Techno-economic study on conversion of SAFARI-1 to LEU silicide fuel

International Nuclear Information System (INIS)

Ball, G.; Malherbe, F.J.

2004-01-01

This paper marks the conclusion of the techno-economic study into the conversion of SAFARI-1 reactor in South Africa to LEU silicide fuel. Several different fuel types were studied and their characteristics compared to the current HEU fuel. The technical feasibility of operating SAFARI-1 with the different fuels as well as the overall economic impact of the fuels is discussed and conclusions drawn.(author)

Evaluation of In-Core Fuel Management for the Transition Cores of RSG-GAS Reactor to Full-Silicide Core

International Nuclear Information System (INIS)

S, Tukiran; MS, Tagor; P, Surian

2003-01-01

The core conversion of RSG-GAS reactor from oxide to silicide core with meat density of 2.96 gU/cc has been done. The core-of RSG-GAS reactor has been operated full core of silicide fuels which is started with the mixed core of oxide-silicide start from core 36. Based on previous work, the calculated core parameter for the cores were obtained and it is needed 9 transition cores (core 36 - 44) to achieve a full-silicide core (core 45). The objective of this work is to acquire the effect of the increment of the number of silicide fuel on the core parameters. Conversion core was achieved by transition cores mixed oxide-silicide fuels. Each transition core is calculated and measured core parameter such as, excess reactivity and shutdown margin. Calculation done by Batan-EQUIL-2D code and measurement of the core parameters was carried out using the method of compensation of couple control rods. The results of calculation and experiment shows that the excess reactivity trends lower with the increment of the number of silicide fuel in the core. However, the shutdown margin is not change with the increment of the number of silicide fuel. Therefore, the transition cores can be operated safely to a full-silicide core

Neutronic design of mixed oxide-silicide cores for the core conversion of rsg-gas reactor

International Nuclear Information System (INIS)

Sembiring, Tagor Malem; Tukiran; Pinem surian; Febrianto

2001-01-01

The core conversion of rsg-gas reactor from an all-oxide (U 3 O 8 -Al) core, through a series of mixed oxide-silicide core, to an all-silicide (U 3 Si 2 -Al) core for the same meat density of 2.96 g U/cc is in progress. The conversion is first step of the step-wise conversion and will be followed by the second step that is the core conversion from low meat density of silicide core, through a series of mixed lower-higher density of silicide core, to an all-higher meat density of 3.55 g/cc core. Therefore, the objectives of this work is to design the mixed cores on the neutronic performance to achieve safety a first full-silicide core for the reactor with the low uranium meat density of 2.96gU/cc. The neutronic design of the mixed cores was performed by means of Batan-EQUIL-2D and Batan-3DIFF computer codes for 2 and 3 dimension diffusion calculation, respectively. The result shows that all mixed oxide-silicide cores will be feasible to achieve safety a fist full-silicide core. The core performs the same neutronic core parameters as those of the equilibrium silicide core. Therefore, the reactor availability and utilization during the core conversion is not changed

Pilot plant production at Riso of LEU silicide fuel for the Danish reactor DR3

International Nuclear Information System (INIS)

Toft, P.; Borring, J.; Adolph, E.

1988-01-01

A pilot plant for fabricating LEU silicide fuel elements has been established at Riso National Laboratory. Three test elements for the Danish reactor DR3 have been fabricated, based on 19.88% enriched U 3 Si 2 powder that has been purchased elsewhere. The pilot plant has been set up and 3 test elements fabricated without any major difficulties

Neutronic analysis of the JMTR with LEU fuel and burnable poison

Energy Technology Data Exchange (ETDEWEB)

Nagaoka, Yoshiharu; Oyamada, Rokuro [Japan Atomic Energy Research Institute, Oarai-machi Ibaraki-ken (Japan); Matos, J E; Woodruff, W L [Argonne National Laboratory, Argonne, IL (United States)

1985-07-01

The results of neutronics calculations are presented for the JMTR equilibrium core with LEU silicide fuel, boron and cadmium burnable poisons in the sideplates, and a cycle length of 24 days instead of 11 days with the current HEU fuel. The data indicate that several options are feasible provided that silicide fuels with high uranium densities are successfully demonstrated and licensed (author)

Neutronic analysis of the JMTR with LEU fuel and burnable poison

International Nuclear Information System (INIS)

Nagaoka, Yoshiharu; Oyamada, Rokuro; Matos, J.E.; Woodruff, W.L.

1985-01-01

The results of neutronics calculations are presented for the JMTR equilibrium core with LEU silicide fuel, boron and cadmium burnable poisons in the sideplates, and a cycle length of 24 days instead of 11 days with the current HEU fuel. The data indicate that several options are feasible provided that silicide fuels with high uranium densities are successfully demonstrated and licensed (author)

Neutronic design of the RSG-GAS silicide core

Energy Technology Data Exchange (ETDEWEB)

Sembiring, T.M.; Kuntoro, I.; Hastowo, H. [Center for Development of Research Reactor Technology National Nuclear Energy Agency BATAN, PUSPIPTEK Serpong Tangerang, 15310 (Indonesia)

2002-07-01

The objective of core conversion program of the RSG-GAS multipurpose reactor is to convert the fuel from oxide, U{sub 3}O{sub 8}-Al to silicide, U{sub 3}Si{sub 2}-Al. The aim of the program is to gain longer operation cycle by having, which is technically possible for silicide fuel, a higher density. Upon constraints of the existing reactor system and utilization, an optimal fuel density in amount of 3.55 g U/cc was found. This paper describes the neutronic parameter design of the silicide equilibrium core and the design of its transition cores as well. From reactivity control point of view, a modification of control rod system is also discussed. All calculations are carried out by means of diffusion codes, Batan-EQUIL-2D, Batan-2DIFF and -3DIFF. The silicide core shows that longer operation cycle of 32 full power days can be achieved without decreasing the safety criteria and utilization capabilities. (author)

Comparison of the FRM-II HEU design with an alternative LEU design. Attachment

International Nuclear Information System (INIS)

Hanan, N.A.; Mo, S.C.; Smith, R.S.; Matos, J.E.

2004-01-01

After presentation of the foregoing paper by Dr. Nelson Hanan of Argonne National Laboratory (ANL) proposing an alternative LEU core with one fuel ring and a power level of 33 MW, a presentation was made by Dr. Klaus Boning of the Technical University of Munich comparing the FRM-II HEU design with an LEU design by Tlm that had two fuel rings and a power level of 40 MW. Dr. Boning raised the following issues concerning the use of LEU fuel in FRM-H reactor designs: (1) qualification of HEU and LEU silicide fuels, (2) gamma heating in the heavy water reflector, (3) the radiological consequences of hypothetical accidents, and (4) cost and schedule. These issues are addressed in this Attachment. In his presentation, Dr. Hanan mentioned that ANL was also investigating other LEU designs. This work led to a second alternative LEU design that has the same neutron flux performance (8 x 10 14 n/cm 2 /s peak neutron flux in the reflector) and the same fuel lifetime (50 full power days) as the HEU design, but uses LEU silicide fuel with a uranium density of only 4.5 g/cm 3 . This design was achieved by using a fuel plate that has a fuel meat thickness of 0.76 mm, a cladding thickness of 0.38 mm, and a water channel gap of 2.2 mm. A comparison is shown of the main characteristics of this second alternative LEU design with those of the FRM-II HEU design. The ANL core again has one fuel ring with the same dimensions. With this LEU design, a two stage process is no longer necessary because LEU silicide fuel with a uranium density of 4.5 g/cm 3 is fully qualified, licensable, and available now for use in a high flux reactor such as the FRM-II

Neutronic analysis of the JMTR with LEU fuel and burnable poison

International Nuclear Information System (INIS)

Nagaoka, Yoshiharu; Oyamada, Rokuro; Matos, J.E.; Woodruff, W.L.

1984-01-01

The results of neutronics calculations are presented for the JMTR equilibrium core with LEU silicide fuel, boron and cadmium burnable poisons in the sideplates, and a cycle length of 24 days instead of 11 days with the current HEU fuel. The data indicate that several options are feasible provided that silicide fuels with high uranium densities are successfully demonstrated and licensed. 2 refs., 10 figs., 5 tabs

Measurements of the HEU and LEU in-core spectra at the Ford Nuclear Reactor

Energy Technology Data Exchange (ETDEWEB)

Wehe, D K [Oak Ridge National Laboratory, Oak Ridge, TN (United States); King, J S; Lee, J C; Martin, W R [Department of Nuclear Engineering, University of Michigan, Ann Arbor, MI (United States)

1985-07-01

The Ford Nuclear Reactor (FNR) at the University of Michigan has been serving as the test site for a low-enriched uranium (LEU) fuel whole-core demonstration. As part of the experimental program, the differential neutron spectrum has been measured in a high-enriched uranium (HEU) core and an LEU core. The HEU and LEU spectra were determined by unfolding the measured activities of foils that were irradiated in the reactor. When the HEU and LEU spectra are compared from meV to 10 MeV, significant differences between the two spectra are apparent below 10 eV. These are probably caused by the additional {sup 238}U resonance absorption in the LEU fuel. No measurable difference occurs in the shape of the spectra above MeV. (author)

Progress on LEU very high density fuel and target development in Argentina

International Nuclear Information System (INIS)

Balart, S.; Cabot, P.; Calzetta, O.; Duran, A.; Garces, J.; Hermida, J.D.; Manzini, A.; Pasqualini, E.; Taboada, H.

2006-01-01

Since last RRFM meeting, CNEA has continued on new LEU fuel and target development activities. Main goals are the plan to convert our RA-6 reactor from HEU to a new LEU core, to get a comprehensive understanding of U-Mo/Al compounds phase formation in dispersed and monolithic fuels, to develop possible solutions to VHD dispersed and monolithic fuels technical problems, to optimize techniques to recover U from silicide scrap samples as cold test for radiowaste separation for final conditioning of silicide spent fuels. and to improve the diffusion of LEU target and radiochemical technology for radioisotope production. Future plans include: - Completion of the RA-6 reactor conversion to LEU; - Improvement on fuel development and production facilities to implement new technologies, including NDT techniques to assess bonding quality; - Irradiation of miniplates and full scale fuel assembly at RA-3 and plans to perform irradiation on higher power and temperature regime reactors; - Optimization of LEU target and radiochemical techniques for radioisotope production. (author)

Analysis of reactivity accidents of the RSG-GAS core with silicide fuel

International Nuclear Information System (INIS)

Tukiran

2002-01-01

The fuels of RSG-GAS reactor is changed from uranium oxide to uranium silicide. For time being, the fuel of RSG-GAS core are mixed up between oxide and silicide fuels with 250 gr of loading and 2.96 g U/cm 3 of density, respectively. While, silicide fuel with 300 gr of loading is still under research. The advantages of silicide fuels are can be used in high density, so that, it can be stayed longer in the core at higher burn-up, therefore, the length of cycle is longer. The silicide fuel in RSG-GAS core is used in step-wise by using mixed up core. Firstly, it is used silicide fuel with 250 gr of loading and then, silicide fuel with 300 gr of loading (3.55 g U/cm 3 of density). In every step-wise of fuel loading must be analysed its safety margin. In this occasion, it is analysed the reactivity accident of RSG-GAS core with 300 gr of silicide fuel loading. The calculation was done by using POKDYN code which available at P2TRR. The calculation was done by reactivity insertion at start up and power rangers. From all cases which were have been done, the results of analysis showed that there is no anomaly and safety margin break at RSG-GAS core with 300 gr silicide fuel loading

Evaluation Of Oxide And Silicide Mixed Fuels Of The RSG-GAS Core

International Nuclear Information System (INIS)

Tukiran; Sembiring, Tagor Malem; Suparlina, Lily

2000-01-01

Fuel exchange of the RSG-GAS reactor core from uranium oxide to uranium silicide in the same loading, density, and enrichment, that is 250 gr, 2.98 gr/cm 3 , and 19.75%, respectively, will be performed in-step wise. In every cycle of exchange with 5/1 mode, it is needed to evaluate the parameter of reactor core operation. The parameters of the reactor operation observed are criticality mass of fuels, reactivity balance, and fuel reactivity that give effect to the reactor operation. The evaluation was done at beginning of cycle of the first and second transition core with compared between experiment and calculation results. The experiments were performed at transition core I and II, BOC, and low power. At transition core I, there are 2 silicide fuels (RI-224 and R1-225) in the core and then, added five silicide fuels (R1-226, R1-252, R1-263, and R1-264) to the core, so that there are seven silicide fuels in the transition core II. The evaluation was done based on the experiment of criticality, control rod calibration, fuel reactivity of the RSG-GAS transition core. For inserting 2 silicide fuels in the transition core I dan 7 fuels in the transition core II, the operation of RSG-GAS core fulfilled the safety margin and the parameter of reactor operation change is not occur drastically in experiment and calculation results. So that, the reactor was operated during 36 days at 15 MW, 540 MWD at the first transition core. The general result showed that the parameter of reactor operation change is small so that the fuel exchange from uranium oxide to uranium silicide in the next step can be done

Neutronic Analysis and Radiological Safety of RSG-GAS Reactor on 300 Grams Uranium Silicide Core

International Nuclear Information System (INIS)

Pande Made Udiyani; Lily Suparlina; Rokhmadi

2007-01-01

As starting of usage silicide U 250 g fuel element in the core of RSG-GAS and will be continued with usage of silicide U 300 g fuel element, hence done beforehand neutronic analyse and radiological safety of RSG-GAS. Calculation done by ORIGEN2.1 code to calculate source term, and also by PC-COSYMA code to calculate radiological safety of radioactive dispersion from RSG-GAS. Calculation of radioactive dispersion done at condition of reactor is postulated be happened an accident of LOCA causing one fuel element to melt. Neutronic analysis indicate that silicide U 250 g full core shall to be operated beforehand during 625 MWD before converted to silicide U 300 g core. During operation of transition core with mixture of silicide U 250 g and 300 g, all parameter fulfill criterion of safety Designed Balance core of silicide U 300 g will be reached at the time of fifth full core. Result of calculation indicate that through mixture core of silicide U 250 and 300 g proposed can form silicide U 300 g balance core of reactor RSG-GAS safely. Calculation of radiology safety by deterministic for silicide U 300 g balance core, and accident postulation which is equal to core of silicide U 250 g yield output in the form of radiation activity (radionuclide concentration in the air and deposition on the ground), radiation dose (collective and individual), radiation effect (short- and long-range), which accepted by society in each perceived sector. Result of calculation indicated that dose accepted by society is not pass permitted boundary for public society if happened accident. (author)

Evaluation of the oxide and silicide fuels reactivity in the RSG-GAS core

International Nuclear Information System (INIS)

S, Tukiran; M S, Tagor; S, Lily; Pinem, S.

2000-01-01

Fuel exchange of The RSG-GAS reactor core from uranium oxide to uranium silicide in the same loading, density, and enrichment, that is, 250 gr, 2.98 gr/cm 3 , and 19.75 % respectively, will be performed in-step wise. In every cycle of exchange with 5/l mode, it is needed to evaluate the parameter of reactor core operation. One of the important operation parameters is fuel reactivity that gives effect to the core reactivity. The experiment was performed at core no. 36, BOC, low power which exist 2 silicide fuels. The evaluation was done based on the RSG-GAS control rod calibration consisting of 40 fuels and 8 control rod.s. From 40 fuels in the core, there are 2 silicide fuels, RI-225/A-9 and RI-224/C-3. For inserting 2 silicide fuels, the reactivity effect to the core must be know. To know this effect , it was performed fuels reactivity experiment, which based on control rod calibration. But in this case the RSG-GAS has no other fresh oxide fuel so that configuration of the RSG-GAS core was rearranged by taking out the both silicide fuels and this configuration is used as reference core. Then silicide fuel RI-224 was inserted to position F-3 replacing the fresh oxide fuel RI-260 so the different reactivity of the fuels is obtained. The experiment result showed that the fuel reactivity change is in amount of 12.85 cent (0.098 % ) The experiment result was compared to the calculation result, using IAFUEL code which amount to 13.49 cent (0.103 %) The result showed that the reactivity change of oxide to silicide fuel is small so that the fuel exchange from uranium oxide to uranium silicide in the first step can be done without any significant change of the operation parameter

Production of Mo-99 using low-enriched uranium silicide

International Nuclear Information System (INIS)

Hutter, J.C.; Srinivasan, B.; Vicek, M.; Vandegrift, G.F.

1994-01-01

Over the last several years, uranium silicide fuels have been under development as low-enriched uranium (LEU) targets for Mo-99. The use of LEU silicide is aimed at replacing the UAl x alloy in the highly-enriched uranium dissolution process. A process to recover Mo-99 from low-enriched uranium silicide is being developed at Argonne National Laboratory. The uranium silicide is dissolved in alkaline hydrogen peroxide. Experiments performed to determine the optimum dissolution procedure are discussed, and the results of dissolving a portion of a high-burnup (>40%) U 3 Si 2 miniplate are presented. Future work related to Mo-99 separation and waste disposal are also discussed

Analysis of impurity effect on Silicide fuels of the RSG-GAS core

International Nuclear Information System (INIS)

Tukiran-Surbakti

2003-01-01

Simulation of impurity effect on silicide fuel of the RSG-GAS core has been done. The aim of this research is to know impurity effect of the U-234 and U-236 isotopes in the silicide fuels on the core criticality. The silicide fuels of 250 g U loading and 19.75 of enrichment is used in this simulation. Cross section constant of fuels and non-structure material of core are generated by WIMSD/4 computer code, meanwhile impurity concentration was arranged from 0.01% to 2%. From the result of analysis can be concluded that the isotopes impurity in the fuels could make trouble in the core and the core can not be operated at critical after a half of its cycle length (350 MW D)

Analysis of the Ford Nuclear Reactor LEU core

Energy Technology Data Exchange (ETDEWEB)

Rathkopf, J A; Drumm, C R; Martin, W R; Lee, J C [Department of Nuclear Engineering, University of Michigan, Ann Arbor, MI (United States)

1983-09-01

This paper has summarized the current status of the effort to analyze the FNR HEU/LEU cores and to compare the calculated results with measurements. In general, calculated predictions of experimental results are quite good, especially for global parameters such as reactivity, as seen in the single HEU/LEU element substitution experiment and the LEU full core critical loading. Shim rod worths are predicted well for two of the rods but too high for a third rod possibly due to inaccurate thermal flux distribution calculation. The calculated thermal flux maps show excellent agreement with experiment throughout the FNR core. In the heavy water tank, however, experimental values for the thermal flux obtained by different methods are inconsistent among themselves as well as with the calculated finding. Work is under.way to use our computational tools to correct the discrepancies between the various measurement techniques and to improve the computational results for flux distribution and the rod worth experiment. Although uncertainties exist in our analysis, as evidenced by the discrepancies mentioned above, we consider our present calculational package to be a useful, reasonably accurate, and efficient system for performing analyses of MTR LEU/HEU core configurations.

RA-3 core with uranium silicide fuel elements

International Nuclear Information System (INIS)

Abbate, Maximo J.; Sbaffoni, Maria M.

2000-01-01

Following on with studies on uranium silicide fuel elements, this paper reports some comparisons between the use of standard ECN [U 3 O 8 ] fuel elements and type P-06 [from U 3 Si 2 ] fuel elements in the RA-3 core.The first results showed that the calculated overall mean burn up is in agreement with that reported for the facility, which gives more confidence to the successive ones. Comparing the mentioned cores, the silicide one presents several advantages such as: -) a mean burn up increase of 18 %; -) an extraction burn up increase of 20 %; -) 37.4 % increase in full power days, for mean burn up. All this is meritorious for this fuel. Moreover, grouped and homogenized libraries were prepared for CITVAP code that will be used for planning experiments and other bidimensional studies. Preliminary calculations were also performed. (author)

Fuel cycle cost comparisons with oxide and silicide fuels

Energy Technology Data Exchange (ETDEWEB)

Matos, J E; Freese, K E [RERTR Program, Argonne National Laboratory (United States)

1983-09-01

This paper addresses fuel cycle cost comparisons for a generic 10 MW reactor with HEU aluminide fuel and with LEU oxide and silicide fuels in several fuel element geometries. The intention of this study is to provide a consistent assessment of various design options from a cost point of view. The status of the development and demonstration of the oxide and silicide fuels are presented in several papers in these proceedings. Routine utilization of these fuels with the uranium densities considered here requires that they are successfully demonstrated and licensed. Thermal-hydraulic safety margins, shutdown margins, mixed cores, and transient analyses are not addressed here, but analyses of these safety issues are in progress for a limited number of the most promising design options. Fuel cycle cost benefits could result if a number of reactors were to utilize fuel elements with the same number or different numbers of the same standard fuel plate. Data is presented to quantify these potential cost benefits. This analysis shows that there are a number of fuel element designs using LEU oxide or silicide fuels that have either the same or lower total fuel cycle costs than the HEU design. Use of these fuels with the uranium densities considered requires that they are successfully demonstrated and licensed. All safety criteria for the reactor with these fuel element designs need to be satisfied as well. With LEU oxide fuel, 31 g U/cm{sup 3} 1 and 0.76 mm--thick fuel meat, elements with 18-22 plates 320-391 g {sup 235}U) result in the same or lower total costs than with the HEU element 23 plates, 280 g {sup 235}U). Higher LEU loadings (more plates per element) are needed for larger excess reactivity requirements. However, there is little cost advantage to using more than 20 of these plates per element. Increasing the fuel meat thickness from 0.76 mm to 1.0 mm with 3.1 g U/cm{sup 3} in the design with 20 plates per element could result in significant cost reductions if the

Safeguarding subcriticality during loading and shuffling operations in the higher density of the RSG-GAS's silicide core

International Nuclear Information System (INIS)

Sembiring, T.M.; Kuntoro, I.

2003-01-01

The core conversion program of the RSG-GAS reactor is to convert the all-oxide to all-silicide core. The silicide equilibrium core with fuel meat density of 3.55 gU cm -3 is an optimal core for RSG-GAS reactor and it can significantly increase the operation cycle length from 25 to 32 full power days. Nevertheless, the subcriticality of the shutdown core and the shutdown margin are lower than of the oxide core. Therefore, the deviation of subcriticality condition in the higher silicide core caused by the fuel loading and shuffling error should be reanalysed. The objective of this work is to analyse the sufficiency of the subcriticality condition of the shutdown core to face the worst condition caused by an error during loading and shuffling operations. The calculations were carried out using the 2-dimensional multigroup neutron diffusion code of Batan-FUEL. In the fuel handling error, the calculated results showed that the subcriticality condition of the shutdown higher density silicide equilibrium core of RSG-GAS can be maintained. Therefore, all fuel management steps are fixed in the present reactor operation manual can be applied in the higher silicide equilibrium core of RSG-GAS reactor. (author)

The Accident Analysis Due to Reactivity Insertion of RSG GAS 3.55 g U/cc Silicide Core

International Nuclear Information System (INIS)

Endiah Puji-Hastuti; Surbakti, Tukiran

2004-01-01

The fuels of RSG-GAS reactor was changed from uranium oxide with 250 g U of loading or 2.96 g U/cc of fuel loading to uranium silicide with the same loading. The silicide fuels can be used in higher density, staying longer in the reactor core and hence having a longer cycle length. The silicide fuel in RSG-GAS core was made up in step-wise by using mixed up core Firstly, it was used silicide fuel with 250 g U of loading and then, silicide fuel with 300 g U of loading (3.55 g U/cc of fuel loading). In every step-wise of fuel loading, it must be analyzed its safety margin. In this occasion, the reactivity accident of RSG-GAS core with 300 g U of silicide fuel loading is analyzed. The calculation was done using EUREKA-2/RR code available at P2TRR. The calculation was done by reactivity insertion at start up and power rangers. The worst case accident is transient due to control rod with drawl failure at start up by means of lowest initial power (0.1 W), either in power range. From all cases which have been done, the results of analysis showed that there is no anomaly and safety margin break at RSG-GAS core with 300 g U silicide fuel loading. (author)

Core conversion study from silicide to molybdenum fuel in the Indonesian 30 MW multipurpose reactor G.A. Siwabessy (RSG-GAS)

International Nuclear Information System (INIS)

Sembiring, T.M.; Kuntoro, I.

2005-01-01

This paper describes the core conversion from silicide to molybdenum core through a series of silicide (2.96 gU cm -3 ) - molybdenum (3.55 gUcm -3 ) mixed transition cores for the Indonesian 30 MW-Multipurpose G.A. Siwabessy (RSGGAS) reactor. The core calculations are carried out using the two-dimensional multigroup neutron diffusion method code of Batan-EQUIL-2D. The calculated results showed that the proposed silicide-molybdenum mixed transition cores, using the same refueling/reshuffling scheme, meet the safety criteria and it can be used in safely converting from an all-silicide core to an all-molybdenum core. (author)

Thermal hydraulic analysis of the JMTR improved LEU-core

Energy Technology Data Exchange (ETDEWEB)

Tabata, Toshio; Nagao, Yoshiharu; Komukai, Bunsaku; Naka, Michihiro; Fujiki, Kazuo [Japan Atomic Energy Research Inst., Oarai, Ibaraki (Japan). Oarai Research Establishment; Takeda, Takashi [Radioactive Waste Management and Nuclear Facility Decommissioning Technology Center, Tokai, Ibaraki (Japan)

2003-01-01

After the investigation of the new core arrangement for the JMTR reactor in order to enhance the fuel burn-up and consequently extend the operation period, the ''improved LEU core'' that utilized 2 additional fuel elements instead of formerly installed reflector elements, was adopted. This report describes the results of the thermal-hydraulic analysis of the improved LEU core as a part of safety analysis for the licensing. The analysis covers steady state, abnormal operational transients and accidents, which were described in the annexes of the licensing documents as design bases events. Calculation conditions for the computer codes were conservatively determined based on the neutronic analysis results and others. The results of the analysis, that revealed the safety criteria were satisfied on the fuel temperature, DNBR and primary coolant temperature, were used in the licensing. The operation license of the JMTR with the improved LEU core was granted in March 2001, and the reactor operation with new core started in November 2001 as 142nd operation cycle. (author)

The conversion of NRU from HEU to LEU fuel

International Nuclear Information System (INIS)

Sears, D.F.; Atfield, M.D.; Kennedy, I.C.

1990-01-01

The program at Chalk River Nuclear Laboratories (CRNL) to develop and test low-enriched uranium fuel (LEU, 3 Si, USiAl, USi Al and U 3 Si 2 (U-3.96 wt% Si; U-3.5 wt% Si-1.5 wt% AL; U-3.2 wt%; Si-3 wt% Al; U-7.3 wt% Si, respectively). Fuel elements were fabricated with uranium loadings suitable for NRU, 3.15 gU/cm 3 , and for NRX, 4.5 gU/cm 3 , and were irradiated under normal fuel-operating conditions. Eight experimental irradiations involving 100 mini-elements and 84 full-length elements (7X12-element rods) were completed to qualify the LEU fuel and the fabrication technology. Post irradiation examinations confirmed that the performance of the LEU fuel, and that of a medium enrichment uranium (MEU, 45% U-235) alloy fuel tested as a back-up, was comparable to the HEU fuel. The uranium silicide dispersion fuel swelling was approximately linear up to burnups exceeding NRU's design terminal burnup (80 at%). NRU was partially converted to LEU fuel when the first 31 prototype fuel rods manufactured with industrial scale production equipment were installed in the reactor. The rods were loaded in NRU at a fuelling rate of about two rods per week over the period 1988 September to December. This partial LEU core (one third of a full NRU core) has allowed the reactor engineers and physicists to evaluate the bulk effects of the LEU conversion on NRU operations. As expected, the irradiation is proceeding without incident

Uranium silicide activities at Babcock and Wilcox

International Nuclear Information System (INIS)

Noel, W.W.; Freim, J.B.

1983-01-01

Babcock and Wilcox, Naval Nuclear Fuel Division (NNFD) in conjunction with Argonne National Laboratory (ANL) is actively involved in the Reduced Enrichment Research Test Reactor (RERTR) Program to produce low enriched fuel elements for research reactors. B and W and ANL have undertaken a joint effort in which NNFD will fabricate two low enriched uranium (LEU), Oak Ridge Reactor (ORR) elements with uranium silicide fuel furnished by ANL. These elements are being fabricated for irradiation testing at Oak Ridge National Laboratory (ORNL). Concurrently with this program, NNFD is developing and implementing the uranium silicide and uranium aluminide fuel fabrication technology. NNFD is fabricating the uranium silicide ORR elements in a two-phase program, Development and Production. To summarize: 1. Full size fuel plates can be made with U 3 SiAl but the fabricator must prevent oxidation of the compact prior to hot roll bonding; 2. Providing the ANL U 3 Si x irradiation results are successful, NNFD plans to provide two ORR elements during February 1983; 3. NNFD is developing and implementing U 3 Si x and UAI x fuel fabrication technology to be operational in 1983; 4. NNFD can supply U 3 O 8 high enriched uranium (HEU) or low enriched uranium (LEU) research reactor elements; 5. NNFD is capable of providing high quality, cost competitive LEU or HEU research reactor elements to meet the needs of the customer

HEU to LEU conversion experience at the UMass-Lowell research reactor

International Nuclear Information System (INIS)

White, John R.; Bobek, Leo M.

2005-01-01

The UMass-Lowell Research Reactor (UMLRR) operated safely with high-enriched uranium (HEU) fuel for over 25 years. Having reached the end of core lifetime and due to proliferation concerns, the reactor was recently converted to low-enriched uranium silicide (LEU) fuel. The actual process for converting the UMLRR from HEU to LEU fuel covered a period of over 15 years. The conversion effort - from the initial conceptual design studies in the late 1980s to the final offsite shipment of the spent HEU fuel in August 2004 - was a unique experience for the faculty and staff of a small university research reactor. This paper gives a historical view of the process and it highlights several key milestones along the road to successful completion of this project. (author)

RA-3 reactor core with uranium silicide fuel elements P-07 type

International Nuclear Information System (INIS)

Abbate, Maximo J.; Sbaffoni, Maria M.

2003-01-01

Following the studies on the utilization of fuel elements (FE) containing uranium silicide, core of the RA-3 was analyzed with several calculation models. At first, the present situation, i.e. the core charged with normal FE (U 3 O 8 ), has been analyzed to validate the simulation methodology comparing with experimental results and to establish reference data to 5 and 10 MW able to be compared with future new situations. Also, CITVAP's nuclear data libraries to be used in irradiation experiment planning were completed. The results were satisfactory and were applied to the study of the core containing P-07 FE [U 3 Si 2 ], in face of a future core change. Comparing with the performance of the U 3 O 8 FE, the silicides ones show the following advantages: - average burnup: 45 % greater; -extraction burnup increase 12 %; and, -the residence time [in full power days] could be a 117 % greater. (author)

Development of new ORIGEN2 data library sets for research reactors with light water cooled oxide and silicide LEU (20 w/o) fuels based on JENDL-3.3 nuclear data

International Nuclear Information System (INIS)

Liem, Peng Hong; Sembiring, Tagor Malem

2013-01-01

Highlights: • We developed new ORIGEN2 data library sets for research reactors based on JENDL-3.3. • The sets cover oxide and silicide LEU fuels with meat density up to 4.74 g U/cm 3 . • Two kinds of data library sets are available: fuel region and non-fuel regions. • We verified the new data library sets with other codes. • We validated the new data library against a non-destructive test. -- Abstract: New sets of ORIGEN2 data library dedicated to research/testing reactors with light water cooled oxide and silicide LEU fuel plates based on JENDL-3.3 nuclear data were developed, verified and validated. The new sets are considered to be an extension of the most recent release of ORIGEN2.2UPJ code, i.e. the ORLIBJ33 library sets. The newly generated ORIGEN2 data library sets cover both oxide and silicide LEU fuels with fuel meat density range from 2.96 to 4.74 g U/cm 3 used in the present and future operation of the Indonesian 30 MWth RSG GAS research reactor. The new sets are expected applicable also for other research/testing reactors which utilize similar fuels or have similar neutron spectral indices. In addition to the traditional ORIGEN2 library sets for fuel depletion analyses in fuel regions, in the new data library sets, new ORIGEN2 library sets for irradiation/activation analyses were also prepared which cover all representative non-fuel regions of RSG GAS such as reflector elements, irradiation facilities, etc. whose neutron spectra are significantly softer than fuel regions. Verification with other codes as well as validation with a non-destructive test result showed promising results where a good agreement was confirmed

Neutronic and thermo-hydraulic design of LEU core for Japan Research Reactor 4

International Nuclear Information System (INIS)

Arigane, Kenji; Watanabe, Shukichi; Tsuruta, Harumichi

1988-04-01

As a part of the Reduced Enrichment Research and Test Reactor (RERTR) program in JAERI, the enrichment reduction for Japan Research Reactor 4 (JRR-4) is in progress. A fuel element using a 19.75 % enriched UAlx-Al dispersion type with a uranium density of 2.2 g/cm 3 was designed as the LEU fuel and the neutronic and thermo-hydraulic performances of the LEU core were compared with those of the current HEU core. The results of the neutronic design are as follows: (1) the excess reactivity of the LEU core becomes about 1 % Δk/k less, (2) the thermal neutron flux in the fuel region decreases about 25 % on the average, (3) the thermal neutron fluxes in the irradiation pipes are almost the same and (4) the core burnup lifetime becomes about 20 % longer. The thermo-hydraulic design also shows that: (1) the fuel plate surface temperature decreases about 10 deg C due to the increase of the number of fuel plates and (2) the temperature margin with respect to the ONB temperature increases. Therefore, it is confirmed that the same utilization performance as the HEU core is attainable with the LEU core. (author)

Comparison of thermohydraulic and nuclear aspects in a standard HEU core and a typical LEU core for the HFR Petten. A case study

International Nuclear Information System (INIS)

Pruimboom, H.; Tas, A.

1985-01-01

Within the framework of the RERTR program various HEU-LEU core calculations have been performed by ANL in a cooperative effort with ECN and JRC Petten. The main purpose of this work has been to gain competence in analysing HEU-LEU core conversion for high power Materials Testing Reactors and to assist in a possible HEU-LEU conversion of the HFR Petten. For reference purposes the present HFR standard core (HEU) in the 'old' vessel geometry was calculated at first. As a next step the new vessel geometry and the increased fuel weights were taken into account. Subsequently various LEU HFR core options have been analysed. Main parameters in the LEU study were the uranium loading in the meat, the fuel type, the thickness of the meat, the number of fuel plates per element and the type of burnable poison applied. Though the study has not yet been completed, one of its striking preliminary results concerns the increased power peaking in the LEU fuel elements as compared with the HEU situation. A preliminary analysis of the thermal characteristics of a typical LEU core as compared with a standard HEU core has been made and is presented in the paper. A short survey of the various HEU and LEU calculations is given. The thermal safety analysis procedure for the HFR, as based on the flow instability criterion, is clarified. Finally, the thermal comparison HEU versus LEU and the resulting conclusions are presented. (author)

Fuel cycle cost study with HEU and LEU fuels

International Nuclear Information System (INIS)

Matos, J.E.; Freese, K.E.

1984-01-01

Fuel cycle costs are compared for a range of 235 U loadings with HEU and LEU fuels using the IAEA generic 10 MW reactor as an example. If LEU silicide fuels are successfully demonstrated and licensed, the results indicate that total fuel cycle costs can be about the same or lower than those with the HEU fuels that are currently used in most research reactors

Calculation of mixed HEU-LEU cores for the HOR research reactor with the scale code system

International Nuclear Information System (INIS)

Leege, P.F.A. de; Gibcus, H.P.M.; Hoogenboom, J.E.; Vries, J.W. de

1997-01-01

The HOR reactor of Interfaculty Reactor Institute (IRI), Delft, The Netherlands, will be converted to use low enriched fuel (LEU) assemblies. As there are still many usable high enriched (HEU) fuel assemblies present, there will be a considerable reactor operation time with mixed cores with both HEU and LEU fuel assemblies. At IRI a comprehensive reactor physics code system and evaluated nuclear data is implemented for detailed core calculations. One of the backbones of the IRI code system is the well-known SCALE code system package. Full core calculations are performed with the diffusion theory code BOLD VENTURE, the nodal code SILWER, and the Monte Carlo code KENO Va. Results are displayed of a strategy from a HEU core to a mixed HEU-LEU core and eventually a LEU core. (author)

Core instrumentation and pre-operational procedures for core conversion HEU to LEU

International Nuclear Information System (INIS)

1984-02-01

This report is intended for the reactor operator, to be used as a manual or checklist for general guidance on pre-startup activities that need to be addressed in preparation for conversion to Low Enriched Fuel (LEU). All nuclear, thermodynamic and safety calculations should have been performed prior to this stage of the core conversion process. During these calculations and certainly before ordering the new LEU fuel elements the reactor operator needs to very carefully consider additional important factors concerning the new fuel: fuel reliability, reliability of fuel fabricator, reprocessing contract or fuel element storage and disposal, economics of the new fuel cycle. At this stage, too, a preoperational experimental programme has to be developed and presented to the regulatory authorities for approval. This experimental programme could lead to additional requirements on: in-core instrumentation, out-of-core instrumentation or additional experimental devices. Detailed instructions on specific tests and measurements are not provided in this report since much information on the subject is available in the open literature

A fuel cycle cost study with HEU and LEU fuels

International Nuclear Information System (INIS)

Matos, J.E.; Freese, K.E.

1985-01-01

Fuel cycle costs are compared for a range of 235 U loadings with HEU and LEU fuels using the IAEA generic 10 MW reactor as an example. If LEU silicide fuels are successfully demonstrated and licensed, the results indicate that total fuel cycle costs can be about the same or lower than those with the HEU fuels that are currently used in most research reactors. (author)

A fuel cycle cost study with HEU and LEU fuels

Energy Technology Data Exchange (ETDEWEB)

Matos, J E; Freese, K E [Argonne National Laboratory, Argonne, IL (United States)

1985-07-01

Fuel cycle costs are compared for a range of {sup 235}U loadings with HEU and LEU fuels using the IAEA generic 10 MW reactor as an example. If LEU silicide fuels are successfully demonstrated and licensed, the results indicate that total fuel cycle costs can be about the same or lower than those with the HEU fuels that are currently used in most research reactors. (author)

Fluxes at experiment facilities in HEU and LEU designs for the FRM-II

International Nuclear Information System (INIS)

Hanan, N. A.

1998-01-01

An Alternative LEU Design for the FRM-II proposed by the RERTR Program at Argonne National Laboratory (ANL) has a compact core consisting of a single fuel element that uses LEU silicide fuel with a uranium density of 4.5 g/cm 3 and has a power level of 32 MW. Both the HEU design by the Technical University of Munich (TUM) and the alternative LEU design by ANL have the same fuel lifetime(50 days) and the same neutron flux performance (8 x 10 14 n/cm 2 -s in the reflector). LEU silicide fuel with 4.5 g/cm 3 has been thoroughly tested and is fully-qualified, licensable, and available now for use in a high flux reactor such as the FRM-II. Several issues that were raised by TUM have been addressed in Refs. 1-3. The conclusions of these analyses are summarized below. This paper addresses four additional issues that have been raised in several forums, including Ref 4: heat generation in the cold neutron source (CNS), the gamma and fast neutron fluxes which are components of the reactor noise in neutron scattering experiments in the experiment hall of the reactor, a fuel cycle length difference, and the reactivity worth of the beam tubes and other experiment facilities. The results show that: (a) for the same thermal neutron flux, the neutron and gamma heating in the CNS is smaller in the LEU design than in the HEU design, and cold neutron fluxes as good or better than those of the HEU design can be obtained with the LEU design; (b) the gamma and fast neutron components of the reactor noise in the experiment hall are about the same in both designs; (c) the fuel cycle length is 50 days for both designs; and (d) the absolute value of the reactivity worth of the beam tubes and other experiment facilities is smaller in the LEU design, allowing its fuel cycle length to be increased to 53 or 54 days. Based on the excellent results for the Alternative LEU Design that were obtained in all analyses, the RERTR Program reiterates its conclusion that there are no major technical

Fuel-cycle cost comparisons with oxide and silicide fuels

International Nuclear Information System (INIS)

Matos, J.E.; Freese, K.E.

1982-01-01

This paper addresses fuel cycle cost comparisons for a generic 10 MW reactor with HEU aluminide fuel and with LEU oxide and silicide fuels in several fuel element geometries. The intention of this study is to provide a consistent assessment of various design options from a cost point of view. Fuel cycle cost benefits could result if a number of reactors were to utilize fuel elements with the same number or different numbers of the same standard fuel plate. Data are presented to quantify these potential cost benefits. This analysis shows that there are a number of fuel element designs using LEU oxide or silicide fuels that have either the same or lower total fuel cycle costs than the HEU design. Use of these fuels with the uranium densities considered requires that they are successfully demonstrated and licensed

Neutronic analysis for core conversion (HEU–LEU of the low power research reactor using the MCNP4C code

Directory of Open Access Journals (Sweden)

Aldawahra Saadou

2015-06-01

Full Text Available Comparative studies for conversion of the fuel from HEU to LEU in the miniature neutron source reactor (MNSR have been performed using the MCNP4C code. The HEU fuel (UAl4-Al, 90% enriched with Al clad and LEU (UO2 12.6% enriched with zircaloy-4 alloy clad cores have been analyzed in this study. The existing HEU core of MNSR was analyzed to validate the neutronic model of reactor, while the LEU core was studied to prove the possibility of fuel conversion of the existing HEU core. The proposed LEU core contained the same number of fuel pins as the HEU core. All other structure materials and dimensions of HEU and LEU cores were the same except the increase in the radius of control rod material from 0.195 to 0.205 cm and keeping the outer diameter of the control rod unchanged in the LEU core. The effective multiplication factor (keff, excess reactivity (ρex, control rod worth (CRW, shutdown margin (SDM, safety reactivity factor (SRF, delayed neutron fraction (βeff and the neutron fluxes in the irradiation tubes for the existing and the potential LEU fuel were investigated. The results showed that the safety parameters and the neutron fluxes in the irradiation tubes of the LEU fuels were in good agreements with the HEU results. Therefore, the LEU fuel was validated to be a suitable choice for fuel conversion of the MNSR in the future.

Mixed core conversion study with HEU and LEU fuels

International Nuclear Information System (INIS)

Matos, J.E.; Freese, K.E.

1984-01-01

The results of a mixed core study are presented for gradual replacement of HEU fuel with LEU fuel using the IAEA generic 10 MW reactor as an example. The key parameters show that the transition can be accomplished safely and economically

Heat-transfer analysis of the existing HEU and proposed LEU cores of Pakistan research reactor

International Nuclear Information System (INIS)

Khan, L.A.; Nabbi, R.

1987-02-01

In connection with conversion of Pakistan Research Reactor (PARR) from the use of Highly Enriched Uranium (HEU) fuel to the use of Low Enriched Uranium (LEU) fuel, steady-state thermal hydraulic analysis of both existing HEU and proposed LEU cores has been carried out. Keeping in mind the possibility of power upgrading, the performance of proposed LEU core, under 10 MW operating conditions, has also been evaluated. Computer code HEATHYD has been used for this purpose. In order to verify the reliability of the code, IAEA benchmark 2 MW reactor was analyzed. The cooling parameters evaluated include: coolant velocity, critical velocity, pressure drop, temperature distribution in the core, heat fluxes at onset of nucleate boiling, flow instability and burnout and corresponding safety margins. From the results of the study it can be concluded that the conversion of the core to LEU fuel will result in higher safety margins, as compared to existing HEU core, mainly because the increased number of fuel plates in the proposed design will reduce the average heat flux significantly. Anyhow upgrading of the reactor power to 10 MW will need the flow rate to be adjusted between 850 to 900 m 3 /hr, to achieve reasonable safety margins, at least, comparable with the existing HEU core. (orig.)

2010 national progress report on R and D on LEU fuel and target technology in Argentina

International Nuclear Information System (INIS)

Balart, S.; Blaumann, H.; Cristini, P.; Gonzalez, A.G.; Gonzalez, R.; Hermida, J.D.; Lopez, M.; Mirandou, M.; Taboada, H.

2010-01-01

Since last RRFM meeting, CNEA has deployed several related tasks. The RA-6 MTR type reactor, converted its core from HEU to a new LEU silicide one is scaling up the power, according to a protocol requested by the national regulatory body, ARN. CNEA is deploying an intense R and D activity to fabricate both dispersed U-Mo (Al-Si matrix and Al cladding) and monolithic (Zry-4 cladding) miniplates to develop possible solutions to VHD dispersed and monolithic fuels technical problems. Some monolithic 58% enrichment U8%Mo and U10%Mo are being delivered to INL-DoE to be irradiated in ATR reactor core. A conscientious study on compound interphase formation in both cases is being carried out. CNEA, a worldwide leader on LEU technology for fission radioisotope production is providing Brazil with these radiopharmaceutical products and Egypt and Australia with the technology through INVAP SE. CNEA is also committed to improve the diffusion of LEU target and radiochemical technology for radioisotope production and target and process optimization. Future plans include: 1) Fabrication of a LEU dispersed U-Mo fuel prototype following the recommendations of the IAEA's Good Practices document, to be irradiated in a high flux reactor in the frame of the ARG/4/092 IAEA's Technical Cooperation project. 2) Development of LEU very high density monolithic and dispersed U-Mo fuel plates with Zry-4 or Al cladding as a part of the RERTR program. 3) Optimization of LEU target and radiochemical techniques for radioisotope production. (author)

Preliminary radiological consequence estimate for a reference LEU core for PARR

International Nuclear Information System (INIS)

Younus, M.; Khan, L.A.; Akhtar, K.M.; Pervez, S.

1988-07-01

Radiological consequence analysis of a reference LEU core for Pakistan Research Reactor (PARR) has been carried out using mathematical models. Three modes of leakage from reactor building have been considered. These are exhaust through the normal ventilation system, through emergency ventilation system and leakage from the building. The whole body and thyroid does have been calculated for the duration of 2 hours and 30 days at the boundaries of exclusion zone at 450m and low population zone at 100m. For the releases at stack height through normal and emergency ventilation systems, does at both the boundaries remain within relevant emergency does limits of 300 rem for thyroid and 25 rem for whole body. However, in case of direct release from the containment building, limiting thyroid does of 300 rem, at 1000m, for 30 days exposure is achieved for a leak rate of 27% per day under Pasquill condition E. The results presented in this report are only preliminary estimates. A more accurate detailed analysis, for various burnups, will be carried using standard computer codes. (orig./A.B)

A mixed core conversion study with HEU and LEU fuels

International Nuclear Information System (INIS)

Matos, J.E.; Freese, K.E.

1985-01-01

The results of a mixed core study are presented for gradual replacement of HEU fuel with LEU fuel using the IAEA generic 10 MW reactor as an example. The key parameters show that the transition can be accomplished safely and economically. (author)

Core-hole effects in the x-ray-absorption spectra of transition-metal silicides

NARCIS (Netherlands)

WEIJS, PJW; CZYZYK, MT; VANACKER, JF; SPEIER, W; GOEDKOOP, JB; VANLEUKEN, H; HENDRIX, HJM; DEGROOT, RA; VANDERLAAN, G; BUSCHOW, KHJ; WIECH, G; FUGGLE, JC

1990-01-01

We report systematic differences between the shape of the Si K x-ray-absorption spectra of transition-metal silicides and broadened partial densities of Si p states. We use a variety of calculations to show that the origin of these discrepancies is the core-hole potential appropriate to the final

Neutron flux measurement in the central channel (XC-1) of TRIGA 14 MW LEU core

International Nuclear Information System (INIS)

BARBOS, D.; BUSUIOC, P.; ROTH, Cs.; PAUNOIU, C.

2008-01-01

The TRIGA 14 MW reactor, operated by Institute for Nuclear Research Pitesti, Romania, is a pool type reactor, and has a rectangular shape which holds fuel bundles and is surrounded with beryllium reflectors. Each fuel bundle is composed of 25 nuclear fuel rods. The TRIGA 14 MW reactor was commissioned 28 years ago with HEU fuel rods. The conversion was gradually achieved, starting in February 1992 and completed in March 2006. The full conversion of the 14 MW TRIGA Research Reactor was completed in May 2006 and each step of the conversion was achieved by removal of HEU fuel, replaced by LEU fuel, accompanied by a large set of theoretical evaluation and physical measurements intended to confirm the performances of gradual conversion. After the core full conversion, a program of measurements and comparisons with previous results of core physics and measurements is underway, allowing data acquisition for normal operation, demonstration of safety and economics of the converted core. Neutron flux spectrum measurements in the XC in the XC-1 water 1 water-filled channel were performed using multi multi-foil activation techniques. The neutron spectra and flux are obtained by unfolding from measured reaction rates using SAND II computer code. The integral neutron flux value for LEU core is greater of 13% than for the standard HEU core. Also thermal neutron flux value for converted LEU core is smaller by 0.38% than for the standard HEU core. These differences appear because the foil activation detectors have been irradiated using a pneumatic rabbit having a diameter of 32 mm, whereas foil irradiations in standard HEU core has been performed with a pneumatic rabbit having a diameter of 14 mm, and therefore the neutron spectra in LEU core is less thermalized and the weight of fast neutron is greater

HEU/LEU-conversion of BER II successfully finished

International Nuclear Information System (INIS)

Haas, K.; Fischer, C.-O.; Krohn, H.

2000-01-01

The BER II (Berliner Experimental Reactor) research reactor is a swimming pool type reactor located in Berlin, Germany. The reactor operates with a thermal power of 10 MW and is primarily used to produce neutrons for neutron scattering experiments. The conversion from HEU- to LEU-fuel elements began in August, 1997. At the last RERTR Meeting 1999 in Budapest, Hungary, Hahn-Meitner-Institut (HMI) presented a 'Status Report' on the conversion of 10 HEU/LEU mixed cores. In February 2000, HMI finished the HEU/LEU-conversion. Hereby, the first pure LEU-standard-core went into operation. Our second LEU-core just ends its operation at the end of July. The third LEU-core will be built up in the beginning of August. The average burn-up rate was improved from 50 - 55% (HEU) to 60 - 65% (LEU). Therefore, only 14 elements/year are now used instead of 28/year. The following report describes our first steps in building pure LEU-cores from mixed HEU/LEU-cores, as well as our initial experience using the pure LEU-cores. (author)

Continuing investigations for technology assessment of 99Mo production from LEU [low enriched uranium] targets

International Nuclear Information System (INIS)

Vandegrift, G.F.; Kwok, J.D.; Marshall, S.L.; Vissers, D.R.; Matos, J.E.

1987-01-01

Currently much of the world's supply of 99m Tc for medical purposes is produced from 99 Mo derived from the fissioning of high enriched uranium (HEU). This paper presents the results of our continuing studies on the effects of substituting low enriched uranium (LEU) for HEU in targets for the production of fission product 99 Mo. Improvements in the electrodeposition of thin films of uranium metal continue to increase the appeal for the substitution of LEU metal for HEU oxide films in cylindrical targets. The process is effective for targets fabricated from stainless steel or zircaloy. Included is a cost estimate for setting up the necessary equipment to electrodeposit uranium metal on cylindrical targets. Further investigations on the effect of LEU substitution on processing of these targets are also reported. Substitution of uranium silicides for the uranium-aluminium alloy or uranium aluminide dispersed fuel used in current target designs will allow the substitution of LEU for HEU in these targets with equivalent 99 Mo-yield per target and no change in target geometries. However, this substitution will require modifications in current processing steps due to 1) the insolubility of uranium silicides in alkaline solutions and 2) the presence of significant quantities of silicate in solution. Results to date suggest that substitution of LEU for HEU can be achieved. (Author)

Progress in the neutronic core conversion (HEU-LEU) analysis of Ghana research reactor-1.

Energy Technology Data Exchange (ETDEWEB)

Anim-Sampong, S.; Maakuu, B. T.; Akaho, E. H. K.; Andam, A.; Liaw, J. J. R.; Matos, J. E.; Nuclear Engineering Division; Ghana Atomic Energy Commission; Kwame Nkrumah Univ. of Science and Technology

2006-01-01

The Ghana Research Reactor-1 (GHARR-1) is a commercial version of the Miniature Neutron Source Reactor (MNSR) and has operated at different power levels since its commissioning in March 1995. As required for all nuclear reactors, neutronic and thermal hydraulic analysis are being performed for the HEU-LEU core conversion studies of the Ghana Research Reactor-1 (GHARR-1) facility, which is a commercial version of the Miniature Neutron Source Reactor (MNSR). Stochastic Monte Carlo particle transport methods and tools (MCNP4c/MCNP5) were used to fine-tune a previously developed 3-D MCNP model of the GHARR-1 facility and perform neutronic analysis of the 90.2% HEU reference and candidate LEU (UO{sub 2}, U{sub 3}Si{sub 2}, U-9Mo) fresh cores with varying enrichments from 12.6%-19.75%. In this paper, the results of the progress made in the Monte Carlo neutronic analysis of the HEU reference and candidate LEU fuels are presented. In particular, a comparative performance assessment of the LEU with respect to neutron flux variations in the fission chamber and experimental irradiation channels are highlighted.

Safety analysis of RSG-GAS Silicide core using one line cooling system

International Nuclear Information System (INIS)

Endiah-Puji-Hastuti

2003-01-01

In the frame of minimizing the operation-cost, operation mode using one line cooling system is being evaluated. Maximum reactor has been determined and to continuing this program, steady state and transient analysis were done. The analysis was done by means of a core thermal hydraulic code, COOLOD-N, and PARET. The codes solves core thermal hydraulic equation at steady state conditions and transient, respectively. By using silicide core data and coast down flow rate as the input, thermal hydraulics parameters such as fuel cladding and fuel meat temperatures as well as safety margin against flow instability were calculated. Imposing the safety criteria to the results of steady state and transient analysis, maximum permissible power for this operation was obtained as much as 17.1 MW

Improvement of JRR-4 core management code system

International Nuclear Information System (INIS)

Izumo, H.; Watanabe, S.; Nagatomi, H.; Hori, N.

2000-01-01

In the modification of JRR-4, the fuel was changed from 93% high enrichment uranium aluminized fuel to 20% low enriched uranium silicide fuel in conformity with the framework of reduced enrichment program on JAERI research reactors. As changing of this, JRR-4 core management code system which estimates excess reactivity of core, fuel burn-up and so on, was improved too. It had been difficult for users to operate the former code system because its input-output form was text-form. But, in the new code system (COMMAS-JRR), users are able to operate the code system without using difficult text-form input. The estimation results of excess reactivity of JRR-4 LEU fuel core were showed very good agreements with the measured value. It is the strong points of this new code system to be operated simply by using the windows form pictures act on a personal workstation equip with the graphical-user-interface (GUI), and to estimate accurately the specific characteristics of the LEU core. (author)

Neutronic design of a LEU [low enriched uranium] core for the Ohio State University research reactor

International Nuclear Information System (INIS)

Seshadri, M.D.; Aybar, H.S.; Aldemir, T.

1987-01-01

The 10 kw HEU fuelled Ohio State University Reactor (OSURR) will be upgraded to operate at 500 kW with standardized 125 g 235 U LEU U 3 Si 2 fuel plates. An earlier scoping study based on two-dimensional diffusion calculations has identified the potential LEU core configurations for the conversion/upgrade of OSURR using the standardized plates in a 16-plate (+ 2 dummy plates) standard and 10-scoping study is improved for a more precise determination of the excess reactivities and safety rod worths for these potential configurations. Comparison of the results obtained by the improved model to experimental results and to the results of full-core Monte Carlo simulations shows excellent agreement. The results also indicate that the conversion/upgrade of OSURR can be realized with three possible LEU core configurations while maintaining a cold, clean shutdown margin of 1.57-1.91 % Δ k/k, depending on the configuration used. (Author)

Status of LEU fuel development and conversion of NRU

International Nuclear Information System (INIS)

Sears, D.F.; Herbert, L.N.; Vaillancourt, K.D.

1989-11-01

The status of the low-enrichment uranium (LEU) fuel development and NRU conversion program at Chalk River Nuclear Laboratories is reviewed. Construction of a new fuel fabrication facility is essentially completed and installation of LEW fuel manufacturing equipment has begun. The irradiation of 31 prototype Al-61 wt% U 3 Si dispersion fuel rods, approximately one third of a full NRU core, is continuing without incident. Recent post-irradiation examination of spent fuel rods revealed that the prototype LEU fuel achieved the design burnup (80 at%) in excellent condition, confirming that the Al-U 3 Si 2 dispersion fuel to complement out Al-U 3 Si capability. Three full-size NRU rods containing Al-U 3 Si 2 dispersion fuel have been fabricated for a qualification irradiation in NRU. Post-irradiation examinations of mini-elements containing Al-U 3 Si 2 fuel revealed that the U 3 Si 2 behaved similarly to U 3 Si 2 fuel revealed that the U 3 Si 2 particles and the aluminum matrix, and fission gas bubbles up to 10 μm in diameter, could be seen in the particles after 60 at% and 80 at% burnup. The mini-elements contained a variety of silicide particle sizes; however, no significant swelling dependence on particle size distribution was observed

Analysis Influence of Mixing Gd2O3 in the Silicide Fuel Element to Core Excess Reactivity of RSG-GAS

International Nuclear Information System (INIS)

Susilo, Jati

2004-01-01

Gadolinium (Gd 2 O 3 ) is a burnable poison material mixed in the pin fuel element of the LWR core used to decrease core excess reactivity. In this research, analysis influence of mixing Gd 2 O 3 in the silicide fuel element to excess reactivity of the RSG-GAS core had been done. Equivalent cell of the equilibrium core developed by L.E.Strawbridge from Westing House Co. burn-up calculation has been done using SRAC-PIJ computer code achieve infinite multiplication factor (k x ). Value of Gd 2 O 3 concentration in the fuel element (pcm) showed by mass ratio of Gd 2 O 3 (gram) to that U 3 Si 2 (gram) times 10 5 , that is 0 pcm ∼ 100 pcm. From the calculation results analysis showed that Gd 2 O 3 concentration added should be considered. because a large number of Gd 2 O 3 will result in not achieving criticality at the Beginning Of Cycle. The maximum concentration of Gd 2 O 3 for RSG-GAS equilibrium fueled silicide 2.96 grU/cc is 80 pcm or 52.02 mgram/fuel plate. Maximum reduction of core excess reactivity due to mixing of Gd 2 O 3 in the RSG-GAS silicide fuels was around 1.502 %Δk/k, and hence not achieving the standard nominal excess reactivity for RSG-GAS core using high density of U 3 Si 2 -Al fuel. (author)

Natural convection cooling of LEU cores for Pakistan research reactor-1

International Nuclear Information System (INIS)

Khan, L.A.; Bokhari, I.H.; Akhtar, K.M.

1991-08-01

The first high power and equilibrium LEU cores of PARR-1 have been analysed to assess the maximum operating power based on natural convection cooling, need for forced cooling to remove the decay heat and to estimate safety margins that commensurate with the predetermined power limit. Computer code NATCON and standard correlations have been used for the analysis. The parameters studied includes coolant velocity, temperature distribution in the core, heat fluxes at onset of nucleate boiling, pulsed boiling and burnup. (author)

Fuel Management Strategies for a Possible Future LEU Core of a TRIGA Mark II Vienna

Energy Technology Data Exchange (ETDEWEB)

Khan, R.; Villa, M.; Steinhauser, G.; Boeck, H. [Vienna University of Technology-Atominstitut (Austria)

2011-07-01

The Vienna University of Technology/Atominstitut (VUT/ATI) operates a TRIGA Mark II research reactor. It is operated with a completely mixed core of three different types of fuel. Due to the US fuel return program, the ATI have to return its High Enriched Uranium (HEU) fuel latest by 2019. As an alternate, the Low Enrich Uranium (LEU) fuel is under consideration. The detailed results of the core conversion study are presented at the RRFM 2011 conference. This paper describes the burn up calculations of the new fuel to predict the future burn up behavior and core life time. It also develops an effective and optimized fuel management strategy for a possible future operation of the TRIGA Mark II with a LEU core. This work is performed by the combination of MCNP5 and diffusion based neutronics code TRIGLAV. (author)

OSIRIS, a MTR adapted and well fitted to LEU utilization qualification and development

International Nuclear Information System (INIS)

Barnier, M.; Beylot, J.P.

1984-01-01

The MTR OSIRIS has been successfully operated for 4 years using the ''Caramel'' low enriched uranium dioxyde fuel for the whole core loading. In the first part we examine the performance and operating experience obtained up to the present time with ''Caramel''. In a second part the paper discusses the results of the calculations for a complete OSIRIS core loaded with 20 % silicide fuel and makes a comparison with UAl 93 % and ''Caramel'' 7 % fuels. (author)

Reactivity And Neutron Flux At Silicide Fuel Element In The Core Of RSG-GAS

International Nuclear Information System (INIS)

Hamzah, Amir

2000-01-01

In order to 4.8 and 5.2 gr U/cm exp 3 loading of U 3 Si 2 --Al fuel plates characterization, he core reactivity change and neutron flux depression had been done. Control rod calibration method was used to reactivity change measurement and neutron flux distribution was measured using foil activation method. Measurement of insertion of A-type of testing fuel element with U-loading above cannot be done due to technical reason, so the measurement using full type silicide fuel element of 2.96 gr U/cm exp 3 loading. The reactivity change measurement result of insertion in A-9 and C-3 is + 2.67 cent. The flux depression at silicide fuel in A-9 is 1.69 times bigger than oxide and in C-3 is 0.68 times lower than oxide

Preliminary radiological consequence estimates for a reference LEU core for PARR

International Nuclear Information System (INIS)

Ali Khan, L.

1990-01-01

Radiological consequence analysis of a reference LEU core for Pakistan Research Reactor (PARR) has been carried out using mathematical models. It was assumed that 20% of the fuel, having an average burn-up of 50% achieved by continuously operating the reactor for 300 days at 10 MW, fails. It was further assumed that 100% of the noble gases and a fraction of iodine are released. Three modes of leakage from reactor building have been considered. These are exhaust through the normal ventilation system, through emergency ventilation system and leakage from the building. The whole body and thyroid doses have been calculated for 2 hours and 30 days at the boundaries of the exclusion zone at 450m and the low population zone at 1000m. For the releases at stack height through normal and emergency ventilation system, doses at both the boundaries remain within emergency dose limits of 300 rem for thyroid and 25 rem for the whole body. However, in the case of direct release from the containment building, the limiting thyroid dose of 300 rem, at 1000m, for 30 days exposure is achieved for a leak rate of 27% per day under Pasquill condition E. The results presented in this report are only preliminary estimates. A more accurate detailed analysis for various burnups will be carried out using standard computer codes

Continuing investigations for technology assessment of 99Mo production from LEU [low enriched Uranium] targets

International Nuclear Information System (INIS)

Vandergrift, G.F.; Kwok, J.D.; Marshall, S.L.; Vissers, D.R.; Matos, J.E.

