Satellite drag effects due to uplifted oxygen neutrals during super magnetic storms

Science.gov (United States)

Lakhina, Gurbax S.; Tsurutani, Bruce T.

2017-12-01

During intense magnetic storms, prompt penetration electric fields (PPEFs) through E × B forces near the magnetic equator uplift the dayside ionosphere. This effect has been called the dayside super-fountain effect. Ion-neutral drag forces between the upward moving O+ (oxygen ions) and oxygen neutrals will elevate the oxygen atoms to higher altitudes. This paper gives a linear calculation indicating how serious the effect may be during an 1859-type (Carrington) superstorm. It is concluded that the oxygen neutral densities produced at low-Earth-orbiting (LEO) satellite altitudes may be sufficiently high to present severe satellite drag. It is estimated that with a prompt penetrating electric field of ˜ 20 mV m-1 turned on for 20 min, the O atoms and O+ ions are uplifted to 850 km where they produce about 40-times-greater satellite drag per unit mass than normal. Stronger electric fields will presumably lead to greater uplifted mass.

The Effect of Wind Forcing on Modeling Coastal Circulation at a Marine Renewable Test Site

Directory of Open Access Journals (Sweden)

Lei Ren

2017-12-01

Full Text Available The hydrodynamic circulation in estuaries is primarily driven by tides, river inflows and surface winds. While tidal and river data can be quite easily obtained for input to hydrodynamic models, sourcing accurate surface wind data is problematic. Inaccurate wind data can lead to inaccuracies in the surface currents computed by three-dimensional hydrodynamic models. In this research, a high-resolution wind model was coupled with a three-dimensional hydrodynamic model of Galway Bay, a semi-enclosed estuary on the west coast of Ireland, to investigate the effect of wind forcing on model accuracy. Two wind-forcing conditions were investigated: (1 using wind data measured onshore on the NUI Galway campus (NUIG and (2 using offshore wind data provided by a high resolution wind model (HR. A scenario with no wind forcing (NW was also assessed. The onshore wind data varied with time but the speed and direction were applied across the full model domain. The modeled offshore wind fields varied with both time and space. The effect of wind forcing on modeled hydrodynamics was assessed via comparison of modeled surface currents with surface current measurements obtained from a High-Frequency (HF radar Coastal Ocean Dynamics Applications Radar (CODAR observation system. Results indicated that winds were most significant in simulating the north-south surface velocity component. The model using high resolution temporally- and spatially-varying wind data achieved better agreement with the CODAR surface currents than the model using the onshore wind measurements and the model without any wind forcing.

Uplifting Leadership

Science.gov (United States)

Hargreaves, Andy; Boyle, Alan

2015-01-01

To find out how organizations turn failure into success, Andrew Hargreaves and his colleagues studied more than 15 business, sports, and education organizations. They found that the secret to these organizations' success came down to just two words: uplifting leadership. Uplifting leadership, write Hargreaves and Boyle in this article, raises the…

An Evaluation of Wind Turbine Technology at Peterson Air Force Base

Science.gov (United States)

2005-03-01

by the wind speed. Darrieus turbines are ordinarily inexpensive and are used for electricity generation and irrigation. One advantage to a...AN EVALUATION OF WIND TURBINE TECHNOLOGY...02 AN EVALUATION OF WIND TURBINE TECHNOLOGY AT PETERSON AIR FORCE BASE THESIS Presented to the Faculty Department of

Colorado Plateau magmatism and uplift by warming of heterogeneous lithosphere.

Science.gov (United States)

Roy, Mousumi; Jordan, Thomas H; Pederson, Joel

2009-06-18

The forces that drove rock uplift of the low-relief, high-elevation, tectonically stable Colorado Plateau are the subject of long-standing debate. While the adjacent Basin and Range province and Rio Grande rift province underwent Cenozoic shortening followed by extension, the plateau experienced approximately 2 km of rock uplift without significant internal deformation. Here we propose that warming of the thicker, more iron-depleted Colorado Plateau lithosphere over 35-40 Myr following mid-Cenozoic removal of the Farallon plate from beneath North America is the primary mechanism driving rock uplift. In our model, conductive re-equilibration not only explains the rock uplift of the plateau, but also provides a robust geodynamic interpretation of observed contrasts between the Colorado Plateau margins and the plateau interior. In particular, the model matches the encroachment of Cenozoic magmatism from the margins towards the plateau interior at rates of 3-6 km Myr(-1) and is consistent with lower seismic velocities and more negative Bouguer gravity at the margins than in the plateau interior. We suggest that warming of heterogeneous lithosphere is a powerful mechanism for driving epeirogenic rock uplift of the Colorado Plateau and may be of general importance in plate-interior settings.

Development of a Wind Directly Forced Heat Pump and Its Efficiency Analysis

Directory of Open Access Journals (Sweden)

Ching-Song Jwo

2013-01-01

Full Text Available The requirements of providing electric energy through the wind-forced generator to the heat pump for water cooling and hot water heating grow significantly by now. This study proposes a new technique to directly adopt the wind force to drive heat pump systems, which can effectively reduce the energy conversion losses during the processes of wind force energy converting to electric energy and electric energy converting to kinetic energy. The operation of heat pump system transfers between chiller and heat that are controlled by a four-way valve. The theoretical efficiency of the traditional method, whose heat pump is directly forced by wind, is 42.19%. The experimental results indicated average value for cool water producing efficiency of 54.38% in the outdoor temperature of 35°C and the indoor temperature of 25°C and the hot water producing efficiency of 52.25% in the outdoor temperature and the indoor temperature both of 10°C. We proposed a method which can improve the efficiency over 10% in both cooling and heating.

Vandenberg Air Force Base Pressure Gradient Wind Study

Science.gov (United States)

Shafer, Jaclyn A.

2013-01-01

Warning category winds can adversely impact day-to-day space lift operations at Vandenberg Air Force Base (VAFB) in California. NASA's Launch Services Program and other programs at VAFB use wind forecasts issued by the 30 Operational Support Squadron Weather Flight (30 OSSWF) to determine if they need to limit activities or protect property such as a launch vehicle. The 30 OSSWF tasked the AMU to develop an automated Excel graphical user interface that includes pressure gradient thresholds between specific observing stations under different synoptic regimes to aid forecasters when issuing wind warnings. This required the AMU to determine if relationships between the variables existed.

Fundamental study on aerodynamic force of floating offshore wind turbine with cyclic pitch mechanism

International Nuclear Information System (INIS)

Li, Qing'an; Kamada, Yasunari; Maeda, Takao; Murata, Junsuke; Iida, Kohei; Okumura, Yuta

2016-01-01

Wind turbines mounted on floating platforms are subjected to completely different and soft foundation properties, rather than onshore wind turbines. Due to the flexibility of their mooring systems, floating offshore wind turbines are susceptible to large oscillations such as aerodynamic force of the wind and hydrodynamic force of the wave, which may compromise their performance and structural stability. This paper focuses on the evaluation of aerodynamic forces depending on suppressing undesired turbine's motion by a rotor thrust control which is controlled by pitch changes with wind tunnel experiments. In this research, the aerodynamic forces of wind turbine are tested at two kinds of pitch control system: steady pitch control and cyclic pitch control. The rotational speed of rotor is controlled by a variable speed generator, which can be measured by the power coefficient. Moment and force acts on model wind turbine are examined by a six-component balance. From cyclic pitch testing, the direction and magnitude of moment can be arbitrarily controlled by cyclic pitch control. Moreover, the fluctuations of thrust coefficient can be controlled by collective pitch control. The results of this analysis will help resolve the fundamental design of suppressing undesired turbine's motion by cyclic pitch control. - Highlights: • Offshore wind offers additional options in regions with low onshore potential. • Two kinds of pitch control system: Steady pitch control and Cyclic pitch control. • Performance curves and unsteady aerodynamics are investigated in wind tunnel. • Fluctuations of thrust coefficient can be controlled by collective pitch control.

Satellite drag effects due to uplifted oxygen neutrals during super magnetic storms

Directory of Open Access Journals (Sweden)

G. S. Lakhina

2017-12-01

Full Text Available During intense magnetic storms, prompt penetration electric fields (PPEFs through E  ×  B forces near the magnetic equator uplift the dayside ionosphere. This effect has been called the dayside super-fountain effect. Ion-neutral drag forces between the upward moving O+ (oxygen ions and oxygen neutrals will elevate the oxygen atoms to higher altitudes. This paper gives a linear calculation indicating how serious the effect may be during an 1859-type (Carrington superstorm. It is concluded that the oxygen neutral densities produced at low-Earth-orbiting (LEO satellite altitudes may be sufficiently high to present severe satellite drag. It is estimated that with a prompt penetrating electric field of ∼ 20 mV m−1 turned on for 20 min, the O atoms and O+ ions are uplifted to 850 km where they produce about 40-times-greater satellite drag per unit mass than normal. Stronger electric fields will presumably lead to greater uplifted mass.

Analysis of Disturbance Source Inducing by The Variable Speed Wind Turbine System Forced Power Oscillations

DEFF Research Database (Denmark)

Tan, Jin; Hu, Weihao; Wang, Xiaoru

2015-01-01

The main focus of forced low frequency oscillations is to analyze the disturbance source and the origin of forced oscillations. In this paper, the origin of low-frequency periodical oscillations induced by wind turbines’ mechanical power is investigated and the mechanism is studied of fluctuating...... power transfer through permanent magnet generator wind turbine system. Considering the tower shadow and the wind shear effect, the mechanical and generator coupling model is developed by PSCAD. Simulation is done to analyze the impacts on output power of operation points and mechanical fluctuation...... components. It is shown that when the oscillation frequency of tower shadow coincides with the system natural frequency, it may cause forced oscillations, whereas, the wind shear and natural wind speed fluctuation are not likely to induce forced oscillations....

Observation and Numerical Experiments for Drag Coefficient Under Typhoon Wind Forcing

Institute of Scientific and Technical Information of China (English)

CAO Huiqiu; ZHOU Liangming; LI Shuiqing; WANG Zhifeng

2017-01-01

This paper presents a study on drag coefficients under typhoon wind forcing based on observations and numerical experiments.The friction velocity and wind speed are measured at a marine observation platform in the South China Sea.Three typhoons:SOULIK (2013),TRAMI (2013) and FITOW (2013) are observed at a buoy station in the northeast sea area of Pingtan Island.A new parameterization is formulated for the wind drag coefficient as a function of wind speed.It is found that the drag coefficient (Ca) increases linearly with the slope of 0.083× 10-3 for wind speed less than 24 m s-1.To investigate the drag coefficient under higher wind conditions,three numerical experiments are implemented for these three typhoons using SWAN wave model.The wind input data are objective reanalysis datasets,which are assimilated with many sources and provided every six hours with the resolution of 0.125° ×0.125°.The numerical simulation results show a good agreement with wave observation data under typhoon wind forcing.The results indicate that the drag coefficient levels off with the linear slope of 0.012× 10-3 for higher wind speeds (less than 34 m s-1) and the new parameterization improvese the simulation accuracy compared with the Wu (1982) default used in SWAN.

Examination of forced unsteady separated flow fields on a rotating wind turbine blade

Energy Technology Data Exchange (ETDEWEB)

Huyer, S [Univ. of Colorado, Boulder, CO (US)

1993-04-01

The wind turbine industry faces many problems regarding the construction of efficient and predictable wind turbine machines. Steady state, two-dimensional wind tunnel data are generally used to predict aerodynamic loads on wind turbine blades. Preliminary experimental evidence indicates that some of the underlying fluid dynamic phenomena could be attributed to dynamic stall, or more specifically to generation of forced unsteady separated flow fields. A collaborative research effort between the University of Colorado and the National Renewable Energy Laboratory was conducted to systematically categorize the local and global effects of three- dimensional forced unsteady flow fields.

An estimation method for basemat uplift behavior of NPP buildings

International Nuclear Information System (INIS)

Nakamura, N.; Ino, S.; Kurimoto, O.; Miake, M.

2005-01-01

It is important to accurately estimate the effects of strong earthquake motions on the basemat uplift behavior and structural responses for the seismic design of nuclear power plant buildings. In this paper, an analysis model which describes the soil part using the 3 dimensional FEM was proposed to be used when the ground contact ratio is low, and the validity of this model was confirmed. Furthermore, investigations using the model were carried out where the attaching force under the basemat was taken into account, in order to more realistically estimate the basemat uplift behavior. The effects in the case of the building being embedded were also investigated. (authors)

Analysis and control of the compaction force in the composite prepreg tape winding process for rocket motor nozzles

Directory of Open Access Journals (Sweden)

Xiaodong He

2017-04-01

Full Text Available In the process of composite prepreg tape winding, the compaction force could influence the quality of winding products. According to the analysis and experiments, during the winding process of a rocket motor nozzle aft exit cone with a winding angle, there would be an error between the deposition speed of tape layers and the feeding speed of the compaction roller, which could influence the compaction force. Both a lack of compaction and overcompaction related to the feeding of the compaction roller could result in defects of winding nozzles. Thus, a flexible winding system has been developed for rocket motor nozzle winding. In the system, feeding of the compaction roller could be adjusted in real time to achieve an invariable compaction force. According to experiments, the force deformation model of the winding tape is a time-varying system. Thus, a forgetting factor recursive least square based parameter estimation proportional-integral-differential (PID controller has been developed, which could estimate the time-varying parameter and control the compaction force by adjusting the feeding of the compaction roller during the winding process. According to the experimental results, a winding nozzle with fewer voids and a smooth surface could be wounded by the invariable compaction force in the flexible winding system.

Response of Ocean Circulation to Different Wind Forcing in Puerto Rico and US Virgin Islands

Science.gov (United States)

Solano, Miguel; Garcia, Edgardo; Leonardi, Stafano; Canals, Miguel; Capella, Jorge

2013-11-01

The response of the ocean circulation to various wind forcing products has been studied using the Regional Ocean Modeling System. The computational domain includes the main islands of Puerto Rico, Saint John and Saint Thomas, located on the continental shelf dividing the Caribbean Sea and the Atlantic Ocean. Data for wind forcing is provided by an anemometer located in a moored buoy, the Coupled Ocean-Atmosphere Mesoscale Prediction System (COAMPS) model and the National Digital Forecast Database (NDFD). Hindcast simulations have been validated using hydrographic data at different locations in the area of study. Three cases are compared to quantify the impact of high resolution wind forcing on the ocean circulation and the vertical structure of salinity, temperature and velocity. In the first case a constant wind velocity field is used to force the model as measured by an anemometer on top of a buoy. In the second case, a forcing field provided by the Navy's COAMPS model is used and in the third case, winds are taken from NDFD in collaboration with the National Centers for Environmental Prediction. Validated results of ocean currents against data from Acoustic Doppler Current Profilers at different locations show better agreement using high resolution wind data as expected. Thanks to CariCOOS and NOAA.

Uplifting the Iwasawa

International Nuclear Information System (INIS)

Franzen, A.; Kaura, P.; Ray, R.; Misra, A.

2006-01-01

The Iwasawa manifold is uplifted to seven-folds of either G 2 holonomy or SU(3) structure, explicit new metrics for the same having been constructed in this work. We uplift the Iwasawa manifold to a G 2 manifold through ''size'' deformation (of the Iwasawa metric), via Hitchin's Flow equations, showing also the impossibility of the uplift for ''shape'' and ''size'' deformations (of the Iwasawa metric). Using results of Dall'Agata and Prezas, Phys. Rev. D 69, 066004 (2004) [arXiv:hep-th/0311146] [1], we also uplift the Iwasawa manifold to a 7-fold with SU(3) structure through ''size'' and ''shape'' deformations via generalisation of Hitchin's Flow equations. For seven-folds with SU(3)-structure, the result could be interpreted as M5-branes wrapping two-cycles embedded in the seven-fold (as in [1]) - a warped product of either a special hermitian six-fold or a balanced six-fold with the unit interval. There can be no uplift to seven-folds of SU(3) structure involving non-trivial ''size'' and ''shape'' deformations (of the Iwasawa metric) retaining the ''standard complex structure'' - the uplift generically makes one move in the space of almost complex structures such that one is neither at the standard complex structure point nor at the ''edge''. Using the results of Konopelchenko and Landolfi, J. Geom. Phys. 29, 319 (1999) [arXiv:math.DG/9804144] [2], we show that given two ''shape deformation'' functions, and the dilaton, one can construct a Riemann surface obtained via Weierstrass representation for the conformal immersion of a surface in R l , for a suitable l, with the condition of having conformal immersion being a quadric in CP l-1 . (Abstract Copyright [2006], Wiley Periodicals, Inc.)

The dynamics of İzmir Bay under the effects of wind and thermohaline forces

Science.gov (United States)

Sayın, Erdem; Eronat, Canan

2018-04-01

The dominant circulation pattern of İzmir Bay on the Aegean Sea coast of Turkey is studied taking into consideration the influence of wind and thermohaline forces. İzmir Bay is discussed by subdividing the bay into outer, middle and inner areas. Wind is the most important driving force in the İzmir coastal area. There are also thermohaline forces due to the existence of water types of different physical properties in the bay. In contrast to the two-layer stratification during summer, a homogeneous water column exists in winter. The free surface version of the Princeton model (Killworth's 3-D general circulation model) is applied, with the input data obtained through the measurements made by the research vessel K. Piri Reis. As a result of the simulations with artificial wind, the strong consistent wind generates circulation patterns independent of the seasonal stratification in the bay. Wind-driven circulation causes cyclonic or anticyclonic movements in the middle bay where the distinct İzmir Bay Water (IBW) forms. Cyclonic movement takes place under the influence of southerly and westerly winds. On the other hand, northerly and easterly winds cause an anticyclonic movement in the middle bay. The outer and inner bay also have the wind-driven recirculation patterns expected.

Harmonic Fluxes and Electromagnetic Forces of Concentric Winding Brushless Permanent Magnet Motor

Science.gov (United States)

Ishibashi, Fuminori; Takemasa, Ryo; Matsushita, Makoto; Nishizawa, Takashi; Noda, Shinichi

Brushless permanent magnet motors have been widely used in home applications and industrial fields. These days, high efficiency and low noise motors are demanded from the view point of environment. Electromagnetic noise and iron loss of the motor are produced by the harmonic fluxes and electromagnetic forces. However, order and space pattern of these have not been discussed in detail. In this paper, fluxes, electromagnetic forces and magneto-motive forces of brushless permanent magnet motors with concentric winding were analyzed analytically, experimentally and numerically. Time harmonic fluxes and time electromagnetic forces in the air gap were measured by search coils on the inner surface of the stator teeth and analyzed by FEM. Space pattern of time harmonic fluxes and time electromagnetic forces were worked out with experiments and FEM. Magneto motive forces due to concentric winding were analyzed with equations and checked by FEM.

Breaking wave impact forces on truss support structures for offshore wind turbines

Science.gov (United States)

Cieślikiewicz, Witold; Gudmestad, Ove T.; Podrażka, Olga

2014-05-01

Due to depletion of the conventional energy sources, wind energy is becoming more popular these days. Wind energy is being produced mostly from onshore farms, but there is a clear tendency to transfer wind farms to the sea. The foundations of offshore wind turbines may be truss structures and might be located in shallow water, where are subjected to highly varying hydrodynamic loads, particularly from plunging breaking waves. There are models for impact forces prediction on monopiles. Typically the total wave force on slender pile from breaking waves is a superposition of slowly varying quasi-static force, calculated from the Morison equation and additional dynamical, short duration force due to the impact of the breaker front or breaker tongue. There is not much research done on the truss structures of wind turbines and there are still uncertainties on slamming wave forces, due to plunging breaking waves on those structures. Within the WaveSlam (Wave slamming forces on truss structures in shallow water) project the large scale tests were carried out in 2013 at the Large Wave Flume in Forschungszentrum Küste (FZK) in Hannover, Germany. The following institutions participated in this initiative: the University of Stavanger and the Norwegian University of Science and Technology (project management), University of Gdańsk, Poland, Hamburg University of Technology and the University of Rostock, Germany and Reinertsen AS, Norway. This work was supported by the EU 7th Framework Programme through the grant to the budget of the Integrating Activity HYDRALAB IV. The main aim of the experiment was to investigate the wave slamming forces on truss structures, development of new and improvement of existing methods to calculate forces from the plunging breakers. The majority of the measurements were carried out for regular waves with specified frequencies and wave heights as well as for the irregular waves based on JONSWAP spectrum. The truss structure was equipped with both

Wind-forced modulations in crossing sea states over infinite depth water

Science.gov (United States)

Debsarma, Suma; Senapati, Sudipta; Das, K. P.

2014-09-01

The present work is motivated by the work of Leblanc ["Amplification of nonlinear surface waves by wind," Phys. Fluids 19, 101705 (2007)] which showed that Stokes waves grow super exponentially under fair wind as a result of modulational instability. Here, we have studied the effect of wind in a situation of crossing sea states characterized by two obliquely propagating wave systems in deep water. It is found that the wind-forced uniform wave solution in crossing seas grows explosively with a super-exponential growth rate even under a steady horizontal wind flow. This is an important piece of information in the context of the formation of freak waves.

Electromagnetic force analysis on the stator and rotor windings of a superconducting generator

International Nuclear Information System (INIS)

Colovini, L.; Martinelli, G.; Morini, A.

1985-01-01

The determination of values and distribution of the forces acting on the components of a superconducting generator is important when designing the machine, particularly in the choice of materials. The paper analyses the electromagnetic forces acting on the field and armature windings; for this purpose, with reference to the preliminary design of a two-pole 300 MVA superconducting generator, a two-dimensional analytical method set up by the authors is utilized to calculate the forces on the windings under steady state operation and results are compared with those obtained by means of a numerical method

24 CFR 3285.5 - Definitions.

Science.gov (United States)

2010-04-01

... circuits, water pipes, drain plumbing, and gas lines. Design Approval Primary Inspection Agency (DAPIA). A... forces, but which may resist vertical, uplift, and overturning forces. Flood hazard area. The greater of..., gas, or fuel oil. Vertical tie. A tie intended to resist uplifting and overturning forces. Wind zone...

Why the Coriolis force turns a wind farm wake clockwise in the Northern Hemisphere

DEFF Research Database (Denmark)

van der Laan, Paul; Sørensen, Niels N.

2017-01-01

simulations. A momentum balance in the cross flow direction shows that the interaction between the Coriolis force and the 5 × 5 actuator disks is complex due to turbulent mixing of veered momentum from above into the wind farm, which is not observed for the interaction between the Coriolis force...... wake and not the local changes in the Coriolis force in the wake deficit region. An additional simulation of a single actuator disk, operating in a shallow atmospheric boundary layer, confirms that the Coriolis force indirectly turns a wind turbine wake clockwise, as observed from above, due...

Erodibility of waste (Loess) soils from construction sites under water and wind erosional forces.

Science.gov (United States)

Tanner, Smadar; Katra, Itzhak; Argaman, Eli; Ben-Hur, Meni

2018-03-01

Excess soils from construction sites (waste soils) become a problem when exposed to soil erosion by water or wind. Understanding waste soil erodibility can contribute to its proper reuse for various surface applications. The general objective of the study was to provide a better understanding of the effects of soil properties on erodibility of waste soils excavated from various depths in a semiarid region under rainfall and wind erosive forces. Soil samples excavated from the topsoil (0-0.3m) and subsoil layers (0.3-0.9 and >1m depths) were subjected to simulated rainfall and wind. Under rainfall erosive forces, the subsoils were more erodible than the topsoil, in contrast to the results obtained under wind erosive forces. Exchangeable sodium percentage was the main factor controlling soil erodibility (K i ) under rainfall, and a significant logarithmic regression line was found between these two parameters. In addition, a significant, linear regression was found between K i and slaking values for the studied soil samples, suggesting that the former can be predicted from the latter. Soil erodibility under wind erosion force was controlled mainly by the dry aggregate characteristics (mean weight diameter and aggregate density): their higher values in the subsoil layers resulted in lower soil erodibility compared to the topsoil. Copyright © 2017 Elsevier B.V. All rights reserved.

Forces and Moments on Flat Plates of Small Aspect Ratio with Application to PV Wind Loads and Small Wind Turbine Blades

Directory of Open Access Journals (Sweden)

Xavier Ortiz

2015-03-01

Full Text Available To improve knowledge of the wind loads on photovoltaic structures mounted on flat roofs at the high angles required in high latitudes, and to study starting flow on low aspect ratio wind turbine blades, a series of wind tunnel tests were undertaken. Thin flat plates of aspect ratios between 0.4 and 9.0 were mounted on a sensitive three-component instantaneous force and moment sensor. The Reynolds numbers varied from 6 × 104 to 2 × 105. Measurements were made for angles of attack between 0° and 90° both in the free stream and in wall proximity with increased turbulence and mean shear. The ratio of drag to lift closely follows the inverse tangent of the angle of incidence for virtually all measurements. This implies that the forces of interest are due largely to the instantaneous pressure distribution around the plate and are not significantly influenced by shear stresses. The instantaneous forces appear most complex for the smaller aspect ratios but the intensity of the normal force fluctuations is between 10% and 20% in the free-steam but can exceed 30% near the wall. As the wind tunnel floor is approached, the lift and drag reduce with increasing aspect ratio, and there is a reduction in the high frequency components of the forces. It is shown that the centre of pressure is closer to the centre of the plates than the quarter-chord position for nearly all cases.

Wind and Current Forces Acting on Canadian Forces Ships During Tug Operations

Science.gov (United States)

2002-11-01

McTaggart and Sav- age [1] describe model tests conducted on a generic frigate model to determine wind forces influencing ship capsize. Van Manen and van ...Fn will be 0.06. Based on data presented by van Manen and van Oossanen [2], the fric- tional resistance coefficient will be approximately 0.002 and...Conference on Stability of Ships and Ocean Vehicles (Melbourne, Florida, 1994). 2. J.D. van Manen and P. van Oossanen, Principles of Naval Architecture, Volume

Predicting wind farm wake interaction with RANS: an investigation of the Coriolis force

DEFF Research Database (Denmark)

van der Laan, Paul; Hansen, Kurt Schaldemose; Sørensen, Niels N.

2015-01-01

A Reynolds-averaged Navier-Stokes code is used to simulate the interaction of two neighboring wind farms. The influence of the Coriolis force is investigated by modeling the atmospheric surface/boundary layer with three different methodologies. The results show that the Coriolis force is negligible...

Comparison of TOPEX/Poseidon Sea Level and Linear Model Results forced by Various Wind Products for the Tropical Pacific

Science.gov (United States)

Hackert, Eric C.; Busalacchi, Antonio J.

1997-01-01

The goal of this paper is to compare TOPEX/Posaidon (T/P) sea level with sea level results from linear ocean model experiments forced by several different wind products for the tropical Pacific. During the period of this study (October 1992 - October 1995), available wind products include satellite winds from the ERS-1 scatterometer product of [HALP 97] and the passive microwave analysis of SSMI winds produced using the variational analysis method (VAM) of [ATLA 91]. In addition, atmospheric GCM winds from the NCEP reanalysis [KALN 96], ECMWF analysis [ECMW94], and the Goddard EOS-1 (GEOS-1) reanalysis experiment [SCHU 93] are available for comparison. The observed ship wind analysis of FSU [STRI 92] is also included in this study. The linear model of [CANE 84] is used as a transfer function to test the quality of each of these wind products for the tropical Pacific. The various wind products are judged by comparing the wind-forced model sea level results against the T/P sea level anomalies. Correlation and RMS difference maps show how well each wind product does in reproducing the T/P sea level signal. These results are summarized in a table showing area average correlations and RMS differences. The large-scale low-frequency temporal signal is reproduced by all of the wind products, However, significant differences exist in both amplitude and phase on regional scales. In general, the model results forced by satellite winds do a better job reproducing the T/P signal (i.e. have a higher average correlation and lower RMS difference) than the results forced by atmospheric model winds.

Modulation of the erosion rate of an uplifting landscape by long-term climate change: An experimental investigation

Science.gov (United States)

Moussirou, Bérangé; Bonnet, Stéphane

2018-02-01

Whether or not climatic variations play a major role in setting the erosion rate of continental landscapes is a key factor in demonstrating the influence of climate on the tectonic evolution of mountain belts and understanding how clastic deposits preserved in sedimentary basins may record climatic variations. Here, we investigate how a change in precipitation influences the erosional dynamics of laboratory-scale landscapes that evolved under a combination of uplift and rainfall forcings. We consider here the impact of a decrease in the precipitation rate of finite duration on the erosive response of a landscape forced by a constant uplift and initially at a steady state (SS1). We performed several experiments with the same amplitude but different durations of precipitation decrease (Tp). We observe that the decrease in precipitation induces a phase of surface uplift of landscapes to a new steady state condition (SS2); however, the details of the uplift histories (timing, rate) differ between the experiments according to Tp. We also observe a decrease in the erosion rate induced by the precipitation change; however, the timing and amplitude of this decrease vary according to Tp, defining a delayed and damped erosion signal. Our data show that the landscape response to precipitation change is dictated by a critical water-to-rock ratio (ratio of precipitation over uplift) that likely corresponds to a geomorphic threshold. Our study suggests that variations in precipitation that occur at a geological time scale (> 106 years) may have a weak impact on the erosion of landscapes and on the delivery of siliciclastic material to large rivers and sedimentary basins.

The effect of vertical earthquake component on the uplift of the nuclear reactor building

International Nuclear Information System (INIS)

Kobayashi, Toshio

1986-01-01

During a strong earthquake, the base mat of a nuclear reactor building may be lifted partially by the response overturning moment. And it causes geometrical nonlinear interaction between the base mat and rock foundation beneath it. In order to avoid this uplift phenomena, the base mat and/or plan of the building is enlarged in some cases. These special design need more cost and/or time in construction. In the evaluation of the uplift phenomena, a parameter ''η'' named ''contact ratio'' is used defined as the ratio of compression stress zone area of base mat for total area of base mat. Usually this contact ratio is calculated under the combination of the maximum overturning moment obtained by the linear earthquake response analysis and the normal force by the gravity considering the effect of the vertical earthquake component. In this report, the effect of vertical earthquake component for the uplift phenomena is studied and it concludes that the vertical earthquake component gives little influence on the contact ratio. In order to obtain more reasonable contact retio, the nonlinear rocking analysis subjected to horizontal and vertical earthquake motions simultaneously is proposed in this report. As the second best method, the combination of the maximum overturning moment obtained by linear analysis and the normal force by only the gravity without the vertical earthquake effect is proposed. (author)

Effect of number of blades on aerodynamic forces on a straight-bladed Vertical Axis Wind Turbine

International Nuclear Information System (INIS)

Li, Qing'an; Maeda, Takao; Kamada, Yasunari; Murata, Junsuke; Furukawa, Kazuma; Yamamoto, Masayuki

2015-01-01

Small wind turbine performance and safety standard for straight-bladed Vertical Axis Wind Turbine (VAWT) have not been developed in the world because of the lack of fundament experimental data. This paper focuses on the evaluation of aerodynamic forces depending on several numbers of blades in wind tunnel experiment. In the present study, the test airfoil of blade is symmetry airfoil of NACA 0021 and the number of blades is from two to five. Pressure acting on the surface of rotor blade is measured during rotation by multiport pressure devices and transmitted to a stationary system through wireless LAN. And then, the aerodynamic forces (tangential force, normal force et al.) are discussed as a function of azimuth angle, achieving a quantitative analysis of the effect of numbers of blades. Finally, the loads are compared with the experimental data of six-component balance. As a result, it is clarified that the power coefficient decreases with the increase of numbers of blades. Furthermore, the power which is absorbed from wind by wind turbine mainly depends on upstream region of azimuth angle of θ = 0°∼180°. In this way, these results are very important for developing the simple design equations and applications for straight-bladed VAWT. - Highlights: • Aerodynamic forces are measured by not only torque meter but also six-component balance. • The pressure distribution on the surface of rotor blade is directly measured by multiport pressure devices. • The power coefficient decreases with the increase of numbers of blades. • The fluctuation amplitudes from six-component balance show larger value than the results of pressure distribution.

Analysis of vector wind change with respect to time for Vandenberg Air Force Base, California

Science.gov (United States)

Adelfang, S. I.

1978-01-01

A statistical analysis of the temporal variability of wind vectors at 1 km altitude intervals from 0 to 27 km altitude taken from a 10-year data sample of twice-daily rawinsode wind measurements over Vandenberg Air Force Base, California is presented.

Glacial isostatic uplift of the European Alps

Science.gov (United States)

Mey, Jürgen; Scherler, Dirk; Wickert, Andrew D.; Egholm, David L.; Tesauro, Magdala; Schildgen, Taylor F.; Strecker, Manfred R.

2016-01-01

Following the last glacial maximum (LGM), the demise of continental ice sheets induced crustal rebound in tectonically stable regions of North America and Scandinavia that is still ongoing. Unlike the ice sheets, the Alpine ice cap developed in an orogen where the measured uplift is potentially attributed to tectonic shortening, lithospheric delamination and unloading due to deglaciation and erosion. Here we show that ∼90% of the geodetically measured rock uplift in the Alps can be explained by the Earth’s viscoelastic response to LGM deglaciation. We modelled rock uplift by reconstructing the Alpine ice cap, while accounting for postglacial erosion, sediment deposition and spatial variations in lithospheric rigidity. Clusters of excessive uplift in the Rhône Valley and in the Eastern Alps delineate regions potentially affected by mantle processes, crustal heterogeneity and active tectonics. Our study shows that even small LGM ice caps can dominate present-day rock uplift in tectonically active regions. PMID:27830704

Forces and Moments on Flat Plates of Small Aspect Ratio with Application to PV Wind Loads and Small Wind Turbine Blades

OpenAIRE

Xavier Ortiz; David Rival; David Wood

2015-01-01

To improve knowledge of the wind loads on photovoltaic structures mounted on flat roofs at the high angles required in high latitudes, and to study starting flow on low aspect ratio wind turbine blades, a series of wind tunnel tests were undertaken. Thin flat plates of aspect ratios between 0.4 and 9.0 were mounted on a sensitive three-component instantaneous force and moment sensor. The Reynolds numbers varied from 6 × 10 4 to 2 × 10 5 . Measurements were made for angles of attack between 0°...

Test on the splitting failure capacity of the bottom rail due to uplift in partially anchored shear walls

OpenAIRE

Caprolu, Giuseppe; Girhammar, Ulf Arne; Källsner, Bo; Johnsson, Helena

2012-01-01

Källsner and Girhammar have developed a new plastic design method for wood-frame shear walls at ultimate limit state. The method is capable of calculating the load-carrying capacity of partially anchored shear walls, where the leading stud is not necessarily anchored against uplift. In fully anchored shear walls, the leading stud needs to be anchored using some kind of hold-downs to resist uplift and the bottom rail needs to be fixed by anchor bolts to resist horizontal shear forces. In parti...

Numerical Study on the Seismic Response of Structure with Consideration of the Behavior of Base Mat Uplift

Directory of Open Access Journals (Sweden)

Guo-Bo Wang

2017-01-01

Full Text Available The foundation might be separated from the supporting soil if the earthquake is big enough, which is known as base mat uplift. This paper proposed a simplified calculation model in which spring element is adopted to simulate the interaction between soil and structure. The load-deformation curve (F-D curve of the spring element can be designated to represent the base mat uplift, in which the pressure can be applied while tensile forces are not allowed. Key factors, such as seismic wave types, seismic wave excitation directions, seismic wave amplitudes, soil shear velocities, structure stiffness, and the ratio of structure height to width (H/B, were considered in the analysis. It is shown that (1 seismic wave type has significant influence on structure response due to different frequency components it contained; (2 the vertical input of seismic wave greatly affected structure response in vertical direction, while it has little impacts in horizontal direction; (3 base mat uplift is easier to take place in soil with higher shear velocity; (4 structure H/B value has complicated influence on base mat uplift. The outcome of this research is assumed to provide some references for the seismic design of the structure due to base mat uplift.

The impact of inertial forces on morphing wind turbine blade in vertical axis configuration

International Nuclear Information System (INIS)

Butbul, Jonathan; MacPhee, David; Beyene, Asfaw

2015-01-01

Highlights: • A novel flexible VAWT has been experimentally tested alongside numerically simulations. • Using FEA and CFD, direction of blade bending was predicted from inertial and aerodynamic forces. • High-speed camera footage has been used to validate the model. • The flexible VAWT was found to self-start in the majority of tests, while the rigid one did not. • It is suggested that flexible VAWTs can have improved performance in part-load applications. - Abstract: A novel flexible blade concept with the ability to morph and geometrically adapt to changing flow conditions has been proposed to improve part-load performance of horizontal-axis wind turbines. The extension of these benefits to a vertical axis wind turbine would make wind technology a more competitive player in the energy market. Both flexible and rigid wind turbine rotor blades for vertical axis application were modeled, designed, manufactured and tested. Their performances were tested in a low speed wind tunnel. The predicted magnitude and direction of blade morph was validated using a high speed camera as well as finite element analysis. The comparative results of straight rigid and straight morphing blades show that the coefficient of performance greatly depends on the tip speed ratio. Overall, the morphing blade has better performance at low RPMs, but the rigid blade performed better at high RPMs. It was observed that the flexible blade self-started in the majority of the experiments. At high RPM, the centrifugal force overwhelmed the lift force, bending the flexible blade out of phase in an undesired direction increasing drag and therefore reducing the coefficient of performance

Air Force Civil Engineer, Volume 16, Number 2, 2008

Science.gov (United States)

2008-01-01

factors to consider before deciding on a vegetative roof include wind and climate. Wind uplift resistance must be carefully evaluated. Green roofing...brighten any mood . He touched us all and left a part of him with us all. He is and will always be a great part of our EOD family.” TSgt Capra was

Effects from fully nonlinear irregular wave forcing on the fatigue life of an offshore wind turbine and its monopile foundation

DEFF Research Database (Denmark)

Schløer, Signe; Bredmose, Henrik; Bingham, Harry B.

2013-01-01

The effect from fully nonlinear irregular wave forcing on the fatigue life of the foundation and tower of an offshore wind turbine is investigated through aeroelastic calculations. Five representative sea states with increasing significant wave height are considered in a water depth of 40 m....... The waves are both linear and fully nonlinear irregular 2D waves. The wind turbine is the NREL 5-MW reference wind turbine. Fatigue analysis is performed in relation to analysis of the sectional forces in the tower and monopile. Impulsive excitation of the sectional force at the bottom of the tower is seen...

带键槽透水底板上举力特性模型试验研究%Model test on uplift force of pervious floor with a keyway

Institute of Scientific and Technical Information of China (English)

马斌; 马永磊; 邢仕强

2017-01-01

To protect the downstream river bed and bank slope of the high dam from the serious erosion by high—speed flood flow,which will endanger dam safety,it is necessary to build all kinds of stilling pond protective structures as the first line of defense for dam safety.The security of all types of stilling pond protective structures is the premise for the safety of high dam flood discharge.As the studies on downstream protective works of the high dam dig deeper,floors of different structural forms have been proposed,such as the stilling pond floor with a keyway and the pervious floor,to increase the stability of the stilling pond.The form of the stilling pond also transformed from the "passive protection" model to the "active protection" model.This paper studied the pervious floor with a keyway that combines "active protection" with "passive protection".A model test was conducted to analyze the uplift force in terms of the maximum value,probability density distribution,amplitude,and power spectrum.The results showed:In comparison with the floor with a keyway,increasing permeable holes can reduce the uplift force.The probability density distribution of the uplift force basically conforms to the normal distribution.The magnitude of the uplift force is reduced.The power spectral density is even closer to a low frequency.%为保护高坝下游河床和岸坡不受泄洪高速水流的严重冲刷,危及大坝安全,需修建各类消力塘防护结构以构建大坝安全第一道防线.各类消力塘防护结构的安全是高坝泄洪安全的前提保障.随着对高坝下游防护工程的研究不断深入,相继提出了带键槽消力塘底板、透水底板等不同结构形式的底板,增加消力塘的稳定性,消力塘形式也从“被动防护”模式向“主动防护”模式转变.对“主动�

Structure design and experimental appraisal of the drag force type vertical axis wind turbine

International Nuclear Information System (INIS)

Kim, Dong Keon; Keum, Jong Yoon; Yoon, Soon Hyun

2006-01-01

Experiments were conducted to estimate the performance of drag force type vertical axis wind turbine with an opening-shutting rotor. It was operated by the difference in drag force generated on both sides of the blades. The rotational speed was measured by a tachometer in a wind tunnel and the tunnel wind speed was measured by using a pitot-static tube and a micro manometer. The performance test for a prototype was accomplished by calculating power, power coefficient, torque coefficient from the measurement of torque and rpm by a dynamometer controller. Various design parameters, such as the number of blades(B), blade aspect ratio(W/R), angle of blades(α) and drag coefficient acting on a blade, were considered for optimal conditions. At the experiment of miniature model, maximum efficiency was found at N=15, α=60 .deg. and W/R=0.32. The measured test variables were power, torque, rotational speed, and wind speeds. The data presented are in the form of power and torque coefficients as a function of tip-speed ratio V/U. Maximum power was found in case of Ω=0.33, when the power and torque coefficient were 0.14 and 0.37 respectively. Comparing model test with prototype test, similarity law by advance ratio for vertical axis wind turbine was confirmed

Rapid Crustal Uplift at Birch Bay, Washington

Science.gov (United States)

Sherrod, B. L.; Kelsey, H. M.; Blakely, R. J.

2010-12-01

Geomorphology and coastal marsh stratigraphy suggest late Holocene uplift of the shoreline at Birch Bay, located northwest of Bellingham, Washington, during an earthquake on a shallow fault. LiDAR images show a raised, late Holocene shoreline along Birch Bay, with ~1 m of elevation difference between the modern shoreline and the inferred paleoshoreline. Commercial seismic reflection images reveal an anticline in Tertiary and possibly Quaternary deposits underlying Birch Bay. NW-trending magnetic anomalies are likely associated with the Birch Bay anticline and other nearby structures. Taken together, the geophysical data and lidar images suggest uplift of young deposits along a NW-trending blind reverse fault. Stratigraphy from Terrell Creek marsh, located just south of Birch Bay, shows freshwater peat buried by lower intertidal muds, indicating local submergence ~1300 yr BP. Stratigraphy of a 70-cm sediment core from Birch Bay marsh, sitting astride the anticline imaged with seismic reflection data, shows mud buried by detrital peat. One radiocarbon age from the core places the abrupt change from mud to peat prior to 1520-1700 yr BP. We divide fossil diatom assemblages straddling the mud-peat contact at Birch Bay into three zones. The oldest zone consists primarily of intertidal and marine diatoms, dominated by Paralia sulcata, Scoleoneis tumida, Grammataphora oceanica, and Gyrosigma balticum. An intermediate zone, beginning at the sharp contact between mud and overlying peat, consists of a mixture of brackish marsh and freshwater species, dominated by Diploneis interrupta, with lesser amounts of Aulacoseira sp., Pinnularia viridis, Eunotia pectinalis, and Paralia sulcata. A third and youngest zone lies in the upper half of the peat and is dominated by poorly preserved freshwater diatoms, mostly Aulacoseira cf. crassapuntata, Pinnularia viridis, P. maior, Eunotia pectinalis, and E. praerupta. Paleoecological inferences, based on distributions of modern diatoms

Thermal and Pressure Characterization of a Wind Tunnel Force Balance Using the Single Vector System. Experimental Design and Analysis Approach to Model Pressure and Temperature Effects in Hypersonic Wind Tunnel Research

Science.gov (United States)

Lynn, Keith C.; Commo, Sean A.; Johnson, Thomas H.; Parker, Peter A,

2011-01-01

Wind tunnel research at NASA Langley Research Center s 31-inch Mach 10 hypersonic facility utilized a 5-component force balance, which provided a pressurized flow-thru capability to the test article. The goal of the research was to determine the interaction effects between the free-stream flow and the exit flow from the reaction control system on the Mars Science Laboratory aeroshell during planetary entry. In the wind tunnel, the balance was exposed to aerodynamic forces and moments, steady-state and transient thermal gradients, and various internal balance cavity pressures. Historically, these effects on force measurement accuracy have not been fully characterized due to limitations in the calibration apparatus. A statistically designed experiment was developed to adequately characterize the behavior of the balance over the expected wind tunnel operating ranges (forces/moments, temperatures, and pressures). The experimental design was based on a Taylor-series expansion in the seven factors for the mathematical models. Model inversion was required to calculate the aerodynamic forces and moments as a function of the strain-gage readings. Details regarding transducer on-board compensation techniques, experimental design development, mathematical modeling, and wind tunnel data reduction are included in this paper.

Numerical modeling and experimental validation of seismic uplift pressure variations in cracked concrete dams

Energy Technology Data Exchange (ETDEWEB)

Javanmardi, F.; Leger, P. [Ecole Polytechnique, Montreal, PQ (Canada). Dept. of Civil, Mining and Geological Engineering; Tinawi, R. [Quebec Univ., Montreal, PQ (Canada)

2004-07-01

Concrete dams could sustain cracking and damage during maximum design earthquakes (MDE). Dam safety guidelines are established so that dams maintain a stable condition following MDE oscillatory motions. In this study, a theoretical model was developed to calculate the uplift pressure variations along concrete cracks with moving walls. The proposed model was verified using experimental crack test data. The model was applied in a finite element computer program for dynamic analysis of gravity dams considering hydro-mechanical water-crack coupling. An analysis of a typical 90 metre dam subjected to low and high frequency sinusoidal accelerations demonstrated that water can penetrate into part of a seismically initiated crack. Pressure tends to develop in a region close to the crack mouth, therefore detrimental effects for the global dam stability are unlikely to occur. The study showed that the seismic uplift force during the heel crack opening mode is small compared to the dam weight. This preliminary study suggests that the critical sliding safety factors (SSF) of the dam against downstream sliding could be computed by considering zero uplift pressure in the crack region subjected to tensile opening. 14 refs., 1 tab., 7 figs.

Measurements of the Aerodynamic Normal Forces on a 12-kW Straight-Bladed Vertical Axis Wind Turbine

Directory of Open Access Journals (Sweden)

Eduard Dyachuk

2015-08-01

Full Text Available The knowledge of unsteady forces is necessary when designing vertical axis wind turbines (VAWTs. Measurement data for turbines operating at an open site are still very limited. The data obtained from wind tunnels or towing tanks can be used, but have limited applicability when designing large-scale VAWTs. This study presents experimental data on the normal forces of a 12-kW straight-bladed VAWT operated at an open site north of Uppsala, Sweden. The normal forces are measured with four single-axis load cells. The data are obtained for a wide range of tip speed ratios: from 1.7 to 4.6. The behavior of the normal forces is analyzed. The presented data can be used in validations of aerodynamic models and the mechanical design for VAWTs.

Wind Tunnel Testing on Crosswind Aerodynamic Forces Acting on Railway Vehicles

Science.gov (United States)

Kwon, Hyeok-Bin; Nam, Seong-Won; You, Won-Hee

This study is devoted to measure the aerodynamic forces acting on two railway trains, one of which is a high-speed train at 300km/h maximum operation speed, and the other is a conventional train at the operating speed 100km/h. The three-dimensional train shapes have been modeled as detailed as possible including the inter-car, the upper cavity for pantograph, and the bogie systems. The aerodynamic forces on each vehicle of the trains have been measured in the subsonic wind tunnel with 4m×3m test section of Korea Aerospace Research Institute at Daejeon, Korea. The aerodynamic forces and moments of the train models have been plotted for various yaw angles and the characteristics of the aerodynamic coefficients has been discussed relating to the experimental conditions.

Preliminary Assessment of Potential Avian Interactions at Four Proposed Wind Energy Facilities on Vandenberg Air Force Base, California

Energy Technology Data Exchange (ETDEWEB)

2004-08-01

The United States Air Force (USAF) is investigating whether to install wind turbines to provide a supplemental source of electricity at Vandenberg Air Force Base (VAFB) near Lompoc, California. As part of that investigation, VAFB sought assistance from the U.S. Department of Energy's National Renewable Energy Laboratory (NREL) to provide a preliminary characterization of the potential risk to wildlife resources (mainly birds and bats) from wind turbine installations. With wind power development expanding throughout North America and Europe, concerns have surfaced over the number of bird fatalities associated with wind turbines. Guidelines developed for the wind industry by the National Wind Coordinating Committee (NWCC) recommend assessing potential impacts to birds, bats, and other potentially sensitive resources before construction. The primary purpose of an assessment is to identify potential conflicts with sensitive resources, to assist developers with identifying their permitting needs, and to develop strategies to avoid impacts or to mitigate their effects. This report provides a preliminary (Phase I) biological assessment of potential impacts to birds and bats that might result from construction and operation of the proposed wind energy facilities on VAFB.

Analytical solutions for peak and residual uplift resistance of pipelines

Energy Technology Data Exchange (ETDEWEB)

Nixon, J.F. [Nixon Geotech Ltd., Calgary, AB (Canada); Oswell, J.M. [Naviq Consulting Inc., Calgary, AB (Canada)

2010-07-01

Frost heave can occur on cold pipelines that traverse unfrozen, non permafrost terrain. The stresses experienced by the pipeline are partly a function of the strength of the soil on the non heaving side of the frozen-unfrozen interface. This paper proposed three analytical solutions to estimate the soil uplift resistance by considering the pipeline and soil to act similar to a strip footing, a punching shear failure, and by considering the formation of horizontal crack emanating from the spring line of the pipe. Peak uplift resistance and residual uplift resistance were discussed. Results for full scale pipe and for laboratory scale model pipes were presented, with particular reference to cover depth, temperature and crack width; and limits to residual uplift resistance. It was concluded that the peak uplift resistance and the residual uplift resistance are generally independent and controlled by different factors. The peak resistance is related directly to pipe diameter, and less strongly dependent on springline depth. It is also strongly dependent on soil temperature. However, the residual uplift resistance is strongly dependent on burial depth, weakly dependent on pipe displacement rate and also on soil temperature. 15 refs., 19 figs.

Transpressive mantle uplift at large offset oceanic transform faults

Science.gov (United States)

Maia, M.; Briais, A.; Brunelli, D.; Ligi, M.; Sichel, S. E.; Campos, T.

2017-12-01

Large-offset transform faults deform due to changes in plate motions and local processes. At the St. Paul transform, in the Equatorial Atlantic, a large body of ultramafic rocks composed of variably serpentinized and mylonitized peridotites is presently being tectonically uplifted. We recently discovered that the origin of the regional mantle uplift is linked to long-standing compressive stresses along the transform fault (1). A positive flower structure, mainly made of mylonitized mantle rocks, can be recognized on the 200 km large push-up ridge. Compressive earthquakes mechanisms reveal seismically active thrust faults on the southern flank of the ridge . The regional transpressive stress field affects a large portion of the ridge segment south of the transform, as revealed by the presence of faults and dykes striking obliquely to the direction of the central ridge axis. A smaller thrust, affecting recent sediments, was mapped south of this segment, suggesting a regional active compressive stress field. The transpressive stress field is interpreted to derive from the propagation of the Mid-Atlantic Ridge (MAR) segment into the transform domain as a response to the enhanced melt supply at the ridge axis. The propagation forced the migration and segmentation of the transform fault southward and the formation of restraining step-overs. The process started after a counterclockwise change in plate motion at 11 Ma initially resulting in extensive stress of the transform domain. A flexural transverse ridge formed in response. Shortly after plate reorganization, the MAR segment started to propagate southwards due to the interaction of the ridge and the Sierra Leone thermal anomaly. 1- Maia et al., 2016. Extreme mantle uplift and exhumation along a transpressive transform fault Nat. Geo. doi:10.1038/ngeo2759

Unsteady analysis on the instantaneous forces and moment arms acting on a novel Savonius-style wind turbine

International Nuclear Information System (INIS)

Roy, Sukanta; Ducoin, Antoine

2016-01-01

Highlights: • Two-dimensional unsteady simulations on a novel Savonius-style wind turbine. • Instantaneous behavior of drag and lift coefficients, and corresponding moment arms. • Effect of tip speed ratio on the instantaneous force coefficients and moments arms. • Effect of force coefficients and moment arms on the instantaneous moment and power. • Analysis of power and moment coefficients at different tip speed ratios. - Abstract: This paper aims to present a transient analysis on the forces acting on a novel two-bladed Savonius-style wind turbine. Two-dimensional unsteady Reynolds Averaged Navier Stokes equations are solved using shear stress transport k–ω turbulence model at a Reynolds number of 1.23 × 10"5. The instantaneous longitudinal drag and lateral lift forces acting on each of the blades and their acting points are calculated. The corresponding moment arms responsible for the torque generation are obtained. Further, the effect of tip speed ratio on the force coefficients, moment arms and overall turbine performances are observed. Throughout the paper, the obtained results for the new design are discussed with reference to conventional semi-circular design of Savonius turbines. A significant performance improvement is achieved with the new design due to its increased lift and moment arm contribution as compared to the conventional design. More interestingly, the present study sets a platform for future aerodynamic research and improvements for Savonius-style wind turbines.

Vandenberg Air Force Base Upper Level Wind Launch Weather Constraints

Science.gov (United States)

Shafer, Jaclyn A.; Wheeler, Mark M.

2012-01-01

The 30th Operational Support Squadron Weather Flight (30 OSSWF) provides comprehensive weather services to the space program at Vandenberg Air Force Base (VAFB) in California. One of their responsibilities is to monitor upper-level winds to ensure safe launch operations of the Minuteman III ballistic missile. The 30 OSSWF tasked the Applied Meteorology Unit (AMU) to analyze VAFB sounding data with the goal of determining the probability of violating (PoV) their upper-level thresholds for wind speed and shear constraints specific to this launch vehicle, and to develop a tool that will calculate the PoV of each constraint on the day of launch. In order to calculate the probability of exceeding each constraint, the AMU collected and analyzed historical data from VAFB. The historical sounding data were retrieved from the National Oceanic and Atmospheric Administration Earth System Research Laboratory archive for the years 1994-2011 and then stratified into four sub-seasons: January-March, April-June, July-September, and October-December. The maximum wind speed and 1000-ft shear values for each sounding in each subseason were determined. To accurately calculate the PoV, the AMU determined the theoretical distributions that best fit the maximum wind speed and maximum shear datasets. Ultimately it was discovered that the maximum wind speeds follow a Gaussian distribution while the maximum shear values follow a lognormal distribution. These results were applied when calculating the averages and standard deviations needed for the historical and real-time PoV calculations. In addition to the requirements outlined in the original task plan, the AMU also included forecast sounding data from the Rapid Refresh model. This information provides further insight for the launch weather officers (LWOs) when determining if a wind constraint violation will occur over the next few hours on day of launch. The interactive graphical user interface (GUI) for this project was developed in

Control of paleoshorelines by trench forebulge uplift, Loyalty Islands

Science.gov (United States)

Dickinson, William R.

2013-07-01

Unlike most tropical Pacific islands, which lie along island arcs or hotspot chains, the Loyalty Islands between New Caledonia and Vanuatu owe their existence and morphology to the uplift of pre-existing atolls on the flexural forebulge of the New Hebrides Trench. The configuration and topography of each island is a function of distance from the crest of the uplifted forebulge. Both Maré and Lifou are fully emergent paleoatolls upon which ancient barrier reefs form highstanding annular ridges that enclose interior plateaus representing paleolagoon floors, whereas the partially emergent Ouvea paleoatoll rim flanks a drowned remnant lagoon. Emergent paleoshoreline features exposed by island uplift include paleoreef flats constructed as ancient fringing reefs built to past low tide levels and emergent tidal notches incised at past high tide levels. Present paleoshoreline elevations record uplift rates of the islands since last-interglacial and mid-Holocene highstands in global and regional sea levels, respectively, and paleoreef stratigraphy reflects net Quaternary island emergence. The empirical uplift rates vary in harmony with theoretical uplift rates inferred from the different positions of the islands in transit across the trench forebulge at the trench subduction rate. The Loyalty Islands provide a case study of island environments controlled primarily by neotectonics.

Uplift, Emergence, and Subsidence of the Gorda Escarpment Basement Ridge Offshore Cape Mendocino, CA

Science.gov (United States)

Hoover, Susan M.; Tréhu, Anne M.

2017-12-01

The Gorda Escarpment is a topographic step that characterizes the south side of the Mendocino Transform Fault east of 126oW and forms the northern edge of the Vizcaino Block. Seismic reflection data suggest that the basement beneath the northern edge of the Vizcaino is composed of east-west trending slivers of oceanic crust that form a 15 km wide band of buried ridges we call the Gorda Escarpment Basement Ridge (GEBR) to distinguish it from the northwest-trending basement structure that characterizes most of the Vizcaino Block. The history of uplift and subsidence of the GEBR is reconstructed by combining the seismic reflection profiles with age and lithological constraints from ODP Site 1022, gravity cores, and grab samples from the northern face of the Escarpment recovered using a remotely operated vehicle. Uplift of the GEBR began prior to 6 Ma, and it was above sea level 3.7-2.5 Ma. GEBR uplift and emergence coincided with sediment deposition on the southern flank of the GEBR that we interpret as indicative of strong upwelling and turbulence in the lee of a shallow ridge and island chain. A bright reflection, interpreted to be a sill, is observed south of the shallowest part of the GEBR. We speculate that this sill may reflect a larger, hidden intrusion at depth and that thermal expansion of the crust combined with tectonic forces to drive enhanced uplift of this segment of the plate boundary. The GEBR has been subsiding since 2.7 Ma, and its shallowest point is now 1,400 m below sea level.

F-theory uplifts and GUTs

International Nuclear Information System (INIS)

Blumenhagen, Ralph; Jurke, Benjamin; Grimm, Thomas W.; Weigand, Timo

2009-01-01

We study the F-theory uplift of Type IIB orientifold models on compact Calabi-Yau threefolds containing divisors which are del Pezzo surfaces. We consider two examples defined via del Pezzo transitions of the quintic. The first model has an orientifold projection leading to two disjoint O7-planes and the second involution acts via an exchange of two del Pezzo surfaces. The two uplifted fourfolds are generically singular with minimal gauge enhancements over a divisor and, respectively, a curve in the non-Fano base. We study possible further degenerations of the elliptic fiber leading to F-theory GUT models based on subgroups of E 8 .

