhibits wall plug efficiency of 1.7% for over all x-ray emission and 0.35% for Cu- Ka line radiation. The emission is dominated by the interaction of electrons in the current sheath with the anode tip. The emission with the aluminum anode and hydrogen filling is up to 10 j, which corresponds to wall-plug efficiency of 0.4%. The X-ray emission with argon filling is less significant. (author)

X-ray fluorescence camera for imaging of iodine media in vivo.

Science.gov (United States)

Matsukiyo, Hiroshi; Watanabe, Manabu; Sato, Eiichi; Osawa, Akihiro; Enomoto, Toshiyuki; Nagao, Jiro; Abderyim, Purkhet; Aizawa, Katsuo; Tanaka, Etsuro; Mori, Hidezo; Kawai, Toshiaki; Ehara, Shigeru; Sato, Shigehiro; Ogawa, Akira; Onagawa, Jun

2009-01-01

X-ray fluorescence (XRF) analysis is useful for measuring density distributions of contrast media in vivo. An XRF camera was developed for carrying out mapping for iodine-based contrast media used in medical angiography. Objects are exposed by an X-ray beam from a cerium target. Cerium K-series X-rays are absorbed effectively by iodine media in objects, and iodine fluorescence is produced from the objects. Next, iodine Kalpha fluorescence is selected out by use of a 58-microm-thick stannum filter and is detected by a cadmium telluride (CdTe) detector. The Kalpha rays are discriminated out by a multichannel analyzer, and the number of photons is counted by a counter card. The objects are moved and scanned by an x-y stage in conjunction with a two-stage controller, and X-ray images obtained by iodine mapping are shown on a personal computer monitor. The scan pitch of the x and y axes was 2.5 mm, and the photon counting time per mapping point was 2.0 s. We carried out iodine mapping of non-living animals (phantoms), and iodine Kalpha fluorescence was produced from weakly remaining iodine elements in a rabbit skin cancer.

Radiation transmission window, especially for X-ray image amplifier

International Nuclear Information System (INIS)

Christgau, H.; Bodes, U.

1979-01-01

The vacuum steel bulb of the image amplifier is closed by means of an Al window. Tightness of the joint between windowpane and window frame is obtained by a diffusion weld for which edge parts with Al coating, a pressure between 60 and 180 N/mm 2 and a temperature of 200 up to 500 0 C were provided. For weld improvemente the points of the Al windows to be connected may be nickle-plated before silvering them. (DG) [de

Thermal damage study of beryllium windows used as vacuum barriers in synchrotron radiation beamlines

International Nuclear Information System (INIS)

Holdener, F.R.; Johnson, G.L.; Karpenko, V.P.; Wiggins, R.K.; Cerino, J.A.; Dormiani, M.T.; Youngman, B.P.; Hoyt, E.W.

1987-01-01

An experimental study to investigate thermal-induced damage to SSRL-designed beryllium foil windows was performed at LLNL's Laser Welding Research Facility. The primary goal of this study was to determine the threshold at which thermal-stress-induced damage occurs in these commonly used vacuum barriers. An Nd:Yag pulsed laser with cylindrical optics and a carefully designed test cell provided a test environment that closely resembles the actual beamline conditions at SSRL. Tests performed on two beryllium window geometries, with different vertical aperture dimensions but equal foil thicknesses of 0.254 mm, resulted in two focused total-power thresholds at which incipient damage was determined. For a beam spot size similar to that of the Beamline-X Wiggler Line, onset of surface damage for a 5-mm by 25-mm aperture window was observed at 170 W after 174,000 laser pulses (1.2-ms pulse at 100 pps). A second window with double the vertical aperture dimension (10 mm by 25 mm) was observed to have surface cracking after 180,000 laser pulses with 85 W impinging its front surface. It failed after approximately 1,000,000 pulses. Another window of the same type (10 mm by 25 mm) received 2,160,000 laser pulses at 74.4 W, and subsequent metallographic sectioning revealed no signs of through-thickness damage. Comparison of windows with equal foil thicknesses and aperture dimensions has effectively identified the heat flux limit for incipient failure. The data show that halving the aperture's vertical dimension allows doubling the total incident power for equivalent onsets of thermal-induced damage

Electron Bernstein wave heating and emission measurement through the very narrow O-X-B mode conversion window in the LHD

Energy Technology Data Exchange (ETDEWEB)

Igami, H.; Shimozuma, T.; Yoshimura, Y.; Takahashi, H.; Nishiura, M.; Seki, T.; Osakabe, M.; Mutoh, T. [National Institute for Fusion Science, Toki (Japan); Kubo, S. [National Institute for Fusion Science, Toki, Japan and Department of Energy Engineering and Science, Nagoya Univ., Nagoya (Japan); Ogasawara, S.; Makino, R. [Department of Energy Engineering and Science, Nagoya Univ., Nagoya (Japan); Idei, H. [Research Institute for Applied Mechanics, Kyusyu Univ., Kasuga (Japan); Nagasaki, K. [Institute of Advanced Energy, Kyoto Univ., Uji (Japan)

2014-02-12

In the large helical device (LHD), the theoretically predicted width of the ordinary-extraordinary-electron Bernstein wave (O-X-B) mode conversion (MC) window is comparable to the beam width and the power deposition is located in the off-axis region if the 77GHz fundamental electron cyclotron (EC) wave of is launched from an existing horizontal port antenna. In the experiment, the actual MC window location was looked for with changing the aiming. The effective aiming with that the increase of the stored energy was observed was two degrees apart from the location of the theoretical MC window at a maximum. Measurement of the waves originated from the thermally emitted EBW and radiated via the B-X-O mode conversion process is effective to improve the accuracy of the theoretical prediction with comparison between the theoretical and the experimental results. The theoretical prediction suggests that the width of the MC window of the fundamental 77GHz EC wave can be expanded if the lower port antenna is used. On the other hand, the MC window of the second harmonic 154GHz EC wave is blocked by horizontal port wall if another horizontal port antenna is used. It is required to move the final mirror of the quasi-optical antenna toward the plasma surface. Focusing of the beam at the plasma cutoff is (PC) also necessary for the effective mode conversion.

Extrude Hone deburring with X-base media

Energy Technology Data Exchange (ETDEWEB)

Gillespie, L.K.

1973-09-01

Small precision mechanisms must have burr-free, sharp-edged parts to operate well. Controlling the size of burrs can lower burr removal costs and improve edge repeatability. Study results indicated that with conventional tooling approaches, Extrude Hone deburring with x-base media removes more material from the hole than desired and is less repeatable than required on precision miniature parts. With this media, the process is most applicable to precision miniature parts with burrs less than 25.4 ..mu..m thick, allowable hole size changes equal to burr thickness, and allowable hole size repeatability of +-0.2 times the actual average hole size change.

Radiation-transparent windows, method for imaging fluid transfers

Science.gov (United States)

Shu, Deming [Darien, IL; Wang, Jin [Burr Ridge, IL

2011-07-26

A thin, x-ray-transparent window system for environmental chambers involving pneumatic pressures above 40 bar is presented. The window allows for x-ray access to such phenomena as fuel sprays injected into a pressurized chamber that mimics realistic internal combustion engine cylinder operating conditions.

Teach yourself visually Windows 8.1

CERN Document Server

McFedries, Paul

2013-01-01

A practical guide for visual learners eager to get started with Windows 8.1 If you learn more quickly when you can see how things are done, this Visual guide is the easiest way to get up and running on Windows 8.1. It covers more than 150 essential Windows tasks, using full-color screen shots and step-by-step instructions to show you just what to do. Learn your way around the interface and how to install programs, set up user accounts, play music and other media files, download photos from your digital camera, go online, set up and secure an e-mail account, and much more.The tried-and-true f

Rigid thin windows for vacuum applications

Science.gov (United States)

Meyer, Glenn Allyn; Ciarlo, Dino R.; Myers, Booth Richard; Chen, Hao-Lin; Wakalopulos, George

1999-01-01

A thin window that stands off atmospheric pressure is fabricated using photolithographic and wet chemical etching techniques and comprises at least two layers: an etch stop layer and a protective barrier layer. The window structure also comprises a series of support ribs running the width of the window. The windows are typically made of boron-doped silicon and silicon nitride and are useful in instruments such as electron beam guns and x-ray detectors. In an electron beam gun, the window does not impede the electrons and has demonstrated outstanding gun performance and survivability during the gun tube manufacturing process.

Dental Videographic Analysis using Digital Age Media.

Science.gov (United States)

Agarwal, Anirudh; Seth, Karan; Parmar, Siddharaj; Jhawar, Rahul

2016-01-01

This study was to evaluate a new method of smile analysis using videographic and photographic softwares (as in this study Photoshop Elements X, Windows Movie Maker 2012) as primary assessment tools and to develop an index for malocclusion and treatment plan that could be used in assessing severity of maloc-clussion. Agarwal A, Seth K, Parmar S, Jhawar R. Dental Videographic Analysis using Digital Age Media. Int J Clin Pediatr Dent 2016;9(4):355-363.

Optimum design of beam window's diameter and thickness of Hyper target system

International Nuclear Information System (INIS)

Cho, C. H.; Tak, N. I.; Song, T. Y.; Park, W. S.

2002-01-01

HYPER is designed to transmute long-lived TRU and fission products such as Tc-99 and I-129. Pb-Bi is used as the coolant and spallation target material at the same time. HYPER is expected to need about 20mA proton beam to sustain a 1000MW th power level. The cylindrical beam tube and spherical window is adopted as the basic window shape of HYPER. The window diameter and the window thickness are varied to find the maximum allowable current based on the design criteria : Pb-Bi temperature < 500 .deg. C, window temperature < 600 .deg. C, Pb-Bi velocity < 2m/s and window stress < 160MPa. The LAHET code is used to simulate heat generation. CFX is also used for the thermal-hydraulics calculation. Based on our design criteria, the maximum allowable current is calculated to be about 9.2mA, which is smaller than the required current. Therefore, an upgrade of the target system design is required

An open software system based on X Windows for process control and equipment monitoring

International Nuclear Information System (INIS)

Aimar, A.; Carlier, E.; Mertens, V.

1992-01-01

The construction and application of a configurable open software system for process control and equipment monitoring can speed up and simplify the development and maintenance of equipment specific software as compared to individual solutions. The present paper reports the status of such an approach for the distributed control systems of SPS and LEP beam transfer components, based on X Windows and the OSF/Motif tool kit and applying data modeling and software engineering methods. (author)

Evolution of cluster X-ray luminosities and radii: Results from the 160 square degree rosat survey

DEFF Research Database (Denmark)

Vikhlinin, A.; McNamara, B.R.; Forman, W.

1998-01-01

We searched for cluster X-ray luminosity and radius evolution using our sample of 203 galaxy clusters detected in the 160 deg(2) survey with the ROSAT PSPC (Vikhlinin et al.). With such a large area survey, it is possible, for the first time with ROSAT, to test the evolution of luminous clusters, L......-X > 3 x 10(44) ergs s(-1) in the 0.5-2 keV band. We detect a factor of 3-4 deficit of such luminous clusters at z > 0.3 compared with the present. The evolution is much weaker or absent at modestly lower luminosities, (1-3) x 10(44) ergs s(-1). At still lower luminosities, we find no evolution from...... the analysis of the log N-log S relation. The results in the two upper L, bins are in agreement with the Einstein Extended Medium-Sensitivity Survey evolution result (Gioia et al.; Henry ct al.), which was obtained using a completely independent cluster sample. The low-L-X results are in agreement with other...

An analytical X-ray CdTe detector response matrix for incomplete charge collection correction for photon energies up to 300 keV

Science.gov (United States)

Kurková, Dana; Judas, Libor

2018-05-01

Gamma and X-ray energy spectra measured with semiconductor detectors suffer from various distortions, one of them being so-called "tailing" caused by an incomplete charge collection. Using the Hecht equation, a response matrix of size 321 × 321 was constructed which was used to correct the effect of incomplete charge collection. The correction matrix was constructed analytically for an arbitrary energy bin and the size of the energy bin thus defines the width of the spectral window. The correction matrix can be applied separately from other possible spectral corrections or it can be incorporated into an already existing response matrix of the detector. The correction was tested and its adjustable parameters were optimized on the line spectra of 57Co measured with a cadmium telluride (CdTe) detector in a spectral range from 0 up to 160 keV. The best results were obtained when the values of the free path of holes were spread over a range from 0.4 to 1.0 cm and weighted by a Gauss function. The model with the optimized parameter values was then used to correct the line spectra of 152Eu in a spectral range from 0 up to 530 keV. An improvement in the energy resolution at full width at half maximum from 2.40 % ± 0.28 % to 0.96 % ± 0.28 % was achieved at 344.27 keV. Spectra of "narrow spectrum series" beams, N120, N150, N200, N250 and N300, generated with tube voltages of 120 kV, 150 kV, 200 kV, 250 kV and 300 kV respectively, and measured with the CdTe detector, were corrected in the spectral range from 0 to 160 keV (N120 and N150) and from 0 to 530 keV (N200, N250, N300). All the measured spectra correspond both qualitatively and quantitatively to the available reference data after the correction. To obtain better correspondence between N150, N200, N250 and N300 spectra and the reference data, lower values of the free paths of holes (range from 0.16 to 0.65 cm) were used for X-ray spectra correction, which suggests energy dependence of the phenomenon.

DNA strand breaks induced by soft X-ray pulses from a compact laser plasma source

Czech Academy of Sciences Publication Activity Database

Adjei, D.; Wiechec, A.; Wachulak, P.; Ayele, M. G.; Lekki, J.; Kwiatek, W. M.; Bartnik, A.; Davídková, Marie; Vyšín, Luděk; Juha, Libor; Pina, L.; Fiedorowicz, H.

2016-01-01

Roč. 120, MAR (2016), s. 17-25 ISSN 0969-806X R&D Projects: GA ČR GA13-28721S; GA ČR(CZ) GBP108/12/G108 EU Projects: European Commission(XE) 284464 - LASERLAB-EUROPE Institutional support: RVO:68378271 ; RVO:61389005 Keywords : laser-produced plasma * soft X-rays * radiobiology * gas puff target * water window * DNA strand break Subject RIV: BO - Biophysics Impact factor: 1.315, year: 2016

Ultra-high resolution water window x ray microscope optics design and analysis

Science.gov (United States)

Shealy, David L.; Wang, C.

1993-01-01

This project has been focused on the design and analysis of an ultra-high resolution water window soft-x-ray microscope. These activities have been accomplished by completing two tasks contained in the statement of work of this contract. The new results from this work confirm: (1) that in order to achieve resolutions greater than three times the wavelength of the incident radiation, it will be necessary to use spherical mirror surfaces and to use graded multilayer coatings on the secondary in order to accommodate the large variations of the angle of incidence over the secondary when operating the microscope at numerical apertures of 0.35 or greater; (2) that surface contour errors will have a significant effect on the optical performance of the microscope and must be controlled to a peak-to-valley variation of 50-100 A and a frequency of 8 periods over the surface of a mirror; and (3) that tolerance analysis of the spherical Schwarzschild microscope has been shown that the water window operations will require 2-3 times tighter tolerances to achieve a similar performance of operations with 130 A radiation. These results have been included in a manuscript included in the appendix.

Contrast Media for X-ray and Magnetic Resonance Imaging: Development, Current Status and Future Perspectives.

Science.gov (United States)

Frenzel, Thomas; Lawaczeck, Rüdiger; Taupitz, Matthias; Jost, Gregor; Lohrke, Jessica; Sieber, Martin A; Pietsch, Hubertus

2015-09-01

Over the last 120 years, the extensive advances in medical imaging allowed enhanced diagnosis and therapy of many diseases and thereby improved the quality of life of many patient generations. From the beginning, all technical solutions and imaging procedures were combined with dedicated pharmaceutical developments of contrast media, to further enhance the visualization of morphology and physiology. This symbiosis of imaging hardware and contrast media development was of high importance for the development of modern clinical radiology. Today, all available clinically approved contrast media fulfill the highest requirements for clinical safety and efficacy. All new concepts to increase the efficacy of contrast media have also to consider the high clinical safety standards and cost of goods of current marketed contrast media. Nevertheless, diagnostic imaging will contribute significantly to the progresses in medicine, and new contrast media developments are mandatory to address the medical needs of the future.

Design of Rose Bengal/FTO optical thin film system as a novel nonlinear media for infrared blocking windows

Directory of Open Access Journals (Sweden)

S.M. El-Bashir

Full Text Available Rose Bengal (RB is a new organic semiconductor with the highly stable layer, was deposited on highly cleaned conductive glass substrate known as (FTO glass with different thickness in the range from 80 to 292 nm. XRD showed an entirely amorphous structure of the studied film thicknesses. The observed peaks are the indexed peaks for FTO layer. Spectrophotometric data as transmittance, reflectance, and absorbance were used for the analysis the optical constant of RB/FTO optical thin film system. Refractive index was calculated using Fresnel’s equation with the aid of reflectance and absorption index. The dielectric constant, dielectric loss and dissipation factor were discussed and analyzed according to the applied optical theories. Nonlinear parameters such as third order nonlinear optical susceptibility and the nonlinear refractive index were calculated based on the linear refractive index of the applications of this material in nonlinear media. The results showed that Rose Bengal is a proving material for wide scale optoelectronic applications such as infrared blocking windows. Keywords: Rose Bengal, Dielectric parameters, Linear/nonlinear optics, Dye/FTO, IR blocking windows

What's new in Windows 8.1 for dummies

CERN Document Server

Underdahl, Brian

2013-01-01

What's New in Windows 8.1 For Dummies Pocket Edition provides a brief, inexpensive, and focused guide for Windows 8 users upgrading to 8.1. Chapters include:It's all about you: An exploration of the customization features, from flexible sizing on icons to shared wallpaper to boot options.We can build it better: Review of the updates to applications with special emphaisis on communications and media appsShiny new toys: Walkthroughs of the new features added to Windows 8.1, including the start button and search functionTen reasons you were smart to upgrade: In the spirit of the For Dummies Part

Thermal and structural behavior of filters and windows for synchrotron x-ray sources

International Nuclear Information System (INIS)

Wang, Z.; Hahn, U.; Dejus, R.; Kuzay, T.

1993-01-01

This report contains the following discussions: Introduction: Use of filters and windows in the front end designs; An interactive code for 3D graphic viewing of absorbed power in filters/windows and a new heat load generation algorithm for the finite element analysis; Failure criteria and analysis methods for the filter and window assembly; Comparison with test data and existing devices in HASYLAB; Cooling the filter: Radiation cooling or conduction cooling?; Consideration of window and filter thickness: Thicker or thinner?; Material selection criteria for filters/windows; Photon transmission through filters/windows; Window and filter design for APS undulators; Window and filter design for APS wigglers; and Window design for APS bending magnet front ends

Prolonged retainment of contrast media in renal tumours by oily X-ray contrast media

International Nuclear Information System (INIS)

Ryzkov, V.K.; Anisimov, V.N.

1990-01-01

In 194 patients with renal tumours an angiographic investigation with the oily X-ray contrast medium Iodolipol was carried out. A selective tropism of oily X-ray contrast media was found in the malignant zones only. The application of the preparation caused no complications. The oily X-ray contrast medium persisted in the tumours over several weeks or months. After embolization of the renal arteria a moderate size reduction of malign tumours in the first 10-14 d was seen. The ability of Iodolipol for a lasting retainment in malign tumour tissue allows a follow-up of the involution of the pathologic focus after arterial embolization of the tumour vessels. (author)

Development of multi-channel high power rectangular RF window for LHCD system employing high temperature vacuum brazing technique

International Nuclear Information System (INIS)

Sharma, P K; Ambulkar, K K; Parmar, P R; Virani, C G; Thakur, A L; Joshi, L M; Nangru, S C

2010-01-01

A 3.7 GHz., 120 kW (pulsed), lower hybrid current drive (LHCD) system is employed to drive non-inductive plasma current in ADITYA tokamak. The rf power is coupled to the plasma through grill antenna and is placed in vacuum environment. A vacuum break between the pressurized transmission line and the grill antenna is achieved with the help of a multi (eight) channel rectangular RF vacuum window. The phasing between adjacent channels of 8-channel window (arranged in two rows) is important for launching lower hybrid waves and each channel should have independent vacuum window so that phase information is retained. The geometrical parameter of the grill antenna, like periodicity (9mm), channel dimensions (cross sectional dimension of 76mm x 7mm), etc. is to be maintained. These design constraint demanded a development of a multi channel rectangular RF vacuum window. To handle rf losses and thermal effects, high temperature vacuum brazing techniques is desired. Based on the above requirements we have successfully developed a multi channel rectangular rf vacuum window employing high temperature vacuum brazing technique. During the development process we could optimize the chemical processing parameters, brazing process parameters, jigs and fixtures for high temperature brazing and leak testing, etc. Finally the window is tested for low power rf performance using VNA. In this paper we would present the development of the said window in detail along with its mechanical, vacuum and rf performances.

Development of multi-channel high power rectangular RF window for LHCD system employing high temperature vacuum brazing technique

Energy Technology Data Exchange (ETDEWEB)

Sharma, P K; Ambulkar, K K; Parmar, P R; Virani, C G; Thakur, A L [Institute for Plasma Research, Bhat, Gandhinagar 382428 (India); Joshi, L M; Nangru, S C, E-mail: pramod@ipr.res.i [Central Electronics Engineering Research Institute, Pilani, Rajasthan 333 031 (India)

2010-02-01

A 3.7 GHz., 120 kW (pulsed), lower hybrid current drive (LHCD) system is employed to drive non-inductive plasma current in ADITYA tokamak. The rf power is coupled to the plasma through grill antenna and is placed in vacuum environment. A vacuum break between the pressurized transmission line and the grill antenna is achieved with the help of a multi (eight) channel rectangular RF vacuum window. The phasing between adjacent channels of 8-channel window (arranged in two rows) is important for launching lower hybrid waves and each channel should have independent vacuum window so that phase information is retained. The geometrical parameter of the grill antenna, like periodicity (9mm), channel dimensions (cross sectional dimension of 76mm x 7mm), etc. is to be maintained. These design constraint demanded a development of a multi channel rectangular RF vacuum window. To handle rf losses and thermal effects, high temperature vacuum brazing techniques is desired. Based on the above requirements we have successfully developed a multi channel rectangular rf vacuum window employing high temperature vacuum brazing technique. During the development process we could optimize the chemical processing parameters, brazing process parameters, jigs and fixtures for high temperature brazing and leak testing, etc. Finally the window is tested for low power rf performance using VNA. In this paper we would present the development of the said window in detail along with its mechanical, vacuum and rf performances.

Limited tender notification for the AMC of desktop computers and

Indian Academy of Sciences (India)

Brand. 1 INTEL 82945 EXPRESS. P4 3.0GHZ. 1X2GB + 1 x 1 GB =3GB. DDR2. 160 GB STATA. WINDOWS 7 PRO SP1. 32BIT. CD/ DVDRW. 17 " LCD. 2 INTEL G31PR. PENTIUM DUAL E2160. 1.8GHZ. 2X2GB =4GB DDR2. 160 GB STATA. WINDOWS 7 PRO SP1. 32BIT. CD/ DVDRW. 17 " LCD. 3 INTEL G31/33 EXPRESS.

Design of the nickel-like tin x-ray laser at 12.0 nm

International Nuclear Information System (INIS)

Yan Fei; Zhang Jie; Lu Xin; Zhong, Jia Y.

2005-01-01

The effects of the drive laser intensity, pulse duration, and pulse configuration on the performance of the Ni-like Sn x-ray laser at 12.0 nm (4d→4p, J=0→1) are investigated with use of a one-dimensional hydrodynamic code coupled with an atomic physics code. High gain operation is predicted for the optimized drive pulse configuration. The effects of refraction and saturation on the propagation of the x-ray laser in the plasma medium are also investigated by use of a two-dimensional ray-tracing code. The results show that the refraction plays an important role. The saturated output with an effective gain product length of 17.88 can be obtained for an ∼0.40-cm-long plasma column by use of optimized parameters

PENGEMBANGAN MEDIA PEMBELAJARAN MENGGUNAKAN POWERPOINT DISERTAI VISUAL BASIC FOR APPLICATION MATERI JARAK PADA BANGUN RUANG KELAS X

Directory of Open Access Journals (Sweden)

Siti Marfuah

2016-10-01

Full Text Available Penelitian ini bertujuan : (1 menghasilkan media pembelajaran menggunakan powerpoint disertai visual basic for application materi jarak pada bangun ruang yang valid dan praktis di kelas X, dan (2 mengetahui efek potensial dari pengembangan media pembelajaran menggunakan powerpoint disertai visual basic for application materi jarak pada bangun ruang di kelas X. Jenis penelitian yang digunakan adalah Design Research tipe Development Study. Subjek penelitian ini adalah siswa kelas X SMA Negeri 4 Palembang tahun ajaran 2014/2015. Teknik pengumpulan data adalah dengan walkthrough,, tes, angket, dan wawancara. Hasil dari penelitian ini adalah: (1 Penelitian ini telah menghasilkan media pembelajaran menggunakan powerpoint disertai visual basic for application materi jarak pada bangun ruang yang valid dan praktis. (2 media pembelajaran  yang dikembangkan memiliki efek potensial terhadap hasil belajar dan sikap positif siswa. Kata Kunci : Pengembangan, Media Pembelajaran, Powerpoint, Jarak pada Bangun Ruang This design research typed Development Study aims to: (1 develop valid and practical learning media using power point and visual basic for application for Distance in three-dimensional objects topic in class X, and (2 to determine the potential effects media developed by using power point and visual basic for application for Distance in three-dimensional objects topic in class X. The subjects were students of class X SMA Negeri 4 Palembang academic year 2014/2015. Data were collected through walkthrough, tests, questionnaires, and interviews. The study results show that (1 This research has produced valid and practical learning media using power point and visual basic for application for Distance in three-dimensional objects topic; (2 the learning media developed has potential effects on students learning outcomes and students positive attitude. Keywords: development, learning media, powerpoint, distance in three-dimensional object

Imaging biofilm in porous media using X-ray computed microtomography.

Science.gov (United States)

Davit, Y; Iltis, G; Debenest, G; Veran-Tissoires, S; Wildenschild, D; Gerino, M; Quintard, M

2011-04-01

In this study, a new technique for three-dimensional imaging of biofilm within porous media using X-ray computed microtomography is presented. Due to the similarity in X-ray absorption coefficients for the porous media (plastic), biofilm and aqueous phase, an X-ray contrast agent is required to image biofilm within the experimental matrix using X-ray computed tomography. The presented technique utilizes a medical suspension of barium sulphate to differentiate between the aqueous phase and the biofilm. Potassium iodide is added to the suspension to aid in delineation between the biofilm and the experimental porous medium. The iodide readily diffuses into the biofilm while the barium sulphate suspension remains in the aqueous phase. This allows for effective differentiation of the three phases within the experimental systems utilized in this study. The behaviour of the two contrast agents, in particular of the barium sulphate, is addressed by comparing two-dimensional images of biofilm within a pore network obtained by (1) optical visualization and (2) X-ray absorption radiography. We show that the contrast mixture provides contrast between the biofilm, the aqueous-phase and the solid-phase (beads). The imaging method is then applied to two three-dimensional packed-bead columns within which biofilm was grown. Examples of reconstructed images are provided to illustrate the effectiveness of the method. Limitations and applications of the technique are discussed. A key benefit, associated with the presented method, is that it captures a substantial amount of information regarding the topology of the pore-scale transport processes. For example, the quantification of changes in porous media effective parameters, such as dispersion or permeability, induced by biofilm growth, is possible using specific upscaling techniques and numerical analysis. We emphasize that the results presented here serve as a first test of this novel approach; issues with accurate segmentation of

Understanding Windows | Efficient Windows Collaborative

Science.gov (United States)

Foundry Foundry New Construction Windows Window Selection Tool Selection Process Design Guidance Installation Replacement Windows Window Selection Tool Assessing Options Selection Process Design Guidance Installation Understanding Windows Benefits Design Considerations Measuring Performance Performance Standards

The soft-X-ray emission of Ark 120. XMM-Newton, NuSTAR, and the importance of taking the broad view

DEFF Research Database (Denmark)

Matt, G.; Marinucci, A.; Guainazzi, M.

2014-01-01

We present simultaneous XMM-Newton and NuSTAR observations of the 'bare' Seyfert 1 galaxy, Ark 120, a system in which ionized absorption is absent. The NuSTAR hard-X-ray spectral coverage allows us to constrain different models for the excess soft-X-ray emission. Among phenomenological models, a ...

News and social media: windows into community perspectives on disinvestment.

Science.gov (United States)

Street, Jackie M; Hennessy, Sophie E; Watt, Amber M; Hiller, Janet E; Elshaug, Adam G

2011-10-01

The aim of this study, in the context of disinvestment related health technology assessment, is to examine whether analysis of Web 2.0--commercial media output, blogs, and discussion forums--can provide an understanding of media framing, community perspectives, and the sociopolitical aspects of an entrenched technology. Thematic analysis of relevant data from fifty-nine media articles, thirty-nine discussion forums, thirteen blogs, and three Facebook pages relating to our case study: public funding for assisted reproductive technology services. Mainstream media and community-based social media responses were compared. Media responses were narrow, primarily describing emotive individual narratives or the political nexus of interests. Community (including patient) responses were broader including discussion of opportunity cost and vested interests but mostly reflected the polar ends of the debate, diverging strongly for or against disinvestment from public funding. Web2.0 and media analysis offers an inexpensive method to capture media portrayal, divergent community responses both to that portrayal and independent of it, and insight into the sociopolitical aspects of an entrenched technology undergoing disinvestment debate.

Simultaneous collection method of on-peak window image and off-peak window image in Tl-201 imaging

International Nuclear Information System (INIS)

Murakami, Tomonori; Noguchi, Yasushi; Kojima, Akihiro; Takagi, Akihiro; Matsumoto, Masanori

2007-01-01

Tl-201 imaging detects the photopeak (71 keV, in on-peak window) of characteristic X-rays of Hg-201 formed from Tl-201 decay. The peak is derived from 4 rays of different energy and emission intensity and does not follow in Gaussian distribution. In the present study, authors made an idea for the method in the title to attain the more effective single imaging, which was examined for its accuracy and reliability with phantoms and applied clinically to Tl-201 scintigraphy in a patient. The authors applied the triple energy window method for data acquisition: the energy window setting was made on Hg-201 X-rays photopeak in three of the lower (3%, L), main (72 keV, M) and upper (14%, U) windows with the gamma camera with 2-gated detector (Toshiba E. CAM/ICON). L, M and U images obtained simultaneously were then constructed to images of on-peak (L+M, Mock on-peak) and off-peak (M+U) window settings for evaluation. Phantoms for line source with Tl-201-containing swab and for multi-defect with acrylic plate containing Tl-201 solution were imaged in water. The female patient with thyroid cancer was subjected to preoperative scintigraphy under the defined conditions. Mock on-, off-peak images were found to be equivalent to the true (ordinary, clinical) on-, off-peak ones, and the present method was thought usable for evaluation of usefulness of off-peak window data. (R.T.)

Degradation of organophosphorus compounds by X-ray irradiation

International Nuclear Information System (INIS)

Trebse, P.; Arcon, I.

2002-01-01

Complete text of publication follows. Our research presented in this contribution aims to elucidate the degradation mechanisms of organophosphate pesticides as organic pollutants by X-ray irradiation. Diazinon, one of the most widely used pesticides in Slovenia, has been chosen as a model compound for the study of radiation induced degradation of organophosphorus pesticides. Recent studies have shown that the degradation of the pesticide at normal conditions (room temperature, exposure to daylight) is strongly enhanced when the pesticide is exposed to UV light (Hg lamp, λ=254 nm, XeCl excimer laser, λ=308 nm). In our study we irradiated the pesticide in aqueous media with a white x-ray beam from a conventional x-ray source. Mo X-ray tube operating at the high voltage of 55 kV and a current of 45 mA was used. The flux of the continuous X-ray beam was stabilized within 1%. Saturated water solution of the pesticide (volume: 4mL, conc. of 40 mg L -1 ) was inserted in 1 cm long lucite cell with 1 mm thick lucite windows. The whole volume of the solution in the cell was exposed to the unfiltered X-ray beam. The dose rate on the sample was about 1 mGy/s. Different irradiation times between 30 min to 120 min were chosen to study the dependence of the pesticide decomposition with the absorbed dose. Solid phase extraction was employed for sample extraction from the solution, and gas chromatography was used for the identification and quantification of the compounds. The results show that the concentration of the pesticide in the solution decreases exponentially with the exposure time, i.e. with the absorbed dose. At irradiation conditions described above, the time constant of the exponential decrease was 74 min

Dynamics of a Z Pinch X Ray Source for Heating ICF Relevant Hohlraums to 120-160eV

Energy Technology Data Exchange (ETDEWEB)

SANFORD,THOMAS W. L.; OLSON,RICHARD E.; MOCK,RAYMOND CECIL; CHANDLER,GORDON A.; LEEPER,RAMON J.; NASH,THOMAS J.; RUGGLES,LAURENCE E.; SIMPSON,WALTER W.; STRUVE,KENNETH W.; PETERSON,D.L.; BOWERS,R.L.; MATUSKA,W.

2000-07-10

A z-pinch radiation source has been developed that generates 60 {+-} 20 KJ of x-rays with a peak power of 13 {+-} 4 TW through a 4-mm diameter axial aperture on the Z facility. The source has heated NIF (National Ignition Facility)-scale (6-mm diameter by 7-mm high) hohlraums to 122 {+-} 6 eV and reduced-scale (4-mm diameter by 4-mm high) hohlraums to 155 {+-} 8 eV -- providing environments suitable for indirect-drive ICF (Inertial Confinement Fusion) studies. Eulerian-RMHC (radiation-hydrodynamics code) simulations that take into account the development of the Rayleigh-Taylor instability in the r-z plane provide integrated calculations of the implosion, x-ray generation, and hohlraum heating, as well as estimates of wall motion and plasma fill within the hohlraums. Lagrangian-RMHC simulations suggest that the addition of a 6 mg/cm{sup 3} CH{sub 2} fill in the reduced-scale hohlraum decreases hohlraum inner-wall velocity by {approximately}40% with only a 3--5% decrease in peak temperature, in agreement with measurements.

Dynamics of a Z Pinch X Ray Source for Heating ICF Relevant Hohlraums to 120-160eV

International Nuclear Information System (INIS)

Sanford, Thomas W.L.; Olson, Richard E.; Mock, Raymond Cecil; Chandler, Gordon A.; Leeper, Ramon J.; Nash, Thomas J.; Ruggles, Laurence E.; Simpson, Walter W.; Struve, Kenneth W.; Peterson, D.L.; Bowers, R.L.; Matuska, W.

2000-01-01

A z-pinch radiation source has been developed that generates 60 ± 20 KJ of x-rays with a peak power of 13 ± 4 TW through a 4-mm diameter axial aperture on the Z facility. The source has heated NIF (National Ignition Facility)-scale (6-mm diameter by 7-mm high) hohlraums to 122 ± 6 eV and reduced-scale (4-mm diameter by 4-mm high) hohlraums to 155 ± 8 eV -- providing environments suitable for indirect-drive ICF (Inertial Confinement Fusion) studies. Eulerian-RMHC (radiation-hydrodynamics code) simulations that take into account the development of the Rayleigh-Taylor instability in the r-z plane provide integrated calculations of the implosion, x-ray generation, and hohlraum heating, as well as estimates of wall motion and plasma fill within the hohlraums. Lagrangian-RMHC simulations suggest that the addition of a 6 mg/cm 3 CH 2 fill in the reduced-scale hohlraum decreases hohlraum inner-wall velocity by ∼40% with only a 3--5% decrease in peak temperature, in agreement with measurements

Development of actively cooled windows for plasma observation during quasi-continuous operation of the W7-X stellarator

International Nuclear Information System (INIS)

Konig, R.; Grosser, K.; Hildebrandt, D.; Pasch, E.; Werner, T.; Klinger, T.; Ogorodnikova, O.

2005-01-01

With the stellarator W7-X a step to quasi-continuous plasma operation will be made. The cooling system of the machine is designed such that two 30 min discharges can be run per day. Right from the start of operation 10 MW of ECRH heating power will be available for quasi-continuous operation. A working group 'Plasma Facing Optical Components' has been formed which presently concentrates on the development of water cooled windows for UV/VR/IR periscopes which can withstand the expected maximum heat loads of up to 50 kW/m 2 which due to the predominantly short wavelength nature of the radiation emitted by the plasma will be absorbed within the first millimeter of any window. We will report on the detailed Finite Element (ANSYS R ) calculations of the heat and stress distribution across the windows. Calculations have been undertaken for a large number of different window materials which are required for the various spectral regions covered by the miscellaneous diagnostics, so that the most suitable material for each application can easily be identified. Also the dependence of the cooling rate on the window diameter and thickness has been studied. The calculations show that at a power load of 50 kW/m 2 cooled sapphire windows can be used for window sizes up to ∼200 mm diameter but that for many of the other materials like ZnSe, ZnS, CaF 2 , MgF 2 and quartz window sizes need to be limited to considerably smaller sizes. Detailed simulations of the local radiation power load distribution demonstrate that by careful design the load on individual optical components can be considerably reduced. A vacuum test chamber, equipped with a vacuum compatible IR heater has been build. In this chamber a low cost, easily exchangeable window design using Helicoflex gaskets on either side of a 60 mm exposed diameter quartz window have been successfully tested over 70 heat cycles up to a maximum temperature of 450 o C at power loads of 15 kW/m 2 . The design proved to be water and

Efficiency enhancement using a Zn1- x Ge x -O thin film as an n-type window layer in Cu2O-based heterojunction solar cells

Science.gov (United States)

Minami, Tadatsugu; Nishi, Yuki; Miyata, Toshihiro

2016-05-01

Efficiency enhancement was achieved in Cu2O-based heterojunction solar cells fabricated with a zinc-germanium-oxide (Zn1- x Ge x -O) thin film as the n-type window layer and a p-type Na-doped Cu2O (Cu2O:Na) sheet prepared by thermally oxidizing Cu sheets. The Ge content (x) dependence of the obtained photovoltaic properties of the heterojunction solar cells is mainly explained by the conduction band discontinuity that results from the electron affinity difference between Zn1- x Ge x -O and Cu2O:Na. The optimal value of x in Zn1- x Ge x -O thin films prepared by pulsed laser deposition was observed to be 0.62. An efficiency of 8.1% was obtained in a MgF2/Al-doped ZnO/Zn0.38Ge0.62-O/Cu2O:Na heterojunction solar cell.

High performance sapphire windows

Science.gov (United States)

Bates, Stephen C.; Liou, Larry

1993-02-01

High-quality, wide-aperture optical access is usually required for the advanced laser diagnostics that can now make a wide variety of non-intrusive measurements of combustion processes. Specially processed and mounted sapphire windows are proposed to provide this optical access to extreme environment. Through surface treatments and proper thermal stress design, single crystal sapphire can be a mechanically equivalent replacement for high strength steel. A prototype sapphire window and mounting system have been developed in a successful NASA SBIR Phase 1 project. A large and reliable increase in sapphire design strength (as much as 10x) has been achieved, and the initial specifications necessary for these gains have been defined. Failure testing of small windows has conclusively demonstrated the increased sapphire strength, indicating that a nearly flawless surface polish is the primary cause of strengthening, while an unusual mounting arrangement also significantly contributes to a larger effective strength. Phase 2 work will complete specification and demonstration of these windows, and will fabricate a set for use at NASA. The enhanced capabilities of these high performance sapphire windows will lead to many diagnostic capabilities not previously possible, as well as new applications for sapphire.

A deep X-ray view of the bare AGN Ark120. IV. XMM-Newton and NuSTAR spectra dominated by two temperature (warm, hot) Comptonization processes

DEFF Research Database (Denmark)

Porquet, D.; Reeves, J. N.; Matt, G.

2018-01-01

an extensive campaign observing Ark 120 in X-rays with XMM-Newton (4 × 120 ks, 2014 March 18–24), and NuSTAR (65.5 ks, 2014 March 22).Results. During this very deep X-ray campaign, the source was caught in a high-flux state similar to the earlier 2003 XMM-Newton observation, and about twice as bright...