1987-01-01

Currently much of the world's supply of /sup 99m/Tc for medical purposes is produced from 99 Mo derived from the fissioning of high enriched uranium (HEU). The need for /sup 99m/Tc is continuing to grow, especially in developing countries, where needs and national priorities call for internal production of 99 Mo. This paper presents the results of our continuing studies on the effects of substituting low enriched Uranium (LEU) for HEU in targets for the production of fission product 99 Mo. Improvements in the electrodeposition of thin films of uranium metal are reported. These improvements continue to increase the appeal for the substitution of LEU metal for HEU oxide films in cylindrical targets. The process is effective for targets fabricated from stainless steel or hastaloy. A cost estimate for setting up the necessary equipment to electrodeposit uranium metal on cylindrical targets is reported. Further investigations on the effect of LEU substitution on processing of these targets are also reported. Substitution of uranium silicides for the uranium-aluminum alloy or uranium aluminide dispersed fuel used in other current target designs will allow the substitution of LEU for HEU in these targets with equivalent 99 Mo-yield per target and no change in target geometries. However, this substitution will require modifications in current processing steps due to (1) the insolubility of uranium silicides in alkaline solutions and (2) the presence of significant quantities of silicate in solution. Results to date suggest that both concerns can be handled and that substitution of LEU for HEU can be achieved

Status of HEU-LEU conversion of FRJ-2

International Nuclear Information System (INIS)

Damm, G.; Nabbi, R.

2002-01-01

The operator of the German FRJ-2 research reactor, 'Research Center Juelich', has participated from the beginning in the RERTR programme and made comprehensive contributions to the test and use of LEU fuel for HEU-LEU-conversion measures. The originally planned time scale for the conversion of FRJ-2 was significantly delayed because of a change of the manufacturer of the LEU fuel elements and a 4 years shutdown of the reactor for refurbishment purposes. In the meantime the new LEU fuel elements are qualified and tested in the reactor. In the moment calculations for the safety report are made and it is planned to apply for the license of FRJ-2 operation with LEU fuel at the beginning of 2003. In order to get most reliable results a sophisticated computational method based on a MCNP model coupled with the depletion code BURN was developed for reactor physical calculations, core conversion studies and fuel element performance analysis and applied to the mixed and LEU core. The licensing schedule and results of latest calculations for the conversion study will be presented. The simulations shows that the thermal flux in the LEU core is about 19% resulting in a lower burnup rate. But in the reflector area around the core and in the center of the cold n source the neutron flux reduction remains limited to 6%. Due to a harder neutron spectrum in the LEU core the kinetic and safety related parameters are slightly reduced. Using the ORIGEN code it could be shown that the increase of the total fission products inventory amounts to about 6% compared to a HEU core. As a consequence of the high amount of U-238, the amount of U-235 in the LEU core has to be about 27% higher than in the HEU core but the U-235 burnup is approx. 5% lower due to the contribution of fissile plutonium. (author)

Prompt Neutron Decay Constant Determination Of Silicide Transition Core Using Noise Method

International Nuclear Information System (INIS)

Jujuratisbela, Uju; Yulianto, Yusi Eko; Cahyana

2001-01-01

Chairman of BATAN had decided to replace the Oxide fuel element type of RSG-GAS into silicide element type step by step. The replacement will create core transitions. Kinetic characteristic of the transition cores have to be monitored in order to know the deviation of core behavior. For that reason, the kinetic parameters have to be measured. Prompt neutron decay constant (alpha) is one of the kinetic parameters that has to be monitored continuously in the transition cores. In order not to disturb the normal operation of reactor, alpha parameter should be measured by using noise analysis method. The voltage of neutron flux at power of 15 MW is connected to preamplifier and filter then to the Dynamic Signal Analyzer Version-2 and then the auto power spectral density (APSD) was determined by using Fast Fourier transform. From the APSD curve of each channel of JKT03, the cut off frequency of each channel can be determined by using linear regression technique such that the prompt neutron decay constant can be estimated

Performance of Estimation of distribution algorithm for initial core loading optimization of AHWR-LEU

International Nuclear Information System (INIS)

Thakur, Amit; Singh, Baltej; Gupta, Anurag; Duggal, Vibhuti; Bhatt, Kislay; Krishnani, P.D.

2016-01-01

Highlights: • EDA has been applied to optimize initial core of AHWR-LEU. • Suitable value of weighing factor ‘α’ and population size in EDA was estimated. • The effect of varying initial distribution function on optimized solution was studied. • For comparison, Genetic algorithm was also applied. - Abstract: Population based evolutionary algorithms now form an integral part of fuel management in nuclear reactors and are frequently being used for fuel loading pattern optimization (LPO) problems. In this paper we have applied Estimation of distribution algorithm (EDA) to optimize initial core loading pattern (LP) of AHWR-LEU. In EDA, new solutions are generated by sampling the probability distribution model estimated from the selected best candidate solutions. The weighing factor ‘α’ decides the fraction of current best solution for updating the probability distribution function after each generation. A wider use of EDA warrants a comprehensive study on parameters like population size, weighing factor ‘α’ and initial probability distribution function. In the present study, we have done an extensive analysis on these parameters (population size, weighing factor ‘α’ and initial probability distribution function) in EDA. It is observed that choosing a very small value of ‘α’ may limit the search of optimized solutions in the near vicinity of initial probability distribution function and better loading patterns which are away from initial distribution function may not be considered with due weightage. It is also observed that increasing the population size improves the optimized loading pattern, however the algorithm still fails if the initial distribution function is not close to the expected optimized solution. We have tried to find out the suitable values for ‘α’ and population size to be considered for AHWR-LEU initial core loading pattern optimization problem. For sake of comparison and completeness, we have also addressed the

Study on Al-alloy or silicide LEU for DR3 in Denmark

Energy Technology Data Exchange (ETDEWEB)

Haack, Karsten [Riso National Laboratory, DK 4000 Roskilde (Germany)

1985-07-01

The 10 MW D{sub 2}0-moderated and -cooled research reactor DR3 has at present HEU fuel available for continued operation till early 19. This report presents the status of a feasibility study prepared for selection of the best suited candidate LEU fuel type for DR3 at a potential conversion in 1988. At the moment two alternatives are evaluated: UAl-alloy with modified geometry and U{sub 3}Si{sub 2} with unchanged geometry. A decision on the type selected for further investigation is expected late 1984. The investigation should comprise development, in- and out-of-pile--testing and licensing activities on the potential LEU option. (author)

Determination of Dancoff correction thermal utilization and thermal disadvantage factors of HEU and LEU cores of an MNSR

International Nuclear Information System (INIS)

Ofori, Y. T.

2013-07-01

Ghana Research Reactor-1 (GHARR-1), an MNSR (Miniature Neutron Source Reactor) is to be converted from HEU (Highly Enriched Uranium) to LEU (Low Enriched Uranium) fuel, along with all current MNSRs in various other countries. The purpose of the conversion is to minimize the use of HEU for non-proliferation of high-grade nuclear fuel. In this research work, a comparative study has been performed for the determination of the Dancoff, thermal utilization and thermal disadvantage factors of highly enriched uranium (HEU) and potential low enriched uranium (LEU) cores of GHARR-1. A one group transport theory and collision probability based methodologies was used to develop mathematical formulations for thermal utilization factor and thermal disadvantage factor assuming isotropic scattering. This methodology was implemented in a FORTRAN 95 based computer program THERMCALC, which uses Bessell and BesselK as subroutines developed to calculate the modified Bessel functions I n and K n respectively using the polynomial approximation method. Furthermore, a Dancoff correction factor of 0.1519 thermal utilization factor of 0.9767 and a thermal disadvantage factor of 1.894 were obtained for the 90.2% highly enriched Uranium core of GHARR-1. The results compare favorably with literature. Thus THERMCALC can be used as a reliable tool for the calculation of Dancoff, thermal utilization and disadvantage factors of MNSR cores. Other potential LEU cores; UO 2 (with different fuel meat densities and enrichments) and U 3 Si 2 have also been analysed. UO 2 with 12.6% of Uranium-235 was chosen as the most potential LEU core for the GHARR-1. (au)

Followup calculations for the UVAR LEU conversion

International Nuclear Information System (INIS)

Rydin, R.; Hosticka, B.; Burns, T; Hubbard, T.; Mulder, R

2004-01-01

The UVAR reactor was successfully converted to LEU fuel in April 1994. Void coefficient measurements were made on the 4- by-4 fully-graphite-reflected LEU-1 core configuration, and an isothermal temperature coefficient measurement was made on the operational 4-by-5 partially-graphite-reflected LEU-2 core configuration. Both of these experiments have now been modeled in their critical configurations using the 3DBUM code. The LEU cores were also modeled using the Monte Carlo code MCNP in order to obtain a neutron/gamma source for BNCT filter design calculations. Advanced BNCT filters have been evaluated using both MCNP and the discrete ordinates code DORT. The results indicate that the UVAR would be an ideal source for the BNCT treatment of brain tumors. (author)

Followup calculations for the UVAR LEU conversion

International Nuclear Information System (INIS)

Rydin, R.A.; Hosticka, B.; Burns, T.

1995-01-01

The UVAR reactor was successfully converted to LEU fuel in April 1994. Void coefficient measurements were made on the 4-by-4 fully-graphite-reflected LEU-1 core configuration, and an isothermal temperature coefficient measurement was made on the operational 4-by-5 partially-graphite-reflected LEU-2 core configuration. Both of these experiments have now been modeled in their critical configurations using the 3DBUM code. The LEU cores were also modeled using the Monte Carlo code MCNP in order to obtain a neutron/gamma source for BNCT filter design calculations. Advanced BNCT filters have been evaluated using both MCNP and the discrete ordinates code DORT. The results indicate that the UVAR would be an ideal source for the BNCT treatment of brain tumors

Fuel element burnup determination in HEU-LEU mixed TRIGA research reactor core

International Nuclear Information System (INIS)

Zagar, Tomaz; Ravnik, Matjaz

2000-01-01

This paper presents the results of a burnup calculations and burnup measurements for TRIGA FLIP HEU fuel elements and standard TRIGA LEU fuel elements used simultaneously in small TRIGA Mark II research reactor in Ljubljana, Slovenija. The fuel element burnup for approximately 15 years of operation was calculated with two different in house computer codes TRIGAP and TRIGLAV (both codes are available at OECD NEA Data Bank). The calculation is performed in one-dimensional radial geometry in TRIGAP and in two-dimensional (r,φ) geometry in TRIGLAV. Inter-comparison of results shows important influence of in-core water gaps, irradiation channels and mixed rings on burnup calculation accuracy. Burnup of 5 HEU and 27 LEU fuel elements was also measured with reactivity method. Measured and calculated burnup values are inter-compared for these elements (author)

Core management and reactor physics aspects of the conversion of the NRU reactor to LEU

International Nuclear Information System (INIS)

Atfield, M.D.

1985-01-01

Results of work done to assess the effects of converting the NRU reactor to LEU are presented. The effects are small, and the operational rules and safety analysis, appropriate to the HEU core, will still apply. (author)

Safety analysis of JMTR LEU fuel core, (3)

International Nuclear Information System (INIS)

Tsuchida, Noboru; Shiraishi, Tadao; Takahashi, Yutaka; Inada, Seiji; Saito, Minoru; Futamura, Yoshiaki; Kitano, Kyoshiro.

1992-10-01

Dose analysis in the safety evaluation and the site evaluation were performed for the JMTR core conversion from MEU fuel to LEU fuel. In the safety evaluation, the effective dose equivalents for the public surrounding the site were estimated in fuel handling accident and flow blockage to coolant channel which were selected as the design basis accidents with release of radioactive fission products to the environment. In the site evaluation, the flow blockage to coolant channel was selected as siting basis events, since this accident had the possibility of spreading radioactive release. Maximum exposure doses for the public were estimated assuming large amounts of fission products to release. It was confirmed that risk of radiation exposure of the public is negligible and the siting is appropriate. (author)

Neutronic analysis of the conversion of HEU to LEU fuel for a 5-MW MTR core

International Nuclear Information System (INIS)

Pazirandeh, A.; Bartsch, G.

1987-01-01

In recent years, due to cessation of highly enriched uranium (HEU) fuel supply, practical steps have been taken to substitute HEU fuel in almost all research reactors by medium-enriched uranium or low-enriched uranium (LEU) fuels. In this study, a neutronic calculation of a 5-MW research reactor core fueled with HEU (93% 235 U) is presented. In order to assess the performance of the core with the LEU ( 235 U loadings were examined. The core consists of 22 standard fuel elements (SFEs) and 6 control fuel elements (CFEs). Each fuel elements has 18 curved plates of which two end plates are dummies. Initial 235 U content is 195 g 235 U/SFE and 9.7 g 235 U/CFE or /PFE. In all calculations the permitted changes to the fuel elements are (a) 18 active plates per SFE, (b) fuel plates assumed to be flat, and (c) 8 or 9 active plates per CFE

Thermal-hydraulic analysis of research reactor core with different LEU fuel types using RELAP5

Energy Technology Data Exchange (ETDEWEB)

El-Sahlamy, Neama M. [Nuclear and Radiological Regulatory Authority, Cairo (Egypt)

2017-11-15

In the current work, comparisons between the core performances when using different LEU fuels are done. The fuels tested are UA1{sub X}-A1, U{sub 3}O{sub 8}-Al, and U{sub 3}Si{sub 2}-Al fuels with 19.7 % enrichment. Calculations are done using RELAP5 code to evaluate the thermal-hydraulic performance of the IAEA benchmark 10 MW reactor. First, a reassessment of the slow reactivity insertion transient with UA1{sub X}-A1 LEU fuel to compare the results with those reported in the IAEA TECDOC [1]. Then, comparisons between the thermal-hydraulic core performances when using the three LEU fuels are done. The assessment is performed at initial power of 1.0 W. The reactor power is calculated using the RELAP5 point kinetic model. The reactivity feedback, from changes in water density and fuel temperature, is considered for all cases. From the results it is noticed that U{sub 3}Si{sub 2}-Al fuel gives the best fuel performance since it has the minimum value of peak fuel temperature and the minimum peak clad surface temperature, as operating parameters. Also, it gives the maximum value of the Critical Heat Flux Ratio and the lowest tendency to flow instability occurrence.

The fabrication and performance of Canadian silicide dispersion fuel for test reactors

International Nuclear Information System (INIS)

Sears, D.F.; Wood, J.C.; Berthiaume, L.C.; Herbert, L.N.; Schaefer, J.D.

1985-01-01

Fuel fabrication effort is now concentrated on the commissioning of large-scale process equipment, defining product specifications, developing a quality assurance plan, and setting up a mini-computer material accountancy system. In the irradiation testing program, full-size NRU assemblies containing 20% enriched silicide dispersion fuel have been Irradiated successfully to burnups in the range 65-80 atomic percent. Irradiations have also been conducted on mini-elements having 1.2 mm diameter holes In their mid-sections, some drilled before irradiation and others after irradiation to 22-83 atomic percent burnup. Uranium was lost to the coolant in direct proportion to the surface area of exposed core material. Pre-irradiation in the intact condition appeared to reduce in-reactor corrosion. Fuel cores developed for the NRU reactor are dimensionally very stable, swelling by only 6-8% at the very high burnup of 93 atomic percent. Two important factors contributing to this good performance are cylindrical clad restraint and coarse silicide particles. Thermal ramping tests were conducted on irradiated silicide aspersion fuels. Small segments of fuel cores released 85 Kr starting at about 520 deg. C and peaking at about 680 deg C. After a holding period of 1 hour at 720 deg. C a secondary 85 Kr peak occurred during cooling (at about 330 deg. C) probably due to thermal contraction cracking. Whole mini-elements irradiated to 93 atomic percent burnup were also ramped thermally, with encouraging results. After about 0.25 h at 530 deg. C the aluminum cladding developed very localized small blisters, some with penetrating pin-hole cracks preventing gross pillowing or ballooning. (author)

The fabrication and performance of Canadian silicide dispersion fuel for test reactors

Energy Technology Data Exchange (ETDEWEB)

Sears, D F; Wood, J C; Berthiaume, L C; Herbert, L N; Schaefer, J D

1985-07-01

Fuel fabrication effort is now concentrated on the commissioning of large-scale process equipment, defining product specifications, developing a quality assurance plan, and setting up a mini-computer material accountancy system. In the irradiation testing program, full-size NRU assemblies containing 20% enriched silicide dispersion fuel have been Irradiated successfully to burnups in the range 65-80 atomic percent. Irradiations have also been conducted on mini-elements having 1.2 mm diameter holes In their mid-sections, some drilled before irradiation and others after irradiation to 22-83 atomic percent burnup. Uranium was lost to the coolant in direct proportion to the surface area of exposed core material. Pre-irradiation in the intact condition appeared to reduce in-reactor corrosion. Fuel cores developed for the NRU reactor are dimensionally very stable, swelling by only 6-8% at the very high burnup of 93 atomic percent. Two important factors contributing to this good performance are cylindrical clad restraint and coarse silicide particles. Thermal ramping tests were conducted on irradiated silicide aspersion fuels. Small segments of fuel cores released {sup 85}Kr starting at about 520 deg. C and peaking at about 680 deg C. After a holding period of 1 hour at 720 deg. C a secondary {sup 85}Kr peak occurred during cooling (at about 330 deg. C) probably due to thermal contraction cracking. Whole mini-elements irradiated to 93 atomic percent burnup were also ramped thermally, with encouraging results. After about 0.25 h at 530 deg. C the aluminum cladding developed very localized small blisters, some with penetrating pin-hole cracks preventing gross pillowing or ballooning. (author)

Core thermohydraulic design with LEU fuels for upgraded research reactor, JRR-3

Energy Technology Data Exchange (ETDEWEB)

Sudo, Y; Ando, H; Ikawa, H; Ohnishi, N [Department of Research Reactor Operation, Japan Atomic Energy Research Institute (JAERI), 319-11 Tokai-Mura, Ibaraki-Ken (Japan)

1985-07-01

This paper presents the outline of core thermohydraulic design and analysis of the research reactor, JRR-3, which is to be upgraded to a 20 MWt pool-type, light water-cooled reactor with 20% LEU plate-type fuels. The major feature of core thermohydraulics of the upgraded JRR-3 is that core flow is a downflow at the condition of normal operation, with which fuel plates are exposed to a severer condition than with an upflow in case of operational transients and accidents. The core thermo-hydraulic design was, therefore, done for the condition of normal operation so that fuel plates may have enough safety margin both against the onset of nucleate boiling not to allow the nucleate boiling anywhere in the core and against the initiation of DNB, and the safety margin for these were evaluated. The core velocity thus designed is at the optimum condition where fuel plates have the maximum margin against the onset of nucleate boiling. The core thermohydraulic characteristics were also clarified for the natural circulation cooling mode. (author)

Preliminary investigations on the use of uranium silicide targets for fission Mo-99 production

Energy Technology Data Exchange (ETDEWEB)

Cols, H.; Cristini, P.; Marques, R.

1997-08-01

The National Atomic Energy Commission (CNEA) of Argentine Republic owns and operates an installation for production of molybdenum-99 from fission products since 1985, and, since 1991, covers the whole national demand of this nuclide, carrying out a program of weekly productions, achieving an average activity of 13 terabecquerel per week. At present they are finishing an enlargement of the production plant that will allow an increase in the volume of production to about one hundred of terabecquerel. Irradiation targets are uranium/aluminium alloy with 90% enriched uranium with aluminium cladding. In view of international trends held at present for replacing high enrichment uranium (HEU) for enrichment values lower than 20 % (LEU), since 1990 the authors are in contact with the RERTR program, beginning with tests to adapt their separation process to new irradiation target conditions. Uranium silicide (U{sub 3}Si{sub 2}) was chosen as the testing material, because it has an uranium mass per volume unit, so that it allows to reduce enrichment to a value of 20%. CNEA has the technology for manufacturing miniplates of uranium silicide for their purposes. In this way, equivalent amounts of Molybdenum-99 could be obtained with no substantial changes in target parameters and irradiation conditions established for the current process with Al/U alloy. This paper shows results achieved on the use of this new target.

LEU fuel cycle analyses for the Belgian BR2 Research Reactor

International Nuclear Information System (INIS)

Deen, J.R.; Snelgrove, J.L.

1988-01-01

Equilibrium fuel cycle characteristics were calculated for reference HEU and two proposed LEU fuel cycles using an 11-group diffusion-theory neutron flux solution in hexagonal-Z geometry. The diffusion theory model was benchmarked with a detailed Monte Carlo core model. The two proposed LEU fuel designs increased the 235 U loading 20% and the fuel meat volume 51%. The first LEU design used 10 B as a burnable absorber. Either proposed LEU fuel element would provide equilibrium fuel cycle characteristics similar to those of the HEU fuel cycle. Irradiation rates of Co control followers and Ir disks in the center of the core were reduced 6 ± 1% in the LEU equilibrium core compared to reference HEU core. 11 refs., 4 figs., 5 tabs

Core physics analysis in support of the FNR HEU-LEU demonstration experiment

Energy Technology Data Exchange (ETDEWEB)

Losey, David C; Brown, Forrest B; Martin, William R; Lee, John C [Department of Nuclear Engineering, University of Michigan (United States)

1983-08-01

A core neutronics analysis has been undertaken to assess the impact of low-enrichment fuel on the performance and utilization of the FNR As part of this analytic effort a computer code system has been assembled which will be of general use in analyzing research reactors with MTR-type fuel. The code system has been extensively tested and verified in calculations for the present high enrichment core. The analysis presented here compares the high-and-low enrichment fuels in batch and equilibrium core configurations which model the actual FNR operating conditions. The two fuels are compared for cycle length, fuel burnup, and flux and power distributions, as well as for the reactivity effects which are important in assessing the impact of LEU fuel on reactor shutdown margin. (author)

Core physics analysis in support of the FNR HEU-LEU demonstration experiment

International Nuclear Information System (INIS)

Losey, David C.; Brown, Forrest B.; Martin, William R.; Lee, John C.

1983-01-01

A core neutronics analysis has been undertaken to assess the impact of low-enrichment fuel on the performance and utilization of the FNR As part of this analytic effort a computer code system has been assembled which will be of general use in analyzing research reactors with MTR-type fuel. The code system has been extensively tested and verified in calculations for the present high enrichment core. The analysis presented here compares the high-and-low enrichment fuels in batch and equilibrium core configurations which model the actual FNR operating conditions. The two fuels are compared for cycle length, fuel burnup, and flux and power distributions, as well as for the reactivity effects which are important in assessing the impact of LEU fuel on reactor shutdown margin. (author)

Preliminary Assessment of the Impact on Reactor Vessel dpa Rates Due to Installation of a Proposed Low Enriched Uranium (LEU) Core in the High Flux Isotope Reactor (HFIR)

Energy Technology Data Exchange (ETDEWEB)

Daily, Charles R. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

2015-10-01

An assessment of the impact on the High Flux Isotope Reactor (HFIR) reactor vessel (RV) displacements-per-atom (dpa) rates due to operations with the proposed low enriched uranium (LEU) core described by Ilas and Primm has been performed and is presented herein. The analyses documented herein support the conclusion that conversion of HFIR to low-enriched uranium (LEU) core operations using the LEU core design of Ilas and Primm will have no negative impact on HFIR RV dpa rates. Since its inception, HFIR has been operated with highly enriched uranium (HEU) cores. As part of an effort sponsored by the National Nuclear Security Administration (NNSA), conversion to LEU cores is being considered for future HFIR operations. The HFIR LEU configurations analyzed are consistent with the LEU core models used by Ilas and Primm and the HEU balance-of-plant models used by Risner and Blakeman in the latest analyses performed to support the HFIR materials surveillance program. The Risner and Blakeman analyses, as well as the studies documented herein, are the first to apply the hybrid transport methods available in the Automated Variance reduction Generator (ADVANTG) code to HFIR RV dpa rate calculations. These calculations have been performed on the Oak Ridge National Laboratory (ORNL) Institutional Cluster (OIC) with version 1.60 of the Monte Carlo N-Particle 5 (MCNP5) computer code.

Fabrication and irradiation testing of LEU [low enriched uranium] fuels at CRNL status as of 1987 September

International Nuclear Information System (INIS)

Sears, D.F.; Berthiaume, L.C.; Herbert, L.N.

1987-01-01

The current status of Chalk River Nuclear Laboratories' (CRNL) program to develop and test low-enriched uranium (LEU), proliferation-resistant fuels for use in research reactors is reviewed. CRNL's fuel manufacturing process has been qualified by the successful demonstration irradiation of 7 full-size rods in the NRU reactor. Now industrial-scale production equipment has been commissioned, and a fuel-fabrication campaign for 30 NRU rods and a MAPLE-X core is underway. Excess capacity could be used for commercial fuel fabrication. In the irradiation testing program, mini-elements with deliberately included core surface defects performed well in-reactor, swelling by only 7 to 8 vol% at 93 atomic percent burnup of the original U-235. The additional restraint provided by the aluminium cladding which flowed into the defects during extrusion contributed to this good performance. Mini-elements containing a variety of particle size distributions were also successfully irradiated to 93 at% burnup in NRU, as part of a study to establish the optimum particle size distribution. Swelling was found to be proportional to the percentage of fines (<44μm particles) contained in the cores. The mini-elements containing the composition normally used at CRNL had swollen by 5.8 vol%, and mini-elements with a much higher percentage of fines had swollen by 6.8 vol%, at 93 at% burnup. Also, a program to develop LEU targets for Mo-99 production, via the technology developed to fabricate dispersed silicide fuel, has started, and preliminary scoping studies are underway. (Author)

A neutronic feasibility study for LEU conversion of the High Flux Beam Reactor (HFBR)

International Nuclear Information System (INIS)

Pond, R.B.; Hanan, N.A.; Matos, J.E.

1997-01-01

A neutronic feasibility study for converting the High Flux Beam Reactor at Brookhaven National Laboratory from HEU to LEU fuel was performed at Argonne National Laboratory. The purpose of this study is to determine what LEU fuel density would be needed to provide fuel lifetime and neutron flux performance similar to the current HEU fuel. The results indicate that it is not possible to convert the HFBR to LEU fuel with the current reactor core configuration. To use LEU fuel, either the core needs to be reconfigured to increase the neutron thermalization or a new LEU reactor design needs to be considered. This paper presents results of reactor calculations for a reference 28-assembly HEU-fuel core configuration and for an alternative 18-assembly LEU-fuel core configuration with increased neutron thermalization. Neutronic studies show that similar in-core and ex-core neutron fluxes, and fuel cycle length can be achieved using high-density LEU fuel with about 6.1 gU/cm 3 in an altered reactor core configuration. However, hydraulic and safety analyses of the altered HFBR core configuration needs to be performed in order to establish the feasibility of this concept. (author)

Near surface silicide formation after off-normal Fe-implantation of Si(001) surfaces

Energy Technology Data Exchange (ETDEWEB)

Khanbabaee, B., E-mail: khanbabaee@physik.uni-siegen.de; Pietsch, U. [Solid State Physics, University of Siegen, D-57068 Siegen (Germany); Lützenkirchen-Hecht, D. [Fachbereich C - Physik, Bergische Universität Wuppertal, D-42097 Wuppertal (Germany); Hübner, R.; Grenzer, J.; Facsko, S. [Helmholtz-Zentrum Dresden-Rossendorf, 01314 Dresden (Germany)

2014-07-14

We report on formation of non-crystalline Fe-silicides of various stoichiometries below the amorphized surface of crystalline Si(001) after irradiation with 5 keV Fe{sup +} ions under off-normal incidence. We examined samples prepared with ion fluences of 0.1 × 10{sup 17} and 5 × 10{sup 17} ions cm{sup −2} exhibiting a flat and patterned surface morphology, respectively. Whereas the iron silicides are found across the whole surface of the flat sample, they are concentrated at the top of ridges at the rippled surface. A depth resolved analysis of the chemical states of Si and Fe atoms in the near surface region was performed by combining X-ray photoelectron spectroscopy and X-ray absorption spectroscopy (XAS) using synchrotron radiation. The chemical shift and the line shape of the Si 2p core levels and valence bands were measured and associated with the formation of silicide bonds of different stoichiometric composition changing from an Fe-rich silicides (Fe{sub 3}Si) close to the surface into a Si-rich silicide (FeSi{sub 2}) towards the inner interface to the Si(001) substrate. This finding is supported by XAS analysis at the Fe K-edge which shows changes of the chemical environment and the near order atomic coordination of the Fe atoms in the region close to surface. Because a similar Fe depth profile has been found for samples co-sputtered with Fe during Kr{sup +} ion irradiation, our results suggest the importance of chemically bonded Fe in the surface region for the process of ripple formation.

Development of LEU targets for 99Mo production and their chemical processing status 1989

International Nuclear Information System (INIS)

Vandegrift, G.F.; Kwok, J.D.; Chamberlain, D.B.; Hoh, J.C.; Streets, E.W.; Vogler, S.; Thresh, H.R.; Domagala, R.F.; Wiencek, T.C.; Matos, J.E.

1991-01-01

Most of the world's supply of Tc-99m for medical purposes is currently produced from Mo-99 derived from the fissioning of high enriched uranium (HEU). Substitution of low enriched uranium (LEU) silicide fuel for the HEU alloy and aluminide fuels used in current target designs will allow equivalent Mo-99 yields with no change in target geometries. Substitution of uranium metal will also allow the substitution of LEU for HEU. Efforts performed in 1989 focused on (1) fabrication of a uranium metal target by Hot Isostatic Pressing uranium metal foil to zirconium, (2) experimental investigation of the dissolution step for U 3 Si 2 targets, allowing us to present a conceptual design for the dissolution process and equipment, and (3) investigation of the procedures used to reclaim irradiated uranium from Mo-production targets, allowing us to further analyze the waste and by-product problems associated with the substitution of LEU for HEU. (orig.)

Analysis of the critical and first full power operating cores for PARR using leu oxide fuel

International Nuclear Information System (INIS)

Khan, L.A.; Qazi, M.K.; Bokhari, I.H.; Fazal, R.

1989-10-01

This paper explains the analysis for determining the first full power operating core for PARR using LEU oxide fuel. The core configuration selected for this first full power operation contains about 6.13 kg of U-235 distributed in 19 standard and five control fuel elements. The neutron flux level is doubled when core is shifted from 5MW to 10 MW. Total nuclear power peaking factor of the core is 2.03. The analysis shows that the core can be operated safely at 5 MW with a flow rate of 520 meter cube per hour and at 10 MW with a flow rate of 900 meter cube per hour. (A.B.). 10 figs

Comparison of the FRM-II HEU design with an alternative LEU design

International Nuclear Information System (INIS)

Mo, S.C.; Hanan, N.A.; Matos, J.E.

2004-01-01

The FRM-II reactor design of the Technical University of Munich has a compact core that utilizes fuel plates containing highly-enriched uranium (HEU, 93%). This paper presents an alternative core design utilizing low-enriched uranium (LEU, 3 that provides nearly the same neutron flux for experiments as the HEU design, but has a less favourable fuel cycle economy. If an LEU fuel with a uranium density of 6.0 - 6.5 g/cm 3 . were developed, the alternative design would provide the same neutron flux and use the same number of cores per year as the HEU design. The results of this study show that there are attractive possibilities for using LEU fuel instead of HEU fuel in the FRM-II. Further optimization of the LEU design and near-term availability of LEU fuel with a uranium density greater than 4.8 g/cm 3 would enhance the performance of the LEU core. The REKIR Program is ready to exchange information with the Technical University of Munich to resolve any differences that may exist and to identify design modifications that would optimize reactor performance utilizing LEU fuel. (author)

Analysis of the loss of coolant accident for LEU cores of Pakistan research reactor-1

International Nuclear Information System (INIS)

Khan, L.A.; Bokhari, I.H.; Raza, S.H.

1993-12-01

Response of LEU cores for PARR-1 to a Loss of Coolant Accident (LOCA) has been studied. It has been assumed that pool water drains out to double ended rupture of primary coolant pipe or complete shearing of an experimental beam tube. Results show that for an operating power level of 10 MW, both the first high power and equilibrium cores would enter into melting conditions if the pool drain time is less than 22 h and 11 h respectively. However, an Emergency Core Cooling System (ECCS) capable of spraying the core at flow rate of 8.3 m/sup 3/h, for the above mentioned duration, would keep the peak core temperature much below the critical value. Maximum operating power levels below which melting would not occur have been assessed to 3.4 MW and 4.8 MW, respectively, for the first high power and equilibrium cores. (author) 5 figs

Analysis of the TREAT LEU Conceptual Design

Energy Technology Data Exchange (ETDEWEB)

Connaway, H. M. [Argonne National Lab. (ANL), Argonne, IL (United States); Kontogeorgakos, D. C. [Argonne National Lab. (ANL), Argonne, IL (United States); Papadias, D. D. [Argonne National Lab. (ANL), Argonne, IL (United States); Brunett, A. J. [Argonne National Lab. (ANL), Argonne, IL (United States); Mo, K. [Argonne National Lab. (ANL), Argonne, IL (United States); Strons, P. S. [Argonne National Lab. (ANL), Argonne, IL (United States); Fei, T. [Argonne National Lab. (ANL), Argonne, IL (United States); Wright, A. E. [Argonne National Lab. (ANL), Argonne, IL (United States)

2016-03-01

Analyses were performed to evaluate the performance of the low enriched uranium (LEU) conceptual design fuel for the conversion of the Transient Reactor Test Facility (TREAT) from its current highly enriched uranium (HEU) fuel. TREAT is an experimental nuclear reactor designed to produce high neutron flux transients for the testing of reactor fuels and other materials. TREAT is currently in non-operational standby, but is being restarted under the U.S. Department of Energy’s Resumption of Transient Testing Program. The conversion of TREAT is being pursued in keeping with the mission of the Department of Energy National Nuclear Security Administration’s Material Management and Minimization (M3) Reactor Conversion Program. The focus of this study was to demonstrate that the converted LEU core is capable of maintaining the performance of the existing HEU core, while continuing to operate safely. Neutronic and thermal hydraulic simulations have been performed to evaluate the performance of the LEU conceptual-design core under both steady-state and transient conditions, for both normal operation and reactivity insertion accident scenarios. In addition, ancillary safety analyses which were performed for previous LEU design concepts have been reviewed and updated as-needed, in order to evaluate if the converted LEU core will function safely with all existing facility systems. Simulations were also performed to evaluate the detailed behavior of the UO₂-graphite fuel, to support future fuel manufacturing decisions regarding particle size specifications. The results of these analyses will be used in conjunction with work being performed at Idaho National Laboratory and Los Alamos National Laboratory, in order to develop the Conceptual Design Report project deliverable.

Neutronic analysis of a reference LEU core for Pakistan research reactor using oxide fuel

International Nuclear Information System (INIS)

Akhtar, K.M.; Qazi, M.K.; Bokhari, I.H.; Khan, L.A.; Pervez, S.

1988-07-01

Neutronic analysis of a 10 MW reference core for PARR, having 28 fresh LEU fuel elements arranged in a 6x5 configuration has been carried out using standard computer codes WIMS-D, EXTERMINATOR-II, and CITATION. Total nuclear power peaking of 3.2 has bee found to occur in the fuel plate adjacent to the water filled central flux trap at the depth of 43.8 cm from the top of the active core. Replacement of water in central flux trap with an aluminum block, having a 50 mm diameter water filled irradiation channel changes the flux profiles in fuel, core side flux trap and reflector. The thermal flux in the central flux trap decreases by about 53%. Therefore some of the fuel elements will have to be removed and the new configuration has to be analysed to determine the first operating core. However, after achieving some burn-up and confirmation from thermal hydraulic analysis, the core configuration analysed, will be the final working core. (orig./A.B.)

Neutronic Analysis of the RSG-GAS Compact Core without CIP Silicide 3.55 g U/cc and 4.8 g U/cc

International Nuclear Information System (INIS)

Jati S; Lily S; Tukiran S

2004-01-01

Fuel conversion from U 3 O 8 -Al to U 3 Si 2 -Al 2.96 g U/cc density in the RSG-GAS core had done successfully step by step since 36 th core until 44 th core. So that, since the 45 th core until now (48 th core) had been using full of silicide 2.96 g U/cc. Even though utilization program of silicide fuel with high density (3.55 g U/cc and 4.8 g U/cc) and optimize operation of RSG-GAS core under research. Optimalitation of core with increasing operation cycle have been analyzing about compact core. The mean of compact core is the RSG-GAS core with decrease number of IP or CIP position irradiation. In this research, the neutronic calculation to cover RSG-GAS core and RSG-GAS core without CIP that are using U 3 Si 2 -Al 2.96 g U/cc, 3.55 g U/cc and 4.8 g U/cc had done. Two core calculation done at 15 MW power using SRAC-ASMBURN code. The calculation result show that fuel conversion from 2.96 g U/cc density to 3.55 g U/cc and 4.8 g U/cc will increasing cycle length for both RSG-GAS core and RSG-GAS compact core without CIP. However, increasing of excess reactivity exceeded from nominal value of first design that 9.2%. Change of power peaking factor is not show significant value and still less than 1.4. Core fuelled with U 3 Si 2 -Al 4.8 g U/cc density have maximum discharge burn-up which exceeded from licensing value (70%). RSG-GAS compact core without CIP fuelled U 3 Si 2 -Al 2.96 g U/cc have longer cycle operation then RSG-GAS core and fulfil limitation neutronic parameter at the first design value. (author)

Nuclear criticality assessment of LEU and HEU fuel element storage

International Nuclear Information System (INIS)

Pond, R.B.; Matos, J.E.

1984-01-01

Criticality aspects of storing LEU (20%) and HEU (93%) fuel elements have been evaluated as a function of 235 U loading, element geometry, and fuel type. Silicide, oxide, and aluminide fuel types have been evaluated ranging in 235 U loading from 180 to 620 g per element and from 16 to 23 plates per element. Storage geometry considerations have been evaluated for fuel element separations ranging from closely packed formations to spacings of several centimeters between elements. Data are presented in a form in which interpolations may be made to estimate the eigenvalue of any fuel element storage configuration that is within the range of the data. (author)

The status of HEU and LEU core conversion activities at the Jamaica SLOWPOKE

Energy Technology Data Exchange (ETDEWEB)

Preston, J.; Grant, C., E-mail: john.preston@uwimona.edu.jm [Univ. of the West Indies, Mona Campus, International Centre for Environmental and Nuclear Sciences, Kingston (Jamaica)

2013-07-01

The SLOWPOKE reactor in Jamaica has been operated by the International Centre for Environmental and Nuclear Sciences, University of the West Indies since 1984, mainly for the purpose of Neutron Activation Analysis. The HEU core with current utilization has another 14 years of operation, before the addition of a large beryllium annulus would be required to further extend the life-time by 15 years. However, in keeping with the spirit of the Reduced Enrichment for Research and Test Reactors (RERTR) program, the decision was taken in 2003 to convert the core from HEU to LEU, inline with those at the Ecole Polytechnic and RMC SLOWPOKE facilities. This paper reports on the current status of the conversion activities, including key fuel manufacture and regulatory issues, which have seen substantial progress during the last year. A timetable for the complete process is given, and provided that the fuel fabrication can be completed in the estimated 18 months, the core conversion should be accomplished by the end of 2014. (author)

Preliminary Results of Ancillary Safety Analyses Supporting TREAT LEU Conversion Activities

Energy Technology Data Exchange (ETDEWEB)

Brunett, A. J. [Argonne National Lab. (ANL), Argonne, IL (United States); Fei, T. [Argonne National Lab. (ANL), Argonne, IL (United States); Strons, P. S. [Argonne National Lab. (ANL), Argonne, IL (United States); Papadias, D. D. [Argonne National Lab. (ANL), Argonne, IL (United States); Hoffman, E. A. [Argonne National Lab. (ANL), Argonne, IL (United States); Kontogeorgakos, D. C. [Argonne National Lab. (ANL), Argonne, IL (United States); Connaway, H. M. [Argonne National Lab. (ANL), Argonne, IL (United States); Wright, A. E. [Argonne National Lab. (ANL), Argonne, IL (United States)

2015-10-01

The Transient Reactor Test Facility (TREAT), located at Idaho National Laboratory (INL), is a test facility designed to evaluate the performance of reactor fuels and materials under transient accident conditions. The facility, an air-cooled, graphite-moderated reactor designed to utilize fuel containing high-enriched uranium (HEU), has been in non-operational standby status since 1994. Currently, in support of the missions of the Department of Energy (DOE) National Nuclear Security Administration (NNSA) Material Management and Minimization (M3) Reactor Conversion Program, a new core design is being developed for TREAT that will utilize low-enriched uranium (LEU). The primary objective of this conversion effort is to design an LEU core that is capable of meeting the performance characteristics of the existing HEU core. Minimal, if any, changes are anticipated for the supporting systems (e.g. reactor trip system, filtration/cooling system, etc.); therefore, the LEU core must also be able to function with the existing supporting systems, and must also satisfy acceptable safety limits. In support of the LEU conversion effort, a range of ancillary safety analyses are required to evaluate the LEU core operation relative to that of the existing facility. These analyses cover neutronics, shielding, and thermal hydraulic topics that have been identified as having the potential to have reduced safety margins due to conversion to LEU fuel, or are required to support the required safety analyses documentation. The majority of these ancillary tasks have been identified in [1] and [2]. The purpose of this report is to document the ancillary safety analyses that have been performed at Argonne National Laboratory during the early stages of the LEU design effort, and to describe ongoing and anticipated analyses. For all analyses presented in this report, methodologies are utilized that are consistent with, or improved from, those used in analyses for the HEU Final Safety Analysis

Refractory silicides for integrated circuits

International Nuclear Information System (INIS)

Murarka, S.P.

1980-01-01

Transition metal silicides have, in the past, attracted attention because of their usefulness as high temperature materials and in integrated circuits as Schottky barrier and ohmic contacts. More recently, with the increasing silicon integrated circuits (SIC) packing density, the line widths get narrower and the sheet resistance contribution to the RC delay increases. The possibility of using low resistivity silicides, which can be formed directly on the polysilicon, makes these silicides highly attractive. The usefulness of a silicide metallization scheme for integrated circuits depends, not only on the desired low resistivity, but also on the ease with which the silicide can be formed and patterned and on the stability of the silicides throughout device processing and during actual device usage. In this paper, various properties and the formation techniques of the silicides have been reviewed. Correlations between the various properties and the metal or silicide electronic or crystallographic structure have been made to predict the more useful silicides for SIC applications. Special reference to the silicide resistivity, stress, and oxidizability during the formation and subsequent processing has been given. Various formation and etching techniques are discussed

The series production in a standardized fabrication line for silicide fuels and commercial aspects

International Nuclear Information System (INIS)

Wehner, E.L.; Hassel, H.W.

1987-01-01

NUKEM has been responsible for the development and fabrication of LEU fuel elements for MTR reactors under the frame of the German AF program since 1979. The AF program is part of the international RERTR efforts, which were initiated by the INFCE Group in 1978. This paper describes the actual status of development and the transition from the prototype to the series production in a standardized manufacturing line for silicide fuels at NUKEM. Technical provisions and a customer oriented standardized product range aim at an economized manufacturing. (Author)

Fabrication, fabrication control and in-core follow up of 4 LEU leader fuel elements based on U3Si2 in RECH-1

International Nuclear Information System (INIS)

Chavez, J.C.; Barrera, M.; Olivares, L.; Lisboa, J.

1999-01-01

The RECH-1 MTR reactor has been converted from HEU to MEU (45% enrichment) and the decision to a LEU (20% enrichment) conversion was taken some years ago. This LEU conversion decision involved a local fuel development and fabrication based on U 3 Si 2 -Al dispersion fuel, and a fabrication qualification stage that resulted in four fuel elements fully complying with established fabrication standards for this type of fuel. This report-presents relevant points of these four leaders fuel elements fabrication, in particular a fuel plate core homogeneity control development. A summary of the intended in core follow-up studies for the leaders fuel elements is also presented here. (author)

Studies of mixed HEU-LEU-MTR cores using 3D models

Energy Technology Data Exchange (ETDEWEB)

Haenggi, P.; Lehmann, E.; Hammer, J.; Christen, R. [Paul Scherrer Institute, Villigen (Switzerland)

1997-08-01

Several different core loadings were assembled at the SAPHIR research reactor in Switzerland combining the available types of MTR-type fuel elements, consisting mainly of both HEU and LEU fuel. Bearing in mind the well known problems which can occur in such configurations (especially power peaking), investigations have been carried out for each new loading with a 2D neutron transport code (BOXER). The axial effects were approximated by a global buckling value and therefore the radial effects could be studied in considerably detail. Some of the results were reported at earlier RERTR meetings and were compared to those obtained by other methods and with experimental values. For the explicit study of the third dimension of the core, another code (SILWER), which has been developed in PSI for LWR power plant cores, has been selected. With the help of an adapted model for the MTR-core of SAPHIR, several important questions have been addressed. Among other aspects, the estimation of the axial contribution to the hot channel factors, the influence of the control rod position and of the Xe-poisoning on the power distribution were studied. Special attention was given to a core position where a new element was assumed placed near a empty, water filled position. The comparison of elements of low and high enrichments at this position was made in terms of the induced power peaks, with explicit consideration of axial effects. The program SILWER has proven to be applicable to MTR-cores for the investigation of axial effects. For routine use as for the support of reactor operation, this 3D code is a good supplement to the standard 2D model.

Analysis Of Temperature Effects On Reactivity Of The Rsg-Gas Core Using Silicide Fuels

International Nuclear Information System (INIS)

Surbakti, Tukiran; Pinem, Surian

2001-01-01

RSG-GAS has been operating using new silicide fuels so that it is necessary to estimate and to measure the effect of temperature on reactivity of the core. The parameters to be determined due to temperature effect are reactivity coefficient of moderator temperature, temperature coefficient of fuel element and power reactivity coefficient. By doing a couple compensation method, determination of reactivity coefficient as well as the reactivity coefficient of moderator temperature can be obtained. Furthermore, coefficient of the reactivity was successfully estimated using the combination of WIMS-D4 and Batan-2DIFF. The cell calculation was done by using WIMS-D4 code to get macroscopic cross section and Batan-2DIFF code is used for core calculation. The calculation and experimental results of reactivity coefficient do not show any deviation from RSG-GAS safety margin. The results are -2,84 sen/ o C, -1,29 sen/MW and -0,64 sen/ o C for reactivity coefficients of temperature, power, fuel element and moderator temperature, respectively. All of 3 parameters are absolutely met with safety criteria

Verification of maximum radial power peaking factor due to insertion of FPM-LEU target in the core of RSG-GAS reactor

Energy Technology Data Exchange (ETDEWEB)

Setyawan, Daddy, E-mail: d.setyawan@bapeten.go.id [Center for Assessment of Regulatory System and Technology for Nuclear Installations and Materials, Indonesian Nuclear Energy Regulatory Agency (BAPETEN), Jl. Gajah Mada No. 8 Jakarta 10120 (Indonesia); Rohman, Budi [Licensing Directorate for Nuclear Installations and Materials, Indonesian Nuclear Energy Regulatory Agency (BAPETEN), Jl. Gajah Mada No. 8 Jakarta 10120 (Indonesia)

2014-09-30

Verification of Maximum Radial Power Peaking Factor due to insertion of FPM-LEU target in the core of RSG-GAS Reactor. Radial Power Peaking Factor in RSG-GAS Reactor is a very important parameter for the safety of RSG-GAS reactor during operation. Data of radial power peaking factor due to the insertion of Fission Product Molybdenum with Low Enriched Uranium (FPM-LEU) was reported by PRSG to BAPETEN through the Safety Analysis Report RSG-GAS for FPM-LEU target irradiation. In order to support the evaluation of the Safety Analysis Report incorporated in the submission, the assessment unit of BAPETEN is carrying out independent assessment in order to verify safety related parameters in the SAR including neutronic aspect. The work includes verification to the maximum radial power peaking factor change due to the insertion of FPM-LEU target in RSG-GAS Reactor by computational method using MCNP5and ORIGEN2. From the results of calculations, the new maximum value of the radial power peaking factor due to the insertion of FPM-LEU target is 1.27. The results of calculations in this study showed a smaller value than 1.4 the limit allowed in the SAR.

Stylized whole-core benchmark of the Integral Inherently Safe Light Water Reactor (I2S-LWR) concept

International Nuclear Information System (INIS)

Hon, Ryan; Kooreman, Gabriel; Rahnema, Farzad; Petrovic, Bojan

2017-01-01

Highlights: • A stylized benchmark specification of the I2S-LWR core. • A library of cross sections were generated in both 8 and 47 groups. • Monte Carlo solutions generated for the 8 group library using MCNP5. • Cross sections and pin fission densities provided in journal’s repository. - Abstract: The Integral, Inherently Safe Light Water Reactor (I 2 S-LWR) is a pressurized water reactor (PWR) concept under development by a multi-institutional team led by Georgia Tech. The core is similar in size to small 2-loop PWRs while having the power level of current large reactors (∼1000 MWe) but using uranium silicide fuel and advanced stainless steel cladding. A stylized benchmark specification of the I 2 S-LWR core has been developed in order to test whole-core neutronics codes and methods. For simplification the core was split into 57 distinct material regions for cross section generation. Cross sections were generated using the lattice physics code HELIOS version 1.10 in both 8 and 47 groups. Monte Carlo solutions, including eigenvalue and pin fission densities, were generated for the 8 group library using MCNP5. Due to space limitations in this paper, the full cross section library and normalized pin fission density results are provided in the journal’s electronic repository.

The status of HEU to LEU core conversion activities at the Jamaica SLOWPOKE

Energy Technology Data Exchange (ETDEWEB)

Preston, J.; Grant, C., E-mail: john.preston@uwimona.edu.jm [Univ. of the West Indies, Mona Campus, International Centre for Environmental and Nuclear Sciences, Mona (Jamaica)

2012-12-15

The SLOWPOKE reactor in Jamaica has been operated by the International Centre for Environmental and Nuclear Sciences, University of the West Indies since 1984, mainly for the purpose of Neutron Activation Analysis. The HEU core with current utilization has another 14 years of operation, before the addition of a large beryllium annulus would be required to further extend the life-time by 15 years. However, in keeping with the spirit of the Reduced Enrichment for Research and Test Reactors (RERTR) program, the decision was taken in 2003 to convert the core from HEU to LEU, in line with those at the Ecole Polytechnic and RMC SLOWPOKE facilities. This paper reports on the current status of the conversion activities, including key fuel manufacture and regulatory issues, which have seen substantial progress during the last year. A timetable for the complete process is given, and provided that the fuel fabrication can be completed in the estimated 18 months, the core conversion should be accomplished by the end of 2014. (author)

A neutronic feasibility study for LEU conversion of the Brookhaven Medical Research Reactor (BMRR).

Energy Technology Data Exchange (ETDEWEB)

Hanan, N. A.

1998-01-14

A neutronic feasibility study for converting the Brookhaven Medical Research Reactor from HEU to LEU fuel was performed at Argonne National Laboratory in cooperation with Brookhaven National Laboratory. Two possible LEU cores were identified that would provide nearly the same neutron flux and spectrum as the present HEU core at irradiation facilities that are used for Boron Neutron Capture Therapy and for animal research. One core has 17 and the other has 18 LEU MTR-type fuel assemblies with uranium densities of 2.5g U/cm{sup 3} or less in the fuel meat. This LEU fuel is fully-qualified for routine use. Thermal hydraulics and safety analyses need to be performed to complete the feasibility study.

Performance of PARR-1 with LEU Fuel

International Nuclear Information System (INIS)

Pervez, S.; Latif, M.; Bokhari, I.H.; Bakhtyar, S.

2005-01-01

Pakistan Research Reactor (PARR-1) went critical in 1965 with HEU fuel. The reactor core was converted to LEU fuel with power upgradation from 5 MW to 10 MW in 1992. The reactor has been operated with LEU fuel for about 10,000 hours and has produced about 66,000 MWh energy up to now. Average burn up of the irradiated fuel is about 42 %. The fuel performance during the last 12 years has been excellent. Post irradiation visual inspection of the fuel has revealed no abnormality. During operation there have been no signs of releases in the pool water establishing the full integrity of this fuel. The reactor has been mainly utilized for radioisotope production, beam tube experiments including neutron diffraction studies, neutron radiography etc. Studies have been completed to operate the reactor with a mixed core (HEU + LEU) to utilize the less burned HEU fuel elements. A major project of production of fission Moly using PARR-1 is in the final stages. (author)

Preliminary LEU fuel cycle analyses for the Belgian BR2 reactor

International Nuclear Information System (INIS)

Deen, J.R.; Snelgrove, J.L.

1986-01-01

Fuel cycle calculations have been performed with reference HEU fuel and LEU fuel using Cd wires or boron as burnable absorbers. The 235 U content in the LEU element has increased 20% to 480g compared to the reference HEU element. The number of fuel plates has remained unchanged while the fuel meat thickness has increased to 0.76 mm from 0.51 mm. The LEU meat density is 5.1 Mg U/m 3 . The reference fuel cycle was a 31 element core operating at 56 MW with a 19.8 day cycle length and eight fresh elements loaded per cycle. Comparable fuel cycle characteristics can be achieved using the proposed LEU fuel element with either Cd wires or boron burnable absorbers. The neutron flux for E/sub n/ > 1 eV changes very little (<5%) in LEU relative to HEU cores. Thermal flux reductions are 5 to 10% in non-fueled positions, and 20 to 30% in fuel elements

Status of reduced enrichment program for research reactors in Japan

International Nuclear Information System (INIS)

Kaieda, Keisuke; Baba, Osamu; Nagaoka, Yoshiharu; Kanda, Keiji; Nakagome, Yoshihiro

1999-01-01

The reduced enrichment programs for the JRR-3M, JRR-4 and JMTR of Japan Atomic Energy Research Institute (JAERI) have been completed. The KUR of Kyoto University Research Reactor Institute (KURRI) has been partially completed and is still in progress under the Joint Study Program with Argonne National Laboratory (ANL). The JRR-3M commenced using LEU silicide fuel elements instead of LEU aluminide fuel elements in September, 1999. The Japanese Government approved a cancellation of the KUHFR Project in February 1991, and April 1994 the U.S. Government gave an approval to utilize HEU fuel in the KUR instead of the KUHFR. Therefore, the KUR will be operated with HEU fuel until March 2004, then the full core conversion with LEU silicide will be done. The first shipment of spent fuels since 1974 was done in August, 1999. (author)

Effect of Utilization of Silicide Fuel with the Density 4.8 gU/cc on the Kinetic Parameters of RSG-GAS Reactor

International Nuclear Information System (INIS)

Setiyanto; Sembiring, Tagor M.; Pinem, Surian

2007-01-01

Presently, the RSG-GAS reactor using silicide fuel element of 2.96 gU/cc. For increasing reactor operation time, its planning to change to higher density fuel. The kinetic calculation of silicide core with density 4.8 gU/cc has been carried out, since it has an influence on the reactor operation safety. The calculated kinetic parameters are the effective delayed neutron fraction, the delayed neutron decay constant, prompt neutron lifetime and feedback reactivity coefficient very important for reactor operation safety. the calculation is performed in 2-dimensional neutron diffusion-perturbation method using modified Batan-2DIFF code. The calculation showed that the effective delayed neutron fraction is 7. 03256x10 -03 , total delay neutron time constant is 7.85820x10 -02 s -1 and the prompt neutron lifetime is 55.4900 μs. The result of prompt neutron lifetime smaller 10 % compare with silicide fuel of 4.8 gU/cc. The calculated results showed that all of the feedback reactivity coefficient silicide core 4.8 gU/cc is negative. Totally, the feedback reactivity coefficient of silicide fuel of 4.8 gU/cc is 10% less than that of silicide fuel of 2.96 gU/cc. The results shown that kinetic parameters result decrease compared with the silicide core with density 2.96 gU/cc, but no significant influence in the RSG-GAS reactor operation. (author)

Reduced Enrichment for Research and Test Reactors. Proceedings of the XVIII international meeting

Energy Technology Data Exchange (ETDEWEB)

NONE

2004-07-01

Almost 50 papers presented were showing the status of the national programs related to conversion of research reactor cores from highly enriched (HEU) to low enriched uranium (LEU) fuel elements. Design of new fuel elements (uranium silicides) and safety related calculations were dealt with taking into account fuel cycle issues, meaning spent fuel storage and transportation. A number of presentations were devoted to Mo-99 production using LEU targets.

Reduced Enrichment for Research and Test Reactors. Proceedings of the XVIII international meeting

International Nuclear Information System (INIS)

2004-01-01

Almost 50 papers presented were showing the status of the national programs related to conversion of research reactor cores from highly enriched (HEU) to low enriched uranium (LEU) fuel elements. Design of new fuel elements (uranium silicides) and safety related calculations were dealt with taking into account fuel cycle issues, meaning spent fuel storage and transportation. A number of presentations were devoted to Mo-99 production using LEU targets

Surface morphology of erbium silicide

International Nuclear Information System (INIS)

Lau, S.S.; Pai, C.S.; Wu, C.S.; Kuech, T.F.; Liu, B.X.

1982-01-01

The surface of rare-earth silicides (Er, Tb, etc.), formed by the reaction of thin-film metal layers with a silicon substrate, is typically dominated by deep penetrating, regularly shaped pits. These pits may have a detrimental effect on the electronic performance of low Schottky barrier height diodes utilizing such silicides on n-type Si. This study suggests that contamination at the metal-Si or silicide-Si interface is the primary cause of surface pitting. Surface pits may be reduced in density or eliminated entirely through either the use of Si substrate surfaces prepared under ultrahigh vacuum conditions prior to metal deposition and silicide formation or by means of ion irradiation techniques. Silicide layers formed by these techniques possess an almost planar morphology

Development of U6Fe-Al dispersions for the use of LEU in research and test reactors

International Nuclear Information System (INIS)

Nazare, S.

1983-01-01

For some time now, efforts are being made to develop fuel dispersions that would permit the use of low (approx. 20% 235-U) enriched uranium (LEU) instead of the currently used highly (approx. 93% 235-U) enriched uranium (HEU) in research and test reactors. Since penalties in the performance of the reactor have to be avoided, the 235-U content in the dispersion has at least to be retained at current levels. On account of their high U-densities, the major development effort has been focussed on the uranium silicides (U 3 Si, U 3 Si(Al), and U 3 Si 2 -based dispersions). With silicides as dispersants, it is possible to fabricate fuel element plates with U-densities in the dispersion of about 6.0 gU/cm 3 . In comparison to the silicides, the U 6 Fe-phase offers several advantages namely: higher U-density (approx. 17.0 gU/cm 3 ); relative ease of formation compared to U 3 Si; possible advantages with regard to reprocessing of the spent fuel due to the absence of silicon. The studies outlined here were performed with a view to investigating the preparation, reaction behavior and dimensional stability after heat treatment of U 6 Fe-Al dispersions

Development of U6Fe-Al dispersions for the use of LEU in research and test reactors

International Nuclear Information System (INIS)

Nazare, S.

1983-01-01

For some time now, efforts are being made to develop fuel dispersions that would permit the use of low (∼ 20% 235-U) enriched uranium (LEU) instead of the currently used highly (∼ 93% 235-U) enriched uranium (HEU) in research and test reactors. Since penalties in the performance of the reactor have to be avoided, the 235-U content in the dispersion has at least to be retained at current levels. On account of their high U-densities, the major development effort has been focussed on the uranium silicides [U 3 Si, U 3 Si(Al), and U 3 Si 2 - based dispersions. With silicides as dispersants, it is possible to fabricate fuel element plates with U-densities in the dispersion of about 6.0 g U/cm 3 . In comparison to the silicides, the U 6 Fe-phase offers several advantages namely: - higher U-density (∼ 17.0 g U/cm 3 ); - relative ease of formation compared to U 3 Si; - possible advantages with regard to reprocessing of the spent fuel due to the absence of silicon. The studies outlined here were therefore performed with a view to investigating the preparation, reaction behaviour and dimensional stability after heat treatment of U 6 Fe-Al dispersions

Post-pulse detail metallographic examinations of low-enriched uranium silicide plate-type miniature fuel

International Nuclear Information System (INIS)

Yanagisawa, Kazuaki

1991-10-01

Pulse irradiation at Nuclear Safety Research Reactor (NSRR) was performed using low-enriched (19.89 w% 235 U) unirradiated silicide plate-type miniature fuel which had a density of 4.8 gU/cm 3 . Experimental aims are to understand the dimensional stability and to clarify the failure threshold of the silicide plate-type miniature fuel under power transient conditions through post-pulse detail metallographic examinations. A silicide plate-type miniature fuel was loaded into an irradiation capsule and irradiated by a single pulse. Deposited energies given in the experiments were 62, 77, 116 and 154 cal/g·fuel, which lead to corresponding peak fuel plate temperatures, 201 ± 28degC, 187 ± 10degC, 418 ± 74degC and 871 ± 74degC, respectively. Below 400degC, reliability and dimensional stability of the silicide plate fuel was sustained, and the silicide plate fuel was intact. Up to 540degC, wall-through intergranular crackings occurred in the Al-3%Mg alloy cladding. With the increase of the temperature, the melting of the aluminum cladding followed by recrystallization, the denudation of fuel core and the plate-through intergranular cracking were observed. With the increase of the temperature beyond 400degC, the bowing of fuel plate became significant. Above the temperature of 640degC molten aluminum partially reacted with the fuel core, partially flowed downward under the influence of surface tension and gravity, and partially formed agglomerations. Judging from these experimental observations, the fuel-plate above 400degC tends to reduce its dimensional stability. Despite of the apparent silicide fuel-plate failure, neither generation of pressure pulse nor that of mechanical energy occurred at all. (J.P.N.)

Neutronic calculations in core conversion of the IAN-R1 research reactor from MTR HEU to TRIGA LEU fuel

International Nuclear Information System (INIS)

Sarta Fuentes, Jose A.; Castiblanco, L.A.

2003-01-01

With cooperation of the International Atomic Energy Agency (IAEA), neutronic calculations were carried out for conversion of the Ian-R1 Reactor from MTR-HEU fuel to TRIGA-LEU fuel. In order to establish a staff for neutronic calculation at the Instituto de Cancan's Nucleares y Energia s Alternatives (INEA) a program was established. This program included training, acquisition of hardware, software and calculation for the core with MTR-HEU fuel , enriched nominally to 93% and calculation for several arrangements with the TRIGA-LEU fuel, enriched to 19.7%. The results were verified and compared with several groups of calculation at the Instituto Nacional de Investigaciones Nucleares (ININ) in Mexico, and General Atomics (GA) in United States. As a result of this program, several technical reports have been wrote. (author)

Reactivity management and burn-up management on JRR-3 silicide-fuel-core

International Nuclear Information System (INIS)

Kato, Tomoaki; Araki, Masaaki; Izumo, Hironobu; Kinase, Masami; Torii, Yoshiya; Murayama, Yoji

2007-08-01

On the conversion from uranium-aluminum-dispersion-type fuel (aluminide fuel) to uranium-silicon-aluminum-dispersion-type fuel (silicide fuel), uranium density was increased from 2.2 to 4.8 g/cm 3 with keeping uranium-235 enrichment of 20%. So, burnable absorbers (cadmium wire) were introduced for decreasing excess reactivity caused by the increasing of uranium density. The burnable absorbers influence reactivity during reactor operation. So, the burning of the burnable absorbers was studied and the influence on reactor operation was made cleared. Furthermore, necessary excess reactivity on beginning of operation cycle and the time limit for restart after unplanned reactor shutdown was calculated. On the conversion, limit of fuel burn-up was increased from 50% to 60%. And the fuel exchange procedure was changed from the six-batch dispersion procedure to the fuel burn-up management procedure. The previous estimation of fuel burn-up was required for the planning of fuel exchange, so that the estimation was carried out by means of past operation data. Finally, a new fuel exchange procedure was proposed for effective use of fuel elements. On the procedure, burn-up of spent fuel was defined for each loading position. The average length of fuel's staying in the core can be increased by two percent on the procedure. (author)

Nuclear and radiological safety in the substitution process of the fuel HEU to LEU 30/20 in the Reactor TRIGA Mark III of the ININ

International Nuclear Information System (INIS)

Hernandez G, J.