Stochastic modeling of lift and drag dynamics to obtain aerodynamic forces with local dynamics on rotor blade under unsteady wind inflow

International Nuclear Information System (INIS)

Luhur, M.R.

2014-01-01

This contribution provides the development of a stochastic lift and drag model for an airfoil FX 79-W-151A under unsteady wind inflow based on wind tunnel measurements. Here we present the integration of the stochastic model into a well-known standard BEM (Blade Element Momentum) model to obtain the corresponding aerodynamic forces on a rotating blade element. The stochastic model is integrated as an alternative to static tabulated data used by classical BEM. The results show that in comparison to classical BEM, the BEM with stochastic approach additionally reflects the local force dynamics and therefore provides more information on aerodynamic forces that can be used by wind turbine simulation codes. (author)

Stochastic Modeling of Lift and Drag Dynamics to Obtain Aerodynamic Forces with Local Dynamics on Rotor Blade under Unsteady Wind Inflow

Directory of Open Access Journals (Sweden)

Muhammad Ramzan Luhur

2014-01-01

Full Text Available This contribution provides the development of a stochastic lift and drag model for an airfoil FX 79-W-151A under unsteady wind inflow based on wind tunnel measurements. Here we present the integration of the stochastic model into a well-known standard BEM (Blade Element Momentum model to obtain the corresponding aerodynamic forces on a rotating blade element. The stochastic model is integrated as an alternative to static tabulated data used by classical BEM. The results show that in comparison to classical BEM, the BEM with stochastic approach additionally reflects the local force dynamics and therefore provides more information on aerodynamic forces that can be used by wind turbine simulation codes

Investigation on dynamic response with foundation uplift

International Nuclear Information System (INIS)

Ohtomo, Keizo; Iwatate, Hisahiro

1987-01-01

In order to rationalize the aseismatic design of nuclear power stations, it is necessary to elucidate the characteristics of effective input when the earthquake motion for the design is inputted in the foundations of nuclear power stations. In this study, among the research subjects concerning the reduction of effective earthquake input, regarding the uplift of foundations, its response characteristics and the method of the rational evaluation of earth contact ratio were experimentally examined, and the method of analysis which can evaluate the damping effect due to the uplift was proposed. The experimental method is reported. It was found that accompanying the uplift of foundations, vertical motion was induced, and horizontal motion showed nonlinear response. It was confirmed that the nonlinear response accompanying the uplift can be approximately evaluated by the conventional analysis technique using the S-R model. The current equation for evaluating earth contact ratio is adequate for a soft ground model, and tends to undervaluate for a hard ground model. The S-R analysis model introducing the experimentally obtained characteristics in the dampling coefficient of a nonlinear rocking spring was newly made. (Kako, I.)

Uplift of quaternary shorelines in eastern Patagonia: Darwin revisited

Science.gov (United States)

Pedoja, Kevin; Regard, Vincent; Husson, Laurent; Martinod, Joseph; Guillaume, Benjamin; Fucks, Enrique; Iglesias, Maximiliano; Weill, Pierre

2011-04-01

During his journey on the Beagle, Darwin observed the uniformity in the elevation of coastal Eastern Patagonia along more than 2000 km. More than one century later, the sequences of Quaternary shorelines of eastern Patagonia have been described and their deposits dated but not yet interpreted in terms of geodynamics. Consequently, we i) mapped the repartition of the Quaternary coastal sequences in Argentinean Patagonia, ii) secured accurate altitudes of shoreline angles associated with erosional morphologies (i.e. marine terraces and notches), iii) took into account previous chrono-stratigraphical interpretations in order to calculate mean uplift rates since ~ 440 ka (MIS 11) and proposed age ranges for the higher and older features (up to ~ 180 m), and iv) focused on the Last Interglacial Maximum terrace (MIS 5e) as the best constrained marine terrace (in terms of age and altitude) in order to use it as a tectonic benchmark to quantify uplift rates along the entire passive margin of Eastern South America. Our results show that the eastern Patagonia uplift is constant through time and twice the uplift of the rest of the South American margin. We suggest that the enhanced uplift along the eastern Patagonian coast that interested Darwin during his journey around South America on the Beagle could originate from the subduction of the Chile ridge and the associated dynamic uplift.

Wind loads on stand-off photovoltaic systems on pitched roofs

NARCIS (Netherlands)

Geurts, C.P.W.; Blackmore, P.A.

2013-01-01

Stand-off photovoltaic systems are a popular measure for retrofitting of existing pitched roofs. Panels are generally mounted parallel to the existing roof coverings, usually roofing tiles. Full scale and wind tunnel experiments have been performed to determine the net uplift loads on these systems,

Variability of sea ice deformation rates in the Arctic and their relationship with basin-scale wind forcing

Directory of Open Access Journals (Sweden)

A. Herman

2012-12-01

Full Text Available The temporal variability of the moments of probability distribution functions (pdfs of total sea ice deformation rates in the Arctic is analyzed in the context of the basin-scale wind forcing acting on the ice. The pdfs are estimated for 594 satellite-derived sea ice deformation maps from 11 winter seasons between 1996/1997 and 2007/2008, provided by the RADARSAT Geophysical Processor System. The temporal scale analyzed equals 3 days. The moments of the pdfs, calculated for a range of spatial scales (12.5–900 km, have two dominating components of variability: a seasonal cycle, with deformation rates decreasing throughout winter towards a minimum in March; and a short-term, synoptic variability, strongly correlated with the area-averaged magnitude of the wind stress over the Arctic, estimated based on the NCEP-DOE Reanalysis-2 data (correlation coefficient of 0.71 for the mean deformation rate. Due to scaling properties of the moments, logarithms of higher moments are strongly correlated with the wind stress as well. Exceptions are observed only at small spatial scales, as a result of extreme deformation events, not directly associated with large-scale wind forcing. By repeating the analysis within regions of different sizes and locations, we show that the wind–ice deformation correlation is largest at the basin scale and decreases with decreasing size of the area of study. Finally, we suggest that a positive trend in seasonally averaged correlation between sea ice deformation rates and the wind forcing, present in the analyzed data, may be related to an observed decrease in the multi-year ice area in the Arctic, indicating possibly even stronger correlations in the future.

Competition between uplift and transverse sedimentation in an experimental delta

Science.gov (United States)

Grimaud, Jean-Louis; Paola, Chris; Ellis, Chris

2017-07-01

Mass is commonly injected into alluvial systems either laterally by transport from source regions or vertically from below via local uplift. We report results on the competition between these two fundamental processes, using an experimental basin with a deformable substrate. The lateral supply is via two alluvial fans on orthogonal walls of the basin; the uplifting region is downstream of one of the fans (axial) and opposite to the other (transverse). We show that the presence of a transverse sediment input increases the erosion rate of the uplifting region by pushing the mixing zone between the two alluvial sources against the uplifting mass. However, increase in sediment delivery to the transverse fan does not cause a proportional increase in erosion rate of the uplifting region. Instead, the system reaches a steady state balance between uplift and erosion induced by the transverse fan, such that there is no change in the total mass above the active alluvial surface—a lateral analog of the classical steady state between vertical erosion and uplift. We also show that the mixing zone is instrumental in limiting upstream aggradation and funneling sediments to the shore, resulting in limited river lateral mobility and increased shoreline progradation. Hence, the interaction between alluvial sources buffers river erosion and leads to consistent deviations from predictions of the area of influence of each fan based on simple mass-balance arguments. In the Ganges-Brahmaputra-Meghna delta, we suggest that similar dynamics help stabilize the Brahmaputra River course in the Jamuna Valley during Holocene time.

Burial, Uplift and Exhumation History of the Atlantic Margin of NE Brazil

Science.gov (United States)

Japsen, Peter; Bonow, Johan M.; Green, Paul F.; Cobbold, Peter R.; Chiossi, Dario; Lilletveit, Ragnhild

2010-05-01

We have undertaken a regional study of landscape development and thermo-tectonic evo-lution of NE Brazil. Our results reveal a long history of post-Devonian burial and exhuma-tion across NE Brazil. Uplift movements just prior to and during Early Cretaceous rifting led to further regional denudation, to filling of rift basins and finally to formation of the Atlantic margin. The rifted margin was buried by a km-thick post-rift section, but exhumation began in the Late Cretaceous as a result of plate-scale forces. The Cretaceous cover probably extended over much of NE Brazil where it is still preserved over extensive areas. The Late Cretaceous exhumation event was followed by events in the Paleogene and Neogene. The results of these events of uplift and exhumation are two regional peneplains that form steps in the landscape. The plateaux in the interior highlands are defined by the Higher Surface at c. 1 km above sea level. This surface formed by fluvial erosion after the Late Cretaceous event - and most likely after the Paleogene event - and thus formed as a Paleogene pene-plain near sea level. This surface was reburied prior to the Neogene event, in the interior by continental deposits and along the Atlantic margin by marine and coastal deposits. Neo-gene uplift led to reexposure of the Palaeogene peneplain and to formation of the Lower Surface by incision along rivers below the uplifted Higher Surface that characterise the pre-sent landscape. Our results show that the elevated landscapes along the Brazilian margin formed during the Neogene, c. 100 Myr after break-up. Studies in West Greenland have demonstrated that similar landscapes formed during the late Neogene, c. 50 Myr after break-up. Many passive continental margins around the world are characterised by such elevated plateaus and it thus seems possible, even likely, that they may also post-date rifting and continental separation by many Myr.

Strongly-sheared wind-forced currents in the nearshore regions of the central Southern California Bight

Science.gov (United States)

Noble, Marlene A.; Rosenberger, Kurt; Robertson, George L.

2015-01-01

Contrary to many previous reports, winds do drive currents along the shelf in the central portion of the Southern California Bight (SCB). Winds off Huntington Beach CA are the dominant forcing for currents over the nearshore region of the shelf (water depths less than 20 m). Winds control about 50–70% of the energy in nearshore alongshelf surface currents. The wind-driven current amplitudes are also anomalously high. For a relatively weak 1 dyne/cm2 wind stress, the alongshelf surface current amplitudes in this region can reach 80 cm/s or more. Mid-depth current amplitudes for the same wind stress are around 30–40 cm/s. These wind-driven surface current amplitudes are much larger than previously measured over other nearshore shelf regions, perhaps because this program is one of the few that measured currents within a meter of the surface. The near-bed cross-shelf currents over the nearshore region of the Huntington Beach shelf have an Ekman response to winds in that they upwell (downwell) for down (up) coast winds. This response disappears further offshore. Hence, there is upwelling in the SCB, but it does not occur across the entire shelf. Subthermocline water in the nearshore region that may contain nutrients and plankton move onshore when winds are southeastward, but subthermocline water over the shelf break is not transported to the beach. The currents over the outer shelf are not predominately controlled by winds, consistent with previous reports. Instead, they are mainly driven by cross-shelf pressure gradients that are independent of local wind stress.

Constraints on Dbar uplifts

International Nuclear Information System (INIS)

Alwis, S.P. de

2016-01-01

We discuss constraints on KKLT/KKLMMT and LVS scenarios that use anti-branes to get an uplift to a deSitter vacuum, coming from requiring the validity of an effective field theory description of the physics. We find these are not always satisfied or are hard to satisfy.

Wind Forced Variability in Eddy Formation, Eddy Shedding, and the Separation of the East Australian Current

Science.gov (United States)

Bull, Christopher Y. S.; Kiss, Andrew E.; Jourdain, Nicolas C.; England, Matthew H.; van Sebille, Erik

2017-12-01

The East Australian Current (EAC), like many other subtropical western boundary currents, is believed to be penetrating further poleward in recent decades. Previous observational and model studies have used steady state dynamics to relate changes in the westerly winds to changes in the separation behavior of the EAC. As yet, little work has been undertaken on the impact of forcing variability on the EAC and Tasman Sea circulation. Here using an eddy-permitting regional ocean model, we present a suite of simulations forced by the same time-mean fields, but with different atmospheric and remote ocean variability. These eddy-permitting results demonstrate the nonlinear response of the EAC to variable, nonstationary inhomogeneous forcing. These simulations show an EAC with high intrinsic variability and stochastic eddy shedding. We show that wind stress variability on time scales shorter than 56 days leads to increases in eddy shedding rates and southward eddy propagation, producing an increased transport and southward reach of the mean EAC extension. We adopt an energetics framework that shows the EAC extension changes to be coincident with an increase in offshore, upstream eddy variance (via increased barotropic instability) and increase in subsurface mean kinetic energy along the length of the EAC. The response of EAC separation to regional variable wind stress has important implications for both past and future climate change studies.

Regional cenozoic uplift and subsidence events in the southeastern North Sea

Energy Technology Data Exchange (ETDEWEB)

Jordt, H.

1995-12-31

The Paleocene topography of the Fennoscandian Shield is indicated by outbuilding towards the Central Trough and the Ringkoebing-Fyn High. From Eocene until Pliocene time three events of relative vertical movements are indicated by changes in outbuilding directions and reflection termination patterns in the central North Sea. The firs event of uplift was in the Eocene and resulted in relative uplift of the Mid North Sea High and contemporary subsidence east of it, indicated by a change in outbuilding from north to west. A second event of uplift is indicated to the north of the study area at the Eocene-Oligocene boundary by renewed southward outbuilding in the Norwegian-Danish Basin. In Miocene until Early Pliocene time a relatively stationary, almost east-west striking, basin margin was probably located to the north along the Tornquist Zone as indicated by the continued outbuilding towards the Ringkoebing-Fyn High. A third event of relative uplift is indicated east of the study area by changes in the Pliocene outbuilding pattern. After the first event of uplift it appears that the deepest parts of the Eocene North Sea Basin was located more easterly than the deepest part are today. Apparently the two latest uplift events north and east of the study area were related to movements of, or along the Tornquist Zone or to regional uplift of the Fennoscandian Shield finally resulting in the present-day configuration of the North Sea. (au) 11 refs.

Real-time POD-CFD Wind-Load Calculator for PV Systems

Energy Technology Data Exchange (ETDEWEB)

Huayamave, Victor [Centecorp; Divo, Eduardo [Centecorp; Ceballos, Andres [Centecorp; Barriento, Carolina [Centecorp; Stephen, Barkaszi [FSEC; Hubert, Seigneur [FSEC

2014-03-21

The primary objective of this project is to create an accurate web-based real-time wind-load calculator. This is of paramount importance for (1) the rapid and accurate assessments of the uplift and downforce loads on a PV mounting system, (2) identifying viable solutions from available mounting systems, and therefore helping reduce the cost of mounting hardware and installation. Wind loading calculations for structures are currently performed according to the American Society of Civil Engineers/ Structural Engineering Institute Standard ASCE/SEI 7; the values in this standard were calculated from simplified models that do not necessarily take into account relevant characteristics such as those from full 3D effects, end effects, turbulence generation and dissipation, as well as minor effects derived from shear forces on installation brackets and other accessories. This standard does not include provisions that address the special requirements of rooftop PV systems, and attempts to apply this standard may lead to significant design errors as wind loads are incorrectly estimated. Therefore, an accurate calculator would be of paramount importance for the preliminary assessments of the uplift and downforce loads on a PV mounting system, identifying viable solutions from available mounting systems, and therefore helping reduce the cost of the mounting system and installation. The challenge is that although a full-fledged three-dimensional computational fluid dynamics (CFD) analysis would properly and accurately capture the complete physical effects of air flow over PV systems, it would be impractical for this tool, which is intended to be a real-time web-based calculator. CFD routinely requires enormous computation times to arrive at solutions that can be deemed accurate and grid-independent even in powerful and massively parallel computer platforms. This work is expected not only to accelerate solar deployment nationwide, but also help reach the SunShot Initiative goals

Can footwall unloading explain late Cenozoic uplift of the Sierra Nevada crest?

Science.gov (United States)

Thompson, G.A.; Parsons, T.

2009-01-01

Globally, normal-fault displacement bends and warps rift flanks upwards, as adjoining basins drop downwards. Perhaps the most evident manifestations are the flanks of the East African Rift, which cuts across the otherwise minimally deformed continent. Flank uplift was explained by Vening Meinesz (1950, Institut Royal Colonial Belge, Bulletin des Seances, v. 21, p. 539-552), who recognized that isostasy should cause uplift of a normal-faulted footwall and subsidence of its hanging wall. Uplift occurs because slip on a dipping normal fault creates a broader root of less-dense material beneath the footwall, and a narrowed one beneath the hanging wall. In this paper, we investigate the potential influence of this process on the latest stages of Sierra Nevada uplift. Through theoretical calculations and 3D finite element modelling, we find that cumulative slip of about 4km on range-front faults would have produced about 1.3km peak isostatic uplift at the ridge crest. Numerical models suggest that the zone of uplift is narrow, with the width controlled by bending resistance of the seismogenic crust. We conclude that footwall unloading cannot account for the entire elevation of the Sierran crest above sea level, but if range-front faulting initiated in an already elevated plateau like the adjacent Basin and Range Province, then a hybrid model of pre-existing regional uplift and localized footwall unloading can account for the older and newer uplift phases suggested by the geologic record.

Wind: new wind markets

International Nuclear Information System (INIS)

Cameron, A.

2005-01-01

The June 2005 edition of 'Wind Force 12' suggests that wind could generate 12% of global electricity requirements by 2020. But what moves a potential market into an emerging one? Geographical factors include a good wind resource, plenty of open space and the ability to get the generated electricity to end-users. A country's political framework is equally important, with fixed price systems, renewable quota systems and political will all playing a part. Some potential wind markets around the world are thought to have the conditions necessary to become key players in the wind industry. The emerging markets in countries such as Australia, Brazil, Canada, France, Japan and the Philippines are highlighted as examples

Experimental studies of pipeline uplift resistance in frozen ground

Energy Technology Data Exchange (ETDEWEB)

Liu, B.; Crooks, J. [Golder Associates Ltd., Calgary, AB (Canada); Nixon, J.F. [Nixon Geotech Ltd., Calgary, AB (Canada); Zhou, J. [TransCanada PipeLines Ltd., Calgary, AB (Canada)

2004-07-01

Gas pipelines buried in permafrost are subjected to the mechanisms of frost heave and thaw settlement which induce movement in the pipe. The magnitude of loads depend on the relative displacement and the load-displacement characteristics of the surrounding soils. This paper presented the results of laboratory tests that investigated the geomechanical properties and uplift resistance of frozen Calgary silt. Compacted soil was frozen 24 hours prior to the uplift testing. A thick-wall steel pipe was laid down and more soil was subsequently placed and compacted around and above the pipe until the desired burial depth was achieved. The temperature of the frozen soil was monitored along with deformations of the soil surface in order to determine the impact of loading rate, ice content and freezing direction. The geomechanical tests included triaxial compression tests as well as tensile and creep tests. The stiffness, tensile strain limits and time dependent behaviour of the frozen soil were also defined. The issue of crack development in the frozen soil was addressed and a numerical model was developed based on measured load-displacement relationships and geomechanical properties of the frozen soil. Bilinear stress-strain relationships were consistently noted for the frozen samples under triaxial compression. The stress-strain behaviour was found to be independent of the confining stress. The measured tensile limits were found to be in good agreement with published literature. Peak uplift resistance and post-peak decreases were consistently noted in the uplift resistance. Tensile fractures were observed vertically above the crown of the pipe. Uplift resistance was highly affected by the loading rate, but the load-displacement curve prior to the peak was not affected by radial freezing or ice lenses. A new peak uplift resistance was reached following the freeze/thaw cycle, suggesting the healing of the tensile fractures. 9 refs., 1 tab., 11 figs.

Forced pitch motion of wind turbines

Science.gov (United States)

Leble, V.; Barakos, G.

2016-09-01

The possibility of a wind turbine entering vortex ring state during pitching oscillations is explored in this paper. The aerodynamic performance of the rotor was computed using the Helicopter Multi-Block flow solver. This code solves the Navier-Stokes equations in integral form using the arbitrary Lagrangian-Eulerian formulation for time-dependent domains with moving boundaries. A 10-MW wind turbine was put to perform yawing and pitching oscillations suggesting the partial vortex ring state during pitching motion. The results also show the strong effect of the frequency and amplitude of oscillations on the wind turbine performance.

Forced pitch motion of wind turbines

International Nuclear Information System (INIS)

Leble, V; Barakos, G

2016-01-01

The possibility of a wind turbine entering vortex ring state during pitching oscillations is explored in this paper. The aerodynamic performance of the rotor was computed using the Helicopter Multi-Block flow solver. This code solves the Navier-Stokes equations in integral form using the arbitrary Lagrangian-Eulerian formulation for time-dependent domains with moving boundaries. A 10-MW wind turbine was put to perform yawing and pitching oscillations suggesting the partial vortex ring state during pitching motion. The results also show the strong effect of the frequency and amplitude of oscillations on the wind turbine performance. (paper)

Aerosol removal due to precipitation and wind forcings in Milan urban area

Science.gov (United States)

Cugerone, Katia; De Michele, Carlo; Ghezzi, Antonio; Gianelle, Vorne

2018-01-01

Air pollution represents a critical issue in Milan urban area (Northern Italy). Here, the levels of fine particles increase, overcoming the legal limits, mostly in wintertime, due to favourable calm weather conditions and large heating and vehicular traffic emissions. The main goal of this work is to quantify the aerosol removal effect due to precipitation at the ground. At first, the scavenging coefficients have been calculated for aerosol particles with diameter between 0.25 and 3 μm. The average values of this coefficient vary between 2 ×10-5 and 5 ×10-5 s-1. Then, the aerosol removal induced separately by precipitation and wind have been compared through the introduction of a removal index. As a matter of fact, while precipitation leads to a proper wet scavenging of the particles from the atmosphere, high wind speeds cause enhanced particle dispersion and dilution, that locally bring to a tangible decrease of aerosol particles' number. The removal triggered by these two forcings showed comparable average values, but different trends. The removal efficiency of precipitation lightly increases with the increase of particle diameters and vice versa happens with strong winds.

Wind forces and related saltation transport

NARCIS (Netherlands)

Leenders, J.K.; van Boxel, J.H.; Sterk, G.

2005-01-01

The effect of several wind characteristics on sand transport was studied in three experiments in north Burkina Faso, West Africa. The first experiment is used to analyse the relation between wind speed and shear stress fluctuations across height. The second experiment is used to study the relation

Along-wind response of a wind turbine tower with blade coupling subjected to rotationally sampled wind loading

Energy Technology Data Exchange (ETDEWEB)

Murtagh, P J; Basu, B; Broderick, B M [Department of Civil, Structural and Environmental Engineering, Trinity College, Dublin (Ireland)

2005-07-15

This paper proposes an approach to investigate the along-wind forced vibration response of a wind turbine tower and rotating blades assembly subjected to rotationally sampled stationary wind loading. The wind turbine assembly consists of three rotating rotor blades connected to the top of a flexible annular tower, constituting a multi-body dynamic entity. The tower and rotating blades are each modelled as discretized multi-degree-of-freedom (MDOF) entities, allowing the free vibration characteristics of each to be obtained using a discrete parameter approach. The free vibration properties of the tower include the effect of a rigid mass at the top, representing the nacelle, and those of the blade include the effects of centrifugal stiffening due to rotation and blade gravity loadings. The blades are excited by drag force time-histories derived from discrete Fourier transform (DFT) representations of rotationally sampled wind turbulence spectra. Blade response time-histories are obtained using the mode acceleration method, which allows for the quantification of base shear forces due to flapping for the three blades to be obtained. This resultant base shear is imparted into the top of the tower. Wind drag loading on the tower is also considered, with a series of spatially correlated nodal force time-histories being derived using DFTs of wind force spectra. The tower/nacelle is then coupled with the rotating blades by combining their equations of motion and solving for the displacement at the top of the tower under compatibility conditions in the frequency domain. An inverse Fourier transform of the frequency domain response yields the response time-history of the coupled system. The response of an equivalent system that does not consider the blade/tower interaction is also investigated, and the results are compared. (Author)

The Sedimentary History of Southern Central Crete: Implications for Neogene Uplift

Science.gov (United States)

Kröger, K.; Brachert, T. C.; Reuter, M.

2003-04-01

The tectonic setting of Crete was largely extensional since Lower Miocene uplift and exhumation of HP/LT rocks. Erosion of uplifted areas resulted in the deposition of terrestrial to marine sediments in the Messara and Iraclion Basins. There are several concurring models that discuss Late Neogene uplift of the basinal margins. Neogene near shore sediments in the south of the Messara Basin record fault movements contemporaneous to sedimentation and sedimentary input from the hinterland. Therefore they provide information on the paleogeographic situation and the resulting amount of subsidence and uplift of mountain areas since the Upper Miocene. The studied sediments consist of terrestrial to shallow marine, floodplain related sediments of the Upper Miocene Ambelouzos Formation that are overlain by platform limestones of the Upper Miocene Varvara Formation. In the Messara Basin these units are overlain by the Pliocene Kourtes Formation. The stratigraphic architecture of these deposits indicates fragmentation of the basinal margin. Proximal boulder conglomerates and reworked blocks of the Ambelouzos formation indicate fault activity during the deposition of the Varvara Formation. Contents of terrigenous clastics, provided by rivers and distributed by longshore currents, are high in the Ambelouzos and the lower Varvara Formations but decrease rapidly upsection within the Varvara Formation. This indicates drowning of the fault bounded blocks and little topography of the hinterland (Asteroussia Mountains) at that time. The Pliocene marls at the southern margin of the Messara Basin contain lithoclasts of the Upper Miocene limestones and thus indicate uplift of the carbonate platform. The modern topographic elevation of formerly drowned fault bounded blocks requires a minimum uplift of 400m. Main uplift occurred at approximately orthogonal NW-SE and SW-NE striking normal to oblique faults. The present elevation of the Asteroussia Mountains indicates net uplift of at least

Determination of aerodynamic damping and force coefficients of filleted twin cables in dry conditions through passive-dynamic wind tunnel tests

DEFF Research Database (Denmark)

Mattiello, E.; Eriksen, M. B.; Georgakis, Christos T.

/FORCE Technology Climatic Wind Tunnel facility. The measured aerodynamic damping of the twin-cable arrangement in dry conditions was compared to the values obtained from full-scale monitoring and from an analytical model using static force coefficients. The comparison revealed broad agreement in the investigated...... Re range, as did the force coefficients obtained from dynamic and static tests....

The role of remote wind forcing in the subinertial current variability in the central and northern parts of the South Brazil Bight

Science.gov (United States)

Dottori, Marcelo; Castro, Belmiro Mendes

2018-05-01

Data analysis of continental shelf currents and coastal sea level, together with the application of a semi-analytical model, are used to estimate the importance of remote wind forcing on the subinertial variability of the current in the central and northern areas of the South Brazil Bight. Results from both the data analysis and from the semi-analytical model are robust in showing subinertial variability that propagates along-shelf leaving the coast to the left in accordance with theoretical studies of Continental Shelf Waves (CSW). Both the subinertial variability observed in along-shelf currents and sea level oscillations present different propagation speeds for the narrow northern part of the SBB ( 6-7 m/s) and the wide central SBB region ( 11 m/s), those estimates being in agreement with the modeled CSW propagation speed. On the inner and middle shelf, observed along-shelf subinertial currents show higher correlation coefficients with the winds located southward and earlier in time than with the local wind at the current meter mooring position and at the time of measurement. The inclusion of the remote (located southwestward) wind forcing improves the prediction of the subinertial currents when compared to the currents forced only by the local wind, since the along-shelf-modeled currents present correlation coefficients with observed along-shelf currents up to 20% higher on the inner and middle shelf when the remote wind is included. For most of the outer shelf, on the other hand, this is not observed since usually, the correlation between the currents and the synoptic winds is not statistically significant.

Evaluation of Extended Wall OSB Sheathing Connection under Combined Uplift and Shear Loading for 24-inch Heel Trusses

Science.gov (United States)

Vladimir Kochkin; Andrew DeRenzis; Xiping Wang

2014-01-01

This study was designed to evaluate the performance of the extended wall structural panel connection in resisting combined uplift and shear forces at the roof-to-wall interface with a focus on a truss heel height of 24 in. to address the expected increases in the depth of attic insulation used in Climate Zones 5 and higher. Five full-size roof-wall assemblies were...

Episodic swell growth inferred from variable uplift of the Cape Verde hotspot islands

Science.gov (United States)

Ramalho, R.; Helffrich, G.; Cosca, M.; Vance, D.; Hoffmann, D.; Schmidt, D.N.

2010-01-01

On the Beagle voyage, Charles Darwin first noted the creation and subsidence of ocean islands, establishing in geology's infancy that island freeboard changes with time. Hotspot ocean islands have an obvious mechanism for freeboard change through the growth of the bathymetric anomaly, or swell, on which the islands rest. Models for swell development indicate that flexural, thermal or dynamic pressure contributions, as well as spreading of melt residue from the hotspot, can all contribute to island uplift. Here we test various models for swell development using the uplift histories for the islands of the Cape Verde hotspot, derived from isotopic dating of marine terraces and subaerial to submarine lava-flow morphologies. The island uplift histories, in conjunction with inter-island spacing, uplift rate and timing differences, rule out flexural, thermal or dynamic pressure contributions. We also find that uplift cannot be reconciled with models that advocate the spreading of melt residue in swell development unless swell growth is episodic. Instead, we infer from the uplift histories that two processes have acted to raise the islands during the past 6 Myr. During an initial phase, mantle processes acted to build the swell. Subsequently, magmatic intrusions at the island edifice caused 350 m of local uplift at the scale of individual islands. Finally, swell-wide uplift contributed a further 100 m of surface rise.

Ratings uplifts and bank characteristics in the Eurozone 2002-2011

NARCIS (Netherlands)

Dijkstra, M.A.

2013-01-01

This paper explores which characteristics define banks that are too-big-to-fail in the Eurozone over the period 2002-2011. These banks are identified through ratings uplift data from Moody’s. Higher ratings uplifts are associated with higher degrees of interest income and lower degrees of commission

Study on the estimation method of uplift during the late Quaternary by using river terraces (3). Tectonic movement described by last 100,000 years uplift distribution in an inland area

International Nuclear Information System (INIS)

Hataya, Ryuta

2006-01-01

Uplift for the last 100,000 years, which is estimated in both side of the Ayashi fault in Miyagi prefecture and the Sekiya fault in Tochigi Prefecture by using the relative height of river terraces is almost equal to vertical displacements of these faults for the last 100,000 years. Hence, the method using fluvial terraces is available for estimating the uplift for the last 100,000 years in an inland area quantatively. Furthermore, significance of the uplift obtained by the proposed methodology in this study is emphasized. It is possible to find the geotectonic feature that were so far overlooked as deformed zones along active fault, tectonic style of uplift and subsidence by obtaining the 3-dimensional distribution of uplift in last 100,000 years. Methodology and concept proposed in this study give practical survey method of late Quaternary 3-dimensional uplift characteristics for the long-term safety of geological disposal of high-level radioactive waste. By applying this method to Quaternary research, new insights on the Quaternary tectonic movement may be given. (author)

Elastic uplift in southeast Greenland due to rapid ice mass loss

DEFF Research Database (Denmark)

Khan, Shfaqat Abbas; Van dam, Tonie; Hamilton, Gordon S.

2007-01-01

The rapid unloading of ice from the southeastern sector of the Greenland ice sheet between 2001 and 2006 caused an elastic uplift of 35 mm at a GPS site in Kulusuk. Most of the uplift results from ice dynamic-induced volume losses on two nearby outlet glaciers. Volume loss from Helheim Glacier...... between 62N and 66N. Citation: Khan, S. A., J. Wahr, L. A. Stearns, G. S. Hamilton, T. van Dam, K. M. Larson, and O. Francis (2007), Elastic uplift in southeast Greenland due to rapid ice mass loss....

Comparison of Force and Moment Coefficients for the Same Test Article in Multiple Wind Tunnels

Science.gov (United States)

Deloach, Richard

2013-01-01

This paper compares the results of force and moment measurements made on the same test article and with the same balance in three transonic wind tunnels. Comparisons are made for the same combination of Reynolds number, Mach number, sideslip angle, control surface configuration, and angle of attack range. Between-tunnel force and moment differences are quantified. An analysis of variance was performed at four unique sites in the design space to assess the statistical significance of between-tunnel variation and any interaction with angle of attack. Tunnel to tunnel differences too large to attribute to random error were detected were observed for all forces and moments. In some cases these differences were independent of angle of attack and in other cases they changed with angle of attack.

Numerical modelling study on the flexural uplift of the Transantarctic Mountains

NARCIS (Netherlands)

Yamasaki, T.; Miura, H.; Nogi, Y.

2008-01-01

In this study, based on a 2-D thermomechanical finite element model, the uplift of the Transantarctic Mountains (TAM) is discussed in relation to the flexural uplift of a rheologically layered lithosphere, which is described by Vening-Meinesz's cantilever kinematics. The general model behaviour

Weather Research and Forecasting Model Wind Sensitivity Study at Edwards Air Force Base, CA

Science.gov (United States)

Watson, Leela R.; Bauman, William H., III; Hoeth, Brian

2009-01-01

This abstract describes work that will be done by the Applied Meteorology Unit (AMU) in assessing the success of different model configurations in predicting "wind cycling" cases at Edwards Air Force Base, CA (EAFB), in which the wind speeds and directions oscillate among towers near the EAFB runway. The Weather Research and Forecasting (WRF) model allows users to choose among two dynamical cores - the Advanced Research WRF (ARW) and the Non-hydrostatic Mesoscale Model (NMM). There are also data assimilation analysis packages available for the initialization of the WRF model - the Local Analysis and Prediction System (LAPS) and the Advanced Regional Prediction System (ARPS) Data Analysis System (ADAS). Having a series of initialization options and WRF cores, as well as many options within each core, creates challenges for local forecasters, such as determining which configuration options are best to address specific forecast concerns. The goal of this project is to assess the different configurations available and determine which configuration will best predict surface wind speed and direction at EAFB.

Effect of Difference-frequency Forces on the Dynamics of a Semi-submersible Type FVAWT in Misaligned Wave-wind Condition

DEFF Research Database (Denmark)

Wang, Kai; Cheng, Zhengshun; Moan, Torgeir

2015-01-01

With increasing interests in the development of offshore floating vertical axis wind turbines (FVAWTs), a large amount of studies on the FVAWTs have been conducted. This paper focuses on evaluating the effect of second-order difference-frequency force on the dynamics of a 5 MW FVAWT in misaligned...... wave-wind condition. The studied FVAWT is composed of a 5 MW Darrieus rotor, a semi-submersible floater and a catenary mooring system. Fully coupled nonlinear time domain simulations were conducted using the state-of-art code Simo- Riflex-DMS. Several misaligned wave-wind conditions were selected...... to investigate the global dynamic responses of the FVAWT, such as the platform motions, structural responses and mooring line tensions. It has been found that the wave-wind misalignment does not significantly affect the mean values of the global responses since the global responses are primarily wind...

Wind loads on flat plate photovoltaic array fields

Science.gov (United States)

Miller, R. D.; Zimmerman, D. K.

1981-01-01

The results of an experimental analysis (boundary layer wind tunnel test) of the aerodynamic forces resulting from winds acting on flat plate photovoltaic arrays are presented. Local pressure coefficient distributions and normal force coefficients on the arrays are shown and compared to theoretical results. Parameters that were varied when determining the aerodynamic forces included tilt angle, array separation, ground clearance, protective wind barriers, and the effect of the wind velocity profile. Recommended design wind forces and pressures are presented, which envelop the test results for winds perpendicular to the array's longitudinal axis. This wind direction produces the maximum wind loads on the arrays except at the array edge where oblique winds produce larger edge pressure loads. The arrays located at the outer boundary of an array field have a protective influence on the interior arrays of the field. A significant decrease of the array wind loads were recorded in the wind tunnel test on array panels located behind a fence and/or interior to the array field compared to the arrays on the boundary and unprotected from the wind. The magnitude of this decrease was the same whether caused by a fence or upwind arrays.

Abrupt uplift within the past 1700 years at Southern Puget Sound, Washington

Science.gov (United States)

Bucknam, R.C.; Hemphill-Haley, E.; Leopold, E.B.

1992-01-01

Shorelines rose as much as 7 meters along southern Puget Sound and Hood Canal between 500 and 1700 years ago. Evidence for this uplift consists of elevated wave-cut shore platforms near Seattle and emerged, peat-covered tidal flats as much as 60 kilometers to the southwest. The uplift was too rapid for waves to leave intermediate shorelines on even the best preserved platform. The tidal flats also emerged abruptly; they changed into freshwater swamps and meadows without first becoming tidal marshes. Where uplift was greatest, it adjoined an inferred fault that crosses Puget Sound at Seattle and it probably accompanied reverse slip on that fault 1000 to 1100 years ago. The uplift and probable fault slip show that the crust of the North America plate contains potential sources of damaging earthquakes in the Puget Sound region.

Is It Safe to Uplift This Patch? An Empirical Study on Mozilla Firefox

OpenAIRE

Castelluccio, Marco; An, Le; Khomh, Foutse

2017-01-01

In rapid release development processes, patches that fix critical issues, or implement high-value features are often promoted directly from the development channel to a stabilization channel, potentially skipping one or more stabilization channels. This practice is called patch uplift. Patch uplift is risky, because patches that are rushed through the stabilization phase can end up introducing regressions in the code. This paper examines patch uplift operations at Mozilla, with the aim to ide...

Quantification of Net Erosion and Uplift Experienced by the Barmer Basin, Rajasthan Using Sonic Log

Science.gov (United States)

Mitra, K.; Schulz, S.; Sarkar, A.

2015-12-01

Barmer Basin of Rajasthan, Western India is a hydrocarbon rich sedimentary basin currently being explored by Cairn India Limited. The hydrocarbon bearing Fatehgarh Formation is being found at different depths in different oil fields (e.g. From south to north: Guda, Vijaya & Vandana, Air field High) of the basin. The net uplift and erosion in the Barmer Basin has been quantified using compaction methodology. The sonic log, which is strongly controlled by porosity, is an appropriate indicator of compaction, and hence used for quantification of net uplift and erosion from compaction. The compaction methodology has been applied to the shale rich Dharvi Dungar Formation of Barmer Basin of Late Paleocene age. The net uplift and erosion is also being checked with the help of AFTA-VR and seismic sections. The results show relatively no uplift in the southernmost part of the basin and a Guda field well is thus taken to be the reference well with respect to which the uplifts in different parts of the basin have been calculated. The northern part of the basin i.e. Air Field High wells experienced maximum uplift (~2150m). Interestingly, a few wells further south of the reference well show evidence for uplift. The study was able to point out errors in the report produced with the help of AFTA-VR which found out less uplift in Vijaya & Vandana oil fields as opposed to sonic log data. The process of finding out uplift using sonic log has a standard deviation of 200m as compared to about 500m error in AFTA-VR method. This study has major implications for hydrocarbon exploration. Maturation of source rock will be higher for any given geothermal history if net uplift and erosion is incorporated in maturation modeling. They can also be used for porosity predictions of reservoir units in undrilled targets.

Continuous uplift near the seaward edge of the Prince William Sound megathrust: Middleton Island, Alaska

Science.gov (United States)

Savage, James C.; Plafker, George; Svarc, Jerry L.; Lisowski, Michael

2014-01-01

Middleton Island, located at the seaward edge of the continental shelf 50 km from the base of the inner wall of the Aleutian Trench, affords an opportunity to make land-based measurements of uplift near the toe of the Prince William Sound megathrust, site of the 1964, M = 9.2, Alaska earthquake. Leveling surveys (1973–1993) on Middleton Island indicate roughly uniform tilting (~1 µrad/a down to the northwest) of the island, and GPS surveys (1993–2012) show an uplift rate of 14 mm/a of the island relative to fixed North America. The data are consistent with a combined (coseismic and postseismic) uplift (in meters) due to the 1964 earthquake as a function of time τ (years after the earthquake) u(τ) = (3.5 + 1.21 log10 [1 + 1.67 τ]) H(τ) where 3.5 is the coseismic uplift and H(τ) is 0 for τ < 0 and 1 otherwise. The current uplift on Middleton Island is attributed to continuous slip on a fault splaying off from the megathrust, and the long-term uplift is the superposition of the effects of past earthquakes, each earthquake being similar to the 1964 event. Then, the predicted uplift at time t due to a sequence of earthquakes at times tiwould be . From studies of strandlines associated with the uplifted terraces on Middleton Island, Plafker et al. (1992) estimated the occurrence times of the last six earthquakes and measured the present-day elevations of those strandlines. The predicted uplift is in rough agreement with those measurements. About half of the predicted uplift is due to postseismic relaxation from previous earthquakes.

Using C-Band Dual-Polarization Radar Signatures to Improve Convective Wind Forecasting at Cape Canaveral Air Force Station and NASA Kennedy Space Center

Science.gov (United States)

Amiot, Corey G.; Carey, Lawrence D.; Roeder, William P.; McNamara, Todd M.; Blakeslee, Richard J.

2017-01-01

The United States Air Force's 45th Weather Squadron (45WS) is the organization responsible for monitoring atmospheric conditions at Cape Canaveral Air Force Station and NASA Kennedy Space Center (CCAFS/KSC) and issuing warnings for hazardous weather conditions when the need arises. One such warning is issued for convective wind events, for which lead times of 30 and 60 minutes are desired for events with peak wind gusts of 35 knots or greater (i.e., Threshold-1) and 50 knots or greater (i.e., Threshold-2), respectively (Roeder et al. 2014).

Multi Canister Overpack (MCO) Handling Machine Trolley Seismic Uplift Constraint Design Loads

International Nuclear Information System (INIS)

SWENSON, C.E.

2000-01-01

The MCO Handling Machine (MHM) trolley moves along the top of the MHM bridge girders on east-west oriented rails. To prevent trolley wheel uplift during a seismic event, passive uplift constraints are provided as shown in Figure 1-1. North-south trolley wheel movement is prevented by flanges on the trolley wheels. When the MHM is positioned over a Multi-Canister Overpack (MCO) storage tube, east-west seismic restraints are activated to prevent trolley movement during MCO handling. The active seismic constraints consist of a plunger, which is inserted into slots positioned along the tracks as shown in Figure 1-1. When the MHM trolley is moving between storage tube positions, the active seismic restraints are not engaged. The MHM has been designed and analyzed in accordance with ASME NOG-1-1995. The ALSTHOM seismic analysis (Reference 3) reported seismic uplift restraint loading and EDERER performed corresponding structural calculations. The ALSTHOM and EDERER calculations were performed with the east-west seismic restraints activated and the uplift restraints experiencing only vertical loading. In support of development of the CSB Safety Analysis Report (SAR), an evaluation of the MHM seismic response was requested for the case where the east-west trolley restraints are not engaged. For this case, the associated trolley movements would result in east-west lateral loads on the uplift constraints due to friction, as shown in Figure 1-2. During preliminary evaluations, questions were raised as to whether the EDERER calculations considered the latest ALSTHOM seismic analysis loads (See NCR No. 00-SNFP-0008, Reference 5). Further evaluation led to the conclusion that the EDERER calculations used appropriate vertical loading, but the uplift restraints would need to be re-analyzed and modified to account for lateral loading. The disposition of NCR 00-SNFP-0008 will track the redesign and modification effort. The purpose of this calculation is to establish bounding seismic

Do hassles and uplifts change with age? Longitudinal findings from the VA normative aging study.

Science.gov (United States)

Aldwin, Carolyn M; Jeong, Yu-Jin; Igarashi, Heidi; Spiro, Avron

2014-03-01

To examine emotion regulation in later life, we contrasted the modified hedonic treadmill theory with developmental theories, using hassles and uplifts to assess emotion regulation in context. The sample was 1,315 men from the VA Normative Aging Study aged 53 to 85 years, who completed 3,894 observations between 1989 and 2004. We computed 3 scores for both hassles and uplifts: intensity (ratings reflecting appraisal processes), exposure (count), and summary (total) scores. Growth curves over age showed marked differences in trajectory patterns for intensity and exposure scores. Although exposure to hassles and uplifts decreased in later life, intensity scores increased. Group-based modeling showed individual differences in patterns of hassles and uplifts intensity and exposure, with relative stability in uplifts intensity, normative nonlinear changes in hassles intensity, and complex patterns of individual differences in exposure for both hassles and uplifts. Analyses with the summary scores showed that emotion regulation in later life is a function of both developmental change and contextual exposure, with different patterns emerging for hassles and uplifts. Thus, support was found for both hedonic treadmill and developmental change theories, reflecting different aspects of emotion regulation in late life. (c) 2014 APA, all rights reserved.

Wind-Tunnel Investigation of Wind Loads on a Post-Panamax Container Ship as a Function of the Container Configuration on Deck

DEFF Research Database (Denmark)

Andersen, Ingrid Marie Vincent

2012-01-01

An investigation of the wind forces acting on a 9,000+ TEU container ship has been carried out through a series of wind tunnel tests. It was investigated how the wind forces depend on the container configuration on the deck using a 1:450 scale model and a series of appropriate container...... are presented as nondimensional coefficients. It is concluded, that the measured forces and moment depend on the container configuration on deck, and the results may provide a general idea of how the magnitude of the wind forces is affected by a given container stacking configuration on a similar container ship....

Ocean Wave Simulation Based on Wind Field.

Directory of Open Access Journals (Sweden)

Zhongyi Li

Full Text Available Ocean wave simulation has a wide range of applications in movies, video games and training systems. Wind force is the main energy resource for generating ocean waves, which are the result of the interaction between wind and the ocean surface. While numerous methods to handle simulating oceans and other fluid phenomena have undergone rapid development during the past years in the field of computer graphic, few of them consider to construct ocean surface height field from the perspective of wind force driving ocean waves. We introduce wind force to the construction of the ocean surface height field through applying wind field data and wind-driven wave particles. Continual and realistic ocean waves result from the overlap of wind-driven wave particles, and a strategy was proposed to control these discrete wave particles and simulate an endless ocean surface. The results showed that the new method is capable of obtaining a realistic ocean scene under the influence of wind fields at real time rates.

Effect on non-linear soil-structure interaction due to base slab uplift on the seismic response of a high-temperature gas-cooled reactor (HTGR)

International Nuclear Information System (INIS)

Kennedy, R.P.; Short, S.A.

1976-01-01

In high seismic regions it has often been the practice to use oversized base slabs for the major nuclear power plant structures in order to prevent, or at least minimize the amount of dynamic base slab uplift which will result from the overturning moments developed during seismic ground motion. Two major reasons have been expressed as to why dynamic base slab uplift should be minimized: (1) As nuclear power plants are normally designed for seismic loadings based upon linear analysis, and since soil-structure interaction becomes nonlinear when only a portion of the base slab is in contact with the soil, linear elasticity analysis may be acceptable if base slab uplift occurs (as the resultant design loads may be incorrect), and (2) substantial uplift could cause excessive toe pressures in the supporting soil and significant impact forces when the slab recontacts the soil. The primary purpose of this paper is to evaluate the importance of the nonlinear soil-structure interaction effects resulting from substantial base slab uplift occurring during a seismic excitation. The structure for this investigation consisted of the containment building and prestressed reactor vessel (PCRV) for a typical HTGR plant. A simplified dynamic mathematical model was utilized consisting of a conventional lumped mass structure with soil-structure interaction accounted for by translational and rotational springs whose properties are determined by elastic half space theory. Three different site soil conditions (a rock site, a moderately stiff soil, and a soft soil) and two levels of horizontal ground motion (0.3 and 0.5 g earthquakes) were considered. (Auth.)

Spatial and temporal variation of tectonic uplift in the southeastern Ethiopian Plateau from morphotectonic analysis

Science.gov (United States)

Xue, Liang; Alemu, Tadesse; Gani, Nahid D.; Abdelsalam, Mohamed G.

2018-05-01

We use morphotectonic analysis to study the tectonic uplift history of the southeastern Ethiopian Plateau (SEEP). Based on studies conducted on the Northwestern Ethiopian Plateau, steady-state and pulsed tectonic uplift models were proposed to explain the growth of the plateau since 30 Ma. We test these two models for the largely unknown SEEP. We present the first quantitative morphotectonic study of the SEEP. First, in order to infer the spatial distribution of the tectonic uplift rates, we extract geomorphic proxies including normalized steepness index ksn, hypsometric integral HI, and chi integral χ from the Advanced Spaceborne Thermal Emission and Reflection Radiometer (ASTER) digital elevation model (DEM). Second, we compare these rates with the thickness of flood basalt that we estimated from geological maps. Third, to constrain the timing of regional tectonic uplift, we develop a knickpoint celerity model. Fourth, we compare our results to those from the Northwestern Ethiopian Plateau to suggest a possible mechanism to explain regional tectonic uplift of the entire Ethiopian Plateau. We find an increase in tectonic uplift rates from the southeastern escarpments of the Afar Depression in the northeast to that of the Main Ethiopian Rift to the southwest. We identify three regional tectonic uplift events at 11.7, 6.5, and 4.5 Ma recorded by the development of regionally distributed knickpoints. This is in good agreement with ages of tectonic uplift events reported from the Northwestern Ethiopian Plateau.

Greenland uplift and regional sea level changes from ICESat observations and GIA modelling

DEFF Research Database (Denmark)

Spada, G.; Ruggieri, G.; Sørensen, Louise Sandberg

2012-01-01

‐resolution GrIS mass balance, we study the time‐variations of various geophysical quantities in response to the current mass loss. They include vertical uplift and subsidence, geoid height variations, global patterns of sea level change (or fingerprints), and regional sea level variations along the coasts...... of Greenland. Long‐wavelength uplifts and gravity variations in response to current or past ice thickness variations are obtained solving the sea level equation, which accounts for both the elastic and the viscoelastic components of deformation. To capture the short‐wavelength components of vertical uplift...... in response to current ice mass loss, which is not resolved by satellite gravity observations, we have specifically developed a high‐resolution regional elastic rebound (ER) model. The elastic component of vertical uplift is combined with estimates of the viscoelastic displacement fields associated...

Spatial dependence in wind and optimal wind power allocation: A copula-based analysis

International Nuclear Information System (INIS)

Grothe, Oliver; Schnieders, Julius

2011-01-01

The investment decision on the placement of wind turbines is, neglecting legal formalities, mainly driven by the aim to maximize the expected annual energy production of single turbines. The result is a concentration of wind farms at locations with high average wind speed. While this strategy may be optimal for single investors maximizing their own return on investment, the resulting overall allocation of wind turbines may be unfavorable for energy suppliers and the economy because of large fluctuations in the overall wind power output. This paper investigates to what extent optimal allocation of wind farms in Germany can reduce these fluctuations. We analyze stochastic dependencies of wind speed for a large data set of German on- and offshore weather stations and find that these dependencies turn out to be highly nonlinear but constant over time. Using copula theory we determine the value at risk of energy production for given allocation sets of wind farms and derive optimal allocation plans. We find that the optimized allocation of wind farms may substantially stabilize the overall wind energy supply on daily as well as hourly frequency. - Highlights: → Spatial modeling of wind forces in Germany. → A novel way to assess nonlinear dependencies of wind forces by copulas. → Wind turbine allocation by maximizing lower quantiles of energy production. → Optimal results show major increase in reliable part of wind energy.

Continuous uplift near the seaward edge of the Prince William Sound megathrust: Middleton Island, Alaska

Science.gov (United States)

Savage, J. C.; Plafker, G.; Svarc, J. L.; Lisowski, M.

2014-07-01

Middleton Island, located at the seaward edge of the continental shelf 50 km from the base of the inner wall of the Aleutian Trench, affords an opportunity to make land-based measurements of uplift near the toe of the Prince William Sound megathrust, site of the 1964, M = 9.2, Alaska earthquake. Leveling surveys (1973-1993) on Middleton Island indicate roughly uniform tilting ( 1 µrad/a down to the northwest) of the island, and GPS surveys (1993-2012) show an uplift rate of 14 mm/a of the island relative to fixed North America. The data are consistent with a combined (coseismic and postseismic) uplift (in meters) due to the 1964 earthquake as a function of time τ (years after the earthquake) u(τ) = (3.5 + 1.21 log10 [1 + 1.67 τ]) H(τ) where 3.5 is the coseismic uplift and H(τ) is 0 for τ ∑iut-ti. From studies of strandlines associated with the uplifted terraces on Middleton Island, Plafker et al. (1992) estimated the occurrence times of the last six earthquakes and measured the present-day elevations of those strandlines. The predicted uplift is in rough agreement with those measurements. About half of the predicted uplift is due to postseismic relaxation from previous earthquakes.

Force Measurements on a VAWT Blade in Parked Conditions

Directory of Open Access Journals (Sweden)

Anders Goude

2017-11-01

Full Text Available The forces on a turbine at extreme wind conditions when the turbine is parked is one of the most important design cases for the survivability of a turbine. In this work, the forces on a blade and its support arms have been measured on a 12 kW straight-bladed vertical axis wind turbine at an open site. Two cases are tested: one during electrical braking of the turbine, which allows it to rotate slowly, and one with the turbine mechanically fixed with the leading edge of the blade facing the main wind direction. The force variations with respect to wind direction are investigated, and it is seen that significant variations in forces depend on the wind direction. The measurements show that for the fixed case, when subjected to the same wind speed, the forces are lower when the blade faces the wind direction. The results also show that due to the lower forces at this particular wind direction, the average forces for the fixed blade are notably lower. Hence, it is possible to reduce the forces on a turbine blade, simply by taking the dominating wind direction into account when the turbine is parked. The measurements also show that a positive torque is generated from the blade for most wind directions, which causes the turbine to rotate in the electrically-braked case. These rotations will cause increased fatigue loads on the turbine blade.

Simulated variations of eolian dust from inner Asian deserts at the mid-Pliocene, last glacial maximum, and present day: contributions from the regional tectonic uplift and global climate change

Energy Technology Data Exchange (ETDEWEB)

Shi, Zhengguo; Liu, Xiaodong; An, Zhisheng [Chinese Academy of Sciences, State Key Laboratory of Loess Quaternary Geology (SKLLQG), Institute of Earth Environment, Xi' an (China); Yi, Bingqi; Yang, Ping [Texas A and M University, College Station, TX (United States); Mahowald, Natalie [Cornell University, Ithaca, NY (United States)

2011-12-15

Northern Tibetan Plateau uplift and global climate change are regarded as two important factors responsible for a remarkable increase in dust concentration originating from inner Asian deserts during the Pliocene-Pleistocene period. Dust cycles during the mid-Pliocene, last glacial maximum (LGM), and present day are simulated with a global climate model, based on reconstructed dust source scenarios, to evaluate the relative contributions of the two factors to the increment of dust sedimentation fluxes. In the focused downwind regions of the Chinese Loess Plateau/North Pacific, the model generally produces a light eolian dust mass accumulation rate (MAR) of 7.1/0.28 g/cm{sup 2}/kyr during the mid-Pliocene, a heavier MAR of 11.6/0.87 g/cm{sup 2}/kyr at present, and the heaviest MAR of 24.5/1.15 g/cm{sup 2}/kyr during the LGM. Our results are in good agreement with marine and terrestrial observations. These MAR increases can be attributed to both regional tectonic uplift and global climate change. Comparatively, the climatic factors, including the ice sheet and sea surface temperature changes, have modulated the regional surface wind field and controlled the intensity of sedimentation flux over the Loess Plateau. The impact of the Tibetan Plateau uplift, which increased the areas of inland deserts, is more important over the North Pacific. The dust MAR has been widely used in previous studies as an indicator of inland Asian aridity; however, based on the present results, the interpretation needs to be considered with greater caution that the MAR is actually not only controlled by the source areas but the surface wind velocity. (orig.)

An Improved Car-Following Model Accounting for Impact of Strong Wind

Directory of Open Access Journals (Sweden)

Dawei Liu

2017-01-01

Full Text Available In order to investigate the effect of strong wind on dynamic characteristic of traffic flow, an improved car-following model based on the full velocity difference model is developed in this paper. Wind force is introduced as the influence factor of car-following behavior. Among three components of wind force, lift force and side force are taken into account. The linear stability analysis is carried out and the stability condition of the newly developed model is derived. Numerical analysis is made to explore the effect of strong wind on spatial-time evolution of a small perturbation. The results show that the strong wind can significantly affect the stability of traffic flow. Driving safety in strong wind is also studied by comparing the lateral force under different wind speeds with the side friction of vehicles. Finally, the fuel consumption of vehicle in strong wind condition is explored and the results show that the fuel consumption decreased with the increase of wind speed.

Cenozoic uplift and subsidence in the North Atlantic region

DEFF Research Database (Denmark)

Anell, Ingrid Anna Margareta; Thybo, Hans; Artemieva, Irina

2009-01-01

and the surrounding areas. (2) A regional increase in subsidence in the offshore marginal areas of Norway, the northern North Sea, the northern British Isles and west Greenland took place in the Eocene (ca 57-35 Ma). (3) The Oligocene and Miocene (35-5 Ma) were characterized by regional tectonic quiescence, with only...... localised uplift, probably related to changes in plate dynamics. (4) The second major phase of regional uplift that affected all marginal areas of the North Atlantic occurred in the Plio-Pleistocene (5-0 Ma). Its amplitude was enhanced by erosion-driven glacio-isostatic compensation. Despite inconclusive...

Operation and Equivalent Loads of Wind Turbines in Large Wind Farms

Science.gov (United States)

Andersen, Soren Juhl; Sorensen, Jens Norkaer; Mikkelsen, Robert Flemming

2017-11-01

Wind farms continue to grow in size and as the technology matures, the design of wind farms move towards including dynamic effects besides merely annual power production estimates. The unsteady operation of wind turbines in large wind farms has been modelled with EllipSys3D(Michelsen, 1992, and Sørensen, 1995) for a number of different scenarios using a fully coupled large eddy simulations(LES) and aero-elastic framework. The turbines are represented in the flow fields using the actuator line method(Sørensen and Shen, 2002), where the aerodynamic forces and deflections are derived from an aero-elastic code, Flex5(Øye, 1996). The simulations constitute a database of full turbine operation in terms of both production and loads for various wind speeds, turbulence intensities, and turbine spacings. The operating conditions are examined in terms of averaged power production and thrust force, as well as 10min equivalent flapwise bending, yaw, and tilt moment loads. The analyses focus on how the performance and loads change throughout a given farm as well as comparing how various input parameters affect the operation and loads of the wind turbines during different scenarios. COMWIND(Grant 2104-09- 067216/DSF), Nordic Consortium on Optimization and Control of Wind Farms, Eurotech Greentech Wind project, Winds2Loads, and CCA LES. Ressources Granted on SNIC and JESS. The Vestas NM80 turbine has been used.

