WorldWideScience

Sample records for weathering steel coupons

  1. The correlation between accelerated and field corrosion tests performed in carbon steel and weathering steel coupons, coated and non-coated; Correlacao entre ensaios acelerados e ensaios de campo em corpos-de-provas de aco carbono e aco patinavel, sem e com revestimento

    Energy Technology Data Exchange (ETDEWEB)

    Antunes, Renato Altobelli

    2002-07-01

    The performance of four different organic coating systems applied to carbon and weathering steel coupons has been assessed in this investigation. applied on the surface of carbon steel and weathering steel coupons. The coupons have been evaluated using five different tests, three field tests and two accelerated tests. The field tests were carried out at three atmospheric stations, located at COSIPA in Cubatao-SP, at Alto da Serra in Cubatao-SP and at Paula Souza in Sao Paulo city. The accelerated tests consisted of (a) exposure to alternate cycles of ultraviolet radiation/condensation combined with salt spray cycles (UVCON combined with Salt Spray) and of (b) exposure to alternate cycles of ultraviolet radiation/condensation combined with the Prohesion test. The performance of the coatings was assessed by visual observation and photographs, using a method based on ASTM D-610, ASTM D-714 and ASTM-1654 standards to rank them. The oxide phases formed on the surfaces of the non-coated specimens of carbon and weathering steels, exposed to the same tests performed with the coated specimens, were identified using three different techniques: X-ray diffraction, Raman microscopy and Moessbauer spectroscopy. In the field tests, the specimens have been exposed for 1, 2, 3, 6 and 9 months. In the accelerated ones, the results were obtained after 1340 hours (4 cycles) test. The main component identified in all the specimens collected from the field tests and from the UVCON combined with the Prohesion test was lepidocrocite ({gamma}-FeOOH). Goethite ({alpha}-FeOOH ) and magnetite (Fe{sub 3}O{sub 4}) were identified as the other two main phases present in ali the specimens. In the UVCON combined with Salt Spray test, the dominant phase was magnetite, followed by goethite and lepidocrocite. The morphology of the rust formed on the specimens was examined by scanning electron microscopy (SEM). Structures corresponding to goethite and lepidocrocited were recognized on ali specimens

  2. FISH DETECTION OF CAMPYLOBACTER AND ARCOBACTER ADHERED TO STAINLESS STEEL COUPONS

    Directory of Open Access Journals (Sweden)

    Lucie Šilhová

    2015-02-01

    Full Text Available This study focuses on detecting biofilm and planktonic bacterial cells of the genera Arcobacter and Campylobacter. This study is, to our knowledge, the first study deals with application of FISH procedure to detect biofilm formation on stainless steel coupons of Arcobacter-isolates from real-world environments. These bacteria can cause a lot of diseases. Especially, in the last decade, arcobacters have been increasingly isolated from feces of clinically healthy and ill animals, foods of animal origin and various types of water. Fluorescence in situ hybridization was used to detect biofilm and planktonic cells of selected microorganisms. This method was optimized and subsequently applied to biofilm samples prepared on stainless steel coupons. The study results indicate that fluorescence in situ hybridization is suitable for detecting biofilm and planktonic cells of the studied bacteria.

  3. Detection of Microbial sulfate-reduction associated with buried stainless steel coupons

    Energy Technology Data Exchange (ETDEWEB)

    Mark E. Delwiche; M. Kay Adler Flitton; Alicia Olson

    2007-03-01

    The objective of this study was to demonstrate applicability of an innovative radioactive isotope method for imaging microbial activity in geological materials to a comprehensive study of metal corrosion. The method was tested on a sample of stainless steel coupons that had been buried as part of a corrosion study initiated by the National Institute of Standards and Testing or NIST (known as National Bureau of Standards prior to 1988) in 1970. The images showed evidence of microbial activity that could be mapped on a millimeter scale to coupon surfaces. A second more conventional isotope tracer method was also used to provide a quantitative measure of the same type of microbial activity in soil proximal to the buried coupons. Together the techniques offer a method for evaluating low metabolic levels of activity that have the potential for significant cumulative corrosion effects. The methods are powerful tools for evaluation of potential for microbial induced corrosion to buried steel components used on pipelines, in the power and communications infrastructure, and in nuclear waste repository containers.

  4. Microbiota formed on attached stainless steel coupons correlates with the natural biofilm of the sink surface in domestic kitchens.

    Science.gov (United States)

    Moen, Birgitte; Røssvoll, Elin; Måge, Ingrid; Møretrø, Trond; Langsrud, Solveig

    2016-02-01

    Stainless steel coupons are frequently used in biofilm studies in the laboratory, as this material is commonly used in the food industry. The coupons are attached to different surfaces to create a "natural" biofilm to be studied further in laboratory trials. However, little has been done to investigate how well the microbiota on such coupons represents the surrounding environment. The microbiota on sink wall surfaces and on new stainless steel coupons attached to the sink wall for 3 months in 8 domestic kitchen sinks was investigated by next-generation sequencing (MiSeq) of the 16S rRNA gene derived from DNA and RNA (cDNA), and by plating and identification of colonies. The mean number of colony-forming units was about 10-fold higher for coupons than sink surfaces, and more variation in bacterial counts between kitchens was seen on sink surfaces than coupons. The microbiota in the majority of biofilms was dominated by Moraxellaceae (genus Moraxella/Enhydrobacter) and Micrococcaceae (genus Kocuria). The results demonstrated that the variation in the microbiota was mainly due to differences between kitchens (38.2%), followed by the different nucleic acid template (DNA vs RNA) (10.8%), and that only 5.1% of the variation was a result of differences between coupons and sink surfaces. The microbiota variation between sink surfaces and coupons was smaller for samples based on their RNA than on their DNA. Overall, our results suggest that new stainless steel coupons are suited to model the dominating part of the natural microbiota of the surrounding environment and, furthermore, are suitable for different downstream studies.

  5. Examination of the 1970 National Bureau of Standards Underground Corrosion Test Welded Stainless STeel Coupons from Site D

    Energy Technology Data Exchange (ETDEWEB)

    L. R. Zirker; M. K. Adler Flitton; T. S. Yoder; T. L. Trowbridge

    2008-01-01

    A 1970 study initiated by the National Bureau of Standards (NBS), now known as the National Institute of Standards and Technology (NIST), buried over 6000 corrosion coupons or specimens of stainless steel Types 201, 202, 301, 304, 316, 409, 410, 430, and 434. The coupons were configured as sheet metal plates, coated plates, cross-welded plates, U-bend samples, sandwiched materials, and welded tubes. All coupons were of various heat-treatments and cold worked conditions and were buried at six distinctive soil-type sites throughout the United States. The NBS scientists dug five sets of two trenches at each of the six sites. In each pair of trenches, they buried duplicate sets of stainless steel coupons. The NBS study was designed to retrieve coupons after one year, two years, four years, eight years, and x years in the soil. During the first eight years of the study, four of five planned removals were completed. After the fourth retrieval, the NBS study was abandoned, and the fifth and final set of specimens remained undisturbed for over 33 years. In 2003, an interdisciplinary research team of industrial, university, and national laboratory investigators were funded under the United States Department of Energy’s Environmental Management Science Program (EMSP; Project Number 86803) to extract part of the remaining set of coupons at one of the test sites, characterize the stainless steel underground corrosion rates, and examine the fate and transport of metal ions into the soil. Extraction of one trench at one of the test sites occurred in April 2004. This report details only the characterization of corrosion found on the 14 welded coupons–two cross welded plates, six U-bends, and six welded tubes–that were retrieved from Site D, located near Wildwood, NJ. The welded coupons included Type 301, 304, 316, and 409 stainless steels. After 33 years in the soil, corrosion on the coupons varied according to alloy. This report discusses the stress corrosion cracking and

  6. Inactivation Kinetics and Mechanism of a Human Norovirus Surrogate on Stainless Steel Coupons via Chlorine Dioxide Gas.

    Science.gov (United States)

    Yeap, Jia Wei; Kaur, Simran; Lou, Fangfei; DiCaprio, Erin; Morgan, Mark; Linton, Richard; Li, Jianrong

    2015-10-16

    Acute gastroenteritis caused by human norovirus is a significant public health issue. Fresh produce and seafood are examples of high-risk foods associated with norovirus outbreaks. Food contact surfaces also have the potential to harbor noroviruses if exposed to fecal contamination, aerosolized vomitus, or infected food handlers. Currently, there is no effective measure to decontaminate norovirus on food contact surfaces. Chlorine dioxide (ClO2) gas is a strong oxidizer and is used as a decontaminating agent in food processing plants. The objective of this study was to determine the kinetics and mechanism of ClO2 gas inactivation of a norovirus surrogate, murine norovirus 1 (MNV-1), on stainless steel (SS) coupons. MNV-1 was inoculated on SS coupons at the concentration of 10(7) PFU/coupon. The samples were treated with ClO2 gas at 1, 1.5, 2, 2.5, and 4 mg/liter for up to 5 min at 25°C and a relative humidity of 85%, and virus survival was determined by plaque assay. Treatment of the SS coupons with ClO2 gas at 2 mg/liter for 5 min and 2.5 mg/liter for 2 min resulted in at least a 3-log reduction in MNV-1, while no infectious virus was recovered at a concentration of 4 mg/liter even within 1 min of treatment. Furthermore, it was found that the mechanism of ClO2 gas inactivation included degradation of viral protein, disruption of viral structure, and degradation of viral genomic RNA. In conclusion, treatment with ClO2 gas can serve as an effective method to inactivate a human norovirus surrogate on SS contact surfaces.

  7. Fatigue Strength of Weathering Steel

    Directory of Open Access Journals (Sweden)

    Ludvík KUNZ

    2012-03-01

    Full Text Available Fatigue behaviour of Atmofix 52 steel (comparable to COR-TENâ steel exposed to atmospheric corrosion for 20 years was investigated. S-N curves for load symmetrical cycling and cycling with stress ratio R = 0 were determined on specimens detracted from a failed transmission tower. The data were compared with those on material without a rust layer. The fracture surfaces and, in particular, the sites of fatigue crack initiation were analyzed. Substantial decrease of fatigue life and fatigue limit due to corrosion exposition was found. Based on observation of surface layer with corrosion products and on fractographic analysis of failed specimens conclusions on fatigue damage mechanism were drawn. No grain boundary corrosion, which can be responsible for fatigue crack initiation, was observed. Initiation of fatigue cracks was related to surface roughness and took place exclusively on corrosion dimples.DOI: http://dx.doi.org/10.5755/j01.ms.18.1.1335

  8. Atmospheric Corrosion of Q235 Carbon Steel and Q450 Weathering Steel in Turpan,China

    Institute of Scientific and Technical Information of China (English)

    Qiang YU; Chao-fang DONG; Yue-hua FANG; Kui XIAO; Chun-yun GUO; Gang HE; Xiao-gang LI

    2016-01-01

    Q235 carbon steel and Q450 weathering steel were exposed to the hot and dry environment of Turpan, China for three years.The corrosion rates of both steels were calculated and compared.The morphologies of the rust layer products were observed by optical microscopy and scanning electron microscopy.Analyses of the rust layers were performed by X-ray photoelectron spectroscopy,X-ray powder diffraction,and Raman spectroscopy,and anal-ysis results indicate that the compositions of rust are main iron rich oxide such as FeOOH,Fe3 O4 ,and Fe2 O3 .The iron oxide layer content proportion was calculated through a semi-quantitative algorithm.The resistance elements (Cr,Ni,and Cu)enhanced the resistance properties of the Q450 weathering steel matrix.Moreover,the resistance elements increased the proportion of goethite crystals in the corroded rust layer.

  9. Coupon Surveillance For Corrosion Monitoring In Nuclear Fuel Basin

    Energy Technology Data Exchange (ETDEWEB)

    Mickalonis, J. I.; Murphy, T. R.; Deible, R.

    2012-10-01

    Aluminum and stainless steel coupons were put into a nuclear fuel basin to monitor the effect of water chemistry on the corrosion of fuel cladding. These coupons have been monitored for over ten years. The corrosion and pitting data is being used to model the kinetics and estimate the damage that is occurring to the fuel cladding.

  10. Corrosion Behavior of S450EW Low-alloy Weathering Steel in Cyclically Alternate Corrosion Environments

    Institute of Scientific and Technical Information of China (English)

    Jun-shan WANG; Pei-yang SHI; Cheng-jun LIU; Mao-fa JIANG

    2015-01-01

    Weathering steel is widely used in various ifelds due to its excellent mechanical properties and high corrosion resistance. The effect of chromium content on the S450EW weathering steel in cyclic immersion test was studied. The results indicated that the corrosion resistance of S450EW weathering steel is closely related to chromium content. The addition of chromium signiif-cantly inhibited the weathering steel corrosion. The corrosion rate of experimental steel after 96 h immersion was 1.101 g·m−2·h−1. The rust of S450EW weathering steel was mainly constituted of FeOOH and Fe3O4 phase, and the elevation of chromium content promoted the formation of α-FeOOH. The ifne precipitates of the two phases contributed to the formation of dense dust layer of test steel. Furthermore, the increase of chromium is beneifcial for the cure of original defects and cracks of the rust layer via the enrich-ment of chromium. The corrosion potential and the resistance of corrosion process were thus increased, protecting the experimental steel from further corrosion. A S450EW steel with corrosion resistance more than 1.5 times of Q450NQR1 steel was prepared.

  11. Effects of rare earth on inclusions and corrosion resistance of 10PCuRE weathering steel

    Institute of Scientific and Technical Information of China (English)

    YUE

    2010-01-01

    The types,morphologies and distributions of nonmetallic inclusions in Cu-P weathering steels with and without rare earth were analyzed through a quantitative image analyzer,scanning electron microscopy(SEM)and energy dispersive spectroscopy(EDS)attached to SEM.Solid-soluble content of rare earth in the steels was analyzed by non-aqua electroanalysis and ICP.The results showed that rare earth modified the types and the morphologies of inclusions in the weathering steels.The small spherical rare earth oxysulfides and rare earth sulphides replaced the elongated MnS inclusions in the RE weathering steels.The rare earth inclusions dispersedly distributed and most inclusions were smaller than 2 μm in size.The optimum content of RE was 0.0065%-0.016% for 10PCuRE weathering steels containing about0.002% oxygen and 0.004% sulfur.Solid-soluble content of rare earth in steels was(14-20)x 10-6,which can act as a micro-alloying element.The corrosion resistance of 10PCuRE weathering steels and Q235 were studied by dry-wet cyclic immersion test.Their corrosion rates were obtained respectively.The polarization curves and pitting corrosion behaviors of weathering steels with and without rare earth were measured by electrochemical methods.The corrosion resistance of Cu-P weathering steels was improved by adding an appropriate amount of rare earth.Less and fewer rare earth inclusions largely decreased pitting susceptibility and rate of pit propagation.The pitting potential and the resistance against pitting corrosion of the RE weathering steel were significantly improved due to the modification of rare earth to inclusions.

  12. Simulation of a long term atmospheric corrosion process on plain and weathering steels

    OpenAIRE

    Bolivar, F.; Morales, A.; Arroyave, C.

    2003-01-01

    Information on weathering steel behaviour and its rust products characteristics after decades of atmospheric exposure are scarce. On the other side, generally accepted laboratory tests for the assessment of its corrosion resistance have not been developed yet. Consequently, simulating corrosion in the laboratory during long periods of time is attractive for the interesting and complete information obtainable from them. In the present work, AISI-SAE 1008 and ASTM-588 B steel samples have been ...

  13. 7 CFR 274.7 - Coupon management.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 4 2010-01-01 2010-01-01 false Coupon management. 274.7 Section 274.7 Agriculture... FOOD STAMP AND FOOD DISTRIBUTION PROGRAM ISSUANCE AND USE OF COUPONS § 274.7 Coupon management. (a) Coupon inventory management. State agencies shall establish coupon inventory management systems...

  14. Tropical Weather Resistant Galvanized Steel Coated and Uncoated

    Directory of Open Access Journals (Sweden)

    Suárez-Corrales Xenia Isbel

    2014-01-01

    Full Text Available The corrosion behavior of coated and uncoated galvanized steel products is determined by exposing them to accelerated and natural climatic test. Accelerated tests were carried out in climatic chambers and natural atmospheric test in a marine-coastal station (Cojimar. The influence of tropical humid climate on these products is determined. Adhesion is an important property for a good performance, from the decorative point of view or as an additional protection. The evaluation indicates that 95% of the galvanized steel products show a good corrosion resistance; although 71% of coated galvanized products and 100% of painted galvanized products do not cover the requirements with respect to the mechanical and corrosion protection aspects. For a good efficiency and economic performance of metal mechanical industry, a correct surface treatment and coating application is required. A key point is to increase the quality by improving a better corrosion protective performance respecting uncoated galvanized steel.

  15. In situ Colonization of Marine Biofilms on UNS S32760 Duplex Stainless Steel Coupons in Areas with Different Water Qualities:Implications for Corrosion Potential Behavior

    Institute of Scientific and Technical Information of China (English)

    Luciana VR de Messano; Barbara LIgnacio; Maria HCB Neves; Ricardo Coutinho

    2014-01-01

    In the presence of biofilms, stainless steels (SS) exhibits an increase in corrosion potential, called ennoblement. In the present study, the corrosion potential (Ecor ) behavior of the duplex SS UNS S32760 was recorded simultaneously with the in situ marine biofilm formation in two areas at Arraial do Cabo, Southeastern Brazil. The biofilm at Forno Harbor (an anthropogenically disturbed area) was characterized by higher relative abundances of Bacteria at day 2, followed by diatoms (especially Navicula sp.) on day 10 and dinoflagellates on day 18, whereas no clear trend was recorded at Cabo Frio Island (an undisturbed area). The ennoblement of Ecor values was site-dependent. In a complementary laboratory assay, biofilms were removed and the Ecor values registered in sterile conditions for the subsequent 10 days and corroborated in situ results. Understanding biofilms and SS interactions has important implications for materials science and engineering decisions as well as helping to fill in important gaps in this knowledge.

  16. Suppression of deicing salt corrosion of weathering steel bridges by washing

    Energy Technology Data Exchange (ETDEWEB)

    Hara, Shuichi [Investigation and Research Division, Sumitomo Metal Technology Inc., 1-8 Fuso-cho, Amagasaki, Hyogo 660-0891 (Japan)]. E-mail: hara-shu@smt-co.com; Miura, Masazumi [Development Division, Yon-den Consultant Co., 1007-3 Mure-cho Kida-gun, Kagawa 761-0121 (Japan); Uchiumi, Yasushi [Bridge Division, Kawada Industries Inc., 1-3-11 Takinogawa, Kita-ku, Tokyo 114-8562 (Japan); Fujiwara, Toshiaki [Takamatsu Engineering Office, Shikoku Regional Bureau, Japan Highway Public Co., 4-1-3 Asahi-cho, Takamatsu, Kagawa 760-0065 (Japan); Yamamoto, Masataka [Takamatsu Engineering Office, Shikoku Regional Bureau, Japan Highway Public Co., 4-1-3 Asahi-cho, Takamatsu, Kagawa 760-0065 (Japan)

    2005-10-01

    To elucidate the influences of deicing salts and high pressure (2-4 MPa) washing on the characteristics of the rust formed on weathering steel bridges, washing experiments have been carried out for three years. The rust was characterized by means of ion chromatography, X-ray diffraction and adsorption of N{sub 2}. The rust thickness was measured, and also the rust weight per unit area of the steel surface was measured. It was found that water-soluble chloride accelerated the rate of corrosion because the rust particles grow by the chloride ions and micro-pore structure of the rust appeared by the chloride ions. Washing with water suppressed corrosion owing to the disappearance of chloride ions.

  17. Abnormal relationship between rust particles size and rust layer compactness of weathering steels

    Institute of Scientific and Technical Information of China (English)

    2010-01-01

    In order to reveal evolution of the rust layer during atmospheric corrosion,commercial weathering steel(WS) 09CuPCrNi and a recently developed bainite WS were subjected to a salt fog test.The protection and compactness of the rust layer were evaluated by electrochemical analysis,absorption-desorption test,etc.The experimental results indicate that more compact rust layer could be derived from the rust particles with larger size.The well-established notion that the rust particle growth can induce the decreme...

  18. Dynamic Recrystallization and Precipitation Behavior of Mn-Cu-V Weathering Steel

    Institute of Scientific and Technical Information of China (English)

    Hongyan Wu; Linxiu Du; Xianghua Liu

    2011-01-01

    The hot deformation behavior of a Mn-Cu-V weathering steel was investigated at temperatures ranging from 850 to 1050℃ and strain rates ranging from 0.01 to 5 s-1 using MMS-300 thermal-mechanical simulator. The activation energy for dynamic recrystallization and stress exponent were calculated to be 551 kJ/mol and 7.73, respectively. The accurate values of critical strain were determined by the relationship between work hardening rate and flow stress (θ-σ) curves. The hyperbolic sine constitutive equation was employed to describe the relationship between the peak stress and Zener-Hollomon parameter during hot deformation. The interaction between dynamic recrystallization and dynamic precipitation of V(C,N) at a low strain rate was analyzed. The results showed that precipitation particles size of weathering steel increased with increasing strain at deformation temperature 950℃ and strain rate 0.1 s-1. The calculation results of the recrystallization driving force and pinning force showed that dynamic precipitation could retard the progress of dynamic recrystallization but not prevent it while the pinning forces is less than driving force. On the contrary, dynamic precipitation can effectively prevent the progress of dynamic recrystallization.

  19. Effects of Alloy Element and Microstructure on Corrosion Resistant Property of Deposited Metals of Weathering Steel

    Institute of Scientific and Technical Information of China (English)

    Xiao-ming XIAO; Yun PENG; Cheng-yong MA; Zhi-ling TIAN

    2016-01-01

    Alloy element and microstructure are key factors that dominate mechanical and corrosion resistant properties of weathering steel.The effect of Mo on microstructure,mechanical properties and corrosion resistant property of depos-ited metal was investigated.Experimental results show that with the increase of Mo content in deposited metals,the phase transformation temperature decreases,and the ferrite zone in CCT diagram moves rightward,resulting in en-larged bainite zone and reduced ferrite and pearlite zone.The addition of 0�24 mass% Mo in deposited metal results in the increase of tensile strength,more M-A constituent and less high angle grain which reduce the low temperature toughness.It is found that Mo can raise the weathering resistance of deposited metal in industrial atmosphere.Analy-sis indicates that Mo may enrich in the inner rust layer,produce MoO3 ,enhance the formation of compact rust film and impede the anode dissolution reaction.Granular bainite in deposited metals displays better corrosion resistance than acicular ferrite during the initial corrosion stage,but its long-term influence on the corrosion resistance is limited.

  20. Furniture Rack Corrosion Coupon Surveillance - 2012 Update

    Energy Technology Data Exchange (ETDEWEB)

    Mickalonis, J. I.; Murphy, T. R.; Berry, C. J.

    2012-10-01

    Under the L Basin corrosion surveillance program furniture rack coupons immersed for 14 years (FY2009 coupons) and 16 years (FY2011 coupons) were analyzed and the results trended with coupons exposed for shorter times. In addition, a section harvested from an actual furniture rack that was immersed for 14 years was analyzed for pitting in the weld and heat-affected-zone (HAZ) regions. The L Basin operations maintained very good water quality over the entire immersion period for these samples. These results for FY2009 and FY2011 coupons showed that the average pit depths for the 6061 and 6063 base metal are 1 and 2 mils, respectively, while those for the weld and HAZ are 3 and 4 mils, respectively. The results for the weld and HAZ regions are similar to coupons removed during the period of FY2003 to FY2007. These similarities indicate that the pit development occurred quickly followed by slow kinetics of increase in pit depth. For the actual furniture rack sample average pits of 5 and 2 mils were measured for the HAZ and weld, respectively. These results demonstrate that pitting corrosion of the aluminum furniture racks used to support the spent fuel occurs in waters of good quality. The corrosion kinetics or pit depth growth rate is much less that 1 mil/year, and would not impact long-term use of this material system for fuel storage racks in L Basin if good water quality is maintained.

  1. Immobilization of lead by application of soil amendment produced from vinegar residue, stainless steel slag, and weathered coal.

    Science.gov (United States)

    Pei, Guangpeng; Li, Yuxin; Zhu, Yuen; Shi, Weiyu; Li, Hua

    2017-08-11

    This paper presents a new soil amendment used for immobilization of soil Pb, produced from vinegar residue, stainless steel slag, and weathered coal. The pH value measuring, granulation and adsorption experiments were carried out to determine the optimal composition of soil amendment. Optimizing soil amendment B2 was composed of vinegar residue, weathered coal (humic acid 61.53 wt%), and stainless steel slag with the ratio of 80∶16∶4, and particle size was in the range of 2-4 mm. In the leaching column experiment, B2 addition reduced the Pb release from the soil as well as increasing leachate pH and decreasing the bioavailable Pb concentration. The leachate Pb concentration decreased with lengthened leaching time under lower pH, but such a phenomenon disappeared in the rebounding period. Compared to control, the DTPA extractable Pb content in soil decreased by 12.41, 13.20, and 8.78% with the B2 addition amount of 1.00, 2.00, and 2.00 wt%, respectively. In addition, the total Pb content of each soil layer generally rose as B2 addition increased. It was concluded that application of B2 led to lower transport and transformation of Pb in soil. Based on the single chemical extraction, the environmental risk of Pb was decreased after application of B2. Meanwhile, soil amendment was also a new way to recycle vinegar residue, stainless steel slag, and weathered coal.

  2. How retailer coupons increase attitudinal loyalty –

    DEFF Research Database (Denmark)

    Wierich, Ralf; Zielke, Stephan

    2014-01-01

    Purpose – The aim of this paper is to investigate how different design elements of retailer coupons increase the attitudinal loyalty towards retailers. Design/methodology/approach – Three design elements are manipulated in a 2x2x2 experimental design. Data is analysed using structural equation...... that personalization offers opportunities for increasing loyalty without the necessity of large investments. As these effects can occur without redemption, coupon promotions should not be evaluated based on redemption rates only. Originality/value – The study extends existing research by focusing on retailer coupons...... and the minimum purchase amount require at least some cognitive processing to have a loyalty impact. Research limitations/implications – Future studies can use the developed framework to test the impact of other design elements, promotion types or loyalty schemes. Practical implications – The results underline...

  3. Rust Layer Formed on Low Carbon Weathering Steels with Different Mn, Ni Contents in Environment Containing Chloride Ions

    Directory of Open Access Journals (Sweden)

    Gui-qin FU

    2016-11-01

    Full Text Available The rusting evolution of low carbon weathering steels with different Mn, Ni contents under a simulated environment containing chloride ions has been investigated to clarify the correlation between Mn, Ni and the rust formed on steels. The results show that Mn contents have little impact on corrosion kinetics of experimental steels. Content increase of Ni both enhances the anti-corrosion performance of steel substrate and the rust. Increasing Ni content is beneficial to forming compact rust. Semi-quantitative XRD phase analysis shows that the quantity ratio of α/γ*(α-FeOOH/(γ-FeOOH+Fe3O4 decreases as Mn content increases but it increases as Ni content increases. Ni enhances rust layer stability but Mn content exceeding 1.06 wt.% is disadvantageous for rust layer stability. The content increase of Mn does not significantly alter the parameters of the polarization curve. However, as Ni contents increases, Ecorr has shifted to the positive along with decreased icorr values indicating smaller corrosion rate especially as Ni content increases from 0.42 wt.% to 1.50 wt.%.DOI: http://dx.doi.org/10.5755/j01.ms.22.4.12844

  4. Simulation of a long term atmospheric corrosion process on plain and weathering steels

    Directory of Open Access Journals (Sweden)

    Bolivar, F.

    2003-12-01

    Full Text Available Information on weathering steel behaviour and its rust products characteristics after decades of atmospheric exposure are scarce. On the other side, generally accepted laboratory tests for the assessment of its corrosion resistance have not been developed yet. Consequently, simulating corrosion in the laboratory during long periods of time is attractive for the interesting and complete information obtainable from them. In the present work, AISI-SAE 1008 and ASTM-588 B steel samples have been exposed for two years to a immersion-emersion CEBELCOR type test in the laboratory, simulating a moderate urban atmosphere. Two groups of six samples each were tested. After the first year, three samples of each batch were retired for analysis and the rest was kept until they reached two years of exposure. The half cell electrode potentials were measured daily. The rust was characterized by metallographic techniques, Mossbauer spectroscopy (MS, Fourier transform infrared spectroscopy (FTIR, and X-ray diffraction (XRD. Comparison was done with field exposure experiments reported in the literature, and conclusions on the behaviour of tested samples were drawn looking for differences and similarities with samples and structures under actual atmospheric conditions.

    La información sobre el comportamiento y las características de los productos de corrosión de los aceros auto protectores, después de varias décadas de exposición a la atmósfera, es escasa. Por otra parte, aún no se han desarrollado ensayos de laboratorio de aceptación general para evaluar su resistencia a la corrosión. En consecuencia, cada día toman más importancia los ensayos de laboratorio durante largos periodos de exposición. En el presente trabajo, se sometieron muestras de acero AISI-SAE 1008 y ASTM 588-B, durante dos años, a un ensayo de laboratorio de inmersión-emersión tipo CEBELCOR. Se ensayaron dos grupos de seis muestras de cada composición de acero, en una

  5. Mössbauer and XRD analysis of corrosion products on weathering steel treated by wet-dry cycles using various solutions

    Science.gov (United States)

    Oyabu, Matashige; Nomura, Kiyoshi; Koike, Yuya; Okazawa, Atsushi

    2016-12-01

    Weathering steels (COR-TEN) were corroded by wet-dry cycles using a splay of various solutions in a laboratory. Corrosion products on weathering steel were characterized by X-ray diffractometry and Mössbauer spectrometry at room and low temperatures. Fine α-FeOOH, γ-FeOOH and γ-Fe 2 O 3 are fundamentally formed in various atmospheric conditions. β-FeOOH is additionally formed under the existence of chloride ions, but not formed when sulfate ions are coexisting. Spraying a NaF solution prevents the progress of corrosion.

  6. Mössbauer and XRD analysis of corrosion products on weathering steel treated by wet-dry cycles using various solutions

    Energy Technology Data Exchange (ETDEWEB)

    Oyabu, Matashige; Nomura, Kiyoshi, E-mail: dqf10204@nifty.com [Kanazawa Institute of Technology (Japan); Koike, Yuya [Meiji University, Department of Applied Chemistry (Japan); Okazawa, Atsushi [The University of Tokyo, School of Arts and Sciences (Japan)

    2016-12-15

    Weathering steels (COR-TEN) were corroded by wet-dry cycles using a splay of various solutions in a laboratory. Corrosion products on weathering steel were characterized by X-ray diffractometry and Mössbauer spectrometry at room and low temperatures. Fine α-FeOOH, γ-FeOOH and γ-Fe {sub 2}O{sub 3} are fundamentally formed in various atmospheric conditions. β-FeOOH is additionally formed under the existence of chloride ions, but not formed when sulfate ions are coexisting. Spraying a NaF solution prevents the progress of corrosion.

  7. Weathering steel as a potential source for metal contamination: Metal dissolution during 3-year of field exposure in a urban coastal site.

    Science.gov (United States)

    Raffo, Simona; Vassura, Ivano; Chiavari, Cristina; Martini, Carla; Bignozzi, Maria C; Passarini, Fabrizio; Bernardi, Elena

    2016-06-01

    Surface and building runoff can significantly contribute to the total metal loading in urban runoff waters, with potential adverse effects on the receiving ecosystems. The present paper analyses the corrosion-induced metal dissolution (Fe, Mn, Cr, Ni, Cu) from weathering steel (Cor-Ten A) with or without artificial patinas, exposed for 3 years in unsheltered conditions at a marine urban site (Rimini, Italy). The influence of environmental parameters, atmospheric pollutants and surface finish on the release of dissolved metals in rain was evaluated, also by means of multivariate analysis (two-way and three-way Principal Component Analysis). In addition, surface and cross-section investigations were performed so as to monitor the patina evolution. The contribution provided by weathering steel runoff to the dissolved Fe, Mn and Ni loading at local level is not negligible and pre-patination treatments seem to worsen the performance of weathering steel in term of metal release. Metal dissolution is strongly affected by extreme events and shows seasonal variations, with different influence of seasonal parameters on the behaviour of bare or artificially patinated steel, suggesting that climate changes could significantly influence metal release from this alloy. Therefore, it is essential to perform a long-term monitoring of the performance, the durability and the environmental impact of weathering steel.

  8. Coupons for Success: A Marketing Incentive in Academic Support

    Science.gov (United States)

    Potacco, Donna R.; Chen, Peter; Desroches, Danielle; Chisholm, Daniel R.; De Young, Sandra

    2013-01-01

    How does a Coupon Incentive Program motivate students to seek academic support in high-risk courses? Results from this study demonstrated that the Coupon Incentive Program was effective in motivating voluntary student attendance and improving student outcomes. Recommendations related to implementation of the Coupon Incentive Program are discussed.…

  9. Coupons for Success: A Marketing Incentive in Academic Support

    Science.gov (United States)

    Potacco, Donna R.; Chen, Peter; Desroches, Danielle; Chisholm, Daniel R.; De Young, Sandra

    2013-01-01

    How does a Coupon Incentive Program motivate students to seek academic support in high-risk courses? Results from this study demonstrated that the Coupon Incentive Program was effective in motivating voluntary student attendance and improving student outcomes. Recommendations related to implementation of the Coupon Incentive Program are discussed.…

  10. Corrosion of mild steel and stainless steel by marine Vibrio sp.

    Digital Repository Service at National Institute of Oceanography (India)

    PrabhaDevi; Wagh, A.B.

    Microbially induced corrosion (MIC) of stainless steel and mild steel coupons exposed to media with and without a bacterial culture Vibrio sp. was studied using Scanning Electron Microscope (SEM). Pitting type of corrosion was noticed which was more...

  11. Coupons from Deal Sites as Gifts

    DEFF Research Database (Denmark)

    Pavlicek, Antonin; Sudzina, Frantisek

    2017-01-01

    There already exist studies on what influences use of deal sites. But there is a gap in literature when it comes to purchasing coupons from deal sites and then using them as gifts. The paper analyzes whether gender, age and personality traits influence such behavior. Big Five Inventory traits and...... and narcissism were used. The impact of age was significant. Significance of agreeableness and of narcissism were somewhat above cutoff value 0.05, therefore borderline significant. All of them have positive effect....

  12. CORROSION BEHAVIORS OF THE EXPOSED SIDE AND UNDERSIDE OF LOW ALLOY WEATHERING STEEL IN QINGDAO AND WANNING FOR 18 MONTHS

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    For 18 months, a newly developed low alloy weathering steel has been exposed in two coastal sites (Qingdao in the north China, Wanning in the south China). The different corrosion behaviors of the exposed side and the underside of the samples were characterized by X-ray diffraction (XRD), polarization curve, electrochemical impedance spectroscopy (EIS), scanning electron microscopy (SEM), and N2 adsorp-tion approach. It was found that the samples exhibited higher corrosion rate in Wan-ning than that in Qingdao. The underside of the samples corrodes more seriously than the exposed side in Qingdao, whereas the result in Wanning is just the reverse.The protection performance of rust layers mainly depends on its compactness and the enrichment of Cu and Cr is a secondary causation. The different compactness of rust layers in the exposed side and the underside originates from different corrosion conditions of the two sides.

  13. An Architecture for Anonymous Mobile Coupons in a Large Network

    Directory of Open Access Journals (Sweden)

    Alberto Bartoli

    2016-01-01

    Full Text Available A mobile coupon (m-coupon can be presented with a smartphone for obtaining a financial discount when purchasing a product or a service. M-coupons are a powerful marketing tool that has enjoyed a huge growth and diffusion, involving tens of millions of people each year. We propose an architecture which may enable significant improvements over current m-coupon technology, in terms of acceptance of potential customers and of marketing actions that become feasible: the customer does not need to install any dedicated app; an m-coupon is not bound to any specific device or customer; an m-coupon may be redeemed at any store in a set of potentially many thousands of stores, without any prior arrangement between customer and store. We are not aware of any proposal with these properties.

  14. Coupon Redemption and Its Effect on Household Cheese Purchases

    OpenAIRE

    Dong, Diansheng; Kaiser, Harry M.

    2003-01-01

    By endogenizing unit value and coupon redemption, we estimate U.S. household cheese purchase, quality choice, and coupon redemption equations simultaneously. Zero purchases and missing values are taken into account in the model to correct for the selectivity bias. The correlations among the three equations are found to be significant. Empirical findings show that high quality choice significantly decreases cheese purchases, while cheese coupon usage significantly increases purchases. We find ...

  15. Measurements of residual stress in fracture mechanics coupons

    Energy Technology Data Exchange (ETDEWEB)

    Prime, Michael B [Los Alamos National Laboratory; Hill, Michael R [U.C. DAVIS; Nav Dalen, John E [HILL ENGINEERING

    2010-01-01

    This paper describes measurements of residual stress in coupons used for fracture mechanics testing. The primary objective of the measurements is to quantify the distribution of residual stress acting to open (and/or close) the crack across the crack plane. The slitting method and the contour method are two destructive residual stress measurement methods particularly capable of addressing that objective, and these were applied to measure residual stress in a set of identically prepared compact tension (C(T)) coupons. Comparison of the results of the two measurement methods provides some useful observations. Results from fracture mechanics tests of residual stress bearing coupons and fracture analysis, based on linear superposition of applied and residual stresses, show consistent behavior of coupons having various levels of residual stress.

  16. Corrosion of mild steel, copper and brass in crude oil / seawater mixture

    Digital Repository Service at National Institute of Oceanography (India)

    PrabhaDevi, S.; Sawant, S.S.; Wagh, A.B.

    Mild steel, copper and brass coupons were introduced in natural seawater containing varying amount of crude oil. Mild steel showed higher rate of corrosion in seawater containing oil and lower corrosion rate in natural as well as artificial seawater...

  17. Investigating the Relationship between Coupon Collecting and Top-of-Mind Brand Awareness.

    Science.gov (United States)

    Pokrywczynski, Jim

    To determine if coupon collecting has any influence on product information processing like brand awareness, and to understand better the coupon collecting process, an exploratory study examined the relationship between coupon-collecting behavior and brand awareness for the coupons collected. Subjects, 152 randomly chosen respondents from a Midwest…

  18. The effect of metal microstructure on the initial attachment of Escherichia coli to 1010 carbon steel.

    Science.gov (United States)

    Javed, M A; Stoddart, P R; McArthur, S L; Wade, S A

    2013-09-01

    Metallurgical features have been shown to play an important role in the attachment of microorganisms to metal surfaces. In the present study, the influence of the microstructure of as-received (AR) and heat-treated (HT) 1010 carbon steel on the initial attachment of bacteria was investigated. Heat treatment was carried out with the aim of increasing the grain size of the carbon steel coupons. Mirror-polished carbon steel coupons were immersed in a minimal medium inoculated with Escherichia coli (ATCC 25922) to investigate the early (15, 30 and 60 min) and relatively longer-term (4 h) stages of bacterial attachment. The results showed preferential colonisation of bacteria on the grain boundaries of the steel coupons. The bacterial attachment to AR steel coupons was relatively uniform compared to the HT steel coupons where an increased number of localised aggregates of bacteria were found. Quantitative analysis showed that the ratio of the total number of isolated (i.e., single) bacteria to the number of bacteria in aggregates was significantly higher on the AR coupons than the HT coupons. Longer-term immersion studies showed production of extracellular polymeric substances by the bacteria and corrosion at the grain boundaries on both types of steel coupon tested.

  19. A Modified Constant-Stress Coupon for Enhanced Natural Crack Start during Fatigue Testing

    Science.gov (United States)

    2016-05-01

    UNCLASSIFIED UNCLASSIFIED A Modified Constant- Stress Coupon for Enhanced Natural Crack Start during Fatigue Testing Witold Waldman, Robert...modified constant- stress coupon for use in fatigue testing . This novel coupon design has a significantly greater surface area along the notch boundary...modified constant- stress coupon for use in fatigue testing . A constant- stress coupon is a novel design that has a significantly greater surface area along

  20. MobiDiC: Context Adaptive Digital Signage with Coupons

    Science.gov (United States)

    Müller, Jörg; Krüger, Antonio

    In this paper we present a field study of a digital signage system that measures audience response with coupons in order to enable context adaptivity. In the concept for context adaptivity, the signs sense their environment; decide which content to show, and then sense the audience reaction to the content shown. From this audience measurement, the strategies which content to show in which situation are refined. As one instantiation of audience measurement, we propose a novel simple couponing system, where customers can photograph the coupons at the signs. Thus, it can be measured whether customers really went to the shop. To investigate the feasibility of this approach, we implemented a prototype of 20 signs in the city center of Münster, Germany. During one year of deployment, we investigated usage of the system through interviews with shop owners and customers. Our experiences show that customer attention towards the signs is a major hurdle to overcome.

  1. Some new aspects of the coupon-collector's problem

    OpenAIRE

    Myers, Amy N.; Wilf, Herbert S.

    2003-01-01

    We extend the classical coupon collector's problem to one in which two collectors are simultaneously and independently seeking collections of $d$ coupons. We find, in finite terms, the probability that the two collectors finish at the same trial, and we find, using the methods of Gessel-Viennot, the probability that the game has the following ``ballot-like'' character: the two collectors are tied with each other for some initial number of steps, and after that the player who first gains the l...

  2. NFC mobile coupon protocols : developing, formal security modelling and analysis, and addressing relay attack.

    OpenAIRE

    Alshehri, Ali A.

    2015-01-01

    Near Field Communication} (NFC) is a Radio Frequency (RF) technology that allows data to be exchanged between devices that are in close proximity. An NFC-based mobile coupon (M-coupon) is a coupon that is retrieved by the user from a source such as a newspaper or a smart poster and redeemed afterwards. The NFC-based mobile coupon (M-coupon) is a cryptographically secured electronic message with some value stored at user's mobile. The M-coupon requires secure issuing and cashing (redeeming). ...

  3. Detection of Escherichia coli in biofilms from pipe samples and coupons in drinking water distribution networks.

    Science.gov (United States)

    Juhna, T; Birzniece, D; Larsson, S; Zulenkovs, D; Sharipo, A; Azevedo, N F; Ménard-Szczebara, F; Castagnet, S; Féliers, C; Keevil, C W

    2007-11-01

    Fluorescence in situ hybridization (FISH) was used for direct detection of Escherichia coli on pipe surfaces and coupons in drinking water distribution networks. Old cast iron main pipes were removed from water distribution networks in France, England, Portugal, and Latvia, and E. coli was analyzed in the biofilm. In addition, 44 flat coupons made of cast iron, polyvinyl chloride, or stainless steel were placed into and continuously exposed to water on 15 locations of 6 distribution networks in France and Latvia and examined after 1 to 6 months exposure to the drinking water. In order to increase the signal intensity, a peptide nucleic acid (PNA) 15-mer probe was used in the FISH screening for the presence or absence of E. coli on the surface of pipes and coupons, thus reducing occasional problems of autofluorescence and low fluorescence of the labeled bacteria. For comparison, cells were removed from the surfaces and examined with culture-based or enzymatic (detection of beta-d-glucuronidase) methods. An additional verification was made by using PCR. Culture method indicated presence of E. coli in one of five pipes, whereas all pipes were positive with the FISH methods. E. coli was detected in 56% of the coupons using PNA FISH, but no E. coli was detected using culture or enzymatic methods. PCR analyses confirmed the presence of E. coli in samples that were negative according to culture-based and enzymatic methods. The viability of E. coli cells in the samples was demonstrated by the cell elongation after resuscitation in low-nutrient medium supplemented with pipemidic acid, suggesting that the cells were present in an active but nonculturable state, unable to grow on agar media. E. coli contributed to ca. 0.001 to 0.1% of the total bacterial number in the samples. The presence and number of E. coli did not correlate with any of physical and/or chemical characteristic of the drinking water (e.g., temperature, chlorine, or biodegradable organic matter concentration

  4. On the mechanisms of the corrosion of weathering steel by SO{sub 2} in laboratory studies: influence of the environmental parameters

    Energy Technology Data Exchange (ETDEWEB)

    Marco, J. F., E-mail: jfmarco@iqfr.csic.es [Instituto de Química Física “Rocasolano”, CSIC (Spain)

    2017-11-15

    We report here on the mechanisms underlying the corrosion of weathering steel in accelerated laboratory tests using artificially polluted SO{sub 2}-atmospheres. The role of corrosion parameters such as the SO{sub 2} concentration, the exposure time, the relative humidity and temperature of the environment are discussed in detail. Through the extensive use of Mössbauer spectroscopy in both its transmission and electron detection modes, as well as with the help of other analysis techniques, the characterization of the different corrosion products at the various stages of the corrosion process has been carried out. The results complement the data obtained in field studies and help to understand the mechanisms involved in this complex phenomenon.

  5. 31 CFR 306.19 - Denominational exchanges of coupon securities.

    Science.gov (United States)

    2010-07-01

    ... 31 Money and Finance: Treasury 2 2010-07-01 2010-07-01 false Denominational exchanges of coupon securities. 306.19 Section 306.19 Money and Finance: Treasury Regulations Relating to Money and Finance (Continued) FISCAL SERVICE, DEPARTMENT OF THE TREASURY BUREAU OF THE PUBLIC DEBT GENERAL...

  6. 26 CFR 1.466-1 - Method of accounting for the redemption cost of qualified discount coupons.

    Science.gov (United States)

    2010-04-01

    ... the coupon. (2) Definitions—(i) Discount coupon. A discount coupon is a sales promotion device used to... than a reduction in the sales price of one of the issuer's products. The discount may be stated...