The significance of the allergy history in the use of intravenous X-ray contrast media

International Nuclear Information System (INIS)

Schmidt, M.; Kroczek, U.

1986-01-01

A restrospective study correlating allergy histories and reactions to X-ray contrast media was performed with a study group containing 519 patients receiving intravenous and infusion cholangiograms and 827 patients receiving intravenous and infusion pyelograms. Reactions against X-ray contrast media were observed significantly more frequently among patients with a positive allergy history independent of the suspected allergy (p [de

Survey of the pharmacology of non-ionic X-ray contrast media

International Nuclear Information System (INIS)

Turnheim, K.

1986-01-01

The non-ionic X-ray contrast media metrizamide, iopamidol, iohexol, and iopromide do not bind calcium and are less hyperosmolar than the conventional ionic contrast media, for instance amidotrizoate (diatrizoate), iothalamte, or ioglicate. Hence the use of non-ionic contrast media is associated with less undesirable side-effects that are attributable to hypertonicity such as an increase in circulating plasma volume, decreased deformability of red blood cells, damage of vascular endothelium with consequent activation of blood coagulation, the complement system and fibrinolysis, increased release of bradykinin and histamine, cardiac arrhythimas, diuresis, vasodilation and decreased blood pressure, pain and heat sensation. Because of less dilution the quality of imaging is also better. According to the intravenous LD 50 in experimental animals the acute toxicity of non-ionic contrast media is lower than that of ionic media. With respect to contrast quality and the rate of side-effects tha various non-ionic contrast media appear to be equivalent. Despite their higher price and higher viscosity it is probable that the non-ionic contrast media will replace the classical ionic media, especially in angio- and myelography. (Author)

The X-625 Groundwater Treatment Facility: A field-scale test of trichloroethylene dechlorination using iron filings for the X-120/X-749 groundwater plume

International Nuclear Information System (INIS)

Liang, L.; West, O.R.; Korte, N.E.

1997-09-01

The dehalogenation of chlorinated solvents by zero-valence iron has recently become the subject of intensive research and development as a potentially cost-effective, passive treatment for contaminated groundwater through reactive barriers. Because of its successful application in the laboratory and other field sites, the X-625 Groundwater Treatment Facility (GTF) was constructed to evaluate reactive barrier technology for remediating trichloroethylene (TCE)-contaminated groundwater at the Portsmouth Gaseous Diffusion Plant (PORTS). The X-625 GTF was built to fulfill the following technical objectives: (1) to test reactive barrier materials (e.g., iron filings) under realistic groundwater conditions for long term applications, (2) to obtain rates at which TCE degrades and to determine by-products for the reactive barrier materials tested, and (3) to clean up the TCE-contaminated water in the X-120 plume. The X-625 is providing important field-scale and long-term for the evaluation and design of reactive barriers at PORTS. The X-625 GTS is a unique facility not only because it is where site remediation is being performed, but it is also where research scientists and process engineers can test other promising reactive barrier materials. In addition, the data collected from X-625 GTF can be used to evaluate the technical and economic feasibility of replacing the activated carbon units in the pump-and-treat facilities at PORTS

Spectroscopic investigations of hard x-ray emission from 120 ps laser-produced plasmas at intensities near 1017 W cm-2

International Nuclear Information System (INIS)

Dunn, J.; Young, B.K.F.; Osterheld, A.L.; Foord, M.E.; Walling, R.S.; Stewart, R.E.; Faenov, A.Y.

1995-11-01

Spectroscopic investigations of the x-ray emission of plasmas heated by 120 ps, frequency doubled pulses from the JANUS Nd: glass laser are presented. High Z K-shell spectra emitted from slab targets heated to near 10 17 W cm -2 intensity are investigated. High resolution (γ/Δγ>5000) x-ray spectra of multicharged ions of H-like Ti, Co, Ni, Cu, and also H-like Sc in the spectral range 1.5--3.0 angstrom are obtained in single laser shots using a spherically bent Mica crystal spectrograph with a 186 mm radius of curvature. The spectra- have one dimensional spatial resolution of about 25μm and indicate that the size of the emission zone of the resonance, transitions is 2 keV and density∼10 22 cm -3 . These experiments demonstrate that with modest laser energy, plasmas heated by high-intensity 120 ps lasers provide a very bright source of hard ∼8 keV x-ray emission

Window Glazing Types | Efficient Windows Collaborative

Science.gov (United States)

Foundry Foundry New Construction Windows Window Selection Tool Selection Process Design Guidance Installation Replacement Windows Window Selection Tool Assessing Options Selection Process Design Guidance Installation Understanding Windows Benefits Design Considerations Measuring Performance Performance Standards

Window Frame Types | Efficient Windows Collaborative

Science.gov (United States)

Foundry Foundry New Construction Windows Window Selection Tool Selection Process Design Guidance Installation Replacement Windows Window Selection Tool Assessing Options Selection Process Design Guidance Installation Understanding Windows Benefits Design Considerations Measuring Performance Performance Standards

Window Operator Types | Efficient Windows Collaborative

Science.gov (United States)

Foundry Foundry New Construction Windows Window Selection Tool Selection Process Design Guidance Installation Replacement Windows Window Selection Tool Assessing Options Selection Process Design Guidance Installation Understanding Windows Benefits Design Considerations Measuring Performance Performance Standards

PERBEDAAN MODALITAS VISUAL, AUDITORIAL DAN KINESTETIK SISWA KELAS X SMK JURUSAN TEKNIK PERMESINAN DAN TEKNIK KENDARAAN RINGAN

Directory of Open Access Journals (Sweden)

Margaretha F. Dian Pratiwi

2015-06-01

Full Text Available Penelitian ini bertujuan untuk mengetahui signifikansi perbedaan modalitas siswa antar Jurusan Teknik Mesin dan Teknik Kendaraan Ringan kelas X SMK Muhammadiyah Salatiga. Subjek penelitian ini adalah seluruh siswa kelas X Jurusan Teknik Mesin dan seluruh siswa Teknik Kendaraan Ringan SMK Muhammadiyah Salatiga. Instrumen yang digunakan adalah kuesioner modalitas belajar. Adapun teknik analisis data menggunakan Chi Square yang diolah dengan program SPSS 16.0 for Windows. Analisis komparatif dengan menggunakan Chi-Square didapat value 9,384 dengan nilai signifikansi 0,009 < 0,01. Dengan demikian, hasil analisis menunjukkan terdapat perbedaan yang sangat signifikan antara modalitas visual, auditorial, kinestetik siswa kelas X Teknik Permesinan dan Teknik Kendaraan Ringan di SMK Muhammadiyah Salatiga.

Design of large aperture, low mass vacuum windows

International Nuclear Information System (INIS)

Leonhardt, W.J.; Mapes, M.

1993-01-01

Large vacuum vessels are employed downstream of fixed targets in High Energy Physics experiments to provide a long path for particles to traverse without interacting with air molecules. These vessels generally have a large aperture opening known as a vacuum window which employs a thin membrane to preserve the vacuum environment yet allows the particles to pass through with a minimal effect on them. Several large windows have been built using a composite of Kevlar/Mylar including circular windows to a diameter of 96.5 cm and rectangular windows up to 193 cm x 86 cm. This paper describes the design, fabrication, testing and operating experience with these windows and relates the actual performance to theoretical predictions

The new null testing method for the special optical window

Science.gov (United States)

Huang, Changchun

2009-07-01

The high speed, high precision and wide range specifications are requirement for the modern aircraft, which the traditional hemispherical dome can't achieve now, and the novel conformal window instead can enhance the aerodynamic performance of the aircraft obviously. To reduce the aerodynamic drag and radar cross-section, the window geometry is generally aspheric in shape. As a result, the involved fabrication and testing processes are much more challenging than that of conventional optics and must be mastered before these windows and systems can be implemented at an acceptable cost and risk. Metrology is one of the critical areas required to advance the conformal window technology. But as the surface of these conformal windows is not the traditional sphere lens, the measurement method for it is infeasible with the conventional optics measurement processes. This paper we express the development of testing technology for the special conformal windows in brief, and emphatically introduces one available novel testing method- a new null testing, and here based on the theory of compensation methods, The principle of Offner's refractive null lens has been extended to test the transmission wavefront through conformal window optics and provide feedback during surface fabrication. a compensator system for the was designed for the conformal window is given which parameters are 100mm for its aperture and two parabolic surface as conformal window, the final residual wavefront error(RMS) of which is less than 1/20λ(λ=632.8nm).

Design and application of CVD diamond windows for x-rays at the Advanced Photon Source

International Nuclear Information System (INIS)

Jaski, Y.; Cookson, D.

2007-01-01

Two types of directly cooled, 0.2-mm-thick, 8-mm-diameter clear aperture CVD diamond windows have been designed and successfully fabricated by two different vendors for use at the Advanced Photon Source (APS). Both windows contain a direct braze joint between the diamond and the cooled OFHC copper. These windows can be used to replace the front-end beryllium windows in high-heat-load applications and can be used as white beam windows in the beamlines. This paper presents the detailed design of the diamond windows, the thermal analysis of the diamond window under different thermal load configurations, as well as a complete list of the existing APS front-end beryllium window configurations and replacement scenarios. Small-angle scattering experiments have been conducted on both diamond windows and a polished beryllium window, and the results are presented.

Generating a Square Switching Window for Timing Jitter Tolerant 160 Gb/s Demultiplexing by the Optical Fourier Transform Technique

DEFF Research Database (Denmark)

Oxenløwe, Leif Katsuo; Galili, Michael; Clausen, A. T:

2006-01-01

A square spectrum is optically Fourier transformed into a square pulse in the time domain. This is used to demultiplex a 160 Gb/s data signal with a significant increase in jitter tolerance to 2.6 ps.......A square spectrum is optically Fourier transformed into a square pulse in the time domain. This is used to demultiplex a 160 Gb/s data signal with a significant increase in jitter tolerance to 2.6 ps....

Superiority of Low Energy 160 KV X-Rays Compared to High Energy 6 MV X-Rays in Heavy Element Radiosensitization for Cancer Treatment

Science.gov (United States)

Lim, Sara N.; Pradhan, Anil K.; Nahar, Sultana N.; Barth, Rolf F.; Yang, Weilian; Nakkula, Robin J.; Palmer, Alycia; Turro, Claudia

2013-06-01

High energy X-rays in the MeV range are generally employed in conventional radiation therapy from linear accelerators (LINAC) to ensure sufficient penetration depths. However, lower energy X-rays in the keV range may be more effective when coupled with heavy element (high-Z or HZ) radiosensitizers. Numerical simulations of X-ray energy deposition for tumor phantoms sensitized with HZ radiosensitizers were performed using the Monte Carlo code Geant4. The results showed enhancement in energy deposition to radiosensitized phantoms relative to unsensitized phantoms for low energy X-rays in the keV range. In contrast, minimal enhancement was seen using high energy X-rays in the MeV range. Dose enhancement factors (DEFs) were computed and showed radiosensitization only in the low energy range nitrate, was initially used because it was 7x less toxic that an equivalent amount of carboplatin in vitro studies. This would allow us to separate the radiotoxic and the chemotoxic effects of HZ sensitizers. Results from this study showed a 10-fold dose dependent reduction in surviving fractions (SF) of radiosensitized cells treated with low energy 160 kV X-rays compared to those treated with 6 MV X-rays. This is in agreement with our simulations that show an increase in dose deposition in radiosensitized tumors for low energy X-rays. Due to unforeen in vivo toxicity, however, another in vitro study was performed using the commonly used, Pt-based chemotherapeutic drug carboplatin which confirmed earlier results. This lays the ground work for a planned in vivo study using F98 glioma bearing rats. This study demonstrates that while high energy X-rays are commonly used in cancer radiotherapy, low energy keV X-rays might be much more effective with HZ radiosensitization.

Ageing, fragility and the reversibility window in bulk alloy glasses

International Nuclear Information System (INIS)

Chakravarty, S; Georgiev, D G; Boolchand, P; Micoulaut, M

2005-01-01

Non-reversing relaxation enthalpies (ΔH nr ) at glass transitions T g (x) in the P x Ge x Se 1-2x ternary display wide, sharp and deep global minima (∼0) in the 0.09 g s become thermally reversing. In this reversibility window, glasses are found not to age, in contrast to ageing observed for fragile glass compositions outside the window. Thermal reversibility and lack of ageing seem to be paradigms of self-organization which molecular glasses share with protein structures which repetitively and reversibly change conformation near T g and the folding temperature respectively. (letter to the editor)

Study on labelling methods of 125I-RC-160 and its biodistribution in animals

International Nuclear Information System (INIS)

Wang Jing; Wang Xiqing; Wang Liangang; Li Fujun; Deng Jinglan

2002-01-01

A method for the iodination of peptide RC-160 with high efficiency was developed. RC-160 was iodinated with N-bromosuccinimide (NBS) as oxidant, the conventional chloramine T (Ch-T) method was used as control. The labelling condition of NBS method was optimized and radiolabelled conjugate 125 I-RC-160 was assessed as follows: no further purification was needed, the measured labelling yield of 125 I-RC-160 was 92% and the specific activity was 1.95 x 10 12 Bq/m mol. The yield increased as the amount of NBS increased. The optimal ratio of RC-160 (μg): 125 I (MBq): NBS(μg) was 3:7.4:1. For Ch-T method, the labelling yield is 56% and specific activity was 0.65 x 10 12 Bq/m mol; but after purification by SepPak-C 18 , the labelling yield may reach as high as 92%. 1h after injection, radioactivity in blood decreased by 87.2%. No obvious concentration of 125 I-RC-160 in thyroid or kidney was observed

Evaluation for the retention of reproductive structures by Bt and non ...

African Journals Online (AJOL)

The retention of the reproductive structures (bolls) was evaluated at 90,120 and 160 days of maturity in eight Bt and non-Bt hybrids from three Private R&D establishments on three dates of sowings (90,120 and 160 days of maturity) and two spacings of 67.5 x 60 cm and 100 x 30 cm. Ankur group Bt hybrids; 651, 2226 and ...

Taking snapshots of photoexcited molecules in disordered media using pulsed synchrotron x-rays

International Nuclear Information System (INIS)

Chen, L.X.

2004-01-01

Photoexcited molecules are quintessential reactants in photochemistry. Structures of these photoexcited molecules in disordered media in which a majority of photochemical reactions take place remained elusive for decades owing to a lack of suitable X-ray sources, despite their importance in understanding fundamental aspects in photochemistry. As new pulsed X-ray sources become available, short-lived excited-state molecular structures in disordered media can now be captured by using laser-pulse pump, X-ray pulse-probe techniques of third-generation synchrotron sources with time resolutions of 30-100 ps, as demonstrated by examples in this review. These studies provide unprecedented information on structural origins of molecular properties in the excited states. By using other ultrafast X-ray facilities that will be completed in the near future, time-resolution for the excited-state structure measurements should reach the femtosecond timescales, which will make 'molecular movies' of bond breaking or formation, and vibrational relaxation, a reality.

Proper Installation of Replacement Windows | Efficient Windows

Science.gov (United States)

Collaborative Foundry Foundry New Construction Windows Window Selection Tool Selection Process Design Guidance Installation Replacement Windows Window Selection Tool Assessing Options Selection Process Design Guidance Installation Understanding Windows Benefits Design Considerations Measuring

Performance Standards for Windows | Efficient Windows Collaborative

Science.gov (United States)

Foundry Foundry New Construction Windows Window Selection Tool Selection Process Design Guidance Installation Replacement Windows Window Selection Tool Assessing Options Selection Process Design Guidance Installation Understanding Windows Benefits Design Considerations Measuring Performance Performance Standards

Benefits of Efficient Windows | Efficient Windows Collaborative

Science.gov (United States)

Foundry Foundry New Construction Windows Window Selection Tool Selection Process Design Guidance Installation Replacement Windows Window Selection Tool Assessing Options Selection Process Design Guidance Installation Understanding Windows Benefits Design Considerations Measuring Performance Performance Standards

Assessing Window Replacement Options | Efficient Windows Collaborative

Science.gov (United States)

Foundry Foundry New Construction Windows Window Selection Tool Selection Process Design Guidance Installation Replacement Windows Window Selection Tool Assessing Options Selection Process Design Guidance Installation Understanding Windows Benefits Design Considerations Measuring Performance Performance Standards

Windows for New Construction | Efficient Windows Collaborative

Science.gov (United States)

Foundry Foundry New Construction Windows Window Selection Tool Selection Process Design Guidance Installation Replacement Windows Window Selection Tool Assessing Options Selection Process Design Guidance Installation Understanding Windows Benefits Design Considerations Measuring Performance Performance Standards

Analysis of surface contaminants on beryllium and aluminum windows

International Nuclear Information System (INIS)

Gmur, N.F.

1987-06-01

An effort has been made to document the types of contamination which form on beryllium window surfaces due to interaction with a synchrotron radiation beam. Beryllium windows contaminated in a variety of ways (exposure to water and air) exhibited surface powders, gels, crystals and liquid droplets. These contaminants were analyzed by electron diffraction, electron energy loss spectroscopy, energy dispersive x-ray spectroscopy and wet chemical methods. Materials found on window surfaces include beryllium oxide, amorphous carbon, cuprous oxide, metallic copper and nitric acid. Aluminum window surface contaminants were also examined

Filter and window behavior for the Advanced Photon Source beamline front end

International Nuclear Information System (INIS)

Wang, Zhibi; Kuzay, T.M.; Shu, Deming; Dejus, R.

1993-01-01

Synchrotron x-ray windows are vacuum separators and are usually made of thin beryllium metal. Filters are provided upstream to absorb the soft x-rays so that the window is protected from overheating, which could result in failure. The filters are made of thin carbon products or sometimes beryllium, the same material as the window. Because the window is a vacuum separator, understanding its potential structural failure under thermal load is of utmost importance. The planned insertion devices and bending magnets for the Advanced Photon Source (APS) generate very high heat fluxes. To guarantee the integrity of the filter and window, extensive investigations have been carried out on both components. The material selection for filters and windows from among the possible candidate materials was investigated first. Then a series of thermal and structural analyses were performed on the filter and window. Results are presented from power absorption, analytical results from thermal, and structural analyses as well as application of the failure criteria suggested by Wang and Kuzay to the filters and windows

Fabrication of Microcapsules for Dye-Doped Polymer-Dispersed Liquid Crystal-Based Smart Windows.

Science.gov (United States)

Kim, Mingyun; Park, Kyun Joo; Seok, Seunghwan; Ok, Jong Min; Jung, Hee-Tae; Choe, Jaehoon; Kim, Do Hyun

2015-08-19

A dye-doped polymer-dispersed liquid crystal (PDLC) is an attractive material for application in smart windows. Smart windows using a PDLC can be operated simply and have a high contrast ratio compared to those of other devices that employed photochromic or thermochromic material. However, in conventional dye-doped PDLC methods, dye contamination can cause problems and has a limited degree of commercialization of electric smart windows. Here, we report on an approach to resolve dye-related problems by encapsulating the dye in monodispersed capsules. By encapsulation, a fabricated dye-doped PDLC had a contrast ratio of >120 at 600 nm. This fabrication method of encapsulating the dye in a core-shell structured microcapsule in a dye-doped PDLC device provides a practical platform for dye-doped PDLC-based smart windows.

A deep X-ray view of the bare AGN Ark 120. IV. XMM-Newton and NuSTAR spectra dominated by two temperature (warm, hot) Comptonization processes

Science.gov (United States)

Porquet, D.; Reeves, J. N.; Matt, G.; Marinucci, A.; Nardini, E.; Braito, V.; Lobban, A.; Ballantyne, D. R.; Boggs, S. E.; Christensen, F. E.; Dauser, T.; Farrah, D.; Garcia, J.; Hailey, C. J.; Harrison, F.; Stern, D.; Tortosa, A.; Ursini, F.; Zhang, W. W.

2018-01-01

Context. The physical characteristics of the material closest to supermassive black holes (SMBHs) are primarily studied through X-ray observations. However, the origins of the main X-ray components such as the soft X-ray excess, the Fe Kα line complex, and the hard X-ray excess are still hotly debated. This is particularly problematic for active galactic nuclei (AGN) showing a significant intrinsic absorption, either warm or neutral, which can severely distort the observed continuum. Therefore, AGN with no (or very weak) intrinsic absorption along the line of sight, so-called "bare AGN", are the best targets to directly probe matter very close to the SMBH. Aims: We perform an X-ray spectral analysis of the brightest and cleanest bare AGN known so far, Ark 120, in order to determine the process(es) at work in the vicinity of the SMBH. Methods: We present spectral analyses of data from an extensive campaign observing Ark 120 in X-rays with XMM-Newton (4 × 120 ks, 2014 March 18-24), and NuSTAR (65.5 ks, 2014 March 22). Results: During this very deep X-ray campaign, the source was caught in a high-flux state similar to the earlier 2003 XMM-Newton observation, and about twice as bright as the lower-flux observation in 2013. The spectral analysis confirms the "softer when brighter" behavior of Ark 120. The four XMM-Newton/pn spectra are characterized by the presence of a prominent soft X-ray excess and a significant Fe Kα complex. The continuum is very similar above about 3 keV, while significant variability is present for the soft X-ray excess. We find that relativistic reflection from a constant-density, flat accretion disk cannot simultaneously produce the soft excess, broad Fe Kα complex, and hard X-ray excess. Instead, Comptonization reproduces the broadband (0.3-79 keV) continuum well, together with a contribution from a mildly relativistic disk reflection spectrum. Conclusions: During this 2014 observational campaign, the soft X-ray spectrum of Ark 120 below 0

VIS-IR transmitting BGG glass windows

Science.gov (United States)

Bayya, Shyam S.; Chin, Geoff D.; Sanghera, Jasbinder S.; Aggarwal, Ishwar D.

2003-09-01

BaO-Ga2O3-GeO2 (BGG) glasses have the desired properties for various window applications in the 0.5-5 μm wavelength region. These glasses are low cost alternatives to the currently used window materials. Fabrication of a high optical quality 18" diameter BGG glass window has been demonstrated with a transmitted wave front error of λ/10 at 632 nm. BGG substrates have also been successfully tested for environmental weatherability (MIL-F-48616) and rain erosion durability up to 300 mph. Preliminary EMI grids have been successfully applied on BGG glasses demonstrating attenuation of 20dB in X and Ku bands. Although the mechanical properties of BGG glasses are acceptable for various window applications, it is demonstrated here that the properties can be further improved significantly by the glassceramization process. The ceramization process does not add any significant cost to the final window material. The crystallite size in the present glass-ceramic limits its transmission to the 2-5 μm region.

Bright circularly polarized soft X-ray high harmonics for X-ray magnetic circular dichroism.

Science.gov (United States)

Fan, Tingting; Grychtol, Patrik; Knut, Ronny; Hernández-García, Carlos; Hickstein, Daniel D; Zusin, Dmitriy; Gentry, Christian; Dollar, Franklin J; Mancuso, Christopher A; Hogle, Craig W; Kfir, Ofer; Legut, Dominik; Carva, Karel; Ellis, Jennifer L; Dorney, Kevin M; Chen, Cong; Shpyrko, Oleg G; Fullerton, Eric E; Cohen, Oren; Oppeneer, Peter M; Milošević, Dejan B; Becker, Andreas; Jaroń-Becker, Agnieszka A; Popmintchev, Tenio; Murnane, Margaret M; Kapteyn, Henry C

2015-11-17

We demonstrate, to our knowledge, the first bright circularly polarized high-harmonic beams in the soft X-ray region of the electromagnetic spectrum, and use them to implement X-ray magnetic circular dichroism measurements in a tabletop-scale setup. Using counterrotating circularly polarized laser fields at 1.3 and 0.79 µm, we generate circularly polarized harmonics with photon energies exceeding 160 eV. The harmonic spectra emerge as a sequence of closely spaced pairs of left and right circularly polarized peaks, with energies determined by conservation of energy and spin angular momentum. We explain the single-atom and macroscopic physics by identifying the dominant electron quantum trajectories and optimal phase-matching conditions. The first advanced phase-matched propagation simulations for circularly polarized harmonics reveal the influence of the finite phase-matching temporal window on the spectrum, as well as the unique polarization-shaped attosecond pulse train. Finally, we use, to our knowledge, the first tabletop X-ray magnetic circular dichroism measurements at the N4,5 absorption edges of Gd to validate the high degree of circularity, brightness, and stability of this light source. These results demonstrate the feasibility of manipulating the polarization, spectrum, and temporal shape of high harmonics in the soft X-ray region by manipulating the driving laser waveform.

Mucosal pathology of an experimental otitis media with effusion after X-ray irradiation

International Nuclear Information System (INIS)

Ohashi, Y.; Nakai, Y.; Ikeoka, H.; Esaki, Y.; Koshimo, H.; Onoyama, Y.

1987-01-01

Ten guinea pigs were irradiated with 30 Gy of x-radiation. Five were killed on the eighth day after irradiation, and the remainder were killed at the sixteenth day after irradiation. At the time of death, examination was made of the ciliary activity and the fine structure of the middle ear mucosa. Serous effusion was found in each tympanic cavity of all animals. It was shown also that the guinea pig, when irradiated with 30 Gy of x-radiation, exhibits pathologic abnormalities similar to those in humans with otitis media with effusion: degeneration of cilia or ciliated cells and changes in the vascular system (capillary injury and increased capillary permeability). Functional examinations showed that x-ray irradiation has delayed effects on ciliary activity, and the effects are much greater at the sixteenth day than at the eighth day. We speculate that the accumulation of effusion can be, at least partially, a consequence of ciliary dysfunction. The induction of sterile effusion by the use of x-ray irradiation provides a unique animal model for chronic otitis media with effusion of the serous type

A virtual control panel configuration tool for the X-Window system

International Nuclear Information System (INIS)

Hill, J.O.; Dalesio, L.R.; Kerstiens, D.M.

1992-01-01

Computer Graphics Workstations are becoming increasingly popular for use as virtual process control and read back panels. The workstation's CRT, keyboard, and pointing device are used in concert to produce a display that is in essence a control panel, even if actual switches and gauges are not present. The code behind these displays is most often specific to one display and not reusable for any other display. Recently, programs have been written allowing many of these virtual control panel displays to be configured without writing additional code. This approach allows the initial programming effort to be reapplied to many different display instances with minimal effort. These programs often incorporate many of the features of a graphics editor, allowing a pictorial model of the process under control to be incorporated into the control panel. We have just finished writing a second generation software system of this type for use with the X-window system and the Experimental Physics and Industrial Control System (EPICS). This paper describes the primary features of our software, the framework of our design, and our observations after initial installation. (author)

Opoku Buabeng

African Journals Online (AJOL)

PUBLICATIONS1

In children with swallowed foreign bodies, the incidence in males and ... Currently the flexible endoscopic removal with video-imaging is ... the social scientists (SPSS) 16.0 for Windows. Product. .... lic awareness through the media, in schools.

Replacement Windows for Existing Homes Homes | Efficient Windows

Science.gov (United States)

Collaborative Foundry Foundry New Construction Windows Window Selection Tool Selection Process Design Guidance Installation Replacement Windows Window Selection Tool Assessing Options Selection Process Design Guidance Installation Understanding Windows Benefits Design Considerations Measuring

Pengembangan Media Ice Breaker Talking Pen pada Mata Pelajaran PAI Kelas X SMAN 100 Jakarta

Directory of Open Access Journals (Sweden)

Ati Sulastri

2017-07-01

Full Text Available This study aims to find out how to develop media ice breaker talking pen and media feasibility on the subjects of PAI. The research method used is Borg and Gall development model which includes requirement analysis, validation test, and test phase. The result of this development research is ice breaker talking pen media product which consists of command card and music developed through data collection, planning, product development, and validation and testing. Based on the validation results obtained the average score of the material experts of 4.75 (very good, and from the media experts of 3.78 (good, and the results of student responses about this media amounted to 4.39 or very good category. Therefore the ice breaker talking media on the eyes of learning PAI class X is declared eligible for use with very good category. Keywords: Development Model  Study, Ice Breaker Talking Pen, PAI Abstrak Penelitian ini bertujuan untuk mengetahui cara mengembangkan media ice breaker talking pen dan kelayakan media tersebut pada mata pelajaran PAI. Metode yang digunakan adalah model pengembangan Borg dan Gall yang meliputi analisis kebutuhan, tahap validasi dan tahap uji coba. Hasil penelitian pengembangan ini adalah produk media ice breaker talking pen yang terdiri dari kartu perintah dan musik yang dikembangkan melalui tahap pengumpulan data, perencanaan, pengembangan produk, serta validasi dan uji coba. Berdasarkan pada hasil validasi didapat skor rata-rata dari ahli materi sebesar 4,75 (sangat baik, dan dari ahli media sebesar 3,78 (baik. Serta hasil dari tanggapan siswa mengenai media ini sebesar 4,39 atau kategori sangat baik. Maka dari itu media ice breaker talking pen pada mata pelajaran PAI kelas X dinyatakan layak untuk digunakan dengan kategori sangat baik. Kata Kunci : Pengembangan Model Pembelajaran, Ice Breaker Talking Pen, PAI

Design Guidance for New Windows | Efficient Windows Collaborative

Science.gov (United States)

Foundry Foundry New Construction Windows Window Selection Tool Selection Process Design Guidance Installation Replacement Windows Window Selection Tool Assessing Options Selection Process Design Guidance Installation Understanding Windows Benefits Design Considerations Measuring Performance Performance Standards

Selection Process for New Windows | Efficient Windows Collaborative

Science.gov (United States)

Foundry Foundry New Construction Windows Window Selection Tool Selection Process Design Guidance Installation Replacement Windows Window Selection Tool Assessing Options Selection Process Design Guidance Installation Understanding Windows Benefits Design Considerations Measuring Performance Performance Standards

Selection Process for Replacement Windows | Efficient Windows Collaborative

Science.gov (United States)

Foundry Foundry New Construction Windows Window Selection Tool Selection Process Design Guidance Installation Replacement Windows Window Selection Tool Assessing Options Selection Process Design Guidance Installation Understanding Windows Benefits Design Considerations Measuring Performance Performance Standards

Design Guidance for Replacement Windows | Efficient Windows Collaborative

Science.gov (United States)

Foundry Foundry New Construction Windows Window Selection Tool Selection Process Design Guidance Installation Replacement Windows Window Selection Tool Assessing Options Selection Process Design Guidance Installation Understanding Windows Benefits Design Considerations Measuring Performance Performance Standards

Proper Installation of New Windows | Efficient Windows Collaborative

Science.gov (United States)

Foundry Foundry New Construction Windows Window Selection Tool Selection Process Design Guidance Installation Replacement Windows Window Selection Tool Assessing Options Selection Process Design Guidance Installation Understanding Windows Benefits Design Considerations Measuring Performance Performance Standards

An Experimental and Analytical Evaluation of Wall And Window Retrofit Configurations: Supporting the Residential Retrofit Best Practices Guide

Energy Technology Data Exchange (ETDEWEB)

Stovall, Therese K [ORNL; Petrie, Thomas [ORNL; Kosny, Jan [ORNL; Childs, Phillip W [ORNL; Atchley, Jerald Allen [ORNL; Hulvey, Kimberly D [ORNL

2007-11-01

A Retrofit Best Practices Guide was developed to encourage homeowners to consider energy conservation issues whenever they modify their siding or windows. In support of this guide, an experimental program was implemented to measure the performance of a number of possible wall siding and window retrofit configurations. Both thermal and air-leakage measurements were made for a 2.4 x 2.4 m (8 x 8 ft) wall section with and without a 0.9 x 1.2 m (3 x 4 ft) window. The windows tested were previously well-characterized at a dedicated window test facility. A computer model was also used to provide information for the Best Practices Guide. The experimental data for walls and windows were used in conjunction with this model to estimate the total annual energy savings for several typical houses in a number of different locations.

Smart windows based on cholesteric liquid crystals (Conference Presentation)

Science.gov (United States)

Khandelwal, Hitesh; Debije, Michael G.; Schenning, Albert P. H. J.

2017-02-01

With increase in global warming, use of active cooling and heating devices are continuously increasing to maintain interior temperature of built environment, greenhouses and cars. To reduce the consumption of tremendous amount of energy on cooling and heating devices we need an improved control of transparent features (i.e. windows). In this respect, smart window which is capable for reflecting solar infrared energy without interfering with the visible light would be very attractive. Most of the technologies developed so far are to control the visible light. These technologies block visual contact to the outside world which cause negative effects on human health. An appealing method to selectively control infrared transmission is via utilizing the reflection properties of cholesteric liquid crystals. In our research, we have fabricated a smart window which is capable of reflecting different amount of solar infrared energy depending on the specific climate conditions. The reflection bandwidth can be tuned from 120 nm to 1100 nm in the infrared region without interfering with the visible solar radiations. Calculations reveal that between 8% and 45% of incident solar infrared light can be reflected with a single cell. Simulation studies predicted that more than 12% of the energy spent on heating, cooling and lighting in the built environment can be saved by using the fabricated smart window compared to standard double glazing window.

Optimal scanning time window for 18F-FP-(+)-DTBZ (18F-AV-133) summed uptake measurements

International Nuclear Information System (INIS)

Lin, Kun-Ju; Lin, Wey-Yil; Hsieh, Chia-Ju; Weng, Yi-Hsin; Wey, Shiaw-Pyng; Lu, Chin-Song; Skovronsky, Daniel; Yen, Tzu-Chen; Chang, Chee-Jen; Kung, Mei-Ping

2011-01-01

18 F-9-fluoropropyl-(+)-dihydrotetrabenazine ( 18 F-AV-133) is a novel positron emission tomography tracer for imaging the vesicular monoamine transporter II in dopaminergic neuron degeneration, which might be indicative for Parkinson's disease (PD) and other parkinsonism. Studies were performed to optimize the imaging time window for calculating standardized uptake value ratio (SUVR) with correlation to distribution volume ratio (DVR) and in differentiating PD from normal controls (NCs). Methods: Thirteen 18 F-AV-133 positron emission tomography studies were conducted on four NCs (age, 62.3±4.9 years) and nine PD patients (age, 60.8±6.0 years) with Hoehn and Yahr stages 2 to 3. Dynamic images were acquired within 180 min (0–30, 50–140 and 160–180 min) and were rearranged into 14 of 10-min scans. The contralateral striatum was defined as the opposite striatum to the predominantly affected limbs. Volumes of interest (VOIs) of bilateral putamen, caudate nuclei and occipital cortex (OC; as the reference region) were delineated from individual magnetic resonance imaging. SUVRs of striatum to OC were computed from 14 dynamic image sets. The DVRs were computed from Logan graphic analysis by using OC as the input. The performance of SUVR was evaluated based on the correlation of SUVR at each time window to DVR, as well as the Cohen effect size (group mean SUVR difference between PD and NC/standard deviation). Results: 18 F-AV-133 uptake decreased in PD subjects at bilateral striatum especially at contralateral side with posterior putamen predominant as compared with NC. Consistent higher correlations of SUVRs to DVR for all VOIs were observed at later time window and reached to its maximal value of 0.9917 at 90–100 min. The group mean SUVR differences between NC and PD subjects increased and reached relatively stable values after 90 min. The effect sizes for all VOIs were stable across different time window and with the largest value around 90∼120 min

Design of large aperture, low mass vacuum windows

International Nuclear Information System (INIS)

Leonhardt, W.J.; Mapes, M.

1993-01-01

Large vacuum vessels are employed downstream of fixed targets in High Energy Physics experiments to provide a long path for particles to transverse without interacting with air molecules. These vessels generally have a large aperture opening known as a open-quotes vacuum windowclose quotes which employs a thin membrane to preserve the vacuum environment yet allows the particles to pass through with a minimal effect on them. Several large windows have been built using a composite of Kevlar/Mylar including circular windows to a diameter of 96.5 cm and rectangular windows up to 193 cm x 86 cm. This paper describes the design, fabrication, testing and operating experience with these windows and relates the actual performance to theoretical predictions

Investigation of cooling methods and thickness considerations in the filter/window assembly for synchrotron radiation beamlines

International Nuclear Information System (INIS)

Wang, Z.; Kuzay, T.M.; Hahn, U.

1993-01-01

Synchrotron x-ray windows are vacuum separators and are usually made of thin beryllium metal. Filters are provided upstream to absorb the soft x-rays so that the window can be protected from overheating, which could result in failure. The filters are made of thin carbon products or sometimes beryllium, the same material as the window. When the synchrotron x-rays pass through a filter or window, part of the photons will be absorbed by the filter or window. The absorbed photons cause heat to build up within the filter or window. Successful filter and window designs should effectively dissipate the heat generated by the absorbed photons and guarantee the safety of the filter and window. The cooling methods typically used in a filter or window design are conduction and radiation cooling or a combination of the two. The different cooling methods were first examined with regard to efficiency and effectiveness in different temperature ranges. Analysis results are presented for temperature distribution and corresponding thermal stresses in the filter and window. Another important issue to be resolved in designing a filter/window assembly is how to select the thickness of the filters and windows. This paper focuses on the criteria for choosing the thickness of a filter: whether it is better to use a few thick filters or a series of thin ones; how to determine the minimum/maximum thickness; and the difference in thickness considerations for the window versus the filter. Numerical investigations are presented

Lobster eye as a collector for water window microscopy

Science.gov (United States)

Pina, L.; Maršíková, V.; Inneman, A.; Nawaz, M. F.; Jančárek, A.; Havlíková, R.

2017-08-01

Imaging in EUV, SXR and XR spectral bands of radiation is of increasing interest. Material science, biology and hot plasma are examples of relevant fast developing areas. Applications include spectroscopy, astrophysics, Soft X-ray Ray metrology, Water Window microscopy, radiography and tomography. Especially Water Window imaging has still not fully recognized potential in biology and medicine microscopy applications. Theoretical study and design of Lobster Eye (LE) optics as a collector for water window (WW) microscopy and comparison with a similar size ellipsoidal mirror condensor are presented.

Professional Windows Embedded Compact 7

CERN Document Server

Phung, Samuel; Joubert, Thierry; Hall, Mike

2011-01-01

Learn to program an array of customized devices and solutions As a compact, highly efficient, scalable operating system, Windows Embedded Compact 7 (WEC7) is one of the best options for developing a new generation of network-enabled, media-rich, and service-oriented devices. This in-depth resource takes you through the benefits and capabilities of WEC7 so that you can start using this performance development platform today. Divided into several major sections, the book begins with an introduction and then moves on to coverage of OS design, application development, advanced application developm

The replacement of touch-terminal consoles of the CERN antiproton accumulator complex (AAC) by office PC's as well as X-windows based workstations

International Nuclear Information System (INIS)

Chohan, V.; Deloose, I.; Shering, G.

1992-01-01

With aging hardware and expensive maintenance and replacement possibilities, it was decided to upgrade the AAC touch terminal consoles with modern hardware. With significant amount of operational application software developed with touch terminals over 10 years, the philosophy adopted was to attempt a total emulation of these console functions of touch actions, graphics display as well as simple keyboard terminal entry onto the front-end computer controlling the AAC. The PC based emulation by mouse and multiple windows under MS-DOS and later, under the Windows 3 environment was realized relatively quickly; the next stage was therefore to do the same on the Unix platform using software based on X-windows. The communications channel was established using the TCP/IP socket library. This paper reviews this work up to the operational implementation for routine control room usage for both these solutions. (author)

Locating the scala media in the fixed human temporal bone for therapeutic access: a preliminary study.

Science.gov (United States)

Pau, H; Fagan, P; Oleskevich, S

2006-11-01

To investigate the location of the scala media in relation to the round window niche in human temporal bones. Ten human temporal bones were investigated by radical mastoidectomy and promontory drill-out. Temporal bone laboratory. The distance from the scala media to the anterior edge of the round window niche, measured by Fisch's stapedectomy measuring cylinders. The scala media was identified at the transection point of a vertical line 1.6 to 2.2 mm (mean=1.8 mm; standard deviation=0.2) anterior to the anterior edge of the round window niche and a horizontal line 0.2 mm inferior to the lower border of the oval window. This report demonstrates the point of entry into the scala media via the promontory in fixed temporal bone models, which may provide a site of entry for stem cells and gene therapy insertion.

Windows

DEFF Research Database (Denmark)

Heiselberg, Per; Svidt, Kjeld; Nielsen, Peter V.