GPS Imaging of vertical land motion in California and Nevada: Implications for Sierra Nevada uplift

Science.gov (United States)

Blewitt, Geoffrey; Kreemer, Corné

2016-01-01

Abstract We introduce Global Positioning System (GPS) Imaging, a new technique for robust estimation of the vertical velocity field of the Earth's surface, and apply it to the Sierra Nevada Mountain range in the western United States. Starting with vertical position time series from Global Positioning System (GPS) stations, we first estimate vertical velocities using the MIDAS robust trend estimator, which is insensitive to undocumented steps, outliers, seasonality, and heteroscedasticity. Using the Delaunay triangulation of station locations, we then apply a weighted median spatial filter to remove velocity outliers and enhance signals common to multiple stations. Finally, we interpolate the data using weighted median estimation on a grid. The resulting velocity field is temporally and spatially robust and edges in the field remain sharp. Results from data spanning 5–20 years show that the Sierra Nevada is the most rapid and extensive uplift feature in the western United States, rising up to 2 mm/yr along most of the range. The uplift is juxtaposed against domains of subsidence attributable to groundwater withdrawal in California's Central Valley. The uplift boundary is consistently stationary, although uplift is faster over the 2011–2016 period of drought. Uplift patterns are consistent with groundwater extraction and concomitant elastic bedrock uplift, plus slower background tectonic uplift. A discontinuity in the velocity field across the southeastern edge of the Sierra Nevada reveals a contrast in lithospheric strength, suggesting a relationship between late Cenozoic uplift of the southern Sierra Nevada and evolution of the southern Walker Lane. PMID:27917328

Spatial and temporal uplift history of South America from calibrated drainage analysis

Science.gov (United States)

Rodríguez Tribaldos, V.; White, N. J.; Roberts, G. G.; Hoggard, M. J.

2017-06-01

A multidisciplinary approach is used to analyze the Cenozoic uplift history of South America. Residual depth anomalies of oceanic crust abutting this continent help to determine the pattern of present-day dynamic topography. Admittance analysis and crustal thickness measurements indicate that the elastic thickness of the Borborema and Altiplano regions is ≤10 km with evidence for sub-plate support at longer wavelengths. A drainage inventory of 1827 river profiles is assembled and used to investigate landscape development. Linear inverse modeling enables river profiles to be fitted as a function of the spatial and temporal history of regional uplift. Erosional parameters are calibrated using observations from the Borborema Plateau and tested against continent-wide stratigraphic and thermochronologic constraints. Our results predict that two phases of regional uplift of the Altiplano plateau occurred in Neogene times. Regional uplift of the southern Patagonian Andes also appears to have occurred in Early Miocene times. The consistency between observed and predicted histories for the Borborema, Altiplano, and Patagonian plateaux implies that drainage networks record coherent signals that are amenable to simple modeling strategies. Finally, the predicted pattern of incision across the Amazon catchment constrains solid sedimentary flux at the Foz do Amazonas. Observed and calculated flux estimates match, suggesting that erosion and deposition were triggered by regional Andean uplift during Miocene times.

The k-ε-fP model applied to double wind turbine wakes using different actuator disk force methods

DEFF Research Database (Denmark)

Laan, van der, Paul Maarten; Sørensen, Niels N.; Réthoré, Pierre-Elouan

2015-01-01

The newly developed k-ε-fP  eddy viscosity model is applied to double wind turbine wake configurations in a neutral atmospheric boundary layer, using a Reynolds-Averaged Navier–Stokes solver. The wind turbines are represented by actuator disks. A proposed variable actuator disk force method...... two methods overpredict it. The results of the k-ε-fP  eddy viscosity model are also compared with the original k-ε eddy viscosity model and large-eddy simulations. Compared to the large-eddy simulations-predicted velocity and power deficits, the k-ε-fP  is superior to the original k-ε model...

Sedimentary tectonic evolution and reservoir-forming conditions of the Dazhou–Kaijiang paleo-uplift, Sichuan Basin

Directory of Open Access Journals (Sweden)

Yueming Yang

2016-12-01

Full Text Available Great breakthrough recently achieved in the Sinian–Lower Paleozoic gas exploration in the Leshan–Longnüsi paleo-uplift, Sichuan Basin, has also made a common view reached, i.e., large-scale paleo-uplifts will be the most potential gas exploration target in the deep strata of this basin. Apart from the above-mentioned one, the other huge paleo-uplifts are all considered to be the ones formed in the post-Caledonian period, the impact of which, however, has rarely ever been discussed on the Sinian–Lower Paleozoic oil and gas reservoir formation. In view of this, based on outcrops, drilling and geophysical data, we analyzed the Sinian–Lower Paleozoic tectonic setting and sedimentary background in the East Sichuan Basin, studied the distribution rules of reservoirs and source rocks under the control of paleo-uplifts, and finally discussed, on the basis of structural evolution analysis, the conditions for the formation of Sinian–Lower Paleozoic gas reservoirs in this study area. The following findings were achieved. (1 The Dazhou–Kaijiang inherited uplift in NE Sichuan Basin which was developed before the Middle Cambrian controlled a large area of Sinian and Cambrian beach-facies development. (2 Beach-facies reservoirs were developed in the upper part of the paleo-uplift, while in the peripheral depression belts thick source rocks were developed like the Upper Sinian Doushantuo Fm and Lower Cambrian Qiongzhusi Fm, so there is a good source–reservoir assemblage. (3 Since the Permian epoch, the Dazhou–Kaijiang paleo-uplift had gradually become elevated from the slope zone, where the Permian oil generation peak occurred in the slope or lower and gentle uplift belts, while the Triassic gas generation peak occurred in the higher uplift belts, both with a favorable condition for hydrocarbon accumulation. (4 The lower structural layers, including the Lower Cambrian and its underlying strata, in the East Sichuan Basin, are now equipped with a

Segmented Coastal Uplift Along an Erosional Subduction Margin, Northern Hikurangi Fore Arc, North Island, New Zealand

Science.gov (United States)

Marshall, J. S.; Litchfield, N. J.; Berryman, K. R.; Clark, K.; Cochran, U. A.

2013-12-01

The Hikurangi subduction margin along North Island, New Zealand accommodates oblique convergence of the Pacific plate westward beneath the Australian plate at 45 mm/yr. Along the southern margin, frontal accretion and pronounced forearc uplift occur inboard of the subducting Hikurangi plateau. In the north, subduction erosion and segmented uplift occur inboard of subducting seamounts along the plateau flank. Prior workers have established a robust foundation for coastal terrace studies along the northern Hikurangi margin (e.g., Berryman et al., 1989; Ota et al., 1992; Berryman, 1993; Wilson et al., 2006, 2007; Clark et al., 2010; Litchfield et al, 2007, 2010). New field observations presented here provide additional constraints on terrace uplift along this erosional subduction margin. Along Raukumara Peninsula (north of Poverty Bay), multiple Holocene to late Pleistocene marine and fluvial terraces occur at varying elevations, recording differential uplift across six coastal segments from Gisborne to East Cape (Ota et al., 1992; Wilson et al., 2007). In this study, two to three late Pleistocene terraces were observed on rocky headlands within the first segment (Gisborne to Whangara) at elevations of 80-185 m above msl. Preliminary correlation with OIS 5a-e sea level high stands (80-125 ka) indicates net uplift at 1.2-1.5 m/ky. Uplifted Holocene wavecut platforms occur in steps along the seaward edge of these terraces, consistent with coseismic uplift. At Makorori Point, an uplifted bench occurs along the modern seacliff at 2.3 m above the cliff base. A fossil gastropod shell from paleo-beach gravels on the platform inner edge yielded a calibrated radiocarbon age of 1680 ×110 ybp. At Turihaua Point, a ≥1 m thick deposit of Holocene beach sands overlies an uplifted wavecut platform at ≥1.5 m above mean sea level. Carbonate-cemented beachrock at the base of the sand deposit yields a calibrated radiocarbon age of 2990 ×70 ybp. At Mahia Peninsula (between Poverty

Forecasting Cool Season Daily Peak Winds at Kennedy Space Center and Cape Canaveral Air Force Station

Science.gov (United States)

Barrett, Joe, III; Short, David; Roeder, William

2008-01-01

The expected peak wind speed for the day is an important element in the daily 24-Hour and Weekly Planning Forecasts issued by the 45th Weather Squadron (45 WS) for planning operations at Kennedy Space Center (KSC) and Cape Canaveral Air Force Station (CCAFS). The morning outlook for peak speeds also begins the warning decision process for gusts ^ 35 kt, ^ 50 kt, and ^ 60 kt from the surface to 300 ft. The 45 WS forecasters have indicated that peak wind speeds are a challenging parameter to forecast during the cool season (October-April). The 45 WS requested that the Applied Meteorology Unit (AMU) develop a tool to help them forecast the speed and timing of the daily peak and average wind, from the surface to 300 ft on KSC/CCAFS during the cool season. The tool must only use data available by 1200 UTC to support the issue time of the Planning Forecasts. Based on observations from the KSC/CCAFS wind tower network, surface observations from the Shuttle Landing Facility (SLF), and CCAFS upper-air soundings from the cool season months of October 2002 to February 2007, the AMU created multiple linear regression equations to predict the timing and speed of the daily peak wind speed, as well as the background average wind speed. Several possible predictors were evaluated, including persistence, the temperature inversion depth, strength, and wind speed at the top of the inversion, wind gust factor (ratio of peak wind speed to average wind speed), synoptic weather pattern, occurrence of precipitation at the SLF, and strongest wind in the lowest 3000 ft, 4000 ft, or 5000 ft. Six synoptic patterns were identified: 1) surface high near or over FL, 2) surface high north or east of FL, 3) surface high south or west of FL, 4) surface front approaching FL, 5) surface front across central FL, and 6) surface front across south FL. The following six predictors were selected: 1) inversion depth, 2) inversion strength, 3) wind gust factor, 4) synoptic weather pattern, 5) occurrence of

Neogene Uplift and Magmatism of Anatolia: New Insights from Drainage Analysis and Basalt Geochemistry

Science.gov (United States)

McNab, F.; Ball, P.; Hoggard, M.; White, N.

2017-12-01

The origin of Anatolia's high elevation and low relief plateaux has been the subject of much recent debate. Marine sedimentary rocks distributed across Central and Eastern Anatolia require significant regional uplift in Neogene times. This uplift cannot be explained by the present-day pattern of crustal deformation which, particularly across Central and Western Anatolia, is dominanted by strike-slip and extensional faulting. Positive long wavelength free-air gravity anomalies combined with slow upper mantle seismic wave speeds suggest that the sub-lithospheric mantle provides substantial topographic support. A range of geodynamic processes have been invoked, including complex slab fragmentation and lithospheric delamination. The temporal and spatial evolution of the Anatolian landscape should be recorded by drainage networks. Indeed, major catchments contain prominent knickzones with heights of hundreds of meters and length scales of several hundred kilometers. The stream power formulation for fluvial erosion permits these knickzones to be interpreted in terms of uplift history along a river's length. Here, we jointly invert an inventory of 1,844 river profiles to determine a spatial and temporal uplift rate history. When calibrated against independent observations of uplift rate, the resultant history provides significant new constraints for the evolution of Anatolian topography. In our model, the bulk of this topography appears to grow in Neogene times. Uplift initiates in Eastern Anatolia and propagates westward at uplift rates of up to 0.5 mm/yr. Coeval with this phase of uplift, abundant basaltic magmatism has occurred throughout Anatolia. We have compiled an extensive database of published geochemical analyses. Using this database, we analyse spatial and temporal patterns of basaltic compositions to discriminate between different modes of melt generation. Two independent techniques for estimating asthenospheric potential temperatures from the compositions of

WIND TUNNEL RESEARCH ON THE INFLUENCE OF ACTIVE AIRFLOW ON THE LIFT FORCE GENERATED BY THE AIRFOIL

Directory of Open Access Journals (Sweden)

Paweł Magryta

2013-09-01

Full Text Available The paper discusses the results of wind tunnel tests of airfoils with additional active airflow applied to their upper surfaces. These studies were carried out for a range of velocities up to 28 m/s in an open wind tunnel. Several types of airfoils selected for the examination feature different geometries and are widely applied in today’s aviation industry. The changes in the lift and drag force generated by these airfoils were recorded during the study. The test bench for the tests was equipped with a compressor and a vacuum pump to enable airflow through some holes on the airfoil upper surface. A rapid prototyping method and a 3D printer based on a powder printing technique were applied to print the airfoils. All of their surfaces were subject to surface grinding to smooth their external surfaces. The wind tunnel tests with and without active airflow applied to airfoils are summarised in the paper.

Large-Scale Deformation and Uplift Associated with Serpentinization

Science.gov (United States)

Germanovich, L. N.; Lowell, R. P.; Smith, J. E.

2014-12-01

Geologic and geophysical data suggest that partially serpentinized peridotites and serpentinites are a significant part of the oceanic lithosphere. All serpentinization reactions are exothermic and result in volume expansion as high as 40%. Volume expansion beneath the seafloor will lead to surface uplift and elevated stresses in the neighborhood of the region undergoing serpentinization. The serpentinization-induced stresses are likely to result in faulting or tensile fracturing that promote the serpentinization process by creating new permeability and allowing fluid access to fresh peridotite. To explore these issues, we developed a first-order model of crustal deformation by considering an inclusion undergoing transformation strain in an elastic half-space. Using solutions for inclusions of different shapes, orientations, and depths, we calculate the surface uplift and mechanical stresses generated by the serpentinization processes. We discuss the topographic features at the TAG hydrothermal field (Mid-Atlantic Ridge, 26°N), uplift of the Miyazaki Plain (Southwestern Japan), and tectonic history of the Atlantic Massif (inside corner high of the Mid-Atlantic Ridge, 30°N, and the Atlantis Transform Fault). Our analysis suggests that an anomalous salient of 3 km in diameter and 100 m high at TAG may have resulted from approximately 20% transformational strain in a region beneath the footwall of the TAG detachment fault. This serpentinization process tends to promote slip along some overlying normal faults, which may then enhance fluid pathways to the deeper crust to continue the serpentinization process. The serpentinization also favors slip and seismicity along the antithetic faults identified below the TAG detachment fault. Our solution for the Miyazaki Plain above the Kyushu-Palau subduction zone explains the observed uplift of 120 m, but the transformational strain needs only be 3%. Transformational strains associated with serpentinization in this region may

Analyzing the Impacts of Increased Wind Power on Generation Revenue Sufficiency: Preprint

Energy Technology Data Exchange (ETDEWEB)

Wang, Qin; Wu, Hongyu; Tan, Jin; Hodge, Bri-Mathias; Li, Wanning; Luo, Cheng

2016-08-01

The Revenue Sufficiency Guarantee (RSG), as part of make-whole (or uplift) payments in electricity markets, is designed to recover the generation resources' offer-based production costs that are not otherwise covered by their market revenues. Increased penetrations of wind power will bring significant impacts to the RSG payments in the markets. However, literature related to this topic is sparse. This paper first reviews the industrial practices of implementing RSG in major U.S. independent system operators (ISOs) and regional transmission operators (RTOs) and then develops a general RSG calculation method. Finally, an 18-bus test system is adopted to demonstrate the impacts of increased wind power on RSG payments.

Aerodynamic Aspects of Wind Energy Conversion

DEFF Research Database (Denmark)

Sørensen, Jens Nørkær

2011-01-01

This article reviews the most important aerodynamic research topics in the field of wind energy. Wind turbine aerodynamics concerns the modeling and prediction of aerodynamic forces, such as performance predictions of wind farms, and the design of specific parts of wind turbines, such as rotor...

Seismic response of uplifting concrete gravity dams

International Nuclear Information System (INIS)

Leger, P.; Sauve, G.; Bhattacharjee, S.

1992-01-01

The foundation interaction effects on the seismic response of dam-foundation systems have generally been studied using the linear elastic finite element models. In reality, the foundation can not develop effective tensile stresses to a significant degree along the interface. A two-dimensional finite element model, in which nonlinear gap elements are used at the dam-foundation interface to determine the uplift response of concrete gravity dams subjected to seismic loads, is presented. Time domain analyses were performed for a wide range of modelling assumptions such as dam height, interface uplift pressure, interface mesh density, and earthquake input motions, that were systematically varied to find their influence on the seismic response. The nonlinear interface behavior generally reduces the seismic response of dam-foundation systems acting as a seismic isolation mechanism, and may increase the safety against sliding by reducing the base shear transmitted to the foundation. 4 refs., 5 figs., 6 tabs

Modeling the uplift in the Ardennes-Rhenish Massif: Mechanical weakening under the Eifel?

NARCIS (Netherlands)

Garcia-Castellanos, D.; Cloetingh, S.A.P.L.; van Balen, R.T.

2000-01-01

Middle Pleistocene uplift in the Eifel has been interpreted as the isostatic response of the lithosphere to a deep buoyant hot body. The spatial and temporal distribution of the uplift in the Ardennes-Rhenish Massif Region has recently been constrained by new data of river incision that have been

Shape and amount of the Quaternary uplift of the western Rhenish shield and the Ardennes (western Europe)

Science.gov (United States)

Demoulin, A.; Hallot, E.

2009-09-01

A good evaluation of the Quaternary uplift of the Rhenish shield is a key element for the understanding of the Cenozoic geodynamics of the western European platform in front of the alpine arc. Previous maps of the massif uplift relied on fluvial incision data since the time of the rivers' Younger Main Terrace to infer a maximum post-0.73 Ma uplift of ~ 290 m in the SE Eifel. Here, we propose a new interpretation of the incision data of the intra-massif streams, where anomalies in the terrace profiles would result from knickpoint retreat in the tributaries of the main rivers rather than from tectonic deformation. We also use additional geomorphological data referring to (1) deformed Tertiary planation surfaces, (2) the history of stream piracy that severely affected the Meuse basin in the last 1 Ma, and (3) incision data outside the Rhenish shield. A new map of the post-0.73 Ma uplift of the Rhenish shield is drawn on the basis of this enlarged dataset. It reduces the maximum amount of tectonic uplift in the SE Eifel to ~ 140 m and modifies the general shape of the uplift, namely straightening its E-W profile. It is also suggested that an uplift wave migrated across the massif, starting from its southern margin in the early Pleistocene and currently showing the highest intensity of uplift in the northern Ardennes and Eifel. These features seem to favour an uplift mechanism chiefly related to lithospheric folding and minimize the impact on the topography of a more local Eifel plume.

Harmonic Structure Predicts the Enjoyment of Uplifting Trance Music.

Science.gov (United States)

Agres, Kat; Herremans, Dorien; Bigo, Louis; Conklin, Darrell

2016-01-01

An empirical investigation of how local harmonic structures (e.g., chord progressions) contribute to the experience and enjoyment of uplifting trance (UT) music is presented. The connection between rhythmic and percussive elements and resulting trance-like states has been highlighted by musicologists, but no research, to our knowledge, has explored whether repeated harmonic elements influence affective responses in listeners of trance music. Two alternative hypotheses are discussed, the first highlighting the direct relationship between repetition/complexity and enjoyment, and the second based on the theoretical inverted-U relationship described by the Wundt curve. We investigate the connection between harmonic structure and subjective enjoyment through interdisciplinary behavioral and computational methods: First we discuss an experiment in which listeners provided enjoyment ratings for computer-generated UT anthems with varying levels of harmonic repetition and complexity. The anthems were generated using a statistical model trained on a corpus of 100 uplifting trance anthems created for this purpose, and harmonic structure was constrained by imposing particular repetition structures (semiotic patterns defining the order of chords in the sequence) on a professional UT music production template. Second, the relationship between harmonic structure and enjoyment is further explored using two computational approaches, one based on average Information Content, and another that measures average tonal tension between chords. The results of the listening experiment indicate that harmonic repetition does in fact contribute to the enjoyment of uplifting trance music. More compelling evidence was found for the second hypothesis discussed above, however some maximally repetitive structures were also preferred. Both computational models provide evidence for a Wundt-type relationship between complexity and enjoyment. By systematically manipulating the structure of chord

Geomorphic indices and relative tectonic uplift in the Guerrero sector of the Mexican forearc

Directory of Open Access Journals (Sweden)

Krzysztof Gaidzik

2017-07-01

The results of the applied landscape analysis reveal considerable variations in relief, topography and geomorphic indices values along the Guerrero sector of the Mexican subduction zone. We argue that the reported differences are indicative of tectonic deformation and of variations in relative tectonic uplift along the studied forearc. A significant drop from central and eastern parts of the study area towards the west in values of RVA (from ∼500 to ∼300, SL (from ∼500 to ca. 400, maximum SL (from ∼1500–2500 to ∼1000 and ksn (from ∼150 to ∼100 denotes a decrease in relative tectonic uplift in the same direction. We suggest that applied geomorphic indices values and forearc topography are independent of climate and lithology. Actual mechanisms responsible for the observed variations and inferred changes in relative forearc tectonic uplift call for further studies that explain the physical processes that control the forearc along strike uplift variations and that determine the rates of uplift. The proposed methodology and results obtained through this study could prove useful to scientists who study the geomorphology of forearc regions and active subduction zones.

Precise leveling determination of surface uplift patterns at the New Hydraulic Fracturing Facility, Oak Ridge National Laboratory

International Nuclear Information System (INIS)

Haase, C.S.; Stow, S.H.

1988-05-01

Surface uplift patterns were determined for five grout injections at the New Hydrofracture Facility (NHF) during the period July 1983 through January 1984. The uplift patterns are complex. In plan view, they are elliptical to almost circular and exhibit varying degrees of cross-sectional asymmetry with one side steeper than the other. The long axis of the ellipse is more or less parallel to geological strike. The uplift patterns vary in size, shape and asymmetry from injection to injection. The region of maximum uplift is typically offset with respect to the injection point, suggesting that most hydrofracture injections dip to the south-southeast. Approximately 40 to 60% of the uplift measured 5 days after an injection subsided within 30 to 45 days. In one case, all of the uplift subsided within 70 days of injection. Modeling of the uplift patterns by simple models, based on homogeneous, isotropic subsurface conditions, suggests that hydrofractures produced by the injections are either horizontal or have shallow dips to the south-southeast. Such orientations are consistent with the hydrofracture orientations determined by gamma-ray logging in observation wells surrounding the NHF site. 19 refs., 17 figs., 1 tab

The potentialities of the wind driven engines with Magnus effect

International Nuclear Information System (INIS)

Bychkov, N.M.; Gorelov, V.P.; Gorelov, S.V.; Kachanov, A.N.

1999-01-01

Possibilities of wind engine realizing of Magnus effect like of untraditional kind energy source is shown in the article. In this engine instead of traditional propellers the rotatable cylinders are installed. According interaction of the cylinders with wind the Magnus force arises. Magnus force exceeds propellers rise force in 5-10 times and maintain very large turning moment of wind wheel and most effective operation of engine, especially at low wind rates. Advantage of the engine consists in that it switch on under wind rate 1 m/c, when for propeller one requires 4-5 m/c

The Triple Spar campaign: Model tests of a 10MW floating wind turbine with waves, wind and pitch control

DEFF Research Database (Denmark)

Bredmose, Henrik; Lemmer, F.; Borg, Michael Borg

2017-01-01

Results of a test campaign for a floating wind turbine in simultaneous wind and wave forcing at scale 1:60 are presented. The floater is the Triple Spar floater, a hybrid between a spar buoy and a semi submersible tri-floater, tested here for the first time. The turbine is a model scale version...... of the DTU 10 MW reference wind turbine, which, also for the first time, is tested with active blade pitch control. The tests focus on the effects of aerodynamic damping and interaction effects between the wind forcing, wave forcing and the blade pitch control algorithm. Special focus is devoted...... to the instability of the platform pitch natural mode, that can occur if a standard land-based controller is applied....

The flux-scaling scenario. De Sitter uplift and axion inflation

International Nuclear Information System (INIS)

Blumenhagen, Ralph; Damian, Cesar; Herschmann, Daniela; Sun, Rui; Font, Anamaria

2016-01-01

Non-geometric flux-scaling vacua provide promising starting points to realize axion monodromy inflation via the F-term scalar potential. We show that these vacua can be uplifted to Minkowski and de Sitter by adding an D3-brane or a D-term containing geometric and non-geometric fluxes. These uplifted non-supersymmetric models are analyzed with respect to their potential to realize axion monodromy inflation self-consistently. Admitting rational values of the fluxes, we construct examples with the required hierarchy of mass scales. (copyright 2016 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

The flux-scaling scenario. De Sitter uplift and axion inflation

Energy Technology Data Exchange (ETDEWEB)

Blumenhagen, Ralph; Damian, Cesar; Herschmann, Daniela; Sun, Rui [Max-Planck-Institut fuer Physik (Werner-Heisenberg-Institut), Muenchen (Germany); Font, Anamaria [Departamento de Fisica, Centro de Fisica Teorica y Computacional, Facultad de Ciencias, Universidad Central de Venezuela, Caracas (Venezuela, Bolivarian Republic of)

2016-06-15

Non-geometric flux-scaling vacua provide promising starting points to realize axion monodromy inflation via the F-term scalar potential. We show that these vacua can be uplifted to Minkowski and de Sitter by adding an D3-brane or a D-term containing geometric and non-geometric fluxes. These uplifted non-supersymmetric models are analyzed with respect to their potential to realize axion monodromy inflation self-consistently. Admitting rational values of the fluxes, we construct examples with the required hierarchy of mass scales. (copyright 2016 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Study of wind forces on low-rise hip-roof building

African Journals Online (AJOL)

DR OKE

cost approach for evaluation of wind effects in comparison to wind-tunnel experiments, using the ... edges of the hip-roof building in their wind-tunnel experiments. ..... choice of turbulence model depends on considerations such as the physics ...

LiDAR Mapping of Earthquake Uplifted Paleo-shorelines, Southern Wairarapa Coast, North Island, New Zealand

Science.gov (United States)

Valenciano, J.; Angenent, J.; Marshall, J. S.; Clark, K.; Litchfield, N. J.

2017-12-01

The Hikurangi subduction margin along the east coast of the North Island, New Zealand accommodates oblique convergence of the Pacific Plate westward beneath the Australian plate at 45 mm/yr. Pronounced forearc uplift occurs at the southern end of the margin along the Wairarapa coast, onshore of the subducting Hikurangi plateau. Along a narrow coastal lowland, a series of uplifted Holocene marine terraces and beach ridges preserve a geologic record of prehistoric coseismic uplift events. In January 2017, we participated in the Research Experience for Undergraduates (REU) program of the NSF SHIRE Project (Subduction at Hikurangi Integrated Research Experiment). We visited multiple coastal sites for reconnaissance fieldwork to select locations for future in-depth study. For the coastline between Flat Point and Te Kaukau Point, we used airborne LiDAR data provided by Land Information New Zealand (LINZ) to create ArcGIS digital terrain models for mapping and correlating uplifted paleo-shorelines. Terrace elevations derived from the LiDAR data were calibrated through the use of Real Time Kinematic (RTK) GPS surveying at one field site (Glenburn Station). Prior field mapping and radiocarbon dating results (Berryman et al., 2001; Litchfield and Clark, 2015) were used to guide our LiDAR mapping efforts. The resultant maps show between four and seven uplifted terraces and associated beach ridges along this coastal segment. At some sites, terrace mapping and lateral correlation are impeded by discontinuous exposures and the presence of landslide debris, alluvial fan deposits, and sand dunes. Tectonic uplift along the southern Hikurangi margin is generated by a complex interaction between deep megathrust slip and shallow upper-plate faulting. Each uplifted Holocene paleo-shoreline is interpreted to represent a single coseismic uplift event. Continued mapping, surveying, and age dating may help differentiate between very large margin-wide megathrust earthquakes (M8.0-9.0+) and

Evaluation of Multi Canister Overpack (MCO) Handling Machine Uplift Restraint for a Seismic Event During Repositioning Operations

International Nuclear Information System (INIS)

SWENSON, C.E.

2000-01-01

Insertion of the Multi-Canister Overpack (MCO) assemblies into the Canister Storage Building (CSB) storage tubes involves the use of the MCO Handling Machine (MHM). During MCO storage tube insertion operations, inadvertent movement of the MHM is prevented by engaging seismic restraints (''active restraints'') located adjacent to both the bridge and trolley wheels. During MHM repositioning operations, the active restraints are not engaged. When the active seismic restraints are not engaged, the only functioning seismic restraints are non-engageable (''passive'') wheel uplift restraints which function only if the wheel uplift is sufficient to close the nominal 0.5-inch gap at the uplift restraint interface. The MHM was designed and analyzed in accordance with ASME NOG-1-1995. The ALSTHOM seismic analysis reported seismic loads on the MHM uplift restraints and EDERER performed corresponding structural calculations to demonstrate structural adequacy of the seismic uplift restraint hardware. The ALSTHOM and EDERER calculations were performed for a parked MHM with the active seismic restraints engaged, resulting in uplift restraint loading only in the vertical direction. In support of development of the CSB Safety Analysis Report (SAR), an evaluation of the MHM seismic response was requested for the case where the active seismic restraints are not engaged. If a seismic event occurs during MHM repositioning operations, a moving contact at a seismic uplift restraint would introduce a friction load on the restraint in the direction of the movement. These potential horizontal friction loads on the uplift restraints were not included in the existing restraint hardware design calculations. One of the purposes of the current evaluation is to address the structural adequacy of the MHM seismic uplift restraints with the addition of the horizontal friction associated with MHM repositioning movements

United States Air Force Academy (USAFA) Vertical Axis Wind Turbine.

Science.gov (United States)

1980-09-01

Rotors, SAND76-0131. Albuquerque: July 1977. 10. Oliver, R.C. and P.R. Nixon. "Design Procedure for Coupling Savonius and Darrieus Wind Turbines ", Air...May 17-20, 1976. -65- 16. Blackwell, B.F., R.E. Sheldahl, and L.V. Feltz. Wind Tunnel Performance Data for the Darrieus Wind Turbine with NACA 0012...a 5.8 m/s (13 mph) wind . At 100 rpm, the Darrieus turbine would be fully self-sustaining and acceleration would continue to an operating tip speed

SCANLIPS - A Study of Epirogenic Uplift of Scandinavia

Science.gov (United States)

England, R. W.; Ebbing, J.

2007-12-01

Thermochronology data and geomorphological interpretation indicate that parts of the Scandinavian mountains have risen by over 1 km since the Miocene. This permanent uplift, the cause of which is still disputed, varies across Norway, being greatest in southern and northern areas and least in the central region. To investigate this the SCANLIPS project employs passive seismology, coupled with modelling of potential field data to determine variations in crustal properties and structure across Norway and Sweden. Initially we intend to test whether lateral variations in crustal structure and properties are correlated with the uplift pattern. This would suggest that the cause of the differential uplift lies in a modification of the crust. If the test of this hypothesis is null we will use the data to investigate the present day upper mantle structure for the cause. Between April and October 2006 28 seismometers were deployed at sites along a c. 600 km long profile between Trondheim in Norway and Harnosand in Sweden to record teleseismic arrivals. Receiver Functions have been calculated for teleseismic events recorded at these stations and then modelled to determine crustal velocity structure, estimate Vp/Vs and depth to Moho. Preliminary results suggest that crustal thickness increases eastward beneath Norway and then remains deep beneath the lower topography of central Sweden. Along the profile a gradual eastward increase in seismic velocity, including a very high velocity lower crust beneath Sweden explains the compensation of shallow topography by thick crust. Forward density and isostatic modelling shows that the introduction of the high-density lower crust adjusts both the gravity field and the isostatic compensation. Beneath Norway the crust thins rapidly toward the continental margin at a rate that is faster than the topography decreases. This suggests that at least part of the topography is supported by the flexural strength of the crust in the footwall of the

Simulation study of solar wind push on a charged wire: basis of solar wind electric sail propulsion

Directory of Open Access Journals (Sweden)

P. Janhunen

2007-03-01

Full Text Available One possibility for propellantless propulsion in space is to use the momentum flux of the solar wind. A way to set up a solar wind sail is to have a set of thin long wires which are kept at high positive potential by an onboard electron gun so that the wires repel and deflect incident solar wind protons. The efficiency of this so-called electric sail depends on how large force a given solar wind exerts on a wire segment and how large electron current the wire segment draws from the solar wind plasma when kept at a given potential. We use 1-D and 2-D electrostatic plasma simulations to calculate the force and present a semitheoretical formula which captures the simulation results. We find that under average solar wind conditions at 1 AU the force per unit length is (5±1×10−8 N/m for 15 kV potential and that the electron current is accurately given by the well-known orbital motion limited (OML theory cylindrical Langmuir probe formula. Although the force may appear small, an analysis shows that because of the very low weight of a thin wire per unit length, quite high final speeds (over 50 km/s could be achieved by an electric sailing spacecraft using today's flight-proved components. It is possible that artificial electron heating of the plasma in the interaction region could increase the propulsive effect even further.

Variable uplift rate through time: Holocene coral reef and neotectonics of Lutao, eastern Taiwan

Science.gov (United States)

Shen, Chuan-Chou; Wu, Chung-Che; Dai, Chang-Feng; Gong, Shou-Yeh

2018-05-01

Significant discrepancies have existed regarding rate and timing of the uplift of Lutao (Green Island), located at the border of the ongoing collision between the Eurasia continental plate and the Philippine Sea Plate. To document its neotectonic history, two cores were drilled into Holocene coral reefs exposed at the southeastern coast of Lutao. Twelve pristine fossil corals, nine taken from cores and three on the surface, were 230Th dated. The results show that the coral reefs started to develop at 8,736 ± 56 yr BP (before 1950 CE) with uplift rate varying from 3.6 mm/yr during 8.7-6.0 kyr BP to 1.2 mm/yr in the past six thousand years. Our study strongly suggests that the uplift rate can vary significantly on millennial time scale. Caution should be used when extrapolating uplift rate estimates based on Mid-late Holocene corals to early times for tectonic active locations, such as Lutao.

D-term uplifted racetrack inflation

Energy Technology Data Exchange (ETDEWEB)

Brax, P. [Unite de Recherche associee au CNRS, Gif sur Yvette (France). Service de Physique Theorique, CEA/DSM/SPhT; Davis, A.C. [Cambridge Univ. (United Kingdom). DAMTP, Centre for Mathematical Sciences; Davis, S.C. [Paris-11 Univ., 91 - Orsay (France). Lab. de Physique Theorique et Hautes Energies; Jeannerot, R. [Instituut-Lorentz for Theoretical Physics, Leiden (Netherlands); Postma, M. [Deutsches Elektronen-Synchrotron (DESY), Hamburg (Germany)]|[Nationaal Inst. voor Kernfysica en Hoge-Energiefysica (NIKHEF), Amsterdam (Netherlands)

2007-10-15

It is shown that racetrack inflation can be implemented in a moduli stabilisation scenario with a supersymmetric uplifting D-term. The resulting model is completely described by an effective supergravity theory, in contrast to the original racetrack models. We study the inflationary dynamics and show that the gaugino condensates vary during inflation. The resulting spectral index is n{sub s} {approx}0.95 as in the original racetrack inflation model. Hence extra fields do not appear to alter the predictions of the model. An equivalent, simplified model with just a single field is presented. (orig.)

Effects of Mountain Uplift and Climatic Oscillations on Phylogeography and Species Divergence in Four Endangered Notopterygium Herbs

Directory of Open Access Journals (Sweden)

Khurram Shahzad

2017-11-01

Full Text Available Mountain uplift and climatic fluctuations are important driving forces that have affected the geographic distribution and population dynamics history of organisms. However, it is unclear how geological and climatic events might have affected the phylogeographic history and species divergence in high-alpine herbal plants. In this study, we analyzed the population demographic history and species differentiation of four endangered Notopterygium herbs on the high-altitude Qinghai–Tibetan Plateau (QTP and adjacent areas. We combined phylogeographic analysis with species distribution modeling to detect the genetic variations in four Notopterygium species (N. incisum, N. franchetii, N. oviforme, and N. forrestii. In total, 559 individuals from 74 populations of the four species were analyzed based on three maternally inherited chloroplast fragments (matK, rbcL, and trnS-trnG and one nuclear DNA region (internal transcribed spacer, ITS. Fifty-five chloroplast DNA (cpDNA and 48 ITS haplotypes were identified in the four species. All of the cpDNA and ITS haplotypes were species-specific, except N. franchetii and N. oviforme shared one cpDNA haplotype, H32. Phylogenetic analysis suggested that all four species formed a monophyletic clade with high bootstrap support, where N. franchetii and N. oviforme were sisters. In addition, each Notopterygium species generated an individual clade that corresponded to their respective species in the ITS tree. Population dynamics analyses and species distribution modeling showed that the two widely distributed herbs N. incisum and N. franchetii exhibited obvious demographic expansions during the Pleistocene ice ages. Molecular dating suggested that the divergence of the four Notopterygium species occurred approximately between 3.6 and 1.2 Mya, and it was significantly associated with recent extensive uplifts of the QTP. Our results support the hypothesis that mountain uplift and Quaternary climatic oscillations

Predicting Migratory Corridors of White Storks, Ciconia ciconia, to Enhance Sustainable Wind Energy Planning: A Data-Driven Agent-Based Model

Directory of Open Access Journals (Sweden)

Francis Oloo

2018-05-01

Full Text Available White storks (Ciconia ciconia are birds that make annual long-distance migration flights from their breeding grounds in the Northern Hemisphere to the south of Africa. These trips take place in the winter season, when the temperatures in the North fall and food supply drops. White storks, because of their large size, depend on the wind, thermals, and orographic characteristics of the environment in order to minimize their energy expenditure during flight. In particular, the birds adopt a soaring behavior in landscapes where the thermal uplift and orographic updrafts are conducive. By attaining suitable soaring heights, the birds then use the wind characteristics to glide for hundreds of kilometers. It is therefore expected that white storks would prefer landscapes that are characterized by suitable wind and thermal characteristics, which promote the soaring and gliding behaviors. However, these same landscapes are also potential sites for large-scale wind energy generation. In this study, we used the observed data of the white stork movement trajectories to specify a data-driven agent-based model, which simulates flight behavior of the white storks in a dynamic environment. The data on the wind characteristics and thermal uplift are dynamically changed on a daily basis so as to mimic the scenarios that the observed birds experienced during flight. The flight corridors that emerge from the simulated flights are then combined with the predicted surface on the wind energy potential, in order to highlight the potential risk of collision between the migratory white storks and hypothetical wind farms in the locations that are suitable for wind energy developments. This work provides methods that can be adopted to assess the overlap between wind energy potential and migratory corridors of the migration of birds. This can contribute to achieving sustainable trade-offs between wind energy development and conservation of wildlife and, hence, handling the

Surface Uplift Rate Constrained by Multiple Terrestrial Cosmogenic Nuclides: Theory and Application from the Central Andean Plateau

Science.gov (United States)

McPhillips, D. F.; Hoke, G. D.; Niedermann, S.; Wittmann, H.

2015-12-01

There is widespread interest in quantifying the growth and decay of topography. However, prominent methods for quantitative determinations of paleoelevation rely on assumptions that are often difficult to test. For example, stable isotope paleoaltimetry relies on the knowledge of past lapse rates and moisture sources. Here, we demonstrate how cosmogenic 10Be - 21Ne and/or 10Be - 26Al sample pairs can be applied to provide independent estimates of surface uplift rate using both published data and new data from the Atacama Desert. Our approach requires a priori knowledge of the maximum age of exposure of the sampled surface. Ignimbrite surfaces provide practical sampling targets. When erosion is very slow (roughly, ≤1 m/Ma), it is often possible to constrain paleo surface uplift rate with precision comparable to that of stable isotopic methods (approximately ±50%). The likelihood of a successful measurement is increased by taking n samples from a landscape surface and solving for one regional paleo surface uplift rate and n local erosion rates. In northern Chile, we solve for surface uplift and erosion rates using three sample groups from the literature (Kober et al., 2007). In the two lower elevation groups, we calculate surface uplift rates of 110 (+60/-12) m/Myr and 160 (+120/-6) m/Myr and estimate uncertainties with a bootstrap approach. The rates agree with independent estimates derived from stream profile analyses nearby (Hoke et al., 2007). Our calculated uplift rates correspond to total uplift of 1200 and 850 m, respectively, when integrated over appropriate timescales. Erosion rates were too high to reliably calculate the uplift rate in the third, high elevation group. New cosmogenic nuclide analyses from the Atacama Desert are in progress, and preliminary results are encouraging. In particular, a replicate sample in the vicinity of the first Kober et al. (2007) group independently yields a surface uplift rate of 110 m/Myr. Compared to stable isotope

General Forced Oscillations in a Real Power Grid Integrated with Large Scale Wind Power

Directory of Open Access Journals (Sweden)

Ping Ju

2016-07-01

Full Text Available According to the monitoring of the wide area measurement system, inter-area oscillations happen more and more frequently in a real power grid of China, which are close to the forced oscillation. Applying the conventional forced oscillation theory, the mechanism of these oscillations cannot be explained well, because the oscillations vary with random amplitude and a narrow frequency band. To explain the mechanism of such oscillations, the general forced oscillation (GFO mechanism is taken into consideration. The GFO is the power system oscillation excited by the random excitations, such as power fluctuations from renewable power generation. Firstly, properties of the oscillations observed in the real power grid are analyzed. Using the GFO mechanism, the observed oscillations seem to be the GFO caused by some random excitation. Then the variation of the wind power measured in this power gird is found to be the random excitation which may cause the GFO phenomenon. Finally, simulations are carried out and the power spectral density of the simulated oscillation is compared to that of the observed oscillation, and they are similar with each other. The observed oscillation is thus explained well using the GFO mechanism and the GFO phenomenon has now been observed for the first time in real power grids.

Role of erosion and isostasy in the Cordillera Blanca uplift: Insights from landscape evolution modeling (northern Peru, Andes)

Science.gov (United States)

Margirier, Audrey; Braun, Jean; Robert, Xavier; Audin, Laurence

2018-03-01

The processes driving uplift and exhumation of the highest Peruvian peaks (the Cordillera Blanca) are not well understood. Uplift and exhumation seem closely linked to the formation and movement on the Cordillera Blanca normal fault (CBNF) that delimits and shapes the western flank of the Cordillera Blanca. Several models have been proposed to explain the presence of this major normal fault in a compressional setting, but the CBNF and the Cordillera Blanca recent rapid uplift remain enigmatic. Whereas the Cordillera Blanca morphology demonstrates important erosion and thus a significant mass of rocks removal, the impact of erosion and isostasy on the evolution of the Cordillera Blanca uplift rates has never been explored. We address the role of erosion and associated flexural rebound in the uplift and exhumation of the Cordillera Blanca with numerical modeling of landscape evolution. We perform inversions of the broad features of the present-day topography, total exhumation and thermochronological data using a landscape evolution model (FastScape) to provide constraints on the erosion efficiency factor, the uplift rate and the temperature gradient. Our results evidence the not negligible contribution of erosion and associated flexural rebound to the uplift of the Cordillera Blanca and allow us to question the models previously proposed for the formation of the CBNF.

Tiotropium as a first maintenance drug in COPD: secondary analysis of the UPLIFT trial

DEFF Research Database (Denmark)

Troosters, T; Celli, B; Lystig, T

2010-01-01

The aim of the present study was investigate the long-term effect of tiotropium as first maintenance respiratory medication in chronic obstructive pulmonary disease (COPD). A 4-yr, randomised, multicentre, double-blind, parallel-group, placebo-controlled trial (Understanding Potential Long......-term Impacts on Function with Tiotropium (UPLIFT) was conducted. Analysis focused on the effect of tiotropium versus matching placebo in the 810 (13.5%) COPD patients not on other maintenance treatment (long-acting beta-agonists, inhaled corticosteroids, theophyllines or anticholinergics) at randomisation....... Spirometry, health-related quality of life (St George's Respiratory Questionnaire (SGRQ) score), exacerbations of COPD and mortality were also analysed. 403 patients (mean+/-sd age 63+/-8 yrs, post-bronchodilator forced expiratory volume in 1 s (FEV(1)) 53+/-12% predicted) received tiotropium and 407 (64...

Simulation study of solar wind push on a charged wire: basis of solar wind electric sail propulsion

Directory of Open Access Journals (Sweden)

P. Janhunen

2007-03-01

Full Text Available One possibility for propellantless propulsion in space is to use the momentum flux of the solar wind. A way to set up a solar wind sail is to have a set of thin long wires which are kept at high positive potential by an onboard electron gun so that the wires repel and deflect incident solar wind protons. The efficiency of this so-called electric sail depends on how large force a given solar wind exerts on a wire segment and how large electron current the wire segment draws from the solar wind plasma when kept at a given potential. We use 1-D and 2-D electrostatic plasma simulations to calculate the force and present a semitheoretical formula which captures the simulation results. We find that under average solar wind conditions at 1 AU the force per unit length is (5±1×10⁻⁸ N/m for 15 kV potential and that the electron current is accurately given by the well-known orbital motion limited (OML theory cylindrical Langmuir probe formula. Although the force may appear small, an analysis shows that because of the very low weight of a thin wire per unit length, quite high final speeds (over 50 km/s could be achieved by an electric sailing spacecraft using today's flight-proved components. It is possible that artificial electron heating of the plasma in the interaction region could increase the propulsive effect even further.

WIND TURBINE OPERATION PARAMETER CHARACTERISTICS AT A GIVEN WIND SPEED

Directory of Open Access Journals (Sweden)

Zdzisław Kamiński

2014-06-01

Full Text Available This paper discusses the results of the CFD simulation of the flow around Vertical Axis Wind Turbine rotor. The examined rotor was designed following patent application no. 402214. The turbine operation is characterised by parameters, such as opening angle of blades, power, torque, rotational velocity at a given wind velocity. Those parameters have an impact on the performance of entire assembly. The distribution of forces acting on the working surfaces in the turbine can change, depending on the angle of rotor rotation. Moreover, the resultant force derived from the force acting on the oncoming and leaving blades should be as high as possible. Accordingly, those parameters were individually simulated over time for each blade in three complete rotations. The attempts to improve the performance of the entire system resulted in a new research trend to improve the performance of working turbine rotor blades.

Permanent magnet machines with air gap windings and integrated teeth windings

Energy Technology Data Exchange (ETDEWEB)

Alatalo, M [Chalmers Univ. of Technology, Goeteborg (Sweden). School of Electrical and Computer Engineering

1996-06-01

The Thesis deals with axial and radial flux permanent magnet machines with air gap windings and an integrated teeth winding. The aim is to develop a machine that produces a high torque per unit volume with as low losses as possible. The hypothesis is that an advanced three-phase winding, magnetized by a permanent magnet rotor should be better than other machine topologies. The finite element method is used to find favourable dimensions of the slotless winding, the integrated teeth winding and the permanent magnet rotor. Three machines were built and tested in order to verify calculations. It can be concluded that the analysis method shows good agreement with the calculated and the measured values of induced voltage and torque. The experiments showed that the slotless machine with NdFeB-magnets performs approximately like the slotted machine. A theoretical comparison of axial flux topology to radial flux topology showed that the torque production of the inner rotor radial flux machine is superior to that of the axial flux machine. An integrated teeth winding based on iron powder teeth glued to the winding was studied. The force density of a pole with integrated teeth is around three times the force density of a slotless pole. A direct drive wind power generator of 6.4 kW with integrated teeth can have the same power losses and magnet weight as a transversal flux machine. Compared to a standard induction machine the integrated teeth machine had approximately 2.5 times the power capacity of the induction machine with the same power losses and outer volume. 39 refs

The Quaternary uplift history of central southern England: evidence from the terraces of the Solent River system and nearby raised beaches

Science.gov (United States)

Westaway, Rob; Bridgland, David; White, Mark

2006-09-01

We have used fluvial (Solent River system) and marine terraces to reconstruct the uplift history of central southern England. In the case of the former, we make the assumption that fluvial incision has been a direct response to surface uplift, with its precise timing controlled by climatic forcing of fluvial activity, such that height of terrace gravel above modern river is a consequence of uplift since deposition. In the case of the marine sequence, we take the height of interglacial raised beaches above a calculated contemporaneous sea-level as a measure of uplift, the calculation involving an adjustment from modern sea-level using the deep oceanic oxygen isotope signal as an indication of global ice volume at the time of deposition. This exercise requires some degree of dating constraint, which is problematic for both environments. The Solent terraces have yielded little biostratigraphical evidence, whereas the south coast raised beaches have either been poorly exposed in recent years or their ages have been controversial because of disputes between biostratigraphy and geochronological data. We have supplemented the evidence available from these sources by using key aspects of the archaeological record as dating constraints, in particular the first appearances of Levallois technique (a marker for MIS 9-8) and of bout coupé handaxes (MIS 3). The first of these has been particularly useful in modelling of the Middle Pleistocene parts of the river terrace staircases of the Solent system. In undertaking this reappraisal, we have noted several inconsistencies and disagreements between past correlation schemes for the terraces of the Solent and its various tributaries. We find that versions involving shallower downstream gradients in the main Solent River are most likely to be correct and that revisions on this basis solve a number of problems in interpretation encountered previously. Our results show that most of this region has uplifted by ˜70 m since the late

Centrifuge Testing and Seismic Response Analysis for Uplift Behavior of Spread Foundation Structures on Rock

Directory of Open Access Journals (Sweden)

Takuya Suzuki

2016-09-01

Full Text Available The uplift behavior of structures subjected to severe seismic motion has not been clarified. This paper presents experimental and analytical studies conducted for clarifying this problem of spread foundation structures on rock. First, centrifugal loading tests are conducted to determine the uplift behavior of these structures, and the uplift behavior of these structures is confirmed. Then, simulation analyses are performed using a three-dimensional FE model and the accuracy of these analyses is confirmed. A comparison between test and analyses results clarified the important analytical conditions required for maintaining analysis precision and the limit of analysis precision.

Effects of perceived stress and uplifts on inflammation and coagulability.

Science.gov (United States)

Jain, Shamini; Mills, Paul J; von Känel, Roland; Hong, Suzi; Dimsdale, Joel E

2007-01-01

We investigated whether depressed mood and chronic hassles and uplifts predicted levels of hemostasis markers D-Dimer and type-1 plasminogen activator inhibitor (PAI-1), as well as the proinflammatory markers interleukin-6 (IL-6) and soluble intercellular adhesion molecule-1 (sICAM-1) in 108 healthy individuals. One hundred eight African-American and Euro-American men and women were studied (58 men, 50 women; mean age = 36.5 +/- 8 years). D-Dimer, PAI-1, IL-6, and sICAM-1 plasma levels were analyzed from fasting venous blood samples. Data were analyzed via hierarchical linear regression and followed with partial correlation analysis. Regression analyses combined with partial correlation analyses suggested that increases in hassle frequency predicted elevated levels of sICAM-1 (p= .034), and increases in hassle severity predicted elevated levels of D-Dimer (p= .017). Increases in uplift intensity predicted lower levels of PAI-1 (p= .004) as well as showed a trend for decreased IL-6 (p= .069). Depressed mood did not significantly predict any dependent variable. These results were independent of sociodemographic, biological, and other related mood variables. The findings suggest that for even relatively healthy persons, increased perceptions of hassles are independently associated with greater inflammation and hypercoagulability, whereas increased perceptions of uplifts are independently associated with decreased hypercoagulability.

Litho-structural and geophysics features of the Alto Paranaiba Uplift

International Nuclear Information System (INIS)

Hasui, Y.

1991-01-01

The Alto Paranaiba Uplift (APU) is an almost elliptical tectonic feature of the Western Minas Gerais/Southern Goias region, which was active mostly during the Cretaceous. It separated the Parana Basin, during the formation of the Sao Bento, Uberaba and Bauru sequences, from the Alto-Sanfranciscana Basin, at the time of formation of the Areado, Patos, Capacete and Urucuia sequences. The Bouguer anomaly data indicate that the APU developed at the southwestern border of the ancient Brasilia crustal block and is represented by an almost elliptical gravity high of 15 mgal, locally disturbed by positive and negative the presence of important lineaments of a NW-SE set, mostly crossing the southwestern half of the APU. The APU development, the magmatism and the lateral basin formation involved reactivation of preexisting discontinuities and are related to a mantle plume. The tectonic development was aborted at the uplift stage during Cretaceous, after the deposition of the Bauru and Urucuia sequences, as is indicated by the Pratinha peneplane, now elevated at about 1.100 m altitude, which sculpture ended at the beginning of the Tertiary. The APU is one tectonic feature like other similar anomalies also aborted in the uplift stage or in the rift stage, which developed in Southern Brazil during the time of Atlantic Ocean opening. (author)

Short time-scale wind forced variability in the Río de la Plata Estuary and its role on ichthyoplankton retention

Science.gov (United States)

Simionato, C. G.; Berasategui, A.; Meccia, V. L.; Acha, M.; Mianzan, H.

2008-01-01

The Río de la Plata Estuary presents a strong bottom salinity front located over a submerged shoal. Apparently favored by retention processes, it is a spawning ground for several coastal fishes. This estuary is very shallow and essentially wind driven and, moreover, in time scales relevant to biota, estuarine circulation is wind dominated and highly variable. Two intriguing questions are, therefore, how this system can favor retention and what the involved mechanisms are. This paper qualitatively explores mechanisms involved in the estuary where retention is favored applying numerical simulations in which neutral particles - simulating fish eggs and early larvae - are released along the bottom frontal zone and tracked for different wind conditions. Results suggest that retentive features can be a consequence of estuarine response to natural wind variability acting over bathymetric features. For winds from most directions, particles either remain trapped near their launching position or move northeastward to southwestward along the shoal. As alternation of winds that favor along-shoal motion is the dominant feature of wind variability in the region, a retentive scenario results from prevailing wind variability. Additionally, winds that tend to export particles with a poor chance of being restored to the front are neither frequent nor persistent. Results show, therefore, that physical forcing alone might generate a retentive scenario at the inner part of this estuary. The physical retention mechanism is more effective for bottom than for surface launched particles. Wind statistics indicate that the proposed mechanism has different implications for retention along the seasons. Spring is the most favorable season, followed by summer, when particles would have a larger propensity to reach the southern area of the estuary (Samborombón Bay). Fall and winter are increasingly less favorable. All these features are consistent with patterns observed in the region in

A Methodology to Detect and Characterize Uplift Phenomena in Urban Areas Using Sentinel-1 Data

Directory of Open Access Journals (Sweden)

Roberta Bonì

2018-04-01

Full Text Available This paper presents a methodology to exploit the Persistent Scatterer Interferometry (PSI time series acquired by Sentinel-1 sensors for the detection and characterization of uplift phenomena in urban areas. The methodology has been applied to the Tower Hamlets Council area of London (United Kingdom using Sentinel-1 data covering the period 2015–2017. The test area is a representative high-urbanized site affected by geohazards due to natural processes such as compaction of recent deposits, and also anthropogenic causes due to groundwater management and engineering works. The methodology has allowed the detection and characterization of a 5 km2 area recording average uplift rates of 7 mm/year and a maximum rate of 18 mm/year in the period May 2015–March 2017. Furthermore, the analysis of the Sentinel-1 time series highlights that starting from August 2016 uplift rates began to decrease. A comparison between the uplift rates and urban developments as well as geological, geotechnical, and hydrogeological factors suggests that the ground displacements occur in a particular geological context and are mainly attributed to the swelling of clayey soils. The detected uplift could be attributed to a transient effect of the groundwater rebound after completion of dewatering works for the recent underground constructions.

Mitigation of Power System Oscillation Caused by Wind Power Fluctuation

DEFF Research Database (Denmark)

Su, Chi; Hu, Weihao; Chen, Zhe

2013-01-01

oscillation mitigation controllers are proposed and compared. A model of direct-drive-full-convertor-based wind farm connected to the IEEE 10-machine 39-bus system is adopted as the test system. The calculations and simulations are conducted in DIgSILENT PowerFactory 14.0. Results are presented to show......Wind power is increasingly integrated in modern power grids, which brings new challenges to the power system operation. Wind power is fluctuating because of the uncertain nature of wind, whereas wind shear and tower shadow effects also cause periodic fluctuations. These may lead to serious forced...... oscillation when the frequencies of the periodic fluctuations are close to the natural oscillation frequencies of the connected power system. By using modal analysis and time-domain simulations, this study studies the forced oscillation caused by the wind shear and tower shadow effects. Three forced...

HUSUM Wind Energy 2012 - side event on wind energy in France

International Nuclear Information System (INIS)

Wolff, Nicolas; Cassin, Fabrice

2012-01-01

The French-German office for Renewable energies (OFAEnR) organised a conference on wind energy in France. In the framework of this French-German exchange of experience, about a hundred participants exchanged views on the status of the French wind energy market and to present the perspectives of this industry for the coming years. Emphasis was given on the legal framework and on the authorization procedures actually in force. This document brings together the two presentations (slides) made during this event: 1 - Current status and perspectives of the French wind energy market (Nicolas Wolff); 2 - Regulatory framework for wind energy and authorisation procedures in France (Fabrice Cassin)

Design of the pancake-winding central solenoid coil

International Nuclear Information System (INIS)

Yoshida, Kiyoshi; Nishi, Masataka; Tsuji, Hirosi

1995-01-01

There was a debate over whether a pancake-winding or layer-winding technique is more appropriate for the Central Solenoid (CS) coil for ITER superconducting magnet. The layer-winding CS has the advantage of homogeneous winding supporting the TF centering force without weak joints, but has many difficulties during manufacturing and quality control. On other hand, the pancake-winding has the advantage of better quality control during manufacturing and module testing but has difficulties with joints and feeders, and pipes located in the load path of the bucking force from the toroidal field coils. The compact joints, reinforcement by preformed amour, sharp bending, and double seals are applied to the design of pancake-winding CS coil and demonstrated by hardware developments. The pancake-winding CS coil by using modified existing technology is compatible with the bucking concept of the ITER magnet system. (author)

Fracture Mechanics Models for Brittle Failure of Bottom Rails due to Uplift in Timber Frame Shear Walls

Directory of Open Access Journals (Sweden)

Joergen L. Jensen

2016-01-01

Full Text Available In partially anchored timber frame shear walls, hold-down devices are not provided; hence the uplift forces are transferred by the fasteners of the sheathing-to-framing joints into the bottom rail and via anchor bolts from the bottom rail into the foundation. Since the force in the anchor bolts and the sheathing-to-framing joints do not act in the same vertical plane, the bottom rail is subjected to tensile stresses perpendicular to the grain and splitting of the bottom rail may occur. This paper presents simple analytical models based on fracture mechanics for the analysis of such bottom rails. An existing model is reviewed and several alternative models are derived and compared qualitatively and with experimental data. It is concluded that several of the fracture mechanics models lead to failure load predictions which seem in sufficiently good agreement with the experimental results to justify their application in practical design.

