Irrigation water quality influences heavy metal uptake by willows in biosolids.

Science.gov (United States)

Laidlaw, W Scott; Baker, Alan J M; Gregory, David; Arndt, Stefan K

2015-05-15

Phytoextraction is an effective method to remediate heavy metal contaminated landscapes but is often applied for single metal contaminants. Plants used for phytoextraction may not always be able to grow in drier environments without irrigation. This study investigated if willows (Salix x reichardtii A. Kerner) can be used for phytoextraction of multiple metals in biosolids, an end-product of the wastewater treatment process, and if irrigation with reclaimed and freshwater influences the extraction process. A plantation of willows was established directly onto a tilled stockpile of metal-contaminated biosolids and irrigated with slightly saline reclaimed water (EC ∼2 dS/cm) at a wastewater processing plant in Victoria, Australia. Biomass was harvested annually and analysed for heavy metal content. Phytoextraction of cadmium, copper, nickel and zinc was benchmarked against freshwater irrigated willows. The minimum irrigation rate of 700 mm per growing season was sufficient for willows to grow and extract metals. Increasing irrigation rates produced no differences in total biomass and also no differences in the extraction of heavy metals. The reclaimed water reduced both the salinity and the acidity of the biosolids significantly within the first 12 months after irrigation commenced and after three seasons the salinity of the biosolids had dropped to metal extraction. Reclaimed water irrigation reduced the biosolid pH and this was associated with reductions of the extraction of Ni and Zn, it did not influence the extraction of Cu and enhanced the phytoextraction of Cd, which was probably related to the high chloride content of the reclaimed water. Our results demonstrate that flood-irrigation with reclaimed water was a successful treatment to grow willows in a dry climate. However, the reclaimed water can also change biosolids properties, which will influence the effectiveness of willows to extract different metals. Copyright © 2015 Elsevier Ltd. All rights

Drying characteristics of willow chips and stems

NARCIS (Netherlands)

Gigler, J.K.; Loon, van W.K.P.; Seres, I.; Meerdink, G.; Coumans, W.J.

2000-01-01

In supply chains of willow (Salix viminalis) biomass to energy plants, drying is advisable in order to enable safe long-term storage, increase boiler efficiency and reduce gaseous emissions. To gain insight into the drying process, drying characteristics of willow chips and stems were investigated

Yield and Water Quality Impacts of Field-Scale Integration of Willow into a Continuous Corn Rotation System.

Science.gov (United States)

Zumpf, Colleen; Ssegane, Herbert; Negri, Maria Cristina; Campbell, Patty; Cacho, Julian

2017-07-01

Agricultural landscape design has gained recognition by the international environmental and development community as a strategy to address multiple goals in land, water, and ecosystem service management; however, field research is needed to quantify impacts on specific local environments. The production of bioenergy crops in specific landscape positions within a grain-crop field can serve the dual purpose of producing cellulosic biomass (nutrient recovery) while also providing regulating ecosystem services to improve water quality (nutrient reduction). The effectiveness of such a landscape design was evaluated by the strategic placement of a 0.8-ha short-rotation shrub willow ( Seemen) bioenergy buffer along marginal soils in a 6.5-ha corn ( L.) field in a 6-yr field study in central Illinois. The impact of willow integration on water quality (soil water, shallow groundwater leaching, and crop nutrient uptake) and quantity (soil moisture and transpiration) was monitored in comparison with corn in the willow's first cycle of growth. Willows significantly reduced nitrate leachate in shallow subsurface water by 88% while maintaining adequate nutrient and water usage. Results suggest that willows offer an efficient nutrient-reduction strategy and may provide additional ecosystem services and benefits, including enhanced soil health. However, low values for calculated willow biomass will need to be readdressed in the future as harvest data become available to understand contributing factors that affected productivity beyond nutrient availability. Copyright © by the American Society of Agronomy, Crop Science Society of America, and Soil Science Society of America, Inc.

Water tables constrain height recovery of willow on Yellowstone's northern range.

Science.gov (United States)

Bilyeu, Danielle M; Cooper, David J; Hobbs, N Thompson

2008-01-01

Excessive levels of herbivory may disturb ecosystems in ways that persist even when herbivory is moderated. These persistent changes may complicate efforts to restore ecosystems affected by herbivores. Willow (Salix spp.) communities within the northern range in Yellowstone National Park have been eliminated or degraded in many riparian areas by excessive elk (Cervus elaphus L.) browsing. Elk browsing of riparian willows appears to have diminished following the reintroduction of wolves (Canis lupis L.), but it remains uncertain whether reduced herbivory will restore willow communities. The direct effects of elk browsing on willows have been accompanied by indirect effects from the loss of beaver (Castor canadensis Kuhl) activity, including incision of stream channels, erosion of fine sediments, and lower water tables near streams historically dammed by beaver. In areas where these changes have occurred, lowered water tables may suppress willow height even in the absence of elk browsing. We conducted a factorial field experiment to understand willow responses to browsing and to height of water tables. After four years of protection from elk browsing, willows with ambient water tables averaged only 106 cm in height, with negligible height gain in two of three study species during the last year of the experiment. Willows that were protected from browsing and had artificially elevated water tables averaged 147 cm in height and gained 19 cm in the last year of the experiment. In browsed plots, elevated water tables doubled height gain during a period of slightly reduced browsing pressure. We conclude that water availability mediates the rate of willow height gain and may determine whether willows grow tall enough to escape the browse zone of elk and gain resistance to future elk browsing. Consequently, in areas where long-term beaver absence has resulted in incised stream channels and low water tables, a reduction in elk browsing alone may not be sufficient for recovery

Willow wood production on radionuclide polluted areas

Directory of Open Access Journals (Sweden)

Rodkin Oleg I.

2010-01-01

Full Text Available ABSTRACT: One of the key environmental problems in Belarus is effective use of agricultural lands contaminated by radionuclide due to the Chernobyl disaster. The alternative method to traditional agricultural crops is fast growing willow cultivation. It is possible to use biomass of willow as renewable energy source. The goal of our investigation was the estimation of environmental aspects of willow wood production on polluted areas. The field study experiments (2007-2010 were conducted at Krichev district of Mogilev region in eastern Belarus. This region characterized by high level of Cs-137 contamination as well as high level of heavy metals pollution. In the first stage of experiments, the concentration of cesium-137 in different parts of willow biomass had been measured and transfer factor calculated. The measuring had been done for leaves, roots, and wood. To control cesium-137 accumulation in willow biomass we apply different types (nitrogen N, phosphorus P and potassium K and dose of fertilizer. The experiments show that potassium mineral fertilizer is the key factor for radionuclide accumulation control. The optimal dose of potassium is 90 kg per hectare. On the base of experimental results the model of cesium-137 accumulation in the wood for a 21 year has been developed. In accordance with calculation to the end of willow cultivation (21 year concentration of cesium-137 in wood will not be higher than permitted even with the level of cesium-137 contamination in the soil 1480 kBq/m2 (maximum 140 kqB/m2 with permitted level for firewood is 740 Bq/kg.. The concentration of cesium-137 in the roots increases gradually and get maximum in 21 year (3000 kqB/m2. Our results confirm that in the sum about 0.8 million hectares of radionuclide polluted arable lands partly excluded from agricultural practice in Belarus could be used for willow biomass production.

Black Willow

Science.gov (United States)

R. M. Krinard

1980-01-01

Black willow and other species of Salix together comprise a majority of the stocking. Cottonwood is the chief associate, particularly in the early stages, but green ash, sycamore, pecan, persimmon, waterlocust, American elm, baldcypress, red maple, sugarberry, box-elder, and in some areas, silver maple are invaders preceding the next successional stage.

Biomass production in willows. What did we know before the energy crisis

Energy Technology Data Exchange (ETDEWEB)

Perttu, K L [ed.

1984-12-01

The biological foundations of biomass with willows originate in the experiences from basket willow husbandry. This was an established discipline in Europe in the 18th century. Problems concerning site preparation, selection of clones, planting as cuttings, spacing, weed control, rotation time, harvesting and coppicing vigour with respect to the longevity of the stand, were practically solved at the research level and already in practice. The yield potential of basket willow and willows for hoop production as well as yield figures from field experiments were quite high also according to present-day biomass willow experiments. An explanation of this could be the much higher stand densities than has been customary in current willow experiments. Although many practical questions got their answers in basket willow husbandry, open questions still remain. The basket willow era gave only little experience on willow production in peatlands; actually peatsoils were almost avoided. Knowledge of nutrient require ments and fertilization was also rather elementary. These aspects must therefore be established for biomass production. Control of weeds in the establishment phase of the willow husbandry was solved by manual work. Since this is a labour intensive method which is no longer possible, a more modern weed control needs to be developed for current husbandry. As a whole it is a task for related research to attach proper optimization of cultural techniques to suitable willow clones in order to attain and maintain as high a production level as was the case in the old basket willow husbandry. With 25 refs.

Results from software based empirical models of and standing biomass for poplar and willow grown as short rotation coppice

Energy Technology Data Exchange (ETDEWEB)

Baldwin, M.E.; Morgan, G.W.; Brewer, A.C. (Forest Research Biometrics, Surveys and Statistics Division, Forest Research, Wrecclesham (United Kingdom))

2007-07-01

Statistical analysis was used to create a model for estimating the quantity of biomass produced by crops of poplar and willow grown as short rotation coppice. This model was converted into a software system as described here. The software is currently available for scientific demonstration. (orig.)

Screening of willow species for resistance to heavy metals: comparison of performance in a hydroponics system and field trials.

Science.gov (United States)

Watson, C; Pulford, I D; Riddell-Black, D

2003-01-01

The aim of this study was to ascertain whether metal resistance in willow (Salix) clones grown in a hydroponics screening test correlated with data from the same clones grown independently in a field trial. If so, results from a short-term, glasshouse-based system could be extrapolated to the field, allowing rapid identification of willows suitable for planting in metal-contaminated substrates without necessitating longterm field trials. Principal Components Analysis was used to show groups of clones and to assess the relative importance of the parameters measured in both the hydroponics system and the field; including plant response factors such as increase in stem height, as well as metal concentrations in plant tissues. The clones tested fell into two distinct groups. Salix viminalis clones and the basket willow Black Maul (S. triandra) were less resistant to elevated concentrations of heavy metals than a group of hardier clones, including S. burjatica 'Germany,' S.x dasyclados, S. candida and S. spaethii. The more resistant clones produced more biomass in the glasshouse and field, and had higher metal concentrations in the wood. The less resistant clones had greater concentrations of Cu and Ni in the bark, and produced less biomass in the glasshouse and field. Significant relationships were found between the response of the same clones grown the in short-term glasshouse hydroponics system and in the field.

Treatment of landfill leachate by irrigation of willow coppice - Plant response and treatment efficiency

International Nuclear Information System (INIS)

Aronsson, Paer; Dahlin, Torleif; Dimitriou, Ioannis

2010-01-01

Landfill leachates usually need to be treated before discharged, and using soil-plant systems for this has gained substantial interest in Sweden and in the UK. A three-year field study was conducted in central Sweden to quantify plant response, treatment efficiency and impact on groundwater quality of landfill leachate irrigation of short-rotation willow coppice (Salix). Two willow varieties were tested and four irrigation regimes in sixteen 400-m 2 plots. The willow plants did not react negatively, despite very high annual loads of nitrogen (≤2160 kg N/ha), chloride (≤8600 kg Cl/ha) and other elements. Mean annual growth was 1.5, 9.8 and 12.6 tonnes DM/ha during years 1-3. For one of two willow varieties tested, relative leaf length accurately predicted growth rate. Irrigation resulted in elevated groundwater concentrations of all elements applied. Treatment efficiency varied considerably for different elements, but was adequate when moderate loads were applied. - Short-rotation willow coppice was successfully used for treating a strong landfill leachate in central Sweden over three years.

Yield of tannin willows on ravine areas in the Central Forest Steppe

Energy Technology Data Exchange (ETDEWEB)

Sidorov, A I

1981-01-01

A note on the performance of 12 species of willow grown in a plantation on leached chernozem soils, to provide bark rich in tannins. The plantation was established by cuttings (25 cm long) at a spacing of 2.5 x 0.5 metres for the tree willows and 2.5 x 0.75 metres for the bush willows. Bark yields were determined at 7-8 years. The greatest yields were obtained from Salix smithiana, S. stipularis and S. acuminata: 12.0, 10.8 and 10.2 t/hectare respectively. Data on tannin yields are tabulated. Fellings for bark harvesting can be made every 5 years in plantations of bush willows and every 7 years in plantations of tree willows. The plantations can be used for 30 year with bush willows and for 50 years with tree willows.

Foraging intention affects whether willow tits call to attract members of mixed-species flocks.

Science.gov (United States)

Suzuki, Toshitaka N; Kutsukake, Nobuyuki

2017-06-01

Understanding how individual behaviour influences the spatial and temporal distribution of other species is necessary to resolve the complex structure of species assemblages. Mixed-species bird flocks provide an ideal opportunity to investigate this issue, because members of the flocks are involved in a variety of behavioural interactions between species. Willow tits ( Poecile montanus ) often produce loud calls when visiting a new foraging patch to recruit other members of mixed-species flocks. The costs and benefits of flocking would differ with individual foraging behaviours (i.e. immediate consumption or caching); thus, willow tits may adjust the production of loud calls according to their foraging intention. In this study, we investigated the link between foraging decisions and calling behaviour in willow tits and tested its influence on the temporal cohesion with members of mixed-species flocks. Observations at experimental foraging patches showed that willow tits produced more calls when they consumed food items compared with when they cached them. Playback experiments revealed that these calls attracted flock members and helped to maintain their presence at foraging patches. Thus, willow tits adjusted calling behaviour according to their foraging intention, thereby coordinating the associations with members of mixed-species flocks. Our findings demonstrate the influence of individual decision-making on temporal cohesion with other species and highlight the importance of interspecific communication in mixed-species flocking dynamics.

Wolf presence and increased willow consumption by Yellowstone elk: implications for trophic cascades.

Science.gov (United States)

Creel, Scott; Christianson, David

2009-09-01

Recent increases in the height and growth ring width of willow (Salix spp.) and other woody plants in the Greater Yellowstone Ecosystem (GYE) have been attributed to a behaviorally mediated trophic cascade from wolves (Canis lupus) to elk (Cervus elaphus) to willows. This hypothesis predicts that individual elk consume less willow in response to the presence of wolves, but this prediction has not been directly tested with data from elk. We collected 727 fecal samples from elk in the Gallatin Canyon portion of the GYE over three winters and used microhistological methods to quantify the proportion of willow in each sample. We then tested the effect of wolf presence on willow consumption by elk, controlling for the effects of snow conditions, sex, and habitat type. During the period of study, 8-17 wolves occupied the study area, and wolves were locally present on 49% of 260 sampling days, stratified at two-week intervals across three drainages. Over the three years combined, willow consumption was related to snow conditions, wolf presence, and a wolf X sex interaction. As expected, willow consumption increased with deeper and less penetrable snow, and this effect was strong. Contrary to expectation, willow consumption increased in the presence of wolves. As with other aspects of antipredator behavior, wolves had different effects on willow consumption by males and females. Finally, we aggregated the data to estimate winter-long mean willow consumption within each drainage; at this broader scale, willow consumption again increased as predation risk increased. In summary, willow consumption was more strongly affected by snow conditions than by the presence of wolves. Interactions between elk and willow were affected by wolves, but not as predicted by the hypothesis that wolf presence favors willow release through a reduction in the selection of willow by individual elk. If a trophic cascade is operating, our results suggest that a decline in the size of the elk

Phytotoxicity of polycyclic aromatic hydrocarbons to willow trees

DEFF Research Database (Denmark)

Thygesen, R.S.; Trapp, Stefan

2002-01-01

The toxicity of PAH to willow trees (Salix alba, S. viminalis, S. viminalisx;schwerinii) was investigated. Willow cuttings were grown in PAH-saturated hydroponic solution (naphthalene NAP, phenanthrene PHEN and benzo(a)pyrene BaP). Toxicity was related to aqueous solubility and was highest for NAP...

Establishment and Early Growth of Willow at Different Levels of Weed Competition and Nitrogen Fertilization

DEFF Research Database (Denmark)

Edelfeldt, Stina; Lundkvist, Anneli; Forkman, Johannes

2016-01-01

To evaluate the effects of weed competition and nitrogen fertilization on the early growth performance of willow, cuttings of the clone Tora (Salix schwerinii x S. viminalis) were planted in buckets together with model weeds (spring barley or white mustard) sown 15, 26, and 30 days after willow...... gave higher willow biomass production in willow with weeds sown after 26 or 30 days. Type of model weed had no effect on willow performance. Weed biomass and maximum shoot height were higher in weeds planted without willows compared to the willow-weed mixtures. A high nitrogen level gave more weed...... biomass when planted without willows and in the willow-weed mixture with weeds sown after 15 days. We conclude that for the given high density of willow, competition from weeds emerging soon after willow planting had strong effect on early production. Furthermore, if there is a risk of weed infestation...

Phytotoxicity of polycyclic aromatic hydrocarbons to willow trees

Energy Technology Data Exchange (ETDEWEB)

Thygesen, R.S.; Trapp, S. [Environment and Resources DTU, Technical Univ. of Denmark, Lyngby (Denmark)

2002-07-01

The toxicity of PAH to willow trees (Salix alba, S. viminalis, S. viminalis x schwerinii) was investigated. Willow cuttings were grown in PAH-saturated hydroponic solution (naphthalene NAP, phenanthrene PHEN and benzo(a)pyrene BaP). Toxicity was related to aqueous solubility and was highest for NAP. PHEN did not show significant effects, except in one case. Exposure of trees to BaP showed no effect in two cases, but increased transpiration and growth in two others. High dosages of NAP were fatal for the trees, the lowest dosage significantly stimulated growth. Soil samples were taken from several PAH contaminated sites, among them gas works sites and a former sludge basin. The PAH contents ranged from 1.76 mg/kg to 1451 mg/kg. None of the soils was lethally toxic to the trees, and difference between growth in control soils and growth in PAH contaminated soils was not apparent. Growth and water use efficiency were positively, but not significantly correlated to the PAH content of the soils. Outdoor growth of willows and poplars on the former sludge basin in Valby was monitored, with willows growing faster than poplars (Populus trichocarpa). Phytotoxic effects could be observed at some willows at the Valby sludge basin, but it is not sure whether these effects can be contributed to PAH. (orig.)

Available data support protection of the Southwestern Willow Flycatcher under the Endangered Species Act

Science.gov (United States)

Theimer, Tad C.; Smith, Aaron D.; Mahoney, Sean M.; Ironside, Kirsten E.

2016-01-01

Zink (2015) argued there was no evidence for genetic, morphological, or ecological differentiation between the federally endangered Southwestern Willow Flycatcher (Empidonax traillii extimus) and other Willow Flycatcher subspecies. Using the same data, we show there is a step-cline in both the frequency of a mtDNA haplotype and in plumage variation roughly concordant with the currently recognized boundary between E. t. extimus and E. t adastus, the subspecies with which it shares the longest common boundary. The geographical pattern of plumage variation is also concordant with previous song analyses differentiating those 2 subspecies and identified birds in one low-latitude, high-elevation site in Arizona as the northern subspecies. We also demonstrate that the ecological niche modeling approach used by Zink yields the same result whether applied to the 2 flycatcher subspecies or to 2 unrelated species, E. t. extimus and Yellow Warbler (Setophaga petechia). As a result, any interpretation of those results as evidence for lack of ecological niche differentiation among Willow Flycatcher subspecies would also indicate no differentiation among recognized species and would therefore be an inappropriate standard for delineating subspecies. We agree that many analytical techniques now available to examine genetic, morphological, and ecological differentiation would improve our understanding of the distinctness (or lack thereof) of Willow Flycatcher subspecies, but we argue that currently available evidence supports protection of the Southwestern Willow Flycatcher under the Endangered Species Act.

Characterising willows for biomass and phytoremediation: growth, nitrogen and water use of 14 willow clones under different irrigation and fertilisation regimes

International Nuclear Information System (INIS)

Weih, Martin; Nordh, N.-E.

2002-01-01

Fourteen clones of willow (Salix spp.) were characterised in terms of growth, nitrogen and water-use efficiency under different irrigation and fertilisation treatments. Cuttings of willow clones, some commercially introduced and others new material, were pot-grown outdoors in Central Sweden under four experimental treatments in a full-factorial design. The experiment covered the period from bud-break until leaf abscission and the experimental conditions included two irrigation and two fertilisation regimes. The growth of the clones was evaluated in terms of relative growth rate and total biomass production of whole plants and shoots. Nitrogen (N) economy was studied by means of N productivity, N accumulation and N losses by leaf abscission. Water economy was analysed with respect to intrinsic water-use efficiency (foliar carbon isotope ratio; δ 13 C) and the capacity of leaves to retain water (relative water content). Significant differences between clones were found in nearly all parameters measured and the clones varied in the responses to the experimental treatments (clone x factor interaction effects). Thus, clone ranking often changed depending on the experimental treatment. The results are discussed with respect to clone selection for different willow applications such as biomass production and phytoremediation, and willow growth performance under different water and nutrient availabilities. The growth-physiological characterisation of young willows in the short term (several months) is regarded as a suitable approach for pre-selection of promising clones prior to extensive field evaluation

Status, ecology, and conservation of the southwestern willow flycatcher

Science.gov (United States)

Deborah M. Finch; Scott H. Stoleson

2000-01-01

This publication was prepared in response to a need expressed by southwestern agencies and organizations for a comprehensive assessment of the population status, history, biology, ecology, habitats, threats, and conservation of the southwestern willow flycatcher (Empidonax traillii extimus). The southwestern willow flycatcher was federally listed as...

Differential impacts of willow and mineral fertilizer on bacterial communities and biodegradation in diesel fuel oil-contaminated soil

Directory of Open Access Journals (Sweden)

Mary-Cathrine C.E. Leewis

2016-06-01

Full Text Available Despite decades of research there is limited understanding of how vegetation impacts the ability of microbial communities to process organic contaminants in soil. Using a combination of traditional and molecular assays, we examined how phytoremediation with willow and/or fertilization affected the microbial community present and active in the transformation of diesel contaminants. In a pot study, willow had a significant role in structuring the total bacterial community and resulted in significant decreases in diesel range organics (DRO. However, stable isotope probing (SIP indicated that fertilizer drove the differences seen in community structure and function. Finally, analysis of the total variance in both pot and SIP experiments indicated an interactive effect between willow and fertilizer on the bacterial communities. This study clearly demonstrates that a willow native to Alaska accelerates DRO degradation, and together with fertilizer, increased aromatic degradation by shifting microbial community structure and the identity of active naphthalene degraders.

Community outreach and education: key components of the Salix consortium's willow biomass project

International Nuclear Information System (INIS)

Volk, T.A.; Edick, S.; Brown, S.; Downing, M.

1999-01-01

This project facilitates the commercialization of willow biomass crops as a locally grown source of renewable energy. The challenge is to simultaneously optimize production and utilization technology, develop farmer interest and crop acreage, and establish stable and reliable markets. The participation of farmers and landowners, businesses, and local and regional governments in the process is essential for success. A three-phased approach elicits this participation: focused outreach and education, active involvement of potential producers of willow biomass crops, and the development of a user-friendly economic and business model that can be used by a variety of stakeholders. Barriers to commercialization have been identified, such as misconceptions about the production system and crop, assurances of a stable and reliable market for the material, and indications that the equipment and infrastructure to grow and process willow biomass crops are in place. Outreach efforts have specifically addressed these issues. As a result target audiences' responses have changed from passive observation to inquiries and suggestions for active participation. This shift represents a significant step towards the goal of making willow biomass crops a viable source of locally produced fuel. (author)

Competition favors elk over beaver in a riparian willow ecosystem

Science.gov (United States)

Baker, B.W.; Peinetti, H.R.; Coughenour, M.C.; Johnson, T.L.

2012-01-01

Beaver (Castor spp.) conservation requires an understanding of their complex interactions with competing herbivores. Simulation modeling offers a controlled environment to examine long-term dynamics in ecosystems driven by uncontrollable variables. We used a new version of the SAVANNA ecosystem model to investigate beaver (C. Canadensis) and elk (Cervus elapses) competition for willow (Salix spp.). We initialized the model with field data from Rocky Mountain National Park, Colorado, USA, to simulate a 4-ha riparian ecosystem containing beaver, elk, and willow. We found beaver persisted indefinitely when elk density was or = 30 elk km_2. The loss of tall willow preceded rapid beaver declines, thus willow condition may predict beaver population trajectory in natural environments. Beaver were able to persist with slightly higher elk densities if beaver alternated their use of foraging sites in a rest-rotation pattern rather than maintained continuous use. Thus, we found asymmetrical competition for willow strongly favored elk over beaver in a simulated montane ecosystem. Finally, we discuss application of the SAVANNA model and mechanisms of competition relative to beaver persistence as metapopulations, ecological resistance and alternative state models, and ecosystem regulation.

Above- and Belowground Development of a Fast-Growing Willow Planted in Acid-Generating Mine Technosol.

Science.gov (United States)

Guittonny-Larchevêque, M; Lortie, S

2017-11-01

Surface metal mining produces large volumes of waste rocks. If they contain sulfide minerals, these rocks can generate a flow of acidic water from the mining site, known as acid mine drainage (AMD), which increases trace metals availability for plant roots. Adequate root development is crucial to decreasing planting stress and improving phytoremediation with woody species. However, techniques to improve revegetation success rarely take into account root development. An experiment was conducted at a gold mine in Quebec, Canada, to evaluate the establishment ability over 3 yr of a fast-growing willow ( Sx64) planted in acid-generating waste rocks. The main objective was to study root development in the soil profile and trace element accumulation in leaves among substrates varying in thickness (0, 20, and 40 cm of soil) and composition (organic carbon [OC] and alkaline AMD treatment sludge). Trees directly planted in waste rocks survived well (69%) but had the lowest productivity (lowest growth in height and diameter, aerial biomass, total leaf area, and root-system size). By contrast, the treatment richer in OC showed the greatest aerial biomass and total leaf area the first year; the thicker treatment resulted in the greatest growth in height and diameter, aboveground biomass, and root-system size in both the first and third years. Willow root development was restricted to soil layers during the first year, but this restriction was overcome in the third year after planting. Willow accumulation factors in leaves were below one for all investigated trace metals except for zinc (Zn), cadmium (Cd), and strontium. For Cd and Zn, concentrations increased with time in willow foliage, decreasing the potential of this willow species use for phytostabilization, despite its ability to rapidly develop extensive root systems in the mine Technosol. Copyright © by the American Society of Agronomy, Crop Science Society of America, and Soil Science Society of America, Inc.

Improving the water use efficiency of short rotation coppice (SRC) willows

Energy Technology Data Exchange (ETDEWEB)

Stephens, W.; Bonneau, L.; Groves, S.; Armstrong, A.; Lindegard, K.

2003-07-01

On the premise that biofuels will make a significant contribution to the UK's renewable energy sources by the year 2010, willow short rotation coppicing is being studied. The high water requirement of willow is seen as a potential problem in the drier regions of the UK and increasing the water use efficiency and/or draught resistance would extend the areas where willow coppicing would be profitable. The first part of the project was to investigate the water use of a number of near-market varieties of willow and evaluate techniques for early drought tolerance screening in a breeding program and for this, field studies were conducted. This report gives some very early results from the preliminary study. Since DTI funding ceased before the one-season study of the three-year program was complete, the results should be regarded as tentative only. The next phase of the program will be funded by DEFRA and will include efforts to identify how a range of high-yielding willows respond to water stress.

Test of aerobic TCE degradation by willows (Salix viminalis) and willows inoculated with TCE-cometabolizing strains of Burkholderia cepacia.

Science.gov (United States)

Clausen, Lauge Peter Westergaard; Broholm, Mette Martina; Gosewinkel, Ulrich; Trapp, Stefan

2017-08-01

Trichloroethylene (TCE) is a widespread soil and groundwater pollutant and clean-up is often problematic and expensive. Phytoremediation may be a cost-effective solution at some sites. This study investigates TCE degradation by willows (S. viminalis) and willows inoculated with three strains of B. cepacia (301C, PR1-31 and VM1330-pTOM), using chloride formation as an indicator of dehalogenation. Willows were grown in non-sterile, hydroponic conditions for 3 weeks in chloride-free nutrient solution spiked with TCE. TCE was added weekly due to rapid loss by volatilization. Chloride and TCE in solution were measured every 2-3 days and chloride and metabolite concentrations in plants were measured at test termination. Based on transpiration, no tree toxicity of TCE exposure was observed. However, trees grown in chloride-free solution showed severely inhibited transpiration. No or very little chloride was formed during the test, and levels of chloride in TCE-exposed trees were not elevated. Chloride concentrations in chloride containing TCE-free nutrient solution doubled within 23 days, indicating active exclusion of chloride by root cell membranes. Only traces of TCE-metabolites were detected in plant tissue. We conclude that TCE is not, or to a limited extent (less than 3%), aerobically degraded by the willow trees. The three strains of B. cepacia did not enhance TCE mineralization. Future successful application of rhizo- and phytodegradation of TCE requires measures to be taken to improve the degradation rates.

SRC-willow (Salix viminalis) as a resource for flower-visiting insects

Energy Technology Data Exchange (ETDEWEB)

Reddersen, J. [National Environmental Research Institute, Ronde (Denmark). Dept. of Landscape Ecology

2001-07-01

The potential habitat value of commercial short rotation coppice (SRC)-willow plantations for flower-visiting insects was investigated. During 1998-2000, at a single typical intensive Danish farmland site, 11 Salix viminalis plantations were sampled by late April to quantify willow catkin abundance and flower sex. Mean plantation size was 1.1 ha and included one or more of clones: orm, rapp, ulv, jorr, christina and jorrun. Plot-year means of catkin abundance and of proportion of willows flowering were related to the coppicing cycle, i.e. the number of growth years since last harvest of plot ('year' 0-4). In 1998, the ground layer vegetation was sampled. Monitoring flower-visiting insects by means of line-transect counts failed due to the local scarcity of bees. At the plantation scale, flowering was discontinuous across the harvest cycle as it was totally absent in the year immediately following harvest. In successive years (1-4), individual willows flowered frequently and, occasionally, at high abundances, and catkin abundance increased with time. Within 3-4 year of harvest cycle, all plots flowered in most years with most plots exhibiting at least some flowering in any 1 year. Thus, willow catkin abundance was generally high in the total area due to: high frequency of flowering in plots, occasional high flowering abundance, plots not being harvested simultaneously and large total number of willows within plots and landscape. Similarly, flower sex ratio, and thus flower value, varied greatly between plots while variation was damped across plots. Alternative simultaneous flower resources in ground layer vegetation were few except for Dandelion. SRC willow may constitute an important resource for bees, even under the stress of the harvest cycle, and recommendations are given for improving this biodiversity aspect. (author)

Phytoremediation prospects of willow stands on contaminated sediment: a field trial

International Nuclear Information System (INIS)

Vervaeke, P.; Luyssaert, S.; Mertens, J.; Meers, E.; Tack, F.M.G.; Lust, N.

2003-01-01

A field trial indicated increased degradation of mineral oil in sediments planted with willow. - Establishing fast growing willow stands on land disposed contaminated dredged sediment can result in the revaluation of this material and opens possibilities for phytoremediation. A field trial was designed to assess the impact of planting a willow stand (Salix viminalis L. 'Orm') on the dissipation of organic contaminants (mineral oil and PAHs) in dredged sediment. In addition, the accumulation of heavy metals (Cd, Cu, Pb and Zn) in the biomass was determined. After 1.5 years, a significant decrease of 57% in the mineral oil concentration in the sediment planted with willow was observed. Degradation of mineral oil in sediment which was left fallow, was only 15%. The mineral oil degradation under willow was most pronounced (79%) in the root zone of the stand. In the sediment which was left fallow there was a significant reduction of the total PAH content by 32% compared with a 23% reduction in the planted sediment. The moderate and selective metal uptake, measured in this study, limits the prospects for phytoextraction of metals from dredged sediment

Phytoremediation prospects of willow stands on contaminated sediment: a field trial

Energy Technology Data Exchange (ETDEWEB)

Vervaeke, P.; Luyssaert, S.; Mertens, J.; Meers, E.; Tack, F.M.G.; Lust, N

2003-11-01

A field trial indicated increased degradation of mineral oil in sediments planted with willow. - Establishing fast growing willow stands on land disposed contaminated dredged sediment can result in the revaluation of this material and opens possibilities for phytoremediation. A field trial was designed to assess the impact of planting a willow stand (Salix viminalis L. 'Orm') on the dissipation of organic contaminants (mineral oil and PAHs) in dredged sediment. In addition, the accumulation of heavy metals (Cd, Cu, Pb and Zn) in the biomass was determined. After 1.5 years, a significant decrease of 57% in the mineral oil concentration in the sediment planted with willow was observed. Degradation of mineral oil in sediment which was left fallow, was only 15%. The mineral oil degradation under willow was most pronounced (79%) in the root zone of the stand. In the sediment which was left fallow there was a significant reduction of the total PAH content by 32% compared with a 23% reduction in the planted sediment. The moderate and selective metal uptake, measured in this study, limits the prospects for phytoextraction of metals from dredged sediment.

Climate impact and energy efficiency from electricity generation through anaerobic digestion or direct combustion of short rotation coppice willow

International Nuclear Information System (INIS)

Ericsson, Niclas; Nordberg, Åke; Sundberg, Cecilia; Ahlgren, Serina; Hansson, Per-Anders

2014-01-01

Highlights: • Using LCA, CHP from willow use in biogas was compared with direct combustion. • Direct combustion was ninefold more energy-efficient. • Biogas had a much greater cooling effect on global mean surface temperature. • The effects of soil carbon changes on temperature over time differed. • Biogas had long-term temperature effects, direct combustion short-term effects. - Abstract: Short rotation coppice willow is an energy crop used in Sweden to produce electricity and heat in combined heat and power plants. Recent laboratory-scale experiments have shown that SRC willow can also be used for biogas production in anaerobic digestion processes. Here, life cycle assessment is used to compare the climate impact and energy efficiency of electricity and heat generated by these measures. All energy inputs and greenhouse gas emissions, including soil organic carbon fluxes were included in the life cycle assessment. The climate impact was determined using time-dependent life cycle assessment methodology. Both systems showed a positive net energy balance, but the direct combustion system delivered ninefold more energy than the biogas system. Both systems had a cooling effect on the global mean surface temperature change. The cooling impact per hectare from the biogas system was ninefold higher due to the carbon returned to soil with the digestate. Compensating the lower energy production of the biogas system with external energy sources had a large impact on the result, effectively determining whether the biogas scenario had a net warming or cooling contribution to the global mean temperature change per kWh of electricity. In all cases, the contribution to global warming was lowered by the inclusion of willow in the energy system. The use of time-dependent climate impact methodology shows that extended use of short rotation coppice willow can contribute to counteract global warming

Coastal Energy Corporation, Willow Springs, MO

Science.gov (United States)

notice of a proposed Administrative Penalty Assessment against Coastal Energy Corporation, located at 232 Burnham Road, Willow Springs, Missouri, for alleged violations at the facility located at or near that facility.

Phytoremediation prospects of willow stands on contaminated sediment : A field trial

NARCIS (Netherlands)

Vervaeke, P; Luyssaert, S.; Mertens, J.; Meers, E.; Tack, F. M.G.; Lust, N

2003-01-01

Establishing fast growing willow stands on land disposed contaminated dredged sediment can result in the revaluation of this material and opens possibilities for phytoremediation. A field trial was designed to assess the impact of planting a willow stand (Salix viminalis L. 'Orm') on the dissipation

The potential of willow for remediation of heavy metal polluted calcareous urban soils

International Nuclear Information System (INIS)

Jensen, Julie K.; Holm, Peter E.; Nejrup, Jens; Larsen, Morten B.; Borggaard, Ole K.

2009-01-01

Growth performance and heavy metal uptake by willow (Salix viminalis) from strongly and moderately polluted calcareous soils were investigated in field and growth chamber trials to assess the suitability of willow for phytoremediation. Field uptakes were 2-10 times higher than growth chamber uptakes. Despite high concentrations of cadmium (≥80 mg/kg) and zinc (≥3000 mg/kg) in leaves of willow grown on strongly polluted soil with up to 18 mg Cd/kg, 1400 mg Cu/kg, 500 mg Pb/kg and 3300 mg Zn/kg, it is unsuited on strongly polluted soils because of poor growth. However, willow proved promising on moderately polluted soils (2.5 mg Cd/kg and 400 mg Zn/kg), where it extracted 0.13% of total Cd and 0.29% of the total Zn per year probably representing the most mobile fraction. Cu and Pb are strongly fixed in calcareous soils. - Willow is suited for remediation of moderately heavy metal polluted calcareous soils

Wastewater purification in a willow plantation. The case study at Aarike

International Nuclear Information System (INIS)

Kuusemets, V.; Mauring, T.

1996-01-01

In order to combine wastewater purification and biomass production for energy purposes, a willow plantation for wastewater treatment was established in 1995 in Aarike, Southern Estonia. Wastewater from a dwelling house (25 person equivalents, pe) is treated in a combined free-water filter system consisting of three separate basins, isolated with clay and having filter beds of gravel and sand mixture. The beds were planted with Salix viminalis. At the end of the first growing season, the purification efficiency of the newly established treatment system was 65% for BOD 7 , 43% for nitrogen and 11% for phosphorus removal. At the end of the establishment year, the above ground production of willow stems (bark and wood) and leaves was 1.3 and 0.3 t ha -1 , respectively. The figures are about three to five times higher than those recorded in previously established energy forest plantations of comparable ages in Estonia. 15 refs, 2 figs

Fertilization of SRC willow. II

DEFF Research Database (Denmark)

Sevel, L; Ingerslev, Morten; Nord-Larsen, Thomas

2014-01-01

impacts of different doses of mineral fertilizer, manure and sewage sludge in a commercially grown SRC willow stand. We examined macro nutrient and heavy metal leaching rates and calculated element balances to evaluate the environmental impact. Growth responses were reported in a former paper (Sevel et al...

A comparison of the suitability of different willow varieties to treat on-site wastewater effluent in an Irish climate.

Science.gov (United States)

Curneen, S J; Gill, L W

2014-01-15

Short rotation coppiced willow trees can be used to treat on-site wastewater effluent with the advantage that, if planted in a sealed basin and sized correctly, they produce no effluent discharge. This paper has investigated the evapotranspiration rate of four different willow varieties while also monitoring the effects of three different effluent types on each variety. The willow varieties used are all cultivars of Salix viminalis. The effluents applied were primary (septic tank) effluent, secondary treated effluent and rain water (control). The results obtained showed that the addition of effluent had a positive effect on the evapotranspiration. The willows were also found to uptake a high proportion of the nitrogen and phosphorus from the primary and secondary treated effluents added during the first year. The effect of the different effluents on the evapotranspiration rate has been used to design ten full scale on-site treatment systems which are now being monitored. Copyright © 2013 Elsevier Ltd. All rights reserved.

Uptake, metabolism, accumulation and toxicity of cyanide in willow trees

DEFF Research Database (Denmark)

Larsen, Morten; Ucisik, Ahmed Süheyl; Trapp, Stefan

2005-01-01

Chemicals taken up into plants may be accumulated so leading to toxic effects. Uptake and phytotoxicity of free cyanide was determined with the willow-tree transpiration test. Willow sets were grown in sand and irrigated with varying levels of cyanide (CN). Toxicity was determined by measuring...... transpiration. At CN concentrations below 10 mg/L, no toxic effects were observed. At 20 mg/L, transpiration was reduced to approximately 50% after 96 h. With 30, 40 and 50 mg/L, the transpiration decreased with a similar rate to cyanide in plant...... tissue was observed at 40 and 50 mg/L. The kinetics of metabolism of cyanide by roots, stems and leaves of willows was determined by the closed-bottle metabolism test. The Michaelis−Menten parameters vmax and KM (maximal metabolic velocity and half-saturation constant, respectively) were determined...

Evaluating growth effects from an imidacloprid treatment in black willow and eastern cottonwood cuttings

Science.gov (United States)

Luciano de Sene Fernandes; Ray A. Souter; Theodor D. Leininger

2015-01-01

Black willow (Salix nigra Marsh.) and eastern cottonwood (Populus deltoides Bartram ex Marsh.), two species native in the Lower Mississippi Alluvial Valley, have importance in short rotation woody crop (SRWC) systems for biomass production (Ruark 2006).

High yielding biomass genotypes of willow (Salix spp.) show differences in below ground biomass allocation

International Nuclear Information System (INIS)

Cunniff, Jennifer; Purdy, Sarah J.; Barraclough, Tim J.P.; Castle, March; Maddison, Anne L.; Jones, Laurence E.; Shield, Ian F.; Gregory, Andrew S.; Karp, Angela

2015-01-01

Willows (Salix spp.) grown as short rotation coppice (SRC) are viewed as a sustainable source of biomass with a positive greenhouse gas (GHG) balance due to their potential to fix and accumulate carbon (C) below ground. However, exploiting this potential has been limited by the paucity of data available on below ground biomass allocation and the extent to which it varies between genotypes. Furthermore, it is likely that allocation can be altered considerably by environment. To investigate the role of genotype and environment on allocation, four willow genotypes were grown at two replicated field sites in southeast England and west Wales, UK. Above and below ground biomass was intensively measured over two two-year rotations. Significant genotypic differences in biomass allocation were identified, with below ground allocation differing by up to 10% between genotypes. Importantly, the genotype with the highest below ground biomass also had the highest above ground yield. Furthermore, leaf area was found to be a good predictor of below ground biomass. Growth environment significantly impacted allocation; the willow genotypes grown in west Wales had up to 94% more biomass below ground by the end of the second rotation. A single investigation into fine roots showed the same pattern with double the volume of fine roots present. This greater below ground allocation may be attributed primarily to higher wind speeds, plus differences in humidity and soil characteristics. These results demonstrate that the capacity exists to breed plants with both high yields and high potential for C accumulation. - Highlights: • SRC willows are a source of biomass and act as carbon (C) sinks. • Biomass allocation was measured in 4 willow genotypes grown in two UK field sites. • The greatest yielding genotype had the greatest below ground biomass at both sites. • Below ground biomass allocation differed by up to 10% between genotypes and 94% between sites. • Environment e.g. wind

Ethyl lactate-EDTA composite system enhances the remediation of the cadmium-contaminated soil by Autochthonous Willow (Salix x aureo-pendula CL 'J1011') in the lower reaches of the Yangtze River

International Nuclear Information System (INIS)

Li Jiahua; Sun Yuanyuan; Yin Ying; Ji Rong; Wu Jichun; Wang Xiaorong; Guo Hongyan

2010-01-01

In order to explore a practical approach to the remediation of the cadmium (Cd)-contaminated soil in the lower reaches of the Yangtze River, we evaluated the effects of a local willow (Salix x aureo-pendula CL 'J1011') of absorbing, accumulating, and translocating Cd; and assessed the potential of chelator ethylenediaminetetraacetic acid (EDTA) in combination with ethyl lactate for enhancing the efficiency of the willow in removing Cd in two water-culture growth chamber trials and a field one. The willow showed a high tolerance to Cd in growth chamber trial 1 where the Cd concentration in the medium reached up to 25 mg L -1 medium, and the bioaccumulation factors (BAFs) of the shoots for Cd rose from 3.8 to 7.4 as the Cd concentration in the medium was elevated from 5 to 25 mg L -1 medium. In growth chamber trial 2, the average Cd removal rates in two treatments with EDTA and ethyl lactate (molar ratios of EDTA to ethyl lactate = 68/39 and 53.5/53.5, respectively) reached 0.71 mg d -1 pot -1 for the duration of Day 5-8 and 0.59 mg d -1 pot -1 for that of Day 8-11, which were 5- and 4-fold of their counterparts in the control, respectively. In the field trial, for the remediational duration of 45 days, three treatments-willow alone, willow combined with EDTA, and willow combined with EDTA and ethyl lactate-led to decreases in the Cd concentration in soil by 5%, 20%, and 29%, respectively; increases in that in the leaves by 14.6%, 56.7%, and 146.5%, respectively; and increases in that in the stems by 15.6%, 41.2%, and 87.4%, respectively, compared to their counterparts on Day 0. These results indicate that EDTA combined with ethyl lactate significantly enhanced the efficiency of willow in removing Cd from the soil. Therefore, a phytoextration system consisting of the autochthonous willow, EDTA, and ethyl lactate has high potential for the remediation of the Cd-polluted soil in the lower reaches of the Yangtze River.

Ethyl lactate-EDTA composite system enhances the remediation of the cadmium-contaminated soil by autochthonous willow (Salix x aureo-pendula CL 'J1011') in the lower reaches of the Yangtze River.

Science.gov (United States)

Li, Jiahua; Sun, Yuanyuan; Yin, Ying; Ji, Rong; Wu, Jichun; Wang, Xiaorong; Guo, Hongyan

2010-09-15

In order to explore a practical approach to the remediation of the cadmium (Cd)-contaminated soil in the lower reaches of the Yangtze River, we evaluated the effects of a local willow (Salix x aureo-pendula CL 'J1011') of absorbing, accumulating, and translocating Cd; and assessed the potential of chelator ethylenediaminetetraacetic acid (EDTA) in combination with ethyl lactate for enhancing the efficiency of the willow in removing Cd in two water-culture growth chamber trials and a field one. The willow showed a high tolerance to Cd in growth chamber trial 1 where the Cd concentration in the medium reached up to 25 mg L(-1) medium, and the bioaccumulation factors (BAFs) of the shoots for Cd rose from 3.8 to 7.4 as the Cd concentration in the medium was elevated from 5 to 25 mg L(-1) medium. In growth chamber trial 2, the average Cd removal rates in two treatments with EDTA and ethyl lactate (molar ratios of EDTA to ethyl lactate=68/39 and 53.5/53.5, respectively) reached 0.71 mg d(-1) pot(-1) for the duration of Day 5-8 and 0.59 mg d(-1) pot(-1) for that of Day 8-11, which were 5- and 4-fold of their counterparts in the control, respectively. In the field trial, for the remediational duration of 45 days, three treatments-willow alone, willow combined with EDTA, and willow combined with EDTA and ethyl lactate-led to decreases in the Cd concentration in soil by 5%, 20%, and 29%, respectively; increases in that in the leaves by 14.6%, 56.7%, and 146.5%, respectively; and increases in that in the stems by 15.6%, 41.2%, and 87.4%, respectively, compared to their counterparts on Day 0. These results indicate that EDTA combined with ethyl lactate significantly enhanced the efficiency of willow in removing Cd from the soil. Therefore, a phytoextration system consisting of the autochthonous willow, EDTA, and ethyl lactate has high potential for the remediation of the Cd-polluted soil in the lower reaches of the Yangtze River. Copyright 2010 Elsevier B.V. All rights

The potential of willow for remediation of heavy metal polluted calcareous urban soils

DEFF Research Database (Denmark)

Jensen, J K; Holm, P E; Nejrup, J

2009-01-01

Growth performance and heavy metal uptake by willow (Salix viminalis) from strongly and moderately polluted calcareous soils were investigated in field and growth chamber trials to assess the suitability of willow for phytoremediation. Field uptakes were 2-10 times higher than growth chamber...

Willow trees from heavy metals phytoextraction as energy crops

International Nuclear Information System (INIS)

Šyc, Michal; Pohořelý, Michael; Kameníková, Petra; Habart, Jan; Svoboda, Karel; Punčochář, Miroslav

2012-01-01

Phytoextraction ability of some fast growing plant species leads to the idea of connecting biomass production with soil remediation of contaminated industrial zones and regions. This biomass will contain significant amount of heavy metals and its energetic utilization has to be considered carefully to minimize negative environmental impacts. This study was focused on potential disposal methods of willow trees contaminated by heavy metals (Cd, Cu, Pb, Zn) with the emphasis on energetic utilization of biomass. Composting seems to be suitable pre-treatment method resulting in decrease of heavy metals leachability and biomass weight reduction. The possibility of willow trees application for energetic purposes was investigated and consequently incineration tests of willow trees samples in fluidized bed reactor were realized. Distribution of selected heavy metals in different ash fractions and treatment methods of produced ashes were studied as well. -- Highlights: ► Composting is an appropriate pre-treatment method for phytoextraction crops. ► Fluidized bed combustion is suitable disposal method of phytoextraction crops. ► Ashes from phytoextraction crops combustion cannot be used as fertilizers.

Erratum to: Fertilization of SRC Willow

DEFF Research Database (Denmark)

Sevel, L; Ingerslev, Morten; Nord-Larsen, Thomas

2014-01-01

impacts of different doses of mineral fertilizer, manure and sewage sludge in a commercially grown SRC willow stand. We examined macro nutrient and heavy metal leaching rates and calculated element balances to evaluate the environmental impact. Growth responses were reported in a former paper (Sevel et al...

Willow Browse Survey 2016 : Biological Summary Report

Data.gov (United States)

Department of the Interior — Browse pressure by ungulate species, primarily elk, is known to have a negative impact on the health of willow stands. On Baca and Alamosa NWR’s, it has been noticed...

Willow Browse Survey 2015 : Biological Summary Report

Data.gov (United States)

Department of the Interior — Browse pressure by ungulate species, primarily elk, is known to have a negative impact on the health of willow stands. On Baca and Alamosa NWR’s, it has been noticed...

Willow as fuel for district heating. Experiences from test combustion; Energipil som braendsel til fjernvarme - Erfaringsindsamling fra testfyringer

Energy Technology Data Exchange (ETDEWEB)

Pedersen, Joergen

2012-10-15

The project has been a study of the fuel characteristics of willow chips. The study was carried out on Trustrup-Lyngby Heating Plant and Assens District Heating Plant in the period 2011-12. Operating experiences were collected from the two plants. Furthermore, yield and crop data were collected from suppliers of willow chips to Assens District Heating Plant, and the analysis of particle size distribution of the willow chips is carried out. The collected data on yield and particle size distribution are compared with results from previous studies. The project has shown that willow chips generally are a suitable and attractive fuel in wood-fired heat and power plants. The plants are very aware of quality of willow chips and want chips with coarse structure. Furthermore, there is the wish that water content of willow chips are on par with the moisture content of wood chips, i.e. around 30-40%; woodchips are the vast majority of the chips used in the plants. Wood chips produced from fresh willow shoots with chopper will typically have a moisture content of 50-60 %. Such ''wet'' chips will of some plants be deselected during winter, where there is a requirement of safe and high boiler output. Other plants will simply mix the ''wet'' willow chips with other, drier types of chips and can use it almost all the year. If the willow shoots are harvested as branches, which subsequently are allowed to dry for a period before chipping, willow chips can be produced with a moisture content that is in line with what is typical in wood chips. Analysis of particle size distribution shows that willow chips harvested with a cutting machine usually can meet the requirements for quality classes ''fine'', ''medium'' and ''coarse''. An account of the harvested yields of willow among the growers who supplied willow chips to Assens Heating Plant, showed a relatively low yield of 5.1 tonnes dry

Comparison of willow and sunflower for uranium phytoextraction induced by citric acid

International Nuclear Information System (INIS)

Jan Mihalik; National Radiation Protection Institute, Prague; CZU, FAPPZ, Prague; Pavel Tlustos; Jirina Szakova

2010-01-01

This study deals with an efficiency of a low dose of citric acid soil application on phytoextraction of uranium. Willow (Salix spp.) and sunflower (Helianthus annus L.) were tested in this experiment with contaminated soil. The enhancing of uranium bioaccumulation was confirmed, but in contrast to previous studies, the highest quantity of uranium was accumulated in leaves. After 5 weeks of citric acid treatment, willow was more efficient in the uptake and translocation of uranium than sunflower. The transfer coefficient calculated for leaves increased from 0.033 (control) to 0.74, or 0.56 after five doses of 5 mmol of citric acid per 1 kg of soil for willow or sunflower, respectively. The uptake characterized by the total U content achieved 88 and 108 mg kg -1 in relation to the above ground parts of sunflower and willow, respectively. Even though both plants accumulated U in their above ground parts in significant rate, they employed diverse ways to achieve it. At the end of the treatment, the physiological condition of the plants enabled us to continue this method. (author)

Pathogenic and Ice-Nucleation Active (INA) Bacteria causing Dieback of Willows in Short Rotation Forestry

Energy Technology Data Exchange (ETDEWEB)

Nejad, Pajand

2005-03-01

To find out whether bacteria isolated from diseased plant parts can be the main causal agent for the dieback appearing in Salix energy forestry plantations in Sweden during the last few years, and if the joint effects of bacteria and frost injury are synergistic, extensive sampling of shoots from diseased Salix plants was performed. We performed several laboratory and greenhouse investigations and used evaluation techniques on the functions of the Ice-Nucleation Active (INA) bacteria. We carried out a comparison between spring and autumn bacterial communities isolated from within (endophytically) and surface (epiphytically) plant tissues of Salix viminalis. Seasonal variation of bacteria in willow clones with different levels of frost sensitivity and symptoms of bacterial damage was also investigated. We further focussed on possible effect of fertilisation and nutrient availability on the bacterial community in relation to plant dieback in Estonian willow plantations. The identification and detection of INA bacteria which cause damage in combination with frost to willow (Salix spp) plants in late fall, winter and spring was performed using BIOLOG MicroPlate, biochemical tests, selective INA primers and 16S rDNA analysis. To distinguish the character for differentiation between these bacteria morphologically and with respect to growing ability different culture media were used. We studied the temperature, at which ice nucleation occurred for individual bacteria, estimated the population of INA bacteria, effect of growth limiting factors, and evaluated the effect of chemical and physical agents for disruption and possible inhibition of INA among individual bacterial strains. The concentration of carbon, nitrogen and phosphorus on INA is discussed. We demonstrate that among the bacterial isolates recovered from the willow plantations, there were many that were capable of ice nucleation at temperatures between -2 and -10 deg C, many that were capable of inducing a

Predictive models of biomass for poplar and willow. Short rotation coppice in the United Kingdom

Energy Technology Data Exchange (ETDEWEB)

Brewer, A.C.; Morgan, G.W.; Poole, E.J.; Baldwin, M.E.; Tubby, I. (Biometrics, Surveys and Statistics Division, Forest Research, Farnham (United Kingdom))

2007-07-01

A series of forty-nine experimental trials on short rotation coppice (SRC) were conducted throughout the United Kingdom using a selection of varieties of poplar and willow with the aim of evaluating their performance for wood fuel production under a representative range of UK conditions. Observations on the crops and on a range of site and climatic conditions during the growth of the crops were taken over two three-year cutting cycles. These observations were used to develop a suite of empirical models for poplar and willow SRC growth and yield from which systems were constructed to provide a- priori predictions of biomass yield for any site in the UK with known characteristics (predictive yield models), and estimates of biomass yield from a standing crop (standing biomass models). The structure of the series of field trials and the consequent approach and methodology used in the construction of the suite of empirical models are described, and their use in predicting biomass yields of poplar and willow SRC is discussed. (orig.)

Puente Willow Creek en Monterrey, California

Directory of Open Access Journals (Sweden)

Editorial, Equipo

1965-09-01

Full Text Available Of the 10 awards given every year by the Prestressed Concrete Institute for the most outstanding prestressed concrete projects, two have been awarded in California this year, one of them to the Willow Creek bridge, near Monterrey. The prestressed, double T girders of this bridge were made at a workshop, a great distance from the bridge site. These are 24 m long, 1.35 m high, and are stabilized by transversal diaphragms, 20 cm in thickness. The table deck is of reinforced concrete, being 8.85 m wide and 20 cm thick. The structure is straightforward, slender, and adapts itself pleasantly to the background. It has seven spans and crosses over a secondary road, in addition to bridging the Willow stream. The supporting piles are hollow, of rectangular cross section, and over them a cross beam carries the five girders and the deck itself. The end abutments consist of vertical reinforced concrete walls, and supporting, soil filled, structures. The above information was supplied by the California Road Department.De los diez premios que anualmente concede el Prestressed Concrete Institute para las obras de hormigón pretensado más notables, dos han correspondido a California y uno de ellos al puente de Willow Creek, situado en la región de Monterrey. Las vigas de hormigón pretensado, con sección en forma de doble T, se prefabricaron en un taller situado a gran distancia del puente. Tienen 24 m de longitud y 1,35 m de canto, estando arriostradas con diafragmas transversales de 20 cm de espesor. La losa del tablero, de hormigón armado, tiene 8,85 m de anchura y 20 cm de espesor. La estructura es sencilla, esbelta y armoniza perfectamente con el paisaje que la circunda. Tiene siete tramos y salva un paso inferior secundario y el arroyo Willow. Los soportes, se apoyan sobre pilotes, algunos de gran altura; son huecos, de sección rectangular y terminan en una cruceta que sirve de sostén a las cinco vigas que soportan la losa del tablero. Los estribos

Sex- and habitat-specific responses of a high arctic willow, Salix arctica, to experimental climate change

Energy Technology Data Exchange (ETDEWEB)

Jones, M.H.; Macdonald, S.E. [Univ. of Alberta, Dept. of Renewable Resources, Edmonton, AB (Canada); Henry, G.H.R. [Univ. of British Columbia, Dept. of Geography, Vancouver, BC (Canada)

1999-10-01

Dioecious plant species and those occupying diverse habitats may present special analytical problems to researchers examining effects of climate change. Here we report the results from two complementary studies designed to determine the importance of sex and habitat on gas exchange and growth of male and female individuals of a dioecious, circumpolar willow, Salix arctica, in the Canadian High Arctic. In field studies, male and female willows from dry and wet habitats were subjected to passively enhanced summer temperature ({approx} to 1.3 deg C) using small open-top chambers over three years. Peak season gas exchange varied significantly by willow sex and habitat. Overall net assimilation was higher in the dry habitat than in the wet, and higher in females than in males. In the dry habitat, net assimilation of females was enhanced by experimental warming, but decreased in males. In the wet habitat, net assimilation of females was substantially depressed by experimental warming, while males showed an inconsistent response. Development and growth of male and female catkins were enhanced by elevated temperature more than leaf fascicles, but leaf fascicle development and growth varied more between the two habitats, particularly in males. In a controlled environment study, male and female willows from these same wet and dry habitats were grown in a 2x2 factorial experiment including 1 x or 2 x ambient [CO{sub 2}] and 5 or 12 deg. C. The sexes responded very differently to the experimental treatments, but we found no effect of original habitat. Net assimilation in males was affected by the interaction of temperature and CO{sub 2}, but in females by CO{sub 2} only. Our results demonstrate (a) significant intraspecific and intersexual differences in arctic willow physiology and growth, (b) that these differences are affected by environmental conditions expected to accompany global climate change, and (c) that sex- and habitat-specific responses should be explicitly

Machinery management data for willow harvest with a bio-baler

Energy Technology Data Exchange (ETDEWEB)

Savoie, P. [Agriculture and Agri-Food Canada, Quebec City, PQ (Canada); Hebert, P.L. [Laval Univ., Quebec City, PQ (Canada). Dept. des sols et de genie agroalimentaire; Robert, F.S. [Laval Univ., Quebec City, PQ (Canada). Sols et environnement

2010-07-01

Willow harvested in 2-to-3-year rotations has been touted as a reliable source of biomass. A newly designed harvester based on a round baler was developed in 2006. The third generation biobaler was evaluated in 2009 at 2 willow plantations in Quebec. The first site at Godmanchester was a three-year old regrowth with an estimated 52,000 stems/ha of large diameter willow. The biobaler with a flail cutter harvested three plots totalling 4,136 m{sup 2}. Total harvested biomass was 10.36 t DM in 42 bales. The harvest rate averaged 29 bale/h with an average bale size of 1.22 m wide by 1.30 m in diameter. Diesel fuel consumption averaged 0.81 L/bale. Measured losses averaged 11 per cent of the yield. The second site at Saint-Roch-del'Achigan was a two-year old growth with an estimated 49,000 stems/ha of large stem willow. The biobaler harvested seven plots totalling 15,740 m{sup 2}. Total harvest was 30.70 t DM in 148 bales. The first 14 bales were harvested with a saw blade header. All other bales were harvested with the flail cutter at a faster rate. Bale density averaged 129 kg DM/m{sup 3}. Fuel consumption averaged 0.72 L/bale. Losses averaged 20 per cent of the yield with the saw blade header.

Willow on Yellowstone's northern range: evidence for a trophic cascade?

Science.gov (United States)

Beyer, Hawthorne L; Merrill, Evelyn H; Varley, Nathan; Boyce, Mark S

2007-09-01

Reintroduction of wolves (Canis lupus) to Yellowstone National Park in 1995-1996 has been argued to promote a trophic cascade by altering elk (Cervus elaphus) density, habitat-selection patterns, and behavior that, in turn, could lead to changes within the plant communities used by elk. We sampled two species of willow (Salix boothii and S. geyeriana) on the northern winter range to determine whether (1) there was quantitative evidence of increased willow growth following wolf reintroduction, (2) browsing by elk affected willow growth, and (3) any increase in growth observed was greater than that expected by climatic and hydrological factors alone, thereby indicating a trophic cascade caused by wolves. Using stem sectioning techniques to quantify historical growth patterns we found an approximately twofold increase in stem growth-ring area following wolf reintroduction for both species of willow. This increase could not be explained by climate and hydrological factors alone; the presence of wolves on the landscape was a significant predictor of stem growth above and beyond these abiotic factors. Growth-ring area was positively correlated with the previous year's ring area and negatively correlated with the percentage of twigs browsed from the stem during the winter preceding growth, indicating that elk browse impeded stem growth. Our results are consistent with the hypothesis of a behaviorally mediated trophic cascade on Yellowstone's northern winter range following wolf reintroduction. We suggest that the community-altering effects of wolf restoration are an endorsement of ecological-process management in Yellowstone National Park.

Potential benefits of commercial willow Short Rotation Coppice (SRC) for farm-scale plant and invertebrate communities in the agri-environment

Energy Technology Data Exchange (ETDEWEB)

Rowe, Rebecca L.; Hanley, Mick E.; Goulson, Dave; Clarke, Donna J.; Doncaster, C. Patrick; Taylor, Gail [University of Southampton, Faculty of Natural and Environmental Sciences, Life Sciences Building, Southampton, S017 1BJ (United Kingdom)

2011-01-15

The cultivation of bioenergy crops (BECs) represents a significant land-use change in agri-environments, but their deployment has raised important issues globally regarding possible impacts on biodiversity. Few studies however, have systematically examined the effect of commercial scale bioenergy plantations on biodiversity in agri-ecosystems. In this study we investigate how the abundance and diversity of two key components of farmland biodiversity (ground flora and winged invertebrates) varied between mature willow Short Rotation Coppice (SRC) and two alternative land-use options (arable crops and set-aside land). Although the abundance of winged invertebrates was similar across all land-uses, taxonomic composition varied markedly. Hymenoptera and large Hemiptera (>5 mm) were more abundant in willow SRC than in arable or set-aside. Similarly although plant species richness was greater in set-aside, our data show that willow SRC supports a different plant community to the other land-uses, being dominated by competitive perennial species such as Elytrigia repens and Urtica dioica. Our results suggest that under current management practices a mixed farming system incorporating willow SRC can benefit native farm-scale biodiversity. In particular the reduced disturbance in willow SRC allows the persistence of perennial plant species, potentially providing a stable refuge and food sources for invertebrates. In addition, increased Hymenoptera abundance in willow SRC could potentially have concomitant effects on ecosystem processes, as many members of this Order are important pollinators of crop plants or otherwise fulfil an important beneficial role as predators or parasites of crop pests. (author)

Simulation modeling to understand how selective foraging by beaver can drive the structure and function of a willow community

Science.gov (United States)

Peinetti, H.R.; Baker, B.W.; Coughenour, M.B.