  7. Interest rates and coupon bonds in quantum finance

    CERN Document Server

    Baaquie, Belal E

    2009-01-01

    The economic crisis of 2008 has shown that the capital markets need new theoretical and mathematical concepts to describe and price financial instruments. Focusing almost exclusively on interest rates and coupon bonds, this book does not employ stochastic calculus - the bedrock of the present day mathematical finance - for any of the derivations. Instead, it analyzes interest rates and coupon bonds using quantum finance. The Heath-Jarrow-Morton and the Libor Market Model are generalized by realizing the forward and Libor interest rates as an imperfectly correlated quantum field. Theoretical models have been calibrated and tested using bond and interest rates market data. Building on the principles formulated in the author's previous book (Quantum Finance, Cambridge University Press, 2004) this ground-breaking book brings together a diverse collection of theoretical and mathematical interest rate models. It will interest physicists and mathematicians researching in finance, and professionals working in the fin...

  8. Consumers responses to coupons in direct-to-consumer advertising of prescription drugs.

    Science.gov (United States)

    Bhutada, Nilesh S; Cook, Christopher L; Perri, Matthew

    2009-01-01

    A study was conducted to understand the influence of coupons and consumers' level of involvement in direct-to-consumer advertising. Consumers exposed to prescription drug advertising with a coupon had significantly more favorable ad and brand-related attitudes, and intention to inquire about the drug to their doctor. However, there was no significant difference in perceived product risk between consumers exposed to the ad with a coupon and consumers exposed to the ad without a coupon. Highly involved consumers had significantly more favorable ad, brand, and coupon-related attitudes, drug inquiry intention, and perceptions about the risks associated with the drug.

  9. 31 CFR 306.18 - Exchanges of coupon securities for registered securities.

    Science.gov (United States)

    2010-07-01

    ... if presented when the transfer books are closed (in which case the exchange will be effected on or after the date on which the books are reopened), the next maturing coupons should be detached and held for collection in ordinary course when due. If any coupons which should be attached are missing,...

  10. The Valuation of Callable Bonds with Floored CMS-spread Coupons

    DEFF Research Database (Denmark)

    Skovmand, David; Jørgensen, Peter Løchte

    2007-01-01

    A new type of structured bond has recently been introduced with enormous success - primarily among private investors - in many countries in Europe. The bonds are medium term and with fixed and very high initial coupons. The remaining coupons are determined as a constant multiplier times the sprea...

  11. Development and test of flexible film coupon strips for use as a sampling technique

    Science.gov (United States)

    Aldridge, C.

    1969-01-01

    Film consisting of a gelatin base serves as a flexible, water soluble microbiological assay coupon for clean room use. It is nontoxic to microorganisms and capable of remaining unchanged during periods of storage.

  12. Receipt and use of half-fare airline coupons at selected Department of Energy field locations

    Energy Technology Data Exchange (ETDEWEB)

    1980-08-11

    The receipt and use of half-fare coupons obtained by employees of DOE field offices and DOE contractors while traveling at DOE expense were reviewed. These coupons, issued by United Airlines and American Airlines, provided for air travel at half-fare if used before December 15, 1979. Potential savings to DOE through coupon use ranging from $50,000 to $100,000 were lost, because of ineffective management action by both federal and contractor officials. Recommendations were that DOE ascertain the extent of the failure of contractors to recover coupons from their employees and recover from the contractors the amounts lost. IG submitted a draft of this final report for comment and received the comments of the Controller, the Director of Administration, and the Director of Procurement and Contracts Management. The comments included useful information; and where appropriate, the final report was changed to reflect the comments. In addition, the comments in their entirety are contained in the appendices.

  13. Development of Cu(In,Ga)Se2 Test Coupons for Potential Induced Degradation Studies

    Energy Technology Data Exchange (ETDEWEB)

    Contreras, Miguel A.; Hacke, Peter; Repins, Ingrid

    2016-11-21

    We report on the design, fabrication and accelerated testing of fully encapsulated small area coupons (approximately 7.5cm x 7.5 cm) for the purpose of researching potential induced degradation in Cu(In, Ga)Se2 based PV modules. The fabrication of these coupons enables the study of the solar cells and the materials used in PV module manufacturing such as top and bottom glass covers of different composition (soda-lime glass, high temperature glass, alkaline-free glass, etc), plastic-based top covers, ethylene vinyl acetate and edge seal encapsulation materials. The coupons can also be used to emulate framed and frameless modules that utilize either monolithically interconnected modules or singular cell type of modules. The design of the coupons, their fabrication, the materials used and their testing for 1000 hours under 85 degrees C and 85% RH conditions are presented.

  14. Thermal coupon testing of Load-Bearing Multilayer Insulation

    Science.gov (United States)

    Johnson, W. L.; Heckle, K. W.; Hurd, J.

    2014-01-01

    Advanced liquid hydrogen storage concepts being considered for long duration space travel incorporate refrigeration systems and cryocoolers to lower the heat load. Using a refrigeration loop to intercept the energy flowing through MLI to a liquid hydrogen tank at a temperature between the environment and the liquid hydrogen can lower the heat load on the propellant system by as much as 50%. However, the refrigeration loop requires structural integration into the MLI. Use of a more traditional concept of MLI underneath this refrigeration loop requires that a structural system be put in place to support the loop. Such structures, even when thermally optimized, present a relatively large parasitic heat load into the tank. Through NASA small business innovation research funding, Quest Thermal Group and Ball Aerospace have been developing a structural MLI based insulation system. These systems are designed with discrete polymeric spacers between reflective layers instead of either dacron or silk netting. The spacers (or posts) have an intrinsic structural capability that is beyond that of just supporting the internal insulation mechanical loads. This new MLI variant called Load Bearing MLI (LB-MLI) has been developed specifically for the application of supporting thermal shields within the insulation system. Test articles (coupons) of the new LB-MLI product were fabricated for thermal performance testing using liquid nitrogen at Kennedy Space Center (KSC) and using cryocooler based calorimetry at Florida State University. The test results and analysis are presented. Thermal models developed for correlation with the thermal testing results both at KSC and testing that was performed at Florida State University are also discussed.

  15. Control of microbiological corrosion on carbon steel with sodium hypochlorite and biopolymer.

    Science.gov (United States)

    Oliveira, Sara H; Lima, Maria Alice G A; França, Francisca P; Vieira, Magda R S; Silva, Pulkra; Urtiga Filho, Severino L

    2016-07-01

    In the present work, the interaction of a mixture of a biocide, sodium hypochlorite (NaClO), and a biopolymer, xanthan, with carbon steel coupons exposed to seawater in a turbulent flow regime was studied. The cell concentrations, corrosion rates, biomasses, and exopolysaccharides (EPSs) produced on the coupon surfaces with the various treatments were quantified. The corrosion products were evaluated using X-ray diffraction (XRD), and the surfaces of steels were analysed by scanning electron microscopy (SEM). The results indicated that xanthan and the hypochlorite-xanthan mixture reduced the corrosion rate of steel.

  16. Exposure to tobacco coupons among U.S. middle and high school students.

    Science.gov (United States)

    Tessman, Greta K; Caraballo, Ralph S; Corey, Catherine G; Xu, Xin; Chang, Cindy M

    2014-08-01

    Tobacco marketing contributes to increased tobacco use susceptibility and sustained use. There are limited data on youth exposure to tobacco coupons, a type of pro-tobacco promotion. To explore channels through which youth report exposure to coupons and characteristics associated with this exposure. This may help inform efforts aimed at decreasing youth exposure to advertising and promotion. Data from the 2012 National Youth Tobacco Survey were analyzed in 2013 to estimate the self-reported prevalence of U.S. middle and high school student exposure to coupons through various channels. Associations among exposure to coupons and demographics, tobacco use, living with a tobacco user, and receptivity to tobacco marketing were examined using multivariate logistic regression models. Approximately 13% of students reported exposure to tobacco coupons in the past 30 days through mail, digital communications, or tobacco packages. Prevalence was greatest among current tobacco users (34.0%) and those receptive to tobacco marketing (23.4%) compared to non-tobacco users (9.3%) and those not receptive to tobacco marketing (8.2%), respectively. Coupon exposure varied by sex, grade, and race/ethnicity. In adjusted models, current tobacco use (AOR=3.4, 95% CI=3.0, 3.9); living with a tobacco user (AOR=2.1, 95% CI=1.9, 2.4); and receptivity to tobacco marketing (AOR=2.3, 95% CI=2.0, 2.7) were independently associated with coupon exposure. Findings from this study indicate that despite restrictions on marketing to youth, youth are still being exposed to tobacco promotions such as coupons. Efforts to limit youth exposure may be valuable in reducing curiosity, susceptibility, and initiation. Published by Elsevier Inc.

  17. The emergence of Smartphones: An exploratory study of consumer attitude and intention to redeem mobile coupons

    OpenAIRE

    Lao, Ka Man

    2012-01-01

    Purpose - The prevalence of mobile phones, especially the development of smartphones, has attracted numerous companies to exploit the potential in mobile marketing. One notable mobile marketing tool that is progressively gaining interest is the mobile coupon. The aim of this study is to build a conceptual model to explain consumers’ attitude and intention to redeem mobile coupon in the emergence of smartphones. Design/methodology/approach – This study is based on an online survey questionn...

  18. 一种建筑用高性能耐火耐候钢的焊接试验%Welding Test for High Performance Fire and Weathering Resistant Steel Used for Building

    Institute of Scientific and Technical Information of China (English)

    李世红; 田璐; 牛全峰

    2011-01-01

    针对具有优异强韧性及耐火耐候性能的建筑用WGJ510C2钢,进行了气体保护焊焊接评定试验研究,内容包括熔敷金属试验、接头常规力学性能试验、高温拉伸性能试验及微观组织分析.结果表明,焊接接头常温和高温拉伸强度均满足WGJ510C2钢技术条件要求,焊接接头低温冲击功有较大的富余量.因此,采用气体保护焊焊接方法及NHG-1焊丝匹配WGJ510C2钢,焊接接头综合性能指标完全满足高层建筑用钢焊接技术要求.%The welding assessment test research of gas shielded was conducted, for WGJ510C2 steel with high toughness, fire and weathering resistant used for building. The tests included deposited metal test, routine mechanical properties test of welded joint, tensile performance test at high temperature and microstructure analysis. The results showed that the tensile property at room temperature and high temperature both can meet the welding requirements of WGJ510C2 steel, and the impact energy value of welded joint is surplus at low temperature . Therefore, adopting gas shielded welding method and NHG-1 wire to match with WGJ510C2 steel, the comprehensive properties of welded joint can completely satisfy the welding requirements of the steel used for high-rise building.

  19. Microbial corrosion of carbon steel by sulfate-reducing bacteria:

    DEFF Research Database (Denmark)

    Nielsen, Lars Vendelbo; Hilbert, Lisbeth Rischel

    1997-01-01

    Electrochemical measurements (EIS and DC-polarisation curves) have been conducted on carbon steel coupons exposed in SRB-active environments. Results from EIS measurements show that very large interfacial capacities are found in such systems, and consequently high capacitive currents are to be ex...

  20. Microbial corrosion of carbon steel by sulfate-reducing bacteria:

    DEFF Research Database (Denmark)

    Nielsen, Lars Vendelbo; Hilbert, Lisbeth Rischel

    1997-01-01

    Electrochemical measurements (EIS and DC-polarisation curves) have been conducted on carbon steel coupons exposed in SRB-active environments. Results from EIS measurements show that very large interfacial capacities are found in such systems, and consequently high capacitive currents...... for a misleading conclusion that increasing corrosion rates are caused by cathodic depolarisation in SRB-active environments....

  1. Determination of zero-coupon and spot rates from treasury data by maximum entropy methods

    Science.gov (United States)

    Gzyl, Henryk; Mayoral, Silvia

    2016-08-01

    An interesting and important inverse problem in finance consists of the determination of spot rates or prices of the zero coupon bonds, when the only information available consists of the prices of a few coupon bonds. A variety of methods have been proposed to deal with this problem. Here we present variants of a non-parametric method to treat with such problems, which neither imposes an analytic form on the rates or bond prices, nor imposes a model for the (random) evolution of the yields. The procedure consists of transforming the problem of the determination of the prices of the zero coupon bonds into a linear inverse problem with convex constraints, and then applying the method of maximum entropy in the mean. This method is flexible enough to provide a possible solution to a mispricing problem.

  2. Random Amplitude Fatigue Life of Electroformed Nickel Micro-Channel Heat Exchanger Coupons

    Directory of Open Access Journals (Sweden)

    Larry Byrd

    1998-01-01

    Full Text Available The use of micro-channel heat exchangers (MCHEX with coolant flow passage diameters less than 1 mm has been proposed for heat flux, weight, or volume limited environments. This paper presents room temperature, random amplitude, ε − N (strain versus number of cycles to failure curves for MCHEX coupons formed by electroplating nickel on a suitable form. These coupons are unique in two aspects; the microstructure formed by electroplating and the presence of holes as an integral part of the structure. The hole diameters range from approximately 10% to 50% to the specimen thickness. The fatigue life of electroformed nickel can be estimated from constant amplitude data using the formulation presented. The heat exchangers with channels parallel to the coupon direction have a lower fatigue life than the solid material.

  3. Identification of Factors of Influence upon the Cost of Fixed Coupon Securities

    Directory of Open Access Journals (Sweden)

    Hlotov Yevhen O.

    2014-01-01

    Full Text Available The article studies fixed coupon securities (bonds. It provides a calculation of the cash flow, generated by fixed coupon securities, with enclosed discounted face value of securities. It analyses time indicator – average weighted duration of payments, which characterises sensitivity of the price of securities to changes of interest rates in the market. It proves availability of two groups of interconnections between the cost of a bond, coupon rate, market rate (rate of return and term of its payment. The first group of interconnections reflects interconnections between the cost of a bond, coupon rate and market rate (rate of return. The second group characterises connection between the bond cost and term of its payment. The authors study the average weighted duration of payments. It plays an important role in analysis of long-term securities with fixed income. To simplify calculations it was accepted that the coupon payment is done once a year. The article offers a formula for identifying inaccuracy of the bond price depending on the expected change of profitability on payment. Analysing duration properties the article identifies shortcomings inherent in this indicator. Taking into account the average weighted duration of payments the article recommends a formula, as more efficient, for identification of the future bond price depending on change of profitability. The conducted studies are a theoretical ground for development of models of management of fixed income securities portfolios. The obtained scientific results could be used in the educational process both in colleges and specialised trainings of securities specialists. The scientific results could be used for developing information technologies when identifying cost of securities (fixed coupon bonds.

  4. Estimating Multivariate Exponentail-Affine Term Structure Models from Coupon Bound Prices using Nonlinear Filtering

    DEFF Research Database (Denmark)

    Baadsgaard, Mikkel; Nielsen, Jan Nygaard; Madsen, Henrik

    2000-01-01

    An econometric analysis of continuous-timemodels of the term structure of interest rates is presented. A panel of coupon bond prices with different maturities is used to estimate the embedded parameters of a continuous-discrete state space model of unobserved state variables: the spot interest rate......, the central tendency and stochastic volatility. Emphasis is placed on the particular class of exponential-affine term structure models that permits solving the bond pricing PDE in terms of a system of ODEs. It is assumed that coupon bond prices are contaminated by additive white noise, where the stochastic...

  5. Marine corrosion of mild steel at Lumut, Perak

    Science.gov (United States)

    Ting, Ong Shiou; Potty, Narayanan Sambu; Liew, Mohd. Shahir

    2012-09-01

    The corrosion rate of structural steels in the adverse marine and offshore environments affects the economic interest of offshore structures since the loss of steel may have significant impact on structural safety and performance. With more emphasis to maintain existing structures in service for longer time and hence to defer replacement costs, there is increasing interest in predicting corrosion rate at a given location for a given period of exposure once the protection coating or cathodic protection is lost. The immersion depth, salinity, steel composition and water pollution will be taken into account. Various corrosion allowances are prescribed for structural members by different standards. There are no studies to determine the appropriate corrosion allowance for steel structures in marine environment in Malaysia. The objectives of the research are to determine the nature and rate of corrosion in mm/year for steel structures in marine environment. It also tries to identify whether the corrosion rate is affected by differences in the chemical composition of the steels, and microalgae. Two sets of corrosion coupons of Type 3 Steel consisting of mild steel were fabricated and immersed in seawater using steel frames. The corrosion rate of the coupon in mm/ per year is estimated based on the material weight loss with time in service. The results are compared with recommendations of the code.

  6. Characterisation of recycled mixed plastic solid wastes: Coupon and full-scale investigation.

    Science.gov (United States)

    Bajracharya, Rohan Muni; Manalo, Allan C; Karunasena, Warna; Lau, Kin-Tak

    2016-02-01

    In Australia, the plastic solid waste (PSW) comprises 16% by weight of municipal solid waste but only about one-fourth are recycled. One of the best options to increase the recycling rate of mixed PSW is to convert them into products suitable for construction. However, a comprehensive understanding on the mechanical behaviour of mixed PSW under different loading conditions is important for their widespread use as a construction material. This study focuses on investigating the mechanical behaviour of recycled mixed PSW containing HDPE, LDPE and PP using coupon and full-scale specimens. From coupon test, the strength values were found to be 14.8, 19.8, 20, 5.6MPa in tension, compression, flexure and shear respectively, while the modulus of elasticity are 0.91, 1.03, 0.72GPa in tension, compression and flexure respectively. The coefficient of variance of the measured properties for coupon and fullscale specimens was less than 10% indicating that consistent material properties can be obtained for mixed PSW. More importantly, the strength properties of mixed PSW are comparable to softwood structural timber. The flexural behaviour of full-scale specimens was also predicted using fibre model analysis and finite element modelling. Comparison showed that using coupon specimen's properties, the flexural behaviour of the full-scale specimens can be predicted reliably which can eliminate the costly and time consuming arrangements for full-scale experimental tests.

  7. High Current ESD Test of Advanced Triple Junction Solar Array Coupon

    Science.gov (United States)

    Wright, Kenneth H., Jr.; Schneider, Todd A.; Vaughn, Jason A.; Hoang, Bao; Wong, Frankie

    2014-01-01

    Testing was conducted on an Advanced Triple Junction (ATJ) coupon that was part of a risk reduction effort in the development of a high-powered solar array design by Space Systems Loral, LLC (SSL). The ATJ coupon was a small, 4-cell, two-string configuration of flight-type design that has served as the basic test coupon design used in previous SSL environmental aging campaigns. The objective of the present test was to evaluate the performance of the coupon after being subjected to induced electrostatic discharge (ESD) testing at two string voltages (100 V, 150 V) and four string currents (1.65 A, 2.0 A, 2.475 A, and 3.3 A). An ESD test circuit, unique to SSL solar array design, was built that simulates the effect of missing cells and strings in a full solar panel with special primary arc flashover circuitry. A total of 73 primary arcs were obtained that included 7 temporary sustained arcs (TSA) events. The durations of the TSAs ranged from 50 micro-seconds to 2.75 milli-seconds. All TSAs occurred at a string voltage of 150 V. Post-ESD functional testing showed that no degradation occurred due to the TSA events. These test results point to a robust design for application to a high-current, high-power mission.

  8. 31 CFR 306.17 - Exchanges of registered securities for coupon securities.

    Science.gov (United States)

    2010-07-01

    ... 31 Money and Finance: Treasury 2 2010-07-01 2010-07-01 false Exchanges of registered securities for coupon securities. 306.17 Section 306.17 Money and Finance: Treasury Regulations Relating to Money and Finance (Continued) FISCAL SERVICE, DEPARTMENT OF THE TREASURY BUREAU OF THE PUBLIC DEBT...

  9. Antibacterial effect of silver nanofilm modified stainless steel surface

    Science.gov (United States)

    Fang, F.; Kennedy, J.; Dhillon, M.; Flint, S.

    2015-03-01

    Bacteria can attach to stainless steel surfaces, resulting in the colonization of the surface known as biofilms. The release of bacteria from biofilms can cause contamination of food such as dairy products in manufacturing plants. This study aimed to modify stainless steel surfaces with silver nanofilms and to examine the antibacterial effectiveness of the modified surface. Ion implantation was applied to produce silver nanofilms on stainless steel surfaces. 35 keV Ag ions were implanted with various fluences of 1 × 1015 to 1 × 1017 ions•cm-2 at room temperature. Representative atomic force microscopy characterizations of the modified stainless steel are presented. Rutherford backscattering spectrometry spectra revealed the implanted atoms were located in the near-surface region. Both unmodified and modified stainless steel coupons were then exposed to two types of bacteria, Pseudomonas fluorescens and Streptococcus thermophilus, to determine the effect of the surface modification on bacterial attachment and biofilm development. The silver modified coupon surface fluoresced red over most of the surface area implying that most bacteria on coupon surface were dead. This study indicates that the silver nanofilm fabricated by the ion implantation method is a promising way of reducing the attachment of bacteria and delay biofilm formation.

  10. High Current ESD Test of Advanced Triple Junction Solar Array Coupon

    Science.gov (United States)

    Wright, Kenneth H., Jr.; Schneider, Todd A.; Vaughn, Jason A.; Hoang, Bao; Wong, Frankie

    2015-01-01

    A test was conducted on an Advanced Triple Junction (ATJ) coupon that was part of a risk reduction effort in the development of a high-powered solar array design by SSL. The ATJ coupon was a small, 4-cell, two-string configuration that has served as the basic test coupon design used in previous SSL environmental aging campaigns. The coupon has many attributes of the flight design; e.g., substrate structure with graphite face sheets, integrated by-pass diodes, cell interconnects, RTV grout, wire routing, etc. The objective of the present test was to evaluate the performance of the coupon after being subjected to induced electrostatic discharge testing at two string voltages (100 V, 150 V) and four array current (1.65 A, 2.0 A, 2.475 A, and 3.3 A). An ESD test circuit, unique to SSL solar array design, was built that simulates the effect of missing cells and strings in a full solar panel with special primary arc flashover circuitry. A total of 73 primary arcs were obtained that included 7 temporary sustained arcs (TSA) events. The durations of the TSAs ranged from 50 micros to 2.9 ms. All TSAs occurred at a string voltage of 150 V. Post-test Large Area Pulsed Solar Simulator (LAPSS), Dark I-V, and By-Pass Diode tests showed that no degradation occurred due to the TSA events. In addition, the post-test insulation resistance measured was > 50 G-ohms between cells and substrate. These test results indicate a robust design for application to a high-current, high-power mission application.

  11. Rhenium Uptake, as Analogue for Tc-99, by Steel Corrosion Products

    Energy Technology Data Exchange (ETDEWEB)

    Krupka, Kenneth M.; Brown, Christopher F.; Schaef, Herbert T.; Heald, Steve M.; Valenta, Michelle M.; Arey, Bruce W.

    2006-04-30

    Static batch experiments were used to examine the sorption of dissolved perrhenate [Re(VII)], as a surrogate for pertechnetate [Tc(VII)], on corrosion products of A-516 carbon steel coupons contacted with synthetic groundwater or dilute water. After 109 days of contact time, the concentration of dissolved Re(VII) in the synthetic groundwater matrix decreased by approximately 26%; the dilute water matrix experienced a 99% decrease in dissolved Re(VII) over the same time period. Bulk XRD results for the corroded steel coupons showed that the corrosion products consisted primarily of maghemite, lepidocrocite, and goethite. Analyses of the coupons by SEM/EDS indicated that Re was present with the morphologically complex assemblages of Fe oxide/hydroxide corrosion products for samples spiked with the highest dissolved Re(VII) concentration (1.0 mmol/L) used for these experiments. Analyses of corroded steel coupons contacted with solutions containing 1.0 mmol/L Re(VII) by synchrotron-based methods confirmed the presence of Re sorbed with the corrosion product on the steel coupons. Analyses showed that the Re sorbed on these corroded coupons was in the +7 oxidation state, suggesting that the Re(VII) uptake mechanism did not involve reduction of Re to a lower oxidation state, such as +4. The results of our studies using Re(VII) as an analogue for Tc(VII)-99 suggest that Tc(VII)-99 would also be sorbed with steel corrosion products and that the inventory of Tc(VII)-99 released from breached waste packages would be lower than what is now conservatively estimated.

  12. Wacky Weather

    Science.gov (United States)

    Sabarre, Amy; Gulino, Jacqueline

    2013-01-01

    What do a leaf blower, water hose, fan, and ice cubes have in common? Ask the students who participated in an integrative science, technology, engineering, and mathematics (I-STEM) education unit, "Wacky Weather," and they will tell say "fun and severe weather"--words one might not have expected! The purpose of the unit…

  13. Wacky Weather

    Science.gov (United States)

    Sabarre, Amy; Gulino, Jacqueline

    2013-01-01

    What do a leaf blower, water hose, fan, and ice cubes have in common? Ask the students who participated in an integrative science, technology, engineering, and mathematics (I-STEM) education unit, "Wacky Weather," and they will tell say "fun and severe weather"--words one might not have expected! The purpose of the unit…

  14. Mirador - Weather

    Data.gov (United States)

    National Aeronautics and Space Administration — Earth Science data access made simple. Our weather system includes the dynamics of the atmosphere and its interaction with the oceans and land. The improvement of...

  15. Progress of Study on Application of Rare Earth Metals in Steels

    Institute of Scientific and Technical Information of China (English)

    Wang Longmei; Lin Qin; Ji Jingwen; Lan Denian

    2004-01-01

    With the improvement of the clean steel by degrees, the functions of rare earth metals in steel are more focused on modification of inclusions and micro alloying.The new study concerning the application of RE metals in clean steels were investigated by ICP, metallographic examination, SEM, EDS, EPMA, TEM and IMMA.The mechanism of corrosion resistance in the weather resistance steel was clarified.The mechanism of abrasion resistance and the life of fatigue enhanced in the RE - heavy rails steel were discussed.Progress in study of application of rare earth metals in steels (including weather resistance steel, low alloy steel, and heavy rails steel) was covered in this paper.

  16. Bypass Diode Temperature Tests of a Solar Array Coupon Under Space Thermal Environment Conditions

    Science.gov (United States)

    Wright, Kenneth H., Jr.; Schneider, Todd A.; Vaughn, Jason A.; Hoang, Bao; Wong, Frankie; Wu, Gordon

    2016-01-01

    Tests were performed on a 56-cell Advanced Triple Junction solar array coupon whose purpose was to determine margin available for bypass diodes integrated with new, large multi-junction solar cells that are manufactured from a 4-inch wafer. The tests were performed under high vacuum with coupon back side thermal conditions of both cold and ambient. The bypass diodes were subjected to a sequence of increasing discrete current steps from 0 Amp to 2.0 Amp in steps of 0.25 Amp. At each current step, a temperature measurement was obtained via remote viewing by an infrared camera. This paper discusses the experimental methodology, experiment results, and the thermal model.

  17. The Role of Hispanic Acculturation on Media Exposure, Coupon Use, and Brand Loyalty

    OpenAIRE

    Petroshius, Susan M; Stephen J. Newell; Ross, Steven J

    1995-01-01

    The Hispanic population in the United States is rapidly increasing and is expected to be the largest minority group within the next decade. Consequently, a better understanding of this group of consumers is of great importance to marketers. This study investigates the role that acculturation plays on a number of consumer-related attitudes and behaviors. The results indicate that as acculturation increases, Hispanic consumers are more frequently exposed to English language media, use coupons w...

  18. Age Induced Effects on ESD Characteristics of Solar Array Coupons After Combined Space Environmental Exposures

    Science.gov (United States)

    Wright, Kenneth H.; Schneider, Todd A.; Vaughn, Jason A.; Hoang, Bao; Funderburk, Victor V.; Wong, Frankie; Gardiner, George

    2012-01-01

    A set of multi-junction GaAs/Ge solar array test coupons provided by Space Systems/Loral were subjected to a sequence of 5-year increments of combined space environment exposure tests. The test coupons capture an integrated design intended for use in a geosynchronous (GEO) space environment. A key component of this test campaign is performing electrostatic discharge (ESD) tests in the inverted gradient mode. The protocol of the ESD tests is based on the ISO standard for ESD testing on solar array panels [ISO-11221]. The test schematic in the ISO reference has been modified with Space System/Loral designed circuitry to better simulate the on-orbit operational conditions of its solar array design. Part of the modified circuitry is to simulate a solar array panel coverglass flashover discharge. All solar array coupons used in the test campaign consist of four cells constructed to form two strings. The ESD tests were performed at the beginning-of-life (BOL) and at each 5-year environment exposure point until end-of-life (EOL) at 15 years. The space environmental exposure sequence consisted of ultra-violet radiation, electron/proton particle radiation, thermal cycling, and Xenon ion thruster plume erosion. This paper describes the ESD test setup and the importance of the electrical test design in simulating the on-orbit operational conditions. Arc inception voltage results along with ESD test behavior from the BOL condition through the 15th year age condition are discussed. In addition, results from a Xenon plasma plume exposure test with an EOL coupon under the full ESD test condition will be discussed.

  19. Queued History based Mediator Identification for an Incentive Attached peer to peer Electronic Coupon System

    Science.gov (United States)

    Shojima, Taiki; Ikkai, Yoshitomo; Komoda, Norihisa

    An incentive attached peer to peer (P2P) electronic coupon system is proposed in which users forward e-coupons to potential users by providing incentives to those mediators. A service provider needs to acquire distribution history for incentive payment by recording UserIDs (UIDs) in the e-coupons, since this system is intended for pure P2P environment. This causes problems of dishonestly altering distribution history. In order to solve such problems, distribution history is realized in a couple of queues structure. They are the UID queue, and the public key queue. Each element of the UID queue at the initial state consists of index, a secret key, and a digital signature. In recording one's UID, the encrypted UID is enqueued to the UID queue with a new digital signature created by a secret key of the dequeued element, so that each UID cannot be altered. The public key queue provides the functionality of validating digital signatures on mobile devices. This method makes it possible both each UID and sequence of them to be certificated. The availability of the method is evaluated by quantifying risk reduction using Fault Tree Analysis (FTA). And it's recognized that the method is better than common encryption methods.

  20. Electrostatic Discharge Test of Multi-Junction Solar Array Coupons After Combined Space Environmental Exposures

    Science.gov (United States)

    Wright, Kenneth H.; Schneider, Todd; Vaughn, Jason; Hoang, Bao; Funderburk, Victor V.; Wong, Frankie; Gardiner, George

    2010-01-01

    A set of multi-junction GaAs/Ge solar array test coupons were subjected to a sequence of 5-year increments of combined environmental exposure tests. The test coupons capture an integrated design intended for use in a geosynchronous (GEO) space environment. A key component of this test campaign is conducting electrostatic discharge (ESD) tests in the inverted gradient mode. The protocol of the ESD tests is based on the ISO/CD 11221, the ISO standard for ESD testing on solar array panels. This standard is currently in its final review with expected approval in 2010. The test schematic in the ISO reference has been modified with Space System/Loral designed circuitry to better simulate the on-orbit operational conditions of its solar array design. Part of the modified circuitry is to simulate a solar array panel coverglass flashover discharge. All solar array coupons used in the test campaign consist of 4 cells. The ESD tests are performed at the beginning of life (BOL) and at each 5-year environment exposure point. The environmental exposure sequence consists of UV radiation, electron/proton particle radiation, thermal cycling, and ion thruster plume. This paper discusses the coverglass flashover simulation, ESD test setup, and the importance of the electrical test design in simulating the on-orbit operational conditions. Results from 5th-year testing are compared to the baseline ESD characteristics determined at the BOL condition.

  1. Laser Cut Nitinol Tubing Fatigue Coupon: Design, Testing, and Endurance Limit

    Science.gov (United States)

    Forcucci, Stephen J.

    2014-07-01

    Nitinol medical device implants made from a laser cut tubing process (i.e., stents, valve structures, etc.) frequently require a fatigue durability assessment, which necessitates determining the material fatigue properties. Towards the goal of determining the strain-based endurance limit of medical grade superelastic Nitinol tubing, a coupon was designed and evaluated via FEA using Abaqus software, produced via laser cutting, shape setting, and electro-polishing processes, and then fatigue tested to 10 million cycles. FEA was used to determine the strain versus alternating displacement amplitude for the coupon. Error due to dimensional tolerances was determined. The coupons were then fatigue tested in a 37 °C temperature deionized water bath at alternating strain levels ranging from 0.75 to 4.0% at zero mean strain. Sample replication was greater than 90%, and the median alternating strain fatigue limit was determined via two methods. Confidence and reliability with maximum likelihood statistics are used to present a strain-based endurance limit for the material. The results seem to differ from previous published values.

  2. Portable hyperspectral fluorescence imaging system for detection of biofilms on stainless steel surfaces

    Science.gov (United States)

    Jun, Won; Lee, Kangjin; Millner, Patricia; Sharma, Manan; Chao, Kuanglin; Kim, Moon S.

    2008-04-01

    A rapid nondestructive technology is needed to detect bacterial contamination on the surfaces of food processing equipment to reduce public health risks. A portable hyperspectral fluorescence imaging system was used to evaluate potential detection of microbial biofilm on stainless steel typically used in the manufacture of food processing equipment. Stainless steel coupons were immersed in bacterium cultures, such as E. coli, Pseudomonas pertucinogena, Erwinia chrysanthemi, and Listeria innocula. Following a 1-week exposure, biofilm formations were assessed using fluorescence imaging. In addition, the effects on biofilm formation from both tryptic soy broth (TSB) and M9 medium with casamino acids (M9C) were examined. TSB grown cells enhance biofilm production compared with M9C-grown cells. Hyperspectral fluorescence images of the biofilm samples, in response to ultraviolet-A (320 to 400 nm) excitation, were acquired from approximately 416 to 700 nm. Visual evaluation of individual images at emission peak wavelengths in the blue revealed the most contrast between biofilms and stainless steel coupons. Two-band ratios compared with the single-band images increased the contrast between the biofilm forming area and stainless steel coupon surfaces. The 444/588 nm ratio images exhibited the greatest contrast between the biofilm formations and stainless coupon surfaces.

  3. Feynman perturbation expansion for the price of coupon bond options and swaptions in quantum finance. I. Theory.

    Science.gov (United States)

    Baaquie, Belal E

    2007-01-01

    European options on coupon bonds are studied in a quantum field theory model of forward interest rates. Swaptions are briefly reviewed. An approximation scheme for the coupon bond option price is developed based on the fact that the volatility of the forward interest rates is a small quantity. The field theory for the forward interest rates is Gaussian, but when the payoff function for the coupon bond option is included it makes the field theory nonlocal and nonlinear. A perturbation expansion using Feynman diagrams gives a closed form approximation for the price of coupon bond option. A special case of the approximate bond option is shown to yield the industry standard one-factor HJM formula with exponential volatility.

  4. Biofilm Formation and Adaptation by Pseudomonas fluorescens on both Biotite and Glass Coupons Under Varying Fe-Nutrient Availability

    Science.gov (United States)

    Grant, M.; Helms, G. L.; Shi, Z.; Thomashow, L.; Keller, C. K.; Harsh, J. B.

    2014-12-01

    We isolated an efficient weathering strain of Pseudomonas fluorescens from the rhizosphere of a White Pine (Pinus strobus) seedling. We grew it in a drip-flow biofilm reactor using both Fe-abundant and Fe-deficient media on either a glass or biotite coupon. Our working hypothesis was that the bacterium would respond to Fe deficiency by enhancing biotite weathering through an increase in the relative amount of polysaccharides in the biofilm compared to the Fe-abundant treatment. Because Fe is necessary for biofilm development, we hypothesized that biomass production on the biotite surface would exceed that on a Fe-free glass slide only in the Fe-deficient medium. We quantified total biomass, specific number of viable cells (SNVC), and the concentrations of K, Mg, and Fe in the biofilm. High-resolution magic angle spinning proton nuclear magnetic resonance (HR-MAS 1H-NMR) spectroscopy was used to characterize the biofilm matrix in terms of relative biofilm constituent concentrations. Compared with biofilms grown on glass, biofilms grown on biotite had higher total biomass and SNVC irrespective of Fe supply, with a near doubling of both the biofilm biomass from 0.43 to 0.76 mg cm-2 and SNVC from 1.52 × 107 to 3.24 × 107 CFU cm-2 mg-1 when Fe was deficient, and an increase in biomass from 1.94 to 2.46 mg cm-2 and in SNVC from 8.39 × 107 to 1.96 × 108 CFU cm-2 mg-1 when Fe was sufficient. Similarly with Fe deficient, the cation concentrations in biofilms grown on biotite vs. glass increased 2.14 and 2.46 times for K and Mg, respectively, and 7.01 times for Fe. When Fe was sufficient, the concentrations of cations increased 1.24, 2.07, and 3.77 times for K, Mg, and Fe, respectively. Based on NMR spectra, no significant change in biofilm chemistry occurred between the glass and biotite systems whether Fe was deficient or not. However, we did observe an increase in the ratio of the integrated areas corresponding to the carbohydrate and protein NMR regions, increasing

  5. Efficiency of inhibitor for biocorrosion influenced by consortium sulfate reducing bacteria on carbon steel

    Science.gov (United States)

    Mahat, Nur Akma; Othman, Norinsan Kamil; Sahrani, Fathul Karim

    2015-09-01

    The inhibition efficiency of benzalkonium chloride (BKC) in controlling biocorrosion on the carbon steel surfaces has been investigated. The carbon steel coupons were incubated in the presence of consortium SRB (C-SRB) with and without BKC for the difference medium concentration. The corrosion rate and inhibition efficiency have been evaluated by a weight loss method. The morphology of biofilm C-SRB on the steel surfaces were characterized with variable pressure scanning electron microscopy (VPSEM). The results revealed that BKC exhibits a low corrosion rate, minimizing the cell growth and biofilm development on the carbon steel surfaces.

  6. Efficiency of inhibitor for biocorrosion influenced by consortium sulfate reducing bacteria on carbon steel

    Energy Technology Data Exchange (ETDEWEB)

    Mahat, Nur Akma; Othman, Norinsan Kamil [School of Applied Physics, Faculty of Science and Technology, Universiti Kebangsaan Malaysia, 43600 Bangi, Selangor (Malaysia); Sahrani, Fathul Karim [School of Environment and Natural Resources Science, Faculty of Science and Technology, Universiti Kebangsaan Malaysia, 43600 Bangi, Selangor (Malaysia)

    2015-09-25

    The inhibition efficiency of benzalkonium chloride (BKC) in controlling biocorrosion on the carbon steel surfaces has been investigated. The carbon steel coupons were incubated in the presence of consortium SRB (C-SRB) with and without BKC for the difference medium concentration. The corrosion rate and inhibition efficiency have been evaluated by a weight loss method. The morphology of biofilm C-SRB on the steel surfaces were characterized with variable pressure scanning electron microscopy (VPSEM). The results revealed that BKC exhibits a low corrosion rate, minimizing the cell growth and biofilm development on the carbon steel surfaces.

  7. 高强度耐候H型钢和普通C-Mn低合金H型钢耐大气腐蚀性能比较%Comparison of Atmospheric Corrosion Resistance between High Strength Weathering H Section Steel and Common C-Mn Steel

    Institute of Scientific and Technical Information of China (English)

    米丰毅; 王向东; 陈小平; 彭云; 陶东平

    2011-01-01

    通过周浸加速腐蚀试验,对比了高强度耐候H型钢与普通C-Mn低合金H型钢的耐蚀性能,采用扫描电镜(SEM)、X射线衍射(XRD)及电化学阻抗谱(EIS)等方法研究了两种钢腐蚀产物的形貌、组成以及电化学性质的差异.结果表明,在模拟工业大气环境下,高强耐候H型钢的耐蚀性显著优于普通C-Mn钢,腐蚀产物性质的差别是导致两种钢腐蚀率差异的主要原因.普通C-Mn钢腐蚀后表面粗糙,锈层疏松且存在大量贯穿性裂纹;耐候H型钢锈层连续致密,且腐蚀产物主要由保护性较好的α-FeOOH和非晶态锈组成,能有效减缓电化学腐蚀反应的进行.%The differences of corrosion resistance between high strength weathering H section steel (HSWS-H) and common C-Mn steel (CMS) were investigated by cyclic immersion corrosion test, scanning electron microscopy (SEM), X-ray diffraction (XRD) and electrochemical impedance spectroscopy (ELS). The results showed that HSWS-H exhibited much higher corrosion resistance than CMS in the simulated industrial atmospheric environment.The difference between two corrosion products of the experimental steels was the main cause of the corrosion rate difference. The corrosion surface of CMS was rough, the rust layer was loose and had lots of perfoliate crack The rust layer of HSWS-H was continuous, dense and mainly consisted of α-FeOOH and amorphous phase, which can inhibit the electrochemical corrosion reaction effectively.

  8. Interaction of uranium with in situ anoxically generated magnetite on steel

    Energy Technology Data Exchange (ETDEWEB)

    Rovira, Miquel [Departament d' Enginyeria Quimica, Universitat Politecnica de Catalunya (UPC), Av. Diagonal 647, 08028 Barcelona (Spain); CTM Centre Tecnologic, Avda. Bases de Manresa 1, 08240 Manresa (Spain); El Aamrani, Souad [Departament d' Enginyeria Quimica, Universitat Politecnica de Catalunya (UPC), Av. Diagonal 647, 08028 Barcelona (Spain); Duro, Lara [ENVIROS-SPAIN S.L., Passeig de Rubi 29-31, 08197 Valldoreix (Spain); Gimenez, Javier [Departament d' Enginyeria Quimica, Universitat Politecnica de Catalunya (UPC), Av. Diagonal 647, 08028 Barcelona (Spain)]. E-mail: francisco.javier.gimenez@upc.edu; Pablo, Joan de [Departament d' Enginyeria Quimica, Universitat Politecnica de Catalunya (UPC), Av. Diagonal 647, 08028 Barcelona (Spain); CTM Centre Tecnologic, Avda. Bases de Manresa 1, 08240 Manresa (Spain); Bruno, Jordi [ENVIROS-SPAIN S.L., Passeig de Rubi 29-31, 08197 Valldoreix (Spain)

    2007-08-25

    In the high level nuclear waste repository concept, spent nuclear fuel is designed to be encapsulated in steel canisters. Thus, it is necessary to study the influence of the steel and/or its corrosion products on the behaviour of the radionuclides released from the fuel. In this sense, the main objective of this work is to contribute to the knowledge of the influence of the steel and/or its corrosion products on the uranium(VI) retention. To this aim, magnetite (Fe{sub 3}O{sub 4}) has been generated by anaerobic steel corrosion in an autoclave reactor at an overpressure of 8 atm of H{sub 2}(g). After characterisation by X-ray diffraction (XRD), the obtained corroded steel coupons were contacted, at two different H{sub 2}(g) pressures (1 atm and 7.6 atm), with a U(VI) solution. The evolution of the uranium concentration in solution is determined and a study of the composition of the coupons at the end of the experiments is carried out. The main conclusion obtained from this work is that magnetite generated on a steel coupon is able not only to retain uranium via sorption, but also to reduce hexavalent to tetravalent uranium in a higher extent than commercial magnetite, thus, providing an effective retardation path to the migration of uranium (and, potentially, other actinides) out of the repository.

  9. Characterization of corrosion scale formed on stainless steel delivery pipe for reclaimed water treatment.

    Science.gov (United States)

    Cui, Yong; Liu, Shuming; Smith, Kate; Yu, Kanghua; Hu, Hongying; Jiang, Wei; Li, Yuhong

    2016-01-01

    To reveal corrosion behavior of stainless steel delivery pipe used in reclaimed water treatment, this research focused on the morphological, mineralogical and chemical characteristics of stainless steel corrosion scale and corroded passive film. Corrosion scale and coupon samples were taken from a type 304 pipe delivering reclaimed water to a clear well in service for more than 12 years. Stainless steel corrosion scales and four representative pipe coupons were investigated using mineralogy and material science research methods. The results showed corrosion scale was predominantly composed of goethite, lepidocrocite, hematite, magnetite, ferrous oxide, siderite, chrome green and chromite, the same as that of corroded pipe coupons. Hence, corrosion scale can be identified as podiform chromite deposit. The loss of chromium in passive film is a critical phenomenon when stainless steel passive film is damaged by localized corrosion. This may provide key insights toward improving a better comprehension of the formation of stainless steel corrosion scale and the process of localized corrosion. The localized corrosion behavior of stainless steel is directly connected with reclaimed water quality parameters such as residual chlorine, DO, Cl(-) and SO4(2-). In particular, when a certain amount of residual chlorine in reclaimed water is present as an oxidant, ferric iron is the main chemical state of iron minerals.

  10. Biofilm formation by Listeria monocytogenes on stainless steel surface and biotransfer potential

    Directory of Open Access Journals (Sweden)

    Maíra Maciel Mattos de Oliveira

    2010-03-01

    Full Text Available An experimental model was proposed to study biofilm formation by Listeria monocytogenes ATCC 19117 on AISI 304 (#4 stainless steel surface and biotransfer potential during this process. In this model, biofilm formation was conducted on the surface of stainless steel coupons, set on a stainless steel base with 4 divisions, each one supporting 21 coupons. Trypic Soy Broth was used as bacterial growth substrate, with incubation at 37 ºC and stirring of 50 rpm. The number of adhered cells was determined after 3, 48, 96, 144, 192 and 240 hours of biofilm formation and biotransfer potential from 96 hours. Stainless steel coupons were submitted to Scanning Electron Microscopy (SEM after 3, 144 and 240 hours. Based on the number of adhered cells and SEM, it was observed that L. monocytogenes adhered rapidly to the stainless steel surface, with mature biofilm being formed after 240 hours. The biotransfer potential of bacterium to substrate occurred at all the stages analyzed. The rapid capacity of adhesion to surface, combined with biotransfer potential throughout the biofilm formation stages, make L. monocytogenes a potential risk to the food industry. Both the experimental model developed and the methodology used were efficient in the study of biofilm formation by L. monocytogenes on stainless steel surface and biotransfer potential.