2012-10-01

Inside the safety initiative in the international ambit, with the purpose of reducing the risks associated with the use of high enrichment nuclear fuels (HEU) for different proposes to the peaceful uses of the nuclear energy, Mexico contributes by means of the substitution of the high enrichment fuel HEU for low enrichment fuel LEU 30/20 in the TRIGA Mark III Reactor, belonging to Instituto Nacional de Investigaciones Nucleares (ININ). The conversion process was carried out by means of the following activities: analysis of the proposed core, reception and inspection of the fuel LEU 30/20, the discharge of the fuels of the mixed reactor core, shipment of the fuels HEU fresh and irradiated to the origin country, reload activities with the fuels LEU 30/20 and parameters measurement of the core operation. In order to maintaining the personnel's integrity and infrastructure associated to the Reactor, during the whole process the measurements of nuclear and radiological safety were controlled to detail, in execution with the license requirements of the installation. This work describes the covering activities and radiological inspections more relevant, as well as the measurements of radiological control implemented with base in the estimate of the equivalent dose of the substitution process. (Author)

Greek research reactor performance characteristics after addition of beryllium reflector and LEU fuel

International Nuclear Information System (INIS)

Deen, J.R.; Snelgrove, J.L.; Papastergiou, C.

1992-01-01

The GRR-1 is a 5-MW pool-type, light-water-moderated and-cooled reactor fueled with MTR-type fuel elements. Recently received Be reflector blocks will soon be added to the core to add additional reactivity until fresh LEU fuel arrives. REBUS-3 xy fuel cycle analyses, using burnup dependent cross sections, were performed to assist in fuel management decisions for the water- and Be-reflected HEU nonequilibrium cores. Cross sections generated by EPRI-CELL have been benchmarked to identical VIM Monte Carlo models. The size of the Be-reflected LEU core has been reduced to 30 elements compared to 35 for the HEU water-reflected core, and an equilibrium cycle calculation has been performed

Irradiation experiment conceptual design parameters for MURR LEU U-Mo fuel conversion

International Nuclear Information System (INIS)

Stillman, J.; Feldman, E.; Stevens, J.; Wilson, E.

2013-03-01

This report contains the results of reactor design and performance calculations for conversion of the University of Missouri Research Reactor (MURR) from the use of highly-enriched uranium (HEU) fuel to the use of low-enriched uranium (LEU) fuel. The analyses were performed by staff members of the Global Threat Reduction Initiative (GTRI) Reactor Conversion Program at the Argonne National Laboratory (ANL) and the MURR Facility. The core conversion to LEU is being performed with financial support from the U. S. government. In the framework of its non-proliferation policies, the international community presently aims to minimize the amount of nuclear material available that could be used for nuclear weapons. In this geopolitical context most research and test reactors, both domestic and international, have started a program of conversion to the use of LEU fuel. A new type of LEU fuel based on an alloy of uranium and molybdenum (U-Mo) is expected to allow the conversion of U.S. domestic high performance reactors like MURR. This report presents the nominal steady-state irradiation conditions of a key set of plates containing peak irradiation parameters found in MURR cores fueled with the LEU monolithic U-Mo alloy fuel with 10 wt% Mo.

Feasibility study for LEU conversion of the WWR-K reactor at the Institute of Nuclear Physics in Kazakhstan using a 5-tube fuel assembly

International Nuclear Information System (INIS)

Hanan, N.A.; Liaw, J.R.; Matos, J.E.

2005-01-01

A feasibility study by the RERTR program for possible LEU conversion of the 6 MW WWR-K reactor concludes that conversion is feasible using an LEU 5-tube Russian fuel assembly design. This 5-tube design is one of several LEU fuel assembly designs being studied (Ref. 1) for possible use in this reactor. The 5-tube assembly contains 200 g 235 U with an enrichment of 19.7% in four cylindrical inner tubes and an outer hexagonal tube with the same external dimensions as the current HEU (36%) 5-tube fuel assembly, which contains 112.5 g 235 U. The fuel meat material, LEU UO 2 -Al dispersion fuel with ∼ 2.5 g U/cm 3 , has been extensively irradiation tested in a number of reactors with uranium enrichments of 36% and 19.7%. Since the 235 U loading of the LEU assemblies is much larger than the HEU assemblies, a smaller LEU core with five rows of fuel assemblies is possible (instead of six rows of fuel assemblies in the HEU core). This smaller LEU core would consume about 60% as many fuel assemblies per year as the current HEU core and provide thermal neutron fluxes in the inner irradiation channels that are ∼ 17% larger than with the present HEU core. The current 21 day cycle length would be maintained and the average discharge burnup would be ∼ 42%. Neutron fluxes in the five outer irradiation channels would be smaller in the LEU core unless these channels can be moved closer to the LEU fuel assemblies. Results show that the smaller LEU core would meet the reactor's shutdown margin requirements and would have an adequate thermal-hydraulic safety margin to onset of nucleate boiling. (author)

Mo-99 production on a LEU solution reactor

International Nuclear Information System (INIS)

Brown, R.W.; Thome, L.A.; Khvostionov, V.Y.

2005-01-01

A pilot homogenous reactor utilizing LEU has been developed by the Kurchatov Institute in Moscow along with their commercial partner TCI Medical. This solution reactor operates at levels up to 50 kilowatts and has successfully produced high quality Mo-99 and Sr-89. Radiochemical extraction of medical radionuclides from the reactor solution is performed by passing the solution across a series of inorganic sorbents. This reactor has commercial potential for medical radionuclide production using LEU UO 2 SO 4 fuel. Additional development work is needed to optimize multiple 50 kilowatt cores while at the same time, optimizing production efficiency and capital expenditure. (author)

Status of LEU conversion program at CRNL

International Nuclear Information System (INIS)

Kennedy, I.C.

1991-01-01

After briefly reviewing the salient features of the NRU Reactor at Chalk River Nuclear Laboratories (CRNL), the progress of our LEU fuel development and testing program is described. The results (to date) of full-size prototype fuel-rod irradiations are reviewed, and the status of the new fuel-fabrication facility on the site is updated. Although development work is proceeding on U 3 Si 2 dispersions, all indications so far are that CRNL's U 3 Si fuel is fully acceptable for reactor operation. Fuel rods from the new fabrication shop will be installed in NRU in 1990, and the complete core conversion of NRU to LEU driver fuel is expected by 1991. (orig.)

Multi-layered silicides coating for vanadium alloys for generation IV reactors

International Nuclear Information System (INIS)

Mathieu, S.; Chaia, N.; Vilasi, M.; Le Flem, M.

2012-01-01

The halide-activated pack-cementation technique was employed to fabricate a diffusion coating that is resistant both to isothermal and to cyclic oxidation in air at 650 degrees C on the surface of the V-4Cr-4Ti vanadium alloy that is a potential core component of future nuclear systems. A thermodynamic assessment determined the deposit conditions in terms of master alloy, activator, filler and temperature. The partial pressures of the main gaseous species (SiCl 4 , SiCl 2 and VCl 2 ) in the pack were calculated with the master alloy Si and the mixture VSi 2 + Si. The VSi 2 + Si master alloy was used to limit vanadium loss from the surface. The obtained coating consisted of multi-layered V x Si y silicides with an outer layer of VSi 2 . This silicide developed a protective layer of silica at 650 degrees C in air and was not susceptible to the pest phenomenon, unlike other refractory silicides (MoSi 2 , NbSi 2 ). We suggest that VSi 2 exhibits no risk of rapid degradation in the gas fast reactor (GFR) conditions. (authors)

The Environment Shapes the Inner Vestibule of LeuT

DEFF Research Database (Denmark)

Sohail, Azmat; Jayaraman, Kumaresan; Venkatesan, Santhoshkannan

2016-01-01

Human neurotransmitter transporters are found in the nervous system terminating synaptic signals by rapid removal of neurotransmitter molecules from the synaptic cleft. The homologous transporter LeuT, found in Aquifex aeolicus, was crystallized in different conformations. Here, we investigated t...... showed TM1A movements, consistent with the simulations, confirming a substantially different inward-open conformation in lipid bilayer from that inferred from the crystal structure....... the inward-open state of LeuT. We compared LeuT in membranes and micelles using molecular dynamics simulations and lanthanide-based resonance energy transfer (LRET). Simulations of micelle-solubilized LeuT revealed a stable and widely open inward-facing conformation. However, this conformation was unstable...... in a membrane environment. The helix dipole and the charged amino acid of the first transmembrane helix (TM1A) partitioned out of the hydrophobic membrane core. Free energy calculations showed that movement of TM1A by 0.30 nm was driven by a free energy difference of ~15 kJ/mol. Distance measurements by LRET...

Irradiation behavior of miniature experimental uranium silicide fuel plates

International Nuclear Information System (INIS)

Hofman, G.L.; Neimark, L.A.; Mattas, R.F.

1983-01-01

Uranium silicides, because of their relatively high uranium density, were selected as candidate dispersion fuels for the higher fuel densities required in the Reduced Enrichment Research and Test Reactor (RERTR) Program. Irradiation experience with this type of fuel, however, was limited to relatively modest fission densities in the bulk from, on the order of 7 x 10 20 cm -3 , far short of the approximately 20 x 10 20 cm -3 goal established for the RERTR program. The purpose of the irradiation experiments on silicide fuels on the ORR, therefore, was to investigate the intrinsic irradiation behavior of uranium silicide as a dispersion fuel. Of particular interest was the interaction between the silicide particles and the aluminum matrix, the swelling behavior of the silicide particles, and the maximum volume fraction of silicide particles that could be contained in the aluminum matrix

Innovative nuclear thermal rocket concept utilizing LEU fuel for space application

International Nuclear Information System (INIS)

Nam, Seung Hyun; Venneri, Paolo; Choi, Jae Young; Jeong, Yong Hoon; Chang, Soon Heung

2015-01-01

Space is one of the best places for humanity to turn to keep learning and exploiting. A Nuclear Thermal Rocket (NTR) is a viable and more efficient option for human space exploration than the existing Chemical Rockets (CRs) which are highly inefficient for long-term manned missions such as to Mars and its satellites. NERVA derived NTR engines have been studied for the human missions as a mainstream in the United States of America (USA). Actually, the NERVA technology has already been developed and successfully tested since 1950s. The state-of-the-art technology is based on a Hydrogen gas (H_2) cooled high temperature reactor with solid core utilizing High-Enriched Uranium (HEU) fuel to reduce heavy metal mass and to use fast or epithermal neutron spectrums enabling simple core designs. However, even though the NTR designs utilizing HEU is the best option in terms of rocket performance, they inevitably provoke nuclear proliferation obstacles on all Research and Development (R and D) activities by civilians and non-nuclear weapon states, and its eventual commercialization. To surmount the security issue to use HEU fuel for a NTR, a concept of the innovative NTR engine, Korea Advanced NUclear Thermal Engine Rocket utilizing Low-Enriched Uranium fuel (KANUTER-LEU) is presented in this paper. The design goal of KANUTER-LEU is to make use of a LEU fuel for its compact reactor, but does not sacrifice the rocket performance relative to the traditional NTRs utilizing HEU. KANUTER-LEU mainly consists of a fission reactor utilizing H_2 propellant, a propulsion system and an optional Electricity Generation System as a bimodal engine. To implement LEU fuel for the reactor, the innovative engine adopts W-UO_2 CERMET fuel to drastically increase uranium density and thermal neutron spectrum to improve neutron economy in the core. The moderator and structural material selections also consider neutronic and thermo-physical characteristics to reduce non-fission neutron loss and

Recent Advances in Nb-silicide in-situ composites

International Nuclear Information System (INIS)

Bewlay, B.P.; Jackson, M.R.; Subramanian, P.R.; Briant, C.L.

2001-01-01

In-situ composites based on Nb silicides have great potential for future high-temperature applications. These Nb-silicide composites combine a ductile Nb-based matrix with high-strength silicides. With the appropriate combination of alloying elements, such as Ti, Hf, Cr, AI, it is possible to achieve a promising balance of fracture toughness, high-temperature creep performance, and oxidation resistance. This paper will describe the effect of volume fraction of silicide on microstructure, high-temperature creep performance, and oxidation resistance. The ratio of Nb:(W+Ti) is critical in determining both creep rate and oxidation performance. If this ratio goes below ∼1.5, the creep rate increases substantially. In more complex silicide-based systems, other intermetallics, such as laves phases and a boron-rich T-2 phase, are added for oxidation resistance. To understand the role of each phase on the creep resistance and oxidation performance of these composites, we determined the creep and oxidation behavior of the individual phases and composites at temperatures up to 1200 o C. These data allow quantification of the load-bearing capability of the individual phases in the Nb-silicide based in-situ composites. (author)

LEU-fueled SLOWPOKE-2 modelling with MCNP4A

International Nuclear Information System (INIS)

Pierre, J.R.M.; Bonin, H.W.J.

1996-01-01

Following the commissioning of the Low Enrichment Uranium (LEU) Fueled SLOWPOKE-2 research reactor at Royal Military College,excess reactivity measurements were conducted over a range of temperature and power. Given the advance in computer technology, the use of Monte Carlo N-Particle Transport Code System MCNP 4A appeared possible for the simulation of the LEU-fueled SLOWPOKE-2 reactor core, and this work demonstrates that this is indeed the case. MCNP 4A is a full three dimensional program allowing the user to enter a large amount of complexity. The limit on the geometry complexity is the computing time required to achieve a reasonable standard deviation. To this point several models of the SLOWPOKE-2 have been developed giving some insight on the sensitivity of the code. MCNP4A can use various cross section libraries. The aim of this work is to calculate accurately the reactivity of the core and reproduce The temperature trend of the reactivity. The model preserved as much as possible the details of the core and facility in order to allow further study in the flux mapping

TiSi2 integrity within a doped silicide process step

International Nuclear Information System (INIS)

Crean, G.M.; Cole, P.D.; Stoemenos, J.

1993-01-01

Degradation of arsenic implanted titanium silicide (TiSi 2 ) thin films as a result of thermal processing for shallow junction formation is investigated. Significant arsenic diffusion from the silicide overlayer into the silicon substrate has been detected by Rutherford Backscattering Spectrometry at drive-in temperatures > 1,050 C. Cross-sectional transmission electron micrographs have shown the silicide film become increasingly non-uniform as the thermal budget increases, ultimately leading to discontinuities forming in the silicide film. This observed degradation of the titanium silicide film is also supported by sheet resistance measurements which show the film to degrade significantly above a threshold thermal budget

Subsurface contributions in epitaxial rare-earth silicides

Energy Technology Data Exchange (ETDEWEB)

Luebben, Olaf; Shvets, Igor V. [Centre for Research on Adaptive Nanostructures and Nanodevices (CRANN), School of Physics, Trinity College, Dublin (Ireland); Cerda, Jorge I. [Instituto de Ciencia de Materiales de Madrid, ICMM-CSIC, Cantoblanco, Madrid (Spain); Chaika, Alexander N. [Institute of Solid State Physics, RAS, Chernogolovka (Russian Federation)

2015-07-01

Metallic thin films of heavy rare-earth silicides epitaxially grown on Si(111) substrates have been widely studied in recent years because of their appealing properties: unusually low values of the Schottky barrier height, an abrupt interface, and a small lattice mismatch. Previous studies also showed that these silicides present very similar atomic and electronic structures. Here, we examine one of these silicides (Gd{sub 3}Si{sub 5}) using scanning tunneling microscopy (STM) image simulations that go beyond the Tersoff-Hamann approach. These simulations strongly indicate an unusual STM depth sensitivity for this system.

Analytical analyses of startup measurements associated with the first use of LEU fuel in Romania's 14-MW TRIGA reactor

International Nuclear Information System (INIS)

Bretscher, M.M.; Snelgrove, J.L.; Ciocanescu, M.

1992-01-01

The 14-MW TRIGA steady state reactor (SSR) is located in Pitesti, Romania. Beginning with an HEU core (10 wt% U), the reactor first went critical in November 1979 but was shut down ten years later because of insufficient excess reactivity. Last November the Institute for Nuclear Research (INR), which operates the SSR, received from the ANL RERTR program a shipment of 125 LEU pins fabricated by General Atomics and of the same geometry as the original fuel but with an enrichment of 19.7% 235U and a loading of 45 wt% U. Using 100 of these pins, four LEU clusters, each containing a 5 x 5 square array of fuel rods, were assembled. These four LEU clusters replaced the four most highly burned HEU elements in the SSR. The reactor resumed operations last February with a 35-element mixed HEU/LEU core configuration. In preparation for full power operation of the SSR with this mixed HEU/LEU core, a number of measurements were made. These included control rod calibrations, excess reactivity determinations, worths of experiment facilities, reaction rate distributions, and themocouple measurements of fuel temperatures as a function of reactor power. This paper deals with a comparison of some of these measured reactor parameters with corresponding analytical calculations

Morphology of Si/tungsten-silicides/Si interlayers

International Nuclear Information System (INIS)

Theodore, N.; Secco d'Aragona, F.; Blackstone, S.

1992-01-01

Tungsten and tungsten-silicides are of interest for semiconductor technology because of their refractory nature, low electrical-resistivity and high electromigration-resistance. This paper presents the first formation of buried tungsten-silicide layers in silicon, by proximity adhesion. The interlayers, created by a combination of chemical vapor-deposition (CVD) and proximity-adhesion were studied using transmission electron-microscopy (TEM). The behavior of the layers in the presence and absence of an adjacent silicon-dioxide interlayer was also investigated. Buried silicide layers were successfully formed with or without the adjacent silicon-dioxide. The silicide formed continuous layers with single grains encompassing the width of the interlayer. Individual grains were globular, with cusps at grain boundaries. This caused interlayer-thicknesses to be non-uniform, with lower thickness values being present at the cusps. Occasional voids were observed at grain-boundary cusps. The voids were smaller and less frequent in the presence of an adjacent oxide-layer, due to flow of the oxide during proximity adhesion. Electron-diffraction revealed a predominance of tungsten-disilicide in the interlayers, with some free tungsten being present. Stresses in the silicide layers caused occasional glide dislocations to propagate into the silicon substrate beneath the interlayers. The dislocations propagate only ∼100 nm into the substrate and therefore should not be detrimental to use of the buried layers. Occasional precipitates were observed at the end of glide-loops. These possibly arise due to excess tungsten from the interlayer diffusion down the glide dislocation to finally precipitate out as tungsten-silicide

Neutronic analysis for conversion of the Ghana Research Reactor-1 facility using Monte Carlo methods and UO{sub 2} LEU fuel

Energy Technology Data Exchange (ETDEWEB)

Anim-Sampong, S.; Akaho, E.H.K.; Maakuu, B.T.; Gbadago, J.K. [Ghana Research Reactor-1 Centre, Dept. of Nuclear Engineering and Materials Science, National Nuclear Research Institute, Ghana Atomic Energy Commission, Legon, Accra (Ghana); Andam, A. [Kwame Nkrumah Univ. of Science and Technology, Dept. of Physics (Ghana); Liaw, J.J.R.; Matos, J.E. [Argonne National Lab., RERTR Programme, Div. of Nuclear Engineering (United States)

2007-07-01

Monte Carlo particle transport methods and software (MCNP) have been applied to the modelling, simulation and neutronic analysis for the conversion of the HEU-fuelled (high enrichment uranium) core of the Ghana Research Reactor-1 (GHARR-1) facility. The results show that the MCNP model of the GHARR-1 facility, which is a commercial version of the Miniature Neutron Source Reactor (MNSR) is good as the simulated neutronic and other reactor physics parameters agree with very well with experimental and zero power results. Three UO{sub 2} LEU (low enrichment uranium) fuels with different enrichments (12.6% and 19.75%), core configurations, core loadings were utilized in the conversion studies. The nuclear criticality and kinetic parameters obtained from the Monte Carlo simulation and neutronic analysis using three UO{sub 2} LEU fuels are in close agreement with results obtained for the reference 90.2% U-Al HEU core. The neutron flux variation in the core, fission chamber and irradiation channels for the LEU UO{sub 2} fuels show the same trend as the HEU core as presented in the paper. The Monte Carlo model confirms a reduction (8% max) in the peak neutron fluxes simulated in the irradiation channels which are utilized for experimental and commercial activities. However, the reductions or 'losses' in the flux levels neither affects the criticality safety, reactor operations and safety nor utilization of the reactor. Employing careful core loading optimization techniques and fuel loadings and enrichment, it is possible to eliminate the apparent reductions or 'losses' in the neutron fluxes as suggested in this paper. Concerning neutronics, it can be concluded that all the 3 LEU fuels qualify as LEU candidates for core conversion of the GHARR-1 facility.

Comparison of HEU and LEU neutron spectra in irradiation facilities at the Oregon State TRIGA® Reactor

International Nuclear Information System (INIS)

Schickler, R.A.; Marcum, W.R.; Reese, S.R.

2013-01-01

Highlights: • The Oregon State TRIGA ® Reactor neutron spectra is characterized herein. • Neutron spectra between highly enriched uranium and low enriched uranium cores are compared. • Discussion is given as to differences between HEU and LEU core spectra results and impact on experiments. -- Abstract: In 2008, the Oregon State TRIGA ® Reactor (OSTR) was converted from highly enriched uranium (HEU) fuel lifetime improvement plan (FLIP) fuel to low-enriched uranium (LEU) fuel. This effort was driven and supported by the Department of Energy's (DoE's) Reduced Enrichment for Research and Test Reactors (RERTR) program. The basis behind the RERTR program's ongoing conversion effort is to reduce the nuclear proliferation risk of civilian research and test reactors. The original intent of the HEU FLIP fuel was to provide fuel to research reactors that could be utilized for many years before a necessary refueling cycle. As a research reactor, the OSTR provides irradiation facilities for a variety of applications, such as activation analysis, fission-track dating, commercial isotope production, neutron radiography, prompt gamma characterization, and many others. In order to accurately perform these research functions, several studies had been conducted on the HEU FLIP fuel core to characterize the neutron spectra in various experimental facilities of the OSTR (Tiyapun, 1997; Ashbaker, 2005). As useful as these analyses were, they are no longer valid due to the change in fuel composition and the resulting alteration of core performance characteristics. Additionally, the core configuration (fuel reconfiguration) was altered between the HEU and LEU cores. This study characterizes the neutron spectra in various experimental facilities within and around the current LEU core. It also compares the spectra to that which was yielded in the HEU core through use of Monte Carlo n-Particle 5 (MCNP5) and experimental adjustment via a least-squares technique. The quantification of

Analyses on Silicide Coating for LOCA Resistant Cladding

Energy Technology Data Exchange (ETDEWEB)

Sweidan, Faris B.; Lee, You Ho; Ryu, Ho Jin [KAIST, Daejeon (Korea, Republic of)

2015-10-15

A particular focus of accident-tolerant fuel has been cladding due to the rapid high-temperature oxidation of zirconium-based cladding with the evolution of H2 when steam is a reactant. Some key features of the coated cladding include high-temperature resistance to oxidation, lower processing temperatures, and a high melting point of the coating. Zirconium alloys exhibit a reasonably high melting temperature, so a coating for the cladding is appealing if the coating increases the high-temperature resistance to oxidation. In this case, the cladding is protected from complete oxidation. The cladding coating involves the application of zirconium silicide onto Zr-based cladding. Zirconium silicide coating is expected to produce a glassy layer that becomes more protective at elevated temperature. For this reason, silicide coatings on cladding offer the potential for improved reliability at normal operating temperatures and at the higher transient temperatures encountered during accidents. Although ceramic coatings are brittle and may have weak points to be used as coating materials, several ceramic coatings were successful and showed adherent behavior and high resistance to oxidation. In this study, the oxidation behavior of zirconium silicide and its oxidation kinetics are analyzed. Zirconium silicide is a new suggested material to be used as coatings on existing Zr-based cladding alloys, the aim of this study is to evaluate if zirconium silicide is applicable to be used, so they can be more rapidly developed using existing cladding technology with some modifications. These silicide coatings are an attractive alternative to the use of coatings on zirconium claddings or to the lengthy development of monolithic ceramic or ceramic composite claddings and coatings.

Analyses on Silicide Coating for LOCA Resistant Cladding

International Nuclear Information System (INIS)

Sweidan, Faris B.; Lee, You Ho; Ryu, Ho Jin

2015-01-01

A particular focus of accident-tolerant fuel has been cladding due to the rapid high-temperature oxidation of zirconium-based cladding with the evolution of H2 when steam is a reactant. Some key features of the coated cladding include high-temperature resistance to oxidation, lower processing temperatures, and a high melting point of the coating. Zirconium alloys exhibit a reasonably high melting temperature, so a coating for the cladding is appealing if the coating increases the high-temperature resistance to oxidation. In this case, the cladding is protected from complete oxidation. The cladding coating involves the application of zirconium silicide onto Zr-based cladding. Zirconium silicide coating is expected to produce a glassy layer that becomes more protective at elevated temperature. For this reason, silicide coatings on cladding offer the potential for improved reliability at normal operating temperatures and at the higher transient temperatures encountered during accidents. Although ceramic coatings are brittle and may have weak points to be used as coating materials, several ceramic coatings were successful and showed adherent behavior and high resistance to oxidation. In this study, the oxidation behavior of zirconium silicide and its oxidation kinetics are analyzed. Zirconium silicide is a new suggested material to be used as coatings on existing Zr-based cladding alloys, the aim of this study is to evaluate if zirconium silicide is applicable to be used, so they can be more rapidly developed using existing cladding technology with some modifications. These silicide coatings are an attractive alternative to the use of coatings on zirconium claddings or to the lengthy development of monolithic ceramic or ceramic composite claddings and coatings

Behavior of silicon in nitric media. Application to uranium silicides fuels reprocessing

International Nuclear Information System (INIS)

Cheroux, L.

2001-01-01

Uranium silicides are used in some research reactors. Reprocessing them is a solution for their cycle end. A list of reprocessing scenarios has been set the most realistic being a nitric dissolution close to the classic spent fuel reprocessing. This uranium silicide fuel contains a lot of silicon and few things are known about polymerization of silicic acid in concentrated nitric acid. The study of this polymerization allows to point out the main parameters: acidity, temperature, silicon concentration. The presence of aluminum seems to speed up heavily the polymerization. It has been impossible to find an analytical technique smart and fast enough to characterize the first steps of silicic acid polymerization. However the action of silicic species on emulsions stabilization formed by mixing them with an organic phase containing TBP has been studied, Silicon slows down the phase separation by means of oligomeric species forming complex with TBP. The existence of these intermediate species is short and heating can avoid any stabilization. When non irradiated uranium silicide fuel is attacked by a nitric solution, aluminum and uranium are quickly dissolved whereas silicon mainly stands in solid state. That builds a gangue of hydrated silica around the uranium silicide particulates without preventing uranium dissolution. A small part of silicon passes into the solution and polymerize towards the highly poly-condensed forms, just 2% of initial silicon is still in molecular form at the end of the dissolution. A thermal treatment of the fuel element, by forming inter-metallic phases U-Al-Si, allows the whole silicon to pass into the solution and next to precipitate. The behavior of silicon in spent fuels should be between these two situations. (author)

A neutronic feasibility study for LEU conversion of the WWR-M reactor at Gatchina

International Nuclear Information System (INIS)

Petrov, Yu. V.; Erykalov, A.N.; Onegin, M.S.

2000-01-01

In this report we present the results of computations of the full scale reactor core with HEU (90%), MEU (36%) and LEU (19.75%) fuel. The reactor computer model for the MCU RFFI Monte Carlo code includes all peculiarities of the core. Calculations show that a uranium density of 3.3gU/cm 3 of MEU (36%) fuel and 8/25gU/cm 3 of LEU (19.75%) in WWR-M5 fuel assembly (FA) geometry is required to match the fuel cycle length of the HEU (90%) case with the same end of cycle (EOEC) excess reactivity. For the equilibrium fuel cycle the fuel burnup and poisoning, the fast and thermal neutron fluxes, the reactivity worth of control rods were calculated for the reference case with HEU (90%) FA and for the MEU and LEU FA. The relative accuracy of this neutronic feasibility study of fuel enrichment reduction of the WWR-M reactor in Gatchina is sufficient to start the fabrication feasibility study of MEU (36%) WWR-M5 fuel assemblies. At the present stage of technology it seems hardly possible to manufacture LEU (19.75%) fuel elements in WWR-M5 geometry due to too high uranium density. Only a future R and D can solve the problem. (author)

Program description for the qualification of CNEA - Argentina as a supplier of LEU silicide fuel and post-irradiation examinations plan for the first prototype irradiated in Argentina

International Nuclear Information System (INIS)

Rugirello, Gabriel; Adelfang, Pablo; Denis, Alicia; Zawerucha, Andres; Marco, Agustin di; Guillaume, Eduardo; Sbaffoni, Monica; Lacoste, Pablo

1998-01-01

In this report we present a description of the ongoing and future stages of the program for the qualification of CNEA, Argentina, as a supplier of low enriched uranium silicide fuel elements for research reactor. Particularly we will focus on the characteristics of the future irradiation experiment on a new detachable prototype, the post-irradiation examinations (PIE) plan for the already irradiated prototype PO4 and an overview of the recently implemented PIE facilities and equipment. The program is divided in several steps, some of which have been already completed. It concludes: development of the uranium silicide fissile material, irradiation and PIE of several full-scale prototypes. Important investments have been already carried out in the facilities for the FE production and PIE. (author)

Room temperature ferromagnetic gadolinium silicide nanoparticles

Science.gov (United States)

Hadimani, Magundappa Ravi L.; Gupta, Shalabh; Harstad, Shane; Pecharsky, Vitalij; Jiles, David C.

2018-03-06

A particle usable as T1 and T2 contrast agents is provided. The particle is a gadolinium silicide (Gd5Si4) particle that is ferromagnetic at temperatures up to 290 K and is less than 2 .mu.m in diameter. An MRI contrast agent that includes a plurality of gadolinium silicide (Gd.sub.5Si.sub.4) particles that are less than 1 .mu.m in diameter is also provided. A method for creating gadolinium silicide (Gd5Si4) particles is also provided. The method includes the steps of providing a Gd5Si4 bulk alloy; grinding the Gd5Si4 bulk alloy into a powder; and milling the Gd5Si4 bulk alloy powder for a time of approximately 20 minutes or less.

Neutronic feasibility studies for LEU conversion of the HFR Petten reactor

International Nuclear Information System (INIS)

Hanan, N.A.; Deen, J.R.; Matos, J.E.; Hendriks, J.A.; Thijssen, P.J.M.; Wijtsma, F.J.

2000-01-01

Design and safety analyses to determine an optimum LEU fuel assembly design using U 3 Si 2 -Al fuel with up to 4.8 g/cm 3 for conversion of the HFR Petten reactor were performed by the RERTR program in cooperation with the Joint Research Centre and NRG. Credibility of the calculational methods and models were established by comparing calculations with recent measurements by NRG for a core configuration set up for this purpose. This model and methodology were then used to study various LEU fissile loading and burnable poison options that would satisfy specific design criteria. (author)

A comparative and predictive study of the annual fuel cycle costs for HEU and LEU fuels in the High Flux Reactor, Petten, 1985-1993

Energy Technology Data Exchange (ETDEWEB)

Moss, R L; May, P

1985-07-01

The internationally agreed constraint on availability of supply of HEU fuels to Research and Test Reactors has necessitated that a cost analysis be carried out to determine the financial effect of converting the core of the HFR from HEU to LEU fuels. A computer program, written at Petten and based on information extracted from studies in Europe and the USA, identifies the major cost variables to be manufacturing, uranium, reprocessing and transport costs. Comparison between HEU and LEU cores have been carried out and includes the effects of inflation and exchange rate fluctuations. Conversion of the HFR core to LEU fuels is shown to be financially disadvantageous. (author)

A comparative and predictive study of the annual fuel cycle costs for HEU and LEU fuels in the High Flux Reactor, Petten, 1985-1993

International Nuclear Information System (INIS)

Moss, R.L.; May, P.

1985-01-01

The internationally agreed constraint on availability of supply of HEU fuels to Research and Test Reactors has necessitated that a cost analysis be carried out to determine the financial effect of converting the core of the HFR from HEU to LEU fuels. A computer program, written at Petten and based on information extracted from studies in Europe and the USA, identifies the major cost variables to be manufacturing, uranium, reprocessing and transport costs. Comparison between HEU and LEU cores have been carried out and includes the effects of inflation and exchange rate fluctuations. Conversion of the HFR core to LEU fuels is shown to be financially disadvantageous. (author)

RERTR program activities related to the development and application of new LEU fuels

International Nuclear Information System (INIS)

Travelli, A.

1983-01-01

The statue of the U.S. Reduced Enrichment Research and Test Reactor (RERTR) Program is reviewed. After a brief outline of RERTR Program objectives and goals, program accomplishments are discussed with emphasis on the development, demonstration and application of new LEU fuels. Most program activities have proceeded as planned, and a combination of two silicide fuels (U 3 Si 2 -Al and U 3 Si-Al) holds excellent promise for achieving the long-term program goals. Current plans and schedules project the uranium density of qualified RERTR fuels for plate-type reactors to grow by approximately 1 g U/cm 3 each year, from the current 1.7 g U/cm 3 to the 7.0 g U/cm 3 which will be reached in late 1988. The technical needs of research and test reactors for HEU exports are also forecasted to undergo a gradual but dramatic decline in the coming years

Palladium silicide - a new contact for semiconductor radiation detectors

International Nuclear Information System (INIS)

Totterdell, D.H.J.

1981-11-01

Silicide layers can be used as low resistance contacts in semiconductor devices. The formation of a metal rich palladium silicide Pd 2 Si is discussed. A palladium film 100A thick is deposited at 300 0 C and the resulting silicide layer used as an ohmic contact in an n + p silicon detector. This rugged contact has electrical characteristics comparable with existing evaporated gold contacts and enables the use of more reproducible bonding techniques. (author)

Experimental evaluation of new NEU cores in the UVAR

Energy Technology Data Exchange (ETDEWEB)

Farrar, P.; Hosticka, B.; Krause, D.; Mulder, R.; Rydin, R. [Univ. of Virginia, Charlottesville, VA (United States)

1997-08-01

The University of Virginia began working on converting the UVAR reactor to LEU fuel in the Spring of 1986. The Safety Analysis Report was completed and submitted to the NRC in late 1989. After review, the DOE order to manufacture LEU fuel was placed at B&W in March 1992, and the new fuel was received in January 1994. The 4-by-4 fully-graphite-reflected LEU-1 core went critical on April 20, 1994, and the 4-by-5 partially-graphite-reflected operational LEU-2 core went critical on April 29. Full power was achieved on May 12, 1994. Both cores behaved very much as originally predicted. All of the old HEU fuel has been shipped to Savannah River.

A study of CoSix silicide formed by recoil implantation

International Nuclear Information System (INIS)

Kwok, H.L.

1989-01-01

This work investigated the formation of CoSi x silicides on n-Si by recoil implantation through a thin cobalt layer using an inert gas ion beam. The results suggest the formation of a very shallow (35 to 45 nm) silicide surface layer under the specific conditions of preparation. The surface layer resistivity was comparable to values reported for Co 2 Si and CoSi, although below the surface, the resistivity decreased. This appeared to suggest a change-over from cobalt-rich silicides near the surface to a more conducting silicide (CoSi 2 ) at the interface. (author)

Fuel conversion of JRR-4 from HEU to LEU

International Nuclear Information System (INIS)

Ichikawa, Hiroki; Nakajima, Teruo

1997-01-01

Japanese JRR-4 (Japan Research Reactor No.4) is a pool type, light water moderated and cooled, ETR type fuel reactor used for Shielding experiments, isotope production, neutron activation analyses, Si doping, reactor students training. It acieved first criticality on January 28, 1965 with maximum thermal power 3.5MW. The standard core consistes of 20 Fuel elements, 7 control rods 5 Irradiation holes, neutron source, graphite reflectors. Available thermal flux is 7x1013 n/cm2/s. Within the RERTR program plans are made for core conversion from HEU to LEU

Assessment of assembly homogenized two-steps core dynamic calculations using direct whole core transport solutions

International Nuclear Information System (INIS)

Hursin, Mathieu; Downar, Thomas J.; Yoon, Joo Il; Joo, Han Gyu

2016-01-01

Highlights: • Reactivity initiated accident analysis with direct whole core transient transport code. • Comparison with usual “two steps” procedure. • Effect of effective delayed neutron fraction definition on energy deposition in the fuel. • Effect of homogenized few-group cross sections generation at the assembly level on energy deposition in the fuel. • Effect of effective fuel temperature definition on energy deposition in the fuel. - Abstract: The impact of the approximations in the “two-steps” procedure used in the current generation of nodal simulators for core transient calculations is assessed by using a higher order solution obtained from a direct, whole core, transient transport calculation. A control rod ejection accident in an idealized minicore is analyzed with PARCS, which uses the two-steps procedure and DeCART which provides the higher order solution. DeCART is used as lattice code to provide the homogenized cross sections and kinetics parameters to PARCS. The approximations made by using (1) the homogenized few-group cross sections and kinetic parameters generated at the assembly level, (2) an effective delayed neutrons fraction, (3) an effective fuel temperature and (4) the few-group formulation are investigated in terms of global and local core power behavior. The results presented in the paper show that the current two-steps procedure produces sufficiently accurate transient results with respect to the direct whole core calculation solution, provided that its parameters are carefully generated using the prescriptions described in the present article.

A neutronics study of LEU fuel options for the HFR-Petten

International Nuclear Information System (INIS)

Deen, J.R.; Snelgrove, J.L.

1985-01-01

The standard HEU fuel cycle characteristics are compared with those of several different LEU fuel cycles in the new vessel configuration. The primary design goals were to provide similar reactivity performance and neutron flux profiles with a minimal increase in 235 U loading. The fuel cycle advantages of Cd burnable absorbers over 10 B are presented. The LEU fuel cycle requirements were calculated also for an extended 32-day cycle and for a reload batch size reduction from six to five standard elements for the standard 26-day cycle. The effects of typical in-core experiments upon neutron flux profiles and fuel loading requirements are also presented. (author)

Performance and Fabrication Status of TREAT LEU Conversion Conceptual Design Concepts

Energy Technology Data Exchange (ETDEWEB)

IJ van Rooyen; SR Morrell; AE Wright; E. P Luther; K Jamison; AL Crawford; HT III Hartman

2014-10-01

Resumption of transient testing at the TREAT facility was approved in February 2014 to meet U.S. Department of Energy (DOE) objectives. The National Nuclear Security Administration’s Global Threat Reduction Initiative Convert Program is evaluating conversion of TREAT from its existing highly enriched uranium (HEU) core to a new core containing low enriched uranium (LEU). This paper describes briefly the initial pre-conceptual designs screening decisions with more detailed discussions on current feasibility, qualification and fabrication approaches. Feasible fabrication will be shown for a LEU fuel element assembly that can meet TREAT design, performance, and safety requirements. The statement of feasibility recognizes that further development, analysis, and testing must be completed to refine the conceptual design. Engineering challenges such as cladding oxidation, high temperature material properties, and fuel block fabrication along with neutronics performance, will be highlighted. Preliminary engineering and supply chain evaluation provided confidence that the conceptual designs can be achieved.

Comparison of HEU and LEU neutron spectra in irradiation facilities at the Oregon State TRIGA{sup ®} Reactor

Energy Technology Data Exchange (ETDEWEB)

Schickler, R.A., E-mail: robert.schickler@oregonstate.edu; Marcum, W.R., E-mail: wade.marcum@oregonstate.edu; Reese, S.R.

2013-09-15

Highlights: • The Oregon State TRIGA{sup ®} Reactor neutron spectra is characterized herein. • Neutron spectra between highly enriched uranium and low enriched uranium cores are compared. • Discussion is given as to differences between HEU and LEU core spectra results and impact on experiments. -- Abstract: In 2008, the Oregon State TRIGA{sup ®} Reactor (OSTR) was converted from highly enriched uranium (HEU) fuel lifetime improvement plan (FLIP) fuel to low-enriched uranium (LEU) fuel. This effort was driven and supported by the Department of Energy's (DoE's) Reduced Enrichment for Research and Test Reactors (RERTR) program. The basis behind the RERTR program's ongoing conversion effort is to reduce the nuclear proliferation risk of civilian research and test reactors. The original intent of the HEU FLIP fuel was to provide fuel to research reactors that could be utilized for many years before a necessary refueling cycle. As a research reactor, the OSTR provides irradiation facilities for a variety of applications, such as activation analysis, fission-track dating, commercial isotope production, neutron radiography, prompt gamma characterization, and many others. In order to accurately perform these research functions, several studies had been conducted on the HEU FLIP fuel core to characterize the neutron spectra in various experimental facilities of the OSTR (Tiyapun, 1997; Ashbaker, 2005). As useful as these analyses were, they are no longer valid due to the change in fuel composition and the resulting alteration of core performance characteristics. Additionally, the core configuration (fuel reconfiguration) was altered between the HEU and LEU cores. This study characterizes the neutron spectra in various experimental facilities within and around the current LEU core. It also compares the spectra to that which was yielded in the HEU core through use of Monte Carlo n-Particle 5 (MCNP5) and experimental adjustment via a least

Role of fission product in whole core accidents: research in the USA

International Nuclear Information System (INIS)

Jackson, J.F.; Deitrich, L.W.

1977-01-01

The techniques being developed in the United States for analyzing postulated whole-core accidents in LMFBRs are briefly reviewed. The key mechanistic analysis methods are discussed in detail. Important research projects in the area of fission product effects are examined. Some typical results on the role of fission products in whole-core accidents are presented

Development of low enrichment technologies for high density fuels and for isotope production targets

International Nuclear Information System (INIS)

Taboada, Horacio; Gonzalez, Alfredo G.

2005-01-01

Since more than twenty years ago, CNEA has carried out RERTR activities. Main goals are to convert the RA 6 reactor core from HEU to LEU, to get a comprehensive understanding of U-Mo/Al compounds phase formation in dispersed and monolithic fuels, to develop possible solutions to VHD dispersed and monolithic fuels technical problems, and to optimize techniques to recover U from silicide scrap samples. The future plans include: 1) Completion the RA 6 reactor conversion to LEU; 2) Qualification by irradiation of the promising solutions found for the high density fuels; 3) Irradiation of mini plates and full scale fuel assemblies at the RA 3 reactor and at higher flux and temperature reactors; 4) Optimization of LEU target and radiochemical techniques for radioisotope production. (author) [es

A study on improving the performance of a research reactor's equilibrium core

Directory of Open Access Journals (Sweden)

Muhammad Atta

2013-01-01

Full Text Available Utilizing low enriched uranium silicide fuel (U3Si2-Al of existing uranium density (3.285 g/cm3, different core configurations have been studied in search of an equilibrium core with an improved performance for the Pakistan Research Reactor-1. Furthermore, we have extended our analysis to the performance of higher density silicide fuels with a uranium density of 4.0 and 4.8 U g/cm3. The criterion used in selecting the best performing core was that of “unit flux time cycle length per 235U mass per cycle”. In order to analyze core performance by improving neutron moderation, utilizing higher-density fuel, the effect of the coolant channel width was also studied by reducing the number of plates in the standard/control fuel element. Calculations employing computer codes WIMSD/4 and CITATION were performed. A ten energy group structure for fission neutrons was used for the generation of microscopic cross-sections through WIMSD/4. To search the equilibrium core, two-dimensional core modelling was performed in CITATION. Performance indicators have shown that the higher-density uranium silicide-fuelled core (U density 4.8 g/cm3 without any changes in standard/control fuel elements, comprising of 15 standard and 4 control fuel elements, is the best performing of all analyzed cores.

Room temperature ferromagnetic gadolinium silicide nanoparticles

Energy Technology Data Exchange (ETDEWEB)

Hadimani, Magundappa Ravi L.; Gupta, Shalabh; Harstad, Shane; Pecharsky, Vitalij; Jiles, David C.

2018-03-06

A particle usable as T₁ and T₂ contrast agents is provided. The particle is a gadolinium silicide (Gd₅Si₄) particle that is ferromagnetic at temperatures up to 290 K and is less than 2 .mu.m in diameter. An MRI contrast agent that includes a plurality of gadolinium silicide (Gd.sub.5Si.sub.4) particles that are less than 1 .mu.m in diameter is also provided. A method for creating gadolinium silicide (Gd₅Si₄) particles is also provided. The method includes the steps of providing a Gd₅Si₄ bulk alloy; grinding the Gd₅Si₄ bulk alloy into a powder; and milling the Gd₅Si₄ bulk alloy powder for a time of approximately 20 minutes or less.

Safety And Transient Analyses For Full Core Conversion Of The Dalat Nuclear Research Reactor

International Nuclear Information System (INIS)

Luong Ba Vien; Le Vinh Vinh; Huynh Ton Nghiem; Nguyen Kien Cuong

2011-01-01

Preparing for full core conversion of Dalat Nuclear Research Reactor (DNRR), safety and transient analyses were carried out to confirm about ability to operate safely of proposed Low Enriched Uranium (LEU) working core. The initial LEU core consisting 92 LEU fuel assemblies and 12 Beryllium rods was analyzed under initiating events of uncontrolled withdrawal of a control rod, cooling pump failure, earthquake and fuel cladding fail. Working LEU core response were evaluated under these initial events based on RELAP/Mod3.2 computer code and other supported codes like ORIGEN, MCNP and MACCS2. Obtained results showed that safety of the reactor is maintained for all transients/accidents analyzed. (author)

Irradiation behavior of experimental miniature uranium silicide fuel plates

International Nuclear Information System (INIS)

Hofman, Gerard L.; Neimark, L.A.; Mattas, R.F.

1983-01-01

Uranium silicides, because of their relatively high uranium density, were selected as candidate dispersion fuels for the higher fuel densities required in the Reduced Enrichment Research and Test Reactor (RERTR) Program. Irradiation experience with this type of fuel, however, was limited to relatively modest fission densities in the bulk form, on the order of 7 x 10 20 cm -3 , far short of he approximately 20 x 10 20 cm -3 goal established for the RERTR Program. The purpose of the irradiation experiments on silicide fuels in the ORR, therefore, was to investigate the intrinsic irradiation behavior of uranium silicide as a dispersion fuel. Of particular interest was the interaction between the silicide particles and the aluminum matrix, the swelling behavior of the silicide particles, and the maximum volume fraction of silicide particles that could be contained in the aluminum matrix. The first group of experimental 'mini' fuel plates have recently reached the program's goal burnup and are in various stages of examination. Although the results to date indicate some limitations, it appears that within the range of parameters examined thus far the uranium silicide dispersion holds promise for satisfying most of the needs of the RERTR Program. The twelve experimental silicide dispersion fuel plates that were irradiated to approximately their goal exposure show the 30-vol % U 3 Si-Al plates to be in a stage of relatively rapid fission-gas-driven swelling at a fission density of 2 x 10 20 cm -3 . This fuel swelling will likely result in unacceptably large plate-thickness increases. The U 3 Si plates appear to be superior in this respect; however, they, too, are starting to move into the rapid fuel-swelling stage. Analysis of the currently available post irradiation data indicates that a 40-vol % dispersed fuel may offer an acceptable margin to the onset of unstable thickness changes at exposures of 2 x 10 21 fission/cm 3 . The interdiffusion between fuel and matrix

Determination of accurate metal silicide layer thickness by RBS

International Nuclear Information System (INIS)

Kirchhoff, J.F.; Baumann, S.M.; Evans, C.; Ward, I.; Coveney, P.

1995-01-01

Rutherford Backscattering Spectrometry (RBS) is a proven useful analytical tool for determining compositional information of a wide variety of materials. One of the most widely utilized applications of RBS is the study of the composition of metal silicides (MSi x ), also referred to as polycides. A key quantity obtained from an analysis of a metal silicide is the ratio of silicon to metal (Si/M). Although compositional information is very reliable in these applications, determination of metal silicide layer thickness by RBS techniques can differ from true layer thicknesses by more than 40%. The cause of these differences lies in how the densities utilized in the RBS analysis are calculated. The standard RBS analysis software packages calculate layer densities by assuming each element's bulk densities weighted by the fractional atomic presence. This calculation causes large thickness discrepancies in metal silicide thicknesses because most films form into crystal structures with distinct densities. Assuming a constant layer density for a full spectrum of Si/M values for metal silicide samples improves layer thickness determination but ignores the underlying physics of the films. We will present results of RBS determination of the thickness various metal silicide films with a range of Si/M values using a physically accurate model for the calculation of layer densities. The thicknesses are compared to scanning electron microscopy (SEM) cross-section micrographs. We have also developed supporting software that incorporates these calculations into routine analyses. (orig.)

Si-Ge Nano-Structured with Tungsten Silicide Inclusions

Science.gov (United States)

Mackey, Jon; Sehirlioglu, Alp; Dynys, Fred

2014-01-01

Traditional silicon germanium high temperature thermoelectrics have potential for improvements in figure of merit via nano-structuring with a silicide phase. A second phase of nano-sized silicides can theoretically reduce the lattice component of thermal conductivity without significantly reducing the electrical conductivity. However, experimentally achieving such improvements in line with the theory is complicated by factors such as control of silicide size during sintering, dopant segregation, matrix homogeneity, and sintering kinetics. Samples are prepared using powder metallurgy techniques; including mechanochemical alloying via ball milling and spark plasma sintering for densification. In addition to microstructural development, thermal stability of thermoelectric transport properties are reported, as well as couple and device level characterization.

Nuclear characteristics evaluation for Kyoto University Research Reactor with low-enriched uranium core

Energy Technology Data Exchange (ETDEWEB)

Nakajima, Ken; Unesaki, Hironobu [Kyoto University Research Reactor Institute, Kumatori-cho Sennan-gun Osaka (Japan)

2008-07-01

A project to convert the fuel of Kyoto University Research Reactor (KUR) from highly enriched uranium (HEU) to low-enriched uranium (LEU) is in progress as a part of RERTR program. Prior to the operation of LEU core, the nuclear characteristics of the core have been evaluated to confirm the safety operation. In the evaluation, nuclear parameters, such as the excess reactivity, shut down margin control rod worth, reactivity coefficients, were calculated, and they were compared with the safety limits. The results of evaluation show that the LEU core is able to satisfy the safety requirements for operation, i.e. all the parameters satisfy the safety limits. Consequently, it was confirmed that the LEU fuel core has the proper nuclear characteristics for the safety operation. (authors)

Toward whole-core neutron transport without spatial homogenization

International Nuclear Information System (INIS)

Lewis, E. E.

2009-01-01

Full text of publication follows: A long-term goal of computational reactor physics is the deterministic analysis of power reactor core neutronics without incurring significant discretization errors in the energy, spatial or angular variables. In principle, given large enough parallel configurations with unlimited CPU time and memory, this goal could be achieved using existing three-dimensional neutron transport codes. In practice, however, solving the Boltzmann equation for neutrons over the six-dimensional phase space is made intractable by the nature of neutron cross-sections and the complexity and size of power reactor cores. Tens of thousands of energy groups would be required for faithful cross section representation. Likewise, the numerous material interfaces present in power reactor lattices require exceedingly fine spatial mesh structures; these ubiquitous interfaces preclude effective implementation of adaptive grid, mesh-less methods and related techniques that have been applied so successfully in other areas of engineering science. These challenges notwithstanding, substantial progress continues in the pursuit for more robust deterministic methods for whole-core neutronics analysis. This paper examines the progress over roughly the last decade, emphasizing the space-angle variables and the quest to eliminate errors attributable to spatial homogenization. As prolog we briefly assess 1990's methods used in light water reactor analysis and review the lessons learned from the C5G7 benchmark exercises which were originated in 1999 to appraise the ability of transport codes to perform core calculations without homogenization. We proceed by examining progress over the last decade much of which falls into three areas. These may be broadly characterized as reduced homogenization, dynamic homogenization and planar-axial synthesis. In the first, homogenization in three-dimensional calculations is reduced from the fuel assembly to the pin-cell level. In the second

Synthesis and design of silicide intermetallic materials

Energy Technology Data Exchange (ETDEWEB)

Petrovic, J.J.; Castro, R.G.; Butt, D.P. [Los Alamos National Lab., NM (United States)] [and others

1997-04-01

The overall objective of this program is to develop structural silicide-based materials with optimum combinations of elevated temperature strength/creep resistance, low temperature fracture toughness, and high temperature oxidation and corrosion resistance for applications of importance to the U.S. processing industry. A further objective is to develop silicide-based prototype industrial components. The ultimate aim of the program is to work with industry to transfer the structural silicide materials technology to the private sector in order to promote international competitiveness in the area of advanced high temperature materials and important applications in major energy-intensive U.S. processing industries. The program presently has a number of developing industrial connections, including a CRADA with Schuller International Inc. targeted at the area of MoSi{sub 2}-based high temperature materials and components for fiberglass melting and processing applications. The authors are also developing an interaction with the Institute of Gas Technology (IGT) to develop silicides for high temperature radiant gas burner applications, for the glass and other industries. Current experimental emphasis is on the development and characterization of MoSi{sub 2}-Si{sub 3}N{sub 4} and MoSi{sub 2}-SiC composites, the plasma spraying of MoSi{sub 2}-based materials, and the joining of MoSi{sub 2} materials to metals.

The Ford Nuclear Reactor demonstration project for the evaluation and analysis of low enrichment fuel

International Nuclear Information System (INIS)

Kerr, W.; King, J.S.; Lee, J.C.; Martin, W.R.; Wehe, D.K.

1991-07-01

The whole-core LEU fuel demonstration project at the University of Michigan was begun in 1979 as part of the Reduced Enrichment Research and Test Reactor (RERTR) Program at Argonne National Laboratory. An LEU fuel design was selected which would produce minimum perturbations in the neutronic, operations, and safety characteristics of the 2-MW Ford Nuclear Reactor (FNR). Initial criticality with a full LEU core on December 8, 1981, was followed by low- and full-power testing of the fresh LEU core, transitional operation with mixed HEU-LEU configurations, and establishment of full LEU equilibrium core operation. The transition from the HEU to the LEU configurations was achieved with negligible impact on experimental utilization and safe operation of the reactor. 78 refs., 74 figs., 84 tabs

Full core operation in JRR-3 with LEU fuels

International Nuclear Information System (INIS)

Murayama, Y.; Issiki, M.

1995-01-01

The new JRR-3 a 20MWT swimming pool type research reactor, is made up of plate type LEU fuel elements with U-Al x fuel at 2.2 gU/cm 3 . Reconstruction work for the new JR-3 was a good success, and common operation started in November 1990, and 7 cycles (26 days operation/cycle) have passed. We have no experience in using such a high uranium density fuel element with aluminide fuel. So we plan to examine the condition of the irradiated fuel elements with three methods, that is, measurement of the value of FFD in operation, observation of external view of the fuels in refueling work and postirradiation examination after maximum burn-up will be established. In the results of the first two methods, the fuel elements of JRR-3 is burned up normally and have no evidence of failure. (author)

Magnesium silicide production and silane synthesis on its basis

International Nuclear Information System (INIS)

Taurbaev, T.I.; Mukashev, F.A.; Manakov, S.M.; Francev, U.V.; Kalblanbekov, B.M.; Akhter, P.; Abbas, M.; Hussain, A.

2003-01-01

We had developed an alternative method of production of magnesium silicide with use of ferroalloys of silicon. Magnesium silicide is raw material for silane synthesis. The essence of the method consist of sintering FS -75 (ferrosilicium with 75 % of silicon and 25 % of iron, made by ferroalloy factories) with metal magnesium at temperature of 650 deg. C. The X-ray analysis has shown formation of magnesium silicide. That is further used for synthesis of silane. The output of silane is 60 % in respect of the contents of silicon. After removing the water vapors the mass-spectrometer analysis has estimated the purity of silane as 99.95 % with no detection of phosphine and diborane. (author)

Thermal stability of Ni-Pt-Ta alloy silicides on epi-Si1-xCx

International Nuclear Information System (INIS)

Yoo, Jung-Ho; Chang, Hyun-Jin; Min, Byoung-Gi; Ko, Dae-Hong; Cho, Mann-Ho; Sohn, Hyunchul; Lee, Tae-Wan

2008-01-01

We investigated the silicide formation in Ni/epi-Si 1-x C x systems. Ni-Pt and Ni-Pt-Ta films were deposited on epi-Si 1-x C x /Si substrates by DC magnetron sputtering and processed at various temperatures. The sheet resistance of the silicide from the Ni alloy/epi-Si 1-x C x systems was maintained at low values compared to that from Ni/Si systems. By TEM and EDS analyses, we confirmed the presence of a Pt alloy layer at the top of the Ni-silicide layer. The stability of the silicide layer in the Ni alloy/epi-Si 1-x C x system is explained by not only the Pt rich layer on the top of the Ni-silicide layer, but also by the presence of a small amount of Pt in the Ni-silicide layer or at the grain boundaries. And both the thermal stability and the morphology of silicide were greatly improved by the addition of Ta in Ni-Pt films

LEU-plate irradiation at FRJ-2 (DIDO) under the German AF-programme

Energy Technology Data Exchange (ETDEWEB)

Groos, E; Krug, W; Seferiadis, J; Thamm, G

1985-07-01

10 LEU fuel plates (8 with uranium silicides max. U-density 6.1 g/cm{sup 3}) have been irradiated at FRJ-2 (DIDO) of KFA-Juelich till end of October 1984 during 321 full power days up to max. burnup of 2.41x10{sup 27} fissions/m{sup 3} without major interruptions and troubles. PIE began recently in KFA hot cells. Visual inspections revealed no damage or greater deformation for the majority of the plates, but red/brown coloured layers (partially peeled off) on the cladding over the fuel. Aluminium (oxide) is the chief constituent of the layer with smaller portions of Ni and Fe the latter causing the red/brown colour. The major part of the layer ({approx}50 {mu}m) most probably has been formed during 20 h immediately after experiment start-up under abnormal conditions of the coolant water. Gamma scanning has been completed. Dimensional measurements are under way confirming first observations of severe swelling (pillowing) of 1 plate. Density and blister testing as well as metallography and burnup analysis remain to be accomplished end of 1985/beginning of 1986. (author)

Mechanoactivation of chromium silicide formation in the SiC-Cr-Si system

Directory of Open Access Journals (Sweden)

Vlasova M.

2002-01-01

Full Text Available The processes of simultaneous grinding of the components of a SiC-Cr-Si mixture and further temperature treatment in the temperature range 1073-1793 K were studied by X-ray phase analysis, IR spectroscopy, electron microscopy, and X-ray microanalysis. It was established that, during grinding of the mixture, chromium silicides form. A temperature treatment completes the process. Silicide formation proceeds within the framework of the diffusion of silicon into chromium. In the presence of SiO2 in the mixture, silicide formation occurs also as a result of the reduction of silica by silicon and silicon carbide. The sintering of synthesized composite SiC-chromium silicides powders at a high temperature under a high pressure (T = 2073 K, P = 5 GPa is accompanied by the destruction of cc-SiC particles, the cc/3 transition in silicon carbide and deformation distortions of the lattices of chromium silicides.

Thermoelectric characteristics of Pt-silicide/silicon multi-layer structured p-type silicon

International Nuclear Information System (INIS)

Choi, Wonchul; Jun, Dongseok; Kim, Soojung; Shin, Mincheol; Jang, Moongyu

2015-01-01

Electric and thermoelectric properties of silicide/silicon multi-layer structured devices were investigated with the variation of silicide/silicon heterojunction numbers from 3 to 12 layers. For the fabrication of silicide/silicon multi-layered structure, platinum and silicon layers are repeatedly sputtered on the (100) silicon bulk substrate and rapid thermal annealing is carried out for the silicidation. The manufactured devices show ohmic current–voltage (I–V) characteristics. The Seebeck coefficient of bulk Si is evaluated as 195.8 ± 15.3 μV/K at 300 K, whereas the 12 layered silicide/silicon multi-layer structured device is evaluated as 201.8 ± 9.1 μV/K. As the temperature increases to 400 K, the Seebeck coefficient increases to 237.2 ± 4.7 μV/K and 277.0 ± 1.1 μV/K for bulk and 12 layered devices, respectively. The increase of Seebeck coefficient in multi-layered structure is mainly attributed to the electron filtering effect due to the Schottky barrier at Pt-silicide/silicon interface. At 400 K, the thermal conductivity is reduced by about half of magnitude compared to bulk in multi-layered device which shows the efficient suppression of phonon propagation by using Pt-silicide/silicon hetero-junctions. - Highlights: • Silicide/silicon multi-layer structured is proposed for thermoelectric devices. • Electric and thermoelectric properties with the number of layer are investigated. • An increase of Seebeck coefficient is mainly attributed the Schottky barrier. • Phonon propagation is suppressed with the existence of Schottky barrier. • Thermal conductivity is reduced due to the suppression of phonon propagation

Thermal analysis of LEU modified Cintichem target irradiated in TRIGA reactor

International Nuclear Information System (INIS)

Catana, A; Toma, C.

2009-01-01

Actions conceived during last years at international level for conversion of Molybdenum fabrication process from HEU to LEU targets utilization created opportunities for INR to get access to information and participating to international discussions under IAEA auspices. Concrete steps for developing fission Molybdenum technology were facilitated. Institute of Nuclear Research bringing together a number of conditions like suitable irradiation possibilities, direct communication between reactor and hot cell facility, handling capacity of high radioactive sources, and simultaneously the existence of an expanding internal market, decided to undertake the necessary steps in order to produce fission molybdenum. Over the course of last years of efforts in this direction we developed the steps for fission Molybdenum technology development based on modified Cintichem process in accordance with the Argonne National Laboratory proved methodology. Progress made by INR to heat transfer computations of annular target using is presented. An advanced thermal-hydraulic analysis was performed to estimate the heat removal capability for an enriched uranium (LEU) foil annular target irradiated in TRIGA reactor core. As a result, the present analysis provides an upper limit estimate of the LEU-foil and external target surface temperatures during irradiation in TRIGA 14 MW reactor. (authors)

Whole-core analysis by 13C NMR

International Nuclear Information System (INIS)

Vinegar, H.J.; Tutunjian, P.N.; Edelstein, W.A.; Roemer, P.B.