In natural ventilation systems fresh air is often provided through opening of windows. However, the knowledge of the performance of windows is rather limited. Computation of natural ventilation air flow through windows is most commonly made using discharge coefficients, that are regarded as being...... constant. The reported results show that the discharge coefficient for a window opening cannot be regarded as a constant and that it varies considerably with the size of the opening area, the window type and the temperature difference. Therefore, the use of a constant value can lead to serious errors...

Developement of EBM from x-ray machine

International Nuclear Information System (INIS)

Muhamad Zahidee Taat; Leo Kwee Wah; Mohd Rizal Md Chulan; Abu Bakar Ghazali; Razali Hamzah; Abu Bakar Harun; Wan Hadi Wan Abu Bakar; Mohd Rizal Mamat

2004-01-01

This paper explains the works being done to convert an old x-ray machine into a low energy electron beam accelerator. In this project, we replace the x-ray tube from the machine with an electron accelerating tube while maintaining the high voltage power supply of 160 kV. Components involved in this project development are understanding the physics of accelerated particles, designing the ultra high vacuum system of at least 10-6 torr to vacuum the tube, assembling the high voltage supply and electron gun to accelerator tube and installing a thin titanium at the end of the tube as a window for the electrons to escape to atmosphere. Two stages of pumping are needed to meet the vacuum requirement; the first is for rough pumping down to 10 -3 torr and then subsequently switching to the second stage that continues pumping to reach the required level. For the first stage, we use a rotary pump and for the later either a turbo molecular pump or a diffusion pump. Furthermore, it is also essential to design and fabricate a connector with suitable insulation material to connect the high tension (HT) cable from the x-ray machine with the cathode of the accelerating tube. The electrons that escape from the window into atmosphere are collected and measured using a faraday cup meter. We expect to get some initial data from this setup before the seminar and hopefully will present it together with the theoretical calculation and design of the main components. (Author)

Dynamics of a Z-pinch x-ray source for heating inertial-confinement-fusion relevant hohlraums to 120--160 eV

Energy Technology Data Exchange (ETDEWEB)

Sanford, T. W. L.; Olson, R. E.; Mock, R. C.; Chandler, G. A.; Leeper, R. J.; Nash, T. J.; Ruggles, L. E.; Simpson, W. W.; Struve, K. W.; Peterson, D. L. (and others)

2000-11-01

A Z-pinch radiation source has been developed that generates 60{+-}20 kJ of x rays with a peak power of 13{+-}4 TW through a 4-mm-diam axial aperture on the Z facility. The source has heated National Ignition Facility-scale (6-mm-diam by 7-mm-high) hohlraums to 122{+-}6 eV and reduced-scale (4-mm-diam by 4-mm-high) hohlraums to 155{+-}8 eV -- providing environments suitable for indirect-drive inertial confinement fusion studies. Eulerian-RMHC (radiation-magnetohydrodynamics code) simulations that take into account the development of the Rayleigh--Taylor instability in the r--z plane provide integrated calculations of the implosion, x-ray generation, and hohlraum heating, as well as estimates of wall motion and plasma fill within the hohlraums. Lagrangian-RMHC simulations suggest that the addition of a 6 mg/cm3 CH{sub 2} fill in the reduced-scale hohlraum decreases hohlraum inner-wall velocity by {approx}40% with only a 3%--5% decrease in peak temperature, in agreement with measurements.

Dynamics of a Z-pinch x-ray source for heating inertial-confinement-fusion relevant hohlraums to 120--160 eV

International Nuclear Information System (INIS)

Sanford, T. W. L.; Olson, R. E.; Mock, R. C.; Chandler, G. A.; Leeper, R. J.; Nash, T. J.; Ruggles, L. E.; Simpson, W. W.; Struve, K. W.; Peterson, D. L.

2000-01-01

A Z-pinch radiation source has been developed that generates 60±20 kJ of x rays with a peak power of 13±4 TW through a 4-mm-diam axial aperture on the Z facility. The source has heated National Ignition Facility-scale (6-mm-diam by 7-mm-high) hohlraums to 122±6 eV and reduced-scale (4-mm-diam by 4-mm-high) hohlraums to 155±8 eV -- providing environments suitable for indirect-drive inertial confinement fusion studies. Eulerian-RMHC (radiation-magnetohydrodynamics code) simulations that take into account the development of the Rayleigh--Taylor instability in the r--z plane provide integrated calculations of the implosion, x-ray generation, and hohlraum heating, as well as estimates of wall motion and plasma fill within the hohlraums. Lagrangian-RMHC simulations suggest that the addition of a 6 mg/cm3 CH 2 fill in the reduced-scale hohlraum decreases hohlraum inner-wall velocity by ∼40% with only a 3%--5% decrease in peak temperature, in agreement with measurements

Dynamics of a Z-pinch x-ray source for heating inertial-confinement-fusion relevant hohlraums to 120-160 eV

Science.gov (United States)

Sanford, T. W. L.; Olson, R. E.; Mock, R. C.; Chandler, G. A.; Leeper, R. J.; Nash, T. J.; Ruggles, L. E.; Simpson, W. W.; Struve, K. W.; Peterson, D. L.; Bowers, R. L.; Matuska, W.

2000-11-01

A Z-pinch radiation source has been developed that generates 60±20 kJ of x rays with a peak power of 13±4 TW through a 4-mm-diam axial aperture on the Z facility. The source has heated National Ignition Facility-scale (6-mm-diam by 7-mm-high) hohlraums to 122±6 eV and reduced-scale (4-mm-diam by 4-mm-high) hohlraums to 155±8 eV—providing environments suitable for indirect-drive inertial confinement fusion studies. Eulerian-RMHC (radiation-magnetohydrodynamics code) simulations that take into account the development of the Rayleigh-Taylor instability in the r-z plane provide integrated calculations of the implosion, x-ray generation, and hohlraum heating, as well as estimates of wall motion and plasma fill within the hohlraums. Lagrangian-RMHC simulations suggest that the addition of a 6 mg/cm3 CH2 fill in the reduced-scale hohlraum decreases hohlraum inner-wall velocity by ˜40% with only a 3%-5% decrease in peak temperature, in agreement with measurements.

Scanning transmission x-ray microscope for materials science spectromicroscopy at the ALS

Energy Technology Data Exchange (ETDEWEB)

Warwick, T.; Seal, S.; Shin, H. [Ernest Orlando Lawrence Berkeley National Lab., CA (United States)] [and others

1997-04-01

The brightness of the Advanced Light Source will be exploited by several new instruments for materials science spectromicroscopy over the next year or so. The first of these to become operational is a scanning transmission x-ray microscope with which near edge x-ray absorption spectra (NEXAFS) can be measured on spatial features of sub-micron size. Here the authors describe the instrument as it is presently implemented, its capabilities, some studies made to date and the developments to come. The Scanning Transmission X-ray Microscope makes use of a zone plate lens to produce a small x-ray spot with which to perform absorption spectroscopy through thin samples. The x-ray beam from ALS undulator beamline 7.0 emerges into the microscope vessel through a silicon nitride vacuum window 160nm thick and 300{mu}m square. The vessel is filled with helium at atmospheric pressure. The zone plate lens is illuminated 1mm downstream from the vacuum window and forms an image in first order of a pinhole which is 3m upstream in the beamline. An order sorting aperture passes the first order converging light and blocks the unfocused zero order. The sample is at the focus a few mm downstream of the zone plate and mounted from a scanning piezo stage which rasters in x and y so that an image is formed, pixel by pixel, by an intensity detector behind the sample. Absorption spectra are measured point-by-point as the photon energy is scanned by rotating the diffraction grating in the monochromator and changing the undulator gap.

Sixa-silicon x-ray array

International Nuclear Information System (INIS)

Taylor, I.

1995-01-01

Full text: The Spectrum-X-Gamma (SRG) satellite is scheduled for launch in 1995-96. Mission objectives include broad and narrow band imaging spectroscopy over a wide range of energies from the EUV through hard X-rays with an emphasis on studying galactic and extragalactic X-ray sources. Timing and moderate resolution spectroscopy can be performed with the solid state spectrometer SIXA (Silicon X-Ray Array), placed on the focal plane of the SODART telescope with total effective area of 1150 cm 2 at 6 keV (for f = 8 in telescope). The detector consists of 19 circular Si(Li) pixels, each with an active diameter of 9.2 min and thickness of 3 min. A radiative cooler will be used to bring the detector to the proper operating temperature (120-130 K). The energy range 0.5-20 keV is divided into 1024 channels of 20 eV size. Photons can be recorded with 30 μs time resolution and 160-200 eV (1-7 keV) energy resolution. Potential observing programmes (for e.g. time-resolved Iron Kα line spectroscopy) include stellar coronae, cataclysmic variables and X-ray binaries; accretion discs and coronae of neutron stars and black hole candidates; supernova remnants, active galactic nuclei and clusters of galaxies. (author)

Inductive Sensor for Lightning Current Measurement, Fitted in Aircraft Windows-Part I: Analysis for a Circular Window

Czech Academy of Sciences Publication Activity Database

van Deursen, A.P.J.; Stelmashuk, Vitaliy

2011-01-01

Roč. 11, č. 1 (2011), s. 199-204 ISSN 1530-437X Institutional research plan: CEZ:AV0Z20430508 Keywords : Lightning * inductive sensor * aircraft * window * viewport Subject RIV: JB - Sensors , Measurment, Regulation Impact factor: 1.520, year: 2011

53 W average power few-cycle fiber laser system generating soft x rays up to the water window.

Science.gov (United States)

Rothhardt, Jan; Hädrich, Steffen; Klenke, Arno; Demmler, Stefan; Hoffmann, Armin; Gotschall, Thomas; Eidam, Tino; Krebs, Manuel; Limpert, Jens; Tünnermann, Andreas

2014-09-01

We report on a few-cycle laser system delivering sub-8-fs pulses with 353 μJ pulse energy and 25 GW of peak power at up to 150 kHz repetition rate. The corresponding average output power is as high as 53 W, which represents the highest average power obtained from any few-cycle laser architecture so far. The combination of both high average and high peak power provides unique opportunities for applications. We demonstrate high harmonic generation up to the water window and record-high photon flux in the soft x-ray spectral region. This tabletop source of high-photon flux soft x rays will, for example, enable coherent diffractive imaging with sub-10-nm resolution in the near future.

Analyzing three-dimensional position of region of interest using an image of contrast media using unilateral X-ray exposure

International Nuclear Information System (INIS)

Harauchi, Hajime; Gotou, Hiroshi; Tanooka, Masao

1994-01-01

Analyzing three-dimensional internal structure of object in an X-ray study is usually performed by using two or more of the incidents of an X-ray direction. In this report, we analyzed the three-dimensional position of tubes with a phantom by using both contrast media and imaging of one direction in the X-ray study. The concentration of the iodine in contrast media can be known by using the log-subtraction image of only the one-directional incident X-ray. Also the diameter of tube filled with contrast media is calculated by the concentration of iodine. So we can show the three-dimensional position of tubes geometrically, by the diameter of tube and the measured value of the film. We verified this method by an experiment according to the theory. (author)

PENGEMBANGAN MEDIA MOVIE MAKER PADA MATA PELAJARAN KEARSIPAN KELAS X ADMINISTRASI PERKANTORAN

Directory of Open Access Journals (Sweden)

Fika Dwi Rahmania

2016-07-01

Full Text Available Abstract: The purpose of this research is the instructional medium movie maker in the basic competence that is Identifying the Archival Equipment and Materials also Explaining the Entry and Exit Mail for students in grade X of Office Administration program membership SMK PGRI 6 Malang. This study used a model of development ASSURE combined, and it is modified with 4D developmental model thus obtained 7 stages of development. Based on the validation results of the experts of media and material, the experts of media showed the percentage of 100% and the experts of material showed the percentage of 96.87%that those numbers showed that the instructional medium movie maker has very valid criteria. The results of the validation by a small group of students showed a percentage of 82% was obtained from the results of the empirical score divided by the maximum score. The results of the validation by a large group of students showed a percentage of 81.7% was obtained from the results of the empirical score divided by the maximum score. Abstrak: Tujuan penelitian ini untuk menghasilkan produk media pembelajaran movie maker dalam  kompetensi dasar Mengidentifikasi Alat dan Bahan Kearsipan serta Menjelaskan Pengurusan Surat Masuk dan Keluar untuk siswa kelas X program keahlian Administrasi Perkantoran SMK PGRI 6 Malang. Penelitian ini menggunakan model pengembangan ASSURE yang digabungkan dan dimodifikasi dengan model pengembangan 4D sehingga di peroleh 7 tahap pengembangan.  Berdasarkan hasil validasi ahli media dan ahli materi, dimana ahli media menunjukkan bahwa persentase sebesar 100% dan ahli materi menunjukkan bahwa persentase sebesar 96,87% dimana jumlah tersebut menunjukkan bahwa media pembelajaran movie maker memiliki kriteria sangat valid. Hasil validasi oleh siswa kelompok kecil menunjukkan persentase sebesar 82% di peroleh dari hasil skor empirik dibagi skor maksimal. Hasil validasi oleh siswa kelompok besar menunjukkan persentase sebesar 81

Tantalum X-ray contrast media, by M.G. Zuev and L.P. Larionov (Ekaterinburg: UrO RAN, 2002. 155 p.)

International Nuclear Information System (INIS)

Zhuravleva, E.Yu.

2004-01-01

The monograph of M.G. Zuev and L.P. Larionov Tantalum X-ray contrast media (Solid state chemistry for medicine series) is discussed. The monograph includes information on physical and chemical properties of tantalum, rare earths, and their oxides, phase compositions and phase diagrams of M 2 O 3 -Ta 2 O 5 (M - rare earths) systems is performed. Data on preclinical tests of yttrium orthotantalate and lanthanum orthotantalate as X-ray contrast media are given. Procedures for the production of X-ray contrast media involving tantalum oxide, rare earth tantalate and tantalum powder are described [ru

An Optimization Method of Time Window Based on Travel Time and Reliability

Directory of Open Access Journals (Sweden)

Fengjie Fu

2015-01-01

Full Text Available The dynamic change of urban road travel time was analyzed using video image detector data, and it showed cyclic variation, so the signal cycle length at the upstream intersection was conducted as the basic unit of time window; there was some evidence of bimodality in the actual travel time distributions; therefore, the fitting parameters of the travel time bimodal distribution were estimated using the EM algorithm. Then the weighted average value of the two means was indicated as the travel time estimation value, and the Modified Buffer Time Index (MBIT was expressed as travel time variability; based on the characteristics of travel time change and MBIT along with different time windows, the time window was optimized dynamically for minimum MBIT, requiring that the travel time change be lower than the threshold value and traffic incidents can be detected real time; finally, travel times on Shandong Road in Qingdao were estimated every 10 s, 120 s, optimal time windows, and 480 s and the comparisons demonstrated that travel time estimation in optimal time windows can exactly and steadily reflect the real-time traffic. It verifies the effectiveness of the optimization method.

A deep X-ray view of the bare AGN Ark 120. III. X-ray timing analysis and multiwavelength variability

Science.gov (United States)

Lobban, A. P.; Porquet, D.; Reeves, J. N.; Markowitz, A.; Nardini, E.; Grosso, N.

2018-03-01

We present the spectral/timing properties of the bare Seyfert galaxy Ark 120 through a deep ˜420 ks XMM-Newton campaign plus recent NuSTAR observations and a ˜6-month Swift monitoring campaign. We investigate the spectral decomposition through fractional rms, covariance and difference spectra, finding the mid- to long-time-scale (˜day-year) variability to be dominated by a relatively smooth, steep component, peaking in the soft X-ray band. Additionally, we find evidence for variable Fe K emission redward of the Fe Kα core on long time-scales, consistent with previous findings. We detect a clearly defined power spectrum which we model with a power law with a slope of α ˜ 1.9. By extending the power spectrum to lower frequencies through the inclusion of Swift and Rossi X-ray Timing Explorer data, we find tentative evidence of a high-frequency break, consistent with existing scaling relations. We also explore frequency-dependent Fourier time lags, detecting a negative (`soft') lag for the first time in this source with the 0.3-1 keV band lagging behind the 1-4 keV band with a time delay, τ, of ˜900 s. Finally, we analyse the variability in the optical and ultraviolet (UV) bands using the Optical/UV Monitor onboard XMM-Newton and the Ultra-Violet/Optical Telescope onboard Swift and search for time-dependent correlations between the optical/UV/X-ray bands. We find tentative evidence for the U-band emission lagging behind the X-rays with a time delay of τ = 2.4 ± 1.8 d, which we discuss in the context of disc reprocessing.

IMPROVING STUDENTS’ READING COMPREHENSION BY USING MEDIA AT THE GRADE X3 OF SMA NEGERI I TAMBANG-KAMPAR

Directory of Open Access Journals (Sweden)

Kurniawan Kurniawan

2017-07-01

Full Text Available At the grade X3 of SMAN I Tambang, the researcher found that the students havelow reading comprehension. One of the factors was the students’ lack of vocabulary. Theaimed of this research was to identify whether media can better improve students’ readingcomprehension and to find out what factors can influence the improvement of students’reading comprehension at the tenth grade students of SMAN 1 Tambang. This research wasClassroom Action Research (CAR. It had been carried out since May to June 2011. It hadtwo cycles and consisted of four meetings in each cycles. The participants of this researchwere the students at class X3 of SMAN I Tambang. They consisted of 39 students. Theresearcher found that media can better improve students’ reading comprehension at the gradeX3 of SMA Negeri I Tambang-Kampar. In conclusion, media can help the students toimprove their reading comprehension. The finding of this research implies that the use ofmedia can be used to enhance the students’ reading comprehension in English reading class.Key Words: Improve, Reading Comprehension, Media, Pictures, and Video

Representation of intangible cultural heritage of Bangladesh through social media

DEFF Research Database (Denmark)

Khalid, Md. Saifuddin; Chowdhury, Md Saiful Alam

2018-01-01

with approximately 160 million people is experiencing an exponential growth of social media users. Towards the goal of strategically representing and diffusing ICH through social media, this study explores the current roles of social media in the transmission of ICH in the virtual world through content analysis....... The potential roles of social media in the process of preserving ICH offer a space for building awareness, creating knowledge, and diffusion of innovations....

Inferior hilar window on lateral chest radiographs

International Nuclear Information System (INIS)

Park, C.K.; Webb, W.R.; Klein, J.S.

1990-01-01

This paper determines the accuracy of lateral chest radiography in the detection of masses in the inferior hilar window, a normally avascular hilar region anterior to the lower lobe bronchi. Fifty patients with normal thoracic CT scans and 25 with hilar masses/adenopathy were selected retrospectively. The 75 corresponding lateral chest radiographs were blindly evaluated for visibility of the anterior walls of the lower lobe bronchi and the presence and laterality of abnormal soft tissue (>1 cm) in the inferior hilar window. Only a 7 x 7-cm square of the lateral radiograph was viewed

Structural improvement of unliganded simian immunodeficiency virus gp120 core by normal-mode-based X-ray crystallographic refinement

International Nuclear Information System (INIS)

Chen, Xiaorui; Lu, Mingyang; Poon, Billy K.; Wang, Qinghua; Ma, Jianpeng

2009-01-01

The structural model of the unliganded and fully glycosylated simian immunodeficiency virus gp120 core determined to 4.0 Å resolution was substantially improved using a recently developed normal-mode-based anisotropic B-factor refinement method. The envelope protein gp120/gp41 of simian and human immunodeficiency viruses plays a critical role in viral entry into host cells. However, the extraordinarily high structural flexibility and heavy glycosylation of the protein have presented enormous difficulties in the pursuit of high-resolution structural investigation of some of its conformational states. An unliganded and fully glycosylated gp120 core structure was recently determined to 4.0 Å resolution. The rather low data-to-parameter ratio limited refinement efforts in the original structure determination. In this work, refinement of this gp120 core structure was carried out using a normal-mode-based refinement method that has been shown in previous studies to be effective in improving models of a supramolecular complex at 3.42 Å resolution and of a membrane protein at 3.2 Å resolution. By using only the first four nonzero lowest-frequency normal modes to construct the anisotropic thermal parameters, combined with manual adjustments and standard positional refinement using REFMAC5, the structural model of the gp120 core was significantly improved in many aspects, including substantial decreases in R factors, better fitting of several flexible regions in electron-density maps, the addition of five new sugar rings at four glycan chains and an excellent correlation of the B-factor distribution with known structural flexibility. These results further underscore the effectiveness of this normal-mode-based method in improving models of protein and nonprotein components in low-resolution X-ray structures

Investigation of water seepage through porous media using X-ray imaging technique

Science.gov (United States)

Jung, Sung Yong; Lim, Seungmin; Lee, Sang Joon

2012-07-01

SummaryDynamic movement of wetting front and variation of water contents through three different porous media were investigated using X-ray radiography. Water and natural sand particles were used as liquid and porous media in this study. To minimize the effects of minor X-ray attenuation and uneven illumination, the flat field correction (FFC) was applied before determining the position of wetting front. In addition, the thickness-averaged (in the direction of the X-ray penetration) water content was obtained by employing the Beer-Lambert law. The initial inertia of water droplet influences more strongly on the vertical migration, compared to the horizontal migration. The effect of initial inertia on the horizontal migration is enhanced as sand size decreases. The pattern of water transport is observed to be significantly affected by the initial water contents. As the initial water contents increases, the bulb-type transport pattern is shifted to a trapezoidal shape. With increasing surface temperature, water droplets are easily broken on the sand surface. This consequently decreases the length of the initial inertia region. Different from the wetting front migration, the water contents at the initial stage clearly exhibit a preferential flow along the vertical direction. The water transport becomes nearly uniform in all directions beyond the saturation state.

Environmental influences contributing to window failure of the SLAC 50 MW klystron

International Nuclear Information System (INIS)

Krienen, F.

1984-03-01

The additional heating of the klystron window is due to the intense x-ray level, produced inside the klystron, illuminating the entrance of the output wave guide. Photo-electric effect, although of low efficiency, produces enough electrons at the right location and right phase to start multipactor, which progresses with increasing intensity towards the window. The intercepted charge and the concomitant x-radiation heat the window, but the heating is not the cause of the breakdown per se. The accumulated charge on the window creates electric stress, which comes in addition to the RF stress. It could therefore be a major cause of electrical breakdown. The coating, which is intended to carry this charge off, should have a relaxation time constant small compared to the pulse duration. Unfortunately the coating can not be made conducting enough because it conflicts with the Joule heating in the RF field

Integral window/photon beam position monitor and beam flux detectors for x-ray beams

Science.gov (United States)

Shu, Deming; Kuzay, Tuncer M.

1995-01-01

A monitor/detector assembly in a synchrotron for either monitoring the position of a photon beam or detecting beam flux may additionally function as a vacuum barrier between the front end and downstream segment of the beamline in the synchrotron. A base flange of the monitor/detector assembly is formed of oxygen free copper with a central opening covered by a window foil that is fused thereon. The window foil is made of man-made materials, such as chemical vapor deposition diamond or cubic boron nitrate and in certain configurations includes a central opening through which the beams are transmitted. Sensors of low atomic number materials, such as aluminum or beryllium, are laid on the window foil. The configuration of the sensors on the window foil may be varied depending on the function to be performed. A contact plate of insulating material, such as aluminum oxide, is secured to the base flange and is thereby clamped against the sensor on the window foil. The sensor is coupled to external electronic signal processing devices via a gold or silver lead printed onto the contact plate and a copper post screw or alternatively via a copper screw and a copper spring that can be inserted through the contact plate and coupled to the sensors. In an alternate embodiment of the monitor/detector assembly, the sensors are sandwiched between the window foil of chemical vapor deposition diamond or cubic boron nitrate and a front foil made of similar material.

Teka-teki Unsur Kimia sebagai Media Pembelajaran Kimia Interaktif bagi siswa SMA Kelas X Berbasis Android

Directory of Open Access Journals (Sweden)

Isvandiari Fitri Utami

2016-01-01

Full Text Available Unsur kimia yang terdiri dari banyak unsur sering membuat siswa malas dengan mata pelajaran kimia khususnya dalam hal menghafal sistem periodik unsur kimia. Terkait dengan masalah ini, salah satu solusi yang ditawarkan adalah melalui media pembelajaran. Salah satu cara untuk membantu siswa melalui media pembelajaran dapat dilakukan dengan memanfaaatkan teknologi smartphone yang telah banyak dimiliki. Melihat banyaknya siswa yang telah menggunakan smartphone setiap harinya memungkinkan untuk memadukan kedua hal tersebut, sehingga siswa tidak hanya menggunakan smartphone sebagai sarana komunikasi, sosial media dan bermain game, tetapi dapat dialihkan menjadi sebuah inovasi positif dalam hal edukasi untuk menunjang sistem belajar yang interaktif. Tujuan dari penelitian ini adalah membuat aplikasi teka-teki unsur kimia sebagai media pembelajaran kimia interaktif bagi siswa SMA kelas X berbasis android. Salah satu manfaat dari penelitian ini adalah hasil penelitian dapat dijadikan rujukan bagi perkembangan dunia teknologi dan berguna juga untuk menjadi referensi bagi mahasiswa yang melakukan pengembangan produk teknologi khususnya mengenai media pembelajaran berbasis android. Dalam melakukan penelitian ini, aplikasi dibangun dengan menggunakan metode pengembangan multimedia development life cycle, data dan informasi mengenai unsur- unsur kimia dalam sistem periodik unsur diperoleh dari buku materi kimia SMA kelas X berdasarkan kurikulum 2006, beberapa jurnal, dan dari pengajar kimia untuk materi SMA kelas X secara langsung. Pada tahapan implementasi, program dibuat dengan drag and drop serta menggunakan bahasa pemrograman Javascript. Pengujian yang dilakukan pada aplikasi adalah dengan menggunakan metode whitebox. Berdasarkan hasil pengujian yang dilakukan pada aplikasi teka-teki unsur kimia sebagai media pembelajaran kimia interaktif berbasis aplikasi android, aplikasi sudah mampu berjalan cukup maksimal. Hasil pengujian mampu menampilkan

Windows Azure

CERN Document Server

Johnson, Bruce; Chambers, James; Garber, Danny; Malik, Jamal; Fazio, Adam

2013-01-01

A collection of five must-have Azure titles, from some of the biggest names in the field Available individually, but at a discounted rate for the collection, this bundle of five e-books covers key developer and IT topics of Windows Azure, including ASP.NET, mobile services, web sites, data storage, and the hybrid cloud. A host of Microsoft employees and MPVs come together to cover the biggest challenges that professionals face when working with Windows Azure. The e-books included are as follows: Windows Azure and ASP.NET MVC MigrationWindows Azure Mobile ServicesWindows Azure Web SitesWindows

Learning Windows Azure Mobile Services for Windows 8 and Windows Phone 8

CERN Document Server

Webber-Cross, Geoff

2014-01-01

This book is based around a case study game which was written for the book. This means that the chapters progress in a logical way and build upon lessons learned as we go. Real-world examples are provided for each topic that are practical and not given out-of-context so they can be applied directly to other applications.If you are a developer who wishes to build Windows 8 and Phone 8 applications and integrate them with Windows Azure Mobile Services, this book is for you. Basic C# and JavaScript skills are advantageous, as well as some knowledge of building Windows 8 or Windows Phone 8 applica

Corrosion of titanium alloys in concentrated chloride solutions at temperature up to 160 deg C

International Nuclear Information System (INIS)

Ruskol, Yu.S.; Viter, L.I.; Balakin, A.I.; Fokin, M.N.

1982-01-01

Resistance of VT1-0 titanium and 4200, 4207 titanium alloys to pitting and total corrosion in chlorides of cadmium, potassium, nickel, ammonium, barium, calcium, lithium, magnesium in respect to pH value and temperature (120,140,160 deg C) is determined. The results obtained are presented as nomograms of stability. Possible reasons for corrosion behaviour of titanium in each of the chlorides are discussed

Preliminary Results of Reductive Dechlorination Conducted at the X-749/X-120 Area of the DOE Portsmouth Gaseous Diffusion Plant, Piketon, Ohio

International Nuclear Information System (INIS)

Rieske, D. E.; Baird, D. R.; Lawson, N. E.

2006-01-01

Reductive dechlorination is being implemented at the X-749/X-120 trichloroethene (TCE) plume South Barrier Wall containment site at the Department of Energy (DOE) Portsmouth Gaseous Diffusion Plant (PORTS). The purpose of this paper is to present the effectiveness of the reductive dechlorination at PORTS. Reductive dechlorination is an in situ remediation technology that utilizes existing subsurface microbes to biologically degrade volatile organic compounds in groundwater. Monitoring in the barrier wall area reveals the presence of Hydrogen Release Compound (HRC) injected in the spring of 2004 in two groundwater monitoring wells closest to the injection points. Oxidation/reduction potential in these two wells has decreased steadily since injection, but has not yet reached optimal reducing levels for TCE degradation. Monitoring the effectiveness of the injection is hampered by near-stagnant groundwater flow due in part to the South Barrier Wall. The X-749/X-120 TCE groundwater plume lies beneath approximately 91 acres in the southern portion of PORTS, and extends southward threatening to cross the DOE property boundary. A 1,077-foot long subsurface bentonite barrier wall was installed in 1993 at the southern DOE property boundary to restrict movement of contaminated groundwater from traveling off-site until other remedial technologies could be implemented. In 2003, TCE was detected on the south side of the barrier wall (but still within DOE property) above drinking water standards of 5 micrograms per liter. Monitoring has also detected TCE in groundwater beyond the western edge of the barrier wall. In the spring of 2004, DOE initiated the injection of a reductive dechlorination compound known as Hydrogen Release Compound-extended release formula (HRC-X) into the subsurface using direct push technology (DPT). The HRC-X was injected within the saturated zone from the top of bedrock to 10 feet above bedrock as the probe was withdrawn from the push. A total of 180 DPT

A sealable ultrathin window sample cell for the study of liquids by means of soft X-ray spectroscopy

Science.gov (United States)

Grötzsch, D.; Streeck, C.; Nietzold, C.; Malzer, W.; Mantouvalou, I.; Nutsch, A.; Dietrich, P.; Unger, W.; Beckhoff, B.; Kanngießer, B.

2017-12-01

A new sample cell concept for the analysis of liquids or solid-liquid interfaces using soft X-ray spectroscopy is presented, which enables the complete sealing of the cell as well as the transport into vacuum via, for example, a load-lock system. The cell uses pressure monitoring and active as well as passive pressure regulation systems, thereby facilitating the full control over the pressure during filling, sealing, evacuation, and measurement. The cell design and sample preparation as well as the crucial sealing procedure are explained in detail. As a first proof-of-principle experiment, successful nitrogen K-edge fluorescence yield near-edge X-ray absorption fine structure experiments of a biomolecular solution are presented. For this purpose, it is shown that the careful evaluation of all involved parameters, such as window type or photon flux, is desirable for optimizing the experimental result.

Radiographic contrast media

International Nuclear Information System (INIS)

Golman, K.; Holtz, E.; Almen, T.

1987-01-01

Contrast media are used in diagnostic radiology to enhance the X-ray attenuation between a body structure of interest and the surrounding tissue. A detail becomes perceptible on a roentgenogram only when its contrast exceeds a minimum value in relation to the background. Small areas of interest must have higher contrast than the background. The contrast effect depends on concentration of the contrast media with the body. A high contrast media concentration difference thus gives rise to more morphological details in the radiographs. Contrast media can be divided into negative contrast media such as air and gas which attenuate X-rays less than the body tissues, and positive contrast materials which attenuate X-rays more than the body tissues. The positive contrast media all contain either iodine (atomic number 53) or barium (atomic number 56) and can be divided into water-insoluble and water-soluble contrast media

X Python reference manual

NARCIS (Netherlands)

K.S. Mullender (Sjoerd)

1995-01-01

textabstractThis document describes the built-in types, exceptions, and functions of the X windows extension to Python. It assumes basic knowledge about the Python language and access to the X windows documentation. For an informal introduction to the language, see the Python Tutorial. The Python

Delayed allergy-like reactions to X-ray contrast media. Second expert meeting

International Nuclear Information System (INIS)

Sviridov, N.K

1998-01-01

Materials of the second expert meeting of medical radiologists of USA, Germany, and Japan concerning delayed allergy-like reactions to X-ray contrast media (XRCM) are briefly considered. Attention is paid to the experimental and clinical data on the application of nonionic dimers, pathophysiological and immunological aspects of the reaction to XRCM, certain models and hypotheses, allergy to XRCM

Collimator and energy window optimization for 90Y bremsstrahlung SPECT imaging: A SIMIND Monte Carlo study

International Nuclear Information System (INIS)

Roshan, Hoda Rezaei; Mahmoudian, Babak; Gharepapagh, Esmaeil; Azarm, Ahmadreza; Pirayesh Islamian, Jalil

2016-01-01

Treatment efficacy of radioembolization using Yttrium-90 ( 90 Y) microspheres is assessed by the 90 Y bremsstrahlung single photon emission computed tomography (SPECT) imaging following radioembolization. The radioisotopic image has the potential of providing reliable activity map of 90 Y microspheres distribution. One of the main reasons of the poor image quality in 90 Y bremsstrahlung SPECT imaging is the continuous and broad energy spectrum of the related bremsstrahlung photons. Furthermore, collimator geometry plays an impressive role in the spatial resolution, sensitivity and image contrast. Due to the relatively poor quality of the 90 Y bremsstrahlung SPECT images, we intend to optimize the medium-energy (ME) parallel-hole collimator and energy window. The Siemens e.cam gamma camera equipped with a ME collimator and a voxelized phantom was simulated by the SImulating Medical Imaging Nuclear Detectors (SIMIND) program. We used the SIMIND Monte Carlo program to generate the 90 Y bremsstrahlung SPECT projection of the digital Jaszczak phantom. The phantom consist of the six hot spheres ranging from 9.5 to 31.8 mm in diameter, which are used to evaluate the image contrast. In order to assess the effect of the energy window on the image contrast, three energy windows ranging from 60 to 160 KeV, 160 to 400 KeV, and 60 to 400 KeV were set on a 90 Y bremsstrahlung spectrum. As well, the effect of the hole diameter of a ME collimator on the image contrast and bremsstrahlung spectrum were investigated. For the fixed collimator and septa thickness values (3.28 cm and 1.14 mm, respectively), a hole diameter range (2.35–3.3 mm) was chosen based on the appropriate balance between the spatial resolution and sensitivity. The optimal energy window for 90 Y bremsstrahlung SPECT imaging was extended energy window from 60 to 400 KeV. Besides, The optimal value of the hole diameter of ME collimator was obtained 3.3 mm. Geometry of the ME parallel-hole collimator and energy

Windows server cookbook for Windows server 2003 and Windows 2000

CERN Document Server

Allen, Robbie

2005-01-01

This practical reference guide offers hundreds of useful tasks for managing Windows 2000 and Windows Server 2003, Microsoft's latest server. These concise, on-the-job solutions to common problems are certain to save you many hours of time searching through Microsoft documentation. Topics include files, event logs, security, DHCP, DNS, backup/restore, and more

Delayed allergy-like reactions to X-ray contrast media administration focusing on clinical aspects. First expert meeting

International Nuclear Information System (INIS)

Sviridov, N.K.

1998-01-01

Materials presented at the first expert meeting of leading specialists in medical radiology are briefly described. The include 14 reports of the scientists of Germany, England, Japan, USA, Finland, Austria. The reports concert delayed allergy-like response to X-ray contrast media accepting on clinical aspects and analysis of nonionic dimeric isotonic media application

Portable pulse X-ray micro and nanosecond range apparatus for studying fast-going processes in opaque media

International Nuclear Information System (INIS)

Goganov, D.A.; Komyak, N.I.; Pelix, E.A.

Pulse X-radiography (X-ray flash duration in the order of 10 -6 -10 -9 sec) is the principal method for studying fast-going processes in opaque media by serial and parallel radiographic imaging. Description is given and main features are outlined of pulse X-ray apparatus IRA-4b, 5b, 6b producing X-radiation flashes from 0.3 μsec to 10-20 nsec in duration

T25 ITER ECH window development 110 GHz ECH distributed window development. Final report, May 1, 1994 - December 31, 1995

International Nuclear Information System (INIS)

Olstad, R.A.; Moeller, C.P.; Grunloh, H.J.

1998-01-01

Electron Cyclotron Heating (ECH) is one of the major candidates for Heating and Current Drive on ITER. ECH is extremely attractive from a reactor engineering point of view, offering compact launch structures, high injected power density, and a simple interface with the shield/blanket. Economic deployment of ECH for ITER requires MW unit microwave sources (gyrotrons). The present technology limitation is the availability of suitable low loss output windows. These are needed for the torus as well as the tube. The torus window, in particular, is a demanding application as it also serves as a tritium barrier. Several distinct window concepts are under development by the various Parties. This report summarizes the efforts to make and test a open-quotes distributedclose quotes window suitable for 1 MW cw operation at 110 GHz. A companion report (Final Report on Task 245+) describes the efforts to make a distributed window suitable for 1 MW cw operation at 170 GHz, the main frequency of interest to ITER. General Atomics (GA) fabricated a 4 in. x 4 in. 110 GHz distributed window which was delivered in September 1995 to Communications and Power Industries (CPI). Hot tests at CPI confirmed the power handling capability of the window. Tests were conducted with a reduced beam size at 200 kW with 0.7 s pulses without any arcing or excessive window temperatures. The power density and pulse length were equivalent to that in a full size 1.2 MW CW beam with a peak-to-average power ratio of 2.7. This window was assembled using a gold braze material to bond the sapphire strips to the niobium frame. The braze was successful except for small leaks at two locations, and re-braze efforts were unsuccessful

A single-channel 10-bit 160 MS/s SAR ADC in 65 nm CMOS

International Nuclear Information System (INIS)

Lu Yuxiao; Sun Lu; Li Zhe; Zhou Jianjun

2014-01-01

This paper demonstrates a single-channel 10-bit 160 MS/s successive-approximation-register (SAR) analog-to-digital converter (ADC) in 65 nm CMOS process with a 1.2 V supply voltage. To achieve high speed, a new window-opening logic based on the asynchronous SAR algorithm is proposed to minimize the logic delay, and a partial set-and-down DAC with binary redundancy bits is presented to reduce the dynamic comparator offset and accelerate the DAC settling. Besides, a new bootstrapped switch with a pre-charge phase is adopted in the track and hold circuits to increase speed and reduce area. The presented ADC achieves 52.9 dB signal-to-noise distortion ratio and 65 dB spurious-free dynamic range measured with a 30 MHz input signal at 160 MHz clock. The power consumption is 9.5 mW and a core die area of 250 × 200 μm 2 is occupied. (semiconductor integrated circuits)

Development of L-band pillbox RF window

International Nuclear Information System (INIS)

Takeuchi, Y.; Fukuda, S.; Hisamatsu, H.; Saito, Y.; Takahashi, A.

1994-01-01

A pillbox RF output window was developed for the L-band pulsed klystron for the Japanese Hadron Project (JHP) 1-GeV proton linac. The window was designed to withstand a peak RF power of 6 MW, where the pulse width is 600 μsec and the repetition rate is 50 Hz. A high power model was fabricated using an alumina ceramic which has a low loss tangent of 2.5x10 -5 . A high power test was successfully performed up to a 113 kW RF average power with a 4 MW peak power, a 565 μsec pulse width and a 50 Hz repetition rate. By extrapolating the data of this high power test, the temperature rise of the ceramic is estimated low enough at the full RF power of 6 MW. Thus this RF window is expected to satisfy the specifications of the L-band Klystron. (author)

MS Windows domēna darbstaciju migrācija no MS Windows XP uz Windows Vista.

OpenAIRE

Tetere, Agate

2009-01-01

Kvalifikācijas darbā izpētīju darbstaciju migrācijas no Windows XP uz Windows Vista plusus un mīnusus. Darba gaitā tika veikti sekojoši uzdevumi: 1.Veikta Windows XP un Windows Vista darbstaciju instalācija, iestatījumu konfigurēšana un tika pārbaudīta sistēmas darbība 2.Veikta Windows Server 2003 un Windows Server 2008 instalācija, iestatījumu konfigurēšana un tika pārbaudīta sistēmas darbība 3.Izstrādāts migrācijas modelis 4.Veikta migrācijas optimizēšana 5.Veikta datu migrāc...