  11. The coupon collector urn model with unequal probabilities in ecology and evolution.

    Science.gov (United States)

    Zoroa, N; Lesigne, E; Fernández-Sáez, M J; Zoroa, P; Casas, J

    2017-02-01

    The sequential sampling of populations with unequal probabilities and with replacement in a closed population is a recurrent problem in ecology and evolution. Examples range from biodiversity sampling, epidemiology to the estimation of signal repertoire in animal communication. Many of these questions can be reformulated as urn problems, often as special cases of the coupon collector problem, most simply expressed as the number of coupons that must be collected to have a complete set. We aimed to apply the coupon collector model in a comprehensive manner to one example-hosts (balls) being searched (draws) and parasitized (ball colour change) by parasitic wasps-to evaluate the influence of differences in sampling probabilities between items on collection speed. Based on the model of a complete multinomial process over time, we define the distribution, distribution function, expectation and variance of the number of hosts parasitized after a given time, as well as the inverse problem, estimating the sampling effort. We develop the relationship between the risk distribution on the set of hosts and the speed of parasitization and propose a more elegant proof of the weak stochastic dominance among speeds of parasitization, using the concept of Schur convexity and the 'Robin Hood transfer' numerical operation. Numerical examples are provided and a conjecture about strong dominance-an ordering characteristic of random variables-is proposed. The speed at which new items are discovered is a function of the entire shape of the sampling probability distribution. The sole comparison of values of variances is not sufficient to compare speeds associated with different distributions, as generally assumed in ecological studies. © 2017 The Author(s).

  12. By-Pass Diode Temperature Tests of a Solar Array Coupon under Space Thermal Environment Conditions

    Science.gov (United States)

    Wright, Kenneth H.; Schneider, Todd A.; Vaughn, Jason A.; Hoang, Bao; Wong, Frankie; Wu, Gordon

    2016-01-01

    By-Pass diodes are a key design feature of solar arrays and system design must be robust against local heating, especially with implementation of larger solar cells. By-Pass diode testing was performed to aid thermal model development for use in future array designs that utilize larger cell sizes that result in higher string currents. Testing was performed on a 56-cell Advanced Triple Junction solar array coupon provided by SSL. Test conditions were vacuum with cold array backside using discrete by-pass diode current steps of 0.25 A ranging from 0 A to 2.0 A.

  13. Microbially induced corrosion of carbon steel in deep groundwater environment

    Directory of Open Access Journals (Sweden)

    Pauliina eRajala

    2015-07-01

    Full Text Available The metallic low and intermediate level radioactive waste generally consists of carbon steel and stainless steels. The corrosion rate of carbon steel in deep groundwater is typically low, unless the water is very acidic or microbial activity in the environment is high. Therefore, the assessment of microbially induced corrosion of carbon steel in deep bedrock environment has become important for evaluating the safety of disposal of radioactive waste. Here we studied the corrosion inducing ability of indigenous microbial community from a deep bedrock aquifer. Carbon steel coupons were exposed to anoxic groundwater from repository site 100 m depth (Olkiluoto, Finland for periods of three and eight months. The experiments were conducted at both in situ temperature and room temperature to investigate the response of microbial population to elevated temperature. Our results demonstrate that microorganisms from the deep bedrock aquifer benefit from carbon steel introduced to the nutrient poor anoxic deep groundwater environment. In the groundwater incubated with carbon steel the planktonic microbial community was more diverse and 100-fold more abundant compared to the environment without carbon steel. The betaproteobacteria were the most dominant bacterial class in all samples where carbon steel was present, whereas in groundwater incubated without carbon steel the microbial community had clearly less diversity. Microorganisms induced pitting corrosion and were found to cluster inside the corrosion pits. Temperature had an effect on the species composition of microbial community and also affected the corrosion deposits layer formed on the surface of carbon steel.

  14. Stormy Weather

    Institute of Scientific and Technical Information of China (English)

    2012-01-01

    Inspired by the deep abyss of the unknown; a constant source for investigation and discovery, heating and destruction, all simultaneously. Beneath the deep darkness, millions of species vibrantly thrive in another universe wholly untouched by human hands, though affected by their choices. The weathered pieces and people associated with seaside villages, the deep wrinkles that tell a story of one's life and experiences like

  15. One period coupon bond valuation with revised first passage time approach and the application in Indonesian corporate bond

    Science.gov (United States)

    Maruddani, Di Asih I.; Rosadi, Dedi; Gunardic, Abdurakhman

    2015-02-01

    The value of a corporate bond is conventionally expressed in terms of zero coupon bond. In practice, the most common form of debt instrument is coupon bond and allows early default before maturity as safety covenant for the bondholder. This paper study valuation for one period coupon bond, a coupon bond that only give one time coupon at the bond period. It assumes that the model give bondholder the right to reorganize a firm if its value falls below a given barrier. Revised first passage time approach is applied for default time rule. As a result, formulas of equity, liability, and probability of default is derived for this specified model. Straightforward integration under risk neutral pricing is used for deriving those formulas. For the application, bond of Bank Rakyat Indonesia (BRI) as one of the largest bank in Indonesia is analyzed. R computing show that value of the equity is IDR 453.724.549.000.000, the liability is IDR 2.657.394.000.000, and the probability if default is 5.645305E-47 %.

  16. Behavior of AISI SAE 1020 Steel Implanted by Titanium and Exposed to Bacteria Sulphate Deoxidizer

    Science.gov (United States)

    Niño, Ely Dannier V.; Garnica, Hernán; Dugar-Zhabon, Veleriy; Castillo, Genis

    2014-05-01

    A hybrid technology to treat solid surfaces with the pulse high voltage and electric arc discharges of low pressure with a three-dimensional ion implantation technique (3DII) is applied. This technology is used to protect AISI SAE 1020 steel against a microbiological corrosion. The titanium ion implanted steel samples (coupons) are subjected to a medium of bacteria sulphate deoxidizer (BSD) which are very typical of the hydrocarbon industry and are potentially harmful for structures when are in contact with petroleum and some of its derivatives. The used technology aims to find an effective hybrid procedure to minimize the harmful effects of bacteria on AISI SAE 1020 steel. The hybrid technology efficiency of superficial titanium implantation is estimated through the measurements of the point corrosion characteristics obtained after testing both the treated and non-treated coupons. The three-dimensional surface structures of the samples are reconstructed with help of a confocal microscope.

  17. Simulating microbiologically influenced corrosion by depositing extracellular biopolymers on mild steel surfaces

    Energy Technology Data Exchange (ETDEWEB)

    Roe, F.L.; Lewandowski, Z.; Funk, T. [Montana State Univ., Bozeman, MT (United States). Center for Biofilm Engineering

    1996-10-01

    Electrochemical properties of corroding mild steel (MS) surfaces were measured in real time using three closely spaced microelectrodes. Dissolved oxygen, pH, and ion currents were mapped simultaneously and noninvasively above a MS coupon partially coated with biopolymer gels. Calcium alginate (Ca-Alg [an extracellular biopolymer containing carboxylate functional groups]) and agarose (one without carboxylate functional groups) were tested. Corrosion occurred at approximately the same rate under the two biopolymer spots on the same coupon. Corrosion rates under these biopolymers were {approx} 4 mpy in a weak saline solution. Results suggested corrosion was not influenced by chemical properties of the biopolymer but possibly was controlled by oxygen reduction in noncoated regions of the coupon (i.e., a differential aeration cell).

  18. Work of adhesion of dairy products on stainless steel surface

    Directory of Open Access Journals (Sweden)

    Patrícia Campos Bernardes

    2012-12-01

    Full Text Available The adhesion of the solids presents in food can difficult the process of surface cleaning and promotes the bacterial adhesion process and can trigger health problems. In our study, we used UHT whole milk, chocolate based milk and infant formula to evaluate the adhesion of Enterobacter sakazakii on stainless steel coupons, and we determine the work of adhesion by measuring the contact angle as well as measured the interfacial tension of the samples. Inaddition we evaluated the hydrophobicity of stainless steel after pre-conditioning with milk samples mentioned. E. sakazakii was able to adhere to stainless steel in large numbers in the presence of dairy products. The chocolate based milk obtained the lower contact angle with stainless steel surface, higher interfacial tension and consequently higher adhesion work. It was verified a tendency of decreasing the interfacial tension as a function of the increasing of protein content. The pre-conditioning of the stainless steel coupons with milk samples changed the hydrophobic characteristics of the surfaces and became them hydrophilic. Therefore, variations in the composition of the milk products affect parameters important that can influence the procedure of hygiene in surface used in food industry.

  19. Polymeric coupling agents for enhancing the adhesion of epoxy to steel

    Science.gov (United States)

    Vaideeswaran, Karthik

    The work described in this dissertation involves the conceptualization, design, development and testing of new polymers for their efficiency as coupling agents to enhance the bonding of steel to epoxy. Two novel series of polymeric coupling agents have been tested viz., a quinone-amine polyurethane (QAP) series and a beta-diketone functionalized polymer (BFP) series. Several QAP and BFP polymers were synthesized and studied. These polymers were characterized using Infrared spectroscopy, thermal analyses (Thermogravimetric Analysis, Differential Scanning Calorimetry) and Gel Permeation Chromatography. The surfaces of QAP and BFP polymeric coupling agent treated steel coupons were analyzed using Infrared Reflection Spectroscopy, Scanning Electron Microscopy and X-ray Photoelectron Spectroscopy. These tests gave indications that the QAPs and BFPs interact with the steel surface chemically. The QAPs and BFPs were found to be very effective coupling agents for the steel-epoxy system. The coupling agent treated epoxy-steel torsional joints were tested (in dry and wet environments) in shear. The QAPs were compared with commercial silanes and demonstrated a 10-15% better strength retention and hot water durability. The QAP treated and epoxy resin topcoated steel coupons demonstrated excellent corrosion resistance when tested in a lab-scale salt-spray chamber. The process conditions (in the coupling agent based polymer coating process for steel described in this dissertation) are mild and process control is relatively simple. This organic coating process is more environmentally friendly than other conventionally used toxic processes for steel like Chrome Etching.

  20. Galvanizability of Advanced High-Strength Steels 1180TRIP and 1180CP

    Science.gov (United States)

    Kim, M. S.; Kwak, J. H.; Kim, J. S.; Liu, Y. H.; Gao, N.; Tang, N.-Y.

    2009-08-01

    In general, Si-bearing advanced high-strength steels (AHSS) possess excellent mechanical properties but poor galvanizability. The galvanizability of a transformation-induced plasticity (TRIP) steel 1180TRIP containing 2.2 pct Mn and 1.7 pct Si and a complex phase steel 1180CP containing 2.7 pct Mn and 0.2 pct Si was extensively studied using a galvanizing simulator. The steel coupons were annealed at fixed dew points in the simulator. The surface features of the as-annealed steel coupons, together with galvanized and galvannealed coatings, were carefully examined using a variety of advanced analysis techniques. It was found that various oxides formed on the surface of these steels, depending on the steel composition and on the dew point control. Coating quality was good at 0 °C dew point but deteriorated as the dew point decreased to -35 °C and -65 °C. Based on the findings, guidance was provided for improving galvanizability by adjusting the Mn:Si ratio in steel compositions according to the dew point.

  1. Predicting Failure Progression and Failure Loads in Composite Open-Hole Tension Coupons

    Science.gov (United States)

    Arunkumar, Satyanarayana; Przekop, Adam

    2010-01-01

    Failure types and failure loads in carbon-epoxy [45n/90n/-45n/0n]ms laminate coupons with central circular holes subjected to tensile load are simulated using progressive failure analysis (PFA) methodology. The progressive failure methodology is implemented using VUMAT subroutine within the ABAQUS(TradeMark)/Explicit nonlinear finite element code. The degradation model adopted in the present PFA methodology uses an instantaneous complete stress reduction (COSTR) approach to simulate damage at a material point when failure occurs. In-plane modeling parameters such as element size and shape are held constant in the finite element models, irrespective of laminate thickness and hole size, to predict failure loads and failure progression. Comparison to published test data indicates that this methodology accurately simulates brittle, pull-out and delamination failure types. The sensitivity of the failure progression and the failure load to analytical loading rates and solvers precision is demonstrated.

  2. Annealing to Mitigate Pitting in Electropolished Niobium Coupons and SRF Cavities

    Energy Technology Data Exchange (ETDEWEB)

    Cooley, L.D.; Hahn, E.; Hicks, D.; Romanenko, A.; Schuessler, R.; Thompson, C.; /Fermilab

    2011-06-08

    Ongoing studies at Fermilab investigate whether dislocations and other factors instigate pitting during cavity electropolishing (EP), despite careful processing controls and the inherent leveling mechanism of EP itself. Here, cold-worked niobium coupons, which exhibited increased tendencies for pitting in our past study, were annealed in a high vacuum furnace and subsequently processed by EP. Laser confocal scanning microscopy and special defect counting algorithms were used to assess the population of pits formed. Hardness measurements indicated that annealing for 2 hours at 800 C produced recovery, whereas annealing for 12 hours at 600 C did not, as is consistent with known changes for cavities annealed in a similar way. The 800 C anneal was effective in some cases but not others, and we discuss reasons why tendencies for pitting remain. We discuss implications for cavities and continued work to understand pitting.

  3. Testing and Model Correlation of Sublimator Driven Coldplate Coupons and EDU

    Science.gov (United States)

    Leimkuehler, Thomas O.

    2009-01-01

    The Sublimator Driven Coldplate (SDC) is a unique piece of thermal control hardware that has several advantages over a more traditional thermal control system. The principal advantage is the possible elimination of a pumped fluid loop, potentially saving mass, power, and complexity. Because this concept relies on evaporative heat rejection techniques, it is primarily useful for short mission durations. Additionally, the concept requires a conductive path between the heat-generating component and the heat rejection device. Therefore, it is mostly a relevant solution for a vehicle with a relatively low heat rejection requirement and/or short transport distances. Tests were performed on coupons and an Engineering Development Unit (EDU) at NASA s Johnson Space Center to better understand the basic operational principles and to validate the analytical methods being used for the SDC development. This paper outlines the results of the SDC tests, the subsequent thermal model correlation, and a description of the SDC Engineering Development Unit test results.

  4. Combined Space Environmental Exposure Tests of Multi-Junction GaAs/Ge Solar Array Coupons

    Science.gov (United States)

    Hoang, Bao; Wong, Frankie; Corey, Ron; Gardiner, George; Funderburk, Victor V.; Gahart, Richard; Wright, Kenneth H.; Schneider, Todd; Vaughn, Jason

    2010-01-01

    A set of multi-junction GaAs/Ge solar array test coupons were subjected to a sequence of 5-year increments of combined environmental exposure tests. The purpose of this test program is to understand the changes and degradation of the solar array panel components, including its ESD mitigation design features in their integrated form, after multiple years (up to 15) of simulated geosynchronous space environment. These tests consist of: UV radiation, electrostatic discharge (ESD), electron/proton particle radiation, thermal cycling, and ion thruster plume exposures. The solar radiation was produced using a Mercury-Xenon lamp with wavelengths in the UV spectrum ranging from 230 to 400 nm. The ESD test was performed in the inverted-gradient mode using a low-energy electron (2.6 - 6 keV) beam exposure. The ESD test also included a simulated panel coverglass flashover for the primary arc event. The electron/proton radiation exposure included both 1.0 MeV and 100 keV electron beams simultaneous with a 40 keV proton beam. The thermal cycling included simulated transient earth eclipse for satellites in geosynchronous orbit. With the increasing use of ion thruster engines on many satellites, the combined environmental test also included ion thruster exposure to determine whether solar array surface erosion had any impact on its performance. Before and after each increment of environmental exposures, the coupons underwent visual inspection under high power magnification and electrical tests that included characterization by LAPSS, Dark I-V, and electroluminescence. This paper discusses the test objective, test methodologies, and preliminary results after 5 years of simulated exposure.

  5. 27 CFR 555.34 - Replacement of stolen or lost ATF Form 5400.30 (Intrastate Purchase of Explosives Coupon (IPEC)).

    Science.gov (United States)

    2010-04-01

    ... lost ATF Form 5400.30 (Intrastate Purchase of Explosives Coupon (IPEC)). 555.34 Section 555.34 Alcohol... or lost ATF Form 5400.30 (Intrastate Purchase of Explosives Coupon (IPEC)). When any Form 5400.30 is... the Director by telephoning 1-888-ATF-BOMB (nationwide toll free number). The report will explain in...

  6. Microbial Corrosion and Cracking in Steel

    DEFF Research Database (Denmark)

    Hilbert, Lisbeth Rischel

    1998-01-01

    and for recommendations in regards to electrochemical monitoring of MIC. The work presented here and further studies are also planned to lead to a Ph.D. thesis on "MIC monitoring based on mechanisms of corrosion".The results of laboratory experiments conducted in the period 1995 to 1997 are summarised. Conclusions...... will be based on results from the entire 3 year period, but only selected experimental data primarily from the latest experiments will be presented in detail here.Microbial corrosion of carbon steel under influence of sulphate-reducing bacteria (SRB) is characterised by the formation of both biofilm...... and corrosion products (ferrous sulphides) on the metal surface. Experiments have been conducted on carbon steel exposed in near neutral (pH 6 to 8.5) saline hydrogen sulphide environment (0 to 100 mg/l total dissolved sulphide) for a period of 14 days. Furthermore coupons have been exposed in a bioreactor...

  7. Monthly Weather Review

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Supplements to the Monthly Weather Review publication. The Weather Bureau published the Monthly weather review Supplement irregularly from 1914 to 1949. The...

  8. Weather Prediction Models

    Science.gov (United States)

    Bacmeister, Julio T.

    Awareness of weather and concern about weather in the proximate future certainly must have accompanied the emergence of human self-consciousness. Although weather is a basic idea in human existence, it is difficult to define precisely.

  9. Nanoparticle Treated Stainless Steel Filters for Metal Vapor Sequestration

    Science.gov (United States)

    Murph, Simona E. Hunyadi; Larsen, George K.; Korinko, Paul; Coopersmith, Kaitlin J.; Summer, Ansley J.; Lewis, Rebecca

    2017-02-01

    The ability to sequester vapor phase radioactive compounds during industrial processes reduces the exposure of workers and the environment to dangerous radioactive materials. Nanomaterials have a lot of potential in this area because they typically demonstrate size- and shape-dependent properties with higher reactivity than bulk. This is due to the increased surface area-to-volume ratio and quantum size effects. In this report, we developed a gold nanomaterial-treated stainless steel filter, namely wools and coupons, that can be efficiently used for zinc vapor sequestration. Without nanoparticle modification, stainless steel coupons do not react or alloy with Zn. Gold nanomaterials were grown onto various stainless steel filters using solution chemistry that is amenable to scaling up. Materials were characterized by electron microscopy, inductively coupled plasma mass spectroscopy and dynamic light scattering before and after exposure to zinc vapors. X-ray diffraction, high-resolution transmission electron microscopy, energy dispersive x-ray spectroscopy mapping and ultraviolet-visible spectroscopy confirm the formation of gold-zinc alloys after Zn vapor exposure. The effect of surface topography on nanoparticle morphology, size and loading density were also investigated, and stainless steel surface defects were found to have an impact on the Au NP growth and subsequently Zn sequestration.

  10. Nanoparticle Treated Stainless Steel Filters for Metal Vapor Sequestration

    Science.gov (United States)

    Murph, Simona E. Hunyadi; Larsen, George K.; Korinko, Paul; Coopersmith, Kaitlin J.; Summer, Ansley J.; Lewis, Rebecca

    2016-12-01

    The ability to sequester vapor phase radioactive compounds during industrial processes reduces the exposure of workers and the environment to dangerous radioactive materials. Nanomaterials have a lot of potential in this area because they typically demonstrate size- and shape-dependent properties with higher reactivity than bulk. This is due to the increased surface area-to-volume ratio and quantum size effects. In this report, we developed a gold nanomaterial-treated stainless steel filter, namely wools and coupons, that can be efficiently used for zinc vapor sequestration. Without nanoparticle modification, stainless steel coupons do not react or alloy with Zn. Gold nanomaterials were grown onto various stainless steel filters using solution chemistry that is amenable to scaling up. Materials were characterized by electron microscopy, inductively coupled plasma mass spectroscopy and dynamic light scattering before and after exposure to zinc vapors. X-ray diffraction, high-resolution transmission electron microscopy, energy dispersive x-ray spectroscopy mapping and ultraviolet-visible spectroscopy confirm the formation of gold-zinc alloys after Zn vapor exposure. The effect of surface topography on nanoparticle morphology, size and loading density were also investigated, and stainless steel surface defects were found to have an impact on the Au NP growth and subsequently Zn sequestration.

  11. Atmospheric corrosion of carbon steel resulting from short term exposures

    Energy Technology Data Exchange (ETDEWEB)

    Balasubramanian, R.; Cook, D.C.; Perez, T.; Reyes, J. [Department of Physics, Old Dominion University, Norfolk, VA 23529 (United States)

    1998-12-31

    The study of corrosion products from short term atmospheric exposures of carbon steel, is very important to understand the processes that lead to corrosion of steels, and ultimately improve the performance of such steel in highly corrosive environments. Many regions along the Gulf of Mexico have extremely corrosive environments due to high mean annual temperature, humidity, time-of-wetness and every high atmospheric pollutants. The process the formation of corrosion products resulting from short term exposure of carbon steel, both as a function of environmental conditions and exposure time, has been investigated. Two sets of coupons were exposed at marine and marine locations, in Campeche, Mexico. Each set was exposed between 1 and 12 months to study the corrosion as a function of time. During the exposure periods, the relative humidity, rainfall, mean temperature, wind speed and wind direction were monitored along with the chloride and sulfur dioxide concentrations in the air. The corroded coupons were analyzed by Moessbauer, Raman, Infrared spectroscopies and X-ray diffraction in order to completely identify the oxides and map their location in the corrosion coating. Scattering and transmission Moessbauer analysis showed some layering of the oxides with lepidocrocite and akaganeite closer to the surface. The fraction of akaganeite phase increased at sites with higher chloride concentrations. A detailed analysis on the development of the oxide phases as a function of exposure time and environmental conditions will be presented. (Author)

  12. Steel making

    CERN Document Server

    Chakrabarti, A K

    2014-01-01

    "Steel Making" is designed to give students a strong grounding in the theory and state-of-the-art practice of production of steels. This book is primarily focused to meet the needs of undergraduate metallurgical students and candidates for associate membership examinations of professional bodies (AMIIM, AMIE). Besides, for all engineering professionals working in steel plants who need to understand the basic principles of steel making, the text provides a sound introduction to the subject.Beginning with a brief introduction to the historical perspective and current status of steel making together with the reasons for obsolescence of Bessemer converter and open hearth processes, the book moves on to: elaborate the physiochemical principles involved in steel making; explain the operational principles and practices of the modern processes of primary steel making (LD converter, Q-BOP process, and electric furnace process); provide a summary of the developments in secondary refining of steels; discuss principles a...

  13. Steel Spring

    Institute of Scientific and Technical Information of China (English)

    2009-01-01

    Tarnished Hebei Iron and Steel Group regains chance to shine A lthough it is too early to tell whether the steel-making sector has emerged [from its gloom, a big divide is openling between China’s large and small producers. While most of the marginal players are still reeling from a market contagion, steel titans like the Shanghai-based Baosteel

  14. Weather in Your Life.

    Science.gov (United States)

    Kannegieter, Sandy; Wirkler, Linda

    Facts and activities related to weather and meteorology are presented in this unit. Separate sections cover the following topics: (1) the water cycle; (2) clouds; (3) the Beaufort Scale for rating the speed and force of wind; (4) the barometer; (5) weather prediction; (6) fall weather in Iowa (sleet, frost, and fog); (7) winter weather in Iowa…

  15. Nonlinear Aeroelastic Analysis of the HIAD TPS Coupon in the NASA 8' High Temperature Tunnel: Theory and Experiment

    Science.gov (United States)

    Goldman, Benjamin D.; Scott, Robert C,; Dowell, Earl H.

    2014-01-01

    The purpose of this work is to develop a set of theoretical and experimental techniques to characterize the aeroelasticity of the thermal protection system (TPS) on the NASA Hypersonic Inflatable Aerodynamic Decelerator (HIAD). A square TPS coupon experiences trailing edge oscillatory behavior during experimental testing in the 8' High Temperature Tunnel (HTT), which may indicate the presence of aeroelastic flutter. Several theoretical aeroelastic models have been developed, each corresponding to a different experimental test configuration. Von Karman large deflection theory is used for the plate-like components of the TPS, along with piston theory for the aerodynamics. The constraints between the individual TPS layers and the presence of a unidirectional foundation at the back of the coupon are included by developing the necessary energy expressions and using the Rayleigh Ritz method to derive the nonlinear equations of motion. Free vibrations and limit cycle oscillations are computed and the frequencies and amplitudes are compared with accelerometer and photogrammetry data from the experiments.

  16. Monitoring Techniques for Microbially Influenced Corrosion of Carbon Steel

    DEFF Research Database (Denmark)

    Hilbert, Lisbeth Rischel

    2000-01-01

    Abstract Monitoring Techniques for Microbially Influenced Corrosion of Carbon Steel Microbially influenced corrosion (MIC) of carbon steel may occur in media with microbiological activity of especially sulphate-reducing bacteria, e.g. on pipelines buried in soil and on marine structures. MIC...... of carbon steel must be monitored on-line in order to provide an efficient protection and control the corrosion. A number of monitoring techniques is industrially used today, and the applicability and reliability of these for monitoring MIC is evaluated. Coupons and ER are recommended as necessary basic...... techniques even though localised corrosion rate cannot be measured. FSM measures general corrosion and detects localised corrosion, but the sensitivity is not high enough for monitoring initiation of pitting and small attacks. Electrochemical techniques as LPR and EIS give distorted data and unreliable...

  17. Monitoring Techniques for Microbially Influenced Corrosion of Carbon Steel

    DEFF Research Database (Denmark)

    Hilbert, Lisbeth Rischel

    2000-01-01

    Microbially influenced corrosion (MIC) of carbon steel may occur in media with microbiological activity of especially sulphate-reducing bacteria, e.g. on pipelines buried in soil and on marine structures. MIC of carbon steel must be monitored on-line in order to provide an efficient protection...... corrosion and detects localised corrosion, but the sensitivity is not high enough for monitoring initiation of pitting and small attacks. Electrochemical techniques as LPR and EIS give distorted data and unreliable corrosion rates, when biofilm and corrosion products cover the steel surface. However, EIS...... and control the corrosion. A number of monitoring techniques is industrially used today, and the applicability and reliability of these for monitoring MIC is evaluated. Coupons and ER are recommended as necessary basic techniques even though localised corrosion rate cannot be measured. FSM measures general...

  18. Monitoring Techniques for Microbially Influenced Corrosion of Carbon Steel

    DEFF Research Database (Denmark)

    Hilbert, Lisbeth Rischel

    2000-01-01

    of carbon steel must be monitored on-line in order to provide an efficient protection and control the corrosion. A number of monitoring techniques is industrially used today, and the applicability and reliability of these for monitoring MIC is evaluated. Coupons and ER are recommended as necessary basic......Abstract Monitoring Techniques for Microbially Influenced Corrosion of Carbon Steel Microbially influenced corrosion (MIC) of carbon steel may occur in media with microbiological activity of especially sulphate-reducing bacteria, e.g. on pipelines buried in soil and on marine structures. MIC...... techniques even though localised corrosion rate cannot be measured. FSM measures general corrosion and detects localised corrosion, but the sensitivity is not high enough for monitoring initiation of pitting and small attacks. Electrochemical techniques as LPR and EIS give distorted data and unreliable...

  19. Monitoring Techniques for Microbially Influenced Corrosion of Carbon Steel

    DEFF Research Database (Denmark)

    Hilbert, Lisbeth Rischel

    2000-01-01

    and control the corrosion. A number of monitoring techniques is industrially used today, and the applicability and reliability of these for monitoring MIC is evaluated. Coupons and ER are recommended as necessary basic techniques even though localised corrosion rate cannot be measured. FSM measures general......Microbially influenced corrosion (MIC) of carbon steel may occur in media with microbiological activity of especially sulphate-reducing bacteria, e.g. on pipelines buried in soil and on marine structures. MIC of carbon steel must be monitored on-line in order to provide an efficient protection...... corrosion and detects localised corrosion, but the sensitivity is not high enough for monitoring initiation of pitting and small attacks. Electrochemical techniques as LPR and EIS give distorted data and unreliable corrosion rates, when biofilm and corrosion products cover the steel surface. However, EIS...

  20. Feynman perturbation expansion for the price of coupon bond options and swaptions in quantum finance. II. Empirical.

    Science.gov (United States)

    Baaquie, Belal E; Liang, Cui

    2007-01-01

    The quantum finance pricing formulas for coupon bond options and swaptions derived by Baaquie [Phys. Rev. E 75, 016703 (2006)] are reviewed. We empirically study the swaption market and propose an efficient computational procedure for analyzing the data. Empirical results of the swaption price, volatility, and swaption correlation are compared with the predictions of quantum finance. The quantum finance model generates the market swaption price to over 90% accuracy.

  1. Ultrasonic Welding of Thermoplastic Composite Coupons for Mechanical Characterization of Welded Joints through Single Lap Shear Testing.

    Science.gov (United States)

    Villegas, Irene F; Palardy, Genevieve

    2016-02-11

    This paper presents a novel straightforward method for ultrasonic welding of thermoplastic-composite coupons in optimum processing conditions. The ultrasonic welding process described in this paper is based on three main pillars. Firstly, flat energy directors are used for preferential heat generation at the joining interface during the welding process. A flat energy director is a neat thermoplastic resin film that is placed between the parts to be joined prior to the welding process and heats up preferentially owing to its lower compressive stiffness relative to the composite substrates. Consequently, flat energy directors provide a simple solution that does not require molding of resin protrusions on the surfaces of the composite substrates, as opposed to ultrasonic welding of unreinforced plastics. Secondly, the process data provided by the ultrasonic welder is used to rapidly define the optimum welding parameters for any thermoplastic composite material combination. Thirdly, displacement control is used in the welding process to ensure consistent quality of the welded joints. According to this method, thermoplastic-composite flat coupons are individually welded in a single lap configuration. Mechanical testing of the welded coupons allows determining the apparent lap shear strength of the joints, which is one of the properties most commonly used to quantify the strength of thermoplastic composite welded joints.

  2. Financialisation and the coupon pool Financeirização e a aposta em dividendos

    Directory of Open Access Journals (Sweden)

    Julie Froud

    2001-12-01

    Full Text Available By the late 1990s, shareholder value was the explicit, new priority for the old corporations in the US and UK where the stock market had gained an unprecedented influence on the behaviour of giant corporations. The business press obsessively discussed which managements were, and were not, delivering value and all the major US consulting firms had moved into selling value metrics and implementation packages promising to solve this question. Over this decade, share prices rose unsteadily in a long bull market which ended in the tech stock crash of Spring 2000 which, one year later, had turned into a bear market in a slowing US economy. All this poses new questions about what’s at stake in the capital market's pressure on corporations for increased returns; and what's behind higher share prices and their collapse? The intellectual responses widened the debate but has led to increasing conceptual confusion: the journalistic term "shareholder value" has passed into academic usage; while neologisms such as financialisation are used differently by various authors. Against this background, our paper aims to discuss the existing terms and main definitions and to argue for a redefinition of the problem around a new generic concept of coupon pool capitalism. After this, the paper presents a brief empirical analysis of the dynamics of the coupon pool in the USA and UK. This analysis represents part of our answer to the question of what's new and different about the current forms of capitalism.O artigo descreve as mudanças recentes nas formas de funcionamento do capitalismo contemporâneo baseada no papel autônomo alcançado pela esfera financeira. Discutindo com várias propostas de explicação do fenômeno, ele propõe uma explicação que acentua o caráter ao mesmo tempo paradoxal, contingente e contraditório do processo que estamos vivendo. A forma atual é originária dos países anglo-saxões e se espraia rumo aos demais países desenvolvidos e

  3. Examination of Compatibility of Potentially Cavitation-Resistant Modifications of Type 316LN Stainless Steel with Mercury in a Thermal Convection Loop

    Energy Technology Data Exchange (ETDEWEB)

    Pawel, SJ

    2002-08-29

    A 316L stainless steel thermal convection loop (TCL) containing a variety of stainless steel coupons circulated mercury for 2000 h. The TCL conditions included a maximum temperature of 307 C, a maximum temperature gradient of 90 C, and a Hg velocity of about 1.4 m/min. In addition to mill-annealed/surface-ground 316LN coupons serving as the baseline material, other coupons included 316LN that was 50% cold-worked, 316LN that was given a proprietary surface hardening treatment termed ''kolsterizing,'' and Nitronic 60. The purpose of this test was to examine Hg compatibility with these modest variations of annealed 31 6LN stainless steel that are considered potential improvements over annealed 31 6LN for cavitation-erosion resistance in the Spallation Neutron Source (SNS) target containment system. The results indicated negligible weight change for each coupon type, no significant indication of attack or surface roughening, and generally no interaction with Hg.

  4. Tool steels

    DEFF Research Database (Denmark)

    Højerslev, C.

    2001-01-01

    On designing a tool steel, its composition and heat treatment parameters are chosen to provide a hardened and tempered martensitic matrix in which carbides are evenly distributed. In this condition the matrix has an optimum combination of hardness andtoughness, the primary carbides provide...... resistance against abrasive wear and secondary carbides (if any) increase the resistance against plastic deformation. Tool steels are alloyed with carbide forming elements (Typically: vanadium, tungsten, molybdenumand chromium) furthermore some steel types contains cobalt. Addition of alloying elements...

  5. Investigating early stages of biocorrosion with XPS: AISI 304 stainless steel exposed to Burkholderia species

    Science.gov (United States)

    Johansson, Leena-Sisko; Saastamoinen, Tuomas

    1999-04-01

    We have investigated the interactions of an exopolymer-producing bacteria, Burkholderia sp. with polished AISI 304 stainless steel substrates using X-ray photoelectron spectroscopy (XPS). Steel coupons were exposed to the pure bacteria culture in a specially designed flowcell for 6 h during which the experiment was monitored in situ with an optical microscope. XPS results verified the formation of biofilm containing extracellular polymer on all the samples exposed to bacteria. Sputter results indicated that some ions needed for metabolic processes were trapped within the biofilm. Changes in the relative Fe concentration and Fe 2p peak shape indicated that also iron had accumulated into the biofilm.

  6. Land Surface Weather Observations

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — METAR is the international standard code format for hourly surface weather observations. The acronym roughly translates from French as Aviation Routine Weather...

  7. Project Weather and Water.

    Science.gov (United States)

    Hansen, Pal J. Kirkeby

    2000-01-01

    Introduces Project Weather and Water with the goal of developing and testing ideas of how to implement weather topics and water physics in an integrated way. Discusses teacher preparation, implementation, and evaluation of this project. (ASK)

  8. Pilot Weather Reports

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Aviation weather reports relayed from pilots to FAA air traffic controllers or National Weather Service personnel. Elements include sky cover, turbulence, wind...

  9. Natural Weathering Exposure Station

    Data.gov (United States)

    Federal Laboratory Consortium — The Corps of Engineers' Treat Island Natural Weathering Exposure Station is a long-term natural weathering facility used to study concrete durability. Located on the...

  10. Surface Weather Observations Hourly

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Standard hourly observations taken at Weather Bureau/National Weather Service offices and airports throughout the United States. Hourly observations began during the...

  11. Surface Weather Observing Manuals

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Manuals and instructions for taking weather observations. Includes the annual Weather Bureau 'Instructions for Preparing Meteorological Forms...' and early airways...

  12. Daily Weather Records

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — These daily weather records were compiled from a subset of stations in the Global Historical Climatological Network (GHCN)-Daily dataset. A weather record is...

  13. Winter Weather Emergencies

    Science.gov (United States)

    Severe winter weather can lead to health and safety challenges. You may have to cope with Cold related health problems, including ... there are no guarantees of safety during winter weather emergencies, you can take actions to protect yourself. ...

  14. National Convective Weather Diagnostic

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Current convective hazards identified by the National Convective Weather Detection algorithm. The National Convective Weather Diagnostic (NCWD) is an automatically...

  15. Internet Weather Source

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — The National Weather Service (NWS) National Telecommunications Gateway provides weather, hydrologic, and climate forecasts and warnings for the United States, its...

  16. Weather Radar Stations

    Data.gov (United States)

    Department of Homeland Security — These data represent Next-Generation Radar (NEXRAD) and Terminal Doppler Weather Radar (TDWR) weather radar stations within the US. The NEXRAD radar stations are...

  17. Microbiological test results using three urine pretreatment regimes with 316L stainless steel

    Science.gov (United States)

    Huff, Timothy L.

    1993-01-01

    Three urine pretreatments, (1) Oxone (Dupont) and sulfuric acid, (2) sodium hypochlorite and sulfuric acid, (3) and ozone, were studied for their ability to reduce microbial levels in urine and minimize surface attachment to 316L stainless steel coupons. Urine samples inoculated with Bacillus insolitus and a filamentous mold, organisms previously recovered from the vapor compression distillation subsystem of NASA Space Station Freedom water recovery test were tested in glass corrosion cells containing base or weld metal coupons. Microbial levels, changes in pH, color, turbidity, and odor of the fluid were monitored over the course of the 21-day test. Specimen surfaces were examined by scanning electron microscopy at completion of the test for microbial attachment. Ozonated urine samples were less turbid and had lower microbial levels than controls or samples receiving other pretreatments. Base metal coupons receiving pretreatment were relatively free of attached bacteria. However, well-developed biofilms were found in the heat-affected regions of welded coupons receiving Oxone and hypochlorite pretreatments. Few bacteria were observed in the same regions of the ozone pretreatment sample.

  18. The power of weather

    OpenAIRE

    Christian Huurman; Francesco Ravazzolo; Chen Zhou

    2010-01-01

    This paper examines the predictive power of weather for electricity prices in day ahead markets in real time. We find that next-day weather forecasts improve the forecast accuracy of Scandinavian day-ahead electricity prices substantially in terms of point forecasts, suggesting that weather forecasts can price the weather premium. This improvement strengthens the confidence in the forecasting model, which results in high center-mass predictive densities. In density forecast, such a predictive...

  19. Synergistic effect of steam and lactic acid against Escherichia coli O157:H7, Salmonella Typhimurium, and Listeria monocytogenes biofilms on polyvinyl chloride and stainless steel.

    Science.gov (United States)

    Ban, Ga-Hee; Park, Sang-Hyun; Kim, Sang-Oh; Ryu, Sangryeol; Kang, Dong-Hyun

    2012-07-01

    This study was designed to investigate the individual and combined effects of steam and lactic acid (LA) on the inactivation of biofilms formed by Escherichia coli O157:H7, Salmonella Typhimurium, and Listeria monocytogenes on polyvinyl chloride (PVC) and stainless steel. Six day old biofilms were developed on PVC and stainless steel coupons by using a mixture of three strains each of three foodborne pathogens at 25°C. After biofilm development, PVC and stainless steel coupons were treated with LA alone (immersed in 0.5% or 2% for 5s, 15s, and 30s), steam alone (on both sides for 5, 10, and 20s), and the combination of steam and LA. The numbers of biofilm cells of the three foodborne pathogens were significantly (p<0.05) reduced as the amount of LA and duration of steam exposure increased. There was a synergistic effect of steam and LA on the viability of biofilm cells of the three pathogens. For all biofilm cells of the three foodborne pathogens, reduction levels of individual treatments ranged from 0.11 to 2.12 log CFU/coupon. The combination treatment of steam and LA achieved an additional 0.2 to 2.11 log reduction compared to the sum of individual treatments. After a combined treatment of immersion in 2% LA for 15s or 30s followed by exposure to steam for 20s, biofilm cells of the three pathogens were reduced to below the detection limit (1.48 log). From the results of this study, bacterial populations of biofilms on PVC coupons did not receive the same thermal effect as on stainless steel coupons. Effectiveness of steam and LA may be attributed to the difference between Gram-negative and Gram-positive characteristics of the bacteria studied. The results of this study suggest that the combination of steam and LA has potential as a biofilm control intervention for food processing facilities.

  20. MECHANISTIC UNDERSTANDING OF CAUSTIC CRACKING OF CARBON STEELS

    Energy Technology Data Exchange (ETDEWEB)

    Garcia-Diaz, B.; Roy, A.

    2009-10-19

    Liquid waste generated by the PUREX process for separation of nuclear materials is concentrated and stored in Type IV single-shell carbon steel tanks at the Savannah River Site (SRS). The Type IV tanks for this waste do not have cooling coils and have not undergone heat treatment to stress-relieve the tanks. After the waste is concentrated by evaporation, it becomes very alkaline and can cause stress corrosion cracking (SCC) and pitting corrosion of the tank materials. SRS has experienced leakage from non-stress-relieved waste tanks constructed of A285 carbon steel and pitting of A212 carbon steel tanks in the vapor space. An investigation of tank materials has been undertaken at SRS to develop a basic understanding of caustic SCC of A285 and A212 grade carbon steels exposed to aqueous solutions, primarily containing sodium hydroxide (NaOH), sodium nitrate (NaNO{sub 3}), and sodium nitrite (NaNO{sub 2}) at temperatures relevant to the operating conditions of both the F and H area plants. This report presents the results of this corrosion testing program. Electrochemical tests were designed using unstressed coupons in a simulated tank environment. The purpose of this testing was to determine the corrosion susceptibility of the tank materials as a function of chemical concentration, pH, and temperature. A285 and A516 (simulates A212 carbon steel) coupons were used to investigate differences in the corrosion of these carbon steels. Electrochemical testing included measurement of the corrosion potential and polarization resistance as well as cyclic potentiodynamic polarization (CPP) testing of coupons. From the CPP experiments, corrosion characteristics were determined including: corrosion potential (E{sub corr}), pitting or breakdown potential (E{sub pit}), and repassivation potential (E{sub prot}). CPP results showed no indications of localized corrosion, such as pitting, and all samples showed the formation of a stable passive layer as evidenced by the positive

  1. Weather Fundamentals: Meteorology. [Videotape].

    Science.gov (United States)

    1998

    The videos in this educational series, for grades 4-7, help students understand the science behind weather phenomena through dramatic live-action footage, vivid animated graphics, detailed weather maps, and hands-on experiments. This episode (23 minutes) looks at how meteorologists gather and interpret current weather data collected from sources…

  2. Cold-Weather Sports

    Science.gov (United States)

    ... Surgery? A Week of Healthy Breakfasts Shyness Cold-Weather Sports KidsHealth > For Teens > Cold-Weather Sports A A A What's in this article? ... Equipment Ahh, winter! Shorter days. Frigid temperatures. Foul weather. What better time to be outdoors? Winter sports ...

  3. Convective Weather Avoidance with Uncertain Weather Forecasts

    Science.gov (United States)

    Karahan, Sinan; Windhorst, Robert D.

    2009-01-01

    Convective weather events have a disruptive impact on air traffic both in terminal area and in en-route airspaces. In order to make sure that the national air transportation system is safe and efficient, it is essential to respond to convective weather events effectively. Traffic flow control initiatives in response to convective weather include ground delay, airborne delay, miles-in-trail restrictions as well as tactical and strategic rerouting. The rerouting initiatives can potentially increase traffic density and complexity in regions neighboring the convective weather activity. There is a need to perform rerouting in an intelligent and efficient way such that the disruptive effects of rerouting are minimized. An important area of research is to study the interaction of in-flight rerouting with traffic congestion or complexity and developing methods that quantitatively measure this interaction. Furthermore, it is necessary to find rerouting solutions that account for uncertainties in weather forecasts. These are important steps toward managing complexity during rerouting operations, and the paper is motivated by these research questions. An automated system is developed for rerouting air traffic in order to avoid convective weather regions during the 20- minute - 2-hour time horizon. Such a system is envisioned to work in concert with separation assurance (0 - 20-minute time horizon), and longer term air traffic management (2-hours and beyond) to provide a more comprehensive solution to complexity and safety management. In this study, weather is dynamic and uncertain; it is represented as regions of airspace that pilots are likely to avoid. Algorithms are implemented in an air traffic simulation environment to support the research study. The algorithms used are deterministic but periodically revise reroutes to account for weather forecast updates. In contrast to previous studies, in this study convective weather is represented as regions of airspace that pilots

  4. Weather Conditions, Weather Information and Car Crashes

    Directory of Open Access Journals (Sweden)

    Adriaan Perrels

    2015-11-01

    Full Text Available Road traffic safety is the result of a complex interaction of factors, and causes behind road vehicle crashes require different measures to reduce their impacts. This study assesses how strongly the variation in daily winter crash rates associates with weather conditions in Finland. This is done by illustrating trends and spatiotemporal variation in the crash rates, by showing how a GIS application can evidence the association between temporary rises in regional crash rates and the occurrence of bad weather, and with a regression model on crash rate sensitivity to adverse weather conditions. The analysis indicates that a base rate of crashes depending on non-weather factors exists, and some combinations of extreme weather conditions are able to substantially push up crash rates on days with bad weather. Some spatial causation factors, such as variation of geophysical characteristics causing systematic differences in the distributions of weather variables, exist. Yet, even in winter, non-spatial factors are normally more significant. GIS data can support optimal deployment of rescue services and enhance in-depth quantitative analysis by helping to identify the most appropriate spatial and temporal resolutions. However, the supportive role of GIS should not be inferred as existence of highly significant spatial causation.

  5. Steel Planning

    Institute of Scientific and Technical Information of China (English)

    2011-01-01

    China releases a new plan for the iron and steel industry centered on industrial upgrades The new 12th Five-Year Plan (2011-15) for China’s iron and steel industry, recently released on the website of the Ministry of Industry and Information

  6. Microbial Corrosion and Cracking in Steel

    DEFF Research Database (Denmark)

    Hilbert, Lisbeth Rischel

    1998-01-01

    and corrosion products (ferrous sulphides) on the metal surface. Experiments have been conducted on carbon steel exposed in near neutral (pH 6 to 8.5) saline hydrogen sulphide environment (0 to 100 mg/l total dissolved sulphide) for a period of 14 days. Furthermore coupons have been exposed in a bioreactor...... for a period of up to 120 days in sulphide-producing environment controlled by biological activity of (SRB).Electrochemical studies have been conducted in order to characterise the electrochemical response of the biofilm / ferrous sulphide / metal interface and clarify whether the tested electrochemical...... and not electrochemically active film. The polarisation resistance increases with the film resistance and an small underestimation of corrosion rate is possible, if film resistance is large.· An electrochemically reactive film (ferrous sulphides) results in current contributions that will be added to the metal dissolution...