1991-01-01

This paper reports on a whole-core nuclear magnetic resonance (NMR) system that was used to obtain natural abundance 13 C spectra. The system enables rapid, nondestructive measurements of bulk volume of movable oil, aliphatic/aromatic ratio, oil viscosity, and organic vs. carbonate carbon. 13 C NMR can be used in cores where the 1 H NMR spectrum is too broad to resolve oil and water resonances separately. A 5 1/4-in. 13 C/ 1 H NMR coil was installed on a General Electric (GE) CSI-2T NMR imager/spectrometer. With a 4-in.-OD whole core, good 13 C signal/noise ratio (SNR) is obtained within minutes, while 1 H spectra are obtained in seconds. NMR measurements have been made of the 13 C and 1 H density of crude oils with a wide range of API gravities. For light- and medium-gravity oils, the 13 C and 1 H signal per unit volume is constant within about 3.5%. For heavy crudes, the 13 C and 1 H density measured by NMR is reduced by the shortening of spin-spin relaxation time. 13 C and 1 H NMR spin-lattice relaxation times were measured on a suite of Cannon viscosity standards, crude oils (4 to 60 degrees API), and alkanes (C 5 through C 16 ) with viscosities at 77 degrees F ranging from 0.5 cp to 2.5 x 10 7 cp. The 13 C and 1 H relaxation times show a similar correlation with viscosity from which oil viscosity can be estimated accurately for viscosities up to 100 cp. The 13 C surface relaxation rate for oils on water-wet rocks is very low. Nonproton decoupled 13 C NMR is shown to be insensitive to kerogen; thus, 13 C NMR measures only the movable hydrocarbon content of the cores. In carbonates, the 13 C spectrum also contains a carbonate powder pattern useful in quantifying inorganic carbon and distinguishing organic from carbonate carbon

Fuel cycle flexibility in Advanced Heavy Water Reactor (AHWR) with the use of Th-LEU fuel

International Nuclear Information System (INIS)

Thakur, A.; Singh, B.; Pushpam, N.P.; Bharti, V.; Kannan, U.; Krishnani, P.D.; Sinha, R.K.

2011-01-01

The Advanced Heavy Water Reactor (AHWR) is being designed for large scale commercial utilization of thorium (Th) and integrated technological demonstration of the thorium cycle in India. The AHWR is a 920 MW(th), vertical pressure tube type cooled by boiling light water and moderated by heavy water. Heat removal through natural circulation and on-line fuelling are some of the salient features of AHWR design. The physics design of AHWR offers considerable flexibility to accommodate different kinds of fuel cycles. Our recent efforts have been directed towards a case study for the use of Th-LEU fuel cycle in a once-through mode. The discharged Uranium from Th-LEU cycle has proliferation resistant characteristics. This paper gives the initial core, fuel cycle characteristics and online refueling strategy of Th-LEU fuel in AHWR. (author)

Gas cluster ion beam assisted NiPt germano-silicide formation on SiGe

Energy Technology Data Exchange (ETDEWEB)

Ozcan, Ahmet S., E-mail: asozcan@us.ibm.com [IBM Almaden Research Center, 650 Harry Road, San Jose, California 95120 (United States); Lavoie, Christian; Jordan-Sweet, Jean [IBM T. J. Watson Research Center, 1101 Kitchawan Road, Yorktown Heights, New York 10598 (United States); Alptekin, Emre; Zhu, Frank [IBM Semiconductor Research and Development Center, 2070 Route 52, Hopewell Junction, New York 12533 (United States); Leith, Allen; Pfeifer, Brian D.; LaRose, J. D.; Russell, N. M. [TEL Epion Inc., 900 Middlesex Turnpike, Bldg. 6, Billerica, Massachusetts 01821 (United States)

2016-04-21

We report the formation of very uniform and smooth Ni(Pt)Si on epitaxially grown SiGe using Si gas cluster ion beam treatment after metal-rich silicide formation. The gas cluster ion implantation process was optimized to infuse Si into the metal-rich silicide layer and lowered the NiSi nucleation temperature significantly according to in situ X-ray diffraction measurements. This novel method which leads to more uniform films can also be used to control silicide depth in ultra-shallow junctions, especially for high Ge containing devices, where silicidation is problematic as it leads to much rougher interfaces.

Transition from HEU to LEU fuel in Romania's 14-MW TRIGA reactor

International Nuclear Information System (INIS)

Bretscher, M.M.; Snelgrove, J.L.

1995-01-01

The 14-MW TRIGA steady state reactor (SSR) located in Pitesti, Romania, first went critical in the fall of 1979. Initially, the core configuration for full power operation used 29 fuel clusters each containing a 5 x 5 square array of HEU U (10 wt% - ZrH - Er 2.8 wt%) fuel-moderator rods (1.295 cm o.d.) clad in Incoloy. With a total inventory of 35 HEU fuel clusters, burnup, considerations required a gradual expansion of the core from 29 to 32 and finally to 35 clusters before the reactor was shut down because of insufficient excess reactivity. At this time each of the original 29 fuel clusters had an average 235 U burnup in the range from 50 to 62%. Because of the U.S. policy regarding the export of highly enriched uranium, fresh HEU TRIGA replacement fuel is not available. After a number of safety-related measurements, the SSR is expected to resume full power operation in the near future using a mixed core containing five LEU TRIGA clusters of the same geometry as the original fuel but with fuel-moderator rods containing 45 wt% U (19.7% 235 U enrichment) and 1.1 wt% Er. Rods for 14 additional LEU fuel clusters will be fabricated by General Atomics. In support of the SSR mixed core operation numerous neutronic calculations have been performed. This paper presents some of the results of those calculations. (author)

NMOS contact resistance reduction with selenium implant into NiPt silicide

Science.gov (United States)

Rao, K. V.; Khaja, F. A.; Ni, C. N.; Muthukrishnan, S.; Darlark, A.; Lei, J.; Peidous, I.; Brand, A.; Henry, T.; Variam, N.; Erokhin, Y.

2012-11-01

A 25% reduction in NMOS contact resistance (Rc) was achieved by Selenium implantation into NiPt silicide film in VIISta Trident high-current single-wafer implanter. The Trident implanter is designed for shallow high-dose implants with high beam currents to maintain high throughput (for low CoO), with improved micro-uniformity and no energy contamination. The integration of Se implant was realized using a test chip dedicated to investigating silicide/junction related electrical properties and testable after silicidation. The silicide module processes were optimized, including the pre-clean (prior to RF PVD NiPt dep) and pre- and post-implant anneals. A 270°C soak anneal was used for RTP1, whereas a msec laser anneal was employed for RTP2 with sufficient process window (800-850°C), while maintaining excellent junction characteristics without Rs degradation.

Technology CAD of silicided Schottky barrier MOSFET for elevated source-drain engineering

International Nuclear Information System (INIS)

Saha, A.R.; Chattopadhyay, S.; Bose, C.; Maiti, C.K.

2005-01-01

Technology CAD has been used to study the performance of a silicided Schottky barrier (SB) MOSFET with gate, source and drain contacts realized with nickel-silicide. Elevated source-drain structures have been used towards the S/D engineering of CMOS devices. A full process-to-device simulation has been employed to predict the performance of sub-micron SB n-MOSFETs for the first time. A model for the diffusion and alloy growth kinetics has been incorporated in SILVACO-ATLAS and ATHENA to explore the processing and design parameter space for the Ni-silicided MOSFETs. The temperature and concentration dependent diffusion model for NiSi have been developed and necessary material parameters for nickel-silicide and epitaxial-Si have been incorporated through the C-interpreter function. Two-dimensional (2D) process-to-device simulations have also been used to study the dc and ac (RF) performance of silicided Schottky barrier (SB) n-MOSFETs. The extracted sheet resistivity, as a function of annealing temperature of the silicided S/D contacts, is found to be lower than the conventional contacts currently in use. It is also shown that the Technology CAD has the full capability to predict the possible dc and ac performance enhancement of a MOSFET with elevated S/D structures. While the simulated dc performance shows a clear enhancement, the RF analyses show no performance degradation in the cut-off frequency/propagation delay and also improve the ac performance due to the incorporation of silicide contacts in the S/D region

Technology CAD of silicided Schottky barrier MOSFET for elevated source-drain engineering

Energy Technology Data Exchange (ETDEWEB)

Saha, A.R. [Department of Electronics and ECE, IIT, Kharagpur 721302 (India)]. E-mail: ars.iitkgp@gmail.com; Chattopadhyay, S. [Department of Electronics and ECE, IIT, Kharagpur 721302 (India); School of Electrical, Electronics and Computer Engineering, University of Newcastle, Newcastle upon Tyne (United Kingdom); Bose, C. [Department of Electronics and Telecommunication Engineering, Jadavpur University, Calcutta 700032 (India); Maiti, C.K. [Department of Electronics and ECE, IIT, Kharagpur 721302 (India)

2005-12-05

Technology CAD has been used to study the performance of a silicided Schottky barrier (SB) MOSFET with gate, source and drain contacts realized with nickel-silicide. Elevated source-drain structures have been used towards the S/D engineering of CMOS devices. A full process-to-device simulation has been employed to predict the performance of sub-micron SB n-MOSFETs for the first time. A model for the diffusion and alloy growth kinetics has been incorporated in SILVACO-ATLAS and ATHENA to explore the processing and design parameter space for the Ni-silicided MOSFETs. The temperature and concentration dependent diffusion model for NiSi have been developed and necessary material parameters for nickel-silicide and epitaxial-Si have been incorporated through the C-interpreter function. Two-dimensional (2D) process-to-device simulations have also been used to study the dc and ac (RF) performance of silicided Schottky barrier (SB) n-MOSFETs. The extracted sheet resistivity, as a function of annealing temperature of the silicided S/D contacts, is found to be lower than the conventional contacts currently in use. It is also shown that the Technology CAD has the full capability to predict the possible dc and ac performance enhancement of a MOSFET with elevated S/D structures. While the simulated dc performance shows a clear enhancement, the RF analyses show no performance degradation in the cut-off frequency/propagation delay and also improve the ac performance due to the incorporation of silicide contacts in the S/D region.

Structural and electronic properties of rare-earth silicide thin films at Si(111)

Energy Technology Data Exchange (ETDEWEB)

Dues, Christof; Schmidt, Wolf Gero; Sanna, Simone [Lehrstuhl fuer Theoretische Physik, Universitaet Paderborn (Germany)

2016-07-01

Rare-earth (RE) silicides thin films on silicon surfaces are currently of high interest. They grow nearly defect-free because of the small lattice mismatch, and exhibit very low Schottky-barriers on n-type silicon. They even give rise to the self-organized formation of RE silicide nanowires on the Si(001) and vicinal surfaces. Depending on the amount of deposited RE atoms, a plethora of reconstructions are observed for the RE silicide. While one monolayer leads to the formation of a 1 x 1-reconstruction, several monolayer thick silicides crystallize in a √(3) x √(3) R30 {sup circle} superstructure. Submonolayer RE deposition leads to different periodicities. In this work we investigate the formation of RE silicides thin films on Si(111) within the density functional theory. The energetically favored adsorption site for RE adatoms is determined calculating the potential energy surface. As prototypical RE, Dysprosium is used. Additional calculations are performed for silicides formed by different RE elements. We calculate structural properties, electronic band structures and compare measured and simulated STM images. We consider different terminations for the 5 x 2 reconstruction occurring in the submonolayer regime and investigate their stability by means of ab initio thermodynamics. The same method is employed to predict the stable silicide structure as a function of the deposited RE atoms.

Silicide/Silicon Heterointerfaces, Reaction Kinetics and Ultra-short Channel Devices

Science.gov (United States)

Tang, Wei

Nickel silicide is one of the electrical contact materials widely used on very large scale integration (VLSI) of Si devices in microelectronic industry. This is because the silicide/silicon interface can be formed in a highly controlled manner to ensure reproducibility of optimal structural and electrical properties of the metal-Si contacts. These advantages can be inherited to Si nanowire (NW) field-effect transistors (FET) device. Due to the technological importance of nickel silicides, fundamental materials science of nickel silicides formation (Ni-Si reaction), especially in nanoscale, has raised wide interest and stimulate new insights and understandings. In this dissertation, in-situ transmission electron microscopy (TEM) in combination with FET device characterization will be demonstrated as useful tools in nano-device fabrication as well as in gaining insights into the process of nickel silicide formation. The shortest transistor channel length (17 nm) fabricated on a vapor-liquid-solid (VLS) grown silicon nanowire (NW) has been demonstrated by controlled reaction with Ni leads on an in-situ transmission electron microscope (TEM) heating stage at a moderate temperature of 400 ºC. NiSi2 is the leading phase, and the silicide-silicon interface is an atomically sharp type-A interface. At such channel lengths, high maximum on-currents of 890 (microA/microm) and a maximum transconductance of 430 (microS/microm) were obtained, which pushes forward the performance of bottom-up Si NW Schottky barrier field-effect transistors (SB-FETs). Through accurate control over the silicidation reaction, we provide a systematic study of channel length dependent carrier transport in a large number of SB-FETs with channel lengths in the range of (17 nm -- 3.6 microm). Our device results corroborate with our transport simulations and reveal a characteristic type of short channel effects in SB-FETs, both in on- and off-state, which is different from that in conventional MOSFETs

Specialists' meeting on role of fission products in whole core accidents

Energy Technology Data Exchange (ETDEWEB)

NONE

1977-07-01

Safety of nuclear reactors has been a central concern of the nuclear energy industry from the very beginning. This concern, and the resultant excellence of design, fabrication, and operation, aided by extensive engineered safety features, has given nuclear energy its superior record of protection of the environment and of the public health and safety. With respect to the fast reactor, it was recognized early in the program that there exists a theoretical possibility of a core compaction leading to significant energy release. The considerations of fission product effects are primarily on of the main concerns in evaluation of safety issues. Since fission products have the potential for dispersing fuel from the core region and thereby producing reactor shutdown, knowledge of their effects can contribute to demonstrating that there is a low probability producing whole-core involvement. Similarly, knowledge of fission product effects can contribute to demonstrating that there is a low probability of a whole-core disruptive accident leading to sufficient energy release to challenge the containment capability.

Specialists' meeting on role of fission products in whole core accidents

International Nuclear Information System (INIS)

1977-01-01

Safety of nuclear reactors has been a central concern of the nuclear energy industry from the very beginning. This concern, and the resultant excellence of design, fabrication, and operation, aided by extensive engineered safety features, has given nuclear energy its superior record of protection of the environment and of the public health and safety. With respect to the fast reactor, it was recognized early in the program that there exists a theoretical possibility of a core compaction leading to significant energy release. The considerations of fission product effects are primarily on of the main concerns in evaluation of safety issues. Since fission products have the potential for dispersing fuel from the core region and thereby producing reactor shutdown, knowledge of their effects can contribute to demonstrating that there is a low probability producing whole-core involvement. Similarly, knowledge of fission product effects can contribute to demonstrating that there is a low probability of a whole-core disruptive accident leading to sufficient energy release to challenge the containment capability

Reactivity accident analysis in MTR cores

International Nuclear Information System (INIS)

Waldman, R.M.; Vertullo, A.C.

1987-01-01

The purpose of the present work is the analysis of reactivity transients in MTR cores with LEU and HEU fuels. The analysis includes the following aspects: the phenomenology of the principal events of the accident that takes place, when a reactivity of more than 1$ is inserted in a critical core in less than 1 second. The description of the accident that happened in the RA-2 critical facility in September 1983. The evaluation of the accident from different points of view: a) Theoretical and qualitative analysis; b) Paret Code calculations; c) Comparison with Spert I and Cabri experiments and with post-accident inspections. Differences between LEU and HEU RA-2 cores. (Author)

Quantitative EPMA of Nano-Phase Iron-Silicides in Apollo 16 Lunar Regolith

Science.gov (United States)

Gopon, P.; Fournelle, J.; Valley, J. W.; Pinard, P. T.; Sobol, P.; Horn, W.; Spicuzza, M.; Llovet, X.; Richter, S.

2013-12-01

Until recently, quantitative EPMA of phases under a few microns in size has been extremely difficult. In order to achieve analytical volumes to analyze sub-micron features, accelerating voltages between 5 and 8 keV need to be used. At these voltages the normally used K X-ray transitions (of higher Z elements) are no longer excited, and we must rely of outer shell transitions (L and M). These outer shell transitions are difficult to use for quantitative EPMA because they are strongly affected by different bonding environments, the error associated with their mass attenuation coefficients (MAC), and their proximity to absorption edges. These problems are especially prevalent for the transition metals, because of the unfilled M5 electron shell where the Lα transition originates. Previous studies have tried to overcome these limitations by using standards that almost exactly matched their unknowns. This, however, is cumbersome and requires accurate knowledge of the composition of your sample beforehand, as well as an exorbitant number of well characterized standards. Using a 5 keV electron beam and utilizing non-standard X-ray transitions (Ll) for the transition metals, we are able to conduct accurate quantitative analyses of phases down to ~300nm. The Ll transition in the transition metals behaves more like a core-state transition, and unlike the Lα/β lines, is unaffected by bonding effects and does not lie near an absorption edge. This allows for quantitative analysis using standards do not have to exactly match the unknown. In our case pure metal standards were used for all elements except phosphorus. We present here data on iron-silicides in two Apollo 16 regolith grains. These plagioclase grains (A6-7 and A6-8) were collected between North and South Ray Craters, in the lunar highlands, and thus are associated with one or more large impact events. We report the presence of carbon, nickel, and phosphorus (in order of abundance) in these iron-silicide phases

Silicide Schottky Contacts to Silicon: Screened Pinning at Defect Levels

Energy Technology Data Exchange (ETDEWEB)

Drummond, T.J.

1999-03-11

Silicide Schottky contacts can be as large as 0.955 eV (E{sub v} + 0.165 eV) on n-type silicon and as large as 1.05 eV (E{sub c} {minus} 0.07 eV) on p-type silicon. Current models of Schottky barrier formation do not provide a satisfactory explanation of occurrence of this wide variation. A model for understanding Schottky contacts via screened pinning at defect levels is presented. In the present paper it is shown that most transition metal silicides are pinned approximately 0.48 eV above the valence band by interstitial Si clusters. Rare earth disilicides pin close to the divacancy acceptor level 0.41 eV below the conduction band edge while high work function silicides of Ir and Pt pin close to the divacancy donor level 0.21 eV above the valence band edge. Selection of a particular defect pinning level depends strongly on the relative positions of the silicide work function and the defect energy level on an absolute energy scale.

Distinguishing Isomeric Peptides: The Unimolecular Reactivity and Structures of (LeuPro)M+ and (ProLeu)M+ (M = Alkali Metal).

Science.gov (United States)

Jami-Alahmadi, Yasaman; Linford, Bryan D; Fridgen, Travis D

2016-12-29

The unimolecular chemistries and structures of gas-phase (ProLeu)M + and (LeuPro)M + complexes when M = Li, Na, Rb, and Cs have been explored using a combination of SORI-CID, IRMPD spectroscopy, and computational methods. CID of both (LeuPro)M + and (ProLeu)M + showed identical fragmentation pathways and could not be differentiated. Two of the fragmentation routes of both peptides produced ions at the same nominal mass as (Pro)M + and (Leu)M + , respectively. For the litiated peptides, experiments revealed identical IRMPD spectra for each of the m/z 122 and 138 ions coming from both peptides. Comparison with computed IR spectra identified them as the (Pro)Li + and (Leu)Li + , and it is concluded that both zwitterionic and canonical forms of (Pro)Li + exist in the ion population from CID of both (ProLeu)Li + and (LeuPro)Li + . The two isomeric peptide complexes could be distinguished using IRMPD spectroscopy in both the fingerprint and the CH/NH/OH regions. The computed IR spectra for the lowest energy structures of each charge solvated complexes are consistent with the IRMPD spectra in both regions for all metal cation complexes. Through comparison between the experimental spectra, it was determined that in lithiated and sodiated ProLeu, metal cation is bound to both carbonyl oxygens and the amine nitrogen. In contrast, the larger metal cations are bound to the two carbonyls, while the amine nitrogen is hydrogen bonded to the amide hydrogen. In the lithiated and sodiated LeuPro complexes, the metal cation is bound to the amide carbonyl and the amine nitrogen while the amine nitrogen is hydrogen bonded to the carboxylic acid carbonyl. However, there is no hydrogen bond in the rubidiated and cesiated complexes; the metal cation is bound to both carbonyl oxygens and the amine nitrogen. Details of the position of the carboxylic acid C═O stretch were especially informative in the spectroscopic confirmation of the lowest energy computed structures.

A comparison of the radiological consequences of a HEU and LEU fueled research reactor

International Nuclear Information System (INIS)

Kollas, J.G.

1985-01-01

An analysis of the design basis accident radiological consequences of the HEU and LEU fueled Greek Research Reactor is presented. Doses and individual cancer risk from exposure to the passing radioactive cloud are estimated up to a distance of 20 km from the reactor site. Collective exposure and latent health effects are estimated for the total Athens area of 3081000 inhabitants. The results indicate that the plutonium isotopes buildup in the LEU fuel does not increase appreciably the consequences in respect to the HEU fueled reactor. The plutonium impact concerns mainly bone effects and secondly lung and whole body effects. The contribution to the limiting thyroid dose and the corresponding thyroid effects is insignificant. (author)

Calculations in support of the MNR core conversion

International Nuclear Information System (INIS)

Day, S.E.; Butler, M.P.; Garland, Wm. J.

2002-01-01

Calculations and results in support of the HEU to LEU fuel conversion for the McMaster Nuclear Reactor are described. Static reactor physics studies were used to determine local and global power distributions; facilitating the definition of a Reference Core configuration for mixed HEU-LEU and complete LEU loadings. Fission product inventory calculations were used to compare the two fuel enrichments from a radiological hazard point of view. Thermalhydraulic models were created and analyzed to determine steady-state temperature distributions and safety margins, and used as a scoping tool the in development of a full core thermalhydraulic model. The behaviour of the two enrichment fuels was investigated in the context of a protected startup transient. The simulation results support the conclusion that the LEU fuel behaves in much the same way as the HEU fuel, which it is replacing. The conversion results in no new safety issues or significant changes in safety parameters. (author)

Kinetics of nickel silicide growth in silicon nanowires: From linear to square root growth

International Nuclear Information System (INIS)

Yaish, Y. E.; Beregovsky, M.; Katsman, A.; Cohen, G. M.

2011-01-01

The common practice for nickel silicide formation in silicon nanowires (SiNWs) relies on axial growth of silicide along the wire that is initiated from nickel reservoirs at the source and drain contacts. In the present work the silicide intrusions were studied for various parameters including wire diameter (25-50 nm), annealing time (15-120 s), annealing temperature (300-440 deg. C), and the quality of the initial Ni/Si interface. The silicide formation was investigated by high-resolution scanning electron microscopy, high-resolution transmission electron microscopy (TEM), and atomic force microscopy. The main part of the intrusion formed at 420 deg. C consists of monosilicide NiSi, as was confirmed by energy dispersive spectroscopy STEM, selected area diffraction TEM, and electrical resistance measurements of fully silicided SiNWs. The kinetics of nickel silicide axial growth in the SiNWs was analyzed in the framework of a diffusion model through constrictions. The model calculates the time dependence of the intrusion length, L, and predicts crossover from linear to square root time dependency for different wire parameters, as confirmed by the experimental data.

HEU and Leu FueL Shielding Comparative Study Applied for Spent Fuel Transport

International Nuclear Information System (INIS)

Margeanu, C.A.; Margeanu, S.; Barbos, D.

2009-01-01

INR Pitesti owns and operates a TRIGA dual-core Research Reactor for material testing, power reactor fuel and nuclear safety studies. The dual core concept involves the operation of a 14 MW TRIGA steady-state, high flux research and material testing reactor at one end of a large pool, and the independent operation of an annular-core pulsing reactor (TRIGA-ACPR) at the other end of the pool. The steady-state reactor is mostly used for long term testing of power reactor fuel components (pellets, pins, subassemblies and fuel assemblies) followed by post-irradiation examination. Following the general trend to replace the He fuel type (High Enriched Uranium) by Leu fuel type (Low Enriched Uranium), in the light of international agreements between IAEA and the states using He fuel in their nuclear reactors, Inr Past's have been accomplished the TRIGA research reactor core full conversion on May 2006. The He fuel repatriation in US in the frame of Foreign Research Reactor Spent Nuclear Fuel Return Programme effectively started in 1999, the final stage being achieved in summer of 2008. Taking into account for the possible impact on the human and environment, in all activities associated to nuclear fuel cycle, the spent fuel or radioactive waste characteristics must be well known. Shielding calculations basic tasks consist in radiation doses calculation, in order to prevent any risks both for personnel protection and impact on the environment during the spent fuel manipulation, transport and storage. The paper is a comparative study of Leu and He fuel utilization effects for the shielding analysis during spent fuel transport. A comparison against the measured data for He spent fuel, available from the last stage of the spent fuel repatriation, is presented. All the geometrical and material data related on the spent fuel shipping cask were considered according to the Nac-Lt Cask approved model. The shielding analysis estimates radiation doses to shipping cask wall surface

Neutronics Study on LEU Nuclear Thermal Rocket Fuel Options

Energy Technology Data Exchange (ETDEWEB)

Venneri, Paolo; Kim, Yong Hee [KAIST, Daejeon (Korea, Republic of); Howe, Steven [CSNR, Idaho (United States)

2014-10-15

This has resulted in a non-trivial simplification of the tasks needed to develop such an engine and the quick initial development of the concept. There are, however, a series of key core-design choices that are currently under scrutiny in the field that have to be resolved in order for the LEU-NTR to be fully developed. The most important of these is the choice of fuel: carbide composite or tungsten cermet. This study presents a first comparison of the two fuel types specifically in the neutronic application to the LEU-NTR, keeping in mind the unique neutronic environment and the system requirements of the system. The scope of the study itself is limited to a neutronics study of the two fuels and only a cursory overview of the material properties of the fuels themselves... The results of this study have led to two major conclusions. First of all is that the carbide composite fuel is, from a neutronics standpoint, a much better fuel. It has a low absorption cross-section, is inherently a strong moderator, is able to achieve a higher reactivity using smaller amounts of fissile material, and can potentially enable a smaller reactor. Second is that despite its neutronic difficulties (high absorption, inferior moderating abilities, and lower k-infinity values) the tungsten cermet fuel is still able to perform satisfactorily in an LEU-NTR, largely due to its ability to have an extremely high fuel loading.

Influence of IR-laser irradiation on α-SiC-chromium silicides ceramics

International Nuclear Information System (INIS)

Vlasova, M.; Marquez Aguilar, P.A.; Resendiz-Gonzalez, M.C.; Kakazey, M.; Bykov, A.; Gonzalez Morales, I.

2005-01-01

This project investigated the influence of IR-laser irradiation (λ = 1064 nm, P = 240 mW) on composite ceramics SiC-chromium silicides (CrSi 2 , CrSi, Cr 5 Si 3 ) by methods of X-ray diffraction, electron microscopy, atomic force microscopy, and X-ray microanalysis. Samples were irradiated in air. It was established that a surface temperature of 1990 K was required to melt chromium silicides, evaporate silicon from SiC, oxidize chromium silicides, and enrich superficial layer by carbon and chromium oxide

Prediction of barrier inhomogeneities and carrier transport in Ni-silicided Schottky diode

International Nuclear Information System (INIS)

Saha, A.R.; Dimitriu, C.B.; Horsfall, A.B.; Chattopadhyay, S.; Wright, N.G.; O'Neill, A.G.; Maiti, C.K.

2006-01-01

Based on Quantum Mechanical (QM) carrier transport and the effects of interface states, a theoretical model has been developed to predict the anomalous current-voltage (I-V) characteristics of a non-ideal Ni-silicided Schottky diode at low temperatures. Physical parameters such as barrier height, ideality factor, series resistance and effective Richardson constant of a silicided Schottky diode were extracted from forward I-V characteristics and are subsequently used for the simulation of both forward and reverse I-V characteristics using a QM transport model in which the effects of interface state and bias dependent barrier reduction are incorporated. The present analysis indicates that the effects of barrier inhomogeneity caused by incomplete silicide formation at the junction and the interface states may change the conventional current transport process, leading to anomalous forward and reverse I-V characteristics for the Ni-silicided Schottky diode

Far-infrared spectroscopy of thermally annealed tungsten silicide films

International Nuclear Information System (INIS)

Amiotti, M.; Borghesi, A.; Guizzetti, G.; Nava, F.; Santoro, G.

1991-01-01

The far-infrared transmittance spectrum of tungsten silicide has been observed for the first time. WSi 2 polycrystalline films were prepared by coevaporation and chemical-vapour deposition on silicon wafers, and subsequently thermally annealed at different temperatures. The observed structures are interpreted, on the basis of the symmetry properties of the crystal, such as infrared-active vibrational modes. Moreover, the marked lineshape dependence on annealing temperature enables this technique to analyse the formation of the solid silicide phases

TRIGA high wt -% LEU fuel development program. Final report

International Nuclear Information System (INIS)

West, G.B.

1980-07-01

The principal purpose of this work was to investigate the characteristics of TRIGA fuel where the contained U-235 was in a relatively high weight percent (wt %) of LEU (low enriched uranium - enrichment of less than 20%) rather than a relatively low weight percent of HEU (high enriched uranium). Fuel with up to 45 wt % U was fabricated and found to be acceptable after metallurgical examinations, fission product retention tests and physical property examinations. Design and safety analysis studies also indicated acceptable prompt negative temperature coefficient and core lifetime characteristics for these fuels

Texture in thin film silicides and germanides: A review

International Nuclear Information System (INIS)

De Schutter, B.; De Keyser, K.; Detavernier, C.; Lavoie, C.

2016-01-01

Silicides and germanides are compounds consisting of a metal and silicon or germanium. In the microelectronics industry, silicides are the material of choice for contacting silicon based devices (over the years, CoSi_2, C54-TiSi_2, and NiSi have been adopted), while germanides are considered as a top candidate for contacting future germanium based electronics. Since also strain engineering through the use of Si_1_−_xGe_x in the source/drain/gate regions of MOSFET devices is an important technique for improving device characteristics in modern Si-based microelectronics industry, a profound understanding of the formation of silicide/germanide contacts to silicon and germanium is of utmost importance. The crystallographic texture of these films, which is defined as the statistical distribution of the orientation of the grains in the film, has been the subject of scientific studies since the 1970s. Different types of texture like epitaxy, axiotaxy, fiber, or combinations thereof have been observed in such films. In recent years, it has become increasingly clear that film texture can have a profound influence on the formation and stability of silicide/germanide contacts, as it controls the type and orientation of grain boundaries (affecting diffusion and agglomeration) and the interface energy (affecting nucleation during the solid-state reaction). Furthermore, the texture also has an impact on the electrical characteristics of the contact, as the orientation and size of individual grains influences functional properties such as contact resistance and sheet resistance and will induce local variations in strain and Schottky barrier height. This review aims to give a comprehensive overview of the scientific work that has been published in the field of texture studies on thin film silicide/germanide contacts.

Texture in thin film silicides and germanides: A review

Science.gov (United States)

De Schutter, B.; De Keyser, K.; Lavoie, C.; Detavernier, C.

2016-09-01

Silicides and germanides are compounds consisting of a metal and silicon or germanium. In the microelectronics industry, silicides are the material of choice for contacting silicon based devices (over the years, CoSi2, C54-TiSi2, and NiSi have been adopted), while germanides are considered as a top candidate for contacting future germanium based electronics. Since also strain engineering through the use of Si1-xGex in the source/drain/gate regions of MOSFET devices is an important technique for improving device characteristics in modern Si-based microelectronics industry, a profound understanding of the formation of silicide/germanide contacts to silicon and germanium is of utmost importance. The crystallographic texture of these films, which is defined as the statistical distribution of the orientation of the grains in the film, has been the subject of scientific studies since the 1970s. Different types of texture like epitaxy, axiotaxy, fiber, or combinations thereof have been observed in such films. In recent years, it has become increasingly clear that film texture can have a profound influence on the formation and stability of silicide/germanide contacts, as it controls the type and orientation of grain boundaries (affecting diffusion and agglomeration) and the interface energy (affecting nucleation during the solid-state reaction). Furthermore, the texture also has an impact on the electrical characteristics of the contact, as the orientation and size of individual grains influences functional properties such as contact resistance and sheet resistance and will induce local variations in strain and Schottky barrier height. This review aims to give a comprehensive overview of the scientific work that has been published in the field of texture studies on thin film silicide/germanide contacts.

Texture in thin film silicides and germanides: A review

Energy Technology Data Exchange (ETDEWEB)

De Schutter, B., E-mail: bob.deschutter@ugent.be; De Keyser, K.; Detavernier, C. [Department of Solid State Sciences, Ghent University, Ghent (Belgium); Lavoie, C. [IBM Research Division, T.J. Watson Research Center, P.O. Box 218, Yorktown Heights, New York 10598 (United States)

2016-09-15

Silicides and germanides are compounds consisting of a metal and silicon or germanium. In the microelectronics industry, silicides are the material of choice for contacting silicon based devices (over the years, CoSi{sub 2}, C54-TiSi{sub 2}, and NiSi have been adopted), while germanides are considered as a top candidate for contacting future germanium based electronics. Since also strain engineering through the use of Si{sub 1−x}Ge{sub x} in the source/drain/gate regions of MOSFET devices is an important technique for improving device characteristics in modern Si-based microelectronics industry, a profound understanding of the formation of silicide/germanide contacts to silicon and germanium is of utmost importance. The crystallographic texture of these films, which is defined as the statistical distribution of the orientation of the grains in the film, has been the subject of scientific studies since the 1970s. Different types of texture like epitaxy, axiotaxy, fiber, or combinations thereof have been observed in such films. In recent years, it has become increasingly clear that film texture can have a profound influence on the formation and stability of silicide/germanide contacts, as it controls the type and orientation of grain boundaries (affecting diffusion and agglomeration) and the interface energy (affecting nucleation during the solid-state reaction). Furthermore, the texture also has an impact on the electrical characteristics of the contact, as the orientation and size of individual grains influences functional properties such as contact resistance and sheet resistance and will induce local variations in strain and Schottky barrier height. This review aims to give a comprehensive overview of the scientific work that has been published in the field of texture studies on thin film silicide/germanide contacts.

RERTR progress in Mo-99 production from LEU

Energy Technology Data Exchange (ETDEWEB)

Vandegrift, G.F.; Conner, C.; Aase, S.; Bakel, A.; Bowers, D.; Freiberg, E.; Gelis, A.; Quigley, K.J.; Snelgrove, J.L. [Argonne National Laboratory 9700 S. Cass Avenue, Argonne, IL (United States)

2002-07-01

The ANL RERTR program is performing R and D supporting conversion of {sup 99}Mo production from HEU to LEU targets. Irradiation and processing of LEU targets were demonstrated at the Argentine Ezeiza Atomic Center. Target irradiation and disassembly were flawless, but the processing is not fully developed. In addition to preparing for, assisting in, and analyzing results of the demonstration, we performed other R and D related to LEU conversion: (1) designing a prototype production dissolver for digesting irradiated LEU foils in alkaline solutions and developing means to simplify digestion, (2) modifying ion-exchange columns used in the CNEA recovery and purification of {sup 99}Mo to deal with the lower volumes generated from LEU-foil digestion, (3) measuring the performance of new inorganic sorbents that outperform alumina for recovering Mo(VI) from nitric acid solutions containing high concentrations of uranium nitrate, and (4) developing means to facilitate the concentration and calcination of waste nitric-acid/LEU-nitrate solutions from {sup 99} Mo production. (author)

Vver-1000 Mox core computational benchmark

International Nuclear Information System (INIS)

2006-01-01

The NEA Nuclear Science Committee has established an Expert Group that deals with the status and trends of reactor physics, fuel performance and fuel cycle issues related to disposing of weapons-grade plutonium in mixed-oxide fuel. The objectives of the group are to provide NEA member countries with up-to-date information on, and to develop consensus regarding, core and fuel cycle issues associated with burning weapons-grade plutonium in thermal water reactors (PWR, BWR, VVER-1000, CANDU) and fast reactors (BN-600). These issues concern core physics, fuel performance and reliability, and the capability and flexibility of thermal water reactors and fast reactors to dispose of weapons-grade plutonium in standard fuel cycles. The activities of the NEA Expert Group on Reactor-based Plutonium Disposition are carried out in close co-operation (jointly, in most cases) with the NEA Working Party on Scientific Issues in Reactor Systems (WPRS). A prominent part of these activities include benchmark studies. At the time of preparation of this report, the following benchmarks were completed or in progress: VENUS-2 MOX Core Benchmarks: carried out jointly with the WPRS (formerly the WPPR) (completed); VVER-1000 LEU and MOX Benchmark (completed); KRITZ-2 Benchmarks: carried out jointly with the WPRS (formerly the WPPR) (completed); Hollow and Solid MOX Fuel Behaviour Benchmark (completed); PRIMO MOX Fuel Performance Benchmark (ongoing); VENUS-2 MOX-fuelled Reactor Dosimetry Calculation (ongoing); VVER-1000 In-core Self-powered Neutron Detector Calculational Benchmark (started); MOX Fuel Rod Behaviour in Fast Power Pulse Conditions (started); Benchmark on the VENUS Plutonium Recycling Experiments Configuration 7 (started). This report describes the detailed results of the benchmark investigating the physics of a whole VVER-1000 reactor core using two-thirds low-enriched uranium (LEU) and one-third MOX fuel. It contributes to the computer code certification process and to the

Development of Silicide Coating on Molybdenum Alloy Cladding

International Nuclear Information System (INIS)

Lim, Woojin; Ryu, Ho Jin

2015-01-01

The molybdenum alloy is considered as one of the accident tolerant fuel (ATF) cladding materials due to its high temperature mechanical properties. However, molybdenum has a weak oxidation resistance at elevated temperatures. To modify the oxidation resistance of molybdenum cladding, silicide coating on the cladding is considered. Molybdenum silicide layers are oxidized to SiO 2 in an oxidation atmosphere. The SiO 2 protective layer isolates the substrate from the oxidizing atmosphere. Pack cementation deposition technique is widely adopted for silicide coating for molybdenum alloys due to its simple procedure, homogeneous coating quality and chemical compatibility. In this study, the pack cementation method was conducted to develop molybdenum silicide layers on molybdenum alloys. It was found that the Mo 3 Si layer was deposited on substrate instead of MoSi 2 because of short holding time. It means that through the extension of holding time, MoSi 2 layer can be formed on molybdenum substrate to enhance the oxidation resistance of molybdenum. The accident tolerant fuel (ATF) concept is to delay the process following an accident by reducing the oxidation rate at high temperatures and to delay swelling and rupture of fuel claddings. The current research for Atf can be categorized into three groups: First, modification of existing zirconium-based alloy cladding by improving the high temperature oxidation resistance and strength. Second, replacing Zirconium based alloys with alternative metallic materials such as refractory elements with high temperature oxidation resistance and strength. Third, designing alternative fuel structures using ceramic and composite systems

Oxidation behavior of molybdenum silicides and their composites

International Nuclear Information System (INIS)

Natesan, K.; Deevi, S. C.

2000-01-01

A key materials issue associated with the future of high-temperature structural silicides is the resistance of these materials to oxidation at low temperatures. Oxidation tests were conducted on Mo-based silicides over a wide temperature range to evaluate the effects of alloy composition and temperature on the protective scaling characteristics and testing regime for the materials. The study included Mo 5 Si 3 alloys that contained several concentrations of B. In addition, oxidation characteristics of MoSi 2 -Si 3 N 4 composites that contained 20--80 vol.% Si 3 N 4 were evaluated at 500--1,400 C

Progress of Indonesia RERTR related programs

International Nuclear Information System (INIS)

Soentono, S.; Arbie, B.; Surpto, A.

2004-01-01

In Indonesia, there are two main activities covering study, research ad development which can be related to reduced enrichment for research and test reactors (RERTR) program. The first activity is the attempt to improve the G.A. Siwabessy multi-purpose reactor (RSG-GAS) performance following the successful RERTR program on the development of low-enriched uranium (LEU) with high uranium loading density. This activity consists of manufacturing technology development and fabrication of LEU fuel in the form Of U 3 Si 2 -Al with high U loading density being capable to reach high burn-up, study oil the core conversion of the RSG- GAS from using oxide LEU fuel with loading density of ∼3 gU/cc into using LEU silicide fuel of higher U loading density to improve the in-core fuel management, the fuel utilization, and the cycle length, while keeping the neutron flux in the irradiation facilities remaining satisfactory and the power of the reactor remaining the same without resulting any serious penalty on the reactor safety. The second RERTR related activity is the attempt to use LEU, instead of HEU, as the target or fission product 99 Mo production to supply 99 mTc for medical purposes. This second activity is expected to consist of experiments covering irradiation of various forms of LEU targets in the RSG-GAS, dissolution processes of the irradiated targets, separation and purification processes to meet the radiopharmaceutical requirements and recovery of 235 U from the waste as well as treatment of the emerged wastes. (author)

Reactor core conversion studies of Ghana: Research Reactor-1 and proposal for addition of safety rod

International Nuclear Information System (INIS)

Odoi, H.C.

2014-06-01

The inclusion of an additional safety rod in conjunction with a core conversion study of Ghana Research Reactor-1 (GHARR-1) was carried out using neutronics, thermal hydraulics and burnup codes. The study is based on a recommendation by Integrated Safety Assessment for Research Reactors (INSARP) mission to incorporate a safety rod to the reactor safety system as well as the need to replace the reactor fuel with LEU. Conversion from one fuel type to another requires a complete re-evaluation of the safety analysis. Changes to the reactivity worth, shutdown margin, power density and material properties must be taken into account, and appropriate modifications made. Neutronics analysis including burnup was studied followed by thermal hydraulics analyses which comprise steady state and transients. Four computer codes were used for the analysis; MCNP, REBUS, PLTEP and PARET. The neutronics analysis revealed that the LEU core must be operated at 34 Kw in order to attain the flux of 1.0E12 n/cm 2 .s as the nominal flux of the HEU core. The auxiliary safety rod placed at a modified irradiation site gives a better worth than the cadmium capsules. For core excess reactivity of 4 mk, 348 fuel pins would be appropriate for the GHARR-1 LEU core. Results indicate that flux level of 1.0E12 n/cm 2 .s in the inner irradiation channel will not be compromised, if the power of the LEU core is increased to 34 kW. The GHARR-1 core using LEU-U0 2 -12.5% fuel can be operated for 23 shim cycles, with cycles length 2.5 years, for over 57 years at the 17 kW power level. All 23 LEU cycles meet the ∼ 4.0 mk excess reactivity required at the beginning of cycle . For comparison, the MNSR HEU reference core can also be operated for 23 shim cycles, but with a cycle length of 2.0 years for just over 46 years at 15.0kW power level. It is observed that the GHARR-1 core with LEU UO 2 fuel enriched to 12.5% and a power level of 34 kW can be operated ∼25% longer than the current HEU core operated at

Microstructure and mechanical properties of metal/oxide and metal/silicide interfaces

International Nuclear Information System (INIS)

Shaw, L.; Miracle, D.; Abbaschian, R.

1995-01-01

Fracture energies of Al 2 O 3 /Nb interfaces and MoSi 2 /Nb interfaces with and without Al 2 O 3 coating were measured using sandwich-type chevron-notched specimens. The relations between the mechanical properties, microstructures, types of bonds at the interface and processing routes were explored. The fracture energy of the Al 2 O 3 /Nb interface was determined to be 9 J/m 2 and changed to 16 J/m 2 when Nb was pre-oxidized before the formation of the Al 2 O 3 /Nb interface. The fracture energy of the MoSi 2 /Nb interface could not be determined directly because of the formation of the interfacial compounds. However, the fracture energy at the MoSi 2 /Nb interfacial region was found to depend on the interfacial bond strength, roughness of interfaces and microstructure of interfacial compounds. The interfacial fracture energies of Al 2 O 3 with silicides, MoSi 2 , Nb 5 Si 3 , or (Nb, Mo)Si 2 were estimated to be about 16 J/m 2 , while the interfacial fracture energies between two silicides or between Nb and a silicide were larger than 34 J/m 2 . The measured fracture energies between two silicides or between Nb and a silicide were larger than 34 J/m 2 . The measured fracture energies of the various interfaces are discussed in terms of the interfacial microstructures and types of bonds at the interfaces

Analyses for inserting fresh LEU fuel assemblies instead of fresh HEU fuel assemblies in the Dalat Nuclear Research Reactor in Vietnam

International Nuclear Information System (INIS)

Hanan, N. A.; Deen, J.R.; Matos, J.E.

2005-01-01

Analyses were performed by the RERTR Program to replace 36 burned HEU (36%) fuel assemblies in the Dalat Nuclear Research Reactor in Vietnam with either 36 fresh fuel assemblies currently on-hand at the reactor or with LEU fuel assemblies to be procured. The study concludes that the current HEU (36%) WWR-M2 fuel assemblies can be replaced with LEU WWR-M2 fuel assemblies that are fully-qualified and have been commercially available since 2001 from the Novosibirsk Chemical Concentrates Plant in Russia. The current reactor configuration using re-shuffled HEU fuel began in June 2004 and is expected to allow normal operation until around August 2006. If 36 HEU assemblies each with 40.2 g 235 U are inserted without fuel shuffling over the next five operating cycles, the core could operate for an additional 10 years until June 2016. Alternatively, inserting 36 LEU fuel assemblies each containing 49.7 g 235 U without fuel shuffling over five operating cycles would allow normal operation for about 14 years from August 2006 until October 2020. The main reason for the longer service life of the LEU fuel is that its 235 U content is higher than the 235 U content needed simply to match the service life of the HEU fuel. Fast neutron fluxes in the experiment regions would be very nearly the same in both the HEU and LEU cores. Thermal neutron fluxes in the experiment regions would be lower by 1-5%, depending on the experiment type and location. (author)

Thermal stability of Ni-Pt-Ta alloy silicides on epi-Si{sub 1-x}C{sub x}

Energy Technology Data Exchange (ETDEWEB)

Yoo, Jung-Ho; Chang, Hyun-Jin [Department of Ceramic Engineering, Yonsei University, Seoul 120-749 (Korea, Republic of); Min, Byoung-Gi [Department of Ceramic Engineering, Yonsei University, Seoul 120-749 (Korea, Republic of); Jusung Engineering Co., Ltd., 49, Neungpyeong-ri, Opo-eup, Gwangju-Si, Kyunggi-do 464-892 (Korea, Republic of); Ko, Dae-Hong [Department of Ceramic Engineering, Yonsei University, Seoul 120-749 (Korea, Republic of)], E-mail: dhko@yonsei.ac.kr; Cho, Mann-Ho [Institute of Physics and Applied Physics, Yonsei University, Seoul 120-749 (Korea, Republic of); Sohn, Hyunchul [Department of Ceramic Engineering, Yonsei University, Seoul 120-749 (Korea, Republic of); Lee, Tae-Wan [Jusung Engineering Co., Ltd., 49, Neungpyeong-ri, Opo-eup, Gwangju-Si, Kyunggi-do 464-892 (Korea, Republic of)

2008-12-05

We investigated the silicide formation in Ni/epi-Si{sub 1-x}C{sub x} systems. Ni-Pt and Ni-Pt-Ta films were deposited on epi-Si{sub 1-x}C{sub x}/Si substrates by DC magnetron sputtering and processed at various temperatures. The sheet resistance of the silicide from the Ni alloy/epi-Si{sub 1-x}C{sub x} systems was maintained at low values compared to that from Ni/Si systems. By TEM and EDS analyses, we confirmed the presence of a Pt alloy layer at the top of the Ni-silicide layer. The stability of the silicide layer in the Ni alloy/epi-Si{sub 1-x}C{sub x} system is explained by not only the Pt rich layer on the top of the Ni-silicide layer, but also by the presence of a small amount of Pt in the Ni-silicide layer or at the grain boundaries. And both the thermal stability and the morphology of silicide were greatly improved by the addition of Ta in Ni-Pt films.

Irradiation of an uranium silicide prototype in RA-3 reactor

International Nuclear Information System (INIS)

Calabrese, R.; Estrik, G.; Notari, C.

1996-01-01

The factibility of irradiation of an uranium silicide (U 3 Si 2 ) prototype in the RA-3 reactor was studied. The standard RA-3 fuel element uses U 3 O 8 as fissible material. The enrichment of both standard and prototype is the same: 20% U 235 and also the frame geometry and number of plates is identical. The differences are in the plate dimensions and the fissile content which is higher in the prototype. The cooling conditions of the core allow the insertion of the prototype in any core position, even near the water trap, if the overall power is kept below 5Mw. Nevertheless, the recommendation was to begin irradiation near the periphery and later on move the prototype towards more central positions in order to increase the burnup rate. The prototype was effectively introduced in a peripheral position and the thermal fluxes were measured between plates with the foil activation technique. These were also evaluated with the fuel management codes and a reasonable agreement was found. (author). 5 refs., 3 figs., 3 tabs

Exploitation of a self-limiting process for reproducible formation of ultrathin Ni1-xPtx silicide films

International Nuclear Information System (INIS)

Zhang Zhen; Zhu Yu; Rossnagel, Steve; Murray, Conal; Jordan-Sweet, Jean; Yang, Bin; Gaudet, Simon; Desjardins, Patrick; Kellock, Andrew J.; Ozcan, Ahmet; Zhang Shili; Lavoie, Christian

2010-01-01

This letter reports on a process scheme to obtain highly reproducible Ni 1-x Pt x silicide films of 3-6 nm thickness formed on a Si(100) substrate. Such ultrathin silicide films are readily attained by sputter deposition of metal films, metal stripping in wet chemicals, and final silicidation by rapid thermal processing. This process sequence warrants an invariant amount of metal intermixed with Si in the substrate surface region independent of the initial metal thickness, thereby leading to a self-limiting formation of ultrathin silicide films. The crystallographic structure, thickness, uniformity, and morphological stability of the final silicide films depend sensitively on the initial Pt fraction.

Technical report: technical development on the silicide plate-type fuel experiment at nuclear safety research reactor

International Nuclear Information System (INIS)

Yanagisawa, Kazuaki; Soyama, Kazuhiko; Ichikawa, Hiroki

1991-08-01

According to a reduction of fuel enrichment from 45 w/o 235 U to 20 w/o, an aluminide plate-type fuel used currently in the domestic research and material testing reactors will be replaced by a silicide plate-type one. One of the major concern arisen from this alternation is to understand the fuel behavior under simulated reactivity initiated accident (RIA) conditions, this is strongly necessary from the safety and licensing point of view. The in-core RIA experiments are, therefore, carried out at Nuclear Safety Research Reactor (NSRR) in Japan Atomic Energy Research Institute (JAERI). The silicide plate-type fuel consisted of the ternary alloy of U-Al-Si as a meat with uranium density up to 4.8 g/cm 3 having thickness by 0.51 mm and the binary alloy of Al-3%Mg as a cladding by thickness of 0.38 mm. Comparison of the physical properties of this metallic plate fuel with the UO 2 -zircaloy fuel rod used conventionally in commercial light water reactors shows that the heat conductivity of the former is of the order of about 13 times greater than the latter, however the melting temperature is only one-half (1570degC). Prior to in-core RIA experiments, there were some difficulties lay in our technical path. This report summarized the technical achievements obtained through our four years work. (J.P.N.)

Improvement of Silicide Coating Method as Diffusion Barrier for U-Mo Dispersion Fuel

Energy Technology Data Exchange (ETDEWEB)

Nam, Ji Min; Kim, Sunghwan; Lee, Kyu Hong; Park, Jong Man [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2014-10-15

The excessive interaction between the U-Mo alloys and their surrounding Al matrix lead to excessive local swelling called 'pillowing'. For this reason, KAERI suggested several remedies such as alloying U-Mo with Ti, or Al matrix with Si. In addition, silicide or nitride coatings on the surface of U-Mo particles have also been proposed to hinder the growth of the interaction layer. In this study, centrifugally atomized U-Mo-Ti alloy powders were coated with silicide layers. The coating process was improved when compared to the previous coating in terms of the ball milling and heat treatment conditions. Subsequently, silicide coated U-Mo-Ti powders and pure aluminum powders were mixed and made into a compact for the annealing test. The compacts were annealed at 550 .deg. C for 2hr, and characterized using scanning electron microscopy (SEM) and energy dispersive x-ray spectroscopy (EDS). 1. Uniform, homogeneous, thickness controllable silicide layers were successfully coated on the surface of U-7wt%Mo-1wt%Ti powders. 2. U{sub 3}Si, U{sub 3}Si{sub 2} silicide layers formed on the surface of U-7wt%Mo-1wt%Ti powders, and were identified by XRD and EDS analyses.

Formation of silicides in a cavity applicator microwave system

International Nuclear Information System (INIS)

Thompson, D.C.; Kim, H.C.; Alford, T.L.; Mayer, J.W.

2003-01-01

Metal silicides of nickel and cobalt are formed in a cavity applicator microwave system with a magnetron power of 1200 W and a frequency of 2.45 GHz. X-ray diffraction, Rutherford backscattering spectrometry, and four-point-probe measurements are used to identify the silicide phase present and layer thicknesses. Additional processing confirmed that the products attained from heating by microwaves do not differ appreciably from those attained in heating by thermal processes. Materials properties are used to explain microwave power absorption and demonstrate how to tailor a robust process in which thin film reactions can be attained and specific products isolated

High-performance whole core Pin-by-Pin calculation based on EFEN-SP_3 method

International Nuclear Information System (INIS)

Yang Wen; Zheng Youqi; Wu Hongchun; Cao Liangzhi; Li Yunzhao

2014-01-01

The EFEN code for high-performance PWR whole core pin-by-pin calculation based on the EFEN-SP_3 method can be achieved by employing spatial parallelization based on MPI. To take advantage of the advanced computing and storage power, the entire problem spatial domain can be appropriately decomposed into sub-domains and the assigned to parallel CPUs to balance the computing load and minimize communication cost. Meanwhile, Red-Black Gauss-Seidel nodal sweeping scheme is employed to avoid the within-group iteration deterioration due to spatial parallelization. Numerical results based on whole core pin-by-pin problems designed according to commercial PWRs demonstrate the following conclusions: The EFEN code can provide results with acceptable accuracy; Communication period impacts neither the accuracy nor the parallel efficiency; Domain decomposition methods with smaller surface to volume ratio leads to greater parallel efficiency; A PWR whole core pin-by-pin calculation with a spatial mesh 289 × 289 × 218 and 4 energy groups could be completed about 900 s by using 125 CPUs, and its parallel efficiency is maintained at about 90%. (authors)

Development of production of {sup 99}Mo from LEU target

Energy Technology Data Exchange (ETDEWEB)

Adang, H G; Mutalib, A; Lubis, H [Radioisotope Production Centre, National Atomic Energy Agency, Kawasan Puspiptek, Serpong (Indonesia); and others

1998-10-01

{sup 99}TC, the most popular radioisotope in nuclear medicine, is daughter of {sup 99}Mo. {sup 99}Mo is produced in research reactor by irradiating of high enriched uranium (HEU). However, in recent year, strict regulation that has been implemented by USA DOE and NPT has led to the difficulty in getting HEU. Therefore, BATAN has tried to develop the production of {sup 99}Mo by using low enriched uranium (LEU). The research involves the use of LEU in the production of {sup 99}Mo. This research was started in 1994 by joint-research between BATAN and Argonne National Laboratory USA. This program is divided into three research groups. The first group emphasizes its research on fabrication of LEU foil that is going to be irradiated. The second group studies the irradiation`s aspects and physical characteristic of irradiated LEU foils. The third group studies the radiochemical separation process of fission product {sup 99}Mo from solution of irradiated LEU foils. There are five steps that are carried out in studying of radiochemical separation of {sup 99}Mo from irradiated LEU. First is designing a dissolver that is going to be used in dissolving of LEU foil and testing its reliability. Second is dissolving LEU in the new design dissolver. Third is evaluation the modified of Cintichem`s radiochemical separation process of {sup 99}Mo from LEU. Forth is modifying the Cintichem`s radiochemical separation process of {sup 99}Mo from the solution of irradiated LEU. And fifth is using the modified of Cintichem`s radiochemical separation process for separation {sup 99}Mo from solution of irradiated LEU. The first through the forth steps of experiments were already carried out and will be reported in this workshop, whereas the fifth step of experiment is going to be conducted in February 1998. (author)

Effects of Silicide Coating on the Interdiffusion between U-7Mo and Al

Energy Technology Data Exchange (ETDEWEB)

Nam, Ji Min; Kim, Ji Hyun; Kim, Sunghwan; Lee, Kyu Hong; Park, Jong Man; Jeong, Yong Jin; Kim, Ki Nam [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2015-05-15

The excessive interaction between the U-Mo alloys and their surrounding Al matrix lead to and excessive local swelling called 'pillowing'. For this reason, KAERI suggested several remedies such as alloying U-Mo with Ti, or Al matrix with Si. In addition, silicide, or nitride coatings on the surface of U-Mo particles have also been proposed to hinder the growth of interaction layer. In this study, centrifugally atomized U-7Mo alloy powders were coated with silicide layers at varying T (T = 900 and 1000 .deg. C) for 30 min, respectively. U-Mo alloy powder was blended with Si powders and subsequently heat-treated to form uranium-silicide coating layers on the surface of U-Mo alloy particles. For an annealing test, silicide-coated U-Mo alloy powders were made into a compact, and Al powders were used as a matrix. From EDS results, transformed uranium aluminide intermetallic compounds were mainly U(Al,Si)3. U(Al,Si)3 phase left the silicide coating layer behind, and formed inside of U-7Mo particles, as shown in Fig. 3(a) and (b). In the case of sample B, Al could not penetrate the silicide coating layer and the coating layers were remained constant, as shown in Fig. 3(c) and (d). From the results, we made a comparison between the compacts of sample A and B, and it was shown that Al can easily diffuse into unreacted Si and U{sub 3}Si{sub 5} mixed layer while U{sub 3}Si{sub 2} acted as a good diffusion barrier at 550 .deg. C though those layers had the same thickness.

Effects of Silicide Coating on the Interdiffusion between U-7Mo and Al

International Nuclear Information System (INIS)

Nam, Ji Min; Kim, Ji Hyun; Kim, Sunghwan; Lee, Kyu Hong; Park, Jong Man; Jeong, Yong Jin; Kim, Ki Nam

2015-01-01

The excessive interaction between the U-Mo alloys and their surrounding Al matrix lead to and excessive local swelling called 'pillowing'. For this reason, KAERI suggested several remedies such as alloying U-Mo with Ti, or Al matrix with Si. In addition, silicide, or nitride coatings on the surface of U-Mo particles have also been proposed to hinder the growth of interaction layer. In this study, centrifugally atomized U-7Mo alloy powders were coated with silicide layers at varying T (T = 900 and 1000 .deg. C) for 30 min, respectively. U-Mo alloy powder was blended with Si powders and subsequently heat-treated to form uranium-silicide coating layers on the surface of U-Mo alloy particles. For an annealing test, silicide-coated U-Mo alloy powders were made into a compact, and Al powders were used as a matrix. From EDS results, transformed uranium aluminide intermetallic compounds were mainly U(Al,Si)3. U(Al,Si)3 phase left the silicide coating layer behind, and formed inside of U-7Mo particles, as shown in Fig. 3(a) and (b). In the case of sample B, Al could not penetrate the silicide coating layer and the coating layers were remained constant, as shown in Fig. 3(c) and (d). From the results, we made a comparison between the compacts of sample A and B, and it was shown that Al can easily diffuse into unreacted Si and U 3 Si 5 mixed layer while U 3 Si 2 acted as a good diffusion barrier at 550 .deg. C though those layers had the same thickness

Nanoscale investigation of the interface situation of plated nickel and thermally formed nickel silicide for silicon solar cell metallization

Energy Technology Data Exchange (ETDEWEB)

Mondon, A., E-mail: andrew.mondon@ise.fraunhofer.de [Fraunhofer ISE, Heidenhofst. 2, D-79110 Freiburg (Germany); Wang, D. [Karlsruhe Nano Micro Facility (KNMF), H.-von-Helmholz-Platz 1, D-76344 Eggenstein-Leopoldshafen (Germany); Zuschlag, A. [Universität Konstanz FB Physik, Jacob-Burckhardt-Str. 27, D-78464 Konstanz (Germany); Bartsch, J.; Glatthaar, M.; Glunz, S.W. [Fraunhofer ISE, Heidenhofst. 2, D-79110 Freiburg (Germany)

2014-12-30

Highlights: • Adhesion of metallization of fully plated nickel–copper contacts on silicon solar cells can be achieved by formation of nickel silicide at the cost of degraded cell performance. • Understanding of silicide growth mechanisms and controlled growth may lead to high performance together with excellent adhesion. • Silicide formation is well known from CMOS production from PVD-Ni on flat surfaces. Yet the deposition methods and therefore layer characteristics and the surface topography are different for plated metallization. • TEM analysis is performed for differently processed samples. • A nickel silicide growth model is created for plated Ni on textured silicon solar cells. - Abstract: In the context of nickel silicide formation from plated nickel layers for solar cell metallization, there are several open questions regarding contact adhesion and electrical properties. Nanoscale characterization by transmission electron microscopy has been employed to support these investigations. Interfacial oxides and silicide phases were investigated on differently prepared samples by different analytical methods associated with transmission electron microscopy analysis. Processing variations included the pre-treatment of samples before nickel plating, the used plating solution and the thermal budget for the nickel–silicon solid-state reaction. It was shown that interface oxides of only few nm thickness on both silicon and nickel silicide are present on the samples, depending on the chosen process sequence, which have been shown to play an important role in adhesion of nickel on silicide in an earlier publication. From sample pretreatment variations, conclusions about the role of an interfacial oxide in silicide formation and its influence on phase formation were drawn. Such an oxide layer hinders silicide formation except for pinhole sites. This reduces the availability of Ni and causes a silicide with low Ni content to form. Without an interfacial oxide

Whole core transport calculation for the VHTR hexagonal core

International Nuclear Information System (INIS)

Cho, J. Y.; Kim, K. S.; Lee, C. C.; Joo, H. G.

2007-01-01

Recently, the DeCART code which performs the whole core calculation by coupling the radial MOC transport kernel with the axial nodal kernel has equipped a kernel to deal with the hexagonal geometry and applied to the VHTR hexagonal core to examine the accuracy and the computational efficiency of the implemented kernel. The implementation includes a modular ray tracing module based on the hexagonal assembly and a multi-group CMFD module to perform an efficient transport calculation. The requirements for the modular ray are: (1) the assembly based path linking and (2) the complete reflection capabilities. The first requirement is met by adjusting the azimuthal angle and the ray spacing for the modular ray to construct a core ray by the path linking. The second requirement is met by expanding the constructed azimuthal angle in the range of [0,30 degree] to the remained range to reflect completely at the core boundaries. The considered reflecting surface angles for the complete reflection are 30n's (n=1,2,1,12). The CMFD module performs the equivalent diffusion calculation to the radial MOC transport calculation based on the homogenized structure units. The structure units include the hexagonal pin cells and gap cells appearing at the assembly boundary. Therefore, the CMFD module is programmed to deal with the unstructured cells such as the gap cells. The CMFD equation consists of the two parts of (1) the conventional FDM and (2) the current corrective parts. Since the second part of the CMFD equation guarantees the reproducibility of the radial MOC transport solutions for the cell averaged reaction rate and the net current at the cell surfaces, how to build the first part of the CMFD equation is not important. Therefore, the first part of the CMFD equation is roughly built by using the normal distance from the gravity center to the surface. The VHTR core uses helium as a coolant which is realized as a void hole in a neutronics calculation. This void hole which

The influence of alloying on the phase formation sequence of ultra-thin nickel silicide films and on the inheritance of texture

Science.gov (United States)

Geenen, F. A.; Solano, E.; Jordan-Sweet, J.; Lavoie, C.; Mocuta, C.; Detavernier, C.