2009-01-01

Beaver-willow (Castor-Salix) communities are a unique and vital component of healthy wetlands throughout the Holarctic region. Beaver selectively forage willow to provide fresh food, stored winter food, and construction material. The effects of this complex foraging behavior on the structure and function of willow communities is poorly understood. Simulation modeling may help ecologists understand these complex interactions. In this study, a modified version of the SAVANNA ecosystem model was developed to better understand how beaver foraging affects the structure and function of a willow community in a simulated riparian ecosystem in Rocky Mountain National Park, Colorado (RMNP). The model represents willow in terms of plant and stem dynamics and beaver foraging in terms of the quantity and quality of stems cut to meet the energetic and life history requirements of beaver. Given a site where all stems were equally available, the model suggested a simulated beaver family of 2 adults, 2 yearlings, and 2 kits required a minimum of 4 ha of willow (containing about10 stems m-2) to persist in a steady-state condition. Beaver created a willow community where the annual net primary productivity (ANPP) was 2 times higher and plant architecture was more diverse than the willow community without beaver. Beaver foraging created a plant architecture dominated by medium size willow plants, which likely explains how beaver can increase ANPP. Long-term simulations suggested that woody biomass stabilized at similar values even though availability differed greatly at initial condition. Simulations also suggested that willow ANPP increased across a range of beaver densities until beaver became food limited. Thus, selective foraging by beaver increased productivity, decreased biomass, and increased structural heterogeneity in a simulated willow community.

Mortality of radio collared willow ptarmigan in Smoela wind-power plant

Energy Technology Data Exchange (ETDEWEB)

Pedersen, Hans Chr.; Broeseth, Henrik; Nilsen, Erlend B.; Sandercock, Brett K.; Bevanger, Kjetil

2011-07-01

Full text: In the project Pre- and post-construction studies of conflicts between birds and wind turbines in coastal Norway (BirdWind), Smoela willow ptarmigan (Lagopus lagopus variegatus) has been one of the species studied. This sub-species represent gallinaceous birds, known to be bad flyers susceptible to collide with artificial structures, e.g. power lines. However, the possible impact of a wind-power plant on survival and behaviour in a willow ptarmigan population was unknown. The objectives of the study were therefore rather wide; to study direct and indirect effects of wind turbines on willow ptarmigan behaviour, habitat selection, reproduction and survival in areas where wind-power plants are established. To collect data on habitat selection, movements, collision risks, avoidance behaviour, survival and general population dynamic parameters, willow ptarmigan were radio-tagged in 2008-2010, using traditional VHF-transmitters (Holohill) with mortality switch, necklace mount, 12 g, lasting for approximately 24 months. Due to low population density and only occasional snow cover, a method using strong lights, dipnet and car was used to catch birds. In total, 34 willow ptarmigan were caught (19 males and 15 females). All birds were caught inside the wind-power plant area (WPA). The birds were radio-tracked at irregular intervals and almost all birds, when found, was located within the WPA. All carcasses of dead birds were examined. When possible, cause of death was determined as; predation (raptor), collision, unknown, other. In total, 28 of the radio-tagged birds have died since January 2008. A Kaplan-Meier analysis of cumulative survival rates, show an exceptionally low survival (<30%). Unlike other willow ptarmigan populations most of the mortality takes place during winter, from December throughout March. Although a thorough analysis of mortality causes has yet not been carried out, a majority of the birds have probably been killed by avian predators and to

Ethyl lactate-EDTA composite system enhances the remediation of the cadmium-contaminated soil by Autochthonous Willow (Salix x aureo-pendula CL 'J1011') in the lower reaches of the Yangtze River

Energy Technology Data Exchange (ETDEWEB)

Li Jiahua [State Key Laboratory of Pollution Control and Resource Reuse, School of the Environment, Nanjing University, Nanjing 210093 (China); Sun Yuanyuan [State Key Laboratory of Pollution Control and Resource Reuse, Department of Hydrosciences, Nanjing University, Nanjing 210093 (China); Yin Ying; Ji Rong [State Key Laboratory of Pollution Control and Resource Reuse, School of the Environment, Nanjing University, Nanjing 210093 (China); Wu Jichun [State Key Laboratory of Pollution Control and Resource Reuse, Department of Hydrosciences, Nanjing University, Nanjing 210093 (China); Wang Xiaorong [State Key Laboratory of Pollution Control and Resource Reuse, School of the Environment, Nanjing University, Nanjing 210093 (China); Guo Hongyan, E-mail: hyguo@nju.edu.cn [State Key Laboratory of Pollution Control and Resource Reuse, School of the Environment, Nanjing University, Nanjing 210093 (China)

2010-09-15

In order to explore a practical approach to the remediation of the cadmium (Cd)-contaminated soil in the lower reaches of the Yangtze River, we evaluated the effects of a local willow (Salix x aureo-pendula CL 'J1011') of absorbing, accumulating, and translocating Cd; and assessed the potential of chelator ethylenediaminetetraacetic acid (EDTA) in combination with ethyl lactate for enhancing the efficiency of the willow in removing Cd in two water-culture growth chamber trials and a field one. The willow showed a high tolerance to Cd in growth chamber trial 1 where the Cd concentration in the medium reached up to 25 mg L{sup -1} medium, and the bioaccumulation factors (BAFs) of the shoots for Cd rose from 3.8 to 7.4 as the Cd concentration in the medium was elevated from 5 to 25 mg L{sup -1} medium. In growth chamber trial 2, the average Cd removal rates in two treatments with EDTA and ethyl lactate (molar ratios of EDTA to ethyl lactate = 68/39 and 53.5/53.5, respectively) reached 0.71 mg d{sup -1}pot{sup -1} for the duration of Day 5-8 and 0.59 mg d{sup -1}pot{sup -1} for that of Day 8-11, which were 5- and 4-fold of their counterparts in the control, respectively. In the field trial, for the remediational duration of 45 days, three treatments-willow alone, willow combined with EDTA, and willow combined with EDTA and ethyl lactate-led to decreases in the Cd concentration in soil by 5%, 20%, and 29%, respectively; increases in that in the leaves by 14.6%, 56.7%, and 146.5%, respectively; and increases in that in the stems by 15.6%, 41.2%, and 87.4%, respectively, compared to their counterparts on Day 0. These results indicate that EDTA combined with ethyl lactate significantly enhanced the efficiency of willow in removing Cd from the soil. Therefore, a phytoextration system consisting of the autochthonous willow, EDTA, and ethyl lactate has high potential for the remediation of the Cd-polluted soil in the lower reaches of the Yangtze River.

DESIGNING AND OPPORTUNITY FUEL WITH BIOMASS AND TIRE-DERIVED FUEL FOR COFIRING AT WILLOW ISLAND GENERATING STATION AND COFIRING SAWDUST WITH COAL AT ALBRIGHT GENERATING STATION

Energy Technology Data Exchange (ETDEWEB)

K. Payette; D. Tillman

2004-06-01

During the period July 1, 2000-March 31, 2004, Allegheny Energy Supply Co., LLC (Allegheny) conducted an extensive demonstration of woody biomass cofiring at its Willow Island and Albright Generating Stations. This demonstration, cofunded by USDOE and Allegheny, and supported by the Biomass Interest Group (BIG) of EPRI, evaluated the impacts of sawdust cofiring in both cyclone boilers and tangentially-fired pulverized coal boilers. The cofiring in the cyclone boiler--Willow Island Generating Station Unit No.2--evaluated the impacts of sawdust alone, and sawdust blended with tire-derived fuel. The biomass was blended with the coal on its way to the combustion system. The cofiring in the pulverized coal boiler--Albright Generating Station--evaluated the impact of cofiring on emissions of oxides of nitrogen (NO{sub x}) when the sawdust was injected separately into the furnace. The demonstration of woody biomass cofiring involved design, construction, and testing at each site. The results addressed impacts associated with operational issues--capacity, efficiency, and operability--as well as formation and control of airborne emissions such as NO{sub x}, sulfur dioxide (SO{sub 2}2), opacity, and mercury. The results of this extensive program are detailed in this report.

Removal of 4-chlorobenzoic acid from spiked hydroponic solution by willow trees (Salix viminalis)

DEFF Research Database (Denmark)

Deavers, K.; Macek, T.; Karlson, U.

2010-01-01

. Methods The removal of 4-CBA by willow trees was investigated with intact, septic willow trees growing in hydroponic solution and with sterile cell suspensions at concentrations of 5 mg/L and 50 mg/L 4-CBA. Nutrient solutions with different levels of ammonium and nitrate were prepared to achieve different...

Environmental applications of poplars and willows

Science.gov (United States)

J.G. Isebrands; P. Aronsson; M. Carlson; R. Ceulemans; M. Coleman; N. Dickinson; J. Dimitriou; S. Doty; E. Gardiner; K. Heinsoo; J.D. Johnson; Y.B. Koo; J. Kort; J. Kuzovkina; L. Licht; A.R. McCracken; I. McIvor; P. Mertens; K. Perttu; D. Riddell-Black; B. Robins; G. Scarascia-Mugnozza; W.R. Schroeder; John Stanturf; T.A. Volk; M. Weih

2014-01-01

Poplars and willows have been planted for environmental purposes for millennia. There are reports that poplars were planted to improve the human environment 4000 years ago in the third dynasty of Ur, for streamside stabilization 2000 years ago in what is now the south-western USA by native North Americans and for urban amenities by the early Chinese dynasties (see...

Fiber length and pulping characteristics of switchgrass, alfalfa stems, hybrid poplar and willow biomasses.

Science.gov (United States)

Ai, Jun; Tschirner, Ulrike

2010-01-01

Switchgrass (Panicum virgatum), alfalfa stems (Medicago sativa), second year growth hybrid poplar (Populus) and willow (Salix spp.) were examined to determine fiber characteristics, pulping behavior and paper properties. Alfalfa stems and switchgrass both showed length weighted average fiber length (LWW) of 0.78 mm, a very narrow fiber length distribution and high fines content. Willow and hybrid poplar have lower fines content but a very low average fiber length (0.42 and 0.48 mm LWW). In addition, the four biomass species showed distinctly different chemical compositions. Switchgrass was defibered successfully using Soda and Soda Anthraquinone (AQ) pulping and demonstrated good paper properties. Both fast-growing wood species pulped well using the Kraft process, and showed acceptable tensile strength, but low tear strength. Alfalfa stems reacted very poorly to Soda and Soda AQ pulping but responded well to Kraft and Kraft AQ. Pulps with tensile and tear strength considerably higher than those found for commercial aspen pulps were observed for alfalfa. All four biomass species examined demonstrated low pulp yield. The highest yields were obtained with poplar and switchgrass (around 43%). Considering the short fibers and low yields, all four biomass types will likely only be used in paper manufacturing if they offer considerable economic advantage over traditional pulp wood.

The potential of willow and poplar plantations as carbon sinks in Sweden

International Nuclear Information System (INIS)

Rytter, Rose-Marie

2012-01-01

A large share, estimated at 12–25%, of the annual anthropogenic greenhouse gas emissions is attributed to global deforestation. Increasing the forested areas therefore has a positive impact on carbon (C) sequestration and mitigation of high atmospheric CO 2 concentrations. Fast-growing species, such as willow and poplar, are of high interest as producers of biomass for fuel, but also as C sinks. The present study estimated the rate of C sequestration in biomass and soil in willow and poplar plantations. Calculations were based on above- and below-ground biomass production data from field experiments, including fine root turnover, litter decomposition rates, and production levels from commercial plantations. Accumulation of C in woody biomass, above and below ground, was estimated at 76.6–80.1 Mg C ha −1 and accumulation of C in the soil at 9.0–10.3 Mg C ha −1 over the first 20–22 years. The average rates of C sequestration were 3.5–4.0 Mg C ha −1 yr −1 in woody biomass, and 0.4–0.5 Mg C ha −1 yr −1 in the soil. If 400,000 ha of abandoned arable land in Sweden were planted with willow and poplar, about 1.5 Tg C would be sequestered annually in woody biomass and 0.2 Tg C in soils. This would be nearly one tenth of the annual anthropogenic emissions of C in Sweden today. These calculations show the potential of fast-growing plantations on arable land to mitigate the effect of high CO 2 concentrations over a short time span. Knowledge gaps were found during the calculation process and future research areas were suggested. -- Highlights: ► Poplars and willows as producers of biomass for fuel and as C sinks. ► Calculation of C sequestration rates in biomass and soil in willow and poplar plantations. ► Increasing forested areas has positive impact on high CO 2 levels. ► Willow and poplar plantations on arable land mitigate anthropogenic CO 2 emissions.

Wood biomass: The potential of willow

International Nuclear Information System (INIS)

White, E.H.; Abrahamson, L.P.

1991-10-01

Experiments were established in central New York State in spring, 1987, to evaluate the potential of Salix for wood biomass production using ultrashort-rotation intensive-culture techniques. Five selected willow clones and one hybrid poplar clone planted at 1 x 1 foot spacing were tested for biomass production with annual coppicing. This report presents results of this research as of December 31, 1990. (VC)

Can energy willow (Salix sp.) remediate cadmium- and nickel-contaminated fish farm sludge?

DEFF Research Database (Denmark)

Pedersen, Marianne Bruus

it meets the criteria. Phytoremediation by willow may combine accumulation of cadmium and nickel from the sludge with the production of an energy crop. The ability of eight selected willow clones to take up and tolerate cadmium and nickel was studied in pots under outdoor conditions. Fish farm sludge...

Phytoextraction of risk elements by willow and poplar trees.

Science.gov (United States)

Kacálková, Lada; Tlustoš, Pavel; Száková, Jiřina

2015-01-01

To characterize the phytoextraction efficiency of two clones of willow trees (Salix x smithiana Willd., Salix rubens) and two clones of poplar trees (Populus nigra x maximowiczii, Populus nigra Wolterson) were planted in contaminated soil (0.4-2.0 mg Cd.kg(-1), 78-313 mg Zn.kg(-1), 21.3-118 mg Cu.kg(-1)). Field experiment was carried out in Czech Republic. The study investigated their ability to accumulate heavy metals (Cd, Zn, and Cu) in harvestable plant parts. The poplars produced higher amount of biomass than willows. Both Salix clones accumulated higher amount of Cd, Zn and Cu in their biomass (maximum 6.8 mg Cd.kg(-1), 909 mg Zn.kg(-1), and 17.7 mg Cu.kg(-1)) compared to Populus clones (maximum 2.06 mg Cd.kg(-1), 463 mg Zn.kg(-1), and 11.8 mg Cu.kg(-1)). There were no significant differences between clones of individual species. BCs for Cd and Zn were greater than 1 (the highest in willow leaves). BCs values of Cu were very low. These results indicate that Salix is more suitable plant for phytoextraction of Cd and Zn than Populus. The Cu phytoextraction potential of Salix and Populus trees was not confirmed in this experiment due to low soil availability of this element.

Test of aerobic TCE degradation by willows (Salix viminalis) and willows inoculated with TCE-cometabolizing strains of Burkholderia cepacia

DEFF Research Database (Denmark)

Clausen, Lauge Peter Westergaard; Broholm, Mette Martina; Gosewinkel, Ulrich Bay

2017-01-01

. cepacia (301C, PR1-31 and VM1330-pTOM), using chloride formation as an indicator of dehalogenation. Willows were grown in non-sterile, hydroponic conditions for 3 weeks in chloride-free nutrient solution spiked with TCE. TCE was added weekly due to rapid loss by volatilization. Chloride and TCE...

Comparing predicted yield and yield stability of willow and Miscanthus across Denmark

DEFF Research Database (Denmark)

Larsen, Søren; Jaiswal, Deepak; Bentsen, Niclas Scott

2016-01-01

was 12.1 Mg DM ha−1 yr−1 for willow and 10.2 Mg DM ha−1 yr−1 for Miscanthus. Coefficent of variation as a measure for yield stability was poorest on the sandy soils of northern and western Jutland and the year-to-year variation in yield was greatest on these soils. Willow was predicted to outyield...... Miscanthus on poor, sandy soils whereas Miscanthus was higher yielding on clay-rich soils. The major driver of yield in both crops was variation in soil moisture, with radiation and precipitation exerting less influence. This is the first time these two major feedstocks for northern Europe have been compared....... The semi-mechanistic crop model BioCro was used to simulate the production of both short rotation coppice (SRC) willow and Miscanthus across Denmark. Predictions were made from high spatial resolution soil data and weather records across this area for 1990-2010. The potential average, rain-fed mean yield...

Greenhouse gas emissions from willow-based electricity: a scenario analysis for Portugal and The Netherlands

NARCIS (Netherlands)

Rebelo de Mira, R.; Kroeze, C.

2006-01-01

This study focuses on greenhouse gas emissions from power plants using willow as fuel compared to those using fossil fuels. More specifically, we quantify emissions of nitrous oxide (N2O) from soils on which willow is grown, and compare these to emissions of carbon dioxide (CO2) from fossil

Microbial expression profiles in the rhizosphere of willows depend on soil contamination

OpenAIRE

Yergeau, Etienne; Sanschagrin, Sylvie; Maynard, Christine; St-Arnaud, Marc; Greer, Charles W

2013-01-01

The goal of phytoremediation is to use plants to immobilize, extract or degrade organic and inorganic pollutants. In the case of organic contaminants, plants essentially act indirectly through the stimulation of rhizosphere microorganisms. A detailed understanding of the effect plants have on the activities of rhizosphere microorganisms could help optimize phytoremediation systems and enhance their use. In this study, willows were planted in contaminated and non-contaminated soils in a greenh...

Wind in the Willows--Theatre Activity Packet.

Science.gov (United States)

New York City Board of Education, Brooklyn, NY. Div. of Curriculum and Instruction.

Part of the New York City Board of Education's Early Stages program, and intended for elementary and secondary school teachers who wish to include a unit on theater in their classes, this guide offers suggestions for lessons and activities to accompany viewing a performance of "Wind in the Willows" at the Nederlander Theater. Part one of…

GIS-BASED location optimization of a biomass conversion plant on contaminated willow in the Campine region (Belgium)

International Nuclear Information System (INIS)

Voets, Thomas; Neven, An; Thewys, Theo; Kuppens, Tom

2013-01-01

The Campine region is diffusely contaminated with heavy metals like cadmium. Since traditional excavation techniques are too expensive, phytoremediation is preferred as a remediation technique. In a previous study, the biomass potential from phytoremediation of contaminated agricultural land in the Campine region in Belgium was assessed. Based on recently upgraded figures of willow potential from phytoremediation on agricultural land in the seven most contaminated municipalities of the Belgian Campine region, the current paper uses GIS-knowledge to investigate which of three previously identified locations is most suitable for a biomass plant, taking into account the spatial distribution of the contaminated willow supply and the total cost of willow transport. Biomass transport distance from the centroid of each contaminated agricultural parcel to each of the three potential biomass plant locations was determined following Euclidian distance calculations and distance calculations over the existing road network. A transport cost model consisting of distance fixed and distance dependent biomass transport costs was developed. Of the locations identified, the Overpelt Fabriek site results in the lowest biomass transport distance and costs. When willow allocation for each parcel occurs based on the nearest potential plant location, transport costs are on average 23% lower than when all biomass is transported to the single Overpelt Fabriek site location. Therefore, when only considering transport costs, installing a smaller plant at each of the three potential plant locations would be less expensive than when installing a single biomass plant at the Overpelt Fabriek site. -- Highlights: ► Overpelt Fabriek site most attractive for time frames considered. ► Average tortuosity factor in Campine region between 1.27 and 1.42. ► Share of willow transport costs in willow supply costs 21%. ► Optimal allocation of willow results in lower transport costs

White willow sexual regeneration capacity under estuarine conditions in times of climate change

Science.gov (United States)

Markus-Michalczyk, Heike; Hanelt, Dieter; Denstorf, Julian; Jensen, Kai

2016-10-01

Tidal wetlands provide both habitats for coastal populations and wildlife, and ecosystem services for human welfare. Building with nature regarding cost-effective coastal protection is of increasing interest. Much research has been carried out on plant reproduction capacities in mangroves and salt marshes, but less is known on this issue in tidal freshwater wetlands. Willows are being successfully used for bank stabilization in riverine habitats, however, today white willow softwood forests in tidal wetlands are highly fragmented, and restoration is required e.g. by the European Habitats Directive. Recently, tolerance to increasing salinity and tidal flooding was found for vegetative propagules of floodplain willows. However, the establishment of autochthonous sexual recruits is necessary to conserve the genetic diversity of local populations, and thus may be preferable in restoration. The germination and early seedling establishment of Salix alba (white willow) was experimentally studied under simulated estuarine conditions. The species tolerance to increasing salinity (0, 0.5, 1, 1.5, and 2) was tested in a climate chamber, and its tolerance to flooding at different tidal treatments (control, spring tide, daily tide 15 min and 2 h flooding) in the greenhouse. Germination was neither affected by increasing salinity nor by tidal flooding. Salix seedlings established up to salinity 1.5, but cotyledon performance and radicle growth was largely reduced at salinity 2. Under tidal flooding, seedling growth was similar in all treatments. However, in the treatments with daily tides seedling anchorage in the substrate took more than two weeks, and fewer seedlings reached a suitable length to approach the high water line. We assess S. alba sexual regeneration under estuarine conditions as generally possible. Further studies are needed on the effects of sedimentation-erosion processes on willow establishment in the field, especially on feedbacks between Salix survival and

Arthropods of native and exotic vegetation and their association with willow flycatchers and Wilson's warblers

Science.gov (United States)

Linda S. DeLay; Deborah M. Finch; Sandra Brantley; Richard Fagerlund; Michael D. Means; Jeffrey F. Kelly

1999-01-01

We compared abundance of migrating Willow Flycatchers and Wilson's Warblers to the abundance of arthropods in exotic and native vegetation at Bosque del Apache National Wildlife Refuge. We trapped arthropods using glue-boards in 1996 and 1997 in the same cottonwood, saltcedar, and willow habitats where we mist-netted birds during spring and fall migration. There...

Physiological and morphological responses of pine and willow saplings to post-fire salvage logging

Science.gov (United States)

Millions, E. L.; Letts, M. G.; Harvey, T.; Rood, S. B.

2015-12-01

With global warming, forest fires may be increasing in frequency, and post-fire salvage logging may become more common. The ecophysiological impacts of this practice on tree saplings remain poorly understood. In this study, we examined the physiological and morphological impacts of increased light intensity, due to post-fire salvage logging, on the conifer Pinus contorta (pine) and deciduous broadleaf Salix lucida (willow) tree and shrub species in the Crowsnest Pass region of southern Alberta. Photosynthetic gas-exchange and plant morphological measurements were taken throughout the summer of 2013 on approximately ten year-old saplings of both species. Neither species exhibited photoinhibition, but different strategies were observed to acclimate to increased light availability. Willow saplings were able to slightly elevate their light-saturated rate of net photosynthesis (Amax) when exposed to higher photosynthetic photon flux density (PPFD), thus increasing their growth rate. Willow also exhibited increased leaf inclination angles and leaf mass per unit area (LMA), to decrease light interception in the salvage-logged plot. By contrast, pine, which exhibited lower Amax and transpiration (E), but higher water-use efficiency (WUE = Amax/E) than willow, increased the rate at which electrons were moved through and away from the photosynthetic apparatus in order to avoid photoinhibition. Acclimation indices were higher in willow saplings, consistent with the hypothesis that species with short-lived foliage exhibit greater acclimation. LMA was higher in pine saplings growing in the logged plot, but whole-plant and branch-level morphological acclimation was limited and more consistent with a response to decreased competition in the logged plot, which had much lower stand density.

Environmental performance of gasified willow from different lands including land-use changes

DEFF Research Database (Denmark)

Saez de Bikuna Salinas, Koldo; Hauschild, Michael Zwicky; Pilegaard, Kim

2017-01-01

A life-cycle assessment (LCA) of a low-input, short rotation coppice (SRC) willow grown on different Danish lands was performed. Woodchips are gasified, producer gas is used for co-generation of heat and power (CHP) and the ash-char output is applied as soil amendment in the field. A hybrid model...... for abandoned farmland, as a relative C stock loss compared to natural regeneration. ILUC results show that area related GHG emissions are dominant (93% of iLUCfood and 80% of iLUCfeed), transformation being more important (82% of iLUCfood) than occupation (11%) impacts. LCA results show that CHP from willow...

The use of short rotation willows and poplars for the recycling of saline waste waters

Science.gov (United States)

Jaconette Mirck; Ronald S. Jr. Zalesny; Ioannis Dimitriou; Jill A. Zalesny; Timothy A. Volk; Warren E. Mabee

2009-01-01

The production of high-salinity waste waters by landfills and other waste sites causes environmental concerns. This waste water often contains high concentrations of sodium and chloride, which may end up in local ground and surface waters. Vegetation filter systems comprised of willows and poplars can be used for the recycling of saline waste water. These vegetation...

Conservation assessment for the autumn willow in the Black Hills National Forest, South Dakota and Wyoming

Science.gov (United States)

J. Hope Hornbeck; Carolyn Hull Sieg; Deanna J. Reyher

2003-01-01

Autumn willow, Salix serissima (Bailey) Fern., is an obligate wetland shrub that occurs in fens and bogs in the northeastern United States and eastern Canada. Disjunct populations of autumn willow occur in the Black Hills of South Dakota. Only two populations occur on Black Hills National Forest lands: a large population at McIntosh Fen and a small...

Ecophysiology of riparian cottonwood and willow before, during, and after two years of soil water removal.

Science.gov (United States)

Hultine, K R; Bush, S E; Ehleringer, J R

2010-03-01

Riparian cottonwood/willow forest assemblages are highly valued in the southwestern United States for their wildlife habitat, biodiversity, and watershed protection. Yet these forests are under considerable threat from climate change impacts on water resources and land-use activities to support human enterprise. Stream diversions, groundwater pumping, and extended drought have resulted in the decline of cottonwood/willow forests along many riparian corridors in the Southwest and, in many cases, the replacement of these forests with less desirable invasive shrubs and trees. Nevertheless, ecophysiological responses of cottonwood and willow, along with associated ecohydrological feedbacks of soil water depletion, are not well understood. Ecophysiological processes of mature Fremont cottonwood and coyote willow stands were examined over four consecutive growing seasons (2004-2007) near Salt Lake City, Utah, USA. The tree stands occurred near the inlet of a reservoir that was drained in the spring of 2005 and remained empty until mid-summer of 2006, effectively removing the primary water source for most of two growing seasons. Stem sap flux density (Js) in cottonwood was highly correlated with volumetric soil moisture (theta) in the upper 60 cm and decreased sevenfold as soil moisture dropped from 12% to 7% after the reservoir was drained. Conversely, Js in willow was marginally correlated with 0 and decreased by only 25% during the same period. Opposite patterns emerged during the following growing season: willow had a lower whole-plant conductance (kt) in June and higher leaf carbon isotope ratios (delta13C) than cottonwood in August, whereas k(t) and delta13C were otherwise similar between species. Water relations in both species recovered quickly from soil water depletion, with the exception that sapwood area to stem area (As:Ast) was significantly lower in both species after the 2007 growing season compared to 2004. Results suggest that cottonwood has a greater

UTILIZATION OF ANIMAL MEAL FOR GROWING OF WILLOW DEDICATED FOR ENERGY

Directory of Open Access Journals (Sweden)

Anna Nogalska

2016-09-01

Full Text Available The aim of the study was to evaluate the effects of increased rates of meat and bone meal (MBM to the soil on biomass yield, nitrogen (N and phosphorus (P content, and their accumulation in above ground biomass Salix viminalis, as well as the content of mineral N and available P forms in the soil. A two-year pot experiment was conducted at Warmia and Mazury University in Olsztyn (north-eastern Poland. Average biomass yield from two seasons of the studies was three higher from MBM treatments comparing to unfertilized control. Higher rates of MBM particularly in the second year showed higher yielding potential compared with mineral fertilizers. Willow biomass harvested from MBM treatments generally showed lower content of studied nutrients than willow from control treatment. It was found that in relation to the control accumulation of N in willow above ground biomass was significantly lower for 0.5% MBM treatment and significantly higher for the treatment with the highest rate (2.0%. The higher accumulation of P was found in the second year after MBM application, except treatment with the lowest MBM rate. Correlation coefficients values indicated that there is a relation between MBM rate and content of mineral N and available P in soil.

Some environmental impacts of short rotation willow coppice

International Nuclear Information System (INIS)

Slater, F.M.; Hodson, R.W.; Randrson, P.F.; Lynn, S.F.

1997-01-01

Short rotation willow coppice is a relatively new crop in upland Britain, and particularly in Environmentally Sensitive Areas the conservation and environmental effect of biomass crops needs to be evaluated. Investigations of sewage-sludge-treated plots in mid-Wales show that, because weed control was inadequate, recovery of the flora to its semi-natural precultivated state was rapid within and between experimental plots. Soil invertebrates responded to temporal stimuli before all else. Foliar-feeding invertebrates were greater in plots which had added fertilizer. Following cultivation voles were generally lost from the ploughed areas but field mice remained. Birds were studied in more extensive areas of short rotation coppice in central England and the assemblage of species was found to be similar to those found in conventional coppice but with a foreshortened successional sequence. The conservation value of short rotation willow coppice lies mainly in the abundant foliar invertebrates that provide a rich source of food for small passerine birds, particularly summer migrants. It also provides good cover for game birds - and their predators. (author)

Willow yield is highly dependent on clone and site

DEFF Research Database (Denmark)

Ugilt Larsen, Søren; Jørgensen, Uffe; Lærke, Poul Erik

2014-01-01

Use of high-yielding genotypes is one of the means to achieve high yield and profitability in willow (Salix spp.) short rotation coppice. This study investigated the performance of eight willow clones (Inger, Klara, Linnea, Resolution, Stina, Terra Nova, Tora, Tordis) on five Danish sites......, differing considerably in soil type, climatic conditions and management. Compared to the best clone, the yield was up to 36 % lower for other clones across sites and up to 51 % lower within sites. Tordis was superior to other clones with dry matter yields between 5.2 and 10.2 Mg ha−1 year−1 during the first...... 3-year harvest rotation, and it consistently ranked as the highest yielding clone on four of the five sites and not significantly lower than the highest yielding clone on the fifth site. The ranking of the other clones was more dependent on site with significant interaction between clone and site...

Synthesis of carbon nanospheres using fallen willow leaves and adsorption of Rhodamine B and heavy metals by them.

Science.gov (United States)

Qu, Jiao; Zhang, Qian; Xia, Yunsheng; Cong, Qiao; Luo, Chunqiu

2015-01-01

This paper focuses on the synthesis of carbon nanospheres (CNSs) using fallen willow leaves as a low-cost precursor. The scanning electron microscopy (SEM) image and transmission electron microscopy (TEM) image demonstrated that the structure of synthesized CNSs was spherical, with a diameter of 100 nm. The crystal structure and chemical information were characterized by Raman spectrum and energy-dispersive spectrum (EDS), respectively. BET results showed that the CNSs had a larger specific surface area of 294.32 m(2) g(-1), which makes it a potentially superior adsorbent. Rh-B and heavy metal ions such as Cu(2+), Zn(2+), and Cr(6+) were used as targets to investigate the adsorption capacity of the CNSs. The effects of adsorption parameters such as adsorption equilibrium time, dose of CNSs, adsorption kinetics, and effect factors were also studied. These findings not only established a cost-effective method of synthesizing CNSs using fallen willow leaves but also broadened the potential application range of these CNSs.

Impacts of paper sludge and manure on soil and biomass production of willow

International Nuclear Information System (INIS)

Quaye, Amos K.; Volk, Timothy A.; Hafner, Sasha; Leopold, Donald J.; Schirmer, Charles

2011-01-01

Land application of organic wastes to short rotation woody crops (SRWC) can reduce the environmental impacts associated with waste disposal and enhance the productivity of biomass production systems. Understanding the potential impacts of organic amendments however, requires the examination of changes in soil characteristics and plant productivity. This study was conducted to evaluate the effect of paper sludge and dairy manure on biomass production of shrub willow (Salix dasyclados SV1) and to determine the impacts of these amendments on soil chemical properties. Treatments included urea, dairy manure and paper sludge separately and in combination, and a control. These materials were applied in the summer of 2005 to two fields of SV1 at different stages of growth: An old field with one year old shoots on a 10 year old root system and a young field which was beginning regrowth after being coppiced at the end of its first growing season. Foliar nutrient concentrations and soil chemical properties were analyzed at the end of the second growing season after treatment application to determine plant response to the fertilization regimes and to determine the effects of fertilization on soil characteristics. Fertilization did not increase biomass production in either field. However, application of the N-poor paper sludge did not reduce yield either. In general, fertilization did not influence soil or foliar chemistry, although there were some exceptions. The lack of response observed in this study is probably related to the nutrient status of the site or losses of applied nutrients. -- Highlights: → The fertilization treatments did not have any significant effect biomass production. → Application of paper sludge did not reduce willow biomass yield in both fields. → Foliar N concentration of willow crops in this study is in the range considered for optimal growth. → The limited response of foliar nutrients to fertilization indicates that the site was not limited by

Phytoscreening and phytoextraction of heavy metals at Danish polluted sites using willow and poplar trees.

Science.gov (United States)

Algreen, Mette; Trapp, Stefan; Rein, Arno

2014-01-01

The main purpose of this study was to determine typical concentrations of heavy metals (HM) in wood from willows and poplars, in order to test the feasibility of phytoscreening and phytoextraction of HM. Samples were taken from one strongly, one moderately, and one slightly polluted site and from three reference sites. Wood from both tree species had similar background concentrations at 0.5 mg kg(-1) for cadmium (Cd), 1.6 mg kg(-1) for copper (Cu), 0.3 mg kg(-1) for nickel (Ni), and 25 mg kg(-1) for zinc (Zn). Concentrations of chromium (Cr) and lead (Pb) were below or close to detection limit. Concentrations in wood from the highly polluted site were significantly elevated, compared to references, in particular for willow. The conclusion from these results is that tree coring could be used successfully to identify strongly heavy metal-polluted soil for Cd, Cu, Ni, Zn, and that willow trees were superior to poplars, except when screening for Ni. Phytoextraction of HMs was quantified from measured concentration in wood at the most polluted site. Extraction efficiencies were best for willows and Cd, but below 0.5% over 10 years, and below 1‰ in 10 years for all other HMs.

Radiocaesium uptake and cycling in willow short rotation coppice

International Nuclear Information System (INIS)

Gommers, A.

2002-01-01

The document is an abstract of a PhD thesis. The study investigates the uptake and cycling of radiocaesium in willow short rotation coppice. Different factors influencing the soil-to-wood transfer of radiocaesium were investigated, among others the type of minerals, supply of potassium and soil composition

Spatial distribution of arsenic and heavy metals in willow roots from a contaminated floodplain soil measured by X-ray fluorescence spectroscopy

International Nuclear Information System (INIS)

Zimmer, Dana; Kruse, Jens; Baum, Christel; Borca, Camelia; Laue, Michael; Hause, Gerd; Meissner, Ralph; Leinweber, Peter

2011-01-01

Under changing redox conditions some plants create plaques at their root surface, which may affect the mobility and uptake of As and heavy metals but it is unknown to what extent this also holds true for willows in contaminated floodplain soils. Therefore, willow roots were sampled from a phytoremediation trial in the contaminated floodplain of the river Elbe (Germany), cryofixed, freeze-dried, and cross sections were mapped for the distribution of As, Ca, Cu, Fe, K, Mn, Ni, S and Zn by synchrotron based X-ray fluorescence spectroscopy. The elements Ca, Cu, Ni, S and Zn were concentrated in the aerenchymatic tissue, and not associated with Fe and Mn. Mixed Fe-Mn plaques covered the surface of the willow roots and As was accumulated in these plaques. The observed association pattern between As and Fe was explained by the different sorption/desorption properties of As(III) and As(V). The Cu and Zn intensities were not associated with the intensity of Fe in the plaque, which seems to be a willow-specific difference compared to other wetland plants. These results suggested that willows are especially suited to stabilize low-phytoextractable elements like Cu and As in their roots and rhizosphere. Thus, short rotation coppicing of willows may be a practical approach to mitigate the adverse effects of floodplain soil contamination. - Research highlights: → Elemental distributions were mapped on willow roots for the first time by synchrotron-based X-ray fluorescence. → Ca, Cu, Ni, S and Zn were enriched in the aerenchyma but As, Fe and Mn formed root plaques. → The Cu and Zn enrichments in aerenchyma but absence in plaques appeared to be willow-specific. → In the plaques were three groups of pixels which strongly differed in the As to Fe and As to Mn ratios. → This indicated different species of these redox-sensitive elements.

Spatial distribution of arsenic and heavy metals in willow roots from a contaminated floodplain soil measured by X-ray fluorescence spectroscopy

Energy Technology Data Exchange (ETDEWEB)

Zimmer, Dana, E-mail: dana.zimmer@uni-rostock.de [Soil Science, University of Rostock, Justus-von-Liebig-Weg 6, D-18051 Rostock (Germany); Kruse, Jens; Baum, Christel [Soil Science, University of Rostock, Justus-von-Liebig-Weg 6, D-18051 Rostock (Germany); Borca, Camelia [Paul Scherrer Institute, Swiss Light Source, CH-5232 Villigen PSI (Switzerland); Laue, Michael [Electron Microscopy Centre, University of Rostock, Medical Faculty, Strempelstr. 14, D-18057 Rostock (Germany); Hause, Gerd [Microscopy Unit, Biocenter of the University of Halle, Weinbergweg 22, D-06120 Halle/Saale (Germany); Meissner, Ralph [UFZ-Helmholtz Centre for Environmental Research, Department of Soil Physics, Lysimeter Station, Dorfstrasse 55, D-39615 Falkenberg (Germany); Leinweber, Peter [Soil Science, University of Rostock, Justus-von-Liebig-Weg 6, D-18051 Rostock (Germany)

2011-09-01

Under changing redox conditions some plants create plaques at their root surface, which may affect the mobility and uptake of As and heavy metals but it is unknown to what extent this also holds true for willows in contaminated floodplain soils. Therefore, willow roots were sampled from a phytoremediation trial in the contaminated floodplain of the river Elbe (Germany), cryofixed, freeze-dried, and cross sections were mapped for the distribution of As, Ca, Cu, Fe, K, Mn, Ni, S and Zn by synchrotron based X-ray fluorescence spectroscopy. The elements Ca, Cu, Ni, S and Zn were concentrated in the aerenchymatic tissue, and not associated with Fe and Mn. Mixed Fe-Mn plaques covered the surface of the willow roots and As was accumulated in these plaques. The observed association pattern between As and Fe was explained by the different sorption/desorption properties of As(III) and As(V). The Cu and Zn intensities were not associated with the intensity of Fe in the plaque, which seems to be a willow-specific difference compared to other wetland plants. These results suggested that willows are especially suited to stabilize low-phytoextractable elements like Cu and As in their roots and rhizosphere. Thus, short rotation coppicing of willows may be a practical approach to mitigate the adverse effects of floodplain soil contamination. - Research highlights: {yields} Elemental distributions were mapped on willow roots for the first time by synchrotron-based X-ray fluorescence. {yields} Ca, Cu, Ni, S and Zn were enriched in the aerenchyma but As, Fe and Mn formed root plaques. {yields} The Cu and Zn enrichments in aerenchyma but absence in plaques appeared to be willow-specific. {yields} In the plaques were three groups of pixels which strongly differed in the As to Fe and As to Mn ratios. {yields} This indicated different species of these redox-sensitive elements.

Woody plant willow in function of river water protection

Directory of Open Access Journals (Sweden)

Babincev Ljiljana M.

2011-01-01

Full Text Available Coastal area surrounding the river Ibar, in the area between cities of Kosovska Mitrovica and Leposavić in the north of Kosovo and Metohija, is occupied with seven industrial waste dumps. These dumps were all part of the exploitation and flotation refinement of raw mineral materials, metallurgic refinement of concentrates, chemical industry, industrial refinement and energetic facilities of Trepča industrial complex. The existing waste dumps, both active and inactive, are of heterogenic chemical composition. Its impact on the river water is shown by the content of heavy metals found in it. Removal of lead, cadmium and zinc would be economically unrewarding, regardless of the technology used. Wooden plant that prevails in this area is white willow. This work is focused on the removal of heavy metals (Pb, Cd and Zn from the water of the river Ibar using white willow. Roots of the willow are cultivated using the method of water cultures in an individual solution of heavy metals and river water sample. The preparation of the samples for analysis was performed by burning the herbal material and dissolving ashes in the appropriate acids. The concentrations of metals were determined by the stripping analysis. In the investigated heavy metal solutions the biomass increase is 25.6% in lead solution, 27.3% in cadmium and 30.7% in zinc solution. The increase of biomass in nutritional solution, without the heavy metals, is 32.4% and in river water sample 27.5%. The coefficient of bioaccumulation in solutions with heavy metals is 1.6% in lead solution, 1.9% in cadmium and 2.2% in zinc solution. Heavy metals accumulation is 18.74 μg of lead, 20.09 μg of cadmium and 22.89 μg of zinc. The coefficient of bioaccumulation of the water samples, that contained 44.83 μg/dm3 of lead, 29.21 μg/dm3 of cadmium and 434.00 μg/dm3 of zinc, during the period of 45 days, was 30.3% for lead, 53.4% for cadmium and 3.9% for zinc. The concentrations of accumulated metals

SELECTIVE FORAGING ON WOODY SPECIES BY THE BEAVER CASTOR FIBER, AND ITS IMPACT ON A RIPARIAN WILLOW FOREST

NARCIS (Netherlands)

NOLET, BA; HOEKSTRA, A; OTTENHEIM, MM

1994-01-01

Beavers were re-introduced in the Biesbosch, The Netherlands, a wood dominated by willows Salix spp. Conservationists expected that herbivory by beavers would enhance succession to a mixed broad-leaved forest. Willows formed the staple food of the beavers, but they removed only 1.4% of the standing

A phytotoxicity test using transpiration of willows

DEFF Research Database (Denmark)

Trapp, Stefan; Zambrano, Kim Cecilia; Kusk, Kresten Ole

2000-01-01

is expressed as % decrease after 48 and 72 h or longer compared to the initial transpiration, divided by the transpiration of control plants. More toxicity parameters are growth and water use efficiency of the plants. The sensitivity of the test was evaluated with 3,5-dichlorophenol. EC50 values between 5......A short-term acute toxicity assay for willow trees growing in contaminated solution or in polluted soil was developed and tested. The test apparatus consists of an Erlenmeyer flask with a prerooted tree cutting growing in it. Growth and reduction of transpiration are used to determine toxicity....... Transpiration is closely related to photosynthesis and growth, but is easier and faster to measure and can be measured without disturbance of the test system. Plants are grown for 24 h in uncontaminated nutrient solution before the toxicant is added to determine the initial transpiration. The loss of weight...

Phytoextraction of heavy metals by willows growing in biosolids under field conditions.

Science.gov (United States)

Laidlaw, W S; Arndt, S K; Huynh, T T; Gregory, D; Baker, A J M

2012-01-01

Biosolids produced by sewage treatment facilities can exceed guideline thresholds for contaminant elements. Phytoextraction is one technique with the potential to reduce these elements allowing reuse of the biosolids as a soil amendment. In this field trial, cuttings of seven species/cultivars of Salix(willows) were planted directly into soil and into biosolids to identify their suitability for decontaminating biosolids. Trees were irrigated and harvested each year for three consecutive years. Harvested biomass was weighed and analyzed for the contaminant elements: As, Cd, Cu, Cr, Hg, Pb, Ni, and Zn. All Salix cultivars, except S. chilensis, growing in soils produced 10 to 20 t ha(-1) of biomass, whereas most Salix cultivars growing in biosolids produced significantly less biomass (metals from biosolids, driven by superior biomass increases and not high tissue concentrations. The willows were effectual in extracting the most soluble/exchangeable metals (Cd, 0.18; Ni, 0.40; and Zn, 11.66 kg ha(-1)), whereas Cr and Cu were extracted to a lesser degree (0.02 and 0.11 kg ha(-1)). Low bioavailable elements, As, Hg, and Pb, were not detectable in any of the aboveground biomass of the willows. Copyright © by the American Society of Agronomy, Crop Science Society of America, and Soil Science Society of America, Inc.

Spatial distribution of arsenic and heavy metals in willow roots from a contaminated floodplain soil measured by X-ray fluorescence spectroscopy.

Science.gov (United States)

Zimmer, Dana; Kruse, Jens; Baum, Christel; Borca, Camelia; Laue, Michael; Hause, Gerd; Meissner, Ralph; Leinweber, Peter

2011-09-01

Under changing redox conditions some plants create plaques at their root surface, which may affect the mobility and uptake of As and heavy metals but it is unknown to what extent this also holds true for willows in contaminated floodplain soils. Therefore, willow roots were sampled from a phytoremediation trial in the contaminated floodplain of the river Elbe (Germany), cryofixed, freeze-dried, and cross sections were mapped for the distribution of As, Ca, Cu, Fe, K, Mn, Ni, S and Zn by synchrotron based X-ray fluorescence spectroscopy. The elements Ca, Cu, Ni, S and Zn were concentrated in the aerenchymatic tissue, and not associated with Fe and Mn. Mixed Fe-Mn plaques covered the surface of the willow roots and As was accumulated in these plaques. The observed association pattern between As and Fe was explained by the different sorption/desorption properties of As(III) and As(V). The Cu and Zn intensities were not associated with the intensity of Fe in the plaque, which seems to be a willow-specific difference compared to other wetland plants. These results suggested that willows are especially suited to stabilize low-phytoextractable elements like Cu and As in their roots and rhizosphere. Thus, short rotation coppicing of willows may be a practical approach to mitigate the adverse effects of floodplain soil contamination. Copyright © 2011 Elsevier B.V. All rights reserved.

Variation in copper and zinc tolerance and accumulation in 12 willow clones: implications for phytoextraction*

Science.gov (United States)

Yang, Wei-dong; Wang, Yu-yan; Zhao, Feng-liang; Ding, Zhe-li; Zhang, Xin-cheng; Zhu, Zhi-qiang; Yang, Xiao-e

2014-01-01

Willows (Salix spp.) have shown high potential for the phytoextraction of heavy metals. This study compares variations in copper (Cu) and zinc (Zn) tolerance and accumulation potential among 12 willow clones grown in a nutrient solution treated with 50 μmol/L of Cu or Zn, respectively. The results showed differences in the tolerance and accumulation of Cu and Zn with respect to different species/clones. The biomass variation among clones in response to Cu or Zn exposure ranged from the stimulation of growth to inhibition, and all of the clones tested showed higher tolerance to Cu than to Zn. The clones exhibited less variation in Cu accumulation but larger variation in Zn accumulation. Based on translocation factors, it was found that most of the Cu was retained in the roots and that Zn was more mobile than Cu for all clones. It is concluded that most willow clones are good accumulators of Zn and Cu. PMID:25183033

Cadmium concentrations in tissues of willow ptarmigan (Lagopus lagopus) and rock ptarmigan (Lagopus muta) in Nunavik, Northern Quebec

Energy Technology Data Exchange (ETDEWEB)

Rodrigue, Jean [Environment Canada, Service canadien de la faune, 1141 route de l' Eglise, Sainte-Foy, Quebec, G1V 4H5 (Canada)]. E-mail: jean.rodrigue@ec.gc.ca; Champoux, Louise [Environment Canada, Service canadien de la faune, 1141 route de l' Eglise, Sainte-Foy, Quebec, G1V 4H5 (Canada); Leclair, Daniel [Centre de recherche du Nunavik, Societe Makivik, C.P. 179, Kuujjuaq, Quebec, J0M 1C0 (Canada); Duchesne, Jean-Francois [Unite de recherche en sante publique du CHUQ, 945, avenue Wolfe, Sainte-Foy, Quebec, G1V 5B3 (Canada)

2007-06-15

Willow and rock ptarmigan were obtained from Northern Quebec. Willow ptarmigan were found to have mean cadmium concentrations of 179.7 {mu}g/g (dw) in the kidneys and 25.8 {mu}g/g (dw) in the liver; these levels were three times higher than those found in the rock ptarmigan. The cadmium levels in the ptarmigan were below the threshold above which adverse effects can be observed in birds. The difference between the two ptarmigan species in cadmium content is explained by the diet. A comparison of their diet showed that willow, which stores cadmium, is an important food resource for willow ptarmigan but not for rock ptarmigan. Because there is limited information available on the consumption of ptarmigan kidneys and liver by the Inuit, and the fact that this is a traditional way of life and provides nutritional benefits to the Inuit population, no consumption guidelines are proposed. - High levels of cadmium were found in ptarmigan in Northern Quebec. No consumption guidelines are proposed for the Inuit people.

Cadmium concentrations in tissues of willow ptarmigan (Lagopus lagopus) and rock ptarmigan (Lagopus muta) in Nunavik, Northern Quebec

International Nuclear Information System (INIS)

Rodrigue, Jean; Champoux, Louise; Leclair, Daniel; Duchesne, Jean-Francois

2007-01-01

Willow and rock ptarmigan were obtained from Northern Quebec. Willow ptarmigan were found to have mean cadmium concentrations of 179.7 μg/g (dw) in the kidneys and 25.8 μg/g (dw) in the liver; these levels were three times higher than those found in the rock ptarmigan. The cadmium levels in the ptarmigan were below the threshold above which adverse effects can be observed in birds. The difference between the two ptarmigan species in cadmium content is explained by the diet. A comparison of their diet showed that willow, which stores cadmium, is an important food resource for willow ptarmigan but not for rock ptarmigan. Because there is limited information available on the consumption of ptarmigan kidneys and liver by the Inuit, and the fact that this is a traditional way of life and provides nutritional benefits to the Inuit population, no consumption guidelines are proposed. - High levels of cadmium were found in ptarmigan in Northern Quebec. No consumption guidelines are proposed for the Inuit people

Uptake, accumulation and metabolic response of ferricyanide in weeping willows.

Science.gov (United States)

Yu, Xiao-Zhang; Gu, Ji-Dong

2009-01-01

The remediation potential and metabolic responses of plants to ferricyanide were investigated using pre-rooted weeping willows (Salix babylonica L.) grown hydroponically in growth chambers and treated with potassium ferricyanide. Positive responses were observed for the plants exposed to cyanide recovered in plant biomass was constant in all treatments, indicating that transport is a major limiting step for the uptake of ferricyanide by plants. The majority of the ferricyanide taken up from the growth media was possibly assimilated during transport through plants. The velocity of the removal processes can be described by Michaelis-Menten kinetics, and the half-saturation constant (K(M)) and the maximum removal capacity (v(max)) were estimated to be 228.1 mg CN L(-1) and 36.43 mg CN kg(-1) d(-1), respectively, using non-linear regression methods. These results suggest that weeping willows can take up, transport and assimilate ferricyanide; and phytoremediation is an option for cleaning up the environmental sites contaminated with cyanide complexes.

Willow and poplar for bioenergy on former cropland

DEFF Research Database (Denmark)

Georgiadis, Petros

and water demands of the trees. The water requirements of SRWCs are generally high, and high evapotranspiration rates in both SRC willow and SRF poplar decreased deep percolation, which along with low N concentrations led to low N leaching. Excessive N leaching was only observed when SRC was fertilized......Climate change is one of the 21st century’s greatest challenges and calls for immediate action through the implementation of mitigation strategies. A shift from fossil fuel to renewable energy is a key factor for reducing greenhouse gas emissions to the atmosphere, with bioenergy being...... the predominant sector of renewables in the current European and global energy markets. Dedicated energy crops, such as short rotation woody crops (SRWC), are promising bioenergy feedstock in southern Scandinavia due to their high yields. Such cropping systems have high demands for land, water, and nutrients...

With willows and poplars against the heavy metals

International Nuclear Information System (INIS)

Jaros, M.

2002-01-01

Special kinds of trees take out cadmium, lead and zinc from the soil, helping its rehabilitation in contaminated regions. A new method for soil rehabilitation (phytoremediation) based on plants is described. Special willows and poplars have the capability to extract as a sponge heavy metals from the soils and store them in their leaves. For example, they can uptake 700 times the amount of cadmium than the normal plants do. (nevyjel)

"The Wind in the Willows" and the Style of Romance

Science.gov (United States)

Gill, R. B.

2012-01-01

The style of Kenneth Grahame's "The Wind in the Willows" arises from an alternative vision and choice of values characteristic of romance. Romance seeks fulfillment beyond the consequences of everyday relationships and the constrictions of ordinary life. Causal relationships give way to lists of independent items, unmotivated outcomes, and…

The Willow Microbiome is Influenced by Soil Petroleum-Hydrocarbon Concentration with Plant Compartment-Specific Effects

Directory of Open Access Journals (Sweden)

Stacie Tardif

2016-09-01

Full Text Available The interaction between plants and microorganisms, which is the driving force behind the decontamination of petroleum hydrocarbon (PHC contamination in phytoremediation technology, is poorly understood. Here, we aimed at characterizing the variations between plant compartments in the microbiome of two willow cultivars growing in contaminated soils. A field experiment was set-up at a former petrochemical plant in Canada and, after two growing seasons, bulk soil, rhizosphere soil, roots and stems samples of two willow cultivars (Salix purpurea cv. FishCreek and Salix miyabeana cv. SX67 growing at three PHC contamination concentrations were taken. DNA was extracted and bacterial 16S rRNA gene and fungal internal transcribed spacer (ITS regions were amplified and sequenced using an Ion Torrent Personal Genome Machine. Following multivariate statistical analyses, the level of PHC-contamination appeared as the primary factor influencing the willow microbiome with compartment-specific effects, with significant differences between the responses of bacterial and fungal communities. Increasing PHC contamination levels resulted in shifts in the microbiome composition, favoring putative hydrocarbon degraders and microorganisms previously reported as associated with plant health. These shifts were less drastic in the rhizosphere, root and stem tissues as compared to bulk soil, probably because the willows provided a more controlled environment and thus protected microbial communities against increasing contamination levels. Insights from this study will help to devise optimal plant microbiomes for increasing the efficiency of phytoremediation technology.

Energy balance and evaporation of a short-rotation willow forest. Variation with season and stand development

Energy Technology Data Exchange (ETDEWEB)

Iritz, Z.

1996-10-01

Energy balance and evaporation of a short-rotation willow (Salix viminalis L.) forest was studied in relation to season and stand development. The developmental stage of the forest stand considerably influenced how the energy, received as net radiation, was partitioned between the connective fluxes and the storage components. The main part of the available energy was utilised for evaporation during most of the season. Only at the beginning of the season did the willow forest supply heat to the atmosphere. Later in the season, energy was taken from air and utilised for evaporation, which resulted in negative sensible heat fluxes. Soil heat storage was also a significant term in the energy balance and also strongly depended on canopy development. Changes in energy partitioning relative to leaf area indices indicated the existence of a threshold value for leaf area index of the developing canopy. The analysis suggested that the canopy of the willow forest could be considered as closed at a leaf area index of 2. It was further found that evaporation from well-irrigated willow forest occurred also during night-time, particularly in windy and dry weather conditions. The sources of nocturnal evaporation were both the canopy, i.e. indicating non-closed stomata, and the soil surface. Partitioning of the total evaporation into components was investigated using a physically-based model with a two-layer aboveground representation and a two-layer soil module. The model estimates evaporation with respect to developmental stage of the willow stand and also takes into account the interaction between the fluxes from the canopy and the soil surface. Good performance of the model indicated that, after further testing in drier conditions, it could be used as a tool for analysing the prerequisites for energy-forest establishment, and practical management of energy forest stands. 37 refs, 9 figs

Genetic variation in the endangered Southwestern Willow Flycatcher

Science.gov (United States)

Busch, Joseph; Miller, Mark P.; Paxton, E.H.; Sogge, M.K.; Keim, Paul

2000-01-01

The Southwestern Willow Flycatcher (Empidonax traillii extimus) is an endangered Neotropical migrant that breeds in isolated remnants of dense riparian habitat in the southwestern United States. We estimated genetic variation at 20 breeding sites of the Southwestern Willow Flycatcher (290 individuals) using 38 amplified fragment length polymorphisms (AFLPs). Our results suggest that considerable genetic diversity exists within the subspecies and within local breeding sites. Statistical analyses of genetic variation revealed only slight, although significant, differentiation among breeding sites (Mantel's r = 0.0705, P UPGMA cluster analysis of the AFLP markers indicates that extensive gene flow has occurred among breeding sites. No one site stood out as being genetically unique or isolated. Therefore, the small level of genetic structure that we detected may not be biologically significant. Ongoing field studies are consistent with this conclusion. Of the banded birds that were resighted or recaptured in Arizona during the 1996 to 1998 breeding seasons, one-third moved between breeding sites and two-thirds were philopatric. Low differentiation may be the result of historically high rangewide diversity followed by recent geographic isolation of breeding sites, although observational data indicate that gene flow is a current phenomenon. Our data suggest that breeding groups of E. t. extimus act as a metapopulation.

Differential effects of glyphosate and aminomethylphosphonic acid (AMPA) on photosynthesis and chlorophyll metabolism in willow plants.

Science.gov (United States)

Gomes, Marcelo Pedrosa; Le Manac'h, Sarah Gingras; Maccario, Sophie; Labrecque, Michel; Lucotte, Marc; Juneau, Philippe

2016-06-01

We used a willow species (Salix miyabeana cultivar SX64) to examine the differential secondary-effects of glyphosate and aminomethylphosphonic acid (AMPA), the principal glyphosate by-product, on chlorophyll metabolism and photosynthesis. Willow plants were treated with different concentrations of glyphosate (equivalent to 0, 1.4, 2.1 and 2.8kgha(-1)) and AMPA (equivalent to 0, 0.28, 1.4 and 2.8kgha(-1)) and evaluations of pigment contents, chlorophyll fluorescence, and oxidative stress markers (hydrogen peroxide content and antioxidant enzyme activities) in leaves were performed after 12h of exposure. We observed that AMPA and glyphosate trigger different mechanisms leading to decreases in chlorophyll content and photosynthesis rates in willow plants. Both chemicals induced ROS accumulation in willow leaves although only glyphosate-induced oxidative damage through lipid peroxidation. By disturbing chlorophyll biosynthesis, AMPA induced decreases in chlorophyll contents, with consequent effects on photosynthesis. With glyphosate, ROS increases were higher than the ROS-sensitive threshold, provoking chlorophyll degradation (as seen by pheophytin accumulation) and invariable decreases in photosynthesis. Peroxide accumulation in both AMPA and glyphosate-treated plants was due to the inhibition of antioxidant enzyme activities. The different effects of glyphosate on chlorophyll contents and photosynthesis as described in the literature may be due to various glyphosate:AMPA ratios in those plants. Copyright © 2015 Elsevier Inc. All rights reserved.

A Natural History Summary and Survey Protocol for the Southwestern Willow Flycatcher

Science.gov (United States)

Sogge, Mark K.; ,; Ahlers, Darrell; ,; Sferra, Susan J.; ,

2010-01-01

The Southwestern Willow Flycatcher (Empidonax traillii extimus) has been the subject of substantial research, monitoring, and management activity since it was listed as an endangered species in 1995. When proposed for listing in 1993, relatively little was known about the flycatcher's natural history, and there were only 30 known breeding sites supporting an estimated 111 territories rangewide (Sogge and others, 2003a). Since that time, thousands of presence/absences surveys have been conducted throughout the historical range of the flycatcher, and many studies of its natural history and ecology have been completed. As a result, the ecology of the flycatcher is much better understood than it was just over a decade ago. In addition, we have learned that the current status of the flycatcher is better than originally thought: as of 2007, the population was estimated at approximately 1,300 territories distributed among approximately 280 breeding sites (Durst and others, 2008a). Concern about the Southwestern Willow Flycatcher on a rangewide scale was brought to focus by Unitt (1987), who described declines in flycatcher abundance and distribution throughout the Southwest. E. t. extimus populations declined during the 20th century, primarily because of habitat loss and modification from activities, such as dam construction and operation, groundwater pumping, water diversions, and flood control. In 1991, the U.S. Fish and Wildlife Service (USFWS) designated the Southwestern Willow Flycatcher as a candidate category 1 species (U.S. Fish and Wildlife Service, 1991). In July 1993, the USFWS proposed to list E. t. extimus as an endangered species and to designate critical habitat under the Act (U.S. Fish and Wildlife Service, 1993). A final rule listing E. t. extimus as endangered was published in February 1995 (U.S. Fish and Wildlife Service, 1995); critical habitat was designated in 1997 (U.S. Fish and Wildlife Service, 1997). The USFWS Service released a Recovery Plan for

Evaluating the impact of three incentive programs on the economics of cofiring willow biomass with coal in New York State

International Nuclear Information System (INIS)

Tharakan, P.J.; Volk, T.A.; Lindsey, C.A.; Abrahamson, L.P.; White, E.H.

2005-01-01

Plantations of fast-growing willow shrubs are being promoted as a source quality biomass feedstock for bioenergy and bioproducts in New York State (NY). In the near-term, cofiring of the feedstock--in combination with other woody biomass--with coal in existing utility power boilers is considered to be the most promising conversion method for energy generation. Despite the clear technological viability and associated environmental benefits, cofiring of willow has not been widely adopted. The relatively high production cost of the willow feedstock, which is over twice that of coal, is the primary reason for this lack of interest. Taxes that account for some of the social costs of using coal and/or incentives that appropriate value for some of the social benefits of using willow are essential for eliminating most or the entire current price differential. This paper presents an integrated analysis of the economics of power generation from cofiring willow biomass feedstock with coal, from the perspective of the grower, aggregator and the power plant. Emphasis is placed on analyzing the relative impact of a green premium price, a closed-loop biomass tax credit, and payments to growers under the proposed Conservation Reserve Program (CRP) harvesting exemption policy. The CRP payments reduced the delivered cost of willow by 36-35%, to $1.90 GJ -1 and $1.70 GJ -1 , under current and increased yield conditions, respectively. These prices are still high, relative to coal. Other incentives are required to ensure commercial viability. The required levels of green premium price (0.4-1.0 cents kWh -1 ) and biomass tax credit (0.75-2.4 cents kWh -1 ) vary depending on whether the incentives were being applied by themselves or in combination, and whether current yield or potential increased yields were being considered. In the near term, cofiring willow biomass and coal can be an economically viable option for power generation in NY if the expected overall beneficial effects

Initial spacing of poplars and willows grown as arable coppice

Energy Technology Data Exchange (ETDEWEB)

Armstrong, A.; Johns, C.

