Model for RHIC ramp controls

International Nuclear Information System (INIS)

Kewisch, J.; Mane, V.; Clifford, T.; Hartmann, H.; Kahn, T.; Oerter, B.; Peggs, S.

1994-01-01

This paper introduces the hardware and software concepts for the implementation of the ramp controls. The hardware part of the ramp controls consists of a number of multi-purpose Wave Form Generators (WFGS) which control the settings of accelerator hardware directly or indirectly by controlling their WFG. A Real Time Data Link (RTDL) data transfer system connects the WFGs in a three layer architecture. To the usual two layers which generate an independent timing signal and dependent set points, respectively, an intermediate layer is added which produces accelerator parameters such as the magnet strength. The task of the bottom layer is therefore reduced to the function of implementing those parameters. This architecture de-couples two independent functions which axe normally folded together. The function of the hardware becomes modular and easily maintainable. The ramp control software is layered in the same way. Between the top layer (the ramp procedure application program) and the bottom layer (the hardware interface) an additional layer of ''manager'' programs allow operation of accelerator subsystems

Lean Application to Manufacturing Ramp-Up

DEFF Research Database (Denmark)

Christensen, Irene; Rymaszewska, Anna

2016-01-01

. Abstracting from the extant literature, the authors considered the competitiveness of manufacturing companies from two principal perspectives: the leanness of the ramp-up process and the new-value creation of quality managers. While much of the literature fails to acknowledge that the roots of lean actually......This article provides a theoretical overview of the concepts of lean and manufacturing ramp-up in an attempt to conceptualize the strategic areas in which lean philosophy and principles can be applied for continuous improvements. The application of lean principles during the final stage of a new...... product development process, that is, the ramp-up process, is a critical, early enabler of lean manufacturing. The manufacturing strategy literature conceptualizes a state of “leanness in operations,” which can consolidate both the concepts of lean and manufacturing ramp-up, providing a dual perspective...

AN ACCURATE MODELING OF DELAY AND SLEW METRICS FOR ON-CHIP VLSI RC INTERCONNECTS FOR RAMP INPUTS USING BURR’S DISTRIBUTION FUNCTION

Directory of Open Access Journals (Sweden)

Rajib Kar

2010-09-01

Full Text Available This work presents an accurate and efficient model to compute the delay and slew metric of on-chip interconnect of high speed CMOS circuits foe ramp input. Our metric assumption is based on the Burr’s Distribution function. The Burr’s distribution is used to characterize the normalized homogeneous portion of the step response. We used the PERI (Probability distribution function Extension for Ramp Inputs technique that extends delay metrics and slew metric for step inputs to the more general and realistic non-step inputs. The accuracy of our models is justified with the results compared with that of SPICE simulations.

40 CFR 1033.520 - Alternative ramped modal cycles.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 32 2010-07-01 2010-07-01 false Alternative ramped modal cycles. 1033... cycles. (a) Locomotive testing over a ramped modal cycle is intended to improve measurement accuracy at... locomotive notch settings. Ramped modal cycles combine multiple test modes of a discrete-mode steady-state...

Implementation of Ramp Control in RHIC

International Nuclear Information System (INIS)

Kewisch, J.

1999-01-01

After the injection of beam into RHIC the beam energy is ramped from 10.8 GeV/u to 108 GeV/u and the beta function of the interaction points is reduced from 10 meters to 1 meter. The set points for magnet power supplies and RF cavities is changed during such ramps in concert. A system of Wave Form Generators (WFGs), interconnected by a Real Time Data Link (RTDL) and Event Link is used to control these devices. RHIC ramps use a two level system of WFGs: one transmits the beam energy and a ''pseudo time'' variable as functions of time via RTDL; the other calculates the device set points as functions of these RTDL variables. Energy scaling, saturation correction and the wiring of interaction region quadruples is performed on the second level. This report describes the configuration and implementation of the software, firmware and hardware of the RHIC ramp system

OXYGEN UPTAKE KINETICS DURING INCREMENTAL- AND DECREMENTAL-RAMP CYCLE ERGOMETRY

Directory of Open Access Journals (Sweden)

Fadıl Özyener

2011-09-01

Full Text Available The pulmonary oxygen uptake (VO2 response to incremental-ramp cycle ergometry typically demonstrates lagged-linear first-order kinetics with a slope of ~10-11 ml·min-1·W-1, both above and below the lactate threshold (ӨL, i.e. there is no discernible VO2 slow component (or "excess" VO2 above ӨL. We were interested in determining whether a reverse ramp profile would yield the same response dynamics. Ten healthy males performed a maximum incremental -ramp (15-30 W·min-1, depending on fitness. On another day, the work rate (WR was increased abruptly to the incremental maximum and then decremented at the same rate of 15-30 W.min-1 (step-decremental ramp. Five subjects also performed a sub-maximal ramp-decremental test from 90% of ӨL. VO2 was determined breath-by-breath from continuous monitoring of respired volumes (turbine and gas concentrations (mass spectrometer. The incremental-ramp VO2-WR slope was 10.3 ± 0.7 ml·min-1·W-1, whereas that of the descending limb of the decremental ramp was 14.2 ± 1.1 ml·min-1·W-1 (p < 0.005. The sub-maximal decremental-ramp slope, however, was only 9. 8 ± 0.9 ml·min-1·W-1: not significantly different from that of the incremental-ramp. This suggests that the VO2 response in the supra-ӨL domain of incremental-ramp exercise manifest not actual, but pseudo, first-order kinetics

9 CFR 313.1 - Livestock pens, driveways and ramps.

Science.gov (United States)

2010-01-01

... 9 Animals and Animal Products 2 2010-01-01 2010-01-01 false Livestock pens, driveways and ramps... INSPECTION AND CERTIFICATION HUMANE SLAUGHTER OF LIVESTOCK § 313.1 Livestock pens, driveways and ramps. (a) Livestock pens, driveways and ramps shall be maintained in good repair. They shall be free from sharp or...

SUPER-RAMP PK2 cases by START-3. Preliminary Report

International Nuclear Information System (INIS)

Novikov, Vladimir; Kuznetsov, Vladimir; Chulkin, Dmitriy

2013-01-01

The Studsvik SUPER-RAMP Project, an internationally sponsored research project, investigated the failure propensity of typical LWR fuel in the form of test rods when subjected to power ramps, after base irradiation to high burn-up. The following information summarizing the project is abstracted from the Final Report of the SUPER-RAMP project (STSR-32). The Project power ramped 28 individual PWR rods and 16 BWR rods. The PWR rods were all tested using high ramp rates. Due to different objectives for the BWR subprogramme, one set of the BWR rods was tested using a high ramp rate, and another set were tested with a very slow ramp rate. All rods underwent a thorough examination programme, comprising characterisation prior to base irradiation, examination between base and ramp irradiation and examination after ramp irradiation. This consisted of 6 groups of rods with variations in design and material parameters. The rods were base irradiated in a power reactor environment KK Obrigheim or BR-3 at time averaged heat ratings mainly in the range 14-26 kW/m to peak burn-ups in the range 33-45 MWd/kgU and were subsequently ramp tested in the research reactor R2 at Studsvik, Sweden. The result can be summarized as follows: In this document some calculations are made on the PK2 group fuel rods. The rods were standard rods manufactured by Kraftwerk Union AG/Combustion Engineering (KWU/CE). All these rods sustained ramping to power levels in the range 41 to 49 kW/m and power changes 16-24 kW/m without failure, in spite of large deformations, fuel restructuring and fission gas release particularly for the PK2 rods. Though the results of this paper seem to be based on the incomplete dataset (ambiguity in power raise rates, undefined fuel pellet and cladding surface roughness), we think that START-3 Zircalloy-4 model requires further improvements. In order to do them, we kindly ask IAEA to provide us with more detailed irradiation histories (more than 3 axial zones, power increase

RAMP 2005 technical report

International Nuclear Information System (INIS)

2006-01-01

This technical report provided details of all monitoring activities conducted by the Regional Aquatics Monitoring Program (RAMP), which was initiated in 1997 to examine the impacts of oil sands mining development on aquatic systems in the region. RAMP's objective is to integrate aquatic monitoring activities in order to identify long-term trends and regional issues related to the environment in the Regional Municipality of Wood Buffalo. In 2005, RAMP focused on key components of boreal aquatic ecosystems. This report provided full outlines of all climate and hydrology monitoring activities; water and sedimentation analyses; and studies of benthic communities in rivers, lakes, and deltas. Sets of measurements endpoints were used to represent the health and integrity of valued environmental resources. Satellite imager was used to estimate activities related to oil sands developments. The report was divided into subsections which related monitoring activities for various rivers and tributaries in the region. Small and negligible calculated changes were observed in hydrologic conditions in the Athabasca River mainstem. No discernible changes in water and sediment quality were observed that could positively be ascribed to oil sands developments in the region. Very little evidence suggested that fish populations had changed as a result of increased activities in the region. The influence of oil sands development activities on the aquatic resources of the Athabasca River mainstem were minor and mostly undetectable. The results of fish tissue studies from the lower Athabasca River showed that concentrations of mercury in fish tissues occurred at levels that posed a high risk to subsistence fishers. A higher number of metal concentrations in some lakes in the region was attributed to natural causes. The results of a sentinel species monitoring program conducted at the Ells River watershed were also included. Recommendations for further refining RAMP programs were also

Quantum strongly secure ramp secret sharing

DEFF Research Database (Denmark)

Zhang, Paul; Matsumoto, Rytaro Yamashita

2015-01-01

Quantum secret sharing is a scheme for encoding a quantum state (the secret) into multiple shares and distributing them among several participants. If a sufficient number of shares are put together, then the secret can be fully reconstructed. If an insufficient number of shares are put together...... however, no information about the secret can be revealed. In quantum ramp secret sharing, partial information about the secret is allowed to leak to a set of participants, called an unqualified set, that cannot fully reconstruct the secret. By allowing this, the size of a share can be drastically reduced....... This paper introduces a quantum analog of classical strong security in ramp secret sharing schemes. While the ramp secret sharing scheme still leaks partial information about the secret to unqualified sets of participants, the strong security condition ensures that qudits with critical information can...

START-3 calculations of SUPER-RAMP (FUMEX-III) cases

International Nuclear Information System (INIS)

Chulkin, D.; Kuznetsov, V.; Krupkin, A.; Bogatyr, S.; Novikov, V.

2011-01-01

The Studsvik SUPER-RAMP Project, an internationally sponsored research project, investigated the failure propensity of typical LWR fuel in the form of test rods when subjected to power ramps, after base irradiation. The Project power ramped 28 individual PWR rods and 16 BWR rods. The PWR rods were all tested using high ramp rates. Due to different objectives for the BWR subprogram, one set of the BWR rods was tested using a high ramp rate, and another set were tested with a very slow ramp rate. The rods were base irradiated in a power reactor environment KK Obrigheim or BR-3 at time averaged heat ratings mainly in the range 14-26 kW/m to peak bum-ups in the range 33-45 MWd/kgU and were subsequently ramp tested in the research reactor R2 at Studsvik, Sweden. In this presentation some calculations are made on the PK2 group fuel rods. The rods were standard rods manufactured by Kraftwerk Union AG/Combustion Engineering (KWU/CE). Calculations have shown reasonable coincidence of calculated and experimental FGR and reasonable prediction of dimensional behavior of fuel rod. Following the lead taken in the original FUMEX CRP, a number of simplified cases were constructed in order to investigate mathematical stability and more easily compare model and code predictions without the vagaries of real power histories. In this presentation, each case is outlined together with the reason for its inclusion before presenting the results and comparing the predictions

Wind Plant Ramping Behavior

Energy Technology Data Exchange (ETDEWEB)

Ela, E.; Kemper, J.

2009-12-01

With the increasing wind penetrations, utilities and operators (ISOs) are quickly trying to understand the impacts on system operations and planning. This report focuses on ramping imapcts within the Xcel service region.

Steady squares and hexagons on a subcritical ramp

International Nuclear Information System (INIS)

Hoyle, R.B.

1995-01-01

Steady squares and hexagons on a subcritical ramp are studied, both analytically and numerically, within the framework of the lowest-order amplitude equations. On the subcritical ramp, the external stress or control parameter varies continuously in space from subcritical to supercritical values. At the subcritical end of the ramp, pattern formation is suppressed, and patterns fade away into the conduction solution. It is shown that three-dimensional patterns may change shape on a subcritical ramp. A square pattern becomes a pattern of rolls as it fades, with the roll axes aligned in the direction orthogonal to that in which the control parameter varies. Hexagons in systems with horizontal midplane symmetry become a pattern of rectangles before reaching the conduction solution. There is a suggestion that hexagons in systems which lack this symmetry might fade away through a roll pattern. Numerical simulations are used to illustrate these phenomena

Nuclear and thermal power plant power ramping capability

International Nuclear Information System (INIS)

Golovach, E.A.

1983-01-01

The possibilities of step power increase by NPP and TPP units under emergency conditions of power grids operation are considered. The data analysis has shown that power units ramping capability with WWER-440, WWER-1000 and RBMK-1000 reactors is higher than that of 300 MW power units on fossil fuel, at the initial time interval (0-30 s). These NPP power units satisfy as to ramping capability the energy system requirements. Higher NPP power units ramping capability is explained by the fact that relative pressure before turbine valves is decreased less than in straight-through boilers while the steam volumes time constant of steam separator-superheaters is less than that of intermediate superheatings. Higher power unit ramping capability with WWER-440 and RBMK-1000 reactors as compared with the WWER-1000 reactor is pointed out as well as the increase of WWER-1000 power unit capability using high-speed turbines

Microprocessor-controlled, programmable ramp voltage generator

International Nuclear Information System (INIS)

Hopwood, J.

1978-11-01

A special-purpose voltage generator has been developed for driving the quadrupole mass filter of a residual gas analyzer. The generator is microprocessor-controlled with desired ramping parameters programmed by setting front-panel digital thumb switches. The start voltage, stop voltage, and time of each excursion are selectable. A maximum of five start-stop levels may be pre-selected for each program. The ramp voltage is 0 to 10 volts with sweep times from 0.1 to 999.99 seconds

Prediction of power-ramp defects in CANDU fuel

International Nuclear Information System (INIS)

Gillespie, P.; Wadsworth, S.; Daniels, T.

2010-01-01

Power ramps result in fuel pellet expansion and can lead to fuel sheath failures by fission product induced stress corrosion cracking (SCC). Historically, empirical models fit to experimental test data were used to predict the onset of power-ramp failures in CANDU fuel. In 1988, a power-ramped fuel defect event at PNGS-1 led to the refinement of these empirical models. This defect event has recently been re-analyzed and the empirical model updated. The empirical model is supported by a physically based model which can be used to extrapolate to fuel conditions (density, burnup) outside of the 1988 data set. (author)

Confinement and transport properties during current ramps in the ASDEX Upgrade tokamak

Science.gov (United States)

Fable, E.; Angioni, C.; Hobirk, J.; Pereverzev, G.; Fietz, S.; Hein, T.; ASDEX Upgrade Team

2011-04-01

A detailed analysis of experimental data from the ASDEX Upgrade tokamak is carried out to shed light on the properties of confinement and transport in the current ramp-up and ramp-down phases of the plasma discharge. The experimental database is used to identify the relevant ranges of parameters explored during the ramp-up and the ramp-down. The energy confinement time observed in the two ramps displays interesting evolution, in many cases attaining different values at the same current level between ramp-up and ramp-down. The possible reasons for this behaviour are investigated. Interpretative transport simulations are used as a tool to clarify the interplay between different parameters, which are coupled in a non-linear way. In addition, a theory-based transport model is used to understand the behaviour of confinement as observed in the experiment, evidencing the role of both turbulent and neoclassical transport. Linear gyrokinetic calculations are performed to identify the relevant turbulence regime, showing that a broad range of frequencies, in the trapped electron modes (TEMs) and in the ion temperature gradient modes (ITGs) regimes, is explored during both the ramp-up and ramp-down. In the same framework, a quasi-linear model is applied to calculate the value of the local logarithmic density gradient and compare it with the experimental value. Finally, first non-linear simulations of heat transport during the current ramps are presented.

Ramp metering with an objective to reduce fuel consumption

OpenAIRE

Vreeswijk, Jacob Dirk; Woldeab, Zeremariam; de Koning, Anne; Bie, Jing

2011-01-01

Ramp meters successfully decrease congestion but leave a burden on the traffic situation at on-ramps. Chaotic queuing leads to many stop-and-go movements and causes inefficiency where fuel consumption is concerned. As part of the eCoMove project, complementary strategies are being designed and evaluated to reduce fuel consumption at metered on-ramps, using vehicle-to-infrastructure communication. This paper presents the design of two strategies, as well as their effect as derived from simulat...

A criterion and mechanism for power ramp defects

International Nuclear Information System (INIS)

Garlick, A.; Gravenor, J.G.

1978-02-01

The problem of power ramp defects in water reactor fuel pins is discussed in relation to results recently obtained from ramp experiments in the Steam Generating Heavy Water Reactor. Cladding cracks in the defected fuel pins were similar, both macro- and micro structurally, to those in unirradiated Zircaloy exposed to iodine stress-corrosion cracking (scc) conditions. Furthermore, when the measured stress levels for scc in short-term tests were taken as a criterion for ramp defects, UK fuel modelling codes were found to give a useful indication of defect probability under reactor service conditions. The likelihood of sticking between fuel and cladding is discussed and evidence presented which suggests that even at power a degree of adhesion may be expected in some fuel pins. The ramp defect mechanism is discussed in terms of fission product scc, initiation being by intergranular penetration and propagation by cleavage when suitably orientated grains are exposed to large dilatational stresses ahead of the main crack. (author)

Ramp generator circuit for probe diagnostics using microcontroller for LHCD system

International Nuclear Information System (INIS)

Virani, C G; Sharma, P K

2010-01-01

It is well known that in LHCD system, the rf power coupling between antenna and plasma strongly depends on the edge plasma parameter. Thus it is mandatory to monitor edge plasma parameter to establish proper impedance matching condition when LHCD power is launched into the plasma. For SST1 LHCD system, we intend to monitor the edge plasma parameter employing electric probes, connected to the grill antenna sides for the said purpose. In SST1, initially LHCD system would couple rf power to plasmas lasting for small durations. Gradually the power and pulse length would be increased to eventually get 1000 seconds plasma. To monitor the edge plasma parameter, over such a wide spectrum (say few millisecond to seconds) during the above campaign, a flexible measurement scheme is desired which would cater to entire spectrum of operation. Normally a ramp is utilized to bias the electric probe, which yields various plasma parameters. To cater our requirement, the ramp generator must have facility to change ramp-up rate to meet our pulse length requirement. Further during SST operation, the human access near the machine would not be permitted and ramp circuit might not be accessible for manual settings. Thus remote setting facility to change ramp-up rate is also desired. Keeping these constraints in mind, a ramp circuit has been designed using Analog Device micro-controller ADuC842. The circuit has both manual and remote setting facility. Ramp generator parameters like Ramp-up rate, Trigger mode, number of cycles, etc. can be set from PC through RS-485 serial link. Initially low voltage (0-5V) ramp signal is generated using micro-controller and inbuilt DAC. This low voltage ramp is then amplified with PA-85 op-amp to get desired probe biasing voltage (-110V to +110V). The ramp period can be change form (1ms to 1000 ms) to cater to different plasma pulse length. Programming for micro-controller is done in structured language-C with the help of ''Keil'' IDE. In this paper, a

Ramp generator circuit for probe diagnostics using microcontroller for LHCD system

Energy Technology Data Exchange (ETDEWEB)

Virani, C G; Sharma, P K, E-mail: cgvirani@ipr.res.i [Institute for Plasma Research, Bhat, Gandhinagar 382428 (India)

2010-02-01

It is well known that in LHCD system, the rf power coupling between antenna and plasma strongly depends on the edge plasma parameter. Thus it is mandatory to monitor edge plasma parameter to establish proper impedance matching condition when LHCD power is launched into the plasma. For SST1 LHCD system, we intend to monitor the edge plasma parameter employing electric probes, connected to the grill antenna sides for the said purpose. In SST1, initially LHCD system would couple rf power to plasmas lasting for small durations. Gradually the power and pulse length would be increased to eventually get 1000 seconds plasma. To monitor the edge plasma parameter, over such a wide spectrum (say few millisecond to seconds) during the above campaign, a flexible measurement scheme is desired which would cater to entire spectrum of operation. Normally a ramp is utilized to bias the electric probe, which yields various plasma parameters. To cater our requirement, the ramp generator must have facility to change ramp-up rate to meet our pulse length requirement. Further during SST operation, the human access near the machine would not be permitted and ramp circuit might not be accessible for manual settings. Thus remote setting facility to change ramp-up rate is also desired. Keeping these constraints in mind, a ramp circuit has been designed using Analog Device micro-controller ADuC842. The circuit has both manual and remote setting facility. Ramp generator parameters like Ramp-up rate, Trigger mode, number of cycles, etc. can be set from PC through RS-485 serial link. Initially low voltage (0-5V) ramp signal is generated using micro-controller and inbuilt DAC. This low voltage ramp is then amplified with PA-85 op-amp to get desired probe biasing voltage (-110V to +110V). The ramp period can be change form (1ms to 1000 ms) to cater to different plasma pulse length. Programming for micro-controller is done in structured language-C with the help of ''Keil'' IDE

Oil Sands Regional Aquatics Monitoring Program (RAMP) 5 year report

International Nuclear Information System (INIS)

Fawcett, K.

2003-05-01

This 5 year report outlined and examined the activities of the Regional Aquatics Monitoring Program (RAMP) from its introduction in 1997 up to 2001. The RAMP is a multi-stakeholder program comprised of industry and government representatives as well as members of aboriginal groups and environmental organizations. The objectives of RAMP are to monitor aquatic environments in the oil sands region in order to allow for assessment of regional trends and cumulative effects, as well as to provide baseline data against which impact predictions of recent environmental impact assessments can be verified. Scientific programs conducted as part of RAMP during the 5-year period included water quality and sediment quality analyses; fish monitoring; benthic communities monitoring; water quality and aquatic vegetation analyses of wetlands; and hydrology and climate monitoring. RAMP's programs have expanded annually in scope as a result of increased oil sands development in the region. This report provided outlines of RAMP's individual program objectives and organizational structures, as well as details of all studies conducted for each year. Data were collected for all major study areas were presented, and program methodologies for assessing and identifying trends were outlined. refs., tabs., figs

Break up of bound-N-spatial-soliton in a ramp waveguide

NARCIS (Netherlands)

Suryanto, A.; van Groesen, Embrecht W.C.

2002-01-01

We present an analytical and numerical investigation of the propagation of spatial solitons in a nonlinear waveguide with ramp linear refractive index profile (ramp waveguide). For the propagation of a single soliton beam in a ramp waveguide, the particle theory shows that the soliton beam follows a

Assessment on Startup Ramp Rate and Threshold Power of OPR1000

Energy Technology Data Exchange (ETDEWEB)

Kim, Kiyoung; Kim, Yongbae; Cha, Gyunho; Kim, Yongdeog [Korea Hydro and Nuclear Power Co., Ltd., Daejeon (Korea, Republic of)

2014-05-15

This paper summarizes PCI assessment according to several startup ramp rates and threshold power assessment of OPR1000. The definition of threshold power is maximum value in power range that can increase startup ramp rate rapidly. FALCON code is used for PCI assessment and it is analyzed for once-burned fuel because it is the most sensitive to PCI failure. The objective of the PCI analysis is to assess the cladding stress state under various power ramp conditions at the peak power node location. The PCI analyses were conducted for the once-burned fuel from the start of the second cycle to plant power 100%. This paper presents both the PCI analysis according to startup ramp rates and threshold power assessment result like below. · The more startup ramp rate is increased, the more PCI failure probability is decreased in low power range (≤ 40%). · PCI failure is not occurred even though startup ramp rate is 10%/hr until the plant power reaches 55%.

Assessment on Startup Ramp Rate and Threshold Power of OPR1000

International Nuclear Information System (INIS)

Kim, Kiyoung; Kim, Yongbae; Cha, Gyunho; Kim, Yongdeog

2014-01-01

This paper summarizes PCI assessment according to several startup ramp rates and threshold power assessment of OPR1000. The definition of threshold power is maximum value in power range that can increase startup ramp rate rapidly. FALCON code is used for PCI assessment and it is analyzed for once-burned fuel because it is the most sensitive to PCI failure. The objective of the PCI analysis is to assess the cladding stress state under various power ramp conditions at the peak power node location. The PCI analyses were conducted for the once-burned fuel from the start of the second cycle to plant power 100%. This paper presents both the PCI analysis according to startup ramp rates and threshold power assessment result like below. · The more startup ramp rate is increased, the more PCI failure probability is decreased in low power range (≤ 40%). · PCI failure is not occurred even though startup ramp rate is 10%/hr until the plant power reaches 55%

Power ramping/cycling experience and operational recommendations in KWU power plants

International Nuclear Information System (INIS)

Jan, R. von; Wunderlich, F.; Holzer, R.

1980-01-01

The power cycling and ramping experience of KWU is based on experiments in test and commercial reactors, and on evaluation of plant operation (PHWR, PWR and BWR). Power cycling of fuel rods have never lead to PCI failures. In ramping experiments, for fast ramps PCI failure thresholds of 480/420 W/cm are obtained at 12/23 GWd/t(U) burn-up for pressurized PWR fuel. No failures occurred during limited exceedance of the threshold with reduced ramp rate. Operational recommendations used by KWU are derived from experiments and plant experience. The effects of ramping considerations on plant operation is discussed. No rate restrictions are required for start-ups during an operating cycle or load follow operation within set limits for the distortion of the local power distribution. In a few situations, e.g. start-up after refueling, ramp rates of 1 to 5 %/h are recommended depending on plant and fuel design

Portion distortion: typical portion sizes selected by young adults.

Science.gov (United States)

Schwartz, Jaime; Byrd-Bredbenner, Carol

2006-09-01

The incidence of obesity has increased in parallel with increasing portion sizes of individually packaged and ready-to-eat prepared foods as well as foods served at restaurants. Portion distortion (perceiving large portion sizes as appropriate amounts to eat at a single eating occasion) may contribute to increasing energy intakes and expanding waistlines. The purpose of this study was to determine typical portion sizes that young adults select, how typical portion sizes compare with reference portion sizes (based in this study on the Nutrition Labeling and Education Act's quantities of food customarily eaten per eating occasion), and whether the size of typical portions has changed over time. Young adults (n=177, 75% female, age range 16 to 26 years) at a major northeastern university. Participants served themselves typical portion sizes of eight foods at breakfast (n=63) or six foods at lunch or dinner (n=62, n=52, respectively). Typical portion-size selections were unobtrusively weighed. A unit score was calculated by awarding 1 point for each food with a typical portion size that was within 25% larger or smaller than the reference portion; larger or smaller portions were given 0 points. Thus, each participant's unit score could range from 0 to 8 at breakfast or 0 to 6 at lunch and dinner. Analysis of variance or t tests were used to determine whether typical and reference portion sizes differed, and whether typical portion sizes changed over time. Mean unit scores (+/-standard deviation) were 3.63+/-1.27 and 1.89+/-1.14, for breakfast and lunch/dinner, respectively, indicating little agreement between typical and reference portion sizes. Typical portions sizes in this study tended to be significantly different from those selected by young adults in a similar study conducted 2 decades ago. Portion distortion seems to affect the portion sizes selected by young adults for some foods. This phenomenon has the potential to hinder weight loss, weight maintenance, and

Identifying Wind and Solar Ramping Events: Preprint

Energy Technology Data Exchange (ETDEWEB)

Florita, A.; Hodge, B. M.; Orwig, K.

2013-01-01

Wind and solar power are playing an increasing role in the electrical grid, but their inherent power variability can augment uncertainties in power system operations. One solution to help mitigate the impacts and provide more flexibility is enhanced wind and solar power forecasting; however, its relative utility is also uncertain. Within the variability of solar and wind power, repercussions from large ramping events are of primary concern. At the same time, there is no clear definition of what constitutes a ramping event, with various criteria used in different operational areas. Here the Swinging Door Algorithm, originally used for data compression in trend logging, is applied to identify variable generation ramping events from historic operational data. The identification of ramps in a simple and automated fashion is a critical task that feeds into a larger work of 1) defining novel metrics for wind and solar power forecasting that attempt to capture the true impact of forecast errors on system operations and economics, and 2) informing various power system models in a data-driven manner for superior exploratory simulation research. Both allow inference on sensitivities and meaningful correlations, as well as the ability to quantify the value of probabilistic approaches for future use in practice.

Effect of trailing edge ramp on cavity flow structures and pressure drag

International Nuclear Information System (INIS)

Pey, Yin Yin; Chua, Leok Poh; Siauw, Wei Long

2014-01-01

Highlights: • Trailing edge ramps were used to reduce unsteadiness and pressure drag of a cavity. • Proper Orthogonal Decomposition was used to educe the coherent structures. • The 30° ramp was successful in redistributing the energy content within the cavity. • The 30° ramp guides the flow smoothly out of the cavity, reducing flow impingement. • A substantial reduction of pressure drag was achieved by the 30° ramp. -- Abstract: The effects of trailing edge ramp modifications on time-averaged velocity and pressure distributions within a cavity with a length to depth ratio of 2, at a speed of 15 m/s were investigated. The ramp angles were varied at 30°, 45° and 60° and ramp heights were varied at 0.25 times and 0.5 times of cavity depth. The mean flow within the cavity differed significantly from the baseline case when ramp angle was 30° and 45° with ramp height 0.5 times of cavity depth. At these 2 configurations, moment about the center of the cavity floor was reduced significantly. These could be attributed to the more steady flow within the cavity as compared to the baseline case. Spatial correlation of velocity in the cavity of ramp angle 30° showed that internal cavity flow was less sensitive to flow changes in the shear layer as compared to the baseline case. In the same cavity, snapshot Proper Orthogonal Decomposition revealed a redistribution of energy content where energetic structures exist only in the shear layer as opposed to energetic structures in both the shear layer and internal cavity for the baseline case. A reduction of pressure drag was also observed as the gentle ramp angle of 30° guides the flow smoothly out of the cavity and reduces trailing edge impingement

Analysis Balance Parameter of Optimal Ramp metering

Science.gov (United States)

Li, Y.; Duan, N.; Yang, X.

2018-05-01

Ramp metering is a motorway control method to avoid onset congestion through limiting the access of ramp inflows into the main road of the motorway. The optimization model of ramp metering is developed based upon cell transmission model (CTM). With the piecewise linear structure of CTM, the corresponding motorway traffic optimization problem can be formulated as a linear programming (LP) problem. It is known that LP problem can be solved by established solution algorithms such as SIMPLEX or interior-point methods for the global optimal solution. The commercial software (CPLEX) is adopted in this study to solve the LP problem within reasonable computational time. The concept is illustrated through a case study of the United Kingdom M25 Motorway. The optimal solution provides useful insights and guidances on how to manage motorway traffic in order to maximize the corresponding efficiency.

Report on the access to the deposition areas of the repository. Shaft or Ramp?; Utredning roerande tilltraedesvaegar till djupfoervarets deponeringsomraaden. Schakt eller ramp?

Energy Technology Data Exchange (ETDEWEB)

Baeckblom, Goeran [Conrox (Sweden); Christiansson, Rolf; Hedin, Allan; Norman, Fredrik [Swedish Nuclear Fuel and Waste Management Co., Stockholm (Sweden); Lagerstedt, Leif [SwedPower AB, Stockholm (Sweden)

2003-05-01

During year 2002, SKB launched the site-specific engineering of the repository at the Oskarshamn and Oesthammar candidate sites. A part of the ongoing engineering work is to evaluate and possibly select type of access from surface to the underground deposition areas located at a depth of some 400 to 700 metres below the surface. The project objectives are to provide a basis for comparison and to compare generic options for access routes to the underground deposition areas, to formulate preliminary Design Justification Statements for the continued site-specific engineering of access routes to the underground repository and also to describe and exemplify methodology for optimisation of the repository engineering. In consideration of the requirements of SKB, several alternative access options are explored. The main alternatives are a ramp with one or two operational areas at the surface, a ramp with parallel excavation of a blind shaft and an alternative with shafts only. A suite of objective functions were employed in the evaluation of the main alternatives relating to long-term safety, occupational safety during construction and operation, environmental impact, sustainability of natural resources, total cost, schedules, flexibility and project risks. All alternatives studied are feasible and safe, but the alternative with a spiral ramp and a blind shaft is deemed to be the most favourable option. The alternative has the highest flexibility without any tangible disadvantages related neither to long-term safety, environmental impact nor to schedules. It is an advantage that ramp traffic is drastically reduced as rock and backfilling material is transported by the skip rather than by vehicles in the ramp, thereby reducing risks of accidents and fires in the ramp. The concurrent ramp and shaft excavation also shorten the construction period with 18 months for the underground excavations. The discounted total cost is however 100 million Swedish Kronor higher for this

Flow control of micro-ramps on supersonic forward-facing step flow

International Nuclear Information System (INIS)

Zhang Qing-Hu; Zhu Tao; Wu Anping; Yi Shihe

2016-01-01

The effects of the micro-ramps on supersonic turbulent flow over a forward-facing step (FFS) was experimentally investigated in a supersonic low-noise wind tunnel at Mach number 3 using nano-tracer planar laser scattering (NPLS) and particle image velocimetry (PIV) techniques. High spatiotemporal resolution images and velocity fields of supersonic flow over the testing model were captured. The fine structures and their spatial evolutionary characteristics without and with the micro-ramps were revealed and compared. The large-scale structures generated by the micro-ramps can survive the downstream FFS flowfield. The micro-ramps control on the flow separation and the separation shock unsteadiness was investigated by PIV results. With the micro-ramps, the reduction in the range of the reversal flow zone in streamwise direction is 50% and the turbulence intensity is also reduced. Moreover, the reduction in the average separated region and in separation shock unsteadiness are 47% and 26%, respectively. The results indicate that the micro-ramps are effective in reducing the flow separation and the separation shock unsteadiness. (paper)

Pharmacological characterization of receptor-activity-modifying proteins (RAMPs) and the human calcitonin receptor.

Science.gov (United States)

Armour, S L; Foord, S; Kenakin, T; Chen, W J

1999-12-01

Receptor-activity-modifying proteins (RAMPs) are a family of single transmembrane domain proteins shown to be important for the transport and ligand specificity of the calcitonin gene-related peptide (CGRP) receptor. In this report, we describe the analysis of pharmacological properties of the human calcitonin receptor (hCTR) coexpressed with different RAMPs with the use of the Xenopus laevis melanophore expression system. We show that coexpression of RAMP3 with human calcitonin receptor changed the relative potency of hCTR to human calcitonin (hCAL) and rat amylin. RAMP1 and RAMP2, in contrast, had little effect on the change of hCTR potency to hCAL or rat amylin. When coexpressed with RAMP3, hCTR reversed the relative potency by a 3.5-fold loss in sensitivity to hCAL and a 19-fold increase in sensitivity to rat amylin. AC66, an inverse agonist, produced apparent simple competitive antagonism of hCAL and rat amylin, as indicated by linear Schild regressions. The potency of AC66 was changed in the blockade of rat amylin but not hCAL responses with RAMP3 coexpression. The mean pK(B) for AC66 to hCAL was 9.4 +/- 0.3 without RAMP3 and 9.45 +/- 0.07 with RAMP3. For the antagonism of AC66 to rat amylin, the pK(B) was 9.25 +/- 0.15 without RAMP3 and 8.2 +/- 0.35 with RAMP3. The finding suggests that RAMP3 might modify the active states of calcitonin receptor in such a way as to create a new receptor phenotype that is "amylin-like." Irrespective of the physiological association of the new receptor species, the finding that a coexpressed membrane protein can completely change agonist and antagonist affinities for a receptor raises implications for screening in recombinant receptor systems.

Numerical Study of Quench Protection for Fast-Ramping Accelerator Magnets

OpenAIRE

Schwerg, N; Auchman, B; Mess, K-N; Russenschuck, S

2009-01-01

The quench module of the ROXIE field computation program has been presented at previous conferences. In this paper we discuss recently implemented features that allow quench simulation of fast-ramping superconducting magnets. As the reliability of quench detection during the ramps depends on the signal to noise ratio, we simulate the influence of detection thresholds and the propagation of undetected quenches during the ramps. We also study the effect of an increased copper content and the fe...

Ramp-related incidents involving wheeled mobility device users during transit bus boarding/alighting.

Science.gov (United States)

Frost, Karen L; Bertocci, Gina; Smalley, Craig

2015-05-01

To estimate the prevalence of wheeled mobility device (WhMD) ramp-related incidents while boarding/alighting a public transit bus and to determine whether the frequency of incidents is less when the ramp slope meets the proposed Americans with Disabilities Act (ADA) maximum allowable limit of ≤9.5°. Observational study. Community public transportation. WhMD users (N=414) accessing a public transit bus equipped with an instrumented ramp. Not applicable. Prevalence of boarding/alighting incidents involving WhMD users and associated ramp slopes; factors affecting incidents. A total of 4.6% (n=35) of WhMD users experienced an incident while boarding/alighting a transit bus. Significantly more incidents occurred during boarding (6.3%, n=26) than during alighting (2.2%, n=9) (Pboard/alight when the ramp slope exceeded the proposed ADA maximum allowable ramp slope was 5.1 (95% confidence interval, 2.9-9.0; P9.5° and ramps deployed to street level are associated with a higher frequency of incidents and provision of assistance. Transit agencies should increase awareness among bus operators of the effect kneeling and deployment location (street/sidewalk) have on the ramp slope. In addition, ramp components and the built environment may contribute to incidents. When prescribing WhMDs, skills training must include ascending/descending ramps at slopes encountered during boarding/alighting to ensure safe and independent access to public transit buses. Copyright © 2015 American Congress of Rehabilitation Medicine. Published by Elsevier Inc. All rights reserved.

The impact of product complexity on ramp-up performance

NARCIS (Netherlands)

Pufall, A.A.; Fransoo, J.C.; Jong, de A.; Kok, de A.G.

2012-01-01

Fast product ramp-ups are crucial in consumer electronics because short product lifecycles prevail and profit margins diminish rapidly over time. Yet many companies fail to meet their volume, cost and quality targets and the ramp-up phase remains largely unexplored in new product and supply chain

Evolution of plasma wakes in density up- and down-ramps

Science.gov (United States)

Zhang, C. J.; Joshi, C.; Xu, X. L.; Mori, W. B.; Li, F.; Wan, Y.; Hua, J. F.; Pai, C. H.; Wang, J.; Lu, W.

2018-02-01

The time evolution of plasma wakes in density up- and down-ramps is examined through theory and particle-in-cell simulations. Motivated by observation of the reversal of a linear plasma wake in a plasma density upramp in a recent experiment (Zhang et al 2017 Phys. Rev. Lett. 119 064801) we have examined the behaviour of wakes in plasma ramps that always accompany any plasma source used for plasma-based acceleration. In the up-ramp case it is found that, after the passage of the drive pulse, the wavnumber/wavelength of the wake starts to decrease/increase with time until it eventually tends to zero/infinity, then the wake reverses its propagation direction and the wavenunber/wavelength of the wake begins to increase/shrink. The evolutions of the wavenumber and the phase velocity of the wake as functions of time are shown to be significantly different in the up-ramp and the down-ramp cases. In the latter case the wavenumber of the wake at a particular position in the ramp increases until the wake is eventually damped. It is also shown that the waveform of the wake at a particular time after being excited can be precisely controlled by tuning the initial plasma density profile, which may enable a new type of plasma-based ultrafast optics.

Phase-ramp reduction in interseismic interferograms from pixel-offsets

KAUST Repository

Wang, Teng; Jonsson, Sigurjon

2014-01-01

Interferometric synthetic aperture radar (InSAR) is increasingly used to measure interseismic deformation. Inaccurate satellite-orbit information, expressed as phase ramps across interseismic interferograms, is believed to be one of the main sources of error in such measurements. However, many interferograms exhibit higher phase gradients than expected from the reported orbital accuracy, suggesting that there are other error sources. Here, we show that interferogram phase ramps are in part caused by uncorrected satellite timing-parameter errors. We propose a two-step approach to reduce the phase ramps using pixel-offsets estimated between SAR amplitude images. The first step involves using a digital elevation model (DEM) to estimate absolute timing-parameter errors for the reference image of the SAR dataset and the second step updates the timing parameters of the master image for each interferogram. We demonstrate a clear ramp reduction on interseismic interferograms covering the North Anatolian Fault in eastern Turkey. The resulting interferograms show clear signs of interseismic deformation even before stacking. © 2014 IEEE.

Phase-ramp reduction in interseismic interferograms from pixel-offsets

KAUST Repository

Wang, Teng

2014-05-01

Interferometric synthetic aperture radar (InSAR) is increasingly used to measure interseismic deformation. Inaccurate satellite-orbit information, expressed as phase ramps across interseismic interferograms, is believed to be one of the main sources of error in such measurements. However, many interferograms exhibit higher phase gradients than expected from the reported orbital accuracy, suggesting that there are other error sources. Here, we show that interferogram phase ramps are in part caused by uncorrected satellite timing-parameter errors. We propose a two-step approach to reduce the phase ramps using pixel-offsets estimated between SAR amplitude images. The first step involves using a digital elevation model (DEM) to estimate absolute timing-parameter errors for the reference image of the SAR dataset and the second step updates the timing parameters of the master image for each interferogram. We demonstrate a clear ramp reduction on interseismic interferograms covering the North Anatolian Fault in eastern Turkey. The resulting interferograms show clear signs of interseismic deformation even before stacking. © 2014 IEEE.

IFPE/CNEA-MOX-RAMP, CNEA Power Ramp Irradiations with (PHWR) MOX Fuels

International Nuclear Information System (INIS)

Marino, Armando Carlos; Turnbull, J.A.

2000-01-01

Description: The irradiation of the first MOX nuclear fuel rods fabricated in Argentina began in 1986. These experiences were made in the HFR-Petten reactor, Holland. The six rods were fabricated in the a Facility (GAID-CNEA-Argentina). The first rod has been used for destructive pre-irradiation characterization in the KFK (Kernforschungszentrum Karlsruhe), Germany. The second one was a pathfinder for calibrating HFR systems in Petten. Two other rods included pellets doped with iodine. The first contained mostly CsI whilst the second contained elemental iodine. The concentration of iodine was intended to simulate a burn-up of 15000 MWd/ton(M). The power histories were defined from calculations performed with the BACO code. A 15 day cycle was assumed with a power history that induced PCMI during power cycling. The last high power period was maintained until stress corrosion cracking (SCC) was induced. Two further un-doped rods were used in a sub-program named BU15. Here a burn-up of 15000 MWd/ton(M) was achieved at a low power followed by a final power ramp for one of the rods. The ramp was similar to that used for the Iodine test. The HFR irradiation was conducted satisfactorily. The objective was to attempt a correspondence in behaviour between the doped rods and BU15 rods. PIE detected the presence of micro-cracks inside the cladding of the iodine doped rods. Ramping of the BU15 rod was interrupted when an increase of coolant activity was detected. After discharge, a visual inspection of the rod showed the presence of a small circular hole in the cladding. Additional PIE showed that the hole was due to a SCC failure

Resistors Improve Ramp Linearity

Science.gov (United States)

Kleinberg, L. L.

1982-01-01

Simple modification to bootstrap ramp generator gives more linear output over longer sweep times. New circuit adds just two resistors, one of which is adjustable. Modification cancels nonlinearities due to variations in load on charging capacitor and due to changes in charging current as the voltage across capacitor increases.

Third SCIP modeling workshop. Beneficial impact of slow power ramp on PCI performance

International Nuclear Information System (INIS)

Arimescu, V.I.; Vallejo, I.; Karlsson, J.

2014-01-01

The paper presents the Third SCIP Modeling Workshop (MWS) that was organized to investigate the PCI mitigating effects of lowering the ramp rate. To that end, the Super Ramp-Extension BWR low ramp-rate subprogram of Studsvik's International Super-Ramp (SR) Program, comprising 8 tests, was used together with a set of SCIP single-step and staircase ramps. The modeling exercise was joined by 11 participants using 10 fuel performance codes from industry, research and regulatory organizations. The paper succinctly presents both the areas where reasonable agreement was achieved, as well as the more important differences. Especially, the predicted cladding stresses have been found to differ significantly and some fuel code groupings were identified. Preliminary conclusions are succinctly presented, the highlight being that pure mechanical effects do not seem to fully explain the slow ramps' benefits - the competition between the oxide formation and healing and the SCC-aggressive agent chemical attack could be an important dynamic factor contributing to slow ramp benefits. (author)

Deficiency of RAMP1 attenuates antigen-induced airway hyperresponsiveness in mice.

Directory of Open Access Journals (Sweden)

Manyu Li

Full Text Available Asthma is a chronic inflammatory disease affecting the lung, characterized by breathing difficulty during an attack following exposure to an environmental trigger. Calcitonin gene-related peptide (CGRP is a neuropeptide that may have a pathological role in asthma. The CGRP receptor is comprised of two components, which include the G-protein coupled receptor, calcitonin receptor-like receptor (CLR, and receptor activity-modifying protein 1 (RAMP1. RAMPs, including RAMP1, mediate ligand specificity in addition to aiding in the localization of receptors to the cell surface. Since there has been some controversy regarding the effect of CGRP on asthma, we sought to determine the effect of CGRP signaling ablation in an animal model of asthma. Using gene-targeting techniques, we generated mice deficient for RAMP1 by excising exon 3. After determining that these mice are viable and overtly normal, we sensitized the animals to ovalbumin prior to assessing airway resistance and inflammation after methacholine challenge. We found that mice lacking RAMP1 had reduced airway resistance and inflammation compared to wildtype animals. Additionally, we found that a 50% reduction of CLR, the G-protein receptor component of the CGRP receptor, also ameliorated airway resistance and inflammation in this model of allergic asthma. Interestingly, the loss of CLR from the smooth muscle cells did not alter the airway resistance, indicating that CGRP does not act directly on the smooth muscle cells to drive airway hyperresponsiveness. Together, these data indicate that signaling through RAMP1 and CLR plays a role in mediating asthma pathology. Since RAMP1 and CLR interact to form a receptor for CGRP, our data indicate that aberrant CGRP signaling, perhaps on lung endothelial and inflammatory cells, contributes to asthma pathophysiology. Finally, since RAMP-receptor interfaces are pharmacologically tractable, it may be possible to develop compounds targeting the RAMP1/CLR

Effects of micro-ramps on a shock wave/turbulent boundary layer interaction

NARCIS (Netherlands)

Blinde, P.L.; Humble, R.A.; Van Oudheusden, B.W.; Scarano, F.

2009-01-01

Stereoscopic particle image velocimetry is used to investigate the effects of micro-ramp sub-boundary layer vortex generators, on an incident shock wave/boundary layer interaction at Mach 1.84. Single- and double-row arrangements of micro-ramps are considered. The micro-ramps have a height of 20% of

Functional relevance of G-protein-coupled-receptor-associated proteins, exemplified by receptor-activity-modifying proteins (RAMPs).

Science.gov (United States)

Fischer, J A; Muff, R; Born, W

2002-08-01

The calcitonin (CT) receptor (CTR) and the CTR-like receptor (CRLR) are close relatives within the type II family of G-protein-coupled receptors, demonstrating sequence identity of 50%. Unlike the interaction between CT and CTR, receptors for the related hormones and neuropeptides amylin, CT-gene-related peptide (CGRP) and adrenomedullin (AM) require one of three accessory receptor-activity-modifying proteins (RAMPs) for ligand recognition. An amylin/CGRP receptor is revealed when CTR is co-expressed with RAMP1. When complexed with RAMP3, CTR interacts with amylin alone. CRLR, initially classed as an orphan receptor, is a CGRP receptor when co-expressed with RAMP1. The same receptor is specific for AM in the presence of RAMP2. Together with human RAMP3, CRLR defines an AM receptor, and with mouse RAMP3 it is a low-affinity CGRP/AM receptor. CTR-RAMP1, antagonized preferentially by salmon CT-(8-32) and not by CGRP-(8-37), and CRLR-RAMP1, antagonized by CGRP-(8-37), are two CGRP receptor isotypes. Thus amylin and CGRP interact specifically with heterodimeric complexes between CTR and RAMP1 or RAMP3, and CGRP and AM interact with complexes between CRLR and RAMP1, RAMP2 or RAMP3.

Developing an area-wide system for coordinated ramp meter control.

Science.gov (United States)

2008-12-01

Ramp metering has been broadly accepted and deployed as an effective countermeasure : against both recurrent and non-recurrent congestion on freeways. However, many current ramp : metering algorithms tend to improve only freeway travels using local d...

First beam test of a combined ramp and squeeze at LHC

CERN Document Server

Wenninger, Jorg; Coello De Portugal - Martinez Vazquez, Jaime Maria; Gorzawski, Arkadiusz; Redaelli, Stefano; Schaumann, Michaela; Solfaroli Camillocci, Matteo; CERN. Geneva. ATS Department

2015-01-01

With increasing maturity of LHC operation it is possible to envisage more complex beam manipulations. At the same time operational efficiency receives increasing attention. So far ramping the beams to their target energy and squeezing the beams to smaller or higher beta are decoupled at the LHC. (De-)squeezing is always performed at the target energy, currently 6.5 TeV. Studies to combine the ramp and squeeze processes have been made for the LHC since 2011, but so far no experimental test with beam had ever performed. This note describes the first machine experiment with beam aiming at validating the combination of ramp and squeeze, the so-called combined ramp and squeeze (CRS).

Design for Fermilab main injector magnet ramps which account for hysteresis

International Nuclear Information System (INIS)

Brown, B.C.; Bhat, C.M.; Harding, D.J.; Martin, P.S.; Wu, G.

1997-05-01

Although the dominant fields in accelerator electromagnets are proportional to the excitation current, precise control of accelerator parameters requires a detailed understanding of the fields in Main Injector magnets including contribution from eddy currents, magnet saturation, and hysteresis. Operation for decelerating beam makes such considerations particularly significant. Analysis of magnet measurements and design of control system software is presented. Field saturation and its effects on low field hysteresis are accounted for in specifying the field ramps for dipole, quadrupole and sextupole magnets. Some simplifying assumptions are made which are accepted as limitations on the required ramp sequences. Specifications are provided for relating desired field ramps to required current ramps for the momentum, tune, and chromaticity control

Power ramp tests of BWR-MOX fuels

International Nuclear Information System (INIS)

Asahi, K.; Oguma, M.; Higuchi, S.; Kamimua, K.; Shirai, Y.; Bodart, S.; Mertens, L.

1996-01-01

Power ramp test of BWR-MOX and UO 2 fuel rods base irradiated up to about 60 GWd/t in Dodewaard reactor have been conducted in BR2 reactor in the framework of the international DOMO programme. The MOX pellets were provided by BN (MIMAS process) and PNC (MH method). The MOX fuel rods with Zr-liner and non-liner cladding and the UO 2 fuel rods with Zr-liner cladding remained intact during the stepwise power ramp tests to about 600 W/cm, even at about 60 GWd/t

Solar ramping distributions over multiple timescales and weather patterns

Energy Technology Data Exchange (ETDEWEB)

Hodge, Bri-Mathias; Hummon, Marissa; Orwig, Kirsten [National Renewable Energy Laboratory, Golden, CO (United States)

2011-07-01

As greater amounts of solar power are included in the power system it is becoming increasingly important to have a better characterization of the variability of solar power over the timescales that are relevant to power system operations. In this paper, we examine the distribution of ramp events that occur in global horizontal irradiance measurements from a number of sites in the western United States. The distributions are found to be significantly non-normal over multiple timescales from 1 minute to 1 hour. A hyberbolic distribution is suggested for more accurately representing the observed ramp distributions. Additionally, the ramp distributions that occur during different classifications of weather patterns are characterized and significant differences are observed between patterns. (orig.)

Analysis of mechanical and chemical pellet-clad interaction during power ramps

International Nuclear Information System (INIS)

Vogl, W.; Hering, W.; Peehs; Lavake, J.

1979-01-01

A research and development program is being conducted by KWU and C-E to investigate Pellet/Clad Interaction (PCI) in LWR fuel rods during power ramping. Out-of-pile iodine stress corrosion cracking studies, in-pile ramp experiments and hot cell chemical and metallographical post-irradiation examinations are being performed to study and evaluate both the power limitations and the basic mechanisms of PCI as well as practical methods to improve ramping performance. (orig.)

Effects of Linear Falling Ramp Reset Pulse on Addressing Operation in AC PDP

International Nuclear Information System (INIS)

Liu Zujun; Liang Zhihu; Liu Chunliang; Meng Lingguo

2006-01-01

The effects of linear falling ramp reset pulse related to addressing operation in an alternating current plasma display panel (AC PDP) were studied. The wall charge waveforms were measured by the electrode balance method in a 12-inch coplanar AC PDP. The wall charge waveforms show the relationship between the slope ratio of the falling ramp reset pulse and the wall charges at the end of the falling ramp reset pulse which influences the addressing stability. Then the effects of the slope ratio of the linear falling ramp reset pulse on the addressing voltage and addressing time were investigated. The experimental results show that the minimum addressing voltage increases with the increase of the slope ratio of the falling ramp reset pulse, and so does the minimum addressing time. Based on the experimental results, the optimization of the addressing time and the slope ratio of the falling ramp pulse is discussed

A survey on wind power ramp forecasting.

Energy Technology Data Exchange (ETDEWEB)

Ferreira, C.; Gama, J.; Matias, L.; Botterud, A.; Wang, J. (Decision and Information Sciences); (INESC Porto)

2011-02-23

The increasing use of wind power as a source of electricity poses new challenges with regard to both power production and load balance in the electricity grid. This new source of energy is volatile and highly variable. The only way to integrate such power into the grid is to develop reliable and accurate wind power forecasting systems. Electricity generated from wind power can be highly variable at several different timescales: sub-hourly, hourly, daily, and seasonally. Wind energy, like other electricity sources, must be scheduled. Although wind power forecasting methods are used, the ability to predict wind plant output remains relatively low for short-term operation. Because instantaneous electrical generation and consumption must remain in balance to maintain grid stability, wind power's variability can present substantial challenges when large amounts of wind power are incorporated into a grid system. A critical issue is ramp events, which are sudden and large changes (increases or decreases) in wind power. This report presents an overview of current ramp definitions and state-of-the-art approaches in ramp event forecasting.

Optimized Swinging Door Algorithm for Wind Power Ramp Event Detection: Preprint

Energy Technology Data Exchange (ETDEWEB)

Cui, Mingjian; Zhang, Jie; Florita, Anthony R.; Hodge, Bri-Mathias; Ke, Deping; Sun, Yuanzhang

2015-08-06

Significant wind power ramp events (WPREs) are those that influence the integration of wind power, and they are a concern to the continued reliable operation of the power grid. As wind power penetration has increased in recent years, so has the importance of wind power ramps. In this paper, an optimized swinging door algorithm (SDA) is developed to improve ramp detection performance. Wind power time series data are segmented by the original SDA, and then all significant ramps are detected and merged through a dynamic programming algorithm. An application of the optimized SDA is provided to ascertain the optimal parameter of the original SDA. Measured wind power data from the Electric Reliability Council of Texas (ERCOT) are used to evaluate the proposed optimized SDA.

Power ramp testing method for PWR fuel rod at research reactor

International Nuclear Information System (INIS)

Zhou Yidong; Zhang Peisheng; Zhang Aimin; Gao Yongguang; Wang Huarong

2003-01-01

A tentative power ramp test for short PWR fuel rod has been conducted at the Heavy Water Research Reactor (HWRR) in China Institute of Atomic Energy (CIAE). The test fuel rod was cooled by the circulating water in the test loop. The power ramp was realized by moving solid neutron-absorbing screen around the fuel rod. The linear power of the fuel rod increased from 220 W/cm to 340 W/cm with a power ramp rate of 20 W/cm/min. The power of the fuel rod was monitored by both in-core thermal and nuclear measurement sensors in the test rig. This test provides experiences for further developing the power ramp test methods for PWR fuel rods at research reactor. (author)

Numerical Study of Quench Protection for Fast-Ramping Accelerator Magnets

CERN Document Server

Schwerg, N; Mess, K-N; Russenschuck, S

2009-01-01

The quench module of the ROXIE field computation program has been presented at previous conferences. In this paper we discuss recently implemented features that allow quench simulation of fast-ramping superconducting magnets. As the reliability of quench detection during the ramps depends on the signal to noise ratio, we simulate the influence of detection thresholds and the propagation of undetected quenches during the ramps. We also study the effect of an increased copper content and the feasibility of a self-protected magnet surviving a powering cycle with an undetected quench and without quench heater firing or energy-extraction system.

Modelling of pellet-clad interaction during power ramps

International Nuclear Information System (INIS)

Zhou, G.; Lindback, J.E.; Schutte, H.C.; Jernkvist, L.O.; Massih, A.R.; Massih, A.R.

2005-01-01

A computational method to describe the pellet-clad interaction phenomenon is presented. The method accounts for the mechanical contact between fragmented pellets and the zircaloy clad, as well as for chemical reaction of fission products with zircaloy during power ramps. Possible pellet-clad contact states, soft, hard and friction, are taken into account in the computational algorithm. The clad is treated as an elastic-plastic-viscoplastic material with irradiation hardening. Iodine-induced stress corrosion cracking is described by using a fracture mechanics-based model for crack propagation. This integrated approach is used to evaluate two power ramp experiments made on boiling water reactor fuel rods in test reactors. The influence of the pellet-clad coefficient of friction on clad deformation is evaluated and discussed. Also, clad deformations, pellet-clad gap size and fission product gas release for one of the ramped rods are calculated and compared with measured data. (authors)

Ramp discharge in Z-pinch

Energy Technology Data Exchange (ETDEWEB)

Gaber, W.H.; Beshara, A.B.; El-Bialy, A.B.; Masoud, M.M. [Plasma and Nuclear Fusion Dept., N.R.C., Atomic Energy Authority, Enshass (Egypt)

2004-07-01

A ramp Z-pinch discharge is designed and built in order to increase the pinch ratio and obtain a maximum contraction, and to increase the temperature. The discharge chamber is a cylindrical Pyrex tube of 25 cm long, 18.5 cm, 20 cm inner and outer diameter and two circular Aluminum plates of radius 15 cm separated by 21 cm are inserted into the tube. The tube is filled with He gas at 0.1 mbar. Two capacitor banks are used, the first bank 30 {mu}F and the second fast bank 1.3 {mu}F. The charging voltage was 8 kV for both banks. The discharge current and voltage of each bank are measured by potential divider and Rogowski coil respectively. Also the plasma inductance and resistance are obtained for each case. The plasma inductance has its peak value 300 nH at 4 {mu}s, while the plasma resistance has it minimum 8 m{omega} at the same time in the case of conventional discharge (single bank). In the case of ramp discharge, the inductance has two peaks 440 nH, 380 nH at 4 {mu}s, 9.5 {mu}s respectively, while the resistance has two minimum 4 m{omega}, 20 m{omega} at at 4 {mu}s, 9.5 {mu}s respectively. The temperature has been measure spectroscopically by using relative continuum intensity ratio method. The temperature has its peak value 38 eV at 4 {mu}s for single bank case, while it larger peak value 55 eV for ramp case. (orig.)

Ion-beam etching of ramps in thin film heterostructures

International Nuclear Information System (INIS)

Mozhaev, P. B.; Mozhaeva, Ju. E.; Komissinskii, P. V.

2002-01-01

Ion-beam patterning of thin films and heterostructures is one of the most common processes of fabrication of thin film devices and structures. 'Directed' nature of ion-beam etching provides a possibility to form certain profiles on the films surface, like shallow ramps, when etching is performed at some inclination angle. A simple geometrical model is presented, describing the formation of a ramp as a shadow of the mask on the film surface. Good agreement with the experiment can be obtained if the mask etching is taken into account. The etching at the opposite direction ('high-angle etching') also can be satisfactory described by the model. The profile of the slope - positive or negative curvature, pits near the end of the ramp - is discussed as a function of the etch rate dependence on the incidence angle. Such etch rate dependences for some often used materials were measured. An area of instability of the resulting ramp shape is found for the 'high-angle etching'. The model is compared with the experimental data reported by other groups. Finally ion-beam etching of a rotating sample at non-normal incidence is discussed, the results are compared with experimental data. (Authors)

A real-time crash prediction model for the ramp vicinities of urban expressways

Directory of Open Access Journals (Sweden)

Moinul Hossain

2013-07-01

Full Text Available Ramp vicinities are arguably the known black-spots on urban expressways. There, while maintaining high speed, drivers need to respond to several complex events such as maneuvering, reading road signs, route planning and maintaining safe distance from other maneuvering vehicles simultaneously which demand higher level of cognitive response to ensure safety. Therefore, any additional discomfort caused by traffic dynamics may induce driving error resulting in a crash. This manuscript presents a methodology for identifying these dynamically forming hazardous traffic conditions near the ramp vicinities with high resolution real-time traffic flow data. It separates the ramp vicinities into four zones – upstream and downstream of entrance and exit ramps, and builds four separate real-time crash prediction models. Around two year (December 2007 to October 2009 crash data as well as their matching traffic sensor data from Shibuya 3 and Shinjuku 4 expressways under the jurisdiction of Tokyo Metropolitan Expressway Company Limited have been utilized for this research. Random multinomial logit, a forest of multinomial logit models, has been used to identify the most important variables. Finally, a real-time modeling method, Bayesian belief net (BBN, has been employed to build the four models using ramp flow, flow and congestion index in the upstream and flow and speed in the downstream of the ramp location as variables. The newly proposed models could predict 50%, 42%, 43% and 55% of the future crashes with around 10% false alarm for the downstream of entrance, downstream of exit, upstream of entrance and upstream of exit ramps respectively. The models can be utilized in combination with various traffic smoothing measures such as ramp metering, variable speed limit, warning messages through variable message signs, etc. to enhance safety near the ramp vicinities.