Determination of performance parameters of vertical axis wind turbines in wind tunnel

Directory of Open Access Journals (Sweden)

Nguyen Van Bang

2017-01-01

Full Text Available The paper deals with the determination of the performance parameters of a small vertical axis wind turbines (VAWT, which operate by the utilization of drag forces acting on the blades of the turbine. The performance was evaluated by investigating the electrical power output and torque moment of the wind machine. Measurements were performed on the full-scale model and the experimental data are assessed and compared to other types of wind turbines, with respect to its purpose.

Ice Accretion on Wind Turbine Blades

DEFF Research Database (Denmark)

Hudecz, Adriána; Koss, Holger; Hansen, Martin Otto Laver

2013-01-01

In this paper, both experimental and numerical simulations of the effects of ice accretion on a NACA 64-618 airfoil section with 7° angle of attack are presented. The wind tunnel tests were conducted in a closed-circuit climatic wind tunnel at Force Technology in Denmark. The changes of aerodynamic...... forces were monitored as ice was building up on the airfoil for glaze, rime and mixed ice. In the first part of the numerical analysis, the resulted ice profiles of the wind tunnel tests were compared to profiles estimated by using the 2D ice accretion code TURBICE. In the second part, Ansys Fluent...... of the rime iced ice profile follows the streamlines quite well, disturbing the flow the least. The TURBICE analysis agrees fairly with the profiles produced during the wind tunnel testing....

Sombrero uplift above the Altiplano-Puna Magma Body: evidence of a ballooning mid-crustal diapir.

Science.gov (United States)

Fialko, Yuri; Pearse, Jill

2012-10-12

The Altiplano-Puna ultralow-velocity zone in the central Andes, South America, is the largest active magma body in Earth's continental crust. Space geodetic observations reported an uplift in the Altiplano-Puna proper at a rate of ~10 mm/year; however, the nature of the inferred inflation source has been uncertain. We present data showing that the uplift has persisted at a nearly constant rate over the past two decades, and is surrounded by a broad zone of subsidence. We show that the ongoing uplift and peripheral subsidence may result from a large mid-crustal diapir fed by partial melt from the Altiplano-Puna Magma Body.

Ski jumping takeoff in a wind tunnel with skis.

Science.gov (United States)

Virmavirta, Mikko; Kivekäs, Juha; Komi, Paavo

2011-11-01

The effect of skis on the force-time characteristics of the simulated ski jumping takeoff was examined in a wind tunnel. Takeoff forces were recorded with a force plate installed under the tunnel floor. Signals from the front and rear parts of the force plate were collected separately to examine the anteroposterior balance of the jumpers during the takeoff. Two ski jumpers performed simulated takeoffs, first without skis in nonwind conditions and in various wind conditions. Thereafter, the same experiments were repeated with skis. The jumpers were able to perform very natural takeoff actions (similar to the actual takeoff) with skis in wind tunnel. According to the subjective feeling of the jumpers, the simulated ski jumping takeoff with skis was even easier to perform than the earlier trials without skis. Skis did not much influence the force levels produced during the takeoff but they still changed the force distribution under the feet. Contribution of the forces produced under the rear part of the feet was emphasized probably because the strong dorsiflexion is needed for lifting the skis to the proper flight position. The results presented in this experiment emphasize that research on ski jumping takeoff can be advanced by using wind tunnels.

Uplifting model of the Longmenshan mountain in the eastern margin of Tibetan plateau

Science.gov (United States)

Zhang, S.; Ding, R.; Mao, C.

2010-12-01

Longmenshan mountain is a vivid manifestation of the Cenozoic orogenesis in the eastern margin of the Tibetan plateau, and a key to understand the geodynamics of eastward extending of the plateau. Thus the uplift mechanism of Longmenshan mountain became a hot spot issue of geosciences about the Tibetan plateau. Two entirely different hypotheses, i.e., crustal shortening and lower crustal channel flow, were put forward, but the solution is open. Further discussion need our deeper understanding about the uplifting features of the Longmenshan mountain. Fortunately, the uplifting processes were recorded objectively by peneplains and river landforms. We first analysed the peneplains and pediplanes of Longmenshan mountain and its surrounding areas, and surveyed the terraces of Dadu river running across the mountain. Then we studied the uplifting features of the study areas in late Cenozoic time on the basis of landform geometries. Finaly we discussed the possible mechanisms for the uplifting. There are two levels of peneplains whose peneplanations may begin in early Cenozoic time and end at late Miocene when the final fluctuations of elevations were possibly less than one kilometers. The valley of Dadu river is incised into the peneplains and has a staircase of no less than ten levels of terraces. The highest terrace is a strath which was contemporary with the pediplane in the piedmont formed in late Pliocene or in early Pleistocene. Due to their originally flat features, the peneplains and the strath terraces were used as datum planes for judging neotectonic deformations. Since late Miocene, the southeastern side of Longmenshan mountain has been dominated by thrust-faulting with a total vertical displacement of about 4500 m against the Sichuan basin, meantime the northwest side has been maintained flexural uplift with syncline hinge approximately following the Longriba fault. As a landform barrier between Tibetan plateau and Sichuan basin, the crest lines of the

RIVERTON DOME GAS EXPLORATION AND STIMULATION TECHNOLOGY DEMONSTRATION, WIND RIVER BASIN, WYOMING

International Nuclear Information System (INIS)

Dr. Ronald C. Surdam

1999-01-01

This project will provide a full demonstration of an entirely new package of exploration technologies that will result in the discovery and development of significant new gas reserves now trapped in unconventional low-permeability reservoirs. This demonstration includes the field application of these technologies, prospect definition and well siting, and a test of this new strategy through wildcat drilling. In addition this project includes a demonstration of a new stimulation technology that will improve completion success in these unconventional low permeability reservoirs which are sensitive to drilling and completion damage. The work includes two test wells to be drilled by Snyder Oil Company on the Shoshone/Arapahoe Tribal Lands in the Wind River Basin. This basin is a foreland basin whose petroleum systems include Paleozoic and Cretaceous source beds and reservoirs which were buried, folded by Laramide compressional folding, and subsequently uplifted asymmetrically. The anomalous pressure boundary is also asymmetric, following differential uplift trends

Radiation-driven winds in x-ray binaries

International Nuclear Information System (INIS)

Friend, D.B.; Castor, J.I.

1982-01-01

We discuss the properties of a radiation-driven stellar wind in an X-ray binary system. The Castor, Abbott, Klein line-driven wind model is used, but the effects of the compact companion (gravity and continuum radiation pressure) and the centrifugal force due to orbital motion are included. These forces destroy the spherical symmetry of the wind and can make the mass loss and accretion strong functions of the size of the primary relative to its critical potential lobe. We in most systems the wind alone could power the X-ray emission. It also appears that, in the evolution of these systems, there would be a continuous transition from wind accretion to critical potential lobe overflow. The model is also used to make a prediction about the nature of a suspected binary system which is not known to be an X-ray emitter

Wind energy conversion system

Science.gov (United States)

Longrigg, Paul

1987-01-01

The wind energy conversion system includes a wind machine having a propeller connected to a generator of electric power, the propeller rotating the generator in response to force of an incident wind. The generator converts the power of the wind to electric power for use by an electric load. Circuitry for varying the duty factor of the generator output power is connected between the generator and the load to thereby alter a loading of the generator and the propeller by the electric load. Wind speed is sensed electro-optically to provide data of wind speed upwind of the propeller, to thereby permit tip speed ratio circuitry to operate the power control circuitry and thereby optimize the tip speed ratio by varying the loading of the propeller. Accordingly, the efficiency of the wind energy conversion system is maximized.

Determining the Probability of Violating Upper-Level Wind Constraints for the Launch of Minuteman Ill Ballistic Missiles At Vandenberg Air Force Base

Science.gov (United States)

Shafer, Jaclyn A.; Brock, Tyler M.

2013-01-01

The 30th Operational Support Squadron Weather Flight (30 OSSWF) provides comprehensive weather services to the space program at Vandenberg Air Force Base (VAFB) in California. One of their responsibilities is to monitor upper-level winds to ensure safe launch operations of the Minuteman Ill ballistic missile. The 30 OSSWF requested the Applied Meteorology Unit (AMU) analyze VAFB sounding data to determine the probability of violating (PoV) upper-level thresholds for wind speed and shear constraints specific to this launch vehicle, and to develop a graphical user interface (GUI) that will calculate the PoV of each constraint on the day of launch. The AMU suggested also including forecast sounding data from the Rapid Refresh (RAP) model. This would provide further insight for the launch weather officers (LWOs) when determining if a wind constraint violation will occur over the next few hours, and help to improve the overall upper winds forecast on launch day.

Numerical Investigation of the Turbulent Wind Flow Through Elevated Windbreak

Science.gov (United States)

Agarwal, Ashish; Irtaza, Hassan

2018-04-01

Analysis of airflow through elevated windbreaks is presented in this paper. Permeable nets and impermeable film increases considerable wind forces on the windbreaks which is susceptible to damage during high wind. A comprehensive numerical investigation has been carried out to analyze the effects of wind on standalone elevated windbreak clad with various permeable nets and an impermeable film. The variation of airflow behavior around and through permeable nets and airflow behavior around impermeable film were also been investigated. Computational fluid dynamics techniques using Reynolds Averaged Navier-Stokes equations has been used to predict the wind force coefficient and thus wind forces on panels supporting permeable nets and impermeable film for turbulent wind flow. Elevated windbreak panels were analyzed for seven different permeable nets having various solidity ratio, specific permeability and aerodynamic resistant coefficients. The permeable nets were modelled as porous jump media obeying Forchheimer's law and an impermeable film modelled as rigid wall.

Numerical Investigation of the Turbulent Wind Flow Through Elevated Windbreak

Science.gov (United States)

Agarwal, Ashish; Irtaza, Hassan

2018-06-01

Analysis of airflow through elevated windbreaks is presented in this paper. Permeable nets and impermeable film increases considerable wind forces on the windbreaks which is susceptible to damage during high wind. A comprehensive numerical investigation has been carried out to analyze the effects of wind on standalone elevated windbreak clad with various permeable nets and an impermeable film. The variation of airflow behavior around and through permeable nets and airflow behavior around impermeable film were also been investigated. Computational fluid dynamics techniques using Reynolds Averaged Navier-Stokes equations has been used to predict the wind force coefficient and thus wind forces on panels supporting permeable nets and impermeable film for turbulent wind flow. Elevated windbreak panels were analyzed for seven different permeable nets having various solidity ratio, specific permeability and aerodynamic resistant coefficients. The permeable nets were modelled as porous jump media obeying Forchheimer's law and an impermeable film modelled as rigid wall.

Land uplift in the Olkiluoto-Pyhaejaervi area, southwestern Finland, during the last 8000 years

International Nuclear Information System (INIS)

Eronen, M.; Glueckert, G.; Rantala, P.; Plassche, O. van de; Plicht, J. van der

1995-12-01

Land is rising in relation to sea level several millimetres per year on the coast of southwestern Finland. The aim of the study was to gather information about the land uplift process. Sediment samples were collected from 14 lakes lying at different altitudes in the area between Olkiluoto and Lake Pyhaejaervi in southwestern Finland to study the relative sea-level changes and land uplift. The present-day lakes had once been below the waters of the Baltic, but due to uplift they had been isolated from the sea one after another. The isolation points in the sediments were determined by preliminary diatom analyses. They show the change from brackish to fresh-water conditions, and these horizons were then dated by two radiocarbon assays. (37 refs., 18 figs., 1 tab.)

Zonation of uplifted pleistocene coral reefs on barbados, west indies.

Science.gov (United States)

Mesolella, K J

1967-05-05

The coral species composition of uplifted Pleistocene reefs on Barbados is very similar to Recent West Indian reefs. Acropora palmata, Acropora cervicornis, and Montastrea annularis are qtuantitatively the most important of the coral species.

Wind Observatory 2017. Analysis of the wind power market, wind jobs and future of the wind industry in France

International Nuclear Information System (INIS)

2017-09-01

Two years after the enactment of the Energy Transition for Green Growth Act, wind power capacity continues to grow in France, exceeding 12 GWatt the end of 2016 and soon to account for 5% of France's electric power consumption. This vitality, which is set to continue in 2017, will help France achieve its objectives of an installed capacity of 15,000 MW in onshore wind by 2018 and 21,800 to 26,000 MW by 2023. The current pace will nevertheless have to be accelerated in order to reach the realistic objective of 26 GW by 2023 mentioned in the multi-annual energy plan (PPE). With 1,400 jobs created in one year and more than 3,300 over the last two years, the relevance of wind power as a driving force of sustainable job creation throughout the country is unequivocally confirmed: the increase in wind power capacity continues to contribute to the growth in employment in the country. Prepared in collaboration with the consulting firm BearingPoint, the 2017 edition of the Observatory aims to give the reader an overview of employment in the wind industry and the wind power market over the period under consideration. Any changes from the three previous editions are highlighted. It is based on a comprehensive census of all market participants on three themes: employment, the market and the future of wind power. The Observatory gives an accurate picture of how the wind energy industry is structured, thereby presenting a precise overview of the wind energy industry and all its components

Study of wind forces on low-rise hip-roof building

African Journals Online (AJOL)

DR OKE

to predict the wind loads and the flow patterns around the hip-roof building. .... various wind angle attack on the roof using CFD simulation. .... SIMPLE algorithm substitutes the flux correction equations into the discrete continuity equation to ...

Estimation of uncertainty of wind energy predictions with application to weather routing and wind power generation

CERN Document Server

Zastrau, David

2017-01-01

Wind drives in combination with weather routing can lower the fuel consumption of cargo ships significantly. For this reason, the author describes a mathematical method based on quantile regression for a probabilistic estimate of the wind propulsion force on a ship route.

Method and apparatus for wind turbine braking

Science.gov (United States)

Barbu, Corneliu [Laguna Hills, CA; Teichmann, Ralph [Nishkayuna, NY; Avagliano, Aaron [Houston, TX; Kammer, Leonardo Cesar [Niskayuna, NY; Pierce, Kirk Gee [Simpsonville, SC; Pesetsky, David Samuel [Greenville, SC; Gauchel, Peter [Muenster, DE

2009-02-10

A method for braking a wind turbine including at least one rotor blade coupled to a rotor. The method includes selectively controlling an angle of pitch of the at least one rotor blade with respect to a wind direction based on a design parameter of a component of the wind turbine to facilitate reducing a force induced into the wind turbine component as a result of braking.

Tectonic and erosion-driven uplift in the Gamburtsev Subglacial Mountains of East Antarctica

Science.gov (United States)

Ferraccioli, Fausto; Jordan, Tom; Watts, Tony; Bell, Robin; Jamieson, Stewart; Finn, Carol; Damaske, Detlef

2014-05-01

Understanding the mechanisms leading to intraplate mountain building remains a significant challenge in Earth Sciences compared to ranges formed along plate margins. The most enigmatic intraplate mountain range on Earth is the Gamburtsev Subglacial Mountains (GSM) located in the middle of the Precambrian East Antarctic Craton. During the International Polar Year, the AGAP project acquired 120,000 line km of new airborne geophysical data (Bell et al., 2011, Science) and seismological observations (Hansen et al., 2010, EPSL) across central East Antarctica. Models derived from these datasets provide new geophysical perspectives on crustal architecture and possible uplift mechanisms for the enigmatic GSM (Ferraccioli et al., 2011, Nature). The geophysical data define a 2,500-km-long Paleozoic to Mesozoic rift system in East Antarctica surrounding the GSM. A thick high-density lower crustal root is partially preserved beneath the range and has been interpreted as formed during the Proterozoic assembly of East Antarctica. Rifting could have triggered phase/density changes at deep crustal levels, perhaps restoring some of the latent root buoyancy, as well as causing rift-flank uplift. Permian rifting is well-established in the adjacent Lambert Rift, and was followed by Cretaceous strike-slip faulting and transtension associated with Gondwana break-up; this phase may have provided a more recent tectonic trigger for the initial uplift of the modern GSM. The Cretaceous rift-flank uplift model for the Gamburtsevs is appealing because it relates the initiation of intraplate mountain-building to large-scale geodynamic processes that led to the separation of Greater India from East Antarctica. It is also consistent with several geological and geophysical interpretations within the Lambert Rift. However, recent detrital thermochrology results from Oligocene-Quaternary sediments in Prydz Bay (Tochlin et al., 2012, G3) argue against the requirement for major Cretaceous rift

Uplift, thermal unrest and magma intrusion at Yellowstone caldera.

Science.gov (United States)

Wicks, Charles W; Thatcher, Wayne; Dzurisin, Daniel; Svarc, Jerry

2006-03-02

The Yellowstone caldera, in the western United States, formed approximately 640,000 years ago when an explosive eruption ejected approximately 1,000 km3 of material. It is the youngest of a series of large calderas that formed during sequential cataclysmic eruptions that began approximately 16 million years ago in eastern Oregon and northern Nevada. The Yellowstone caldera was largely buried by rhyolite lava flows during eruptions that occurred from approximately 150,000 to approximately 70,000 years ago. Since the last eruption, Yellowstone has remained restless, with high seismicity, continuing uplift/subsidence episodes with movements of approximately 70 cm historically to several metres since the Pleistocene epoch, and intense hydrothermal activity. Here we present observations of a new mode of surface deformation in Yellowstone, based on radar interferometry observations from the European Space Agency ERS-2 satellite. We infer that the observed pattern of uplift and subsidence results from variations in the movement of molten basalt into and out of the Yellowstone volcanic system.

Geomorphic Response to Spatial and Temporal Tectonic uplift on the Kenya Rift of East African Rift System

Science.gov (United States)

Xue, L.; Abdelsalam, M. G.

2017-12-01

Tectonic uplifts of the shoulders of the East Africa Rift System (EARS) have significant impact on the geological record by reorganizing drainage systems, increasing sediment supply, and changing climate and biogeography. Recent studies in geochronology, geomorphology and geophysics have provided some understanding of the timing of tectonic uplift and its distribution pattern of the (EARS). We do not know how the vertical motion is localized along the rift axis and the relative roles of upwelling of magma and rift extensional processes play in tectonic uplift history. This work presents detailed morphometric study of the fluvial landscape response to the tectonic uplift and climate shifting of the Kenya Rift shoulders in order to reconstruct their incision history, with special attention to timing, location, and intensity of uplift episodes. This work compiles the Shuttle Radar Topography Mission (SRTM) Digital Elevation Model (DEM) and Sentinel-2A data, summarized previous 39Ar-40Ar and thermochronology data, and calculates long-term incision rate and geomorphic proxies (normalized steepness and chi-integral) along the Kenya Rift. It also models the age of tectonic/climatic events by using knickpoint celerity model and R/SR integrative approach. It found that the maximum long-term incision rates of 300 mm/kyr to be at the central Kenya Rift, possibly related to the mantle-driven process and rapid tectonic uplift. The geomorphic proxies indicate southward decreasing pattern of the short-term incision rate, possibly related to the migration of the mantle plume.

Seismic Performance of CAP1400 Nuclear Power Station considering Foundation Uplift

Directory of Open Access Journals (Sweden)

Ling-Yun Peng

2018-01-01

Full Text Available Under earthquake action, the reinforced concrete structure at the edge of the CAP1400 nuclear power plant foundation slab will be uplifted. In order to determine the seismic performance of this structure, a 1 : 12 scale shaking table test model was fabricated using gypsum as simulated concrete in order to meet scaled design requirements. By testing this model, the seismic response of the structure with consideration of the foundation uplift was obtained. Numerical analyses of the test model and the prototype structure were conducted to gain a better understanding of the structural seismic performance. When subjected to earthquakes, the foundation slab of the nuclear power plant experiences a slight degree of uplift but remains in the elastic stage due to the weight of the structure above, which provides an antioverturning moment. The numerical simulation is in general agreement with the test results, suggesting numerical simulations could be accurately employed in place of physical tests. The superstructure displacement response was found not to affect the safety of adjacent structures, and the seismic performance of the structure was shown to meet the relevant design requirements, demonstrating that this approach to modelling can serve as a design basis for the CAP1400 nuclear power demonstration project.

Modelling the Middle Pleistocene uplift in the Ardennes-Rhenish Massif: Thermo-mechanical weakening under the Eifel?

NARCIS (Netherlands)

Garcia-Castellanos, D.; Cloetingh, S.A.P.L.; van Balen, R.T.

2000-01-01

Middle Pleistocene uplift in the Eifel has been interpreted as the isostatic response of the lithosphere to a deep buoyant hot body. The spatial and temporal distribution of the uplift in the Ardennes-Rhenish Massif Region has recently been constrained by new data of river incision that have been

Empirical models of wind conditions on Upper Klamath Lake, Oregon

Science.gov (United States)

Buccola, Norman L.; Wood, Tamara M.

2010-01-01

Upper Klamath Lake is a large (230 square kilometers), shallow (mean depth 2.8 meters at full pool) lake in southern Oregon. Lake circulation patterns are driven largely by wind, and the resulting currents affect the water quality and ecology of the lake. To support hydrodynamic modeling of the lake and statistical investigations of the relation between wind and lake water-quality measurements, the U.S. Geological Survey has monitored wind conditions along the lakeshore and at floating raft sites in the middle of the lake since 2005. In order to make the existing wind archive more useful, this report summarizes the development of empirical wind models that serve two purposes: (1) to fill short (on the order of hours or days) wind data gaps at raft sites in the middle of the lake, and (2) to reconstruct, on a daily basis, over periods of months to years, historical wind conditions at U.S. Geological Survey sites prior to 2005. Empirical wind models based on Artificial Neural Network (ANN) and Multivariate-Adaptive Regressive Splines (MARS) algorithms were compared. ANNs were better suited to simulating the 10-minute wind data that are the dependent variables of the gap-filling models, but the simpler MARS algorithm may be adequate to accurately simulate the daily wind data that are the dependent variables of the historical wind models. To further test the accuracy of the gap-filling models, the resulting simulated winds were used to force the hydrodynamic model of the lake, and the resulting simulated currents were compared to measurements from an acoustic Doppler current profiler. The error statistics indicated that the simulation of currents was degraded as compared to when the model was forced with observed winds, but probably is adequate for short gaps in the data of a few days or less. Transport seems to be less affected by the use of the simulated winds in place of observed winds. The simulated tracer concentration was similar between model results when

Aerodynamic analysis of S series wind turbine airfoils by using X foil technique

International Nuclear Information System (INIS)

Zaheer, M.A.; Munir, M.A.; Zahid, I.; Rizwan, M.

2015-01-01

In order to attain supreme energy from wind turbine economically, blade profile enactment must be acquired. For extracting extreme power from wind, it is necessary to develop rotor models of wind turbine which have high rotation rates and power coefficients. Maximum power can also be haul out by using suitable airfoils at root and tip sections of wind turbine blades. In this research four different S-series airfoils have been selected to study their behavior for maximum power extraction from wind. The wind conditions during the research were scertained from the wind speeds over Kallar Kahar Pakistan. In order to study the wind turbine operation, the extremely important parameters are lift and drag forces. Therefore an endeavor to study lift force and drag force at various sections of wind turbine blade is shown in current research. In order to acquire the utmost power from wind turbine, highest value of sliding ratio is prerequisite. At various wind speeds, performance of several blade profiles was analyzed and for every wind speed, the appropriate blade profile is ascertained grounded on the utmost sliding ratio. For every airfoil, prime angle of attack is resolute at numerous wind speeds. (author)

Dynamics of Line-Driven Winds from Disks in Cataclysmic Variables. I. Solution Topology and Wind Geometry

OpenAIRE

Feldmeier, Achim; Shlosman, Isaac

1999-01-01

We analyze the dynamics of 2-D stationary, line-driven winds from accretion disks in cataclysmic variable stars. The driving force is that of line radiation pressure, in the formalism developed by Castor, Abbott & Klein for O stars. Our main assumption is that wind helical streamlines lie on straight cones. We find that the Euler equation for the disk wind has two eigenvalues, the mass loss rate and the flow tilt angle with the disk. Both are calculated self-consistently. The wind is characte...

Thermal history of the Kunlun batholith, N. Tibet, and implications for uplift of the Tibetan plateau

International Nuclear Information System (INIS)

Lewis, C.L.E.

1990-01-01

Preliminary Rb-Sr and 40 Ar/ 39 Ar biotite ages combined with zircon and apatite fission track dates from the Hunlun batholith in northern Tibet allow for comparison with the previously established uplift history of southern Tibet, and inferences to be made about uplift of the plateau as a whole. Across a major divide at the Golmud Fault, apatite ages decrease from 100 Ma in the north to 20 Ma in the south. This is believed to be as a result of a thrusting event at 120 Ma which uplifted the Northern block and overthrust the Southern block to the south. Subsequent to this event, surface approach rates of less than 70 m Ma -1 from biotite closure at 120 Ma to apatite cooling at 20 Ma in the Southern block, indicate a long uninterrupted period of thermal equilibration in an essentially static continental block. Mean confined track lengths of 12.5-13.5 μm in apatites suggest that samples exposed at the surface today resided in the fission track partial annealing zone prior to the onset of uplift which must have occurred subsequent to 20 Ma. This indicates that at least 3-4 km have been uplifted since this time and that the onset of this phase could have been as recent as 8 Ma. (author)

Wind energy in 1996: Looking forward, looking back

Energy Technology Data Exchange (ETDEWEB)

Swisher, R.

1996-12-31

Opinions on the world market for wind power are presented in this paper. A brief review of progress in wind energy is given. The impact of world market forces and restructuring of the electric industry in the U.S. on the wind energy market are discussed. An outline of the American Wind Energy Association`s Renewables Portfolio Standard is presented. Legislative activities in wind energy are also reviewed.

Barotropic response in a lake to wind-forcing

Directory of Open Access Journals (Sweden)

Y. Wang

2001-03-01

Full Text Available We report results gained with a three-dimensional, semi-implicit, semi-spectral model of the shallow water equations on the rotating Earth that allowed one to compute the wind-induced motion in lakes. The barotropic response to unidirectional, uniform winds, Heaviside in time, is determined in a rectangular basin with constant depth, and in Lake Constance, for different values and vertical distributions of the vertical eddy viscosities. It is computationally demonstrated that both the transitory oscillating, as well as the steady state current distribution, depends strongly upon the absolute value and vertical shape of the vertical eddy viscosity. In particular, the excitation and attenuation in time of the inertial waves, the structure of the Ekman spiral, the thickness of the Ekman layer, and the exact distribution and magnitude of the upwelling and downwelling zones are all significantly affected by the eddy viscosities. Observations indicate that the eddy viscosities must be sufficiently small so that the oscillatory behaviour can be adequately modelled. Comparison of the measured current-time series at depth in one position of Lake Constance with those computed on the basis of the measured wind demonstrates fair agreement, including the rotation-induced inertial oscillation.Key words. Oceanography: general (limnology – Oceanography: physical (Coriolis effects; general circulation

Barotropic response in a lake to wind-forcing

Directory of Open Access Journals (Sweden)

Y. Wang

Full Text Available We report results gained with a three-dimensional, semi-implicit, semi-spectral model of the shallow water equations on the rotating Earth that allowed one to compute the wind-induced motion in lakes. The barotropic response to unidirectional, uniform winds, Heaviside in time, is determined in a rectangular basin with constant depth, and in Lake Constance, for different values and vertical distributions of the vertical eddy viscosities. It is computationally demonstrated that both the transitory oscillating, as well as the steady state current distribution, depends strongly upon the absolute value and vertical shape of the vertical eddy viscosity. In particular, the excitation and attenuation in time of the inertial waves, the structure of the Ekman spiral, the thickness of the Ekman layer, and the exact distribution and magnitude of the upwelling and downwelling zones are all significantly affected by the eddy viscosities. Observations indicate that the eddy viscosities must be sufficiently small so that the oscillatory behaviour can be adequately modelled. Comparison of the measured current-time series at depth in one position of Lake Constance with those computed on the basis of the measured wind demonstrates fair agreement, including the rotation-induced inertial oscillation.

Key words. Oceanography: general (limnology – Oceanography: physical (Coriolis effects; general circulation

Propulsion and airframe aerodynamic interactions of supersonic V/STOL configurations. Volume 2: Wind tunnel test force and moment data report

Science.gov (United States)

Zilz, D. E.

1985-01-01

A wind tunnel model of a supersonic V/STOL fighter configuration has been tested to measure the aerodynamic interaction effects which can result from geometrically close-coupled propulsion system/airframe components. The approach was to configure the model to represent two different test techniques. One was a conventional test technique composed of two test modes. In the Flow-Through mode, absolute configuration aerodynamics are measured, including inlet/airframe interactions. In the Jet-Effects mode, incremental nozzle/airframe interactions are measured. The other test technique is a propulsion simulator approach, where a sub-scale, externally powered engine is mounted in the model. This allows proper measurement of inlet/airframe and nozzle/airframe interactions simultaneously. This is Volume 2 of 2: Wind Tunnel Test Force and Moment Data Report.

Wind tower service lift

Science.gov (United States)

Oliphant, David; Quilter, Jared; Andersen, Todd; Conroy, Thomas

2011-09-13

An apparatus used for maintaining a wind tower structure wherein the wind tower structure may have a plurality of legs and may be configured to support a wind turbine above the ground in a better position to interface with winds. The lift structure may be configured for carrying objects and have a guide system and drive system for mechanically communicating with a primary cable, rail or other first elongate member attached to the wind tower structure. The drive system and guide system may transmit forces that move the lift relative to the cable and thereby relative to the wind tower structure. A control interface may be included for controlling the amount and direction of the power into the guide system and drive system thereby causing the guide system and drive system to move the lift relative to said first elongate member such that said lift moves relative to said wind tower structure.

The estimation of future surface water bodies at Olkiluoto area based on statistical terrain and land uplift models

Energy Technology Data Exchange (ETDEWEB)

Pohjola, J.; Turunen, J.; Lipping, T. [Tampere Univ. of Technology (Finland); Ikonen, A.

2014-03-15

In this working report the modelling effort of future landscape development and surface water body formation at the modelling area in the vicinity of the Olkiluoto Island is presented. Estimation of the features of future surface water bodies is based on probabilistic terrain and land uplift models presented in previous working reports. The estimation is done using a GIS-based toolbox called UNTAMO. The future surface water bodies are estimated in 10 000 years' time span with 1000 years' intervals for the safety assessment of disposal of spent nuclear fuel at the Olkiluoto site. In the report a brief overview on the techniques used for probabilistic terrain modelling, land uplift modelling and hydrological modelling are presented first. The latter part of the report describes the results of the modelling effort. The main features of the future landscape - the four lakes forming in the vicinity of the Olkiluoto Island - are identified and the probabilistic model of the shoreline displacement is presented. The area and volume of the four lakes is modelled in a probabilistic manner. All the simulations have been performed for three scenarios two of which are based on 10 realizations of the probabilistic digital terrain model (DTM) and 10 realizations of the probabilistic land uplift model. These two scenarios differ from each other by the eustatic curve used in the land uplift model. The third scenario employs 50 realizations of the probabilistic DTM while a deterministic land uplift model, derived solely from the current land uplift rate, is used. The results indicate that the two scenarios based on the probabilistic land uplift model behave in a similar manner while the third model overestimates past and future land uplift rates. The main features of the landscape are nevertheless similar also for the third scenario. Prediction results for the volumes of the future lakes indicate that a couple of highly probably lake formation scenarios can be identified

The estimation of future surface water bodies at Olkiluoto area based on statistical terrain and land uplift models

International Nuclear Information System (INIS)

Pohjola, J.; Turunen, J.; Lipping, T.; Ikonen, A.

2014-03-01

In this working report the modelling effort of future landscape development and surface water body formation at the modelling area in the vicinity of the Olkiluoto Island is presented. Estimation of the features of future surface water bodies is based on probabilistic terrain and land uplift models presented in previous working reports. The estimation is done using a GIS-based toolbox called UNTAMO. The future surface water bodies are estimated in 10 000 years' time span with 1000 years' intervals for the safety assessment of disposal of spent nuclear fuel at the Olkiluoto site. In the report a brief overview on the techniques used for probabilistic terrain modelling, land uplift modelling and hydrological modelling are presented first. The latter part of the report describes the results of the modelling effort. The main features of the future landscape - the four lakes forming in the vicinity of the Olkiluoto Island - are identified and the probabilistic model of the shoreline displacement is presented. The area and volume of the four lakes is modelled in a probabilistic manner. All the simulations have been performed for three scenarios two of which are based on 10 realizations of the probabilistic digital terrain model (DTM) and 10 realizations of the probabilistic land uplift model. These two scenarios differ from each other by the eustatic curve used in the land uplift model. The third scenario employs 50 realizations of the probabilistic DTM while a deterministic land uplift model, derived solely from the current land uplift rate, is used. The results indicate that the two scenarios based on the probabilistic land uplift model behave in a similar manner while the third model overestimates past and future land uplift rates. The main features of the landscape are nevertheless similar also for the third scenario. Prediction results for the volumes of the future lakes indicate that a couple of highly probably lake formation scenarios can be identified with other

Flexurally-resisted uplift of the Tharsis Province, Mars

International Nuclear Information System (INIS)

Phillips, R.J.; Sleep, N.H.

1987-01-01

The tectonic style of Mars is dominated by vertical motion, perhaps more than any of the terrestrial planets. The imprint of this tectonic activity has left a surface widely faulted even though younger volcanism has masked the expression of tectonism in many places. Geological activity associated with the Tharsis and, to a lesser extent, Elysium provinces is responsible for a significant portion of this faulting, while the origins of the remaining features are enigmatic in many cases. The origin and evolution of the Tharsis and Elysium provinces, in terms of their great elevation, volcanic activity, and tectonic style, has sparked intense debate over the last fifteen years. Central to these discussions are the relative roles of structural uplift and volcanic construction in the creation of immense topographic relief. For example, it is argued that the presence of very old and cratered terrain high on the Tharsis rise, in the vicinity of Claritas Fossae, points to structural uplift of an ancient crust. Others have pointed out, however, that there is no reason that this terrain could not be of volcanic origin and thus part of the constructional mechanism

Quantification of surface uplift by using paleo beach deposits (Oman, Northern Indian Ocean)

Science.gov (United States)

Hoffmann, Gösta; Schneider, Bastian; Monschau, Martin; Mechernich, Silke

2017-04-01

The study focusses on a coastal area along the Arabian Sea in Oman. Here, a staircase of marine terraces is seen as geomorphological evidence suggesting sub-recent uplift of a crustal block in the northeast of the Arabian Peninsula. The erosional terraces are cut into Paleocene to Early Eocene limestone formations. These limestone formations are underlain by allochtonous ophiolites. We mapped the terraces over a distance of 60 km and identified at least 8 terrace levels in elevations up to 350 m above present sea level. The uppermost terraces are erosional, whereas the lower ones are depositional in style. Mollusc and coral remains as well as beach-rock are encountered on the terrace surfaces. The formations are dissected by NW-SE trending faults. Some of the terraces are very pronounced features in the landscape and easy to trace, others are partly eroded and preserved as remnants only. The deposit along the shoreline angle act as a datum making use of the fact that the rocks formed in a defined horizontal level which is the paleo-sea level. Hence, any offset from the primary depositional level is evidence for neotectonic movements. We utilise differential GPS to map the elevation of beachrock deposits. Age constraints on terrace formation is derived by sampling the beachrock deposits and dating using cosmogenic nuclii. The results indicate ongoing uplift in the range of less than a millimetre per year. The uplift is differential as the terraces are tilted. We mapped oblique normal and strike-slip faults in the younger terraces. We hypothesise that the mechanism responsible for the uplift is not tectonics but driven by the serpentinisation of the ophiolite that underlie the limestone formations. One process during the serpentinisation is the hydration of the mantle rocks which is responsible for a decrease in density. The resulting buoyancy and significant solid volume increase lead to the observed deformation including uplift.

Middel Pleistocene to Holocene fluvial terrace development and uplift-driven valley incision in the SE Carpathians, Romania

NARCIS (Netherlands)

Necea, D.; Fielitz, W.; Andriessen, P.A.M.; Dinu, C.

2013-01-01

This study reveals that in the SE Carpathians terrace development and fluvial incision during the Middle Pleistocene-Holocene are predominantly controlled by tectonic uplift as shown by terrace distributions and uplift amounts and rates. The work focuses on a transect from the internal nappes and

Wind energy potential in Peshawar, Pakistan

International Nuclear Information System (INIS)

Nasir, S.M.; Raza, S.M.

1994-01-01

Hourly wind data at Peshawar airport, received from the Headquarters, Pakistan Air Force, has been used to determine the diurnal variations, speed duration and speed frequency curves. The applicability of Weibull distribution is then tested over probability density function, which shows that weibull distribution fits the wind data satisfactorily and with a good precision, provided the observations of calm spells are omitted. Our analysis shows that monthly mean wind speed and wind power varies from 0.6 to 2.0 m/s and 0.2 to 4.0 wm-2, respectively, giving fair prospects for wind owe applications over the summer months. (author)

Design procedure for a wind-wheel with self-adjusting blade mechanism

Directory of Open Access Journals (Sweden)

Gennady A. Oborsky

2014-12-01

Full Text Available Developed is a wind-wheel design equipped with the self-adjusting blade. The blade is positioned eccentrically to the balance wheel and can freely rotate around its axis. Elaborated is the method of calculating the energy characteristics for a wind-wheel with the self-adjusting blade, considering not only the wind force but the force of air counter flow resistance to the blade’s rotation. Initially, the blade being located at an angle α = 45 to the wheel rotation plane, the air flow rotates the wheel with the maximum force. Thus, the speed of rotation increases that involves the increase in air counter flow resistance and results in blade turning with respective angle α reduction. This, consequently, reduces the torque. When the torsional force and the resistance enter into equilibrium, the blade takes a certain angle α, and the wheel speed becomes constant. This wind-wheel design including a self-adjusting blade allows increasing the air flow load ratio when compared to the wind-wheel equipped with a jammed blade.

The central uplift of Ritchey crater, Mars

Science.gov (United States)

Ding, Ning; Bray, Veronica J.; McEwen, Alfred S.; Mattson, Sarah S.; Okubo, Chris H.; Chojnacki, Matthew; Tornabene, Livio L.

2015-01-01

Ritchey crater is a ∼79 km diameter complex crater near the boundary between Hesperian ridged plains and Noachian highland terrain on Mars (28.8°S, 309.0°E) that formed after the Noachian. High Resolution Imaging Science Experiment (HiRISE) images of the central peak reveal fractured massive bedrock and megabreccia with large clasts. Compact Reconnaissance Imaging Spectrometer for Mars (CRISM) spectral analysis reveals low calcium pyroxene (LCP), olivine (OL), hydrated silicates (phyllosilicates) and a possible identification of plagioclase bedrock. We mapped the Ritchey crater central uplift into ten units, with 4 main groups from oldest and originally deepest to youngest: (1) megabreccia with large clasts rich in LCP and OL, and with alteration to phyllosilicates; (2) massive bedrock with bright and dark regions rich in LCP or OL, respectively; (3) LCP and OL-rich impactites draped over the central uplift; and (4) aeolian deposits. We interpret the primitive martian crust as igneous rocks rich in LCP, OL, and probably plagioclase, as previously observed in eastern Valles Marineris. We do not observe high-calcium pyroxene (HCP) rich bedrock as seen in Argyre or western Valles Marineris. The association of phyllosilicates with deep megabreccia could be from impact-induced alteration, either as a result of the Richey impact, or alteration of pre-existing impactites from Argyre basin and other large impacts that preceded the Ritchey impact, or both.

The central uplift of Ritchey crater, Mars

Science.gov (United States)

Ding, Ning; Bray, Veronica J.; McEwen, Alfred S.; Mattson, Sarah S.; Okubo, Chris H.; Chojnacki, Matthew; Tornabene, Livio L.

2015-05-01

Ritchey crater is a ∼79 km diameter complex crater near the boundary between Hesperian ridged plains and Noachian highland terrain on Mars (28.8°S, 309.0°E) that formed after the Noachian. High Resolution Imaging Science Experiment (HiRISE) images of the central peak reveal fractured massive bedrock and megabreccia with large clasts. Compact Reconnaissance Imaging Spectrometer for Mars (CRISM) spectral analysis reveals low calcium pyroxene (LCP), olivine (OL), hydrated silicates (phyllosilicates) and a possible identification of plagioclase bedrock. We mapped the Ritchey crater central uplift into ten units, with 4 main groups from oldest and originally deepest to youngest: (1) megabreccia with large clasts rich in LCP and OL, and with alteration to phyllosilicates; (2) massive bedrock with bright and dark regions rich in LCP or OL, respectively; (3) LCP and OL-rich impactites draped over the central uplift; and (4) aeolian deposits. We interpret the primitive martian crust as igneous rocks rich in LCP, OL, and probably plagioclase, as previously observed in eastern Valles Marineris. We do not observe high-calcium pyroxene (HCP) rich bedrock as seen in Argyre or western Valles Marineris. The association of phyllosilicates with deep megabreccia could be from impact-induced alteration, either as a result of the Richey impact, or alteration of pre-existing impactites from Argyre basin and other large impacts that preceded the Ritchey impact, or both.

Phased uplift of the northeastern Tibetan Plateau inferred from a pollen record from Yinchuan Basin, northwestern China.

Science.gov (United States)

Li, Xinling; Hao, Qingzhen; Wei, Mingjian; Andreev, Andrei A; Wang, Junping; Tian, Yanyan; Li, Xiaolei; Cai, Maotang; Hu, Jianmin; Shi, Wei

2017-12-21

The uplift of the Tibetan Plateau (TP) significantly affected both regional and global climates. Although there is evidence that the Tibetan Plateau experienced uplift during the Quaternary, the timing and amplitude are poorly constrained. However, the increased availability of long sedimentary records of vegetation change provides an opportunity to reconstruct the timing of the uplift. Here, we present a well-dated, high-resolution pollen record for the last 2.6 Ma from the Yinchuan Basin, which was incised by the Yellow River with its source in the northeastern Tibetan Plateau. Variations in the Artemisia/Chenopodiaceae (A/C) ratio of the reveal changes in moisture conditions in the Yinchuan Basin during glacial-interglacial cycles, as well as a gradual long-term aridification trend which is consistent with progressive global cooling. However, fluctuations in the percentages of Picea and Abies differ from those of the A/C ratio and we propose that they reflect changes in the vegetation and environment of high elevation areas. The Picea and Abies records reveal two phases of increased representation, at 2.1 and 1.2 Ma, which may indicate phases in the uplift of the northeastern Tibetan Plateau. Thus, they provide independent evidence for the timing of the uplift of the Tibetan Plateau during the Quaternary.

Ponderomotive Forces in Cosmos

Science.gov (United States)

Lundin, R.; Guglielmi, A.

2006-12-01

This review is devoted to ponderomotive forces and their importance for the acceleration of charged particles by electromagnetic waves in space plasmas. Ponderomotive forces constitute time-averaged nonlinear forces acting on a media in the presence of oscillating electromagnetic fields. Ponderomotive forces represent a useful analytical tool to describe plasma acceleration. Oscillating electromagnetic fields are also related with dissipative processes, such as heating of particles. Dissipative processes are, however, left outside these discussions. The focus will be entirely on the (conservative) ponderomotive forces acting in space plasmas. The review consists of seven sections. In Section 1, we explain the rational for using the auxiliary ponderomotive forces instead of the fundamental Lorentz force for the study of particle motions in oscillating fields. In Section 2, we present the Abraham, Miller, Lundin-Hultqvist and Barlow ponderomotive forces, and the Bolotovsky-Serov ponderomotive drift. The hydrodynamic, quasi-hydrodynamic, and ‘`test-particle’' approaches are used for the study of ponderomotive wave-particle interaction. The problems of self-consistency and regularization are discussed in Section 3. The model of static balance of forces (Section 4) exemplifies the interplay between thermal, gravitational and ponderomotive forces, but it also introduces a set of useful definitions, dimensionless parameters, etc. We analyze the Alfvén and ion cyclotron waves in static limit with emphasis on the specific distinction between traveling and standing waves. Particular attention has been given to the impact of traveling Alfvén waves on the steady state anabatic wind that blows over the polar regions (Section~5). We demonstrate the existence of a wave-induced cold anabatic wind. We also show that, at a critical point, the ponderomotive acceleration of the wind is a factor of 3 greater than the thermal acceleration. Section 6 demonstrates various

Colluvial deposits as a possible weathering reservoir in uplifting mountains

Science.gov (United States)

Carretier, Sébastien; Goddéris, Yves; Martinez, Javier; Reich, Martin; Martinod, Pierre

2018-03-01

The role of mountain uplift in the evolution of the global climate over geological times is controversial. At the heart of this debate is the capacity of rapid denudation to drive silicate weathering, which consumes CO2. Here we present the results of a 3-D model that couples erosion and weathering during mountain uplift, in which, for the first time, the weathered material is traced during its stochastic transport from the hillslopes to the mountain outlet. To explore the response of weathering fluxes to progressively cooler and drier climatic conditions, we run model simulations accounting for a decrease in temperature with or without modifications in the rainfall pattern based on a simple orographic model. At this stage, the model does not simulate the deep water circulation, the precipitation of secondary minerals, variations in the pH, below-ground pCO2, and the chemical affinity of the water in contact with minerals. Consequently, the predicted silicate weathering fluxes probably represent a maximum, although the predicted silicate weathering rates are within the range of silicate and total weathering rates estimated from field data. In all cases, the erosion rate increases during mountain uplift, which thins the regolith and produces a hump in the weathering rate evolution. This model thus predicts that the weathering outflux reaches a peak and then falls, consistent with predictions of previous 1-D models. By tracking the pathways of particles, the model can also consider how lateral river erosion drives mass wasting and the temporary storage of colluvial deposits on the valley sides. This reservoir is comprised of fresh material that has a residence time ranging from several years up to several thousand years. During this period, the weathering of colluvium appears to sustain the mountain weathering flux. The relative weathering contribution of colluvium depends on the area covered by regolith on the hillslopes. For mountains sparsely covered by regolith

Improving Energy Security for Air Force Installations

Science.gov (United States)

2015-09-01

equipment, and habitat destruction from general construction (DoE, “ Wind Turbine Interactions with Birds , Bats, and Their Habitats,” pgs 2-4). Another...utility-resource-efficiency>, accessed 16 December 2014. Department of Energy, Wind Turbine Interactions with Birds , Bats, and Their Habitats... Wind power is a mature technology, with wind turbines first being used for electricity in the late 19th century. The Air Force operates two wind

Land uplift and relative sea-level changes in the Loviisa area, southeastern Finland, during the last 8000 years

International Nuclear Information System (INIS)

Miettinen, A.; Eronen, M.; Hyvaerinen, H.

1999-09-01

Southeastern Finland belongs to the area covered by the Weichselian ice sheet, where the release of the ice load caused a rapid isostatic rebound during the postglacial time. While the mean overall apparent uplift is of the order of 2 mm/yr today, in the early Holocene time it was several times higher. A marked decrease in the rebound rate occurred around 8500 BP, however, since then the uplift rate has remained high until today, with a slightly decreasing trend towards the present time. According to current understanding there have neither been temporary increases nor decreases in the rate of uplift during the postglacial time. Even so, it is not known for sure whether there are regional irregularities on the rebound in Finland. Concurrently with land uplift, relative sea-level changes in the Baltic basin were also strongly affected by the global eustatic rise of sea-level. During the early Litorina Sea stage on the southern coast of Finland around 7000 BP, the rise in sea-level exceeded the rate of land uplift, and resulted in a short-lived transgression. The most accurate information on relative sea-level changes in an uplifting area may be obtained from radiocarbon dated events of isolation in small lake basins, as they were cut off from larger bodies of water. The isolations of such basins from the sea may be reliably determined by the recorded changes in the diatom flora in the sediment sequences, at horizons which may be radiometrically dated. In the present study, the isolation-horizons of 13 basins were dated by 26 conventional and 2 AMS radiocarbon dates. According to the available sets of dates, the time span of emergence extends from 8300 BP to the past few hundred years, for lakes from c. 30 m to 1.1 m above the present sea-level. Due to the global rise in sea-level, during the period of 7500-6500 BP, the sea-level rise clearly exceeded the rate of uplift, and resulted in the Litorina transgression, which had an amplitude of around one metre. The

Land uplift and relative sea-level changes in the Loviisa area, southeastern Finland, during the last 8000 years

Energy Technology Data Exchange (ETDEWEB)

Miettinen, A.; Eronen, M.; Hyvaerinen, H. [Helsinki Univ. (Finland). Dept. of Geology

1999-09-01

Southeastern Finland belongs to the area covered by the Weichselian ice sheet, where the release of the ice load caused a rapid isostatic rebound during the postglacial time. While the mean overall apparent uplift is of the order of 2 mm/yr today, in the early Holocene time it was several times higher. A marked decrease in the rebound rate occurred around 8500 BP, however, since then the uplift rate has remained high until today, with a slightly decreasing trend towards the present time. According to current understanding there have neither been temporary increases nor decreases in the rate of uplift during the postglacial time. Even so, it is not known for sure whether there are regional irregularities on the rebound in Finland. Concurrently with land uplift, relative sea-level changes in the Baltic basin were also strongly affected by the global eustatic rise of sea-level. During the early Litorina Sea stage on the southern coast of Finland around 7000 BP, the rise in sea-level exceeded the rate of land uplift, and resulted in a short-lived transgression. The most accurate information on relative sea-level changes in an uplifting area may be obtained from radiocarbon dated events of isolation in small lake basins, as they were cut off from larger bodies of water. The isolations of such basins from the sea may be reliably determined by the recorded changes in the diatom flora in the sediment sequences, at horizons which may be radiometrically dated. In the present study, the isolation-horizons of 13 basins were dated by 26 conventional and 2 AMS radiocarbon dates. According to the available sets of dates, the time span of emergence extends from 8300 BP to the past few hundred years, for lakes from c. 30 m to 1.1 m above the present sea-level. Due to the global rise in sea-level, during the period of 7500-6500 BP, the sea-level rise clearly exceeded the rate of uplift, and resulted in the Litorina transgression, which had an amplitude of around one metre. The

Emissions and temperature benefits: The role of wind power in China.

Science.gov (United States)

Duan, Hongbo

2017-01-01

As a non-fossil technology, wind power has an enormous advantage over coal because of its role in climate change mitigation. Therefore, it is important to investigate how substituting wind power for coal-fired electricity will affect emission reductions, changes in radiative forcing and rising temperatures, particularly in the context of emission limits. We developed an integrated methodology that includes two parts: an energy-economy-environmental (3E) integrated model and an emission-temperature response model. The former is used to simulate the dynamic relationships between economic output, wind energy and greenhouse gas (GHG) emissions; the latter is used to evaluate changes in radiative forcing and warming. Under the present development projection, wind energy cannot serve as a major force in curbing emissions, even under the strictest space-restraining scenario. China's temperature contribution to global warming will be up to 21.76% if warming is limited to 2 degrees. With the wind-for-coal power substitution, the corresponding contribution to global radiative forcing increase and temperature rise will decrease by up to 10% and 6.57%, respectively. Substituting wind power for coal-fired electricity has positive effects on emission reductions and warming control. However, wind energy alone is insufficient for climate change mitigation. It forms an important component of the renewable energy portfolio used to combat global warming. Copyright © 2016 Elsevier Inc. All rights reserved.

Terreneuvian stratigraphy and faunas from the Anabar Uplift, Siberia

Directory of Open Access Journals (Sweden)

Artem Kouchinsky

2017-06-01

Full Text Available Assemblages of mineralized skeletal fossils are described from limestone rocks of the lower Cambrian Nemakit-Daldyn, Medvezhya, Kugda-Yuryakh, Manykay, and lower Emyaksin formations exposed on the western and eastern flanks of the Anabar Uplift of the northern Siberian Platform. The skeletal fossil assemblages consist mainly of anabaritids, molluscs, and hyoliths, and also contain other taxa such as Blastulospongia, Chancelloria, Fomitchella, Hyolithellus, Platysolenites, Protohertzina, and Tianzhushanella. The first tianzhushanellids from Siberia, including Tianzhushanella tolli sp. nov., are described. The morphological variation of Protohertzina anabarica and Anabarites trisulcatus from their type locality is documented. Prominent longitudinal keels in the anabaritid Selindeochrea tripartita are demonstrated. Among the earliest molluscs from the Nemakit-Daldyn Formation, Purella and Yunnanopleura are interpreted as shelly parts of the same species. Fibrous microstructure of the outer layer and a wrinkled inner layer of mineralised cuticle in the organophosphatic sclerites of Fomitchella are reported. A siliceous composition of the globular fossil Blastulospongia is reported herein and a possible protistan affinity similar to Platysolenites is discussed. New carbon isotope data facilitate correlation both across the Anabar Uplift and with the Terreneuvian Series of the IUGS chronostratigraphical scheme for the Cambrian System. The base of Cambrian Stage 2 is provisionally placed herein within the Fortunian‒Cambrian Stage 2 transitional interval bracketed by the lowest appearance of Watsonella crosbyi and by a slightly higher horizon at the peak of carbon isotope excursion Iʹ from western flank of the Anabar Uplift. Correlation across the Siberian Platform of the fossiliferous Medvezhya and lower Emyaksin formations showing δ13Ccarb excursion Iʹ with the upper Sukharikha Formation containing excursion 5p and upper Ust’-Yudoma Formation

Development of Seismic Demand for Chang-Bin Offshore Wind Farm in Taiwan Strait

Directory of Open Access Journals (Sweden)

Yu-Kai Wang

2016-12-01

Full Text Available Taiwan is located on the Pacific seismic belt, and the soil conditions of Taiwan’s offshore wind farms are softer than those in Europe. To ensure safety and stability of the offshore wind turbine supporting structures, it is important to assess the offshore wind farms seismic forces reasonably. In this paper, the relevant seismic and geological data are obtained for Chang-Bin offshore wind farm in Taiwan Strait, the probabilistic seismic hazard analysis (PSHA is carried out, and the first uniform hazard response spectrum for Chang-Bin offshore wind farm is achieved. Compared with existing design response spectrum in the local regulation, this site-specific seismic hazard analysis has influence on the seismic force considered in the design of supporting structures and therefore affects the cost of the supporting structures. The results show that a site-specific seismic hazard analysis is required for high seismic area. The paper highlights the importance of seismic hazard analysis to assess the offshore wind farms seismic forces. The follow-up recommendations and research directions are given for Taiwan’s offshore wind turbine supporting structures under seismic force considerations.

Alpine glacial topography and the rate of rock column uplift

DEFF Research Database (Denmark)

Pedersen, Vivi Kathrine; Egholm, D.L.; Nielsen, S.B.

2010-01-01

The present study investigates the influence of alpine glacial erosion on the morphology and relief distribution of mountain regions associated with varying rock column uplift rates. We take a global approach and analyse the surface area distribution of all mountain regions affected by glacial er...

Review of Bothnian Sea shore-level displacement data and use of a GIS tool to estimate isostatic uplift

International Nuclear Information System (INIS)

Vuorela, A.; Penttinen, T.; Lahdenperae, A.-M.

2009-02-01

The aim and approach of the study were to produce source data estimates necessary for modelling the future biosphere. The study updated the list of 14 C datings of sea-level index points, which show when lakes and mires were isolated from the Baltic Sea due to isostatic uplift. The study concentrated on the Bothnian Sea, especially the Olkiluoto area. The older Finnish datings (a list of 260 sea-level index points determined in 1995) were checked and revised as needed. New data was available for 56 Finnish and 41 Swedish index points. State-of-the-art 14 C calibration methods were applied. Various available data were used to estimate the parameters of the glacio-isostatic uplift model's slow component. The component describes the uplift in relation to time using parameters B s , which is related to the uplift's total duration, and A s , which is half of the total uplift possible in the period lasting from the Last Glacial Maximum to the distant future. The B s values were estimated by means of 1) crustal thickness and 2) shoreline displacement curves. In applying method 1, this study revised the function describing the relationship between crustal thickness and B s and created a new derivative-based method that also estimates the parameter A s without radiocarbon datings and using only crustal thickness and current uplift maps. In method 2, sea-level index point subsets along the Finnish and Swedish coasts of the Bothnian Sea were selected from the revised database, and their datings and elevations were used to determine the corresponding land uplift parameters. The parameter value distributions were used to produce maps. The values of the inertia factor B s are on average 6% higher than those calculated in 2001 but they are 10% lower in the Olkiluoto region. According to the interpolations of the new and old data, the estimated uplift at Olkiluoto for AD 12000 is 2.8 m (7%) less than calculated previously. The derivative-based method predicts an uplift for AD

A ``Cyber Wind Facility'' for HPC Wind Turbine Field Experiments

Science.gov (United States)

Brasseur, James; Paterson, Eric; Schmitz, Sven; Campbell, Robert; Vijayakumar, Ganesh; Lavely, Adam; Jayaraman, Balaji; Nandi, Tarak; Jha, Pankaj; Dunbar, Alex; Motta-Mena, Javier; Craven, Brent; Haupt, Sue

2013-03-01

The Penn State ``Cyber Wind Facility'' (CWF) is a high-fidelity multi-scale high performance computing (HPC) environment in which ``cyber field experiments'' are designed and ``cyber data'' collected from wind turbines operating within the atmospheric boundary layer (ABL) environment. Conceptually the ``facility'' is akin to a high-tech wind tunnel with controlled physical environment, but unlike a wind tunnel it replicates commercial-scale wind turbines operating in the field and forced by true atmospheric turbulence with controlled stability state. The CWF is created from state-of-the-art high-accuracy technology geometry and grid design and numerical methods, and with high-resolution simulation strategies that blend unsteady RANS near the surface with high fidelity large-eddy simulation (LES) in separated boundary layer, blade and rotor wake regions, embedded within high-resolution LES of the ABL. CWF experiments complement physical field facility experiments that can capture wider ranges of meteorological events, but with minimal control over the environment and with very small numbers of sensors at low spatial resolution. I shall report on the first CWF experiments aimed at dynamical interactions between ABL turbulence and space-time wind turbine loadings. Supported by DOE and NSF.

