WorldWideScience

Sample records for wind vector place

  1. Hurricane Wind Vector Estimates from WindSat Polarimetric Radiometer

    National Research Council Canada - National Science Library

    Adams, Ian S; Hennon, Christopther C; Jones, W. L; Ahmad, Khalil

    2005-01-01

    .... In late 2004, the first preliminary oceanic wind vector results were released, and this paper presents the first evaluation of this product for several Atlantic hurricanes during the 2003 season...

  2. Vector wind and vector wind shear models 0 to 27 km altitude for Cape Kennedy, Florida, and Vandenberg AFB, California

    Science.gov (United States)

    Smith, O. E.

    1976-01-01

    The techniques are presented to derive several statistical wind models. The techniques are from the properties of the multivariate normal probability function. Assuming that the winds can be considered as bivariate normally distributed, then (1) the wind components and conditional wind components are univariate normally distributed, (2) the wind speed is Rayleigh distributed, (3) the conditional distribution of wind speed given a wind direction is Rayleigh distributed, and (4) the frequency of wind direction can be derived. All of these distributions are derived from the 5-sample parameter of wind for the bivariate normal distribution. By further assuming that the winds at two altitudes are quadravariate normally distributed, then the vector wind shear is bivariate normally distributed and the modulus of the vector wind shear is Rayleigh distributed. The conditional probability of wind component shears given a wind component is normally distributed. Examples of these and other properties of the multivariate normal probability distribution function as applied to Cape Kennedy, Florida, and Vandenberg AFB, California, wind data samples are given. A technique to develop a synthetic vector wind profile model of interest to aerospace vehicle applications is presented.

  3. Optimal Placing of Wind Turbines: Modelling the Uncertainty

    NARCIS (Netherlands)

    Leenman, T.S.; Phillipson, F.

    2015-01-01

    When looking at the optimal place to locate a wind turbine, trade-offs have to be made between local placement and spreading: transmission loss favours local placements and the correlation between the stochastic productions of wind turbines favours spreading. In this paper steps are described to

  4. Optimal Placing of Wind Turbines: Modelling the Uncertainty

    NARCIS (Netherlands)

    Leenman, T.S.; Phillipson, F.

    2014-01-01

    When looking at the optimal place to locate a wind turbine, trade-offs have to be made between local placement and spreading: transmission loss favours local placements and the correlation between the stochastic productions of wind turbines favours spreading. In this paper steps are described to

  5. Impact of Scatterometer Ocean Wind Vector Data on NOAA Operations

    Science.gov (United States)

    Jelenak, Z.; Chang, P.; Brennan, M. J.; Sienkiewicz, J. M.

    2015-12-01

    Near real-time measurements of ocean surface vector winds (OSVW), including both wind speed and direction from non-NOAA satellites, are being widely used in critical operational NOAA forecasting and warning activities. The scatterometer wind data data have had major operational impact in: a) determining wind warning areas for mid-latitude systems (gale, storm,hurricane force); b) determining tropical cyclone 34-knot and 50-knot wind radii. c) tracking the center location of tropical cyclones, including the initial identification of their formation. d) identifying and warning of extreme gap and jet wind events at all latitudes. e) identifying the current location of frontal systems and high and low pressure centers. f) improving coastal surf and swell forecasts Much has been learned about the importance and utility of satellite OSVW data in operational weather forecasting and warning by exploiting OSVW research satellites in near real-time. Since December 1999 when first data from QuikSCAT scatterometer became available in near real time NOAA operations have been benefiting from ASCAT scatterometer observations on MetOp-A and B, Indian OSCAT scatterometer on OceanSat-3 and lately NASA's RapidScat mission on International Space Station. With oceans comprising over 70 percent of the earth's surface, the impacts of these data have been tremendous in serving society's needs for weather and water information and in supporting the nation's commerce with information for safe, efficient, and environmentally sound transportation and coastal preparedness. The satellite OSVW experience that has been gained over the past decade by users in the operational weather community allows for realistic operational OSVW requirements to be properly stated for future missions. Successful model of transitioning research data into operation implemented by Ocean Winds Team in NOAA's NESDIS/STAR office and subsequent data impacts will be presented and discussed.

  6. Blended 6-Hourly Sea Surface Wind Vectors and Wind Stress on a Global 0.25 Degree Grid (1987-2011)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — The Blended Global Sea Surface Winds products contain ocean surface wind vectors and wind stress on a global 0.25 degree grid, in multiple time resolutions of...

  7. Vector control of wind turbine on the basis of the fuzzy selective neural net*

    Science.gov (United States)

    Engel, E. A.; Kovalev, I. V.; Engel, N. E.

    2016-04-01

    An article describes vector control of wind turbine based on fuzzy selective neural net. Based on the wind turbine system’s state, the fuzzy selective neural net tracks an maximum power point under random perturbations. Numerical simulations are accomplished to clarify the applicability and advantages of the proposed vector wind turbine’s control on the basis of the fuzzy selective neuronet. The simulation results show that the proposed intelligent control of wind turbine achieves real-time control speed and competitive performance, as compared to a classical control model with PID controllers based on traditional maximum torque control strategy.

  8. A Novel Empirical Mode Decomposition With Support Vector Regression for Wind Speed Forecasting.

    Science.gov (United States)

    Ren, Ye; Suganthan, Ponnuthurai Nagaratnam; Srikanth, Narasimalu

    2016-08-01

    Wind energy is a clean and an abundant renewable energy source. Accurate wind speed forecasting is essential for power dispatch planning, unit commitment decision, maintenance scheduling, and regulation. However, wind is intermittent and wind speed is difficult to predict. This brief proposes a novel wind speed forecasting method by integrating empirical mode decomposition (EMD) and support vector regression (SVR) methods. The EMD is used to decompose the wind speed time series into several intrinsic mode functions (IMFs) and a residue. Subsequently, a vector combining one historical data from each IMF and the residue is generated to train the SVR. The proposed EMD-SVR model is evaluated with a wind speed data set. The proposed EMD-SVR model outperforms several recently reported methods with respect to accuracy or computational complexity.

  9. A Novel Integrated Algorithm for Wind Vector Retrieval from Conically Scanning Scatterometers

    Directory of Open Access Journals (Sweden)

    Xuetong Xie

    2013-11-01

    Full Text Available Due to the lower efficiency and the larger wind direction error of traditional algorithms, a novel integrated wind retrieval algorithm is proposed for conically scanning scatterometers. The proposed algorithm has the dual advantages of less computational cost and higher wind direction retrieval accuracy by integrating the wind speed standard deviation (WSSD algorithm and the wind direction interval retrieval (DIR algorithm. It adopts wind speed standard deviation as a criterion for searching possible wind vector solutions and retrieving a potential wind direction interval based on the change rate of the wind speed standard deviation. Moreover, a modified three-step ambiguity removal method is designed to let more wind directions be selected in the process of nudging and filtering. The performance of the new algorithm is illustrated by retrieval experiments using 300 orbits of SeaWinds/QuikSCAT L2A data (backscatter coefficients at 25 km resolution and co-located buoy data. Experimental results indicate that the new algorithm can evidently enhance the wind direction retrieval accuracy, especially in the nadir region. In comparison with the SeaWinds L2B Version 2 25 km selected wind product (retrieved wind fields, an improvement of 5.1° in wind direction retrieval can be made by the new algorithm for that region.

  10. The right place for wind power. Part 1

    International Nuclear Information System (INIS)

    1999-01-01

    The aim of this report is to suggest criteria for siting of wind power plants against a background of the demand for a long-term care of land and water areas, as well as for conservation needs concerning environmental effects and landscape scenery. The criteria should be adapted to situations applicable to different regions in Sweden

  11. Estimation of the wind turbine yaw error by support vector machines

    DEFF Research Database (Denmark)

    Sheibat-Othman, Nida; Othman, Sami; Tayari, Raoaa

    2015-01-01

    Wind turbine yaw error information is of high importance in controlling wind turbine power and structural load. Normally used wind vanes are imprecise. In this work, the estimation of yaw error in wind turbines is studied using support vector machines for regression (SVR). As the methodology...... is data-based, simulated data from a high fidelity aero-elastic model is used for learning. The model simulates a variable speed horizontal-axis wind turbine composed of three blades and a full converter. Both partial load (blade angles fixed at 0 deg) and full load zones (active pitch actuators...

  12. Analysis of vector wind change with respect to time for Vandenberg Air Force Base, California

    Science.gov (United States)

    Adelfang, S. I.

    1978-01-01

    A statistical analysis of the temporal variability of wind vectors at 1 km altitude intervals from 0 to 27 km altitude taken from a 10-year data sample of twice-daily rawinsode wind measurements over Vandenberg Air Force Base, California is presented.

  13. Plants and ventifacts delineate late Holocene wind vectors in the Coachella Valley, USA

    Science.gov (United States)

    Griffiths, P.G.; Webb, R.H.; Fisher, M.; Muth, Allan

    2009-01-01

    Strong westerly winds that emanate from San Gorgonio Pass, the lowest point between Palm Springs and Los Angeles, California, dominate aeolian transport in the Coachella Valley of the western Sonoran Desert. These winds deposit sand in coppice dunes that are critical habitat for several species, including the state and federally listed threatened species Uma inornata, a lizard. Although wind directions are generally defined in this valley, the wind field has complex interactions with local topography and becomes more variable with distance from the pass. Local, dominant wind directions are preserved by growth patterns of Larrea tridentata (creosote bush), a shrub characteristic of the hot North American deserts, and ventifacts. Exceptionally long-lived, Larrea has the potential to preserve wind direction over centuries to millennia, shaped by the abrasive pruning of windward branches and the persistent training of leeward branches. Wind direction preserved in Larrea individuals and clones was mapped at 192 locations. Compared with wind data from three weather stations, Larrea vectors effectively reflect annual prevailing winds. Ventifacts measured at 24 locations record winds 10° more westerly than Larrea and appear to reflect the direction of the most erosive winds. Based on detailed mapping of local wind directions as preserved in Larrea, only the northern half of the Mission-Morongo Creek floodplain is likely to supply sand to protected U. inornata habitat in the Willow Hole ecological reserve.

  14. Alignment of stress, mean wind, and vertical gradient of the velocity vector

    DEFF Research Database (Denmark)

    Berg, Jacob; Mann, Jakob; Patton, E.G.

    2012-01-01

    In many applications in the atmospheric surface layer the turbulent-viscosity hypothesis is applied, i.e. the stress vector can be described through the vertical gradient of velocity. In the atmospheric surface layer, where the Coriolis force and baroclinic effects are considered negligible......, this is supposedly a good approximation. High resolution large-eddy simulation (LES) data show that it is indeed the case. Through analysis of WindCube lidar measurements accompanied by sonic measurements we show that this is, on the other hand, rarely the case in the real atmosphere. This might indicate that large...... of atmospheric boundary layer modeling. The measurements are from the Danish wind turbine test sites at Høvsøre. With theWindCube lidar we are able to reach heights of 250 meters and hence capture the entire atmospheric surface layer both in terms of wind speed and the direction of the mean stress vector....

  15. Short-interval SMS wind vector determinations for a severe local storms area

    Science.gov (United States)

    Peslen, C. A.

    1980-01-01

    Short-interval SMS-2 visible digital image data are used to derive wind vectors from cloud tracking on time-lapsed sequences of geosynchronous satellite images. The cloud tracking areas are located in the Central Plains, where on May 6, 1975 hail-producing thunderstorms occurred ahead of a well defined dry line. Cloud tracking is performed on the Goddard Space Flight Center Atmospheric and Oceanographic Information Processing System. Lower tropospheric cumulus tracers are selected with the assistance of a cloud-top height algorithm. Divergence is derived from the cloud motions using a modified Cressman (1959) objective analysis technique which is designed to organize irregularly spaced wind vectors into uniformly gridded wind fields. The results demonstrate the feasibility of using satellite-derived wind vectors and their associated divergence fields in describing the conditions preceding severe local storm development. For this case, an area of convergence appeared ahead of the dry line and coincided with the developing area of severe weather. The magnitude of the maximum convergence varied between -10 to the -5th and -10 to the -14th per sec. The number of satellite-derived wind vectors which were required to describe conditions of the low-level atmosphere was adequate before numerous cumulonimbus cells formed. This technique is limited in areas of advanced convection.

  16. Auto-correlation analysis of ocean surface wind vectors

    Indian Academy of Sciences (India)

    M. Senthilkumar (Newgen Imaging) 1461 1996 Oct 15 13:05:22

    time series data of surface winds measured in situ by a deep water buoy in the Indian Ocean has been carried out. ... A case study using the TRMM Microwave Imager (TMI) and ... parameter is essential when the values of the parameter ...

  17. High stability vector-based direct power control for DFIG-based wind turbine

    DEFF Research Database (Denmark)

    Zhu, Rongwu; Chen, Zhe; Wu, Xiaojie

    2015-01-01

    This paper proposes an improved vector-based direct power control (DPC) strategy for the doubly-fed induction generator (DFIG)-based wind energy conversion system. Based on the small signal model, the proposed DPC improves the stability of the DFIG, and avoids the DFIG operating in the marginal...

  18. Very-short-term wind power probabilistic forecasts by sparse vector autoregression

    DEFF Research Database (Denmark)

    Dowell, Jethro; Pinson, Pierre

    2016-01-01

    A spatio-temporal method for producing very-shortterm parametric probabilistic wind power forecasts at a large number of locations is presented. Smart grids containing tens, or hundreds, of wind generators require skilled very-short-term forecasts to operate effectively, and spatial information...... is highly desirable. In addition, probabilistic forecasts are widely regarded as necessary for optimal power system management as they quantify the uncertainty associated with point forecasts. Here we work within a parametric framework based on the logit-normal distribution and forecast its parameters....... The location parameter for multiple wind farms is modelled as a vector-valued spatiotemporal process, and the scale parameter is tracked by modified exponential smoothing. A state-of-the-art technique for fitting sparse vector autoregressive models is employed to model the location parameter and demonstrates...

  19. Gridded Calibration of Ensemble Wind Vector Forecasts Using Ensemble Model Output Statistics

    Science.gov (United States)

    Lazarus, S. M.; Holman, B. P.; Splitt, M. E.

    2017-12-01

    A computationally efficient method is developed that performs gridded post processing of ensemble wind vector forecasts. An expansive set of idealized WRF model simulations are generated to provide physically consistent high resolution winds over a coastal domain characterized by an intricate land / water mask. Ensemble model output statistics (EMOS) is used to calibrate the ensemble wind vector forecasts at observation locations. The local EMOS predictive parameters (mean and variance) are then spread throughout the grid utilizing flow-dependent statistical relationships extracted from the downscaled WRF winds. Using data withdrawal and 28 east central Florida stations, the method is applied to one year of 24 h wind forecasts from the Global Ensemble Forecast System (GEFS). Compared to the raw GEFS, the approach improves both the deterministic and probabilistic forecast skill. Analysis of multivariate rank histograms indicate the post processed forecasts are calibrated. Two downscaling case studies are presented, a quiescent easterly flow event and a frontal passage. Strengths and weaknesses of the approach are presented and discussed.

  20. Short-Term Wind Speed Forecasting Using Support Vector Regression Optimized by Cuckoo Optimization Algorithm

    Directory of Open Access Journals (Sweden)

    Jianzhou Wang

    2015-01-01

    Full Text Available This paper develops an effectively intelligent model to forecast short-term wind speed series. A hybrid forecasting technique is proposed based on recurrence plot (RP and optimized support vector regression (SVR. Wind caused by the interaction of meteorological systems makes itself extremely unsteady and difficult to forecast. To understand the wind system, the wind speed series is analyzed using RP. Then, the SVR model is employed to forecast wind speed, in which the input variables are selected by RP, and two crucial parameters, including the penalties factor and gamma of the kernel function RBF, are optimized by various optimization algorithms. Those optimized algorithms are genetic algorithm (GA, particle swarm optimization algorithm (PSO, and cuckoo optimization algorithm (COA. Finally, the optimized SVR models, including COA-SVR, PSO-SVR, and GA-SVR, are evaluated based on some criteria and a hypothesis test. The experimental results show that (1 analysis of RP reveals that wind speed has short-term predictability on a short-term time scale, (2 the performance of the COA-SVR model is superior to that of the PSO-SVR and GA-SVR methods, especially for the jumping samplings, and (3 the COA-SVR method is statistically robust in multi-step-ahead prediction and can be applied to practical wind farm applications.

  1. Visiting places to see wind turbines. America and England edition; Fusha mitearuki. America, Igirisu hen

    Energy Technology Data Exchange (ETDEWEB)

    Okada, H.

    1996-09-01

    This paper introduces what were seen when visits were made in America and England to find and see wind power generators that can be used as an outdoor power supply for amateur radio operators. Visits were made to the Ames school town near Des Moines, Iowa, radio ham shops and World Power Technologies Corporation in Minneapolis, Minnesota, and Windstream Power System Corporation in Burlington, Vermont. Other manufacturers included NRG System Corporation, Atlantic Orient Corporation, and The New World Power Technology Corporation. Items of information, data and materials on small power wind generators were collected at each place visited. In England, a boat using a battery charger driven by a wind power generator made by VLM Corporation was inspected at a yacht harbor in Portsmouth, 100 km south-west of London. Other visits included LUMIC Corporation, a micro wind power generator manufacturer in Poole of the south coast, Kirmarnock, a maker of micro wind turbines and generators, and Proven Engineering Corporation in Glasgow, a manufacturer of wind power generators. 4 figs.

  2. Fault diagnosis of direct-drive wind turbine based on support vector machine

    International Nuclear Information System (INIS)

    An, X L; Jiang, D X; Li, S H; Chen, J

    2011-01-01

    A fault diagnosis method of direct-drive wind turbine based on support vector machine (SVM) and feature selection is presented. The time-domain feature parameters of main shaft vibration signal in the horizontal and vertical directions are considered in the method. Firstly, in laboratory scale five experiments of direct-drive wind turbine with normal condition, wind wheel mass imbalance fault, wind wheel aerodynamic imbalance fault, yaw fault and blade airfoil change fault are carried out. The features of five experiments are analyzed. Secondly, the sensitive time-domain feature parameters in the horizontal and vertical directions of vibration signal in the five conditions are selected and used as feature samples. By training, the mapping relation between feature parameters and fault types are established in SVM model. Finally, the performance of the proposed method is verified through experimental data. The results show that the proposed method is effective in identifying the fault of wind turbine. It has good classification ability and robustness to diagnose the fault of direct-drive wind turbine.

  3. Fine tuning support vector machines for short-term wind speed forecasting

    International Nuclear Information System (INIS)

    Zhou Junyi; Shi Jing; Li Gong

    2011-01-01

    Research highlights: → A systematic approach to tuning SVM models for wind speed prediction is proposed. → Multiple kernel functions and a wide range of tuning parameters are evaluated, and optimal parameters for each kernel function are obtained. → It is found that the forecasting performance of SVM is closely related to the dynamic characteristics of wind speed. → Under the optimal combination of parameters, different kernels give comparable forecasting accuracy. -- Abstract: Accurate forecasting of wind speed is critical to the effective harvesting of wind energy and the integration of wind power into the existing electric power grid. Least-squares support vector machines (LS-SVM), a powerful technique that is widely applied in a variety of classification and function estimation problems, carries great potential for the application of short-term wind speed forecasting. In this case, tuning the model parameters for optimal forecasting accuracy is a fundamental issue. This paper, for the first time, presents a systematic study on fine tuning of LS-SVM model parameters for one-step ahead wind speed forecasting. Three SVM kernels, namely linear, Gaussian, and polynomial kernels, are implemented. The SVM parameters considered include the training sample size, SVM order, regularization parameter, and kernel parameters. The results show that (1) the performance of LS-SVM is closely related to the dynamic characteristics of wind speed; (2) all parameters investigated greatly affect the performance of LS-SVM models; (3) under the optimal combination of parameters after fine tuning, the three kernels give comparable forecasting accuracy; (4) the performance of linear kernel is worse than the other two kernels when the training sample size or SVM order is small. In addition, LS-SVMs are compared against the persistence approach, and it is found that they can outperform the persistence model in the majority of cases.

  4. Preliminary Investigation on Generation of Electricity Using Micro Wind Turbines Placed on A Car

    Directory of Open Access Journals (Sweden)

    Yogendra Chaudhary

    2017-03-01

    Full Text Available Wind energy is one of the prominent resources for renewable energy and it is traditionally extracted using stationary wind turbines. However, it can also be extracted using mini or micro wind turbines on a moving body, such as an automobile, while cruising at high speeds on freeways. If the electricity is produced using air flowing around the vehicle without affecting aerodynamic performance of the vehicle, it can be used to charge up the battery or power up additional accessories of the vehicle. For the first time, in the present work, a preliminary investigation was carried out to generate electricity by utilizing air flow on a moving car. Initially, a correlation between the car speed and wind velocity was established using an anemometer. Placing a set of two micro wind turbines along with two micro generators on the rear end of the car trunk, the present study investigated the feasibility of generating electricity from these micro wind turbines while evaluating the effect of drag force on the performance of the car through the experimental approach and computational fluid dynamics (CFD simulations. Both approaches confirmed negligible effect of drag force on the vehicle performance in terms of gas mileage and changes in drag coefficient values. Following these studies, the micro wind turbines were also tested for electricity generation at various cruising speeds of the car ranging from 50 to 80 mph on the freeways. The voltage and power generated always showed an increasing trend with increasing the car speed, however they saturated when a cut off limit was setup with the voltage controllers. A maximum voltage of 3.5 V and a maximum current of 0.8 A were generated by each micro wind turbine when a cut off limit was used along with a load consisting of four LED bulbs in parallel with 3.5 V and 0.2 A rating each. On the other hand, when the tests were repeated without using the cut-off limit, a maximum voltage of 18.91 V and a maximum current

  5. The Alignment of the Mean Wind and Stress Vectors in the Unstable Surface Layer

    Science.gov (United States)

    Bernardes, M.; Dias, N. L.

    2010-01-01

    A significant non-alignment between the mean horizontal wind vector and the stress vector was observed for turbulence measurements both above the water surface of a large lake, and over a land surface (soybean crop). Possible causes for this discrepancy such as flow distortion, averaging times and the procedure used for extracting the turbulent fluctuations (low-pass filtering and filter widths etc.), were dismissed after a detailed analysis. Minimum averaging times always less than 30 min were established by calculating ogives, and error bounds for the turbulent stresses were derived with three different approaches, based on integral time scales (first-crossing and lag-window estimates) and on a bootstrap technique. It was found that the mean absolute value of the angle between the mean wind and stress vectors is highly related to atmospheric stability, with the non-alignment increasing distinctively with increasing instability. Given a coordinate rotation that aligns the mean wind with the x direction, this behaviour can be explained by the growth of the relative error of the u- w component with instability. As a result, under more unstable conditions the u- w and the v- w components become of the same order of magnitude, and the local stress vector gives the impression of being non-aligned with the mean wind vector. The relative error of the v- w component is large enough to make it undistinguishable from zero throughout the range of stabilities. Therefore, the standard assumptions of Monin-Obukhov similarity theory hold: it is fair to assume that the v- w stress component is actually zero, and that the non-alignment is a purely statistical effect. An analysis of the dimensionless budgets of the u- w and the v- w components confirms this interpretation, with both shear and buoyant production of u- w decreasing with increasing instability. In the v- w budget, shear production is zero by definition, while buoyancy displays very low-intensity fluctuations around

  6. Current error vector based prediction control of the section winding permanent magnet linear synchronous motor

    Energy Technology Data Exchange (ETDEWEB)

    Hong Junjie, E-mail: hongjjie@mail.sysu.edu.cn [School of Engineering, Sun Yat-Sen University, Guangzhou 510006 (China); Li Liyi, E-mail: liliyi@hit.edu.cn [Dept. Electrical Engineering, Harbin Institute of Technology, Harbin 150000 (China); Zong Zhijian; Liu Zhongtu [School of Engineering, Sun Yat-Sen University, Guangzhou 510006 (China)

    2011-10-15

    Highlights: {yields} The structure of the permanent magnet linear synchronous motor (SW-PMLSM) is new. {yields} A new current control method CEVPC is employed in this motor. {yields} The sectional power supply method is different to the others and effective. {yields} The performance gets worse with voltage and current limitations. - Abstract: To include features such as greater thrust density, higher efficiency without reducing the thrust stability, this paper proposes a section winding permanent magnet linear synchronous motor (SW-PMLSM), whose iron core is continuous, whereas winding is divided. The discrete system model of the motor is derived. With the definition of the current error vector and selection of the value function, the theory of the current error vector based prediction control (CEVPC) for the motor currents is explained clearly. According to the winding section feature, the motion region of the mover is divided into five zones, in which the implementation of the current predictive control method is proposed. Finally, the experimental platform is constructed and experiments are carried out. The results show: the current control effect has good dynamic response, and the thrust on the mover remains constant basically.

  7. Aspects of the determination of winds by means of scatterometry and of the utilization of vector wind data for meteorological forecasts

    Science.gov (United States)

    Pierson, W. J., Jr.; Sylvester, W. B.; Donelan, M. A.

    1986-01-01

    The present paper provides a description of four aspects of scatterometer winds and their uses. The theory of wave generation by the wind is considered along with an analysis of the properties of superobservations, and studies of intermittent versus continuous data assimilation methods for numerical weather predictions which use remotely sensed data. A comparison of the sum of squares versus the maximum likelihood method for recovering the vector winds is also conducted. Questions regarding wind speed, friction velocity, or normal stress are discussed and synoptic scale fields from Seasat-SASS data are examined.

  8. Short-term wind speed prediction using an unscented Kalman filter based state-space support vector regression approach

    International Nuclear Information System (INIS)

    Chen, Kuilin; Yu, Jie

    2014-01-01

    Highlights: • A novel hybrid modeling method is proposed for short-term wind speed forecasting. • Support vector regression model is constructed to formulate nonlinear state-space framework. • Unscented Kalman filter is adopted to recursively update states under random uncertainty. • The new SVR–UKF approach is compared to several conventional methods for short-term wind speed prediction. • The proposed method demonstrates higher prediction accuracy and reliability. - Abstract: Accurate wind speed forecasting is becoming increasingly important to improve and optimize renewable wind power generation. Particularly, reliable short-term wind speed prediction can enable model predictive control of wind turbines and real-time optimization of wind farm operation. However, this task remains challenging due to the strong stochastic nature and dynamic uncertainty of wind speed. In this study, unscented Kalman filter (UKF) is integrated with support vector regression (SVR) based state-space model in order to precisely update the short-term estimation of wind speed sequence. In the proposed SVR–UKF approach, support vector regression is first employed to formulate a nonlinear state-space model and then unscented Kalman filter is adopted to perform dynamic state estimation recursively on wind sequence with stochastic uncertainty. The novel SVR–UKF method is compared with artificial neural networks (ANNs), SVR, autoregressive (AR) and autoregressive integrated with Kalman filter (AR-Kalman) approaches for predicting short-term wind speed sequences collected from three sites in Massachusetts, USA. The forecasting results indicate that the proposed method has much better performance in both one-step-ahead and multi-step-ahead wind speed predictions than the other approaches across all the locations

  9. NASA's GMAO Atmospheric Motion Vectors Simulator: Description and Application to the MISTiC Winds Concept

    Science.gov (United States)

    Carvalho, David; McCarty, Will; Errico, Ron; Prive, Nikki

    2018-01-01

    An atmospheric wind vectors (AMVs) simulator was developed by NASA's GMAO to simulate observations from future satellite constellation concepts. The synthetic AMVs can then be used in OSSEs to estimate and quantify the potential added value of new observations to the present Earth observing system and, ultimately, the expected impact on the current weather forecasting skill. The GMAO AMV simulator is a tunable and flexible computer code that is able to simulate AMVs expected to be derived from different instruments and satellite orbit configurations. As a case study and example of the usefulness of this tool, the GMAO AMV simulator was used to simulate AMVs envisioned to be provided by the MISTiC Winds, a NASA mission concept consisting of a constellation of satellites equipped with infrared spectral midwave spectrometers, expected to provide high spatial and temporal resolution temperature and humidity soundings of the troposphere that can be used to derive AMVs from the tracking of clouds and water vapor features. The GMAO AMV simulator identifies trackable clouds and water vapor features in the G5NR and employs a probabilistic function to draw a subset of the identified trackable features. Before the simulator is applied to the MISTiC Winds concept, the simulator was calibrated to yield realistic observations counts and spatial distributions and validated considering as a proxy instrument to the MISTiC Winds the Himawari-8 Advanced Imager (AHI). The simulated AHI AMVs showed a close match with the real AHI AMVs in terms of observation counts and spatial distributions, showing that the GMAO AMVs simulator synthesizes AMVs observations with enough quality and realism to produce a response from the DAS equivalent to the one produced with real observations. When applied to the MISTiC Winds scanning points, it can be expected that the MISTiC Winds will be able to collect approximately 60,000 wind observations every 6 hours, if considering a constellation composed of

  10. Time Series Analysis and Forecasting for Wind Speeds Using Support Vector Regression Coupled with Artificial Intelligent Algorithms

    Directory of Open Access Journals (Sweden)

    Ping Jiang

    2015-01-01

    Full Text Available Wind speed/power has received increasing attention around the earth due to its renewable nature as well as environmental friendliness. With the global installed wind power capacity rapidly increasing, wind industry is growing into a large-scale business. Reliable short-term wind speed forecasts play a practical and crucial role in wind energy conversion systems, such as the dynamic control of wind turbines and power system scheduling. In this paper, an intelligent hybrid model for short-term wind speed prediction is examined; the model is based on cross correlation (CC analysis and a support vector regression (SVR model that is coupled with brainstorm optimization (BSO and cuckoo search (CS algorithms, which are successfully utilized for parameter determination. The proposed hybrid models were used to forecast short-term wind speeds collected from four wind turbines located on a wind farm in China. The forecasting results demonstrate that the intelligent hybrid models outperform single models for short-term wind speed forecasting, which mainly results from the superiority of BSO and CS for parameter optimization.

  11. Vectors

    DEFF Research Database (Denmark)

    Boeriis, Morten; van Leeuwen, Theo

    2017-01-01

    should be taken into account in discussing ‘reactions’, which Kress and van Leeuwen link only to eyeline vectors. Finally, the question can be raised as to whether actions are always realized by vectors. Drawing on a re-reading of Rudolf Arnheim’s account of vectors, these issues are outlined......This article revisits the concept of vectors, which, in Kress and van Leeuwen’s Reading Images (2006), plays a crucial role in distinguishing between ‘narrative’, action-oriented processes and ‘conceptual’, state-oriented processes. The use of this concept in image analysis has usually focused...

  12. Impact of Short Interval SMS Digital Data on Wind Vector Determination for a Severe Local Storms Area

    Science.gov (United States)

    Peslen, C. A.

    1979-01-01

    The impact of 5 minute interval SMS-2 visible digital image data in analyzing severe local storms is examined using wind vectors derived from cloud tracking on time lapsed sequence of geosynchronous satellite images. The cloud tracking areas are located in the Central Plains, where on 6 May 1975, hail-producing thunderstorms occurred ahead of a well defined dry line. The results demonstrate that satellite-derived wind vectors and their associated divergence fields complement conventional meteorological analyses in describing the conditions preceding severe local storm development.

  13. Short term prediction of the horizontal wind vector within a wake vortex warning system

    Energy Technology Data Exchange (ETDEWEB)

    Frech, M.; Holzaepfel, F.; Gerz, T. [DLR Deutsches Zentrum fuer Luft- und Raumfahrt e.V., Wessling (Germany). Inst. fuer Physik der Atmosphaere; Konopka, J. [Deutsche Flugsicherung (DFS) GmbH, Langen (Germany)

    2000-07-14

    A wake vortex warning system (WVWS) has been developed for Frankfurt airport. This airport has two parallel runways which are separated by 518 m, a distance too short to operate them independently because wake vortices may be advected to the adjacent runway. The objective of the WVWS is to enable operation with reduced separation between two aircraft approaching the parallel runways at appropriate wind conditions. The WVWS applies a statistical persistence model to predict the crosswind within a 20 minute period. One of the main problems identified in the old WVWS are discontinuities between successive forecasts. These forecast breakdowns were not acceptable to airtraffic controllers. At least part of the problem was related to the fact that the forecast was solely based on the prediction of crosswind. A new method is developed on the basis of 523 days of sonic anemometer measurements at Frankfurt airport. It is demonstrated that the prediction of the horizontal wind vector avoids these difficulties and significantly improves the system's performance. (orig.)

  14. Retrieving current and wind vectors from ATI SAR data: airborne evidence and inversion strategy

    Science.gov (United States)

    Martin, Adrien; Gommenginger, Christine; Chapron, Bertrand; Marquez, José; Doody, Sam

    2017-04-01

    Conventional and along-track interferometric (ATI) Synthetic Aperture Radar (SAR) sense the motion of the ocean surface by measuring the Doppler shift of reflected signals. Together with the water displacement associated with ocean currents, the SAR measurements are also affected by a Wind-wave induced Artefact Surface Velocity (WASV) caused by the velocity of Bragg scatterers and the orbital velocity of ocean surface gravity waves. The WASV has been modelled theoretically in past studies but has been estimated empirically only once using Envisat ASAR. Here we propose, firstly, to evaluate this WASV from airborne ATI SAR data, secondly, to validate the airborne retrieved surface current after correction of the WASV against HF radar measurements and thirdly to examine the best inversion strategy for a an Ocean Surface Current (OSC) satellite mission to retrieve accurately both the ocean surface current vector (OSCV) and the wind vector in the frame of an OSC satellite mission. The airborne ATI SAR data were acquired in the tidally dominated Irish Sea using a Wavemill-type dual-beam SAR interferometer. A comprehensive collection of airborne Wavemill data acquired in a star pattern over a well-instrumented site made it possible to estimate the magnitude and dependence on azimuth and incidence angle of the WASV. The airborne results compare favourably with those reported for Envisat ASAR, empirical model, which has been used to correct for it. Validation of the current retrieval capabilities of the proof-of-concept has been conducted against HF radar giving a precisions typically better than 0.1 m/s for surface current speed and 7° for direction. Comparisons with POLCOMS (1.8 km) indicate that the model reproduces well the overall temporal evolution but does not capture the high spatial variability of ocean surface currents at the maximum ebb flow. Airborne retrieved currents highlight a short-scale spatial variability up to 100m related to bathymetry channels, which

  15. Contribution of public places in proliferation of dengue vectors in Penang Island, Malaysia

    Directory of Open Access Journals (Sweden)

    Alhaji Hamisu Maimusa

    2017-03-01

    Conclusions: It was concluded that public places are good sources of potential container habitats of Aedes mosquitoes in Penang Island, Malaysia and Ae. albopictus has exclusively replaced the home-grown Ae. aegypti even in urban areas. Therefore, treatment of artificial containers in such locations is critical in Aedes mosquito control campaigns during dengue outbreaks.

  16. Comparison of the ocean surface vector winds over the Nordic Seas and their application for ocean modeling

    Science.gov (United States)

    Dukhovskoy, Dmitry; Bourassa, Mark

    2017-04-01

    Ocean processes in the Nordic Seas and northern North Atlantic are strongly controlled by air-sea heat and momentum fluxes. The predominantly cyclonic, large-scale atmospheric circulation brings the deep ocean layer up to the surface preconditioning the convective sites in the Nordic Seas for deep convection. In winter, intensive cooling and possibly salt flux from newly formed sea ice erodes the near-surface stratification and the mixed layer merges with the deeper domed layer, exposing the very weakly stratified deep water mass to direct interaction with the atmosphere. Surface wind is one of the atmospheric parameters required for estimating momentum and turbulent heat fluxes to the sea ice and ocean surface. In the ocean models forced by atmospheric analysis, errors in surface wind fields result in errors in air-sea heat and momentum fluxes, water mass formation, ocean circulation, as well as volume and heat transport in the straits. The goal of the study is to assess discrepancies across the wind vector fields from reanalysis data sets and scatterometer-derived gridded products over the Nordic Seas and northern North Atlantic and to demonstrate possible implications of these differences for ocean modeling. The analyzed data sets include the reanalysis data from the National Center for Environmental Prediction Reanalysis 2 (NCEPR2), Climate Forecast System Reanalysis (CFSR), Arctic System Reanalysis (ASR) and satellite wind products Cross-Calibrated Multi-Platform (CCMP) wind product version 1.1 and recently released version 2.0, and Remote Sensing Systems QuikSCAT data. Large-scale and mesoscale characteristics of winds are compared at interannual, seasonal, and synoptic timescales. Numerical sensitivity experiments are conducted with a coupled ice-ocean model forced by different wind fields. The sensitivity experiments demonstrate differences in the net surface heat fluxes during storm events. Next, it is hypothesized that discrepancies in the wind vorticity

  17. Magnetosheath for almost-aligned solar wind magnetic field and flow vectors: Wind observations across the dawnside magnetosheath at X = -12 Re

    Science.gov (United States)

    Farrugia, C. J.; Erkaev, N. V.; Torbert, R. B.; Biernat, H. K.; Gratton, F. T.; Szabo, A.; Kucharek, H.; Matsui, H.; Lin, R. P.; Ogilvie, K. W.; Lepping, R. P.; Smith, C. W.

    2010-08-01

    While there are many approximations describing the flow of the solar wind past the magnetosphere in the magnetosheath, the case of perfectly aligned (parallel or anti-parallel) interplanetary magnetic field (IMF) and solar wind flow vectors can be treated exactly in a magnetohydrodynamic (MHD) approach. In this work we examine a case of nearly-opposed (to within 15°) interplanetary field and flow vectors, which occurred on October 24-25, 2001 during passage of the last interplanetary coronal mass ejection in an ejecta merger. Interplanetary data are from the ACE spacecraft. Simultaneously Wind was crossing the near-Earth (X ˜ -13 Re) geomagnetic tail and subsequently made an approximately 5-hour-long magnetosheath crossing close to the ecliptic plane (Z = -0.7 Re). Geomagnetic activity was returning steadily to quiet, “ground” conditions. We first compare the predictions of the Spreiter and Rizzi theory with the Wind magnetosheath observations and find fair agreement, in particular as regards the proportionality of the magnetic field strength and the product of the plasma density and bulk speed. We then carry out a small-perturbation analysis of the Spreiter and Rizzi solution to account for the small IMF components perpendicular to the flow vector. The resulting expression is compared to the time series of the observations and satisfactory agreement is obtained. We also present and discuss observations in the dawnside boundary layer of pulsed, high-speed (v ˜ 600 km/s) flows exceeding the solar wind flow speeds. We examine various generating mechanisms and suggest that the most likely cause is a wave of frequency 3.2 mHz excited at the inner edge of the boundary layer by the Kelvin-Helmholtz instability.

  18. Noise model based ν-support vector regression with its application to short-term wind speed forecasting.

    Science.gov (United States)

    Hu, Qinghua; Zhang, Shiguang; Xie, Zongxia; Mi, Jusheng; Wan, Jie

    2014-09-01

    Support vector regression (SVR) techniques are aimed at discovering a linear or nonlinear structure hidden in sample data. Most existing regression techniques take the assumption that the error distribution is Gaussian. However, it was observed that the noise in some real-world applications, such as wind power forecasting and direction of the arrival estimation problem, does not satisfy Gaussian distribution, but a beta distribution, Laplacian distribution, or other models. In these cases the current regression techniques are not optimal. According to the Bayesian approach, we derive a general loss function and develop a technique of the uniform model of ν-support vector regression for the general noise model (N-SVR). The Augmented Lagrange Multiplier method is introduced to solve N-SVR. Numerical experiments on artificial data sets, UCI data and short-term wind speed prediction are conducted. The results show the effectiveness of the proposed technique. Copyright © 2014 Elsevier Ltd. All rights reserved.

  19. Wind turbine generator application places unique demands on tower design and materials

    Science.gov (United States)

    Kita, J. P.

    1978-01-01

    The most relevant contractual tower design requirements and goal for the Mod-1 tower are related to steel truss tower construction, cost-effective state-of-the-art design, a design life of 30 years, and maximum wind conditions of 120 mph at 30 feet elevation. The Mod-1 tower design approach was an iterative process. Static design loads were calculated and member sizes and overall geometry chosen with the use of finite element computer techniques. Initial tower dynamic characteristics were then combined with the dynamic properties of the other wind turbine components, and a series of complex dynamic computer programs were run to establish a dynamic load set and then a second tower design.

  20. Impact of Innovation and Places on Corporate Governance the Case of Wind Turbine Production

    DEFF Research Database (Denmark)

    Gunnarsson, Jan Sture Gunnar; Cikusa, Nikola Stefan; Hansen, Anca Daniela

    2017-01-01

    We examine how corporate governance changes over the industrial life cycle when places commit firms to certain governance structures. Focus is on industries where a significant part of the economic value is created by technological knowledge changing the conditions for corporate financing...

  1. Computerized system for building 'the rose' of the winds and defining the velocity and the average density of the wind power for a given place

    International Nuclear Information System (INIS)

    Valkov, I.; Dekova, I.; Arnaudov, A.; Kostadinov, A.

    2002-01-01

    This paper considers the structure and the working principle of a computerized system for building 'the rose' of the winds. The behaviour of the system has been experimentally investigated and on the basis of the received data 'the rose' of the winds has been built, a diagram of the average wind velocity at a predefined step in the course of time has been made, and the average density of the wind power has been quantitatively defined. The proposed system enables possibilities for creating a data base of wind parameters, their processing and graphical visualizing of the received results. The system allows to improve the work of devices of wild's wind gauge type. (authors)

  2. Comparison of the ocean surface vector winds from atmospheric reanalysis and scatterometer-based wind products over the Nordic Seas and the northern North Atlantic and their application for ocean modeling

    Science.gov (United States)

    Dukhovskoy, Dmitry S.; Bourassa, Mark A.; Petersen, Gudrún Nína; Steffen, John

    2017-03-01

    Ocean surface vector wind fields from reanalysis data sets and scatterometer-derived gridded products are analyzed over the Nordic Seas and the northern North Atlantic for the time period from 2000 to 2009. The data sets include the National Center for Environmental Prediction Reanalysis 2 (NCEPR2), Climate Forecast System Reanalysis (CFSR), Arctic System Reanalysis (ASR), Cross-Calibrated Multiplatform (CCMP) wind product version 1.1 and recently released version 2.0, and QuikSCAT. The goal of the study is to assess discrepancies across the wind vector fields in the data sets and demonstrate possible implications of these differences for ocean modeling. Large-scale and mesoscale characteristics of winds are compared at interannual, seasonal, and synoptic timescales. A cyclone tracking methodology is developed and applied to the wind fields to compare cyclone characteristics in the data sets. Additionally, the winds are evaluated against observations collected from meteorological buoys deployed in the Iceland and Irminger Seas. The agreement among the wind fields is better for longer time and larger spatial scales. The discrepancies are clearly apparent for synoptic timescales and mesoscales. CCMP, ASR, and CFSR show the closest overall agreement with each other. Substantial biases are found in the NCEPR2 winds. Numerical sensitivity experiments are conducted with a coupled ice-ocean model forced by different wind fields. The experiments demonstrate differences in the net surface heat fluxes during storms. In the experiment forced by NCEPR2 winds, there are discrepancies in the large-scale wind-driven ocean dynamics compared to the other experiments.

  3. Random function representation of stationary stochastic vector processes for probability density evolution analysis of wind-induced structures

    Science.gov (United States)

    Liu, Zhangjun; Liu, Zenghui

    2018-06-01

    This paper develops a hybrid approach of spectral representation and random function for simulating stationary stochastic vector processes. In the proposed approach, the high-dimensional random variables, included in the original spectral representation (OSR) formula, could be effectively reduced to only two elementary random variables by introducing the random functions that serve as random constraints. Based on this, a satisfactory simulation accuracy can be guaranteed by selecting a small representative point set of the elementary random variables. The probability information of the stochastic excitations can be fully emerged through just several hundred of sample functions generated by the proposed approach. Therefore, combined with the probability density evolution method (PDEM), it could be able to implement dynamic response analysis and reliability assessment of engineering structures. For illustrative purposes, a stochastic turbulence wind velocity field acting on a frame-shear-wall structure is simulated by constructing three types of random functions to demonstrate the accuracy and efficiency of the proposed approach. Careful and in-depth studies concerning the probability density evolution analysis of the wind-induced structure have been conducted so as to better illustrate the application prospects of the proposed approach. Numerical examples also show that the proposed approach possesses a good robustness.

  4. Evaluation of HY-2A Scatterometer Wind Vectors Using Data from Buoys, ERA-Interim and ASCAT during 2012–2014

    Directory of Open Access Journals (Sweden)

    Jianyong Xing

    2016-05-01

    Full Text Available The first Chinese operational Ku-band scatterometer on board Haiyang-2A (HY-2A, launched in August 2011, is designed for monitoring the global ocean surface wind. This study estimates the quality of the near-real-time (NRT retrieval wind speed and wind direction from the HY-2A scatterometer for 36 months from 2012 to 2014. We employed three types of sea-surface wind data from oceanic moored buoys operated by the National Data Buoy Center (NDBC and the Tropical Atmospheric Ocean project (TAO, the European Centre for Medium Range Weather Forecasting (ECMWF reanalysis data (ERA-Interim, and the advanced scatterometer (ASCAT to calculate the error statistics including mean bias, root mean square error (RMSE, and standard deviation. In addition, the rain effects on the retrieval winds were investigated using collocated Climate Prediction Center morphing method (CMORPH precipitation data. All data were collocated with the HY-2A scatterometer wind data for comparison. The quality performances of the HY-2A NRT wind vectors data (especially the wind speeds were satisfactory throughout the service period. The RMSEs of the HY-2A wind speeds relative to the NDBC, TAO, ERA-Interim, and ASCAT data were 1.94, 1.73, 2.25, and 1.62 m·s−1, respectively. The corresponding RMSEs of the wind direction were 46.63°, 43.11°, 39.93°, and 47.47°, respectively. The HY-2A scatterometer overestimated low wind speeds, especially under rainy conditions. Rain exerted a diminishing effect on the wind speed retrievals with increasing wind speed, but its effect on wind direction was robust at low and moderate wind speeds. Relative to the TAO buoy data, the RMSEs without rain effect were reduced to 1.2 m·s−1 and 39.68° for the wind speed direction, respectively, regardless of wind speed. By investigating the objective laws between rain and the retrieval winds from HY-2A, we could improve the quality of wind retrievals through future studies.

  5. On the flow of an electrically conducting gas past a slender body of revolution placed in a circular wind tunnel in the presence of a crossed magnetic field

    International Nuclear Information System (INIS)

    Suwa, Shigeaki; Kusukawa, Ken-ichi.

    1976-01-01

    The wind tunnel interference problem in magnetohydrodynamics, in which an inviscid compressible fluid with small electrical conductivity flows steadily past a slender axi-symmetric pointed body of revolution placed in a cylindrical perfectly insulated wind tunnel, in the presence of a crossed magnetic field, is considered. Using the analytical method which was studied by one of the present authors, the streamlines and the space charge in a cross section are calculated. (auth.)

  6. Back-to-back three-level converter controlled by a novel space-vector hysteresis current control for wind conversion systems

    Energy Technology Data Exchange (ETDEWEB)

    Ghennam, Tarak [Laboratoire d' Electronique de Puissance (LEP), UER: Electrotechnique, Ecole Militaire Polytechnique d' Alger, BP 17, Bordj EL Bahri, Alger (Algeria); Berkouk, El-Madjid [Laboratoire de Commande des Processus (LCP), Ecole Nationale Polytechnique d' Alger, BP 182, 10 avenue Hassen Badi, 16200 el Harrach (Algeria)

    2010-04-15

    In this paper, a novel space-vector hysteresis current control (SVHCC) is proposed for a back-to-back three-level converter which is used as an electronic interface in a wind conversion system. The proposed SVHCC controls the active and reactive powers delivered to the grid by the doubly fed induction machine (DFIM) through the control of its rotor currents. In addition, it controls the neutral point voltage by using the redundant inverter switching states. The three rotor current errors are gathered into a single space-vector quantity. The magnitude of the error vector is limited within boundary areas of a square shape. The control scheme is based firstly on the detection of the area and sector in which the vector tip of the current error can be located. Then, an appropriate voltage vector among the 27 voltage vectors of the three-level voltage source inverter (VSI) is applied to push the error vector towards the hysteresis boundaries. Simple look-up tables are required for the area and sector detection, and also for vector selection. The performance of the proposed control technique has been verified by simulations. (author)

  7. A Breath of Fresh Air in Foraging Theory: The Importance of Wind for Food Size Selection in a Central-Place Forager.

    Science.gov (United States)

    Alma, Andrea Marina; Farji-Brener, Alejandro G; Elizalde, Luciana

    2017-09-01

    Empirical data about food size carried by central-place foragers do not often fit with the optimum predicted by classical foraging theory. Traditionally, biotic constraints such as predation risk and competition have been proposed to explain this inconsistency, leaving aside the possible role of abiotic factors. Here we documented how wind affects the load size of a central-place forager (leaf-cutting ants) through a mathematical model including the whole foraging process. The model showed that as wind speed at ground level increased from 0 to 2 km/h, load size decreased from 91 to 30 mm 2 , a prediction that agreed with empirical data from windy zones, highlighting the relevance of considering abiotic factors to predict foraging behavior. Furthermore, wind reduced the range of load sizes that workers should select to maintain a similar rate of food intake and decreased the foraging rate by ∼70% when wind speed increased 1 km/h. These results suggest that wind could reduce the fitness of colonies and limit the geographic distribution of leaf-cutting ants. The developed model offers a complementary explanation for why load size in central-place foragers may not fit theoretical predictions and could serve as a basis to study the effects of other abiotic factors that influence foraging.

  8. The importance of on-site evaluation for placing renewable energy in the landscape: A case study of the Búrfell wind farm (Iceland

    Directory of Open Access Journals (Sweden)

    Frantál Bohumil

    2017-12-01

    Full Text Available Using a case study of the Búrfell wind farm project, a large wind farm proposed in the Central Highlands of Iceland, the authors attempt to provide new insights into the factors shaping subjective landscape perceptions and attitudes to renewable energy developments, and into alternative methods that may be used for their assessment. The research was based on an on-site visit and actual experience of the place, investigated using a combination of mental mapping, the technique of the semantic differential and a questionnaire survey. The results show that participants visiting a landscape and using all sensory organs in combination with mental mapping, can reveal more important information than using only ‘laboratory’ methods with static photographs. The results suggest that the perception of landscape is highly subjective. Those perceiving the landscape as more open, homogenous, industrial, unfamiliar and resilient also consider it more compatible with wind turbines. The perception of the landscape’s compatibility with wind turbines proved to be a dominant factor shaping attitudes towards the project. The acceptance of wind turbines is not, however, inconsistent with the perception of landscape as beautiful, wild and unique. Participants from more densely populated countries and countries with a developed wind energy industry were more tolerant of wind turbines in the Icelandic landscape.

  9. Maximum power extraction under different vector-control schemes and grid-synchronization strategy of a wind-driven Brushless Doubly-Fed Reluctance Generator.

    Science.gov (United States)

    Mousa, Mohamed G; Allam, S M; Rashad, Essam M

    2018-01-01

    This paper proposes an advanced strategy to synchronize the wind-driven Brushless Doubly-Fed Reluctance Generator (BDFRG) to the grid-side terminals. The proposed strategy depends mainly upon determining the electrical angle of the grid voltage, θ v and using the same transformation matrix of both the power winding and grid sides to ensure that the generated power-winding voltage has the same phase-sequence of the grid-side voltage. On the other hand, the paper proposes a vector-control (power-winding flux orientation) technique for maximum wind-power extraction under two schemes summarized as; unity power-factor operation and minimum converter-current. Moreover, a soft-starting method is suggested to avoid the employed converter over-current. The first control scheme is achieved by adjusting the command power-winding reactive power at zero for a unity power-factor operation. However, the second scheme depends on setting the command d-axis control-winding current at zero to maximize the ratio of the generator electromagnetic-torque per the converter current. This enables the system to get a certain command torque under minimum converter current. A sample of the obtained simulation and experimental results is presented to check the effectiveness of the proposed control strategies. Copyright © 2017 ISA. Published by Elsevier Ltd. All rights reserved.

  10. The Energy Commission's notice to the Minister of Natural Resources regarding the place of wind energy in Quebec's energy portfolio

    International Nuclear Information System (INIS)

    Dumais, A.; Frayne, A.; Tanguay, F.

    1998-01-01

    In December 1997 Quebec's Minister of Natural Resources requested that the Energy Commission advise him on the quota given to wind energy in the future energy development plans of Hydro-Quebec. The Commission's report to the Minister includes 18 recommendations. Among these is a recommendation that an assessment of wind resources be conducted as soon as possible to identify suitable sites for the installation of wind turbines. A provincial program for the development of wind energy is also recommended, to be initiated by the year 2002, and that it should proceed over the next nine years to reach a target production capacity of 450 MW by the year 2011. This production would come from the yearly installation of 60 to 70 wind turbines of 750 kV. The Commission also recommended that in the initial years costs for this wind energy not exceed that of the Le Nordais project, i.e. 5.8 cents per kWh. Any additional costs incurred in the generation of wind electricity over conventional hydro power should be assumed by the Quebec Government. Conversely, in instances where the wind power is sold to consumers outside of the province, Hydro-Quebec should pay for the full cost of this power. 8 tabs., 1 appendix

  11. Short-Term Wind Speed Forecasting Using the Data Processing Approach and the Support Vector Machine Model Optimized by the Improved Cuckoo Search Parameter Estimation Algorithm

    Directory of Open Access Journals (Sweden)

    Chen Wang

    2016-01-01

    Full Text Available Power systems could be at risk when the power-grid collapse accident occurs. As a clean and renewable resource, wind energy plays an increasingly vital role in reducing air pollution and wind power generation becomes an important way to produce electrical power. Therefore, accurate wind power and wind speed forecasting are in need. In this research, a novel short-term wind speed forecasting portfolio has been proposed using the following three procedures: (I data preprocessing: apart from the regular normalization preprocessing, the data are preprocessed through empirical model decomposition (EMD, which reduces the effect of noise on the wind speed data; (II artificially intelligent parameter optimization introduction: the unknown parameters in the support vector machine (SVM model are optimized by the cuckoo search (CS algorithm; (III parameter optimization approach modification: an improved parameter optimization approach, called the SDCS model, based on the CS algorithm and the steepest descent (SD method is proposed. The comparison results show that the simple and effective portfolio EMD-SDCS-SVM produces promising predictions and has better performance than the individual forecasting components, with very small root mean squared errors and mean absolute percentage errors.

  12. Comparison of several measure-correlate-predict models using support vector regression techniques to estimate wind power densities. A case study

    International Nuclear Information System (INIS)

    Díaz, Santiago; Carta, José A.; Matías, José M.

    2017-01-01

    Highlights: • Eight measure-correlate-predict (MCP) models used to estimate the wind power densities (WPDs) at a target site are compared. • Support vector regressions are used as the main prediction techniques in the proposed MCPs. • The most precise MCP uses two sub-models which predict wind speed and air density in an unlinked manner. • The most precise model allows to construct a bivariable (wind speed and air density) WPD probability density function. • MCP models trained to minimise wind speed prediction error do not minimise WPD prediction error. - Abstract: The long-term annual mean wind power density (WPD) is an important indicator of wind as a power source which is usually included in regional wind resource maps as useful prior information to identify potentially attractive sites for the installation of wind projects. In this paper, a comparison is made of eight proposed Measure-Correlate-Predict (MCP) models to estimate the WPDs at a target site. Seven of these models use the Support Vector Regression (SVR) and the eighth the Multiple Linear Regression (MLR) technique, which serves as a basis to compare the performance of the other models. In addition, a wrapper technique with 10-fold cross-validation has been used to select the optimal set of input features for the SVR and MLR models. Some of the eight models were trained to directly estimate the mean hourly WPDs at a target site. Others, however, were firstly trained to estimate the parameters on which the WPD depends (i.e. wind speed and air density) and then, using these parameters, the target site mean hourly WPDs. The explanatory features considered are different combinations of the mean hourly wind speeds, wind directions and air densities recorded in 2014 at ten weather stations in the Canary Archipelago (Spain). The conclusions that can be drawn from the study undertaken include the argument that the most accurate method for the long-term estimation of WPDs requires the execution of a

  13. Comparison Between Wind Power Prediction Models Based on Wavelet Decomposition with Least-Squares Support Vector Machine (LS-SVM and Artificial Neural Network (ANN

    Directory of Open Access Journals (Sweden)

    Maria Grazia De Giorgi

    2014-08-01

    Full Text Available A high penetration of wind energy into the electricity market requires a parallel development of efficient wind power forecasting models. Different hybrid forecasting methods were applied to wind power prediction, using historical data and numerical weather predictions (NWP. A comparative study was carried out for the prediction of the power production of a wind farm located in complex terrain. The performances of Least-Squares Support Vector Machine (LS-SVM with Wavelet Decomposition (WD were evaluated at different time horizons and compared to hybrid Artificial Neural Network (ANN-based methods. It is acknowledged that hybrid methods based on LS-SVM with WD mostly outperform other methods. A decomposition of the commonly known root mean square error was beneficial for a better understanding of the origin of the differences between prediction and measurement and to compare the accuracy of the different models. A sensitivity analysis was also carried out in order to underline the impact that each input had in the network training process for ANN. In the case of ANN with the WD technique, the sensitivity analysis was repeated on each component obtained by the decomposition.

  14. Characterization Of Ocean Wind Vector Retrievals Using ERS-2 High-Resolution Long-Term Dataset And Buoy Measurements

    Science.gov (United States)

    Polverari, F.; Talone, M.; Crapolicchio, R. Levy, G.; Marzano, F.

    2013-12-01

    The European Remote-sensing Satellite (ERS)-2 scatterometer provides wind retrievals over Ocean. To satisfy the needs of high quality and homogeneous set of scatterometer measurements, the European Space Agency (ESA) has developed the project Advanced Scatterometer Processing System (ASPS) with which a long-term dataset of new ERS-2 wind products, with an enhanced resolution of 25km square, has been generated by the reprocessing of the entire ERS mission. This paper presents the main results of the validation work of such new dataset using in situ measurements provided by the Prediction and Research Moored Array in the Tropical Atlantic (PIRATA). The comparison indicates that, on average, the scatterometer data agree well with buoys measurements, however the scatterometer tends to overestimates lower winds and underestimates higher winds.