Ramp injector scale effects on supersonic combustion

Science.gov (United States)

Trebs, Adam

The combustion field downstream of a 10 degree compression ramp injector has been studied experimentally using wall static pressure measurement, OH-PLIF, and 2 kHz intensified video filtered for OH emission at 320 nm. Nominal test section entrance conditions were Mach 2, 131 kPa static pressure, and 756K stagnation temperature. The experiment was equipped with a variable length inlet duct that facilitated varying the boundary layer development length while the injector shock structure in relation to the combustor geometry remained nearly fixed. As the boundary within an engine varies with flight condition and does not scale linearly with the physical scale of the engine, the boundary layer scale relative to mixing structures of the engine becomes relevant to the problem of engine scaling and general engine performance. By varying the boundary layer thickness from 40% of the ramp height to 150% of the ramp height, changes in the combustion flowfield downstream of the injector could be diagnosed. It was found that flame shape changed, the persistence of the vortex cores was reduced, and combustion efficiency rose as the incident boundary layer grew.

Modeling ramp compression experiments using large-scale molecular dynamics simulation.

Energy Technology Data Exchange (ETDEWEB)

Mattsson, Thomas Kjell Rene; Desjarlais, Michael Paul; Grest, Gary Stephen; Templeton, Jeremy Alan; Thompson, Aidan Patrick; Jones, Reese E.; Zimmerman, Jonathan A.; Baskes, Michael I. (University of California, San Diego); Winey, J. Michael (Washington State University); Gupta, Yogendra Mohan (Washington State University); Lane, J. Matthew D.; Ditmire, Todd (University of Texas at Austin); Quevedo, Hernan J. (University of Texas at Austin)

2011-10-01

Molecular dynamics simulation (MD) is an invaluable tool for studying problems sensitive to atomscale physics such as structural transitions, discontinuous interfaces, non-equilibrium dynamics, and elastic-plastic deformation. In order to apply this method to modeling of ramp-compression experiments, several challenges must be overcome: accuracy of interatomic potentials, length- and time-scales, and extraction of continuum quantities. We have completed a 3 year LDRD project with the goal of developing molecular dynamics simulation capabilities for modeling the response of materials to ramp compression. The techniques we have developed fall in to three categories (i) molecular dynamics methods (ii) interatomic potentials (iii) calculation of continuum variables. Highlights include the development of an accurate interatomic potential describing shock-melting of Beryllium, a scaling technique for modeling slow ramp compression experiments using fast ramp MD simulations, and a technique for extracting plastic strain from MD simulations. All of these methods have been implemented in Sandia's LAMMPS MD code, ensuring their widespread availability to dynamic materials research at Sandia and elsewhere.

New Product Fumbles - Organizing for the Ramp-up Process

DEFF Research Database (Denmark)

Christensen, Irene

This study examines rapid prototyping, also referred to as new production launch, or ramp-up time. A strong emphasis on speed is vital for the success of a product development and market launch. Managers concern themselves with organizing ramp-up activities into arrayed sequences to achieve...... production launch goals. These sequences are not only regarding prearranged linear milestones, but extensively reviewed and often reorganized complex activities, with the managerial goal of a wellconfigured productive process. The need to manage the final phase in product development is evident, because many...... of the development of products. This has been achieved by longitudinally studying a total of eight major development cases at a large Scandinavian manufacturing company over a period of three years. These development projects faced different challenges during the interface between R&D and ramp-up production...

Study on wake structure characteristics of a slotted micro-ramp with large-eddy simulation

Energy Technology Data Exchange (ETDEWEB)

Dong, Xiangrui; Chen, Yaohui; Dong, Gang; Liu, Yixin, E-mail: cyh873@163.com [National Key Laboratory of Transient Physics, Nanjing University of Science and Technology, Nanjing, 210094 (China)

2017-06-15

In this paper, a novel slotted ramp-type micro vortex generator (slotted micro-ramp) for flow separation control is simulated in the supersonic flow of Ma = 1.5, based on large eddy simulation combined with the finite volume method. The wake structure characteristics and control mechanisms of both slotted and standard micro-ramps are presented and discussed. The results show that the wake of standard micro-ramp includes a primary counter-rotating streamwise vortex pair, a train of vortex rings, and secondary vortices. The slotted micro-ramp has more complicated wake structures, which contain a confluent counter-rotating streamwise vortex pair and additional streamwise vortices, with the same rotation generated by slot and the vortex rings enveloping the vortex pair. The additional vortices generated by the slot of the micro-ramp can mix with the primary counter-rotating vortex pair, extend the life time, and strengthen the vortex intensity of primary vortex pair. Moreover, the slot can effectively alleviate, or even eliminate the backflow and decrease the profile drag induced by the standard micro-ramp, therefore improving the efficiency of separation control. (paper)

Experimental Study of Boundary Layer Flow Control Using an Array of Ramp-Shaped Vortex Generators

Science.gov (United States)

Hirt, Stefanie M.; Zaman, Khairul B.M.Q.; Bencic, Tomothy J.

2012-01-01

The objective of this study was to obtain a database on the flowfield past an array of vortex generators (VGs) in a turbulent boundary layer. All testing was carried out in a low speed wind tunnel with a flow velocity of 29 ft/sec, giving a Reynolds number of 17,500 based on the width of the VG. The flowfield generated by an array of five ramp-shaped vortex generators was examined with hot wire anemometry and smoke flow visualization. The magnitude and extent of the velocity increase near the wall, the penetration of the velocity deficit into the core flow, and the peak streamwise vorticity are examined. Influence of various parameters on the effectiveness of the array is considered on the basis of the ability to pull high momentum fluid into the near wall region.

Extrapolating power-ramp performance criteria for current and advanced CANDU fuels

Energy Technology Data Exchange (ETDEWEB)

Tayal, M.; Chassie, G.G

2000-06-01

To improve the precision and accuracy of power-ramp performance criteria for high-burnup fuel, we have examined in-reactor fuel performance data as well as out-reactor test data. The data are consistent with some of the concepts used in the current formulations for defining fuel failure thresholds, such as size of power-ramp and extent of burnup. Our review indicates that there is a need to modify some other aspects of the current formulations; therefore, a modified formulation is presented in this paper. The improvements mainly concern corrodent concentration and its relationships with threshold stress for failure. The new formulation is consistent with known and expected trends such as strength of Zircaloy in corrosive environment, timing of the release of fission products to the pellet-to-sheath gap, CANLUB coating, and fuel burnup. Because of the increased precision and accuracy, the new formulation is better able to identify operational regimes that are at risk of power-ramp failures; this predictive ability provides enhanced protection to fuel against power-ramp defects. At die same time, by removing unnecessary conservatisms in other areas, the new formulation permits a greater range of defect-free operational envelope as well as larger operating margins in regions that are, in fact, not prone to power-ramp failures. (author)

Power ramp tests of high burnup BWR segment rods

International Nuclear Information System (INIS)

Hayashi, H.; Etoh, Y.; Tsukuda, Y.; Shimada, S.; Sakurai, H.

2002-01-01

Lead use assemblies (LUAs) of high burnup 8x8 fuel design for Japanese BWRs were irradiated up to 5 cycles in Fukushima Daini Nuclear Power Station No. 2 Unit. Segment rods were installed in LUAs and used for power ramp tests in Japanese Material Test Reactor (JMTR). Post irradiation examinations (PIEs) of segment rods were carried out at Nippon Nuclear Fuel Development Co., Ltd. before and after ramp tests. Maximum linear heat rates of LUAs were kept above 300 W/cm in the first cycle, above 250 W/cm in the second and third cycles and decreased to 200 W/cm in the fourth cycle and 80 W/cm in the fifth cycle. The integrity of high burnup 8x8 fuel was confirmed up to the bundle burnup of 48 GWd/t after 5 cycles of irradiation. Systematic and high quality data were collected through detailed PIEs. The main results are as follows. The oxide on the outer surface of cladding tubes was uniform and its thickness was less than 20 micro-meter after 5 cycles of irradiation and was almost independent of burnup. Hydrogen contents in cladding tubes were less than 150 ppm after 5 cycles of irradiation, although hydrogen contents increased during the fourth and fifth irradiation cycles. Mechanical properties of cladding tubes were on the extrapolated line of previous data up to 5 cycles of irradiation. Fission gas release rates were in the low level (mainly less than 6%) up to 5 cycles of irradiation due to the design to decrease pellet temperature. Pellet-cladding bonding layers were observed after the third cycle and almost full bonding was observed after the fifth cycle. Pellet volume increased with burnup in proportion to solid swelling rate up to the forth cycle. After the fifth cycle, slightly higher pellet swelling was confirmed. Power ramp tests were carried out and satisfactory performance of Zr-lined cladding tube was confirmed up to 60 GWd/t (segment average burnup). One segment rod irradiated for 3 cycles failed by a single step ramp test at terminal ramp power of 614 W

Ramp Technology and Intelligent Processing in Small Manufacturing

Science.gov (United States)

Rentz, Richard E.

1992-01-01

To address the issues of excessive inventories and increasing procurement lead times, the Navy is actively pursuing flexible computer integrated manufacturing (FCIM) technologies, integrated by communication networks to respond rapidly to its requirements for parts. The Rapid Acquisition of Manufactured Parts (RAMP) program, initiated in 1986, is an integral part of this effort. The RAMP program's goal is to reduce the current average production lead times experienced by the Navy's inventory control points by a factor of 90 percent. The manufacturing engineering component of the RAMP architecture utilizes an intelligent processing technology built around a knowledge-based shell provided by ICAD, Inc. Rules and data bases in the software simulate an expert manufacturing planner's knowledge of shop processes and equipment. This expert system can use Product Data Exchange using STEP (PDES) data to determine what features the required part has, what material is required to manufacture it, what machines and tools are needed, and how the part should be held (fixtured) for machining, among other factors. The program's rule base then indicates, for example, how to make each feature, in what order to make it, and to which machines on the shop floor the part should be routed for processing. This information becomes part of the shop work order. The process planning function under RAMP greatly reduces the time and effort required to complete a process plan. Since the PDES file that drives the intelligent processing is 100 percent complete and accurate to start with, the potential for costly errors is greatly diminished.

Vehicle operation characteristic under different ramp entrance conditions in underground road: Analysis, simulation and modelling

Science.gov (United States)

Yao, Qiming; Liu, Shuo; Liu, Yang

2018-05-01

An experimental design was used to study the vehicle operation characteristics of different ramp entrance conditions in underground road. With driving simulator, the experimental scenarios include left or right ramp with first, second and third service level, respectively, to collect vehicle speed, acceleration, lateral displacement and location information at the ramp entrance section. By using paired t-test and ANOVA, the influence factors of vehicle operating characteristics are studied. The result shows that effects of ramp layout and mainline traffic environment on vehicle operation characteristics are significant. The regression model of vehicle traveling distance on acceleration lane is established. Suggestions are made for ramp entrance design of underground road.

Rural Alaska Mentoring Project (RAMP)

Science.gov (United States)

Cash, Terry

2011-01-01

For over two years the National Dropout Prevention Center (NDPC) at Clemson University has been supporting the Lower Kuskokwim School District (LKSD) in NW Alaska with their efforts to reduce high school dropout in 23 remote Yup'ik Eskimo villages. The Rural Alaska Mentoring Project (RAMP) provides school-based E-mentoring services to 164…

The Nucleation and Propagation of Thrust Ramps: Insights from Quantitative Analysis of Frictional Analog (Sandbox) Models

Science.gov (United States)

Sen, P.; Haq, S. S.; Marshak, S.

2012-12-01

Particle Imaging Velocimetry (PIV) provides a unique opportunity to analyze deformation in sandbox analog models at a scale that allows documentation of movement within and around individual shear structures. We employed PIV analysis to quantify deformation in sandbox experiments designed to simulate the initiation of thrust ramps developed during crustal shortening (i.e., contractional deformation). Our intent was to answer a long-standing question: Do ramps initiate at the tip of a detachment, or do they initiate in the interior of a deforming layer and propagate up-dip and down-dip until they link to the detachment at a location to the hinterland of the detachment's tip line? Most geometric studies of ramp-flat geometries in fold-thrust belts assume that ramps propagate up-dip from the tip of the detachment, and grow only in one direction. Field studies, in contrast, reveal that layer-parallel shortening structures develop to the foreland of the last ramp to form, suggesting that ramps initiate in a thrust sheet that has already undergone displacement above a detachment. Published sandbox models, using color-sand marker layers, support this idea. To test this idea further, we set up a model using a 3 m-long by 0.31-m wide glass-walled sandbox with a rigid backstop. The sand layer was sifted onto a sheet of mylar that could be pulled beneath the rigid backstop. Sand used in our experiments consisted of <250 μm-diameter grains. We carried out multiple runs using 4 cm, 5 cm and 6 cm-thick layers. Images were acquired over 1 mm displacement intervals using an 18 mega-pixel camera. By moving the camera at specific steps during the experiment, we sampled the development of several thrust ramps. The images taken during experimental runs were analyzed with a MATLAB-based program called 'PIV LAB' that utilizes an image cross-correlation subroutine to determine displacement fields of the sand particles. Our results demonstrate that: (1) thrust ramps initiate within the

Effect of PWR Re-start ramp rate on pellet-cladding interactions

International Nuclear Information System (INIS)

Yagnik, S.K.; Chang, B.C.; Sunderland, D.J.

2005-01-01

To mitigate pellet-cladding interaction (PCI) leading to fuel rod failures, fuel suppliers specify reactor power ramp rate limitations during reactor start-up after an outage. Typical re-start ramp rates are restricted and range between 3-4% per hour of full reactor power above a threshold power level. Relaxation of threshold power and ramp rate restrictions has the potential to improve plant economics. The paper will compare known re-start power ascension procedures employed in the US, German, French and Korean PWRs after a refuelling outage. A technical basis for optimising power ascension procedures during reactor start-up can be developed using analytical modelling. The main objective of the modelling is to determine the potential for PCI failure for various combinations of threshold power levels and ramp rate levels. A key element of our analysis is to estimate the decrease in margin to cladding failure by ISCC based on a time-temperature-stress failure criterion fashioned Act a cumulative cladding damage index. The analysis approach and the cladding damage model will be described and the results from three case studies based on the FALCON fuel rod behaviour code will be reported. We conclude that the PCI behaviour is more affected by ramp rate and threshold power than by the fuel design and that the fuel power history is the most important parameter. (authors)

Modelling ramp-up curves to reflect learning: improving capacity planning in secondary pharmaceutical production

DEFF Research Database (Denmark)

Hansen, Klaus Reinholdt Nyhuus; Grunow, Martin

2015-01-01

availability at market launch is ensured. Our MILP model is applied to a real industry case study using three empirically observed ramp-up curves to demonstrate its value as decision support tool. We demonstrate the superiority of our volume-dependent method over the traditional time-dependent ramp......The experience gained during production ramp-up leads to an increase of the effective production capacity over time. However, full utilisation of production capacity is not always possible during ramp-up. In such cases, the experience gained and hence the available effective capacity...... are overestimated. We develop a new method, which captures ramp-up as a function of the cumulative production volume to better reflect the experience gained while producing the new product. The use of the more accurate and computationally effective approach is demonstrated for the case of secondary pharmaceutical...

Vortex Generators to Control Boundary Layer Interactions

Science.gov (United States)

Babinsky, Holger (Inventor); Loth, Eric (Inventor); Lee, Sang (Inventor)

2014-01-01

Devices for generating streamwise vorticity in a boundary includes various forms of vortex generators. One form of a split-ramp vortex generator includes a first ramp element and a second ramp element with front ends and back ends, ramp surfaces extending between the front ends and the back ends, and vertical surfaces extending between the front ends and the back ends adjacent the ramp surfaces. A flow channel is between the first ramp element and the second ramp element. The back ends of the ramp elements have a height greater than a height of the front ends, and the front ends of the ramp elements have a width greater than a width of the back ends.

Relationship between work rate and oxygen uptake in mitochondrial myopathy during ramp-incremental exercise

Directory of Open Access Journals (Sweden)

A.C. Gimenes

2011-04-01

Full Text Available We determined the response characteristics and functional correlates of the dynamic relationship between the rate (Δ of oxygen consumption ( O2 and the applied power output (work rate = WR during ramp-incremental exercise in patients with mitochondrial myopathy (MM. Fourteen patients (7 males, age 35.4 ± 10.8 years with biopsy-proven MM and 10 sedentary controls (6 males, age 29.0 ± 7.8 years took a ramp-incremental cycle ergometer test for the determination of the O2 on-exercise mean response time (MRT and the gas exchange threshold (GET. The ΔO2/ΔWR slope was calculated up to GET (S1, above GET (S2 and over the entire linear portion of the response (S T. Knee muscle endurance was measured by isokinetic dynamometry. As expected, peak O2 and muscle performance were lower in patients than controls (P O2/ΔWR than controls, especially the S2 component (6.8 ± 1.5 vs 10.3 ± 0.6 mL·min-1·W-1, respectively; P O2/ΔWR (S T and muscle endurance, MRT-O2, GET and peak O2 in MM patients (P O2/ΔWR below 8 mL·min-1·W-1 had severely reduced peak O2 values (O2 had lower ΔO2/ΔWR (P O2/ΔWR is typically reduced in patients with MM, being related to increased functional impairment and higher cardiopulmonary stress.

Coordinated Ramping of Dorsal Striatal Pathways preceding Food Approach and Consumption.

Science.gov (United States)

London, Tanisha D; Licholai, Julia A; Szczot, Ilona; Ali, Mohamed A; LeBlanc, Kimberly H; Fobbs, Wambura C; Kravitz, Alexxai V

2018-04-04

The striatum controls food-related actions and consumption and is linked to feeding disorders, including obesity and anorexia nervosa. Two populations of neurons project from the striatum: direct pathway medium spiny neurons and indirect pathway medium spiny neurons. The selective contribution of direct pathway medium spiny neurons and indirect pathway medium spiny neurons to food-related actions and consumption remains unknown. Here, we used in vivo electrophysiology and fiber photometry in mice (of both sexes) to record both spiking activity and pathway-specific calcium activity of dorsal striatal neurons during approach to and consumption of food pellets. While electrophysiology revealed complex task-related dynamics across neurons, population calcium was enhanced during approach and inhibited during consumption in both pathways. We also observed ramping changes in activity that preceded both pellet-directed actions and spontaneous movements. These signals were heterogeneous in the spiking units, with neurons exhibiting either increasing or decreasing ramps. In contrast, the population calcium signals were homogeneous, with both pathways having increasing ramps of activity for several seconds before actions were initiated. An analysis comparing population firing rates to population calcium signals also revealed stronger ramping dynamics in the calcium signals than in the spiking data. In a second experiment, we trained the mice to perform an action sequence to evaluate when the ramping signals terminated. We found that the ramping signals terminated at the beginning of the action sequence, suggesting they may reflect upcoming actions and not preconsumption activity. Plasticity of such mechanisms may underlie disorders that alter action selection, such as drug addiction or obesity. SIGNIFICANCE STATEMENT Alterations in striatal function have been linked to pathological consumption in disorders, such as obesity and drug addiction. We recorded spiking and

Solar Power Ramp Events Detection Using an Optimized Swinging Door Algorithm: Preprint

Energy Technology Data Exchange (ETDEWEB)

Cui, Mingjian; Zhang, Jie; Florita, Anthony; Hodge, Bri-Mathias; Ke, Deping; Sun, Yuanzhang

2015-08-07

Solar power ramp events (SPREs) are those that significantly influence the integration of solar power on non-clear days and threaten the reliable and economic operation of power systems. Accurately extracting solar power ramps becomes more important with increasing levels of solar power penetrations in power systems. In this paper, we develop an optimized swinging door algorithm (OpSDA) to detection. First, the swinging door algorithm (SDA) is utilized to segregate measured solar power generation into consecutive segments in a piecewise linear fashion. Then we use a dynamic programming approach to combine adjacent segments into significant ramps when the decision thresholds are met. In addition, the expected SPREs occurring in clear-sky solar power conditions are removed. Measured solar power data from Tucson Electric Power is used to assess the performance of the proposed methodology. OpSDA is compared to two other ramp detection methods: the SDA and the L1-Ramp Detect with Sliding Window (L1-SW) method. The statistical results show the validity and effectiveness of the proposed method. OpSDA can significantly improve the performance of the SDA, and it can perform as well as or better than L1-SW with substantially less computation time.

A Density-Based Ramp Metering Model Considering Multilane Context in Urban Expressways

Directory of Open Access Journals (Sweden)

Li Tang

2017-01-01

Full Text Available As one of the most effective intelligent transportation strategies, ramp metering is regularly discussed and applied all over the world. The classic ramp metering algorithm ALINEA dominates in practical applications due to its advantages in stabilizing traffic flow at a high throughput level. Although ALINEA chooses the traffic occupancy as the optimization parameter, the classic traffic flow variables (density, traffic volume, and travel speed may be easier obtained and understood by operators in practice. This paper presents a density-based ramp metering model for multilane context (MDB-RM on urban expressways. The field data of traffic flow parameters is collected in Chengdu, China. A dynamic density model for multilane condition is developed. An error function represented by multilane dynamic density is introduced to adjust the different usage between lanes. By minimizing the error function, the density of mainstream traffic can stabilize at the set value, while realizing the maximum decrease of on-ramp queues. Also, VISSIM Component Object Model of Application Programming Interface is used for comparison of the MDB-RM model with a noncontrol, ALINEA, and density-based model, respectively. The simulation results indicate that the MDB-RM model is capable of achieving a comprehensive optimal result from both sides of the mainstream and on-ramp.

Optimizing the current ramp-up phase for the hybrid ITER scenario

International Nuclear Information System (INIS)

Hogeweij, G.M.D.; Citrin, J.; Artaud, J.-F.; Imbeaux, F.; Litaudon, X.; Casper, T.A.; Köchl, F.; Voitsekhovitch, I.

2013-01-01

The current ramp-up phase for the ITER hybrid scenario is analysed with the CRONOS integrated modelling suite. The simulations presented in this paper show that the heating systems available at ITER allow, within the operational limits, the attainment of a hybrid q profile at the end of the current ramp-up. A reference ramp-up scenario is reached by a combination of NBI, ECCD (UPL) and LHCD. A heating scheme with only NBI and ECCD can also reach the target q profile; however, LHCD can play a crucial role in reducing the flux consumption during the ramp-up phase. The optimum heating scheme depends on the chosen transport model, and on assumptions of parameters like n e peaking, edge T e,i and Z eff . The sensitivity of the current diffusion on parameters that are not easily controlled, shows that development of real-time control is important to reach the target q profile. A first step in that direction has been indicated in this paper. Minimizing resistive flux consumption and optimizing the q profile turn out to be conflicting requirements. A trade-off between these two requirements has to be made. In this paper it is shown that fast current ramp with L-mode current overshoot is at the one extreme, i.e. the optimum q profile at the cost of increased resistive flux consumption, whereas early H-mode transition is at the other extreme. (paper)

Effects of ramp reset pulses on the address discharge in a shadow mask plasma display panel

International Nuclear Information System (INIS)

Yang Lanlan; Tu Yan; Zhang Xiong; Jiang Youyan; Zhang Jian; Wang Baoping

2007-01-01

A two-dimensional self-consistent numerical simulation model is used to analyse the effects of the ramp reset pulses on the address discharge in a shadow mask plasma display panel (SM-PDP). Some basic parameters such as the slope of the ramp pulse and the terminal voltage of the ramp reset period are varied to investigate their effects. The simulation results illustrate that the wall voltage is mainly decided by the terminal voltage and the firing voltage at the end of the ramp reset period. Moreover, the variation of the ramp slope will also bring a few modifications to the wall voltage. The priming particles in the beginning of the addressing period are related to the slope of the ramping down voltage pulse. The simulation results can help us optimize the driving scheme of the SM-PDP

The labyrinthine portion of the facial canal in patients with Bell's palsy investigated by computed tomography

International Nuclear Information System (INIS)

Wadin, K.; Thomander, L.; Wilbrand, H.

1987-01-01

The reproducibility of the labyrinthine portion of the facial canal by computed tomography was investigated in 22 patients with Bell's palsy. The CT images were compared with those obtained in 18 temporal bone specimens. Measurements of the diameters of different parts of the facial canal were made of these images and also microscopically in plastic casts of the temporal bone specimens. No marked difference was found between the dimensions of the labyrinthine portion of the facial canal of the involved and healthy temporal bone in the patient, nor did these differ from the dimensions in the specimens. CT of the slender, curved labyrinthine portion was found to be of doubtful value for metric estimation of small differences in width. The anatomic variations of the canal rendered the evaluation more difficult. CT with a slice thickness of 2 mm was of no value for assessment of this part of the canal. Measurement of the diameters of the labyrinthine portion on CT images is an inappropriate and unreliable method for clinical purposes. (orig.)

Third Expert Consultation on RAMP (RAMP III) (Helsinki, Finland, September 13, 15 and 20, 1986). Final Report.

Science.gov (United States)

United Nations Educational, Scientific and Cultural Organization, Paris (France). General Information Programme.

Organized for the United Nations Educational, Scientific, and Cultural Organization (Unesco) by contract with the International Council on Archives (ICA), this meeting concerning the Records and Archives Management Programme (RAMP) was attended by 14 experts invited from Unesco member countries. Following a brief introduction, summaries are…

LHC Report: Intensity ramp-up

CERN Multimedia

Mike Lamont for the LHC Team

2012-01-01

The first stable beams at 4 TeV were declared on Thursday, 5 April with 3 bunches per beam. This marked the start of the intensity ramp-up, which aims to get back up to 1380 bunches per beam as quickly as is safely possible.   The next couple of days saw fills with 47, 84 and 264 bunches per beam and on Sunday, 8 April the move was made to 624 bunches. With the squeeze to 60 cm in place, 624 bunches with reasonably high bunch intensities of around 1.3 to 1.4 x1011 protons per bunch have already yielded respectable peak luminosities of up to 2.5 x1033 cm-2s-1. Following a lot of hard work during the Christmas technical stop, machine availability is very good at the moment. The ramp-up in the number of bunches is accompanied by a series of checks aimed to make sure the machine protection systems and operational procedures are in a good enough shape to safely deal with the beam intensity. 624 bunches at 4 TeV already represents an energy over 50 MJ and serious damage potential. The next few days sh...

High power fast ramping power supplies

Energy Technology Data Exchange (ETDEWEB)

Marneris,I.; Bajon, E.; Bonati, R.; Sandberg, J.; Roser, T.; Tsoupas, N.

2009-05-04

Hundred megawatt level fast ramping power converters to drive proton and heavy ion machines are under research and development at accelerator facilities in the world. This is a leading edge technology. There are several topologies to achieve this power level. Their advantages and related issues will be discussed.

Influence of the ramp angle on levitation characteristics of HTS maglev

International Nuclear Information System (INIS)

He Qingyong; Wang Jiasu; Zhang Longcai; Wang Suyu; Pan Siting

2008-01-01

The gradeability is one of the advantages of the high-temperature superconducting (HTS) maglev vehicle, and it is relative to the levitation characteristic of the maglev system on the ramp. The influence of the ramp angle on the levitation characteristics of the HTS maglev model was investigated. Some levitation characteristic parameters on the uphill guideway with different ramp angles were studied by the equivalent experiment, such as the levitation force, the levitation gap, the levitation stiffness and the guidance force. Compared with the experimental results on the horizontal guideway, it was found that the levitation gap increased, but the levitation force and the levitation stiffness decreased. The levitation gap and the levitation stiffness are considered as the main maglev characteristic parameters needed to be taken into account

Structural studies of YBCO ramp Josephson junctions for rapid single flux quantum circuits

Energy Technology Data Exchange (ETDEWEB)

Gustafsson, M.; Olsson, E.; Huang, M.Q.; Komissinski, P.V.; Mozhaev, P.B.; Ivanov, Z.G.

1999-11-01

Ramp-type Josephson junctions with barrier layers of Ga doped PrBa{sub 2}Cu{sub 3}O{sub 7{minus}{delta}} have been investigated using scanning and transmission electron microscopy. The microstructures have been correlated to the ramp geometry. The junctions exhibited low excess current. This is believed to be due to the uniform thickness of barrier layer deposited on the ion-milled edges. The uniformity of the barrier is presumed to be a result of the smooth ramp, which promoted uniform nucleation and epitaxial growth.

Development of 3He-BOCA power ramping facility, 1

International Nuclear Information System (INIS)

Nakata, Hirokatsu; Ishii, Tadahiko; Itoh, Haruhiko; Abe, Hiroshi; Nakazaki, Chozaburo

1979-11-01

Development of a He-3 power controlled boiling water capsule, 3 He-BOCS, for LWR fuels power ramping test in JMTR has been carried out since 1978 on a five-year program; in the reactor, irradiation tests of various fuels and structual materials have been made since 1969. Using stagnant-pressurized water as a thermal medium, the capsule provides pressure and temperature conditions similar to those in LWRs. Heat generation of a fuel pin can be controlled by a He-3 gas screen surrounding the capsule. The facility is capable of testing numbers of both fresh and irradiated fuel pins under LWR operating conditions for power ramping and cycling. After explaining the operating priciples of 3 He-BOCA and the development program, the following are described: the results of preliminary out-of-pile test on heat conductive characteristics of the capsule and a conceptual design of the 3 He-BOCA for power ramping of a short fuel pin from 250 W/cm to 500 W/cm under BWR conditions. (author)

Probabilistic Wind Power Ramp Forecasting Based on a Scenario Generation Method

Energy Technology Data Exchange (ETDEWEB)

Wang, Qin [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Florita, Anthony R [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Krishnan, Venkat K [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Hodge, Brian S [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Cui, Mingjian [University of Texas at Dallas; Feng, Cong [University of Texas at Dallas; Wang, Zhenke [University of Texas at Dallas; Zhang, Jie [University of Texas at Dallas

2018-02-01

Wind power ramps (WPRs) are particularly important in the management and dispatch of wind power and currently drawing the attention of balancing authorities. With the aim to reduce the impact of WPRs for power system operations, this paper develops a probabilistic ramp forecasting method based on a large number of simulated scenarios. An ensemble machine learning technique is first adopted to forecast the basic wind power forecasting scenario and calculate the historical forecasting errors. A continuous Gaussian mixture model (GMM) is used to fit the probability distribution function (PDF) of forecasting errors. The cumulative distribution function (CDF) is analytically deduced. The inverse transform method based on Monte Carlo sampling and the CDF is used to generate a massive number of forecasting error scenarios. An optimized swinging door algorithm is adopted to extract all the WPRs from the complete set of wind power forecasting scenarios. The probabilistic forecasting results of ramp duration and start-time are generated based on all scenarios. Numerical simulations on publicly available wind power data show that within a predefined tolerance level, the developed probabilistic wind power ramp forecasting method is able to predict WPRs with a high level of sharpness and accuracy.

Emittance Growth due to Crab Cavity Ramping for LHC Beam-1 Lattice

CERN Document Server

Morita, A

2008-01-01

In LHC upgrade scenarios using global crab crossing, it is desired to turn on the crab cavity only at top energy. Turning on the crab cavity could increase the emittance of the stored beam, since the transverse kick of the crab cavity excites betatron oscillations. For a sufficiently slow ramping speed of the crab cavity voltage, however, the changes in z-dependent closed orbit are sufficiently adiabatic that the emittance growth becomes negligible. In order to determine the safe ramping speed of the LHC crab-cavity voltage, the dependence of the emittance growth on the ramping speed is estimated via a 6D particle-tracking simulation.

Improving short-term forecasting during ramp events by means of Regime-Switching Artificial Neural Networks

Science.gov (United States)

Gallego, C.; Costa, A.; Cuerva, A.

2010-09-01

Since nowadays wind energy can't be neither scheduled nor large-scale storaged, wind power forecasting has been useful to minimize the impact of wind fluctuations. In particular, short-term forecasting (characterised by prediction horizons from minutes to a few days) is currently required by energy producers (in a daily electricity market context) and the TSO's (in order to keep the stability/balance of an electrical system). Within the short-term background, time-series based models (i.e., statistical models) have shown a better performance than NWP models for horizons up to few hours. These models try to learn and replicate the dynamic shown by the time series of a certain variable. When considering the power output of wind farms, ramp events are usually observed, being characterized by a large positive gradient in the time series (ramp-up) or negative (ramp-down) during relatively short time periods (few hours). Ramp events may be motivated by many different causes, involving generally several spatial scales, since the large scale (fronts, low pressure systems) up to the local scale (wind turbine shut-down due to high wind speed, yaw misalignment due to fast changes of wind direction). Hence, the output power may show unexpected dynamics during ramp events depending on the underlying processes; consequently, traditional statistical models considering only one dynamic for the hole power time series may be inappropriate. This work proposes a Regime Switching (RS) model based on Artificial Neural Nets (ANN). The RS-ANN model gathers as many ANN's as different dynamics considered (called regimes); a certain ANN is selected so as to predict the output power, depending on the current regime. The current regime is on-line updated based on a gradient criteria, regarding the past two values of the output power. 3 Regimes are established, concerning ramp events: ramp-up, ramp-down and no-ramp regime. In order to assess the skillness of the proposed RS-ANN model, a single

Windscale nuclear power development laboratories power ramp experience in the Winfrith SGHWR (UK)

International Nuclear Information System (INIS)

Garlick, A.; Sumerling, R.; Stuttard, A.; Bond, G.G.; Howl, D.A.; Fox, W.N.; Cordall, D.; Cornell, R.M.

SGHWR fuel has sufficient power ramping capability to permit considerable latitude in fuel management schemes. However, beyond some limiting ramping conditions, there is risk of fuel defecting. Controlled ramp experiments were therefore carried out in the reactor in order to determine the defect mechanism and define the fuel operating limitations. Cladding cracks produced during these power ramps are considered to have been a consequence of fission product stress-corrosion attack. A critical stress level for cracking, based on laboratory stress corrosion tests, have been used successfully in conjunction with computer codes to calculate cladding stresses and strains in fuel rods. Initial analysis of the conditions under which a fuel element defected at 11.6 MWd/kgU suggests that the threshold stress for failure may be decreased compared with elements at lower burn-up (5-6 MWd/kgU)

Power ramp tests of MOX fuel rods. HBWR irradiation with the instrument rig, IFA-591

International Nuclear Information System (INIS)

Ozawa, Takayuki; Abe, Tomoyuki

2006-03-01

Plutonium-uranium mixed oxide (MOX) fuel rods of instrumental rig IFA-591 were ramped in HBWR to study the Advanced Thermal Reactor (ATR) MOX fuel behavior during transient operation and to determine a failure threshold of the MOX fuel rods. Eleven segments were base-irradiated in ATR 'FUGEN' up to 18.4 GWd/t. Zirconium liner claddings were adopted for four segments of them. As the results of non-destructive post irradiation examinations (PIEs) after the base-irradiation and before the ramp tests, no remarkable behavior affecting the integrity of fuel assembly and fuel rod was confirmed. All segments to be used for the ramp tests, which consisted of the multi-step ramp tests and the single-step ramp tests, had instrumentations for in-pile measurements of cladding elongation or plenum pressure, and heated up to the maximum linear power of 58.3-68.4 kW/m without failure. The major results of ramp tests are as follows: There is no difference in PCMI behaviors between two type rods of Zry-2 and Zirconium liner claddings from the in-pile measurements of cladding elongation and plenum pressure. The computations of cladding elongation and inner pressure gave slightly lower elongation and pressure than the in-pile measurements during the ramp-test. However, the cladding relaxation during the power hold was in good agreement, and the fission gas release behavior during cooling down could be evaluated by taking into account the relaxation of contact pressure between pellet and cladding. Although the final power during IFA-591 ramp tests reached the higher linear power than the failure threshold power of UO 2 fuel rods, no indication of fuel failure was observed during the ramp tests. The cladding relaxation due to the creep deformation of the MOX pellets at high temperature could be confirmed at the power steps during the multi-ramp test. The fission gas release due to the emancipation from PCMI stress was observed during the power decreasing. The burn-up dependence could be

ALTERNATIVE MATERIALS FOR RAMP-EDGE SNS JUNCTIONS

International Nuclear Information System (INIS)

Jia, Q.; Fan, Y.; Gim, Y.

1999-01-01

We report on the processing optimization and fabrication of ramp-edge high-temperature superconducting junctions by using alternative materials for both superconductor electrodes and normal-metal barrier. By using Ag-doped YBa 2 Cu 3 O 7-x (Ag:YBCO) as electrodes and a cation-modified compound of (Pr y Gd 0.6-y )Ca 0.4 Ba 1.6 La 0.4 Cu 3 O 7 (y = 0.4, 0.5, and 0.6) as a normal-metal barrier, high-temperature superconducting Josephson junctions have been fabricated in a ramp-edge superconductor/normal-metal/superconductor (SNS) configuration. By using Ag:YBCO as electrodes, we have found that the processing controllability /reproducibility and the stability of the SNS junctions are improved substantially. The junctions fabricated with these alternative materials show well-defined RSJ-like current vs voltage characteristics at liquid nitrogen temperature

Performance evaluation of UO2-Zr fuel in power ramp tests

International Nuclear Information System (INIS)

Knudsen, P.; Bagger, C.

1977-01-01

In power reactors using UO 2 -Zr fuel, rapid power increases may lead to failures in fuel pins that have been irradiated at steady or decreasing heat loads. This paper presents results which extend the experience with power ramp performance of high burn-up fuel pins. A test fuel element containing both pellet and vipac UO 2 -Zr fuel pins was irradiated in the HBWR at Halden for effectively 2 1/2 years to an average burn-up of 21,000 MWD/te UO 2 at gradually decreasing power levels. The subsequent non-destructive characterization revealed formation of transverse cracks in the vipac fuel columns. After the HBWR irradiation, five of the fuel pins were power ramp tested individually in the DR 3 Reactor at Riso. The ramp rates in this test series were in the range 3-60 W/cm min. The maximum local heat loads seen in the ramp tests were 20-120% above the highest levels experienced at the same axial positions during the HBWR irradiation. Three pellets and one vipac fuel pin failed, whereas another vipac pin gave no indication of clad penetration. Profilometry after the ramp testing indicated the formation of small ridges for both types of fuel pins. For vipac fuel, the ridges were less regularly distributed along the pin length than for pellet fuel. Neutron radiography revealed the formation of additional transverse and longitudinal fuel cracks during the power ramps for both types of fuel pins. The observed failures seemed to be marginal since little or no indication as to the locations of the clad penetrations could be derived from the non-destructive post-irradiation examinations. The cases have been analyzed by means of the Danish fuel performance codes. The calculations, which are in general agreement with the observations, are discussed. The results of the investigations indicate qualitative similarities in over power performance of the two fuel types

The ramp rate dependence of the sextupole field in superconducting dipoles

International Nuclear Information System (INIS)

Ghosh, A.K.; Robins, K.E.; Sampson, W.B.

1993-01-01

Sextupole components are induced in the magnetic field of superconducting dipoles when the current is changed. The magnitude of this effect depends on the rate of change of field, the strand-to-strand resistance in the superconducting cable, and the twist pitch of the wire. Ramp rate measurements have been made on a number of SSC dipoles wound from conductors with different interstrand resistances. The technique employed uses an array of Hall probes sensitive to the sextupole field and can measure the difference for field increasing or decreasing as a function of axial position. Magnets with very low interstrand resistance exhibit a large axial oscillation in the sextupole field between up and down ramps which is rate dependent When the strand resistance is high the amplitude of this oscillation is almost independent of ramp rate

Quantification of tsunami-induced flows on a Mediterranean carbonate ramp reveals catastrophic evolution

NARCIS (Netherlands)

Slootman, A.; Cartigny, M.J.B.; Moscariello, A.; Chiaradia, M.; de Boer, P.L.

2016-01-01

Cool-water carbonates are the dominant limestones in the Mediterranean Basin since the Early Pliocene. Their deposition typically resulted in ramp morphologies due to high rates of resedimentation. Several such fossil carbonate ramps are characterised by a bimodal facies stacking pattern, where

Combined Ramp and Squeeze to 6.5 TeV in the LHC

CERN Document Server

Solfaroli Camillocci, Matteo; Tomás, Rogelio; Wenninger, Jorg

2016-01-01

The cycle of the LHC is composed of an energy ramp followed by a betatron squeeze, needed to reduce the beta- star value in the interaction points. Since Run 1, studies have been carried out to investigate the feasibility of combining the two operations, thus considerably reducing the duration of the operational cycle. In Run 2, the LHC is operating at the energy of 6.5 TeV that requires a much longer cycle than that of Run 1. Therefore, the performance gains from a Combined Ramp and Squeeze (CRS) is more interesting. Merging the energy ramp and the betatron squeeze could result in a gain of several minutes for each LHC cycle. With increasing maturity of LHC operation, it is now possible to envisage more complex beam manipulations; this paper describes the first machine experiment with beam, aiming at validating the combination of ramp and squeeze, which was performed in 2015, during a machine development phase. The operation experience with the LHC run at 2.51 TeV, when CRS down to 4 meters was deployed and ...

Pricing the Ramping Reserve and Capacity Reserve in Real Time Markets

OpenAIRE

Ye, Hongxing; Li, Zuyi

2015-01-01

The increasing penetration of renewable energy in recent years has led to more uncertainties in power systems. In order to maintain system reliability and security, electricity market operators need to keep certain reserves in the Security-Constrained Economic Dispatch (SCED) problems. A new concept, deliverable generation ramping reserve, is proposed in this paper. The prices of generation ramping reserves and generation capacity reserves are derived in the Affine Adjustable Robust Optimizat...

Labyrinthine portion of the facial canal in patients with Bell's palsy investigated by computed tomography

Energy Technology Data Exchange (ETDEWEB)

Wadin, K.; Thomander, L.; Wilbrand, H.

The reproducibility of the labyrinthine portion of the facial canal by computed tomography was investigated in 22 patients with Bell's palsy. The CT images were compared with those obtained in 18 temporal bone specimens. Measurements of the diameters of different parts of the facial canal were made of these images and also microscopically in plastic casts of the temporal bone specimens. No marked difference was found between the dimensions of the labyrinthine portion of the facial canal of the involved and healthy temporal bone in the patient, nor did these differ from the dimensions in the specimens. CT of the slender, curved labyrinthine portion was found to be of doubtful value for metric estimation of small differences in width. The anatomic variations of the canal rendered the evaluation more difficult. CT with a slice thickness of 2 mm was of no value for assessment of this part of the canal. Measurement of the diameters of the labyrinthine portion on CT images is an inappropriate and unreliable method for clinical purposes.

Analysis of failed ramps during the RHIC FY09 run

Energy Technology Data Exchange (ETDEWEB)

Minty, M. [Brookhaven National Lab. (BNL), Upton, NY (United States). Collider-Accelerator Dept.

2014-08-15

The Relativistic Heavy Ion Collider (RHIC) is a versatile accelerator that supports operation with polarized protons of up to 250 GeV and ions with up to 100 GeV/nucleon. During any running period, various operating scenarios with different particle species, beam energies or accelerator optics are commissioned. In this report the beam commissioning periods for establishing full energy beams (ramp development periods) from the FY09 run are summarized and, for the purpose of motivating further developments, we analyze the reasons for all failed ramps.

Analysis of failed ramps during the RHIC FY09 run

International Nuclear Information System (INIS)

Minty, M.

2014-01-01

The Relativistic Heavy Ion Collider (RHIC) is a versatile accelerator that supports operation with polarized protons of up to 250 GeV and ions with up to 100 GeV/nucleon. During any running period, various operating scenarios with different particle species, beam energies or accelerator optics are commissioned. In this report the beam commissioning periods for establishing full energy beams (ramp development periods) from the FY09 run are summarized and, for the purpose of motivating further developments, we analyze the reasons for all failed ramps.

Start-up and ramp-up of the PLT tokamak by lower hybrid waves

International Nuclear Information System (INIS)

Jobes, F.C.; Bernabei, S.; Chu, T.K.

1985-08-01

Lower hybrid waves have been used on the PLT tokamak both to start the plasma current and to ramp it up from pre-existing levels. The waves, at 800 MHz, were launched from a 6-waveguide grill. The phasing between adjacent guides could be selected electronically, and thus the launched spectrum could be set and changed at will. For start-up, the waveguide phase difference was initially set at 0 0 in order to create a plasma, then switched to 90 0 to drive the current. Over 100 kA of plasma current, at a density of 0.5 to 1 x 10 12 cm -3 , was generated in this manner. Ramp-up experiments were performed under a wide variety of conditions. The most efficient ramp-up was found at the lowest plasma densities and with the fastest launched spectrum (n/sub e/ approx. 2 x 10 12 cm -3 , N/sub parallel/ approx. 1.6 peak); approx.20% of the launched RF power was converted to (increased) poloidal field energy. All of the ramp-up results are in excellent agreement with a theory which determines the efficiency of ramp-up from the consideration of the relative energy losses of the superthermal current-carrying electrons to collisions and to the opposing inductive E-field

Numerical investigation of over expanded flow behavior in a single expansion ramp nozzle

Science.gov (United States)

Mousavi, Seyed Mahmood; Pourabidi, Reza; Goshtasbi-Rad, Ebrahim

2018-05-01

The single expansion ramp nozzle is severely over-expanded when the vehicle is at low speed, which hinders its ability to provide optimal configurations for combined cycle engines. The over-expansion leads to flow separation as a result of shock wave/boundary-layer interaction. Flow separation, and the presence of shocks themselves, result in a performance loss in the single expansion ramp nozzle, leading to reduced thrust and increased pressure losses. In the present work, the unsteady two dimensional compressible flow in an over expanded single expansion ramp nozzle has been investigated using finite volume code. To achieve this purpose, the Reynolds stress turbulence model and full multigrid initialization, in addition to the Smirnov's method for examining the errors accumulation, have been employed and the results are compared with available experimental data. The results show that the numerical code is capable of predicting the experimental data with high accuracy. Afterward, the effect of discontinuity jump in wall temperature as well as the length of straight ramp on flow behavior have been studied. It is concluded that variations in wall temperature and length of straight ramp change the shock wave boundary layer interaction, shock structure, shock strength as well as the distance between Lambda shocks.

Field test of coordinated ramp metering (CRM).

Science.gov (United States)

2017-03-15

This project has focused on field implementation and testing of a Coordinated Ramp Metering (CRM) algorithm at California State Route 99 : Northbound corridor in Sacramento between Calvine Road and the SR50 interchange after 12th Ave. It is a 9 mile ...

Inter-Organisational Coordination in Ramp-Up Execution

DEFF Research Database (Denmark)

Christensen, Irene; Karlsson, Christer

the degree of fragmentation in the process planning and execution. Resource dependence theory (RDT) is used as central explanatory framework for inter-organisational interdependencies formation throughout the planning and execution of the ramp-up activities and milestones. This study aims at exploring inter...

Efficiency promotion for an on-ramp system based on intelligent transportation system information

International Nuclear Information System (INIS)

Dong-Fan, Xie; Zi-You, Gao; Xiao-Mei, Zhao

2010-01-01

The effect of cars with intelligent transportation systems (ITSs) on traffic flow near an on-ramp is investigated by car-following simulations. By numerical simulations, the dependences of flux on the inflow rate are investigated for various proportions of cars with ITSs. The phase diagrams as well as the spatiotemporal diagrams are presented to show different traffic flow states on the main road and the on-ramp. The results show that the saturated flux on the main road increases and the free flow region is enlarged with the increase of the proportion of cars with ITS. Interestingly, the congested regions of the main road disappear completely when the proportion is larger than a critical value. Further investigation shows that the capacity of the on-ramp system can be promoted by 13% by using the ITS information, and the saturated flux on the on-ramp can be kept at an appropriate value by adjusting the proportion of cars with ITS. (general)

Current ramp-up experiments in full current drive plasmas in TRIAM-1M

International Nuclear Information System (INIS)

Hanada, K.; Nakamura, K.; Hasegawa, M.; Itoh, S.; Zushi, H.; Sakamoto, M.; Jotaki, E.; Iyomasa, A.; Kawasaki, S.; Nakashima, H.; Yoshida, N.; Tokunaga, K.; Fujiwara, T.; Kulkarni, S.V.; Mitarai, O.

2004-01-01

Four types of plasma current ramp-up experiments in full non-inductively lower hybrid current driven (LHCD) plasmas were executed in TRIAM-1M: (1) current start-up by a combination of electron cyclotron resonance heating (ECRH) and LHCD, (2) tail heating by additional LHCD, (3) bulk heating by ECRH and (4) spontaneous ramp-up by a transition to enhanced current drive (ECD) mode. The time evolutions of plasma current during four types of ramp-up phase were adjusted by a simple model with two different time constants, which are a time defined by the total current diffusion time and a time constant for improving the current drive efficiency. In the case of (1) and (4), the latter time constant is significant during the current ramp-up phase. The improvement in the current drive efficiency in the ECD mode is likely to be caused by the increase in the effective refractive index along the magnetic field of the lower hybrid wave. (author)

Performance of the ramping power supplies for the APS booster synchrotron

International Nuclear Information System (INIS)

Carwardine, J.A.; Milton, S.V.; McGhee, D.G.

1995-01-01

The Advanced Photon Source (APS) booster ramp cycle is completed within 250ms and repeated at 2Hz. Separate phase-controlled power supplies deliver current to each of the dipole, quadrupole, and sextupole magnet families. Tracking requirements are particularly challenging because of the fast (non-resonant) ramp. In order to meet the requirements, both conventional regulation and cycle-to-cycle adaptation are used. The power supply system and its performance are described

Report on the access to the deposition areas of the repository. Shaft or Ramp?

International Nuclear Information System (INIS)

Baeckblom, Goeran; Christiansson, Rolf; Hedin, Allan; Norman, Fredrik; Lagerstedt, Leif

2003-05-01

During year 2002, SKB launched the site-specific engineering of the repository at the Oskarshamn and Oesthammar candidate sites. A part of the ongoing engineering work is to evaluate and possibly select type of access from surface to the underground deposition areas located at a depth of some 400 to 700 metres below the surface. The project objectives are to provide a basis for comparison and to compare generic options for access routes to the underground deposition areas, to formulate preliminary Design Justification Statements for the continued site-specific engineering of access routes to the underground repository and also to describe and exemplify methodology for optimisation of the repository engineering. In consideration of the requirements of SKB, several alternative access options are explored. The main alternatives are a ramp with one or two operational areas at the surface, a ramp with parallel excavation of a blind shaft and an alternative with shafts only. A suite of objective functions were employed in the evaluation of the main alternatives relating to long-term safety, occupational safety during construction and operation, environmental impact, sustainability of natural resources, total cost, schedules, flexibility and project risks. All alternatives studied are feasible and safe, but the alternative with a spiral ramp and a blind shaft is deemed to be the most favourable option. The alternative has the highest flexibility without any tangible disadvantages related neither to long-term safety, environmental impact nor to schedules. It is an advantage that ramp traffic is drastically reduced as rock and backfilling material is transported by the skip rather than by vehicles in the ramp, thereby reducing risks of accidents and fires in the ramp. The concurrent ramp and shaft excavation also shorten the construction period with 18 months for the underground excavations. The discounted total cost is however 100 million Swedish Kronor higher for this

Probabilistic Wind Power Ramp Forecasting Based on a Scenario Generation Method: Preprint

Energy Technology Data Exchange (ETDEWEB)

Wang, Qin [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Florita, Anthony R [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Krishnan, Venkat K [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Hodge, Brian S [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Cui, Mingjian [Univ. of Texas-Dallas, Richardson, TX (United States); Feng, Cong [Univ. of Texas-Dallas, Richardson, TX (United States); Wang, Zhenke [Univ. of Texas-Dallas, Richardson, TX (United States); Zhang, Jie [Univ. of Texas-Dallas, Richardson, TX (United States)

2017-08-31

Wind power ramps (WPRs) are particularly important in the management and dispatch of wind power, and they are currently drawing the attention of balancing authorities. With the aim to reduce the impact of WPRs for power system operations, this paper develops a probabilistic ramp forecasting method based on a large number of simulated scenarios. An ensemble machine learning technique is first adopted to forecast the basic wind power forecasting scenario and calculate the historical forecasting errors. A continuous Gaussian mixture model (GMM) is used to fit the probability distribution function (PDF) of forecasting errors. The cumulative distribution function (CDF) is analytically deduced. The inverse transform method based on Monte Carlo sampling and the CDF is used to generate a massive number of forecasting error scenarios. An optimized swinging door algorithm is adopted to extract all the WPRs from the complete set of wind power forecasting scenarios. The probabilistic forecasting results of ramp duration and start time are generated based on all scenarios. Numerical simulations on publicly available wind power data show that within a predefined tolerance level, the developed probabilistic wind power ramp forecasting method is able to predict WPRs with a high level of sharpness and accuracy.

Startup Ramp Rate Analysis for the OPR1000 Using FALCON Code

Energy Technology Data Exchange (ETDEWEB)

Kim, Ki-Young; Jung, Sung-hwan; Kim, Yong-Deok [Korea Hydro and Nuclear Power Co. Ltd, Daejeon (Korea, Republic of)

2015-05-15

Pelletcladding interaction (PCI) fuel failure results from a combination of mechanical and chemical interactions between the UO2 fuel pellets and Zircaloy cladding. Under restart operation conditions, the pellet-cladding gap may be closed and the differential thermal expansion can result in the stress concentrations on the cladding that may cause the fuel failure. This paper summarizes the PCI sensitivity assessment of the PLUS7 fuel during the OPR1000 startup. The objective of the PCI analysis is to assess the cladding stress state under various power ramp conditions at the peak power node location. Fuel-cladding gap is closed at about 10,000 MWD/MTU burnup. Maximum hoop stress is not sensitive about change of startup ramp rate in 0 - 40% power range. Maximum hoop stress is not sensitive about the intermittent increase(1%) of startup ramp rate in 40 - 100% power range.

Startup Ramp Rate Analysis for the OPR1000 Using FALCON Code

International Nuclear Information System (INIS)

Kim, Ki-Young; Jung, Sung-hwan; Kim, Yong-Deok

2015-01-01

Pelletcladding interaction (PCI) fuel failure results from a combination of mechanical and chemical interactions between the UO2 fuel pellets and Zircaloy cladding. Under restart operation conditions, the pellet-cladding gap may be closed and the differential thermal expansion can result in the stress concentrations on the cladding that may cause the fuel failure. This paper summarizes the PCI sensitivity assessment of the PLUS7 fuel during the OPR1000 startup. The objective of the PCI analysis is to assess the cladding stress state under various power ramp conditions at the peak power node location. Fuel-cladding gap is closed at about 10,000 MWD/MTU burnup. Maximum hoop stress is not sensitive about change of startup ramp rate in 0 - 40% power range. Maximum hoop stress is not sensitive about the intermittent increase(1%) of startup ramp rate in 40 - 100% power range

A New Macro Model for Traffic Flow on a Highway with Ramps and Numerical Tests

International Nuclear Information System (INIS)

Tang Tieqiao; Huang Haijun; Zhang Ying; Wong, S.C.; Gao Ziyou

2009-01-01

In this paper, we present a new macro model for traffic flow on a highway with ramps based on the existing models. We use the new model to study the effects of on-off-ramp on the main road traffic during the morning rush period and the evening rush period. Numerical tests show that, during the two rush periods, these effects are often different and related to the status of the main road traffic. If the main road traffic flow is uniform, then ramps always produce stop-and-go traffic when the main road density is between two critical values, and ramps have little effect on the main road traffic when the main road density is less than the smaller critical value or greater than the larger critical value. If a small perturbation appears on the main road, ramp may lead to stop-and-go traffic, or relieve or even eliminate the stop-and-go traffic, under different circumstances. These results are consistent with real traffic, which shows that the new model is reasonable.

Prosthodontic management of mandibular deviation using palatal ramp appliance

Directory of Open Access Journals (Sweden)

Prince Kumar

2012-08-01

Full Text Available Segmental resection of the mandible generally results in deviation of the mandible to the defective side. This loss of continuity of the mandible destroys the balance of the lower face and leads to decreased mandibular function by deviation of the residual segment toward the surgical site. Prosthetic methods advocated to reduce or eliminate mandibular deviation include intermaxillary fixation, removable mandibular guide flange, palatal ramp, implant-supported prosthesis and palatal guidance restorations which may be useful in reducing mandibular deviation and improving masticatory performance and efficiency. These methods and restorations would be combined with a well organized mandibular exercise regimen. This clinical report describes the rehabilitation following segmental mandibulectomy using palatal ramp prosthesis.

Hangingwall accomodation styles in flat ramp trust

NARCIS (Netherlands)

Mulugeta, G.; Sokoutis, D.

2003-01-01

In this paper we study the dynamic and rheologic control of hanging wall accommodation in ramp-flat thrust models. In particular we vary the dimensionless ratio of shear strength to gravity stress to model hanging wall accommodation styles in different materials. In all models we require that the

Off-ramps and on-ramps: keeping talented women on the road to success.

Science.gov (United States)

Hewlett, Sylvia Ann; Luce, Carolyn Buck

2005-03-01

Most professional women step off the career fast track at some point. With children to raise, elderly parents to care for, and other pulls on their time, these women are confronted with one off-ramp after another. When they feel pushed at the same time by long hours and unsatisfying work, the decision to leave becomes even easier. But woe to the woman who intends for that exit to be temporary. The on-ramps for professional women to get back on track are few and far between, the authors confirm. Their new survey research reveals for the first time the extent of the problem--what percentage of highly qualified women leave work and for how long, what obstacles they face coming back, and what price they pay for their time-outs. And what are the implications for corporate America? One thing at least seems clear: As market and economic factors align in ways guaranteed to make talent constraints and skill shortages huge issues again, employers must learn to reverse this brain drain. Like it or not, large numbers of highly qualified, committed women need to take time out of the workplace. The trick is to help them maintain connections that will allow them to reenter the workforce without being marginalized for the rest of their lives. Strategies for building such connections include creating reduced-hour jobs, providing flexibility in the workday and in the arc of a career, removing the stigma of taking time off, refusing to burn bridges, offering outlets for altruism, and nurturing women's ambition.

Start-up and ramp-up of the PLT tokamak by lower hybrid waves

International Nuclear Information System (INIS)

Jobes, F.C.; von Goeler, S.; Bernabei, S.

1985-01-01

Lower hybrid current drive (LHCD) is an inherently steady-state means of maintaining the poloidal field of a tokamak reactor. However, the energy losses of LHCD, which are proportional to density, are projected to be too great in a fusion reactor for LHCD to be economically feasible during the burn state of the reaction cycle. The authors maintain that LHCD could be extremely useful in restoring poloidal field energy between burns. In situations not requiring a rapid build up, LHCD appears, by extrapolation from present experiments, to be capable of supplying the full required poloidal field energy. In this paper, experiments have been performed on PLT and other tokamaks to examine the role of LHCD in start-up and ramp-up, as well as to examine the efficiency of stady-state current drice. Both the start-up and the ramp-up experiments were quite successful, with the start-up experiment obtaining currents up to 20% of full current for PLT, and the ramp-up experiments obtaining ramp-up efficiencies of approximately 20%

Development and testing of an innovative short-term large wind ramp forecasting system

Energy Technology Data Exchange (ETDEWEB)

Zack, J.W. [AWS Truepower LLC, Troy, NY (United States)

2010-07-01

This PowerPoint presentation discussed a ramp forecasting tool designed for use in a region of Texas with a high wind-generating capacity. Large system-wide ramps frequently occur in the region, and curtailments are common due to transmission constraints. The average hourly load of the power system is 32,101 MW. Wind power capacity in the region is 9382 MW. However, actual production rarely exceeds 6500 MW due to the curtailments. The short-term ramp forecasting tool was designed to aid in grid management decisions for the 0-6 hour ahead period as well as to address issues related to wind farm time series data and the lack of situational awareness information. The tool provided rapid updates for grid point wind analysis with feature detection and tracking algorithms and a rapid update cycle model. The tool also featured a suite of web-based applications that included deterministic ramp even forecasts, power production time series forecasts, and situational awareness products that are updated every 15 minutes. A performance evaluation study of the tool was provided. tabs., figs.

Studsvik SUPER-RAMP-II: 9x9 Project

International Nuclear Information System (INIS)

Djurle, S.

1991-12-01

EPRI participated in an international program involving ramp-testing of 9 x 9 fuel rod segments in a test reactor in Sweden. The principal objective was to establish the pellet-cladding interaction (PCI) failure threshold for this type of fuel. Several segmented fuel rods were irradiated in Dresden-2 BWR with time-averaged linear heat ratings ranging from 13 to 17 kW/m up to average burnup ranging from 26 to 34 MWd/kgU. The segments were subsequently subjected to ramp-testing in the R2 reactor at Studsvik Nuclear. The ramp-testing consisted of an initial irradiation of peak linear heat rating between 12 to 16 kW/m for about two hours, followed by a rapid increase to a power level in the range of 36 to 50 kW/m. The upper power level was maintained for twelve hours or until the fuel failure was detected. The study concluded that for 9 x 9 fuel type the PCI failure threshold is ∼38 kW/m, independent of the burnup in the range of 26 to 34 MWd/kgU. This failure threshold is about 5 kW/m greater than that of traditional 8 x 8 design. Although the significance of this difference can be argued, the interim and final fuel examinations performed in this project by destructive and nondestructive methods revealed valuable detailed information on fuel performance, which is also documented and discussed in this report

Suitability of representative electrochemical energy storage technologies for ramp-rate control of photovoltaic power

Science.gov (United States)

Jiang, Yu; Fletcher, John; Burr, Patrick; Hall, Charles; Zheng, Bowen; Wang, Da-Wei; Ouyang, Zi; Lennon, Alison

2018-04-01

Photovoltaic (PV) systems can exhibit rapid variances in their power output due to irradiance changes which can destabilise an electricity grid. This paper presents a quantitative comparison of the suitability of different electrochemical energy storage system (ESS) technologies to provide ramp-rate control of power in PV systems. Our investigations show that, for PV systems ranging from residential rooftop systems to megawatt power systems, lithium-ion batteries with high energy densities (up to 600 Wh L-1) require the smallest power-normalised volumes to achieve the ramp rate limit of 10% min-1 with 100% compliance. As the system size increases, the ESS power-normalised volume requirements are significantly reduced due to aggregated power smoothing, with high power lithium-ion batteries becoming increasingly more favourable with increased PV system size. The possibility of module-level ramp-rate control is also introduced, and results show that achievement of a ramp rate of 10% min-1 with 100% compliance with typical junction box sizes will require ESS energy and power densities of 400 Wh L-1 and 2300 W L-1, respectively. While module-level ramp-rate control can reduce the impact of solar intermittence, the requirement is challenging, especially given the need for low cost and long cycle life.