Tool for Forecasting Cool-Season Peak Winds Across Kennedy Space Center and Cape Canaveral Air Force Station

Science.gov (United States)

Barrett, Joe H., III; Roeder, William P.

2010-01-01

The expected peak wind speed for the day is an important element in the daily morning forecast for ground and space launch operations at Kennedy Space Center (KSC) and Cape Canaveral Air Force Station (CCAFS). The 45th Weather Squadron (45 WS) must issue forecast advisories for KSC/CCAFS when they expect peak gusts for >= 25, >= 35, and >= 50 kt thresholds at any level from the surface to 300 ft. In Phase I of this task, the 45 WS tasked the Applied Meteorology Unit (AMU) to develop a cool-season (October - April) tool to help forecast the non-convective peak wind from the surface to 300 ft at KSC/CCAFS. During the warm season, these wind speeds are rarely exceeded except during convective winds or under the influence of tropical cyclones, for which other techniques are already in use. The tool used single and multiple linear regression equations to predict the peak wind from the morning sounding. The forecaster manually entered several observed sounding parameters into a Microsoft Excel graphical user interface (GUI), and then the tool displayed the forecast peak wind speed, average wind speed at the time of the peak wind, the timing of the peak wind and the probability the peak wind will meet or exceed 35, 50 and 60 kt. The 45 WS customers later dropped the requirement for >= 60 kt wind warnings. During Phase II of this task, the AMU expanded the period of record (POR) by six years to increase the number of observations used to create the forecast equations. A large number of possible predictors were evaluated from archived soundings, including inversion depth and strength, low-level wind shear, mixing height, temperature lapse rate and winds from the surface to 3000 ft. Each day in the POR was stratified in a number of ways, such as by low-level wind direction, synoptic weather pattern, precipitation and Bulk Richardson number. The most accurate Phase II equations were then selected for an independent verification. The Phase I and II forecast methods were

Alternative Energy Sources for United States Air Force Installations

Science.gov (United States)

1975-08-01

applications were developed for the vertical- axis rotor, the concept never became popular. Interest was renewed in the Darrieus type wind turbine when the...chordwise lift force is greater than the chorcwise drag force (ref. 30). The Darrieus wind turbine offers the follwing advantages relative to the more...Laboratories, New Mexico, May 1974. 105 lAFWL-TR-75- 193 REFERENCES (Cont’d) 32. Banas, J. F., et al., Application of Darrieus Vertical - Axis Wind Turbine to

Wind power engine

Energy Technology Data Exchange (ETDEWEB)

Musgrove, P J

1977-02-10

The device is a wind-power engine with vertical axis and with one or several wings with airfoil profile fixed on a frame which is pivoted at the vertical axis. Each wing forms at least on one part of its length an angle of inclination with the vertical. The angle increases under the influence of the centrifugal force when the r.p.m. exceed a normal operation range. This method helps to reduce mechanical loads occurring with high wind speeds without requiring a complicated construction.

Turbulence Simulation of Laboratory Wind-Wave Interaction in High Winds and Upscaling to Ocean Conditions

Science.gov (United States)

2016-12-22

Oceanogr., 46, 1377-1397 Cebeci, T. & P. Bradshaw, 1988: physical and computational aspects of convective heat transfer , Springer-Verlag, p.487...on surface properties and flow separation. Strongly-forced wind seas are characterized by enhanced group modulation , as significant additional...energy flux from the wind augments the hydrodynamic modulations . Using compact steep chirped wave packets, we investigated for the first time the

Efficiency of lung ventilation for people performing wind instruments.

Science.gov (United States)

Brzęk, Anna; Famuła, Anna; Kowalczyk, Anna; Plinta, Ryszard

Wind instruments musicians are particularly prone to excessive respiratory efforts. Prolonged wind instruments performing may lead to changes in respiratory tracts and thus to respiratory muscles overload. It may result in decreasing lung tissue pliability and, as a consequence, in emphysema. Aim of the research has been to describe basic spirometric parameters for wind players and causes of potential changes. Slow and forced spirometry with the use of Micro Lab Viasys (Micro Medical, Great Britain) was conducted on 31 wind musicians (group A). A survey concerning playing time and frequency, weight of instruments, and education on diaphragmatic breathing was conducted. The control group included 34 healthy persons at similar age (group B). The results were statistically described using Excel and Statistica programmes. The respiratory parameters were within the range of physiological norms and forced expiratory volume in 1 s to forced vital capacity (FEV1/FVC) exceeded in both groups the values of 100%. Forced vital capacity and expiratory vital capacity (EVC) values were significantly lower in the group of musicians than in the control group (p wind instrument. Spirometric parameters relative to standards may prove a good respiratory capacity. Peak expiratory flow (PEF) and FEV1 may indicate that a proper technique of respiration during performance was acquired. The length of time when performing wind instrument may influence parameters of dynamic spirometry. Med Pr 2016;67(4):427-433. This work is available in Open Access model and licensed under a CC BY-NC 3.0 PL license.

Maneuverability of Ships with small Draught in Steady Wind

Directory of Open Access Journals (Sweden)

Daeng Paroka

2016-04-01

Full Text Available Wind force and moment may force a ship to drastically decrease its speed and use a large drift angle as well as a large rudder angle in order to maintain its course. Shipswith a small draught might have more risk in maneuvering to its point of view compared with a ship with a larger draught. This paper discusses maneuverability of a ship with a small draught in steady wind. The effect of wind on ship speed, drift angle, and rudder angle are investigated in a steady state condition. Five different ratios of wind velocity to ship speed from 1.0 to 20.0 are used in the simulation. The variation in wind direction is examined from 0°to 180°. Results of the numerical simulation show that thewind has a significant effect on the reduction in ship speed with a wind direction less than 100°. The drift angle increases due to increasing wind velocity in the same wind direction. Wind direction also has a significant effect on the drift angle especially when the wind direction is less than 140°. The same phenomenon was found for the rudder angle. The necessary rudder angle is greater than the maximum rudder angle of the ship when the wind direction is 60°with a wind velocity to ship speed ratio of 20 or more.

Icing Problems of Wind Turbine Blades in Cold Climates

DEFF Research Database (Denmark)

Hudecz, Adriána

Climatic Wind Tunnel located at FORCE Technology. The aerodynamic forces acting on the blade during ice accretion for different angles of attack at various air temperatures were measured along with the mass of ice and the final ice shape. For all three types of ice accretion, glaze, mixed and rime ice...... and on the aerodynamic characteristics of the airfoil. The trend of the reduction of lift coefficients agrees quite well with the wind tunnel test results, although based on the measured and the numerical lift coefficients of the clean airfoil, the presence of the wind tunnel walls had significant influence...

Uplift-driven diversification in the Hengduan Mountains, a temperate biodiversity hotspot.

Science.gov (United States)

Xing, Yaowu; Ree, Richard H

2017-04-25

A common hypothesis for the rich biodiversity found in mountains is uplift-driven diversification-that orogeny creates conditions favoring rapid in situ speciation of resident lineages. We tested this hypothesis in the context of the Qinghai-Tibetan Plateau (QTP) and adjoining mountain ranges, using the phylogenetic and geographic histories of multiple groups of plants to infer the tempo (rate) and mode (colonization versus in situ diversification) of biotic assembly through time and across regions. We focused on the Hengduan Mountains region, which in comparison with the QTP and Himalayas was uplifted more recently (since the late Miocene) and is smaller in area and richer in species. Time-calibrated phylogenetic analyses show that about 8 million y ago the rate of in situ diversification increased in the Hengduan Mountains, significantly exceeding that in the geologically older QTP and Himalayas. By contrast, in the QTP and Himalayas during the same period the rate of in situ diversification remained relatively flat, with colonization dominating lineage accumulation. The Hengduan Mountains flora was thus assembled disproportionately by recent in situ diversification, temporally congruent with independent estimates of orogeny. This study shows quantitative evidence for uplift-driven diversification in this region, and more generally, tests the hypothesis by comparing the rate and mode of biotic assembly jointly across time and space. It thus complements the more prevalent method of examining endemic radiations individually and could be used as a template to augment such studies in other biodiversity hotspots.

Wind load modeling for topology optimization of continuum structures

NARCIS (Netherlands)

Zakhama, R.; Abdalla, M.M.; Gürdal, Z.; Smaoui, H.

2010-01-01

Topology optimization of two and three dimensional structures subject to dead and wind loading is considered. The wind loading is introduced into the formulation by using standard expressions for the drag force, and a strategy is devised so that wind pressure is ignored where there is no surface

Aerodynamic force coefficients of plain bridge cables in wet conditions

DEFF Research Database (Denmark)

Matteoni, Giulia; Georgakis, Christos T.

In this paper, the aerodynamic forces and force coefficients from preliminary static wind tunnel tests on a plain cable in wet conditions are presented. The presented results are for several different relative cable wind-angles. A comparison is made with tests in dry conditions. In dry conditions...

Seismic influence in the Quaternary uplift of the Central Chile coastal margin, preliminary results.

Science.gov (United States)

Valdivia, D.; del Valle, F.; Marquardt, C.; Elgueta, S.

2017-12-01

In order to quantify the influence of NW striking potentially seismogenic normal faults over the longitudinal variation of the Central Chile Coastal margin uplift, we measured Quaternary marine terraces, which represent the tectonic uplift of the coastal margin. Movement in margin oblique normal faults occurs by co-seismic extension of major subduction earthquakes and has occurred in the Pichilemu fault, generating a 7.0 Mw earthquake after the 2010 8.8 Mw Maule earthquake.The coastal area between 32° and 34° S was selected due to the presence of a well-preserved sequence of 2 to 5 Quaternary marine terraces. In particular, the margin oblique normal NW-trending, SW-dipping Laguna Verde fault, south of Valparaiso (33° S) puts in contact contrasting morphologies: to the south, a flat coast with wide marine terraces is carved in both, Jurassic plutonic rocks and Neogene semi-consolidated marine sediments; to the north, a steeper scarp with narrower marine terraces, over 120 m above the corresponding ones in the southern coast, is carved in Jurassic plutonic rocks.We have collected over 6 months microseimic data, providing information on seismic activity and underground geometry of the Laguna Verde fault. We collected ca. 100 systematic measurements of fringes at the base of paleo coastal scarps through field mapping and a 5 m digital elevation model. These fringes mark the maximum sea level during the terrace's carving.The heights of these fringes range between 0 and 250 masl. We estimate a 0.7 mm/yr slip rate for the Laguna Verde fault based on the height difference between corresponding terraces north- and southward, with an average uplift rate of 0.3 mm/yr for the whole area.NW striking normal faults, besides representing a potential seismic threat to the near population on one of the most densely populated areas of Chile, heavily controls the spatial variation of the coastal margin uplift. In Laguna Verde, the uplift rate differs more than three times northward

Hywind floating wind turbine project

Energy Technology Data Exchange (ETDEWEB)

Crome, Tim

2010-07-01

The Hywind floating wind turbine concept was developed by StatoilHydro. Technip was awarded the contract for engineering, fabrication and installation of a demonstration unit in May 2008 and the completed wind turbine was installed mid June 2009 at the west coast of Norway on 220 m water depth. The demonstration unit will generate 2,3 MW and is equipped with instrumentation for monitoring mooring forces, strains and motions. The fabrication of the SPAR type steel substructure was performed at Technip Offshore Finland facilities in Pori and was towed horizontally from Finland to Norway, where it was upended to a vertical position by water filling. The completed floating wind turbine was towed vertically to the final location west of Karmoey and connected to the pre-installed three legged anchor system using an Anchor Handling Tug type vessel. The wind turbine test period is scheduled to start in September 2009. Statoil will monitor the performance of the system for two years before decision will be taken for further development. The paper will present the main challenges and lessons learned through design, fabrication and installation of this first of its kind structure. Main emphasis will be on the special challenges experienced for this floating, catenary moored, slender unit which is highly exposed for wind induced forces in addition to current and waves in hostile North Sea environments. (Author)

The role of tectonic uplift, climate, and vegetation in the long-term terrestrial phosphorous cycle

Directory of Open Access Journals (Sweden)

C. Buendía

2010-06-01

Full Text Available Phosphorus (P is a crucial element for life and therefore for maintaining ecosystem productivity. Its local availability to the terrestrial biosphere results from the interaction between climate, tectonic uplift, atmospheric transport, and biotic cycling. Here we present a mathematical model that describes the terrestrial P-cycle in a simple but comprehensive way. The resulting dynamical system can be solved analytically for steady-state conditions, allowing us to test the sensitivity of the P-availability to the key parameters and processes. Given constant inputs, we find that humid ecosystems exhibit lower P availability due to higher runoff and losses, and that tectonic uplift is a fundamental constraint. In particular, we find that in humid ecosystems the biotic cycling seem essential to maintain long-term P-availability. The time-dependent P dynamics for the Franz Josef and Hawaii chronosequences show how tectonic uplift is an important constraint on ecosystem productivity, while hydroclimatic conditions control the P-losses and speed towards steady-state. The model also helps describe how, with limited uplift and atmospheric input, as in the case of the Amazon Basin, ecosystems must rely on mechanisms that enhance P-availability and retention. Our novel model has a limited number of parameters and can be easily integrated into global climate models to provide a representation of the response of the terrestrial biosphere to global change.

Analysis of experimental data: The average shape of extreme wave forces on monopile foundations and the NewForce model

DEFF Research Database (Denmark)

Schløer, Signe; Bredmose, Henrik; Ghadirian, Amin

2017-01-01

Experiments with a stiff pile subjected to extreme wave forces typical of offshore wind farm storm conditions are considered. The exceedance probability curves of the nondimensional force peaks and crest heights are analysed. The average force time history normalised with their peak values are co...... to the average shapes. For more nonlinear wave shapes, higher order terms has to be considered in order for the NewForce model to be able to predict the expected shapes.......Experiments with a stiff pile subjected to extreme wave forces typical of offshore wind farm storm conditions are considered. The exceedance probability curves of the nondimensional force peaks and crest heights are analysed. The average force time history normalised with their peak values...... are compared across the sea states. It is found that the force shapes show a clear similarity when grouped after the values of the normalised peak force, F/(ρghR2), normalised depth h/(gT2p) and presented in a normalised time scale t/Ta. For the largest force events, slamming can be seen as a distinct ‘hat...

Colluvial deposits as a possible weathering reservoir in uplifting mountains

Directory of Open Access Journals (Sweden)

S. Carretier

2018-03-01

Full Text Available The role of mountain uplift in the evolution of the global climate over geological times is controversial. At the heart of this debate is the capacity of rapid denudation to drive silicate weathering, which consumes CO2. Here we present the results of a 3-D model that couples erosion and weathering during mountain uplift, in which, for the first time, the weathered material is traced during its stochastic transport from the hillslopes to the mountain outlet. To explore the response of weathering fluxes to progressively cooler and drier climatic conditions, we run model simulations accounting for a decrease in temperature with or without modifications in the rainfall pattern based on a simple orographic model. At this stage, the model does not simulate the deep water circulation, the precipitation of secondary minerals, variations in the pH, below-ground pCO2, and the chemical affinity of the water in contact with minerals. Consequently, the predicted silicate weathering fluxes probably represent a maximum, although the predicted silicate weathering rates are within the range of silicate and total weathering rates estimated from field data. In all cases, the erosion rate increases during mountain uplift, which thins the regolith and produces a hump in the weathering rate evolution. This model thus predicts that the weathering outflux reaches a peak and then falls, consistent with predictions of previous 1-D models. By tracking the pathways of particles, the model can also consider how lateral river erosion drives mass wasting and the temporary storage of colluvial deposits on the valley sides. This reservoir is comprised of fresh material that has a residence time ranging from several years up to several thousand years. During this period, the weathering of colluvium appears to sustain the mountain weathering flux. The relative weathering contribution of colluvium depends on the area covered by regolith on the hillslopes. For mountains

A possible cause of the Miocene uplift and volcanism in the central Anatolian plateau

Science.gov (United States)

Bartol, J.; Govers, R. M.; Wortel, M. J.

2010-12-01

During the middle and late Miocene (13-5Ma) several seemingly unrelated events occurred in central Anatolia, Turkey; (1) a new epoch of widespread volcanic activity with a mantle signature, (2) sudden uplift and disruption of a Oligocene-lower Miocene palaeo drainage system in the Western Taurus (southwest Turkey) and (3) a regional regression across southern Turkey (Antalya, Adana, Mut) coeval with volcanic activity. These observations suggest an uplift (>1000 meters) of the central Anatolian plateau by a mechanism which also triggered widespread volcanic activity. In eastern Anatolia, similar events are attributed to delamination of the lithospheric mantle [e.g. Keskin et al., 2003]. Results from tomography [W.Spakman, pers. com]) suggest that the (deeper) Bitlis slab was laterally continuous below the eastern and central Anatolian plateau. We therefore propose that the scenario developed for eastern Anatolian plateau also applies to the central Anatolian plateau. In this scenario, delamination started along the Izmir-Ankara-Erzincan suture zone and was possibly induced by remnants of a northern Neotethys slab or continental collision between Arabia and Eurasia. As the lithospheric mantle separated from the crust it sank into the asthenosphere and was replaced by hot mantle material. If true, delamination is expected to have had a thermal and isostatic imprint. Using a three-dimensional thermal-flexural model and taking changes of the effective elastic thickness due to thermal perturbation into account, we aim to quantify the possible imprints in the geological record of the central and eastern Anatolian plateau. Our model results show that delamination of the lithospheric mantle can explain the present day elevation (1500 m) of the central Anatolian plateau. For the eastern Anatolian plateau, however, delamination of the lithospheric mantle alone can only explain half (1000 m) of the present day elevation. Thickening of the eastern Anatolia crust by 1-5 km (β=1

Rock Uplift above the Yakutat Megathrust on Montague Island, Prince William Sound, Alaska

Science.gov (United States)

Ferguson, K.; Armstrong, P. A.; Haeussler, P. J.; Arkle, J. C.

2011-12-01

The Yakutat microplate is subducting shallowly (~6°) beneath the North American Plate at a rate of approximately 53 mm/yr to the northwest. Deformation from this flat- slab subduction extends >600 km inland and has resulted in regions of focused rock uplift and exhumation in the Alaska Range, central Chugach Mountains, and St. Elias Mountains. Many questions still remain about how strain is partitioned between these regions of focused uplift, particularly in the Prince William Sound (southern Chugach Mountains) on Montague Island. Montague Island (and adjacent Hinchinbrook Island) are ~20 km above the megathrust where there is a large degree of coupling between the subducting Yakutat microplate and overriding North American Plate. Montague Island is of particular interest because it lies between two areas of rapid rock uplift focused in the St. Elias/eastern Chugach Mountains and the western Chugach Mountains. In the St. Elias/eastern Chugach Mountains, faulting related to collisional processes and bending of fault systems causes rapid rock uplift. About 200 km farther northwest in the western Chugach Mountains, recent rock uplift is caused by underplating along the megathrust that is focused within a syntaxial bend of major fault systems and mountain ranges. Montague Island bounds the southern margin of Prince William Sound, and is steep, narrow, and elongate (81 km long and ~15 km wide). The maximum relief is 914 m, making for very steep, mountainous topography considering the narrow width of the island. During the Mw 9.2 earthquake in 1964, the Patton Bay and Hanning Bay reverse faults were reactivated, with 7 and 5 m of vertical offset, respectively. Both faults dip ~60° NW and strike NE-SW parallel to the long-axis of the island and parallel to geomorphic features including lineaments, elongate valleys, and escarpments. Prominent ~450 m high escarpments are present along the SE-facing side of the island, which suggests rapid and sustained uplift. New apatite

Emissions and temperature benefits: The role of wind power in China

Energy Technology Data Exchange (ETDEWEB)

Duan, Hongbo, E-mail: hbduan@ucas.ac.cn

2017-01-15

Background: As a non-fossil technology, wind power has an enormous advantage over coal because of its role in climate change mitigation. Therefore, it is important to investigate how substituting wind power for coal-fired electricity will affect emission reductions, changes in radiative forcing and rising temperatures, particularly in the context of emission limits. Methods: We developed an integrated methodology that includes two parts: an energy-economy-environmental (3E) integrated model and an emission-temperature response model. The former is used to simulate the dynamic relationships between economic output, wind energy and greenhouse gas (GHG) emissions; the latter is used to evaluate changes in radiative forcing and warming. Results: Under the present development projection, wind energy cannot serve as a major force in curbing emissions, even under the strictest space-restraining scenario. China's temperature contribution to global warming will be up to 21.76% if warming is limited to 2 degrees. With the wind-for-coal power substitution, the corresponding contribution to global radiative forcing increase and temperature rise will decrease by up to 10% and 6.57%, respectively. Conclusions: Substituting wind power for coal-fired electricity has positive effects on emission reductions and warming control. However, wind energy alone is insufficient for climate change mitigation. It forms an important component of the renewable energy portfolio used to combat global warming. - Highlights: • We assess the warming benefits associated with substitution of wind power for coal. • The effect of emission space limits on climate responses is deeply examined. • China is responsible for at most 21.76% of global warming given the 2-degree target. • Wind power alone may not be sufficient to face the challenge of climate change. • A fertile policy soil and an aggressive plan are necessary to boost renewables.

Emissions and temperature benefits: The role of wind power in China

International Nuclear Information System (INIS)

Duan, Hongbo

2017-01-01

Background: As a non-fossil technology, wind power has an enormous advantage over coal because of its role in climate change mitigation. Therefore, it is important to investigate how substituting wind power for coal-fired electricity will affect emission reductions, changes in radiative forcing and rising temperatures, particularly in the context of emission limits. Methods: We developed an integrated methodology that includes two parts: an energy-economy-environmental (3E) integrated model and an emission-temperature response model. The former is used to simulate the dynamic relationships between economic output, wind energy and greenhouse gas (GHG) emissions; the latter is used to evaluate changes in radiative forcing and warming. Results: Under the present development projection, wind energy cannot serve as a major force in curbing emissions, even under the strictest space-restraining scenario. China's temperature contribution to global warming will be up to 21.76% if warming is limited to 2 degrees. With the wind-for-coal power substitution, the corresponding contribution to global radiative forcing increase and temperature rise will decrease by up to 10% and 6.57%, respectively. Conclusions: Substituting wind power for coal-fired electricity has positive effects on emission reductions and warming control. However, wind energy alone is insufficient for climate change mitigation. It forms an important component of the renewable energy portfolio used to combat global warming. - Highlights: • We assess the warming benefits associated with substitution of wind power for coal. • The effect of emission space limits on climate responses is deeply examined. • China is responsible for at most 21.76% of global warming given the 2-degree target. • Wind power alone may not be sufficient to face the challenge of climate change. • A fertile policy soil and an aggressive plan are necessary to boost renewables.

Self-starting aerodynamics analysis of vertical axis wind turbine

OpenAIRE

Jianyang Zhu; Hailin Huang; Hao Shen

2015-01-01

Vertical axis wind turbine is a special type of wind-force electric generator which is capable of working in the complicated wind environment. The self-starting aerodynamics is one of the most important considerations for this kind of turbine. This article aims at providing a systematic synthesis on the self-starting aerodynamic characteristics of vertical axis wind turbine based on the numerical analysis approach. First, the physical model of vertical axis wind turbine and its parameter defi...

From ocean depths to mountain tops: uplift of the Troodos Massif (Cyprus) constrained by (U-Th)/He thermochronology and geomorphic analysis

Science.gov (United States)

Morag, N.; Haviv, I.; Katzir, Y.

2013-12-01

The Troodos Massif of Cyprus, rising to nearly 2000 meters above sea level, encompasses one of the world's classic ophiolites. Following its formation at a seafloor spreading center in Late Cretaceous times, this slice of the NeoTethyan oceanic lithosphere was uplifted and eventually exposed on mountain tops during the Neogene. The final uplift and exhumation of the Troodos was previously assigned to Pleistocene age by observations in the circum-Troodos sedimentary strata. However, quantitative thermochronological and geomorphological data from the Massif itself were not available. Here we use apatite (U-Th)/He low-temperature thermochronology complemented by zircon (U-Th)/He and apatite fission track data, and combined with geomorphic analysis to constrain the exhumation and uplift history of the Troodos ophiolite. Apatite (U-Th)/He ages vary with depth from ~ 22 Ma at the top of the Gabbro sequence to ~ 6 Ma at the bottom of the sequence. The deepest sample from a Gabbro pegmatitic dyke intruding the ultramafic sequence yielded an age of ~ 3 Ma. Thermal modeling of apatite (U-Th)/He and fission track data delineates Plio - Pleistocene initiation of rapid uplift and exhumation of the Troodos ophiolite. The estimated cumulative exhumation since its initiation is 2-3 km. No evidence was found for significant uplift of the central Troodos area prior to that time. The geomorphic analysis delineates a bull's-eye zone at the center of the Troodos Massif, where local relief and channel steepness index are highest. The boundaries of this zone roughly correspond with the Mt. Olympus mantle outcrop and suggest recent, differential uplift of this zone relative to its surroundings. The most likely mechanism, which could drive such a focused bull's-eye uplift pattern is hydration of ultramafic rocks (serpentinization) leading to a decrease in rock density and subsequent diapiric uplift of the serpentinized lithospheric mantle.

The winterstorm ``Vivian'' of 27 February 1990: About the meteorological development, wind forces and damage situation in the forests of Switzerland

Science.gov (United States)

Schüepp, M.; Schiesser, H. H.; Huntrieser, H.; Scherrer, H. U.; Schmidtke, H.

1994-09-01

During the months January and February 1990 a series of severe cyclones were responsible for enormous wind-induced damage in Europe. The final of this series, on 27 February 1990, cyclone “Vivian” mainly affected the alpine valleys of Switzerland. 5 Millions m3 of timber were felled by the severe winds, a record number in this century. A complete damage survey of the deforested areas offers in combination with meteorological data an unique data set for a detailed case study of this extreme event. This paper describes the general meteorological development from the synoptic scale down to the mesoscale of Switzerland and presents a general overview of the damage situation. The main results show that a rare situation of a straight frontal zone stretching over the whole Atlantic Ocean and showing a strong gradient in temperature pointed directly toward Central-Europe. Two waves formed along this elongated polar front and deepend rapidly to depressions. The first low travelled on the southernmost trajectory of the whole storm series and affected Switzerland most. North of the Alps the prefrontal warm air was blocked to the east by the arriving coldfront and had to escape into the complex terrain of the alpine valleys. There, the stormy winds were strengthened by channelizing and “Föhn” effects. The large temperature gradient between the prefrontal and the incoming air masses induced thunderstorm activity which vortices and downdrafts might have enhanced locally. As a result most of the damaged forested areas were found between 1200 and 1600 m MSL on slopes, which were mainly exposed toward the prevailing NW-winds. A comparison of extreme wind speeds for the period 1978 1992 revealed that this event's extreme high speed of 74.5 m/s, measured at a high elevated pass station in the mountains, was exceptional. For lower elevated stations the wind speeds were high but in the range of other observed extreme values. In addition to the severe wind forces the duration

Surface uplift in the Central Andes driven by growth of the Altiplano Puna Magma Body.

Science.gov (United States)

Perkins, Jonathan P; Ward, Kevin M; de Silva, Shanaka L; Zandt, George; Beck, Susan L; Finnegan, Noah J

2016-10-25

The Altiplano-Puna Magma Body (APMB) in the Central Andes is the largest imaged magma reservoir on Earth, and is located within the second highest orogenic plateau on Earth, the Altiplano-Puna. Although the APMB is a first-order geologic feature similar to the Sierra Nevada batholith, its role in the surface uplift history of the Central Andes remains uncertain. Here we show that a long-wavelength topographic dome overlies the seismically measured extent of the APMB, and gravity data suggest that the uplift is isostatically compensated. Isostatic modelling of the magmatic contribution to dome growth yields melt volumes comparable to those estimated from tomography, and suggests that the APMB growth rate exceeds the peak Cretaceous magmatic flare-up in the Sierran batholith. Our analysis reveals that magmatic addition may provide a contribution to surface uplift on par with lithospheric removal, and illustrates that surface topography may help constrain the magnitude of pluton-scale melt production.

49 CFR 193.2067 - Wind forces.

Science.gov (United States)

2010-10-01

... ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) PIPELINE SAFETY LIQUEFIED NATURAL GAS FACILITIES... confining, structure; and (3) In the case of impounding systems for LNG storage tanks, impact forces and...

Glacial erosion, rock, and peak uplift within the central Transantarctic Mountains

International Nuclear Information System (INIS)

Stern, T.A.; Baxter, A.K.

2002-01-01

About 1500 m of peak elevation can be ascribed to the isostatic response of valley incision within the central Transantarctic Mountains. This estimate, based on a 3D analysis of topography, and on rock uplift history, represents c. 33% of the maximum peak elevation within the Transantarctic Mountains. Input to the calculation includes a previoulsy published estimate for the variation of flexural rigidity across the western margin of East Antarctica, and a lithospheric free-edge at the Transantarctic Mountains Front. The rebound response is a complex function of lithospheric rigidity, wavelength or erosion, and lithospheric boundary conditions. We also calculate a maximum 4000 m of total rebound due to both valley incision and erosion of mountain tops. This represents 60% of the maximum rock uplift inferred for the mountain front on the bases of fission track data and flexure analysis. (author). 34 refs., 5 figs., 3 tabs

Simulation of the Atmospheric Boundary Layer for Wind Energy Applications

Science.gov (United States)

Marjanovic, Nikola

Energy production from wind is an increasingly important component of overall global power generation, and will likely continue to gain an even greater share of electricity production as world governments attempt to mitigate climate change and wind energy production costs decrease. Wind energy generation depends on wind speed, which is greatly influenced by local and synoptic environmental forcings. Synoptic forcing, such as a cold frontal passage, exists on a large spatial scale while local forcing manifests itself on a much smaller scale and could result from topographic effects or land-surface heat fluxes. Synoptic forcing, if strong enough, may suppress the effects of generally weaker local forcing. At the even smaller scale of a wind farm, upstream turbines generate wakes that decrease the wind speed and increase the atmospheric turbulence at the downwind turbines, thereby reducing power production and increasing fatigue loading that may damage turbine components, respectively. Simulation of atmospheric processes that span a considerable range of spatial and temporal scales is essential to improve wind energy forecasting, wind turbine siting, turbine maintenance scheduling, and wind turbine design. Mesoscale atmospheric models predict atmospheric conditions using observed data, for a wide range of meteorological applications across scales from thousands of kilometers to hundreds of meters. Mesoscale models include parameterizations for the major atmospheric physical processes that modulate wind speed and turbulence dynamics, such as cloud evolution and surface-atmosphere interactions. The Weather Research and Forecasting (WRF) model is used in this dissertation to investigate the effects of model parameters on wind energy forecasting. WRF is used for case study simulations at two West Coast North American wind farms, one with simple and one with complex terrain, during both synoptically and locally-driven weather events. The model's performance with different

On the wave forcing of the semi-annual zonal wind oscillation

Science.gov (United States)

Nagpal, O. P.; Raghavarao, R.

1991-01-01

Observational evidence of rather large period waves (23-60 d) in the troposphere/stratosphere, particularly during the winter months, is presented. Wind data collected on a regular basis employing high-altitude balloons and meteorological rockets over the past few years are used. Maximum entropy methods applied to the time series of zonal wind data indicate the presence of 23-60-waves more prominently than shorter-period waves. The waves have substantial amplitudes in the stratosphere and lower mesosphere, often larger than those noted in the troposphere. The mean zonal wind in the troposphere (5-15 km altitude) during December, January, and February exhibits the presence of strong westerlies at latitudes between 8 and 21 deg N.

Aeroservoelasticity of Wind Turbines

DEFF Research Database (Denmark)

Kallesøe, Bjarne Skovmose

2007-01-01

This thesis deals with the fundamental aeroelastic interaction between structural motion, Pitch action and control for a wind turbine blade. As wind turbines become larger, the interaction between pitch action, blade motion, aerodynamic forces, and control become even more important to understand......, and furthermore linear and therefore suitable for control design. The development of the primary aeroelastic blade model is divided into four steps: 1) Nonlinear partial differential equations (PDEs) of structural blade motion are derived together with equations of pitch action and rotor speed; the individual...... to a 2D blade section model, and it can be used instead of this in many applications, giving a transparent connection to a real wind turbine blade. In this work the aeroelastic blade model is used to analyze interaction between pitch action, blade motion and wind speed variations. Furthermore the model...

Wind loads on post-panamax container ship

DEFF Research Database (Denmark)

Andersen, Ingrid Marie Vincent

2013-01-01

An investigation of the influence of the container configuration on the deck of a 9000+ TEU container ship on wind forces has been carried out through a series of wind tunnel tests with a 1:450 scale model. An analysis of earlier studies was used to select a series of appropriate loading conditions...

Gap Winds in a Fjord: Howe Sound, British Columbia.

Science.gov (United States)

Jackson, Peter L.

1993-01-01

Gap, outflow, or Squamish wind, is the cold low level seaward flow of air through fjords which dissect the coastal mountain barrier of northwestern North America. These flows, occurring mainly during winter, can be strong, threatening safety, economic activity and comfort. Howe Sound gap winds were studied using a combination of observations and several types of models. Observations of winds in Howe Sound showed that gap wind strength varied considerably along the channel, across the channel and vertically. Generally, winds increase down the channel, are strongest along the eastern side, and are below 1000 m depth. Observations were unable to answer all questions about gap winds due to data sparseness, particularly in the vertical direction. Therefore, several modelling approaches were used. The modelling began with a complete 3-dimensional quasi-Boussinesq model (CSU RAMS) and ended with the creation and testing of models which are conceptually simpler, and more easily interpreted and manipulated. A gap wind simulation made using RAMS was shown to be mostly successful by statistical evaluation compared to other mesoscale simulations, and by visual inspection of the fields. The RAMS output, which has very high temporal and spatial resolution, provided much additional information about the details of gap flow. In particular, RAMS results suggested a close analogy between gap wind and hydraulic channel flow, with hydraulic features such as supercritical flow and hydraulic jumps apparent. These findings imply gap wind flow could potentially be represented by much simpler models. The simplest possible models containing pressure gradient, advection and friction but not incorporating hydraulic effects, were created, tested, and found lacking. A hydraulic model, which in addition incorporates varying gap wind height and channel geometry, was created and shown to successfully simulate gap winds. Force balance analysis from RAMS and the hydraulic model showed that pressure

Multi-hazard response analysis of a 5MW offshore wind turbine

DEFF Research Database (Denmark)

Katsanos, Evangelos; Sanz, A. Arrospide; Georgakis, Christos T.

2017-01-01

Wind energy has already dominant role on the scene of the clean energy production. Well-promising markets, like China, India, Korea and Latin America are the fields of expansion for new wind turbines mainly installed in offshore environment, where wind, wave and earthquake loads threat...... of the blades, the nacelle, the tower and the monopile was developed with the use of an aeroelastic code considering the interaction between the elastic and inertial forces, developed in the structure, as well as the generated aerodynamic and hydrodynamic forces. Based on the analysis results, the dynamic...

Windy Prospects: An approach to strategic foresight in the global wind turbine industry

OpenAIRE

Wied, Morten

2007-01-01

This report explores the forces of change which will influence the competitive environment of the wind turbine industry over the coming decade. It further explores the strategic consequences of such change for wind turbine manufacturers and investigates possibilities for adaptation, pre-emption and early warning. This report explores the forces of change which will influence the competitive environment of the wind turbine industry over the coming decade. It further explores the strategic c...

Accidental inflation from Kaehler uplifting

International Nuclear Information System (INIS)

Ben-Dayan, Ido; Westphal, Alexander; Wieck, Clemens; Jing, Shenglin; Toronto Univ., ON

2013-09-01

We analyze the possibility of realizing inflation with a subsequent dS vacuum in the Kaehler uplifting scenario. The inclusion of several quantum corrections to the 4d effective action evades previous no-go theorems and allows for construction of simple and successful models of string inflation. The predictions of several benchmark models are in accord with current observations, i.e., a red spectral index, negligible non-gaussianity, and spectral distortions similar to the simplest models of inflation. A particularly interesting subclass of models are ''left-rolling'' ones, where the overall volume of the compactified dimensions shrinks during inflation. We call this phenomenon ''inflation by deflation'' (IBD), where deflation refers to the internal manifold. This subclass has the appealing features of being insensitive to initial conditions, avoiding the overshooting problem, and allowing for observable running α -5 . The latter results differ significantly from many string inflation models.

Vibrational analysis of vertical axis wind turbine blades

Science.gov (United States)

Kapucu, Onur

The goal of this research is to derive a vibration model for a vertical axis wind turbine blade. This model accommodates the affects of varying relative flow angle caused by rotating the blade in the flow field, uses a simple aerodynamic model that assumes constant wind speed and constant rotation rate, and neglects the disturbance of wind due to upstream blade or post. The blade is modeled as elastic Euler-Bernoulli beam under transverse bending and twist deflections. Kinetic and potential energy equations for a rotating blade under deflections are obtained, expressed in terms of assumed modal coordinates and then plugged into Lagrangian equations where the non-conservative forces are the lift and drag forces and moments. An aeroelastic model for lift and drag forces, approximated with third degree polynomials, on the blade are obtained assuming an airfoil under variable angle of attack and airflow magnitudes. A simplified quasi-static airfoil theory is used, in which the lift and drag coefficients are not dependent on the history of the changing angle of attack. Linear terms on the resulting equations of motion will be used to conduct a numerical analysis and simulation, where numeric specifications are modified from the Sandia-17m Darrieus wind turbine by Sandia Laboratories.

Wind turbine wake in atmospheric turbulence

Energy Technology Data Exchange (ETDEWEB)

Rethore, P -E

2009-10-15

This thesis describes the different steps needed to design a steady-state computational fluid dynamics (CFD) wind farm wake model. The ultimate goal of the project was to design a tool that could analyze and extrapolate systematically wind farm measurements to generate wind maps in order to calibrate faster and simpler engineering wind farm wake models. The most attractive solution was the actuator disc method with the steady state k-epsilon turbulence model. The first step to design such a tool is the treatment of the forces. This thesis presents a computationally inexpensive method to apply discrete body forces into the finite-volume flow solver with collocated variable treatment (EllipSys), which avoids the pressure-velocity decoupling issue. The second step is to distribute the body forces in the computational domain accordingly to rotor loading. This thesis presents a generic flexible method that associates any kind of shapes with the computational domain discretization. The special case of the actuator disc performs remarkably well in comparison with Conway's heavily loaded actuator disc analytical solution and a CFD full rotor computation, even with a coarse discretization. The third step is to model the atmospheric turbulence. The standard k-epsilon model is found to be unable to model at the same time the atmospheric turbulence and the actuator disc wake and performs badly in comparison with single wind turbine wake measurements. A comparison with a Large Eddy Simulation (LES) shows that the problem mainly comes from the assumptions of the eddy-viscosity concept, which are deeply invalidated in the wind turbine wake region. Different models that intent to correct the k-epsilon model's issues are investigated, of which none of them is found to be adequate. The mixing of the wake in the atmosphere is a deeply non-local phenomenon that is not handled correctly by an eddy-viscosity model such as k-epsilon. (author)

Wind turbine wake in atmospheric turbulence

Energy Technology Data Exchange (ETDEWEB)

Rethore, P.-E.

2009-10-15

This thesis describes the different steps needed to design a steady-state computational fluid dynamics (CFD) wind farm wake model. The ultimate goal of the project was to design a tool that could analyze and extrapolate systematically wind farm measurements to generate wind maps in order to calibrate faster and simpler engineering wind farm wake models. The most attractive solution was the actuator disc method with the steady state k-epsilon turbulence model. The first step to design such a tool is the treatment of the forces. This thesis presents a computationally inexpensive method to apply discrete body forces into the finite-volume flow solver with collocated variable treatment (EllipSys), which avoids the pressure-velocity decoupling issue. The second step is to distribute the body forces in the computational domain accordingly to rotor loading. This thesis presents a generic flexible method that associates any kind of shapes with the computational domain discretization. The special case of the actuator disc performs remarkably well in comparison with Conway's heavily loaded actuator disc analytical solution and a CFD full rotor computation, even with a coarse discretization. The third step is to model the atmospheric turbulence. The standard k-epsilon model is found to be unable to model at the same time the atmospheric turbulence and the actuator disc wake and performs badly in comparison with single wind turbine wake measurements. A comparison with a Large Eddy Simulation (LES) shows that the problem mainly comes from the assumptions of the eddy-viscosity concept, which are deeply invalidated in the wind turbine wake region. Different models that intent to correct the k-epsilon model's issues are investigated, of which none of them is found to be adequate. The mixing of the wake in the atmosphere is a deeply non-local phenomenon that is not handled correctly by an eddy-viscosity model such as k-epsilon. (author)

In the wind of change. The wind power as pacesetters and guide to a fast turn to renewable energies; Im Wind des Wandels. Die Windkraft als Schrittmacher und Wegweiser zu einer schnellen Wende zu Erneuerbaren Energien

Energy Technology Data Exchange (ETDEWEB)

Scheer, H.; Alt, F.

2007-07-01

All renewable energy potentials (water power, bioenergy, wave power, geothermal energy) clearly are widespread as oil, natural gas, coal or uranium. For these potentials there are natural, spatial restrictions. In contrast to this, there exist any spatial restrictions for solar power and wind force. Under this aspect, the author of the contribution under consideration reports on wind force as a pacesetter and guide to a fast turn to renewable energy. Solar energy and wind energy have two crucial advantages of realizations: (a) The solar power plants and wind power plants can be installed faster than all other plants for generation of electrical power; (b) Solar power plants and wind power plants enable a radical shortening and simplification for the power supply. The generation and supply of electricity from solar power and wind power are also economically undefeatable. It is not a utopia to increase the contribution of the wind energy at the German power generation on basis of the renewable energy law in few years on over 40 %. The thesis, a further development of the wind power only is possible with offshore installations, because no suitable locations are present in the inland, is not correct. The emphasis of the use of wind power must remain with onshore plants. A broad dispersion of wind power plants should have priority, because the grid entrance is more easily realizable. The political attention must be directed toward the overcoming of the permission obstacles. Wind energy enables the passing of electricity from the shade of atomic and fossil power supply.

Nonlinear soil-structure interaction due to base slab uplift on the seismic response of an HTGR plant

International Nuclear Information System (INIS)

Kennedy, R.P.; Short, S.A.; Wesley, D.A.; Lee, T.H.

1975-01-01

The importance of the nonlinear soil-structure interaction effects resulting from substantial base slab uplift occurring during a seismic excitation are evaluated. The structure considered consisted of the containment building and prestressed concrete reactor vessel for a typical HTGR plant. A simplified dynamic mathematical model was utilized consisting of a conventional lumped mass structure with soil-structure interaction accounted for by translational and rotational springs whose properties are determined by elastic half space theory. Three different site soil conditions (a rock site, a moderately stiff soil and a soft soil site) and two levels of horizontal ground motion (0.3g and 0.5g earthquakes) were considered. It may be concluded that linear analysis can be used to conservatively estimate the important behavior of the base slab, even under conditions of substantial base slab uplift. For all cases investigated, linear analysis resulted in higher base overturning moments, greater toe pressures, and greater heel uplift distances than nonlinear analyses. It may also be concluded that the nonlinear effect of uplift does not result in any significant lengthening of the fundamental period of the structure. Also, except in the short period region only negligible differences exist between instructure response spectra based on linear analysis and those based on nonlinear analysis. Finally, for sites in which soil-structure interaction is not significant, as for the rock site, the peak structural response at all locations above the base mat are not significantly influenced by the nonlinear effects of base slab uplift. However, for the two soil sites, the peak shears and moments are, in a few instances, significantly different between linear and nonlinear analyses

Wind farm density and harvested power in very large wind farms: A low-order model

Science.gov (United States)

Cortina, G.; Sharma, V.; Calaf, M.

2017-07-01

In this work we create new understanding of wind turbine wakes recovery process as a function of wind farm density using large-eddy simulations of an atmospheric boundary layer diurnal cycle. Simulations are forced with a constant geostrophic wind and a time varying surface temperature extracted from a selected period of the Cooperative Atmospheric Surface Exchange Study field experiment. Wind turbines are represented using the actuator disk model with rotation and yaw alignment. A control volume analysis around each turbine has been used to evaluate wind turbine wake recovery and corresponding harvested power. Results confirm the existence of two dominant recovery mechanisms, advection and flux of mean kinetic energy, which are modulated by the background thermal stratification. For the low-density arrangements advection dominates, while for the highly loaded wind farms the mean kinetic energy recovers through fluxes of mean kinetic energy. For those cases in between, a smooth balance of both mechanisms exists. From the results, a low-order model for the wind farms' harvested power as a function of thermal stratification and wind farm density has been developed, which has the potential to be used as an order-of-magnitude assessment tool.

Floating wind turbine system

Science.gov (United States)

Viterna, Larry A. (Inventor)

2009-01-01

A floating wind turbine system with a tower structure that includes at least one stability arm extending therefrom and that is anchored to the sea floor with a rotatable position retention device that facilitates deep water installations. Variable buoyancy for the wind turbine system is provided by buoyancy chambers that are integral to the tower itself as well as the stability arm. Pumps are included for adjusting the buoyancy as an aid in system transport, installation, repair and removal. The wind turbine rotor is located downwind of the tower structure to allow the wind turbine to follow the wind direction without an active yaw drive system. The support tower and stability arm structure is designed to balance tension in the tether with buoyancy, gravity and wind forces in such a way that the top of the support tower leans downwind, providing a large clearance between the support tower and the rotor blade tips. This large clearance facilitates the use of articulated rotor hubs to reduced damaging structural dynamic loads. Major components of the turbine can be assembled at the shore and transported to an offshore installation site.

New Solutions to Line-Driven Winds of Hot Massive Stars

Science.gov (United States)

Gormaz-Matamala, Alex C.; Curé, Michel; Cidale, Lydia; Venero, Roberto

2017-11-01

In the frame of radiation driven wind theory (Castor et al.1975), we present self-consistent hydrodynamical solutions to the line-force parameters (k, α, δ) under LTE conditions. Hydrodynamic models are provided by HydWind (Curé 2004). We evaluate these results with those ones previously found in literature, focusing in different regions of the optical depth to be used to perform the calculations. The values for mass-loss rate and terminal velocity obtained from our calculations are also presented. We also examine the line-force parameters for the case when large changes in ionization throughout the wind occurs (δ-slow solutions, Curé et al.2011).

Wind Energy Forecasting: A Collaboration of the National Center for Atmospheric Research (NCAR) and Xcel Energy

Energy Technology Data Exchange (ETDEWEB)

Parks, K.; Wan, Y. H.; Wiener, G.; Liu, Y.

2011-10-01

The focus of this report is the wind forecasting system developed during this contract period with results of performance through the end of 2010. The report is intentionally high-level, with technical details disseminated at various conferences and academic papers. At the end of 2010, Xcel Energy managed the output of 3372 megawatts of installed wind energy. The wind plants span three operating companies1, serving customers in eight states2, and three market structures3. The great majority of the wind energy is contracted through power purchase agreements (PPAs). The remainder is utility owned, Qualifying Facilities (QF), distributed resources (i.e., 'behind the meter'), or merchant entities within Xcel Energy's Balancing Authority footprints. Regardless of the contractual or ownership arrangements, the output of the wind energy is balanced by Xcel Energy's generation resources that include fossil, nuclear, and hydro based facilities that are owned or contracted via PPAs. These facilities are committed and dispatched or bid into day-ahead and real-time markets by Xcel Energy's Commercial Operations department. Wind energy complicates the short and long-term planning goals of least-cost, reliable operations. Due to the uncertainty of wind energy production, inherent suboptimal commitment and dispatch associated with imperfect wind forecasts drives up costs. For example, a gas combined cycle unit may be turned on, or committed, in anticipation of low winds. The reality is winds stayed high, forcing this unit and others to run, or be dispatched, to sub-optimal loading positions. In addition, commitment decisions are frequently irreversible due to minimum up and down time constraints. That is, a dispatcher lives with inefficient decisions made in prior periods. In general, uncertainty contributes to conservative operations - committing more units and keeping them on longer than may have been necessary for purposes of maintaining reliability

Airfoil characteristics for wind turbines

OpenAIRE

Bak, C.; Fuglsang, P.; Sørensen, Niels N.; Aagaard Madsen, Helge; Shen, W.Z.; Sørensen, Jens Nørkær

1999-01-01

Airfoil characteristics for use in the Blade Element Momentum (BEM) method calculating the forces on Horizontal Axis Wind Turbines (HAWT) are derived by use of systematic methods. The investigation and derivation of the airfoil characteristics are basedon four different methods: 1) Inverse momentum theory, 2) Actuator disc theory, 3) Numerical optimisation and 4) Quasi-3D CFD computations. The two former methods are based on 3D CFD computations and wind tunnel measurements on a 41-m full-scal...

Stellar winds in binary X-ray systems

Science.gov (United States)

Macgregor, K. B.; Vitello, P. A. J.

1982-01-01

It is thought that accretion from a strong stellar wind by a compact object may be responsible for the X-ray emission from binary systems containing a massive early-type primary. To investigate the effect of X-ray heating and ionization on the mass transfer process in systems of this type, an idealized model is constructed for the flow of a radiation-driven wind in the presence of an X-ray source of specified luminosity, L sub x. It is noted that for low values of L sub x, X-ray photoionization gives rise to additional ions having spectral lines with wavelengths situated near the peak of the primary continuum flux distribution. As a consequence, the radiation force acting on the gas increases in relation to its value in the absence of X-rays, and the wind is accelerated to higher velocities. As L sub x is increased, the degree of ionization of the wind increases, and the magnitude of the radiation force is diminished in comparison with the case in which L sub x = 0. This reduction leads at first to a decrease in the wind velocity and ultimately (for L sub x sufficiently large) to the termination of radiatively driven mass loss.

Wind Powering America FY06 Activities Summary

Energy Technology Data Exchange (ETDEWEB)

2007-02-01

The Wind Powering America FY06 Activities Summary reflects the accomplishments of our state wind working groups, our programs at the National Renewable Energy Laboratory, and our partner organizations. The national WPA team remains a leading force for moving wind energy forward in the United States. WPA continues to work with its national, regional, and state partners to communicate the opportunities and benefits of wind energy to a diverse set of stakeholders. WPA now has 29 state wind working groups (welcoming New Jersey, Indiana, Illinois, and Missouri in 2006) that form strategic alliances to communicate wind's benefits to the state stakeholders. More than 120 members of national and state public and private sector organizations from 34 states attended the 5th Annual WPA All-States Summit in Pittsburgh in June.

Coseismic Coastal Uplift from the 2012 Mw7.6 Nicoya Earthquake, Costa Rica: Implications of Megathrust Rupture for Fore Arc Morphotectonics

Science.gov (United States)

Marshall, J.; Morrish, S.; Newman, A. V.; Protti, M.

2013-05-01

The 2012 Mw7.6 Nicoya Earthquake ruptured the subduction megathrust beneath the Nicoya Peninsula, Costa Rica. Local network data place the hypocenter 10 km offshore at 15 km depth. Within 5 days, >1500 aftershocks outlined a principal rupture zone of 1500 km2 beneath the central Nicoya coast. Despite its large magnitude and proximity to populated areas, the Nicoya Earthquake produced only moderate damage ( $45 million) and few casualties (≤200 injured, 0 deaths) localized in areas of strong ground motion (MM=VII) on the Nicoya Peninsula and Central Volcanic Cordillera. Rapid response geomorphic and geodetic fieldwork was conducted 5-15 days after the earthquake to constrain patterns of coseismic deformation across the Nicoya Peninsula. Geomorphic data include: 1) pre/post earthquake coastal monument surveys, 2) reoccupied coastal survey lines, 3) pre/post earthquake high-tide debris lines, 4) displaced high tide notches and rock staining, 5) vertical extent of mortality (VEM) for sessile intertidal organisms, 6) coastal stream incision and mangrove root exposure. Measurements at 22 field sites record recognizable coseismic uplift along 80 km of coastline between Playa Avellanas and Punta Coyote. Pronounced uplift (≥0.5 m) occurred along 30 km of coast from Nosara to Islita, with maximum uplift (≥0.8 m) near Puerto Carrillo onshore of the epicenter. The observed geomorphic uplift pattern is consistent with that recorded by continuous GPS stations (although GPS values are systematically lower), and with seismic and geodetic inversions for primary slip centered beneath the Nicoya coast. The Nicoya Peninsula forms a prominent morphologic high along the Middle America fore arc. This emergent coastal landmass overlies a strongly coupled seismogenic zone that produced major earthquakes in 1853, 1900, 1950, and 2012. The 2012 coseismic uplift pattern coincides with the area of GPS-modeled pre-event locking (Feng et al., 2012), the estimated rupture area for the prior

Detection of fast nanoparticles in the solar wind

International Nuclear Information System (INIS)

Meyer-Vernet, N.; Maksimovic, M.; Lecacheux, A.; Le Chat, G.; Czechowski, A.; Mann, I.; Goetz, K.; Kaiser, M. L.; Cyr, O. C. St.; Bale, S. D.

2010-01-01

Dust grains in the nanometer range bridge the gap between atoms and larger grains made of bulk material. Their small size embodies them with special properties. Due to their high relative surface area, they have a high charge-to-mass ratio, so that the Lorentz force in the solar wind magnetic field exceeds the gravitational force and other forces by a large amount, and they are accelerated to a speed of the order of magnitude of the solar wind speed. When such fast nanoparticles impact a spacecraft, they produce craters whose matter vaporises and ionises, yielding transient voltages as high as do much larger grains of smaller speed. These properties are at the origin of their recent detection at 1 AU in the solar wind. We discuss the detection of fast nanoparticles by wave instruments of different configurations, with applications to the recent detections on STEREO/WAVES and CASSINI/RPWS. Finally we discuss the opportunities for nanoparticle detection by wave instruments on future missions and/or projects in the inner heliosphere such as Bepi-Colombo and Solar Orbiter.

Laddermill-sailing. Ship propulsion by wind energy independent from the wind direction

Energy Technology Data Exchange (ETDEWEB)

Ockels, W. J.

2007-12-15

The use of large kites in ship propulsion has been getting a growing attention because of the urgent need to reduce the CO2 production and thus stop the use of fossil fuels. A novel application of ship propulsion by kites is proposed based on a Laddermill apparatus mounted on a ship. Such an apparatus consist of a winch, an electric motor/generator, a kite system (including launch and retrieval) and controlling electronics. Rather than the traditional sailing by wind force the Laddermill propulsion is achieved by a combination of the production and use of electrical power and the direct pulling force from the kite system. The feasibility of this application is investigated. It is shown that when the overall Laddermill to ship thrust efficiency can be made around 50% the resulting speed of the ship becomes practically independent from the wind direction. Such a capability could thus well change the world's seafaring.

Forces in electromagnetic field and gravitational field

OpenAIRE

Weng, Zihua

2008-01-01

The force can be defined from the linear momentum in the gravitational field and electromagnetic field. But this definition can not cover the gradient of energy. In the paper, the force will be defined from the energy and torque in a new way, which involves the gravitational force, electromagnetic force, inertial force, gradient of energy, and some other new force terms etc. One of these new force terms can be used to explain why the solar wind varies velocity along the magnetic force line in...

Explaining the Diverse Response of the Ultra-relativistic Van Allen Radiation Belt to Solar Wind Forcing

Science.gov (United States)

Mann, I. R.; Ozeke, L.; Murphy, K. R.; Claudepierre, S. G.; Rae, J.; Milling, D. K.; Kale, A.; Baker, D. N.

2017-12-01

The NASA Van Allen Probes have opened a new window on the dynamics of ultra-relativistic electrons in the Van Allen radiation belts. Under different solar wind forcing the outer belt is seen to respond in a variety of apparently diverse and sometimes remarkable ways. For example, sometimes a third radiation belt is carved out (e.g., September 2012), or the belts can remain depleted for 10 days or more (September 2014). More usually there is a sequential response of a strong and sometimes rapid depletion followed by a re-energization, the latter increasing outer belt electron flux by orders of magnitude on hour timescales during some of the strongest storms of this solar cycle (e.g., March 2013, March 2015). Such dynamics also appear to be often bounded at low-L by an apparently impenetrable barrier at L 2.8 through which ultra-relativistic electrons do not penetrate. Many studies in the Van Allen Probes era have sought explanations for these apparently diverse features, often incorporating the effects from multiple plasma waves. In contrast, we show how this apparently diverse behaviour can instead be explained by one dominant process: ULF wave radial transport. Once ULF wave transport rates are accurately specified by observations, and coupled to the dynamical variation of the outer boundary condition at the edge of the outer belt, the observed diverse responses can all be explained. However, in order to get good agreement with observations, the modeling reveals the importance of still currently unexplained very fast loss in the main phase which results in an almost total extinction of the belts and decouples pre- and post-storm ultra-relativistic electron flux on hour timescales. Similarly, varying plasmasheet source populations are seen to be of critical importance such that near-tail dynamics play a crucial role in Van Allen belt dynamics. Nonetheless, simple models incorporating accurate transport rates derived directly from ULF wave measurements are shown to

Soil erosion rates from mixed soil and gravel surfaces in a wind tunnel: A preliminary report

International Nuclear Information System (INIS)

Ligotke, M.W.