  15. Correlation-constrained and sparsity-controlled vector autoregressive model for spatio-temporal wind power forecasting

    DEFF Research Database (Denmark)

    Zhao, Yongning; Ye, Lin; Pinson, Pierre

    2018-01-01

    The ever-increasing number of wind farms has brought both challenges and opportunities in the development of wind power forecasting techniques to take advantage of interdependenciesbetweentensorhundredsofspatiallydistributedwind farms, e.g., over a region. In this paper, a Sparsity-Controlled Vec......The ever-increasing number of wind farms has brought both challenges and opportunities in the development of wind power forecasting techniques to take advantage of interdependenciesbetweentensorhundredsofspatiallydistributedwind farms, e.g., over a region. In this paper, a Sparsity...... matrices in direct manner. However this original SC-VAR is difficult to implement due to its complicated constraints and the lack of guidelines for setting its parameters. To reduce the complexity of this MINLP and to make it possible to incorporate prior expert knowledge to benefit model building...

  16. Assessment and Analysis of QuikSCAT Vector Wind Products for the Gulf of Mexico: A Long-Term and Hurricane Analysis

    Directory of Open Access Journals (Sweden)

    Eurico D’Sa

    2008-03-01

    Full Text Available The northern Gulf of Mexico is a region that has been frequently impacted in recent years by natural disasters such as hurricanes. The use of remote sensing data such as winds from NASA’s QuikSCAT satellite sensor would be useful for emergency preparedness during such events. In this study, the performance of QuikSCAT products, including JPL’s latest Level 2B (L2B 12.5 km swath winds, were evaluated with respect to buoy-measured winds in the Gulf of Mexico for the period January 2005 to February 2007. Regression analyses indicated better accuracy of QuikSCAT’s L2B DIRTH, 12.5 km than the Level 3 (L3, 25 km wind product. QuikSCAT wind data were compared directly with buoy data keeping a maximum time interval of 20 min and spatial interval of 0.1° (≈10 km. R2 values for moderate wind speeds were 0.88 and 0.93 for L2B, and 0.75 and 0.89 for L3 for speed and direction, respectively. QuikSCAT wind comparisons for buoys located offshore were better than those located near the coast. Hurricanes that took place during 2002-06 were studied individually to obtain regressions of QuikSCAT versus buoys for those events. Results show QuikSCAT’s L2B DIRTH wind product compared well with buoys during hurricanes up to the limit of buoy measurements. Comparisons with the National Hurricane Center (NHC best track analyses indicated QuikSCAT winds to be lower than those obtained by NHC, possibly due to rain contamination, while buoy measurements appeared to be constrained at high wind speeds. This study has confirmed good agreement of the new QuikSCAT L2B product with buoy measurements and further suggests its potential use during extreme weather conditions in the Gulf of Mexico.

  17. Better Place

    DEFF Research Database (Denmark)

    Rask, Morten; Bakke, Nikolas; Lindhøj, Jan

    Better Place is trying to reshape the automotive industry by shifting transportation from a dependency on oil to a reliance on environmentally friendly renewable energy. Better Place is developing an extensive infrastructure system that will utilise overcapacity in the production of wind power...... among others and that will drive the global transportation industry to becoming driven by electric vehicles (EVs). Better Place does this by selling its customers 'mileage' and a car without a battery. The case highlights the internationalisation process of Better Place from an international business...... perspective in order to encourage a discussion and debate about how Better Place can make their grand vision a reality in the future by overcoming the obstacles that historically have been challenging the rise of the EV industry. The case includes a historical background of the EV industry by using Denmark...

  18. Striatal modulation of BDNF expression using microRNA124a-expressing lentiviral vectors impairs ethanol-induced conditioned-place preference and voluntary alcohol consumption.

    Science.gov (United States)

    Bahi, Amine; Dreyer, Jean-Luc

    2013-07-01

    Alcohol abuse is a major health, economic and social concern in modern societies, but the exact molecular mechanisms underlying ethanol addiction remain elusive. Recent findings show that small non-coding microRNA (miRNA) signaling contributes to complex behavioral disorders including drug addiction. However, the role of miRNAs in ethanol-induced conditioned-place preference (CPP) and voluntary alcohol consumption has not yet been directly addressed. Here, we assessed the expression profile of miR124a in the dorsal striatum of rats upon ethanol intake. The results show that miR124a was downregulated in the dorso-lateral striatum (DLS) following alcohol drinking. Then, we identified brain-derived neurotrophic factor (BDNF) as a direct target of miR124a. In fact, BDNF mRNA was upregulated following ethanol drinking. We used lentiviral vector (LV) gene transfer technology to further address the role of miR124a and its direct target BDNF in ethanol-induced CPP and alcohol consumption. Results reveal that stereotaxic injection of LV-miR124a in the DLS enhances ethanol-induced CPP as well as voluntary alcohol consumption in a two-bottle choice drinking paradigm. Moreover, miR124a-silencer (LV-siR124a) as well as LV-BDNF infusion in the DLS attenuates ethanol-induced CPP as well as voluntary alcohol consumption. Importantly, LV-miR124a, LV-siR124a and LV-BDNF have no effect on saccharin and quinine intake. Our findings indicate that striatal miR124a and BDNF signaling have crucial roles in alcohol consumption and ethanol conditioned reward. © 2013 Federation of European Neuroscience Societies and John Wiley & Sons Ltd.

  19. Combining dispersion modelling with synoptic patterns to understand the wind-borne transport into the UK of the bluetongue disease vector.

    Science.gov (United States)

    Burgin, Laura; Ekström, Marie; Dessai, Suraje

    2017-07-01

    Bluetongue, an economically important animal disease, can be spread over long distances by carriage of insect vectors (Culicoides biting midges) on the wind. The weather conditions which influence the midge's flight are controlled by synoptic scale atmospheric circulations. A method is proposed that links wind-borne dispersion of the insects to synoptic circulation through the use of a dispersion model in combination with principal component analysis (PCA) and cluster analysis. We illustrate how to identify the main synoptic situations present during times of midge incursions into the UK from the European continent. A PCA was conducted on high-pass-filtered mean sea-level pressure data for a domain centred over north-west Europe from 2005 to 2007. A clustering algorithm applied to the PCA scores indicated the data should be divided into five classes for which averages were calculated, providing a classification of the main synoptic types present. Midge incursion events were found to mainly occur in two synoptic categories; 64.8% were associated with a pattern displaying a pressure gradient over the North Atlantic leading to moderate south-westerly flow over the UK and 17.9% of the events occurred when high pressure dominated the region leading to south-easterly or easterly winds. The winds indicated by the pressure maps generally compared well against observations from a surface station and analysis charts. This technique could be used to assess frequency and timings of incursions of virus into new areas on seasonal and decadal timescales, currently not possible with other dispersion or biological modelling methods.

  20. Final Results from Mexnext-I. Analysis of detailed aerodynamic measurements on a 4.5 m diameter rotor placed in the large German Dutch Wind Tunnel DNW

    Energy Technology Data Exchange (ETDEWEB)

    Schepers, J.G.; Boorsma, K. [Energy research Center of the Netherlands ECN, Petten (Netherlands); Munduate, X. [National Renewable Energy Center, CENER, Pamplona (Spain)

    2013-02-15

    The paper presents the final results from the first phase of IEA Task 29 'Mexnext'. Mexnext was a joint project in which 20 parties from 11 different countries cooperated. The main aim of Mexnext was to analyse the wind tunnel measurements which have been taken in the EU project 'MEXICO'. In the MEXICO project 10 institutes from 6 countries cooperated in doing experiments on an instrumented, three-bladed wind turbine of 4.5 m diameter placed in the 9.5 by 9.5 m{sup 2} open section of the Large Low-speed Facility (LLF) of the test facility DNW (German-Dutch Wind Tunnels). Pressure distributions on the blades were obtained from 148 Kulite pressure sensors, distributed over 5 sections at 25, 35, 60, 82 and 92% radial position respectively. Blade loads were monitored through two strain-gauge bridges at each blade root. Most interesting however are the extensive PIV flow field measurements, which have been taken simultaneously with the pressure and load measurements. As a result of the international collaboration within this task a very thorough analysis of the data could be carried out and a large number of codes were validated not only in terms of loads but also in terms of underlying flow field. The paper will present several results from Mexnext-I, i.e. validation results and conclusion on modelling deficiencies and directions for model improvement. The future plans of the Mexnext consortium are also briefly discussed. Amongst these are Mexnext-II, a project in which also aerodynamic measurements other than MEXICO are included, and 'New MEXICO' in which additional measurement on the MEXICO model are performed.

  1. Directional Bias of TAO Daily Buoy Wind Vectors in the Central Equatorial Pacific Ocean from November 2008 to January 2010

    Directory of Open Access Journals (Sweden)

    Ge Peng

    2014-07-01

    Full Text Available This article documents a systematic bias in surface wind directions between the TAO buoy measurements at 0°, 170°W and the ECMWF analysis and forecasts. This bias was of the order 10° and persisted from November 2008 to January 2010, which was consistent with a post-recovery calibration drift in the anemometer vane. Unfortunately, the calibration drift was too time-variant to be used to correct the data so the quality flag for this deployment was adjusted to reflect low data quality. The primary purpose of this paper is to inform users in the modelling and remote-sensing community about this systematic, persistent wind directional bias, which will allow users to make an educated decision on using the data and be aware of its potential impact to their downstream product quality. The uncovering of this bias and its source demonstrates the importance of continuous scientific oversight and effective user-data provider communication in stewarding scientific data. It also suggests the need for improvement in the ability of buoy data quality control procedures of the TAO and ECMWF systems to detect future wind directional systematic biases such as the one described here.

  2. Final Results from Mexnext-I: Analysis of detailed aerodynamic measurements on a 4.5 m diameter rotor placed in the large German Dutch Wind Tunnel DNW

    International Nuclear Information System (INIS)

    Schepers, J G; Boorsma, K; Munduate, X

    2014-01-01

    The paper presents the final results from the first phase of IEA Task 29 'Mexnext'. Mexnext was a joint project in which 20 parties from 11 different countries cooperated. The main aim of Mexnext was to analyse the wind tunnel measurements which have been taken in the EU project 'MEXICO'. In the MEXICO project 10 institutes from 6 countries cooperated in doing experiments on an instrumented, 3 bladed wind turbine of 4.5 m diameter placed in the 9.5 by 9.5 m 2 open section of the Large Low-speed Facility (LLF) of DNW in the Netherlands. Pressure distributions on the blades were obtained from 148 Kulite pressure sensors, distributed over 5 sections at 25, 35, 60, 82 and 92 % radial position respectively. Blade loads were monitored through two strain-gauge bridges at each blade root. Most interesting however are the extensive PIV flow field measurements, which have been taken simultaneously with the pressure and load measurements. As a result of the international collaboration within this task a very thorough analysis of the data could be carried out and a large number of codes were validated not only in terms of loads but also in terms of underlying flow field. The paper will present several results from Mexnext-I, i.e. validation results and conclusion on modelling deficiencies and directions for model improvement. The future plans of the Mexnext consortium are also briefly discussed. Amongst these are Mexnext-II, a project in which also aerodynamic measurements other than MEXICO are included, and 'New MEXICO' in which additional measurement on the MEXICO model are performed

  3. World Wind

    Data.gov (United States)

    National Aeronautics and Space Administration — World Wind allows any user to zoom from satellite altitude into any place on Earth, leveraging high resolution LandSat imagery and SRTM elevation data to experience...

  4. Designated Places

    Data.gov (United States)

    California Natural Resource Agency — Census 2000 Place Names provides a seamless statewide GIS layer of places, including census designated places (CDP), consolidated cities, and incorporated places,...

  5. Taking place, screening place

    DEFF Research Database (Denmark)

    Hansen, Kim Toft; Waade, Anne Marit

    2019-01-01

    We introduce location studies as a new empirical approach to screen studies. Location studies represent an interdisciplinary perspective, including media, aesthetics and geography, and reflect a growing interest in places in a global media and consumption culture. The chapter analyses two recent......) with one being traditional and the other being commercial; both dramas include discussions of localities and social heritage, and both use local sports as a common metaphor for social cohesion; and both series have been partly funded by a local film Danish commissioner. However, The Legacy is shot...... to a large extent in studios, while Norskov is shot entirely on location. The study is based on interviews with producers, broadcasters, location scouts, production designers and writers, as well as quantitative and qualitative textual analyses of television drama series, the geographical places, and related...

  6. The importance of on-site evaluation for placing renewable energy in the landscape: A case study of the Búrfell wind farm (Iceland)

    Czech Academy of Sciences Publication Activity Database

    Frantál, Bohumil; Bevk, T.; van Veelen, B.; Hărmănescu, M.; Benediktsson, K.

    2017-01-01

    Roč. 25, č. 4 (2017), s. 234-247 ISSN 1210-8812 R&D Projects: GA ČR GA16-04483S Institutional support: RVO:68145535 Keywords : wind energy * landscape perception * Iceland Subject RIV: DE - Earth Magnetism, Geodesy, Geography OBOR OECD: Environmental sciences (social aspects) Impact factor: 2.149, year: 2016 http://www.geonika.cz/EN/research/ENMGRClanky/2017_4_FRANT%C3%81L.pdf

  7. Spoiled darkness? Sense of place and annoyance over obstruction lights from the world’s largest wind turbine test centre in Denmark

    DEFF Research Database (Denmark)

    Rudolph, David Philipp; Kirkegaard, Julia Kirch; Lyhne, Ivar

    2017-01-01

    strategies. In particular, the discussion focuses on the perceived annoyance in relation to the perceived changes in sense of place, hereunder the loss of the area’s unique night darkness. We argue that perceived annoyance can only be mitigated through coping strategies to a limited extent, as a) perceived...... effects on sense of place are distinctive in shaping annoyance, and b) an internalisation of planning-related inequities persists....

  8. Wind power. [electricity generation

    Science.gov (United States)

    Savino, J. M.

    1975-01-01

    A historical background on windmill use, the nature of wind, wind conversion system technology and requirements, the economics of wind power and comparisons with alternative systems, data needs, technology development needs, and an implementation plan for wind energy are presented. Considerable progress took place during the 1950's. Most of the modern windmills feature a wind turbine electricity generator located directly at the top of their rotor towers.

  9. Vector analysis

    CERN Document Server

    Newell, Homer E

    2006-01-01

    When employed with skill and understanding, vector analysis can be a practical and powerful tool. This text develops the algebra and calculus of vectors in a manner useful to physicists and engineers. Numerous exercises (with answers) not only provide practice in manipulation but also help establish students' physical and geometric intuition in regard to vectors and vector concepts.Part I, the basic portion of the text, consists of a thorough treatment of vector algebra and the vector calculus. Part II presents the illustrative matter, demonstrating applications to kinematics, mechanics, and e

  10. About vectors

    CERN Document Server

    Hoffmann, Banesh

    1975-01-01

    From his unusual beginning in ""Defining a vector"" to his final comments on ""What then is a vector?"" author Banesh Hoffmann has written a book that is provocative and unconventional. In his emphasis on the unresolved issue of defining a vector, Hoffmann mixes pure and applied mathematics without using calculus. The result is a treatment that can serve as a supplement and corrective to textbooks, as well as collateral reading in all courses that deal with vectors. Major topics include vectors and the parallelogram law; algebraic notation and basic ideas; vector algebra; scalars and scalar p

  11. Thermal and Pressure Characterization of a Wind Tunnel Force Balance Using the Single Vector System. Experimental Design and Analysis Approach to Model Pressure and Temperature Effects in Hypersonic Wind Tunnel Research

    Science.gov (United States)

    Lynn, Keith C.; Commo, Sean A.; Johnson, Thomas H.; Parker, Peter A,

    2011-01-01

    Wind tunnel research at NASA Langley Research Center s 31-inch Mach 10 hypersonic facility utilized a 5-component force balance, which provided a pressurized flow-thru capability to the test article. The goal of the research was to determine the interaction effects between the free-stream flow and the exit flow from the reaction control system on the Mars Science Laboratory aeroshell during planetary entry. In the wind tunnel, the balance was exposed to aerodynamic forces and moments, steady-state and transient thermal gradients, and various internal balance cavity pressures. Historically, these effects on force measurement accuracy have not been fully characterized due to limitations in the calibration apparatus. A statistically designed experiment was developed to adequately characterize the behavior of the balance over the expected wind tunnel operating ranges (forces/moments, temperatures, and pressures). The experimental design was based on a Taylor-series expansion in the seven factors for the mathematical models. Model inversion was required to calculate the aerodynamic forces and moments as a function of the strain-gage readings. Details regarding transducer on-board compensation techniques, experimental design development, mathematical modeling, and wind tunnel data reduction are included in this paper.

  12. Children's Places

    DEFF Research Database (Denmark)

    Using a cross-cultural approach the book investigates children's places in different societies. "Children's Places" examines the ways in which children and adults, from their different vantage-points in society, negotiate proper places of children in both social and spatial terms. It looks at some...

  13. The turning of the wind in the atmospheric boundary layer

    DEFF Research Database (Denmark)

    Pena Diaz, Alfredo; Gryning, Sven-Erik; Floors, Rogier Ralph

    2014-01-01

    Here we use accurate observations of the wind speed vector to analyze the behavior with height of the wind direction. The observations are a combination of tall meteorological mast and long-range wind lidar measurements covering the entire atmospheric boundary layer. The observations were performed...... winds underpredict the turning of the wind and the boundary-layer winds in general....

  14. Elementary vectors

    CERN Document Server

    Wolstenholme, E Œ

    1978-01-01

    Elementary Vectors, Third Edition serves as an introductory course in vector analysis and is intended to present the theoretical and application aspects of vectors. The book covers topics that rigorously explain and provide definitions, principles, equations, and methods in vector analysis. Applications of vector methods to simple kinematical and dynamical problems; central forces and orbits; and solutions to geometrical problems are discussed as well. This edition of the text also provides an appendix, intended for students, which the author hopes to bridge the gap between theory and appl

  15. Place Branding

    DEFF Research Database (Denmark)

    Medway, Dominic; Swanson, Kathryn; Neirotti, Lisa Delpy

    2015-01-01

    Purpose: – The purpose of this paper is to report on a special session entitled “Place branding: Are we wasting our time?”, held at the American Marketing Association’s Summer Marketing Educators’ conference in 2014. Design/methodology/approach: – The report details the outcome of an Oxford......: – The outcome of the debate points towards a need for place brands to develop as more inclusive and organic entities, in which case it may be best for place practitioners to avoid creating and imposing a place brand and instead help shape it from the views of stakeholder constituencies. This shifts the notion...... of place branding towards an activity centred on “curation”. Originality/value: – The use of a competitive debating format as a means for exploring academic ideas and concepts in the place management field....

  16. Thin Places

    OpenAIRE

    Lockwood, Sandra Elizabeth

    2013-01-01

    This inquiry into the three great quests of the twentieth century–the South Pole, Mount Everest, and the Moon–examines our motivations to venture into these sublime, yet life-taking places. The Thin Place was once the destination of the religious pilgrim seeking transcendence in an extreme environment. In our age, the Thin Place quest has morphed into a challenge to evolve beyond the confines of our own physiology; through human ingenuity and invention, we reach places not meant to accommod...

  17. A robust combination approach for short-term wind speed forecasting and analysis – Combination of the ARIMA (Autoregressive Integrated Moving Average), ELM (Extreme Learning Machine), SVM (Support Vector Machine) and LSSVM (Least Square SVM) forecasts using a GPR (Gaussian Process Regression) model

    International Nuclear Information System (INIS)

    Wang, Jianzhou; Hu, Jianming

    2015-01-01

    With the increasing importance of wind power as a component of power systems, the problems induced by the stochastic and intermittent nature of wind speed have compelled system operators and researchers to search for more reliable techniques to forecast wind speed. This paper proposes a combination model for probabilistic short-term wind speed forecasting. In this proposed hybrid approach, EWT (Empirical Wavelet Transform) is employed to extract meaningful information from a wind speed series by designing an appropriate wavelet filter bank. The GPR (Gaussian Process Regression) model is utilized to combine independent forecasts generated by various forecasting engines (ARIMA (Autoregressive Integrated Moving Average), ELM (Extreme Learning Machine), SVM (Support Vector Machine) and LSSVM (Least Square SVM)) in a nonlinear way rather than the commonly used linear way. The proposed approach provides more probabilistic information for wind speed predictions besides improving the forecasting accuracy for single-value predictions. The effectiveness of the proposed approach is demonstrated with wind speed data from two wind farms in China. The results indicate that the individual forecasting engines do not consistently forecast short-term wind speed for the two sites, and the proposed combination method can generate a more reliable and accurate forecast. - Highlights: • The proposed approach can make probabilistic modeling for wind speed series. • The proposed approach adapts to the time-varying characteristic of the wind speed. • The hybrid approach can extract the meaningful components from the wind speed series. • The proposed method can generate adaptive, reliable and more accurate forecasting results. • The proposed model combines four independent forecasting engines in a nonlinear way.

  18. Healthy Places

    Centers for Disease Control (CDC) Podcasts

    Every person has a stake in environmental public health. As the environment deteriorates, so does the physical and mental health of the people within it. Healthy places are those designed and built to improve the quality of life for all people who live, work, worship, learn, and play within their borders -- where every person is free to make choices amid a variety of healthy, available, accessible, and affordable options. The CDC recognizes significant health issues and places that are vital in developing the Healthy Places program and provides examples in this report.

  19. Vector analysis

    CERN Document Server

    Brand, Louis

    2006-01-01

    The use of vectors not only simplifies treatments of differential geometry, mechanics, hydrodynamics, and electrodynamics, but also makes mathematical and physical concepts more tangible and easy to grasp. This text for undergraduates was designed as a short introductory course to give students the tools of vector algebra and calculus, as well as a brief glimpse into these subjects' manifold applications. The applications are developed to the extent that the uses of the potential function, both scalar and vector, are fully illustrated. Moreover, the basic postulates of vector analysis are brou

  20. Place (National)

    Data.gov (United States)

    Department of Transportation — This map layer includes cities and towns in the United States, Puerto Rico, and the U.S. Virgin Islands (NTAD). A city or town is a place with a recorded population,...

  1. Vector velocimeter

    DEFF Research Database (Denmark)

    2012-01-01

    The present invention relates to a compact, reliable and low-cost vector velocimeter for example for determining velocities of particles suspended in a gas or fluid flow, or for determining velocity, displacement, rotation, or vibration of a solid surface, the vector velocimeter comprising a laser...

  2. Elsaesser variable analysis of fluctuations in the ion foreshock and undisturbed solar wind

    Science.gov (United States)

    Labelle, James; Treumann, Rudolf A.; Marsch, Eckart

    1994-01-01

    Magnetohydrodynamics (MHD) fluctuations in the solar wind have been investigated previously by use of Elsaesser variables. In this paper, we present a comparison of the spectra of Elsaesser variables in the undisturbed solar wind at 1 AU and in the ion foreshock in front of the Earth. Both observations take place under relatively strong solar wind flow speed conditions (approximately equal 600 km/s). In the undisturbed solar wind we find that outward propagating Alfven waves dominate, as reported by other observers. In the ion foreshock the situation is more complex, with neither outward nor inward propagation dominating over the entire range investigated (1-10 mHz). Measurements of the Poynting vectors associated with the fluctuations are consistent with the Elsaesser variable analysis. These results generally support interpretations of the Elsaesser variables which have been made based strictly on solar wind data and provide additional insight into the nature of the ion foreshock turbulence.

  3. Measurement of the sea surface wind speed and direction by an airborne microwave radar altimeter

    Energy Technology Data Exchange (ETDEWEB)

    Nekrassov, A. [GKSS-Forschungszentrum Geesthacht GmbH (Germany). Inst. fuer Hydrophysik

    2001-07-01

    A pilot needs operational information about wind over sea as well as wave height to provide safety of a hydroplane landing on water. Near-surface wind speed and direction can be obtained with an airborne microwave scatterometer, radar designed for measuring the scatter characteristics of a surface. Mostly narrow-beam antennas are applied for such wind measurement. Unfortunately, a microwave narrow-beam antenna has considerable size that hampers its placing on flying apparatus. In this connection, a possibility to apply a conventional airborne radar altimeter as a scatterometer with a nadir-looking wide-beam antenna in conjunction with Doppler filtering for recovering the wind vector over sea is discussed, and measuring algorithms of sea surface wind speed and direction are proposed. The obtained results can be used for creation of an airborne radar system for operational measurement of the sea roughness characteristics and for safe landing of a hydroplane on water. (orig.)

  4. OW CCMP Ocean Surface Wind

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — The Cross-Calibrated Multi-Platform (CCMP) Ocean Surface Wind Vector Analyses (Atlas et al., 2011) provide a consistent, gap-free long-term time-series of monthly...

  5. Healthy Places

    Centers for Disease Control (CDC) Podcasts

    2007-04-10

    Every person has a stake in environmental public health. As the environment deteriorates, so does the physical and mental health of the people within it. Healthy places are those designed and built to improve the quality of life for all people who live, work, worship, learn, and play within their borders -- where every person is free to make choices amid a variety of healthy, available, accessible, and affordable options. The CDC recognizes significant health issues and places that are vital in developing the Healthy Places program and provides examples in this report.  Created: 4/10/2007 by CDC National Center for Environmental Health.   Date Released: 4/13/2007.

  6. Designed Places

    DEFF Research Database (Denmark)

    Stender, Marie

    The 2008 financial crisis has left traces in the built environment of Copenhagen like many other places: Building projects are left unfinished or their function or finish is changed due to new economic circumstances. An ethnographic exploration of these traces exposes central aspects of what is a......, and when the ceilings leak water, the residents suspect it to be a consequence of the crisis. The paper discusses how market forces interact with the material surroundings we inhabit and explores the relationship between controlled and uncontrollable in the design of places....

  7. Secret Places.

    Science.gov (United States)

    Ridolfi, Kerry

    1997-01-01

    Argues that children are as deep as the ocean, with secret places inside of them waiting to be opened. Notes that it is powerful for students to learn they can make sense of the world through words, and describes inviting them into poetry as they read poetry, create poetry packets, and write and revise poems. (SR)

  8. Envisioning place

    DEFF Research Database (Denmark)

    Schmidt, Garbi; Glick Schiller, Nina

    2016-01-01

    together, the articles contribute to an emerging relational social science by approaching urban sociabilities through four interrelated parameters: (1) a concept of place-making situated within trajectories of differential and multiscalar power; (2) a discursive analysis of narratives and silences...

  9. Cloning vector

    Science.gov (United States)

    Guilfoyle, Richard A.; Smith, Lloyd M.

    1994-01-01

    A vector comprising a filamentous phage sequence containing a first copy of filamentous phage gene X and other sequences necessary for the phage to propagate is disclosed. The vector also contains a second copy of filamentous phage gene X downstream from a promoter capable of promoting transcription in a bacterial host. In a preferred form of the present invention, the filamentous phage is M13 and the vector additionally includes a restriction endonuclease site located in such a manner as to substantially inactivate the second gene X when a DNA sequence is inserted into the restriction site.

  10. Cloning vector

    Science.gov (United States)

    Guilfoyle, R.A.; Smith, L.M.

    1994-12-27

    A vector comprising a filamentous phage sequence containing a first copy of filamentous phage gene X and other sequences necessary for the phage to propagate is disclosed. The vector also contains a second copy of filamentous phage gene X downstream from a promoter capable of promoting transcription in a bacterial host. In a preferred form of the present invention, the filamentous phage is M13 and the vector additionally includes a restriction endonuclease site located in such a manner as to substantially inactivate the second gene X when a DNA sequence is inserted into the restriction site. 2 figures.

  11. Places Connected:

    DEFF Research Database (Denmark)

    Hansen, Annette Skovsted

    This paper argues that development assistance contributed to the globalization of the 20th century by financing truly global networks of people. By focusing on the networks financed by development assistance bound by the national histories of Denmark and Japan, I illustrate how the people who...... experiences of place, however, when it is often the same people who experience many different places? Along with many other so-called donors in the 1950s, Denmark and Japan chose to invest in the education of own and other nationals involved in development and thereby financed personal connections between...... individuals throughout the world. Development assistance , where there are two or three links only between a Bangladeshi farmer, a street child in Sao Paolo and the President of the United States, the Queen of Denmark, or a suburban house wife in Japan, who has never left the Osaka area, but mothered a United...

  12. Places available**

    CERN Multimedia

    2003-01-01

    If you wish to participate in one of the following courses, please discuss with your supervisor and apply electronically directly from the course description pages that can be found on the Web at: http://www.cern.ch/Training/ or fill in an "application for training" form available from your Divisional Secretariat or from your DTO (Divisional Training Officer). Applications will be accepted in the order of their receipt. TECHNICAL TRAINING Monique Duval tel. 74924 technical.training@cern.ch ** The number of places available may vary. Please check our Web site to find out the current availability. Places are available in the following courses: ACCESS 2000 - niveau 1 : 13 & 14.11.03 (2 jours) C++ for Particle Physicists : 17 – 21.11.03 (6 X 3-hour lectures) Programmation automate Schneider TSX Premium – niveau 2 : 18 – 21.11.03 (4 jours) JAVA 2 Enterprise Edition – Part 1 : WEB Applications : 20 & ...

  13. Equivalent Vectors

    Science.gov (United States)

    Levine, Robert

    2004-01-01

    The cross-product is a mathematical operation that is performed between two 3-dimensional vectors. The result is a vector that is orthogonal or perpendicular to both of them. Learning about this for the first time while taking Calculus-III, the class was taught that if AxB = AxC, it does not necessarily follow that B = C. This seemed baffling. The…

  14. Places available

    CERN Multimedia

    2004-01-01

    If you wish to participate in one of the following courses, please discuss with your supervisor and apply electronically directly from the course description pages that can be found on the Web at: http://www.cern.ch/Training/ or fill in an "application for training" form available from your Divisional Secretariat or from your DTO (Divisional Training Officer). Applications will be accepted in the order of their receipt. Places available The number of places available may vary. Please check our Web site to find out the current availability. Places are available in the following courses : Introduction à Outlook : 19.8.2004 (1 journée) Outlook (short course I) : E-mail : 31.8.2004 (2 hours, morning) Outlook (short course II) : Calendar, Tasks and Notes : 31.8.2004 (2 hours, afternoon) Instructor-led WBTechT Study or Follow-up for Microsoft Applications : 7.9.2004 (morning) Outlook (short course III) : Meetings and Delegation : 7.9.2004 (2 hours, afternoon) Introduction ...

  15. Places disponibles*/Places available **

    CERN Multimedia

    2003-01-01

    Des places sont disponibles dans les cours suivants : Places are available in the following course : Java 2 Enterprise Edition - Part 2 : Enterprise JavaBeans : 20 - 22.1.03 (3 days) Introduction to PVSS : 27.1.03 (Afternoon) free course but registration necessary Basic PVSS : 28 - 30.1.03 (3 days) MAGNE-03 - Magnétisme pour l'électrotechnique : 28 - 30.1.03 (3 jours) MAGNE-03 - Magnetism for Technical Electronics : 11 - 13.2.03 (3 days) AutoCAD 2002 - niveau 1 : 24, 25.2 et 3, 4.3.03 (4 jours) AutoCAD 2002 - niveau 2 : 10 & 11.3.03 (2 jours) C++ for Particle Physicists : 10 - 14.3.03 (6 X 3 hour lectures) AutoCAD Mechanical 6 PowerPack (F) : 12, 13, 17, 18, 24 & 25.3.03 (6 jours) * Etant donné le délai d'impression du Bulletin, ces places peuvent ne plus être disponibles au moment de sa parution. Veuillez consulter notre site Web pour avoir la dernière mise à jour. ** The number of places available may vary. Please check our Web site to find out the current availability. Si vous désirez ...

  16. Wind energy

    International Nuclear Information System (INIS)

    Anon.

    1992-01-01

    This chapter discusses the role wind energy may have in the energy future of the US. The topics discussed in the chapter include historical aspects of wind energy use, the wind energy resource, wind energy technology including intermediate-size and small wind turbines and intermittency of wind power, public attitudes toward wind power, and environmental, siting and land use issues

  17. Fixture for winding transformers

    Science.gov (United States)

    Mclyman, M. T.

    1980-01-01

    Bench-mounted fixture assists operator in winding toroid-shaped transformer cores. Toroid is rigidly held in place as wires are looped around. Arrangement frees both hands for rapid winding and untangling of wires that occurs when core is hand held.

  18. Three-Dimensional Wind Profiling of Offshore Wind Energy Areas With Airborne Doppler Lidar

    Science.gov (United States)

    Koch, Grady J.; Beyon, Jeffrey Y.; Cowen, Larry J.; Kavaya, Michael J.; Grant, Michael S.

    2014-01-01

    A technique has been developed for imaging the wind field over offshore areas being considered for wind farming. This is accomplished with an eye-safe 2-micrometer wavelength coherent Doppler lidar installed in an aircraft. By raster scanning the aircraft over the wind energy area (WEA), a three-dimensional map of the wind vector can be made. This technique was evaluated in 11 flights over the Virginia and Maryland offshore WEAs. Heights above the ocean surface planned for wind turbines are shown to be within the marine boundary layer, and the wind vector is seen to show variation across the geographical area of interest at turbine heights.

  19. Places available**

    CERN Multimedia

    Places are available in the following courses: Hands-on Introduction to Python Programming: 11-13.08.2003 (3 days) Introduction to the CERN Engineering Data Management System (EDMS): 26.08.2003 (1 day) The CERN Engineering Data Management System (EDMS) for Engineers: 27.08.2003 (1 day) CLEAN-2002 : Travailler en salle blanche : 4.09.2003 (une demi-journée) AutoCAD 2002 - Level 1: 4, 5, 15, 16.09.2003 (2 x 2 days) AutoCAD Mechanical 6 PowerPack : 17, 18, 25, 26.09.2003 et 2, 3.10.2003 (3 x 2 journées, français) AutoCAD 2002 - niveau 1 : 23, 24, 30.09.2003 et 1.10.2003 (2 x 2 journées) Introduction to the CERN Engineering Data Management System (EDMS): 23.09.2003 (1 day) The CERN Engineering Data Management System (EDMS) for Local Administrators: 24-25.09.2003 (2 days) AutoCAD 2002 - niveau 2 : 8 et 10.10.2003 (2 journées) CLEAN-2002: Working in a Cleanroom: 23.10.2003 (half day, p.m.) ** The number of places available may vary. Please check our Web site to find out the current availabili...

  20. Places available**

    CERN Multimedia

    2003-01-01

    Places are available in the following courses: Hands-on Introduction to Python Programming: 11-13.08.2003(3 days) Introduction to the CERN Engineering Data Management System (EDMS): 26.08.2003 (1 day) The CERN Engineering Data Management System (EDMS) for Engineers: 27.08.2003 (1 day) CLEAN-2002 : Travailler en salle blanche : 4.09.2003 (une demi-journée) AutoCAD 2002 - Level 1: 4, 5, 15, 16.09.2003 (2 x 2 days) AutoCAD Mechanical 6 PowerPack : 17, 18, 25, 26.09.2003 et 2, 3.10.2003 (3 x 2 journées, français) AutoCAD 2002 - niveau 1 : 23, 24, 30.09.2003 et 1.10.2003 (2 x 2 journées) Introduction to the CERN Engineering Data Management System (EDMS): 23.09.2003 (1 day) The CERN Engineering Data Management System (EDMS) for Local Administrators: 24-25.09.2003 (2 days) AutoCAD 2002 - niveau 2 : 8 et 10.10.2003 (2 journées) CLEAN-2002: Working in a Cleanroom: 23.10.2003 (half day, p.m.) ** The number of places available may vary. Please ch...

  1. Media places

    DEFF Research Database (Denmark)

    Linde, Per; Messeter, Jörn

    The impact that ubiquitous wireless network technologies and mobile phones have on our experience of the modern cityscape, has been a driving force in many research projects in recent years. The agendas differ in relation to perspectives, but it seems safe to claim that such technologies are no l......The impact that ubiquitous wireless network technologies and mobile phones have on our experience of the modern cityscape, has been a driving force in many research projects in recent years. The agendas differ in relation to perspectives, but it seems safe to claim that such technologies...... construction of place in the urban setting. The concept of Hertzian space, put forth by Anthony Dunne and others (Dunne, 1999) also carries a dimension of how spaces of wireless communication may be problematized, and how we can criticize cultural phenomena taken for granted through innovative technology. From...... this perspective wireless technology can also be a way of temporarily appropriating places within the city space for a variety of different groups, at times questioning hierarchical structures of ownership of public spaces. These spaces can be said to be hybrid spaces, bringing forth the fundamental question...

  2. Places available**

    CERN Multimedia

    2003-01-01

    If you wish to participate in one of the following courses, please discuss with your supervisor and apply electronically directly from the course description pages that can be found on the Web at: http://www.cern.ch/Training/ or fill in an "application for training" form available from your Divisional Secretariat or from your DTO (Divisional Training Officer). Applications will be accepted in the order of their receipt. TECHNICAL TRAINING Monique Duval Tel. 74924technical.training@cern.ch ** The number of places available may vary. Please check our Web site to find out the current availability. Places are available in the following courses: MATLAB Fundamentals and Programming Techniques (ML01) : 2 & 3.12.03 (2 days) Oracle 8i : SQL : 3 - 5.12.03 (3 days) The EDMS MTF in practice : 5.12.03 (afternoon, free of charge) Modeling Dynamic Systems with Simulink (SL01) : 8 & 9.12.03 (2 days) Signal Processing with MATLAB (SG01) : 11 & 12.12.03 (2 days) The JAVA Programming Language - l...

  3. Places available**

    CERN Multimedia

    2003-01-01

    If you wish to participate in one of the following courses, please discuss with your supervisor and apply electronically directly from the course description pages that can be found on the Web at: http://www.cern.ch/Training/ or fill in an "application for training" form available from your Divisional Secretariat or from your DTO (Divisional Training Officer). Applications will be accepted in the order of their receipt. TECHNICAL TRAINING Monique Duval tel. 74924 technical.training@cern.ch ** The number of places available may vary. Please check our Web site to find out the current availability. Places are available in the following courses: MATLAB Fundamentals and Programming Techniques (ML01) :2 & 3.12.03 (2 days) Oracle 8i : SQL : 3 - 5.12.03 (3 days) The EDMS MTF in practice : 5.12.03 (afternoon, free of charge) Modeling Dynamic Systems with Simulink (SL01) : 8 & 9.12.03 (2 days) Signal Processing with MATLAB (SG01) : 11 & ...

  4. Places available**

    CERN Multimedia

    2004-01-01

    If you wish to participate in one of the following courses, please discuss with your supervisor and apply electronically directly from the course description pages that can be found on the Web at: http://www.cern.ch/Training/ or fill in an "application for training" form available from your Divisional Secretariat or from your DTO (Divisional Training Officer). Applications will be accepted in the order of their receipt.TECHNICAL TRAINING Monique Duval tel. 74924 technical.training@cern.ch ** The number of places available may vary. Please check our Web site to find out the current availability. Places are available in the following courses: The JAVA Programming Language Level 1 : 9 & 10.1.2004 (2 days) The JAVA Programming Language Level 2 : 11 to 13.1.2004 (3 days) LabVIEW base 1 : 25 - 27.2.2004 (3 jours) CLEAN-2002 : Working in a Cleanroom : 10.3.2004 (afternoon - free of charge) C++ for Particle Physicists : 8 - 12.3.2004 ( 6 X 4-hour sessions) LabVIEW Basics 1 : 22 - 24.3.20...

  5. Places available**

    CERN Document Server

    2004-01-01

    If you wish to participate in one of the following courses, please discuss with your supervisor and apply electronically directly from the course description pages that can be found on the Web at: http://www.cern.ch/Training/ or fill in an "application for training" form available from your Divisional Secretariat or from your DTO (Divisional Training Officer). Applications will be accepted in the order of their receipt. TECHNICAL TRAINING Monique Duval tel. 74924 technical.training@cern.ch ** The number of places available may vary. Please check our Web site to find out the current availability. Places are available in the following courses: The JAVA Programming Language Level 1 :9 & 10.1.2004 (2 days) The JAVA Programming Language Level 2 : 11 to 13.1.2004 (3 days) Hands-on Introduction to Python Programming : 16 - 18.2.2004 (3 days - free of charge) CLEAN-2002 : Working in a Cleanroom : 10.3.2004 (afternoon - free of charge) C++ for Particle Physicists : 8 - 12.3.2004...

  6. Places available**

    CERN Document Server

    2003-01-01

    If you wish to participate in one of the following courses, please discuss with your supervisor and apply electronically directly from the course description pages that can be found on the Web at: http://www.cern.ch/Training/ or fill in an "application for training" form available from your Divisional Secretariat or from your DTO (Divisional Training Officer). Applications will be accepted in the order of their receipt. TECHNICAL TRAINING Monique Duval Tel. 74924 technical.training@cern.ch ** The number of places available may vary. Please check our Web site to find out the current availability. Places are available in the following courses: JAVA 2 Enterprise Edition - Part 1 : WEB Applications : 20 & 21.11.03(2 days) FrontPage 2000 - niveau 1 : 20 & 21.11.03 (2 jours) Oracle 8i : SQL : 3 - 5.12.03 (3 days) Oracle 8i : Programming with PL/SQL : 8 - 10.12.03 (3 days) The JAVA Programming Language - leve...

  7. Places available**

    CERN Multimedia

    2003-01-01

    If you wish to participate in one of the following courses, please discuss with your supervisor and apply electronically directly from the course description pages that can be found on the Web at: http://www.cern.ch/Training/ or fill in an "application for training" form available from your Divisional Secretariat or from your DTO (Divisional Training Officer). Applications will be accepted in the order of their receipt. TECHNICAL TRAINING Monique Duval tel. 74924 technical.training@cern.ch ** The number of places available may vary. Please check our Web site to find out the current availability. Places are available in the following courses: Project Planning with MS-Project : 15 & 22.1.2004 (2 days) Joint PVSS JCOP Framework Course : 2 sessions : 2 - 6.2.2004 and 16 - 20-2-2004 (5 days) Hands-on Introduction to Python Programming : 16 - 18.2.2004 (3 days - free of charge) C++ for Particle Physicists : 8 - 12.3.2004 ( 6 X 4-hour sessions)

  8. Places available **

    CERN Multimedia

    2003-01-01

    Des places sont disponibles dans les cours suivants : Places are available in the following courses : WorldFIP 2003 pour utilisateurs : 11-14.2.03 (4 jours) DISP-2003 ? Spring I Term : Introduction to Digital Signal Processing : 20, 27.2, 6, 13, 20, 27.3, 3.4.03 (7 X 2-hour lectures) AXEL-2003 - Introduction to Accelerators : 24-28.2.03 (10 X 1-hour lectures) AutoCAD 2002 - niveau 1 : 24, 25.2 & 3, 4.3.03 (4 jours) Introduction à Windows 2000 au CERN : 25.2.03 (1/2 journée) LabView base 2/LabView Basics 2 : 10 & 11.3.03 (2 jours/2 days) langue à définir/Language to be decided C++ for Particle Physicists : 10 ? 14.3.03 (6 X 3-hour lectures) Introduction to PVSS : 10.3.03 (half day, afternoon) Basic PVSS : 11 - 13.3.03 (3 days) LabView avancé /LabView Advanced : 12 - 14.3.03 (3 jours/3days) Langue à définir/language to be decided AutoCAD Mechanical 6 PowerPack (F) : 12, 13, 17, 18, 24 & 25.3.03 (6 jours) PVSS - JCOP Framework Tutorial : 14.3.03 (1 day) MAGNE-03 - Magnetism for Technical Ele...

  9. Places available **

    CERN Multimedia

    2003-01-01

    Des places sont disponibles dans les cours suivants : Places are available in the following courses : Introduction à Windows 2000 au CERN : 25.2.03 (1/2 journée) LabView base 2/LabView Basics 2 : 10 & 11.3.03 (2 jours/2 days) langue à définir/Language to be decided C++ for Particle Physicists : 10 - 14.3.03 (6 X 3-hour lectures) Introduction to PVSS : 10.3.03 (half day, afternoon) Basic PVSS : 11 - 13.3.03 (3 days) LabView avancé /LabView Advanced : 12 - 14.3.03 (3 jours/3days) Langue à définir/Language to be decided AutoCAD Mechanical 6 PowerPack (F) : 12, 13, 17, 18, 24 & 25.3.03 (6 jours) PVSS - JCOP Framework Tutorial : 14.3.03 (1 day) CLEAN-2002 : Working in a cleanroom : 2.4.03 (half-day, afternoon, free course, registration required) LabView base 1/LabView Basics 1 : 9 - 11.4.03 (3 jours/3 days) Langue à définir/Language to be decided DISP-2003 - Spring II Term : Advanced Digital Signal Processing : 30.4, 7, 14, 21.5.03 (4 X 2-hour lectures) AutoCAD 2002 - niveau 2 : 5 & 6.5.03 (...

  10. Places available **

    CERN Multimedia

    2003-01-01

    Des places sont disponibles dans les cours suivants : Places are available in the following courses : DISP-2003 - Spring I Term : Introduction to Digital Signal Processing : 20, 27.2, 6, 13, 20, 27.3, 3.4.03 (7 X 2-hour lectures) AXEL-2003 - Introduction to Accelerators : 24 - 28.2.03 (10 X 1-hour lectures) AutoCAD 2002 - niveau 1 : 24, 25.2 & 3, 4.3.03 (4 jours) Introduction à Windows 2000 au CERN : 25.2.03 (1/2 journée) LabView base 2/LabView Basics 2 : 10 & 11.3.03 (2 jours/2 days) langue à définir/Language to be decided C++ for Particle Physicists : 10 - 14.3.03 (6 X 3-hour lectures) Introduction to PVSS : 10.3.03 (half day, afternoon) Basic PVSS : 11 - 13.3.03 (3 days) LabView avancé /LabView Advanced : 12 - 14.3.03 (3 jours/3days) Langue à définir/language to be decided AutoCAD Mechanical 6 PowerPack (F) : 12, 13, 17, 18, 24 & 25.3.03 (6 jours) PVSS - JCOP Framework Tutorial : 14.3.03 (1 day) CLEAN-2002 : Working in a cleanroom : 2.4.03 (half-day, afternoon, free course, regis...

  11. Places available **

    CERN Multimedia

    2003-01-01

    Des places sont disponibles dans les cours suivants : Places are available in the following courses : C++ for Particle Physicists : 10 - 14.3.03 (6 X 3-hour lectures) Introduction to PVSS : 10.3.03 (half day, afternoon) Basic PVSS : 11 - 13.3.03 (3 days) PVSS - JCOP Framework Tutorial : 14.3.03 (1 day) CLEAN-2002 : Working in a cleanroom : 2.4.03 (half-day, afternoon, free course, registration required) LabView base 1/LabView Basics 1 : 9 - 11.4.03 (3 jours/3 days) Langue à définir/language to be decided DISP-2003 - Spring II Term : Advanced Digital Signal Processing : 30.4, 7, 14, 21.5.03 (4 X 2-hour lectures) AutoCAD 2002 - niveau 1 : 29, 30.4 et 7, 8.5.03 (4 jours) AutoCAD 2002 - niveau 2 : 5 & 6.5.03 (2 jours) AutoCAD Mechanical 6 PowerPack (F) : 12, 13, 20, 21, 27 & 28.5.03 (6 jours) Formation Siemens SIMATIC /Siemens SIMATIC Training : Introduction à STEP7 /Introduction to STEP7 : 11 & 12.3.03 / 3 & 4.6.03 (2 jours/2 days) Programmation STEP7/STEP7 Programming : 31.3 - 4.4.03 / 16...

  12. Places available**

    CERN Multimedia

    2003-01-01

    Places are available in the following courses: Conception de PCB rapides dans le flot Cadence : 11.6.03 (matin) EXCEL 2000 - level 1 : 12 & 13.6.03 (2 days) Introduction to PVSS : 16.6.03 (p.m.) Basic PVSS : 17 - 19.6.03 (3 days) Réalisation de PCB rapides dans le flot Cadence : 17.6.03 (matin) PVSS - JCOP Framework Tutorial : 20.6.03 (1 day) Programmation automate Schneider : Programmation automate Schneider TSX Premium - 2ème niveau : 24 - 27.6.03 (4 jours) - audience : toute personne qui veux maitriser la mise en uvre et la programmation des fonctions spécialisées d'un automate TSX Premium - objectifs : maitriser la mise en uvre et la programmation des fonctions spécialisées d'un automate TSX Premium Cours de sécurité : Etre TSO au CERN : Prochaines sessions : 24, 25 & 27.6.03 - 4, 5 & 7.11.03 (session de 3 jours) ** The number of places available may vary. Please check our Web site to find out the current availability. If you wish to participate in one of these courses, pl...

  13. Places available**

    CERN Multimedia

    2003-01-01

    If you wish to participate in one of these courses, please discuss with your supervisor and apply electronically directly from the course description pages that can be found on the Web at: http://www.cern.ch/Training/ or fill in an "application for training" form available from your Divisional Secretariat or from your DTO (Divisional Training Officer). Applications will be accepted in the order of their receipt. ** The number of places available may vary. Please check our Web site to find out the current availability. Places are available in the following courses : EXCEL 2000 - niveau 1 : 20 & 22.10.03 (2 jours) CLEAN-2002 : Working in a Cleanroom (free of charge) : 23.10.03 (half day) The EDMS-MTF in practice (free of charge) :  28 -  30.10.03 (6 half-day sessions) AutoCAD 2002 - Level 1 : 3, 4, 12, 13.11.03 (4 days) LabVIEW TestStand ver. 3 : 4 & 5.11.03 (2 days) Introduction to Pspice : 4.11.03 p.m. (half-day) Hands-on Introduction to Python Programm...

  14. PLACES AVAILABLE

    CERN Multimedia

    Enseignement Technique; Tél. 74924; Technical Training; Monique Duval; Tel. 74924

    2000-01-01

    Places available Places are available in the following courses:   LabView hands-on 13.11.00 4 hours LabView Basics 1 14 - 16.11.00 3 days Nouveautés de WORD 19 et 20.10.00 2 jours ACCESS 1er niveau 30 - 31.10.00 2 jours Advanced aspects of the C language 2 - 3.11.00 2 days Introduction to Oracle SQL and PL/SQL 13 - 17.11.00 5 days C++ for Particle Physicists 20 - 24.11.00 6 lectures Develop PL/SQL Program Units 20 - 22.11.00 3 days Oracle Application Server Develop Web-Based Applications with PL/SQL 27 - 28.11.00 2 days Programmation TSX Premium 1 28.11 - 1.12.00 4 jours Programmation TSX Premium 2 12 - 15.12.00 4 jours If you wish to participate in one of these courses, please discuss with your supervisor and apply electronically directly from the course description pages that can be found on the Web at : http://www.cern.ch/Training/ or fill in an “application for training” form available from your Divisional Secretariat or from your DTO (Divisional Training Offi...

  15. Circular Conditional Autoregressive Modeling of Vector Fields.

    Science.gov (United States)

    Modlin, Danny; Fuentes, Montse; Reich, Brian

    2012-02-01

    As hurricanes approach landfall, there are several hazards for which coastal populations must be prepared. Damaging winds, torrential rains, and tornadoes play havoc with both the coast and inland areas; but, the biggest seaside menace to life and property is the storm surge. Wind fields are used as the primary forcing for the numerical forecasts of the coastal ocean response to hurricane force winds, such as the height of the storm surge and the degree of coastal flooding. Unfortunately, developments in deterministic modeling of these forcings have been hindered by computational expenses. In this paper, we present a multivariate spatial model for vector fields, that we apply to hurricane winds. We parameterize the wind vector at each site in polar coordinates and specify a circular conditional autoregressive (CCAR) model for the vector direction, and a spatial CAR model for speed. We apply our framework for vector fields to hurricane surface wind fields for Hurricane Floyd of 1999 and compare our CCAR model to prior methods that decompose wind speed and direction into its N-S and W-E cardinal components.

  16. Place identity and place scale: the impact of place salience.

    OpenAIRE

    Bernardo, Fátima; Palma-Oliveira, José-Manuel

    2013-01-01

    Research about place, place identity and attachment supports the idea that bonds with places may differ depending on the place scale. Based on the view that identity is context-dependent, this paper brings to the table the impact of manipulating the salience of place on the intensity of place identity and place attachment reported. A study was designed to examine place identity and place attachment in two groups of residents (permanent and temporary) at three different scales (nei...

  17. PLACES AVAILABLE

    CERN Multimedia

    Technical Training; Tel. 74924

    2001-01-01

    Places are available in the following courses: Introduction to Databases :  3 - 4.7.01 (2 days) The JAVA programming language Level 2 : 4 - 6.7.01 (3 days) Enterprise JavaBeans :  9 - 11.7.01 (3 days) Design Patterns :  10 - 12.7.01 (3 days) C++ for Particle Physicists :  23 - 27.7.01 (6 3-hour lectures) If you wish to participate in one of these courses, please discuss with your supervisor and apply electronically directly from the course description pages that can be found on the Web at : http://www.cern.ch/Training/ or fill in an 'application for training' form available from your Divisional Secretariat or from your DTO (Divisional Training Officer). Applications will be accepted in the order of their receipt.

  18. PLACES AVAILABLE

    CERN Multimedia

    Technical Training; Tel. 74924

    2001-01-01

    Places are available in the following courses: Introduction to Perl 5 : 2 - 3.7.01 (2 days) Introduction to Databases :  3 - 4.7.01 (2 days) JAVA programming language Level 2 : 4 - 6.7.01 (3 days) Enterprise JavaBeans :  9 - 11.7.01 (3 days) Design Patterns :  10 - 12.7.01 (3 days) C++ for Particle Physicists :  23 - 27.7.01 (6 3-hour lectures) If you wish to participate in one of these courses, please discuss with your supervisor and apply electronically directly from the course description pages that can be found on the Web at : http://www.cern.ch/Training/ or fill in an 'application for training' form available from your Divisional Secretariat or from your DTO (Divisional Training Officer). Applications will be accepted in the order of their receipt.

  19. PLACES AVAILABLE

    CERN Multimedia

    Monique Duval

    2002-01-01

    Places are available in the following courses: CLEAN-2002 : Travailler en salle blanche (cours gratuit) : 13.08.2002 (matin) Introduction to the CERN Enginnering Data Management System :  27.8.02  (1 day) The CERN Engineering Data Management System for Advanced Users :  28.8.02  (1 day) If you wish to participate in one of these courses, please discuss with your supervisor and apply electronically directly from the course description pages that can be found on the Web at : Technical Training or fill in an 'application for training' form available from your Divisional Secretariat or from your DTO (Divisional Training Officer). Applications will be accepted in the order of their receipt. Technical Training Monique Duval Tel.74924 monique.duval@cern.ch    

  20. PLACES AVAILABLE

    CERN Multimedia

    Monique Duval

    2002-01-01

    Places are available in the following courses: C++ Programming Level 2 - Traps & Pitfalls:  16 - 19.7.02 (4 days) Frontpage 2000 - level 1 :  22 - 23.7.02  (2 days) Introduction à Windows 2000 au CERN : 24.7.02 (après-midi) CLEAN-2002 : Travailler en salle blanche (cours gratuit) : 13.08.2002 (matin) If you wish to participate in one of these courses, please discuss with your supervisor and apply electronically directly from the course description pages that can be found on the Web at : Technical Training or fill in an 'application for training' form available from your Divisional Secretariat or from your DTO (Divisional Training Officer). Applications will be accepted in the order of their receipt. Technical Training Monique Duval Tel.74924 monique.duval@cern.ch

  1. Placing knowledge

    DEFF Research Database (Denmark)

    Adriansen, Hanne Kirstine; Valentin, Karen; Nielsen, Gritt B.

    ; on the other hand, the rationale for strengthening mobility through internationalisation is based on an imagination of the potentials of particular locations (academic institutions). Intrigued by this tension between universality and particularity in academic knowledge production, this paper presents...... preliminary findings from a project that study internationalisation of higher education as an agent in the interrelated processes of place-making and knowledge-making. The project is based on three case-studies. In this paper, focus is on PhD students’ change of research environment. This is used as a case......Internationalisation of higher education is premised by a seeming paradox: On the one hand, academic knowledge strives to be universal in the sense that it claims to produce generalizable, valid and reliable knowledge that can be used, critiqued, and redeveloped by academics from all over the world...

  2. PLACES AVAILABLE

    CERN Multimedia

    Monique Duval

    2002-01-01

    Places are available in the following courses: December 2002   PCAD Schémas - Débutants :  5 & 6.12.02  (2 jours) PCAD PCB - Débutants :  9 - 11.12.02  (3 jours) FrontPage 2000 - level 1:  9 & 10.12.02  (2 days) Introduction à la CAO Cadence (cours gratuit) :  10 & 11.12.02  (2 jours) If you wish to participate in one of these courses, please discuss with your supervisor and apply electronically directly from the course description pages that can be found on the Web at : Technical Training or fill in an 'application for training' form available from your Divisional Secretariat or from your DTO (Divisional Training Officer). Applications will be accepted in the order of their receipt. Technical Training Monique Duval Tel.74924 monique.duval@cern.ch

  3. Vector geometry

    CERN Document Server

    Robinson, Gilbert de B

    2011-01-01

    This brief undergraduate-level text by a prominent Cambridge-educated mathematician explores the relationship between algebra and geometry. An elementary course in plane geometry is the sole requirement for Gilbert de B. Robinson's text, which is the result of several years of teaching and learning the most effective methods from discussions with students. Topics include lines and planes, determinants and linear equations, matrices, groups and linear transformations, and vectors and vector spaces. Additional subjects range from conics and quadrics to homogeneous coordinates and projective geom

  4. Wind Turbine Acoustic Day 2018

    DEFF Research Database (Denmark)

    Mogensen, Jesper; Søndergaard, Bo; Hünerbein, Sabine Von

    The bi-annual event entitled Wind Turbine Acoustic Day dealing with wind turbine noise issues organized by DTU Wind Energy took place on May, 17th 2018 as its third edition. The abstracts and slides for the presentations are reported....