2018-05-01

The controlled formation of silicide materials is an ongoing challenge to facilitate the electrical contact of Si-based transistors. Due to the ongoing miniaturisation of the transistor, the silicide is trending to ever-thinner thickness's. The corresponding increase in surface-to-volume ratio emphasises the importance of low-energetic interfaces. Intriguingly, the thickness reduction of nickel silicides results in an abrupt change in phase sequence. This paper investigates the sequence of the silicides phases and their preferential orientation with respect to the Si(001) substrate, for both "thin" (i.e., 9 nm) and "ultra-thin" (i.e., 3 nm) Ni films. Furthermore, as the addition of ternary elements is often considered in order to tailor the silicides' properties, additives of Al, Co, and Pt are also included in this study. Our results show that the first silicide formed is epitaxial θ-Ni2Si, regardless of initial thickness or alloyed composition. The transformations towards subsequent silicides are changed through the additive elements, which can be understood through solubility arguments and classical nucleation theory. The crystalline alignment of the formed silicides with the substrate significantly differs through alloying. The observed textures of sequential silicides could be linked through texture inheritance. Our study illustrates the nucleation of a new phase drive to reduce the interfacial energy at the silicide-substrate interface as well as at the interface with the silicide which is being consumed for these sub-10 nm thin films.

Nanoscale investigation of the interface situation of plated nickel and thermally formed nickel silicide for silicon solar cell metallization

Science.gov (United States)

Mondon, A.; Wang, D.; Zuschlag, A.; Bartsch, J.; Glatthaar, M.; Glunz, S. W.

2014-12-01

In the context of nickel silicide formation from plated nickel layers for solar cell metallization, there are several open questions regarding contact adhesion and electrical properties. Nanoscale characterization by transmission electron microscopy has been employed to support these investigations. Interfacial oxides and silicide phases were investigated on differently prepared samples by different analytical methods associated with transmission electron microscopy analysis. Processing variations included the pre-treatment of samples before nickel plating, the used plating solution and the thermal budget for the nickel-silicon solid-state reaction. It was shown that interface oxides of only few nm thickness on both silicon and nickel silicide are present on the samples, depending on the chosen process sequence, which have been shown to play an important role in adhesion of nickel on silicide in an earlier publication. From sample pretreatment variations, conclusions about the role of an interfacial oxide in silicide formation and its influence on phase formation were drawn. Such an oxide layer hinders silicide formation except for pinhole sites. This reduces the availability of Ni and causes a silicide with low Ni content to form. Without an interfacial oxide a continuous nickel silicide of greater depth, polycrystalline modification and expected phase according to thermal budget is formed. Information about the nature of silicide growth on typical solar cell surfaces could be obtained from silicide phase and geometric observations, which were supported by FIB tomography. The theory of isotropic NiSi growth and orientation dependent NiSi2 growth was derived. By this, a very well performing low-cost metallization for silicon solar cells has been brought an important step closer to industrial introduction.

Considerations on the influence of fission products in whole core accidents

International Nuclear Information System (INIS)

Meyer Heine, A.; Pattoret, A.; Schmitz, F.

1977-01-01

If the hypothetical Whole Core Accidents which are taken into account in reactor safety analysis can change from one country to another, there is nevertheless a general agreement over their description and main phases. Furthermore the important parameters have also been identified by every laboratory. During the development of such core accidents the role of the fission products in essential. It is not the purpose of this paper to give an exhaustive description of the phases which can be influenced by the fission products, we will try however to focus this study on the most important ones. In a second step we will discuss the equation of state of irradiated fuels; here again one principal preoccupation being to quantify the influence of fission products on reactor accidents. It is not our purpose to enter on the fundamental aspects of the equation of state. The studies and the experimental program launched at the CEA will then be described. Special attention will be directed towards the eventual role of fission products in molten fuel-coolant interactions (MFCls) or the events leading to the initiation of whole core accidents. This paper will be limited to oxide fuels. Whether the whole core accident is initiated by a reactivity defect or a coolant coast-down, one has to deal with four great categories of phenomena. Loss of flow: the power is around the nominal value, while the coolant flow has been reduced by a factor of 5 to 10. This induces boiling and clad weakening. Will the plenum pressure lead to a clad rupture? In case of a rupture, what will be the effect on the voiding of the channel? Transient over power: influence of gases from gaseous and volatile fission products on the fuel movements? MFCIs: Influence of the fission products in the mode of contact between fuel and coolant? Influence on the fuel characteristics. Sodium vapour bubble expansion: influence of the fission products on the heat transfer and eventual condensation of the bubble?

No association of the neuropeptide Y (Leu7Pro) and ghrelin gene (Arg51Gln, Leu72Met, Gln90Leu) single nucleotide polymorphisms with eating disorders.

Science.gov (United States)

Kindler, Jochen; Bailer, Ursula; de Zwaan, Martina; Fuchs, Karoline; Leisch, Friedrich; Grün, Bettina; Strnad, Alexandra; Stojanovic, Mirjana; Windisch, Julia; Lennkh-Wolfsberg, Claudia; El-Giamal, Nadja; Sieghart, Werner; Kasper, Siegfried; Aschauer, Harald

2011-06-01

Genetic factors likely contribute to the biological vulnerability of eating disorders. Case-control association study on one neuropeptide Y gene (Leu7Pro) polymorphism and three ghrelin gene (Arg51Gln, Leu72Met and Gln90Leu) polymorphisms. 114 eating disorder patients (46 with anorexia nervosa, 30 with bulimia nervosa, 38 with binge eating disorder) and 164 healthy controls were genotyped. No differences were detected between patients and controls for any of the four polymorphisms in allele frequency and genotype distribution (P > 0.05). Allele frequencies and genotypes had no significant influence on body mass index (P > 0.05) in eating disorder patients. Positive findings of former case-control studies of associations between ghrelin gene polymorphisms and eating disorders could not be replicated. Neuropeptide Y gene polymorphisms have not been investigated in eating disorders before.

A Study on Silicide Coatings as Diffusion barrier for U-7Mo Dispersion Fuel

Energy Technology Data Exchange (ETDEWEB)

Won, Ju Jin; Kim, Sung Hwan; Lee, Kyu Hong; Jeong, Yong Jin; Kim, Ki Nam; Park, Jong Man; Lee, Chong Tak [KAERI, Daejeon (Korea, Republic of)

2016-05-15

Gamma phase U-Mo alloys are regarded as one of the promising candidates for advanced research reactor fuel when it comes to the irradiation performance. However, it has been reported that interaction layer formation between the UMo alloys and Al matrix degrades the irradiation performance of U-Mo dispersion fuel. The excessive interaction between the U-Mo alloys and their surrounding Al matrix lead to excessive local swelling called 'pillowing'. For this reason, KAERI suggested several remedies such as alloying U-Mo with Al matrix with Si. In addition, silicide or nitride coatings on the surface of U-Mo particles have also been proposed to hinder the growth of the interaction layer. In this study, centrifugally atomized U-7Mo alloy powders were coated with silicide layers at 900 .deg. C for 1hr. U-Mo alloy powder was mixed with MoSi{sub 2}, Si and ZrSi{sub 2} powders and subsequently heat-treated to form uranium-silicide coating layers on the surface of U-Mo alloy particles. Silicide coated U-Mo powders and characterized using scanning electron microscopy (SEM), energy dispersive x-ray spectroscopy (EDS) and X-ray diffractometer (XRD). The ZrSi{sub 2} coating layers has a thickness of about 1∼ 2μm. The surface of a silicide coated particle was very rough and silicide powder attached to the surface of the coating layer. 3. The XRD analysis of the coating layers showed that, they consisted of compounds such as U3Si{sub 2}, USi{sub 2}.

Irradiation of MEU and LEU test fuel elements in DR 3

International Nuclear Information System (INIS)

Haack, K.

1984-01-01

Irradiation of three MEU and three LEU fuel elements in the Danish reactor DR 3. Thermal and fast neutron flux density scans of the core have been made and the results, related to the U235-content of each fuel element, are compared with the values from HEU fuel elements. The test elements were taken to burn-up percentages of 50-60%. Reactivity values of the test elements at charge and at discharge have been measured and the values are compared with those of HEU fuel elements. (author)

Peptide (Lys-Leu) and amino acids (Lys and Leu) supplementations improve physiological activity and fermentation performance of brewer's yeast during very high-gravity (VHG) wort fermentation.

Science.gov (United States)

Yang, Huirong; Zong, Xuyan; Cui, Chun; Mu, Lixia; Zhao, Haifeng

2017-12-22

Lys and Leu were generally considered as the key amino acids for brewer's yeast during beer brewing. In the present study, peptide Lys-Leu and a free amino acid (FAA) mixture of Lys and Leu (Lys + Leu) were supplemented in 24 °P wort to examine their effects on physiological activity and fermentation performance of brewer's yeast during very high-gravity (VHG) wort fermentation. Results showed that although both peptide Lys-Leu and their FAA mixture supplementations could increase the growth and viability, intracellular trehalose and glycerol content, wort fermentability, and ethanol content for brewer's yeast during VHG wort fermentation, and peptide was better than their FAA mixture at promoting growth and fermentation for brewer's yeast when the same dose was kept. Moreover, peptide Lys-Leu supplementation significantly increased the assimilation of Asp, but decreased the assimilation of Gly, Ala, Val, (Cys)2, Ile, Leu, Tyr, Phe, Lys, Arg, and Pro. However, the FAA mixture supplementation only promoted the assimilation of Lys and Leu, while reduced the absorption of total amino acids to a greater extent. Thus, the peptide Lys-Leu was more effective than their FAA mixture on the improvement of physiological activity, fermentation performance, and nitrogen metabolism of brewer's yeast during VHG wort fermentation. © 2017 International Union of Biochemistry and Molecular Biology, Inc.

Loading and initial start-up testing of the low-enrichment uranium core for the Ohio State University research reactor

International Nuclear Information System (INIS)

Talnagi, J.W.

1989-01-01

Conversion of the Ohio State University Research Reactor (OSURR) from high-enrichment uranium (HEU) fuel to low-enrichment uranium (LEU) fuel elements was begun in August 1985, with funding provided by the U.S. Department of Energy (DOE) and the university. Conversion of the OSURR from HEU to LEU fuel was successfully completed. The reactor is operational at 10-kW steady-state thermal power. Measurements of selected core parameters have been made and compared with predicted values and previous values for the HEU core. In general, measured results agree well with predicted performance, and minor changes have been detected in certain core parameters as a result of the change to LEU fuel. Future plans include additional core testing and a possible increase in operating power

Evaluation of anomalies during nickel and titanium silicide formation using the effective heat of formation mode

CSIR Research Space (South Africa)

Pretorius, R

1993-11-01

Full Text Available , as well as the observed sequence of growth of different silicide phases, are not in agree- ment with thermodynamic considerations [26]. In the case of the nickel silicides Ni,Si is nearly always found to be the first... to determine how the oxygen content in the silicon affects phase formation. We also show how the anomalous behaviour of titanium and nickel silicide formation can be explained thermodynamically by using the ?effective heat...

Neutronic analysis of the ford nuclear reactor leu core

International Nuclear Information System (INIS)

Raza, S.S.; Hayat, T.

1989-08-01

Neutronic analysis of the ford nuclear reactor low enriched uranium core has been carried out to gain confidence in the com puting methodology being used for Pakistan Research Reactor-1 core conversion calculations. The computed value of the effective multiplication factor (Keff) is found to be in good agreement with that quoted by others. (author). 6 figs

Fuel management strategy for the compact core design of RSG GAS (MPR-30)

Energy Technology Data Exchange (ETDEWEB)

Sembiring, T.M.; Liem, P.H.; Tukiran, S. [National Nuclear Energy Agency (Batan), PUSPIPTEK-Serpong Tangerang (Indonesia)

2000-07-01

The rearrangement of the core configuration of the RSG GAS reactor to obtain a compact core is in progress. A fuel management strategy is proposed for the equilibrium compact core of this reactor by reducing the number of in-core irradiation positions. The reduced irradiation positions are based on the activities during 12 years operation. The obtained compact core gives significant extension of the operation cycle length so that the reactor availability and utilization can be enhanced. The equilibrium compact silicide core obtained met the imposed design constraints and safety requirements. (author)

Fuel management strategy for the compact core design of RSG GAS (MPR-30)

International Nuclear Information System (INIS)

Sembiring, T.M.; Liem, P.H.; Tukiran, S.

2000-01-01

The rearrangement of the core configuration of the RSG GAS reactor to obtain a compact core is in progress. A fuel management strategy is proposed for the equilibrium compact core of this reactor by reducing the number of in-core irradiation positions. The reduced irradiation positions are based on the activities during 12 years operation. The obtained compact core gives significant extension of the operation cycle length so that the reactor availability and utilization can be enhanced. The equilibrium compact silicide core obtained met the imposed design constraints and safety requirements. (author)

A procedure for searching the equilibrium core of a research reactor

International Nuclear Information System (INIS)

Bakri Arbie; Liem Peng Hong; Prayoto

1996-01-01

A procedure for searching the equilibrium core of a research reactor has been proposed. The searching procedure is based on the relaxation method and has been implemented in Batan-EQUIL-2D in-core fuel management code. The few-group neutron diffusion theory in 2-D, X-Y, and R-Z reactor geometries are adopted as the framework of the code. The successful applicability of the procedure for obtaining the new RSG-GAS (MPR-30) silicide equilibrium core was shown. (author)

Pt silicide/poly-Si Schottky diodes as temperature sensors for bolometers

Energy Technology Data Exchange (ETDEWEB)

Yuryev, V. A., E-mail: vyuryev@kapella.gpi.ru; Chizh, K. V.; Chapnin, V. A.; Mironov, S. A.; Dubkov, V. P.; Uvarov, O. V.; Kalinushkin, V. P. [A. M. Prokhorov General Physics Institute of the Russian Academy of Sciences, 38 Vavilov Street, Moscow 119991 (Russian Federation); Senkov, V. M. [P. N. Lebedev Physical Institute of the Russian Academy of Sciences, 53 Leninskiy Avenue, Moscow 119991 (Russian Federation); Nalivaiko, O. Y. [JSC “Integral” – “Integral” Holding Management Company, 121A, Kazintsa I. P. Street, Minsk 220108 (Belarus); Novikau, A. G.; Gaiduk, P. I. [Belarusian State University, 4 Nezavisimosti Avenue, 220030 Minsk (Belarus)

2015-05-28

Platinum silicide Schottky diodes formed on films of polycrystalline Si doped by phosphorus are demonstrated to be efficient and manufacturable CMOS-compatible temperature sensors for microbolometer detectors of radiation. Thin-film platinum silicide/poly-Si diodes have been produced by a CMOS-compatible process on artificial Si{sub 3}N{sub 4}/SiO{sub 2}/Si(001) substrates simulating the bolometer cells. Layer structure and phase composition of the original Pt/poly-Si films and the Pt silicide/poly-Si films synthesized by a low-temperature process have been studied by means of the scanning transmission electron microscopy; they have also been explored by means of the two-wavelength X-ray structural phase analysis and the X-ray photoelectron spectroscopy. Temperature coefficient of voltage for the forward current of a single diode is shown to reach the value of about −2%/ °C in the temperature interval from 25 to 50 °C.

Preliminary Thermohydraulic Analysis of a New Moderated Reactor Utilizing an LEU-Fuel for Space Nuclear Thermal Propulsion

International Nuclear Information System (INIS)

Nam, Seung Hyun; Choi, Jae Young; Venneria, Paolo F.; Jeong, Yong Hoon; Chang, Soon Heung

2015-01-01

The Korea Advanced NUclear Thermal Engine Rocket utilizing an LEU fuel (KANUTER-LEU) is a non-proliferative and comparably efficient NTR engine with relatively low thrust levels of 40 - 50 kN for in-space transportation. The small modular engine can expand mission versatility, when flexibly used in a clustered engine arrangement, so that it can perform various scale missions from low-thrust robotic science missions to high-thrust manned missions. In addition, the clustered engine system can enhance engine redundancy and ensuing crew safety as well as the thrust. The propulsion system is an energy conversion system to transform the thermal energy of the reactor into the kinetic energy of the propellant to produce the powers for thrust, propellant feeding and electricity. It is mainly made up of a propellant Feeding System (PFS) comprising a Turbo-Pump Assembly (TPA), a Regenerative Nozzle Assembly (RNA), etc. For this core design study, an expander cycle is assumed to be the propulsion system. The EGS converts the thermal energy of the EHTGR in the idle operation (only 350 kW th power) to electric power during the electric power mode. This paper presents a preliminary thermohydraulic design analysis to explore the design space for the new reactor and to estimate the referential engine performance. The new non-proliferative NTR engine concept, KANUTER-LEU, is under designing to surmount the nuclear proliferation obstacles on allR and Dactivities and eventual commercialization for future generations. To efficiently implement a heavy LEU fuel for the NTR engine, its reactor design innovatively possesses the key characteristics of the high U density fuel with high heating and H 2 corrosion resistances, the thermal neutron spectrum core and also minimizing non-fission neutron loss, and the compact reactor design with protectively cooling capability. To investigate feasible design space for the moderated EHTGR-LEU and resultant engine performance, the preliminary design

Implementation of a Gadolinium Burnable Absorber in the Carbide LEU-NTR

International Nuclear Information System (INIS)

Venneria, Paolo; Kim, Yonghee

2015-01-01

Among the most crucial are the rapid reactivity depletion during full-power operation and the positive reactivity insertion during the full-submersion criticality accident. In previous work, it has been suggested that both challenges can be mitigated through the successful implementation of a burnable absorber in the active core. Of the poisons previously surveyed, one of the most promising is Gadolinium in the form of Gadolina (Gd2O4). This paper explores the possibility of different methods by which the Gadolinia can be implemented in the core and makes a preliminary study of its effect on the full submersion criticality accident and the reactivity depletion during operation. The application of a Gadolinium neutron absorber in the active core region of the LEU-NTR has been shown to be neutronically feasible. It can be introduced into the core in various locations without resulting in core performance loss. The utility of the poison in terms of mitigating the full-submersion reactivity accident and the rapid change in reactivity during full-power operation have been preliminarily shown and the first steps towards eventual implementation made. Future work will consist of determining the maximum poison content in the core and tailoring the self-shielding effect in order to determine a specific Gd depletion rate

Synthesis of high specific active tritiated Leu-enkephalin in the leucine residue

Energy Technology Data Exchange (ETDEWEB)

Baba, S.; Hasegawa, H.; Shinohara, Y. (Tokyo Coll. of Pharmacy (Japan))

1989-12-01

Leu-enkephalin labelled with tritium in the Leu residue has been prepared. Synthesis of the precursor peptide, (4,5-dehydroLeu{sup 5}-)Leu-enkephalin, was carried out by solid phase synthesis using Fmoc amino acid derivatives. The peptide was tritiated catalytically yielding {sup 3}H-Leu-enkephalin with a specific radioactivity of 4.39 TBq/mmol. The distribution of tritium label was investigated by reversed-phase high performance liquid chromatography with a synchronized accumulating radioisotope detector following acidic and enzymatic hydrolysis, which confirmed that the tritium label was entirely located at the Leu residue. (author).

Induction of CD4 suppressor T cells with anti-Leu-8 antibody

International Nuclear Information System (INIS)

Kanof, M.E.; Strober, W.; James, S.P.

1987-01-01

To characterize the conditions under which CD4 T cells suppress polyclonal immunoglobulin synthesis, we investigated the capacity of CD4 T cells that coexpress the surface antigen recognized by the monoclonal antibody anti-Leu-8 to mediate suppression. In an in vitro system devoid of CD8 T cells, CD4, Leu-8+ T cells suppressed pokeweed mitogen-induced immunoglobulin synthesis. Similarly, suppressor function was induced in unfractionated CD4 T cell populations after incubation with anti-Leu-8 antibody under cross-linking conditions. This induction of suppressor function by anti-Leu-8 antibody was not due to expansion of the CD4, Leu-8+ T cell population because CD4 T cells did not proliferate in response to anti-Leu-8 antibody. However, CD4, Leu-8+ T cell-mediated suppression was radiosensitive. Finally, CD4, Leu-8+ T cells do not inhibit immunoglobulin synthesis when T cell lymphokines were used in place of helper CD4 T cells (CD4, Leu-8- T cells), suggesting that CD4 T cell-mediated suppression occurs at the T cell level. We conclude that CD4 T cells can be induced to suppress immunoglobulin synthesis by modulation of the membrane antigen recognized by anti-Leu-8 antibody

Core cooling and thermal responses during whole-head, facial, and dorsal immersion in 17 degrees C water.

Science.gov (United States)

Pretorius, Thea; Gagnon, Dominique D; Giesbrecht, Gordon G

2010-10-01

This study isolated the effects of dorsal, facial, and whole-head immersion in 17 degrees C water on peripheral vasoconstriction and the rate of body core cooling. Seven male subjects were studied in thermoneutral air (approximately 28 degrees C). On 3 separate days, they lay prone or supine on a bed with their heads inserted through the side of an adjustable immersion tank. Following 10 min of baseline measurements, the water level was raised such that the water immersed the dorsum, face, or whole head, with the immersion period lasting 60 min. During the first 30 min, the core (esophageal) cooling rate increased from dorsum (0.29 ± 0.2 degrees C h-1) to face (0.47 ± 0.1 degrees C h-1) to whole head (0.69 ± 0.2 degrees C h(-1)) (p whole-head immersion (114 ± 52% h(-1)) than in either facial (51 ± 47% h-1) or dorsal (41 ± 55% h(-1)) immersion (p whole-head (120.5 ± 13 kJ), facial (86.8 ± 17 kJ), and dorsal (46.0 ± 11 kJ) immersion (p whole head elicited a higher rate of vasoconstriction, the face did not elicit more vasoconstriction than the dorsum. Rather, the progressive increase in core cooling from dorsal to facial to whole-head immersion simply correlates with increased heat loss.

Development of Fission Mo-99 Process for LEU Dispersion Target

Energy Technology Data Exchange (ETDEWEB)

Lee, Seung Kon; Lee, Su Seung; Hong, Soon Bog; Jang, Kyung Duk; Park, Ul Jae; Lee, Jun Sig [KAERI, Daejeon (Korea, Republic of)

2016-05-15

KAERI (Korea Atomic Energy Research Institute) is developing LEU-based fission {sup 99}Mo production process which is connected to the new research reactor (Kijang New Research Reactor, KJRR), which is being constructed in Gijang, Busan, Korea. Historically, the most fission {sup 99}Mo producers have been used highly enriched uranium (HEU) targets so far. However, to reduce the use of HEU in private sector for non-proliferation, {sup 99}Mo producers are forced to convert their HEU-based process to use low enriched uranium (LEU) targets. Economic impact of a target conversion from HEU to LEU is significant. Overall cost for the production of the fission {sup 99}Mo increases significantly with the conversion of fission {sup 99}Mo targets from HEU to LEU. It is not only because the yield of LEU is only 50% of HEU, but also because radioactive waste production increases 200%. On the basis, worldwide efforts on the development of {sup 99}Mo production process that is optimized for the LEU target become an important issue. In this study, fission {sup 99}Mo process with non-irradiated LEU targets was presented except separation and purification steps. Pre- and post-irradiation tests of the fission {sup 99}Mo target will be done in 4th quarter of 2016.

Development of Fission Mo-99 Process for LEU Dispersion Target

International Nuclear Information System (INIS)

Lee, Seung Kon; Lee, Su Seung; Hong, Soon Bog; Jang, Kyung Duk; Park, Ul Jae; Lee, Jun Sig

2016-01-01

KAERI (Korea Atomic Energy Research Institute) is developing LEU-based fission 99 Mo production process which is connected to the new research reactor (Kijang New Research Reactor, KJRR), which is being constructed in Gijang, Busan, Korea. Historically, the most fission 99 Mo producers have been used highly enriched uranium (HEU) targets so far. However, to reduce the use of HEU in private sector for non-proliferation, 99 Mo producers are forced to convert their HEU-based process to use low enriched uranium (LEU) targets. Economic impact of a target conversion from HEU to LEU is significant. Overall cost for the production of the fission 99 Mo increases significantly with the conversion of fission 99 Mo targets from HEU to LEU. It is not only because the yield of LEU is only 50% of HEU, but also because radioactive waste production increases 200%. On the basis, worldwide efforts on the development of 99 Mo production process that is optimized for the LEU target become an important issue. In this study, fission 99 Mo process with non-irradiated LEU targets was presented except separation and purification steps. Pre- and post-irradiation tests of the fission 99 Mo target will be done in 4th quarter of 2016

Milling uranium silicide powder for dispersion nuclear fuels

Energy Technology Data Exchange (ETDEWEB)

Vieira, E.; Silva, D.G.; Souza, J.A.B.; Durazzo, M. [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil); Riella, H.G. [Universidade Federal de Santa Catarina (UFSC), Florianopolis, SC (Brazil)

2009-07-01

Full text: Uranium silicide (U3Si2) is presently considered the best fuel qualified so far in terms of uranium loading and performance. Stability of the U3Si2 fuel with uranium density of 4.8 g/cm3 was confirmed by burnup stability tests performed during the Reduced Enrichment for Research and Test Reactors (RERTR) program. This fuel was chosen to compose the first core of the new Brazilian Multipurpose Research Reactor (RMB), planned to be constructed in the next years. This new reactor will consume bigger quantities of U3Si2 powder, when compared with the small consumption of the IEA-R1 research reactor of IPEN-CNEN/SP, the unique MTR type research reactor operating in the country. At the present time, the milling operation of U3Si2 ingots is made manually. In order to increase the powder production capacity, the manual milling must be replaced by an automated procedure. This paper describes a new milling machine and procedure developed to produce U3Si2 powder with higher efficiency. (author)

Molybdenum silicide based materials and their properties

International Nuclear Information System (INIS)

Yao, Z.; Stiglich, J.; Sudarshan, T.S.

1999-01-01

Molybdenum disilicide (MoSi 2 ) is a promising candidate material for high temperature structural applications. It is a high melting point (2030 C) material with excellent oxidation resistance and a moderate density (6.24 g/cm 3 ). However, low toughness at low temperatures and high creep rates at elevated temperatures have hindered its commercialization in structural applications. Much effort has been invested in MoSi 2 composites as alternatives to pure molybdenum disilicide for oxidizing and aggressive environments. Molybdenum disilicide-based heating elements have been used extensively in high-temperature furnaces. The low electrical resistance of silicides in combination with high thermal stability, electron-migration resistance, and excellent diffusion-barrier characteristics is important for microelectronic applications. Projected applications of MoSi 2 -based materials include turbine airfoils, combustion chamber components in oxidizing environments, missile nozzles, molten metal lances, industrial gas burners, diesel engine glow plugs, and materials for glass processing. On this paper, synthesis, fabrication, and properties of the monolithic and composite molybdenum silicides are reviewed

[Leu31, Pro34]neuropeptide Y

DEFF Research Database (Denmark)

Fuhlendorff, J; Gether, U; Aakerlund, L

1990-01-01

Two types of binding sites have previously been described for 36-amino acid neuropeptide Y (NPY), called Y1 and Y2 receptors. Y2 receptors can bind long C-terminal fragments of NPY-e.g., NPY-(13-36)-peptide. In contrast, Y1 receptors have until now only been characterized as NPY receptors that do...... not bind such fragments. In the present study an NPY analog is presented, [Leu31, Pro34]NPY, which in a series of human neuroblastoma cell lines and on rat PC-12 cells can displace radiolabeled NPY only from cells that express Y1 receptors and not from those expressing Y2 receptors. The radiolabeled analog......, [125I-Tyr36] monoiodo-[Leu31, Pro34]NPY, also binds specifically only to cells with Y1 receptors. The binding of this analog to Y1 receptors on human neuroblastoma cells is associated with a transient increase in cytoplasmic free calcium concentrations similar to the response observed with NPY. [Leu31...

31 CFR 540.308 - Low Enriched Uranium (LEU).

Science.gov (United States)

2010-07-01

... 31 Money and Finance: Treasury 3 2010-07-01 2010-07-01 false Low Enriched Uranium (LEU). 540.308... OF FOREIGN ASSETS CONTROL, DEPARTMENT OF THE TREASURY HIGHLY ENRICHED URANIUM (HEU) AGREEMENT ASSETS CONTROL REGULATIONS General Definitions § 540.308 Low Enriched Uranium (LEU). The term low enriched...

The tetrapeptide Arg-Leu-Tyr-Glu inhibits VEGF-induced angiogenesis

International Nuclear Information System (INIS)

Baek, Yi-Yong; Lee, Dong-Keon; So, Ju-Hoon; Kim, Cheol-Hee; Jeoung, Dooil; Lee, Hansoo; Choe, Jongseon; Won, Moo-Ho; Ha, Kwon-Soo; Kwon, Young-Guen; Kim, Young-Myeong

2015-01-01

Kringle 5, derived from plasminogen, is highly capable of inhibiting angiogenesis. Here, we have designed and synthesized 10 tetrapeptides, based on the amino acid properties of the core tetrapeptide Lys-Leu-Tyr-Asp (KLYD) originating from anti-angiogenic kringle 5 of human plasminogen. Of these, Arg-Leu-Tyr-Glu (RLYE) effectively inhibited vascular endothelial growth factor (VEGF)-induced endothelial cell proliferation, migration and tube formation, with an IC 50 of 0.06–0.08 nM, which was about ten-fold lower than that of the control peptide KLYD (0.79 nM), as well as suppressed developmental angiogenesis in a zebrafish model. Furthermore, this peptide effectively inhibited the cellular events that precede angiogenesis, such as ERK and eNOS phosphorylation and nitric oxide production, in endothelial cells stimulated with VEGF. Collectively, these data demonstrate that RLYE is a potent anti-angiogenic peptide that targets the VEGF signaling pathway. - Highlights: • The tetrapeptide RLYE inhibited VEGF-induced angiogenesis in vitro. • RLYE also suppressed neovascularization in a zebrafish model. • Its effect was correlated with inhibition of VEGF-induced ERK and eNOS activation. • RLYE may be used as a therapeutic drug for angiogenesis-related diseases

The tetrapeptide Arg-Leu-Tyr-Glu inhibits VEGF-induced angiogenesis

Energy Technology Data Exchange (ETDEWEB)

Baek, Yi-Yong; Lee, Dong-Keon [Department of Molecular and Cellular Biochemistry, School of Medicine, Kangwon National University, Chuncheon, Gangwon-do, 200-702 (Korea, Republic of); So, Ju-Hoon; Kim, Cheol-Hee [Department of Biology, Chungnam National University, Daejeon, 305-764 (Korea, Republic of); Jeoung, Dooil [Department of Biochemistry, College of Natural Sciences, Kangwon National University, Chuncheon, Gangwon-do, 200-702 (Korea, Republic of); Lee, Hansoo [Department of Life Sciences, College of Natural Sciences, Kangwon National University, Chuncheon, Gangwon-do, 200-702 (Korea, Republic of); Choe, Jongseon [Department of Immunology, School of Medicine, Kangwon National University, Chuncheon, Gangwon-do, 200-702 (Korea, Republic of); Won, Moo-Ho [Department of Neurobiology, School of Medicine, Kangwon National University, Chuncheon, Gangwon-do, 200-702 (Korea, Republic of); Ha, Kwon-Soo [Department of Molecular and Cellular Biochemistry, School of Medicine, Kangwon National University, Chuncheon, Gangwon-do, 200-702 (Korea, Republic of); Kwon, Young-Guen [Department of Biochemistry, College of Life Science and Biotechnology, Yonsei University, Seoul, 120-752 (Korea, Republic of); Kim, Young-Myeong, E-mail: ymkim@kangwon.ac.kr [Department of Molecular and Cellular Biochemistry, School of Medicine, Kangwon National University, Chuncheon, Gangwon-do, 200-702 (Korea, Republic of)

2015-08-07

Kringle 5, derived from plasminogen, is highly capable of inhibiting angiogenesis. Here, we have designed and synthesized 10 tetrapeptides, based on the amino acid properties of the core tetrapeptide Lys-Leu-Tyr-Asp (KLYD) originating from anti-angiogenic kringle 5 of human plasminogen. Of these, Arg-Leu-Tyr-Glu (RLYE) effectively inhibited vascular endothelial growth factor (VEGF)-induced endothelial cell proliferation, migration and tube formation, with an IC{sub 50} of 0.06–0.08 nM, which was about ten-fold lower than that of the control peptide KLYD (0.79 nM), as well as suppressed developmental angiogenesis in a zebrafish model. Furthermore, this peptide effectively inhibited the cellular events that precede angiogenesis, such as ERK and eNOS phosphorylation and nitric oxide production, in endothelial cells stimulated with VEGF. Collectively, these data demonstrate that RLYE is a potent anti-angiogenic peptide that targets the VEGF signaling pathway. - Highlights: • The tetrapeptide RLYE inhibited VEGF-induced angiogenesis in vitro. • RLYE also suppressed neovascularization in a zebrafish model. • Its effect was correlated with inhibition of VEGF-induced ERK and eNOS activation. • RLYE may be used as a therapeutic drug for angiogenesis-related diseases.

Radiological consequence analysis with HEU and LEU fuels

Energy Technology Data Exchange (ETDEWEB)

Woodruff, W.L.; Warinner, D.K.; Matos, J.E.

1984-01-01

A model for estimating the radiological consequences from a hypothetical accident in HEU and LEU fueled research and test reactors is presented. Simple hand calculations based on fission product yield table inventories and non-site specific dispersion data may be adequate in many cases. However, more detailed inventories and site specific data on meteorological conditions and release rates and heights can result in substantial reductions in the dose estimates. LEU fuel gives essentially the same doses as HEU fuel. The plutonium buildup in the LEU fuel does not significantly increase the radiological consequences. The dose to the thyroid is the limiting dose. 10 references, 3 figures, 7 tables.

Radiological consequence analysis with HEU and LEU fuels

International Nuclear Information System (INIS)

Woodruff, W.L.; Warinner, D.K.; Matos, J.E.

1984-01-01

A model for estimating the radiological consequences from a hypothetical accident in HEU and LEU fueled research and test reactors is presented. Simple hand calculations based on fission product yield table inventories and non-site specific dispersion data may be adequate in many cases. However, more detailed inventories and site specific data on meteorological conditions and release rates and heights can result in substantial reductions in the dose estimates. LEU fuel gives essentially the same doses as HEU fuel. The plutonium buildup in the LEU fuel does not significantly increase the radiological consequences. The dose to the thyroid is the limiting dose. 10 references, 3 figures, 7 tables

Production of MO-99 from LEU targets-base-side processing

International Nuclear Information System (INIS)

Vandegrift, George F.; Koma, Yoshikazu; Cols, Hector; Conner, Cliff; Aase, Scott; Peter, Magdalin; Walker, David; Leonard, Ralph A.; Snelgrove, James L.

2000-01-01

Argonne National Laboratory (ANL) is cooperating with the Argentine Comision Nacional de Energia Atomica (CNEA) to convert their 99 Mo production process, which uses high enriched uranium (HEU), to low-enriched uranium (LEU). Progress discussed in this year's paper includes optimization of (1) the digestion of LEU foil by sodium hydroxide solution and (2) the primary recovery of molybdenum by anion exchange. Also discussed are ANL/CNEA plans for demonstrating the irradiation and digestion of LEU-foil targets and recovering 99 Mo in Argentina later this year. Our results show that, up to this point in our study, conversion of the CNEA process to LEU appears viable. (author)

Whole core calculations of power reactors by Monte Carlo method

International Nuclear Information System (INIS)

Nakagawa, Masayuki; Mori, Takamasa

1993-01-01

Whole core calculations have been performed for a commercial size PWR and a prototype LMFBR by using vectorized Monte Carlo codes. Geometries of cores were precisely represented in a pin by pin model. The calculated parameters were k eff , control rod worth, power distribution and so on. Both multigroup and continuous energy models were used and the accuracy of multigroup approximation was evaluated through the comparison of both results. One million neutron histories were tracked to considerably reduce variances. It was demonstrated that the high speed vectorized codes could calculate k eff , assembly power and some reactivity worths within practical computation time. For pin power and small reactivity worth calculations, the order of 10 million histories would be necessary. Required number of histories to achieve target design accuracy were estimated for those neutronic parameters. (orig.)

Development of 2-D/1-D fusion method for three-dimensional whole-core heterogeneous neutron transport calculations

International Nuclear Information System (INIS)

Lee, Gil Soo

2006-02-01

To describe power distribution and multiplication factor of a reactor core accurately, it is necessary to perform calculations based on neutron transport equation considering heterogeneous geometry and scattering angles. These calculations require very heavy calculations and were nearly impossible with computers of old days. From the limitation of computing power, traditional approach of reactor core design consists of heterogeneous transport calculation in fuel assembly level and whole core diffusion nodal calculation with assembly homogenized properties, resulting from fuel assembly transport calculation. This approach may be effective in computation time, but it gives less accurate results for highly heterogeneous problems. As potential for whole core heterogeneous transport calculation became more feasible owing to rapid development of computing power during last several years, the interests in two and three dimensional whole core heterogeneous transport calculations by deterministic method are increased. For two dimensional calculation, there were several successful approaches using even parity transport equation with triangular meshes, S N method with refined rectangular meshes, the method of characteristics (MOC) with unstructured meshes, and so on. The work in this thesis originally started from the two dimensional whole core heterogeneous transport calculation by using MOC. After successful achievement in two dimensional calculation, there were efforts in three-dimensional whole-core heterogeneous transport calculation using MOC. Since direct extension to three dimensional calculation of MOC requires too much computing power, indirect approach to three dimensional calculation was considered.Thus, 2D/1D fusion method for three dimensional heterogeneous transport calculation was developed and successfully implemented in a computer code. The 2D/1D fusion method is synergistic combination of the MOC for radial 2-D calculation and S N -like methods for axial 1

Estimation of reactor core calculation by HELIOS/MASTER at power generating condition through DeCART, whole-core transport code

International Nuclear Information System (INIS)

Kim, H. Y.; Joo, H. G.; Kim, K. S.; Kim, G. Y.; Jang, M. H.

2003-01-01

The reactivity and power distribution errors of the HELIOS/MASTER core calculation under power generating conditions are assessed using a whole core transport code DeCART. For this work, the cross section tablesets were generated for a medium sized PWR following the standard procedure and two group nodal core calculations were performed. The test cases include the HELIOS calculations for 2-D assemblies at constant thermal conditions, MASTER 3D assembly calculations at power generating conditions, and the core calculations at HZP, HFP, and an abnormal power conditions. In all these cases, the results of the DeCART code in which pinwise thermal feedback effects are incorporated are used as the reference. The core reactivity, assemblywise power distribution, axial power distribution, peaking factor, and thermal feedback effects are then compared. The comparison shows that the error of the HELIOS/MASTER system in the core reactivity, assembly wise power distribution, pin peaking factor are only 100∼300 pcm, 3%, and 2%, respectively. As far as the detailed pinwise power distribution is concerned, however, errors greater than 15% are observed

Documentation Experiences for Jamaican SLOWPOKE-2 Conversion from HEU to LEU

International Nuclear Information System (INIS)

Warner, T.-A.; Dennis, H.; Antoine, J.

2015-01-01

The Jamaican SLOWPOKE–2 (JM–1) is a 20 kW research reactor manufactured by Atomic Energy of Canada Limited and has been operating since March 1984, in the department of the International Centre for Environmental and Nuclear Sciences (ICENS), at the University of the West Indies, Mona Campus in Kingston, Jamaica. The pool type reactor has been primarily used for Neutron Activation Analysis in environmental, agricultural, geochemical, health-related studies and mineral exploration. The University, assisted by the IAEA under the GTRI/RERTR program, is currently in the process of converting from HEU to LEU. Extensive documentation on policies, general requirements, elements of the conversion quality assurance (QA) system and conversion QA administrative procedures is required for the conversion. The core conversion activities are being carried out in accordance with current international standards and regulatory guidelines of the newly established Jamaican Radiation Safety Authority (RSA) with agreement between the RSA and IAEA or DOE related to Nuclear Safety and Control. The documentation structure has taken into consideration nuclear safety and licensing, LEU fuel design and conversion analysis, LEU fuel procurement and fabrication, removal of HEU fuel and reactor maintenance and conversion and commissioning, with the conversion QA manual at the apex of the structure. To a large extent, the documentation format will adhere to that of the IAEA applicable regulatory standards and guidance documents. The major challenge of the conversion activities, it is envisioned, will come from the absence of any previous regulatory framework in Jamaica; however, a timeline for the process, which includes training and equipping of regulators, will guide operation. (author)

Parallelization characteristics of a three-dimensional whole-core code DeCART

International Nuclear Information System (INIS)

Cho, J. Y.; Joo, H.K.; Kim, H. Y.; Lee, J. C.; Jang, M. H.

2003-01-01

Neutron transport calculation for three-dimensional amount of computing time but also huge memory. Therefore, whole-core codes such as DeCART need both also parallel computation and distributed memory capabilities. This paper is to implement such parallel capabilities based on MPI grouping and memory distribution on the DeCART code, and then to evaluate the performance by solving the C5G7 three-dimensional benchmark and a simplified three-dimensional SMART core problem. In C5G7 problem with 24 CPUs, a speedup of maximum 22 is obtained on IBM regatta machine and 21 on a LINUX cluster for the MOC kernel, which indicates good parallel performance of the DeCART code. The simplified SMART problem which need about 11 GBytes memory with one processors requires about 940 MBytes, which means that the DeCART code can now solve large core problems on affordable LINUX clusters

Oral delivery of [D-Leu-4]-OB3 and MA-[D-Leu-4]-OB3, synthetic peptide leptin mimetics: Immunofluorescent localization in the mouse hypothalamus.

Science.gov (United States)

Anderson, Brian M; Jacobson, Lauren; Novakovic, Zachary M; Grasso, Patricia

2017-06-01

This study describes the localization of [D-Leu-4]-OB3 and MA-[D-Leu-4]-OB3, synthetic peptide leptin mimetics, in the hypothalamus of Swiss Webster and C57BL/6J wild-type mice, leptin-deficient ob/ob mice, and leptin-resistant diet-induced obese (DIO) mice. The mice were given [D-Leu-4]-OB3 or MA-[D-Leu-4]-OB3 in 0.3% dodecyl maltoside by oral gavage. Once peak serum concentrations were reached, the mice received a lethal dose of pentobarbital and were subjected to intracardiac perfusion fixation. The brains were excised, post-fixed in paraformaldehyde, and cryo-protected in sucrose. Free-floating frozen coronal sections were cut at 25-µm and processed for imaging by immunofluorescence microscopy. In all four strains of mice, dense staining was concentrated in the area of the median eminence, at the base and/or along the inner wall of the third ventricle, and in the brain parenchyma at the level of the arcuate nucleus. These results indicate that [D-Leu-4]-OB3 and MA-[D-Leu-4]-OB3 cross the blood-brain barrier and concentrate in an area of the hypothalamus known to regulate energy balance and glucose homeostasis. Most noteworthy is the localization of [D-Leu-4]-OB3 immunoreactivity within the hypothalamus of DIO mice via a conduit that is closed to leptin in this rodent model, and in most cases of human obesity. Together with our previous studies describing the effects of [D-Leu-4]-OB3 and MA-[D-Leu-4]-OB3 on energy balance, glucose regulation, and signal transduction pathway activation, these findings are consistent with a central mechanism of action for these synthetic peptide leptin mimetics, and suggest their potential usefulness in the management of leptin-resistant obesity and type 2 diabetes in humans. Copyright © 2017 Elsevier B.V. All rights reserved.

Preliminary Thermohydraulic Analysis of a New Moderated Reactor Utilizing an LEU-Fuel for Space Nuclear Thermal Propulsion

Energy Technology Data Exchange (ETDEWEB)

Nam, Seung Hyun; Choi, Jae Young; Venneria, Paolo F.; Jeong, Yong Hoon; Chang, Soon Heung [KAIST, Daejeon (Korea, Republic of)

2015-10-15

The Korea Advanced NUclear Thermal Engine Rocket utilizing an LEU fuel (KANUTER-LEU) is a non-proliferative and comparably efficient NTR engine with relatively low thrust levels of 40 - 50 kN for in-space transportation. The small modular engine can expand mission versatility, when flexibly used in a clustered engine arrangement, so that it can perform various scale missions from low-thrust robotic science missions to high-thrust manned missions. In addition, the clustered engine system can enhance engine redundancy and ensuing crew safety as well as the thrust. The propulsion system is an energy conversion system to transform the thermal energy of the reactor into the kinetic energy of the propellant to produce the powers for thrust, propellant feeding and electricity. It is mainly made up of a propellant Feeding System (PFS) comprising a Turbo-Pump Assembly (TPA), a Regenerative Nozzle Assembly (RNA), etc. For this core design study, an expander cycle is assumed to be the propulsion system. The EGS converts the thermal energy of the EHTGR in the idle operation (only 350 kW{sub th} power) to electric power during the electric power mode. This paper presents a preliminary thermohydraulic design analysis to explore the design space for the new reactor and to estimate the referential engine performance. The new non-proliferative NTR engine concept, KANUTER-LEU, is under designing to surmount the nuclear proliferation obstacles on allR and Dactivities and eventual commercialization for future generations. To efficiently implement a heavy LEU fuel for the NTR engine, its reactor design innovatively possesses the key characteristics of the high U density fuel with high heating and H{sub 2} corrosion resistances, the thermal neutron spectrum core and also minimizing non-fission neutron loss, and the compact reactor design with protectively cooling capability. To investigate feasible design space for the moderated EHTGR-LEU and resultant engine performance, the

Nickel silicide thin films as masking and structural layers for silicon bulk micro-machining by potassium hydroxide wet etching

International Nuclear Information System (INIS)

Bhaskaran, M; Sriram, S; Sim, L W

2008-01-01

This paper studies the feasibility of using titanium and nickel silicide thin films as mask materials for silicon bulk micro-machining. Thin films of nickel silicide were found to be more resistant to wet etching in potassium hydroxide. The use of nickel silicide as a structural material, by fabricating micro-beams of varying dimensions, is demonstrated. The micro-structures were realized using these thin films with wet etching using potassium hydroxide solution on (1 0 0) and (1 1 0) silicon substrates. These results show that nickel silicide is a suitable alternative to silicon nitride for silicon bulk micro-machining

Synthesis, Characterization, and Mechanism of Formation of Janus-Like Nanoparticles of Tantalum Silicide-Silicon (TaSi2/Si

Directory of Open Access Journals (Sweden)

Andrey V. Nomoev

2014-12-01

Full Text Available Metal-semiconductor Janus-like nanoparticles with the composition tantalum silicide-silicon (TaSi2/Si were synthesized for the first time by means of an evaporation method utilizing a high-power electron beam. The composition of the synthesized particles were characterized using high-resolution transmission electron microscopy (HRTEM, X-ray diffraction (XRD, selective area electron diffraction (SAED, and energy dispersive X-ray fluorescence (EDX analysis. The system is compared to previously synthesized core-shell type particles in order to show possible differences responsible for the Janus-like structure forming instead of a core-shell architecture. It is proposed that the production of Janus-like as opposed to core-shell or monophase particles occurs due to the ability of Ta and Si to form compounds and the relative content of Ta and Si atoms in the produced vapour. Based on the results, a potential mechanism of formation for the TaSi2/Si nanoparticles is discussed.

Self-organized patterns along sidewalls of iron silicide nanowires on Si(110) and their origin

Energy Technology Data Exchange (ETDEWEB)

Das, Debolina; Mahato, J. C.; Bisi, Bhaskar; Dev, B. N., E-mail: msbnd@iacs.res.in [Department of Materials Science, Indian Association for the Cultivation of Science, Kolkata 700032 (India); Satpati, B. [Surface Physics and Material Science Division, Saha Institute of Nuclear Physics, 1/AF Bidhannagar, Kolkata 700064 (India)

2014-11-10

Iron silicide (cubic FeSi{sub 2}) nanowires have been grown on Si(110) by reactive deposition epitaxy and investigated by scanning tunneling microscopy and scanning/transmission electron microscopy. On an otherwise uniform nanowire, a semi-periodic pattern along the edges of FeSi{sub 2} nanowires has been discovered. The origin of such growth patterns has been traced to initial growth of silicide nanodots with a pyramidal Si base at the chevron-like atomic arrangement of a clean reconstructed Si(110) surface. The pyramidal base evolves into a comb-like structure along the edges of the nanowires. This causes the semi-periodic structure of the iron silicide nanowires along their edges.

Supply of low enriched (LEU) and highly enriched uranium (HEU) for research reactors

International Nuclear Information System (INIS)

Mueller, H.

1997-01-01

Enriched uranium for research reactors in the form of LEU /= low enriched uranium at 19.75% U-235) and HEU (= highly enriched uranium at 90 to 93% U-235) was and is - due to its high U-235 enrichment - a political fuel other than enriched uranium for power reactors. The sufficient availability of LEU and HEU is a vital question for research reactors, especially in Europe, in order to perform their peaceful research reactor programs. In the past the USA were in the Western hemisphere sole supplier of LEU and HEU. Today the USA have de facto stopped the supply of LEU and HEU, for HEU mainly due to political reasons. This paper deals, among others, with the present availability of LEU and HEU for European research reactors and touches the following topics: - historical US supplies, - influence of the RERTR-program, - characteristics of LEU and HEU, - military HEU enters the civil market, -what is the supply situation for LEU and HEU today? - outlook for safe supplies of LEU and HEU. (author)

Course of pin fuel test In WWR-M reactor core

International Nuclear Information System (INIS)

Zakharov, A.S.; Kirsanov, G.A.; Konoplev, K.A.

2005-01-01

Pin type fuel element (FE) of square form with twisted ribs was developed in VNIINM as an alternative for tube type FE of research reactors. Two variants of full-scale fuel assemblies (FA) are under test in the core of PNPI WWR-M reactor. One FA contains FE with UO 2 LEU and other - UMo LEU. Both types of FE have an aluminum matrix. Results of the first stages of the test are presented. (author)

A radiological consequence analysis with HEU and LEU fuels

International Nuclear Information System (INIS)

Woodruff, W.L.; Warinner, D.K.; Matos, J.E.

1985-01-01

A model for estimating the radiological consequences from a hypothetical accident in HEU and LEU fueled research and test reactors is presented. Simple hand calculations based on fission product yield table inventories and nonsite specific dispersion data may be adequate in many cases. However, more detailed inventories and site specific data on meteorological conditions and release rates and heights can result in substantial reductions in the dose estimates. LEU fuel gives essentially the same doses as HEU fuel. The plutonium buildup in the LEU fuel does not significantly increase the radiological consequences. The dose to the thyroid is the limiting dose. (author)

Development of whole core thermal-hydraulic analysis program ACT. 3. Coupling core module with primary heat transport system module

International Nuclear Information System (INIS)

Ohtaka, Masahiko; Ohshima, Hiroyuki

1998-10-01

A whole core thermal-hydraulic analysis program ACT is being developed for the purpose of evaluating detailed in-core thermal hydraulic phenomena of fast reactors including inter-wrapper flow under various reactor operation conditions. In this work, the core module as a main part of the ACT developed last year, which simulates thermal-hydraulics in the subassemblies and the inter-subassembly gaps, was coupled with an one dimensional plant system thermal-hydraulic analysis code LEDHER to simulate transients in the primary heat transport system and to give appropriate boundary conditions to the core model. The effective algorithm to couple these two calculation modules was developed, which required minimum modification of them. In order to couple these two calculation modules on the computing system, parallel computing technique using PVM (Parallel Virtual Machine) programming environment was applied. The code system was applied to analyze an out-of-pile sodium experiment simulating core with 7 subassemblies under transient condition for code verification. It was confirmed that the analytical results show a similar tendency of experimental results. (author)

FDTD analysis of body-core temperature elevation in children and adults for whole-body exposure

International Nuclear Information System (INIS)

Hirata, Akimasa; Asano, Takayuki; Fujiwara, Osamu

2008-01-01

The temperature elevations in anatomically based human phantoms of an adult and a 3-year-old child were calculated for radio-frequency whole-body exposure. Thermoregulation in children, however, has not yet been clarified. In the present study, we developed a computational thermal model of a child that is reasonable for simulating body-core temperature elevation. Comparison of measured and simulated temperatures revealed thermoregulation in children to be similar to that of adults. Based on this finding, we calculated the body-core temperature elevation in a 3-year-old child and an adult for plane-wave exposure at the basic restriction in the international guidelines. The body-core temperature elevation in the 3-year-old child phantom was 0.03 deg. C at a whole-body-averaged specific absorption rate of 0.08 W kg -1 , which was 35% smaller than in the adult female. This difference is attributed to the child's higher body surface area-to-mass ratio

FDTD analysis of body-core temperature elevation in children and adults for whole-body exposure

Energy Technology Data Exchange (ETDEWEB)

Hirata, Akimasa; Asano, Takayuki; Fujiwara, Osamu [Department of Computer Science and Engineering, Nagoya Institute of Technology (Japan)], E-mail: ahirata@nitech.ac.jp

2008-09-21

The temperature elevations in anatomically based human phantoms of an adult and a 3-year-old child were calculated for radio-frequency whole-body exposure. Thermoregulation in children, however, has not yet been clarified. In the present study, we developed a computational thermal model of a child that is reasonable for simulating body-core temperature elevation. Comparison of measured and simulated temperatures revealed thermoregulation in children to be similar to that of adults. Based on this finding, we calculated the body-core temperature elevation in a 3-year-old child and an adult for plane-wave exposure at the basic restriction in the international guidelines. The body-core temperature elevation in the 3-year-old child phantom was 0.03 deg. C at a whole-body-averaged specific absorption rate of 0.08 W kg{sup -1}, which was 35% smaller than in the adult female. This difference is attributed to the child's higher body surface area-to-mass ratio.

FDTD analysis of body-core temperature elevation in children and adults for whole-body exposure.

Science.gov (United States)

Hirata, Akimasa; Asano, Takayuki; Fujiwara, Osamu

2008-09-21

The temperature elevations in anatomically based human phantoms of an adult and a 3-year-old child were calculated for radio-frequency whole-body exposure. Thermoregulation in children, however, has not yet been clarified. In the present study, we developed a computational thermal model of a child that is reasonable for simulating body-core temperature elevation. Comparison of measured and simulated temperatures revealed thermoregulation in children to be similar to that of adults. Based on this finding, we calculated the body-core temperature elevation in a 3-year-old child and an adult for plane-wave exposure at the basic restriction in the international guidelines. The body-core temperature elevation in the 3-year-old child phantom was 0.03 degrees C at a whole-body-averaged specific absorption rate of 0.08 W kg(-1), which was 35% smaller than in the adult female. This difference is attributed to the child's higher body surface area-to-mass ratio.

[D-Leu-4]-OB3 and MA-[D-Leu-4]-OB3, small molecule synthetic peptide leptin mimetics, improve glycemic control in diet-induced obese (DIO) mice.

Science.gov (United States)

Wang, Anke; Anderson, Brian M; Novakovic, Zachary M; Grasso, Patricia

2018-03-01

We have previously shown that following oral delivery in dodecyl maltoside (DDM), [D-Leu-4]-OB3 and its myristic acid conjugate, MA-[D-Leu-4]-OB3, improved energy balance and glucose homeostasis in genetically obese/diabetic mouse models. More recently, we have provided immunohistochemical evidence indicating that these synthetic peptide leptin mimetics cross the blood-brain barrier and concentrate in the area of the arcuate nucleus of the hypothalamus in normal C57BL/6J and Swiss Webster mice, in genetically obese ob/ob mice, and in diet-induced obese (DIO) mice. In the present study, we describe the effects of oral delivery of [D-Leu-4]-OB3 and MA-[D-Leu-4]-OB3 on glycemic control in diet-induced (DIO) mice, a non-genetic rodent model of obesity and its associated insulin resistance, which more closely recapitulates common obesity and diabetes in humans. Male C57BL/6J and DIO mice, 17, 20, and 28 weeks of age, were maintained on a low-fat or high-fat diet and given vehicle (DDM) alone or [D-Leu-4]-OB3 or MA-[D-Leu-4]-OB3 in DDM by oral gavage for 12 or 14 days. Body weight gain, food and water intake, fasting blood glucose, oral glucose tolerance, and serum insulin levels were measured. Our data indicate that (1) [D-Leu-4]-OB3 and MA-[D-Leu-4]-OB3 restore glucose tolerance in male DIO mice maintained on a high-fat diet to levels comparable to those of non-obese C57BL/6J wild-type mice of the same age and sex maintained on a low-fat diet; and (2) the influence of [D-Leu-4]-OB3 and MA-[D-Leu-4]-OB3 on glycemic control appears to be independent of their effects on energy balance. These results suggest that [D-Leu-4]-OB3 and/or MA-[D-Leu-4]-OB3 may have application to the management of the majority of cases of common obesity in humans, a state characterized at least in part, by leptin resistance resulting from a defect in leptin transport across the blood-brain barrier. They further suggest that these small molecule synthetic peptide leptin mimetics, through their

South Africa and the RERTR programme. Current status. An AEC perspective

International Nuclear Information System (INIS)

Ball, G.

1999-01-01

The Atomic Energy Corporation (AEC) of South Africa fully endorses the principles of the RERTR programme. To this end in 1994 the AEC, together with Argonne National Laboratory (ANL), undertook a study into the feasibility of converting the SAFARI-1 reactor to LEU silicide fuel. More details are given. Due to the commercial pressures on the AEC at that time, the AEC decided not to convert SAFARI-1 to LEU silicide fuel. The AEC did, however, undertake to reevaluate the situation periodically. Five years have passed since the detailed study of 1994 and the changing conditions now warrant another detailed study taking into account the current situation. A brief historical background is given on the RERTR activities in South Africa since 1993 followed by a summary of the current situation

The Leakage Current Improvement of a Ni-Silicided SiGe/Si Junction Using a Si Cap Layer and the PAI Technique

International Nuclear Information System (INIS)

Chang Jian-Guang; Wu Chun-Bo; Ji Xiao-Li; Ma Hao-Wen; Yan Feng; Shi Yi; Zhang Rong

2012-01-01

We investigate the leakage current of ultra-shallow Ni-silicided SiGe/Si junctions for 45 nm CMOS technology using a Si cap layer and the pre-amorphization implantation (PAI) process. It is found that with the conventional Ni silicide method, the leakage current of a p + (SiGe)—n(Si) junction is large and attributed to band-to-band tunneling and the generation-recombination process. The two leakage contributors can be suppressed quite effectively when a Si cap layer is added in the Ni silicide method. The leakage reduction is about one order of magnitude and could be associated with the suppression of the agglomeration of the Ni germano-silicide film. In addition, the PAI process after the application of a Si cap layer has little effect on improving the junction leakage but reduces the sheet resistance of the silicide film. As a result, the novel Ni silicide method using a Si cap combined with PAI is a promising choice for SiGe junctions in advanced technology. (cross-disciplinary physics and related areas of science and technology)

Prospects in deterministic three dimensional whole-core transport calculations

International Nuclear Information System (INIS)

Sanchez, Richard

2012-01-01

The point we made in this paper is that, although detailed and precise three-dimensional (3D) whole-core transport calculations may be obtained in the future with massively parallel computers, they would have an application to only some of the problems of the nuclear industry, more precisely those regarding multiphysics or for methodology validation or nuclear safety calculations. On the other hand, typical design reactor cycle calculations comprising many one-point core calculations can have very strict constraints in computing time and will not directly benefit from the advances in computations in large scale computers. Consequently, in this paper we review some of the deterministic 3D transport methods which in the very near future may have potential for industrial applications and, even with low-order approximations such as a low resolution in energy, might represent an advantage as compared with present industrial methodology, for which one of the main approximations is due to power reconstruction. These methods comprise the response-matrix method and methods based on the two-dimensional (2D) method of characteristics, such as the fusion method.

HEU to LEU conversion and blending facility: Metal blending alternative to produce LEU oxide for disposal

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-09-01

US DOE is examining options for disposing of surplus weapons-usable fissile materials and storage of all weapons-usable fissile materials. The nuclear material is converted to a form more proliferation- resistant than the original form. Blending HEU (highly enriched uranium) with less-enriched uranium to form LEU has been proposed as a disposition option. Five technologies are being assessed for blending HEU. This document provides data to be used in environmental impact analysis for the HEU-LEU disposition option that uses metal blending with an oxide waste product. It is divided into: mission and assumptions, conversion and blending facility descriptions, process descriptions and requirements, resource needs, employment needs, waste and emissions from plant, hazards discussion, and intersite transportation.

HEU to LEU conversion and blending facility: Metal blending alternative to produce LEU oxide for disposal

International Nuclear Information System (INIS)

1995-09-01

US DOE is examining options for disposing of surplus weapons-usable fissile materials and storage of all weapons-usable fissile materials. The nuclear material is converted to a form more proliferation- resistant than the original form. Blending HEU (highly enriched uranium) with less-enriched uranium to form LEU has been proposed as a disposition option. Five technologies are being assessed for blending HEU. This document provides data to be used in environmental impact analysis for the HEU-LEU disposition option that uses metal blending with an oxide waste product. It is divided into: mission and assumptions, conversion and blending facility descriptions, process descriptions and requirements, resource needs, employment needs, waste and emissions from plant, hazards discussion, and intersite transportation

Preproghrelin Leu72Met polymorphism in obese Korean children.

Science.gov (United States)

Jo, Dae-Sun; Kim, Se-Lim; Kim, Sun-Young; Hwang, Pyoung Han; Lee, Kee-Hyoung; Lee, Dae-Yeol

2005-11-01

Ghrelin is a novel gut-brain peptide that has somatotropic, orexigenic, and adipogenic effects. We examined the preproghrelin Leu72Met polymorphism in 222 obese Korean children to determine whether it is associated with obesity. The frequencies of the Leu72Met polymorphism were 29.3% in obese, 32.3% in overweight, and 32.5% in lean Korean children. No significant difference was found between Met72 carrier and non-carrier obese children with respect to BMI, total body fat, serum triglycerides, total cholesterol, or LDL-cholesterol levels. Our data suggest that the preproghrelin Leu72Met polymorphism is not associated with obesity in children.

Analysis of hypothetical LMFBR whole-core accidents in the USA

International Nuclear Information System (INIS)

Ferguson, D.R.; Deitrich, L.W.; Brown, N.W.; Waltar, A.E.