1988-12-01

Tests of wind erosion were performed in a controlled-environment wind tunnel to support the development of natural-material protective barriers for long-term isolation of radioactive waste. Barrier performance standards currently being developed for internal and external barrier performance are expected to mandate a surface layer that is resistant to wind erosion. The purpose of this study was to initiate a series of tests to determine suitable soil and gravel mixtures for such a barrier and to test worst-case surface layer conditions under the influence of high wind speeds. Six mixed soil and gravel surfaces were prepared, weathered to represent natural wind-blown desert areas, and subjected to controlled wind erosion forces in a wind tunnel. The applied erosive forces, including surface shear forces, were characterized to provide a means of relating wind tunnel results with actual field conditions. Soil particle losses from the surfaces caused by suspension, saltation, and surface creep were monitored by aerosol sample probes and mass balance measurements. 23 refs., 22 figs., 3 tabs

Wind Extraction for Natural Ventilation

Science.gov (United States)

Fagundes, Tadeu; Yaghoobian, Neda; Kumar, Rajan; Ordonez, Juan

2017-11-01

Due to the depletion of energy resources and the environmental impact of pollution and unsustainable energy resources, energy consumption has become one of the main concerns in our rapidly growing world. Natural ventilation, a traditional method to remove anthropogenic and solar heat gains, proved to be a cost-effective, alternative method to mechanical ventilation. However, while natural ventilation is simple in theory, its detailed design can be a challenge, particularly for wind-driven ventilation, which its performance highly involves the buildings' form, surrounding topography, turbulent flow characteristics, and climate. One of the main challenges with wind-driven natural ventilation schemes is due to the turbulent and unpredictable nature of the wind around the building that impose complex pressure loads on the structure. In practice, these challenges have resulted in founding the natural ventilation mainly on buoyancy (rather than the wind), as the primary force. This study is the initial step for investigating the physical principals of wind extraction over building walls and investigating strategies to reduce the dependence of the wind extraction on the incoming flow characteristics and the target building form.

Understanding the uplift pattern in Mesozoic and Cenozoic,, eastern Dabie area, China using fission track dating of apatite

International Nuclear Information System (INIS)

Wu Qianhong; Liu Shunsheng

2002-01-01

By using the fission track dating technique, a preliminary study was carried out on the fission track ages (FTA) of apatite, their distribution patterns and hints over the tectonics activities during Mesozoic and Cenozoic in the east Dabie area. Attempts were also made to improve the conventional statistical method for the tracks. Ranging from 59.4 +- 3.4 Ma to 105.6 +- 9.8 Ma, the FTA results of apatite spread in the wide range and increased rapidly from the east to the west area. Sine 95 Ma, the uplift rate has been quite slow and asymmetry. The FTA value in the middle area of Xiaotian-Mozitan Fault may imply its uplift in Cretaceous. The faulting should be the main control factor for the uplift of this area

Stellar and wind parameters of massive stars from spectral analysis

Science.gov (United States)

Araya, Ignacio; Curé, Michel

2017-11-01

The only way to deduce information from stars is to decode the radiation it emits in an appropriate way. Spectroscopy can solve this and derive many properties of stars. In this work we seek to derive simultaneously the stellar and wind characteristics of a wide range of massive stars. Our stellar properties encompass the effective temperature, the surface gravity, the stellar radius, the micro-turbulence velocity, the rotational velocity and the Si abundance. For wind properties we consider the mass-loss rate, the terminal velocity and the line-force parameters α, k and δ (from the line-driven wind theory). To model the data we use the radiative transport code Fastwind considering the newest hydrodynamical solutions derived with Hydwind code, which needs stellar and line-force parameters to obtain a wind solution. A grid of spectral models of massive stars is created and together with the observed spectra their physical properties are determined through spectral line fittings. These fittings provide an estimation about the line-force parameters, whose theoretical calculations are extremely complex. Furthermore, we expect to confirm that the hydrodynamical solutions obtained with a value of δ slightly larger than ~ 0.25, called δ-slow solutions, describe quite reliable the radiation line-driven winds of A and late B supergiant stars and at the same time explain disagreements between observational data and theoretical models for the Wind-Momentum Luminosity Relationship (WLR).

Ca isotopes reveal weak control of tectonic uplift on long-term climate change

Science.gov (United States)

Moore, J.; Jacobson, A. D.; Holmden, C. E.; Craw, D.

2010-12-01

Ca-Mg silicate weathering consumes atmospheric CO2 over geological timescales (≥106 yr) whereas carbonate weathering has no effect. High Ca fluxes from active orogens have been used to argue that mountain uplift is a disproportionately large CO2 sink. To test this hypothesis, it is essential to determine proportions of Ca from silicate versus carbonate weathering. High precision measurement of Ca isotopes (δ44/40Ca) provides a novel method to directly quantify Ca sources. To this end, we examined δ44/40Ca in rivers draining the Southern Alps of New Zealand. The Southern Alps have large tectonic and climatic gradients but nearly constant bedrock chemistry. West of the main topographic divide, uplift and precipitation rates are high, and steep, fast-flowing rivers drain schist. East of the divide, uplift and precipitation rates are low, and low-gradient, braided rivers drain either schist or greywacke. Both schist and greywacke contain up to 3% hydrothermal and metamorphic calcite. Glaciers feed several schist and greywacke catchments. Examined as δ44/40Ca versus Sr/Ca, values measured for carbonate and silicate end-members define two-component mixing envelopes. Rivers west of the divide plot within the envelope, ruling out isotopic fractionation as a factor for these streams. Several rivers east of the divide are 40Ca enriched relative to the envelope. In-situ fractionation of stream water Ca cannot explain this pattern because fractionation is expected to preferentially remove 40Ca. We measured δ42/44Ca ratios to test if chemical weathering preferentially releases 40Ca. When examined as δ40/44Ca versus δ42/44Ca, the data only display mass-dependent isotope effects. Ca in grass and the exchangeable pool of shallow soils is enriched in 40Ca relative to waters and bedrock. This Ca defines a third mixing end-member that contributes 15-30% of the Ca in rivers east of the divide. Evidence of the plant-fractionated signal likely reflects water residence times

Mesoscale wind fluctuations over Danish waters

DEFF Research Database (Denmark)

Vincent, Claire Louise

in generated power are a particular problem for oshore wind farms because the typically high concentration of turbines within a limited geographical area means that uctuations can be correlated across large numbers of turbines. Furthermore, organised mesoscale structures that often form over water......Mesoscale wind uctuations aect the large scale integration of wind power because they undermine the day-ahead predictability of wind speed and power production, and because they can result in large uctuations in power generation that must be balanced using reserve power. Large uctuations...... that realistic hour-scale wind uctuations and open cellular convection patterns develop in WRF simulations with 2km horizontal grid spacing. The atmospheric conditions during one of the case studies are then used to initialise a simplied version of the model that has no large scale weather forcing, topography...

Error analysis and assessment of unsteady forces acting on a flapping wing micro air vehicle: free flight versus wind-tunnel experimental methods.

Science.gov (United States)

Caetano, J V; Percin, M; van Oudheusden, B W; Remes, B; de Wagter, C; de Croon, G C H E; de Visser, C C

2015-08-20

An accurate knowledge of the unsteady aerodynamic forces acting on a bio-inspired, flapping-wing micro air vehicle (FWMAV) is crucial in the design development and optimization cycle. Two different types of experimental approaches are often used: determination of forces from position data obtained from external optical tracking during free flight, or direct measurements of forces by attaching the FWMAV to a force transducer in a wind-tunnel. This study compares the quality of the forces obtained from both methods as applied to a 17.4 gram FWMAV capable of controlled flight. A comprehensive analysis of various error sources is performed. The effects of different factors, e.g., measurement errors, error propagation, numerical differentiation, filtering frequency selection, and structural eigenmode interference, are assessed. For the forces obtained from free flight experiments it is shown that a data acquisition frequency below 200 Hz and an accuracy in the position measurements lower than ± 0.2 mm may considerably hinder determination of the unsteady forces. In general, the force component parallel to the fuselage determined by the two methods compares well for identical flight conditions; however, a significant difference was observed for the forces along the stroke plane of the wings. This was found to originate from the restrictions applied by the clamp to the dynamic oscillations observed in free flight and from the structural resonance of the clamped FWMAV structure, which generates loads that cannot be distinguished from the external forces. Furthermore, the clamping position was found to have a pronounced influence on the eigenmodes of the structure, and this effect should be taken into account for accurate force measurements.

Raised marine terraces in the Northern Calabrian Arc (Southern Italy: a ~ 600 kyr-long geological record of regional uplift

Directory of Open Access Journals (Sweden)

L. Cucci

2004-06-01

Full Text Available The Sibari Plain in the Northeastern Calabrian Arc displays a well-developed suite of marine terraces. This paper deals with i the identification and correlation of the terraces; ii their age assignment and a tentative reconstruction of the uplift history of the area; iii the relationships between terraces and major faults in the study area and between uplift in the Plain and pattern of Quaternary uplift throughout the Calabrian Arc. Identifying wavecut platforms and inner-edge fragments over a linear extent of ~ 100 km was achieved by photo interpretation, 1:25 000 scale map analyses and field survey. Morphological evidence led to the correlation of the identified fragments into five complete strandlines (numbered #1 to #5 lowest to highest, at elevations ranging from 60 m to ~ 650 m. Analysis of two parameters of the emerged platform-cliff systems, namely the platform-cliff ratio and the dissection percentage, further testifies that the two lowest terraces are strongly correlative. A 130 kyr AAR age of in situ fossil samples of Glycymeris collected at 114 m elevation within the deposit of Terrace #2 indicates a key correlation of T#2 with MIS 5.5 (the peak of the last interglacial, 124 kyr, i.e. an uplift rate of ~ 0.98 mm/yr for this strandline. The other four terraces have been tentatively associated with MIS 5.3, 7, 9 and 15. Geological observations independent of geochronological evidence provide consistent lower age boundaries for the terraces and supply further constraints to this interpretation. Investigating the relations between setting of the terraces and location of major tectonic structures in the region is suggestive of no recent activity of two previously recognized faults, the «Sangineto Line» and the «Corigliano-Rossano Line». Instead, some limited anomalies that affect the terraces are tentatively associated with the activity of the Castrovillari Fault. Therefore, sustained uplift has been the long-term dominant

Cyprininae phylogeny revealed independent origins of the Tibetan Plateau endemic polyploid cyprinids and their diversifications related to the Neogene uplift of the plateau.

Science.gov (United States)

Wang, Xuzhen; Gan, Xiaoni; Li, Junbing; Chen, Yiyu; He, Shunping

2016-11-01

Origin and diversification of the Tibetan polyploid cyprinids (schizothoracins) may help us to explore relationships between diversification of the cyprinids and the Tibetan Plateau uplift. Cyprininae phylogeny was analyzed using mitochondrial and nuclear DNA sequences to trace origins of polyploidy and diversifications of schizothoracins. Ancestral states reconstruction for ploidy levels indicated that the Cyprininae was diploid origin and the schizothoracin clades tetraploid origins. There were two diversification rate shifts along with diversification of the cyprinine fishes in response to the Tibetan uplift. The unusual diversification shifts were located to branches subtending the clades of Tibetan polyploid cyprinids. Our analyses suggested that (i) phylogeny of Cyprininae recovered two independent origins of the Tibetan polyploidy schizothoracins; (ii) diversifications of the schizothoracins were closely related to the Neogene uplift of the Tibetan plateau in the following ways: the relatively ancient Late Oligocene-Middle Miocene adaptive radiation may be associated with the uplift of the southern Tibet and Himalaya; the Middle Miocene-Early Pleistocene lineage-specific diversification broadly coincident with major phase of the Neogene Tibetan uplift; and the most recent Pleistocene diversification shift in Schizothorax closely coincident with the successive Kunlun-Huanghe and Gonghe movements of the Tibetan uplift and the glaciation-induced climate oscillations on the plateau.

Tribological Aspects of the Process of Winding the Steel Rope Around the Winch Drum

Directory of Open Access Journals (Sweden)

M. Matejić, , , ,

2014-03-01

Full Text Available Proper winding of the steel rope around the winch drum is great importance, mostly for: prolonging the service life of the rope, reduction of deformations of the body and the sides of the drum if the winding of the rope is multilayered, increasing of the safety factors, easier unwinding of the rope while lowering the load, even running of the drive unit, etc. The focus of this paper is on the analysis of the friction which occurs in the process of winding and unwinding the rope around the winch drum. Friction force is in its highest intensity when the rope passes from one layer to another, if the winding of the rope is multilayered. As the result of the research, certain mechanisms of winding of the rope from the aspects of the friction force were obtained, and the effects of the forces on the sides of the drum were analyzed.

Analysis of vehicle dynamics under sadden cross wind

Science.gov (United States)

Walczak, S.

2016-09-01

In this paper, the way of calculating aerodynamic forces acting on a vehicle passing in the region of sadden cross wind was presented. The CarDyn, a vehicle dynamics simulation program, developed by the author was used. The effects of the cross wind were studied with a fixed steering wheel simulation. On the base of computer simulations the car cross wind sensitivity were determined, and vehicle responses such as lateral offset, side acceleration and yaw angular velocity are presented.

Measured and modelled local wind field over a frozen lake in a mountainous area

Energy Technology Data Exchange (ETDEWEB)

Smedman, A.S.; Bergstroem, H.; Hoegstroem, U. [Uppsala Univ. (Sweden). Dept. of Meteorology

1996-03-01

The study is a follow-up of a previous paper and concentrates on two very characteristic flow regimes: forced channeling, where the driving geostrophic wind and the lake axis are roughly aligned, and pressure-driven channeling or gap winds, which are characterized by a geostrophic wind direction more or less perpendicular to the lake axis. Both situations produce winds along the main axis of the lake. In the forced channeling case the wind direction varies insignificantly with height and the wind speed increases monotonically with height. The gap wind flow, which can give supergeostrophic speed, is restricted to the lowest 500 m above the lake surface, drops in speed to near zero just above that layer, changing to an across-wind direction higher up. Gap winds are found to require slightly stable stratification for their existence; strong stability forces the flow to go round the mountains rather than over, and neutral conditions give a turbulent wake in the lee of the mountains. The gap wind starts at any occasion as a sudden warm front approaching from either of the two along-lake directions (115 or 295 degrees). It is argued that the relative warmth of the `gap wind air` is due to air originally flowing at mountain top height across the lake axis being gradually turned and accelerated along the synoptic pressure gradient while descending. The strongly sheared layer at the top of the gap wind region is dynamically highly unstable, giving rise to vertically coherent variations in wind speed and direction which appear to be triggered by gravity waves. When the driving geostrophic wind is high enough, the disturbed region reaches all the way down to the ground surface. Then periods with strong turbulence and low mean wind alternate with pronounced gap winds on typically a 10 minute scale. 11 refs, 18 figs

A Literature Survey and Experimental Evaluation of the State-of-the-Art in Uplift Modeling: A Stepping Stone Toward the Development of Prescriptive Analytics.

Science.gov (United States)

Devriendt, Floris; Moldovan, Darie; Verbeke, Wouter

2018-03-01

Prescriptive analytics extends on predictive analytics by allowing to estimate an outcome in function of control variables, allowing as such to establish the required level of control variables for realizing a desired outcome. Uplift modeling is at the heart of prescriptive analytics and aims at estimating the net difference in an outcome resulting from a specific action or treatment that is applied. In this article, a structured and detailed literature survey on uplift modeling is provided by identifying and contrasting various groups of approaches. In addition, evaluation metrics for assessing the performance of uplift models are reviewed. An experimental evaluation on four real-world data sets provides further insight into their use. Uplift random forests are found to be consistently among the best performing techniques in terms of the Qini and Gini measures, although considerable variability in performance across the various data sets of the experiments is observed. In addition, uplift models are frequently observed to be unstable and display a strong variability in terms of performance across different folds in the cross-validation experimental setup. This potentially threatens their actual use for business applications. Moreover, it is found that the available evaluation metrics do not provide an intuitively understandable indication of the actual use and performance of a model. Specifically, existing evaluation metrics do not facilitate a comparison of uplift models and predictive models and evaluate performance either at an arbitrary cutoff or over the full spectrum of potential cutoffs. In conclusion, we highlight the instability of uplift models and the need for an application-oriented approach to assess uplift models as prime topics for further research.

Uplift along the western margin of the Deccan Basalt Province: Is ...

Indian Academy of Sciences (India)

and Planetary Change 58 310–334. Powar K B 1981 Lineament fabric and dyke pattern in the western part of the Deccan Volcanic Province; Geol. Soc. India Memoir 3 45–57. Powar K B 1993 Geomorphological evolution of Konkan coastal belt and adjoining Sahyadri uplands with refer- ence to Quaternary uplift; Curr. Sci.

International wind farm markets: An overview

Energy Technology Data Exchange (ETDEWEB)

Rackstraw, K. [American Wind Energy Association, Washington, DC (United States)

1996-12-31

More wind energy capacity was installed in 1995 than in any previous year. Two markets, Germany and India, accounted for nearly two-thirds of those installations, while the largest single market in the world historically, the US, ground nearly to a halt. Market supports in Germany and India, however, are vulnerable to political forces largely beyond the control of the wind industry. This paper examines the growth of international wind farm markets worldwide and notes that future markets will be more broadly based, leaving the industry less vulnerable to political changes. The paper also concludes that an additional 18,500 MW could be installed by the year 2005 even without assuming a dire ecological scenario that would create environmental drivers to accelerate wind market growth. 4 figs.

Episodes of subsidence and uplift of the conjugate margins of Greenland and Norway after opening of the NE Atlantic

Science.gov (United States)

Japsen, Peter; Green, Paul F.; Bonow, Johan M.; Chalmers, James A.

2015-04-01

We have undertaken a regional study of the thermo-­tectonic development of East Greenland (68-75°N) and of southern Norway (58-64°N). We take advantage of the general observation that that the effects of uplift often are reflected more clearly onshore than offshore, and of the specific condition that the mountains of southern East Greenland expose thick basalts that were extruded onto a largely horizontal lava plain near sea level during breakup of the NE Atlantic at the Paleocene-Eocene transition. It is thus clear that the present-­day elevation of these basalts up to 3.7 km a.s.l. were reached after breakup. Our results based on apatite fission-­track analysis (AFTA) data from East Greenland reveal a long history of post-­Palaeozoic burial and exhumation across the region and show that the terrains of Palaeozoic and older rocks were buried below a 2-3 km­-thick cover prior to a series of Mesozoic events of uplift and exhumation. The AFTA results from southern Norway reveal events of Mesozoic uplift and exhumation that are broadly simultaneous with those in Greenland. Volcanic and sedimentary rocks accumulated on the subsiding, East Greenland margin during and following breakup and then began to be exhumed during late Eocene uplift that preceded a major, early Oligocene plate reorganization in the NE Atlantic. The Norwegian margin also experienced Eocene subsidence and burial. Our AFTA data from southern Norway show evidence of an event of mid­Cenozoic uplift and exhumation that overlap with the early Oligocene onset of progradation of clastic wedges towards the south and with the formation of a major, late Eocene unconformity along the NW European margin. The uplift event at the Eocene-Oligocene transition that affected wide areas in the NE Atlantic domain was followed by two regional events of uplift and incision of the East Greenland margin in the late Miocene and Pliocene whereas the Neogene uplift of southern Norway began in the early Miocene and was

SAPS effects on thermospheric winds during the 17 March 2013 storm

Science.gov (United States)

Sheng, C.; Lu, G.; Wang, W.; Doornbos, E.; Talaat, E. R.

2017-12-01

Strong subauroral polarization streams (SAPS) were observed by DMSP satellites during the main phase of the 17 March 2013 geomagnetic storm. Both DMSP F18 and GOCE satellites sampled at 19 MLT during this period, providing near-simultaneous measurements of ion drifts and neutral winds near dusk. The fortuitous satellite conjunction allows us to directly examine the SAPS effects on thermospheric winds. In addition, two sets of model runs were carried out for this event: (1) the standard TIEGCM run with high-latitude forcing; (2) the SAPS-TIEGCM run by incoporating an empirical model of SAPS in the subauroral zone. The difference between these two runs represents the influence of SAPS forcing. In particular, we examine ion-neutral coupling at subauroral latitudes through detailed forcing term analysis to determine how the SAPS-related strong westward ion drifts alter thermospheric winds.

On trends in historical marine wind data

Science.gov (United States)

Cardone, Vincent J.; Greenwood, Juliet G.; Cane, Mark A.

1990-01-01

Long-period variations which include a trend toward strengthening winds over the last three decades have on the one hand been suggested to be real climatic changes, and on the other artifacts of the evolution of measuring techniques. An examination is presently conducted of individual ship reports from three regions with high data densities, in order to resolve this dispute. Even with corrections for instrumental effects, the pre-1950 winds appear weaker than post-1950 winds; the most probable explanation is the absence of universal sea state and Beaufort force standards prior to 1946.

Measuring power output intermittency and unsteady loading in a micro wind farm model

OpenAIRE

Bossuyt, Juliaan; Howland, Michael; Meneveau, Charles; Meyers, Johan

2016-01-01

In this study porous disc models are used as a turbine model for a wind-tunnel wind farm experiment, allowing the measurement of the power output, thrust force and spatially averaged incoming velocity for every turbine. The model's capabilities for studying the unsteady turbine loading, wind farm power output intermittency and spatio temporal correlations between wind turbines are demonstrated on an aligned wind farm, consisting of 100 wind turbine models.

Wind Power Plants Fundamentals, Design, Construction and Operation

CERN Document Server

Twele, Jochen

2012-01-01

Wind power plants teaches the physical foundations of usage of Wind Power. It includes the areas like Construction of Wind Power Plants, Design, Development of Production Series, Control, and discusses the dynamic forces acting on the systems as well as the power conversion and its connection to the distribution system. The book is written for graduate students, practitioners and inquisitive readers of any kind. It is based on lectures held at several universities. Its German version it already is the standard text book for courses on Wind Energy Engineering but serves also as reference for practising engineers.

Effect of Second-Order Hydrodynamics on a Floating Offshore Wind Turbine

Energy Technology Data Exchange (ETDEWEB)

Roald, L.; Jonkman, J.; Robertson, A.

2014-05-01

The design of offshore floating wind turbines uses design codes that can simulate the entire coupled system behavior. At the present, most codes include only first-order hydrodynamics, which induce forces and motions varying with the same frequency as the incident waves. Effects due to second- and higher-order hydrodynamics are often ignored in the offshore industry, because the forces induced typically are smaller than the first-order forces. In this report, first- and second-order hydrodynamic analysis used in the offshore oil and gas industry is applied to two different wind turbine concepts--a spar and a tension leg platform.

Ocean's response to Hurricane Frances and its implications for drag coefficient parameterization at high wind speeds

KAUST Repository

Zedler, S. E.; Niiler, P. P.; Stammer, D.; Terrill, E.; Morzel, J.

2009-01-01

with realistic stratification and forcing fields representing Hurricane Frances, which in early September 2004 passed east of the Caribbean Leeward Island chain. The model was forced with a NOAA-HWIND wind speed product after converting it to wind stress using

Reduction mechanism of dynamic loads on down wind rotor; Furyoku hatsuden system down wind rotor no doteki kaju no keigen kiko ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Seki, K; Shimizu, Y; Yasui, T [Tokai University, Tokyo (Japan)

1997-11-25

Dynamic force on blades in a large wind mill changes with rotational speed for various reasons, such as wind shear that causes vertical distribution of wind velocity or titling angle. Therefore, a 2-blade system on a teetered hub is a practical selection for the coned, down-wind type. Use of teetered axis greatly reduces bending moment in the flap direction and that at the axis of rotation. An attempt was made to understand dynamic loads by inertial force resulting from oscillation of the blade rotating on the teetered axis, and thereby to avoid them. The in-plane load can be diminished to zero when the teetered axis is coincided with the center of gravity, but generally cannot be avoided when the blade is strained significantly, except it is operated at the rated condition. The in-plane load and bending moment can be avoided, when rotational freedom is given around the y axis. Dynamic load on a down-wind rotor can be avoided by use of universal joint. 3 refs., 6 figs.

Evidence for Late Pleistocene uplift at the Somma-Vesuvius apron near Pompeii

Science.gov (United States)

Marturano, Aldo; Aiello, Giuseppe; Barra, Diana

2011-05-01

Detailed stratigraphic and micropalaeontological analyses of samples from boreholes at the Somma-Vesuvius apron, between Pompeii and the sea, allowed reconstruction of Late Quaternary palaeoenvironmental evolution of the Sarno coastal plain. In all, 116 samples were recovered from seven boreholes drilled from 2-10 m a.s.l. to 16.5-26 m b.s.l. Microfossil assemblages, with special regard to benthic foraminifers and ostracods, were used to reconstruct the depositional palaeoenvironment. Fossil remains show that all the pre-79 AD fossiliferous sediments from 2 to - 24 m a.s.l. were deposited in shallow marine waters for a long time despite an appreciable sea level rise. The data indicate alternation of both shallow marine and subaerial conditions during the last ~ 15 kyr, evidencing ground uplift of the area of about 75 m at a rate of ~ 5 mm/year. Marine sediment accumulation (~ 6 m/kyr) and tectonic uplift long offset the sea level rise, and as a consequence, submerged areas remained the same as well.

Wind turbine pitch optimization

DEFF Research Database (Denmark)

Biegel, Benjamin; Juelsgaard, Morten; Stoustrup, Jakob

2011-01-01

for maximizing power production while simultaneously minimizing fatigue loads. In this paper, we show how this problem can be approximately solved using convex optimization. When there is full knowledge of the wind field, numerical simulations show that force and torque RMS variation can be reduced by over 96...

Warm-cold colonization: response of oaks to uplift of the Himalaya-Hengduan Mountains.

Science.gov (United States)

Meng, Hong-Hu; Su, Tao; Gao, Xiao-Yang; Li, Jie; Jiang, Xiao-Long; Sun, Hang; Zhou, Zhe-Kun

2017-06-01

Clarifying the relationship between distribution patterns of organisms and geological events is critical to understanding the impact of environmental changes on organismal evolution. Quercus sect. Heterobalanus is now distributed across the Himalaya-Hengduan Mountains (HHM) and warm lowland in East China, yet how the distribution patterns of this group changed in response to the HHM uplift remains largely unknown. This study examines the effect of tectonic events in the HHM region on the oaks, providing a biological perspective on the geological history of this region. Fifty-six populations of Quercus sect. Heterobalanus were genotyped using four chloroplast DNA regions and nine nuclear simple sequence repeat loci to assess population structure and diversity, supplemented by molecular dating and ancestral area reconstructions. The underlying demographic dynamics were compared using ecological niche models of the species distributions during the last glacial maximum and the present. These analyses illustrate that Quercus sect. Heterobalanus diversified as the HHM uplifted and climatic cooling during the mid-Miocene, colonizing the cold habitats from warm broadleaf mixed forests. Lineages in cold highlands and warm lowlands have diverged as a consequence of local adaptation to diverging climates since the late Miocene. Our results suggest that continuous uplift of the HHM in the late Miocene to early Pliocene accompanied by simultaneous cooling triggered the differentiation of oaks. The biogeography of Quercus sect. Heterobalanus illuminates the geological events responsible for the modern-day HHM. © 2017 John Wiley & Sons Ltd.

The topographic signature of Quaternary tectonic uplift in the Ardennes massif (Western Europe)

Science.gov (United States)

Sougnez, N.; Vanacker, V.

2011-04-01

Geomorphic processes that produce and transport sediment, and incise river valleys are complex; and often difficult to quantify over longer timescales of 103 to 105 y. Morphometric indices that describe the topography of hill slopes, valleys and river channels have commonly been used to compare morphological characteristics between catchments and to relate them to hydrological and erosion processes. This study aims to analyze the link between tectonic uplift rates and landscape morphology based on slope and channel morphometric indexes. To achieve this objective, we selected 10 catchments of about 150 to 250 km2 across the Ardennes Massif (a Palaeozoic massif of NW Europe, principally located in Belgium) that cover various tectonic domains with uplift rates ranging from about 0.06 to 0.20 mm yr-1 since mid-Pleistocene times. The morphometric analysis indicates that the slope and channel morphology of third-order catchments is not yet in topographic steady-state, and exhibits clear convexities in slope and river profiles. Our analysis indicates that the fluvial system is the main driver of topographic evolution and that the spatial pattern of uplift rates is reflected in the distribution of channel steepness and convexity. The spatial variation that we observe in slope and channel morphology between the 10 third-order catchments suggests that the response of the fluvial system was strongly diachronic, and that a transient signal of adjustment is migrating from the Meuse valley towards the Ardennian headwaters.

Incorporating geostrophic wind information for improved space–time short-term wind speed forecasting

KAUST Repository

Zhu, Xinxin

2014-09-01

Accurate short-term wind speed forecasting is needed for the rapid development and efficient operation of wind energy resources. This is, however, a very challenging problem. Although on the large scale, the wind speed is related to atmospheric pressure, temperature, and other meteorological variables, no improvement in forecasting accuracy was found by incorporating air pressure and temperature directly into an advanced space-time statistical forecasting model, the trigonometric direction diurnal (TDD) model. This paper proposes to incorporate the geostrophic wind as a new predictor in the TDD model. The geostrophic wind captures the physical relationship between wind and pressure through the observed approximate balance between the pressure gradient force and the Coriolis acceleration due to the Earth’s rotation. Based on our numerical experiments with data from West Texas, our new method produces more accurate forecasts than does the TDD model using air pressure and temperature for 1to 6-hour-ahead forecasts based on three different evaluation criteria. Furthermore, forecasting errors can be further reduced by using moving average hourly wind speeds to fit the diurnal pattern. For example, our new method obtains between 13.9% and 22.4% overall mean absolute error reduction relative to persistence in 2-hour-ahead forecasts, and between 5.3% and 8.2% reduction relative to the best previous space-time methods in this setting.

Determining the Probability of Violating Upper-Level Wind Constraints for the Launch of Minuteman III Ballistic Missiles at Vandenberg Air Force Base

Science.gov (United States)

Shafer, Jaclyn A.; Brock, Tyler M.

2012-01-01

The 30th Operational Support Squadron Weather Flight (30 OSSWF) provides comprehensive weather services to the space program at Vandenberg Air Force Base (VAFB) in California. One of their responsibilities is to monitor upper-level winds to ensure safe launch operations of the Minuteman Ill ballistic missile. The 30 OSSWF tasked the Applied Meteorology Unit (AMU) to analyze VAFB sounding data with the goal of determining the probability of violating (PoV) their upper-level thresholds for wind speed and shear constraints specific to this launch vehicle, and to develop a tool that will calculate the PoV of each constraint on the day of launch. In order to calculate the probability of exceeding each constraint, the AMU collected and analyzed historical data from VAFB. The historical sounding data were retrieved from the National Oceanic and Atmospheric Administration Earth System Research Laboratory archive for the years 1994-2011 and then stratified into four sub-seasons: January-March, April-June, July-September, and October-December. The AMU determined the theoretical distributions that best fit the maximum wind speed and maximum wind shear datasets and applied this information when calculating the averages and standard deviations needed for the historical and real-time PoV calculations. In addition, the AMU included forecast sounding data from the Rapid Refresh model. This information provides further insight for the launch weather officers (LWOs) when determining if a wind constraint violation will occur over the next few hours on the day of launch. The AMU developed an interactive graphical user interface (GUI) in Microsoft Excel using Visual Basic for Applications. The GUI displays the critical sounding data easily and quickly for LWOs on day of launch. This tool will replace the existing one used by the 30 OSSWF, assist the LWOs in determining the probability of exceeding specific wind threshold values, and help to improve the overall upper winds forecast for

Transient power coefficients for a two-blade Savonius wind turbine

Energy Technology Data Exchange (ETDEWEB)

Pope, K.; Naterer, G. [Univ. of Ontario Inst. of Technology, Oshawa, ON (Canada). Faculty of Engineering and Applied Science

2010-07-01

The wind power industry had a 29 percent growth rate in installed capacity in 2008, and technological advances are helping to speed up growth by significantly increasing wind turbine power yields. While the majority of the industry's growth has come from large horizontal axis wind turbine installations, small wind turbines can also be used in a wide variety of applications. This study predicted the transient power coefficient for a Savonius vertical axis wind turbine (VAWT) wind turbine with 2 blades. The turbine's flow field was used to analyze pressure distribution along the rotor blades in relation to the momentum, lift, and drag forces on the rotor surfaces. The integral force balance was used to predict the transient torque and power output of the turbine. The study examined the implications of the addition of a second blade on the model's ability to predict transient power outputs. Computational fluid dynamics (CFD) programs were used to verify that the formulation can be used to accurately predict the transient power coefficients of VAWTs with Savonius blades. 11 refs., 1 tab., 6 figs.

Exhumation of Basement-cored Uplifts: Example of the Kyrgyz Range Quantified with Apatite Fission-track Thermochronology

Science.gov (United States)

Sobel, Edward R.; Oskin, Michael; Burbank, Douglas; Mikolaichuk, Alexander

2005-01-01

The Kyrgyz Range, the northernmost portion of the Kyrgyzstan Tien Shan, displays topographic evidence for lateral propagation of surface uplift and exhumation. The highest and most deeply dissected segment lies in the center of the range. To the east, topography and relief decrease, and preserved remnants of a Cretaceous regional erosion surface imply minimal amounts of bedrock exhumation. The timing of exhumation of range segments defines the lateral propagation rate of the range-bounding reverse fault and quantifies the time and erosion depth needed to transform a mountain range from a juvenile to a mature morphology. New apatite fission-track (AFT) data from three transects from the eastern Kyrgyz Range, combined with published AFT data, demonstrate that the range has propagated over 110 km eastwards over the last 7-11 Myr. Based on the thermal and topographic evolutionary history, we present a model for a time-varying exhumation rate driven by rock uplift and changes in erodability and the time scale of geomorphic adjustment to surface uplift. Easily eroded, Cenozoic sedimentary rocks overlying resistant basement control early, rapid exhumation and slow surface upliftrates. As increasing amounts of resistant basement are exposed, exhumation rates decrease while surface uplift rates are sustained or increase, thereby growing topography. As the range becomes high enough to cause ice accumulation and develop steep river valleys, fluvial and glacial erosion become more powerful and exhumation rates once again increase. Independently determined range-noma1 shortening rates have also varied over time, suggesting a feedback between erosional efficiency and shortening rate.

Late Eocene Uplift of the Al Hajar Mountains, Oman, Supported by Stratigraphy and Low-Temperature Thermochronology

Science.gov (United States)

Hansman, Reuben J.; Ring, Uwe; Thomson, Stuart N.; den Brok, Bas; Stübner, Konstanze

2017-12-01

Uplift of the Al Hajar Mountains in Oman has been related to either Late Cretaceous ophiolite obduction or the Neogene Zagros collision. To test these hypotheses, the cooling of the central Al Hajar Mountains is constrained by 10 apatite (U-Th)/He (AHe), 15 fission track (AFT), and four zircon (U-Th)/He (ZHe) sample ages. These data show differential cooling between the two major structural culminations of the mountains. In the 3 km high Jabal Akhdar culmination AHe single-grain ages range between 39 ± 2 Ma and 10 ± 1 Ma (2σ errors), AFT ages range from 51 ± 8 Ma to 32 ± 4 Ma, and ZHe single-grain ages range from 62 ± 3 Ma to 39 ± 2 Ma. In the 2 km high Saih Hatat culmination AHe ages range from 26 ± 4 to 12 ± 4 Ma, AFT ages from 73 ± 19 Ma to 57 ± 8 Ma, and ZHe single-grain ages from 81 ± 4 Ma to 58 ± 3 Ma. Thermal modeling demonstrates that cooling associated with uplift and erosion initiated at 40 Ma, indicating that uplift occurred 30 Myr after ophiolite obduction and at least 10 Myr before the Zagros collision. Therefore, this uplift cannot be related to either event. We propose that crustal thickening supporting the topography of the Al Hajar Mountains was caused by a slowdown of Makran subduction and that north Oman took up the residual fraction of N-S convergence between Arabia and Eurasia.

Design of a novel and efficient lantern wind turbine

Science.gov (United States)

Ibrahim, M. D.; Wong, L. K.; Anyi, M.; Yunos, Y. S.; Rahman, M. R. A.; Mohta, M. Z.

2017-04-01

Wind turbine generates renewable energy when the forces acted on the turbine blades cause the rotation of the generator to produce clean electricity. This paper proposed a novel lantern wind turbine design compared to a conventional design model. Comparison is done based on simulation on coarse and fine meshing with all the results converged. Results showed that the pressure difference on the surface of novel design lantern wind turbine is much higher compared to the conventional wind turbine. Prototype is already manufactured and experimental result would be discussed in a separate future publication

Proceedings of a seminar on sea level displacement and bedrock uplift, 10-11 June 2010, Pori, Finland

International Nuclear Information System (INIS)

Lipping, T.; Ikonen, A.T.K.

2011-01-01

This working report is the proceedings of a seminar on Sea level displacement and bedrock uplift held on 10-11 June 2010 in Pori, Finland. The seminar included invited oral presentations, as well as poster presentations, addressing the causes and mechanisms, observations, modelling and implications of the sea level change and crustal uplift still continuing after the last glaciation in the Baltic Sea region. In the proceedings, a total of 14 papers are included, in addition to foreword and a summary of seminar discussions. (orig.)

Calculation and characteristics analysis of blade pitch loads for large scale wind turbines

Institute of Scientific and Technical Information of China (English)

无

2010-01-01

Based on the electric pitch system of large scale horizontal-axis wind turbines,the blade pitch loads coming mainly from centrifugal force,aerodynamic force and gravity are analyzed,and the calculation models for them are established in this paper.For illustration,a 1.2 MW wind turbine is introduced as a practical sample,and its blade pitch loads from centrifugal force,aerodynamic force and gravity are calculated and analyzed separately and synthetically.The research results showed that in the process of rotor rotating 360o,the fluctuation of blade pitch loads is similar to cosine curve when the rotor rotational speed,in-flow wind speed and pitch angle are constant.Furthermore,the amplitude of blade pitch load presents quite a difference at a different pitch angle.The ways of calculation for blade pitch loads are of the universality,and are helpful for further research of the individual pitch control system.

Numerical simulations of thermospheric dynamics: divergence as a proxy for vertical winds

Directory of Open Access Journals (Sweden)

S. L. Cooper

2009-06-01

Full Text Available A local scale, time dependent three-dimensional model of the neutral thermosphere was used to test the applicability of two previously published empirical relations between thermospheric vertical wind and velocity divergence, i.e., those due to Burnside et al. (1981 and Brekke (1997. The model self-consistently solves for vertical winds driven by heat and momentum deposited into the neutral atmosphere by high latitude ion convection. The Brekke condition accurately mimicked the overall "shape" of the three-dimensional model vertical wind field although, as written, it consistently overestimated the vertical wind magnitude by a factor of approximately 5/3, for the heating scenarios that we considered. This same general behavior was observed regardless of whether the forcing was static or rapidly changing with time. We discuss the likely reason for the Brekke condition overestimating the magnitude of our vertical winds, and suggest an alternative condition that should better describe vertical winds that are driven by local heating. The applicability of the Burnside condition was, by contrast, quite variable. During static heating, both the magnitude and the sign of the model vertical winds were predicted reliably at heights above those of maximum energy and momentum deposition per unit mass. However, below the thermal forcing, the Burnside condition predicted vertical winds of the wrong sign. It also introduced significant artefacts into the predicted vertical wind field when the forcing changed suddenly with time. If these results are of general applicability (which seems likely, given the way these relations are derived then the Burnside condition could usually be used safely at altitudes above h_mF₂. But it should be avoided below this height at all times, and even at high altitudes during periods of dynamic forcing. While the Brekke condition (or our modified version of it could likely be used in all circumstances

The interaction of prehistoric human settlement, sea level change and tectonic uplift of the Coastal Range, eastern Taiwan

Science.gov (United States)

Yang, H.; Chen, W. S.

2017-12-01

The late Cenozoic mountain belt of Taiwan, resulting from the collision between the Eurasian and Philippine Sea plates, is known for its rapid tectonic uplift. As postglacial sea level rose ca. 15,000 yr ago, the eastern coast of Taiwan, due to the rapid tectonic uplift rate, displayed a totally different scenario comparing with most of the coastal plains around the world. At the beginning of postglacial era, the sea level rising rate was greater than the tectonic uplift rate which induced the original piedmont alluvial fan or coastal plain to be overwhelmed by sea water rapidly. Around 13.5 ka, the tectonic uplift rate caught up with the sea level rising and broad wave-cut platform formed. The approximation of tectonic uplift and sea level rising rates was lasting from 13.5 to 5ka, but shoreline progradation may have been enhanced by increased slope erosion which resulted in the alluvial fan forming at the later time of this period. As soon as the eustasy stabilized, the landmass continued to uplift which might have enhanced the river incising and wave erosion rapidly. Therefore the topographic expression along the eastern fringing of Coastal Range forms extended alluvial-fan, stream, and marine terraces and are covered by late Holocene colluvium and marine deposits. 88 archaeological sites were chosen in this study based on surface survey where the archaeological chronology of cultural stage is established primarily through examining pottery series and associated manual excavation. It is interesting that most of the archaeological sites were located on the alluvial fan although the Holocene marine terraces have formed after 5ka. There are no clear evidences to support a shore-oriented settlement, but the abundant alluvial depositional structures observed from the overlaying formation reveals the stream depositional system was still active at this time. If the Neolithic people wanted to come to the "new born" coastal region for the abundant ocean resources, they

Model Engine Performance Measurement From Force Balance Instrumentation

Science.gov (United States)

Jeracki, Robert J.

1998-01-01

A large scale model representative of a low-noise, high bypass ratio turbofan engine was tested for acoustics and performance in the NASA Lewis 9- by 15-Foot Low-Speed Wind Tunnel. This test was part of NASA's continuing Advanced Subsonic Technology Noise Reduction Program. The low tip speed fan, nacelle, and an un-powered core passage (with core inlet guide vanes) were simulated. The fan blades and hub are mounted on a rotating thrust and torque balance. The nacelle, bypass duct stators, and core passage are attached to a six component force balance. The two balance forces, when corrected for internal pressure tares, measure the total thrust-minus-drag of the engine simulator. Corrected for scaling and other effects, it is basically the same force that the engine supports would feel, operating at similar conditions. A control volume is shown and discussed, identifying the various force components of the engine simulator thrust and definitions of net thrust. Several wind tunnel runs with nearly the same hardware installed are compared, to identify the repeatability of the measured thrust-minus-drag. Other wind tunnel runs, with hardware changes that affected fan performance, are compared to the baseline configuration, and the thrust and torque effects are shown. Finally, a thrust comparison between the force balance and nozzle gross thrust methods is shown, and both yield very similar results.

Retrieving hurricane wind speeds using cross-polarization C-band measurements

NARCIS (Netherlands)

Van Zadelhoff, G.J.; Stoffelen, A.; Vachon, P.W.; Wolfe, J.; Horstmann, J.; Belmonte Rivas, M.

2014-01-01

Hurricane-force wind speeds can have a large societal impact and in this paper microwave C-band cross-polarized (VH) signals are investigated to assess if they can be used to derive extreme wind-speed conditions. European satellite scatterometers have excellent hurricane penetration capability at

Mesoscale wind fluctuations over Danish waters

Energy Technology Data Exchange (ETDEWEB)

Vincent, C.L.

2010-12-15

mesoscale fluctuations in a mesoscale model is then examined using the weather research and forecasting (WRF) model. A set of case studies demonstrate that realistic hour-scale wind fluctuations and open cellular convection patterns develop in WRF simulations with 2 km horizontal grid spacing. The atmospheric conditions during one of the case studies are then used to initialise a simplified version of the model that has no large scale weather forcing, topography or surface inhomogeneties. Using the simplified model, the sensitivity of the modelled open cellular convection to choices in model setup and to aspects of the environmental forcing are tested. Finally, the cell-scale kinetic energy budget of the modelled cells is calculated, and it is shown that the buoyancy and pressure balance terms are important for cell maintenance. It is explained that the representation of mesoscale convection in a mesoscale model is not only important to end users such as wind farm operators, but to the treatment of energy transport within the boundary layer. (Author)

Mean and peak wind load reduction on heliostats

Energy Technology Data Exchange (ETDEWEB)

Peterka, J.A.; Tan, L.; Bienkiewcz, B.; Cermak, J.E.

1987-09-01

This report presents the results of wind-tunnel tests supported through the Solar Energy Research Institute (SERI) by the Office of Solar Thermal Technology of the US Department of Energy as part of the SERI research effort on innovative concentrators. As gravity loads on drive mechanisms are reduced through stretched-membrane technology, the wind-load contribution of the required drive capacity increases in percentage. Reduction of wind loads can provide economy in support structure and heliostat drive. Wind-tunnel tests have been directed at finding methods to reduce wind loads on heliostats. The tests investigated both mean and peak forces, and moments. A significant increase in ability to predict heliostat wind loads and their reduction within a heliostat field was achieved. In addition, a preliminary review of wind loads on parabolic dish collectors was conducted, resulting in a recommended research program for these type collectors. 42 refs., 38 figs., 1 tab.

Accidental inflation from Kaehler uplifting

Energy Technology Data Exchange (ETDEWEB)

Ben-Dayan, Ido; Westphal, Alexander; Wieck, Clemens [Deutsches Elektronen-Synchrotron DESY, Hamburg (Germany). Theory Group; Jing, Shenglin [Toronto Univ., ON (Canada). Canadian Inst. for Theoretical Astrophysics; Toronto Univ., ON (Canada). Dept. of Astronomy and Astrophysics

2013-09-15

We analyze the possibility of realizing inflation with a subsequent dS vacuum in the Kaehler uplifting scenario. The inclusion of several quantum corrections to the 4d effective action evades previous no-go theorems and allows for construction of simple and successful models of string inflation. The predictions of several benchmark models are in accord with current observations, i.e., a red spectral index, negligible non-gaussianity, and spectral distortions similar to the simplest models of inflation. A particularly interesting subclass of models are ''left-rolling'' ones, where the overall volume of the compactified dimensions shrinks during inflation. We call this phenomenon ''inflation by deflation'' (IBD), where deflation refers to the internal manifold. This subclass has the appealing features of being insensitive to initial conditions, avoiding the overshooting problem, and allowing for observable running {alpha}<{proportional_to}0.012 and enhanced tensor-to-scalar ratio r{proportional_to}10{sup -5}. The latter results differ significantly from many string inflation models.

Comparison of Ares I-X Wind-Tunnel Derived Buffet Environment with Flight Data

Science.gov (United States)

Piatak, David J.; Sekula, Martin K.; Rausch, Russ D.

2011-01-01

The Ares I-X Flight Test Vehicle (FTV), launched in October 2009, carried with it over 243 buffet verification pressure sensors and was one of the most heavily instrumented launch vehicle flight tests. This flight test represented a unique opportunity for NASA and its partners to compare the wind-tunnel derived buffet environment with that measured during the flight of Ares I-X. It is necessary to define the launch vehicle buffet loads to ensure that structural components and vehicle subsystems possess adequate strength, stress, and fatigue margins when the vehicle structural dynamic response to buffet forcing functions are considered. Ares I-X buffet forcing functions were obtained via wind-tunnel testing of a rigid buffet model (RBM) instrumented with hundreds of unsteady pressure transducers designed to measure the buffet environment across the desired frequency range. This paper discusses the comparison of RBM and FTV buffet environments, including fluctuating pressure coefficient and normalized sectional buffet forcing function root-mean-square magnitudes, frequency content of power-spectral density functions, and force magnitudes of an alternating flow phenomena. Comparison of wind-tunnel model and flight test vehicle buffet environments show very good agreement with root-mean-square magnitudes of buffet forcing functions at the majority of vehicle stations. Spectra proved a challenge to compare because of different wind-tunnel and flight test conditions and data acquisition rates. However, meaningful and promising comparisons of buffet spectra are presented. Lastly, the buffet loads resulting from the transition of subsonic separated flow to supersonic attached flow were significantly over-predicted by wind-tunnel results.

Southern Ocean carbon-wind stress feedback

Science.gov (United States)

Bronselaer, Ben; Zanna, Laure; Munday, David R.; Lowe, Jason

2018-02-01

The Southern Ocean is the largest sink of anthropogenic carbon in the present-day climate. Here, Southern Ocean pCO2 and its dependence on wind forcing are investigated using an equilibrium mixed layer carbon budget. This budget is used to derive an expression for Southern Ocean pCO2 sensitivity to wind stress. Southern Ocean pCO2 is found to vary as the square root of area-mean wind stress, arising from the dominance of vertical mixing over other processes such as lateral Ekman transport. The expression for pCO2 is validated using idealised coarse-resolution ocean numerical experiments. Additionally, we show that increased (decreased) stratification through surface warming reduces (increases) the sensitivity of the Southern Ocean pCO2 to wind stress. The scaling is then used to estimate the wind-stress induced changes of atmospheric pCO_2 in CMIP5 models using only a handful of parameters. The scaling is further used to model the anthropogenic carbon sink, showing a long-term reversal of the Southern Ocean sink for large wind stress strength.

The Characteristics on the Terrace and Uplift around the South-eastern part of Korean Peninsula for a Suitability of High level Radioactive Waste Disposal in Korea

International Nuclear Information System (INIS)

Koh, Yong Kwon; Bae, Dae Seok; Kim, Kyung Su; Kim, Geon Young; Park, Kyung Woo; Ji, Sung Hoon; Ryu, Ji Hoon

2009-08-01

The result of existing studies on the uplift in Korean peninsula would be regarded as high variety and rough uplifting range because of different approach method and various geologic formation with some location. As the results of this studies, the uplift around the southern part of Korean peninsula was estimated as the range from 0.0096mm to 1.4mm/year according to a geologic formation and location. It could be For the applying to HLW disposal project, the study on the uplift characteristics should be conducted according to the following guidelines: - should be a master program for the characterization of uplift in Korean peninsula considering long-term and systematic - should be applied scientific and quantitative approach methods and made subjective results - should be required an effective approach focused on limited area such as eastern, southern and western part of peninsula

Global sensitivity analysis in wind energy assessment

Science.gov (United States)

Tsvetkova, O.; Ouarda, T. B.

2012-12-01

Wind energy is one of the most promising renewable energy sources. Nevertheless, it is not yet a common source of energy, although there is enough wind potential to supply world's energy demand. One of the most prominent obstacles on the way of employing wind energy is the uncertainty associated with wind energy assessment. Global sensitivity analysis (SA) studies how the variation of input parameters in an abstract model effects the variation of the variable of interest or the output variable. It also provides ways to calculate explicit measures of importance of input variables (first order and total effect sensitivity indices) in regard to influence on the variation of the output variable. Two methods of determining the above mentioned indices were applied and compared: the brute force method and the best practice estimation procedure In this study a methodology for conducting global SA of wind energy assessment at a planning stage is proposed. Three sampling strategies which are a part of SA procedure were compared: sampling based on Sobol' sequences (SBSS), Latin hypercube sampling (LHS) and pseudo-random sampling (PRS). A case study of Masdar City, a showcase of sustainable living in the UAE, is used to exemplify application of the proposed methodology. Sources of uncertainty in wind energy assessment are very diverse. In the case study the following were identified as uncertain input parameters: the Weibull shape parameter, the Weibull scale parameter, availability of a wind turbine, lifetime of a turbine, air density, electrical losses, blade losses, ineffective time losses. Ineffective time losses are defined as losses during the time when the actual wind speed is lower than the cut-in speed or higher than the cut-out speed. The output variable in the case study is the lifetime energy production. Most influential factors for lifetime energy production are identified with the ranking of the total effect sensitivity indices. The results of the present

Rotor and wind turbine formalism

DEFF Research Database (Denmark)

Branlard, Emmanuel Simon Pierre

2017-01-01

The main conventions used in this book for the study of rotors are introduced in this chapter. The main assumptions and notations are provided. The formalism specific to wind turbines is presented. The forces, moments, velocities and dimensionless coefficients used in the study of rotors...

Stator for a rotating electrical machine having multiple control windings

Science.gov (United States)

Shah, Manoj R.; Lewandowski, Chad R.

2001-07-17

A rotating electric machine is provided which includes multiple independent control windings for compensating for rotor imbalances and for levitating/centering the rotor. The multiple independent control windings are placed at different axial locations along the rotor to oppose forces created by imbalances at different axial locations along the rotor. The multiple control windings can also be used to levitate/center the rotor with a relatively small magnetic field per unit area since the rotor and/or the main power winding provides the bias field.

Uplifting of the Jiamusi Block in the eastern Central Asian Orogenic Belt, NE China: evidence from basin provenance and geochronology

Science.gov (United States)

Liu, Yongjiang; Wen, Quanbo; Han, Guoqing; Li, Wei

2010-05-01

The main part of Jiamusi Block, named as Huanan-Uplift, is located in the northeastern Heilongjiang, China. The Huanan-Uplift is surrounded by many relatively small Mesozoic-Cenozoic basins, e.g. Sanjiang Basin, Hulin Basin, Boli Basin, Jixi Basin, Shuangyashan Basin and Shuanghua Basin. However previous research works were mainly focused on stratigraphy and palaeontology of the basins, therefore, the coupling relation between the uplift and the surrounding basins have not been clear. Based on the field investigations, conglomerate provenance studies of the Houshigou Formation in Boli Basin, geochronology of the Huanan-Uplift basement, we have been studied the relationships between Huanan-Uplift and the surrounding basins. The regional stratigraphic correlations indicates that the isolated basins in the area experienced the same evolution during the period of the Chengzihe and the Muling Formations (the Early Cretaceous). The paleogeography reconstructions suggest that the area had been a large-scale basin as a whole during the Early Cretaceous. The Huanan-Uplift did not exist. The paleocurrent directions, sandstone and conglomerate provenance analyses show that the Huanan-Uplift started to be the source area of the surrounding basins during the period of Houshigou Formation (early Late Cretaceous), therefore, it suggests that the Jiamusi Block commenced uplift in the early Late Cretaceous. The granitic gneisses in Huanan-Uplift give 494-415 Ma monazite U-Th-total Pb ages, 262-259 Ma biotite and 246-241 Ma K-feldspar 40Ar/39Ar ages. The cooling rates of 1-2 ℃/Ma from 500-260 Ma and 10-11 ℃/Ma from 260-240 Ma have been calculated based on the ages. This suggests that the Jiamusi Block had a rapid exhumation during late Permian, which should be related to the closure of the Paleo-Asian Ocean between the Siberian and North China continents. It is concluded that during the late Paleozoic the Jiamusi Block was stable with a very slow uplifting. With the closure of

The topographic signature of Quaternary tectonic uplift in the Ardennes massif (Western Europe

Directory of Open Access Journals (Sweden)

N. Sougnez

2011-04-01

Full Text Available Geomorphic processes that produce and transport sediment, and incise river valleys are complex; and often difficult to quantify over longer timescales of 10³ to 10⁵ y. Morphometric indices that describe the topography of hill slopes, valleys and river channels have commonly been used to compare morphological characteristics between catchments and to relate them to hydrological and erosion processes. This study aims to analyze the link between tectonic uplift rates and landscape morphology based on slope and channel morphometric indexes. To achieve this objective, we selected 10 catchments of about 150 to 250 km² across the Ardennes Massif (a Palaeozoic massif of NW Europe, principally located in Belgium that cover various tectonic domains with uplift rates ranging from about 0.06 to 0.20 mm yr⁻¹ since mid-Pleistocene times. The morphometric analysis indicates that the slope and channel morphology of third-order catchments is not yet in topographic steady-state, and exhibits clear convexities in slope and river profiles. Our analysis indicates that the fluvial system is the main driver of topographic evolution and that the spatial pattern of uplift rates is reflected in the distribution of channel steepness and convexity. The spatial variation that we observe in slope and channel morphology between the 10 third-order catchments suggests that the response of the fluvial system was strongly diachronic, and that a transient signal of adjustment is migrating from the Meuse valley towards the Ardennian headwaters.

Winds observed in the Northern European seas with wind lidars, meteorological masts and satellite

DEFF Research Database (Denmark)

Hasager, Charlotte Bay; Stein, D.; Peña, Alfredo

2013-01-01

Ocean winds have been observed in the Baltic, Irish and North Seas from a combination of groundbased lidars, tall offshore meteorological masts and satellites remote sensing in recent years. In the FP7 project NORSEWInD (2008-2012) the project partners joined forces to ensure collection of these ...

Feedback stabilization experiments using l = 2 equilibrium windings in Scyllac

International Nuclear Information System (INIS)

Bartsch, R.R.; Cantrell, E.L.; Gribble, R.F.; Freese, K.B.; Handy, L.E.; Kristal, R.; Miller, G.; Quinn, W.E.

1977-01-01

The confinement time in the Scyllac Sector Feedback Experiment has been extended with a pre-programmed equilibrium compensation force. This force was produced by driving a current with a flexible waveform in an additional set of l = 2 windings

Directionality Effects of Aligned Wind and Wave Loads on a Y-Shape Semi-Submersible Floating Wind Turbine under Rated Operational Conditions

Directory of Open Access Journals (Sweden)

Shengtao Zhou

2017-12-01

Full Text Available The Y-shape (triangular semi-submersible foundation has been adopted by most of the built full-scale floating wind turbines, such as Windfloat, Fukushima Mirai and Shimpuu. Considering the non-fully-symmetrical shape and met-ocean condition, the foundation laying angle relative to wind/wave directions will not only influence the downtime and power efficiency of the floating turbine, but also the strength and fatigue safety of the whole structure. However, the dynamic responses induced by various aligned wind and wave load directions have scarcely been investigated comparatively before. In our study, the directionality effects are investigated by means of combined wind and wave tests and coupled multi-body simulations. By comparing the measured data in three load directions, it is found that the differences of platform motions are mainly derived from the wave loads and larger pitch motion can always be observed in one of the directions. To make certain the mechanism underlying the observed phenomena, a coupled multi-body dynamic model of the floating wind turbine is established and validated. The numerical results demonstrate that the second-order hydrodynamic forces contribute greatly to the directionality distinctions for surge and pitch, and the first-order hydrodynamic forces determine the variations of tower base bending moments and nacelle accelerations. These findings indicate the directionality effects should be predetermined comprehensively before installation at sea, which is important for the operation and maintenance of the Y-shape floating wind turbines.