  5. Offshore Wind Farms

    DEFF Research Database (Denmark)

    Lundtang Petersen, Erik; Hasager, Charlotte Bay; Courtney, Michael

    2015-01-01

    : the rotor, the nacelle, the tower, and the foundation. Further the determinations of the essential environmental conditions are treated: the wind field, the wave field, the sea current, and the soil conditions. The various options for grid connections, advantages, and disadvantages are discussed. Of special...... concern are the problems associated with locating the turbines close together in a wind farm and the problems of placing several large wind farms in a confined area. The environmental impacts of offshore wind farms are also treated, but not the supply chain, that is, the harbors, the installation vessels...

  6. Wind Energy Facilities

    Energy Technology Data Exchange (ETDEWEB)

    Laurie, Carol

    2017-02-01

    This book takes readers inside the places where daily discoveries shape the next generation of wind power systems. Energy Department laboratory facilities span the United States and offer wind research capabilities to meet industry needs. The facilities described in this book make it possible for industry players to increase reliability, improve efficiency, and reduce the cost of wind energy -- one discovery at a time. Whether you require blade testing or resource characterization, grid integration or high-performance computing, Department of Energy laboratory facilities offer a variety of capabilities to meet your wind research needs.

  7. Places available **

    CERN Multimedia

    2003-01-01

    Places are available in the following courses: PIPES-2003 - Pratique du Sertissage de tubes métalliques et multicouches : 26.8.03 (stage pratique) The CERN Engineering Data Management System (EDMS) for Engineers : 27.8.03 (1 day, free of charge) CLEAN-2002 : Travailler en salle blanche : 4.9.03 (une demi-journée, séminaire gratuit) The CERN Engineering Data Management System (EDMS) for Local Administrators : 24 & 25.9.03 (2 days, free of charge) Siemens SIMATIC Training : Programmation STEP7 - niveau 1 : 29 - 2.10.03 (4 jours) - ouverture des inscriptions fin août Programmation STEP7 - niveau 2 : 13 - 17.10.03 (5 jours) - ouverture des inscriptions fin août Réseau Simatic Net : 22 & 23.10.03 (2 jours) - ouverture des inscriptions fin août CLEAN-2002 : Working in a Cleanroom : 23.20.03 (half day, free of charge) These courses will be given in French or Englis...

  8. Places available**

    CERN Document Server

    2003-01-01

    Places are available in the following courses : FrontPage 2000 - niveau 1: 20 & 21.5.03 (2 jours) PIPES-2003 : Pratique du sertissage de tubes métalliques et multicouches: 21.5.03 (1 jour) Introduction à la CAO Cadence: de la saisie de schéma Concept-HDL au PCB : 20 & 22.5.03 (2 jours) AutoCAD Mechanical 6 PowerPack (E): 5, 6, 12, 13, 26, 27.6.03 (6 days) EXCEL 2000 - niveau 1: 10 & 11.6.03 (2 jours) Conception de PCB rapides dans le flot Cadence: 11.6.03 (matin) EXCEL 2000 - level 1: 12 & 13.6.03 (2 days) Introduction to PVSS: 16.6.03 (half-day, pm) Basic PVSS: 17 - 19.6.03 (3 days) Réalisation de PCB rapides dans le flot Cadence: 17.6.03 (matin) LabView DSC (language to be defined): 19 & 20.6.03 PVSS - JCOP Framework Tutorial: 20.6.03 (1 day) EXCEL 2000 - niveau 2: 24 & 25.6.03 (2 jours) Siemens SIMATIC Training: Introduction to STEP7: 3 & 4.6.03 (2 days) STEP7 Programming: 16 - 20.6.03 (5 days) Simatic Net Network: 26 & 27.6.03 (2 days) These courses will be given...

  9. PLACES AVAILABLE

    CERN Multimedia

    Monique Duval

    2002-01-01

    Places are available in the following courses: LabView Hands-on (bilingue/bilingual - gratuit/free of charge) : 13.9.02 (a.m.) LabView DAQ Hands-on (bilingue/bilingual - gratuit/free of charge) : 13.9.02 (p.m.) AutoCAD 2002 - niveau 1 : 19, 20, 26, 27.9.02 (4 jours) LabView Base 1 : 23 - 25.9.02 (3 jours) LabView DAQ (E) : 26 - 27.9.02 (2 days) AutoCAD Mechanical 6 PowerPack (F) : 30.9, 1, 2, 9, 10, 11.10.02 (6 jours) CLEAN-2002 : Working in a Cleanroom (free of charge) : 10.10.02 (half-day, p.m.) AutoCAD 2002 - niveau 2 : 14 - 15.10.02 (2 jours) AutoCAD 2002 - Level 1 : 17, 18, 24, 25.10.02 (4 days) If you wish to participate in one of these courses, please discuss with your supervisor and apply electronically directly from the course description pages that can be found on the Web at : Technical Training or fill in an 'application for training' form available from your Divisional Secretariat or from your DTO (Divisional Training Of...

  10. PLACES AVAILABLE

    CERN Multimedia

    Monique Duval

    2002-01-01

    Places are available in the following courses: Introduction to Oracle 8i : SQL and PL/SQL:  7 - 11.10.02  (5 days) CLEAN-2002 : Working in a Cleanroom (free of charge):  10.10.02  (half-day, p.m.) AutoCAD 2002 - niveau 2 :  14 - 15.10.02  (2 jours) Introduction à DesignSpace :  16.10.02  (1 journée) Introduction to DesignSpace:  17.10.02  (1 day) AutoCAD 2002 - Level 1:  17, 18, 24, 25.10.02  (4 days) AutoCAD Mechanical 6 PowerPack (F) :  21, 22, 23.10 et 4, 5, 6.11.02  (6 jours) Introduction à ANSYS/Introduction to ANSYS (langue à définir suivant demande/ Language to be chosen according to demand):  21 - 25.10.02  (5 jours/days) HREF-2002: Helium Refrigeration Techniques (English-French, bilingual) :  21 - 25.10.2002  (7 half days) HREF-2002: Techniques de la Réfri...

  11. Places available**

    CERN Document Server

    2003-01-01

    Places are available in the following courses : The CERN EDMS for Local Administrators : 24 & 25.9.03 (2 days, free of charge) HeREF-2003 : Techniques de la réfrigération Hélium (cours en français avec support en anglais) : 6 - 10.10.2003 (7 demi-journées) The Java Programming Language Level 1 : 6 - 7.10.2003 (2 days) Java 2 Enterprise Edition - Part 2 : Enterprise JavaBeans : 8 - 10.10.2003 (3 days) FileMaker - niveau 1 : 9 & 10.10.03 (2 jours) EXCEL 2000 - niveau 1 : 20 & 22.10.03 (2 jours) AutoCAD 2002 - niveau 1 : 20, 21, 27, 28.10.03 (4 jours) CLEAN-2002 : Working in a Cleanroom : 23.10.03 (half day, free of charge) AutoCAD 2002 - Level 1 : 3, 4, 12, 13.11.03 (4 days) AutoCAD 2002 - niveau 2 : 10 & 11.11.03 (2 jours) ACCESS 2000 - niveau 1 : 13 & 14.11.03 (2 jours) AutoCAD Mechanical 6 PowerPack (E) : 17, 18, 24, 25.11 & 1, 2.12.03 (6...

  12. PLACES AVAILABLE

    CERN Multimedia

    Monique Duval

    2002-01-01

    Places are available in the following courses: Introduction à DesignSpace :  16.10.02  (1 journée) AutoCAD Mechanical 6 PowerPack (F) :  21, 22, 23.10 et 4, 5, 6.11.02  (6 jours) Introduction à ANSYS 21 - 25.10.02  (5 jours/days) HREF-2002: Helium Refrigeration Techniques (English-French, bilingual) :  21 - 25.10.2002  (7 half days) LabVIEW Basics 1 (English):  21 - 23.10.02  (3 days) LabVIEW Basics 2 (English):  24 & 25.10.02  (2 days) Oracle 8i : Access the Database with Java:  7 & 8.11.02  (2 days) AutoCAD 2002 - niveau 2 :  7 & 8.11.02  (2 jours) AutoCAD 2002 - Level 1:  14, 15, 21, 22.11.02  (4 days) LabVIEW - Advanced (English) :  18 - 20.11.2002  (3 days) AutoCAD 2002 - niveau 1 :  19, 20, 25, 26.11.02 (4 jours) Oracle iDS Designer: First Class:&...

  13. Places available**

    CERN Document Server

    2003-01-01

    Places are available in the following courses: CLEAN-2002 : Travailler en salle blanche (séminaire gratuit) : 4.9.03 (une demi-journée) The CERN EDMS for Local Administrators (free of charge) : 24 & 25.9.03 (2 days) HeREF-2003 : Techniques de la réfrigération Hélium (cours en français avec support en anglais) : 6 - 10.10.2003 (7 demi-journées) The Java Programming Language Level 1 : 6 - 7.10.2003 (2 days) Java 2 Enterprise Edition - Part 2 : Enterprise JavaBeans : 8 - 10.10.2003 (3 days) FileMaker - niveau 1 : 9 & 10.10.03 (2 jours) EXCEL 2000 - niveau 1 : 20 & 22.10.03 (2 jours) AutoCAD 2002 - niveau 1 : 20, 21, 27, 28.10.03 (4 jours) CLEAN-2002 : Working in a Cleanroom (free of charge) : 23.10.03 (half day) AutoCAD Mechanical 6 PowerPack (E) : 23, 24, 30, 31.10 & 12, 13.11.03 (6 days) AutoCAD 2002 - niveau 2 : 10 & 11.11.03 (2 jours)...

  14. Places available**

    CERN Multimedia

    2003-01-01

    Places are available in the following courses: The CERN EDMS for Local Administrators : 24 & 25.9.03 (2 days, free of charge) HeREF-2003 : Techniques de la réfrigération Hélium cours en français avec support en anglais) : 6 - 10.10.2003 (7 demi-journées) The Java Programming Language Level 1 : 6 - 7.10.2003 (2 days) Java 2 Enterprise Edition - Part 2 : Enterprise JavaBeans : 8 - 10.10.2003 (3 days) FileMaker - niveau 1 : 9 & 10.10.03 (2 jours) EXCEL 2000 - niveau 1 : 20 & 22.10.03 (2 jours) AutoCAD 2002 - niveau 1 : 20, 21, 27, 28.10.03 (4 jours) CLEAN-2002 : Working in a Cleanroom : 23.10.03 (half day, free of charge) AutoCAD 2002 - Level 1 : 3, 4, 12, 13.11.03 (4 days) AutoCAD 2002 - niveau 2 : 10 & 11.11.03 (2 jours) ACCESS 2000 - niveau 1 : 13 & 14.11.03 (2 jours) AutoCAD Mechanical 6 PowerPack (E) : 17, 18, 24, 25.11 & 1, 2.12.03 (6 days) FrontPage 2000 - niveau 1 : 20 & 21.11.03 (2 jours) MAGNE-03 : Magnétisme pour l'électrotechnique : 25 - 27.11.03 (3 jours) ...

  15. PLACES AVAILABLE

    CERN Multimedia

    Monique Duval

    2002-01-01

    Places are available in the following courses: LabView hands-on (bilingue/bilingual): 5.11.02 (matin/morning) LabView DAQ hands-on (bilingue/bilingual):  5.11.02  (après-midi afternoon) Introduction au PC et Windows 2000 au CERN:  6 & 7.11.02  (2 jours) Oracle 8i : Access the Database with Java:  7 & 8.11.02  (2 days) AutoCAD 2002 - niveau 2:  7 & 8.11.02  (2 jours) Introduction to PVSS (free of charge):  11.11.2002 pm  (1/2 day) Basic PVSS:  12 - 14.11.02  (3 days) EXCEL 2000 - niveau 1:  12 & 13.11.02  (2 jours) CLEAN-2002: Working in a Cleanroom (English, free of charge):  13.11.2002  (afternoon) LabView Base 1 :  13 - 15.11.02  (3 jours) AutoCAD 2002 - Level 1:  14, 15, 21, 22.11.2002  (4 days) LabVIEW - Advanced:  18 - 20.11.02  (3 days) Auto...

  16. Places available**

    CERN Multimedia

    2003-01-01

    Places are available in the following courses: PIPES-2003 - Pratique du sertissage de tubes métalliques et multicouches :26.8.03(stage pratique) The CERN EDMS for Engineers (free of charge) : 27.8.03 (1 day) CLEAN-2002 : Travailler en salle blanche (séminaire gratuit) : 4.9.03(une demi-journée) The CERN EDMS for Local Administrators (free of charge) : 24 & 25.9.03 (2 days) HeREF-2003 : Techniques de la réfrigération Hélium (cours en français avec support en anglais) : 6 - 10.10.2003 (7 demi-journées) The Java Programming Language Level 1 : 6 - 7.10.2003 (2 days) Java 2 Enterprise Edition - Part 2 : Enterprise JavaBeans : 8 - 10.10.2003 (3 days) FileMaker - niveau 1 : 9 & 10.10.03 (2 jours) EXCEL 2000 - niveau 1 : 20 & 22.10.03 (2 jours) AutoCAD 2002 - niveau 1 : 20, 21, 27, 28.10.03 (4 jours) CLEAN-2002 : Working in a Cleanroom (free of charge) : 23.10.03 (half day) AutoCAD Mechanical 6 PowerPack (E) : 23, 24, 30, 31.10 & 12, 13.11.03 (6 days) AutoCAD 2002 - niveau 2...

  17. Places available**

    CERN Multimedia

    2003-01-01

    Places are available in the following courses: The CERN EDMS for Local Administrators (free of charge) : 24 & 25.9.03 (2 days) HeREF-2003 : Techniques de la réfrigération Hélium (cours en français avec support en anglais) : 6 - 10.10.2003 (7 demi-journées) The Java Programming Language Level 1 : 6 - 7.10.2003 (2 days) Java 2 Enterprise Edition - Part 2 : Enterprise JavaBeans : 8 - 10.10.2003 (3 days) FileMaker - niveau 1 : 9 & 10.10.03 (2 jours) EXCEL 2000 - niveau 1 : 20 & 22.10.03 (2 jours) AutoCAD 2002 - niveau 1 : 20, 21, 27, 28.10.03 (4 jours) CLEAN-2002 : Working in a Cleanroom (free of charge) : 23.10.03 (half day) AutoCAD Mechanical 6 PowerPack (E) : 23, 24, 30, 31.10 & 12, 13.11.03 (6 days) AutoCAD 2002 - niveau 2 : 10 & 11.11.03 (2 jours) ACCESS 2000 - niveau 1 : 13 & 14.11.03 (2 jours) FrontPage 2000 - niveau 1 : 20...

  18. PLACES AVAILABLE

    CERN Multimedia

    Monique Duval

    2002-01-01

    Places are available in the following courses: October 2002   Introduction to the CERN Engineering Data Management System (free of charge):  29.10.2002  (1 day) The CERN EDMS for Advanced users (free of charge):  30.10.2002  (1 day) November 2002   LabView hands-on (bilingue/bilingual): 5.11.02 (matin/morning) LabView DAQ hands-on (bilingue/bilingual):  5.11.02  (après-midi afternoon) Introduction au PC et Windows 2000 au CERN :  6 & 7.11.02  (2 jours) Oracle 8i : Access the Database with Java:  7 & 8.11.02  (2 days) AutoCAD 2002 - niveau 2 :  7 & 8.11.02  (2 jours) Introduction to PVSS (free of charge):  11.11.2002 pm  (1/2 day) Basic PVSS:  12 - 14.11.02  (3 days) EXCEL 2000 - niveau 1 :  12 & 13.11.02  (2 jours) CLEAN-2002: Working in a Cleanroom (English, free ...

  19. PLACES AVAILABLE

    CERN Multimedia

    Monique Duval

    2002-01-01

    Places are available in the following courses: Introduction to Oracle 8i : SQL and PL/SQL:  7 - 11.10.02  (5 days) CLEAN-2002 : Working in a Cleanroom (free of charge):  10.10.02  (half-day, p.m.) LabView Hands-on (bilingue/bilingual) : 10.10.02 (matin/morning) LabView DAQ Hands-on (bilingue/bilingual)  10.10.02 (après-midi /afternoon) Introduction à DesignSpace :  16.10.02  (1 journée) Introduction to DesignSpace:  17.10.02  (1 day) AutoCAD Mechanical 6 PowerPack (F) :  21, 22, 23.10 et 4, 5, 6.11.02  (6 jours) Introduction à ANSYS/Introduction to ANSYS (langue à définir suivant demande/ Language to be chosen according to demand):  21 - 25.10.02  (5 jours/days) HREF-2002: Helium Refrigeration Techniques (English-French, bilingual) :  21 - 25.10.2002  (7 half days) HREF-2002: Techniques de la...

  20. PLACES AVAILABLE

    CERN Multimedia

    Technical Training; Tel 74924

    2002-01-01

    Places are available in the following courses: LabView hands-on : 21.01.02 (1/2 journée) LabView DAQ hands-on : 21.01.02 (1/2 journée) FileMaker Pro : 22 - 25.1.02 (4 jours) MS-Project 2000 : 24 & 25.01.02 (2 jours) Introduction au PC et à Windows 2000 au CERN : 29 - 30.1.02 (2 jours) LabView Base 1 : 4 - 6.2.02 (3 jours) LabView DAQ (E) : 7 & 8.02.02 (2 days) Hands-on Object-Oriented Design & Programming with Java : 11 - 13.02.02 (3 days) C++ for Particle Physicists : 11 - 15.3.2002 (6 * 3 hour lectures) Cours sur la migration AutoCAD : AutoCAD : Mise à jour AutoCAD r-14 vers 2002 (2 jours) AutoCAD Mechanical PowerPack 6 basé sur AutoCAD 2002 (5 jours) If you wish to participate in one of these courses, please discuss with your supervisor and apply electronically directly from the course description pages that can be found on the Web at : Technical Training or fill in an 'application for training' form available from your Divisional Secretariat or from your DTO ...

  1. PLACES AVAILABLE

    CERN Multimedia

    Enseignement Technique; Tél. 74924; Technical Training; Monique Duval; Tel. 74924

    2000-01-01

    Places are available in the following courses : Premiers pas avec votre PC 12 - 15.9.00 (4 demi-journées) WORD 20, 21 et 26, 27.9.2000 (4 jours) JAVA programming level 1 25 - 26.9.2000 (2 days) Gaz inflammables 1 26.9.2000 (1 journée) Advanced aspects of PERL 5 6.10.2000 (1 day) Initiation au WWW 10 - 12.10.00 (3 demi-journées) WORD : importer et manipuler des images 16.10.2000 (1 journée) FileMaker 17, 18 et 24, 25.10.00 (4 jours) Nouveautés de WORD 19 et 20.10.2000 (2 jours) ACCESS 1er niveau 30 - 31.10.00 (2 jours)Introduction à PowerPoint 6.11.00 (1 journée)Nouveautés d’EXCEL 7.11.2000(4 demi-journées)Excel 13, 14 et 20, 21.11.00 (4 jours) LabView hands-on 13.11.2000(4 hours)LabView Basics 1 14 - 16.11.2000 (3 days) MS-Project 1er niveau 14-17.11.00 (4 demi-journées) If you wish to participate in one of these courses, please discuss with your supervisor and apply elec...

  2. PLACES AVAILABLE

    CERN Multimedia

    TECHNICAL TRAINING; Tel. 74460

    2001-01-01

    Places are available in the following courses: MS-Project 1er niveau : 20 - 23.2.01 (4 matins) Architecture d'automatisme : 20 - 21.2.01 (2 jours) Introduction à PowerPoint : 26.2.01 (1 journée) Programmation TSX Premium 1 (Schneider) : 26.2 - 2.3.01 (5 jours) Premiers pas avec votre PC : 27.2 - 2.3.01 (4 matins) C++ for Particle Physicists : 5 - 9.3.01 (6*3 hour lectures) EXCEL : 6, 7 et 13, 14.3.01 (4 jours) The JAVA programming language level 2 :  12 - 14.3.01 (3 days) Nouveautés de FileMaker :  20 - 23.03.01 (4 matins) If you wish to participate in one of these courses, please discuss with your supervisor and apply electronically directly from the course description pages that can be found on the Web at : http://www.cern.ch/Training/ or fill in an 'application for training' form available from your Divisional Secretariat or from your DTO (Divisional Training Officer). Applications will be accepted in the order of their receipt.

  3. PLACES AVAILABLE

    CERN Multimedia

    Technical Training; Tel. 74924

    2002-01-01

    Places are available in the following courses: LabView hands-on : 21.01.02 (1/2 journée) LabView DAQ hands-on : 21.01.02 (1/2 journée) FileMaker Pro : 22 - 25.1.02 (4 jours) MS-Project 2000 : 22, 24 & 25.01.02 (3 jours) Introduction au PC et à Windows 2000 au CERN : 29 - 30.1.02 (2 jours) LabView Base 1 : 4 - 6.2.02 (3 jours) LabView DAQ  (E) :  7 & 8.02.02 (2 days) Hands-on Object-Oriented Design & Programming with Java :  11 - 13.02.02 (3 days) PVSS basics :  11 - 15.2.02 (5 days) Introduction à Windows 2000 : 18.2.02 (1 demi-journée) Introduction to the CERN Engineering Data Management System :  20.2.02 (1 day) The CERN Engineering Data Management System for Advanced users :  21.2.02  (1 day) C++ for Particle Physicists :  11 - 15.3.2002  (6 * 3 hour lectures) Cours sur la migration AutoCAD : AutoCAD : Mise à...

  4. PLACES AVAILABLE

    CERN Multimedia

    Technical Training; Tel. 74924

    2001-01-01

    Places are available in the following courses: LabVIEW - Basics 1 :  10 - 12.12.01 (3 days) Introduction to XML :  12 & 13.12.01 (2 days) Introduction au PC et Windows 2000 : 12 & 14.12.01 (2 jours) LabVIEW - Basics 2 :  13 - 14.12.01 (2 days) Habilitation électrique : superviseurs : 17.12.2001 (1/2 journée) MS-Project 2000 : 10 & 11.01.02 (2 jours) EXCEL 2000 - niveau 2 : 15 - 16.1.02 (2 jours) Sécurité dans les installations cryogéniques: 15-17.1.2002 (2 demi-journées) C++ Programming Level 2 - Traps and Pitfalls :  15 - 18.1.2002  (4 days) ELEC-2002 Winter Term: Readout and system electronics for Physics  15.1.2002 - 7.2.2002 (8 half- days) Nouveautés de WORD 2000 : 18.1.02 (1/2 journée) LabView hands-on : 21.01.02 (1/2 journée) LabView DAQ hands-on : 21.01.02 (1/2 journée) FileMaker Pro : 22 -...

  5. PLACES AVAILABLE

    CERN Multimedia

    Enseignement Technique; Tel. 74924

    2001-01-01

    Places are available in the following courses: MS-Project 2000 : 10 & 11.01.02 (2 jours) EXCEL 2000 - niveau 2 : 15 - 16.1.02 (2 jours) Sécurité dans les installations cryogéniques: 15-17.1.2002 (2 demi-journées) C++ Programming Level 2 - Traps and Pitfalls :  15 - 18.1.2002  (4 days) ELEC-2002 Winter Term: Readout and system electronics for Physics  15.1.2002 - 7.2.2002 (8 half- days) Nouveautés de WORD 2000 : 18.1.02 (1/2 journée) LabView hands-on : 21.01.02 (1/2 journée) LabView DAQ hands-on : 21.01.02 (1/2 journée) FileMaker Pro : 22 - 25.1.02 (4 jours) MS-Project 2000 : 24 & 25.01.02 (2 jours) Introduction au PC et à Windows 2000 au CERN : 29 - 30.1.02 (2 jours) LabView Base 1 : 4 - 6.2.02 (3 jours) LabView DAQ  (E) :  7 & 8.02.02 (2 days) Hands-on Object-Oriented Design & Programming with Java :&nbs...

  6. Places available**

    CERN Multimedia

    2003-01-01

    Places are available in the following courses : CLEAN-2002 : Working in a cleanroom (free course, registration required) : 2.4.03 (half-day, afternoon) LabView base 1/LabView Basics 1 (Langue à définir/ language to be decided) : 9 - 11.4.03 (3 jours/3 days) DISP-2003 - Spring II Term : Advanced Digital Signal Processing : 30.4, 7, 14, 21.5.03 (4 X 2-hour lectures) AutoCAD 2002 - niveau 1 : 29, 30.4 et 7, 8.5.03 (4 jours) AutoCAD 2002 - niveau 2 : 5 & 6.5.03 (2 jours) AutoCAD Mechanical 6 PowerPack (F) : 12, 13, 20, 21, 27 & 28.5.03(6 jours) Formation Siemens SIMATIC /Siemens SIMATIC Training : Introduction à STEP7 /Introduction to STEP7 : 3 & 4.6.03 (2 jours/2 days) Programmation STEP7/STEP7 Programming : 31.3 - 4.4.03 / 16 - 20.6.03 (5 jours/5 days) Réseau Simatic Net /Simatic Net Network : 15 & 16.4.03 / 26 & 27.6.03 These courses will be given in French or English following the requests. Cours de sécurité : Etre TSO au CERN : 3 sessions sont programmées pour 2003 : 25...

  7. Places available **

    CERN Multimedia

    2003-01-01

    Places are available in the following courses : CLEAN-2002 : Working in a cleanroom (free course, registration required): 11.4.03 (half-day, afternoon, ) LabView Basics 2 : 10 - 11.4.03 (3 days) DISP-2003 - Spring II Term : Advanced Digital Signal Processing : 30.4, 7, 14, 21.5.03 (4 X 2-hour lectures) AutoCAD 2002 - niveau 1 : 29, 30.4 et 7, 8.5.03 (4 jours) Oracle iDS Reports : Build Internet Reports : 5 - 9.5.03 (5 days) AutoCAD 2002 - niveau 2 : 5 & 6.5.03 (2 jours) AutoCAD Mechanical 6 PowerPack (F) : 12, 13, 20, 21, 27 & 28.5.03 (6 jours) Formation Siemens SIMATIC /Siemens SIMATIC Training : Introduction à STEP7 /Introduction to STEP7 : 3 & 4.6.03 (2 jours/2 days) Programmation STEP7/STEP7 Programming : 31.3 - 4.4.03 / 16 - 20.6.03 (5 jours/5 days) Réseau Simatic Net /Simatic Net Network : 15 & 16.4.03 / 26 & 27.6.03 These courses will be given in French or English following the requests. Cours de sécurité : Etre TSO au CERN : Prochaines sessions : 24, 25 & 27.6....

  8. Places available**

    CERN Multimedia

    2003-01-01

    Places are available in the following courses : DISP-2003 - Spring II Term : Advanced Digital Signal Processing : 30.4, 7, 14, 21.5.03 (4 X 2-hour lectures) Oracle iDS Reports : Build Internet Reports : 5 - 9.5.03 (5 days) LabView DAQ (language to be defined) : 8 & 9.5.03 AutoCAD Mechanical 6 PowerPack (F) : 12, 13, 20, 21, 27 & 28.5.03 (6 jours) AutoCAD 2002 - niveau 2 : 3 & 4.6.03 (2 jours) LabView DSC (language to be defined) : 19 & 20.6.03 Siemens SIMATIC Training : Introduction to STEP7 : 3 & 4.6.03 (2 days) STEP7 Programming : 16 - 20.6.03 (5 days) Simatic Net Network : 15 & 16.4.03 / 26 & 27.6.03 (sessions of 2 days) These courses will be given in French or English following the requests. Cours de sécurité : Etre TSO au CERN : Prochaines sessions : 24, 25 & 27.6.03 - 4, 5 & 7.11.03 (session de 3 jours) If you wish to participate in one of these courses, please discuss with your supervisor and apply electronically directly from the course description ...

  9. PLACES AVAILABLE

    CERN Multimedia

    Monique Duval

    2002-01-01

    Places are available in the following courses: Habilitation électrique : recyclage HT/BT : 11 - 15.3.2002  (2 * 2 heures) PVSS Basics :  8 - 12.4.02  (5 days) ELEC-2002 : Spring Term :  9, 11, 16, 18, 23, 25, 30.4.02 (7 * 2.5 hours) LabVIEW base 1 : 22 - 24.4.02 (3 jours) LabVIEW DSC (F) 25 & 26.4.02 (2 jours) LabVIEW Basics 2 : 13 & 14.5.02 (2 days) LabVIEW DAQ (F) : 15 & 16.5.02 (2 jours) Cours sur la migration AutoCAD :   AutoCAD : Mise à jour AutoCAD r-14 vers 2002 (2 jours) AutoCAD Mechanical PowerPack 6 basé sur AutoCAD 2002 (5 jours) If you wish to participate in one of these courses, please discuss with your supervisor and apply electronically directly from the course description pages that can be found on the Web at : Technical Training or fill in an 'application for training' form available from your Divisional Secretariat or from your DTO (Divisional Training Officer). Applica...

  10. Places available**

    CERN Multimedia

    2003-01-01

    Places are available in the following courses : CLEAN-2002 : Working in a cleanroom (free course, registration required): 11.4.03 (half-day, afternoon, ) LabView Basics 2 : 10 - 11.4.03 (3 days) DISP-2003 - Spring II Term : Advanced Digital Signal Processing : 30.4, 7, 14, 21.5.03 (4 X 2-hour lectures) AutoCAD 2002 - niveau 1 : 29, 30.4 et 7, 8.5.03 (4 jours) Oracle iDS Reports : Build Internet Reports : 5 - 9.5.03 (5 days) AutoCAD 2002 - niveau 2 : 5 & 6.5.03 (2 jours) AutoCAD Mechanical 6 PowerPack (F) : 12, 13, 20, 21, 27 & 28.5.03(6 jours) Formation Siemens SIMATIC /Siemens SIMATIC Training : Introduction à STEP7 /Introduction to STEP7 : 3 & 4.6.03 (2 jours/2 days) Programmation STEP7/STEP7 Programming : 31.3 - 4.4.03 / 16 - 20.6.03 (5 jours/5 days) Réseau Simatic Net /Simatic Net Network : 15 & 16.4.03 / 26 & 27.6.03 These courses will be given in French or English following the requests. Cours de sécurité : Etre TSO au CERN : Prochaines sessions : 24, 25 & 27.6...

  11. Places available**

    CERN Multimedia

    2003-01-01

    Places are available in the following courses : DISP-2003 - Spring II Term : Advanced Digital Signal Processing : 30.4, 7, 14, 21.5.03 (4 X 2-hour lectures) Programmation de pilotes périphériques : 5 - 8.5.03 (4 jours) Oracle iDS Reports : Build Internet Reports : 5 - 9.5.03 (5 days) LabView DAQ (language to be defined) : 8 & 9.5.03 AutoCAD Mechanical 6 PowerPack (F) : 12, 13, 20, 21, 27 & 28.5.0 (6 jours) FrontPage 2000 - niveau 1 : 20 & 21.5.03 (2 jours) AutoCAD 2002 - niveau 2 : 3 & 4.6.03 (2 jours) EXCEL 2000 - niveau 1 : 10 & 11.6.03 (2 jours) EXCEL 2000 - level 1 : 12 & 13.6.03 (2 days) PowerPoint 2000 (F) : 17 & 18.6.03 (2 jours) FrontPage 2000 - niveau 2 : 19 & 20.6.03 (2 jours) LabView DSC (langue à décider/language to be defined) : 19 & 20.6.03 EXCEL 2000 - niveau 2 : 24 & 25.6.03 (2 jours) Siemens SIMATIC Training : Introduction to STEP7 : 3 & 4.6.03 (2 days) STEP7 Programming : 16 - 20.6.03 (5 days) Simatic Net Network : 26 & 27.6.03 ...

  12. Places available**

    CERN Multimedia

    2003-01-01

    Places are available in the following courses : CLEAN-2002 : Working in a cleanroom (free course, registration required): 11.4.03 (half-day, afternoon) LabView Basics 2 : 10 - 11.4.03 (3 days) DISP-2003 - Spring II Term : Advanced Digital Signal Processing : 30.4, 7, 14, 21.5.03 (4 X 2-hour lectures) AutoCAD 2002 - niveau 1 : 29, 30.4 et 7, 8.5.03 (4 jours) Oracle iDS Reports : Build Internet Reports : 5 - 9.5.03 (5 days) AutoCAD 2002 - niveau 2 : 5 & 6.5.03 (2 jours) AutoCAD Mechanical 6 PowerPack (F) : 12, 13, 20, 21, 27 & 28.5.03(6 jours) Formation Siemens SIMATIC /Siemens SIMATIC Training : Introduction à STEP7 /Introduction to STEP7 : 3 & 4.6.03 (2 jours/2 days) Programmation STEP7/STEP7 Programming : 16 - 20.6.03 (5 jours/5 days) Réseau Simatic Net /Simatic Net Network : 15 & 16.4.03 / 26 & 27.6.03 These courses will be given in French or English following the requests. Cours de sécurité : Etre TSO au CERN : Prochaines sessions : 24, 25 & 27.6.03 - 4, 5 & 7....

  13. Places available**

    CERN Multimedia

    2003-01-01

    Places are available in the following courses : Introduction to PVSS : 10.3.03 (half-day, afternoon) CLEAN-2002 : Working in a cleanroom : 2.4.03 (half-day, afternoon, free course, registration required) LabView Basics 1 : 9 - 11.4.03 (3 days) Language to be decided. DISP-2003 - Spring II Term : Advanced Digital Signal Processing : 30.4, 7, 14, 21.5.03 (4 X 2-hour lectures). AutoCAD 2002 - niveau 1 : 29, 30.4 et 7, 8.5.03 (4 jours) AutoCAD 2002 - niveau 2 : 5 & 6.5.03 (2 jours) AutoCAD Mechanical 6 PowerPack (F) : 12, 13, 20, 21, 27 & 28.5.03 (6 jours) Siemens SIMATIC Training: Introduction to STEP7 : 3 & 4.6.03 (2 days) STEP7 Programming : 31.3 - 4.4.03 / 16 - 20.6.03 (5 days) Simatic Net Network : 15 & 16.4.03 / 26 & 27.6.03 These courses will be given in French or English following the requests. Cours de sécurité: Etre TSO au CERN : 3 sessions sont programmées pour 2003 : 25, 26 & 28.3.03 - 24, 25 & 27.6.03 - 4, 5 & 7.11.03 (sessions de 3 jours) ** The number o...

  14. PLACES AVAILABLE

    CERN Multimedia

    Monique Duval

    2002-01-01

    Places are available in the following courses: November 2002   Hands-on Object-Oriented Design and Programming with C++:  19 - 21.11.02  (3 days)  December 2002   LabVIEW - DSC (English) :  2 - 3.12.02  (2 days) AutoCAD 2002 - niveau 2 :  2 & 3.12.02  (2 jours) FileMaker (Français) :  2 - 5.12.02  (4 jours) PCAD Schémas - Débutants :  5 & 6.12.02  (2 jours) PCAD PCB - Débutants :  9 - 11.12.02  (3 jours) FrontPage 2000 - level 1:  9 & 10.12.02  (2 days) If you wish to participate in one of these courses, please discuss with your supervisor and apply electronically directly from the course description pages that can be found on the Web at : Technical Training or fill in an 'application for training' form available from your Divisional Secretariat or from your DTO (Divisiona...

  15. PLACES AVAILABLE

    CERN Multimedia

    Monique Duval

    2002-01-01

    Places are available in the following courses: November 2002   Java Programming Language level 1 :  28 & 29.11.02  (2 days) December 2002   LabVIEW - DSC (English) :  2 - 3.12.02  (2 days) FileMaker (Français) :  2 - 5.12.02  (4 jours) PCAD Schémas - Débutants :  5 & 6.12.02  (2 jours) PCAD PCB - Débutants :  9 - 11.12.02  (3 jours) FrontPage 2000 - level 1:  9 & 10.12.02  (2 days) If you wish to participate in one of these courses, please discuss with your supervisor and apply electronically directly from the course description pages that can be found on the Web at : Technical Training or fill in an 'application for training' form available from your Divisional Secretariat or from your DTO (Divisional Training Officer). Applications will be accepted in the order of their receipt. Technical Training M...

  16. PLACES AVAILABLE

    CERN Multimedia

    Monique Duval

    2002-01-01

    Places are available in the following courses: November 2002   Introduction to PVSS (free of charge): 11.11.02  (afternoon) EXCEL 2000 - niveau 1 :  12 & 13.11.02  (2 jours) CLEAN-2002: Working in a Cleanroom (English, free of charge):  13.11.2002  (afternoon) AutoCAD 2002 - niveau 1 :  14, 15, 21, 22.11.02  (4 jours) Hands-on Object-Oriented Design and Programming with C++:  19 - 21.11.02  (3 days)  EXCEL 2000 - niveau 2 :  25 & 26.11.02  (2 jours) FrontPage 2000 - niveau 1 :  27 & 28.11.02  (2 jours) December 2002   LabVIEW - DSC (English) :  2 - 3.12.02  (2 days) AutoCAD 2002 - niveau 2 :  2 & 3.12.02  (2 jours) FileMaker (Français) :  2 - 5.12.02  (4 jours) PCAD Schémas - Débutants :  5 & 6.12.02 ...

  17. PLACES AVAILABLE

    CERN Multimedia

    Technical training; Tel. 74924

    2001-01-01

    Places are available in the following courses: PROFIBUS : 25 - 26.9.01 (2 jours) PROFIBUS : 27 - 28.9.01 (2 days) Automates et réseaux de terrain : 3 - 4.10.2001 (2 jours) PCAD Schémas - débutants : 4 - 5.10.01 (2 jours) PCAD PCB - débutants : 8 - 10.10.01 (3 jours) Programmation TSX Premium 1 : 15 - 19.10.01 (5 jours) Programmation TSX Premium 1 : 22 - 26.10.01 (5 jours) Programming TSX Premium 2: 19 - 23.11.01 (5 days) Programmation TSX Premium 2 : 26 - 30.11.01 (5 jours) Autocad Migration support courses: a detailed calendar will be published shortly for this series of sessions which will start on 15.10.2001. Registration is already open AutoCAD : Mise à jour AutoCAD r-14 vers 2002 (2 jours) AutoCAD Mechanical PowerPack 6 basé sur AutoCAD 2002 (5 jours) The following LabView courses will be given in either English or French according to demand LabVIEW - Base 1 / LabVIEW - Basics 1 : 10 - 12.9.01 (3 jours / 3 days)...

  18. PLACES AVAILABLES

    CERN Multimedia

    Technical Training; Tel. 74924

    2001-01-01

    Places are available in the following courses: PVSS Basics : 20 - 24.8.01 (5 days) PROFIBUS : 25 - 26.9.01 (2 jours) PROFIBUS : 27 - 28.9.01 (2 days) PCAD Schémas - débutants : 4 - 5.10.01 (2 jours) PCAD PCB - débutants : 8 - 10.10.01 (3 jours) Programming TSX Premium 1: 15 - 19.10.01 (5 days) Programmation TSX Premium 1 : 22 - 26.10.01 (5 jours) Programming TSX Premium 2: 19 - 23.11.01 (5 days) Programmation TSX Premium 2 : 26 - 30.11.01 (5 jours) The following LabView courses will be given in either English or French according to demand LabVIEW - Base 1 / LabVIEW - Basics 1 : 10 - 12.9.01 (3 jours / 3 days) LabVIEW - DAQ / LabVIEW - DAQ : 13 - 14.9.01 (2 jours / 2 days) LabVIEW - Base 1 / LabVIEW - Basics 1 : 15 - 17.10.01 (3 jours / 3 days) LabVIEW - Base 2 / LabVIEW - Basics 2 : 18 - 19.10.01 (2 jours / 2 days) LabVIEW - Base 1 / LabVIEW - Basics 1 : 12 - 14.11.01 (3 jours / 3 days) LabVIEW - DAQ / LabVIEW - DAQ : 15 - 16.11.01 (2 jours / 2...

  19. PLACES AVAILABLE

    CERN Multimedia

    Monique Duval

    2002-01-01

    Places are available in the following courses: November 2002   LabView hands-on (bilingue/bilingual): 5.11.02 (matin/morning) LabView DAQ hands-on (bilingue/bilingual):  5.11.02  (après-midi afternoon) PCAD Schémas - Débutants :  5 & 6.11.02  (2 jours) PCAD PCB - Débutants :  9 - 11.11.02  (3 jours) Introduction au PC et Windows 2000 au CERN :  6 & 7.11.02  (2 jours) Oracle 8i : Access the Database with Java :  7 & 8.11.02  (2 days) Introduction to PVSS (free of charge):  11.11.2002 pm  (1/2 day) Basic PVSS:  12 - 14.11.02  (3 days) EXCEL 2000 - niveau 1 :  12 & 13.11.02  (2 jours) CLEAN-2002: Working in a Cleanroom (English, free of charge):  13.11.2002  (afternoon) LabView Base 1 :  13 - 15.11.02  (3 jours) AutoCAD 2002 - niveau 1 :  14, 15, 21, 22.11.02  (4 jours) LabVIEW - Advanced:  18 - 20.11.02  (3 days) Hands-on Object-Oriented Design and Programming with C++ :  19 - 21.11.02  (3 days)  LabVIEW - Basics 2:  21 - 22.11.02 ...

  20. Places available**

    CERN Multimedia

    2003-01-01

    Places are available in the following courses : EXCEL 2000 - niveau 1 : 10 & 11.6.03 (2 jours) Conception de PCB rapides dans le flot Cadence : 11.6.03 (matin) EXCEL 2000 - level 1 : 12 & 13.6.03 (2 days) Introduction to PVSS : 16.6.03 (p.m.) Basic PVSS : 17 - 19.6.03 (3 days) Réalisation de PCB rapides dans le flot Cadence : 17.6.03 (matin) PVSS - JCOP Framework Tutorial : 20.6.03 (1 day) EXCEL 2000 - niveau 2 : 24 & 25.6.03 (2 jours) Siemens SIMATIC Training : Introduction to STEP7 : 3 & 4.6.03 (2 jours/2 days) STEP7 Programming : 16 - 20.6.03 (5 jours/5 days) Simatic Net Network : 26 & 27.6.03 (2 jours/2 days) These courses will be given in French or English following the requests. Programmation automate Schneider : Programmation automate Schneider TSX Premium - 1er niveau : 10 - 13.6.03 (4 jours) - audience : toute personne qui veux maitriser la msie en uvre et la programmation d'un automate TSX Premium - objectifs : maitriser la mise en uvre et la programmation d'un autom...

  1. Places available**

    CERN Multimedia

    2003-01-01

    Places are available in the following courses : FrontPage 2000 - niveau 1 : 20 & 21.5.03 (2 jours) PIPES-2003 : Pratique du sertissage de tubes métalliques et multicouches : 21.5.03 (1 jour) Introduction à la CAO Cadence : de la saisie de schéma Concept-HDL au PCB : 20 & 22.5.03 (2 jours) AutoCAD 2002 - niveau 2 : 3 & 4.6.03 (2 jours) AutoCAD Mechanical 6 PowerPack (F) : 5, 6, 12, 13, 26, 27.6.03 (6 jours) EXCEL 2000 - niveau 1 : 10 & 11.6.03 (2 jours) Conception de PCB rapides dans le flot Cadence : 11.6.03 (matin) EXCEL 2000 - level 1 : 12 & 13.6.03 (2 days) PowerPoint 2000 (F) : 17 & 18.6.03 (2 jours) Réalisation de PCB rapides dans le flot Cadence : 17.6.03 (matin) FrontPage 2000 - niveau 2 : 19 & 20.6.03 (2 jours) LabView DSC (langue à décider/language to be defined) : 19 & 20.6.03 EXCEL 2000 - niveau 2 : 24 & 25.6.03 (2 jours) Siemens SIMATIC Training: Introduction to STEP7 : 3 & 4.6.03 (2 days) STEP7 Programming : 16 - 20.6.03 (5 days) Simatic...

  2. PLACES AVAILABLE

    CERN Multimedia

    Technical Training; Tel. 74924

    2001-01-01

    Places are available in the following courses: PVSS Basics : 20 - 24.8.01 (5 days) PROFIBUS : 25 - 26.9.01 (2 jours) PROFIBUS : 27 - 28.9.01 (2 days) PCAD Schémas - débutants : 4 - 5.10.01 (2 jours) PCAD PCB - débutants : 8 - 10.10.01 (3 jours) Programming TSX Premium 1: 15 - 19.10.01 (5 days) Programmation TSX Premium 1 : 22 - 26.10.01 (5 jours) Programming TSX Premium 2: 19 - 23.11.01 (5 days) Programmation TSX Premium 2 : 26 - 30.11.01 (5 jours) The following LabView courses will be given in either English or French according to demand LabVIEW - Base 1 / LabVIEW - Basics 1 : 10 - 12.9.01 (3 jours / 3 days) LabVIEW - DAQ / LabVIEW - DAQ : 13 - 14.9.01 (2 jours / 2 days) LabVIEW - Base 1 / LabVIEW - Basics 1 : 15 - 17.10.01 (3 jours / 3 days) LabVIEW - Base 2 / LabVIEW - Basics 2 : 18 - 19.10.01 (2 jours / 2 days) LabVIEW - Base 1 / LabVIEW - Basics 1 : 12 - 14.11.01 (3 jours / 3 days) LabVIEW - DAQ / LabVIEW - DAQ : 15 - 16.11.01 (2 jours / 2...

  3. PLACES AVAILABLE

    CERN Multimedia

    Technical Training; Tel. 74924

    2001-01-01

    Places are available in the following courses: Introduction à Windows 2000 au CERN : 2 sessions de _ journée les 24 et 25.9.01 PROFIBUS : 25 - 26.9.01 (2 jours) PROFIBUS : 27 - 28.9.01 (2 days) PowerPoint 2000 : 1 et 2.10.01 (2 jours) EXCEL 2000 - niveau 1 : 3 et 4.10.01 (2 jours) Automates et réseaux de terrain : 3 - 4.10.2001 (2 jours) PCAD Schémas - débutants : 4 - 5.10.01 (2 jours) Introduction à Outlook : 5.10.01 (1 journée) Frontpage 2000 - niveau 1 : 8 et 9.10.01 (2 jours) PCAD PCB - débutants : 8 - 10.10.01 (3 jours) C++ for Particle Physicists : 8 - 12.10.01 (6 3-hour lectures) MS-Project 2000 - niveau 1 : 15 - 18.10.01 (4 demi-journées) LabView Basics 1 :  15 - 17.10.01  (3 days) Programmation TSX Premium 1 : 15 - 19.10.01 (5 jours) WORD 2000 : importer et manipuler des images : 19.10.01 (1 journée) Programmation TSX Premium 1 : 22 - 26.10.01...

  4. PLACES AVAILABLE

    CERN Multimedia

    Technical Training; Tel. 74924

    2001-01-01

    Places are available in the following courses: Cadence Board Design tools : Upgrading to release 14 :  3 1-day sessions on 9, 10 & 11.10.01 MS-Project 2000 - niveau 1 : 15 - 18.10.01 (4 demi-journées) LabView Base 2 : 18 & 19.10.01 (2 jours) WORD 2000 : importer et manipuler des images : 19.10.01 (1 journée) Contract Follow-up (F) :  30.10.01 (1/2 journée) The CERN Engineering Data Management System for Electronics Design :  30.10.01 (1 day) UNIX pour non-programmeurs : 5 - 7.11.01 (3 jours) The Java programming language Level 1: 8 - 9.11.01 (2 days) LabView Base 1 : 12 - 14.11.01 (3 jours) Introduction to PERL 5 :  15 - 16.11.01  (2 days) Introduction to XML :  19 - 20.11.01 (2 days) Programming TSX Premium 1 :  19 - 23.11.01  (5 days) Introduction to C Programming :  21- 23.11.01 (3 days) The Java programming language Level 2:  26 - 28.11.01 (...

  5. PLACES AVAILABLE

    CERN Multimedia

    Technical Training; Tel. 74924

    2001-01-01

    Places are available in the following courses: Introduction à Windows 2000 au CERN : 2 sessions de _ journée les 24 et 25.9.01 PROFIBUS : 25 - 26.9.01 (2 jours) PROFIBUS : 27 - 28.9.01 (2 days) EXCEL 2000 - niveau 1 : 3 et 4.10.01 (2 jours) Automates et réseaux de terrain : 3 - 4.10.2001 (2 jours) Introduction à Outlook : 5.10.01 (1 journée) Frontpage 2000 - niveau 1 : 8 et 9.10.01 (2 jours) C++ for Particle Physicists : 8 - 12.10.01 (6 lectures) MS-Project 2000 - niveau 1 : 15 - 18.10.01 (4 demi-journées) Programmation TSX Premium 1 : 15 - 19.10.01 (5 jours) WORD 2000 : importer et manipuler des images : 19.10.01 (1 journée) Programmation TSX Premium 1 : 22 - 26.10.01 (5 jours) UNIX pour non-programmeurs : 5 - 7.11.01 (3 jours) The Java programming language Level 1: 8 - 9.11.01 (2 days) Introduction to PERL 5 :  15 - 16.11.01  (2 days) Introduction to XML :  19 - 20.11.01 (2...

  6. PLACES AVAILABLE

    CERN Multimedia

    Technical Training; Tel. 74924

    2001-01-01

    Places are available in the following courses: EXCEL 2000 - niveau 1 : 3 et 4.10.01 (2 jours) Automates et réseaux de terrain : 3 - 4.10.2001 (2 jours) Introduction à Outlook : 5.10.01 (1 journée) C++ for Particle Physicists : 8 - 12.10.01 (6 lectures) Cadence Board Design tools : Upgrading to release 14 : 3 1-day sessions on 9, 10 & 11.10.01 MS-Project 2000 - niveau 1 : 15 - 18.10.01 (4 demi-journées) LabView Base 2 : 18 & 19.10.01 (2 jours) WORD 2000 : importer et manipuler des images : 19.10.01 (1 journée) The CERN Engineering Data Management System for Electronics Design :  30.10.01 (1 day) UNIX pour non-programmeurs : 5 - 7.11.01 (3 jours) The Java programming language Level 1: 8 - 9.11.01 (2 days) Introduction to PERL 5 :  15 - 16.11.01  (2 days) Introduction to XML :  19 - 20.11.01 (2 days) Programming TSX Premium 1 :  19 - 23.11.01  (5 days) Introd...

  7. PLACES AVAILABLE

    CERN Multimedia

    Technical Training; Tel. 74924

    2001-01-01

    Places are available in the following courses: MS-Project 2000 - niveau 1 : 15 - 18.10.01 (4 demi-journées) LabView Base 2 : 18 & 19.10.01 (2 jours) WORD 2000 : importer et manipuler des images : 19.10.01 (1 journée) Contract Follow-up (F) : 30.10.01 (1/2 journée) The CERN Engineering Data Management System for Electronics Design :  30.10.01 (1 day) UNIX pour non-programmeurs : 5 - 7.11.01 (3 jours) The Java programming language Level 1: 8 - 9.11.01 (2 days) LabView Base 1 : 12 - 14.11.01 (3 jours) Automates et réseaux de terrain : 13 & 14.11.01 (2 jours) Introduction to PERL 5 :  15 - 16.11.01  (2 days) Introduction to XML :  19 - 20.11.01 (2 days) Programming TSX Premium 1 :  19 - 23.11.01  (5 days) Introduction to C Programming :  21- 23.11.01 (3 days) The Java programming language Level 2:  26 - 28.11.01 (3 days) Programmation TSX Premium 2 : 26 ...

  8. PLACES AVAILABLE

    CERN Multimedia

    Monique Duval

    2002-01-01

    Places are available in the following courses: LabView Base 1 :  23 - 25.9.02  (3 jours) Object-Oriented Analysis & Design using UML:  25 - 27.9.02  (3 days) LabView DAQ (E):  26 - 27.9.02  (2 days) Introduction to Oracle 8i : SQL and PL/SQL:  7 - 11.10.02  (5 days) CLEAN-2002 : Working in a Cleanroom (free of charge):  10.10.02  (half-day, p.m.) AutoCAD 2002 - niveau 2 :  14 - 15.10.02  (2 jours) Introduction à DesignSpace :  16.10.02  (1 journée) Introduction to DesignSpace:  17.10.02  (1 day) AutoCAD 2002 - Level 1:  17, 18, 24, 25.10.02  (4 days) AutoCAD Mechanical 6 PowerPack (F) :  21, 22, 23.10 et 4, 5, 6.11.02  (6 jours) Introduction à ANSYS/Introduction to ANSYS (langue à définir suivant demande/ Language to be chosen according to demand):...

  9. PLACES AVAILABLE

    CERN Multimedia

    Monique Duval

    2002-01-01

    Places are available in the following courses: Java 2 Enterprise Edition - Part 2: Enterprise JavaBeans:  18 - 20.9.02  (3 days) AutoCAD 2002 - niveau 1 :  19, 20, 26, 27.9.02  (4 jours) LabView Base 1 :  23 - 25.9.02  (3 jours) Object-Oriented Analysis & Design using UML:  25 - 27.9.02  (3 days) LabView DAQ (E):  26 - 27.9.02  (2 days) Introduction to Oracle 8i : SQL and PL/SQL:  7 - 11.10.02  (5 days) CLEAN-2002 : Working in a Cleanroom (free of charge):  10.10.02  (half-day, p.m.) AutoCAD 2002 - niveau 2 :  14 - 15.10.02  (2 jours) Introduction à DesignSpace :  16.10.02  (1 journée) Introduction to DesignSpace:  17.10.02  (1 day) AutoCAD 2002 - Level 1:  17, 18, 24, 25.10.02  (4 days) AutoCAD Mechanical 6 PowerPack (F) :  21, 22, 23.10 et 4, 5, 6.11....

  10. PLACES AVAILABLE

    CERN Multimedia

    Technical Training; Tel. 74924

    2001-01-01

    Places are available in the following courses: Automates et réseaux de terrain : 13 & 14.11.01 (3 jours) Introduction à Windows 2000 au CERN : 12 - 14.11.01 (1/2 journée) Introduction to Windows 2000 at CERN :  14.11.01  (half-day) Introduction to PERL 5 :  15 - 16.11.01  (2 days) Sécurité dans les installations cryogéniques : 21 - 22.11.2001 (2 demi-journées) Introduction to C Programming :  21- 23.11.01 (3 days) Programmation TSX Premium 2 : 26 - 30.11.01 (5 jours) Contract Follow-up (F) : 26.11.01 (1/2 journée) Object-Oriented Analysis and Design :  27 - 30.11.2001  (4 days) Introduction to the CERN Engineering Data Management System :  30.11.2001 (1 day) Electromagnetic Compatibility (EMC): Introduction (bilingual) :  3.12.01 (half-day) Introduction to the CERN Engineering Data Management System : 07.12.2001...

  11. PLACES AVAILABLE

    CERN Multimedia

    Technical Training; Tel. 74924

    2001-01-01

    Places are available in the following courses: Contract Follow-up (F) : 30.10.01 (1/2 journée) The CERN Engineering Data Management System for Electronics Design :  30.10.01 (1 day) UNIX pour non-programmeurs : 5 - 7.11.01 (3 jours) Nouveautés d'EXCEL : 5.11.01 (1/2 journée) Introduction a Windows 2000 au CERN : 6.11.01 (1/2 journée) The Java programming language Level 1: 8 - 9.11.01 (2 days) LabView Base 1 : 12 - 14.11.01 (3 jours) Automates et réseaux de terrain : 13 & 14.11.01 (2 jours) Introduction to PERL 5 :  15 - 16.11.01  (2 days) Introduction to XML :  19 - 20.11.01 (2 days) Programming TSX Premium 1 :  19 - 23.11.01  (5 days) Introduction to C Programming :  21- 23.11.01 (3 days) The Java programming language Level 2:  26 - 28.11.01 (3 days) Programmation TSX Premium 2 : 26 - 30.11.01 (5 jours) Autocad Migration support courses: a detail...

  12. PLACES AVAILABLE

    CERN Multimedia

    Technical Training; Tel. 74924

    2001-01-01

    Places are available in the following courses: Contract Follow-up (F) : 30.10.01 (1/2 journée) The CERN Engineering Data Management System for Electronics Design :  30.10.01 (1 day) Nouveautés d'Excel 2000 : 5.11.01 (1/2 journée) UNIX pour non-programmeurs : 5 - 7.11.01 (3 jours) Introduction à Windows 2000 au CERN : 6.11.01 (1/2 journée) The Java programming language Level 1: 8 - 9.11.01 (2 days) LabView Base 1 : 12 - 14.11.01 (3 jours) LabVIEW DAQ (F) : 15 & 16.11.01 (2 jours) Automates et réseaux de terrain : 13 & 14.11.01 (2 jours) Introduction to PERL 5 :  15 - 16.11.01  (2 days) LabVIEW - DAQ : 15 - 16.11.01 (2 jours) Introduction to XML :  19 - 20.11.01 (2 days) Introduction to C Programming :  21- 23.11.01 (3 days) Programmation TSX Premium 2 : 26 - 30.11.01 (5 jours) Object-Oriented Analysis and Design :  27 - 30.11.2001 (4 days) Hands...

  13. PLACES AVAILABLE

    CERN Multimedia

    Technical Training; Tel. 74924

    2001-01-01

    Places are available in the following courses: Nouveautés d'EXCEL : 5.11.01 (1/2 journée) Introduction a Windows 2000 au CERN : 6.11.01 (1/2 journée) UNIX pour non-programmeurs : 5 - 7.11.01 (3 jours) Design Patterns :  7 - 8.11.01 (2 days) The Java programming language Level 1: 8 - 9.11.01 (2 days) Automates et réseaux de terrain : 13 & 14.11.01 (3 jours) Introduction à Windows 2000 au CERN : 12 - 14.11.01 (1/2 journée) Introduction to Windows 2000 at CERN :  14.11.01  (half-day) Introduction to PERL 5 :  15 - 16.11.01  (2 days) Introduction to C Programming :  21- 23.11.01 (3 days) Programmation TSX Premium 2 : 26 - 30.11.01 (5 jours) Contract Follow-up (F) : 26.11.01 (1/2 journée) Object-Oriented Analysis and Design :  27 - 30.11.2001  (4 days) Hands-on Object-Oriented Design and Programming with C++ :  11 - 13.12.2...