Application of xCELLigence RTCA Biosensor Technology for Revealing the Profile and Window of Drug Responsiveness in Real Time

Directory of Open Access Journals (Sweden)

Dan Kho

2015-04-01

Full Text Available The xCELLigence technology is a real-time cellular biosensor, which measures the net adhesion of cells to high-density gold electrode arrays printed on custom-designed E-plates. The strength of cellular adhesion is influenced by a myriad of factors that include cell type, cell viability, growth, migration, spreading and proliferation. We therefore hypothesised that xCELLigence biosensor technology would provide a valuable platform for the measurement of drug responses in a multitude of different experimental, clinical or pharmacological contexts. In this manuscript, we demonstrate how xCELLigence technology has been invaluable in the identification of (1 not only if cells respond to a particular drug, but (2 the window of drug responsiveness. The latter aspect is often left to educated guess work in classical end-point assays, whereas biosensor technology reveals the temporal profile of the response in real time, which enables both acute responses and longer term responses to be profiled within the same assay. In our experience, the xCELLigence biosensor technology is suitable for highly targeted drug assessment and also low to medium throughput drug screening, which produces high content temporal data in real time.

Usage of CO2 microbubbles as flow-tracing contrast media in X-ray dynamic imaging of blood flows.

Science.gov (United States)

Lee, Sang Joon; Park, Han Wook; Jung, Sung Yong

2014-09-01

X-ray imaging techniques have been employed to visualize various biofluid flow phenomena in a non-destructive manner. X-ray particle image velocimetry (PIV) was developed to measure velocity fields of blood flows to obtain hemodynamic information. A time-resolved X-ray PIV technique that is capable of measuring the velocity fields of blood flows under real physiological conditions was recently developed. However, technical limitations still remained in the measurement of blood flows with high image contrast and sufficient biocapability. In this study, CO2 microbubbles as flow-tracing contrast media for X-ray PIV measurements of biofluid flows was developed. Human serum albumin and CO2 gas were mechanically agitated to fabricate CO2 microbubbles. The optimal fabricating conditions of CO2 microbubbles were found by comparing the size and amount of microbubbles fabricated under various operating conditions. The average size and quantity of CO2 microbubbles were measured by using a synchrotron X-ray imaging technique with a high spatial resolution. The quantity and size of the fabricated microbubbles decrease with increasing speed and operation time of the mechanical agitation. The feasibility of CO2 microbubbles as a flow-tracing contrast media was checked for a 40% hematocrit blood flow. Particle images of the blood flow were consecutively captured by the time-resolved X-ray PIV system to obtain velocity field information of the flow. The experimental results were compared with a theoretically amassed velocity profile. Results show that the CO2 microbubbles can be used as effective flow-tracing contrast media in X-ray PIV experiments.

Grab Windows training opportunities; check CERN Windows roadmap!

CERN Multimedia

IT Department

2011-01-01

CERN Operating Systems and Information Services group (IT-OIS) actively monitors market trends to check how new software products correspond to CERN needs. In the Windows world, Windows 7 has been a big hit, with over 1500 Windows 7 PCs within less than a year since its support was introduced at CERN. No wonder: Windows XP is nearly 10 years old and is steadily approaching the end of its life-cycle. At CERN, support for Windows XP will stop at the end of December 2012. Compared to Vista, Windows 7 has the same basic hardware requirements, but offers higher performance, so the decision to upgrade is rather straightforward. CERN support for Vista will end in June 2011. In the world of Microsoft Office, version 2007 offers better integration with the central services than the older version 2003. Progressive upgrade from 2003 to 2007 is planned to finish in September 2011, but users are encouraged to pro-actively upgrade at their convenience. Please note that Office 2007 brings an important change in the area of ...

The Dynamic Cross-Correlations between Mass Media News, New Media News, and Stock Returns

Directory of Open Access Journals (Sweden)

Zuochao Zhang

2018-01-01

Full Text Available We investigate the dynamic cross-correlations between mass media news, new media news, and stock returns for the SSE 50 Index in Chinese stock market by employing the MF-DCCA method. The empirical results show that (1 there exist power-law cross-correlations between two types of news as well as between news and its corresponding SSE 50 Index return; (2 the cross-correlations between mass media news and SSE 50 Index returns show larger multifractality and more complicated structures; (3 mass media news and new media news have both complementary and competitive relationships; (4 with the rolling window analysis, we further find that there is a general increasing trend for the cross-correlations between the two types of news as well as the cross-correlations between news and returns and this trend becomes more persistent over time.

High Reflectance Nanoscale V/Sc Multilayer for Soft X-ray Water Window Region.

Science.gov (United States)

Huang, Qiushi; Yi, Qiang; Cao, Zhaodong; Qi, Runze; Loch, Rolf A; Jonnard, Philippe; Wu, Meiyi; Giglia, Angelo; Li, Wenbin; Louis, Eric; Bijkerk, Fred; Zhang, Zhong; Wang, Zhanshan

2017-10-10

V/Sc multilayer is experimentally demonstrated for the first time as a high reflectance mirror for the soft X-ray water window region. It primarily works at above the Sc-L edge (λ = 3.11 nm) under near normal incidence while a second peak appears at above the V-L edge (λ = 2.42 nm) under grazing incidence. The V/Sc multilayer fabricated with a d-spacing of 1.59 nm and 30 bilayers has a smaller interface width (σ = 0.27 and 0.32 nm) than the conventional used Cr/Sc (σ = 0.28 and 0.47 nm). For V/Sc multilayer with 30 bilayers, the introduction of B 4 C barrier layers has little improvement on the interface structure. As the number of bilayers increasing to 400, the growth morphology and microstructure of the V/Sc layers evolves with slightly increased crystallization. Nevertheless, the surface roughness remains to be 0.25 nm. A maximum soft X-ray reflectance of 18.4% is measured at λ = 3.129 nm at 9° off-normal incidence using the 400-bilayers V/Sc multilayer. According to the fitted model, an s-polarization reflectance of 5.2% can also be expected at λ = 2.425 nm under 40° incidence. Based on the promising experimental results, further improvement of the reflectance can be achieved by using a more stable deposition system, exploring different interface engineering methods and so on.

Anomalous signature splitting of the πh11/2direct x νi13/2 band in A-160 odd-odd nuclei

International Nuclear Information System (INIS)

Yang Chunxiang; Zhou Hongyu

2003-01-01

Systematic features of anomalous signature splitting of the πh 11/2 direct x νi 13/2 band in A-160 odd-odd nuclei have been investigated. It is shown that the mechanism of anomalous signature splitting is similar to that of the normal signature splitting which is essentially caused by the Coriolis mixing of Ω=1/2 components into the nuclear wavefunction and the anomalous splitting in signature is mainly caused by the definition. The extensively observed anomalous signature splitting in this band might be an indication that the interaction between the h 11/2 proton and the i 13/2 neutron cannot be neglected. The new observation of high- and low-K bands based on the same πh 11/2 direct x νi 13/2 configuration in 164 Tm is also discussed

Temporal behavior of unresolved transition array emission in water window soft x-ray spectral region from multiply charged ions

Energy Technology Data Exchange (ETDEWEB)

Dinh, Thanh-Hung, E-mail: dinh@cc.utsunomiya-u.ac.jp; Suzuki, Yuhei; Arai, Goki; Higashiguchi, Takeshi, E-mail: higashi@cc.utsunomiya-u.ac.jp [Department of Electrical and Electronic Engineering, Faculty of Engineering and Center for Optical Research and Education (CORE), Utsunomiya University, Yoto 7-1-2, Utsunomiya, Tochigi 321-8585 (Japan); Li, Bowen [School of Nuclear Science and Technology, Lanzhou University, Lanzhou 730000 (China); Dunne, Padraig; O' Sullivan, Gerry [School of Physics, University College Dublin, Belfield, Dublin 4 (Ireland); Fujioka, Shinsuke [Institute of Laser Engineering, Osaka University, 2-6 Yamada-oka, Suita, Osaka 565-0871 (Japan); Hasegawa, Noboru; Kawachi, Tetsuya; Nishikino, Masaharu [Quantum Beam Science Center, Japan Atomic Energy Agency, 8-1-7 Umemidai, Kizugawa, Kyoto 619-0215 (Japan)

2015-09-21

We have characterized the spectral structure and the temporal history of the laser-produced high-Z multi-charged ion plasmas for the efficient water window soft x-ray sources. Strong unresolved transition array emission was observed due to 4d–4f and 4f–5g transitions from Au, Pb, and Bi plasmas in the 280–700 eV photon energy region. The temporal behavior of the emission was essentially similar of that of the laser pulse with a slight delay between different transitions. These results provide feedback for accurate modeling of the atomic processes with the radiative hydrodynamic simulations.

Music expertise shapes audiovisual temporal integration windows for speech, sinewave speech and music

Directory of Open Access Journals (Sweden)

Hwee Ling eLee

2014-08-01

Full Text Available This psychophysics study used musicians as a model to investigate whether musical expertise shapes the temporal integration window for audiovisual speech, sinewave speech or music. Musicians and non-musicians judged the audiovisual synchrony of speech, sinewave analogues of speech, and music stimuli at 13 audiovisual stimulus onset asynchronies (±360, ±300 ±240, ±180, ±120, ±60, and 0 ms. Further, we manipulated the duration of the stimuli by presenting sentences/melodies or syllables/tones. Critically, musicians relative to non-musicians exhibited significantly narrower temporal integration windows for both music and sinewave speech. Further, the temporal integration window for music decreased with the amount of music practice, but not with age of acquisition. In other words, the more musicians practiced piano in the past three years, the more sensitive they became to the temporal misalignment of visual and auditory signals. Collectively, our findings demonstrate that music practicing fine-tunes the audiovisual temporal integration window to various extents depending on the stimulus class. While the effect of piano practicing was most pronounced for music, it also generalized to other stimulus classes such as sinewave speech and to a marginally significant degree to natural speech.

Experimental investigations on the weakening of pulsed X-radiation by contrast media

Energy Technology Data Exchange (ETDEWEB)

Moldenhauer, K

1973-07-25

In order to be able to carry out a videodensitometry simultaneously with the cineangiocardiography with pulsed X-rays, the weakening of the X-radiation by contrast media is more closely examined and a calibration of the amplitudes is carried out. The determination of the extinction curves for different parts of the X-ray pulses show that under unfavourable conditions (high voltage, low tube current, no Cu filtration) the spectrum is displaced to larger wavelengths, white an influence on the weakness coefficient only occurs after the intensity has fallen to 10% of the impulse maximum. On the other hand, the quantity depedence of the extinction coefficient is significant. The densitometry simulations performed with a digital computer using empirically gained calibration curves show that a quantitative densitometry is possible even if the Lambert-Beer law is not valid.

Experimental investigations on the weakening of pulsed X-radiation by contrast media

International Nuclear Information System (INIS)

Moldenhauer, K.

1973-01-01

In order to be able to carry out a videodensitometry simultaneously with the cineangiocardiography with pulsed X-rays, the weakening of the X-radiation by contrast media is more closely examined and a calibration of the amplitudes is carried out. The determination of the extinction curves for different parts of the X-ray pulses show that under unfavourable conditions (high voltage, low tube current, no Cu filtration) the spectrum is displaced to larger wavelengths, white an influence on the weakness coefficient only occurs after the intensity has fallen to 10% of the impulse maximum. On the other hand, the quantity depedence of the extinction coefficient is significant. The densitometry simulations performed with a digital computer using empirically gained calibration curves show that a quantitative densitometry is possible even if the Lambert-Beer law is not valid. (ORU/LH) [de

Flexible power 90W to 120W ArF immersion light source for future semiconductor lithography

Science.gov (United States)

Burdt, R.; Thornes, J.; Duffey, T.; Bibby, T.; Rokitski, R.; Mason, E.; Melchior, J.; Aggarwal, T.; Haran, D.; Wang, J.; Rechtsteiner, G.; Haviland, M.; Brown, D.

2014-03-01

Semiconductor market demand for improved performance at lower cost continues to drive enhancements in excimer light source technologies. Increased output power, reduced variability in key light source parameters, and improved beam stability are required of the light source to support immersion lithography, multi-patterning, and 450mm wafer applications in high volume semiconductor manufacturing. To support future scanner needs, Cymer conducted a technology demonstration program to evaluate the design elements for a 120W ArFi light source. The program was based on the 90W XLR 600ix platform, and included rapid power switching between 90W and 120W modes to potentially support lot-to-lot changes in desired power. The 120W requirements also included improved beam stability in an exposure window conditionally reduced by 20%. The 120W output power is achieved by efficiency gains in system design, keeping system input power at the same level as the 90W XLR 600ix. To assess system to system variability, detailed system testing was conducted from 90W - 120W with reproducible results.

Window Stories

DEFF Research Database (Denmark)

Hauge, Bettina

This research project has investigated 17 households in Germany (cities and rural areas). The main aim was to learn about the significance of the window to these people: What they think of their windows, how, when and why they use them in their everyday life, if they have a favorite window and wh...

Windows 10 simplified

CERN Document Server

McFedries, Paul

2015-01-01

Learn Windows 10 quickly and painlessly with this beginner's guide Windows 10 Simplified is your absolute beginner's guide to the ins and outs of Windows. Fully updated to cover Windows 10, this highly visual guide covers all the new features in addition to the basics, giving you a one-stop resource for complete Windows 10 mastery. Every page features step-by-step screen shots and plain-English instructions that walk you through everything you need to know, no matter how new you are to Windows. You'll master the basics as you learn how to navigate the user interface, work with files, create

Windows and doors

Energy Technology Data Exchange (ETDEWEB)

1988-01-01

A complete manual is presented on windows and doors for the housing contractor. In order to understand the role of windows and doors in a house's energy performance, an introduction explains the house as a system of components that can have effects on each other. Further chapters explain in detail the parts of a window, window types and RSI values; window servicing and repair; window replacement; parts of a door, door types and RSI values; door service and repair, including weatherstripping; door replacement; and how to ensure quality, service, and customer satisfaction. A glossary of terms is included. 61 figs., 3 tabs.

Interactive floating windows: a new technique for stereoscopic video games

Science.gov (United States)

Zerebecki, Chris; Stanfield, Brodie; Tawadrous, Mina; Buckstein, Daniel; Hogue, Andrew; Kapralos, Bill

2012-03-01

The film industry has a long history of creating compelling experiences in stereoscopic 3D. Recently, the video game as an artistic medium has matured into an effective way to tell engaging and immersive stories. Given the current push to bring stereoscopic 3D technology into the consumer market there is considerable interest to develop stereoscopic 3D video games. Game developers have largely ignored the need to design their games specifically for stereoscopic 3D and have thus relied on automatic conversion and driver technology. Game developers need to evaluate solutions used in other media, such as film, to correct perceptual problems such as window violations, and modify or create new solutions to work within an interactive framework. In this paper we extend the dynamic floating window technique into the interactive domain enabling the player to position a virtual window in space. Interactively changing the position, size, and the 3D rotation of the virtual window, objects can be made to 'break the mask' dramatically enhancing the stereoscopic effect. By demonstrating that solutions from the film industry can be extended into the interactive space, it is our hope that this initiates further discussion in the game development community to strengthen their story-telling mechanisms in stereoscopic 3D games.

MEDIA PEMBELAJARAN PERSAMAAN KUADRAT DAN FUNGSI KUADRAT MATA PELAJARAN MATEMATIKA KELAS X

Directory of Open Access Journals (Sweden)

Sasono Wibowo

2012-02-01

Full Text Available Proses belajar mengajar khususnya dalam mata pelajaran matematika bagi sebagian besar siswa sangatlah suatu yang membosankan, untuk itu harus ada cara atau media yang bisa membuat para siswa tertarik dan nyaman untuk mempelajarinya. Pembuatan media pembelajaran persamaan kuadrat dan fungsi kuadrat pada mata pelajaran matematika untuk kelas X Semester Gasal dengan menggunakan Macromedia Flash 8" Tujuan dari tulisan ini adalah untuk memungkinkan siswa lebih mudah belajar dan memahami pelajaran matematika khususnya dalam hal persamaan kuadrat dan fungsi kuadrat. Program bantu sistem belajar dengan menggunakan model Waterfall metode desain dan sistem analisis rekayasa perangkat lunak analisis persyaratan, desain, menulis program, pengujian dan pemeliharaan. program bantuan untuk menambah pengetahuan tentang penyelesaian persamaan kuadrat dan fungsi kuadrat adalah dalam bentuk informasi cara perhitungan dan beberapa soal latihan. Kata kunci : belajar, persamaan kuadrat, fungsi kuadrat.

Beryllium parabolic refractive x-ray lenses

International Nuclear Information System (INIS)

Lengeler, B.; Schroer, C.G.; Kuhlmann, M.; Benner, B.; Guenzler, T.F.; Kurapova, O.; Somogyi, A.; Snigirev, A.; Snigireva, I.

2004-01-01

Parabolic refractive x-ray lenses are novel optical components for the hard x-ray range from about 5 keV to about 120 keV. They focus in both directions. They are compact, robust, and easy to align and to operate. They can be used like glass lenses are used for visible light, the main difference being that the numerical aperture N.A. is much smaller than 1 (of order 10-4 to 10-3). Their main applications are in micro- and nanofocusing, in imaging by absorption and phase contrast and in fluorescence mode. In combination with tomography they allow for 3-dimensional imaging of opaque media with submicrometer resolution. Finally, they can be used in speckle spectroscopy by means of coherent x-ray scattering. Beryllium as lens material strongly enhances the transmission and the field of view as compared to aluminium. With increased N.A. the lateral resolution is also considerably improved with Be lenses. References to a number of applications are given

Development of cattleya amethystoglossa x nobilior - orquidaceae in simplified culture media

Directory of Open Access Journals (Sweden)

Murilo Goulart Berka

2014-08-01

Full Text Available Three simplified, low-cost culture media, prepared with foliar fertilizers, were compared with the commonly used ½ MS-ban (Murashige Skoog medium ½ salt concentration, with banana fruit for the in vitro multiplication of the orchid hybrid Cattleya amethystoglossa x nobilior. The simplified culture media tested were Hy-ban, which is made with 1.33 g L-1 of Hyponex fertilizer (NPK 6.5-6-19; KP-ban, which is made with 0.92 g L-1 of Kristalon™ (NPK 6-12-36 and 0.26 g L-1 of Peters (NPK 30-10-10; and Kcal-ban, which is made with 0.92 g L-1 of Kristalon™ (NPK 6-12-36 and 0.51 g L-1 of Calcinit (NPK 15.5-0-0+Ca 19.0%. Each medium was supplemented with 20 g L-1 of sucrose, 1 g L-1 of activated charcoal, 7 g L-1 of agar-agar and 40 g L-1 of banana fruit, pH 5.6. Plantlets were evaluated after 80 days for the following parameters: number of shoots, shoot length, number of roots, longest root length and fresh weight. While all four media can be used for the studied hybrid, the best medium was Kcal-ban.

MS Windows domēna darbstacijas migrācijas iespējas no MS Windows XP uz MS Windows 7.

OpenAIRE

Zariņš, Valdis

2009-01-01

Kvalifikācijas darbā tiek aprakstītas MS Windows domēna darbstacijas migrācijas iespējas no MS Windows XP uz MS Windows 7, kā servera operētājsistēmas izmantojot tādus Microsoft produktus, kā Microsoft Windows Server 2003 un Microsoft Windows Server 2008. Kvalifikācijas darba teorētiskaja daļā tiek apskatīti Microsoft Windows 7 priekšrocības un uzlabojumus gan no darbstacijas lietotāja , gan no darbstacijas administratora puses. Ir aprakstītas Microsoft Windows Server 2008 jauninājumu ie...

MULTIWAVELENGTH VARIABILITY OF THE BROAD LINE RADIO GALAXY 3C 120

International Nuclear Information System (INIS)

Marshall, Kevin; Ryle, Wesley T.; Miller, H. Richard; Marscher, Alan P.; Jorstad, Svetlana G.; Chicka, Benjamin; McHardy, Ian M.

2009-01-01

We present results from a multiyear monitoring campaign of the broad-line radio galaxy 3C 120, using the Rossi X-ray Timing Explorer for nearly five years of observations. Additionally, we present coincident optical monitoring using data from several ground-based observatories. Both the X-ray and optical emission are highly variable and appear to be strongly correlated, with the X-ray emission leading the optical by 28 days. The X-ray power density spectrum is best fit by a broken power law, with a low-frequency slope of -1.2, breaking to a high-frequency slope of -2.1, and a break frequency of log ν b = -5.75 Hz, or 6.5 days. This value agrees well with the value expected based on 3C 120's mass and accretion rate. We find no evidence for a second break in the power spectrum. Combined with a moderately soft X-ray spectrum (Γ = 1.8) and a moderately high accretion rate, this indicates that 3C 120 fits in well with the high/soft variability state found in most other active galactic nuclei. Previous studies have shown that the spectrum has a strong Fe Kα line, which may be relativistically broadened. The presence of this line, combined with a power spectrum similar to that seen in Seyfert galaxies, suggests that the majority of the X-ray emission in this object arises in or near the disk, and not in the jet.

Centralized Monitoring of the Microsoft Windows-based computers of the LHC Experiment Control Systems

International Nuclear Information System (INIS)

Varela Rodriguez, F

2011-01-01

The control system of each of the four major Experiments at the CERN Large Hadron Collider (LHC) is distributed over up to 160 computers running either Linux or Microsoft Windows. A quick response to abnormal situations of the computer infrastructure is crucial to maximize the physics usage. For this reason, a tool was developed to supervise, identify errors and troubleshoot such a large system. Although the monitoring of the performance of the Linux computers and their processes was available since the first versions of the tool, it is only recently that the software package has been extended to provide similar functionality for the nodes running Microsoft Windows as this platform is the most commonly used in the LHC detector control systems. In this paper, the architecture and the functionality of the Windows Management Instrumentation (WMI) client developed to provide centralized monitoring of the nodes running different flavour of the Microsoft platform, as well as the interface to the SCADA software of the control systems are presented. The tool is currently being commissioned by the Experiments and it has already proven to be very efficient optimize the running systems and to detect misbehaving processes or nodes.

Centralized Monitoring of the Microsoft Windows-based computers of the LHC Experiment Control Systems

Science.gov (United States)

Varela Rodriguez, F.

2011-12-01

The control system of each of the four major Experiments at the CERN Large Hadron Collider (LHC) is distributed over up to 160 computers running either Linux or Microsoft Windows. A quick response to abnormal situations of the computer infrastructure is crucial to maximize the physics usage. For this reason, a tool was developed to supervise, identify errors and troubleshoot such a large system. Although the monitoring of the performance of the Linux computers and their processes was available since the first versions of the tool, it is only recently that the software package has been extended to provide similar functionality for the nodes running Microsoft Windows as this platform is the most commonly used in the LHC detector control systems. In this paper, the architecture and the functionality of the Windows Management Instrumentation (WMI) client developed to provide centralized monitoring of the nodes running different flavour of the Microsoft platform, as well as the interface to the SCADA software of the control systems are presented. The tool is currently being commissioned by the Experiments and it has already proven to be very efficient optimize the running systems and to detect misbehaving processes or nodes.

7 CFR 160.97 - Publication.

Science.gov (United States)

2010-01-01

... 7 Agriculture 3 2010-01-01 2010-01-01 false Publication. 160.97 Section 160.97 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Standards... STANDARDS FOR NAVAL STORES Proceedings in Case of Violation § 160.97 Publication. Composite data regarding...

49 CFR 28.160 - Communications.

Science.gov (United States)

2010-10-01

... 49 Transportation 1 2010-10-01 2010-10-01 false Communications. 28.160 Section 28.160 Transportation Office of the Secretary of Transportation ENFORCEMENT OF NONDISCRIMINATION ON THE BASIS OF HANDICAP IN PROGRAMS OR ACTIVITIES CONDUCTED BY THE DEPARTMENT OF TRANSPORTATION § 28.160 Communications...

Resources | Efficient Windows Collaborative

Science.gov (United States)

Foundry Foundry New Construction Windows Window Selection Tool Selection Process Design Guidance Installation Replacement Windows Window Selection Tool Assessing Options Selection Process Design Guidance Installation Understanding Windows Benefits Design Considerations Measuring Performance Performance Standards

Links | Efficient Windows Collaborative

Science.gov (United States)

Foundry Foundry New Construction Windows Window Selection Tool Selection Process Design Guidance Installation Replacement Windows Window Selection Tool Assessing Options Selection Process Design Guidance Installation Understanding Windows Benefits Design Considerations Measuring Performance Performance Standards

Efficient Windows Collaborative | Home

Science.gov (United States)

Foundry Foundry New Construction Windows Window Selection Tool Selection Process Design Guidance Installation Replacement Windows Window Selection Tool Assessing Options Selection Process Design Guidance Installation Understanding Windows Benefits Design Considerations Measuring Performance Performance Standards

FAQ | Efficient Windows Collaborative

Science.gov (United States)

Foundry Foundry New Construction Windows Window Selection Tool Selection Process Design Guidance Installation Replacement Windows Window Selection Tool Assessing Options Selection Process Design Guidance Installation Understanding Windows Benefits Design Considerations Measuring Performance Performance Standards

Glossary | Efficient Windows Collaborative

Science.gov (United States)

Foundry Foundry New Construction Windows Window Selection Tool Selection Process Design Guidance Installation Replacement Windows Window Selection Tool Assessing Options Selection Process Design Guidance Installation Understanding Windows Benefits Design Considerations Measuring Performance Performance Standards

Windows® Internals

CERN Document Server

Russinovich, Mark E; Ionescu, Alex

2009-01-01

See how the core components of the Windows operating system work behind the scenes-guided by a team of internationally renowned internals experts. Fully updated for Windows Server 2008 and Windows Vista, this classic guide delivers key architectural insights on system design, debugging, performance, and support-along with hands-on experiments to experience Windows internal behavior firsthand.Delve inside Windows architecture and internals:Understand how the core system and management mechanisms work-from the object manager to services to the registryExplore internal system data structures usin

Windows Vista for Starters The Missing Manual

CERN Document Server

Pogue, David

2010-01-01

Fast-paced and easy to use, this concise book teaches you the basics of Windows Vista so you can start using this operating system right away. Written by "New York Times" columnist, bestselling author, Emmy-winning CBS News correspondent and Missing Manuals creator David Pogue, the book will help you: Navigate the desktop, including the fast, powerful and fully integrated desktop search functionUse the Media Center to record TV and radio, present photos, play music, and record all of these to a DVDBreeze across the Web with the vastly improved Internet Explorer 7 tabbed browserBecome familiar

50 CFR 550.160 - Communications.

Science.gov (United States)

2010-10-01

... 50 Wildlife and Fisheries 7 2010-10-01 2010-10-01 false Communications. 550.160 Section 550.160 Wildlife and Fisheries MARINE MAMMAL COMMISSION ENFORCEMENT OF NONDISCRIMINATION ON THE BASIS OF HANDICAP IN PROGRAMS OR ACTIVITIES CONDUCTED BY MARINE MAMMAL COMMISSION § 550.160 Communications. (a) The...

21 CFR 160.100 - Eggs.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 2 2010-04-01 2010-04-01 false Eggs. 160.100 Section 160.100 Food and Drugs FOOD... CONSUMPTION EGGS AND EGG PRODUCTS Requirements for Specific Standardized Eggs and Egg Products § 160.100 Eggs... identity for the food commonly known as eggs. ...

Association of morning blood pressure surge with carotid intima-media thickness and cardiac dysfunction in patients with cardiac syndrome-X.

Science.gov (United States)

Mahfouz, Ragab A; Goda, Mohammad; Galal, Islam; Ghareb, Mohamed S

2018-05-23

Background & hypothesis: We hypothesized that exaggerated morning blood pressure surge, may contribute in cardiac dysfunction and arterial stiffness in patients with cardiac syndrome X. Thus we investigated the impact of morning blood pressure surge on cardiac function and carotid intima-media thickness in subjects with cardiac syndrome X. We studied patients with cardiac syndrome X using ambulatory blood pressure monitoring and investigated the association of morning blood pressure surge with carotid intima thickness, left atrial volume index and left ventricular filling (E/e'). Seventy patients with cardiac syndrome X were enrolled for the study and compared with 70 age and sex matched controls. Patients with cardiac syndrome X were stratified based on the systolic morning blood pressure surge value of control subjects to patients with exaggerated blood pressure surge (n = 42) and those with normal morning blood pressure surge (n = 28). Basal heart rate (p blood pressure surge group than those with morning blood pressure surge group. Morning blood pressure surge was significantly correlated with carotid intima-media thickness, high sensitive C-reactive protein, left atrial volume index and E/e' ratio in patients with cardiac syndrome X. In multivariate analysis, exaggerated morning blood pressure surge was the only independent predictor of increased carotid intima-media thickness (OR = 2.379; p blood pressure surge is an independent predictor for arterial stiffness and diastolic dysfunction in patients with cardiac syndrome X.

Systematics of triaxial moment of inertia and deformation parameters (β, γ) in even-even nuclei of mass region A = 90-120

International Nuclear Information System (INIS)

Singh, Yuvraj; Gupta, D.K.; Singh, M.; Gupta, K.K.; Bihari, Chhail; Varshney, A.K.; Dhiman, S.K.

2012-01-01

The deformation parameter β and γ of the collective model of Bohr and Mottelson are basic descriptors of the nuclear equilibrium shape and structure. In recent past the sets of deformation parameters ((β, γ) have been extracted from both level energies and E2 transition rates in even Xe, Ba and Ce nuclei (A∼120-140) and Hf, W, Os, Pt and Hg nuclei (A∼160-200) using rigid triaxial rotor model of Davydov-Filippov (DF). Researcher have found that the values of β obtained separately from energy and transition rate (β e and β b respectively), though, are found almost equal in heavy mass region (A ∼160-200) but, not so in medium mass (A∼120-140) nuclei. This observation puts a question mark whether the ββ dependence of moment of inertia in hydrodynamic model is reliable. The purpose of the present work is to study a relatively lighter mass region (A∼90-120) where the gap between values of two sets of β may further increase. To improve the calculations for extracting β e , the use of Grodzins rule will be made along with uncertainties, since only through this rule the E2 1 + is related with β G (value of β for symmetric nucleus and evaluated using Grodzins rule)

Recent achievements in multi-keV x-ray microscopy

International Nuclear Information System (INIS)

Susini, J.; Barrett, R.; Salome, M.; Kaulich, B.

2002-01-01

X-ray microscopy (XRM) techniques are emerging as powerful and complementary tools for sub-micron investigations. Soft XRM traditionally offers the possibility to form direct images of thick hydrated biological material in near-native environments, at a spatial resolution well beyond that achievable with visible light microscopy. Natural contrast is available in the soft X-ray region, in the so-called 'water-window', due to the presence of absorption edges of the major constituents (C,N,O). Recent advances in manufacturing techniques have enlarged the accessible energy range of micro-focusing optics and offer new applications in a broad range of disciplines. XRM in the 1-20 keV energy range is better suited to map trace elements in fluorescence yield, 3-D tomographic imaging and in micro-diffraction. After a brief introduction to the principles and methods, the main attributes of X-ray microscopy will be presented. This presentation will be biased towards sub-micron microscopy developed at the ESRF in the 2-10 keV energy. Strengths and weaknesses of X-ray microscopy and spectro-microscopy techniques will be discussed and illustrated by examples in biology, materials sciences and geology. (authors)

12 CFR 410.160 - Communications.

Science.gov (United States)

2010-01-01

... 12 Banks and Banking 4 2010-01-01 2010-01-01 false Communications. 410.160 Section 410.160 Banks and Banking EXPORT-IMPORT BANK OF THE UNITED STATES ENFORCEMENT OF NONDISCRIMINATION ON THE BASIS OF HANDICAP IN PROGRAMS OR ACTIVITIES CONDUCTED BY EXPORT-IMPORT BANK OF THE UNITED STATES § 410.160...

45 CFR 160.516 - Discovery.

Science.gov (United States)

2010-10-01

... 45 Public Welfare 1 2010-10-01 2010-10-01 false Discovery. 160.516 Section 160.516 Public Welfare... ADMINISTRATIVE REQUIREMENTS Procedures for Hearings § 160.516 Discovery. (a) A party may make a request to... forms of discovery, other than those permitted under paragraph (a) of this section, are not authorized...

Insulin stimulates the tyrosine phosphorylation of a Mr = 160,000 glycoprotein in adipocyte plasma membranes

International Nuclear Information System (INIS)

Yu, K.T.; Khalaf, N.; Czech, M.P.

1986-01-01

In an attempt to identify putative substrates for the insulin receptor kinase, adipocyte plasma membranes were incubated with [γ- 32 P]ATP in the presence and absence of insulin. Insulin stimulates the tyrosine phosphorylation of its receptor β subunit but does not detectably alter the phosphorylation of other membrane proteins. In contrast, when plasma membranes from insulin-treated adipocytes are phosphorylated, the 32 P-labeling of a Mr=160,000 species (p160) and insulin receptor β subunit are markedly increased when compared to controls. p160 exhibits a rapid response (max. at 1 min) and high sensitivity (ED 50 = 2 x 10 -10 M) to insulin. The stimulatory effect of insulin on the phosphorylation of p160 is rapidly reversed following the addition of anti-insulin serum. Cold chase experiments indicate that insulin promotes the phosphorylation of p160 rather than inhibiting its dephosphorylation. p160 is a glycoprotein as evidenced by its adsorption to immobilized lectins and does not represent the insulin receptor precursor. The action of insulin on p160 tyrosine phosphorylation is mimicked by concanavalin A but not by EGF and other insulin-like agents such as hydrogen peroxide and vanadate. These results suggest that p160 tyrosine phosphorylation is an insulin receptor-mediated event and may participate in signalling by the insulin receptor

The importance of surrounding tissues and window settings for contouring of moving targets

Energy Technology Data Exchange (ETDEWEB)

Borm, Kai Joachim [Technische Universitaet Muenchen, Medical School, Munich (Germany); Klinikum rechts der Isar, Technische Universitaet Muenchen, Department of Radiation Oncology, Munich (Germany); Oechsner, Markus; Berndt, Johannes; Combs, Stephanie Elisabeth; Molls, Michael; Duma, Marciana Nona [Klinikum rechts der Isar, Technische Universitaet Muenchen, Department of Radiation Oncology, Munich (Germany)

2015-09-15

The aim of the study was to assess the importance of surrounding tissues for the delineation of moving targets in tissue-specific phantoms and to find optimal settings for lung, soft tissue, and liver tumors. Tumor movement was simulated by a water-filled table tennis ball (target volume, TV). Three phantoms were created: corkboards to simulate lung tissue (lung phantom, LunPh), animal fat as fatty soft tissue (fatty tissue phantom, FatPh), and water enhanced with contrast medium as the liver tissue (liver phantom, LivPh). Slow planning three-dimensional compute tomography images (3D-CTs) were acquired with and without phantom movements. One-dimensional tumor movement (1D), three-dimensional tumor movement (3D), as well as a real patient's tumor trajectories were simulated. The TV was contoured using two lung window settings, two soft-tissue window settings, and one liver window setting. The volumes were compared to mathematical calculated values. TVs were underestimated in all phantoms due to movement. The use of soft-tissue windows in the LivPh led to a significantunderestimation of the TV (70.8 % of calculated TV). When common window settings [LunPh + 200 HU/-1,000 HU (upper window/lower window threshold); FatPh: + 240 HU/-120 HU; LivPh: + 175 HU/+ 50 HU] were used, the contoured TVs were: LivPh, 84.0 %; LunPh, 93.2 %, and FatPh, 92.8 %. The lower window threshold had a significant impact on the size of the delineated TV, whereas changes of the upper threshold led only to small differences. The decisive factor for window settings is the lower window threshold (for adequate TV delineation in the lung and fatty-soft tissue it should be lower than density values of surrounding tissue). The use of a liver window should be considered. (orig.) [German] Das Ziel dieser Arbeit war es, den Einfluss des umgebenden Gewebes auf die Konturierung bewegter Objekte zu untersuchen. Um die optimalen CT-Fensterungen fuer Lungen-, Weichteil- und Lebertumoren zu bestimmen

Characterization of a pulsed x-ray source for fluorescent lifetime measurements

International Nuclear Information System (INIS)

Blankespoor, S.C.; Derenzo, S.E.; Moses, W.W.; Rossington, C.S.; Ito, M.; Oba, K.

1994-01-01

To search for new, fast, inorganic scintillators, the authors have developed a bench-top pulsed x-ray source for determining fluorescent lifetimes and wavelengths of compounds in crystal or powdered form. This source uses a light-excited x-ray tube which produces x-rays when light from a laser diode strikes its photocathode. The x-ray tube has a tungsten anode, a beryllium exit window, a 30 kV maximum tube bias, and a 50 μA maximum average cathode current. The laser produces 3 x 10 7 photons at 650 nm per ∼100 ps pulse, with up to 10 7 pulses/sec. The time spread for the laser diode, x-ray tube, and a microchannel plate photomultiplier tube is less than 120 ps fwhm. The mean x-ray energy at tube biases of 20, 25, and 30 kV is 9.4, 10.3, and 11.1 keV, respectively. The authors measured 140, 230, and 330 x-ray photons per laser diode pulse per steradian, at tube biases of 20, 25, and 30 kV, respectively. Background x-rays due to dark current occur at a rate of 1 x 10 6 and 3 x 10 6 photons/sec/steradian at biases of 25 and 30 kV, respectively. Data characterizing the x-ray output with an aluminum filter in the x-ray beam are also presented

Windows 2012 Server network security securing your Windows network systems and infrastructure

CERN Document Server

Rountree, Derrick

2013-01-01

Windows 2012 Server Network Security provides the most in-depth guide to deploying and maintaining a secure Windows network. The book drills down into all the new features of Windows 2012 and provides practical, hands-on methods for securing your Windows systems networks, including: Secure remote access Network vulnerabilities and mitigations DHCP installations configuration MAC filtering DNS server security WINS installation configuration Securing wired and wireless connections Windows personal firewall

Windows 8.1 bible

CERN Document Server

Boyce, Jim; Tidrow, Rob

2014-01-01

Windows 8.1 coverage that goes above and beyond all competitors? Serving as an evolutionary update to Windows 8, Windows 8.1 provides critical changes to parts of Windows 8, such as greater customization of the interface and boot operations, return of a 'start button' that reveals apps, greater integration between the two interfaces, and updates to apps. Weighing in at nearly 1000 pages, Windows 8.1 Bible provides deeper Windows insight than any other book on the market. It's valuable for both professionals needing a guide to the nooks and crannies of Windows and regular users wanting a wide

Electrochemical behavior of Ni{sub x}W{sub 1-x} materials as catalyst for hydrogen evolution reaction in alkaline media

Energy Technology Data Exchange (ETDEWEB)

Oliver-Tolentino, Miguel A. [UPIBI-IPN, Departamento de Ciencias Basicas, Av. Acueducto s/n, Barrio La Laguna, Col. Ticoman, Mexico D.F. 07340 (Mexico); Arce-Estrada, Elsa M. [ESIQIE-IPN Departamento de Ingenieria en Metalurgia y Materiales, UPALM, UPALM, Mexico D.F. 07738 (Mexico); Cortes-Escobedo, Claudia A. [Centro de Investigacion e Innovacion Tecnologica del IPN, Cda. Cecati s/n, Col. Sta. Catarina, CP 02250 Azcapotzalco D.F. (Mexico); Bolarin-Miro, Ana M.; Sanchez-De Jesus, Felix [Area Academica de Ciencias de la Tierra y Materiales, Universidad Autonoma del Estado de Hidalgo, CU, Carr. Pachuca-Tulancingo Km. 4.5, Mineral de la Reforma, CP 42184 Hidalgo (Mexico); Gonzalez-Huerta, Rosa de G. [ESIQIE-IPN, Departamento de Ingenieria Quimica - Laboratorio de Electroquimica y Corrosion, Edif. Z-5 3er piso, UPALM, Mexico D.F. 07738 (Mexico); Manzo-Robledo, Arturo, E-mail: amanzor@ipn.mx [ESIQIE-IPN, Departamento de Ingenieria Quimica - Laboratorio de Electroquimica y Corrosion, Edif. Z-5 3er piso, UPALM, Mexico D.F. 07738 (Mexico)

2012-09-25

Highlights: Black-Right-Pointing-Pointer The electrochemical techniques used in this study elucidated the Ni-W surface state. Black-Right-Pointing-Pointer The Ni-W materials were effective for the hydrogen evolution reaction. Black-Right-Pointing-Pointer The prepared alloys exhibited higher catalytic activity than their precursors. Black-Right-Pointing-Pointer The preparation method is relatively simple and effective procedure. - Abstract: In the present work, results of electrochemical evaluation, as well as morphological and structural characterization of Ni{sub x}W{sub 1-x} materials with x = 0.77, 0.64, 0.4, 0.19 and 0.07 processed by means of high energy ball milling from high purity powders are presented. Also, the electrocatalytic performance on the hydrogen evolution reaction (HER) of the Ni{sub x}W{sub 1-x} materials evaluated by linear polarization and cyclic voltammetry techniques in alkaline media at room temperature is discussed. The structural and morphological characterization of the as-prepared materials was carried out using X-ray diffraction (XRD) and scanning electron microscopy (SEM). Results indicated a small-particle clusters and solid solution formation. According to the kinetics parameters the best electrocatalytic activity was observed at Ni{sub 64}W{sub 36}.