TRACY transient experiment databook. 2) ramp withdrawal experiment

International Nuclear Information System (INIS)

Nakajima, Ken; Yamane, Yuichi; Ogawa, Kazuhiko; Aizawa, Eiju; Yanagisawa, Hiroshi; Miyoshi, Yoshinori

2002-03-01

This is a databook of TRACY ''ramp withdrawal'' experiments. TRACY is a reactor to perform supercritical experiments using low-enriched uranyl nitrate aqueous solution. The excess reactivity of TRACY is 3$ at maximum, and it is inserted by feeding the solution to a core tank or by withdrawing a control rod, which is called as the transient rod, from the core. In the ramp withdrawal experiment, the supercritical experiment is initiated by withdrawing the transient rod from the core in a constant speed using a motor drive system. The data in the present databook consist of datasheets and graphs. Experimental conditions and typical values of measured parameters are tabulated in the datasheet. In the graph, power and temperature profiles are plotted. Those data are useful for the investigation of criticality accidents with fissile solutions, and for validation of criticality accident analysis codes. (author)

Development of the power ramping facility at JMTR

International Nuclear Information System (INIS)

Nakata, Hirokatsu; Sezaki, Katsuji; Nakazaki, Chosaburo; Ishii, Tadahiko; Ito, Haruhiko; Abe, Hiroshi

1985-03-01

The LWR fuel power ramping facility have been being developed at JMTR since 1978. This report, following previous reports, JAERI-M 8533 and 9343, summarizes the results of performance test performed in 1981 on the 3 He power controlled boiling water capsule, which is a basic part of the facility. Various measurements were carried out during reactor operation on each part of the capsule, i.e. capsule itself, capsule control unit and 3 He power control unit, after a long-time cold run test of the units. Through the test, it was confirmed that the capsule satisfies the specifications which stated that LWR fuel pin should be power-ramped under BWR conditions up to 50 kW/m with a change factor of more than 2, and that the control units operate in a good condition. (author)

An effective heuristic for combined heat-and-power production planning with power ramp constraints

International Nuclear Information System (INIS)

Rong, Aiying; Lahdelma, Risto

2007-01-01

Combined heat-and-power (CHP) production is an increasingly important technology for its efficient utilization of primary-energy resources and for reducing CO 2 emissions. In the CHP plant, the generation of heat-and-power follows a joint characteristic, which makes the determination of both the marginal power production cost (MPPC) and the feasible operating region for the plant more complicated than for the power-only generation plant. Due to the interdependence between heat and power production, the power-ramp constraints, which limit how much the power production of a CHP plant may increase or decrease between two successive periods, may also imply constraints on the heat production. In this paper, we investigate the impact of power-ramp constraints on CHP production planning and develop a robust heuristic for dealing with the power-ramp constraints based on the solution to the problem with relaxed ramp-constraints (RRC). Numerical results based on realistic production models show that the heuristic can generate high-quality solutions efficiently. (author)

Tamping Ramping: Algorithmic, Implementational, and Computational Explanations of Phasic Dopamine Signals in the Accumbens.

Directory of Open Access Journals (Sweden)

Kevin Lloyd

2015-12-01

Full Text Available Substantial evidence suggests that the phasic activity of dopamine neurons represents reinforcement learning's temporal difference prediction error. However, recent reports of ramp-like increases in dopamine concentration in the striatum when animals are about to act, or are about to reach rewards, appear to pose a challenge to established thinking. This is because the implied activity is persistently predictable by preceding stimuli, and so cannot arise as this sort of prediction error. Here, we explore three possible accounts of such ramping signals: (a the resolution of uncertainty about the timing of action; (b the direct influence of dopamine over mechanisms associated with making choices; and (c a new model of discounted vigour. Collectively, these suggest that dopamine ramps may be explained, with only minor disturbance, by standard theoretical ideas, though urgent questions remain regarding their proximal cause. We suggest experimental approaches to disentangling which of the proposed mechanisms are responsible for dopamine ramps.

Portion size and intended consumption. Evidence for a pre-consumption portion size effect in males?

Science.gov (United States)

Robinson, Eric; te Raa, Wesselien; Hardman, Charlotte A

2015-08-01

Larger portions increase energy intake (the 'portion size effect'); however, the mechanisms behind this effect are unclear. Although pre-meal intentions are thought to be an important determinant of energy intake, little research has examined how much of a meal individuals intend to eat when served standard versus larger portion sizes. Three studies examined the effect of manipulating portion size on intended food consumption. In Studies 1 (spaghetti bolognese) and 2 (curry and rice) male participants were shown an image of either a standard or a larger meal and indicated how much of the meal they intended to consume. In Study 3 male and female participants were served either a standard or a larger portion of ice cream for dessert, they indicated how much they intended to consume and then ate as much of the ice cream as they desired. Regardless of being shown standard or large portion sizes, in Studies 1 and 2 participants reported that they intended to eat the majority of the meal, equating to a large difference in intended energy consumption between portion size conditions (a 'pre-consumption portion size effect'). This finding was replicated in male participants in Study 3, although females intended to eat a smaller proportion of the larger portion of ice cream, compared to the standard portion. Both male and female participants tended to eat in accordance with their pre-meal intentions and a portion size effect on actual consumption was subsequently observed in males, but not in females. The portion size effect may be observed when measuring pre-meal intended consumption in males. Copyright © 2015. Published by Elsevier Ltd.

Visual exposure to large and small portion sizes and perceptions of portion size normality: Three experimental studies.

Science.gov (United States)

Robinson, Eric; Oldham, Melissa; Cuckson, Imogen; Brunstrom, Jeffrey M; Rogers, Peter J; Hardman, Charlotte A

2016-03-01

Portion sizes of many foods have increased in recent times. In three studies we examined the effect that repeated visual exposure to larger versus smaller food portion sizes has on perceptions of what constitutes a normal-sized food portion and measures of portion size selection. In studies 1 and 2 participants were visually exposed to images of large or small portions of spaghetti bolognese, before making evaluations about an image of an intermediate sized portion of the same food. In study 3 participants were exposed to images of large or small portions of a snack food before selecting a portion size of snack food to consume. Across the three studies, visual exposure to larger as opposed to smaller portion sizes resulted in participants considering a normal portion of food to be larger than a reference intermediate sized portion. In studies 1 and 2 visual exposure to larger portion sizes also increased the size of self-reported ideal meal size. In study 3 visual exposure to larger portion sizes of a snack food did not affect how much of that food participants subsequently served themselves and ate. Visual exposure to larger portion sizes may adjust visual perceptions of what constitutes a 'normal' sized portion. However, we did not find evidence that visual exposure to larger portions altered snack food intake. Copyright © 2015 The Authors. Published by Elsevier Ltd.. All rights reserved.

Evaluation of axial fission gas transport in power ramping experiments

International Nuclear Information System (INIS)

Kinoshita, Motoyasu

1986-01-01

The LINUS code calculates advective and diffusional transport of fission gas towards an upper plenum through the pellet-cladding gap. The basic equations were modified for analyzing a multi-component gas mixture in the gap and also for dealing with opening and/or closing of the gap, which induces additional axial gas flow. Analysis of the Petten ramp experiment shows that helium pressurization is effective in suppressing an ascending rate of fission gas concentration. After the maximum concentration is achieved through power ramping, the gas concentration could be described by a steady state analytical solution which does not depend on the filling gas pressure. (author)

TRACY transient experiment databook. 3) Ramp feed experiment

Energy Technology Data Exchange (ETDEWEB)

Nakajima, Ken; Yamane, Yuichi; Ogawa, Kazuhiko; Aizawa, Eiju; Yanagisawa, Hiroshi; Miyoshi, Yoshinori [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

2002-03-01

This is a databook of TRACY ''ramp feed'' experiments. TRACY is a reactor to perform supercritical experiments using low-enriched uranyl nitrate aqueous solution. The excess reactivity of TRACY is 3$ at maximum, and it is inserted by feeding the solution to a core tank or by withdrawing a control rod, which is called as the transient rod, from the core. In the ramp feed experiment, the supercritical experiment is initiated by feeding the fuel solution to the core tank in a constant feed rate. The data in the present databook consist of datasheets and graphs. Experimental conditions and typical values of measured parameters are tabulated in the datasheet. In the graph, power and temperature profiles are plotted. Those data are useful for the investigation of criticality accidents with fissile solutions, and for validation of criticality accident analysis codes. (author)

True Triaxial Experimental Study of Rockbursts Induced By Ramp and Cyclic Dynamic Disturbances

Science.gov (United States)

Su, Guoshao; Hu, Lihua; Feng, Xiating; Yan, Liubin; Zhang, Gangliang; Yan, Sizhou; Zhao, Bin; Yan, Zhaofu

2018-04-01

A modified rockburst testing system was utilized to reproduce rockbursts induced by ramp and cyclic dynamic disturbances with a low-intermediate strain rate of 2 × 10-3-5 × 10-3 s-1 in the laboratory. The experimental results show that both the ramp and cyclic dynamic disturbances play a significant role in inducing rockbursts. In the tests of rockbursts induced by a ramp dynamic disturbance, as the static stress before the dynamic disturbance increases, both the strength of specimens and the kinetic energy of the ejected fragments first increase and then decrease. In the tests of rockbursts induced by a cyclic dynamic disturbance, there exists a rockburst threshold of the static stress and the dynamic disturbance amplitude, and the kinetic energy of the ejected fragments first increases and then decreases as the cyclic dynamic disturbance frequency increases. The main differences between rockbursts induced by ramp dynamic disturbances and those induced by cyclic dynamic disturbances are as follows: the rockburst development process of the former is characterized by an impact failure feature, while that of the latter is characterized by a fatigue failure feature; the damage evolution curve of the specimen of the former has a leap-developing form with a significant catastrophic feature, while that of the latter has an inverted S-shape with a remarkable fatigue damage characteristic; the energy mechanism of the former involves the ramp dynamic disturbance giving extra elastic strain energy to rocks, while that of the latter involves the cyclic dynamic disturbance decreasing the ultimate energy storage capacity of rocks.

Experiencing Production Ramp-Up Education for Engineers

Science.gov (United States)

Bassetto, S.; Fiegenwald, V.; Cholez, C.; Mangione, F.

2011-01-01

This paper presents a game of industrialisation, based on a paper airplane, that mimics real world production ramp-up and blends classical engineering courses together. It is based on a low cost product so that it can be mass produced. The game targets graduate students and practitioners in engineering fields. For students, it offers an experiment…

A tunable electron beam source using trapping of electrons in a density down-ramp in laser wakefield acceleration.

Science.gov (United States)

Ekerfelt, Henrik; Hansson, Martin; Gallardo González, Isabel; Davoine, Xavier; Lundh, Olle

2017-09-25

One challenge in the development of laser wakefield accelerators is to demonstrate sufficient control and reproducibility of the parameters of the generated bunches of accelerated electrons. Here we report on a numerical study, where we demonstrate that trapping using density down-ramps allows for tuning of several electron bunch parameters by varying the properties of the density down-ramp. We show that the electron bunch length is determined by the difference in density before and after the ramp. Furthermore, the transverse emittance of the bunch is controlled by the steepness of the ramp. Finally, the amount of trapped charge depends both on the density difference and on the steepness of the ramp. We emphasize that both parameters of the density ramp are feasible to vary experimentally. We therefore conclude that this tunable electron accelerator makes it suitable for a wide range of applications, from those requiring short pulse length and low emittance, such as the free-electron lasers, to those requiring high-charge, large-emittance bunches to maximize betatron X-ray generation.

Prediction of power ramp defects - development of a physically based model and evaluation of existing criteria

International Nuclear Information System (INIS)

Notley, M.J.F.; Kohn, E.

2001-01-01

Power-ramp induced fuel failure is not a problem in the present CANDU reactors. The current empirical correlations that define probability of failure do not agree one-with-another and do not allow extrapolation outside the database. A new methodology, based on physical processes, is presented and compared to data. The methodology calculates the pre-ramp sheath stress and the incremental stress during the ramp, and whether or not there is a defect is predicted based on a failure threshold stress. The proposed model confirms the deductions made by daSilva from an empirical 'fit' to data from the 1988 PNGS power ramp failure incident. It is recommended that daSilvas' correlation be used as reference for OPG (Ontario Power Generation) power reactor fuel, and that extrapolation be performed using the new model. (author)

On the value and price-responsiveness of ramp-constrained storage

International Nuclear Information System (INIS)

Faghih, Ali; Roozbehani, Mardavij; Dahleh, Munther A.

2013-01-01

Highlights: • Derived the optimal policy and value function for ramp-constrained storage. • Gave analytic bound on long-term value, and explicit formulas for policy thresholds. • Value of storage saturates as capacity increases, regardless of price volatility. • In expectation, storage can induce high price elasticity near the mean price. • The buy/sell phase transition region in the price-state plane is steep. - Abstract: The primary concerns of this paper are twofold: understanding the value of storage in the presence of ramp constraints and exogenous energy prices, and understanding the implications of the associated optimal storage management policy for qualitative and quantitative characteristics of storage response to real-time prices. The optimal policy, along with the associated finite-horizon time-averaged value of storage, are analytically characterized in this paper. An analytical upper bound on the infinite-horizon time-averaged value of storage is also derived. This bound is valid for any achievable realization of prices when the support of the distribution is fixed, and highlights the dependence of the value of storage on ramp constraints and storage capacity. It is shown that while the value of storage is a non-decreasing function of price volatility, due to the finite ramp rate, the value of storage saturates quickly as the capacity increases, regardless of volatility. To study the implications of the optimal policy, computational experiments are presented that suggest optimal utilization of storage can, in expectation, induce a considerable amount of price elasticity near the average price. Then, a computational framework is presented for characterization of the behavior of storage as a function of price and the state of charge, which illustrates a steep buy/sell phase transition in the price-state plane

Chefs' opinions of restaurant portion sizes.

Science.gov (United States)

Condrasky, Marge; Ledikwe, Jenny H; Flood, Julie E; Rolls, Barbara J

2007-08-01

The objectives were to determine who establishes restaurant portion sizes and factors that influence these decisions, and to examine chefs' opinions regarding portion size, nutrition information, and weight management. A survey was distributed to chefs to obtain information about who is responsible for determining restaurant portion sizes, factors influencing restaurant portion sizes, what food portion sizes are being served in restaurants, and chefs' opinions regarding nutrition information, health, and body weight. The final sample consisted of 300 chefs attending various culinary meetings. Executive chefs were identified as being primarily responsible for establishing portion sizes served in restaurants. Factors reported to have a strong influence on restaurant portion sizes included presentation of foods, food cost, and customer expectations. While 76% of chefs thought that they served "regular" portions, the actual portions of steak and pasta they reported serving were 2 to 4 times larger than serving sizes recommended by the U.S government. Chefs indicated that they believe that the amount of food served influences how much patrons consume and that large portions are a problem for weight control, but their opinions were mixed regarding whether it is the customer's responsibility to eat an appropriate amount when served a large portion of food. Portion size is a key determinant of energy intake, and the results from this study suggest that cultural norms and economic value strongly influence the determination of restaurant portion sizes. Strategies are needed to encourage chefs to provide and promote portions that are appropriate for customers' energy requirements.

Ramp-up of CHI Initiated Plasmas on NSTX

International Nuclear Information System (INIS)

Mueller, D.; Bell, M.G.; Bell, R.E.; LeBlanc, B.; Roquemore, A.L.; Raman, R.; Jarboe, T.R.; Nelson, B.A.; Soukhanovskii, V.

2009-01-01

Experiments on the National Spherical Torus (NSTX) have now demonstrated flux savings using transient coaxial helicity injection (CHI). In these discharges, the discharges initiated by CHI are ramped up with an inductive transformer and exhibit higher plasma current than discharges without the benefit of CHI initiation.

Numerical studies on the ramped density plasma lens

International Nuclear Information System (INIS)

Williams, R.L.; Katsouleas, T.

1992-01-01

We consider the so-called adiabatic plasma lens when the plasma density is ramped too quickly to be considered adiabatic. The lens length can be much shorter in such a case, but the final spot size is shown to be larger by a factor of √1+α 2 than for a slowly ramped plasma lens with the same initial and final density (where α=-β'/2 is proportional to the plasma density gradient). We find that the final spot size is the same whether or not the Courant-Snyder parameters of the beam (α and β) are matched to the lens. However, matched beams allow the plasma density to be lower while unmatched beams allow the lens to be shorter (for the same α and for the same final to initial plasma density ratio). Finally, we find that a smaller spot size can be obtained for a given lens length and density ratio by starting at smaller α and increasing α along the lens

Engineering task plan for steam line ramp calculations

International Nuclear Information System (INIS)

DeSantis, G.N.; Freeman, R.D.

1994-01-01

The purpose of this document is to provide an approved work plan to perform calculations that verify the load limits of a proposed ramp over a steam line at the back side (East side) of SY Farm in support of work package 2W-94-00812/K. The objective of this supporting document is to provide Operations with a set of checked calculations that verify the ramp over the steam line at SY Farm will support a fully loaded concrete mixer truck without affecting the steam line. The calculations will be performed by an engineers from Facility Systems and independently checked and reviewed by another engineer. The calculations may then be added to the work package. If Operations decides to make any configuration changes to the steam line or surrounding area, Operations shall have these changes documented by an Engineering Change Notice (ECN). This ECN can be done by Facility Systems or any other engineering organization at the direction of Operations

Case Report of Multiembolic Cerebrovascular Event Associated with Ramp Study Echocardiogram

Directory of Open Access Journals (Sweden)

Brian C. Butera

2017-01-01

Full Text Available The incidence of ramp test echocardiogram-associated embolic events in the setting of therapeutic anticoagulation is likely rare and has not been reported. We present such a case in a patient with a HeartMate II left ventricular assist device (LVAD whose serial head computed tomography images, deteriorating clinical course, and the multiembolic nature of the event suggest causality. If the pretest probability of pump thrombosis in an individual LVAD patient is sufficiently high, the potential risks of performing a ramp study echocardiogram may not be warranted, even in the setting of adequate anticoagulation.

Tune and Chromaticity Control During Snapback and Ramp in 2015 LHC Operation

CERN Document Server

Schaumann, Michaela; Lamont, Mike; Solfaroli Camillocci, Matteo; Todesco, Ezio; Wenninger, Jorg

2016-01-01

Because of current redistribution on the superconducting cables, the harmonic components of the magnetic fields of the superconducting magnets in the Large Hadron Collider (LHC) show decay during the low field injection plateau. This results in tune and chromaticity variations for the beams. In the first few seconds of the ramp the original hysteresis state of the magnetic field is restored - the field snaps back. These fast dynamic field changes lead to strong tune and chromaticity excursions that, if not properly controlled, induce beam losses and potentially trigger a beam dump. A feed-forward system applies predicted corrections during the injection plateau and to the first part of the ramp to avoid violent changes of beam conditions. This paper discusses the snapback of tune and chromaticity as observed in 2015, as well as the control of beam parameters during the ramp. It also evaluates the quality of the applied feed-forward corrections and their reproducibility.

Integrated Variable Speed Limits Control and Ramp Metering for Bottleneck Regions on Freeway

Directory of Open Access Journals (Sweden)

Ming-hui Ma

2015-01-01

Full Text Available To enhance the efficiency of the existing freeway system and therefore to mitigate traffic congestion and related problems on the freeway mainline lane-drop bottleneck region, the advanced strategy for bottleneck control is essential. This paper proposes a method that integrates variable speed limits and ramp metering for freeway bottleneck region control to relieve the chaos in bottleneck region. To this end, based on the analyses of spatial-temporal patterns of traffic flow, a macroscopic traffic flow model is extended to describe the traffic flow operating characteristic by considering the impacts of variable speed limits in mainstream bottleneck region. In addition, to achieve the goal of balancing the priority of the vehicles on mainline and on-ramp, increasing capacity, and reducing travel delay on bottleneck region, an improved control model, as well as an advanced control strategy that integrates variable speed limits and ramp metering, is developed. The proposed method is tested in simulation for a real freeway infrastructure feed and calibrates real traffic variables. The results demonstrate that the proposed method can substantially improve the traffic flow efficiency of mainline and on-ramp and enhance the quality of traffic flow at the investigated freeway mainline bottleneck.

Power Ramp Limitation capabilities of Large PV Power Plants with Active Power Reserves

DEFF Research Database (Denmark)

Bogdan, Craciun; Kerekes, Tamas; Sera, Dezso

2017-01-01

Power Ramp Limitation (PRL) is likely to become a requirement for large scale photovoltaic power plants (LPVPPs) in order to allow the increase of PV penetration levels. Especially in islands with reduced inertia capability, this problem is more stringent: high power ramp can be caused by either...... fast irradiance changes or other participant generators for example wind power, or loads. In order to compensate for the power mismatch, LPVPPs must use Active Power Reserve (APR), by either curtailment or auxiliary storage. The paper proposes a PRL control structure for dynamic APR sizing...... and deployment. The selected test case is the power system of Puerto Rico (PREPA), modeled using the modified IEEE 12 bus benchmark system, with different levels of PV penetration. It is shown that LPVPP with PRL can effectively reduce the ramping rate of the participating generators. Considering that the large...

The influence of the magnetic field on the performance of an active magnetic regenerator (AMR)

DEFF Research Database (Denmark)

Bjørk, Rasmus; Engelbrecht, Kurt

2011-01-01

The influence of the time variation of the magnetic field, termed the magnetic field profile, on the performance of a magnetocaloric refrigeration device using the active magnetic regeneration (AMR) cycle is studied for a number of process parameters for both a parallel plate and packed bed...... temperature span and the maximum cooling capacity of 20–40% for both parallel plate and packed bed regenerators. The maximum cooling capacity is shown to depend very weakly on the ramp rate of the magnetic field. Reducing the temporal width of the high field portion of the magnetic field profile by 10% leads...

Visual exposure to large and small portion sizes and perceptions of portion size normality: Three experimental studies

OpenAIRE

Robinson, Eric; Oldham, Melissa; Cuckson, Imogen; Brunstrom, Jeffrey M.; Rogers, Peter J.; Hardman, Charlotte A.

2016-01-01

Portion sizes of many foods have increased in recent times. In three studies we examined the effect that repeated visual exposure to larger versus smaller food portion sizes has on perceptions of what constitutes a normal-sized food portion and measures of portion size selection. In studies 1 and 2 participants were visually exposed to images of large or small portions of spaghetti bolognese, before making evaluations about an image of an intermediate sized portion of the same food. In study ...

Evaluation of Pushback Decision-Support Tool Concept for Charlotte Douglas International Airport Ramp Operations

Science.gov (United States)

Hayashi, Miwa; Hoang, Ty; Jung, Yoon C.; Malik, Waqar; Lee, Hanbong; Dulchinos, Victoria L.

2015-01-01

This paper proposes a new departure pushback decision-support tool (DST) for airport ramp-tower controllers. It is based on NASA's Spot and Runway Departure Advisor (SARDA) collaborative decision-making concept, except with the modification that the gate releases now are controlled by tactical pushback (or gate-hold) advisories instead of strategic pre-assignments of target pushback times to individual departure flights. The proposed ramp DST relies on data exchange with the airport traffic control tower (ATCT) to coordinate pushbacks with the ATCT's flow-management intentions under current operational constraints, such as Traffic Management Initiative constraints. Airlines would benefit in reduced taxi delay and fuel burn. The concept was evaluated in a human-in-the-loop simulation experiment with current ramp-tower controllers at the Charlotte Douglas International Airport as participants. The results showed that the tool helped reduce taxi time by one minute per flight and overall departure flight fuel consumption by 10-12% without reducing runway throughput. Expect Departure Clearance Time (EDCT) conformance also was improved when advisories were provided. These benefits were attained without increasing the ramp-tower controllers' workload. Additionally, the advisories reduced the ATCT controllers' workload.

Local linear heat rate ramps in the WWER-440 transient regimes

International Nuclear Information System (INIS)

Brik, A.N.; Bibilashvili, Ju.L.; Bogatyr, S.M.; Medvedev, A.V.

1998-01-01

The operation of the WWER-440 reactors must be accomplished in such a way that the fuel rods durability would be high enough during the whole operation period. The important factors determining the absence of fuel rod failures are the criteria limiting the core characteristics (fuel rod and fuel assembly power, local linear heat rate, etc.). For the transient and load follow conditions the limitations on the permissible local linear rate ramp are also introduced. This limitation is the result of design limit of stress corrosion cracking of the fuel cladding and depends on the local fuel burn-up. The control rod motion is accompanied by power redistribution, which, in principle, can result in violating the design and operation limitations. Consequently, this motion have to be such as the core parameters, including the local ramps of the linear heat generation rates would not exceed the permissible ones.The paper considers the problem of WWER-440 reactor control under transient and load follow conditions and the associated optimisation of local linear heat generation rate ramps. The main factors affecting the solution of the problem under consideration are discussed. Some recommendations for a more optimal reactor operation are given.(Author)

Quantifying consumer portion control practices

DEFF Research Database (Denmark)

Spence, M.; Lähteenmäki, Liisa; Stancu, Violeta

2015-01-01

of Ireland. Three factors were extracted and named: measurement-strategy scale, eating-strategy scale, and purchasing-strategy scale. The eating-strategy scale score was the highest, while the measurement-strategy scale carried the lowest frequency score. For each strategy scale score, the strongest...... predictor was GHI, followed by gender. Having higher GHI and being female were independently associated with more frequent portion control. Both the eating-strategy scale score and the purchasing-strategy scale score were negatively associated with pizza portion size consumption estimates. In conclusion......, while this study demonstrates that the reported use of portion control practices is low, the findings provide preliminary evidence for their validity. Further studies are needed to explore how portion control practices are used in different kinds of portion size decisions and what their contribution...

Power ramping test in the JMTR for PCI study of water reactor fuel

International Nuclear Information System (INIS)

Nakata, H.; Kanbara, M.; Ichikawa, M.

1984-01-01

Power ramping test is essential for PCI study of water reactor fuel. Boiling water capsules have been used for the tests in the JMTR. Heat generation of fuel rod in the capsule can be changed by the He-3 power control facility during reactor operation. Four specially designed fuel rods have been ramped to about 41-43 kW/m; two of them have small gaps filled with iodine, the other two are equipped with centerline temperature thermocouple. Fuel rod elongation detector is equipped to each capsule. For the fuel rods with small gap, unique contraction followed by ordinary fuel relaxation behaviour was observed right after the fast ramping. None of them failed. Future programme includes a series of tests of fuel rods irradiated in the high-pressure water loop at the JMTR and a verification test of remedy fuel which allows daily-load-following operation of BWRs. (author)

IAEA specialists' meeting on power ramping and cycling behaviour of water reactor fuel. Summary report

Energy Technology Data Exchange (ETDEWEB)

NONE

1983-06-01

At its fourth Annual Meeting, the IAEA International Working Group on Water Reactor Fuel Performance and Technology (IWGFPT) recommended that the Agency should hold a second Specialists' Meeting on 'Power Ramping and Cycling Behaviour of Water Reactor Fuel'. As research activities related to power ramping and cycling of water reactor fuel have been pursued vigorously, it was the objective of this meeting to review and discuss today's State of the Art and current understanding of water reactor fuel behaviour related to this these. Emphasis should be on practical experience and experimental investigations. The meeting was organised in five sessions: Power ramping and power cycling programs in power and and research reactors; Experimental methods; Power ramping and cycling results; Investigations and results of separate effects, especially related to PCI, defect mechanism, mechanical response, fuel design, and specially related to fission gas release; Operational strategies, recommendations and economic implications. The session chairmen, together with the speakers, prepared and presented reports with summary, conclusions and recommendations of the individual sessions. These reports are added to this summary report.

IAEA specialists' meeting on power ramping and cycling behaviour of water reactor fuel. Summary report

International Nuclear Information System (INIS)

1983-06-01

At its fourth Annual Meeting, the IAEA International Working Group on Water Reactor Fuel Performance and Technology (IWGFPT) recommended that the Agency should hold a second Specialists' Meeting on 'Power Ramping and Cycling Behaviour of Water Reactor Fuel'. As research activities related to power ramping and cycling of water reactor fuel have been pursued vigorously, it was the objective of this meeting to review and discuss today's State of the Art and current understanding of water reactor fuel behaviour related to this these. Emphasis should be on practical experience and experimental investigations. The meeting was organised in five sessions: Power ramping and power cycling programs in power and and research reactors; Experimental methods; Power ramping and cycling results; Investigations and results of separate effects, especially related to PCI, defect mechanism, mechanical response, fuel design, and specially related to fission gas release; Operational strategies, recommendations and economic implications. The session chairmen, together with the speakers, prepared and presented reports with summary, conclusions and recommendations of the individual sessions. These reports are added to this summary report

Modified model of neutron resonance widths distribution. Results of total gamma-widths approximation

International Nuclear Information System (INIS)

Sukhovoj, A.M.; Khitrov, V.A.

2011-01-01

Functional dependences of probability to observe given Γ n 0 value and algorithms for determination of the most probable magnitudes of the modified model of resonance parameter distributions were used for analysis of the experimental data on the total radiative widths of neutron resonances. As in the case of neutron widths, precise description of the Γ γ spectra requires a superposition of three and more probability distributions for squares of the random normally distributed values with different nonzero average and nonunit dispersion. This result confirms the preliminary conclusion obtained earlier at analysis of Γ n 0 that practically in all 56 tested sets of total gamma widths there are several groups noticeably differing from each other by the structure of their wave functions. In addition, it was determined that radiative widths are much more sensitive than the neutron ones to resonance wave functions structure. Analysis of early obtained neutron reduced widths distribution parameters for 157 resonance sets in the mass region of nuclei 35 ≤ A ≤ 249 was also performed. It was shown that the experimental values of widths can correspond with high probability to superposition of several expected independent distributions with their nonzero mean values and nonunit dispersion

On Reynolds number dependence of micro-ramp-induced transition

NARCIS (Netherlands)

Ye, Q.; Schrijer, F.F.J.; Scarano, F.

2018-01-01

The variation of transitional flow features past a micro-ramp is investigated when the Reynolds number is decreased approaching the critical regime. Experiments are conducted in the incompressible flow spanning from supercritical to subcritical roughness-height-based Reynolds number ( , 730, 460

Truck acceleration behavior study and acceleration lane length recommendations for metered on-ramps

Directory of Open Access Journals (Sweden)

Guangchuan Yang

2016-10-01

Full Text Available This paper investigated the actual truck acceleration capability at metered on-ramps. Truck acceleration performance data were collected through a video-based data collection method. A piecewise constant acceleration model was employed to capture truck acceleration characteristics. It was found that the existing acceleration length will affect truck drivers’ acceleration behavior. At the taper type ramp that has limited acceleration distance, acceleration profile indicated a decreasing trend with distance. While for the ramp with an auxiliary lane that has sufficient acceleration distance, it was found that the acceleration behavior is to have a high acceleration rate in the beginning, then acceleration rate decrease with speed increase, and high acceleration rate again as drivers approach the merging area. Field data show that the truck acceleration performance data documented in the ITE’s (Institute of Transportation Engineers “Traffic Engineering Handbook” are much lower than the field collected data. Also, based on the regression analysis of speed versus distance profiles, it was found that the AASHTO’s (American Association of State Highway and Transportation Officials Green Book acceleration length design guidance is insufficient to accommodate trucks at metered on-ramps. The required acceleration lengths for medium and heavy trucks are approximately 1.3 and 1.6 times of the Green Book design guideline, respectively.

Effects of controlled element dynamics on human feedforward behavior in ramp-tracking tasks.

Science.gov (United States)

Laurense, Vincent A; Pool, Daan M; Damveld, Herman J; van Paassen, Marinus René M; Mulder, Max

2015-02-01

In real-life manual control tasks, human controllers are often required to follow a visible and predictable reference signal, enabling them to use feedforward control actions in conjunction with feedback actions that compensate for errors. Little is known about human control behavior in these situations. This paper investigates how humans adapt their feedforward control dynamics to the controlled element dynamics in a combined ramp-tracking and disturbance-rejection task. A human-in-the-loop experiment is performed with a pursuit display and vehicle-like controlled elements, ranging from a single integrator through second-order systems with a break frequency at either 3, 2, or 1 rad/s, to a double integrator. Because the potential benefits of feedforward control increase with steeper ramp segments in the target signal, three steepness levels are tested to investigate their possible effect on feedforward control with the various controlled elements. Analyses with four novel models of the operator, fitted to time-domain data, reveal feedforward control for all tested controlled elements and both (nonzero) tested levels of ramp steepness. For the range of controlled element dynamics investigated, it is found that humans adapt to these dynamics in their feedforward response, with a close to perfect inversion of the controlled element dynamics. No significant effects of ramp steepness on the feedforward model parameters are found.

Survey of the power ramp performance testing of KWU'S PWR UO 2, fuel

Science.gov (United States)

Ga¨rtner, M.; Fischer, G.

1987-06-01

To determine the power ramp performance of KWU's PWR UO 2 fuel, 134 fuel rodlets with burnups of up to 46 GWd/ t (U) and several fuel assemblies with 19 to 30 GWd/t (U) burnup were ramped in power in the research reactors HFR Petten/The Netherlands and R2 Studsvik/Sweden and in the power plants KWO and KWB-A/Germany, respectively. The power ramp tests demonstrate decreasing resistance of the PWR fuel rods to PCI (pellet-to-clad interaction) up to fuel burnups of 35 GWd/t (U) and a reversal effect at higher burnups. The fuel rods can be operated free of defects at fast power transients to linear heat generation rates of up to 400 W/cm, at least.Power levels of up to 490 W/cm can be reached without defects by reducing the ramp rate. After reshuffling according to an out-in scheme, 1-cycle fuel assemblies may return to rod powers of up to 480 W/cm with a power increase rate of up to 10 W/(cm min) without fuel rod damage. Set points basing on these test results and incorporated into the power distribution control and power density limitation system of KWU's advanced power plants guarantee safe plant operation under normal and load follow operating conditions.

Implementation Guideline for Maintenance Line Operations Safety Assessment (M-LOSA) and Ramp LOSA (R-LOSA) Programs

Science.gov (United States)

2012-08-01

Maintenance and/or Ramp LOSA)  Database  Observation protocol 16 hours; in person with hands-on observation and database practice 4. LOSA Database...Forms/Scenarios (Maintenance and/or Ramp LOSA)  Database  Observation protocol  Q&A Every year or every implementation run (whichever

Review of power ramp irradiations with different pellet L/D ratios and thicknesses of CANLUB layers

International Nuclear Information System (INIS)

2009-01-01

Power ramps in fuel during normal operation can result in Stress Corrosion Cracking (SCC) failures. Experimental evidence shows that pellets with smaller L/D ratios produce smaller circumferential ridges at pellet interface, the location where power ramps failures commonly occur. This may reduce the power ramp damage to the sheath, thereby improving the ability of the fuel sheath to withstand SCC. CANLUB coatings have demonstrated beneficial effects with respect to SCC. It is speculated that the coating acts as a chemical barrier by interacts with the corrosive fission products reducing the amount of corrosive species to reach susceptible areas of the sheath surface. This reduced concentration of corrosive products may enable the sheath to resist higher levels of incremental stresses/strains and therefore survive severe power-ramps. This work focuses on the review of experimental information that substantiates the effect of pellets with lower L/D ratios and thicker CANLUB layers on SCC sheath failures. (author)

Measurement and stabilization of the longitudinal and transversal tune on the fast energy ramp at ELSA

Energy Technology Data Exchange (ETDEWEB)

Eberhardt, Maren [Electron Stretcher Accelerator ELSA, Physikalisches Institut, Universitaet Bonn (Germany)

2008-07-01

At the electron stretcher accelerator ELSA, an external beam of unpolarized or polarized electrons is supplied to experimental set-ups. In order to correct for dynamic effects caused by eddy currents induced on the fast energy ramp, the accelerator tunes have to measured in situ with high precision. The measurements of betatron tunes during the fast energy ramp are based on the excitation of coherent betatron oscillations generated by a pulsed kicker magnet. The betatron frequency is determined by a Fourier analysis of the measured oscillations of the beam position. This technique was successfully applied to measure the horizontal tune on the fast energy ramp. During the fast energy ramp shifts of the betatron tune caused by eddy currents are induced. These tune shifts are measured and corrected when operating the accelerator with polarized beam. Measurements of coherent synchrotron oscillations will also be presented. These are excited by a phase modulation of the acceleration voltage using an electrical phase shifter in the reference RF signal path.

Power cycling and ramp test in R-2 and Mihama Unit 2 for MHI PWR fuels

International Nuclear Information System (INIS)

Baba, T.; Takahashi, T.; Kubo, H.; Fujiwara, Y.; Kondo, Y.

1983-01-01

Up to the present time, Mitsubishi has manufactured approximately 3000 fuel assemblies for Japanese PWRs, of which performance in reactors is satisfactory under base load operation. For the forthcoming load following age in Japan, expected in mid eighties, Mitsubishi is performing various R and D programs, so that load following operation can be smoothly introduced with current good performance maintained. R and D programs consist of two phases. One is the verification and demonstration of power ramping and cycling capability of the current design fuels, and the other is the development of remedy fuels with more operational margin. This paper describes the recent results obtained for the former phase, especially for the following two programs: (1) Power cycling and ramp test in R-2; (2) Power ramp demonstration (PRD) in Mihama Unit 2 (PRD-1). PIE works for power cycling and ramp test rods have been almost completed. The second PRD will be performed early in 1983

Arthroscopic all-inside ramp lesion repair using the posterolateral transseptal portal view.

Science.gov (United States)

Keyhani, Sohrab; Ahn, Jin Hwan; Verdonk, René; Soleymanha, Mehran; Abbasian, Mohammadreza

2017-02-01

The purpose of this study was to evaluate and describe the clinical results and outcomes of a novel method for all-inside suture repair of medial meniscus ramp lesions through posteromedial and posterolateral transseptal portals during anterior cruciate ligament (ACL) reconstruction. Further, this investigation compared the posterolateral view to the notch view for diagnosis and repair. Between 2011 and 2014, 166 patients had ramp lesions concomitantly with ACL injury; 128 patients (107 men and 21 women) were enrolled in the study after qualification. All patients underwent repair of the posterior horn ramp lesion of the medial meniscus, using a suture hook device with PDS No. 1 through a posteromedial portal while viewing from the posterolateral transseptal portal during ACL reconstruction, with a minimum of a 2-year follow-up. Patients were followed up for a minimum of 2 years (range 24-47 months). Their average Lysholm score increased from 61.7 ± 3.2 preoperatively to 87.8 ± 3.9 at last follow-up (p < 0.001). Moreover, their average IKDC scores also improved from 53.6 ± 2.1 (pre-op) to 82.1 ± 3.5 (at last follow-up) (p < 0.001). The peroneal nerve and the popliteal neurovascular bundle were not damaged in any of the patients. This study provides evidence that the posterolateral transseptal technique protects neurovascular structures. This technique may be used safely and easily for repair of the posterior horn ramp lesion of the medial meniscus during ACL reconstruction. IV.

Validation of a ramp running protocol for determination of the true VO2max in mice

Directory of Open Access Journals (Sweden)

Mohamed Ayachi

2016-08-01

Full Text Available In the field of comparative physiology, it remains to be established whether the concept of VO2max is valid in the mouse and, if so, how this value can be accurately determined. In humans, VO2max is generally considered to correspond to the plateau observed when VO2 no longer rises with an increase in workload. In contrast, the concept of VO2peak tends to be used in murine studies. The objectives of the present study were to determine whether (i a continuous ramp protocol yielded a higher VO2peak than a stepwise, incremental protocol, and (ii the VO2peak measured in the ramp protocol corresponded to VO2max. The three protocols (based on intensity-controlled treadmill running until exhaustion with eight female FVB/N mice were performed in random order: (a an incremental protocol that begins at 10 m.min-1 speed and increases by 3 m.min-1 every 3 min. (b a ramp protocol with slow acceleration (3 m.min-2, and (c a ramp protocol with fast acceleration (12 m.min-2. Each protocol was performed with two slopes (0° and 25°. Hence, each mouse performed six exercise tests. We found that the value of VO2peak was protocol-dependent (p 8 mmol.l-1 and a respiratory exchange ratio >1. The total duration of the 3 m.min-2 0° ramp protocol was shorter than that of the incremental protocol. Taken as a whole, our results suggest that VO2max in the mouse is best determined by applying a ramp exercise protocol with slow acceleration and no treadmill slope.

Portion size: a qualitative study of consumers' attitudes toward point-of-purchase interventions aimed at portion size.

Science.gov (United States)

Vermeer, Willemijn M; Steenhuis, Ingrid H M; Seidell, Jacob C

2010-02-01

This qualitative study assessed consumers' opinions of food portion sizes and their attitudes toward portion-size interventions located in various point-of-purchase settings targeting overweight and obese people. Eight semi-structured focus group discussions were conducted with 49 participants. Constructs from the diffusion of innovations theory were included in the interview guide. Each focus group was recorded and transcribed verbatim. Data were coded and analyzed with Atlas.ti 5.2 using the framework approach. Results showed that many participants thought that portion sizes of various products have increased during the past decades and are larger than acceptable. The majority also indicated that value for money is important when purchasing and that large portion sizes offer more value for money than small portion sizes. Furthermore, many experienced difficulties with self-regulating the consumption of large portion sizes. Among the portion-size interventions that were discussed, participants had most positive attitudes toward a larger availability of portion sizes and pricing strategies, followed by serving-size labeling. In general, reducing package serving sizes as an intervention strategy to control food intake met resistance. The study concludes that consumers consider interventions consisting of a larger variety of available portion sizes, pricing strategies and serving-size labeling as most acceptable to implement.

Key Performance Indicators for the Impact of Cognitive Assembly Planning on Ramp-Up Process

Directory of Open Access Journals (Sweden)

Christian Buescher

2012-01-01

Full Text Available Within the ramp-up phase of highly automated assembly systems, the planning effort forms a large part of production costs. Due to shortening product lifecycles, changing customer demands, and therefore an increasing number of ramp-up processes, these costs even rise. So assembly systems should reduce these efforts and simultaneously be flexible for quick adaption to changes in products and their variants. A cognitive interaction system in the field of assembly planning systems is developed within the Cluster of Excellence “Integrative production technology for high-wage countries” at RWTH Aachen University which integrates several cognitive capabilities according to human cognition. This approach combines the advantages of automation with the flexibility of humans. In this paper the main principles of the system's core component—the cognitive control unit—are presented to underline its advantages with respect to traditional assembly systems. Based on this, the actual innovation of this paper is the development of key performance indicators. These refer to the ramp-up process as a main objective of such a system is to minimize the planning effort during ramp-up. The KPIs are also designed to show the impact on the main idea of the Cluster of Excellence in resolving the so-called Polylemma of Production.

Turning behaviors of T cells climbing up ramp-like structures are regulated by myosin light chain kinase activity and lamellipodia formation.

Science.gov (United States)

Song, Kwang Hoon; Lee, Jaehyun; Jung, Hong-Ryul; Park, HyoungJun; Doh, Junsang

2017-09-14

T cells navigate diverse microenvironments to perform immune responses. Micro-scale topographical structures within the tissues, which may inherently exist in normal tissues or may be formed by inflammation or injury, can influence T cell migration, but how T cell migration is affected by such topographical structures have not been investigated. In this study, we fabricated ramp-like structures with a 5 μm height and various slopes, and observed T cells climbing up the ramp-like structures. T cells encountering the ramp-like structures exhibited MLC accumulation near head-tail junctions contacting the ramp-like structures, and made turns to the direction perpendicular to the ramp-like structures. Pharmacological study revealed that lamellipodia formation mediated by arp2/3 and contractility regulated by myosin light chain kinase (MLCK) were responsible for the intriguing turning behavior of T cells climbing the ramp-like structures. Arp2/3 or MLCK inhibition substantially reduced probability of T cells climbing sharp-edged ramp-like structures, indicating intriguing turning behavior of T cells mediated by lamellipodia formation and MLCK activity may be important for T cells to access inflamed or injured tissues with abrupt topographical changes.

Keeping Portions Under Control (For Parents)

Science.gov (United States)

... it possible to bring portion sizes back to earth? Yes. But first we have to understand how ... recommend for a portion of pasta, rice, cereal, vegetables, and fruit. A meat portion should be about ...

Modelling controlled VDE's and ramp-down scenarios in ITER

Science.gov (United States)

Lodestro, L. L.; Kolesnikov, R. A.; Meyer, W. H.; Pearlstein, L. D.; Humphreys, D. A.; Walker, M. L.

2011-10-01

Following the design reviews of recent years, the ITER poloidal-field coil-set design, including in-vessel coils (VS3), and the divertor configuration have settled down. The divertor and its material composition (the latter has not been finalized) affect the development of fiducial equilibria and scenarios together with the coils through constraints on strike-point locations and limits on the PF and control systems. Previously we have reported on our studies simulating controlled vertical events in ITER with the JCT 2001 controller to which we added a PID VS3 circuit. In this paper we report and compare controlled VDE results using an optimized integrated VS and shape controller in the updated configuration. We also present our recent simulations of alternate ramp-down scenarios, looking at the effects of ramp-down time and shape strategies, using these controllers. This work performed under the auspices of the U.S. Department of Energy by LLNL under Contract DE-AC52-07NA27344.

FEMAXI-7 analysis on behavior of medium and high burnup BWR fuels during base-irradiation and power ramp

Energy Technology Data Exchange (ETDEWEB)

Ogiyanagi, Jin, E-mail: ohgiyanagi.jin@jaea.go.jp [Japan Atomic Energy Agency, 2-4 Shirane, Shirakata, Tokai-mura, Naka-gun, Ibaraki 319-1195 (Japan); Hanawa, Satoshi; Suzuki, Motoe; Nagase, Fumihisa [Japan Atomic Energy Agency, 2-4 Shirane, Shirakata, Tokai-mura, Naka-gun, Ibaraki 319-1195 (Japan)

2012-12-15

Highlights: Black-Right-Pointing-Pointer Two power ramp experiments of BWR fuels were analyzed by FEMAXI-7 code. Black-Right-Pointing-Pointer Calculated FGR and cladding deformation showed reasonable agreement with PIE data. Black-Right-Pointing-Pointer High temperature FGR could be predicted by the enhanced Turnbull FG diffusion constant. Black-Right-Pointing-Pointer Local PCMI model in the code could reasonably predict cladding ridging deformation. - Abstract: Irradiation behavior of medium and high burnup BWR fuels during base-irradiation and subsequent power ramp test is analyzed by a fuel performance code FEMAXI-7. The code has a 1.5-D cylindrical geometry (4 axial segments) to have a coupled solution of thermal analysis and FEM mechanical analysis. Two kinds of target fuels are selected; one was subjected to a power ramp test in the DR3 reactor at RISO after the base-irradiation in a commercial BWR, and the other was subjected to the power ramp test in the DR3 reactor after the base-irradiation in the Halden boiling water reactor. The calculated values such as fission gas release after the base-irradiation and a cladding diameter profile before and after the ramp test show a reasonable agreement with measured data. In addition, the calculated ridging deformation of the cladding before and after the ramp test, which is obtained by using a local pellet-cladding mechanical interaction (PCMI) analysis geometry in FEMAXI-7, is compared with the measured data, and it is found that the FEMAXI-7 code is applicable to the local PCMI analysis of medium and high burnup rods under normal operation and power ramp conditions.

Off-bucket Proton Losses during Ramping

CERN Document Server

Catalan-Lasheras, N

1998-01-01

In this paper, we report a study undertaken to determine whether longitudinal and transverse amplitudes become coupled before the loss of the off-bucket protons during the ramp. We compute the synchro tron as well as the betatron tune changes with momentum and determine if synchro-betatron resonances blow-up the transverse particle amplitude. A strong coupling might allow a betatron cleaning of the se particles before they are outside the momentum acceptance of the machine. We show that this is not the case, justifying the need of momentum cleaning.

Simultaneous Provision of Flexible Ramping Product and Demand Relief by Interruptible Loads Considering Economic Incentives

Directory of Open Access Journals (Sweden)

Jiahua Hu

2017-12-01

Full Text Available To cope with the net load variability in real time, sufficient ramp capability from controllable resources is required. To address the issue of insufficient ramp capacity in real time operations, flexible ramping products (FRPs have been adopted by some Independent System Operators (ISOs in the USA as a new market design. The inherent variability and uncertainty caused by renewable energy sources (RESs call for new FRP providers apart from conventional generating units. The so-called interruptible load (IL has proved to be useful in maintaining the supply-demand balance by providing demand relief and can be a viable FRP provider in practice. Given this background, this work presents a stochastic real-time unit commitment model considering ramp requirement and simultaneous provision of IL for FRP and demand relief. Load serving entities (LSEs are included in the proposed model and act as mediators between the ISO and multiple ILs. In particular, incentive compatible contracts are designed to encourage customers to reveal their true outage costs. Case studies indicate both the system and LSEs can benefit by employing the proposed method and ILs can gain the highest profits by signing up a favorable contract.

Ischiofemoral space on MRI in an asymptomatic population: Normative width measurements and soft tissue signal variations

International Nuclear Information System (INIS)

Maras Oezdemir, Zeynep; Goermeli, Cemile Ayse; Sagir Kahraman, Ayseguel; Aydingoez, Uestuen

2015-01-01

To make normative width measurements of the ischiofemoral (IF) space in an asymptomatic population and to record soft tissue MRI signal variations within the IF space in order to determine whether such variations are associated with IF space dimensions. Normative width measurements of the IF space were prospectively made in 418 hips on 1.5 T MR images of 209 asymptomatic volunteers. Quantitative and qualitative assessments of the IF soft tissues including the quadratus femoris (QF) muscle were also made. The mean IF space width was 2.56 ± 0.75 cm (right, 2.60 ± 0.75 cm; left, 2.53 ± 0.75 cm). Soft tissue MRI signal abnormalities were present within the IF space in 19 (9.1 %) of 209 volunteers. Soft tissue abnormalities within the IF space included oedema (3/209, 1.4 %) of the QF and/or surrounding soft tissue, and only fatty infiltration (16/209, 7.7 %) of the QF. Bilateral IF spaces are asymmetrical in asymptomatic persons. There is ≥10 % of width difference between right and left IF spaces in approximately half of asymptomatic individuals. Fatty infiltration and oedema can be present at the IF space in a small portion of the asymptomatic population, who also have narrower IF spaces than those without soft tissue MRI signal abnormalities. (orig.)

Facies-controlled reservoir properties in ramp-fan and slope-apron deposits, Miocene Puente Formation, Los Angeles basin

Energy Technology Data Exchange (ETDEWEB)

Lyons, K.T.; Geving, R.L.; Suchecki, R.K.

1989-03-01

The Miocene Puente Formation in outcrops of the eastern Los Angeles basin is interpreted as a succession of slope-apron and ramp-fan deposits that accumulated in a prism-rise wedge. The principal depositional components of this dominantly base-of-slope and ramp system are ramp-fan channels and lobes, and slope-channel and slope-apron channel/interchannel deposits. Facies-specific textural, compositional, and diagenetic attributes observed in thin section assist in the classification of depositional facies. Specifically, occurrence of carbonate cement, clay mineralogy, and abundance of organic material vary as a function of component facies architecture of the depositional system. Slope and ramp-fan channel-fill sandstones are characterized by pervasive carbonate cements, including poikilotopic and fine-grained calcite, fine-grained and baroque dolomite, and minor siderite. Diagenetic clays predate carbonate cements, and dolomite predates coarser, void-filling calcite. Ramp-fan lobe and interchannel deposits are carbonate free but are rich in detrital clay and organic matter. Diagenetic clays include mixed-layer illite/smectite and kaolinite. Sediments deposited in slope-apron channel fill are virtually cement free except for small amounts of authigenic illite/smectite. Slope-apron interchannel deposits are characterized by high content of organic matter and clay-rich matrix. Potential reservoir characteristics, such as grain size, sorting, and abundance of depositional clay matrix, are related to the primary sedimentary properties of depositional architectural components in the ramp-fan and slope-apron system. Additional diagenetic modifications, without consideration of compaction, were controlled by precipitation reactions associated with fluid flow along pathways related to the depositional architectural framework.

PortionControl@HOME: Results of a Randomized Controlled Trial Evaluating the Effect of a Multi-Component Portion Size Intervention on Portion Control Behavior and Body Mass Index

NARCIS (Netherlands)

Poelman, M.P.; Vet, de E.; Velema, E.; Boer, de M.R.; Seidell, J.C.; Steenhuis, I.H.M.

2015-01-01

Background Food portion sizes influence energy intake. Purpose The purpose of this paper is to determine effectiveness of the “PortionControl@HOME” intervention on body mass index and portion control behavior. Methods A randomized controlled trial among 278 overweight and obese participants was

Test results of BM109 magnet field stability during ramping

International Nuclear Information System (INIS)

Kristalinski, A.

1992-12-01

This report presents results of the measured lag between the current ramp and the following magnetic field rise in BM109 magnets. The purpose of these tests is to choose identical ramping programs for PC4AN1, PC4AN2 and PC4AN3 magnets. The lag occurs due to the large eddy currents in the magnets' solid iron cores. The experiment requires a magnetic field stability of 0.1% during beam presence. Using existing equipment and a program slope of 100 Amp/sec starting at Tl yields fields within the 0.05% of set value. Add to this 0.05% for P.S. regulation to meet the required field stability of 0.1%. This program yields annual savings of $200,000 (assuming 100% usage) . Additional savings can be made by using faster slopes, but this requires additional controls

Key Performance Indicators for the Impact of Cognitive Assembly Planning on Ramp-Up Process

OpenAIRE

Buescher, Christian; Hauck, Eckart; Schilberg, Daniel; Jeschke, Sabina

2012-01-01

Within the ramp-up phase of highly automated assembly systems, the planning effort forms a large part of production costs. Due to shortening product lifecycles, changing customer demands, and therefore an increasing number of ramp-up processes, these costs even rise. So assembly systems should reduce these efforts and simultaneously be flexible for quick adaption to changes in products and their variants. A cognitive interaction system in the field of assembly planning systems is developed wi...

Micro-Ramp Flow Control for Oblique Shock Interactions: Comparisons of Computational and Experimental Data

Science.gov (United States)

Hirt, Stephanie M.; Reich, David B.; O'Connor, Michael B.

2012-01-01

Computational fluid dynamics was used to study the effectiveness of micro-ramp vortex generators to control oblique shock boundary layer interactions. Simulations were based on experiments previously conducted in the 15- by 15-cm supersonic wind tunnel at the NASA Glenn Research Center. Four micro-ramp geometries were tested at Mach 2.0 varying the height, chord length, and spanwise spacing between micro-ramps. The overall flow field was examined. Additionally, key parameters such as boundary-layer displacement thickness, momentum thickness and incompressible shape factor were also examined. The computational results predicted the effects of the microramps well, including the trends for the impact that the devices had on the shock boundary layer interaction. However, computing the shock boundary layer interaction itself proved to be problematic since the calculations predicted more pronounced adverse effects on the boundary layer due to the shock than were seen in the experiment.

An Improved Macro Model of Traffic Flow with the Consideration of Ramps and Numerical Tests

Directory of Open Access Journals (Sweden)

Zhongke Shi

2015-01-01

Full Text Available We present an improved macro model for traffic flow based on the existing models. The equilibrium point equation of the model is obtained. The stop-and-go traffic phenomenon is described in phase plane and the relationship between traffic jams and system instability is clearly shown in the phase plane diagrams. Using the improved model, some traffic phenomena on a highway with ramps are found in this paper. The numerical simulation is carried out to investigate various nonlinear traffic phenomena with a single ramp generated by different initial densities and vehicle generation rates. According to the actual road sections of Xi’an-Baoji highways, the situations of morning peak with several ramps are also analyzed. All these results are consistent with real traffic, which shows that the improved model is reasonable.

Flat-ramp vs. convex-concave thrust geometries in a deformable hanging wall: new insights from analogue modeling experiments

Science.gov (United States)

Almeida, Pedro; Tomas, Ricardo; Rosas, Filipe; Duarte, Joao; Terrinha, Pedro

2015-04-01

Different modes of strain accommodation affecting a deformable hanging-wall in a flat-ramp-flat thrust system were previously addressed through several (sandbox) analog modeling studies, focusing on the influence of different variables, such as: a) thrust ramp dip angle and friction (Bonini et al, 2000); b) prescribed thickness of the hanging-wall (Koy and Maillot, 2007); and c) sin-thrust erosion (compensating for topographic thrust edification, e.g. Persson and Sokoutis, 2002). In the present work we reproduce the same experimental procedure to investigate the influence of two different parameters on hanging-wall deformation: 1) the geometry of the thrusting surface; and 2) the absence of a velocity discontinuity (VD) that is always present in previous similar analogue modeling studies. Considering the first variable we use two end member ramp geometries, flat-ramp-flat and convex-concave, to understand the control exerted by the abrupt ramp edges in the hanging-wall stress-strain distribution, comparing the obtain results with the situation in which such edge singularities are absent (convex-concave thrust ramp). Considering the second investigated parameter, our motivation was the recognition that the VD found in the different analogue modeling settings simply does not exist in nature, despite the fact that it has a major influence on strain accommodation in the deformable hanging-wall. We thus eliminate such apparatus artifact from our models and compare the obtained results with the previous ones. Our preliminary results suggest that both investigated variables play a non-negligible role on the structural style characterizing the hanging-wall deformation of convergent tectonic settings were such thrust-ramp systems were recognized. Acknowledgments This work was sponsored by the Fundação para a Ciência e a Tecnologia (FCT) through project MODELINK EXPL/GEO-GEO/0714/2013. Pedro Almeida wants to thank to FCT for the Ph.D. grant (SFRH/BD/52556/2014) under the

Off ramp : a secondary school TDM program

Energy Technology Data Exchange (ETDEWEB)

Haq, F. [Better Environmentally Sound Transportation (BEST), Vancouver, BC (Canada)

2002-07-01

The cities of Vancouver and Victoria in British Columbia have implemented a high school vehicle trip reduction program entitled Off-Ramp. The program, created by BEST, is about youth empowerment to help youths lead their peers to walk, cycle, skateboard, in-line skate, or carpool to school for a sustainable environment. Students raise awareness through media and drama to counter pop images of driving as being cool. Sponsorship is very important to the success of the program.

Optimal bidding strategy for microgrids in joint energy and ancillary service markets considering flexible ramping products

International Nuclear Information System (INIS)

Wang, Jianxiao; Zhong, Haiwang; Tang, Wenyuan; Rajagopal, Ram; Xia, Qing; Kang, Chongqing; Wang, Yi

2017-01-01

Highlights: •Flexible ramping products are modelled in the framework of a microgrid. •Microgrids’ optimal bidding model is proposed in energy and ancillary service markets. •A hybrid stochastic and robust optimization approach is adopted. •The effectiveness of the proposed bidding model is verified based on real-world data. -- Abstract: Due to the volatile nature of wind and photovoltaic power, wind farms and solar stations are generally thought of as the consumers of ramping services. However, a microgrid (MG) is able to strategically integrate various distributed energy resources (DERs) to provide both energy and ancillary services (ASs) for the bulk power system. To evaluate the ramping capabilities of an MG in the joint energy and AS markets, an optimal bidding strategy is developed in this paper considering flexible ramping products (FRPs). By aggregating and coordinating various DERs, including wind turbines (WTs), photovoltaic systems (PVs), micro-turbines (MTs) and energy storage systems (ESSs), the MG is able to optimally allocate the capacities for energy, spinning reserve and ramping. Taking advantage of the synergy among DERs, the MG can maximize its revenues from different markets. Moreover, the flexibility of the MG for the bulk power system can be fully explored. To address the uncertainties introduced by renewable generation and market prices, a hybrid stochastic/robust optimization (RO) approach is adopted. Case studies based on a real-world MG with various DERs demonstrate the market behavior of the MG using the proposed bidding model.

6 Tips for Managing Portion Size

Science.gov (United States)

Eating healthy is about enjoying your food while also managing portion size. Most people eat and drink more than their bodies need especially when they are served larger portions. So, choosing smaller portions to begin with is important for maintaining your overall health and well-being.

Human Nav1.8: enhanced persistent and ramp currents contribute to distinct firing properties of human DRG neurons

Science.gov (United States)

Han, Chongyang; Estacion, Mark; Huang, Jianying; Vasylyev, Dymtro; Zhao, Peng; Dib-Hajj, Sulayman D.

2015-01-01

Although species-specific differences in ion channel properties are well-documented, little has been known about the properties of the human Nav1.8 channel, an important contributor to pain signaling. Here we show, using techniques that include voltage clamp, current clamp, and dynamic clamp in dorsal root ganglion (DRG) neurons, that human Nav1.8 channels display slower inactivation kinetics and produce larger persistent current and ramp current than previously reported in other species. DRG neurons expressing human Nav1.8 channels unexpectedly produce significantly longer-lasting action potentials, including action potentials with half-widths in some cells >10 ms, and increased firing frequency compared with the narrower and usually single action potentials generated by DRG neurons expressing rat Nav1.8 channels. We also show that native human DRG neurons recapitulate these properties of Nav1.8 current and the long-lasting action potentials. Together, our results demonstrate strikingly distinct properties of human Nav1.8, which contribute to the firing properties of human DRG neurons. PMID:25787950

Study on Trailing Edge Ramp of Supercritical Airfoil

Science.gov (United States)

2016-03-30

China Abstract Trailing edge flow control method could improve the performance of supercritical airfoil with a small modification on the original...stall behaviour . As a result, the non-separation ramp could increase the thickness of airfoil, which benefits wing structure and aerodynamic...direction based on the original RAE2822 airfoil, which will thicken the airfoil. The interpolation is implemented as shown in Eqn. 1. This modification could

EBR-II high-ramp transients under computer control

International Nuclear Information System (INIS)

Forrester, R.J.; Larson, H.A.; Christensen, L.J.; Booty, W.F.; Dean, E.M.