  14. PLACES AVAILABLE

    CERN Multimedia

    Monique Duval

    2002-01-01

    Places are available in the following courses: ELEC-2002 : Spring Term :  9, 11, 16, 18, 23, 25, 30.4.02 (7 * 2.5 hours) Object-Oriented Analysis & Design: 16 - 19.4.02  (4 days) The CERN Engineering Data Management System for Advanced users:  16.4.02  (1 day) Migration from AutoCAD 14 towards AutoCAD Mechanical6 PowerPack:  17 - 19.4 and 2 &3.5.02  (5 days) AutoCAD - niveau 1 : 22, 23, 29, 30.4 et 6, 7.5.02 (6 jours) LabVIEW base 1 : 22 - 24.4.02 (3 jours) CLEAN 2002 : working in a cleanroom:  24.4.02  (half-day, pm) LabVIEW DSC (F) 25 & 26.4.02 (2 jours) AutoCAD : Mise à jour AutoCAD r-14 vers 2002 : 25 & 26.4.02 (2 jours) Cotations selon les normes GPS de l'ISO : 29 - 30.4.02 (2 jours) Introduction to the CERN Engineering Data Management System:  7.5.02  (1 day) LabVIEW Basics 2 : 13 & 14.5.02 (2 days) AutoCAD Mechanical 6 PowerPack (F) : 13-...

  15. PLACES AVAILABLE

    CERN Multimedia

    Monique Duval

    2002-01-01

    Places are available in the following courses: Introduction to the CERN Engineering Data Management System:  7.5.02  (1 day) LabVIEW Basics 2: 13 & 14.5.02 (2 days) AutoCAD Mechanical 6 PowerPack (F) : 13-14, 17, 21, 27-28.5.02 (6 jours) WorldFIP - Généralités : 14.5.2002 (1/2 journée) WorldFIP - Développer avec MicroFIP HANDLER : 14.5 - après-midi, 15.5.02 - matin (1 jour) WorldFIP - FullFIP FDM : FIP Device Manager (F) : 15.5 - après-midi, 16.5.02 - matin (1 jour) LabVIEW DAQ (F) : 15 & 16.5.02 (2 jours) EXCEL 2000 - niveau 2 : 22 & 23.5.02 (2 jours) The CERN Engineering Data Management System for Advanced users:  30.5.02  (1 day) LabVIEW Basics 1:  3 - 5.6.02  (3 days) AutoCAD 2002 - condensé : 4 - 6.6.02 (3 jours) LabVIEW DAQ (E):  6 & 7.6.02  (2 days) AutoCAD 2002 - Level 1:  10 - ...

  16. PLACES AVAILABLE

    CERN Multimedia

    Monique Duval

    2002-01-01

    Places are available in the following courses: The CERN Engineering Data Management System for Advanced users : 16.4.02  (1 day) Migration from AutoCAD 14 towards AutoCAD Mechanical6 PowerPack:  17 - 19.4 and 2 &3.5.02  (5 days) AutoCAD - niveau 1 : 22, 23, 29, 30.4 et 6, 7.5.02 (6 jours) LabVIEW base 1 : 22 - 24.4.02 (3 jours) CLEAN 2002 : working in a cleanroom:  24.4.02  (half-day, pm) LabVIEW DSC (F) 25 & 26.4.02 (2 jours) AutoCAD : Mise à jour AutoCAD r-14 vers 2002 : 25 & 26.4.02 (2 jours) Cotations selon les normes GPS de l'ISO : 29 - 30.4.02 (2 jours) Introduction to the CERN Engineering Data Management System:  7.5.02  (1 day) LabVIEW Basics 2: 13 & 14.5.02 (2 days) AutoCAD Mechanical 6 PowerPack (F) : 13-14, 17, 21, 27-28.5.02 (6 jours) WorldFIP - Généralités : 14.5.2002 (1/2 journée) WorldFIP - Développer avec Micr...

  17. PLACES AVAILABLE

    CERN Multimedia

    Monique Duval

    2002-01-01

    Places are available in the following courses: LabVIEW Basics 2: 13 & 14.5.02 (2 days) WorldFIP - Généralités : 14.5.2002 (1/2 journée) WorldFIP - Développer avec MicroFIP HANDLER : 14.5 - après-midi, 15.5.02 - matin (1 jour) WorldFIP - FullFIP FDM : FIP Device Manager (F) : 15.5 - après-midi, 16.5.02 - matin (1 jour) LabVIEW DAQ (F) : 15 & 16.5.02 (2 jours) EXCEL 2000 - niveau 2 : 22 & 23.5.02 (2 jours) The CERN Engineering Data Management System for Advanced users:  30.5.02  (1 day) LabVIEW Basics 1:  3 - 5.6.02  (3 days) AutoCAD 2002 - condensé : 4 - 6.6.02 (3 jours) LabVIEW DAQ (E):  6 & 7.6.02  (2 days) AutoCAD 2002 - Level 1:  10 - 12 and 24 - 26.6.02  (6 days) If you wish to participate in one of these courses, please discuss with your supervisor and apply electronically directly from the c...

  18. PLACES AVAILABLE

    CERN Multimedia

    Monique Duval

    2002-01-01

    Places are available in the following courses: LabVIEW base 1 : 22 - 24.4.02 (3 jours) CLEAN 2002 : working in a cleanroom:  24.4.02  (half-day, pm) LabVIEW DSC (F) 25 & 26.4.02 (2 jours) AutoCAD : Mise à jour AutoCAD r-14 vers 2002 : 25 & 26.4.02 (2 jours) Cotations selon les normes GPS de l'ISO : 29 - 30.4.02 (2 jours) Introduction to the CERN Engineering Data Management System:  7.5.02  (1 day) LabVIEW Basics 2: 13 & 14.5.02 (2 days) AutoCAD Mechanical 6 PowerPack (F) : 13-14, 17, 21, 27-28.5.02 (6 jours) WorldFIP - Généralités : 14.5.2002 (1/2 journée) WorldFIP - Développer avec MicroFIP HANDLER : 14.5 - après-midi, 15.5.02 - matin (1 jour) WorldFIP - FullFIP FDM : FIP Device Manager (F) : 15.5 - après-midi, 16.5.02 - matin (1 jour) LabVIEW DAQ (F) : 15 & 16.5.02 (2 jours) EXCEL 2000 - niveau 2 : 22 & 23.5.02 (2 jours)...

  19. VECTOR INTEGRATION

    NARCIS (Netherlands)

    Thomas, E. G. F.

    2012-01-01

    This paper deals with the theory of integration of scalar functions with respect to a measure with values in a, not necessarily locally convex, topological vector space. It focuses on the extension of such integrals from bounded measurable functions to the class of integrable functions, proving

  20. Damping Wind and Wave Loads on a Floating Wind Turbine

    DEFF Research Database (Denmark)

    Christiansen, Søren; Bak, Thomas; Knudsen, Torben

    2013-01-01

    Offshore wind energy capitalizes on the higher and less turbulent wind speeds at sea. To enable deployment of wind turbines in deep-water locations, structures are being explored, where wind turbines are placed on a floating platform. This combined structure presents a new control problem, due......, and we show the influence that both wind speed, wave frequencies and misalignment between wind and waves have on the system dynamics. A new control model is derived that extends standard turbine models to include the hydrodynamics, additional platform degrees of freedom, the platform mooring system...

  1. Wind energy: Overcoming inadequate wind and modeling uncertainties

    Energy Technology Data Exchange (ETDEWEB)

    Kane, Vivek

    2010-09-15

    'Green Energy' is the call of the day, and significance of Wind Energy can never be overemphasized. But the key question here is - What if the wind resources are inadequate? Studies reveal that the probability of finding favorable wind at a given place on land is only 15%. Moreover, there are inherent uncertainties associated with wind business. Can we overcome inadequate wind resources? Can we scientifically quantify uncertainty and model it to make business sense? This paper proposes a solution, by way of break-through Wind Technologies, combined with advanced tools for Financial Modeling, enabling vital business decisions.

  2. Wind Tunnel Measurements at LM Wind Power

    DEFF Research Database (Denmark)

    Bertagnolio, Franck

    2012-01-01

    This section presents the results obtained during the experimental campaign that was conducted in the wind tunnel at LM Wind Power in Lunderskov from August 16th to 26th, 2010. The goal of this study is to validate the so-called TNO trailing edge noise model through measurements of the boundary...... layer turbulence characteristics and the far-field noise generated by the acoustic scattering of the turbulent boundary layer vorticies as they convect past the trailing edge. This campaign was conducted with a NACA0015 airfoil section that was placed in the wind tunnel section. It is equipped with high...

  3. Reliability Analysis of Wind Turbines

    DEFF Research Database (Denmark)

    Toft, Henrik Stensgaard; Sørensen, John Dalsgaard

    2008-01-01

    In order to minimise the total expected life-cycle costs of a wind turbine it is important to estimate the reliability level for all components in the wind turbine. This paper deals with reliability analysis for the tower and blades of onshore wind turbines placed in a wind farm. The limit states...... consideres are in the ultimate limit state (ULS) extreme conditions in the standstill position and extreme conditions during operating. For wind turbines, where the magnitude of the loads is influenced by the control system, the ultimate limit state can occur in both cases. In the fatigue limit state (FLS......) the reliability level for a wind turbine placed in a wind farm is considered, and wake effects from neighbouring wind turbines is taken into account. An illustrative example with calculation of the reliability for mudline bending of the tower is considered. In the example the design is determined according...

  4. Wind: new wind markets

    International Nuclear Information System (INIS)

    Cameron, A.

    2005-01-01

    The June 2005 edition of 'Wind Force 12' suggests that wind could generate 12% of global electricity requirements by 2020. But what moves a potential market into an emerging one? Geographical factors include a good wind resource, plenty of open space and the ability to get the generated electricity to end-users. A country's political framework is equally important, with fixed price systems, renewable quota systems and political will all playing a part. Some potential wind markets around the world are thought to have the conditions necessary to become key players in the wind industry. The emerging markets in countries such as Australia, Brazil, Canada, France, Japan and the Philippines are highlighted as examples

  5. Retrieval of vertical wind profiles during monsoon from satellite ...

    Indian Academy of Sciences (India)

    Complex EOF analysis; cloud motion vector winds; wind profiles; retrieval; monsoon. Proc. Indian Acad. Sci. .... The data gaps are removed using simple linear interpolation .... retrieved via standard linear regression using the two independent ...

  6. An introduction to vectors, vector operators and vector analysis

    CERN Document Server

    Joag, Pramod S

    2016-01-01

    Ideal for undergraduate and graduate students of science and engineering, this book covers fundamental concepts of vectors and their applications in a single volume. The first unit deals with basic formulation, both conceptual and theoretical. It discusses applications of algebraic operations, Levi-Civita notation, and curvilinear coordinate systems like spherical polar and parabolic systems and structures, and analytical geometry of curves and surfaces. The second unit delves into the algebra of operators and their types and also explains the equivalence between the algebra of vector operators and the algebra of matrices. Formulation of eigen vectors and eigen values of a linear vector operator are elaborated using vector algebra. The third unit deals with vector analysis, discussing vector valued functions of a scalar variable and functions of vector argument (both scalar valued and vector valued), thus covering both the scalar vector fields and vector integration.

  7. Places disponibles/Places available

    CERN Multimedia

    2004-01-01

    Si vous désirez participer à l'un des cours suivants, veuillez en discuter avec votre superviseur et vous inscrire électroniquement en direct depuis les pages de description des cours dans le Web que vous trouvez à l'adresse : http://www.cern.ch/Training/ ou remplissez une « demande de formation » disponible auprès du Secrétariat de votre Division ou de votre DTO (Délégué divisionnaire à la formation). Les places seront attribuées dans l'ordre de réception des inscriptions. If you wish to participate in one of the following courses, please discuss with your supervisor and apply electronically directly from the course description pages that can be found on the Web at: http://www.cern.ch/Training/ or fill in an "application for training" form available from your Divisional Secretariat or from your DTO (Divisional Training Off...

  8. Wind Farm Wake: The Horns Rev Photo Case

    Directory of Open Access Journals (Sweden)

    Pierre-Elouan Réthoré

    2013-02-01

    Full Text Available The aim of the paper is to examine the nowadays well-known wind farm wake photographs taken on 12 February 2008 at the offshore Horns Rev 1 wind farm. The meteorological conditions are described from observations from several satellite sensors quantifying clouds, surface wind vectors and sea surface temperature as well as ground-based information at and near the wind farm, including Supervisory Control and Data Acquisition (SCADA data. The SCADA data reveal that the case of fog formation occurred 12 February 2008 on the 10:10 UTC. The fog formation is due to very special atmospheric conditions where a layer of cold humid air above a warmer sea surface re-condensates to fog in the wake of the turbines. The process is fed by warm humid air up-drafted from below in the counter-rotating swirl generated by the clock-wise rotating rotors. The condensation appears to take place primarily in the wake regions with relatively high axial velocities and high turbulent kinetic energy. The wind speed is near cut-in and most turbines produce very little power. The rotational pattern of spiraling bands produces the large-scale structure of the wake fog.

  9. Technical Training: Places available

    CERN Multimedia

    Monique Duval

    2004-01-01

    If you wish to participate in one of the following courses, please discuss with your supervisor and apply electronically directly from the course description pages that can be found on the Web at: http://www.cern.ch/Training/ or fill in an 'application for training' form available from your Divisional Secretariat or from your DTO (Divisional Training Officer). Applications will be accepted in the order of their receipt. The number of places available may vary. Please check our Web site to find out the current availability. Places are available in the following courses: Hands-on Introduction to Python Programming: 1 - 3.9.2004 (3 days - free course) Introduction au VHDL et utilisation du simulateur NCVHDL de CADENCE : 7 & 8.9.2004 (2 jours) AutoCAD 2002 - niveau 1 : 13, 14, 23, 24.9.2004 (4 jours) Programmation STEP7 niveau 1 : 14-17.9.2004 (4 jours) FrontPage 2003 - niveau 1 : 20 & 21.9.2004 (2 jours) Word 2003 - niveau 2 : 27 & 28.9.2004 (2 jours) Introduction à Wind...

  10. Wind Energy

    International Nuclear Information System (INIS)

    Rodriguez D, J.M.

    1998-01-01

    The general theory of the wind energy conversion systems is presented. The availability of the wind resource in Colombia and the ranges of the speed of the wind in those which is possible economically to use the wind turbines are described. It is continued with a description of the principal technological characteristics of the wind turbines and are split into wind power and wind-powered pumps; and its use in large quantities grouped in wind farms or in autonomous systems. Finally, its costs and its environmental impact are presented

  11. Emerging vector borne diseases – incidence through vectors

    Directory of Open Access Journals (Sweden)

    Sara eSavic

    2014-12-01

    Full Text Available Vector borne diseases use to be a major public health concern only in tropical and subtropical areas, but today they are an emerging threat for the continental and developed countries also. Nowdays, in intercontinetal countries, there is a struggle with emerging diseases which have found their way to appear through vectors. Vector borne zoonotic diseases occur when vectors, animal hosts, climate conditions, pathogens and susceptible human population exist at the same time, at the same place. Global climate change is predicted to lead to an increase in vector borne infectious diseases and disease outbreaks. It could affect the range and popultion of pathogens, host and vectors, transmission season, etc. Reliable surveilance for diseases that are most likely to emerge is required. Canine vector borne diseases represent a complex group of diseases including anaplasmosis, babesiosis, bartonellosis, borreliosis, dirofilariosis, erlichiosis, leishmaniosis. Some of these diseases cause serious clinical symptoms in dogs and some of them have a zoonotic potential with an effect to public health. It is expected from veterinarians in coordination with medical doctors to play a fudamental role at primeraly prevention and then treatment of vector borne diseases in dogs. The One Health concept has to be integrated into the struggle against emerging diseases.During a four year period, from 2009-2013, a total number of 551 dog samples were analysed for vector borne diseases (borreliosis, babesiosis, erlichiosis, anaplasmosis, dirofilariosis and leishmaniasis in routine laboratory work. The analysis were done by serological tests – ELISA for borreliosis, dirofilariosis and leishmaniasis, modified Knott test for dirofilariosis and blood smear for babesiosis, erlichiosis and anaplasmosis. This number of samples represented 75% of total number of samples that were sent for analysis for different diseases in dogs. Annually, on avarege more then half of the samples

  12. Extreme Winds from the NCEP/NCAR Reanalysis Data

    DEFF Research Database (Denmark)

    Larsén, Xiaoli Guo; Mann, Jakob

    2009-01-01

    wind. We examined extreme winds in different places where the strongest wind events are weather phenomena of different scales, including the mid-latitude lows in Denmark, channelling winds in the Gulf of Suez, typhoons in the western North Pacific, cyclones in the Caribbean Sea, local strong winds...

  13. Characterization of wind velocities in the wake of a full scale wind turbine using three ground-based synchronized WindScanners

    DEFF Research Database (Denmark)

    Yazicioglu, Hasan; Angelou, Nikolas; Mikkelsen, Torben Krogh

    2016-01-01

    The wind energy community is in need of detailed full-field measurements in the wake of wind turbines. Here, three dimensional(3D) wind vector field measurements obtained in the near-wake region behind a full-scale test turbine are presented. Specifically, the wake of a NEG Nordtank turbine...

  14. Optimal Operation of Wind Turbines Based on Support Vector Machine and Differential Evolution Algorithm%基于支持向量机和微分进化算法的风电机优化运行

    Institute of Scientific and Technical Information of China (English)

    彭春华; 相龙阳; 刘刚; 易洪京

    2012-01-01

    Output control of wind turbines is the key item in the operation of wind farm. In view of complicated relations among wind turbine output, wind speed and blade pitch angle, it is hard to establish a versatile and accurate mathematical model. For this reason, a new mode to optimize wind turbine output is proposed: firstly a model for nonlinear fitting between wind turbine output and operational parameters is built; then based on the built model and the variation of wind speed and adopting the high-efficient differential evolution algorithm, the blade pitch angle of wind turbine is optimized fast and dynamically. Using the proposed method, the dynamic relation between wind speed and optimal blade pitch angle can be established. Simulation results of the proposed method show that the output of wind turbine can be effectively uprated, thus the feasibility of the proposed method is verified.%风电机出力控制是风电场运行过程中的一个关键问题。针对风电机出力与风速和桨距角之间存在非常复杂的关系,很难建立通用准确的数学模型,提出了一种新的风电机出力优化模式,即首先通过支持向量机算法建立风电机出力与运行参数之间的非线性拟合模型,并基于此模型和风速的变化,采用高效的微分进化算法对风力机桨距角进行快速动态优化,从而实现风电机出力最大化。以鄱阳湖长岭风电场风电机组实际运行数据进行了仿真应用与分析。结果表明通过优化风力机桨距角可有效地提高风电机出力,验证了文中方法的可行性和优越性。采用文中方法可准确建立风速与最优桨距角的动态对应关系,为风电机的优化运行提供了科学的指导。

  15. Performance of Wind Pump Prototype

    African Journals Online (AJOL)

    Mulu

    Mekelle University, Mekelle, Ethiopia (*mul_at@yahoo.com). ABSTRACT. A wind ... balanced rotor power and reciprocating pump, hence did not consider the effect of pump size. ... Keywords: Wind pump, Windmill, Performance testing, Pump efficiency, Pump discharge, ... Unfortunately, in rural places, where the houses are.

  16. COOP Wind and Radiation Observations

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Wind and radiation data from stations in the National Weather Service Cooperative Observers Network. Some precipitation and pressure forms are mistakenly placed in...

  17. Emerging Vector-Borne Diseases - Incidence through Vectors.

    Science.gov (United States)

    Savić, Sara; Vidić, Branka; Grgić, Zivoslav; Potkonjak, Aleksandar; Spasojevic, Ljubica

    2014-01-01

    Vector-borne diseases use to be a major public health concern only in tropical and subtropical areas, but today they are an emerging threat for the continental and developed countries also. Nowadays, in intercontinental countries, there is a struggle with emerging diseases, which have found their way to appear through vectors. Vector-borne zoonotic diseases occur when vectors, animal hosts, climate conditions, pathogens, and susceptible human population exist at the same time, at the same place. Global climate change is predicted to lead to an increase in vector-borne infectious diseases and disease outbreaks. It could affect the range and population of pathogens, host and vectors, transmission season, etc. Reliable surveillance for diseases that are most likely to emerge is required. Canine vector-borne diseases represent a complex group of diseases including anaplasmosis, babesiosis, bartonellosis, borreliosis, dirofilariosis, ehrlichiosis, and leishmaniosis. Some of these diseases cause serious clinical symptoms in dogs and some of them have a zoonotic potential with an effect to public health. It is expected from veterinarians in coordination with medical doctors to play a fundamental role at primarily prevention and then treatment of vector-borne diseases in dogs. The One Health concept has to be integrated into the struggle against emerging diseases. During a 4-year period, from 2009 to 2013, a total number of 551 dog samples were analyzed for vector-borne diseases (borreliosis, babesiosis, ehrlichiosis, anaplasmosis, dirofilariosis, and leishmaniasis) in routine laboratory work. The analysis was done by serological tests - ELISA for borreliosis, dirofilariosis, and leishmaniasis, modified Knott test for dirofilariosis, and blood smear for babesiosis, ehrlichiosis, and anaplasmosis. This number of samples represented 75% of total number of samples that were sent for analysis for different diseases in dogs. Annually, on average more then half of the samples

  18. Wind speed errors for LIDARs and SODARs in complex terrain

    International Nuclear Information System (INIS)

    Bradley, S

    2008-01-01

    All commercial LIDARs and SODARs are monostatic and hence sample distributed volumes to construct wind vector components. We use an analytic potential flow model to estimate errors arising for a range of LIDAR and SODAR configurations on hills and escarpments. Wind speed errors peak at a height relevant to wind turbines and can be typically 20%

  19. Wind speed errors for LIDARs and SODARs in complex terrain

    Energy Technology Data Exchange (ETDEWEB)

    Bradley, S [Physics Department, The University of Auckland, Private Bag 92019, Auckland (New Zealand) and School of Computing, Science and Engineering, University of Salford, M5 4WT (United Kingdom)], E-mail: s.bradley@auckland.ac.nz

    2008-05-01

    All commercial LIDARs and SODARs are monostatic and hence sample distributed volumes to construct wind vector components. We use an analytic potential flow model to estimate errors arising for a range of LIDAR and SODAR configurations on hills and escarpments. Wind speed errors peak at a height relevant to wind turbines and can be typically 20%.

  20. Low-speed wind tunnel investigation of the static stability and control characteristics of an advanced turboprop configuration with the propellers placed over the tail. M.S. Thesis

    Science.gov (United States)

    Rhodes, Graham Scott

    1990-01-01

    An exploratory wind tunnel investigation was performed in the 30 x 60 foot wind tunnel to determine the low speed static stability and control characteristics into the deep stall regime of an advanced turboprop aircraft with the propellers located over the horizontal tail. By this arrangement, the horizontal tail could potentially provide acoustic shielding to reduce the high community noise caused by the propeller blades. The current configuration was a generic turboprop model equipped with 1 foot diameter single rotating eight bladed propellers that were designed for efficient cruise operation at a Mach number of 0.8. The data presented is static force data. The effects of power on the configuration characteristics were generally favorable. An arrangement with the propellers rotating with the outboard blades moving down was found to have significantly higher installed thrust than an arrangement with the propellers rotating with the inboard blades moving down. The primary unfavorable effect was a large pitch trim change which occurred with power, but the trim change could be minimized with a proper configuration design.

  1. Endurance Wind Power : practical insights into small wind

    International Nuclear Information System (INIS)

    Hicks, D.

    2008-01-01

    This presentation discussed practical issues related to purchasing and installing small wind turbines in Canada. Wind power capacity can be estimated by looking at provincial wind maps as well as by seeking wind data at local airports. Wind resources are typically measured at heights of between 20 meters and 50 m. The height of a wind turbine tower can significantly increase the turbine's wind generating capacity. Turbine rotors should always be placed 30 feet higher than obstacles within 500 feet. Many provinces have now mandated utilities to accept renewable energy resources from grid-connected wind energy plants. Net billing systems are used to determine the billing relationship between power-producing consumers and the utilities who will buy the excess power and sell it to other consumers. Utilities are not yet mandated to purchase excess power, and it is likely that federal and provincial legislation will be needed to ensure that net billing systems continue to grow. Many Canadian municipalities have no ordinances related to wind turbine placements. Consumers interested in purchasing small wind turbines should ensure that the turbine has been certified by an accredited test facility and has an adequate safety system. The noise of the turbine as well as its power performance in relation to the purchaser's needs must also be considered. It was concluded that small wind turbines can provide a means for electricity consumers to reduce their carbon footprint and hedge against the inflationary costs of fossil-fuelled energy resources. tabs., figs

  2. Downscaling of Airborne Wind Energy Systems

    NARCIS (Netherlands)

    Fechner, U.; Schmehl, R.

    2016-01-01

    Airborne wind energy systems provide a novel solution to harvest wind energy from altitudes that can not be reached by wind turbines with a similar nominal generator power. The use of a lightweight but strong tether in place of an expensive tower provides an additional cost advantage, next to the

  3. Annoyance rating of wind turbine noise

    International Nuclear Information System (INIS)

    Iredale, R.A.

    1992-01-01

    This paper proposes a simple criterion for noise limitation of wind turbines: 'The La A50 from a Wind Farm should not exceeding the L A50 of the wind generated background plus 5dB at any place of potential complaint'. This criterion is then examined and developed in the light of experience to date with turbine noise complaint and procedures. (author)

  4. Georeferenced Population Datasets of Mexico (GEO-MEX): Urban Place GIS Coverage of Mexico

    Data.gov (United States)

    National Aeronautics and Space Administration — The Urban Place GIS Coverage of Mexico is a vector based point Geographic Information System (GIS) coverage of 696 urban places in Mexico. Each Urban Place is...

  5. Wind energy

    International Nuclear Information System (INIS)

    Kotevski, Darko

    2003-01-01

    Wind is not only free, it is inexhaustible. Wind energy has come a very long way since the prototypes of just 20 years ago. today's wind turbines are state-of-the-art technology - modular and quick to install anywhere where there is sufficient wind potential to provide secure, centralised or distributed generation. It is a global phenomenon, the world's fastest growing energy sector, a clean and effective modern technology that completely avoids pollution and thus reducing the 'green house' effect. (Original)

  6. Raster images vectorization system

    OpenAIRE

    Genytė, Jurgita

    2006-01-01

    The problem of raster images vectorization was analyzed and researched in this work. Existing vectorization systems are quite expensive, the results are inaccurate, and the manual vectorization of a large number of drafts is impossible. That‘s why our goal was to design and develop a new raster images vectorization system using our suggested automatic vectorization algorithm and the way to record results in a new universal vectorial file format. The work consists of these main parts: analysis...

  7. Wind Structure and Wind Loading

    DEFF Research Database (Denmark)

    Brorsen, Michael

    The purpose of this note is to provide a short description of wind, i.e. of the flow in the atmosphere of the Earth and the loading caused by wind on structures. The description comprises: causes to the generation of windhe interaction between wind and the surface of the Earthhe stochastic nature...

  8. Place Branding in Systems of Place

    DEFF Research Database (Denmark)

    Zenker, Sebastian; Andéhn, Mikael

    2015-01-01

    , this presents a challenge, since the role of a place in this system of geographical abstractions constitutes a piece of information more vital than any other in defining the place. Our understanding of places cannot be separated from their scale, and any effort at managing the reputation and meaning.......g. the European Union or Africa). Using the example of nation branding for Sudan and Slovenia, one can identify supranational places such as “sub-Saharan Africa” or “Eastern Europe”, carrying their own highly salient and often negative meaning in much of the Western world. We explore how association to a system...

  9. Model Predictive Control of Wind Turbines

    DEFF Research Database (Denmark)

    Henriksen, Lars Christian

    Wind turbines play a major role in the transformation from a fossil fuel based energy production to a more sustainable production of energy. Total-cost-of-ownership is an important parameter when investors decide in which energy technology they should place their capital. Modern wind turbines...... the need for maintenance of the wind turbine. Either way, better total-cost-of-ownership for wind turbine operators can be achieved by improved control of the wind turbines. Wind turbine control can be improved in two ways, by improving the model on which the controller bases its design or by improving...

  10. Offshore wind power in the Aegean Sea

    DEFF Research Database (Denmark)

    Hasager, Charlotte Bay; Badger, Merete; Hahmann, Andrea N.

    hub heights at around 100 m using a combination of satellite wind fields and the long-term climate of atmospheric stability from the mesoscale model (Badger et al. 2016). The result of the mean wind speed at hub-height for the Aegean Sea is shown in Figure 1. The map shows the stability dependent......, where the spatial variations in wind speed are very high, accurate resource mapping is of great importance as the produced wind power is proportional to the cubed wind speed. It is challenging to model the wind resource and it is costly to measure from the ground at every place of interest. Maps based...

  11. Kochen-Specker vectors

    International Nuclear Information System (INIS)

    Pavicic, Mladen; Merlet, Jean-Pierre; McKay, Brendan; Megill, Norman D

    2005-01-01

    We give a constructive and exhaustive definition of Kochen-Specker (KS) vectors in a Hilbert space of any dimension as well as of all the remaining vectors of the space. KS vectors are elements of any set of orthonormal states, i.e., vectors in an n-dimensional Hilbert space, H n , n≥3, to which it is impossible to assign 1s and 0s in such a way that no two mutually orthogonal vectors from the set are both assigned 1 and that not all mutually orthogonal vectors are assigned 0. Our constructive definition of such KS vectors is based on algorithms that generate MMP diagrams corresponding to blocks of orthogonal vectors in R n , on algorithms that single out those diagrams on which algebraic (0)-(1) states cannot be defined, and on algorithms that solve nonlinear equations describing the orthogonalities of the vectors by means of statistically polynomially complex interval analysis and self-teaching programs. The algorithms are limited neither by the number of dimensions nor by the number of vectors. To demonstrate the power of the algorithms, all four-dimensional KS vector systems containing up to 24 vectors were generated and described, all three-dimensional vector systems containing up to 30 vectors were scanned, and several general properties of KS vectors were found

  12. Wind power

    International Nuclear Information System (INIS)

    Gipe, P.

    2007-01-01

    This book is a translation of the edition published in the USA under the title of ''wind power: renewable energy for home, farm and business''. In the wake of mass blackouts and energy crises, wind power remains a largely untapped resource of renewable energy. It is a booming worldwide industry whose technology, under the collective wing of aficionados like author Paul Gipe, is coming of age. Wind Power guides us through the emergent, sometimes daunting discourse on wind technology, giving frank explanations of how to use wind technology wisely and sound advice on how to avoid common mistakes. Since the mid-1970's, Paul Gipe has played a part in nearly every aspect of wind energy development from installing small turbines to promoting wind energy worldwide. As an American proponent of renewable energy, Gipe has earned the acclaim and respect of European energy specialists for years, but his arguments have often fallen on deaf ears at home. Today, the topic of wind power is cropping up everywhere from the beaches of Cape Cod to the Oregon-Washington border, and one wind turbine is capable of producing enough electricity per year to run 200 average American households. Now, Paul Gipe is back to shed light on this increasingly important energy source with a revised edition of Wind Power. Over the course of his career, Paul Gipe has been a proponent, participant, observer, and critic of the wind industry. His experience with wind has given rise to two previous books on the subject, Wind Energy Basics and Wind Power for Home and Business, which have sold over 50,000 copies. Wind Power for Home and Business has become a staple for both homeowners and professionals interested in the subject, and now, with energy prices soaring, interest in wind power is hitting an all-time high. With chapters on output and economics, Wind Power discloses how much you can expect from each method of wind technology, both in terms of energy and financial savings. The book updated models

  13. Vector regression introduced

    Directory of Open Access Journals (Sweden)

    Mok Tik

    2014-06-01

    Full Text Available This study formulates regression of vector data that will enable statistical analysis of various geodetic phenomena such as, polar motion, ocean currents, typhoon/hurricane tracking, crustal deformations, and precursory earthquake signals. The observed vector variable of an event (dependent vector variable is expressed as a function of a number of hypothesized phenomena realized also as vector variables (independent vector variables and/or scalar variables that are likely to impact the dependent vector variable. The proposed representation has the unique property of solving the coefficients of independent vector variables (explanatory variables also as vectors, hence it supersedes multivariate multiple regression models, in which the unknown coefficients are scalar quantities. For the solution, complex numbers are used to rep- resent vector information, and the method of least squares is deployed to estimate the vector model parameters after transforming the complex vector regression model into a real vector regression model through isomorphism. Various operational statistics for testing the predictive significance of the estimated vector parameter coefficients are also derived. A simple numerical example demonstrates the use of the proposed vector regression analysis in modeling typhoon paths.

  14. Using Particle Image Velocimetry to Measure the Wind in a Winnowing Chamber

    OpenAIRE

    Matsui, Masami; Inoue, Eiji; Kuwano, Tomoko; Mori, Ken; Furuno, Yuko

    2003-01-01

    The array of vectors for the winnowing wind in the threshing unit was investigated uding PIV in order to improve the winnowing accuracy. It is difficult to measure wind velocities at many points simultaneously using the anemometer. However, visualization of the winnowing wind was possible using the tracer and laser beam. Futhermore, The PIV method made it possible to measure an array of vectors for the winnowing wind. The results produced by PIV concurred with the results of conventional meth...

  15. Model county ordinance for wind projects

    Energy Technology Data Exchange (ETDEWEB)

    Bain, D.A. [Oregon Office of Energy, Portland, OR (United States)

    1997-12-31

    Permitting is a crucial step in the development cycle of a wind project and permits affect the timing, cost, location, feasibility, layout, and impacts of wind projects. Counties often have the lead responsibility for permitting yet few have appropriate siting regulations for wind projects. A model ordinance allows a county to quickly adopt appropriate permitting procedures. The model county wind ordinance developed for use by northwest states is generally applicable across the country and counties seeking to adopt siting or zoning regulations for wind will find it a good starting place. The model includes permitting procedures for wind measurement devices and two types of wind systems. Both discretionary and nondiscretionary standards apply to wind systems and a conditional use permit would be issued. The standards, criteria, conditions for approval, and process procedures are defined for each. Adaptation examples for the four northwest states are provided along with a model Wind Resource Overlay Zone.

  16. Continuing bonds and place.

    Science.gov (United States)

    Jonsson, Annika; Walter, Tony

    2017-08-01

    Where do people feel closest to those they have lost? This article explores how continuing bonds with a deceased person can be rooted in a particular place or places. Some conceptual resources are sketched, namely continuing bonds, place attachment, ancestral places, home, reminder theory, and loss of place. The authors use these concepts to analyze interview material with seven Swedes and five Britons who often thought warmly of the deceased as residing in a particular place and often performing characteristic actions. The destruction of such a place, by contrast, could create a troubling, haunting absence, complicating the deceased's absent-presence.

  17. Superconducting wind turbine generators

    DEFF Research Database (Denmark)

    Mijatovic, Nenad

    cryostat design, where a concept with 20 W of heat transfer is achieved. Following the setup description, the focus turns to the electromagnetic design of the HTS machine. Particularly, an approach to increase the performance of HTS coils and the influence of the armature reaction to the HTS field winding...... magnetic characteristic with respect to the critical current. I have showed that the potential for the reduction of HTS conductor can be significant, if the coils are placed strategically, whereby the coils wound with BSCCO performed 40% better depending on the placement in the field winding. The 2G coils...... were less sensitive to the placement which made them particularly useful for high magnetic field regions in the eld winding. The second design approach proposed and tested was to use multiple current supplies which allowed each coil to operate close to its critical current. I have demonstrated...

  18. VectorBase

    Data.gov (United States)

    U.S. Department of Health & Human Services — VectorBase is a Bioinformatics Resource Center for invertebrate vectors. It is one of four Bioinformatics Resource Centers funded by NIAID to provide web-based...

  19. Lidar-Observed Stress Vectors and Veer in the Atmospheric Boundary Layer

    DEFF Research Database (Denmark)

    Berg, Jacob; Mann, Jakob; Patton, Edward G.

    2013-01-01

    This study demonstrates that a pulsed wind lidar is a reliable instrument for measuring angles between horizontal vectors of significance in the atmospheric boundary layer. Three different angles are considered: the wind turning, the angle between the stress vector and the mean wind direction......, and the angle between the stress vector and the vertical gradient of the mean velocity vector. The latter is assumed to be zero by the often applied turbulent-viscosity hypothesis, so that the stress vector can be described through the vertical gradient of velocity. In the atmospheric surface layer, where...... the Coriolis force is negligible, this is supposedly a good approximation. High-resolution large-eddy simulation data show that this is indeed the case even beyond the surface layer. In contrast, through analysis of WindCube lidar measurements supported by sonic measurements, the study shows that it is only...

  20. Generalization of concurrence vectors

    International Nuclear Information System (INIS)

    Yu Changshui; Song Heshan

    2004-01-01

    In this Letter, based on the generalization of concurrence vectors for bipartite pure state with respect to employing tensor product of generators of the corresponding rotation groups, we generalize concurrence vectors to the case of mixed states; a new criterion of separability of multipartite pure states is given out, for which we define a concurrence vector; we generalize the vector to the case of multipartite mixed state and give out a good measure of free entanglement

  1. Vector Network Coding

    OpenAIRE

    Ebrahimi, Javad; Fragouli, Christina

    2010-01-01

    We develop new algebraic algorithms for scalar and vector network coding. In vector network coding, the source multicasts information by transmitting vectors of length L, while intermediate nodes process and combine their incoming packets by multiplying them with L X L coding matrices that play a similar role as coding coefficients in scalar coding. Our algorithms for scalar network jointly optimize the employed field size while selecting the coding coefficients. Similarly, for vector co...

  2. Vector Network Coding Algorithms

    OpenAIRE

    Ebrahimi, Javad; Fragouli, Christina

    2010-01-01

    We develop new algebraic algorithms for scalar and vector network coding. In vector network coding, the source multicasts information by transmitting vectors of length L, while intermediate nodes process and combine their incoming packets by multiplying them with L x L coding matrices that play a similar role as coding c in scalar coding. Our algorithms for scalar network jointly optimize the employed field size while selecting the coding coefficients. Similarly, for vector coding, our algori...

  3. Convexity and Marginal Vectors

    NARCIS (Netherlands)

    van Velzen, S.; Hamers, H.J.M.; Norde, H.W.

    2002-01-01

    In this paper we construct sets of marginal vectors of a TU game with the property that if the marginal vectors from these sets are core elements, then the game is convex.This approach leads to new upperbounds on the number of marginal vectors needed to characterize convexity.An other result is that

  4. Custodial vector model

    DEFF Research Database (Denmark)

    Becciolini, Diego; Franzosi, Diogo Buarque; Foadi, Roshan

    2015-01-01

    We analyze the Large Hadron Collider (LHC) phenomenology of heavy vector resonances with a $SU(2)_L\\times SU(2)_R$ spectral global symmetry. This symmetry partially protects the electroweak S-parameter from large contributions of the vector resonances. The resulting custodial vector model spectrum...

  5. Wind energy.

    Science.gov (United States)

    Leithead, W E

    2007-04-15

    From its rebirth in the early 1980s, the rate of development of wind energy has been dramatic. Today, other than hydropower, it is the most important of the renewable sources of power. The UK Government and the EU Commission have adopted targets for renewable energy generation of 10 and 12% of consumption, respectively. Much of this, by necessity, must be met by wind energy. The US Department of Energy has set a goal of 6% of electricity supply from wind energy by 2020. For this potential to be fully realized, several aspects, related to public acceptance, and technical issues, related to the expected increase in penetration on the electricity network and the current drive towards larger wind turbines, need to be resolved. Nevertheless, these challenges will be met and wind energy will, very likely, become increasingly important over the next two decades. An overview of the technology is presented.

  6. Wind noise under a pine tree canopy.

    Science.gov (United States)

    Raspet, Richard; Webster, Jeremy

    2015-02-01

    It is well known that infrasonic wind noise levels are lower for arrays placed in forests and under vegetation than for those in open areas. In this research, the wind noise levels, turbulence spectra, and wind velocity profiles are measured in a pine forest. A prediction of the wind noise spectra from the measured meteorological parameters is developed based on recent research on wind noise above a flat plane. The resulting wind noise spectrum is the sum of the low frequency wind noise generated by the turbulence-shear interaction near and above the tops of the trees and higher frequency wind noise generated by the turbulence-turbulence interaction near the ground within the tree layer. The convection velocity of the low frequency wind noise corresponds to the wind speed above the trees while the measurements showed that the wind noise generated by the turbulence-turbulence interaction is near stationary and is generated by the slow moving turbulence adjacent to the ground. Comparison of the predicted wind noise spectrum with the measured wind noise spectrum shows good agreement for four measurement sets. The prediction can be applied to meteorological estimates to predict the wind noise under other pine forests.

  7. Unconventional wind machine

    International Nuclear Information System (INIS)

    Sheff, J.R.

    1979-01-01

    It is the purpose of this paper to introduce an unconventional wind machine which has economics comparable with nuclear power and is already available in the public market place. Specifically, up to about 17 MWE could be saved for other uses such as sale in most 1000 MWE plants of any type - nuclear, oil, gas, peat, or wood - which use conventional electrically driven fans in their cooling towers. 10 refs

  8. Performance of the CORDEX regional climate models in simulating offshore wind and wind potential

    Science.gov (United States)

    Kulkarni, Sumeet; Deo, M. C.; Ghosh, Subimal

    2018-03-01

    This study is oriented towards quantification of the skill addition by regional climate models (RCMs) in the parent general circulation models (GCMs) while simulating wind speed and wind potential with particular reference to the Indian offshore region. To arrive at a suitable reference dataset, the performance of wind outputs from three different reanalysis datasets is evaluated. The comparison across the RCMs and their corresponding parent GCMs is done on the basis of annual/seasonal wind statistics, intermodel bias, wind climatology, and classes of wind potential. It was observed that while the RCMs could simulate spatial variability of winds, well for certain subregions, they generally failed to replicate the overall spatial pattern, especially in monsoon and winter. Various causes of biases in RCMs were determined by assessing corresponding maps of wind vectors, surface temperature, and sea-level pressure. The results highlight the necessity to carefully assess the RCM-yielded winds before using them for sensitive applications such as coastal vulnerability and hazard assessment. A supplementary outcome of this study is in form of wind potential atlas, based on spatial distribution of wind classes. This could be beneficial in suitably identifying viable subregions for developing offshore wind farms by intercomparing both the RCM and GCM outcomes. It is encouraging that most of the RCMs and GCMs indicate that around 70% of the Indian offshore locations in monsoon would experience mean wind potential greater than 200 W/m2.

  9. My Place Is Not Your Place

    DEFF Research Database (Denmark)

    Zenker, Sebastian; Beckmann, Suzanne C.

    2013-01-01

    Purpose – Cities increasingly compete with each other for attracting tourists, investors, companies, or residents. Marketers therefore focus on establishing the city as a brand, disregarding that the perception and knowledge of a city differ dramatically between the target audiences. Hence, place...... branding should emphasize much more the perceptions of the different target groups and develop strategies for advanced place brand management. The aim of this paper is to assess the important discrepancies between the city brand perceptions of different target groups with the help of network analysis......-ended-question survey with 334 participants. Findings – Structural differences for the city brand perceptions of two different target groups and the differences between perceptions of an external and internal target group are highlighted. The results and the managerial implications for place marketers are discussed...

  10. Populated Places of Iowa

    Data.gov (United States)

    Iowa State University GIS Support and Research Facility — This coverage contains points that represent populated places, ie. cities, towns, villages or any other named place where people live. The coverage was developed...

  11. Rotations with Rodrigues' vector

    International Nuclear Information System (INIS)

    Pina, E

    2011-01-01

    The rotational dynamics was studied from the point of view of Rodrigues' vector. This vector is defined here by its connection with other forms of parametrization of the rotation matrix. The rotation matrix was expressed in terms of this vector. The angular velocity was computed using the components of Rodrigues' vector as coordinates. It appears to be a fundamental matrix that is used to express the components of the angular velocity, the rotation matrix and the angular momentum vector. The Hamiltonian formalism of rotational dynamics in terms of this vector uses the same matrix. The quantization of the rotational dynamics is performed with simple rules if one uses Rodrigues' vector and similar formal expressions for the quantum operators that mimic the Hamiltonian classical dynamics.

  12. EDITORIAL: Wind energy

    Science.gov (United States)

    Mann, Jakob; Nørkær Sørensen, Jens; Morthorst, Poul-Erik

    2008-01-01

    addressed within the issue is how much conventional power production can be replaced by the ceaseless wind, with the question of how Greece's target of 29% renewables by 2020 is to be met efficiently. Other topics include an innovative way to determine the power curve of a turbine experimentally more accurately, the use of fluid dynamics tools to investigate the implications of placing vortex generators on wind turbine blades (thereby possibly improving their efficiency) and a study of the perception of wind turbine noise. It turns out that a small but significant fraction of wind turbine neighbours feel that turbine generated noise impairs their ability to rest. The annoyance is correlated with a negative attitude towards the visual impact on the landscape, but what is cause and effect is too early to say. As mentioned there is a rush for wind turbines in many countries. However, this positive development for the global climate is currently limited by practical barriers. One bottleneck is the difficulties for the sub-suppliers of gears and other parts to meet the demand. Another is the difficulties to meet the demand for engineers specialized in wind. For that reason the Technical University of Denmark (DTU) recently launched the world's first Wind Energy Masters Program. Here and elsewhere in the world of wind education and research we should really speed up now, as our chances of contributing to emission free energy production and a healthier global climate have never been better. Focus on Wind Energy Contents The articles below represent the first accepted contributions and further additions will appear in the near future. Wind turbines—low level noise sources interfering with restoration? Eja Pedersen and Kerstin Persson Waye On the effect of spatial dispersion of wind power plants on the wind energy capacity credit in Greece George Caralis, Yiannis Perivolaris, Konstantinos Rados and Arthouros Zervos Large-eddy simulation of spectral coherence in a wind turbine wake

  13. The importance of places and place branding

    NARCIS (Netherlands)

    Kovács, Z.; Musterd, S.; Musterd, S.; Kovács, Z.

    2013-01-01

    In the analytical part of this study, we highlight that, despite globalisation and growing uniformity, there is still an important role for place itself in the location decisions of economic players. Part III of this volume deals with this. Even though city-regions across the world have become

  14. Wind energy impact of turbulence

    CERN Document Server

    Hölling, Michae; Ivanell, Stefan

    2014-01-01

    This book presents the results of the seminar ""Wind Energy and the Impact of Turbulence on the Conversion Process"" which was supported from three societies, namely the EUROMech, EAWE and ERCOFATC and took place in Oldenburg, Germany in spring 2012.The seminar was one of the first scientific meetings devoted to the common topic of wind energy and basic turbulence. The established community of researchers working on the challenging puzzle of turbulence for decades met the quite young community of researchers, who face the upcoming challenges in the fast growing field of wind energy application

  15. Grid Integration of Offshore Wind | Wind | NREL

    Science.gov (United States)

    Grid Integration of Offshore Wind Grid Integration of Offshore Wind Much can be learned from the existing land-based integration research for handling the variability and uncertainty of the wind resource Arklow Bank offshore wind park consists of seven GE Wind 3.6-MW wind turbines. Integration and

  16. Quality and Control of Water Vapor Winds

    Science.gov (United States)

    Jedlovec, Gary J.; Atkinson, Robert J.

    1996-01-01

    Water vapor imagery from the geostationary satellites such as GOES, Meteosat, and GMS provides synoptic views of dynamical events on a continual basis. Because the imagery represents a non-linear combination of mid- and upper-tropospheric thermodynamic parameters (three-dimensional variations in temperature and humidity), video loops of these image products provide enlightening views of regional flow fields, the movement of tropical and extratropical storm systems, the transfer of moisture between hemispheres and from the tropics to the mid- latitudes, and the dominance of high pressure systems over particular regions of the Earth. Despite the obvious larger scale features, the water vapor imagery contains significant image variability down to the single 8 km GOES pixel. These features can be quantitatively identified and tracked from one time to the next using various image processing techniques. Merrill et al. (1991), Hayden and Schmidt (1992), and Laurent (1993) have documented the operational procedures and capabilities of NOAA and ESOC to produce cloud and water vapor winds. These techniques employ standard correlation and template matching approaches to wind tracking and use qualitative and quantitative procedures to eliminate bad wind vectors from the wind data set. Techniques have also been developed to improve the quality of the operational winds though robust editing procedures (Hayden and Veldon 1991). These quality and control approaches have limitations, are often subjective, and constrain wind variability to be consistent with model derived wind fields. This paper describes research focused on the refinement of objective quality and control parameters for water vapor wind vector data sets. New quality and control measures are developed and employed to provide a more robust wind data set for climate analysis, data assimilation studies, as well as operational weather forecasting. The parameters are applicable to cloud-tracked winds as well with minor

  17. Wind Energy

    Energy Technology Data Exchange (ETDEWEB)

    Beurskens, H.J.M. [SET Analysis, Kievitlaan 26, 1742 AD Schagen (Netherlands); Brand, A.J. [Energy research Centre of the Netherlands ECN, Unit Wind Energy, P.O. Box 1, 1755 ZG Petten (Netherlands)

    2013-02-15

    Over the years, wind energy has become a major source of renewable energy worldwide. The present chapter addresses the wind resource, which is available for exploitation for large-scale electricity production, and its specific physical properties. Furthermore, the technical options available to convert the energy of the air flow into mechanical energy and electricity are described. Specific problems of large-scale integration of wind energy into the grid as well as the present and future market developments are described in this chapter. Finally, environmental aspects are discussed briefly.

  18. Electrostatic Solitary Waves in the Solar Wind: Evidence for Instability at Solar Wind Current Sheets

    Science.gov (United States)

    Malaspina, David M.; Newman, David L.; Wilson, Lynn Bruce; Goetz, Keith; Kellogg, Paul J.; Kerstin, Kris

    2013-01-01

    A strong spatial association between bipolar electrostatic solitary waves (ESWs) and magnetic current sheets (CSs) in the solar wind is reported here for the first time. This association requires that the plasma instabilities (e.g., Buneman, electron two stream) which generate ESWs are preferentially localized to solar wind CSs. Distributions of CS properties (including shear angle, thickness, solar wind speed, and vector magnetic field change) are examined for differences between CSs associated with ESWs and randomly chosen CSs. Possible mechanisms for producing ESW-generating instabilities at solar wind CSs are considered, including magnetic reconnection.

  19. Place in Transition

    DEFF Research Database (Denmark)

    Mikkelsen, Jacob Bjerre; Lange, Ida Sofie Gøtzsche

    from the 'Everyday World'. Within mobilities studies, research has focused on different aspects and consequences of the post-oil society (see Dennis & Urry 2009, Urry 2013). This paper discusses the conception of place within the enclosed 'Oil World' with point of departure in relocation...... and redefinition of oil rigs from an urban design perspective. The paper constitutes a theoretical basis for future design scenarios - exemplified through visionary urban design proposals for a specific site in the city of Esbjerg, Denmark. Relocating rigs to an urban context initiates discussions of conception...... of 'Place' questioning the fixity of 'Place' (Jensen 2010). Scoped through a relational sense of place (Massey 1993) and the potential of exploring new relations between places (Burns & Kahn 2005), the paper challenges the notion of 'Place as God' (Hvattum 2010). These places in transition contest...

  20. Determination of key parameters of vector multifractal vector fields

    Science.gov (United States)

    Schertzer, D. J. M.; Tchiguirinskaia, I.

    2017-12-01

    For too long time, multifractal analyses and simulations have been restricted to scalar-valued fields (Schertzer and Tchiguirinskaia, 2017a,b). For instance, the wind velocity multifractality has been mostly analysed in terms of scalar structure functions and with the scalar energy flux. This restriction has had the unfortunate consequences that multifractals were applicable to their full extent in geophysics, whereas it has inspired them. Indeed a key question in geophysics is the complexity of the interactions between various fields or they components. Nevertheless, sophisticated methods have been developed to determine the key parameters of scalar valued fields. In this communication, we first present the vector extensions of the universal multifractal analysis techniques to multifractals whose generator belong to a Levy-Clifford algebra (Schertzer and Tchiguirinskaia, 2015). We point out further extensions noting the increased complexity. For instance, the (scalar) index of multifractality becomes a matrice. Schertzer, D. and Tchiguirinskaia, I. (2015) `Multifractal vector fields and stochastic Clifford algebra', Chaos: An Interdisciplinary Journal of Nonlinear Science, 25(12), p. 123127. doi: 10.1063/1.4937364. Schertzer, D. and Tchiguirinskaia, I. (2017) `An Introduction to Multifractals and Scale Symmetry Groups', in Ghanbarian, B. and Hunt, A. (eds) Fractals: Concepts and Applications in Geosciences. CRC Press, p. (in press). Schertzer, D. and Tchiguirinskaia, I. (2017b) `Pandora Box of Multifractals: Barely Open ?', in Tsonis, A. A. (ed.) 30 Years of Nonlinear Dynamics in Geophysics. Berlin: Springer, p. (in press).

  1. Magnetic vector field tag and seal

    Science.gov (United States)

    Johnston, Roger G.; Garcia, Anthony R.

    2004-08-31

    One or more magnets are placed in a container (preferably on objects inside the container) and the magnetic field strength and vector direction are measured with a magnetometer from at least one location near the container to provide the container with a magnetic vector field tag and seal. The location(s) of the magnetometer relative to the container are also noted. If the position of any magnet inside the container changes, then the measured vector fields at the these locations also change, indicating that the tag has been removed, the seal has broken, and therefore that the container and objects inside may have been tampered with. A hollow wheel with magnets inside may also provide a similar magnetic vector field tag and seal. As the wheel turns, the magnets tumble randomly inside, removing the tag and breaking the seal.

  2. Wind power

    International Nuclear Information System (INIS)

    2009-01-01

    At the end of 2008,the European wind power capacity had risen to 65,247 MW which is a 15,1% increase on 2007. The financial crisis does not appear to have any real consequences of the wind power sector's activity in 2008. At the end of 2008 the European Union accommodated 53,9% of the world's wind power capacity. The top ten countries in terms of installed wind capacities are: 1) Usa with 25,388 MW, 2) Germany with 23,903 MW, 3) Spain with 16,740 MW, 4) China with 12,200 MW, 5) India with 9,645 MW, 6) Italy with 3,736 MW, 7) France with 3,542 MW, 8) U.K. with 3,406 MW, 9) Denmark with 3,166 MW and 10) Portugal with 2,862 MW. (A.C.)

  3. Analysis of wind bias change with respect to time at Cape Kennedy, Florida, and Vandenberg AFB, California

    Science.gov (United States)

    Adelfang, S. I.

    1978-01-01

    A statistical analysis is presented of the temporal variability of wind vectors at 1 km altitude intervals from 0 to 27 km altitude after applying a digital filter to the original wind profile data sample.

  4. Quantifying the Role of Atmospheric Forcing in Ice Edge Retreat and Advance Including Wind-Wave Coupling

    Science.gov (United States)

    2015-09-30

    Low-Level Profiles, Pressure, Temperature, Humidity Rawinsonde (Kite, Tethered Balloon , Unmanned Aerial vehicle) Wave Characteristics, Wind wave and...Thermistor, Ship intake, Manual Bucket Tropospheric Profiles, 4/day – Pressure, Temperature, Humidity, Wind Vector Rawinsonde (Weather Balloon

  5. Wind power

    Energy Technology Data Exchange (ETDEWEB)

    1979-01-01

    This publication describes some of the technical, economic, safety and institutional considerations involved in the selection, installation and evaluation of a wind generation system. This information is presented, where possible, in practical, non-technical terms. The first four sections provide background information, theory, and general knowledge, while the remaining six sections are of a more specific nature to assist the prospective owner of a wind generator in his calculations and selections. Meteorological information is provided relating to the wind regime in Nova Scotia. The section on cost analysis discusses some of the factors and considerations which must be examined in order to provide a logical comparison between the alternatives of electricity produced from other sources. The final two sections are brief summaries of the regulations and hazards pertaining to the use of wind generators. The cost of wind-generated electricity is high compared to present Nova Scotia Power Corporation rates, even on Sable Island, Nova Scotia's highest wind area. However, it may be observed that Sable Island is one of the areas of Nova Scotia which is not presently supplied through the power grid and, particularly if there was a significant increase in the price of diesel oil, wind-generated electricity may well be the most economical alternative in that area. Generally speaking, however, where a consumer can purchase electricity at the normal domestic rate, wind generators are not economical, and they will not become economical unless there is a great reduction in their cost, an great increase in electricity rates, or both. Includes glossary. 23 figs., 11 tabs.

  6. Place-Specific Computing

    DEFF Research Database (Denmark)

    Messeter, Jörn

    2009-01-01

    An increased interest in the notion of place has evolved in interaction design based on the proliferation of wireless infrastructures, developments in digital media, and a ‘spatial turn’ in computing. In this article, place-specific computing is suggested as a genre of interaction design that add......An increased interest in the notion of place has evolved in interaction design based on the proliferation of wireless infrastructures, developments in digital media, and a ‘spatial turn’ in computing. In this article, place-specific computing is suggested as a genre of interaction design...... that addresses the shaping of interactions among people, place-specific resources and global socio-technical networks, mediated by digital technology, and influenced by the structuring conditions of place. The theoretical grounding for place-specific computing is located in the meeting between conceptions...... of place in human geography and recent research in interaction design focusing on embodied interaction. Central themes in this grounding revolve around place and its relation to embodiment and practice, as well as the social, cultural and material aspects conditioning the enactment of place. Selected...