1997-11-01

Two clones of poplar and two clones of willow were grown at two sites, on a three year cutting cycle, at six different square spacings, between 0.8 metres and 1.5 metres. The two willow clones 'Bowles hybrid' and 'Dasyclados' were planted at both sites. The poplar clones Populus interamericana 'Beaupre' and Populus trichocarpa 'Columbia River'' were planted at Wishanger in Hampshire. The poplar clones Populus interamericana 'Boelare' and Populus trichocarpa 'Trichobel' were planted at Downham Market in Norfolk. The highest yield of 17.55 oven dry tonnes per hectare (odt/ha/annum) was obtained from 'Bowles hybrid', at the closest spacing, grown on a water meadow adjacent to the River Wey at Wishanger. The highest yield for all clones at both sites was achieved at the closest spacing (in this first rotation). There was a significant linear effect. One of the most interesting observations was that when comparing the gradient of the linear relationship, within species, the gradient was steeper for the higher yielding clone. This was particularly so for the willows. This would suggest that higher yielding clones are more tolerant of crowding, or, that upright Salix viminalis make better use of close space than the more spreading Salix dasyclados. The new Salix x Salix schwerinnii hybrids should therefore also be responsive to closer spacing. The same effect was observed for the poplars at Wishanger only, but the difference was not as dramatic. There was a suggestion from the highest yielding poplar plots that optimum yield may still be obtained at the currently recommended spacing of 1.0 metre x 1.0 metre. (author)

Production of Probiotic Drink Using Pussy willow and Echium amoenum Extracts

Directory of Open Access Journals (Sweden)

Mahbobeh Eksiri

2017-06-01

Full Text Available Background and Objective: Nowadays, due to the lack of lactose and cholesterol, demand for consumption of non-dairy probiotic products is increasing. Probiotic drinks mixed with medicinal plant have great beneficial effect on human health. The main problems of non-dairy probiotic drinks are lack of nutrients for the growth of probiotics and bad taste of the product. The aim of this study was to produce a probiotic medicinal plant drink with favorable physicochemical, viability and sensory properties.Material and Methods: Probiotic drink prepared by Pussy willow and Echium amoenum extract (0.5 % w v-1, for each extract or together, Lactobacillus casei and Lactobacillus rhamnosus (108 CFU ml-1, individually and their combination. Glucose and whey powder (0.2% were used as a source of nutrition for the probiotics, and apple juice (20 and 30% was added to improve the taste of drink. The level of glucose was adjusted to reach the brix of 13 g100 g-1. Ascorbic acid (0.05% was used to improve micro-aerophilic conditions. The pH, acidity, glucose and viability of probiotic bacteria as well as the sensory properties of the prepared drink were investigated during 28 days at 4°C.Results and Conclusion: Based on the results, the treatment containing L. casei, Pussy willow, Echium amoenum and 30% apple juice due to the highest probiotic viability and the treatment containing Lactobacillus rhamnosus, Pussy willow, Echium amoenum and 30% apple juice because of higher total acceptance score, proper pH and acidity values were selected as the best treatments.Conflict of interest: The authors declare no conflict of interest.

The Study of Interactions between Active Compounds of Coffee and Willow (Salix sp. Bark Water Extract

Directory of Open Access Journals (Sweden)

Agata Durak

2014-01-01

Full Text Available Coffee and willow are known as valuable sources of biologically active phytochemicals such as chlorogenic acid, caffeine, and salicin. The aim of the study was to determine the interactions between the active compounds contained in water extracts from coffee and bark of willow (Salix purpurea and Salix myrsinifolia. Raw materials and their mixtures were characterized by multidirectional antioxidant activities; however, bioactive constituents interacted with each other. Synergism was observed for ability of inhibition of lipid peroxidation and reducing power, whereas compounds able to scavenge ABTS radical cation acted antagonistically. Additionally, phytochemicals from willow bark possessed hydrophilic character and thermostability which justifies their potential use as an ingredient in coffee beverages. Proposed mixtures may be used in the prophylaxis or treatment of some civilization diseases linked with oxidative stress. Most importantly, strong synergism observed for phytochemicals able to prevent lipids against oxidation may suggest protective effect for cell membrane phospholipids. Obtained results indicate that extracts from bark tested Salix genotypes as an ingredient in coffee beverages can provide health promoting benefits to the consumers; however, this issue requires further study.

Uptake, removal, accumulation, and phytotoxicity of 4-chlorophenol in willow trees

DEFF Research Database (Denmark)

Ucisik, Ahmed Süheyl; Trapp, Stefan

2008-01-01

of implementing phytoremediation as a treatment method for 4-CP contamination was investigated. Willows were exposed to 4-CP levels ≤79.9 mg/L in hydroponic solution. The transpiration of the trees was used to determine toxic effects. Almost no inhibition of transpiration was detected at concentrations ≥15 mg...

Microbial expression profiles in the rhizosphere of willows depend on soil contamination

Science.gov (United States)

Yergeau, Etienne; Sanschagrin, Sylvie; Maynard, Christine; St-Arnaud, Marc; Greer, Charles W

2014-01-01

The goal of phytoremediation is to use plants to immobilize, extract or degrade organic and inorganic pollutants. In the case of organic contaminants, plants essentially act indirectly through the stimulation of rhizosphere microorganisms. A detailed understanding of the effect plants have on the activities of rhizosphere microorganisms could help optimize phytoremediation systems and enhance their use. In this study, willows were planted in contaminated and non-contaminated soils in a greenhouse, and the active microbial communities and the expression of functional genes in the rhizosphere and bulk soil were compared. Ion Torrent sequencing of 16S rRNA and Illumina sequencing of mRNA were performed. Genes related to carbon and amino-acid uptake and utilization were upregulated in the willow rhizosphere, providing indirect evidence of the compositional content of the root exudates. Related to this increased nutrient input, several microbial taxa showed a significant increase in activity in the rhizosphere. The extent of the rhizosphere stimulation varied markedly with soil contamination levels. The combined selective pressure of contaminants and rhizosphere resulted in higher expression of genes related to competition (antibiotic resistance and biofilm formation) in the contaminated rhizosphere. Genes related to hydrocarbon degradation were generally more expressed in contaminated soils, but the exact complement of genes induced was different for bulk and rhizosphere soils. Together, these results provide an unprecedented view of microbial gene expression in the plant rhizosphere during phytoremediation. PMID:24067257

Phytotoxicity of Sodium Fluoride and Uptake of Fluoride in Willow Trees

DEFF Research Database (Denmark)

Clausen, Lauge Peter Westergaard; Gosewinkel Karlson, Ulrich; Trapp, Stefan

2015-01-01

The willow tree (Salix viminalis) toxicity test and a cress seed germination test (Lepidium sativum) were used to determine uptake and phytotoxicity of NaF. Concentrations in hydroponic solutions were 0-1000 mg F/L and 0-400 mg F/L in the preliminary and definitive test. A third test was done...

Conversion from cropland to short rotation coppice willow and poplar: Accumulation of soil organic carbon

Science.gov (United States)

Georgiadis, Petros; Stupak, Inge; Vesterdal, Lars; Raulund-Rasmussen, Karsten

2015-04-01

Increased demand for bioenergy has intensified the production of Short Rotation Coppice (SRC) willow and poplar in temperate zones. We used a combined chronosequence and paired plot approach to study the potential of SRC willow and poplar stands to increase the soil carbon stock compared to stocks of the previous arable land-use. The study focused on well-drained soils. We sampled soil from 30 SRC stands in Denmark and southern Sweden including soils from their adjacent arable fields. The 18 willow and 12 poplar stands formed a chronosequence ranging between 4 and 29 years after conversion. The soil was sampled both with soil cores taken by fixed depths of 0-5, 5-10, 10-15, 15-25, and 25-40 cm and by genetic horizons from soil pits to 1m depth. The aim of the study was to estimate the difference and the ratio between soil carbon contents of the SRC and annual crop land and analyze the results as a chronosequence to examine the effect of age after conversion on the difference. Covariates such as soil type, fertilization type and harvest frequency were also taken into account. Preliminary results suggest an overall increase in carbon stocks over time with average accumulation rates ranging from 0.25 to 0.4 Mg ha-1 yr-1 in willow and poplar stands. Poplar stands had higher rates of C gain, probably due to less frequent harvesting. The differences in carbon between the SRC and the paired cropland were initially negative but changed to positive over time, implying loss of carbon after conversion and a later gain in soil carbon with stand age. Pairwise differences ranged from -25 Mg C ha-1 to 37 Mg C ha-1 for the top 40 cm. The carbon stock ratio of the SRC stand to the arable land was estimated to minimize the effect of site-related factors. The results of this analysis suggested that the ratio increased significantly with age after conversion for the top 10 cm of the soil, both for poplar and willow. A slight increase with age was also noticed at the deeper depths, but

Translocation of Cd and Mn from Bark to Leaves in Willows on Contaminated Sediments: Delayed Budburst Is Related to High Mn Concentrations

Directory of Open Access Journals (Sweden)

Bart Vandecasteele

2015-04-01

Full Text Available Changes in the hydrology of sediments in tidal marshes or landfills may affect the uptake of metals in the vegetation. Leaf and stem samples of Salix cinerea (grey sallow were collected during four consecutive growing seasons at six contaminated plots on a polluted dredged sediment landfill and one plot on an uncontaminated reference site. The first three contaminated plots were already emerged in the first half of the first growing season, while the other three were submerged in the first year, but became increasingly dry over the study period. Foliar and stem cutting concentrations for Cd, Zn and Mn increased on the latter three plots over the four years. Willow bark contained high concentrations of Cd, Zn and Mn. In two consecutive greenhouse experiments with willow cuttings from different origins (uncontaminated and contaminated sites and grown under different soil conditions (uncontaminated and contaminated, we observed an important translocation of Mn from bark to shoots. In a third experiment with willow cuttings collected on soils with a range of heavy metal concentrations and, thus, with a broad range of Cd (4–67 mg/kg dry matter, Zn (247–660 mg/kg dry matter and Mn (38–524 mg/kg dry matter concentrations in the bark, high Mn concentrations in the bark were found to affect the budburst of willow cuttings, while no association of delayed budburst with Cd and Zn concentrations in the bark was found. We conclude that wood and, especially, bark are not a sink for metals in living willows. The high Mn concentrations in the bark directly or indirectly caused delayed or restricted budburst of the willow cuttings.

The level of invasion of the willow-poplar floodplain forests of Danube lowland

International Nuclear Information System (INIS)

Botkova, K.; Petrasova, K.

2015-01-01

Invasions of neophyte plant species are considered as one of the major threats to the diversity of natural ecosystems including floodplain forests. The aims of our study were to find out if there is a significant increase in the number and cover of neophyte species in the willow-poplar floodplain forests of Danube lowland over time. The level of invasion of the willow-poplar floodplain forests was evaluated from 1950 to the present time using Kruskal-Wallis non-parametric ANOVA. According to the analysis results, along the time gradient there is a significant increase in the number and cover of neophytes among analysed periods. This result is not caused by increasing biodiversity, because the number of native species significantly decreased. Therefor it is necessary to look for reasons of this situation in deteriorating condition of floodplain biotopes. (authors)

Clonal variation in survival and growth of hybrid poplar and willow in an in situ trial on soils heavily contaminated with petroleum hydrocarbons

Science.gov (United States)

Ronald S., Jr. Zalesny; Edmund O. Bauer; Richard B. Hall; Jill A. Zalesny; Joshua Kunzman; Chris J. Rog; Don E. Riemenschneider

2005-01-01

Species and hybrids between species belonging to the genera Populus (poplar) and Salix (willow) have been used successfully for phytoremediation of contaminated soils. Our objectives were to: 1) evaluate the potential for establishing genotypes of poplar and willow on soils heavily contaminated with petroleum hydrocarbons and 2)...

Vegetative reproduction capacities of floodplain willows--cutting response to competition and biomass loss.

Science.gov (United States)

Radtke, A; Mosner, E; Leyer, I

2012-03-01

While several studies on regeneration in Salicaceae have focused on seedling recruitment, little is known about factors controlling their vegetative reproduction. In two greenhouse experiments, we studied the response of floodplain willows (Salix fragilis, S. viminalis, S. triandra) to competition with Poa trivialis, and to shoot and root removal when planted as vegetative cuttings. In the first experiment, growth performance variables were analysed in relation to full competition, shoot competition, root competition and control, taking into account two different water levels. After 9 weeks, shoots were removed and the resprouting capacity of the bare cuttings was recorded. In the second experiment, the cutting performance of the three floodplain and an additional two fen willow species (S. cinerea, S. aurita) was compared when grown in three different soil compositions and with two different water levels. After 9 weeks, shoot and root biomass was removed and the bare cuttings were replanted to test their ability to resprout. Cutting performance and secondary resprouting were negatively affected by full and shoot competition while root competition had no or weak effects. The floodplain species performed better than the fen species in all soil types and water levels. Secondary resprouting capacity was also higher in the floodplain species, which showed an additional strong positive response to the previous waterlogging treatment. The results contribute to understanding of the vegetative regeneration ecology of floodplain willows, and suggest that the use of vegetative plantings in restoration plantings could be an effective strategy for recovering floodplain forests. © 2011 German Botanical Society and The Royal Botanical Society of the Netherlands.

Water relations and gas exchange in poplar and willow under water stress and elevated atmospheric CO2.

Science.gov (United States)

Johnson, Jon D; Tognetti, Roberto; Paris, Piero

2002-05-01

Predictions of shifts in rainfall patterns as atmospheric [CO2] increases could impact the growth of fast growing trees such as Populus spp. and Salix spp. and the interaction between elevated CO2 and water stress in these species is unknown. The objectives of this study were to characterize the responses to elevated CO2 and water stress in these two species, and to determine if elevated CO2 mitigated drought stress effects. Gas exchange, water potential components, whole plant transpiration and growth response to soil drying and recovery were assessed in hybrid poplar (clone 53-246) and willow (Salix sagitta) rooted cuttings growing in either ambient (350 &mgr;mol mol-1) or elevated (700 &mgr;mol mol-1) atmospheric CO2 concentration ([CO2]). Predawn water potential decreased with increasing water stress while midday water potentials remained unchanged (isohydric response). Turgor potentials at both predawn and midday increased in elevated [CO2], indicative of osmotic adjustment. Gas exchange was reduced by water stress while elevated [CO2] increased photosynthetic rates, reduced leaf conductance and nearly doubled instantaneous transpiration efficiency in both species. Dark respiration decreased in elevated [CO2] and water stress reduced Rd in the trees growing in ambient [CO2]. Willow had 56% lower whole plant hydraulic conductivity than poplar, and showed a 14% increase in elevated [CO2] while poplar was unresponsive. The physiological responses exhibited by poplar and willow to elevated [CO2] and water stress, singly, suggest that these species respond like other tree species. The interaction of [CO2] and water stress suggests that elevated [CO2] did mitigate the effects of water stress in willow, but not in poplar.

COMPACTION STUDIES OF TORREFIED WILLOW

Directory of Open Access Journals (Sweden)

Michał Rejdak

2017-01-01

Full Text Available The article presents the results of studies of torrefied willow (Salix viminalis L. compaction. Densification tests were performed using a hydraulic press with a maximum pressure of 216 MPa. The effect of basic parameters of the briquetting process (pressure and temperature on mechanical parameters of manufactured briquettes were determined. On the basis of the research, it was found that the increase in pressure and temperature of the densification process increases the density and strength of pressed briquettes. The positive effect of temperature is particularly noticeable at lower pressing pressures (36 MPa – 72 MPa. In the case of a temperature of 300 °C, the increase in a pressure from 144 MPa to 216 MPa resulted in the decrease in the density and strength of the briquette. It was also found that the briquettes manufactured at this temperature are characterized by lower density and strength than the briquettes obtained at a temperature of 200 °C.

Southwestern willow flycatchers (Empidonax traillii extimus) in a grazed landscape: factors influencing brood parasitism

Science.gov (United States)

Katherine M. Brodhead; Scott H. Stoleson; Deborah M. Finch

2007-01-01

Brood parasitism by Brown-headed Cowbirds (Molothrus ater; hereafter "cowbirds") is an important factor contributing to the endangered status of the Southwestern Willow Flycatcher (Empidonax traillii extimus, hereafter "flycatcher"). We report on factors that influence brood parasitism on the flycatcher using...

Effect of temperature on the uptake and metabolism of cyanide by weeping willows

DEFF Research Database (Denmark)

Yu, X.-Z.; Trapp, Stefan; Zhou, P.-H.

2007-01-01

Plants’ uptake and metabolism of cyanide in response to changes in temperature was investigated. Pre-rooted weeping willows (Salix babylonica L.) were exposed to hydroponic solution spiked with potassium cyanide for 2–3 d. Ten different temperatures were used, ranging from 11◦C to 32◦C. Cyanide...

Phytotoxicity of fresh and weathered diesel and gasoline to willow and poplar trees

DEFF Research Database (Denmark)

Trapp, Stefan; Köhler, A.; Larsen, L.C.

2001-01-01

The toxicity of fresh and weathered gasoline and diesel fuel to willow and poplar trees was studied using a tree transpiration toxicity test. Soils were taken from an abandoned filling station. Concentrations in the samples were measured as the sum of hydrocarbons from C5 to C10 (gasoline) and C1...

Seasonal variation in radiocaesium concentration in willow ptarmigan and rock ptarmigan in central Norway after the Chernobyl fallout

International Nuclear Information System (INIS)

Pedersen, H.C.; Nyboe, S.; Varskog, P.

1998-01-01

Radioactive caesium (20-60 kBq m -2 ) was deposited after the Chernobyl accident in the mountains of central Norway. Two sympatric ptarmigan species, willow ptarmigan Lagopus lagopus and rock ptarmigan L. mutus, inhabit this alpine ecosystem and are important game species. In 1987 and 1988, a study was carried out to try to identify factors affecting radioactive caesium concentration in these birds. Juvenile willow ptarmigan contained more radiocaesium than adults, but the two sexes did not differ in radiocaesium concentration. The radiocaesium concentration of food plants correlated with radiocaesium concentration of rock ptarmigan, and a seasonal variation in radiocaesium concentration of both ptarmigan species was seen. Rock ptarmigan contained more radiocaesium than willow ptarmigan during winter, but not in summer. This difference was related to differences in diet. The bioconcentration factor was 0·4-0·6. The aggregated transfer coefficient was 0·003-0·009 m 2 kg -1 for both species. In spite of the high deposition, the radiocaesium concentration in muscle rarely exceeded the limit recommended for human food consumption (600 Bq kg -1 ). (Copyright (c) 1998 Elsevier Science B.V., Amsterdam. All rights reserved.)

Positive impact of bio-stimulators on growth and physiological activity of willow in climate change conditions

Science.gov (United States)

Piotrowski, Krzysztof; Romanowska-Duda, Zdzisława

2018-04-01

The aim of this research was to evaluate the physiological activity and growth of willow (Salix viminalis L.) plants cultivated under the conditions of adverse temperature and soil moisture content, and to assess the effect of the foliar application of Biojodis (1.0%) and Asahi SL (0.03%) bio-stimulators, or a mixture of Microcistis aeruginosa MKR 0105 and Anabaena PCC 7120 cyanobacteria under such changing growth conditions. The obtained results showed different reactions to the applied constant or periodically changed temperature and soil moisture content. The plants which grew at periodically changed adverse temperature (from -5 to 40oC) or in scantily (20% m.c.) or excessively (60% m.c.) watered soils, grew slowly, in comparison with those growing at 20oC and in optimally moistened soil (30% m.c.). Foliar application of Biojodis and Asahi SL cyanobacteria increased the growth of willow at optimal and adverse temperature or in scantily and excessively moistened soil. The changes in plant growth were associated with the changes in electrolyte leakage, activity of acid or alkaline phosphatases, RNase, index of chlorophyll content in leaves and gas exchange. The above indicates that the foliar application of the studied cyanobacteria and bio-stimulators partly alleviates the harmful impact of adverse temperature and water stress on growth and physiological activity of willow plants

Phytoremediation capacity of poplar (Populus spp. and willow (Salix spp. clonesin relation to photosynthesis

Directory of Open Access Journals (Sweden)

Pajević Slobodanka

2009-01-01

Full Text Available Good photosynthetic features and a favorable water regimes of woody plants improve their survival and remediation potential under unfavorable ecological conditions. Accordingly, we here present results of testing plant tolerance of Pb, Cd, Ni, and diesel fuel based on gas exchange parameters and WUE of four poplar and two willow clones grown in a greenhouse on soil culture. Photosynthesis and transpiration of plants grown on soils with individually applied heavy metals decreased significantly, but this was less obvious in the case of Cd treatment. A heavy metal mixture in the soil induced significant reduction in photosynthesis (by more than 50%. Diesel fuel as the only pollutant in soil caused very strong and significant inhibition of photosynthesis and transpiration of willow clones. The results indicate genotypic specificity of all investigated physiological parameters and mark poplar clones as very useful in phytoextraction technology for the bio-cleaning of chemically polluted soils.

Vegetation and flora of short-rotation willow stands from a conservation viewpoint

Energy Technology Data Exchange (ETDEWEB)

Gustafsson, L.

1986-01-01

The energy forests were studied using random 0.5 x 0.5 m quadrats in which cover for field- and bottom-layer species was recorded in a percentage scale. The data were analysed using various multivariate methods. The vegetation and flora of twelve coppices in southern Sweden were investigated. Also the succession during the establishment phase on a meadow on the west coast and on a peat bog in the east-central part of the country was studied. Moreover, the impact on fen vegetation downstream of an energy forest on a peat bog was investigated. The flora and vegetation of energy forests is dominated by common ruderal species like Cirsium arvense, Galeopsis tetrahit and Urtica dioica. Uncommon species from woodland and fen habitats are only occasionally found. The field layer of energy forests shows a clear seasonality with maximal cover in July. The species number and the composition of vegetation vary greatly between the coppices and is largely determined by the management system. Intense cultivation including fertilization and the use of herbicides depletes the flora. Long rotation times decrease both species diversity and the field-layer cover. Uncommon species are mostly found in old coppices, which also often have a rich spring flora. A change in flora and vegetation occurs when an energy forest is established. The change is great and the time needed for stabilization of the energy forest flora is long when the original flora is dissimilar to the coppice flora. Willow coppices can increase habitat diversity in regions dominated by coniferous forests or in large-scale agricultural areas. Structural heterogeneity of a stand promotes diversity of the flora. Such heterogeneity can be created if a stand is composed of a variety of willow clones, if it is harvested at intervals, contains gaps, open ditches and is surrounded by edge zones of various types.

A genetic linkage map of willow (Salix viminalis) based on AFLP and microsatelite markers

NARCIS (Netherlands)

Hanley, S.; Barker, J.H.A.; Ooijen, van J.W.; Aldam, C.; Harris, S.L.; Ahman, I.; Larsson, S.; Karp, A.

2002-01-01

The genus Salix (willow) contains a number of species of great value as biomass crops. Efforts to breed varieties with improved biomass yields and resistances to pests and diseases are limited by the lack of knowledge on the genetic basis of the traits. We have used AFLP and microsatellite markers

Seismic modelling of coal bed methane strata, Willow Creek, Alberta

Energy Technology Data Exchange (ETDEWEB)

Richardson, S.E.; Mayer, R.; Lawton, D.C.; Langenberg, W. [Consortium for Research in Elastic Wave Exploration Seismology, Calgary, AB (Canada)

2001-07-01

The purpose is to determine the feasibility of applying high- resolution reflection seismic surveying to coalbed methane (CBM) exploration and development. Numerical reflection seismic methods are examined for measuring the mapping continuity and coherence of coal zones. Numerical modelling of a coal zone in Upper Cretaceous sediments near Willow Creek, Alberta indicates that seismic data that is predominantly of 100 Hz is required to map the coal zone and lateral facies variations within the deposit. For resolution of individual coal seams, a central frequency >150 Hz would be needed. 26 refs., 17 figs., 3 tabs.

Porous Carbon with Willow-Leaf-Shaped Pores for High-Performance Supercapacitors.

Science.gov (United States)

Shi, Yanhong; Zhang, Linlin; Schon, Tyler B; Li, Huanhuan; Fan, Chaoying; Li, Xiaoying; Wang, Haifeng; Wu, Xinglong; Xie, Haiming; Sun, Haizhu; Seferos, Dwight S; Zhang, Jingping

2017-12-13

A novel kind of biomass-derived, high-oxygen-containing carbon material doped with nitrogen that has willow-leaf-shaped pores was synthesized. The obtained carbon material has an exotic hierarchical pore structure composed of bowl-shaped macropores, willow-leaf-shaped pores, and an abundance of micropores. This unique hierarchical porous structure provides an effective combination of high current densities and high capacitance because of a pseudocapacitive component that is afforded by the introduction of nitrogen and oxygen dopants. Our synthetic optimization allows further improvements in the performance of this hierarchical porous carbon (HPC) material by providing a high degree of control over the graphitization degree, specific surface area, and pore volume. As a result, a large specific surface area (1093 m 2 g -1 ) and pore volume (0.8379 cm 3 g -1 ) are obtained for HPC-650, which affords fast ion transport because of its short ion-diffusion pathways. HPC-650 exhibits a high specific capacitance of 312 F g -1 at 1 A g -1 , retaining 76.5% of its capacitance at 20 A g -1 . Moreover, it delivers an energy density of 50.2 W h kg -1 at a power density of 1.19 kW kg -1 , which is sufficient to power a yellow-light-emitting diode and operate a commercial scientific calculator.

Preliminary Risk Assessment of the Southwestern Willow Flycatcher (Empidonax traillii extimus) at the Los Alamos National Laboratory

Energy Technology Data Exchange (ETDEWEB)

Gallegos, A.F.; Gonzales, G.J.; Bennett, K.D.; Mullen, M.A.; Foxx, T.S.

1998-10-01

The southwestern willow flycatcher (Empidonax traillii extimus) is the fourth threatened or endangered species to undergo a preliminary assessment for estimating potential risk from environmental contaminants at the Los Alamos National Laboratory. The assessments are being conducted as part of a three-year project to develop a habitat management plan for threatened and endangered species and species of concern at the Laboratory. For the preliminary assessment, estimated doses were compared against toxicity reference values to generate hazard indices (HIs). This assessment included a measure of cumulative effects from multiple contaminants (radionuclides, metals, and organic chemicals) to 100 simulated nest sites located within flycatcher potential habitat. Sources of contaminant values were 10,000-ft{sup 2} grid cells within an Ecological Exposure Unit (EEU). This EEU was estimated around the potential habitat and was based on the maximum home range for the fly catcher identified in the scientific literature. The tools used included a custom FORTRAN program, ECORSK5, and a geographic information system. Food consumption and soil ingestion contaminant pathways were addressed in the assessment. Using a four-category risk evaluation, HI results indicate no appreciable impact is expected to the southwestern willow flycatcher. Information on risk by specific geographical location was generated, which can be used to manage contaminated areas, flycatcher habitat, facility siting, and/or facility operations in order to maintain low levels of risk from contaminants.

Preliminary Risk Assessment of the Southwestern Willow Flycatcher (Empidonax traillii extimus) at the Los Alamos National Laboratory

International Nuclear Information System (INIS)

Gallegos, A.F.; Gonzales, G.J.; Bennett, K.D.; Mullen, M.A.; Foxx, T.S.

1998-01-01

The southwestern willow flycatcher (Empidonax traillii extimus) is the fourth threatened or endangered species to undergo a preliminary assessment for estimating potential risk from environmental contaminants at the Los Alamos National Laboratory. The assessments are being conducted as part of a three-year project to develop a habitat management plan for threatened and endangered species and species of concern at the Laboratory. For the preliminary assessment, estimated doses were compared against toxicity reference values to generate hazard indices (HIs). This assessment included a measure of cumulative effects from multiple contaminants (radionuclides, metals, and organic chemicals) to 100 simulated nest sites located within flycatcher potential habitat. Sources of contaminant values were 10,000-ft 2 grid cells within an Ecological Exposure Unit (EEU). This EEU was estimated around the potential habitat and was based on the maximum home range for the fly catcher identified in the scientific literature. The tools used included a custom FORTRAN program, ECORSK5, and a geographic information system. Food consumption and soil ingestion contaminant pathways were addressed in the assessment. Using a four-category risk evaluation, HI results indicate no appreciable impact is expected to the southwestern willow flycatcher. Information on risk by specific geographical location was generated, which can be used to manage contaminated areas, flycatcher habitat, facility siting, and/or facility operations in order to maintain low levels of risk from contaminants

Paleoseismology of the Nephi Segment of the Wasatch Fault Zone, Juab County, Utah - Preliminary Results From Two Large Exploratory Trenches at Willow Creek

Science.gov (United States)

Machette, Michael N.; Crone, Anthony J.; Personius, Stephen F.; Mahan, Shannon; Dart, Richard L.; Lidke, David J.; Olig, Susan S.

2007-01-01

In 2004, we identified a small parcel of U.S. Forest Service land at the mouth of Willow Creek (about 5 km west of Mona, Utah) that was suitable for trenching. At the Willow Creek site, which is near the middle of the southern strand of the Nephi segment, the WFZ has vertically displaced alluvial-fan deposits >6-7 m, forming large, steep, multiple-event scarps. In May 2005, we dug two 4- to 5-m-deep backhoe trenches at the Willow Creek site, identified three colluvial wedges in each trench, and collected samples of charcoal and A-horizon organic material for AMS (acceleration mass spectrometry) radiocarbon dating, and sampled fine-grained eolian and colluvial sediment for luminescence dating. The trenches yielded a stratigraphic assemblage composed of moderately coarse-grained fluvial and debris-flow deposits and discrete colluvial wedges associated with three faulting events (P1, P2, and P3). About one-half of the net vertical displacement is accommodated by monoclinal tilting of fan deposits on the hanging-wall block, possibly related to massive ductile landslide deposits that are present beneath the Willow Creek fan. The timing of the three surface-faulting events is bracketed by radiocarbon dates and results in a much different fault chronology and higher slip rates than previously considered for this segment of the Wasatch fault zone.

Phytoscreening and phytoextraction of heavy metals at Danish polluted sites using willow and poplar trees

DEFF Research Database (Denmark)

Nielsen, Mette Algreen; Trapp, Stefan; Rein, Arno

2014-01-01

The main purpose of this study was to determine typical concentrations of heavy metals (HM) in wood from willows and poplars, in order to test the feasibility of phytoscreening and phytoextraction of HM. Samples were taken from one strongly, one moderately, and one slightly polluted site and from...

A habitat overlap analysis derived from Maxent for Tamarisk and the South-western Willow Flycatcher

Science.gov (United States)

Patricia York; Paul Evangelista; Sunil Kumar; James Graham; Curtis Flather; Thomas Stohlgren

2011-01-01

Biologic control of the introduced and invasive, woody plant tamarisk (Tamarix spp, saltcedar) in south-western states is controversial because it affects habitat of the federally endangered South-western Willow Flycatcher (Empidonax traillii extimus). These songbirds sometimes nest in tamarisk where floodplain-level invasion replaces native habitats. Biologic control...

The neutral species of the weak base trimethoprim is more toxic to willow trees (Salix viminalis) than the cation

DEFF Research Database (Denmark)

Mikes, O.; Trapp, Stefan

2011-01-01

The acute toxicity of the veterinary antibiotic trimethoprim (TMP) to willow trees was tested at three different pH levels in hydroponic solutions with TMP concentrations of 1, 10, 100 or 1000 mg/L. The pH variation was achieved by using ammonium (pH 4.3, low) or nitrate (pH 6.4, medium) as nitro......The acute toxicity of the veterinary antibiotic trimethoprim (TMP) to willow trees was tested at three different pH levels in hydroponic solutions with TMP concentrations of 1, 10, 100 or 1000 mg/L. The pH variation was achieved by using ammonium (pH 4.3, low) or nitrate (pH 6.4, medium...

Meta-transcriptomics indicates biotic cross-tolerance in willow trees cultivated on petroleum hydrocarbon contaminated soil.

Science.gov (United States)

Gonzalez, Emmanuel; Brereton, Nicholas J B; Marleau, Julie; Guidi Nissim, Werther; Labrecque, Michel; Pitre, Frederic E; Joly, Simon

2015-10-12

High concentrations of petroleum hydrocarbon (PHC) pollution can be hazardous to human health and leave soils incapable of supporting agricultural crops. A cheap solution, which can help restore biodiversity and bring land back to productivity, is cultivation of high biomass yielding willow trees. However, the genetic mechanisms which allow these fast-growing trees to tolerate PHCs are as yet unclear. Salix purpurea 'Fish Creek' trees were pot-grown in soil from a former petroleum refinery, either lacking or enriched with C10-C50 PHCs. De novo assembled transcriptomes were compared between tree organs and impartially annotated without a priori constraint to any organism. Over 45% of differentially expressed genes originated from foreign organisms, the majority from the two-spotted spidermite, Tetranychus urticae. Over 99% of T. urticae transcripts were differentially expressed with greater abundance in non-contaminated trees. Plant transcripts involved in the polypropanoid pathway, including phenylalanine ammonia-lyase (PAL), had greater expression in contaminated trees whereas most resistance genes showed higher expression in non-contaminated trees. The impartial approach to annotation of the de novo transcriptomes, allowing for the possibility for multiple species identification, was essential for interpretation of the crop's response treatment. The meta-transcriptomic pattern of expression suggests a cross-tolerance mechanism whereby abiotic stress resistance systems provide improved biotic resistance. These findings highlight a valuable but complex biotic and abiotic stress response to real-world, multidimensional contamination which could, in part, help explain why crops such as willow can produce uniquely high biomass yields on challenging marginal land.

Expression of zinc and cadmium responsive genes in leaves of willow (Salix caprea L.) genotypes with different accumulation characteristics

International Nuclear Information System (INIS)

Konlechner, Cornelia; Türktaş, Mine; Langer, Ingrid; Vaculík, Marek; Wenzel, Walter W.; Puschenreiter, Markus; Hauser, Marie-Theres

2013-01-01

Salix caprea is well suited for phytoextraction strategies. In a previous survey we showed that genetically distinct S. caprea plants isolated from metal-polluted and unpolluted sites differed in their zinc (Zn) and cadmium (Cd) tolerance and accumulation abilities. To determine the molecular basis of this difference we examined putative homologues of genes involved in heavy metal responses and identified over 200 new candidates with a suppression subtractive hybridization (SSH) screen. Quantitative expression analyses of 20 genes in leaves revealed that some metallothioneins and cell wall modifying genes were induced irrespective of the genotype's origin and metal uptake capacity while a cysteine biosynthesis gene was expressed constitutively higher in the metallicolous genotype. The third and largest group of genes was only induced in the metallicolous genotype. These data demonstrate that naturally adapted woody non-model species can help to discover potential novel molecular mechanisms for metal accumulation and tolerance. -- Highlights: ► The transcriptional Zn/Cd response of the willow Salix caprea was quantified. ► Two genotypes from a highly contaminated and a control environment were compared. ► In addition to candidate genes an SSH library revealed over 200 metal induced genes. ► Constitutive upregulation and isolate-specific induction of genes were revealed. ► Willows adapt to environmental Zn/Cd contamination on the transcriptional level. -- Expression analyzes reveal different responses to Cd and Zn exposure of S. caprea genotypes with different heavy metal accumulation abilities

Concentrations of Chemical Elements in Willow Biomass Depend on Clone, Site and Management in the Field

DEFF Research Database (Denmark)

Liu, Na; Jørgensen, Uffe; Lærke, Poul Erik

2016-01-01

Eight willow (Salix) clones (Inger, Klara, Linnea, Resolution, Stina, Terra Nova, Tora, Tordis) were planted on two soil types in Denmark. The biomass quality was evaluated after 3 years of growth by measuring differences in concentrations of 14 elements associated with ash behavior during combus...

Integrated long-term responses of an arctic-alpine willow and associated ectomycorrhizal fungi to an altered environment

DEFF Research Database (Denmark)

Clemmensen, Karina Engelbrecht; Michelsen, Anders

2006-01-01

We evaluated ectomycorrhizal (ECM) colonization and morphotype community composition together with growth response and biomass distribution in the arctic-alpine, prostrate willow Salix herbacea L. x Salix polaris Wahlenb. after 11 seasons of shading, warming, and fertilization at a fellfield...

Salicin from Willow Bark can Modulate Neurite Outgrowth in Human Neuroblastoma SH-SY5Y Cells.

Science.gov (United States)

Wölfle, Ute; Haarhaus, Birgit; Kersten, Astrid; Fiebich, Bernd; Hug, Martin J; Schempp, Christoph M

2015-10-01

Salicin from willow bark has been used throughout centuries in China and Europe for the treatment of pain, headache, and inflammatory conditions. Recently, it could be demonstrated that salicin binds and activates the bitter taste receptor TAS2R16. Studies on rodent tissues showed the general expression of bitter taste receptors (TAS2Rs) in rodent brain. Here, we demonstrate the expression of hTAS2R16 in human neuronal tissues and the neuroblastoma cell line SH-SY5Y. The functionality was analyzed in the neuroblastoma cell line SH-SY5Y after stimulation with salicin, a known TAS2R16 agonist. In this setting salicin induced in SH-SY5Y cells phosphorylation of ERK and CREB, the key transcription factor of neuronal differentiation. PD98059, an inhibitor of the ERK pathway, as well as probenecid, a TAS2R16 antagonist, inhibited receptor phosphorylation as well as neurite outgrowth. These data show that salicin might modulate neurite outgrowth by bitter taste receptor activation. Copyright © 2015 John Wiley & Sons, Ltd.

Development of an applied black willow tree improvement program for biomass production in the south

Science.gov (United States)

Randall J. Rousseau; Emile S. Gardiner; Theodor D. Leininger

2012-01-01

The development of rapidly growing biomass woody crops is imperative as the United States strives to meet renewable energy goals. The Department of Energy has indicated that biomass is a prime source for renewable energy for the southern United States. Black Willow (Salix nigra Marsh.) is a potential bioenergy/biofuels crop for dedicated short-...

Cd and Zn concentrations in small mammals and willow leaves on disposal facilities for dredged material

NARCIS (Netherlands)

Mertens, J.; Luyssaert, S.; Verbeeren, S.; Vervaeke, P; Lust, N

2001-01-01

Disposal sites for dredged material are often polluted with heavy metals. The uptake of Cd and Zn by small mammals and willow trees was assessed on three sites with a different pollution degree. Detailed soil sampling showed a huge variation in soil characteristics within the sites, typical for

Annual variations in the solar energy conversion efficiency in a willow coppice stand

International Nuclear Information System (INIS)

Noronha-Sannervik, A.; Kowalik, P.

2003-01-01

Productivity of an experimental willow coppice forest located at Uppsala, Sweden, was monitored between 1985 and 1994. The 2.7 ha stand was planted in 1984 with a density of 20 000 cuttings per ha and was harvested three times. During the monitored period, the annual stem wood production and the cumulated values of total solar radiation during the growing season, were measured. The conversion of incoming solar radiation into stem biomass was evaluated and the results show that the solar energy conversion efficiency (ECE), for the first and fourth year of the cutting cycle, is, on average, 64% of the ECE for the second and third year of the cutting cycle. It is discussed that the low ECE of 1-year-old shoots is related to a delay in leaf canopy development at the beginning of the growing season and lack of weed control after harvest. For the 4-years-old shoots, the low ECE, is believed to be related to the increased shoot and stool mortality caused by the self-thinning process ongoing in the willow stand. It is recommended that the harvesting interval should be based on the specific development of the stand and more attention should be paid to weed control, especially in the first growing season after harvest

Dry matter losses and quality changes during short rotation coppice willow storage in chip or rod form.

Science.gov (United States)

Whittaker, Carly; Yates, Nicola E; Powers, Stephen J; Misselbrook, Tom; Shield, Ian

2018-05-01

This study compares dry matter losses and quality changes during the storage of SRC willow as chips and as rods. A wood chip stack consisting of approximately 74 tonnes of fresh biomass, or 31 tonnes dry matter (DM) was built after harvesting in the spring. Three weeks later, four smaller stacks of rods with an average weight of 0.8 tonnes, or 0.4 tonnes DM were built. During the course of the experiment temperature recorders placed in the stacks found that the wood chip pile reached 60 °C within 10 days of construction, but the piles of rods remained mostly at ambient temperatures. Dry matter losses were calculated by using pre-weighed independent samples within the stacks and by weighing the whole stack before and after storage. After 6 months the wood chip stack showed a DM loss of between 19.8 and 22.6%, and mean losses of 23.1% were measured from the 17 independent samples. In comparison, the rod stacks showed an average stack DM loss of between 0 and 9%, and between 1.4% and 10.6% loss from the independent samples. Analysis of the stored material suggests that storing willow in small piles of rods produces a higher quality fuel in terms of lower moisture and ash content; however, it has a higher fine content compared to storage in chip form. Therefore, according to the two storage methods tested here, there may be a compromise between maximising the net dry matter yield from SRC willow and the final fine content of the fuel.

Sampling procedure in a willow plantation for estimation of moisture content

DEFF Research Database (Denmark)

Nielsen, Henrik Kofoed; Lærke, Poul Erik; Liu, Na

2015-01-01

Heating value and fuel quality of wood is closely connected to moisture content. In this work the variation of moisture content (MC) of short rotation coppice (SRC) willow shoots is described for five clones during one harvesting season. Subsequently an appropriate sampling procedure minimising...... labour costs and sampling uncertainty is proposed, where the MC of a single stem section with the length of 10–50 cm corresponds to the mean shoot moisture content (MSMC) with a bias of maximum 11 g kg−1. This bias can be reduced by selecting the stem section according to the particular clone...

The effects of first-year shoot cut back on willow biomass production during the first and second cutting cycle; Effekter av skottnedklippning efter etableringsaaret paa produktionen under foersta och andra omdrevet i salixodlingar

Energy Technology Data Exchange (ETDEWEB)

Verwijst, Theo; Nordh, Nils-Erik

2010-05-15

During the early phase of commercialisation of willow short rotation forestry in Sweden it was considered to be important to cut down the shoots after the establishment year, and this practice still is maintained today. Several reasons then were put forward for cutting down. The primary goal was to stimulate sprouting of more shoots, thereby obtaining a rapidly closing stand which could compete with weeds. Another reason was that it would enable weed control during the second year. In some of the older clones, which exhibited bow-shaped shoots, cutting down was supposed to lead to more straight growing shoots which rendered less biomass loss at harvest. In the meantime, the practice of cutting down has been abandoned in Denmark, and there are reasons to scrutinise the effects of cutting down on available biomass production figures from Swedish field trials. The main goal with this project was to try to quantify the effects of cutting down on the biomass productivity of willow during the first and later cutting cycles. Thus far, efforts in this research topic have not led to a scientifically documented quantification on the effects, and therefore a scientific basis for hands-on recommendations to willow growers is lacking. The purpose of our work consequently was to generate practical recommendations with regard to the management measure of cutting down, and the audience targeted consisted of willow growers (farmers, land-owners and entrepreneurs) who are deciding about and perform the actual management of willow stands to obtain higher yields. This information also is of large relevance for all extension workers in willow growing. Data have been collected from a field trial which was planted in Flosta, Enkoeping, in 2005. As this was the only experiment on cutting down which ran during the project period, we searched the archives which contained material from another experiment which ran from 1992 to 1996 in Ultuna, Uppsala, and from which some date were collected

Enzymatic Saccharification of Shrub Willow Genotypes with Differing Biomass Composition for Biofuel Production

Directory of Open Access Journals (Sweden)

Michelle J. Serapiglia

2013-03-01

Full Text Available In the conversion of woody biomass feedstocks into liquid fuel ethanol, the pretreatment process is the most critical and costly step. Variations in biomass composition based on genetic differences or environmental effects have a significant impact on the degree of accessibility accomplished by pretreatment and subsequent sugar release by enzymatic hydrolysis. To evaluate this, biomass from 10 genetically diverse, genotypes of shrub willow (Salix spp. was pretreated with a hot-water process at two levels of severity, hydrolyzed using a combination of two commercial enzyme cocktails, and the release of hexose and pentose monomers was quantified by HPLC. Among the genotypes selected for analysis, cellulose content ranged from 39 to 45% (w/w and lignin content ranged from 20 to 23% (w/w at harvest. Differences in the effectiveness of the pretreatment process were observed among the various willow genotypes. Correlations were identified between total sugar release and % cellulose and % lignin content. There was a significant effect of pretreatment severity on polysaccharide accessibility, but the response to pretreatments was different among the genotypes. At the high severity pretreatment ‘SV1’ was the least recalcitrant with sugar release representing as much as 60% of total biomass. These results suggest that structural, as well as chemical characteristics of the biomass may influence pretreatment and hydrolytic efficiency.

Combustion quality of poplar and willow clones grown as SRC at four sites in Brandenburg, Germany

DEFF Research Database (Denmark)

Liu, Na; Ugilt Larsen, Søren; Jørgensen, Uffe

2017-01-01

The fuel quality was assessed for nine poplar clones (AF2, Androscoggin, Max1, Max3, Max4, Monviso, Muhle-Larsen, NE42, Weser6) and one willow clone (Inger) grown as short rotation coppice (SRC) on four sites in the Brandenburg area in Germany. Fuel quality was analysed in 3-year old shoots in te...

Distribution and abundance of Least Bell’s Vireos (Vireo bellii pusillus) and Southwestern Willow Flycatchers (Empidonax traillii extimus) on the Middle San Luis Rey River, San Diego County, southern California—2017 data summary

Science.gov (United States)

Allen, Lisa D.; Howell, Scarlett L.; Kus, Barbara E.

2018-04-20

We surveyed for Least Bell’s Vireos (LBVI) (Vireo bellii pusillus) and Southwestern Willow Flycatchers (SWFL) (Empidonax traillii extimus) along the San Luis Rey River, between College Boulevard in Oceanside and Interstate 15 in Fallbrook, California (middle San Luis Rey River), in 2017. Surveys were conducted from April 13 to July 11 (LBVI) and from May 16 to July 28 (SWFL). We found 146 LBVI territories, at least 107 of which were occupied by pairs. Five additional transient LBVIs were detected. LBVIs used five different habitat types in the survey area: mixed willow, willow-cottonwood, willow-sycamore, riparian scrub, and upland scrub. Forty-four percent of the LBVIs occurred in habitat characterized as mixed willow and 89 percent of the LBVI territories occurred in areas with greater than 50 percent native plant cover. Of 16 banded LBVIs detected in the survey area, 8 had been given full color-band combinations prior to 2017. Four other LBVIs with single (natal) federal bands were recaptured and banded in 2017. Three LBVIs with single dark blue federal bands indicating that they were banded as nestlings on the lower San Luis Rey River and one LBVI with a single gold federal band indicating that it was banded as a nestling on Marine Corps Base Camp Pendleton (MCBCP) could not be recaptured for identification. One banded LBVI emigrated from the middle San Luis Rey River to the lower San Luis Rey River in 2017.One resident SWFL territory and one transient Willow Flycatcher of unknown subspecies (WIFL) were observed in the survey area in 2017. The resident SWFL territory, which was comprised of mixed willow habitat (5–50 percent native plant cover), was occupied by a single male from May 22 to June 21, 2017. No evidence of pairing or nesting activity was observed. The SWFL male was banded with a full color-combination indicating that he was originally banded as a nestling on the middle San Luis Rey River in 2014 and successfully bred in the survey area in 2016

On the irrigation requirements of cottonwood (Populus fremontii and Populus deltoides var. wislizenii) and willow (Salix gooddingii) grown in a desert environment

Science.gov (United States)

Hartwell, S.; Morino, K.; Nagler, P.L.; Glenn, E.P.

2010-01-01

Native tree plots have been established in river irrigation districts in the western U.S. to provide habitat for threatened and endangered birds. Information is needed on the effective irrigation requirements of the target species. Cottonwood (Populus spp.) and willow (Salix gooddingii) trees were grown for seven years in an outdoor plot in a desert environment in Tucson, Arizona. Plants were allowed to achieve a nearly complete canopy cover over the first four years, then were subjected to three daily summer irrigation schedules of 6.20??mm??d-1; 8.26??mm??d-1 and 15.7??mm??d-1. The lowest irrigation rate was sufficient to maintain growth and high leaf area index for cottonwoods over three years, while willows suffered considerable die-back on this rate in years six and seven. These irrigation rates were applied April 15-September 15, but only 0.88??mm??d-1 was applied during the dormant period of the year. Expressed as a fraction of reference crop evapotranspiration (ETo), recommended annual water applications plus precipitation (and including some deep drainage) were 0.83 ETo for cottonwood and 1.01 ETo for willow. Current practices tend to over-irrigate restoration plots, and this study can provide guidelines for more efficient water use. ?? 2010 Elsevier Ltd.

Growth, physiological response and phytoremoval capability of two willow clones exposed to ibuprofen under hydroponic culture.

Science.gov (United States)

Iori, Valentina; Zacchini, Massimo; Pietrini, Fabrizio

2013-11-15

Ibuprofen (IBU) is one of the most widespread pharmaceuticals in the aquatic ecosystem, despite the high removal rate that occurs in wastewater treatment plants. Phytoremediation represents a technology to improve the performance of existing wastewater treatment. This study was conducted under hydroponics to evaluate the ability of Salicaceae plants to tolerate and reduce IBU concentration in contaminated water. To this end, we combined growth, physiological and biochemical data to study the effects of different IBU concentrations on two clones of Salix alba L. Data demonstrated that clone SS5 was more tolerant and showed a higher ability to reduce IBU concentration in the solution than clone SP3. The high tolerance to IBU shown by SS5 was likely due to several mechanisms including the capacity to maintain an elevated photosynthetic activity and an efficient antioxidative defence. These results illustrate the remarkable potential of willow to phytoremediate IBU-contaminated waters in natural and constructed wetlands. Copyright © 2013 Elsevier B.V. All rights reserved.

El Alzado de la Vivienda en Willow Road Ernö Goldfinger

Directory of Open Access Journals (Sweden)

Ignacio Román Santiago

2015-05-01

Full Text Available ResumenEl artículo propone aproximarse a la vivienda que el arquitecto húngaro Ernö Goldfinger construyó para sí mismo en 1939 en el barrio de Hampstead (Londres. El complejo y singular ejercicio en el que Goldfinger apoya gran parte de sus teorías se manifiesta en esta propuesta para Willow Road y se desvela especialmente en su fachada. Para el arquitecto es fundamental estudiar la experiencia humana del espacio arquitectónico relacionada con la envolvente del edificio y, en este sentido, sulegado teórico se expresa en los textos que escribió para la revista Architectural Review entre los años 1941 y 1942: The Sensation of Space, Urbanism and Spatial Order y Elements of Enclosed Space.Analizar este alzado enigmático provoca algunos interrogantes que son, en sí mismos, un auténtico manifi esto a favor de una arquitectura libre de toda adscripción estilística. Goldfinger actúa aquí en una mesa de laboratorio donde pone a prueba sus reflexiones sobre el orden espacial, la composición, la escala, el carácter y la construcción.De esta forma la propuesta para Willow Road no puede explicarse exclusivamente en términos funcionales ni mecanicistas, sino que precisa una visión fenomenológica y al mismo tiempo mirarlo con amplitud para empezar a descubrir sus claves. Este hogar, que puede entenderse como vivienda burguesa y también representa un ejercicio moderno, ofrece la oportunidad de desvelar un modo de hacer, muy particular, en el que algunos arquitectos desarraigados y liberados del imperante tradicionalismo inglés y de cualquier dogmatismo, dejan a un lado el itinerario que cabría esperar en aquel momento y 'contaminan' la arquitectura moderna inglesa, para producir un panorama de influencias difícil de reconocer en cualquier otra localización. La huella de esta modernidad revisada, de espíritu inequívocamente moderno pero filtrado desde una actitud clásica, influye en la siguiente generación de arquitectos ingleses

Evaluation of spectral light management on growth of container-grown willow oak, nuttall oak and summer red maple

Science.gov (United States)

Plant response to blue, red, gray or black shade cloth was evaluated with willow oak (Quercus phellos L.), Nuttall oak (Quercus nuttallii Palmer, Nuttall) and Summer Red maple (Acer rubrum L. ‘Summer Red’) liners. Light transmitted through the colored shade cloth had no influence on germination of ...

Willow Creek Wildlife Mitigation Project. Final environmental assessment

International Nuclear Information System (INIS)

1995-04-01

Today's notice announces BPA's proposal to fund land acquisition or acquisition of a conservation easement and a wildlife management plan to protect and enhance wildlife habitat at the Willow Creek Natural Area in Eugene, Oregon. This action would provide partial mitigation for wildlife and wildlife habitat lost by the development of Federal hydroelectric projects in the Willamette River Basin. The project is consistent with BPA's obligations under provisions of the Pacific Northwest Electric Power Planning and Conservation Act of 1980 as outlined by the Northwest Power Planning Council's 1994 Columbia River Basin Fish and Wildlife Program. BPA has prepared an environmental assessment (DOE/EA-1023) evaluating the proposed project. Based on the analysis in the EA, BPA has determined that the proposed action is not a major Federal action significantly affecting the quality of the human environment, within the meaning of the National Environmental Policy Act (NEPA) of 1969. Therefore, the preparation of an environmental impact statement (EIS) is not required and BPA is issuing this FONSI

Quality Testing of Short Rotation Coppice Willow Cuttings

Directory of Open Access Journals (Sweden)

Katrin Heinsoo

2018-06-01

Full Text Available The production and feasibility of Short Rotation Coppice depend on cutting early performance. The shoot and root biomass production of Salix cuttings in hydroponic conditions was studied. The amount of sprouted biomass after four weeks of growth depended on cutting the diameter, but the original position of the cutting along the rod or number of visible buds was not in correlation with biomass produced. Application of mineral fertilizer or soil originating from the willow plantation did not increase the total production. On the contrary, the addition of soil tended to decrease biomass production and we assumed this was a result of a shortage of light. Under the influence of fertilization, plants allocated greater biomass to roots. Comparison of different clones revealed that those with S. dasyclados genes tended to allocate less biomass to roots and the poorest-performing clone in our experiment, also had the lowest wood production in the plantation. The number of visible buds on the cutting was also clone-specific.

Environmental effects of energy forest (short rotation willow)

International Nuclear Information System (INIS)

Frank, K.

1994-01-01

This paper deals with environmental effects of producing and combusting energy forest fuel. Energy forest means short rotation willow (Salix). Supposed effects of sewage sludge application are discussed as well. Energy forestry on agricultural land implies both advantages and disadvantages for the environment. Leaf litter (humified leaves) increases the humus content in the top soil. The soil fauna is also positively affected. Until now performed studies about nitrogen leakage from fields cultivated with energy forest (Salix), have not given any distinct results. A retarded drainage within energy forest fields is on the other hand noticed. While the root system of Salix is active during a long period of the year, the nitrogen leakage become less compared to traditional cultivation. The content of plant nutrients and organic matter in sewage sludge make a resource that can be useful for agricultural purposes, especially for energy forest cultivation. The content of heavy metals and organic emissions contradicts sludge application to agricultural land. Sewage sludge with todays quality increases somewhat the content of heavy metals in the soil. This condition can be counteracted to a certain extent by growing energy forest. It has been established that Salix has high ability to heavy metal uptake, especially cadmium. Growing energy forest on drained farm land is connected with a risk for root penetration into the drainage system. With enough water and plant nutrients in the top soil the risk is reduced. Shallow depth of the pipes increases the risk. Combustion of wood chip from energy forests (and other types of biomass) gives especially two advantages. It does not give any net contribution of carbon dioxide to the atmosphere. The sulphur discharge will be minimal since the sulphur content in wood fuels is low. Discharge of nitrogen oxide and hydrocarbons may give some problems. These can be reduced by technological measures when combusting. 27 refs, 4 tabs

Biomass yield and fuel characteristics of short-rotation coppice (willow, poplar, empress tree)

Energy Technology Data Exchange (ETDEWEB)

Maier, J.; Vetter, R. [Institute for Land Management Compatible to Environmental Requirements, Muellheim (Germany)

2004-07-01

In two pedo-climatic different regions in the state of Baden-Wuerttemberg three shortrotation coppices willow, poplar and empress tree were tested with regard to their biomass productivity on arable land and to their properties for energetic use. Between 8 and 13 tons of dry matter per hectare and year could be produced under extensive cultivation conditions, over 15 tons with irrigation. Due to their composition, it can be assumed that their use as solid fuel in a biomass combustor is just as unproblematic as with forest timber. (orig.)

Cargo Data Management Demonstration System

Science.gov (United States)

1974-02-01

Delays in receipt and creation of cargo documents are a problem in international trade. The work described demonstrates some of the advantages and capabilities of a computer-based cargo data management system. A demonstration system for data manageme...

Short-rotation Willow Biomass Plantations Irrigated and Fertilised with Wastewaters. Results from a 4-year multidisciplinary field project in Sweden, France, Northern Ireland and Greece

Energy Technology Data Exchange (ETDEWEB)

Larsson, Stig [Svaloef Weibull AB, Svaloef (Sweden); Cuingnet, Christian; Clause, Pierre [Association pour le Developpement des Culture Energetiques, Lille (France); Jakobsson, Ingvar [Swedish Univ. of Agricultural Sciences, Uppsala (Sweden); Dawson, Malcolm [Queens Univ., Northern Ireland (United Kingdom); Backlund, Arne [A and B Backlund ApS, Charlottenlund (Denmark); Mavrogianopoulus, George [Agricultural Univ. of Athens (Greece)

2003-01-01

This report summarises results and experiences gathered from field trials with recycling of pre-treated wastewater, diverted human urine mixed with water, and municipal sludge, within plantations of willow species specifically selected for biomass production. Experimental sites were established in Sweden (Roma), France (Orchies), Northern Ireland (Culmore) and Greece (Larissa). The project was carried out during a 4-year period with financial support from the EU FAIR Programme. The experimental sites were supplied with primary effluent from municipal treatment plants (Culmore and Larissa), stored industrial effluent from a chicory processing plant (Orchies), biologically treated and stored municipal wastewater (Roma) and human urine mixture from diverting low-flush toilets mixed with water (Roma). Application rates of the wastewaters or the urine mixture were equivalent to the calculated evapotranspiration rate at each site. Wastewaters were also applied up to three times this value to evaluate any possible negative effects. Estimations and evaluations were carried out mainly concerning: biomass growth, potential biological attacks of the plantations, plant water requirements, fertilisation effects of the wastewater, plant uptake of nutrients and heavy metals from applied wastewater, possible soil or groundwater impact, sanitary aspects, and potentials for removal in the soil-plant filter of nutrients and biodegradable organic material from applied wastewater. The results clearly indicated that biomass production in young willow plantations could be enhanced substantially after recycling of wastewater resources. The impact on soil and groundwater of nutrients (nitrogen and phosphorus) and heavy metals (copper, zinc, lead and cadmium) was limited, even when the application of water and nutrients exceeded the plant requirements. Also, the soil-plant system seemed to function as a natural treatment filter for pre-treated (primary settled) wastewater, with a treatment

3. Rethinking Borders in Empire and Nation at the Foot of the Willow Palisade

OpenAIRE

E.Bulag, Uradyn

2015-01-01

Prologue: stony wars at the foot of the willow palisade Every year, on the fifth day of the fifth lunar month, i.e. the traditional Duanwu Festival (also known as Dragon Boat Festival or Double Fifth Festival), people in Wangsiyingzi and the neighbouring village Sifangtai, just about one and half kilometres to the south, would climb atop a small mountain that lies between the two villages. Instead of racing dragon-headed boats as is the practice in south China, where the tradition first start...

DETERMINATION OF FLAVONOIDS OF WILLOW TRIANDRA (SALIX TRIANDRA L., GROWING IN THE NORTH CAUCASUS

Directory of Open Access Journals (Sweden)

E. G. Sannikova

2016-01-01

Full Text Available Plants of willow genus are rich in various flavonoids. In 60-e years of the XX century the works of V. A. Kompantsev showed that leaves of willow triandra, growing in the North Caucasus, contain up to 5% of rutin. The method, which required long sample preparation (extraction of the raw material with TLC, chromatographic layer extraction with methanol, removal of the solvent, dissolution in ethanol, optical density measurements was used. Currently available and simple methods for the determination of rutin in plant material are described. Given that leaves of Salix triandra contain significant amounts of rutin and can be a potential raw material for the creation of medicines on their basis, it is essential to determine the amount of flavonoids in the leaves of Salix triandra and its branches.The purpose of this study is determination of the amount of flavonoids in the willow triandra, growing in the North Caucasus, depending on the place and time of collection.Methods. TLC and the method of differential spectrophotometry were used to study chemical reactions. Results. The presence of flavonoids in various vegetative plant organs was established using qualitative reactions (cyanidin test; boric-citric reaction; the reaction with solution of lead acetate and solution of ammonia. Rutin and quercetin flavonoids in the presence of standard samples were identified using TLC. the method of differential spectrophotometry, based on the reaction of flavonoids with aluminum chloride was used for the quantitative determination of the amount of flavonoids. It is shown that the greatest quantity of flavonoids amount accumulated in the leaves (up to 3.76%, its value in branches is slightly smaller (up to 3.26%. The branches without leaves have almost 10 times less flavonoids. It was established experimentally that the accumulation of flavonoids in raw material of Salix triandra is dependent on the place and time of

Geographic variation in the song of Willow Flycatchers: Differentiation between Empidonax traillii adastus and E. t. extimus

Science.gov (United States)

Sedgwick, J.A.

2001-01-01

The vocal signatures of the primary song form (“fitz-bew”) of the endangered Southwestern Willow Flycatcher (Empidonax traillii extimus) and its northern counterpart, E. t. adastus, are distinctive. Songs of the extimus subspecies are longer (total song, note, internote) and frequencies at maximum amplitude are lower than those of adastus. I used vocal evidence to clarify the distributional limits of the Southwestern Willow Flycatcher and that of the geographically adjacent subspecies, E. t. adastus. Unweighted pair-group method using averaging (UPGMA) cluster analysis and canonical discriminant analysis revealed that (1) low elevation, southerly desert populations (Arizona, New Mexico, and southern Utah) have a unique vocal identity corresponding to populations in the range of E. t. extimus; (2) northerly song groups (Oregon, Colorado, and northern Utah) share a different song type corresponding to populations in the range of E. t. adastus; and (3) a departure from vocal and morphological congruence occurs for a population of high-elevation Arizona birds that, although in the currently accepted range of E. t. extimus, sings songs acoustically similar to more northern populations (E. t. adastus). Multiple regression of song distance on latitude and elevation, and a comparison of a matrix of song distances with a matrix of latitude and elevation dissimilarities, demonstrated that song populations sort out by both latitude and elevation: birds with the vocal identity of extimus occur as far north as 37°N if at low elevation, and those acoustically similar to adastus occur as far south as 33.7°N if at high elevation. The vocal background of northern New Mexico birds appears to be intermediate between that of extimus and adastus, suggesting that northern New Mexico is a zone of intermixing and intergradation between the subspecies. Pure forms of E. t. extimus apparently do not occur in Colorado because even the southernmost populations are acoustically similar to

Willow Creek Wildlife Mitigation Project. Final Environmental Assessment.

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-04-01

Today`s notice announces BPA`s proposal to fund land acquisition or acquisition of a conservation easement and a wildlife management plan to protect and enhance wildlife habitat at the Willow Creek Natural Area in Eugene, Oregon. This action would provide partial mitigation for wildlife and wildlife habitat lost by the development of Federal hydroelectric projects in the Willamette River Basin. The project is consistent with BPA`s obligations under provisions of the Pacific Northwest Electric Power Planning and Conservation Act of 1980 as outlined by the Northwest Power Planning Council`s 1994 Columbia River Basin Fish and Wildlife Program. BPA has prepared an environmental assessment (DOE/EA-1023) evaluating the proposed project. Based on the analysis in the EA, BPA has determined that the proposed action is not a major Federal action significantly affecting the quality of the human environment, within the meaning of the National Environmental Policy Act (NEPA) of 1969. Therefore, the preparation of an environmental impact statement (EIS) is not required and BPA is issuing this FONSI.

Investigation of Solid Energy Potential of Wood and Bark Obtained from Four Clones of a 2-Year Old Goat Willow

International Nuclear Information System (INIS)

Han, Sim-Hee; Shin, Soo-Jeong

2014-01-01

To investigate the solid raw material characteristics of willow (Salix caprea) bark and woody core, this study analyzed overall chemical composition, monosaccharide composition, ash content, and main ash composition of both tree components. Significant differences were observed between the two in terms of chemical composition, carbohydrate composition, ash content, and major inorganics. The ash content in bark was 3.8–4.7%, compared with 0.6–1.1% in the woody core. Polysaccharide content in the woody core was 62.8–70.6% but was as low as 44.1–47.6% in the bark. The main hemicelluloses consisting of monosaccharides were xylose in the case of the woody core, and xylose, galactose, and arabinose in the case of bark. Woody core biomass of willow provides superior solid fuel raw material, as compared with bark biomass, with higher heating values, less ash content, and less slagging-causing material.