Changes in Surface Wind Speed over North America from CMIP5 Model Projections and Implications for Wind Energy

Directory of Open Access Journals (Sweden)

Sujay Kulkarni

2014-01-01

Full Text Available The centennial trends in the surface wind speed over North America are deduced from global climate model simulations in the Climate Model Intercomparison Project—Phase 5 (CMIP5 archive. Using the 21st century simulations under the RCP 8.5 scenario of greenhouse gas emissions, 5–10 percent increases per century in the 10 m wind speed are found over Central and East-Central United States, the Californian Coast, and the South and East Coasts of the USA in winter. In summer, climate models projected decreases in the wind speed ranging from 5 to 10 percent per century over the same coastal regions. These projected changes in the surface wind speed are moderate and imply that the current estimate of wind power potential for North America based on present-day climatology will not be significantly changed by the greenhouse gas forcing in the coming decades.

Modelling the impact of regional uplift and local tectonics on fluvial terrace preservation.

NARCIS (Netherlands)

Viveen, W.; Schoorl, J.M.; Veldkamp, A.; Balen, van R.T.

2014-01-01

A terrace formation model (TERRACE) combined with a longitudinal river profile model (FLUVER) was used to simulate fluvial terrace formation and preservation in the northwest Iberian lower Miño River basin under the influence of three tectonic conditions; namely regional vertical uplift, local basin

Role of sea surface wind stress forcing on transport between Tropical Pacific and Indian Ocean

Science.gov (United States)

Zhao, Q.

Using an Indian-Pacific Ocean Circulation Model (IPOM) a simulation study on the Transports of between Tropical Pacific and Indian Ocean such as Indonesian Through flow (ITF) has been done. IPOM covered the area 25°E-70°W, 35°S-60°N. There are 31 levels in the vertical with 22 levels upper 400m in it. The horizontal resolution is 1/3° lat x 1.5° lon between 10°S and 10°N. The coastline and ocean topography of IPOM is prepared from Scripps topography data on 1x1°grid. Forcing IPOM with monthly observational wind stress in 1990-1999 the interannual variation of sea temperature has been reproduced well, not only on El Nino in the Pacific but also on Indian Ocean Dipole (IOD). Therefore, the oceanic circulations in the tropical ocean are reasonable. The analyses of the oceanic circulations from the simulations suggest that the transport southward through Makassar Strait is the primary route of thermocline water masses from the North Pacific to the Indonesian sea. The transport westward through Bali-Western Australian Transect (BWAT, at 117.5E) can be thought as the final output of ITF through the archipelago to Indian Ocean. The transport westward through BWAT is in 8-12S above 150m, its core centered near surface 10S, which looks like a jet. The westward velocity is more than 50 cm/s. The transport shows significant seasonal and interannual variations. The maximum is in Jul-Oct, minimum in Jan-Mar. These results are consistent with some observation basically. The correlation analyses indict that the variations of transport westward is related with the southeasterly anomaly in the east tropical Indian ocean. The transport variation lags wind anomaly about 3 months. The correlation coefficient is more than 0.6. The transport is strong during IOD, for example in 1994 and 1997. The variations are also related with the northwesterly anomaly in the center equatorial Pacific and the easterly in the eastern equatorial Pacific. The transport is strong in most ENSO

Evaluation of Offshore Wind Turbine Tower Dynamics with Numerical Analysis

Directory of Open Access Journals (Sweden)

Begum Yurdanur Dagli

2018-01-01

Full Text Available A dynamic behaviour of a cylindirical wind tower with variable cross section is investigated under environmental and earthquake forces. The ground acceleration term is represented by a simple cosine function to investigate both normal and parallel components of the earthquake motions located near ground surface. The function of earthquake force is simplified to apply Rayleigh’s energy method. Wind forces acting on above the water level and wave forces acting on below this level are utilized in computations considering earthquake effect for entire structure. The wind force is divided into two groups: the force acting on the tower and the forces acting on the rotor nacelle assembly (RNA. The drag and the inertial wave forces are calculated with water particle velocities and accelerations due to linear wave theory. The resulting hydrodynamic wave force on the tower in an unsteady viscous flow is determined using the Morison equation. The displacement function of the physical system in which dynamic analysis is performed by Rayleigh’s energy method is obtained by the single degree of freedom (SDOF model. The equation of motion is solved by the fourth-order Runge–Kutta method. The two-way FSI (fluid-structure interaction technique was used to determine the accuracy of the numerical analysis. The results of computational fluid dynamics and structural mechanics are coupled in FSI analysis by using ANSYS software. Time-varying lateral displacements and the first natural frequency values which are obtained from Rayleigh’s energy method and FSI technique are compared. The results are presented by graphs. It is observed from these graphs that the Rayleigh model can be an alternative way at the prelimanary stage of the structural analysis with acceptable accuracy.

Identification of wind fields for wave modeling near Qatar

Science.gov (United States)

Nayak, Sashikant; Balan Sobhana, Sandeepan; Panchang, Vijay

2016-04-01

Due to the development of coastal and offshore infrastructure in and around the Arabian Gulf, a large semi-enclosed sea, knowledge of met-ocean factors like prevailing wind systems, wind generated waves, and currents etc. are of great importance. Primarily it is important to identify the wind fields that are used as forcing functions for wave and circulation models for hindcasting and forecasting purposes. The present study investigates the effects of using two sources of wind-fields on the modeling of wind-waves in the Arabian Gulf, in particular near the coastal regions of Qatar. Two wind sources are considered here, those obtained from ECMWF and those generated by us using the WRF model. The wave model SWAN was first forced with the 6 hourly ERA Interim daily winds (from ECMWF) having spatial resolution of 0.125°. For the second option, wind fields were generated by us using the mesoscale wind model (WRF) with a high spatial resolution (0.1°) at every 30 minute intervals. The simulations were carried out for a period of two months (7th October-7th December, 2015) during which measurements were available from two moored buoys (deployed and operated by the Qatar Meteorological Department), one in the north of Qatar ("Qatar North", in water depth of 58.7 m) and other in the south ("Shiraouh Island", in water depth of 16.64 m). This period included a high-sea event on 11-12th of October, recorded by the two buoys where the significant wave heights (Hs) reached as high as 2.9 m (i.e. max wave height H ~ 5.22 m) and 1.9 (max wave height H ~ 3.4 m) respectively. Model results were compared with the data for this period. The scatter index (SI) of the Hs simulated using the WRF wind fields and the observed Hs was found to be about 30% and 32% for the two buoys (total period). The observed Hs were generally reproduced but there was consistent underestimation. (Maximum 27% for the high-sea event). For the Hs obtained with ERA interim wind fields, the underestimation was

Tectonics, orbital forcing, global climate change, and human evolution in Africa: introduction to the African paleoclimate special volume.

Science.gov (United States)

Maslin, Mark A; Christensen, Beth

2007-11-01

The late Cenozoic climate of Africa is a critical component for understanding human evolution. African climate is controlled by major tectonic changes, global climate transitions, and local variations in orbital forcing. We introduce the special African Paleoclimate Issue of the Journal of Human Evolution by providing a background for and synthesis of the latest work relating to the environmental context for human evolution. Records presented in this special issue suggest that the regional tectonics, appearance of C(4) plants in East Africa, and late Cenozoic global cooling combined to produce a long-term drying trend in East Africa. Of particular importance is the uplift associated with the East African Rift Valley formation, which altered wind flow patterns from a more zonal to more meridinal direction. Results in this volume suggest a marked difference in the climate history of southern and eastern Africa, though both are clearly influenced by the major global climate thresholds crossed in the last 3 million years. Papers in this volume present lake, speleothem, and marine paleoclimate records showing that the East African long-term drying trend is punctuated by episodes of short, alternating periods of extreme wetness and aridity. These periods of extreme climate variability are characterized by the precession-forced appearance and disappearance of large, deep lakes in the East African Rift Valley and paralleled by low and high wind-driven dust loads reaching the adjacent ocean basins. Dating of these records show that over the last 3 million years such periods only occur at the times of major global climatic transitions, such as the intensification of Northern Hemisphere Glaciation (2.7-2.5 Ma), intensification of the Walker Circulation (1.9-1.7 Ma), and the Mid-Pleistocene Revolution (1-0.7 Ma). Authors in this volume suggest this onset occurs as high latitude forcing in both Hemispheres compresses the Intertropical Convergence Zone so that East Africa

Tectonic and erosion-driven uplift for the Gamburtsev Mountains: a preliminary combined landscape analyses and flexural modelling approach

Science.gov (United States)

Ferraccioli, Fausto; Anderson, Lester; Jamieson, Stewart; Bell, Robin; Rose, Kathryn; Jordan, Tom; Finn, Carol; Damaske, Detlef

2013-04-01

Mountain building processes in intraplate settings remain relatively poorly understood when compared to ranges formed along plate margins. The most enigmatic intraplate mountain range on Earth is located in the middle of the East Antarctic Craton and is known from geophysical surveys as the Gamburtsev Subglacial Mountains (GSM). During the IPY, the AGAP project acquired 120,000 line km of airborne geophysical data (Bell et al., 2011, Science) and seismological observations (Hansen et al., 2010, EPSL) across central East Antarctica that provide new perspectives on crustal architecture and uplift mechanisms for the enigmatic GSM (Ferraccioli et al., 2011, Nature). The geophysical data define a 2,500-km-long Paleozoic-Mesozoic rift system in East Antarctica surrounding the GSM. A thick high-density lower crustal root is in parts preserved beneath the range and has been interpreted as having formed during Proterozoic assembly of a mosaic of originally separate East Antarctic provinces. Rifting could have triggered phase/density changes at deep crustal levels, effectively restoring some of the latent root buoyancy, as well as causing more classical flexural rift-flank uplift. Permian rifting was followed by Cretaceous strike-slip faulting and transtension associated with Gondwana break-up and this phase may have provided a more recent tectonic trigger for initial uplift of the modern GSM. The Cretaceous rift-flank uplift model for the Gamburtsevs is appealing because it relates the initiation of intraplate mountain-building to larger-scale geodynamic processes and is consistent with several geological and geophysical interpretations in the adjacent Lambert Rift (Ferraccioli et al., 2011). However, a more recent interpretation predicts that major Cretaceous rift-related exhumation in interior East Antarctica is not required to explain detrital thermochrology results from Oligocene-Quaternary sediments in Prydz Bay (Tochlin et al., 2012, G3). This raises the question of

Wind turbine spoiler

Science.gov (United States)

Sullivan, W.N.

An aerodynamic spoiler system for a vertical axis wind turbine includes spoilers on the blades initially stored near the rotor axis to minimize drag. A solenoid latch adjacent the central support tower releases the spoilers and centrifugal force causes the spoilers to move up the turbine blades away from the rotor axis, thereby producing a braking effect and actual slowing of the associated wind turbine, if desired. The spoiler system can also be used as an infinitely variable power control by regulated movement of the spoilers on the blades over the range between the undeployed and fully deployed positions. This is done by the use of a suitable powered reel and cable located at the rotor tower to move the spoilers.

Wind Powering America FY07 Activities Summary

Energy Technology Data Exchange (ETDEWEB)

2008-02-01

The Wind Powering America FY07 Activities Summary reflects the accomplishments of our state wind working groups, our programs at the National Renewable Energy Laboratory, and our partner organizations. The national WPA team remains a leading force for moving wind energy forward in the United States. WPA continues to work with its national, regional, and state partners to communicate the opportunities and benefits of wind energy to a diverse set of stakeholders. WPA now has 30 state wind working groups (welcoming Georgia and Wisconsin in 2007) that form strategic alliances to communicate wind's benefits to the state stakeholders. More than 140 members of national and state public and private sector organizations from 39 U.S. states and Canada attended the 6th Annual WPA All-States Summit in Los Angeles in June. WPA's emphasis remains on the rural agricultural sector, which stands to reap the significant economic development benefits of wind energy development. Additionally, WPA continues its program of outreach, education, and technical assistance to Native American communities, public power entities, and regulatory and legislative bodies.

Turbulent Structure Under Short Fetch Wind Waves

Science.gov (United States)

2015-12-01

maximum 200 words ) Momentum transfer from wind forcing into the ocean is complicated by the presence of surface waves. Wind momentum and energy are...1,520 m from the mouth of the river to the deployment site ). Map created in Google Earth, October 12, 2015, http://www.google.com/earth/. 33...Doppler processing electronics for each transducer uses 14 bit analog to digital converter to digitize the 1.2 MHz acoustic frequency from the four

Pulsar Magnetohydrodynamic Winds

Science.gov (United States)

Okamoto, Isao; Sigalo, Friday B.

2006-12-01

The acceleration and collimation/decollimation of relativistic magnetocentrifugal winds are discussed concerning a cold plasma from a strongly magnetized, rapidly rotating neutron star in a steady axisymmetric state based on ideal magnetohydrodynamics. There exist unipolar inductors associated with the field line angular frequency, α, at the magnetospheric base surface, SB, with a huge potential difference between the poles and the equator, which drive electric current through the pulsar magnetosphere. Any ``current line'' must emanate from one terminal of the unipolar inductor and return to the other, converting the Poynting flux to the kinetic flux of the wind at finite distances. In a plausible field structure satisfying the transfield force-balance equation, the fast surface, SF, must exist somewhere between the subasymptotic and asymptotic domains, i.e., at the innermost point along each field line of the asymptotic domain of \\varpaA2/\\varpi2 ≪ 1, where \\varpiA is the Alfvénic axial distance. The criticality condition at SF yields the Lorentz factor, γF = μ\\varepsilon1/3, and the angular momentum flux, β, as the eigenvalues in terms of the field line angular velocity, α, the mass flux per unit flux tube, η, and one of the Bernoulli integrals, μδ, which are assumed to be specifiable as the boundary conditions at SB. The other Bernoulli integral, μɛ, is related to μδ as μɛ = μδ[1-(α2\\varpiA2/c2)]-1, and both μɛ and \\varpiA2 are eigenvalues to be determined by the criticality condition at SF. Ongoing MHD acceleration is possible in the superfast domain. This fact may be helpful in resolving a discrepancy between the wind theory and the Crab-nebula model. It is argued that the ``anti-collimation theorem'' holds for relativistic winds, based on the curvature of field streamlines determined by the transfield force balance. The ``theorem'' combines with the ``current-closure condition'' as a global condition in the wind zone to produce a

Role of erosion and isostasy in the Cordillera Blanca uplift: insights from Low-T thermochronology and landscape evolution modeling (northern Peru, Andes)

Science.gov (United States)

Margirier, A.; Robert, X.; Braun, J.; Laurence, A.

2017-12-01

The uplift and exhumation of the highest Peruvian peaks seems closely linked to the Cordillera Blanca normal fault that delimits and shape the western flank of the Cordillera Blanca. Two models have been previously proposed to explain the occurrence of extension and the presence of this active normal fault in a compression setting but the Cordillera Blanca normal fault and the uplift and exhumation of the Cordillera Blanca remain enigmatic. Recent studies suggested an increase of exhumation rates during the Quaternary in the Cordillera Blanca and related this increase to a change in climate and erosion process (glacial erosion vs. fluvial erosion). The Cordillera Blanca granite has been significantly eroded since its emplacement (12-5 Ma) indicating a significant mass of rocks removal. Whereas it has been demonstrated recently that the effect of eroding denser rocks can contribute to an increase of uplift rate, the impact of erosion and isostasy on the increase of the Cordillera Blanca uplift rates has never been explored. Based on numerical modeling of landscape evolution we address the role of erosion and isostasy in the uplift and exhumation of the Cordillera Blanca. We performed inversions of the present-day topography, total exhumation and thermochronological data using a landscape evolution model (FastScape). Our results evidence the contribution of erosion and associated flexural rebound to the uplift of the Cordillera Blanca. Our models suggest that the erosion of the Cordillera Blanca dense intrusion since 3 Ma could also explain the Quaternary exhumation rate increase in this area. Finally, our results allow to question the previous models proposed for the formation of the Cordillera Blanca normal fault.

Caregiving burden and uplifts: a contradiction or a protective partnership for the quality of life of parents and their children with asthma?

Science.gov (United States)

Silva, Neuza; Carona, Carlos; Crespo, Carla; Canavarro, Maria Cristina

2015-04-01

Parental caregiving in the context of pediatric chronic conditions is a multifaceted experience that encompasses negative (burdens) and positive dimensions (uplifts), which may support risk and protective processes that influence family adaptation. This study aimed to examine the caregiving experience of parents caring for a child with asthma and the moderating role of caregiving uplifts on the associations between caregiving burden and quality of life (QoL) of parents and their children. Participants were 180 dyads of children/adolescents with asthma between 8 and 18 years of age and one of their parents. The parents reported on caregiving burden and uplifts and on their QoL, and the children/adolescents completed a self-report measure of generic QoL. Results showed that although parents of children with intermittent asthma and parents of younger children presented higher levels of caregiving burden, noncontrolled asthma was the only clinical variable representing a significant risk factor for decreased QoL in children. Significant negative and positive associations were found between burden dimensions and QoL and between caregiving uplifts and QoL, respectively, in parents and children. Additionally, caregiving uplifts moderated the negative link between relationship burden and parents' QoL. These results suggest that, far from being contradictory, caregiving uplifts may co-occur with high levels of burden and may constitute a protective factor against the deleterious effect of the caregiving burden on parents' QoL and a resource that directly contributes to children's QoL. This risk-resistance approach to family caregiving may contribute to operationalizing strength-based interventions in the context of pediatric asthma. (c) 2015 APA, all rights reserved).

Formation of intrathermocline eddies at ocean fronts by wind-driven destruction of potential vorticity

Science.gov (United States)

Thomas, Leif N.

2008-08-01

A mechanism for the generation of intrathermocline eddies (ITEs) at wind-forced fronts is examined using a high resolution numerical simulation. Favorable conditions for ITE formation result at fronts forced by "down-front" winds, i.e. winds blowing in the direction of the frontal jet. Down-front winds exert frictional forces that reduce the potential vorticity (PV) within the surface boundary in the frontal outcrop, providing a source for the low-PV water that is the materia prima of ITEs. Meandering of the front drives vertical motions that subduct the low-PV water into the pycnocline, pooling it into the coherent anticyclonic vortex of a submesoscale ITE. As the fluid is subducted along the outcropping frontal isopycnal, the low-PV water, which at the surface is associated with strongly baroclinic flow, re-expresses itself as water with nearly zero absolute vorticity. This generation of strong anticyclonic vorticity results from the tilting of the horizontal vorticity of the frontal jet, not from vortex squashing. During the formation of the ITE, high-PV water from the pycnocline is upwelled alongside the subducting low-PV surface water. The positive correlation between the ITE's velocity and PV fields results in an upward, along-isopycnal eddy PV flux that scales with the surface frictional PV flux driven by the wind. The relationship between the eddy and wind-induced frictional PV flux is nonlocal in time, as the eddy PV flux persists long after the wind forcing is shut off. The ITE's PV flux affects the large-scale flow by driving an eddy-induced transport or bolus velocity down the outcropping isopycnal layer with a magnitude that scales with the Ekman velocity.

The Analysis and Comparison of Leakage Inductance in Different Winding Arrangements for Planar Transformer

DEFF Research Database (Denmark)

Ouyang, Ziwei; Thomsen, Ole Cornelius; Andersen, Michael Andreas E.

2009-01-01

The coupling of the windings can be easily increased by using multiply stacked planar windings connection. Interleaving is a well-known technique used to reduce leakage inductance and minimize high-frequency winding losses. The paper aims to analyze leakage inductance based on magneto motive force...

Paleokarst on the top of the Maokou Formation: Further evidence for domal crustal uplift prior to the Emeishan flood volcanism

Science.gov (United States)

He, Bin; Xu, Yi-Gang; Guan, Jun-Peng; Zhong, Yu-Ting

2010-09-01

The ~ 260 Ma Emeishan Large Igneous Province (ELIP) in southwest China has previously been demonstrated to provide compelling evidence for pre-volcanic crustal doming in support of the mantle plume hypothesis. However this has been questioned by Ukstins-Peate and Bryan (2008) by showing hydrothermal magmatic activity at the Daqiao section. To solve this argument, a detailed characterization of the contact between the Emeishan basalts and the Maokou Formation was carried out. The contact is shown to be an unconformity, which is characterized by paleokarst on top of the Maokou Formation, including paleokarst relief, sinkholes, caves, tower karst and its corresponding rocks (such as kaolinite, bauxite and ferruginous duricrust and collapsed breccias, etc.). This paleokarst unconformity was in turn covered or infilled by the Emeishan basalts and tuffs, suggesting that uplift and erosion occurred prior to the eruption of the ELIP. The extent of erosion of the Maokou Formation indicates the ELIP can be divided into three roughly concentric zones: the inner, intermediate, and outer zones. The paleokarst features on the top of Maokou Formation vary across the ELIP. In the inner zone, a likely sinkhole and an incision valley with 450 m relief in height are found. In the intermediate zone, various paleokarst landforms such as karst relief, sinkholes and tower karsts are well developed. Some sinkholes that developed in the Qixia Formation below the Maokou Formation imply that the paleorelief is more than 350 m in height. In the outer zone, the paleokarstic surface is a paleo-weathering layer with minor karstification and development of caves at 10-50 m. This spatial variation of the paleokarst reflects variation of uplift height across the ELIP. The extent of minimal uplift is estimated to be at least 450 m in the inner zone, 350 m in the intermediate zone, whereas uplift is minor (tens-50 m) in the outer zone. The magnitude and shape of the uplift is roughly consistent with

Influence of orographically steered winds on Mutsu Bay surface currents

Science.gov (United States)

Yamaguchi, Satoshi; Kawamura, Hiroshi

2005-09-01

Effects of spatially dependent sea surface wind field on currents in Mutsu Bay, which is located at the northern end of Japanese Honshu Island, are investigated using winds derived from synthetic aperture radar (SAR) images and a numerical model. A characteristic wind pattern over the bay was evidenced from analysis of 118 SAR images and coincided with in situ observations. Wind is topographically steered with easterly winds entering the bay through the terrestrial gap and stronger wind blowing over the central water toward its mouth. Nearshore winds are weaker due to terrestrial blockages. Using the Princeton Ocean Model, we investigated currents forced by the observed spatially dependent wind field. The predicted current pattern agrees well with available observations. For a uniform wind field of equal magnitude and average direction, the circulation pattern departs from observations demonstrating that vorticity input due to spatially dependent wind stress is essential in generation of the wind-driven current in Mutsu Bay.

Full non-linear treatment of the global thermospheric wind system. I - Mathematical method and analysis of forces. II - Results and comparison with observations

Science.gov (United States)

Blum, P. W.; Harris, I.

1975-01-01

The equations of horizontal motion of the neutral atmosphere between 120 and 500 km are integrated with the inclusion of all nonlinear terms of the convective derivative and the viscous forces due to vertical and horizontal velocity gradients. Empirical models of the distribution of neutral and charged particles are assumed to be known. The model of velocities developed is a steady state model. In Part I the mathematical method used in the integration of the Navier-Stokes equations is described and the various forces are analyzed. Results of the method given in Part I are presented with comparison with previous calculations and observations of upper atmospheric winds. Conclusions are that nonlinear effects are only significant in the equatorial region, especially at solstice conditions and that nonlinear effects do not produce any superrotation.

Prospects for generating electricity by large onshore and offshore wind farms

DEFF Research Database (Denmark)

Volker, Patrick; Hahmann, Andrea N.; Badger, Jake

2017-01-01

large wind farms, winds can decrease considerably from their free-stream values to a point where an equilibrium wind speed is reached. The magnitude of this equilibrium wind speed is primarily dependent on the balance between turbine drag force and the downward momentum influx from above the wind farm......The decarbonisation of energy sources requires additional investments in renewable technologies, including the installation of onshore and offshore wind farms. For wind energy to remain competitive, wind farms must continue to provide low-cost power even when covering larger areas. Inside very...... on the local free-stream wind speed, the surface characteristics, and the turbine density. In onshore regions with moderate winds the power density of very large wind farms reaches 1 W m−2, whereas in offshore regions with very strong winds it exceeds 3 W m−2. Despite a relatively low power density, onshore...

Natural Ventilation Driven by Wind and Temperature Difference

DEFF Research Database (Denmark)

Larsen, Tine Steen

Natural ventilation is a commonly used principle when buildings are being ventilated. It can be controlled by openings in the building envelope, which open or close depending on the need of air inside the building. It can also be the simple action of just opening a door or a window to let the fresh...... driving forces are still wind pressure and temperature differences as with cross-ventilation, but here the turbulence in the wind and the pulsating flow near the opening also affect the flow through the opening. From earlier work, some design expressions already exist, but none of these include...... the incidence angle of the wind, which is an important parameter in this type of ventilation. Several wind tunnel experiments are made and from the results of these, a new design expression is made which includes the wind pressure, temperature difference, incidence angle of the wind and the fluctuations...

Aeroelastic analysis of large horizontal wind turbine baldes?

Institute of Scientific and Technical Information of China (English)

Di TANG; Zhiliang LU; Tongqing GUO

2016-01-01

A nonlinear aeroelastic analysis method for large horizontal wind turbines is described. A vortex wake method and a nonlinear ?nite element method (FEM) are coupled in the approach. The vortex wake method is used to predict wind turbine aero-dynamic loads of a wind turbine, and a three-dimensional (3D) shell model is built for the rotor. Average aerodynamic forces along the azimuth are applied to the structural model, and the nonlinear static aeroelastic behaviors are computed. The wind rotor modes are obtained at the static aeroelastic status by linearizing the coupled equations. The static aeroelastic performance and dynamic aeroelastic responses are calculated for the NH1500 wind turbine. The results show that structural geometrical nonlinearities signi?cantly reduce displacements and vibration amplitudes of the wind turbine blades. Therefore, structural geometrical nonlinearities cannot be neglected both in the static aeroelastic analysis and dynamic aeroelastic analysis.

Late Quaternary uplift rate inferred from marine terraces, Muroto Peninsula, southwest Japan: Forearc deformation in an oblique subduction zone

Science.gov (United States)

Matsu'ura, Tabito

2015-04-01

Tectonic uplift rates across the Muroto Peninsula, in the southwest Japan forearc (the overriding plate in the southwest Japan oblique subduction zone), were estimated by mapping the elevations of the inner edges of marine terrace surfaces. The uplift rates inferred from marine terraces M1 and M2, which were correlated by tephrochronology with marine isotope stages (MIS) 5e and 5c, respectively, include some vertical offset by local faults but generally decrease northwestward from 1.2-1.6 m ky- 1 on Cape Muroto to 0.3-0.7 m ky- 1 in the Kochi Plain. The vertical deformation of the Muroto Peninsula since MIS 5e and 5c was interpreted as a combination of regional uplift and folding related to the arc-normal offshore Muroto-Misaki fault. A regional uplift rate of 0.46 m ky- 1 was estimated from terraces on the Muroto Peninsula, and the residual deformation of these terraces was attributed to fault-related folding. A mass-balance calculation yielded a shortening rate of 0.71-0.77 m ky- 1 for the Muroto Peninsula, with the Muroto-Misaki fault accounting for 0.60-0.71 m ky- 1, but these rates may be overestimated by as much as 10% given variations of several meters in the elevation difference between the buried shoreline angles and terrace inner edges in the study area. A thrust fault model with flat (5-10° dip) and ramp (60° dip) components is proposed to explain the shortening rate and uplift rate of the Muroto-Misaki fault since MIS 5e. Bedrock deformation also indicates that the northern extension of this fault corresponds to the older Muroto Flexure.

X-band COSMO-SkyMed wind field retrieval, with application to coastal circulation modeling

Directory of Open Access Journals (Sweden)

A. Montuori

2013-02-01

Full Text Available In this paper, X-band COSMO-SkyMed^© synthetic aperture radar (SAR wind field retrieval is investigated, and the obtained data are used to force a coastal ocean circulation model. The SAR data set consists of 60 X-band Level 1B Multi-Look Ground Detected ScanSAR Huge Region COSMO-SkyMed^© SAR data, gathered in the southern Tyrrhenian Sea during the summer and winter seasons of 2010. The SAR-based wind vector field estimation is accomplished by resolving both the SAR-based wind speed and wind direction retrieval problems independently. The sea surface wind speed is retrieved by means of a SAR wind speed algorithm based on the azimuth cut-off procedure, while the sea surface wind direction is provided by means of a SAR wind direction algorithm based on the discrete wavelet transform multi-resolution analysis. The obtained wind fields are compared with ground truth data provided by both ASCAT scatterometer and ECMWF model wind fields. SAR-derived wind vector fields and ECMWF model wind data are used to construct a blended wind product regularly sampled in both space and time, which is then used to force a coastal circulation model of a southern Tyrrhenian coastal area to simulate wind-driven circulation processes. The modeling results show that X-band COSMO-SkyMed^© SAR data can be valuable in providing effective wind fields for coastal circulation modeling.

Golf in the Wind: Exploring the Effect of Wind on the Accuracy of Golf Shots

Science.gov (United States)

Yaghoobian, Neda; Mittal, Rajat

2015-11-01

Golf play is highly dependent on the weather conditions with wind being the most significant factor in the unpredictability of the ball landing position. The direction and strength of the wind alters the aerodynamic forces on a ball in flight, and consequently its speed, distance and direction of travel. The fact that local wind conditions on any particular hole change over times-scales ranging all the way from a few seconds to minutes, hours and days introduces an element of variability in the ball trajectory that is not understood. Any such analysis is complicated by the effect of the local terrestrial and vegetation topology, as well as the inherent complexity of golf-ball aerodynamics. In the current study, we use computational modeling to examine the unpredictability of the shots under different wind conditions over Hole-12 at the Augusta National Golf Club, where the Masters Golf Tournament takes place every year. Despite this being the shortest hole on the course, the presence of complex vegetation canopy around this hole introduces a spatial and temporal variability in wind conditions that evokes uncertainty and even fear among professional golfers. We use our model to examine the effect of wind direction and wind-speed on the accuracy of the golf shots at this hole and use the simulations to determine the key aerodynamic factors that affect the accuracy of the shot.

Relative contributions of external forcing factors to circulation and hydrographic properties in a micro-tidal bay

Science.gov (United States)

Yoon, Seokjin; Kasai, Akihide

2017-11-01

The dominant external forcing factors influencing estuarine circulation differ among coastal environments. A three-dimensional regional circulation model was developed to estimate external influence indices and relative contributions of external forcing factors such as external oceanic forcing, surface heat flux, wind stress, and river discharge to circulation and hydrographic properties in Tango Bay, Japan. Model results show that in Tango Bay, where the Tsushima Warm Current passes offshore of the bay, under conditions of strong seasonal winds and river discharge, the water temperature and salinity are strongly influenced by surface heat flux and river discharge in the surface layer, respectively, while in the middle and bottom layers both are mainly controlled by open boundary conditions. The estuarine circulation is comparably influenced by all external forcing factors, the strong current, surface heat flux, wind stress, and river discharge. However, the influence degree of each forcing factor varies with temporal variations in external forcing factors as: the influence of open boundary conditions is higher in spring and early summer when the stronger current passes offshore of the bay, that of surface heat flux reflects the absolute value of surface heat flux, that of wind stress is higher in late fall and winter due to strong seasonal winds, and that of river discharge is higher in early spring due to snow-melting and summer and early fall due to flood events.

Theories for the winds from Wolf Rayet stars

International Nuclear Information System (INIS)

Cassinelli, J.P.

1982-01-01

The massive and fast winds of Wolf Rayet stars present a serious momentum problem for the line-driven wind theories that are commonly used to explain the fast winds of early type stars. It is perhaps possible for the winds to be driven by lines, if multiple scattering occurs and if there are a sufficient number of lines in the spectrum so that large fraction of the continuum is blocked by line opacity in the winds. Several other mechanisms are discussed, in particular two that rely on strong magnetic fields: a) Alfven wave driven wind models like those recently developed by Hartmann and MacGregor for late type supergiants and b) the ''Fast Magnetic Rotator'' model that was developed by Belcher and MacGregor for the winds from pre-main sequence stars. In either model, large magnetic fields (approximately equal to 10 4 gauss) are required to drive the massive and fast winds of Wolf Rayet stars. Smaller fields might be possible if the multiple scattering line radiation force can be relied on to provide a final acceleration to terminal velocity. (Auth.)

Representativeness of wind measurements in moderately complex terrain

Science.gov (United States)

van den Bossche, Michael; De Wekker, Stephan F. J.

2018-02-01

We investigated the representativeness of 10-m wind measurements in a 4 km × 2 km area of modest relief by comparing observations at a central site with those at four satellite sites located in the same area. Using a combination of established and new methods to quantify and visualize representativeness, we found significant differences in wind speed and direction between the four satellite sites and the central site. The representativeness of the central site wind measurements depended strongly on surface wind speed and direction, and atmospheric stability. Through closer inspection of the observations at one of the satellite sites, we concluded that terrain-forced flows combined with thermally driven downslope winds caused large biases in wind direction and speed. We used these biases to generate a basic model, showing that terrain-related differences in wind observations can to a large extent be predicted. Such a model is a cost-effective way to enhance an area's wind field determination and to improve the outcome of pollutant dispersion and weather forecasting models.

Modeling and Comparison of Power Converters for Doubly Fed Induction Generators in Wind Turbines

DEFF Research Database (Denmark)

Helle, Lars

on the generated power quality and controllability. A consequence of this increased focus has been an ever increased set of requirements formulated in national grid requirement. These requirements has forced wind turbines to evolve from a simple generator on a stick into complicated miniature power plants......During the last decades, renewable energy resources have become an ever increasing part of the world wide power generation and especially energy produced by wind turbines has captured a significant part of this power production. This large penetration of wind power has caused increased focus...... on the design engineers employed in the wind industry. Such a progress may force design engineers to adopt common practice from more or less related technologies rather than finding the optimum solution for the specific application. For instance when applying power electronic converters to wind turbines...

Measurement of Unsteady Aerodynamics Load on the Blade of Field Horizontal Axis Wind Turbine

Science.gov (United States)

Kamada, Yasunari; Maeda, Takao; Naito, Keita; Ouchi, Yuu; Kozawa, Masayoshi

This paper describes an experimental field study of the rotor aerodynamics of wind turbines. The test wind turbine is a horizontal axis wind turbine, or: HAWT with a diameter of 10m. The pressure distributions on the rotating blade are measured with multi point pressure transducers. Sectional aerodynamic forces are analyzed from pressure distribution. Blade root moments are measured simultaneously by a pair of strain gauges. The inflow wind is measured by a three component sonic anemometer, the local inflow of the blade section are measured by a pair of 7 hole Pitot tubes. The relation between the aerodynamic moments on the blade root from pressure distribution and the mechanical moment from strain gauges is discussed. The aerodynamic moments are estimated from the sectional aerodynamic forces and show oscillation caused by local wind speed and direction change. The mechanical moment shows similar oscillation to the aerodynamic excepting the short period oscillation of the blade first mode frequency. The fluctuation of the sectional aerodynamic force triggers resonant blade oscillations. Where stall is present along the blade section, the blade's first mode frequency is dominant. Without stall, the rotating frequency is dominant in the blade root moment.

Wind-power plant

Energy Technology Data Exchange (ETDEWEB)

Kling, A

1976-08-26

The invention is concerned with a wind-power plant whose rotor axis is pivoted in the supporting structure and swingable around an axis of tilt, forming an angle with the rotor axis and the vertical axis, and allowing precession of the rotor. On changes of wind direction an electric positioning device is moving the rotor axis into the new direction in such a way that no precession forces are exerted on the supporting structure and this one may very easily be held. Instead of one rotor, also a type with two coaxial, co-planar countercurrent rotors may be used. Each of the two countercurrent rotors is carrying a number of magnetic poles, distributed all over the circumference, acting together with the magnetic poles of the other rotor. At least the poles of one rotor have electric line windings being connected by leads with a collector so that the two rotors form the two parts of a power generator being each rotatable with respect to the other ('stator' and 'rotor').

East Antarctic rifting triggers uplift of the Gamburtsev Mountains

Science.gov (United States)

Ferraccioli, F.; Finn, Carol A.; Jordan, Tom A.; Bell, Robin E.; Anderson, Lester M.; Damaske, Detlef

2011-01-01

The Gamburtsev Subglacial Mountains are the least understood tectonic feature on Earth, because they are completely hidden beneath the East Antarctic Ice Sheet. Their high elevation and youthful Alpine topography, combined with their location on the East Antarctic craton, creates a paradox that has puzzled researchers since the mountains were discovered in 1958. The preservation of Alpine topography in the Gamburtsevs may reflect extremely low long-term erosion rates beneath the ice sheet, but the mountains’ origin remains problematic. Here we present the first comprehensive view of the crustal architecture and uplift mechanisms for the Gamburtsevs, derived from radar, gravity and magnetic data. The geophysical data define a 2,500-km-long rift system in East Antarctica surrounding the Gamburtsevs, and a thick crustal root beneath the range. We propose that the root formed during the Proterozoic assembly of interior East Antarctica (possibly about 1 Gyr ago), was preserved as in some old orogens and was rejuvenated during much later Permian (roughly 250 Myr ago) and Cretaceous (roughly 100 Myr ago) rifting. Much like East Africa, the interior of East Antarctica is a mosaic of Precambrian provinces affected by rifting processes. Our models show that the combination of rift-flank uplift, root buoyancy and the isostatic response to fluvial and glacial erosion explains the high elevation and relief of the Gamburtsevs. The evolution of the Gamburtsevs demonstrates that rifting and preserved orogenic roots can produce broad regions of high topography in continental interiors without significantly modifying the underlying Precambrian lithosphere.

Single-sided natural ventilation driven by wind pressure and temperature difference

DEFF Research Database (Denmark)

Larsen, Tine Steen; Heiselberg, Per

2008-01-01

-scale wind tunnel experiments have been made with the aim of making a new expression for calculation of the airflow rate in single-sided natural ventilation. During the wind tunnel experiments it was found that the dominating driving force differs between wind speed and temperature difference depending......Even though opening a window for ventilation of a room seems very simple, the flow that occurs in this situation is rather complicated. The amount of air going through the window opening will depend on the wind speed near the building, the temperatures inside and outside the room, the wind...

Wind tunnel test on PC cable-stayed bridge; PC shachokyo no taifu seino shiken

Energy Technology Data Exchange (ETDEWEB)

Kubo, Y. [Kyushu Inst. of Technology, Kitakyushu (Japan). Faculty of Engineering

1997-05-30

This paper describes the wind tunnel test on a PC cable-stayed bridge. The aerodynamic force that acts on a building is represented by the drag that works in the wind direction, the lift that works perpendicularly to the wind direction, and the aerodynamic moment that causes rotation. In the measurement of wind load, a girder is partially extracted in the wind tunnel and set in a three-component balance, and the drag, lift, and aerodynamic moment are measured using a strain meter while blowing the wind. In a wind tunnel experiment, the similarity on Reynolds number, field number, rigidity, hydraulic force, structural attenuation, and reduced wind velocity is required. However, the wind velocity in the actual bridge uses the same air as that in an experiment. The similarity rule on the Reynolds is not thus satisfied. It is necessary to cause no self-excited vibration (galloping and flutter) as wind-resistant performance and suppress the eddy excitation to less than the allowable amplitude. Moreover, the three-dimensional experiment using an elastic model is conducted in addition to the two-dimensional experiment using a rigid model. In the three-dimensional experiment, various vibration modes that occur in the actual bridge appear. 12 refs., 15 figs.

Vortex lattice modelling of winglets on wind turbine blades. 3. ed.

Energy Technology Data Exchange (ETDEWEB)

Doessing, M.

2007-08-15

The power production of wind turbines can be increased by the use of winglets without increasing the swept area. This makes them suitable for sites with restrictions in rotor diameter and in wind farms. The present project aims at understanding how winglets influences the flow and the aerodynamic forces on wind turbine blades. A free wake vortex lattice code and a fast design algorithm for a horizontal axis wind turbine under steady conditions has been developed. 2 winglet designs are treated in detail. (au)

A methodology for the design and testing of atmospheric boundary layer models for wind energy applications

Directory of Open Access Journals (Sweden)

J. Sanz Rodrigo

2017-02-01

Full Text Available The GEWEX Atmospheric Boundary Layer Studies (GABLS 1, 2 and 3 are used to develop a methodology for the design and testing of Reynolds-averaged Navier–Stokes (RANS atmospheric boundary layer (ABL models for wind energy applications. The first two GABLS cases are based on idealized boundary conditions and are suitable for verification purposes by comparing with results from higher-fidelity models based on large-eddy simulation. Results from three single-column RANS models, of 1st, 1.5th and 2nd turbulence closure order, show high consistency in predicting the mean flow. The third GABLS case is suitable for the study of these ABL models under realistic forcing such that validation versus observations from the Cabauw meteorological tower are possible. The case consists on a diurnal cycle that leads to a nocturnal low-level jet and addresses fundamental questions related to the definition of the large-scale forcing, the interaction of the ABL with the surface and the evaluation of model results with observations. The simulations are evaluated in terms of surface-layer fluxes and wind energy quantities of interest: rotor equivalent wind speed, hub-height wind direction, wind speed shear and wind direction veer. The characterization of mesoscale forcing is based on spatially and temporally averaged momentum budget terms from Weather Research and Forecasting (WRF simulations. These mesoscale tendencies are used to drive single-column models, which were verified previously in the first two GABLS cases, to first demonstrate that they can produce similar wind profile characteristics to the WRF simulations even though the physics are more simplified. The added value of incorporating different forcing mechanisms into microscale models is quantified by systematically removing forcing terms in the momentum and heat equations. This mesoscale-to-microscale modeling approach is affected, to a large extent, by the input uncertainties of the mesoscale

Does slab-window opening cause uplift of the overriding plate? A case study from the Gulf of California

Science.gov (United States)

Mark, Chris; Chew, David; Gupta, Sanjeev

2017-11-01

Complete subduction of an oceanic plate results in slab-window opening. A key uncertainty in this process is whether the higher heat flux and asthenospheric upwelling conventionally associated with slab-window opening generate a detectable topographic signature in the overriding plate. We focus on the Baja California Peninsula, which incorporates the western margin of the Gulf of California rift. The topography and tectonics of the rift flank along the peninsula are strongly bimodal. North of the Puertecitos accommodation zone, the primary drainage divide attains a mean elevation of ca. 1600 m above sea level (asl), above an asthenospheric slab-window opened by Pacific-Farallon spreading ridge subduction along this section of the trench at ca. 17-15 Ma. To the south, mean topography decreases abruptly to ca. 800 m asl (excluding the structurally distinct Los Cabos block at the southern tip of the peninsula), above fragments of the oceanic Farallon slab which stalled following slab tear-off at ca. 15-14 Ma. Along the peninsula, a low-relief surface established atop Miocene subduction-related volcaniclastic units has been incised by a west-draining canyon network in response to uplift. These canyons exhibit cut-and-fill relationships with widespread post-subduction lavas. Here, we utilise LANDSAT and digital elevation model (DEM) data, integrated with previously published K-Ar and 40Ar/39Ar lava crystallisation ages, to constrain the onset of rift flank uplift to ca. 9-5 Ma later than slab-window formation in the north and ca. 11-10 Ma later in the south. These greatly exceed response time estimates of ca. 2 Ma or less for uplift triggered by slab-window opening. Instead, uplift timing of the high-elevation northern region is consistent with lower-lithospheric erosion driven by rift-related convective upwelling. To the south, stalled slab fragments likely inhibited convective return flow, preventing lithospheric erosion and limiting uplift to the isostatic response

Diode Laser Assisted Filament Winding of Thermoplastic Matrix Composites

Science.gov (United States)

Quadrini, Fabrizio; Squeo, Erica Anna; Prosperi, Claudia

2010-01-01

A new consolidation method for the laser-assisted filament winding of thermoplastic prepregs is discussed: for the first time a diode laser is used, as well as long glass fiber reinforced polypropylene prepregs. A consolidation apparatus was built by means of a CNC motion table, a stepper motor and a simple tensioner. Preliminary tests were performed in a hoop winding configuration: only the winding speed was changed, and all the other process parameters (laser power, distance from the laser focus, consolidation force) were kept constant. Small wound rings with an internal diameter of 25 mm were produced and compression tests were carried out to evaluate the composite agglomeration in dependence of the winding speed. At lower winding speeds, a strong interpenetration of adjacent layers was observed.

Late Quaternary uplift along the North America-Caribbean plate boundary: Evidence from the sea level record of Guantanamo Bay, Cuba

Science.gov (United States)

Muhs, Daniel R.; Schweig, Eugene S.; Simmons, Kathleen R.; Halley, Robert B.

2017-12-01

The tectonic setting of the North America-Caribbean plate boundary has been studied intensively, but some aspects are still poorly understood, particularly along the Oriente fault zone. Guantanamo Bay, southern Cuba, is considered to be on a coastline that is under a transpressive tectonic regime along this zone, and is hypothesized to have a low uplift rate. We tested this by studying emergent reef terrace deposits around the bay. Reef elevations in the protected, inner part of the bay are ∼11-12 m and outer-coast, wave-cut benches are as high as ∼14 m. Uranium-series analyses of corals yield ages ranging from ∼133 ka to ∼119 ka, correlating this reef to the peak of the last interglacial period, marine isotope stage (MIS) 5.5. Assuming a span of possible paleo-sea levels at the time of the last interglacial period yields long-term tectonic uplift rates of 0.02-0.11 m/ka, supporting the hypothesis that the tectonic uplift rate is low. Nevertheless, on the eastern and southern coasts of Cuba, east and west of Guantanamo Bay, there are flights of multiple marine terraces, at higher elevations, that could record a higher rate of uplift, implying that Guantanamo Bay may be anomalous. Southern Cuba is considered to have experienced a measurable but modest effect from glacial isostatic adjustment (GIA) processes. Thus, with a low uplift rate, Guantanamo Bay should show no evidence of emergent marine terraces dating to the ∼100 ka (MIS 5.3) or ∼80 ka (MIS 5.1) sea stands and results of the present study support this.

Assessment of research needs for wind turbine rotor materials technology

Energy Technology Data Exchange (ETDEWEB)

1991-01-01

Wind-driven power systems is a renewable energy technology that is still in the early stages of development. Wind power plants installed in early 1980s suffered structural failures chiefly because of incomplete understanding of wind forces (turbulent), in some cases because of poor product quality. Failures of rotor blades are now somewhat better understood. This committee has examined the experience base accumulated by wind turbines and the R and D programs sponsored by DOE. It is concluded that a wind energy system such as is described is within the capability of engineering practice; however because of certain gaps in knowledge, and the presence of only one major integrated manufacturer of wind power machines in the USA, a DOE R and D investment is still required.

INFLUENCE OF THE AMBIENT SOLAR WIND FLOW ON THE PROPAGATION BEHAVIOR OF INTERPLANETARY CORONAL MASS EJECTIONS

Energy Technology Data Exchange (ETDEWEB)

Temmer, Manuela; Rollett, Tanja; Moestl, Christian; Veronig, Astrid M. [Kanzelhoehe Observatory-IGAM, Institute of Physics, University of Graz, Universitaetsplatz 5, A-8010 Graz (Austria); Vrsnak, Bojan [Hvar Observatory, Faculty of Geodesy, University of Zagreb, Kaciceva 26, HR-10000 Zagreb (Croatia); Odstrcil, Dusan [Cooperative Institute for Research in Environmental Sciences, University of Colorado at Boulder, Boulder, CO (United States)

2011-12-20

We study three coronal mass ejection (CME)/interplanetary coronal mass ejection (ICME) events (2008 June 1-6, 2009 February 13-18, and 2010 April 3-5) tracked from Sun to 1 AU in remote-sensing observations of Solar Terrestrial Relations Observatory Heliospheric Imagers and in situ plasma and magnetic field measurements. We focus on the ICME propagation in interplanetary (IP) space that is governed by two forces: the propelling Lorentz force and the drag force. We address the question: which heliospheric distance range does the drag become dominant and the CME adjust to the solar wind flow. To this end, we analyze speed differences between ICMEs and the ambient solar wind flow as a function of distance. The evolution of the ambient solar wind flow is derived from ENLIL three-dimensional MHD model runs using different solar wind models, namely, Wang-Sheeley-Arge and MHD-Around-A-Sphere. Comparing the measured CME kinematics with the solar wind models, we find that the CME speed becomes adjusted to the solar wind speed at very different heliospheric distances in the three events under study: from below 30 R{sub Sun }, to beyond 1 AU, depending on the CME and ambient solar wind characteristics. ENLIL can be used to derive important information about the overall structure of the background solar wind, providing more reliable results during times of low solar activity than during times of high solar activity. The results from this study enable us to obtain greater insight into the forces acting on CMEs over the IP space distance range, which is an important prerequisite for predicting their 1 AU transit times.

INFLUENCE OF THE AMBIENT SOLAR WIND FLOW ON THE PROPAGATION BEHAVIOR OF INTERPLANETARY CORONAL MASS EJECTIONS

International Nuclear Information System (INIS)

Temmer, Manuela; Rollett, Tanja; Möstl, Christian; Veronig, Astrid M.; Vršnak, Bojan; Odstrčil, Dusan

2011-01-01

We study three coronal mass ejection (CME)/interplanetary coronal mass ejection (ICME) events (2008 June 1-6, 2009 February 13-18, and 2010 April 3-5) tracked from Sun to 1 AU in remote-sensing observations of Solar Terrestrial Relations Observatory Heliospheric Imagers and in situ plasma and magnetic field measurements. We focus on the ICME propagation in interplanetary (IP) space that is governed by two forces: the propelling Lorentz force and the drag force. We address the question: which heliospheric distance range does the drag become dominant and the CME adjust to the solar wind flow. To this end, we analyze speed differences between ICMEs and the ambient solar wind flow as a function of distance. The evolution of the ambient solar wind flow is derived from ENLIL three-dimensional MHD model runs using different solar wind models, namely, Wang-Sheeley-Arge and MHD-Around-A-Sphere. Comparing the measured CME kinematics with the solar wind models, we find that the CME speed becomes adjusted to the solar wind speed at very different heliospheric distances in the three events under study: from below 30 R ☉ , to beyond 1 AU, depending on the CME and ambient solar wind characteristics. ENLIL can be used to derive important information about the overall structure of the background solar wind, providing more reliable results during times of low solar activity than during times of high solar activity. The results from this study enable us to obtain greater insight into the forces acting on CMEs over the IP space distance range, which is an important prerequisite for predicting their 1 AU transit times.

On the Effect of Offshore Wind Parks on Ocean Dynamics

Science.gov (United States)

Ludewig, E.; Pohlmann, T.

2012-12-01

Nowadays renewable energy resources play a key role in the energy supply discussion and especially an increasingly interest in wind energy induces intensified installations of wind parks. At this offshore wind energy gains in popularity in the course of higher and more consistent energy availability than over land. For example Germany's government adopted a national interurban offshore wind energy program comprising the construction of hundreds of wind turbines within Germany's Exclusive Economic Zone to ensure up to 50% of Germany's renewable energy supply. The large number of installation in coastal regions asks for analyzing the impact of offshore wind parks (OWPs) on the atmosphere and the ocean. As known from literature such wind parks excite also-called wake-effect and such an influence on the wind field in turn affects ocean circulation. To cover OWP's impact on ocean dynamics we evaluate model simulations using the Hamburg Shelf-Ocean-Model (HAMSOM). All simulations were driven with a wind forcing produced by the Mesoscale Atmosphere Model of the Hamburg University (METRAS) which has implemented wind turbines. Wind forcing data were generated in collaboration with and by courtesy of the Meteorological Institute of the University of Hamburg, Department Technical Meteorology, Numeric Modeling-METRAS. To evaluate dynamical changes forced by the OWP's wind wake-effect we did a sensitivity study with a theoretical setup of a virtual ocean of 60m depth with a flat bottom and a temperature and salinity stratification according to common North Sea's conditions. Here our results show that already a small OWP of 12 wind turbines, placed in an area of 4 km^2, lead to a complex change in ocean dynamics. Due to the wake-effect zones of upwelling and downwelling are formed within a minute after turning-on wind turbines. The evolving vertical cells have a size of around 15x15 kilometers with a vertical velocity in order of 10^-2 mm/sec influencing the dynamic of an area

Long-Term Uplift in the Altiplano-Puna Neovolcanic Zone: Evidence of an Active Magmatic Diapir?

Science.gov (United States)

Fialko, Y.; Pearse, J.

2012-12-01

We present InSAR observations of a long-term uplift in the Altiplano-Puna neovolcanic zone (central Andes, South America). Previous observations revealed a a massive Ultra Low Velocity Zone (ULVZ) at depth of 17-19 km (Zandt et al., 2003), and surface deformation that was attributed to Uturuncu, a dormant volcano in the middle of the Altiplano-Puna neovolcanic zone (Pritchard and Simons, 2002). Our time series analysis of combined data from different sensors (ERS-1/2 and ENVISAT), satellite tracks, and observation modes (fine beam and ScanSAR) reveals that the central uplift has persisted at a nearly constant rate of ~1 cm/yr over the last two decades, and is surrounded by a broad zone of subsidence. We use the satellite line-of-sight velocities from different look directions to constrain the depth and geometry of the inferred sources of magmatic unrest. Inversions based on elastic half-space models indicate that the inflation source is located well below the brittle-ductile transition, and likely resides at the depth of the seismically imaged ULVZ. We investigated the effects of inelastic deformation in the ambient crust using finite element models. The models incorporated laboratory-derived rheologies of the ambient crust, and geotherms appropriate for an active neo-volcanic zone such as the one in the Altiplano-Puna province. Based on a large number of numerical simulations constrained by the observed surface velocities, we conclude that the ongoing uplift and peripheral subsidence result from a large mid-crustal diapir fed by a partially molten source region in the middle crust. The observed pattern of surface deformation due to the Altiplano-Puna ULVZ is remarkably similar to that due to the Socorro Magma Body (SMB) in central New Mexico, USA (Pearse and Fialko, 2010), suggesting a common process. mosaic of the mean LOS velocity showing uplift and peripheral subsidence due to the inferred mid-crustal diapir.

Moduli stabilization and uplifting with dynamically generated F-terms

International Nuclear Information System (INIS)

Dudas, Emilian; Papineau, Chloe; Pokorski, Stefan

2007-01-01

We use the F-term dynamical supersymmetry breaking models with metastable vacua in order to uplift the vacuum energy in the KKLT moduli stabilization scenario. The main advantage compared to earlier proposals is the manifest supersymmetric treatment and the natural coexistence of a TeV gravitino mass with a zero cosmological constant. We argue that it is generically difficult to avoid anti de-Sitter supersymmetric minima, however the tunneling rate from the metastable vacuum with zero vacuum energy towards them can be very suppressed. We briefly comment on the properties of the induced soft terms in the observable sector

Moduli stabilization and uplifting with dynamically generated F-terms

Energy Technology Data Exchange (ETDEWEB)

Dudas, Emilian [CERN Theory Division, CH-1211, Geneva 23 (Switzerland); Papineau, Chloe [CPhT, Ecole Polytechnique, F-91128 Palaiseau Cedex (France); Pokorski, Stefan [Institute of Theoretical Physics, Univ. of Warsaw, 00-681 Warsaw (Poland)

2007-02-15

We use the F-term dynamical supersymmetry breaking models with metastable vacua in order to uplift the vacuum energy in the KKLT moduli stabilization scenario. The main advantage compared to earlier proposals is the manifest supersymmetric treatment and the natural coexistence of a TeV gravitino mass with a zero cosmological constant. We argue that it is generically difficult to avoid anti de-Sitter supersymmetric minima, however the tunneling rate from the metastable vacuum with zero vacuum energy towards them can be very suppressed. We briefly comment on the properties of the induced soft terms in the observable sector.

Numerical simulation on a straight-bladed vertical axis wind turbine with auxiliary blade

Science.gov (United States)

Li, Y.; Zheng, Y. F.; Feng, F.; He, Q. B.; Wang, N. X.

2016-08-01

To improve the starting performance of the straight-bladed vertical axis wind turbine (SB-VAWT) at low wind speed, and the output characteristics at high wind speed, a flexible, scalable auxiliary vane mechanism was designed and installed into the rotor of SB-VAWT in this study. This new vertical axis wind turbine is a kind of lift-to-drag combination wind turbine. The flexible blade expanded, and the driving force of the wind turbines comes mainly from drag at low rotational speed. On the other hand, the flexible blade is retracted at higher speed, and the driving force is primarily from a lift. To research the effects of the flexible, scalable auxiliary module on the performance of SB-VAWT and to find its best parameters, the computational fluid dynamics (CFD) numerical calculation was carried out. The calculation result shows that the flexible, scalable blades can automatic expand and retract with the rotational speed. The moment coefficient at low tip speed ratio increased substantially. Meanwhile, the moment coefficient has also been improved at high tip speed ratios in certain ranges.

Everyday hassles and uplifts among women on long-term sick-leave due to stress-related disorders.

Science.gov (United States)

Johansson, Gun; Eklund, Mona; Erlandsson, Lena-Karin

2012-05-01

A balance between different experiences of occupations in everyday life is important for well-being. The study aim was to describe hassles and uplifts in everyday occupations among women on long-term sick-leave due to stress-related disorders. The sample consisted of 77 women and experiences were collected by the THU-5 instrument. The statements were analysed using quantitative content analysis. Data were categorized into three domains of hassles concerning oneself, doings, and social and physical context. The same domains occurred among the uplifts. Hassles were mostly generated by disturbing people around the women and by their limited body functions. The women were uplifted by supportive social relationships and by performing relaxing and calming occupations. The study illuminates the strong need for social support among women on sick-leave, as well as their low level of energy, which was an obvious obstacle for performing occupations. It is suggested that, in order to increase well-being in the target group, the occupational therapist should meet their need for occupations that match their current level of energy. The challenge for the client is to avoid remaining in a pattern of low-demand occupations without exceeding her/his capacity and returning to an unhealthy pattern of occupations.

Cenozoic Uplift and Climate Change of the Northeast Tibetan Plateau: Evidence from Leaf Wax Stable Isotopic Records

Science.gov (United States)

Hou, M.; Zhuang, G.; Wu, M.