  7. Coastal Ohio Wind Project

    Energy Technology Data Exchange (ETDEWEB)

    Gorsevski, Peter [Bowling Green State Univ., OH (United States); Afjeh, Abdollah [Univ. of Toledo, OH (United States); Jamali, Mohsin [Univ. of Toledo, OH (United States); Bingman, Verner [Bowling Green State Univ., OH (United States)

    2014-04-04

    The Coastal Ohio Wind Project intends to address problems that impede deployment of wind turbines in the coastal and offshore regions of Northern Ohio. The project evaluates different wind turbine designs and the potential impact of offshore turbines on migratory and resident birds by developing multidisciplinary research, which involves wildlife biology, electrical and mechanical engineering, and geospatial science. Firstly, the project conducts cost and performance studies of two- and three-blade wind turbines using a turbine design suited for the Great Lakes. The numerical studies comprised an analysis and evaluation of the annual energy production of two- and three-blade wind turbines to determine the levelized cost of energy. This task also involved wind tunnel studies of model wind turbines to quantify the wake flow field of upwind and downwind wind turbine-tower arrangements. The experimental work included a study of a scaled model of an offshore wind turbine platform in a water tunnel. The levelized cost of energy work consisted of the development and application of a cost model to predict the cost of energy produced by a wind turbine system placed offshore. The analysis found that a floating two-blade wind turbine presents the most cost effective alternative for the Great Lakes. The load effects studies showed that the two-blade wind turbine model experiences less torque under all IEC Standard design load cases considered. Other load effects did not show this trend and depending on the design load cases, the two-bladed wind turbine showed higher or lower load effects. The experimental studies of the wake were conducted using smoke flow visualization and hot wire anemometry. Flow visualization studies showed that in the downwind turbine configuration the wake flow was insensitive to the presence of the blade and was very similar to that of the tower alone. On the other hand, in the upwind turbine configuration, increasing the rotor blade angle of attack

  8. Supergravity inspired vector curvaton

    International Nuclear Information System (INIS)

    Dimopoulos, Konstantinos

    2007-01-01

    It is investigated whether a massive Abelian vector field, whose gauge kinetic function is growing during inflation, can be responsible for the generation of the curvature perturbation in the Universe. Particle production is studied and it is shown that the vector field can obtain a scale-invariant superhorizon spectrum of perturbations with a reasonable choice of kinetic function. After inflation the vector field begins coherent oscillations, during which it corresponds to pressureless isotropic matter. When the vector field dominates the Universe, its perturbations give rise to the observed curvature perturbation following the curvaton scenario. It is found that this is possible if, after the end of inflation, the mass of the vector field increases at a phase transition at temperature of order 1 TeV or lower. Inhomogeneous reheating, whereby the vector field modulates the decay rate of the inflaton, is also studied

  9. Custodial vector model

    Science.gov (United States)

    Becciolini, Diego; Franzosi, Diogo Buarque; Foadi, Roshan; Frandsen, Mads T.; Hapola, Tuomas; Sannino, Francesco

    2015-07-01

    We analyze the Large Hadron Collider (LHC) phenomenology of heavy vector resonances with a S U (2 )L×S U (2 )R spectral global symmetry. This symmetry partially protects the electroweak S parameter from large contributions of the vector resonances. The resulting custodial vector model spectrum and interactions with the standard model fields lead to distinct signatures at the LHC in the diboson, dilepton, and associated Higgs channels.

  10. Vector Differential Calculus

    OpenAIRE

    HITZER, Eckhard MS

    2002-01-01

    This paper treats the fundamentals of the vector differential calculus part of universal geometric calculus. Geometric calculus simplifies and unifies the structure and notation of mathematics for all of science and engineering, and for technological applications. In order to make the treatment self-contained, I first compile all important geometric algebra relationships,which are necesssary for vector differential calculus. Then differentiation by vectors is introduced and a host of major ve...

  11. Implicit Real Vector Automata

    Directory of Open Access Journals (Sweden)

    Jean-François Degbomont

    2010-10-01

    Full Text Available This paper addresses the symbolic representation of non-convex real polyhedra, i.e., sets of real vectors satisfying arbitrary Boolean combinations of linear constraints. We develop an original data structure for representing such sets, based on an implicit and concise encoding of a known structure, the Real Vector Automaton. The resulting formalism provides a canonical representation of polyhedra, is closed under Boolean operators, and admits an efficient decision procedure for testing the membership of a vector.

  12. Risky Zoographies: The Limits of Place in Avian Flu Management

    Directory of Open Access Journals (Sweden)

    Natalie Porter

    2012-11-01

    Full Text Available Global anxieties about avian influenza stem from a growing recognition that highly-virulent, highly-mobile disease vectors infiltrate human spaces in ways that are difficult to perceive, and even more difficult to manage. This article analyses a participatory health intervention in Việt Nam to explore how avian influenza threats challenge long-held understandings of animals’ place in the environment and society. In this intervention, poultry farmers collaborated with health workers to illustrate maps of avian flu risks in their communities. Participant-observation of the risk-mapping exercises shows that health workers treated poultry as commodities, and located these animals in environments that could be transformed and dominated by humans. However, these maps did not sufficiently represent the physical and social landscapes where humans and poultry coexist in Việt Nam. As such, farmers located poultry in environments dominated by risky nonhuman forces such as winds, waterways, and other organisms. I argue that these divergent risk maps demonstrate how ecological factors, interpersonal networks, and global market dynamics combine to engender a variety of interspecies relationships, which in turn shape the location of disease risks in space. I develop the term risky zoographies to signal the emergence of competing descriptions of animals and their habitats in zoonotic disease contexts. This concept suggests that as wild animals, livestock products, and microbial pathogens continue to globalise, place-based health interventions that limit animals to particular locales are proving inadequate. Risky zoographies signal the inextricability of nonhuman animals from human spaces, and reveal interspecies interactions that transect and transcend environments.

  13. Vectorized Monte Carlo

    International Nuclear Information System (INIS)

    Brown, F.B.

    1981-01-01

    Examination of the global algorithms and local kernels of conventional general-purpose Monte Carlo codes shows that multigroup Monte Carlo methods have sufficient structure to permit efficient vectorization. A structured multigroup Monte Carlo algorithm for vector computers is developed in which many particle events are treated at once on a cell-by-cell basis. Vectorization of kernels for tracking and variance reduction is described, and a new method for discrete sampling is developed to facilitate the vectorization of collision analysis. To demonstrate the potential of the new method, a vectorized Monte Carlo code for multigroup radiation transport analysis was developed. This code incorporates many features of conventional general-purpose production codes, including general geometry, splitting and Russian roulette, survival biasing, variance estimation via batching, a number of cutoffs, and generalized tallies of collision, tracklength, and surface crossing estimators with response functions. Predictions of vectorized performance characteristics for the CYBER-205 were made using emulated coding and a dynamic model of vector instruction timing. Computation rates were examined for a variety of test problems to determine sensitivities to batch size and vector lengths. Significant speedups are predicted for even a few hundred particles per batch, and asymptotic speedups by about 40 over equivalent Amdahl 470V/8 scalar codes arepredicted for a few thousand particles per batch. The principal conclusion is that vectorization of a general-purpose multigroup Monte Carlo code is well worth the significant effort required for stylized coding and major algorithmic changes

  14. Vectors and their applications

    CERN Document Server

    Pettofrezzo, Anthony J

    2005-01-01

    Geared toward undergraduate students, this text illustrates the use of vectors as a mathematical tool in plane synthetic geometry, plane and spherical trigonometry, and analytic geometry of two- and three-dimensional space. Its rigorous development includes a complete treatment of the algebra of vectors in the first two chapters.Among the text's outstanding features are numbered definitions and theorems in the development of vector algebra, which appear in italics for easy reference. Most of the theorems include proofs, and coordinate position vectors receive an in-depth treatment. Key concept

  15. Symbolic computer vector analysis

    Science.gov (United States)

    Stoutemyer, D. R.

    1977-01-01

    A MACSYMA program is described which performs symbolic vector algebra and vector calculus. The program can combine and simplify symbolic expressions including dot products and cross products, together with the gradient, divergence, curl, and Laplacian operators. The distribution of these operators over sums or products is under user control, as are various other expansions, including expansion into components in any specific orthogonal coordinate system. There is also a capability for deriving the scalar or vector potential of a vector field. Examples include derivation of the partial differential equations describing fluid flow and magnetohydrodynamics, for 12 different classic orthogonal curvilinear coordinate systems.

  16. Ecology of Malaria Vectors in a Rainforest Suburban Community of ...

    African Journals Online (AJOL)

    User

    2011-04-19

    Apr 19, 2011 ... Key words: Malaria, Mosquito, Vectors, Ecology, Suburban, Community. ... including host bloodmeal preferences, time and place of biting and resting .... Five species of mosquitoes namely Aedes albopictus, Culex tigripes,.

  17. 2008 WIND TECHNOLOGIES MARKET REPORT

    Energy Technology Data Exchange (ETDEWEB)

    Wiser, Ryan H.; Bolinger, Mark; Barbose, G.; Mills, A.; Rosa, A.; Porter, K.; Fink, S.; Tegen, S.; Musial, W.; Oteri, F.; Heimiller, D.; Rberts, B.; Belyeu, K.; Stimmel, R.

    2009-07-15

    domestic wind power market, including federal and state policy drivers, transmission issues, and grid integration. Finally, the report concludes with a preview of possible near- to medium-term market developments. This version of the Annual Report updates data presented in the previous editions, while highlighting key trends and important new developments from 2008. New to this edition is an executive summary of the report and an expanded final section on near- to medium-term market development. The report concentrates on larger-scale wind applications, defined here as individual turbines or projects that exceed 50 kW in size. The U.S. wind power sector is multifaceted, however, and also includes smaller, customer-sited wind turbines used to power the needs of residences, farms, and businesses. Data on these applications are not the focus of this report, though a brief discussion on Distributed Wind Power is provided on page 4. Much of the data included in this report were compiled by Berkeley Lab, and come from a variety of sources, including the American Wind Energy Association (AWEA), the Energy Information Administration (EIA), and the Federal Energy Regulatory Commission (FERC). The Appendix provides a summary of the many data sources used in the report. Data on 2008 wind capacity additions in the United States are based on information provided by AWEA; some minor adjustments to those data may be expected. In other cases, the data shown here represent only a sample of actual wind projects installed in the United States; furthermore, the data vary in quality. As such, emphasis should be placed on overall trends, rather than on individual data points. Finally, each section of this document focuses on historical market information, with an emphasis on 2008; with the exception of the final section, the report does not seek to forecast future trends.

  18. Gearless wind power generator

    Energy Technology Data Exchange (ETDEWEB)

    Soederlund, L.; Ridanpaeae, P.; Vihriaelae, H.; Peraelae, R. [Tampere Univ. of Technology (Finland). Lab. of Electricity and Magnetism

    1998-10-01

    In the project a 100 kW axial flux permanent magnet wind power generator has been designed. The toroidal stator with air gap winding is placed between two rotating discs with permanent magnets. The magnet material is NdBFe due to its excellent magnetic properties compared to other materials. This type of topology enables a very large number of poles compared to conventional machine of the same size. A large number of poles is required to achieve a low rotational speed and consequently a direct driven system. The stator winding is formed by rectangular coils. The end winding is very short leading to small resistive losses. On the other hand, the absence of iron teeth causes eddy current losses in the conductors. These can be restricted to an acceptable level by keeping the wire diameter and flux density small. This means that the number of phases should be large. Several independent three phase systems may be used. The toothless stator also means that the iron losses are small and there exists no cogging torque

  19. The value of place

    Science.gov (United States)

    Dentzau, Michael W.

    2014-03-01

    This commentary seeks to expand the dialogue on place-based science education presented in Katie Lynn Brkich's article, where the connections fifth grade students make between their formal earth science curriculum and their lived experiences are highlighted. The disconnect between the curriculum the students are offered and their immediate environment is clear, and we are presented with examples of how they strive to make connections between the content and what they are familiar with—namely their surroundings. "Place" is identified as a term with complex meanings and interpretations, even in the scope of place-based science education, and understanding how the term is used in any given scenario is essential to understanding the implications of place-based education. Is place used as a location, locale or a sense of place? To understand "place" is to acknowledge that for the individual, it is highly situational, cultural and personal. It is just such attributes that make place-based education appealing, and potentially powerful, pedagogically on one hand, yet complex for implementation on the other. The argument is posed that place is particularly important in the context of education about the environment, which in its simplest manifestation, connects formal science curriculum to resources that are local and tangible to students. The incorporation of place in such a framework seeks to bridge the gap between formal school science subjects and students' lived experiences, yet acknowledges the tensions that can arise between accommodating place meanings and the desire to acculturate students into the language of the scientific community. The disconnect between guiding policy frameworks and the reality of the Next Generation Science Standards is addressed opening an avenue for further discussion of the importance of socio-cultural frameworks of science learning in an ever increasing era of accountability.

  20. Mechanics of interrill erosion with wind-driven rain

    Science.gov (United States)

    The vector physics of wind-driven rain (WDR) differs from that of wind-free rain, and the interrill soil detachment equations in the Water Erosion Prediction Project (WEPP) model were not originally developed to deal with this phenomenon. This article provides an evaluation of the performance of the...

  1. A bistatic sodar for precision wind profiling in complex terrain

    DEFF Research Database (Denmark)

    Bradley, Stuart; Hünerbein, Sabine Von; Mikkelsen, Torben

    2012-01-01

    A new ground-based wind profiling technology-a scanned bistatic sodar-is described. The motivation for this design is to obtain a "mastlike"wind vector profile in a single atmospheric column extending from the ground to heights of more than 200 m. The need for this columnar profiling arises from ...

  2. Technical training: places available

    CERN Multimedia

    HR Department

    2007-01-01

    CERN Technical Training: Open Courses (April - June 2007) The following course sessions are currently scheduled in the framework of the CERN Technical Training Programme 2007:   AutoCAD 2006 - niveau 1 (course in French): 25.4.- 26.4.2007 & 2.5. - 3.5.2007 (4 days in 2 modules, 5 places available) AutoCAD 2006 - niveau 1 (course in French): 27.6.- 28.6.2007 & 3.7. - 4.7.2007 (4 days in 2 modules, 5 places available) AutoCAD Mechanical 2006 (course in French) 21.6.-22.6.2007 (2 days, 8 places available) * NEW COURSE* Automate de securite S7 (course in French) 14.5.-16.5.2007 (3 days, 4 places available) * NEW COURSE* Automate de securite S7 (course in French): 9.5.-11.5.2007 (3 days, 4 places available) JCOP - Joint PVSS-JCOP Frameswork (course in English): 21.5.-25.5.2007 (5 days, 12 places available) JCOP - Finite State Machines in the JCOP Frameswork (course in English): 12.6.-14.6.2007 (3 days, 12 places available) LabVIEW Basics 1 (in English): 2.-4.5.2007 (3 days, 7 places ...

  3. A Sense of Place

    Directory of Open Access Journals (Sweden)

    Rachel Black

    2012-09-01

    Full Text Available People increasingly want to know where their food and wine comes from and who produces it. This is part of developing a taste of place, or what the French call terroir. The academic and industry debates surrounding the concept of terroir are explored, and the efforts of Massachusetts wine producers to define their sense of place are discussed.

  4. Place in transition

    DEFF Research Database (Denmark)

    Mikkelsen, Jacob Bjerre; Lange, Ida Sofie Gøtzsche

    2017-01-01

    World. This paper discusses the conception of place in the Oil World, with the relocation and transformation of oil rigs from an urban design perspective as its point of departure, using Esbjerg, Denmark, as a case study. Combining a theoretical understanding of places as relational with a design...

  5. Connecting people to place

    NARCIS (Netherlands)

    Horlings, L.G.

    2016-01-01

    The article describes a process of preparing a research design on place-shaping, as outcome of a process of co-design between academic actors and non-academic actors in Brazil, South Africa and The Netherlands, taking place in the context of the project TRANSPLACE. The joint research design

  6. The Case for Place

    Science.gov (United States)

    Thomas, Lisa Carlucci

    2012-01-01

    Bookstores, record stores, libraries, Facebook: these places--both physical and virtual--demonstrate an established and essential purpose as centers of community, expertise, convenience, immediacy, and respect. Yet as digital, mobile, and social shifts continue to transform culture and interactions, these spaces and places transform, too.…

  7. Grid support capabilities of wind turbines

    DEFF Research Database (Denmark)

    Michalke, Gabriele; Hansen, Anca Daniela

    2013-01-01

    Wind power has gained a significant penetration level in several power systems all over the world. Due to this reason modern wind turbines are requested to contribute to power system support. Power system operators have thus introduced grid codes, which specify a set of requirements for wind...... turbines, such as fault ride-through and reactive power supply during voltage sags. To date different wind turbine concepts exist on the market comprising different control features in order to provide ancillary services to the power system. In the first place the present chapter emphasizes the most...... important issues related to wind power grid integration. Then different wind turbine concepts are characterized and their grid support capabilities are analysed and compared. Simulation cases are presented in which the respective wind turbine concepts are subjected to a voltage dip specified in a grid code....

  8. Non-Place

    DEFF Research Database (Denmark)

    formulation. The anthology contains 17 articles engaged directly in the application, retrofitting and broadening of the concept of the non-place to a range of literary and media texts, as well as the merging of this concept to other theoretical concepts by e.g. Michel Foucault, Gilles Deleuze, Alain Badiou......We spend more and more of our everyday lives in what Marc Augé calls non-places – homogenous, but bland places of transit. This anthology addresses the representations of non-places in literature, culture and media, and critiques and re-actualizes Augé’s work twenty years after its initial...... Jutland, and many others. This anthology is the seventh publication in the IRGiC series and it springs from a research seminar held at Aalborg University in May 2013: “Non-Place in Literature, Media and Culture”....

  9. Place-Specific Computing

    DEFF Research Database (Denmark)

    Messeter, Jörn; Johansson, Michael

    project place- specific computing is explored through design oriented research. This article reports six pilot studies where design students have designed concepts for place-specific computing in Berlin (Germany), Cape Town (South Africa), Rome (Italy) and Malmö (Sweden). Background and arguments...... for place-specific computing as a genre of interaction design are described. A total number of 36 design concepts designed for 16 designated zones in the four cities are presented. An analysis of the design concepts is presented indicating potentials, possibilities and problems as directions for future......An increased interest in the notion of place has evolved in interaction design. Proliferation of wireless infrastructure, developments in digital media, and a ‘spatial turn’ in computing provides the base for place-specific computing as a suggested new genre of interaction design. In the REcult...

  10. Technical training - places available

    CERN Multimedia

    2012-01-01

    If you would like more information on a course, or for any other inquiry/suggestions, please contact Technical.Training@cern.ch Valeria Perez Reale, Learning Specialist, Technical Programme Coordinator (Tel.: 62424) Eva Stern and Elise Romero, Technical Training Administration (Tel.: 74924) HR Department »Electronics design Next Session Duration Language Availability Comprehensive VHDL for FPGA Design 08-Oct-12 to 12-Oct-12 5 days English 3 places available Foundations of Electromagnetism and Magnet Design (EMAG) 14-Nov-12 to 27-Nov-12 6 days English 20 places available Impacts de la suppression du plomb (RoHS) en électronique 26-Oct-12 to 26-Oct-12 8 hours French 15 places available Introduction to VHDL 10-Oct-12 to 11-Oct-12 2 days English 7 places available LabVIEW Real Time and FPGA 13-Nov-12 to 16-Nov-12 5 days French 5 places available »Mechanical design Next Se...

  11. Vector-Vector Scattering on the Lattice

    Science.gov (United States)

    Romero-López, Fernando; Urbach, Carsten; Rusetsky, Akaki

    2018-03-01

    In this work we present an extension of the LüScher formalism to include the interaction of particles with spin, focusing on the scattering of two vector particles. The derived formalism will be applied to Scalar QED in the Higgs Phase, where the U(1) gauge boson acquires mass.

  12. Selection vector filter framework

    Science.gov (United States)

    Lukac, Rastislav; Plataniotis, Konstantinos N.; Smolka, Bogdan; Venetsanopoulos, Anastasios N.

    2003-10-01

    We provide a unified framework of nonlinear vector techniques outputting the lowest ranked vector. The proposed framework constitutes a generalized filter class for multichannel signal processing. A new class of nonlinear selection filters are based on the robust order-statistic theory and the minimization of the weighted distance function to other input samples. The proposed method can be designed to perform a variety of filtering operations including previously developed filtering techniques such as vector median, basic vector directional filter, directional distance filter, weighted vector median filters and weighted directional filters. A wide range of filtering operations is guaranteed by the filter structure with two independent weight vectors for angular and distance domains of the vector space. In order to adapt the filter parameters to varying signal and noise statistics, we provide also the generalized optimization algorithms taking the advantage of the weighted median filters and the relationship between standard median filter and vector median filter. Thus, we can deal with both statistical and deterministic aspects of the filter design process. It will be shown that the proposed method holds the required properties such as the capability of modelling the underlying system in the application at hand, the robustness with respect to errors in the model of underlying system, the availability of the training procedure and finally, the simplicity of filter representation, analysis, design and implementation. Simulation studies also indicate that the new filters are computationally attractive and have excellent performance in environments corrupted by bit errors and impulsive noise.

  13. Brane vector phenomenology

    International Nuclear Information System (INIS)

    Clark, T.E.; Love, S.T.; Nitta, Muneto; Veldhuis, T. ter; Xiong, C.

    2009-01-01

    Local oscillations of the brane world are manifested as massive vector fields. Their coupling to the Standard Model can be obtained using the method of nonlinear realizations of the spontaneously broken higher-dimensional space-time symmetries, and to an extent, are model independent. Phenomenological limits on these vector field parameters are obtained using LEP collider data and dark matter constraints

  14. Pitchcontrol of wind turbines using model free adaptivecontrol based on wind turbine code

    DEFF Research Database (Denmark)

    Zhang, Yunqian; Chen, Zhe; Cheng, Ming

    2011-01-01

    value is only based on I/O data of the wind turbine is identified and then the wind turbine system is replaced by a dynamic linear time-varying model. In order to verify the correctness and robustness of the proposed model free adaptive pitch controller, the wind turbine code FAST which can predict......As the wind turbine is a nonlinear high-order system, to achieve good pitch control performance, model free adaptive control (MFAC) approach which doesn't need the mathematical model of the wind turbine is adopted in the pitch control system in this paper. A pseudo gradient vector whose estimation...... the wind turbine loads and response in high accuracy is used. The results show that the controller produces good dynamic performance, good robustness and adaptability....

  15. Wind Generators

    Science.gov (United States)

    1989-01-01

    When Enerpro, Inc. president, Frank J. Bourbeau, attempted to file a patent on a system for synchronizing a wind generator to the electric utility grid, he discovered Marshall Space Flight Center's Frank Nola's power factor controller. Bourbeau advanced the technology and received a NASA license and a patent for his Auto Synchronous Controller (ASC). The ASC reduces generator "inrush current," which occurs when large generators are abruptly brought on line. It controls voltage so the generator is smoothly connected to the utility grid when it reaches its synchronous speed, protecting the components from inrush current damage. Generator efficiency is also increased in light winds by applying lower than rated voltage. Wind energy is utilized to drive turbines to generate electricity for utility companies.

  16. Wind turbine

    Science.gov (United States)

    Cheney, Jr., Marvin C.

    1982-01-01

    A wind turbine of the type having an airfoil blade (15) mounted on a flexible beam (20) and a pitch governor (55) which selectively, torsionally twists the flexible beam in response to wind turbine speed thereby setting blade pitch, is provided with a limiter (85) which restricts unwanted pitch change at operating speeds due to torsional creep of the flexible beam. The limiter allows twisting of the beam by the governor under excessive wind velocity conditions to orient the blades in stall pitch positions, thereby preventing overspeed operation of the turbine. In the preferred embodiment, the pitch governor comprises a pendulum (65,70) which responds to changing rotor speed by pivotal movement, the limiter comprising a resilient member (90) which engages an end of the pendulum to restrict further movement thereof, and in turn restrict beam creep and unwanted blade pitch misadjustment.

  17. Complex Polynomial Vector Fields

    DEFF Research Database (Denmark)

    The two branches of dynamical systems, continuous and discrete, correspond to the study of differential equations (vector fields) and iteration of mappings respectively. In holomorphic dynamics, the systems studied are restricted to those described by holomorphic (complex analytic) functions...... or meromorphic (allowing poles as singularities) functions. There already exists a well-developed theory for iterative holomorphic dynamical systems, and successful relations found between iteration theory and flows of vector fields have been one of the main motivations for the recent interest in holomorphic...... vector fields. Since the class of complex polynomial vector fields in the plane is natural to consider, it is remarkable that its study has only begun very recently. There are numerous fundamental questions that are still open, both in the general classification of these vector fields, the decomposition...

  18. Complex Polynomial Vector Fields

    DEFF Research Database (Denmark)

    Dias, Kealey

    vector fields. Since the class of complex polynomial vector fields in the plane is natural to consider, it is remarkable that its study has only begun very recently. There are numerous fundamental questions that are still open, both in the general classification of these vector fields, the decomposition...... of parameter spaces into structurally stable domains, and a description of the bifurcations. For this reason, the talk will focus on these questions for complex polynomial vector fields.......The two branches of dynamical systems, continuous and discrete, correspond to the study of differential equations (vector fields) and iteration of mappings respectively. In holomorphic dynamics, the systems studied are restricted to those described by holomorphic (complex analytic) functions...

  19. Where is 'place' in Aging in place?

    DEFF Research Database (Denmark)

    Blaakilde, Anne Leonora

    2015-01-01

    is influenced by universalism, aiming at equality in terms of access to health services and care. However, these welfare provisions seem to be deeply embedded in methodological nationalism, since only citizens with residence within the borders of Denmark have the right to live in public nursing homes or receive......The aim of this article is to contribute a transnational perspective to the field of environmental gerontology and the concept of aging in place. Seniors from the northern hemisphere, among them Danish citizens, are increasingly adapting to transnational lives as they move to warmer climates...... in-home help. It is argued that we should consider public solutions to the problems faced by frail Danish citizens in transnational settings, enhancing their opportunities to live abroad....

  20. Wind Velocity and Position Sensor-less Operation for PMSG Wind Generator

    Science.gov (United States)

    Senjyu, Tomonobu; Tamaki, Satoshi; Urasaki, Naomitsu; Uezato, Katsumi; Funabashi, Toshihisa; Fujita, Hideki

    Electric power generation using non-conventional sources is receiving considerable attention throughout the world. Wind energy is one of the available non-conventional energy sources. Electrical power generation using wind energy is possible in two ways, viz. constant speed operation and variable speed operation using power electronic converters. Variable speed power generation is attractive, because maximum electric power can be generated at all wind velocities. However, this system requires a rotor speed sensor, for vector control purpose, which increases the cost of the system. To alleviate the need of rotor speed sensor in vector control, we propose a new sensor-less control of PMSG (Permanent Magnet Synchronous Generator) based on the flux linkage. We can estimate the rotor position using the estimated flux linkage. We use a first-order lag compensator to obtain the flux linkage. Furthermore‚we estimate wind velocity and rotation speed using a observer. The effectiveness of the proposed method is demonstrated thorough simulation results.

  1. Broad patterns in domestic vector-borne Trypanosoma cruzi transmission dynamics: synanthropic animals and vector control.

    Science.gov (United States)

    Peterson, Jennifer K; Bartsch, Sarah M; Lee, Bruce Y; Dobson, Andrew P

    2015-10-22

    Chagas disease (caused by Trypanosoma cruzi) is the most important neglected tropical disease (NTD) in Latin America, infecting an estimated 5.7 million people in the 21 countries where it is endemic. It is one of the NTDs targeted for control and elimination by the 2020 London Declaration goals, with the first goal being to interrupt intra-domiciliary vector-borne T. cruzi transmission. A key question in domestic T. cruzi transmission is the role that synanthropic animals play in T. cruzi transmission to humans. Here, we ask, (1) do synanthropic animals need to be targeted in Chagas disease prevention policies?, and (2) how does the presence of animals affect the efficacy of vector control? We developed a simple mathematical model to simulate domestic vector-borne T. cruzi transmission and to specifically examine the interaction between the presence of synanthropic animals and effects of vector control. We used the model to explore how the interactions between triatomine bugs, humans and animals impact the number and proportion of T. cruzi-infected bugs and humans. We then examined how T. cruzi dynamics change when control measures targeting vector abundance are introduced into the system. We found that the presence of synanthropic animals slows the speed of T. cruzi transmission to humans, and increases the sensitivity of T. cruzi transmission dynamics to vector control measures at comparable triatomine carrying capacities. However, T. cruzi transmission is amplified when triatomine carrying capacity increases with the abundance of syntathoropic hosts. Our results suggest that in domestic T. cruzi transmission scenarios where no vector control measures are in place, a reduction in synanthropic animals may slow T. cruzi transmission to humans, but it would not completely eliminate transmission. To reach the 2020 goal of interrupting intra-domiciliary T. cruzi transmission, it is critical to target vector populations. Additionally, where vector control measures

  2. 78 FR 29364 - Exelon Corporation, Exelon Wind 1, LLC, Exelon Wind 2, LLC, Exelon Wind 3, LLC, Exelon Wind 4...

    Science.gov (United States)

    2013-05-20

    ...-005, QF07-55-005, QF07-56-005, QF07-257-004] Exelon Corporation, Exelon Wind 1, LLC, Exelon Wind 2, LLC, Exelon Wind 3, LLC, Exelon Wind 4, LLC, Exelon Wind 5, LLC, Exelon Wind 6, LLC, Exelon Wind 7, LLC, Exelon Wind 8, LLC, Exelon Wind 9, LLC, Exelon Wind 10, LLC, Exelon Wind 11, LLC, High Plains...

  3. Tuno Knob Offshore Wind Farm

    International Nuclear Information System (INIS)

    Madsen, P.S.

    1996-01-01

    In 1995 Midtkraft Power Company built Denmark's second offshore wind farm as a demonstration project. The project purpose is first of all to investigate the environmental aspects of offshore wind energy. The two primary objects are to study the impact on bird life and to test different methods for predicting the visual effect. The wind farm consists of 10 pitch-regulated Vestas V39 500 kW wind turbines placed on box caisson foundations in a shallow water area 6 km east of Jutland. The project has been implemented successfully under a very narrow time schedule, and during the first 6 months in operation, the production has been approx. 30% higher than expected. (author)

  4. Context in place

    DEFF Research Database (Denmark)

    Nordentoft, Helle Merete; Thomsen, Rie

    specifically argue for a more grounded approach to the conception of context - a topographic approach - in which the physical setting - i.e. 'the place' becomes an inevitable part of analyses of guidance practices in order to understand participants' sense-making processes. In the paper we draw on two case...... studies on interdisciplinary clinical supervision and work place guidance in which there appears to be a mismatch between intended outcomes and actual events. The analyses demonstrate and support that 'the place' seems - to influence partipants' responses in the guidance sessions and, therefore, must...

  5. Measuring tropospheric wind with microwave sounders

    Science.gov (United States)

    Lambrigtsen, B.; Su, H.; Turk, J.; Hristova-Veleva, S. M.; Dang, V. T.

    2017-12-01

    In its 2007 "Decadal Survey" of earth science missions for NASA the U.S. National Research Council recommended that a Doppler wind lidar be developed for a three-dimensional tropospheric winds mission ("3D-Winds"). The technology required for such a mission has not yet been developed, and it is expected that the next Decadal Survey, planned to be released by the end of 2017, will put additional emphasis on the still pressing need for wind measurements from space. The first Decadal Survey also called for a geostationary microwave sounder (GMS) on a Precipitation and All-weather Temperature and Humidity (PATH) mission, which could be used to measure wind from space. Such a sounder, the Geostationary Synthetic Thinned Aperture Radiometer (GeoSTAR), has been developed at the Jet Propulsion Laboratory (JPL). The PATH mission has not yet been funded by NASA, but a low-cost subset of PATH, GeoStorm has been proposed as a hosted payload on a commercial communications satellite. Both PATH and GeoStorm would obtain frequent (every 15 minutes of better) measurements of tropospheric water vapor profiles, and they can be used to derive atmospheric motion vector (AMV) wind profiles, even in the presence of clouds. Measurement of wind is particularly important in the tropics, where the atmosphere is largely not in thermal balance and wind estimates cannot generally be derived from temperature and pressure fields. We report on simulation studies of AMV wind vectors derived from a GMS and from a cluster of low-earth-orbiting (LEO) small satellites (e.g., CubeSats). The results of two separate simulation studies are very encouraging and show that a ±2 m/s wind speed precision is attainable, which would satisfy WMO requirements. A GMS observing system in particular, which can be implemented now, would enable significant progress in the study of atmospheric dynamics. Copyright 2017 California Institute of Technology. Government sponsorship acknowledged

  6. The Distributed Wind Cost Taxonomy

    Energy Technology Data Exchange (ETDEWEB)

    Forsyth, Trudy; Jimenez, Tony; Preus, Robert; Tegen, Suzanne; Baring-Gould, Ian

    2017-03-28

    To date, there has been no standard method or tool to analyze the installed and operational costs for distributed wind turbine systems. This report describes the development of a classification system, or taxonomy, for distributed wind turbine project costs. The taxonomy establishes a framework to help collect, sort, and compare distributed wind cost data that mirrors how the industry categorizes information. The taxonomy organizes costs so they can be aggregated from installers, developers, vendors, and other sources without losing cost details. Developing a peer-reviewed taxonomy is valuable to industry stakeholders because a common understanding the details of distributed wind turbine costs and balance of station costs is a first step to identifying potential high-value cost reduction opportunities. Addressing cost reduction potential can help increase distributed wind's competitiveness and propel the U.S. distributed wind industry forward. The taxonomy can also be used to perform cost comparisons between technologies and track trends for distributed wind industry costs in the future. As an initial application and piloting of the taxonomy, preliminary cost data were collected for projects of different sizes and from different regions across the contiguous United States. Following the methods described in this report, these data are placed into the established cost categories.

  7. Health impact of wind farms.

    Science.gov (United States)

    Kurpas, Donata; Mroczek, Bozena; Karakiewicz, Beata; Kassolik, Krzysztof; Andrzejewski, Waldemar

    2013-01-01

    analyses of these issues are justified, especially because none of the studies published in peer-reviewed journals so far meet the criteria for cohort or case-control studies. Due to methodology, currently available research results do not allow for higher than C-level recommendations. In the case of wind farms, the ideal types of research would be: a retrospective observation of a particular group of residents before and after the wind farm construction, case-control studies or cohort studies with control groups matched in respect of socioeconomic factors, predisposition for chronic diseases, exposure to environmental risk factors, and only one variable which would differentiate cases from controls--the distance between place of residence and a wind farm.

  8. Remote Sensing Wind and Wind Shear System.

    Science.gov (United States)

    Contents: Remote sensing of wind shear and the theory and development of acoustic doppler; Wind studies; A comparison of methods for the remote detection of winds in the airport environment; Acoustic doppler system development; System calibration; Airport operational tests.

  9. Vector Fields European user group meeting

    CERN Multimedia

    2007-01-01

    The "Vector Fields European user group meeting" will take place at CERN on 26 and 27 September 2007. Within this framework two workshops are organized at the CERN Training Centre: 24 September 2007
 Modelling Magnets with Opera 25 September 2007
Modelling of Charged Particle Beam Devices with Opera If you are interested in attending the workshop or the user group meeting please contact Julie Shepherd (Vector Fields) or Pierre Baehler (CERN) directly at: Julie.Shepherd@vectorfields.co.uk, +44 (0) 1865 854933 or +44 (0) 1865 370151 Pierre.Baehler@cern.ch, 75016 / 160156.

  10. Technical training - Places available

    CERN Document Server

    2012-01-01

    If you would like more information on a course, or for any other inquiry/suggestions, please contact Technical.Training@cern.ch Valeria Perez Reale, Learning Specialist, Technical Programme Coordinator (Tel.: 62424) Eva Stern and Elise Romero, Technical Training Administration (Tel.: 74924)   Electronics design Next Session Duration Language Availability Certified LabVIEW Associate Developer (CLAD) 06-Dec-12 to 06-Dec-12 1 hour English One more place available Compatibilité électromagnetique (CEM): Applications 23-Nov-12 to 23-Nov-12 3.5 hours English 3 places available Compatibilité électromagnétique (CEM): Introduction 23-Nov-12 to 23-Nov-12 3 hours English 43 places available Effets des Radiations sur les composants et systèmes électroniques 11-Dec-12 to 12-Dec-12 1 day 4 hours French 9 places available LabVIEW for beginners ...

  11. Planned place of birth

    DEFF Research Database (Denmark)

    Overgaard, Charlotte; Coxon, Kirstie; Stewart, Mary

    Title Planned place of birth: issues of choice, access and equity. Outline In Northern European countries, giving birth is generally safe for healthy women with uncomplicated pregnancies, and their babies. However, place of birth can affect women’s outcomes and experiences of birth. Whilst tertiary...... countries, maternity care is provided free to women, through public financing of health care; universal access to care is therefore secured. Nevertheless, different models of care exist, and debates about the appropriateness of providing maternity care in different settings take place in both countries...... in Denmark Coxon K et al: Planned place of birth in England: perceptions of accessing obstetric units, midwife led units and home birth amongst women and their partners. How these papers interrelate These papers draw upon recent research in maternity care, undertaken in Denmark and in England. In both...

  12. History, Criticism and Place

    DEFF Research Database (Denmark)

    Hinds, Mat; Carter, Adrian; Malpas, Jeff

    2012-01-01

    Rory Spence and Richard Leplastrier shared a conversation and friendship that lasted 20years until Spence's death in 2004. The discussions focused largely upon issues of place, distilled through the practice of Leplastrier....

  13. Marine Place Names

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains the geographic place names for features in the U.S territorial waters and outer continental shelf. These names can be used to find or define a...

  14. Fatigue reliability and effective turbulence models in wind farms

    DEFF Research Database (Denmark)

    Sørensen, John Dalsgaard; Frandsen, Sten Tronæs; Tarp-Johansen, N.J.

    2007-01-01

    behind wind turbines can imply a significant reduction in the fatigue lifetime of wind turbines placed in wakes. In this paper the design code model in the wind turbine code IEC 61400-1 (2005) is evaluated from a probabilistic point of view, including the importance of modeling the SN-curve by linear...

  15. Self-Placing Concrete

    OpenAIRE

    ECT Team, Purdue

    2007-01-01

    Certain concrete pours have areas where the congestion of reinforcing bars make placement of concrete almost impossible. Using conventional placing and vibration techniques, the resulting concrete can have considerable honeycombing due to the development of voids. Self-placing concrete is a possible solution to the problem. Also known as self-compactable concrete, self-consolidating concrete, flowable concrete, and non-vibration concrete. These concretes eliminate the need for vibration in a ...

  16. 'A Place to Sit'

    DEFF Research Database (Denmark)

    Hvejsel, Marie Frier; Klok, Julie Skovgaard; Bøhnke, Mia Marker

    Published in 2014 on the occasion of the third 'A Place to Sit' exhibition as a reflection upon three years of teaching tectonic method in architecture using the furniture scale as a learning basis.......Published in 2014 on the occasion of the third 'A Place to Sit' exhibition as a reflection upon three years of teaching tectonic method in architecture using the furniture scale as a learning basis....

  17. Technical training - Places available

    CERN Multimedia

    2012-01-01

    If you would like more information on a course, or for any other inquiry/suggestions, please contact Technical.Training@cern.ch Valeria Perez Reale, Learning Specialist, Technical Programme Coordinator (Tel.: 62424) Eva Stern and Elise Romero, Technical Training Administration (Tel.: 74924) HR Department Electronic Design Next Session Duration Language Availability Comprehensive VHDL for FPGA Design 08-Oct-12 to 12-Oct-12 5 days English 4 places Electrostatique / Protection ESD 28-Sep-12 to 28-Sep-12 3 hours French 25 places Impacts de la suppression du plomb (RoHS) en électronique 26-Oct-12 to 26-Oct-12 8 hours French 14 places Introduction to VHDL 10-Oct-12 to 11-Oct-12 2 days English 9 places LabVIEW Real Time and FPGA 13-Nov-12 to 16-Nov-12 5 days French 5 places LabVIEW for Experts 24-Sep-12 to 28-Sep-12 5 days English 6 places LabVIEW for beginners 15-Oct-12 to 17-...

  18. Wind energy

    International Nuclear Information System (INIS)

    Portilla S, L.A.

    1995-01-01

    The wind energy or eolic energy is a consequence of solar energy, the one which is absorbed by the atmosphere and is transformed into energy of movement of large bulks of air. In this process the atmosphere acts as the filter to the solar radiation and demotes the ultraviolet beams that result fatal to life in the Earth. The ionosphere is the most external cap and this is ionized by means of absorption process of ultraviolet radiation arising to the Sun. The atmosphere also acts as a trap to the infrared radiation, it that results from the continual process of energetic degradation. In this way, the interaction between Earth - Atmospheres, is behaved as a great greenhouse, maintaining the constant temperatures, including in the dark nights. Processes as the natural convection (that occur by the thermodynamic phenomenon), equatorial calmness, trade winds and against trade winds and global distribution of the air currents are described. The other hand, techniques as the transformation of the wind into energy and its parameters also are shown

  19. Wind power

    International Nuclear Information System (INIS)

    2006-06-01

    This road-map proposes by the Group Total aims to inform the public on the wind power. It presents the principles, the technology takes off, its applications and technology focus, the global market trends and the outlooks and Total commitments in the domain. (A.L.B.)

  20. Wind Energy Japan

    Energy Technology Data Exchange (ETDEWEB)

    Komatsubara, Kazuyo [Embassy of the Kingdom of the Netherlands, Tokyo (Japan)

    2012-06-15

    An overview is given of wind energy in Japan: Background; Wind Energy in Japan; Japanese Wind Energy Industry; Government Supports; Useful Links; Major Japanese Companies; Profiles of Major Japanese Companies; Major Wind Energy Projects in Japan.

  1. Wind energy systems

    Science.gov (United States)

    Stewart, H. J.

    1978-01-01

    A discussion on wind energy systems involved with the DOE wind energy program is presented. Some of the problems associated with wind energy systems are discussed. The cost, efficiency, and structural design of wind energy systems are analyzed.

  2. Fractal vector optical fields.

    Science.gov (United States)

    Pan, Yue; Gao, Xu-Zhen; Cai, Meng-Qiang; Zhang, Guan-Lin; Li, Yongnan; Tu, Chenghou; Wang, Hui-Tian

    2016-07-15

    We introduce the concept of a fractal, which provides an alternative approach for flexibly engineering the optical fields and their focal fields. We propose, design, and create a new family of optical fields-fractal vector optical fields, which build a bridge between the fractal and vector optical fields. The fractal vector optical fields have polarization states exhibiting fractal geometry, and may also involve the phase and/or amplitude simultaneously. The results reveal that the focal fields exhibit self-similarity, and the hierarchy of the fractal has the "weeding" role. The fractal can be used to engineer the focal field.

  3. Dissemination of wind technology

    Energy Technology Data Exchange (ETDEWEB)

    Wyatt, A

    1982-10-01

    This article argues that in order to adopt wind power in new places or in areas where windmills have not been used for many years, the following approaches should be used: 1) utilizing imported machines, 2) copy-production of the imported models, 3) production on a village level of local designs that are inexpensive, but which require more maintenance, or 4) production of local designs of moderate cost and high-reliability. Offers some national experiences in such developing countries as India, Argentina, and Cape Verde.

  4. Floating Foundations for Offshore Wind Turbines

    DEFF Research Database (Denmark)

    Andersen, Morten Thøtt

    The concept of harnessing the power of the wind dates all the way back to the first ships traversing the seas. Later, windmills enabled the use of wind power for industrial purposes. Since then, technology has allowed the production of clean renewable energy through the use of wind turbines....... These turbines have traditionally been placed on land, but several factors have urged a move to offshore locations. Now the boundaries are being pushed into deeper and deeper waters, where the idea of floating offshore wind turbines has emerged. In less than a decade, these have gone from scattered small...

  5. Global wind energy outlook 2006

    International Nuclear Information System (INIS)

    2006-09-01

    The global market for wind power has been expanding faster than any other source of renewable energy. From just 4,800 MW in 1995 the world total has multiplied more than twelve-fold to reach over 59,000 MW at the end of 2005. The international market is expected to have an annual turnover in 2006 of more than euro 13 billion, with an estimated 150,000 people employed around the world. The success of the industry has attracted investors from the mainstream finance and traditional energy sectors. In a number of countries the proportion of electricity generated by wind power is now challenging conventional fuels. The Global Wind Energy Outlook 2006 reports that over a third of the world's electricity - crucially including that required by industry - can realistically be supplied by wind energy by the middle of the century. The report provides an industry blueprint that explains how wind power could supply 34% of the world's electricity by 2050. Most importantly, it concludes that if wind turbine capacity implemented on this scale it would save 113 billion tonnes of CO2 from entering the atmosphere by 2050. This places wind power as one of the world's most important energy sources for the 21st century. The 'Global Wind Energy Outlook 2006' runs three different scenarios for wind power - a Reference scenario based on figures from the International Energy Agency (IEA); a Moderate version which assumes that current targets for renewable energy are successful; and an advanced version assuming that all policy options in favour of renewables have been adopted. These are then set against two scenarios for global energy demand. Under the Reference scenario, growth in demand is again based on IEA projections; under the High Energy Efficiency version, a range of energy efficiency measures result in a substantial reduction in demand

  6. Noncausal Bayesian Vector Autoregression

    DEFF Research Database (Denmark)

    Lanne, Markku; Luoto, Jani

    We propose a Bayesian inferential procedure for the noncausal vector autoregressive (VAR) model that is capable of capturing nonlinearities and incorporating effects of missing variables. In particular, we devise a fast and reliable posterior simulator that yields the predictive distribution...

  7. Understanding Vector Fields.

    Science.gov (United States)

    Curjel, C. R.

    1990-01-01

    Presented are activities that help students understand the idea of a vector field. Included are definitions, flow lines, tangential and normal components along curves, flux and work, field conservation, and differential equations. (KR)

  8. GAP Land Cover - Vector

    Data.gov (United States)

    Minnesota Department of Natural Resources — This vector dataset is a detailed (1-acre minimum), hierarchically organized vegetation cover map produced by computer classification of combined two-season pairs of...

  9. Sesquilinear uniform vector integral

    Indian Academy of Sciences (India)

    theory, together with his integral, dominate contemporary mathematics. ... directions belonging to Bartle and Dinculeanu (see [1], [6], [7] and [2]). ... in this manner, namely he integrated vector functions with respect to measures of bounded.

  10. Tagged Vector Contour (TVC)

    Data.gov (United States)

    Kansas Data Access and Support Center — The Kansas Tagged Vector Contour (TVC) dataset consists of digitized contours from the 7.5 minute topographic quadrangle maps. Coverage for the state is incomplete....

  11. Vector hysteresis models

    Czech Academy of Sciences Publication Activity Database

    Krejčí, Pavel

    1991-01-01

    Roč. 2, - (1991), s. 281-292 ISSN 0956-7925 Keywords : vector hysteresis operator * hysteresis potential * differential inequality Subject RIV: BA - General Mathematics http://www.math.cas.cz/~krejci/b15p.pdf

  12. Wind Loads on Structures

    DEFF Research Database (Denmark)

    Dyrbye, Claes; Hansen, Svend Ole

    Wind loads have to be taken into account when designing civil engineering structures. The wind load on structures can be systematised by means of the wind load chain: wind climate (global), terrain (wind at low height), aerodynamic response (wind load to pressure), mechanical response (wind...... pressure to structural response) and design criteria. Starting with an introduction of the wind load chain, the book moves on to meteorological considerations, atmospheric boundary layer, static wind load, dynamic wind load and scaling laws used in wind-tunnel tests. The dynamic wind load covers vibrations...... induced by wind turbulence, vortex shedding, flutter and galloping. The book gives a comprehensive treatment of wind effects on structures and it will be useful for consulting engineers designing wind-sensitive structures. It will also be valuable for students of civil engineering as textbook...

  13. Support vector machines applications

    CERN Document Server

    Guo, Guodong

    2014-01-01

    Support vector machines (SVM) have both a solid mathematical background and good performance in practical applications. This book focuses on the recent advances and applications of the SVM in different areas, such as image processing, medical practice, computer vision, pattern recognition, machine learning, applied statistics, business intelligence, and artificial intelligence. The aim of this book is to create a comprehensive source on support vector machine applications, especially some recent advances.

  14. Exotic composite vector boson

    International Nuclear Information System (INIS)

    Akama, K.; Hattori, T.; Yasue, M.

    1991-01-01

    An exotic composite vector boson V is introduced in two dynamical models of composite quarks, leptons, W, and Z. One is based on four-Fermi interactions, in which composite vector bosons are regarded as fermion-antifermion bound states and the other is based on the confining SU(2) L gauge model, in which they are given by scalar-antiscalar bound states. Both approaches describe the same effective interactions for the sector of composite quarks, leptons, W, Z, γ, and V

  15. Vector borne diseases

    OpenAIRE

    Melillo Fenech, Tanya

    2010-01-01

    A vector-borne disease is one in which the pathogenic microorganism is transmitted from an infected individual to another individual by an arthropod or other agent. The transmission depends upon the attributes and requirements of at least three different Iiving organisms : the pathologic agent which is either a virus, protozoa, bacteria or helminth (worm); the vector, which is commonly an arthropod such as ticks or mosquitoes; and the human host.

  16. (Re)tasting places

    DEFF Research Database (Denmark)

    Hedegaard, Liselotte

    2015-01-01

    What does geographical origin mean? It is an expression that associates food and wine with a specific place, an association embedded in the concept ‘terroir’ that refers to the complex interaction between a physical environment and local craftsmanship. It is a claim protected through labelling......-schemes and a claim that adds value to the place-related foods. However, viewing the connection between food and place as a question of proving a relationship or as a matter of protecting commercial claims does not seem to provide a satisfactory account for the status of geographically designated foods as being...... particularly attractive Central to the interest of this paper is to approach an understanding of geographical origin as a point of reference for taste. In terms of being sensory experience, taste is subjective. It is difficult to describe verbally and yet at the same time it is a trigger of the memory of past...

  17. Brand new authentic places

    DEFF Research Database (Denmark)

    Stender, Marie

    the relation and interplay between the two. This study strives to fill this gap by ethnographically tracing the process from design to occupancy including the role of branding as a means to create authenticity. The concept of authenticity is often associated with old houses and neighbourhoods, but also in new......How are places and material surroundings ascribed with meaning when new residential neighbourhoods are designed, branded and taken into use? Existing research on housing, neighbourhoods and urban design tends to take the perspective of either the architect or the user rather than to explore...... neighbourhoods stories of authenticity seems to be of great importance giving value and identity to place and people. By way of design and branding new places are implied with notions of the real, the original and the unique referring to e.g. its historical past, architectural uniqueness, sustainability or sense...

  18. Wind power and bird kills

    International Nuclear Information System (INIS)

    Raynolds, M.

    1998-01-01

    The accidental killing of birds by wind generators, and design improvements in the towers that support the turbines that might cut down on the bird killings were discussed. The first problem for the industry began in the late 1980s when the California Energy Commission reported as many as 160 birds (the majority being raptors, including the protected golden eagle) killed in one year in the vicinity of wind power plants. The key factor identified was the design of the towers as birds of prey are attracted to lattice towers as a place to hunt from. Tubular towers do not provide a place for the birds to perch, therefore they reduce the potential for bird strikes. Bird strikes also have been reported in Spain and the siting of the towers have been considered as the principal cause of the bird strikes. In view of these incidents, the wind power industry is developing standards for studying the potential of bird strikes and is continuing to study bird behaviour leading to collisions, the impact of topography, cumulative impacts and new techniques to reduce bird strikes. Despite the reported incidents, the risk of bird strikes by wind turbines, compared to other threats to birds such as pollution, oil spills, and other threats from fossil and nuclear fuels, is considered to be negligible. With continuing efforts to minimize incidents by proper design and siting, wind power can continue to grow as an environmentally sound and efficient source of energy

  19. Wind power and bird kills

    Energy Technology Data Exchange (ETDEWEB)

    Raynolds, M.

    1998-12-01

    The accidental killing of birds by wind generators, and design improvements in the towers that support the turbines that might cut down on the bird killings were discussed. The first problem for the industry began in the late 1980s when the California Energy Commission reported as many as 160 birds (the majority being raptors, including the protected golden eagle) killed in one year in the vicinity of wind power plants. The key factor identified was the design of the towers as birds of prey are attracted to lattice towers as a place to hunt from. Tubular towers do not provide a place for the birds to perch, therefore they reduce the potential for bird strikes. Bird strikes also have been reported in Spain and the siting of the towers have been considered as the principal cause of the bird strikes. In view of these incidents, the wind power industry is developing standards for studying the potential of bird strikes and is continuing to study bird behaviour leading to collisions, the impact of topography, cumulative impacts and new techniques to reduce bird strikes. Despite the reported incidents, the risk of bird strikes by wind turbines, compared to other threats to birds such as pollution, oil spills, and other threats from fossil and nuclear fuels, is considered to be negligible. With continuing efforts to minimize incidents by proper design and siting, wind power can continue to grow as an environmentally sound and efficient source of energy.

  20. Vector financial rogue waves

    International Nuclear Information System (INIS)

    Yan, Zhenya

    2011-01-01

    The coupled nonlinear volatility and option pricing model presented recently by Ivancevic is investigated, which generates a leverage effect, i.e., stock volatility is (negatively) correlated to stock returns, and can be regarded as a coupled nonlinear wave alternative of the Black–Scholes option pricing model. In this Letter, we analytically propose vector financial rogue waves of the coupled nonlinear volatility and option pricing model without an embedded w-learning. Moreover, we exhibit their dynamical behaviors for chosen different parameters. The vector financial rogue wave (rogon) solutions may be used to describe the possible physical mechanisms for the rogue wave phenomena and to further excite the possibility of relative researches and potential applications of vector rogue waves in the financial markets and other related fields. -- Highlights: ► We investigate the coupled nonlinear volatility and option pricing model. ► We analytically present vector financial rogue waves. ► The vector financial rogue waves may be used to describe the extreme events in financial markets. ► This results may excite the relative researches and potential applications of vector rogue waves.

  1. Stress at Work Place

    OpenAIRE

    Mohammad A. Shahrour

    2010-01-01

    One of hardest forms of stresses to avoid is that work place or job stress Job stress refers to stress experienced by an individual at or because of issues at their work place The term work related stress has many meanings and it causes different levels of anxiety. Not all challenges at work can be called stress as some of these challenges drive employees upward, and empower them to learn new skills or push them to work harder to achieve a certain goal. So, this type of challenges cannot be c...

  2. Ageing in communal place

    DEFF Research Database (Denmark)

    Aarhus, Rikke; Ballegaard, Stinne Aaløkke; Grönvall, Erik

    2009-01-01

    In this paper we adopt the position that design of social media for the elderly and virtual senior communities may be informed by studying `real´senior communities. Since current research efforts target the role of social media and virtual communities for supporting seniors ageing in place, i.......e. in their homes, housing communities seems a natural place to begin this enquiry. We conducted observations and informal interviews in six different senior dwellings. In this paper we present the key findings from these visits related to social interaction and the formation of communities and explicate how...

  3. CubeSat Constellation Cloud Winds(C3Winds) A New Wind Observing System to Study Mesoscale Cloud Dynamics and Processes

    Science.gov (United States)

    Wu, D. L.; Kelly, M.A.; Yee, J.-H.; Boldt, J.; Demajistre, R.; Reynolds, E. L.; Tripoli, G. J.; Oman, L. D.; Prive, N.; Heidinger, A. K.; hide

    2016-01-01

    The CubeSat Constellation Cloud Winds (C3Winds) is a NASA Earth Venture Instrument (EV-I) concept with the primary objective to better understand mesoscale dynamics and their structures in severe weather systems. With potential catastrophic damage and loss of life, strong extratropical and tropical cyclones (ETCs and TCs) have profound three-dimensional impacts on the atmospheric dynamic and thermodynamic structures, producing complex cloud precipitation patterns, strong low-level winds, extensive tropopause folds, and intense stratosphere-troposphere exchange. Employing a compact, stereo IR-visible imaging technique from two formation-flying CubeSats, C3Winds seeks to measure and map high-resolution (2 km) cloud motion vectors (CMVs) and cloud geometric height (CGH) accurately by tracking cloud features within 5-15 min. Complementary to lidar wind observations from space, the high-resolution wind fields from C3Winds will allow detailed investigations on strong low-level wind formation in an occluded ETC development, structural variations of TC inner-core rotation, and impacts of tropopause folding events on tropospheric ozone and air quality. Together with scatterometer ocean surface winds, C3Winds will provide a more comprehensive depiction of atmosphere-boundary-layer dynamics and interactive processes. Built upon mature imaging technologies and long history of stereoscopic remote sensing, C3Winds provides an innovative, cost-effective solution to global wind observations with potential of increased diurnal sampling via CubeSat constellation.

  4. Stellar winds

    International Nuclear Information System (INIS)

    Weymann, R.J.

    1978-01-01

    It is known that a steady outflow of material at comparable rates of mass loss but vastly different speeds is now known to be ubiquitous phenomenon among both the luminous hot stars and the luminous but cool red giants. The flows are probably massive enough in both cases to give rise to significant effects on stellar evolution and the mass balance between stars and the interstellar medium. The possible mechanisms for these phenomena as well as the methods of observation used are described. In particular, the mass-loss processes in stars other than the sun that also involve a steady flow of matter are considered. The evidence for their existence is described, and then the question of whether the process thought to produce the solar wind is also responsible for producing these stellar winds is explored

  5. Environmental management: a re-emerging vector control strategy.

    Science.gov (United States)

    Ault, S K

    1994-01-01

    Vector control may be accomplished by environmental management (EM), which consists of permanent or long-term modification of the environment, temporary or seasonal manipulation of the environment, and modifying or changing our life styles and practices to reduce human contact with infective vectors. The primary focus of this paper is EM in the control of human malaria, filariasis, arboviruses, Chagas' disease, and schistosomiasis. Modern EM developed as a discipline based primarily in ecologic principles and lessons learned from the adverse environmental impacts of rural development projects. Strategies such as the suppression of vector populations through the provision of safe water supplies, proper sanitation, solid waste management facilities, sewerage and excreta disposal systems, water manipulation in dams and irrigation systems, vector diversion by zooprophylaxis, and vector exclusion by improved housing, are discussed with appropriate examples. Vectors of malaria, filariasis, Chagas' disease, and schistosomiasis have been controlled by drainage or filling aquatic breeding sites, improved housing and sanitation, the use of expanded polystyrene beads, zooprophylaxis, or the provision of household water supplies. Community participation has been effective in the suppression of dengue vectors in Mexico and the Dominican Republic. Alone or combined with other vector control methods, EM has been proven to be a successful approach to vector control in a number of places. The future of EM in vector control looks promising.