1978-01-01

The issue of hypothetical whole-core accidents continues to play a significant role in assessment of the potential risk to the public associated with LMFBR operation in the USA. The paper briefly characterizes the changing nature of this role, with emphasis on the current risk-oriented perspective. It then describes the models and codes used for accident analysis in the USA which have been developed under DOE sponsorship and summarizes some specific applications of the codes to the current generation of fast reactors. An assessment of future trends in this area concludes the paper

The manufacture of LEU fuel elements at Dounreay

Energy Technology Data Exchange (ETDEWEB)

Gibson, J.

1997-08-01

Two LEU test elements are being manufactured at Dounreay for test irradiation in the HFR at Petten, The Netherlands. This paper describes the installation of equipment and the development of the fabrication and inspection techniques necessary for the manufacture of LEU fuel plates. The author`s experience in overcoming the technical problems of stray fuel particles, dog-boning, uranium homogeneity and the measurement of uranium distribution is also described.

Kinetics of low pressure chemical vapor deposition of tungsten silicide from dichlorocilane reduction of tungsten hexafluoride

International Nuclear Information System (INIS)

Srinivas, D.; Raupp, G.B.; Hillman, J.

1990-01-01

The authors report on experiments to determine the intrinsic surface reaction rate dependences and film properties' dependence on local reactant partial pressures and wafer temperature in low pressure chemical vapor deposition (LPCVD) of tungsten silicide from dichlorosilane reduction of tungsten hexafluoride. Films were deposited in a commercial-scale Spectrum CVD cold wall single wafer reactor under near differential, gradientless conditions. Over the range of process conditions investigated, deposition rate was found to be first order in dichlorosillane and negative second order in tungsten hexafluoride partial pressure. The apparent activation energy in the surface reaction limited regime was found to be 70-120 kcal/mol. The silicon to tungsten ratio of as deposited silicide films ranged from 1.1 to 2.4, and increased with increasing temperature and dichlorosillane partial pressure, and decreased with increasing tungsten hexafluoride pressure. These results suggest that the apparent silicide deposition rate and composition are controlled by the relative rates of at least two competing reactions which deposit stoichiometric tungsten silicides and/or silicon

Total synthesis of fully tritiated Leu-enkephalin by enzymatic coupling

Energy Technology Data Exchange (ETDEWEB)

Hellio, F.; Lecocq, G.; Morgat, J.L.; Gueguen, P. (CEA Centre d' Etudes Nucleaires de Saclay, 91 - Gif-sur-Yvette (France). Service de Biochimie)

1990-09-01

This paper describes the total enzymatic synthesis of Leu-enkephalin (Tyr-Gly-Gly-Phe-Leu) in which all residues were labelled with tritium. Carboxypeptidase Y from Saccharomyces cerevisiae was the coupling enzyme. ({sup 3}H)-Tyr-NH{sub 2}, ({sup 3}H)-Gly-Oet, ({sup 3}H)-Phe-NH{sub 2} and ({sup 3}H)-Leu-NH{sub 2} were prepared with specific radioactivities ranging between 20 and 60 Ci/mmol (740 to 2220 GBq/mmol). Using a microscale procedure, we obtained a fully tritiated hormone having a specific radioactivity equal to 139 Ci/mmol (5143 GBq/mmol), in agreement with the summation of the specific radioactivities of constituting residue. The radioactive hormone had antigenic properties identical to those of native Leu-enkephalin. It also bound to rat brain opiate receptors like the parental hormone. (author).

Preproghrelin Leu72Met polymorphism in patients with type 2 diabetes mellitus.

Science.gov (United States)

Ukkola, O; Kesäniemi, Y A

2003-10-01

The association between the Leu72Met polymorphism of the preproghrelin gene and diabetic complications was examined in patients with type 2 diabetes mellitus. A total of 258 patients with type 2 diabetes mellitus and 522 control subjects were screened. Genotypes were determined by polymerase chain reaction technique. The diagnosis of coronary heart disease was based on clinical and ECG criteria. Laboratory analyses were carried out in the hospital laboratory. No differences in the genotype distributions and allele frequencies of the preproghrelin Leu72Met polymorphism were found between type 2 diabetes mellitus patients and controls. The polymorphism was not associated with macro- or micro-angiopathy or hypertension. However, Leu72Met polymorphism was associated with serum creatinine (P = 0.006) and lipoprotein(a) [Lp(a)] levels (P = 0.006) with Leu72Leu subjects showing the highest values. This association was observed only amongst diabetic group. The Leu72Met polymorphism of the preproghrelin gene was not related to cardiovascular disease in type 2 diabetes mellitus patients. Leu72Met polymorphism was, however, associated with serum creatinine and Lp(a) levels in diabetic patients. The mechanism might be associated with a possible change in ghrelin product and its somatotropic effect.

Pressure effect on the conformational equilibrium of [Leu]{sup 5}-enkephalin in water

Energy Technology Data Exchange (ETDEWEB)

Shimizu, A [Department of Environmental Engineering for Symbiosis, Soka University, 1-326 Tangi-cho, Hachioji, Tokyo, 192-8577 (Japan); Takekiyo, T; Yoshimura, Y [Department of Applied Chemistry, National Defence Academy, 1-10-20 Hashirimizu, Yokosuka, Kanagawa, 239-8686 (Japan); Kato, M; Taniguchi, Y, E-mail: shimizu@soka.ac.j, E-mail: take214@nda.ac.j [Department of Applied Chemistry, Ritsumeikan University, 1-1-1, Nojihigashi, Kusatsu, Shiga, 525-8577 (Japan)

2010-03-01

The conformational stability of [Leu]{sup 5}-enkephalin,Tyr-Gly-Gly-Phe-Leu, in water have been investigated under high pressure by FTIR spectroscopy. Three peaks at 1638, 1650, and 1680 cm{sup -1} were determined by second derivative FTIR spectra in the amide I' region of [Leu]{sup 5}-enkephalin. The peaks at 1637 and 1680 cm{sup -1} are assigned to the {beta}-strand and turn structures, respectively. These peaks mean that [Leu]{sup 5}-enkephalin takes a {beta}-hairpin-like structure in water. Moreover, the absorbance at 1638 cm{sup -1} increases with increasing pressure, and this change shows a sigmoidal curve. Thus, we concluded that [Leu]{sup 5}-enkephalin has the {beta}-hairpin-like and disordered structures in water. From the FTIR profile at high pressures, the {beta}-hairpin-like structure of [Leu]{sup 5}-enkephalin is stabilized by a high pressures. Our result shows that the folded structures such as {alpha}-helix and {beta}-hairpin structures of short peptide such as [Leu]{sup 5}-enkephalin are stabilized at high pressures.

Tungsten silicide contacts to polycrystalline silicon and silicon-germanium alloys

International Nuclear Information System (INIS)

Srinivasan, G.; Bain, M.F.; Bhattacharyya, S.; Baine, P.; Armstrong, B.M.; Gamble, H.S.; McNeill, D.W.

2004-01-01

Silicon-germanium alloy layers will be employed in the source-drain engineering of future MOS transistors. The use of this technology offers advantages in reducing series resistance and decreasing junction depth resulting in reduction in punch-through and SCE problems. The contact resistance of metal or metal silicides to the raised source-drain material is a serious issue at sub-micron dimensions and must be minimised. In this work, tungsten silicide produced by chemical vapour deposition has been investigated as a contact metallization scheme to both boron and phosphorus doped polycrystalline Si 1- x Ge x , with 0 ≤x ≤ 0.3. Cross bridge Kelvin resistor (CKBR) structures were fabricated incorporating CVD WSi 2 and polycrystalline SiGe. Tungsten silicide contacts to control polysilicon CKBR structures have been shown to be of high quality with specific contact resistance ρ c values 3 x 10 -7 ohm cm 2 and 6 x 10 -7 ohm cm 2 obtained to boron and phosphorus implanted samples respectively. The SiGe CKBR structures show that the inclusion of Ge yields a reduction in ρ c for both dopant types. The boron doped SiGe exhibits a reduction in ρ c from 3 x 10 -7 to 5 x 10 -8 ohm cm 2 as Ge fraction is increased from 0 to 0.3. The reduction in ρ c has been shown to be due to (i) the lowering of the tungsten silicide Schottky barrier height to p-type SiGe resulting from the energy band gap reduction, and (ii) increased activation of the implanted boron with increased Ge fraction. The phosphorus implanted samples show less sensitivity of ρ c to Ge fraction with a lowest value in this work of 3 x 10 -7 ohm cm 2 for a Ge fraction of 0.3. The reduction in specific contact resistance to the phosphorus implanted samples has been shown to be due to increased dopant activation alone

Behavior of silicon in nitric media. Application to uranium silicides fuels reprocessing; Comportement du silicium en milieu nitrique. Application au retraitement des combustibles siliciures d'uranium

Energy Technology Data Exchange (ETDEWEB)

Cheroux, L

2001-07-01

Uranium silicides are used in some research reactors. Reprocessing them is a solution for their cycle end. A list of reprocessing scenarios has been set the most realistic being a nitric dissolution close to the classic spent fuel reprocessing. This uranium silicide fuel contains a lot of silicon and few things are known about polymerization of silicic acid in concentrated nitric acid. The study of this polymerization allows to point out the main parameters: acidity, temperature, silicon concentration. The presence of aluminum seems to speed up heavily the polymerization. It has been impossible to find an analytical technique smart and fast enough to characterize the first steps of silicic acid polymerization. However the action of silicic species on emulsions stabilization formed by mixing them with an organic phase containing TBP has been studied, Silicon slows down the phase separation by means of oligomeric species forming complex with TBP. The existence of these intermediate species is short and heating can avoid any stabilization. When non irradiated uranium silicide fuel is attacked by a nitric solution, aluminum and uranium are quickly dissolved whereas silicon mainly stands in solid state. That builds a gangue of hydrated silica around the uranium silicide particulates without preventing uranium dissolution. A small part of silicon passes into the solution and polymerize towards the highly poly-condensed forms, just 2% of initial silicon is still in molecular form at the end of the dissolution. A thermal treatment of the fuel element, by forming inter-metallic phases U-Al-Si, allows the whole silicon to pass into the solution and next to precipitate. The behavior of silicon in spent fuels should be between these two situations. (author)

Whole-body cryostimulation increases parasympathetic outflow and decreases core body temperature.

Science.gov (United States)

Zalewski, Pawel; Bitner, Anna; Słomko, Joanna; Szrajda, Justyna; Klawe, Jacek J; Tafil-Klawe, Malgorzata; Newton, Julia L

2014-10-01

The cardiovascular, autonomic and thermal response to whole-body cryostimulation exposure are not completely known. Thus the aim of this study was to evaluate objectively and noninvasively autonomic and thermal reactions observed after short exposure to very low temperatures. We examined 25 healthy men with mean age 30.1 ± 3.7 years and comparable anthropomorphical characteristic. Each subject was exposed to cryotherapeutic temperatures in a cryogenic chamber for 3 min (approx. -120 °C). The cardiovascular and autonomic parameters were measured noninvasively with Task Force Monitor. The changes in core body temperature were determined with the Vital Sense telemetric measurement system. Results show that 3 min to cryotherapeutic temperatures causes significant changes in autonomic balance which are induced by peripheral and central blood volume changes. Cryostimulation also induced changes in core body temperature, maximum drop of core temperature was observed 50-60 min after the stimulation. Autonomic and thermal reactions to cryostimulation were observed up to 6 h after the exposure and were not harmful for examined subjects. Copyright © 2014 Elsevier Ltd. All rights reserved.

Interfacing high-fidelity core neutronics models to whole plant models

International Nuclear Information System (INIS)

McEllin, M.

1999-01-01

Until recently available computer power dictated that whole-plant models of nuclear power stations have typically employed simple models of the reactor core which can not match the fidelity of safety-qualified 2-group, 3D neutronics models. As a result the treatment of situations involving strong coupling between the core and the rest of the plant has inevitably been somewhat approximate, requiring conservative modelling assumptions, or manual iteration between cases, to bound worse case scenarios. Such techniques not only place heavy demands on the engineers involved, they may also result in potentially unnecessary operational constraints. Hardware is today no longer the limiting factor, but the cost of developing and validating high-quality software is now such that it appears attractive to build new systems with a wider simulation scope by using existing stand-alone codes as sub-components. This is not always as straightforward as it might at first appear. This paper illustrates some of the pitfalls, and discusses more sophisticated and robust strategies. (author)

Formation of copper silicides by high dose metal vapor vacuum arc ion implantation

International Nuclear Information System (INIS)

Rong Chun; Zhang Jizhong; Li Wenzhi

2003-01-01

Si(1 1 1) was implanted by copper ions with different doses and copper distribution in silicon matrix was obtained. The as-implanted samples were annealed at 300 and 540 deg. C, respectively. Formation of copper silicides in as-implanted and annealed samples were studied. Thermodynamics and kinetics of the reaction were found to be different from reaction at copper-silicon interface that was applied in conventional studies of copper-silicon interaction. The defects in silicon induced by implantation and formation of copper silicides were recognized by Si(2 2 2) X-ray diffraction (XRD)

Progress in chemical processing of LEU targets for 99Mo production - 1997

International Nuclear Information System (INIS)

Vandegrift, G.F.; Conner, C.; Sedlet, J.; Wygmans, D.G.; Wu, D.; Iskander, F.; Landsberger, S.

1997-01-01

Presented here are recent experimental results of our continuing development activities associated with converting current processes for producing fission-product 99 Mo from targets using high-enriched uranium (HEU) to low-enriched uranium (LEU). Studies were focused in four areas: (1) measuring the chemical behavior of iodine, rhodium, and silver in the LEU-modified Cintichem process, (2) performing experiments and calculations to assess the suitability of zinc fission barriers for LEU metal foil targets, (3) developing an actinide separations method for measuring alpha contamination of the purified 99 Mo product, and (4) developing a cooperation with Sandia National Laboratories and Los Alamos National Laboratory that will lead to approval by the U.S. Federal Drug Administration for production of 99 Mo from LEU targets. Experimental results continue to show the technical feasibility of converting current HEU processes to LEU. (author)

High temperature structural silicides

International Nuclear Information System (INIS)

Petrovic, J.J.

1997-01-01

Structural silicides have important high temperature applications in oxidizing and aggressive environments. Most prominent are MoSi 2 -based materials, which are borderline ceramic-intermetallic compounds. MoSi 2 single crystals exhibit macroscopic compressive ductility at temperatures below room temperature in some orientations. Polycrystalline MoSi 2 possesses elevated temperature creep behavior which is highly sensitive to grain size. MoSi 2 -Si 3 N 4 composites show an important combination of oxidation resistance, creep resistance, and low temperature fracture toughness. Current potential applications of MoSi 2 -based materials include furnace heating elements, molten metal lances, industrial gas burners, aerospace turbine engine components, diesel engine glow plugs, and materials for glass processing

Local solid phase growth of few-layer graphene on silicon carbide from nickel silicide supersaturated with carbon

International Nuclear Information System (INIS)

Escobedo-Cousin, Enrique; Vassilevski, Konstantin; Hopf, Toby; Wright, Nick; O'Neill, Anthony; Horsfall, Alton; Goss, Jonathan; Cumpson, Peter

2013-01-01

Patterned few-layer graphene (FLG) films were obtained by local solid phase growth from nickel silicide supersaturated with carbon, following a fabrication scheme, which allows the formation of self-aligned ohmic contacts on FLG and is compatible with conventional SiC device processing methods. The process was realised by the deposition and patterning of thin Ni films on semi-insulating 6H-SiC wafers followed by annealing and the selective removal of the resulting nickel silicide by wet chemistry. Raman spectroscopy and X-ray photoelectron spectroscopy (XPS) were used to confirm both the formation and subsequent removal of nickel silicide. The impact of process parameters such as the thickness of the initial Ni layer, annealing temperature, and cooling rates on the FLG films was assessed by Raman spectroscopy, XPS, and atomic force microscopy. The thickness of the final FLG film estimated from the Raman spectra varied from 1 to 4 monolayers for initial Ni layers between 3 and 20 nm thick. Self-aligned contacts were formed on these patterned films by contact photolithography and wet etching of nickel silicide, which enabled the fabrication of test structures to measure the carrier concentration and mobility in the FLG films. A simple model of diffusion-driven solid phase chemical reaction was used to explain formation of the FLG film at the interface between nickel silicide and silicon carbide.

Evaluation of core physics analysis methods for conversion of the INL advanced test reactor to low-enrichment fuel

International Nuclear Information System (INIS)

DeHart, M. D.; Chang, G. S.

2012-01-01

Computational neutronics studies to support the possible conversion of the ATR to LEU are underway. Simultaneously, INL is engaged in a physics methods upgrade project to put into place modern computational neutronics tools for future support of ATR fuel cycle and experiment analysis. A number of experimental measurements have been performed in the ATRC in support of the methods upgrade project, and are being used to validate the new core physics methods. The current computational neutronics work is focused on performance of scoping calculations for the ATR core loaded with a candidate LEU fuel design. This will serve as independent confirmation of analyses that have been performed previously, and will evaluate some of the new computational methods for analysis of a candidate LEU fuel for ATR. (authors)

Conversion, core redesign and upgrade of the Rhode Island Atomic Energy Commission Reactor

International Nuclear Information System (INIS)

DiMeglio, A.F.

1987-01-01

The 2 MW Rhode Island Atomic Energy Commission reactor is required to convert from the use of High Enriched Uranium (HEU) fuel to the use of Low Enriched Uranium (LEU) fuel using a standard LEU fuel plate which is thinner and contains more Uranium-235 than the current HEU plate. These differences, coupled with the fact that the conversion should be accomplished without serious degradation of reactor characteristics and capability, has resulted in core design studies and thermal hydraulic studies not only at the current 2 MW but also at the maximum power level of the reactor, 5 MW. In addition, during the course of its 23 years of operation, it has become clear that the main uses of the reactor are neutron scattering and neutron activation analysis. The requirement to convert to LEU presents an opportunity during the conversion to optimize the core for the utilization and to restudy the thermal hydraulics using modern techniques. This paper will present the preliminary conclusions of both aspects. (Author)

Information for irradiation and post-irradiation of the silicide fuel element prototype P-07

International Nuclear Information System (INIS)

Abbate, Maximo J.; Sbaffoni, Maria M.

2003-01-01

Included in the 'Silicides' Project, developed by the Nuclear Fuels Department of the National Atomic Energy Commission (CNEA), it is foreseen the qualification of this type of fuel for research reactors in order to be used in the Argentine RA-3 reactor and to confirm the CNEA as an international supplier. The paper presents basic information on several parameters corresponding to the new silicide prototype, called P-07, to be taken into account for its irradiation, postirradiation and qualification. (author)

Application of the successive linear programming technique to the optimum design of a high flux reactor using LEU fuel

International Nuclear Information System (INIS)

Mo, S.C.

1991-01-01

The successive linear programming technique is applied to obtain the optimum thermal flux in the reflector region of a high flux reactor using LEU fuel. The design variables are the reactor power, core radius and coolant channel thickness. The constraints are the cycle length, average heat flux and peak/average power density ratio. The characteristics of the optimum solutions with various constraints are discussed

Preproghrelin Leu72Met polymorphism in Chinese subjects with coronary artery disease and controls.

Science.gov (United States)

Tang, Na-Ping; Wang, Lian-Sheng; Yang, Li; Gu, Hai-Juan; Zhu, Huai-Jun; Zhou, Bo; Sun, Qing-Min; Cong, Ri-Hong; Wang, Bin

2008-01-01

Ghrelin, a novel endogenous ligand for the growth hormone secretagogue receptor, is considered to exert a protective effect against atherosclerosis. The Leu72Met (+408C>A) polymorphic variant of the preproghrelin, the gene for the ghrelin precursor, has been linked to obesity, diabetes and metabolic syndrome. However, it is unclear whether this polymorphism is associated with coronary artery disease (CAD). We conducted a case-control study with 317 CAD patients and 323 controls to investigate the potential association of the Leu72Met polymorphism with the occurrence of CAD and CAD-related phenotypes in Chinese population. No significant difference in the Leu72Met genotype frequency was observed between CAD patients and controls (P=NS). The Leu72Met polymorphism was not associated with hypertension, diabetes, dyslipidemia, the number of diseased vessels, plasma total cholesterol, triglyceride, high density lipoprotein cholesterol, low density lipoprotein cholesterol or fasting glucose levels in CAD patients. However, among CAD patients, those with variant genotypes (Leu72Met and Met72Met) had lower BMI (24.4+/-0.3 kg/m(2)) than Leu72Leu carriers (25.4+/-0.2 kg/m(2), adjusted P=0.033). Our data indicate that the preproghrelin Leu72Met polymorphism is not associated with CAD in Chinese population. However, the Leu72Met variant is associated with BMI among CAD patients.

Genetic interaction between the ero1-1 and leu2 mutations in Saccharomyces cerevisiae

DEFF Research Database (Denmark)

López-Mirabal, H Reynaldo; Winther, Jakob R; Kielland-Brandt, Morten C

2007-01-01

of the ero1-1 mutation were carried out in a leu2 mutant. The ero1-1 leu2 strain does not grow in standard synthetic complete medium at 30 degrees C, a defect that can be remedied by increasing the L-leucine concentration in the medium or by transforming the ero1-1 leu2 strain with the LEU2 wild-type allele...

Formation of (Nd,Y)-silicides by sequential channeled implantation of Y and Nd ions

International Nuclear Information System (INIS)

Jin, S.; Bender, H.; Wu, M.F.; Vantomme, A.; Langouche, G.

2000-01-01

A buried hexagonal Nd 0.32 Y 0.68 Si 1.7 layer is formed by a sequential implantation of Y and Nd ions into (1 1 1)-oriented silicon wafers. The orientation relationship between the epitaxial Nd 0.32 Y 0.68 Si 1.7 and the silicon is (0 0 0 1) Nd 0.32 Y 0.68 Si 1.7 //(1 1 1) Si with Nd 0.32 Y 0.68 Si 1.7 // Si . High temperature annealing (1000 deg. C) results in a gradual transition into an orthorhombic ternary (Nd,Y)-silicide. Between the orthorhombic (Nd,Y)-silicide and the Si a preferential orientation relationship exists: (1 1 0) orth //(1 1(bar) 0) Si with orth // Si . However, as not all orthorhombic silicide grains follow this epitaxial relationship, the minimum yield in the Rutherford backscattering spectrometry (RBS) spectrum increases compared to the results after a low temperature annealing

Formation of (Nd,Y)-silicides by sequential channeled implantation of Y and Nd ions

Science.gov (United States)

Jin, S.; Bender, H.; Wu, M. F.; Vantomme, A.; Langouche, G.

2000-03-01

A buried hexagonal Nd0.32Y0.68Si1.7 layer is formed by a sequential implantation of Y and Nd ions into (1 1 1)-oriented silicon wafers. The orientation relationship between the epitaxial Nd0.32Y0.68Si1.7 and the silicon is (0 0 0 1)Nd0.32Y0.68Si1.7//(1 1 1)Si with Nd0.32Y0.68Si1.7//Si. High temperature annealing (1000°C) results in a gradual transition into an orthorhombic ternary (Nd,Y)-silicide. Between the orthorhombic (Nd,Y)-silicide and the Si a preferential orientation relationship exists: (1 1 0)orth//(1 1¯ 0)Si with orth//Si. However, as not all orthorhombic silicide grains follow this epitaxial relationship, the minimum yield in the Rutherford backscattering spectrometry (RBS) spectrum increases compared to the results after a low temperature annealing.

LEU-HTR critical experiment program for the PROTEUS facility in Switzerland

International Nuclear Information System (INIS)

Brogli, R.; Bucher, K.H.; Chawla, R.; Foskolos, K.; Luchsinger, H.; Mathews, D.; Sarlos, G.; Seiler, R.

1990-01-01

New critical experiments in the framework of an IAEA Coordinated Research Program on 'Validation of Safety Related Reactor Physics Calculations for Low Enriched HTRs' are planned at the PSI PROTEUS facility. The experiments are designed to supplement the experimental data base and reduce the design and licensing uncertainties for small- and medium-sized helium-cooled reactors using low-enriched uranium (LEU) and graphite high temperature fuel. The main objectives of the new experiments are to provide first-of-a-kind high quality experimental data on: 1) The criticality of simple, easy to interpret, single core region LEU HTR systems for several moderator-to-fuel ratios and several lattice geometries; 2) the changes in reactivity, neutron balance components and control rod effectiveness caused by water ingress into this type of reactor, and 3) the effects of the boron and/or hafnium absorbers that are used to modify the reactivity and the power distributions in typical HTR systems. Work on the design and licensing of the modified PROTEUS critical facility is now in progress with the HTR experiments scheduled to begin early in 1991. Several international partners will be involved in the planning, execution and analysis of these experiments in order to insure that they are relevant and cost effective with respect to the various gas cooled reactor national programs. (author)

LEU-HTR critical experiment program for the PROTEUS facility in Switzerland

Energy Technology Data Exchange (ETDEWEB)

Brogli, R; Bucher, K H; Chawla, R; Foskolos, K; Luchsinger, H; Mathews, D; Sarlos, G; Seiler, R [Paul Scherrer Institute, Laboratory for Reactor Physics and System Technology Wuerenlingen and Villigen, Villigen PSI (Switzerland)

1990-07-01

New critical experiments in the framework of an IAEA Coordinated Research Program on 'Validation of Safety Related Reactor Physics Calculations for Low Enriched HTRs' are planned at the PSI PROTEUS facility. The experiments are designed to supplement the experimental data base and reduce the design and licensing uncertainties for small- and medium-sized helium-cooled reactors using low-enriched uranium (LEU) and graphite high temperature fuel. The main objectives of the new experiments are to provide first-of-a-kind high quality experimental data on: 1) The criticality of simple, easy to interpret, single core region LEU HTR systems for several moderator-to-fuel ratios and several lattice geometries; 2) the changes in reactivity, neutron balance components and control rod effectiveness caused by water ingress into this type of reactor, and 3) the effects of the boron and/or hafnium absorbers that are used to modify the reactivity and the power distributions in typical HTR systems. Work on the design and licensing of the modified PROTEUS critical facility is now in progress with the HTR experiments scheduled to begin early in 1991. Several international partners will be involved in the planning, execution and analysis of these experiments in order to insure that they are relevant and cost effective with respect to the various gas cooled reactor national programs. (author)

Fracture of niobium-base silicide coated alloy

International Nuclear Information System (INIS)

Davydova, A.D.; Zotov, Yu.P.; Ivashchenko, O.V.; Kushnareva, N.P.; Yarosh, I.P.

1990-01-01

Mechanical properties and character of fracture of Nb-W-Mo-Zr-C alloy composition with complex by composition and structure silicide coating under different states of stage-by-stage coating are studied. Structural features, character of fracture from ductile to quasibrittle transcrystalline one and, respectively, the composition plasticity level are defined by interrelation of fracture processes in coating, matrix plastic flow and possibility and way of stress relaxation on their boundary

Technical basis in support of the conversion of the University of Missouri Research Reactor (MURR) core from highly-enriched to low-enriched uranium - core neutron physics

Energy Technology Data Exchange (ETDEWEB)

Stillman, J. [Argonne National Lab. (ANL), Argonne, IL (United States); Feldman, E. [Univ. of Missouri, Columbia, MO (United States). Columbia Research Reactor; Foyto, L [Univ. of Missouri, Columbia, MO (United States). Columbia Research Reactor; Kutikkad, K [Univ. of Missouri, Columbia, MO (United States). Columbia Research Reactor; McKibben, J C [Univ. of Missouri, Columbia, MO (United States). Columbia Research Reactor; Peters, N. [Univ. of Missouri, Columbia, MO (United States). Columbia Research Reactor; Stevens, J. [Argonne National Lab. (ANL), Argonne, IL (United States)

2012-09-01

This report contains the results of reactor design and performance for conversion of the University of Missouri Research Reactor (MURR) from the use of highly-enriched uranium (HEU) fuel to the use of low-enriched uranium (LEU) fuel. The analyses were performed by staff members of the Global Threat Reduction Initiative (GTRI) Reactor Conversion Program at the Argonne National Laboratory (ANL) and the MURR Facility. The core conversion to LEU is being performed with financial support of the U. S. government.

HEU benchmark calculations and LEU preliminary calculations for IRR-1

International Nuclear Information System (INIS)

Caner, M.; Shapira, M.; Bettan, M.; Nagler, A.; Gilat, J.

2004-01-01

We performed neutronics calculations for the Soreq Research Reactor, IRR-1. The calculations were done for the purpose of upgrading and benchmarking our codes and methods. The codes used were mainly WIMS-D/4 for cell calculations and the three dimensional diffusion code CITATION for full core calculations. The experimental flux was obtained by gold wire activation methods and compared with our calculated flux profile. The IRR-1 is loaded with highly enriched uranium fuel assemblies, of the plate type. In the framework of preparation for conversion to low enrichment fuel, additional calculations were done assuming the presence of LEU fresh fuel. In these preliminary calculations we investigated the effect on the criticality and flux distributions of the increase of U-238 loading, and the corresponding uranium density.(author)

Substrate-modulated unwinding of transmembrane helices in the NSS transporter LeuT.

Science.gov (United States)

Merkle, Patrick S; Gotfryd, Kamil; Cuendet, Michel A; Leth-Espensen, Katrine Z; Gether, Ulrik; Loland, Claus J; Rand, Kasper D

2018-05-01

LeuT, a prokaryotic member of the neurotransmitter:sodium symporter (NSS) family, is an established structural model for mammalian NSS counterparts. We investigate the substrate translocation mechanism of LeuT by measuring the solution-phase structural dynamics of the transporter in distinct functional states by hydrogen/deuterium exchange mass spectrometry (HDX-MS). Our HDX-MS data pinpoint LeuT segments involved in substrate transport and reveal for the first time a comprehensive and detailed view of the dynamics associated with transition of the transporter between outward- and inward-facing configurations in a Na + - and K + -dependent manner. The results suggest that partial unwinding of transmembrane helices 1/5/6/7 drives LeuT from a substrate-bound, outward-facing occluded conformation toward an inward-facing open state. These hitherto unknown, large-scale conformational changes in functionally important transmembrane segments, observed for LeuT in detergent-solubilized form and when embedded in a native-like phospholipid bilayer, could be of physiological relevance for the translocation process.

Solvent extraction studies of RERTR silicide fuels

International Nuclear Information System (INIS)

Gouge, Anthony P.

1983-01-01

Uranium silicide fuels, which are candidate RERTR fuel compositions, may require special considerations in solvent extraction reprocessing. Since Savannah River Plant may be reprocessing RERTR fuels as early as 1985, studies have been conducted at Savannah River Laboratory to demonstrate the solvent extraction behavior of this fuel. Results of solvent extraction studies with both unirradiated and irradiated fuel are presented along with the preliminary RERTR solvent extraction reprocessing flow sheet for Savannah River Plant. (author)

Phase transformations in Higher Manganese Silicides

Energy Technology Data Exchange (ETDEWEB)

Allam, A. [MADIREL, UMR 7246 CNRS - Universite Aix-Marseille, av Normandie-Niemen, 13397 Marseille Cedex 20 (France); IM2NP, UMR 7334 CNRS - Universite Aix-Marseille, av Normandie-Niemen, Case 142, 13397 Marseille Cedex 20 (France); Boulet, P. [MADIREL, UMR 7246 CNRS - Universite Aix-Marseille, av Normandie-Niemen, 13397 Marseille Cedex 20 (France); Nunes, C.A. [Departamento de Engenharia de Materiais (DEMAR), Escola de Engenharia de Lorena (EEL), Universidade de Sao Paulo - USP, Caixa Postal 116, 12600-970 Lorena, Sao Paulo (Brazil); Sopousek, J.; Broz, P. [Masaryk University, Faculty of Science, Department of Chemistry, Kolarska 2, 611 37 Brno (Czech Republic); Masaryk University, Central European Institute of Technology, CEITEC, Kamenice 753/5, 625 00 Brno (Czech Republic); Record, M.-C., E-mail: m-c.record@univ-cezanne.fr [IM2NP, UMR 7334 CNRS - Universite Aix-Marseille, av Normandie-Niemen, Case 142, 13397 Marseille Cedex 20 (France)

2013-02-25

Highlights: Black-Right-Pointing-Pointer The phase transitions of the Higher Manganese Silicides were investigated. Black-Right-Pointing-Pointer The samples were characterised by XRD, DTA and DSC. Black-Right-Pointing-Pointer Mn{sub 27}Si{sub 47} is the stable phase at room temperature and under atmospheric pressure. Black-Right-Pointing-Pointer At around 800 Degree-Sign C, Mn{sub 27}Si{sub 47} is transformed into Mn{sub 15}Si{sub 26}. Black-Right-Pointing-Pointer The phase transition is of a second order. - Abstract: This work is an investigation of the phase transformations of the Higher Manganese Silicides in the temperature range [100-1200 Degree-Sign C]. Several complementary experimental techniques were used, namely in situ X-ray Diffraction (XRD), Differential Thermal Analysis (DTA) and Differential Scanning Calorimetry (DSC). The evolution of both the lattice parameters and the thermal expansion coefficients was determined from in situ XRD measurements. The stability of the samples was investigated by thermal analysis (DTA) and Cp measurements (DSC). This study shows that Mn{sub 27}Si{sub 47} which is the stable phase at room temperature and under atmospheric pressure undergoes a phase transformation at around 800 Degree-Sign C. Mn{sub 27}Si{sub 47} is transformed into Mn{sub 15}Si{sub 26}. This phase transformation seems to be of a second order one. Indeed it was not evidenced by DTA and by contrast it appears on the Cp curve.

The electronic structure of 4d and 5d silicides

NARCIS (Netherlands)

Speier, W.; Kumar, L.; Sarma, D.D.; Groot, R.A. de; Fuggle, J.C.

1989-01-01

A systematic experimental and theoretical study of the electronic structure of stoichiometric silicides with Nb, Mo, Ta and W is presented. We have employed x-ray photoemission and bremsstrahlung isochromat spectroscopy as experimental techniques and interpreted the measured data by calculation of

FNR demonstration experiments Part II: Subcadmium neutron flux measurements

International Nuclear Information System (INIS)

Wehe, D.K.; King, J.S.

1983-01-01

The FNR HEU-LEU Demonstration Experiments include a comprehensive set of experiments to identify and quantify significant operational differences between two nuclear fuel enrichments. One aspect of these measurements, the subcadmium flux profiling, is the subject of this paper. The flux profiling effort has been accomplished through foil and wire activations, and by rhodium self-powered neutron detector (SPND) mappings. Within the experimental limitations discussed, the program to measure subcadmium flux profiles, lead to the following conclusions: (1) Replacement of a single fresh HEU element by a fresh LEU element at the center of an equilibrium HEU core produces a local flux depression. The ratio of HEU to LEU local flux is 1.19 ± .036, which is, well within experimental uncertainty, equal to the inverse of the U-235 masses for the two elements. (2) Whole core replacement of a large 38 element equilibrium HEU core by a fresh or nearly unburned LEU core reduces the core flux and raises the flux in both D 2 O and H 2 O reflectors. The reduction in the central core region is 40% to 10.0% for the small fresh 29 element LEU core, and 16% to 18% for a 31 element LEU core 482) with low average burnup 2 O reflector fluxes relative to core fluxes as measured by SPND with a fixed value of sensitivity, are in gross disagreement with the same flux ratios measured by Fe and Rh wire activations. Space dependent refinements of S are calculated to give some improvement in the discrepancy but the major part of the correction remains to be resolved

Babcock and Wilcox plate fabrication experience with uranium silicide spherical fuel

International Nuclear Information System (INIS)

Todd, Lawrence E.; Pace, Brett W.

1996-01-01

This report is written to present the fuel fabrication experience of Babcock and Wilcox using atomized spherical uranium silicide powder. The intent is to demonstrate the ability to fabricate fuel plates using spherical powder and to provide useful information proceeding into the next phase of work using this type of fuel. The limited quantity of resources- spherical powder and time, did not allow for much process optimizing in this work scope. However, the information contained within provides optimism for the future of spherical uranium silicide fuel plate fabrication at Babcock and Wilcox.The success of assembling fuel elements with spherical powder will enable Babcock and Wilcox to reduce overall costs to its customers while still maintaining our reputation for providing high quality research and test reactor products. (author)

Future U.S. supply of Mo-99 production through fission based LEU/LEU technology

International Nuclear Information System (INIS)

James Welsh; Bigles, C.I.; Alejandro Valderrabano

2015-01-01

Coqui RadioPharmaceuticals Corp. (Coqui) has the goal of establishing a medical isotope production facility for securing a continuous domestic supply of the radioisotope molybdenum-99 for U.S. citizens. Coqui will use an LEU/LEU proven and implemented open pool, light-water, 10 MW, reactor design. The facility is being designed with twin reactors for reliability an on-site hot lab chemical processing and a waste conditioning area and a possible generator producing radio-chemistry lab. Coqui identified a 25 acre site adjacent to an existing industrial park in northern central Florida. This land was gifted and transferred to Coqui by the University of Florida Foundation. We are in the process of developing licensing documents related to the facility. The construction permit application for submission to the U.S. Nuclear Regulatory Commission is currently being prepared. Submission is scheduled for mid to late 2015. Community reaction to the proposed development has been positive. We expect to create 220 permanent jobs and we have an anticipated to be operational by 2020. (author)

Future U.S. supply of Mo-99 production through fission based LEU/LEU technology.

Science.gov (United States)

Welsh, James; Bigles, Carmen I; Valderrabano, Alejandro

Coquí RadioPharmaceuticals Corp. (Coquí) has the goal of establishing a medical isotope production facility for securing a continuous domestic supply of the radioisotope molybdenum-99 for U.S. citizens. Coquí will use an LEU/LEU proven and implemented open pool, light-water, 10 MW, reactor design. The facility is being designed with twin reactors for reliability an on-site hot lab chemical processing and a waste conditioning area and a possible generator producing radio-chemistry lab. Coquí identified a 25 acre site adjacent to an existing industrial park in northern central Florida. This land was gifted and transferred to Coquí by the University of Florida Foundation. We are in the process of developing licensing documents related to the facility. The construction permit application for submission to the U.S. Nuclear Regulatory Commission is currently being prepared. Submission is scheduled for mid to late 2015. Community reaction to the proposed development has been positive. We expect to create 220 permanent jobs and we have an anticipated to be operational by 2020.

Reduced Enrichment for Research and Test Reactors. Proceedings of the XIV international meeting

Energy Technology Data Exchange (ETDEWEB)

Suripto, Asmedi; Hastowo, Hudi; Hersubeno, J B [eds.

1995-07-01

Apart from the progress of the Reduced Enrichment Research and Test Reactor (RERTR) Program the national programs of Indonesia, Japan and China were presented. The major events, findings, and activities of 1991 are reviewed with a brief summary of the results which the RERTR Program had achieved by the end of 1990 in collaboration with its many international partners. The RERTR program, has concentrated its efforts on technology transfer and implementation activities consistent with the guidance received from the Department of Energy at the end of 1990. A number of presentations were devoted to development of new fuel uranium silicide fuel elements, fuel irradiation testing and reactor core conversions from highly enriched (HEU) to slightly enriched uranium (LEU). Calculations and measurements of converted reactor core parameters were shown related to safety test and analysis. Fuel cycle issue were discussed as well. One should note that a significant number of papers were devoted to Indonesian GA SIWABESSY reactor core conversion and related topics.

Reduced Enrichment for Research and Test Reactors. Proceedings of the XIV international meeting

International Nuclear Information System (INIS)

Suripto, Asmedi; Hastowo, Hudi; Hersubeno, J.B.

1995-01-01

Apart from the progress of the Reduced Enrichment Research and Test Reactor (RERTR) Program the national programs of Indonesia, Japan and China were presented. The major events, findings, and activities of 1991 are reviewed with a brief summary of the results which the RERTR Program had achieved by the end of 1990 in collaboration with its many international partners. The RERTR program, has concentrated its efforts on technology transfer and implementation activities consistent with the guidance received from the Department of Energy at the end of 1990. A number of presentations were devoted to development of new fuel uranium silicide fuel elements, fuel irradiation testing and reactor core conversions from highly enriched (HEU) to slightly enriched uranium (LEU). Calculations and measurements of converted reactor core parameters were shown related to safety test and analysis. Fuel cycle issue were discussed as well. One should note that a significant number of papers were devoted to Indonesian GA SIWABESSY reactor core conversion and related topics

The University of Missouri Research Reactor HEU to LEU conversion project status

Energy Technology Data Exchange (ETDEWEB)

McKibben, James C; Kutikkad, Kiratadas; Foyto, Leslie P; Peters, Nickie J; Solbrekken, Gary L; Kennedy, John [University of Missouri Research Reactor, Missouri (United States); Stillman, John A; Feldman, Earl E; Tzanos, Constantine P; Stevens, John G [Argonne National Laboratory, Argonne, Illinois (United States)

2012-03-15

The University of Missouri Research Reactor (MURR) is one of five U.S. high performance research and test reactors that are actively collaborating with the U.S. Department of Energy (DOE) to find a suitable low-enriched uranium (LEU) fuel replacement for the currently required highly-enriched uranium (HEU) fuel. A conversion feasibility study based on U-10Mo monolithic LEU fuel was completed in 2009. It was concluded that the proposed LEU fuel assembly design, in conjunction with an increase in power level from 10 to 12 MWth, will (1) maintain safety margins during operation, (2) allow operating fuel cycle lengths to be maintained for efficient and effective use of the facility, and (3) preserve an acceptable level and spectrum of key neutron fluxes to meet the scientific mission of the facility. The MURR and Argonne National Laboratory (ANL) team is continuing to work toward realization of the conversion. The 'Preliminary Safety Analysis Report Methodologies and Scenarios for LEU Conversion of MURR' was completed in June 2011. This report documents design parameter values critical to the Fuel Development (FD), Fuel Fabrication Capability (FFC) and Hydromechanical Fuel Test Facility (HMFTF) projects. The report also provides a preliminary evaluation of safety analysis techniques and data that will be needed to complete the fuel conversion Safety Analysis Report (SAR), especially those related to the U-10Mo monolithic LEU fuel. Specific studies are underway to validate the proposed path to an LEU fuel conversion. Coupled fluid-structure simulations and experiments are being conducted to understand the hydrodynamic plate deformation risk for 0.965 mm (38 mil) thick fuel plates. Methodologies that were recently developed to answer the U.S. Nuclear Regulatory Commission (NRC) Request for Additional Information (RAI) regarding the MURR 2006 relicensing submittal will be used in the LEU conversion effort. Transition LEU fuel elements that will have a minimal impact on

The Pai-associated leuX specific tRNA5(Leu) affects type 1fimbriation in pathogenic Escherichia coli by control of FimB recombinase expression

DEFF Research Database (Denmark)

Ritter, A.; Gally, D.; Olsen, Peter Bjarke

1997-01-01

The uropathogenic Escherichia coli strain 536 (06:K15:H31) carries two large chromosomalpathogenicity islands (Pais). Both Pais are flanked by tRNA genes. Spontaneous deletion of Pai IIresults in truncation of the leuX tRNA5Leu gene. This tRNA is required for the expression of type 1fimbriae (Fim...

Silicon-germanium and platinum silicide nanostructures for silicon based photonics

Science.gov (United States)

Storozhevykh, M. S.; Dubkov, V. P.; Arapkina, L. V.; Chizh, K. V.; Mironov, S. A.; Chapnin, V. A.; Yuryev, V. A.

2017-05-01

This paper reports a study of two types of silicon based nanostructures prospective for applications in photonics. The first ones are Ge/Si(001) structures forming at room temperature and reconstructing after annealing at 600°C. Germanium, being deposited from a molecular beam at room temperature on the Si(001) surface, forms a thin granular film composed of Ge particles with sizes of a few nanometers. A characteristic feature of these films is that they demonstrate signs of the 2 x 1 structure in their RHEED patterns. After short-term annealing at 600°C under the closed system conditions, the granular films reconstruct to heterostructures consisting of a Ge wetting layer and oval clusters of Ge. A mixed type c(4x2) + p(2x2) reconstruction typical to the low-temperature MBE (Tgr Ge. The other type of the studied nanostructures is based on Pt silicides. This class of materials is one of the friendliest to silicon technology. But as silicide film thickness reaches a few nanometers, low resistivity becomes of primary importance. Pt3Si has the lowest sheet resistance among the Pt silicides. However, the development of a process of thin Pt3Si films formation is a challenging task. This paper describes formation of a thin Pt3Si/Pt2Si structures at room temperature on poly-Si films. Special attention is paid upon formation of poly-Si and amorphous Si films on Si3N4 substrates at low temperatures.

Mechanochemical synthesis and spark plasma sintering of the cerium silicides

Energy Technology Data Exchange (ETDEWEB)

Alanko, Gordon A.; Jaques, Brian; Bateman, Allyssa [Department of Materials Science and Engineering, College of Engineering, Boise State University, 1910 University Drive, Boise, ID 83725 (United States); Butt, Darryl P., E-mail: darrylbutt@boisestate.edu [Department of Materials Science and Engineering, College of Engineering, Boise State University, 1910 University Drive, Boise, ID 83725 (United States); Center for Advanced Energy Studies, 995 University Boulevard, Idaho Falls, ID 83401 (United States)

2014-12-15

Highlights: • Ce{sub 5}Si{sub 3}, Ce{sub 3}Si{sub 2}, CeSi, CeSi{sub 2−x} and CeSi{sub 2} were mechanochemically synthesized. • Temperature and pressure were monitored to investigate reaction progress. • All syntheses proceeded through a MSR event followed by rapid solid-state diffusion. • Milling time before MSR correlates well with effective heat of formation. • Some synthesized material was densified by spark plasma sintering. - Abstract: The cerium silicides, Ce{sub 5}Si{sub 3}, Ce{sub 3}Si{sub 2}, CeSi, CeSi{sub 2−y}, and CeSi{sub 2−x}, have been prepared from the elements by mechanochemical processing in a planetary ball mill. Preparation of the cerium silicide Ce{sub 5}Si{sub 4} was unsuccessfully attempted and potential reasons for this are discussed. Temperature and pressure of the milling vial were monitored in situ to gain insight into the mechanochemical reaction kinetics, which include a mechanically-induced self-propagating reaction (MSR). Some prepared powders were consolidated by spark plasma sintering to high density. Starting materials, as-milled powders, and consolidated samples were characterized by X-ray diffraction, scanning electron microscopy, and energy dispersive spectroscopy. The results obtained help elucidate key questions in mechanochemical processing of intermetallics, showing first phase formation similar to thin films, MSR ignition times that are composition- and milling speed-dependent, and sensitivity of stable compound formation on the impact pressure. The results demonstrate mechanochemical synthesis as a viable technique for rare earth silicides.

Towards the improvement of the oxidation resistance of Nb-silicides in situ composites: A solid state diffusion approach

International Nuclear Information System (INIS)

Mathieu, S.; Knittel, S.; François, M.; Portebois, L.; Mathieu, S.; Vilasi, M.

2014-01-01

Highlights: •Local equilibrium is attained during oxidation at phase boundaries (steady state conditions). •A solid state diffusion model explains the oxidation mechanism of Nb-silicides composites. •The Nb ss fraction is not the only parameters governing the oxidation rate of Nb-silicides. •Aluminium increases the thermodynamic activity of Si in the Nb-silicides composites. •The results indicate the need to develop a Nb–Ti–Hf–Al–Cr–Si thermodynamic database. -- Abstract: The present study focuses on the oxidation mechanism of Nb-silicide composites and on the effect of the composition on the oxidation rate at 1100 °C. A theoretical approach is proposed based on experimental results and used to optimise the oxidation resistance. The growth model based on multiphase diffusion was experimentally tested and confirmed by manufacturing seven composites with different compositions. It was also found that the effect of the composition has to be evaluated at 1100 °C within a short time duration (50 h), where the oxide scale and the internal oxidation zone both grow according to parabolic kinetics

Automatic whole core depletion and criticality calculations by MCNPX 2.7.0

International Nuclear Information System (INIS)

Kalcheva, S.; Koonen, E.

2012-01-01

Different approaches to perform automatic whole core criticality and depletion calculations in a research reactor using MCNPX 2.7.0 are presented. An approximate method is to use the existing symmetries of the burned fuel material distribution in the core, i.e., the axial, radial and azimuth symmetries around the core center, in order to significantly reduce the computation time. In this case it is not necessary to give a unique material number to each burn up cell. Cells having similar burn up and power, achieved during similar irradiation history at same initial fuel composition, will experience similar composition evolution and can therefore be given the same material number. To study the impact of the number of unique burn up materials on the computation time and utilized RAM memory, several MCNPX models have been developed. The paper discusses the accuracy of the model on comparison with measurements of BR2 operation cycles in function of the number of unique burn up materials and the impact of the used Q-value (MeV/fission) of the recoverable fission energy. (authors)

The French UMo group contribution to new LEU fuel development

International Nuclear Information System (INIS)

Hamy, J.M.; Lemoine, P.; Huet, F.; Jarousse, C.; Emin, J.L.

2005-01-01

The French UMo Group was based on a close collaboration between CEA and AREVA's companies strongly involved in the MTR field. The aim of this program was to deliver industrially a high performance LEU UMo fuel able to be reprocessed, and suitable for a wide range of Research Reactor, covering the expected needs for MTR next generation. Since 1999, the program has been focused on industrial aspects with the intention to deal with the whole fuel cycle: manufacturing, irradiation behaviour, fuel characterisation, code development and reprocessing validation. It has been based on the fabrication of full-sized U-7%Mo fuel plates with a density up to 8 gU/cm 3 . The dedicated and advanced R and D means provided by the CEA have been used intensively with the contribution of HFR and BR2 facilities in Europe. This paper presents a synthesis of the program and the corresponding significant results obtained. These results have played a major role as regards the UMo dispersion fuel qualification route by issuing, for the first time, evidence of severe performance limitations. Consequently, the global international effort to develop and qualify a high density LEU UMo fuel has been definitively re-routed and forced to overcome these discrepancies by exploring new technical solutions. A French extended program sustained by a CEA and CERCA collaboration has been launched in 2004 in order to develop a suitable UMo fuel solution. UMo dispersion and monolithic fuel are both investigated through three new full-sized plate irradiations planned in OSIRIS. (author)

Progress in chemical treatment of LEU targets by the modified Cintichem process

International Nuclear Information System (INIS)

Wu, D.; Landsberger, S.; Vandegrift, G.F.

1996-01-01

Presented here are recent experimental results on tests of a modified Cintichem process for producing 99 Mo from low enriched uranium (LEU). Studies were focused in three areas: (1) testing the effects on 99 Mo recovery and purity of dissolving LEU foil in nitric acid alone, rather than in the sulfuric/nitric acid mixture currently used, (2) measuring decontamination factors for radionuclide impurities in each purification step, and (3) testing the effects on processing of adding barrier materials to the LEU metal-foil target. The experimental results show that switching from dissolving the target in the sulfuric/nitric mixture to using nitric acid alone should cause no significant difference in 99 Mo product yield or purity. Further, the results show that overall decontamination factors for gamma emitters in the LEU-target processing are high enough to meet the purity requirements for the 99 Mo product. The results also show that the selected barrier materials, Cu, Fe, and Ni, do not interfere with 99 Mo recovery and can be removed during chemical processing of the LEU target

Immobilization of Uranium Silicide in Sintered Iron-Phosphate Glass

International Nuclear Information System (INIS)

Mateos, Patricia; Russo, Diego; Rodriguez, Diego; Heredia, A; Sanfilippo, M.; Sterba, Mario

2003-01-01

This work is a continuation of a previous one performed in vitrification of uranium silicide in borosilicate and iron-silicate glasses, by sintering.We present the results obtained with an iron-phosphate glass developed at our laboratory and we compare this results with those obtained with the above mentioned glasses. The main objective was to develop a method as simple as possible, so as to get a monolithic glass block with the appropriate properties to be disposed in a deep geological repository.The thermal transformation of the uranium silicide was characterized by DTA/TG analysis and X-ray diffraction.We determined the evolution of the crystalline phases and the change in weight.Calcined uranium silicide was mixed with natural U 3 O 8 , the amount of U 3 O 8 was calculated to simulate an isotopic dilution of 4%.This material was mixed with powdered iron-phosphate glass (in wt.%: 64,9 P 2 O 5 ; 22,7 Fe 2 O 3 ; 8,1 Al 2 O 3 ; 4,3 Na 2 O) in different proportions (in wt%): 7%, 10% y 15%.The powders were pressed and sintered at temperatures between 585 y 670 °C. Samples of the sintered pellet were prepared for the lixiviation tests (MCC-1P: monolithic samples; deionised water; 90° C; 7, 14 and 28 days).The samples showed a quite good durability (0,6 g.m -2 .day -1 ), similar to borosilicate glasses.The microstructure of the glass samples showed that the uranium particles are much better integrated to the glass matrix in the iron-phosphate glasses than in the borosilicate or iron-silicate glasses.We can conclude that the sintered product obtained could be a good alternative for the immobilization of nuclear wastes with high content of uranium, as the ones arising from the conditioning of research reactors spent fuels

Parallelization of a three-dimensional whole core transport code DeCART

Energy Technology Data Exchange (ETDEWEB)

Jin Young, Cho; Han Gyu, Joo; Ha Yong, Kim; Moon-Hee, Chang [Korea Atomic Energy Research Institute, Yuseong-gu, Daejon (Korea, Republic of)

2003-07-01

Parallelization of the DeCART (deterministic core analysis based on ray tracing) code is presented that reduces the computational burden of the tremendous computing time and memory required in three-dimensional whole core transport calculations. The parallelization employs the concept of MPI grouping and the MPI/OpenMP mixed scheme as well. Since most of the computing time and memory are used in MOC (method of characteristics) and the multi-group CMFD (coarse mesh finite difference) calculation in DeCART, variables and subroutines related to these two modules are the primary targets for parallelization. Specifically, the ray tracing module was parallelized using a planar domain decomposition scheme and an angular domain decomposition scheme. The parallel performance of the DeCART code is evaluated by solving a rodded variation of the C5G7MOX three dimensional benchmark problem and a simplified three-dimensional SMART PWR core problem. In C5G7MOX problem with 24 CPUs, a speedup of maximum 21 is obtained on an IBM Regatta machine and 22 on a LINUX Cluster in the MOC kernel, which indicates good parallel performance of the DeCART code. In the simplified SMART problem, the memory requirement of about 11 GBytes in the single processor cases reduces to 940 Mbytes with 24 processors, which means that the DeCART code can now solve large core problems with affordable LINUX clusters. (authors)

Review on JMTR safety design for LEU core conversion

International Nuclear Information System (INIS)

Komori, Yoshihiro; Yokokawa, Makoto; Saruta, Toru; Inada, Seiji; Sakurai, Fumio; Yamamoto, Katsumune; Oyamada, Rokuro; Saito, Minoru

1993-12-01

Safety of the JMTR was fully reviewed for the core conversion to low enriched uranium fuel. Fundamental policies for the JMTR safety design were reconsidered based on the examination guide for safety design of test and research reactors, and safety of the JMTR was confirmed. This report describes the safety design of the JMTR from the viewpoint of major functions for reactor safety. (author)

The formation of magnetic silicide Fe3Si clusters during ion implantation

Science.gov (United States)

Balakirev, N.; Zhikharev, V.; Gumarov, G.

2014-05-01

A simple two-dimensional model of the formation of magnetic silicide Fe3Si clusters during high-dose Fe ion implantation into silicon has been proposed and the cluster growth process has been computer simulated. The model takes into account the interaction between the cluster magnetization and magnetic moments of Fe atoms random walking in the implanted layer. If the clusters are formed in the presence of the external magnetic field parallel to the implanted layer, the model predicts the elongation of the growing cluster in the field direction. It has been proposed that the cluster elongation results in the uniaxial magnetic anisotropy in the plane of the implanted layer, which is observed in iron silicide films ion-beam synthesized in the external magnetic field.

The formation of magnetic silicide Fe3Si clusters during ion implantation

International Nuclear Information System (INIS)

Balakirev, N.; Zhikharev, V.; Gumarov, G.

2014-01-01

A simple two-dimensional model of the formation of magnetic silicide Fe 3 Si clusters during high-dose Fe ion implantation into silicon has been proposed and the cluster growth process has been computer simulated. The model takes into account the interaction between the cluster magnetization and magnetic moments of Fe atoms random walking in the implanted layer. If the clusters are formed in the presence of the external magnetic field parallel to the implanted layer, the model predicts the elongation of the growing cluster in the field direction. It has been proposed that the cluster elongation results in the uniaxial magnetic anisotropy in the plane of the implanted layer, which is observed in iron silicide films ion-beam synthesized in the external magnetic field

Analysis of gamma dose for 4,8 gU/cm3 density silicide core at the RSG-GAS reactor using MCNP code

International Nuclear Information System (INIS)

Ardani

2011-01-01

Radiation safety analysis should be done following of substitution of fuel density of 2.96 gU/cc to density of 4,8 gU/cc silicide fuels for the RSG-GAS reactor. MCNP-5 code has been used to perform gamma dose calculation of the RSG-GAS reactor. Gamma radiation source at reactor consists of capture gamma rays, prompt fission gamma rays, and gamma rays of decay of fission and activation products. The strength of the prompt fission gamma rays is obtained by gamma releases of fission process of U-235 and reactor power of 30 MWt., during 46,6 days operation. Radiation dose is calculated at the experimental hall by detection point at the surface of outer of biological shielding and the operation hall by detection point at the top of the pool. The calculation is conducted at reactor on the normal operation and on the worst postulated accident causing the water level at the pool decreases. Calculation result shows that the biggest source strength of gamma rays come from the decay process. The highest calculated dose at the experiment hall is 4,07x10 -3 μSv/h, far from the maximum external dose permitted 25 μSv/h. The highest calculated dose at the operation hall is 19.98 μSv/h. Even though the calculated dose is still acceptable but this is close to the maximum permitted dose for worker. It concluded that loading of 4,8 gU/cc silicide fuel for the RSG-GAS still safe. (author)

The Analysis of the Effect of Coolant Channel Width on Fuel Loading of the RSG-GAS Core

International Nuclear Information System (INIS)

Surbakti; Tukiran

2004-01-01

The RGS-GAS using uranium silicide fuel, plate type and 250 g U of loading is planned to increase the fuel loading to 300 g U even to 400 g U. The silicide fuel has advantages when increase the fuel loading in the same volume. Because of that case, it is necessary to analyze the effect of coolant channel width on fuel loading of the RSG-GAS core. Analyzing the effect the work which done is to generate cell and core calculation using WIMSD/4 and Batan-2DIFF codes. The WIMSD/4 code is used to generate cross section of core material and Batan-2DIFF is used to calculate the effective multiplication factor. The model that used in this calculation there are three kind of fuel loading namely, 250 g U, 300 g U and 400 g U. The coolant channel width is simulated from 1.75 mm to 2.55 mm. From that fuel loadings, it is analyzed which coolant channel width gave the best effective multiplication factor. From result of analysis showed that the best effective multiplication factor is on the coolant channel width of 2.55 mm for third of fuel loadings. (author)

Supplemental Thermal-Hydraulic Transient Analyses of BR2 in Support of Conversion to LEU Fuel

Energy Technology Data Exchange (ETDEWEB)

Licht, J. [Argonne National Lab. (ANL), Argonne, IL (United States); Dionne, B. [Argonne National Lab. (ANL), Argonne, IL (United States); Sikik, E. [Belgian Nuclear Research Center (SCK-CEN), Mol (Belgium); Van den Branden, G. [Belgian Nuclear Research Center (SCK-CEN), Mol (Belgium); Koonen, E. [Belgian Nuclear Research Center (SCK-CEN), Mol (Belgium)

2016-01-01

Belgian Reactor 2 (BR2) is a research and test reactor located in Mol, Belgium and is primarily used for radioisotope production and materials testing. The Materials Management and Minimization (M3) Reactor Conversion Program of the National Nuclear Security Administration (NNSA) is supporting the conversion of the BR2 reactor from Highly Enriched Uranium (HEU) fuel to Low Enriched Uranium (LEU) fuel. The RELAP5/Mod 3.3 code has been used to perform transient thermal-hydraulic safety analyses of the BR2 reactor to support reactor conversion. A RELAP5 model of BR2 has been validated against select transient BR2 reactor experiments performed in 1963 by showing agreement with measured cladding temperatures. Following the validation, the RELAP5 model was then updated to represent the current use of the reactor; taking into account core configuration, neutronic parameters, trip settings, component changes, etc. Simulations of the 1963 experiments were repeated with this updated model to re-evaluate the boiling risks associated with the currently allowed maximum heat flux limit of 470 W/cm² and temporary heat flux limit of 600 W/cm². This document provides analysis of additional transient simulations that are required as part of a modern BR2 safety analysis report (SAR). The additional simulations included in this report are effect of pool temperature, reduced steady-state flow rate, in-pool loss of coolant accidents, and loss of external cooling. The simulations described in this document have been performed for both an HEU- and LEU-fueled core.

Phase analyses of silicide or nitride coated U–Mo and U–Mo–Ti particle dispersion fuel after out-of-pile annealing

Energy Technology Data Exchange (ETDEWEB)

Kim, Woo Jeong [Korea Atomic Energy Research Institute, 989-111 Daedeok-daero, Yuseong, Daejeon 305-353 (Korea, Republic of); Palancher, Hervé [CEA, DEN, DEC, F-13108 Saint Paul Lez Durance Cedex (France); Ryu, Ho Jin, E-mail: hojinryu@kaist.ac.kr [Korea Advanced Institute of Science and Technology, 291 Daehak-ro, Yuseong, Daejeon 305-701 (Korea, Republic of); Park, Jong Man; Nam, Ji Min [Korea Atomic Energy Research Institute, 989-111 Daedeok-daero, Yuseong, Daejeon 305-353 (Korea, Republic of); Bonnin, Anne [CEA, DEN, DEC, F-13108 Saint Paul Lez Durance Cedex (France); ESRF, 6, rue J. Horowitz, F-38000 Grenoble Cedex (France); Honkimäki, Veijo [ESRF, 6, rue J. Horowitz, F-38000 Grenoble Cedex (France); Charollais, François [CEA, DEN, DEC, F-13108 Saint Paul Lez Durance Cedex (France); Lemoine, Patrick [CEA, DEN, DISN, 91191 Gif sur Yvette (France)

2014-03-15

Highlights: • Silicide or nitride layers were coated on atomized U–Mo or U–Mo–Ti powder. • The constituent phases after annealing were identified through high-energy XRD. • U{sub 3}Si{sub 5} and U{sub 4}Mo(Mo{sub x}Si{sub 1−x})Si{sub 2} were identified in the silicide coating layers. • UN was identified for U–Mo particles and UN and U{sub 4}N{sub 7} formed on U–Mo–Ti particles. -- Abstract: The coating of silicide or nitride layers on U–7 wt%Mo or U–7 wt%Mo–1 wt%Ti particles has been proposed for the minimization of the interaction phase growth in U–Mo/Al dispersion fuel during irradiation. Out-of-pile annealing tests show reduced inter-diffusion by forming silicide or nitride protective layers on U–Mo and U–Mo–Ti particles. To characterize the constituent phases of the coated layers on U–Mo and U–Mo–Ti particles and the interaction phases of coated U–Mo and U–Mo–Ti particle dispersed Al matrix fuel, synchrotron X-ray diffraction experiments have been performed. It was identified that silicide coating layers consisted mainly of U{sub 3}Si{sub 5} and U{sub 4}Mo(Mo{sub x}Si{sub 1−x})Si{sub 2}, and nitride coating layers were composed of mainly UN and U{sub 4}N{sub 7}. The interaction phases obtained after annealing of coated U–Mo and U–Mo–Ti particle dispersion samples were identical to those found in U–Mo/Al–Si and U–Mo/Al systems. Nitride-coated particles showed less interaction formation than silicide-coated particles after annealing at 580 °C for 1 h owing to the higher susceptibility to breakage of the silicide coating layers during hot extrusion.