2017-12-01

Topics about the deformation history and uplift mechanism of Tibetan Plateau have been largely debated in the past few decades. Different geodynamic models present different predictions on the mountain building processes and hence the surface uplift history. For example, one tectonic model suggests a rapid uplift (>1.0 to 2.0 km) of the Tibetan Plateau in the period of ca. 10 to 8 Ma as result of isostatic rebound due to the removal of over-thickened mental lithosphere beneath. Whilst the stepwise uplift model infers that the high topography was growing progressively from south to north with the Northeast Tibetan Plateau being built in the Pliocene to present. In this case, the timing of Cenozoic uplift of Northeast Tibetan Plateau would provide information for distinguishing competing geodynamic processes. The stable isotope based paleoaltimetry holds the key to answering when the high topography was built. Additionally, the evolution of Cenozoic Asian climate was argued to be closely related to the high topography built up on the Tibetan Plateau since the India-Asian collision and/or impacted by the global change. To understand when the high topography was built and how the growth of Tibetan Plateau impacted the climate, we reconstructed the long-term histories of paleohydrology from hinterland and foreland basins in the Northeast Tibetan Plateau. We applied the compound-specific isotope hydrogen analysis to leaf wax n-alkanes (δ2Hn-alk) that are preserved in well-dated stratigraphic series (ca. 24 Ma to the present) in the Northeast Tibetan Plateau. The newly reconstructed δ2Hn-alk supports the inference of high topography on the Northeast Tibetan Plateau was built during the middle to late Miocene. Our inference is consistent with sedimentary and basement rock studies that show fundamental changes in facies and provenance and exhumation history. The new δ2Hn-alk record also reveals that the regional climate became drier since the middle Miocene following the

Wind-waves interactions in the Gulf of Eilat

Science.gov (United States)

Shani-Zerbib, Almog; Liberzon, Dan; T-SAIL Team

2017-11-01

The Gulf of Eilat, at the southern tip of Israel, with its elongated rectangular shape and unique diurnal wind pattern is an appealing location for wind-waves interactions research. Results of experimental work will be reported analyzing a continuous, 50 hour long, data. Using a combined array of wind and waves sensing instruments, the wave field statistics and its response to variations of wind forcing were investigated. Correlations between diurnal fluctuations in wind magnitude and direction and the wave field response will be discussed. The directional spread of waves' energy, as estimated by the Wavelet Directional Method, showed a strong response to small variations in wind flow direction attributed to the unique topography of the gulf surroundings and its bathymetry. Influenced by relatively strong winds during the light hours, the wave field was dominated by a significant amount of breakings that are well pronounced in the saturation range of waves spectra. Temporal growth and decay behavior of the waves during the morning and evening wind transition periods was examined. Sea state induced roughness, as experienced by the wind flow turbulent boundary layer, is examined in view of the critical layer theory. Israel Science Foundation Grant # 1521/15.

Actuator forces in CFD: RANS and LES modeling in OpenFOAM

International Nuclear Information System (INIS)

Schito, P; Zasso, A

2014-01-01

Wind turbine wakes are a very challenging topic for scientific computations, but modern CFD frameworks and latest HPC centers allow setting up numerical computations on the wake induced by the wind turbine. The main issues is that the correct modeling of the wake is related to the correct modeling of the interaction between the blade and the incoming flow. The aim of the proposed work is to estimate the aerodynamic forces acting on the blades in order to correctly generate the rotor wake applying equivalent aerodynamic force source on the flow. The definition of a blade forces is done developing a model able to correctly estimate this aerodynamic forces as a function of the local flow seen by the blade during its revolution

Tiotropium as a first maintenance drug in COPD: secondary analysis of the UPLIFT trial

DEFF Research Database (Denmark)

Troosters, T; Celli, B; Lystig, T

2010-01-01

-term Impacts on Function with Tiotropium (UPLIFT) was conducted. Analysis focused on the effect of tiotropium versus matching placebo in the 810 (13.5%) COPD patients not on other maintenance treatment (long-acting beta-agonists, inhaled corticosteroids, theophyllines or anticholinergics) at randomisation...

Aerodynamic flow simulation of wind turbine: Downwind versus upwind configuration

International Nuclear Information System (INIS)

Janajreh, Isam; Qudaih, Rana; Talab, Ilham; Ghenai, Chaouki

2010-01-01

Large scale wind turbines and wind farms continue to grow mounting 94.1 GW of the electrical grid capacity in 2007 and expected to reach 160.0 GW in 2010. Wind energy plays a vital role in the quest for renewable and sustainable energy as well as in reducing carbon emission. Early generation wind turbines (windmills) were used mainly for water pumping and seed grinding, whereas today they generate 1/5 of the current Denmark's electricity and will double its grid capacity reaching 12.5% in 2010. Wind energy is plentiful (72 TW estimated to be commercially viable) and clean while its intensive capital cost still impede widespread deployment. However, there are technological challenges, i.e. high fatigue load, noise emission, and meeting stringent reliability and safety standards. Newer inventions, e.g., downstream wind turbines and flapping rotor blades, are sought to enhance their performance, i.e. lower turning moments and cut-in speed and to absorb portion of the cost due to the absent of yaw mechanisms. In this work, numerical analysis of the downstream wind turbine blade is conducted. In particular, the interaction between the tower and the rotor passage is investigated. Circular cross sectional tower and aerofoil shapes are considered in a staggered configuration and under cross-stream motion. The resulting blade static pressure and aerodynamic forces are computed at different incident wind angles and wind speeds. The computed forces are compared to the conventional upstream wind turbine. Steady state and transient, incompressible, viscous Navier-Stokes and turbulent flow analysis are employed. The k-epsilon model is utilized as the turbulence closure. The passage of the rotor blade is governed by ALE and is represented numerically as a sliding mesh against the upstream fixed tower domain.

Rotary Balance Wind Tunnel Testing for the FASER Flight Research Aircraft

Science.gov (United States)

Denham, Casey; Owens, D. Bruce

2016-01-01

Flight dynamics research was conducted to collect and analyze rotary balance wind tunnel test data in order to improve the aerodynamic simulation and modeling of a low-cost small unmanned aircraft called FASER (Free-flying Aircraft for Sub-scale Experimental Research). The impetus for using FASER was to provide risk and cost reduction for flight testing of more expensive aircraft and assist in the improvement of wind tunnel and flight test techniques, and control laws. The FASER research aircraft has the benefit of allowing wind tunnel and flight tests to be conducted on the same model, improving correlation between wind tunnel, flight, and simulation data. Prior wind tunnel tests include a static force and moment test, including power effects, and a roll and yaw damping forced oscillation test. Rotary balance testing allows for the calculation of aircraft rotary derivatives and the prediction of steady-state spins. The rotary balance wind tunnel test was conducted in the NASA Langley Research Center (LaRC) 20-Foot Vertical Spin Tunnel (VST). Rotary balance testing includes runs for a set of given angular rotation rates at a range of angles of attack and sideslip angles in order to fully characterize the aircraft rotary dynamics. Tests were performed at angles of attack from 0 to 50 degrees, sideslip angles of -5 to 10 degrees, and non-dimensional spin rates from -0.5 to 0.5. The effects of pro-spin elevator and rudder deflection and pro- and anti-spin elevator, rudder, and aileron deflection were examined. The data are presented to illustrate the functional dependence of the forces and moments on angle of attack, sideslip angle, and angular rate for the rotary contributions to the forces and moments. Further investigation is necessary to fully characterize the control effectors. The data were also used with a steady state spin prediction tool that did not predict an equilibrium spin mode.

Dynamic Analysis of Wind Turbines Including Soil-Structure Interaction

DEFF Research Database (Denmark)

Harte, M.; Basu, B.; Nielsen, Søren R.K.

2012-01-01

This paper investigates the along-wind forced vibration response of an onshore wind turbine. The study includes the dynamic interaction effects between the foundation and the underlying soil, as softer soils can influence the dynamic response of wind turbines. A Multi-Degree-of-Freedom (MDOF......) horizontal axes onshore wind turbine model is developed for dynamic analysis using an Euler–Lagrangian approach. The model is comprised of a rotor blade system, a nacelle and a flexible tower connected to a foundation system using a substructuring approach. The rotor blade system consists of three rotating...... for displacement of the turbine system are obtained and the modal frequencies of the combined turbine-foundation system are estimated. Simulations are presented for the MDOF turbine structure subjected to wind loading for different soil stiffness conditions. Steady state and turbulent wind loading, developed using...

Neogene-Quaternary slow coastal uplift of Western Europe through the perspective of sequences of strandlines from the Cotentin Peninsula (Normandy, France)

Science.gov (United States)

Pedoja, K.; Jara-Muñoz, J.; De Gelder, G.; Robertson, J.; Meschis, M.; Fernandez-Blanco, D.; Nexer, M.; Poprawski, Y.; Dugué, O.; Delcaillau, B.; Bessin, P.; Benabdelouahed, M.; Authemayou, C.; Husson, L.; Regard, V.; Menier, D.; Pinel, B.

2018-02-01

The Cotentin Peninsula (Normandy, France) displays sequences of marine terraces and rasas, the latter being wide Late Cenozoic coastal erosion surfaces, that are typical of Western European coasts in Portugal, Spain, France and southern England. Remote sensing imagery and field mapping enabled reappraisal of the Cotentin coastal sequences. From bottom to top, the N Cotentin sequence includes four previously recognized Pleistocene marine terraces (T1 to T4) at elevations 5e), sequential morphostratigraphy and modelling, we have reappraised uplift rates and derived: (i) mean Upper Pleistocene (i.e. since MIS 5e 122 +/- 6 ka, i.e. kilo annum) apparent uplift rates of 0.04 ± 0.01 mm/yr, (ii) mean Middle Pleistocene eustasy-corrected uplift rates of 0.09 ± 0.03 mm/yr, and (iii) low mean Pleistocene uplift rates of 0.01 mm/yr. Extrapolations of these slow rates combined with geological evidence implies that the formation of the sequences from the Cotentin Peninsula occurred between 3 Ma (Pliocene) and 15 Ma (Miocene), which cannot be narrowed down further without additional research. Along the coasts of Western Europe, sequences of marine terraces and rasas are widespread (169 preserve the MIS 5e benchmark). In Spain, Portugal, S England and other parts of western France, the sequences morphostratigraphy is very similar to that of Cotentin. The onset of such Western European sequences occurred during the Miocene (e.g. Spain) or Pliocene (e.g. Portugal). We interpret this Neogene-Quaternary coastal uplift as a symptom of the increasing lithospheric compression that accompanies Cenozoic orogenies.

Waves in the Red Sea: Response to monsoonal and mountain gap winds

KAUST Repository

Ralston, David K.; Jiang, Houshuo; Farrar, J. Thomas

2013-01-01

An unstructured grid, phase-averaged wave model forced with winds from a high resolution atmospheric model is used to evaluate wind wave conditions in the Red Sea over an approximately 2-year period. The Red Sea lies in a narrow rift valley

Grid impact of variable-speed wind turbines

Energy Technology Data Exchange (ETDEWEB)

Larsson, Aa [Chalmers Univ. of Technology, Dept. of Electric Power Engineering, Goeteborg (Sweden); Soerensen, P [Risoe National Lab., Roskilde (Denmark); Santjer, F [German Wind Energy Inst., DEWI, Wilhelmshaven (Germany)

1999-03-01

In this paper the power quality of variable-speed wind turbines equipped with forced-commutated inverters is investigated. Measurements have been taken on the same type of variable-speed wind turbines in Germany and Sweden. The measurements have been analysed according to existing IEC standards. Special attention has been paid to the aggregation of several wind turbines on flicker emission and harmonics. The aggregation has been compared with the summation laws used in the draft IEC 61400-21 `Power Quality Requirements for Grid Connected wind turbines`. The methods for calculating and summing flicker proposed by IEC Standards are reliable. Harmonics and inter-harmonics are treated in IEC 61000-4-7 and IEC 61000-3-6. The methods for summing harmonics and inter-harmonics in IEC 61000-3-6 are applicable to wind turbines. In order to obtain a correct magnitude of the frequency components, the use of a well-defined window width, according to IEC 61000-4-7 Amendment 1 is of a great importance. (au)

Computational modelling of an operational wind turbine and validation with LIDAR

Science.gov (United States)

Creech, Angus; Fruh, Wolf-Gerrit; Clive, Peter

2010-05-01

We present a computationally efficient method to model the interaction of wind turbines with the surrounding flow, where the interaction provides information on the power generation of the turbine and the generated wake behind the turbine. The turbine representation is based on the principle of an actuator volume, whereby the energy extraction and balancing forces on the fluids are formulated as body forces which avoids the extremely high computational costs of boundary conditions and forces. Depending on the turbine information available, those forces can be derived either from published turbine performance specifications or from their rotor and blade design. This turbine representation is then coupled to a Computational Fluid Dynamics package, in this case the hr-adaptive Finite-Element code Fluidity from Imperial College, London. Here we present a simulation of an operational 950kW NEG Micon NM54 wind turbine installed in the west of Scotland. The calculated wind is compared with LIDAR measurements using a Galion LIDAR from SgurrEnergy. The computational domain extends over an area of 6km by 6km and a height of 750m, centred on the turbine. The lower boundary includes the orography of the terrain and surface roughness values representing the vegetation - some forested areas and some grassland. The boundary conditions on the sides are relaxed Dirichlet conditions, relaxed to an observed prevailing wind speed and direction. Within instrumental errors and model limitations, the overall flow field in general and the wake behind the turbine in particular, show a very high degree of agreement, demonstrating the validity and value of this approach. The computational costs of this approach are such that it is possible to extend this single-turbine example to a full wind farm, as the number of required mesh nodes is given by the domain and then increases only linearly with the number of turbines

A parabolic velocity-decomposition method for wind turbines

Science.gov (United States)

Mittal, Anshul; Briley, W. Roger; Sreenivas, Kidambi; Taylor, Lafayette K.

2017-02-01

An economical parabolized Navier-Stokes approximation for steady incompressible flow is combined with a compatible wind turbine model to simulate wind turbine flows, both upstream of the turbine and in downstream wake regions. The inviscid parabolizing approximation is based on a Helmholtz decomposition of the secondary velocity vector and physical order-of-magnitude estimates, rather than an axial pressure gradient approximation. The wind turbine is modeled by distributed source-term forces incorporating time-averaged aerodynamic forces generated by a blade-element momentum turbine model. A solution algorithm is given whose dependent variables are streamwise velocity, streamwise vorticity, and pressure, with secondary velocity determined by two-dimensional scalar and vector potentials. In addition to laminar and turbulent boundary-layer test cases, solutions for a streamwise vortex-convection test problem are assessed by mesh refinement and comparison with Navier-Stokes solutions using the same grid. Computed results for a single turbine and a three-turbine array are presented using the NREL offshore 5-MW baseline wind turbine. These are also compared with an unsteady Reynolds-averaged Navier-Stokes solution computed with full rotor resolution. On balance, the agreement in turbine wake predictions for these test cases is very encouraging given the substantial differences in physical modeling fidelity and computer resources required.

Wind energy barometer - EurObserv'ER - February 2016

International Nuclear Information System (INIS)

2016-02-01

The spectacular rise of China's wind power market that resulted in connecting at least 30.5 GW, catapulted the global installation level to 62.7 GW in 2015- a 22% more than in 2014. The US and German markets also performed very well, the former because its tax credit mechanism remained in force and the latter because many of its offshore wind farms in the North Sea were connected to the grid. Global wind turbine capacity has increased by 17% and now stands at 432.6 GW

Regimes of seasonal air-sea interaction and implications for performance of forced simulations

Energy Technology Data Exchange (ETDEWEB)

Wu, Renguang [Center for Ocean-Land-Atmosphere Studies, Calverton, MD (United States); Kirtman, Ben P. [Center for Ocean-Land-Atmosphere Studies, Calverton, MD (United States); George Mason University, School of Computational Sciences, Fairfax, VA (United States)

2007-09-15

Sea surface temperature (SST) anomalies can induce anomalous convection through surface evaporation and low-level moisture convergence. This SST forcing of the atmosphere is indicated in a positive local rainfall-SST correlation. Anomalous convection can feedback on SST through cloud-radiation and wind-evaporation effects and wind-induced oceanic mixing and upwelling. These atmospheric feedbacks are reflected in a negative local rainfall-SST tendency correlation. As such, the simultaneous rainfall-SST and rainfall-SST tendency correlations can indicate the nature of local air-sea interactions. Based on the magnitude of simultaneous rainfall-SST and rainfall-SST tendency correlations, the present study identifies three distinct regimes of local air-sea interactions. The relative importance of SST forcing and atmospheric forcing differs in these regimes. In the equatorial central-eastern Pacific and, to a smaller degree, in the western equatorial Indian Ocean, SST forcing dominates throughout the year and the surface heat flux acts mainly as a damping term. In the tropical Indo-western Pacific Ocean regions, SST forcing and atmospheric forcing dominate alternatively in different seasons. Atmospheric forcing dominates in the local warm/rainy season. SST forcing dominates with a positive wind-evaporation feedback during the transition to the cold/dry season. SST forcing also dominates during the transition to the warm/rainy season but with a negative cloud-radiation feedback. The performance of atmospheric general circulation model simulations forced by observed SST is closely linked to the regime of air-sea interaction. The forced simulations have good performance when SST forcing dominates. The performance is low or poor when atmospheric forcing dominates. (orig.)

Repair Works for Uplift and Seepage Control in Existing Concrete Dams

Science.gov (United States)

1989-08-01

weathered and therefore where the presence of soil mterials is likely to occur in joints and fractures. Fig.5 - Varosa dam. Main results of mechanical...situations are associated with: emptying of reservoir by hot summer; water effects due to hydrostatic pressure and uplift; winter, spring and autumn...design stage were supported by tests of three-dimensional plaster- diatomite models, carried out at LNEC (1971c). The models were built in a scale of 1

Software tool for horizontal-axis wind turbine simulation

Energy Technology Data Exchange (ETDEWEB)

Vitale, A.J. [Instituto Argentino de Oceanografia, Camino La Carrindanga Km. 7, 5 CC 804, B8000FWB Bahia Blanca (Argentina); Universidad Tecnologica Nacional Facultad Regional Bahia Blanca, GESE, 11 de Abril 461, B8000LMI Bahia Blanca (Argentina); Dpto. de Ing. Electrica y de Computadoras, Universidad Nacional del Sur, Av. Alem 1253, 8000 Bahia Blanca (Argentina); Rossi, A.P. [Universidad Tecnologica Nacional Facultad Regional Bahia Blanca, GESE, 11 de Abril 461, B8000LMI Bahia Blanca (Argentina); Dpto. de Ing. Electrica y de Computadoras, Universidad Nacional del Sur, Av. Alem 1253, 8000 Bahia Blanca (Argentina)

2008-07-15

The main problem of a wind turbine generator design project is the design of the right blades capable of satisfying the specific energy requirement of an electric system with optimum performance. Once the blade has been designed for optimum operation at a particular rotor angular speed, it is necessary to determine the overall performance of the rotor under the range of wind speed that it will encounter. A software tool that simulates low-power, horizontal-axis wind turbines was developed for this purpose. With this program, the user can calculate the rotor power output for any combination of wind and rotor speeds, with definite blade shape and airfoil characteristics. The software also provides information about distribution of forces along the blade span, for different operational conditions. (author)

Seafloor Uplift in Middle Valley, Juan de Fuca Ridge: New High-Resolution Pressure Data

Science.gov (United States)

Inderbitzen, K. E.; Becker, K.; Davis, E. E.

2011-12-01

Currently, in-situ seafloor and basement pressures are continuously monitored and recorded by an ODP subseafloor hydrogeological observatory (CORK) located in Middle Valley, Juan de Fuca Ridge. Hole 857D was drilled in 1991 in thickly sedimented crust to a depth of 936 mbsf and instrumented with an original CORK that was replaced in 1996. A large hydrothermal field (Dead Dog) lies roughly 1.7 km north of the hole, and two isolated chimneys and several diffuse flow sites are located ~800 meters northeast. The borehole and the vent fields have been visited periodically by submersible/ROV since 1999. Recent results from the CORK at 857D have shown apparent seafloor uplift, supported by depth records from the submersible Alvin. A constant rate of pressure change of ~6 kPa/yr, from its initiation in 2005 to the visit in 2010, has reduced mean seafloor pressure by ~28 kPa, equivalent to nearly 3 meters of head. This uplift rate is several times the typical pre-eruption inflation rates observed at Axial Seamount further south along the Juan de Fuca Ridge. Initially, the apparent uplift at 857D did not seem to have any effect on local high-temperature hydrothermal venting, however recent operations in Middle Valley revealed distinct changes at not only the hydrothermal field to the northeast, but also a shutdown of high-temperature venting to the north of 857D. We will present new data from Middle Valley, including the first year of data collected by a high-resolution pressure data logger deployed at 857D in June, 2010.

Warm-season severe wind events in Germany

Science.gov (United States)

Gatzen, Christoph

2013-04-01

A 15-year data set of wind measurements was analyzed with regard to warm season severe wind gusts in Germany. For April to September of the years 1997 to 2011, 1035 wind measurements of 26 m/s or greater were found. These wind reports were associated with 268 wind events. In total, 252 convective wind events contributed to 837 (81%) of the wind reports, 16 non-convective synoptic-scale wind events contributed to 198 reports (19%). Severe wind events were found with synoptic situations characterized by rather strong mid-level flow and advancing mid-level troughs. Severe convective wind events were analyzed using radar images and classified with respect to the observed radar structure. The most important convective mode was squall lines that were associated with one third of all severe wind gusts, followed by groups, bow echo complexes, and bow echoes. Supercells and cells were not associated with many wind reports. The low contribution of isolated cells indicates that rather large-scale forcing by synoptic-scale features like fronts is important for German severe wind events. Bow echoes were found to be present for 58% of all wind reports. The movement speed of bow echoes indicated a large variation with a maximum speed of 33 m/s. Extreme wind events as well as events with more than 15 wind reports were found to be related to higher movement speeds. Concentrating on the most intense events, derechos seem to be very important to the warm season wind threat in Germany. Convective events with a path length of more than 400 km contributed to 36% of all warm-season wind gusts in this data set. Furthermore, eight of nine extreme gusts exceeding 40 m/s were recorded with derecho events.

Evolution of wave turbulence under "gusty" forcing.

Science.gov (United States)

Annenkov, S Y; Shrira, V I

2011-09-09

We consider nonlinear evolution of a random wave field under gusty forcing, fluctuating around a constant mean. Here the classical wave turbulence theory that assumes a proximity to stationarity is not applicable. We show by direct numerical simulation that the self-similarity of wave field evolution survives under fluctuating forcing. The wave field statistical characteristics averaged over fluctuations of forcing evolve as if there were a certain constant "effective wind." The results justify the use of the kinetic equations with forcing averaged over gusts as a good first approximation.

The future of wind energy

International Nuclear Information System (INIS)

Koughnett, K. Van

2003-01-01

This presentation provided a brief history of wind power through the ages, and culminated with a look at installed capacity in 2002. Vision Quest has been in the wind power business since 1980, and the first turbines were installed in 1997. The company operates 40 per cent of Canada's wind capacity. Vision Quest became part of TransAlta in December 2002, the largest non-regulated electric generation and marketing company in Canada. The reasons for investing in wind power were briefly reviewed. The author then examined the physics of wind power and wind energy resources. The key resource issues were identified as being resource availability and constancy, which is similar to oil and gas exploration. Utility scale turbines were described. The pros and cons of larger turbines were compared, and it was shown that larger turbines offer better economics, a higher capacity factor and fewer turbines to permit. Manufacturers are focused on larger machines for offshore. The various permitting authorities and their areas of responsibility were listed, from municipal, provincial and federal levels. The key drivers are: wind speed, installed cost of equipment, revenue, operating expense, and financial expense. Project risks include: power purchase agreements, technology risk, financial risk, construction risk, regulation, operating risks, dependence on third parties, and reliance on advisors. Some of the challenges facing Vision Quest are being early, permitting, electric grid interconnection, openness of markets, market supply, demand forces, and getting capital costs down. tabs., figs

Dispersal of Sediment in the Western Adriatic during Energetic Wintertime Forcing

Science.gov (United States)

Harris, C. K.; Sherwood, C. R.; Mullenbach, B. L.; Pullen, J. D.

2003-12-01

EuroSTRATAFORM aims to relate sediment delivery and reworking to seabed morphology and stratigraphy through observations and modeling of water column transport. The Po River dominates buoyancy and sediment input into the Adriatic Sea, but small Apeninne rivers (the Chienti, Pescara, etc.) may produce locally important signals. Sedimentation is influenced by fluvial supply, resuspension by waves and currents, and transport by oceanographic currents forced by winds and buoyancy. Transport is likely highest during times of energetic forcing; including Bora events with northeasterly winds and Sirocco events with southeasterly winds. It is difficult, from field measurements alone, to characterize dispersal and convergence patterns over the relevant spatial scales. We applied a three-dimensional hydrodynamic model that includes fluvial delivery, transport, resuspension, and deposition of sediment to quantify sediment dispersal with a 2-km resolution over the entire Adriatic. Circulation calculations were driven by spatially- and temporally-varying wind fields for the Fall / Winter of 2002 / 2003 and realistic Po and Apennine river discharges. Waves were hindcast with the SWAN model. Dispersion of both resuspended and river-derived sediment was estimated for periods that contained intense Bora and Sirocco winds. Predicted sediment dispersal rates and patterns are sensitive to forcing winds, buoyancy flux, and wave patterns. Higher sediment flux was predicted during Bora conditions than during Sirocco conditions. Sirocco winds weaken the Western Adriatic Coastal Current (WACC), and because they tend to concentrate over the Eastern Adriatic, they often fail to create especially energetic waves in the Western Adriatic. Bora wind conditions, on the other hand, intensify the WACC and can build high wave energies over the northwestern Adriatic. Most of the sediment transport occurs during Bora, with a net southward flux. These predictions will be compared to field observations

Current-induced forces: a simple derivation

International Nuclear Information System (INIS)

Todorov, Tchavdar N; Dundas, Daniel; Lü, Jing-Tao; Brandbyge, Mads; Hedegård, Per

2014-01-01

We revisit the problem of forces on atoms under current in nanoscale conductors. We derive and discuss the five principal kinds of force under steady-state conditions from a simple standpoint that—with the help of background literature—should be accessible to physics undergraduates. The discussion aims at combining methodology with an emphasis on the underlying physics through examples. We discuss and compare two forces present only under current—the non-conservative electron wind force and a Lorentz-like velocity-dependent force. It is shown that in metallic nanowires both display significant features at the wire surface, making it a candidate for the nucleation of current-driven structural transformations and failure. Finally we discuss the problem of force noise and the limitations of Ehrenfest dynamics. (paper)

Use of a magnetic force exciter to vibrate a piezocomposite generating element in a small-scale windmill

International Nuclear Information System (INIS)

Luong, Hung Truyen; Goo, Nam Seo

2012-01-01

A piezocomposite generating element (PCGE) can be used to convert ambient vibrations into electrical energy that can be stored and used to power other devices. This paper introduces a design of a magnetic force exciter for a small-scale windmill that vibrates a PCGE to convert wind energy into electrical energy. A small-scale windmill was designed to be sensitive to low-speed wind in urban regions for the purpose of collecting wind energy. The magnetic force exciter consists of exciting magnets attached to the device’s input rotor and a secondary magnet fixed at the tip of the PCGE. The PCGE is fixed to a clamp that can be adjusted to slide on the windmill’s frame in order to change the gap between exciting and secondary magnets. Under an applied wind force, the input rotor rotates to create a magnetic force interaction that excites the PCGE. The deformation of the PCGE enables it to generate electric power. Experiments were performed with different numbers of exciting magnets and different gaps between the exciting and secondary magnets to determine the optimal configuration for generating the peak voltage and harvesting the maximum wind energy for the same range of wind speeds. In a battery-charging test, the charging time for a 40 mA h battery was approximately 3 h for natural wind in an urban region. The experimental results show that the prototype can harvest energy in urban regions with low wind speeds and convert the wasted wind energy into electricity for city use. (paper)

InSAR Time Series Analysis and Geophysical Modeling of City Uplift Associated with Geothermal Drillings in Staufen im Breisgau, Germany

Science.gov (United States)

Motagh, M.; Lubitz, C.

2014-12-01

Geothermal energy is of increasing importance as alternative, environmentally friendly technology for heat management. Direct interaction with the subsurface requires careful implementation, in particular in geological complex regions. The historical city Staufen im Breisgau, SW Germany, has attracted national attention as a case of implementation failure with severe consequences, causing debates on the applicability and security of this sustainable technique. Located at the eastern transition zone of the Upper Rhine Graben and the Schwarzwald massif, the geothermal potential is high at Staufen due to strong temperature gradients. In September 2007, seven boreholes for geothermal probes were drilled up to a depth of 140 m to provide a new heat management for the city hall. Within five years an uplift phenomenon has been observed in Staufen reaching more than 40 cm in places and 269 buildings were damaged. Hydro-chemical driven anhydrite-gypsum transformation in the subsurface was identified as the cause leading to volume increase that is observable as surface uplift. This process is associated with the geothermal drilling activities that have crossed several groundwater levels. In this work, we summarize and present the findings of spaceborne Synthetic Aperture Radar Interferometry (InSAR) analysis of the uplift in Staufen over the last five years from July 2008 through July 2013. By applying the Small Baseline Subset (SBAS) method, we find a localized elliptical-shaped deformation field in NE-SW orientation. Area of maximum uplift is located 50 m NNE of the drilling zone. At this location, we observe a cumulative uplift of approx. 13.7 cm ± 0.34 cm (mean value within an area of 30 m by 30 m) from July 2008 to July 2009, which reduced to cumulative uplift of 3 cm ± 0.25 cm from July 2012 to July 2013. The deceleration can be related to applied countermeasures as borehole sealing and groundwater pumping. The observed ground surface response was compared to

Turbulent wind waves on a water current

Directory of Open Access Journals (Sweden)

M. V. Zavolgensky

2008-05-01

Full Text Available An analytical model of water waves generated by the wind over the water surface is presented. A simple modeling method of wind waves is described based on waves lengths diagram, azimuthal hodograph of waves velocities and others. Properties of the generated waves are described. The wave length and wave velocity are obtained as functions on azimuth of wave propagation and growth rate. Motionless waves dynamically trapped into the general picture of three dimensional waves are described. The gravitation force does not enter the three dimensional of turbulent wind waves. That is why these waves have turbulent and not gravitational nature. The Langmuir stripes are naturally modeled and existence of the rogue waves is theoretically proved.

Rapid ice unloading in the Fleming Glacier region, southern Antarctic Peninsula, and its effect on bedrock uplift rates

DEFF Research Database (Denmark)

Zhao, Chen; King, Matt A.; Watson, Christopher S.

2017-01-01

deformation. We subtract modeled elastic deformation rates, and a suite of modeled viscous rates, from GPS-derived three-dimensional bedrock velocities at sites to the south of Fleming Glacier to infer properties of Earth rheology. Assuming the pre-breakup bedrock uplift was positive due to post-Last Glacial...... Maximum (LGM) ice retreat, our viscoelastic-corrected GPS uplift rates suggest upper mantle viscosities are >2×1019 Pas and likely >1×1020 Pas in this region, 1–2 orders of magnitude greater than previously found for the northern Antarctic Peninsula. Horizontal velocities at the GPS site nearest...

Wind profiler installed in Antarctica

Science.gov (United States)

Balsley, B. B.; Carey, J.; Woodman, R. F.; Sarango, M.; Urbina, J.; Rodriguez, R.; Ragaini, E.

A VHF (50 MHz) wind profiler was installed in Antarctica at the Peruvian Base “Machu Picchu” on King George Island from January 21 to 26. The wind profiler will provide a first look at atmospheric dynamics over the region.The profiler—the first of its kind in Antarctica—is a National Science Foundationsponsored cooperative project of the University of Colorado, the Geophysical Institute of Peru, the University of Piura (Peru), and the Peruvian Navy. This venture was also greatly facilitated by Peru's Comision Nacional de Asuntos Antartidos and Consejo Nacional de Ciencias y Tecnologia, with additional logis tics support provided by the Argentinean Navy and the Uruguayan Air Force.

Wind Regimes in Complex Terrain of the Great Valley of Eastern Tennessee

Energy Technology Data Exchange (ETDEWEB)

Birdwell, Kevin R. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

2011-05-01

This research was designed to provide an understanding of physical wind mechanisms within the complex terrain of the Great Valley of Eastern Tennessee to assess the impacts of regional air flow with regard to synoptic and mesoscale weather changes, wind direction shifts, and air quality. Meteorological data from 2008 2009 were analyzed from 13 meteorological sites along with associated upper level data. Up to 15 ancillary sites were used for reference. Two-step complete linkage and K-means cluster analyses, synoptic weather studies, and ambient meteorological comparisons were performed to generate hourly wind classifications. These wind regimes revealed seasonal variations of underlying physical wind mechanisms (forced channeled, vertically coupled, pressure-driven, and thermally-driven winds). Synoptic and ambient meteorological analysis (mixing depth, pressure gradient, pressure gradient ratio, atmospheric and surface stability) suggested up to 93% accuracy for the clustered results. Probabilistic prediction schemes of wind flow and wind class change were developed through characterization of flow change data and wind class succession. Data analysis revealed that wind flow in the Great Valley was dominated by forced channeled winds (45 67%) and vertically coupled flow (22 38%). Down-valley pressure-driven and thermally-driven winds also played significant roles (0 17% and 2 20%, respectively), usually accompanied by convergent wind patterns (15 20%) and large wind direction shifts, especially in the Central/Upper Great Valley. The behavior of most wind regimes was associated with detectable pressure differences between the Lower and Upper Great Valley. Mixing depth and synoptic pressure gradients were significant contributors to wind pattern behavior. Up to 15 wind classes and 10 sub-classes were identified in the Central Great Valley with 67 joined classes for the Great Valley at-large. Two-thirds of Great Valley at-large flow was defined by 12 classes. Winds

Diode Laser Assisted Filament Winding of Thermoplastic Matrix Composites

Directory of Open Access Journals (Sweden)

Claudia Prosperi

2010-01-01

Full Text Available A new consolidation method for the laser-assisted filament winding of thermoplastic prepregs is discussed: for the first time a diode laser is used, as well as long glass fiber reinforced polypropylene prepregs. A consolidation apparatus was built by means of a CNC motion table, a stepper motor and a simple tensioner. Preliminary tests were performed in a hoop winding configuration: only the winding speed was changed, and all the other process parameters (laser power, distance from the laser focus, consolidation force were kept constant. Small wound rings with an internal diameter of 25 mm were produced and compression tests were carried out to evaluate the composite agglomeration in dependence of the winding speed. At lower winding speeds, a stronginterpenetration of adjacent layers was observed.

Interferograms showing land subsidence and uplift in Las Vegas Valley, Nevada, 1992-99

Science.gov (United States)

Pavelko, Michael T.; Hoffmann, Jörn; Damar, Nancy A.

2006-01-01

The U.S. Geological Survey, in cooperation with the Nevada Department of Conservation and Natural Resources-Division of Water Resources and the Las Vegas Valley Water District, compiled 44 individual interferograms and 1 stacked interferogram comprising 29 satellite synthetic aperture radar acquisitions of Las Vegas Valley, Nevada, from 1992 to 1999. The interferograms, which depict short-term, seasonal, and long-term trends in land subsidence and uplift, are viewable with an interactive map. The interferograms show that land subsidence and uplift generally occur in localized areas, are responsive to ground-water pumpage and artificial recharge, and, in part, are fault controlled. Information from these interferograms can be used by water and land managers to mitigate land subsidence and associated damage. Land subsidence attributed to ground-water pumpage has been documented in Las Vegas Valley since the 1940s. Damage to roads, buildings, and other engineered structures has been associated with this land subsidence. Land uplift attributed to artificial recharge and reduced pumping has been documented since the 1990s. Measuring these land-surface changes with traditional benchmark and Global Positioning System surveys can be costly and time consuming, and results typically are spatially and temporally sparse. Interferograms are relatively inexpensive and provide temporal and spatial resolutions previously not achievable. The interferograms are viewable with an interactive map. Landsat images from 1993 and 2000 are viewable for frames of reference to locate areas of interest and help determine land use. A stacked interferogram for 1992-99 is viewable to visualize the cumulative vertical displacement for the period represented by the individual interferograms. The interactive map enables users to identify and estimate the magnitude of vertical displacement, visually analyze deformation trends, and view interferograms and Landsat images side by side. The

Comparison of the ocean surface vector winds from atmospheric reanalysis and scatterometer-based wind products over the Nordic Seas and the northern North Atlantic and their application for ocean modeling

Science.gov (United States)

Dukhovskoy, Dmitry S.; Bourassa, Mark A.; Petersen, Gudrún Nína; Steffen, John

2017-03-01

Ocean surface vector wind fields from reanalysis data sets and scatterometer-derived gridded products are analyzed over the Nordic Seas and the northern North Atlantic for the time period from 2000 to 2009. The data sets include the National Center for Environmental Prediction Reanalysis 2 (NCEPR2), Climate Forecast System Reanalysis (CFSR), Arctic System Reanalysis (ASR), Cross-Calibrated Multiplatform (CCMP) wind product version 1.1 and recently released version 2.0, and QuikSCAT. The goal of the study is to assess discrepancies across the wind vector fields in the data sets and demonstrate possible implications of these differences for ocean modeling. Large-scale and mesoscale characteristics of winds are compared at interannual, seasonal, and synoptic timescales. A cyclone tracking methodology is developed and applied to the wind fields to compare cyclone characteristics in the data sets. Additionally, the winds are evaluated against observations collected from meteorological buoys deployed in the Iceland and Irminger Seas. The agreement among the wind fields is better for longer time and larger spatial scales. The discrepancies are clearly apparent for synoptic timescales and mesoscales. CCMP, ASR, and CFSR show the closest overall agreement with each other. Substantial biases are found in the NCEPR2 winds. Numerical sensitivity experiments are conducted with a coupled ice-ocean model forced by different wind fields. The experiments demonstrate differences in the net surface heat fluxes during storms. In the experiment forced by NCEPR2 winds, there are discrepancies in the large-scale wind-driven ocean dynamics compared to the other experiments.

Jet Exit Rig Six Component Force Balance

Science.gov (United States)

Castner, Raymond; Wolter, John; Woike, Mark; Booth, Dennis

2012-01-01

A new six axis air balance was delivered to the NASA Glenn Research Center. This air balance has an axial force capability of 800 pounds, primary airflow of 10 pounds per second, and a secondary airflow of 3 pounds per second. Its primary use was for the NASA Glenn Jet Exit Rig, a wind tunnel model used to test both low-speed, and high-speed nozzle concepts in a wind tunnel. This report outlines the installation of the balance in the Jet Exit Rig, and the results from an ASME calibration nozzle with an exit area of 8 square-inches. The results demonstrated the stability of the force balance for axial measurements and the repeatability of measurements better than 0.20 percent.

Observational study of surface wind along a sloping surface over mountainous terrain during winter

Science.gov (United States)

Lee, Young-Hee; Lee, Gyuwon; Joo, Sangwon; Ahn, Kwang-Deuk

2018-03-01

The 2018 Winter Olympic and Paralympic Games will be held in Pyeongchang, Korea, during February and March. We examined the near surface winds and wind gusts along the sloping surface at two outdoor venues in Pyeongchang during February and March using surface wind data. The outdoor venues are located in a complex, mountainous terrain, and hence the near-surface winds form intricate patterns due to the interplay between large-scale and locally forced winds. During February and March, the dominant wind at the ridge level is westerly; however, a significant wind direction change is observed along the sloping surface at the venues. The winds on the sloping surface are also influenced by thermal forcing, showing increased upslope flow during daytime. When neutral air flows over the hill, the windward and leeward flows show a significantly different behavior. A higher correlation of the wind speed between upper- and lower-level stations is shown in the windward region compared with the leeward region. The strong synoptic wind, small width of the ridge, and steep leeward ridge slope angle provide favorable conditions for flow separation at the leeward foot of the ridge. The gust factor increases with decreasing surface elevation and is larger during daytime than nighttime. A significantly large gust factor is also observed in the leeward region.

A comparison between the dynamics of horizontal and vertical axis offshore floating wind turbines.

Science.gov (United States)

Borg, M; Collu, M

2015-02-28

The need to further exploit offshore wind resources in deeper waters has led to a re-emerging interest in vertical axis wind turbines (VAWTs) for floating foundation applications. However, there has been little effort to systematically compare VAWTs to the more conventional horizontal axis wind turbine (HAWT). This article initiates this comparison based on prime principles, focusing on the turbine aerodynamic forces and their impact on the floating wind turbine static and dynamic responses. VAWTs generate substantially different aerodynamic forces on the support structure, in particular, a potentially lower inclining moment and a substantially higher torque than HAWTs. Considering the static stability requirements, the advantages of a lower inclining moment, a lower wind turbine mass and a lower centre of gravity are illustrated, all of which are exploitable to have a less costly support structure. Floating VAWTs experience increased motion in the frequency range surrounding the turbine [number of blades]×[rotational speed] frequency. For very large VAWTs with slower rotational speeds, this frequency range may significantly overlap with the range of wave excitation forces. Quantitative considerations are undertaken comparing the reference NREL 5 MW HAWT with the NOVA 5 MW VAWT. © 2015 The Author(s) Published by the Royal Society. All rights reserved.

Dynamically sequestered F-term uplifting in extra dimension

International Nuclear Information System (INIS)

Abe, Hiroyuki; Higaki, Tetsutaro; Kobayashi, Tatsuo; Omura, Yuji

2008-01-01

We study moduli stabilization, the dynamical supersymmetry (SUSY) breaking, the uplifting of SUSY anti-de Sitter (AdS) vacuum and the sequestering of hidden sector in a five-dimensional supergravity model, where all modes of the visible sector and the hidden sector are originated from bulk fields. We clarify couplings between the visible and hidden sectors. The expressions for the visible sector soft SUSY breaking terms as well as the hidden sector potential are shown explicitly in our model. The sequestering is achieved dynamically by a wavefunction localization in extra dimension. We find that the tree-level soft scalar mass and the A-term can be suppressed at a SUSY breaking Minkowski minimum where the radius modulus is stabilized, while gaugino masses would be a mirage type

Optimization design of blade shapes for wind turbines

DEFF Research Database (Denmark)

Chen, Jin; Wang, Xudong; Shen, Wen Zhong

2010-01-01

For the optimization design of wind turbines, the new normal and tangential induced factors of wind turbines are given considering the tip loss of the normal and tangential forces based on the blade element momentum theory and traditional aerodynamic model. The cost model of the wind turbines...... and the optimization design model are developed. In the optimization model, the objective is the minimum cost of energy and the design variables are the chord length, twist angle and the relative thickness. Finally, the optimization is carried out for a 2 MW blade by using this optimization design model....... The performance of blades is validated through the comparison and analysis of the results. The reduced cost shows that the optimization model is good enough for the design of wind turbines. The results give a proof for the design and research on the blades of large scale wind turbines and also establish...

Post-Palaeozoic uplift history of southeastern Australia revisited: results from a process-based mode of landscape evolution

International Nuclear Information System (INIS)

Van Der Beek, P.A.; Braun, J.; Lambeck, K.

1999-01-01

Developments over the last decade in the debate concerning the geomorphic evolution of the south-eastern Australian highlands are reviewed, taking as a starting point the model of passive denudation and isostatic rebound of a Palaeozoic mountain belt presented by Lambeck and Stephenson (1986). This model has been popular in the geomorphological community because it provides a quantitative framework to explain the very low rates of landscape evolution inferred from most geomorphological studies. The model has, however, also been criticised for its treatment of erosion as being linearly dependent on elevation, as well as for its predictions of regional uplift and denudation patterns that are not in accord with inferences from fission-track thermochronological data. Part of controversy stems from conceptual misunderstandings on the interpretation of data and from insufficient consideration of questions of spatial and temporal scale. First results of a new physical process-based model for large-scale long-term landscape evolution in the south-eastern highlands are presented. These show that the denudation history and drainage development of south-eastern Australia can be explained to a first order without invoking large-scale mid-Cretaceous or Tertiary uplift events. The model predicts drainage patterns in southeastern Australia to have evolved by rearrangement of an initially north-westerly directed drainage net, caused by drops in base-level during Mesozoic rifting along the southern and eastern margins of the study region. The geomorphology and available fission-track data in the Snowy Mountains region (and possibly also in the Bathurst - Blue Mountains region) do require renewed (mid Cretaceous?) uplift to have taken place. The model results are discussed in the light of recent controversies surrounding the southeastern highlands-their uplift history, denudation rates, depth of denudation of the coastal strip and inferred Mesozoic drainage patterns. Copyright (1999

A late Eocene palynological record of climate change and Tibetan Plateau uplift (Xining Basin, China)

NARCIS (Netherlands)

Hoorn, C.; Straathof, J.; Abels, H.A.; Xu, Y.; Utescher, T.; Dupont-Nivet, G.

2012-01-01

Climate models suggest that Asian paleoenvironments, monsoons and continental aridification were primarily governed by tectonic uplift and sea retreat since the Eocene with potential contribution of global climate changes. However, the cause and timing of these paleoenvironmental changes remain

The physics of wind-blown sand and dust.

Science.gov (United States)

Kok, Jasper F; Parteli, Eric J R; Michaels, Timothy I; Karam, Diana Bou

2012-10-01

The transport of sand and dust by wind is a potent erosional force, creates sand dunes and ripples, and loads the atmosphere with suspended dust aerosols. This paper presents an extensive review of the physics of wind-blown sand and dust on Earth and Mars. Specifically, we review the physics of aeolian saltation, the formation and development of sand dunes and ripples, the physics of dust aerosol emission, the weather phenomena that trigger dust storms, and the lifting of dust by dust devils and other small-scale vortices. We also discuss the physics of wind-blown sand and dune formation on Venus and Titan.

230Th/234U dating of coral limestones and vertical uplift at Djibouti

International Nuclear Information System (INIS)

Faure, Hugues; Hoang, C.T.; Lalou, Claude

1980-01-01

Coral limestones sampled from marine terraces along the Afar coast have been dated by the 230 Th/ 234 U method. The ages confirm the stratigraphic unity of these formations and the existence of the paleo sea level dated 124 000 years ago in this region. These results permit to deduce the uplift rates of this littoral [fr

Wyrtki Jets: Role of Intraseasonal forcing

Indian Academy of Sciences (India)

44

2018-04-16

Apr 16, 2018 ... and global climate system (Vinayachandran et al., 1999; Murtugudde and .... wind forcing influence the WJs? and how does this relate to its observed ...... Lau, K., and H. Wu, 2010: Characteristics of precipitation, cloud, and la-.

The influence of humidity fluxes on offshore wind speed profiles

DEFF Research Database (Denmark)

Barthelmie, Rebecca Jane; Sempreviva, Anna Maria; Pryor, Sara

2010-01-01

extrapolation from lower measurements. With humid conditions and low mechanical turbulence offshore, deviations from the traditional logarithmic wind speed profile become significant and stability corrections are required. This research focuses on quantifying the effect of humidity fluxes on stability corrected...... wind speed profiles. The effect on wind speed profiles is found to be important in stable conditions where including humidity fluxes forces conditions towards neutral. Our results show that excluding humidity fluxes leads to average predicted wind speeds at 150 m from 10 m which are up to 4% higher...... than if humidity fluxes are included, and the results are not very sensitive to the method selected to estimate humidity fluxes....

Hybrid damper with stroke amplification for damping of offshore wind turbines

DEFF Research Database (Denmark)

Brodersen, Mark L.; Høgsberg, Jan

2016-01-01

tower. The proposed hybrid damper consists of a passive viscous dashpot placed in series with a load cell and an active actuator. By integrated force feedback control of the actuator motion, the associated displacement amplitude over the viscous damper can be increased compared with the passive viscous......The magnitude of tower vibrations of offshore wind turbines is a key design driver for the feasibility of the monopilesupport structure. A novel control concept for the damping of these tower vibrations is proposed, where viscous-type hybrid dampers are installed at the bottom of the wind turbine...... case, hereby significantly increasing the feasibility of viscous dampers acting at the bottom of the wind turbine tower. To avoid drift in the actuator displacement, a filtered time integration of the measured force signal is introduced. Numerical examples demonstrate that the filtered time integration...

Geomorphic Evidence of a Complex late-Cenozoic Uplift and Lateral Displacement History Along the 2013 M7.7 Baluchistan, Pakistan Strike-slip Rupture

Science.gov (United States)

Harbor, D. J.; Barnhart, W. D.

2017-12-01

The 2013 M7.7 Baluchistan earthquake in southern Pakistan ruptured 200 km of the north-dipping Hoshab reverse fault with dominantly lateral motion, clearly at odds with the regional topography created by previous reverse fault offsets. The kinematics of this earthquake led to the hypotheses that the Hoshab fault may alternatively slip in a reverse and lateral sense (bi-modal slip), and that the southeast Makran rotates as a uniform block around the fault (ball-and-socket rotation). Here, we use river profiles, regional relief, fault locations, and detailed geomorphic maps derived from optical imagery and DEMs to evaluate the recent uplift history of this region. We find that late Cenozoic fault zone geomorphology supports a spatially complex transition from lateral-dominated offsets in the NE to reverse-dominated offsets in the SW. Additionally, fault zone geomorphology suggests that the location of the Hoshab fault itself may change through time, leading to active incision of footwall alluvial fans and pediments. Stream profiles likewise record incision patterns that vary along the Hoshab fault. Incision and deposition in the SW are illustrative of relative footwall subsidence, consistent with recent uplift on the Hoshab fault; whereas incision and deposition in the NE are illustrative of relative footwall uplift consistent with ongoing regional uplift due to ball-and-socket rotations and dominantly lateral offsets along the northern Hoshab fault. The largest streams also record multiple, discrete, base-level drops, including the presence of convex-up river profiles in the hanging wall of the Hoshab fault. These profiles along hanging wall streams highlight a complex spatial and temporal history of reverse offset, lateral channel offset, and base-level resetting in regional streams that are altogether inconsistent with the kinematics of the 2013 earthquake alone, but that are consistent with the bi-modal slip model. Additionally, the evidence of footwall uplift in

Aero-acoustic Computations of Wind Turbines

DEFF Research Database (Denmark)

Shen, Wen Zhong; Michelsen, Jess; Sørensen, Jens Nørkær

2002-01-01

A numerical algorithm for acoustic noise generation is extended to 3D flows. The approach involves two parts comprising a viscous incompressible flow part and an inviscid acoustic part. In order to simulate noise generated from a wind turbine, the incompressible and acoustic equations are written...... in polar coordinates. The developed algorithm is combined with a so-called actuator-line technique in which the loading is distributed along lines representing the blade forces. Computations are carried out for the 500kW Nordtank wind turbine equipped with three LM19 blades. ©2001 The American Institute...

Wind Turbine Wake in Atmospheric Turbulence

DEFF Research Database (Denmark)

Réthoré, Pierre-Elouan Mikael

to calibrate faster and simpler engineering wind farm wake models. The most attractive solution was the actuator disc method with the steady state k-ε turbulence model. The first step to design such a tool is the treatment of the forces. This thesis presents a computationally inexpensive method to apply......) shows that the problem mainly comes from the assumptions of the eddy-viscosity concept, which are deeply invalidated in the wind turbine wake region. Different models that intent to correct the k-ε model’s issues are investigated, of which none of them is found to be adequate. The mixing of the wake...

Accidental inflation from Kähler uplifting

Energy Technology Data Exchange (ETDEWEB)

Ben-Dayan, Ido; Westphal, Alexander; Wieck, Clemens [Deutsches Elektronen-Synchrotron DESY, Theory Group, Notkestrasse 85, D-22603 Hamburg (Germany); Jing, Shenglin, E-mail: ido.bendayan@desy.de, E-mail: shenglin.jing@utoronto.ca, E-mail: alexander.westphal@desy.de, E-mail: clemens.wieck@desy.de [Canadian Institute for Theoretical Astrophysics, University of Toronto, 60 St.George Street, Toronto, ON, M5S 3H8 (Canada)

2014-03-01

We analyze the possibility of realizing inflation with a subsequent dS vacuum in the Käahler uplifting scenario. The inclusion of several quantum corrections to the 4d effective action evades previous no-go theorems and allows for construction of simple and successful models of string inflation. The predictions of several benchmark models are in accord with current observations, i.e., a red spectral index, negligible non-gaussianity, and spectral distortions similar to the simplest models of inflation. A particularly interesting subclass of models are ''left-rolling'' ones, where the overall volume of the compactified dimensions shrinks during inflation. We call this phenomenon ''inflation by deflation'' (IBD), where deflation refers to the internal manifold. This subclass has the appealing features of being insensitive to initial conditions, avoiding the overshooting problem, and allowing for observable running α ∼ 0.012 and enhanced tensor-to-scalar ratio r ∼ 10{sup −5}. The latter results differ significantly from many string inflation models.

Analyzing the effect of large rotations on the seismic response of structures subjected to foundation local uplift

Directory of Open Access Journals (Sweden)

El Abbas N.

2016-01-01

Full Text Available This work deals with seismic analysis of structures by taking into account soil-structure interaction where the structure is modeled by an equivalent flexible beam mounted on a rigid foundation that is supported by a Winkler like soil. The foundation is assumed to undergo local uplift and the rotations are considered to be large. The coupling of the system is represented by a series of springs and damping elements that are distributed over the entire width of the foundation. The non-linear equations of motion of the system were derived by taking into account the equilibrium of the coupled foundation-structure system where the structure was idealized as a single-degree-of-freedom. The seismic response of the structure was calculated under the occurrence of foundation uplift for both large and small rotations. The non-linear differential system of equations was integrated by using the Matlab command ode15s. The maximum response has been determined as function of the intensity of the earthquake, the slenderness of the structure and the damping ratio. It was found that considering local uplift with small rotations of foundation under seismic loading leads to unfavorable structural response in comparison with the case of large rotations.

Origins of the Asian-Australian monsoons related to Cenozoic plate movement and Tibetan Plateau uplift - A modeling study

Science.gov (United States)

Liu, X.; Dong, B.; Yin, Z. Y.; Smith, R. S.; Guo, Q.

2017-12-01

The origin of monsoon is a subject that has attracted much attention in the scientific community and even today it is still controversial. According to geological records, there is conflicting evidence regarding the timings of establishment of the monsoon climates in South Asia, East Asia, and northern Australia. Additionally, different explanations for the monsoon origins have been derived from various numerical simulations. To further investigate the origin and evolution of the Asian and Australian monsoons, we designed a series of numerical experiments using a coupled atmospheric-oceanic general circulation model. Since the Indian-Australian plate has shifted its position significantly during the Cenozoic, together with the large-scale uplift of the Tibetan Plateau (TP), in these experiments we considered the configurations of ocean-land masses and large topographic features based on geological evidence of plate motion and TP uplift in 5 typical Cenozoic geological periods: mid-Paleocene ( 60Ma), late-Eocene ( 40Ma), late-Oligocene ( 25Ma), late-Miocene ( 10Ma), and present day. These experiments allowed us to examine the combined effects of the changes in the land-ocean configuration due to plate movement and TP uplift, they also provided insight into the effects of the high CO2 levels during the Eocene. The simulations revealed that during the Paleocene, the Indian Subcontinent was still positioned in the Southern Hemisphere (SH) and, therefore, its climate behaved as the SH tropical monsoon. By the late Eocene, it moved into the tropical Northern Hemisphere, which allowed the establishment of the South Asian monsoon. In contrast, the East Asian and Australian monsoon did not exist in the late Oligocene. These monsoon systems were established in the Miocene and then enhanced thereafter. Establishments of the low-latitude monsoons in South Asia and Australia were entirely determined by the position of the Indian-Australian plate and not related to the TP uplift

Phanerozoic burial, uplift and denudation of the Equatorial Atlantic margin of South America

Science.gov (United States)

Japsen, Peter; Bonow, Johan M.; Green, Paul F.; dall'Asta, Massimo; Roig, Jean-Yves; Theveniaut, Hervé

2017-04-01

We have initiated a study aimed at understanding the history of burial, uplift and denudation of the South American Equatorial Atlantic Margin (SAEAM Uplift) including the Guiana Shield to provide a framework for investigating the hydrocarbon prospectivity of the offshore region. We report first results including observations from fieldwork at the northern and southern flank of the Guiana Shield. The study combines apatite fission-track analysis (AFTA) and vitrinite reflectance data from samples of outcrops and drillcores, sonic velocity data from drill holes and stratigraphic landscape analysis (mapping of peneplains) - all constrained by geological evidence, following the methods of Green et al. (2013). The study will thus combine the thermal history from AFTA data with the denudation history from stratigraphic landscape analysis to provide magnitudes and timing of vertical movements (Japsen et al. 2012, 2016). Along the Atlantic margin of Suriname and French Guiana, tilted and truncated Lower Cretaceous strata rest on Precambrian basement (Sapin et al. 2016). Our AFTA data show that the basement underwent Mesozoic exhumation prior to deposition of the Lower Cretaceous cover. Sub-horizontal peneplains define the landscape of the Guiana Shield at elevations up to 500 m a.s.l. As these sub-horizontal peneplains truncate the tilted, sub-Cretaceous surface along the Atlantic margin, these peneplains were therefore formed and uplifted in post-Cretaceous time. This interpretation is in good agreement with our AFTA data that define Paleogene exhumation along the margin and with the results of Theveniaut and Freyssinet (2002) who used palaeomagnetic data to conclude that bauxitic surfaces across basement at up to 400 m a.s.l. on the Guiana Shield formed during the Palaeogene. Integration of the results from AFTA with stratigraphic landscape analysis (currently in progress) and geological evidence will provide a robust reconstruction of the tectonic development of the

Fatigue strength ofcomposite wind turbine blade structures

DEFF Research Database (Denmark)

Ardila, Oscar Gerardo Castro

Wind turbines are normally designed to withstand 20-30 years of life. During this period, the blades, which are the main rotating structures of a wind turbine, are subjected to high fluctuating load conditions as a result of a combination of gravity, inertia, and aeroelastic forces. For this reason......, fatigue is one of the foremost concerns during the design of these structures. However, current standard fatigue methods used for designing wind turbine blades seem not to be completely appropriate for these structures because they are still based on methods developed for metals and not for composite...... materials from which the blades are made. In this sense, the aim of this work is to develop more accurate and reliable fatigue-life prediction models for composite wind turbine blades. In this project, two types of fatigue models are implemented: fatigue-life models and damage mechanics models. In the first...

Wind wave source functions in opposing seas