1983-01-01

During reactor run 122, EBR-II was subjected to 13 computer-controlled overpower transients at ramps of 4 MWt/s to qualify the facility and fuel for transient testing of LMFBR oxide fuels as part of the EBR-II operational-reliability-testing (ORT) program. A computer-controlled automatic control-rod drive system (ACRDS), designed by EBR-II personnel, permitted automatic control on demand power during the transients

Estimating the Probability of Wind Ramping Events: A Data-driven Approach

OpenAIRE

Wang, Cheng; Wei, Wei; Wang, Jianhui; Qiu, Feng

2016-01-01

This letter proposes a data-driven method for estimating the probability of wind ramping events without exploiting the exact probability distribution function (PDF) of wind power. Actual wind data validates the proposed method.

Prevention of the Portion Size Effect

NARCIS (Netherlands)

I. Versluis (Iris)

2016-01-01

markdownabstractAn increase in the portion size leads to an increase in energy intake, a phenomenon which is also referred to as the portion size effect. The increase in portion sizes in recent years is regarded as an important contributor to the increase in the prevalence of obesity. Hence, the aim

Reinforcement Learning for Ramp Control: An Analysis of Learning Parameters

Directory of Open Access Journals (Sweden)

Chao Lu

2016-08-01

Full Text Available Reinforcement Learning (RL has been proposed to deal with ramp control problems under dynamic traffic conditions; however, there is a lack of sufficient research on the behaviour and impacts of different learning parameters. This paper describes a ramp control agent based on the RL mechanism and thoroughly analyzed the influence of three learning parameters; namely, learning rate, discount rate and action selection parameter on the algorithm performance. Two indices for the learning speed and convergence stability were used to measure the algorithm performance, based on which a series of simulation-based experiments were designed and conducted by using a macroscopic traffic flow model. Simulation results showed that, compared with the discount rate, the learning rate and action selection parameter made more remarkable impacts on the algorithm performance. Based on the analysis, some suggestionsabout how to select suitable parameter values that can achieve a superior performance were provided.

Modelling of fission gas release in rods from the International DEMO-RAMP-II Project at Studsvik

International Nuclear Information System (INIS)

Malen, K.

1983-01-01

The DEMO-RAMP-II rods had a burn-up of 25-30 MWd/kg U. They were ramped to powers in the range 40-50 kW/m with hold times between 10 s and 4.5 minutes. In spite of the short hold times the fission gas release at the higher powers was more than 1%. With these short hold times it is natural to assume that mixing of released gas with plenum gas is limited. Modelling has been performed using GAPCONSV (a modified GAPCON-THERMAL-2) both with and without mixing of released gas with plenum gas. In particular for the high power-short duration ramps only the ''no mixing'' modelling yields release fractions comparable to the experimental values. (author)

Review of Wind Energy Forecasting Methods for Modeling Ramping Events

Energy Technology Data Exchange (ETDEWEB)

Wharton, S; Lundquist, J K; Marjanovic, N; Williams, J L; Rhodes, M; Chow, T K; Maxwell, R

2011-03-28

Tall onshore wind turbines, with hub heights between 80 m and 100 m, can extract large amounts of energy from the atmosphere since they generally encounter higher wind speeds, but they face challenges given the complexity of boundary layer flows. This complexity of the lowest layers of the atmosphere, where wind turbines reside, has made conventional modeling efforts less than ideal. To meet the nation's goal of increasing wind power into the U.S. electrical grid, the accuracy of wind power forecasts must be improved. In this report, the Lawrence Livermore National Laboratory, in collaboration with the University of Colorado at Boulder, University of California at Berkeley, and Colorado School of Mines, evaluates innovative approaches to forecasting sudden changes in wind speed or 'ramping events' at an onshore, multimegawatt wind farm. The forecast simulations are compared to observations of wind speed and direction from tall meteorological towers and a remote-sensing Sound Detection and Ranging (SODAR) instrument. Ramping events, i.e., sudden increases or decreases in wind speed and hence, power generated by a turbine, are especially problematic for wind farm operators. Sudden changes in wind speed or direction can lead to large power generation differences across a wind farm and are very difficult to predict with current forecasting tools. Here, we quantify the ability of three models, mesoscale WRF, WRF-LES, and PF.WRF, which vary in sophistication and required user expertise, to predict three ramping events at a North American wind farm.

Freeway Traffic Density and On-Ramp Queue Control via ILC Approach

Directory of Open Access Journals (Sweden)

Ronghu Chi

2014-01-01

Full Text Available A new queue length information fused iterative learning control approach (QLIF-ILC is presented for freeway traffic ramp metering to achieve a better performance by utilizing the error information of the on-ramp queue length. The QLIF-ILC consists of two parts, where the iterative feedforward part updates the control input signal by learning from the past control data in previous trials, and the current feedback part utilizes the tracking error of the current learning iteration to stabilize the controlled plant. These two parts are combined in a complementary manner to enhance the robustness of the proposed QLIF-ILC. A systematic approach is developed to analyze the convergence and robustness of the proposed learning scheme. The simulation results are further given to demonstrate the effectiveness of the proposed QLIF-ILC.

Determination of allowable ramp power levels to maintain the mechanical integrity for 14x14, 16x16 and 17x17 KOFAs

International Nuclear Information System (INIS)

Lee, Chan Bok; Kim, Ki Hang; Kim, Kyu Tae

1991-11-01

Transient behavior of the fuel rods with various rod power histories for 17x17 KOFA fuels has been calculated and evaluated, and sensitivity analyses of the key parameters such as rod power history before ramp, fast neutron flux and cycle length have also been performed. Results show that cladding strain is more limiting in determining the allowable ramp power level than fuel centerline temperature, and neutron flux has greatest influence on fuel transient behavior among rod power history before ramp, fast neutron flux and cycle length. Based upon the above results, allowable ramp power levels versus burnup for 14x14, 16x16 and 17x17 KOFA fuels were determined for the rods with different initial power levels of F xy = 0.6, 0.8, 1.0 and 1.2, which shows that the rod with lower initial power level gives lower allowable ramp power level. It can be said, therefore, that if the ramp power level of the rod at certain initial power level and burnup is less than the corresponding allowable ramp power level, the transient behavior of the rod satisfy the fuel rod design criteria. (Author)

Study of On-Ramp PI Controller Based on Dural Group QPSO with Different Well Centers Algorithm

Directory of Open Access Journals (Sweden)

Tao Wu

2015-01-01

Full Text Available A novel quantum-behaved particle swarm optimization (QPSO algorithm, dual-group QPSO with different well centers (DWC-QPSO algorithm, is proposed by constructing the master-slave subswarms. The new algorithm was applied in the parameter optimization of on-ramp traffic PI controller combining with nonlinear feedback theory. With the critical information contained in the searching space and results of the basic QPSO algorithm, this algorithm avoids the rapid disappearance of swarm diversity and enhances the global searching ability through collaboration between subswarms. Experiment results on an on-ramp traffic control simulation show that DWC-QPSO can be well applied in the study of on-ramp traffic PI controller and the comparison results illustrate that DWC-QPSO outperforms other evolutionary algorithms with enhancement in both adaptability and stability.

H-mode access during plasma current ramp-up in TCV

International Nuclear Information System (INIS)

Martin, Y.; Behn, R.; Furno, I.; Labit, B.; Reimerdes, H.

2014-01-01

A recent TCV experiment has investigated the dependence of the L–H transition threshold power on the plasma current ramp-rate and the X-point height above the divertor target, which both have previously been seen to affect the transition behaviour. Systematic scans in ohmically heated plasmas do not show any dependence on the plasma current ramp-up rate. In contrast, the threshold power is found to increase by a factor of two while the X-point is moved from about 10 cm up to 35 cm above the vessel floor. However, further increase, up to 60 cm, does not lead to any further increase of the required power. The Fundamenski et al model is tested against the measurements. Estimates of the Wagner number (Wa) at L–H transitions are generally close to unity, in accordance with the model. In contrast, estimates of Wa before the L–H transition, i.e. in L-mode, do not show the expected evolution towards unity. (paper)

Missing portion sizes in FFQ

DEFF Research Database (Denmark)

Køster-Rasmussen, Rasmus; Siersma, Volkert Dirk; Halldorson, Thorhallur I.

2015-01-01

-nearest neighbours (KNN) were compared with a reference based on self-reported portion sizes (quantified by a photographic food atlas embedded in the FFQ). Setting: The Danish Health Examination Survey 2007–2008. Subjects: The study included 3728 adults with complete portion size data. Results: Compared...

Human Na(v)1.8: enhanced persistent and ramp currents contribute to distinct firing properties of human DRG neurons.

Science.gov (United States)

Han, Chongyang; Estacion, Mark; Huang, Jianying; Vasylyev, Dymtro; Zhao, Peng; Dib-Hajj, Sulayman D; Waxman, Stephen G

2015-05-01

Although species-specific differences in ion channel properties are well-documented, little has been known about the properties of the human Nav1.8 channel, an important contributor to pain signaling. Here we show, using techniques that include voltage clamp, current clamp, and dynamic clamp in dorsal root ganglion (DRG) neurons, that human Na(v)1.8 channels display slower inactivation kinetics and produce larger persistent current and ramp current than previously reported in other species. DRG neurons expressing human Na(v)1.8 channels unexpectedly produce significantly longer-lasting action potentials, including action potentials with half-widths in some cells >10 ms, and increased firing frequency compared with the narrower and usually single action potentials generated by DRG neurons expressing rat Na(v)1.8 channels. We also show that native human DRG neurons recapitulate these properties of Na(v)1.8 current and the long-lasting action potentials. Together, our results demonstrate strikingly distinct properties of human Na(v)1.8, which contribute to the firing properties of human DRG neurons.

Width and partial widths of unstable particles in the light of the Nielsen identities

International Nuclear Information System (INIS)

Grassi, P.A.; Sirlin, A.; Kniehl, B.A.; Hamburg Univ.

2001-09-01

Fundamental properties of unstable particles, including mass, width, and partial widths, are examined on the basis of the Nielsen identities (NI) that describe the gauge dependence of Green functions. In particular, we prove that the pole residues and associated definitions of branching ratios and partial widths are gauge independent to all orders. A simpler, previously discussed definition of branching ratios and partial widths is found to be gauge independent through next-to-next-to-leading order. It is then explained how it may be modified in order to extend the gauge independence to all orders. We also show that the physical scattering amplitude is the most general combination of self-energy, vertex, and box contributions that is gauge independent for arbitrary s, discuss the analytical properties of the NI functions, and exhibit explicitly their one-loop expressions in the Z-γ sector of the Standard Model. (orig.)

Width and partial widths of unstable particles in the light of the Nielsen identities

International Nuclear Information System (INIS)

Grassi, Pietro A.; Kniehl, Bernd A.; Sirlin, Alberto

2002-01-01

Fundamental properties of unstable particles, including mass, width, and partial widths, are examined on the basis of the Nielsen identities (NI) that describe the gauge dependence of Green functions. In particular, we prove that the pole residues and associated definitions of branching ratios and partial widths are gauge independent to all orders. A simpler, previously discussed definition of branching ratios and partial widths is found to be gauge independent through next-to-next-to-leading order. It is then explained how it may be modified in order to extend the gauge independence to all orders. We also show that the physical scattering amplitude is the most general combination of self-energy, vertex, and box contributions that is gauge independent for arbitrary s, discuss the analytical properties of the NI functions, and exhibit explicitly their one-loop expressions in the Z-γ sector of the standard model

How does development lead time affect performance over the ramp-up lifecycle? : evidence from the consumer electronics industry

NARCIS (Netherlands)

Pufall, A.A.; Fransoo, J.C.; Jong, de A.; Kok, de A.G.

2012-01-01

In the fast-paced world of consumer electronics, short development lead times and efficient product ramp-ups are invaluable. The sooner and faster a firm can ramp-up production of a new product, the faster it can start to earn revenues, profit from early market opportunities, establish technology

40 CFR 1039.505 - How do I test engines using steady-state duty cycles, including ramped-modal testing?

Science.gov (United States)

2010-07-01

...-state duty cycles, including ramped-modal testing? 1039.505 Section 1039.505 Protection of Environment... duty cycles, including ramped-modal testing? This section describes how to test engines under steady-state conditions. In some cases, we allow you to choose the appropriate steady-state duty cycle for an...

Evaluations on power ramp data of PWR fuels by FROST and THERMOST codes

International Nuclear Information System (INIS)

Murai, K.; Ogawa, S.; Nuno, H.; Kondo, Y.

1987-01-01

An evaluation is presented of power ramp data of Mitsubishi's PWR fuel rods tested in R-2, Studsvik, which was analysed by FROST and THERMOST codes. The analyses give good predictions for measured diameter changes and on-power rod elongations. The work indicates that FROST is capable of analysing both radial and axial pellet-cladding mechanism interaction (PCMI) appropriately, and that predicted states of PCMI (i.e. stress and strain which cannot be measured directly) are considered to be reliable. The ramp data used in the present analyses were obtained in two joint programmes with five Japanese PWR utilities (KEPCO, KYEPCO, SEPCO, HEPCO, and JAPCO). (UK)

TRACC_PB SOSS Integrated Traffic Simulation for CLT Ramp Operation

Science.gov (United States)

Okuniek, Nikolai; Zhu, Zhifan

2017-01-01

This presentation provides the current task under the NASA-DLR research collaboration for airport surface. It presents the effort done to adapt TRACC and SOSS software components to simulate airport (CLT) ramp area traffic management using TRACC's conflict free taxi trajectory optimization and SOSS's fast time simulation platform.

Three dimensional experimental investigation of a hypersonic double-ramp flow

NARCIS (Netherlands)

Schrijer, F.F.J.; Caljouw, R.; Scarano, F.; Van Oudheusden, B.W.

The flow over a 15?-45? double compression ramp was studied at Mach 7.5. CFD computations are compared to 2 component PIV (particle image velocimetry) measurements. Furthermore stereoscopic PIV was used to measure the three component velocity vector, enabling to perform a 3D flow survey. The overall

Dynamic Pull-In Investigation of a Clamped-Clamped Nanoelectromechanical Beam under Ramp-Input Voltage and the Casimir Force

Directory of Open Access Journals (Sweden)

Amir R. Askari

2014-01-01

Full Text Available The influence of the Casimir excitation on dynamic pull-in instability of a nanoelectromechanical beam under ramp-input voltage is studied. The ramp-input actuation has applications in frequency sweeping of RF-N/MEMS. The presented model is nonlinear due to the inherent nonlinearity of electrostatics and the Casimir excitations as well as the geometric nonlinearity of midplane stretching. A Galerkin based reduced order modeling is utilized. It is found that the calculated dynamic pull-in ramp input voltage leads to dynamic pull-in step input voltage by increasing the slope of voltage-time diagram. This fact is utilized to verify the results of present study.

Enhancement of blurred image portions

NARCIS (Netherlands)

2008-01-01

This invention relates to a method for image enhancement, comprising a first step ( 41 ) of distinguishing blurred and non-blurred image portions of an input image, and a second step ( 42 ) of enhancing at least one of said blurred image portions of said input image to produce an output image. Said

ANALISA KEKUATAN KONSTRUKSI SIDE RAMP DOOR SISTEM STEEL WIRE ROPE PADA KM. DHARMA KENCANA II AKIBAT BEBAN STATIS DENGAN METODE ELEMEN HINGGA

Directory of Open Access Journals (Sweden)

Imam Pujo Mulyatno

2012-04-01

Full Text Available KM. DHARMA KENCANA II adalah kapal tipe Ro - Ro (Passanger Ship yang memiliki rute pelayaran Surabaya - Kumai - Semarang yang mampu mengangkut penumpang dan kendaraan dalam jumlah yang relatif banyak. Untuk memudahkan akses keluar masuk kendaraan yang akan diangkut, maka kapal ini dilengkapi dengan empat buah ramp door sistem steel wire rope, salah satunya adalah ramp door yang terletak dibagian kiri lambung kapal (side ramp door. Side ramp door akan menerima beban statis secara berulang - ulang sehingga dapat mengakibatkan deformasi, keretakan, kerusakan, dll. Penelitian tentang kekuatan konstruksi side ramp door perlu diperhatikan dan dilakukan dimana tegangan yang diakibatkan oleh beban yang mengenainya tidak boleh melebihi batas maksimum σyield bahan dan σijin berdasarkan rules dari klas, adapun acuan rules yang dipakai dalam penelitian ini adalah berdasarkan rules Biro Klasifikasi Indonesia. Analisa kekuatan konstruksi side ramp door dilakukan dengan menggunakan program berbasis FEM sedangkan untuk pemodelan dilakukan dengan menggunakan program berbasis CAD. Analisa yang digunakan adalah analisa beban statis untuk mengetahui karakteristik dan letak tegangan terbesar pada konstruksi side ramp door berdasarkan empat variasi pembebanan. Hasil analisa menggunakan program berbasis FEM didapatkan hasil maximum stress terbesar terjadi pada kondisi side ramp door dengan beban kendaraan truck yaitu sebesar 93,91 N/mm2 dimana daerah paling kritis terjadi pada node 22097 yang terletak pada gading nomor 8 bagian memanjang dan gading nomor 1 bagian melintang. Tegangan ini masih dalam kondisi aman karena setelah dibandingan dengan σyield bahan sebesar 400 N/mm2 dan σijin berdasarkan rules BKI sebesar 225,24 N/mm2 menghasilkan nilai safety factor sebesar 3,87 dan 2,18.

What determines product ramp-up performance? : a review of characteristics based on a case study at Nokia Mobile Phones

NARCIS (Netherlands)

Pufall, A.A.; Fransoo, J.C.; Kok, de A.G.

2007-01-01

We present a conceptual model to explore the essential characteristics that affect product ramp-up performance in the consumer electronics industry, specifically in the mobile phones sector. Our findings are based on data analysis within Nokia’s mobile phones business group. Fast product ramp-ups

GAP WIDTH STUDY IN LASER BUTT-WELDING

DEFF Research Database (Denmark)

Gong, Hui; Olsen, Flemming Ove

power : 2 and 2.6 kW and the focal point position : 0 and -1.2 mm. Quality of all the butt welds are destructively tested according to ISO 13919-1.Influences of the variable process parameters to the maximum allowable gap width are observed as (1) the maximum gap width is inversely related......In this paper the maximum allowable gap width in laser butt-welding is intensively studied. The gap width study (GWS) is performed on the material of SST of W1.4401 (AISI 316) under various welding conditions, which are the gap width : 0.00-0.50 mm, the welding speed : 0.5-2.0 m/min, the laser...... to the welding speed, (2) the larger laser power leads to the bigger maximum allowable gap width and (3) the focal point position has very little influence on the maximum gap width....

Japanese programme on the development of high duty fuel and related power ramping tests

International Nuclear Information System (INIS)

Mishima, Y.

1983-01-01

Power ramping tests hitherto planned or carried out in Japan can be classified into two categories: 1) the tests programme by private organizations on fuel behaviour under various conditions of power ramping, in participating international programmes; and 2) a partially government sponsored programme, which was officially inaugurated in 1981 under the title of High-Duty Fuel Development Programme. The latter has been carried out by the Nuclear Power Engineering Test Centre, based on the schedule decided by the MITI Committee (chaired by the author), for a period of 10 years. These programmes will be described with emphasis on the latter (National Programme). (author)

Variations in detachment levels, ramp angles and wedge geometries along the Alberta thrust front

Energy Technology Data Exchange (ETDEWEB)

Spratt, D. A.; Lawton, D. C. [Calgary Univ., AB (Canada). Dept. of Geology and Geophysics

1996-06-01

In addition to the three stratigraphic horizons previously described by other investigators, six extensive Upper Cretaceous detachment horizons have been identified by detailed mapping, interpretation of high-resolution seismic data and regional correlation. Of the 984 ramp angles measured, the majority were found to fall between 10 degrees and 30 degrees. Ramp angles tended to decrease from north to south. This tendency was attributed to the thick sequence (2500 m) of competent rock involved in the deformation at Grande Cache, and the presence of multiple detachments and many thinner thrust sheets (100-500 m) in southern Alberta. 38 refs., 12 figs.

Japanese programme on the development of high duty fuel and related power ramping tests

Energy Technology Data Exchange (ETDEWEB)

Mishima, Y

1983-06-01

Power ramping tests hitherto planned or carried out in Japan can be classified into two categories: 1) the tests programme by private organizations on fuel behaviour under various conditions of power ramping, in participating international programmes; and 2) a partially government sponsored programme, which was officially inaugurated in 1981 under the title of High-Duty Fuel Development Programme. The latter has been carried out by the Nuclear Power Engineering Test Centre, based on the schedule decided by the MITI Committee (chaired by the author), for a period of 10 years. These programmes will be described with emphasis on the latter (National Programme). (author)

STEREO Observations of Waves in the Ramp Regions of Interplanetary Shocks

Science.gov (United States)

Cohen, Z.; Breneman, A. W.; Cattell, C. A.; Davis, L.; Grul, P.; Kersten, K.; Wilson, L. B., III

2017-12-01

Determining the role of plasma waves in providing energy dissipation at shock waves is of long-standing interest. Interplanetary (IP) shocks serve as a large database of low Mach number shocks. We examine electric field waveforms captured by the Time Domain Sampler (TDS) on the STEREO spacecraft during the ramps of IP shocks, with emphasis on captures lasting 2.1 seconds. Previous work has used captures of shorter duration (66 and 131 ms on STEREO, and 17 ms on WIND), which allowed for observation of waves with maximum (minimum) frequencies of 125 kHz (15 Hz), 62.5 kHz (8 Hz), and 60 kHz (59 Hz), respectively. The maximum frequencies are comparable to 2-8 times the plasma frequency in the solar wind, enabling observation of Langmuir waves, ion acoustic, and some whistler-mode waves. The 2 second captures resolve lower frequencies ( few Hz), which allows us to analyze packet structure of the whistler-mode waves and some ion acoustic waves. The longer capture time also improves the resolvability of simultaneous wave modes and of waves with frequencies on the order of 10s of Hz. Langmuir waves, however, cannot be identified at this sampling rate, since the plasma frequency is usually higher than 3.9 kHz. IP shocks are identified from multiple databases (Helsinki heliospheric shock database at http://ipshocks.fi, and the STEREO level 3 shock database at ftp://stereoftp.nascom.nasa.gov/pub/ins_data/impact/level3/). Our analysis focuses on TDS captures in shock ramp regions, with ramp durations determined from magnetic field data taken at 8 Hz. Software is used to identify multiple wave modes in any given capture and classify waves as Langmuir, ion acoustic, whistler, lower hybrid, electron cyclotron drift instability, or electrostatic solitary waves. Relevant frequencies are determined from density and magnetic field data collected in situ. Preliminary results suggest that large amplitude (≥ 5 mV/m) ion acoustic waves are most prevalent in the ramp, in agreement with

Comparison of known food weights with image-based portion-size automated estimation and adolescents' self-reported portion size.

Science.gov (United States)

Lee, Christina D; Chae, Junghoon; Schap, TusaRebecca E; Kerr, Deborah A; Delp, Edward J; Ebert, David S; Boushey, Carol J

2012-03-01

Diet is a critical element of diabetes self-management. An emerging area of research is the use of images for dietary records using mobile telephones with embedded cameras. These tools are being designed to reduce user burden and to improve accuracy of portion-size estimation through automation. The objectives of this study were to (1) assess the error of automatically determined portion weights compared to known portion weights of foods and (2) to compare the error between automation and human. Adolescents (n = 15) captured images of their eating occasions over a 24 h period. All foods and beverages served were weighed. Adolescents self-reported portion sizes for one meal. Image analysis was used to estimate portion weights. Data analysis compared known weights, automated weights, and self-reported portions. For the 19 foods, the mean ratio of automated weight estimate to known weight ranged from 0.89 to 4.61, and 9 foods were within 0.80 to 1.20. The largest error was for lettuce and the most accurate was strawberry jam. The children were fairly accurate with portion estimates for two foods (sausage links, toast) using one type of estimation aid and two foods (sausage links, scrambled eggs) using another aid. The automated method was fairly accurate for two foods (sausage links, jam); however, the 95% confidence intervals for the automated estimates were consistently narrower than human estimates. The ability of humans to estimate portion sizes of foods remains a problem and a perceived burden. Errors in automated portion-size estimation can be systematically addressed while minimizing the burden on people. Future applications that take over the burden of these processes may translate to better diabetes self-management. © 2012 Diabetes Technology Society.

Assessment of the prediction capability of the TRANSURANUS fuel performance code on the basis of power ramp tested LWR fuel rods

International Nuclear Information System (INIS)

Pastore, G.; Botazzoli, P.; Di Marcello, V.; Luzzi, L.

2009-01-01

The present work is aimed at assessing the prediction capability of the TRANSURANUS code for the performance analysis of LWR fuel rods under power ramp conditions. The analysis refers to all the power ramp tested fuel rods belonging to the Studsvik PWR Super-Ramp and BWR Inter-Ramp Irradiation Projects, and is focused on some integral quantities (i.e., burn-up, fission gas release, cladding creep-down and failure due to pellet cladding interaction) through a systematic comparison between the code predictions and the experimental data. To this end, a suitable setup of the code is established on the basis of previous works. Besides, with reference to literature indications, a sensitivity study is carried out, which considers the 'ITU model' for fission gas burst release and modifications in the treatment of the fuel solid swelling and the cladding stress corrosion cracking. The performed analyses allow to individuate some issues, which could be useful for the future development of the code. Keywords: Light Water Reactors, Fuel Rod Performance, Power Ramps, Fission Gas Burst Release, Fuel Swelling, Pellet Cladding Interaction, Stress Corrosion Cracking

Validity of Thermal Ramping Assays Used to Assess Thermal Tolerance in Arthropods

DEFF Research Database (Denmark)

Overgaard, Johannes; Kristensen, Torsten Nygård; Sørensen, Jesper Givskov

2012-01-01

are useful assays for small insects because they incorporate an ecologically relevant gradual temperature change. However, recent model-based papers have suggested that estimates of thermal resistance may be strongly confounded by simultaneous starvation and dehydration stress. In the present study we...... empirically test these model predictions using two sets of independent experiments. We clearly demonstrate that results from ramping assays of small insects (Drosophila melanogaster) are not compromised by starvation- or dehydration-stress. Firstly we show that the mild disturbance of water and energy balance...... of D. melanogaster experienced during the ramping tests does not confound heat tolerance estimates. Secondly we show that flies pre-exposed to starvation and dehydration have ‘‘normal’’ heat tolerance and that resistance to heat stress is independent of the energetic and water status of the flies...

A deterministic width function model

Directory of Open Access Journals (Sweden)

C. E. Puente

2003-01-01

Full Text Available Use of a deterministic fractal-multifractal (FM geometric method to model width functions of natural river networks, as derived distributions of simple multifractal measures via fractal interpolating functions, is reported. It is first demonstrated that the FM procedure may be used to simulate natural width functions, preserving their most relevant features like their overall shape and texture and their observed power-law scaling on their power spectra. It is then shown, via two natural river networks (Racoon and Brushy creeks in the United States, that the FM approach may also be used to closely approximate existing width functions.

Controls on facies and sequence stratigraphy of an upper Miocene carbonate ramp and platform, Melilla basin, NE Morocco

Science.gov (United States)

Cunningham, K.J.; Collins, Luke S.

2002-01-01

Upwelling of cool seawater, paleoceanographic circulation, paleoclimate, local tectonics and relative sea-level change controlled the lithofacies and sequence stratigraphy of a carbonate ramp and overlying platform that are part of a temporally well constrained carbonate complex in the Melilla basin, northeastern Morocco. At Melilla, from oldest to youngest, a third-order depositional sequence within the carbonate complex contains (1) a retrogradational, transgressive, warm temperate-type rhodalgal ramp; (2) an early highstand, progradational, bioclastic platform composed mainly of a temperate-type, bivalve-rich molechfor facies; and (3) late highstand, progradational to downstepping, subtropical/tropical-type chlorozoan fringing Porites reefs. The change from rhodalgal ramp to molechfor platform occurred at 7.0??0.14 Ma near the Tortonian/Messinian boundary. During a late stage in the development of the bioclastic platform a transition from temperate-type molechfor facies to subtropical/tropical-type chlorozoan facies occurred and is bracketed by chron 3An.2n (??? 6.3-6.6 Ma). Comparison to a well-dated carbonate complex in southeastern Spain at Cabo de Gata suggests that upwelling of cool seawater influenced production of temperate-type limestone within the ramp and platform at Melilla during postulated late Tortonian-early Messinian subtropical/tropical paleoclimatic conditions in the western Paleo-Mediterranean region. The upwelling of cool seawater across the bioclastic platform at Melilla could be related to the beginning of 'siphoning' of deep, cold Atlantic waters into the Paleo-Mediterranean Sea at 7.17 Ma. The facies change within the bioclastic platform from molechfor to chlorozoan facies may be coincident with a reduction of the siphoning of Atlantic waters and the end of upwelling at Melilla during chron 3An.2n. The ramp contains one retrogradational parasequence and the bioclastic platform three progradational parasequences. Minor erosional surfaces

Assessment of peak oxygen uptake during handcycling: Test-retest reliability and comparison of a ramp-incremented and perceptually-regulated exercise test.

Science.gov (United States)

Hutchinson, Michael J; Paulson, Thomas A W; Eston, Roger; Goosey-Tolfrey, Victoria L

2017-01-01

To examine the reliability of a perceptually-regulated maximal exercise test (PRETmax) to measure peak oxygen uptake ([Formula: see text]) during handcycle exercise and to compare peak responses to those derived from a ramp-incremented protocol (RAMP). Twenty recreationally active individuals (14 male, 6 female) completed four trials across a 2-week period, using a randomised, counterbalanced design. Participants completed two RAMP protocols (20 W·min-1) in week 1, followed by two PRETmax in week 2, or vice versa. The PRETmax comprised five, 2-min stages clamped at Ratings of Perceived Exertion (RPE) 11, 13, 15, 17 and 20. Participants changed power output (PO) as often as required to maintain target RPE. Gas exchange variables (oxygen uptake, carbon dioxide production, minute ventilation), heart rate (HR) and PO were collected throughout. Differentiated RPE were collected at the end of each stage throughout trials. For relative [Formula: see text], coefficient of variation (CV) was equal to 4.1% and 4.8%, with ICC(3,1) of 0.92 and 0.85 for repeated measures from PRETmax and RAMP, respectively. Measurement error was 0.15 L·min-1 and 2.11 ml·kg-1·min-1 in PRETmax and 0.16 L·min-1 and 2.29 ml·kg-1·min-1 during RAMP for determining absolute and relative [Formula: see text], respectively. The difference in [Formula: see text] between PRETmax and RAMP was tending towards statistical significance (26.2 ± 5.1 versus 24.3 ± 4.0 ml·kg-1·min-1, P = 0.055). The 95% LoA were -1.9 ± 4.1 (-9.9 to 6.2) ml·kg-1·min-1. The PRETmax can be used as a reliable test to measure [Formula: see text] during handcycle exercise in recreationally active participants. Whilst PRETmax tended towards significantly greater [Formula: see text] values than RAMP, the difference is smaller than measurement error of determining [Formula: see text] from PRETmax and RAMP.

The effects of lane width, shoulder width, and road cross-sectional reallocation on drivers' behavioral adaptations.

Science.gov (United States)

Mecheri, Sami; Rosey, Florence; Lobjois, Régis

2017-07-01

Previous research has shown that lane-width reduction makes drivers operate vehicles closer to the center of the road whereas hard-shoulder widening induces a position farther away from the road's center. The goal of the present driving-simulator study was twofold. First, it was aimed at further investigating the respective effects of lane and shoulder width on in-lane positioning strategies, by examining vehicle distance from the center of the lane. The second aim was to assess the impact on safety of three possible cross-sectional reallocations of the width of the road (i.e., three lane-width reductions with concomitant shoulder widening at a fixed cross-sectional width) as compared to a control road. The results confirmed that lane-width reduction made participants drive closer to the road's center. However, in-lane position was affected differently by lane narrowing, depending on the traffic situation. In the absence of oncoming traffic, lane narrowing gave rise to significant shifts in the car's distance from the lane's center toward the edge line, whereas this distance remained similar across lane widths during traffic periods. When the shoulders were at least 0.50m wide, participants drove farther away from both the road center and the lane center. Road reallocation operations resulted in vehicles positioned farther away from the edge of the road and less swerving behavior, without generating higher driving speeds. Finally, it is argued that road-space reallocation may serve as a good low-cost tool for providing a recovery area for steering errors, without impairing drivers' behavior. Copyright © 2017 Elsevier Ltd. All rights reserved.

Power ramp rate capabilities of a 5 kW proton exchange membrane fuel cell system with discrete ejector control

Science.gov (United States)

Nikiforow, K.; Pennanen, J.; Ihonen, J.; Uski, S.; Koski, P.

2018-03-01

The power ramp rate capabilities of a 5 kW proton exchange membrane fuel cell (PEMFC) system are studied theoretically and experimentally for grid support service applications. The fuel supply is implemented with a fixed-geometry ejector and a discrete control solution without any anode-side pressure fluctuation suppression methods. We show that the stack power can be ramped up from 2.0 kW to 4.0 kW with adequate fuel supply and low anode pressure fluctuations within only 0.1 s. The air supply is implemented with a centrifugal blower. Air supply ramp rates are studied with a power increase executed within 1 and 0.2 s after the request, the time dictated by grid support service requirements in Finland and the UK. We show that a power ramp-up from 2.0 kW to 3.7 kW is achieved within 1 s with an initial air stoichiometry of 2.5 and within 0.2 s with an initial air stoichiometry of 7.0. We also show that the timing of the power ramp-up affects the achieved ancillary power capacity. This work demonstrates that hydrogen fueled and ejector-based PEMFC systems can provide a significant amount of power in less than 1 s and provide valuable ancillary power capacity for grid support services.

Probabilistic Analysis of Crack Width

Directory of Open Access Journals (Sweden)

J. Marková

2000-01-01

Full Text Available Probabilistic analysis of crack width of a reinforced concrete element is based on the formulas accepted in Eurocode 2 and European Model Code 90. Obtained values of reliability index b seem to be satisfactory for the reinforced concrete slab that fulfils requirements for the crack width specified in Eurocode 2. However, the reliability of the slab seems to be insufficient when the European Model Code 90 is considered; reliability index is less than recommended value 1.5 for serviceability limit states indicated in Eurocode 1. Analysis of sensitivity factors of basic variables enables to find out variables significantly affecting the total crack width.

Fuel cladding mechanical interaction during power ramps

International Nuclear Information System (INIS)

Guerin, Y.

1985-01-01

Mechanical interaction between fuel and cladding may occur as a consequence of two types of phenomenon: i) fuel swelling especially at levels of caesium accumulation, and ii) thermal differential expansion during power changes. Slow overpower ramps which may occur during incidental events are of course one of the circumstances responsible for this second type of fuel cladding mechanical interaction (FCMI). Experiments and analysis of this problem that have been done at C.E.A. allow to determine the main parameters which will fix the level of stress and the risk of damage induced by the fuel in the cladding during overpower transients

Predictive Control of Wind Turbine for Load Reduction during Ramping Events

DEFF Research Database (Denmark)

Liu, Weipeng; Li, Changgang; Liu, Yutian

2017-01-01

on the Blade Element Momentum (BEM) theory. The generator speed and pitch angle are simultaneously regulated to realize the control objectives. A two-stage optimization is designed in order to reduce the computational complexity. The objectives of the first stage are minimizing the ramping rate and maximizing...

Influence of Slip Condition on Unsteady Free Convection Flow of Viscous Fluid with Ramped Wall Temperature

Directory of Open Access Journals (Sweden)

Sami Ul Haq

2015-01-01

Full Text Available The objective of this study is to explore the influence of wall slip condition on a free convection flow of an incompressible viscous fluid with heat transfer and ramped wall temperature. Exact solution of the problem is obtained by using Laplace transform technique. Graphical results to see the effects of Prandtl number Pr, time t, and slip parameter η on velocity and skin friction for the case of ramped and constant temperature of the plate are provided and discussed.

Elastic-Plastic Behavior of U6Nb under Ramp Wave Loading

International Nuclear Information System (INIS)

Hayes, D. B.; Gray, G. T. III; Hixson, R. S.; Hall, C. A.

2006-01-01

When uranium-niobium (6 wt.%) alloy is shock loaded, the expected elastic precursor is absent. A prior model attributed this absence to shear-induced twinning and the concomitant shear stress reduction that prevented the shocked material from reaching the plastic yield point. In the present study, carefully prepared U6Nb was subjected to shock loading to verify the adequacy of the prior model. Other samples were loaded with a ramp pressure pulse with strain rate large enough so that significant twinning would not occur during the experiment. Backward integration analyses of these latter experiments' back surface motion give stress-strain loading paths in U6Nb that suggest ordinary elastic-plastic flow. Some of the U6Nb was pre-strained by cold rolling in an effort to further ensure that twinning did not affect wave propagation. Shock and ramp loadings yielded similar results to the baseline material except, as expected, they are consistent with a higher yield stress and twinning shear stress threshold

Investigation of WWER fuel behaviour under MIR power ramps

International Nuclear Information System (INIS)

Bibilashvili, Yu.K.; Novikov, V.V.; Agafonov, S.N.

1996-01-01

The paper discusses results of experimental WWER fuel investigation under power ramps. Specificity of using the research reactor ''MIR'' to accomplish scheduled power rating of fuel is considered. The paper presents the methodology of experiments using irradiation facility ''TEST''. Reactor experiments were performed at burn-up ∼ 10000 MW.day/t UO 2 using standard fuel pins and the ones having backfitted fuel and cladding. (author). 7 figs, 1 tab

Lower hybrid wave current ramp-up and plasma equilibrium

International Nuclear Information System (INIS)

Gong Xueyu

1996-01-01

Questions on lower hybrid driven current and plasma equilibrium are studied. With the induced electric field taken into account, a system of self-consistent equations is obtained. This theory has been applied to some moments of the current ramp-up phase for the Tokamak Engineering Test Breeder (TETB) to study the lower hybrid current drive and MHD equilibrium. So, better electron current and safety factor profiles are obtained

Critical heat flux phenomena in flow boiling during step wise and ramp wise power transients

International Nuclear Information System (INIS)

Celata, G.P.; Cumo, M.; D'Annibale, F.; Farello, G.E.; Abou Said, S.

1987-01-01

The present paper deals with the results of an experimental investigation of the forced flow critical heat flux during power transients in a vertically heated channel. Experiments were carried out with a Refrigerant-12 1oop employing a circular test section which was electrically and uniformly heated. The power transients were performed with the step-wise and ramp-wise increase of the power to the test section. The test parameters included several values of the initial power (before the transient) and the final power (at the end of the transient) in the case of step-wise transients and the slope of the ramp in the case of ramp-wise transients. The pressure and specific mass flow rate, which were kept constant during the power transient,were varied from 1.2 to 2.7 MPa and 850 to 1500 Kg/sm 2 , respectively. Correlations of the experimental data for the time-to-crisis in terms of the independent parameters of the system are also proposed and verified for different values of pressure,mass flow rate, and inlet subcooling

Recycling silicon wire-saw slurries: separation of silicon and silicon carbide in a ramp settling tank under an applied electrical field.

Science.gov (United States)

Tsai, Tzu-Hsuan; Shih, Yu-Pei; Wu, Yung-Fu

2013-05-01

The growing demand for silicon solar cells in the global market has greatly increased the amount of silicon sawing waste produced each year. Recycling kerf Si and SiC from sawing waste is an economical method to reduce this waste. This study reports the separation of Si and SiC using a ramp settling tank. As they settle in an electrical field, small Si particles with higher negative charges have a longer horizontal displacement than SiC particles in a solution of pH 7, resulting in the separation of Si and SiC. The agreement between experimental results and predicted results shows that the particles traveled a short distance to reach the collection port in the ramp tank. Consequently, the time required for tiny particles to hit the tank bottom decreased, and the interference caused by the dispersion between particles and the fluid motion during settling decreased. In the ramp tank, the highest purities of the collected SiC and Si powders were 95.2 and 7.01 wt%, respectively. Using a ramp tank, the recycling fraction of Si-rich powders (SiC tanks. Recycling Si and SiC abrasives from the silicon sawing waste is regarded as an economical solution to reduce the sawing waste. However, the separation of Si and SiC is difficult. This study reports the separation of Si and SiC using a ramp settling tank under an applied electrical field. As they settle in an electrical field, small Si particles with higher negative charges have a longer horizontal displacement than SiC particles in a solution of pH 7, resulting in the separation of Si and SiC. Compared with the rectangular tanks, the recycling fraction of Si-rich powders using a ramp tank is greater, and the proposed ramp settling tank is more suitable for industrial applications.

A RAMP marker linked to the tobacco black shank resistant gene ...

African Journals Online (AJOL)

Bulk segregant analysis (BSA) and randomly amplified microsatellite polymorphism (RAMP) were employed to analyze F2 individuals of the Yunyan 317×Hubei 517 to screen and characterize molecular markers linked to black shank resistant gene. A total of 800 arbitrary decamer oligonucleotide primerpairs were used for ...

Calculations of Fission Gas Release During Ramp Tests Using Copernic Code

Energy Technology Data Exchange (ETDEWEB)

Tong, Liu [Nuclear Fuel R and D Center, China Nuclear Power Technology Research Institute (CNPRI) (China)

2013-03-15

The report performed under IAEA research contract No.15951 describes the results of fuel performance evaluation of LWR fuel rods operated at ramp conditions using the COPERNIC code developed by AREVA. The experimental data from the Third Riso Fission Gas Project and the Studsvik SUPER-RAMP Project presented in the IFPE database of the OECD/NEA has been utilized for assessing the code itself during simulation of fission gas release (FGR). Standard code models for LWR fuel were used in simulations with parameters set properly in accordance with relevant test reports. With the help of data adjustment, the input power histories are restructured to fit the real ones, so as to ensure the validity of FGR prediction. The results obtained by COPERNIC show that different models lead to diverse predictions and discrepancies. By comparison, the COPERNIC V2.2 model (95% Upper bound) is selected as the standard FGR model in this report and the FGR phenomenon is properly simulated by the code. To interpret the large discrepancies of some certain PK rods, the burst effect of FGR which is taken into consideration in COPERNIC is described and the influence of the input power histories is extrapolated. In addition, the real-time tracking capability of COPERNIC is tested against experimental data. In the process of investigation, two main dominant factors influencing the measured gas release rate are described and different mechanisms are analyzed. With the limited predicting capacity, accurate predictions cannot be carried out on abrupt changes of FGR during ramp tests by COPERNIC and improvements may be necessary to some relevant models. (author)

Properties of Phase Transition of Traffic Flow on Urban Expressway Systems with Ramps and Accessory Roads

International Nuclear Information System (INIS)

Mei Chaoqun; Liu Yejin

2011-01-01

In this paper, we develop a cellular automaton model to describe the phase transition of traffic flow on urban expressway systems with on-off-ramps and accessory roads. The lane changing rules are given in detailed, the numerical results show that the main road and the accessory road both produce phase transitions. These phase transitions will often be influenced by the number of lanes, lane changing, the ramp flow, the input flow rate, and the geometry structure. (interdisciplinary physics and related areas of science and technology)

Advanced Modeling of Ramp Operations including Departure Status at Secondary Airports, Phase I

Data.gov (United States)

National Aeronautics and Space Administration — This project addresses three modeling elements relevant to NASA's IADS research and ATD-2 project, two related to ramp operations at primary airports and one related...

The Role of Social Norms in the Portion Size Effect: Reducing normative relevance reduces the effect of portion size on consumption decisions

Directory of Open Access Journals (Sweden)

Iris eVersluis

2016-05-01

Full Text Available People typically eat more from large portions of food than from small portions. An explanation that has often been given for this so-called portion size effect is that the portion size acts as a social norm and as such communicates how much is appropriate to eat. In this paper, we tested this explanation by examining whether manipulating the relevance of the portion size as a social norm changes the portion size effect, as assessed by prospective consumption decisions. We conducted one pilot experiment and one full experiment in which participants respectively indicated how much they would eat or serve themselves from a given amount of different foods. In the pilot (N = 63, we manipulated normative relevance by allegedly basing the portion size on the behavior of either students of the own university (in-group or of another university (out-group. In the main experiment (N = 321, we told participants that either a minority or majority of people similar to them approved of the portion size. Results show that in both experiments, participants expected to serve themselves and to eat more from larger than from smaller portions. As expected, however, the portion size effect was less pronounced when the reference portions were allegedly based on the behavior of an out-group (pilot or approved only by a minority (main experiment. These findings suggest that the portion size indeed provides normative information, because participants were less influenced by it if it communicated the behaviors or values of a less relevant social group. In addition, in the main experiment, the relation between portion size and the expected amount served was partially mediated by the amount that was considered appropriate, suggesting that concerns about eating an appropriate amount indeed play a role in the portion size effect. However, since the portion size effect was weakened but not eliminated by the normative relevance manipulations and since mediation was only partial

Does Stepwise Voltage Ramping Protect the Kidney from Injury During Extracorporeal Shockwave Lithotripsy? Results of a Prospective Randomized Trial.

Science.gov (United States)

Skuginna, Veronika; Nguyen, Daniel P; Seiler, Roland; Kiss, Bernhard; Thalmann, George N; Roth, Beat

2016-02-01

Renal damage is more frequent with new-generation lithotripters. However, animal studies suggest that voltage ramping minimizes the risk of complications following extracorporeal shock wave lithotripsy (SWL). In the clinical setting, the optimal voltage strategy remains unclear. To evaluate whether stepwise voltage ramping can protect the kidney from damage during SWL. A total of 418 patients with solitary or multiple unilateral kidney stones were randomized to receive SWL using a Modulith SLX-F2 lithotripter with either stepwise voltage ramping (n=213) or a fixed maximal voltage (n=205). SWL. The primary outcome was sonographic evidence of renal hematomas. Secondary outcomes included levels of urinary markers of renal damage, stone disintegration, stone-free rate, and rates of secondary interventions within 3 mo of SWL. Descriptive statistics were used to compare clinical outcomes between the two groups. A logistic regression model was generated to assess predictors of hematomas. Significantly fewer hematomas occurred in the ramping group(12/213, 5.6%) than in the fixed group (27/205, 13%; p=0.008). There was some evidence that the fixed group had higher urinary β2-microglobulin levels after SWL compared to the ramping group (p=0.06). Urinary microalbumin levels, stone disintegration, stone-free rate, and rates of secondary interventions did not significantly differ between the groups. The logistic regression model showed a significantly higher risk of renal hematomas in older patients (odds ratio [OR] 1.03, 95% confidence interval [CI] 1.00-1.05; p=0.04). Stepwise voltage ramping was associated with a lower risk of hematomas (OR 0.39, 95% CI 0.19-0.80; p=0.01). The study was limited by the use of ultrasound to detect hematomas. In this prospective randomized study, stepwise voltage ramping during SWL was associated with a lower risk of renal damage compared to a fixed maximal voltage without compromising treatment effectiveness. Lithotripsy is a noninvasive

Implications of sea-level rise in a modern carbonate ramp setting

Science.gov (United States)

Lokier, Stephen W.; Court, Wesley M.; Onuma, Takumi; Paul, Andreas

2018-03-01

This study addresses a gap in our understanding of the effects of sea-level rise on the sedimentary systems and morphological development of recent and ancient carbonate ramp settings. Many ancient carbonate sequences are interpreted as having been deposited in carbonate ramp settings. These settings are poorly-represented in the Recent. The study documents the present-day transgressive flooding of the Abu Dhabi coastline at the southern shoreline of the Arabian/Persian Gulf, a carbonate ramp depositional system that is widely employed as a Recent analogue for numerous ancient carbonate systems. Fourteen years of field-based observations are integrated with historical and recent high-resolution satellite imagery in order to document and assess the onset of flooding. Predicted rates of transgression (i.e. landward movement of the shoreline) of 2.5 m yr- 1 (± 0.2 m yr- 1) based on global sea-level rise alone were far exceeded by the flooding rate calculated from the back-stepping of coastal features (10-29 m yr- 1). This discrepancy results from the dynamic nature of the flooding with increased water depth exposing the coastline to increased erosion and, thereby, enhancing back-stepping. A non-accretionary transgressive shoreline trajectory results from relatively rapid sea-level rise coupled with a low-angle ramp geometry and a paucity of sediments. The flooding is represented by the landward migration of facies belts, a range of erosive features and the onset of bioturbation. Employing Intergovernmental Panel on Climate Change (Church et al., 2013) predictions for 21st century sea-level rise, and allowing for the post-flooding lag time that is typical for the start-up of carbonate factories, it is calculated that the coastline will continue to retrograde for the foreseeable future. Total passive flooding (without considering feedback in the modification of the shoreline) by the year 2100 is calculated to likely be between 340 and 571 m with a flooding rate of 3

Stokes line width

International Nuclear Information System (INIS)

Nikiskov, A.I.; Ritus, V.I.

1993-01-01

The concept of Stokes line width is introduced for the asymptotic expansions of functions near an essential singularity. Explicit expressions are found for functions (switching functions) that switch on the exponentially small terms for the Dawson integral, Airy function, and the gamma function. A different, more natural representation of a function, not associated with expansion in an asymptotic series, in the form of dominant and recessive terms is obtained by a special division of the contour integral which represents the function into contributions of higher and lower saddle points. This division leads to a narrower, natural Stokes line width and a switching function of an argument that depends on the topology of the lines of steepest descent from the saddle point

Non-timber forest products: ramps in the Waynesville, NC watershed

Science.gov (United States)

Kristina Connor; Jim Chamberlain III; Hilliard Gibbs Jr.; Matt Winn

2015-01-01

The potential of forest farming was noted as far back as 1929, but the recognition of its importance dates back only 20 to 30 years. The U.S. market for harvested foods and medicinal plants from forests now exceeds $4 billion annually. Ramps (Allium tricoccum Aiton), or wild leeks, grow in patches in the rich moist forests of the eastern United...

Optimizing the current ramp-up phase for the hybrid ITER scenario

NARCIS (Netherlands)

Hogeweij, G.M.D.; Artaud, J.F.; Casper, T.A.; Citrin, J.; Imbeaux, F.; Köchl, F.; Litaudon, X.; Voitsekhovitch, I.

2013-01-01

The current ramp-up phase for the ITER hybrid scenario is analysed with the CRONOS integrated modelling suite. The simulations presented in this paper show that the heating systems available at ITER allow, within the operational limits, the attainment of a hybrid q profile at the end of the current

Masses, widths, and leptonic widths of the higher upsilon resonances

International Nuclear Information System (INIS)

Lovelock, D.M.J.; Horstkotte, J.E.; Klopfenstein, C.

1985-01-01

The masses, total widths, and leptonic widths of three triplet s-wave bb-bar states UPSILON(4S), UPSILON(5S), and UPSILON(6S) are determined from measurements of the e + e - annihilation cross section into hadrons for 10.55< W<11.25 GeV. The resonances are identified from potential model results and their properties are obtained with the help of a simplified coupled-channels calculation. We find M(4S) = 10.577 GeV, GAMMA(4S) = 25 MeV, GAMMA/sub e/e(4S) = 0.28 keV; M(5S) = 10.845 GeV, GAMMA(5S) = 110 MeV, GAMMA/sub e/e(5S) = 0.37 keV; M(6S) = 11.02 GeV, GAMMA(6S) = 90 MeV, GAMMA/sub e/e(6S) = 0.16 keV

RaMP: A Comprehensive Relational Database of Metabolomics Pathways for Pathway Enrichment Analysis of Genes and Metabolites.

Science.gov (United States)

Zhang, Bofei; Hu, Senyang; Baskin, Elizabeth; Patt, Andrew; Siddiqui, Jalal K; Mathé, Ewy A

2018-02-22

The value of metabolomics in translational research is undeniable, and metabolomics data are increasingly generated in large cohorts. The functional interpretation of disease-associated metabolites though is difficult, and the biological mechanisms that underlie cell type or disease-specific metabolomics profiles are oftentimes unknown. To help fully exploit metabolomics data and to aid in its interpretation, analysis of metabolomics data with other complementary omics data, including transcriptomics, is helpful. To facilitate such analyses at a pathway level, we have developed RaMP (Relational database of Metabolomics Pathways), which combines biological pathways from the Kyoto Encyclopedia of Genes and Genomes (KEGG), Reactome, WikiPathways, and the Human Metabolome DataBase (HMDB). To the best of our knowledge, an off-the-shelf, public database that maps genes and metabolites to biochemical/disease pathways and can readily be integrated into other existing software is currently lacking. For consistent and comprehensive analysis, RaMP enables batch and complex queries (e.g., list all metabolites involved in glycolysis and lung cancer), can readily be integrated into pathway analysis tools, and supports pathway overrepresentation analysis given a list of genes and/or metabolites of interest. For usability, we have developed a RaMP R package (https://github.com/Mathelab/RaMP-DB), including a user-friendly RShiny web application, that supports basic simple and batch queries, pathway overrepresentation analysis given a list of genes or metabolites of interest, and network visualization of gene-metabolite relationships. The package also includes the raw database file (mysql dump), thereby providing a stand-alone downloadable framework for public use and integration with other tools. In addition, the Python code needed to recreate the database on another system is also publicly available (https://github.com/Mathelab/RaMP-BackEnd). Updates for databases in RaMP will be

Ramp - Metering Algorithms Evaluated within Simplified Conditions

Science.gov (United States)

Janota, Aleš; Holečko, Peter; Gregor, Michal; Hruboš, Marián

2017-12-01

Freeway networks reach their limits, since it is usually impossible to increase traffic volumes by indefinitely extending transport infrastructure through adding new traffic lanes. One of the possible solutions is to use advanced intelligent transport systems, particularly ramp metering systems. The paper shows how two particular algorithms of local and traffic-responsive control (Zone, ALINEA) can be adapted to simplified conditions corresponding to Slovak freeways. Both control strategies are modelled and simulated using PTV Vissim software, including the module VisVAP. Presented results demonstrate the properties of both control strategies, which are compared mutually as well as with the initial situation in which no control strategy is applied

Ramp - Metering Algorithms Evaluated within Simplified Conditions

Directory of Open Access Journals (Sweden)

Janota Aleš

2017-12-01

Full Text Available Freeway networks reach their limits, since it is usually impossible to increase traffic volumes by indefinitely extending transport infrastructure through adding new traffic lanes. One of the possible solutions is to use advanced intelligent transport systems, particularly ramp metering systems. The paper shows how two particular algorithms of local and traffic-responsive control (Zone, ALINEA can be adapted to simplified conditions corresponding to Slovak freeways. Both control strategies are modelled and simulated using PTV Vissim software, including the module VisVAP. Presented results demonstrate the properties of both control strategies, which are compared mutually as well as with the initial situation in which no control strategy is applied

Study On Application Of Molecular Techniques (RAPD-PCR And RAMP-PCR) To Detect Mutation In Rice Breeding

International Nuclear Information System (INIS)

Hoang Thi My Linh; Phan, D. T. Son; Nguyen Thi Vang; Nguyen, T. T. Hien; Le XuanTham

2007-01-01

The project was carried out in 2007 with the purpose of consideration for using the two simple and inexpensive molecular techniques to estimate changes in DNA of rice mutant after gamma irradiation. Three rice cultivars: Basmati370, Tam Thom (TT1), IR64 and three gamma irradiated mutants BDS, TDS and VND 95-20 respectively, were used. Suitable DNA extraction procedure was obtained. PCR optimization was conducted on three important factors including: amount of MgCl 2 , DNA concentration and annealing temperature. 2.5 mM of MgCl 2 for RAPD-PCR and 3.75 mM for RAMP-PCR were found the best. 40 ng DNA provided a good amplification for RAMP-PCR; this figure was 50 ng for RAPD-PCR. Annealing temperatures were determined at 36 o C for RAPD primer and at 55±3 o C for Microsatellite primer. Final results showed that, both RAPD-PCR and RAMP-PCR could detect changes in DNA of rice mutants after gamma irradiation compared to their parents. Percentage of DNA changes determined by RAPD-PCR and RAMP-PCR on Basmati370 and its mutant BDS were 11.49% and 21.2% respectively; These on TT1 and TDS were 8.98% and 15.4%; and on IR64 and VND 95-20 were 3.45% and 4.95%. (author)

Tree-ring proxies of larch bud moth defoliation: latewood width and blue intensity are more precise than tree-ring width.

Science.gov (United States)

Arbellay, Estelle; Jarvis, Ingrid; Chavardès, Raphaël D; Daniels, Lori D; Stoffel, Markus

2018-05-19

Reconstructions of defoliation by larch bud moth (LBM, Zeiraphera diniana Gn.) based on European larch (Larix decidua Mill.) tree rings have unraveled outbreak patterns over exceptional temporal and spatial scales. In this study, we conducted tree-ring analyses on 105 increment cores of European larch from the Valais Alps, Switzerland. The well-documented history of LBM outbreaks in Valais provided a solid baseline for evaluating the LBM defoliation signal in multiple tree-ring parameters. First, we used tree-ring width measurements along with regional records of LBM outbreaks to reconstruct the occurrence of these events at two sites within the Swiss Alps. Second, we measured earlywood width, latewood width and blue intensity, and compared these parameters with tree-ring width to assess the capacity of each proxy to detect LBM defoliation. A total of six LBM outbreaks were reconstructed for the two sites between AD 1850 and 2000. Growth suppression induced by LBM was, on average, highest in latewood width (59%), followed by total ring width (54%), earlywood width (51%) and blue intensity (26%). We show that latewood width and blue intensity can improve the temporal accuracy of LBM outbreak reconstructions, as both proxies systematically detected LBM defoliation in the first year it occurred, as well as the differentiation between defoliation and non-defoliation years. This study introduces blue intensity as a promising new proxy of insect defoliation and encourages its use in conjunction with latewood width.

Design, fabrication, installation and flight service evaluation of a composite cargo ramp skin on a model CH-53 helicopter

Science.gov (United States)

Lowry, D. W.; Rich, M. J.

1983-01-01

The installation of a composite skin panel on the cargo ramp of a CH-530 marine helicopter is discussed. The composite material is of Kevlar/Epoxy (K/E) which replaces aluminum outer skins on the aft two bays of the ramp. The cargo ramp aft region was selected as being a helicopter airframe surface subjected to possible significant field damage and would permit an evaluation of the long term durability of the composite skin panel. A structural analysis was performed and the skin shears determined. Single lap joints of K/E riveted to aluminum were statically tested. The joint tests were used to determine bearing allowables and the required K/E skin gage. The K/E skin panels riveted to aluminum edge members were tested in a shear fixture to confirm the allowable shear and bearing strengths. Impact tests were conducted on aluminum skin panels to determine energy level and damage relationship. The K/E skin panels of various ply orientations and laminate thicknesses were then impacted at similar energy levels. The results of the analysis and tests were used to determine the required K/E skin gages in each of the end two bays of the ramp.

An independent system operator's perspective on operational ramp forecasting

Energy Technology Data Exchange (ETDEWEB)

Porter, G. [New Brunswick System Operator, Fredericton, NB (Canada)

2010-07-01

One of the principal roles of the power system operator is to select the most economical resources to reliably supply electric system power needs. Operational wind power production forecasts are required by system operators in order to understand the impact of ramp event forecasting on dispatch functions. A centralized dispatch approach can contribute to a more efficient use of resources that traditional economic dispatch methods. Wind ramping events can have a significant impact on system reliability. Power systems can have constrained or robust transmission systems, and may also be islanded or have large connections to neighbouring systems. Power resources can include both flexible and inflexible generation resources. Wind integration tools must be used by system operators to improve communications and connections with wind power plants. Improved wind forecasting techniques are also needed. Sensitivity to forecast errors is dependent on current system conditions. System operators require basic production forecasts, probabilistic forecasts, and event forecasts. Forecasting errors were presented as well as charts outlining the implications of various forecasts. tabs., figs.

Narrow-width mechanism of a=5 Ξ-state

International Nuclear Information System (INIS)

Kumagai-Fuse, I.; Akaishi, Y.

1995-04-01

Narrow-width mechanism of ≡ 5 H is discussed by calculating conversion widths to all its possible decay channels. Since the conversion processes have small reaction Q values, the three- and four- body decays are strongly suppressed owing to small phase volumes available. Decay widths to the two-body channels are significantly reduced by the distortion of emitted-particle waves. This mechanism brings about a narrow width of ≡ 5 H. The total width is estimated to be 0.87 MeV, in which the largest contribution comes from the decay into the Λ 4 H * +Λ channel. (author)

Level width broadening effect

International Nuclear Information System (INIS)

Zhang Jingshang

2003-01-01

In file-6 for double-differential cross sections, the level width broadening effect should be taken into account properly due to Heisenberg' uncertainty. Besides level width broadening effect, the energy resolution in the measurements is also needed in fitting measurement procedure. In general, the traditional normal Gaussian expansion is employed. However, to do so in this way the energy balance could not be held. For this reason, the deformed Gaussian expansion functions with exponential form for both the single energy point and continuous spectrum are introduced, with which the normalization and energy balance conditions could be held exactly in the analytical form. (author)

Fast current ramp experiments on TFTR

International Nuclear Information System (INIS)

Fredrickson, E.D.; McGuire, K.; Goldston, R.J.