  6. Open and partially closed models of the solar wind interaction with outer planet magnetospheres. The case of Saturn

    Energy Technology Data Exchange (ETDEWEB)

    Belenkaya, Elena S.; Alexeev, Igor I.; Kalegaev, Vladimir V.; Pensionerov, Ivan A.; Blokhina, Marina S.; Parunakian, David A. [Federal State Budget Educational Institution of Higher Education M.V. Lomonosov Moscow State Univ., Moscow (Russian Federation). Skobeltsyn Inst. of Nuclear Physics (SINP MSU); Cowley, Stanley W. H. [Leicester Univ. (United Kingdom). Dept. of Physics and Astronomy

    2017-07-01

    A wide variety of interactions take place between the magnetized solar wind plasma outflow from the Sun and celestial bodies within the solar system. Magnetized planets form magnetospheres in the solar wind, with the planetary field creating an obstacle in the flow. The reconnection efficiency of the solar-wind-magnetized planet interaction depends on the conditions in the magnetized plasma flow passing the planet. When the reconnection efficiency is very low, the interplanetary magnetic field (IMF) does not penetrate the magnetosphere, a condition that has been widely discussed in the recent literature for the case of Saturn. In the present paper, we study this issue for Saturn using Cassini magnetometer data, images of Saturn's ultraviolet aurora obtained by the HST, and the paraboloid model of Saturn's magnetospheric magnetic field. Two models are considered: first, an open model in which the IMF penetrates the magnetosphere, and second, a partially closed model in which field lines from the ionosphere go to the distant tail and interact with the solar wind at its end. We conclude that the open model is preferable, which is more obvious for southward IMF. For northward IMF, the model calculations do not allow us to reach definite conclusions. However, analysis of the observations available in the literature provides evidence in favor of the open model in this case too. The difference in magnetospheric structure for these two IMF orientations is due to the fact that the reconnection topology and location depend on the relative orientation of the IMF vector and the planetary dipole magnetic moment. When these vectors are parallel, two-dimensional reconnection occurs at the low-latitude neutral line. When they are antiparallel, three-dimensional reconnection takes place in the cusp regions. Different magnetospheric topologies determine different mapping of the open-closed boundary in the ionosphere, which can be considered as a proxy for the poleward edge

  7. NORSEWInD satellite wind climatology

    DEFF Research Database (Denmark)

    Hasager, Charlotte Bay; Badger, Merete; Mouche, Alexis

    The EU-NORSEWInD project www.norsewind.eu has taken place from August 2008 to July 2012 (4 years). NORSEWInD is short for Northern Seas Wind Index database. In the project ocean surface wind observations from space have been retrieved, processed and analysed. The overall aim of the work...... is to provide new offshore wind climatology map for the entire area of interest based on satellite remote sensing. This has been based on Synthetic Aperture Radar (SAR) from Envisat ASAR using 9000 scenes re-processed with ECMWF wind direction and CMOD-IFR. The number of overlapping samples range from 450...... in the Irish Sea to more than 1200 in most of the Baltic Sea. Wind resource statistics include maps at 2 km spatial resolution of mean wind speed, Weibull A and k, and energy density at 10 m above sea level. Uncertainty estimates on the number of available samples for each of the four parameters are presented...

  8. High Voltage Power Transmission for Wind Energy

    Science.gov (United States)

    Kim, Young il

    The high wind speeds and wide available area at sea have recently increased the interests on offshore wind farms in the U.S.A. As offshore wind farms become larger and are placed further from the shore, the power transmission to the onshore grid becomes a key feature. Power transmission of the offshore wind farm, in which good wind conditions and a larger installation area than an onshore site are available, requires the use of submarine cable systems. Therefore, an underground power cable system requires unique design and installation challenges not found in the overhead power cable environment. This paper presents analysis about the benefit and drawbacks of three different transmission solutions: HVAC, LCC/VSC HVDC in the grid connecting offshore wind farms and also analyzed the electrical characteristics of underground cables. In particular, loss of HV (High Voltage) subsea power of the transmission cables was evaluated by the Brakelmann's theory, taking into account the distributions of current and temperature.

  9. Danish offshore wind - Key environmental issues

    International Nuclear Information System (INIS)

    2006-11-01

    Danish experience from the past 15 years shows that offshore wind farms, if placed right, can be engineered and operated without significant damage to the marine environment and vulnerable species. The comprehensive environmental monitoring programmes of Horns Rev Offshore Wind Farm and Nysted Offshore Wind Farm confirm that, under the rieght conditions, even big wind farms pose low risk to birds, mammals and fish, even though there will be changes in the living conditions of some species by an increase in habitat heterogeneity. The monitoring also shows that appropriate siting of offshore wind farms is an essential precondition for ensuring limited impact on nature and the environment, and that careful spatial planning is necessary to avoid damaging cumulative impacts. Due consideration to limiting the impacts on nature together with positive attitudes towards offshore wind farms in local communities and challenging energy policy objectives at national and international levels mean that prospects look bright for future offshore expansion. (au)

  10. Probabilistic Modeling of Wind Turbine Drivetrain Components

    DEFF Research Database (Denmark)

    Rafsanjani, Hesam Mirzaei

    Wind energy is one of several energy sources in the world and a rapidly growing industry in the energy sector. When placed in offshore or onshore locations, wind turbines are exposed to wave excitations, highly dynamic wind loads and/or the wakes from other wind turbines. Therefore, most components...... in a wind turbine experience highly dynamic and time-varying loads. These components may fail due to wear or fatigue, and this can lead to unplanned shutdown repairs that are very costly. The design by deterministic methods using safety factors is generally unable to account for the many uncertainties. Thus......, a reliability assessment should be based on probabilistic methods where stochastic modeling of failures is performed. This thesis focuses on probabilistic models and the stochastic modeling of the fatigue life of the wind turbine drivetrain. Hence, two approaches are considered for stochastic modeling...

  11. Mini-review of wind energy 1995

    International Nuclear Information System (INIS)

    1996-01-01

    At the 1995 meeting of the International Energy Agency CADDET renewable energy technologies programme, contributors aimed to advise on wind energy use and identify future needs for analysis of future trends and review research tasks. Three major trends leading to the commercial exploitation of wind energy are identified. Firstly, cost reduction and increased efficiency is aimed at through technical innovation, economies of scale and reduced labour costs. The environmental and social benefits of wind energy are acknowledged in the second place. Lastly, wind turbine deployment has been given decisive market incentives. Two major barriers block the development of the wind energy market, availability of site locations and the current economic state of countries likely to espouse wind energy. (UK)

  12. Wind conditions for wind turbine design

    Energy Technology Data Exchange (ETDEWEB)

    Maribo Pedersen, B.

    1999-04-01

    Delegates from Europe and USA attended the meeting and discussed general aspects of wind conditions for wind turbine design. The subjects and the presented papers covered a very broad range of aspects of wind conditions and related influence on the wind turbine. (EHS)

  13. Technical training - Places available

    CERN Multimedia

    Davide Vitè

    2006-01-01

    Places available as of 16.5.2006 (May-November course sessions) Technical Training: Places available The number of places available may vary. Please check our Web site to find out the current availability. Places are available on the following courses: Title Hours Date Language ACROBAT 7.0 : Utilisation de fichiers PDF 8 8.05.06 F WORD 2003 - niveau 2 : ECDL 16 22-23.05.06 23-24.05.06 F Comprehensive VHDL for FPGA Design 40 29.05-2.06.06 E C++ Programming Part 2 - Advanced C++ and its Traps and Pitfalls 32 30.05-2.06.06 E ACROBAT 7.0 : Utilisation de fichiers PDF 24 7-9.06.06 E AutoCAD Mechanical 2006 16 13-14.06.06 F CERN EDMS for Local Administrators 16 13-14.06.06 E LabVIEW Base 2 32 27.06-5.07.06 F C++ Programming Part 3 - Templates and the STL (Standard Template Library) 16 27-28.06.06 E C++ Programming Part 4 - Exceptions 8 29.06.06 E FrontPage 2003 - niveau 1 16 29-...

  14. The Value of Place

    Science.gov (United States)

    Dentzau, Michael W.

    2014-01-01

    This commentary seeks to expand the dialogue on place-based science education presented in Katie Lynn Brkich's article, where the connections fifth grade students make between their formal earth science curriculum and their lived experiences are highlighted. The disconnect between the curriculum the students are offered and their immediate…

  15. The power of place.

    Science.gov (United States)

    Lock, Lin R; Gibb, Heather J

    2003-06-01

    to describe the power that 'place' holds over the postnatal-care experiences of women. a study informed by phenomenology within a feminist framework was undertaken to examine the experiences of women electing early postnatal discharge. Three extended conversations with each woman participating in the study were audiotaped and transcribed. Journal notes made by the researcher added to the audiotaped data. Thematic analysis revealed major structures of experience. data were obtained from conversations with women in their respective homes. five women, parity 1-3, living in the Sydney metropolitan area and birthing in their local hospitals participated in the study. four major constructs of experience were revealed through analysis and include spatiality, corporeality, temporality and relationality. In this paper, components of spatiality expressed through the power place exerts in matters of physical environment,control, confidence, safety, time, talk and the heart of the matter are presented. the experiences of women entering the foreign place of hospital to birth their children were those of alienation and disempowerment while the familiar territory of home offered stronger feelings of security and support. failing to recognise the impact of place on the experiences of postnatal women reduces the likelihood that midwives will be able to offer sensitive and appropriate care.

  16. Ageing in Communal Place

    DEFF Research Database (Denmark)

    Aarhus, Rikke; Ballegaard, Stinne Aaløkke; Grönvall, Erik

    2009-01-01

    In this paper we adopt the position that design of social media for the elderly and virtual senior communities may be informed by studying ‘real’ senior communities. Since current research efforts target the role of social media and virtual communities for supporting seniors ageing in place, i...

  17. Technical training - Places available

    CERN Multimedia

    2003-01-01

    * Etant donné le délai d'impression du Bulletin, ces places peuvent ne plus être disponibles au moment de sa parution. Veuillez consulter notre site Web pour avoir la dernière mise à jour. ** The number of places available may vary. Please check our Web site to find out the current availability. Des places sont disponibles dans les cours suivants : Places are available in the following courses: Hands-on Introduction to Python Programming 12 – 14.11.03 (3 days) ACCESS 2000 – niveau 1 13 & 14.11.03 (2 jours) C++ for Particle Physicists 17 – 21.11.03 (6 x 3-hour lectures) Programmation automate Schneider TSX Premium – niveau 2  18 – 21.11.03 (4 jours) Planification de projet avec MS-Project/Project Planning with MS-Project (gratuit/free of charge – langue à définir/language to be defined) : 18 & 25.11.03 (2 jours/2 days) JAVA 2 Enterprise Edition – Part 1 : WEB...

  18. Analysis of Renewable Energy Policies Related to Repowering the Wind Energy Sector: the Spanish Case

    OpenAIRE

    Rodriguez, Roberto; Rodríguez Monroy, Carlos; Rodriguez, Rubén; Calvo Narvaez, Felix

    2013-01-01

    In countries that started early with wind energy, the old wind turbines were located in places where the wind is often very good. Since the best places in which the wind is concerned are occupied by old wind turbines (with lower capacity than the more recent ones) the trend is to start replacing old turbines with new ones. With repowering, the first generation of wind turbines can be replaced by modern multi-megawatt wind turbines. The aim of this article is to analyze energy policies in ...

  19. Multi-perspective views of students’ difficulties with one-dimensional vector and two-dimensional vector

    Science.gov (United States)

    Fauzi, Ahmad; Ratna Kawuri, Kunthi; Pratiwi, Retno

    2017-01-01

    Researchers of students’ conceptual change usually collects data from written tests and interviews. Moreover, reports of conceptual change often simply refer to changes in concepts, such as on a test, without any identification of the learning processes that have taken place. Research has shown that students have difficulties with vectors in university introductory physics courses and high school physics courses. In this study, we intended to explore students’ understanding of one-dimensional and two-dimensional vector in multi perspective views. In this research, we explore students’ understanding through test perspective and interviews perspective. Our research study adopted the mixed-methodology design. The participants of this research were sixty students of third semester of physics education department. The data of this research were collected by testand interviews. In this study, we divided the students’ understanding of one-dimensional vector and two-dimensional vector in two categories, namely vector skills of the addition of one-dimensionaland two-dimensional vector and the relation between vector skills and conceptual understanding. From the investigation, only 44% of students provided correct answer for vector skills of the addition of one-dimensional and two-dimensional vector and only 27% students provided correct answer for the relation between vector skills and conceptual understanding.

  20. X-band COSMO-SkyMed wind field retrieval, with application to coastal circulation modeling

    Directory of Open Access Journals (Sweden)

    A. Montuori

    2013-02-01

    Full Text Available In this paper, X-band COSMO-SkyMed© synthetic aperture radar (SAR wind field retrieval is investigated, and the obtained data are used to force a coastal ocean circulation model. The SAR data set consists of 60 X-band Level 1B Multi-Look Ground Detected ScanSAR Huge Region COSMO-SkyMed© SAR data, gathered in the southern Tyrrhenian Sea during the summer and winter seasons of 2010. The SAR-based wind vector field estimation is accomplished by resolving both the SAR-based wind speed and wind direction retrieval problems independently. The sea surface wind speed is retrieved by means of a SAR wind speed algorithm based on the azimuth cut-off procedure, while the sea surface wind direction is provided by means of a SAR wind direction algorithm based on the discrete wavelet transform multi-resolution analysis. The obtained wind fields are compared with ground truth data provided by both ASCAT scatterometer and ECMWF model wind fields. SAR-derived wind vector fields and ECMWF model wind data are used to construct a blended wind product regularly sampled in both space and time, which is then used to force a coastal circulation model of a southern Tyrrhenian coastal area to simulate wind-driven circulation processes. The modeling results show that X-band COSMO-SkyMed© SAR data can be valuable in providing effective wind fields for coastal circulation modeling.

  1. Vectorization of nuclear codes for atmospheric transport and exposure calculation of radioactive materials

    International Nuclear Information System (INIS)

    Asai, Kiyoshi; Shinozawa, Naohisa; Ishikawa, Hirohiko; Chino, Masamichi; Hayashi, Takashi

    1983-02-01

    Three computer codes MATHEW, ADPIC of LLNL and GAMPUL of JAERI for prediction of wind field, concentration and external exposure rate of airborne radioactive materials are vectorized and the results are presented. Using the continuous equation of incompressible flow as a constraint, the MATHEW calculates the three dimensional wind field by a variational method. Using the particle-in -cell method, the ADPIC calculates the advection and diffusion of radioactive materials in three dimensional wind field and terrain, and gives the concentration of the materials in each cell of the domain. The GAMPUL calculates the external exposure rate assuming Gaussian plume type distribution of concentration. The vectorized code MATHEW attained 7.8 times speedup by a vector processor FACOM230-75 APU. The ADPIC and GAMPUL are estimated to attain 1.5 and 4 times speedup respectively on CRAY-1 type vector processor. (author)

  2. Malaria vector species in Colombia: a review

    Directory of Open Access Journals (Sweden)

    James Montoya-Lerma

    2011-08-01

    Full Text Available Here we present a comprehensive review of the literature on the vectorial importance of the major Anopheles malaria vectors in Colombia. We provide basic information on the geographical distribution, altitudinal range, immature habitats, adult behaviour, feeding preferences and anthropophily, endophily and infectivity rates. We additionally review information on the life cycle, longevity and population fluctuation of Colombian Anopheles species. Emphasis was placed on the primary vectors that have been epidemiologically incriminated in malaria transmission: Anopheles darlingi, Anopheles albimanus and Anopheles nuneztovari. The role of a selection of local, regional or secondary vectors (e.g., Anopheles pseudopunctipennis and Anopheles neivai is also discussed. We highlight the importance of combining biological, morphological and molecular data for the correct taxonomical determination of a given species, particularly for members of the species complexes. We likewise emphasise the importance of studying the bionomics of primary and secondary vectors along with an examination of the local conditions affecting the transmission of malaria. The presence and spread of the major vectors and the emergence of secondary species capable of transmitting human Plasmodia are of great interest. When selecting control measures, the anopheline diversity in the region must be considered. Variation in macroclimate conditions over a species' geographical range must be well understood and targeted to plan effective control measures based on the population dynamics of the local Anopheles species.

  3. Spatio-temporal data analytics for wind energy integration

    CERN Document Server

    Yang, Lei; Zhang, Junshan

    2014-01-01

    This SpringerBrief presents spatio-temporal data analytics for wind energy integration using stochastic modeling and optimization methods. It explores techniques for efficiently integrating renewable energy generation into bulk power grids. The operational challenges of wind, and its variability are carefully examined. A spatio-temporal analysis approach enables the authors to develop Markov-chain-based short-term forecasts of wind farm power generation. To deal with the wind ramp dynamics, a support vector machine enhanced Markov model is introduced. The stochastic optimization of economic di

  4. Wind Farm Wake: The Horns Rev Photo Case

    DEFF Research Database (Denmark)

    Hasager, Charlotte Bay; Rasmussen, Leif; Peña, Alfredo

    2013-01-01

    The aim of the paper is to examine the nowadays well-known wind farm wake photographs taken on 12 February 2008 at the offshore Horns Rev 1 wind farm. The meteorological conditions are described from observations from several satellite sensors quantifying clouds, surface wind vectors and sea surf...... in the wake regions with relatively high axial velocities and high turbulent kinetic energy. The wind speed is near cut-in and most turbines produce very little power. The rotational pattern of spiraling bands produces the large-scale structure of the wake fog....

  5. Vectorization in quantum chemistry

    International Nuclear Information System (INIS)

    Saunders, V.R.

    1987-01-01

    It is argued that the optimal vectorization algorithm for many steps (and sub-steps) in a typical ab initio calculation of molecular electronic structure is quite strongly dependent on the target vector machine. Details such as the availability (or lack) of a given vector construct in the hardware, vector startup times and asymptotic rates must all be considered when selecting the optimal algorithm. Illustrations are drawn from: gaussian integral evaluation, fock matrix construction, 4-index transformation of molecular integrals, direct-CI methods, the matrix multiply operation. A cross comparison of practical implementations on the CDC Cyber 205, the Cray-IS and Cray-XMP machines is presented. To achieve portability while remaining optimal on a wide range of machines it is necessary to code all available algorithms in a machine independent manner, and to select the appropriate algorithm using a procedure which is based on machine dependent parameters. Most such parameters concern the timing of certain vector loop kernals, which can usually be derived from a 'bench-marking' routine executed prior to the calculation proper

  6. Parks, People and Places

    DEFF Research Database (Denmark)

    Molin, Julie Frøik

    This thesis suggests, by applying a ‘place’ perspective, that involving users in operational management of green spaces holds potentials for enhancing ‘place attachment’ of urban inhabitants. As this can also build their commitment to decision making on their local living environment, green space...... maintenance becomes a potentially important setting for governance processes. Through a number of qualitative case studies, based on semi-structured interviews with municipal and community actors in Denmark and England, this dissertation explores the status and potentials of applying a place-based governance...... approach to green space maintenance. To guide the exploration a theoretical framework was developed inductively, structured around concepts of environmental governance in combination with strategic approaches to green space management. The framework is operationalised by analyses of the governance...

  7. Technical Training: Places available

    CERN Multimedia

    Monique Duval

    2004-01-01

    If you wish to participate in one of the following courses, please discuss with your supervisor and apply electronically directly from the course description pages that can be found on the Web at: http://www.cern.ch/Training/ or fill in an 'application for training' form available from your Divisional Secretariat or from your DTO (Divisional Training Officer). Applications will be accepted in the order of their receipt. The number of places available may vary. Please check our Web site to find out the current availability. Places are available in the following courses: The Joint PVSS JCOP Framework: 14 - 18.6.2004 (5 days) EXCEL 2003 - niveau 2 : 17 & 18.6.2004 (2 jours) MAGNE-04 : Magnétisme pour l'électrotechnique : 6 au 8.7.2004 (3 jours) Technical Training Monique Duval - Tel.74924 technical.training@cern.ch

  8. A New Fault Diagnosis Algorithm for PMSG Wind Turbine Power Converters under Variable Wind Speed Conditions

    Directory of Open Access Journals (Sweden)

    Yingning Qiu

    2016-07-01

    Full Text Available Although Permanent Magnet Synchronous Generator (PMSG wind turbines (WTs mitigate gearbox impacts, they requires high reliability of generators and converters. Statistical analysis shows that the failure rate of direct-drive PMSG wind turbines’ generators and inverters are high. Intelligent fault diagnosis algorithms to detect inverters faults is a premise for the condition monitoring system aimed at improving wind turbines’ reliability and availability. The influences of random wind speed and diversified control strategies lead to challenges for developing intelligent fault diagnosis algorithms for converters. This paper studies open-circuit fault features of wind turbine converters in variable wind speed situations through systematic simulation and experiment. A new fault diagnosis algorithm named Wind Speed Based Normalized Current Trajectory is proposed and used to accurately detect and locate faulted IGBT in the circuit arms. It is compared to direct current monitoring and current vector trajectory pattern approaches. The results show that the proposed method has advantages in the accuracy of fault diagnosis and has superior anti-noise capability in variable wind speed situations. The impact of the control strategy is also identified. Experimental results demonstrate its applicability on practical WT condition monitoring system which is used to improve wind turbine reliability and reduce their maintenance cost.

  9. Technical Training: Places available

    CERN Multimedia

    Davide Vitè

    2006-01-01

    Places available as of 30.5.2006 (June-November course sessions) The number of places available may vary. Please check our Web site to find out the current availability. Places are available on the following courses: Titre Heure Date Langue ACROBAT 7.0 : Utilisation de fichiers PDF 8 6.06.06 F Introduction à InDesign 16 7-8.06.06 F Python: Hands-on Introduction 24 7-9.06.06 E LabVIEW Base 2 16 22-23.06.06 F FileMaker - niveau 1 16 26-27.06.06 F C++ Programming Part 3 - Templates and the STL (Standard Template Library) 16 27-28.06.06 E C++ Programming Part 4 - Exceptions 8 29.06.06 E FrontPage 2003 - niveau 1 16 29-30.06.06 F Manipulation des images 4 6.07.06 F Introduction to Databases and Database Design 16 11-12.07.06 E ACCESS 2003 - Level 1: ECDL 16 13-14.07.06 E-F Design Patterns 16 25-26.07.06 E Introduction à Dreamweaver MX 16 ...

  10. Technical training: Places available

    CERN Multimedia

    Davide Vitè

    2006-01-01

    Places available as of 13.6.2006 (June-December course sessions) The number of places available may vary. Please check our Web site to find out the current availability. Places are available on the following courses: Titre Heure Date Langue LabVIEW Base 2 16 22-23.06.06 F FileMaker - niveau 1 16 26-27.06.06 F C++ Programming Part 3 - Templates and the STL (Standard Template Library) 16 27-28.06.06 E C++ Programming Part 4 - Exceptions 8 29.06.06 E FrontPage 2003 - niveau 1 16 29-30.06.06 F Manipulation des images 4 6.07.06 F Introduction to Databases and Database Design 16 11-12.07.06 E ACCESS 2003 - Level 1: ECDL 16 13-14.07.06 E-F Design Patterns 16 25-26.07.06 E Introduction à Dreamweaver MX 16 26-27.07.06 F ANSYS DesignModeler 16 29-30.08.06 F LabVIEW Basics 1 24 4-6.09.06 E ANSYS Workbench 32 12-15.09.06 F AutoCAD Mechanical 20...

  11. Technical Training: Places available

    CERN Multimedia

    Davide Vitè

    2006-01-01

    Places available as of 9.5.2006 (May-October course sessions) The number of places available may vary. Please check our Web site to find out the current availability. Places are available on the following courses: find out the curren Hours Date Language LabVIEW Application Development 24 15-17.05.06 E LabVIEW Advanced Programming 16 18-19.05.06 E PERL 5: Advanced Aspects 8 18.05.06 E Technique du vide 16 18-19.05.06 F FileMaker - niveau 2 16 11-12.05.06 F WORD 2003 - niveau 2 : ECDL 16 22-23.05.06 F Introduction au VHDL et utilisation du simulateur NCVHDL de CADENCE 16 23-24.05.06 F Comprehensive VHDL for FPGA Design 40 29.05-2.06.06 E C++ Programming Part 2 - Advanced C++ and its Traps and Pitfalls 32 30.05-2.06.06 E Python: Hands-on Introduction 24 7-9.06.06 E AutoCAD Mechanical 2006 16 13-14.06.06 F CERN EDMS for Local Administrators 16 13-14.06.06...

  12. Technical Training: Places available

    CERN Multimedia

    Davide Vitè

    2006-01-01

    Places available as of 27.6.2006 (July-December course sessions) The number of places available may vary. Please check our Web site to find out the current availability. Places are available on the following courses: Titre Heure Date Langue Manipulation des images 4 6.07.06 F Introduction to Databases and Database Design 16 11-12.07.06 E ACCESS 2003 - Level 1: ECDL 16 13-14.07.06 E-F Design Patterns 16 25-26.07.06 E CERN EDMS for Local Administrators 16 1-2.08.06 E ANSYS DesignModeler 16 29-30.08.06 F CERN EDMS - Introduction 8 5.09.06 E CERN EDMS MTF en pratique 4 6.09.06 F LabVIEW Basics 1 24 4-6.09.06 E ANSYS Workbench 32 12-15.09.06 F AutoCAD Mechanical 2006 16 12-13.09.06 F CERN EDMS for Engineers 8 12.09.06 E Software Engineering in the Small and the Large 16 12-13.09.06 E AutoCAD 2006 - niveau 1 32 14-21.09.06 F LabVIEW Basics 2 ...

  13. Technical Training: Places available

    CERN Multimedia

    Davide Vitè

    2006-01-01

    Places available as of 11.7.2006 (July-December course sessions) The number of places available may vary. Please check our Web site to find out the current availability. Places are available on the following courses: Titre Heure Date Langue Design Patterns 16 25-26.07.06 E CERN EDMS for Local Administrators 16 1-2.08.06 E ANSYS DesignModeler 16 29-30.08.06 F CERN EDMS – Introduction 8 5.09.06 E CERN EDMS MTF en pratique 4 6.09.06 F LabVIEW Basics 1 24 4-6.09.06 E ANSYS Workbench 32 12-15.09.06 F AutoCAD Mechanical 2006 16 12-13.09.06 F CERN EDMS for Engineers 8 12.09.06 E Software Engineering in the Small and the Large 16 12-13.09.06 E LabVIEW Basics 2 16 14-15.09.06 E LabVIEW: Working efficiently with LabWIEW 8 8 18.09.06 E PCAD Schémas ? Introduction 16 21-22.09.06 F PCAD PCB - Introduction  24 27-29.09.06 F C++ for Particle Physicists ...

  14. Technical Training: Places available

    CERN Multimedia

    2006-01-01

    Places available as of 21.3.2006 (March-October course sessions) The number of places available may vary. Please check our Web site to find out the current availability. Places are available on the following courses: find out the curren Hours Date Language ACROBAT 7.0 : Utilisation de fichiers PDF 8 8.05.06 F Project Planning with MS-Project 16 9.05-6.06.06 E STEP7: niveau 1 32 9-12.05.06 E-F Oracle: Programming with PL/SQL 24 10-12.05.06 E FileMaker - niveau 2 16 11-12.05.06 F LabVIEW Application Development 24 15-17.05.06 E LabVIEW Advanced Programming 16 18-19.05.06 E PERL 5: Advanced Aspects 8 18.05.06 E Technique du vide 16 18-19.05.06 F WORD 2003 - niveau 2 : ECDL 16 22-23.05.06 F Introduction au VHDL et utilisation du simulateur NCVHDL de CADENCE 16 23-24.05.06 F Comprehensive VHDL for FPGA Design 40 29.05-2.06.06 E C++ Programming Part 2 - Advanced C++ and its T...

  15. Technical Training: Places available

    CERN Multimedia

    Davide Vitè

    2006-01-01

    Places available as of 19.7.2006 (August-December course sessions) The number of places available may vary. Please check our Web site to find out the current availability. Places are available on the following courses: Titre Heure Date Langue CERN EDMS for Local Administrators 16 1-2.08.06 E ANSYS DesignModeler 16 29-30.08.06 F OUTLOOK 2003 (Short Course I) - E-mail 3 1.09.06 E/F OUTLOOK 2003 (Short Course II) - Calendar, Tasks and Notes 3 1.09.06 E/F CERN EDMS - Introduction 8 5.09.06 E CERN EDMS MTF en pratique 4 6.09.06 F LabVIEW Basics 1 24 11-13.09.06 E ANSYS Workbench 32 12-15.09.06 F CERN EDMS for Engineers 8 12.09.06 E Software Engineering in the Small and the Large 16 12-13.09.06 E LabVIEW Basics 2 16 14-15.09.06 E EXCEL 2003 (Short Course I) - HowTo... Work with formulae 3 15.09.06 E/F WORD 2003 (Short Course III) - HowTo... Work with long docu...

  16. Technical Training: Places available

    CERN Multimedia

    DAvide Vitè

    2006-01-01

    Places available as of 25.7.2006 (August-December course sessions) The number of places available may vary. Please check our Web site to find out the current availability. Places are available on the following courses: Titre Heure Date Langue CERN EDMS for Local Administrators 16 1-2.08.06 E ANSYS DesignModeler 16 29-30.08.06 F EXCEL 2003 - niveau 1 : ECDL 16 30-31.08.06 F OUTLOOK 2003 (Short Course I) - E-mail 3 1.09.06 E/F OUTLOOK 2003 (Short Course II) - Calendar, Tasks and Notes 3 1.09.06 E/F CERN EDMS - Introduction 8 5.09.06 E CERN EDMS MTF en pratique 4 6.09.06 F ANSYS Workbench 32 12-15.09.06 F CERN EDMS for Engineers 8 12.09.06 E Software Engineering in the Small and the Large 16 12-13.09.06 E LabVIEW Basics 2 16 14-15.09.06 E WORD 2003 (Short Course III) - HowTo... Work with long documents 3 15.09.06 E/F EXCEL 2003 (Short Course I) - HowTo... Wor...

  17. Technical Training: Places available

    CERN Multimedia

    Davide Vitè

    2006-01-01

    Places available as of 7.2.2006 (February-May course sessions) The number of places available may vary. Please check our Web site to find out the current availability. Places are available on the following courses: Title Hours Date Language WORD 2003 (Short Course II) - HowTo... Mail merge 3 09-02-06 E-F ACCESS 2003 - Level 1: ECDL M5 16 13 to 14-02-06 E-F OUTLOOK 2003 (Short Course II) - Calendar, Tasks and Notes 3 16-02-06 E-F WORD 2003 (Short Course III) - HowTo... Work with long documents 3 16-02-06 E-F CERN EDMS - Introduction 8 21.02.06 E OUTLOOK 2003 (Short Course III) - Meetings and Delegation 3 27-02-06 E-F WORD 2003 (Short Course IV) - HowTo... Work with master document 3 27-02-06 E-F JAVA: Level 2 32 28-02-06 to 03-03-06 E Manipulation des images 4 28.02.06 F ACCESS 2003 - Level 2: ECDL AM5 16 02 to 03-03-06 E-F FrontPage 2003 - niveau 2 16 02 to 03-03-06 F C++ for Particle Physicists 20 06 to 10-03-06 E FileMaker - niv...

  18. Technical Training: Places available

    CERN Multimedia

    Davide Vitè

    2006-01-01

    Places available as of 21.3.2006 (March-October course sessions) The number of places available may vary. Please check our Web site to find out the current availability. Places are available on the following courses: Title Hours Date Language FrontPage 2003 - niveau 1 16 27-28.03.06 F Oracle Forms Developer 10g: Move to the Web 16 27-28.03.06 E ACCESS 2003 - Level 2: ECDL AM5 16 3-4.03.06 E-F JAVA 2 Enterprise Edition - Part 1: Web Applications 16 3-4.04.06 E JAVA 2 Enterprise Edition - Part 2: Enterprise JavaBeans 24 5-7.04.06 E AutoCAD Mechanical 2006 16 11-12.04.06 F FrontPage 2003 - niveau 2 16 24-25.04.06 F C++ Programming Part 1 - Introduction to Object-Oriented Design and Programming 24 25-27.04.06 E AutoCAD 2006 - niveau 1 32 27.04-4.05.06 F Oracle: SQL 24 3-5.05.06 E EXCEL 2003 (Short Course I) - HowTo... Work with formulae 3 4.05.06 (am) E-F EXCEL 2003 (Short Course II) - HowTo... Format your worksheet for printing 3 4...

  19. Technical Training: Places available

    CERN Multimedia

    Davide Vitè

    2006-01-01

    Places available as of 7.2.2006 (February-May course sessions) The number of places available may vary. Please check our Web site to find out the current availability. Places are available on the following courses: Title Hours Date Language WORD 2003 (Short Course II) - HowTo... Mail merge 3 13.03.06 E-F EXCEL 2003 (Short Course III) - HowTo... Pivot tables 3 20.03.06 E-F EXCEL 2003 (Short Course IV) - HowTo....Link cells, worksheets and workbooks 3 20.03.06 E-F Object-Oriented Analysis and Design using UML 24 21-23.03.06 E EXCEL 2003 - niveau 1 16 22-23.03.06 F FrontPage 2003 - niveau 1 16 27-28.03.06 F Oracle Forms Developer 10g: Move to the Web 16 27-28.03.06 E Oracle JDeveloper 10g: Build Applications with ADF 24 29-31.03.06 E ACCESS 2003 - Level 2: ECDL AM5 16 3-4.03.06 E-F JAVA 2 Enterprise Edition - Part 1: Web Applications 16 3-4.04.06 E JCOP: Control System Integration using JCOP Tools 24 4-6.04.06 E JAVA 2 Enterprise Edition...

  20. Technical Training: Places available

    CERN Multimedia

    Davide Vitè

    2006-01-01

    Places available as of 7.2.2006 (February-May course sessions) The number of places available may vary. Please check our Web site to find out the current availability. Places are available on the following courses: Title Hours Date Language WORD 2003 (Short Course IV) - HowTo... Work with master document 3 27.02.06 E-F JAVA: Level 2 32 28.02-3.03.06 E Manipulation des images 4 28.02.06 F ACCESS 2003 - Level 2: ECDL AM5 16 2-3.03.06 E-F C++ for Particle Physicists 20 6-10.03.06 E PowerPoint 2003 8 9.03.06 F JCOP: Control System Integration using JCOP Tools 24 14-16.03.06 E EXCEL 2003 (Short Course III) - HowTo... Pivot tables 3 20.03.06 E-F EXCEL 2003 (Short Course IV) - HowTo....Link cells, worksheets and workbooks 3 20.03.06 E-F JCOP: Finite State Machines in the JCOP Framework 24 21-23.03.06 E Object-Oriented Analysis and Design using UML 24 21-23.03.06 E FrontPage 2003 - niveau 1 16 27-28.03.06 F JCOP: Joint PVSS-JCOP Fram...

  1. Vector Fields on Product Manifolds

    OpenAIRE

    Kurz, Stefan

    2011-01-01

    This short report establishes some basic properties of smooth vector fields on product manifolds. The main results are: (i) On a product manifold there always exists a direct sum decomposition into horizontal and vertical vector fields. (ii) Horizontal and vertical vector fields are naturally isomorphic to smooth families of vector fields defined on the factors. Vector fields are regarded as derivations of the algebra of smooth functions.

  2. Resolution 519/012. It is allowed to R DEL SUR S.A company to generate a wind electricity source by a generating power plant placed in Maldonado province 2nd and 4th Catastral section, as well as the connection to the Interconnected National System

    International Nuclear Information System (INIS)

    2012-01-01

    The Resolution 519 is according to the Electric Wholesale Market regulation and it authorizes the power generation using the wind as the primary source. The company who presented this project was R DEL SUR S.A with the aim to instal a wind power plant in Maldonado province.

  3. Flying with the wind: Scale dependency of speed and direction measurements in modelling wind support in avian flight

    Science.gov (United States)

    Safi, Kamran; Kranstauber, Bart; Weinzierl, Rolf P.; Griffin, Larry; Reese, Eileen C.; Cabot, David; Cruz, Sebastian; Proaño, Carolina; Takekawa, John Y.; Newman, Scott H.; Waldenström, Jonas; Bengtsson, Daniel; Kays, Roland; Wikelski, Martin; Bohrer, Gil

    2013-01-01

    Background: Understanding how environmental conditions, especially wind, influence birds' flight speeds is a prerequisite for understanding many important aspects of bird flight, including optimal migration strategies, navigation, and compensation for wind drift. Recent developments in tracking technology and the increased availability of data on large-scale weather patterns have made it possible to use path annotation to link the location of animals to environmental conditions such as wind speed and direction. However, there are various measures available for describing not only wind conditions but also the bird's flight direction and ground speed, and it is unclear which is best for determining the amount of wind support (the length of the wind vector in a bird’s flight direction) and the influence of cross-winds (the length of the wind vector perpendicular to a bird’s direction) throughout a bird's journey.Results: We compared relationships between cross-wind, wind support and bird movements, using path annotation derived from two different global weather reanalysis datasets and three different measures of direction and speed calculation for 288 individuals of nine bird species. Wind was a strong predictor of bird ground speed, explaining 10-66% of the variance, depending on species. Models using data from different weather sources gave qualitatively similar results; however, determining flight direction and speed from successive locations, even at short (15 min intervals), was inferior to using instantaneous GPS-based measures of speed and direction. Use of successive location data significantly underestimated the birds' ground and airspeed, and also resulted in mistaken associations between cross-winds, wind support, and their interactive effects, in relation to the birds' onward flight.Conclusions: Wind has strong effects on bird flight, and combining GPS technology with path annotation of weather variables allows us to quantify these effects for

  4. Wind Power Meteorology

    DEFF Research Database (Denmark)

    Lundtang Petersen, Erik; Mortensen, Niels Gylling; Landberg, Lars

    Wind power meteorology has evolved as an applied science, firmly founded on boundary-layer meteorology, but with strong links to climatology and geography. It concerns itself with three main areas: siting of wind turbines, regional wind resource assessment, and short-term prediction of the wind...... resource. The history, status and perspectives of wind power meteorology are presented, with emphasis on physical considerations and on its practical application. Following a global view of the wind resource, the elements of boundary layer meteorology which are most important for wind energy are reviewed......: wind profiles and shear, turbulence and gust, and extreme winds. The data used in wind power meteorology stem mainly from three sources: onsite wind measurements, the synoptic networks, and the re-analysis projects. Wind climate analysis, wind resource estimation and siting further require a detailed...

  5. "From this place and of this place:" climate change, sense of place, and health in Nunatsiavut, Canada.

    Science.gov (United States)

    Cunsolo Willox, Ashlee; Harper, Sherilee L; Ford, James D; Landman, Karen; Houle, Karen; Edge, Victoria L

    2012-08-01

    As climate change impacts are felt around the globe, people are increasingly exposed to changes in weather patterns, wildlife and vegetation, and water and food quality, access and availability in their local regions. These changes can impact human health and well-being in a variety of ways: increased risk of foodborne and waterborne diseases; increased frequency and distribution of vector-borne disease; increased mortality and injury due to extreme weather events and heat waves; increased respiratory and cardiovascular disease due to changes in air quality and increased allergens in the air; and increased susceptibility to mental and emotional health challenges. While climate change is a global phenomenon, the impacts are experienced most acutely in place; as such, a sense of place, place-attachment, and place-based identities are important indicators for climate-related health and adaptation. Representing one of the first qualitative case studies to examine the connections among climate change, a changing sense of place, and health in an Inuit context, this research draws data from a multi-year community-driven case study situated in the Inuit community of Rigolet, Nunatsiavut, Canada. Data informing this paper were drawn from the narrative analysis of 72 in-depth interviews conducted from November 2009 to October 2010, as well as from the descriptive analysis of 112 questionnaires from a survey in October 2010 (95% response rate). The findings illustrated that climate change is negatively affecting feelings of place attachment by disrupting hunting, fishing, foraging, trapping, and traveling, and changing local landscapes-changes which subsequently impact physical, mental, and emotional health and well-being. These results also highlight the need to develop context-specific climate-health planning and adaptation programs, and call for an understanding of place-attachment as a vital indicator of health and well-being and for climate change to be framed as an

  6. A static investigation of yaw vectoring concepts on two-dimensional convergent-divergent nozzles

    Science.gov (United States)

    Berrier, B. L.; Mason, M. L.

    1983-01-01

    The flow-turning capability and nozzle internal performance of yaw-vectoring nozzle geometries were tested in the NASA Langley 16-ft Transonic wind tunnel. The concept was investigated as a means of enhancing fighter jet performance. Five two-dimensional convergent-divergent nozzles were equipped for yaw-vectoring and examined. The configurations included a translating left sidewall, left and right sidewall flaps downstream of the nozzle throat, left sidewall flaps or port located upstream of the nozzle throat, and a powered rudder. Trials were also run with 20 deg of pitch thrust vectoring added. The feasibility of providing yaw-thrust vectoring was demonstrated, with the largest yaw vector angles being obtained with sidewall flaps downstream of the nozzle primary throat. It was concluded that yaw vector designs that scoop or capture internal nozzle flow provide the largest yaw-vector capability, but decrease the thrust the most.

  7. Wind Energy Basics | NREL

    Science.gov (United States)

    Wind Energy Basics Wind Energy Basics We have been harnessing the wind's energy for hundreds of grinding grain. Today, the windmill's modern equivalent-a wind turbine can use the wind's energy to most energy. At 100 feet (30 meters) or more aboveground, they can take advantage of the faster and

  8. Prospecting for Wind

    Science.gov (United States)

    Swapp, Andy; Schreuders, Paul; Reeve, Edward

    2011-01-01

    Many people use wind to help meet their needs. Over the years, people have been able to harness or capture the wind in many different ways. More recently, people have seen the rebirth of electricity-generating wind turbines. Thus, the age-old argument about technology being either good or bad can also be applied to the wind. The wind can be a…

  9. Careers in Wind Energy

    Science.gov (United States)

    Liming, Drew; Hamilton, James

    2011-01-01

    As a common form of renewable energy, wind power is generating more than just electricity. It is increasingly generating jobs for workers in many different occupations. Many workers are employed on wind farms: areas where groups of wind turbines produce electricity from wind power. Wind farms are frequently located in the midwestern, western, and…

  10. Bunyavirus-Vector Interactions

    Directory of Open Access Journals (Sweden)

    Kate McElroy Horne

    2014-11-01

    Full Text Available The Bunyaviridae family is comprised of more than 350 viruses, of which many within the Hantavirus, Orthobunyavirus, Nairovirus, Tospovirus, and Phlebovirus genera are significant human or agricultural pathogens. The viruses within the Orthobunyavirus, Nairovirus, and Phlebovirus genera are transmitted by hematophagous arthropods, such as mosquitoes, midges, flies, and ticks, and their associated arthropods not only serve as vectors but also as virus reservoirs in many cases. This review presents an overview of several important emerging or re-emerging bunyaviruses and describes what is known about bunyavirus-vector interactions based on epidemiological, ultrastructural, and genetic studies of members of this virus family.

  11. Sums and Gaussian vectors

    CERN Document Server

    Yurinsky, Vadim Vladimirovich

    1995-01-01

    Surveys the methods currently applied to study sums of infinite-dimensional independent random vectors in situations where their distributions resemble Gaussian laws. Covers probabilities of large deviations, Chebyshev-type inequalities for seminorms of sums, a method of constructing Edgeworth-type expansions, estimates of characteristic functions for random vectors obtained by smooth mappings of infinite-dimensional sums to Euclidean spaces. A self-contained exposition of the modern research apparatus around CLT, the book is accessible to new graduate students, and can be a useful reference for researchers and teachers of the subject.

  12. Duality in vector optimization

    CERN Document Server

    Bot, Radu Ioan

    2009-01-01

    This book presents fundamentals and comprehensive results regarding duality for scalar, vector and set-valued optimization problems in a general setting. After a preliminary chapter dedicated to convex analysis and minimality notions of sets with respect to partial orderings induced by convex cones a chapter on scalar conjugate duality follows. Then investigations on vector duality based on scalar conjugacy are made. Weak, strong and converse duality statements are delivered and connections to classical results from the literature are emphasized. One chapter is exclusively consecrated to the s

  13. Multithreading in vector processors

    Science.gov (United States)

    Evangelinos, Constantinos; Kim, Changhoan; Nair, Ravi

    2018-01-16

    In one embodiment, a system includes a processor having a vector processing mode and a multithreading mode. The processor is configured to operate on one thread per cycle in the multithreading mode. The processor includes a program counter register having a plurality of program counters, and the program counter register is vectorized. Each program counter in the program counter register represents a distinct corresponding thread of a plurality of threads. The processor is configured to execute the plurality of threads by activating the plurality of program counters in a round robin cycle.

  14. Matrix vector analysis

    CERN Document Server

    Eisenman, Richard L

    2005-01-01

    This outstanding text and reference applies matrix ideas to vector methods, using physical ideas to illustrate and motivate mathematical concepts but employing a mathematical continuity of development rather than a physical approach. The author, who taught at the U.S. Air Force Academy, dispenses with the artificial barrier between vectors and matrices--and more generally, between pure and applied mathematics.Motivated examples introduce each idea, with interpretations of physical, algebraic, and geometric contexts, in addition to generalizations to theorems that reflect the essential structur

  15. Free topological vector spaces

    OpenAIRE

    Gabriyelyan, Saak S.; Morris, Sidney A.

    2016-01-01

    We define and study the free topological vector space $\\mathbb{V}(X)$ over a Tychonoff space $X$. We prove that $\\mathbb{V}(X)$ is a $k_\\omega$-space if and only if $X$ is a $k_\\omega$-space. If $X$ is infinite, then $\\mathbb{V}(X)$ contains a closed vector subspace which is topologically isomorphic to $\\mathbb{V}(\\mathbb{N})$. It is proved that if $X$ is a $k$-space, then $\\mathbb{V}(X)$ is locally convex if and only if $X$ is discrete and countable. If $X$ is a metrizable space it is shown ...

  16. Scalar-vector bootstrap

    Energy Technology Data Exchange (ETDEWEB)

    Rejon-Barrera, Fernando [Institute for Theoretical Physics, University of Amsterdam,Science Park 904, Postbus 94485, 1090 GL, Amsterdam (Netherlands); Robbins, Daniel [Department of Physics, Texas A& M University,TAMU 4242, College Station, TX 77843 (United States)

    2016-01-22

    We work out all of the details required for implementation of the conformal bootstrap program applied to the four-point function of two scalars and two vectors in an abstract conformal field theory in arbitrary dimension. This includes a review of which tensor structures make appearances, a construction of the projectors onto the required mixed symmetry representations, and a computation of the conformal blocks for all possible operators which can be exchanged. These blocks are presented as differential operators acting upon the previously known scalar conformal blocks. Finally, we set up the bootstrap equations which implement crossing symmetry. Special attention is given to the case of conserved vectors, where several simplifications occur.

  17. Reciprocity relationships in vector acoustics and their application to vector field calculations.

    Science.gov (United States)

    Deal, Thomas J; Smith, Kevin B

    2017-08-01

    The reciprocity equation commonly stated in underwater acoustics relates pressure fields and monopole sources. It is often used to predict the pressure measured by a hydrophone for multiple source locations by placing a source at the hydrophone location and calculating the field everywhere for that source. A similar equation that governs the orthogonal components of the particle velocity field is needed to enable this computational method to be used for acoustic vector sensors. This paper derives a general reciprocity equation that accounts for both monopole and dipole sources. This vector-scalar reciprocity equation can be used to calculate individual components of the received vector field by altering the source type used in the propagation calculation. This enables a propagation model to calculate the received vector field components for an arbitrary number of source locations with a single model run for each vector field component instead of requiring one model run for each source location. Application of the vector-scalar reciprocity principle is demonstrated with analytic solutions for a range-independent environment and with numerical solutions for a range-dependent environment using a parabolic equation model.

  18. Wind flow around met masts

    Energy Technology Data Exchange (ETDEWEB)

    Heraud, P.; Masson, C.; Tusch, M. [Garrad Hassan Canada Inc., Ottawa, ON (Canada)

    2010-07-01

    This PowerPoint presentation discussed the impacts of meteorological masts on the measurement of wind resources. Two types of meteorological masts are used in wind power applications, namely lattice, and tubular masts. Anemometer accuracy can be impacted by the logger as well as by the instrumentation layout. The International Electrochemical Commission (IEC) recommends that anemometers are placed at a 45 degree angle from pre-dominant winds. However, the impact of turbulent flow around meteorological masts is poorly understood. The numerical model developed in the study included mass and momentum conservation models for tubular and lattice towers. Distortion level recommendations were presented. The study showed that distortion depends on the layout, and that IEC recommendations for instrumentation layouts need to be revised. tabs., figs.

  19. Empirical wind retrieval model based on SAR spectrum measurements

    Science.gov (United States)

    Panfilova, Maria; Karaev, Vladimir; Balandina, Galina; Kanevsky, Mikhail; Portabella, Marcos; Stoffelen, Ad

    The present paper considers polarimetric SAR wind vector applications. Remote-sensing measurements of the near-surface wind over the ocean are of great importance for the understanding of atmosphere-ocean interaction. In recent years investigations for wind vector retrieval using Synthetic Aperture Radar (SAR) data have been performed. In contrast with scatterometers, a SAR has a finer spatial resolution that makes it a more suitable microwave instrument to explore wind conditions in the marginal ice zones, coastal regions and lakes. The wind speed retrieval procedure from scatterometer data matches the measured radar backscattering signal with the geophysical model function (GMF). The GMF determines the radar cross section dependence on the wind speed and direction with respect to the azimuthal angle of the radar beam. Scatterometers provide information on wind speed and direction simultaneously due to the fact that each wind vector cell (WVC) is observed at several azimuth angles. However, SAR is not designed to be used as a high resolution scatterometer. In this case, each WVC is observed at only one single azimuth angle. That is why for wind vector determination additional information such as wind streak orientation over the sea surface is required. It is shown that the wind vector can be obtained using polarimetric SAR without additional information. The main idea is to analyze the spectrum of a homogeneous SAR image area instead of the backscattering normalized radar cross section. Preliminary numerical simulations revealed that SAR image spectral maxima positions depend on the wind vector. Thus the following method for wind speed retrieval is proposed. In the first stage of the algorithm, the SAR spectrum maxima are determined. This procedure is carried out to estimate the wind speed and direction with ambiguities separated by 180 degrees due to the SAR spectrum symmetry. The second stage of the algorithm allows us to select the correct wind direction

  20. Modeling and analysis of doubly fed induction generator wind energy systems

    CERN Document Server

    Fan, Lingling

    2015-01-01

    Wind Energy Systems: Modeling, Analysis and Control with DFIG provides key information on machine/converter modelling strategies based on space vectors, complex vector, and further frequency-domain variables. It includes applications that focus on wind energy grid integration, with analysis and control explanations with examples. For those working in the field of wind energy integration examining the potential risk of stability is key, this edition looks at how wind energy is modelled, what kind of control systems are adopted, how it interacts with the grid, as well as suitable study

  1. Emerging place image

    DEFF Research Database (Denmark)

    Ooi, Can-Seng; Peji´c Kristensen, Tatjana; Lomanová Pedersen, Zdenka

    2004-01-01

    and perceptions.This paper introduces the concept of the orientalist tourist gaze, and demonstrates howorientalism may manifest in tourism. Data on how these two countries are imagined werecollected in Denmark.Keywords: destination identity, host society-guest interaction, impact of tourism, orientalism......Tourism offers an arena through which a place identity is imagined, negotiated and contained.This paper compares the Czech Republic and Slovakia, and show how these countriesconstruct and assert their identities through tourism. They both share a common history asCzechoslovakia, however...

  2. Tourism Sociabilities and Place

    DEFF Research Database (Denmark)

    Bødker, Mads; Browning, David

    2013-01-01

    Proposing new design opportunities, this paper challenges received notions of tourism, arguing that tourism is fundamentally social and concerned with making place. This turn makes tourism not only a convenient testing ground for technology concepts, but increasingly also for more sensitive...... renderings of, and interventions in, tourism as a relational and social practice. Using examples from commercial, arts, and design projects, and providing excerpts from our own fieldwork and design workshops with tourists and locals, this paper outlines three challenges through a conceptual lens that we see...... as productive for appropriate interaction design of tourism technologies....

  3. Signs in Place

    DEFF Research Database (Denmark)

    Hamid, Salmiah Binti Abdul; Jensen, Ole B.; Silva, Victor

    Travelling in unfamiliar areas is usually very interesting, however it can also be stressful. People travel or move around in an urban space according to their needs, and the environment can also influence the way people move about from one place to another. If a person gets lost, a map or GPS can...... and geosemiotic studies with regards to the road traffic signs used in urban spaces. The paper ends with a discussion on how people choreograph their movement in their everyday life from two different perspectives: above vs. below....

  4. Signs In Place

    DEFF Research Database (Denmark)

    Hamid, Salmiah Binti Abdul; Jensen, Ole B.; Silva, Victor

    2012-01-01

    Travelling in unfamiliar areas is usually very interesting; however, it can also be stressful. People travel or move around in an urban space according to their needs, and the environment can influence the way people move about from one place to another. If a person gets lost, a map or GPS can...... and geosemiotic studies with regards to the road traffic signs used in urban spaces. The paper ends with a discussion on how people choreograph their movement in their everyday life from two different perspectives: above vs. below...

  5. The use of wind to produce energy in Ketodestrin province

    International Nuclear Information System (INIS)

    Shirani, E.; Ahmadkia, H.; Talebi, F.; Mojib, J.

    2004-01-01

    Productivity of oil and gas and their high cost benefit in matters than combustion, in one hand and their problem of environmental pollution when they are burnt, on the other hand attracted the decision markers in Iran to consider the wind energy as a good alternative for energy resources . It is especially important because of the existence of regions with high potential for wind energy in Iran. The Kurdestan province is one of the windy places in Iran that has not been considered for wind energy yet. In this paper, the general characteristics of the different kinds of winds which are blown throughout the year in Kurdestan province are considered firstly. Then by using the information from the stations in the sixth major cities in the province, the wind characteristics including power, direction, intensity and probability at different months of the year, are considered. The statistical studies show that Bijar, Zarine Obatoo, Ghorveh, Sanandaj and Marivan have the most wind energy potential, and Bijar and Ghorveh are the best places to install the wind turbine. for all of the above regions, the maximum of the wind average speed and powe are obtained in March, April. May, and the minimum of the average wind speed occurs in December. Bijar, Ghorveh and Zarine Obatoo have high average wind speed and its recommended to search for best places in these regions for the wind turbine sites

  6. Estimation of vector velocity

    DEFF Research Database (Denmark)

    2000-01-01

    Using a pulsed ultrasound field, the two-dimensional velocity vector can be determined with the invention. The method uses a transversally modulated ultrasound field for probing the moving medium under investigation. A modified autocorrelation approach is used in the velocity estimation. The new...

  7. Production of lentiviral vectors

    Directory of Open Access Journals (Sweden)

    Otto-Wilhelm Merten

    2016-01-01

    Full Text Available Lentiviral vectors (LV have seen considerably increase in use as gene therapy vectors for the treatment of acquired and inherited diseases. This review presents the state of the art of the production of these vectors with particular emphasis on their large-scale production for clinical purposes. In contrast to oncoretroviral vectors, which are produced using stable producer cell lines, clinical-grade LV are in most of the cases produced by transient transfection of 293 or 293T cells grown in cell factories. However, more recent developments, also, tend to use hollow fiber reactor, suspension culture processes, and the implementation of stable producer cell lines. As is customary for the biotech industry, rather sophisticated downstream processing protocols have been established to remove any undesirable process-derived contaminant, such as plasmid or host cell DNA or host cell proteins. This review compares published large-scale production and purification processes of LV and presents their process performances. Furthermore, developments in the domain of stable cell lines and their way to the use of production vehicles of clinical material will be presented.

  8. Orthogonalisation of Vectors

    Indian Academy of Sciences (India)

    The Gram-Schmidt process is one of the first things one learns in a course ... We might want to stay as close to the experimental data as possible when converting these vectors to orthonormal ones demanded by the model. The process of finding the closest or- thonormal .... is obtained by writing the matrix A = [aI, an], then.

  9. From vectors to mnesors

    OpenAIRE

    Champenois, Gilles

    2007-01-01

    The mnesor theory is the adaptation of vectors to artificial intelligence. The scalar field is replaced by a lattice. Addition becomes idempotent and multiplication is interpreted as a selection operation. We also show that mnesors can be the foundation for a linear calculus.

  10. Calculus with vectors

    CERN Document Server

    Treiman, Jay S

    2014-01-01

    Calculus with Vectors grew out of a strong need for a beginning calculus textbook for undergraduates who intend to pursue careers in STEM. fields. The approach introduces vector-valued functions from the start, emphasizing the connections between one-variable and multi-variable calculus. The text includes early vectors and early transcendentals and includes a rigorous but informal approach to vectors. Examples and focused applications are well presented along with an abundance of motivating exercises. All three-dimensional graphs have rotatable versions included as extra source materials and may be freely downloaded and manipulated with Maple Player; a free Maple Player App is available for the iPad on iTunes. The approaches taken to topics such as the derivation of the derivatives of sine and cosine, the approach to limits, and the use of "tables" of integration have been modified from the standards seen in other textbooks in order to maximize the ease with which students may comprehend the material. Additio...

  11. On vector equilibrium problem

    Indian Academy of Sciences (India)

    [G] Giannessi F, Theorems of alternative, quadratic programs and complementarity problems, in: Variational Inequalities and Complementarity Problems (eds) R W Cottle, F Giannessi and J L Lions (New York: Wiley) (1980) pp. 151±186. [K1] Kazmi K R, Existence of solutions for vector optimization, Appl. Math. Lett. 9 (1996).