  7. Weatherization and Intergovernmental Program - Weatherization Assistance Program

    Energy Technology Data Exchange (ETDEWEB)

    None

    2010-06-01

    The U.S. Department of Energy’s (DOE) Weatherization Assistance Program reduces energy costs for low-income households by increasing the energy efficiency of their homes, while ensuring their health and safety.

  8. Transuranic contamination of stainless steel in nitric acid

    Science.gov (United States)

    Kerry, Timothy; Banford, Anthony W.; Thompson, Olivia R.; Carey, Thomas; Schild, Dieter; Geist, Andreas; Sharrad, Clint A.

    2017-09-01

    Stainless steels coupons have been exposed to transuranic species in conditions representative of those found in a spent nuclear fuel reprocessing plant. Stainless steel was prepared to different surface finishes and exposed to nitric acid of varying concentrations containing 237Np, 239Pu or 243Am for one month at 50 °C. Contamination by these transuranics has been observed on all surfaces exposed to the solution through the use of autoradiography. This technique showed that samples held in 4 M HNO3 bind 2-3 times as much radionuclide as those held in 10.5 M HNO3. It was also found that the polished steel surfaces generally took up more transuranic contamination than the etched and ;as received; steel finishes. The extent of corrosion on the steel surfaces was found, by scanning electron microscopy, to be greater in solutions containing Np and Pu in comparison to that observed from contact with Am containing solutions, indicating that redox activity of transuranics can influence the mechanism of stainless steel corrosion.

  9. Fatigue damage observed non-destructively in fibre composite coupon test specimens by X-ray CT

    DEFF Research Database (Denmark)

    Jespersen, Kristine Munk; Mikkelsen, Lars Pilgaard

    2016-01-01

    This study presents a method for monitoring the 3D fatigue damage progression on a micro-structural level in a glass fibre/polymer coupon test specimen by means of laboratory X-ray Computed Tomography (CT). A modified mount and holder made for the standard test samples to fit into the X-ray CT...... scanner along with a tension clamp solution is presented. Initially, the same location of the test specimen is inspected by ex-situ X-ray CT during the fatigue loading history, which shows the damage progression on a micro-structural level. The openings of individual uni-directional (UD) fibre fractures...

  10. Efficacy of gaseous chlorine dioxide in inactivating Bacillus cereus spores attached to and in a biofilm on stainless steel.

    Science.gov (United States)

    Nam, Hyegyeong; Seo, Hyun-Sun; Bang, Jihyun; Kim, Hoikyung; Beuchat, Larry R; Ryu, Jee-Hoon

    2014-10-01

    We evaluated the lethal activity of gaseous chlorine dioxide (ClO2) against Bacillus cereus spores attached to and in biofilm formed on a stainless steel surface. Aqueous ClO2 was prepared by mixing sulfuric acid (5% w/v) with sodium chlorite (10mg/mL), and gaseous ClO2 was produced by vaporization of aqueous ClO2 in an air-tight container. The concentration of gaseous ClO2 in the air within the container increased rapidly at first but gradually decreased over time. The lethality of gaseous ClO2 against B. cereus spores attached to stainless steel coupons (SSCs) and in biofilm formed by the pathogen on SSCs was determined. The B. cereus spores attached to SSCs (5.3±0.1logCFU/coupon) were completely inactivated within 1h at 25°C when treated with gaseous ClO2 (peak concentration: 115.3±5.0 parts per million [ppm]). The total number of vegetative cells and spores in biofilm formed by B. cereus on SSCs was 5.9±0.3logCFU/coupon; the spore count was 5.3±0.1logCFU/coupon. The vegetative cells and spores in biofilm were completely inactivated within 6h (peak concentration: 115.3±5.0ppm). Results show that B. cereus spores in biofilms are more resistant to gaseous ClO2 than are attached spores not in biofilms. Gaseous ClO2 was, nevertheless, very effective in killing B. cereus spores in biofilm on the surface of stainless steel. Results show promise for application of gaseous ClO2 to enhance the microbiological safety of foods that may come in contact with stainless steel and possibly other hard surfaces on which B. cereus biofilms have formed.

  11. Zero-Coupon bond pricing模型的最优系统与群不变解%An optimal system and group-invariant solutions of the Zero-Coupon bond pricing models

    Institute of Scientific and Technical Information of China (English)

    张颖; 高雯

    2009-01-01

    Lie group theory is applied to differential equations occurring as mathematical models in financial problems. The Zero-Coupon bond pricing models are studied. Its one-parameter Lie point symmetries and corresponding group of adjoint representations are obtained. An optimal system of one-dimensional subalgebra is derived and used to construct distinct families of special closed-form solutions of the equation.%将李群理论用于金融问题中出现的数学模型的微分方程,研究了Zero-Coupon bond pricing模型.求出了该模型的单参数李点对称及它相应的群伴随表达式,由此求得该模型允许的一维李群的子代数的最优系统并且利用最优系统构造该模型相应的微分方程的一些特殊的不同类的闭解.

  12. Corrosion of type 316L stainless steel in a mercury thermal convection loop

    Energy Technology Data Exchange (ETDEWEB)

    DiStefano, J.R.; Manneschmidt, E.T.; Pawel, S.J.

    1999-04-01

    Two thermal convection loops fabricated from 316L stainless steel containing mercury (Hg) and Hg with 1000 wppm gallium (Ga), respectively, were operated continuously for about 5000 h. In each case, the maximum loop temperature was constant at about 305 degrees C and the minimum temperature was constant at about 242 degrees C. Coupons in the hot leg of the Hg-loop developed a posous surface layer substantially depleted of nickel and chromium, which resulted in a transformation to ferrite. The coupon exposed at the top of the hot leg in the Hg-loop experienced the maximum degradation, exhibiting a surface layer extending an average of 9-10 mu m after almost 5000 h. Analysis of the corrosion rate data as a function of temperature (position) in the Hg-loop suggests wetting by the mer cury occurred only above about 255 degrees C and that the rate limiting step in the corrosion process above 255 degrees C is solute diffusion through the saturated liquid boundary layer adjacent to the corroding surface. The latter factor suggests that the corrosion of 316L stainless steel in a mercury loop may be velocity dependent. No wetting and no corrosion were observed on the coupons and wall specimens removed from the Hg/Ga loop after 5000 h of operation.

  13. Use of an Electrochemical Split Cell Technique to Evaluate the Influence of Shewanella oneidensis Activities on Corrosion of Carbon Steel.

    Science.gov (United States)

    Miller, Robert Bertram; Sadek, Anwar; Rodriguez, Alvaro; Iannuzzi, Mariano; Giai, Carla; Senko, John M; Monty, Chelsea N

    2016-01-01

    Microbially induced corrosion (MIC) is a complex problem that affects various industries. Several techniques have been developed to monitor corrosion and elucidate corrosion mechanisms, including microbiological processes that induce metal deterioration. We used zero resistance ammetry (ZRA) in a split chamber configuration to evaluate the effects of the facultatively anaerobic Fe(III) reducing bacterium Shewanella oneidensis MR-1 on the corrosion of UNS G10180 carbon steel. We show that activities of S. oneidensis inhibit corrosion of steel with which that organism has direct contact. However, when a carbon steel coupon in contact with S. oneidensis was electrically connected to a second coupon that was free of biofilm (in separate chambers of the split chamber assembly), ZRA-based measurements indicated that current moved from the S. oneidensis-containing chamber to the cell-free chamber. This electron transfer enhanced the O2 reduction reaction on the coupon deployed in the cell free chamber, and consequently, enhanced oxidation and corrosion of that electrode. Our results illustrate a novel mechanism for MIC in cases where metal surfaces are heterogeneously covered by biofilms.

  14. Electrochromic Radiator Coupon Level Testing and Full Scale Thermal Math Modeling for Use on Altair Lunar Lander

    Science.gov (United States)

    Bannon, Erika T.; Bower, Chad E.; Sheth, Rubik; Stephan, Ryan

    2010-01-01

    In order to control system and component temperatures, many spacecraft thermal control systems use a radiator coupled with a pumped fluid loop to reject waste heat from the vehicle. Since heat loads and radiation environments can vary considerably according to mission phase, the thermal control system must be able to vary the heat rejection. The ability to "turn down" the heat rejected from the thermal control system is critically important when designing the system. Electrochromic technology as a radiator coating is being investigated to vary the amount of heat rejected by a radiator. Coupon level tests were performed to test the feasibility of this technology. Furthermore, thermal math models were developed to better understand the turndown ratios required by full scale radiator architectures to handle the various operation scenarios encountered during a mission profile for the Altair Lunar Lander. This paper summarizes results from coupon level tests as well as the thermal math models developed to investigate how electrochromics can be used to increase turn down ratios for a radiator. Data from the various design concepts of radiators and their architectures are outlined. Recommendations are made on which electrochromic radiator concept should be carried further for future thermal vacuum testing.

  15. Benign Weather Modification

    Science.gov (United States)

    2007-11-02

    operational interest in modifying weather to support combat operations increased, ultimately leading to a multi-service effort called PROJECT POPEYE . The goal...This, coupled with the revelations concerning weather modification use in the Vietnam War (PROJECT POPEYE ), was a double blow to weather modification...AWS-TR-74-247, June 1984. Cobb, James T., Jr., et. al. Project Popeye : Final Report. China Lake, CA: Naval Weapons Center, 1967. Langmuir, Irving

  16. Is Weather Chaotic?

    CERN Document Server

    Raidl, A

    1998-01-01

    The correlation dimension and K2-entropy are estimated from meteorological time- series. The results lead us to claim that seasonal variability of weather is under influence of low dimensional dynamics, whereas changes of weather from day to day are governed by high dimensional system(s). Error-doubling time of this system is less than 3 days. We suggest that the outstanding feature of the weather dynamics is deterministic chaos.

  17. Space Weather Laboratory

    Data.gov (United States)

    Federal Laboratory Consortium — The Space Weather Computational Laboratory is a Unix and PC based modeling and simulation facility devoted to research analysis of naturally occurring electrically...

  18. Space Weather Analysis

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Space Weather Analysis archives are model output of ionospheric, thermospheric and magnetospheric particle populations, energies and electrodynamics

  19. Short communication: Evaluation of a sol-gel-based stainless steel surface modification to reduce fouling and biofilm formation during pasteurization of milk.

    Science.gov (United States)

    Liu, Dylan Zhe; Jindal, Shivali; Amamcharla, Jayendra; Anand, Sanjeev; Metzger, Lloyd

    2017-04-01

    Milk fouling and biofilms are common problems in the dairy industry across many types of processing equipment. One way to reduce milk fouling and biofilms is to modify the characteristics of milk contact surfaces. This study examines the viability of using Thermolon (Porcelain Industries Inc., Dickson, TN), a sol-gel-based surface modification of stainless steel, during thermal processing of milk. We used stainless steel 316L (control) and sol-gel-modified coupons in this study to evaluate fouling behavior and bacterial adhesion. The surface roughness as measured by an optical profiler indicated that the control coupons had a slightly smoother finish. Contact angle measurements showed that the modified surface led to a higher water contact angle, suggesting a more hydrophobic surface. The modified surface also had a lower surface energy (32.4 ± 1.4 mN/m) than the control surface (41.36 ± 2.7 mN/m). We evaluated the susceptibility of control and modified stainless steel coupons to fouling in a benchtop plate heat exchanger. We observed a significant reduction in the amount of fouled layer on modified surfaces. We found an average fouling weight of 19.21 mg/cm(2) and 0.37 mg/cm(2) on the control and modified stainless steel coupons, respectively. We also examined the adhesion of Bacillus and biofilm formation, and observed that the modified stainless steel surface offered greater resistance to biofilm formation. Overall, the Thermolon-modified surface showed potential in the thermal processing of milk, offering significantly lower fouling and bacterial attachment than the control surface.

  20. Weather and emotional state

    Science.gov (United States)

    Spasova, Z.

    2010-09-01

    Introduction Given the proven effects of weather on the human organism, an attempt to examine its effects on a psychic and emotional level has been made. Emotions affect the bio-tonus, working ability and concentration, hence their significance in various domains of economic life, such as health care, education, transportation, tourism, etc. Data and methods The research has been made in Sofia City within a period of 8 months, using 5 psychological methods (Eysenck Personality Questionnaire (EPQ), State-Trait Anxiety Inventory (STAI), Test for Self-assessment of the emotional state (developed by Wessman and Ricks), Test for evaluation of moods and Test "Self-confidence - Activity - Mood" (developed by the specialists from the Military Academy in Saint Petersburg). The Fiodorov-Chubukov's complex-climatic method was used to characterize meteorological conditions because of the purpose to include in the analysis a maximal number of meteorological elements. 16 weather types are defined in dependence of the meteorological elements values according to this method. Abrupt weather changes from one day to another, defined by the same method, were considered as well. Results and discussions The results obtained by t-test show that the different categories of weather lead to changes in the emotional status, which indicates a character either positive or negative for the organism. The abrupt weather changes, according to expectations, have negative effect on human emotions but only when a transition to the cloudy weather or weather type, classified as "unfavourable" has been realized. The relationship between weather and human emotions is rather complicated since it depends on individual characteristics of people. One of these individual psychological characteristics, marked by the dimension "neuroticism", has a strong effect on emotional reactions in different weather conditions. Emotionally stable individuals are more "protected" to the weather influence on their emotions

  1. Anaerobic hydrocarbon and fatty acid metabolism by syntrophic bacteria and their impact on carbon steel corrosion.

    Science.gov (United States)

    Lyles, Christopher N; Le, Huynh M; Beasley, William Howard; McInerney, Michael J; Suflita, Joseph M

    2014-01-01

    The microbial metabolism of hydrocarbons is increasingly associated with the corrosion of carbon steel in sulfate-rich marine waters. However, how such transformations influence metal biocorrosion in the absence of an electron acceptor is not fully recognized. We grew a marine alkane-utilizing, sulfate-reducing bacterium, Desulfoglaeba alkanexedens, with either sulfate or Methanospirillum hungatei as electron acceptors, and tested the ability of the cultures to catalyze metal corrosion. Axenically, D. alkanexedens had a higher instantaneous corrosion rate and produced more pits in carbon steel coupons than when the same organism was grown in syntrophic co-culture with the methanogen. Since anaerobic hydrocarbon biodegradation pathways converge on fatty acid intermediates, the corrosive ability of a known fatty acid-oxidizing syntrophic bacterium, Syntrophus aciditrophicus was compared when grown in pure culture or in co-culture with a H2-utilizing sulfate-reducing bacterium (Desulfovibrio sp., strain G11) or a methanogen (M. hungatei). The instantaneous corrosion rates in the cultures were not substantially different, but the syntrophic, sulfate-reducing co-culture produced more pits in coupons than other combinations of microorganisms. Lactate-grown cultures of strain G11 had higher instantaneous corrosion rates and coupon pitting compared to the same organism cultured with hydrogen as an electron donor. Thus, if sulfate is available as an electron acceptor, the same microbial assemblages produce sulfide and low molecular weight organic acids that exacerbated biocorrosion. Despite these trends, a surprisingly high degree of variation was encountered with the corrosion assessments. Differences in biomass, initial substrate concentration, rates of microbial activity or the degree of end product formation did not account for the variations. We are forced to ascribe such differences to the metallurgical properties of the coupons.

  2. Anaerobic hydrocarbon and fatty acid metabolism by syntrophic bacteria and their impact on carbon steel corrosion

    Directory of Open Access Journals (Sweden)

    Christopher Neil Lyles

    2014-04-01

    Full Text Available The microbial metabolism of hydrocarbons is increasingly associated with the corrosion of carbon steel in sulfate-rich marine waters. However, how such transformations influence metal biocorrosion in the absence of an electron acceptor is not fully recognized. We grew a marine alkane-utilizing, sulfate-reducing bacterium, Desulfoglaeba alkanexedens, with either sulfate or Methanospirillum hungatei as electron acceptors, and tested the ability of the cultures to catalyze metal corrosion. Axenically, D. alkanexedens had a higher instantaneous corrosion rate and produced more pits in carbon steel coupons than when the same organism was grown in syntrophic co-culture with the methanogen. Since anaerobic hydrocarbon biodegradation pathways converge on fatty acid intermediates, the corrosive ability of a known fatty acid-oxidizing syntrophic bacterium, Syntrophus aciditrophicus was compared when grown in pure culture or in co-culture with a H2-utilizing sulfate-reducing bacterium (Desulfovibrio sp., strain G11 or a methanogen (M. hungatei. The instantaneous corrosion rates in the cultures were not substantially different, but the syntrophic, sulfate-reducing co-culture produced more pits in coupons than other combinations of microorganisms. Lactate-grown cultures of strain G11 had higher instantaneous corrosion rates and coupon pitting compared to the same organism cultured with hydrogen as an electron donor. Thus, if sulfate is available as an electron acceptor, the same microbial assemblages produce sulfide and low molecular weight organic acids that exacerbated biocorrosion. Despite these trends, a surprisingly high degree of variation was encountered with the corrosion assessments. Differences in biomass, initial substrate concentration, rates of microbial activity or the degree of end product formation did not account for the variations. We are forced to ascribe such differences to the metallurgical properties of the coupons.

  3. Evaporation and weather

    NARCIS (Netherlands)

    Bruin, H.A.R. de; Feddes, R.A.; Holtslag, A.A.M.; Lablans, W.N.; Schuurmans, C.J.E.; Shuttleworth, W.J.

    1987-01-01

    Data on evaporation to be used in agriculture, hydrology, forestry, etc. are usually supplied by meteorologists. Meteorologists themselves also use evaporation data. Air mass properties determining weather are strongly dependent on the input of water vapour from the surface. So for weather

  4. Designing a Weather Station

    Science.gov (United States)

    Roman, Harry T.

    2012-01-01

    The collection and analysis of weather data is crucial to the location of alternate energy systems like solar and wind. This article presents a design challenge that gives students a chance to design a weather station to collect data in advance of a large wind turbine installation. Data analysis is a crucial part of any science or engineering…

  5. Evaporation and weather

    NARCIS (Netherlands)

    Bruin, H.A.R. de; Feddes, R.A.; Holtslag, A.A.M.; Lablans, W.N.; Schuurmans, C.J.E.; Shuttleworth, W.J.

    1987-01-01

    Data on evaporation to be used in agriculture, hydrology, forestry, etc. are usually supplied by meteorologists. Meteorologists themselves also use evaporation data. Air mass properties determining weather are strongly dependent on the input of water vapour from the surface. So for weather predictio

  6. Weather and road capacity

    DEFF Research Database (Denmark)

    Jensen, Thomas Christian

    2014-01-01

    The paper presents estimations of the effect of bad weather on the observed speed on a Danish highway section; Køge Bugt Motorvejen. The paper concludes that weather, primarily precipitation and snow, has a clear negative effect on speed when the road is not in hypercongestion mode. Furthermore......, the capacity of the highway seems to be reduced in bad weather and there are indications that travel time variability is also increased, at least in free-flow conditions. Heavy precipitation reduces speed and capacity by around 5-8%, whereas snow primarily reduces capacity. Other weather variables......-parametrically against traffic density and in step 2 the residuals from step 1 are regressed linearly against the weather variables. The choice of a non-parametric method is made to avoid constricting ties from a parametric specification and because the focus here is not on the relationship between traffic flow...

  7. Weather in Mountainous Terrain (Overcoming Scientific Barriers to Weather Support)

    Science.gov (United States)

    2011-02-15

    Weather in Mountainous Terrain (Overcoming Scientific Barriers to Weather Support) Fiesta Resort & Conference Center Tempe, AZ February 1...Meteorology Overcoming Scientific Barriers to Weather Support Fiesta Resort & Conference Center Tempe, AZ February 1 & 2, 2010 Hosted by University

  8. Corrosion inhibitor mechanisms on reinforcing steel in Portland cement pastes

    Science.gov (United States)

    Martin, Farrel James

    2001-07-01

    The mechanisms of corrosion inhibitor interaction with reinforcing steel are investigated in the present work, with particular emphasis on effects associated with corrosion inhibitors admixed into Portland cement paste. The principal objective in reinforcing steel corrosion inhibition for Portland cement concrete is observed to be preservation of the naturally passive steel surface condition established by the alkaline environment. Introduction of chloride ions to the steel surface accelerates damage to the passive film. Excessive damage to the passive film leads to loss of passivity and a destabilization of conditions that facilitate repair of the passive film. Passive film preservation in presence of chloride ions is achieved either through stabilization of the passive film or by modification of the chemical environment near the steel surface. Availability of inhibitors to the steel surface and their tendency to stabilize passive film defects are observed to be of critical importance. Availability of admixed corrosion inhibitors to the passive film is affected by binding of inhibitors during cement paste hydration. It is determined that pore solution concentrations of inorganic admixed inhibitors tend to be lower than the admixed concentration, while pore solution concentrations of organic admixed inhibitors tend to be higher than the admixed concentration. A fundamental difference of inhibitor function is observed between film-forming and defect stabilizing corrosion inhibitors. Experiments are conducted using coupons of reinforcing steel that are exposed to environments simulating chloride-contaminated Portland cement concrete. A study of the steel/cement paste interface is also performed, and compounds forming at this interface are identified using X-Ray diffraction.

  9. Mineralogical Transformation and Electrochemical Nature of Magnesium-Rich Primers during Natural Weathering

    Directory of Open Access Journals (Sweden)

    Shashi S. Pathak

    2014-07-01

    Full Text Available Magnesium-rich primers (MgRP have generated great interest as a promising alternative to chromium-based primers for the protection of aluminum substrates but their performance during exterior exposure has not been well documented. This paper focuses on the evaluation of MgRP during natural weathering to gain insight into its mineralogical phase transformation and electrochemical nature. Control studies were conducted on Mg and AA2024-T3 coupons. The results indicate that Mg particles in MgRP transform into a variety of hydroxide, carbonate, and hydroxy carbonates. During natural weathering, CO2 inhibited the dissolution of both Mg and AA2024-T3 as a result of protective carbonate layer formation in the coating.

  10. 浅谈地票交易二级市场构建问题%Brief Discussion about Construction of Secondary Trading Market of Land Coupon

    Institute of Scientific and Technical Information of China (English)

    覃琳; 胡渝清; 叶涛

    2014-01-01

    This paper made clear the thinking of constructing secondary land coupon trading market, and set that constructing secondary land coupon trading market should firstly pinpoint such market factors as market main players, objects, trading venues, trading manner, trading process and rule.Based on this, the article analyzed the opening procedure of secondary land coupon trading market, and finally designed the supervision mechanism of the market, in order to ensure the smooth and healthy operation of secondary land coupon trading market.%明确了构建地票交易二级市场的思路,设定了构建地票交易二级市场应首先明确市场主体、客体、交易场所、交易方式、交易流程及规则等市场要素,并在此基础上分析了地票交易二级市场的开放步骤,最后对市场的监管机制进行了设计,以确保地票交易二级市场的平稳、健康运行。

  11. A new coupon design for simultaneous analysis of in situ microbial biofilm formation and community structure in drinking water distribution systems.

    Science.gov (United States)

    Deines, Peter; Sekar, Raju; Husband, P Stewart; Boxall, Joby B; Osborn, A Mark; Biggs, Catherine A

    2010-06-01

    This study presents a new coupon sampling device that can be inserted directly into the pipes within water distribution systems (WDS), maintaining representative near wall pipe flow conditions and enabling simultaneous microscopy and DNA-based analysis of biofilms formed in situ. To evaluate this sampling device, fluorescent in situ hybridization (FISH) and denaturing gradient gel electrophoresis (DGGE) analyses were used to investigate changes in biofilms on replicate coupons within a non-sterile pilot-scale WDS. FISH analysis demonstrated increases in bacterial biofilm coverage of the coupon surface over time, while the DGGE analysis showed the development of increasingly complex biofilm communities, with time-specific clustering of these communities. This coupon design offers improvements over existing biofilm sampling devices in that it enables simultaneous quantitative and qualitative compositional characterization of biofilm assemblages formed within a WDS, while importantly maintaining fully representative near wall pipe flow conditions. Hence, it provides a practical approach that can be used to capture the interactions between biofilm formation and changing abiotic conditions, boundary shear stress, and turbulent driven exchange within WDS.

  12. New steel-materials for bridge-construction; Kyoryo yoto no shinkozai oyobi shinkenzai

    Energy Technology Data Exchange (ETDEWEB)

    Sakata, Y.; Fujii, Y.; Suzuki, A.; Takagi, M.; Nishiumi, K.; Kusunoki, T.; Tsuzuki, T.; Usami, A. [Nippon Steel Corp., Tokyo (Japan)

    1998-07-31

    Nippon Steel Corporation is exerting endeavors for the development of various technologies which concern materials, designing, and execution in the field of bridges. Outlined in this report are the merits and effects of some fruits of such endeavors, which involve a new weather-resistant steel to reduce the maintenance cost, longitudinally profiled steel plates to reduce the manufacturing cost, rectangular steel tubes using a high-tenacity steel, long-span-conscious grating slabs and steel elements to save labor in bridge construction, etc. For instance, the newly developed weather-resistant steel is a product intended for use for Japan`s big cities and trunk lines near the seashore, and is so designed as to contain 5% Ni to withstand seashore climate after studies and tests. This steel will contribute to the reduction in the cost for maintaining bridges in seashore belts where the conventional weather-resistant steel does not work effectively or in snowy regions where the use of snow-melting agents is inevitable. In another example, the steel is used for the construction of Nippon Steel Corporation`s Minami-Ohashi Bridge situated in the sea-facing zone of Nagoya Works of the corporation, where tests are still under way. 18 refs., 23 figs., 4 tabs.

  13. Lethality of chlorine, chlorine dioxide, and a commercial produce sanitizer to Bacillus cereus and Pseudomonas in a liquid detergent, on stainless steel, and in biofilm.

    Science.gov (United States)

    Kreske, Audrey C; Ryu, Jee-Hoon; Pettigrew, Charles A; Beuchat, Larry R

    2006-11-01

    Many factors that are not fully understood may influence the effectiveness of sanitizer treatments for eliminating pathogens and spoilage microorganisms in food or detergent residues or in biofilms on food contact surfaces. This study was done to determine the sensitivities of Pseudomonas cells and Bacillus cereus cells and spores suspended in a liquid dishwashing detergent and inoculated onto the surface of stainless steel to treatment with chlorine, chlorine dioxide, and a commercial produce sanitizer (Fit). Cells and spores were incubated in a liquid dishwashing detergent for 16 to 18 h before treatment with sanitizers. At 50 microg/ml, chlorine dioxide killed a significantly higher number of Pseudomonas cells (3.82 log CFU/ml) than did chlorine (a reduction of 1.34 log CFU/ml). Stainless steel coupons were spot inoculated with Pseudomonas cells and B. cereus cells and spores, with water and 5% horse serum as carriers. Chlorine was more effective than chlorine dioxide in killing cells and spores of B. cereus suspended in horse serum. B. cereus biofilm on stainless steel coupons that were treated with chlorine dioxide or chlorine at 200 microg/ml had total population reductions (vegetative cells plus spores) of > or = 4.42 log CFU per coupon; the number of spores was reduced by > or = 3.80 log CFU per coupon. Fit (0.5%) was ineffective for killing spot-inoculated B. cereus and B. cereus in biofilm, but treatment with mixtures of Fit and chlorine dioxide caused greater reductions than did treatment with chlorine dioxide alone. In contrast, when chlorine was combined with Fit, the lethality of chlorine was completely lost. This study provides information on the survival and sanitizer sensitivity of Pseudomonas and B. cereus in a liquid dishwashing detergent, on the surface of stainless steel, and in a biofilm. This information will be useful for developing more effective strategies for cleaning and sanitizing contact surfaces in food preparation and processing

  14. In-service testing of Ni{sub 3}Al coupons and trays in carburizing furnaces at Delphi Saginaw. CRADA final report

    Energy Technology Data Exchange (ETDEWEB)

    Sikka, V.K.; Santella, M.L.; Viswanathan, S.; Swindeman, R.W. [Oak Ridge National Lab., TN (United States); Chatterjee, M. [General Motors Corporaion, Saginaw Division (United States)

    1998-08-01

    This Cooperative Research and Development Agreement (CRADA) report deals with the development of nickel aluminide alloy for improved longer life heat-resistant fixture assemblies for batch and continuous pusher carburizing furnaces. The nickel aluminide development was compared in both coupon and component testing with the currently used Fe-Ni-Cr heat-resisting alloy known as HU. The specific goals of the CRADA were: (1) casting process development, (2) characterization and possible modification of the alloy composition to optimize its manufacturing ability and performance under typical furnace operating conditions, and (3) testing and evaluation of specimens and prototype fixtures. In support of the CRADA objectives, coupons of nickel aluminide and the HU alloy were installed in both batch and pusher furnaces. The coupons were taken from two silicon levels and contained welds made with two different filler compositions (IC-221LA and IC-221W). Both nickel-aluminide and HU coupons were removed from the batch and pusher carburizing furnace at time intervals ranging from one month to one year. The exposed coupons were cut and mounted for metallographic, hardness, and microprobe analysis. The results of the microstructural analysis have been transmitted to General Motors Corporation, Saginaw Division (Delphi Saginaw) through reports that were presented at periodic CRADA review meetings. Based on coupon testing and verification of the coupon results with the testing of trays, Delphi Saginaw moved forward with the use of six additional trays in a batch furnace and two assemblies in a pusher furnace. Fifty percent of the trays and fixtures are in the as-cast condition and the remaining trays and fixtures are in the preoxidized condition. The successful operating experience of two assemblies in the pusher furnace for nearly a year formed the basis for a production run of 63 more assemblies. The production run required melting of 94 heats weighing 500 lb. each. Twenty

  15. Oil Rig Weather Observations

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Weather observations taken at offshore platforms along the United States coastlines. The majority are located in oil-rich areas of the Gulf of Mexico, Gulf of...

  16. Uruguay - Surface Weather Observations

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Surface weather observation forms for 26 stations in Uruguay. Period of record 1896-2005, with two to eight observations per day. Files created through a...

  17. Cape Kennedy Weather Data

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Digitized data taken from original weather observations taken at Cape Kennedy Air Force Station, Florida. Elements recorded are wind speed and direction,...

  18. Monthly Weather Observations

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Surface Weather Observation 1001 Forms is a set of historical manuscript records for the period 1893-1948. The collection includes two very similar form types: Form...

  19. Daily Weather Maps

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Several different government offices have published the Daily weather maps over its history. The publication has also gone by different names over time. The U.S....

  20. Weather Information Processing

    Science.gov (United States)

    1991-01-01

    Science Communications International (SCI), formerly General Science Corporation, has developed several commercial products based upon experience acquired as a NASA Contractor. Among them are METPRO, a meteorological data acquisition and processing system, which has been widely used, RISKPRO, an environmental assessment system, and MAPPRO, a geographic information system. METPRO software is used to collect weather data from satellites, ground-based observation systems and radio weather broadcasts to generate weather maps, enabling potential disaster areas to receive advance warning. GSC's initial work for NASA Goddard Space Flight Center resulted in METPAK, a weather satellite data analysis system. METPAK led to the commercial METPRO system. The company also provides data to other government agencies, U.S. embassies and foreign countries.

  1. Space Weather Products

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Collection includes a variety of space weather datasets from the National Oceanic and Atmospheric Administration and from the World Data Service for Geophysics,...

  2. Genetically optimizing weather predictions

    Science.gov (United States)

    Potter, S. B.; Staats, Kai; Romero-Colmenero, Encarni

    2016-07-01

    humidity, air pressure, wind speed and wind direction) into a database. Built upon this database, we have developed a remarkably simple approach to derive a functional weather predictor. The aim is provide up to the minute local weather predictions in order to e.g. prepare dome environment conditions ready for night time operations or plan, prioritize and update weather dependent observing queues. In order to predict the weather for the next 24 hours, we take the current live weather readings and search the entire archive for similar conditions. Predictions are made against an averaged, subsequent 24 hours of the closest matches for the current readings. We use an Evolutionary Algorithm to optimize our formula through weighted parameters. The accuracy of the predictor is routinely tested and tuned against the full, updated archive to account for seasonal trends and total, climate shifts. The live (updated every 5 minutes) SALT weather predictor can be viewed here: http://www.saao.ac.za/ sbp/suthweather_predict.html

  3. Cockpit weather information system

    Science.gov (United States)

    Tu, Jeffrey Chen-Yu (Inventor)

    2000-01-01

    Weather information, periodically collected from throughout a global region, is periodically assimilated and compiled at a central source and sent via a high speed data link to a satellite communication service, such as COMSAT. That communication service converts the compiled weather information to GSDB format, and transmits the GSDB encoded information to an orbiting broadcast satellite, INMARSAT, transmitting the information at a data rate of no less than 10.5 kilobits per second. The INMARSAT satellite receives that data over its P-channel and rebroadcasts the GDSB encoded weather information, in the microwave L-band, throughout the global region at a rate of no less than 10.5 KB/S. The transmission is received aboard an aircraft by means of an onboard SATCOM receiver and the output is furnished to a weather information processor. A touch sensitive liquid crystal panel display allows the pilot to select the weather function by touching a predefined icon overlain on the display's surface and in response a color graphic display of the weather is displayed for the pilot.

  4. The role of acetogens in microbial influenced corrosion of steel

    Directory of Open Access Journals (Sweden)

    Jaspreet eMand

    2014-06-01

    Full Text Available Microbially-influenced corrosion (MIC of iron (Fe0 by sulfate reducing bacteria (SRB has been studied extensively. Through a mechanism, that is still poorly understood, electrons or hydrogen (H2 molecules are removed from the metal surface and used as electron donor for sulfate reduction. The resulting ferrous ions precipitate in part with the sulfide produced, forming characteristic black iron sulfide. Hydrogenotrophic methanogens can also contribute to MIC. Incubation of pipeline water samples, containing bicarbonate and some sulfate, in serum bottles with steel coupons and a headspace of 10% (vol/vol CO2 and 90% N2, indicated formation of acetate and methane. Incubation of these samples in serum bottles, containing medium with coupons and bicarbonate but no sulfate, also indicated that formation of acetate preceded the formation of methane. Microbial community analyses of these enrichments indicated the presence of Acetobacterium, as well we of hydrogenotrophic and acetotrophic methanogens. The formation of acetate by homoacetogens, such as Acetobacterium woodii from H2 (or Fe0 and CO2, is potentially important, because acetate is a required carbon source for many SRB growing with H2 and sulfate. A consortium of the SRB Desulfovibrio vulgaris Hildenborough and A. woodii was able to grow in defined medium with H2, CO2 and sulfate, because A. woodii provides the acetate, needed by D. vulgaris under these conditions. Likewise, general corrosion rates of metal coupons incubated with D. vulgaris in the presence of acetate or in the presence of A. woodii were higher than in the absence of acetate or A. woodii, respectively. An extended MIC model capturing these results is presented.

  5. High Nitrogen Stainless Steel

    Science.gov (United States)

    2011-07-19

    Kiev, 1993. 7. High Nitrogen Steels, edited by M. Kikuchi and Y. Mishima , Vol. 36, No. 7, Iron and Steel Institute of Japan Inernational, Tokyo...the Corrosion of Iron and Steels,” High Nitrogen Steels, edited by M. Kikuchi and Y. Mishima , Vol. 36, No. 7, Iron and Steel Institute of Japan

  6. Anticorrosive Influence of Acetobacter aceti Biofilms on Carbon Steel

    Science.gov (United States)

    France, Danielle Cook

    2016-09-01

    Microbiologically influenced corrosion (MIC) of carbon steel infrastructure is an emerging environmental and cost issue for the ethanol fuel industry, yet its examination lacks rigorous quantification of microbiological parameters that could reveal effective intervention strategies. To quantitatively characterize the effect of cell concentration on MIC of carbon steel, numbers of bacteria exposed to test coupons were systematically controlled to span four orders of magnitude throughout a seven-day test. The bacterium studied, Acetobacter aceti, has been found in ethanol fuel environments and can convert ethanol to the corrosive species acetic acid. A. aceti biofilms formed during the test were qualitatively evaluated with fluorescence microscopy, and steel surfaces were characterized by scanning electron microscopy. During exposure, biofilms developed more quickly, and test reactor pH decreased at a faster rate, when cell exposure was higher. Resulting corrosion rates, however, were inversely proportional to cell exposure, indicating that A. aceti biofilms are able to protect carbon steel surfaces from corrosion. This is a novel demonstration of corrosion inhibition by an acid-producing bacterium that occurs naturally in corrosive environments. Mitigation techniques for MIC that harness the power of microbial communities have the potential to be scalable, inexpensive, and green solutions to industrial problems.

  7. Study of yttrium 4-nitrocinnamate to promote surface interactions with AS1020 steel

    Science.gov (United States)

    Hien, P. V.; Vu, N. S. H.; Thu, V. T. H.; Somers, A.; Nam, N. D.

    2017-08-01

    Yttrium 4-nitrocinnamate (Y(4-NO2Cin)3) was added to an aqueous chloride solution and studied as a possible corrosion inhibition system. Electrochemical techniques and surface analysis have been powerful tools to better understand the corrosion and inhibition processes of mild steel in 0.01 M NaCl solution. A combination of scanning electron microscopy (SEM), atomic force microscopy (AFM), attenuated total reflectance Fourier transform infrared spectroscopy (ATR-FTIR), X-ray photoelectron spectroscopy (XPS), Potentiodynamic polarization (PD), electrochemical impedance spectroscopy (EIS) and wire beam electrode (WBE) techniques was found to be useful in the characterization of this system. The result indicated that Y(4-NO2Cin)3 is able to effectively inhibit corrosion at a low concentration of 0.45 mM. Surface analysis clearly shows that the surface of steel coupons exposed to Y(4-NO2Cin)3 solution remained uniform and smooth, whereas the surface of steel coupons exposed to solution without inhibitor addition was severely corroded. The results suggest that Y(4-NO2Cin)3 behaves as a mixed inhibitor and mitigates corrosion by promoting random distribution of minor anodes. These are attributed to the formation of metal species bonding to the 4-nitrocinnamate component and hydrolysis of the Y(4-NO2Cin)3 to form oxide/hydroxides as a protective film layer.

  8. Failure of Stainless Steel Welds Due to Microstructural Damage Prevented by In Situ Metallography

    Directory of Open Access Journals (Sweden)

    Juan Manuel Salgado Lopez

    Full Text Available Abstract In stainless steels, microstructural damage is caused by precipitation of chromium carbides or sigma phase. These microconstituents are detrimental in stainless steel welds because they lead to weld decay. Nevertheless, they are prone to appear in the heat affected zone (HAZ microstructure of stainless steel welds. This is particularly important for repairs of industrial components made of austenitic stainless steel. Non-destructive metallography can be applied in welding repairs of AISI 304 stainless steel components where it is difficult to ensure that no detrimental phase is present in the HAZ microstructure. The need of microstructural inspection in repairs of AISI 304 is caused because it is not possible to manufacture coupons for destructive metallography, with which the microstructure can be analyzed. In this work, it is proposed to apply in situ metallography as non-destructive testing in order to identify microstructural damage in the microstructure of AISI 304 stainless steel welds. The results of this study showed that the external surface micrographs of the weldment are representative of HAZ microstructure of the stainless steel component; because they show the presence of precipitated metallic carbides in the grain boundaries or sigma phase in the microstructure of the HAZ.

  9. Desiccation of adhering and biofilm Listeria monocytogenes on stainless steel: Survival and transfer to salmon products

    DEFF Research Database (Denmark)

    Hansen, Lisbeth Truelstrup; Vogel, Birte Fonnesbech

    2011-01-01

    The foodborne bacterial pathogen, Listeria monocytogenes, commonly contaminates foods during processing, where the microorganisms are potentially subjected to low relative humidity (RH) conditions for extended periods of time. The objective of this study was to examine survival during desiccation...... (43% RH and 15°C) of biofilm L. monocytogenes N53-1 cells on stainless steel coupons and to assess subsequent transfer to salmon products. Formation of static biofilm (2days at 100% RH and 15°C) prior to desiccation for 23days significantly (P...

  10. Surface modification of stainless steel by grafting of poly(ethylene glycol) for reduction in protein adsorption.

    Science.gov (United States)

    Zhang, F; Kang, E T; Neoh, K G; Wang, P; Tan, K L

    2001-06-01

    The surface of stainless steel was first modified by the silane coupling agent (SCA), (3-mercaptopropyl)trimethoxysilane. The silanized stainless-steel surface (SCA-SS surface) was subsequently activated by argon plasma and then subjected to UV-induced graft polymerization of poly(ethylene glycol)methacrylate (PEGMA). The chemical structures and composition of the pristine, silane-treated, plasma-treated and PEGMA graft-polymerized stainless-steel coupon surfaces were characterized by X-ray photoelectron spectroscopy (XPS) and attenuated total reflection-Fourier transform infrared (ATR-FTIR) spectroscopy. The graft polymerization of PEGMA onto the plasma-pretreated SCA-SS surface was studied with different argon plasma pretreatment time, macromonomer concentration, and UV graft polymerization time. In general, a brief plasma pretreatment, high PEGMA concentration, and long UV graft polymerization time readily resulted in a high graft concentration. The PEGMA graft-polymerized stainless-steel coupon (PEGMA-g-SCA-SS) with a high graft concentration, and thus a high PEG content, was found to be very effective in preventing bovine serum albumin and gamma-globulin adsorption.

  11. Sour and sweet corrosion of carbon steel : general or pitting or localized or all of the above?

    Energy Technology Data Exchange (ETDEWEB)

    Papavinasam, S.; Doiron, A.; Li, J.; Park, D.Y.; Liu, P. [Natural Resources Canada, Ottawa, ON (Canada). CANMET Materials Technology Laboratory

    2009-07-01

    Carbon steel is used for 80 per cent of all refinery components in refineries, petrochemical plants and oil and gas pipelines. This paper described a model designed to predict internal pitting corrosion of carbon steel in sour and sweet environments. The effects of temperature and partial pressure of carbon dioxide (CO{sub 2}) were investigated experimentally using scanning electron microscopy (SEM) and laser profilometer analyses. Eight carbon steel coupons were placed in a high temperature high pressure rotating cage system. An autoclave was charged with CO{sub 2} and methane. Coupons were then examined using SEM and energy dispersive spectroscopy (EDS). Pit depth and density were evaluated. The obtained data were then filtered using a Gaussian filter to minimize scattering. The study showed that mass loss increased almost linearly as a function of CO{sub 2} partial pressure. An analysis of the surface layers indicated that a compact layer did not form to protect the surface from corrosion. Classical pitting corrosion processes were discussed, and the characteristics of carbon steel corrosion were outlined. 23 refs., 2 tabs., 12 figs.

  12. Space weather & telecommunications

    CERN Document Server

    Goodman, John M

    2006-01-01

    This book is both a survey of practical concepts for forecasting the performance of various telecommunication systems as well as a balanced treatment of space-weather phenomena that give rise to telecommunication impairment episodes. It bridges the gap in the relationship that exists between the following two disciplines: space weather and telecommunication system performance. There are a number of books that address one of the two disciplines in some detail, but only merely mention the other as an afterthought. In this book the author has married the two disciplines so that the readership can

  13. Fatigue damage observed non-destructively in fibre composite coupon test specimens by X-ray CT

    Science.gov (United States)

    Jespersen, K. M.; Mikkelsen, L. P.

    2016-07-01

    This study presents a method for monitoring the 3D fatigue damage progression on a micro-structural level in a glass fibre/polymer coupon test specimen by means of laboratory X-ray Computed Tomography (CT). A modified mount and holder made for the standard test samples to fit into the X-ray CT scanner along with a tension clamp solution is presented. Initially, the same location of the test specimen is inspected by ex-situ X-ray CT during the fatigue loading history, which shows the damage progression on a micro-structural level. The openings of individual uni-directional (UD) fibre fractures are seen to generally increase with the number of cycles, and new regions of UD fibre fractures also appear. There are some UD fibre fractures that are difficult to detect since their opening is small. Therefore, the effect of tension on the crack visibility is examined afterwards using a tension clamp solution. With applied tension some additional cracks become visible and the openings of fibre fractures increases, which shows the importance of applied tension during the scan.

  14. Role of beta 1-4 linked polymers in the biofilm structure of marine Pseudomonas sp. CE-2 on 304 stainless steel coupons

    Digital Repository Service at National Institute of Oceanography (India)

    Jain, A.; Bhosle, N.B.

    and contributes to biofilm architecture and stress tolerance under water-limiting conditions. J Bacteriol 189: 8290-8299. Danese PN, Pratt LA and Kolter R. 2000. Exopolysaccharide production is required for development of Escherichia coli K-12 biofilm... architecture. J Bacteriol 182 (12): 3593- 3596. Dubois M. 1956. Colorimetric method for determination of sugars and related substances. Anal Chem 28: 350–356. Darby C, Hsu JW, Ghori N, Falkow S. 2002. Caenorhabditis elegans: plague biofilm block food...

  15. A comparison of models for measurable deterioration: an application to coating on steel structures

    NARCIS (Netherlands)

    R.P. Nicolai (Robin); R. Dekker (Rommert); J.M. van Noortwijk (Jan)

    2006-01-01

    textabstractSteel structures like bridges, tanks and pylons are exposed to outdoor weathering conditions. In order to prevent them from corrosion they are protected by organic coating systems. This paper focuses on modelling the deterioration of the organic coating layer that protects steel structur

  16. Dress for the Weather

    Science.gov (United States)

    Glen, Nicole J.; Smetana, Lara K.

    2010-01-01

    "If someone were traveling to our area for the first time during this time of year, what would you tell them to bring to wear? Why?" This question was used to engage students in a guided-inquiry unit about how climate differs from weather. In this lesson, students explored local and national data sets to give "travelers" advice…

  17. Microbial Weathering of Olivine

    Science.gov (United States)

    McKay, D. S.; Longazo, T. G.; Wentworth, S. J.; Southam, G.