Investigation of Solid Energy Potential of Wood and Bark Obtained from Four Clones of a 2-Year Old Goat Willow

Energy Technology Data Exchange (ETDEWEB)

Han, Sim-Hee [Department of Forest Genetic Resources, Korea Forest Research Institute, Suwon (Korea, Republic of); Shin, Soo-Jeong, E-mail: soojshin@cbnu.ac.kr [Department of Wood and Paper Science, Chungbuk National University, Cheongju (Korea, Republic of)

2014-01-31

To investigate the solid raw material characteristics of willow (Salix caprea) bark and woody core, this study analyzed overall chemical composition, monosaccharide composition, ash content, and main ash composition of both tree components. Significant differences were observed between the two in terms of chemical composition, carbohydrate composition, ash content, and major inorganics. The ash content in bark was 3.8–4.7%, compared with 0.6–1.1% in the woody core. Polysaccharide content in the woody core was 62.8–70.6% but was as low as 44.1–47.6% in the bark. The main hemicelluloses consisting of monosaccharides were xylose in the case of the woody core, and xylose, galactose, and arabinose in the case of bark. Woody core biomass of willow provides superior solid fuel raw material, as compared with bark biomass, with higher heating values, less ash content, and less slagging-causing material.

The silviculture, nutrition and economics of short rotation willow coppice in the uplands of mid-Wales

Energy Technology Data Exchange (ETDEWEB)

Heaton, R J; Randerson, P F; Slater, F M

2000-07-01

The potential of short rotation coppice as a biomass crop on land over 250m (the uplands) of mid Wales was studied. The results found in this study indicate that growing short rotation coppice willow in the uplands is a viable proposition with regard to establishment success and yields. In the event of a secure wood chip market in Wales, returns to the grower would be comparable to those from sheep production. (author)

Short-rotation cultivation of fast-growing willows and plantations of Betula pendula, Roth on Hirvineva, a mire formerly used for peat production, in Liminka, Finland. Nopeakasvuisten pajujen (Salix spp. ) lyhytkiertoviljelystae ja rauduskoivun (Betula pendula) viljelystae turvetuotannosta poistuneella suolla, limingan Hirvinevalla

Energy Technology Data Exchange (ETDEWEB)

Lumme, I.; Kiukaanniemi, E.

1987-01-01

This report is concerned with afforestation experiments using fast-growing willows (Salix spp.) and silver birch (Betula pendula, Roth) conducted by the Northern Finland Research Institute of the University of Oulu at the site of a mire formerly used for peat production, Hirvineva in the commune of Liminka (62 deg C 45{sup '} N, 23 deg C 30{sup '} E). Experiments were carried out at the early stages of willow cultivation into the use of chemical fertilizers and peat ash, the liming requirement of the soil and the effects of tilling of the soil on growth. Since 1985 efforts have been concentrated on developing new willow clones. Research was also begun into the mycorhiza which develop when willows are cultivated on peat soils. The experiments with Betula pendula were devoted to examining the effects of plantation density and fertilization with peat ash on four-year old saplings.

Reliability demonstration of imaging surveillance systems

International Nuclear Information System (INIS)

Sheridan, T.F.; Henderson, J.T.; MacDiarmid, P.R.

1979-01-01

Security surveillance systems which employ closed circuit television are being deployed with increasing frequency for the protection of property and other valuable assets. A need exists to demonstrate the reliability of such systems before their installation to assure that the deployed systems will operate when needed with only the scheduled amount of maintenance and support costs. An approach to the reliability demonstration of imaging surveillance systems which employ closed circuit television is described. Failure definitions based on industry television standards and imaging alarm assessment criteria for surveillance systems are discussed. Test methods which allow 24 hour a day operation without the need for numerous test scenarios, test personnel and elaborate test facilities are presented. Existing reliability demonstration standards are shown to apply which obviate the need for elaborate statistical tests. The demonstration methods employed are shown to have applications in other types of imaging surveillance systems besides closed circuit television

Hydroponic screening for metal resistance and accumulation of cadmium and zinc in twenty clones of willows and poplars

International Nuclear Information System (INIS)

Santos Utmazian, Maria Noel dos; Wieshammer, Gerlinde; Vega, Rosa; Wenzel, Walter W.

2007-01-01

We screened 20 different clones of willow and poplar species in hydroponic experiments for their metal resistance and accumulation properties. Plants were exposed for 4 weeks either to single additions of (μM) 4.45 Cd or 76.5 Zn, or a metal cocktail containing the same amounts of Cd and Zn along with 7.87 Cu and 24.1 Pb. Plant biomass, metal tolerance and metal accumulation pattern in roots and leaves varied greatly between clones. The leaf:root ratio of metal concentrations was clearly underestimated compared to soil experiments. The largest metal concentrations in leaves were detected in Salix dasyclados (315 mg Cd kg -1 d.m.) and a Salix smithiana clone (3180 mg Zn kg -1 d.m.) but these species showed low metal tolerance. In spite of smaller Cd and Zn concentrations, the metal-tolerant clones Salix matsudana, Salix fragilis-1, and Salix purpurea-1 hold promise for phytoextraction as they produced large biomass and metal contents in leaves. - Hydroponically grown willows and poplar clones accumulate up to (mg kg -1 d.w.) 315 Cd and 3180 Zn in leaves

Hydroponic screening for metal resistance and accumulation of cadmium and zinc in twenty clones of willows and poplars

Energy Technology Data Exchange (ETDEWEB)

Santos Utmazian, Maria Noel dos [Department of Forest- and Soil Sciences, University of Natural Resources and Applied Life Sciences, Vienna, Peter-Jordan-Strasse 82, A-1190 Vienna (Austria); Wieshammer, Gerlinde [Department of Forest- and Soil Sciences, University of Natural Resources and Applied Life Sciences, Vienna, Peter-Jordan-Strasse 82, A-1190 Vienna (Austria); Vega, Rosa [Department of Forest- and Soil Sciences, University of Natural Resources and Applied Life Sciences, Vienna, Peter-Jordan-Strasse 82, A-1190 Vienna (Austria); Wenzel, Walter W. [Department of Forest- and Soil Sciences, University of Natural Resources and Applied Life Sciences, Vienna, Peter-Jordan-Strasse 82, A-1190 Vienna (Austria)]. E-mail: walter.wenzel@boku.ac.at

2007-07-15

We screened 20 different clones of willow and poplar species in hydroponic experiments for their metal resistance and accumulation properties. Plants were exposed for 4 weeks either to single additions of ({mu}M) 4.45 Cd or 76.5 Zn, or a metal cocktail containing the same amounts of Cd and Zn along with 7.87 Cu and 24.1 Pb. Plant biomass, metal tolerance and metal accumulation pattern in roots and leaves varied greatly between clones. The leaf:root ratio of metal concentrations was clearly underestimated compared to soil experiments. The largest metal concentrations in leaves were detected in Salix dasyclados (315 mg Cd kg{sup -1} d.m.) and a Salix smithiana clone (3180 mg Zn kg{sup -1} d.m.) but these species showed low metal tolerance. In spite of smaller Cd and Zn concentrations, the metal-tolerant clones Salix matsudana, Salix fragilis-1, and Salix purpurea-1 hold promise for phytoextraction as they produced large biomass and metal contents in leaves. - Hydroponically grown willows and poplar clones accumulate up to (mg kg{sup -1} d.w.) 315 Cd and 3180 Zn in leaves.

Biomass power for rural development. Technical progress report, Phase 2, July 1--September 30, 1998

Energy Technology Data Exchange (ETDEWEB)

Neuhauser, E.

1999-01-01

The project undertaken by the Salix Consortium is a multi-phased, multi-partner endeavor. Phase 1 focused on initial development and testing of the technology and forging the necessary agreements to demonstrate commercial willow production. The Phase 1 objectives have been successfully completed: preparing final design plans for two utility pulverized coal boiler for 20 MW of biopower capacity; developing fuel supply plans for the project with a goal of establishing 365 ha (900 ac) of willow; obtaining power production commitments from the power companies for Phase 2; obtaining construction and environmental permits; and developing an experimental strategy for crop production and power generation improvements needed to assure commercial success. The R and D effort also addresses environmental issues pertaining to introduction of the willow energy system. Beyond those Phase 1 requirements, the Consortium has already successfully demonstrated cofiring at Greenidge Station and has initiated development of the required nursery capacity for acreage scale-up. In Phase 2 every aspect of willow production and power generation from willow biomass will be demonstrated. The ultimate objective of Phase 2 is to transition the work performed under the Biomass Power for Rural Development project into a thriving, self-supported energy crop enterprise.

The effect of water availability on stand-level productivity, transpiration, water use efficiency and radiation use efficiency of field-grown willow clones

DEFF Research Database (Denmark)

Linderson, Maj-Lena; Iritz, Z.; Lindroth, A.

2007-01-01

The effect of water availability on stand-level productivity, transpiration, water use efficiency (WUE) and radiation use efficiency (RUE) is evaluated for different willow clones at stand level. The measurements were made during the growing season 2000 in a 3-year-old plantation in Scania......, southernmost Sweden. Six willow clones were included in the study: L78183, SW Rapp, SW Jorunn, SW Jorr, SW Tora and SW Loden. All clones were exposed to two water treatments: rain-fed, non-irrigated treatment and reduced water availability by reduced soil water recharge. Field measurements of stem sap...... low compared to other results. Generally, all clones, except for Jorunn, seem to be better off concerning biomass production, WUE and RUE than the reference clone. Jorr, Jorunn and Loden also seem to be able to cope with the reduced water availability with increase in the water use efficiency. Tora...

Orbital Express fluid transfer demonstration system

Science.gov (United States)

Rotenberger, Scott; SooHoo, David; Abraham, Gabriel

2008-04-01

Propellant resupply of orbiting spacecraft is no longer in the realm of high risk development. The recently concluded Orbital Express (OE) mission included a fluid transfer demonstration that operated the hardware and control logic in space, bringing the Technology Readiness Level to a solid TRL 7 (demonstration of a system prototype in an operational environment). Orbital Express (funded by the Defense Advanced Research Projects Agency, DARPA) was launched aboard an Atlas-V rocket on March 9th, 2007. The mission had the objective of demonstrating technologies needed for routine servicing of spacecraft, namely autonomous rendezvous and docking, propellant resupply, and orbital replacement unit transfer. The demonstration system used two spacecraft. A servicing vehicle (ASTRO) performed multiple dockings with the client (NextSat) spacecraft, and performed a variety of propellant transfers in addition to exchanges of a battery and computer. The fluid transfer and propulsion system onboard ASTRO, in addition to providing the six degree-of-freedom (6 DOF) thruster system for rendezvous and docking, demonstrated autonomous transfer of monopropellant hydrazine to or from the NextSat spacecraft 15 times while on orbit. The fluid transfer system aboard the NextSat vehicle was designed to simulate a variety of client systems, including both blowdown pressurization and pressure regulated propulsion systems. The fluid transfer demonstrations started with a low level of autonomy, where ground controllers were allowed to review the status of the demonstration at numerous points before authorizing the next steps to be performed. The final transfers were performed at a full autonomy level where the ground authorized the start of a transfer sequence and then monitored data as the transfer proceeded. The major steps of a fluid transfer included the following: mate of the coupling, leak check of the coupling, venting of the coupling, priming of the coupling, fluid transfer, gauging

The influence of electrical charge and indolebutyric acid on rooting of willow cuttings

Directory of Open Access Journals (Sweden)

R. Domański

2015-06-01

Full Text Available Willow cuttings were treated by direct electrical current (DEC, with a negative or a positive electrode inserted inside them, and with the other being outside. Both directions of DEC flow between electrodes stimulated rooting as actively as growth stimulators. The mung bean or oat coleoptile straight growth test showed that the cuttings released some growth promoters into the surrounding water. However, the simultaneous release of some undetected rooting inhibitors was not excluded. The experiment, shows the possibility of changing the chemical regulatory mechanisms of tissues by the use of weak, direct electrical current which causes, the migration of particular substance{s into or from a definite tissue or organ.

Phytoremediation of Metal Contaminated Soil Using Willow: Exploiting Plant-Associated Bacteria to Improve Biomass Production and Metal Uptake.

Science.gov (United States)

Janssen, Jolien; Weyens, Nele; Croes, Sarah; Beckers, Bram; Meiresonne, Linda; Van Peteghem, Pierre; Carleer, Robert; Vangronsveld, Jaco

2015-01-01

Short rotation coppice (SRC) of willow and poplar is proposed for economic valorization and concurrently as remediation strategy for metal contaminated land in northeast-Belgium. However, metal phytoextraction appears insufficient to effectuate rapid reduction of soil metal contents. To increase both biomass production and metal accumulation of SRC, two strategies are proposed: (i) in situ selection of the best performing clones and (ii) bioaugmentation of these clones with beneficial plant-associated bacteria. Based on field data, two experimental willow clones, a Salix viminalis and a Salix alba x alba clone, were selected. Compared to the best performing commercial clones, considerable increases in stem metal extraction were achieved (up to 74% for Cd and 91% for Zn). From the selected clones, plant-associated bacteria were isolated and identified. All strains were subsequently screened for their plant growth-promoting and metal uptake enhancing traits. Five strains were selected for a greenhouse inoculation experiment with the selected clones planted in Cd-Zn-Pb contaminated soil. Extraction potential tended to increase after inoculation of S. viminalis plants with a Rahnella sp. strain due to a significantly increased twig biomass. However, although bacterial strains showing beneficial traits in vitro were used for inoculation, increments in extraction potential were not always observed.

Structural and productive-developmental characteristics of white willow plantations of different density on humogley in Donji Srem

Directory of Open Access Journals (Sweden)

Andrašev Siniša

2012-01-01

Full Text Available The study was conducted in two plantations of white willow (Salix alba L. in Donji Srem on the humogley soil type (hydromorphic black soil, which belongs to a narrow-leaved ash forest with remote sedge (Carici remotae - Fraxinetum angustifoliae Jov. et Tom., 1979. The plantations are located in the same depression. The SP (sample plot-1 plantation is 21 years old with a 6×6 m planting spacing, and the SP-2 plantation is 27 years old with a 3×3m planting spacing. Elements of stem growth in the SP-1 plantation showed that with the white willow planting spacing of 6×6 m and a planned 25-year production cycle it is possible to obtain about 250 m3•ha-1 of timber volume, with an 80% net share of technical wood and a 20 % share of pulp wood. The plantation in SP-2 is at the age, which is well above the optimum age in terms of rational management, and the total volume at the age of 27 years is about 300 m3•ha-1, with a 53.7% net share of technical wood and a 46.3% share of pulpwood. [Projekat Ministarstva nauke Republike Srbije, br. 43007: Istraživanje klimatskih promena na životnu sredinu: praćenje uticaja, adaptacija i ublažavanje

Harvest and logistics for better profitability from small cultivations of Short Rotation Willow Coppice; Skoerdeteknik och logistik foer baettre loensamhet fraan smaa odlingar av Salix

Energy Technology Data Exchange (ETDEWEB)

Baky, Andras; Forsberg, Maya; Rosenqvist, Haakan; Jonsson, Nils; Sundberg, Martin

2010-06-15

In Sweden, the political desire to increase the amount of short rotation willow coppice (Salix) plantations has been expressed. However, for various reasons interest from farmers has been low. The hypothesis of this study is that the total area of Salix cultivation can be increased by also cultivating fields smaller than those generally considered economic today. In order to lower production costs, machine systems adapted for harvest of smaller fields are required. The possibility of using farmers' existing tractors and more convenient machines, as well as achieving lower machine costs for smaller fields, may increase farmers' interest. The long-term objective is to achieve large-scale deliveries of willow with small-scale solutions at farm level, as an option and complement to today's more large-scale systems for harvesting willow. Costs, energy use and climatic impact (CO{sub 2} emissions) for two harvest and logistical chains suitable for small fields have been calculated from field to energy plant, and methods for minimizing these costs have been analyzed. Comparison is made with the direct chipping system, the most commonly used in Sweden today. The systems studied comprised: 1. Direct bundling harvest system with a tractor-towed harvester, collection of bundles in the field with a trailer-mounted crane, and storage in a pile before delivery. Chipping is performed at the energy plant. 2. Direct billeting with a tractor-towed harvester accompanied simultaneously by a tractor and trailer for collection, and storage in a pile before delivery. 3. Direct chipping with a self-propelled modified forage harvester accompanied simultaneously by a tractor and container for collection, and direct delivery to plant. Both the billet and bundle systems show higher costs than the direct chipping system, irrespective of field size. The analysis of different scenarios and conditions shows possibilities of lowering the costs through certain measures. Furthermore

Nutrient enhanced short rotation coppice for biomass in central Wales

Energy Technology Data Exchange (ETDEWEB)

Hodson, R.W.; Slater, F.M.; Lynn, S.F.; Randerson, P.F. [Univ. of Wales (United Kingdom)

1993-12-31

Two projects involving short rotation willow coppice are taking place on the eastern side of the Cambrian Mountains in central Wales. One project examines, as an alternative land use, the potential of short rotation willow coppice variously enhanced by combinations of lime, phosphorous and potassium fertilizers and also digested sewage sludge on an acidic upland site at an altitude of 260m. The first year results of this project are described in detail, showing the necessity for limestone additions and also demonstrating that of the four willow varieties established, Salix dasyclados is the only possible, profitable fuel crop. The other project involving willow in a filter bed system is outlined along with an additional project investigating the effect of sewage sludge additions on the Rubus fruticosus production in a birch dominated mixed deciduous woodland.

The effect of water availability on stand-level productivity, transpiration, water use efficiency and radiation use efficiency of field-grown willow clones

International Nuclear Information System (INIS)

Linderson, Maj-Lena; Iritz, Zinaida; Lindroth, Anders

2007-01-01

The effect of water availability on stand-level productivity, transpiration, water use efficiency (WUE) and radiation use efficiency (RUE) is evaluated for different willow clones at stand level. The measurements were made during the growing season 2000 in a 3-year-old plantation in Scania, southernmost Sweden. Six willow clones were included in the study: L78183, SW Rapp, SW Jorunn, SW Jorr, SW Tora and SW Loden. All clones were exposed to two water treatments: rain-fed, non-irrigated treatment and reduced water availability by reduced soil water recharge. Field measurements of stem sap-flow and biometry are up-scaled to stand transpiration and stand dry substance production and used to assess WUE. RUE is estimated from the ratio between the stand dry substance production and the accumulated absorbed photosynthetic active radiation over the growing season. The total stand transpiration rate for the 5 months lies between 100 and 325 mm, which is fairly low compared to the Penman-Monteith transpiration for willow, reaching 400-450 mm for the same period. Mean WUE of all clones and treatments is 5.3 g/kg, which is high compared to earlier studies, while average RUE is 0.31 g/mol, which is slightly low compared to other results. Generally, all clones, except for Jorunn, seem to be better off concerning biomass production, WUE and RUE than the reference clone. Jorr, Jorunn and Loden also seem to be able to cope with the reduced water availability with increase in the water use efficiency. Tora performs significantly better than the other clones concerning both growth and efficiency in light and water use, but the effect of the dry treatment on stem growth shows sensitivity to water availability. The reduced stem growth could be due to a change in allocation patterns

AVNG system demonstration

Energy Technology Data Exchange (ETDEWEB)

Thron, Jonathan Louis [Los Alamos National Laboratory; Mac Arthur, Duncan W [Los Alamos National Laboratory; Kondratov, Sergey [VNIIEF; Livke, Alexander [VNIIEF; Razinkov, Sergey [VNIIEF

2010-01-01

An attribute measurement system (AMS) measures a number of unclassified attributes of potentially classified material. By only displaying these unclassified results as red or green lights, the AMS protects potentially classified information while still generating confidence in the measurement result. The AVNG implementation that we describe is an AMS built by RFNC - VNIIEF in Sarov, Russia. To provide additional confidence, the AVNG was designed with two modes of operation. In the secure mode, potentially classified measurements can be made with only the simple red light/green light display. In the open mode, known unclassified material can be measured with complete display of the information collected from the radiation detectors. The AVNG demonstration, which occurred in Sarov, Russia in June 2009 for a joint US/Russian audience, included exercising both modes of AVNG operation using a number of multi-kg plutonium sources. In addition to describing the demonstration, we will show photographs and/or video taken of AVNG operation.

Transportable Vitrification System Demonstration on Mixed Waste

International Nuclear Information System (INIS)

Zamecnik, J.R.; Whitehouse, J.C.; Wilson, C.N.; Van Ryn, F.R.

1998-01-01

This paper describes preliminary results from the first demonstration of the Transportable Vitrification System (TVS) on actual mixed waste. The TVS is a fully integrated, transportable system for the treatment of mixed and low-level radioactive wastes. The demonstration was conducted at Oak Ridge's East Tennessee Technology Park (ETTP), formerly known as the K-25 site. The purpose of the demonstration was to show that mixed wastes could be vitrified safely on a 'field' scale using joule-heated melter technology and obtain information on system performance, waste form durability, air emissions, and costs

100-N Area Strontium-90 Treatability Demonstration Project: Phytoextraction Along the 100-N Columbia River Riparian Zone – Field Treatability Study

Energy Technology Data Exchange (ETDEWEB)

Fellows, Robert J.; Fruchter, Jonathan S.; Driver, Crystal J.; Ainsworth, Calvin C.

2010-01-11

Strontium-90 (90Sr) is present both in the aquifer near the river and in the vadose and riparian zones of the river’s shore at 100-NR-2. Phytoextraction of 90Sr is being considered as a potential remediation system along the riparian zone of the Columbia River. Phytoextraction would employ coyote willow (Salix exigua). Past studies have shown that willow roots share uptake mechanisms for Sr with Ca, a plant macronutrient as well as no discrimination between Sr and 90Sr. Willow 90Sr concentration ratios [CR’s; (pCi 90Sr/g dry wt. of new growth tissue)/(pCi 90Sr/g soil porewater)] were consistently greater than 65 with three-quarters of the assimilated label partitioned into the above ground shoot. Insect herbivore experiments also demonstrated no significant potential for bioaccumulation or food chain transfer from their natural activities. The objectives of this field study were three-fold: (1) to demonstrate that a viable, “managed” plot of coyote willows can be established on the shoreline of the Columbia River that would survive the same microenvironment to be encountered at the 100-NR-2 shoreline; (2) to show through engineered barriers that large and small animal herbivores can be prevented from feeding on these plants; and (3) to show that once established, the plants will provide sufficient biomass annually to support the phytoextraction technology. A field treatability demonstration plot was established on the Columbia River shoreline alongside the 100-K West water intake at the end of January 2007. The plot was delimited by a 3.05 m high chain-link fence and was approximately 10 x 25 m in size. A layer of fine mesh metal small animal screening was placed around the plot at the base of the fencing to a depth of 45 cm. A total of sixty plants were placed in six slightly staggered rows with 1-m spacing between plants. The actual plot size was 0.00461 hectare (ha). At the time of planting (March 12, 2007), the plot was located about 10 m from the

Fungal community structure under goat willows (Salix caprea L.) growing at metal polluted site: the potential of screening in a model phytostabilisation study

Science.gov (United States)

Marjana Regvar; Matevz Likar; Andrej Piltaver; Nives Kugonic; Jane E. Smith

2010-01-01

Goat willow (Salix caprea L.) was selected in a previous vegetation screening study as a potential candidate for the later-stage phytostabilisation efforts at a heavily metal polluted site in Slovenia. The aims of this study were to identify the fungi colonising roots of S. caprea along the gradient of vegetation succession and...

Exploration Medical System Demonstration

Science.gov (United States)

Rubin, D. A.; Watkins, S. D.

2014-01-01

BACKGROUND: Exploration class missions will present significant new challenges and hazards to the health of the astronauts. Regardless of the intended destination, beyond low Earth orbit a greater degree of crew autonomy will be required to diagnose medical conditions, develop treatment plans, and implement procedures due to limited communications with ground-based personnel. SCOPE: The Exploration Medical System Demonstration (EMSD) project will act as a test bed on the International Space Station (ISS) to demonstrate to crew and ground personnel that an end-to-end medical system can assist clinician and non-clinician crew members in optimizing medical care delivery and data management during an exploration mission. Challenges facing exploration mission medical care include limited resources, inability to evacuate to Earth during many mission phases, and potential rendering of medical care by non-clinicians. This system demonstrates the integration of medical devices and informatics tools for managing evidence and decision making and can be designed to assist crewmembers in nominal, non-emergent situations and in emergent situations when they may be suffering from performance decrements due to environmental, physiological or other factors. PROJECT OBJECTIVES: The objectives of the EMSD project are to: a. Reduce or eliminate the time required of an on-orbit crew and ground personnel to access, transfer, and manipulate medical data. b. Demonstrate that the on-orbit crew has the ability to access medical data/information via an intuitive and crew-friendly solution to aid in the treatment of a medical condition. c. Develop a common data management framework that can be ubiquitously used to automate repetitive data collection, management, and communications tasks for all activities pertaining to crew health and life sciences. d. Ensure crew access to medical data during periods of restricted ground communication. e. Develop a common data management framework that

21st Session of the International Poplar Commission (IPC-2000): poplar and willow culture: meeting the needs of society and the environment; 200 September 24-28; Vancouver, WA.

Science.gov (United States)

J.G. Isebrands; J. Richardson

2000-01-01

Research results and ongoing research activities on poplar and willow breeding, diseases, insects, production, and utilization are described in 220 abstracts from the International Poplar Commission meeting in Vancouver, Washington, September 24-28, 2000.

Radioactive waste incineration system cold demonstration test

Energy Technology Data Exchange (ETDEWEB)

Hozumi, Masahiro; Takaoku, Yoshinobu; Koyama, Shigeru; Nagae, Madoka; Seike, Yasuhiko; Yamanaka, Yasuhiro; Shibata, Kenji; Manabe, Kyoichi

1984-12-01

To demonstrate Waste Incineration System (WIS) which our company has been licensed by Combustion Engineering Inc., USA we installed a demonstration test plant in our Hiratsuka Research Laboratory and started the demonstration test on January 1984. One of the characteristics of this system is to be able to process many kinds of wastes with only one system, and to get high volume reduction factors. In our test plant, we processed paper, cloth, wood, polyethylene sheets as the samples of solid combustible wastes and spent ion exchange resins with incineration and processed condensed liquid wastes with spray drying. We have got good performances and enough Decontamination Factor (DF) data for the dust control equipment. In this paper, we introduce this demonstration test plant and report the test results up to date. (author).

Phytoremediation potential of poplar and willow species in small scale constructed wetland for boron removal.

Science.gov (United States)

Yıldırım, Kubilay; Kasım, Gözde Çıtır

2018-03-01

Boron (B) pollution is an expanding environmental problem throughout the world due to intensive mining practices and extensive usage of B in agricultural chemicals and industrial products in recent years. The purpose of this study was to investigate B removal performance of four poplar and four willow species in small scale Constructed Wetland (CW). Rooted cuttings of tested species were treated with simulated wastewater having five elevated B concentrations (0.5, 5, 10, 20 and 40 ppm). All the tested species could resist up to 20 ppm wastewater B supply and could regrow from their roots in the soil having maximum 15 mg/kg B content. The result of the study indicated that 65% ± 5.3 of B was removed from the wastewater in 5 ppm B treatment while the same efficiency decreased to 45% ± 4.6 at 40 ppm B supply. The average effect of sediment on B removal was found to be approximately 20% for all B treatments while the remaining part of the loaded B was removed from the CW within effluent (35-54%). Therefore, actual effects of plant species on B removal was ranged from 45% to 25% between 5 and 40 ppm B treatments. Mass B removal within plant body (phytextraction) comprised the 13-10% of total loaded B in CW while the remaining part of the loaded B (31-15%) was stabilized into the sediment with the effects of poplar and willow roots. These results presented clear understanding of effective B purification mechanisms in CWs. Boron phytextraction capacity of a plant species was less effective than its phytstabilization efficiency which increase filtering capacity of the sediment and stabilization of more B around the rhizosphere. In terms of their B removal ability, P.nigra and S.anatolica had the highest B removal capacities with phytextraction (20-11%) while S.alba, P.alba and S.babylonica had more phytstabilizaiton performance (40-15%) in CW. Disposal of B loaded plant material create another environmental costs for CW applications. Therefore, B loaded

Demonstration of Eastman Christensen horizontal drilling system -- Integrated Demonstration Site, Savannah River Site

International Nuclear Information System (INIS)

1992-12-01

An innovative horizontal drilling system was used to install two horizontal wells as part of an integrated demonstration project at the Savannah River Site (SRS), Aiken, South Carolina. The SRS is located in south-central South Carolina in the upper Coastal Plain physiographic province. The demonstration site is located near the A/M Area, and is currently known as the Integated Demonstration Site. The Department of Energy's Office of Technology Development initiated an integrated demonstration of innovative technologies for cleanup of volatile organic compounds (VOCS) in soils and groundwater at the SRS in 1989. The overall goal of the program is to demonstrate, at a single location, multiple technologies in the fields of drilling, characterization, monitoring, and remediation. Innovative technologies are compared to one another and to baseline technologies in terms of technical performance and cost effectiveness. Transfer of successfully demonstrated technologies and systems to DOE environmental restoration organizations, to other government agencies, and to industry is a critical part of the program

Biomass power for rural development: Phase 2. Technical progress report, April 1--June 30, 1998

Energy Technology Data Exchange (ETDEWEB)

Neuhauser, E.

1998-11-01

The project undertaken by the Salix Consortium is a multi-phased, multi-partner endeavor. Phase-1 focused on initial development and testing of the technology and agreements necessary to demonstrate commercial willow production in Phase-2. The Phase-1 objectives have been successfully completed: preparing final design plans for two utility pulverized coal boilers, developing fuel supply plans for the project, obtaining power production commitments from the power companies for Phase-2, obtaining construction and environmental permits, and developing an experimental strategy for crop production and power generation improvements needed to assure commercial success. The R and D effort also addresses environmental issues pertaining to introduction of the willow energy system. Beyond those Phase-1 requirements the Consortium has already successfully demonstrated cofiring at Greenidge Station and developed the required nursery capacity for acreage scale-up. This past summer 105 acres were prepared in advance for the spring planting in 1998. Having completed the above tasks, the Consortium is well positioned to begin Phase-2. In phase-2 every aspect of willow production and power generation from willow will be demonstrated. The ultimate objective of Phase-2 is to transition the work performed under the Rural Energy for the Future project into a thriving, self-supported energy crop enterprise.

System design specification Brayton Isotope Power System (BIPS) Flight System (FS), and Ground Demonstration System (GDS)

International Nuclear Information System (INIS)

1976-01-01

The system design specification for ground demonstration, development, and flight qualification of a Brayton Isotope Power System (BIPS) is presented. The requirements for both a BIPS conceptual Flight System (FS) and a Ground Demonstration System (GDS) are defined

Organic Carbon Accumulation in Topsoil Following Afforestation with Willow: Emphasis on Leaf Litter Decomposition and Soil Organic Matter Quality

Directory of Open Access Journals (Sweden)

Benoit Lafleur

2015-03-01

Full Text Available Short-rotation intensive cultures (SRICs of willows can potentially sequester carbon (C in soil. However, there is limited information regarding the factors governing soil organic C (Corg accumulation following afforestation. The objectives of this study were to: (i determine whether willow leads to Corg accumulation in the topsoil (0–10 cm two to six years after establishment in five SRICs located along a large climatic/productivity gradient in southern Quebec, and (ii assess the influence of leaf litter decomposition and soil organic matter (OM quality on Corg accumulation in the topsoil. Topsoil Corg concentrations and pools under SRICs were, on average, 25% greater than reference fields, and alkyls concentrations were higher under SRICs. On an annualized basis, Corg accumulation rates in the topsoil varied between 0.4 and 4.5 Mg ha−1 yr−1. Estimated annual litterfall C fluxes were in the same order of magnitude, suggesting that SRICs can accumulate Corg in the topsoil during early years due to high growth rates. Leaf litter decomposition was also related to Corg accumulation rates in the topsoil. It was positively correlated to growing season length, degree-days, and growing season average air and topsoil temperature (r > 0.70, and negatively correlated to topsoil volumetric water content (r = −0.55. Leaf litter decomposition likely occurred more quickly than that of plants in reference fields, and as it progressed, OM became more decay resistant, more stable and accumulated as Corg in the topsoil.

Biomass power for rural development. Technical progress report Phase-II. Contractual reporting period October-December 1999

Energy Technology Data Exchange (ETDEWEB)

Neuhauser, Edward; The Salix Consortium

2000-03-23

The project undertaken by the Salix Consortium is a multi-phased, multi-partner endeavor. Phase 1 focused on initial development and testing of the technology and forging the necessary agreements to demonstrate commercial willow production. The Phase 1 objectives have been successfully completed: preparing design plans for 2 utility pulverized coal boilers for 20 MW of biopower capacity; developing fuel supply plans for the project with a goal of establishing 365 ha (900 ac) of willow; obtaining power production commitments from the power companies for Phase 2; obtaining construction and environmental permits; and developing an experimental strategy for crop production and power generation improvements needed to assure commercial success. The R and D effort also addresses environmental issues pertaining to introduction of the willow energy system.

Kilowatt Isotope Power System: component report for the Ground Demonstration System Accumulator

International Nuclear Information System (INIS)

Brainard, E.L.

1978-01-01

The Model Number ORC1A3A01 System Accumulator for the Kilowatt Isotope Power System was expulsion tested and demonstrated to be in compliance with the requirements of Sundstrand Explusion Test Procedure, TP 400. Test requirements of TP 400 were extracted from the Kilowatt Isotope Power System, Ground Demonstration System Test Plan

New Rust Disease of Korean Willow (Salix koreensis) Caused by Melampsora yezoensis, Unrecorded Pathogen in Korea.

Science.gov (United States)

Yun, Yeo Hong; Ahn, Geum Ran; Yoon, Seong Kwon; Kim, Hoo Hyun; Son, Seung Yeol; Kim, Seong Hwan

2016-12-01

During the growing season of 2015, leaf specimens with yellow rust spots were collected from Salix koreensis Andersson, known as Korean willow, in riverine areas in Cheonan, Korea. The fungus on S. koreensis was identified as the rust species, Melampsora yezoensis , based on the morphology of urediniospores observed by light and scanning electron microscopy, and the molecular properties of the internal transcribed spacer rDNA region. Pathogenicity tests confirmed that the urediniospores are the causal agent of the rust symptoms on the leaves and young stems of S. koreensis . Here, we report a new rust disease of S. koreensis caused by the rust fungus, M. yezoensis , a previously unrecorded rust pathogen in Korea.

Influence of flooding and metal immobilising soil amendments on availability of metals for willows and earthworms in calcareous dredged sediment-derived soils

Energy Technology Data Exchange (ETDEWEB)

Vandecasteele, Bart, E-mail: bart.vandecasteele@ilvo.vlaanderen.b [Institute for Agricultural and Fisheries Research (ILVO), Scientific Institute of the Flemish Government, Burg. Van Gansberghelaan 109, B-9820 Merelbeke (Belgium); Du Laing, Gijs [Ghent University, Department of Applied Analytical and Physical Chemistry, Coupure 653, B-9000 Ghent (Belgium); Lettens, Suzanna [Research Institute for Nature and Forest (INBO), Scientific Institute of the Flemish Government, Gaverstraat 4, B-9500 Geraardsbergen (Belgium); Jordaens, Kurt [Department of Biology, Evolutionary Biology Group, University of Antwerp, Groenenborgerlaan 171, B-2020 Antwerp (Belgium); Tack, Filip M.G. [Ghent University, Department of Applied Analytical and Physical Chemistry, Coupure 653, B-9000 Ghent (Belgium)

2010-06-15

Soil amendments previously shown to be effective in reducing metal bioavailability and/or mobility in calcareous metal-polluted soils were tested on a calcareous dredged sediment-derived soil with 26 mg Cd/kg dry soil, 2200 mg Cr/kg dry soil, 220 mg Pb/kg dry soil, and 3000 mg Zn/kg dry soil. The amendments were 5% modified aluminosilicate (AS), 10% w/w lignin, 1% w/w diammonium phosphate (DAP, (NH{sub 4}){sub 2}HPO{sub 4}), 1% w/w MnO, and 5% w/w CaSO{sub 4}. In an additional treatment, the contaminated soil was submerged. Endpoints were metal uptake in Salix cinerea and Lumbricus terrestris, and effect on oxidation-reduction potential (ORP) in submerged soils. Results illustrated that the selected soil amendments were not effective in reducing ecological risk to vegetation or soil inhabiting invertebrates, as metal uptake in willows and earthworms did not significantly decrease following their application. Flooding the polluted soil resulted in metal uptake in S. cinerea comparable with concentrations for an uncontaminated soil. - Some soil amendments resulted in higher metal uptake by earthworms and willows than when the polluted soil was not amended but submersion of the polluted soil resulted in reduced Cd and Zn uptake in Salix cinerea.

DESIGN OF SMALL AUTOMATION WORK CELL SYSTEM DEMONSTRATIONS

International Nuclear Information System (INIS)

TURNER, C.; PEHL, J.

2000-01-01

The introduction of automation systems into many of the facilities dealing with the production, use and disposition of nuclear materials has been an ongoing objective. Many previous attempts have been made, using a variety of monolithic and, in some cases, modular technologies. Many of these attempts were less than successful, owing to the difficulty of the problem, the lack of maturity of the technology, and over optimism about the capabilities of a particular system. Consequently, it is not surprising that suggestions that automation can reduce worker Occupational Radiation Exposure (ORE) levels are often met with skepticism and caution. The development of effective demonstrations of these technologies is of vital importance if automation is to become an acceptable option for nuclear material processing environments. The University of Texas Robotics Research Group (UTRRG) has been pursuing the development of technologies to support modular small automation systems (each of less than 5 degrees-of-freedom) and the design of those systems for more than two decades. Properly designed and implemented, these technologies have a potential to reduce the worker ORE associated with work in nuclear materials processing facilities. Successful development of systems for these applications requires the development of technologies that meet the requirements of the applications. These application requirements form a general set of rules that applicable technologies and approaches need to adhere to, but in and of themselves are generally insufficient for the design of a specific automation system. For the design of an appropriate system, the associated task specifications and relationships need to be defined. These task specifications also provide a means by which appropriate technology demonstrations can be defined. Based on the requirements and specifications of the operations of the Advanced Recovery and Integrated Extraction System (ARIES) pilot line at Los Alamos National

Demonstration Advanced Avionics System (DAAS) function description

Science.gov (United States)

Bailey, A. J.; Bailey, D. G.; Gaabo, R. J.; Lahn, T. G.; Larson, J. C.; Peterson, E. M.; Schuck, J. W.; Rodgers, D. L.; Wroblewski, K. A.

1982-01-01

The Demonstration Advanced Avionics System, DAAS, is an integrated avionics system utilizing microprocessor technologies, data busing, and shared displays for demonstrating the potential of these technologies in improving the safety and utility of general aviation operations in the late 1980's and beyond. Major hardware elements of the DAAS include a functionally distributed microcomputer complex, an integrated data control center, an electronic horizontal situation indicator, and a radio adaptor unit. All processing and display resources are interconnected by an IEEE-488 bus in order to enhance the overall system effectiveness, reliability, modularity and maintainability. A detail description of the DAAS architecture, the DAAS hardware, and the DAAS functions is presented. The system is designed for installation and flight test in a NASA Cessna 402-B aircraft.

Exploration Medical System Demonstration Project

Science.gov (United States)

Chin, D. A.; McGrath, T. L.; Reyna, B.; Watkins, S. D.

2011-01-01

A near-Earth Asteroid (NEA) mission will present significant new challenges including hazards to crew health created by exploring a beyond low earth orbit destination, traversing the terrain of asteroid surfaces, and the effects of variable gravity environments. Limited communications with ground-based personnel for diagnosis and consultation of medical events require increased crew autonomy when diagnosing conditions, creating treatment plans, and executing procedures. Scope: The Exploration Medical System Demonstration (EMSD) project will be a test bed on the International Space Station (ISS) to show an end-to-end medical system assisting the Crew Medical Officers (CMO) in optimizing medical care delivery and medical data management during a mission. NEA medical care challenges include resource and resupply constraints limiting the extent to which medical conditions can be treated, inability to evacuate to Earth during many mission phases, and rendering of medical care by a non-clinician. The system demonstrates the integration of medical technologies and medical informatics tools for managing evidence and decision making. Project Objectives: The objectives of the EMSD project are to: a) Reduce and possibly eliminate the time required for a crewmember and ground personnel to manage medical data from one application to another. b) Demonstrate crewmember's ability to access medical data/information via a software solution to assist/aid in the treatment of a medical condition. c) Develop a common data management architecture that can be ubiquitously used to automate repetitive data collection, management, and communications tasks for all crew health and life sciences activities. d) Develop a common data management architecture that allows for scalability, extensibility, and interoperability of data sources and data users. e) Lower total cost of ownership for development and sustainment of peripheral hardware and software that use EMSD for data management f) Provide

Carbon isotope variation in shrub willow (Salix spp.) ring-wood as an indicator of long-term water status, growth and survival

International Nuclear Information System (INIS)

Schifman, Laura A.; Stella, John C.; Volk, Timothy A.; Teece, Mark A.

2012-01-01

Quantifying interannual change in water status of woody plants using stable carbon isotopes provides insight on long-term plant ecophysiology and potential success in variable environments, including under-utilized agricultural land for biomass production and highly disturbed sites for phytoremediation applications. We analyzed δ 13 C values in annual ring-wood of four shrub willow varieties used for biomass production and phytoremediation at three sites in central New York State (U.S.A). We tested a cost-effective sampling method for estimating whole-shrub water status by comparing δ 13 C values of the plant’s largest stem against a composite sample of all stems. The largest stem showed 0.3‰ 13 C enrichment (range −0.7–1.1‰) compared to the whole-plant, making it a more sensitive indicator of water status than the composite sample. Growing season precipitation exerted a strong negative influence on wood tissue chemistry, with an average 0.26‰ 13 C depletion per 100 mm increase in precipitation. An average annual 0.28‰ 13 C enrichment was also observed with increased plant age; this pattern was consistent among all four willow varieties and across sites. Finally, increased 13 C enrichment in wood tissue was positively associated with plant size at the individual plant level, and associated negatively and more variably survival at the plot scale. These results have important implications for the design and management of biomass production and phytoremediation systems. Increased sensitivity of older plants suggests that longer rotations may experience growth limitations and/or lower survival in low-precipitation years, resulting in reduced yields of biomass crops and loss of effectiveness in phytoremediation applications. -- Highlights: ► A 0.26‰ 13 C depletion in wood tissue occurred per 100 mm increase in precipitation. ► There was an average 13 C enrichment with plant age and size for all varieties. ► Greater 13 C enrichment often lead to

Food habits of the southwestern willow flycatcher during the nesting season

Science.gov (United States)

Drost, Charles A.; Paxton, Eben H.; Sogge, Mark K.; Whitfield, Mary J.

2003-01-01

The food habits and prey base of the endangered Southwestern Willow Flycatcher (Empidonax traillii extimus) are not well known. We analyzed prey remains in 59 fecal samples from an intensively-studied population of this flycatcher at the Kern River Preserve in southern California. These samples were collected during the nesting season in 1996 and 1997 from adults caught in mist nets, and from nestlings temporarily removed from the nest for banding. A total of 379 prey individuals were identified in the samples. Dominant prey taxa, both in total numbers and in percent occurrence, were true bugs (Hemiptera), flies (Diptera), and beetles (Coleoptera). Leafhoppers (Homoptera: Cicadellidae), spiders (Araneae), bees and wasps (Hymenoptera), and dragonflies and damselflies (Odonata) were also common items. Diet composition was significantly different between years, due to a large difference in the numbers of spiders between 1996 and 1997. There was also a significant difference between the diet of young and adults, with the diet of young birds having significantly higher numbers of odonates and beetles. There was a trend toward diet differences between males and females, but this was not significant at the P = 0.05 level.

De novo transcriptome and small RNA analysis of two Chinese willow cultivars reveals stress response genes in Salix matsudana.

Directory of Open Access Journals (Sweden)

Guodong Rao

Full Text Available Salix matsudana Koidz. is a deciduous, rapidly growing, and drought resistant tree and is one of the most widely distributed and commonly cultivated willow species in China. Currently little transcriptomic and small RNAomic data are available to reveal the genes involve in the stress resistant in S. matsudana. Here, we report the RNA-seq analysis results of both transcriptome and small RNAome data using Illumina deep sequencing of shoot tips from two willow variants(Salix. matsudana and Salix matsudana Koidz. cultivar 'Tortuosa'. De novo gene assembly was used to generate the consensus transcriptome and small RNAome, which contained 106,403 unique transcripts with an average length of 944 bp and a total length of 100.45 MB, and 166 known miRNAs representing 35 miRNA families. Comparison of transcriptomes and small RNAomes combined with quantitative real-time PCR from the two Salix libraries revealed a total of 292 different expressed genes(DEGs and 36 different expressed miRNAs (DEMs. Among the DEGs and DEMs, 196 genes and 24 miRNAs were up regulated, 96 genes and 12 miRNA were down regulated in S. matsudana. Functional analysis of DEGs and miRNA targets showed that many genes were involved in stress resistance in S. matsudana. Our global gene expression profiling presents a comprehensive view of the transcriptome and small RNAome which provide valuable information and sequence resources for uncovering the stress response genes in S. matsudana. Moreover the transcriptome and small RNAome data provide a basis for future study of genetic resistance in Salix.

Willow clones with high biomass yield in short rotation coppice in the southern region of Tohoku district (Japan)

International Nuclear Information System (INIS)

Mitsui, Yu; Seto, Shoko; Nishio, Mari; Minato, Kazuya; Ishizawa, Kimiharu; Satoh, Shigeru

2010-01-01

The present study was conducted to select willow (Salix spp.) clones with a high potential for use as biomass energy crops in the southern region of Tohoku district in Japan. Cuttings of 8 willow clones were planted on an abandoned farmland near Sendai (av. annual temp., 10.9 o C) in March 2006, grown throughout the year and cut back in late December 2006 to resprout from the remaining stools in March 2007. The biomass yield in December 2007, after the first growing season, was highest in Salix pet-susu clone KKD, followed by Salix pseudolinearis clone FXM and Salix sachalinensis clone SEN. The biomass yield on December 2008, after the second growing season, was again highest in clone KKD followed by clone FXM, S. pet-susu clone HB471 and S. sachalinensis clone SEN; the average annual yield of dry mass after the second growing season being 3.09, 2.58, 2.17 and 1.85 kgDM plant -1 for the clones in this order. Plant growth form differed among the clones. Clones FXM and SEN had several shoots of almost uniform base diameter, whereas clones KKD and HB471 showed plagiotropic growth with one thick and several thin shoots. The calorific values of dried stem segments were similar among clones, ranging from 18.7 to 19.1 kJ g -1 . The dried stem segments contained 78.9-81.2 wt.% hollocellulose, 27.2-32.3 wt.% lignin and 2.1-4.0 wt.% extractives with ethanol-benzene, depending on clones. Based on these results, we could select four clones (KKD, FXM, HB471 and SEN) suitable for biomass production by SRWC in this area.

Effect of biomass pretreatment on the product distribution and composition resulting from the hydrothermal liquefaction of short rotation coppice willow

DEFF Research Database (Denmark)

Grigoras, Ionela; Stroe, Rodica-Elisabeta; Sintamarean, Iulia-Maria

2017-01-01

A major challenge for the implementation of hydrothermal liquefaction (HTL) as a continuous process is the formulation of lignocellulosic feedstock, which is prone to phase separation into water and biomass parts when pressurized. One approach to remedy such phase separation is to reduce the dry...... from the HTL of willow and proposes short rotation coppice as an alternative biomass feedstock for biofuels production. Alkaline–thermal pretreatment, besides making high dry matter pumpable feedstock slurries, also led to an increase in the production of the bio-crude product with an oxygen content...

The Management and Demonstration System at Murray State University.

Science.gov (United States)

Schroeder, Gary G.

The management system in use at the Murray State University Teacher Corps Project is described. The system uses management by objectives and the demonstration approach, and encourages managers to focus on the development and demonstration of ideas, processes, and structures. The system's operating concepts of time management and human resources…

Nutrient Concentrations of Bush Bean (Phaseolus vulgaris L. and Potato (Solanum tuberosum L. Cultivated in Subarctic Soils Managed with Intercropping and Willow (Salix spp. Agroforestry

Directory of Open Access Journals (Sweden)

Meaghan J. Wilton

2017-12-01

Full Text Available To ease food insecurities in northern Canada, some remote communities started gardening initiatives to gain more access to locally grown foods. Bush beans (Phaseolus vulgaris L. and potatoes (Solanum tuberosum L. were assessed for N, P, K, Mg, and Ca concentrations of foliage as indicators of plant nutrition in a calcareous silty loam soil of northern Ontario James Bay lowlands. Crops were grown in sole cropping and intercropping configurations, with comparisons made between an open field and an agroforestry site enclosed with willow (Salix spp. trees. Foliage chemical analysis of the sites revealed an abundance of Ca, adequacies for Mg and N, and deficiencies in P and K. Intercropping bean and potato did not show significant crop–crop facilitation for nutrients. The agroforestry site showed to be a superior management practice for the James Bay lowland region, specifically for P. The agroforestry site had significantly greater P for bean plant (p = 0.024 and potato foliage (p = 0.002 compared to the open site. It is suspected that the presence of willows improve plant available P to bean and potatoes by tree root—crop root interactions and microclimate enhancements.

X-Band CubeSat Communication System Demonstration

Science.gov (United States)

Altunc, Serhat; Kegege, Obadiah; Bundick, Steve; Shaw, Harry; Schaire, Scott; Bussey, George; Crum, Gary; Burke, Jacob C.; Palo, Scott; O'Conor, Darren

2015-01-01

Today's CubeSats mostly operate their communications at UHF- and S-band frequencies. UHF band is presently crowded, thus downlink communications are at lower data rates due to bandwidth limitations and are unreliable due to interference. This research presents an end-to-end robust, innovative, compact, efficient and low cost S-band uplink and X-band downlink CubeSat communication system demonstration between a balloon and a Near Earth Network (NEN) ground system. Since communication systems serve as umbilical cords for space missions, demonstration of this X-band communication system is critical for successfully supporting current and future CubeSat communication needs. This research has three main objectives. The first objective is to design, simulate, and test a CubeSat S- and X-band communication system. Satellite Tool Kit (STK) dynamic link budget calculations and HFSS Simulations and modeling results have been used to trade the merit of various designs for small satellite applications. S- and X-band antennas have been tested in the compact antenna test range at Goddard Space Flight Center (GSFC) to gather radiation pattern data. The second objective is simulate and test a CubeSat compatible X-band communication system at 12.5Mbps including S-band antennas, X-band antennas, Laboratory for Atmospheric and Space Physics (LASP) /GSFC transmitter and an S-band receiver from TRL-5 to TRL-8 by the end of this effort. Different X-band communication system components (antennas, diplexers, etc.) from GSFC, other NASA centers, universities, and private companies have been investigated and traded, and a complete component list for the communication system baseline has been developed by performing analytical and numerical analysis. This objective also includes running simulations and performing trades between different X-band antenna systems to optimize communication system performance. The final objective is to perform an end-to-end X-band CubeSat communication system

Connecting remote systems for demonstration of automation technologies

Science.gov (United States)

Brown, R. M.; Yee, R.

1988-01-01

An initial estimate of the communications requirements of the Systems Autonomy Demonstration Project (SADP) development and demonstration environments is presented. A proposed network paradigm is developed, and options for network topologies are explored.

The trigger card system for the MAJORANA DEMONSTRATOR

Science.gov (United States)

Thompson, William; Anderson, John; Howe, Mark; Meijer, Sam; Wilkerson, John; Majorana Collaboration

2014-09-01

The aim of the MAJORANA DEMONSTRATOR is to demonstrate the feasibility of providing low enough background levels to search for neutrinoless double-beta decay (0 νββ) in an array of germanium detectors enriched to 87% in 76Ge. Currently, it is unknown if this decay process occurs; however, observation of such a decay process would show that lepton number is violated, confirm that neutrinos are Majorana particles, and yield information on the absolute mass scale of the neutrino. With current experimental results indicating a half-life greater than 2 x 1025 years for this decay, the minimization of background events is of critical importance. Utilizing time correlation, coincidence testing is able to reject multi-detector events that may otherwise be mistaken for 0 νββ when viewed independently. Here, we present both the hardware and software of the trigger card system, which provides a common clock to all digitizers and the muon veto system, thereby enabling the rejection of background events through coincidence testing. Current experimental results demonstrate the accuracy of the distributed clock to be within two clock pulses (20 ns) across all system components. A test system is used to validate the data acquisition system. The aim of the MAJORANA DEMONSTRATOR is to demonstrate the feasibility of providing low enough background levels to search for neutrinoless double-beta decay (0 νββ) in an array of germanium detectors enriched to 87% in 76Ge. Currently, it is unknown if this decay process occurs; however, observation of such a decay process would show that lepton number is violated, confirm that neutrinos are Majorana particles, and yield information on the absolute mass scale of the neutrino. With current experimental results indicating a half-life greater than 2 x 1025 years for this decay, the minimization of background events is of critical importance. Utilizing time correlation, coincidence testing is able to reject multi-detector events that may

Eddy covariance N2O flux measurements at low flux rates: results from the InGOS campaign in a Danish willow field.

Science.gov (United States)

Ibrom, Andreas; Brümmer, Christian; Hensen, Arjan; van Asperen, Hella; Carter, Mette S.; Gasche, Rainer; Famulari, Daniela; Kutsch, Werner; Pilegaard, Kim; Ambus, Per

2014-05-01

Nitrous oxide (N2O) fluxes from soils are characterised by their high spatial and temporal variability. The fluxes depend on the availability of the substrates for nitrification and denitrification and soil physical and chemical conditions that control the metabolic microbial activity. The sporadic nature of the fluxes and their high sensitivity to alterations of the soil climate put very high demands on measurement approaches. Laser spectroscopy enables accurate and fast response detection of atmospheric N2O concentrations and is used for eddy covariance (EC) flux measurements. Alternatively N2O fluxes can be measured with chambers together with high precision analysers. Differences in the measurement approaches and system designs are expected to have a considerable influence on the accuracy of the flux estimation. This study investigates how three different eddy covariance systems perform in a situation of low N2O fluxes from a flat surface. Chamber flux measurements with differing chamber and analyser designs are used for comparison. In April 2013, the EU research infrastructure project InGOS (http://www.ingos-infrastructure.eu/) organised a campaign of N2O flux measurements in a willow plantation close to the Risø Campus of the Technical University of Denmark. The willow field was harvested in February 2013 and received mineral fertiliser equivalent to 120 kg N ha-1 before the campaign started. Three different eddy covariance systems took part in the campaign: two Aerodyne quantum cascade laser (QCL) based systems and one Los Gatos Research off-axis integrated-cavity-output spectroscopy (ICOS) system for N2O and CO. The sonic anemometers were all installed at 2 m height above the bare ground. Gill R3 type sonic anemometers were used with QCL systems and a Gil HS-50 with the ICOS system. The 10 Hz raw data were analysed with group specific softwares and procedures. The local conditions in the exceptionally cold and dry spring 2013 did not lead to large N2O flux

ELISA, a demonstrator environment for information systems architecture design

Science.gov (United States)

Panem, Chantal

1994-01-01

This paper describes an approach of reusability of software engineering technology in the area of ground space system design. System engineers have lots of needs similar to software developers: sharing of a common data base, capitalization of knowledge, definition of a common design process, communication between different technical domains. Moreover system designers need to simulate dynamically their system as early as possible. Software development environments, methods and tools now become operational and widely used. Their architecture is based on a unique object base, a set of common management services and they host a family of tools for each life cycle activity. In late '92, CNES decided to develop a demonstrative software environment supporting some system activities. The design of ground space data processing systems was chosen as the application domain. ELISA (Integrated Software Environment for Architectures Specification) was specified as a 'demonstrator', i.e. a sufficient basis for demonstrations, evaluation and future operational enhancements. A process with three phases was implemented: system requirements definition, design of system architectures models, and selection of physical architectures. Each phase is composed of several activities that can be performed in parallel, with the provision of Commercial Off the Shelves Tools. ELISA has been delivered to CNES in January 94, currently used for demonstrations and evaluations on real projects (e.g. SPOT4 Satellite Control Center). It is on the way of new evolutions.

A Catskill Flora and Economic Botany, III: Apetalae. Including the Poplars, Willows, Hickories, Birches, Beeches, Oaks, Elms, Nettles, Sorrels, Docks, and Smartweeds. Bulletin No. 443, New York State Museum.

Science.gov (United States)

Brooks, Karl L.

This compendium deals with the ecology and economic importance of the poplars, willows, hickories, birches, beeches, oaks, elms, nettles, sorrels, docks, and smartweeds growing in New York's Catskills. Provided are keys for identifying each plant to species by flowers, foliage, or winter buds. A line drawing accompanies a summary of basic data…

Large scale gas chromatographic demonstration system for hydrogen isotope separation

International Nuclear Information System (INIS)

Cheh, C.H.

1988-01-01

A large scale demonstration system was designed for a throughput of 3 mol/day equimolar mixture of H,D, and T. The demonstration system was assembled and an experimental program carried out. This project was funded by Kernforschungszentrum Karlsruhe, Canadian Fusion Fuel Technology Projects and Ontario Hydro Research Division. Several major design innovations were successfully implemented in the demonstration system and are discussed in detail. Many experiments were carried out in the demonstration system to study the performance of the system to separate hydrogen isotopes at high throughput. Various temperature programming schemes were tested, heart-cutting operation was evaluated, and very large (up to 138 NL/injection) samples were separated in the system. The results of the experiments showed that the specially designed column performed well as a chromatographic column and good separation could be achieved even when a 138 NL sample was injected

The WIPP transportation system: Demonstrated readiness

International Nuclear Information System (INIS)

Ward, T.R.; Spooner, R.

1991-01-01

The Department of Energy (DOE) has developed an integrated transportation system to transport transuranic (TRU) waste from ten widely-dispersed generator sites to the Waste Isolation Pilot Plant (WIPP). The system consists of a Type B container, a specially- designed trailer, a lightweight tractor, the DOE ''TRANSCOM'' vehicle tracking system, and uniquely qualified and highly-trained drivers. In June of 1989, the National Academy of Sciences reviewed the transportation system and concluded that: ''The system proposed for transportation of TRU waste to WIPP is safer than that employed for any other hazardous material in the United States today and will reduce risk to very low levels'' (emphasis added). The next challenge facing the DOE was demonstrating that this system was ready to transport the TRU waste to the WIPP site efficiently and in the safest manner possible. Not only did the DOE feel that is was necessary to convince itself that the system was safe, but also representatives of the 20 states through which it would travel

The WIPP transportation system: Demonstrated readiness

International Nuclear Information System (INIS)

Ward, T.R.; Spooner, R.

1991-01-01

The Department of Energy (DOE) has developed an integrated transportation system to transport transuranic (TRU) waste from ten widely-dispersed generator sites to the Waste Isolation Pilot Plant (WIPP). The system consists of a Type B container, a specially-designed trailer, a lightweight tractor, the DOE ''TRANSCOM'' vehicle tracing system, and uniquely qualified and highly-trained drivers. In June of 1989, the National Academy of Sciences reviewed the transportation system and concluded that: ''The system proposed for transportation of TRU waste to WIPP is safer than that employed for any other hazardous material in the United States today and will reduce risk to very low levels.'' The next challenge facing the DOE was demonstrating that this system was ready to transport the TRU waste to the WIPP site in the safest manner possible. Not only did the DOE feel that it was necessary to convince itself that the system was safe, but also representatives of the 23 states through which it traveled

Nuclear Systems (NS): Technology Demonstration Unit (TDU)

Data.gov (United States)

National Aeronautics and Space Administration — The Nuclear Systems Project demonstrates nuclear power technology readiness to support the goals of NASA's Space Technology Mission Directorate. To this end, the...

Variable acuity remote viewing system flight demonstration

Science.gov (United States)

Fisher, R. W.

1983-01-01

The Variable Acuity Remote Viewing System (VARVS), originally developed under contract to the Navy (ONR) as a laboratory brassboard, was modified for flight demonstration. The VARVS system was originally conceived as a technique which could circumvent the acuity/field of view/bandwidth tradeoffs that exists in remote viewing to provide a nearly eye limited display in both field of view (160 deg) and resolution (2 min arc) while utilizing conventional TV sensing, transmission, and display equipment. The modifications for flight demonstration consisted of modifying the sensor so it could be installed and flow in a Piper PA20 aircraft, equipped for remote control and modifying the display equipment so it could be integrated with the NASA Research RPB (RPRV) remote control cockpit.

Resprout and survival of willows (Salix purpurea and S. incana), Poplars (Populus nigra) and Tamaris (Tamarix gallica) cuttings in marly gullies with Southern aspect in a mountainous and Mediterranean climate (Southern Alps, France)

Science.gov (United States)

Rey, Freddy; Labonne, Sophie; Dangla, Laure; Lavandier, Géraud

2014-05-01

In the Southern French Alps under a mountainous and Mediterranean climate, a current strategy of bioengineering is developed for trapping sediment in marly gullies with surface area less than 1 ha. It is based on the use of structures in the form of brush layers and brush mats of cuttings on deadwood microdams. Purple and white Willows (Salix purpurea and S. incana) are recommended here as they proved their efficiency to resprout and survive in such environment. However, these species installed in Southern gullies did not survive in previous experiments, due to the too harsh conditions of solar radiation and drought. We thus decided to test other species, namely black Poplar (Populus nigra) and Tamaris (Tamarix gallica), which proved their resistance to drought conditions in other experiments. To this view, bioengineering structures have been built in 2010 in eroded marly gullies in the Roubines and Fontaugier catchments (Southern Alps, France). We tested two installation modalities: one in spring and a second in autumn. Seventy-eight bioengineering structures (50 in spring and 28 in autumn), among which 32 made with Poplar cuttings and 28 with Tamaris cuttings, as well as 11 structures with purple Willow and 7 with white Willow as controls, were built in 6 experimental gullies. After 3 observation years for each modality (2010 to 2012, and 2011 to 2013, respectively), results first revealed that Willow species succeeded in surviving in gullies in Southern aspect (76 % for the cuttings installed in spring and 52 % for those installed in autumn), which is in contradiction with previous results. Second, Poplar showed a good ability to survive (62 % for the cuttings installed in spring and 33 % for those installed in autumn). Tamaris obtained the worst score with 26 % and 38 % of survival for the cuttings installed in spring and autumn, respectively. Globally, excepted for Tamaris, survival rates were better for the cuttings installed in spring. The bioengineering

Exploration Medical System Demonstration (EMSD) Project

Science.gov (United States)

Chin, Duane

2012-01-01

The Exploration Medical System Demonstration (EMSD) is a project under the Exploration Medical Capability (ExMC) element managed by the Human Research Program (HRP). The vision for the EMSD is to utilize ISS as a test bed to show that several medical technologies needed for an exploration mission and medical informatics tools for managing evidence and decision making can be integrated into a single system and used by the on-orbit crew in an efficient and meaningful manner. Objectives: a) Reduce and even possibly eliminate the time required for on-orbit crew and ground personnel (which include Surgeon, Biomedical Engineer (BME) Flight Controller, and Medical Operations Data Specialist) to access and move medical data from one application to another. b) Demonstrate that the on-orbit crew has the ability to access medical data/information using an intuitive and crew-friendly software solution to assist/aid in the treatment of a medical condition. c) Develop a common data management framework and architecture that can be ubiquitously used to automate repetitive data collection, management, and communications tasks for all crew health and life sciences activities.