Acoustic Reflex Screening of Conductive Hearing Loss for Third Window Disorders.

Science.gov (United States)

Hong, Robert S; Metz, Christopher M; Bojrab, Dennis I; Babu, Seilesh C; Zappia, John; Sargent, Eric W; Chan, Eleanor Y; Naumann, Ilka C; LaRouere, Michael J

2016-02-01

This study examines the effectiveness of acoustic reflexes in screening for third window disorders (eg, superior semicircular canal dehiscence) prior to middle ear exploration for conductive hearing loss. Case series with chart review. Outpatient tertiary otology center. A review was performed of 212 ears with acoustic reflexes, performed as part of the evaluation of conductive hearing loss in patients without evidence of chronic otitis media. The etiology of hearing loss was determined from intraoperative findings and computed tomography imaging. The relationship between acoustic reflexes and conductive hearing loss etiology was assessed. Eighty-eight percent of ears (166 of 189) demonstrating absence of all acoustic reflexes had an ossicular etiology of conductive hearing loss. Fifty-two percent of ears (12 of 23) with at least 1 detectable acoustic reflex had a nonossicular etiology. The positive and negative predictive values for an ossicular etiology were 89% and 57% when acoustic reflexes were used alone for screening, 89% and 39% when third window symptoms were used alone, and 94% and 71% when reflexes and symptoms were used together, respectively. Acoustic reflex testing is an effective means of screening for third window disorders in patients with a conductive hearing loss. Questioning for third window symptoms should complement screening. The detection of even 1 acoustic reflex or third window symptom (regardless of reflex status) should prompt further workup prior to middle ear exploration. © American Academy of Otolaryngology—Head and Neck Surgery Foundation 2015.

Genetic deletion of ABP-120 alters the three-dimensional organization of actin filaments in Dictyostelium pseudopods

OpenAIRE

1995-01-01

This study extends the observations on the defects in pseudopod formation of ABP-120+ and ABP-120- cells by a detailed morphological and biochemical analysis of the actin based cytoskeleton. Both ABP-120+ and ABP-120- cells polymerize the same amount of F-actin in response to stimulation with cAMP. However, unlike ABP-120+ cells, ABP-120- cells do not incorporate actin into the Triton X-100-insoluble cytoskeleton at 30-50 s, the time when ABP-120 is incorporated into the cytoskeleton and when...

Mediated Windows: The Use of Framing and Transparency in Designing for Presence

Directory of Open Access Journals (Sweden)

Charlie Gullström

2014-07-01

Full Text Available This paper explores the fusion of architecture and media technology that facilitates collaborative practices across spatial extensions: video-mediated spaces. The example presented is a mediated extension of the Museum of National Antiquities in Stockholm to a neighbouring park area and archaeological excavation site in 2008, referred to as a mediated window, or a glass-door. The concepts framing and transparency are used to outline the significance of windows and glazing in architecture and art. The author then considers the potential contribution of architecture in representing the passage from indoors to outdoors and designing for presence. Presence design assumes a contribution from architects to presence research, a currently diversified field, spanning media-space research, cognitive science, interaction design, ubiquitous computing, second-order cybernetics, and computer-supported collaborative work, but in which architecture and artistic practices are less represented.The paper thereby addresses the potential of an extended architectural practice, which incorporates the design of mediated spaces, and outlines presence design as a transdisciplinary practice in which presence research meets architectural design, and spatial and aesthetic conceptual tools, derived from related visual practices, may be productively applied.

Culture media used in the micropropagation of orchids hybrids

Directory of Open Access Journals (Sweden)

Luzia Yuriko Miyata

2014-09-01

Full Text Available In orchid cultivation, tissue culture has been an important and effective tool for obtaining good quality seedlings on a large scale and within a short period of time. This study aims to evaluate culture media on the in vitro growth and development of orchid hybrids. Seedlings 1-1.5 cm long, deriving from in vitro germination of seeds, were inoculated in 250 mL flasks containing 50 mL of culture medium, with salts from the media where each of them were treated. Treatments consisted of applying culture media (MS; DSD1; Knudson; B5; and WPM, combined with 5 orchid hybrids (CW1, CW2, CW3, CI e BLC. The media were added 2 g L-1 of activated charcoal and solidified with 5 g L-1 of agar, and their pH was adjusted to 5.8 ± 0.1, before autoclaving at 121°C and at 1.1 atm for 20 minutes. After sterilization of media, seedlings were inoculated in a laminar flow chamber and then kept in a growth room at the temperature of 25 ± 1ºC, with photoperiod of 16 h and irradiance of 32 ?mol.m–2.s–1. The experimental design was completely randomized, in a factorial 5 x 5 scheme, containing 6 seedlings per repetition. After 120 days, we evaluated root number, shoot number, leaf and root length, and fresh root weight. In in vitro cultivation of orchids, the media standing out are MS and DSD1 and the hybrids CI, CW1, and BLC.

Application of X-ray CT investigation of CO{sub 2}-brine flow in porous media

Energy Technology Data Exchange (ETDEWEB)

Jiang, Lanlan; Liu, Yu; Song, Yongchen; Yang, Mingjun; Zhao, Yuechao; Zhao, Jiafei; Zhang, Yi; Shen, Zijian [Dalian University of Technology, Key Laboratory of Ocean Energy Utilization and Energy Conservation of Ministry of Education, Dalian (China); Xue, Ziqiu [Research Institute of Innovative Technology for the Earth, Kizugawa City, Kyoto (Japan); Suekane, Tetsuya [Tokyo Institute Technology, Department of Energy Sciences, Nagatsuta, Yokohama (Japan)

2015-05-15

A clear understanding of two-phase flows in porous media is important for investigating CO{sub 2} geological storage. In this study, we conducted an experiment of CO{sub 2}/brine flow process in porous media under sequestration conditions using X-ray CT technique. The flow properties of relative permeability, porosity heterogeneity, and CO{sub 2} saturation were observed in this experiment. The porous media was packed with glass beads having a diameter of 0.2 mm. The porosity distribution along the flow direction is heterogeneous owing to the diameter and shape of glass beads along the flow direction. There is a relationship between CO{sub 2} saturation and porosity distribution, which changes with different flow rates and fractional flows. The heterogeneity of the porous media influences the distribution of CO{sub 2}; moreover, gravity, fractional flows, and flow rates influence CO{sub 2} distribution and saturation. The relative permeability curve was constructed using the steady-state method. The results agreed well with the relative permeability curve simulated using pore-network model. (orig.)

Optimal Design for the Diffusion Plate with Nanoparticles in a Diffusive Solar Cell Window by Mie Scattering Simulation

Directory of Open Access Journals (Sweden)

Ruei-Tang Chen

2013-01-01

Full Text Available A diffusive solar cell window comprises a diffusion plate with TiO2 nanoparticles sandwiched between two glass layers. It is a simple, inexpensive, easy-to-made, and highly reliable transparent solar energy module. To improve its power generation efficiency as well as maintain indoor natural lighting, we examined the scattering mechanism in the diffusion plate with TiO2 nanoparticles within a diffusive solar cell window by Mie scattering simulations. In this work, a multiwavelength ASAP ray tracing model for a diffusive solar cell window with acceptable accuracy was developed to investigate the influence of the diffusion plate design parameter, mainly concentration of a diffusion plate with determined particle size distribution, on power generation efficiency and color shift of transmitted sun light. A concept of “effective average radius” was proposed to account for the equivalent scattering effect of a size distribution of quasispherical particles. Simulation results demonstrated that both the transmitted light and its correlated color temperature decreased as the concentration increased for a large-size diffusive solar cell window. However, there existed a maximum power generation efficiency at around 160 ppm concentration. The optimal design for a large-size diffusion plate inside a diffusive solar cell window by taking indoor lighting into account was suggested based on the simulation results.

An Evaluation of Windows-Based Computer Forensics Application Software Running on a Macintosh

OpenAIRE

Gregory H. Carlton

2008-01-01

The two most common computer forensics applications perform exclusively on Microsoft Windows Operating Systems, yet contemporary computer forensics examinations frequently encounter one or more of the three most common operating system environments, namely Windows, OS-X, or some form of UNIX or Linux. Additionally, government and private computer forensics laboratories frequently encounter budget constraints that limit their access to computer hardware. Currently, Macintosh computer systems a...

Improved image quality and detectability of hypovascular liver metastases on DECT with different adjusted window settings

Energy Technology Data Exchange (ETDEWEB)

Altenbernd, Jens; Forsting, Michael; Lauenstein, Thomas; Wetter, Axel [Duisburg-Essen Univ., Essen (Germany). Dept. of Diagnostic and Interventional Radiology and Neuroradiology

2017-03-15

To investigate dual-energy CT of hypovascular liver metastases (LMs) with special focus on window settings (WSs). The aim of the study is to investigate the extent to which adapted WSs and the low-energy images of DECT improve the visibility especially of smaller LMs. 30 patients with LMs of colorectal cancer were investigated with DECT of the liver. In each patient contrast-enhanced DECT imaging with portal-venous delay was performed. The total number, mean number and conspicuity (1= excellent - 5 = poor) of LMs were documented on 80-kVp images and virtual 120-kVp images with different WSs (25/200 HU, 50/200, 75/200 HU, 25/350 HU, 50/350 HU, 75/350 HU, 25/500 HU, 50/500 HU, 75/500 HU). The attenuation (HU) of LMs and several anatomic regions and the background noise on 80 kVp images and virtual 120 kVp images were documented. Signal (liver)/noise and liver/LM ratio (SNR/LLMR) were calculated. The total number of LMs depending on size (<1cm, 1-2cm, >2cm) on 80 kVp images and virtual 120 kVp images with previously investigated best and regular WSs were documented. The highest total number, mean number per patient and total number of LMs <1cm were detected with the WS 25/350 HU on 80kVp images (7.0; p = 0.02/218; p = 0.01/64;p<0.001) compared to the WS 75/200 HU on virtual 120 kVp images and the regular WS 50/350 HU on 80 kVp images and virtual 120 kVp images. The best conspicuity of LMs on 80 kVp images was documented with the WS 25/350 HU compared to the best WS on virtual 120 kVp images with 75/200 HU (1.2 vs. 2.5; p = 0.01). HU of normal liver, aorta, SNR and LLMR differed significantly between 80 kVp images and virtual 120 kVp images (128.1 vs. 93.6; < 0.05/192.8 vs. 131.4; < 0.05/10.3 vs. 8.1; p < 0.05/2.8 vs. 2.1; p < 0.05). Low kVp images of DECT datasets are more precise in detecting hypovascular liver metastases than virtual 120 kVp images. Dedicated window settings have a relevant influence on conspicuity.

Acoustic window planning for ultrasound acquisition.

Science.gov (United States)

Göbl, Rüdiger; Virga, Salvatore; Rackerseder, Julia; Frisch, Benjamin; Navab, Nassir; Hennersperger, Christoph

2017-06-01

Autonomous robotic ultrasound has recently gained considerable interest, especially for collaborative applications. Existing methods for acquisition trajectory planning are solely based on geometrical considerations, such as the pose of the transducer with respect to the patient surface. This work aims at establishing acoustic window planning to enable autonomous ultrasound acquisitions of anatomies with restricted acoustic windows, such as the liver or the heart. We propose a fully automatic approach for the planning of acquisition trajectories, which only requires information about the target region as well as existing tomographic imaging data, such as X-ray computed tomography. The framework integrates both geometrical and physics-based constraints to estimate the best ultrasound acquisition trajectories with respect to the available acoustic windows. We evaluate the developed method using virtual planning scenarios based on real patient data as well as for real robotic ultrasound acquisitions on a tissue-mimicking phantom. The proposed method yields superior image quality in comparison with a naive planning approach, while maintaining the necessary coverage of the target. We demonstrate that by taking image formation properties into account acquisition planning methods can outperform naive plannings. Furthermore, we show the need for such planning techniques, since naive approaches are not sufficient as they do not take the expected image quality into account.

Location-Based Top-k Term Querying over Sliding Window

KAUST Repository

Xu, Ying

2017-10-03

In part due to the proliferation of GPS-equipped mobile devices, massive svolumes of geo-tagged streaming text messages are becoming available on social media. It is of great interest to discover most frequent nearby terms from such tremendous stream data. In this paper, we present novel indexing, updating, and query processing techniques that are capable of discovering top-k locally popular nearby terms over a sliding window. Specifically, given a query location and a set of geo-tagged messages within a sliding window, we study the problem of searching for the top-k terms by considering both the term frequency and the proximities between the messages containing the term and the query location. We develop a novel and efficient mechanism to solve the problem, including a quad-tree based indexing structure, indexing update technique, and a best-first based searching algorithm. An empirical study is conducted to show that our proposed techniques are efficient and fit for users’ requirements through varying a number of parameters.

Location-Based Top-k Term Querying over Sliding Window

KAUST Repository

Xu, Ying; Chen, Lisi; Yao, Bin; Shang, Shuo; Zhu, Shunzhi; Zheng, Kai; Li, Fang

2017-01-01

In part due to the proliferation of GPS-equipped mobile devices, massive svolumes of geo-tagged streaming text messages are becoming available on social media. It is of great interest to discover most frequent nearby terms from such tremendous stream data. In this paper, we present novel indexing, updating, and query processing techniques that are capable of discovering top-k locally popular nearby terms over a sliding window. Specifically, given a query location and a set of geo-tagged messages within a sliding window, we study the problem of searching for the top-k terms by considering both the term frequency and the proximities between the messages containing the term and the query location. We develop a novel and efficient mechanism to solve the problem, including a quad-tree based indexing structure, indexing update technique, and a best-first based searching algorithm. An empirical study is conducted to show that our proposed techniques are efficient and fit for users’ requirements through varying a number of parameters.

DMPD: Macrophage activation through CCR5- and CXCR4-mediated gp120-elicited signalingpathways. [Dynamic Macrophage Pathway CSML Database

Lifescience Database Archive (English)

Full Text Available 12960231 Macrophage activation through CCR5- and CXCR4-mediated gp120-elicited sign...82. Epub 2003 Jul 22. (.png) (.svg) (.html) (.csml) Show Macrophage activation through CCR5- and CXCR4-media...on through CCR5- and CXCR4-mediated gp120-elicited signalingpathways. Authors Lee C, Liu QH, Tomkowicz B, Yi

Efficient Windows Collaborative

Energy Technology Data Exchange (ETDEWEB)

Nils Petermann

2010-02-28

The project goals covered both the residential and commercial windows markets and involved a range of audiences such as window manufacturers, builders, homeowners, design professionals, utilities, and public agencies. Essential goals included: (1) Creation of 'Master Toolkits' of information that integrate diverse tools, rating systems, and incentive programs, customized for key audiences such as window manufacturers, design professionals, and utility programs. (2) Delivery of education and outreach programs to multiple audiences through conference presentations, publication of articles for builders and other industry professionals, and targeted dissemination of efficient window curricula to professionals and students. (3) Design and implementation of mechanisms to encourage and track sales of more efficient products through the existing Window Products Database as an incentive for manufacturers to improve products and participate in programs such as NFRC and ENERGY STAR. (4) Development of utility incentive programs to promote more efficient residential and commercial windows. Partnership with regional and local entities on the development of programs and customized information to move the market toward the highest performing products. An overarching project goal was to ensure that different audiences adopt and use the developed information, design and promotion tools and thus increase the market penetration of energy efficient fenestration products. In particular, a crucial success criterion was to move gas and electric utilities to increase the promotion of energy efficient windows through demand side management programs as an important step toward increasing the market share of energy efficient windows.

BASAL MEDIA FORMULATION USING CANAVALIA ENSIFORMIS AS CARBON AND NITROGEN SOURCE FOR THE GROWTH OF SOME FUNGI SPECIES

Directory of Open Access Journals (Sweden)

B.J. Akinyele2

2012-02-01

Full Text Available The possibility of developing alternative media to commercial potato dextrose agar was assessed using, Canavalia ensiformis (Linn (jack beans as carbon and nitrogen source. Six leguminous meal media were used as substitute for either carbon or nitrogen or both, while potato dextrose broth (PDB was used as a positive control and basal medium as a negative control. Six species of fungi Aspergillus flavus, A. niger, Meria coniospora, Mucor sp, Neurospora crassa and Rhizopus oryzae were aseptically inoculated into the formulated media and allowed to grow. Their mycelia dry weights were taken after 24, 48, 72, 96 and 120 hours. Growth of all fungal species was observed to be slightly lower, about the same or better in the formulated media relative to the control. Aspergillus flavus had its highest biomass of 1.70g in the media formulated with Canavalia ensiformis as the carbon source relative to 1.42g as the standard at the 120 hour. A. niger had a growth of 0.62g relative to 0.61g at 120 hours of the control. Meria coniospora had a growth of 0.27g relative to 0.38g at 120 hours. Mucor sp had a growth of 0.54g relative to 0.44g at 120 hours. Neurospora crassa had a growth of 1.05g relative to 0.24g at 120 hours. Rhizopus oryzae had a growth of 0.14g relative to 0.25g at 120 hours. The study revealed that Canavalia ensiformis contains minerals and nutrients that is able to provide the nutritional requirements of these fungi. Thus, it can be used as an alternative material in the preparation of culture media for in vitro cultivation of these fungi for teaching and research purposes.

Reversible magnetic-field-induced martensitic transformation over a wide temperature window in Ni42-xCoxCu8Mn37Ga13 alloys

Science.gov (United States)

Hua, Hui; Wang, Jingmin; Jiang, Chengbao; Xu, Huibin

2018-05-01

Ni42-xCoxCu8Mn37Ga13 (0 ≤ x ≤ 14) alloys are reported to exhibit a magnetostructural transition from weakly-magnetic martensite to ferromagnetic austenite over a rather wide temperature window ranging from 200 K to 380 K. Simultaneously a large magnetization change Δσ of up to 105 Am2 kg-1 is obtained at the martensitic transformation. A reversible magnetic-field-induced martensitic transformation is realized, resulting in a large magnetocaloric effect related to the high magnetic entropy change with a broad working temperature span. This work shows how it is possible to effectively tailor the magnetostructural transition in Ni-Mn-Ga alloys so as to achieve a reversible magnetic-field-induced martensitic transformation and associated functionalities.

Direct measurements of the 160.01-min oscillation in the solar radio brightness

International Nuclear Information System (INIS)

Efanov, V.A.; Moiseev, I.G.; Nesterov, N.S.

1983-01-01

Direct (nondifferential) brightness measurements of the quiet sun at lambda = 8.2 and 13.5 mm, corrected by the Bouguer law for absorption in the terrestrial atmosphere, confirm the presence of a 160.009 +- 0.002 min periodicity. At the two wavelengths the relative amplitudes are roughly-equal0.6 x 10 -3 , 1 x 10 -3 . Maximum radio brightness occurs at the phase when optical data indicate the photosphere radius is largest

X-ray spectroscopy of electronic quasimolecules. I. Isolation and study of particular K molecular-orbital transitions

International Nuclear Information System (INIS)

Liarokapis, E.; Zouros, T.J.M.; Greenberg, J.S.

1987-01-01

Selected K molecular-orbital (MO) transitions in collisions of 100-, 160-, and 200-MeV /sup 93/Nb on /sup 93/Nb and 200-MeV /sup 93/Nb on /sup 120/Sn have been isolated in a MO x-ray--K x-ray coincidence measurement. This experiment exploits the cascade relationship between the MO x rays emitted in transitions from the (2pπ/sub x/, 2pσ) MO's into the 1sσ MO and the characteristic K x ray which follows from the filling of the ensuing vacancy in the projectile or target atoms after their separation. In both symmetric and asymmetric systems, most of the high-energy MO x rays (C2 radiation) were found to be in coincidence with characteristic K x rays while the low-energy MO x rays (C1 radiation) were not correlated to the K x rays. Noncascade processes due to multiple vacancies in the 1sσ and 2pσ MO's were also found to contribute a small amount to the true MO x-ray--K x-ray coincidences. Theoretical estimates of the relative contributions of the isolated transitions as well as contributions from multiple vacancies are discussed

Anomalous optical behavior of biological media: modifying the optical window of myocardial tissues

Science.gov (United States)

Splinter, Robert; Raja, M. Yasin A.; Svenson, Robert H.

1996-05-01

In medical experimental and clinical treatment modalities of light, laser photocoagulation of ventricular tachycardia amongst others, the success of the application relies on whether or not the procedure operates in the optical window of the light-tissue interaction. The optical window of biological tissues can be determined by spectral scans of the optical properties. Optical anomalies may result from the irradiance, the wavelength, or from the tissue composition itself. The transmission of cw Nd:YAG laser light on myocardial tissue showed a nonlinearity in the transmission curve at approximately 3 kW/mm2 irradiance. The total attenuation coefficient dropped sharp from 1.03 plus or minus 0.04 mm-1 to 0.73 plus or minus 0.05 mm-1 at this point in the curve. On the other hand, aneurysm tissue has a highly organized fiber structure, which serves as light-guides, since the transmission of light along the length of the collagen fibers is approximately 50% higher than the transmission perpendicular to the fiber orientation. In addition, changes in optical properties due to tissue phase changes also influence the penetration depth. These phenomena can be utilized to manipulate the optical penetration to an advantage.

ITER ECRH upper launcher torus diamond window – Prototyping, testing and qualification

Energy Technology Data Exchange (ETDEWEB)

Schreck, Sabine, E-mail: sabine.schreck@kit.edu [Karlsruhe Institute of Technology, Institute for Applied Materials, Association KIT-EURATOM, P.O. Box 3640, D-76021 Karlsruhe (Germany); Aiello, Gaetano; Meier, Andreas; Strauss, Dirk [Karlsruhe Institute of Technology, Institute for Applied Materials, Association KIT-EURATOM, P.O. Box 3640, D-76021 Karlsruhe (Germany); Ikeda, Ryosuke; Oda, Yasuhisa; Sakamoto, Keishi; Takahashi, Koji [Japan Atomic Energy Agency (JAEA), Plasma Heating Technology Group, 801-1 Mukoyama, Naka, Ibaraki 311-0193 (Japan); Scherer, Theo [Karlsruhe Institute of Technology, Institute for Applied Materials, Association KIT-EURATOM, P.O. Box 3640, D-76021 Karlsruhe (Germany)

2015-10-15

Highlights: • The diamond window prototype shows a very good transmission capability during high power RF experiments. • An ad-hoc qualification programme for the diamond torus window is being developed (contract between KIT and F4E). • The window design has been updated focused on its mechanical integrity and manufacturing aspects. - Abstract: The diamond window assembly is part of the ITER primary vacuum boundary and acts as the first tritium barrier and therefore it is classified as Safety/Protection Important Component (SIC/PIC). It consists of an ultra-low loss CVD diamond disk mounted in a system of metallic parts (copper/steel) and has to fulfil adequate transmission capability for high power mm-waves. High power RF experiments with a 1st window prototype had shown parasitic heating due to small gaps in the housing. After a design optimization directed to the mm-wave properties, the parasitic excitations of oscillations have been avoided in a 2nd prototype. This one is equipped with inserted waveguide structures, which cover gaps in the metallic structure of the window housing. From high power RF-measurements with a 0.86 MW/100 s pulse a loss tangent of 7.1 × 10{sup −6} could be estimated, corresponding to an increase of temperature of only 120 mK between inlet and outlet of the cooling system. The diamond window assemblies cannot be entirely covered by codes and standards. To comply with the French safety regulations, instead an ad-hoc qualification programme is required, being developed in the framework of a contract between KIT and F4E. A new prototype (3rd) will be built, which is designed to fit to the single HELICOFLEX sealed waveguide structures of the ex-vessel mm-system of the EC upper launcher (UL). The testing programme ranges from mechanical to vacuum tests up to dielectric loss measurements at low and high power. A clear definition of the testing requirements and of the acceptance criteria is necessary as well as a complete

Windows 10 for dummies

CERN Document Server

Rathbone, Andy

2015-01-01

The fast and easy way to get up and running with Windows 10 Windows 10 For Dummies covers the latest version of Windows and gets you up and running with the changes and new features you'll find in this updated operating system. Packed with time-saving tips to help you get the most out of the software, this helpful Windows 10 guide shows you how to manage Windows tasks like navigating the interface with a mouse or touchscreen, connecting to the web, and troubleshooting problems and making quick fixes. Assuming no prior knowledge of the software, Windows 10 For Dummies addresses the updates to

7 CFR 65.160 - Ground chicken.

Science.gov (United States)

2010-01-01

... 7 Agriculture 3 2010-01-01 2010-01-01 false Ground chicken. 65.160 Section 65.160 Agriculture... OF BEEF, PORK, LAMB, CHICKEN, GOAT MEAT, PERISHABLE AGRICULTURAL COMMODITIES, MACADAMIA NUTS, PECANS, PEANUTS, AND GINSENG General Provisions Definitions § 65.160 Ground chicken. Ground chicken means...

46 CFR 160.002-4 - Construction.

Science.gov (United States)

2010-10-01

... 46 Shipping 6 2010-10-01 2010-10-01 false Construction. 160.002-4 Section 160.002-4 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) EQUIPMENT, CONSTRUCTION, AND MATERIALS... and 5 § 160.002-4 Construction. (a) General. This specification covers life preservers which...

46 CFR 160.174-9 - Construction.

Science.gov (United States)

2010-10-01

... 46 Shipping 6 2010-10-01 2010-10-01 false Construction. 160.174-9 Section 160.174-9 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) EQUIPMENT, CONSTRUCTION, AND MATERIALS: SPECIFICATIONS AND APPROVAL LIFESAVING EQUIPMENT Thermal Protective Aids § 160.174-9 Construction. (a) General...

46 CFR 160.171-9 - Construction.

Science.gov (United States)

2010-10-01

... 46 Shipping 6 2010-10-01 2010-10-01 false Construction. 160.171-9 Section 160.171-9 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) EQUIPMENT, CONSTRUCTION, AND MATERIALS: SPECIFICATIONS AND APPROVAL LIFESAVING EQUIPMENT Immersion Suits § 160.171-9 Construction. (a) General. Each...

46 CFR 160.042-3 - Construction.

Science.gov (United States)

2010-10-01

... 46 Shipping 6 2010-10-01 2010-10-01 false Construction. 160.042-3 Section 160.042-3 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) EQUIPMENT, CONSTRUCTION, AND MATERIALS: SPECIFICATIONS AND APPROVAL LIFESAVING EQUIPMENT Skids, Liferaft, for Merchant Vessels § 160.042-3 Construction...

46 CFR 160.047-4 - Construction.

Science.gov (United States)

2010-10-01

... 46 Shipping 6 2010-10-01 2010-10-01 false Construction. 160.047-4 Section 160.047-4 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) EQUIPMENT, CONSTRUCTION, AND MATERIALS... and Child § 160.047-4 Construction. (a) General. This specification covers buoyant vests which...

46 CFR 160.176-9 - Construction.

Science.gov (United States)

2010-10-01

... 46 Shipping 6 2010-10-01 2010-10-01 false Construction. 160.176-9 Section 160.176-9 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) EQUIPMENT, CONSTRUCTION, AND MATERIALS: SPECIFICATIONS AND APPROVAL LIFESAVING EQUIPMENT Inflatable Lifejackets § 160.176-9 Construction. (a) General...

46 CFR 160.171-11 - Performance.

Science.gov (United States)

2010-10-01

... 46 Shipping 6 2010-10-01 2010-10-01 false Performance. 160.171-11 Section 160.171-11 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) EQUIPMENT, CONSTRUCTION, AND MATERIALS: SPECIFICATIONS AND APPROVAL LIFESAVING EQUIPMENT Immersion Suits § 160.171-11 Performance. (a) Buoyancy. Each...

46 CFR 160.176-11 - Performance.

Science.gov (United States)

2010-10-01

... 46 Shipping 6 2010-10-01 2010-10-01 false Performance. 160.176-11 Section 160.176-11 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) EQUIPMENT, CONSTRUCTION, AND MATERIALS: SPECIFICATIONS AND APPROVAL LIFESAVING EQUIPMENT Inflatable Lifejackets § 160.176-11 Performance. (a) General...

45 CFR 160.532 - Collateral estoppel.

Science.gov (United States)

2010-10-01

... 45 Public Welfare 1 2010-10-01 2010-10-01 false Collateral estoppel. 160.532 Section 160.532 Public Welfare DEPARTMENT OF HEALTH AND HUMAN SERVICES ADMINISTRATIVE DATA STANDARDS AND RELATED REQUIREMENTS GENERAL ADMINISTRATIVE REQUIREMENTS Procedures for Hearings § 160.532 Collateral estoppel. When a...

Tunable magnetostructural coupling and large magnetocaloric effect in Mn{sub 1−x}Ni{sub 1−x}Fe{sub 2x}Si{sub 1−x}Ga{sub x}

Energy Technology Data Exchange (ETDEWEB)

Zhang, C.L., E-mail: zhangcl@jiangnan.edu.cn [School of Science, Jiangnan University, WuXi 214122 (China); Nie, Y.G.; Shi, H.F.; Ye, E.J.; Zhao, J.Q. [School of Science, Jiangnan University, WuXi 214122 (China); Han, Z.D. [Jiangsu Laboratory of Advanced Functional Materials, Department of Physics, Changshu Institute of Technology, Changshu 215500 (China); Xuan, H.C. [College of Materials Science and Engineering, Taiyuan University of Technology, Taiyuan 030024 (China); Wang, D.H. [National Laboratory of Solid State Microstructures, Department of Physics, Nanjing University, Nanjing 210093 (China)

2017-06-15

Highlights: • Realizing FM/PM-type magnetostructural transition by co-substitution at both three atomic sites of MnNiSi. • Magnetostructural transition temperature is tunable in a broad temperature window of 285 K spanning room temperature. • Relatively high M{sub S} for the orthorhombic phase and large ΔM across the magnetostructural transition. • Relatively large magnetic entropy changes and broad working temperature span. - Abstract: A common method of realizing a magnetostructural coupling for MnNiSi is chemically alloying it with a ternary compound possessing a stable Ni{sub 2}In-type structure. In this way, the substituting elements and levels are determined by the stoichiometry of counterpart compounds. In this work, chemical co-substitutions of Fe and Ga at three different atomic sites of MnNiSi were performed. The selections of substitution elements and levels were based on the site occupation rule and an analysis of the site-dependent substitutional effects on structural stability, Curie temperatures, and magnetic moment of MnNiSi. A broad Curie temperatures window of 285 K spanning room temperature was established in Mn{sub 1−x}Ni{sub 1−x}Fe{sub 2x}Si{sub 1−x}Ga{sub x}. Strong magnetostructural transformations with large magnetization difference were realized in this window. A relatively large magnetic entropy change of −38.1 J/kg K was observed for a field change of 5 T near room temperature in the alloy with x = 0.15.

Provide Views | Efficient Windows Collaborative

Science.gov (United States)

Foundry Foundry New Construction Windows Window Selection Tool Selection Process Design Guidance Installation Replacement Windows Window Selection Tool Assessing Options Selection Process Design Guidance Installation Understanding Windows Benefits Design Considerations Measuring Performance Performance Standards

Reduced Fading | Efficient Windows Collaborative

Science.gov (United States)

Foundry Foundry New Construction Windows Window Selection Tool Selection Process Design Guidance Installation Replacement Windows Window Selection Tool Assessing Options Selection Process Design Guidance Installation Understanding Windows Benefits Design Considerations Measuring Performance Performance Standards

EWC Members | Efficient Windows Collaborative

Science.gov (United States)

Foundry Foundry New Construction Windows Window Selection Tool Selection Process Design Guidance Installation Replacement Windows Window Selection Tool Assessing Options Selection Process Design Guidance Installation Understanding Windows Benefits Design Considerations Measuring Performance Performance Standards

Visible Transmittance | Efficient Windows Collaborative

Science.gov (United States)

Foundry Foundry New Construction Windows Window Selection Tool Selection Process Design Guidance Installation Replacement Windows Window Selection Tool Assessing Options Selection Process Design Guidance Installation Understanding Windows Benefits Design Considerations Measuring Performance Performance Standards

Gas Fills | Efficient Windows Collaborative

Science.gov (United States)

Foundry Foundry New Construction Windows Window Selection Tool Selection Process Design Guidance Installation Replacement Windows Window Selection Tool Assessing Options Selection Process Design Guidance Installation Understanding Windows Benefits Design Considerations Measuring Performance Performance Standards

EWC Membership | Efficient Windows Collaborative

Science.gov (United States)

Foundry Foundry New Construction Windows Window Selection Tool Selection Process Design Guidance Installation Replacement Windows Window Selection Tool Assessing Options Selection Process Design Guidance Installation Understanding Windows Benefits Design Considerations Measuring Performance Performance Standards

Reducing Condensation | Efficient Windows Collaborative

Science.gov (United States)

Foundry Foundry New Construction Windows Window Selection Tool Selection Process Design Guidance Installation Replacement Windows Window Selection Tool Assessing Options Selection Process Design Guidance Installation Understanding Windows Benefits Design Considerations Measuring Performance Performance Standards

Improved Comfort | Efficient Windows Collaborative

Science.gov (United States)

Foundry Foundry New Construction Windows Window Selection Tool Selection Process Design Guidance Installation Replacement Windows Window Selection Tool Assessing Options Selection Process Design Guidance Installation Understanding Windows Benefits Design Considerations Measuring Performance Performance Standards

Financing & Incentives | Efficient Windows Collaborative

Science.gov (United States)

Foundry Foundry New Construction Windows Window Selection Tool Selection Process Design Guidance Installation Replacement Windows Window Selection Tool Assessing Options Selection Process Design Guidance Installation Understanding Windows Benefits Design Considerations Measuring Performance Performance Standards

Tools & Resources | Efficient Windows Collaborative

Science.gov (United States)

Foundry Foundry New Construction Windows Window Selection Tool Selection Process Design Guidance Installation Replacement Windows Window Selection Tool Assessing Options Selection Process Design Guidance Installation Understanding Windows Benefits Design Considerations Measuring Performance Performance Standards

Books & Publications | Efficient Windows Collaborative

Science.gov (United States)

Foundry Foundry New Construction Windows Window Selection Tool Selection Process Design Guidance Installation Replacement Windows Window Selection Tool Assessing Options Selection Process Design Guidance Installation Understanding Windows Benefits Design Considerations Measuring Performance Performance Standards

Design Considerations | Efficient Windows Collaborative

Science.gov (United States)

Foundry Foundry New Construction Windows Window Selection Tool Selection Process Design Guidance Installation Replacement Windows Window Selection Tool Assessing Options Selection Process Design Guidance Installation Understanding Windows Benefits Design Considerations Measuring Performance Performance Standards

Windows forensic analysis toolkit advanced analysis techniques for Windows 7

CERN Document Server

Carvey, Harlan

2012-01-01

Now in its third edition, Harlan Carvey has updated "Windows Forensic Analysis Toolkit" to cover Windows 7 systems. The primary focus of this edition is on analyzing Windows 7 systems and on processes using free and open-source tools. The book covers live response, file analysis, malware detection, timeline, and much more. The author presents real-life experiences from the trenches, making the material realistic and showing the why behind the how. New to this edition, the companion and toolkit materials are now hosted online. This material consists of electronic printable checklists, cheat sheets, free custom tools, and walk-through demos. This edition complements "Windows Forensic Analysis Toolkit, 2nd Edition", (ISBN: 9781597494229), which focuses primarily on XP. It includes complete coverage and examples on Windows 7 systems. It contains Lessons from the Field, Case Studies, and War Stories. It features companion online material, including electronic printable checklists, cheat sheets, free custom tools, ...

VISPA - Visual Physics Analysis on Linux, Mac OS X and Windows

International Nuclear Information System (INIS)

Brodski, M.; Erdmann, M.; Fischer, R.; Hinzmann, A.; Klimkovich, T.; Mueller, G.; Muenzer, T.; Steggemann, J.; Winchen, T.

2009-01-01

Modern physics analysis is an iterative task consisting of prototyping, executing and verifying the analysis procedure. For supporting scientists in each step of this process, we developed VISPA: a toolkit based on graphical and textual elements for visual physics analysis. Unlike many other analysis frameworks VISPA runs on Linux, Windows and Mac OS X. VISPA can be used in any experiment with serial data flow. In particular, VISPA can be connected to any high energy physics experiment. Furthermore, datatypes for the usage in astroparticle physics have recently been successfully included. An analysis on the data is performed in several steps, each represented by an individual module. While modules e.g. for file input and output are already provided, additional modules can be written by the user with C++ or the Python language. From individual modules, the analysis is designed by graphical connections representing the data flow. This modular concept assists the user in fast prototyping of the analysis and improves the reusability of written source code. The execution of the analysis can be performed directly from the GUI, or on any supported computer in batch mode. Therefore the analysis can be transported from the laptop to other machines. The recently improved GUI of VISPA is based on a plug-in mechanism. Besides components for the development and execution of physics analysis, additional plug-ins are available for the visualization of e.g. the structure of high energy physics events or the properties of cosmic rays in an astroparticle physics analysis. Furthermore plug-ins have been developed to display and edit configuration files of individual experiments from within the VISPA GUI. (author)

Advanced energy efficient windows

DEFF Research Database (Denmark)

Thomsen, Kirsten Engelund

2007-01-01

Windows should be paid special attention as they contribute a significant part of the total heat-loss coefficient of the building. Contrary to other parts of the thermal envelope the windows are not only heat loosers, but may gain heat in the day-time. Therefore there are possibilities for large...... energy savings. In terms of energy, windows occupy a special position compared with other thermal envelope structures due to their many functions: 1) windows let daylight into the building and provide occupants with visual contact with their surroundings 2) windows protect against the outdoor climate 3......) windows transmit solar energy that may contribute to a reduction of energy consumption, but which may also lead to unpleasant overheating. In the following paragraphs the current use of windows is reviewed with an emphasis on energy, while special products like solar protection glazing and security...

46 CFR 160.005-4 - Construction.

Science.gov (United States)

2010-10-01

... 46 Shipping 6 2010-10-01 2010-10-01 false Construction. 160.005-4 Section 160.005-4 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) EQUIPMENT, CONSTRUCTION, AND MATERIALS...), Models 52 and 56 § 160.005-4 Construction. (a) General. This specification covers life preservers which...

46 CFR 160.056-2 - Construction.

Science.gov (United States)

2010-10-01

... 46 Shipping 6 2010-10-01 2010-10-01 false Construction. 160.056-2 Section 160.056-2 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) EQUIPMENT, CONSTRUCTION, AND MATERIALS: SPECIFICATIONS AND APPROVAL LIFESAVING EQUIPMENT Rescue Boat § 160.056-2 Construction. (a) General. Rescue boats...

46 CFR 160.017-13 - Construction.

Science.gov (United States)

2010-10-01

... 46 Shipping 6 2010-10-01 2010-10-01 false Construction. 160.017-13 Section 160.017-13 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) EQUIPMENT, CONSTRUCTION, AND MATERIALS: SPECIFICATIONS AND APPROVAL LIFESAVING EQUIPMENT Chain Ladder § 160.017-13 Construction. (a) General. Each chain...