    2002-01-01

    Controlled microbial weathering of olivine experiments displays a unique style of nanoetching caused by biofilm attachment to mineral surfaces. We are investigating whether the morphology of biotic nanoetching can be used as a biosignature. Additional information is contained in the original extended abstract.

  18. Winter Weather: Indoor Safety

    Science.gov (United States)

    ... Part 3 of 3) Hot Weather Tips Heat Stress in Older Adults FAQs Extreme Heat PSAs Related Links MMWR Bibliography CDC's Program Floods Flood Readiness Personal Hygiene After a Disaster Cleanup of Flood Water After a Flood Worker Safety Educational Materials Floods ...

  19. Winter Weather: Frostbite

    Science.gov (United States)

    ... Part 3 of 3) Hot Weather Tips Heat Stress in Older Adults FAQs Extreme Heat PSAs Related Links MMWR Bibliography CDC's Program Floods Flood Readiness Personal Hygiene After a Disaster Cleanup of Flood Water After a Flood Worker Safety Educational Materials Floods ...

  20. Winter Weather Checklists

    Science.gov (United States)

    ... Part 3 of 3) Hot Weather Tips Heat Stress in Older Adults FAQs Extreme Heat PSAs Related Links MMWR Bibliography CDC's Program Floods Flood Readiness Personal Hygiene After a Disaster Cleanup of Flood Water After a Flood Worker Safety Educational Materials Floods ...

  1. Weather at LANL

    Energy Technology Data Exchange (ETDEWEB)

    Bruggeman, David Alan [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2016-04-19

    This report gives general information about how to become a meteorologist and what kinds of jobs exist in that field. Then it goes into detail about why weather is monitored at LANL, how it is done, and where the data can be accessed online.

  2. Cold Weather Pet Safety

    Science.gov (United States)

    ... they can be knocked over, potentially starting a fire. Check your furnace before the cold weather sets in to make ... avoided because of the risk of burns or fire. Heated pet mats should also be used ... to burrow, get them back inside quickly because they are showing signs of ...

  3. Dress for the Weather

    Science.gov (United States)

    Glen, Nicole J.; Smetana, Lara K.

    2010-01-01

    "If someone were traveling to our area for the first time during this time of year, what would you tell them to bring to wear? Why?" This question was used to engage students in a guided-inquiry unit about how climate differs from weather. In this lesson, students explored local and national data sets to give "travelers" advice…

  4. 'Is it the weather?'

    NARCIS (Netherlands)

    B. Jacobsen (Ben); W.A. Marquering (Wessel)

    2004-01-01

    textabstractWe show that results in the recent strand of the literature that tries to explain stock returns by weather induced mood shifts of investors might be data-driven inference. More specifically, we consider two recent studies (Kamstra, Kramer and Levi, 2003a and Cao and Wei, 2004) that claim

  5. Elasto-Plastic 3D Finite Element Contact Analysis of a Hole Containing a Circular Insert in a Fatigue Test Coupon

    Science.gov (United States)

    2015-08-01

    Aeronautical Research Laboratory, Defence Science and Technology Organisation , Department of Defence, Australia, January 1988. 5. D Duprat, D Campassens...Containing a Circular Insert in a Fatigue Test Coupon Witold Waldman AUSTRALIA DEFENCE ORGANISATION No. of Copies Task Sponsor OIC-ASI-DGTA...UNCLASSIFIED DEFENCE SCIENCE AND TECHNOLOGY GROUP DOCUMENT CONTROL DATA 1. DLM/CAVEAT (OF DOCUMENT) 2. TITLE Elasto–Plastic 3D Finite Element

  6. Linear-Elastic 2D and 3D Finite Element Contact Analysis of a Hole Containing a Circular Insert in a Fatigue Test Coupon

    Science.gov (United States)

    2015-07-01

    UNCLASSIFIED UNCLASSIFIED Linear-Elastic 2D and 3D Finite Element Contact Analysis of a Hole Containing a Circular Insert in a Fatigue Test...circular hole in an aluminium plate fitted with a titanium fastener that were computed using two-dimensional finite element contact analysis . By...UNCLASSIFIED Linear-Elastic 2D and 3D Finite Element Contact Analysis of a Hole Containing a Circular Insert in a Fatigue Test Coupon

  7. Weatherization Works: An interim report of the National Weatherization Evaluation

    Energy Technology Data Exchange (ETDEWEB)

    Brown, M.A.; Berry, L.G. [Oak Ridge National Lab., TN (United States); Kinney, L.F. [Synertech Systems Corp., Syracuse, NY (United States)

    1993-11-01

    The National Weatherization Evaluation is the first comprehensive evaluation of the Weatherization Assistance Program since 1984. The evaluation was designed to accomplish the following goals: Estimate energy savings and cost effectiveness; Assess nonenergy impacts; Describe the weatherization network; Characterize the eligible population and resources; and Identify factors influencing outcomes and opportunities for the future. As a national program, weatherization incorporates considerable diversity due to regional differences. Therefore, evaluation results are presented both in aggregate and for three climate regions: cold, moderate and hot.

  8. Weatherization Works: An interim report of the National Weatherization Evaluation

    Energy Technology Data Exchange (ETDEWEB)

    Brown, M.A.; Berry, L.G. [Oak Ridge National Lab., TN (United States); Kinney, L.F. [Synertech Systems Corp., Syracuse, NY (United States)

    1993-11-01

    The National Weatherization Evaluation is the first comprehensive evaluation of the Weatherization Assistance Program since 1984. The evaluation was designed to accomplish the following goals: Estimate energy savings and cost effectiveness; Assess nonenergy impacts; Describe the weatherization network; Characterize the eligible population and resources; and Identify factors influencing outcomes and opportunities for the future. As a national program, weatherization incorporates considerable diversity due to regional differences. Therefore, evaluation results are presented both in aggregate and for three climate regions: cold, moderate and hot.

  9. Market challenges for steel

    Energy Technology Data Exchange (ETDEWEB)

    Lauprecht, W.E.; Bulla, W.

    1981-11-01

    Country-wise division of generation of high-alloyed steels, stainless steel and alloyed steel in Western Europe/the Western World. Review of expanding markets for alloyed steels on sectors like-oil field pipes, offshore structure gas- and oil transport in pipelines, coal conversion, nuclear energy, condenser tubes, solar energy, car industry, environmental protection and chemistry.

  10. North America Synoptic Weather Maps

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Series of Synoptic Weather Maps. Maps contains a surface analysis comprised of plotted weather station observations, isobars indicating low and high-pressure...

  11. Severe Weather Data Inventory (SWDI)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — The Severe Weather Data Inventory (SWDI) is an integrated database of severe weather records for the United States. SWDI enables a user to search through a variety...

  12. Peeking under the Iron Curtain: Development of a Microcosm for Imaging the Colonization of Steel Surfaces by Mariprofundus sp. Strain DIS-1, an Oxygen-Tolerant Fe-Oxidizing Bacterium.

    Science.gov (United States)

    Mumford, Adam C; Adaktylou, Irini J; Emerson, David

    2016-11-15

    Microbially influenced corrosion (MIC) is a major cause of damage to steel infrastructure in the marine environment. Despite their ability to grow directly on Fe(II) released from steel, comparatively little is known about the role played by neutrophilic iron-oxidizing bacteria (FeOB). Recent work has shown that FeOB grow readily on mild steel (1018 MS) incubated in situ or as a substrate for pure cultures in vitro; however, details of how they colonize steel surfaces are unknown yet are important for understanding their effects. In this study, we combine a novel continuously upwelling microcosm with confocal laser scanning microscopy (CLSM) to determine the degree of colonization of 1018 MS by the marine FeOB strain DIS-1. 1018 MS coupons were incubated with sterile seawater (pH 8) inoculated with strain DIS-1. Incubations were performed both under oxic conditions and in an anoxic-to-oxic gradient. Following incubations of 1 to 10 days, the slides were removed from the microcosms and stained to visualize both cells and stalk structures. Stained coupons were visualized by CLSM after being mounted in a custom frame to preserve the three-dimensional structure of the biofilm. The incubation of 1018 MS coupons with strain DIS-1 under oxic conditions resulted in initial attachment of cells within 2 days and nearly total coverage of the coupon with an ochre film within 5 days. CLSM imaging revealed a nonadherent biofilm composed primarily of the Fe-oxide stalks characteristic of strain DIS-1. When incubated with elevated concentrations of Fe(II), DIS-1 colonization of 1018 MS was inhibited.

  13. What characterizes planetary space weather?

    OpenAIRE

    2014-01-01

    International audience; Space weather has become a mature discipline for the Earth space environment. With increasing efforts in space exploration, it is becoming more and more necessary to understand the space environments of bodies other than Earth. This is the background for an emerging aspect of the space weather discipline: planetary space weather. In this article, we explore what characterizes planetary space weather, using some examples throughout the solar system. We consider energy s...

  14. Inhibition of mild steel corrosion using Jatropha Curcas leaf extract

    Directory of Open Access Journals (Sweden)

    OLORUNFEMI MICHAEL AJAYI

    2014-05-01

    Full Text Available Jatropha Curcas leaf was investigated as a green inhibitor on the degradation of mild steel in 4 M HCl and 4 M H2SO4 aqueous solutions using gasometric technique. Mild steel coupons of dimension 2 × 1.5 cm were immersed in test solutions of uninhibited acid and also those with extract concentrations of 4 ml, 6 ml, 8 ml and 10 ml at 30 oC, for up to 30 minutes. The results showed that as the concentration of the extract increases, there was reduction in the corrosion rate. As the extract concentration increased from 4 ml to 10 ml at 30 minutes exposure, the volume of hydrogen gas evolved decreased from 19.1 cm3 to 11.2 cm3 in H2SO4 medium, while it reduced to 5 cm3 from 9 cm3 in HCl medium. Also, the metal surface-phytoconstituent interaction mechanism showed that 6 minutes is the best exposure time for the adsorption of the extract in both acidic media. The Jatropha Curcas leaf extract was adsorbed on the mild steel surface to inhibit corrosion, while the experimental data obtained at 30 minutes exposure in both acidic media were well fitted with the Langmuir adsorption isotherm. Hence, Jatropha Curcas leaf extract is a good and safe inhibitor in both acidic solutions.

  15. Comparison of methods for quantitating Salmonella enterica Typhimurium and Heidelberg strain attachment to reusable plastic shipping container coupons and preliminary assessment of sanitizer efficacy.

    Science.gov (United States)

    Shi, Zhaohao; Baker, Christopher A; Lee, Sang In; Park, Si Hong; Kim, Sun Ae; Ricke, Steven C

    2016-09-01

    Salmonella serovars, one of the leading contributors to foodborne illness and are especially problematic for foods that are not cooked before consumption, such as fresh produce. The shipping containers that are used to transport and store fresh produce may play a role in cross contamination and subsequent illnesses. However, methods for quantitatively attached cells are somewhat variable. The overall goal of this study was to compare conventional plating with molecular methods for quantitating attached representative strains for Salmonella Typhimurium and Heidelberg on reusable plastic containers (RPC) coupons, respectively. We attached Salmonella enterica serovar Typhimurium ATCC 14028 and serovar Heidelberg SL486 (parent and an antibiotic resistant marker strain) to plastic coupons (2.54 cm(2)) derived from previously used shipping containers by growing for 72 h in tryptic soy broth. The impact of the concentration of sanitizer on log reductions between unsanitized and sanitized coupons was evaluated by exposing attached S. Typhimurium cells to 200 ppm and 200,000 ppm sodium hypochlorite (NaClO). Differences in sanitizer effectiveness between serovars were also evaluated with attached S. Typhimurium compared to attached S. Heidelberg populations after being exposed to 200 ppm peracetic acid (PAA). Treatment with NaClO caused an average of 2.73 ± 0.23 log CFU of S. Typhimurium per coupon removed with treatment at 200 ppm while 3.36 ± 0.54 log CFU were removed at 200,000 ppm. Treatment with PAA caused an average of 2.62 ± 0.15 log CFU removed for S. Typhimurium and 1.41 ± 0.17 log CFU for S. Heidelberg (parent) and 1.61 ± 0.08 log CFU (marker). Lastly, scanning electron microscopy (SEM) was used to visualize cell attachment and coupon surface topography. SEM images showed that remaining attached cell populations were visible even after sanitizer application. Conventional plating and qPCR yielded similar levels of enumerated bacterial populations

  16. Plasma nitriding of steels

    CERN Document Server

    Aghajani, Hossein

    2017-01-01

    This book focuses on the effect of plasma nitriding on the properties of steels. Parameters of different grades of steels are considered, such as structural and constructional steels, stainless steels and tools steels. The reader will find within the text an introduction to nitriding treatment, the basis of plasma and its roll in nitriding. The authors also address the advantages and disadvantages of plasma nitriding in comparison with other nitriding methods. .

  17. Severe Weather Planning for Schools

    Science.gov (United States)

    Watson, Barbara McNaught; Strong, Christopher; Bunting, Bill

    2008-01-01

    Flash floods, severe thunderstorms, and tornadoes occur with rapid onset and often no warning. Decisions must be made quickly and actions taken immediately. This paper provides tips for schools on: (1) Preparing for Severe Weather Emergencies; (2) Activating a Severe Weather Plan; (3) Severe Weather Plan Checklist; and (4) Periodic Drills and…

  18. REPORT ON THE EFFECT OF TEMPERATURE AND AMMONIA CONCENTRATION ON A515 CARBON STEEL IN TANK 241 AY 101 SIMULANT

    Energy Technology Data Exchange (ETDEWEB)

    DUNCAN JB; FRYE DP; WYRWAS RB

    2008-11-20

    This report documents the results from RPP-PLAN-38676, Effect of Temperature and Ammonia Concentration on A515 Carbon Steel in Tank 241-AY-101 Simulant. The purpose of this test plan was to investigate the simulant formulated for the double-shell tank (DST) 241 AY 101 (AY 101) with the addition of ammonia. The simulant was formulated from the AY-101 condensate surface layer recipe used by CC Technologies{reg_sign} in the investigation of Hanford DST chemistry, under the Expert Panel on Corrosion. AY-101 is constructed from A515 grade 60 steel. The laboratory investigation used a cylindrical corrosion coupon from this steel formulation with a surface area of 5.64 square centimeters.

  19. Effects of iron-reducing bacteria on carbon steel corrosion induced by thermophilic sulfate-reducing consortia.

    Science.gov (United States)

    Valencia-Cantero, Eduardo; Peña-Cabriales, Juan José

    2014-02-28

    Four thermophilic bacterial species, including the iron-reducing bacterium Geobacillus sp. G2 and the sulfate-reducing bacterium Desulfotomaculum sp. SRB-M, were employed to integrate a bacterial consortium. A second consortium was integrated with the same bacteria, except for Geobacillus sp. G2. Carbon steel coupons were subjected to batch cultures of both consortia. The corrosion induced by the complete consortium was 10 times higher than that induced by the second consortium, and the ferrous ion concentration was consistently higher in iron-reducing consortia. Scanning electronic microscopy analysis of the carbon steel surface showed mineral films colonized by bacteria. The complete consortium caused profuse fracturing of the mineral film, whereas the non-iron-reducing consortium did not generate fractures. These data show that the iron-reducing activity of Geobacillus sp. G2 promotes fracturing of mineral films, thereby increasing steel corrosion.

  20. Whether weather affects music

    Science.gov (United States)

    Aplin, Karen L.; Williams, Paul D.

    2012-09-01

    The creative output of composers, writers, and artists is often influenced by their surroundings. To give a literary example, it has been claimed recently that some of the characters in Oliver Twist and A Christmas Carol were based on real-life people who lived near Charles Dickens in London [Richardson, 2012]. Of course, an important part of what we see and hear is not only the people with whom we interact but also our geophysical surroundings. Of all the geophysical phenomena to influence us, the weather is arguably the most significant because we are exposed to it directly and daily. The weather was a great source of inspiration for artists Claude Monet, John Constable, and William Turner, who are known for their scientifically accurate paintings of the skies [e.g., Baker and Thornes, 2006].

  1. The Weather Man

    Institute of Scientific and Technical Information of China (English)

    蒋涵毅

    2009-01-01

    Secondly. the weather man一定会告诉我们每天的最高和最低温度(the highest and the lowest temperature)。我们用℃来表示摄氏度,有的地方则用°F,那是华氏温度。°F=9/5×℃+32

  2. Tactical Weather Expert System.

    Science.gov (United States)

    The objective of this project was to assess the feasibility of developing an expert system for tactical weather prediction. Using WILLARD, an expert ...indicate that intelligent interpretations of cloud formations can be made. These inferences can then be automatically passed to the expert system for...processing as another piece of information. It is anticipated that this technology will significantly reduce the dependence of the expert system on a

  3. Space Weather Ballooning

    Science.gov (United States)

    Phillips, Tony; Johnson, Sam; Koske-Phillips, Amelia; White, Michael; Yarborough, Amelia; Lamb, Aaron; Herbst, Anna; Molina, Ferris; Gilpin, Justin; Grah, Olivia; Perez, Ginger; Reid, Carson; Harvey, Joey; Schultz, Jamie

    2016-10-01

    We have developed a "Space Weather Buoy" for measuring upper atmospheric radiation from cosmic rays and solar storms. The Buoy, which is carried to the stratosphere by helium balloons, is relatively inexpensive and uses off-the-shelf technology accessible to small colleges and high schools. Using this device, we have measured two Forbush Decreases and a small surge in atmospheric radiation during the St. Patrick's Day geomagnetic storm of March 2015.

  4. Weathering the financial storm

    DEFF Research Database (Denmark)

    Ólafsson, Tjörvi; Pétursson, Thórarinn G.

    2011-01-01

    to explain a significant share of the cross-country variation in the depth and duration of the crisis and provide quite sharp predictions of the incidence of banking and currency crises. This suggests that country-specific initial conditions played an important role in determining the economic impact...... of the crisis and, in particular, that countries with sound fundamentals and flexible economic frameworks were better able to weather the financial storm....

  5. Areosynchronous weather imager

    Science.gov (United States)

    Puschell, Jeffery J.; Lock, Robert

    2016-09-01

    Mars is characterized by rapidly changing, poorly understood weather that is a concern for future human missions. Future Areosynchronous Mars Orbit (AMO) communication satellites offer possible platforms for Mars weather imagers similar to the geosynchronous Earth orbit (GEO) weather imagers that have been observing Earth since 1966. This paper describes an AReosynchronous Environmental Suite (ARES) that includes two imagers: one with two emissive infrared bands (10.8 μm and 12.0 μm) at 4 km resolution and the other with three VNIR bands (500 nm, 700 nm, 900 nm) at 1 km resolution. ARES stares at Mars and provides full disk coverage as fast as every 40 sec in the VNIR bands and every 2 min in the emissive bands with good sensitivity (SNR 200 in the VNIR for typical radiances and NEDT 0.2K at 180 K scene temperature in the emissive infrared). ARES size, mass, power and data rate characteristics are compatible with expectations for hosted payloads onboard future AMO communication satellites. Nevertheless, more work is needed to optimize ARES for future missions, especially in terms of trades between data rate, full disk coverage rate, sensitivity, number of spectral bands and spatial resolution and in study of approaches for maintaining accurate line of sight knowledge during data collection.

  6. Weather Monitoring Station: A Review

    Directory of Open Access Journals (Sweden)

    Mr. Dipak V. Sose

    2016-06-01

    Full Text Available Weather monitoring plays a very important role in human life hence study of weather system is necessary. Currently there are two types of the weather monitoring stations available i.e. wired and wireless. Wireless system has some advantages over the wired one hence popular now a days. The parameters are include in weather monitoring usually temperature, humidity atmospheric pressure, light intensity, rainfall etc. There are many techniques existed using different processor such as PIC, AVR, ARM etc. Analog to digital channel are used to fetch the analog output of the sensors. The wireless techniques used in the weather monitoring having GSM, FM channel, Zigbee, RF etc Protocols

  7. Can the Weather Affect My Child's Asthma?

    Science.gov (United States)

    ... Year-Old Can the Weather Affect My Child's Asthma? KidsHealth > For Parents > Can the Weather Affect My ... empeorar el asma de mi hijo? Weather and Asthma The effect of weather on asthma symptoms isn' ...

  8. Effect of Surface Treatment on the Surface Characteristics of AISI 316L Stainless Steel

    Science.gov (United States)

    Trigwell, Steve; Selvaduray, Guna

    2005-01-01

    The ability of 316L stainless steel to maintain biocompatibility, which is dependent upon the surface characteristics, is critical to its effectiveness as an implant material. The surfaces of mechanically polished (MP), electropolished (EP) and plasma treated 316L stainless steel coupons were characterized by X-ray Photoelectron Spectroscopy (XPS) and Auger Electron Spectroscopy (AES) for chemical composition, Atomic Force Microscopy for surface roughness, and contact angle measurements for critical surface tension. All surfaces had a Ni concentration that was significantly lower than the bulk concentration of -43%. The Cr content of the surface was increased significantly by electropolishing. The surface roughness was also improved significantly by electropolishing. Plasma treatment had the reverse effect - the surface Cr content was decreased. It was also found that the Cr and Fe in the surface exist in both the oxide and hydroxide states, with the ratios varying according to surface treatment.

  9. Influence of surface chemistry on the hygienic status of industrial stainless steel.

    Science.gov (United States)

    Boulange-Petermann, L; Jullien, C; Dubois, P E; Benezech, T; Faille, C

    2004-02-01

    Coupons of fourteen different stainless steels were investigated in terms of surface chemistry and ease of cleaning. Steel surfaces were exposed to Bacillus cereus spores in static saline solution for 2 h. Surfaces were rinsed and then covered with whole milk and allowed to dry. Surfaces were then cleaned in an experimental flow system that mimics an industrial application. After cleaning, remaining spores were released by sonication, spores cultured and colony forming units determined. Surfaces with higher levels of Fe in the outer surface of the passive film cleaned more easily. There was a relation between the polar component and ease of cleaning. The higher the polar component the more easily the surface cleaned. The cleaning mechanism involves dissolution of Fe enriched hydroxide films on the surface.

  10. Microstructure and Mechanical Behavior of 17-4 Precipitation Hardenable Steel Processed by Selective Laser Melting

    Science.gov (United States)

    Rafi, H. Khalid; Pal, Deepankar; Patil, Nachiket; Starr, Thomas L.; Stucker, Brent E.

    2014-12-01

    The mechanical behavior and the microstructural evolution of 17-4 precipitation hardenable (PH) stainless steel processed using selective laser melting have been studied. Test coupons were produced from 17-4 PH stainless steel powder in argon and nitrogen atmospheres. Characterization studies were carried out using mechanical testing, optical microscopy, scanning electron microscopy, and x-ray diffraction. The results show that post-process heat treatment is required to obtain typically desired tensile properties. Columnar grains of smaller diameters (<2 µm) emerged within the melt pool with a mixture of martensite and retained austenite phases. It was found that the phase content of the samples is greatly influenced by the powder chemistry, processing environment, and grain diameter.

  11. Engineering the residual stress state and microstructure of stainless steel with mechanical surface treatments

    Energy Technology Data Exchange (ETDEWEB)

    Turski, M.; Clitheroe, S.; Withers, P.J. [Manchester University, School of Materials, Manchester (United Kingdom); Evans, A.D. [Paul Scherrer Institut, Villigen-PSI (Switzerland); Rodopoulos, C. [University of Patras, Patras (Greece); Hughes, D.J. [Institut Laue Langevin, Grenoble (France)

    2010-06-15

    Four mechanical surface treatments have been considered for the application to austenitic stainless steel structures. Shot peening (SP), laser shock peening (LSP), ultrasonic impact treatment (UIT) and water jet cavitation peening (WJCP), also known as cavitation shotless peening (CSP), have been applied to 8 mm thick Type 304 austenitic stainless steel coupons. This study considers the merits of each of these mechanical surface treatments in terms of their effect on the surface roughness, microstructure, level of plastic work and through thickness residual stress distribution. Microstructural studies have revealed the formation of martensite close to the treated surface for each process. Residual stress measurements in the samples show compressive stresses to a significantly greater depth for the LSP, UIT and WJCP samples compared to the more conventional SP treated sample. (orig.)

  12. Space Weather Services of Korea

    Science.gov (United States)

    Yoon, K.; Hong, S.; Jangsuk, C.; Dong Kyu, K.; Jinyee, C.; Yeongoh, C.

    2016-12-01

    The Korean Space Weather Center (KSWC) of the National Radio Research Agency (RRA) is a government agency which is the official source of space weather information for Korean Government and the primary action agency of emergency measure to severe space weather condition. KSWC's main role is providing alerts, watches, and forecasts in order to minimize the space weather impacts on both of public and commercial sectors of satellites, aviation, communications, navigations, power grids, and etc. KSWC is also in charge of monitoring the space weather condition and conducting research and development for its main role of space weather operation in Korea. In this study, we will present KSWC's recent efforts on development of application-oriented space weather research products and services on user needs, and introduce new international collaborative projects, such as IPS-Driven Enlil model, DREAM model estimating electron in satellite orbit, global network of DSCOVR and STEREO satellites tracking, and ARMAS (Automated Radiation Measurement for Aviation Safety).

  13. Space Weather Services of Korea

    Science.gov (United States)

    Yoon, KiChang; Kim, Jae-Hun; Kim, Young Yun; Kwon, Yongki; Wi, Gwan-sik

    2016-07-01

    The Korean Space Weather Center (KSWC) of the National Radio Research Agency (RRA) is a government agency which is the official source of space weather information for Korean Government and the primary action agency of emergency measure to severe space weather condition. KSWC's main role is providing alerts, watches, and forecasts in order to minimize the space weather impacts on both of public and commercial sectors of satellites, aviation, communications, navigations, power grids, and etc. KSWC is also in charge of monitoring the space weather condition and conducting research and development for its main role of space weather operation in Korea. In this study, we will present KSWC's recent efforts on development of application-oriented space weather research products and services on user needs, and introduce new international collaborative projects, such as IPS-Driven Enlil model, DREAM model estimating electron in satellite orbit, global network of DSCOVR and STEREO satellites tracking, and ARMAS (Automated Radiation Measurement for Aviation Safety).

  14. Municipalities' Preparedness for Weather Hazards and Response to Weather Warnings

    Science.gov (United States)

    Mehiriz, Kaddour; Gosselin, Pierre

    2016-01-01

    The study of the management of weather-related disaster risks by municipalities has attracted little attention even though these organizations play a key role in protecting the population from extreme meteorological conditions. This article contributes to filling this gap with new evidence on the level and determinants of Quebec municipalities’ preparedness for weather hazards and response to related weather warnings. Using survey data from municipal emergency management coordinators and secondary data on the financial and demographic characteristics of municipalities, the study shows that most Quebec municipalities are sufficiently prepared for weather hazards and undertake measures to protect the population when informed of imminent extreme weather events. Significant differences between municipalities were noted though. Specifically, the level of preparedness was positively correlated with the municipalities’ capacity and population support for weather-related disaster management policies. In addition, the risk of weather-related disasters increases the preparedness level through its effect on population support. We also found that the response to weather warnings depended on the risk of weather-related disasters, the preparedness level and the quality of weather warnings. These results highlight areas for improvement in the context of increasing frequency and/or severity of such events with current climate change. PMID:27649547

  15. Stress and noises of steel box girders in Sutong Bridge

    Institute of Scientific and Technical Information of China (English)

    Xue Tao; Chen Zhijian; Dong Xuewu

    2008-01-01

    Sutong Bridge is a cable-stayed bridge with a main span of 1 088 m.370 high-precision stress monitoring measured data show that in the process of hoisting the steel box girders,the stress of the main girders is in the fluctuant and complex state and many meteorological factors,such as sunshine radiation,temperature and wind,have important influence on the change of stress of the steel box girders.According to the real-time weather data,the stress data after the process of wavelet denoising from representative measuring points in different weather conditions is picked to estab-lish the stress response brought by meteorological factors with Layered Separation method,thereby basically eliminating the influence of meteorological factors on the stress of main girders,so that accurate and reliable stress data can be got for steel box girders adjustment and cable-tensioned construction control.

  16. Ultrahigh carbon steels, Damascus steels, and superplasticity

    Energy Technology Data Exchange (ETDEWEB)

    Sherby, O.D. [Stanford Univ., CA (United States). Dept. of Materials Science and Engineering; Wadsworth, J. [Lawrence Livermore National Lab., CA (United States)

    1997-04-01

    The processing properties of ultrahigh carbon steels (UHCSs) have been studied at Stanford University over the past twenty years. These studies have shown that such steels (1 to 2.1% C) can be made superplastic at elevated temperature and can have remarkable mechanical properties at room temperature. It was the investigation of these UHCSs that eventually brought us to study the myths, magic, and metallurgy of ancient Damascus steels, which in fact, were also ultrahigh carbon steels. These steels were made in India as castings, known as wootz, possibly as far back as the time of Alexander the Great. The best swords are believed to have been forged in Persia from Indian wootz. This paper centers on recent work on superplastic UHCSs and on their relation to Damascus steels. 32 refs., 6 figs.

  17. Diamond-like carbon films synthesized on bearing steel surface by plasma immersion ion implantation and deposition

    Institute of Scientific and Technical Information of China (English)

    LIU Hong-xi; TANG Bao-yin; WANG Lang-ping; WANG Xiao-feng; YU Yong-hao; SUN Tao; HU Li-guo

    2004-01-01

    Diamond-like carbon (DLC) films were synthesized by plasma immersion ion implantation and deposition (PIIID) on 9Cr18 bearing steel surface. Influences of working gas pressure and pulse width of the bias voltage on properties of the thin film were investigated. The chemical compositions of the as-deposited films were characterized by Raman spectroscopy. The micro-hardness, friction and wear behavior, corrosion resistance of the samples were evaluated, respectively. Compared with uncoated substrates, micro-hardness results reveal that the maximum is increased by 88.7%. In addition, the friction coefficient decreases to about 0.1, and the corrosion resistance of treated coupons surface are improved significantly.

  18. Short-term exposure of low-alloyed steels in Qinghai Salt Lake atmosphere

    Institute of Scientific and Technical Information of China (English)

    LI QiaoXia; WANG ZhenYao; HAN Wei; YU GuoCai; HAN EnHou

    2009-01-01

    The rusts formed on carbon steel and weathering steel exposed in Oinghai Salt Lake atmosphere for 6 months were characterized by X-ray diffraction (XRD), infrared transmission spectroscopy (IRS), scanning electron microscopy (SEM), electron probe micro analyzer (EPMA) and electrochemical polarization techniques. The two kinds of steels showed the similar corrosion rate, corrosion product composition and electrochemical polarization behavior. Their rusts were mainly composed of β-FeOOH, Fe_8(O,OH)_(16)Cl_(1.3) and a little γ-FeOOH. Cl~- played an important role during the corrosion process of low-alloyed steels. The alloyed elements Cr, Ni and Cu in weathering steel were detected in the rusts; however, they showed no remarkable protective ability.

  19. The Weather in Richmond

    OpenAIRE

    Harless, William Edwin

    2014-01-01

    ABSTRACT: The Weather in Richmond is a short documentary about the Oilers, the football team at Richmond High School in downtown Richmond, California, as they struggle in 2012 with the legacy of winning no games, with the exception of a forfeit, in two years. The video documents the city of Richmond’s poverty and violence, but it also is an account of the city’s cultural diversity, of the city’s industrial history and of the hopes of some of the people who grow up there. The...

  20. Combating bad weather

    CERN Document Server

    Mukhopadhyay, Sudipta

    2015-01-01

    Every year lives and properties are lost in road accidents. About one-fourth of these accidents are due to low vision in foggy weather. At present, there is no algorithm that is specifically designed for the removal of fog from videos. Application of a single-image fog removal algorithm over each video frame is a time-consuming and costly affair. It is demonstrated that with the intelligent use of temporal redundancy, fog removal algorithms designed for a single image can be extended to the real-time video application. Results confirm that the presented framework used for the extension of the

  1. Severe Weather Forecast Decision Aid

    Science.gov (United States)

    Bauman, William H., III; Wheeler, Mark M.; Short, David A.

    2005-01-01

    This report presents a 15-year climatological study of severe weather events and related severe weather atmospheric parameters. Data sources included local forecast rules, archived sounding data, Cloud-to-Ground Lightning Surveillance System (CGLSS) data, surface and upper air maps, and two severe weather event databases covering east-central Florida. The local forecast rules were used to set threat assessment thresholds for stability parameters that were derived from the sounding data. The severe weather events databases were used to identify days with reported severe weather and the CGLSS data was used to differentiate between lightning and non-lightning days. These data sets provided the foundation for analyzing the stability parameters and synoptic patterns that were used to develop an objective tool to aid in forecasting severe weather events. The period of record for the analysis was May - September, 1989 - 2003. The results indicate that there are certain synoptic patterns more prevalent on days with severe weather and some of the stability parameters are better predictors of severe weather days based on locally tuned threat values. The results also revealed the stability parameters that did not display any skill related to severe weather days. An interactive web-based Severe Weather Decision Aid was developed to assist the duty forecaster by providing a level of objective guidance based on the analysis of the stability parameters, CGLSS data, and synoptic-scale dynamics. The tool will be tested and evaluated during the 2005 warm season.

  2. NASA Space Weather Center Services: Potential for Space Weather Research

    Science.gov (United States)

    Zheng, Yihua; Kuznetsova, Masha; Pulkkinen, Antti; Taktakishvili, A.; Mays, M. L.; Chulaki, A.; Lee, H.; Hesse, M.

    2012-01-01

    The NASA Space Weather Center's primary objective is to provide the latest space weather information and forecasting for NASA's robotic missions and its partners and to bring space weather knowledge to the public. At the same time, the tools and services it possesses can be invaluable for research purposes. Here we show how our archive and real-time modeling of space weather events can aid research in a variety of ways, with different classification criteria. We will list and discuss major CME events, major geomagnetic storms, and major SEP events that occurred during the years 2010 - 2012. Highlights of major tools/resources will be provided.

  3. Road Weather and Connected Vehicles

    Science.gov (United States)

    Pisano, P.; Boyce, B. C.

    2015-12-01

    On average, there are over 5.8 M vehicle crashes each year of which 23% are weather-related. Weather-related crashes are defined as those crashes that occur in adverse weather or on slick pavement. The vast majority of weather-related crashes happen on wet pavement (74%) and during rainfall (46%). Connected vehicle technologies hold the promise to transform road-weather management by providing improved road weather data in real time with greater temporal and geographic accuracy. This will dramatically expand the amount of data that can be used to assess, forecast, and address the impacts that weather has on roads, vehicles, and travelers. The use of vehicle-based measurements of the road and surrounding atmosphere with other, more traditional weather data sources, and create road and atmospheric hazard products for a variety of users. The broad availability of road weather data from mobile sources will vastly improve the ability to detect and forecast weather and road conditions, and will provide the capability to manage road-weather response on specific roadway links. The RWMP is currently demonstrating how weather, road conditions, and related vehicle data can be used for decision making through an innovative Integrated Mobile Observations project. FHWA is partnering with 3 DOTs (MN, MI, & NV) to pilot these applications. One is a mobile alerts application called the Motorists Advisories and Warnings (MAW) and a maintenance decision support application. These applications blend traditional weather information (e.g., radar, surface stations) with mobile vehicle data (e.g., temperature, brake status, wiper status) to determine current weather conditions. These weather conditions, and other road-travel-relevant information, are provided to users via web and phone applications. The MAW provides nowcasts and short-term forecasts out to 24 hours while the EMDSS application can provide forecasts up to 72 hours in advance. The three DOTs have placed readers and external

  4. Rough weather rescue

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-07-01

    This report, which was commissioned by the Offshore Division of the Health and Safety Executive, reviews the type of equipment and techniques used to rescue people from the water around offshore platforms in rough weather. It also examines the limitations of the equipment in extreme conditions and reports the views of the various industry sectors (as determined by a questionnaire survey). The type of incidents covered by the report include: man overboard; helicopter ditching; and evacuation from totally enclosed motor propelled survival craft (TEMPSC) and life rafts. The report considers: the approach taken by other oil-producing countries; current escape, evacuation and rescue (EER) practices for the UK Continental Shelf (UKCS); environmental limits; methods for rescue and recovery from the water and TEMPSC; launch and recovery systems; fast rescue craft (FSC) and daughter craft; emergency response and rescue vessels; helicopters; casualty personal protection equipment; claimed versus actual equipment performance; training and practice procedures; attitudes to environmental limits; lessons learnt from incidents; mechanical recovery devices; equipment design and use in rough weather; and recommendations for improvements.

  5. Weatherization Apprenticeship Program

    Energy Technology Data Exchange (ETDEWEB)

    Watson, Eric J

    2012-12-18

    Weatherization improvement services will be provided to Native people by Native people. The proposed project will recruit, train and hire two full-time weatherization technicians who will improve the energy efficiency of homes of Alaska Natives/American Indians residing in the Indian areas, within the Cook Inlet Region of Alaska. The Region includes Anchorage as well as 8 small tribal villages: The Native Villages of Eklutna, Knik, Chickaloon, Seldovia, Ninilchik, Kenaitze, Salamatof, and Tyonek. This project will be a partnership between three entities, with Cook Inlet Tribal Council (CITC) as the lead agency: CITCA's Employment and Training Services Department, Cook Inlet Housing Authority and Alaska Works Partnership. Additionally, six of the eight tribal villages within the Cook Inlet Region of Alaska have agreed to work with the project in order to improve the energy efficiency of their tribally owned buildings and homes. The remaining three villages will be invited to participate in the establishment of an intertribal consortium through this project. Tribal homes and buildings within Anchorage fall under Cook Inlet Region, Inc. (CIRI) tribal authority.

  6. Weathering of rock 'Ginger'

    Science.gov (United States)

    1997-01-01

    One of the more unusual rocks at the site is Ginger, located southeast of the lander. Parts of it have the reddest color of any material in view, whereas its rounded lobes are gray and relatively unweathered. These color differences are brought out in the inset, enhanced at the upper right. In the false color image at the lower right, the shape of the visible-wavelength spectrum (related to the abundance of weathered ferric iron minerals) is indicated by the hue of the rocks. Blue indicates relatively unweathered rocks. Typical soils and drift, which are heavily weathered, are shown in green and flesh tones. The very red color in the creases in the rock surface correspond to a crust of ferric minerals. The origin of the rock is uncertain; the ferric crust may have grown underneath the rock, or it may cement pebbles together into a conglomerate. Ginger will be a target of future super-resolution studies to better constrain its origin.Mars Pathfinder is the second in NASA's Discovery program of low-cost spacecraft with highly focused science goals. The Jet Propulsion Laboratory, Pasadena, CA, developed and manages the Mars Pathfinder mission for NASA's Office of Space Science, Washington, D.C. The Imager for Mars Pathfinder (IMP) was developed by the University of Arizona Lunar and Planetary Laboratory under contract to JPL. Peter Smith is the Principal Investigator. JPL is an operating division of the California Institute of Technology (Caltech).

  7. Reinforcing the Steel Sector

    Institute of Scientific and Technical Information of China (English)

    2009-01-01

    By pushing forward mergers between steel-makers, China gears up to consolidate the large but fragmented industryIn a government effort to consolidate the crowded steel industry and position it for fierce global competition, the state-

  8. Space Weather- Physics and Effects

    CERN Document Server

    Bothmer, Volker

    2007-01-01

    This book is a state-of-the-art review on the physics of space weather and on space weather impacts on human technology, including manned spaceflight. With contributions from a team of international experts, this comprehensive work covers all aspects of space weather physical processes, and all known aspects of space hazards from humans, both in space and on Earth. Space Weather - Physics and Effects provides the first comprehensive, scientific background of space storms caused by the sun and its impact on geospace focuses on weather issues that have become vital for the development of nationwide technological infrastructures explains magnetic storms on Earth, including the effects of EUV radiation on the atmosphere is an invaluable aid in establishing real-time weather forecasts details the threat that solar effects might have on modern telecommunication systems, including national power grid systems, aircraft and manned spaceflight.

  9. Weather Forecasting Systems and Methods

    Science.gov (United States)

    Mecikalski, John (Inventor); MacKenzie, Wayne M., Jr. (Inventor); Walker, John Robert (Inventor)

    2014-01-01

    A weather forecasting system has weather forecasting logic that receives raw image data from a satellite. The raw image data has values indicative of light and radiance data from the Earth as measured by the satellite, and the weather forecasting logic processes such data to identify cumulus clouds within the satellite images. For each identified cumulus cloud, the weather forecasting logic applies interest field tests to determine a score indicating the likelihood of the cumulus cloud forming precipitation and/or lightning in the future within a certain time period. Based on such scores, the weather forecasting logic predicts in which geographic regions the identified cumulus clouds will produce precipitation and/or lighting within during the time period. Such predictions may then be used to provide a weather map thereby providing users with a graphical illustration of the areas predicted to be affected by precipitation within the time period.

  10. Small Sensors for Space Weather

    Science.gov (United States)

    Nicholas, A. C.

    2015-12-01

    The Naval Research Laboratory is actively pursuing enhancing the nation's space weather sensing capability. One aspect of this plan is the concept of flying Space Weather sensor suites on host spacecraft as secondary payloads. The emergence and advancement of the CubeSat spacecraft architecture has produced a viable platform for scientifically and operationally relevant Space Weather sensing. This talk will provide an overview of NRL's low size weight and power sensor technologies targeting Space Weather measurements. A summary of on-orbit results of past and current missions will be presented, as well as an overview of future flights that are manifested and potential constellation missions.

  11. Bishop Paiute Weatherization Training Program

    Energy Technology Data Exchange (ETDEWEB)

    Carlos Hernandez

    2010-01-28

    The DOE Weatherization Training Grant assisted Native American trainees in developing weatherization competencies, creating employment opportunities for Bishop Paiute tribal members in a growing field. The trainees completed all the necessary training and certification requirements and delivered high-quality weatherization services on the Bishop Paiute Reservation. Six tribal members received all three certifications for weatherization; four of the trainees are currently employed. The public benefit includes (1) development of marketable skills by low-income Native individuals, (2) employment for low-income Native individuals in a growing industry, and (3) economic development opportunities that were previously not available to these individuals or the Tribe.

  12. Extracellular Electron Transfer Is a Bottleneck in the Microbiologically Influenced Corrosion of C1018 Carbon Steel by the Biofilm of Sulfate-Reducing Bacterium Desulfovibrio vulgaris.

    Directory of Open Access Journals (Sweden)

    Huabing Li

    Full Text Available Carbon steels are widely used in the oil and gas industry from downhole tubing to transport trunk lines. Microbes form biofilms, some of which cause the so-called microbiologically influenced corrosion (MIC of carbon steels. MIC by sulfate reducing bacteria (SRB is often a leading cause in MIC failures. Electrogenic SRB sessile cells harvest extracellular electrons from elemental iron oxidation for energy production in their metabolism. A previous study suggested that electron mediators riboflavin and flavin adenine dinucleotide (FAD both accelerated the MIC of 304 stainless steel by the Desulfovibrio vulgaris biofilm that is a corrosive SRB biofilm. Compared with stainless steels, carbon steels are usually far more prone to SRB attacks because SRB biofilms form much denser biofilms on carbon steel surfaces with a sessile cell density that is two orders of magnitude higher. In this work, C1018 carbon steel coupons were used in tests of MIC by D. vulgaris with and without an electron mediator. Experimental weight loss and pit depth data conclusively confirmed that both riboflavin and FAD were able to accelerate D. vulgaris attack against the carbon steel considerably. It has important implications in MIC failure analysis and MIC mitigation in the oil and gas industry.

  13. The role of goethite in the formation of the protective corrosion layer on steels

    Energy Technology Data Exchange (ETDEWEB)

    Cook, D.C. [Old Dominion University, Department of Physics (United States); Oh, S.J. [Pohang University of Science and Technology, Pohang, Department of Materials Science and Engineering (Korea, Republic of); Balasubramanian, R. [Old Dominion University, Department of Physics (United States); Yamashita, M. [Himeji Institute of Technology, Department of Mechanical Engineering (Japan)

    1999-11-15

    The corrosion products formed on carbon and weathering steels exposed in marine, industrial and rural environments in the United States for 16 years have been investigated using Moessbauer spectroscopy, Raman spectrometry and chemical analysis. Moessbauer spectroscopy was used to measure the fraction of each oxide in the corrosion coatings and micro-Raman spectrometry was used to locate and map the oxides to 2 {mu}m spatial resolution. Moessbauer spectroscopy identified the corrosion products in the weathering steels as 75% goethite, 20% lepidocrocite and 5% maghemite. Raman analysis showed that the corrosion products generally formed as alternating layers containing different oxides. For the weathering steels the protective inner-layer closest to the steel substrate consisted of nano-sized goethite ranging in size from 5-30 nm and having a mean particle size of about 12 nm. The outer-layer close to the coating surface, consisted of lepidocrocite and goethite with the former oxide being most abundant. Electron probe micro-analysis measured significant chromium in the goethite close to the steel substrate. Comparison of the goethite in the corrosion products was made with synthetic chromium substituted goethite with nearly identical microstructural characteristics being recorded. It is concluded that chromium inclusions in the goethite are important for formation of a nano-phase oxide layer which may help protect the weathering steel from further corrosion.

  14. Using Forecasting to Teach Weather Science

    Science.gov (United States)

    Tsubota, Y.; Takahashi, T.

    2009-09-01

    Weather affects our lives and hence, is a popular topic in daily conversations and in the media. Therefore, it is not only important to teach weather, but is also a good idea to use 'weather' as a topic in science teaching. Science education has two main objectives: to acquire scientific concepts and methods. Weather forecasting is an adequate theme to teach scientific methods because it is dependent on observation. However, it is not easy to forecast weather using only temporal observation. We need to know the tendency of 'weather change' via consecutive and/or continuous weather observation. Students will acquire scientific-observation skills through weather observation. Data-processing skills would be enhanced through a weather-forecasting contest. A contest should be announced within 5 days of school events, such as a school excursion and field day. Students submit their own weather forecast by gathering weather information through the internet, news paper and so on. A weather-forecasting contest compels the student to observe the weather more often. We currently have some different weather forecasts. For example, American weather-related companies such as ACCU weather and Weather Channel provide weather forecast for the many locations all over the world. Comparing these weather forecasting with actual weather, participants such as students could evaluate the differences between forecasted and actual temperatures. Participants will judge the best weather forecast based on the magnitude of the difference. Also, participants evaluate the 'hitting ratio' of each weather forecast. Students can learn elementary statistics by comparing various weather forecasts. We have developed our weather web-site that provides our own weather forecasting and observation. Students acquire science skills using our weather web-site. We will report our lessen plans and explain our weather web-site.