An inspection demonstration program/a quality system

International Nuclear Information System (INIS)

Cox, L.D.

1995-01-01

Mobil relies on tubular manufacturers to consistently supply OCTG which complies with all material requirements of API Specification 5CT. This paper details the Mobil Inspection Demonstration Program; Mobil's method for qualifying ultrasonic inspection systems for use during Mobil receiving inspections. Additionally, the basic fundamentals of the Mobil quality system and acceptance sampling are presented with an emphasis on tracking short-term and long-term supplier performance

Storage and handling of willow from short rotation coppice

Energy Technology Data Exchange (ETDEWEB)

Kofman, P. D.; Spinelli, R.

1997-07-01

During the project two main storage and drying trials were organised. The first trial in 1996 consisted of 14 piles of 6 different size material (whole shoots, via 200 mm chunk, 100 mm chunk, 50 mm chip, 28 mm chips, 25 mm chips) and six different methods of covering: Open air storage, storage under plastic cover, storage under top-cover, airtight storage, unventilated storage under roof, and intermittent ventilation (cooling) under roof. The drying trial in 1997 which consisted of four piles was established in Horsens in the same building as the ventilated trials the year before. Only Austoft 50 mm chips were used for this trial. The four piles were established in February and removed in May. Based on all the results of the trials the following conclusions can be drawn: Storage of willow from short rotation coppice is very difficult. Fine chips, such as producted by the two main harvesting machines Claas and Austoft are not suitable for storage over prolonged periods of time (more than 2 months); fine chips loose a large amount of dry matter and a lot of their lower heating value; fine chips also have a heavy infestation of micro-organisms which might cause working environment problems; short rotation coppice is best delivered straight into the heating plants during harvest; if short rotation coppice has to be stored, then this should be done as whole shoots or large chunk; if short rotation coppice has to be stored as chips for a longer period of time (more than two months), then these chips should be sealed airtight as silage. (EG) EFP-94; EFP-95; EFP-96. 10 refs.

Transpiration and metabolisation of TCE by willow plants - a pot experiment.

Science.gov (United States)

Schöftner, Philipp; Watzinger, Andrea; Holzknecht, Philipp; Wimmer, Bernhard; Reichenauer, Thomas G

2016-01-01

Willows were grown in glass cylinders filled with compost above water-saturated quartz sand, to trace the fate of TCE in water and plant biomass. The experiment was repeated once with the same plants in two consecutive years. TCE was added in nominal concentrations of 0, 144, 288, and 721 mg l(-1). Unplanted cylinders were set-up and spiked with nominal concentrations of 721 mg l(-1) TCE in the second year. Additionally, (13)C-enriched TCE solution (δ(13)C = 110.3 ‰) was used. Periodically, TCE content and metabolites were analyzed in water and plant biomass. The presence of TCE-degrading microorganisms was monitored via the measurement of the isotopic ratio of carbon ((13)C/(12)C) in TCE, and the abundance of (13)C-labeled microbial PLFAs (phospholipid fatty acids). More than 98% of TCE was lost via evapotranspiration from the planted pots within one month after adding TCE. Transpiration accounted to 94 to 78% of the total evapotranspiration loss. Almost 1% of TCE was metabolized in the shoots, whereby trichloroacetic acid (TCAA) and dichloroacetic acid (DCAA) were dominant metabolites; less trichloroethanol (TCOH) and TCE accumulated in plant tissues. Microbial degradation was ruled out by δ(13)C measurements of water and PLFAs. TCE had no detected influence on plant stress status as determined by chlorophyll-fluorescence and gas exchange.

FY 2000 report on the demonstrative research for photovoltaic power generation system in Thailand. Demonstrative study on photovoltaic power generation grid-connected system

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-09-01

In relation to the demonstrative study of the photovoltaic power system that is planned in Libong island, Thailand, the FY 2000 results were reported. In this R and D, construction/demonstrative operation were planned for a photovoltaic power station with a generation output of 100kW, photovoltaic power system in school facilities, and system for transmitting/distributing power to houses by connecting the power station and power system. In this fiscal year, the field survey was conducted together with the alteration from Yao Yai island, for which the demonstrative study was planned at first, to Libong island. The electric equipment was selected which met the requests from Thailand and the results of the field survey, and the basic design of the photovoltaic power generation/transmission/distribution system was completed. Based on this, the design/manufacture of photovoltaic power generation modules, power control equipment, measuring equipment, etc. were made. At the construction site of photovoltaic power station, construction work such as land formation was conducted. Further, Thai engineers who visited Japan did the following: discussions about power system, presence at test/inspection of photovoltaic power generation modules, visits to photovoltaic power stations, wind power stations, etc. (NEDO)

A demonstrator for an integrated subway protection system

Science.gov (United States)

Detoma, E.; Capetti, P.; Casati, G.; Billington, S.

2008-04-01

In 2006 SEPA has carried on the installation and tests of a demonstrator for an integrated subway protection system at a new subway station in the Naples, Italy) metropolitan area. Protection of a subway system is a difficult task given the amount of passengers transported every day. The demonstrator has been limited to non-intrusive detection techniques not to impair the passenger flow into the station. The demonstrator integrates several technologies and products that have been developed by SEPA or are already available on the market (MKS Instruments,...). The main purpose is to provide detection capabilities for attempts to introduce radioactive substances in the subway station, in order to foil possible attempts to place a dirty bomb, and threat detection and identification following release of chemical agents. The system integrates additional sensors such as video surveillance cameras and air flow sensing to complement the basic sensors suite. The need to protect sensitive installations such as subway stations has been highlighted by the series of terroristics actions carried out in recent years in the subway in London. However, given the number of passengers of a metro system, it is impossible to propose security techniques operating in ways similar to the screening of passengers in airports. Passengers screening and threat detection and identification must be quick, non-intrusive and capable of screening a large number of passengers to be applicable to mass transit systems. In 2005 SEPA, a small company operating in the field of trains video-surveillance systems and radiation detectors, started developing an integrated system to provide a comprehensive protection to subway stations, based on ready available or off-the-shelf components in order to quickly develop a reliable system with available technology. We ruled out at the beginning any new development in order to speed up the fielding of the system in less than one year. The system was developed with

Demonstrating Operating System Principles via Computer Forensics Exercises

Science.gov (United States)

Duffy, Kevin P.; Davis, Martin H., Jr.; Sethi, Vikram

2010-01-01

We explore the feasibility of sparking student curiosity and interest in the core required MIS operating systems course through inclusion of computer forensics exercises into the course. Students were presented with two in-class exercises. Each exercise demonstrated an aspect of the operating system, and each exercise was written as a computer…

Transcriptomic Response of Purple Willow (Salix purpurea to Arsenic Stress

Directory of Open Access Journals (Sweden)

Aymeric Yanitch

2017-06-01

Full Text Available Arsenic (As is a toxic element for plants and one of the most common anthropogenic pollutants found at contaminated sites. Despite its severe effects on plant metabolism, several species can accumulate substantial amounts of arsenic and endure the associated stress. However, the genetic mechanisms involved in arsenic tolerance remains obscure in many model plant species used for land decontamination (phytoremediation, including willows. The present study assesses the potential of Salix purpurea cv. ‘Fish Creek’ for arsenic phytoextraction and reveals the genetic responses behind arsenic tolerance, phytoextraction and metabolism. Four weeks of hydroponic exposure to 0, 5, 30 and 100 mg/L revealed that plants were able to tolerate up to 5 mg/L arsenic. Concentrations of 0 and 5 mg/L of arsenic treatment were then used to compare alterations in gene expression of roots, stems and leaves using RNA sequencing. Differential gene expression revealed transcripts encoding proteins putatively involved in entry of arsenic into the roots, storage in vacuoles and potential transport through the plant as well as primary and secondary (indirect toxicity tolerance mechanisms. A major role for tannin as a compound used to relieve cellular toxicity is implicated as well as unexpected expression of the cadmium transporter CAX2, providing a potential means for internal arsenic mobility. These insights into the underpinning genetics of a successful phytoremediating species present novel opportunities for selection of dedicated arsenic tolerant crops as well as the potential to integrate such tolerances into a wider Salix ideotype alongside traits including biomass yield, biomass quality, low agricultural inputs and phytochemical production.

Transcriptomic Response of Purple Willow (Salix purpurea) to Arsenic Stress

Science.gov (United States)

Yanitch, Aymeric; Brereton, Nicholas J. B.; Gonzalez, Emmanuel; Labrecque, Michel; Joly, Simon; Pitre, Frederic E.

2017-01-01

Arsenic (As) is a toxic element for plants and one of the most common anthropogenic pollutants found at contaminated sites. Despite its severe effects on plant metabolism, several species can accumulate substantial amounts of arsenic and endure the associated stress. However, the genetic mechanisms involved in arsenic tolerance remains obscure in many model plant species used for land decontamination (phytoremediation), including willows. The present study assesses the potential of Salix purpurea cv. ‘Fish Creek’ for arsenic phytoextraction and reveals the genetic responses behind arsenic tolerance, phytoextraction and metabolism. Four weeks of hydroponic exposure to 0, 5, 30 and 100 mg/L revealed that plants were able to tolerate up to 5 mg/L arsenic. Concentrations of 0 and 5 mg/L of arsenic treatment were then used to compare alterations in gene expression of roots, stems and leaves using RNA sequencing. Differential gene expression revealed transcripts encoding proteins putatively involved in entry of arsenic into the roots, storage in vacuoles and potential transport through the plant as well as primary and secondary (indirect) toxicity tolerance mechanisms. A major role for tannin as a compound used to relieve cellular toxicity is implicated as well as unexpected expression of the cadmium transporter CAX2, providing a potential means for internal arsenic mobility. These insights into the underpinning genetics of a successful phytoremediating species present novel opportunities for selection of dedicated arsenic tolerant crops as well as the potential to integrate such tolerances into a wider Salix ideotype alongside traits including biomass yield, biomass quality, low agricultural inputs and phytochemical production. PMID:28702037

Feeding preferences of the willow sawfl y Nematus oligospilus (Hymenoptera: Tenthredinidae for commercial Salix clones Preferencias alimentarias de la avispa sierra de los sauces Nematus oligospilus (Hymenoptera: Tenthredinidae por clones de Salix comerciales

Directory of Open Access Journals (Sweden)

Verónica Loetti

2012-06-01

Full Text Available Nematus oligospilus Förster (Hymenoptera: Tenthredinidae is a willow sawfly native to the Northern Hemisphere which became a serious defoliator in willow plantations (Salix spp. of the Southern Hemisphere after being introduced in the early 1980´s. Studies on host preferences provide useful information for the development of pest management strategies where the willow sawfly may produce tree damage and economic loss. Feeding preferences of N. oligospilus larvae were evaluated in laboratory trials by simultaneously offering leaves from four willow tree clones commonly used in commercial plantations in Argentina (Salix babylonica var sacramenta Hortus, Salix nigra Marsch., S. babylonica L. x Salix alba L. 131-27 and Salix matsudana Koidz. x S. alba L. 13-44. Larvae of N. oligospilus fed on leaves from the four clones. However, insects consumed a significantly higher proportion of S. babylonica var sacramenta leaves than of leaves from the other clones. Results indicate that all clones used in the trials were palatable to the insect, and that S. babylonica var sacramenta is the preferred host for larval herbivory.Nematus oligospilus Förster (Hymenoptera: Tenthredinidae, o la avispa sierra de los sauces, es nativa del Hemisferio Norte y se ha convertido en un serio defoliador en plantaciones de sauces (Salix spp. del Hemisferio Sur, después de su introducción a principios de 1980. Los estudios sobre las preferencias de hospedador aportan información útil para el desarrollo de estrategias, donde la avispa sierra puede producir daño a los árboles y pérdidas económicas. Se evaluó la preferencia alimentaria de las larvas de N. oligospilus, mediante ensayos de laboratorio; se ofrecieron en forma simultánea hojas de cuatro clones de sauce, usados comúnmente en plantaciones comerciales en Argentina (Salix babylonica var sacramenta Hortus, Salix nigra Marsch., S. babylonica L. x Salix alba L. 131-27 and Salix matsudana Koidz. x S. alba L. 13

Demonstration of Laser Cutting System for Tube Specimen

Energy Technology Data Exchange (ETDEWEB)

Jin, Y. G.; Kim, G. S.; Heo, G. S.; Baik, S. J.; Kim, H. M.; Ahn, S. B. [KAERI, Daejeon (Korea, Republic of)

2016-05-15

The oxide layer removal system was also developed because the oxide layer on the surface of the irradiated fuel cladding and components interrupted the applying the electric current during the processing. However, it was found that the mechanical testing data of the irradiated specimens with removal of oxide layer was less reliable than the specimens with oxide layer . The laser cutting system using Nd:YAG with fiber optic beam delivery has great potential in material processing applications of the irradiated fuel cladding and components due to non-contact process. Thus, the oxide layer doesn't interrupt the fabrication process during the laser cutting system. In the present study, the laser cutting system was designed to fabricate the mechanical testing specimens from the unirradiated fuel cladding with and without oxide. The feasibility of the laser cutting system was demonstrated for the fabrication of various types of unirradiated specimens. The effect of surface oxide layer was also investigated for machining process of the zirlo fuel cladding and it was found that laser beam machining could be a useful tool to fabricate the specimens with surface oxide layer. Based on the feasibility studies and demonstration, the design of the laser cutting machine for fully or partially automatic and remotely operable system will be proposed and made.

A Franco-German unmanned countermine system demonstrator

Science.gov (United States)

Le Gusquet, F.; Neugebauer, K.; Gerard, F.; Marion, V.; Kaspari, A.; Hembise, D.

2005-05-01

In May 2003, the Federal Republic of Germany and the Republic of France awarded a contract to RHEINMETALL LANDSYSTEME GmbH, Germany), MBDA (France; THALES, France) for the joint development and manufacturing of a technology demonstrator for a vehicle-based close-in countermine system. The objective of this cooperation project, known as MMSR-SYDERA, is to show that, in a full-scale development program, it will be possible to fulfill the joint operational requirements issued by the German and French armies, which are based on the following missions: Fast route opening, Sensitive route opening and Area Clearing . In order to fulfill the three different missions and deal with an extensive array of mine threats, the MMSR-SYDERA countermine system combines two modes of countermine operation, i.e. triggering mines by decoying or detecting mines with sensors for low-order clearing. Thus, the plan calls for the MMSR-SYDERA system to be composed of five vehicles deployed in different configurations in a convoy on the roads to be cleared. This program takes advantage of the latest technologies to reach the objective performances: some innovative decoy tools already validated during real trials and optimized for MMSRSYDERA program, the latest ambitious technologies for detection and confirmation, and state-of-the-art remote-control capabilities, including tele-operation and semi-autonomous autofollow mode, with the highest established performances. An evaluation of the system demonstrator will be carried out at the beginning of 2007.

Biomass production and control of nutrient leaching of willows using different planting methods with special emphasis on an appraisal of the electrical impedance for roots

Energy Technology Data Exchange (ETDEWEB)

Yang Cao

2011-07-01

Willow reproduction can be achieved through vertically or horizontally planted cuttings. Conventionally, plantations are established by inserting cuttings vertically into the soil. There is, however, a lack of information about the biomass production and nutrient leaching of plantations established through horizontally planted cuttings. A greenhouse experiment and a field trial were carried out to investigate whether horizontally planted Salix schwerinii cuttings have a positive effect on stem yield, root distribution and nutrient leaching in comparison with vertically planted cuttings with different planting densities. The shoots' height of horizontally planted cuttings was significantly smaller than that of vertically planted cuttings during the first two weeks after planting in the pot experiment. Thereafter, no significant effect of planting orientation on the stem biomass was observed in the two conducted experiments. In both experiments the total stem biomass increased with the planting density. It was also found that the fine root biomass and the specific root length were not affected by the planting orientation or density, while the fine root surface area and the absorbing root surface area (ARSA) were affected only by the planting density. The planting orientation did not affect the nutrient concentrations in the soil leachate, apart from SO{sub 4}-S and PO{sub 4}-P in the pot experiment. The ARSA in the pot experiment was assessed by using the earth impedance method. The applicability of this method was evaluated in a hydroponic study of willow cuttings where root and stem were measured independently. Electrical resistance had a good correlation with the contact area of the roots with the solution. However, the resistance depended strongly on the contact area of the stem with the solution, which caused a bias in the evaluation of root surface area. A similar experimental set-up with electrical impedance spectroscopy was employed to study the

Phytoremediation potential of willow tress for aquifers contaminated with ethanol-blended gasoline

Energy Technology Data Exchange (ETDEWEB)

Corseuil, H.X. [Universidade Federal de Santa Catarina, Florianopolis (Brazil). Departamento de Engenharia Sanitaria e Ambiental; Moreno, F.N. [Universidade do Sul de Santa Catarina, Palhoca (Brazil). Centro de Ciencias Agrarias e das Engenharias

2001-07-01

Ethanol-blended gasoline has been used in Brazil for 20 years and, probably, is going to be more widely used in North America due to the MtBE environmental effects on groundwater. The potential impacts caused by the presence of ethanol in UST spills are related to the co-solvency effect and the preferential degradation of ethanol over the BTEX compounds. These interactions may increase the length of dissolved hydrocarbon plumes and the costs associated with site remediation. This study investigates the advantages of phytoremediation to overcome the problems associated with the presence of ethanol in groundwater contaminated with gasoline-ethanol mixtures. Experiments were performed under lab conditions with cuttings of Willow tree (Salix babylonica) cultivated hydroponically. Results showed that the cuttings were able to reduce ethanol and benzene concentrations by more than 99% in less than a week. The uptake of both contaminants was confirmed by blank controls and was significantly related to cuttings transpiration capacity. Sorption onto roots biomass also markedly affected the behavior of contaminants in solution. Experiments to evaluate plants' toxicity to ethanol indicated that plants were only affected when aqueous ethanol concentration reached 2000mgl{sup -1}. Results suggest that phytoremediation can be a good complement to intrinsic remediation in shallow aquifer sites contaminated with ethanol-blended gasoline spills. (Author)

Integrated monitoring and surveillance system demonstration project: Phase I accomplishments

International Nuclear Information System (INIS)

Aumeier, S.E.; Walters, B.G.; Crawford, D.C.

1997-01-01

The authors present the results of the Integrated Monitoring and Surveillance System (IMSS) demonstration project Phase I efforts. The rationale behind IMSS development is reviewed and progress in each of the 5 basic tasks is detailed. Significant results include decisions to use Echelon LonWorks networking protocol and Microsoft Access for the data system needs, a preliminary design for the plutonium canning system glovebox, identification of facilities and materials available for the demonstration, determination of possibly affected facility documentation, and a preliminary list of available sensor technologies. Recently imposed changes in the overall project schedule and scope are also discussed and budgetary requirements for competition of Phase II presented. The results show that the IMSS demonstration project team has met and in many cases exceeded the commitments made for Phase I deliverables

Feasibility and demonstration of a cloud-based RIID analysis system

Energy Technology Data Exchange (ETDEWEB)

Wright, Michael C., E-mail: wrightmc@ornl.gov [Oak Ridge National Laboratory, Oak Ridge, TN 37831 (United States); Hertz, Kristin L.; Johnson, William C. [Sandia National Laboratories, Livermore, CA 94551 (United States); Sword, Eric D.; Younkin, James R. [Oak Ridge National Laboratory, Oak Ridge, TN 37831 (United States); Sadler, Lorraine E. [Sandia National Laboratories, Livermore, CA 94551 (United States)

2015-06-01

A significant limitation in the operational utility of handheld and backpack radioisotope identifiers (RIIDs) is the inability of their onboard algorithms to accurately and reliably identify the isotopic sources of the measured gamma-ray energy spectrum. A possible solution is to move the spectral analysis computations to an external device, the cloud, where significantly greater capabilities are available. The implementation and demonstration of a prototype cloud-based RIID analysis system have shown this type of system to be feasible with currently available communication and computational technology. A system study has shown that the potential user community could derive significant benefits from an appropriately implemented cloud-based analysis system and has identified the design and operational characteristics required by the users and stakeholders for such a system. A general description of the hardware and software necessary to implement reliable cloud-based analysis, the value of the cloud expressed by the user community, and the aspects of the cloud implemented in the demonstrations are discussed. - Highlights: • A prototype cloud-based RIID analysis system was implemented and demonstrated. • A cloud-based system was shown to be feasible with currently available technology. • A system study identified the operational characteristics required by the users. • The system study showed that the user community could derive significant benefit. • An architecture was defined for field testing by users in relevant environments.

Feasibility and demonstration of a cloud-based RIID analysis system

International Nuclear Information System (INIS)

Wright, Michael C.; Hertz, Kristin L.; Johnson, William C.; Sword, Eric D.; Younkin, James R.; Sadler, Lorraine E.

2015-01-01

A significant limitation in the operational utility of handheld and backpack radioisotope identifiers (RIIDs) is the inability of their onboard algorithms to accurately and reliably identify the isotopic sources of the measured gamma-ray energy spectrum. A possible solution is to move the spectral analysis computations to an external device, the cloud, where significantly greater capabilities are available. The implementation and demonstration of a prototype cloud-based RIID analysis system have shown this type of system to be feasible with currently available communication and computational technology. A system study has shown that the potential user community could derive significant benefits from an appropriately implemented cloud-based analysis system and has identified the design and operational characteristics required by the users and stakeholders for such a system. A general description of the hardware and software necessary to implement reliable cloud-based analysis, the value of the cloud expressed by the user community, and the aspects of the cloud implemented in the demonstrations are discussed. - Highlights: • A prototype cloud-based RIID analysis system was implemented and demonstrated. • A cloud-based system was shown to be feasible with currently available technology. • A system study identified the operational characteristics required by the users. • The system study showed that the user community could derive significant benefit. • An architecture was defined for field testing by users in relevant environments

100-N Area Strontium-90 Treatability Demonstration Project: Food Chain Transfer Studies for Phytoremediation Along the 100-N Columbia River Riparian Zone

Energy Technology Data Exchange (ETDEWEB)

Fellows, Robert J.; Fruchter, Jonathan S.; Driver, Crystal J.

2009-04-01

Strontium-90 (90Sr) exceeds the U.S. Environmental Protection Agency’s drinking water standards for groundwater (8 picocuries/L) by as much as a factor of 1000 at several locations within the Hanford 100-N Area and along the 100-N Area Columbia River shoreline). Phytoextraction, a managed remediation technology in which plants or integrated plant/rhizosphere systems are employed to phytoextract and/or sequester 90Sr, is being considered as a potential remediation system along the riparian zone of the Columbia River as part of a treatment train that includes an apatite barrier to immobilize groundwater transport of 90Sr. Phytoextraction would employ coyote willow (Salix exigua) to extract 90Sr from the vadose zone soil and aquifer sediments (phytoextraction) and filter 90Sr (rhizofiltration) from the shallow groundwater along the riparian zone of the Columbia River. The stem and foliage of coyote willows accumulating 90Sr may present not only a mechanism to remove the contaminant but also can be viewed as a source of nutrition for natural herbivores, therefore becoming a potential pathway for the isotope to enter the riparian food chain. Engineered barriers such as large and small animal fencing constructed around the field plot will control the intrusion of deer, rodents, birds, and humans. These efforts, however, will have limited effect on mobile phytophagous insects. Therefore, this study was undertaken to determine the potential for food chain transfer by insects prior to placement of the remediation technology at 100-N. Insect types include direct consumers of the sap or liquid content of the plants vascular system (xylem and phloem) by aphids as well as those that would directly consume the plant foliage such as the larvae (caterpillars) of Lepidoptera species. Heavy infestations of aphids feeding on the stems and leaves of willows growing in 90Sr-contaminated soil can accumulate a small amount (~0.15 ± 0.06%) of the total label removed from the soil by

Gender Relation in Willow Trees Don’t Weep Novel (2014 by Fadia Faqir: A Feminist Literary Criticism

Directory of Open Access Journals (Sweden)

Ida Rosida

2017-12-01

Full Text Available This  study  is  aimed  at  finding  gender  relations  between  male  and  female  character  as  they  are depicted  in  Willow  Trees  Don’t  ’Weep  (2014  novel  written  by  Fadia  Faqir.  This  study  employs descriptive qualitative method on feminist literary criticism as a theory to find and reveal gender issues. The text is analyzed by using feminist criticism “woman as reader” to give the evaluation and  interpretation  on  how  woman  writes  about  woman.  The  result  shows  that  there  are  three significant points in which gender relation in patriarchal culture is portrayed in the novel. They are male  domination,  discrimination  towards  women,  and  violence  against  women.  The  results  were evaluated  by  examining  female  character’s  condition  in  a  patriarchal  society  through  woman’s point of view based on her social life and experiences. Moreover, the country where women live is influenced the gender relation. Jordan in this case, has the strongest patriarchal system compared to Pakistan, Afghanistan, and London (the countries where Najwa lived while searching for her father.DOI: 10.15408/insaniyat.v2i1.6586

Global warming potential impact of bioenergy systems

DEFF Research Database (Denmark)

Tonini, Davide; Hamelin, L.; Wenzel, H.

environmental consequences related to land use changes. In this study the global warming potential impact associated with six alternative bioenergy systems based on willow and Miscanthus was assessed by means of life-cycle assessment. The results showed that bioenergy production may generate higher global...... warming impacts than the reference fossil fuel system, when the impacts from indirect land use changes are accounted for. In a life-cycle perspective, only highly-efficient co-firing with fossil fuel achieved a (modest) GHG emission reduction....

Integrated Monitoring and Surveillance System demonstration project. Phase 2 accomplishments

International Nuclear Information System (INIS)

Aumeier, S.E.; Walters, B.G.; Singleterry, R.C.

1997-01-01

The paper presents the results of the Integrated Monitoring and Surveillance System (IMSS) demonstration project Phase 2 efforts. the rationale behind IMSS development is reviewed and progress in each of the 5 basic tasks is detailed. Significant results include further development of the data acquisition system and procurement of necessary hardware/software, options and associated costs for plutonium canning systems and gloveboxes, initiation of facility modifications, determination of possibly affected facility documentation, results from sensor system trade study, and preliminary storage configuration designs. Resources invested during Phase 1 and Phase 2 are summarized and budgetary requirements for completion of Phase 3 presented. The results show that the IMSS demonstration project team has met and in many cases exceeded the commitments made for Phase 2 deliverables

Experimental demonstration of variable weight SAC-OCDMA system for QoS differentiation

Science.gov (United States)

Seyedzadeh, Saleh; Mahdiraji, Ghafour Amouzad; Sahbudin, Ratna Kalos Zakiah; Abas, Ahmad Fauzi; Anas, Siti Barirah Ahmad

2014-10-01

In this paper the experimental and simulation results of variable-weight spectral amplitude coding optical code division multiple access (VW-SAC-OCDMA) system is demonstrated. In the proposed system, three users with weights of 6, 4 and 2 each operating at data rate of 1.25 Gb/s represent video, data and voice services, respectively. Results show that for back-to-back system minimum average power of -20 dBm per chip is required to maintain the acceptable performance. Transmission up to 60 km of fiber is demonstrated. Using mathematical approximation the capacity of VW-SAC-OCDMA system is demonstrated.

Potential for water salvage by removal of non-native woody vegetation from dryland river systems

Science.gov (United States)

Doody, T.M.; Nagler, P.L.; Glenn, E.P.; Moore, G.W.; Morino, K.; Hultine, K.R.; Benyon, R.G.

2011-01-01

Globally, expansion of non-native woody vegetation across floodplains has raised concern of increased evapotranspiration (ET) water loss with consequent reduced river flows and groundwater supplies. Water salvage programs, established to meet water supply demands by removing introduced species, show little documented evidence of program effectiveness. We use two case studies in the USA and Australia to illustrate factors that contribute to water salvage feasibility for a given ecological setting. In the USA, saltcedar (Tamarix spp.) has become widespread on western rivers, with water salvage programs attempted over a 50-year period. Some studies document riparian transpiration or ET reduction after saltcedar removal, but detectable increases in river base flow are not conclusively shown. Furthermore, measurements of riparian vegetation ET in natural settings show saltcedar ET overlaps the range measured for native riparian species, thereby constraining the possibility of water salvage by replacing saltcedar with native vegetation. In Australia, introduced willows (Salix spp.) have become widespread in riparian systems in the Murray-Darling Basin. Although large-scale removal projects have been undertaken, no attempts have been made to quantify increases in base flows. Recent studies of ET indicate that willows growing in permanently inundated stream beds have high transpiration rates, indicating water savings could be achieved from removal. In contrast, native Eucalyptus trees and willows growing on stream banks show similar ET rates with no net water salvage from replacing willows with native trees. We conclude that water salvage feasibility is highly dependent on the ecohydrological setting in which the non-native trees occur. We provide an overview of conditions favorable to water salvage. Copyright ?? 2011 John Wiley & Sons, Ltd.

Demonstrator of atmospheric reentry system with hyperbolic velocity—DASH

Science.gov (United States)

Morita, Yasuhiro; Kawaguchi, Jun'ichiro; Inatani, Yoshifumi; Abe, Takashi

2003-01-01

Among a wide variety of challenging projects planned for the coming decade is the MUSES-C mission designed by the ISAS of Japan. Despite huge amount of data collected by the previous interplanetary spacecraft and probes, the origin and evolution of the solar system still remains unveiled due to their limited information. Thus, our concern has been directed toward a sample return to carry sample from an asteroid back to the earth, which will contribute to better understanding of the system. One of the keys to success is considered the reentry technology with hyperbolic velocity, which has not been demonstrated yet. With this as background, the demonstrator of atmospheric reentry system with hyperbolic velocity, DASH, has been given a commitment to demonstrate the high-speed reentry technology, which will be launched in summer of next year by Japan's H-IIA rocket in a piggyback configuration. The spaceship, composed of a reentry capsule and its carrier, will be injected into a geostationary transfer orbit (GTO) and after several revolutions it will deorbit by burn of a solid propellant deorbit motor. The capsule, identical to that of the sample return mission, can experience the targeted level of thermal environment even from the GTO by tracing a specially designed reentry trajectory.

Cadmium in willow plantations - municipal waste products as fertilizers

International Nuclear Information System (INIS)

Hasselgren, K.

1995-07-01

Plantations of willows (i.e. Salix spp) seem to absorb cadmium (Cd) from arable land to a greater extent than other plant cultivations. Thus, energy forestry, based upon cultivation of Salix, could possibly be used for biofuel production in combination with biological purification of arable land contaminated with Cd by atmospheric deposition and P fertilizers during the passed 100 years. Application of sewage sludge (5-7 ppm Cd of dry solids) up to 550 g Cd per hectare, or 140 g Cd hectare and year, resulted in clearly increased concentrations of Cd in the upper 10 cm layer of the soil. In deeper soil layers the differences compared with control plots were small. Lower rates of sludge application, corresponding to less than 70 g added per hectare and year, did not materially affect the Cd-content in the soil irrespective of layer. A general pattern was that the content of Cd in plant tissues decreased with increased stem diameter, increased age of stems and stands as well as increased biomass growth. Thus, concentrations of Cd in Salix material, in clones from some of the first generation of energy forest plants (S. viminalis, S. dasyclados and S. schwerinii). were fairly high in young stands. In general, 1-year-old shoots contained 5-6 ppm Cd of dry solids in stems and 10-15 ppm in leaves. In older shoots, up to three years, and older stands, up to six years, the Cd contents decreased to 1-2 ppm Cd and 2-4 ppm Cd of dry solids for stems and leaves, respectively. Abundant supplies of water and nutrients seem to stimulate the Cd uptake in Salix in terms of higher concentrations in plant tissues as well as higher plant growth levels compared with conventional energy forestry. Stands with older stems, not irrigated and not fully fertilized resulted in uptake rates in the range of 10-30 g Cd per hectare and year. 14 refs, 9 figs, 1 tab

Analog Readout and Digitizing System for ATLAS TileCal Demonstrator

CERN Document Server

Tang, F; The ATLAS collaboration

2014-01-01

The TileCal Demonstrator is a prototype for a future upgrade to the ATLAS hadron calorimeter when the Large Hadron Collider increases luminosity in year 2023 (HL-LHC). It will be used for functionality and performance tests. The Demonstrator has 48 channels of upgraded readout and digitizing electronics and a new digital trigger capability, but is backwards-compatible with the present detector system insofar as it also provides analog trigger signals. The Demonstrator is comprised of 4 identical mechanical mini-drawers, each equipped with up to 12 photomultipliers (PMTs). The on-detector electronics includes 45 Front-End Boards, each serving an individual PMT; 4 Main Boards, each to control and digitize up to 12 PMT signals, and 4 corresponding high-speed Daughter Boards serving as data hubs between on-detector and off-detector electronics. The Demonstrator is fully compatible with the present system, accepting ATLAS triggers, timing and slow control commands for the data acquisition, detector control, and de...

Transportable vitrification system demonstration on mixed waste. Revision 1

Energy Technology Data Exchange (ETDEWEB)

Zamecnik, J.R.; Whitehouse, J.C. [Westinghouse Savannah River Co., Aiken, SC (United States); Wilson, C.N. [Lockheed Martin Hanford Corp., Richland, WA (United States); Van Ryn, F.R. [Bechtel Jacobs Co., Oak Ridge, TN (United States)

1998-04-22

The Transportable Vitrification System (TVS) is a large scale, fully integrated, vitrification system for the treatment of low-level and mixed wastes in the form of sludges, soils, incinerator ash, and many other waste streams. It was demonstrated on surrogate waste at Clemson University and at the Oak Ridge Reservation (ORR) prior to treating actual mixed waste. Treatment of a combination of dried B and C Pond sludge and CNF sludge was successfully demonstrated at ORR in 1997. The demonstration produced 7,616 kg of glass from 7,328 kg of mixed wastes with a 60% reduction in volume. Glass formulations for the wastes treated were developed using a combination of laboratory crucible studies with the actual wastes and small melter studies at Clemson with both surrogate and actual wastes. Initial characterization of the B and C Pond sludge had not shown the presence of carbon or fluoride, which required a modified glass formulation be developed to maintain proper glass redox and viscosity. The CNF sludge challenges the glass formulations due to high levels of phosphate and iron. The demonstration was delayed several times by permitting problems, a glass leak, and electrical problems. The demonstration showed that the two wastes could be successfully vitrified, although the design glass production rate was not achieved. The glass produced met the Universal Treatment Standards and the emissions from the TVS were well within the allowable permit limits.

Transportable vitrification system demonstration on mixed waste. Revision 1

International Nuclear Information System (INIS)

Zamecnik, J.R.; Whitehouse, J.C.; Wilson, C.N.; Van Ryn, F.R.

1998-01-01

The Transportable Vitrification System (TVS) is a large scale, fully integrated, vitrification system for the treatment of low-level and mixed wastes in the form of sludges, soils, incinerator ash, and many other waste streams. It was demonstrated on surrogate waste at Clemson University and at the Oak Ridge Reservation (ORR) prior to treating actual mixed waste. Treatment of a combination of dried B and C Pond sludge and CNF sludge was successfully demonstrated at ORR in 1997. The demonstration produced 7,616 kg of glass from 7,328 kg of mixed wastes with a 60% reduction in volume. Glass formulations for the wastes treated were developed using a combination of laboratory crucible studies with the actual wastes and small melter studies at Clemson with both surrogate and actual wastes. Initial characterization of the B and C Pond sludge had not shown the presence of carbon or fluoride, which required a modified glass formulation be developed to maintain proper glass redox and viscosity. The CNF sludge challenges the glass formulations due to high levels of phosphate and iron. The demonstration was delayed several times by permitting problems, a glass leak, and electrical problems. The demonstration showed that the two wastes could be successfully vitrified, although the design glass production rate was not achieved. The glass produced met the Universal Treatment Standards and the emissions from the TVS were well within the allowable permit limits

Reliability demonstration test for load-sharing systems with exponential and Weibull components.

Directory of Open Access Journals (Sweden)

Jianyu Xu

Full Text Available Conducting a Reliability Demonstration Test (RDT is a crucial step in production. Products are tested under certain schemes to demonstrate whether their reliability indices reach pre-specified thresholds. Test schemes for RDT have been studied in different situations, e.g., lifetime testing, degradation testing and accelerated testing. Systems designed with several structures are also investigated in many RDT plans. Despite the availability of a range of test plans for different systems, RDT planning for load-sharing systems hasn't yet received the attention it deserves. In this paper, we propose a demonstration method for two specific types of load-sharing systems with components subject to two distributions: exponential and Weibull. Based on the assumptions and interpretations made in several previous works on such load-sharing systems, we set the mean time to failure (MTTF of the total system as the demonstration target. We represent the MTTF as a summation of mean time between successive component failures. Next, we introduce generalized test statistics for both the underlying distributions. Finally, RDT plans for the two types of systems are established on the basis of these test statistics.

Demonstration test of 'multi-purpose incinerating melter system'

International Nuclear Information System (INIS)

Miyazaki, Hitoshi; Tanimoto, Kenichi; Wakui, Hitoshi; Oasada, Kaoru; Ishikawa, Fuyuhiko.

1994-01-01

A Multi-Purpose Incinerating Melter System (MIMS) has been developed as a volume reduction technique for a wide variety of radwastes including flame retardants such as spent resin, and non-combustible materials such as concrete, glass and steel. In the MIMS, these wastes are incinerated and/or melted at temperatures between 1,000 and 1,500degC generated by fossil fueled burner to produce obsidian-like ingots with high integrity. A demonstration test program was carried out from 1989 until 1991 using an engineering-scale demonstration unit. In the test program, various simulated wastes with traces of 60 Co, 54 Mn, 59 Fe, 137 Cs, 22 Na and 106 Ru were treated to obtain decontamination factor (DF) data and leach-resistance data of the products. The summarized results drawn from the 13 runs of demonstrative operations are the following: (1) Most involatile radionuclides are transferred into solidified products. (2) Global DF of the system excluding a HEPA filter ranged 1x10 4 thru 1x10 5 for 60 Co, 2x10 2 thru 2x10 3 for 137 Cs and 2x10 2 thru 1x10 4 for 106 Ru. (3) Leaching resistance of the solidified product is a match for that of a typical borosilicate glass waste form. (author)

Feasibility and demonstration of a cloud-based RIID analysis system

Science.gov (United States)

Wright, Michael C.; Hertz, Kristin L.; Johnson, William C.; Sword, Eric D.; Younkin, James R.; Sadler, Lorraine E.

2015-06-01

A significant limitation in the operational utility of handheld and backpack radioisotope identifiers (RIIDs) is the inability of their onboard algorithms to accurately and reliably identify the isotopic sources of the measured gamma-ray energy spectrum. A possible solution is to move the spectral analysis computations to an external device, the cloud, where significantly greater capabilities are available. The implementation and demonstration of a prototype cloud-based RIID analysis system have shown this type of system to be feasible with currently available communication and computational technology. A system study has shown that the potential user community could derive significant benefits from an appropriately implemented cloud-based analysis system and has identified the design and operational characteristics required by the users and stakeholders for such a system. A general description of the hardware and software necessary to implement reliable cloud-based analysis, the value of the cloud expressed by the user community, and the aspects of the cloud implemented in the demonstrations are discussed.

Demonstration of a transportable storage system for spent nuclear fuel

International Nuclear Information System (INIS)

Shetler, J.R.; Miller, K.R.; Jones, R.E.

1993-01-01

The purpose of this paper is to discuss the joint demonstration project between the Sacramento Municipal Utility District (SMUD) and the US Department of Energy (DOE) regarding the use of a transportable storage system for the long-term storage and subsequent transport of spent nuclear fuel. SMUD's Rancho Seco nuclear generating station was shut down permanently in June 1989. After the shutdown, SMUD began planning the decommissioning process, including the disposition of the spent nuclear fuel. Concurrently, Congress had directed the Secretary of Energy to develop a plan for the use of dual-purpose casks. Licensing and demonstrating a dual-purpose cask, or transportable storage system, would be a step toward achieving Congress's goal of demonstrating a technology that can be used to minimize the handling of spent nuclear fuel from the time the fuel is permanently removed from the reactor through to its ultimate disposal at a DOE facility. For SMUD, using a transportable storage system at the Rancho Seco Independent Spent-Fuel Storage Installation supports the goal of abandoning Rancho Seco's spent-fuel pool as decommissioning proceeds

Demonstration of a free piston Stirling engine driven linear alternator system. Annual report

International Nuclear Information System (INIS)

1978-01-01

The objective of the program is to develop a 2 kW Free Piston Stirling Engine/Linear Alternator Energy Conversion System for an isotopic heat source with a greater than 30% overall efficiency. The work was broken up into two phases. Phase I demonstrated the feasibility of the energy conversion system through analysis and experimental testing of the individual components. Phase II is a two-year effort to design, fabricate, and test a prototype demonstrator energy conversion system. The reprt documents the work performed during October 1976 through September 1977, the first year of Phase II. Details of the tasks are presented in five major sections: (1) Linear Alternator Development; (2) Engine/Alternator System Demonstration; (3) Demonstrator Preliminary Design; (4) Demonstrator Detailed Design; and (5) Development of Free Piston Stirling Engine Computer Simulation

Establishment and implementation of performance demonstration system for ultrasonic examination in Korea

International Nuclear Information System (INIS)

Kim, Yong-sik

2007-01-01

Korea Electric Power Research Institute (KEPRI) and Korea Hydro and Nuclear Power Company (KHNP) developed Korean Performance Demonstration (KPD) system for ultrasonic examination applicable to pressurized light-water reactor and pressurized heavy-water reactor power plants in accordance with ASME Sec. XI App. VIII. In order to develop the KPD system following works were completed. 1) Surveying the welds on piping of all nuclear power plants in Korea, 2) Surveying the bolting configuration of all nuclear power plant in Korea, 3) Determining the number and type of test specimens, 4)Designing the test and the practice specimens, 5) Developing quality assurance procedures for the fabrication of test specimens and system management, 6) Developing generic procedures for manual ultrasonic test, 7) Fabrication and fingerprint of test specimen. After establishing the KPD system, round robin tests were conducted to evaluate the accuracy and reliability of examination results by comparing traditional ASME code and performance demonstration method. KEPRI/KHNP had successfully developed the KPD system to fulfill the performance demonstration requirements of ASME Sec. XI, Appendix VIII, and are executing the performance demonstration test for ultrasonic examination system. (author)

Solar Power System Options for the Radiation and Technology Demonstration Spacecraft

Science.gov (United States)

Kerslake, Thomas W.; Haraburda, Francis M.; Riehl, John P.

2000-01-01

The Radiation and Technology Demonstration (RTD) Mission has the primary objective of demonstrating high-power (10 kilowatts) electric thruster technologies in Earth orbit. This paper discusses the conceptual design of the RTD spacecraft photovoltaic (PV) power system and mission performance analyses. These power system studies assessed multiple options for PV arrays, battery technologies and bus voltage levels. To quantify performance attributes of these power system options, a dedicated Fortran code was developed to predict power system performance and estimate system mass. The low-thrust mission trajectory was analyzed and important Earth orbital environments were modeled. Baseline power system design options are recommended on the basis of performance, mass and risk/complexity. Important findings from parametric studies are discussed and the resulting impacts to the spacecraft design and cost.

Estimating System-wide Impacts of Smart Grid Demonstrations

Energy Technology Data Exchange (ETDEWEB)

Schneider, Kevin P.; Lightner, Eric M.; Fuller, Jason C.

2015-03-01

Quantifying the impact of a new technology on a single specific distribution feeder is relatively easy, but it does not provide insight into the complexities and variations of a system-wide deployment. It is the inability to extrapolate system-wide impacts that hinders the deployment of many promising new technologies. This paper presents a method of extrapolating technology impacts, either simulated or from a field demonstration, from a limited number of distribution feeders to a system-wide impact. The size of the system can vary from the service territory of a single utility, to a region, or to an entire country. The paper will include an example analysis using the United States Department of Energy (DOE) funded Smart Grid Investment Grant (SGIG) projects, extrapolating their benefits to a national level.

Proposal for Construction/Demonstration/Implementation of A Material Handling System

International Nuclear Information System (INIS)

Jim Jnatt

2001-01-01

Vortec Corporation, the United States Enrichment Corporation (USEC) and DOE/Paducah propose to complete the technology demonstration and the implementation of the Material Handling System developed under Contract Number DE-AC21-92MC29120. The demonstration testing and operational implementation will be done at the Paducah Gaseous Diffusion Plant. The scope of work, schedule and cost for the activities are included in this proposal. A description of the facility to be constructed and tested is provided in Exhibit 1, attached. The USEC proposal for implementation at Paducah is presented in Exhibit 2, and the commitment letters from the site are included in Exhibit 3. Under our agreements with USEC, Bechtel Jacobs Corporation and DOE/Paducah, Vortec will be responsible for the construction of the demonstration facility as documented in the engineering design package submitted under Phase 4 of this contract on August 9, 2001. USEC will have responsibility for the demonstration testing and commercial implementation of the plant. The demonstration testing and initial commercial implementation of the technology will be achieved by means of a USEC work authorization task with the Bechtel Jacobs Corporation. The initial processing activities will include the processing of approximately 4,250 drums of LLW. Subsequent processing of LLW and TSCA/LLW will be done under a separate contract or work authorization task. To meet the schedule for commercial implementation, it is important that the execution of the Phase 4 project option for construction of the demonstration system be executed as soon as possible. The schedule we have presented herein assumes initiation of the construction phase by the end of September 2001. Vortec proposes to complete construction of the demonstration test system for an estimated cost of $3,254,422. This price is based on the design submitted to DOE/NETL under the Phase 4 engineering design deliverable (9 august 2001). The cost is subject to the

Demonstration test of 'multi-purpose incinerating melter system'

Energy Technology Data Exchange (ETDEWEB)

Miyazaki, Hitoshi; Tanimoto, Kenichi [Power Reactor and Nuclear Fuel Development Corp., Oarai, Ibaraki (Japan). Oarai Engineering Center; Wakui, Hitoshi; Oasada, Kaoru; Ishikawa, Fuyuhiko

1994-03-01

A Multi-Purpose Incinerating Melter System (MIMS) has been developed as a volume reduction technique for a wide variety of radwastes including flame retardants such as spent resin, and non-combustible materials such as concrete, glass and steel. In the MIMS, these wastes are incinerated and/or melted at temperatures between 1,000 and 1,500degC generated by fossil fueled burner to produce obsidian-like ingots with high integrity. A demonstration test program was carried out from 1989 until 1991 using an engineering-scale demonstration unit. In the test program, various simulated wastes with traces of [sup 60]Co, [sup 54]Mn, [sup 59]Fe, [sup 137]Cs, [sup 22]Na and [sup 106]Ru were treated to obtain decontamination factor (DF) data and leach-resistance data of the products. The summarized results drawn from the 13 runs of demonstrative operations are the following: (1) Most involatile radionuclides are transferred into solidified products. (2) Global DF of the system excluding a HEPA filter ranged 1x10[sup 4] thru 1x10[sup 5] for [sup 60]Co, 2x10[sup 2] thru 2x10[sup 3] for [sup 137]Cs and 2x10[sup 2] thru 1x10[sup 4] for [sup 106]Ru. (3) Leaching resistance of the solidified product is a match for that of a typical borosilicate glass waste form. (author).

NASA Systems Autonomy Demonstration Project - Development of Space Station automation technology

Science.gov (United States)

Bull, John S.; Brown, Richard; Friedland, Peter; Wong, Carla M.; Bates, William

1987-01-01

A 1984 Congressional expansion of the 1958 National Aeronautics and Space Act mandated that NASA conduct programs, as part of the Space Station program, which will yield the U.S. material benefits, particularly in the areas of advanced automation and robotics systems. Demonstration programs are scheduled for automated systems such as the thermal control, expert system coordination of Station subsystems, and automation of multiple subsystems. The programs focus the R&D efforts and provide a gateway for transfer of technology to industry. The NASA Office of Aeronautics and Space Technology is responsible for directing, funding and evaluating the Systems Autonomy Demonstration Project, which will include simulated interactions between novice personnel and astronauts and several automated, expert subsystems to explore the effectiveness of the man-machine interface being developed. Features and progress on the TEXSYS prototype thermal control system expert system are outlined.

Willow Short Rotation Coppice Trial in a Former Mining Area in Northern Spain: Effects of Clone, Fertilization and Planting Density on Yield after Five Years

Directory of Open Access Journals (Sweden)

María Castaño-Díaz

2018-03-01

Full Text Available A willow short rotation coppice (SRC trial was conducted on former mining land in northern Spain over a period of five years, with the purpose of evaluating the effects on yield of two planting densities (9876 and 14,815 cuttings ha−1, three treatments (control, two levels of nitrogen, phosphorus and potassium compound fertilizer (NPK plus weed control and three willow clones (Björn, Inger, Olof. The area was subsoiled, ploughed, harrowed and fertilized with NPK before trial establishment. A randomized block design was applied, with three replications of each treatment in a total of 54 plots, each of an area of 400 m2. The effects of the interactions between the various factors on yield and other growth parameters were also studied. The clone factor significantly affected the number of shoots per stool (greatest for the Inger clone and the Olof clone, which showed the lowest mortality rate and produced the largest trees and largest quantity of biomass. The combined application of fertilizer and herbicide also significantly increased the values of all response variables considered, except the mortality rate. The planting density did not significantly affect the response variables. Clone × treatment interactions were significant for the shoots per stool, height, diameter and biomass variables, and the Olof clone displayed the highest height and diameter growth and yield. The results obtained in the first rotation indicate that the Olof clone adapted well to the trial conditions and therefore would be appropriate for producing biomass in abandoned mine land in Asturias. These findings will help in the development of strategies for the establishment and management of SRC on marginal land.

Extreme drought alters frequency and reproductive success of floaters in Willow Flycatchers

Science.gov (United States)

Theimer, Tad; Sogge, Mark K.; Cardinal, Suzanne N.; Durst, Scott L.; Paxton, Eben H.

2018-01-01

Changes in habitat quality, including those caused by extreme events like droughts and floods, could alter costs and benefits of territoriality and thereby the prevalence and reproductive consequences for individuals capable of breeding that do not do so (floaters). We studied floating behavior in a population of Southwestern Willow Flycatchers (Empidonax traillii extimus) in central Arizona during one year of extreme drought, one year of lake inundation, and three years of near average precipitation. In all years, most floaters were second year (SY) males, and most subsequently settled outside of the patch where they were detected in the floating year, suggesting that floaters did not “queue” at high-quality territories in order to achieve higher reproductive success in subsequent years. Instead, cohorts that floated in non-drought years had lower apparent survival and lower reproductive success compared to territorial birds. In the extreme drought year, however, the number of floaters was 1.5 times greater than in all other years combined, more females floated, and apparent survival and mean annual productivity in subsequent years was higher for males that floated in that year than for those that were territorial. Inundation of habitat due to rising reservoir levels did not result in an increase in floaters because many birds nested in inundated areas where trees projected above the water so that the relative amount of available habitat was not reduced to the extent habitat models predicted. Overall, our results indicate that the prevalence and reproductive and demographic consequences of floating can change under extreme climatic events like severe drought.

Development and demonstration of near-real-time accounting systems for reprocessing plants

International Nuclear Information System (INIS)

Cobb, D.D.; Hakkila, E.A.; Dayem, H.A.; Shipley, J.P.; Baker, A.L.

1981-01-01

A program to develop and demonstrate near-real-time accounting systems for reprocessing plants has been active at Los Alamos since 1976. The technology has been developed through modeling and simulation of process operation and measurement systems and evaluation of these data using decision analysis techniques. Aspects of near-real-time systems have been demonstrated successfully at the AGNS reprocessng plant as part of a joint study of near-real-time accounting

Final Technical Report for EE0006091: H2Pump Hydrogen Recycling System Demonstration

Energy Technology Data Exchange (ETDEWEB)

Staudt, Rhonda [H2Pump LLC, Latham, NY (United States)

2017-02-21

The objective of this project is to demonstrate the product readiness and to quantify the benefits and customer value proposition of H2Pump’s Hydrogen Recycling System (HRS-100™) by installing and analyzing the operation of multiple prototype 100-kg per day systems in real world customer locations. The data gathered will be used to measure reliability, demonstrate the value proposition to customers, and validate our business model. H2Pump will install, track and report multiple field demonstration systems in industrial heat treating and semi-conductor applications. The customer demonstrations will be used to develop case studies and showcase the benefits of the technology to drive market adoption.

Twenty years experience with constructed wetland systems in Denmark - what did we learn?

DEFF Research Database (Denmark)

Brix, Hans; Schierup, Hans-Henrik; Arias, Carlos Alberto

2007-01-01

, the reeds do not increase the hydraulic conductivity of cohesive soils as much as necessary to secure sub-surface flow. Operation needs of soil-based reed beds are low and normally restricted to emptying of the sedimentation tank, cleaning of the distribution system and mowing of the grass around the system...... wetland systems are either compact vertical flow systems which provide good nitrification, willow systems with no discharge or restored wetland systems for nitrate removal. If efficient removal of phosphorus is required, this is achieved by chemical precipitation in the sedimentation tank....

Upgrade Analog Readout and Digitizing System for ATLAS TileCal Demonstrator

CERN Document Server

Tang, F; Anderson, K; Bohm, C; Hildebrand, K; Muschter, S; Oreglia, M

2015-01-01

The TileCal Demonstrator is a prototype for a future upgrade to the ATLAS hadron calorimeter when the Large Hadron Collider increases luminosity in year 2023 (HL-LHC). It will be used for functionality and performance tests. The Demonstrator has 48 channels of upgraded readout and digitizing electronics and a new digital trigger capability, but is backwards-compatible with the present detector system insofar as it also provides analog trigger signals. The Demonstrator is comprised of 4 identical mechanical mini-drawers, each equipped with up to 12 photomultipliers (PMTs). The on-detector electronics includes 45 Front-End Boards, each serving an individual PMT; 4 Main Boards, each to control and digitize up to 12 PMT signals, and 4 corresponding high-speed Daughter Boards serving as data hubs between on-detector and off-detector electronics. The Demonstrator is fully compatible with the present system, accepting ATLAS triggers, timing and slow control commands for the data acquisition, detector control, and de...

Choices of action and its influence on farmers' attitudes regarding willow and reed canary grass cultivation; Betydelsen av olika handlingsalternativ foer oekat intresse hos lantbrukare att odla salix och roerflen

Energy Technology Data Exchange (ETDEWEB)

Jonsson, Aasa; Paulrud, Susanne; Laitila, Thomas

2010-02-15

The contribution of energy crops from the agricultural sector is an example of a resource that has a potential to increase substantially in the near future. However, one problem is the lack of interest in cultivating energy crops within the agricultural Several studies have shown that there are a number of reasons for farmers not becoming involved in energy crops. Besides biological aspects, market potential and profitability the farmers are also affected by the available resources on the farm, the effect of the crops on the surroundings, work load, liquidity and the perceived risks. The overall aim with the present study is to increase the knowledge about how to change farmers' attitudes regarding energy crop cultivation, i.e. making them more interested. This study also shows that there is a large fraction of farmers that generally believe they have no or little knowledge of energy crops, such as willow, reed canary grass and hemp. The fraction of farmers considering there is a larger probability of future cultivation of these crops with increased knowledge is also quite large. Energy crop cultivation does not suit everybody. Generally, growing willow and reed canary grass is an alternative for farmers having another business besides agricultural business. Characteristics for these farms are working hours <1500 hours and that the machines are partly owned

Magnetic Launch Assist System Demonstration Test

Science.gov (United States)

2001-01-01

Engineers at the Marshall Space Flight Center (MSFC) have been testing Magnetic Launch Assist Systems, formerly known as Magnetic Levitation (MagLev) technologies. To launch spacecraft into orbit, a Magnetic Launch Assist system would use magnetic fields to levitate and accelerate a vehicle along a track at a very high speed. Similar to high-speed trains and roller coasters that use high-strength magnets to lift and propel a vehicle a couple of inches above a guideway, the launch-assist system would electromagnetically drive a space vehicle along the track. A full-scale, operational track would be about 1.5-miles long and capable of accelerating a vehicle to 600 mph in 9.5 seconds. This photograph shows a subscale model of an airplane running on the experimental track at MSFC during the demonstration test. This track is an advanced linear induction motor. Induction motors are common in fans, power drills, and sewing machines. Instead of spinning in a circular motion to turn a shaft or gears, a linear induction motor produces thrust in a straight line. Mounted on concrete pedestals, the track is 100-feet long, about 2-feet wide, and about 1.5- feet high. The major advantages of launch assist for NASA launch vehicles is that it reduces the weight of the take-off, the landing gear, the wing size, and less propellant resulting in significant cost savings. The US Navy and the British MOD (Ministry of Defense) are planning to use magnetic launch assist for their next generation aircraft carriers as the aircraft launch system. The US Army is considering using this technology for launching target drones for anti-aircraft training.

In-Space Hybrid Energy Storage System Demonstration on CSUNSat1

Data.gov (United States)

National Aeronautics and Space Administration — Objective: Flight demonstrate the JPL Hybrid Energy Storage System (low temperature, high power) using the SSTP-funded CSUNSat1 CubeSat: Environmental testing...

Intergovernmental Advanced Stationary PEM Fuel Cell System Demonstration Final Report

Energy Technology Data Exchange (ETDEWEB)

Rich Chartrand

2011-08-31

A program to complete the design, construction and demonstration of a PEMFC system fuelled by Ethanol, LPG or NG for telecom applications was initiated in October 2007. Early in the program the economics for Ethanol were shown to be unfeasible and permission was given by DOE to focus on LPG only. The design and construction of a prototype unit was completed in Jun 2009 using commercially available PEM FC stack from Ballard Power Systems. During the course of testing, the high pressure drop of the stack was shown to be problematic in terms of control and stability of the reformer. Also, due to the power requirements for air compression the overall efficiency of the system was shown to be lower than a similar system using internally developed low pressure drop FC stack. In Q3 2009, the decision was made to change to the Plug power stack and a second prototype was built and tested. Overall net efficiency was shown to be 31.5% at 3 kW output. Total output of the system is 6 kW. Using the new stack hardware, material cost reduction of 63% was achieved over the previous Alpha design. During a November 2009 review meeting Plug Power proposed and was granted permission, to demonstrate the new, commercial version of Plug Power's telecom system at CERL. As this product was also being tested as part of a DOE Topic 7A program, this part of the program was transferred to the Topic 7A program. In Q32008, the scope of work of this program was expanded to include a National Grid demonstration project of a micro-CHP system using hightemperature PEM technology. The Gensys Blue system was cleared for unattended operation, grid connection, and power generation in Aug 2009 at Union College in NY state. The system continues to operate providing power and heat to Beuth House. The system is being continually evaluated and improvements to hardware and controls will be implemented as more is learned about the system's operation. The program is instrumental in improving the

A Modular Instrumentation System for NASA's Habitat Demonstration Unit

Science.gov (United States)

Rojdev, Kristina; Kennedy, Kriss; Yim, Hester; Wagner, Raymond S.; Hong, Todd; Studor, George; Delaune, Paul

2010-01-01

NASA's human spaceflight program is focused on developing technologies to expand the reaches of human exploration and science activities beyond low earth orbit. A critical aspect of living in space or on planetary surfaces is habitation, which provides a safe and comfortable space in which humans can live and work. NASA is seeking out the best option for habitation by exploring several different concepts through the Habitat Demonstration Unit (HDU) project. The purpose of this HDU is to develop a fully autonomous habitation system that enables human exploration of space. One critical feature of the HDU project that helps to accomplish its mission of autonomy is the instrumentation system that monitors key subsystems operating within a Habitat configuration. The following paper will discuss previous instrumentation systems used in analog habitat concepts and how the current instrumentation system being implemented on the HDU1-PEM, or pressurized excursion module, is building upon the lessons learned of those previous systems. Additionally, this paper will discuss the benefits and the limitations of implementing a wireless sensor network (WSN) as the basis for data transport in the instrumentation system. Finally, this paper will address the experiences and lessons learned with integration, testing prior to deployment, and field testing at the JSC rock yard. NASA is developing the HDU1-PEM as a step towards a fully autonomous habitation system that enables human exploration of space. To accomplish this purpose, the HDU project is focusing on development, integration, testing, and evaluation of habitation systems. The HDU will be used as a technology pull, testbed, and integration environment in which to advance NASA's understanding of alternative mission architectures, requirements, and operations concepts definition and validation. This project is a multi-year effort. In 2010, the HDU1-PEM will be in a pressurized excursion module configuration, and in 2011 the

Photovoltaic Test and Demonstration Project. [for solar cell power systems

Science.gov (United States)

Forestieri, A. F.; Brandhorst, H. W., Jr.; Deyo, J. N.

1976-01-01

The Photovoltaic Test and Demonstration Project was initiated by NASA in June, 1975, to develop economically feasible photovoltaic power systems suitable for a variety of terrestrial applications. Objectives include the determination of operating characteristic and lifetimes of a variety of solar cell systems and components and development of methodology and techniques for accurate measurements of solar cell and array performance and diagnostic measurements for solar power systems. Initial work will be concerned with residential applications, with testing of the first prototype system scheduled for June, 1976. An outdoor 10 kW array for testing solar power systems is under construction.

ETV/ESTCP Demonstration Plan - Demonstration and Verification of a Turbine Power Generation System Utilizing Renewable Fuel: Landfill Gas

Science.gov (United States)

This Test and Quality Assurance Plan (TQAP) provides data quality objections for the success factors that were validated during this demonstration include energy production, emissions and emission reductions compared to alternative systems, economics, and operability, including r...

Fiscal 2000 achievement report. International demonstrative development of photovoltaic power generation system (Demonstrative study on grid-connected photovoltaic power generation system in Thailand); 2000 nendo seika hokokusho. Taiyoko hatsuden system kokusai kyodo jissho kaihatsu - Taiyoko hatsuden keitou renkei system jissho kenkyu (Tai)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-09-01

A demonstrative study was conducted in Thailand for grasping the effect on small electricity grids when several photovoltaic power generation systems, including AC modules, are connected to the grid. In fiscal 2000, surveys and studies were conducted about the data of the local power system, where to install the demonstrative system, and how to install the same, which were necessary for working out a basic design for Libong Island newly designated as the site for the demonstrative system. It was then concluded that the demonstrative system be a grid-connected 100 kW-level photovoltaic system comprising one main photovoltaic power station (85 kW), photovoltaic power systems for school buildings (3-6 kW, three schools), and AC modules (110 W, 10 locations). The manufacture of solar cell modules, grid-connected power conditioners, and measuring devices were completed. Civil engineering work and construction were under way on the site, including the construction of a management building, installation of concrete bases for solar cell arrays, construction of fences surrounding the site, and so forth. (NEDO)

Scintiangiographic demonstration of parasitization of systemic blood supply by inflammatory lung disease

Energy Technology Data Exchange (ETDEWEB)

Schlesinger, A.E.; Lee, V.W.; Shapiro, J.H.

1985-03-01

An unusual case in which a computed tomogram demonstrated abnormal, enlarged vessels in the right lower lobe of the lung and suggested an arteriovenous malformation is presented. A scintiangiogram showed abnormal systemic supply to this area in the aortic phase. Contrast angiography demonstrated hypertrophy of the right inferior phrenic artery with abnormal systemic supply to the pleura and parenchyma of the right lower lobe, presumably on the basis of old infection.