Optical anisotropy of quasi-1D rare-earth silicide nanostructures on Si(001)

Energy Technology Data Exchange (ETDEWEB)

Chandola, S., E-mail: sandhya.chandola@isas.de [Leibniz-Institut für Analytische Wissenschaften – ISAS – e.V., Schwarzschildstraße 8, 12489 Berlin (Germany); Speiser, E.; Esser, N. [Leibniz-Institut für Analytische Wissenschaften – ISAS – e.V., Schwarzschildstraße 8, 12489 Berlin (Germany); Appelfeller, S.; Franz, M.; Dähne, M. [Institut für Festkörperphysik, Technische Universität Berlin, Hardenbergstraße 36, 10623 Berlin (Germany)

2017-03-31

Highlights: • Reflectance anisotropy spectroscopy (RAS) is capable of distinguishing optically between the semiconducting wetting layer and the metallic nanowires of rare earth (Tb and Dy) silicide nanostructures grown on vicinal Si(001). • The spectra of the wetting layer show a distinctive line shape with a large peak appearing at 3.8 eV, which is assigned to the formation of 2 × 3 and 2 × 4-like subunits of the 2 × 7 reconstruction. The spectra of the metallic nanowires show peaks at the E{sub 1} and E{sub 2} transitions of bulk Si which is assigned to strong substrate strain induced by the nanowires. • The optical anisotropy of the Tb nanowires is larger than for the Dy nanowires, which is related to the preferential formation of more strained bundles as well as larger areas of clean Si surfaces in the case of Tb. • RAS is shown to be a powerful addition to surface science techniques for studying the formation of rare-earth silicide nanostructures. Its surface sensitivity and rapidity of response make it an ideal complement to the slower but higher resolution of scanning probes of STM and AFM. - Abstract: Rare earth metals are known to interact strongly with Si(001) surfaces to form different types of silicide nanostructures. Using STM to structurally characterize Dy and Tb silicide nanostructures on vicinal Si(001), it will be shown that reflectance anisotropy spectroscopy (RAS) can be used as an optical fingerprint technique to clearly distinguish between the formation of a semiconducting two-dimensional wetting layer and the metallic one-dimensional nanowires. Moreover, the distinctive spectral features can be related to structural units of the nanostructures. RAS spectra of Tb and Dy nanostructures are found to show similar features.

The global threat reduction initiative and conversion of isotope production to LEU targets

International Nuclear Information System (INIS)

Kuperman, A. J.

2005-01-01

The U.S. Global Threat Reduction Initiative (GTRI) has given a decisive impetus to the RERTR program's longstanding goal of converting worldwide production of medical radioisotopes from reliance on bomb-grade, highly enriched uranium (HEU) to low-enriched uranium (LEU) unsuitable for weapons. Although the four major; isotope producers continue to resist calls for conversion, they face mounting pressure from a variety of fronts including: (1) GTRI; (2) a related, multilateral U.S. initiative to forge agreement on conversion among the states that are home to the major producers; (3) an IAEA effort to provide technical assistance that will facilitate large-scale production of medical isotopes using LEU by producers who seek to do so; (4) planned production in the United States of substantial quantities of medical isotopes using LEU; and (5) pending U.S. legislation that would prohibit the export of HEU for production of isotopes as soon as alternative, LEU-produced isotopes are available. Accordingly, it now appears inevitable that worldwide isotope production will be converted from reliance on HEU to LEU. The only remaining question is which producers will be the first to reliably deliver sizeable quantities of LEU-produced isotopes and thereby capture global market share from the others. (author)

Preproghrelin Leu72Met polymorphism is not associated with type 2 diabetes mellitus.

Science.gov (United States)

Kim, Sun-Young; Jo, Dae-Sun; Hwang, Pyoung Han; Park, Ji Hyun; Park, Sung Kwang; Yi, Ho Keun; Lee, Dae-Yeol

2006-03-01

Ghrelin is a novel gut-brain peptide, which exerts somatotropic, orexigenic, and adipogenic effects. Genetic variants of ghrelin have been associated with both obesity and insulin metabolism. In this study, we determined a role of preproghrelin Leu72Met polymorphism on type 2 diabetes mellitus and its relationship to variables studied. Genotypes were assessed by polymerase chain reaction. Frequencies of the Leu72Met polymorphism were found to be 35.4% in the type 2 diabetic patients and 32.5% in the normal controls. The Leu72Met polymorphism was not associated with hypertension, macroangiopathy, retinopathy, serum cholesterol, triglyceride, blood urea nitrogen, HbA(1c), lipoprotein (a), fasting insulin, or 24-hour urinary protein levels in the type 2 diabetic group. However, the Leu72Met polymorphism was clearly associated with serum creatinine levels in the diabetic group, as the Met72 carriers exhibited lower serum creatinine levels than the Met72 noncarriers. Our data indicate that the preproghrelin Leu72Met polymorphism is not associated with type 2 diabetes mellitus. However, the Leu72Met polymorphism is associated with serum creatinine levels. These data suggest that Met72 carrier status may be a predictable marker for diabetic nephropathy or renal impairment in type 2 diabetes mellitus.

Experimental studies of thermal and chemical interactions between oxide and silicide nuclear fuels with water

Energy Technology Data Exchange (ETDEWEB)

farahani, A.A.; Corradini, M.L. [Univ. of Wisconsi, Madison, WI (United States)

1995-09-01

Given some transient power/cooling mismatch is a nuclear reactor and its inability to establish the necessary core cooling, energetic fuel-coolant interactions (FCI`s commonly called `vapor explosions`) could occur as a result of the core melting and coolant contact. Although a large number of studies have been done on energetic FCI`s, very few experiments have been performed with the actual fuel materials postulated to be produced in severe accidents. Because of the scarcity of well-characterized FCI data for uranium allows in noncommercial reactors (cermet and silicide fuels), we have conducted a series of experiments to provide a data base for the foregoing materials. An existing 1-D shock-tube facility was modified to handle depleted radioactive materials (U{sub 3}O{sub 8}-Al, and U{sub 3}Si{sub 2}-Al). Our objectives have been to determine the effects of the initial fuel composition and temperature and the driving pressure (triggering) on the explosion work output, dynamic pressures, transient temperatures, and the hydrogen production. Experimental results indicate limited energetics, mainly thermal interactions, for these fuel materials as compared to aluminum where more chemical reactions occur between the molten aluminum and water.

Cross-Bridge Kelvin Resistor (CBKR) structures for silicide-semiconductor junctions characterization

NARCIS (Netherlands)

Stavitski, N.; van Dal, M.J.H.; Klootwijk, J.H.; Wolters, Robertus A.M.; Kovalgin, Alexeij Y.; Schmitz, Jurriaan

2006-01-01

Analyzing the contact geometry factors for the conventional CBKR structures, it appeared that the contact geometries conventionally used for the metal-to-silicide contact resistance measurements were not always satisfactory to reveal the specific contact resistance values. To investigate these

Synthesis of molybdenum borides and molybdenum silicides in molten salts and their oxidation behavior in an air-water mixture

NARCIS (Netherlands)

Kuznetsov, S.A.; Kuznetsova, S.V.; Rebrov, E.V.; Mies, M.J.M.; Croon, de M.H.J.M.; Schouten, J.C.

2005-01-01

The formation of various coatings in molybdenum-boron and molybdenum-silicon systems was investigated. Boronizing and siliciding treatments were conducted in molten salts under inert gas atm. in the 850-1050 DegC temp. range for 7 h. The presence of boride (e.g. Mo2B, MoB, Mo2B5) and silicide

Influence of impurities on silicide contact formation

International Nuclear Information System (INIS)

Kazdaev, Kh.R.; Meermanov, G.B.; Kazdaev, R.Kh.

2002-01-01

Research objectives of this work are to investigate the influence of light impurities implantation on peculiarities of the silicides formation in molybdenum monocrystal implanted by silicon, and in molybdenum films sputtered on silicon substrate at subsequent annealing. Implantation of the molybdenum samples was performed with silicon ions (90 keV, 5x10 17 cm -2 ). Phase identification was performed by X ray analysis with photographic method of registration. Analysis of the results has shown the formation of the molybdenum silicide Mo 3 Si at 900 deg. C. To find out the influence of impurities present in the atmosphere (C,N,O) on investigated processes we have applied combined implantation. At first, molybdenum was implanted with ions of the basic component (silicon) and then -- with impurities ions. Acceleration energies (40keV for C, 45 keV for N and 50 keV for O) were chosen to obtain the same distribution profiles for basic and impurities ions. Ion doses were 5x10 17 cm -2 for Si-ions and 5x10 16 cm -2 - for impurities. The most important results are reported here. The first, for all three kinds of impurities the decreased formation temperatures of the phase Mo 3 Si were observed; in the case of C and N it was ∼100 deg. and in the case of nitrogen - ∼200 deg. Further, simultaneously with the Mo 3 Si phase, the appearance of the rich-metal phase Mo 5 Si 3 was registered (not observed in the samples without additional implantation). In case of Mo/Si-structure, the implantation of the impurities (N,O) was performed to create the peak concentration (∼4at/%) located in the middle of the molybdenum film (∼ 150nm) deposited on silicon substrate. Investigation carried out on unimplanted samples showed the formation of the silicide molybdenum MoSi 2 , observed after annealing at temperatures 900/1000 deg. C, higher than values 500-600 deg. C reported in other works. It is discovered that electrical conductivity of Mo 5 Si 3 -films synthesized after impurities

Interpretation of gamma-scanning data from the ORR demonstration elements

International Nuclear Information System (INIS)

Bretscher, M.M.; Snelgrove, J.L.; Hobbs, R.W.

1989-01-01

The HEU and LEU fuel elements used in the ORR whole-core demonstration were gamma-scanned to determine the axial distribution of the 140 La and 137 Cs activities. Analysis of this data is now complete. From the 140 La activity distributions cycle-averaged powers were determined while the 137 Cs data provided a measure of the final 235 U burnup in the fuel elements. A method for calculating correction factors for activity gradients transverse to the fuel element axis is presented and is applied to the first mixed core used in the demonstration during the gradual transition to an all LEU core. Results based on the gamma-scanning of the LEU fuel followers are also presented. Improved burnup calculations against which the experimental results are to be compared are now in progress. 7 refs., 21 figs., 3 tabs

Leu-9 (CD 7) positivity in acute leukemias: a marker of T-cell lineage?

Science.gov (United States)

Ben-Ezra, J; Winberg, C D; Wu, A; Rappaport, H

1987-01-01

Monoclonal antibody Leu-9 (CD 7) has been reported to be a sensitive and specific marker for T-cell lineage in leukemic processes, since it is positive in patients whose leukemic cells fail to express other T-cell antigens. To test whether Leu-9 is indeed specific for T-cell leukemias, we examined in detail 10 cases of acute leukemia in which reactions were positive for Leu-9 and negative for other T-cell-associated markers including T-11, Leu-1, T-3, and E-rosettes. Morphologically and cytochemically, 2 of these 10 leukemias were classified as lymphoblastic, 4 as myeloblastic, 2 as monoblastic, 1 as megakaryoblastic, and 1 as undifferentiated. The case of acute megakaryoblastic leukemia is the first reported case to be Leu-9 positive. None of the 10 were TdT positive. Of six cases (two monoblastic, one lymphoblastic, one myeloblastic, one megakaryoblastic, and one undifferentiated) in which we evaluated for DNA gene rearrangements, only one, a peroxidase-positive leukemia, showed a novel band on study of the T-cell-receptor beta-chain gene. We therefore conclude that Leu-9 is not a specific marker to T-cell lineage and that, in the absence of other supporting data, Leu-9 positivity should not be used as the sole basis of classifying an acute leukemia as being T-cell derived.

Core conversion effects on the safety analysis of research reactors

International Nuclear Information System (INIS)

Anoussis, J.N.; Chrysochoides, N.G.; Papastergiou, C.N.

1982-07-01

The safety related parameters of the 5 MW Democritus research reactor that will be affected by the scheduled core conversion to use LEU instead of HEU are considered. The analysis of the safety related items involved in such a core conversion, mainly the consequences due to MCA, DBA, etc., is of a general nature and can, therefore, be applied to other similar pool type reactors as well. (T.A.)

Detailed analysis of uranium silicide dispersion fuel swelling

International Nuclear Information System (INIS)

Hofmann, G.L.; Ryu, Woo-Seog

1991-01-01

Swelling of U 3 Si and U 3 Si 2 is analyzed. The growth of fission gas bubbles appears to be affected by fission rate, fuel loading, and micro structural change taking place in the fuel compounds during irradiation. Several mechanisms are explored to explain the observations. The present work is aimed at a better understanding of the basic swelling phenomenon in order to accurately model irradiation behavior of uranium silicide dispersion fuel. (orig.)

Operational impacts of low-enrichment uranium fuel conversion on the Ford Nuclear Reactor

International Nuclear Information System (INIS)

Bernal, F.E.; Brannon, C.C.; Burgard, N.E.; Burn, R.R.; Cook, G.M.; Simpson, P.A.

1985-01-01

The University of Michigan Department of Nuclear Engineering and the Michigan Memorial-Phoenix Project have been engaged in a cooperative effort with Argonne National Laboratory to test and analyze low-enrichment fuel in the Ford Nuclear Reactor (FNR). The effort was begun in 1979, as part of the Reduced Enrichment Research and Test Reactor Program, to demonstrate on a whole-core basis the feasibility of enrichment reduction from 93% to <20% in Materials Test Reactor-type fuel designs. The first low-enrichment uranium (LEU) core was loaded into the FNR and criticality was achieved on December 8, 1981. The final LEU core was established October 11, 1984. No significant operational impacts have resulted from conversion of the FNR to LEU fuel. Thermal flux in the core has decreased slightly; thermal leakage flux has increased. Rod worths, temperature coefficient, and void coefficient have changed imperceptibly. Impressions from the operators are that power defect has increased slightly and that fuel lifetime has increased

HEU to LEU fuel conversion. Final report

International Nuclear Information System (INIS)

Mulder, R.U.

1994-10-01

The Nuclear Regulatory Commission issued a ruling, effective March 27, 1986, that all U.S. non-power reactors convert from HEU fuel to LEU fuel. A Reduced Enrichment for Research and Test Reactors Program was conducted by the Department of Energy at Argonne National Laboratory to coordinate the development of the high density LEU fuel and assist in the development of Safety Analysis Reports for the smaller non-power reactors. Several meetings were held at Argonne in 1987 with the non-power reactor community to discuss the conversion and to set up a conversion schedule for university reactors. EG ampersand G at Idaho was assigned the coordination of the fuel element redesigns. The fuel elements were manufactured by the Babcock ampersand Wilcox Company in Lynchburg, Virginia. The University of Virginia was awarded a grant by the DOE Idaho Operations Office in 1988 to perform safety analysis studies for the LEU conversion for its 2 MW UVAR and 100 Watt CAVALIER reactors. The University subsequently decided to shut down the CAVALIER reactor. A preliminary SAR on the UVAR, along with Technical Specification changes, was submitted to the NRC in November, 1990. An updated SAR was approved by the NRC in January, 1991. In September, 1992, representatives from the fuel manufacturer (B ampersand W) and the fuel designer (EG ampersand G, Idaho) came to the UVAR facility to observe trial fittings of new 22 plate LEU mock fuel elements. B ampersand W fabricated two non-fuel bearing elements, a regular 22 plate element and a control rod element. The elements were checked against the drawings and test fitted in the UVAR grid plate. The dimensions were acceptable and the elements fit in the grid plate with no problems. The staff made several suggestions for minor construction changes to the end pieces on the elements, which were incorporated into the final design of the actual fuel elements. Selected papers are indexed separately for inclusion in the Energy Science and Technology

HEU to LEU fuel conversion. Final report

Energy Technology Data Exchange (ETDEWEB)

Mulder, R.U.

1994-10-01

The Nuclear Regulatory Commission issued a ruling, effective March 27, 1986, that all U.S. non-power reactors convert from HEU fuel to LEU fuel. A Reduced Enrichment for Research and Test Reactors Program was conducted by the Department of Energy at Argonne National Laboratory to coordinate the development of the high density LEU fuel and assist in the development of Safety Analysis Reports for the smaller non-power reactors. Several meetings were held at Argonne in 1987 with the non-power reactor community to discuss the conversion and to set up a conversion schedule for university reactors. EG&G at Idaho was assigned the coordination of the fuel element redesigns. The fuel elements were manufactured by the Babcock & Wilcox Company in Lynchburg, Virginia. The University of Virginia was awarded a grant by the DOE Idaho Operations Office in 1988 to perform safety analysis studies for the LEU conversion for its 2 MW UVAR and 100 Watt CAVALIER reactors. The University subsequently decided to shut down the CAVALIER reactor. A preliminary SAR on the UVAR, along with Technical Specification changes, was submitted to the NRC in November, 1990. An updated SAR was approved by the NRC in January, 1991. In September, 1992, representatives from the fuel manufacturer (B&W) and the fuel designer (EG&G, Idaho) came to the UVAR facility to observe trial fittings of new 22 plate LEU mock fuel elements. B&W fabricated two non-fuel bearing elements, a regular 22 plate element and a control rod element. The elements were checked against the drawings and test fitted in the UVAR grid plate. The dimensions were acceptable and the elements fit in the grid plate with no problems. The staff made several suggestions for minor construction changes to the end pieces on the elements, which were incorporated into the final design of the actual fuel elements. Selected papers are indexed separately for inclusion in the Energy Science and Technology Database.

Development of whole core thermal-hydraulic analysis program ACT. 4. Simplified fuel assembly model and parallelization by MPI

International Nuclear Information System (INIS)

Ohshima, Hiroyuki

2001-10-01

A whole core thermal-hydraulic analysis program ACT is being developed for the purpose of evaluating detailed in-core thermal hydraulic phenomena of fast reactors including the effect of the flow between wrapper-tube walls (inter-wrapper flow) under various reactor operation conditions. As appropriate boundary conditions in addition to a detailed modeling of the core are essential for accurate simulations of in-core thermal hydraulics, ACT consists of not only fuel assembly and inter-wrapper flow analysis modules but also a heat transport system analysis module that gives response of the plant dynamics to the core model. This report describes incorporation of a simplified model to the fuel assembly analysis module and program parallelization by a message passing method toward large-scale simulations. ACT has a fuel assembly analysis module which can simulate a whole fuel pin bundle in each fuel assembly of the core and, however, it may take much CPU time for a large-scale core simulation. Therefore, a simplified fuel assembly model that is thermal-hydraulically equivalent to the detailed one has been incorporated in order to save the simulation time and resources. This simplified model is applied to several parts of fuel assemblies in a core where the detailed simulation results are not required. With regard to the program parallelization, the calculation load and the data flow of ACT were analyzed and the optimum parallelization has been done including the improvement of the numerical simulation algorithm of ACT. Message Passing Interface (MPI) is applied to data communication between processes and synchronization in parallel calculations. Parallelized ACT was verified through a comparison simulation with the original one. In addition to the above works, input manuals of the core analysis module and the heat transport system analysis module have been prepared. (author)

The formation of magnetic silicide Fe{sub 3}Si clusters during ion implantation

Energy Technology Data Exchange (ETDEWEB)

Balakirev, N. [Kazan National Research Technological University, K.Marx st. 68, Kazan 420015 (Russian Federation); Zhikharev, V., E-mail: valzhik@mail.ru [Kazan National Research Technological University, K.Marx st. 68, Kazan 420015 (Russian Federation); Gumarov, G. [Zavoiskii Physico-Technical Institute of Russian Academy of Sciences, 10/7 Sibirskii trakt st., Kazan 420029 (Russian Federation)

2014-05-01

A simple two-dimensional model of the formation of magnetic silicide Fe{sub 3}Si clusters during high-dose Fe ion implantation into silicon has been proposed and the cluster growth process has been computer simulated. The model takes into account the interaction between the cluster magnetization and magnetic moments of Fe atoms random walking in the implanted layer. If the clusters are formed in the presence of the external magnetic field parallel to the implanted layer, the model predicts the elongation of the growing cluster in the field direction. It has been proposed that the cluster elongation results in the uniaxial magnetic anisotropy in the plane of the implanted layer, which is observed in iron silicide films ion-beam synthesized in the external magnetic field.

The role of fission products in whole core accidents

Energy Technology Data Exchange (ETDEWEB)

Baker, A R [FRSD, UKAEA, RNPDE, Risley, Warrington (United Kingdom); Teague, H J [SRD, UKAEA, Culcheth, Warrington (United Kingdom)

1977-07-01

The review of the role of fission products in whole-core accidents falls into two parts. Firstly, there is a discussion of the hypothetical accidents usually considered in the UK and how they are dealt with. Secondly, there is a discussion of individual topics where fission products are known to be important or might be so. There is a brief discussion of the UK work on the establishment of an equation of state for unirradiated fuel and how this might be extended to incorporate fission product effects. The main issue is the contribution of fission products to the effective vapour pressure and the experimental programme on the pulsed reactor VIPER investigates this. Fission products may influence the probability of occurrence and the severity of MFCIs. Finally, the fission product effects in the pre-disassembly, disassembly and recriticality stages of an accident are discussed. (author)

Syntheses of deuterated leu-enkephalins and their use as internal standards for the quantification of leu-enkephalin by fast atom bombardment mass spectrometry

Energy Technology Data Exchange (ETDEWEB)

Benfenati, E. (Istituto di Ricerche Farmacologiche Mario Negri, Bergamo (Italy) Istituto di Ricerche Farmacologiche Mario Negri, Milan (Italy)); Icardi, G.; Chen, S. (Istituto di Ricerche Farmacologiche Mario Negri, Bergamo (Italy)); Fanelli, R. (Istituto di Ricerche Farmacologiche Mario Negri, Milan (Italy))

1990-04-01

We have developed a synthetic method for the preparation of di- and pentadeuterated leu-enkephalin (LE), Tyr-Gly-Gly-Phe-Leu, by proton-deuterium exchange using CF[sub 3]COOO[sup 2]H. Four to six deuterium atoms are introduced using a reaction temperature of 120[sup o]C and if 5% of [sup 2]H[sub 2]O is added the di-deuterated LE is obtained. These deuterated compounds are used as internal standards to plot calibration curves of LE using fast atom bombardment mass spectrometry. (author).

Secondary neutral mass spectrometry depth profile analysis of silicides

International Nuclear Information System (INIS)

Beckmann, P.; Kopnarski, M.; Oechsner, H.

1985-01-01

The Direct Bombardment Mode (DBM) of Secondary Neutral Mass Spectrometry (SNMS) has been applied for depth profile analysis of two different multilayer systems containing metal silicides. Due to the extremely high depth resolution obtained with low energy SNMS structural details down to only a few atomic distances are detected. Stoichiometric information on internal oxides and implanted material is supplied by the high quantificability of SNMS. (Author)

Aluminium alloyed iron-silicide/silicon solar cells: A simple approach for low cost environmental-friendly photovoltaic technology.

Science.gov (United States)

Kumar Dalapati, Goutam; Masudy-Panah, Saeid; Kumar, Avishek; Cheh Tan, Cheng; Ru Tan, Hui; Chi, Dongzhi

2015-12-03

This work demonstrates the fabrication of silicide/silicon based solar cell towards the development of low cost and environmental friendly photovoltaic technology. A heterostructure solar cells using metallic alpha phase (α-phase) aluminum alloyed iron silicide (FeSi(Al)) on n-type silicon is fabricated with an efficiency of 0.8%. The fabricated device has an open circuit voltage and fill-factor of 240 mV and 60%, respectively. Performance of the device was improved by about 7 fold to 5.1% through the interface engineering. The α-phase FeSi(Al)/silicon solar cell devices have promising photovoltaic characteristic with an open circuit voltage, short-circuit current and a fill factor (FF) of 425 mV, 18.5 mA/cm(2), and 64%, respectively. The significant improvement of α-phase FeSi(Al)/n-Si solar cells is due to the formation p(+-)n homojunction through the formation of re-grown crystalline silicon layer (~5-10 nm) at the silicide/silicon interface. Thickness of the regrown silicon layer is crucial for the silicide/silicon based photovoltaic devices. Performance of the α-FeSi(Al)/n-Si solar cells significantly depends on the thickness of α-FeSi(Al) layer and process temperature during the device fabrication. This study will open up new opportunities for the Si based photovoltaic technology using a simple, sustainable, and los cost method.

Proceedings of the international meeting on research and test reactor core conversions from HEU to LEU fuels

Energy Technology Data Exchange (ETDEWEB)

Travelli, A [Argonne National Laboratory, Argonne, IL (United States)

1983-09-01

Conversion of research and test reactor cores from the use of high enrichment uranium to the use of low enrichment uranium depends on the cooperation of many research organizations, reactor operators, and government agencies. At a technical level, it involves almost all aspects of the fuel cycle, including fuel development, testing, shipping and reprocessing; experiment performance; economics; and safety and licensing aspects. The reactors involved and the conversion activities are distributed among approximately 25 countries, making this a subject which is best dealt with on an international basis. To foster direct communication in this area, the Reduced Enrichment Research and Test Reactor (RERTR) Program, at the Argonne National Laboratory, sponsored this meeting as the fifth of a series which began in 1978. The previous meetings were held at Argonne (International Meeting of Research Reactor Fuel Designers, Developers, and Fabricators, Argonne National Laboratory, Argonne, U.S.A., November 910, 1978), at Saclay (IAEA Consultants' Meeting on Research Reactor Core Conversions from HEU to LEU, Centre d'etudes Nucleaires de Saclay, Saclay, France, December 12-14, 1979), at Argonne (International Meeting on Development, Fabrication and Application of Reduced Enrichment Fuels for Research and Test Reactors, Argonne National Laboratory, Argonne, U.S.A., November 12-14, 1980) and at Juelich (Seminar on Research Reactor Operation and Use, Juelich Nuclear Research Center, Juelich, F.R.G., September 48, 1981). Proceedings from the two most recent previous meetings were published as ANL/RERTR/TM-3 (CONF-801144) and IAEA-SR-77. The spirit of this meeting differs slightly from that of the previous meetings. The advances which have been made and the growing maturity of the effort have caused a gradual shift of emphasis away from those topics which dominated the floor during the first meetings, such as fuel and methods development, and towards topics which concern more

Proceedings of the international meeting on research and test reactor core conversions from HEU to LEU fuels

International Nuclear Information System (INIS)

Travelli, A.

1983-09-01

Conversion of research and test reactor cores from the use of high enrichment uranium to the use of low enrichment uranium depends on the cooperation of many research organizations, reactor operators, and government agencies. At a technical level, it involves almost all aspects of the fuel cycle, including fuel development, testing, shipping and reprocessing; experiment performance; economics; and safety and licensing aspects. The reactors involved and the conversion activities are distributed among approximately 25 countries, making this a subject which is best dealt with on an international basis. To foster direct communication in this area, the Reduced Enrichment Research and Test Reactor (RERTR) Program, at the Argonne National Laboratory, sponsored this meeting as the fifth of a series which began in 1978. The previous meetings were held at Argonne (International Meeting of Research Reactor Fuel Designers, Developers, and Fabricators, Argonne National Laboratory, Argonne, U.S.A., November 910, 1978), at Saclay (IAEA Consultants' Meeting on Research Reactor Core Conversions from HEU to LEU, Centre d'etudes Nucleaires de Saclay, Saclay, France, December 12-14, 1979), at Argonne (International Meeting on Development, Fabrication and Application of Reduced Enrichment Fuels for Research and Test Reactors, Argonne National Laboratory, Argonne, U.S.A., November 12-14, 1980) and at Juelich (Seminar on Research Reactor Operation and Use, Juelich Nuclear Research Center, Juelich, F.R.G., September 48, 1981). Proceedings from the two most recent previous meetings were published as ANL/RERTR/TM-3 (CONF-801144) and IAEA-SR-77. The spirit of this meeting differs slightly from that of the previous meetings. The advances which have been made and the growing maturity of the effort have caused a gradual shift of emphasis away from those topics which dominated the floor during the first meetings, such as fuel and methods development, and towards topics which concern more

Influence of Al addition on phase transformation and thermal stability of nickel silicides on Si(0 0 1)

International Nuclear Information System (INIS)

Huang, Shih-Hsien; Twan, Sheng-Chen; Cheng, Shao-Liang; Lee, Tu; Hu, Jung-Chih; Chen, Lien-Tai; Lee, Sheng-Wei

2014-01-01

Highlights: ► The presence of Al slows down the Ni 2 Si–NiSi phase transformation but significantly promotes the NiSi 2−x Al x formation. ► The behavior of phase transformation strongly depends on the Al concentration of the initial Ni 1−x Al x alloys. ► The Ni 0.91 Al 0.09 /Si system exhibits remarkably improved thermal stability, even after high temperature annealing for 1000 s. ► The relationship between microstructures, electrical property, and thermal stability of Ni(Al) silicides is discussed. -- Abstract: The influence of Al addition on the phase transformation and thermal stability of Ni silicides on (0 0 1)Si has been systematically investigated. The presence of Al atoms is found to slow down the Ni 2 Si–NiSi phase transformation but significantly promote the NiSi 2−x Al x formation during annealing. The behavior of phase transformation strongly depends on the Al concentration of the initial Ni 1−x Al x alloys. Compared to the Ni 0.95 Pt 0.05 /Si and Ni 0.95 Al 0.05 /Si system, the Ni 0.91 Al 0.09 /Si sample exhibits remarkably enhanced thermal stability, even after high temperature annealing for 1000 s. The relationship between microstructures, electrical property, and thermal stability of Ni silicides is discussed to elucidate the role of Al during the Ni 1−x Al x alloy silicidation. This work demonstrated that thermally stable Ni 1−x Al x alloy silicides would be a promising candidate as source/drain (S/D) contacts in advanced complementary metal–oxide-semiconductor (CMOS) devices

Detailed analysis of uranium silicide dispersion fuel swelling

International Nuclear Information System (INIS)

Hofman, G.L.; Ryu, Woo-Seog.

1989-01-01

Swelling of U 3 Si and U 3 Si 2 is analyzed. The growth of fission gas bubbles appears to be affected by fission rate, fuel loading, and microstructural change taking place in the fuel compounds during irradiation. Several mechanisms are explored to explain the observations. The present work is aimed at a better understanding of the basic swelling phenomenon in order to accurately model irradiation behavior of uranium silicide disperson fuel. 5 refs., 10 figs

Standardization of specifications and inspection procedures for LEU plate-type research reactor fuels

International Nuclear Information System (INIS)

1988-06-01

With the transition to high density uranium LEU fuel, fabrication costs of research reactor fuel elements have a tendency to increase because of two reasons. First, the amount of the powder of the uranium compound required increases by more than a factor of five. Second, fabrication requirements are in many cases nearer the fabrication limits. Therefore, it is important that measures be undertaken to eliminate or reduce unnecessary requirements in the specification or inspection procedures of research reactor fuel elements utilizing LEU. An additional stimulus for standardizing specifications and inspection procedures at this time is provided by the fact that most LEU conversions will occur within a short time span, and that nearly all of them will require preparation of new specifications and inspection procedures. In this sense, the LEU conversions offer an opportunity for improving the rationality and efficiency of the fuel fabrication and inspection processes. This report focuses on the standardization of specifications and inspection processes of high uranium density LEU fuels for research reactors. However, in many cases the results can also be extended directly to other research reactor fuels. 15 refs, 1 fig., 3 tabs

Axial SPN and radial MOC coupled whole core transport calculation

International Nuclear Information System (INIS)

Cho, Jin-Young; Kim, Kang-Seog; Lee, Chung-Chan; Zee, Sung-Quun; Joo, Han-Gyu

2007-01-01

The Simplified P N (SP N ) method is applied to the axial solution of the two-dimensional (2-D) method of characteristics (MOC) solution based whole core transport calculation. A sub-plane scheme and the nodal expansion method (NEM) are employed for the solution of the one-dimensional (1-D) SP N equations involving a radial transverse leakage. The SP N solver replaces the axial diffusion solver of the DeCART direct whole core transport code to provide more accurate, transport theory based axial solutions. In the sub-plane scheme, the radial equivalent homogenization parameters generated by the local MOC for a thick plane are assigned to the multiple finer planes in the subsequent global three-dimensional (3-D) coarse mesh finite difference (CMFD) calculation in which the NEM is employed for the axial solution. The sub-plane scheme induces a much less nodal error while having little impact on the axial leakage representation of the radial MOC calculation. The performance of the sub-plane scheme and SP N nodal transport solver is examined by solving a set of demonstrative problems and the C5G7MOX 3-D extension benchmark problems. It is shown in the demonstrative problems that the nodal error reaching upto 1,400 pcm in a rodded case is reduced to 10 pcm by introducing 10 sub-planes per MOC plane and the transport error is reduced from about 150 pcm to 10 pcm by using SP 3 . Also it is observed, in the C5G7MOX rodded configuration B problem, that the eigenvalues and pin power errors of 180 pcm and 2.2% of the 10 sub-planes diffusion case are reduced to 40 pcm and 1.4%, respectively, for SP 3 with only about a 15% increase in the computing time. It is shown that the SP 5 case gives very similar results to the SP 3 case. (author)

X-ray photoemission spectromicroscopy of titanium silicide formation in patterned microstructures

Energy Technology Data Exchange (ETDEWEB)

Singh, S.; Solak, H.; Cerrina, F. [Univ. of Wisconsin-Madison, Stoughton, WI (United States)] [and others

1997-04-01

Titanium silicide has the lowest resistivity of all the refractory metal silicides and has good thermal stability as well as excellent compatibility with Al metallization. It is used as an intermediate buffer layer between W vias and the Si substrate to provide good electrical contact in ULSI technology, whose submicron patterned features form the basis of the integrated circuits of today and tomorrow, in the self aligned silicide (salicide) formation process. TiSi{sub 2} exists in two phases: a metastable C49 base-centered orthorhombic phase with specific resistivity of 60-90 {mu}{Omega}-cm that is formed at a lower temperature (formation anneal) and the stable 12-15 {mu}{Omega}-cm resistivity face-centered orthorhombic C54 phase into which C49 is transformed with a higher temperature (conversion anneal) step. C54 is clearly the target for low resistivity VLSI interconnects. However, it has been observed that when dimensions shrink below 1/mic (or when the Ti thickness drops below several hundred angstroms), the transformation of C49 into C54 is inhibited and agglomeration often occurs in fine lines at high temperatures. This results in a rise in resistivity due to incomplete transformation to C54 and because of discontinuities in the interconnect line resulting from agglomeration. Spectromicroscopy is an appropriate tool to study the evolution of the TiSi2 formation process because of its high resolution chemical imaging ability which can detect bonding changes even in the absence of changes in the relative amounts of species and because of the capability of studying thick {open_quotes}as is{close_quotes} industrial samples.

X-ray photoemission spectromicroscopy of titanium silicide formation in patterned microstructures

International Nuclear Information System (INIS)

Singh, S.; Solak, H.; Cerrina, F.

1997-01-01

Titanium silicide has the lowest resistivity of all the refractory metal silicides and has good thermal stability as well as excellent compatibility with Al metallization. It is used as an intermediate buffer layer between W vias and the Si substrate to provide good electrical contact in ULSI technology, whose submicron patterned features form the basis of the integrated circuits of today and tomorrow, in the self aligned silicide (salicide) formation process. TiSi 2 exists in two phases: a metastable C49 base-centered orthorhombic phase with specific resistivity of 60-90 μΩ-cm that is formed at a lower temperature (formation anneal) and the stable 12-15 μΩ-cm resistivity face-centered orthorhombic C54 phase into which C49 is transformed with a higher temperature (conversion anneal) step. C54 is clearly the target for low resistivity VLSI interconnects. However, it has been observed that when dimensions shrink below 1/mic (or when the Ti thickness drops below several hundred angstroms), the transformation of C49 into C54 is inhibited and agglomeration often occurs in fine lines at high temperatures. This results in a rise in resistivity due to incomplete transformation to C54 and because of discontinuities in the interconnect line resulting from agglomeration. Spectromicroscopy is an appropriate tool to study the evolution of the TiSi2 formation process because of its high resolution chemical imaging ability which can detect bonding changes even in the absence of changes in the relative amounts of species and because of the capability of studying thick open-quotes as isclose quotes industrial samples

Preliminary design study for a carbide LEU-nuclear thermal rocket

International Nuclear Information System (INIS)

Venneri, P.F.; Kim, Y.

2014-01-01

Nuclear space propulsion is a requirement for the successful exploration of the solar system. It offers the possibility of having both a high specific impulse and a relatively high thrust, allowing rapid transit times with a minimum usage of fuel. This paper proposes a nuclear thermal rocket design based on heritage NERVA rockets that makes use of Low Enriched Uranium (LEU) fuel. The Carbide LEU Nuclear Thermal Rocket (C-LEU-NTR) is designed to fulfill the rocket requirements as set forth in the NASA 2009 Mars Mission Design Reference Architecture 5.0, that is provide 25,000 lbf of thrust, operate at full power condition for at least two hours, and have a specific impulse close to 900 s. The neutronics analysis was done using MCNP5 with the ENDF/B-VII.1 neutron library. The thermal hydraulic calculations and size optimization were completed with a finite difference code being developed at the Center for Space Nuclear Research. (authors)

A neutronic feasibility study for LEU conversion of the SAFARI-1 reactor

International Nuclear Information System (INIS)

Pond, R.B.; Hanan, N.A.; Matos, J.E.; Ball, G.

2000-01-01

A neutronic feasibility study to convert the SAFARI-1 reactor from HEU to LEU fuel was performed at Argonne National Laboratory in cooperation with NECSA. Comparisons were made of the reactor performance with the current 90% enriched HEU fuel type (UAl) and two 19.75% enriched LEU fuel types (U 3 Si 2 and U7Mo). The thermal fluxes with the LEU fuels were 3 - 9% lower than with the current HEU fuel. For the same fuel assembly design, a uranium density of approximately 4.5 g/cm 3 was required with U 3 Si 2 -Al fuel and a uranium density of about 4.6 g/cm 3 was required with U7Mo-Al fuel to match the 24.6-day cycle of the UAl-alloy fuel with 0.92 gU/cm 3 . The selection of a suitable LEU fuel and the decision to convert SAFARI-1 will be an economic matter that depends upon the fuel type, fuel assembly design, experiment performance and fuel cycle costs. (author)

Whole core burnup calculations using `MCNP`

Energy Technology Data Exchange (ETDEWEB)

Haran, O; Shaham, Y [Israel Atomic Energy Commission, Beersheba (Israel). Nuclear Research Center-Negev

1996-12-01

Core parameters such as the reactivity, the power distribution and different reactivity coefficients calculated in simulations play an important role in the nuclear reactor handling. Operational safety margins are decided upon, based on the calculated parameters. Thus, the ability to accurately calculate those parameters is of uppermost importance. Such ability exists for fresh cores, using the Monte-Carlo method. The change in the core parameters that results from the core burnup is nowadays calculated within transport codes that simplifies the transport process by using approximations such as the diffusion approximation. The inaccuracy in the burned core parameters arising from the use of such approximations is hard to quantify, leading to an increased gap between the operational routines and the safety limits. A Monte Carlo transport code that caries out accurate static calculations in three dimensional geometries using continuous-energy neutron cross-section data such as the MCNP can be used to generate accurate reaction rates for burnup purposes. Monte Carlo method is statistical by nature, so that the reaction rates calculated will be accurate only to a certain known extent. The purpose of this work was to create a burnup routine that uses the capabilities of the Monte Carlo based MCNP code. It should be noted that burnup using Monte Carlo has been reported in the literatures, but this work is the result of an independent effort (authors).

Whole core burnup calculations using 'MCNP'

International Nuclear Information System (INIS)

Haran, O.; Shaham, Y.

1996-01-01

Core parameters such as the reactivity, the power distribution and different reactivity coefficients calculated in simulations play an important role in the nuclear reactor handling. Operational safety margins are decided upon, based on the calculated parameters. Thus, the ability to accurately calculate those parameters is of uppermost importance. Such ability exists for fresh cores, using the Monte-Carlo method. The change in the core parameters that results from the core burnup is nowadays calculated within transport codes that simplifies the transport process by using approximations such as the diffusion approximation. The inaccuracy in the burned core parameters arising from the use of such approximations is hard to quantify, leading to an increased gap between the operational routines and the safety limits. A Monte Carlo transport code that caries out accurate static calculations in three dimensional geometries using continuous-energy neutron cross-section data such as the MCNP can be used to generate accurate reaction rates for burnup purposes. Monte Carlo method is statistical by nature, so that the reaction rates calculated will be accurate only to a certain known extent. The purpose of this work was to create a burnup routine that uses the capabilities of the Monte Carlo based MCNP code. It should be noted that burnup using Monte Carlo has been reported in the literatures, but this work is the result of an independent effort (authors)

Determining the minimum conditions for soda-anthraquinone pulping of kenaf bast, core, and whole stalk fibers

Science.gov (United States)

James S. Han; Thomas A. Rymsza

1999-01-01

Chemical pulping of kenaf fiber is comparatively new. In this study, bast, core, and whole stalk kenaf fibers were pulped using a soda-AQ pulping process and various pulping conditions. Handsheets were evaluated for density, Canadian standard freeness, brightness, opacity, smoothness, and tensile, burst, and tear indexes and strength. The results indicate that...

LEU fuel fabrication in Argentina

International Nuclear Information System (INIS)

Giorsetti, D.R.; Gomez, J.O.; Marajofsky, A.; Kohut, C.

1985-01-01

As an Institution, aiming to meet with its own needs, CNEA has been intensively developing reduced enriched fuel to use in its own research and test reactors. Development of the fabrication technology as well as the design, installation and operation of the manufacturing plant, have been carried out with its own funds. Irradiation and post-irradiation of test miniplates have been taking place within the framework of the RERTR program. During the last years, CNEA has developed three LEU fuel types. In the previous RERTR meetings, we presented the technological results obtained with these fuel types. This paper focuses on CNEA LEU fuel element manufacturing status and the trained personnel we can offer in design and manufacture fuel capability. CNEA has its own fuel manufacturing technology; the necessary facilities to start the fuel fabrication; qualified technicians and professionals for: fuel design and behaviour analysis; fuel manufacturing and QA; international recognition of its fuel development and manufacturing capability through its ORR miniplate irradiation; its own natural uranium and the future possibility to enrich up to 20% U 235 ; the probability to offer a competitive fuel manufacturing cost in the international market; the disposition to cooperate with all countries that wish to take part and aim to reach an self-sufficiency in their own fuel supply needs

Rare earth silicide nanowires on silicon surfaces

International Nuclear Information System (INIS)

Wanke, Martina

2008-01-01

The growth, structure and electronic properties of rare earth silicide nanowires are investigated on planar and vicinal Si(001) und Si(111) surfaces with scanning tunneling microscopy (STM), low energy electron diffraction (LEED) and angle-resolved photoelectron spectroscopy (ARPES). On all surfaces investigated within this work hexagonal disilicides are grown epitaxially with a lattice mismatch of -2.55% up to +0.83% along the hexagonal a-axis. Along the hexagonal c-axis the lattice mismatch is essentially larger with 6.5%. On the Si(001)2 x 1 surface two types of nanowires are grown epitaxially. The socalled broad wires show a one-dimensional metallic valence band structure with states crossing the Fermi level. Along the nanowires two strongly dispersing states at the anti J point and a strongly dispersing state at the anti Γ point can be observed. Along the thin nanowires dispersing states could not be observed. Merely in the direction perpendicular to the wires an intensity variation could be observed, which corresponds to the observed spacial structure of the thin nanowires. The electronic properties of the broad erbium silicide nanowires are very similar to the broad dysprosium silicide nanowires. The electronic properties of the DySi 2 -monolayer and the Dy 3 Si 5 -multilayer on the Si(111) surface are investigated in comparison to the known ErSi 2 /Si(111) and Er 3 Si 5 /Si(111) system. The positions and the energetic locations of the observed band in the surface Brillouin zone will be confirmed for dysprosium. The shape of the electron pockets in the vector k parallel space is elliptical at the anti M points, while the hole pocket at the anti Γ point is showing a hexagonal symmetry. On the Si(557) surface the structural and electronic properties depend strongly on the different preparation conditions likewise, in particular on the rare earth coverage. At submonolayer coverage the thin nanowires grow in wide areas of the sample surface, which are oriented

Nuclear safety analyses and core design calculations to convert the Texas A & M University Nuclear Science Center reactor to low enrichment uranium fuel. Final report

Energy Technology Data Exchange (ETDEWEB)

Parish, T.A.

1995-03-02

This project involved performing the nuclear design and safety analyses needed to modify the license issued by the Nuclear Regulatory Commission to allow operation of the Texas A& M University Nuclear Science Center Reactor (NSCR) with a core containing low enrichment uranium (LEU) fuel. The specific type of LEU fuel to be considered was the TRIGA 20-20 fuel produced by General Atomic. Computer codes for the neutronic analyses were provided by Argonne National Laboratory (ANL) and the assistance of William Woodruff of ANL in helping the NSCR staff to learn the proper use of the codes is gratefully acknowledged. The codes applied in the LEU analyses were WIMSd4/m, DIF3D, NCTRIGA and PARET. These codes allowed full three dimensional, temperature and burnup dependent calculations modelling the NSCR core to be performed for the first time. In addition, temperature coefficients of reactivity and pulsing calculations were carried out in-house, whereas in the past this modelling had been performed at General Atomic. In order to benchmark the newly acquired codes, modelling of the current NSCR core with highly enriched uranium fuel was also carried out. Calculated results were compared to both earlier licensing calculations and experimental data and the new methods were found to achieve excellent agreement with both. Therefore, even if an LEU core is never loaded at the NSCR, this project has resulted in a significant improvement in the nuclear safety analysis capabilities established and maintained at the NSCR.

analysis of reactivity accidents in MTR for various protection system parameters and core condition

International Nuclear Information System (INIS)

Mohamed, F.M.

2011-01-01

Egypt Second Research Reactor (ETRR-2) core was modified to irradiate LEU (Low Enriched Uranium) plates in two irradiation boxes for fission 99 Mo production. The old core comprising 29 fuel elements and one Co Irradiation Device (CID) and the new core comprising 27 fuel elements, CID, and two 99 Mo production boxes. The in core irradiation has the advantage of no special cooling or irradiation loop is required. The purpose of the present work is the analysis of reactivity accidents (RIA) for ETRR-2 cores. The analysis was done to evaluate the accidents from different point of view:1- Analysis of the new core for various Reactor Protection System (RPS) parameters 2- Comparison between the two cores. 3- Analysis of the 99 Mo production boxes.PARET computer code was employed to compute various parameters. Initiating events in RIA involve various modes of reactivity insertion, namely, prompt critical condition (p=1$), accidental ejection of partial and complete CID uncontrolled withdrawal of a control rod accident, and sudden cooling of the reactor core. The time histories of reactor power, energy released, and the maximum fuel, clad and coolant temperatures of fuel elements and LEU plates were calculated for each of these accidents. The results show that the maximum clad temperatures remain well below the clad melting of both fuel and uranium plates during these accidents. It is concluded that for the new core, the RIA with scram will not result in fuel or uranium plate failure.

The role of fission product in whole core accidents - research in the USA

Energy Technology Data Exchange (ETDEWEB)

Dietrich, L W [Argonne National Laboratory, Division of Reactor Analysis and Safety, Argonne, IL (United States); Jackson, J F [Los Alamos Scientific Laboratory, Q Division - Energy, Los Alamos, NM (United States)

1977-07-01

Clinch River Breeder Reactor (CRBR) Project, is balanced, consisting of a reliability programme to prevent malfunctions or accidents, backup systems to accommodate malfunctions or accidents, and systems to cope with the consequences of CDAs. In connection with the CRBR, the Nuclear Regulatory Commission (NRC) has established that {sup t}he probability of core melt and disruptive accidents can and must be reduced to a sufficiently low level to justify their exclusion from the design basis accident spectrum (a goal probability of 10{sup -6} per reactor-year for dose exceeding current guidelines has been established). Thus, CDA accommodation is approached on the basis of reasonable conservatism in evaluation and mitigation. The ERDA fast reactor safety research programme is presently directed towards establishment of four 'lines of assurance' (LOA). The four lines of assurance are: prevent core disruptive accidents; limit core damage; control CDA progression; attenuate radiological consequences. The considerations of fission product effects germane to the present paper are primarily of concern in evaluation of the second and third lines. Since fission products have the potential for dispersing fuel from the core region and thereby producing reactor shutdown, knowledge of their effects can contribute to demonstrating that there is a low probability (10{sup -2} ) of a CDA initiator producing whole-core involvement. Similarly, knowledge of fission product effects can contribute to demonstrating that there Is a low probability of a whole-core disruptive accident leading to sufficient energy release to challenge the containment capability.

Oxidation-resistant Ge-doped silicide coating on Cr-Cr2Nb alloys by pack cementation

International Nuclear Information System (INIS)

He Yirong

1997-01-01

The halide-activated pack cementation process was modified to produce a Ge-doped silicide diffusion coating on Cr-Cr 2 Nb alloys in a single processing step. The morphology and composition of the coating depended both on the pack composition and processing schedule and also on the composition and microstructure of the substrate. Higher Ge content in the pack suppressed the formation of CrSi 2 and reduced the growth kinetics of the coating. Ge was not homogeneously distributed in the coatings. Under cyclic and isothermal oxidation conditions, the Ge-doped silicide coating protected the Cr-Nb alloys from significant oxidation and from pesting by the formation of a Ge-doped silica film. (orig.)

Whole core neutronics modeling of a TRIGA reactor using integral transport theory

International Nuclear Information System (INIS)

Schwinkendorf, K.N.; Toffer, H.

1990-01-01

An innovative analysis approach for performing whole core reactor physics calculations for TRIGA reactors has been employed recently at the Westinghouse Hanford Company. A deterministic transport theory model with sufficient geometric complexity to evaluate asymmetric loading patterns was used. Calculations of this complexity have been performed in the past using Monte Carlo simulation, such as the MCNP code. However, the Monte Carlo calculations are more difficult to prepare and require more computer time. On the Hanford Site CRAY XMP-18 computer, the new methods required less than one-third of the central processing unit time per calculation as compared to an MCNP calculation using 100,000 neutron histories

Development of technology of high density LEU dispersion fuel fabrication

International Nuclear Information System (INIS)

Wiencek, T.; Totev, T.

2007-01-01

Advanced Materials Fabrication Facilities at Argonne National Laboratory have been involved in development of LEU dispersion fuel for research and test reactors from the beginning of RERTR program. This paper presents development of technology of high density LEU dispersion fuel fabrication for full size plate type fuel elements. A brief description of Advanced Materials Fabrication Facilities where development of the technology was carried out is given. A flow diagram of the manufacturing process is presented. U-Mo powder was manufactured by the rotating electrode process. The atomization produced a U-Mo alloy powder with a relatively uniform size distribution and a nearly spherical shape. Test plates were fabricated using tungsten and depleted U-7 wt.% Mo alloy, 4043 Al and Al-2 wt% Si matrices with Al 6061 aluminum alloy for the cladding. During the development of the technology of manufacturing of full size high density LEU dispersion fuel plates special attention was paid to meet the required homogeneity, bonding, dimensions, fuel out of zone and other mechanical characteristics of the plates.

X-ray-emission studies of chemical bonding in transition-metal silicides

NARCIS (Netherlands)

Weijs, P.J.W.; Leuken, H. van; Groot, R.A. de; Fuggle, J.C.; Reiter, S.; Wiech, G.; Buschow, K.H.J.

1991-01-01

We present Si L2,3 emission-band spectra of a series of 3d and 4d transition-metal (TM) silicides, together wtih Si K emission-band spectra of four 3d TM disilicides. The data are compared with augmented-spherical-wave density-of-states (DOS) calculations, and good agreement is found. The trends we

High pressure studies on uranium and thorium silicide compounds: Experiment and theory

DEFF Research Database (Denmark)

Yagoubi, S.; Heathman, S.; Svane, A.

2013-01-01

The actinide silicides ThSi, USi and USi2 have been studied under high pressure using both theory and experiment. High pressure synchrotron X-ray diffraction experiments were performed on polycrystalline samples in diamond anvil cells at room temperature and for pressures up to 54, 52 and 26 GPa...

Optimizing a three-element core design for the Advanced Neutron Source Reactor

International Nuclear Information System (INIS)

West, C.D.

1995-01-01

Source of neutrons in the proposed Advanced Neutron Source facility is a multipurpose research reactor providing 5-10 times the flux, for neutron beams, of the best existing facilities. Baseline design for the reactor core, based on the ''no new inventions'' rule, was an assembly of two annular fuel elements similar to those used in the Oak Ridge and Grenoble high flux reactors, containing highly enriched U silicide particles. DOE commissioned a study of the use of medium- or low-enriched U; a three-element core design was studied as a means to provide extra volume to accommodate the additional U compound required when the fissionable 235 U has to be diluted with 238 U to reduce the enrichment. This paper describes the design and optimization of that three-element core

Association of ghrelin Leu72Met polymorphism with type 2 diabetes mellitus in Chinese population.

Science.gov (United States)

Liu, Jing; Liu, Jia; Tian, Li-min; Liu, Ju-xiang; Bing, Ya-jun; Zhang, Ji-ping; Wang, Yun-Fang; Zhang, Lu-yan

2012-08-10

Ghrelin, a novel endogenous ligand for the growth hormone secretagogue receptor, is considered to implicate the development of the type 2 diabetes mellitus (T2DM). The Leu72Met (+408C>A) polymorphism of the preproghrelin, has been linked to obesity, insulin resistance and diabetes. To investigate the distribution of ghrelin gene Leu72Met polymorphism and its association with the type 2 diabetes mellitus in Chinese population. We conducted a case-control study on 877 patients with T2DM and 864 controls, which were genotyped by the polymerase chain reaction (PCR) technique, denaturing high performance liquid chromatography (DHPLC) and DNA sequence analysis. Laboratory analyses were carried out in the hospital laboratory. No significant difference in the Leu72Met genotype distributions and allele frequency was observed between type 2 diabetes mellitus and controls (both P>0.05). The polymorphism was not associated with T2DM. However, among the T2DM group, the patients carrying Leu72Leu genotype had significantly increased levels of FPG and serum creatinine compared with variant genotypes (Leu72Met and Met72Met) (Ppolymorphism of the preproghrelin gene was not associated with T2DM in Chinese population. However, it may have some roles in the etiology of insulin resistance. Copyright © 2012 Elsevier B.V. All rights reserved.

3D Monte-Carlo transport calculations of whole slab reactor cores: validation of deterministic neutronic calculation routes

International Nuclear Information System (INIS)

Palau, J.M.

2005-01-01

This paper presents how Monte-Carlo calculations (French TRIPOLI4 poly-kinetic code with an appropriate pre-processing and post-processing software called OVNI) are used in the case of 3-dimensional heterogeneous benchmarks (slab reactor cores) to reduce model biases and enable a thorough and detailed analysis of the performances of deterministic methods and their associated data libraries with respect to key neutron parameters (reactivity, local power). Outstanding examples of application of these tools are presented regarding the new numerical methods implemented in the French lattice code APOLLO2 (advanced self-shielding models, new IDT characteristics method implemented within the discrete-ordinates flux solver model) and the JEFF3.1 nuclear data library (checked against JEF2.2 previous file). In particular we have pointed out, by performing multigroup/point-wise TRIPOLI4 (assembly and core) calculations, the efficiency (in terms of accuracy and computation time) of the new IDT method developed in APOLLO2. In addition, by performing 3-dimensional TRIPOLI4 calculations of the whole slab core (few millions of elementary volumes), the high quality of the new JEFF3.1 nuclear data files and revised evaluations (U 235 , U 238 , Hf) for reactivity prediction of slab cores critical experiments has been stressed. As a feedback of the whole validation process, improvements in terms of nuclear data (mainly Hf capture cross-sections) and numerical methods (advanced quadrature formulas accounting validation results, validation of new self-shielding models, parallelization) are suggested to improve even more the APOLLO2-CRONOS2 standard calculation route. (author)

3D Monte-Carlo transport calculations of whole slab reactor cores: validation of deterministic neutronic calculation routes

Energy Technology Data Exchange (ETDEWEB)

Palau, J M [CEA Cadarache, Service de Physique des Reacteurs et du Cycle, Lab. de Projets Nucleaires, 13 - Saint-Paul-lez-Durance (France)

2005-07-01

This paper presents how Monte-Carlo calculations (French TRIPOLI4 poly-kinetic code with an appropriate pre-processing and post-processing software called OVNI) are used in the case of 3-dimensional heterogeneous benchmarks (slab reactor cores) to reduce model biases and enable a thorough and detailed analysis of the performances of deterministic methods and their associated data libraries with respect to key neutron parameters (reactivity, local power). Outstanding examples of application of these tools are presented regarding the new numerical methods implemented in the French lattice code APOLLO2 (advanced self-shielding models, new IDT characteristics method implemented within the discrete-ordinates flux solver model) and the JEFF3.1 nuclear data library (checked against JEF2.2 previous file). In particular we have pointed out, by performing multigroup/point-wise TRIPOLI4 (assembly and core) calculations, the efficiency (in terms of accuracy and computation time) of the new IDT method developed in APOLLO2. In addition, by performing 3-dimensional TRIPOLI4 calculations of the whole slab core (few millions of elementary volumes), the high quality of the new JEFF3.1 nuclear data files and revised evaluations (U{sup 235}, U{sup 238}, Hf) for reactivity prediction of slab cores critical experiments has been stressed. As a feedback of the whole validation process, improvements in terms of nuclear data (mainly Hf capture cross-sections) and numerical methods (advanced quadrature formulas accounting validation results, validation of new self-shielding models, parallelization) are suggested to improve even more the APOLLO2-CRONOS2 standard calculation route. (author)

LEU fuel fabrication program for the RECH-1 reactor. Status report

International Nuclear Information System (INIS)

Chavez, J.C.; Barrera, M.; Jimenez, O.; Lisboa, J.; Marin, J.

2000-01-01

In 1995 a 50 LEU U 3 Si 2 fuel elements fabrication program for the RECH-1 research reactor was established at the Comision Chilena de Energia Nuclear, CCHEN. After a fabrication process qualification stage, in 1998, four elements were early delivered to the reactor in order to start an irradiation qualification stage. The irradiation has reached an estimated 10% burn-up and no fabrication problems have been detected up to this burn-up level. During 1999 and up to the first quarter of 2000, 19 fuel elements were produced and 7 fuel elements are expected for the end of 2000. This report presents an updated summary of the main results obtained in this fuel fabrication program. A summary of other activities generated by this program, such as in core follow-up of the four leader fuel elements, ISO 9001 implementation for the fabrication process and a fabrication and qualification optimization planning, is also presented here. (author)

LEU WWR-M2 fuel assemblies burnable test

International Nuclear Information System (INIS)

Kirsanov, G.A.; Konoplev, K.A.; Pikulik, R.G.; Sajkov, Yu. P.; Tchmshkyan, D.V.; Tedoradze, L.V.; Zakharov, A.S.

2000-01-01

The results of in-pile irradiation tests of LEU WWR-M2 fuel assemblies with reduced enrichment of fuel are submitted in the report. The tests are made according to the Russian Program on Reduced Enrichment for Research and Test Reactors (RERTR). United States Department of Energy and the Ministry of Atomic Energy of Russian Federation jointly fund this Program. The irradiation tests of 5 WWR-M2 experimental assemblies are carried out at WWR-M reactor of the Petersburg Nuclear Physics Institute (PNPI). The information on assembly design and technique of irradiation tests is presented. In the irradiation tests the integrity of fuel assemblies is periodically measured. The report presents the data for the integrity maintained during the burnup of 5 fuel assemblies up to 45%. These results demonstrate the high reliability of the experimental fuel assemblies within the guaranteed burnup limits specified by the manufacturer. The tests are still in progress; it is planned to test and analyze the change in integrity for burnup of up to 70% - 75% or more. LEU WWR-M2 fuel assemblies are to be offered for export by their Novosibirsk manufacturer. Currently, HEU WWR-M2 fuel assemblies are used in Hungary, Ukraine and Vietnam. LEU WWR-M2 fuel assemblies were designed as a possible replacement for the HEU WWR-M2 fuel assemblies in those countries, but their use can be extended to other research reactors. (author)

What the difference to use LEU and HEU fuel elements separately or together in a research reactor

International Nuclear Information System (INIS)

Kaya, S.; Uestuen, G.

2005-01-01

Concerning of nuclear material safety, most of the research reactors are advised to shift from HEU (high enriched-%93 U-235) to LEU (low enriched-%20 U-235) fuel elements. When LEU and HEU fuel elements are to be used together in a research reactor, some design and safety problems are encountered. According to use of the reactor, some research reactors such as MTR type may not show any considerable difference for HEU or LEU fuel elements, but the efficiency of radioisotope production generated by thermal neutron interaction may decrease about twenty-thirty percent when LEU fuel elements are used. Here, fine mesh-sized 3D neutronic analysis of TR-2 research reactor is presented to indicate the arising problem when LEU end HEU fuel elements are used together in a research reactor. Partial thermohydraulic analysis of the reactor is also given to show the betterness of the LEU fuel element design. However, there might be some points that should be noticed for safer operation of plate type fuelled research reactors. (author)

Thermal hydraulic model validation for HOR mixed core fuel management

International Nuclear Information System (INIS)

Gibcus, H.P.M.; Vries, J.W. de; Leege, P.F.A. de

1997-01-01

A thermal-hydraulic core management model has been developed for the Hoger Onderwijsreactor (HOR), a 2 MW pool-type university research reactor. The model was adopted for safety analysis purposes in the framework of HEU/LEU core conversion studies. It is applied in the thermal-hydraulic computer code SHORT (Steady-state HOR Thermal-hydraulics) which is presently in use in designing core configurations and for in-core fuel management. An elaborate measurement program was performed for establishing the core hydraulic characteristics for a variety of conditions. The hydraulic data were obtained with a dummy fuel element with special equipment allowing a.o. direct measurement of the true core flow rate. Using these data the thermal-hydraulic model was validated experimentally. The model, experimental tests, and model validation are discussed. (author)

How LeuT shapes our understanding of the mechanisms of sodium-coupled neurotransmitter transporters.