  15. The steel scrap age.

    Science.gov (United States)

    Pauliuk, Stefan; Milford, Rachel L; Müller, Daniel B; Allwood, Julian M

    2013-04-02

    Steel production accounts for 25% of industrial carbon emissions. Long-term forecasts of steel demand and scrap supply are needed to develop strategies for how the steel industry could respond to industrialization and urbanization in the developing world while simultaneously reducing its environmental impact, and in particular, its carbon footprint. We developed a dynamic stock model to estimate future final demand for steel and the available scrap for 10 world regions. Based on evidence from developed countries, we assumed that per capita in-use stocks will saturate eventually. We determined the response of the entire steel cycle to stock saturation, in particular the future split between primary and secondary steel production. During the 21st century, steel demand may peak in the developed world, China, the Middle East, Latin America, and India. As China completes its industrialization, global primary steel production may peak between 2020 and 2030 and decline thereafter. We developed a capacity model to show how extensive trade of finished steel could prolong the lifetime of the Chinese steelmaking assets. Secondary steel production will more than double by 2050, and it may surpass primary production between 2050 and 2060: the late 21st century can become the steel scrap age.

  16. Weather Fundamentals: Hurricanes & Tornadoes. [Videotape].

    Science.gov (United States)

    1998

    The videos in this educational series, for grades 4-7, help students understand the science behind weather phenomena through dramatic live-action footage, vivid animated graphics, detailed weather maps, and hands-on experiments. This episode (23 minutes) features information on the deadliest and most destructive storms on Earth. Through satellite…

  17. Tibetan History of Weather Monitoring

    Institute of Scientific and Technical Information of China (English)

    2004-01-01

    Modem weather monitoring began in Tibet at the end of the 19th century. In 1894, the British set up a weather monitoting station in Chunpei of Yadong,which continued to operate until August 1956. In the 1940s, the Nationalist Govemment's Ministry of Communications set up a rainfall measuring station in Qamdo, Xikang Province.

  18. Weather Modification: Finding Common Ground.

    Science.gov (United States)

    Garstang, Michael; Bruintjes, Roelof; Serafin, Robert; Orville, Harold; Boe, Bruce; Cotton, William; Warburton, Joseph

    2005-05-01

    Research and operational approaches to weather modification expressed in the National Research Council's 2003 report on “Critical Issues in Weather Modification Research” and in the Weather Modification Association's response to that report form the basis for this discussion. There is agreement that advances in the past few decades over a broad front of understanding physical processes and in technology have not been comprehensively applied to weather modification. Such advances need to be capitalized upon in the form of a concerted and sustained national effort to carry out basic and applied research in weather modification. The need for credible scientific evidence and the pressure for action should be resolved. Differences in the perception of current knowledge, the utility of numerical models, and the specific needs of research and operations in weather modification must be addressed. The increasing demand for water and the cost to society inflicted by severe weather require that the intellectual, technical, and administrative resources of the nation be combined to resolve whether and to what degree humans can influence the weather.The National Center for Atmospheric Research is sponsored by the National Science Foundation

  19. Japanese space weather research activities

    Science.gov (United States)

    Ishii, M.

    2017-01-01

    In this paper, we present existing and planned Japanese space weather research activities. The program consists of several core elements, including a space weather prediction system using numerical forecasts, a large-scale ground-based observation network, and the cooperative framework "Project for Solar-Terrestrial Environment Prediction (PSTEP)" based on a Grant-in Aid for Scientific Research on Innovative Areas.

  20. Weather to Make a Decision

    Science.gov (United States)

    Hoyle, Julie E.; Mjelde, James W.; Litzenberg, Kerry K.

    2006-01-01

    DECIDE is a teacher-friendly, integrated approach designed to stimulate learning by allowing students to make decisions about situations they face in their lives while using scientific weather principles. This learning unit integrates weather science, decision theory, mathematics, statistics, geography, and reading in a context of decision…

  1. Cool Stars and Space Weather

    CERN Document Server

    Vidotto, A A; Cameron, A C; Morin, J; Villadsen, J; Saar, S; Alvarado, J; Cohen, O; Holzwarth, V; Poppenhaeger, K; Reville, V

    2014-01-01

    Stellar flares, winds and coronal mass ejections form the space weather. They are signatures of the magnetic activity of cool stars and, since activity varies with age, mass and rotation, the space weather that extra-solar planets experience can be very different from the one encountered by the solar system planets. How do stellar activity and magnetism influence the space weather of exoplanets orbiting main-sequence stars? How do the environments surrounding exoplanets differ from those around the planets in our own solar system? How can the detailed knowledge acquired by the solar system community be applied in exoplanetary systems? How does space weather affect habitability? These were questions that were addressed in the splinter session "Cool stars and Space Weather", that took place on 9 Jun 2014, during the Cool Stars 18 meeting. In this paper, we present a summary of the contributions made to this session.

  2. Detection of Weather Radar Clutter

    DEFF Research Database (Denmark)

    Bøvith, Thomas

    2008-01-01

    Weather radars provide valuable information on precipitation in the atmosphere but due to the way radars work, not only precipitation is observed by the weather radar. Weather radar clutter, echoes from non-precipitating targets, occur frequently in the data, resulting in lowered data quality....... Especially in the application of weather radar data in quantitative precipitation estimation and forecasting a high data quality is important. Clutter detection is one of the key components in achieving this goal. This thesis presents three methods for detection of clutter. The methods use supervised...... and precipitating and non-precipitating clouds. Another method uses the difference in the motion field of clutter and precipitation measured between two radar images. Furthermore, the direction of the wind field extracted from a weather model is used. The third method uses information about the refractive index...

  3. Durability of Lacquered Aluminium Profile Considering Tropical Weather Conditions

    Directory of Open Access Journals (Sweden)

    Rigoberto Marrero Águila

    2013-11-01

    Full Text Available Searching for solutions against the degradation of materials by corrosion effect, is a common practice to use alloys such as aluminium instead of steel due to the advantages obtained. The lacquered aluminium profiles can substitute other materials like wood, in the carpentry production, becoming an economic saving. There is an increasingly use of aluminium replacing other traditional materials in the constructions in process, but its quality has been reduced in a considerable amount of installations. In this research, aluminium profiles from five different sources were submitted to a trial in natural exposition conditions at the Tropical weather condition Testing Lab, in order to evaluate their behaviour and establish, for the first time in our country, standing rules for lacquered aluminium profiles to be strictly fulfilled by manufacturers and importers. The results will allow modifying thickness standards of this type of coating, to guaranty its durability and to eliminate the failures provoked by our high severe weather conditions.

  4. Marine atmospheric corrosion of carbon steels

    Energy Technology Data Exchange (ETDEWEB)

    Morcillo, M.; Alcantara, J.; Diaz, I.; Chico, B.; Simancas, J.; Fuente, D. de la

    2015-07-01

    Basic research on marine atmospheric corrosion of carbon steels is a relatively young scientific field and there continue to be great gaps in this area of knowledge. The presence of akaganeite in the corrosion products that form on steel when it is exposed to marine atmospheres leads to a notable increase in the corrosion rate. This work addresses the following issues: (a) environmental conditions necessary for akaganeite formation; (b) characterisation of akaganeite in the corrosion products formed; (c) corrosion mechanisms of carbon steel in marine atmospheres; (d) exfoliation of rust layers formed in highly aggressive marine atmospheres; (e) long-term corrosion rate prediction; and (f) behaviour of weathering steels. Field research has been carried out at Cabo Vilano wind farm (Camarinas, Galicia) in a wide range of atmospheric salinities and laboratory work involving the use of conventional atmospheric corrosion techniques and near-surface and bulk sensitive analytical techniques: scanning electron microscopy (SEM)/energy dispersive spectrometry (EDS), X-ray diffraction (XRD), Mossbauer spectroscopy and SEM/μRaman spectroscopy. (Author)

  5. Artificial weathering of granite

    Directory of Open Access Journals (Sweden)

    Silva Hermo, B.

    2008-06-01

    Full Text Available This article summarizes a series of artificial weathering tests run on granite designed to: simulate the action of weathering agents on buildings and identify the underlying mechanisms, determine the salt resistance of different types of rock; evaluate consolidation and water-repellent treatment durability; and confirm hypotheses about the origin of salts such as gypsum that are often found in granite buildings. Salt crystallization tests were also conducted, using sodium chloride, sodium sulphate, calcium sulphate and seawater solutions. One of these tests was conducted in a chamber specifically designed to simulate salt spray weathering and another in an SO2 chamber to ascertain whether granite is subject to sulphation. The test results are analyzed and discussed, along with the shortcomings of each type of trial as a method for simulating the decay observed in monuments. The effect of factors such as wet-dry conditions, type of saline solution and the position of the planes of weakness on the type of decay is also addressed.En este trabajo se hace una síntesis de varios ensayos de alteración artificial realizados con rocas graníticas. Estos ensayos tenían distintos objetivos: reproducir las formas de alteración encontradas en los edificios para llegar a conocer los mecanismos que las generan, determinar la resistencia de las diferentes rocas a la acción de las sales, evaluar la durabilidad de tratamientos de consolidación e hidrofugación y constatar hipótesis acerca del origen de algunas sales, como el yeso, que aparecen frecuentemente en edificios graníticos. En los ensayos de cristalización de sales se utilizaron disoluciones de cloruro de sodio, sulfato de sodio, sulfato de calcio y agua de mar. Uno de estos ensayos se llevó a cabo en una cámara especialmente diseñada para reproducir la alteración por aerosol marino y otro se realizó en una cámara de SO2, con el objeto de comprobar si en rocas graníticas se puede producir

  6. Microbiologically influenced corrosion of galvanized steel by Desulfovibrio sp. and Desulfosporosinus sp. in the presence of Ag–Cu ions

    Energy Technology Data Exchange (ETDEWEB)

    Ilhan-Sungur, Esra, E-mail: esungur@istanbul.edu.tr [Istanbul University, Faculty of Science, Department of Biology, 34134 Vezneciler, Istanbul (Turkey); Unsal-Istek, Tuba [Istanbul University, Faculty of Science, Department of Biology, 34134 Vezneciler, Istanbul (Turkey); Cansever, Nurhan [Yıldız Technical University, Faculty of Chemistry-Metallurgy, Metallurgical and Materials Engineering Department, 34210 Esenler, Istanbul (Turkey)

    2015-07-15

    The effects of Ag–Cu ions on the microbiologically induced corrosion of galvanized steel in the presence of Desulfovibrio sp. and Desulfosporosinus sp. were investigated. The corrosion behavior of galvanized steel was analyzed by potentiodynamic polarization and electrochemical impedance spectroscopy. The biofilm, corrosion products and Ag–Cu ions on the surfaces were investigated by using scanning electron microscopy, energy dispersive X-ray spectrometry and elemental mapping. The biofilm layer formed by the Desulfovibrio sp. was stable covering the all surface of galvanized steel coupons, while that by Desulfosporosinus sp. was intermittent, highly porous and heterogeneous. It was found that both of the sulfate reducing bacteria species accelerated corrosion of the galvanized steel. However, it was detected that Desulfosporosinus sp. was more corrosive for galvanized steel than Desulfovibrio sp. Scanning electron microscopy images showed that Desulfovibrio sp. and Desulfosporosinus sp. in biofilm clustered into patches on the galvanized steel surface when the culture contained toxic Ag–Cu ions. The ions affected the growth of the sulfate reducing bacteria strains in different ways and hence the corrosion behaviors. It was observed that the Ag–Cu ions affected negatively growth of Desulfosporosinus sp. especially after 24 h of exposure leading to a decrease in the corrosion rate of galvanized steel. However, Desulfovibrio sp. showed more corrosive effect in the presence of the ions according to the ions-free culture. Energy dispersive X-ray spectrometry analysis showed that corrosion products on the surfaces were mainly composed of Zn, S, Na, O and P. - Highlights: • Galvanized steel was corroded by Desulfosporosinus sp. and Desulfovibrio sp. • Desulfosporosinus sp. is more corrosive than Desulfovibrio sp. • The Ag–Cu ions affected corrosion behavior of Desulfosporosinus sp. and Desulfovibrio sp. on galvanized steel.

  7. Space weathering of asteroids

    CERN Document Server

    Shestopalov, D I; Cloutis, E A

    2012-01-01

    Analysis of laboratory experiments simulating space weathering optical effects on atmosphereless planetary bodies reveals that the time needed to alter the spectrum of an ordinary chondrite meteorite to resemble the overall spectral shape and slope of an S-type asteroid is about ~ 0.1 Myr. The time required to reduce the visible albedo of samples to ~ 0.05 is ~ 1 Myr. Since both these timescales are much less than the average collisional lifetime of asteroids larger than several kilometers in size, numerous low-albedo asteroids having reddish spectra with subdued absorption bands should be observed instead of an S-type dominated population. It is not the case because asteroid surfaces cannot be considered as undisturbed, unlike laboratory samples. We have estimated the number of collisions occurring in the time of 105 yr between asteroids and projectiles of various sizes and show that impact-activated motions of regolith particles counteract the progress of optical maturation of asteroid surfaces. Continual r...

  8. Cold-Weather Sports and Your Family

    Science.gov (United States)

    ... Feeding Your 1- to 2-Year-Old Cold-Weather Sports and Your Family KidsHealth > For Parents > Cold- ... once the weather turns frosty. Beating the Cold-Weather Blahs Once a chill is in the air, ...

  9. Use of Homogeneously-Sized Carbon Steel Ball Bearings to Study Microbially-Influenced Corrosion in Oil Field Samples

    Directory of Open Access Journals (Sweden)

    Gerrit eVoordouw

    2016-03-01

    Full Text Available Microbially-influenced corrosion (MIC contributes to the general corrosion rate (CR, which is typically measured with carbon steel coupons. Here we explore the use of carbon steel ball bearings, referred to as beads (55.0 ± 0.3 mg; Ø = 0.238 cm, for determining CRs. CRs for samples from an oil field in Oceania incubated with beads were determined by the weight loss method, using acid treatment to remove corrosion products. The release of ferrous and ferric iron was also measured and CRs based on weight loss and iron determination were in good agreement. Average CRs were 0.022 mm/yr for 8 produced waters with high numbers (105/ml of acid-producing bacteria (APB, but no sulfate-reducing bacteria (SRB. Average CRs were 0.009 mm/yr for 5 central processing facility (CPF waters, which had no APB or SRB due to weekly biocide treatment and 0.036 mm/yr for 2 CPF tank bottom sludges, which had high numbers of APB (106/ml and SRB (108/ml. Hence, corrosion monitoring with carbon steel beads indicated that biocide treatment of CPF waters decreased the CR, except where biocide did not penetrate. The CR for incubations with 20 ml of a produced water decreased from 0.061 to 0.007 mm/yr when increasing the number of beads from 1 to 40. CRs determined with beads were higher than those with coupons, possibly also due to a higher weight of iron per unit volume used in incubations with coupons. Use of 1 ml syringe columns, containing carbon steel beads and injected with 10 ml/day of SRB-containing medium for 256 days gave a CR of 0.11 mm/yr under flow conditions. The standard deviation of the distribution of residual bead weights, a measure for the unevenness of the corrosion, increased with increasing CR. The most heavily corroded beads showed significant pitting. Hence the use of uniformly sized carbon steel beads offers new opportunities for screening and monitoring of corrosion including determination of the distribution of corrosion rates, which allows

  10. Space weathering on airless bodies

    Science.gov (United States)

    Pieters, Carle M.; Noble, Sarah K.

    2016-10-01

    Space weathering refers to alteration that occurs in the space environment with time. Lunar samples, and to some extent meteorites, have provided a benchmark for understanding the processes and products of space weathering. Lunar soils are derived principally from local materials but have accumulated a range of optically active opaque particles (OAOpq) that include nanophase metallic iron on/in rims formed on individual grains (imparting a red slope to visible and near-infrared reflectance) and larger iron particles (which darken across all wavelengths) such as are often found within the interior of recycled grains. Space weathering of other anhydrous silicate bodies, such as Mercury and some asteroids, produces different forms and relative abundance of OAOpq particles depending on the particular environment. If the development of OAOpq particles is minimized (such as at Vesta), contamination by exogenic material and regolith mixing become the dominant space weathering processes. Volatile-rich bodies and those composed of abundant hydrous minerals (dwarf planet Ceres, many dark asteroids, and outer solar system satellites) are affected by space weathering processes differently than the silicate bodies of the inner solar system. However, the space weathering products of these bodies are currently poorly understood and the physics and chemistry of space weathering processes in different environments are areas of active research.

  11. Cross-Beam Laser Joining of AA 6111 to Galvanized Steel in a Coach Peel Configuration

    Science.gov (United States)

    Yang, Guang; Mohammadpour, Masoud; Yazdian, Nima; Ma, Junjie; Carlson, Blair; Wang, Hui-Ping; Kovacevic, Radovan

    2017-06-01

    Cross-beam laser joining of aluminum alloy 6111 to hot-dip galvanized steel in the coach-peel configuration was investigated with the addition of AA 4047 filler wire. The filler material was not only brazed onto the galvanized steel but also partially fusion-welded with the aluminum panel. Through adjusting the laser power to 3.4 kW, a desirable wetting and spreading of filler wire on both panel surfaces could be achieved, and the thickness of intermetallic layer in the middle section of the interface between the weld bead and steel was less than 2 μm. To better understand the solid/liquid interfacial reaction at the brazing interface, two rotary Gaussian heat source models were introduced to simulate the temperature distribution in the molten pool by using the finite element method. Joint properties were examined in terms of microstructure and mechanical properties. During the tensile test, the fracture of coupons took place at the aluminum side rather than along the interface between the intermetallic layer and steel panel. No failure occurred during the three-point bending test.

  12. Chemical compatibility study of lithium titanate with Indian reduced activation ferritic martensitic steel

    Energy Technology Data Exchange (ETDEWEB)

    Sonak, Sagar, E-mail: sagarsonak@gmail.com [Fusion Reactor Materials Section, Bhabha Atomic Research Centre, Mumbai 400 085 (India); Jain, Uttam [Fusion Reactor Materials Section, Bhabha Atomic Research Centre, Mumbai 400 085 (India); Haldar, Rumu [Material Science Division, Bhabha Atomic Research Centre, Mumbai 400 085 (India); Kumar, Sanjay [Fusion Reactor Materials Section, Bhabha Atomic Research Centre, Mumbai 400 085 (India)

    2015-11-15

    Highlights: • Chemical compatibility between Li{sub 2}TiO{sub 3} and Indian RAFM steel has been studied at ITER operating temperature. • The lithium titanate chemically reacted with ferritic martensitic steel to form a brittle and non-adherent oxide layer. • The layer grew in a parabolic manner as a function of heating time. • Diffusion of oxygen (from Li{sub 2}TiO{sub 3}) appears to be controlling the oxide layer. - Abstract: Chemical compatibility between lithium titanate and Indian reduced activation ferritic-martensitic steel (In-RAFMS) was studied for the first time under ITER operating temperature. Lithium titanate required for the study was synthesized in-house. Coupons of In-RAFMS were packed inside lithium titanate powder and heated at 550 °C up to 900 h under inert argon atmosphere. The lithium titanate chemically reacted with ferritic martensitic steel to form a brittle and non-adherent oxide layer. The layer grew in a parabolic manner as a function of heating time. Microstructural and phase evolution of this oxide layer was studied using XRD, SEM and EPMA. Iron and chromium enriched zones were found within the oxide layer. Diffusion of oxygen (from Li{sub 2}TiO{sub 3}) appears to be controlling the oxide layer.

  13. Grafting of ionic liquids on stainless steel surface for antibacterial application.

    Science.gov (United States)

    Pang, Li Qing; Zhong, Li Juan; Zhou, Hui Fang; Wu, Xue E; Chen, Xiao Dong

    2015-02-01

    Stainless steel (SS) is favored for many uses due to its excellent chemical resistance, thermal stability and mechanical properties. Biofilms can be formed on stainless steel and may lead to serious hygiene problems and economic losses in many areas, e.g. food processing, public infrastructure and healthcare. For the first time, our work endeavored to make SS having antibacterial properties, ionic liquids (ILs) were grafted on SS surface via silane treatment followed by thiol-ene click reaction. The chemical structure and composition of the ILs grafted stainless-steel coupon surfaces were characterized by X-ray photoelectron spectroscopy (XPS) and attenuated total reflection-Fourier transform infrared (ATR-FTIR) spectroscopy. The antibacterial activity has been investigated, and the results showed that the ILs grafted SS surface exhibited significant antibacterial effects against Gram-negative Escherichia coli. Additionally, the results obtained here indicated that the ILs used here having bromide anion showed much better antibacterial activity against E. coli than the corresponding ILs with tetrafluoroborate and hexafluorophosphate as anions. These results obtained here can help to design novel and more efficient stainless steel having antibacterial surface.

  14. Space Weather Forecasting: An Enigma

    Science.gov (United States)

    Sojka, J. J.

    2012-12-01

    The space age began in earnest on October 4, 1957 with the launch of Sputnik 1 and was fuelled for over a decade by very strong national societal concerns. Prior to this single event the adverse effects of space weather had been registered on telegraph lines as well as interference on early WWII radar systems, while for countless eons the beauty of space weather as mid-latitude auroral displays were much appreciated. These prior space weather impacts were in themselves only a low-level science puzzle pursued by a few dedicated researchers. The technology boost and innovation that the post Sputnik era generated has almost single handedly defined our present day societal technology infrastructure. During the decade following Neil's walk on the moon on July 21, 1969 an international thrust to understand the science of space, and its weather, was in progress. However, the search for scientific understand was parsed into independent "stove pipe" categories: The ionosphere-aeronomy, the magnetosphere, the heliosphere-sun. The present day scientific infrastructure of funding agencies, learned societies, and international organizations are still hampered by these 1960's logical divisions which today are outdated in the pursuit of understanding space weather. As this era of intensive and well funded scientific research progressed so did societies innovative uses for space technologies and space "spin-offs". Well over a decade ago leaders in technology, science, and the military realized that there was indeed an adverse side to space weather that with each passing year became more severe. In 1994 several U.S. agencies established the National Space Weather Program (NSWP) to focus scientific attention on the system wide issue of the adverse effects of space weather on society and its technologies. Indeed for the past two decades a significant fraction of the scientific community has actively engaged in understanding space weather and hence crossing the "stove

  15. Extreme Weather and Natural Disasters

    CERN Document Server

    Healey, Justin

    2012-01-01

    Australia is a vast land in which weather varies significantly in different parts of the continent. Recent extreme weather events in Australia, such as the Queensland floods and Victorian bushfires, are brutal reminders of nature's devastating power. Is global warming increasing the rate of natural disasters? What part do La Niña and El Niño play in the extreme weather cycle? Cyclones, floods, severe storms, bushfires, landslides, earthquakes, tsunamis - what are the natural and man-made causes of these phenomena, how predictable are they, and how prepared are we for the impacts of natural dis

  16. STEREO Space Weather and the Space Weather Beacon

    Science.gov (United States)

    Biesecker, D. A.; Webb, D F.; SaintCyr, O. C.

    2007-01-01

    The Solar Terrestrial Relations Observatory (STEREO) is first and foremost a solar and interplanetary research mission, with one of the natural applications being in the area of space weather. The obvious potential for space weather applications is so great that NOAA has worked to incorporate the real-time data into their forecast center as much as possible. A subset of the STEREO data will be continuously downlinked in a real-time broadcast mode, called the Space Weather Beacon. Within the research community there has been considerable interest in conducting space weather related research with STEREO. Some of this research is geared towards making an immediate impact while other work is still very much in the research domain. There are many areas where STEREO might contribute and we cannot predict where all the successes will come. Here we discuss how STEREO will contribute to space weather and many of the specific research projects proposed to address STEREO space weather issues. We also discuss some specific uses of the STEREO data in the NOAA Space Environment Center.

  17. Ultrahigh Carbon Steel.

    Science.gov (United States)

    1984-10-01

    Steels have been utilized to prepare compacted powders of white cast iron (2 to 3%C) which exhibit superplastic be- havior at 650 0C and which are ductile ...strength and ductility than many of these commercially-avail- able steels. In particular, austempered fine-grained UHC steels exhibit good co7,binations of... Ductility of Rapidly Solidified White Cast Irons ", Powd. Metall., 26 (1983), pp. 155-160. (29) L. E. Eiselstein, 0. A. Ruano, J. Wadsworth, and 0. D

  18. Predictive Models for the Determination of Pitting Corrosion Versus Inhibitor Concentrations and Temperature for Radioactive Sludge in Carbon Steel Waste Tanks

    Energy Technology Data Exchange (ETDEWEB)

    Mickalonis, J.I.

    1998-10-06

    Statistical models have been developed to predict the occurrence of pitting corrosion in carbon steel waste storage tanks exposed to radioactive nuclear waste. The levels of nitrite concentrations necessary to inhibit pitting at various temperatures and nitrate concentrations were experimentally determined via electrochemical polarization and coupon immersion corrosion tests. Models for the pitting behavior were developed based on various statistical analyses of the experimental data. Feed-forward Artificial Neural Network (ANN) models, trained using the Back-Propagation of Error Algorithm, more accurately predicted conditions at which pitting occurred than the logistic regression models developed using the same data.

  19. Ultrahigh Carbon Steels

    Science.gov (United States)

    Sherby, O. D.; Oyama, T.; Kum, D. W.; Walser, B.; Wadsworth, J.

    1985-06-01

    Recent studies and results on ultrahigh carbon (UHC) steels suggest that major development efforts on these steels are timely and that programs to evaluate prototype structural components should be initiated. These recent results include: the development of economical processing techniques incorporating a divorced eutectoid transformation, the improvement of room temperature strength and ductility by heat treatment, the enhancement of superplastic properties through dilute alloying with silicon, and the attainment of exceptional notch impact strength in laminated UHC steel composites manufactured through solid state bonding. The unique mechanical properties achieved in UHC steels are due to the presence of micron-size fer-rite grains and ultrafine spheroidized carbides.

  20. KZBW Center Weather Advisory (CWA)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — The CWA is an aviation weather warning for conditions meeting or approaching national in-flight advisory (AIRMET, SIGMET or SIGMET for convection) criteria. CWAs are...

  1. Fish Springs weather CY 2011

    Data.gov (United States)

    US Fish and Wildlife Service, Department of the Interior — Weather data for calendar year 2011 at Fish Springs National Wildlife Refuge. Data is provided for each month and includes maximum temperature, minimum temperature,...

  2. Fish Springs weather CY 2010

    Data.gov (United States)

    US Fish and Wildlife Service, Department of the Interior — Weather data for calendar year 2010 at Fish Springs National Wildlife Refuge. Data is provided for each month and includes maximum temperature, minimum temperature,...

  3. The science of space weather.

    Science.gov (United States)

    Eastwood, Jonathan P

    2008-12-13

    The basic physics underpinning space weather is reviewed, beginning with a brief overview of the main causes of variability in the near-Earth space environment. Although many plasma phenomena contribute to space weather, one of the most important is magnetic reconnection, and recent cutting edge research in this field is reviewed. We then place this research in context by discussing a number of specific types of space weather in more detail. As society inexorably increases its dependence on space, the necessity of predicting and mitigating space weather will become ever more acute. This requires a deep understanding of the complexities inherent in the plasmas that fill space and has prompted the development of a new generation of scientific space missions at the international level.

  4. KZOA Center Weather Advisory (CWA)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — The CWA is an aviation weather warning for conditions meeting or approaching national in-flight advisory (AIRMET, SIGMET or SIGMET for convection) criteria. CWAs are...

  5. KZSE Center Weather Advisory (CWA)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — The CWA is an aviation weather warning for conditions meeting or approaching national in-flight advisory (AIRMET, SIGMET or SIGMET for convection) criteria. CWAs are...

  6. KZMA Center Weather Advisory (CWA)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — The CWA is an aviation weather warning for conditions meeting or approaching national in-flight advisory (AIRMET, SIGMET or SIGMET for convection) criteria. CWAs are...

  7. US Weather Bureau Storm Reports

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Weather Bureau and US Army Corps and other reports of storms from 1886-1955. Hourly precipitation from recording rain gauges captured during heavy rain, snow,...

  8. Surface Weather Observations (Pre-1893)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Monthly weather records from U.S. Army Forts stations (~1820-1871), U.S. Army Signal Service Stations (1871-1892), Smithsonian Institution voluntary observer network...

  9. KZLC Center Weather Advisory (CWA)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — The CWA is an aviation weather warning for conditions meeting or approaching national in-flight advisory (AIRMET, SIGMET or SIGMET for convection) criteria. CWAs are...

  10. Weather data communication and utilization

    Science.gov (United States)

    Mcfarland, R. H.; Nickum, J. D.; Mccall, D. L.

    1983-01-01

    The communication of weather data to aircraft is discussed. Problems encountered because of the great quantities of data available and the limited capacity to transfer this via radio link to an aircraft are discussed. Display devices are discussed.

  11. Practical Weathering for Geology Students.

    Science.gov (United States)

    Hodder, A. Peter

    1990-01-01

    The design and data management of an activity to study weathering by increasing the rate of mineral dissolution in a microwave oven is described. Data analysis in terms of parabolic and first-order kinetics is discussed. (CW)

  12. WARP Weather Information Network Server

    Data.gov (United States)

    Department of Transportation — WINS is the dissemination module of the WARP system that provides an interface to various NAS Users/systems that require weather data/products/information from WARP...

  13. Northern Hemisphere Synoptic Weather Maps

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Daily Series of Synoptic Weather Maps. Part I consists of plotted and analyzed daily maps of sea-level and 500-mb maps for 0300, 0400, 1200, 1230, 1300, and 1500...

  14. Corrosive Metabolic Activity of Desulfovibrio sp. on 316L Stainless Steel

    Science.gov (United States)

    Arkan, Simge; Ilhan-Sungur, Esra; Cansever, Nurhan

    2016-12-01

    The present study investigated the effects of chemical parameters (SO4 2-, PO4 3-, Cl-, pH) and the contents of extracellular polymeric substances (EPS) regarding the growth of Desulfovibrio sp. on the microbiologically induced corrosion of 316L stainless steel (SS). The experiments were carried out in laboratory-scaled test and control systems. 316L SS coupons were exposed to Desulfovibrio sp. culture over 720 h. The test coupons were removed at specific sampling times for enumeration of Desulfovibrio sp., determination of the corrosion rate by the weight loss measurement method and also for analysis of carbohydrate and protein in the EPS. The chemical parameters of the culture were also established. Biofilm/film formation and corrosion products on the 316L SS surfaces were investigated by scanning electron microscopy and energy-dispersive x-ray spectrometry analyses in the laboratory-scaled systems. It was found that Desulfovibrio sp. led to the corrosion of 316L SS. Both the amount of extracellular protein and chemical parameters (SO4 2- and PO4 3-) of the culture caused an increase in the corrosion of metal. There was a significantly positive relationship between the sessile and planktonic Desulfovibrio sp. counts ( p < 0.01). It was detected that the growth phases of the sessile and planktonic Desulfovibrio sp. were different from each other and the growth phases of the sessile Desulfovibrio sp. vary depending on the subspecies of Desulfovibrio sp. and the type of metal when compared with the other published studies.

  15. Microbial corrosion and cracking in steel. Fundamental studies on the electrochemical behaviour of carbon steel exposed in sulphide and sulphate-reducing environments

    Energy Technology Data Exchange (ETDEWEB)

    Rischel Hilbert, Lisbeth

    1998-08-01

    The aim of the report is to give a fundamental understanding of the response of different electrochemical techniques on carbon steel in a sulphide environment as well as in a biologically active sulphate-reducing environment (SRB). This will form the basis for further studies and for recommendations in regards to electrochemical monitoring of MIC. The work presented here and further studies are also planned to lead to a Ph.D. thesis on `MIC monitoring based on mechanisms on corrosion`. The results of laboratory experiments conducted in the period 1995 to 1997 are summarised. Conclusions will be based on results from the entire 3 year period, but only selected experimental data primarily from the latest experiments will be presented in detail here. Microbial corrosion of carbon steel under influence of sulphate-reducing bacteria (SRB) is characterised by the formation of both biofilm and corrosion products (ferrous sulphides) on the metal surface. Experiments have been conducted on carbon steel exposed in near neutral (pH 6 to 8.5) saline hydrogen sulphide environment (0 to 100 mg/l total dissolved sulphide) for a period of 14 days. Furthermore coupons have been exposed in a bioreactor for a period of up to 120 days in sulphide-producing environment controlled by biological activity of (SRB). (au)

  16. Titan: Callisto With Weather?

    Science.gov (United States)

    Moore, J. M.; Pappalardo, R. T.

    2008-12-01

    , Titan might have accreted relatively cold. Without being in a forced resonance, Titan's interior may have never undergone significant tidal heating. Analogous to Callisto's tenuous CO2 atmosphere, believed to be generated by sublimation of interior ices, interior clathrated methane within Titan may slowly diffuse outward from the cold interior, rather than the atmosphere being replenished by cryovolcanism. The hypothesis that Titan is "Callisto with weather" -- with geological processes that are principally exogenic -- can be tested through geophysical and thermal modeling, and by modeling the evolution of landscapes that are shaped by exogenic processes alone.

  17. Role of initial contamination levels, biofilm maturity and presence of salt and fat on desiccation survival of Listeria monocytogenes on stainless steel surfaces.

    Science.gov (United States)

    Hingston, Patricia A; Stea, Emma C; Knøchel, Susanne; Hansen, Truelstrup

    2013-10-01

    This study investigated the effect of initial contamination levels, biofilm maturity and presence of salt and fatty food soils on desiccation survival of Listeria monocytogenes on stainless steel (SS) coupons. L. monocytogenes cultures grown (at 15 °C for 48 h) in Tryptic Soy Broth with 1% glucose (TSB-glu) containing either 0.5 or 5% (w/v) NaCl were re-suspended in TSB-glu containing either 0.5 or 5% NaCl and used to contaminate SS coupons at levels of 3.5, 5.5, and 7.5 log CFU/cm². Desiccation (at 15 °C for 20 days, 43% RH) commenced immediately (non-biofilm) or following biofilm formation (at 15 °C for 48 h, 100% RH). To study the impact of food lipids, non-biofilm L. monocytogenes cells were suspended in TSB-glu containing either canola oil (5-10%) or lard (20-60%) and desiccated as above on SS coupons. Following desiccation for 20 days, survivors decreased by 1.4-3.7 log CFU/cm² for non-biofilm L. monocytogenes cells. The contamination level had no significant (p > 0.05) effect on survival kinetics. SEM micrographs showed mature biofilms on coupons initially contaminated with 5.5 and 7.5 log CFU/cm². Mature biofilm cells were significantly (p biofilms formed by the lowest contamination level. Besides biofilm maturity/formation, previous osmoadaptation, exposure to lard (20-60%) or salt (5%) during desiccation significantly (p biofilms and salty or fatty soils on food contact surfaces.

  18. Modern Steel Framed Schools.

    Science.gov (United States)

    American Inst. of Steel Construction, Inc., New York, NY.

    In view of the cost of structural framing for school buildings, ten steel-framed schools are examined to review the economical advantages of steel for school construction. These schools do not resemble each other in size, shape, arrangement or unit cost; some are original in concept and architecture, and others are conservative. Cost and…

  19. Efficacy of a Sonicating Swab for Removal and Capture of Listeria monocytogenes in Biofilm on Stainless Steel.

    Science.gov (United States)

    Branck, Tobyn A; Hurley, Matthew J; Prata, Gianna N; Crivello, Christina A; Marek, Patrick J

    2017-03-17

    Listeria monocytogenes is of great concern in food processing facilities because it persists in biofilms, potentiating biotransfer. Stainless steel is commonly used for food contact surfaces and transport containers. L. monocytogenes biofilm on stainless steel served as a model system for surface sampling to test the performance of a sonicating swab in comparison to a standard cotton swab. Swab performance and consistency were determined using total viable counts. Stainless steel coupons sampled with both swabs were examined with SEM to visualize biofilms and surface structures (i.e. polishing grooves and scratches). LSCM was used to image and quantitate the percent area of remaining biofilm after sampling with each swab type. The total viable count was significantly higher (P ≤ 0.05) for the sonicating swab in comparison to the standard swab within each trial. The sonicating swab was more consistent in cell recovery than standard swab having lower CVs ranging from 8.9% to 12.3% and 7.1% to 37.6% respectively. SEM imaging showed biofilm remaining in the polished grooves of the coupons sampled with the standard swab but were noticeably absent for the sonicating swab. Percent area measurement of biofilm remaining on stainless steel coupons showed significantly (P ≤ 0.05) less biofilm remained when using the sonicating swab (median 1.1%) in comparison to the standard swab (median 70.4%). The sonicating swab provided a higher recovery of cells with more consistency than the standard swab and is the first swabbing device to employ: sonication, suction, and scrubbing.IMPORTANCE Inadequate surface sampling can result in food borne illness outbreaks from biotransfer since verification of sanitization protocols relies on surface sampling and recovery of microorganisms for detection and enumeration. Swabbing is a standard method for microbiological sampling of surfaces. Although swabbing offers portability and ease of use, there are limitations, such as high user

  20. Quantitative Chemical Indices of Weathered Igneous Rocks

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    A study was conducted to compare the effectiveness of different weathering indices for characterising weathered igneous rocks of Hong Kong. Among eight chemical indices evaluated in this study, the Parker index has been found most suitable for a quantitative description of state of weathering. Based on geochemical results of 174 samples, the index decreases almost linearly with an increasing extent of weathering. The results enable a better understanding of the modification of geotechnical properties of igneous rocks associated with weathering processes.

  1. Microstructure and Texture Evolutions in AISI 1050 Steel by Flow Forming

    Energy Technology Data Exchange (ETDEWEB)

    Bedekar, Vikram [Timken Technology Center, Canton, OH; Pauskar, Praveen [Ohio State University, Columbus; Shivpuri, Rajiv [Ohio State University, Columbus; Howe, Jane Y [ORNL

    2014-01-01

    Hot rolled and annealed AISI 1050 steel cylindrical coupons were flow formed at different levels of deformation (66% and 90% wall thickness reduction). TEM studies revealed development of ultra fine (sub) grain cell structure due to severe plastic deformation. The transverse subgrain size changed from 10 m (beginning) to 300nm (66% deformation) to 40nm (90% deformation). EBSD study revealed decreased recrystallization fraction at 90% deformation compared with 66% deformation due to orientation pinning from preferred orientation along {002} planes. No evidence of dislocation pinning or cracking was observed on any samples. The aim of the present work is to study the deformation behaviour and microstructural evolution during conventional flow forming process. The study also sheds light on the strengthening behaviour and structural changes during severe straining.

  2. A study on corrosion resistant graphene films on low alloy steel

    Directory of Open Access Journals (Sweden)

    A. S. Sai Pavan

    2016-04-01

    Full Text Available Abstract Graphene nanosheets were produced after synthesizing graphene oxide via Hummer’s method and a modified Hummer’s method. The obtained graphene after reduction was dispersed in 1-propanol to get a coating solution. Mild steel coupons were coated with the graphene solution via dip coating method. Corrosion studies were carried out at different environments like water (pH 6.0, HCl (0.1 N, NaCl (3.5 wt% and NaOH (1 M. Tafel analysis showed a reduction in the corrosion rate up to 99 % after three layer deposition with the graphene developed using the modified Hummer’s method. X-ray diffraction and Raman Spectroscopy confirmed the presence of graphene.

  3. A study on corrosion resistant graphene films on low alloy steel

    Science.gov (United States)

    Sai Pavan, A. S.; Ramanan, Sutapa Roy

    2016-11-01

    Graphene nanosheets were produced after synthesizing graphene oxide via Hummer's method and a modified Hummer's method. The obtained graphene after reduction was dispersed in 1-propanol to get a coating solution. Mild steel coupons were coated with the graphene solution via dip coating method. Corrosion studies were carried out at different environments like water (pH 6.0), HCl (0.1 N), NaCl (3.5 wt%) and NaOH (1 M). Tafel analysis showed a reduction in the corrosion rate up to 99 % after three layer deposition with the graphene developed using the modified Hummer's method. X-ray diffraction and Raman Spectroscopy confirmed the presence of graphene.

  4. Coating Galvanized Steel

    Science.gov (United States)

    1989-06-01

    of special treatments other than weathering: "The "home cure" type of treatments such as washing the surface with vinegar , acetic acid, cider , copper...bonding of topcoats to smooth galvanizing have lead to such practices as washing with vinegar , washing with copper sulfate solution, or weathering before

  5. Space Weather - the Economic Case

    Science.gov (United States)

    Bisi, M. M.; Gibbs, M.

    2015-12-01

    Following on from the UK Government's placement of space weather on it's National Risk Register, in 2011, and the Royal Academy of Engineering's study into the impacts of a severe space weather event, the next piece of key evidence, to underpin future investment decisions, is understanding the socio-economic impact of space weather This poster outlines a study, funded by the UK Space Agency, which will assess the socio-economic cost of space weather, both severe events, such as 1989 & a modern day repeat of the Carrington storm and also the cost of day-to-day impacts. The study will go on to estimate the cost benefit of forecasting and also investigate options for an operational L5 spacecraft mission and knowledge exchange activities with the South African Space Agency. The findings from the initial space weather socio-economic literature review will be presented along with other findings to date and sets out the tasks for the remainder of this programme of work.

  6. Space Weather Research: Indian perspective

    Science.gov (United States)

    Bhardwaj, Anil; Pant, Tarun Kumar; Choudhary, R. K.; Nandy, Dibyendu; Manoharan, P. K.

    2016-12-01

    Space weather, just like its meteorological counterpart, is of extreme importance when it comes to its impact on terrestrial near- and far-space environments. In recent years, space weather research has acquired an important place as a thrust area of research having implications both in space science and technology. The presence of satellites and other technological systems from different nations in near-Earth space necessitates that one must have a comprehensive understanding not only of the origin and evolution of space weather processes but also of their impact on technology and terrestrial upper atmosphere. To address this aspect, nations across the globe including India have been investing in research concerning Sun, solar processes and their evolution from solar interior into the interplanetary space, and their impact on Earth's magnetosphere-ionosphere-thermosphere system. In India, over the years, a substantial amount of work has been done in each of these areas by various agencies/institutions. In fact, India has been, and continues to be, at the forefront of space research and has ambitious future programs concerning these areas encompassing space weather. This review aims at providing a glimpse of this Indian perspective on space weather research to the reader and presenting an up-to-date status of the same.

  7. Mineral phases of weathered and recent electric arc furnace dust.

    Science.gov (United States)

    Martins, Fernanda Machado; dos Reis Neto, José Manoel; da Cunha, Carlos Jorge

    2008-06-15

    A weathered and a recent sample of electric arc furnace dust (EAFD), generated in a southern Brazilian steel industry, were characterized by X-ray fluorescence spectroscopy (XFA), powder X-ray diffraction (XRD), thermogravimetric analysis (TG), scanning electron microscopy (SEM) with energy dispersive spectroscopy (EDS) probe and Fourier transform infrared spectroscopy (FTIR). A quantitative phase composition model, that accounts for the observed data and for the physico-chemical conditions of formation, was postulated for each material. One sample, in the form of a wet paste, was collected from the lowest part of a landfill and corresponds to a weathered material whereas the other sample was collected from the top portion of the landfill and corresponds to a recently produced material. The dominant cations present in both samples are iron, zinc and lead with minor amounts of manganese, calcium and silicon. The dominant mineralogical phases identified in both materials are Magnetite, Franklinite and Zincite. The recent sample has Laurionite whereas the weathered sample has Hydrocerussite and Hydrozincite.

  8. Influence of stress relief annealing on the microstructure and properties of GX12CrMoVNbN9-1(GP91 cast steel

    Directory of Open Access Journals (Sweden)

    G. Golański

    2011-04-01

    Full Text Available The paper presents an effect of stress relief annealing, applied to casts after the repair by welding, on the microstructure and mechanical properties of quenched and tempered martensitic GX12CrMoVNbN9 – 1 cast steel (called GP91. The test pieces being the subject of research were taken out from a test coupon. Heat treatment of GP91 cast steel was carried out at the parameters of temperature and time appropriate for the treatment of multi-ton steel casts, while stress relief annealing was performed at the temperatures of 730 and 750oC.After quenching and tempering GP91 cast steel was characterized by the microstructure of high-tempered martensite with numerousprecipitations of carbides of diverse size. Mechanical properties of the investigated cast steel after heat treatment fulfilled the standard requirements. Stress relief annealing contributes to the processes of recovery and recrystallization of the matrix as well as the privileged precipitation of M23C6 carbides on grain boundaries. Changes in the microstructure of the examined cast steel cause deterioration in mechanical properties – the higher the temperature of stress relief annealing, the greater the deterioration.

  9. Influence of heat treatment on microstructure and properties of GX12CrMoVNbN9-1 cast steel

    Directory of Open Access Journals (Sweden)

    G. Golański

    2010-07-01

    Full Text Available The paper presents results of research on the influence of multistage heat treatment on microstructure and properties of high-chromiummartensitic GX12CrMoVNbN9 – 1 (GP91 steel. The material under investigation were samples taken out from a test coupon. Heattreatment of GP91 cast steel was performed at the parameters of temperature and time typical of treatment for multi-ton steel casts. The research has proved that in the as-received condition (as-cast state GP91 cast steel was characterized by a coarse grain, martensitic microstructure which provided the required standard mechanical properties. The heat treatment of GP91 cast steel contributed to obtainment of a fine grain microstructure of high tempered martensite with numerous precipitations of carbides of diverse size. The GP91 cast steel structure received through heat treatment made it possible to obtain high plastic properties, particularly impact strength, maintaining strength properties on the level of the required minimum.