1987-05-01

Electron heat transport on TFTR and other tokamaks is several orders of magnitude larger than neoclassical calculations would predict. Despite considerable effort, there is still no clear theoretical understanding of this anomalous transport. The electron temperature profile T/sub e/(r), shape has shown a marked consistency on many machines, including TFTR, for a wide range of plasma parameters and heating profiles. This could be an important clue as to the process responsible for this enhanced thermal transport. In this paper 'profile consistency' in TFTR is described and an experiment which uses a fast current ramp to transiently decouple the current density profile J(r), and the T/sub e/(r) profiles is discussed. From this experiment the influence of J(r) on electron temperature profile consistency can be determined

LHC Report: Ramp-up complete

CERN Multimedia

Mike Lamont for the LHC Team

2012-01-01

The intensity ramp-up outlined in the last Bulletin continued more or less as planned, with some steady running with 1092 bunches followed by the final step-up to 1380 – the maximum number of bunches for the year.   Monday, 16 April was spent performing luminosity calibration. Under carefully controlled conditions and a special beam configuration, the experiments' luminosity measurements were calibrated against a measurement of the accelerator’s absolute luminosity obtained with Van der Meer scans. These scans give the beam sizes at the interaction point which, together with an accurate measurement of the beam and bunch currents (and other more subtle considerations), allow a precise measurement of the absolute luminosity. With the Van der Meer scans out of the way, the final step-up in the number of bunches to 1380 was made. This has resulted in an average peak luminosity of around 5.6x1033 cm-2s-1 in the general-purpose detectors (ATLAS and CMS have yet to publish th...

Overview on international experimental programmes on power ramping and fission gas release

International Nuclear Information System (INIS)

Knaab, H.; Lang, P.M.; Mogard, H.

1983-01-01

During the last years a number of internationally sponsored experimental programmes were initiated to study the LWR fuel behaviour during ramping and fission gas release at higher burnup levels. Common interest and the limited availability of experimental facilities and appropriate test fuel rods have led to valuable cooperation of many organizations throughout the nuclear community. These programmes are performed by the experimental staff from research centers with their experimental facilities. Fuel vendors and several utilities contribute by supply and irradiation of test fuel rods. The aim of this paper is to provide a synopsis of the following programmes: Studsvik Projects: Interramp, Overramp, Superramp, Demoramp I and II; Petten, High Burnup PWR Ramp Test Programme; Mol, Tribulation Programme; BNWL, High Burnup Effects Programme; Risoe Fission Gas Project; Related tasks within the OECD Halden Reactor Project. The objectives of the programme, their work scope and main results will be summarized on the basis of presently available information. An outlook to future proposed programmes will be given. (author)

Overview on international experimental programmes on power ramping and fission gas release

International Nuclear Information System (INIS)

Knaab, H.; Lang, P.M.

1985-01-01

During the last few years a number of internationally sponsored experimental programmes have been initiated to study LWR fuel behaviour during ramping and fission gas release at high burnup levels. Common interest and the limited availability of experimental facilities and appropriate test fuel rods have led to valuable cooperation between many organizations throughout the nuclear community. These programmes are carried out by experienced staff from research centres using the centres' experimental facilities. Fuel vendors and several utilities contribute by supplying and irradiating the test fuel rods. The aim of this paper is to provide a synopsis of the following programmes: (a) Studsvik Projects: Interramp, Demoramp I and II, Overramp, Superramp; (b) Petten, High Burnup PWR Ramp Test Programme; (c) Mol, Tribulation Programme; (d) BNWL, High Burnup Effects Programme; (e) Riso Fission Gas Project; and (f) related tasks within the OECD Halden Reactor Project. The objectives of the programmes, their scope and the main results will be summarized. An overview of proposed future programmes will be given. (author)

Dispersive traveling wave solutions of the Equal-Width and Modified Equal-Width equations via mathematical methods and its applications

Science.gov (United States)

Lu, Dianchen; Seadawy, Aly R.; Ali, Asghar

2018-06-01

The Equal-Width and Modified Equal-Width equations are used as a model in partial differential equations for the simulation of one-dimensional wave transmission in nonlinear media with dispersion processes. In this article we have employed extend simple equation method and the exp(-varphi(ξ)) expansion method to construct the exact traveling wave solutions of equal width and modified equal width equations. The obtained results are novel and have numerous applications in current areas of research in mathematical physics. It is exposed that our method, with the help of symbolic computation, provides a effective and powerful mathematical tool for solving different kind nonlinear wave problems.

Brain response to food cues varying in portion size is associated with individual differences in the portion size effect in children

NARCIS (Netherlands)

Keller, Kathleen L.; English, Laural K.; Fearnbach, S.N.; Lasschuijt, Marlou; Anderson, Kaitlin; Bermudez, Maria; Fisher, Jennifer O.; Rolls, Barbara J.; Wilson, Stephen J.

2018-01-01

Large portions promote intake of energy dense foods (i.e., the portion size effect–PSE), but the neurobiological drivers of this effect are not known. We tested the association between blood oxygen level dependent (BOLD) brain response to food images varied by portion size (PS) and energy density

Effect of geometry on the downstream flow topology of a micro ramp in a supersonic turbulent boundary layer : An experimental study

NARCIS (Netherlands)

Tambe, S.S.; Schrijer, F.F.J.; van Oudheusden, B.W.

2017-01-01

The physical relation between the geometry and the flow topology of the wake of a micro ramp is investigated by means of a parametric study. Various micro ramp geometries are placed in a supersonic turbulent boundary layer at a free-stream Mach number of 2. The flow field is measured with schlieren

Control of the neutronic and thermohydraulic conditions of power ramps in an irradiation loop for PWR fuel rod; Controle des conditions neutroniques et thermohydrauliques des rampes de puissance dans une boucle d`irradiation de combustibles de reacteur a eau pressurisee

Energy Technology Data Exchange (ETDEWEB)

Moulin, D J.F.

1993-09-10

In order to study the power transients effects on PWR fuel rod clad, ramp tests in a pressurized water loop, are carried out at OSIRIS reactor. The present thesis deals with the on-line control of the device, during power ramp and conditioning irradiation. Based on a convolution-type resolution of the kinetics equations, a dynamic compensation of the Silver self-powered neutron detector was developed. With this method, the uncertainty of the ramp end-point is lower than 1%, thus it is very suited for monitoring both transient, as well as steady state conditions. Furthermore, a thermohydraulic model of the irradiation device is described: heat transfer equations, including gamma heating in materials, are solved to obtain temperatures and thermal fluxes of steady states. Results from the model and temperature measurements of the coolant are used together for fuel power determination, in real time. The clad external temperature profile is also calculated and displayed, to improve the irradiation monitoring. (author), 51 refs., 12 annexes, 66 figs.

Tourniquet pressures: strap width and tensioning system widths.

Science.gov (United States)

Wall, Piper L; Coughlin, Ohmar; Rometti, Mary; Birkholz, Sarah; Gildemaster, Yvonne; Grulke, Lisa; Sahr, Sheryl; Buising, Charisse M

2014-01-01

Pressure distribution over tourniquet width is a determinant of pressure needed for arterial occlusion. Different width tensioning systems could result in arterial occlusion pressure differences among nonelastic strap designs of equal width. Ratcheting Medical Tourniquets (RMTs; m2 inc., http://www.ratcheting buckles.com) with a 1.9 cm-wide (Tactical RMT) or 2.3 cm-wide (Mass Casualty RMT) ladder were directly compared (16 recipients, 16 thighs and 16 upper arms for each tourniquetx2). Then, RMTs were retrospectively compared with the windlass Combat Application Tourniquet (C-A-T ["CAT"], http://combattourniquet.com) with a 2.5 cm-wide internal tensioning strap. Pressure was measured with an air-filled No. 1 neonatal blood pressure cuff under each 3.8 cm-wide tourniquet. RMT circumferential pressure distribution was not uniform. Tactical RMT pressures were not higher, and there were no differences between the RMTs in the effectiveness, ease of use ("97% easy"), or discomfort. However, a difference did occur regarding tooth skipping of the pawl during ratchet advancement: it occurred in 1 of 64 Tactical RMT applications versus 27 of 64 Mass Casualty RMT applications. CAT and RMT occlusion pressures were frequently over 300 mmHg. RMT arm occlusion pressures (175-397 mmHg), however, were lower than RMT thigh occlusion pressures (197-562 mmHg). RMT effectiveness was better with 99% reached occlusion and 1% lost occlusion over 1 minute versus the CAT with 95% reached occlusion and 28% lost occlusion over 1 minute. RMT muscle tension changes (up to 232 mmHg) and pressure losses over 1 minute (24±11 mmHg arm under strap to 40±12 mmHg thigh under ladder) suggest more occlusion losses may have occurred if tourniquet duration was extended. The narrower tensioning system Tactical RMT has better performance characteristics than the Mass Casualty RMT. The 3.8 cm-wide RMTs have some pressure and effectiveness similarities and differences compared with the CAT. Clinically

Localization of ionization-induced trapping in a laser wakefield accelerator using a density down-ramp

CERN Document Server

Hansson, M.; Ekerfelt, H.; Aurand, B.; Gallardo Ganzalez, I.; Desforges, F. G.; Davoine, X.; Maitrallain, A.; Reymond, S.; Monot, P.; Persson, A.; Dobosz Dufrénoy S.; Wahlström C-G.; Cros, B.; Lundh, O.

2016-01-01

We report on a study on controlled trapping of electrons, by field ionization of nitrogen ions, in laser wakefield accelerators in variable length gas cells. In addition to ionization-induced trapping in the density plateau inside the cells, which results in wide, but stable, electron energy spectra, a regime of ionization-induced trapping localized in the density down-ramp at the exit of the gas cells, is found. The resulting electron energy spectra are peaked, with 10% shot-to-shot fluctuations in peak energy. Ionization-induced trapping of electrons in the density down-ramp is a way to trap and accelerate a large number of electrons, thus improving the efficiency of the laser-driven wakefield acceleration.

Hong's grading for evaluating anterior chamber angle width.

Science.gov (United States)

Kim, Seok Hwan; Kang, Ja Heon; Park, Ki Ho; Hong, Chul

2012-11-01

To compare Hong's grading method with anterior segment optical coherence tomography (AS-OCT), gonioscopy, and the dark-room prone-position test (DRPT) for evaluating anterior chamber width. The anterior chamber angle was graded using Hong's grading method, and Hong's angle width was calculated from the arctangent of Hong's grades. The correlation between Hong's angle width and AS-OCT parameters was analyzed. The area under the receiver operating characteristic curve (AUC) for Hong's grading method when discriminating between narrow and open angles as determined by gonioscopy was calculated. Correlation analysis was performed between Hong's angle width and intraocular pressure (IOP) changes determined by DRPT. A total of 60 subjects were enrolled. Of these subjects, 53.5 % had a narrow angle. Hong's angle width correlated significantly with the AS-OCT parameters (r = 0.562-0.719, P < 0.01). A Bland-Altman plot showed relatively good agreement between Hong's angle width and the angle width obtained by AS-OCT. The ability of Hong's grading method to discriminate between open and narrow angles was good (AUC = 0.868, 95 % CI 0.756-0.942). A significant linear correlation was found between Hong's angle width and IOP change determined by DRPT (r = -0.761, P < 0.01). Hong's grading method is useful for detecting narrow angles. Hong's grading correlated well with AS-OCT parameters and DRPT.

Chemistry of decomposition of freshwater wetland sedimentary organic material during ramped pyrolysis

Science.gov (United States)

Williams, E. K.; Rosenheim, B. E.

2011-12-01

Ramped pyrolysis methodology, such as that used in the programmed-temperature pyrolysis/combustion system (PTP/CS), improves radiocarbon analysis of geologic materials devoid of authigenic carbonate compounds and with low concentrations of extractable authochthonous organic molecules. The approach has improved sediment chronology in organic-rich sediments proximal to Antarctic ice shelves (Rosenheim et al., 2008) and constrained the carbon sequestration potential of suspended sediments in the lower Mississippi River (Roe et al., in review). Although ramped pyrolysis allows for separation of sedimentary organic material based upon relative reactivity, chemical information (i.e. chemical composition of pyrolysis products) is lost during the in-line combustion of pyrolysis products. A first order approximation of ramped pyrolysis/combustion system CO2 evolution, employing a simple Gaussian decomposition routine, has been useful (Rosenheim et al., 2008), but improvements may be possible. First, without prior compound-specific extractions, the molecular composition of sedimentary organic matter is unknown and/or unidentifiable. Second, even if determined as constituents of sedimentary organic material, many organic compounds have unknown or variable decomposition temperatures. Third, mixtures of organic compounds may result in significant chemistry within the pyrolysis reactor, prior to introduction of oxygen along the flow path. Gaussian decomposition of the reaction rate may be too simple to fully explain the combination of these factors. To relate both the radiocarbon age over different temperature intervals and the pyrolysis reaction thermograph (temperature (°C) vs. CO2 evolved (μmol)) obtained from PTP/CS to chemical composition of sedimentary organic material, we present a modeling framework developed based upon the ramped pyrolysis decomposition of simple mixtures of organic compounds (i.e. cellulose, lignin, plant fatty acids, etc.) often found in sedimentary

Sand ramps as palaeoenvironmental archives: Integrating general principles and regional contexts through reanalysis of the Klipkraal Sands, South Africa

Science.gov (United States)

Rowell, Alexandra L. K.; Thomas, David S. G.; Bailey, Richard M.; Holmes, Peter J.

2018-06-01

Sand ramps occur on a continuum of topographically-controlled landforms, ranging from purely aeolian features (climbing/falling dunes) to talus cones and alluvial fans. Sand ramps have been identified as potentially important palaeoenvironmental archives in dryland regions that possess relatively few Quaternary proxy records. Their utility however requires not only good age control of depositional phases but clear identification of process regimes, determined through morphological and sedimentological analyses, with several recent studies indicating the complexities of palaeoenvironmental interpretations and the controls of ramp development (Bateman et al., 2012; Rowell et al., 2018). Klipkraal Sands is a sand ramp on the north-eastern margin of the semi-arid Karoo that has been important for inferences of the extent of southern African Late Quaternary aeolian activity (Thomas et al., 2002). We reanalyse this feature, in the light of both its significance and other recent studies that have inferred extensive southern African LGM aeolian activity (Telfer et al., 2012, 2014). New sedimentological data and twelve OSL dates indicate the Klipkraal Sands formed episodically between 100-0.14 ka, rather than accumulating rapidly, while sedimentological data question the aeolian affinities of the bulk of the feature. Therefore, Klipkraal is reinterpreted as showing no particular affinity to the LGM, with sediments locally sourced with a significant colluvial component. Only the upper historical sediments can be clearly interpreted as aeolian deposits. A complex interplay of processes is suggested, for which a meaningful palaeoenvironmental interpretation cannot be easily defined. This implies that the local geomorphic processes and controls operating on sand ramps need to be established before they can be fully utilised as palaeoenvironmental archives, with implications for their interpretation worldwide.

Half-width at half-maximum, full-width at half-maximum analysis

Indian Academy of Sciences (India)

addition to the well-defined parameter full-width at half-maximum (FWHM). The distribution of ... optical side-lobes in the diffraction pattern resulting in steep central maxima [6], reduc- tion of effects of ... and broad central peak. The idea of.

Comparison of functional ramp walk test and 6-min walk test in healthy volunteers: A new approach in functional capacity evaluation

Directory of Open Access Journals (Sweden)

Manivel Arumugam

2017-01-01

Full Text Available Objective: Inclined surfaces or ramps are the common obstacles faced by elderly and cardiopulmonary disabled in accessing public amenities. Ramp walking is one of the most common functional demands to be met by a common man in the industrialized world. To assess the functional (uphill walking capacity, we need a different functional stress test over the routinely used 6-min walk test (6MWT. Hence, a new 3-min steep ramp walk test (3MRWT was constructed to meet the demands similar to an uphill walk and to provide more functional stress than routinely used 6MWT. Methodology: The observational, crossover study design was adopted for this study. Fifteen healthy participants (8 males, 7 females performed both tests in a randomized order with a washout time of 6 h in between the tests. Walking distance to both ramp and ground, heart rate, blood pressure, saturation (SpO2, dyspnea, and fatigue with Borg exertion scale were compared prior and after the two walk tests. Results: The average distances covered in 6MWT were 510.5 ± 55.06 and 440.65 ± 25.08 meters and in 3MRWT were 270.18 ± 30.8, 230.05 ± 15.06 meters for male and female respectively. The difference between 3MRWT and 6MWT distances covered by the participants was statistically significant (t = 0.893. The mean difference between the heart rate, saturation and perceptions were highly significant (P < 0.001. Conclusion: The study results show that 3MRWT is valid over routinely administered 6MWT and may provide greater functional stress (uphill or ramp walk capacity in a shorter duration in healthy individuals in assessing the maximal functional capacity in a ramp or uphill walking.

A Multicenter, Randomized Trial of Ramped Position vs Sniffing Position During Endotracheal Intubation of Critically Ill Adults.

Science.gov (United States)

Semler, Matthew W; Janz, David R; Russell, Derek W; Casey, Jonathan D; Lentz, Robert J; Zouk, Aline N; deBoisblanc, Bennett P; Santanilla, Jairo I; Khan, Yasin A; Joffe, Aaron M; Stigler, William S; Rice, Todd W

2017-10-01

Hypoxemia is the most common complication during endotracheal intubation of critically ill adults. Intubation in the ramped position has been hypothesized to prevent hypoxemia by increasing functional residual capacity and decreasing the duration of intubation, but has never been studied outside of the operating room. Multicenter, randomized trial comparing the ramped position (head of the bed elevated to 25°) with the sniffing position (torso supine, neck flexed, and head extended) among 260 adults undergoing endotracheal intubation by pulmonary and critical care medicine fellows in four ICUs between July 22, 2015, and July 19, 2016. The primary outcome was lowest arterial oxygen saturation between induction and 2 minutes after intubation. Secondary outcomes included Cormack-Lehane grade of glottic view, difficulty of intubation, and number of laryngoscopy attempts. The median lowest arterial oxygen saturation was 93% (interquartile range [IQR], 84%-99%) with the ramped position vs 92% (IQR, 79%-98%) with the sniffing position (P = .27). The ramped position appeared to increase the incidence of grade III or IV view (25.4% vs 11.5%, P = .01), increase the incidence of difficult intubation (12.3% vs 4.6%, P = .04), and decrease the rate of intubation on the first attempt (76.2% vs 85.4%, P = .02), respectively. In this multicenter trial, the ramped position did not improve oxygenation during endotracheal intubation of critically ill adults compared with the sniffing position. The ramped position may worsen glottic view and increase the number of laryngoscopy attempts required for successful intubation. ClinicalTrials.gov; No.: NCT02497729; URL: www.clinicaltrials.gov. Copyright © 2017 American College of Chest Physicians. Published by Elsevier Inc. All rights reserved.

Resident-Assisted Montessori Programming (RAMP): training persons with dementia to serve as group activity leaders.

Science.gov (United States)

Camp, Cameron J; Skrajner, Michael J

2004-06-01

The purpose of this study was to determine the effects of an activity implemented by means of Resident-Assisted Montessori Programming (RAMP). Four persons with early-stage dementia were trained to serve as leaders for a small-group activity played by nine persons with more advanced dementia. Assessments of leaders' ability to learn the procedures of leading a group, as well as their satisfaction with this role, were taken, as were measures of players' engagement and affect during standard activities programming and RAMP activities. Leaders demonstrated the potential to fill the role of group activity leader effectively, and they expressed a high level of satisfaction with this role. Players' levels of positive engagement and pleasure during the RAMP activity were higher than during standard group activities. This study suggests that to the extent that procedural learning is available to persons with early-stage dementia, especially when they are assisted with external cueing, these individuals can successfully fill the role of volunteers when working with persons with more advanced dementia. This can provide a meaningful social role for leaders and increase access to high quality activities programming for large numbers of persons with dementia. Copyright 2004 The Gerontological Society of America

Dorsal stream involvement in recognition of objects with transient onset but not with ramped onset

Directory of Open Access Journals (Sweden)

Lourenco Tomas

2011-08-01

Full Text Available Abstract Background Although the ventral visual stream is understood to be responsible for object recognition, it has been proposed that the dorsal stream may contribute to object recognition by rapidly activating parietal attention mechanisms, prior to ventral stream object processing. Methods To investigate the relative contribution of the dorsal visual stream to object recognition a group of tertiary students were divided into good and poor motion coherence groups and assessed on tasks classically assumed to rely on ventral stream processing. Participants were required to identify simple line drawings in two tasks, one where objects were presented abruptly for 50 ms followed by a white-noise mask, the other where contrast was linearly ramped on and off over 325 ms and replaced with a mask. Results Although both groups only differed in motion coherence performance (a dorsal stream measure, the good motion coherence group showed superior contrast sensitivity for object recognition on the abrupt, but not the ramped presentation tasks. Conclusions We propose that abrupt presentation of objects activated attention mechanisms fed by the dorsal stream, whereas the ramped presentation had reduced transience and thus did not activate dorsal attention mechanisms as well. The results suggest that rapid dorsal stream activation may be required to assist with ventral stream object processing.

Jumps of the local magnetic field near CICC during external magnetic field ramp and their connection with the ramp rate limitation

International Nuclear Information System (INIS)

Vysotsky, V.S.; Takayasu, M.; Minervini, J.V.

1997-01-01

A new method has been developed to study Ramp Rate Limitation (RRL) phenomena. Samples of ITER-type cable-in-conduit (CICC) subcable were instrumented with local field sensors such as Hall probes and pick-up coils and then subjected to rapidly changing external magnetic field. The authors found that during fast field sweeps some discontinuous changes, or jumps occur in the local field. They believe that these jumps indicate a fast current redistribution processes inside CICC. Detailed information about local magnetic field jumps during changing field is presented. Possible origin of the jumps and their connection with RRL are discussed

Eddy current heating of irregularly shaped plates by slow ramped fields

International Nuclear Information System (INIS)

Dresner, L.

1979-01-01

Theorems are presented for estimating eddy current heating of irregularly shaped plates by a perpendicular ramped field. The theorems, which are derived from two complementary variational principles, give upper and lower bounds to the eddy current heating. Illustrative results are given for rectangles, isosceles triangles, sectors of circular annuli, rhombuses, and L-shaped plates. A comparison is made with earlier work

EVALUATION OF SEISMIC PERFORMANCE OF RAMP TUNNEL STRUCTURE DURING LEVEL-2 EARTHQUAKE BY MASSIVE 3D NUMERICAL COMPUTATION

Science.gov (United States)

Yamada, Takemine; Ichimura, Tsuyoshi; Hori, Muneo; Dobashi, Hiroshi; Ohbo, Naoto

Quasi non-linear 3D FEM earthquake response analysises with level-2 earthquake are conducted for a ramp tunnel structure of Tokyo metropolitan express way central circular line the Yamate tunnel. Large-scale numerical computation with solid elements is highly required for examination of seismic response of large tunnel in case of level-2 earthquake. The results are obtained as follows: i) In level-2 earthquake, stress concentration in ramp tunnel becomes great near geological interface between two layers of high impedance contrast. ii) The response is not obtained as a superposition of two-dimensional responses which is an assumption in conventional design methods because the distribution of displacements in the direction of tunnel axis at cross-section of ramp tunnel structure near geological interface does not linearly distribute. iii) Evaluation of stress in addition to section force is desirable for the correct evaluation of the three-dimensional response of tunnel structure.

A quantitative analysis of transtensional margin width

Science.gov (United States)

Jeanniot, Ludovic; Buiter, Susanne J. H.

2018-06-01

Continental rifted margins show variations between a few hundred to almost a thousand kilometres in their conjugated widths from the relatively undisturbed continent to the oceanic crust. Analogue and numerical modelling results suggest that the conjugated width of rifted margins may have a relationship to their obliquity of divergence, with narrower margins occurring for higher obliquity. We here test this prediction by analysing the obliquity and rift width for 26 segments of transtensional conjugate rifted margins in the Atlantic and Indian Oceans. We use the plate reconstruction software GPlates (http://www.gplates.org) for different plate rotation models to estimate the direction and magnitude of rifting from the initial phases of continental rifting until breakup. Our rift width corresponds to the distance between the onshore maximum topography and the last identified continental crust. We find a weak positive correlation between the obliquity of rifting and rift width. Highly oblique margins are narrower than orthogonal margins, as expected from analogue and numerical models. We find no relationships between rift obliquities and rift duration nor the presence or absence of Large Igneous Provinces (LIPs).

Children's estimates of food portion size: the development and evaluation of three portion size assessment tools for use with children.

Science.gov (United States)

Foster, E; Matthews, J N S; Lloyd, J; Marshall, L; Mathers, J C; Nelson, M; Barton, K L; Wrieden, W L; Cornelissen, P; Harris, J; Adamson, A J

2008-01-01

A number of methods have been developed to assist subjects in providing an estimate of portion size but their application in improving portion size estimation by children has not been investigated systematically. The aim was to develop portion size assessment tools for use with children and to assess the accuracy of children's estimates of portion size using the tools. The tools were food photographs, food models and an interactive portion size assessment system (IPSAS). Children (n 201), aged 4-16 years, were supplied with known quantities of food to eat, in school. Food leftovers were weighed. Children estimated the amount of each food using each tool, 24 h after consuming the food. The age-specific portion sizes represented were based on portion sizes consumed by children in a national survey. Significant differences were found between the accuracy of estimates using the three tools. Children of all ages performed well using the IPSAS and food photographs. The accuracy and precision of estimates made using the food models were poor. For all tools, estimates of the amount of food served were more accurate than estimates of the amount consumed. Issues relating to reporting of foods left over which impact on estimates of the amounts of foods actually consumed require further study. The IPSAS has shown potential for assessment of dietary intake with children. Before practical application in assessment of dietary intake of children the tool would need to be expanded to cover a wider range of foods and to be validated in a 'real-life' situation.

Lake Basin Fetch and Maximum Length/Width

Data.gov (United States)

Minnesota Department of Natural Resources — Linear features representing the Fetch, Maximum Length and Maximum Width of a lake basin. Fetch, maximum length and average width are calcuated from the lake polygon...

Evaluation of width and width uniformity of near-field electrospinning printed micro and sub-micrometer lines based on optical image processing

Science.gov (United States)

Zhao, Libo; Xia, Yong; Hebibul, Rahman; Wang, Jiuhong; Zhou, Xiangyang; Hu, Yingjie; Li, Zhikang; Luo, Guoxi; Zhao, Yulong; Jiang, Zhuangde

2018-03-01

This paper presents an experimental study using image processing to investigate width and width uniformity of sub-micrometer polyethylene oxide (PEO) lines fabricated by near-filed electrospinning (NFES) technique. An adaptive thresholding method was developed to determine the optimal gray values to accurately extract profiles of printed lines from original optical images. And it was proved with good feasibility. The mechanism of the proposed thresholding method was believed to take advantage of statistic property and get rid of halo induced errors. Triangular method and relative standard deviation (RSD) were introduced to calculate line width and width uniformity, respectively. Based on these image processing methods, the effects of process parameters including substrate speed (v), applied voltage (U), nozzle-to-collector distance (H), and syringe pump flow rate (Q) on width and width uniformity of printed lines were discussed. The research results are helpful to promote the NFES technique for fabricating high resolution micro and sub-micro lines and also helpful to optical image processing at sub-micro level.

Power ramping, cycling and load following behaviour of water reactor fuel

International Nuclear Information System (INIS)

1988-05-01

The present meeting was scheduled by the International Atomic Energy Agency upon proposal of the Members of the International Working Group on Water Reactor Fuel Performance and Technology. Sixty-three participants representing 15 countries and one international organization attended the meeting. Twenty papers were presented during three technical sessions, followed by panel discussions which allowed to formulate the conclusions of the meeting and recommendations to the Agency. The objective of this Technical Committee Meeting is to review the ''State-of-the-Art'', make critical comments and recommendations with the aim of improving fuel reliability and assure integrity of the cladding and core materials when subjected to ramping and cycling sequences. The Meeting was organized in three sessions: Session 1. ''Mechanical Behaviour and Fission Gas Release'' (7 papers); Session 2. ''Power Ramping and Power Cycling Demonstration Programmes in Research Reactors'' (5 papers); Session 3. ''Fuel Behaviour in Power Reactors'' (9 papers). Between the sessions, the session chairmen, together with the speakers, prepared and presented reports with summary, conclusions and recommendations of the individual sessions. These reports are added to this summary report. A separate abstract was prepared for each of these 21 presentations. Refs, figs and tabs

Numerical optimization of the ramp-down phase with the RAPTOR code

Science.gov (United States)

Teplukhina, Anna; Sauter, Olivier; Felici, Federico; The Tcv Team; The ASDEX-Upgrade Team; The Eurofusion Mst1 Team

2017-10-01

The ramp-down optimization goal in this work is defined as the fastest possible decrease of a plasma current while avoiding any disruptions caused by reaching physical or technical limits. Numerical simulations and preliminary experiments on TCV and AUG have shown that a fast decrease of plasma elongation and an adequate timing of the H-L transition during current ramp-down can help to avoid reaching high values of the plasma internal inductance. The RAPTOR code (F. Felici et al., 2012 PPCF 54; F. Felici, 2011 EPFL PhD thesis), developed for real-time plasma control, has been used for an optimization problem solving. Recently the transport model has been extended to include the ion temperature and electron density transport equations in addition to the electron temperature and current density transport equations, increasing the physical applications of the code. The gradient-based models for the transport coefficients (O. Sauter et al., 2014 PPCF 21; D. Kim et al., 2016 PPCF 58) have been implemented to RAPTOR and tested during this work. Simulations of the AUG and TCV entire plasma discharges will be presented. See the author list of S. Coda et al., Nucl. Fusion 57 2017 102011.

Masses, widths and leptonic widths of the higher upsilon resonances

International Nuclear Information System (INIS)

Klopfenstein, C.; Lovelock, D.M.J.; Horstkotte, J.E.

1985-01-01

The masses, total widths and leptonic widths of three triplet s-wave bb-bar states Υ(4S), Υ(5S) and Υ(6S) are determined by unfolding the cross section features observed in the hadronic cross section in the √s region betweeen 10.55 to 11.25 GeV. Both the identification of the resonances and the deduction of their properties rely on the validity of potential models' description of heavy quarkonium states which lie close (<0.6 GeV) to the open flavor threshold. The authors find M(4S) = 10.5774 +- 0.0008 GeV, Γ(4S) = 23 +- 2.3 MeV, Γ/sub ee/(4S) = 0.28 +- 0.04 keV; M(5S) = 10.845 +- 0.02 GeV, Γ(5S) = 110 +- 15 MeV, Γ/sub ee/(5S) = 0.37 +- 0.06 keV; M(6S) = 11.02 +- 0.03 GeV, Γ(6S) = 90 +- 20 MeV, Γ/sub ee/(6S) = 0.16 +- 0.04 keV. All errors are statistical only

Effects of Lane Width, Lane Position and Edge Shoulder Width on Driving Behavior in Underground Urban Expressways: A Driving Simulator Study

Directory of Open Access Journals (Sweden)

Shuo Liu

2016-10-01

Full Text Available This study tested the effects of lane width, lane position and edge shoulder width on driving behavior for a three-lane underground urban expressway. A driving simulator was used with 24 volunteer test subjects. Five lane widths (2.85, 3.00, 3.25, 3.50, and 3.75 m and three shoulder widths (0.50, 0.75, and 1.00 m were studied. Driving speed, lane deviation and subjective perception of driving behavior were collected as performance measures. The results show that lane and shoulder width have significant effects on driving speed. Average driving speed increases from 60.01 km/h in the narrowest lane to 88.05 km/h in the widest lane. While both narrower lanes and shoulders result in reduced speed and lateral lane deviation, the effect of lane width is greater than that of shoulder width. When the lane and shoulder are narrow, drivers in the left or right lane tend to shy away from the tunnel wall, even encroaching into the neighboring middle lane. As the lane or shoulder gets wider, drivers tend to stay in the middle of the lane. An interesting finding is that although few participants acknowledged that lane position had any great bearing on their driving behaviors, the observed driving speed is statistically higher in the left lane than in the other two lanes when the lane width is narrow (in 2.85, 3 and 3.25 m lanes. These findings provided support for amending the current design specifications of urban underground roads, such as the relationship between design speed and lane width, speed limit, and combination form of lanes.

Portion Sizes from 24-Hour Dietary Recalls Differed by Sex among Those Who Selected the Same Portion Size Category on a Food Frequency Questionnaire.

Science.gov (United States)

Kang, Minji; Park, Song-Yi; Boushey, Carol J; Wilkens, Lynne R; Monroe, Kristine R; Le Marchand, Loïc; Kolonel, Laurence N; Murphy, Suzanne P; Paik, Hee-Young

2018-05-08

Accounting for sex differences in food portions may improve dietary measurement; however, this factor has not been well examined. The aim of this study was to examine sex differences in reported food portions from 24-hour dietary recalls (24HDRs) among those who selected the same portion size category on a quantitative food frequency questionnaire (QFFQ). This study was conducted with a cross-sectional design. Participants (n=319) were members of the Hawaii-Los Angeles Multiethnic Cohort who completed three 24HDRs and a QFFQ in a calibration study conducted in 2010 and 2011. Portions of individual foods reported from 24HDRs served as the outcome measures. Mean food portions from 24HDRs were compared between men and women who reported the same portion size on the QFFQ, after adjustment for race/ethnicity using a linear regression model. Actual amount and the assigned amount of the selected portion size in the QFFQ were compared using one-sample t test for men and women separately. Of 163 food items with portion size options listed in the QFFQ, 32 were reported in 24HDRs by ≥20 men and ≥20 women who selected the same portion size in the QFFQ. Although they chose the same portion size on the QFFQ, mean intake amounts from 24HDRs were significantly higher for men than for women for "beef/lamb/veal," "white rice," "brown/wild rice," "lettuce/tossed salad," "eggs cooked/raw," "whole wheat/rye bread," "buns/rolls," and "mayonnaise in sandwiches." For men, mean portions of 14 items from the 24HDRs were significantly different from the assigned amounts for QFFQ items (seven higher and seven lower), whereas for women, mean portions of 14 items were significantly lower from the assigned amounts (with five significantly higher). These sex differences in reported 24HDR food portions-even among participants who selected the same portion size on the QFFQ-suggest that the use of methods that account for differences in the portions consumed by men and women when QFFQs are

The role of temperature ramp-up time before barrier layer growth in optical and structural properties of InGaN/GaN multi-quantum wells

Science.gov (United States)

Xing, Yao; Zhao, Degang; Jiang, Desheng; Liu, Zongshun; Zhu, Jianjun; Chen, Ping; Yang, Jing; Liu, Wei; Liang, Feng; Liu, Shuangtao; Zhang, Liqun; Wang, Wenjie; Li, Mo; Zhang, Yuantao; Du, Guotong

2018-05-01

In InGaN/GaN multi-quantum wells (MQWs), a low temperature cap (LT-cap) layer is grown between the InGaN well layer and low temperature GaN barrier layer. During the growth, a temperature ramp-up and ramp-down process is added between LT-cap and barrier layer growth. The effect of temperature ramp-up time duration on structural and optical properties of quantum wells is studied. It is found that as the ramp-up time increases, the Indium floating layer on the top of the well layer can be diminished effectively, leading to a better interface quality between well and barrier layers, and the carrier localization effect is enhanced, thereby the internal quantum efficiency (IQE) of QWs increases surprisingly. However, if the ramp-up time is too long, the carrier localization effect is weaker, which may increase the probabilities of carriers to meet with nonradiative recombination centers. Meanwhile, more nonradiative recombination centers will be introduced into well layers due to the indium evaporation. Both of them will lead to a reduction of internal quantum efficiency (IQE) of MQWs.

Comparison of Arch Width Changes Following Orthodontic ...

African Journals Online (AJOL)

2015-11-21

Nov 21, 2015 ... Materials and Methods: The study was conducted with pre- and post-treatment digital models from ... or posterior arch width following orthodontic treatment ..... premolar extraction cases show significant arch width increases in ...

Beam-width spreading of vortex beams in free space

Science.gov (United States)

Wang, Weiwei; Li, Jinhong; Duan, Meiling

2018-01-01

Based on the extended Huygens-Fresnel principle and the definition of second-order moments of the Wigner distribution function, the analytical expression for the beam-width spreading of Gaussian Schell-model (GSM) vortex beams in free space are derived, and used to study the influence of beam parameters on the beam-width spreading of GSM vortex beams. With the increment of the propagation distance, the beam-width spreading of GSM vortex beams will increase; the bigger the topological charge, spatial correlation length, wavelength and waist width are, the smaller the beam-width spreading is.

Modeling ramp-hold indentation measurements based on Kelvin-Voigt fractional derivative model

Science.gov (United States)

Zhang, Hongmei; zhe Zhang, Qing; Ruan, Litao; Duan, Junbo; Wan, Mingxi; Insana, Michael F.

2018-03-01

Interpretation of experimental data from micro- and nano-scale indentation testing is highly dependent on the constitutive model selected to relate measurements to mechanical properties. The Kelvin-Voigt fractional derivative model (KVFD) offers a compact set of viscoelastic features appropriate for characterizing soft biological materials. This paper provides a set of KVFD solutions for converting indentation testing data acquired for different geometries and scales into viscoelastic properties of soft materials. These solutions, which are mostly in closed-form, apply to ramp-hold relaxation, load-unload and ramp-load creep-testing protocols. We report on applications of these model solutions to macro- and nano-indentation testing of hydrogels, gastric cancer cells and ex vivo breast tissue samples using an atomic force microscope (AFM). We also applied KVFD models to clinical ultrasonic breast data using a compression plate as required for elasticity imaging. Together the results show that KVFD models fit a broad range of experimental data with a correlation coefficient typically R 2  >  0.99. For hydrogel samples, estimation of KVFD model parameters from test data using spherical indentation versus plate compression as well as ramp relaxation versus load-unload compression all agree within one standard deviation. Results from measurements made using macro- and nano-scale indentation agree in trend. For gastric cell and ex vivo breast tissue measurements, KVFD moduli are, respectively, 1/3-1/2 and 1/6 of the elasticity modulus found from the Sneddon model. In vivo breast tissue measurements yield model parameters consistent with literature results. The consistency of results found for a broad range of experimental parameters suggest the KVFD model is a reliable tool for exploring intrinsic features of the cell/tissue microenvironments.

40 CFR 86.1362-2007 - Steady-state testing with a ramped-modal cycle.

Science.gov (United States)

2010-07-01

...-modal cycle. 86.1362-2007 Section 86.1362-2007 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... (CONTINUED) Emission Regulations for New Otto-Cycle and Diesel Heavy-Duty Engines; Gaseous and Particulate Exhaust Test Procedures § 86.1362-2007 Steady-state testing with a ramped-modal cycle. This section...

40 CFR 86.1362-2010 - Steady-state testing with a ramped-modal cycle.

Science.gov (United States)

2010-07-01

...-modal cycle. 86.1362-2010 Section 86.1362-2010 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... (CONTINUED) Emission Regulations for New Otto-Cycle and Diesel Heavy-Duty Engines; Gaseous and Particulate Exhaust Test Procedures § 86.1362-2010 Steady-state testing with a ramped-modal cycle. This section...

Operational experiences of the spallation neutron source superconducting linac and power ramp-up

International Nuclear Information System (INIS)

Kim, Sang-Ho

2009-01-01

The spallation neutron source (SNS) is a second generation pulsed neutron source and designed to provide a 1-GeV, 1.44-MW proton beam to a mercury target for neutron production. Since the commissioning of the accelerator complex in 2006, the SNS has started its operation for neutron production and beam power ramp-up has been in progress toward the design goal. All subsystems of the SNS were designed and developed for substantial improvements compared to existing accelerators because the design beam power is almost an order of magnitude higher compared to existing neutron facilities and the achievable neutron scattering performance will exceed present sources by more than a factor of 20 to 100. In this paper, the operational experiences with the SNS Superconducting Linac (SCL), Power Ramp-up Plan to reach the design goal and the Power Upgrade Plan (PUP) will be presented including machine, subsystem and beam related issues.

Spherical bodies of constant width

OpenAIRE

Lassak, Marek; Musielak, Michał

2018-01-01

The intersection $L$ of two different non-opposite hemispheres $G$ and $H$ of a $d$-dimensional sphere $S^d$ is called a lune. By the thickness of $L$ we mean the distance of the centers of the $(d-1)$-dimensional hemispheres bounding $L$. For a hemisphere $G$ supporting a %spherical convex body $C \\subset S^d$ we define ${\\rm width}_G(C)$ as the thickness of the narrowest lune or lunes of the form $G \\cap H$ containing $C$. If ${\\rm width}_G(C) =w$ for every hemisphere $G$ supporting $C$, we...

The Effects of Using a Ramp and Elevator to Load and Unload Trailers on the Behavior and Physiology of Piglets.

Science.gov (United States)

McGlone, John; Sapkota, Avi

2014-09-11

Transport is an inevitable process in the modern U.S. swine industry. The loading process is a novel and potentially stressful experience. This study uses behavior, heart rate and leukocyte counts to compare stress one hour before, during and after loading via ramp or elevator. Piglets were held in a home pen (control (CON)), walked up and down an aisle (handled (HAN)), or walked to a truck and loaded via elevator (ELE) or ramp (RAM). Sitting, feeding and blood parameters did not show a significant treatment by time effect (p > 0.05). Standing behavior did not differ between CON and HAN piglets nor between RAM and ELE piglets (p > 0.05); however, CON and HAN piglets stood more than RAM and ELE piglets during treatment (p elevated 2.4% (p elevator appears to be less stressful than loading by ramp.

Stieltjes-moment-theory technique for calculating resonance width's

International Nuclear Information System (INIS)

Hazi, A.U.

1978-12-01

A recently developed method for calculating the widths of atomic and molecular resonances is reviewed. The method is based on the golden-rule definition of the resonance width, GAMMA(E). The method uses only square-integrable, L 2 , basis functions to describe both the resonant and the non-resonant parts of the scattering wave function. It employs Stieltjes-moment-theory techniques to extract a continuous approximation for the width discrete representation of the background continuum. Its implementation requires only existing atomic and molecular structure codes. Many-electron effects, such as correlation and polarization, are easily incorporated into the calculation of the width via configuration interaction techniques. Once the width, GAMMA(E), has been determined, the energy shift can be computed by a straightforward evaluation of the required principal-value integral. The main disadvantage of the method is that it provides only the total width of a resonance which decays into more than one channel in a multichannel problem. A review of the various aspects of the theory is given first, and then representative results that have been obtained with this method for several atomic and molecular resonances are discussed. 28 references, 3 figures, 4 tables

Diagnostic de fonctionnement d’une rampe frontale adoptée dans une grande exploitation irriguée du Nord-Ouest Tunisien

Directory of Open Access Journals (Sweden)

Youssef M'SADAK

2017-09-01

Full Text Available The objective of this study is to diagnose the field operation of a combined ramp during its first campaign at a large private farm, located in the Borj Elamri delegation, governorate of Manouba (North of Tunisia, to shed light on the quality of the irrigation obtained. This work was devoted to the evaluation of the water distribution, the coefficient of uniformity and possible corrections of the adopted nozzle distribution according to the plan indicated by the manufacturer. On the other hand, we verified conformity between theoretical and actual nozzle plan by placing nozzles at their correct position on the ramp and also tested the uniform distribution of the water. The uniformity tests carried out on the side of the ramp covered a range of prevailing wind speeds of 1 to 6 m/s and a pressure range of 1.6 to 3.5 bars. The operation diagnostics detected that the studied system (pivot-ramp presented a simple dual-function nozzles (different from the generally used double nozzle plan with nozzles in good condition with a slight deviation of the flows at the level of the pivot and the front ramp. The linear mode of this system is less wind sensitive and less energy-intensive than the pivot mode. The latter revealed an overall coefficient of uniformity of about 83%, lower than that of the linear mode (86%. Finally, the future use of such a mechanized sprinkler system is not the optimum solution, due in particular to their complexity of design, assembly, operation and use.

The decay width of stringy hadrons

Science.gov (United States)

Sonnenschein, Jacob; Weissman, Dorin

2018-02-01

In this paper we further develop a string model of hadrons by computing their strong decay widths and comparing them to experiment. The main decay mechanism is that of a string splitting into two strings. The corresponding total decay width behaves as Γ = π/2 ATL where T and L are the tension and length of the string and A is a dimensionless universal constant. We show that this result holds for a bosonic string not only in the critical dimension. The partial width of a given decay mode is given by Γi / Γ =Φi exp ⁡ (- 2 πCmsep2 / T) where Φi is a phase space factor, msep is the mass of the "quark" and "antiquark" created at the splitting point, and C is a dimensionless coefficient close to unity. Based on the spectra of hadrons we observe that their (modified) Regge trajectories are characterized by a negative intercept. This implies a repulsive Casimir force that gives the string a "zero point length". We fit the theoretical decay width to experimental data for mesons on the trajectories of ρ, ω, π, η, K*, ϕ, D, and Ds*, and of the baryons N, Δ, Λ, and Σ. We examine both the linearity in L and the exponential suppression factor. The linearity was found to agree with the data well for mesons but less for baryons. The extracted coefficient for mesons A = 0.095 ± 0.015 is indeed quite universal. The exponential suppression was applied to both strong and radiative decays. We discuss the relation with string fragmentation and jet formation. We extract the quark-diquark structure of baryons from their decays. A stringy mechanism for Zweig suppressed decays of quarkonia is proposed and is shown to reproduce the decay width of ϒ states. The dependence of the width on spin and flavor symmetry is discussed. We further apply this model to the decays of glueballs and exotic hadrons.

Step width alters iliotibial band strain during running.

Science.gov (United States)

Meardon, Stacey A; Campbell, Samuel; Derrick, Timothy R

2012-11-01

This study assessed the effect of step width during running on factors related to iliotibial band (ITB) syndrome. Three-dimensional (3D) kinematics and kinetics were recorded from 15 healthy recreational runners during overground running under various step width conditions (preferred and at least +/- 5% of their leg length). Strain and strain rate were estimated from a musculoskeletal model of the lower extremity. Greater ITB strain and strain rate were found in the narrower step width condition (p running, especially in persons whose running style is characterized by a narrow step width, may be beneficial in the treatment and prevention of running-related ITB syndrome.

Palindromic widths of nilpotent and wreath products

Indian Academy of Sciences (India)

Palindromic width; commutator width; wreath products; nilpotent product. 2000 Mathematics ... An algorithm of the computation of the commutator length in free non-abelian .... It is clear that A(1)B = A × B is the direct sum. Let us list some ...

Study of electro-optic effect in asymmetrically ramped AlInGaAs multiple quantum well structures

Energy Technology Data Exchange (ETDEWEB)

Sadiq, Muhammad Usman; Peters, Frank H.; Corbett, Brian [Tyndall National Institute, Lee Maltings, Cork (Ireland); Department of Physics, University College Cork, Cork (Ireland); O' Callaghan, James; Roycroft, Brendan; Thomas, Kevin; Pelucchi, Emanuele [Tyndall National Institute, Lee Maltings, Cork (Ireland)

2016-04-15

We investigate the electro-optic properties of two oppositely ramped asymmetric quantum well structures in the AlInGaAs material system. The grading of the bandgap in the quantum wells has been achieved by changing the ratio of Al to Ga in the quaternary alloy during the epitaxial growth. The surface normal photo-response and the Fabry-Perot fringe shift in straight waveguides are compared for both structures as a function of applied voltage at 1550 nm for TE-polarized light. The measurements show a change in the refractive index due to a red shift of the excitonic resonances due to the quantum-confined Stark effect. The 10 quantum well structure with a ramp up of the bandgap in the growth direction leads to the figure of merit of the voltage for a π phase shift, V{sub π} by length, L, V{sub π} x L, of 6 as compared to 7 V . mm in the structure with a ramp in opposite direction. Further investigations show that the reduction in V{sub π} is due to increased absorption at high reverse bias which induces a non-linear phase change. (copyright 2015 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Sedimentary mode and reservoir genesis of dual grain banks at the Lower Cambrian Longwangmiao Fm carbonate ramp in the Sichuan Basin

Directory of Open Access Journals (Sweden)

Jinhu Du

2016-11-01

Full Text Available The gas reservoir of the Lower Cambrian Longwangmiao Fm in the Sichuan Basin is a supergiant integral marine carbonate gas reservoir whose single scale is currently the largest in China. In order to figure out its sedimentary model and reservoir genesis, its geological structures and sedimentary settings and facies were analyzed comprehensively and the lithofacies paleographic map was plotted. It is revealed that the following sedimentary facies are successively developed in the Longwangmiao Fm from West Sichuan to Southeast Chongqing: diamictic tidal flat at the back ramp, grain bank (the upper bank at the inner/shallow ramp – interbank sea (depression, deeper open bay at the platform depression of inner ramp → evaporative lagoon → evaporative tidal flat, tempestite at the middle ramp – barrier beach – mud mound beach (the lower bank, and outer ramp – basin. Accordingly, the specific sedimentary model of dual grain banks in the Longwangmiao Fm carbonate ramp was established as follows. Firstly, in this model, dual grain banks are symmetrically developed with Wanzhou–Yibin platform depression as the axis, on whose dual sides the paleohighs have shallow water bodies with strong energy. Compared with the classical model, the new one has a new upper bank which is developed around the paleohighs covering an area of about 8 × 104 km2. Secondly, the upper bank is large for its paleogeomorphology being located at the highest position with the strongest water energy during deposition. Therefore, it is prone to dolomitization and meteoric dissolution respectively during contemporaneous–penecontemporaneous hot-dry and hot-humid periods, and especially the Caledonian–Early Hercynian denudation wedge out tends to undergo post-supergene multiphase karstification. Therefore, quality reservoirs are more developed on scale. Thirdly, the intergranular pores and vermes moldic pores were dissolved and enlarged due to the multiphase

Strong self-focusing of a cosh-Gaussian laser beam in collisionless magneto-plasma under plasma density ramp

International Nuclear Information System (INIS)

Nanda, Vikas; Kant, Niti

2014-01-01

The effect of plasma density ramp on self-focusing of cosh-Gaussian laser beam considering ponderomotive nonlinearity is analyzed using WKB and paraxial approximation. It is noticed that cosh-Gaussian laser beam focused earlier than Gaussian beam. The focusing and de-focusing nature of the cosh-Gaussian laser beam with decentered parameter, intensity parameter, magnetic field, and relative density parameter has been studied and strong self-focusing is reported. It is investigated that decentered parameter “b” plays a significant role for the self-focusing of the laser beam as for b=2.12, strong self-focusing is seen. Further, it is observed that extraordinary mode is more prominent toward self-focusing rather than ordinary mode of propagation. For b=2.12, with the increase in the value of magnetic field self-focusing effect, in case of extraordinary mode, becomes very strong under plasma density ramp. Present study may be very useful in the applications like the generation of inertial fusion energy driven by lasers, laser driven accelerators, and x-ray lasers. Moreover, plasma density ramp plays a vital role to enhance the self-focusing effect

Strong self-focusing of a cosh-Gaussian laser beam in collisionless magneto-plasma under plasma density ramp

Energy Technology Data Exchange (ETDEWEB)

Nanda, Vikas; Kant, Niti, E-mail: nitikant@yahoo.com [Department of Physics, Lovely Professional University, G. T. Road, Phagwara, Punjab 144411 (India)

2014-07-15

The effect of plasma density ramp on self-focusing of cosh-Gaussian laser beam considering ponderomotive nonlinearity is analyzed using WKB and paraxial approximation. It is noticed that cosh-Gaussian laser beam focused earlier than Gaussian beam. The focusing and de-focusing nature of the cosh-Gaussian laser beam with decentered parameter, intensity parameter, magnetic field, and relative density parameter has been studied and strong self-focusing is reported. It is investigated that decentered parameter “b” plays a significant role for the self-focusing of the laser beam as for b=2.12, strong self-focusing is seen. Further, it is observed that extraordinary mode is more prominent toward self-focusing rather than ordinary mode of propagation. For b=2.12, with the increase in the value of magnetic field self-focusing effect, in case of extraordinary mode, becomes very strong under plasma density ramp. Present study may be very useful in the applications like the generation of inertial fusion energy driven by lasers, laser driven accelerators, and x-ray lasers. Moreover, plasma density ramp plays a vital role to enhance the self-focusing effect.

Chromaticity measurement during beam energy ramp in Indus-2

International Nuclear Information System (INIS)

Husain, Riyasat; Vats, D.K.; Ghodke, A.D.

2013-01-01

Chromaticity is one of the important parameters of circular accelerators and plays crucial role in its operation. In Indus-2 storage ring the natural chromaticity is -19 and -12 in horizontal and vertical planes respectively. For the good injection at 550 MeV in Indus-2, chromaticity needs to be kept at (+1, +1). The corrected chromaticity does not remain constant during the energy ramp up to 2.5 GeV. We measured Indus-2 storage ring chromaticity by the conventional RF frequency change method. The measurement method and the result of the measurement are reported in this paper. (author)

Kinect Technology Game Play to Mimic Quake Catcher Network (QCN) Sensor Deployment During a Rapid Aftershock Mobilization Program (RAMP)

Science.gov (United States)

Kilb, D. L.; Yang, A.; Rohrlick, D.; Cochran, E. S.; Lawrence, J.; Chung, A. I.; Neighbors, C.; Choo, Y.

2011-12-01

The Kinect technology allows for hands-free game play, greatly increasing the accessibility of gaming for those uncomfortable using controllers. How it works is the Kinect camera transmits invisible near-infrared light and measures its "time of flight" to reflect off an object, allowing it to distinguish objects within 1 centimeter in depth and 3 mm in height and width. The middleware can also respond to body gestures and voice commands. Here, we use the Kinect Windows SDK software to create a game that mimics how scientists deploy seismic instruments following a large earthquake. The educational goal of the game is to allow the players to explore 3D space as they learn about the Quake Catcher Network's (QCN) Rapid Aftershock Mobilization Program (RAMP). Many of the scenarios within the game are taken from factual RAMP experiences. To date, only the PC platform (or a Mac running PC emulator software) is available for use, but we hope to move to other platforms (e.g., Xbox 360, iPad, iPhone) as they become available. The game is written in programming language C# using Microsoft XNA and Visual Studio 2010, graphic shading is added using High Level Shader Language (HLSL), and rendering is produced using XNA's graphics libraries. Key elements of the game include selecting sensor locations, adequately installing the sensor, and monitoring the incoming data. During game play aftershocks can occur unexpectedly, as can other problems that require attention (e.g., power outages, equipment failure, and theft). The player accrues points for quickly deploying the first sensor (recording as many initial aftershocks as possible), correctly installing the sensors (orientation with respect to north, properly securing, and testing), distributing the sensors adequately in the region, and troubleshooting problems. One can also net points for efficient use of game play time. Setting up for game play in your local environment requires: (1) the Kinect hardware ( $145); (2) a computer

Ascending-ramp biphasic waveform has a lower defibrillation threshold and releases less troponin I than a truncated exponential biphasic waveform.

Science.gov (United States)

Huang, Jian; Walcott, Gregory P; Ruse, Richard B; Bohanan, Scott J; Killingsworth, Cheryl R; Ideker, Raymond E

2012-09-11

We tested the hypothesis that the shape of the shock waveform affects not only the defibrillation threshold but also the amount of cardiac damage. Defibrillation thresholds were determined for 11 waveforms-3 ascending-ramp waveforms, 3 descending-ramp waveforms, 3 rectilinear first-phase biphasic waveforms, a Gurvich waveform, and a truncated exponential biphasic waveform-in 6 pigs with electrodes in the right ventricular apex and superior vena cava. The ascending, descending, and rectilinear waveforms had 4-, 8-, and 16-millisecond first phases and a 3.5-millisecond rectilinear second phase that was half the voltage of the first phase. The exponential biphasic waveform had a 60% first-phase and a 50% second-phase tilt. In a second study, we attempted to defibrillate after 10 seconds of ventricular fibrillation with a single ≈30-J shock (6 pigs successfully defibrillated with 8-millisecond ascending, 8-millisecond rectilinear, and truncated exponential biphasic waveforms). Troponin I blood levels were determined before and 2 to 10 hours after the shock. The lowest-energy defibrillation threshold was for the 8-milliseconds ascending ramp (14.6±7.3 J [mean±SD]), which was significantly less than for the truncated exponential (19.6±6.3 J). Six hours after shock, troponin I was significantly less for the ascending-ramp waveform (0.80±0.54 ng/mL) than for the truncated exponential (1.92±0.47 ng/mL) or the rectilinear waveform (1.17±0.45 ng/mL). The ascending ramp has a significantly lower defibrillation threshold and at ≈30 J causes 58% less troponin I release than the truncated exponential biphasic shock. Therefore, the shock waveform affects both the defibrillation threshold and the amount of cardiac damage.

Ramp Study Hemodynamics, Functional Capacity, and Outcome in Heart Failure Patients with Continuous-Flow Left Ventricular Assist Devices

DEFF Research Database (Denmark)

Jung, Mette H; Gustafsson, Finn; Houston, Brian

2016-01-01

Ramp studies-measuring changes in cardiac parameters as a function of serial pump speed changes (revolutions per minute [rpm])-are increasingly used to evaluate function and malfunction of continuous-flow left ventricular assist devices (CF-LVADs). We hypothesized that ramp studies can predict...... patients (HeartMate II, Thoratec Corporation, Pleasanton, CA). Functional status was evaluated in 70% (31/44); average 6 minute walk test (6MWT) was 312 ± 220 min, New York Heart Association (NYHA) I-II/III-IV (70/30%) and activity scores very low-low/moderate-very high (55/45%). Decrease in pulmonary...

The evaluation of failure stress and released amount of fission product gas of power ramped rod by fuel behaviour analysis code 'FEMAXI-III'

International Nuclear Information System (INIS)

Yanagisawa, Kazuaki; Fujita, Misao

1984-01-01

Pellet-Cladding Interaction(PCI) related in-pile failure of Zircaloy sheathed fuel rod is in general considered to be caused by combination of pellet-cladding mechanical interaction(PCMI) with fuel-cladding chemical interaction(FCCI). An understanding of a basic mechanism of PCI-related fuel failure is therefore necessary to get actual cladding hoop stress from mechanical interaction and released amounts of fission product(FP) gas of aggressive environmental agency from chemical interaction. This paper describes results of code analysis performed on fuel failure to cladding hoop stress and amounts of FP gas released under the condition associated with power ramping. Data from Halden(HBWR) and from Studsvik(R2) are used for code analysis. The fuel behaviour analysis code ''FEMAXI-III'' is used as an analytical tool. The followings are revealed from the study: (1) PCI-related fuel failure is dependent upon cladding hoop stress and released amounts of FP gas at power ramping. (2) Preliminary calculated threshold values of hoop stress and of released amounts of FP gas to PCI failure are respectively 330MPa, 10% under the Halden condition, 190MPa, 5% under the Inter ramp(BWR) condition, and 270MPa, 14% under the Over ramp(PWR) condition. The values of hoop stress calculated are almost in the similar range of those obtained from ex-reactor PCI simulated tests searched from references published. (3) The FEMAXI-III code verification is made in mechanical manner by using in-pile deformation data(diametral strain) obtained from power ramping test undertaken by JAERI. While, the code verification is made in thermal manner by using punctured FP gas data obtained from post irradiation examination performed on non-defected power ramped fuel rods. The calculations are resulted in good agreements to both, mechanical and thermal experimental data suggesting the validity of the code evaluation. (J.P.N.)

Impacts of ramping inflexibility of conventional generators on strategic operation of energy storage facilities

DEFF Research Database (Denmark)

Nasrolahpour, Ehsan; Kazempour, Jalal; Zareipour, Hamidreza

2016-01-01

This paper proposes an approach to assist a pricemaker merchant energy storage facility in making its optimal operation decisions. The facility operates in a pool-based electricity market, where the ramping capability of other resources is limited. Also, wind power resources exist in the system...

What is the role of portion control in weight management?

Science.gov (United States)

Rolls, B J

2014-01-01

Systematic studies have shown that providing individuals with larger portions of foods and beverages leads to substantial increases in energy intake. The effect is sustained over weeks, supporting the possibility that large portions have a role in the development of obesity. The challenge is to find strategies to effectively manage the effects of portion size. One approach involves teaching people to select appropriate portions and to use tools that facilitate portion control. Although tools such as portion-control plates have been shown in several randomized trials to improve weight loss, limited data are available on whether education and tools lead to long-term changes in eating behavior and body weight. Another approach is to use preportioned foods (PPFs) to add structure to meals and minimize decisions about the amount of food to eat. A number of randomized controlled trials have demonstrated the efficacy of both liquid meal replacements and solid PPFs for weight loss and weight loss maintenance, but it is not known if they lead to better understanding of appropriate portions. Although portion control is important for weight management, urging people simply to ‘eat less' of all foods may not be the best approach as high-energy-dense foods disproportionately increase energy intake compared with those lower in energy density. A more effective strategy may be to encourage people to increase the proportion of foods low in energy density in their diets while limiting portions of high-energy-dense foods. If people lower the energy density of their diet, they can eat satisfying portions while managing their body weight. PMID:25033958

ANALISA FATIGUE KEKUATAN STERN RAMP DOOR AKIBAT BEBAN DINAMIS PADA KM. KIRANA I DENGAN METODE ELEMEN HINGGA DISKRIT ELEMEN SEGITIGA PLANE STRESS

Directory of Open Access Journals (Sweden)

Sarjito Jokosisworo

2012-04-01

Full Text Available Kapal KM. Kirana I adalah kapal tipe Ro - Ro Passanger Ship yang beroperasi di Pulau Jawa dengan rute pelayaran Pelabuhan Semarang - Sampit yang mampu mengangkut penumpang dan kendaraan dalam jumlah yang relatif banyak. Untuk memudahkan akses keluar masuk kendaraan yang akan diangkut, maka kapal ini dilengkapi dengan sebuah ramp door sistem steel wire rope yang terletak di bagian buritan kapal (stern ramp door. Ramp door akan menerima beban dinamis secara berulang-ulang sehingga mengakibatkan kelelahan material (fatigue. Analisa fatigue konstruksi rampdoor dilakukan dengan menggunakan metode elemen hingga diskrit segitiga plane stress dengan tujuan untuk mendapatkan hasil analisa yang lebih akurat. Pemodelan dilakukan dengan menggunakan program bantu berbasis CAD, sedangkan untuk analisa fatigue menggunakan program berbasis elemen hingga. Analisa  yang digunakan adalah analisa beban dinamis dengan amplitudo berubah berdasarkan variasi 4 beban kendaran. Untuk mengetahui letak kondisi paling kritis rampdoor dibagi menjadi 3 bagian dengan mengambil lokasi pnode 180, 140, dan 100. Berdasarkan hasil analisa didapat umur ramp door selama 3186 siklus atau 2 tahun 9 bulan 4 hari dan mempunyai nilai intensitas tegangan patah sebenarnya sebesar 400,713 Mpa. 