Science.gov (United States)

Penmatsa, Aravind; Gouaux, Eric

2014-03-01

Neurotransmitter transporters are ion-coupled symporters that drive the uptake of neurotransmitters from neural synapses. In the past decade, the structure of a bacterial amino acid transporter, leucine transporter (LeuT), has given valuable insights into the understanding of architecture and mechanism of mammalian neurotransmitter transporters. Different conformations of LeuT, including a substrate-free state, inward-open state, and competitive and non-competitive inhibitor-bound states, have revealed a mechanistic framework for the transport and transport inhibition of neurotransmitters. The current review integrates our understanding of the mechanistic and pharmacological properties of eukaryotic neurotransmitter transporters obtained through structural snapshots of LeuT.

Preparation results for lifetime test of conversion LEU fuel in plutonium production reactors

International Nuclear Information System (INIS)

Vatulin, A.; Stetskiy, Yu.; Kukharkin, N.; Kalougin, A.; Gavrilov, P.; Ivanov, A.

1999-01-01

The program of converting Russian production reactors for the purpose to stop their plutonium fabrication is currently in progress. The program also provides for operation of these reactors under the conversion mode with using of low-enriched fuel (LEU). LEU fuel elements were developed and activities related to their preparation for reactor tests were carried out. (author)

HEU to LEU conversion and blending facility: UNH blending alternative to produce LEU oxide for disposal

International Nuclear Information System (INIS)

1995-09-01

The United States Department of Energy (DOE) is examining options for the disposition of surplus weapons-usable fissile materials and storage of all weapons-usable fissile materials. Disposition is a process of use or disposal of material that results in the material being converted to a form that is substantially and inherently more proliferation-resistant than is the original form. Examining options for increasing the proliferation resistance of highly enriched uranium (HEU) is part of this effort. This report provides data to be used in the environmental impact analysis for the uranyl nitrate hexahydrate blending option to produce oxide for disposal. This the Conversion and Blending Facility (CBF) alternative will have two missions (1) convert HEU materials into HEU uranyl nitrate (UNH) and (2) blend the HEU uranyl nitrate with depleted and natural assay uranyl nitrate to produce an oxide that can be stored until an acceptable disposal approach is available. The primary emphasis of this blending operation will be to destroy the weapons capability of large, surplus stockpiles of HEU. The blended LEU product can only be made weapons capable again by the uranium enrichment process. The blended LEU will be produced as a waste suitable for storage or disposal

HEU to LEU conversion and blending facility: UNH blending alternative to produce LEU oxide for disposal

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-09-01

The United States Department of Energy (DOE) is examining options for the disposition of surplus weapons-usable fissile materials and storage of all weapons-usable fissile materials. Disposition is a process of use or disposal of material that results in the material being converted to a form that is substantially and inherently more proliferation-resistant than is the original form. Examining options for increasing the proliferation resistance of highly enriched uranium (HEU) is part of this effort. This report provides data to be used in the environmental impact analysis for the uranyl nitrate hexahydrate blending option to produce oxide for disposal. This the Conversion and Blending Facility (CBF) alternative will have two missions (1) convert HEU materials into HEU uranyl nitrate (UNH) and (2) blend the HEU uranyl nitrate with depleted and natural assay uranyl nitrate to produce an oxide that can be stored until an acceptable disposal approach is available. The primary emphasis of this blending operation will be to destroy the weapons capability of large, surplus stockpiles of HEU. The blended LEU product can only be made weapons capable again by the uranium enrichment process. The blended LEU will be produced as a waste suitable for storage or disposal.

ANL progress in developing an LEU target and process for Mo-99 production: Cooperation with CNEA

International Nuclear Information System (INIS)

Gelis, A.V.; Vandegrift, G.F.; Aase, S.B.; Bakel, A.J.; Falkenberg, J.R.; Regalbuto, M.C.; Quigley, K.J.

2003-01-01

The primary mission of the Reduced Enrichment in Research and Test Reactors (RERTR) Program is to facilitate the conversion of research and test-reactor fuel and targets from high-enriched uranium (HEU) to low-enriched uranium (LEU). One of the current goals at Argonne National Laboratory (ANL) is to assist the Argentine Comision Nacional de Energia Atomica (CNEA) in developing an LEU foil target and a process for 99 Mo production. Specifically addressed in this paper is ANL R and D related to this conversion: (1) designing a prototype production vessel for digesting irradiated LEU foils in alkaline solutions and (2) developing a new digestion method to address all issues related to HEU to LEU conversion. (author)

Rare earth silicide nanowires on silicon surfaces

Energy Technology Data Exchange (ETDEWEB)

Wanke, Martina

2008-11-10

The growth, structure and electronic properties of rare earth silicide nanowires are investigated on planar and vicinal Si(001) und Si(111) surfaces with scanning tunneling microscopy (STM), low energy electron diffraction (LEED) and angle-resolved photoelectron spectroscopy (ARPES). On all surfaces investigated within this work hexagonal disilicides are grown epitaxially with a lattice mismatch of -2.55% up to +0.83% along the hexagonal a-axis. Along the hexagonal c-axis the lattice mismatch is essentially larger with 6.5%. On the Si(001)2 x 1 surface two types of nanowires are grown epitaxially. The socalled broad wires show a one-dimensional metallic valence band structure with states crossing the Fermi level. Along the nanowires two strongly dispersing states at the anti J point and a strongly dispersing state at the anti {gamma} point can be observed. Along the thin nanowires dispersing states could not be observed. Merely in the direction perpendicular to the wires an intensity variation could be observed, which corresponds to the observed spacial structure of the thin nanowires. The electronic properties of the broad erbium silicide nanowires are very similar to the broad dysprosium silicide nanowires. The electronic properties of the DySi{sub 2}-monolayer and the Dy{sub 3}Si{sub 5}-multilayer on the Si(111) surface are investigated in comparison to the known ErSi{sub 2}/Si(111) and Er{sub 3}Si{sub 5}/Si(111) system. The positions and the energetic locations of the observed band in the surface Brillouin zone will be confirmed for dysprosium. The shape of the electron pockets in the (vector)k {sub parallel} space is elliptical at the anti M points, while the hole pocket at the anti {gamma} point is showing a hexagonal symmetry. On the Si(557) surface the structural and electronic properties depend strongly on the different preparation conditions likewise, in particular on the rare earth coverage. At submonolayer coverage the thin nanowires grow in wide areas

Neutronic analysis of HEU to LEU conversion calculation for AEOI 5 MW pool-type MTR fuel research reactor core

International Nuclear Information System (INIS)

Pazirandeh, A.; Lutz, D.; Bartsch, G.

1987-07-01

The possibility of converting HEU(93%) fuel to LEU(20%) fuel without or with slight alteration to the fuel element geometry is discussed. The fuel density varies between 1.7 to 4.1 g U-235/cm. In cross section generation a unit cell with an extra zone to account for extra Al and water was considered. In burnup calculations a sequential shuffling pattern was assumed with fixed position control fuel elements. A cross section data set in 45 energy groups were generated using RSYST/CGM system using the cross section library JFET. Then for 2D-diffusion calculations homogenized and condensed 5 energy group cross sections were prepared. (orig./HP)

A long-term ultrahigh temperature application of layered silicide coated Nb alloy in air

Science.gov (United States)

Sun, Jia; Fu, Qian-Gang; Li, Tao; Wang, Chen; Huo, Cai-Xia; Zhou, Hong; Yang, Guan-Jun; Sun, Le

2018-05-01

Nb-based alloy possessed limited application service life at ultrahigh temperature (>1400 °C) in air even taking the effective protective coating strategy into consideration for last decades. In this work a long duration of above 128 h at 1500 °C in air was successfully achieved on Nb-based alloy thanked to multi-layered silicide coating. Through optimizing interfaces, the MoSi2/NbSi2 silicide coating with Al2O3-adsorbed-particles layer exhibited three-times higher of oxidation resistance capacity than the one without it. In MoSi2-Al2O3-NbSi2 multilayer coating, the Al2O3-adsorbed-particles layer playing as an element-diffusion barrier role, as well as the formed porous Nb5Si3 layer as a stress transition zone, contributed to the significant improvement.

Electrical and optical properties of sub-10 nm nickel silicide films for silicon solar cells

International Nuclear Information System (INIS)

Brahmi, Hatem; Ravipati, Srikanth; Yarali, Milad; Wang, Weijie; Ryou, Jae-Hyun; Mavrokefalos, Anastassios; Shervin, Shahab

2017-01-01

Highly conductive and transparent films of ultra-thin p-type nickel silicide films have been prepared by RF magnetron sputtering of nickel on silicon substrates followed by rapid thermal annealing in an inert environment in the temperature range 400–600 °C. The films are uniform throughout the wafer with thicknesses in the range of 3–6 nm. The electrical and optical properties are presented for nickel silicide films with varying thickness. The Drude–Lorentz model and Fresnel equations were used to calculate the dielectric properties, sheet resistance, absorption and transmission of the films. These ultrathin nickel silicide films have excellent optoelectronic properties for p-type contacts with optical transparencies up to 80% and sheet resistance as low as ∼0.15 µΩ cm. Furthermore, it was shown that the use of a simple anti-reflection (AR) coating can recover most of the reflected light approaching the values of a standard Si solar cell with the same AR coating. Overall, the combination of ultra-low thickness, high transmittance, low sheet resistance and ability to recover the reflected light by utilizing standard AR coating makes them ideal for utilization in silicon based photovoltaic technologies as a p-type transparent conductor. (paper)

Electrical and optical properties of sub-10 nm nickel silicide films for silicon solar cells

Science.gov (United States)

Brahmi, Hatem; Ravipati, Srikanth; Yarali, Milad; Shervin, Shahab; Wang, Weijie; Ryou, Jae-Hyun; Mavrokefalos, Anastassios

2017-01-01

Highly conductive and transparent films of ultra-thin p-type nickel silicide films have been prepared by RF magnetron sputtering of nickel on silicon substrates followed by rapid thermal annealing in an inert environment in the temperature range 400-600 °C. The films are uniform throughout the wafer with thicknesses in the range of 3-6 nm. The electrical and optical properties are presented for nickel silicide films with varying thickness. The Drude-Lorentz model and Fresnel equations were used to calculate the dielectric properties, sheet resistance, absorption and transmission of the films. These ultrathin nickel silicide films have excellent optoelectronic properties for p-type contacts with optical transparencies up to 80% and sheet resistance as low as ~0.15 µΩ cm. Furthermore, it was shown that the use of a simple anti-reflection (AR) coating can recover most of the reflected light approaching the values of a standard Si solar cell with the same AR coating. Overall, the combination of ultra-low thickness, high transmittance, low sheet resistance and ability to recover the reflected light by utilizing standard AR coating makes them ideal for utilization in silicon based photovoltaic technologies as a p-type transparent conductor.

Production of MO-99 from LEU targets - Acid-side processing

International Nuclear Information System (INIS)

Conner, C.; Sedlet, J.; Wiencek, T.C.

2000-01-01

During 2000, additional targets of the new annular design containing low enriched uranium (LEU) foils were irradiated in the Indonesian RSG-GAS reactor. This new design significantly decreases the target fabrication cost. This irradiation allowed us to compare the irradiation performance of several batches of LEU foil. We also processed one of the irradiated foils to recover 99 Mo using a slightly modified Cintichem process. Finally, we measured some important physical properties of uranyl nitrate solutions (i.e., density and solubility), which will be useful in future efforts to further increase the amount of uranium that can be processed by the Cintichem process. (author)

Purification in the interaction between yttria mould and Nb-silicide-based alloy during directional solidification: A novel effect of yttrium

International Nuclear Information System (INIS)

Ma, Limin; Tang, Xiaoxia; Wang, Bin; Jia, Lina; Yuan, Sainan; Zhang, Hu

2012-01-01

Nb-silicide-based alloys were directionally solidified in yttria moulds. As a result of thermal dissociation of yttria, the alloys were slightly contaminated with oxygen, which caused a competitive oxidation between yttrium and hafnium. The addition of 0.15 at.% yttrium reduced the oxygen increment by 42%, because the buoyant inclusions concentrated around the top surface. The yttrium addition caused a significant purification of the interaction between the yttria mould and the Nb-silicide-based alloys during the directional solidification.

Production of annular blanks for Mo-99 using natural uranium, LEU uranium, nickel and structural Al-3003 plates

International Nuclear Information System (INIS)

Lisboa, J.R.; Barrera, M.E.; Marin, J.

2010-01-01

The Tc-99m radioisotope for medical use is the one most used in nuclear medicine worldwide. In Chile the Tc-99m is applied in more than 90% of nuclear medicine studies. In order to supply the whole country with this radioisotope, in 2005-2007 the CCHEN developed its own production of Tc-99m generators from Mo-99 imported from Canada, which are prepared with the activity needed by the Chilean hospitals and clinics. As of 2007 Mo-99 was no longer imported, and since then the Tc-99m is produced only by neutron activation of the Mo. The present challenge is to produce Mo-99 by irradiating blanks that contain enriched uranium foils, with locally produced LEU. The annular blank consists of 2 concentric tubes of A1-3003 structural aluminum that, in an interior annular space, contain a LEU foil, covered on both sides by a nickel foil. This work presents the development of the production technology for annular blanks using natural uranium and U-325 enriched uranium. The structural components are made with A1-3003 aluminum alloy, the foils are 13 grams of uranium measuring 100 x 50 mm and 120-150 μ thick. The blank was assembled using a methodology to control, adapt and assemble the blank's different internal components. A foil of natural uranium and LEU uranium, and a nickel foil are included, used as a barrier for the escape of fission products. During the blank's expansion, for analysis alcohol as lubricant was used, allowing the expander to move smoothly through the inside of the blank. The blank was sealed by TIG welding with a pulsed AC current and a mixture of Ar-5% He gases. Two methods were used for the water tightness test; for high escape levels the temperature was used as a promoter of the ΔP provided by hot water and liquid nitrogen, for low escape levels high vacuum technology was used where the ΔP is provided by a high pressure helium atmosphere. The technology for the production of annular LEU blanks was achieved by applying innovations to technologies

TRIGA Research Reactor Conversion to LEU and Modernization of Safety Related Systems

Energy Technology Data Exchange (ETDEWEB)

Sanda, R. M. [Institute for Nuclear Research Piteşti (SCN-Piteşti), Piteşti (Romania)

2014-08-15

The USA and IAEA proposed an international programme to reduce the enrichment of uranium in research reactors by converting nuclear fuel containing HEU into fuel containing 20% enriched uranium. The Government of Romania joined the programme and actively supported political, scientific, technical and economic actions that led to the conversion of the active area of the 14 MW TRIGA reactor at the Institute for Nuclear Research in Piteşti in May 2006. This confirmed the continuity of the Romanian Government’s non-proliferation policy and their active support of international cooperation. Conversion of the Piteşti research reactor was made possible by completion of milestones in the Research Agreement for Reactor Conversion, a contract signed with the US Department of Energy and Argonne National Laboratory. This agreement provided scientific and technical support and the possibility of delivery of all HEU TRIGA fuel to the United States. Additionally, about 65% of the fresh LEU fuel needed to start the conversion was delivered in the period 1992–1994. Furthermore, conversion was promoted through IAEA Technical Cooperation project ROM/4/024 project funded primarily by the United States that supported technical and scientific efforts and the delivery of the remaining required LEU nuclear fuel to complete the conversion. Nuclear fuel to complete the conversion was made by the French company CERCA with a tripartite contract among the IAEA, CERCA and Romania. The contract was funded by the US Department of Energy with a voluntary contribution by the Romanian Government. The contract stipulated manufacturing and delivery of LEU fuel by CERCA with compliance measures for quality, delivery schedule and safety requirements set by IAEA standards and Romanian legislation. The project was supported by the ongoing technical cooperation, safeguards, legal and procurement assistance of the IAEA, in particular its Department of Nuclear Safety. For Romanian research, the

ANL progress in developing a target and process for converting CNEA Mo-99 production to LEU

International Nuclear Information System (INIS)

Vandegrift, G.F.; Gelis, A.; Aase, S.; Bakel, A.; Freiberg, E.; Conner, C.

2002-01-01

The primary mission of the Reduced Enrichment in Research and Test Reactors (RERTR) Program is to facilitate the conversion of research and test reactor fuel and targets from high-enriched uranium (HEU) to low-enriched uranium (LEU). One of the current goals at Argonne National Laboratory (ANL) is to convert 99 Mo production at Argentine Commission Nacional de Energia Atomica (CNEA) from HEU to LEU targets. Specifically addressed in this paper is ANL R and D related to this conversion: (1) designing a prototype production vessel for digesting irradiated LEU foils in alkaline solutions, (2) developing means to improve digestion efficiency, and (3) modifying ion-exchange processes used in the CNEA recovery and purification of 99 Mo to deal with the lower volumes generated from LEU-foil digestion. (author)

Thermal expansion and elastic moduli of the silicide based intermetallic alloys Ti5Si3(X) and Nb5Si3

International Nuclear Information System (INIS)

Zhang, L.; Wu, J.

1997-01-01

Silicides are among those potential candidates for high temperature application because of their high melting temperature, low density and good oxidation resistance. Recent interest is focused on molybdenum silicides and titanium silicides. Extensive investigation has been carried out on MoSi 2 , yet comparatively less work was performed on titanium silicides such as Ti 5 Si 3 and Ti 3 and TiSi 2 which are of lower density than MoSi 2 . Fundamental understanding of the titanium silicides' properties for further evaluation their potential for practical application are thus needed. The thermal expansion coefficients and elastic moduli of intermetallic compounds are two properties important for evaluation as a first step. The thermal expansion determines the possible stress that might arise during cooling for these high melting point compounds, which is crucial to the preparation of defect free specimens; and the elastic moduli are usually reflections of the cohesion in crystal. In Frommeyer's work and some works afterwards, the coefficients of thermal expansion were measured on both polycrystalline and single crystal Ti 5 Si 3 . The elastic modulus of polycrystalline Ti 5 Si 3 was measured by Frommeyer and Rosenkranz. However, in the above works, the referred Ti 5 Si 3 was the binary one, no alloying effect has been reported on this matter. Moreover, the above parameters (coefficient of thermal expansion and elastic modulus) of Nb 5 Si 3 remain unreported so far. In this paper, the authors try to extend the knowledge of alloyed Ti 5 Si 3 compounds with Nb and Cr additions. Results on the coefficients of thermal expansion and elastic moduli of Ti 5 Si 3 compounds and Nb 5 Si 3 are presented and the discussion is focused on the alloying effect

A Study on Characterization of Light-Induced Electroless Plated Ni Seed Layer and Silicide Formation for Solar Cell Application

Science.gov (United States)

Takaloo, Ashkan Vakilipour; Joo, Seung Ki; Es, Firat; Turan, Rasit; Lee, Doo Won

2018-03-01

Light-induced electroless plating (LIEP) is an easy and inexpensive method that has been widely used for seed layer deposition of Nickel/Copper (Ni/Cu)-based metallization in the solar cell. In this study, material characterization aspects of the Ni seed layer and Ni silicide formation at different bath conditions and annealing temperatures on the n-side of a silicon diode structure have been examined to achieve the optimum cell contacts. The effects of morphology and chemical composition of Ni film on its electrical conductivity were evaluated and described by a quantum mechanical model. It has been found that correlation exists between the theoretical and experimental conductivity of Ni film. Residual stress and phase transformation of Ni silicide as a function of annealing temperature were evaluated using Raman and XRD techniques. Finally, transmission line measurement (TLM) technique was employed to determine the contact resistance of Ni/Si stack after thermal treatment and to understand its correlation with the chemical-structural properties. Results indicated that low electrical resistive mono-silicide (NiSi) phase as low as 5 mΩ.cm2 was obtained.

Neutronic performance of a 14 MW TRIGA reactor: LEU vs HEU fuel

International Nuclear Information System (INIS)

Bretscher, M.M.; Snelgrove, J.L.; Cornella, R.J.

1983-01-01

A primary objective of the US Reduced Enrichment Research and Test Reactor (RERTR) Program is to develop means for replacing, wherever possible, currently used highly-enriched uranium (HEU) fuel ( 235 U enrichment > 90%) with low-enriched uranium (LEU) fuel ( 235 U enrichment < 20%) without significantly degrading the performance of research and test reactors. The General Atomic Company has developed a low-enriched but high uranium content Er-U-ZrH/sub 1.6/ fuel to enable the conversion of TRIGA reactors (and others) from HEU to LEU. One possible application is to the water-moderated 14 MW TRIGA Steady State Reactor (SSR) at the Romanian Institute for Nuclear Power Reactors. The work reported here was undertaken for the purpose of comparing the neutronic performance of the SSR for HEU fuel with that for LEU fuel. In order to make these relative comparisons as valid as possible, identical methods and models were used for the neutronic calculations

Conceptual designs parameters for MURR LEU U-Mo fuel conversion design demonstration experiment. Revision 1

International Nuclear Information System (INIS)

Stillman, J.; Feldman, E.; Stevens, J.

2013-01-01

The design parameters for the conceptual design of a fuel assembly containing U-10Mo fuel foils with low-enriched uranium (LEU) for the University of Missouri Research Reactor (MURR) are described. The Design Demonstration Experiment (MURR-DDE) will use a prototypic MURR-LEU element manufactured according to the parameters specified here. Also provided are calculated performance parameters for the LEU element in the MURR, and a set of goals for the MURR-DDE related to those parameters. The conversion objectives are to develop a fuel element design that will ensure safe reactor operations, as well as maintaining existing performance. The element was designed by staff members of the Global Threat Reduction Initiative (GTRI) Reactor Conversion Program at the Argonne National Laboratory (ANL) and the MURR Facility. A set of manufacturing assumptions were provided by the Fuel Development (FD) and Fuel Fabrication Capability (FFC) pillars of the GTRI Reduced Enrichment for Research and Test Reactors (RERTR) program to reliably manufacture the fuel plates. The proposed LEU fuel element has an overall design and exterior dimensions that are similar to those of the current highly-enriched uranium (HEU) fuel elements. There are 23 fuel plates in the LEU design. The overall thickness of each plate is 44 mil, except for the exterior plate that is furthest from the center flux trap (plate 23), which is 49 mil thick. The proposed LEU fuel plates have U-10Mo monolithic fuel foils with a 235U enrichment of 19.75% varying from 9 mil to 20 mil thick, and clad with Al-6061 aluminum. A thin layer of zirconium exists between the fuel foils and the aluminum as a diffusion barrier. The thinnest nominal combined zirconium and aluminum clad thickness on each side of the fuel plates is 12 mil. The LEU U-10Mo monolithic fuel is not yet qualified as driver fuel in research reactors, but is under intense development under the auspices of the GTRI FD and FFC programs.

Development of a chromosomally integrated metabolite-inducible Leu3p-alpha-IPM "off-on" gene switch.

Directory of Open Access Journals (Sweden)

Maria Poulou

2010-08-01

Full Text Available Present technology uses mostly chimeric proteins as regulators and hormones or antibiotics as signals to induce spatial and temporal gene expression.Here, we show that a chromosomally integrated yeast 'Leu3p-alpha-IotaRhoMu' system constitutes a ligand-inducible regulatory "off-on" genetic switch with an extensively dynamic action area. We find that Leu3p acts as an active transcriptional repressor in the absence and as an activator in the presence of alpha-isopropylmalate (alpha-IotaRhoMu in primary fibroblasts isolated from double transgenic mouse embryos bearing ubiquitously expressing Leu3p and a Leu3p regulated GFP reporter. In the absence of the branched amino acid biosynthetic pathway in animals, metabolically stable alpha-IPM presents an EC(50 equal to 0.8837 mM and fast "OFF-ON" kinetics (t(50ON = 43 min, t(50OFF = 2.18 h, it enters the cells via passive diffusion, while it is non-toxic to mammalian cells and to fertilized mouse eggs cultured ex vivo.Our results demonstrate that the 'Leu3p-alpha-IotaRhoMu' constitutes a simpler and safer system for inducible gene expression in biomedical applications.

Neutronics analysis of the proposed 25-MW leu TRIGA Multipurpose Research Reactor

International Nuclear Information System (INIS)

Nurdin, M.; Bretscher, M.M.; Snelgrove, J.L.

1982-01-01

More than two years ago the government of Indonesia announced plans to purchase a research reactor for the Puspiptek Research Center in Serpong Indonesia to be used for isotope production, materials testing, neutron physics measurements, and reactor operator training. Reactors using low-enriched uranium (LEU) plate-type and rod-type fuel elements were considered. This paper deals with the neutronic evaluation of the rod-type 25-MW LEU TRIGA Multipurpose Research Reactor (MPRR) proposed by the General Atomic Company of the United States of America

Controlling the formation and stability of ultra-thin nickel silicides - An alloying strategy for preventing agglomeration

Science.gov (United States)

Geenen, F. A.; van Stiphout, K.; Nanakoudis, A.; Bals, S.; Vantomme, A.; Jordan-Sweet, J.; Lavoie, C.; Detavernier, C.

2018-02-01

The electrical contact of the source and drain regions in state-of-the-art CMOS transistors is nowadays facilitated through NiSi, which is often alloyed with Pt in order to avoid morphological agglomeration of the silicide film. However, the solid-state reaction between as-deposited Ni and the Si substrate exhibits a peculiar change for as-deposited Ni films thinner than a critical thickness of tc = 5 nm. Whereas thicker films form polycrystalline NiSi upon annealing above 450 ° C , thinner films form epitaxial NiSi2 films that exhibit a high resistance toward agglomeration. For industrial applications, it is therefore of utmost importance to assess the critical thickness with high certainty and find novel methodologies to either increase or decrease its value, depending on the aimed silicide formation. This paper investigates Ni films between 0 and 15 nm initial thickness by use of "thickness gradients," which provide semi-continuous information on silicide formation and stability as a function of as-deposited layer thickness. The alloying of these Ni layers with 10% Al, Co, Ge, Pd, or Pt renders a significant change in the phase sequence as a function of thickness and dependent on the alloying element. The addition of these ternary impurities therefore changes the critical thickness tc. The results are discussed in the framework of classical nucleation theory.

Study of optical and luminescence properties of silicon — semiconducting silicide — silicon multilayer nanostructures

International Nuclear Information System (INIS)

Galkin, N.G.; Galkin, K.N.; Dotsenko, S.A.; Goroshko, D.L.; Shevlyagin, A.V.; Chusovitin, E.A.; Chernev, I.M.

2017-01-01

By method of in situ differential spectroscopy it was established that at the formation of monolayer Fe, Cr, Ca, Mg silicide and Mg stannide islands on the atomically clean silicon surface an appearance of loss peaks characteristic for these materials in the energy range of 1.1-2.6 eV is observed. An optimization of growth processes permit to grow monolithic double nanoheterostructures (DNHS) with embedded Fe, Cr and Ca nanocrystals, and also polycrystalline DNHS with NC of Mg silicide and Mg stannide and Ca disilicide. By methods of optical spectroscopy and Raman spectroscopy it was shown that embedded NC form intensive peaks in the reflectance spectra at energies up to 2.5 eV and Raman peaks. In DNS with β-FeSi2 NC a photoluminescence and electroluminescence at room temperature were firstly observed.

Verification for excess reactivity on beginning equilibrium core of RSG GAS

International Nuclear Information System (INIS)

Daddy Setyawan; Budi Rohman

2011-01-01

BAPETEN is an institution authorized to control the use of nuclear energy in Indonesia. Control for the use of nuclear energy is carried out through three pillars: regulation, licensing, and inspection. In order to assure the safety of the operating research reactors, the assessment unit of BAPETEN is carrying out independent assessment in order to verify safety related parameters in the SAR including neutronic aspect. The work includes verification to the Power Peaking Factor in the equilibrium silicide core of RSG GAS reactor by computational method using MCNP-ORIGEN. This verification calculation results for is 9.4 %. Meanwhile, the RSG-GAS safety analysis report shows that the excess reactivity on equilibrium core of RSG GAS is 9.7 %. The verification calculation results show a good agreement with the report. (author)

Whole-core damage analysis of EBR-II driver fuel elements following SHRT program

International Nuclear Information System (INIS)

Chang, L.K.; Koenig, J.F.; Porter, D.L.

1987-01-01

In the Shutdown Heat Removal Testing (SHRT) program in EBR-II, fuel element cladding temperatures of some driver subassemblies were predicted to exceed temperatures at which cladding breach may occur. A whole-core thermal analysis of driver subassemblies was performed to determine the cladding temperatures of fuel elemnts, and these temperatures were used for fuel element damage calculation. The accumulated cladding damage of fuel element was found to be very small and fuel element failure resulting from SHRT transients is unlikely. No element breach was noted during the SHRT transients. The reactor was immediately restarted after the most severe SHRT transient had been completed and no driver fuel breach has been noted to date. (orig.)

Role of Ti 3 Al/silicides on tensile properties of Timetal 834 at ...

Indian Academy of Sciences (India)

Extremely fine coherent precipitates of ordered Ti3Al and relatively coarse incoherent precipitates of 2 silicide exist together in the near -titanium alloy, Timetal 834, in the dual phase matrix of primary and transformed . In order to assess the role of these precipitates, three heat treatments viz. WQ, WQ–A and WQ–OA, ...

Prospect of Uranium Silicide fuel element with hypostoichiometric (Si ≤3.7%)

International Nuclear Information System (INIS)

Suripto, A.; Sardjono; Martoyo

1996-01-01

An attempt to obtain high uranium-loading in silicide dispersion fuel element using the fabrication technology applicable nowadays can reach Uranium-loading slightly above 5 gU/cm 3 . It is difficult to achieve a higher uranium-loading than that because of fabricability constraints. To overcome those difficulties, the use of uranium silicide U 3 Si based is considered. The excess of U is obtained by synthesising U 3 Si 2 in Si-hypostoichiometric stage, without applying heat treatment to the ingot as it can generate undesired U 3 Si. The U U will react with the matrix to form U al x compound, that its pressure is tolerable. This experiment is to consider possibilities of employing the U 3 Si 2 as nuclear fuel element which have been performed by synthesising U 3 Si 2 -U with the composition of 3.7 % weigh and 3 % weigh U. The ingot was obtained and converted into powder form which then was fabricated into experimental plate nuclear fuel element. The interaction between free U and Al-matrix during heat-treatment is the rolling phase of the fuel element was observed. The study of the next phase will be conducted later

LAPTM4b recruits the LAT1-4F2hc Leu transporter to lysosomes and promotes mTORC1 activation.

Science.gov (United States)

Milkereit, Ruth; Persaud, Avinash; Vanoaica, Liviu; Guetg, Adriano; Verrey, Francois; Rotin, Daniela

2015-05-22

Mammalian target of rapamycin 1 (mTORC1), a master regulator of cellular growth, is activated downstream of growth factors, energy signalling and intracellular essential amino acids (EAAs) such as Leu. mTORC1 activation occurs at the lysosomal membrane, and involves V-ATPase stimulation by intra-lysosomal EAA (inside-out activation), leading to activation of the Ragulator, RagA/B-GTP and mTORC1 via Rheb-GTP. How Leu enters the lysosomes is unknown. Here we identified the lysosomal protein LAPTM4b as a binding partner for the Leu transporter, LAT1-4F2hc (SLC7A5-SLAC3A2). We show that LAPTM4b recruits LAT1-4F2hc to lysosomes, leading to uptake of Leu into lysosomes, and is required for mTORC1 activation via V-ATPase following EAA or Leu stimulation. These results demonstrate a functional Leu transporter at the lysosome, and help explain the inside-out lysosomal activation of mTORC1 by Leu/EAA.

Summary report on fuel development and miniplate fabrication for the RERTR Program, 1978 to 1990

Energy Technology Data Exchange (ETDEWEB)

Wiencek, T.C. [Argonne National Lab., IL (United States). Energy Technology Div.

1995-08-01

This report summarizes the efforts of the Fabrication Technology Section at Argonne National Laboratory in the program of Reduced Enrichment Research and Test Reactors (RERTR). The main objective of this program was to reduce the amount of high enriched ({approx}93% {sup 235}U) uranium (HEU) used in nonpower reactors. Conversion from low-density (0.8--1.6 g U/cm{sup 3}) HEU fuel elements to highly loaded (up to 7 g U/cm{sup 3}) low-enrichment (<20% {sup 235}U) uranium (LEU) fuel elements allows the same reactor power levels, core designs and sizes to be retained while greatly reducing the possibility of illicit diversion of HEU nuclear fuel. This document is intended as an overview of the period 1978--1990, during which the Section supported this project by fabricating mainly powder metallurgy uranium-silicide dispersion fuel plates. Most of the subjects covered in detail are fabrication-related studies of uranium silicide fuels and fuel plate properties. Some data are included for out-of-pile experiments such as corrosion and compatibility tests. Also briefly covered are most other aspects of the RERTR program such as irradiation tests, full-core demonstrations, and technology transfer. References included are for further information on most aspects of the entire program. A significant portion of the report is devoted to data that were never published in their entirety. The appendices contain a list of previous RERTR reports, ANL fabrication procedures, calculations for phases present in two-phase fuels, chemical analysis of fuels, miniplate characteristics, and a summary of bonding runs made by hot isostatic pressing.

Summary report on fuel development and miniplate fabrication for the RERTR Program, 1978 to 1990

International Nuclear Information System (INIS)

Wiencek, T.C.

1995-08-01

This report summarizes the efforts of the Fabrication Technology Section at Argonne National Laboratory in the program of Reduced Enrichment Research and Test Reactors (RERTR). The main objective of this program was to reduce the amount of high enriched (∼93% 235 U) uranium (HEU) used in nonpower reactors. Conversion from low-density (0.8--1.6 g U/cm 3 ) HEU fuel elements to highly loaded (up to 7 g U/cm 3 ) low-enrichment ( 235 U) uranium (LEU) fuel elements allows the same reactor power levels, core designs and sizes to be retained while greatly reducing the possibility of illicit diversion of HEU nuclear fuel. This document is intended as an overview of the period 1978--1990, during which the Section supported this project by fabricating mainly powder metallurgy uranium-silicide dispersion fuel plates. Most of the subjects covered in detail are fabrication-related studies of uranium silicide fuels and fuel plate properties. Some data are included for out-of-pile experiments such as corrosion and compatibility tests. Also briefly covered are most other aspects of the RERTR program such as irradiation tests, full-core demonstrations, and technology transfer. References included are for further information on most aspects of the entire program. A significant portion of the report is devoted to data that were never published in their entirety. The appendices contain a list of previous RERTR reports, ANL fabrication procedures, calculations for phases present in two-phase fuels, chemical analysis of fuels, miniplate characteristics, and a summary of bonding runs made by hot isostatic pressing

Preliminary investigations for technology assessment of 99Mo production from LEU [low enriched uranium] targets

International Nuclear Information System (INIS)

Vandegrift, G.F.; Chaiko, D.J.; Heinrich, R.R.; Kucera, E.T.; Jensen, K.J.; Poa, D.S.; Varma, R.; Vissers, D.R.

1986-11-01

This paper presents the results of preliminary studies on the effects of substituting low enriched uranium (LEU) for highly enriched uranium (HEU) in targets for the production of fission product 99 Mo. Issues that were addressed are: (1) purity and yield of the 99 Mo//sup 99m/Tc product, (2) fabrication of LEU targets and related concerns, and (3) radioactive waste. Laboratory experimentation was part of the efforts for issues (1) and (2); thus far, radioactive waste disposal has only been addressed in a paper study. Although the reported results are still preliminary, there is reason to be optimistic about the feasibility of utilizing LEU targets for 99 Mo production. 37 refs., 1 fig., 5 tabs

Performance and economic penalties of some LEU [low enriched uranium] conversion options for the Australian Reactor HIFAR

International Nuclear Information System (INIS)

McCulloch, D.B.; Robinson, G.S.

1987-01-01

Performance calculations for the conversion of HIFAR to low enriched uranium (LEU) fuel have been extended to a wide range of 235 U loadings per fuel element. Using a simple approximate algorithm for the likely costs of LEU compared with highly enriched uranium (HEU) fuel elements, the increases in annual fuelling costs for LEU compared with HEU fuel are examined for a range of conversion options involving different performance penalties. No significant operational/safety problems were found for any of the options canvassed. (Author)

Assessment of the effectiveness of the LEU Reform Rule and its implementation

International Nuclear Information System (INIS)

Moran, B.W.; Nations, J.O.; Hammond, G.A.

1993-11-01

The US Nuclear Regulatory Commission (NRC) amended its material control and accounting (MC ampersand A) requirements in 1985 for licensees possessing and using special nuclear material (SNM) of low strategic significance in quantities larger than one effective kilogram (kg). The goal of the Low-Enriched Uranium (LEU) Reform Rule (i.e., 10CFR 74.31) was to establish MC ampersand A requirements for the LEU licensees at a level consistent with the safeguards risk associated with the relatively low strategic importance of such material. The amended requirements were written in a performance-oriented manner, rather than a prescriptive one, in an effort to allow the licensees the opportunity to choose the most cost-effective means of satisfying the requirements. The LEU Reform Rule was implemented in January 1988 and the fuel cycle facilities have had sufficient experience in implementing the rule to allow a meaningful review of its effectiveness. This document provides technical analysis and recommendations to assist the NRC in making a determination if the rule is achieving its intended purpose, and if not, to make the necessary changes to accomplish this

Moissanite (SiC) with metal-silicide and silicon inclusions from tuff of Israel: Raman spectroscopy and electron microscope studies

Science.gov (United States)

Dobrzhinetskaya, Larissa; Mukhin, Pavel; Wang, Qin; Wirth, Richard; O'Bannon, Earl; Zhao, Wenxia; Eppelbaum, Lev; Sokhonchuk, Tatiana

2018-06-01

Here, we present studies of natural SiC that occurs in situ in tuff related to the Miocene alkaline basalt formation deposited in northern part of Israel. Raman spectroscopy, SEM and FIB-assisted TEM studies revealed that SiC is primarily hexagonal polytypes 4H-SiC and 6H-SiC, and that the 4H-SiC polytype is the predominant phase. Both SiC polytypes contain crystalline inclusions of silicon (Sio) and inclusions of metal-silicide with varying compositions (e.g. Si58V25Ti12Cr3Fe2, Si41Fe24Ti20Ni7V5Zr3, and Si43Fe40Ni17). The silicides crystal structure parameters match Si2TiV5 (Pm-3m space group, cubic), FeSi2Ti (Pbam space group, orthorhombic), and FeSi2 (Cmca space group, orthorhombic) respectively. We hypothesize that SiC was formed in a local ultra-reduced environment at respectively shallow depths (60-100 km), through a reaction of SiO2 with highly reducing fluids (H2O-CH4-H2-C2H6) arisen from the mantle "hot spot" and passing through alkaline basalt magma reservoir. SiO2 interacting with the fluids may originate from the walls of the crustal rocks surrounding this magmatic reservoir. This process led to the formation of SiC and accompanied by the reducing of metal-oxides to native metals, alloys, and silicides. The latter were trapped by SiC during its growth. Hence, interplate "hot spot" alkali basalt volcanism can now be included as a geological environment where SiC, silicon, and silicides can be found.

Postirradiation analysis of experimental uranium-silicide dispersion fuel plates

International Nuclear Information System (INIS)

Hofman, G.L.; Neimark, L.A.

1985-01-01

Low-enriched uranium silicide dispersion fuel plates were irradiated to maximum burnups of 96% of 235 U. Fuel plates containing 33 v/o U 3 Si and U 3 Si 2 behaved very well up to this burnup. Plates containing 33 v/o U 3 Si-Al pillowed between 90 and 96% burnup of the fissile atoms. More highly loaded U 3 Si-Al plates, up to 50 v/o were found to pillow at lower burnups. Plates containing 40 v/o U 3 Si showed an increase swelling rate around 85% burnup. 5 refs., 10 figs

Reference equilibrium core with central flux irradiation facility for Pakistan research reactor-1

International Nuclear Information System (INIS)

Israr, M.; Shami, Qamar-ud-din; Pervez, S.

1997-11-01

In order to assess various core parameters a reference equilibrium core with Low Enriched Uranium (LEU) fuel for Pakistan Research Reactor (PARR-1) was assembled. Due to increased volume of reference core, the average neutron flux reduced as compared to the first higher power operation. To get a higher neutron flux an irradiation facility was created in centre of the reference equilibrium core where the advantage of the neutron flux peaking was taken. Various low power experiments were performed in order to evaluate control rods worth and neutron flux mapping inside the core. The neutron flux inside the central irradiation facility almost doubled. With this arrangement reactor operation time was cut down from 72 hours to 48 hours for the production of the required specific radioactivity. (author)

Structures of LeuT in bicelles define conformation and substrate binding in a membrane-like context

Energy Technology Data Exchange (ETDEWEB)

Wang, Hui; Elferich, Johannes; Gouaux, Eric (Oregon HSU)

2012-02-13

Neurotransmitter sodium symporters (NSSs) catalyze the uptake of neurotransmitters into cells, terminating neurotransmission at chemical synapses. Consistent with the role of NSSs in the central nervous system, they are implicated in multiple diseases and disorders. LeuT, from Aquifex aeolicus, is a prokaryotic ortholog of the NSS family and has contributed to our understanding of the structure, mechanism and pharmacology of NSSs. At present, however, the functional state of LeuT in crystals grown in the presence of n-octyl-{beta}-D-glucopyranoside ({beta}-OG) and the number of substrate binding sites are controversial issues. Here we present crystal structures of LeuT grown in DMPC-CHAPSO bicelles and demonstrate that the conformations of LeuT-substrate complexes in lipid bicelles and in {beta}-OG detergent micelles are nearly identical. Furthermore, using crystals grown in bicelles and the substrate leucine or the substrate analog selenomethionine, we find only a single substrate molecule in the primary binding site.

Thermal-hydraulic analysis for core conversion to the use of low-enriched uranium fuels in the KUR

International Nuclear Information System (INIS)

Mishima, Kaichiro; Kanda, Keiji; Shibata, Toshikazu

1985-01-01

A feasibility study has been performed on the core conversion to the use of low-enriched uranium (LEU) fuels in the KUR. Five fuel element geometries are studied. For each fuel element, the relation between the pressure drop and the flow rate, critical heat flux, and heat fluxes for the onset of flow instability and the onset of nucleate boiling are calculated using the computer code PLTEMP3.MOD1 which has been developed for this analysis. The effect of fuel material (UAl x -Al, U 3 O 8 -Al and U 3 Si 2 -Al) on the peak fuel temperatures is also studied. A particular interest in the mixed core which may be constructed on the way to the use of LEU fuels, the change in the bypass flow rate due to the change in the gap between different fuel elements is investigated. (author)

Impact of Nickel silicide Rear Metallization on Series Resistance of Crystalline Silicon Solar Cells

KAUST Repository

Bahabry, Rabab R; Hanna, Amir N; Kutbee, Arwa T; Gumus, Abdurrahman; Hussain, Muhammad Mustafa

2018-01-01

the electrical characteristics of nickel mono-silicide (NiSi)/Cu-Al ohmic contact on the rear side of c-Si solar cells. We observe a significant enhancement in the fill factor of around 6.5% for NiSi/Cu-Al rear contacts leading to increasing the efficiency by 1.2

ENS RRFM '99. Transactions. Oral presentations and posters

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-07-01

The presentations covered the following topics: neutron sources; fissile material supply, fuel fabrication and licensing procedures; research reactors operation and fuel safety issues; back-end options and spent fuel transportation. One of the most significant topics was the conversion from highly enriched uranium (HEU) fuel to low enriched uranium (LEU). The qualification of U{sub 3} Si{sub 2} is well advanced, and the validation of the newly designed U-Mo fuel assemblies, that should enable new conversions, is in progress. Concerning reprocessing the LEU appears to be more difficult to reprocess than HEU (silicide fuel). That is why research and development is conducted to produce LEU fuel with performance characteristics approximating HEU fuel. The issue of transportation of radioactive materials, above all spent fuel elements, from environmental and public acceptance point of view was of significant interest.

ENS RRFM '99. Transactions. Oral presentations and posters

International Nuclear Information System (INIS)

1999-01-01

The presentations covered the following topics: neutron sources; fissile material supply, fuel fabrication and licensing procedures; research reactors operation and fuel safety issues; back-end options and spent fuel transportation. One of the most significant topics was the conversion from highly enriched uranium (HEU) fuel to low enriched uranium (LEU). The qualification of U 3 Si 2 is well advanced, and the validation of the newly designed U-Mo fuel assemblies, that should enable new conversions, is in progress. Concerning reprocessing the LEU appears to be more difficult to reprocess than HEU (silicide fuel). That is why research and development is conducted to produce LEU fuel with performance characteristics approximating HEU fuel. The issue of transportation of radioactive materials, above all spent fuel elements, from environmental and public acceptance point of view was of significant interest

Evaluation of a Core Team Centred Professional Development Programme for Building a Whole-School Cooperative Problem Solving Approach to Conflict

Science.gov (United States)

White, Andrew Jonathan; Wertheim, Eleanor H.; Freeman, Elizabeth; Trinder, Margot

2013-01-01

This study evaluated a professional learning approach using a core team (CT) model to assist primary (elementary) schools to develop whole-school collaborative conflict resolution processes. Thirteen schools were matched and randomly assigned to the enhancing relationships in school communities programme ("n"?=?10) or a non-programme…

A neutronic feasibility study for LEU conversion of the IR-8 research reactor

International Nuclear Information System (INIS)

Deen, J.R.; Hanan, N.A.; Matos, J.E.; Egorenkov, P.M.; Nasonov, V.A.

1998-01-01

Equilibrium fuel cycle comparisons for the IR-8 research reactor were made for HEU (90%), HEU (36%), and LEU (19.75%) fuel assembly (FA) designs using three dimensional multi-group diffusion theory models benchmarked to detailed Monte Carlo models of the reactor. Comparisons were made of changes in reactivity, cycle length, average 235 U discharge burnup, thermal neutron flux, and control rod worths for the 90% and 36% enriched IRT-3M fuel assembly and the 19.75% enriched IRT-4M fuel assembly with the same fuel management strategy. The results of these comparisons showed that a uranium density of 3.5 g/cm 3 in the fuel meat would be required in the LEU IRT-4M fuel assembly to match the cycle length of the HEU (90%) IRT-3M FA and an LEU density of 3.7 g/cm 3 is needed to match the cycle length of the HEU (36%) IRT-3M FA. (author)

Depletion methodology in the 3-D whole core transport code DeCART

Energy Technology Data Exchange (ETDEWEB)

Kim, Kang Seog; Cho, Jin Young; Zee, Sung Quun

2005-02-01

Three dimensional whole-core transport code DeCART has been developed to include a characteristics of the numerical reactor to replace partly the experiment. This code adopts the deterministic method in simulating the neutron behavior with the least assumption and approximation. This neutronic code is also coupled with the thermal hydraulic code CFD and the thermo mechanical code to simulate the combined effects. Depletion module has been implemented in DeCART code to predict the depleted composition in the fuel. The exponential matrix method of ORIGEN-2 has been used for the depletion calculation. The library of including decay constants, yield matrix and others has been used and greatly simplified for the calculation efficiency. This report summarizes the theoretical backgrounds and includes the verification of the depletion module in DeCART by performing the benchmark calculations.

Status of reduced enrichment programs for research reactors in Japan

International Nuclear Information System (INIS)

Kanda, Keiji; Nishihara, Hedeaki; Shirai, Eiji; Oyamada, Rokuro; Sanokawa, Konomo

1997-01-01

The reduced enrichment programs for the JRR-2, JRR-3, JRR-4 and JMTR of Japan Atomic Energy Research Institute (JAERI), and the KUR of Kyoto University Research Reactor Institute (KURRI) have been partially completed and are mostly still in progress under the Joint Study Programs with Argonne National Laboratory (ANL). The JMTR and JRR-2 have been already converted to use MEU aluminide fuels in 1986 and 1987, respectively. The operation of the upgraded JRR-3(JRR-3M) has started in March 1990 with the LEU aluminide fuels. Since May 1992, the two elements have been inserted in the KUR. The safety review application for the full core conversion to use LEU silicide in the JMTR was approved in February 1992 and the conversion has been done in January 1994. The Japanese Government approved a cancellation of the KUHFR Project in February 1991, and in April 1994 the U.S. Government gave an approval to utilize HEU in the KUR instead of the KUHFR. Therefore, the KUR will be operated with HEU fuel until 2001. Since March 1994, Kyoto University is continuing negotiation with UKAEA Dounreay on spent fuel reprocessing and blending down of recovered uranium, in addition to that with USDOE

Status of reduced enrichment programs for research reactors in Japan

Energy Technology Data Exchange (ETDEWEB)

Kanda, Keiji; Nishihara, Hedeaki [Kyoto Univ., Osaka (Japan); Shirai, Eiji; Oyamada, Rokuro; Sanokawa, Konomo [Japan Atomic Energy Research Institute, Tokyo (Japan)

1997-08-01

The reduced enrichment programs for the JRR-2, JRR-3, JRR-4 and JMTR of Japan Atomic Energy Research Institute (JAERI), and the KUR of Kyoto University Research Reactor Institute (KURRI) have been partially completed and are mostly still in progress under the Joint Study Programs with Argonne National Laboratory (ANL). The JMTR and JRR-2 have been already converted to use MEU aluminide fuels in 1986 and 1987, respectively. The operation of the upgraded JRR-3(JRR-3M) has started in March 1990 with the LEU aluminide fuels. Since May 1992, the two elements have been inserted in the KUR. The safety review application for the full core conversion to use LEU silicide in the JMTR was approved in February 1992 and the conversion has been done in January 1994. The Japanese Government approved a cancellation of the KUHFR Project in February 1991, and in April 1994 the U.S. Government gave an approval to utilize HEU in the KUR instead of the KUHFR. Therefore, the KUR will be operated with HEU fuel until 2001. Since March 1994, Kyoto University is continuing negotiation with UKAEA Dounreay on spent fuel reprocessing and blending down of recovered uranium, in addition to that with USDOE.

High plasma ghrelin protects from coronary heart disease and Leu72Leu polymorphism of ghrelin gene from cancer in healthy adults during the 19 years follow-up study.

Science.gov (United States)

Laurila, M; Santaniemi, M; Kesäniemi, Y A; Ukkola, O

2014-11-01

The aim of our investigation was to find out if ghrelin concentrations or polymorphisms predict the future risk for cardiovascular diseases and cancer in a population-based cohort initiated in 1991 (491 hypertensive and 513 control subjects). Total mortality and hospital events were followed up for 19 years. Fasting total ghrelin concentrations were determined and Arg51Gln, Leu72Met and -501 A > C polymorphisms identified. Cox regression analysis was performed. The mean value in the control cohort was 674 pg/ml whereas in the hypertensive cohort it was 661 pg/ml. The associations found suggest that in the controls the highest ghrelin quartile protected from CHD (coronary heart disease). The results were significant without or with adjustments for age, sex, smoking, systolic blood pressure and LDL cholesterol, BMI, type 2 diabetes or QUICK index. C/C variant of the promoter associated with the prevention of IHD (ischemic heart disease) in the hypertensive group (pghrelin concentration was related to protection from CHD and Leu72Leu genotype to prevention of cancer in healthy adults during the 19 years follow-up. C/C promoter protects from IHD in the hypertensive subjects. Copyright © 2014 Elsevier Inc. All rights reserved.

Waste Photovoltaic Panels for Ultrapure Silicon and Hydrogen through the Low-Temperature Magnesium Silicide.

Czech Academy of Sciences Publication Activity Database

Dytrych, Pavel; Bumba, Jakub; Kaštánek, František; Fajgar, Radek; Koštejn, Martin; Šolcová, Olga

Roč. 56, č. 45 ( 2017 ), s. 12863-12869 ISSN 0888-5885 R&D Projects: GA ČR GA15-14228S Institutional support: RVO:67985858 Keywords : magnesium silicide * waste photovoltaic panels * ultrapure silicon Subject RIV: CI - Industrial Chemistry, Chemical Engineering OBOR OECD: Chemical process engineering Impact factor: 2.843, year: 2016

Progress in doping of ruthenium silicide (Ru2Si3)

International Nuclear Information System (INIS)

Vining, C.B.; Allevato, C.E.

1992-01-01

This paper reports that ruthenium silicide (Ru 2 Si 3 ) is currently under development as a promising thermoelectric material suitable for space power applications. Key to realizing the potentially high figure of merit values of this material is the development of appropriate doping techniques. In this study, manganese and iridium have been identified as useful p- and n-type dopants, respectively. Resistivity values have been reduced by more than 3 orders of magnitude. Anomalous Hall effect results, however, complicate interpretation of some of the results and further effort is required to achieve optimum doping levels

Investigations of uraniumsilicide-based dispersion fuels for the use of low enrichment uranium (LEU) in research and test reactors

International Nuclear Information System (INIS)

Nazare, S.

1982-07-01

The work presents at the outset, a review of the preparation and properties of uranium silicides (U 3 Si and U 3 Si 2 ) in so far as these are relevant for their use as dispersants in research reactor fuels. The experimental work deals with the preparation and powder metallurgical processing of Al-clad miniature fuel element plates with U 3 Si- und U 3 Si-Al up to U-densities of 6.0 g U/cm 3 . The compatibility of these silicides with the Al-matrix under equilibrium conditions (873 K) and the influence of the reaction on the dimensional stability of the miniplates is described and discussed. (orig.) [de

Irradiation of an uranium silicide prototype in RA-3 reactor; Irradiacion de un elemento combustible prototipo de siliciuro de uranio en el RA-3

Energy Technology Data Exchange (ETDEWEB)

Calabrese, R; Estrik, G; Notari, C [Comision Nacional de Energia Atomica, San Martin (Argentina). Unidad de Actividad Reactores y Centrales Nucleares

1997-12-31

The factibility of irradiation of an uranium silicide (U{sub 3} Si{sub 2}) prototype in the RA-3 reactor was studied. The standard RA-3 fuel element uses U{sub 3} O{sub 8} as fissible material. The enrichment of both standard and prototype is the same: 20% U{sub 235} and also the frame geometry and number of plates is identical. The differences are in the plate dimensions and the fissile content which is higher in the prototype. The cooling conditions of the core allow the insertion of the prototype in any core position, even near the water trap, if the overall power is kept below 5Mw. Nevertheless, the recommendation was to begin irradiation near the periphery and later on move the prototype towards more central positions in order to increase the burnup rate. The prototype was effectively introduced in a peripheral position and the thermal fluxes were measured between plates with the foil activation technique. These were also evaluated with the fuel management codes and a reasonable agreement was found. (author). 5 refs., 3 figs., 3 tabs.

Material test reactor fuel research at the BR2 reactor

Energy Technology Data Exchange (ETDEWEB)

Dyck, Steven Van; Koonen, Edgar; Berghe, Sven van den [Institute for Nuclear Materials Science, SCK-CEN, Boeretang, Mol (Belgium)

2012-03-15

The construction of new, high performance material test reactor or the conversion of such reactors' core from high enriched uranium (HEU) to low enriched uranium (LEU) based fuel requires several fuel qualification steps. For the conversion of high performance reactors, high density dispersion or monolithic fuel types are being developed. The Uranium-Molybdenum fuel system has been selected as reference system for the qualification of LEU fuels. For reactors with lower performance characteristics, or as medium enriched fuel for high performance reactors, uranium silicide dispersion fuel is applied. However, on the longer term, the U-Mo based fuel types may offer a more efficient fuel alternative and-or an easier back-end solution with respect to the silicide based fuels. At the BR2 reactor of the Belgian nuclear research center, SCK-CEN in Mol, several types of fuel testing opportunities are present to contribute to such qualification process. A generic validation test for a selected fuel system is the irradiation of flat plates with representative dimensions for a fuel element. By flexible positioning and core loading, bounding irradiation conditions for fuel elements can be performed in a standard device in the BR2. For fuel element designs with curved plates, the element fabrication method compatibility of the fuel type can be addressed by incorporating a set of prototype fuel plates in a mixed driver fuel element of the BR2 reactor. These generic types of tests are performed directly in the primary coolant flow conditions of the BR2 reactor. The experiment control and interpretation is supported by detailed neutronic and thermal-hydraulic modeling of the experiments. Finally, the BR2 reactor offers the flexibility for irradiation of full size prototype fuel elements, as 200mm diameter irradiation channels are available. These channels allow the accommodation of various types of prototype fuel elements, eventually using a dedicated cooling loop to provide the

Loss-of-Flow and Loss-of-Pressure Simulations of the BR2 Research Reactor with HEU and LEU Fuel

Energy Technology Data Exchange (ETDEWEB)

Licht, J. [Argonne National Lab. (ANL), Argonne, IL (United States); Bergeron, A. [Argonne National Lab. (ANL), Argonne, IL (United States); Dionne, B. [Argonne National Lab. (ANL), Argonne, IL (United States); Sikik, E. [Belgian Nuclear Research Center (SCK-CEN), Mol (Belgium); Van den Branden, G. [Belgian Nuclear Research Center (SCK-CEN), Mol (Belgium); Koonen, E. [Belgian Nuclear Research Center (SCK-CEN), Mol (Belgium)

2016-01-01

Belgian Reactor 2 (BR2) is a research and test reactor located in Mol, Belgium and is primarily used for radioisotope production and materials testing. The Materials Management and Minimization (M3) Reactor Conversion Program of the National Nuclear Security Administration (NNSA) is supporting the conversion of the BR2 reactor from Highly Enriched Uranium (HEU) fuel to Low Enriched Uranium (LEU) fuel. The reactor core of BR2 is located inside a pressure vessel that contains 79 channels in a hyperboloid configuration. The core configuration is highly variable as each channel can contain a fuel assembly, a control or regulating rod, an experimental device, or a beryllium or aluminum plug. Because of this variability, a representative core configuration, based on current reactor use, has been defined for the fuel conversion analyses. The code RELAP5/Mod 3.3 was used to perform the transient thermal-hydraulic safety analyses of the BR2 reactor to support reactor conversion. The input model has been modernized relative to that historically used at BR2 taking into account the best modeling practices developed by Argonne National Laboratory (ANL) and BR2 engineers.

Neutronic feasibility studies using U-Mo dispersion fuel (9 Wt % Mo, 5.0 gU/cm3) for LEU conversion of the MARIA (Poland), IR-8 (Russia), and WWR-SM (Uzbekistan) research reactors

International Nuclear Information System (INIS)

Bretscher, M.M.; Deen, J.R.; Hanan, N.A.; Matos, E.

2000-01-01

U-Mo alloys dispersed in an Al matrix offer the potential for high-density uranium fuels needed for the LEU conversion of many research reactors. On-going fuel qualification tests by the US RERTR Program show good irradiation properties of U-Mo alloy dispersion fuel containing 7-10 weight percent molybdenum. For the neutronic studies in this paper the alloy was assumed to contain 9 wt % Mo (U-9Mo) with a uranium density in the fuel meat of 5.00 gU/cm 3 which corresponds to 32.5 volume % U-9Mo. Fuels containing U-9Mo have been used in Russian reactors since the 1950's. For the three research reactors analyzed here, LEU fuel element thicknesses are the same as those for the Russian-fabricated HEU reference fuel elements. Relative to the reference fuels containing 80-90% enriched uranium, LEU U-9Mo Al-dispersion fuel with 5.00 gU/cm 3 doubles the cycle length of the MARIA reactor and increases the IR-8 cycle length by about 11%. For the WWR-SM reactor, the cycle length, and thus the number of fuel assemblies used per year, is nearly unchanged. To match the cycle length of the 36% enriched fuel currently used in the WWR-SM reactor will require a uranium density in the LEU U-9Mo Al-dispersion fuel of about 5.4 gU/cm 3 . The 5.00 gU/cm 3 LEU fuel causes thermal neutron fluxes in water holes near the edge of the core to decrease by (6-8)% for all three reactors. (author)

The Leu72Met polymorphism of the GHRL gene prevents the development of diabetic nephropathy in Chinese patients with type 2 diabetes mellitus.

Science.gov (United States)

Zhuang, Langen; Li, Ming; Yu, Changhua; Li, Can; Zhao, Mingming; Lu, Ming; Zheng, Taishan; Zhang, Rong; Zhao, Weijing; Bao, Yuqian; Xiang, Kunsan; Jia, Weiping; Wang, Niansong; Liu, Limei

2014-02-01

The preproghrelin (GHRL) Leu72Met polymorphism (rs 696217) is associated with obesity, reduced glucose-induced insulin secretion in healthy or diabetic subjects, and reduced serum creatinine (Scr) levels in type 2 diabetes. We evaluated the association of the Leu72Met polymorphism with measures of insulin sensitivity in non-diabetic control individuals and type 2 diabetics, and whether this variation contributes to the development of diabetic nephropathy (DN) in type 2 diabetes. A case-control study was performed of 291 non-diabetic control subjects and 466 patients with type 2 diabetes, of whom 238 had DN with overt albuminuria (DN group; albuminuric excretion rate [AER] ≥ 300 mg/24 h) and 228 did not have DN, but had diabetes for more than 10 years (non-DN group). Genotyping was performed using a TaqMan PCR assay. The Leu/Leu, Leu/Met, and Met/Met genotype frequencies were significantly different between the non-DN and DN groups (p = 0.011). The frequency of the variant genotypes (Leu/Met, Met/Met) was significantly lower in the DN group than the non-DN group (23.5 vs. 36.0 %, p = 0.003). Met/Met non-diabetic control subjects had lower BMI and Scr levels and higher eGFR level than Leu/Leu or Leu/Met individuals (p GHRL Leu72Met polymorphism may help to maintain normal renal function and may protect against the development of DN by reducing albuminuria and improving renal function in Chinese patients with type 2 diabetes.

SMOPY, a new NDA tool for safeguards of LEU and MOX spent fuel

International Nuclear Information System (INIS)

Lebrun, A.; Merelli, M.; Szabo, J.-L.; Huver, M.; Arenas-Carrasco, J.

2001-01-01

Upon IAEA request, the French support program to IAEA Safeguards has developed a new device for control of the irradiated LEU and MOX fuels. The Safeguards Mox Python (SMOPY) is the achievement of a 4 years R and D program supported by CEA and COGEMA in partnership with Eurisys Mesures. The SMOPY system is based on the combination of 2 NDA techniques (passive neutron and room temperature gamma spectrometry) and on line interpretation tools (automatic gamma spectrum interpretation, depletion code EVO). Through the measurement managing software, all this contributes to the fully automatic measurement, interpretation and characterization of any kind of spent fuel. The device is transportable (50 kg, 60 cm) and is composed of four parts: 1. the measurement head with one high efficiency fission chamber and a micro room temperature gamma spectrometric probe; 2. the carrier which carries the measurement head. The carrier bottom fits the racks for accurate positioning and its top fits operator's fuel moving tool; 3. the portable electronic cabinet which includes both neutron and gamma electronic cards; 4. the portable PC which gets inspectors data, controls the measurement, get measured values, interprets them and immediately provides the inspector with worthwhile info for appropriate on the field decisions. Main features of SMOPY are: Discrimination of MOX versus LEU irradiated fuels in any case (conservative case is one cycle MOX versus three cycles LEU after short cooling time); Full characterization of irradiated LEU (burnup, cooling time, Pu amounts ...); Partial Defect Test on LEU fuels. A first version of SMOPY has been tested in industrial condition during summer 2000. This tests shown a need of shielding improvement around the gamma detector. A new version has been build a will be qualified during a new field test and then the system will be ready for routine operation in IAEA and commercial delivery. After giving details about the system itself, this paper