Five willow varieties cultivated across diverse field environments reveal stem density variation associated with high tension wood abundance

Directory of Open Access Journals (Sweden)

Nicolas eBerthod

2015-10-01

Full Text Available Sustainable and inexpensive production of biomass is necessary to make biofuel production feasible, but represents a challenge. Five short rotation coppice (SRC willow cultivars, selected for high biomass yield, were cultivated on sites at four diverse regions of Quebec to determine their bioenergy potential in contrasting environments. Wood composition and anatomical traits were characterized. Tree height and stem diameter were measured to evaluate growth performance of the cultivars according to the diverse pedoclimatic conditions. Each cultivar showed very specific responses to its environment. While no significant variation in lignin content was observed between sites, there was variation between cultivars. Surprisingly, the pattern of substantial genotype variability in stem density was maintained across all sites. However, wood anatomy did differ between sites in a cultivar (producing high and low density wood, suggesting a probable response to an abiotic stress. Furthermore, twice as many cellulose-rich G-fibers, comprising over 50 % of secondary xylem, were also found in the high density wood, a finding with potential to bring higher value to the lignocellulosic bioethanol industry

DEMONSTRATION OF AN ADVANCED INTEGRATED CONTROL SYSTEM FOR SIMULTANEOUS EMISSIONS REDUCTION

Energy Technology Data Exchange (ETDEWEB)

Suzanne Shea; Randhir Sehgal; Ilga Celmins; Andrew Maxson

2002-02-01

The primary objective of the project titled ''Demonstration of an Advanced Integrated Control System for Simultaneous Emissions Reduction'' was to demonstrate at proof-of-concept scale the use of an online software package, the ''Plant Environmental and Cost Optimization System'' (PECOS), to optimize the operation of coal-fired power plants by economically controlling all emissions simultaneously. It combines physical models, neural networks, and fuzzy logic control to provide both optimal least-cost boiler setpoints to the boiler operators in the control room, as well as optimal coal blending recommendations designed to reduce fuel costs and fuel-related derates. The goal of the project was to demonstrate that use of PECOS would enable coal-fired power plants to make more economic use of U.S. coals while reducing emissions.

Non-Flow-Through Fuel Cell System Test Results and Demonstration on the SCARAB Rover

Science.gov (United States)

Scheidegger, Brianne, T.; Burke, Kenneth A.; Jakupca, Ian J.

2012-01-01

This paper describes the results of the demonstration of a non-flow-through PEM fuel cell as part of a power system on the SCARAB rover. A 16-cell non-flow-through fuel cell stack from Infinity Fuel Cell and Hydrogen, Inc. was incorporated into a power system designed to act as a range extender by providing power to the rover s hotel loads. This work represents the first attempt at a ground demonstration of this new technology aboard a mobile test platform. Development and demonstration were supported by the Office of the Chief Technologist s Space Power Systems Project and the Advanced Exploration System Modular Power Systems Project.

The Demonstrator for the European Plate Observing System (EPOS)

Science.gov (United States)

Hoffmann, T. L.; Euteneuer, F.; Ulbricht, D.; Lauterjung, J.; Bailo, D.; Jeffery, K. G.

2014-12-01

An important outcome of the 4-year Preparatory Phase of the ESFRI project European Plate Observing System (EPOS) was the development and first implementation of the EPOS Demonstrator by the project's ICT Working Group 7. The Demonstrator implements the vertical integration of the three-layer architectural scheme for EPOS, connecting the Integrated Core Services (ICS), Thematic Core Services (TCS) and the National Research Infrastructures (NRI). The demonstrator provides a single GUI with central key discovery and query functionalities, based on already existing services by the seismic, geologic and geodetic communities. More specifically the seismic services of the Demonstrator utilize webservices and APIs for data and discovery of raw seismic data (FDSN webservices by the EIDA Network), events (Geoportal by EMSC) and analytical data products (e.g., hazard maps by EFEHR via OGC WMS). For geologic services, the EPOS Demonstrator accesses OneGeology Europe which serves the community with geologic maps and point information via OGC webservices. The Demonstrator also provides access to raw geodetic data via a newly developed universal tool called GSAC. The Demonstrator itself resembles the future Integrated Core Service (ICS) and provides direct access to the end user. Its core functionality lies in a metadata catalogue, which serves as the central information hub and stores information about all RIs, related persons, projects, financial background and technical access information. The database schema of the catalogue is based on CERIF, which has been slightly adapted. Currently, the portal provides basic query functions as well as cross domain search. [www.epos.cineca.it

Policy Analysis Screening System (PASS) demonstration: sample queries and terminal instructions

Energy Technology Data Exchange (ETDEWEB)

None

1979-10-16

This document contains the input and output for the Policy Analysis Screening System (PASS) demonstration. This demonstration is stored on a portable disk at the Environmental Impacts Division. Sample queries presented here include: (1) how to use PASS; (2) estimated 1995 energy consumption from Mid-Range Energy-Forecasting System (MEFS) data base; (3) pollution projections from Strategic Environmental Assessment System (SEAS) data base; (4) diesel auto regulations; (5) diesel auto health effects; (6) oil shale health and safety measures; (7) water pollution effects of SRC; (8) acid rainfall from Energy Environmental Statistics (EES) data base; 1990 EIA electric generation by fuel type; sulfate concentrations by Federal region; forecast of 1995 SO/sub 2/ emissions in Region III; and estimated electrical generating capacity in California to 1990. The file name for each query is included.

Trace Element Concentration and Speciation in Selected Mining-Contaminated Soils and Water in Willow Creek Floodplain, Colorado

Directory of Open Access Journals (Sweden)

R. Burt

2011-01-01

Full Text Available Long-term mining activities in the mountains around Creede, Colorado have resulted in significant contamination in soils and water in the Willow Creek floodplain. Total major and trace were determined for soils and water and sequential chemical extraction for soils. Objectives were to determine concentrations and potential reactivity of trace elements and investigate their relationship with other soil and water properties. Water trace elements showed significant variability among sites, ranging from 347 to 12108 μg/L. Relative trend showed (Zn > Sr > Ba > (Mn > W > Cd > (Sn > V ≈ Ni ≈ Cu > Co > (Ag. Soil trace elements showed significant short-range spatial variability, ranging from 2819 to 19274 mg/kg. Relative trend showed (Pb ≈ Zn > Mn > Ba > P > (As > Cu > Sr > V > Cd > Sb ≈ Ag > (Co ≈ Cr > Mo ≈ Sn ≈ Ni > (Be ≈ W > Se ≈ Hg. Predominant fractions were oxide, specifically-sorbed/carbonate bound, and residual. Water soluble and exchangeable fractions showed (Zn ≈ Cd > Pb and Cd > Zn > Pb, respectively. Mobility factors for highly contaminated soils showed Cd ≈ Zn > Pb > Cu > As.

Demonstration of a utility industry horizontal drilling system: Horizontal well AMH-5 installation report

International Nuclear Information System (INIS)

1992-01-01

The Department of Energy's Office of Technology Development initiated an integrated demonstration of innovative technologies and systems for cleanup of VOCs in soils and groundwater at the Savannah River Site (SRS) in 1989. The overall goal of the program is demonstration of multiple technologies and systems in the fields of drilling, characterization, monitoring, and remediation at a single test bed. Innovative technologies are compared to one another and to baseline technologies in terms of technical performance and cost effectiveness. Transfer of successfully demonstrated technologies and systems to DOE environmental restoration organizations, to other government agencies, and to industry is a critical part of the program. Directional drilling has been shown to be a successful technique for enhancing access to the subsurface, thus improving remediation systems, especially remediation systems which perform in situ. Demonstration of an innovative directional drilling system at the Integrated Demonstration Site at the SRS, was initiated in June of 1992. The directional drilling system was designed to install an in situ remediation system. The drilling system is an experimental compaction/dry drilling technique developed by Charles Machine Works (Ditch Witch reg-sign) of Perry, Oklahoma. A horizontal well was installed in the M Area of the SRS below and parallel to an abandoned tile process sewer line. The installation of the horizontal well was a two-part process. Part one consisted of drilling the borehole, and part two was the horizontal well completion

EDSN: A First Demonstration of a Distributed System of Nanosatellites

Science.gov (United States)

Hu, Steven Hung Kee; Smith, Harrison Brodsky

2013-01-01

Edison Demonstration of SmallSat Networks (EDSN) is the first demonstration of a distributed system of nano-scale satellites to use intersatellite communication while working towards common science and technology goals. This unique mission configuration poses key technological challenges, including multi-satellite deployment, close proximity flight, cross-satellite communications, and simplified and effective operations. Tackling these challenges has required extensive development on EDSNs guidance navigation and control (GNC) and flight software systems. Although use of COTS component is common to the CubeSat community, it is prudent to point out that utilization of these components enables EDSN to accomplish its objectives at relatively low cost ($12M) in comparison to current multi-satellite missions capable of cross-link communications. EDSN is on cost and schedule with flight unit shipment in August 2013. This paper aims to update the community of EDSN's progress since SRR and speaks to the approach EDSN has taken to resolve some of the main issues revolving around a distributed system of nano-scale satellites.

Bi-Modal Face and Speech Authentication: a BioLogin Demonstration System

OpenAIRE

Marcel, Sébastien; Mariéthoz, Johnny; Rodriguez, Yann; Cardinaux, Fabien

2006-01-01

This paper presents a bi-modal (face and speech) authentication demonstration system that simulates the login of a user using its face and its voice. This demonstration is called BioLogin. It runs both on Linux and Windows and the Windows version is freely available for download. Bio\\-Login is implemented using an open source machine learning library and its machine vision package.

Design demonstrations for category B tank systems at Oak Ridge National Laboratory, Oak Ridge, Tennessee

Energy Technology Data Exchange (ETDEWEB)

1994-11-01

This document presents design demonstrations conducted of liquid low-level waste (LLLW) storage tank systems located at the Oak Ridge National Laboratory (ORNL). Demonstration of the design of these tank systems has been stipulated by the Federal Facility Agreement (FFA) between the US Environmental Protection Agency (EPA)-Region IV; the Tennessee Department of Environment and Conservation (TDEC); and the DOE. The FFA establishes four categories of tanks. These are: Category A -- New or replacement tank systems with secondary containment; Category B -- Existing tank systems with secondary containment; Category C -- Existing tank systems without secondary containment; Category D -- Existing tank systems without secondary containment that are removed from service. This document provides a design demonstration of the secondary containment and ancillary equipment of 11 tank systems listed in the FFA as Category B. The design demonstration for each tank is presented.

Design demonstrations for category B tank systems at Oak Ridge National Laboratory, Oak Ridge, Tennessee

International Nuclear Information System (INIS)

1994-11-01

This document presents design demonstrations conducted of liquid low-level waste (LLLW) storage tank systems located at the Oak Ridge National Laboratory (ORNL). Demonstration of the design of these tank systems has been stipulated by the Federal Facility Agreement (FFA) between the US Environmental Protection Agency (EPA)-Region IV; the Tennessee Department of Environment and Conservation (TDEC); and the DOE. The FFA establishes four categories of tanks. These are: Category A -- New or replacement tank systems with secondary containment; Category B -- Existing tank systems with secondary containment; Category C -- Existing tank systems without secondary containment; Category D -- Existing tank systems without secondary containment that are removed from service. This document provides a design demonstration of the secondary containment and ancillary equipment of 11 tank systems listed in the FFA as Category B. The design demonstration for each tank is presented

Laser experimental system as teaching aid for demonstrating basic phenomena of laser feedback

International Nuclear Information System (INIS)

Xu, Ling; Zhao, Shijie; Zhang, Shulian

2015-01-01

An experimental laser teaching system is developed to demonstrate laser feedback phenomena, which bring great harm to optical communication and benefits to precision measurement. The system consists of an orthogonally polarized He-Ne laser, a feedback mirror which reflects the laser output light into the laser cavity, and an optical attenuator which changes the intensity of the feedback light. As the feedback mirror is driven by a piezoelectric ceramic, the attenuator is adjusted and the feedback mirror is tilted, the system can demonstrate many basic laser feedback phenomena, including weak, moderate and strong optical feedback, multiple feedback and polarization flipping. Demonstrations of these phenomena can give students a better understanding about the intensity and polarization of lasers. The system is well designed and assembled, simple to operate, and provides a valuable teaching aid at an undergraduate level. (paper)

Advanced Reactor Passive System Reliability Demonstration Analysis for an External Event

Directory of Open Access Journals (Sweden)

Matthew Bucknor

2017-03-01

Full Text Available Many advanced reactor designs rely on passive systems to fulfill safety functions during accident sequences. These systems depend heavily on boundary conditions to induce a motive force, meaning the system can fail to operate as intended because of deviations in boundary conditions, rather than as the result of physical failures. Furthermore, passive systems may operate in intermediate or degraded modes. These factors make passive system operation difficult to characterize within a traditional probabilistic framework that only recognizes discrete operating modes and does not allow for the explicit consideration of time-dependent boundary conditions. Argonne National Laboratory has been examining various methodologies for assessing passive system reliability within a probabilistic risk assessment for a station blackout event at an advanced small modular reactor. This paper provides an overview of a passive system reliability demonstration analysis for an external event. Considering an earthquake with the possibility of site flooding, the analysis focuses on the behavior of the passive Reactor Cavity Cooling System following potential physical damage and system flooding. The assessment approach seeks to combine mechanistic and simulation-based methods to leverage the benefits of the simulation-based approach without the need to substantially deviate from conventional probabilistic risk assessment techniques. Although this study is presented as only an example analysis, the results appear to demonstrate a high level of reliability of the Reactor Cavity Cooling System (and the reactor system in general for the postulated transient event.

Advanced reactor passive system reliability demonstration analysis for an external event

Energy Technology Data Exchange (ETDEWEB)

Bucknor, Matthew; Grabaskas, David; Brunett, Acacia J.; Grelle, Austin [Argonne National Laboratory, Argonne (United States)

2017-03-15

Many advanced reactor designs rely on passive systems to fulfill safety functions during accident sequences. These systems depend heavily on boundary conditions to induce a motive force, meaning the system can fail to operate as intended because of deviations in boundary conditions, rather than as the result of physical failures. Furthermore, passive systems may operate in intermediate or degraded modes. These factors make passive system operation difficult to characterize within a traditional probabilistic framework that only recognizes discrete operating modes and does not allow for the explicit consideration of time-dependent boundary conditions. Argonne National Laboratory has been examining various methodologies for assessing passive system reliability within a probabilistic risk assessment for a station blackout event at an advanced small modular reactor. This paper provides an overview of a passive system reliability demonstration analysis for an external event. Considering an earthquake with the possibility of site flooding, the analysis focuses on the behavior of the passive Reactor Cavity Cooling System following potential physical damage and system flooding. The assessment approach seeks to combine mechanistic and simulation-based methods to leverage the benefits of the simulation-based approach without the need to substantially deviate from conventional probabilistic risk assessment techniques. Although this study is presented as only an example analysis, the results appear to demonstrate a high level of reliability of the Reactor Cavity Cooling System (and the reactor system in general) for the postulated transient event.

Advanced reactor passive system reliability demonstration analysis for an external event

International Nuclear Information System (INIS)

Bucknor, Matthew; Grabaskas, David; Brunett, Acacia J.; Grelle, Austin

2017-01-01

Many advanced reactor designs rely on passive systems to fulfill safety functions during accident sequences. These systems depend heavily on boundary conditions to induce a motive force, meaning the system can fail to operate as intended because of deviations in boundary conditions, rather than as the result of physical failures. Furthermore, passive systems may operate in intermediate or degraded modes. These factors make passive system operation difficult to characterize within a traditional probabilistic framework that only recognizes discrete operating modes and does not allow for the explicit consideration of time-dependent boundary conditions. Argonne National Laboratory has been examining various methodologies for assessing passive system reliability within a probabilistic risk assessment for a station blackout event at an advanced small modular reactor. This paper provides an overview of a passive system reliability demonstration analysis for an external event. Considering an earthquake with the possibility of site flooding, the analysis focuses on the behavior of the passive Reactor Cavity Cooling System following potential physical damage and system flooding. The assessment approach seeks to combine mechanistic and simulation-based methods to leverage the benefits of the simulation-based approach without the need to substantially deviate from conventional probabilistic risk assessment techniques. Although this study is presented as only an example analysis, the results appear to demonstrate a high level of reliability of the Reactor Cavity Cooling System (and the reactor system in general) for the postulated transient event

An evaluation of harvesting machinery for short rotation coppice willow in Denmark

Energy Technology Data Exchange (ETDEWEB)

Kofman, P.D.; Spinelli, R.

1997-12-31

During the harvesting seasons 1994-1995 and 1995-1996 several harvesting trials were carried out within the EU project on harvesting and storage of Short Rotation Crops and within a national project. During this period the following machines were investigated: Diemelstadt poplar harvester, cut and chip; Claas forage harvester with SRF header, cut and chip; Austoft sugarcane harvester, adapted to SRF, cut and chip; Bender II, cut and chip; Hvidsted Energy Allrounder, whole shoot harvester; Dansalix whole shoot harvester. In the 1994-1995 season the intention was to harvest 300 tonnes of whole shoots, chunks and chips for a storage trial. The main conclusions of the 1994-1995 harvesting season must be that harvesting willow with the existing machines in wet winters without frozen ground is very difficult. The machines will have to be developed further and special interest should be given to developing shuttle vehicles with the same flotation as the tracked harvester. Several of the problems encountered with the machines in Denmark were confirmed by the experience in the other trials. Road transportation of chips from SRF plantations is just as expensive as transporting energy chips from the forest at about Dkr 50 per tonne over 48 km. Transporting whole shoots is very expensive due to the low bulk density. Transportation of whole shoots over 48 km costs on the average Dkr 133 per tonne fresh. A very short pilot study into chipping of whole shoots from a three metre high pile indicated that this comminution with a normal forest chipper has a low productivity (8.9 tonnes fresh per work place hour) and is very expensive at Dkr 157 per tonne. This productivity can be improved by equipping the chipper with a special feeding table and better feed rollers for the SRF crop. (EG)

A continuous hyperspatial monitoring system of evapotranspiration and gross primary productivity from Unmanned Aerial Systems

Science.gov (United States)

Wang, Sheng; Bandini, Filippo; Jakobsen, Jakob; Zarco-Tejada, Pablo J.; Köppl, Christian Josef; Haugård Olesen, Daniel; Ibrom, Andreas; Bauer-Gottwein, Peter; Garcia, Monica

2017-04-01

Unmanned Aerial Systems (UAS) can collect optical and thermal hyperspatial (challenges for an operational monitoring using UAS compared to satellites: the payload capacity of most commercial UAS is less than 2 kg, but miniaturized sensors have low signal to noise ratios and small field of view requires mosaicking hundreds of images and accurate orthorectification. In addition, wind gusts and lower platform stability require appropriate geometric and radiometric corrections. Finally, modeling fluxes on days without images is still an issue for both satellite and UAS applications. This study focuses on designing an operational UAS-based monitoring system including payload design, sensor calibration, based on routine collection of optical and thermal images in a Danish willow field to perform a joint monitoring of ET and GPP dynamics over continuous time at daily time steps. The payload (approach (Potter et al., 1993). Both models estimate ET and GPP under optimum potential conditions down-regulated by the same biophysical constraints dependent on remote sensing and atmospheric data to reflect multiple stresses. Vegetation indices were calculated from the multispectral data to assess vegetation conditions, while thermal infrared imagery was used to compute a thermal inertia index to infer soil moisture constraints. To interpolate radiometric temperature between flights, a prognostic Surface Energy Balance model (Margulis et al., 2001) based on the force-restore method was applied in a data assimilation scheme to obtain continuous ET and GPP fluxes. With this operational system, regular flight campaigns with a hexacopter (DJI S900) have been conducted in a Danish willow flux site (Risø) over the 2016 growing season. The observed energy, water and carbon fluxes from the Risø eddy covariance flux tower were used to validate the model simulation. This UAS monitoring system is suitable for agricultural management and land-atmosphere interaction studies.

Autonomous gas chromatograph system for Thermal Enhanced Vapor Extraction System (TEVES) proof of concept demonstration

International Nuclear Information System (INIS)

Peter, F.J.; Laguna, G.R.

1996-09-01

An autonomous gas chromatograph system was designed and built to support the Thermal Enhanced Vapor Extraction System (TEVES) demonstration. TEVES is a remediation demonstration that seeks to enhance an existing technology (vacuum extraction) by adding a new technology (soil heating). A pilot scale unit was set up at one of the organic waste disposal pits at the Sandia National Laboratories Chemical Waste Landfill (CWL) in Tech Area 3. The responsibility for engineering a major part of the process instrumentation for TEVES belonged to the Manufacturing Control Subsystems Department. The primary mission of the one-of-a-kind hardware/software system is to perform on-site gas sampling and analysis to quantify a variety of volatile organic compounds (VOCs) from various sources during TEVES operations. The secondary mission is to monitor a variety of TEVES process physical parameters such as extraction manifold temperature, pressure, humidity, and flow rate, and various subsurface pressures. The system began operation in September 1994 and was still in use on follow-on projects when this report was published

Development of a Terrestrial Modeling System: The China-wide Demonstration

Science.gov (United States)

Duan, Q.; Dai, Y.; Zheng, X.; Ye, A.; Chen, Z.; Shangguang, W.

2010-12-01

A terrestrial modeling system (TMS) is being developed at Beijing Normal University. The purposes of TMS are (1) to provide a land surface parameterization scheme fully capable of being coupled with and climate and Earth system models of different scales; (2) to provide a standalone platform for simulation and prediction of land surface processes; and (3) to provide a platform for studying human-Earth system interactions. This system will build on and extend existing capabilities at BNU, including the Common Land Model (CoLM) system, high-resolution atmospheric forcing data sets, high-resolution soil and vegetation data sets, and high-performance computing facilities and software. This presentation describes the system design and demonstrates the initial capabilities of TMS in simulating water and energy fluxes over the continental China for a multi-year period.

Design demonstrations for Category B tank systems piping at Oak Ridge National Laboratory, Oak Ridge, Tennessee

International Nuclear Information System (INIS)

1994-12-01

Demonstration of the design of the piping systems described in this report is stipulated by the Federal Facility Agreement (FFA) between the U.S. Environmental Protection Agency (EPA)-Region IV, the Tennessee Department of Environment and Conservation (TDEC), and the U.S. Department of Energy (DOE). This report provides a design demonstration of the secondary containment and ancillary equipment of 30 piping systems designated in the FFA as Category B (i.e., existing tank systems with secondary containment). Based on the findings of the Design Demonstrations for the Remaining 19 Category B Tank Systems, (DOE/OR/03-1150 ampersand D2), three tank systems originally designated as Category B have been redesignated as Category C (i.e., existing tank systems without secondary containment). The design demonstrations were developed using information obtained from design drawings (as-built when available), construction specifications, and interviews with facility operators. Each design demonstration addresses system conformance to the requirements of the FFA (Appendix F, Section C). Deficiencies or restrictions regarding the ability to demonstrate that each of the containment systems conforms to FFA requirements are noted in the discussion of each piping system and presented in Table 2.0-1

42 CFR 403.308 - State systems under demonstration projects-mandatory approval.

Science.gov (United States)

2010-10-01

... 42 Public Health 2 2010-10-01 2010-10-01 false State systems under demonstration projects..., DEPARTMENT OF HEALTH AND HUMAN SERVICES GENERAL PROVISIONS SPECIAL PROGRAMS AND PROJECTS Recognition of State... approval of a State system are met under § 403.304 (b)(1)-(10) and § 403.304(c), and, if appropriate § 403...

Field Demonstration of Fuel Crud Filtration System at Ulchin Plant

International Nuclear Information System (INIS)

Kang, Duk-Won; Lee, Doo-Ho; Park, Jong-Youl; Choi, In-Kyu

2007-01-01

Crud deposited onto the fuel assemblies in nuclear power plants was not a serious problem until an upper core flux depression named Axial Offset Anomaly (AOA) was found at Callaway, USA in 1989. Though the mechanism of an AOA is not completely understood, crud is believed to be a key component of initiating AOA. After the sufficient amount of corrosion products in the reactor cooling system are deposited on the fuel clad by a sub-cooled nucleate boiling, boron is adsorbed in the crud. Thus a measurable reduction in the neutron flux occurs which causes an AOA problem. A filtration system has been developed to remove the fuel crud from irradiated fuel assemblies for mitigating the axial offset anomaly under a technical cooperation agreement with DEI (Dominion Engineering Inc.). This filtration system with a fuel cleaning fixture was successfully demonstrated at Ulchin plant unit 2. Within several minutes, detachable crud deposits were effectively removed from the clad surfaces of the fuel assembly. Also, to characterize the crud particles for each fuel assembly, a small crud sampling device and radiation monitor devices were connected to the filtration system during the cleaning operation. In this study, we completed a functional test and demonstration of an ultrasonic fuel cleaning system by using four spent fuel assemblies. It took only 5 minutes to remove the fuel crud from each fuel assembly. In addition, collective dose rates indicated an average of 8 R/Hr per assembly

Flight Demonstration of X-33 Vehicle Health Management System Components on the F/A-18 Systems Research Aircraft

Science.gov (United States)

Schweikhard, Keith A.; Richards, W. Lance; Theisen, John; Mouyos, William; Garbos, Raymond

2001-01-01

The X-33 reusable launch vehicle demonstrator has identified the need to implement a vehicle health monitoring system that can acquire data that monitors system health and performance. Sanders, a Lockheed Martin Company, has designed and developed a COTS-based open architecture system that implements a number of technologies that have not been previously used in a flight environment. NASA Dryden Flight Research Center and Sanders teamed to demonstrate that the distributed remote health nodes, fiber optic distributed strain sensor, and fiber distributed data interface communications components of the X-33 vehicle health management (VHM) system could be successfully integrated and flown on a NASA F-18 aircraft. This paper briefly describes components of X-33 VHM architecture flown at Dryden and summarizes the integration and flight demonstration of these X-33 VHM components. Finally, it presents early results from the integration and flight efforts.

Design demonstrations for Category B tank system piping at Oak Ridge National Laboratory, Oak Ridge, Tennessee

International Nuclear Information System (INIS)

1994-02-01

Demonstration of the design of the tank systems described in this report is stipulated by the Federal Facility Agreement (FFA) between the U.S. Environmental Protection Agency-Region IV, the Tennessee Department of Environment and Conservation, and the U.S. Department of Energy. This report provides a design demonstration of the secondary containment and ancillary equipment of 30 piping systems listed in the FFA as Category B (i.e., existing tank systems with secondary containment). The design demonstrations were developed using information obtained from design drawings (as-built when available), construction specifications, and interviews with facility operators. Each design demonstration addresses system conformance to the requirements of the FFA (Appendix F, Section C). Deficiencies or restrictions regarding the ability to demonstrate that each of the containment systems conforms to FFA requirements are noted in the discussion of each piping system

Design demonstrations for Category B tank systems at Oak Ridge National Laboratory, Oak Ridge, Tennessee

International Nuclear Information System (INIS)

1992-07-01

This document presents design demonstrations conducted of liquid low-level waste (LLLW) storage tank systems located at the Oak Ridge National Laboratory (ORNL). ORNL has conducted research in energy related fields since 1943. The facilities used to conduct the research include nuclear reactors, chemical pilot plants, research laboratories, radioisotope production laboratories, and support facilities. These facilities have produced a variety of radioactive and/or hazardous wastes. These wastes have been stored and transported through an extensive network of piping and tankage. Demonstration of the design of these tank systems has been stipulated by the Federal Facility Agreement (FFA) between the US Environmental Protection Agency (EPA) - Region IV; the Tennessee Department of Environment and Conservation (TDEC); and the DOE. The FFA establishes four categories of tanks. These are: Category A -- New or Replacement Tank Systems with Secondary Containment; Category B -- Existing Tank Systems with Secondary Containment; Category C -- Existing Tank Systems without Secondary Containment; and Category D -- Existing Tank Systems without Secondary Containment that are; Removed from Service. This document provides a design demonstration of the secondary containment and ancillary equipment of 11 tank systems listed in the FFA as Category ''B.'' The design demonstration for each tank is presented in Section 2. The design demonstrations were developed using information obtained from the design drawings (as-built when available), construction specifications, and interviews with facility operators. The assessments assume that each tank system was constructed in accordance with the design drawings and construction specifications for that system unless specified otherwise. Each design demonstration addresses system conformance to the requirements of the FFA (Appendix F, Subsection C)

Demonstration of a Variable Phase Turbine Power System for Low Temperature Geothermal Resources

Energy Technology Data Exchange (ETDEWEB)

Hays, Lance G

2014-07-07

A variable phase turbine assembly will be designed and manufactured having a turbine, operable with transcritical, two-phase or vapor flow, and a generator – on the same shaft supported by process lubricated bearings. The assembly will be hermetically sealed and the generator cooled by the refrigerant. A compact plate-fin heat exchanger or tube and shell heat exchanger will be used to transfer heat from the geothermal fluid to the refrigerant. The demonstration turbine will be operated separately with two-phase flow and with vapor flow to demonstrate performance and applicability to the entire range of low temperature geothermal resources. The vapor leaving the turbine is condensed in a plate-fin refrigerant condenser. The heat exchanger, variable phase turbine assembly and condenser are all mounted on single skids to enable factory assembly and checkout and minimize installation costs. The system will be demonstrated using low temperature (237F) well flow from an existing large geothermal field. The net power generated, 1 megawatt, will be fed into the existing power system at the demonstration site. The system will demonstrate reliable generation of inexpensive power from low temperature resources. The system will be designed for mass manufacturing and factory assembly and should cost less than $1,200/kWe installed, when manufactured in large quantities. The estimated cost of power for 300F resources is predicted to be less than 5 cents/kWh. This should enable a substantial increase in power generated from low temperature geothermal resources.

Demonstration of Hadoop-GIS: A Spatial Data Warehousing System Over MapReduce.

Science.gov (United States)

Aji, Ablimit; Sun, Xiling; Vo, Hoang; Liu, Qioaling; Lee, Rubao; Zhang, Xiaodong; Saltz, Joel; Wang, Fusheng

2013-11-01

The proliferation of GPS-enabled devices, and the rapid improvement of scientific instruments have resulted in massive amounts of spatial data in the last decade. Support of high performance spatial queries on large volumes data has become increasingly important in numerous fields, which requires a scalable and efficient spatial data warehousing solution as existing approaches exhibit scalability limitations and efficiency bottlenecks for large scale spatial applications. In this demonstration, we present Hadoop-GIS - a scalable and high performance spatial query system over MapReduce. Hadoop-GIS provides an efficient spatial query engine to process spatial queries, data and space based partitioning, and query pipelines that parallelize queries implicitly on MapReduce. Hadoop-GIS also provides an expressive, SQL-like spatial query language for workload specification. We will demonstrate how spatial queries are expressed in spatially extended SQL queries, and submitted through a command line/web interface for execution. Parallel to our system demonstration, we explain the system architecture and details on how queries are translated to MapReduce operators, optimized, and executed on Hadoop. In addition, we will showcase how the system can be used to support two representative real world use cases: large scale pathology analytical imaging, and geo-spatial data warehousing.

Environmental Measurement-While-Drilling System and Horizontal Directional Drilling Technology Demonstration, Hanford Site

International Nuclear Information System (INIS)

Williams, C.V.; Lockwood, G.J.; Normann, R.A.; Myers, D.A.; Gardner, M.G.; Williamson, T.; Huffman, J.

1999-01-01

The Environmental Measurement-While-Drilling (EMWD) system and Horizontal Directional Drilling (HDD) were successfully demonstrated at the Mock Tank Leak Simulation Site and the Drilling Technology Test Site, Hanford, Washington. The use of directional drilling offers an alternative to vertical drilling site characterization. Directional drilling can develop a borehole under a structure, such as a waste tank, from an angled entry and leveling off to horizontal at the desired depth. The EMWD system represents an innovative blend of new and existing technology that provides the capability of producing real-time environmental and drill bit data during drilling operations. The technology demonstration consisted of the development of one borehole under a mock waste tank at a depth of approximately minus8 m (minus27 ft.), following a predetermined drill path, tracking the drill path to within a radius of approximately1.5 m (5 ft.), and monitoring for zones of radiological activity using the EMWD system. The purpose of the second borehole was to demonstrate the capability of drilling to a depth of ∼ -21 m (-70 ft.), the depth needed to obtain access under the Hanford waste tanks, and continue drilling horizontally. This report presents information on the HDD and EMWD technologies, demonstration design, results of the demonstrations, and lessons learned

Fiscal 1995 survey report on the environmentally friendly type coal utilization system joint demonstration project. Water-saving coal preparation system joint demonstration project; Kankyo chowagata sekitan riyo system kyodo jissho jigyo. Shosuigata sentan system kyodo jissho jigyo

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

This project makes demonstration of clean coal technology (CCT) in China and preparation for the base of its spread, controlled environmental pollution due to the coal use by the countries concerned, and contributes to stably secure energy of Japan. The paper made analog operation in the 1960s-1970s, supported by Russia and Poland, introduced two computer systems for operational control and quality control, densimeter, level meter, flow meter and analyzer to coal preparation plants having problems on productivity and quality control, made the optimum operational diagnosis for the plants, and at the same time, demonstrated the comprehensive rehabilitation type system by which water saving, high quality and high effectiveness are obtained. Various types of sensors such as rapid ash meter, scale and densitometer and computers are introduced to coal preparation plants which were recently constructed in China, have jig or heavy liquid cyclone as main preparation equipment and conducts operational control. There, the central control system was demonstrated in which various information collected in the central operation room and in-site equipment is combined by network for high-grade data processing and water saving is achieved. 50 figs., 11 tabs.

Phytoextraction of soil trace elements by willow during a phytoremediation trial in Southern Québec, Canada.

Science.gov (United States)

Courchesne, François; Turmel, Marie-Claude; Cloutier-Hurteau, Benoît; Constantineau, Simon; Munro, Lara; Labrecque, Michel

2017-06-03

The phytoextraction of the trace elements (TEs) As, Cd, Cu, Ni, Pb, and Zn by willow cultivars (Fish Creek, SV1 and SX67) was measured during a 3-year field trial in a mildly contaminated soil. Biomass ranged from 2.8 to 4.4 Mg/ha/year at 30,000 plants/ha. Shoots (62%) were the main component followed by leaves (23%) and roots (15%). Biomass was positively linked to soluble soil dissolved organic carbon, K, and Mg, while TEs, not Cd and Zn, had a negative effect. The TE concentration ranking was: Zn > Cu > Cd > Ni, Pb > As, and distribution patterns were: (i) minima in shoots (As, Ni), (ii) maxima in leaves (Cd, Zn), or (iii) maxima in roots (Cu, Pb). Correlations between soil and plant TE were significant for the six TEs in roots. The amounts extracted were at a maximum for Zn, whereas Fish Creek and SV1 extracted more TE than SX67. More than 60% (91-94% for Cd and Zn) of the total TE was in the aboveground parts. Uptake increased with time because of higher biomass. Fertilization, the selection of cultivars, and the use of complementary plants are required to improve productivity and Cd and Zn uptake.

Radioactive waste incineration system cold demonstration test, (2)

Energy Technology Data Exchange (ETDEWEB)

Hozumi, Masahiro; Seike, Yasuhiko; Takaoku, Yoshinobu; Yamanaka, Yasuhiro; Asahara, Masaharu; Katagiri, Keishi; Matsumoto, Kenji; Nagae, Madoka

1985-12-01

It is urgently necessary to solve the radioactive waste problem. As an effective means for the volume reduction of low-level radioactive wastes, an improved incineration system is greatly required. SHI's Waste Incineration (WIS) licensed by Combustion Engineering, Inc., has the significant advantage of processing a variety of wastes. We started a cold demonstration test in April, 1984 to verify the excellent performance of WIS. The test was successfully completed in September, 1985 with the record of more than 1000 hours of incineration testing time. In the present paper, we describe the test results during one and half years of test period.

Potent clones. Efficiency of phytoremediation by means of willow family on the status of heavy metals; Potente Klone. Wirkung der Phytoremediation mittels Weidengewaechsen auf den Schwermetallstatus

Energy Technology Data Exchange (ETDEWEB)

Fibian, Kurt D. [Rostock Univ. (Germany). Fachgebiet Pflanzenernaehrung; Gombler, Willy; Gruessing, Edgar; Janssen-Weets, Sybille; Schlaak, Michael [Fachhochschule Emden-Leer, Emden (Germany). Inst. fuer Umwelttechnik-EUTEC

2010-11-15

The contents of cadmium, copper and zinc in a polluted substrate (harbour silt) were determined by means of fractionated extraction. In a pot attempt, four willow clones were cultivated on this substrate. After a test period of three years the changes in the individual fractions of heavy metal were determined. At the same time, the remove capacity of the test pastures being relevant for the process of phytoextraction were determined by means of the content of heavy metals of the aboveground plant organs and its dry weight. The results show that two of the examined pasture clones clearly are better suitable than poplars and corn, in order to remove in particular cadmium and zinc from the soil by means of phytoremediation.

Using a remote sensing/GIS model to predict southwestern Willow Flycatcher breeding habitat along the Rio Grande, New Mexico

Science.gov (United States)

Hatten, James R.; Sogge, Mark K.

2007-01-01

Introduction The Southwestern Willow Flycatcher (Empidonax traillii extimus; hereafter SWFL) is a federally endangered bird (USFWS 1995) that breeds in riparian areas in portions of New Mexico, Arizona, southwestern Colorado, extreme southern Utah and Nevada, and southern California (USFWS 2002). Across this range, it uses a variety of plant species as nesting/breeding habitat, but in all cases prefers sites with dense vegetation, high canopy, and proximity to surface water or saturated soils (Sogge and Marshall 2000). As of 2005, the known rangewide breeding population of SWFLs was roughly 1,214 territories, with approximately 393 territories distributed among 36 sites in New Mexico (Durst et al. 2006), primarily along the Rio Grande. One of the key challenges facing the management and conservation of the Southwestern Willow Flycatcher is that riparian areas are dynamic, with individual habitat patches subject to cycles of creation, growth, and loss due to drought, flooding, fire, and other disturbances. Former breeding patches can lose suitability, and new habitat can develop within a matter of only a few years, especially in reservoir drawdown zones. Therefore, measuring and predicting flycatcher habitat - either to discover areas that might support SWFLs, or to identify areas that may develop into appropriate habitat - requires knowledge of recent/current habitat conditions and an understanding of the factors that determine flycatcher use of riparian breeding sites. In the past, much of the determination of whether a riparian site is likely to support breeding flycatchers has been based on qualitative criteria (for example, 'dense vegetation' or 'large patches'). These determinations often require on-the-ground field evaluations by local or regional SWFL experts. While this has proven valuable in locating many of the currently known breeding sites, it is difficult or impossible to apply this approach effectively over large geographic areas (for example, the

BILLIARDS: Baseline Instrumented Lithology Lander, Inspector and Asteroid Redirection Demonstration System

Science.gov (United States)

Marcus, Matthew; Sloane, Joshua; Ortiz, Oliver; Barbee, Brent

2015-01-01

BILLIARDS Baseline Instrumented Lithology Lander, Inspector, and Asteroid Redirection Demonstration System Proposed demonstration mission for Billiard-Ball concept Select asteroid pair with natural close approach to minimize cost and complexity Primary Objectives Rendezvous with a small (10m), near Earth (alpha) asteroid Maneuver the alpha asteroid to a collision with a 100m (beta) asteroid Produce a detectable deflection or disruption of the beta asteroid Secondary objectives Contribute knowledge of asteroid composition and characteristics Contribute knowledge of small-body formation Opportunity for international collaboration

Out-of-pile demonstration test of hydrogen production system coupling with HTTR

International Nuclear Information System (INIS)

Inagaki, Yoshiyuki; Nishihara, Tetsuo; Takeda, Tetsuaki; Hada, Kazuhiko; Hayashi, Koji

1999-01-01

In Japan Atomic Energy Research Institute, a hydrogen production system is being designed to produce hydrogen by means of a steam reforming process of natural gas using nuclear heat (10 MW, 905degC) supplied by the High Temperature Engineering Test Reactor (HTTR). The safety principle and criteria are also being investigated in the HTTR hydrogen production system. Prior to coupling of the steam reforming system with the HTTR, an out-of-pile demonstration test was planned to confirm safety, controllability and performance of the steam reforming system under simulated operational conditions of the HTTR hydrogen production system. The out-of-pile test facility simulates key components downstream an intermediate heat exchanger of the HTTR hydrogen production system on a scale of 1 to 30 has a hydrogen production capacity of 110 Nm 3 /h using an electric heater as a reactor substitute. The test facility is under manufacturing aiming at completion in 2000 and followed by the test till 2004. In parallel to this, a hydrogen permeation test and a corrosion test of a catalyst tube of a steam reformer are being carried out to obtain data necessary for the design of the system. This report describes outline of the out-of-pile hydrogen production facility and demonstration test program for the HTTR hydrogen production system at present status. (author)

Out-of-pile demonstration test of hydrogen production system coupling with HTTR

Energy Technology Data Exchange (ETDEWEB)

Inagaki, Yoshiyuki; Nishihara, Tetsuo; Takeda, Tetsuaki; Hada, Kazuhiko; Hayashi, Koji [Japan Atomic Energy Research Inst., Oarai, Ibaraki (Japan). Oarai Research Establishment

1999-07-01

In Japan Atomic Energy Research Institute, a hydrogen production system is being designed to produce hydrogen by means of a steam reforming process of natural gas using nuclear heat (10 MW, 905degC) supplied by the High Temperature Engineering Test Reactor (HTTR). The safety principle and criteria are also being investigated in the HTTR hydrogen production system. Prior to coupling of the steam reforming system with the HTTR, an out-of-pile demonstration test was planned to confirm safety, controllability and performance of the steam reforming system under simulated operational conditions of the HTTR hydrogen production system. The out-of-pile test facility simulates key components downstream an intermediate heat exchanger of the HTTR hydrogen production system on a scale of 1 to 30 has a hydrogen production capacity of 110 Nm{sup 3}/h using an electric heater as a reactor substitute. The test facility is under manufacturing aiming at completion in 2000 and followed by the test till 2004. In parallel to this, a hydrogen permeation test and a corrosion test of a catalyst tube of a steam reformer are being carried out to obtain data necessary for the design of the system. This report describes outline of the out-of-pile hydrogen production facility and demonstration test program for the HTTR hydrogen production system at present status. (author)

Willow bioenergy plantation research in the Northeast

Energy Technology Data Exchange (ETDEWEB)

White, E.H.; Abrahamson, L.P.; Kopp, R.F. [SUNY College of Environmental Science and Forestry, Syracuse, NY (United States); Nowak, C.A. [USDA Forest Service, Warren, PA (United States)

1993-12-31

Experiments were established in Central New York in the spring of 1987 to evaluate the potential of Salix for biomass production in bioenergy plantations. Emphasis of the research was on developing and refining establishment, tending and maintenance techniques, with complimentary study of breeding, coppice physiology, pests, nutrient use and bioconversion to energy products. Current yields utilizing salix clones developed in cooperation with the University of Toronto in short-rotation intensive culture bioenergy plantations in the Northeast approximate 8 oven dry tons per acre per year with annual harvesting. Successful clones have been identified and culture techniques refined. The results are now being integrated to establish a 100 acre Salix large-scale bioenergy farm to demonstrate current successful biomass production technology and to provide plantations of sufficient size to test harvesters; adequately assess economics of the systems; and provide large quantities of uniform biomass for pilot-scale conversion facilities.

Demonstration personnel and material tracking system at ANL-W

International Nuclear Information System (INIS)

Roybal, J.A.; Ortiz, S.; Henslee, S.P.

1988-01-01

A Personnel and Material Tracking System (PMTS) was demonstrated in the Fuel Manufacturing Facility (FMF) at Argonne National Laboratories-West (ANL-W) in July, 1987. The PMTS is intended to aid in the transfer of inventory materials from area to area within a facility such as FMF. It is also intended to assure that only those personnel who are authorized to do so may conduct these transfer operations. The PMTS Personnel Movement (PM) subsystem uses portals installed between areas to alert the system to the movement of personnel between areas. The portals are composed to two sensors, one on either side of a proximity badge reader, to detect the presence of personnel entering the portal area. However, a restricted area can be assigned to any badge holder which will cause the system to issue an alert if the badge holder passes into his/her restricted area. The PM subsystem is intended to be transparent when in use. The PMTS Inventory Material Access (IMA) subsystem provides two functions: material control and material access. The material control is provided by the Wireless Alarm Transmission of Container Handling (WATCH) system which is a sensor rf transmitter system that detects item movements. Material access is provided by the Mobile Accountability Verification Inventory Station (MAVIS) system which is a self-powered smart barcode reader

Managing Risk on a Technology Development Project/Advanced Mirror System Demonstrator

Science.gov (United States)

Byberg, Alicia; Russell, J. Kevin; Stahl, Phil (Technical Monitor)

2002-01-01

The risk management study applied to the Advanced Mirror System Demonstrator (AMSD), a precursor mirror technology development for the Next Generation Space Telescope (NGST) is documented. The AMSD will be developed as a segment of a lightweight primary mirror system that can be produced at a low cost and with a short manufacturing schedule. The technology gained from the program will support the risk mitigation strategy for the NGST, as well as other government agency space mirror programs.

Swedish-Estonian energy forest research cooperation

International Nuclear Information System (INIS)

Ross, J.; Kirt, E.; Koppel, A.; Kull, K.; Noormets, A.; Roostalu, H.; Ross, V.; Ross, M.

1996-01-01

The Organization of Estonian energetic economy is aimed at cutting the usage of oil, gas and coal and increasing the local resources firewood, oil-shale and peat for fuel. The resources of low-valued firewood-brushwood, fallen deadwood etc. are available during the following 10-15 years, but in the future the cultivation of energy forest (willow) plantations will be actual. During the last 20 years the Swedish scientists have been extensively studying the willow forest selection, cultivation and use in energetics and waste water purification systems. A Swedish-Estonian energy forest research project was started in 1993 between the Swedish Agricultural University on one hand and Toravere Observatory, Institute of Zoology and Botany, Estonian Academy of Sciences and Estonian Potato Processing Association on the other hand. In spring 5 willow plantations were established with the help of Swedish colleagues and obtained from Sweden 36000 willow cuttings. The aim of the project: a) To study experimentally and by means of mathematical modelling the biogeophysical aspects of growth and productivity of willow plantations in Sweden and Estonian climatological conditions. b) To study the possibility of using the willow plantations in waste waters purification. c) To study the economical efficiency of energy forest as an energy resource under the economic and environmental conditions of Estonia. d) To study the economic efficiency of willow plantations as a raw material for the basket industry in Estonia. e) To select the most productive and least vulnerable willow clones for practical application in energy plantations. During 1993 in all five plantations detailed analysis of soil properties has been carried out. In the plantation at Toravere Observatory phytometrical measurements were carried out - the growth of plant biomass leaf and stem area, vertical distribution of dry matter content, biomass and phyto area separately for leaves and stems has been performed. Some

Demonstration (DEMO) of Radio Frequency Identification (RFID) system for tracking and monitoring of nuclear materials.

Energy Technology Data Exchange (ETDEWEB)

Tsai, H. C.; Chen, K.; Liu, Y. Y.; Shuler, J. (Decision and Information Sciences); (USDOE)

2010-01-01

The US Department of Energy (DOE) [Environmental Management (EM), Office of Packaging and Transportation (EM-45)] Packaging Certification Program (PCP) has developed a radiofrequency identification (RFID) tracking and monitoring system for the management of nuclear materials packages during storage and transportation. The system, developed by the PCP team at Argonne National Laboratory, involves hardware modification, application software development, secured database and web server development, and irradiation experiments. In April 2008, Argonne tested key features of the RFID tracking and monitoring system in a weeklong, 1700 mile (2736 km) demonstration employing 14 empty type B fissile material drums of three designs (models 9975, 9977 and ES-3100) that have been certified for shipment by the DOE and the US Nuclear Regulatory Commission. The demonstration successfully integrated global positioning system (GPS) technology for vehicle tracking, satellite/cellular (general packet radio service, or GPRS) technologies for wireless communication, and active RFID tags with multiple sensors (seal integrity, shock, temperature, humidity and battery status) on drums. In addition, the demonstration integrated geographic information system (GIS) technology with automatic alarm notifications of incidents and generated buffer zone reports for emergency response and management of staged incidents. The demonstration was sponsored by EM and the US National Nuclear Security Administration, with the participation of Argonne, Savannah River and Oak Ridge National Laboratories. Over 50 authorised stakeholders across the country observed the demonstration via secured Internet access. The DOE PCP and national laboratories are working on several RFID system implementation projects at selected DOE sites, as well as continuing device and systems development and widening applications beyond DOE sites and possibly beyond nuclear materials to include other radioactive materials.

Demonstration (DEMO) of Radio Frequency Identification (RFID) system for tracking and monitoring of nuclear materials

International Nuclear Information System (INIS)

Tsai, H.C.; Chen, K.; Liu, Y.Y.; Shuler, J.

2010-01-01

The US Department of Energy (DOE) (Environmental Management (EM), Office of Packaging and Transportation (EM-45)) Packaging Certification Program (PCP) has developed a radiofrequency identification (RFID) tracking and monitoring system for the management of nuclear materials packages during storage and transportation. The system, developed by the PCP team at Argonne National Laboratory, involves hardware modification, application software development, secured database and web server development, and irradiation experiments. In April 2008, Argonne tested key features of the RFID tracking and monitoring system in a weeklong, 1700 mile (2736 km) demonstration employing 14 empty type B fissile material drums of three designs (models 9975, 9977 and ES-3100) that have been certified for shipment by the DOE and the US Nuclear Regulatory Commission. The demonstration successfully integrated global positioning system (GPS) technology for vehicle tracking, satellite/cellular (general packet radio service, or GPRS) technologies for wireless communication, and active RFID tags with multiple sensors (seal integrity, shock, temperature, humidity and battery status) on drums. In addition, the demonstration integrated geographic information system (GIS) technology with automatic alarm notifications of incidents and generated buffer zone reports for emergency response and management of staged incidents. The demonstration was sponsored by EM and the US National Nuclear Security Administration, with the participation of Argonne, Savannah River and Oak Ridge National Laboratories. Over 50 authorised stakeholders across the country observed the demonstration via secured Internet access. The DOE PCP and national laboratories are working on several RFID system implementation projects at selected DOE sites, as well as continuing device and systems development and widening applications beyond DOE sites and possibly beyond nuclear materials to include other radioactive materials.

Frost related dieback in Estonian energy plantations of willows in relation to fertilisation and pathogenic bacteria

Energy Technology Data Exchange (ETDEWEB)

Cambours, M.A.; Nejad, P. [Department of Forest Mycology and Pathology, Swedish University of Agricultural Sciences, Box 7026, 750 07 Uppsala (Sweden); Heinsoo, K. [Institute of Zoology and Botany, Estonian Agricultural University, Riia 181, 51014 Tartu (Estonia); Granhall, U. [Department of Microbiology, Swedish University of Agricultural Sciences, Box 7025, 750 07 Uppsala (Sweden)

2006-03-15

Two 9-year old Estonian Salix plantations suffering from dieback were studied: one situated on poor mineral soil and divided into fertilised and unfertilised plots (Saare plantation) and another growing on a well-decomposed and nitrogen-rich organic soil, without fertiliser application (Kambja plantation). Bacteria from internal tissues of visually damaged shoots from seven clones were isolated in spring and autumn. The strains were subsequently biochemically characterised and tested for ice nucleation activity and pathogenicity on Salix. Some strains were also analysed with 16S rRNA. High numbers of culturable bacteria were found, belonging mainly to Erwinia, Sphingomonas, Pseudomonas and Xanthomonas spp. Fertilised plots were significantly more colonised by bacteria than unfertilised plots and also more extensively damaged, showing a lower density of living plants after 7 years of culture. More ice nucleation active (INA) strains were found in Saare fertilised plots and at Kambja than in Saare unfertilised plots. Likewise, most pathogenic strains were isolated from Saare fertilised plots and from Kambja. For some of the willow clones studied, dieback appeared to be related to both clonal frost sensitivity and abundance of INA and pathogenic bacteria. The plantations probably suffered from the presence of high amounts of pathogens and from frost related injuries aggravated by INA bacteria. Most probably the fertilisation at Saare and the nitrogen-rich soil at Kambja created a favourable environment for bacterial development and led to high dieback levels after the first harvest. (author)

The development of the human exploration demonstration project (HEDP), a planetary systems testbed

Science.gov (United States)

Chevers, Edward S.; Korsmeyer, David J.

1993-01-01

The Human Exploration Demonstration Project (HEDP) is an ongoing task at the National Aeronautics and Space Administration's Ames Research Center to address the advanced technology requirements necessary to implement an integrated working and living environment for a planetary surface habitat. The integrated environment will consist of life support systems, physiological monitoring of project crew, a virtual environment workstation, and centralized data acquisition and habitat systems health monitoring. There will be several robotic systems on a simulated planetary landscape external to the habitat environment to provide representative work loads for the crew. This paper describes the status of the HEDP after one year, the major facilities composing the HEDP, the project's role as an Ames Research Center testbed, and the types of demonstration scenarios that will be run to showcase the technologies.

Design demonstrations for the remaining 19 Category B tank systems at Oak Ridge National Laboratory, Oak Ridge, Tennessee

International Nuclear Information System (INIS)

1995-01-01

This document presents design demonstrations conducted of liquid low-level waste (LLLW) storage tank systems located at the Oak Ridge National Laboratory (ORNL). Demonstration of the design of these tank systems has been stipulated by the Federal Facility Agreement (FFA) between the US Environmental Protection Agency (EPA)--Region IV; the Tennessee Department of Environment and Conservation (TDEC); and the DOE. The FFA establishes four categories of tank systems: Category A--New or Replacement Tank Systems with Secondary Containment; Category B--Existing Tank Systems with Secondary Containment; Category C--Existing Tank Systems Without Secondary Containment; and Category D--Existing Tank Systems Without Secondary Containment That are Removed from Service. This document provides a design demonstration of the secondary containment and ancillary equipment of 19 tank systems listed in the FFA as Category B. Three tank systems originally designated as Category B have been redesignated as Category C and one tank system originally designated as Category B has been redesignated as Category D. The design demonstration for each tank is presented in Section 2. The design demonstrations were developed using information obtained from the design drawings (as-built when available), construction specifications, and interviews with facility operators. The assessments assume that each tank system was constructed in accordance with the design drawings and construction specifications for that system unless specified otherwise. Each design demonstration addresses system conformance to the requirements of the FFA

Parasitism, productivity, and population growth: response of Least Bell's Vireos (Vireo bellii pusillus) and Southwestern Willow Flycatchers (Empidonax traillii extimus) to cowbird (Molothrus spp.) control

Science.gov (United States)

Kus, Barbara E.; Whitfield, Mary J.

2005-01-01

Cowbird (Molothrus spp.) control is a major focus of recovery-oriented management of two endangered riparian bird species,the Least Bell's Vireo (Vireo bellii pusillus) and Southwestern Willow Flycatcher (Empidonax traillii extimus). During the past 20 years, annual trapping of cowbirds at Least Bell's Vireo and Southwestern Willow Flycatcher breeding sites has eliminated or reduced parasitism in comparison with pretrapping rates and, thereby, significantly increased seasonal productivity of nesting pairs. Enhanced productivity, in turn, has resulted in an 8-fold increase in numbers of Least Bell's Vireos; Southwestern Willow Flycatcher abundance, however, has changed little, and at some sites has declined despite cowbird control. Although generally successful by these short-term measures of host population response, cowbird control poses potential negative consequences for long-term recovery of endangered species. As currently employed, cowbird control lacks predetermined biological criteria to trigger an end to the control, making these species' dependence on human intervention open-ended. Prolonged reliance on cowbird control to manage endangered species can shift attention from identifying and managing other factors that limit populations--in particular, habitat availability. On the basis of our analysis of these long-term programs, we suggest that cowbird control be reserved for short-term crisis management and be replaced, when appropriate, by practices emphasizing restoration and maintenance of natural processes on which species depend. /// El manejo orientado hacia la recuperación de dos especies de aves ribereñas Vireo belli pusillus y Empidonax trailli extimus se ha focalizado principalmente en el control de los Molothrus spp parásitos. Durante los pasados 20 años, la captura anual de los Molothrus en las áreas de nidificación de Vireo belli pusillus y Empidonax trailli extimus ha eliminado o reducido el parasitismo en comparación con las tasas

Botanical Extracts from Rosehip (Rosa canina), Willow Bark (Salix alba), and Nettle Leaf (Urtica dioica) Suppress IL-1β-Induced NF-κB Activation in Canine Articular Chondrocytes

Science.gov (United States)

Shakibaei, Mehdi; Allaway, David; Nebrich, Simone; Mobasheri, Ali

2012-01-01

The aim of this study was to characterize the anti-inflammatory mode of action of botanical extracts from rosehip (Rosa canina), willow bark (Salix alba), and nettle leaf (Urtica dioica) in an in vitro model of primary canine articular chondrocytes. Methods. The biological effects of the botanical extracts were studied in chondrocytes treated with IL-1β for up to 72 h. Expression of collagen type II, cartilage-specific proteoglycan (CSPG), β1-integrin, SOX-9, COX-2, and MMP-9 and MMP-13 was examined by western blotting. Results. The botanical extracts suppressed IL-1β-induced NF-κB activation by inhibition of IκBα phosphorylation, IκBα degradation, p65 phosphorylation, and p65 nuclear translocation. These events correlated with downregulation of NF-κB targets including COX-2 and MMPs. The extracts also reversed the IL-1β-induced downregulation of collagen type II, CSPG, β1-integrin, and cartilage-specific transcription factor SOX-9 protein expression. In high-density cultures botanical extracts stimulated new cartilage formation even in the presence of IL-1β. Conclusions. Botanical extracts exerted anti-inflammatory and anabolic effects on chondrocytes. The observed reduction of IL-1β-induced NF-κB activation suggests that further studies are warranted to demonstrate the effectiveness of plant extracts in the treatment of OA and other conditions in which NF-κB plays pathophysiological roles. PMID:22474508

Botanical Extracts from Rosehip (Rosa canina), Willow Bark (Salix alba), and Nettle Leaf (Urtica dioica) Suppress IL-1β-Induced NF-κB Activation in Canine Articular Chondrocytes.

Science.gov (United States)

Shakibaei, Mehdi; Allaway, David; Nebrich, Simone; Mobasheri, Ali

2012-01-01

The aim of this study was to characterize the anti-inflammatory mode of action of botanical extracts from rosehip (Rosa canina), willow bark (Salix alba), and nettle leaf (Urtica dioica) in an in vitro model of primary canine articular chondrocytes. Methods. The biological effects of the botanical extracts were studied in chondrocytes treated with IL-1β for up to 72 h. Expression of collagen type II, cartilage-specific proteoglycan (CSPG), β1-integrin, SOX-9, COX-2, and MMP-9 and MMP-13 was examined by western blotting. Results. The botanical extracts suppressed IL-1β-induced NF-κB activation by inhibition of IκBα phosphorylation, IκBα degradation, p65 phosphorylation, and p65 nuclear translocation. These events correlated with downregulation of NF-κB targets including COX-2 and MMPs. The extracts also reversed the IL-1β-induced downregulation of collagen type II, CSPG, β1-integrin, and cartilage-specific transcription factor SOX-9 protein expression. In high-density cultures botanical extracts stimulated new cartilage formation even in the presence of IL-1β. Conclusions. Botanical extracts exerted anti-inflammatory and anabolic effects on chondrocytes. The observed reduction of IL-1β-induced NF-κB activation suggests that further studies are warranted to demonstrate the effectiveness of plant extracts in the treatment of OA and other conditions in which NF-κB plays pathophysiological roles.

Botanical Extracts from Rosehip (Rosa canina, Willow Bark (Salix alba, and Nettle Leaf (Urtica dioica Suppress IL-1β-Induced NF-κB Activation in Canine Articular Chondrocytes

Directory of Open Access Journals (Sweden)

Mehdi Shakibaei

2012-01-01

Full Text Available The aim of this study was to characterize the anti-inflammatory mode of action of botanical extracts from rosehip (Rosa canina, willow bark (Salix alba, and nettle leaf (Urtica dioica in an in vitro model of primary canine articular chondrocytes. Methods. The biological effects of the botanical extracts were studied in chondrocytes treated with IL-1β for up to 72 h. Expression of collagen type II, cartilage-specific proteoglycan (CSPG, β1-integrin, SOX-9, COX-2, and MMP-9 and MMP-13 was examined by western blotting. Results. The botanical extracts suppressed IL-1β-induced NF-κB activation by inhibition of IκBα phosphorylation, IκBα degradation, p65 phosphorylation, and p65 nuclear translocation. These events correlated with downregulation of NF-κB targets including COX-2 and MMPs. The extracts also reversed the IL-1β-induced downregulation of collagen type II, CSPG, β1-integrin, and cartilage-specific transcription factor SOX-9 protein expression. In high-density cultures botanical extracts stimulated new cartilage formation even in the presence of IL-1β. Conclusions. Botanical extracts exerted anti-inflammatory and anabolic effects on chondrocytes. The observed reduction of IL-1β-induced NF-κB activation suggests that further studies are warranted to demonstrate the effectiveness of plant extracts in the treatment of OA and other conditions in which NF-κB plays pathophysiological roles.

SEXTANT X-Ray Pulsar Navigation Demonstration: Flight System and Test Results

Science.gov (United States)

Winternitz, Luke; Mitchell, Jason W.; Hassouneh, Munther A.; Valdez, Jennifer E.; Price, Samuel R.; Semper, Sean R.; Yu, Wayne H.; Ray, Paul S.; Wood, Kent S.; Arzoumanian, Zaven;

Integrated carbon analysis of biomass production on fallow agricultural land and product substitution in Sweden - Preliminary results

Energy Technology Data Exchange (ETDEWEB)

Dornburg, Veronika; Eggers, Thies; Gustavsson, Leif [Mid Sweden Univ., Oestersund (Sweden). Ecotechnology

2006-07-15

An important option in the Swedish context to reduce its net emissions of carbon dioxide (CO{sub 2}) is the increased use of biomass for energy and material substitution. On fallow agricultural land additional production of biomass would be possible. We analyse biomass production systems based on Norway spruce, hybrid poplar and willow hybrids and the use of this biomass to replace fossil energy and energy intensive material systems. The highest biomass production potential is for willow in southern Sweden. Fertilisation management of spruce could shorten the rotation lengths by about 17%. The fertilised production of Norway spruce with use of harvested timber for construction and use of remaining woody biomass for heat and power production gives the largest reductions of carbon emissions per hectare under the assumptions made. The use of willow for heat and power and of fertilised spruce for a wood product mix lead to the highest fossil primary energy savings in our scenarios. Spruce cultivations can achieve considerable carbon emission reductions in the long term, but willow and poplar might be a good option when fossil energy savings and carbon emission reductions should be achieved in the short term.

Louisville region demonstration of travel management coordination center : system pre-deployment preparation.

Science.gov (United States)

2013-03-01

The purpose of the Greater Louisville Region Demonstration of Travel Management Coordination Center (TMCC): System Pre-Deploy-ment Preparation grant was to further phased implementation of the regions TMCC design by focusing on two major component...

The demonstration test of urban EV rental system with 'Hypermini'

Energy Technology Data Exchange (ETDEWEB)

Teramoto, M.; Tohyama, E.; Kasai, J. [Nissan Motor Co. Ltd., Tochigi (Japan); Takayama, M. [Electric Technology for Automobile Traffic and Driving Association, Tokyo (Japan)

2000-07-01

The efforts taken by the Electric Technology for Automobile Traffic and Driving Association to address environmental pollution associated with traffic jams were discussed. An urban electric vehicle (EV) rent-a-car system has been proposed which combines the intelligent transportation system (ITS) and ultra small EVs as a fourth public traffic system after rail, bus and taxis. A demonstration test of this system began in October 1999 with the Suzuki Motor Corporation. A total of 30 small conversion EV and 20 ultra small EVs, called the 'Hypermini' were tested in the heavily populated Yokohama Minato Mirai 21 District (MM21). The impetus for the feasibility study was the lack of transportation from residential areas to stations and from stations to business areas. The objective was to provide a seamless traffic system for door-to-door service and to improve the use of vehicle parking spaces by an intelligent car sharing system. Another objective was to reduce the operating cost of company cars in urban areas. A comprehensive description of how the urban rent-a-car system works was included along with an overview of the system components and a description of vehicle stations. The solution to one-way-trips was solved by employing people to either drive or tow dropped-off vehicles to their original stations. So far, most users are satisfied with the service. Those with complaints, argued that the range was not sufficient. It was emphasized that in order for the system to be accepted nation wide, it is important to maintain low costs and high reliability in this demonstration stage.