  12. Vector-borne Infections

    Centers for Disease Control (CDC) Podcasts

    2011-04-18

    This podcast discusses emerging vector-borne pathogens, their role as prominent contributors to emerging infectious diseases, how they're spread, and the ineffectiveness of mosquito control methods.  Created: 4/18/2011 by National Center for Emerging Zoonotic and Infectious Diseases (NCEZID).   Date Released: 4/27/2011.

  13. Technical Training: Places available

    CERN Multimedia

    Monique Duval

    2004-01-01

    If you wish to participate in one of the following courses, please discuss with your supervisor and apply electronically directly from the course description pages that can be found on the Web at: http://www.cern.ch/Training/ or fill in an "application for training" form available from your Divisional Secretariat or from your DTO (Divisional Training Officer). Applications will be accepted in the order of their receipt. TECHNICAL TRAINING Monique Duval tel. 74924 technical.training@cern.ch The number of places available may vary. Please check our Web site to find out the current availability. Places are available in the following courses: C++ for Particle Physicists : 8 - 12.3.2004 (6 X 4-hour sessions) Introduction to the CERN EDMS : 9.3.2004 (1 day, free of charge) The EDMS MTF in Practice : 10.3.2004 (morning, free of charge) CLEAN-2002: Working in a Cleanroom : 10.3.2004 (afternoon, free of charge) The CERN EDMS for Engineers : 11.3.2004 (1 day, free of charge) LabVIEW hands-on (E):...

  14. Technical Training: Places available

    CERN Multimedia

    2004-01-01

    If you wish to participate in one of the following courses, please discuss with your supervisor and apply electronically directly from the course description pages that can be found on the Web at: http://www.cern.ch/Training/ or fill in an "application for training" form available from your Divisional Secretariat or from your DTO (Divisional Training Officer). Applications will be accepted in the order of their receipt. TECHNICAL TRAINING Monique Duval tel. 74924 technical.training@cern.ch The number of places available may vary. Please check our Web site to find out the current availability. Places are available in the following courses: LabVIEW base 1 : 25 - 27.2.2004(3 jours) Instructor-led WBTechT study or follow-up for Microsoft applications : 26.2.2004 (morning) CLEAN-2002 : Working in a Cleanroom : 10.3.2004 (afternoon - free of charge) C++ for Particle Physicists : 8 - 12.3.2004 (6 X 4-hour sessions) LabVIEW hands-on (E) : 16.3.2004 (afternoon) LabVIEW Basics 1 : 22 - 24.3.2004 ...

  15. Technical Training: Places available

    CERN Multimedia

    2004-01-01

    If you wish to participate in one of the following courses, please discuss with your supervisor and apply electronically directly from the course description pages that can be found on the Web at: http://www.cern.ch/Training/ or fill in an "application for training" form available from your Divisional Secretariat or from your DTO (Divisional Training Officer). Applications will be accepted in the order of their receipt. TECHNICAL TRAINING Monique Duval tel. 74924 technical.training@cern.ch The number of places available may vary. Please check our Web site to find out the current availability. Places are available in the following courses: Instructor-led WBTechT study for Microsoft applications :12.2.2004 (morning) Instructor-led WBTechT study or follow-up for Microsoft applications : 19.2.2004 (morning) LabVIEW TestStand I (E) : 23 & 24.2.2004 (2 days) LabVIEW base 1 : 25 - 27.2.2004 (3 jours) Instructor-led WBTechT study or follow-up for Microsoft applications : 19.2.2004 (morning) CLEAN-2002 ...

  16. Technical Training: Places available

    CERN Multimedia

    2004-01-01

    If you wish to participate in one of the following courses, please discuss with your supervisor and apply electronically directly from the course description pages that can be found on the Web at: http://www.cern.ch/Training/ or fill in an "application for training" form available from your Divisional Secretariat or from your DTO (Divisional Training Officer). Applications will be accepted in the order of their receipt. TECHNICAL TRAINING Monique Duval tel. 74924 technical.training@cern.ch The number of places available may vary. Please check our Web site to find out the current availability. Places are available in the following courses: Instructor-led WBTechT study or follow-up for Microsoft applications : 19.2.2004 (morning) LabVIEW TestStand I (E) : 23 & 24.2.2004 (2 days) LabVIEW base 1 : 25 - 27.2.2004 (3 jours) Instructor-led WBTechT study or follow-up for Microsoft applications : 26.2.2004 (morning) CLEAN-2002 : Working in a Cleanroom : 10.3.2004 (afternoon - free of charge) C++ for Pa...

  17. Technical Training: Places available

    CERN Multimedia

    Monique Duval

    2005-01-01

    The number of places available may vary. Please check our Web site to find out the current availability. Places are available on the following courses: Hands-on Object-Oriented Design and Programming with C++ : 22 - 24.3.2005 (3 days) FileMaker - niveau 2 : 4 & 5.4.2005 (2 jours) EMAG-2004 - Electromagnetic Design and Mathematical Optimization in Magnet Technology: 4- 14.4.2005 (8 x 3h) EXCEL 2003 - niveau 2 : 11 & 12.4.2005 (2 jours) LabVIEW Intermediate 1: 11 - 13.4.2005 (3 days) ACCESS 2003 - Level 2 - ECDL AM5: 13 & 14.4.2005 (2 days) LabVIEW Intermediate 2: 14 & 15.4.2005 (2 days) PowerPoint 2003 (F) : 18.4.2005 (1 jour) Joint PVSS JCOP Framework : 25 - 29.4.2005 (5 days) WORD 2003 - niveau 1 : 2 & 3.5.2005 (2 jours) ELEC-2005 - Summer Term: System electronics for physics - Issues : 10, 12, 17, 19, 24, 26 & 31.5.2005 (7 x 2h lectures) AutoCAD 2002 - niveau 1 : 11, 12, 18 & 19.5.2005 (4 jour...

  18. Technical Training: Places available

    CERN Multimedia

    Monique Duval

    2004-01-01

    If you wish to participate in one of the following courses, please discuss with your supervisor and apply electronically directly from the course description pages that can be found on the Web at: http://www.cern.ch/Training/ or fill in an 'application for training' form available from your Divisional Secretariat or from your DTO (Divisional Training Officer). Applications will be accepted in the order of their receipt. The number of places available may vary. Please check our Web site to find out the current availability. Places are available in the following courses: Outlook (short course I) : E-mail : 31.8.2004 (2 hours, morning) Introduction à Outlook : Outlook (short course II) : Calendar, Tasks and Notes : 31.8.2004 (2 hours, afternoon) Instructor-led WBTechT Study or Follow-up for Microsoft Applications : 7.9.2004 (morning) Outlook (short course III) : Meetings and Delegation : 7.9.2004 (2 hours, afternoon) Introduction au VHDL et utilisation du simulateur ...

  19. Technical Training: Places available

    CERN Multimedia

    Monique Duval

    2004-01-01

    If you wish to participate in one of the following courses, please discuss with your supervisor and apply electronically directly from the course description pages that can be found on the Web at: http://www.cern.ch/Training/ or fill in an 'application for training' form available from your Divisional Secretariat or from your DTO (Divisional Training Officer). Applications will be accepted in the order of their receipt. The number of places available may vary. Please check our Web site to find out the current availability. Places are available in the following courses: Joint PVSS JCOP Framework : 9 - 13.8.2004 (5 days) Introduction à Outlook : 19.8.2004 (1 jour) Outlook (Short Course I): E-mail: 31.8.2004 (2 hours, morning) Outlook (Short Course II): Calendar, Tasks and Notes: 31.8.2004 (2 hours, afternoon) Instructor-led WBTechT Study or Follow-up for Microsoft Applications: 7.9.2004 (morning) Outlook (Short Course III): Meetings and Delegation: 7.9.2004 (2 hours, afternoon) I...

  20. Technical Training: Places available

    CERN Multimedia

    Monique Duval

    2004-01-01

    If you wish to participate in one of the following courses, please discuss with your supervisor and apply electronically directly from the course description pages that can be found on the Web at: http://www.cern.ch/Training/ or fill in an 'application for training' form available from your Divisional Secretariat or from your DTO (Divisional Training Officer). Applications will be accepted in the order of their receipt. The number of places available may vary. Please check our Web site to find out the current availability. Places are available in the following courses: Joint PVSS JCOP Framework : 9 - 13.8.2004 (5 days) Introduction à Outlook : 19.8.2004 (1 jour) Outlook (Short Course I): E-mail: 31.8.2004 (2 hours, morning) Outlook (Short Course II): Calendar, Tasks and Notes: 31.8.2004 (2 hours, afternoon) Hands-on Introduction to Python Programming: 1 - 3.9.2004 (3 days - free course) Instructor-led WBTechT Study or Follow-up for Microsoft Applications: 7.9.20...

  1. Technical Training: Places available

    CERN Multimedia

    Monique Duval

    2004-01-01

    The number of places available may vary. Please check our Web site to find out the current availability. Places are available in the following courses: Introduction à ANSYS : 23 - 26.11.2004 (4 jours) FileMaker - niveau 1 : 23 - 26.11.2004 (4 jours) Project Planning with MS-Project : 25.11 & 2.12.2004 (2 days) Explicit Dynamics with ANSYS/LS-Dyna : 7 - 9.12.2004 (3 days) Introduction to PERL 5 : 8 & 9.12.2004 (2 days) PCAD Schémas - Débutants : 9 & 10.12.2004 (2 jours) The JAVA Programming Language Level 1 : 11 & 12.1.2005 (2 days) Introduction to XML : 13 & 14.1.2005 (2 days) Introduction to the CERN EDMS : 18.1.2005 (1 day - free course) The CERN EDMS for Local Administrators : 19 & 20.1.2005 (2 days - free course) Programmation Unity-Pro pour utilisateurs de Schneider PL7-Pro : 24 - 28.1.2005 (8 demi-journées) CLEAN-2002 : Travaill...

  2. Technical Training: Places available

    CERN Multimedia

    Monique Duval

    2004-01-01

    The number of places available may vary. Please check our Web site to find out the current availability. Places are available in the following courses: Explicit Dynamics with ANSYS/LS-Dyna : 7 - 9.12.2004 (3 days) Introduction to PERL 5 : 8 & 9.12.2004 (2 days) PCAD Schémas - Débutants : 9 & 10.12.2004 (2 jours) Advanced aspects of PERL 5: 10.12.2004 (1 day) PCAD PCB – Débutants : 13 - 15.12.2004 (3 jours) The JAVA Programming Language Level 1 : 11 & 12.1.2005 (2 days) Introduction to XML : 13 & 14.1.2005 (2 days) Introduction to the CERN EDMS : 18.1.2005 (1 day - free course) The CERN EDMS for Local Administrators : 19 & 20.1.2005 (2 days - free course) Programmation Unity-Pro pour utilisateurs de Schneider PL7-Pro : 24 - 28.1.2005 (8 demi-journées) CLEAN-2002 : Travailler en salle propre : 25.1.2005 (après-midi, cours gratuit) Compatibilit&eac...

  3. Technical Training: Places available

    CERN Multimedia

    Monique Duval

    2004-01-01

    The number of places available may vary. Please check our Web site to find out the current availability. Places are available in the following courses: FileMaker - niveau 1 : 23 - 26.11.2004 (4 jours) Explicit Dynamics with ANSYS/LS-Dyna : 7 - 9.12.2004 (3 days) Introduction to PERL 5 : 8 & 9.12.2004 (2 days) PCAD Schémas - Débutants : 9 & 10.12.2004 (2 jours) Advanced aspects of PERL 5: 10.12.2004 (1 day) PCAD PCB – Débutants : 13 - 15.12.2004 (3 jours) The JAVA Programming Language Level 1 : 11 & 12.1.2005 (2 days) Introduction to XML : 13 & 14.1.2005 (2 days) Introduction to the CERN EDMS : 18.1.2005 (1 day - free course) The CERN EDMS for Local Administrators : 19 & 20.1.2005 (2 days - free course) Programmation Unity-Pro pour utilisateurs de Schneider PL7-Pro : 24 - 28.1.2005 (8 demi-journées) CLEAN-2002 : Travailler en salle propre : 25.1.2005 ...

  4. Technical Training: Places available

    CERN Multimedia

    Monique Duval

    2004-01-01

    The number of places available may vary. Please check our Web site to find out the current availability. Places are available in the following courses: C++ for Particle Physicists : 15 - 19.11.2004 (6 X 3 hours sessions) Word 2003 - niveau 1 : 22 & 23.11.2004 (2 jours) Introduction à ANSYS : 23 - 26.11.2004 (4 jours) Project Planning with MS-Project : 25.11 & 2.12.2004 (2 days) Explicit Dynamics with ANSYS/LS-Dyna : 7 - 9.12.2004 (2 days) PCAD Schémas - Débutants : 9 & 10.12.2004 (2 jours) The JAVA Programming Language Level 1 : 11 & 12.1.2005 (2 days) Introduction to XML : 13 & 14.1.2005 (2 days) CLEAN-2002 : Travailler en salle propre : 25.1.2005 (après-midi, cours gratuit) Compatibilité électromagnétique (CEM) : installation et remèdes : 25 - 27.1.2005 (3 jours) Finite State Machines in the JCOP Fr ...

  5. Technical Training: Places available

    CERN Multimedia

    2004-01-01

    If you wish to participate in one of the following courses, please discuss with your supervisor and apply electronically directly from the course description pages that can be found on the Web at: http://www.cern.ch/Training/ or fill in an "application for training" form available from your Divisional Secretariat or from your DTO (Divisional Training Officer). Applications will be accepted in the order of their receipt. TECHNICAL TRAINING Monique Duval tel. 74924 technical.training@cern.ch The number of places available may vary. Please check our Web site to find out the current availability. Places are available in the following courses: C++ for Particle Physicists : 8 - 12.3.2004 (6 X 4-hour sessions) Introduction to the CERN EDMS : 9.3.2004 (1 day, free of charge) The EDMS MTF in Practice : 10.3.2004 (morning, free of charge) CLEAN-2002 : Working in a Cleanroom : 10.3.2004 (afternoon, free of charge) The CERN EDMS for Engineers : 11.3.2004 (1 day, free of charge) LabVIEW...

  6. Technical Training: Places available

    CERN Multimedia

    Monique Duval

    2004-01-01

    If you wish to participate in one of the following courses, please discuss with your supervisor and apply electronically directly from the course description pages that can be found on the Web at: http://www.cern.ch/Training/ or fill in an 'application for training' form available from your Divisional Secretariat or from your DTO (Divisional Training Officer). Applications will be accepted in the order of their receipt. The number of places available may vary. Please check our Web site to find out the current availability. Places are available in the following courses: AutoCAD 2002 - niveau 1 : 13, 14, 23, 24.09.2004 (4 jours) Introduction to the CERN EDMS : 22.6.2004 (1 day) The CERN EDMS for local administrators : 23 & 24.6.2004 (2 days) MAGNE-04 : Magnétisme pour l'électrotechnique : 6 - 8.7.2004 (3 jours) Introduction au VHDL et utilisation du simulateur NCVHDL de CADENCE : 7 & 8.9.2004 (2 jours) ENSEIGNEMENT TECHNIQUE TECHNICAL TRAINING...

  7. Technical Training: Places available

    CERN Document Server

    Monique Duval

    2004-01-01

    If you wish to participate in one of the following courses, please discuss with your supervisor and apply electronically directly from the course description pages that can be found on the Web at: http://www.cern.ch/Training/ or fill in an 'application for training' form available from your Divisional Secretariat or from your DTO (Divisional Training Officer). Applications will be accepted in the order of their receipt. The number of places available may vary. Please check our Web site to find out the current availability. Places are available in the following courses: Joint PVSS JCOP Programming : 9 - 13.8.2004 (5 days) Hands-on Introduction to Python Programming: 1 - 3.9.2004 (3 days - free course) Introduction au VHDL et utilisation du simulateur NCVHDL de CADENCE : 7 & 8.9.2004 (2 jours) Joint PVSS JCOP Programming : 13 - 17.9.2004 (5 days) AutoCAD 2002 - niveau 1 : 13, 14, 23, 24.9.2004 (4 jours) Programmation STEP7 niveau 1 : 14-17.9.2004 (4...

  8. Technical Training: Places available**

    CERN Multimedia

    2004-01-01

    If you wish to participate in one of the following courses, please discuss with your supervisor and apply electronically directly from the course description pages that can be found on the Web at: http://www.cern.ch/Training/ or fill in an "application for training" form available from your Divisional Secretariat or from your DTO (Divisional Training Officer). Applications will be accepted in the order of their receipt. TECHNICAL TRAINING Monique Duval tel. 74924 technical.training@cern.ch ** The number of places available may vary. Please check our Web site to find out the current availability. Places are available in the following courses: The JAVA Programming Language Level 1 : 9 & 10.1.2004 (2 days) LabVIEW TestStand I (E) : 23 & 24.2.2004 (2 days) LabVIEW base 1 : 25 - 27.2.2004 (3 jours) CLEAN-2002 : Working in a Cleanroom : 10.3.2004 (afternoon - free of charge) C++ for Particle Physicists : 8 - 12.3.2004 ( 6 X 4-hour sessions) LabVIEW hands-on (E) 16.3...

  9. Technical Training: Places available

    CERN Multimedia

    Monique Duval

    2004-01-01

    If you wish to participate in one of the following courses, please discuss with your supervisor and apply electronically directly from the course description pages that can be found on the Web at: http://www.cern.ch/Training/ or fill in an 'application for training' form available from your Divisional Secretariat or from your DTO (Divisional Training Officer). Applications will be accepted in the order of their receipt. The number of places available may vary. Please check our Web site to find out the current availability. Places are available in the following courses: Introduction to the CERN EDMS : 22.6.2004 (1 day) The CERN EDMS for local administrators : 23 & 24.6.2004 (2 days) Compatibilité électromagnétique (CEM) - Introduction / Electromagnetic Compatibility (EMC) - Introduction: 7.7.2004 (morning) Introduction au VHDL et utilisation du simulateur NCVHDL de CADENCE : 7 & 8.9.2004 (2 jours) AutoCAD 2002 - niveau 1 : 13, 14, 23, 24.9.2004 (4 jours) Programmation STEP...

  10. Technical Training: Places available

    CERN Multimedia

    Monique Duval

    2004-01-01

    The number of places available may vary. Please check our Web site to find out the current availability. Places are available in the following courses: LabVIEW Intermediate I : 8 - 10.11.2004 (3 days) Instructor-led WTechT Study or Follow-up for Microsoft Applications : 9.11.2004 (morning) Hands-On Object Oriented Design and Programming with C++ : 9 - 11.11.2004 (3 days) Outlook (Short Course III) : Meetings and Delegation : 9.11.2004 (2 hours, afternoon) LabVIEW Intermediate II : 11 & 12.11.2004 (2 days) AutoCAD 2002 - niveau 1 : 11, 12, 18, 19.11.2004 (4 jours) C++ for Particle Physicists : 15 - 19.11.2004 (6 X 3 hours sessions) Word 2003 - niveau 1 : 22 & 23.11.2004 (2 jours) Introduction à ANSYS : 23 - 26.11.2004 (4 jours) CLEAN-2002 - Travailler en salle propre : 23.11.2004 (après-midi, cours gratuit) Project Planning with MS-Project : 25.11 & 2.12.2004 (2 days) ENSEIGNEMENT ...

  11. Technical training: Places available

    CERN Multimedia

    Monique Duval

    2004-01-01

    The number of places available may vary. Please check our Web site to find out the current availability. Places are available in the following courses: LabVIEW Intermediate I : 8 - 10.11.2004 (3 days) Instructor-led WTechT Study or Follow-up for Microsoft Applications : 9.11.2004 (morning) Outlook (Short Course III) : Meetings and Delegation : 9.11.2004 (2 hours, afternoon) LabVIEW Intermediate II : 11 & 12.11.2004 (2 days) AutoCAD 2002 - niveau 1 : 11, 12, 18, 19.11.2004 (4 jours) C++ for Particle Physicists : 15 - 19.11.2004 (6 X 3 hours sessions) Word 2003 - niveau 1 : 22 & 23.11.2004 (2 jours) Introduction à ANSYS : 23 - 26.11.2004 (4 jours) Project Planning with MS-Project : 25.11 & 2.12.2004 (2 days) Introduction to PERL 5 : 8 & 9.12.2004 (2 days) Advanced aspects of PERL 5 : 10.12.2004 (1 day) The JAVA Programming Language Level 1 : 11 & 12.1.2005 (2 days) Introduction...

  12. Technical Training: Places available

    CERN Multimedia

    2004-01-01

    If you wish to participate in one of the following courses, please discuss with your supervisor and apply electronically directly from the course description pages that can be found on the Web at: http://www.cern.ch/Training/ or fill in an "application for training" form available from your Divisional Secretariat or from your DTO (Divisional Training Officer). Applications will be accepted in the order of their receipt. TECHNICAL TRAINING Monique Duval tel. 74924 technical.training@cern.ch The number of places available may vary. Please check our Web site to find out the current availability. Places are available in the following courses: Project Planning with MS-Project :6 & 13.5.2004 (2 days) Word 2003 - niveau 1 : 10 & 11.5.2004 (2 jours) Oracle 9i : SQL : 17 - 19.5.2004 (3 days) Word 2003 - niveau 2 : 24 & 25.5.2004 (2 jours) EXCEL 2003 - niveau 1: 27 & 28.5.2004 (2 jours) STEP7 Programming Level 1 : 1 - 4.6.2004 (4 days) Oracle 9i : Programming with PL/SQL : 2 - 4.6.2...

  13. Technical Training: Places available

    CERN Multimedia

    Monique Duval

    2005-01-01

    The number of places available may vary. Please check our Web site to find out the current availability. Places are available on the following courses: Finite State Machines in the JCOP Framework:  26 - 28.9.2005 (3 days) WORD 2003 (Short Course IV) - HowTo... Work with master document: 28.9.2005 (morning) Joint PVSS JCOP Framework : 3 - 7.10.2005 (5 days) Introduction à Dreamweaver MX :  3 - 4.10.2005 (2 jours) Utilisation des fichiers PDF avec Acrobat 7.0 :   4.10.2005 (1 journée) LaTeX par la pratique :   4 - 6.10.2005 (3 matinées) PowerPoint 2003 (F) :  7.10.2005 (1 journée) FileMaker - niveau 1 :  20 - 21.10.2005 (2 jours) ACCESS 2003 - Level 1 - ECDL M5: 24 - 25.10.2005 (2 days) EXCEL 2003 (Short Course III) - HowTo... Pivot tables: 26.10.2005 (morning) WORD 2003 (Short Course I) - HowTo... Work with AutoTasks: 26.10.2005 (afternoon) OUTLOOK (Short Course I) - E-mail: 2.11.2005 (morning) WORD 2003 (Short Course II) - HowTo... Mail merge: 2.11....

  14. Technical Training: Places available

    CERN Multimedia

    Davide Vitè

    2005-01-01

    Le nombre de places disponibles peut varier. Veuillez consulter notre site Web pour avoir la dernière mise à jour. Des places sont disponibles dans les cours suivants :   Finite State Machines in the JCOP Framework:  26 - 28.9.2005 (3 days) MAGNE-05 - Magnétisme pour l'électrotechnique : 27 - 29.9.2005 (3 jours) WORD 2003 (Short Course IV) - HowTo... Work with master document: 28.9.2005 (morning) Joint PVSS JCOP Framework : 3 - 7.10.2005 (5 days) Introduction à Dreamweaver MX :  3 - 4.10.2005 (2 jours) Utilisation des fichiers PDF avec Acrobat 7.0 :   4.10.2005 (1 journée) LaTeX par la pratique :   4 - 6.10.2005 (3 matinées) PowerPoint 2003 (F) :  7.10.2005 (1 journée) ACCESS 2003 - Level 1 - ECDL M5: 24 - 25.10.2005 (2 days) EXCEL 2003 (Short Course III) - HowTo... Pivot tables: 26.10.2005 (morning) WORD 2003 (Short Course I) - HowTo... Work with AutoTasks: 26.10.2005 (afternoon) OUTLOOK (Short Course I) - E-mail: 2.11.2005 (morning) WORD 2003 (...

  15. Technical Training: Places available

    CERN Multimedia

    Davide Vitè

    2005-01-01

    The number of places available may vary. Please check our Web site to find out the current availability. Places are available on the following courses: Introduction à Windows XP au CERN : 12.9.2005 (1 demi-journée) FrontPage 2003 - niveau 2 : 15 - 16.9.2005 (2 jours) Finite State Machines in the JCOP Framework:  26 - 28.9.2005 (3 days) MAGNE-05 - Magnétisme pour l'électrotechnique : 27 - 29.9.2005 (3 jours) WORD 2003 (Short Course IV) - HowTo... Work with master document: 28.9.2005 (morning) Joint PVSS JCOP Framework : 3 - 7.10.2005 (5 days) Introduction à Dreamweaver MX :  3 - 4.10.2005 (2 jours) Utilisation des fichiers PDF avec Acrobat 7.0 :   4.10.2005 (1 journée) LaTeX par la pratique :   4 - 6.10.2005 (3 matinées) PowerPoint 2003 (F) :  7.10.2005 (1 journée) ACCESS 2003 - Level 1 - ECDL M5: 24 - 25.10.2005 (2 days) EXCEL 2003 (Short Course III) - HowTo... Pivot tables: 26.10.2005 (morning) WORD 2003 (Short Course I) - HowTo... Work with Auto...

  16. Technical Training: Places available

    CERN Multimedia

    Monique Duval

    2005-01-01

    The number of places available may vary. Please check our Web site to find out the current availability. Places are available on the following courses: Joint PVSS JCOP Framework: 8 - 12.8.2005 (5 days) WORD 2003 (Short Course I) - HowTo... Work with AutoTasks (AutoText, AutoFormat, AutoCorrect, Lists, Find/Replace): 25.8.2005 (morning) WORD 2003 (Short Course II) - HowTo... Mail merge: 25.8.2005 (afternoon) EXCEL 2003 (Short Course I) - HowTo... Work with formulae: 26.8.2005 (morning) WORD 2003 (Short Course III) - HowTo... Work with long documents: 26.8.2005 (afternoon) FrontPage 2003 - niveau 1 : 1 - 2.9.2005 (2 jours) Utilisation des fichiers PDF avec ACROBAT 7.0 : 5.9.2005 (1 jour) LabVIEW Basics 1 : 5 - 7.9.2005 (3 days, dates to be confirmed) Introduction à Windows XP au CERN : 12.9.2005 (1 demi-journée) FrontPage 2003 - niveau 2 : 15 - 16.9.2005 (2 jours) AutoCAD 2005 - niveau 1 : 22, 23, 28, 29.9.2005 (4 jours) MAGNE-05 - Magn&...

  17. Technical Training: Places available

    CERN Multimedia

    Monique Duval

    2005-01-01

    The number of places available may vary. Please check our Web site to find out the current availability. Places are available on the following courses: Utilisation des fichiers PDF avec ACROBAT 7.0 : 5.9.2005 (1 jour) LabVIEW Basics 1:  5 - 7.9.2005 (3 days) Introduction à Windows XP au CERN : 12.9.2005 (1 demi-journée) FrontPage 2003 - niveau 2 : 15 - 16.9.2005 (2 jours) AutoCAD 2005 - niveau 1 : 22, 23, 28, 29.9.2005 (4 jours) Finite State Machines in the JCOP Framework:  26 - 28.9.2005 (3 days) MAGNE-05 - Magnétisme pour l'électrotechnique : 27 - 29.9.2005 (3 jours) WORD 2003 (Short Course IV) - HowTo... Work with master document: 28.9.2005 (morning) Joint PVSS JCOP Framework : 3 - 7.10.2005 (5 days) ACCESS 2003 - Level 1 - ECDL M5: 24 - 25.10.2005 (2 days) EXCEL 2003 (Short Course III) - HowTo... Pivot tables: 26.10.2005 (morning) WORD 2003 (Short Course I) - HowTo... Work with AutoTasks: 26.10.2005 (afternoon) OUTLOOK (Short Course I) - E-mail: 2...

  18. Technical Training: Places available

    CERN Multimedia

    Monique Duval

    2005-01-01

    The number of places available may vary. Please check our Web site to find out the current availability. Places are available on the following courses: Joint PVSS JCOP Framework: 8 - 12.8.2005 (5 days) WORD 2003 (Short Course I) - HowTo... Work with AutoTasks (AutoText, AutoFormat, AutoCorrect, Lists, Find/Replace): 25.8.2005 (morning) WORD 2003 (Short Course II) - HowTo... Mail merge: 25.8.2005 (afternoon) EXCEL 2003 (Short Course I) - HowTo... Work with formulae: 26.8.2005 (morning) WORD 2003 (Short Course III) - HowTo... Work with long documents: 26.8.2005 (afternoon) FrontPage 2003 - niveau 1 : 1 - 2.9.2005 (2 jours) Utilisation des fichiers PDF avec ACROBAT 7.0 : 5.9.2005 (1 jour) LabVIEW Basics 1 : 5 - 7.9.2005 (3 days, dates to be confirmed) Introduction à Windows XP au CERN : 12.9.2005 (1 demi-journée) FrontPage 2003 - niveau 2 : 15 - 16.9.2005 (2 jours) AutoCAD 2005 - niveau 1 : 22, 23, 28, 29.9.2005 (4 jours) Finite State Machines in the JCOP Framew...

  19. Technical Training: Places available

    CERN Multimedia

    Davide Vitè

    2006-01-01

    The number of places available may vary. Please check our Web site to find out the current availability. Places are available on the following courses: Title Hours Date Language AutoCAD Mechanical 2006 16 30 to 31-01-06 F DIAdem : base 24 01 to 03-02-06 F ACROBAT 7.0 : Utilisation de fichiers PDF 8 06-02-06 F Manipulation des images 4 08-02-06 F OUTLOOK 2003 (Short Course I) - E-mail 3 09-02-06 E-F WORD 2003 (Short Course II) - HowTo... Mail merge 3 09-02-06 E-F ACCESS 2003 - Level 1: ECDL M5 16 13 to 14-02-06 E-F JCOP: Control System Integration using JCOP Tools 24 14 to 16-02-06 E OUTLOOK 2003 (Short Course II) - Calendar, Tasks and Notes 3 16-02-06 E-F WORD 2003 (Short Course III) - HowTo... Work with long documents 3 16-02-06 E-F FrontPage 2003 - niveau 1 16 23 to 24-02-06 F OUTLOOK 2003 (Short Course III) - Meetings and Delegation 3 27-02-06 E-F WORD 2003 (Short Course IV) - HowTo... Work with master document 3 27-02-06 E-F ...

  20. Technical Training: Places available

    CERN Multimedia

    Davide Vitè

    2006-01-01

    The number of places available may vary. Please check our Web site to find out the current availability. Places are available on the following courses: Title Hours Date Language ACCESS 2003 - Level 2: ECDL AM5 16 19 to 20-01-06 E-F AutoCAD 2006 - niveau 1 32 19 to 25-01-06 F C++ Programming Advanced - Traps and Pitfalls 32 24 to 27-01-06 E STEP7 : Level 1 32 24 to 27-01-06 E LabVIEW Basics 2 16 26 to 27-01-06 E AutoCAD Mechanical 2006 16 30 to 31-01-06 F DIAdem : base 24 01 to 03-02-06 F FrontPage 2003 - niveau 1 16 02 to 03-02-06 F ACROBAT 7.0 : Utilisation de fichiers PDF 8 06-02-06 F Manipulation des images 4 08-02-06 F OUTLOOK 2003 (Short Course I) - E-mail 3 09-02-06 E-F WORD 2003 (Short Course II) - HowTo... Mail merge 3 09-02-06 E-F ACCESS 2003 - Level 1: ECDL M5 16 13 to 14-02-06 E-F JCOP: Control System Integration using JCOP Tools 24 14 to 16-02-06 E OUTLOOK 2003 (Short Course II) - Calendar, Tasks and Note...

  1. Technical Training: Places available

    CERN Multimedia

    Monique Duval

    2005-01-01

    The number of places available may vary. Please check our Web site to find out the current availability. Places are available on the following courses: WORD 2003 (Short Course I) - HowTo... Work with AutoTasks (AutoText, AutoFormat, AutoCorrect, Lists, Find/Replace): 25.8.2005 (morning) WORD 2003 (Short Course II) - HowTo... Mail merge: 25.8.2005 (afternoon) EXCEL 2003 (Short Course I) - HowTo... Work with formulae: 26.8.2005 (morning) WORD 2003 (Short Course III) - HowTo... Work with long documents: 26.8.2005 (afternoon) FrontPage 2003 - niveau 1 : 1 - 2.9.2005 (2 jours) Utilisation des fichiers PDF avec ACROBAT 7.0 : 5.9.2005 (1 jour) LabVIEW base 1 : 5 - 7.9.2005 (3 jours) Introduction à Windows XP au CERN : 12.9.2005 (1 demi-journée) FrontPage 2003 - niveau 2 : 15 - 16.9.2005 (2 jours) AutoCAD 2005 - niveau 1 : 22, 23, 28, 29.9.2005 (4 jours) Finite State Machines in the JCOP Framework:  26 - 28.9.2005 (3 days) MAGNE-05 - Magnétisme pour l'électrotechniq...

  2. Technical Training: Places available

    CERN Multimedia

    Monique Duval

    2005-01-01

    The number of places available may vary. Please check our Web site to find out the current availability. Places are available on the following courses: LabVIEW Real-Time (F) : 7 - 9.6.2005 (3 jours) LabVIEW Migration 6 to 7: 14.6.2005 (1 day) FrontPage 2003 - niveau 2 : 16 & 17.6.2005 (2 jours) Utilisation de fichiers PDF avec ACROBAT 6.0 : 20.6.2005 (1journée) Introduction to ANSYS: 21 - 24.6.2005 (4 days) WORD 2003 (Short Course I) - HowTo... Work with repetitive tasks /AutoText, AutoFormat, AutoCorrect, Find/Replace) : 4.7.2005 (afternoon) WORD 2003 (Short Course II) - HowTo... Mail merge: 5.7.2005 (afternoon) WORD 2003 (Short Course III) - HowTo... Work with long documents : 6.7.2005 (afternoon) ACCESS 2003 - Level 2 - ECDL AM5: 5 - 8.7.2005 (4 mornings) EXCEL 2003 (Short Course I) - HowTo... Work with formulae: 7.7.2005 (afternoon) EXCEL 2003 (Short Course II) - HowTo... Format your worksheet for printing: 8.7.2005 (aftern...

  3. Technical Training: Places available

    CERN Multimedia

    Monique Duval

    2005-01-01

    The number of places available may vary. Please check our Web site to find out the current availability. Places are available on the following courses: LabVIEW base 1 : 4 - 6.7.2005 (3 jours) LabVIEW Basics 2: 7 - 8.7.2005 (2 days) Utilisation des fichiers PDF avec ACROBAT 7.0 : 5.7.2005 (1 jour) FrontPage 2003 - niveau 1 : 6-7.7.2005 (2 jours) WORD 2003 (Short Course I) - HowTo... Work with repetitive tasks /AutoText, AutoFormat, AutoCorrect, Find/Replace) : 4.7.2005 (afternoon) WORD 2003 (Short Course II) - HowTo... Mail merge: 5.7.2005 (afternoon) WORD 2003 (Short Course III) - HowTo... Work with long documents : 6.7.2005 (afternoon) OUTLOOK (Short Course I) - E-mail: 6.7.2005 (morning) OUTLOOK (Short Course II) - Calendar, Tasks and Notes: 7.7.2005 (morning) OUTLOOK (Short Course III) - Meetings and Delegation: 8.7.2005 (morning) EXCEL 2003 (Short Course I) - HowTo... Work with formulae: 7.7.2005 (afternoon) EXCEL 2003 (Short Course II) - HowTo... Format y...

  4. Technical Training: Places available

    CERN Multimedia

    Monique Duval

    2005-01-01

    The number of places available may vary. Please check our Web site to find out the current availability. Places are available on the following courses: LabVIEW Real-Time (F) : 7 - 9.6.2005 (3 jours) LabVIEW Migration 6 to 7: 14.6.2005 (1 day) IT3T/1 - Read your mail and more with Outlook 2003 : 14.6.2005 (IT Technical Training Tutorial, free of charge) IT3T/2 - Creating, managing and using distribution lists with Simba2 : 16.6.2005 (IT Technical Training Tutorial, free of charge) FrontPage 2003 - niveau 2 : 16 & 17.6.2005 (2 jours) Utilisation de fichiers PDF avec ACROBAT 6.0 : 20.6.2005 (1journée) Introduction to ANSYS: 21 - 24.6.2005 (4 days) IT3T/3 - Working remotely with Windows XP : 28.6.2005 (IT Technical Training Tutorial, free of charge) IT3T/4 - Editing Websites with Frontpage 2003 : 30.6.2005 (IT Technical Training Tutorial, free of charge) WORD 2003 (Short Course I) - HowTo... Work with repetitive tasks /AutoText, AutoFormat, AutoC...

  5. Technical Training: Places available

    CERN Multimedia

    Monique Duval

    2005-01-01

    The number of places available may vary. Please check our Web site to find out the current availability. Places are available on the following courses: Hands-on Introduction to Python Programming: 28 - 30.6.2005 (3 days) Introduction to ANSYS: 28.6 - 1.7.2005 (4 days) IT3T/3 - Working remotely with Windows XP: 28.6.2005 (IT Technical Training Tutorial, free of charge) IT3T/4 - Editing Websites with Frontpage 2003: 30.6.2005 (IT Technical Training Tutorial, free of charge) LabVIEW base 1 : 4 - 6.7.2005 (3 jours) LabVIEW Basics 2: 7 - 8.7.2005 (2 days) Utilisation des fichiers PDF avec ACROBAT 7.0 : 5.7.2005 (1 jour) FrontPage 2003 - niveau 1 : 6-7.7.2005 (2 jours) WORD 2003 (Short Course I) - HowTo... Work with repetitive tasks /AutoText, AutoFormat, AutoCorrect, Find/Replace) : 4.7.2005 (afternoon) WORD 2003 (Short Course II) - HowTo... Mail merge: 5.7.2005 (afternoon) WORD 2003 (Short Course III) - HowTo... Work with long documents : 6.7.2005 (afternoon) ACCES...

  6. Technical Training: Places available

    CERN Multimedia

    Monique Duval

    2005-01-01

    The number of places available may vary. Please check our Web site to find out the current availability. Places are available on the following courses: Joint PVSS JCOP Framework: 8 - 12.8.2005 (5 days) FrontPage 2003 - niveau 1 : 1 - 2.9.2005 (2 jours) Utilisation des fichiers PDF avec ACROBAT 7.0 : 5.9.2005 (1 jour) LabVIEW Basics 1 : 5 - 7.9.2005 (3 days, dates to be confirmed) Introduction à Windows XP au CERN : 12.9.2005 (1 demi-journée) FrontPage 2003 - niveau 2 : 15 - 16.9.2005 (2 jours) AutoCAD 2005 - niveau 1 : 22, 23, 28, 29.9.2005 (4 jours) MAGNE-05 - Magnétisme pour l'électrotechnique : 27 - 29.9.2005 (3 jours) LabVIEW Application Development (Intermediate I): 5 - 7.12.2005 (3 days) LabVIEW Advanced Programming (Intermediate 2): 8 - 9.12.2005 (2 days) ENSEIGNEMENT TECHNIQUE TECHNICAL TRAINING Monique Duval 74924 technical.training@cern.ch

  7. Technical Training: Places available

    CERN Multimedia

    Monique Duval

    2005-01-01

    The number of places available may vary. Please check our Web site to find out the current availability. Places are available in the following courses: The JAVA Programming Language Level 1: 11 & 12.1.2005 (2 days) Introduction to XML : 13 & 14.1.2005 (2 days) The CERN EDMS for Local Administrators: 19 & 20.1.2005 (2 days - free course) Programmation Unity-Pro pour utilisateurs de Schneider PL7-Pro : 24 - 28.1.2005 (8 demi-journées) LabVIEW base 1/basics 1 : 31.1 - 1.2.2005 (2 j size="2">LabVIEW base 2/basics 2 : 3 & 4.2.2005 (2 jours/2 days - langue à décider/language to be decided) Finite State Machines in the JCOP Framework: 1 - 3.2.2005 (3 days - free course) The JAVA Programming Language Level 2: 7 - 9.2.2005 (3 days) C++ Programming Advanced -Traps and Pitfalls: 8 - 11.2.2005 (4 days) Joint PVSS JCOP Framework: 14 - 18.2.2005 (5 days) JAVA 2 Enterprise Edition - Part 1: ...

  8. Technical Training: Places available

    CERN Multimedia

    Davide Vitè

    2005-01-01

    The number of places available may vary. Please check our Web site to find out the current availability. Places are available on the following courses: Joint PVSS JCOP Framework : 3 - 7.10.2005 (5 days) Utilisation des fichiers PDF avec Acrobat 7.0 :   4.10.2005 (1 journée) LaTeX par la pratique :   4 - 6.10.2005 (3 matinées) PowerPoint 2003 (F) :  7.10.2005 (1 journée) FileMaker - niveau 1 :  20 - 21.10.2005 (2 jours) ACCESS 2003 - Level 1 - ECDL M5: 24 - 25.10.2005 (2 days) Finite State Machines in the JCOP Framework : 25 - 27.10.2005 (3 days) EXCEL 2003 (Short Course III) - HowTo... Pivot tables: 26.10.2005 (morning) WORD 2003 (Short Course I) - HowTo... Work with AutoTasks: 26.10.2005 (afternoon) OUTLOOK (Short Course I) - E-mail: 2.11.2005 (morning) WORD 2003 (Short Course II) - HowTo... Mail merge: 2.11.2005 (afternoon) FrontPage 2003 - niveau 1 :  3 - 4.11.2005 (2 jours) AutoCAD 2006 - niveau 1 : 3, 4, 9, 10.11.2005 (4 jours) Joint PVSS JCO...

  9. Technical Training: Places available

    CERN Multimedia

    Monique Duval

    2004-01-01

    The number of places available may vary. Please check our Web site to find out the current availability. Places are available in the following courses: LabVIEW Intermediate I : 8 - 10.11.2004 (3 days) Instructor-led WTechT Study or Follow-up for Microsoft Applications : 9.11.2004 (morning) Hands-On Object Oriented Design and Programming with C++ : 9 - 11.11.2004 (3 days) Outlook (Short Course III) : Meetings and Delegation : 9.11.2004 (2 hours, afternoon) LabVIEW Intermediate II : 11 & 12.11.2004 (2 days) AutoCAD 2002 - niveau 1 : 11, 12, 18, 19.11.2004 (4 jours) C++ for Particle Physicists : 15 - 19.11.2004 (6 X 3 hours sessions) Word 2003 - niveau 1 : 22 & 23.11.2004 (2 jours) Introduction à ANSYS : 23 - 26.11.2004 (4 jours) CLEAN-2002 - Travailler en salle propre : 23.11.2004 (après-midi, cours gratuit) Project Planning with MS-Project : 25.11 & 2.12.2004 (2 days) PCAD Sch&eac...

  10. Technical Training: Places available

    CERN Multimedia

    Davide Vitè

    2005-01-01

    The number of places available may vary. Please check our Web site to find out the current availability. Places are available on the following courses: FileMaker - niveau 1 :  20 - 21.10.2005 (2 jours) ACCESS 2003 - Level 1 - ECDL M5: 24 - 25.10.2005 (2 days) Finite State Machines in the JCOP Framework : 25 - 27.10.2005 (3 days) EXCEL 2003 (Short Course III) - HowTo... Pivot tables: 26.10.2005 (morning) WORD 2003 (Short Course I) - HowTo... Work with AutoTasks: 26.10.2005 (afternoon) OUTLOOK (Short Course I) - E-mail: 2.11.2005 (morning) WORD 2003 (Short Course II) - HowTo... Mail merge: 2.11.2005 (afternoon) FrontPage 2003 - niveau 1 :  3 - 4.11.2005 (2 jours) AutoCAD 2006 - niveau 1 : 3, 4, 9, 10.11.2005 (4 jours) Joint PVSS JCOP Framework : 7 - 11.11.2005 (5 days) OUTLOOK (Short Course II) - Calendar, Tasks and Notes: 16.11.2005 (morning) Joint PVSS JCOP Framework : 21 - 25.11.2005 (5 days) OUTLOOK (Short Course III) - Meetings and Delegation: 30.11....

  11. Technical Training: Places available

    CERN Multimedia

    Davide Vitè

    2005-01-01

    The number of places available may vary. Please check our Web site to find out the current availability. Places are available on the following courses: FileMaker - niveau 1 :  20 - 21.10.2005 (2 jours) ACCESS 2003 - Level 1 - ECDL M5: 24 - 25.10.2005 (2 days) Finite State Machines in the JCOP Framework : 25 - 27.10.2005 (3 days) EXCEL 2003 (Short Course III) - HowTo... Pivot tables: 26.10.2005 (morning) OUTLOOK (Short Course I) - E-mail: 2.11.2005 (morning) WORD 2003 (Short Course II) - HowTo... Mail merge: 2.11.2005 (afternoon) FrontPage 2003 - niveau 1 :  3 - 4.11.2005 (2 jours) AutoCAD 2006 - niveau 1 : 3, 4, 9, 10.11.2005 (4 jours) Joint PVSS JCOP Framework : 7 - 11.11.2005 (5 days) OUTLOOK (Short Course II) - Calendar, Tasks and Notes: 16.11.2005 (morning) Joint PVSS JCOP Framework : 21 - 25.11.2005 (5 days) OUTLOOK (Short Course III) - Meetings and Delegation: 30.11.2005 (morning) WORD 2003 (Short Course III) - HowTo... Work with long documents : ...

  12. Technical Training: Places available

    CERN Multimedia

    Monique Duval

    2005-01-01

    The number of places available may vary. Please check our Web site to find out the current availability. Places are available on the following courses: FrontPage 2003 - niveau 1 : 1 - 2.9.2005 (2 jours) Utilisation des fichiers PDF avec ACROBAT 7.0 : 5.9.2005 (1 jour) LabVIEW Basics 1:  5 â€" 7.9.2005 (3 days) Introduction à Windows XP au CERN : 12.9.2005 (1 demi-journée) FrontPage 2003 - niveau 2 : 15 - 16.9.2005 (2 jours) AutoCAD 2005 - niveau 1 : 22, 23, 28, 29.9.2005 (4 jours) Finite State Machines in the JCOP Framework:  26 - 28.9.2005 (3 days) MAGNE-05 - Magnétisme pour l'électrotechnique : 27 - 29.9.2005 (3 jours) Joint PVSS JCOP Framework : 3 - 7.10.2005 (5 days) ACCESS 2003 - Level 1 - ECDL M5: 24 - 25.10.2005 (2 days) EXCEL 2003 (Short Course III) - HowTo... Pivot tables: 26.10.2005 (morning) OUTLOOK (Short Course I) - E-mail: 2.11.2005 (morning) OUTLOOK (Short Course II) - Calendar, Tasks and Notes: 16.11.2005 (morning) OU...

  13. Technical Training: Places available

    CERN Multimedia

    Monique Duval

    2004-01-01

    The number of places available may vary. Please check our Web site to find out the current availability. Places are available in the following courses: The JAVA Programming Language Level 1: 11 & 12.1.2005 (2 days) Introduction to XML : 13 & 14.1.2005 (2 days) ELEC-2005.:Winter term: Introduction to electronics in HEP: 18, 20, 25, 27.1, 1 & 3.2.2005 (6 x 2h lectures) The CERN EDMS for Local Administrators: 19 & 20.1.2005 (2 days - free course) Programmation Unity-Pro pour utilisateurs de Schneider PL7-Pro : 24 - 28.1.2005 (8 demi-journées) CLEAN-2002 : Travailler en salle propre : 25.1.2005 (après-midi, cours gratuit) Compatibilité électromagnétique (CEM) : installation et remèdes : 25 - 27.1.2005 (3 jours) Finite State Machines in the JCOP Framework: 1 - 3.2.2005 (3 days - free course) The JAVA Programming Language Level 2: 7 - 9...

  14. Technical Training: Places available

    CERN Multimedia

    Monique Duval

    2005-01-01

    The number of places available may vary. Please check our Web site to find out the current availability. Places are available on the following courses: The CERN EDMS for Local Administrators: 19 & 20.1.2005 (2 days - free course) Programmation Unity-Pro pour utilisateurs de Schneider PL7-Pro : 24 - 28.1.2005 (9 demi-journées) LabVIEW base 1/basics 1 : 31.1 - 2.2.2005 (3 jours/3 days - langue à décider/language to be decided) LabVIEW base 2/basics 2 : 3 & 4.2.2005 (2 jours/2 days - langue à décider/language to be decided) Finite State Machines in the JCOP Framework: 1 - 3.2.2005 (3 days - free course) The JAVA Programming Language Level 2: 7 - 9.2.2005 (3 days) C++ Programming Advanced -Traps and Pitfalls: 8 - 11.2.2005 (4 days) Joint PVSS JCOP Framework: 14 - 18.2.2005 (5 days) JAVA 2 Enterprise Edition - Part 1: WEB Applications: 21 & 22.2.2005 (2 days) JAVA 2 Enterprise Edition - Part 2: Enterprise JavaBeans: 23 - 25.2.2005 (3 days) ELEC-2005 â...

  15. Technical Training: Places available

    CERN Multimedia

    Monique Duval

    2005-01-01

    The number of places available may vary. Please check our Web site to find out the current availability. Places are available on the following courses: LabVIEW base 1/basics 1 : 31.1 - 2.2.2005 (3 jours/3 days - langue à décider/language to be decided) LabVIEW base 2/basics 2 : 3 & 4.2.2005 (2 jours/2 days - langue à décider/language to be decided) Finite State Machines in the JCOP Framework: 1 - 3.2.2005 (3 days - free course) The JAVA Programming Language Level 2: 7 - 9.2.2005 (3 days) C++ Programming Advanced -Traps and Pitfalls: 8 - 11.2.2005 (4 days) Joint PVSS JCOP Framework: 14 - 18.2.2005 (5 days) JAVA 2 Enterprise Edition - Part 1: WEB Applications: 21 & 22.2.2005 (2 days) FrontPage 2003 - niveau 1 : 21 & 22.2.2005 (2 jours) JAVA 2 Enterprise Edition - Part 2: Enterprise JavaBeans: 23 - 25.2.2005 (3 days) ELEC-2005 - Spring Term: Integrated circuits and VLSI technology...

  16. Technical Training: Places available

    CERN Multimedia

    Monique Duval

    2004-01-01

    The number of places available may vary. Please check our Web site to find out the current availability. Places are available in the following courses: Joint PVSS JCOP Framework : 9 - 13.8.2004 (5 days) Outlook (I): E-mail : 31.8.2004 (2 hours, morning) Outlook (II): Calendar, Tasks and Notes : 31.8.2004 (2 hours, afternoon) Hands-on Introduction to Python Programming : 1 - 3.9.2004 (3 days - free course) Instructor-led WBTechT Study or Follow-up for Microsoft Applications : 7.9.2004 (morning) Outlook (III): Meetings and Delegation : 7.9.2004 (2 hours, afternoon) Introduction au VHDL et utilisation du simulateur NCVHDL de CADENCE : 7 & 8.9.2004 (2 jours) Joint PVSS JCOP Framework : 13 - 17.9.2004 (5 days) AutoCAD 2002 - niveau 1 : 13, 14, 23, 24.9.2004 (4 jours) Programmation STEP7 niveau 1 : 14 - 17.9.2004 (4 jours) FrontPage 2003 - niveau 1 : 20 & 21.9.2004 (2 jours) ANSYS: Thermal Analysis : 22 - 24.9.2004 (3 days) ANSYS: Advanced Topics : 27.9...

  17. Technical Training: Places available

    CERN Document Server

    Monique Duval

    2004-01-01

    The number of places available may vary. Please check our Web site to find out the current availability. Places are available in the following courses: Instructor-led WBTechT Study or Follow-up for Microsoft Applications : 7.9.2004 7.9.2004 Outlook (short course III) : Meetings and Delegation : 7.9.2004 (2 hours, afternoon) Introduction au VHDL et utilisation du simulateur NCVHDL de CADENCE : 7 & 8.9.2004 (2 jours) Joint PVSS JCOP Framework : 13 - 17.9.2004 (5 days) Programmation STEP7 niveau 1 : 14-17.9.2004 (4 jours) ANSYS : Thermal Analysis : 22 - 24.9.2004 (3 days) LabVIEW Migration 6 à 7 : 23.9.2004 (one day) ANSYS : Advanced Topics : 27.9 - 1.10.2004 (5 days) Word 2003 - niveau 2 : 27 & 28.9.2004 (2 jours) LabVIEW - Basics 1 : 27 - 29.9.2004 (3 days) MAGNE-04 : Magnétisme pour l'électrotechnique : 28 - 30.9.2004 (3 jours) LabVIEW - Basics 2 : 30.9 & 1.10.2004 (2 days) Introduction à Windows XP au CERN : 4.10.2004 (matin) ...

  18. Technical Training: Places available

    CERN Multimedia

    Monique Duval

    2004-01-01

    The number of places available may vary. Please check our Web site to find out the current availability. Places are available in the following courses: Programmation STEP7 niveau 1 : 14-17.9.2004 (4 jours) ANSYS : Thermal Analysis : 22 - 24.9.2004 (3 days) LabVIEW Migration 6 à 7 : 23.9.2004 (one day) ANSYS : Advanced Topics : 27.9 - 1.10.2004 (5 days) Word 2003 - niveau 2 : 27 & 28.9.2004 (2 jours) LabVIEW - Basics 1 : 27 - 29.9.2004 (3 days) MAGNE-04 : Magnétisme pour l'électrotechnique : 28 - 30.9.2004 (3 jours) LabVIEW - Basics 2 : 30.9 & 1.10.2004 (2 days) Introduction à Windows XP au CERN : 4.10.2004 (matin) FrontPage 2003 - niveau 1 : 7 & 8.10.04 (2 jours) Outlook (short course I) : E-mail : 22.10.2004 (2 hours, morning) Outlook (short course II) : Calendar, Tasks and Notes: 22.10.2004 (2 hours, afternoon) Introduction à ANSYS : 23 - 26.11.2004 (4 jours) ENSEIGNEMENT TECHNIQUE TECHNICAL TRAINING Monique Duval 74924...

  19. Technical Training: Places available

    CERN Multimedia

    Monique Duval

    2005-01-01

    The number of places available may vary. Please check our Web site to find out the current availability. Places are available on the following courses: Hands-on Introduction to Python Programming: 28 - 30.6.2005 (3 days) Introduction to ANSYS: 21 - 24.6.2005 (4 days) IT3T/3 - Working remotely with Windows XP: 28.6.2005 (IT Technical Training Tutorial, free of charge) IT3T/4 - Editing Websites with Frontpage 2003: 30.6.2005 (IT Technical Training Tutorial, free of charge) Utilisation des fichiers PDF avec ACROBAT 7.0 : 5.7.2005 (1 jour) FrontPage 2003 - niveau 1 : 6-7.7.2005 (2 jours) LabVIEW base 1 : 4 - 6.7.2005 (3 jours) LabVIEW Basics 2: 7 - 8.7.2005 (2 days) WORD 2003 (Short Course I) - HowTo... Work with repetitive tasks /AutoText, AutoFormat, AutoCorrect, Find/Replace) : 4.7.2005 (afternoon) WORD 2003 (Short Course II) - HowTo... Mail merge: 5.7.2005 (afternoon) WORD 2003 (Short Course III) - HowTo (4 mornings) EXCEL 2003 (Short Course I) - HowTo... Work ...

  20. Technical Training: Places available

    CERN Multimedia

    Monique Duval

    2004-01-01

    If you wish to participate in one of the following courses, please discuss with your supervisor and apply electronically directly from the course description pages that can be found on the Web at: http://www.cern.ch/Training/ or fill in an 'application for training' form available from your Divisional Secretariat or from your DTO (Divisional Training Officer). Applications will be accepted in the order of their receipt. The number of places available may vary. Please check our Web site to find out the current availability. Places are available in the following courses: Oracle 9i : New features for developers : 14 - 16.6.2004 (3 days) The Joint PVSS JCOP Framework: 14 - 18.6.2004 (5 days) Introduction au VHDL et utilisation du simulateur NCVHDL de CADENCE : 15 & 16.6.2004 (2 jours) EXCEL 2003 - niveau 2 : 17 & 18.6.2004 (2 jours) MAGNE-04 : Magnétisme pour l'électrotechnique : 6 au 8.7.2004 (3 jours) AutoCAD 2002 - niveau 1 : 13, 14, 23, 24.09.2004 (4 jours) ENSEIGNEMEN...

  1. Technical Training: Places Available

    CERN Multimedia

    Monique Duval

    2004-01-01

    If you wish to participate in one of the following courses, please discuss with your supervisor and apply electronically directly from the course description pages that can be found on the Web at: http://www.cern.ch/Training/ or fill in an 'application for training' form available from your Divisional Secretariat or from your DTO (Divisional Training Officer). Applications will be accepted in the order of their receipt. Technical Training Monique Duval - Tel.74924 technical.training@cern.ch The number of places available may vary. Please check our Web site to find out the current availability. Places are available in the following courses: Oracle 9i: SQL: 17 - 19.5.2004 (3 days) Word 2003 - niveau 2 : 24 & 25.5.2004 (2 jours) EXCEL 2003 - niveau 1 : 27 & 28.5.2004 (2 jours) STEP7 Programming Level 1: 1 - 4.6.2004 (4 days) Oracle 9i : Programming with PL/SQL: 2 - 4.6.2004 (3 days) CST Microwave Studio: 3 & 4.6.2004 (2 days) Oracle 9i : New f...