46 CFR 160.017-15 - Performance.

Science.gov (United States)

2010-10-01

... 46 Shipping 6 2010-10-01 2010-10-01 false Performance. 160.017-15 Section 160.017-15 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) EQUIPMENT, CONSTRUCTION, AND MATERIALS: SPECIFICATIONS AND APPROVAL LIFESAVING EQUIPMENT Chain Ladder § 160.017-15 Performance. (a) Each chain ladder...

Pharmacodynamics and tolerance of X-ray contrast media

International Nuclear Information System (INIS)

Schmiedel, E.

1987-01-01

The improved tolerance of nonionic contrast media compared with conventional contrast media is mainly due to their lower osmolality and reduced allergoid potential. Tolerance advantages that have been definitely proven are, for example, low-pain contrast medium injection and superior systemic tolerance; side effects of an allergic pattern occur less often. Animals experiments have established that nonionic contrast media exercise a comparatively lower influence on the cardiovascular system. The haemodynamics of pulmonary circulation are less adversely affected on intravenous bolus injection. Reduced potential risk is to be expected especially in cardiac and bronchopulmonary high-risk patients. The reduced nephrotoxicity of nonionic contrast media was definitely established by clinical studies. Further systematic studies will however be required to provide an answer to the question whether this also entails a reduction in the incidence of renal failures induced by contrast media. (orig.) [de

Windows 8 secrets

CERN Document Server

Thurrott, Paul

2012-01-01

Tips, tricks, treats, and secrets revealed on Windows 8 Microsoft is introducing a major new release of its Windows operating system, Windows 8, and what better way to learn all its ins and outs than from two internationally recognized Windows experts and Microsoft insiders, authors Paul Thurrott and Rafael Rivera? They cut through the hype to get at useful information you'll not find anywhere else, including what role this new OS plays in a mobile and tablet world. Regardless of your level of knowledge, you'll discover little-known facts about how things work, what's new and different, and h

Programming Windows Azure

CERN Document Server

Krishnan, Sriram

2010-01-01

Learn the nuts and bolts of cloud computing with Windows Azure, Microsoft's new Internet services platform. Written by a key member of the product development team, this book shows you how to build, deploy, host, and manage applications using Windows Azure's programming model and essential storage services. Chapters in Programming Windows Azure are organized to reflect the platform's buffet of services. The book's first half focuses on how to write and host application code on Windows Azure, while the second half explains all of the options you have for storing and accessing data on the plat

Beginning Windows 8

CERN Document Server

Halsey, Mike

2012-01-01

Windows 8 has been described by Microsoft as its 'boldest' Windows release ever. Beginning Windows 8 takes you through the new features and helps you get more out of the familiar to reveal the possibilities for this amazing new operating system. You will learn, with non-technical language used throughout, how to get up and running in the new Windows interface, minimize downtime, maximize productivity, and harness the features you never knew existed to take control of your computer and enjoy the peace of mind and excitement that comes with it. From tips and tweaks to easy-to-follow guides and d

12 CFR 560.160 - Asset classification.

Science.gov (United States)

2010-01-01

... 12 Banks and Banking 5 2010-01-01 2010-01-01 false Asset classification. 560.160 Section 560.160... Lending and Investment Provisions Applicable to all Savings Associations § 560.160 Asset classification... consistent with, or reconcilable to, the asset classification system used by OTS in its Thrift Activities...

40 CFR 160.61 - Equipment design.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 23 2010-07-01 2010-07-01 false Equipment design. 160.61 Section 160... LABORATORY PRACTICE STANDARDS Equipment § 160.61 Equipment design. Equipment used in the generation... appropriate design and adequate capacity to function according to the protocol and shall be suitably located...

21 CFR 173.160 - Candida guilliermondii.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Candida guilliermondii. 173.160 Section 173.160... CONSUMPTION Enzyme Preparations and Microorganisms § 173.160 Candida guilliermondii. The food additive Candida... the following conditions: (a) The food additive is the enzyme system of the viable organism Candida...

46 CFR 160.026-3 - Container.

Science.gov (United States)

2010-10-01

... 46 Shipping 6 2010-10-01 2010-10-01 false Container. 160.026-3 Section 160.026-3 Shipping COAST...: SPECIFICATIONS AND APPROVAL LIFESAVING EQUIPMENT Water, Emergency Drinking (In Hermetically Sealed Containers), for Merchant Vessels § 160.026-3 Container. (a) General. The emergency drinking water container shall...

Comparison of [18F]FLT and [18F]FDG in in vitro cancer cell uptake and glucose effect

International Nuclear Information System (INIS)

Soo Jung Lim; Jin-Sook Ryu; Heuiran Lee; Seok Young Kim; Seung Jun Oh; Dae Hyuk Moon

2004-01-01

[18F]FLT is a new radiopharmaceutical for cell proliferation. We compared [18F]FLT and [18F]FDG in in vitro cancer cell uptake and glucose effect. Method: In vitro cancer cell uptake of [18F]FLT was evaluated using SCC7(mouse squamous cell carcinoma). At 24 hours after seeding 1 x 106 cells/well in 6 well plates with RPMI 1640 medium, culture media were changed to medium with glucose free or glucose concentration of 100 mg/dl. Then, [18F]FLT 5 μCi/50 ml was added to each well. After incubation for 30, 60, 90, 120 minutes, cells were washed twice by PBS, and harvested using 0.25% trypsin-EDTA. After centrifugation and counting at gamma counter, cell uptake was calculated by % activity of cellular uptake to total activity of cell and supernatant. For comparison, same tumor cell uptake experiment was performed with [18F]FDG. Results: After incubation with SCC7 cell line for 30, 60, 90, 120 minutes, [18F]FLT showed 1.95%, 2.17%, 2.10% and 2.80% of cell uptake in glucose free media, respectively. The results [18F]FLT uptake in glucose 100 mg/dl media were 1.82%, 1.87%, 1.97%, and 2.94%, respectively. The results of [18F]FDG in glucose free media were 2.50%, 3.47%, 5.04%, and 10.4%, whereas those in glucose 100 mg/dl media were 1.60%, 1.79%, 1.53%, and 1.82%, respectively. Conclusion: In contrast to [18F]FDG, [18F]FLT uptake in cancer cell was not affected by glucose concentration. In physiologic glucose concentration, [18F]FLT uptake in SCC7 cell line was significantly higher than [18F]FDG uptake after 120 minutes incubation. In [18F]FLT PET imaging may not need fasting for preparation before imaging study. (authors)

Transthoracic Doppler echocardiography to predict optimal tube pulsing window for coronary artery CT angiography

Energy Technology Data Exchange (ETDEWEB)

Sun, Gang, E-mail: cjr.sungang@vip.163.com [Department of Medical Imaging, Jinan Military General Hospital, No. 25, Shifan Road, Jinan, Shandong Province 250031 (China); Li, Min, E-mail: limin22000@yahoo.com.cn [Department of Medical Imaging, Jinan Military General Hospital, No. 25, Shifan Road, Jinan, Shandong Province 250031 (China); Jiang, Xiang-sen, E-mail: jiangxiangsen123@126.com [Department of Medical Imaging, Jinan Military General Hospital, No. 25, Shifan Road, Jinan, Shandong Province 250031 (China); Li, Li, E-mail: leely1976@yahoo.com.cn [Department of Medical Imaging, Jinan Military General Hospital, No. 25, Shifan Road, Jinan, Shandong Province 250031 (China); Peng, Zhao-hui, E-mail: zhaohuipeng_R@163.com [Department of Medical Imaging, Jinan Military General Hospital, No. 25, Shifan Road, Jinan, Shandong Province 250031 (China); Mu, Nan-nan, E-mail: munannan22000@sohu.com [Department of Medical Imaging, Jinan Military General Hospital, No. 25, Shifan Road, Jinan, Shandong Province 250031 (China)

2012-09-15

Rationale and objective: To evaluate the feasibility of transthoracic Doppler echocardiography to determine the optimal pulsing windows for CT coronary angiography to narrow the pulsing windows further, especially in higher heart rate. Materials and methods: Doppler was performed on 135 patients before CT scanning. For Doppler, the intervals with minimal motion were evaluated during both systole and diastole integrating electrocardiogram (ECG) intervals. For CT scanning, the retrospective ECG-gating was applied and the optimal reconstruction intervals were determined. The accuracy of Doppler analysis to predict the optimal reconstruction intervals was tested. The predicted length of pulsing windows was compared between Doppler analysis and traditional prospective ECG-gating protocol (heart rate ≦ 65 bpm, 60–76%; 66–79 bpm, 30–77%; ≧80 bpm, 31–47%). Results: According to Doppler analysis, the mean length of intervals with minimal motion in systole was 106.4 ± 39.2 ms and 125.2 ± 92.0 ms in diastole. When the intervals with minimal motion during diastole > 90 ms, the optimal reconstruction intervals were located at diastole; otherwise, at systole (P < 0.001). The optimal reconstruction intervals in 93.8% (132/135) patients could be predicted accurately by Doppler analysis. If the optimal reconstruction intervals predicted by Doppler were applied as the exposure windows, the mean length of pulsing windows should has been 105.2 ± 69.4 ms (range: 26.9–510.3 ms), which was significantly shorter than that of traditional prospective ECG-gating protocol (232.0 ± 120.2 ms, range: 93.2–427.3 ms, P < 0.001). Conclusion: Doppler can help detecting the optimal pulsing windows accurately. Prospective ECG-gating incorporating Doppler analysis may narrow pulsing windows significantly while maintaining image quality.

Transthoracic Doppler echocardiography to predict optimal tube pulsing window for coronary artery CT angiography

International Nuclear Information System (INIS)

Sun, Gang; Li, Min; Jiang, Xiang-sen; Li, Li; Peng, Zhao-hui; Mu, Nan-nan

2012-01-01

Rationale and objective: To evaluate the feasibility of transthoracic Doppler echocardiography to determine the optimal pulsing windows for CT coronary angiography to narrow the pulsing windows further, especially in higher heart rate. Materials and methods: Doppler was performed on 135 patients before CT scanning. For Doppler, the intervals with minimal motion were evaluated during both systole and diastole integrating electrocardiogram (ECG) intervals. For CT scanning, the retrospective ECG-gating was applied and the optimal reconstruction intervals were determined. The accuracy of Doppler analysis to predict the optimal reconstruction intervals was tested. The predicted length of pulsing windows was compared between Doppler analysis and traditional prospective ECG-gating protocol (heart rate ≦ 65 bpm, 60–76%; 66–79 bpm, 30–77%; ≧80 bpm, 31–47%). Results: According to Doppler analysis, the mean length of intervals with minimal motion in systole was 106.4 ± 39.2 ms and 125.2 ± 92.0 ms in diastole. When the intervals with minimal motion during diastole > 90 ms, the optimal reconstruction intervals were located at diastole; otherwise, at systole (P < 0.001). The optimal reconstruction intervals in 93.8% (132/135) patients could be predicted accurately by Doppler analysis. If the optimal reconstruction intervals predicted by Doppler were applied as the exposure windows, the mean length of pulsing windows should has been 105.2 ± 69.4 ms (range: 26.9–510.3 ms), which was significantly shorter than that of traditional prospective ECG-gating protocol (232.0 ± 120.2 ms, range: 93.2–427.3 ms, P < 0.001). Conclusion: Doppler can help detecting the optimal pulsing windows accurately. Prospective ECG-gating incorporating Doppler analysis may narrow pulsing windows significantly while maintaining image quality

High Pressure In Situ X-ray Diffraction Study of MnO to 120 GPa and Comparison with Shock Compression Experiment

Science.gov (United States)

Yagi, Takehiko; Kondo, Tadashi; Syono, Yasuhiko

1997-07-01

In order to clarify the nature of the phase transformation in MnO observed at around 90 GPa by shock compression experiment (Syono et al., this symposium), high pressure in situ x-ray experiments were carried out up to 120 GPa. Powdered sample was directly compressed in Mao-Bell type diamond anvil and x-ray experiments were carried out using angle dispersive technique by combining synchrotron radiation and imaging plate detector. Distortion of the B1 structured phase into hexagonal unit cell was observed from 25-40 GPa, which continues to increase up to 90 GPa. At around 90 GPa, discontinuous change of the diffraction was observed. This new phase cannot be explained by a simple B2 structure and the analysis of this phase is in progress. This high pressure phase has metallic appearance, which reverses to transparent MnO on release of pressure.

7 CFR 160.32 - Marking containers.

Science.gov (United States)

2010-01-01

... 7 Agriculture 3 2010-01-01 2010-01-01 false Marking containers. 160.32 Section 160.32 Agriculture... STANDARDS FOR NAVAL STORES Analysis, Inspection, and Grading on Request § 160.32 Marking containers. The interested person shall provide any labor necessary for marking the containers, after the contents have been...

7 CFR 160.89 - Medicinal preparations.

Science.gov (United States)

2010-01-01

... 7 Agriculture 3 2010-01-01 2010-01-01 false Medicinal preparations. 160.89 Section 160.89... STANDARDS FOR NAVAL STORES Sales and Shipments § 160.89 Medicinal preparations. A compound or mixture containing spirits of turpentine or rosin, or both, with other drugs, when sold for medicinal purposes, is...

Levels and transitions in 160Dy following the decay of 160Tb

International Nuclear Information System (INIS)

Noordin bin Ibrahim; Stewart, N.M.

1989-01-01

The level scheme of 160 Dy has been established from γ-γ coincidence measurement following the β-decay of 160 Tb. Ge(Li) detectors were coupled to a Dual Parameter Spectrometer for data collection. A total of fifteen new gamma transitions were observed. Two energy levels at 1285 and 1288 keV were confirmed while four levels at 1349, 1670, 1694 and 1804 keV were found to be populated for the first time from β-decay of 160 Tb: Three levels at 1230, 1338 and 1507 keV are newly suggested. Relative intensities for the transitions and branching ratios of the energy levels were determined. Comparisons are made with theoretical predictions of IBA calculations, two considerations were taken: normal shell closure (Z 50/82) and subshell closure (Z = 64). (author)

An Evaluation of Windows-Based Computer Forensics Application Software Running on a Macintosh

Directory of Open Access Journals (Sweden)

Gregory H. Carlton

2008-09-01

Full Text Available The two most common computer forensics applications perform exclusively on Microsoft Windows Operating Systems, yet contemporary computer forensics examinations frequently encounter one or more of the three most common operating system environments, namely Windows, OS-X, or some form of UNIX or Linux. Additionally, government and private computer forensics laboratories frequently encounter budget constraints that limit their access to computer hardware. Currently, Macintosh computer systems are marketed with the ability to accommodate these three common operating system environments, including Windows XP in native and virtual environments. We performed a series of experiments to measure the functionality and performance of the two most commonly used Windows-based computer forensics applications on a Macintosh running Windows XP in native mode and in two virtual environments relative to a similarly configured Dell personal computer. The research results are directly beneficial to practitioners, and the process illustrates affective pedagogy whereby students were engaged in applied research.

Representation and Dissemination of Intangible Cultural Heritage of Bangladesh through Social Media

DEFF Research Database (Denmark)

Khalid, Md. Saifuddin; Chowdhury, Md Saiful Alam

2016-01-01

Bangladesh is one of the next eleven countries and home to more than 160 million people. The country is experiencing an exponential growth of social media users due to the increase in affordability of smartphones, literacy rate, education level, and adoption of Internet services and applications...... of strategically representing and diffusing ICH through social media, this research explores the current roles of social media in the transmission of ICH in the virtual world. The research question is: How are Baul song and Jamdani weaving as intangible cultural heritage of Bangladesh represented and disseminated...... through social media platforms?...

46 CFR 160.026-4 - Water.

Science.gov (United States)

2010-10-01

... 46 Shipping 6 2010-10-01 2010-10-01 false Water. 160.026-4 Section 160.026-4 Shipping COAST GUARD... APPROVAL LIFESAVING EQUIPMENT Water, Emergency Drinking (In Hermetically Sealed Containers), for Merchant Vessels § 160.026-4 Water. (a) Only water meeting the U.S. Public Health Service “Drinking Water Standards...

Investigations of corrosion films formed on API-X52 pipeline steel in acid sour media

Energy Technology Data Exchange (ETDEWEB)

Hernandez-Espejel, A. [Instituto Politecnico Nacional, Departamento de Ingenieria Metalurgica, IPN-ESIQIE, UPALM Ed. 7, Zacatenco 07738, Mexico, D.F. (Mexico); Dominguez-Crespo, M.A. [Instituto Politecnico Nacional, CICATA-Unidad Altamira-Tamaulipas, km 14.5, Carretera Tampico-Puerto Industrial Altamira, 89600 Altamira, Tamps (Mexico); Cabrera-Sierra, R. [Instituto Politecnico Nacional, Departamento de Ingenieria Quimica Industrial, IPN-ESIQIE, UPALM Ed. 7, Zacatenco 07738, Mexico, D.F. (Mexico); Rodriguez-Meneses, C. [Instituto Politecnico Nacional, Departamento de Ingenieria Metalurgica, IPN-ESIQIE, UPALM Ed. 7, Zacatenco 07738, Mexico, D.F. (Mexico); Arce-Estrada, E.M., E-mail: earce@ipn.m [Instituto Politecnico Nacional, Departamento de Ingenieria Metalurgica, IPN-ESIQIE, UPALM Ed. 7, Zacatenco 07738, Mexico, D.F. (Mexico)

2010-07-15

Corrosion films formed by voltammetry using different switching potentials and by immersion on API-X52 pipeline steel in simulated acid sour media (NACE ID182) have been characterized using Scanning Electron Microscopy (SEM), X-ray Diffraction (XRD), Linear Polarization and Electrochemical Impedance Spectroscopy (EIS) techniques. XRD and EDS analysis showed that the films are mainly composed of sulphide compounds (mackinawite, troilite, marcasite and pyrite) as well as iron oxides, as steel damage increases. Across SEM micrographs the corrosion films formed by potentiodynamic and immersion tests are very similar, covering most of the steel. Polarization and EIS results corroborate poor behavior against corrosion.

Investigations of corrosion films formed on API-X52 pipeline steel in acid sour media

International Nuclear Information System (INIS)

Hernandez-Espejel, A.; Dominguez-Crespo, M.A.; Cabrera-Sierra, R.; Rodriguez-Meneses, C.; Arce-Estrada, E.M.

2010-01-01

Corrosion films formed by voltammetry using different switching potentials and by immersion on API-X52 pipeline steel in simulated acid sour media (NACE ID182) have been characterized using Scanning Electron Microscopy (SEM), X-ray Diffraction (XRD), Linear Polarization and Electrochemical Impedance Spectroscopy (EIS) techniques. XRD and EDS analysis showed that the films are mainly composed of sulphide compounds (mackinawite, troilite, marcasite and pyrite) as well as iron oxides, as steel damage increases. Across SEM micrographs the corrosion films formed by potentiodynamic and immersion tests are very similar, covering most of the steel. Polarization and EIS results corroborate poor behavior against corrosion.

Window selection for dual photopeak window scatter correction in Tc-99m imaging

International Nuclear Information System (INIS)

Vries, D.J. de; King, M.A.

1994-01-01

The width and placement of the windows for the dual photopeak window (DPW) scatter subtraction method for Tc-99m imaging is investigated in order to obtain a method that is stable on a multihead detector system for single photon emission computed tomography (SPECT) and is capable of providing a good scatter estimate for extended objects. For various window pairs, stability and noise were examined with experiments using a SPECT system, while Monte Carlo simulations were used to predict the accuracy of scatter estimates for a variety of objects and to guide the development of regression relations for various window pairs. The DPW method that resulted from this study was implemented with a symmetric 20% photopeak window composed of a 15% asymmetric photopeak window and a 5% lower window abutted at 7 keV below the peak. A power function regression was used to relate the scatter-to-total ratio to the lower window-to-total ratio at each pixel, from which an estimated scatter image was calculated. DPW demonstrated good stability, achieved by abutting the two windows away from the peak. Performance was assessed and compared with Compton window subtraction (CWS). For simulated extended objects, DPW generally produced a less biased scatter estimate than the commonly used CWS method with k = 0.5. In acquisitions of a clinical SPECT phantom, contrast recovery was comparable for both DPW and CWS; however, DPW showed greater visual contrast in clinical SPECT bone studies

21 CFR 172.160 - Potassium nitrate.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Potassium nitrate. 172.160 Section 172.160 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR HUMAN... Preservatives § 172.160 Potassium nitrate. The food additive potassium nitrate may be safely used as a curing...

21 CFR 160.115 - Liquid eggs.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 2 2010-04-01 2010-04-01 false Liquid eggs. 160.115 Section 160.115 Food and... CONSUMPTION EGGS AND EGG PRODUCTS Requirements for Specific Standardized Eggs and Egg Products § 160.115 Liquid eggs. (a) Liquid eggs, mixed eggs, liquid whole eggs, mixed whole eggs are eggs of the domestic...

46 CFR 160.037-6 - Container.

Science.gov (United States)

2010-10-01

... 46 Shipping 6 2010-10-01 2010-10-01 false Container. 160.037-6 Section 160.037-6 Shipping COAST...: SPECIFICATIONS AND APPROVAL LIFESAVING EQUIPMENT Hand Orange Smoke Distress Signals § 160.037-6 Container. (a) General. The container for storing the signals on lifeboats and liferafts is not required to be of a...

Study of Various Processes with 160 A GeV Pb Beam

CERN Multimedia

2002-01-01

% WA101 \\\\ \\\\ Ten modules of BP-1 glass detectors interleaved with various targets ranging from C to Pb were exposed to the 160~A~GeV~Pb beam in the November-December run of 1994 at CERN SPS. The experiment was carried out at normal incidence at a beam density of $\\sim$~600~cm$ ^- ^{2} $. The dimension of each plate of BP-1 glass was 50~mm~x~50~mm~x~1~mm. We etched the glass in 70\\% CH$ _{3} $SO$ _{3} $H at 50 $^{0}$C or in 48\\%~HF at room temperature. The charge threshold is found to be Z$ _{t} _{h} $ $\\sim$ 68 and 70 respectively. Using the automated scanning and measurement system developed at Berkeley, we have demonstrated that the charge resolution for Pb ions is $\\sigma _{Z} $~=~0.14 charge unit from a single measurement within a distance of 30~$\\mu$m. This excellent charge resolution allows us to make the proposed measurements of cross-sections for various processes. \\\\ \\\\We use this detector system to measure cross-sections for various processes in heavy ion collisions of 160~A~GeV~Pb with different t...

21 CFR 160.180 - Egg yolks.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 2 2010-04-01 2010-04-01 false Egg yolks. 160.180 Section 160.180 Food and Drugs... CONSUMPTION EGGS AND EGG PRODUCTS Requirements for Specific Standardized Eggs and Egg Products § 160.180 Egg yolks. (a) Egg yolks, liquid egg yolks, yolks, liquid yolks are yolks of eggs of the domestic hen so...

46 CFR 160.036-6 - Container.

Science.gov (United States)

2010-10-01

... 46 Shipping 6 2010-10-01 2010-10-01 false Container. 160.036-6 Section 160.036-6 Shipping COAST... § 160.036-6 Container. (a) General. The container for storing the signals on lifeboats and liferafts is not required to be of a special design or be approved by the Coast Guard. The container must meet the...

46 CFR 160.174-11 - Performance.

Science.gov (United States)

2010-10-01

... 46 Shipping 6 2010-10-01 2010-10-01 false Performance. 160.174-11 Section 160.174-11 Shipping...: SPECIFICATIONS AND APPROVAL LIFESAVING EQUIPMENT Thermal Protective Aids § 160.174-11 Performance. (a) Thermal... between −30 °C (−22 °F) and +65 C (149 °F). (d) In water performance. The thermal protective aid must be...

21 CFR 135.160 - Water ices.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 2 2010-04-01 2010-04-01 false Water ices. 135.160 Section 135.160 Food and Drugs... CONSUMPTION FROZEN DESSERTS Requirements for Specific Standardized Frozen Desserts § 135.160 Water ices. (a) Description. Water ices are the foods each of which is prepared from the same ingredients and in the same...

Recording performances in perpendicular magnetic patterned media

International Nuclear Information System (INIS)

Asbahi, M; Moritz, J; Dieny, B; Gourgon, C; Perret, C; Van de Veerdonk, R J M

2010-01-01

We report on the recording performances and signal-to-noise ratio (SNR) analyses of perpendicular magnetic bit-patterned media. Two different types of magnetic samples are investigated. They differ by the way that they were patterned (nano-imprint versus e-beam lithography) as well as their magnetic properties (Co/Pt multilayers and CoCrPt alloy are the recording layers).Using a contact read/write quasi-static tester, we were able to characterize the write windows, the bit error rates and measure the SNR. The influence of magnetic properties and media microstructure on the writing processes is studied. We show also that the lithographical method used to replicate the media induces more or less noise due to structural distributions.

A JEM-X catalog of X-ray sources

DEFF Research Database (Denmark)

Westergaard, Niels Jørgen Stenfeldt; Chenevez, Jerome; Lund, Niels

2007-01-01

The JEM-X catalog of X-ray sources presented here is based on detections in individual science windows with a sensitivity limit of about 10 mCrab (5-15 keV). It contains 127 sources and only those that can be identified from the existing reference catalog. The input data are taken from the, up...

36 CFR 909.160 - Communications.

Science.gov (United States)

2010-07-01

... Section 909.160 Parks, Forests, and Public Property PENNSYLVANIA AVENUE DEVELOPMENT CORPORATION... PENNSYLVANIA AVENUE DEVELOPMENT CORPORATION § 909.160 Communications. (a) The agency shall take appropriate... telephone, telecommunication devices for deaf person (TDD's) or equally effective telecommunication systems...

A System for Multimodal Interaction with Kinect-Enabled Virtual Windows

Directory of Open Access Journals (Sweden)

Ana M. Bernardos

2015-11-01

Full Text Available Commercial off-the-shelf gaming devices (e.g. such as Kinect are demonstrating to have a great potential beyond their initial service purpose. In particular, when integrated within the environment or as part of smart objects, peripheral COTS for gaming may facilitate the definition of novel interaction methods, particularly applicable to smart spaces service concepts. In this direction, this paper describes a system prototype that makes possible to deliver multimodal interaction with the media contents in a Virtual Window. Using a Kinect device, the Interactive Window itself adjusts the video clipping to the real time perspective of the user – who can freely move within the sensor coverage are. On the clipped video, the user is able to select objects by pointing at meaningful image sections and to initiate actions related to them. Voice orders may also complete the interaction when necessary. Although implemented for smart spaces, the service concept can also be applied to learning, remote control processes or teleconference.

An enhanced geometry-independent mesh weight window generator for MCNP

International Nuclear Information System (INIS)

Evans, T.M.; Hendricks, J.S.

1997-01-01

A new, enhanced, weight window generator suite has been developed for MCNP trademark. The new generator correctly estimates importances in either an user-specified, geometry-independent orthogonal grid or in MCNP geometric cells. The geometry-independent option alleviates the need to subdivide the MCNP cell geometry for variance reduction purposes. In addition, the new suite corrects several pathologies in the existing MCNP weight window generator. To verify the correctness of the new implementation, comparisons are performed with the analytical solution for the cell importance. Using the new generator, differences between Monte Carlo generated and analytical importances are less than 0.1%. Also, assumptions implicit in the original MCNP generator are shown to be poor in problems with high scattering media. The new generator is fully compatible with MCNP's AVATAR trademark automatic variance reduction method. The new generator applications, together with AVATAR, gives MCNP an enhanced suite of variance reduction methods. The flexibility and efficacy of this suite is demonstrated in a neutron porosity tool well-logging problem

Determination of the optimal tolerance for MLC positioning in sliding window and VMAT techniques

International Nuclear Information System (INIS)

Hernandez, V.; Abella, R.; Calvo, J. F.; Jurado-Bruggemann, D.; Sancho, I.; Carrasco, P.

2015-01-01

Purpose: Several authors have recommended a 2 mm tolerance for multileaf collimator (MLC) positioning in sliding window treatments. In volumetric modulated arc therapy (VMAT) treatments, however, the optimal tolerance for MLC positioning remains unknown. In this paper, the authors present the results of a multicenter study to determine the optimal tolerance for both techniques. Methods: The procedure used is based on dynalog file analysis. The study was carried out using seven Varian linear accelerators from five different centers. Dynalogs were collected from over 100 000 clinical treatments and in-house software was used to compute the number of tolerance faults as a function of the user-defined tolerance. Thus, the optimal value for this tolerance, defined as the lowest achievable value, was investigated. Results: Dynalog files accurately predict the number of tolerance faults as a function of the tolerance value, especially for low fault incidences. All MLCs behaved similarly and the Millennium120 and the HD120 models yielded comparable results. In sliding window techniques, the number of beams with an incidence of hold-offs >1% rapidly decreases for a tolerance of 1.5 mm. In VMAT techniques, the number of tolerance faults sharply drops for tolerances around 2 mm. For a tolerance of 2.5 mm, less than 0.1% of the VMAT arcs presented tolerance faults. Conclusions: Dynalog analysis provides a feasible method for investigating the optimal tolerance for MLC positioning in dynamic fields. In sliding window treatments, the tolerance of 2 mm was found to be adequate, although it can be reduced to 1.5 mm. In VMAT treatments, the typically used 5 mm tolerance is excessively high. Instead, a tolerance of 2.5 mm is recommended

John Adams Lecture | 120 Years of Accelerators that Heal | 3 December

CERN Multimedia

2013-01-01

120 Years of Accelerators that Heal, Dr Ugo Amaldi, Technische Universität München and TERA Foundation.     Tuesday 3 December 2013 at 2 p.m. Kjell Johnsen Auditorium, Building 30 Abstract: The discovery of X-rays was made possible by the intelligent use of the best accelerator of the time. Since then, the development of particle accelerators has been at the root of both fundamental discoveries in physics and unforeseeable medical applications. The lecture will describe the major steps in this 120-year history of diagnostics and tumour therapy. The first attempts to heal tumours with X-rays were made only one month after Röntgen’s discovery, but the understanding of the mechanisms by which the radiation kills the cells and the introduction of dose fractionation took much longer. The use of X-rays in diagnostics developed much faster and its benefits were very visible during the First World War. Today no tumour could be treated and no patient could be oper...

Characterization of Beryllium Windows for Coherent X-ray Optics

International Nuclear Information System (INIS)

Goto, Shunji; Yabashi, Makina; Tamasaku, Kenji; Ishikawa, Tetsuya

2007-01-01

Beryllium foils fabricated by several processes were characterized using spatially coherent x rays at 1-km beamline of SPring-8. By thickness dependence of bright x-ray spot density due to Fresnel diffraction from several-micron deficiencies, we found that speckles (bright x-ray spots) were due to voids with densities 103-104 mm-3 in powder foils and ingot foils. Compared with powder and ingot foils, a polished physical-vapor-deposited (PVD) beryllium foil gave highly uniform beams with no speckles. The PVD process eliminates the internal voids in principle and the PVD foil is the best for coherent x-ray applications

Students as Producers: An "X" Disciplinary Client-Based Approach to Collaborative Art, Design and Media Pedagogy

Science.gov (United States)

Cocchiarella, Fabrizio; Booth, Paul

2015-01-01

This article presents the findings of a cross-disciplinary project between BA (Hons) Interior Design, Creative Multimedia and Film and Media Studies at a large Metropolitan University in the North of England. The collaboration was part of Unit X, a faculty-wide credit-bearing initiative to enable better collaboration across art and design courses.…

Windows XP ends its life at CERN – register for Windows 7 training!

CERN Multimedia

Michał Kwiatek (IT-OIS)

2012-01-01

Windows XP has been around for over 10 years and it is now time to move on. At CERN, general support for Windows XP will end in December 2012, and before this date users are requested to schedule a migration to the next version of Windows – Windows 7.   Windows 7 is already well established at CERN – it is used by a large majority of users. In fact, there was a considerable user demand even before its official release in October 2009 and its adoption has been smooth. Users praise Windows 7 for its improved stability and a clear advantage on laptops is a much more efficient implementation of offline files. The migration to Windows 7 involves a reinstallation of the operating system. Files stored in user home folders on DFS will be immediately available after the reinstallation. Applications will be upgraded to more recent versions and in certain cases, an application may even be replaced by another application providing the same functionality. Microsoft Office suite is a good ...

Thermal bridges of modern windows

DEFF Research Database (Denmark)

Hansen, Ernst Jan de Place; Møller, Eva B.; Nielsen, Anker

2013-01-01

if the window has an U-factor of 1 W/(m2·K) or lower. This paper describes the development of modern, energy efficient Danish windows with reduced thermal bridges. It focuses on materials, geometry, and sealing of window panes based on a literature review. Examples of modern windows are presented. Experience...... been an important driver for the development of new window solutions in Denmark, increasing the inner-surface temperature at the sealing of window panes. However, it will not stop complaints fromconsumers, as this temperature is calculated under standardized conditions. Increasing requirements...

The beam steering system of the cyclotron U-120K; Sistema razvodki puchkov tsiklotrona U-120K

Energy Technology Data Exchange (ETDEWEB)

Borkova, A; Ivan, J; Trejbal, Z; Dmitrievskij, V P; Pavlov, D V; Chesnov, A F; Chesnova, S I

1991-12-31

The calculation of the beam transport system of the isochronous cyclotron U-120K is presented. This system realizes the beam transport with given parameters to six distant targets specializing in the production of radioactive isotopes, the biomedicine investigation, the experimental nuclear physics. At chosen parameters of lenses and bending magnets the beam size is {<=} 1x1 cm and the energy resolution in the monoenergetic line is less than 0.1%. 4 refs.; 6 figs.; 1 tab.

Drugs + HIV, Learn the Link

Medline Plus

Full Text Available ... at: http://www.drugabuse.gov/news-events/public-education-projects/learn-link-drugs-hiv . 120x90 460x80 486x60 Social Media Send the message to young people and to parents, teachers, and the media ...

Fluorometric sensing of Triton X-100 based organized media in water by a MOF

Energy Technology Data Exchange (ETDEWEB)

Dey, Biswajit, E-mail: bdeychem@gmail.com [Department of Chemistry, Visva-Bharati University, Santiniketan 731235 (India); Mondal, Ranjan Kumar; Dhibar, Subhendu [Department of Chemistry, Visva-Bharati University, Santiniketan 731235 (India); Chattopadhyay, Asoke Prasun [Department of Chemistry, University of Kalyani, Kalyani 741235 (India); Bhattacharya, Subhash Chandra [Department of Chemistry, Jadavpur University, Kolkata 700032 (India)

2016-04-15

The fluorescent property of the aqueous solution of a metal organic framework (MOF) of Mn(II), having a sedimentary rocks like microstructure in solid-state, has been investigated. The luminescent feature of the the aqueous solution of MOF has been employed for studying the interactions of MOF with different surfactants including neutral, cationic, and anionic types in water medium. Interestingly, the MOF can very selective sense Triton X-100 based micelle in water medium. During the sensing process the fluorescent monomer of the MOF gets accommodated at the palisade layer of Triton X-100 in water medium and this has also been justified by simple fluorescence spectral and FE-SEM microstructural analysis. Thus, a MOF of Mn(II) can act as a selective fluorescent sensor for Triton X-100 based organized medium in water. - Highlights: • Microstructural and crystallographic studies of a water-soluble MOF are performed. • The luminescent property of MOF in water medium is explored. • The interaction between Triton X-100 and the MOF in water medium is studied by fluorometric and microstructural analysis. • The MOF acts as a selective fluorometric sensor for the Triton X-100 based organized media in water. • The monomer of MOF presents in the Triton X-100 micelle in water.

Fluorometric sensing of Triton X-100 based organized media in water by a MOF

International Nuclear Information System (INIS)

Dey, Biswajit; Mondal, Ranjan Kumar; Dhibar, Subhendu; Chattopadhyay, Asoke Prasun; Bhattacharya, Subhash Chandra

2016-01-01

The fluorescent property of the aqueous solution of a metal organic framework (MOF) of Mn(II), having a sedimentary rocks like microstructure in solid-state, has been investigated. The luminescent feature of the the aqueous solution of MOF has been employed for studying the interactions of MOF with different surfactants including neutral, cationic, and anionic types in water medium. Interestingly, the MOF can very selective sense Triton X-100 based micelle in water medium. During the sensing process the fluorescent monomer of the MOF gets accommodated at the palisade layer of Triton X-100 in water medium and this has also been justified by simple fluorescence spectral and FE-SEM microstructural analysis. Thus, a MOF of Mn(II) can act as a selective fluorescent sensor for Triton X-100 based organized medium in water. - Highlights: • Microstructural and crystallographic studies of a water-soluble MOF are performed. • The luminescent property of MOF in water medium is explored. • The interaction between Triton X-100 and the MOF in water medium is studied by fluorometric and microstructural analysis. • The MOF acts as a selective fluorometric sensor for the Triton X-100 based organized media in water. • The monomer of MOF presents in the Triton X-100 micelle in water.

7 CFR 925.160 - Reports.

Science.gov (United States)

2010-01-01

... 7 Agriculture 8 2010-01-01 2010-01-01 false Reports. 925.160 Section 925.160 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements..., varietal name, shipment destination (city and state), and the number of lugs shipped (pounds). (b) When...

120 Years of Accelerators that Heal

CERN Multimedia

CERN. Geneva

2013-01-01

The discovery of X rays was made possible by the intelligent use of the best accelerator of the time. Since then, the development of particle accelerators has been at the root of both fundamental discoveries in physics and unforeseeable medical applications. The lecture will describe the major steps in this 120-year history of diagnostics and tumour therapy.   The first attempts to heal tumours with X rays were made only one month after Röntgen’s discovery, but the understanding of the mechanisms by which the radiation kills the cells and the introduction of dose fractionation took much longer. The use of X rays in diagnostics developed much faster and its benefits were very visible during the First World War. Today no tumour could be treated and no patient could be operated without a CT scan, which employs an X ray tube that is not very different from the one introduced by William Coolidge in 1912.   On the particle therapy frontier, more sophisticated and larger pa...

Giant magnetocaloric effect in isostructural MnNiGe-CoNiGe system by establishing a Curie-temperature window

KAUST Repository

Liu, E. K.

2013-03-28

An effective scheme of isostructural alloying was applied to establish a Curie-temperature window in isostructural MnNiGe-CoNiGe system. With the simultaneous accomplishment of decreasing structural-transition temperature and converting antiferromagnetic martensite to ferromagnetic state, a 200 K Curie-temperature window was established between Curie temperatures of austenite and martensite phases. In the window, a first-order magnetostructural transition between paramagnetic austenite and ferromagnetic martensite occurs with a sharp jump in magnetization, showing a magnetic entropy change as large as −40 J kg−1 K−1 in a 50 kOe field change. This giant magnetocaloric effect enables Mn1− x Co x NiGe to become a potential magnetic refrigerant.

Tokamak physics experiment: Diagnostic windows study

International Nuclear Information System (INIS)

Merrigan, M.; Wurden, G.A.

1995-11-01

We detail the study of diagnostic windows and window thermal stress remediation in the long-pulse, high-power Tokamak Physics Experiment (TPX) operation. The operating environment of the TPX diagnostic windows is reviewed, thermal loads on the windows estimated, and cooling requirements for the windows considered. Applicable window-cooling technology from other fields is reviewed and its application to the TPX windows considered. Methods for TPX window thermal conditioning are recommended, with some discussion of potential implementation problems provided. Recommendations for further research and development work to ensure performance of windows in the TPX system are presented

Mastering Windows 7 Deployment

CERN Document Server

Finn, Aidan; van Surksum, Kenneth

2011-01-01

Get professional-level instruction on Windows 7 deployment tools Enterprise-level operating system deployment is challenging and requires knowledge of specific tools. It is expected that Windows 7 will be extensively deployed in businesses worldwide. This comprehensive Sybex guide provides thorough coverage of the Microsoft deployment tools that were specifically created for Windows 7, preparing system administrators, MIS professionals, and corporate programmers to tackle the task effectively.Companies worldwide are expected to deploy Windows 7 as their enterprise operating system; system admi

Chi 3 dispersion in planar tantalum pentoxide waveguides in the telecommunications window.