Global synchronization of parallel processors using clock pulse width modulation

Science.gov (United States)

Chen, Dong; Ellavsky, Matthew R.; Franke, Ross L.; Gara, Alan; Gooding, Thomas M.; Haring, Rudolf A.; Jeanson, Mark J.; Kopcsay, Gerard V.; Liebsch, Thomas A.; Littrell, Daniel; Ohmacht, Martin; Reed, Don D.; Schenck, Brandon E.; Swetz, Richard A.

2013-04-02

A circuit generates a global clock signal with a pulse width modification to synchronize processors in a parallel computing system. The circuit may include a hardware module and a clock splitter. The hardware module may generate a clock signal and performs a pulse width modification on the clock signal. The pulse width modification changes a pulse width within a clock period in the clock signal. The clock splitter may distribute the pulse width modified clock signal to a plurality of processors in the parallel computing system.

Nightside studies of coherent HF Radar spectral width behaviour

Directory of Open Access Journals (Sweden)

E. E. Woodfield

2002-09-01

Full Text Available A previous case study found a relationship between high spectral width measured by the CUTLASS Finland HF radar and elevated electron temperatures observed by the EISCAT and ESR incoherent scatter radars in the post-midnight sector of magnetic local time. This paper expands that work by briefly re-examining that interval and looking in depth at two further case studies. In all three cases a region of high HF spectral width (>200 ms-1 exists poleward of a region of low HF spectral width (<200 ms-1. Each case, however, occurs under quite different geomagnetic conditions. The original case study occurred during an interval with no observed electrojet activity, the second study during a transition from quiet to active conditions with a clear band of ion frictional heating indicating the location of the flow reversal boundary, and the third during an isolated sub-storm. These case studies indicate that the relationship between elevated electron temperature and high HF radar spectral width appears on closed field lines after 03:00 magnetic local time (MLT on the nightside. It is not clear whether the same relationship would hold on open field lines, since our analysis of this relationship is restricted in latitude. We find two important properties of high spectral width data on the nightside. Firstly the high spectral width values occur on both open and closed field lines, and secondly that the power spectra which exhibit high widths are both single-peak and multiple-peak. In general the regions of high spectral width (>200 ms-1 have more multiple-peak spectra than the regions of low spectral widths whilst still maintaining a majority of single-peak spectra. We also find that the region of ion frictional heating is collocated with many multiple-peak HF spectra. Several mechanisms for the generation of high spectral width have been proposed which would produce multiple-peak spectra, these are discussed in relation to the data presented here. Since the

Nightside studies of coherent HF Radar spectral width behaviour

Directory of Open Access Journals (Sweden)

E. E. Woodfield

Full Text Available A previous case study found a relationship between high spectral width measured by the CUTLASS Finland HF radar and elevated electron temperatures observed by the EISCAT and ESR incoherent scatter radars in the post-midnight sector of magnetic local time. This paper expands that work by briefly re-examining that interval and looking in depth at two further case studies. In all three cases a region of high HF spectral width (>200 ms^-1 exists poleward of a region of low HF spectral width (<200 ms^-1. Each case, however, occurs under quite different geomagnetic conditions. The original case study occurred during an interval with no observed electrojet activity, the second study during a transition from quiet to active conditions with a clear band of ion frictional heating indicating the location of the flow reversal boundary, and the third during an isolated sub-storm. These case studies indicate that the relationship between elevated electron temperature and high HF radar spectral width appears on closed field lines after 03:00 magnetic local time (MLT on the nightside. It is not clear whether the same relationship would hold on open field lines, since our analysis of this relationship is restricted in latitude. We find two important properties of high spectral width data on the nightside. Firstly the high spectral width values occur on both open and closed field lines, and secondly that the power spectra which exhibit high widths are both single-peak and multiple-peak. In general the regions of high spectral width (>200 ms^-1 have more multiple-peak spectra than the regions of low spectral widths whilst still maintaining a majority of single-peak spectra. We also find that the region of ion frictional heating is collocated with many multiple-peak HF spectra. Several mechanisms for the generation of high spectral width have been proposed which would produce multiple-peak spectra, these are discussed in relation to

Teknik budi daya larva Hermetia illucens (Linnaeus (Diptera: Stratiomyidae sebagai sumber protein pakan ternak melalui biokonversi limbah loading ramp dari pabrik CPO

Directory of Open Access Journals (Sweden)

Agustin Zarkani

2015-09-01

Full Text Available Larvae of Hermetia illucens fly (Linnaeus is an important source of alternative protein and can be used as pellets for feeds. Currently the production of H. illucens larvae is still limited because its rearing depends on palm kernel meal. The objective of the research is to explore alternative media for rearing, i.e. using loading ramp waste from crude palm oil factory. The study was conducted using physical-chemical analysis of the media. Evaluation of potential rearing media of loading ramp was done by studying the suitability of loading ramp fermented by EM4®, rumen microbes, and organic liquid fertilizer and without fermentation. Treatment media was develop with an enrichment ratio of 1 : 0.25, 1 : 05, and 1 : 1 (v/v for bran and husk, and 1.25, 2.5, and 5% (w/w for coconut sugar. Each experiment was arranged in complete randomized design using 20 larva of the 2nd instar. Larvas were incubated in plastic with tube with diameter of 10 cm and 20 cm in height containing of media 300 g. Response differences in growth and mortality were analyzed by ANOVA and least significant differences test at 0.05 levels. Preference and analysis suitability of the media were conducted using material enrichment. Results show that the loading ramp waste contain 9.80% protein and 10.32% fat. Although the media are could support growth and development of the larvae at different degree, media from waste fermentation POC loading ramp with bran enrichment 1 : 0.5 (v/v is the best media for rearing larva.

Control of quasi-monoenergetic electron beams from laser-plasma accelerators with adjustable shock density profile

Science.gov (United States)

Tsai, Hai-En; Swanson, Kelly K.; Barber, Sam K.; Lehe, Remi; Mao, Hann-Shin; Mittelberger, Daniel E.; Steinke, Sven; Nakamura, Kei; van Tilborg, Jeroen; Schroeder, Carl; Esarey, Eric; Geddes, Cameron G. R.; Leemans, Wim

2018-04-01

The injection physics in a shock-induced density down-ramp injector was characterized, demonstrating precise control of a laser-plasma accelerator (LPA). Using a jet-blade assembly, experiments systematically varied the shock injector profile, including shock angle, shock position, up-ramp width, and acceleration length. Our work demonstrates that beam energy, energy spread, and pointing can be controlled by adjusting these parameters. As a result, an electron beam that was highly tunable from 25 to 300 MeV with 8% energy spread (ΔEFWHM/E), 1.5 mrad divergence, and 0.35 mrad pointing fluctuation was produced. Particle-in-cell simulation characterized how variation in the shock angle and up-ramp width impacted the injection process. This highly controllable LPA represents a suitable, compact electron beam source for LPA applications such as Thomson sources and free-electron lasers.

The Tool Life of Ball Nose end Mill Depending on the Different Types of Ramping

Science.gov (United States)

Vopát, Tomáš; Peterka, Jozef; Kováč, Martin

2014-12-01

The article deals with the cutting tool wear measurement process and tool life of ball nose end mill depending on upward ramping and downward ramping. The aim was to determine and compare the wear (tool life) of ball nose end mill for different types of copy milling operations, as well as to specify particular steps of the measurement process. In addition, we examined and observed cutter contact areas of ball nose end mill with machined material. For tool life test, DMG DMU 85 monoBLOCK 5-axis CNC milling machine was used. In the experiment, cutting speed, feed rate, axial depth of cut and radial depth of cut were not changed. The cutting tool wear was measured on Zoller Genius 3s universal measuring machine. The results show different tool life of ball nose end mills depending on the copy milling strategy.

Leakage detection device for weld portion

International Nuclear Information System (INIS)

Shinkawa, Toshio; Setokuchi, Sadayuki.

1994-01-01

The present invention concerns leakage detection device for weld portions, for example, in a nuclear reactor cavity, which can rapidly detect by remote control. That is, a detection device capable of self running and stopping on a guide rail along a weld line is disposed. The detection device comprises a coating mechanism for automatically coating soap water to the weld portion, a vacuum box capable of evacuating the coated surface and a camera for detecting the presence or absence of the soap bubbles generated under the evacuation. Such a device can conduct, by remote control, self running/stopping along with the weld line, coating of the soap water, settling of the vacuum box and confirmation and recording of foaming by using a television monitor. Accordingly, leakage in the weld portion in the reactor cavity or the like can be inspected. As a result, it greatly contributes to improvement of danger upon worker's operation at high place, detection accuracy and reliability of detection and shortening of operation period. (I.S.)

Constant Width Planar Computation Characterizes ACC0

DEFF Research Database (Denmark)

Hansen, Kristoffer Arnsfelt

2006-01-01

We obtain a characterization of ACC0 in terms of a natural class of constant width circuits, namely in terms of constant width polynomial size planar circuits. This is shown via a characterization of the class of acyclic digraphs which can be embedded on a cylinder surface in such a way that all...

Patterns and trends in food portion sizes, 1977-1998.

Science.gov (United States)

Nielsen, Samara Joy; Popkin, Barry M

While general consensus holds that food portion sizes are increasing, no empirical data have documented actual increases. To determine trends in food portion sizes consumed in the United States, by eating location and food source. Nationally representative data from the Nationwide Food Consumption Survey (1977-1978) and the Continuing Survey of Food Intake by Individuals (1989-1991, 1994-1996, and 1998). The sample consists of 63 380 individuals aged 2 years and older. For each survey year, average portion size consumed from specific food items (salty snacks, desserts, soft drinks, fruit drinks, french fries, hamburgers, cheeseburgers, pizza, and Mexican food) by eating location (home, restaurant, or fast food). Portion sizes vary by food source, with the largest portions consumed at fast food establishments and the smallest at other restaurants. Between 1977 and 1996, food portion sizes increased both inside and outside the home for all categories except pizza. The energy intake and portion size of salty snacks increased by 93 kcal (from 1.0 to 1.6 oz [28.4 to 45.4 g]), soft drinks by 49 kcal (13.1 to 19.9 fl oz [387.4 to 588.4 mL]), hamburgers by 97 kcal (5.7 to 7.0 oz [161.6 to 198.4 g]), french fries by 68 kcal (3.1 to 3.6 oz [87.9 to 102.1 g]), and Mexican food by 133 kcal (6.3 to 8.0 oz [178.6 to 226.8 g]). Portion sizes and energy intake for specific food types have increased markedly with greatest increases for food consumed at fast food establishments and in the home.

Penetration portion shielding structure

International Nuclear Information System (INIS)

Hayashi, Katsumi; Narita, Hitoshi; Handa, Hiroyuki; Takeuchi, Jun; Tozuka, Fumio.

1994-01-01

Openings of a plurality of shieldings for penetration members are aligned to each other, and penetration members are inserted from the openings. Then, the openings of the plurality of shielding members are slightly displaced with each other to make the penetration portions into a helical configuration, so that leakage of radiation is reduced. Upon removal of the members, reverse operation is conducted. When a flowable shielding material is used, the penetration portions are constituted with two plates having previously formed openings and pipes for connecting the openings with each other and a vessel covering the entire of them. After passing the penetration members such as a cable, the relative position of the two plates is changed by twisting, to form a helical configuration which reduces radiation leakage. Since they are bent into the helical configuration, shielding performance is extremely improved compared with a case that radiation leakage is caused from an opening of a straight pipe. In addition, since they can be returned to straight pipes, attachment, detachment and maintenance can be conducted easily. (N.H.)

Driver performance and attention allocation in use of logo signs on freeway exit ramps.

Science.gov (United States)

Zahabi, Maryam; Machado, Patricia; Lau, Mei Ying; Deng, Yulin; Pankok, Carl; Hummer, Joseph; Rasdorf, William; Kaber, David B

2017-11-01

The objective of this research was to quantify the effects of driver age, ramp signage configuration, including number of panels, logo format and sign familiarity, on driver performance and attention allocation when exiting freeways. Sixty drivers participated in a simulator study and analysis of variance models were used to assess response effects of the controlled manipulations. Results revealed elderly drivers to demonstrate worse performance and conservative control strategies as compared to middle-aged and young drivers. Elderly drivers also exhibited lower off-road fixation frequency and shorter off-road glance durations compared to middle-aged and young drivers. In general, drivers adopted a more conservative strategy when exposed to nine-panel signs as compared to six-panel signs and were more accurate in target detection when searching six-panels vs. nine and with familiar vs. unfamiliar logos. These findings provide an applicable guide for agency design of freeway ramp signage accounting for driver demographics. Copyright © 2017 Elsevier Ltd. All rights reserved.

Thermal instability observations during ramp tests in the Studsvik R2 reactor

International Nuclear Information System (INIS)

Roennberg, G.; Kjaer-Pedersen, N.

1984-01-01

A series of ramp tests on ENC-built BWR fuel from the Big Rock Point reactor was performed in September 1982 in the Studsvik R2 Reactor. The tests involved segmented rods with a burnup of 18 MWd/KgU, and constituted part of the Fuel Performance Improvement Program sponsored by the United States Department of Energy. Rods of different designs were tested. The reference design had solid, dished pellets and was unpressurized. The alternative designs were annular pellets and sphere-pac. Some of the rods with annular pellets were prepressurized, and some were not. During the ramp tests the rod power is controlled by a helium depressurization loop which causes a strictly linear power ramp versus time. The thermal output of the test rig is measured calorimetrically, the data immediately being recorded on a strip chart and later processed by a computer. Furthermore, elongation detectors permit the immediate recording of the rod length variation versus time. For some of the rods the thermal output went constant for a fraction of a minute after reaching a certain value, then continued to rise, while the helium depressurization continued to proceed linearly with time. For the duration of this plateau of the thermal output curve the slope of the elongation detector signal was significantly higher than before, but fell back to its original value after the plateau. This observation was made only for the reference rods. None of the annular rods, with or without prepressurization, nor the sphere-pac rods, showed the effect. When observed, the effect occurred at about 40 kw/m. The effect is attributed to fission gas release rapidly being enhanced by thermal feedback. The increase in stored energy associated with the temperature rise in the fuel causes the delay in thermal output. The larger available internal volume and/or the prepressurization of the annular rods, and the lack of a distinct fuel-clad gap for the sphere-pac rods prevented the effect from occurring in those other

Line Width Recovery after Vectorization of Engineering Drawings

Directory of Open Access Journals (Sweden)

Gramblička Matúš

2016-12-01

Full Text Available Vectorization is the conversion process of a raster image representation into a vector representation. The contemporary commercial vectorization software applications do not provide sufficiently high quality outputs for such images as do mechanical engineering drawings. Line width preservation is one of the problems. There are applications which need to know the line width after vectorization because this line attribute carries the important semantic information for the next 3D model generation. This article describes the algorithm that is able to recover line width of individual lines in the vectorized engineering drawings. Two approaches are proposed, one examines the line width at three points, whereas the second uses a variable number of points depending on the line length. The algorithm is tested on real mechanical engineering drawings.

Creating a measure of portion control self-efficacy.

Science.gov (United States)

Fast, Lindsey C; Harman, Jennifer J; Maertens, Julie A; Burnette, Jeni L; Dreith, Francesca

2015-01-01

Over the last few decades, food portion sizes have steadily increased by as much as 700% (Young & Nestle, 2002). Food portions are often much larger than dietary guidelines recommend, leaving individuals to manage their food consumption on their own and making it necessary to understand individual factors impacting food consumption. In the current paper, we focus on self-efficacy for portion control. Specifically, across three studies, we developed and validated a new measure of portion control self-efficacy (PCSE). The PCSE measure yielded good fit statistics and had acceptable test-retest reliability using two cross-sectional surveys (Studies 1(a) and 1(b)). Results from Study 2 demonstrated construct and predictive validity of the PCSE using the Food Amount Rating Scale (FARS; Dohm, & Striegel-Moore, 2002). Study 3 offered additional support for reliability and validity with a sample of overweight and obese adults currently trying to lose weight. Overall, findings indicate that the new PCSE measure is reliable and valid. Individuals often make inaccurate food portion estimates (Slawson & Eck, 1997; Yuhas, Bolland, & Bolland, 1989) which can lead to overeating and weight-gain. Thus, the discussion centers on the need to incorporate PCSE in future research and intervention work targeting weight loss, health, and food consumption. Copyright © 2014 Elsevier Ltd. All rights reserved.

Online Analysis of Wind and Solar Part I: Ramping Tool

Energy Technology Data Exchange (ETDEWEB)

Etingov, Pavel V.; Ma, Jian; Makarov, Yuri V.; Subbarao, Krishnappa

2012-01-31

To facilitate wider penetration of renewable resources without compromising system reliability concerns arising from the lack of predictability of intermittent renewable resources, a tool for use by California Independent System Operator (CAISO) power grid operators was developed by Pacific Northwest National Laboratory (PNNL) in conjunction with CAISO with funding from California Energy Commission. This tool predicts and displays additional capacity and ramping requirements caused by uncertainties in forecasts of loads and renewable generation. The tool is currently operational in the CAISO operations center. This is one of two final reports on the project.

Characterizing graphs of maximum matching width at most 2

DEFF Research Database (Denmark)

Jeong, Jisu; Ok, Seongmin; Suh, Geewon

2017-01-01

The maximum matching width is a width-parameter that is de ned on a branch-decomposition over the vertex set of a graph. The size of a maximum matching in the bipartite graph is used as a cut-function. In this paper, we characterize the graphs of maximum matching width at most 2 using the minor o...

Effect of step width manipulation on tibial stress during running.

Science.gov (United States)

Meardon, Stacey A; Derrick, Timothy R

2014-08-22

Narrow step width has been linked to variables associated with tibial stress fracture. The purpose of this study was to evaluate the effect of step width on bone stresses using a standardized model of the tibia. 15 runners ran at their preferred 5k running velocity in three running conditions, preferred step width (PSW) and PSW±5% of leg length. 10 successful trials of force and 3-D motion data were collected. A combination of inverse dynamics, musculoskeletal modeling and beam theory was used to estimate stresses applied to the tibia using subject-specific anthropometrics and motion data. The tibia was modeled as a hollow ellipse. Multivariate analysis revealed that tibial stresses at the distal 1/3 of the tibia differed with step width manipulation (p=0.002). Compression on the posterior and medial aspect of the tibia was inversely related to step width such that as step width increased, compression on the surface of tibia decreased (linear trend p=0.036 and 0.003). Similarly, tension on the anterior surface of the tibia decreased as step width increased (linear trend p=0.029). Widening step width linearly reduced shear stress at all 4 sites (pstresses experienced by the tibia during running were influenced by step width when using a standardized model of the tibia. Wider step widths were generally associated with reduced loading of the tibia and may benefit runners at risk of or experiencing stress injury at the tibia, especially if they present with a crossover running style. Copyright © 2014 Elsevier Ltd. All rights reserved.

40 CFR 1042.505 - Testing engines using discrete-mode or ramped-modal duty cycles.

Science.gov (United States)

2010-07-01

... ramped-modal duty cycles. 1042.505 Section 1042.505 Protection of Environment ENVIRONMENTAL PROTECTION... duty cycles. This section describes how to test engines under steady-state conditions. In some cases, we allow you to choose the appropriate steady-state duty cycle for an engine. In these cases, you...

ITER-like current ramps in JET with ILW: experiments, modelling and consequences for ITER

Czech Academy of Sciences Publication Activity Database

Hogeweij, G.M.D.; Calabrò, G.; Sips, A.C.C.; Maggi, C.F.; De Tommasi, G.M.; Joffrin, E.; Loarte, A.; Maviglia, F.; Mlynář, Jan; Rimini, F.G.; Pütterich, T.

2015-01-01

Roč. 55, č. 1 (2015), 013009-013009 ISSN 0029-5515 Institutional support: RVO:61389021 Keywords : tokamak * ramp-up * JET * ITER Subject RIV: BL - Plasma and Gas Discharge Physics Impact factor: 4.040, year: 2015 http://iopscience.iop.org/article/10.1088/0029-5515/55/1/013009#metrics

Portion sizes and obesity: responses of fast-food companies.

Science.gov (United States)

Young, Lisa R; Nestle, Marion

2007-07-01

Because the sizes of food portions, especially of fast food, have increased in parallel with rising rates of overweight, health authorities have called on fast-food chains to decrease the sizes of menu items. From 2002 to 2006, we examined responses of fast-food chains to such calls by determining the current sizes of sodas, French fries, and hamburgers at three leading chains and comparing them to sizes observed in 1998 and 2002. Although McDonald's recently phased out its largest offerings, current items are similar to 1998 sizes and greatly exceed those offered when the company opened in 1955. Burger King and Wendy's have increased portion sizes, even while health authorities are calling for portion size reductions. Fast-food portions in the United States are larger than in Europe. These observations suggest that voluntary efforts by fast-food companies to reduce portion sizes are unlikely to be effective, and that policy approaches are needed to reduce energy intake from fast food.

The significance of biometric parameters in determining anterior teeth width

Directory of Open Access Journals (Sweden)

Strajnić Ljiljana

2013-01-01

Full Text Available Background/Aim. An important element of prosthetic treatment of edentulous patients is selecting the size of anterior artificial teeth that will restore the natural harmony of one’s dentolabial structure as well as the whole face. The main objective of this study was to determine the correlation between the inner canthal distance (ICD and interalar width (IAW on one side and the width of both central incisors (CIW, the width of central and lateral incisors (CLIW, the width of anterior teeth (ATW, the width between the canine cusps (CCW, which may be useful in clinical practice. Methods. A total of 89 subjects comprising 23 male and 66 female were studied. Their age ranged from 19 to 34 years with the mean of 25 years. Only the subjects with the preserved natural dentition were included in the sample. All facial and intraoral tooth measurements were made with a Boley Gauge (Buffalo Dental Manufacturing Co., Brooklyn NY, USA having a resolution of 0.1mm. Results. A moderate correlation was established between the interalar width and combined width of anterior teeth and canine cusp width (r = 0.439, r = 0.374. A low correlation was established between the inner canthal distance and the width of anterior teeth and canine cusp width (r = 0.335, r = 0.303. The differences between the two genders were highly significant for all the parameters (p < 0.01. The measured facial distances and width of anterior teeth were higher in men than in women. Conclusion. The results of this study suggest that the examined interalar width and inner canthal distance cannot be considered reliable guidelines in the selection of artificial upper anterior teeth. However, they may be used as a useful additional factor combined with other methods for objective tooth selection. The final decision should be made while working on dentures fitting models with the patient’s consent.

Influence of the hold period on the fuel rod behaviour during a power ramp

International Nuclear Information System (INIS)

Bourreau, S.; Lansiart, S.; Couffin, P.; Verdeau, C.; Decroix, G.M.; Grandjean, M.-C.; Hugot, H.; Mermaz, F.; Van Schel, E.

2000-01-01

This paper presents three examples of power ramp tests performed in the OSIRIS experimental reactor, located at Saclay (France). The rods tested during these experiments stem from the same segmented 'mother' rod, pre-irradiated for two cycles in a French PWR. They underwent very similar power transient conditions, except for the hold time at Ramp Terminal Level (RTL) - respectively 41.5 kW/m (J12/2), 40.7 kW/m (J12/4) and 39.5 kW/m (J12/5) for RTL, but zero (J12/2), 16 minutes (J12/4) and 12 hours (J12/5) for the hold time at RTL. No failure was detected for any of the three experiments despite the relatively high mechanical stress applied to the cladding in the case of J12/2. Moreover, although no hold time was maintained at RTL, a permanent deformation clearly appeared on the clad during the power transient. An analysis of the cladding deformation has also been undertaken concerning the J12/2, J12/4 and J12/5 experiments. This study was realized by carrying out post-calculations of the three experiments with a 2D fuel modelling code using the finite element method. The computations satisfactorily reproduce the influence of hold time on the cladding deformation during the power transients, especially for the J12/2 and J12/4 experiments with hold times enclosing the failure times experimentally observed for power ramp tests. For the hold time of 12 hours, the micrographic observations of the fuel, compared to the case of the 16 minutes hold time, support the hypothesis of weak but noticeable gaseous swelling. (author)

The decay width of stringy hadrons

Directory of Open Access Journals (Sweden)

Jacob Sonnenschein

2018-02-01

We fit the theoretical decay width to experimental data for mesons on the trajectories of ρ, ω, π, η, K⁎, ϕ, D, and Ds⁎, and of the baryons N, Δ, Λ, and Σ. We examine both the linearity in L and the exponential suppression factor. The linearity was found to agree with the data well for mesons but less for baryons. The extracted coefficient for mesons A=0.095±0.015 is indeed quite universal. The exponential suppression was applied to both strong and radiative decays. We discuss the relation with string fragmentation and jet formation. We extract the quark–diquark structure of baryons from their decays. A stringy mechanism for Zweig suppressed decays of quarkonia is proposed and is shown to reproduce the decay width of ϒ states. The dependence of the width on spin and flavor symmetry is discussed. We further apply this model to the decays of glueballs and exotic hadrons.

Intraflow width variations in Martian and terrestrial lava flows

Science.gov (United States)

Peitersen, Matthew N.; Crown, David A.

1997-03-01

Flow morphology is used to interpret emplacement processes for lava flows on Earth and Mars. Accurate measurements of flow geometry are essential, particularly for planetary flows where neither compositional sampling nor direct observations of active flows may be possible. Width behavior may indicate a flow's response to topography, its emplacement regime, and its physical properties. Variations in width with downflow distance from the vent may therefore provide critical clues to flow emplacement processes. Flow width is also one of the few characteristics that can be readily measured from planetary mission data with accuracy. Recent analyses of individual flows at two terrestrial and four Martian sites show that widths within an individual flow vary by up to an order of magnitude. Width is generally thought to be correlated to topography; however, recent studies show that this relationship is neither straightforward nor easily quantifiable.

A Data-Driven Control Design Approach for Freeway Traffic Ramp Metering with Virtual Reference Feedback Tuning

Directory of Open Access Journals (Sweden)

Shangtai Jin

2014-01-01

Full Text Available ALINEA is a simple, efficient, and easily implemented ramp metering strategy. Virtual reference feedback tuning (VRFT is most suitable for many practical systems since it is a “one-shot” data-driven control design methodology. This paper presents an application of VRFT to a ramp metering problem of freeway traffic system. When there is not enough prior knowledge of the controlled system to select a proper parameter of ALINEA, the VRFT approach is used to optimize the ALINEA's parameter by only using a batch of input and output data collected from the freeway traffic system. The extensive simulations are built on both the macroscopic MATLAB platform and the microscopic PARAMICS platform to show the effectiveness and applicability of the proposed data-driven controller tuning approach.

Analysis and control of chaotic behavior in boost converter by ramp compensation based on Lyapunov exponents assignment: theoretical and experimental investigation

International Nuclear Information System (INIS)

Zamani, Najmeh; Ataei, Mohammad; Niroomand, Mehdi

2015-01-01

Highlights: • Applying nonlinear analysis of complex dynamics displayed by current-mode controlled boost converter. • The ramp compensation method is used to control bifurcation and chaos in these converters based on bifurcation diagram and Lyapunov exponents assignment. • A discrete-time iterative nonlinear mapping model has been derived by inserting the ramp compensation parameter in the dynamical equations of the system. • A design methodology for chaos control is provided in this converter based on Lyapunov exponents assignment in desired values theoretically by proper selection of compensator slope. • Practical results are provided to confirm the theoretical analysis and simulations. - Abstract: Nonlinear analysis of complex dynamics displayed by current mode dc–dc converter and idea of Lyapunov exponents assignment by ramp compensator in order to control chaotic behavior is proposed in this article. A discrete-time iterative nonlinear mapping model is derived. The occurrence of the complex behaviors of bifurcation and chaos generated by varying the circuit parameters are investigated through numerical analysis and software implementation of the circuit. Next, in order to control bifurcation and chaos in these converters, the ramp compensation method is used. By inserting the ramp compensation parameter in the dynamical equations of the system, these complex behaviors are examined theoretically and numerically as well. It is proved that through this method, the stable period-one operation of the converter can be extended. By evaluating the Lyapunov exponents (LEs) of the system, the impact of the slope on the location of LEs are determined analytically. This leads to a design methodology for control of chaos in this converter based on LEs assignment in desired values by proper selection of compensator slope. By developing an experimental set up, practical results are obtained to confirm the theoretical analysis and simulations.

Heart Rate Variability as a Measure of Airport Ramp-Traffic Controllers Workload

Science.gov (United States)

Hayashi, Miwa; Dulchinos, Victoria Lee

2016-01-01

Heart Rate Variability (HRV) has been reported to reflect the person's cognitive and emotional stress levels, and may offer an objective measure of human-operator's workload levels, which are recorded continuously and unobtrusively to the task performance. The present paper compares the HRV data collected during a human-in-the-loop simulation of airport ramp-traffic control operations with the controller participants' own verbal self-reporting ratings of their workload.

The Tool Life of Ball Nose end Mill Depending on the Different Types of Ramping

Directory of Open Access Journals (Sweden)

Vopát Tomáš

2014-12-01

Full Text Available The article deals with the cutting tool wear measurement process and tool life of ball nose end mill depending on upward ramping and downward ramping. The aim was to determine and compare the wear (tool life of ball nose end mill for different types of copy milling operations, as well as to specify particular steps of the measurement process. In addition, we examined and observed cutter contact areas of ball nose end mill with machined material. For tool life test, DMG DMU 85 monoBLOCK 5-axis CNC milling machine was used. In the experiment, cutting speed, feed rate, axial depth of cut and radial depth of cut were not changed. The cutting tool wear was measured on Zoller Genius 3s universal measuring machine. The results show different tool life of ball nose end mills depending on the copy milling strategy.

Crack widths in concrete with fibers and main reinforcement

DEFF Research Database (Denmark)

Christensen, Frede; Ulfkjær, Jens Peder; Brincker, Rune

2015-01-01

The main object of the research work presented in this paper is to establish design tools for concrete structures where main reinforcement is combined with addition of short discrete steel fibers. The work is concerned with calculating and measuring crack widths in structural elements subjected...... to bending load. Thus, the aim of the work is to enable engineers to calculate crack widths for flexural concrete members and analyze how different combinations of amounts of fibers and amounts of main reinforcement can meet a given maximum crack width requirement. A mathematical model including...... the ductility of the fiber reinforced concrete (FRC) is set up and experimental work is conducted in order to verify the crack width model. The ductility of the FRC is taken into account by using the stress crack width relation. The constitutive model for the FRC is based on the idea that the initial part...

Relation Between Pressure and Volume Unloading During Ramp Testing in Patients Supported with a Continuous-Flow Left Ventricular Assist Device

DEFF Research Database (Denmark)

Jung, Mette H; Hassager, Christian; Balling, Louise

2015-01-01

Pulmonary capillary wedge pressure (PCWP) is the key to describing left ventricular (LV) unloading, however, the relation between pressure and the echocardiography-derived surrogate of LV volume (left ventricular end-diastolic diameter (LVEDD)) as a function of pump speed (RPM) in continuous......-flow left ventricular assist device (CF-LVAD) patients is unknown. In this study the pressure-volume relationship as a function of RPM during ramp testing was investigated by simultaneously measuring PCWP by Swan-Ganz catheter and LVEDD by echocardiography. The ramp protocol started at usual pump setting...

Food photography. I: The perception of food portion size from photographs.

Science.gov (United States)

Nelson, M; Atkinson, M; Darbyshire, S

1994-11-01

Fifty-one male and female volunteers aged 18-90 years from a wide variety of social and occupational backgrounds completed 7284 assessments of portion size in relation to food photographs. Subjects were shown six portion sizes (two small, two medium and two large) for each of six foods, and asked to compare the amount on the plate in front of them to (a) a series of eight photographs showing weights of portions from the 5th to the 95th centile of portion size (British Adult Dietary Survey), or (b) a single photograph of the average (median) portion size. Photographs were prepared either in colour or in black and white, and in two different sizes. The order of presentation of foods; use of black and white or colour; the size of photographs; and presentation of eight or average photographs were each randomized independently. On average, the mean differences between the portion size presented and the estimate of portion size using the photographs varied from -8 to +6 g (-4 to +5%) for the series of eight photographs, and from -34 to -1 g (-23 to +9%) for the single average photograph. Large portion sizes tended to be underestimated more than medium or small portion sizes, especially when using the average photograph (from -79 to -14 g, -37 to -13%). Being female, 65 years and over, or retired, or seeing photographs in colour, were all associated with small but statistically significant overestimations of portion size. Having a body mass index > or = 30 kg/m2 was associated with an 8% underestimate of portion size. We conclude that use of a series of eight photographs is associated with relatively small errors in portion size perception, whereas use of an average photograph is consistently associated with substantial underestimation across a variety of foods.

Large Portions Encourage the Selection of Palatable Rather Than Filling Foods.

Science.gov (United States)

Brunstrom, Jeffrey M; Jarvstad, Andreas; Griggs, Rebecca L; Potter, Christina; Evans, Natalie R; Martin, Ashley A; Brooks, Jon Cw; Rogers, Peter J

2016-10-01

Portion size is an important driver of larger meals. However, effects on food choice remain unclear. Our aim was to identify how portion size influences the effect of palatability and expected satiety on choice. In Study 1, adult participants (n = 24, 87.5% women) evaluated the palatability and expected satiety of 5 lunchtime meals and ranked them in order of preference. Separate ranks were elicited for equicaloric portions from 100 to 800 kcal (100-kcal steps). In Study 2, adult participants (n = 24, 75% women) evaluated 9 meals and ranked 100-600 kcal portions in 3 contexts (scenarios), believing that 1) the next meal would be at 1900, 2) they would receive only a bite of one food, and 3) a favorite dish would be offered immediately afterwards. Regression analysis was used to quantify predictors of choice. In Study 1, the extent to which expected satiety and palatability predicted choice was highly dependent on portion size (P palatability (100-kcal portions: expected satiety, β: 0.42; palatability, β: 0.46). With larger portions, palatability was a strong predictor (600-kcal portions: β: 0.53), and expected satiety was a poor or negative predictor (600-kcal portions: β: -0.42). In Study 2, this pattern was moderated by context (P = 0.024). Results from scenario 1 replicated Study 1. However, expected satiety was a poor predictor in both scenario 2 (expected satiety was irrelevant) and scenario 3 (satiety was guaranteed), and palatability was the primary driver of choice across all portions. In adults, expected satiety influences food choice, but only when small equicaloric portions are compared. Larger portions not only promote the consumption of larger meals, but they encourage the adoption of food choice strategies motivated solely by palatability. © 2016 American Society for Nutrition.

Bounding the Higgs boson width through interferometry.

Science.gov (United States)

Dixon, Lance J; Li, Ye

2013-09-13

We study the change in the diphoton-invariant-mass distribution for Higgs boson decays to two photons, due to interference between the Higgs resonance in gluon fusion and the continuum background amplitude for gg→γγ. Previously, the apparent Higgs mass was found to shift by around 100 MeV in the standard model in the leading-order approximation, which may potentially be experimentally observable. We compute the next-to-leading-order QCD corrections to the apparent mass shift, which reduce it by about 40%. The apparent mass shift may provide a way to measure, or at least bound, the Higgs boson width at the Large Hadron Collider through "interferometry." We investigate how the shift depends on the Higgs width, in a model that maintains constant Higgs boson signal yields. At Higgs widths above 30 MeV, the mass shift is over 200 MeV and increases with the square root of the width. The apparent mass shift could be measured by comparing with the ZZ* channel, where the shift is much smaller. It might be possible to measure the shift more accurately by exploiting its strong dependence on the Higgs transverse momentum.

Optimization design of energy deposition on single expansion ramp nozzle

Science.gov (United States)

Ju, Shengjun; Yan, Chao; Wang, Xiaoyong; Qin, Yupei; Ye, Zhifei

2017-11-01

Optimization design has been widely used in the aerodynamic design process of scramjets. The single expansion ramp nozzle is an important component for scramjets to produces most of thrust force. A new concept of increasing the aerodynamics of the scramjet nozzle with energy deposition is presented. The essence of the method is to create a heated region in the inner flow field of the scramjet nozzle. In the current study, the two-dimensional coupled implicit compressible Reynolds Averaged Navier-Stokes and Menter's shear stress transport turbulence model have been applied to numerically simulate the flow fields of the single expansion ramp nozzle with and without energy deposition. The numerical results show that the proposal of energy deposition can be an effective method to increase force characteristics of the scramjet nozzle, the thrust coefficient CT increase by 6.94% and lift coefficient CN decrease by 26.89%. Further, the non-dominated sorting genetic algorithm coupled with the Radial Basis Function neural network surrogate model has been employed to determine optimum location and density of the energy deposition. The thrust coefficient CT and lift coefficient CN are selected as objective functions, and the sampling points are obtained numerically by using a Latin hypercube design method. The optimized thrust coefficient CT further increase by 1.94%, meanwhile, the optimized lift coefficient CN further decrease by 15.02% respectively. At the same time, the optimized performances are in good and reasonable agreement with the numerical predictions. The findings suggest that scramjet nozzle design and performance can benefit from the application of energy deposition.

Hanford facility dangerous waste permit application, general information portion

International Nuclear Information System (INIS)

Hays, C.B.

1998-01-01

The Hanford Facility Dangerous Waste Permit Application is considered to be a single application organized into a General Information Portion (document number DOE/RL-91-28) and a Unit-Specific Portion. Both the General Information and Unit-Specific portions of the Hanford Facility Dangerous Waste Permit Application address the content of the Part B permit application guidance prepared by the Washington State Department of Ecology (Ecology 1996) and the U.S. Environmental Protection Agency (40 Code of Federal Regulations 270), with additional information needed by the Hazardous and Solid Waste Amendments and revisions of Washington Administrative Code 173-303. Documentation contained in the General Information Portion is broader in nature and could be used by multiple treatment, storage, and/or disposal units (e.g., the glossary provided in this report)

Flux consumption, current ramp-up and current diffusion in Tore Supra non-inductive Lower Hybrid scenarios

International Nuclear Information System (INIS)

Kazarian, F.; Litaudon, X.; Moreau, D.; Arslanbekov, R.; Hoang, G.T.; Joffrin, E.; Peysson, Y.; Allibert, J.P.; Ane, J.M.; Bremond, S.

1995-01-01

The main objective of the Lower Hybrid (LH) experiments performed on Tore Supra is to provide large flux savings for long pulse operation while controlling the plasma current density profile. This goal will be best achieved by applying LH wave directly during the current ramp-up phase. Experiments have been performed where a large fraction of the current is driven non-inductively during the ramp-up phase. A theoretical flux consumption scaling is presented and compared to experimental data. The time evolutions of the current density profiles are analysed with a new current diffusion code (CRONOS). In view to achieve fully non-inductive current drive discharges in a fast, systematic and reproducible way, experiments where the primary voltage is imposed have been carried out. In a complementary approach, an appropriate transformer flux feedback scheme has been also studied. (author) 6 refs.; 6 figs

Meson widths from string worldsheet instantons

International Nuclear Information System (INIS)

Faulkner, Thomas; Liu, Hong

2009-01-01

We show that open strings living on a D-brane which lies outside an AdS black hole can tunnel into the black hole through worldsheet instantons. These instantons have a simple interpretation in terms of thermal quarks in the dual Yang-Mills (YM) theory. As an application we calculate the width of a meson in a strongly coupled quark-gluon plasma which is described holographically as a massless mode on a D7 brane in AdS 5 xS 5 . While the width of the meson is zero to all orders in the 1/√(λ) expansion with λ the 't Hooft coupling, it receives non-perturbative contributions in 1/√(λ) from worldsheet instantons. We find that the width increases quadratically with momentum at large momentum and comment on potential phenomenological implications of this enhancement for heavy ion collisions. We also comment on how this non-perturbative effect has important consequences for the phase structure of the YM theory obtained in the classical gravity limit

Gap Width Study and Fixture Design in Laser Butt-Welding

DEFF Research Database (Denmark)

Gong, Hui; Olsen, Flemming Ove

.5-2.0 m/min, the laser power : 2 and 2.6 kW and the focal point position : 0 and -1.2 mm. Quality of all the butt welds are destructively tested according to ISO 13919-1.Influences of the variable process parameters to the maximum allowable gap width are observed as (1) the maximum gap width is inversely......This paper discusses some practical consideration for design of a mechanical fixture, which enables to accurately measure the width of a gap between two stainless steel workpieces and to steadfastly clamp the workpieces for butt-welding with a high power CO2 laser.With such a fixture, a series...... of butt-welding experiment is successfully carried out in order to find the maximum allowable gap width in laser butt-welding. The gap width study (GWS) is performed on the material of SST of W1.4401 (AISI 316) under various welding conditions, which are the gap width : 0.00-0.50 mm, the welding speed : 0...

Applied Distributed Model Predictive Control for Energy Efficient Buildings and Ramp Metering

Science.gov (United States)

Koehler, Sarah Muraoka

suited for nonlinear optimization problems. The parallel computation of the algorithm exploits iterative linear algebra methods for the main linear algebra computations in the algorithm. We show that the splitting of the algorithm is flexible and can thus be applied to various distributed platform configurations. The two proposed algorithms are applied to two main energy and transportation control problems. The first application is energy efficient building control. Buildings represent 40% of energy consumption in the United States. Thus, it is significant to improve the energy efficiency of buildings. The goal is to minimize energy consumption subject to the physics of the building (e.g. heat transfer laws), the constraints of the actuators as well as the desired operating constraints (thermal comfort of the occupants), and heat load on the system. In this thesis, we describe the control systems of forced air building systems in practice. We discuss the "Trim and Respond" algorithm which is a distributed control algorithm that is used in practice, and show that it performs similarly to a one-step explicit DMPC algorithm. Then, we apply the novel distributed primal-dual active-set method and provide extensive numerical results for the building MPC problem. The second main application is the control of ramp metering signals to optimize traffic flow through a freeway system. This application is particularly important since urban congestion has more than doubled in the past few decades. The ramp metering problem is to maximize freeway throughput subject to freeway dynamics (derived from mass conservation), actuation constraints, freeway capacity constraints, and predicted traffic demand. In this thesis, we develop a hybrid model predictive controller for ramp metering that is guaranteed to be persistently feasible and stable. This contrasts to previous work on MPC for ramp metering where such guarantees are absent. We apply a smoothing method to the hybrid model predictive

Analysis of stationary fuel cell dynamic ramping capabilities and ultra capacitor energy storage using high resolution demand data

Science.gov (United States)

Meacham, James R.; Jabbari, Faryar; Brouwer, Jacob; Mauzey, Josh L.; Samuelsen, G. Scott

Current high temperature fuel cell (HTFC) systems used for stationary power applications (in the 200-300 kW size range) have very limited dynamic load following capability or are simply base load devices. Considering the economics of existing electric utility rate structures, there is little incentive to increase HTFC ramping capability beyond 1 kWs -1 (0.4% s -1). However, in order to ease concerns about grid instabilities from utility companies and increase market adoption, HTFC systems will have to increase their ramping abilities, and will likely have to incorporate electrical energy storage (EES). Because batteries have low power densities and limited lifetimes in highly cyclic applications, ultra capacitors may be the EES medium of choice. The current analyses show that, because ultra capacitors have a very low energy storage density, their integration with HTFC systems may not be feasible unless the fuel cell has a ramp rate approaching 10 kWs -1 (4% s -1) when using a worst-case design analysis. This requirement for fast dynamic load response characteristics can be reduced to 1 kWs -1 by utilizing high resolution demand data to properly size ultra capacitor systems and through demand management techniques that reduce load volatility.

Container size influences snack food intake independently of portion size.

Science.gov (United States)

Marchiori, David; Corneille, Olivier; Klein, Olivier

2012-06-01

While larger containers have been found to increase food intake, it is unclear whether this effect is driven by container size, portion size, or their combination, as these variables are usually confounded. The study was advertised as examining the effects of snack food consumption on information processing and participants were served M&M's for free consumption in individual cubicles while watching a TV show. Participants were served (1) a medium portion of M&M's in a small (n=30) or (2) in a large container (n=29), or (3) a large portion in a large container (n=29). The larger container increased intake by 129% (199 kcal) despite holding portion size constant, while controlling for different confounding variables. This research suggests that larger containers stimulate food intake over and above their impact on portion size. Copyright © 2012 Elsevier Ltd. All rights reserved.

A Middle Triassic pachypleurosaur (Diapsida: Eosauropterygia) from a restricted carbonate ramp in the Western Carpathians (Gutenstein Formation, Fatric Unit): paleogeographic implications

Science.gov (United States)

Čerňanský, Andrej; Klein, Nicole; Soták, Ján; Olšavský, Mário; Šurka, Juraj; Herich, Pavel

2018-02-01

An eosauropterygian skeleton found in the Middle Triassic (upper Anisian) Gutenstein Formation of the Fatric Unit (Demänovská dolina Valley, Low Tatra Mountains, Slovakia) represents the earliest known occurrence of marine tetrapods in the Western Carpathians. The specimen represents a partly articulated portion of the postcranial skeleton (nine dorsal vertebrae, coracoid, ribs, gastral ribs, pelvic girdle, femur and one zeugopodial element). It is assigned to the Pachypleurosauria, more precisely to the Serpianosaurus-Neusticosaurus clade based on the following combination of features: (1) small body size; (2) morphology of vertebrae, ribs and femur; (3) tripartite gastral ribs; and (4) microanatomy of the femur as revealed by μCT. Members of this clade were described from the epicontinental Germanic Basin and the Alpine Triassic (now southern Germany, Switzerland, Italy), and possibly from Spain. This finding shows that pachypleurosaur reptiles attained a broader geographical distribution during the Middle Triassic, with their geographical range reaching to the Central Western Carpathians. Pachypleurosaurs are often found in sediments formed in shallow, hypersaline carbonate-platform environments. The specimen found here occurs in a succession with vermicular limestones in a shallow subtidal zone and stromatolitic limestones in a peritidal zone, indicating that pachypleurosaurs inhabited hypersaline, restricted carbonate ramps in the Western Carpathians.

A Middle Triassic pachypleurosaur (Diapsida: Eosauropterygia from a restricted carbonate ramp in the Western Carpathians (Gutenstein Formation, Fatric Unit: paleogeographic implications

Directory of Open Access Journals (Sweden)

Čerňanský Andrej

2018-02-01

Full Text Available An eosauropterygian skeleton found in the Middle Triassic (upper Anisian Gutenstein Formation of the Fatric Unit (Demänovská dolina Valley, Low Tatra Mountains, Slovakia represents the earliest known occurrence of marine tetrapods in the Western Carpathians. The specimen represents a partly articulated portion of the postcranial skeleton (nine dorsal vertebrae, coracoid, ribs, gastral ribs, pelvic girdle, femur and one zeugopodial element. It is assigned to the Pachypleurosauria, more precisely to the Serpianosaurus–Neusticosaurus clade based on the following combination of features: (1 small body size; (2 morphology of vertebrae, ribs and femur; (3 tripartite gastral ribs; and (4 microanatomy of the femur as revealed by μCT. Members of this clade were described from the epicontinental Germanic Basin and the Alpine Triassic (now southern Germany, Switzerland, Italy, and possibly from Spain. This finding shows that pachypleurosaur reptiles attained a broader geographical distribution during the Middle Triassic, with their geographical range reaching to the Central Western Carpathians. Pachypleurosaurs are often found in sediments formed in shallow, hypersaline carbonate-platform environments. The specimen found here occurs in a succession with vermicular limestones in a shallow subtidal zone and stromatolitic limestones in a peritidal zone, indicating that pachypleurosaurs inhabited hypersaline, restricted carbonate ramps in the Western Carpathians.

Stream Width Dynamics in a Small Headwater Catchment

Science.gov (United States)

Barefoot, E. A.; Pavelsky, T.; Allen, G. H.; Zimmer, M. A.; McGlynn, B. L.

2016-12-01

Changing streamflow conditions cause small, ephemeral and intermittent stream networks to expand and contract, while simultaneously driving widening and narrowing of streams. The resulting dynamic surface area of ephemeral streams impacts critical hydrological and biogeochemical processes, including air-water gas exchange, solute transport, and sediment transport. Despite the importance of these dynamics, to our knowledge there exists no complete study of how stream widths vary throughout an entire catchment in response to changing streamflow conditions. Here we present the first characterization of how variable hydrologic conditions impact the distribution of stream widths in a 48 ha headwater catchment in the Stony Creek Research Watershed, NC, USA. We surveyed stream widths longitudinally every 5 m on 12 occasions over a range of stream discharge from 7 L/s to 128 L/s at the catchment outlet. We hypothesize that the shape and location of the stream width distribution are driven by the action of two interrelated mechanisms, network extension and at-a-station widening, both of which increase with discharge. We observe that during very low flow conditions, network extension more significantly influences distribution location, and during high flow conditions stream widening is the dominant driver. During moderate flows, we observe an approximately 1 cm rightward shift in the distribution peak with every additional 10 L/s of increased discharge, which we attribute to a greater impact of at-a-station widening on distribution location. Aside from this small shift, the qualitative location and shape of the stream width distribution are largely invariant with changing streamflow. We suggest that the basic characteristics of stream width distributions constitute an equilibrium between the two described mechanisms across variable hydrologic conditions.

Current ramp-up experiments in full current drive plasmas on TRIAM-1M

International Nuclear Information System (INIS)

Hanada, K.; Nakamura, K.; Hasegawa, M.

2003-01-01

Four types of plasma current ramp-up experiments were executed on TRIAM-1M in full lower hybrid current drive plasmas (LHCD: 8.2GHz, up to 0.4 MW, 8 x 2 grill antenna); 1) the current start up by the combination between electron cyclotron resonance heating (ECH: 170GHz, up to 0.2 MW, O-mode launching) and LHCD at the density of ∼2x10 19 m -3 at B t =6.7T, 2) the tail heating by the additional LHCD, 3) the bulk heating by ECH, 4) the spontaneous ramp up by the transition to enhanced current drive (ECD) mode. The time evolutions of plasma current during four types of ramp-up phase were investigated and an exponential type and a tangent-hyperbolic one were observed. The time evolutions of plasma current during the tail and the bulk heating show the exponential type except the tail heating with high n parallel and it has a tangent-hyperbolic one during the ECD mode and the current start-up. A simple model with two different time constants, which are a time defined by L/R, τ L/R , and a time caused by change of the effective refractive index along the magnetic field, τ, is proposed to explain two types of the time evolution of the plasma current. The estimated τ L/R is consistent with the calculated one from the plasma parameter. It is found that τ are less than τ L/R in the cases of the tail and the bulk heating, and comparable in the cases of the ECD mode, and more than τ L/R in the cases of the plasma start-up. This indicates that the value of the effective refractive index along the magnetic field, parallel >, develops during the ECD mode and the current start-up. The value of τ depends on the RF power. The estimated is close to the expected up-shifted n parallel due to the toroidal effect and the magnetic shear. (author)

Transfer hood for handling fuel assemblies in nuclear reactors and especially fast reactors

International Nuclear Information System (INIS)

Aubert, M.; Merland, D.; Renaux, C.

1975-01-01

A description is given of a hood for transferring fuel assemblies between two or more separate guide ramps inclined to the vertical at the same angle of slope and extending respectively through a first passage into the reactor vessel and through a second passage into a fuel-assembly storage chamber. The hood comprises at least one shielded duct joined to a flanged rotating portion which is so arranged that the open lower end of the shielded duct is positioned in the line of extension of one guide ramp and then the other as a result of displacement of the rotating portion

Experimental Study of Reversed Shear Alfven Eigenmodes During The Current Ramp In The Alcator C-Mod Tokamak

International Nuclear Information System (INIS)

Edlund, E.M.; Porkolab, M.; Kramer, G.J.; Lin, L.; Lin, Y.; Tsuji, N.; Wukitch, S.J.

2010-01-01

Experiments conducted in the Alcator C-Mod tokamak at MIT have explored the physics of reversed shear Alfven eigenmodes (RSAEs) during the current ramp. The frequency evolution of the RSAEs throughout the current ramp provides a constraint on the evolution of q min , a result which is important in transport modeling and for comparison with other diagnostics which directly measure the magnetic field line structure. Additionally, a scaling of the RSAE minimum frequency with the sound speed is used to derive a measure of the adiabatic index, a measure of the plasma compressibility. This scaling bounds the adiabatic index at 1.40 ± 0.15 used in MHD models and supports the kinetic calculation of separate electron and ion compressibilities with an ion adiabatic index close to 7/4.

Identification of anomalous Doppler resonance effect during current ramp down in HT-7 tokamak

Energy Technology Data Exchange (ETDEWEB)

Li Erzhong, E-mail: rzhonglee@ipp.ac.c [Institute of Plasma Physics, Chinese Academy of Science, Hefei 230031 (China); Hu Liqun; Ling Bili; Liu Yong; Ti Ang; Zhou Reijie; Lu Hongwei; Gao Xiang [Institute of Plasma Physics, Chinese Academy of Science, Hefei 230031 (China)

2010-09-21

The abrupt steep jump of electron cyclotron emission (ECE) signals during current ramp-down has been observed and explained by an anomalous Doppler resonance effect (ADR). The identifying process of ADR was presented based on the fast Fourier transform (FFT) technique. The threshold value for triggering a steep jump on ECE signals has been identified under different discharge conditions.

Non-inductive plasma initiation and plasma current ramp-up on the TST-2 spherical tokamak

International Nuclear Information System (INIS)

Takase, Y.; Ejiri, A.; Oosako, T.; Shinya, T.; Ambo, T.; Furui, H.; Kato, K.; Nakanishi, A.; Sakamoto, T.; Kakuda, H.; Wakatsuki, T.; Hashimoto, T.; Hiratsuka, J.; Kasahara, H.; Kumazawa, R.; Mutoh, T.; Saito, K.; Seki, T.; Moeller, C.P.; Nagashima, Y.

2013-01-01

Plasma current (I p ) start-up in a spherical tokamak (ST) by waves in the lower-hybrid (LH) frequency range was investigated on TST-2. A low current (∼1 kA) ST configuration can be formed by waves over a broad frequency range (21 MHz–8.2 GHz in TST-2), but further I p ramp-up (to ∼10 kA) is most efficient with waves in the LH frequency range. I p ramp-up to 15 kA was achieved with 60 kW of net RF power P RF in the fast wave (FW) polarization at 200 MHz excited by the inductively coupled combline antenna. X-ray measurements showed that the photon flux and temperature are higher in the direction opposite to I p , consistent with acceleration of electrons by a uni-directional RF wave. There is evidence that the LH wave is excited nonlinearly by the FW, based on the frequency spectra measured by magnetic probes. Similar efficiencies of I p ramp-up were obtained with the inductive combline antenna and the dielectric-loaded waveguide array (‘grill’) antenna, and tendencies for the current drive efficiency to increase with plasma current and toroidal field were observed. During operation of the grill antenna, wavevector components were measured by an array of magnetic probes. Results were qualitatively consistent with expectations based on dispersion relations for the FW and the LH wave. A capacitively coupled combline antenna has been developed to improve coupling to the plasma and the wavenumber spectrum of the excited LH wave, and will be tested in 2013. (paper)

Measuring modulated luminescence using non-modulated stimulation: Ramping the sample period

DEFF Research Database (Denmark)

Poolton, N.R.J.; Bøtter-Jensen, L.; Andersen, C.E.

2003-01-01

. Directly analogous results to LM-OSL can, however, be achieved with non-modulated excitation sources, by ramping the sample period (RSP) of luminescence detection. RSP-OSL has the distinct advantage over LM-OSL in that, since the excitation remains at full power, data accumulation times (that can...... be considerable) can be reduced by typically 50%. RSP methods are universally applicable and can be employed, for example, where the excitation source is constant heat, rather than light: here, iso-thermal decay of phosphorescence becomes recorded as a sequence of peaks, corresponding to de-trapping of charge...

Human subjects’ perception of indoor environment and their office work performance during exposures to moderate operative temperature ramps

DEFF Research Database (Denmark)

Kolarik, Jakub; Toftum, Jørn; Olesen, Bjarne W.

2008-01-01

The objective of the presented research work was to study the effects of moderate operative temperature drifts on human thermal comfort, perceived air quality, intensity of SBS symptoms and office work performance. Experimental subjects (52, 50% female) were seated in a climatic chamber and exposed....... A linear relation between perceived air quality and temperature (enthalpy) was found. No significant consistent effect of individual temperature ramps on office work performance was found. Increasing operative temperature appeared to slightly decrease speed of addition and text typing regardless the slope...... sensation was also included. Subjects filled out questionnaires regarding perception of the environment and intensity of SBS symptoms. Subjects performed simulated office tasks (addition, text typing, proof reading, comprehension and reasoning). Results showed that all tested ramps were recognized...

The pack size effect: Influence on consumer perceptions of portion sizes

NARCIS (Netherlands)

Hieke, Sophie; Palascha, Aikaterini; Jola, Corinne; Wills, Josephine; Raats, Monique M.

2016-01-01

Larger portions as well as larger packs can lead to larger prospective consumption estimates, larger servings and increased consumption, described as 'portion-size effects' and 'pack size effects'. Although related, the effects of pack sizes on portion estimates have received less attention. While

Dynamic behaviors of a Zr-based bulk metallic glass under ramp wave and shock wave loading

Directory of Open Access Journals (Sweden)

Binqiang Luo

2015-06-01

Full Text Available Dynamic behaviors of Zr51Ti5Ni10Cu25Al9 bulk metallic glass were investigated using electric gun and magnetically driven isentropic compression device which provide shock and ramp wave loading respectively. Double-wave structure was observed under shock compression while three-wave structure was observed under ramp compression in 0 ∼ 18GPa. The HEL of Zr51Ti5Ni10Cu25Al9 is 8.97 ± 0.61GPa and IEL is 8.8 ± 0.3GPa, respectively. Strength of Zr51Ti5Ni10Cu25Al9 estimated from HEL is 5.0 ± 0.3GPa while the strength estimated from IEL is 3.6 ± 0.1GPa. Shock wave velocity versus particle velocity curve of Zr51Ti5Ni10Cu25Al9 under shock compression appears to be bilinear and a kink appears at about 18GPa. The Lagrangian sound speed versus particle velocity curve of Zr51Ti5Ni10Cu25Al9 under ramp wave compression exhibits two discontinuances and are divided to three regions: elastic, plastic-I and plastic-II. The first jump-down occurs at elastic-plastic transition and the second appears at about 17GPa. In elastic and plastic-I regions, Lagrangian sound speed increases linearly with particle velocity, respectively. Characteristic response of sound speed in plastic-I region disagree with shock result in the same pressure region(7GPa ∼ 18GPa, but is consistent with shock result at higher pressure(18-110GPa.

Widths of the atomic K-N7 levels

International Nuclear Information System (INIS)

Campbell, J.L.; Papp, Tibor

2001-01-01

Atomic level widths obtained from experimental measurements are collected in Table I, along with the corresponding theoretical widths derived from the Evaluated Atomic Data Library (EADL) of Lawrence Livermore National Laboratory; these EADL values are based upon the Dirac-Hartree-Slater version of the independent-particle model. In a minority of cases, many-body theory predictions are also provided. A brief discussion of the manner in which the experimental widths were deduced from spectroscopic data is included. The bulk of the data are for elements in the solid state, but a few data for gases and simple compounds are included. For the K, L2, L3, and M5 levels, where Coster-Kronig contributions do not contribute or contribute only to a small extent to the overall widths, the EADL predictions appear satisfactory for elements in the solid state. For other levels, where Coster-Kronig and super-Coster-Kronig transitions have large probabilities within the independent-particle model, this model is not satisfactory. Table II provides a complete set of recommended elemental values based upon consideration of the available experimental data

Association between excess weight and beverage portion size consumed in Brazil

Directory of Open Access Journals (Sweden)

Ilana Nogueira Bezerra

2018-02-01

Full Text Available ABSTRACT OBJECTIVE To describe the beverage portion size consumed and to evaluate their association with excess weight in Brazil. METHODS We used data from the National Dietary Survey, which included individuals with two days of food record aged over 20 years (n = 24,527 individuals. The beverages were categorized into six groups: soft drink, 100% fruit juice, fruit drink, alcoholic beverage, milk, and coffee or tea. We estimated the average portion consumed for each group and we evaluated, using linear regression, the association between portion size per group and the variables of age, sex, income, and nutritional status. We tested the association between portion size and excess weight using Poisson regression, adjusted for age, sex, income, and total energy intake. RESULTS The most frequently consumed beverages in Brazil were coffee and tea, followed by 100% fruit juices, soft drinks, and milk. Alcoholic beverages presented the highest average in the portion size consumed, followed by soft drinks, 100% fruit juice, fruit drink, and milk. Portion size showed positive association with excess weight only in the soft drink (PR = 1.19, 95%CI 1.10–1.27 and alcoholic beverage groups (PR = 1.20, 95%CI, 1.11–1.29, regardless of age, sex, income, and total energy intake. CONCLUSIONS Alcoholic beverages and soft drinks presented the highest averages in portion size and positive association with excess weight. Public health interventions should address the issue of portion sizes offered to consumers by discouraging the consumption of large portions, especially sweetened and low nutritional beverages.

Estimation of portion size in children's dietary assessment: lessons learnt.

Science.gov (United States)

Foster, E; Adamson, A J; Anderson, A S; Barton, K L; Wrieden, W L

2009-02-01

Assessing the dietary intake of young children is challenging. In any 1 day, children may have several carers responsible for providing them with their dietary requirements, and once children reach school age, traditional methods such as weighing all items consumed become impractical. As an alternative to weighed records, food portion size assessment tools are available to assist subjects in estimating the amounts of foods consumed. Existing food photographs designed for use with adults and based on adult portion sizes have been found to be inappropriate for use with children. This article presents a review and summary of a body of work carried out to improve the estimation of portion sizes consumed by children. Feasibility work was undertaken to determine the accuracy and precision of three portion size assessment tools; food photographs, food models and a computer-based Interactive Portion Size Assessment System (IPSAS). These tools were based on portion sizes served to children during the National Diet and Nutrition Survey. As children often do not consume all of the food served to them, smaller portions were included in each tool for estimation of leftovers. The tools covered 22 foods, which children commonly consume. Children were served known amounts of each food and leftovers were recorded. They were then asked to estimate both the amount of food that they were served and the amount of any food leftover. Children were found to estimate food portion size with an accuracy approaching that of adults using both the food photographs and IPSAS. Further development is underway to increase the number of food photographs and to develop IPSAS to cover a much wider range of foods and to validate the use of these tools in a 'real life' setting.