Testing, development and demonstration of large scale solar district heating systems

DEFF Research Database (Denmark)

Furbo, Simon; Fan, Jianhua; Perers, Bengt

2015-01-01

In 2013-2014 the project “Testing, development and demonstration of large scale solar district heating systems” was carried out within the Sino-Danish Renewable Energy Development Programme, the so called RED programme jointly developed by the Chinese and Danish governments. In the project Danish...... know how on solar heating plants and solar heating test technology have been transferred from Denmark to China, large solar heating systems have been promoted in China, test capabilities on solar collectors and large scale solar heating systems have been improved in China and Danish-Chinese cooperation...

Design and Test Plans for a Non-Nuclear Fission Power System Technology Demonstration Unit

Science.gov (United States)

Mason, Lee; Palac, Donald; Gibson, Marc; Houts, Michael; Warren, John; Werner, James; Poston, David; Qualls, Arthur Lou; Radel, Ross; Harlow, Scott

2012-01-01

A joint National Aeronautics and Space Administration (NASA) and Department of Energy (DOE) team is developing concepts and technologies for affordable nuclear Fission Power Systems (FPSs) to support future exploration missions. A key deliverable is the Technology Demonstration Unit (TDU). The TDU will assemble the major elements of a notional FPS with a non-nuclear reactor simulator (Rx Sim) and demonstrate system-level performance in thermal vacuum. The Rx Sim includes an electrical resistance heat source and a liquid metal heat transport loop that simulates the reactor thermal interface and expected dynamic response. A power conversion unit (PCU) generates electric power utilizing the liquid metal heat source and rejects waste heat to a heat rejection system (HRS). The HRS includes a pumped water heat removal loop coupled to radiator panels suspended in the thermal-vacuum facility. The basic test plan is to subject the system to realistic operating conditions and gather data to evaluate performance sensitivity, control stability, and response characteristics. Upon completion of the testing, the technology is expected to satisfy the requirements for Technology Readiness Level 6 (System Demonstration in an Operational and Relevant Environment) based on the use of high-fidelity hardware and prototypic software tested under realistic conditions and correlated with analytical predictions.

Demonstration of micro-projection enabled short-range communication system for 5G.

Science.gov (United States)

Chou, Hsi-Hsir; Tsai, Cheng-Yu

2016-06-13

A liquid crystal on silicon (LCoS) based polarization modulated image (PMI) system architecture using red-, green- and blue-based light-emitting diodes (LEDs), which offers simultaneous micro-projection and high-speed data transmission at nearly a gigabit, serving as an alternative short-range communication (SRC) approach for personal communication device (PCD) application in 5G, is proposed and experimentally demonstrated. In order to make the proposed system architecture transparent to the future possible wireless data modulation format, baseband modulation schemes such as multilevel pulse amplitude modulation (M-PAM), M-ary phase shift keying modulation (M-PSK) and M-ary quadrature amplitude modulation (M-QAM) which can be further employed by more advanced multicarrier modulation schemes (such as DMT, OFDM and CAP) were used to investigate the highest possible data transmission rate of the proposed system architecture. The results demonstrated that an aggregative data transmission rate of 892 Mb/s and 900 Mb/s at a BER of 10^(-3) can be achieved by using 16-QAM baseband modulation scheme when data transmission were performed with and without micro-projection simultaneously.

Buried Waste Integrated Demonstration lessons learned: 1993 technology demonstrations

International Nuclear Information System (INIS)

Kostelnik, K.M.; Owens, K.J.

1994-01-01

An integrated technology demonstration was conducted by the Buried Waste Integrated Demonstration (BWID) at the Idaho National Engineering Laboratory Cold Test Pit in the summer of 1993. This program and demonstration was sponsored by the US Department of Energy Office of Technology Development. The demonstration included six technologies representing a synergistic system for the characterization and retrieval of a buried hazardous waste site. The integrated technology demonstration proved very successful and a summary of the technical accomplishments is presented. Upon completion of the integrated technology demonstration, cognizant program personnel participated in a lessons learned exercise. This exercise was conducted at the Simplot Decision Support Center at Idaho State University and lessons learned activity captured additional information relative to the integration of technologies for demonstration purposes. This information will be used by BWID to enhance program planning and strengthen future technology demonstrations

Demonstration of holographic smart card system using the optical memory technology

Science.gov (United States)

Kim, JungHoi; Choi, JaeKwang; An, JunWon; Kim, Nam; Lee, KwonYeon; Jeon, SeckHee

2003-05-01

In this paper, we demonstrate the holographic smart card system using digital holographic memory technique that uses reference beam encrypted by the random phase mask to prevent unauthorized users from accessing the stored digital page. The input data that include document data, a picture of face, and a fingerprint for identification is encoded digitally and then coupled with the reference beam modulated by a random phase mask. Therefore, this proposed system can execute recording in the order of MB~GB and readout all personal information from just one card without any additional database system. Also, recorded digital holograms can't be reconstructed without a phase key and can't be copied by using computers, scanners, or photography.

Demonstration of Multisetting One-Way Einstein-Podolsky-Rosen Steering in Two-Qubit Systems

Science.gov (United States)

Xiao, Ya; Ye, Xiang-Jun; Sun, Kai; Xu, Jin-Shi; Li, Chuan-Feng; Guo, Guang-Can

2017-04-01

Einstein-Podolsky-Rosen (EPR) steering describes the ability of one party to remotely affect another's state through local measurements. One of the most distinguishable properties of EPR steering is its asymmetric aspect. Steering can work in one direction but fail in the opposite direction. This type of one-way steering, which is different from the symmetry concepts of entanglement and Bell nonlocality, has garnered much interest. However, an experimental demonstration of genuine one-way EPR steering in the simplest scenario, i.e., one that employs two-qubit systems, is still lacking. In this Letter, we experimentally demonstrate one-way EPR steering with multimeasurement settings for a class of two-qubit states, which are still one-way steerable even with infinite settings. The steerability is quantified by the steering radius, which represents a necessary and sufficient steering criterion. The demonstrated one-way steering in the simplest bipartite quantum system is of fundamental interest and may provide potential applications in one-way quantum information tasks.

Experience with an ultrasonic sealing system for nuclear safeguards in irradiated fuel bay demonstrations

International Nuclear Information System (INIS)

White, B.F.; Smith, M.T.

1985-07-01

The development of the irradiated fuel safeguards containment assembly for CANDU nuclear generating stations has stimulated the development of the AECL Random Coil Sealing System. The ARC seal combines the identity and integrity elements in an ultrasonically-determined signature. This is verified in situ, in real time with the seal reading system. The maturation of this technology has been facilitated with demonstration trials in the NRU and NPD irradiated fuel bays. The NPD demonstration includes operation of the systems tooling by Ontario Hydro staff. It provides the opportunity for IAEA inspectors from Toronto and Vienna to direct the operational procedures and to perform the data acquisition. The procedures and systems developed in these trials are reviewed. The estimation of the system performance characteristics from the observations is presented. A minimum frequency of reading for individual seals is recommended to be once per annum following initial deployment

AZ-101 Mixer Pump Demonstration Data Acquisition System and Gamma Cart Data Acquisition Control System Software Configuration Management Plan

International Nuclear Information System (INIS)

WHITE, D.A.

1999-01-01

This Software Configuration Management Plan (SCMP) provides the instructions for change control of the AZ1101 Mixer Pump Demonstration Data Acquisition System (DAS) and the Sludge Mobilization Cart (Gamma Cart) Data Acquisition and Control System (DACS)

Groundwater Monitoring and Engineered Geothermal Systems: The Newberry EGS Demonstration

Science.gov (United States)

Grasso, K.; Cladouhos, T. T.; Garrison, G.

2013-12-01

Engineered Geothermal Systems (EGS) represent the next generation of geothermal energy development. Stimulation of multiple zones within a single geothermal reservoir could significantly reduce the cost of geothermal energy production. Newberry Volcano in central Oregon represents an ideal location for EGS research and development. As such, the goals of the Newberry EGS Demonstration, operated by AltaRock Energy, Inc., include stimulation of a multiple-zone EGS reservoir, testing of single-well tracers and a demonstration of EGS reservoir viability through flow-back and circulation tests. A shallow, local aquifer supplied the approximately 41,630 m3 (11 million gals) of water used during stimulation of NWG 55-29, a deep geothermal well on the western flank of Newberry Volcano. Protection of the local aquifer is of primary importance to both the Newberry EGS Demonstration and the public. As part of the Demonstration, AltaRock Energy, Inc. has developed and implemented a groundwater monitoring plan to characterize the geochemistry of the local aquifer before, during and after stimulation. Background geochemical conditions were established prior to stimulation of NWG 55-29, which was completed in 2012. Nine sites were chosen for groundwater monitoring. These include the water supply well used during stimulation of NWG 55-29, three monitoring wells, three domestic water wells and two hot seeps located in the Newberry Caldera. Together, these nine monitoring sites represent up-, down- and cross-gradient locations. Groundwater samples are analyzed for 25 chemical constituents, stable isotopes, and geothermal tracers used during stimulation. In addition, water level data is collected at three monitoring sites in order to better characterize the effects of stimulation on the shallow aquifer. To date, no significant geochemical changes and no geothermal tracers have been detected in groundwater samples from these monitoring sites. The Newberry EGS Demonstration groundwater

Experimental demonstration of subcarrier multiplexed quantum key distribution system.

Science.gov (United States)

Mora, José; Ruiz-Alba, Antonio; Amaya, Waldimar; Martínez, Alfonso; García-Muñoz, Víctor; Calvo, David; Capmany, José

2012-06-01

We provide, to our knowledge, the first experimental demonstration of the feasibility of sending several parallel keys by exploiting the technique of subcarrier multiplexing (SCM) widely employed in microwave photonics. This approach brings several advantages such as high spectral efficiency compatible with the actual secure key rates, the sharing of the optical fainted pulse by all the quantum multiplexed channels reducing the system complexity, and the possibility of upgrading with wavelength division multiplexing in a two-tier scheme, to increase the number of parallel keys. Two independent quantum SCM channels featuring a sifted key rate of 10 Kb/s/channel over a link with quantum bit error rate <2% is reported.

Fiscal 2000 report on data of international joint demonstrative development of photovoltaic power generation system. Demonstrative research on photovoltaic power generation system interconnection system (Myanmar); 2000 nendo taiyoko hatsuden system kokusai kyodo jissho kaihatsu hokokusho. Taiyoko hatsuden keito renkei system jissho kenkyu (Myanmar) - shiryohen

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

This paper describes the fiscal 2000 report on research data of joint demonstrative development with Myanmar concerning photovoltaic power generation system interconnection system. The purpose is an operation research in the case where a small-scale electric power generation system in an remote island or the like in Japan is linked with a severely output-fluctuating power generation system using energy of nature such as photovoltaic and wind power generation. In particular, among the system control (demand side management) methods by adjustment from a loading side, ballast load control was employed that adjustably operates load of an ice machine for example. As the contents of the data, the quantity of solar radiation and wind velocity at the Chaungthar site were shown as meteorological observation data. In addition, a graph was made on the meteorological observation data at the Chaungthar and Letkhokekone sites. The paper also explains the final explanatory data for selecting the sites in implementing the demonstrative research. As to the operation method of the hybrid power generation system, assumption was made for the daytime load in four cases from 50% (30kW) to 0% (0kW) of the nighttime. Storage batteries and diesel generators were installed and used in combination. Simulation results were also presented. (NEDO)

DEMONSTRATION OF A NO-VOC/NO-HAP WOOD KITCHEN CABINET COATING SYSTEM

Science.gov (United States)

The report gives results of the development and demonstration of a no-VOC (volatile organic compound)/no-HAP (hazardous air pollutant) wood furniture coating system at two cabinet manufacturing plants: one in Portland, OR, and the other in Redwood City, CA. Technology transfer ef...

Demonstration of Critical Systems for Propellant Production on Mars for Science and Exploration Missions

Science.gov (United States)

Linne, Diane L.; Gaier, James R.; Zoeckler, Joseph G.; Kolacz, John S.; Wegeng, Robert S.; Rassat, Scot D.; Clark, D. Larry

2013-01-01

A Mars hopper has been proposed as a Mars mobility concept that will also demonstrate and advance in-situ resource utilization. The components needed in a Mars propellant production plant have been developed to various levels of technology maturity, but there is little experience with the systems in a Mars environment. Two systems for the acquisition and compression of the thin carbon dioxide atmosphere were designed, assembled, and tested in a Mars environment chamber. A microchannel sorption pump system was able to raise the pressure from 7 Torr to 450 Torr or from 12 Torr to over 700 Torr in two stages. This data now provides information needed to make additional improvements in the sorption pump technology to increase performance, although a system-level analysis might prove that some amount of pre- or post-compression may be a preferred solution. A mini cryofreezer system was also evaluated as an alternative method for carbon dioxide acquisition and compression. Finally, an electrolysis system was tested and successfully demonstrated start-up operation and thermal stability of all components during long-term operation in the chamber.

The Ion Propulsion System for the Solar Electric Propulsion Technology Demonstration Mission

Science.gov (United States)

Herman, Daniel A.; Santiago, Walter; Kamhawi, Hani; Polk, James E.; Snyder, John Steven; Hofer, Richard R.; Parker, J. Morgan

2015-01-01

The Asteroid Redirect Robotic Mission is a candidate Solar Electric Propulsion Technology Demonstration Mission whose main objectives are to develop and demonstrate a high-power solar electric propulsion capability for the Agency and return an asteroidal mass for rendezvous and characterization in a companion human-crewed mission. The ion propulsion system must be capable of operating over an 8-year time period and processing up to 10,000 kg of xenon propellant. This high-power solar electric propulsion capability, or an extensible derivative of it, has been identified as a critical part of an affordable, beyond-low-Earth-orbit, manned-exploration architecture. Under the NASA Space Technology Mission Directorate the critical electric propulsion and solar array technologies are being developed. The ion propulsion system being co-developed by the NASA Glenn Research Center and the Jet Propulsion Laboratory for the Asteroid Redirect Vehicle is based on the NASA-developed 12.5 kW Hall Effect Rocket with Magnetic Shielding (HERMeS0 thruster and power processing technologies. This paper presents the conceptual design for the ion propulsion system, the status of the NASA in-house thruster and power processing activity, and an update on flight hardware.

A High-Resolution Terrestrial Modeling System (TMS): A Demonstration in China

Science.gov (United States)

Duan, Q.; Dai, Y.; Zheng, X.; Ye, A.; Ji, D.; Chen, Z.

2013-12-01

This presentation describes a terrestrial modeling system (TMS) developed at Beijing Normal University. The TMS is designed to be driven by multi-sensor meteorological and land surface observations, including those from satellites and land based observing stations. The purposes of the TMS are (1) to provide a land surface parameterization scheme fully capable of being coupled with the Earth system models; (2) to provide a standalone platform for retrospective historical simulation and for forecasting of future land surface processes at different space and time scales; and (3) to provide a platform for studying human-Earth system interactions and for understanding climate change impacts. This system is built on capabilities among several groups at BNU, including the Common Land Model (CoLM) system, high-resolution atmospheric forcing data sets, high resolution land surface characteristics data sets, data assimilation and uncertainty analysis platforms, ensemble prediction platform, and high-performance computing facilities. This presentation intends to describe the system design and demonstrate the capabilities of TMS with results from a China-wide application.

Experimental demonstration of improved fiber nonlinearity tolerance for unique-word DFT-spread OFDM systems.

Science.gov (United States)

Chen, Xi; Li, An; Gao, Guanjun; Shieh, William

2011-12-19

In this paper we experimentally demonstrate transmission performance of optical DFT-spread OFDM systems in comparison with conventional OFDM systems. A 440.8-Gb/s superchannel consisting of 8 x 55.1-Gb/s densely-spaced DFT-S OFDM signal is successfully received after 1120-km transmission with a spectral efficiency of 3.5 b/s/Hz. It is shown that DFT-S OFDM can achieve an improvement of 1 dB in Q factor and 1 dB in launch power over conventional OFDM. Additionally, unique word aided phase estimation algorithm is proposed and demonstrated enabling extremely long OFDM symbol transmission.

Energy market as a non-food application for European agriculture

International Nuclear Information System (INIS)

Sipilae, K.

1993-01-01

Sustainable non-food cropping systems for arable land are being studied intensively both in Scandinavia and elsewhere in Europe to find alternatives, in which the need for economic subvention would be lower than the export subsidies for grain or other food products. The area of arable land available for non-food cultivation is about 1 million hectares in Finland and 20 - 30 million hectares in the European Communities. In addition to conventional crops and afforestatation, it is possible to grow energy plants (willow, poplar, miscanthus, etc.) and agrofibre plants in these areas. Cultivation of energy willows or other corresponding plants of less than 5 m in height is usually not considered afforestation, as a willow field can easily be retaken into agricultural use with certain reservations (e.g., covered drains can be clogged) This article gives a survey of the alternatives for the utilization of non-food cropping systems

Design demonstrations for the remaining 19 Category B tank systems at Oak Ridge National Laboratory, Oak Ridge, Tennessee

International Nuclear Information System (INIS)

1993-06-01

This document presents design demonstrations conducted of liquid low-level waste (LLLW) storage tank systems located at the Oak Ridge National Laboratory (ORNL). ORNL has conducted research in energy related fields since 1943. The facilities used to conduct the research include nuclear reactors, chemical pilot plants, research laboratories, radioisotope production laboratories, and support facilities. These facilities have produced a variety of radioactive and/or hazardous wastes that have been transported and stored through an extensive network of piping and tankage. Demonstration of the design of these tank systems has been stipulated by the Federal Facility Agreement (FFA) between the EPA (United States Environmental Protection Agency)-Region IV; the Tennessee Department of Environment and Conservation (TDEC); and the DOE. The FFA establishes four categories of tank systems: Category A-New or Replacement Tank Systems with Secondary Containment; Category B-Existing Tank Systems with Secondary Containment; Category C-Existing Tank Systems Without Secondary Containment, and Category D-Existing Tank Systems Without Secondary Containment That are Removed from Service. This document provides a design demonstration of the secondary containment and ancillary equipment of 19 tank systems listed in the FFA as Category B. The design demonstration for each tank is presented in Section 2. The assessments assume that each tank system was constructed in accordance with the design drawings and construction specifications for that system unless specified otherwise. Each design demonstration addresses system conformance to the requirements of the FFA (Appendix F, Section C)

Hybrid Life Support System Technology Demonstrations

Science.gov (United States)

Morrow, R. C.; Wetzel, J. P.; Richter, R. C.

2018-02-01

Demonstration of plant-based hybrid life support technologies in deep space will validate the function of these technologies for long duration missions, such as Mars transit, while providing dietary variety to improve habitability.

Optical Verification Laboratory Demonstration System for High Security Identification Cards

Science.gov (United States)

Javidi, Bahram

1997-01-01

Document fraud including unauthorized duplication of identification cards and credit cards is a serious problem facing the government, banks, businesses, and consumers. In addition, counterfeit products such as computer chips, and compact discs, are arriving on our shores in great numbers. With the rapid advances in computers, CCD technology, image processing hardware and software, printers, scanners, and copiers, it is becoming increasingly easy to reproduce pictures, logos, symbols, paper currency, or patterns. These problems have stimulated an interest in research, development and publications in security technology. Some ID cards, credit cards and passports currently use holograms as a security measure to thwart copying. The holograms are inspected by the human eye. In theory, the hologram cannot be reproduced by an unauthorized person using commercially-available optical components; in practice, however, technology has advanced to the point where the holographic image can be acquired from a credit card-photographed or captured with by a CCD camera-and a new hologram synthesized using commercially-available optical components or hologram-producing equipment. Therefore, a pattern that can be read by a conventional light source and a CCD camera can be reproduced. An optical security and anti-copying device that provides significant security improvements over existing security technology was demonstrated. The system can be applied for security verification of credit cards, passports, and other IDs so that they cannot easily be reproduced. We have used a new scheme of complex phase/amplitude patterns that cannot be seen and cannot be copied by an intensity-sensitive detector such as a CCD camera. A random phase mask is bonded to a primary identification pattern which could also be phase encoded. The pattern could be a fingerprint, a picture of a face, or a signature. The proposed optical processing device is designed to identify both the random phase mask and the

Solar Powered Aircraft, Photovoltaic Array/Battery System Tabletop Demonstration: Design and Operation Manual

Science.gov (United States)

Colozza, Anthony J.; Scheiman, David A.; Bailey, Sheila (Technical Monitor)

2000-01-01

A system was constructed to demonstrate the power system operation of a solar powered aircraft. The system consists of a photovoltaic (PV) array, a charge controller, a battery, an electric motor and propeller. The system collects energy from the PV array and either utilizes this energy to operate an electric motor or stores it in a rechargeable battery for future use. The system has a control panel which displays the output of the array and battery as well as the total current going to the electric motor. The control panel also has a means for adjusting the output to the motor to control its speed. The entire system is regulated around 12 VDC.

Cross-terminology mapping challenges: A demonstration using medication terminological systems

Science.gov (United States)

Saitwal, Himali; Qing, David; Jones, Stephen; Bernstam, Elmer; Chute, Christopher G.; Johnson, Todd R.

2015-01-01

Standardized terminological systems for biomedical information have provided considerable benefits to biomedical applications and research. However, practical use of this information often requires mapping across terminological systems—a complex and time-consuming process. This paper demonstrates the complexity and challenges of mapping across terminological systems in the context of medication information. It provides a review of medication terminological systems and their linkages, then describes a case study in which we mapped proprietary medication codes from an electronic health record to SNOMED-CT and the UMLS Metathesaurus. The goal was to create a polyhierarchical classification system for querying an i2b2 clinical data warehouse. We found that three methods were required to accurately map the majority of actively prescribed medications. Only 62.5% of source medication codes could be mapped automatically. The remaining codes were mapped using a combination of semi-automated string comparison with expert selection, and a completely manual approach. Compound drugs were especially difficult to map: only 7.5% could be mapped using the automatic method. General challenges to mapping across terminological systems include (1) the availability of up-to-date information to assess the suitability of a given terminological system for a particular use case, and to assess the quality and completeness of cross-terminology links; (2) the difficulty of correctly using complex, rapidly evolving, modern terminologies; (3) the time and effort required to complete and evaluate the mapping; (4) the need to address differences in granularity between the source and target terminologies; and (5) the need to continuously update the mapping as terminological systems evolve. PMID:22750536

Habitat and sex differences in physiological condition of breeding Southwestern Willow Flycatchers (Empidonax traillii extimus)

Science.gov (United States)

Owen, J.C.; Sogge, M.K.; Kern, M.D.

2005-01-01

The Southwestern Willow Flycatcher (Empidonax traillii extimus; here- after “flycatcher”) is a federally listed endangered species that breeds in densely vegetated riparian habitats dominated by native and exotic plants, including introduced monotypic saltcedar (Tamarix ramosissima). Some workers have theorized that saltcedar is unsuitable habitat for the flycatcher, primarily because it generally supports a smaller and less diverse invertebrate community (the flycatcher's food base) than native habitats (e.g. Salix spp.). However, differences in insect communities between native and saltcedar habitats are not proof that saltcedar habitats are inferior. The only way to evaluate whether the habitats differ in dietary or energetic quality is to document actual food limitation or its manifestations. Measurements of an individual's body condition and metabolic state can serve as indicators of environmental stressors, such as food limitation and environmental extremes. We captured 130 flycatchers breeding in native and saltcedar habitats in Arizona and New Mexico and measured 12 variables of physiological condition. These variables included body mass, fat level, body condition index, hematocrit, plasma triglycerides, plasma free fatty acids and glycerol, plasma glucose and beta-hydroxybutyrate, plasma uric acid, total leukocyte count, and heterophil-to-lymphocyte ratio. We found substantial sex-based differences in the condition of male and female flycatchers. Ten of the 12 measures of physiological condition differed significantly between the sexes. In all cases where male and female condition differed (except mass), the differences suggest that males were in poorer condition than females. We found few habitat-based differences in flycatcher condition. Only 3 of the 12 physiological condition indices differed significantly between habitats. Our data show that, at least in some parts of the flycatcher's range, there is no evidence that flycatchers breeding in

Genetics of phenotypic plasticity and biomass traits in hybrid willows across contrasting environments and years.

Science.gov (United States)

Berlin, Sofia; Hallingbäck, Henrik R; Beyer, Friderike; Nordh, Nils-Erik; Weih, Martin; Rönnberg-Wästljung, Ann-Christin

2017-07-01

Phenotypic plasticity can affect the geographical distribution of taxa and greatly impact the productivity of crops across contrasting and variable environments. The main objectives of this study were to identify genotype-phenotype associations in key biomass and phenology traits and the strength of phenotypic plasticity of these traits in a short-rotation coppice willow population across multiple years and contrasting environments to facilitate marker-assisted selection for these traits. A hybrid Salix viminalis  × ( S. viminalis × Salix schwerinii ) population with 463 individuals was clonally propagated and planted in three common garden experiments comprising one climatic contrast between Sweden and Italy and one water availability contrast in Italy. Several key phenotypic traits were measured and phenotypic plasticity was estimated as the trait value difference between experiments. Quantitative trait locus (QTL) mapping analyses were conducted using a dense linkage map and phenotypic effects of S. schwerinii haplotypes derived from detected QTL were assessed. Across the climatic contrast, clone predictor correlations for biomass traits were low and few common biomass QTL were detected. This indicates that the genetic regulation of biomass traits was sensitive to environmental variation. Biomass QTL were, however, frequently shared across years and across the water availability contrast. Phenology QTL were generally shared between all experiments. Substantial phenotypic plasticity was found among the hybrid offspring, that to a large extent had a genetic origin. Individuals carrying influential S. schwerinii haplotypes generally performed well in Sweden but less well in Italy in terms of biomass production. The results indicate that specific genetic elements of S. schwerinii are more suited to Swedish conditions than to those of Italy. Therefore, selection should preferably be conducted separately for such environments in order to maximize biomass

Preliminary design of steam reformer in out-pile demonstration test facility for HTTR heat utilization system

Energy Technology Data Exchange (ETDEWEB)

Haga, Katsuhiro; Hino, Ryutaro; Inagaki, Yosiyuki; Hata, Kazuhiko; Aita, Hideki; Sekita, Kenji; Nishihara, Tetsuo; Sudo, Yukio [Japan Atomic Energy Research Inst., Oarai, Ibaraki (Japan). Oarai Research Establishment; Yamada, Seiya

1996-11-01

One of the key objectives of HTTR is to demonstrate effectiveness of high-temperature nuclear heat utilization system. Prior to connecting a heat utilization system to HTTR, an out-pile demonstration test is indispensable for the development of experimental apparatuses, operational control and safety technology, and verification of the analysis code of safety assessment. For the first heat utilization system of HTTR, design of the hydrogen production system by steam reforming is going on. We have proposed the out-pile demonstration test plan of the heat utilization system and conducted preliminary design of the test facility. In this report, design of the steam reformer, which is the principal component of the test facility, is described. In the course of the design, two types of reformers are considered. The one reformer contains three reactor tubes and the other contains one reactor tube to reduce the construction cost of the test facility. We have selected the steam reformer operational conditions and structural specifications by analyzing the steam reforming characteristics and component structural strength for each type of reformer. (author)

TRL Assessment of Solar Sail Technology Development Following the 20-Meter System Ground Demonstrator Hardware Testing

Science.gov (United States)

Young, Roy M.; Adams, Charles L.

2010-01-01

The NASA In-Space Propulsion Technology (ISPT) Projects Office sponsored two separate, independent solar sail system design and development demonstration activities during 2002-2005. ATK Space Systems of Goleta, CA was the prime contractor for one development team and L' Garde, Inc. of Tustin, CA was the prime contractor for the other development team. The goal of these activities was to advance the technology readiness level (TRL) of solar sail propulsion from 3 towards 6 by the year 2006. Component and subsystem fabrication and testing were completed successfully, including the ground deployment of 10-meter and 20-meter demonstration hardware systems under vacuum conditions. The deployment and structural testing of the 20-meter solar sail systems was conducted in the 30 meter diameter Space Power Facility thermal-vacuum chamber at NASA Glenn Plum Brook in April though August, 2005. This paper will present the results of the TRL assessment following the solar sail technology development activities associated with the design, development, analysis and testing of the 20-meter system ground demonstrators.

Demonstration of a Moving-Map System for Improved Lane Navigation of Amphibious Vehicles

National Research Council Canada - National Science Library

Clohrenz, Maura

2003-01-01

The Naval Research Laboratory (NRL) is testing and demonstrating a prototype moving-map system on amphibious vehicles and landing craft to aid the location neutralization and navigation around mines and obstacles in the surf and beach zone...

Design and simulation of a plant control system for a GCFR demonstration plant

International Nuclear Information System (INIS)

Estrine, E.A.; Greiner, H.G.

1980-02-01

A plant control system is being designed for a 300 MW(e) Gas Cooled Fast Breeder Reactor (GCFR) demonstration plant. Control analysis is being performed as an integral part of the plant design process to ensure that control requirements are satisfied as the plant design evolves. Plant models and simulations are being developed to generate information necessary to further define control system requirements for subsequent plant design iterations

Sprint: The first flight demonstration of the external work system robots

Science.gov (United States)

Price, Charles R.; Grimm, Keith

1995-01-01

The External Works Systems (EWS) 'X Program' is a new NASA initiative that will, in the next ten years, develop a new generation of space robots for active and participative support of zero g external operations. The robotic development will center on three areas: the assistant robot, the associate robot, and the surrogate robot that will support external vehicular activities (EVA) prior to and after, during, and instead of space-suited human external activities respectively. The EWS robotics program will be a combination of technology developments and flight demonstrations for operational proof of concept. The first EWS flight will be a flying camera called 'Sprint' that will seek to demonstrate operationally flexible, remote viewing capability for EVA operations, inspections, and contingencies for the space shuttle and space station. This paper describes the need for Sprint and its characteristics.

A comparative analysis of genetic differentiation across six shared willow host species in leaf- and bud-galling sawflies.

Directory of Open Access Journals (Sweden)

Sanna A Leppänen

Full Text Available Genetic divergence and speciation in plant-feeding insects could be driven by contrasting selection pressures imposed by different plant species and taxa. While numerous examples of host-associated differentiation (HAD have been found, the overall importance of HAD in insect diversification remains unclear, as few studies have investigated its frequency in relation to all speciation events. One promising way to infer the prevalence and repeatability of HAD is to estimate genetic differentiation in multiple insect taxa that use the same set of hosts. To this end, we measured and compared variation in mitochondrial COI and nuclear ITS2 sequences in population samples of leaf-galling Pontania and bud-galling Euura sawflies (Hymenoptera: Tenthredinidae collected from six Salix species in two replicate locations in northern Fennoscandia. We found evidence of frequent HAD in both species complexes, as individuals from the same willow species tended to cluster together on both mitochondrial and nuclear phylogenetic trees. Although few fixed differences among the putative species were found, hierarchical AMOVAs showed that most of the genetic variation in the samples was explained by host species rather than by sampling location. Nevertheless, the levels of HAD measured across specific pairs of host species were not correlated in the two focal galler groups. Hence, our results support the hypothesis of HAD as a central force in herbivore speciation, but also indicate that evolutionary trajectories are only weakly repeatable even in temporally overlapping radiations of related insect taxa.

Performance of a daylight redirecting glass shading system demonstration in an office building

DEFF Research Database (Denmark)

Appelfeld, David; Svendsen, Svend; Traberg-Borup, Steen

2011-01-01

This paper evaluates the daylighting performance of a prototype external dynamic integrated shading and light redirecting system. The demonstration project was carried out on a building with an open-plan office. The prototype and original façades were placed on the same floor with the same...... orientation and similar surroundings. The existing façade was used as the reference for measurements and simulations. The focus of this research project was to employ available simulation tools for the system performance evaluation. This was accompanied by measurements of the daylight conditions...... in the investigated space. The prototype system improved daylighting conditions compared to the existing shading system....

Integrated test plan ResonantSonic drilling system technology demonstration-1995, at the Hanford Site: Revision 1

International Nuclear Information System (INIS)

McLellan, G.W.

1994-01-01

This integrated test plan describes the demonstration test of the ResonantSonic drilling system. This demonstration is part of the Office of Technology Development's Volatile Organic Compound Arid Integrated Demonstration (VOC-Arid ID). Two main purposes of this demonstration are (1) to continue testing the ResonantSonic drilling system compatibility with the Hanford Site waste characterization programs, and (2) to transfer this method for use at the Hanford Site, other government sites, and the private sector. The ResonantSonic method is a dry drilling technique. Field testing of this method began in July 1993. During the next four months, nine holes were drilled, and continuous core samples were retrieved. Penetration rates were 2 to 3 times the baseline, and the operational downtime rate was less than 10%. Successfully demonstrated equipment refinements included a prototype 300 series ResonantSonic head, a new drill rod design for 18-centimeter diameter pipe, and an automated pipe handling system. Various configurations of sampling equipment and drill bits were tested, depending on geologic conditions. The principal objective of the VOC-Arid ID is to determine the viability of emerging technologies that can be used to characterize, remediate, and/or monitor arid or semiarid sites containing VOCs (e.g., carbon tetrachloride) with or without associated metal and radionuclide contamination

A Demonstration Setup to Simulate Detection of Planets outside the Solar System

Science.gov (United States)

Choopan, W.; Ketpichainarong, W.; Laosinchai, P.; Panijpan, B.

2011-01-01

We constructed a simple demonstration setup to simulate an extrasolar planet and its star revolving around the system's centre of mass. Periodic dimming of light from the star by the transiting planet and the star's orbital revolution simulate the two major ways of deducing the presence of an exoplanet near a distant star. Apart from being a…

Waste management system functional requirements for Interim Waste Management Facilities (IWMFs) and technology demonstrations, LLWDDD [Low-Level Disposal Development and Demonstration] Program

International Nuclear Information System (INIS)

1988-03-01

The purpose of this report is to build upon the preceding decisions and body of information to prepare draft system functional requirements for each classification of waste disposal currently proposed for Low-Level Waste Disposal Development Demonstration (LLWDDD) projects. Functional requirements identify specific information and data needs necessary to satisfy engineering design criteria/objectives for Interim Waste Management Facilities. This draft will suppor the alternatives evaluation process and will continue to evolve as strategy is implemented, regulatory limits are established, technical and economic uncertainties are resolved, and waste management plans are being implemented. This document will become the planning basis for the new generation of solid LLW management facilities on new sites on the Reservation. Eighteen (18) general system requirements are identified which are applicable to all four Low-Level Waste (LLW) disposal classifications. Each classification of LLW disposal is individually addressed with respect ot waste characteristics, site considerations, facility operations, facility closure/post-closure, intruder barriers, institutional control, and performance monitoring requirements. Three initial LLW disposal sites have been proposed as locations on the ORR for the first demonstrations

Design of helium-gas supplying facility of out-of-pile demonstration test for HTTR heat utilization system

Energy Technology Data Exchange (ETDEWEB)

Hino, Ryutaro; Fujisaki, Katsuo; Kobayashi, Toshiaki [Japan Atomic Energy Research Inst., Oarai, Ibaraki (Japan). Oarai Research Establishment] [and others

1996-09-01

One of the objectives of the High-Temperature Engineering Test Reactor (HTTR) is to demonstrate effectiveness of high-temperature heat utilization. Prior to connect a heat utilization system to the HTTR, a series of out-of-pile demonstration test is indispensable to improve components` performance, to demonstrate operation, control and safety technologies and to verify analysis codes for design and safety evaluation. After critical review and discussion on the out-of-pile demonstration test, a test facility have been designed. In this report, a helium-gas supplying facility simulated the HTTR system was described in detail, which supplies High-temperature helium-gas of 900degC to a steam reforming facility mocking-up the HTTR heat utilization system. Components of the Helium Engineering Demonstration Loop (HENDEL) were selected to reuse in the helium-gas supplying facility in order to decrease construction cost. Structures and specifications of new components such as a high-temperature heater and a preheater were decided after evaluation of thermal and hydraulic performance and strength. (author)

Combined production of free-range pigs and energy crops – animal behaviour and crop damages

DEFF Research Database (Denmark)

Horsted, Klaus; Kongsted, Anne Grete; Jørgensen, Uffe

2012-01-01

Intensive free-range pig production on open grasslands has disadvantages in that it creates nutrient hotspots and little opportunity for pigs to seek shelter from the sun. Combining a perennial energy crop and pig production might benefit the environment and animal welfare because perennial energy...... crops like willow (Salix sp.) and Miscanthus offer the pigs protection from the sun while reducing nutrient leaching from pig excrements due to their deep rooting system. The objectives of this study were to evaluate how season and stocking density of pigs in a free-range system with zones of willow...

RF System for the MICE Demonstration of Ionisation Cooling

Energy Technology Data Exchange (ETDEWEB)

Ronald, K.; et al.

2017-04-01

Muon accelerators offer an attractive option for a range of future particle physics experiments. They can enable high energy (TeV+) high energy lepton colliders whilst mitigating the difficulty of synchrotron losses, and can provide intense beams of neutrinos for fundamental physics experiments investigating the physics of flavor. The method of production of muon beams results in high beam emittance which must be reduced for efficient acceleration. Conventional emittance control schemes take too long, given the very short (2.2 microsecond) rest lifetime of the muon. Ionisation cooling offers a much faster approach to reducing particle emittance, and the international MICE collaboration aims to demonstrate this technique for the first time. This paper will present the MICE RF system and its role in the context of the overall experiment.

The Potential Use of Agroforestry Community Gardens as a Sustainable Import-Substitution Strategy for Enhancing Food Security in Subarctic Ontario, Canada

Directory of Open Access Journals (Sweden)

Maren Oelbermann

2013-09-01

Full Text Available The high prevalence of food insecurity experienced by northern First Nations partially results from dependence on an expensive import-based food system that typically lacks nutritional quality and further displaces traditional food systems. In the present study, the feasibility of import substitution by Agroforestry Community Gardens (AFCGs as socio-ecologically and culturally sustainable means of enhancing food security was explored through a case study of Fort Albany First Nation in subarctic Ontario, Canada. Agroforestry is a diverse tree-crop agricultural system that has enhanced food security in the tropics and subtropics. Study sites were selected for long-term agroforestry research to compare Salix spp. (willow-dominated AFCG plots to a “no tree” control plot in Fort Albany. Initial soil and vegetative analysis revealed a high capacity for all sites to support mixed produce with noted modifications, as well as potential competitive and beneficial willow-crop interactions. It is anticipated that inclusion of willow trees will enhance the long-term productive capacity of the AFCG test plots. As an adaptable and dynamic system, AFCGs have potential to act as a more reliable local agrarian system and a refuge for culturally significant plants in high-latitude First Nation socio-ecological systems, which are particularly vulnerable to rapid cultural, climatic, and ecological change.

Distributed picture compilation demonstration

Science.gov (United States)

Alexander, Richard; Anderson, John; Leal, Jeff; Mullin, David; Nicholson, David; Watson, Graham

2004-08-01

A physical demonstration of distributed surveillance and tracking is described. The demonstration environment is an outdoor car park overlooked by a system of four rooftop cameras. The cameras extract moving objects from the scene, and these objects are tracked in a decentralized way, over a real communication network, using the information form of the standard Kalman filter. Each node therefore has timely access to the complete global picture and because there is no single point of failure in the system, it is robust. The demonstration system and its main components are described here, with an emphasis on some of the lessons we have learned as a result of applying a corpus of distributed data fusion theory and algorithms in practice. Initial results are presented and future plans to scale up the network are also outlined.

Laboratory information system data demonstrate successful ...

African Journals Online (AJOL)

The National Health Laboratory Service (NHLS) performs the PCR tests for the public health sector and stores test data in a corporate data warehouse (CDW). Objectives. To demonstrate the utility of laboratory data for monitoring trends in EID coverage and early vertical transmission rates and to describe the scale-up of the ...

Report on demonstrative research on photovoltaic power generation system in Myanmar

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

With an objective of installation and demonstrative operation in Myanmar of a power generation system combining a small-scale photovoltaic power generation system, a wind power generation system, and a diesel generator, research and development is being made under a six year plan starting in 1999 and ending in 2004. Comparative discussions were given on the installation location of the power generation system for the climatic conditions in Chaungthar and Letkhokekone, whereas the final decision was given on Chaungthar. This project plans installation of a photovoltaic power generation system of 80 kW, a wind power generation system of 40 kW, and a diesel generator of 60 kW. Power generation will start at 6 o'clock in the morning and continue to 11 o'clock at night every day, with a storage battery of 1,000 Ah and a stabilized load comprising of ice maker units to be installed. Observation of wind power and solar insolation is being continued with an aim of acquiring data over a period of one year or longer, whereas the data as have been forecasted are being acquired at the present. The diesel generator was manufactured in Japan, which has been arrived at the port of Yangon in February 2001, and installed at the site in Chaungthar in March. (NEDO)

Reviews of the In-situ Demonstration Test of the Engineered Barrier System in Many Countries

Energy Technology Data Exchange (ETDEWEB)

Lee, Minsoo; Choi, Heui Joo [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2013-10-15

Many nations considering the deep geologic disposal of HLW are now planning or executing in-situ demonstration experiments on their regional EBS (Engineering barrier system) at their deep underground research facilities. The main purpose of the in-situ EBS test is the experimental confirmation of its performance, and the prediction of its long-term evolution through the modeling of EBS based on the experimental data. Additionally, the engineering feasibility for the construction of an engineering barrier system can also be checked through full scale construction of an in-situ test. KAERI is currently preparing an in-situ test at a large 1/3 scale, called IN-DEBS (In-situ Demonstration of EBS) at KURT (KAERI Underground Research Tunnel) for the generic EBS suggested in A-KRS (Advanced KAERI Reference System), which was developed to treat the HLW from pyroprocessing. As the first step for the design of IN-DEBS, the foreign in-situ demonstrations of EBS were reviewed in this paper. The demonstration projects, which were completed or are still being executed in some countries such as Sweden, France, Finland, Canada, Belgium, Switzerland, Spain, and Japan, were surveyed and summarized. In particular, hardware constitutions such as the heating element or compact bentonite, and the experimental procedures, have focused more on reviews than on experimental results in this survey, since their hardware information is very important for the design of the IN-DEBS.

Reviews of the In-situ Demonstration Test of the Engineered Barrier System in Many Countries

International Nuclear Information System (INIS)

Lee, Minsoo; Choi, Heui Joo

2013-01-01

Many nations considering the deep geologic disposal of HLW are now planning or executing in-situ demonstration experiments on their regional EBS (Engineering barrier system) at their deep underground research facilities. The main purpose of the in-situ EBS test is the experimental confirmation of its performance, and the prediction of its long-term evolution through the modeling of EBS based on the experimental data. Additionally, the engineering feasibility for the construction of an engineering barrier system can also be checked through full scale construction of an in-situ test. KAERI is currently preparing an in-situ test at a large 1/3 scale, called IN-DEBS (In-situ Demonstration of EBS) at KURT (KAERI Underground Research Tunnel) for the generic EBS suggested in A-KRS (Advanced KAERI Reference System), which was developed to treat the HLW from pyroprocessing. As the first step for the design of IN-DEBS, the foreign in-situ demonstrations of EBS were reviewed in this paper. The demonstration projects, which were completed or are still being executed in some countries such as Sweden, France, Finland, Canada, Belgium, Switzerland, Spain, and Japan, were surveyed and summarized. In particular, hardware constitutions such as the heating element or compact bentonite, and the experimental procedures, have focused more on reviews than on experimental results in this survey, since their hardware information is very important for the design of the IN-DEBS

Experimental demonstration of polar coded IM/DD optical OFDM for short reach system

Science.gov (United States)

Fang, Jiafei; Xiao, Shilin; Liu, Ling; Bi, Meihua; Zhang, Lu; Zhang, Yunhao; Hu, Weisheng

2017-11-01

In this paper, we propose a novel polar coded intensity modulation direct detection (IM/DD) optical orthogonal frequency division multiplexing (OFDM) system for short reach system. A method of evaluating the channel signal noise ratio (SNR) is proposed for soft-demodulation. The experimental results demonstrate that, compared to the conventional case, ∼9.5 dB net coding gain (NCG) at the bit error rate (BER) of 1E-3 can be achieved after 40-km standard single mode fiber (SSMF) transmission. Based on the experimental result, (512,256) polar code with low complexity and satisfactory BER performance meets the requirement of low latency in short reach system, which is a promising candidate for latency-stringent short reach optical system.

Large-scale demonstration test plan for digface data acquisition system

International Nuclear Information System (INIS)

Roybal, L.G.; Svoboda, J.M.

1994-11-01

Digface characterization promotes the use of online site characterization and monitoring during waste retrieval efforts, a need that arises from safety and efficiency considerations during the cleanup of a complex waste site. Information concerning conditions at the active digface can be used by operators as a basis for adjusting retrieval activities to reduce safety risks and to promote an efficient transition between retrieval and downstream operations. Most importantly, workers are given advance warning of upcoming dangerous conditions. In addition, detailed knowledge of digface conditions provides a basis for selecting tools and methods that avoid contamination spread and work stoppages. In FY-94, work began in support of a largescale demonstration coordinating the various facets of a prototype digface remediation operation including characterization, contaminant suppression, and cold waste retrieval. This test plan describes the activities that will be performed during the winter of FY-95 that are necessary to assess the performance of the data acquisition and display system in its initial integration with hardware developed in the Cooperative Telerobotic Retrieval (CTR) program. The six specific objectives of the test are determining system electrical noise, establishing a dynamic background signature of the gantry crane and associated equipment, determining the resolution of the overall system by scanning over known objects, reporting the general functionality of the overall data acquisition system, evaluating the laser topographic functionality, and monitoring the temperature control features of the electronic package

Irvine Smart Grid Demonstration, a Regional Smart Grid Demonstration Project

Energy Technology Data Exchange (ETDEWEB)

Yinger, Robert [Southern California Edison Company, Rosemead, CA (United States); Irwin, Mark [Southern California Edison Company, Rosemead, CA (United States)

2015-12-29

ISGD was a comprehensive demonstration that spanned the electricity delivery system and extended into customer homes. The project used phasor measurement technology to enable substation-level situational awareness, and demonstrated SCE’s next-generation substation automation system. It extended beyond the substation to evaluate the latest generation of distribution automation technologies, including looped 12-kV distribution circuit topology using URCIs. The project team used DVVC capabilities to demonstrate CVR. In customer homes, the project evaluated HAN devices such as smart appliances, programmable communicating thermostats, and home energy management components. The homes were also equipped with energy storage, solar PV systems, and a number of energy efficiency measures (EEMs). The team used one block of homes to evaluate strategies and technologies for achieving ZNE. A home achieves ZNE when it produces at least as much renewable energy as the amount of energy it consumes annually. The project also assessed the impact of device-specific demand response (DR), as well as load management capabilities involving energy storage devices and plug-in electric vehicle charging equipment. In addition, the ISGD project sought to better understand the impact of ZNE homes on the electric grid. ISGD’s SENet enabled end-to-end interoperability between multiple vendors’ systems and devices, while also providing a level of cybersecurity that is essential to smart grid development and adoption across the nation. The ISGD project includes a series of sub-projects grouped into four logical technology domains: Smart Energy Customer Solutions, Next-Generation Distribution System, Interoperability and Cybersecurity, and Workforce of the Future. Section 2.3 provides a more detailed overview of these domains.

Experimental Demonstration of Coexistence of Microwave Wireless Communication and Power Transfer Technologies for Battery-Free Sensor Network Systems

Directory of Open Access Journals (Sweden)

Satoshi Yoshida

2013-01-01

Full Text Available This paper describes experimental demonstrations of a wireless power transfer system equipped with a microwave band communication function. Battery charging using the system is described to evaluate the possibility of the coexistence of both wireless power transfer and communication functions in the C-band. A battery-free wireless sensor network system is demonstrated, and a high-power rectifier for the system is also designed and evaluated in the S-band. We have confirmed that microwave wireless power transfer can coexist with communication function.

The integrated melter off-gas treatment systems at the West Valley Demonstration Project

Energy Technology Data Exchange (ETDEWEB)

Vance, R.F. [West Valley Nuclear Services Co., Inc., NY (United States)

1995-02-01

The West Valley Demonstration Project was established by Public Law 96-368, the {open_quotes}West Valley Demonstration Project Act, {close_quotes} on October 1, l980. Under this act, Congress directed the Department of Energy to carry out a high level radioactive waste management demonstration project at the Western New York Nuclear Service Center in West Valley, New York. The purpose of this project is to demonstrate solidification techniques which can be used for preparing high level radioactive waste for disposal. In addition to developing this technology, the West Valley Demonstration Project Act directs the Department of Energy to: (1) develop containers suitable for permanent disposal of the high level waste; (2) transport the solidified high level waste to a Federal repository; (3) dispose of low level and transuranic waste produced under the project; and (4) decontaminate and decommission the facilities and materials associated with project activities and the storage tanks originally used to store the liquid high level radioactive waste. The process of vitrification will be used to solidify the high level radioactive liquid wastes into borosilicate glass. This report describes the functions, the controlling design criteria, and the resulting design of the melter off-gas treatment systems which are used in the vitrification process.

SEAMIST trademark in-situ instrumentation and vapor sampling system applications in the Sandia Mixed Waste Landfill Integrated Demonstration Program

International Nuclear Information System (INIS)

Lowry, W.E.; Dunn, S.D.; Cremer, S.C.; Williams, C.

1994-01-01

The SEAMIST trademark inverting membrane deployment system has been used successfully at the Mixed Waste Landfill Integrated Demonstration (MWLID) for multipoint vapor sampling/pressure measurement/permeability measurement/sensor integration demonstrations and borehole lining. Several instruments were deployed inside the SEAMIST trademark lined boreholes to detect metals, radionuclides, moisture, and geologic variations. The liner protected the instruments from contamination, maintained support of the uncased borehole wall, and sealed the total borehole from air circulation. The current activities have included the installation of three multipoint vapor sampling systems and sensor integration systems in 100-foot-deep vertical boreholes. A long term pressure monitoring program has recorded barometric pressure effects at depth with relatively high spatial resolution. The SEAMIST trademark system has been integrated with a variety of hydrologic and chemical sensors for in-situ measurements, demonstrating its versatility as an instrument deployment system which allows easy emplacement and removal. Standard SEAMIST trademark vapor sampling systems were also integrated with state-of-the-art VOC analysis technologies (automated GC, UV laser fluorometer). The results and status of these demonstration tests are presented

Demonstration testing and evaluation of in situ soil heating. Revision 1, Demonstration system design

International Nuclear Information System (INIS)

Dev, H.

1994-01-01

Over the last nine years IIT Research Institute (IITRI) has been developing and testing the in situ heating and soil decontamination process for the remediation of soils containing hazardous organic contaminants. In this process the soil is heated in situ using electrical energy. The contaminants are removed from the soil due to enhanced vaporization, steam distillation and stripping. The vaporized contaminants, water vapor and air are recovered from the heated zone by means of a vacuum manifold system which collects gases from below surface as well as from the soil surface. A vapor barrier is used to prevent fugitive emissions of the contaminants and to control air infiltration to minimize dilution of the contaminant gases and vapors. The recovered gases and vapors are conveyed to an on site vapor treatment system for the clean up of the vent gases. Electrical energy is applied to the soil by forming an array of electrodes in the soil which are electrically interconnected and supplied with power. The electrodes are placed in drilled bore holes which are made through the contaminated zone. There are two versions of the in situ heating and soil treatment process: the f irst version is called the In Situ Radio Frequency (RF) Soil Decontamination Process and the second version is called the In Situ Electromagnetic (EM) Soil Decontamination Process. The first version, the RF Process is capable of heating the soil in a temperature range of 100 degrees to 400 degrees C. The soil temperature in the second version, the EM Process, is limited to the boiling point of water under native conditions. Thus the soil will be heated to a temperature of about 85 degrees to 95 degrees C. In this project IITRI will demonstrate the EM Process for in situ soil decontamination at K-25 Site due to the fact that most of the contaminants of concern are volatile organics which can be removed by heating the soil to a temperature range of 85 degrees to 95 degrees C

Demonstration testing and evaluation of in situ soil heating. Revision 1, Demonstration system design

Energy Technology Data Exchange (ETDEWEB)

Dev, H.

1994-08-16

Over the last nine years IIT Research Institute (IITRI) has been developing and testing the in situ heating and soil decontamination process for the remediation of soils containing hazardous organic contaminants. In this process the soil is heated in situ using electrical energy. The contaminants are removed from the soil due to enhanced vaporization, steam distillation and stripping. The vaporized contaminants, water vapor and air are recovered from the heated zone by means of a vacuum manifold system which collects gases from below surface as well as from the soil surface. A vapor barrier is used to prevent fugitive emissions of the contaminants and to control air infiltration to minimize dilution of the contaminant gases and vapors. The recovered gases and vapors are conveyed to an on site vapor treatment system for the clean up of the vent gases. Electrical energy is applied to the soil by forming an array of electrodes in the soil which are electrically interconnected and supplied with power. The electrodes are placed in drilled bore holes which are made through the contaminated zone. There are two versions of the in situ heating and soil treatment process: the f irst version is called the In Situ Radio Frequency (RF) Soil Decontamination Process and the second version is called the In Situ Electromagnetic (EM) Soil Decontamination Process. The first version, the RF Process is capable of heating the soil in a temperature range of 100{degrees} to 400{degrees}C. The soil temperature in the second version, the EM Process, is limited to the boiling point of water under native conditions. Thus the soil will be heated to a temperature of about 85{degrees} to 95{degrees}C. In this project IITRI will demonstrate the EM Process for in situ soil decontamination at K-25 Site due to the fact that most of the contaminants of concern are volatile organics which can be removed by heating the soil to a temperature range of 85{degrees} to 95{degrees}C.

Application of multimedia image technology in engineering report demonstration system

Science.gov (United States)

Lili, Jiang

2018-03-01

With the rapid development of global economic integration, people’s strong desire for a wide range of global exchanges and interactions has been promoted, and there are more unprecedented convenient means for people to know the world and even to transform the world. At this stage, we realize that the traditional mode of work has become difficult to adapt to the changing trends of the world and informatization, multimedia, science and technology have become the mainstream of the times. Therefore, this paper will mainly analyze the present situation of the project report demonstration system and the key points of the work and put forward with pertinence specific application strategy of the integration with multimedia image technology.

Modeling of Solid State Transformer for the FREEDM System Demonstration

Science.gov (United States)

Jiang, Youyuan

The Solid State Transformer (SST) is an essential component in the FREEDM system. This research focuses on the modeling of the SST and the controller hardware in the loop (CHIL) implementation of the SST for the support of the FREEDM system demonstration. The energy based control strategy for a three-stage SST is analyzed and applied. A simplified average model of the three-stage SST that is suitable for simulation in real time digital simulator (RTDS) has been developed in this study. The model is also useful for general time-domain power system analysis and simulation. The proposed simplified av-erage model has been validated in MATLAB and PLECS. The accuracy of the model has been verified through comparison with the cycle-by-cycle average (CCA) model and de-tailed switching model. These models are also implemented in PSCAD, and a special strategy to implement the phase shift modulation has been proposed to enable the switching model simulation in PSCAD. The implementation of the CHIL test environment of the SST in RTDS is described in this report. The parameter setup of the model has been discussed in detail. One of the dif-ficulties is the choice of the damping factor, which is revealed in this paper. Also the grounding of the system has large impact on the RTDS simulation. Another problem is that the performance of the system is highly dependent on the switch parameters such as voltage and current ratings. Finally, the functionalities of the SST have been realized on the platform. The distributed energy storage interface power injection and reverse power flow have been validated. Some limitations are noticed and discussed through the simulation on RTDS.

Demonstration and evaluation of the pulsed ultraviolet-irradiation gas-treatment system, Savannah River Site

International Nuclear Information System (INIS)

Schneider, J.; Wilkey, M.; Peters, R.; Tomczyk, N.; Friedlund, J.; Farber, P.

1994-10-01

Argonne National Laboratory was asked to demonstrate and evaluate a pulsed ultraviolet-irradiation system developed by Purus, Inc., at the Volatile Organic Compounds Non-Arid Integrated Demonstration at the Savannah River Site near aiken, South Carolina. The Purus system consists of four reactor chambers, each containing a xenon flash lamp. During the two weeks of testing, samples were taken and analyzed from the inlet and outlet sides of the Purus system. The contaminants of concern on the inlet were tetrachloroethylene (PCE), trichloroethylene (TCE), and 1,1,1-trichloroethane (TCA); the contaminants of concern on the outlet were PCE, TCE, TCA, carbon tetrachloride (CT), and chloroform. The evaluation of the Purus system included an examination of the reduction of both TCE and PCE and a search for any change in the concentrations. (Operating conditions included flow rates, ranging from 25 to 100 standard cubic feet per minute; inlet concentration of PCE, ranging from 360 to 10,700 parts per million volume; and flash lamp rates, ranging from 1 to 30 hertz.) The Purus system was quite efficient at reducing the concentrations of both PCE and TCE. The potential by-products, TCA, CT, and chloroform, showed no significant increases throughout the range of the various operating parameters. Overall, the Purus system appears to be a cost-efficient means of reducing the concentrations of PCE and TCE, while the removal of the initial photo-oxidation products and TCA is slower and needs further evaluation

Distribution and abundance of Least Bell’s Vireos (Vireo bellii pusillus) and Southwestern Willow Flycatchers (Empidonax traillii extimus) on the Middle San Luis Rey River, San Diego, southern California—2016 data summary

Science.gov (United States)

Allen, Lisa D.; Howell, Scarlett L.; Kus, Barbara E.

2017-09-29

Executive SummaryWe surveyed for Least Bell’s Vireos (LBVI) (Vireo bellii pusillus) and Southwestern Willow Flycatchers (SWFL) (Empidonax traillii extimus) along the San Luis Rey River, between College Boulevard in Oceanside and Interstate 15 in Fallbrook, California (middle San Luis Rey River), in 2016. Surveys were done from March 30 to July 11 (LBVI) and from May 18 to July 30 (SWFL). We found 142 LBVI territories, at least 106 of which were occupied by pairs. Six additional transient LBVIs were detected. Of 20 banded LBVIs detected in the survey area, 9 had been given full color-band combinations prior to 2016, although we were unable to determine the exact color combination of 1 female LBVI. Seven other LBVIs with single (natal) federal bands were recaptured and banded in 2016. Four vireos with single dark blue federal bands indicating that they were banded as nestlings on the lower San Luis Rey River could not be recaptured for identification.Three SFWL territories were observed in the survey area in 2016. Two territories were occupied by pairs and one by a male of unknown breeding status. Both pairs attempted to nest at least once, and both pairs were successful, fledging three young each. Nesting began in early June and continued into July. Brown-Headed Cowbird (Molothrus ater) eggs were not observed in either nest. An additional 12 transient Willow Flycatchers of unknown subspecies were detected in 2016.Two of the five resident SWFLs were originally banded as nestlings on Marine Corps Base Camp Pendleton. One male and one female were banded as nestlings on Camp Pendleton in 2009 and 2011, respectively. One natal male of unknown breeding status, originally banded as a nestling on the middle San Luis Rey River in 2015, was recaptured and given a unique color combination in 2016. This male was later detected on Marine Corps Base Camp Pendleton.

Phytoremediation of a petroleum-hydrocarbon contaminated shallow aquifer in Elizabeth City, North Carolina, USA

Science.gov (United States)

Nichols, Elizabeth Guthrie; Cook, Rachel L.; Landmeyer, James E.; Atkinson, Brad; Malone, Donald R.; Shaw, George; Woods, Leilani

2014-01-01

A former bulk fuel terminal in North Carolina is a groundwater phytoremediation demonstration site where 3,250 hybrid poplars, willows, and pine trees were planted from 2006 to 2008 over approximately 579,000 L of residual gasoline, diesel, and jet fuel. Since 2011, the groundwater altitude is lower in the area with trees than outside the planted area. Soil-gas analyses showed a 95 percent mass loss for total petroleum hydrocarbons (TPH) and a 99 percent mass loss for benzene, toluene, ethylbenzene, and xylenes (BTEX). BTEX and methyl tert-butyl ether concentrations have decreased in groundwater. Interpolations of free-phase, fuel product gauging data show reduced thicknesses across the site and pooling of fuel product where poplar biomass is greatest. Isolated clusters of tree mortalities have persisted in areas with high TPH and BTEX mass. Toxicity assays showed impaired water use for willows and poplars exposed to the site's fuel product, but Populus survival was higher than the willows or pines on-site, even in a noncontaminated control area. All four Populus clones survived well at the site.

Demonstration of a switchable damping system to allow low-noise operation of high-Q low-mass suspension systems

Science.gov (United States)

Hennig, Jan-Simon; Barr, Bryan W.; Bell, Angus S.; Cunningham, William; Danilishin, Stefan L.; Dupej, Peter; Gräf, Christian; Hough, James; Huttner, Sabina H.; Jones, Russell; Leavey, Sean S.; Pascucci, Daniela; Sinclair, Martin; Sorazu, Borja; Spencer, Andrew; Steinlechner, Sebastian; Strain, Kenneth A.; Wright, Jennifer; Zhang, Teng; Hild, Stefan

2017-12-01

Low-mass suspension systems with high-Q pendulum stages are used to enable quantum radiation pressure noise limited experiments. Utilizing multiple pendulum stages with vertical blade springs and materials with high-quality factors provides attenuation of seismic and thermal noise; however, damping of these high-Q pendulum systems in multiple degrees of freedom is essential for practical implementation. Viscous damping such as eddy-current damping can be employed, but it introduces displacement noise from force noise due to thermal fluctuations in the damping system. In this paper we demonstrate a passive damping system with adjustable damping strength as a solution for this problem that can be used for low-mass suspension systems without adding additional displacement noise in science mode. We show a reduction of the damping factor by a factor of 8 on a test suspension and provide a general optimization for this system.

Budgetary and Programmatic Fluctuations during the System Development and Demonstration Phase: A Case Study of the Marine Corps H-1 Upgrade Program

Science.gov (United States)

2007-12-01

impact of economic change might include a closing factory, market manipulation, the signing of international trade 17 treaties, or the global...Refinement System Intergration System Demonstration Concept Decision BA C LRIP Full-Rate Production & Deployment System Development and Demonstration...BLOCK III Concept Exploration Component Advanced Development Concept and Technology Development System Intergration System Demonstration Decision Review

Photovoltaic Power System and Power Distribution Demonstration for the Desert RATS Program

Science.gov (United States)

Colozza, Anthony; Jakupca, Ian; Mintz, Toby; Herlacher, Mike; Hussey, Sam

2012-01-01

A stand alone, mobile photovoltaic power system along with a cable deployment system was designed and constructed to take part in the Desert Research And Technology Studies (RATS) lunar surface human interaction evaluation program at Cinder Lake, Arizona. The power system consisted of a photovoltaic array/battery system. It is capable of providing 1 kW of electrical power. The system outputs were 48 V DC, 110 V AC, and 220 V AC. A cable reel with 200 m of power cable was used to provide power from the trailer to a remote location. The cable reel was installed on a small trailer. The reel was powered to provide low to no tension deployment of the cable. The cable was connected to the 220 V AC output of the power system trailer. The power was then converted back to 110 V AC on the cable deployment trailer for use at the remote site. The Scout lunar rover demonstration vehicle was used to tow the cable trailer and deploy the power cable. This deployment was performed under a number of operational scenarios, manned operation, remote operation and tele-robotically. Once deployed, the cable was used to provide power, from the power system trailer, to run various operational tasks at the remote location.