Science.gov (United States)

Chen, Ruiqi Y; Charlton, Martin D B; Lagoudakis, Pavlos G

2009-04-01

We report on the dispersion of the third-order nonlinear susceptibility (chi(3) or "Chi 3") in planar Ta2O5 waveguides in the telecommunications spectral window. We utilize the observation of third-harmonic generation under ultrashort pulsed excitation as a reference-free characterization method of chi(3) and obtain a large nonlinear coefficient, 2x10(-13) esu, at 1550 nm. Our observation of efficient third-harmonic generation in Ta2O5 waveguides in the telecoms window reveals the potential of this material system in high-speed integrated nonlinear optical switches.

Handbook on Windows and Energy

DEFF Research Database (Denmark)

Thomsen, Kirsten Engelund; Schultz, Jørgen Munthe; Svendsen, Sv Aa Højgaard

The handbook on windows and energy is a general description of windows with the main focus put on the energy performance. Common window products are described by commonly used nomenclature, description of frame and sash conctructions and description of commonly used glazing types.The energy...... transmission through windows is described in detail including radiation, convection and conduction as well as solar transmittance of window glazing. The most used terms related to characterization of window energy performance are defined and calculation methods according to international standards...... flow and detailed calculation of light and solar transmittance is given.Different measurement techniques for characterization of window heat loss coefficient and total solar energy transmittance is described and references to interantional standards are given.Finally, the handbook includes...

22 CFR 219.160 - Communications.

Science.gov (United States)

2010-04-01

... 22 Foreign Relations 1 2010-04-01 2010-04-01 false Communications. 219.160 Section 219.160 Foreign Relations AGENCY FOR INTERNATIONAL DEVELOPMENT ENFORCEMENT OF NONDISCRIMINATION ON THE BASIS OF HANDICAP IN... communication with applicants, participants, personnel of other Federal entities, and members of the public. (1...

Social Media Management Strategies for Organizational Impression Management and their Effect on Public Perception

DEFF Research Database (Denmark)

Benthaus, Janek; Risius, Marten; Beck, Roman

2016-01-01

strategy, help companies to positively influence the public perception among social media users. A mixed methods approach is applied, where we quantitatively analyze 15 million user-generated Twitter messages containing information about 45 large global companies highly active on Twitter, as well as almost......With the growing importance of social media, companies increasingly rely on social media management tools to analyze social media activities and to professionalize their social media engagement. In this study, we evaluate how social media management tools, as part of an overarching social media...... 160 thousand corresponding messages sent from these companies via their corporate Twitter accounts. Additionally, we conducted interviews with six social media experts to gain complementary insights. By these means, we are able to identify significant differences between different social media...

21 CFR 606.160 - Records.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 7 2010-04-01 2010-04-01 false Records. 606.160 Section 606.160 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) BIOLOGICS CURRENT...) Distribution and disposition, as appropriate, of blood and blood products. (ii) Visual inspection of whole...

Drugs + HIV, Learn the Link

Medline Plus

Full Text Available ... projects/learn-link-drugs-hiv . 120x90 460x80 486x60 Social Media Send the message to young people and ... available for your use to share on your social media accounts. About the Campaign Overview The Learn ...

Lower HVAC Costs | Efficient Windows Collaborative

Science.gov (United States)

Foundry Foundry New Construction Windows Window Selection Tool Selection Process Design Guidance Installation Replacement Windows Window Selection Tool Assessing Options Selection Process Design Guidance Installation Understanding Windows Benefits Design Considerations Measuring Performance Performance Standards

Increased Light & View | Efficient Windows Collaborative

Science.gov (United States)

Foundry Foundry New Construction Windows Window Selection Tool Selection Process Design Guidance Installation Replacement Windows Window Selection Tool Assessing Options Selection Process Design Guidance Installation Understanding Windows Benefits Design Considerations Measuring Performance Performance Standards

Condensation Resistance (CR) | Efficient Windows Collaborative

Science.gov (United States)

Foundry Foundry New Construction Windows Window Selection Tool Selection Process Design Guidance Installation Replacement Windows Window Selection Tool Assessing Options Selection Process Design Guidance Installation Understanding Windows Benefits Design Considerations Measuring Performance Performance Standards

Fact Sheets & Publications | Efficient Windows Collaborative

Science.gov (United States)

Foundry Foundry New Construction Windows Window Selection Tool Selection Process Design Guidance Installation Replacement Windows Window Selection Tool Assessing Options Selection Process Design Guidance Installation Understanding Windows Benefits Design Considerations Measuring Performance Performance Standards

State Fact Sheets | Efficient Windows Collaborative

Science.gov (United States)

Foundry Foundry New Construction Windows Window Selection Tool Selection Process Design Guidance Installation Replacement Windows Window Selection Tool Assessing Options Selection Process Design Guidance Installation Understanding Windows Benefits Design Considerations Measuring Performance Performance Standards

State Code Guides | Efficient Windows Collaborative

Science.gov (United States)

Foundry Foundry New Construction Windows Window Selection Tool Selection Process Design Guidance Installation Replacement Windows Window Selection Tool Assessing Options Selection Process Design Guidance Installation Understanding Windows Benefits Design Considerations Measuring Performance Performance Standards

Low Conductance Spacers | Efficient Windows Collaborative

Science.gov (United States)

Foundry Foundry New Construction Windows Window Selection Tool Selection Process Design Guidance Installation Replacement Windows Window Selection Tool Assessing Options Selection Process Design Guidance Installation Understanding Windows Benefits Design Considerations Measuring Performance Performance Standards

Energy & Cost Savings | Efficient Windows Collaborative

Science.gov (United States)

Foundry Foundry New Construction Windows Window Selection Tool Selection Process Design Guidance Installation Replacement Windows Window Selection Tool Assessing Options Selection Process Design Guidance Installation Understanding Windows Benefits Design Considerations Measuring Performance Performance Standards

Provide Natural Light | Efficient Windows Collaborative

Science.gov (United States)

Foundry Foundry New Construction Windows Window Selection Tool Selection Process Design Guidance Installation Replacement Windows Window Selection Tool Assessing Options Selection Process Design Guidance Installation Understanding Windows Benefits Design Considerations Measuring Performance Performance Standards

Provide Fresh Air | Efficient Windows Collaborative

Science.gov (United States)

Foundry Foundry New Construction Windows Window Selection Tool Selection Process Design Guidance Installation Replacement Windows Window Selection Tool Assessing Options Selection Process Design Guidance Installation Understanding Windows Benefits Design Considerations Measuring Performance Performance Standards

Air Leakage (AL) | Efficient Windows Collaborative

Science.gov (United States)

Foundry Foundry New Construction Windows Window Selection Tool Selection Process Design Guidance Installation Replacement Windows Window Selection Tool Assessing Options Selection Process Design Guidance Installation Understanding Windows Benefits Design Considerations Measuring Performance Performance Standards

46 CFR 160.174-13 - Storage case.

Science.gov (United States)

2010-10-01

... 46 Shipping 6 2010-10-01 2010-10-01 false Storage case. 160.174-13 Section 160.174-13 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) EQUIPMENT, CONSTRUCTION, AND MATERIALS: SPECIFICATIONS AND APPROVAL LIFESAVING EQUIPMENT Thermal Protective Aids § 160.174-13 Storage case. Each thermal...

Enhanced piezoelectricity in (1 -x)Bi1.05Fe1-yAyO3-xBaTiO3 lead-free ceramics: site engineering and wide phase boundary region.

Science.gov (United States)

Zheng, Ting; Jiang, Zhenggen; Wu, Jiagang

2016-07-28

Site engineering has been employed to modulate the piezoelectric activity of high temperature (1 -x)Bi1.05Fe1-yScyO3-xBaTiO3 lead-free ceramics fabricated by a conventional solid-state method together with a quenching technique. The effects of x and y content on the phase structure, microstructure, and electrical properties have been investigated in detail. A wide rhombohedral (R) to pseudo-cubic (C) phase boundary was formed in the ceramics with x = 0.30 and 0 ≤y≤ 0.07, thus leading to enhanced piezoelectricity (d33 = 120-180 pC N(-1)), ferroelectricity (Pr = 19-22 μC cm(-2)) and a high Curie temperature (TC = 478-520 °C). In addition, the influence of different element substitutions for Fe(3+) on phase structure and electrical behavior was also investigated. Improved piezoelectricity (d33 = 160-180 pC N(-1)) and saturated P-E loops can be simultaneously achieved in the ceramics with A = Sc, Ga, and Al due to the R-C phase boundary. As a result, site engineering may be an efficient way to modulate the piezoelectricity of BiFeO3-BaTiO3 lead-free ceramics.

Gabor windows supported on [-1,1] and compactly supported dual windows

DEFF Research Database (Denmark)

Christensen, Ole; Kim, H. O.; Rae Young, Kim

2010-01-01

window. More precisely, we show that if b window supported on [-N, N]. Under the additional assumption that g is continuous and only has a finite number of zeros on inverted left perpendicular-1, 1inverted right perpendicular, we...... characterize the frame property of {E(mb)T(n)g}(m,n is an element of Z). As a consequence we obtain easily verifiable criteria for a function g to generate a Gabor frame with a dual window having compact support of prescribed size....

Designing for Windows 8 fundamentals of great design in Windows Store apps

CERN Document Server

Schooley, Brent

2013-01-01

Designing for Windows 8 is a fast-paced, 150-page primer on the key design concepts you need to create successful Windows 8 apps. This book will help you design a user interface that is both delightful and effective, feels 'right' to your users, and encapsulates a great Windows 8 experience. In this book, you will: Meet the building blocks of solid Windows 8 UI design in a well-designed sample app. Learn how to incorporate key design elements into your apps, such as the app bar, charms and subtle animations from the animation library. Find out how to deliver the core experience that your users

Design windows and cost analysis on helical reactors

International Nuclear Information System (INIS)

Kozaki, Y.; Imagawa, S.; Sagara, A.

2007-01-01

The LHD type helical reactors are characterized by a large major radius but slender helical coil, which give us different approaches for power plants from tokamak reactors. For searching design windows of helical reactors and discussing their potential as power plants, we have developed a mass-cost estimating model linked with system design code (HeliCos), thorough studying the relationships between major plasma parameters and reactor parameters, and weight of major components. In regard to cost data we have much experience through preparing ITER construction. To compare the weight and cost of magnet systems between tokamak and helical reactors, we broke down magnet systems and cost factors, such as weights of super conducting strands, conduits, support structures, and winding unit costs, through estimating ITER cost data basis. Based on FFHR2m1 deign we considered a typical 3 GWth helical plant (LHD type) with the same magnet size, coil major radius Rc 14 m, magnetic energy 120 GJ, but increasing plasma densities. We evaluated the weight and cost of magnet systems of 3 GWth helical plant, the total magnet weights of 16,000ton and costs of 210 BYen, which are similar values of tokamak reactors (10,200 ton, 110 BYen in ITER 2002 report, and 21,900 ton, 275 BYen in ITER FDR1999). The costs of strands and winding occupy 70% of total magnet costs, and influence entire power plants economics. The design windows analysis and comparative economics studies to optimize the main reactor parameters have been carried out. Economics studies show that it is misunderstanding to consider helical coils are too large and too expensive to achieve power plants. But we should notice that the helical reactor design windows and economics are very sensitive to allowable blanket space (depend on ergodic layer conditions) and diverter configuration for decreasing heat loads. (orig.)

Crafting digital media

CERN Document Server

James, Daniel

2010-01-01

Open source software, also known as free software, now offers a creative platform with world-class programs. Just ask the people who have completed high-quality projects or developed popular web 2.0 sites using open source desktop applications. This phenomenon is no longer underground or restricted to techies - there have been more than 61 million downloads of the Audacity audio editor and more than 60 million downloads of the GIMP for Windows photographic tool from SourceForge.net alone. Crafting Digital Media is your foundation course in photographic manipulation, illustration, animation, 3D

7 CFR 160.46 - Identification of containers.

Science.gov (United States)

2010-01-01

... 7 Agriculture 3 2010-01-01 2010-01-01 false Identification of containers. 160.46 Section 160.46... STANDARDS FOR NAVAL STORES Request Inspection by Licensed Inspectors § 160.46 Identification of containers. Containers packed with naval stores which have been inspected, classified, graded, and certified by a...

40 CFR 160.31 - Testing facility management.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 23 2010-07-01 2010-07-01 false Testing facility management. 160.31... GOOD LABORATORY PRACTICE STANDARDS Organization and Personnel § 160.31 Testing facility management. For each study, testing facility management shall: (a) Designate a study director as described in § 160.33...

7 CFR 160.73 - Availability of standards.

Science.gov (United States)

2010-01-01

... 7 Agriculture 3 2010-01-01 2010-01-01 false Availability of standards. 160.73 Section 160.73 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Standards... STANDARDS FOR NAVAL STORES Loan and Care of United States Standards § 160.73 Availability of standards. (a...

Vacancy-type defects in In{sub x}Ga{sub 1−x}N grown on GaN templates probed using monoenergetic positron beams

Energy Technology Data Exchange (ETDEWEB)

Uedono, Akira [Division of Applied Physics, Faculty of Pure and Applied Science, University of Tsukuba, Tsukuba, Ibaraki 305-8573 (Japan); Watanabe, Tomohito; Kimura, Shogo; Zhang, Yang; Lozac' h, Mickael [Graduate School of Pure and Applied Sciences, University of Tsukuba, Tsukuba, Ibaraki 305-8573 (Japan); Sang, Liwen; Sumiya, Masatomo [Wide Bandgap Material Group, National Institute for Materials Science, Tsukuba 305-0044 (Japan); Ishibashi, Shoji [Nanosystem Research Institute (NRI) “RICS,” National Institute of Advanced Industrial Science and Technology (AIST), Tsukuba, Ibaraki 305-8568 (Japan); Oshima, Nagayasu; Suzuki, Ryoichi [Research Institute of Instrumentation Frontier, National Institute of Advanced Industrial Science and Technology, Tsukuba, Ibaraki 305-8568 (Japan)

2013-11-14

Native defects in In{sub x}Ga{sub 1−x}N layers grown by metalorganic chemical vapor deposition were studied using monoenergetic positron beams. Measurements of Doppler broadening spectra of the annihilation radiation and lifetime spectra of positrons for a 200-nm-thick In{sub 0.13}Ga{sub 0.87}N layer showed that vacancy-type defects were introduced by InN alloying, and the major species of such defects was identified as complexes between a cation vacancy and nitrogen vacancies. The presence of the defects correlated with lattice relaxation of the In{sub 0.13}Ga{sub 0.87}N layer and the increase in photon emissions from donor-acceptor-pair recombination. The species of native defects in In{sub 0.06}Ga{sub 0.94}N layers was the same but its concentration was decreased by decreasing the InN composition. With the layer thickness increased from 120 nm to 360 nm, a defect-rich region was introduced in the subsurface region (<160 nm), which can be associated with layer growth with the relaxation of compressive stress.

20 CFR 401.160 - Health or safety.

Science.gov (United States)

2010-04-01

... 20 Employees' Benefits 2 2010-04-01 2010-04-01 false Health or safety. 401.160 Section 401.160... INFORMATION Disclosure of Official Records and Information § 401.160 Health or safety. The Privacy Act allows us to disclose information in compelling circumstances where an individual's health or safety is...

Present state of the study of 160-minutes solar oscillation

International Nuclear Information System (INIS)

Severny, A.B.; Kotov, V.A.; Tsap, T.T.

1981-01-01

Global oscillation of the Sun with a period of 160 min were first discovered in 1974 and since observed in Crimea during the last 6 years; they were confirmed, in 1976-1979, by Doppler measurements at Stanford (Scherrer et al., 1980) and quite recently by observations of Fossat and Grec at the south geographic pole. The average amplitude of the oscillation is about 0.5 m s -1 . The phase shows remarkable stability at the period 160.010 min and good agreement between different sites on the Earth; therefore, this oscillation should now be recognized as definitely of solar origin. It is probably accompanied by synchronous fluctuations in the IR brightness and radio-emission of the Sun, and exhibits a dependence of the amplitude on the phase of solar rotation (with a peak of power at 27.2 days). In agreement with results of the Birmingham group and the South Pole observation we also find evidence in favour of a discrete spectrum within the 5 min global oscillations of the Sun, with the average splitting of about 69,5 μHz in frequency. Strict gas-dynamical equations being solved in the adiabatic approximation for a polytropic sphere n = 3 display the pattern of radial oscillations with wave separated by 120 m time-intervals filled with high frequency (and split by 117 μHz) oscillations implying a similarity with the observed pattern. (orig.)

Multidimensional digital image representations using generalized Kaiser-Bessel window functions.

Science.gov (United States)

Lewitt, R M

1990-10-01

Inverse problems that require the solution of integral equations are inherent in a number of indirect imaging applications, such as computerized tomography. Numerical solutions based on discretization of the mathematical model of the imaging process, or on discretization of analytic formulas for iterative inversion of the integral equations, require a discrete representation of an underlying continuous image. This paper describes discrete image representations, in n-dimensional space, that are constructed by the superposition of shifted copies of a rotationally symmetric basis function. The basis function is constructed using a generalization of the Kaiser-Bessel window function of digital signal processing. The generalization of the window function involves going from one dimension to a rotationally symmetric function in n dimensions and going from the zero-order modified Bessel function of the standard window to a function involving the modified Bessel function of order m. Three methods are given for the construction, in n-dimensional space, of basis functions having a specified (finite) number of continuous derivatives, and formulas are derived for the Fourier transform, the x-ray transform, the gradient, and the Laplacian of these basis functions. Properties of the new image representations using these basis functions are discussed, primarily in the context of two-dimensional and three-dimensional image reconstruction from line-integral data by iterative inversion of the x-ray transform. Potential applications to three-dimensional image display are also mentioned.

Radiosensitization of high-Z compounds by medium-energy 160 kV vs. high-energy 6 MV X-rays for radiation therapy: Theoretical, in vitro and in vivo studies of platinum compounds activating glioma F98 cancer cells

Science.gov (United States)

Lim, S.; Pradhan, A.; Nahar, S.; Montenegro, M.; Barth, R.; Nakkula, R.; Turro, C.

2013-03-01

Energy dependence of X-ray irradiation of high-Z compounds for enhanced radiosensitization is explored thoeretically and via in vitro and in vivo experiments. The cell killing ability of medium-energy X-rays from 160 kV source are found to be more effective than 6 MV X-rays in activating high-Z contrast agents. Results are presented for a newly synthesized Pt compound, Pyridine Terpyridine Pt(II) Nitrate ([Pt(typ)(py)]) and carboplatin in treating F98 rat glioma. In-vitro results show considerable reduction in cell viability for radiosensitized cells irradiated with a 160 kV irradiator. Cells treated with 6 MV LINAC radiation find little variation with radiation dose. Maximum dose enhancement factors (DEFs) and minimum cancer cell survival fractions correspond to 50-200 keV range, and fall rapidly at higher energies. Theoretical calculations of photoelectric absorption vis-a-vis total scattering demonstrates this energy dependence. However, in vivo studies of rats treated with [Pt(tpy)(py)] had a severe negative neurotoxic response, confirmed by histopathological analysis. But subsequent in vivo studies using carboplatin showed very positive results in the treatment of F98 glioma bearing rats and potential clinical radiation therapy.

Drugs + HIV, Learn the Link

Medline Plus

Full Text Available ... projects/learn-link-drugs-hiv . 120x90 460x80 486x60 Social Media Send the message to young people and to ... available for your use to share on your social media accounts. About the Campaign Overview The Learn the ...

Radiolabelling of RC-160: preliminary results

International Nuclear Information System (INIS)

Verdera, E.S.; Balter Binsky, H.S.; Robles, A.M.; Rodriguez, G.; Souto, B.; Laiz, J.; Oliver, P.; Leon, E.

1998-01-01

Vapreotide (RC-160) was labelled with 125 I using Chloramine-T and Iodogen methods and with 99m Tc by a direct method with sodium ditionite as reducing agent in the presence of ascorbic acid. Several methods of purification and quality control were evaluated. Yields of the reactions and of purification steps were calculated. The results obtained for the radioiodination reactions showed higher yields when limiting Chloramine-T method was used. Labelling of RC-160 with 99m Tc indicated better yields when high radioactivity concentration of the radionuclide was used. Stability of the products obtained was assessed at different post-labelling times by selected quality control methods: Sep-Pak cartridge as purification method and chromatography by RP-HPLC and ITLC-SG using saline solution as solvent. It was demonstrated that I-125-RC-160 and Tc-99m-RC-160 were stable during five weeks (at -20 deg. C) and 6 hours (at room temperature) respectively. Preliminary biodistribution of Tc-99m-RC-160 in normal rats and mice were done showing different biological behaviour compared with control animals injected with pertechnetate. In conclusion, RC-160 was successfully labelled with both radionuclides, with radiochemical purity higher than 95%. These results encourage further research work in animal models as well as to investigate the biochemical behaviour of radiolabelled peptide. (author)

Generating high-brightness and coherent soft x-ray pulses in the water window with a seeded free-electron laser

Directory of Open Access Journals (Sweden)

Kaishang Zhou

2017-01-01

Full Text Available We propose a new scheme to generate high-brightness and temporal coherent soft x-ray radiation in a seeded free-electron laser. The proposed scheme is based on the coherent harmonic generation (CHG and superradiant principles. A CHG scheme is first used to generate a coherent signal at ultrahigh harmonics of the seed. This coherent signal is then amplified by a series of chicane-undulator modules via the fresh bunch and superradiant processes in the following radiator. Using a representative of a realistic set of parameters, three-dimensional simulations have been carried out and the simulations results demonstrated that 10 GW-level ultrashort (∼20  fs coherent radiation pulses in the water window can be achieved by using a 1.6 GeV electron beam based on the proposed technique.

The Double-Edged Effects of Social Media Terror Communication

DEFF Research Database (Denmark)

Nickel, Sandro

2014-01-01

This paper connects the effects of social media on terror/anti-terror communication with dynamics and consequences of surveillance. Citizens become via social media more independent from mass media and more interconnected. This is also valid when citizens engage in terror/anti-terror communication...... that social media contribute to extending surveillance: by being a temptation for intelligence services, by not resisting state authorities and via constructing threat perceptions among populations which in effect deliver security politicians ‘windows of opportunity’ in order to implement ever more....... However, via social media citizens also become targets of the ‘collect-it-all’ surveillance, which was revealed to the global public in 2013. I argue that due to such surveillance some citizens might start to censor themselves and that surveillance inflicts with a number of human rights. I further argue...

CRL X-ray tube

International Nuclear Information System (INIS)

Kolchevsky, N.N.; Petrov, P.V.

2015-01-01

A novel types of X-ray tubes with refractive lenses are proposed. CRL-R X-ray tube consists of Compound Refractive Lens- CRL and Reflection X-ray tube. CRL acts as X-ray window. CRL-T X-ray consists of CRL and Transmission X-ray tube. CRL acts as target for electron beam. CRL refractive lens acts as filter, collimator, waveguide and focusing lens. Properties and construction of the CRL X-ray tube are discussed. (authors)

Windows with improved energy performances

DEFF Research Database (Denmark)

Laustsen, Jacob Birck; Svendsen, Svend

2003-01-01

Heat loss through windows represents a considerable part of the total heat loss from houses. However, apart from providing daylight access and view, windows offer a unique potential for solar gain to be exploited during the heating season. Until now valuation of the energy performance of windows...... has primary focused on the heat loss coefficient, U-value. However, as the U-value, especially for the glazing part, has improved considerably during the last years, the total solar energy transmittance, g-value, has become equally important to the total energy performance of windows. Improved energy...... resulted in a window with a positive net energy gain (in short the Net Gain Window), which means that it contributes to the space heating of the building. All improvements are based on existing technology and manufacturing methods. The results from this work show that the energy performances of windows can...

21 CFR 573.160 - Ammoniated rice hulls.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Ammoniated rice hulls. 573.160 Section 573.160... Additive Listing § 573.160 Ammoniated rice hulls. The food additive ammoniated rice hulls may be safely... obtained by the treatment of ground rice hulls with monocalcium phosphate and anhydrous ammonia at a...

46 CFR 160.176-21 - User manuals.

Science.gov (United States)

2010-10-01

... 46 Shipping 6 2010-10-01 2010-10-01 false User manuals. 160.176-21 Section 160.176-21 Shipping...: SPECIFICATIONS AND APPROVAL LIFESAVING EQUIPMENT Inflatable Lifejackets § 160.176-21 User manuals. (a) The manufacturer must develop a user's manual for each model of inflatable lifejacket. The content of the manual...

7 CFR 160.84 - Identification of shipments.

Science.gov (United States)

2010-01-01

... 7 Agriculture 3 2010-01-01 2010-01-01 false Identification of shipments. 160.84 Section 160.84... STANDARDS FOR NAVAL STORES Sales and Shipments § 160.84 Identification of shipments. The invoice or contract of sale of any naval stores in commerce shall identify and describe the article in accordance with...

Beginning Windows 8.1

CERN Document Server

Halsey, Mike

2013-01-01

Windows 8 has been described by Microsoft as its 'boldest' Windows release ever and the 8.1 update enhances the paradigm further. Beginning Windows 8.1 takes you through the new features and helps you get more out of the familiar to reveal the fullest possibilities for this amazing new operating system. You will learn, with non-technical language used throughout, how to get up and running in the new Windows interface, minimize downtime, maximize productivity, and harness the features you never knew existed to take control of your computer and enjoy the peace of mind and excitement that comes w

Composite Monopack for 120mm Mortar, With Plastic Pallet Adapters on a 42" x 53" Wooden Pallet, MIL-STD-1660 Tests, "Design Criteria for Ammunition Unit Loads", and Extreme Temperature Tests

National Research Council Canada - National Science Library

Dugan, Jeffery L

2005-01-01

... (AMSRD-AAR-AIL-P) to conduct MIL-STD-1660 Tests to determine if the composite monopack for the 120MM mortar, with plastic pallet adapters on a 42" x 53" wooden pallet, designed by US Army ARDEC and manufactured...

Visual merchandising window display

Directory of Open Access Journals (Sweden)

Opris (Cas. Stanila M.

2013-12-01

Full Text Available Window display plays a major part in the selling strategies; it does not only include the simple display of goods, nowadays it is a form of art, also having the purpose of sustaining the brand image. This article wants to reveal the tools that are essential in creating a fabulous window display. Being a window designer is not an easy job, you have to always think ahead trends, to have a sense of colour, to know how to use light to attract customers in the store after only one glance at the window. The big store window displays are theatre scenes: with expensive backgrounds, special effects and high fashion mannequins. The final role of the displays is to convince customers to enter the store and trigger the purchasing act which is the final goal of the retail activity.

Windows 7 is supported at CERN

CERN Multimedia

IT Department

2010-01-01

The new version of the Windows operating system - Windows 7 - is now officially supported at CERN. Windows 7 32-bit is now the default operating system for the new computers at CERN. What’s new in Windows 7 Users of Windows XP will find many new features and options. Users of Windows Vista will feel very familiar with one major difference: higher performance and better responsiveness of the operating system. Other enhancements include: refined Aero desktop that makes it easier to navigate between your different application windows; new snapping windows that allows user to resize a window simply by dragging it to the edge of the screen and “pin” that allows grouping and arranging often accessed applications on the taskbar. Windows 7 introduces the new concept of libraries – containers for user files that have links to different local or network folders. By default, users can see four libraries: Documents, Music, Pictures and Videos. These libraries point to the cor...

Contrast media in diagnostic radiology. 3. rev. and enlarged ed.

International Nuclear Information System (INIS)

Elke, M.; Gueckel, C.; Schmitt, H.E.; Felder, E.; Froehlich, J.M.; Radue, E.W.; Scheidegger, D.; Speck, U.

1992-01-01

With the 3rd edition of this book a comprehensive description is provided of all the properties and side-effects of contrast media as well as of the available remedies in mishaps caused by these agents. The individual chapters are headed as follows: (s. table of contents). 1. Introduction. 2. Contrast media for X-ray radiography, MRT, and ultrasonic scanning. 3. Kinetics of X-ray contrast media. 4. Pharamcodynamics of X-ray contrast media. 5. Side-effects of X-ray contrast media and complications encountered in practical radiology. 6. The mobile reanimation unit and the emergency kit. 7. Treatment of reactions to contrast media. 8. Appendix. 9. Bibliography, subject index. (orig./MG) With 25 figs., 5 text tabs., 39 tabs [de

GA microwave window development

International Nuclear Information System (INIS)

Moeller, C.P.; Kasugai, A.; Sakamoto, K.; Takahashi, K.

1994-10-01

The GA prototype distributed window was tested in a 32 mm diam. waveguide system at a power density suitable for a MW gyrotron, using the JAERI/Toshiba 110 GHz long pulse internal converter gyrotron in the JAERI test stand. The presence of the untilted distributed window had no adverse effect on the gyrotron operation. A pulse length of 10 times the calculated thermal equilibrium time (1/e time) of 30 msec was reached, and the window passed at least 750 pulses greater than 30 msec and 343 pulses greater than 60 msec. Beyond 100 msec, the window calorimetry reached steady state, allowing the window dissipation to be measured in a single pulse. The measured loss of 4.0% agrees both with the estimated loss, on which the stress calculations are based, and with the attenuation measured at low power in the HE 11 mode. After the end of the tests, the window was examined; no evidence of arcing air coating was found in the part of the window directly illuminated by the microwaves, although there was discoloration in a recess containing an optical diagnostic which outgassed, causing a local discharge to occur in that recess. Finally, there was no failure of the metal-sapphire joints during a total operating time of 50 seconds consisting of pulses longer than 30 msec

A wide-gap a-SiC:H PV-powered electrochromic window coating

Energy Technology Data Exchange (ETDEWEB)

Gao, W.; Lee, S.H.; Xu, Y.; Benson, D.K.; Deb, S.K.; Branz, H.M. [National Renewable Energy Lab., Golden, CO (United States)

1998-09-01

The authors report on the first monolithic, amorphous-silicon-based, photovoltaic-powered electrochromic window coating. The coating employs a wide bandgap a-Si{sub 1{minus}x}C{sub x}:H n-i-p photovoltaic (PV) cell as a semitransparent power supply, and a Li{sub y}WO{sub 3}/LiAlF{sub 4}/V{sub 2}O{sub 5} electrochromic (EC) device as an optical-transmittance modulator. The EC device is deposited directly on top of a PV cell that coats a glass substrate. The a-Si{sub 1{minus}x}C{sub x}:H PV cell has a Tauc gap of 2.2 eV and a transmittance of 60--80% over a large portion of the visible light spectrum. The authors reduced the thickness of the device to about 600 {angstrom} while maintaining a 1-sun open-circuit voltage of 0.9 V and short-circuit current of 2 mA/cm{sup 2}. The prototype 16 cm{sup 2} PV/EC device modulates the transmittance by more than 60% over a large portion of the visible spectrum. The coloring and bleaching times of the EC device are approximately 1 minute under normal operating conditions ({+-} 1 volt). A brief description of photoelectrochromic windows study is also given.

21 CFR 160.150 - Frozen egg whites.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 2 2010-04-01 2010-04-01 false Frozen egg whites. 160.150 Section 160.150 Food... HUMAN CONSUMPTION EGGS AND EGG PRODUCTS Requirements for Specific Standardized Eggs and Egg Products § 160.150 Frozen egg whites. (a) Frozen egg whites, frozen egg albumen is the food prepared by freezing...

PENGARUH MEDIA PEMBELAJARAN DAN STRATEGI BELAJAR TERHADAP HASIL BELAJAR SISWA KELAS X PADA MATA PELAJARAN EKONOMI SMA SEDES SAPIENTIAE SEMARANG (studi pada tahun ajaran 2015/2016.

Directory of Open Access Journals (Sweden)

Desi Marintan

2017-02-01

Full Text Available According to early observation in Sedes Sapientaie Semarang Senior High School the learning’s result of economic subject is still in low category.The purpose of this research to know the influence of study media and learning study towards learning’s result of the students who are in X grade at economic subject in Sedes Sapientiae Semarang Senior High School. The population of this research is all the X student’s class in Sedes Sapientiae Semarang Senior High School by using Proportionate Stratified Random Sampling technique. Result of this research indicates that silmutantly media of study and learning strategy towards learning’s result at economic subject has effect 58,4%. And partially, media of study has effect toward’s learning’s result of economic subjects amount 25,00% and learning strategy towards students learning’s result at economic subject as amount 20,25%. Based to the research, can be conduded that media of study and learning strategy have positive effects towards the learning result of X class students at economic subject simultantly or partially.

Music@Microsoft.Windows: Composing Ambience

Science.gov (United States)

Rickert, Thomas

2010-01-01

It is well known, of course, that all Windows versions except for 3.1 have a brief (four to six second) piece of music indicating that Windows is booted and ready for use. While the music may indicate Windows has booted, it bears no immediately discernable relation to the various uses we might actually put Windows to--working, gaming,…

Windows 8 simplified

CERN Document Server

McFedries, Paul

2012-01-01

The easiest way for visual learners to get started with Windows 8 The popular Simplified series makes visual learning easier than ever, and with more than 360,000 copies sold, previous Windows editions are among the bestselling Visual books. This guide goes straight to the point with easy-to-follow, two-page tutorials for each task. With full-color screen shots and step-by-step directions, it gets beginners up and running on the newest version of Windows right away. Learn to work with the new interface and improved Internet Explorer, manage files, share your computer, and much more. Perfect fo

New Liquid Crystal Smart Window and its Production Process (SmartWin II)

DEFF Research Database (Denmark)

Jensen, Karsten Ingerslev; Kristiansen, Finn Harken; Schultz, Jørgen Munthe

2005-01-01

window: 1) with sufficient area glazing to meet the market, 2) using a technology which supplies the glazing with three operating modes: 2a) a reflective mode limiting the glazing overheating, 2b) a transparent mode with an excellent transparency, 2c) a scattering mode having a grey scale, 3) for which...... large market potential for this technology. Conception and realisation of a pre-industrial machine for manufacturing smart windows were obtained. By means of this pre-industrial machine, the sample surface area was progressive increased from lab-scale (approx. 10 cm sq.) up to 60 cm x 80 cm at Mid...

21 CFR 160.185 - Dried egg yolks.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 2 2010-04-01 2010-04-01 false Dried egg yolks. 160.185 Section 160.185 Food and... CONSUMPTION EGGS AND EGG PRODUCTS Requirements for Specific Standardized Eggs and Egg Products § 160.185 Dried egg yolks. (a) Dried egg yolks, dried yolks is the food prepared by drying egg yolks that conform to...

21 CFR 160.190 - Frozen egg yolks.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 2 2010-04-01 2010-04-01 false Frozen egg yolks. 160.190 Section 160.190 Food and... CONSUMPTION EGGS AND EGG PRODUCTS Requirements for Specific Standardized Eggs and Egg Products § 160.190 Frozen egg yolks. (a) Frozen egg yolks, frozen yolks is the food prepared by freezing egg yolks that...

21 CFR 160.145 - Dried egg whites.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 2 2010-04-01 2010-04-01 false Dried egg whites. 160.145 Section 160.145 Food and... CONSUMPTION EGGS AND EGG PRODUCTS Requirements for Specific Standardized Eggs and Egg Products § 160.145 Dried egg whites. (a) The food dried egg whites, egg white solids, dried egg albumen, egg albumen solids is...

Comparison of the Window-Frame RHIC-abort kicker with C-type Kicker

International Nuclear Information System (INIS)

Tsoupas, N.; McMahan, Brandon

2014-01-01

The high intensity proton bunches (~2.5x10 11 p/bunch ) circulating in RHIC increase the temperature of the ferrite-made RHIC-abort-kickers above the Curie point; as a result, the kickers cannot provide the required field to abort the beam at the beam dump. A team of experts in the CAD department worked on modifying the design of the window-frame RHIC-abort kicker to minimize the hysteresis losses responsible for the increase of the ferrite's temperature. In this technical note we report some results from the study of two possible modifications of the window-frame RHIC-abort kicker, and we compare these results with those of a propose C-type RHIC-abort kicker. We also include an Appendix where we describe a method which may further reduce the hysteresis losses of the window-frame kicker.

Monte Carlo simulations of the dose from imaging with GE eXplore 120 micro-CT using GATE

Energy Technology Data Exchange (ETDEWEB)

Bretin, Florian; Bahri, Mohamed Ali; Luxen, André; Phillips, Christophe; Plenevaux, Alain; Seret, Alain, E-mail: aseret@ulg.ac.be [Cyclotron Research Centre, University of Liège, Sart Tilman B30, Liège 4000 (Belgium)

2015-10-15

Purpose: Small animals are increasingly used as translational models in preclinical imaging studies involving microCT, during which the subjects can be exposed to large amounts of radiation. While the radiation levels are generally sublethal, studies have shown that low-level radiation can change physiological parameters in mice. In order to rule out any influence of radiation on the outcome of such experiments, or resulting deterministic effects in the subjects, the levels of radiation involved need to be addressed. The aim of this study was to investigate the radiation dose delivered by the GE eXplore 120 microCT non-invasively using Monte Carlo simulations in GATE and to compare results to previously obtained experimental values. Methods: Tungsten X-ray spectra were simulated at 70, 80, and 97 kVp using an analytical tool and their half-value layers were simulated for spectra validation against experimentally measured values of the physical X-ray tube. A Monte Carlo model of the microCT system was set up and four protocols that are regularly applied to live animal scanning were implemented. The computed tomography dose index (CTDI) inside a PMMA phantom was derived and multiple field of view acquisitions were simulated using the PMMA phantom, a representative mouse and rat. Results: Simulated half-value layers agreed with experimentally obtained results within a 7% error window. The CTDI ranged from 20 to 56 mGy and closely matched experimental values. Derived organ doses in mice reached 459 mGy in bones and up to 200 mGy in soft tissue organs using the highest energy protocol. Dose levels in rats were lower due to the increased mass of the animal compared to mice. The uncertainty of all dose simulations was below 14%. Conclusions: Monte Carlo simulations proved a valuable tool to investigate the 3D dose distribution in animals from microCT. Small animals, especially mice (due to their small volume), receive large amounts of radiation from the GE eXplore 120

Deep tissue imaging of microfracture and non-displaced fracture of bone using the second and third near-infrared therapeutic windows

Science.gov (United States)

Sordillo, Laura A.; Pu, Yang; Sordillo, P. P.; Budansky, Yury; Alfano, Robert R.

2014-03-01

Near-infrared (NIR) light in the wavelengths of 700 nm to 2,000 nm has three NIR optical, or therapeutic, windows, which allow for deeper depth penetration in scattering tissue media. Microfractures secondary to repetitive stress, particularly in the lower extremities, are an important problem for military recruits and athletes. They also frequently occur in the elderly, or in patients taking bisphosphonates or denosumab. Microfractures can be early predictors of a major bone fracture. Using the second and third NIR therapeutic windows, we investigated the results from images of chicken bone and human tibial bone with microfractures and non-displaced fractures with and without overlying tissues of various thicknesses. Images of bone with microfractures and non-displaced fractures with tissue show scattering photons in the third NIR window with wavelengths between 1,650 nm and 1,870 nm are diminished and absorption is increased slightly from and second NIR windows. Results from images of fractured bones show the attenuation length of light through tissue in the third optical window to be larger than in the second therapeutic window. Use of these windows may aid in the detection of bone microfractures, and thus reduce the incidence of major bone fracture in susceptible groups.