The effects on grid matching and ramping requirements, of single and distributed PV systems employing various fixed and sun-tracking technologies

International Nuclear Information System (INIS)

Solomon, A.A.; Faiman, D.; Meron, G.

2010-01-01

In this second paper, which studies the hourly generation data from the Israel Electric Corporation for the year 2006, with a view to adding very large-scale photovoltaic power (VLS-PV) plants, three major extensions are made to the results reported in our first paper. In the first extension, PV system simulations are extended to include the cases of 1- and 2-axis sun-tracking, and 2-axis concentrator photovoltaic (CPV) technologies. Secondly, the effect of distributing VLS-PV plants among 8 Negev locations, for which hourly metrological data exist, is studied. Thirdly, in addition to studying the effect of VLS-PV on grid penetration, the present paper studies its effect on grid ramping requirements. The principal results are as follows: (i) sun-tracking improves grid matching at high but not low levels of grid flexibility; (ii) geographical distribution has little effect on grid penetration; (iii) VLS-PV significantly increases grid ramping requirements, particularly for CPV systems, but not beyond existing ramping capabilities; (iv) geographical distribution considerably ameliorates this effect.

Pulse Width Affects Scalp Sensation of Transcranial Magnetic Stimulation.

Science.gov (United States)

Peterchev, Angel V; Luber, Bruce; Westin, Gregory G; Lisanby, Sarah H

Scalp sensation and pain comprise the most common side effect of transcranial magnetic stimulation (TMS), which can reduce tolerability and complicate experimental blinding. We explored whether changing the width of single TMS pulses affects the quality and tolerability of the resultant somatic sensation. Using a controllable pulse parameter TMS device with a figure-8 coil, single monophasic magnetic pulses inducing electric field with initial phase width of 30, 60, and 120 µs were delivered in 23 healthy volunteers. Resting motor threshold of the right first dorsal interosseus was determined for each pulse width, as reported previously. Subsequently, pulses were delivered over the left dorsolateral prefrontal cortex at each of the three pulse widths at two amplitudes (100% and 120% of the pulse-width-specific motor threshold), with 20 repetitions per condition delivered in random order. After each pulse, subjects rated 0-to-10 visual analog scales for Discomfort, Sharpness, and Strength of the sensation. Briefer TMS pulses with amplitude normalized to the motor threshold were perceived as slightly more uncomfortable than longer pulses (with an average 0.89 point increase on the Discomfort scale for pulse width of 30 µs compared to 120 µs). The sensation of the briefer pulses was felt to be substantially sharper (2.95 points increase for 30 µs compared to 120 µs pulse width), but not stronger than longer pulses. As expected, higher amplitude pulses increased the perceived discomfort and strength, and, to a lesser degree the perceived sharpness. Our findings contradict a previously published hypothesis that briefer TMS pulses are more tolerable. We discovered that the opposite is true, which merits further study as a means of enhancing tolerability in the context of repetitive TMS. Copyright © 2016 Elsevier Inc. All rights reserved.

Theory of Feshbach molecule formation in a dilute gas during a magnetic field ramp

DEFF Research Database (Denmark)

Williams, J. E.; Nygaard, Nicolai; Clark, C. W.

2006-01-01

Starting with coupled atom-molecule Boltzmann equations, we develop a simplified model to understand molecule formation observed in recent experiments. Our theory predicts several key features: (1) the effective adiabatic rate constant is proportional to density; (2) in an adiabatic ramp...... show qualitative agreement with the data from [Hodby et al, Phys. Rev. Lett. 94, 120402 (2005)] without the use of adjustable parameters....

Temperature dependence of giant dipole resonance width

International Nuclear Information System (INIS)

Vdovin, A.I.; Storozhenko, A.N.

2005-01-01

The quasiparticle-phonon nuclear model extended to finite temperature within the framework of the thermo field dynamics is applied to calculate a temperature dependence of the spreading width Γ d own of a giant dipole resonance. Numerical calculations are made for 12S n and 208 Pb nuclei. It is found that the width Γ d own increases with T. The reason of this effect is discussed as well as a relation of the present approach to other ones existing in the literature

The Effects of Using a Ramp and Elevator to Load and Unload Trailers on the Behavior and Physiology of Piglets

Directory of Open Access Journals (Sweden)

John McGlone

2014-09-01

Full Text Available Transport is an inevitable process in the modern U.S. swine industry. The loading process is a novel and potentially stressful experience. This study uses behavior, heart rate and leukocyte counts to compare stress one hour before, during and after loading via ramp or elevator. Piglets were held in a home pen (control (CON, walked up and down an aisle (handled (HAN, or walked to a truck and loaded via elevator (ELE or ramp (RAM. Sitting, feeding and blood parameters did not show a significant treatment by time effect (p > 0.05. Standing behavior did not differ between CON and HAN piglets nor between RAM and ELE piglets (p > 0.05; however, CON and HAN piglets stood more than RAM and ELE piglets during treatment (p < 0.05. After treatment, drinking behavior was increased in RAM piglets (p < 0.05. The heart rate of ELE piglets decreased 6.3% after treatment; whereas the heart rate of RAM piglets remained elevated 2.4% (p < 0.05. In terms of heart rate, loading by elevator appears to be less stressful than loading by ramp.

Food photographs in portion size estimation among adolescent Mozambican girls.

Science.gov (United States)

Korkalo, Liisa; Erkkola, Maijaliisa; Fidalgo, Lourdes; Nevalainen, Jaakko; Mutanen, Marja

2013-09-01

To assess the validity of food photographs in portion size estimation among adolescent girls in Mozambique. The study was carried out in preparation for the larger ZANE study, which used the 24 h dietary recall method. Life-sized photographs of three portion sizes of two staple foods and three sauces were produced. Participants ate weighed portions of one staple food and one sauce. After the meal, they were asked to estimate the amount of food with the aid of the food photographs. Zambezia Province, Mozambique. Ninety-nine girls aged 13–18 years. The mean differences between estimated and actual portion sizes relative to the actual portion size ranged from 219% to 8% for different foods. The respective mean difference for all foods combined was 25% (95% CI 212, 2 %). Especially larger portions of the staple foods were often underestimated. For the staple foods, between 62% and 64% of the participants were classified into the same thirds of the distribution of estimated and actual food consumption and for sauces, the percentages ranged from 38% to 63%. Bland–Altman plots showed wide limits of agreement. Using life-sized food photographs among adolescent Mozambican girls resulted in a rather large variation in the accuracy of individuals’ estimates. The ability to rank individuals according to their consumption was, however, satisfactory for most foods. There seems to be a need to further develop and test food photographs used in different populations in Sub-Saharan Africa to improve the accuracy of portion size estimates.

Crack width monitoring of concrete structures based on smart film

International Nuclear Information System (INIS)

Zhang, Benniu; Wang, Shuliang; Li, Xingxing; Zhang, Xu; Yang, Guang; Qiu, Minfeng

2014-01-01

Due to its direct link to structural security, crack width is thought to be one of the most important parameters reflecting damage conditions of concrete structures. However, the width problem is difficult to solve with the existing structural health monitoring methods. In this paper, crack width monitoring by means of adhering enameled copper wires with different ultimate strains on the surface of structures is proposed, based on smart film crack monitoring put forward by the present authors. The basic idea of the proposed method is related to a proportional relationship between the crack width and ultimate strain of the broken wire. Namely, when a certain width of crack passes through the wire, some low ultimate strain wires will be broken and higher ultimate strain wires may stay non-broken until the crack extends to a larger scale. Detection of the copper wire condition as broken or non-broken may indicate the width of the structural crack. Thereafter, a multi-layered stress transfer model and specimen experiment are performed to quantify the relationship. A practical smart film is then redesigned with this idea and applied to Chongqing Jiangjin Yangtze River Bridge. (paper)

Crack width monitoring of concrete structures based on smart film

Science.gov (United States)

Zhang, Benniu; Wang, Shuliang; Li, Xingxing; Zhang, Xu; Yang, Guang; Qiu, Minfeng

2014-04-01

Due to its direct link to structural security, crack width is thought to be one of the most important parameters reflecting damage conditions of concrete structures. However, the width problem is difficult to solve with the existing structural health monitoring methods. In this paper, crack width monitoring by means of adhering enameled copper wires with different ultimate strains on the surface of structures is proposed, based on smart film crack monitoring put forward by the present authors. The basic idea of the proposed method is related to a proportional relationship between the crack width and ultimate strain of the broken wire. Namely, when a certain width of crack passes through the wire, some low ultimate strain wires will be broken and higher ultimate strain wires may stay non-broken until the crack extends to a larger scale. Detection of the copper wire condition as broken or non-broken may indicate the width of the structural crack. Thereafter, a multi-layered stress transfer model and specimen experiment are performed to quantify the relationship. A practical smart film is then redesigned with this idea and applied to Chongqing Jiangjin Yangtze River Bridge.

Effects of portion size on chronic energy intake

Directory of Open Access Journals (Sweden)

Pentel Paul R

2007-06-01

Full Text Available Abstract Background This study experimentally examined the effects of repeated exposure to different meal portion sizes on energy intake. Methods Nineteen employees of a county medical center were given free box lunches for two months, one month each of 1528 and 767 average kcal. Foods were identical in the two conditions, but differed in portion size. Meals averaged 44% calories from fat. Participants self-reported how much of each lunch was eaten. Unannounced 24-hour dietary recalls were also conducted by phone twice per week during each exposure period. Results Mean energy intake at the lunch meal was 332 kcal/day higher in large lunch than in small lunch periods (p Conclusion This study suggests that chronic exposure to large portion size meals can result in sustained increases in energy intake and may contribute to body weight increases over time.

GGA+U study of uranium mononitride: A comparison of the U-ramping and occupation matrix schemes and incorporation energies of fission products

Energy Technology Data Exchange (ETDEWEB)

Claisse, Antoine, E-mail: claisse@kth.se [KTH Royal Institute of Technology, Reactor Physics, AlbaNova University Centre, 106 91 Stockholm (Sweden); Klipfel, Marco [European Commission, Joint Research Centre, Institute for Transuranium Elements, P.O. Box 2340, D-76125 Karlsruhe (Germany); Lindbom, Niclas [KTH Royal Institute of Technology, Reactor Physics, AlbaNova University Centre, 106 91 Stockholm (Sweden); Freyss, Michel [CEA, DEN, DEC, Centre de Cadarache, 13108 Saint-Paul-lez-Durance (France); Olsson, Pär [KTH Royal Institute of Technology, Reactor Physics, AlbaNova University Centre, 106 91 Stockholm (Sweden)

2016-09-15

Uranium mononitride is studied in the DFT + U framework. Its ground state is investigated and a study of the incorporation of diverse fission products in the crystal is conducted. The U-ramping and occupation matrix control (OMC) schemes are used to eliminate metastable states. Beyond a certain amount of introduced correlation, the OMC scheme starts to find a lower total energy. The OMC scheme is chosen for the second part of this study. Furthermore, the influence of the magnetic ordering is studied using the U-ramping method, showing that antiferromagnetic order is the most stable one when the U parameter is larger than 1.75 eV. The effect on the density of states is investigated and elastic constants are provided for comparison with other methods and experiments. The incorporation energies of fission products in different defect configurations are calculated and these energies are corrected to take into account the limited size of the supercell. - Highlights: • We studied bulk uranium nitride with means of DFT+U with the U-ramping scheme and the OMC scheme. • We produces a density of states plot and calculated the elastic constants of UN. • We calculated the incorporation energy of many fission products in UN, and corrected them to take into account the elastic interactions. • The OMC scheme should be used over the U-ramping scheme. • Fission products go to larger crystal sites.

Morphodynamics structures induced by variations of the channel width

Science.gov (United States)

Duro, Gonzalo; Crosato, Alessandra; Tassi, Pablo

2014-05-01

In alluvial channels, forcing effects, such as a longitudinally varying width, can induce the formation of steady bars (Olesen, 1984). The type of bars that form, such as alternate, central or multiple, will mainly depend on the local flow width-to-depth ratio and on upstream conditions (Struiksma et al., 1985). The effects on bar formation of varying the channel width received attention only recently and investigations, based on flume experiments and mathematical modelling, are mostly restricted to small longitudinal sinusoidal variations of the channel width (e.g. Repetto et al., 2002; Wu and Yeh, 2005, Zolezzi et al., 2012; Frascati and Lanzoni, 2013). In this work, we analyze the variations in equilibrium bed topography in a longitudinal width-varying channel with characteristic scales of the Waal River (The Netherlands) using two different 2D depth-averaged morphodynamic models, one based on the Delft3D code and one on Telemac-Mascaret system. In particular, we explore the effects of changing the wavelength of sinusoidal width variations in a straight channel, focusing on the effects of the spatial lag between bar formation and forcing that is observed in numerical models and laboratory experiments (e.g. Crosato et al, 2011). We extend the investigations to finite width variations in which longitudinal changes of the width-to-depth ratio are such that they may affect the type of bars that become unstable (alternate, central or multiple bars). Numerical results are qualitatively validated with field observations and the resulting morphodynamic pattern is compared with the physics-based predictor of river bar modes by Crosato and Mosselman (2009). The numerical models are finally used to analyse the experimental conditions of Wu and Yeh (2005). The study should be seen as merely exploratory. The aim is to investigate possible approaches for future research aiming at assessing the effects of artificial river widening and narrowing to control bar formation in

Portion and Serving Sizes of Commonly Consumed Foods, in ...

African Journals Online (AJOL)

Portion sizes were determined from weight equivalents of each food type consumed, average portion sizes for each food type were determined using the statistical ... Serving sizes determined: a serving of the various foods as expressed in household measures include; 1.3 slices of bread, 13.5 tablespoons of Ewedu soup, ...

Portion control for the treatment of obesity in the primary care setting

Directory of Open Access Journals (Sweden)

Harris Katherine I

2011-09-01

Full Text Available Abstract Background The increasing prevalence of obesity is a significant health threat and a major public health challenge. A critical need exists to develop and evaluate practical methods for the treatment of obesity in the clinical setting. One of the factors contributing to the obesity epidemic is food portion sizes. Limited data are available on the efficacy of visual or tactile devices designed to enhance patient understanding and control of portion sizes. A portion control plate is a commercially-available product that can provide visual cues of portion size and potentially contribute to weight loss by enhancing portion size control among obese patients. This tool holds promise as a useful adjunct to dietary counseling. Our objective was to evaluate a portion control intervention including dietary counseling and a portion control plate to facilitate weight loss among obese patients in a primary care practice. Findings We randomized 65 obese patients [body mass index (BMI ≥ 30 and vs. -0.5% ± 2.2%; p = 0.041 and a non significant trend in weight change from baseline at 6 months (-2.1% ± 3.8% vs. -0.7% ± 3.7%; p = 0.232 compared with usual care. Nearly one-half of patients assigned to the portion control intervention who completed the study reported the overall intervention was helpful and the majority would recommend it to others. Conclusions Our findings suggest that a portion control intervention incorporating dietary counseling and a portion control plate may be effective for enhancing weight loss among obese subjects. A portion control intervention deserves further evaluation as a weight control strategy in the primary care setting. Trial registration Current controlled trials NCT01451554

Effective spectrum width of the synchrotron radiation

Energy Technology Data Exchange (ETDEWEB)

Bagrov, V. G., E-mail: bagrov@phys.tsu.ru [Department of Physics, Tomsk State University, Tomsk (Russian Federation); Institute of High Current Electronics, SB RAS, Tomsk (Russian Federation); Gitman, D. M., E-mail: gitman@if.usp.br [Department of Physics, Tomsk State University, Tomsk (Russian Federation); Institute of Physics, University of São Paulo, São Paulo (Brazil); P.N.Lebedev Physical Institute, Moscow (Russian Federation); Levin, A. D., E-mail: alevin@if.usp.br [Institute of Physics, University of São Paulo, São Paulo (Brazil); Loginov, A. S.; Saprykin, A. D. [Department of Physics, Tomsk State University, Tomsk (Russian Federation)

2015-11-25

For an exact quantitative description of spectral properties of synchrotron radiation (SR), the concept of effective width of the spectrum is introduced. In the most interesting case, which corresponds to the ultrarelativistic limit of SR, the effective width of the spectrum is calculated for the polarization components, and new physically important quantitative information on the structure of spectral distributions is obtained. For the first time, the spectral distribution for the circular polarization component of the SR for the upper half-space is obtained within classical theory.

Effective spectrum width of the synchrotron radiation

International Nuclear Information System (INIS)

Bagrov, V. G.; Gitman, D. M.; Levin, A. D.; Loginov, A. S.; Saprykin, A. D.

2015-01-01

For an exact quantitative description of spectral properties of synchrotron radiation (SR), the concept of effective width of the spectrum is introduced. In the most interesting case, which corresponds to the ultrarelativistic limit of SR, the effective width of the spectrum is calculated for the polarization components, and new physically important quantitative information on the structure of spectral distributions is obtained. For the first time, the spectral distribution for the circular polarization component of the SR for the upper half-space is obtained within classical theory

Effective spectrum width of the synchrotron radiation

Energy Technology Data Exchange (ETDEWEB)

Bagrov, V.G. [Tomsk State University, Department of Physics, Tomsk (Russian Federation); SB RAS, Institute of High Current Electronics, Tomsk (Russian Federation); Gitman, D.M. [Tomsk State University, Department of Physics, Tomsk (Russian Federation); University of Sao Paulo, Institute of Physics, Sao Paulo (Brazil); P.N. Lebedev Physical Institute, Moscow (Russian Federation); Levin, A.D. [University of Sao Paulo, Institute of Physics, Sao Paulo (Brazil); Loginov, A.S.; Saprykin, A.D. [Tomsk State University, Department of Physics, Tomsk (Russian Federation)

2015-11-15

For an exact quantitative description of spectral properties of synchrotron radiation (SR), the concept of effective width of the spectrum is introduced. In the most interesting case, which corresponds to the ultrarelativistic limit of SR, the effective width of the spectrum is calculated for the polarization components, and new physically important quantitative information on the structure of spectral distributions is obtained. For the first time, the spectral distribution for the circular polarization component of the SR for the upper half-space is obtained within classical theory. (orig.)

Energy intake and obesity: ingestive frequency outweighs portion size.

Science.gov (United States)

Mattes, Richard

2014-07-01

Energy intake is a function of the quantity of energy consumed per ingestive event and the number of these events. The marked increase of energy intake and body weight over the past 35 years indicates that there has been poor precision in the reciprocity of these two facets of intake. With recent study of the associations between gut "satiation" peptides and energy intake, there has been an emphasis on the contribution of portion size to positive energy balance. However, this orientation may not appropriately weight the contribution of ingestive frequency. Gut peptides are not purely satiation factors and metabolic and environmental cues may more strongly guide the onset and number of ingestive events. Evidence is presented that while both portion size and ingestive frequency have increased in the population, the latter may be more problematic for weight gain. The magnitude and time course of increments in ingestive frequency map better onto energy intake and BMI trends than changes of portion size. This may occur, in part, because dietary compensation and thermogenic effects are weaker for increases in ingestive frequency than portion size. Though not to the exclusion of consideration of portion size effects, improved weight management may be achieved with greater attention to the drivers of eating and drinking frequency. Copyright © 2013 Elsevier Inc. All rights reserved.

Effect of adaptive cruise control systems on mixed traffic flow near an on-ramp

Science.gov (United States)

Davis, L. C.

2007-06-01

Mixed traffic flow consisting of vehicles equipped with adaptive cruise control (ACC) and manually driven vehicles is analyzed using car-following simulations. Simulations of merging from an on-ramp onto a freeway reported in the literature have not thus far demonstrated a substantial positive impact of ACC. In this paper cooperative merging for ACC vehicles is proposed to improve throughput and increase distance traveled in a fixed time. In such a system an ACC vehicle senses not only the preceding vehicle in the same lane but also the vehicle immediately in front in the other lane. Prior to reaching the merge region, the ACC vehicle adjusts its velocity to ensure that a safe gap for merging is obtained. If on-ramp demand is moderate, cooperative merging produces significant improvement in throughput (20%) and increases up to 3.6 km in distance traveled in 600 s for 50% ACC mixed flow relative to the flow of all-manual vehicles. For large demand, it is shown that autonomous merging with cooperation in the flow of all ACC vehicles leads to throughput limited only by the downstream capacity, which is determined by speed limit and headway time.

Loading and Unloading Weaned Pigs: Effects of Bedding Types, Ramp Angle, and Bedding Moisture

Directory of Open Access Journals (Sweden)

Arlene Garcia

2014-12-01

Full Text Available The use of non-slip surfaces during loading and unloading of weaned pigs plays an important role in animal welfare and economics of the pork industry. Currently, the guidelines available only suggest the use of ramps below 20° to load and unload pigs. Three ramp angles (0°, 10° or 20°, five bedding materials (nothing, sand, feed, wood shavings or wheat straw hay, two moistures (dry or wet bedding; >50% moisture over two seasons (>23.9 °C summer, <23.9 °C winter were assessed for slips/falls/vocalizations (n = 6,000 pig observations. “Score” was calculated by the sum of slips, falls, and vocalizations. With the exception of using feed as a bedding, all beddings provided some protection against elevated slips, falls, and vocalizations (P < 0.01. Providing bedding reduced (P < 0.05 scores regardless of whether the bedding was dry or wet. Scores increased as the slope increased (P < 0.01. Provision of bedding, other than feed, at slopes greater than zero, decreased slips, falls and vocalizations. The total time it took to load and unload pigs was

Suppression of high-frequency perturbations in pulse-width modulation

DEFF Research Database (Denmark)

2008-01-01

A method suppresses high-frequency perturbations in a pulse-width modulated signal. The pulse-width modulation may superpose a carrier signal onto an input signal having a predetermined modulation frequency. The carrier signals may be phase-shifted. The resulting modulated signals may...

Climatological attribution of wind power ramp events in East Japan and their probabilistic forecast based on multi-model ensembles downscaled by analog ensemble using self-organizing maps

Science.gov (United States)

Ohba, Masamichi; Nohara, Daisuke; Kadokura, Shinji

2016-04-01

Severe storms or other extreme weather events can interrupt the spin of wind turbines in large scale that cause unexpected "wind ramp events". In this study, we present an application of self-organizing maps (SOMs) for climatological attribution of the wind ramp events and their probabilistic prediction. The SOM is an automatic data-mining clustering technique, which allows us to summarize a high-dimensional data space in terms of a set of reference vectors. The SOM is applied to analyze and connect the relationship between atmospheric patterns over Japan and wind power generation. SOM is employed on sea level pressure derived from the JRA55 reanalysis over the target area (Tohoku region in Japan), whereby a two-dimensional lattice of weather patterns (WPs) classified during the 1977-2013 period is obtained. To compare with the atmospheric data, the long-term wind power generation is reconstructed by using a high-resolution surface observation network AMeDAS (Automated Meteorological Data Acquisition System) in Japan. Our analysis extracts seven typical WPs, which are linked to frequent occurrences of wind ramp events. Probabilistic forecasts to wind power generation and ramps are conducted by using the obtained SOM. The probability are derived from the multiple SOM lattices based on the matching of output from TIGGE multi-model global forecast to the WPs on the lattices. Since this method effectively takes care of the empirical uncertainties from the historical data, wind power generation and ramp is probabilistically forecasted from the forecasts of global models. The predictability skill of the forecasts for the wind power generation and ramp events show the relatively good skill score under the downscaling technique. It is expected that the results of this study provides better guidance to the user community and contribute to future development of system operation model for the transmission grid operator.

Correlation of H-mode density barrier width and neutral penetration length

International Nuclear Information System (INIS)

Groebner, R.J.

2002-01-01

Pedestal studies in DIII-D find a good correlation between the width of the H-mode particle barrier width(ne) and the neutral penetration length. These results are obtained by comparing experimental n e profiles to the predictions of an analytic model for the density profile, obtained from a solution of the particle continuity equations for electrons and deuterium atoms. Initial bench-marking shows that the model is consistent with the fluid neutrals model of the UEDGE code. In its range of validity (edge temperature between 0.02-0.3 keV), the model quantitatively predicts the observed values of width(ne), the observed decrease of width(ne) as the pedestal density n e,ped increases, the observed increase of the gradient of n e with the square of n e,ped , and the observation that L-mode and H-mode profiles with the same n e,ped have very similar widths. In the model, width(ne) depends on the fuelling source and on the plasma transport. Thus, these results provide evidence that the width of the particle barrier depends on both plasma physics and atomic physics. (author)

How food marketers can sell smaller portions: Consumer insights and product innovation.

Science.gov (United States)

Riis, J; Fisher, J O; Rowe, S

2016-08-01

Food portion size has been shown to be an important driver of energy intake. Despite the well acknowledged role of portion control in weight management, large portion sizes remain ubiquitous in the marketplace. Moving consumers towards consumption of smaller portion sizes will require changes in consumer behavior as well as changes in products available to consumers in a variety of settings. This special supplement presents cutting edge research aimed at understanding consumer behavior around portion size and innovations in product design that may promote the selection and consumption of smaller portion sizes. We identify further research that will be needed to translate basic behavioral findings into real world settings and to viable product development. Copyright © 2016. Published by Elsevier Ltd.

Losses analysis of soft magnetic ring core under sinusoidal pulse width modulation (SPWM) and space vector pulse width modulation (SVPWM) excitations

Science.gov (United States)

Gao, Hezhe; Li, Yongjian; Wang, Shanming; Zhu, Jianguo; Yang, Qingxin; Zhang, Changgeng; Li, Jingsong

2018-05-01

Practical core losses in electrical machines differ significantly from those experimental results using the standardized measurement method, i.e. Epstein Frame method. In order to obtain a better approximation of the losses in an electrical machine, a simulation method considering sinusoidal pulse width modulation (SPWM) and space vector pulse width modulation (SVPWM) waveforms is proposed. The influence of the pulse width modulation (PWM) parameters on the harmonic components in SPWM and SVPWM is discussed by fast Fourier transform (FFT). Three-level SPWM and SVPWM are analyzed and compared both by simulation and experiment. The core losses of several ring samples magnetized by SPWM, SVPWM and sinusoidal alternating current (AC) are obtained. In addition, the temperature rise of the samples under SPWM, sinusoidal excitation are analyzed and compared.

Influence of electrical sheet width on dynamic magnetic properties

CERN Document Server

Chevalier, T; Cornut, B

2000-01-01

Effects of the width of electrical steel sheets on dynamic magnetic properties are investigated by solving diffusion equation on the cross-section of the sheet. Linear and non-linear cases are studied, and are compared with measurement on Epstein frame. For the first one an analytical solution is found, while for the second, a 2D finite element simulation is achieved. The influence of width is highlighted for a width thickness ratio lower than 10. It is shown that the behaviour modification in such cases is conditioned by the excitation signal waveform, amplitude and also frequency.

Analysis of the potential of building ramps in hydrotechnical structures as a means of facilitating fish migration

Directory of Open Access Journals (Sweden)

Tomasz Tymiński

2016-09-01

Full Text Available Measures aimed at preserving “ecological corridors” in rivers are a difficult and complex issue that requires specialized knowledge from many science disciplines. Fishways are one of the most important solutions that ensure the ecological continuity of rivers for fish, particularly due to their near-natural design. A characteristic feature of their construction is the use of natural building materials (stones, tree stumps, gravel, and vegetation in such a way that their appearance resembles asmall watercourse. The design of hydraulic fishways is based only on the criterion of maximum speed (vmax and the parameter of unitary energy of water E; it does not provide complete information about these devices’ efficiency. In order to produce optimal flow conditions for ichthyofauna in the fishway, there is a need for research into the spatial distribution of the hydraulic parameters, such as disorders of the flow velocity field or distributions of turbulence (Tu. The aim and scope of this work was to examine the potential of building fish ramps as a means of creating a watercourse through hydrotechnical structures, in order to facilitate fish migration. For this purpose, research was conducted on a physical model in the water laboratory of Prof. Julian Wołoszyn at the Wrocław University of Environmental and Life Sciences. A physical model of a fish ramp was built. Depths and flow speeds at the established water flow rate were measured. Depths of water in the fishway were evaluated in strategic places for fish – i.e. at the entrance and exit of the fishway and between cylindric stones (flow obstacles on the ramp. The speed was measured at mesh nodes which are spaced at intervals of 15 cm along the length of the riverbed and of 10 cm across the cross section. Maps of the spatial distribution of the flow velocity were drafted based on the results obtained, from which maximum and minimum speeds, stream/current distribution and a rest zone for

Heat generation and cooling of SSC magnets at high ramp rates

International Nuclear Information System (INIS)

Snitchler, G.; Capone, D.; Kovachev, V.; Schermer, R.

1992-01-01

This presentation will address a summary of AC loss calculations (SSCL), experimental results on cable samples (Westinghouse STC), short model magnets test results (FNAL, KEK-Japan), and recent full length magnets test data on AC losses and quench current ramp rate sensitivity (FNAL, BNL). Possible sources of the observed enhanced heat generation and quench sensitivity for some magnets will be discussed. A model for cooling conditions of magnet coils considering heat generation distribution and specific anisotropy of the heat transfer will be presented. The crossover contact resistance in cables and curing procedure influence on resistivity, currently under study, will be briefly discussed. (author)

Ramping Performance Analysis of the Kahuku Wind-Energy Battery Storage System

Energy Technology Data Exchange (ETDEWEB)

Gevorgian, V. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Corbus, D. [National Renewable Energy Lab. (NREL), Golden, CO (United States)

2013-11-01

High penetrations of wind power on the electrical grid can introduce technical challenges caused by resource variability. Such variability can have undesirable effects on the frequency, voltage, and transient stability of the grid. Energy storage devices can be an effective tool in reducing variability impacts on the power grid in the form of power smoothing and ramp control. Integrating anenergy storage system with a wind power plant can help smooth the variable power produced from wind. This paper explores the fast-response, megawatt-scale, wind-energy battery storage systems that were recently deployed throughout the Hawaiian islands to support wind and solar projects.

Fast and Robust Nanocellulose Width Estimation Using Turbidimetry.

Science.gov (United States)

Shimizu, Michiko; Saito, Tsuguyuki; Nishiyama, Yoshiharu; Iwamoto, Shinichiro; Yano, Hiroyuki; Isogai, Akira; Endo, Takashi

2016-10-01

The dimensions of nanocelluloses are important factors in controlling their material properties. The present study reports a fast and robust method for estimating the widths of individual nanocellulose particles based on the turbidities of their water dispersions. Seven types of nanocellulose, including short and rigid cellulose nanocrystals and long and flexible cellulose nanofibers, are prepared via different processes. Their widths are calculated from the respective turbidity plots of their water dispersions, based on the theory of light scattering by thin and long particles. The turbidity-derived widths of the seven nanocelluloses range from 2 to 10 nm, and show good correlations with the thicknesses of nanocellulose particles spread on flat mica surfaces determined using atomic force microscopy. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

SOUTH RAMP DEVIATED ALIGNMENT 3.01.X AREA GROUND SUPPORT ANALYSIS (STATION 71+07.10 TO 71+44.10)

International Nuclear Information System (INIS)

M.J. Mrugala

2000-01-01

The purpose of the analysis is to provide a basis for ensuring safe conditions in the Case VI area. The scope of this analysis is to analyze and recommend future action for a section of the South Ramp with a deviated alignment, here referred to as Case VI 3.01.X area. This area is located between Stations 71+07.10 to 71+44.10 in the South Ramp of the ESF (Exploratory Studies Facility) Main Loop tunnel. The scope of the analysis includes accomplishing the following goals: (1) Document the as-built configuration including existing voids and installed ground support; (2) Document the geotechnical properties of the rock mass and structural features; and (3) Evaluate the stability and develop recommendations for future action

A clinical and histologic evaluation of gingival fibroblasts seeding on a chitosan-based scaffold and its effect on the width of keratinized gingiva in dogs.

Science.gov (United States)

Lotfi, Ghogha; Shokrgozar, Mohammad Ali; Mofid, Rasoul; Abbas, Fatemeh Mashhadi; Ghanavati, Farzin; Bagheban, Alireza Akbarzadeh; Shariati, Ramin Pajoum

2011-09-01

Finding biocompatible matrix materials capable of enhancing the procedures of gingival augmentation is a major concern in periodontal research. This has prompted the investigation of a safe grafting technique by means of synthetic or natural polymers. The objective of this study is to examine the effect of a gingival fibroblast cultured on a naturally derived (i.e., chitosan-based) scaffold on the width of keratinized gingiva in dogs. Gingival fibroblasts were cultured from a small portion of hard palates of five dogs. A bilayered chitosan scaffold was seeded with the gingival fibroblasts and transferred to dogs. Surgery was performed bilaterally, and the regions were randomly divided into two groups: chitosan only (control site) and chitosan + fibroblast (test site). Periodontal parameters, including probing depth and width of keratinized and attached gingiva, were measured at baseline and 3 months after surgery. A histologic evaluation was also performed on the healed grafted sites. Comparison of width of keratinized and attached gingiva in control and test sites showed that the mean width of keratinized and attached gingiva increased in each group after surgery. However, the difference between control and test groups was not statistically significant. Concerning the existence of the keratinized epithelium, exocytosis, and epithelium thickness, no significant difference was observed in test and control sites. The difference was significant in relation to rete ridge formation. The tissue-engineered graft consisting of chitosan + fibroblast was applied to gingival augmentation procedures and generated keratinized tissue without any complications usually associated with donor-site surgery.

Ramp compression of a metallic liner driven by a shaped 5 MA current on the SPHINX machine

Science.gov (United States)

d'Almeida, T.; Lassalle, F.; Morell, A.; Grunenwald, J.; Zucchini, F.; Loyen, A.; Maysonnave, T.; Chuvatin, A.

2014-05-01

SPHINX is a 6MA, 1-us Linear Transformer Driver operated by the CEA Gramat (France) and primarily used for imploding Z-pinch loads for radiation effects studies. A method for performing magnetic ramp compression experiments was developed using a compact Dynamic Load Current Multiplier inserted between the convolute and the load, to shape the initial current pulse. We present the overall experimental configuration chosen for these experiments and initial results obtained over a set of experiments on an aluminum cylindrical liner. Current profiles measured at various critical locations across the system, are in good agreement with simulated current profiles. The liner inner free surface velocity measurements agree with the hydrocode results obtained using the measured load current as the input. The potential of the technique in terms of applications and achievable ramp pressure levels lies in the prospects for improving the DLCM efficiency.

Ramp compression of a metallic liner driven by a shaped 5 MA current on the SPHINX machine

International Nuclear Information System (INIS)

D'Almeida, T; Lassalle, F; Morell, A; Grunenwald, J; Zucchini, F; Loyen, A; Maysonnave, T; Chuvatin, A

2014-01-01

SPHINX is a 6MA, 1-us Linear Transformer Driver operated by the CEA Gramat (France) and primarily used for imploding Z-pinch loads for radiation effects studies. A method for performing magnetic ramp compression experiments was developed using a compact Dynamic Load Current Multiplier inserted between the convolute and the load, to shape the initial current pulse. We present the overall experimental configuration chosen for these experiments and initial results obtained over a set of experiments on an aluminum cylindrical liner. Current profiles measured at various critical locations across the system, are in good agreement with simulated current profiles. The liner inner free surface velocity measurements agree with the hydrocode results obtained using the measured load current as the input. The potential of the technique in terms of applications and achievable ramp pressure levels lies in the prospects for improving the DLCM efficiency.

Analysis of the EDIPO Temperature Margin During Current Ramp-Up

CERN Document Server

Marinucci, C; Calvi, Marco; Marinucci, Claudio; Cau, Francesca; Bottura, Luca

2010-01-01

The European dipole (EDIPO), currently under construction, will provide background magnetic fields of up to 12.5 T for tests of ITER high-current superconducting cables. The EDIPO winding consists of 7 x 2 double layers of Nb$_{3}$SN cable-in-conduit conductors with forced flow cooling of supercritical helium. The performance limits of EDIPO during current ramp-up are analyzed analysed with the CryoSoft suite of codes, recently integrated into a customizable and flexible environment for the analysis of thermal hydraulic and electrical transients in superconducting magnetic systems. The simultaneous analysis of the cryogenic system and all 14 double layers shows that under all charging conditions the EDIPO temperature margin remains sufficiently high.

Correlations for reduced-width amplitudes in 49V

International Nuclear Information System (INIS)

Chou, B.H.; Mitchell, G.E.; Bilpuch, E.G.; Westerfeldt, C.R.

1980-01-01

Measurement of the relative sign of inelastic proton-channel amplitudes permits the determination of amplitude correlations. Data were obtained for 45 5/2 + resonances in 49 V. Although the reduced widths in each channel followed a Porter-Thomas distribution, large amplitude correlations were observed. The results are compared with the reduced-width--amplitude distribution of Krieger and Porter. This is the first direct test of the Krieger-Porter distribution

Modified model of neutron resonances widths distributions. Results of reduced neutron widths approximation for mass region 35 ≤ A ≤ 249

International Nuclear Information System (INIS)

Sukhovoj, A.M.; Khitrov, V.A.

2011-01-01

The distributions of the reduced neutron widths of s-, p- and d-resonances of nuclei of any type from nuclear mass region 35 ≤ A ≤ 249 were approximated with maximal precision by the model which presents experimental data set as a superposition of a maximum of four independent neutron amplitudes. Under the assumption that each of these amplitudes has the Gauss distribution with the unique maximum there were determined the most probable values of contribution of each amplitude in summary width distribution, their most probable mean values and dispersions. Comparison of the obtained χ 2 values with value χ 2 at description of the experimental data by one distribution of neutron amplitudes with best fitted parameters shows that all widths from more than 157 analyzed data sets can have different types of wave functions

Correlations between topography and intraflow width behavior in Martian and terrestrial lava flows

Science.gov (United States)

Peitersen, Matthew N.; Crown, David A.

2000-02-01

Local correlations between topography and width behavior within lava flows at Puu Oo, Mount Etna, Glass Mountain, Cerro Bayo, Alba Patera, Tyrrhena Patera, Elysium Mons, and Olympus Mons were investigated. For each flow, width and slope data were both referenced via downflow distance as a sequence of points; the data were then divided into collections of adjacent three-point features and two-point segments. Four discrete types of analyses were conducted: (1) Three-point analysis examined positional correlations between width and slope features, (2) two-point analysis did the same for flow segments, (3) mean slope analysis included segment slope comparisons, and (4) sudden width behavior analysis measured abruptness of width changes. The distribution of types of correlations compared to random combinations of features and segments does not suggest a significant correlation between flow widths and local underlying slopes and indicates that for these flows at least, other factors have more influence on changes in width than changes in underlying topography. Mean slopes underlying narrowing, widening, and constant flow width segments were calculated. An inverse correlation between slope and width was found only at Mount Etna, where slopes underlying narrowing segments were greater than those underlying widening in 62% of the examined flows. For the majority of flows at Mount Etna, Puu Oo, and Olympus Mons, slopes were actually greatest under constant width segments; this may imply a topographically dependent resistance to width changes. The rate of change of width was also examined. Sudden width changes are relatively common at Puu Oo, Mount Etna, Elysium Mons, and Tyrrhena Patera and relatively rare at Glass Mountain, Cerro Bayo, Olympus Mons, and Alba Patera. After correction for mapping scale, Puu Oo, Mount Etna, Olympus Mons, and Alba Patera appear to fall on the same trend; Glass Mount exhibits unusually small amounts of sudden width behavior, and Tyrrhena Patera

The CEA-FRAGEMA ramp test programme for the study of the effect of power cycling on PCI at high burn-up

International Nuclear Information System (INIS)

Joseph, J.; Atabek, R.; Trotabas, M.

1983-01-01

The ramp test programme developed jointly by FRAGEMA and CEA is presented. Today, more than thirty PWR fuel rods have been ramp-tested in experimental reactors SILOE and OSIRIS. Nineteen fuel rods, named 'PRISCA', were base irradiated in BR3 and twelve fuel rods have been refabricated in hot cell by the FABRICE technique. The average fuel burn-up lies between 11 GWd.tU -1 and 46 GWd.tU -1 . In the major cases, the flux profile, during ramp-test, was decentred with respect to the base irradiated flux, and allows to obtain much more information than with a centred flux profile. The failure threshold was established under a set of more than thirty fuel rods of various designs. In particular, the post irradiation examinations allow to locate all rupture locations and thus to define precisely the threshold condition for failure of fuel rods. As an example, the results obtained in the PRISCA 109 experiments are presented. The refabricated fuel rods FABRICE behave identically, with regard to PCI, rather than PRISCA rods. An example of load follow transient in a PWR reactor is presented, and indicates any risk of failure due to PCI. (author)

MMS observations of the Earth bow shock during magnetosphere compression and expansion: comparison of whistler wave properties around the shock ramp

Science.gov (United States)

Russell, C. T.; Strangeway, R. J.; Schwartz, S. J.

2017-12-01

The Magnetospheric Multiscale (MMS) spacecraft, with their state-of-the-art plasma and field instruments onboard, allow us to investigate electromagnetic waves at the bow shock and their association with small-scale disturbances in the shocked plasmas. Understanding these waves could improve our knowledge on the heating of electrons and ions across the shock ramp and the energy dissipation of supercritical shocks. We have found broad-band and narrow band waves across the shock ramp and slightly downstream. The broad-band waves propagate obliquely to the magnetic field direction and have frequencies up to the electron cyclotron frequency, while the narrow-band waves have frequencies of a few hundred Hertz, durations under a second, and are right-handed circularly polarized and propagate along the magnetic field lines. Both wave types are likely to be whistler mode with different generation mechanisms. When the solar wind pressure changes, MMS occasionally observed a pair of bow shocks when the magnetosphere was compressed and then expanded. We compare the wave observations under these two situations to understand their roles in the shock ramp as well as the upstream and downstream plasmas.

CORRELATION OF H-MODE BARRIER WIDTH AND NEUTRAL PENETRATION LENGTH

International Nuclear Information System (INIS)

GROEBNER, R.J.; MAHDAVI, M.A.; LEONARD, A.W.; OSBORNE, T.H.; WOLF, N.S.; PORTER, G.D.; STANGEBY, P.C.; BROOKS, N.H.; COLCHIN, R.J.; HEIDBRINK, W.W.; LUCE, T.C.; MCKEE, G.R.; OWEN, L.W.; WANG, G.; WHYTE, D.G.

2002-01-01

OAK A271 CORRELATION OF H-MODE BARRIER WIDTH AND NEUTRAL PENETRATION LENGTH. Pedestal studies in DIII-D find a good correlation between the width of the H-mode density barrier and the neutral penetration length. These results are obtained by comparing experimental density profiles to the predictions of an analytic model for the profile, obtained from the particle continuity equations for electrons and deuterium atoms. In its range of validity (edge temperature between 40-500 eV), the analytic model quantitatively predicts the observed decrease of the width as the pedestal density increases, the observed strong increase of the gradient of the density as the pedestal density increases and the observation that L-mode and H-mode profiles with the same pedestal density have very similar shapes. The width of the density barrier, measured from the edge of the electron temperature barrier, is the lower limit for the observed width of the temperature barrier. These results support the hypothesis that particle fueling provides the dominant control for the size of the H-mode transport barrier

CORRELATION OF H-MODE BARRIER WIDTH AND NEUTRAL PENTRATION LENGTH

International Nuclear Information System (INIS)

GROEBNER, R.J.; MAHDAVI, M.A.; LEONARD, A.W.; OSBORNE, T.H.; WOLF, N.S.; PORTER, G.D.; STANGEBY, P.C.; BROOKS, N.H.; COLCHIN, R.J.; HEIDBRINK, W.W.; LUCE, T.C.; MCKEE, G.R.; OWEN, L.W.; WANG, G.; WHYTE, D.G.

2002-01-01

OAK A271 CORRELATION OF H-MODE BARRIER WIDTH AND NEUTRAL PENTRATION LENGTH. Pedestal studies in DIII-D find a good correlation between the width of the region of steep gradient in the H-mode density and the neutral penetration length. These results are obtained by comparing experimental density profiles to the predictions of an analytic model for the profile, obtained from the particle continuity equations for electrons and deuterium atoms. In its range of validity (edge temperature between 40-500 eV), the analytic model quantitatively predicts the observed decrease of the width as the pedestal density increases, the observed strong increase of the gradient of the density as the pedestal density increases and the observation that L-mode and H-mode profiles with the same pedestal density have very similar shapes. The width of the density barrier, measured from the edge of the electron temperature barrier, is the lower limit for the observed width of the temperature barrier. These results support the hypothesis that particle fueling provides a dominant control for the size of the H-mode transport barrier

Improving accuracy of portion-size estimations through a stimulus equivalence paradigm.

Science.gov (United States)

Hausman, Nicole L; Borrero, John C; Fisher, Alyssa; Kahng, SungWoo

2014-01-01

The prevalence of obesity continues to increase in the United States (Gordon-Larsen, The, & Adair, 2010). Obesity can be attributed, in part, to overconsumption of energy-dense foods. Given that overeating plays a role in the development of obesity, interventions that teach individuals to identify and consume appropriate portion sizes are warranted. Specifically, interventions that teach individuals to estimate portion sizes correctly without the use of aids may be critical to the success of nutrition education programs. The current study evaluated the use of a stimulus equivalence paradigm to teach 9 undergraduate students to estimate portion size accurately. Results suggested that the stimulus equivalence paradigm was effective in teaching participants to make accurate portion size estimations without aids, and improved accuracy was observed in maintenance sessions that were conducted 1 week after training. Furthermore, 5 of 7 participants estimated the target portion size of novel foods during extension sessions. These data extend existing research on teaching accurate portion-size estimations and may be applicable to populations who seek treatment (e.g., overweight or obese children and adults) to teach healthier eating habits. © Society for the Experimental Analysis of Behavior.

First Metatarsal Head and Medial Eminence Widths with and Without Hallux Valgus.

Science.gov (United States)

Lenz, Robin C; Nagesh, Darshan; Park, Hannah K; Grady, John

2016-09-02

Resection of the medial eminence in hallux valgus surgery is common. True hypertrophy of the medial eminence in hallux valgus is debated. No studies have compared metatarsal head width in patients with hallux valgus and control patients. We reviewed 43 radiographs with hallux valgus and 27 without hallux valgus. We measured medial eminence width, first metatarsal head width, and first metatarsal shaft width in patients with and without radiographic hallux valgus. Medial eminence width was 1.12 mm larger in patients with hallux valgus (P hallux valgus (P hallux valgus. However, frontal plane rotation of the first metatarsal likely accounts for this difference.

Effects of two-temperature parameter and thermal nonlocal parameter on transient responses of a half-space subjected to ramp-type heating

Science.gov (United States)

Xue, Zhang-Na; Yu, Ya-Jun; Tian, Xiao-Geng

2017-07-01

Based upon the coupled thermoelasticity and Green and Lindsay theory, the new governing equations of two-temperature thermoelastic theory with thermal nonlocal parameter is formulated. To more realistically model thermal loading of a half-space surface, a linear temperature ramping function is adopted. Laplace transform techniques are used to get the general analytical solutions in Laplace domain, and the inverse Laplace transforms based on Fourier expansion techniques are numerically implemented to obtain the numerical solutions in time domain. Specific attention is paid to study the effect of thermal nonlocal parameter, ramping time, and two-temperature parameter on the distributions of temperature, displacement and stress distribution.

Modelling the widths of fission observables in GEF

Directory of Open Access Journals (Sweden)

Schmidt K.-H.

2013-03-01

Full Text Available The widths of the mass distributions of the different fission channels are traced back to the probability distributions of the corresponding quantum oscillators that are coupled to the heat bath, which is formed by the intrinsic degrees of freedom of the fissioning system under the influence of pairing correlations and shell effects. Following conclusion from stochastic calculations of Adeev and Pashkevich, an early freezing due to dynamical effects is assumed. It is shown that the mass width of the fission channels in low-energy fission is strongly influenced by the zero-point motion of the corresponding quantum oscillator. The observed variation of the mass widths of the asymmetric fission channels with excitation energy is attributed to the energy-dependent properties of the heat bath and not to the population of excited states of the corresponding quantum oscillator.

Metallographic examination of (uth) O2 and UO2 fuel tested in power ramp conditions in triga reactor

International Nuclear Information System (INIS)

Ioncescu, M.; Uta, O.

2015-01-01

The purpose of this paper is to determine the behavior of two fuel experimental elements (EC1 and EC2), by destructive post-irradiation examination. The fuel elements were mounted inside a pattern port, one in extension of the other and irradiated in power ramp conditions in order to check their behavior. Fuel element 1 (EC1) contains (UTh)O''2 pellet, and other one (EC2) UO''2 pellet. The results of destructive post-irradiation examination are evidenced by metallographic and ceramographic analyses. The data obtained from the post-irradiation examinations are used, first to confirm the security, reliability and nuclear fuel performance, and second, for the development of CANDU fuel. The results obtained by destructive examinations regarding the integrity, sheath hydrating and oxidation as well as the structural modifications are typical for fuel elements tested in power ramp conditions. (authors)

AN OPTIMAL REPLENISHMENT POLICY FOR DETERIORATING ITEMS WITH RAMP TYPE DEMAND UNDER PERMISSIBLE DELAY IN PAYMENTS

Directory of Open Access Journals (Sweden)

Dr. Sanjay Jain

2010-10-01

Full Text Available The aim of this paper is to develop an optimal replenishment policy for inventory models of deteriorating items with ramp type demand under permissible delay in payments. Deterioration of items begins on their arrival in stock.  An example is also presented to illustrate the application of developed model.

Line width of Josephson flux flow oscillators

DEFF Research Database (Denmark)

Koshelets, V.P.; Dmitriev, P.N.; Sobolev, A.S.

2002-01-01

to be proven before one initiates real FFO applications. To achieve this goal a comprehensive set of line width measurements of the FFO operating in different regimes has been performed. FFOs with tapered shape have been successfully implemented in order to avoid the superfine resonant structure with voltage...... spacing of about 20 nV and extremely low differential resistance, recently observed in the IVC of the standard rectangular geometry. The obtained results have been compared with existing theories and FFO models in order to understand and possibly eliminate excess noise in the FFO. The intrinsic line width...

Pulse-width discriminators

International Nuclear Information System (INIS)

Budyashov, Yu.G.; Grebenyuk, V.M.; Zinov, V.G.

1978-01-01

A pulse duration discriminator is described which is intended for processing signals from multilayer scintillators. The basic elements of the scintillator are: an input gate, a current generator, an integrating capacitor, a Schmidt trigger and an anticoincidence circuit. The basic circuit of the discriminator and its time diagrams explaining its operating are given. The discriminator is based on microcircuits. Pulse duration discrimination threshold changes continuously from 20 to 100 ns, while its amplitude threshold changes within 20 to 100 mV. The temperature instability of discrimination thresholds (both in pulse width and in amplitude) is better than 0.1 per cent/deg C

Constant Width Planar Computation Characterizes ACC⁰

DEFF Research Database (Denmark)

Hansen, K.A.

2004-01-01

We obtain a characterization of ACC 0 in terms of a natural class of constant width circuits, namely in terms of constant width polynomial size planar circuits. This is shown via a characterization of the class of acyclic digraphs which can be embedded on a cylinder surface in such a way that all...

Analysis Of The Effect Of Flow Channel Width On The Performance Of PEMFC

Directory of Open Access Journals (Sweden)

Elif Eker

2013-08-01

Full Text Available In this work, it was analysed the effect of different channel width on performance of PEM fuel cell. Current density were measured on the single cells of parallel flow fields that has 25 cm² active layer, using three different kinds of channel width. The cell width and the channel height remain constant.The results show that increasing the channel width while the cell width remains constant decreases the current density.

Requirements to gap widths and clamping for CO2 laser butt welding

DEFF Research Database (Denmark)

Gong, Hui; Juhl, Thomas Winther

1999-01-01

In the experimental study of fixturing and gap width requirements a clamping device for laser butt welding of steel sheets has been developed and tested. It has fulfilled the work and made the gap width experiments possible.It has shown that the maximum allowable gap width to some extent...... is inversely related to the welding speed. Also larger laser power leads to bigger allowable gap widths. The focal point position, though, has little influence on the maximum allowable gap width.During analysis X-ray photos show no interior porosity in the weld seam. Other methods have been applied to measure...... responses from variations in welding parameters.The table below lists the results of the study, showing the maximum allowable gap widths and some corresponding welding parameters.Maximum allowable Gap Width; Welding Speed; Laser Power:0.10 mm2 m/min2, 2.6 kW0.15 mm1 m/min2 kW0.20 mm1 m/min2.6 kW0.30 mm0.5 m...

Analysis of the width correlation in 54Fe(nγ)55Fe reaction

International Nuclear Information System (INIS)

Knat'ko, V.A.; Shimanovich, E.A.

1982-01-01

To find out structural effects manifesting themselves in the form of correlation between widths of different channels of γ decay of levels and violation of Porter-Thomas distribution, calculated are partial widths of levels for 20 high-energy γ transitions in the 54 Fe(nγ) 55 Fe reaction. Calculations are carried out for widths in relation to γ transitions on 8 low p levels of 55 Fe, for 100 sets of partial γ widths (20 widths in a set). Results of analysis of theoretical values of partial γ widths of s resonances are presented in the form of the table. Results, obtained, show that consideration of contributions into γ decay of one-particle-vibrational configurations improve the accordance with experimental data, in comparison with calculations according to the model of valent capture. It is concluded that properties of γ widths of 55 Fe resonances, calculated in studied model, agree satisfactorily with properties of experimental γ widths [ru

40 CFR 1045.505 - How do I test engines using discrete-mode or ramped-modal duty cycles?

Science.gov (United States)

2010-07-01

...-mode or ramped-modal duty cycles? 1045.505 Section 1045.505 Protection of Environment ENVIRONMENTAL...-modal duty cycles? (a) This section describes how to test engines under steady-state conditions. We... Act. Conduct duty-cycle testing as follows: (1) For discrete-mode testing, sample emissions separately...

Sedimentology and preservation of aeolian sediments on steep terrains : Incipient sand ramps on the Atacama coast (northern Chile)

NARCIS (Netherlands)

Ventra, Dario; Rodríguez-López, Juan Pedro; de Boer, Poppe L.

2017-01-01

The origin of topographically controlled aeolian landforms in high-relief settings is difficult to synthesize under general models, given the dependence of such accumulations on local morphology. Quaternary sand ramps have been linked to palaeoclimate, regional geomorphology and wind patterns;

Obstructing Gangliocytic Paraganglioma in the Third Portion of the Duodenum

Directory of Open Access Journals (Sweden)

Carlos M. Nuño-Guzmán

2012-07-01

Full Text Available Gangliocytic paragangliomas are infrequent tumors almost exclusively found in the second portion of the duodenum. An unusual case of a gangliocytic paraganglioma in the third portion of the duodenum with obstructive symptoms is herein reported. A 16-year-old male patient presented with epigastric pain, postprandial plenitude and reflux. A barium swallow failed to demonstrate abnormalities. Endoscopy showed a pedunculated submucosal tumor, originating at the third duodenal portion and causing partial obstruction. Biopsy was not performed due to the risk of bleeding. CT scan demonstrated a polypoid lesion. Through a transmesocolic approach and an anterior duodenotomy, resection of the tumor was performed. No lymph node or other organ affection was found. Histologic examination revealed a gangliocytic paraganglioma. Immunohistochemical examination was performed. Gangliocytic paragangliomas originating in the third or fourth portion of the duodenum, as in the present case, are extremely rare. Characteristic histologic features including epithelioid cells, spindle-shaped cells and ganglion-like cells were met. The majority of cases manifest with a similar benign behavior. Local resection of the tumor is recommended for these cases. An infrequent case of a gangliocytic paraganglioma located in the third portion of the duodenum, with a less common clinical presentation, is herein reported.

Space Vector Pulse Width Modulation of a Multi-Level Diode ...

African Journals Online (AJOL)

Space Vector Pulse Width Modulation of a Multi-Level Diode Clamped ... of MATLAB /SIMULINK modeling of the space vector pulse-width modulation and the ... two adjacent active vectors in determining the switching process of the multilevel ...

Attentional Focus and Grip Width Influences on Bench Press Resistance Training.

Science.gov (United States)

Calatayud, Joaquin; Vinstrup, Jonas; Jakobsen, Markus D; Sundstrup, Emil; Colado, JuanCarlos; Andersen, Lars L

2018-04-01

This study evaluated the influence of different attentional foci for varied grip widths in the bench press. Eighteen resistance-trained men were familiarized with the procedure and performed a one-repetition maximum (1RM) test during Session 1. In Session 2, they used three different standardized grip widths (100%, 150%, and 200% of biacromial width distance) in random order at 50% of 1RM while also engaged in three different attention focus conditions (external focus on the bench press, internal focus on pectoralis major muscles, and internal focus on triceps brachii muscles). Surface electromyography (EMG) signals were recorded from the triceps brachii and pectoralis major, and peak EMG of the filtered signals were normalized to maximum EMG of each muscle. Both grip width and focus influenced the muscle activity level, but there were no significant interactions between these variables. Exploratory analyses suggested that an internal focus may slightly (4%-6%) increase pectoralis major activity at wider grip widths and triceps brachii activity at narrower grip widths, but this should be confirmed or rejected in a study with a larger sample size or through a meta-analysis of research to date.

Analysis on Longitudinal Dose according to Change of Field Width

International Nuclear Information System (INIS)

Jung, Won Seok; Shin, Ryung Mi; Oh, Byung Cheon; Jo, Jun Young; Kim, Gi Chul; Choi, Tae Gu; Back, Jong Geal

2011-01-01

To analyze the accuracy of tumor volume dose following field width change, to check the difference of dose change by using self-made moving car, and to evaluate practical delivery tumor dose when tomotherapy in the treatment of organ influenced by breathing. By using self-made moving car, the difference of longitudinal movement (0.0 cm, 1.0 cm, 1.5 cm, 2.0 cm) was applied and compared calculated dose with measured dose according to change of field width (1.05 cm, 2.50 cm, 5.02 cm) and apprehended margin of error. Then done comparative analysis in degree of photosensitivity of DQA film measured by using Gafchromic EBT film. Dose profile and Gamma histogram were used to measure degree of photosensitivity of DQA film. When field width were 1.05 cm, 2.50 cm, 5.02 cm, margin of error of dose delivery coefficient was -2.00%, -0.39%, -2.55%. In dose profile of Gafchromic EBT film's analysis, the movement of moving car had greater motion toward longitudinal direction and as field width was narrower, big error increased considerably at high dose part compared to calculated dose. The more field width was narrowed, gamma index had a large considerable influence of moving at gamma histogram. We could check the difference of longitudinal dose of moving organ. In order to small field width and minimize organ moving due to breathing, it is thought to be needed to develop breathing control unit and fixation tool.

Study of off-momentum losses at the start of the ramp in the Large Hadron Collider

CERN Document Server

Wretborn, Sven Joel; Garcia Morales, Hector; Sjobaek, Kyrre Ness; CERN. Geneva. ATS Department

2017-01-01

At the start of the energy ramp at the LHC, any uncaptured beam is quickly lost on the momentum collimators. This causes significant instantaneous losses, and it is therefore important to understand these losses in detail in case they would become critical at the LHC itself or in future machines. This note aims at first analyzing data of these losses from the 2016 LHC run to quantify their features. Then, simulation methods are developed. First a simple but fast one-turn map model is used to study the phase space motion and the expected time profile of losses, after which SixTrack is used to provide a more complete simulation environment including all machine elements together with scattering in the collimators. A combined simulation, where first the Toy model is used to track particles for the first 11 s of the ramp, before they are handed over to SixTrack, is shown to be reasonably fast and to produce loss maps that qualitatively agree with the measurements. The time profile of the measured losses is used t...

A Collaborative Strategy for a Three Echelon Supply Chain with Ramp Type Demand, Deterioration and Inflation

Directory of Open Access Journals (Sweden)

Narayan Singh

2014-01-01

Full Text Available A supply chain system has been investigated in which a single manufacturer procures raw materials from a single supplier, processes them to produce finished products, and then delivers the products to a single retailer. The customer's demand rate is assumed to be time-sensitive in nature (ramp type that allows two-phase variation in the demand and production rate. Our adoption of ramp type demand reflects a real market demand for a newly launched product. Shortages are allowed with partial backlogging of demand (only for the retailer, i.e. the rest represent lost sales. The effects of inflation of the cost parameters and deterioration are also considered separately. We show that the total cost function is convex. Using this convexity, a simple algorithm is presented to determine the optimal order quantity and optimal cycle time for the total cost function. The results are discussed with numerical examples and particular cases of the model discussed briefly. A sensitivity analysis of the optimal solution with respect to the parameters of the system is carried out. (original abstract

How big is a food portion? A pilot study in Australian families.

Science.gov (United States)

Collins, Clare E; Bucher, Tamara; Taylor, Aimee; Pezdirc, Kristine; Lucas, Hannah; Watson, Jane; Rollo, Megan; Duncanson, Kerith; Hutchesson, Melinda J; Burrows, Tracy

2015-08-01

It is not known whether individuals can accurately estimate the portion size of foods usually consumed relative to standard serving sizes in national food selection guides. The aim of the present cross-sectional pilot study was to quantify what adults and children deem a typical portion for a variety of foods and compare these with the serving sizes specified in the Australian Guide to Healthy Eating (AGHE). Adults and children were independently asked to serve out their typical portion of 10 common foods (rice, pasta, breakfast cereal, chocolate, confectionary, ice cream, meat, vegetables, soft drink and milk). They were also asked to serve what they perceived a small, medium and large portion of each food to be. Each portion was weighed and recorded by an assessor and compared with the standard AGHE serving sizes. Twenty-one individuals (nine mothers, one father, 11 children) participated in the study. There was a large degree of variability in portion sizes measured out by both parents and children, with means exceeding the standard AGHE serving size for all items, except for soft drink and milk, where mean portion sizes were less than the AGHE serving size. The greatest mean overestimations were for pasta (155%; mean 116 g; range 94-139 g) and chocolate (151%; mean 38 g; range 25-50 g), each of which represented approximately 1.5 standard AGHE servings. The findings of the present study indicate that there is variability between parents' and children's estimation of typical portion sizes compared with national recommendations. SO WHAT? Dietary interventions to improve individuals' dietary patterns should target education regarding portion size.