  2. Technical Training: Places available

    CERN Multimedia

    Monique Duval

    2004-01-01

    If you wish to participate in one of the following courses, please discuss with your supervisor and apply electronically directly from the course description pages that can be found on the Web at: http://www.cern.ch/Training/ or fill in an 'application for training' form available from your Divisional Secretariat or from your DTO (Divisional Training Officer). Applications will be accepted in the order of their receipt. Technical Training Monique Duval - Tel.74924 technical.training@cern.ch The number of places available may vary. Please check our Web site to find out the current availability. Places are available in the following courses: Word 2003 - niveau 2 : 24 & 25.5.2004 (2 jours) VisualEliteHDL : 25 & 26.5.2004 (2 days) EXCEL 2003 - niveau 1 : 27 & 28.5.2004 (2 jours) STEP7 Programming Level 1: 1 - 4.6.2004 (4 days) Oracle 9i : Programming with PL/SQL: 2 - 4.6.2004 (3 days) CST Microwave Studio: 3 & 4.6.2004 (2 days) Oracle 9...

  3. Technical Training: Places available

    CERN Multimedia

    Monique Duval

    2005-01-01

    The number of places available may vary. Please check our Web site to find out the current availability. Places are available on the following courses: Utilisation des fichiers PDF avec ACROBAT 6.0 : 1.3.2005 (1 journée) ELEC-2005 - Spring Term: Integrated circuits and VLSI technology for physics: 1 - 17.3.2005 (6 x 2.5-hour lectures) C++ for Particle Physicists: 7 - 11.3.2005 (6 x 3-hour lectures) Joint PVSS JCOP Framework : 14 - 18.3.2005 (5 days) AXEL-2005; Introduction to Particle Accelerators : 14- 18.3.2005 (10 x 1 h lectures) ACCESS 2003 - Level 1: ECDL M5: 15 - 16.3.2005 (2 days) AutoCAD 2002 - niveau 1 : 15, 16, 21& 22.3.2005 (4 jours) FrontPage 2003 - niveau 2 : 21 & 22.3.2005 (2 jours) Hands-on Object-Oriented Design and Programming with C++ : 22 - 24.3.2005 (3 days) FileMaker - niveau 2 : 4 & 5.4.2005 (2 jours) EXCEL 2003 - niveau 2 : 11 & 12.4.2005 (2 jours) LabVIEW Intermediate 1: 11 - 13.4.2005...

  4. Technical Training: Places available

    CERN Multimedia

    Monique Duval

    2005-01-01

    The number of places available may vary. Please check our Web site to find out the current availability. Places are available on the following courses: JAVA 2 Enterprise Edition - Part 1: WEB Applications: 21 & 22.2.2005 (2 days) FrontPage 2003 - niveau 1 : 21 & 22.2.2005 (2 jours) JAVA 2 Enterprise Edition - Part 2: Enterprise JavaBeans: 23 - 25.2.2005 (3 days) Utilisation des fichiers PDF avec ACROBAT 6.0 : 1.3.2005 (1 journée) Hands-on Object-Oriented Design and Programming with C++ : 1 - 3.3.2005 (3 days) ELEC-2005 - Spring Term: Integrated circuits and VLSI technology for physics: 1 - 17.3.2005 (6 x 2.5-hour lectures) C++ for Particle Physicists: 7 - 11.3.2005 (6 x 3-hour lectures) Joint PVSS JCOP Framework : 14 - 18.3.2005 (5 days) ACCESS 2003 - Level 1 : 15 - 16.3.2005 (2 days) AutoCAD 2002 - niveau 1 : 15, 16, 21& 22.3.2005 (4 jours) FrontPage 2003 - niveau 2 : 21 & 22.3.2005 (2 jours) FileMaker - ...

  5. THE PLACES FOR PARTICIPATION

    Directory of Open Access Journals (Sweden)

    Tania Carson

    2007-09-01

    Full Text Available The current upsurge of interest in street art with its direct approach to the city emphasizes the need to readdress public arts’ role within the wider social and cultural context. As it becomes routine to incorporate art works into city planning and city life, art has become both ‘safe’ and ‘user‐friendly’. On the one hand, art is subsumed and immersed into the wider culture through leisure and entertainment policies, socially engaged public art projects, community art and urban design. On the other hand, there are those works which deliberately intend to unsettle or confront the viewer. In recent years the term intervention has been ascribed to unorthodox art works in the public sphere which are often illicit, or at least non‐complicit in the prevailing hegemony. These practices are disruptive due to their enactment outside traditional art spaces, often in the streets. By occupying the streets, places of democracy and disjunction, these interventions transform public space back into a place of overt cultural and political expression. They also deliberately involve the inhabitants of the city by utilizing everyday spaces in ways which offer an unmediated sense of the artwork.

  6. Technical Training: Places available

    CERN Multimedia

    Monique Duval

    2005-01-01

    The number of places available may vary. Please check our Web site to find out the current availability. Places are available on the following courses: FrontPage 2003 - niveau 1 : 9 & 10.5.2005 (2 jours) ELEC-2005 - Summer Term: System electronics for physics - Issues : 10, 12, 17, 19, 24, 26 & 31.5.2005 (7 x 2h lectures) AutoCAD 2005 - niveau 1 : 12, 13, 18, 19.5.2005 (4 jours) ACCESS 2003 - Level 1: ECDL M5 : 11 & 12.5.2005 (2 days) Object-Oriented Analysis and Design using UML: 17 - 19.5.2005 (3 days) Synplify Pro Training: 18.5.2005 (1 day) Finite State Machines in the JCOP Framework: 24 - 26.5.2005 (3 days) The Joint PVSS JCOP Framework: 30.5 - 3.6.2005 (5 days) Introduction à la CAO CADENCE : 31.5 - 1.6.2005 (2 jours) LabVIEW Real-Time (F) : 7 - 9.6.2005 (3 jours) LabVIEW Migration 6 to 7: 14.6.2005 (1 day) FrontPage 2003 - niveau 2 : 16 & 17.6.2005 (2 jours) Utilisation de fichiers PDF avec ACROBAT 6.0 : 20.6.2005 (1journée) Intr...

  7. Technical Training: Places available

    CERN Multimedia

    Monique Duval

    2005-01-01

    The number of places available may vary. Please check our Web site to find out the current availability. Places are available on the following courses: FrontPage 2003 - niveau 1 : 9 & 10.5.2005 (2 jours) ELEC-2005 - Summer Term: System electronics for physics - Issues : 10, 12, 17, 19, 24, 26 & 31.5.2005 (7 x 2h lectures) AutoCAD 2005 - niveau 1 : 11, 12, 18, 19.5.2005 (4 jours) Object-Oriented Analysis and Design using UML: 17 - 19.5.2005 (3 days) Synplify Pro Training: 18.5.2005 (1 day) Finite State Machines in the JCOP Framework: 24 - 26.5.2005 (3 days) The Joint PVSS JCOP Framework: 30.5 - 3.6.2005 (5 days) Introduction à la CAO CADENCE : 31.5 - 1.6.2005 (2 jours) LabVIEW Real-Time (F) : 7 - 9.6.2005 (3 jours) LabVIEW Migration 6 to 7: 14.6.2005 (1 day) FrontPage 2003 - niveau 2 : 16 & 17.6.2005 (2 jours) Utilisation de fichiers PDF avec ACROBAT 6.0 : 20.6.2005 (1journée) Introductio...

  8. Technical Training: Places available

    CERN Multimedia

    Davide Vitè

    2005-01-01

    The number of places available may vary. Please check our Web site to find out the current availability. Places are available on the following courses: The Java Programming Language Level 1: 21 - 23.11.2005 (3 days) OUTLOOK (Short Course III) - Meetings and Delegation: 30.11.2005 (morning) WORD 2003 (Short Course III) - HowTo... Work with long documents : 30.11.2005 (afternoon) FrontPage 2003 - niveau 2 : 5 - 6.12.2005 (2 jours) Introduction à ANSYS Classique : 6 - 9.12.2005 (4 jours) EXCEL 2003 (Short Course II) - HowTo... Format your worksheet for printing: 7.12.2005 (morning) PCAD Schémas - Introduction : 8 - 9.12.2005 (2 jours) ACCESS 2003 - Level 2 - ECDL AM5: 14 - 15.12.2005 (2 days) LabVIEW Basics I:  23 - 25.1.2006 (3 days) C++ Programming Advanced - Traps and Pitfalls: 24 - 27.1.2006 (4 days) LabVIEW Basics II:  26 - 27.1.2006 (2 days) Joint PVSS-JCOP Framework: 30.1 - 3.2.2006 (5 days, free of charge) Finite State Machines in the JCOP Framework : ...

  9. Technical Training: Places available

    CERN Multimedia

    Davide Vitè

    2005-01-01

    The number of places available may vary. Please check our Web site to find out the current availability. Places are available on the following courses: FrontPage 2003 - niveau 2 : 5 - 6.12.2005 (2 jours) Introduction à ANSYS Classique : 6 - 9.12.2005 (4 jours) EXCEL 2003 (Short Course II) - HowTo... Format your worksheet for printing: 7.12.2005 (morning) PCAD Schémas - Introduction : 8 - 9.12.2005 (2 jours) Finite State Machines in the JCOP Framework: 13 - 15.12.2005 (3 days) ACCESS 2003 - Level 2 - ECDL AM5: 14 - 15.12.2005 (2 days) PCAD PCB - Introduction : 14 - 16.12.2005 (3 jours) AutoCAD 2006 - niveau 1 : 19, 20, 24 & 25.1.2006 (4 jours) LabVIEW Basics I:  23 - 25.1.2006 (3 days) C++ Programming Advanced - Traps and Pitfalls: 24 - 27.1.2006 (4 days) STEP7 Programming Level 1: 24 - 27.1.2006 (4 days) LabVIEW Basics II:  26 - 27.1.2006 (2 days) AutoCAD Mechanical 2006 : 30 - 31.1.2006 (2 jours; suite du cours AutoCAD 2006 - niveau 1) Joint PVS...

  10. Technical Training: Places available

    CERN Multimedia

    Davide Vitè

    2005-01-01

    The number of places available may vary. Please check our Web site to find out the current availability. Places are available on the following courses: ACCESS 2003 - Level 1 - ECDL M5: 24 - 25.10.2005 (2 days) Finite State Machines in the JCOP Framework : 25 - 27.10.2005 (3 days) EXCEL 2003 (Short Course III) - HowTo... Pivot tables: 26.10.2005 (morning) Introduction to the CERN EDMS: 2.11.2005 (1 day, free of charge) OUTLOOK (Short Course I) - E-mail: 2.11.2005 (morning) WORD 2003 (Short Course II) - HowTo... Mail merge: 2.11.2005 (afternoon) FrontPage 2003 - niveau 1 :  3 - 4.11.2005 (2 jours) AutoCAD 2006 - niveau 1 : 3, 4, 9, 10.11.2005 (4 jours) Joint PVSS JCOP Framework : 7 - 11.11.2005 (5 days) The CERN EDMS for Engineers: 8.11.2005 (1 day, free of charge) The EDMS-MTF in practice: 9.11.2005 (morning, free of charge) The CERN EDMS for Local Administrators: 15-16.11.2005 (2 days, free of charge) OUTLOOK (Short Course II) - Calendar, Tasks and Notes: ...

  11. Technical Training: Places available

    CERN Multimedia

    Davide Vitè

    2005-01-01

    The number of places available may vary. Please check our Web site to find out the current availability. Places are available on the following courses: OUTLOOK (Short Course III) - Meetings and Delegation: 30.11.2005 (morning) WORD 2003 (Short Course III) - HowTo... Work with long documents: 30.11.2005 (afternoon) FrontPage 2003 - niveau 2 : 5 - 6.12.2005 (2 jours) Introduction à ANSYS Classique : 6 - 9.12.2005 (4 jours) EXCEL 2003 (Short Course II) - HowTo... Format your worksheet for printing: 7.12.2005 (morning) AutoCAD - mise à jour d’AutoCAD 2002 à AutoCAD 2006 : 8.12.2005 (1 journée - pour les utilisateurs d’AutoCAD 2002) PCAD Schémas - Introduction : 8 - 9.12.2005 (2 jours) Finite State Machines in the JCOP Framework: 13 - 15.12.2005 (3 days) PCAD PCB - Introduction : 14 - 16.12.2005 (3 jours) ACCESS 2003 - Level 2 - ECDL AM5: 14 - 15.12.2005 (2 days) AutoCAD 2006 - niveau 1 : 19, 20, 24 & 25.1.2006 (4 jours) LabVIEW Basics I:  23 - 25.1.2006...

  12. TECHNICAL TRAINING: PLACES AVAILABLE

    CERN Multimedia

    Monique Duval

    2004-01-01

    The number of places available may vary. Please check our Web site to find out the current availability. Places are available in the following courses: LabVIEW Basics 1 : 22 - 24.3.2004 (3 days) Oracle 9i : New Features for Developers : 22 - 24.3.2004 (3 days) Instructor-led WBTechT study or follow-up for Microsoft applications : 1.4.2004 (morning) FrontPage XP - niveau 1 : 5 & 6.4.2004 (2 jours) AutoCAD 2002 - niveau 1 : 19, 20.4 et 3, 4.5.2004 (4 jours) Oracle 8i/9i - Develop Web-based Applications with PL/SQL : 19 & 20.4.2004 (2 days) Introduction to ANSYS : 20 - 23.4.2004 (4 days) LabVIEW hands-on (E) : 20.4.2004 (afternoon, free of charge) FrontPage XP - niveau 2 : 26 & 27.4.2004 (2 jours) LabVIEW Base 2 : 6 & 7.5.2004 (2 jours) Word XP - niveau 1 : 10 & 11.5.2004 (2 jours) Word XP - niveau 2 : 24 & 25.5.2004 (2 jours) If you wish to participate in one of these courses, pleas...

  13. Technical Training: Places available

    CERN Multimedia

    2004-01-01

    If you wish to participate in one of the following courses, please discuss with your supervisor and apply electronically directly from the course description pages that can be found on the Web at: http://www.cern.ch/Training/ or fill in an "application for training" form available from your Divisional Secretariat or from your DTO (Divisional Training Officer). Applications will be accepted in the order of their receipt. TECHNICAL TRAINING Monique Duval tel. 74924 technical.training@cern.ch The number of places available may vary. Please check our Web site to find out the current availability. Places are available in the following courses: Instructor-led WBTechT study or follow-up for Microsoft applications : 1.4.2004 (morning) FrontPage XP - niveau 1 : 5 & 6.4.2004 (2 jours) AutoCAD 2002 - niveau 1 : 19, 20.4 et 3, 4.5.2004 (4 jours) Oracle 8i/9i - Develop Web-based Applications with PL/SQL : 19 & 20.4.2004 (2 days) Introduction to ANSYS : 20 - 23.4.2004 (4 day...

  14. Technical Training: Places available

    CERN Multimedia

    Monique Duval

    2005-01-01

    The number of places available may vary. Please check our Web site to find out the current availability. Places are available on the following courses: JAVA 2 Enterprise Edition - Part 1: WEB Applications: 21 & 22.2.2005 (2 days) FrontPage 2003 - niveau 1 : 21 & 22.2.2005 (2 jours) JAVA 2 Enterprise Edition - Part 2: Enterprise JavaBeans: 23 - 25.2.2005 (3 days) Utilisation des fichiers PDF avec ACROBAT 6.0 : 1.3.2005 (1 journée) ELEC-2005 - Spring Term: Integrated circuits and VLSI technology for physics: 1 - 17.3.2005 (6 X 2.30-hours lectures) C++ for Particle Physicists: 7 - 11.3.2005 (6 X 3-hour lectures) Joint PVSS JCOP Framework : 14 - 18.3.2005 (5 days) AutoCAD 2002 - niveau 1 : 15, 16, 21& 22.3.2005 (4 jours) FrontPage 2003 - niveau 2 : 21 & 22.3.2005 (2 jours) FileMaker - niveau 2 : 4 & 5.4.2005 (2 jours) EXCEL 2003 - niveau 2 : 11 & 12.4.2005 (2 jours) LabVIEW intermediate 1: 11 - 13....

  15. Technical Training: Places available

    CERN Multimedia

    Monique Duval

    2005-01-01

    The number of places available may vary. Please check our Web site to find out the current availability. Places are available on the following courses: LabVIEW base 2/basics 2 : 3 & 4.2.2005 (2 jours/2 days - langue à décider/language to be decided) Finite State Machines in the JCOP Framework: 1 - 3.2.2005 (3 days - free course) The JAVA Programming Language Level 2: 7 - 9.2.2005 (3 days) JAVA 2 Enterprise Edition - Part 1: WEB Applications: 21 & 22.2.2005 (2 days) FrontPage 2003 - niveau 1 : 21 & 22.2.2005 (2 jours) JAVA 2 Enterprise Edition - Part 2: Enterprise JavaBeans: 23 - 25.2.2005 (3 days) ELEC-2005 - Spring Term: Integrated circuits and VLSI technology for physics: 1 - 17.3.2005 (6 X 2.30-hours lectures) C++ for Particle Physicists: 7 - 11.3.2005 (6 X 3-hour lectures) Joint PVSS JCOP Framework : 14 - 18.3.2005 (5 days) AutoCAD 2002 - niveau 1 : 15, 16, 21& 22.3.2005 (4 jours) FrontPage 20...

  16. Technical Training: Places available

    CERN Multimedia

    Monique Duval

    2005-01-01

    The number of places available may vary. Please check our Web site to find out the current availability. Places are available on the following courses: ELEC-2005 - Spring Term: Integrated circuits and VLSI technology for physics: 1 - 17.3.2005 (6 x 2.5-hour lectures) C++ for Particle Physicists: 7 - 11.3.2005 (6 x 3-hour lectures) Joint PVSS JCOP Framework : 14 - 18.3.2005 (5 days) Oracle 9i: SQL: 14 -16.3.2005 (3 days) AXEL-2005; Introduction to Particle Accelerators : 14- 18.3.2005 (10 x 1 h lectures) ACCESS 2003 - Level 1: ECDL M5: 15 - 16.3.2005 (2 days) AutoCAD 2002 - niveau 1 : 15, 16, 21& 22.3.2005 (4 jours) FrontPage 2003 - niveau 2 : 21 & 22.3.2005 (2 jours) Hands-on Object-Oriented Design and Programming with C++ : 22 - 24.3.2005 (3 days) FileMaker - niveau 2 : 4 & 5.4.2005 (2 jours) Oracle 9i: Programming with PL/SQL: 4 - 6.4.2005 (3 days) EXCEL 2003 - niveau 2 : 11 & 12.4.2005 (2 jours) LabVIEW Intermedia...

  17. Technical Training: Places available

    CERN Multimedia

    2004-01-01

    If you wish to participate in one of the following courses, please discuss with your supervisor and apply electronically directly from the course description pages that can be found on the Web at: http://www.cern.ch/Training/ or fill in an "application for training" form available from your Divisional Secretariat or from your DTO (Divisional Training Officer). Applications will be accepted in the order of their receipt. TECHNICAL TRAINING Monique Duval tel. 74924 technical.training@cern.ch The number of places available may vary. Please check our Web site to find out the current availability. Places are available in the following courses: FrontPage XP - niveau 2 : 26 & 27.4.2004 (2 jours) The Joint PVSS JCOP Framework : 26 - 30.4.2004 (5 days) Computational Electromagnetics with the ELEKTRA Module of OPERA-3D : 27 & 28.4.2004 (2 days) Hands-on Introduction to Python Programming : 3 - 5.5.2004 (3 days) LabVIEW Base 2 : 6 & 7.5.2004 (2 jours) Project Pla...

  18. Technical Training: Places available

    CERN Multimedia

    2004-01-01

    If you wish to participate in one of the following courses, please discuss with your supervisor and apply electronically directly from the course description pages that can be found on the Web at: http://www.cern.ch/Training/ or fill in an "application for training" form available from your Divisional Secretariat or from your DTO (Divisional Training Officer). Applications will be accepted in the order of their receipt. TECHNICAL TRAINING Monique Duval tel. 74924 technical.training@cern.ch The number of places available may vary. Please check our Web site to find out the current availability. Places are available in the following courses: Computational Electromagnetics with the ELEKTRA Module of OPERA-3D : 27 & 28.4.2004 (2 days) Hands-on Introduction to Python Programming : 3 - 5.5.2004 (3 days) LabVIEW Base 2 : 6 & 7.5.2004 (2 jours) Project Planning with MS-Project : 6 & 13.5.2004 (2 days) Word 2003 - niveau 1 : 10 & 11.5.2004 (2 jours) Oracle 9i : SQL : 10 - 12.5.2004 (3...

  19. Technical Training: Places available

    CERN Multimedia

    2004-01-01

    If you wish to participate in one of the following courses, please discuss with your supervisor and apply electronically directly from the course description pages that can be found on the Web at: http://www.cern.ch/Training/ or fill in an "application for training" form available from your Divisional Secretariat or from your DTO (Divisional Training Officer). Applications will be accepted in the order of their receipt. TECHNICAL TRAINING Monique Duval tel. 74924 technical.training@cern.ch The number of places available may vary. Please check our Web site to find out the current availability. Places are available in the following courses: AutoCAD 2002 - niveau 1 : 19, 20.4 et 3, 4.5.2004 (4 jours) Oracle 8i/9i - Develop Web-based Applications with PL/SQL : 19 & 20.4.2004 (2 days) Introduction to ANSYS : 20 - 23.4.2004 (4 days) LabVIEW Hands-on : 20.4.2004 (half-day, p.m.) FrontPage XP - niveau 2 : 26 & 27.4.2004 (2 jours) The Joint PVSS JCOP Framework : 26 -...

  20. Technical Training: Places available

    CERN Multimedia

    Monique Duval

    2004-01-01

    The number of places available may vary. Please check our Web site to find out the current availability. Places are available in the following courses: The CERN EDMS for Engineers : 6.10.2004 (1 day) FileMaker - niveau 1 : 18 & 19.10.2004 (2 jours) Outlook (short course I) : E-mail : 22.10.2004 (2 hours, morning) Outlook (short course II) : Calendar, Tasks and Notes: 22.10.2004 (2 hours, afternoon) Excel 2003 - niveau 1 : 4 & 5.11.2004 (2 jours) LabVIEW Intermediate I : 8 - 10.11.2004 (3 days) Instructor-led WTechT Study or Follow-up for Microsoft Applications : 9.11.2004 (morning) Hands-On Object Oriented Design and Programming with C++ : 9 - 11.11.2004 (3 days) Outlook (Short Course III) : Meetings and Delegation : 9.11.2004 (2 hours, afternoon) LabVIEW Intermediate II : 11 & 12.11.2004 (2 days) AutoCAD 2002 - niveau 1 : 11, 12, 18, 19.11.2004 (4 jours) C++ for Particle Physicists : 15 - 19.11.2004 (6 X 3 hours sessions...

  1. Technical Training: Places available

    CERN Multimedia

    Monique Duval

    2004-01-01

    The number of places available may vary. Please check our Web site to find out the current availability. Places are available in the following courses: LabVIEW - Basics 2 : 30.9 & 1.10.2004 (2 days) Introduction à Windows XP au CERN : 4.10.2004 (matin) The EDMS MTF in practice : 4.10.2004 (afternoon) The CERN EDMS for Engineers : 6.10.2004 (1 day) FrontPage 2003 - niveau 1 : 7 & 8.10.04 (2 jours) Hands-On Object Oriented Design and Programming with C++ : 9 - 12.11.2004 (3 days) FileMaker - niveau 1 : 18 & 19.10.2004 (2 jours) Outlook (short course I) : E-mail : 22.10.2004 (2 hours, morning) Outlook (short course II) : Calendar, Tasks and Notes: 22.10.2004 (2 hours, afternoon) Excel 2003 - niveau 1 : 4 & 5.11.2004 (2 jours) Instructor-led WTechT Study or Follow-up for Microsoft Applications : 9.11.2004 (morning) Outlook (Short Course III) : Meetings and Delegation : 9.11...

  2. Technical Training: Places available

    CERN Multimedia

    Monique Duval

    2004-01-01

    The number of places available may vary. Please check our Web site to find out the current availability. Places are available in the following courses: FileMaker - niveau 1 : 18 & 19.10.2004 (2 jours) Outlook (short course I) : E-mail : 22.10.2004 (2 hours, morning) Outlook (short course II) : Calendar, Tasks and Notes: 22.10.2004 (2 hours, afternoon) Excel 2003 - niveau 1 : 4 & 5.11.2004 (2 jours) LabVIEW Intermediate I : 8 - 10.11.2004 (3 days) Instructor-led WTechT Study or Follow-up for Microsoft Applications : 9.11.2004 (morning) Hands-On Object Oriented Design and Programming with C++ : 9 - 11.11.2004 (3 days) Outlook (Short Course III) : Meetings and Delegation : 9.11.2004 (2 hours, afternoon) LabVIEW Intermediate II : 11 & 12.11.2004 (2 days) AutoCAD 2002 - niveau 1 : 11, 12, 18, 19.11.2004 (4 jours) C++ for Particle Physicists : 15 - 19.11.2004 (6 X 3 hours sessions) FrontPage 2003 - niveau 2 : 18 &a...

  3. Technical Training: Places available

    CERN Multimedia

    Monique Duval

    2004-01-01

    The number of places available may vary. Please check our Web site to find out the current availability. Places are available in the following courses: Outlook (short course I) : E-mail : 22.10.2004 (2 hours, morning) Outlook (short course II) : Calendar, Tasks and Notes: 22.10.2004 (2 hours, afternoon) Excel 2003 - niveau 1 : 4 & 5.11.2004 (2 jours) LabVIEW Intermediate I : 8 - 10.11.2004 (3 days) Instructor-led WTechT Study or Follow-up for Microsoft Applications : 9.11.2004 (morning) Hands-On Object Oriented Design and Programming with C++ : 9 - 11.11.2004 (3 days) Outlook (Short Course III) : Meetings and Delegation : 9.11.2004 (2 hours, afternoon) LabVIEW Intermediate II : 11 & 12.11.2004 (2 days) AutoCAD 2002 - niveau 1 : 11, 12, 18, 19.11.2004 (4 jours) C++ for Particle Physicists : 15 - 19.11.2004 (6 X 3 hours sessions) FrontPage 2003 - niveau 2 : 18 & 19.11.2004 (2 jours) Word 2003 - niveau 1 : 22 &a...

  4. TECHNICAL TRAINING: Places available**

    CERN Multimedia

    2003-01-01

    If you wish to participate in one of the following courses, please discuss with your supervisor and apply electronically directly from the course description pages that can be found on the Web at: http://www.cern.ch/Training/ or fill in an "application for training" form available from your Divisional Secretariat or from your DTO (Divisional Training Officer). Applications will be accepted in the order of their receipt. TECHNICAL TRAINING Monique Duval tel. 74924 technical.training@cern.ch ** The number of places available may vary. Please check our Web site to find out the current availability. Places are available in the following courses: Hands-on Introduction to Python Programming : 12 - 14.11.03(3 days) ACCESS 2000 - niveau 1 : 13 & 14.11.03 (2 jours) C++ for Particle Physicists : 17 - 21.11.03 (6 X 3-hour lectures) Programmation automate Schneider TSX Premium - niveau 2 : 18 - 21.11.03 (4 jours) Project Planning with MS-Project  (free of charg...

  5. TECHNICAL TRAINING: Places available**

    CERN Multimedia

    2003-01-01

    If you wish to participate in one of the following courses, please discuss with your supervisor and apply electronically directly from the course description pages that can be found on the Web at: http://www.cern.ch/Training/ or fill in an "application for training" form available from your Divisional Secretariat or from your DTO (Divisional Training Officer). Applications will be accepted in the order of their receipt. TECHNICAL TRAINING Monique Duval Tel. 74924 technical.training@cern.ch ** The number of places available may vary. Please check our Web site to find out the current availability. Places are available in the following courses: The EDMS-MTF in practice (free of charge) : 28 -  30.10.03 (6 half-day sessions) AutoCAD 2002 – Level 1 : 3, 4, 12, 13.11.03 (4 days) LabVIEW TestStand ver. 3 : 4 & 5.11.03 (2 days) Introduction to PSpice : 4.11.03 p.m. (half-day) Hands-on Introduction to Python Programming : 12 – 14.11.03 (3 days) ACCESS ...

  6. Technical Training: Places available

    CERN Multimedia

    Davide Vitè

    2005-01-01

    The number of places available may vary. Please check our Web site to find out the current availability. Places are available on the following courses: ELEC-2005 Autumn Term - Electronics applications in HEP experiments: 8.11 - 8.12.2005 (10 x 2h lectures) The CERN EDMS for Local Administrators: 15-16.11.2005 (2 days, free of charge) OUTLOOK (Short Course II) - Calendar, Tasks and Notes: 16.11.2005 (morning) Hands-On Object Oriented Design and Programming with C++ : 16 - 18.11.2005 (3 days) The CERN EDMS for Engineers: 17.11.2005 (1 day, free of charge) The Java Programming Language Level 1: 21 - 23.11.2005 (3 days) Hands-on Introduction to Python Programming: 28 - 30.11.2005 (3 days) OUTLOOK (Short Course III) - Meetings and Delegation: 30.11.2005 (morning) WORD 2003 (Short Course III) - HowTo... Work with long documents : 30.11.2005 (afternoon) FrontPage 2003 - niveau 2 : 5 - 6.12.2005 (2 jours) LabVIEW Application Development (Intermediate 1): 5 - 7.12.2005 (3 d...

  7. Technical Training: Places available

    CERN Multimedia

    Davide Vitè

    2005-01-01

    The number of places available may vary. Please check our Web site to find out the current availability. Places are available on the following courses: Joint PVSS JCOP Framework : 7 - 11.11.2005 (5 days) ELEC-2005 Autumn Term - Electronics applications in HEP experiments: 8.11 - 8.12.2005 (10 x 2h lectures) The EDMS-MTF in practice: 9.11.2005 (morning, free of charge) The CERN EDMS for Local Administrators: 15-16.11.2005 (2 days, free of charge) OUTLOOK (Short Course II) - Calendar, Tasks and Notes: 16.11.2005 (morning) Hands-On Object Oriented Design and Programming with C++ : 16 - 18.11.2005 (3 days) The CERN EDMS for Engineers: 17.11.2005 (1 day, free of charge) The Java Programming Language Level 1: 21 - 23.11.2005 (3 days) Hands-on Introduction to Python Programming: 28 - 30.11.2005 (3 days) OUTLOOK (Short Course III) - Meetings and Delegation: 30.11.2005 (morning) WORD 2003 (Short Course III) - HowTo... Work with long documents : 30.11.2005 (afternoon) Fron...

  8. Technical training: places available

    CERN Multimedia

    Davide Vitè

    2005-01-01

    The number of places available may vary. Please check our Web site to find out the current availability. Places are available on the following courses: Introduction to the CERN EDMS: 2.11.2005 (1 day, free of charge) OUTLOOK (Short Course I) - E-mail: 2.11.2005 (morning) WORD 2003 (Short Course II) - HowTo... Mail merge: 2.11.2005 (afternoon) FrontPage 2003 - niveau 1 :  3 - 4.11.2005 (2 jours) AutoCAD 2006 - niveau 1 : 3, 4, 9, 10.11.2005 (4 jours) Joint PVSS JCOP Framework : 7 - 11.11.2005 (5 days) The CERN EDMS for Engineers: 8.11.2005 (1 day, free of charge) The EDMS-MTF in practice: 9.11.2005 (morning, free of charge) The CERN EDMS for Local Administrators: 15-16.11.2005 (2 days, free of charge) OUTLOOK (Short Course II) - Calendar, Tasks and Notes: 16.11.2005 (morning) Hands-On Object Oriented Design and Programming with C++ : 16 - 18.11.2005 (3 days) The Java Programming Language Level 1: 21 - 23.11.2005 (3 days) Hands-on Introduction to Python Prog...

  9. Wind energy program overview

    International Nuclear Information System (INIS)

    1992-02-01

    This overview emphasizes the amount of electric power that could be provided by wind power rather than traditional fossil fuels. New wind power markets, advances in technology, technology transfer, and wind resources are some topics covered in this publication

  10. Model of analysis of maximum loads in wind generators produced by extreme winds

    International Nuclear Information System (INIS)

    Herrera – Sánchez, Omar; Schellong, Wolfgang; González – Fernández, Vladimir

    2010-01-01

    The use of the wind energy by means of the wind turbines in areas of high risk of occurrence of Hurricanes comes being an important challenge for the designers of wind farm at world for some years. The wind generator is not usually designed to support this type of phenomena, for this reason the areas of high incidence of tropical hurricanes of the planning are excluded, that which, in occasions disables the use of this renewable source of energy totally, either because the country is very small, or because it coincides the area of more potential fully with that of high risk. To counteract this situation, a model of analysis of maxims loads has been elaborated taken place the extreme winds in wind turbines of great behavior. This model has the advantage of determining, in a chosen place, for the installation of a wind farm, the micro-areas with higher risk of wind loads above the acceptable for the standard classes of wind turbines. (author)

  11. Modelling Wind for Wind Farm Layout Optimization Using Joint Distribution of Wind Speed and Wind Direction

    OpenAIRE

    Ju Feng; Wen Zhong Shen

    2015-01-01

    Reliable wind modelling is of crucial importance for wind farm development. The common practice of using sector-wise Weibull distributions has been found inappropriate for wind farm layout optimization. In this study, we propose a simple and easily implementable method to construct joint distributions of wind speed and wind direction, which is based on the parameters of sector-wise Weibull distributions and interpolations between direction sectors. It is applied to the wind measurement data a...

  12. Wind farm project economics : value of wind

    Energy Technology Data Exchange (ETDEWEB)

    Bills-Everett, T. [Mainstream Renewable Power, Toronto, ON (Canada)

    2010-07-01

    This PowerPoint presentation discussed methods of increasing the value of wind power projects. Appropriate turbine selection and layout is needed to ensure that wind resources are fully developed. Construction costs have a significant impact on project costs. The world turbine price index has not significantly fluctuated since 2006. Operating costs, and the value of wind power projects, are linked with OPEX fluctuations. Wind power projects can significantly reduce greenhouse gas (GHG) emissions. An increase in wind power capacity will reduce the overall cost of energy produced from wind power. Countries can use wind power as part of a renewable energy portfolio designed to reduce risks related to diminishing petroleum supplies. Wind power will help to ensure a global transition to renewable energy use. tabs., figs.

  13. Wind turbines, is it just wind?

    International Nuclear Information System (INIS)

    Boiteux, M.

    2012-01-01

    The author first outlines that wind energy is not only random, but almost absent in extreme situations when it would be needed (for example and notably, very cold weather without wind). He suggests the association of a gas turbine to each wind turbine, so that the gas turbine will replace non operating wind turbines. He notices that wind turbines are not proximity energy as they were said to be, and that profitability in fact requires tens of grouped giant wind turbines. He also outlines the high cost of construction of grids for the connection of these wind turbines. Thus, he states that wind energy is far from being profitable in the present conditions of electricity tariffs in France

  14. Healthy Places for Healthy People

    Science.gov (United States)

    Describes the Healthy Places for Healthy People technical assistance program that helps communities create walkable, healthy, economically vibrant places by engaging with local health care facility partners

  15. Wind of opportunity

    International Nuclear Information System (INIS)

    Jamieson, Peter

    1999-01-01

    This article traces the move towards the offshore exploitation of wind energy in Europe, and presents information on existing offshore wind energy projects and proposed wind turbine prototypes for offshore operation. The building of the first major offshore wind project at Vindeby, the use of rock socketed monopile foundations for pile drilling and erection of the wind turbines from a mobile jack-up barge, the costs of wind turbines, the fatigue loads on the support structures due to the wind loading, and the offshore wind market in the UK and Europe are discussed. (UK)

  16. Advanced structural wind engineering

    CERN Document Server

    Kareem, Ahsan

    2013-01-01

    This book serves as a textbook for advanced courses as it introduces state-of-the-art information and the latest research results on diverse problems in the structural wind engineering field. The topics include wind climates, design wind speed estimation, bluff body aerodynamics and applications, wind-induced building responses, wind, gust factor approach, wind loads on components and cladding, debris impacts, wind loading codes and standards, computational tools and computational fluid dynamics techniques, habitability to building vibrations, damping in buildings, and suppression of wind-induced vibrations. Graduate students and expert engineers will find the book especially interesting and relevant to their research and work.

  17. Strangers in Familiar Places

    DEFF Research Database (Denmark)

    Muhr, Sara Louise

    2012-01-01

    Employees working across multiple cultures are exposed to a vast number of different norms and values, and consequentially work is often a struggle to retain a coherent sense of self. However, when international workers travel, they also encounter more bland spaces where familiarity and similarity...... are important. These spaces appear culturally generic to the Western traveler, but are highly Westernized to bring comfort to Western employees traveling in foreign cultures. This paper argues that these spaces are important in cross-cultural identity work in the sense that international workers – professional...... strangers – need these places to belong and relate to familiarity and to regain a sense of identity. Drawing on an illustrative empirical vignette of an international consultant, I demonstrate how culturally generic spaces can be used in identity work of an international relations consultant....

  18. "Same Room, Safe Place".

    Science.gov (United States)

    Keene Woods, Nikki

    2017-04-01

    There are many different professional stances on safe sleep and then there is the reality of caring for a newborn. There is a debate among professionals regarding safe sleep recommendations. The continum of recommendations vary from the American Academy of Pediatrics (AAP) Safe Sleep Guidelines to the bed-sharing recommendations from the Mother-Baby Behavioral Sleep Laboratory. The lack of consistent and uniform safe sleep recommendations from health professionals has been confusing for families but has more recently raised a real professional ethical dilemma. Despite years of focused safe sleep community education and interventions, sleep-related infant deaths are on the rise in many communities. This commentary calls for a united safe sleep message from all health professionals to improve health for mothers and infants most at-risk, "Same Room, Safe Place."

  19. Pushing Personhood into Place

    DEFF Research Database (Denmark)

    Bidwell, Nicola J.; Winschiers-Theophilus, Heike; Kapuire, Gereon K.

    2011-01-01

    for generations; but technology-use can inadvertently displace knowledge for communities with knowledge traditions that differ from those of technology-design. Devices which are sensitive to users' locations, combined with platforms for social networking and user-generated-content, offer intriguing opportunities...... hope our reflections will inspire others to examine the spatial, temporal and social affordances of technologies within the bonds of rural communities in digitally-sparse 'under-developed' settings....... about personhood, community and place. We adopt a critical attitude towards assumptions about spatial, temporal and social logics and literacies to promote a design sensitivity to local experiences of locations. This motivates us to emphasize connections, not points, and the bodily absorption...

  20. Wind tunnel simulation of Martian sand storms

    Science.gov (United States)

    Greeley, R.

    1980-01-01

    The physics and geological relationships of particles driven by the wind under near Martian conditions were examined in the Martian Surface Wind Tunnel. Emphasis was placed on aeolian activity as a planetary process. Threshold speeds, rates of erosion, trajectories of windblown particles, and flow fields over various landforms were among the factors considered. Results of experiments on particles thresholds, rates of erosion, and the effects of electrostatics on particles in the aeolian environment are presented.

  1. Windmills for the garden. The higher and freer a wind turbine is placed in the landscape, the greater is the power generation; Windmuehlen fuer den Garten. Je hoeher und je freier ein Windrad in der Landschaft steht, desto groesser ist der Stromertrag

    Energy Technology Data Exchange (ETDEWEB)

    Krause, Dirk

    2012-09-15

    Wind turbines are no longer the domain of large operators. Even on a small scale the clean energy source can be utilized. This industrial sector is still young and very diversified. In Germany alone, interested parties may select from a range of more than 50 vendors. What should specialised craft businesses and designers pay attention to when offering the wind power plants to their customers?.

  2. Compact 3D Wind Sensor for Unmanned Aerial Vehicles, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — Accurate wide-area mapping of three-dimensional (3D) wind vectors plays an important role in our ability to understand climate processes, predict weather patterns...

  3. Wind energy - The facts. Vol. 1: Technology

    Energy Technology Data Exchange (ETDEWEB)

    Gardner, P.; Garrad, A.; Jamieson, P.; Snodin, H.; Tindal, A. (comps.) [Gerrad Hassan and partners (United Kingdom)

    2004-02-01

    The politics and economics of wind energy have played an important role in the development of the industry and contributed to its present success. Engineering is, however, pivotal. As the wind industry has become better established, the central place of engineering has become overshadowed by other issues. This is a tribute to the success of the engineers and their turbines. This volume addresses the key engineering Issues: 1) The turbines - their past achievements and future challenges - a remarkable tale of technical endeavour and entrepreneurship. 2) The wind - its characteristics and reliability - how can it be measured, quantified and harnessed? 3) The wind farms - an assembly of individual turbines into wind power stations or wind farms - their optimisation and development. 4) The grid - transporting the energy from remote locations with plentiful wind energy to the loads - the key technical and strategic challenges. This volume provides an historical overview of turbine development, describes the present status and considers future challenges. This is a remarkable story starting in the nineteenth century and then accelerating through the last two decades of the twentieth century on a course very similar to the early days of aeronautics. The story is far from finished but it has certainly started with a vengeance. Wind must be treated with great respect. The speed of the wind on a site has a very powerful effect on the economics of a wind farm; it provides both the fuel to generate electricity and the loads to destroy the turbine. This volume describes how it can be quantified, harnessed and put to work in an economic and predictable manner. The long-term behaviour of the wind is described as well as its short-term behaviour. The latter can be successfully forecast to allow wind energy to participate in electricity markets. In order for wind to live up to its raw potential promise, individual turbines must be assembled into wind farms or wind power stations

  4. Hurricane Katrina Wind Investigation Report

    Energy Technology Data Exchange (ETDEWEB)

    Desjarlais, A. O.

    2007-08-15

    This investigation of roof damage caused by Hurricane Katrina is a joint effort of the Roofing Industry Committee on Weather Issues, Inc. (RICOWI) and the Oak Ridge National Laboratory/U.S. Department of Energy (ORNL/DOE). The Wind Investigation Program (WIP) was initiated in 1996. Hurricane damage that met the criteria of a major windstorm event did not materialize until Hurricanes Charley and Ivan occurred in August 2004. Hurricane Katrina presented a third opportunity for a wind damage investigation in August 29, 2005. The major objectives of the WIP are as follows: (1) to investigate the field performance of roofing assemblies after major wind events; (2) to factually describe roofing assembly performance and modes of failure; and (3) to formally report results of the investigations and damage modes for substantial wind speeds The goal of the WIP is to perform unbiased, detailed investigations by credible personnel from the roofing industry, the insurance industry, and academia. Data from these investigations will, it is hoped, lead to overall improvement in roofing products, systems, roofing application, and durability and a reduction in losses, which may lead to lower overall costs to the public. This report documents the results of an extensive and well-planned investigative effort. The following program changes were implemented as a result of the lessons learned during the Hurricane Charley and Ivan investigations: (1) A logistics team was deployed to damage areas immediately following landfall; (2) Aerial surveillance--imperative to target wind damage areas--was conducted; (3) Investigation teams were in place within 8 days; (4) Teams collected more detailed data; and (5) Teams took improved photographs and completed more detailed photo logs. Participating associations reviewed the results and lessons learned from the previous investigations and many have taken the following actions: (1) Moved forward with recommendations for new installation procedures

  5. Vector grammars and PN machines

    Institute of Scientific and Technical Information of China (English)

    蒋昌俊

    1996-01-01

    The concept of vector grammars under the string semantic is introduced.The dass of vector grammars is given,which is similar to the dass of Chomsky grammars.The regular vector grammar is divided further.The strong and weak relation between the vector grammar and scalar grammar is discussed,so the spectrum system graph of scalar and vector grammars is made.The equivalent relation between the regular vector grammar and Petri nets (also called PN machine) is pointed.The hybrid PN machine is introduced,and its language is proved equivalent to the language of the context-free vector grammar.So the perfect relation structure between vector grammars and PN machines is formed.

  6. Wind Lidar Activities in the United States

    Energy Technology Data Exchange (ETDEWEB)

    Clifton, Andrew; Newman, Jennifer; St. Pe, Alexandra; Iungo, G. Valerio; Wharton, Sonia; Herges, Tommy; Filippelli, Matthew; Pontbriand, Philippe; Osler, Evan

    2017-06-28

    IEA Wind Task 32 seeks to identify and mitigate the barriers to the adoption of lidar for wind energy applications. This work is partly achieved by sharing experience across researchers and practitioners in the United States and worldwide. This presentation is a short summary of some wind lidar-related activities taking place in the country, and was presented by Andrew Clifton at the Task 32 meeting in December 2016 in his role as the U.S. Department of Energy-nominated country representative to the task.

  7. Wind turbine power coefficient estimation by soft computing methodologies: Comparative study

    International Nuclear Information System (INIS)

    Shamshirband, Shahaboddin; Petković, Dalibor; Saboohi, Hadi; Anuar, Nor Badrul; Inayat, Irum; Akib, Shatirah; Ćojbašić, Žarko; Nikolić, Vlastimir; Mat Kiah, Miss Laiha; Gani, Abdullah

    2014-01-01

    Highlights: • Variable speed operation of wind turbine to increase power generation. • Changeability and fluctuation of wind has to be accounted. • To build an effective prediction model of wind turbine power coefficient. • The impact of the variation in the blade pitch angle and tip speed ratio. • Support vector regression methodology application as predictive methodology. - Abstract: Wind energy has become a large contender of traditional fossil fuel energy, particularly with the successful operation of multi-megawatt sized wind turbines. However, reasonable wind speed is not adequately sustainable everywhere to build an economical wind farm. In wind energy conversion systems, one of the operational problems is the changeability and fluctuation of wind. In most cases, wind speed can vacillate rapidly. Hence, quality of produced energy becomes an important problem in wind energy conversion plants. Several control techniques have been applied to improve the quality of power generated from wind turbines. In this study, the polynomial and radial basis function (RBF) are applied as the kernel function of support vector regression (SVR) to estimate optimal power coefficient value of the wind turbines. Instead of minimizing the observed training error, SVR p oly and SVR r bf attempt to minimize the generalization error bound so as to achieve generalized performance. The experimental results show that an improvement in predictive accuracy and capability of generalization can be achieved by the SVR approach in compare to other soft computing methodologies

  8. Grid-connected inverter for wind power generation system

    Institute of Scientific and Technical Information of China (English)

    YANG Yong; RUAN Yi; SHEN Huan-qing; TANG Yan-yan; YANG Ying

    2009-01-01

    In wind power generation system the grid-connected inverter is an important section for energy conversion and transmission, of which the performance has a direct influence on the entire wind power generation system. The mathematical model of the grid-connected inverter is deduced firstly. Then, the space vector pulse width modulation (SVPWM) is analyzed. The power factor can be controlled close to unity, leading or lagging, which is realized based on PI-type current controller and grid voltage vector-oriented control. The control strategy is verified by the simulation and experimental results with a good sinusoidal current, a small harmonic component and a fast dynamic response.

  9. Update-in-Place Analysis for True Multidimensional Arrays

    Directory of Open Access Journals (Sweden)

    Steven M. Fitzgerald

    1996-01-01

    Full Text Available Applicative languages have been proposed for defining algorithms for parallel architectures because they are implicitly parallel and lack side effects. However, straightforward implementations of applicative-language compilers may induce large amounts of copying to preserve program semantics. The unnecessary copying of data can increase both the execution time and the memory requirements of an application. To eliminate the unnecessary copying of data, the Sisal compiler uses both build-in-place and update-in-place analyses. These optimizations remove unnecessary array copy operations through compile-time analysis. Both build-in-place and update-in-place are based on hierarchical ragged arrays, i.e., the vector-of-vectors array model. Although this array model is convenient for certain applications, many optimizations are precluded, e.g., vectorization. To compensate for this deficiency, new languages, such as Sisal 2.0, have extended array models that allow for both high-level array operations to be performed and efficient implementations to be devised. In this article, we introduce a new method to perform update-in-place analysis that is applicable to arrays stored either in hierarchical or in contiguous storage. Consequently, the array model that is appropriate for an application can be selected without the loss of performance. Moreover, our analysis is more amenable for distributed memory and large software systems.

  10. Wind load effects on high rise buildings in Peninsular Malaysia

    Science.gov (United States)

    Nizamani, Z.; Thang, K. C.; Haider, B.; Shariff, M.

    2018-04-01

    Wind is a randomly varying dynamic phenomenon composed of a multitude of eddies of varying sizes and rotational characteristics along a general stream of air moving relative to the ground. These eddies give wind its gustiness, creating fluctuation and results in a complex flow characteristics. The wind vector at any point can be regarded as the sum of mean wind vector and the fluctuation components. These components not only vary with height but also dependant on the approach terrain and topography. Prevailing wind exerts pressure onto the structural surfaces. The effects of wind pressure in the form of shear and bending moments are found to be a major problem in structural failure. This study aims to study the effects of wind load on a fifteen-storey high rise building using EN 1991-1-4 code and MS1553:2002. The simulation results showed that by increasing the wind speed, the storey resultant forces, namely storey shear and storey moment increases significantly. Furthermore, simulation results according to EN 1991-1-4 yield higher values compared to the simulation results according to MS1553:2002.

  11. Vehicle Based Vector Sensor

    Science.gov (United States)

    2015-09-28

    buoyant underwater vehicle with an interior space in which a length of said underwater vehicle is equal to one tenth of the acoustic wavelength...underwater vehicle with an interior space in which a length of said underwater vehicle is equal to one tenth of the acoustic wavelength; an...unmanned underwater vehicle that can function as an acoustic vector sensor. (2) Description of the Prior Art [0004] It is known that a propagating

  12. Reciprocity in Vector Acoustics

    Science.gov (United States)

    2017-03-01

    Green’s Theorem to the left hand side of Equation (3.2) converts it to a surface integral that vanishes for the impedance boundary conditions one...There are situations where this assumption does not hold, such as at boundaries between layers or in an inhomogeneous layer , because the density gradient...instead of requiring one model run for each source location. Application of the vector-scalar reciprocity principle is demonstrated with analytic

  13. Tensor Calculus: Unlearning Vector Calculus

    Science.gov (United States)

    Lee, Wha-Suck; Engelbrecht, Johann; Moller, Rita

    2018-01-01

    Tensor calculus is critical in the study of the vector calculus of the surface of a body. Indeed, tensor calculus is a natural step-up for vector calculus. This paper presents some pitfalls of a traditional course in vector calculus in transitioning to tensor calculus. We show how a deeper emphasis on traditional topics such as the Jacobian can…

  14. Technical Training - Places available

    CERN Multimedia

    Monique Duval

    2003-01-01

    Places are available in the following courses: HeREF-2003 : Techniques de la réfrigération Hélium :  6 - 10.10.2003  (7 demi-journées, cours en français avec support en anglais)  The Java Programming Language Level 1:  6 - 7.10.2003  (2 days) Java 2 Enterprise Edition - Part 2: Enterprise JavaBeans: 8 - 10.10.2003  (3 days) FileMaker - niveau 1 : 9 & 10.10.03 (2 jours) EXCEL 2000 - niveau 1 :  20 & 22.10.03  (2 jours) AutoCAD 2002 - niveau 1 :  20, 21, 27, 28.10.03  (4 jours) CLEAN-2002 : Working in a Cleanroom: 23.10.03  (half day, free of charge) Plannification de projet avec MS-Project/ Project Scheduling with MS-Project : 2 sessions:  23.10 & 4.11.03  (2 jours/2 days and 18 &25.11.03 langue à définir/language to be defined) AutoCAD 2002 - Level 1:  3, 4, 12, 13.11.03  (4 days) Introduction to Pspice:  4.11.03p.m.  (half-day) AutoCAD 2002 - niveau 2 :  10 & 11.11.03  (2 jours) ACCESS 2000 - niveau 1 :  13 & 14.11.03  (2 jours) A...

  15. Direct vector controlled six-phase asymmetrical induction motor with power balanced space vector PWM multilevel operation

    DEFF Research Database (Denmark)

    Padmanaban, Sanjeevi Kumar; Grandi, Gabriele; Ojo, Joseph Olorunfemi

    2016-01-01

    In this paper, a six-phase (asymmetrical) machine is investigated, 300 phase displacement is set between two three-phase stator windings keeping deliberately in open-end configuration. Power supply consists of four classical three-phase voltage inverters (VSIs), each one connected to the open......-winding terminals. An original synchronous field oriented control (FOC) algorithm with three variables as degree of freedom is proposed, allowing power sharing among the four VSIs in symmetric/asymmetric conditions. A standard three-level space vector pulse width modulation (SVPWM) by nearest three vector (NTV......) approach was adopted for each couple of VSIs to operate as multilevel output voltage generators. The proposed power sharing algorithm is verified for the ac drive system by observing the dynamic behaviours in different set conditions by complete simulation modelling in software (Matlab...

  16. Limited change in dune mobility in response to a large decrease in wind power in semi-arid northern China since the 1970s

    Science.gov (United States)

    Mason, J.A.; Swinehart, J.B.; Lu, H.; Miao, X.; Cha, P.; Zhou, Y.

    2008-01-01

    The climatic controls on dune mobility, especially the relative importance of wind strength, remain incompletely understood. This is a key research problem in semi-arid northern China, both for interpreting past dune activity as evidence of paleoclimate and for predicting future environmental change. Potential eolian sand transport, which is approximately proportional to wind power above the threshold for sand entrainment, has decreased across much of northern China since the 1970s. Over the same period, effective moisture (ratio of precipitation to potential evapotranspiration) has not changed significantly. This "natural experiment" provides insight on the relative importance of wind power as a control on dune mobility in three dunefields of northern China (Mu Us, Otindag, and Horqin), although poorly understood and potentially large effects of human land use complicate interpretation. Dune forms in these three regions are consistent with sand transport vectors inferred from weather station data, suggesting that wind directions have remained stable and the stations adequately represent winds that shaped the dunes. The predicted effect of weaker winds since the 1970s would be dune stabilization, with lower sand transport rates allowing vegetation cover to expand. Large portions of all three dunefields remained stabilized by vegetation in the 1970s despite high wind power. Since the 1970s, trends in remotely sensed vegetation greenness and change in mobile dune area inferred from sequential Landsat images do indicate widespread dune stabilization in the eastern Mu Us region. On the other hand, expansion of active dunes took place farther west in the Mu Us dunefield and especially in the central Otindag dunefield, with little overall change in two parts of the Horqin dunes. Better ground truth is needed to validate the remote sensing analyses, but results presented here place limits on the relative importance of wind strength as a control on dune mobility in the

  17. Doppler Lidar Vector Retrievals and Atmospheric Data Visualization in Mixed/Augmented Reality

    Science.gov (United States)

    Cherukuru, Nihanth Wagmi

    Environmental remote sensing has seen rapid growth in the recent years and Doppler wind lidars have gained popularity primarily due to their non-intrusive, high spatial and temporal measurement capabilities. While lidar applications early on, relied on the radial velocity measurements alone, most of the practical applications in wind farm control and short term wind prediction require knowledge of the vector wind field. Over the past couple of years, multiple works on lidars have explored three primary methods of retrieving wind vectors viz., using homogeneous windfield assumption, computationally extensive variational methods and the use of multiple Doppler lidars. Building on prior research, the current three-part study, first demonstrates the capabilities of single and dual Doppler lidar retrievals in capturing downslope windstorm-type flows occurring at Arizona's Barringer Meteor Crater as a part of the METCRAX II field experiment. Next, to address the need for a reliable and computationally efficient vector retrieval for adaptive wind farm control applications, a novel 2D vector retrieval based on a variational formulation was developed and applied on lidar scans from an offshore wind farm and validated with data from a cup and vane anemometer installed on a nearby research platform. Finally, a novel data visualization technique using Mixed Reality (MR)/ Augmented Reality (AR) technology is presented to visualize data from atmospheric sensors. MR is an environment in which the user's visual perception of the real world is enhanced with live, interactive, computer generated sensory input (in this case, data from atmospheric sensors like Doppler lidars). A methodology using modern game development platforms is presented and demonstrated with lidar retrieved wind fields. In the current study, the possibility of using this technology to visualize data from atmospheric sensors in mixed reality is explored and demonstrated with lidar retrieved wind fields as well as

  18. Wind engineering in Africa

    NARCIS (Netherlands)

    Wisse, J.A.; Stigter, C.J.

    2007-01-01

    The International Association for Wind Engineering (IAWE) has very few contacts in Africa, the second-largest continent. This paper reviews important wind-related African issues. They all require data on wind climate, which are very sparse in Africa. Wind engineering in Africa can assist in

  19. The significance of vector magnetic field measurements

    Science.gov (United States)

    Hagyard, M. J.

    1990-01-01

    Observations of four flaring solar active regions, obtained during 1980-1986 with the NASA Marshall vector magnetograph (Hagyard et al., 1982 and 1985), are presented graphically and characterized in detail, with reference to nearly simultaneous Big Bear Solar Observatory and USAF ASW H-alpha images. It is shown that the flares occurred where local photospheric magnetic fields differed most from the potential field, with initial brightening on either side of a magnetic-neutral line near the point of maximum angular shear (rather than that of maximum magnetic-field strength, typically 1 kG or greater). Particular emphasis is placed on the fact that these significant nonpotential features were detected only by measuring all three components of the vector magnetic field.

  20. A woman's rightful place?

    Science.gov (United States)

    1993-04-01

    Rural development projects in sub-Saharan Africa tend not to succeed because they do not consider women's role and their significance, even though women constitute 70% of agricultural workers, 80% of food producers, 100% of people who prepare meals, and 60-90% do food marketing. Development specialists ignore women because they are not involved in political activities and in decision making. As long as women and women's contributions are not considered, rural development projects will remain inefficient and development will not take place. Thus, projects must include women as agents and beneficiaries of development in key sectors of the economy. Rural development specialists must also consider the effect male labor emigration has on rural women. For example, drought has forced many men to leave their villages, leaving a work force consisting of 95% women to fight desertification. All too often, women have no or limited land ownership rights, thereby keeping them from improving the land, e.g., planting perennial fruit crops. They also tend to be hired hands rather than food producers. They cannot obtain bank loans because they do not own land, and because they are often illiterate (over 90% female illiteracy in 28 African countries), they can neither understand nor complete bank loan forms. Rural development projects further alienate women by aiming training programs to men or by using male agricultural extension agents. Women react to this alienation by rejecting projects that do not benefit them and follow more profitable activities which sometimes interfere with projects. Thus, rural development programs need to invest in women to ensure viable and efficient sustainable development.