  10. Clean Production of Steel and Refractories in China's Steel Industry

    Institute of Scientific and Technical Information of China (English)

    SU Tiansen

    2002-01-01

    The paper describes the importance of clean production of steel and the relationships amongst sustaining development of steel industry, environment protection and the role of refractories in the clean production of steel. The main achievements and main shortcomings in the clean production of China' s steel industry have been reviewed together with the introduction of the policy supporting system and the future development of clean production in China' s steel industry.

  11. Steel: Price and Policy Issues

    Science.gov (United States)

    2006-08-31

    Inland Steel. He had also acquired a major Mexican producer, the integrated steel works on the Pacific coast at Lazaro Cardenas . But his major coup...Steel-Producing Countries Launch Talks on Banning Subsidies at OECD Meeting” (Dec. 20, 2002). 76 Nancy E. Kelly, “Steel Talks to Kick Off in Paris, Six

  12. Space Weather, Environment and Societies

    CERN Document Server

    Lilensten, Jean

    2006-01-01

    Our planet exists within a space environment affected by constantly changing solar atmosphere producing cosmic particles and electromagnetic waves. This "space weather" profoundly influences the performance of our technology because we primarily use two means for transmitting information and energy; namely, electromagnetic waves and electricity. On an everyday basis, we have developed methods to cope with the normal conditions. However, the sun remains a fiery star whose 'angry' outbursts can potentially destroy spacecrafts, kill astronauts, melt electricity transformers, stop trains, and generally wreak havoc with human activities. Space Weather is the developing field within astronomy that aims at predicting the sun’s violent activity and minimizing the impacts on our daily lives. Space Weather, Environment, and Societies explains why our technological societies are so dependent on solar activity and how the Sun disturbs the transmission of information and energy. Footnotes expand specific points and the ...

  13. Fatigue behavior in austenitic stainless steels in high-temperature water

    Science.gov (United States)

    Smith, Jean Laverty

    The fatigue life of Type 304 and Type 316NG austenitic stainless steel has been shown to be significantly lower in light water reactor environments than in air at 288°C. The focus of this study was to determine the effect of dissolved oxygen (DO) on fatigue crack initiation and early crack growth at 288°C using fully-reversed, constant strain, axial fatigue tests. The fatigue tests were chosen to evaluate fracture surface appearance, fatigue crack lengths, and fatigue crack growth rates. Additional studies were conducted to evaluate the oxide film growth kinetics of Type 304 and Type 316NG stainless steel in high-temperature water. Corrosion coupons were exposed for intervals up to 50 days to high-temperature water at 288°C with two different levels of dissolved oxygen. The coupons were evaluated for weight change, oxide film thickness, and oxide film composition. The fatigue testing and oxide evaluations conducted in this study indicate that in low-DO water, the bulk environment does not allow a passive film to form, and newly created metal surfaces do not oxidize. Fatigue cracks propagate as Mode I tensile cracks normal to the stress axis from the onset. The apparent lack of Stage I crack growth in low-DO water accounts for the significant reduction in life in this environment as compared to air. In high-DO water, the bulk environment supports the formation of a passive film and prevents the evolution of hydrogen. Crack growth initially occurs only along primary slip planes at angles 45° to the applied stress. As the crack length increases, the crack tip environment becomes increasingly independent of the bulk environment, water at the crack tip becomes unstable, and the newly created surfaces no longer re-oxidize. Subsequently, the increasing stress intensity allows slip to occur on additional planes, and the fatigue crack propagates as a Mode I tensile crack.

  14. Anoxic Corrosion of Steel and Lead in Na - Cl ± Mg-Dominated Brines in Atmospheres Containing CO2

    Science.gov (United States)

    Roselle, G. T.; Johnsen, S.; Allen, C.; Roselle, R.

    2009-12-01

    The Waste Isolation Pilot Plant (WIPP) is a deep geologic repository developed by the U.S. Department of Energy for the disposal of transuranic radioactive waste in bedded salt (Permian Salado Fm.). In order to minimize radionuclide release from the repository it is desirable to maintain these species in their least-soluble form (i.e., low oxidation states). Post-closure conditions in the WIPP will control the speciation and solubility of radionuclides in the waste. Microbially-produced CO2 from cellulosic, plastic and rubber materials in the waste may acidify any brine present and increase the actinide solubilities. Thus, the DOE emplaces MgO in the repository to buffer fCO2 and pH within ranges favoring lower actinide solubilities. Large quantities of low-C steel and Pb present in the WIPP may also consume CO2. We present initial results from a series of multiyear experiments investigating the corrosion of steel and Pb alloys under WIPP-relevant conditions. The objective is to determine the extent to which these alloys consume CO2 via the formation of carbonates or other phases, potentially supporting MgO in CO2 sequestration. In these experiments steel and Pb coupons are immersed in brines under WIPP-relevant conditions using a continuous gas flow-through system. The experimental apparatus maintains the following conditions: pO2 citrate, and oxalate); and ERDA-6 with the same organic ligands. Steel coupons removed after 6 months show formation of several phases dependent on the pCO2. SEM analysis with EDS shows the presence of a green Fe (±Mg)-chlori-hydroxide phase at pCO2 values 350 ppm. Multiple cleaning cycles were used to remove all corrosion products from the coupons, which were then weighed to determine corrosive mass loss. These data are used to calculate average corrosion rates for each experimental condition. The data show that steel corrosion rates are a strong function of pCO2 for all brine types. ERDA-6 brines appear to be more corrosive than GWB

  15. Abiotic Versus Biotic Weathering Of Olivine As Possible Biosignatures

    Science.gov (United States)

    Longazo, Teresa G.; Wentworth, Susan J.; Clemett, Simon J.; Southam, Gordon; McKay, David S.

    2001-01-01

    We are investigating the weathering of silicate minerals by both purely inorganic, and biologically mediated processes using field-emission scanning electron microscopy (FESEM) and energy dispersive x-ray spectroscopy (EDS). By resolving surface textures and chemical compositions of weathered surfaces at the sub-micron scale we hope to be able to distinguish abiotic from biotic weathering processes and so establish a new biosignature applicable to the study of astromaterials including but not limited to the Martian meteorites. Sterilized olivine grains (San Carlos, Arizona) no more than 1-2 mm in their longest dimension were optically assayed to be uniform in color and free of inclusions were selected as weathering subjects. Prior to all experiments surface morphologies and Fe/Mg ratios were determined for each grain using FE-SEM and EDS. Experiments were divided into two categories abiotic and biotic and were compared with "naturally" weathered samples. For the preliminary experiments, two trials (open and closed to the ambient laboratory environment) were performed under abiotic conditions, and three trials under biotic conditions (control, day 1 and day 2). The open system abiotic trials used sterile grains heated at 98 C and 200 C for both 24 and 48 hours in 1L double distilled de-ionized water. The closed system abiotic trials were conducted under the same conditions but in a sealed two layer steel/Teflon "bomb" apparatus. The biotic trials used sterile grains mounted in a flow-through device attached to a wellhead on the Columbia River aquifer. Several discolored, altered, grains were selected to document "natural" weathering surface textures for comparison with the experimental samples. Preliminary results indicate there are qualitative differences in weathered surface textures among all the designed experiments. The olivine grains in abiotic trials displayed etching, pitting, denticulate margins, dissolution and clay formation. The scale of the features

  16. Development of Custom 465® Corrosion-Resisting Steel for Landing Gear Applications

    Science.gov (United States)

    Daymond, Benjamin T.; Binot, Nicolas; Schmidt, Michael L.; Preston, Steve; Collins, Richard; Shepherd, Alan

    2016-04-01

    Existing high-strength low-alloy steels have been in place on landing gear for many years owing to their superior strength and cost performance. However, there have been major advances in improving the strength of high-performance corrosion-resisting steels. These materials have superior environmental robustness and remove the need for harmful protective coatings such as chromates and cadmium now on the list for removal under REACH legislation. A UK government-funded collaborative project is underway targeting a refined specification Custom 465® precipitation hardened stainless steel to replace the current material on Airbus A320 family aircraft main landing gear, a main fitting component developed by Messier-Bugatti-Dowty. This is a collaborative project between Airbus, Messier-Bugatti-Dowty, and Carpenter Technology Corporation. An extensive series of coupon tests on four production Heats of the material have been conducted, to obtain a full range of mechanical, fatigue, and corrosion properties. Custom 465® is an excellent replacement to the current material, with comparable tensile strength and fracture toughness, better ductility, and very good general corrosion and stress corrosion cracking resistance. Fatigue performance is the only significant area of deficit with respect to incumbent materials, fatigue initiation being often related to carbo-titanium-nitride particles and cleavage zones.

  17. Microstructure and Corrosion Resistance of Laser Additively Manufactured 316L Stainless Steel

    Science.gov (United States)

    Trelewicz, Jason R.; Halada, Gary P.; Donaldson, Olivia K.; Manogharan, Guha

    2016-03-01

    Additive manufacturing (AM) of metal alloys to produce complex part designs via powder bed fusion methods such as laser melting promises to be a transformative technology for advanced materials processing. However, effective implementation of AM processes requires a clear understanding of the processing-structure-properties-performance relationships in fabricated components. In this study, we report on the formation of micro and nanoscale structures in 316L stainless steel samples printed by laser AM and their implications for general corrosion resistance. A variety of techniques including x-ray diffraction, optical, scanning and transmission electron microscopy, x-ray fluorescence, and energy dispersive x-ray spectroscopy were employed to characterize the microstructure and chemistry of the laser additively manufactured 316L stainless steel, which are compared with wrought 316L coupons via electrochemical polarization. Apparent segregation of Mo has been found to contribute to a loss of passivity and an increased anodic current density. While porosity will also likely impact the environmental performance (e.g., facilitating crevice corrosion) of AM alloys, this work demonstrates the critical influence of microstructure and heterogeneous solute distributions on the corrosion resistance of laser additively manufactured 316L stainless steel.

  18. Corrosion stability of ferritic stainless steels for solid oxide electrolyser cell interconnects

    DEFF Research Database (Denmark)

    Palcut, Marián; Mikkelsen, Lars; Neufeld, Kai;

    2010-01-01

    Long-term oxidation behaviour of eight ferritic steels with 20–29 wt.% chromium (F 20 T, TUS 220 M, AL 453, Crofer 22 APU, Crofer 22 H, Sanergy HT, E-Brite and AL 29-4C) has been studied. The samples were cut into square coupons, ground and annealed for 140–1000 h at 1173 K in flowing, wet hydrogen....../EDXS. The major constituent is chromium oxide. Other oxides, such as (Mn, Cr)3O4, MnTiO3, SiO2 or Al2O3, are also present in different amounts depending on the chemical composition of the steel. The oxidation rate increases with increasing oxygen partial pressure and decreasing chromium concentration. Chromium...... diffusion coefficients in Cr2O3 and parabolic rate constants are compared. The reaction mechanism for the chromia formation is suggested. The results are discussed with respect to the applications of the steels in a working solid oxide electrolyser cell stack. Furthermore, suggestions for the development...

  19. New hypotheses for hydrogenase implication in the corrosion of mild steel

    Energy Technology Data Exchange (ETDEWEB)

    Mehanna, Maha; Basseguy, Regine; Delia, Marie-Line [Laboratoire de Genie Chimique (LGC) CNRS-INPT, 5 rue Paulin Talabot BP 1301, 31106 Toulouse (France); Girbal, Laurence; Demuez, Marie [Laboratoire d' Ingenierie des Systemes Biologiques et des Procedes (LISBP) CNRS-INSA, 135 Avenue de Rangueil, 31077 Toulouse (France); Bergel, Alain [Laboratoire de Genie Chimique (LGC) CNRS-INPT, 5 rue Paulin Talabot BP 1301, 31106 Toulouse (France)], E-mail: Alain.Bergel@ensiacet.fr

    2008-12-01

    The influence of [Fe]-hydrogenase from Clostridium acetobutylicum was studied on the anaerobic corrosion of mild steel. Two short-circuited mild steel electrodes were exposed to the same solution and hydrogenase was retained on the surface of only one electrode thanks to a dialysis membrane. The galvanic current and the electrode potential were measured as a function of time in order to monitor the difference in electrochemical behaviour induced by the presence of hydrogenase. A sharp potential decrease of around 500 mV was controlled by the deoxygenating phase. When hydrogenase was introduced after complete deoxygenation, significant heterogeneous corrosion was observed under the vivianite deposit on the electrode in contact with hydrogenase, while the other electrode only showed the vivianite deposit, which was analysed by MEB and EDX. The effect of hydrogenase was then confirmed by monitoring the free potential of single coupons exposed or not to the enzyme in a classical cell after complete deoxygenating. In both phosphate and Tris-HCl buffers, the presence of hydrogenase increased the free potential around 60 mV and induced marked general corrosion. It was concluded that [Fe]-hydrogenase acts in the absence of any final electron acceptor by catalysing direct proton reduction on the mild steel surface.

  20. Verification of Space Weather Forecasts using Terrestrial Weather Approaches

    Science.gov (United States)

    Henley, E.; Murray, S.; Pope, E.; Stephenson, D.; Sharpe, M.; Bingham, S.; Jackson, D.

    2015-12-01

    The Met Office Space Weather Operations Centre (MOSWOC) provides a range of 24/7 operational space weather forecasts, alerts, and warnings, which provide valuable information on space weather that can degrade electricity grids, radio communications, and satellite electronics. Forecasts issued include arrival times of coronal mass ejections (CMEs), and probabilistic forecasts for flares, geomagnetic storm indices, and energetic particle fluxes and fluences. These forecasts are produced twice daily using a combination of output from models such as Enlil, near-real-time observations, and forecaster experience. Verification of forecasts is crucial for users, researchers, and forecasters to understand the strengths and limitations of forecasters, and to assess forecaster added value. To this end, the Met Office (in collaboration with Exeter University) has been adapting verification techniques from terrestrial weather, and has been working closely with the International Space Environment Service (ISES) to standardise verification procedures. We will present the results of part of this work, analysing forecast and observed CME arrival times, assessing skill using 2x2 contingency tables. These MOSWOC forecasts can be objectively compared to those produced by the NASA Community Coordinated Modelling Center - a useful benchmark. This approach cannot be taken for the other forecasts, as they are probabilistic and categorical (e.g., geomagnetic storm forecasts give probabilities of exceeding levels from minor to extreme). We will present appropriate verification techniques being developed to address these forecasts, such as rank probability skill score, and comparing forecasts against climatology and persistence benchmarks. As part of this, we will outline the use of discrete time Markov chains to assess and improve the performance of our geomagnetic storm forecasts. We will also discuss work to adapt a terrestrial verification visualisation system to space weather, to help

  1. Glass Stronger than Steel

    Science.gov (United States)

    Yarris, Lynn

    2011-03-28

    A new type of damage-tolerant metallic glass, demonstrating a strength and toughness beyond that of steel or any other known material, has been developed and tested by a collaboration of researchers from Berkeley Lab and Caltech.

  2. Tomorrow's Forecast: Oceans and Weather.

    Science.gov (United States)

    Smigielski, Alan

    1995-01-01

    This issue of "Art to Zoo" focuses on weather and climate and is tied to the traveling exhibition Ocean Planet from the Smithsonian's National Museum of Natural History. The lessons encourage students to think about the profound influence the oceans have on planetary climate and life on earth. Sections of the lesson plan include: (1) "Ocean…

  3. Winter Weather Frequently Asked Questions

    Science.gov (United States)

    ... Part 3 of 3) Hot Weather Tips Heat Stress in Older Adults FAQs Extreme Heat PSAs Related Links MMWR Bibliography CDC's Program Floods Flood Readiness Personal Hygiene After a Disaster Cleanup of Flood Water After a Flood Worker Safety Educational Materials Floods ...

  4. Dynamic Weather Routes Architecture Overview

    Science.gov (United States)

    Eslami, Hassan; Eshow, Michelle

    2014-01-01

    Dynamic Weather Routes Architecture Overview, presents the high level software architecture of DWR, based on the CTAS software framework and the Direct-To automation tool. The document also covers external and internal data flows, required dataset, changes to the Direct-To software for DWR, collection of software statistics, and the code structure.

  5. Mexican Space Weather Service (SCIESMEX)

    Science.gov (United States)

    Gonzalez-Esparza, A.; De la Luz, V.; Mejia-Ambriz, J. C.; Aguilar-Rodriguez, E.; Corona-Romero, P.; Gonzalez, L. X.

    2015-12-01

    Recent modifications of the Civil Protection Law in Mexico include now specific mentions to space hazards and space weather phenomena. During the last few years, the UN has promoted international cooperation on Space Weather awareness, studies and monitoring. Internal and external conditions motivated the creation of a Space Weather Service in Mexico (SCIESMEX). The SCIESMEX (www.sciesmex.unam.mx) is operated by the Geophysics Institute at the National Autonomous University of Mexico (UNAM). The UNAM has the experience of operating several critical national services, including the National Seismological Service (SSN); besides that has a well established scientific group with expertise in space physics and solar- terrestrial phenomena. The SCIESMEX is also related with the recent creation of the Mexican Space Agency (AEM). The project combines a network of different ground instruments covering solar, interplanetary, geomagnetic, and ionospheric observations. The SCIESMEX has already in operation computing infrastructure running the web application, a virtual observatory and a high performance computing server to run numerical models. SCIESMEX participates in the International Space Environment Services (ISES) and in the Inter-progamme Coordination Team on Space Weather (ICTSW) of the Word Meteorological Organization (WMO).

  6. Life after Steel

    Science.gov (United States)

    Mangan, Katherine

    2013-01-01

    Bobby Curran grew up in a working-class neighborhood in Baltimore, finished high school, and followed his grandfather's steel-toed bootprints straight to Sparrows Point, a 3,000-acre sprawl of industry on the Chesapeake Bay. College was not part of the plan. A gritty but well-paying job at the RG Steel plant was Mr. Curran's ticket to a secure…

  7. Performance Steel Castings

    Science.gov (United States)

    2012-09-30

    alloys , foundry, muzzle brake, supply center, tooling, sources Notice Distribution Statement A Format Information Report created in Microsoft Word...Development of Sand Properties 103 Advanced Modeling Dataset.. 105 High Strength Low Alloy (HSLA) Steels 107 Steel Casting and Engineering Support...University, University of Northern Iowa, Non- Ferrous Founders’ Society, QuesTek, buyCASTINGS.com, Spokane Industries, Nova Precision Casting, Waukesha

  8. Effect of Post-weld Heat Treatment on the Mechanical Properties of Supermartensitic Stainless Steel Deposit

    Science.gov (United States)

    Zappa, Sebastián; Svoboda, Hernán; Surian, Estela

    2017-02-01

    Supermartensitic stainless steels have good weldability and adequate tensile property, toughness and corrosion resistance. They have been developed as an alternative technology, mainly for oil and gas industries. The final properties of a supermartensitic stainless steel deposit depend on its chemical composition and microstructure: martensite, tempered martensite, ferrite, retained austenite and carbides and/or nitrides. In these steels, the post-weld heat treatments (PWHTs) are usually double tempering ones, to ensure both complete tempering of martensite and high austenite content, to increase toughness and decrease hardness. The aim of this work was to study the effect of post-weld heat treatments (solution treatment with single and double tempering) on the mechanical properties of a supermartensitic stainless steel deposit. An all-weld metal test coupon was welded according to standard ANSI/AWS A5.22-95 using a GMAW supermartensitic stainless steel metal cored wire, under gas shielding. PWHTs were carried out varying the temperature of the first tempering treatment with and without a second tempering one, after solution treatment. All-weld metal chemical composition analysis, metallurgical characterization, hardness and tensile property measurements and Charpy-V tests were carried out. There are several factors which can be affected by the PWHTs, among them austenite content is a significant one. Different austenite contents (0-42%) were found. Microhardness, tensile property and toughness were affected with up to 15% of austenite content, by martensite tempering and carbide precipitation. The second tempering treatment seemed not to have had an important effect on the mechanical properties measured in this work.

  9. Evaluation of chlorine, chlorine dioxide, and a peroxyacetic acid-based sanitizer for effectiveness in killing Bacillus cereus and Bacillus thuringiensis spores in suspensions, on the surface of stainless steel, and on apples.

    Science.gov (United States)

    Kreske, Audrey C; Ryu, Jee-Hoon; Beuchat, Larry R

    2006-08-01

    Chlorine (10 to 200 microg/ml), chlorine dioxide (10 to 200 microg/ml), and a peroxyacetic acid-based sanitizer (40 and 80 microg/ ml) were evaluated for effectiveness in killing spores of Bacillus cereus and Bacillus thuringiensis in suspensions and on the surface of stainless steel and apples. Water and 5% horse serum were used as carriers for spore inoculum applied to the surface of stainless steel coupons, and 5% horse serum was used as a carrier for inoculum applied to apples. Inocula were dried on stainless steel for 5 h and on apples for 22 to 24 h before treating with sanitizers. At the concentrations of sanitizers tested, sensitivities of planktonic B. cereus and B. thuringiensis spores were similar. A portion of the spores surviving treatment with chlorine and, more markedly, chlorine dioxide had decreased tolerance to heat. Planktonic spores of both species were more sensitive to sanitizers than were spores on the surface of stainless steel or apples. At the same concentrations, chlorine was more effective than chlorine dioxide in killing spores in suspension and on stainless steel. The lethality of chlorine dioxide was markedly reduced when inoculum on stainless steel coupons was suspended in 5% horse serum as a carrier rather than water. Chlorine and chlorine dioxide at concentrations of 10 to 100 microg/ml were equally effective in killing spores on apples. Significant reductions of > or = 3.8 to 4.5 log CFU per apple were achieved by treatment with 100 microg/ml of either of the two sanitizers. The peroxyacetic acid sanitizer (40 and 80 microg/ml) was ineffective in killing Bacillus spores in the test systems investigated. Results provide information on the effectiveness of sanitizers commonly used in the food processing industry in killing Bacillus spores in suspension, on a food-contact surface, and on a ready-to-eat food.

  10. Effect of Surface Condition and Heat Treatment on Corrosion of Type 316L Stainless Steel in a Mercury Thermal Convection Loop

    Energy Technology Data Exchange (ETDEWEB)

    Pawel, S J

    2001-09-25

    Two thermal convection loops (TCLs) fabricated from 316L stainless steel and containing mercury and a variety of 316L coupons representing variable surface conditions and heat treatments have been operated continuously for 2000 h. Surface conditions included surface ground, polished, gold-coated, chemically etched, bombarded with Fe to simulate radiation damage, and oxidized. Heat treatments included solution treated, welded, and sensitized. In addition, a nitrogen doped 316L material, termed 316LN, was also examined in the solution treated condition. Duplicate TCLs were operated in this experiment--both were operated with a 305 C peak temperature, a 65 C temperature gradient, and mercury velocity of 1.2 m/min--but only one included a 36 h soak in Hg at 310 C just prior to operation to encourage wetting. Results indicate that the soak in Hg at 310 C had no lasting effect on wetting or compatibility with Hg. Further, based on examination of post-test wetting and coupon weight loss, only the gold-coated surfaces revealed significant interaction with Hg. In areas wetted significantly by Hg, the extreme surface of the stainless steel (ca 10 {micro}m) was depleted in Ni and Cr compared to the bulk composition.

  11. Effect of Surface Condition and Heat Treatment on Corrosion of Type 316L Stainless Steel in a Mercury Thermal Convection Loop

    Energy Technology Data Exchange (ETDEWEB)

    Pawel, S.J.

    2000-10-17

    Two thermal convection loops (TCLs) fabricated from 316L stainless steel and containing mercury and a variety of 316L coupons representing variable surface conditions and heat treatments have been operated continuously for 2000 h. Surface conditions included surface ground, polished, gold-coated, chemically etched, bombarded with Fe to simulate radiation damage, and oxidized. Heat treatments included solution treated, welded, and sensitized. In addition, a nitrogen doped 316L material, termed 316LN, was also examined in the solution treated condition. Duplicate TCLs were operated in this experiment--both were operated with a 305 C peak temperature, a 65 C temperature gradient, and mercury velocity of 1.2 m/min--but only one included a 36 h soak in Hg at 310 C just prior to operation to encourage wetting. Results indicate that the soak in Hg at 310 C had no lasting effect on wetting or compatibility with Hg. Further, based on examination of post-test wetting and coupon weight loss, only the gold-coated surfaces revealed significant interaction with Hg. In areas wetted significantly by Hg, the extreme surface of the stainless steel (ca 10 {micro}m) was depleted in Ni and Cr compared to the bulk composition.

  12. Weather-Corrected Performance Ratio

    Energy Technology Data Exchange (ETDEWEB)

    Dierauf, T.; Growitz, A.; Kurtz, S.; Cruz, J. L. B.; Riley, E.; Hansen, C.

    2013-04-01

    Photovoltaic (PV) system performance depends on both the quality of the system and the weather. One simple way to communicate the system performance is to use the performance ratio (PR): the ratio of the electricity generated to the electricity that would have been generated if the plant consistently converted sunlight to electricity at the level expected from the DC nameplate rating. The annual system yield for flat-plate PV systems is estimated by the product of the annual insolation in the plane of the array, the nameplate rating of the system, and the PR, which provides an attractive way to estimate expected annual system yield. Unfortunately, the PR is, again, a function of both the PV system efficiency and the weather. If the PR is measured during the winter or during the summer, substantially different values may be obtained, making this metric insufficient to use as the basis for a performance guarantee when precise confidence intervals are required. This technical report defines a way to modify the PR calculation to neutralize biases that may be introduced by variations in the weather, while still reporting a PR that reflects the annual PR at that site given the project design and the project weather file. This resulting weather-corrected PR gives more consistent results throughout the year, enabling its use as a metric for performance guarantees while still retaining the familiarity this metric brings to the industry and the value of its use in predicting actual annual system yield. A testing protocol is also presented to illustrate the use of this new metric with the intent of providing a reference starting point for contractual content.

  13. Corrosion Inhibition of Mild Steel in Seawater using Jatropha Stem

    Directory of Open Access Journals (Sweden)

    Olawale Olamide

    2016-10-01

    Full Text Available The present work investigate the inhibition of Jatropha Stem Extract (JSE in sea water using mild steel coupons of dimension 5 × 5 × 0.5 cm. The cupons were immersed in test solutions of sea water and varied concentrations of extracts of 0.1g/l to 0.9g/l was used. The functional groups of the compounds was analyzed using an FTIR. The results showed that as the concentration of the extract increases, there was a reduction in the corrosion rates. Furthermore, as the extract concentrations increased from 0.1g/l to 0.4g/l at 48hrs exposure time, the weight loss decreased by 14.3% in the medium. However, the Jatropha Stem Extract was absorbed on the substrate surface to inhibit corrosion, the morphology of phases formed from the scanning Electron Microscopy examination confirmed this trend. Hence, JSE is a good and safe inhibitor in sea water solution. The FT-IR results also indicates the presence of active corrosion inhibitor present in the Jatropha Stem.

  14. The Effect of Surface Finish on Low-Temperature Acetylene-Based Carburization of 316L Austenitic Stainless Steel

    Science.gov (United States)

    Ge, Yindong; Ernst, Frank; Kahn, Harold; Heuer, Arthur H.

    2014-12-01

    We observed a strong influence of surface finish on the efficacy of low-temperature acetylene-based carburization of AISI 316L austenitic stainless steel. Steel coupons were prepared with different surface finishes prior to carburization, from P400 SiC grit paper to 1- µm-diameter-diamond-paste. The samples with the finer surface finish developed a thicker "case" (a carbon-rich hardened surface layer) and a larger surface carbon concentration. Transmission electron microscopy revealed that the differences arose mainly from the nature of the deformation-induced disturbed layer on the steel surface. A thick (>400 nm) disturbed layer consisting of nano-crystalline grains (≈10 nm diameter) inhibits acetylene-based carburization. The experimental observations can be explained by assuming that during machining or coarse polishing, the surface oxide layer is broken up and becomes incorporated into the deformation-induced disturbed layer. The incorporated oxide-rich films retard or completely prevent the ingress of carbon into the stainless steel.

  15. 锡对低合金钢在高Cl-浓度酸性溶液中耐蚀性的影响%Effect of Tin on Corrosion Behaviour of Low Alloy Steel in Acid Solution with High Choloride Concentration

    Institute of Scientific and Technical Information of China (English)

    陈珊; 李国明; 王小燕; 陈学群

    2013-01-01

    采用动电位扫描、电化学阻抗谱(EIS)、模拟挂片试验等方法研究了锡元素对低合金钢耐蚀性的影响.结果表明,向钢中添加少量锡可以抑制钢在酸性溶液中的阳极及阴极反应,电化学阻抗谱表明添加锡后钢材的阻抗值增大,模拟实际条件的挂片试验也证实了添加锡有助于提高酸性介质中低合金钢的耐蚀性.%Some electrochemical techniques such as dynamic scanning,EIS and coupon test in simulated solution with high chloride concentration were used to investigate the effect of tin on the corrosion resistance of low alloy steel.The results show that adding a little tin in the steel can restrain the anodic and cathodic corrosion behavior of all specimens in the solution and the corrosion rate decreased with the increase of tin content.Coupon test also confirms that adding tin will enhance the corrosion resistance of the steel in acid solution with high chloride concentration.

  16. Articles comprising ferritic stainless steels

    Energy Technology Data Exchange (ETDEWEB)

    Rakowski, James M.

    2016-06-28

    An article of manufacture comprises a ferritic stainless steel that includes a near-surface region depleted of silicon relative to a remainder of the ferritic stainless steel. The article has a reduced tendency to form an electrically resistive silica layer including silicon derived from the steel when the article is subjected to high temperature oxidizing conditions. The ferritic stainless steel is selected from the group comprising AISI Type 430 stainless steel, AISI Type 439 stainless steel, AISI Type 441 stainless steel, AISI Type 444 stainless steel, and E-BRITE.RTM. alloy, also known as UNS 44627 stainless steel. In certain embodiments, the article of manufacture is a fuel cell interconnect for a solid oxide fuel cell.

  17. OpenWeather: a peer-to-peer weather data transmission protocol

    CERN Document Server

    Yanes, Adrian

    2011-01-01

    The study of the weather is performed using instruments termed weather stations. These weather stations are distributed around the world, collecting the data from the different phenomena. Several weather organizations have been deploying thousands of these instruments, creating big networks to collect weather data. These instruments are collecting the weather data and delivering it for later processing in the collections points. Nevertheless, all the methodologies used to transmit the weather data are based in protocols non adapted for this purpose. Thus, the weather stations are limited by the data formats and protocols used in them, not taking advantage of the real-time data available on them. We research the weather instruments, their technology and their network capabilities, in order to provide a solution for the mentioned problem. OpenWeather is the protocol proposed to provide a more optimum and reliable way to transmit the weather data. We evaluate the environmental factors, such as location or bandwi...

  18. Fire Danger and Fire Weather Records

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — The National Weather Service (formerly Weather Bureau) and Forest Service developed a program to track meteorological conditions conducive to forest fires, resulting...

  19. SIGWX Charts - High Level Significant Weather

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — High level significant weather (SIGWX) forecasts are provided for the en-route portion of international flights. NOAA's National Weather Service Aviation Center...

  20. Integrating Sphere-based Weathering Device

    Data.gov (United States)

    Federal Laboratory Consortium — Description:In the artificial ultraviolet (UV) weathering of materials, a need exists for weathering devices that can uniformly illuminate test specimens with a high...

  1. NOAA Weather and Climate Toolkit (WCT)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — The NOAA Weather and Climate Toolkit is an application that provides simple visualization and data export of weather and climatological data archived at NCDC. The...

  2. Newspaper Clippings and Articles (Weather-related)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Weather-related newspaper articles and photos, almost exclusively from Baltimore, MD and nearby areas. Includes storm damage, rainfall reports, and weather's affect...

  3. Rainmakers: why bad weather means good productivity.

    Science.gov (United States)

    Lee, Jooa Julia; Gino, Francesca; Staats, Bradley R

    2014-05-01

    People believe that weather conditions influence their everyday work life, but to date, little is known about how weather affects individual productivity. Contrary to conventional wisdom, we predict and find that bad weather increases individual productivity and that it does so by eliminating potential cognitive distractions resulting from good weather. When the weather is bad, individuals appear to focus more on their work than on alternate outdoor activities. We investigate the proposed relationship between worse weather and higher productivity through 4 studies: (a) field data on employees' productivity from a bank in Japan, (b) 2 studies from an online labor market in the United States, and (c) a laboratory experiment. Our findings suggest that worker productivity is higher on bad-, rather than good-, weather days and that cognitive distractions associated with good weather may explain the relationship. We discuss the theoretical and practical implications of our research.

  4. National Weather Service County Warning Area Boundaries

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains polygons corresponding to the County Warning Areas (CWAs) of each Weather Forecast Office (WFO) in the National Weather Service (NWS).

  5. National Weather Service: Watch, Warning, Advisory Display

    Science.gov (United States)

    weather.gov Site Map News Organization Search for: SPC NCEP All NOAA Search by city or zip ... Fire Wx Outlooks RSS Feeds E-Mail Alerts Weather Information Storm Reports Storm Reports Dev. NWS Hazards ...

  6. Adaptive Weather Forecasting using Local Meteorological Information

    NARCIS (Netherlands)

    Doeswijk, T.G.; Keesman, K.J.

    2005-01-01

    In general, meteorological parameters such as temperature, rain and global radiation are important for agricultural systems. Anticipating on future conditions is most often needed in these systems. Weather forecasts then become of substantial importance. As weather forecasts are subject to

  7. Weather Derivatives – Origin, Types and Application

    Directory of Open Access Journals (Sweden)

    Piotr Binkowski

    2008-03-01

    Full Text Available The number of companies that are exposed to the revenues loss risk caused by weather variability is still increasing. The businesses that are mostly exposed to weather risk are following: energy, agriculture, constructions and transport. That situation has initiated dynamic growth of weather derivatives markets as well as the awareness of the weather risk among the market participants. Presently, the weather derivatives markets evaluate rapidly in all the mature economies: USA, Asia and Europe. Constructing weather derivatives relies on qu- antifying climate factors in the form of indexes, what is quite simple task, more difficultly can be gathering precise historical data of required climate factors. Taking into consideration so far development of derivatives ñ especially the financial derivatives based on different types of indexes ñ financial market has at disposal wide range of different types of proved derivatives (futures, forward, options, swaps, which can be successfully utilised on the weather-driven markets both for hedging weather risk and speculating.

  8. World War II Weather Record Transmittances

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — World War II Weather Record Transmittances are a record of the weather and meteorological data observed during World War II and transferred to the archive. It...

  9. Internal corrosion of carbon steel piping in hot aquifers service

    Directory of Open Access Journals (Sweden)

    Simičić Miloš V.

    2011-01-01

    Full Text Available Internal corrosion of carbon steel pipelines is a major problem encountered in water service. In terms of prediction of the remaining lifetime for water pipelines based on the corrosion allowance, the three main approaches are corrosion modelling, corrosion inhibitor availability, and corrosion monitoring. In this study we used two theoretical corrosion models, CASSANDRA and NORSOK M-506 of quite different origin in order to predict uniform corrosivity of hot aquifers in eight different pipelines. Because of the varying calculation criteria for the different models, these can give very different corrosion rate predictions for the same data input. This is especially true under conditions where the formation of protective films may occur, such as at elevated temperatures. The evaluation of models was conducted by comparison using weight-loss coupons and three corrosion inhibitors were obtained from commercial suppliers. The tests were performed during the 60-day period. Even though inhibitors’ efficiencies of 98% had been achieved in laboratory testing, inhibitors’ availabilities of 85% have been used due to logistics problems and other issues. The results, given in mmpy, i.e. millimeter per year, are very consistent with NORSOK M-506 prediction. This is presumably because the model considers the effect of the formation of a passive iron carbonate film at temperatures above 80 °C and significant reduction in corrosion rate. Corrosion inhibitor A showed a better performance than inhibitors B and C in all cases but the target corrosion rates of less than 0.1 mmpy were achieved for all inhibitors. The chemical type of corrosion inhibitor A is based on quaternary amines mixed with methanol, isopropyl alcohol, xylene and ethylbenzene. Based on the obtained results the carbon steel lifetime of 30 years, provided proper inhibitors are present and 3mm corrosion allowance, can be achieved for hot aquifers service with presented water compositions.

  10. Decision Making Models Using Weather Forecast Information

    OpenAIRE

    Hiramatsu, Akio; Huynh, Van-Nam; Nakamori, Yoshiteru

    2007-01-01

    The quality of weather forecast has gradually improved, but weather information such as precipitation forecast is still uncertainty. Meteorologists have studied the use and economic value of weather information, and users have to translate weather information into their most desirable action. To maximize the economic value of users, the decision maker should select the optimum course of action for his company or project, based on an appropriate decision strategy under uncertain situations. In...

  11. Space Weather Receives First "Impact Rating"

    Science.gov (United States)

    Lanzerotti, Louis J.

    2007-08-01

    Journal Citation Reports, published by Thomson Scientific (http://scientific.thomson.com/isi/), has issued its first impact factor for Space Weather. It is 1.610. I consider this number to be very good, strongly validating the impact that Space Weather has already made in its short life within the community of space weather professionals.

  12. Space Weather Effects on Range Operations

    Science.gov (United States)

    2013-02-01

    www.windows2universe.org/space_weather/space_weather.html What are scientists talking about when they say “space weather”? How is it like weather on...particle events observed by ground level, high latitude neutron monitors and the Concorde observations are summarised in Table 1 (Refs. 12 & 13), which

  13. Reducing prediction uncertainty of weather controlled systems

    NARCIS (Netherlands)

    Doeswijk, T.G.

    2007-01-01

    In closed agricultural systems the weather acts both as a disturbance and as a resource. By using weather forecasts in control strategies the effects of disturbances can be minimized whereas the resources can be utilized. In this situation weather forecast uncertainty and model based control are cou

  14. 49 CFR 195.224 - Welding: Weather.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 3 2010-10-01 2010-10-01 false Welding: Weather. 195.224 Section 195.224 Transportation Other Regulations Relating to Transportation (Continued) PIPELINE AND HAZARDOUS MATERIALS SAFETY... PIPELINE Construction § 195.224 Welding: Weather. Welding must be protected from weather conditions...

  15. Efficient Ways to Learn Weather Radar Polarimetry

    Science.gov (United States)

    Cao, Qing; Yeary, M. B.; Zhang, Guifu

    2012-01-01

    The U.S. weather radar network is currently being upgraded with dual-polarization capability. Weather radar polarimetry is an interdisciplinary area of engineering and meteorology. This paper presents efficient ways to learn weather radar polarimetry through several basic and practical topics. These topics include: 1) hydrometeor scattering model…

  16. The Early Years: The Wonders of Weather

    Science.gov (United States)

    Ashbrook, Peggy

    2013-01-01

    This article reports on the wonders of winter weather, as it often inspires teachers' and students' interest in collecting weather data, especially if snow falls. Beginning weather data collection in preschool will introduce children to the concepts of making regular observations of natural phenomena, recording the observations (data),…

  17. Reducing prediction uncertainty of weather controlled systems

    NARCIS (Netherlands)

    Doeswijk, T.G.

    2007-01-01

    In closed agricultural systems the weather acts both as a disturbance and as a resource. By using weather forecasts in control strategies the effects of disturbances can be minimized whereas the resources can be utilized. In this situation weather forecast uncertainty and model based control are cou

  18. Efficient Ways to Learn Weather Radar Polarimetry

    Science.gov (United States)

    Cao, Qing; Yeary, M. B.; Zhang, Guifu

    2012-01-01

    The U.S. weather radar network is currently being upgraded with dual-polarization capability. Weather radar polarimetry is an interdisciplinary area of engineering and meteorology. This paper presents efficient ways to learn weather radar polarimetry through several basic and practical topics. These topics include: 1) hydrometeor scattering model…

  19. In Situ Microbial Community Succession on Mild Steel in Estuarine and Marine Environments: Exploring the Role of Iron-Oxidizing Bacteria.

    Science.gov (United States)

    McBeth, Joyce M; Emerson, David

    2016-01-01

    Microbiologically influenced corrosion (MIC) is a complex biogeochemical process involving interactions between microbes, metals, minerals, and their environment. We hypothesized that sediment-derived iron-oxidizing bacteria (FeOB) would colonize and become numerically abundant on steel surfaces incubated in coastal marine environments. To test this, steel coupons were incubated on sediments over 40 days, and samples were taken at regular intervals to examine microbial community succession. The experiments were conducted at two locations: (1) a brackish salt marsh stream and (2) a coastal marine bay. We analyzed DNA extracted from the MIC biofilms for bacterial diversity using high-throughput amplicon sequencing of the SSU rRNA gene, and two coupons from the coastal site were single cell sorted and screened for the SSU rRNA gene. We quantified communities of Zetaproteobacteria, sulfate-reducing bacteria (SRB), and total bacteria and archaea using qPCR analyses. Zetaproteobacteria and SRB were identified in the sequencing data and qPCR analyses for samples collected throughout the incubations and were also present in adjacent sediments. At the brackish site, the diversity of Zetaproteobacteria was lower on the steel compared to sediments, consistent with the expected enrichment of FeOB on steel. Their numbers increased rapidly over the first 10 days. At the marine site, Zetaproteobacteria and other known FeOB were not detected in sediments; however, the numbers of Zetaproteobacteria increased dramatically within 10 days on the steel surface, although their diversity was nearly clonal. Iron oxyhydroxide stalk biosignatures were observed on the steel and in earlier enrichment culture studies; this is evidence that the Zetaproteobacteria identified in the qPCR, pyrosequencing, and single cell data were likely FeOB. In the brackish environment, members of freshwater FeOB were also present, but were absent in the fully marine site. This work indicates there is a

  20. 基于检查片的埋地管道阴极保护检测与评估%Detection and Assessment of the Cathodic Protection for Buried Pipeline by Coupon Tests

    Institute of Scientific and Technical Information of China (English)

    伍欣; 张卓; 杨诗怡

    2016-01-01

    阴极保护作为埋地管道的主要防护措施,在管道保护方面起到重要作用。为了准确地评估管道阴极保护效果,文中介绍了管道阴极保护检查片检测技术,重点阐述了国内外发展状况以及利用检查片检测管道阴极保护效果的优势,分析了目前国外对检查片检测技术的改进方式和评价准则,对埋地管道阴极保护检查片检测评估技术提出了展望,并成功应用于某长输管道阴极保护的检测与评估。%As the main protection of buried pipelines, cathodic protection played an important role in the pipeline protec-tion. In order to accurately assess the pipeline cathodic protection, detection technology of cathodic protection by coupon was de-scribed in this article. The development status at home and abroad and the advantage of use coupon to detect the pipeline cathodic were expounded. The improvement mode and evaluation criteria of checking coupon technology, some prospects are put forwards to detection and effective evaluation technology by coupon for buried pipelines, and it is successfully applied to the detection and assessment of cathodic protection of pipeline.

  1. Simulator Of A "Weather" Cloud

    OpenAIRE

    Khramenkova, Ksenia; Hermant, Olivier; Pawlak, Renaud

    2012-01-01

    International audience; In this article a cloud simulator for the "weather" cloud is considered. The purpose of such a simulator is evaluating different cloud architectures and algorithms before implementation. The main idea is to analyze the performance beforehand, in order to avoid unsuitable algorithms being implemented in a real cloud. Two methods of request allocation policies to the nodes are considered. Their behavior in terms of interaction with nodes' cachememory is compared. Finally...

  2. Weather, Climate and Food Security

    Science.gov (United States)

    Beer, T.

    2016-12-01

    To climatologists food security is dominated by the impacts of weather and climate on food systems. But the link between the atmosphere and food security is more complex. Extreme weather events such as tropical cyclones impact directly on agriculture, but they also impact on the logistical distribution of food and can thus disrupt the food supply chain, especially in urban areas. Drought affects human life and health as well as impacting dramatically on the sustainable development of society. It represents a pending danger for vulnerable agricultural systems that depend on the rainfall, water supply and reservoirs. Developed countries are affected, but the impact is disproportionate within the developing world. Drought, especially when it results in famine, can change the life and economic development of developing nations and stifle their development for decades. A holistic approach is required to understand the phenomena, to forecast catastrophic events such as drought and famine and to predict their societal consequences. In the Food Security recommendations of the Rio+20 Forum on Science, Technology and Innovation for Sustainable Development it states that it is important "To understand fully how to measure, assess and reduce the impacts of production on the natural environment including climate change, recognizing that different measures of impact (e.g. water, land, biodiversity, carbon and other greenhouse gases, etc) may trade-off against each other..." This talk will review the historical link between weather, climate, drought and food supplies; examine the international situation; and summarise the response of the scientific community

  3. The Weather and Climate Toolkit

    Science.gov (United States)

    Ansari, S.; Del Greco, S.; Hankins, B.

    2010-12-01

    The Weather and Climate Toolkit (WCT) is free, platform independent software distributed from NOAA’s National Climatic Data Center (NCDC). The WCT allows the visualization and data export of weather and climate data, including Radar, Satellite and Model data. By leveraging the NetCDF for Java library and Common Data Model, the WCT is extremely scalable and capable of supporting many new datasets in the future. Gridded NetCDF files (regular and irregularly spaced, using Climate-Forecast (CF) conventions) are supported, along with many other formats including GRIB. The WCT provides tools for custom data overlays, Web Map Service (WMS) background maps, animations and basic filtering. The export of images and movies is provided in multiple formats. The WCT Data Export Wizard allows for data export in both vector polygon/point (Shapefile, Well-Known Text) and raster (GeoTIFF, ESRI Grid, VTK, Gridded NetCDF) formats. These data export features promote the interoperability of weather and climate information with various scientific communities and common software packages such as ArcGIS, Google Earth, MatLAB, GrADS and R. The WCT also supports an embedded, integrated Google Earth instance. The Google Earth Browser Plugin allows seamless visualization of data on a native 3-D Google Earth instance linked to the standard 2-D map. Level-II NEXRAD data for Hurricane Katrina GPCP (Global Precipitation Product), visualized in 2-D and internal Google Earth view.