Non-iterative determination of the stress-density relation from ramp wave data through a window

Science.gov (United States)

Dowling, Evan; Fratanduono, Dayne; Swift, Damian

2017-06-01

In the canonical ramp compression experiment, a smoothly-increasing load is applied the surface of the sample, and the particle velocity history is measured at interfaces two or more different distances into the sample. The velocity histories are used to deduce a stress-density relation by correcting for perturbations caused by reflected release waves, usually via the iterative Lagrangian analysis technique of Rothman and Maw. We previously described a non-iterative (recursive) method of analysis, which was more stable and orders of magnitude faster than iteration, but was subject to the limitation that the free surface velocity had to be sampled at uniform intervals. We have now developed more general recursive algorithms suitable for analyzing ramp data through a finite-impedance window. Free surfaces can be treated seamlessly, and the need for uniform velocity sampling has been removed. These calculations require interpolation of partially-released states using the partially-constructed isentrope, making them slower than the previous free-surface scheme, but they are still much faster than iterative analysis. This work was performed under the auspices of the U.S. Department of Energy by Lawrence Livermore National Laboratory under Contract DE-AC52-07NA27344.

Integrated modeling of plasma ramp-up in DIII-D ITER-like and high bootstrap current scenario discharges

Science.gov (United States)

Wu, M. Q.; Pan, C. K.; Chan, V. S.; Li, G. Q.; Garofalo, A. M.; Jian, X.; Liu, L.; Ren, Q. L.; Chen, J. L.; Gao, X.; Gong, X. Z.; Ding, S. Y.; Qian, J. P.; Cfetr Physics Team

2018-04-01

Time-dependent integrated modeling of DIII-D ITER-like and high bootstrap current plasma ramp-up discharges has been performed with the equilibrium code EFIT, and the transport codes TGYRO and ONETWO. Electron and ion temperature profiles are simulated by TGYRO with the TGLF (SAT0 or VX model) turbulent and NEO neoclassical transport models. The VX model is a new empirical extension of the TGLF turbulent model [Jian et al., Nucl. Fusion 58, 016011 (2018)], which captures the physics of multi-scale interaction between low-k and high-k turbulence from nonlinear gyro-kinetic simulation. This model is demonstrated to accurately model low Ip discharges from the EAST tokamak. Time evolution of the plasma current density profile is simulated by ONETWO with the experimental current ramp-up rate. The general trend of the predicted evolution of the current density profile is consistent with that obtained from the equilibrium reconstruction with Motional Stark effect constraints. The predicted evolution of βN , li , and βP also agrees well with the experiments. For the ITER-like cases, the predicted electron and ion temperature profiles using TGLF_Sat0 agree closely with the experimental measured profiles, and are demonstrably better than other proposed transport models. For the high bootstrap current case, the predicted electron and ion temperature profiles perform better in the VX model. It is found that the SAT0 model works well at high IP (>0.76 MA) while the VX model covers a wider range of plasma current ( IP > 0.6 MA). The results reported in this paper suggest that the developed integrated modeling could be a candidate for ITER and CFETR ramp-up engineering design modeling.

How much should I eat? A comparison of suggested portion sizes in the UK.

Science.gov (United States)

Lewis, Hannah B; Ahern, Amy L; Jebb, Susan A

2012-11-01

To identify and compare suggested food portion sizes in UK schemes. The study collated and compared suggested portion sizes from selected UK schemes intended both for general advice and weight-loss advice. Portion size schemes were included if they were relevant to the UK, provided actual portion size information, were intended for adults and were obtainable from the public domain in November 2010. Included schemes were from the food industry, non-governmental organisations and health-care professionals. Suggested portion sizes of foods occurring in at least one scheme for general advice and at least one scheme for weight loss were included. Own brand on-pack portion size labelling from a large UK-wide supermarket was added to represent portion size advice from UK food retailers. Not applicable. The suggested portion sizes in the weight-loss advice schemes were often concordant, as were the general advice schemes, except one general advice scheme from a non-governmental organisation which was more closely aligned with the portion sizes for weight loss. Overall there were substantial discrepancies between suggested portion sizes for muesli and crunchy breakfast cereals, rice, pasta and potatoes, meat, fish and pulses, whereas portion sizes for cooked vegetables, dried fruit, some breakfast cereals and cheese were broadly consistent. There is a lack of consistency in the portion sizes communicated to the public. An independent and authoritative scheme of suggested portion sizes for all foods, with distinct recommendations for general advice and for weight-loss advice, could be of benefit.

Process for forming a chromium diffusion portion and articles made therefrom

Science.gov (United States)

Helmick, David Andrew; Cavanaugh, Dennis William; Feng, Ganjiang; Bucci, David Vincent

2012-09-11

In one embodiment, a method for forming an article with a diffusion portion comprises: forming a slurry comprising chromium and silicon, applying the slurry to the article, and heating the article to a sufficient temperature and for a sufficient period of time to diffuse chromium and silicon into the article and form a diffusion portion comprising silicon and a microstructure comprising .alpha.-chromium. In one embodiment, a gas turbine component comprises: a superalloy and a diffusion portion having a depth of less than or equal to 60 .mu.m measured from the superalloy surface into the gas turbine component. The diffusion portion has a diffusion surface having a microstructure comprising greater than or equal to 40% by volume .alpha.-chromium.

21 CFR 14.27 - Determination to close portions of advisory committee meetings.

Science.gov (United States)

2010-04-01

... with the policy in this section. (2) A portion of a meeting may be closed only if the Commissioner... matters to be discussed in the closed portion. (c) Attendance at a closed portion of a meeting is governed... and unauthorized attendance does not enable other unauthorized persons to attend, nor does it, of...

Does Height to Width Ratio Correlate with Mean Volume in Gastropods?

Science.gov (United States)

Barriga, R.; Seixas, G.; Payne, J.

2012-12-01

Marine organisms' shell shape and size show important biological information. For example, shape and size can dictate how the organism ranges for food and escapes predation. Due to lack of data and analysis, the evolution of shell size in marine gastropods (snails) remains poorly known. In this study, I attempt to find the relationship between height to width ratio and mean volume. I collected height and width measurements from primary literature sources and calculated volume from these measurements. My results indicate that there was no correlation between height to width ratio and mean volume between 500 to 200 Ma, but there was a correlation between 200 Ma to present where there is a steady increase in both height to width ratio and mean volume. This means that shell shape was not an important factor at the beginning of gastropod evolution but after 200 Ma body size evolution was increasingly driven by the height to width ratio.

Fuel pin behavior under slow ramp-type transient-overpower conditions in the CABRI-FAST experiments

International Nuclear Information System (INIS)

Fukano, Yoshitaka; Onoda, Yuichi; Sato, Ikken; Charpenel, Jean

2009-01-01

In the CABRI-FAST experimental program, four in-pile tests were performed with slow power-ramp-type transient-overpower conditions (called hereafter as 'slow TOP') to study transient fuel pin behavior under inadvertent control rod withdrawal events in liquid metal cooled fast breeder reactors. Annular-pellet fuel pins were used in three tests, while a solid-pellet fuel pin was used in the other test. All of these pins were pre-irradiated in Phenix. The slow TOP test with a solid-pellet fuel pin was realized as a comparatory test against an existing test (E12) in the CABRI-2 program. In the CABRI-FAST test (BCF1), a power ramp rate of 3% Po/s was applied, while in the CABRI-2 test, 1% Po/s was adopted. Moreover, overpower condition was maintained for a few seconds beyond the observed pin failure in the BCF1 test. In spite of the different power ramp rates, evaluated fuel thermal conditions at the observed failure time are quite similar. The continued overpower condition in the BCF1 test resulted in gradual degradation of the pin structure providing information effective for evaluation of various accident scenarios. Three slow TOP tests with the annular fuel in the CABRI-FAST program resulted in no pin failure showing high failure threshold. Based on post-test examination data and a theoretical evaluation, it was concluded that intra-pin free spaces, such as central hole, macroscopic cracks and fuel-cladding gap effectively mitigated fuel cladding mechanical interaction. It was also clarified that cavity pressurization became effective only in case of very large amount of fuel melting. Furthermore, such cavity pressurization was effectively mitigated by a molten-fuel squirting into the upper blanket region pushing the blanket pellets upward. These CABRI FAST slow TOP tests, in combination with the existing CABRI and TREAT tests, provided an extended slow TOP test database with various fuel and transient conditions. (author)

Analysis of reduced widths and size

International Nuclear Information System (INIS)

Sharma, H.C.; Ram Raj; Nath, N.

1977-01-01

Recent data on S-wave neutron reduced widths for a large number of nuclei have been analysed nucleus-wise and the calculations for the degree of freedom of the associated (chi) 2 -distribution have been made using the Porter and Thomas procedure. It is noted that a number of nuclei can be fitted by a (chi) 2 -distribution with degree of freedom one, while there are few which are identified to follow a (chi) 2 -distribution with degree of freedom two and even more than two. The present analysis thus contradicts the usual presumption according to which the degree of freedom is taken to be always unity. An analytical attempt has also been made to ascertain the suitability of the data on reduced widths to be used for the analysis. These considerations are likely to modify the neutron cross-section evaluations. (author)

Dependence of effective spectrum width of synchrotron radiation on particle energy

Energy Technology Data Exchange (ETDEWEB)

Bagrov, V.G. [Tomsk State University, Department of Physics, Tomsk (Russian Federation); Institute of High Current Electronics, Tomsk (Russian Federation); University of Sao Paulo, Institute of Physics, Sao Paulo (Brazil); Gitman, D.M. [Tomsk State University, Department of Physics, Tomsk (Russian Federation); University of Sao Paulo, Institute of Physics, Sao Paulo (Brazil); P.N. Lebedev Physical Institute, Moscow (Russian Federation); Levin, A.D. [University of Sao Paulo, Institute of Physics, Sao Paulo (Brazil); Loginov, A.S.; Saprykin, A.D. [Tomsk State University, Department of Physics, Tomsk (Russian Federation)

2017-05-15

In the classical theory of synchrotron radiation, for the exact quantitative characterization of spectral properties, the concept of effective spectral width is introduced. In the first part of our work, published in EJPC 75 (2015), the effective spectral width as a function of the energy E of the radiating particle was obtained only in the ultra-relativistic approximation. In this article, which can be considered as a natural continuation of this work, a complete investigation is presented of the dependence of the effective width of the synchrotron radiation spectrum on energy for any values of E and for all the polarization components of the radiation. Numerical calculations were carried out for an effective width not exceeding 100 harmonics. (orig.)

Validation and Refinement of Prediction Models to Estimate Exercise Capacity in Cancer Survivors Using the Steep Ramp Test

NARCIS (Netherlands)

Stuiver, Martijn M.; Kampshoff, Caroline S.; Persoon, Saskia; Groen, Wim; van Mechelen, Willem; Chinapaw, Mai J. M.; Brug, Johannes; Nollet, Frans; Kersten, Marie-José; Schep, Goof; Buffart, Laurien M.

2017-01-01

Objective: To further test the validity and clinical usefulness of the steep ramp test (SRT) in estimating exercise tolerance in cancer survivors by external validation and extension of previously published prediction models for peak oxygen consumption (Vo2(peak)) and peak power output (W-peak).&

Turbulent transport regimes and the SOL heat flux width

Science.gov (United States)

Myra, J. R.; D'Ippolito, D. A.; Russell, D. A.

2014-10-01

Understanding the responsible mechanisms and resulting scaling of the scrape-off layer (SOL) heat flux width is important for predicting viable operating regimes in future tokamaks, and for seeking possible mitigation schemes. Simulation and theory results using reduced edge/SOL turbulence models have produced SOL widths and scalings in reasonable accord with experiments in many cases. In this work, we attempt to qualitatively and conceptually understand various regimes of edge/SOL turbulence and the role of turbulent transport in establishing the SOL heat flux width. Relevant considerations include the type and spectral characteristics of underlying instabilities, the location of the gradient drive relative to the SOL, the nonlinear saturation mechanism, and the parallel heat transport regime. Recent SOLT turbulence code results are employed to understand the roles of these considerations and to develop analytical scalings. We find a heat flux width scaling with major radius R that is generally positive, consistent with older results reviewed in. The possible relationship of turbulence mechanisms to the heuristic drift mechanism is considered, together with implications for future experiments. Work supported by US DOE grant DE-FG02-97ER54392.

Investigation of the ramp testing behaviour of fuel pins with different diameters

International Nuclear Information System (INIS)

Pott, G.; Herren, M.; Wigger, B.

1979-09-01

The aim of these experiments was the investigation of the influence of different fuel pin diameter on the ramp testing behaviour. Fuel elements with diameter between 10,75 and 15,6 mm and different cladding thickness had been ramptested in the HBWR (Halden Boiling Water Reactor) after preirradiated in the same facility. Fuel pins with the smallest diameter of 10,75 mm failed. This was indicated by fission gas release measurement. Metallographic examination showed these failure were caused by hydride blisters. A systematic influence of fuel pin diameter and cladding thickness on the ramptesting behaviour was not observed. (orig.) [de

Comparison of the equivalent width, the autocorrelation width, and the variance as figures of merit for XPS narrow scans

Energy Technology Data Exchange (ETDEWEB)

Singh, Bhupinder [Department of Chemistry and Biochemistry, C-100 BNSN, Brigham Young University, Provo, UT 84602 (United States); Velázquez, Daniel; Terry, Jeff [Department of Physics, Illinois Institute of Technology, Chicago, IL 60616 (United States); Linford, Matthew R., E-mail: mrlinford@chem.byu.edu [Department of Chemistry and Biochemistry, C-100 BNSN, Brigham Young University, Provo, UT 84602 (United States)

2014-12-15

Highlights: • We apply the equivalent and autocorrelation widths and variance to XPS narrow scans. • This approach is complementary to traditional peak fitting methods. • It is bias free and responsive to subtle chemical changes in spectra. • It has the potential for machine interpretation of spectra and quality control. • It has the potential for analysis of complex spectra and tracking charging/artifacts. - Abstract: X-ray photoelectron spectroscopy (XPS) is widely used in surface and materials laboratories around the world. It is a near surface technique, providing detailed chemical information about samples in the form of survey and narrow scans. To extract the maximum amount of information about materials it is often necessary to peak fit XPS narrow scans. And while indispensable to XPS data analysis, even experienced practitioners can struggle with their peak fitting. In our previous publication, we introduced the equivalent width (EW{sub XPS}) as both a possible machine automated method, one that requires less expert judgment for characterizing XPS narrow scans, and as an approach that may be well suited for the analysis of complex spectra. The EW{sub XPS} figure of merit was applied to four different data sets. However, as previously noted, other width functions are also regularly employed for analyzing functions. Here we evaluate two other width functions for XPS narrow scan analysis: the autocorrelation width (AW{sub XPS}) and the variance (σ{sub XPS}{sup 2}). These widths were applied to the same four sets of spectra studied before: (a) four C 1s narrow scans of ozone-treated carbon nanotubes (CNTs) (EW{sub XPS}: ∼2.11–2.16 eV, AW{sub XPS}: ∼3.9–4.1 eV, σ{sub XPS}{sup 2}: ∼5.0–5.2 eV, and a modified form of σ{sub XPS}{sup 2}, denoted σ{sub XPS}{sup 2*}: ∼6.3–6.8 eV), (b) silicon wafers with different oxide thicknesses (EW{sub XPS}: ∼1.5–2.9 eV, AW{sub XPS}: ∼2.28–4.9, and σ{sub XPS}{sup 2}: ∼0.7–4.9 eV), (iii

The effect of scattering interference term on the practical width

International Nuclear Information System (INIS)

Martins do Amaral, C.; Martinez, A.S.

2001-01-01

The practical width Γ p has an important application in the characterization of the resonance type for the calculation of neutron average cross sections. Previous treatments ignore the interference term χζ,x for the Doppler broadening function in the practical width calculation. In the present paper, a rational approximation for the χζ,x function is derived, using a modified asymptotic Pade method. A new approximation for Γ p is obtained. The results which are presented here provide evidence that the practical width as a function of temperature varies considerably with the inclusion of the interference term χζ,x

Capacitor charging FET switcher with controller to adjust pulse width

Science.gov (United States)

Mihalka, Alex M.

1986-01-01

A switching power supply includes an FET full bridge, a controller to drive the FETs, a programmable controller to dynamically control final output current by adjusting pulse width, and a variety of protective systems, including an overcurrent latch for current control. Power MOSFETS are switched at a variable frequency from 20-50 kHz to charge a capacitor load from 0 to 6 kV. A ferrite transformer steps up the DC input. The transformer primary is a full bridge configuration with the FET switches and the secondary is fed into a high voltage full wave rectifier whose output is connected directly to the energy storage capacitor. The peak current is held constant by varying the pulse width using predetermined timing resistors and counting pulses. The pulse width is increased as the capacitor charges to maintain peak current. A digital ripple counter counts pulses, and after the desired number is reached, an up-counter is clocked. The up-counter output is decoded to choose among different resistors used to discharge a timing capacitor, thereby determining the pulse width. A current latch shuts down the supply on overcurrent due to either excessive pulse width causing transformer saturation or a major bridge fault, i.e., FET or transformer failure, or failure of the drive circuitry.

A microelectrostatic repulsive-torque rotation actuator with two-width fingers

International Nuclear Information System (INIS)

Fan, Chao; He, Siyuan

2015-01-01

A microelectrostatic repulsive-torque rotation actuator with two-width fingers is presented. The actuator consists of finger-shaped electrodes and is made of two thin film layers, i.e. one movable layer and one fixed layer. There are two types of finger electrodes, namely constant-width and two-width fingers. The two-width finger has a narrow lower segment and a wide top segment. The constant-width finger has only the narrow lower segment. Each rotation finger has its corresponding aligned and unaligned fixed fingers. The electrostatic repulsive torque is generated and acts on the rotation fingers to rotate them up and away from the substrate. As a result, rotation is not limited by the gap between the movable and fixed layers and the ‘pull-in’ instability is avoided. Thus a large out-of-plane rotation and high operational stability can be achieved. The actuator is suitable for two-layer surface micromachining. The model of the actuator is developed. Prototypes are fabricated and tested. The experimental tests show that the actuator achieved a mechanical rotation of 7.65° at a driving voltage of 150 V. The settling time for a mechanical rotation of 5° is 5.7 ms. (paper)

Quantum numbers and decay widths of the psi (3684)

International Nuclear Information System (INIS)

Luth, V.; Boyarski, A.M.; Lynch, H.L.; Breidenbach, M.; Bulos, F.; Feldman, G.J.; Fryberger, D.; Hanson, G.; Hartill, D.L.; Jean-Marie, B.; Larsen, R.R.; Luke, D.; Morehouse, C.C.; Paterson, J.M.; Perl, M.L.; Pun, T.P.; Rapidis, P.; Richter, B.; Schwitters, R.F.; Tanenbaum, W.; Vannucci, F.; Abrams, G.S.; Chinowsky, W.; Friedberg, C.E.; Goldhaber, G.; Kadyk, J.A.; Litke, A.M.; Lulu, B.A.; Pierre, F.M.; Sadoulet, B.; Trilling, G.H.; Whitaker, J.S.; Winkelmann, F.C.; Wiss, J.E.

1975-01-01

Cross sections for e + e - →hadrons, e + e - , and μ + μ - near 3684 MeV are presented. The psi(3684) resonance is established as having the assignment J/sup PC/=1 -- . The mass is 3684+-5 MeV. The partial width for decay to electrons is GAMMA/sube/=2.1+-0.3 keV and the total width is GAMMA=228+-56 keV

How much should I eat? Estimation of meal portions in anorexia nervosa.

Science.gov (United States)

Milos, Gabriella; Kuenzli, Cornelia; Soelch, Chantal Martin; Schumacher, Sonja; Moergeli, Hanspeter; Mueller-Pfeiffer, Christoph

2013-04-01

Pathological concern regarding one's weight and weight gain is a crucial feature of anorexia nervosa. Consequently, anorexia nervosa patients often claim that they are uncertain regarding the amount of food they should eat. The present study investigated whether individuals with anorexia nervosa show an altered estimation of meal portion sizes and whether this estimation is modulated by an intent-to-eat instruction (where patients are asked to imagine having to eat the presented meal), meal type and meal portion size. Twenty-four women with anorexia nervosa and 27 healthy women estimated, using a visual analogue scale, the size of six different portions of three different meals, with and without intent-to-eat instructions. Subjects with anorexia nervosa estimated the size of small and medium meal portions (but not large meal servings) as being significantly larger, compared to estimates of healthy controls. The overestimation of small meal portions by anorexia nervosa subjects was significantly greater in the intent-to-eat, compared to general, condition. These findings suggest that disturbed perceptions associated with anorexia nervosa not only include interoceptive awareness (i.e., body weight and shape), but also extend to external disorder-related objects such as meal portion size. Specific therapeutic interventions, such as training regarding meal portion evaluation, could address these difficulties. Copyright © 2013. Published by Elsevier Ltd.

Correlation of H-mode barrier width and neutral penetration length

International Nuclear Information System (INIS)

Groebner, R.J.; Mahdavi, M.A.; Leonard, A.W.

2003-01-01

Pedestal studies in DIII-D find a good correlation between the width of the H-mode density barrier and the neutral penetration length. These results are obtained by comparing experimental density profiles to the predictions of an analytic model for the profile, obtained from the particle continuity equations for electrons and deuterium atoms. In its range of validity (edge temperature between 40-500 eV), the analytic model quantitatively predicts the observed decrease of the width as the pedestal density increases, the observed strong increase of the gradient of the density as the pedestal density increases and the observation that L-mode and H-mode profiles with the same pedestal density have very similar shapes. The width of the density barrier, measured from the edge of the electron temperature barrier, is the lower limit for the observed width of the temperature barrier. These results support the hypothesis that particle fueling provides the dominant control for the size of the H-mode transport barrier. (author)

Influence of body position on muscle deoxy[Hb+Mb] during ramp cycle exercise.

Science.gov (United States)

DiMenna, Fred J; Bailey, Stephen J; Jones, Andrew M

2010-09-30

We used near-infrared spectroscopy (NIRS) to test the hypothesis that body position alters the sigmoidal response profile of muscle fractional O(2) extraction (estimated using deoxy[Hb+Mb]) during incremental cycle exercise. Seven male subjects (mean±SD age 32±13 years) completed a ramp incremental cycling test to exhaustion (30W/min) in both the supine and upright body positions. The sigmoidal (as opposed to hyperbolic) model that provided the better fit to deoxy[Hb+Mb] data during upright cycling was also present for the supine response; however, the slope of the sigmoid was increased (upright: 0.052±0.012 vs. supine: 0.090±0.036%⋅%P(peak)(-1); Prate (upright: 83±8 vs. supine: 68±19%P(peak)(-1); Pchanges occurred in the absence of a leftward shift of the sigmoid. We also found a significantly greater deltaV(O)₂/deltaW slope above compared to below gas exchange threshold (GET) for both conditions (upright: 9.8±0.5 vs. 8.2±0.9; supine: 10.7±0.9 vs. 8.0±0.8) and for supine compared to upright cycling above GET. These findings suggest that the supine posture affects O₂ extraction and V(O)₂ kinetics to a greater extent as work rate progresses during ramp incremental exercise. Copyright 2010 Elsevier B.V. All rights reserved.

Hanford facility dangerous waste permit application, general information portion. Revision 3

International Nuclear Information System (INIS)

Sonnichsen, J.C.

1997-01-01

For purposes of the Hanford facility dangerous waste permit application, the US Department of Energy's contractors are identified as ''co-operators'' and sign in that capacity (refer to Condition I.A.2. of the Dangerous Waste Portion of the Hanford Facility Resource Conservation and Recovery Act Permit). Any identification of these contractors as an ''operator'' elsewhere in the application is not meant to conflict with the contractors' designation as co-operators but rather is based on the contractors' contractual status with the U.S. Department of Energy, Richland Operations Office. The Dangerous Waste Portion of the initial Hanford Facility Resource Conservation and Recovery Act Permit, which incorporated five treatment, storage, and/or disposal units, was based on information submitted in the Hanford Facility Dangerous Waste Permit Application and in closure plan and closure/postclosure plan documentation. During 1995, the Dangerous Waste Portion was modified twice to incorporate another eight treatment, storage, and/or disposal units; during 1996, the Dangerous Waste Portion was modified once to incorporate another five treatment, storage, and/or disposal units. The permit modification process will be used at least annually to incorporate additional treatment, storage, and/or disposal units as permitting documentation for these units is finalized. The units to be included in annual modifications are specified in a schedule contained in the Dangerous Waste Portion of the Hanford Facility Resource Conservation and Recovery Act Permit. Treatment, storage, and/or disposal units will remain in interim status until incorporated into the Permit. The Hanford Facility Dangerous Waste Permit Application is considered to be a single application organized into a General Information Portion (this document, DOE/RL-91-28) and a Unit-Specific Portion. The scope of the Unit-Specific Portion is limited to individual operating treatment, storage, and/or disposal units for which

Hanford facility dangerous waste permit application, general information portion. Revision 3

Energy Technology Data Exchange (ETDEWEB)

Sonnichsen, J.C.

1997-08-21

For purposes of the Hanford facility dangerous waste permit application, the US Department of Energy`s contractors are identified as ``co-operators`` and sign in that capacity (refer to Condition I.A.2. of the Dangerous Waste Portion of the Hanford Facility Resource Conservation and Recovery Act Permit). Any identification of these contractors as an ``operator`` elsewhere in the application is not meant to conflict with the contractors` designation as co-operators but rather is based on the contractors` contractual status with the U.S. Department of Energy, Richland Operations Office. The Dangerous Waste Portion of the initial Hanford Facility Resource Conservation and Recovery Act Permit, which incorporated five treatment, storage, and/or disposal units, was based on information submitted in the Hanford Facility Dangerous Waste Permit Application and in closure plan and closure/postclosure plan documentation. During 1995, the Dangerous Waste Portion was modified twice to incorporate another eight treatment, storage, and/or disposal units; during 1996, the Dangerous Waste Portion was modified once to incorporate another five treatment, storage, and/or disposal units. The permit modification process will be used at least annually to incorporate additional treatment, storage, and/or disposal units as permitting documentation for these units is finalized. The units to be included in annual modifications are specified in a schedule contained in the Dangerous Waste Portion of the Hanford Facility Resource Conservation and Recovery Act Permit. Treatment, storage, and/or disposal units will remain in interim status until incorporated into the Permit. The Hanford Facility Dangerous Waste Permit Application is considered to be a single application organized into a General Information Portion (this document, DOE/RL-91-28) and a Unit-Specific Portion. The scope of the Unit-Specific Portion is limited to individual operating treatment, storage, and/or disposal units for which

Effects of cooling portions of the head on human thermoregulatory response.

Science.gov (United States)

Katsuura, T; Tomioka, K; Harada, H; Iwanaga, K; Kikuchi, Y

1996-03-01

Seven healthy young male students participated in this study. Each subject sat on a chair in an anteroom at 25 degrees C for 30 min and then entered a climatic chamber, controlled at 40 degrees C and R.H. 50%, and sat on a chair for 90 min. Cooling of frontal portion including the region around the eyes (FC), occipital portion (OC), and temporal portion (TC) began after 50 min of entering. An experiment without head cooling (NC) was also made for the control measurement. Thermal comfort and thermal sensation were improved by head cooling, but response was the same regardless of portion cooled. Although rectal temperature, mean skin temperature and heart rate showed no significant effect due to head cooling, forearm skin blood flow (FBF), sweat rate (SR), and body weight loss (delta Wt) had a tendency to be depressed. FBF in FC and TC decreased during head cooling, but that in OC and NC did not change significantly, while SR in FC was depressed. delta Wt showed total sweating to decrease by FC and TC, and FC to have greater inhibitory effect on sweating than OC. Thermal strain was evaluated by the modified Craig Index (I(s)). I(s) in FC decreased significantly more than in NC. Cooling of other portions of the head had no significant effect on I(s). Cooling of the frontal portion of the head may thus be concluded to have the most effect on thermoregulatory response in a hot environment.

Repairing method and apparatus for weld portion of reactor core shroud

Energy Technology Data Exchange (ETDEWEB)

Tsujimura, Hiroshi; Tamai, Yasukata; Kurosawa, Koichi (Hitachi Ltd., Tokyo (Japan)); Toyota, Seiichi; Kikuchi, Toshikazu.

1993-12-07

A method of repairing a weld portion in a cylindrical reactor core shroud comprises a first step of inspecting a weld portion by an ultrasonic flow testing device from the surface of the reactor core shroud, a second step of applying repairing fabrication for cracked portion if it is discovered by the test and a third step of applying a surface modification to the fabricated portion after the repairing fabrication. As a result, repairing fabrication for the crack caused by stress corrosion crack or the like is enabled and reoccurrence of the stress corrosion crack in the repair fabrication portion can be prevented. Operator's exposure dose is minimized by shielding with reactor water or shielding plate. In a case of using the shielding plate, welding and surface improvement can be practiced in atmospheric air instead of water-submerged welding. Water does not intrude from the outside of the shroud and occurrence of penetration crack can be coped with. Further, it is possible to reduce cost and save labors for parts exchange by using the parts in common, to improve the operation efficiency. (N.H.).

Repairing method and apparatus for weld portion of reactor core shroud

International Nuclear Information System (INIS)

Tsujimura, Hiroshi; Tamai, Yasukata; Kurosawa, Koichi; Toyota, Seiichi; Kikuchi, Toshikazu.

1993-01-01

A method of repairing a weld portion in a cylindrical reactor core shroud comprises a first step of inspecting a weld portion by an ultrasonic flow testing device from the surface of the reactor core shroud, a second step of applying repairing fabrication for cracked portion if it is discovered by the test and a third step of applying a surface modification to the fabricated portion after the repairing fabrication. As a result, repairing fabrication for the crack caused by stress corrosion crack or the like is enabled and reoccurrence of the stress corrosion crack in the repair fabrication portion can be prevented. Operator's exposure dose is minimized by shielding with reactor water or shielding plate. In a case of using the shielding plate, welding and surface improvement can be practiced in atmospheric air instead of water-submerged welding. Water does not intrude from the outside of the shroud and occurrence of penetration crack can be coped with. Further, it is possible to reduce cost and save labors for parts exchange by using the parts in common, to improve the operation efficiency. (N.H.)

Prospects of power ramping and cycling supervision in Finnish power reactors

Energy Technology Data Exchange (ETDEWEB)

Antila, M; Kaikkonen, H T [Imatran Voima Oy, Helsinki (Finland); Mannola, E [Teollisuuden Voima Oy Industries Kraft Ab, Helsinki (Finland)

1983-06-01

Since 1977 2x440 MWe PWR and 2x660 MWe BWR nuclear power has been taken in operation in Finland, which until the middle of 1982 has given favourable fuel operating experiences from 10 reactor years. This paper describes the core supervision systems of the plants especially from the viewpoint of ramp surveillance and the potentials and needs to improve the supervision capability to meet the future needs in case more load follow operation is required. As a special feature for Imatran Voima is the demand of general basic understanding of the behaviour of Loviisa reactors' fuel in different operating conditions. A possibility to investigate the fuel seem to be power cycling tests in Loviisa reactors. (author)

Prospects of power ramping and cycling supervision in Finnish power reactors

International Nuclear Information System (INIS)

Antila, M.; Kaikkonen, H.T.; Mannola, E.

1983-01-01

Since 1977 2x440 MWe PWR and 2x660 MWe BWR nuclear power has been taken in operation in Finland, which until the middle of 1982 has given favourable fuel operating experiences from 10 reactor years. This paper describes the core supervision systems of the plants especially from the viewpoint of ramp surveillance and the potentials and needs to improve the supervision capability to meet the future needs in case more load follow operation is required. As a special feature for Imatran Voima is the demand of general basic understanding of the behaviour of Loviisa reactors' fuel in different operating conditions. A possibility to investigate the fuel seem to be power cycling tests in Loviisa reactors. (author)

Effects of injection nozzle exit width on rotating detonation engine

Science.gov (United States)

Sun, Jian; Zhou, Jin; Liu, Shijie; Lin, Zhiyong; Cai, Jianhua

2017-11-01

A series of numerical simulations of RDE modeling real injection nozzles with different exit widths are performed in this paper. The effects of nozzle exit width on chamber inlet state, plenum flowfield and detonation propagation are analyzed. The results are compared with that using an ideal injection model. Although the ideal injection model is a good approximation method to model RDE inlet, the two-dimensional effects of real nozzles are ignored in the ideal injection model so that some complicated phenomena such as the reflected waves caused by the nozzle walls and the reversed flow into the nozzles can not be modeled accurately. Additionally, the ideal injection model overpredicts the block ratio. In all the cases that stabilize at one-wave mode, the block ratio increases as the nozzle exit width gets smaller. The dual-wave mode case also has a relatively high block ratio. A pressure oscillation in the plenum with the same main frequency with the rotating detonation wave is observed. A parameter σ is applied to describe the non-uniformity in the plenum. σ increases as the nozzle exit width gets larger. Under some condition, the heat release on the interface of fresh premixed gas layer and detonation products can be strong enough to induce a new detonation wave. A spontaneous mode-transition process is observed for the smallest exit width case. Due to the detonation products existing in the premixed gas layer before the detonation wave, the detonation wave will propagate through reactants and products alternately, and therefore its strength will vary with time, especially near the chamber inlet. This tendency gets weaker as the injection nozzle exit width increases.

Maxillary palatal ramp prosthesis: A prosthodontic solution to manage mandibular deviation following surgery

Directory of Open Access Journals (Sweden)

Sampa Ray (Bhattacharya

2015-01-01

Full Text Available Mandibular resection following surgical treatment for neoplastic lesions of the oral cavity leads to numerous complications including altered mandibular movements, disfigurement, difficult in swallowing, impaired speech and articulation, and deviation of the mandible towards the resected site. Various prosthetic methods are employed to reduce or minimize mandibular deviation and improve and restore the lost functions and esthetic, like maxillomandibular fixation, implant supported prosthesis, removable mandibular guide flange prosthesis, and palatal based guidance restoration. This clinical report describes the rehabilitation of a patient following segmental mandibulectomy using palatal ramp prosthesis.

SM Higgs decay branching ratios and total Higgs width

CERN Multimedia

Daniel Denegri

2001-01-01

Upper: Higgs decay ratios as a function of Higgs mass. The largest branching ratio is not necessarily the most usefull one. The most usefull ones are gamma gamma bbar ZZ and WW as in those modes latter signal to background ratios can be achieved. Lower: Total Higgs decay width versus Higgs mass. At low masses the natural width is extremely small, thus observability depends on instrumental resolution primarily.

Penerapan Batas Ramp-Rate dengan Menggunakan Kombinasi Metode FDP (Forward Dynamic Programming dan QP (Quadratic Programming Pada Unit Commitment-Economic Dispatch

Directory of Open Access Journals (Sweden)

Riza Fahmi Andriyanto

2017-01-01

Full Text Available Kebutuhan akan energi listrik terus menigkat seiring dengan perkembangan teknologi. meningkatnya beban listrik ini harus diimbangi dengan penambahan daya yang dibangkitkan. Hal ini sangat berpengaruh pada penjadwalan unit pembangkit yang harus ditentukan dengan baik agar didapatkan pembangkitan yang optimal. Pada Tugas Akhir ini mengambil topik mengenai unit commitment dan economic dispatch dengan mempertimbangkan nilai dari batasan generator (ramp-rate. Metode yang digunakan adalah complete enumeration dengan forward dynamic programming pada unit commitment dan quadratic programming pada economic dispatch. Metode - metode tersebut diterapkan dalam pemrograman matlab sehingga dapat dijadikan suatu program perhitungan unit commitment dan economic dispatch dengan mempertimbangkan nilai batasan ramp-rate. Dengan metode tersebut, diharapkan permasalahan penjadwalan unit pembangkit dapat terselesaikan dengan baik dan optimal sehingga memperoleh total biaya pembangkitan yang ekonomis.

Legal Portion in Russian Inheritance Law

Science.gov (United States)

Inshina, Roza; Murzalimova, Lyudmila

2013-01-01

In this paper the authors describe the right to inherit as one of the basic human rights guaranteed by the Constitution of the Russian Federation. The state has set rules according to which after a person's death, his or her property is inherited by other persons. The Russian civil legislation establishes the institution of legal portions that is…

Quercus macrocarpa annual, early- and latewood widths as hydroclimatic proxies, southeastern Saskatchewan, Canada

International Nuclear Information System (INIS)

Vanstone, Jessica R; Sauchyn, David J

2010-01-01

Fluctuations in size of annual ring-widths of Quercus species suggest that environmental factors influence the size and density of vessels within the ring, either by acting as a limiting factor for growth or through fine tuning of the wood structure to environmental factors. The purpose of this study is to assess the potential of Q. macrocarpa to provide multiple dendroclimatic proxies for the Canadian Prairies, by investigating growth responses of annual, early- and latewood widths to regional climate variability. Results indicate that ring width chronologies, from southeastern Saskatchewan capture regional signals related to moisture and drought conditions. Correlations suggest that late-wood widths are more representative of annual ring-widths, than are early-wood widths, and are the best proxy of seasonal fluctuations in climate. Thus regression models that include latewood widths were able to account for more variance in the Palmer Drought Severity Index (PDSI) than when annual ring-widths are used as the only proxy. This study demonstrates that Q. macrocarpa can provide multiple dendroclimatic proxies for investigating large scale climatic fluctuations at annual and sub-annual time scales. It is novel in terms of sub-annual analysis of tree-rings in a region that previously lacked dendrochronological research.

Wind Power Ramp Events Prediction with Hybrid Machine Learning Regression Techniques and Reanalysis Data

Directory of Open Access Journals (Sweden)

Laura Cornejo-Bueno

2017-11-01

Full Text Available Wind Power Ramp Events (WPREs are large fluctuations of wind power in a short time interval, which lead to strong, undesirable variations in the electric power produced by a wind farm. Its accurate prediction is important in the effort of efficiently integrating wind energy in the electric system, without affecting considerably its stability, robustness and resilience. In this paper, we tackle the problem of predicting WPREs by applying Machine Learning (ML regression techniques. Our approach consists of using variables from atmospheric reanalysis data as predictive inputs for the learning machine, which opens the possibility of hybridizing numerical-physical weather models with ML techniques for WPREs prediction in real systems. Specifically, we have explored the feasibility of a number of state-of-the-art ML regression techniques, such as support vector regression, artificial neural networks (multi-layer perceptrons and extreme learning machines and Gaussian processes to solve the problem. Furthermore, the ERA-Interim reanalysis from the European Center for Medium-Range Weather Forecasts is the one used in this paper because of its accuracy and high resolution (in both spatial and temporal domains. Aiming at validating the feasibility of our predicting approach, we have carried out an extensive experimental work using real data from three wind farms in Spain, discussing the performance of the different ML regression tested in this wind power ramp event prediction problem.

The influence of front-of-pack nutrition information on consumers' portion size perceptions.

Science.gov (United States)

Brown, Hannah May; de Vlieger, Nienke; Collins, Clare; Bucher, Tamara

2017-08-01

Issue addressed Portion size guidance strategies have been suggested as an important component of weight management; therefore, the Health Star Rating (HSR) front-of-pack labels could influence consumers' portion-size decisions. However, this has not been investigated to date. This study aims to evaluate whether presenting energy content information and HSRs influences portion size self-selection of specific foods and meals. Methods Adults were randomly assigned to one of three experimental groups in this randomised controlled experiment. Each participant was given either a kJ/100g food label or a HSR label, or was given no information on nutrient composition. They were then asked to serve themselves an adequate portion of breakfast cereal (Kellogg's Nutri-Grain), fruit salad and chocolate, plus a three-component meal (chicken, fries and mixed vegetables). Portion serves and meal weights were compared between each experimental group using ANOVA and the discretionary foods were also compared with the Australian Guide to Healthy Eating (AGHE). Results Neither the kilojoule nor HSR information influenced the self-served portion size of foods or meal components. Mean self-served portion size of the discretionary foods were significantly greater than the standard serving sizes as specified in the AGHE. Conclusion Although food labels have the potential to assist consumers in making product choices, this study indicates that presenting nutrition information does not affect portion size decisions in young adults. So what? Strategies that assist consumers to choose appropriate portion sizes should be developed as a weight management tool.

Practical algorithms for linear boolean-width

NARCIS (Netherlands)

ten Brinke, C.B.; van Houten, F.J.P.; Bodlaender, H.L.

2015-01-01

In this paper, we give a number of new exact algorithms and heuristics to compute linear boolean decompositions, and experimentally evaluate these algorithms. The experimental evaluation shows that significant improvements can be made with respect to running time without increasing the width of the

Practical algorithms for linear Boolean-width

NARCIS (Netherlands)

ten Brinke, C.B.; van Houten, F.J.P.; Bodlaender, H.L.

2015-01-01

In this paper, we give a number of new exact algorithms and heuristics to compute linear boolean decompositions, and experimentally evaluate these algorithms. The experimental evaluation shows that significant improvements can be made with respect to running time without increasing the width of the

A 4 MA, 500 ns pulsed power generator CQ-4 for characterization of material behaviors under ramp wave loading.

Science.gov (United States)

Wang, Guiji; Luo, Binqiang; Zhang, Xuping; Zhao, Jianheng; Sun, Chengwei; Tan, Fuli; Chong, Tao; Mo, Jianjun; Wu, Gang; Tao, Yanhui

2013-01-01

A pulsed power generator CQ-4 was developed to characterize dynamic behaviors of materials under ramp wave loading, and to launch high velocity flyer plates for shock compression and hypervelocity impact experiments of materials and structures at Institute of Fluid Physics, China Academy of Engineering Physics. CQ-4 is composed of twenty capacitor and primary discharge switch modules with total capacitance of 32 μF and rated charging voltage of 100 kV, and the storage energy is transmitted by two top and bottom parallel aluminum plates insulated by twelve layers of polyester film with total thickness of 1.2 mm. Between capacitor bank and chamber, there are 72 peaking capacitors with total capacitance of 7.2 μF and rated voltage of 120 kV in parallel, which are connected with the capacitor bank in parallel. Before the load, there is a group of seven secondary self-breaking down switches connected with the total circuit in series. The peaking capacitors and secondary switches are used to shape the discharging current waveforms. For short-circuit, the peak current of discharging can be up to 3 ~ 4 MA and rise time varies from 470 ns to 600 ns when the charging voltages of the generator are from 75 kV to 85 kV. With CQ-4 generator, some quasi-isentropic compression experiments under ramp wave loadings are done to demonstrate the ability of CQ-4 generator. And some experiments of launching high velocity flyer plates are also done on CQ-4. The experimental results show that ramp wave loading pressure of several tens of GPa on copper and aluminum samples can be realized and the velocity of aluminum flyer plate with size of 10 mm × 6 mm × 0.35 mm can be accelerated to about 11 km/s and the velocity of aluminum flyer plate with size of 10 mm × 6 mm × 0.6 mm can be up to about 9 km/s, which show that CQ-4 is a good and versatile tool to realize ramp wave loading and shock compression for shock physics.

Dynamic compensation of the Silver self-powered neutron detector in the ramp program at the OSIRIS reactor

International Nuclear Information System (INIS)

Moulin, D.J.

1994-01-01

The Silver self-powered neutron detector (SPND) is a common detector used in the ramp program at the OSIRIS reactor. The Silver SPND signal is a reference during steady states, but its response is too slow for monitoring transient tests. In order to compensate for the inherent time delay a mathematical processing method of the Silver SPND signal was developed. Based on a convolution-type resolution of the kinetics equations, a dynamic compensation algorithm can be used for transient conditions as well as steady state conditions. A computer program reconstructs, in real-time, the dynamic neutron flux sensed by the Silver detector from the current measured between the emitter and the collector of the SPND. Although this method decreases slightly the signal-to-noise ratio, it maintains the SPND's characteristics and reduces the response time from about 10 minutes to less than 4 seconds for a step change in flux. This provides for prompt and accurate measurement of fuel rod power during ramp experiments in the OSIRIS reactor. This development makes the Silver SPND very suitable for many on-line monitoring applications

LHC Report: intensity ramp-up – familiar demons

CERN Multimedia

Mike Lamont for the LHC team

2015-01-01

The first 2015 scrubbing run ended on Friday, 3 July and successfully delivered a well-scrubbed machine ready for operation with a 50 ns beam. This opened the way for the first phase of the so-called beam intensity ramp-up. The last couple of weeks have seen the number of bunches increase from 3 to 476 per beam via periods of 50, 144 and 300 bunches per beam.   The graph plots the rate of LHC beam dumps due to single-event effects (SEE) versus beam luminosity. It is an indication of the importance of tackling this issue.   To verify the full and proper functioning of all systems, operators need at least 3 fills and 20 hours of stable beams without significant problems. After 20 hours, an extensive checklist is signed off by the system experts before the next step up in the number of bunches. The systems involved include magnet protection, radio-frequency, beam instrumentation, collimation, operations, feedback, beam dump and injection. Increasing the total beam intensity poses a numb...

Modeling Lane-Changing Behavior in Freeway Off-Ramp Areas from the Shanghai Naturalistic Driving Study

Directory of Open Access Journals (Sweden)

Lanfang Zhang

2018-01-01

Full Text Available The objective of this study is to investigate lane-changing characteristics in freeway off-ramp areas using Shanghai Naturalistic Driving Study (SH-NDS data, considering a four-lane freeway stretch in various traffic conditions. In SH-NDS, the behavior of drivers is observed unobtrusively in a natural setting for a long period of time. We identified 433 lane-changing events with valid time series data from the whole dataset. Based on the logit model developed to analyze the choice of target lanes, a likelihood analysis of lane-changing behavior was graphed with respect to three traffic conditions: free flow, medium flow, and heavy flow. The results suggested that lane-changing behavior of exiting vehicles is the consequence of the balance between route plan (mandatory incentive and expectation to improve driving condition (discretionary incentive. In higher traffic density, the latter seems to play a significant role. Furthermore, we found that lane-change from the slow lane to the fast lane would lead to higher speed variance value, which indicates a higher crash risk. The findings contribute to a better understanding on drivers’ natural driving behavior in freeway off-ramp areas and can provide important insight into road network design and safety management strategies.

Analysis of the Effects of a Flexible Ramping Ancillary Service Product on Power System Operations: Preprint

Energy Technology Data Exchange (ETDEWEB)

Krad, Ibrahim; Ibanez, Eduardo; Ela, Erik

2015-10-19

The recent increased interest in utilizing variable generation (VG) resources such as wind and solar in power systems has motivated investigations into new operating procedures. Although these resources provide desirable value to a system (e.g., no fuel costs or emissions), interconnecting them provides unique challenges. Their variable, non-controllable nature in particular requires significant attention, because it directly results in increased power system variability and uncertainty. One way to handle this is via new operating reserve schemes. Operating reserves provide upward and downward generation and ramping capacity to counteract uncertainty and variability prior to their realization. For instance, uncertainty and variability in real-time dispatch can be accounted for in the hour-ahead unit commitment. New operating reserve methodologies that specifically account for the increased variability and uncertainty caused by VG are currently being investigated and developed by academia and industry. This paper examines one method inspired by the new operating reserve product being proposed by the California Independent System Operator. The method is based on examining the potential ramping requirements at any given time and enforcing those requirements via a reserve demand curve in the market-clearing optimization as an additional ancillary service product.

Hydrogeology of the unsaturated zone, North Ramp area of the Exploratory Studies Facility, Yucca Mountain, Nevada

Energy Technology Data Exchange (ETDEWEB)

Rousseau, J.P.; Kwicklis, E.M.; Gillies, D.C. [eds.

1999-03-01

Yucca Mountain, in southern Nevada, is being investigated by the US Department of Energy as a potential site for a repository for high-level radioactive waste. This report documents the results of surface-based geologic, pneumatic, hydrologic, and geochemical studies conducted during 1992 to 1996 by the US Geological Survey in the vicinity of the North Ramp of the Exploratory Studies Facility (ESF) that are pertinent to understanding multiphase fluid flow within the deep unsaturated zone. Detailed stratigraphic and structural characteristics of the study area provided the hydrogeologic framework for these investigations. Shallow infiltration is not discussed in detail in this report because the focus in on three major aspects of the deep unsaturated-zone system: geologic framework, the gaseous-phase system, and the aqueous-phase system. However, because the relation between shallow infiltration and deep percolation is important to an overall understanding of the unsaturated-zone flow system, a summary of infiltration studies conducted to date at Yucca Mountain is provided in the section titled Shallow Infiltration. This report describes results of several Site Characterization Plan studies that were ongoing at the time excavation of the ESF North Ramp began and that continued as excavation proceeded.

Stream water responses to timber harvest: Riparian buffer width effectiveness

Science.gov (United States)

Barton D. Clinton

2011-01-01

Vegetated riparian buffers are critical for protecting aquatic and terrestrial processes and habitats in southern Appalachian ecosystems. In this case study, we examined the effect of riparian buffer width on stream water quality following upland forest management activities in four headwater catchments. Three riparian buffer widths were delineated prior to cutting; 0m...

Effect of transmitter turn-off time on transient soundings

Science.gov (United States)

Fitterman, D.V.; Anderson, W.L.

1987-01-01

A general procedure for computing the effect of non-zero turn-off time on the transient electromagnetic response is presented which can be applied to forward and inverse calculation methods for any transmitter-receiver configuration. We consider in detail the case of a large transmitter loop which has a receiver coil located at the center of the loop (central induction or in-loop array). For a linear turn-off ramp of width t0, the voltage response is shown to be the voltage due to an ideal step turn-off averaged over windows of width t0. Thus the effect is similar to that obtained by using averaging windows in the receiver. In general when time zero is taken to be the end of the ramp, the apparent resistivity increases for a homogeneous half-space over a limited time range. For time zero taken to be the start of the ramp the apparent resistivity is affected in the opposite direction. The effect of the ramp increases with increasing t0 and first-layer resistivity, is largest during the intermediate stage, and decreases with increasing time. It is shown that for a ramp turn-off, there is no effect in the early and late stages. For two-layered models with a resistive first layer (??1>??2), the apparent resistivity is increased in the intermediate stage. When the first layer is more conductive than the second layer (??1interpretation as shown by field examples; the influence is the greatest on near-surface layer parameters. ?? 1987.

Évaluation expérimentale du maintien en état de fonctionnement d’une rampe combinée d’aspersion mécanisée dans le contexte tunisien

Directory of Open Access Journals (Sweden)

Youssef M'SADAK

2017-09-01

Full Text Available The objective of this study is to diagnose the field operation of a combined ramp during its first campaign at a large private farm, located in the Borj Elamri delegation, governorate of Manouba (North of Tunisia, to shed light on the quality of the irrigation obtained. This work was devoted to the evaluation of the water distribution, the coefficient of uniformity and possible corrections of the adopted nozzle distribution according to the plan indicated by the manufacturer. On the other hand, we verified conformity between theoretical and actual nozzle plan by placing nozzles at their correct position on the ramp and also tested the uniform distribution of the water. The uniformity tests carried out on the side of the ramp covered a range of prevailing wind speeds of 1 to 6 m/s and a pressure range of 1.6 to 3.5 bars. The operation diagnostics detected that the studied system (pivot-ramp presented a simple dual-function nozzles (different from the generally used double nozzle plan with nozzles in good condition with a slight deviation of the flows at the level of the pivot and the front ramp. The linear mode of this system is less wind sensitive and less energy-intensive than the pivot mode. The latter revealed an overall coefficient of uniformity of about 83%, lower than that of the linear mode (86%. Finally, the future use of such a mechanized sprinkler system is not the optimum solution, due in particular to their complexity of design, assembly, operation and use.

Attention demanding tasks during treadmill walking reduce step width variability in young adults

Directory of Open Access Journals (Sweden)

Troy Karen L

2005-08-01

Full Text Available Abstract Background The variability of step time and step width is associated with falls by older adults. Further, step time is significantly influenced when performing attention demanding tasks while walking. Without exception, step time variability has been reported to increase in normal and pathologically aging older adults. Because of the role of step width in managing frontal plane dynamic stability, documenting the influence of attention-demanding tasks on step width variability may provide insight to events that can disturb dynamic stability during locomotion and increase fall risk. Preliminary evidence suggests performance of an attention demanding task significantly decreases step width variability of young adults walking on a treadmill. The purpose of the present study was to confirm or refute this finding by characterizing the extent and direction of the effects of a widely used attention demanding task (Stroop test on the step width variability of young adults walking on a motorized treadmill. Methods Fifteen healthy young adults walked on a motorized treadmill at a self-selected velocity for 10 minutes under two conditions; without performing an attention demanding task and while performing the Stroop test. Step width of continuous and consecutive steps during the collection was derived from the data recorded using a motion capture system. Step width variability was computed as the standard deviation of all recorded steps. Results Step width decreased four percent during performance of the Stroop test but the effect was not significant (p = 0.10. In contrast, the 16 percent decrease in step width variability during the Stroop test condition was significant (p = 0.029. Conclusion The results support those of our previous work in which a different attention demanding task also decreased step width variability of young subjects while walking on a treadmill. The decreased step width variability observed while performing an attention

Analysis of power ramp rate and minimum power controllability of the MMS model for a plant dynamics analysis of a Prototype SFR

International Nuclear Information System (INIS)

Kim, Eui Kwang; Kim, Dehee; Joo, Hyungkook; Lee, Taeho

2014-01-01

A full plant dynamic model was developed for a prototype SFR using the Modular Modeling System (MMS). It includes the modeling of various subsystems such as the neutronics, primary and intermediate sodium systems of the NSSS, steam and water systems of the BOP, BOP controls, and the supervisory plant controls. The NSSS model is subdivided into component models, such as a Core, IHXs, Pumps, SGs, and the rest of the NSSS loop model. The BOP model is subdivided into a steam subsystem, feedwater subsystem, and preheater subsystem. Plant transient tests were performed to study the operational considerations. It includes varying the power ramp rate and studying the controllability at minimum power. Plant transient tests were performed to study operational considerations by using the MMS model for a prototype SFR. It includes varying the power ramp rate, studying the controllability at the minimum power set point. At a power ramp rate of higher than 2%, the steam temperature has a large deviation from the target. As the power set point decreases, the PHTS hot leg temperature and steam temperature tend to have higher deviations. After further refinement of the MMS model, it can be useful for developing the plant operation logics of the prototype SFR

Exotic meson decay widths using lattice QCD

International Nuclear Information System (INIS)

Cook, M. S.; Fiebig, H. R.

2006-01-01

A decay width calculation for a hybrid exotic meson h, with J PC =1 -+ , is presented for the channel h→πa 1 . This quenched lattice QCD simulation employs Luescher's finite box method. Operators coupling to the h and πa 1 states are used at various levels of smearing and fuzzing, and at four quark masses. Eigenvalues of the corresponding correlation matrices yield energy spectra that determine scattering phase shifts for a discrete set of relative πa 1 momenta. Although the phase shift data is sparse, fits to a Breit-Wigner model are attempted, resulting in a decay width of about 60 MeV when averaged over two lattice sizes having a lattice spacing of 0.07 fm

Width of electromagnetic wave instability spectrum in tungsten plate

International Nuclear Information System (INIS)

Rinkevich, A.B.

1995-01-01

Based on the study of high-frequency signal modulation and spectrum analysis of the envelope a measurement of spectrum width for electromagnetic wave instability was carried out under conditions of current pulse action on tungsten plate in magnetic field. The existence of amplitude-frequency wave modulation was revealed. The width of current disturbance spectrum in a specimen was evaluated. Current disturbances are shown to cause the instability of electromagnetic wave. 11 refs.; 6 figs

Estimating the Spectral Width of a Narrowband Optical Signal

DEFF Research Database (Denmark)

Lading, Lars; Skov Jensen, A.

1980-01-01

Methods for estimating the spectral width of a narrowband optical signal are investigated. Spectral analysis and Fourier spectroscopy are compared. Optimum and close-to-optimum estimators are developed under the constraint of having only one photodetector.......Methods for estimating the spectral width of a narrowband optical signal are investigated. Spectral analysis and Fourier spectroscopy are compared. Optimum and close-to-optimum estimators are developed under the constraint of having only one photodetector....

Comparison of tibiofemoral joint space width measurements from standing CT and fixed flexion radiography.

Science.gov (United States)

Segal, Neil A; Frick, Eric; Duryea, Jeffrey; Nevitt, Michael C; Niu, Jingbo; Torner, James C; Felson, David T; Anderson, Donald D

2017-07-01

The objective of this project was to determine the relationship between medial tibiofemoral joint space width measured on fixed-flexion radiographs and the three-dimensional joint space width distribution on low-dose, standing CT (SCT) imaging. At the 84-month visit of the Multicenter Osteoarthritis Study, 20 participants were recruited. A commercial SCT scanner for the foot and ankle was modified to image knees while standing. Medial tibiofemoral joint space width was assessed on radiographs at fixed locations from 15% to 30% of compartment width using validated software and on SCT by mapping the distances between three-dimensional subchondral bone surfaces. Individual joint space width values from radiographs were compared with three-dimensional joint space width values from corresponding sagittal plane locations using paired t-tests and correlation coefficients. For the four medial-most tibiofemoral locations, radiographic joint space width values exceeded the minimal joint space width on SCT by a mean of 2.0 mm and were approximately equal to the 61st percentile value of the joint space width distribution at each respective sagittal-plane location. Correlation coefficients at these locations were 0.91-0.97 and the offsets between joint space width values from radiographs and SCT measurements were consistent. There were greater offsets and variability in the offsets between modalities closer to the tibial spine. Joint space width measurements on fixed-flexion radiographs are highly correlated with three-dimensional joint space width from SCT. In addition to avoiding bony overlap obscuring the joint, a limitation of radiographs, the current study supports a role for SCT in the evaluation of tibiofemoral OA. © 2017 Orthopaedic Research Society. Published by Wiley Periodicals, Inc. J Orthop Res 35:1388-1395, 2017. © 2017 Orthopaedic Research Society. Published by Wiley Periodicals, Inc.

Investigation of strut-ramp injector in a Scramjet combustor: Effect of strut geometry, fuel and jet diameter on mixing characteristics

Energy Technology Data Exchange (ETDEWEB)

Soni, Rahul Kumar; De, Ashoke De [Indian Institute of Technology Kanpur, Kanpur (India)

2017-03-15

The strut-based injector has been found to be one of the most promising injector designs for a supersonic combustor, offering enhanced mixing of fuel and air. The mixing and flow field characteristics of the straight (SS) and Tapered strut (TS), with fixed ramp angle and height at free stream Mach number 2 in conjunction with fuel injection at Mach 2.3 have been investigated numerically and reported. In the present investigation, hydrogen (H{sub 2}) and ethylene (C{sub 2}H{sub 4}) are injected in oncoming supersonic flow from the back of the strut, where jet to free stream momentum ratio is maintained at 0.79 and 0.69 for H2 and C{sub 2}H{sub 4}, respectively. The predicted wall static pressure and species mole fractions at various downstream locations are compared with the experimental data for TS case with 0.6 mm jet diameter and found to be in good agreement. Further, the effect of jet diameter and strut geometry on the near field mixing in strut ramp configuration is discussed for both the fuels. The numerical results are assessed based on various parameters for the performance evaluation of different strut ramp configurations. The SS configuration for both the injectant has been found to be an optimum candidate; also it is observed that for higher jet diameter larger combustor length is required to achieve satisfactory near field mixing.

Statistical analysis of s-wave neutron reduced widths

International Nuclear Information System (INIS)

Pandita Anita; Agrawal, H.M.

1992-01-01

The fluctuations of the s-wave neutron reduced widths for many nuclei have been analyzed with emphasis on recent measurements by a statistical procedure which is based on the method of maximum likelihood. It is shown that the s-wave neutron reduced widths of nuclei follow single channel Porter Thomas distribution (x 2 -distribution with degree of freedom ν = 1) for most of the cases. However there are apparent deviations from ν = 1 and possible explanation and significance of this deviation is given. These considerations are likely to modify the evaluation of neutron cross section. (author)

Alluvial cover controlling the width, slope and sinuosity of bedrock channels

Science.gov (United States)

Turowski, Jens Martin

2018-02-01

Bedrock channel slope and width are important parameters for setting bedload transport capacity and for stream-profile inversion to obtain tectonics information. Channel width and slope development are closely related to the problem of bedrock channel sinuosity. It is therefore likely that observations on bedrock channel meandering yields insights into the development of channel width and slope. Active meandering occurs when the bedrock channel walls are eroded, which also drives channel widening. Further, for a given drop in elevation, the more sinuous a channel is, the lower is its channel bed slope in comparison to a straight channel. It can thus be expected that studies of bedrock channel meandering give insights into width and slope adjustment and vice versa. The mechanisms by which bedrock channels actively meander have been debated since the beginning of modern geomorphic research in the 19th century, but a final consensus has not been reached. It has long been argued that whether a bedrock channel meanders actively or not is determined by the availability of sediment relative to transport capacity, a notion that has also been demonstrated in laboratory experiments. Here, this idea is taken up by postulating that the rate of change of both width and sinuosity over time is dependent on bed cover only. Based on the physics of erosion by bedload impacts, a scaling argument is developed to link bedrock channel width, slope and sinuosity to sediment supply, discharge and erodibility. This simple model built on sediment-flux-driven bedrock erosion concepts yields the observed scaling relationships of channel width and slope with discharge and erosion rate. Further, it explains why sinuosity evolves to a steady-state value and predicts the observed relations between sinuosity, erodibility and storm frequency, as has been observed for meandering bedrock rivers on Pacific Arc islands.