PENGARUH MOTIVASI BELAJAR, DISIPLIN BELAJAR DAN MEDIA PEMBELAJARAN TERHADAP KESIAPAN BELAJAR SISWA KELAS X ADMINISTRASI PERKANTORAN PADA MATA DIKLAT MENGELOLA PERALATAN KANTOR DI SMK NU 01 KENDAL

Directory of Open Access Journals (Sweden)

Ayu Fitria Yanida, Hengky Pramusinto

2014-11-01

Full Text Available Tujuan penelitian ini adalah untuk mengetahui Pengaruh motivasi belajar, disiplin belajar dan media pembelajaran terhadap kesiapan belajar siswa kelas X administrasi perkantoran pada mata diklat mengelola peralatan kantor di SMK NU 01 Kendal baik secara simultan maupun parsial.Populasi dalam penelitian ini adalah siswa kelas X jurusan administrasi perkantoran sebanyak 94siswa.Metode pengumpulan data yang digunakan adalah metode kuesioner dan dokumentasi.Teknik analisis data menggunakan analisis deskriptif persentase, analisis regresi linier berganda, analisis uji asumsi klasik, dan analisis uji hipotesis.Analisis regresi berganda menunjukkan bahwa ada pengaruh motivasi belajar, disiplin belajar dan media pembelajaran terhadap kesiapan belajar siswa kelas X administrasi perkantoran pada mata diklat mengelola peralatan kantor di SMK NU 01 Kendal baik secara simultan maupun parsial. Preparation to studyis the basic need that must be done by students Office Equipment learning outcomes. Learning readiness can be influenced by learning motivation, learning discipline and learning media. The problem of this study:Was there are any influence of learning motivation, learning discipline and learning media toward the 10th grade students’ learning readiness of OfficeAdministration in managing Office Equipment in SMK NU 01 Kendal. The population were 10thgrade student of Office Administration at SMK NU 01 Kendal, they were 94 students. The data were collected by questiononaires and documentation. The data were analyzed by percentage desciptive analiysis, multiple linear regression analysis, analysis classical assumption test, hypothesis testing and SPSS analysis. The results of multiple linear regression analysis showed that the equation Y = 7.472 + 0.163X1 + 0.155X2+ 0.369X3, with F test was obtained F = 16.278 with a significance 0.000 and less than 0.05. Simultaneously, the influence of learning motivation, learning discipline and learning media toward

Drugs + HIV, Learn the Link

Medline Plus

Full Text Available ... at: http://www.drugabuse.gov/news-events/public-education-projects/learn-link-drugs-hiv . 120x90 460x80 486x60 Social Media Send the message to young people and to parents, teachers, and the media about the link between drug ...

A review of the benefits and rationale of viewing liver window settings for abdominal computed tomography scans

International Nuclear Information System (INIS)

Dang, Tan; Mandarano, Giovanni

2006-01-01

There have been many different opinions over the efficacy of routinely incorporating liver-window settings in abdominal computed tomography (CT) scans. As a result, different clinical centres have varying protocols for incorporating liver-windows for abdominal CT scans. This investigation aims to explore and determine whether various clinical centres throughout Victoria use liver-window settings selectively or routinely and their justification for doing so. An additional purpose is also to assess the benefits and rationale of liver-window settings in supplementing routine soft-tissue-windows for abdominal CT examinations by reviewing evidenced-based studies. Surveys were sent out to CT supervisors at various clinical centres, including private and public institutions. This achieved an overall response rate of 74 per cent. Results indicate that the majority of clinical centres throughout Victoria routinely incorporate liver-window settings for all abdominal CT examinations. Forty four per cent (11/25) of respondents stated that they utilise liver-window settings selectively for abdominal CT examinations. Most of these respondents (7/11 = 63 per cent) believed that soft-tissue-window settings alone are adequate to demonstrate hepatic lesions; particularly if intravenous contrast media is used and the liver is captured in the arterial, venous and/or delayed phases. The benefits and rationale of incorporating liver-window settings for all abdominal computed tomography scans has been questioned by two well noted studies in the United States. These evidence-based studies suggest that such additional settings do not offer further advantages in detecting hepatic disease, when compared to soft-tissue-windows alone. Review of the available literature provides additional evidence suggesting that the routine use of liver-window settings in conjunction with soft-tissue-windows offers no further advantages in the detection of hepatic diseases. This investigation found, however

Digital media in the home: technical and research challenges

Science.gov (United States)

Ribas-Corbera, Jordi

2005-03-01

This article attempts to identify some of the technology and research challenges facing the digital media industry in the future. We first discuss several trends in the industry, such as the rapid growth of broadband Internet networks and the emergence of networking and media-capable devices in the home. Next, we present technical challenges that result from these trends, such as effective media interoperability in devices, and provide a brief overview of Windows Media, which is one of the technologies in the market attempting to address these challenges. Finally, given these trends and the state of the art, we argue that further research on data compression, encoder optimization, and multi-format transcoding can potentially make a significant technical and business impact in digital media. We also explore the reasons that research on related techniques such as wavelets or scalable video coding is having a relatively minor impact in today"s practical digital media systems.

Windows registry forensics advanced digital forensic analysis of the Windows registry

CERN Document Server

Carvey, Harlan

2011-01-01

Harlan Carvey brings readers an advanced book on Windows Registry - the most difficult part of Windows to analyze in forensics! Windows Registry Forensics provides the background of the Registry to help develop an understanding of the binary structure of Registry hive files. Approaches to live response and analysis are included, and tools and techniques for postmortem analysis are discussed at length. Tools and techniques will be presented that take the analyst beyond the current use of viewers and into real analysis of data contained in the Registry. This book also has a DVD containing tools, instructions and videos.

Calibration-free quantification of interior properties of porous media with x-ray computed tomography

International Nuclear Information System (INIS)

Hussein, Esam M.A.; Agbogun, H.M.D.; Al, Tom A.

2015-01-01

A method is presented for interpreting the values of x-ray attenuation coefficients reconstructed in computed tomography of porous media, while overcoming the ambiguity caused by the multichromatic nature of x-rays, dilution by void, and material heterogeneity. The method enables determination of porosity without relying on calibration or image segmentation or thresholding to discriminate pores from solid material. It distinguishes between solution-accessible and inaccessible pores, and provides the spatial and frequency distributions of solid-matrix material in a heterogeneous medium. This is accomplished by matching an image of a sample saturated with a contrast solution with that saturated with a transparent solution. Voxels occupied with solid-material and inaccessible pores are identified by the fact that they maintain the same location and image attributes in both images, with voxels containing inaccessible pores appearing empty in both images. Fully porous and accessible voxels exhibit the maximum contrast, while the rest are porous voxels containing mixtures of pore solutions and solid. This matching process is performed with an image registration computer code, and image processing software that requires only simple subtraction and multiplication (scaling) processes. The process is demonstrated in dolomite (non-uniform void distribution, homogeneous solid matrix) and sandstone (nearly uniform void distribution, heterogeneous solid matrix) samples, and its overall performance is shown to compare favorably with a method based on calibration and thresholding. - Highlights: • A method is presented for quantifying x-ray CT data for porous media. • The method neither requires calibration nor segmentation nor thresholding. • We use voxel matching between images of a sample saturated with two distinct solutions. • Method is demonstrated for micro-CT images of dolomite and sandstone samples. • Overall performance compares favorably with a calibration

Correlating Gas Transport Parameters and X-ray Computed Tomography Measurements in Porous Media

DEFF Research Database (Denmark)

Naveed, Muhammad; Hamamoto, Shoichiro; Kawamoto, Ken

2013-01-01

physical processes. The objective of this study was to characterize the relationships between gas transport parameters and soil-pore geometry revealed by X-ray CT. Sands of different shapes with a mean particle diameter (d50) ranging from 0.19 to 1.51 mm were used as porous media under both air...... was found between α and tortuosity calculated from gas transport parameters (Equation (Uncited) Image Tools), indicating that gas dispersivity has a linear and inverse relationship with gas diffusivity. A linear relationship was also found between ka and d50/TUMS2, indicating a strong dependency of ka...

Phytoremediated marine sediments as suitable peat-free growing media for production of red robin photinia (Photinia x fraseri).

Science.gov (United States)

Mattei, Paola; Gnesini, Alessandro; Gonnelli, Cristina; Marraccini, Chiara; Masciandaro, Grazia; Macci, Cristina; Doni, Serena; Iannelli, Renato; Lucchetti, Stefano; Nicese, Francesco P; Renella, Giancarlo

2018-06-01

Sediments dredged by an industrial port, slightly contaminated by heavy metals and petroleoum hydrocarbons, were phytoremediated and used as peat-free growing media for the red robin photinia (Photinia x fraseri L.). Plants were grown on sediment only (S), sediment mixed with composted pruning residues (S + PR), sediment fertilized with controlled release fertilizers (S + F) and peat-based growing media as control (C). Plant elongation and dry weight, leaf contents of chlorophyll, malondialdehyde (MDA), macronutrients and heavy metals were determined at the end of one growing season. Environmental impact related to the use of sediment-based as compared to peat-based growing media was assessed by the Life Cycle Analysis (LCA). Sediment-based growing media presented significantly higher bulk density, pH and electrical conductivity values, lower C and N contents, and significantly higher total and available P. Red robin photinia grown on S + F growing media showed morphological and chemical parameters similar to those of control plants (C), whereas plants grown on S and S + PR showed lower growth. Leaf concentration of nutrients and heavy metals varied depending on the considered element and growing media, but were all within the common values for ornamental plants, whereas the highest MDA concentrations were found in plants grown on traditional growing media. The LCA indicated the use of sediments as growing media reduced the C footprint of ornamental plant production and the contribute of growing media to the environmental impact per produced plant. We concluded that sediments phytoremediation and use in plant nursery is a practical alternative re-use option for dredged sediments. Copyright © 2018 Elsevier Ltd. All rights reserved.

Ion irradiation induced order-to-disorder transformations in δ-phase Sc4-xZr3+xO12+x/2

International Nuclear Information System (INIS)

Zhang, J.; Wang, Y.Q.; Tang, M.; Valdez, J.A.; Sickafus, K.E.

2010-01-01

The purpose of this study is to investigate the role of stoichiometry on crystal structure transformations in derivative fluorite compounds known as delta (δ) phase. In this study, polycrystalline δ-phase ceramic pellets were prepared with stoichiometries given by Sc 4-x Zr 3+x O 12+x/2 (x = 0, 0.77 and 1.20) . The pressed and polished pellets were then irradiated under cryogenic conditions with 200 keV Ne + ions to fluences ranging from 1-5 x 10 14 Ne/cm 2 . An order-to-disorder (O-D) transformation was observed for all compositions, as determined using grazing incidence X-ray diffraction (GIXRD). However, the transformation threshold dose was found to systematically decrease with increasing ZrO 2 content: ∼0.2, ∼0.16, and ∼0.08 dpa for Sc 4-x Zr 3+x O 12+x/2 with x = 0, 0.77, and 1.20, respectively. These irradiation-induced phase transformation results are discussed in terms of the crystal structure of the δ-phase.

PENGGUNAAN MEDIA PEMBELAJARAN DI MADRASAH ALIAH NEGERI SE-JAKARTA SELATAN

Directory of Open Access Journals (Sweden)

Rosita Primasari

2015-03-01

Full Text Available Penelitian ini bertujuan untuk memberikan informasi yang menggambarkan tentang penggunaan media pembelajaran yang digunakan oleh guru biologi dalam proses kegiatan belajar mengajar. Penelitian ini dilakukan di lima MAN yang ada di Jakarta Selatan. Metode penelitian yang digunakan adalah metode survei. Sampel penelitian ini berjumlah lima orang guru biologi dan 153 siswa kelas X. Hasil penelitian yang didapat bahwa media yang sering digunakan oleh guru di kelas pada pembelajaran biologi adalah ICT atau multimedia, media gambar diam, dan media gambar gerak, sedangkan media yang jarang digunakan adalah media relia dan film dengan suara. Guru mempertimbangkan karakteristik konsep biologi dalam menentukan media pembelajaran. Penelitian ini bertujuan untuk memberikan informasi yang menggambarkan tentang penggunaan media pembelajaran yang digunakan oleh guru biologi dalam proses kegiatan belajar mengajar. Penelitian ini dilakukan di lima MAN yang ada di Jakarta Selatan. Metode penelitian yang digunakan adalah metode survei. Sampel penelitian ini berjumlah lima orang guru biologi dan 153 siswa kelas X. Hasil penelitian yang didapat bahwa media yang sering digunakan oleh guru di kelas pada pembelajaran biologi adalah ICT atau multimedia, media gambar diam, dan media gambar gerak, sedangkan media yang jarang digunakan adalah media relia dan film dengan suara. Guru mempertimbangkan karakteristik konsep biologi dalam menentukan media pembelajaran. Normal 0 false false false IN X-NONE X-NONE

Window Selection Tool | Efficient Windows Collaborative

Science.gov (United States)

Louisville LA Lake Charles LA New Orleans LA Shreveport MA Boston MD Baltimore ME Portland MI Detroit MI Window Selection Tool will take you through a series of design conditions pertaining to your design and

Color Wheel Windows

Science.gov (United States)

Leonard, Stephanie

2012-01-01

In this article, the author describes a painting and drawing lesson which was inspired by the beautiful circular windows found in cathedrals and churches (also known as "rose windows"). This two-week lesson would reinforce both the concept of symmetry and students' understanding of the color wheel. (Contains 1 online resource.)

X window terminals in TRIUMF's central control system

International Nuclear Information System (INIS)

Kadantsev, S.G.; Kadantseva, T.P.; Davison, B.; Diel, D.A.; Grant, P.A.; Klassen, E.; Lee, K.S.; Mouat, M.M.; Richards, J.E.; Yogendran, P.J.

1994-08-01

TRIUMF's Central Control System is being upgraded. In this process, an environment that suits the needs of cyclotron operational use and the Controls Group's development and maintenance duties has been sought. Over the years since TRIUMF's inception, workstations and a variety of dedicated input/output devices have been introduced into the main console of the Control Room and into the offices of the Controls Group personnel. A number of factors including the overhead of system management, price/performance, time to obsolescence, flexibility, and reliability have affected the suitability of workstations and the other I/O devices. In the new configuration, a generic display device plays a very important role in the Central Control System. X terminals have proven to be superior to workstations and other display devices and are now the display medium of choice in TRIUMF's Controls Group. This paper reviews the TRIUMF Controls Group's experiences with X terminals. A number of aspects of X terminal use in a particle accelerator environment are discussed. Topics include functionality, hardware configuration, software management, relative cost, performance, reliability, boot mechanisms, application suitability, and operator acceptance. (author). 8 refs., 3 figs

Social Media Marketing: a Case Study of Company X

OpenAIRE

van der Zwaag, Janika

2014-01-01

During the last decade the usage of internet has increased tremendously. Today’s technology makes it possible to use the internet anytime and anywhere because of smartphones and other mobile devices. The growth in the usage of the internet has also increased the usage of social media, including the largest social media service, Facebook, which currently has more than 757 million daily active users. In recent years businesses are also increasingly utilising social media as a marketing tool...

Improved X-ray diagnosis of stomach by progress in the development of contrast media and examination techniques

International Nuclear Information System (INIS)

Lotz, W.

1982-01-01

Three factors have been responsible for the advances during the past few years in X-ray examination of the stomach: Improvement of the contrast media used; introduction of the rare-earth foils; and examination techniques imaging all sections of the stomach and of the duodenal bulb under hypotension in double-contrast technique, in complete filling, and imaging the accessible sections by means of proper compression. An interesting technique employs a combination of two different barium sulphate suspension used at the same time, e.g. Bubbly Barium or some other barium sulphate preparation with a small amount of High-Density Barium yielding excellent image of the gastric mucosa (technique with two contrast media). (orig.) [de

Resonant soft X-ray emission spectroscopy of liquids

International Nuclear Information System (INIS)

Guo, J.-H.; Augustsson, A.; Englund, C.-J.; Nordgren, J.

2004-01-01

We present now a possible way to carry out soft-x-ray fluorescence spectroscopy of liquids. The liquid cell has a window to attain compatibility with UHV conditions of the spectrometer and beamline. The synchrotron radiation enters the liquid cell through a 100nm-thick silicon nitride window and the emitted x-rays exit through the same window. This allows in particular liquid solid interfaces to be studied. Such a liquid cell has been used to study the electronic structure of a variety of systems ranging from water solutions of inorganic salts and inertial drugs to nano materials and actinide compounds in their wet conditions

X Power Tools

CERN Document Server

Tyler, Chris

2008-01-01

This book puts you in charge of the most flexible and adaptable graphical interface in the computer industry. The X Window System underlies graphical desktops on Linux and Unix systems, and supports advanced features of modern graphics cards. This unique inside look at X gives you a lot of useful ways to harness the power of this system effectively.

Skeletal deformations of newborn mice after X-ray exposure in fetal stage, with particular regard to hyperplastic growth phenomena in the neurocranium

Energy Technology Data Exchange (ETDEWEB)

Meyer, I.

1980-11-01

The following comprises a literary review of the effects of prenatal X-ray irradiation, known mainly from the mouse. Our own investigations were carried out with NMRI mice which on gestation days 11-13, 11-16 or 14-16 were exposed to whole-body irradiation comprising individual daily doses of between 80 and 160 R. All the examinations were carried out on the 18th day of gestation. Findings of special nature were ascertained on the talus and calcaneus. These bones indicate that the X-ray irradiation has an accelerating effect on development. It was possible to ascertain a corresponding effect with regard to the deformations of the os supraoccipital. After irradiation with 3 x 120 R and 3 x 160 R on the 11th-13th gestation days, both inhibitory deformities and also the occurence of an additional, novel bone anlage were observed. These findings were subjected to detailed histological examinations. In doing so, it was found that following a single irradiation with 200 R on the 12th day of gestation, 86,6% of the fetuses showed hyperostoses on the roof of the skull. In 13,2% of all cases there was in addition a clear, abnormal chondrification of the neurocranium, at the same time combined with an excessive formation of the bone, which protruded deep into the cerebral hemispheres. The patogeneses of this excessive growth phenomenon is explained on the basis of the complex relationship between the fetal brain formation and the formation of the skull cap.

X-ray beam generator

International Nuclear Information System (INIS)

Koller, T.J.; Randmer, J.A.

1977-01-01

A method of minimizing the preferential angular absorption of the divergent beam from an X-ray generator is described. The generator consists of an X-ray shielded housing with an X-ray transmissive window symmetrically placed in radial alignment with a focal spot area on a sloped target surface of an X-ray tube in the housing. The X-ray tube may be of the stationary anode type or of the rotating anode type. (U.K.)

46 CFR 160.054-3 - Construction.

Science.gov (United States)

2010-10-01

... 46 Shipping 6 2010-10-01 2010-10-01 false Construction. 160.054-3 Section 160.054-3 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) EQUIPMENT, CONSTRUCTION, AND MATERIALS... Construction. (a) Construction. The container shall be constructed of tough transparent material, not less than...

46 CFR 160.028-6 - Container.

Science.gov (United States)

2010-10-01

... 46 Shipping 6 2010-10-01 2010-10-01 false Container. 160.028-6 Section 160.028-6 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) EQUIPMENT, CONSTRUCTION, AND MATERIALS... Container. (a) General. Containers for the stowage of signal pistols and pistol projected parachute red...

Adaptive Liquid Crystal Windows

Energy Technology Data Exchange (ETDEWEB)

Taheri, Bahman; Bodnar, Volodymyr

2011-12-31

Energy consumption by private and commercial sectors in the U.S. has steadily grown over the last decade. The uncertainty in future availability of imported oil, on which the energy consumption relies strongly, resulted in a dramatic increase in the cost of energy. About 20% of this consumption are used to heat and cool houses and commercial buildings. To reduce dependence on the foreign oil and cut down emission of greenhouse gases, it is necessary to eliminate losses and reduce total energy consumption by buildings. To achieve this goal it is necessary to redefine the role of the conventional windows. At a minimum, windows should stop being a source for energy loss. Ideally, windows should become a source of energy, providing net gain to reduce energy used to heat and cool homes. It is possible to have a net energy gain from a window if its light transmission can be dynamically altered, ideally electronically without the need of operator assistance, providing optimal control of the solar gain that varies with season and climate in the U.S. In addition, the window must not require power from the building for operation. Resolution of this problem is a societal challenge and of national interest and will have a broad global impact. For this purpose, the year-round, allclimate window solution to provide an electronically variable solar heat gain coefficient (SHGC) with a wide dynamic range is needed. AlphaMicron, Inc. (AMI) developed and manufactured 1ft × 1ft prototype panels for the world’s first auto-adjusting Adaptive Liquid Crystal Windows (ALCWs) that can operate from sunlight without the need for external power source and demonstrate an electronically adjustable SHGC. This novel windows are based on AlphaMicron’s patented e-Tint® technology, a guesthost liquid crystal system implemented on flexible, optically clear plastic films. This technology is suitable both for OEM and aftermarket (retro-fitting) lamination to new and existing windows. Low level of

National Fenestration Rating Council (NFRC) | Efficient Windows

Science.gov (United States)

Collaborative Foundry Foundry New Construction Windows Window Selection Tool Selection Process Design Guidance Installation Replacement Windows Window Selection Tool Assessing Options Selection Process Design Guidance Installation Understanding Windows Benefits Design Considerations Measuring

On the Responsible Use of Communication Media for Learning

Science.gov (United States)

Yeaman, Andrew R. J.

2009-01-01

Just as Bob Heinich states that technology makes instruction visible (1970, 1971), putting the professional ethics into practice makes technology visible. The window for social insight into teachers' professional field is open to a particular view at the present. There are learner questions surrounding the use of media which need answering and…

U-Factor (U-value) | Efficient Windows Collaborative

Science.gov (United States)

Foundry Foundry New Construction Windows Window Selection Tool Selection Process Design Guidance Installation Replacement Windows Window Selection Tool Assessing Options Selection Process Design Guidance Installation Understanding Windows Benefits Design Considerations Measuring Performance Performance Standards

Thermodynamic properties of peptide solutions 20. Partial molar volumes and isothermal compressions for some tripeptides of sequence gly-X-gly (X = gly, ala, leu, asn, thr, and tyr) in aqueous solution at T = 298.15 K and p = (10–120) MPa

International Nuclear Information System (INIS)

Hedwig, Gavin R.; Høiland, Harald

2016-01-01

Highlights: • Sound speeds were measured for aqueous solutions of some tripeptides at high pressures. • Partial molar volumes and isothermal compressions were derived for T = 298.15 K and p = (10–120) MPa. • The partial molar volumes for non-polar amino acid side-chains decrease with increasing pressure. • The partial molar volumes for polar side-chains do not change significantly with increasing pressure. - Abstract: Sound speeds have been measured for aqueous solutions of six tripeptides of sequence glycyl-X-glycine, where X is one of the amino acids glycine, alanine, leucine, asparagine, threonine, and tyrosine at T = 298.15 K and at the pressures p = (10, 20, 40, 60, 80, 100, and 120) MPa. Using methods described in previous work, these sound speeds were used to derive the partial molar volumes at infinite dilution, V_2"o, the partial molar isentropic compressions at infinite dilution, K_S_,_2"o, and the partial molar isothermal compressions at infinite dilution, K"o_T_,_2 {K"o_T_,_2 = −(∂V_2"o/∂p)_T}, for the tripeptides in aqueous solution at the elevated pressures. The results were used to calculate the partial molar volumes and partial molar isothermal compressions for the various amino acid side-chains over the pressure range p = (10–120) MPa.

Right-to-left-shunt detected by c-TCD using the orbital window in comparison with temporal bone windows.

Science.gov (United States)

Kobayashi, Kazuto; Kimura, Kazumi; Iguchi, Yasuyuki; Sakai, Kenichirou; Aoki, Junya; Iwanaga, Takeshi; Shibazaki, Kensaku

2012-01-01

There have been some reports on right-to-left shunt as a cause of cryptogenic stroke. Although contrast transcranial Doppler (c-TCD) can detect RLS, an insufficient temporal window has occasionally restricted its applicability. Thus, we compared the rates of detecting RLS among temporal windows for the middle cerebral arteries (MCAs) and the orbital window for the internal carotid artery (ICA) on c-TCD. We used c-TCD to detect RLS in patients with suspected ischemic stroke. We enrolled patients who had both sufficient bilateral temporal windows for MCAs and a right orbital window for ICA and performed c-TCD using all three windows simultaneously. We enrolled 106 consecutive patients and identified microembolic signals (MES) in 30 (28%) of them. Among these 30 patients, 15 had MES from all 3 windows. When these 30 patients were defined as being positive for RLS, the rates of detection were 67%, 73%, and 80% from the right temporal, left temporal, and right orbital windows, respectively (P= .795). The right orbital window as well as the temporal window for c-TCD could detect RLS. Insonation from the orbital window should be useful for patients who lack temporal windows. Copyright © 2010 by the American Society of Neuroimaging.

SPITZER 70/160 μm OBSERVATIONS OF HIGH-REDSHIFT ULIRGs AND HyLIRGs IN THE BOOeTES FIELD

International Nuclear Information System (INIS)

Tyler, Krystal D.; Floc'h, Emeric Le; Rieke, George H.; Papovich, Casey; Blaylock, Myra; Dey, Arjun; Jannuzi, Buell T.; Armus, Lee; Desai, Vandana; Brand, Kate; Borys, Colin; Dole, Herve; Brown, Michael J. I.; Higdon, Sarah J. U.; Higdon, James L.; Charmandaris, Vassilis; Ashby, Matthew L. N.; Smith, Howard A.

2009-01-01

We present new 70 and 160 μm observations of a sample of extremely red (R - [24] ∼> 15 mag), mid-infrared bright, high-redshift (1.7 ∼ bol ∼ 4 x 10 12 L sun to ∼3 x 10 13 L sun (ULIRGs/hyper-luminous IR galaxies (HyLIRGs)), representing the first robust constraints on L bol for this class of object.

The X-Files: Investigating Alien Performance in a Thin-client World

OpenAIRE

Gunther, Neil J.

2000-01-01

Many scientific applications use the X11 window environment; an open source windows GUI standard employing a client/server architecture. X11 promotes: distributed computing, thin-client functionality, cheap desktop displays, compatibility with heterogeneous servers, remote services and administration, and greater maturity than newer web technologies. This paper details the author's investigations into close encounters with alien performance in X11-based seismic applications running on a 200-n...

40 CFR 40.160-2 - Financial status report.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 1 2010-07-01 2010-07-01 false Financial status report. 40.160-2 Section 40.160-2 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY GRANTS AND OTHER FEDERAL ASSISTANCE RESEARCH AND DEMONSTRATION GRANTS § 40.160-2 Financial status report. A financial status report...

41 CFR 105-8.160 - Communications.

Science.gov (United States)

2010-07-01

... 41 Public Contracts and Property Management 3 2010-07-01 2010-07-01 false Communications. 105-8.160 Section 105-8.160 Public Contracts and Property Management Federal Property Management Regulations... would result in a fundamental alteration in the nature of a program or activity or in undue financial...

21 CFR 211.160 - General requirements.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 4 2010-04-01 2010-04-01 false General requirements. 211.160 Section 211.160 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) DRUGS..., drug product container, or closure that is subject to deterioration. (2) Determination of conformance...

On the measurement of austenite in supermartensitic stainless steel by X-ray diffraction

Energy Technology Data Exchange (ETDEWEB)

Tolchard, Julian Richard, E-mail: tolchard@material.ntnu.no [Department of Materials Science and Engineering, Norwegian University of Science and Technology, Trondheim (Norway); Sømme, Astri; Solberg, Jan Ketil [Department of Materials Science and Engineering, Norwegian University of Science and Technology, Trondheim (Norway); Solheim, Karl Gunnar [Statoil, Stavanger (Norway)

2015-01-15

Sections of a 13Cr supermartensitic stainless steel were investigated to determine the optimum sample preparation for measurement of the austenite content by X-ray diffraction. The surface of several samples was mechanically ground or polished using media of grit sizes in the range 1–120 μm. The strained surface layer was afterwards removed stepwise by electropolishing, and the austenite content measured at each step. It was found that any level of mechanical grinding or polishing results in a reduction of the measured austenite fraction relative to the true bulk value, and that coarser grinding media impart greater damage and greater reduction in the measured austenite content. The results thus highlight the importance of the electropolishing step in preparation of such samples, but suggest that the American Society for Testing and Materials standard E975-03 substantially overestimates the amount of material which needs to be removed to recover the true “bulk” content. - Highlights: • Quantitative Rietveld analysis of austenite/martensite ratio in supermartensitic stainless steels • Critical evaluation of sample preparation for residual austenite measurements by X-ray diffraction • Highlighting of the importance of electropolishing as a final preparation step.

Hybrid window layer for photovoltaic cells

Science.gov (United States)

Deng, Xunming

2010-02-23

A novel photovoltaic solar cell and method of making the same are disclosed. The solar cell includes: at least one absorber layer which could either be a lightly doped layer or an undoped layer, and at least a doped window-layers which comprise at least two sub-window-layers. The first sub-window-layer, which is next to the absorber-layer, is deposited to form desirable junction with the absorber-layer. The second sub-window-layer, which is next to the first sub-window-layer, but not in direct contact with the absorber-layer, is deposited in order to have transmission higher than the first-sub-window-layer.

Windows PowerShell 20 Bible

CERN Document Server

Lee, Thomas; Schill, Mark E; Tanasovski, Tome

2011-01-01

Here's the complete guide to Windows PowerShell 2.0 for administrators and developers Windows PowerShell is Microsoft's next-generation scripting and automation language. This comprehensive volume provides the background that IT administrators and developers need in order to start using PowerShell automation in exciting new ways. It explains what PowerShell is, how to use the language, and specific ways to apply PowerShell in various technologies. Windows PowerShell is Microsoft's standard automation tool and something that every Windows administrator will eventually have to understand; this b

Mastering Microsoft Windows Server 2008 R2

CERN Document Server

Minasi, Mark; Finn, Aidan

2010-01-01

The one book you absolutely need to get up and running with Windows Server 2008 R2. One of the world's leading Windows authorities and top-selling author Mark Minasi explores every nook and cranny of the latest version of Microsoft's flagship network operating system, Windows Server 2008 R2, giving you the most in-depth coverage in any book on the market.: Focuses on Windows Windows Server 2008 R2, the newest version of Microsoft's Windows' server line of operating system, and the ideal server for new Windows 7 clients; Author Mark Minasi is one of the world's leading Windows authorities and h

Schematic Window Methodology Project

Data.gov (United States)

National Aeronautics and Space Administration — The aim of this IRAD is to produce a generic launch window analyzer (SWM) that allows for large-scale rapid analysis of a launch window and orbit design trade space....

7 CFR 160.8 - Steam distilled wood turpentine.

Science.gov (United States)

2010-01-01

... 7 Agriculture 3 2010-01-01 2010-01-01 false Steam distilled wood turpentine. 160.8 Section 160.8... STANDARDS FOR NAVAL STORES General § 160.8 Steam distilled wood turpentine. The designation “steam distilled wood turpentine” shall refer to the kind of spirits of turpentine obtained by steam distillation from...

Windows 7 resource kit

CERN Document Server

Northrup, Tony; Honeycutt, Jerry; Wilson, Ed

2009-01-01

In-depth and comprehensive, this RESOURCE KIT delivers the information you need to administer your Windows 7 system. You get authoritative technical guidance from those who know the technology best-Microsoft Most Valuable Professionals (MVPs) and the Windows 7 product team-along with essential scripts and resources. In addition, "Direct from the Source" sidebars offer deep insights and troubleshooting tips from the Windows 7 team. Get expert guidance on how to: Use Microsoft Deployment Toolkit best practices and tools. Plan user-state migration and test application compatibility.

The Efficient Windows Collaborative

Energy Technology Data Exchange (ETDEWEB)

Petermann, Nils

2006-03-31

The Efficient Windows Collaborative (EWC) is a coalition of manufacturers, component suppliers, government agencies, research institutions, and others who partner to expand the market for energy efficient window products. Funded through a cooperative agreement with the U.S. Department of Energy, the EWC provides education, communication and outreach in order to transform the residential window market to 70% energy efficient products by 2005. Implementation of the EWC is managed by the Alliance to Save Energy, with support from the University of Minnesota and Lawrence Berkeley National Laboratory.

Pemanfaatan Media Pembelajaran Audio Visual Untuk Meningkatkan Hasil Belajar PAI Pada Siswa Kelas V SDN Kalianget Timur X

Directory of Open Access Journals (Sweden)

Ernawati Ernawati

2014-08-01

Full Text Available Proses belajar mengajar pada hakikatnya adalah proses komunikasi, penyampaian pesan dari pengantar ke penerima. Pesan berupa isi/ajaran yang dituangkan ke dalam simbol-simbol komunikasi baik verbal maupun non verbal.Dalam pembelajaran PAI, agar bahan pelajaran yang diberikan lebih mudah dipahami oleh siswa, diperlukan media yang membantu proses penyampaian tersebut.Melalui media (alat bantu, diharapkan akan terjadi persepsi yang sama antara guru dan siswa. Apalagi Pendidikan Agama Islam yakni pendidikan yang sangat penting bagi kehidupan manusia, terutama dalam mencapai ketentraman bathin dan kesehatan mental padaumumnya.Media CD ini bisa digunakan sebagai salah satu alternatif pembelajaran PAI, khususnya pada materi “menceritakan kisah-kisah Nabi”.Melalui film tentang kisah Nabi yang ada dalam kaset CD, tentunya siswa akan lebih mudah memahami dan lebih mengasyikkan untuk digunakan sebagai sarana belajar daripada menggunakan buku ajar biasa yang pada akhirnya berpengaruh terhadap pencapaian hasil belajar siswa. Tujuan yang ingin dicapai melaluipenelitian ini adalah untuk mengetahui keefektifan media CD dalam meningkatkan hasil belajar siswa pada pelajaran PAI materi menceritakan kisah Nabi di kelas V SDN Kalianget Timur X.Berdasarkan hasil yang diperoleh dari siklus I sampai II, pemanfaatan media pembelajaran CD pada materi menceritakan kisah Nabi terbukti dapat meningkatkan hasil belajar siswa. Hal ini terbukti dengan adanya peningkatan hasil belajar baik secara kelompok maupun secara individu. Pemanfaatan media pembelajaran CDjuga dapat meningkatkan aktivitas belajar siswa yang meliputi keaktifan, kerjasama, keberanian, kedisiplinan, serta ketelitian siswa.

21 CFR 160.110 - Frozen eggs.

Science.gov (United States)

2010-04-01

... Frozen eggs. (a) Frozen eggs, frozen whole eggs, frozen mixed eggs is the food prepared by freezing... 21 Food and Drugs 2 2010-04-01 2010-04-01 false Frozen eggs. 160.110 Section 160.110 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR HUMAN...

46 CFR 160.021-6 - Container.

Science.gov (United States)

2010-10-01

... respect. Open the container, remove the contents, insert colored blotting paper as a lining, re-close... additional marking which might cause confusion as to the contents shall be permitted. The vessel's name... 46 Shipping 6 2010-10-01 2010-10-01 false Container. 160.021-6 Section 160.021-6 Shipping COAST...

Composition of 12-18th century window glass in Belgium: Non-figurative windows in secular buildings and stained-glass windows in religious buildings

International Nuclear Information System (INIS)

Schalm, Olivier; Janssens, Koen; Wouters, Hilde; Caluwe, Danielle

2007-01-01

A set of ca. 500 window glass fragments originating from different historical sites in Belgium and covering the period 12 th -18 th century was analyzed by means of electron probe microanalysis. Most samples are archaeological finds deriving from non-figurative windows in secular buildings. However, the analyzed set also contains glass sampled from still existing non-figurative windows in secular buildings and stained-glass windows in religious buildings. A sudden compositional change at the end of the 14 th century can be noticed among the series of glass compositions that were obtained. These changes could be related to the use of different glassmaker recipes and to the introduction of new raw materials for glass making

Composition of 12-18 th century window glass in Belgium: Non-figurative windows in secular buildings and stained-glass windows in religious buildings

Science.gov (United States)

Schalm, Olivier; Janssens, Koen; Wouters, Hilde; Caluwé, Danielle

2007-07-01

A set of ca. 500 window glass fragments originating from different historical sites in Belgium and covering the period 12 th-18 th century was analyzed by means of electron probe microanalysis. Most samples are archaeological finds deriving from non-figurative windows in secular buildings. However, the analyzed set also contains glass sampled from still existing non-figurative windows in secular buildings and stained-glass windows in religious buildings. A sudden compositional change at the end of the 14 th century can be noticed among the series of glass compositions that were obtained. These changes could be related to the use of different glassmaker recipes and to the introduction of new raw materials for glass making.

Assessment and forensic application of laser-induced breakdown spectroscopy (LIBS) for the discrimination of Australian window glass.

Science.gov (United States)

El-Deftar, Moteaa M; Speers, Naomi; Eggins, Stephen; Foster, Simon; Robertson, James; Lennard, Chris

2014-08-01

A commercially available laser-induced breakdown spectroscopy (LIBS) instrument was evaluated for the determination of elemental composition of twenty Australian window glass samples, consisting of 14 laminated samples and 6 non-laminated samples (or not otherwise specified) collected from broken windows at crime scenes. In this study, the LIBS figures of merit were assessed in terms of accuracy, limits of detection and precision using three standard reference materials (NIST 610, 612, and 1831). The discrimination potential of LIBS was compared to that obtained using laser ablation inductively coupled plasma mass spectrometry (LA-ICP-MS), X-ray microfluorescence spectroscopy (μXRF) and scanning electron microscopy energy dispersive X-ray spectrometry (SEM-EDX) for the analysis of architectural window glass samples collected from crime scenes in the Canberra region, Australia. Pairwise comparisons were performed using a three-sigma rule, two-way ANOVA and Tukey's HSD test at 95% confidence limit in order to investigate the discrimination power for window glass analysis. The results show that the elemental analysis of glass by LIBS provides a discrimination power greater than 97% (>98% when combined with refractive index data), which was comparable to the discrimination powers obtained by LA-ICP-MS and μXRF. These results indicate that LIBS is a feasible alternative to the more expensive LA-ICP-MS and μXRF options for the routine forensic analysis of window glass samples. Copyright © 2014 Elsevier Ireland Ltd. All rights reserved.

Development of nuclear reaction data retrieval system on Meme media

International Nuclear Information System (INIS)

Ohbayasi, Yosihide; Masui, Hiroshi; Aoyama, Shigeyoshi; Kato, Kiyoshi; Chiba, Masaki

2000-01-01

A newly designed retrieval system of charged particle nuclear reaction data is developed on Meme media architecture. We designed the network-based (client-server) retrieval system. The server system is constructed on a UNIX workstation with a relational database, and the client system is constructed on Microsoft Windows PC using an IntelligentPad software package. The IntelligentPad is currently available as developing Meme media. We will develop the system to realize effective utilization of nuclear reaction data: I. 'Re-production, Re-edit, Re-use', II. 'Circulation, Coordination and Evolution', III. 'Knowledge discovery'. (author)

Optical studies of massive X-ray binaries

International Nuclear Information System (INIS)

Zuiderwijk, E.J.

1979-01-01

Photometric and spectroscopic studies of several optical counterparts of massive X-ray binaries are presented. Subjects of study were the binary systems:HD77581/4U0900-40 (Vela X-1), HD153919/4U1700-37, Wray 977/4U1223-62 and Sk160/4U0115-74 (=SMC X-1). (Auth.)

Windows 7 The Missing Manual

CERN Document Server

Pogue, David

2010-01-01

In early reviews, geeks raved about Windows 7. But if you're an ordinary mortal, learning what this new system is all about will be challenging. Fear not: David Pogue's Windows 7: The Missing Manual comes to the rescue. Like its predecessors, this book illuminates its subject with reader-friendly insight, plenty of wit, and hardnosed objectivity for beginners as well as veteran PC users. Windows 7 fixes many of Vista's most painful shortcomings. It's speedier, has fewer intrusive and nagging screens, and is more compatible with peripherals. Plus, Windows 7 introduces a slew of new features,

Microsoft Windows Operating System Essentials

CERN Document Server

Carpenter, Tom

2012-01-01

A full-color guide to key Windows 7 administration concepts and topics Windows 7 is the leading desktop software, yet it can be a difficult concept to grasp, especially for those new to the field of IT. Microsoft Windows Operating System Essentials is an ideal resource for anyone new to computer administration and looking for a career in computers. Delving into areas such as fundamental Windows 7 administration concepts and various desktop OS topics, this full-color book addresses the skills necessary for individuals looking to break into a career in IT. Each chapter begins with a list of topi

Improved Windows for Cold Climates

DEFF Research Database (Denmark)

Laustsen, Jacob Birck; Svendsen, Svend

2005-01-01

considerably by reducing the frame width, which results in a larger transparent area causing a larger solar gain but still main-taining a low thermal transmittance. Using three layers of glass with large gaps, using very slim frame profiles, and omitting the edge constructions that normally causes thermal...... windows with improved energy performance. Traditionally evaluation of the energy performance of windows has focused on the thermal transmittance, but as windows differ from the rest of the building envelope by allowing solar energy to enter the building, the total solar energy transmittance is equally...... important. In the heating season in cold climates the solar gain through windows can be utilized for space heating which results in a corresponding reduction in the energy production that is often based on fossil fuels. A suitable quantity for evaluating the energy performance of windows in a simple...