Results of a Demonstration Assessment of Passive System Reliability Utilizing the Reliability Method for Passive Systems (RMPS)

Energy Technology Data Exchange (ETDEWEB)

Bucknor, Matthew; Grabaskas, David; Brunett, Acacia; Grelle, Austin

2015-04-26

Advanced small modular reactor designs include many advantageous design features such as passively driven safety systems that are arguably more reliable and cost effective relative to conventional active systems. Despite their attractiveness, a reliability assessment of passive systems can be difficult using conventional reliability methods due to the nature of passive systems. Simple deviations in boundary conditions can induce functional failures in a passive system, and intermediate or unexpected operating modes can also occur. As part of an ongoing project, Argonne National Laboratory is investigating various methodologies to address passive system reliability. The Reliability Method for Passive Systems (RMPS), a systematic approach for examining reliability, is one technique chosen for this analysis. This methodology is combined with the Risk-Informed Safety Margin Characterization (RISMC) approach to assess the reliability of a passive system and the impact of its associated uncertainties. For this demonstration problem, an integrated plant model of an advanced small modular pool-type sodium fast reactor with a passive reactor cavity cooling system is subjected to a station blackout using RELAP5-3D. This paper discusses important aspects of the reliability assessment, including deployment of the methodology, the uncertainty identification and quantification process, and identification of key risk metrics.

Research, Development and Demonstration of Micro-CHP System for Residential Applications

Energy Technology Data Exchange (ETDEWEB)

Karl Mayer

2010-03-31

ECR International and its joint venture company, Climate Energy, are at the forefront of the effort to deliver residential-scale combined heat and power (Micro-CHP) products to the USA market. Part of this substantial program is focused on the development of a new class of steam expanders that offers the potential for significantly lower costs for small-scale power generation technology. The heart of this technology is the scroll expander, a machine that has revolutionized the HVAC refrigerant compressor industry in the last 15 years. The liquid injected cogeneration (LIC) technology is at the core of the efforts described in this report, and remains an excellent option for low cost Micro-CHP systems. ECR has demonstrated in several prototype appliances that the concept for LIC can be made into a practical product. The continuing challenge is to identify economical scroll machine designs that will meet the performance and endurance requirements needed for a long life appliance application. This report describes the numerous advances made in this endeavor by ECR International. Several important advances are described in this report. Section 4 describes a marketing and economics study that integrates the technical performance of the LIC system with real-world climatic data and economic analysis to assess the practical impact that different factors have on the economic application of Micro-CHP in residential applications. Advances in the development of a working scroll steam expander are discussed in Section 5. A rigorous analytical assessment of the performance of scroll expanders, including the difficult to characterize impact of pocket to pocket flank leakage, is presented in Section 5.1. This is followed with an FEA study of the thermal and pressure induced deflections that would result from the normal operation of an advanced scroll expander. Section 6 describes the different scroll expanders and test fixtures developed during this effort. Another key technical

A habitat overlap analysis derived from maxent for tamarisk and the south-western willow flycatcher

Science.gov (United States)

York, Patricia; Evangelista, Paul; Kumar, Sunil; Graham, James; Flather, Curtis; Stohlgren, Thomas

2011-06-01

Biologic control of the introduced and invasive, woody plant tamarisk ( Tamarix spp, saltcedar) in south-western states is controversial because it affects habitat of the federally endangered South-western Willow Flycatcher ( Empidonax traillii extimus). These songbirds sometimes nest in tamarisk where floodplain-level invasion replaces native habitats. Biologic control, with the saltcedar leaf beetle ( Diorhabda elongate), began along the Virgin River, Utah, in 2006, enhancing the need for comprehensive understanding of the tamarisk-flycatcher relationship. We used maximum entropy (Maxent) modeling to separately quantify the current extent of dense tamarisk habitat (>50% cover) and the potential extent of habitat available for E. traillii extimus within the studied watersheds. We used transformations of 2008 Landsat Thematic Mapper images and a digital elevation model as environmental input variables. Maxent models performed well for the flycatcher and tamarisk with Area Under the ROC Curve (AUC) values of 0.960 and 0.982, respectively. Classification of thresholds and comparison of the two Maxent outputs indicated moderate spatial overlap between predicted suitable habitat for E. traillii extimus and predicted locations with dense tamarisk stands, where flycatcher habitat will potentially change flycatcher habitats. Dense tamarisk habitat comprised 500 km2 within the study area, of which 11.4% was also modeled as potential habitat for E. traillii extimus. Potential habitat modeled for the flycatcher constituted 190 km2, of which 30.7% also contained dense tamarisk habitat. Results showed that both native vegetation and dense tamarisk habitats exist in the study area and that most tamarisk infestations do not contain characteristics that satisfy the habitat requirements of E. traillii extimus. Based on this study, effective biologic control of Tamarix spp. may, in the short term, reduce suitable habitat available to E. traillii extimus, but also has the potential

Can nutrient status of four woody plant species be predicted using field spectrometry?

NARCIS (Netherlands)

Ferwerda, J.G.; Skidmore, A.K.

2007-01-01

This paper demonstrates the potential of hyperspectral remote sensing to predict the chemical composition (i.e., nitrogen, phosphorous, calcium, potassium, sodium, and magnesium) of three tree species (i.e., willow, mopane and olive) and one shrub species (i.e., heather). Reflectance spectra,

Solar renovation demonstration projects

Energy Technology Data Exchange (ETDEWEB)

Bruun Joergensen, O [ed.

1998-10-01

In the framework of the IEA SHC Programme, a Task on building renovation was initiated, `Task 20, Solar Energy in Building Renovation`. In a part of the task, Subtask C `Design of Solar Renovation Projects`, different solar renovation demonstration projects were developed. The objective of Subtask C was to demonstrate the application of advanced solar renovation concepts on real buildings. This report documents 16 different solar renovation demonstration projects including the design processes of the projects. The projects include the renovation of houses, schools, laboratories, and factories. Several solar techniques were used: building integrated solar collectors, glazed balconies, ventilated solar walls, transparent insulation, second skin facades, daylight elements and photovoltaic systems. These techniques are used in several simple as well as more complex system designs. (au)

E/Z MAS demonstration

International Nuclear Information System (INIS)

Boor, M.G.; Hurford, J.M.; Landry, R.P.; Martinez, B.J.; Solem, A.M.; Whiteson, R.; Zardecki, A.

1998-01-01

Los Alamos National Laboratory has developed E/Z MAS, a new generation nuclear material accountability application based on the latest technology and designed for facilities required to track nuclear materials with a simple-to-use interface. E/Z MAS is based on years of experience spent developing nuclear material accounting systems. E/Z MAS uses a modern relational database with a web server and enables users on a classified local area network to interact with the database with web browsers. The E/Z MAS Demonstration poster session demonstrates the E/Z MAS functions required by an operational nuclear facility to track material as it enters and leaves a facility and to account for the material as it moves through a process. The generation of internal facility reports and external reports for the Russian Federal system will be demonstrated. Bar-code readers will be used to demonstrate the ability of EZ MAS to automate certain functions, such as physical inventories at facilities

Yield Mapping in Salix; Skoerdekartering av salix

Energy Technology Data Exchange (ETDEWEB)

Anderson, Christoffer; Gilbertsson, Mikael; Rogstrand, Gustav; Thylen, Lars

2004-09-01

The most common species for energy forest production is willow. Willow is able to produce a large amount of biomass in a short period of time. Growing willow has a potential to render a good financial result for the farmer if cultivated on fields with the right conditions and plenty of water. Under the right conditions growing willow can give the farmer a net income of 3,000 SEK (about 430 USD) per hectare and year, which is something that common cereal crops cannot compete with. However, this is not the common case since willow is often grown as a substitute crop on fields where cereal crop yield is low. The aim of this study was to reveal if it is possible to measure yield variability in willow, and if it is possible to describe the reasons for yield variation both within the field but also between different fields. Yield mapping has been used in conventional farming for about a decade. The principles for yield mapping are to continuously measure the yield while registering location by the use of GPS when harvesting the field. The collected data is then used to search for spatial variations within the field, and to try to understand the reasons for this variation. Since there is currently no commercial equipment for yield mapping in willow, a yield mapping system had to be developed within this project. The new system was installed on a Claas Jaguar harvester. The principle for yield mapping on the Claas Jaguar harvester is to measure the distance between the feeding rollers. This distance is correlated to the flow through the harvester. The speed and position of the machine was registered using GPS. Knowing the working width of the harvester this information was used to calculate the yield. All collected data was stored on a PDA computer. Soil samples were also collected from the yield mapped fields. This was to be able to test yield against both physical and chemical soil parameters. The result shows that it is possible to measure spatial variations of yield in

Demonstrating EnTracked a System for Energy-Efficient Position Tracking for Mobile Devices

DEFF Research Database (Denmark)

Kjærgaard, Mikkel Baun; Jensen, Jakob Langdal; Godsk, Torben

An important feature of a modern mobile device is that it can position itself. Not only for use on the device but also for remote applications that require tracking of the device. To be useful, such position tracking has to be energy-efficient to avoid having a major impact on the battery life...... of the mobile device. To address this challenge we have build a system named EnTracked that, based on the estimation and prediction of system conditions and mobility, schedules position updates to both minimize energy consumption and optimize robustness. In this demonstration we would like to show how...

Engineered Geothermal System Demonstration Project

Energy Technology Data Exchange (ETDEWEB)

Petty, Susan

2014-06-19

In June 2009, AltaRock Energy began field work on a project supported by the U.S. Department of Energy entitled “Use of Multiple Stimulations to Improve Economics of Engineered Geothermal Systems in Shallow High Temperature Intrusives.” The goal of the project was to develop an Engineered Geothermal System (EGS) in the portion of The Geysers geothermal field operated by the Northern California Power Agency (NCPA). The project encountered several problems while deepening Well E-7 which culminated in the suspension of field activities in September 2009. Some of the problems encountered are particular to The Geysers area, while others might be encountered in any geothermal field, and they might be avoided in future operations.

Remote monitoring demonstration

International Nuclear Information System (INIS)

Caskey, Susan; Olsen, John

2006-01-01

The recently upgraded remote monitoring system at the Joyo Experimental Reactor uses a DCM-14 camera module and GEMINI software. The final data is compatible both with the IAEA-approved GARS review software and the ALIS software that was used for this demonstration. Features of the remote monitoring upgrade emphasized compatibility with IAEA practice. This presentation gives particular attention to the selection process for meeting network security considerations at the O'arai site. The Joyo system is different from the NNCA's ACPF system, in that it emphasizes use of IAEA standard camera technology and data acquisition and transmission software. In the demonstration itself, a temporary virtual private network (VPN) between the meeting room and the server at Sandia in Albuquerque allowed attendees to observe data stored from routine transmissions from the Joyo Fresh Fuel Storage to Sandia. Image files from a fuel movement earlier in the month showed Joyo workers and IAEA inspectors carrying out a transfer. (author)

Demonstration of measuring sea fog with an SNSPD-based Lidar system.

Science.gov (United States)

Zhu, Jiang; Chen, Yajun; Zhang, Labao; Jia, Xiaoqing; Feng, Zhijun; Wu, Ganhua; Yan, Xiachao; Zhai, Jiquan; Wu, Yang; Chen, Qi; Zhou, Xiaoying; Wang, Zhizhong; Zhang, Chi; Kang, Lin; Chen, Jian; Wu, Peiheng

2017-11-08

The monitor of sea fogs become more important with the rapid development of marine activities. Remote sensing through laser is an effective tool for monitoring sea fogs, but still challengeable for large distance. We demonstrated a Long-distance Lidar for sea fog with superconducting nanowire single-photon detector (SNSPD), which extended the ranging area to a 180-km diameter area. The system, which was verified by using a benchmark distance measurement of a known island, is applied to the Mie scattering weather prediction Lidar system. The fog echo signal distribution in the range of 42.3∼63.5 km and 53.2∼74.2 km was obtained by the Lidar system. Then the fog concentration and the velocity of the fog were deduced from the distribution, which is consistent with the weather prediction. The height of the sea fog is about two hundred meter while the visibility at this height is about 90 km due to the Earth's radius of curvature. Therefore, the capability of this SNSPD-based Lidar was close to the theoretical limit for sea fog measurements for extremely high signal-to-noise ratio of SNSPD.

Demonstration of reliability centered maintenance

International Nuclear Information System (INIS)

Schwan, C.A.; Morgan, T.A.

1991-04-01

Reliability centered maintenance (RCM) is an approach to preventive maintenance planning and evaluation that has been used successfully by other industries, most notably the airlines and military. Now EPRI is demonstrating RCM in the commercial nuclear power industry. Just completed are large-scale, two-year demonstrations at Rochester Gas ampersand Electric (Ginna Nuclear Power Station) and Southern California Edison (San Onofre Nuclear Generating Station). Both demonstrations were begun in the spring of 1988. At each plant, RCM was performed on 12 to 21 major systems. Both demonstrations determined that RCM is an appropriate means to optimize a PM program and improve nuclear plant preventive maintenance on a large scale. Such favorable results had been suggested by three earlier EPRI pilot studies at Florida Power ampersand Light, Duke Power, and Southern California Edison. EPRI selected the Ginna and San Onofre sites because, together, they represent a broad range of utility and plant size, plant organization, plant age, and histories of availability and reliability. Significant steps in each demonstration included: selecting and prioritizing plant systems for RCM evaluation; performing the RCM evaluation steps on selected systems; evaluating the RCM recommendations by a multi-disciplinary task force; implementing the RCM recommendations; establishing a system to track and verify the RCM benefits; and establishing procedures to update the RCM bases and recommendations with time (a living program). 7 refs., 1 tab

Nitrate removal in a restored riparian groundwater system: functioning and importance of individual riparian zones

Directory of Open Access Journals (Sweden)

S. Peter

2012-11-01

Full Text Available For the design and the assessment of river restoration projects, it is important to know to what extent the elimination of reactive nitrogen (N can be improved in the riparian groundwater. We investigated the effectiveness of different riparian zones, characterized by a riparian vegetation succession, for nitrate (NO₃⁻ removal from infiltrating river water in a restored and a still channelized section of the river Thur, Switzerland. Functional genes of denitrification (nirS and nosZ were relatively abundant in groundwater from willow bush and mixed forest dominated zones, where oxygen concentrations remained low compared to the main channel and other riparian zones. After flood events, a substantial decline in NO₃⁻ concentration (> 50% was observed in the willow bush zone but not in the other riparian zones closer to the river. In addition, the characteristic enrichment of ¹⁵N and ¹⁸O in the residual NO₃⁻ pool (by up to 22‰ for δ¹⁵N and up to 12‰ for δ¹⁸O provides qualitative evidence that the willow bush and forest zones were sites of active denitrification and, to a lesser extent, NO₃⁻ removal by plant uptake. Particularly in the willow bush zone during a period of water table elevation after a flooding event, substantial input of organic carbon into the groundwater occurred, thereby fostering post-flood denitrification activity that reduced NO₃⁻ concentration with a rate of ~21 μmol N l⁻¹ d⁻¹. Nitrogen removal in the forest zone was not sensitive to flood pulses, and overall NO₃⁻ removal rates were lower (~6 μmol l⁻¹ d⁻¹. Hence, discharge-modulated vegetation–soil–groundwater coupling was found to be a key driver for riparian NO₃⁻ removal. We estimated that

High-Lift Propeller System Configuration Selection for NASA's SCEPTOR Distributed Electric Propulsion Flight Demonstrator

Science.gov (United States)

Patterson, Michael D.; Derlaga, Joseph M.; Borer, Nicholas K.

2016-01-01

Although the primary function of propellers is typically to produce thrust, aircraft equipped with distributed electric propulsion (DEP) may utilize propellers whose main purpose is to act as a form of high-lift device. These \\high-lift propellers" can be placed upstream of wing such that, when the higher-velocity ow in the propellers' slipstreams interacts with the wing, the lift is increased. This technique is a main design feature of a new NASA advanced design project called Scalable Convergent Electric Propulsion Technology Operations Research (SCEPTOR). The goal of the SCEPTOR project is design, build, and y a DEP aircraft to demonstrate that such an aircraft can be much more ecient than conventional designs. This paper provides details into the high-lift propeller system con guration selection for the SCEPTOR ight demonstrator. The methods used in the high-lift propeller system conceptual design and the tradeo s considered in selecting the number of propellers are discussed.

Coordinating Mobile Databases: A System Demonstration

OpenAIRE

Zaihrayeu, Ilya; Giunchiglia, Fausto

2004-01-01

In this paper we present the Peer Database Management System (PDBMS). This system runs on top of the standard database management system, and it allows it to connect its database with other (peer) databases on the network. A particularity of our solution is that PDBMS allows for conventional database technology to be effectively operational in mobile settings. We think of database mobility as a database network, where databases appear and disappear spontaneously and their network access point...

Experimental demonstration of 2.5 Gbit/S incoherent two-dimensional optical code division multiple access system

International Nuclear Information System (INIS)

Glesk, I.; Baby, V.; Bres, C.-S.; Xu, L.; Rand, D.; Prucnal, P.R.

2004-01-01

We demonstrated error-free operation of 4 simultaneous users in a fast frequency-hopping time-spreading optical code division multiple access system operating at 2.5 Gbit/s a Star architecture. Effective power penalty was ≤0.5dB. Novel optical code division multiple access receiver based on Terahertz Optical Asymmetric Demultiplexer was demonstrated to eliminate multiple access interference (Authors)

Habitat Demonstration Unit (HDU) Pressurized Excursion Module (PEM) Systems Integration Strategy

Science.gov (United States)

Gill, Tracy; Merbitz, Jerad; Kennedy, Kriss; Tri, Terry; Toups, Larry; Howe, A. Scott

2011-01-01

The Habitat Demonstration Unit (HDU) project team constructed an analog prototype lunar surface laboratory called the Pressurized Excursion Module (PEM). The prototype unit subsystems were integrated in a short amount of time, utilizing a rapid prototyping approach that brought together over 20 habitation-related technologies from a variety of NASA centers. This paper describes the system integration strategies and lessons learned, that allowed the PEM to be brought from paper design to working field prototype using a multi-center team. The system integration process was based on a rapid prototyping approach. Tailored design review and test and integration processes facilitated that approach. The use of collaboration tools including electronic tools as well as documentation enabled a geographically distributed team take a paper concept to an operational prototype in approximately one year. One of the major tools used in the integration strategy was a coordinated effort to accurately model all the subsystems using computer aided design (CAD), so conflicts were identified before physical components came together. A deliberate effort was made following the deployment of the HDU PEM for field operations to collect lessons learned to facilitate process improvement and inform the design of future flight or analog versions of habitat systems. Significant items within those lessons learned were limitations with the CAD integration approach and the impact of shell design on flexibility of placing systems within the HDU shell.

A COMPREHENSIVE TECHNICAL REVIEW OF THE DEMONSTRATION BULK VITRIFICATION SYSTEM

International Nuclear Information System (INIS)

SCHAUS, P.S.

2006-01-01

In May 2006, CH2M Hill Hanford Group, Inc. chartered an Expert Review Panel (ERP) to review the current status of the Demonstration Bulk Vitrification System (DBVS). It is the consensus of the ERP that bulk vitrification is a technology that requires further development and evaluation to determine its potential for meeting the Hanford waste stabilization mission. No fatal flaws (issues that would jeopardize the overall DBVS mission that cannot be mitigated) were found, given the current state of the project. However, a number of technical issues were found that could significantly affect the project's ability to meet its overall mission as stated in the project ''Justification of Mission Need'' document, if not satisfactorily resolved. The ERP recognizes that the project has changed from an accelerated schedule demonstration project to a formally chartered project that must be in full compliance with DOE 413.3 requirements. The perspective of the ERP presented herein, is measured against the formally chartered project as stated in the approved Justification of Mission Need document. A justification of Mission Need document was approved in July 2006 which defined the objectives for the DBVS Project. In this document, DOE concluded that bulk vitrification is a viable technology that requires additional development to determine its potential applicability to treatment of a portion of the Hanford low activity waste. The DBVS mission need statement now includes the following primary objectives: (1) process approximately 190,000 gallons of Tank S-109 waste into fifty 100 metric ton boxes of vitrified product; (2) store and dispose of these boxes at Hanford's Integrated Disposal Facility (IDF); (3) evaluate the waste form characteristics; (4) gather pilot plant operability data, and (5) develop the overall life cycle system performance of bulk vitrification and produce a comparison of the bulk vitrification process to building a second LAW Immobilization facility or other

The Blend Down Monitoring System Demonstration at the Padijcah Gaseous Diffusion Plant

International Nuclear Information System (INIS)

Benton, J.; Close, D.; Johnson, W. Jr.; Kerr, P.; March-Leuba, J.; Mastal, E.; Moss, C.; Powell, D.; Sumner, J.; Uckan, T.; Vines, R.; Wright, P.D.

1999-01-01

Agreements between the governments of the US and the Russian Federation for the US purchase of low enriched uranium (LEU) derived from highly enriched uranium (HEU) from dismantled Russian nuclear weapons calls for the establishment of transparency measures to provide confidence that nuclear nonproliferation goals are being met. To meet these transparency goals, the agreements call for the installation of nonintrusive US instruments to monitor the down blending of HEU to LEU. The Blend Down Monitoring System (BDMS) has been jointly developed by the Los Alamos National Laboratory (LANL) and the Oak Ridge National Laboratory (ORNL) to continuously monitor 235 U enrichments and mass flow rates at Russian blending facilities. Prior to its installation in Russian facilities, the BDMS was installed and operated in a UF 6 flow loop in the Paducah Gaseous Diffusion Plant simulating flow and enrichment conditions expected in a typical down-blending facility. A Russian delegation to the US witnessed the equipment demonstration in June, 1998. To conduct the demonstration in the Paducah Gaseous Diffusion Plant (PGDP), the BDMS was required to meet stringent Nuclear Regulatory Commission licensing, safety and operational requirements. The Paducah demonstration was an important milestone in achieving the operational certification for the BDMS use in Russian facilities

Preliminary Failure Modes, Effects and Criticality Analysis (FMECA) of the Brayton Isotope Power System (BIPS) Ground Demonstration System. Report 76-311965

International Nuclear Information System (INIS)

Miller, L.G.

1976-01-01

A Failure Modes, Effects and Criticality Analysis (FMECA) has been made of the Brayton Isotope Power System Ground Demonstration System (BIPS-GDS). Details of the analysis are discussed. The BIPS Flight System was recently analyzed in an AIRPHX report. Since the results of the Flight System FMECA are directly applicable to the BIPS to be tested in the GDS mode, the contents of the earlier FMECA have not been repeated in this current analysis. The BIPS-FS FMECA has been reviewed and determined to be essentially current

Implementation of a Sage-Based Stirling Model Into a System-Level Numerical Model of the Fission Power System Technology Demonstration Unit

Science.gov (United States)

Briggs, Maxwell H.

2011-01-01

The Fission Power System (FPS) project is developing a Technology Demonstration Unit (TDU) to verify the performance and functionality of a subscale version of the FPS reference concept in a relevant environment, and to verify component and system models. As hardware is developed for the TDU, component and system models must be refined to include the details of specific component designs. This paper describes the development of a Sage-based pseudo-steady-state Stirling convertor model and its implementation into a system-level model of the TDU.

IXV re-entry demonstrator: Mission overview, system challenges and flight reward

Science.gov (United States)

Angelini, Roberto; Denaro, Angelo

2016-07-01

The Intermediate eXperimental Vehicle (IXV) is an advanced re-entry demonstrator vehicle aimed to perform in-flight experimentation of atmospheric re-entry enabling systems and technologies. The IXV integrates key technologies at the system level, with significant advancements on Europe's previous flying test-beds. The project builds on previous achievements at system and technology levels, and provides a unique and concrete way of establishing and consolidating Europe's autonomous position in the strategic field of atmospheric re-entry. The IXV mission and system objectives are the design, development, manufacturing, assembling and on-ground to in-flight verification of an autonomous European lifting and aerodynamically controlled reentry system, integrating critical re-entry technologies at system level. Among such critical technologies of interest, special attention is paid to aerodynamic and aerothermodynamics experimentation, including advanced instrumentation for aerothermodynamics phenomena investigations, thermal protections and hot-structures, guidance, navigation and flight control through combined jets and aerodynamic surfaces (i.e. flaps), in particular focusing on the technologies integration at system level for flight. Following the extensive detailed design, manufacturing, qualification, integration and testing of the flight segment and ground segment elements, IXV has performed a full successful flight on February 11th 2015. After the launch with the VEGA launcher form the CSG spaceport in French Guyana, IXV has performed a full nominal mission ending with a successful splashdown in the Pacific Ocean. During Flight Phase, the IXV space and ground segments worked perfectly, implementing the whole flight program in line with the commanded maneuvers and trajectory prediction, performing an overall flight of 34.400 km including 7.600 km with hot atmospheric re-entry in automatic guidance, concluding with successful precision landing at a distance of ~1

The integrated melter off-gas treatment systems at the West Valley Demonstration Project

International Nuclear Information System (INIS)

Vance, R.F.

1991-12-01

The West Valley Demonstration project was established by an act of Congress in 1980 to solidify the high level radioactive liquid wastes produced from operation of the Western New York Nuclear Services Center from 1966 to 1972. The waste will be solidified as borosilicate glass. This report describes the functions, the controlling design criteria, and the resulting design of the melter off-gas treatment systems

Numerical analysis of the in-well vapor-stripping system demonstration at Edwards Air Force Base

International Nuclear Information System (INIS)

White, M.D.; Gilmore, T.J.

1996-10-01

Numerical simulations, with the Subsurface Transport Over Multiple Phases (STOMP) simulator, were applied to the field demonstration of an in-well vapor-stripping system at Edwards Air Force Base (AFB), near Mojave, California. The demonstration field site on the Edwards AFB was previously contaminated from traversing groundwater that was contained a varied composition of volatile organic compounds (VOCs), which primarily includes trichloroethylene (TCE). Contaminant TCE originated from surface basin that had been used to collect runoff during the cleaning of experimental rocket powered planes in the 1960s and 1970s. This report documents those simulations and associated numerical analyses. A companion report documents the in- well vapor-stripping demonstration from a field perspective

Buried Waste Integrated Demonstration

International Nuclear Information System (INIS)

1994-03-01

The Buried Waste Integrated Demonstration (BWID) supports the applied research, development, demonstration, and evaluation of a suite of advanced technologies that offer promising solutions to the problems associated with the remediation of buried waste. BWID addresses the difficult remediation problems associated with DOE complex-wide buried waste, particularly transuranic (TRU) contaminated buried waste. BWID has implemented a systems approach to the development and demonstration of technologies that will characterize, retrieve, treat, and dispose of DOE buried wastes. This approach encompasses the entire remediation process from characterization to post-monitoring. The development and demonstration of the technology is predicated on how a technology fits into the total remediation process. To address all of these technological issues, BWID has enlisted scientific expertise of individuals and groups from within the DOE Complex, as well as experts from universities and private industry. The BWID mission is to support development and demonstration of a suite of technologies that, when integrated with commercially-available technologies, forms a comprehensive, remediation system for the effective and efficient remediation of buried waste throughout the DOE Complex. BWID will evaluate and validate demonstrated technologies and transfer this information and equipment to private industry to support the Office of Environmental Restoration (ER), Office of Waste Management (WM), and Office of Facility Transition (FT) remediation planning and implementation activities

Use of Willows in Evapotranspirative Systems for Onsite Wastewater Management – Theory and Experiences from Denmark

DEFF Research Database (Denmark)

Brix, Hans; Arias, Carlos Alberto

2011-01-01

Evapotranspiration (ET) is a method of onsite wastewater treatment and disposal that is an alternative to conventional soil absorption systems, particularly for sites where protecting surface water and ground water is essential or where soil infiltration is not possible. One of the most important...... aspects of ET systems is their ability to evapotranspire all of the sewage discharged into the systems and the rain falling onto the systems. On an annual basis the ET should equal the amount of wastewater discharged into the system plus the amount of precipitation falling onto the system. Part......, their design, construction and management as well as operational experience are described....

Innovative technology demonstrations

International Nuclear Information System (INIS)

Anderson, D.B.; Hartley, J.N.; Luttrell, S.P.

1992-04-01

Currently, several innovative technologies are being demonstrated at Tinker Air Force Base (TAFB) to address specific problems associated with remediating two contaminated test sites at the base. Cone penetrometer testing (CPT) is a form of testing that can rapidly characterize a site. This technology was selected to evaluate its applicability in the tight clay soils and consolidated sandstone sediments found at TAFB. Directionally drilled horizontal wells have been successfully installed at the US Department of Energy's (DOE) Savannah River Site to test new methods of in situ remediation of soils and ground water. This emerging technology was selected as a method that may be effective in accessing contamination beneath Building 3001 without disrupting the mission of the building, and in enhancing the extraction of contamination both in ground water and in soil. A soil gas extraction (SGE) demonstration, also known as soil vapor extraction, will evaluate the effectiveness of SGE in remediating fuels and TCE contamination contained in the tight clay soil formations surrounding the abandoned underground fuel storage vault located at the SW Tanks Site. In situ sensors have recently received much acclaim as a technology that can be effective in remediating hazardous waste sites. Sensors can be useful for determining real-time, in situ contaminant concentrations during the remediation process for performance monitoring and in providing feedback for controlling the remediation process. A demonstration of two in situ sensor systems capable of providing real-time data on contamination levels will be conducted and evaluated concurrently with the SGE demonstration activities. Following the SGE demonstration, the SGE system and SW Tanks test site will be modified to demonstrate bioremediation as an effective means of degrading the remaining contaminants in situ

Simulated evapotranspiration from a landfill irrigated with landfill leachate

International Nuclear Information System (INIS)

Aronsson, P.

1996-01-01

Evapotranspiration from a landfill area, irrigated with leachate water, was simulated with the SOIL model. Three different types of vegetation (bare soil, grass ley, and willow) were used both with and without irrigation. The highest simulated evapotranspiration (604 mm) during the growing season was found from an irrigated willow stand with a high interception capacity. The lowest evapotranspiration (164 mm) was found from the bare soil. The relatively high evapotranspiration from the willow was probably caused by the high LAI (Leaf Area Index) and the low aerodynamic resistance within the willow stand. The results indicate that it is possible to reduce most of the leakage water from a landfill by irrigation of willow stands. 9 refs, 4 figs, 1 tab

Report on demonstrative research on photovoltaic power generation system in Myanmar. Appendices

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

With an objective of installation and demonstrative operation in Myanmar of a power generation system combining a small-scale photovoltaic power generation system, a wind power generation system, and a diesel generator, research and development is being made under a six year plan starting in 1999 and ending in 2004. This paper compiles the appendices related thereto. Collected for the climatic observation are the insolation data and wind velocity data in Chaungthar, and the insolation graph in both of Chaungthar and Lethokekone. Furthermore, materials for selection and decision on the installation location, and design materials for a hybrid power generation system were collected. Collected for procurement, construction, and installation of devices and facilities include test data for the diesel generator, drawings for the power generation control panel, test operation report, bill of lading for the diesel generator, a completion certificate of the diesel generator building, photographs of the building, a certificate of completion of installation of the diesel generator, photographs taken during the installation work, a certificate of completion of power transmission cable installation, photographs of the installation works, and the operation manual for the diesel engine. (NEDO)

Demonstration and Optimization of BNFL's Pulsed Jet Mixing and RFD Sampling Systems Using NCAW Simulant

International Nuclear Information System (INIS)

Bontha, J.R.; Golcar, G.R.; Hannigan, N.

2000-01-01

The BNFL Inc. flowsheet for the pretreatment and vitrification of the Hanford High Level Tank waste includes the use of several hundred Reverse Flow Diverters (RFDs) for sampling and transferring the radioactive slurries and Pulsed Jet mixers to homogenize or suspend the tank contents. The Pulsed Jet mixing and the RFD sampling devices represent very simple and efficient methods to mix and sample slurries, respectively, using compressed air to achieve the desired operation. The equipment has no moving parts, which makes them very suitable for mixing and sampling highly radioactive wastes. However, the effectiveness of the mixing and sampling systems are yet to be demonstrated when dealing with Hanford slurries, which exhibit a wide range of physical and theological properties. This report describes the results of the testing of BNFL's Pulsed Jet mixing and RFD sampling systems in a 13-ft ID and 15-ft height dish-bottomed tank at Battelle's 336 building high-bay facility using AZ-101/102 simulants containing up to 36-wt% insoluble solids. The specific objectives of the work were to: Demonstrate the effectiveness of the Pulsed Jet mixing system to thoroughly homogenize Hanford-type slurries over a range of solids loading; Minimize/optimize air usage by changing sequencing of the Pulsed Jet mixers or by altering cycle times; and Demonstrate that the RFD sampler can obtain representative samples of the slurry up to the maximum RPP-WTP baseline concentration of 25-wt%

Demonstration of an Emergency Containment System

International Nuclear Information System (INIS)

Flanagan, T.M.; Rogers, M.L.; Wilkes, W.R.

1978-01-01

A system called an Emergency Containment System (ECS) to be used for tertiary containment of tritium was reported at the 13th Air Cleaning Conference. This system was part of the Tritium Effluent Control Laboratory then under construction at Mound Facility. A series of experiments has recently been conducted to evaluate the performance of an ECS in capturing tritium accidentally released into an operating laboratory. The ECS is an automatically actuated laboratory air detritiation system utilizing a catalytic oxidation reactor and presaturated oxide adsorption/exchange columns. In the event of an accidental release of tritium into the laboratory, the ECS is automatically activated, and quick-acting pneumatic dampers divert the laboratory air supply and exhaust through the ECS until room concentrations are returned to safe operating levels. The results of the experiments have shown that a tertiary containment of tritium is feasible. In the event of a catastrophic accident, the ECS is capable of preventing the release of a large quantity of tritium to the environment

78 FR 17450 - Notice of Issuance of Materials License Renewal, Operating License SUA-1341, Uranium One USA, Inc...

Science.gov (United States)

2013-03-21

... License Renewal, Operating License SUA-1341, Uranium One USA, Inc., Willow Creek Uranium In Situ Recovery.... SUA- 1341 to Uranium One USA, Inc. (Uranium One) for its Willow Creek Uranium In Situ Recovery (ISR... Commission License No. SUA-1341 For Uranium One USA, Inc., Irigaray and Christensen Ranch Projects (Willow...

Diseases and pests in biomass production systems

International Nuclear Information System (INIS)

Royle, D.J.; Hunter, Tom; McNabb, H.S. Jr.

1998-01-01

The current status of disease and pest problems in willow and poplar biomass systems for energy within Canada, Sweden, the United Kingdom and the United States is described. The IEA Disease and Pest Activities within the recent Task XII (1995-1997), and previous Tasks since 1987, have provided outstanding opportunities for international co-operation which has served substantially to augment national research programmes. Work is described on recognizing different forms of an insect pest or pathogen and understanding the genetic basis of its variability, which is of fundamental importance in developing pest management strategies that exclude inputs of energy-rich materials such as pesticides. Options for more natural pest control are considered including breeding for resistance, plantation designs based on host genotype diversity and biological control 16 refs, 2 figs

Evaluation of Smart Grid Technologies Employed for System Reliability Improvement: Pacific Northwest Smart Grid Demonstration Experience

Energy Technology Data Exchange (ETDEWEB)

Agalgaonkar, Yashodhan P.; Hammerstrom, Donald J.

2017-06-01

The Pacific Northwest Smart Grid Demonstration (PNWSGD) was a smart grid technology performance evaluation project that included multiple U.S. states and cooperation from multiple electric utilities in the northwest region. One of the local objectives for the project was to achieve improved distribution system reliability. Toward this end, some PNWSGD utilities automated their distribution systems, including the application of fault detection, isolation, and restoration and advanced metering infrastructure. In light of this investment, a major challenge was to establish a correlation between implementation of these smart grid technologies and actual improvements of distribution system reliability. This paper proposes using Welch’s t-test to objectively determine and quantify whether distribution system reliability is improving over time. The proposed methodology is generic, and it can be implemented by any utility after calculation of the standard reliability indices. The effectiveness of the proposed hypothesis testing approach is demonstrated through comprehensive practical results. It is believed that wider adoption of the proposed approach can help utilities to evaluate a realistic long-term performance of smart grid technologies.

Demonstration of the renal venous system at routine nephroangiography

International Nuclear Information System (INIS)

Nilsson, P.E.; Aspelin, P.; Holtas, S.

1985-01-01

The demonstration of renal veins during routine nephroangiography was retrospectively investigated and blindly scored in 60 patients. Three different types of contrast media were used: one high-osmolar ionic monomeric (metrozoate) and two low-osmolar, the non-ionic monomeric (metrizamide) and the ionic monoacidic dimeric (ioxalate). The renal veins and the inferior vena cava were significantly better and more often demonstrated when ioxaglate was used compared with metrizoate and metrizmide. There was no significant difference between metrizoate and metrizamide. Following semiselective renal artery injection, the main renal veins were demonstrated with a diagnostically acceptable quality with ioxaglate in 76 per cent, with metrizamide in 40 per cent and with metrizoate in 29 per cent. On selective renal artery injection the demonstration of renal veins increased to 85 per cent with ioxaglate and remained unchanged with metrizmide (38%) and metrizoate(26%). Semiselective or selective nephroangiography with ioxaglate at an ordinary dose was in most patients sufficient to allow evaluation of renal vein involvement in disease, rendering high dose selective nephroangiography or selective nephrophlebography unnecessary. A slower diffusion rate of ioxaglate compared with metrizoate and metrizamide is considered to be the major explanation for the better demonstration of the renal veins. (orig.)

System Guidelines for EMC Safety-Critical Circuits: Design, Selection, and Margin Demonstration

Science.gov (United States)

Lawton, R. M.

1996-01-01

Demonstration of safety margins for critical points (circuits) has traditionally been required since it first became a part of systems-level Electromagnetic Compatibility (EMC) requirements of MIL-E-6051C. The goal of this document is to present cost-effective guidelines for ensuring adequate Electromagnetic Effects (EME) safety margins on spacecraft critical circuits. It is for the use of NASA and other government agencies and their contractors to prevent loss of life, loss of spacecraft, or unacceptable degradation. This document provides practical definition and treatment guidance to contain costs within affordable limits.

Runway Incursion Prevention System: Demonstration and Testing at the Dallas/Fort Worth International Airport

Science.gov (United States)

Jones, Denise R.; Quach, Cuong C.; Young, Steven D.

2007-01-01

A Runway Incursion Prevention System (RIPS) was tested at the Dallas-Ft. Worth International Airport (DFW) in October 2000. The system integrated airborne and ground components to provide both pilots and controllers with enhanced situational awareness, supplemental guidance cues, a real-time display of traffic information, and warning of runway incursions in order to prevent runway incidents while also improving operational capability. A series of test runs was conducted using NASA s Boeing 757 research aircraft and a test van equipped to emulate an incurring aircraft. The system was also demonstrated to over 100 visitors from the aviation community. This paper gives an overview of the RIPS, DFW flight test activities, and quantitative and qualitative results of the testing.

Guidance manual for conducting technology demonstration activities

International Nuclear Information System (INIS)

Jolley, R.L.; Morris, M.I.; Singh, S.P.N.

1991-12-01

This demonstration guidance manual has been prepared to assist Martin Marietta Energy Systems, Inc. (Energy Systems), staff in conducting demonstrations. It is prepared in checklist style to facilitate its use and assumes that Energy Systems personnel have project management responsibility. In addition to a detailed step-by-step listing of procedural considerations, a general checklist, logic flow diagram, and several examples of necessary plans are included to assist the user in developing an understanding of the many complex activities required to manage technology demonstrations. Demonstrations are pilot-scale applications of often innovative technologies to determine the commercial viability of the technologies to perform their designed function. Demonstrations are generally conducted on well-defined problems for which existing technologies or processes are less than satisfactory in terms of effectiveness, cost, and/or regulatory compliance. Critically important issues in demonstration management include, but are not limited to, such factors as communications with line and matrix management and with the US Department of Energy (DOE) and Energy Systems staff responsible for management oversight, budgetary and schedule requirements, regulatory compliance, and safety

Guidance manual for conducting technology demonstration activities

Energy Technology Data Exchange (ETDEWEB)

Jolley, Robert L.; Morris, Michael I.; Singh, Suman P.N.

1991-12-01

This demonstration guidance manual has been prepared to assist Martin Marietta Energy Systems, Inc. (Energy Systems), staff in conducting demonstrations. It is prepared in checklist style to facilitate its use and assumes that Energy Systems personnel have project management responsibility. In addition to a detailed step-by-step listing of procedural considerations, a general checklist, logic flow diagram, and several examples of necessary plans are included to assist the user in developing an understanding of the many complex activities required to manage technology demonstrations. Demonstrations are pilot-scale applications of often innovative technologies to determine the commercial viability of the technologies to perform their designed function. Demonstrations are generally conducted on well-defined problems for which existing technologies or processes are less than satisfactory in terms of effectiveness, cost, and/or regulatory compliance. Critically important issues in demonstration management include, but are not limited to, such factors as communications with line and matrix management and with the US Department of Energy (DOE) and Energy Systems staff responsible for management oversight, budgetary and schedule requirements, regulatory compliance, and safety.

Demonstrating demand response from water distribution system through pump scheduling

International Nuclear Information System (INIS)

Menke, Ruben; Abraham, Edo; Parpas, Panos; Stoianov, Ivan

2016-01-01

Highlights: • Water distribution systems can profitably provide demand response energy. • STOR and FFR are financially viable under a wide range of operating conditions. • Viability depends on the pump utilisation and peak price of the electricity tariff. • Total GHG emissions caused by the provision of reserve energy are <300 gCO_2/kW h. • These are lower than those from the major reserve energy provision technologies. - Abstract: Significant changes in the power generation mix are posing new challenges for the balancing systems of the grid. Many of these challenges are in the secondary electricity grid regulation services and could be met through demand response (DR) services. We explore the opportunities for a water distribution system (WDS) to provide balancing services with demand response through pump scheduling and evaluate the associated benefits. Using a benchmark network and demand response mechanisms available in the UK, these benefits are assessed in terms of reduced green house gas (GHG) emissions from the grid due to the displacement of more polluting power sources and additional revenues for water utilities. The optimal pump scheduling problem is formulated as a mixed-integer optimisation problem and solved using a branch and bound algorithm. This new formulation finds the optimal level of power capacity to commit to the provision of demand response for a range of reserve energy provision and frequency response schemes offered in the UK. For the first time we show that DR from WDS can offer financial benefits to WDS operators while providing response energy to the grid with less greenhouse gas emissions than competing reserve energy technologies. Using a Monte Carlo simulation based on data from 2014, we demonstrate that the cost of providing the storage energy is less than the financial compensation available for the equivalent energy supply. The GHG emissions from the demand response provision from a WDS are also shown to be smaller than

The mixed waste landfill integrated demonstration

International Nuclear Information System (INIS)

Burford, T.D.; Williams, C.V.

1994-01-01

The Mixed Waste Landfill Integrated Demonstration (MWLID) focuses on ''in-situ'' characterization, monitoring, remediation, and containment of landfills in arid environments that contain hazardous and mixed waste. The MWLID mission is to assess, demonstrate, and transfer technologies and systems that lead to faster, better, cheaper, and safer cleanup. Most important, the demonstrated technologies will be evaluated against the baseline of conventional technologies and systems. The comparison will include the cost, efficiency, risk, and feasibility of using these innovative technologies at other sites

Demonstration of an 8 × 25-Gb/s optical time-division multiplexing system

Science.gov (United States)

Wang, Dong; Huo, Li; Li, Yunbo; Wang, Lei; Li, Han; Jiang, Xiangyu; Chen, Xin; Lou, Caiyun

2017-11-01

An 8 × 25-Gb/s optical time-division multiplexing (OTDM) system is demonstrated experimentally. The optical pulse source is based on optical frequency comb (OFC) generation and pulse shaping, which can generate nearly chirp-free 25-GHz 1.6-ps optical Gaussian pulse. The eightfold optical time-division demultiplexer consists of a single-driven dual-parallel Mach-Zehnder modulator (DPMZM) and a Mamyshev reshaper. Error-free demultiplexing of 8 × 25-Gb/s back-to-back (B2B) signal with a power penalty of 4.1 dB to 4.4 dB at a bit error rate (BER) of 10-9 is achieved to confirm the performance of the proposed system.

Subsidized project for development of technology in putting photovoltaic power generation system into practice. Report of international joint demonstrative R and D on photovoltaic power generation system; Taiyoko hatsuden system kokusai kyodo jissho kaihatsu hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

The following joint researches are in progress utilizing natural conditions and social systems in Nepal, Mongolia, Thailand, Malaysia and Vietnam for the purpose of enhancing environmental adaptability, reliability, etc., of technologies. (1) Nepal; accelerated demonstrative research utilizing highland conditions, (2) Mongolia; demonstrative research of movable type photovoltaic power generation system, (3) Thailand; demonstrative research of photovoltaic generation system for battery-charging stations, (4) Malaysia; accelerated demonstrative research utilizing tropical conditions, and (5) Vietnam; demonstrative research of hybrid system on photovoltaic power generation and micro hydro power generation. The research assets of (1) and (3) whose researches have been finished were provided gratis for the co-researcher countries. In (5), on the basis of the geographical conditions such as annual average quantity of solar radiation, conduit for water-turbine, energy complementing relation, load demand, and degree of installation difficulty, Trang Village in Vietnam was selected, with a system decided on PV:100 kW/MH:25 kW/control system. The MH is an induction generator. The primary pieces of equipment are a generator, a storage battery, an inverter and a system control panel. (NEDO)

Prominent porto-systemic collateral pathways in patients with portal hypertension: demonstration by gadolinium-enhanced magnetic resonance angiography

International Nuclear Information System (INIS)

Caldana, Rogerio Pedreschi; Bezerra, Alexandre Araujo Sergio; Cecin, Alexnadre Oliveira; Souza, Luis Ronan Marques Ferreira de; Goldman, Susan Menasce; D'Ippolito, Giuseppe; Szejnfeld, Jacob

2003-01-01

To demonstrate the usefulness of gadolinium-enhanced magnetic resonance angiography in the evaluation of prominent porto-systemic collateral pathways. We reviewed the images from 40 patients with portal hypertension studied with gadolinium-enhanced magnetic resonance angiography and selected illustrative cases of prominent porto-systemic collateral pathways. The scans were performed using high field equipment (1.5 Tesla) and a 3 D volume technique. Image were obtained after intravenous injection of paramagnetic contrast media using a power injector. Magnetic resonance angiography demonstrated with precision the porto-systemic collateral pathways, particularly when investigating extensive territories or large vessels. The cases presented show the potential of this method in the investigation of patients with portal hypertension. Gadolinium-enhanced magnetic resonance angiography is a useful method for the evaluation of patients with portal hypertension and prominent collateral pathways. (author)

Comparing annual and perennial crops for bioenergy production - influence on nitrate leaching and energy balance

DEFF Research Database (Denmark)

Pugesgaard, Siri; Schelde, Kirsten; Ugilt Larsen, Søren

2015-01-01

Production of energy crops is promoted as a means to mitigate global warming by decreasing dependency on fossil energy. However, agricultural production of bioenergy can have various environmental effects depending on the crop and production system. In a field trial initiated in 2008, nitrate...... concentration in soil water was measured below winter wheat, grass-clover and willow during three growing seasons. Crop water balances were modelled to estimate the amount of nitrate leached per hectare. In addition, dry matter yields and nitrogen (N) yields were measured, and N balances and energy balances...... was also measured in an old willow crop established in 1996 from which N leaching ranged from 6 to 27 kg ha−1 yr−1. Dry matter yields ranged between 5.9 and 14.8 Mg yr−1 with lowest yield in the newly established willow and the highest yield harvested in grass-clover. Grass-clover gave the highest net...

Development and Deployment of a Short Rotation Woody Crops Harvesting System Based on a Case New Holland Forage Harvester and SRC Woody Crop Header

Energy Technology Data Exchange (ETDEWEB)

Eisenbies, Mark [State Univ. of New York College of Environmental Science and Forestry (SUNY-ESF), Syracuse, NY (United States); Volk, Timothy [State Univ. of New York College of Environmental Science and Forestry (SUNY-ESF), Syracuse, NY (United States); Abrahamson, Lawrence [State Univ. of New York College of Environmental Science and Forestry (SUNY-ESF), Syracuse, NY (United States); Shuren, Richard [GreenWood Resources, Inc., Portland, OR (United States); Stanton, Brian [GreenWood Resources, Inc., Portland, OR (United States); Posselius, John [Case New Holland, New Holland, PA (United States); McArdle, Matt [Mesa Reduction Engineering and Processing, Inc., Auburn, NY (United States); Karapetyan, Samvel [State Univ. of New York College of Environmental Science and Forestry (SUNY-ESF), Syracuse, NY (United States); Patel, Aayushi [State Univ. of New York College of Environmental Science and Forestry (SUNY-ESF), Syracuse, NY (United States); Shi, Shun [State Univ. of New York College of Environmental Science and Forestry (SUNY-ESF), Syracuse, NY (United States); Zerpa, Jose [State Univ. of New York College of Environmental Science and Forestry (SUNY-ESF), Syracuse, NY (United States)

2014-10-03

Biomass for biofuels, bioproducts and bioenergy can be sourced from forests, agricultural crops, various residue streams, and dedicated woody or herbaceous crops. Short rotation woody crops (SRWC), like willow and hybrid poplar, are perennial cropping systems that produce a number of environmental and economic development benefits in addition to being a renewable source of biomass that can be produced on marginal land. Both hybrid poplar and willow have several characteristics that make them an ideal feedstock for biofuels, bioproducts, and bioenergy; these include high yields that can be obtained in three to four years, ease of cultivar propagation from dormant cuttings, a broad underutilized genetic base, ease of breeding, ability to resprout after multiple harvests, and feedstock composition similar to other sources of woody biomass. Despite the range of benefits associated with SRWC systems, their deployment has been restricted by high costs, low market acceptance associated with inconsistent chip quality (see below for further explanation), and misperceptions about other feedstock characteristics (see below for further explanation). Harvesting of SRWC is the largest single cost factor (~1/3 of the final delivered cost) in the feedstock supply system. Harvesting is also the second largest input of primary fossil energy in the system after commercial N fertilizer, accounting for about one third of the input. Therefore, improving the efficiency of the harvesting system has the potential to reduce both cost and environmental impact. At the start of this project, we projected that improving the overall efficiency of the harvesting system by 25% would reduce the delivered cost of SRWC by approximately $0.50/MMBtu (or about $7.50/dry ton). This goal was exceeded over the duration of this project, as noted below.

BAMUD Features Demonstration by System View

Directory of Open Access Journals (Sweden)

D. Kocur

2004-09-01

Full Text Available Direct-sequence code-division multiple access (DS-CDMA is afrequently used wireless technology in DS-CDMA communications. Theconventional DS-CDMA detector follows a single-user detection strategyin which each user is detected separately without regard for the otherusers. The better strategy is multi-user detection (MUD, whereinformation about multiple users is used to improve detection of eachindividual user. This paper presents an adaptive multi-user detectorconverging (for any initialization to the minimum mean square error(MMSE detector without requiring training sequences. This blindmulti-user detector (BAMUD requires no more knowledge than does theconventional single-user detector. The structure of adaptive blinddetector is simulated by the system design tool SystemView. The aimfocus is to verify theoretical knowledge of BAMUD structure usinghardware-oriented PC-based model in SystemView.

European energy crops overview. Country report for Denmark

Energy Technology Data Exchange (ETDEWEB)

Statens Planteavlsforsoeg, Tjele Denmark; Statens Jordbrugstekniske Forsoeg, Horsens Denmark

1996-06-01

Biomass constitutes a significant contribution to the Danish energy production and is a major tool in increasing the contribution from renewables. So far the focus has been on utilizing existing biomass residues like straw and forest residues and not energy crops. The government has agreed to carry out a demonstration and development programme on energy crops in order to analyse aspects of economy, energy, environment, nature conservancy and comerciality. Several plant species have been investigated for their potential as energy crops and overview information in presented on buchina, sunflower, knotweed, Jerusalem artichoke, false flax, reed Canary grass and corn cockle. More detailed descriptions are given on willow, Miscanthus, energy grain (grain whole crop) and rape which have been most intensively investigated. Rape has been the energy crop grown on the largest scale (40-50,000 ha) but the oil has not been used for energy purposes in Denmark. A research programme on the development of a low input production system for non-food rape is currently conducted. The perennial crops willow and Miscanthus are grown with low input of fertilizer and pesticides and are considered environmentally friendly. Willow-SRC is used as fuel at district heating plants, both commercially and for feasibility studies. Full-scale tests have been carried out on Miscanthus combustion in farm heating plant constructed for straw firing, and on co-combustion with coal at power stations. Grain whole crop (energy grain) has been combusted at a district heating plant, a CHP-plant and a power station. Co-combustion with coal was carried out at a CFB-boiler. Concerning ethanol based on energy crops, only a few activities are in progress. (EG) 89 refs.

Buried Waste Integrated Demonstration FY-93 Deployment Plan

International Nuclear Information System (INIS)

Bonnenberg, R.W.; Heard, R.E.; Milam, L.M.; Watson, L.R.

1993-02-01

The Buried Waste Integrated Demonstration (BWID) is a program funded by the US Department of Energy Office of Technology Development. BWID supports the applied research, development, demonstration, and evaluation of a suite of advanced technologies that together form a comprehensive remediation system for the effective and efficient remediation of buried waste. The fiscal year 1993 effort will deploy seven major field demonstrations at the Idaho National Engineering Laboratory's (INEL's) Radioactive Waste Management Complex Cold Test Pit. These major demonstrations are Remote Characterization System, Remote Excavation System, Overburden Removal, Waste Isolation, Contamination Control Unit, Rapid Monitoring Unit, and Fixation of Soil Surface Contamination. This document is the basic operational planning document for BWID deployment of the INEL field demonstrations. Additional sections deal briefly with four nonINEL field and laboratory demonstrations (Buried Waste Retrieval, Arc Melter Vitrification, Graphite DC Plasma Arc Melter, and Fixed Hearth Plasma Process) and with four INEL laboratory demonstrations (Electrostatic Curtain, Thermal Kinetics, Multiaxis Crane Control System, and Dig-Face Characterization)

Central Radar System, Over-the-Horizon Backscatter

Science.gov (United States)

1990-03-09

Magnolia virginiana Switchgrass Panicum virgatum FAC+ Tall mannagrass Glyceria grandis OBL Water fern Salvinia spp. and Marsilea vestita OBL Water...boxelder, (Acer negundo), oaks (Quercus spp.), willows (Salix spp.), chokecherry (Prunus virginiana ), plum (Prunus spp.), and russian olive (Elaeagnus...maintenance of the power lines may be required to trim or prune trees which may interfere with the lines. With the exception of the pole sites, the only

IGCC technology and demonstration

Energy Technology Data Exchange (ETDEWEB)

Palonen, J [A. Ahlstrom Corporation, Karhula (Finland). Hans Ahlstrom Lab.; Lundqvist, R G [A. Ahlstrom Corporation, Helsinki (Finland); Staahl, K [Sydkraft AB, Malmoe (Sweden)

1997-12-31

Future energy production will be performed by advanced technologies that are more efficient, more environmentally friendly and less expensive than current technologies. Integrated gasification combined cycle (IGCC) power plants have been proposed as one of these systems. Utilising biofuels in future energy production will also be emphasised since this lowers substantially carbon dioxide emissions into the atmosphere due to the fact that biomass is a renewable form of energy. Combining advanced technology and biomass utilisation is for this reason something that should and will be encouraged. A. Ahlstrom Corporation of Finland and Sydkraft AB of Sweden have as one part of company strategies adopted this approach for the future. The companies have joined their resources in developing a biomass-based IGCC system with the gasification part based on pressurised circulating fluidized-bed technology. With this kind of technology electrical efficiency can be substantially increased compared to conventional power plants. As a first concrete step, a decision has been made to build a demonstration plant. This plant, located in Vaernamo, Sweden, has already been built and is now in commissioning and demonstration stage. The system comprises a fuel drying plant, a pressurised CFB gasifier with gas cooling and cleaning, a gas turbine, a waste heat recovery unit and a steam turbine. The plant is the first in the world where the integration of a pressurised gasifier with a gas turbine will be realised utilising a low calorific gas produced from biomass. The capacity of the Vaernamo plant is 6 MW of electricity and 9 MW of district heating. Technology development is in progress for design of plants of sizes from 20 to 120 MWe. The paper describes the Bioflow IGCC system, the Vaernamo demonstration plant and experiences from the commissioning and demonstration stages. (orig.)

IGCC technology and demonstration

Energy Technology Data Exchange (ETDEWEB)

Palonen, J. [A. Ahlstrom Corporation, Karhula (Finland). Hans Ahlstrom Lab.; Lundqvist, R.G. [A. Ahlstrom Corporation, Helsinki (Finland); Staahl, K. [Sydkraft AB, Malmoe (Sweden)

1996-12-31

Future energy production will be performed by advanced technologies that are more efficient, more environmentally friendly and less expensive than current technologies. Integrated gasification combined cycle (IGCC) power plants have been proposed as one of these systems. Utilising biofuels in future energy production will also be emphasised since this lowers substantially carbon dioxide emissions into the atmosphere due to the fact that biomass is a renewable form of energy. Combining advanced technology and biomass utilisation is for this reason something that should and will be encouraged. A. Ahlstrom Corporation of Finland and Sydkraft AB of Sweden have as one part of company strategies adopted this approach for the future. The companies have joined their resources in developing a biomass-based IGCC system with the gasification part based on pressurised circulating fluidized-bed technology. With this kind of technology electrical efficiency can be substantially increased compared to conventional power plants. As a first concrete step, a decision has been made to build a demonstration plant. This plant, located in Vaernamo, Sweden, has already been built and is now in commissioning and demonstration stage. The system comprises a fuel drying plant, a pressurised CFB gasifier with gas cooling and cleaning, a gas turbine, a waste heat recovery unit and a steam turbine. The plant is the first in the world where the integration of a pressurised gasifier with a gas turbine will be realised utilising a low calorific gas produced from biomass. The capacity of the Vaernamo plant is 6 MW of electricity and 9 MW of district heating. Technology development is in progress for design of plants of sizes from 20 to 120 MWe. The paper describes the Bioflow IGCC system, the Vaernamo demonstration plant and experiences from the commissioning and demonstration stages. (orig.)

Bluetooth wireless monitoring, diagnosis and calibration interface for control system of fuel cell bus in Olympic demonstration

Energy Technology Data Exchange (ETDEWEB)

Hua, Jianfeng; Lin, Xinfan; Xu, Liangfei; Li, Jianqiu; Ouyang, Minggao [Tsinghua University, State Key Laboratory of Automotive Safety and Energy, Beijing100084 (China)

2009-01-15

With the worldwide deterioration of the natural environment and the fossil fuel crisis, the possible commercialization of fuel cell vehicles has become a hot topic. In July 2008, Beijing started a clean public transportation plan for the 29th Olympic games. Three fuel cell city buses and 497 other low-emission vehicles are now serving the Olympic core area and Beijing urban areas. The fuel cell buses will operate along a fixed bus line for 1 year as a public demonstration of green energy vehicles. Due to the specialized nature of fuel cell engines and electrified power-train systems, measurement, monitoring and calibration devices are indispensable. Based on the latest Bluetooth wireless technology, a novel Bluetooth universal data interface was developed for the control system of the fuel cell city bus. On this platform, a series of wireless portable control auxiliary systems have been implemented, including wireless calibration, a monitoring system and an in-system programming platform, all of which are ensuring normal operation of the fuel cell buses used in the demonstration. (author)

Performance analysis of an optical self-interference cancellation system with a directly modulated laser-based demonstration.

Science.gov (United States)

Yu, Yinghong; Zhang, Yunhao; Huang, Lin; Xiao, Shilin

2018-02-20

In this paper, two main performance indices of the optical self-interference cancellation (OSIC) system are theoretically analyzed: cancellation bandwidth and depth. Delay deviation is investigated to be the determining factor of cancellation bandwidth, based on which the bandwidth advantage of the OSIC system over electrical schemes is also proven theoretically. Cancellation depth in the narrowband is mostly influenced by attenuation and delay-adjusting deviation, while in the broadband case, the performance is mostly limited by frequency-dependent amplitude and phase mismatch. The cancellation performance analysis is suitable for most linear modulation-demodulation OSIC systems, including the directly modulated laser (DML)-based OSIC system verified experimentally in this paper. The cancellation model is well demonstrated by the agreement between experimental cancellation results and predicted performance. For over-the-air demonstration with the employment of antennas, broadband cancellation within 450 MHz bandwidth of 22 dB and 25 dB is achieved at 900 MHz and 2.4 GHz, respectively. In addition, orthogonal frequency division multiplexing signals are employed to show in-band full-duplex transmission with good performance by the DML-based OSIC system, with successful suppression of self-interference and recovery of the signal of interest.

A Demonstration System for Capturing Geothermal Energy from Mine Waters beneath Butte, Montana

Energy Technology Data Exchange (ETDEWEB)

Blackketter, Donald [Montana Tech of the Univ. of Montana, Butte, MT (United States)

2015-06-01

Executive Summary An innovative 50-ton ground-source heat pump (GSHP) system was installed to provide space heating and cooling for a 56,000 square foot (5,200 square meter) building in Butte Montana, in conjunction with its heating and chiller systems. Butte is a location with winter conditions much colder than the national average. The GSHP uses flooded mine waters at 78F (25C) as the heat source and heat sink. The heat transfer performance and efficiency of the system were analyzed using data from January through July 2014. This analysis indicated that for typical winter conditions in Butte, Montana, the GSHP could deliver about 88% of the building’s annual heating needs. Compared with a baseline natural-gas/electric system, the system demonstrated at least 69% site energy savings, 38% source energy savings, 39% carbon dioxide emissions reduction, and a savings of $17,000 per year (40%) in utility costs. Assuming a $10,000 per ton cost for installing a production system, the payback period at natural gas costs of $9.63/MMBtu and electricity costs of $0.08/kWh would be in the range of 40 to 50 years. At higher utility prices, or lower installation costs, the payback period would obviously be reduced.

Experimental-demonstrative system for energy conversion using hydrogen fuel cell - preliminary results

International Nuclear Information System (INIS)

Stoenescu, D.; Stefanescu, I.; Patularu, I.; Culcer, M.; Lazar, R.E.; Carcadea, E.; Mirica, D. . E-mail address of corresponding author: daniela@icsi.ro; Stoenescu, D.)

2005-01-01

It is well known that hydrogen is the most promising solution of future energy, both for long and medium term strategies. Hydrogen can be produced using many primary sources (natural gas, methane, biomass, etc.), it can be burned or chemically react having a high yield of energy conversion, being a non-polluted fuel. This paper presents the preliminary results obtained by ICSI Rm. Valcea in an experimental-demonstrative conversion energy system made by a sequence of hydrogen purification units and a CO removing reactors until a CO level lower than 10ppm, that finally feeds a hydrogen fuel stack. (author)

A readout system for the micro-vertex-detector demonstrator for the CBM experiment at FAIR

Energy Technology Data Exchange (ETDEWEB)