  4. Positive lightning and severe weather

    Science.gov (United States)

    Price, C.; Murphy, B.

    2003-04-01

    In recent years researchers have noticed that severe weather (tornados, hail and damaging winds) are closely related to the amount of positive lightning occurring in thunderstorms. On 4 July 1999, a severe derecho (wind storm) caused extensive damage to forested regions along the United States/Canada border, west of Lake Superior. There were 665,000 acres of forest destroyed in the Boundary Waters Canoe Area Wilderness (BWCAW) in Minnesota and Quetico Provincial Park in Canada, with approximately 12.5 million trees blown down. This storm resulted in additional severe weather before and after the occurrence of the derecho, with continuous cloud-to-ground (CG) lightning occurring for more than 34 hours during its path across North America. At the time of the derecho the percentage of positive cloud-to-ground (+CG) lightning measured by the Canadian Lightning Detection Network (CLDN) was greater than 70% for more than three hours, with peak values reaching 97% positive CG lightning. Such high ratios of +CG are rare, and may be useful indicators for short-term forecasts of severe weather.

  5. Clean steels for fusion

    Energy Technology Data Exchange (ETDEWEB)

    Gelles, D.S.

    1995-03-01

    Fusion energy production has an inherent advantage over fission: a fuel supply with reduced long term radioactivity. One of the leading candidate materials for structural applications in a fusion reactor is a tungsten stabilized 9% chromium Martensitic steel. This alloy class is being considered because it offers the opportunity to maintain that advantage in the reactor structure as well as provide good high temperature strength and radiation induced swelling and embrittlement resistance. However, calculations indicate that to obtain acceptable radioactivity levels within 500 years after service, clean steel will be required because the niobium impurity levels must be kept below about 2 appm and nickel, molybdenum, nitrogen, copper, and aluminum must be intentionally restricted. International efforts are addressing the problems of clean steel production. Recently, a 5,000 kg heat was vacuum induction melted in Japan using high purity commercial raw materials giving niobium levels less than 0.7 appm. This paper reviews the need for reduced long term radioactivity, defines the advantageous properties of the tungsten stabilized Martensitic steel class, and describes the international efforts to produce acceptable clean steels.

  6. Design and Implementation of The Third Party E-Coupon System for Multi-Merchant%面向多商户的第三方电子券系统设计与实现

    Institute of Scientific and Technical Information of China (English)

    肖弘月; 吴刚

    2012-01-01

    Electronic Coupon(E-Coupon) is becoming a new technical way for business promotion. On the basis of an existing customized E-Coupon system,this paper re-organizes the original system requirements and optimizes its business process against the application background of applied in multi-merchant,meanwhile,improves the system architecture. At the same time,in order to support multi-merchant management of the new system,the analysis and design for authority management and access control based on the Role-Based Access Control model are introduced with emphasis in this paper,.%电子券正成为商家促销的一种新技术手段.在一个已有的定制化电子券系统的基础上,针对服务于多商户的应用背景,对系统的需求进行了重新梳理和流程优化,给出了改造后的系统架构.同时,还对新系统的权限管理与访问控制问题进行了重点分析和设计,引入基于角色的访问控制模型,使之能支持面向多商户的管理.

  7. Thermochemical surface engineering of steels

    DEFF Research Database (Denmark)

    Thermochemical Surface Engineering of Steels provides a comprehensive scientific overview of the principles and different techniques involved in thermochemical surface engineering, including thermodynamics, kinetics principles, process technologies and techniques for enhanced performance of steels...

  8. Continuous steel production and apparatus

    Science.gov (United States)

    Peaslee, Kent D.; Peter, Jorg J.; Robertson, David G. C.; Thomas, Brian G.; Zhang, Lifeng

    2009-11-17

    A process for continuous refining of steel via multiple distinct reaction vessels for melting, oxidation, reduction, and refining for delivery of steel continuously to, for example, a tundish of a continuous caster system, and associated apparatus.

  9. Fatigue damage of steel components

    DEFF Research Database (Denmark)

    Fæster, Søren; Zhang, Xiaodan; Huang, Xiaoxu

    2014-01-01

    Railway rails and the inner ring in roller bearings in wind turbines are both experiencing steel-to-steel contact in small areas with huge loads resulting in extremely high stresses in the base materials......Railway rails and the inner ring in roller bearings in wind turbines are both experiencing steel-to-steel contact in small areas with huge loads resulting in extremely high stresses in the base materials...

  10. Operational Space Weather Activities in the US

    Science.gov (United States)

    Berger, Thomas; Singer, Howard; Onsager, Terrance; Viereck, Rodney; Murtagh, William; Rutledge, Robert

    2016-07-01

    We review the current activities in the civil operational space weather forecasting enterprise of the United States. The NOAA/Space Weather Prediction Center is the nation's official source of space weather watches, warnings, and alerts, working with partners in the Air Force as well as international operational forecast services to provide predictions, data, and products on a large variety of space weather phenomena and impacts. In October 2015, the White House Office of Science and Technology Policy released the National Space Weather Strategy (NSWS) and associated Space Weather Action Plan (SWAP) that define how the nation will better forecast, mitigate, and respond to an extreme space weather event. The SWAP defines actions involving multiple federal agencies and mandates coordination and collaboration with academia, the private sector, and international bodies to, among other things, develop and sustain an operational space weather observing system; develop and deploy new models of space weather impacts to critical infrastructure systems; define new mechanisms for the transition of research models to operations and to ensure that the research community is supported for, and has access to, operational model upgrade paths; and to enhance fundamental understanding of space weather through support of research models and observations. The SWAP will guide significant aspects of space weather operational and research activities for the next decade, with opportunities to revisit the strategy in the coming years through the auspices of the National Science and Technology Council.

  11. Characterization of the Weatherization Assistance Program network. Weatherization Assistance Program

    Energy Technology Data Exchange (ETDEWEB)

    Mihlmester, P.E.; Koehler, W.C. Jr.; Beyer, M.A. [Aspen Systems Corp., Oak Ridge, TN (United States). Applied Management Sciences Div.; Brown, M.A. [Oak Ridge National Lab., TN (United States); Beschen, D.A. Jr. [Department of Energy, Washington, DC (United States). Office of Weatherization Assistance Programs

    1992-02-01

    The Characterization of the Weatherization Assistance Program (WAP) Network was designed to describe the national network of State and local agencies that provide WAP services to qualifying low-income households. The objective of this study was to profile the current WAP network. To achieve the objective, two national surveys were conducted: one survey collected data from 49 State WAP agencies (including the coterminous 48 States and the District of Columbia), and the second survey collected data from 920 (or 81 percent) of the local WAP agencies.

  12. A-3 steel work completed

    Science.gov (United States)

    2009-01-01

    Stennis Space Center engineers celebrated a key milestone in construction of the A-3 Test Stand on April 9 - completion of structural steel work. Workers with Lafayette (La.) Steel Erector Inc. placed the last structural steel beam atop the stand during a noon ceremony attended by more than 100 workers and guests.

  13. Joints in steel buildings

    Directory of Open Access Journals (Sweden)

    Gabriel F. Valencia Clement

    2010-04-01

    Full Text Available Masonry and steel components used in constructing buildings are in a constant state of motion. Volumetric changes are produced by temperature variation and deformation resulting from static or dynamic loading and in some materials, such as masonry, due to moisture content. This article addresses means of determining when expansion and seismic joints are required and how to proportion and design appropriate joints, specifically in steel buildings. It does not cover the study of expansion joints in concrete structures, in masonry construction or in non-structural (architectural elements.

  14. Microbial-Influenced Corrosion of Corten Steel Compared with Carbon Steel and Stainless Steel in Oily Wastewater by Pseudomonas aeruginosa

    Science.gov (United States)

    Mansouri, Hamidreza; Alavi, Seyed Abolhasan; Fotovat, Meysam

    2015-07-01

    The microbial corrosion behavior of three important steels (carbon steel, stainless steel, and Corten steel) was investigated in semi petroleum medium. This work was done in modified nutrient broth (2 g nutrient broth in 1 L oily wastewater) in the presence of Pseudomonas aeruginosa and mixed culture (as a biotic media) and an abiotic medium for 2 weeks. The behavior of corrosion was analyzed by spectrophotometric and electrochemical methods and at the end was confirmed by scanning electron microscopy. The results show that the degree of corrosion of Corten steel in mixed culture, unlike carbon steel and stainless steel, is less than P. aeruginosa inoculated medium because some bacteria affect Corten steel less than other steels. According to the experiments, carbon steel had less resistance than Corten steel and stainless steel. Furthermore, biofilm inhibits separated particles of those steels to spread to the medium; in other words, particles get trapped between biofilm and steel.

  15. Organic coatings degradation: Comparison between natural and artificial weathering

    Energy Technology Data Exchange (ETDEWEB)

    Deflorian, F. [Department of Materials Engineering and Industrial Technologies, University of Trento, Via Mesiano 77, Trento (Italy)], E-mail: defloria@ing.unitn.it; Rossi, S.; Fedel, M. [Department of Materials Engineering and Industrial Technologies, University of Trento, Via Mesiano 77, Trento (Italy)

    2008-08-15

    The protective properties of organic coated galvanised steel for outdoor applications are generally evaluated by means of accelerated laboratory tests, including electrochemical techniques. An open question is how these accelerated tests can be correlated with natural exposure in different environments. It is well known that many papers did not found any significant correlation between the natural exposure and laboratory tests. In this paper we propose a different approach. The starting point is the consideration to define the natural weathering by monitoring a few different environmental parameters affecting the organic coatings properties (energy from UV radiation, wet time, temperature, etc.), and not just considering the time of exposure. We studied two different galvanised materials: Zn and Zn-Al coatings, three different primers and one top coat. The samples were exposed for 12 months in three different natural environments: Trento (Italy), alpine region, Marseille (France) by the Mediterranean sea and Daytona (USA), a humid tropical environment. At the same time all the meteorological parameters were collected. The coatings weathering was evaluated in the laboratory after some different accelerated tests (salt spray chamber, UV exposure, cyclic test) and after natural exposure. A correlation between the 'natural stresses' and the 'artificial stresses' was investigated.

  16. Kinetics of Atmospheric Corrosion of Mild Steel in Marine and Rural Environments

    Institute of Scientific and Technical Information of China (English)

    S. Palraj; M.Selvaraj; K.Maruthan; M.Natesan

    2015-01-01

    In continuation of the extensive studies carried out to update the corrosion map of India, in this study, the degradation of mild steel by air pollutants was studied at 16 different locations from Nagore to Ammanichatram along the east coast of Tamilnadu, India over a period of two years. The weight loss study showed that the mild steel corrosion was more at Nagapattinam site, when compared to Ammanichatram and Maravakadu sites. A linear regression analysis of the experimental data was attempted to predict the mechanism of the corrosion. The composition of the corrosion products formed on the mild steel surfaces was identified by XRD technique. The corrosion rate values obtained are discussed in the light of the weathering parameters, atmospheric pollutants such as salt content & SO2 levels in the atmosphere, corrosion products formed on the mild steel surfaces.

  17. Probability for Weather and Climate

    Science.gov (United States)

    Smith, L. A.

    2013-12-01

    Over the last 60 years, the availability of large-scale electronic computers has stimulated rapid and significant advances both in meteorology and in our understanding of the Earth System as a whole. The speed of these advances was due, in large part, to the sudden ability to explore nonlinear systems of equations. The computer allows the meteorologist to carry a physical argument to its conclusion; the time scales of weather phenomena then allow the refinement of physical theory, numerical approximation or both in light of new observations. Prior to this extension, as Charney noted, the practicing meteorologist could ignore the results of theory with good conscience. Today, neither the practicing meteorologist nor the practicing climatologist can do so, but to what extent, and in what contexts, should they place the insights of theory above quantitative simulation? And in what circumstances can one confidently estimate the probability of events in the world from model-based simulations? Despite solid advances of theory and insight made possible by the computer, the fidelity of our models of climate differs in kind from the fidelity of models of weather. While all prediction is extrapolation in time, weather resembles interpolation in state space, while climate change is fundamentally an extrapolation. The trichotomy of simulation, observation and theory which has proven essential in meteorology will remain incomplete in climate science. Operationally, the roles of probability, indeed the kinds of probability one has access too, are different in operational weather forecasting and climate services. Significant barriers to forming probability forecasts (which can be used rationally as probabilities) are identified. Monte Carlo ensembles can explore sensitivity, diversity, and (sometimes) the likely impact of measurement uncertainty and structural model error. The aims of different ensemble strategies, and fundamental differences in ensemble design to support of

  18. Long-term weathering effects on the thermal performance of the Lennox/Honeywell (liquid) solar collector

    Science.gov (United States)

    1978-01-01

    The test procedures used and the results obtained during the evaluation test program of the Lennox/Honeywell double covered liquid solar collector. The tests were performed under simulated conditions, following long-term exposure to natural weathering conditions. The Lennox/Honeywell collector is a flat-plate solar collector. The absorber plate is steel with copper tubes bonded on the upper surface, and is coated with black chrome. Visual inspection of the collector indicated slight discoloration of the absorber plate. Results indicate that performance degradation had occurred. Absorptivity and/or transmissivity decreased as a result of the weathering.

  19. Evolution of Oxidative Continental Weathering

    Science.gov (United States)

    Konhauser, Kurt; Lalonde, Stefan

    2014-05-01

    The Great Oxidation Event (GOE) is currently viewed as a protracted process during which atmospheric oxygen levels increased above 10-5 times the present atmospheric level. This value is based on the loss of sulphur isotope mass independent fractionation (S-MIF) from the rock record, beginning at 2.45 Ga and disappearing by 2.32 Ga. However, a number of recent papers have pushed back the timing for oxidative continental weathering, and by extension, the onset of atmospheric oxygenation several hundreds of million years earlier despite the presence of S-MIF (e.g., Crowe et al., 2013). This apparent discrepancy can, in part, be resolved by the suggestion that recycling of older sedimentary sulphur bearing S-MIF might have led to this signal's persistence in the rock record for some time after atmospheric oxygenation (Reinhard et al., 2013). Here we suggest another possibility, that the earliest oxidative weathering reactions occurred in environments at profound redox disequilibrium with the atmosphere, such as biological soil crusts, riverbed and estuarine sediments, and lacustrine microbial mats. We calculate that the rate of O2 production via oxygenic photosynthesis in these terrestrial microbial ecosystems provides largely sufficient oxidizing potential to mobilise sulphate and a number of redox-sensitive trace metals from land to the oceans while the atmosphere itself remained anoxic with its attendant S-MIF signature. These findings reconcile geochemical signatures in the rock record for the earliest oxidative continental weathering with the history of atmospheric sulphur chemistry, and demonstrate the plausible antiquity of a terrestrial biosphere populated by cyanobacteria. Crowe, S.A., Dossing, L.N., Beukes, N.J., Bau, M., Kruger, S.J., Frei, R. & Canfield, D.E. Atmospheric oxygenation three billion years ago. Nature 501, 535-539 (2013). Reinhard, C.T., Planavsky, N.J. & Lyons, T.W. Long-term sedimentary recycling of rare sulphur isotope anomalies. Nature 497

  20. Insurance adaptation to extreme weather

    Energy Technology Data Exchange (ETDEWEB)

    Wakeford, C. [Institute for Catastrophic Loss Reduction, Toronto, ON (Canada)

    2005-07-01

    This paper examined the role of climate change as a catalyst for specific changes in insurance practices. The presentation addressed how insurance companies are adapting behaviours in response to increasing climate variability and growth in severe weather damage. It discussed ancient examples of insurance as well as more modern insurance practices. Statistics on the number of disasters, global natural disaster economic and insured losses and infrastructure spending are presented. Internal adaptation such as prospective underwriting and incentives and external adaptation such as working with governments and organizations and individuals were also discussed. It was concluded that directions for the future include continued research, heightened awareness and more resilient communities. 3 tabs.

  1. Precipitates in electrical steels

    Energy Technology Data Exchange (ETDEWEB)

    Jenkins, Keith [Development and Market Research, Cogent Power Limited, Corporation Road, Newport, South Wales NP19 OXT (United Kingdom)], E-mail: keith.jenkins@cogent-power.com; Lindenmo, Magnus [Development and Market Research, Cogent Power Limited, Corporation Road, Newport, South Wales NP19 OXT (United Kingdom)

    2008-10-15

    Precipitates heavily influence the magnetic properties of electrical steels, either as a key controlled requirement as part of the manufacturing process or as an unwanted harmful residual in the final product. In this current work copper-manganese sulphides precipitates are the primary inhibitor species in the conventional grain-oriented (CGO) steels examined and grain boundary pinning is effective at a mean precipitate size of 30-70 nm. The growth of CuMnS has been studied and the results show that a precipitate size above {approx}100 nm allows the onset of secondary recrystallisation in the heating conditions applied. The effect of precipitates on the magnetic properties of both grain-oriented and non-oriented steels in their final product form is then examined. Examples of grain-oriented material still containing large numbers of precipitates clearly show the detrimental effects with increases in total power loss of 40% or more. Loss deterioration by about 20% is also seen in samples of high silicon non-oriented material in which titanium carbo-nitride precipitates have been observed. In this case the precipitates are believed to have formed during cooling after final annealing. Finally a grain-oriented steel with a large number of very small precipitates, which do not seem to have any harmful effect on the magnetic properties, is demonstrated.

  2. Japan steel mill perspective

    Energy Technology Data Exchange (ETDEWEB)

    Murase, K. [Kobe Steel Ltd., Tokyo (Japan)

    2004-07-01

    The international and Japan's steel industry, the coking coal market, and Japan's expectations from Canada's coal industry are discussed. Japan's steel mills are operating at full capacity. Crude steel production for the first half of 2004 was 55.8 million tons. The steel mills are profitable, but costs are high, and there are difficulties with procuring raw materials. Japan is trying to enhance the quality of coke, in order to achieve higher productivity in the production of pig iron. Economic growth is rising disproportionately in the BRICs (Brazil, Russia, India, and China), with a large increase in coking coal demand from China. On the supply side, there are several projects underway in Australia and Canada to increase production. These include new developments by Elk Valley Coal Corporation, Grande Cache Coal, Western Canadian Coal, and Northern Energy and Mining in Canada. The Elga Mine in the far eastern part of Russia is under development. But the market is expected to remain tight for some time. Japan envisions Canadian coal producers will provide a stable coal supply, expansion of production and infrastructure capabilities, and stabilization of price. 16 slides/overheads are included.

  3. COUPON BETTING: THE FOOTBALL FUNGUS

    National Research Council Canada - National Science Library

    RUSSELL, CHARLES E. B

    1913-01-01

    OF our great purely national games cricket and football are universally and rightly regarded as the most popular, but there can be little doubt that great as is the popularity of cricket, the interest...

  4. Weathering of ordinary chondrites from Oman: Correlation of weathering parameters with 14C terrestrial ages and a refined weathering scale

    Science.gov (United States)

    Zurfluh, Florian J.; Hofmann, Beda A.; Gnos, Edwin; Eggenberger, Urs; Jull, A. J. Timothy

    2016-09-01

    We have investigated 128 14C-dated ordinary chondrites from Oman for macroscopically visible weathering parameters, for thin section-based weathering degrees, and for chemical weathering parameters as analyzed with handheld X-ray fluorescence. These 128 14C-dated meteorites show an abundance maximum of terrestrial age at 19.9 ka, with a mean of 21.0 ka and a pronounced lack of samples between 0 and 10 ka. The weathering degree is evaluated in thin section using a refined weathering scale based on the current W0 to W6 classification of Wlotzka (1993), with five newly included intermediate steps resulting in a total of nine (formerly six) steps. We find significant correlations between terrestrial ages and several macroscopic weathering parameters. The correlation of various chemical parameters including Sr and Ba with terrestrial age is not very pronounced. The microscopic weathering degree of metal and sulfides with newly added intermediate steps shows the best correlation with 14C terrestrial ages, demonstrating the significance of the newly defined weathering steps. We demonstrate that the observed 14C terrestrial age distribution can be modeled from the abundance of meteorites with different weathering degrees, allowing the evaluation of an age-frequency distribution for the whole meteorite population.

  5. Finite element analysis of fibre augmented steel technology pipe (FAST-PIPEtm)

    Energy Technology Data Exchange (ETDEWEB)

    Chen, Qishi; Yoosef-Ghodsi, Nader [C-FER Technologies, Edmonton, Alberta, (Canada); Salama, Mamdouh [ConocoPhillips Company, Houston, Texas, (United States)

    2010-07-01

    FAST-PipeTM is fabricated from a steel liner hoop-wound with non-impregnated fibreglass strands. The design of this new technology requires developing analytical methods. This paper reported how the finite element program ABAQUS has been used to develop shell models capable of simulating the burst and bending behaviour of FAST-PIPETM. Experimental measurements were performed on 48 and 12 inch pipes to calibrate and to validate the finite element analysis models. The material properties were obtained using coupon tests, and the elastic modulus of the fibre wrap using burst tests. The results showed that the failure of both the burst and bend models was defined as the point where the wrap hoop strain reached a failure strain of about 2%. It is found that the analytical model was accurate based on the burst test results. Also, the moment capacity is not affected by the wrap elasticity modulus value and the type of yield criteria used for the steel liner.

  6. Microbial consortium influence upon steel corrosion rate, using polarisation resistance and electrochemical noise techniques

    Energy Technology Data Exchange (ETDEWEB)

    Hernandez Gayosso, M.J.; Zavala Olivares, G.; Ruiz Ordaz, N.; Juarez Ramirez, C.; Garcia Esquivel, R.; Padilla Viveros, A

    2004-10-01

    The microbiologically influenced corrosion (MIC) is a process, which affects the oil industry, particularly the hydrocarbons extraction, transport and storage. MIC evaluation has been normally based upon microbiological tests, and just a few references mention alternating methods, such as the electrochemical techniques, which can be used as criteria for their evaluation. In this work, two different electrochemical laboratory techniques, polarisation resistance and electrochemical noise were used, in order to determine the corrosion behaviour of a microbial consortium, obtained from a gas transporting pipeline, located in the southeast of Mexico. The bacteria population growth was found to be different for sessile and plancktonic microorganisms. Moreover, long incubation times were required to reach the maximum concentration of sessile bacteria. The electrochemical techniques used in this study exhibited a similar tendency on the corrosion rate behaviour with time, and values above 0.3 mm year{sup -1} were observed at the end of the experiments. The experiments were complemented with surface analysis. Scanning electron microscope observation of APIXL52 steel coupons, exposed to the consortium action, revealed bacteria presence, as well as a damaged steel surface. A type of localized corrosion was observed on the metal surface, and it was associated to the bacteria effect.

  7. Inhibition of Staphylococcus aureus by antimicrobial biofilms formed by competitive exclusion microorganisms on stainless steel.

    Science.gov (United States)

    Son, Hyeri; Park, Sunhyung; Beuchat, Larry R; Kim, Hoikyung; Ryu, Jee-Hoon

    2016-12-05

    The goal of this study was to develop a desiccation resistant antimicrobial surface using biofilm of competitive exclusion (CE) microorganism inhibitory to Staphylococcus aureus. We isolated 161 microorganisms from soils, foods, and food-contact surfaces that are inhibitory to S. aureus. Among them, three CE microorganisms (Streptomyces spororaveus strain Gaeunsan-18, Bacillus safensis strain Chamnamu-sup 5-25, and Pseudomonas azotoformans strain Lettuce-9) exhibiting strong antibacterial activity and high growth rates were selected for evaluation. These isolates formed biofilms within 24h on stainless steel coupons (SSCs) immersed in Bennet's broth and tryptic soy broth at 25°C. Cells in these biofilms showed significantly (P≤0.05) enhanced resistance to a desiccation (43% relative humidity [RH]) compared to those attached to SSCs but not in biofilms. The antimicrobial activities of biofilms formed by these isolates on SSCs against S. aureus at 25°C and 43% RH were determined. Compared to SSCs lacking biofilms formed by CE microorganisms, populations of S. aureus on SSCs harboring CE biofilms were significantly lower (P≤0.05). Results indicate that persistent antimicrobial activity against S. aureus on stainless steel surfaces can be achieved by the presence of biofilms of CE microorganisms. This information will be useful when developing strategies to improve the microbiological safety of foods during storage, processing, and distribution by facilitating the development of effective antimicrobial food-contact surfaces.

  8. A validated approach for modeling collapse of steel structures

    Science.gov (United States)

    Saykin, Vitaliy Victorovich

    shown. The calibration is performed using a particle swarm optimization algorithm to establish accurate parameters when calibrated to circumferentially notched tensile coupons. It is shown that consistent, accurate predictions are attained using the chosen models. The variation of triaxiality in steel material during plastic hardening and softening is reported. The range of triaxiality in steel structures undergoing collapse is investigated in detail and the accuracy of the chosen finite element deletion approaches is discussed. This is done through validation of different structural components and structural frames undergoing severe fracture and collapse.

  9. Automatic Weather Station (AWS) Lidar

    Science.gov (United States)

    Rall, Jonathan A.R.; Abshire, James B.; Spinhirne, James D.; Smith, David E. (Technical Monitor)

    2000-01-01

    An autonomous, low-power atmospheric lidar instrument is being developed at NASA Goddard Space Flight Center. This compact, portable lidar will operate continuously in a temperature controlled enclosure, charge its own batteries through a combination of a small rugged wind generator and solar panels, and transmit its data from remote locations to ground stations via satellite. A network of these instruments will be established by co-locating them at remote Automatic Weather Station (AWS) sites in Antarctica under the auspices of the National Science Foundation (NSF). The NSF Office of Polar Programs provides support to place the weather stations in remote areas of Antarctica in support of meteorological research and operations. The AWS meteorological data will directly benefit the analysis of the lidar data while a network of ground based atmospheric lidar will provide knowledge regarding the temporal evolution and spatial extent of Type la polar stratospheric clouds (PSC). These clouds play a crucial role in the annual austral springtime destruction of stratospheric ozone over Antarctica, i.e. the ozone hole. In addition, the lidar will monitor and record the general atmospheric conditions (transmission and backscatter) of the overlying atmosphere which will benefit the Geoscience Laser Altimeter System (GLAS). Prototype lidar instruments have been deployed to the Amundsen-Scott South Pole Station (1995-96, 2000) and to an Automated Geophysical Observatory site (AGO 1) in January 1999. We report on data acquired with these instruments, instrument performance, and anticipated performance of the AWS Lidar.

  10. Space weather and space anomalies

    Directory of Open Access Journals (Sweden)

    L. I. Dorman

    2005-11-01

    Full Text Available A large database of anomalies, registered by 220 satellites in different orbits over the period 1971-1994 has been compiled. For the first time, data from 49 Russian Kosmos satellites have been included in a statistical analysis. The database also contains a large set of daily and hourly space weather parameters. A series of statistical analyses made it possible to quantify, for different satellite orbits, space weather conditions on the days characterized by anomaly occurrences. In particular, very intense fluxes (>1000 pfu at energy >10 MeV of solar protons are linked to anomalies registered by satellites in high-altitude (>15000 km, near-polar (inclination >55° orbits typical for navigation satellites, such as those used in the GPS network, NAVSTAR, etc. (the rate of anomalies increases by a factor ~20, and to a much smaller extent to anomalies in geostationary orbits, (they increase by a factor ~4. Direct and indirect connections between anomaly occurrence and geomagnetic perturbations are also discussed.

  11. Special steel production on common carbon steel production line

    Science.gov (United States)

    Pi, Huachun; Han, Jingtao; Hu, Haiping; Bian, Ruisheng; Kang, Jianjun; Xu, Manlin

    2004-06-01

    The equipment and technology of small bar tandem rolling line of Shijiazhuang Iron & Steel Co. in China has reached the 90's international advanced level in the 20th century, but products on the line are mostly of common carbon steel. Currently there are few steel plants in China to produce 45 steel bars for cold drawing, which is a kind of shortage product. Development of 45 steel for cold drawing has a wide market outlook in China. In this paper, continuous cooling transformation (CCT) curve of 45 steel for cold drawing used for rolling was set out first. According to the CCT curve, we determined some key temperature points such as Ac3 temperature and Ac1 temperature during the cooling procedure and discussed the precipitation microstructure at different cooling rate. Then by studying thermal treatment process of 45 steel bars for cold drawing, the influence of cooling time on microstructure was analyzed and the optimum cooling speed has been found. All results concluded from the above studies are the basis of regulating controlled cooling process of 45 steel bars for cold drawing. Finally, the feasible production process of 45 steel bars for cold drawing on common carbon steel production line combined with the field condition was recommended.

  12. Prediction Techniques in Operational Space Weather Forecasting

    Science.gov (United States)

    Zhukov, Andrei

    2016-07-01

    The importance of forecasting space weather conditions is steadily increasing as our society is becoming more and more dependent on advanced technologies that may be affected by disturbed space weather. Operational space weather forecasting is still a difficult task that requires the real-time availability of input data and specific prediction techniques that are reviewed in this presentation, with an emphasis on solar and interplanetary weather. Key observations that are essential for operational space weather forecasting are listed. Predictions made on the base of empirical and statistical methods, as well as physical models, are described. Their validation, accuracy, and limitations are discussed in the context of operational forecasting. Several important problems in the scientific basis of predicting space weather are described, and possible ways to overcome them are discussed, including novel space-borne observations that could be available in future.

  13. Five case studies of multifamily weatherization programs

    Energy Technology Data Exchange (ETDEWEB)

    Kinney, L; Wilson, T.; Lewis, G. [Synertech Systems Corp. (United States); MacDonald, M. [Oak Ridge National Lab., TN (United States)

    1997-12-31

    The multifamily case studies that are the subject of this report were conducted to provide a better understanding of the approach taken by program operators in weatherizing large buildings. Because of significant variations in building construction and energy systems across the country, five states were selected based on their high level of multifamily weatherization. This report summarizes findings from case studies conducted by multifamily weatherization operations in five cities. The case studies were conducted between January and November 1994. Each of the case studies involved extensive interviews with the staff of weatherization subgrantees conducting multifamily weatherization, the inspection of 4 to 12 buildings weatherized between 1991 and 1993, and the analysis of savings and costs. The case studies focused on innovative techniques which appear to work well.

  14. Electron transfer mediators accelerated the microbiologically influence corrosion against carbon steel by nitrate reducing Pseudomonas aeruginosa biofilm.

    Science.gov (United States)

    Jia, Ru; Yang, Dongqing; Xu, Dake; Gu, Tingyue

    2017-12-01

    Electron transfer is a rate-limiting step in microbiologically influenced corrosion (MIC) caused by microbes that utilize extracellular electrons. Cross-cell wall electron transfer is necessary to transport the electrons released from extracellular iron oxidation into the cytoplasm of cells. Electron transfer mediators were found to accelerate the MIC caused by sulfate reducing bacteria. However, there is no publication in the literature showing the effect of electron transfer mediators on MIC caused by nitrate reducing bacteria (NRB). This work demonstrated that the corrosion of anaerobic Pseudomonas aeruginosa (PAO1) grown as a nitrate reducing bacterium biofilm on C1018 carbon steel was enhanced by two electron transfer mediators, riboflavin and flavin adenine dinucleotide (FAD) separately during a 7-day incubation period. The addition of either 10ppm (w/w) (26.6μM) riboflavin or 10ppm (12.7μM) FAD did not increase planktonic cell counts, but they increased the maximum pit depth on carbon steel coupons considerably from 17.5μm to 24.4μm and 25.0μm, respectively. Riboflavin and FAD also increased the specific weight loss of carbon steel from 2.06mg/cm(2) to 2.34mg/cm(2) and 2.61mg/cm(2), respectively. Linear polarization resistance, electrochemical impedance spectroscopy and potentiodynamic polarization curves all corroborated the pitting and weight loss data. Copyright © 2017 Elsevier B.V. All rights reserved.

  15. POLYTETRAFLUOROETHYLENE-RICH POLYPHENLENESULFIDE BLEND TOP COATINGS FOR MITIGATING CORROSION OF CARBON STEEL IN 300 DEGREE CELCIUS BRINE.

    Energy Technology Data Exchange (ETDEWEB)

    SUGAMA, T.; JUNG, D.

    2006-06-01

    We evaluated usefulness of a coating system consisting of an underlying polyphenylenesulfide (PPS) layer and top polytetrafluoroethylene (PTFE)-blended PPS layer as low friction, water repellent, anti-corrosion barrier film for carbon steel steam separators in geothermal power plants. The experiments were designed to obtain information on kinetic coefficient of friction, surface free energy, hydrothermal oxidation, alteration of molecular structure, thermal stability, and corrosion protection of the coating after immersing the coated carbon steel coupons for up to 35 days in CO{sub 2}-laden brine at 300 C. The superficial layer of the assembled coating was occupied by PTFE self-segregated from PPS during the melt-flowing process of this blend polymer; it conferred an outstanding slipperiness and water repellent properties because of its low friction and surface free energy. However, PTFE underwent hydrothermal oxidation in hot brine, transforming its molecular structure into an alkylated polyfluorocarboxylate salt complex linked to Na. Although such molecular transformation increased the friction and surface free energy, and also impaired the thermal stability of PTFE, the top PTFE-rich PPS layer significantly contributed to preventing the permeation of moisture and corrosive electrolytes through the coating film, so mitigating the corrosion of carbon steel.

  16. The effect of glutaraldehyde on the development of marine biofilms formed on surfaces of AISI 304 stainless steel

    Energy Technology Data Exchange (ETDEWEB)

    Tapper, R.C.; Smith, J.R.; Beech, I.B. [Univ. of Portsmouth (United Kingdom). School of Chemistry, Physics, and Radiography; Viera, M.R.; Guiamet, P.S.; Videla, H. [Univ. of La Plata (Argentina); Swords, C.L.; Edyvean, R.G.J. [Univ. of Sheffield (United Kingdom). Dept. of Mechanical and Process Engineering

    1997-08-01

    The effect of pre-conditioning polished and unpolished AISI 304 stainless steel surfaces with glutaraldehyde on the attachment, growth and morphology of an aerobic consortium of marine bacteria was investigated using total cell number counts, epifluorescence microscopy, Atomic Force Microscopy (AFM), Environmental Scanning Electron Microscopy (ESEM) and grazing-angle Fourier Transform Infrared (FTIR) spectroscopy. Both fully hydrated and dehydrated biofilms were studied using AFM and ESEM. Formation of the conditioning layer on steel surfaces from the culture medium, in the presence and absence of glutaraldehyde was monitored in-situ employing AFM and Grazing Angle FTIR spectroscopy. The influence of both surface area and surface energy upon the numbers of bacteria attached to polished and unpolished coupons was determined. This study has shown the influence of pretreatment of AISI 304 stainless steel with glutaraldehyde upon biofilm formation and has demonstrated the ability of AFM, ESEM and FTIR to be used as valuable tools for the in-situ investigation of the effect of biocides on bacterial biofilms.

  17. Space Weather and Real-Time Monitoring

    OpenAIRE

    2009-01-01

    Recent advance of information and communications technology enables to collect a large amount of ground-based and space-based observation data in real-time. The real-time data realize nowcast of space weather. This paper reports a history of space weather by the International Space Environment Service (ISES) in association with the International Geophysical Year (IGY) and importance of real-time monitoring in space weather.

  18. Extreme weather events and infectious disease outbreaks

    OpenAIRE

    McMichael, Anthony J.

    2015-01-01

    Human-driven climatic changes will fundamentally influence patterns of human health, including infectious disease clusters and epidemics following extreme weather events. Extreme weather events are projected to increase further with the advance of human-driven climate change. Both recent and historical experiences indicate that infectious disease outbreaks very often follow extreme weather events, as microbes, vectors and reservoir animal hosts exploit the disrupted social and environmental c...

  19. Space Weather and Real-Time Monitoring

    Directory of Open Access Journals (Sweden)

    S Watari

    2009-04-01

    Full Text Available Recent advance of information and communications technology enables to collect a large amount of ground-based and space-based observation data in real-time. The real-time data realize nowcast of space weather. This paper reports a history of space weather by the International Space Environment Service (ISES in association with the International Geophysical Year (IGY and importance of real-time monitoring in space weather.

  20. Spectroscopic identification of protective and non-protective corrosion coatings on steel structures in marine environments

    Energy Technology Data Exchange (ETDEWEB)

    Cook, Desmond C. [Department of Physics, Old Dominion University, Norfolk, VA 23529 (United States)]. E-mail: dcook@physics.odu.edu

    2005-10-01

    Corrosion research, and the need to fully understand the effects that environmental conditions have on the performance of structural steels, is one area in which Moessbauer spectroscopy has become a required analytical technique. This is in part due to the need to identify and quantify the nanophase iron oxides that form on and protect certain structural steels, and that are nearly transparent to most other spectroscopic techniques. In conjunction with X-ray diffraction and micro-Raman analyses, the iron oxides that form the rusts on steels corroded in different marine and other environments can be completely identified and mapped within the rust coating. The spectroscopic analyses can be used to determine the nature of the environment in which structural steels have been, and these act as a monitor of the corrosion itself. Moessbauer spectroscopy is playing an important role in a new corrosion program in the United States and Japan in which steel bridges, old and new, are being evaluated for corrosion problems that may reduce their serviceable lifetimes. Moessbauer spectroscopy has been used to characterize the corrosion products that form the protective patina on weathering steel, as well those that form in adverse environments in which the oxide coating is not adherent or protective to the steel. Moessbauer spectroscopy has also become an important analytical technique for investigating the corrosion products that have formed on archaeological artifacts, and it is providing guidance to aid in the removal of the oxides necessary for their conservation.

  1. 基于奖励券机制的输电阻塞管理方法%Transmission Congestion Management Method Based on Coupon Incentive Mechanism

    Institute of Scientific and Technical Information of China (English)

    贾曦; 钟海旺; 夏清; 丁茂生; 宁波

    2013-01-01

      In view of the demand on improving the efficiency of asset utilization, the effective transmission congestion management in smart grid becomes much more important. Under the market mechanism integrated with locational marginal price (LMP) and the background of two-level market with two-settlement in day-ahead and real-time market, it is proposed that the transmission congestion surplus should be used to mitigate the congestion of transmission lines; and combining with the characteristics of the shadow price of congested lines and demand side price elasticity coefficient, it is proposed to lead in the LMP-redispatch cost factors (L-R Factors) as the foundation of measuring the impact of LMP variation on redispatch cost of power grid. On this basis, a coupon mechanism, in which the day-ahead congestion surplus is taken as the source of funds to motivate more demand response (DR) on shifting loads between different periods and then alleviate the congestion in real-time markets, is put forward, and an effective approach for congestion management is formed. Case study based on extended IEEE 30-bus system show that both the proposed mechanism and method are effective.%  鉴于对提高资产利用效率的要求,有效的输电阻塞管理在智能电网中的重要性日益凸显。在节点边际电价和日前与实时“两级市场、两步结算”的市场背景下,提出应将输电阻塞盈余用于缓解线路阻塞,并结合阻塞线路影子价格和用户需求价格弹性系数的特性,引入节点边际价格-再调度费用影响因子,作为衡量节点价格变化对系统再调度成本影响的依据。在此基础上,提出了以日前阻塞盈余作为资金来源,激励用户主动响应、缓解实时网络阻塞状况的奖励券机制,形成了阻塞管理新的有效方法。扩展的IEEE 30节点算例表明了所提机制与方法的有效性。

  2. Compact Multi-Coupon Schemes with Concurrent Security%并发安全的紧凑多重息票方案

    Institute of Scientific and Technical Information of China (English)

    柳欣; 徐秋亮

    2012-01-01

    The disadvantage of previous multi-coupon schemes is the lack of efficient protocol in which users can decide the maximal number of redemption according to their demands.And another deficiency is thai they cannot remain secure in the concurrent case.This article remedied these obstacles by providing two improved systems with concurrent security.The first scheme was obtained by extending the underlying scheme of Blanton with the proof of two committed values and the Sigma-compiler for two round concurrent zero-knowledge argument.The second scheme (i.e.,the strengthened version of the first one) achieved more efficient security reduction by incorporating the straight-line extraction paradigm and removed random oracles by using the non-interactive zero-knowledge argument from homomorphic encryption.Compared with the other strongly unsplittable schemes,the first scheme has better communicational efficiency and the second one does not rely on the random oracle model.%已有多重息票方案的弱点是缺乏支持用户根据需要选择最大兑换数量的高效协议.另一个缺陷是并不满足并发安全性.为了克服这些困难,提出两个并发安全的改进方案.第一个方案是利用关于两个被承诺值的知识证明和2轮并发零知识论证的Sigma协议编译器对底层的Blanton方案进行扩展得到的.第二个方案(即前一个方案的增强版本)利用直线提取技术实现了更为高效的安全性归约过程,并借助基于同态加密的非交互零知识论证避免了对随机预言机的使用.与其他的强不可分割的方案相比,第一个方案具有更高的通信效率,且第二个方案的安全性并不依赖于随机预言模型.

  3. History of ultrahigh carbon steels

    Energy Technology Data Exchange (ETDEWEB)

    Wadsworth, J.; Sherby, O.D.

    1997-06-20

    The history and development of ultrahigh carbon steels (i.e., steels containing between 1 and 2.l percent C and now known as UHCS) are described. The early use of steel compositions containing carbon contents above the eutectoid level is found in ancient weapons from around the world. For example, both Damascus and Japanese sword steels are hypereutectoid steels. Their manufacture and processing is of interest in understanding the role of carbon content in the development of modern steels. Although sporadic examples of UHCS compositions are found in steels examined in the early part of this century, it was not until the mid-1970s that the modern study began. This study had its origin in the development of superplastic behavior in steels and the recognition that increasing the carbon content was of importance in developing that property. The compositions that were optimal for superplasticity involved the development of steels that contained higher carbon contents than conventional modern steels. It was discovered, however, that the room temperature properties of these compositions were of interest in their own right. Following this discovery, a period of intense work began on understanding their manufacture, processing, and properties for both superplastic forming and room temperature applications. The development of superplastic cast irons and iron carbides, as well as those of laminated composites containing UHCS, was an important part of this history.

  4. Traffic Control Under Complex Weather Conditions in Suining Airport

    Institute of Scientific and Technical Information of China (English)

    吕维峰

    2014-01-01

    Complex weather conditions is meaning thunderstorm freezing turbulence wind-shear low visibility weather affect the flight safety. When confronted with complex weather conditions,the controllers should know the weather condition and trend weather,and notify the aircraft under your control zone.The controllers provide the required services to the pilots,help the pilots to avoid the complex weather.In this paper, through different complex weathers under different control command,get the different methods of control.

  5. 46 CFR 59.20-1 - Carbon-steel or alloy-steel castings.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 2 2010-10-01 2010-10-01 false Carbon-steel or alloy-steel castings. 59.20-1 Section 59... BOILERS, PRESSURE VESSELS AND APPURTENANCES Welding Repairs to Castings § 59.20-1 Carbon-steel or alloy-steel castings. Defects in carbon-steel or alloy-steel castings may be repaired by welding. The...

  6. Weather Satellite Enterprise Information Chain

    Science.gov (United States)

    Jamilkowski, M. L.; Grant, K. D.; Miller, S. W.; Cochran, S.

    2015-12-01

    NOAA & NASA are acquiring the next-generation civilian operational weather satellite: Joint Polar Satellite System (JPSS). Contributing the afternoon orbit & ground system (GS) to replace current NOAA POES Satellites, its sensors will collect meteorological, oceanographic & climatological data. The JPSS Common Ground System (CGS), consisting of C3 and IDP segments, is developed by Raytheon. It now flies the Suomi National Polar-orbiting Partnership (S-NPP) satellite, transferring data between ground facilities, processing them into environmental products for NOAA weather centers, and expanding to support JPSS-1 in 2017. As a multi-mission system, CGS provides combinations of C3, data processing, and product delivery for numerous NASA, NOAA, DoD and international missions.The CGS provides a wide range of support to a number of missions: Command and control and mission management for the S-NPP mission today, expanding this support to the JPSS-1 satellite mission in 2017 Data acquisition for S-NPP, the JAXA's Global Change Observation Mission - Water (GCOM-W1), POES, and the Defense Meteorological Satellite Program (DMSP) and Coriolis/WindSat for the DoD Data routing over a global fiber network for S-NPP, JPSS-1, GCOM-W1, POES, DMSP, Coriolis/WindSat, NASA EOS missions, MetOp for EUMETSAT and the National Science Foundation Environmental data processing and distribution for S-NPP, GCOM-W1 and JPSS-1 The CGS plays a key role in facilitating the movement and value-added enhancement of data all the way from satellite-based sensor data to delivery to the consumers who generate forecasts and produce watches and warnings. This presentation will discuss the information flow from sensors, through data routing and processing, and finally to product delivery. It will highlight how advances in architecture developed through lessons learned from S-NPP and implemented for JPSS-1 will increase data availability and reduce latency for end user applications.

  7. Weather pattern climatology of the United States

    Energy Technology Data Exchange (ETDEWEB)

    Barchet, W.R.; Davis, W.E.

    1984-01-01

    In this study the geographic domain covered the 48 conterminous states of the United States. The daily synoptic weather pattern was classified into nine types for the 10-year period January 1, 1969 to December 31, 1978. Weather pattern types were defined relative to the classical polar front model of a mid-latitude cyclonic storm system and its associated air masses. Guidelines for classifying weather patterns on an operational basis were developed. These were applied to 3652 daily surface weather maps to produce a time series of weather pattern type at 120 grid points of a 160 point, 3/sup 0/ latitude by 4/sup 0/ longitude array over the United States. Statistics on the frequency of occurrence, persistence and alternation of weather patterns were calculated for each grid point. Summary statistics for the entire grid and for six regions were also presented. Frequency of occurrence and persistence were found to depend on the size and speed of movement of the weather pattern. Large, slow moving air masses had higher frequency of occurrence and longer persistence than small (fronts) or rapidly moving (or changing) features (fronts, storm centers). Some types showed distinct regional preferences. The subtropical maritime high occurred mainly in the south central and southeast. An indeterminate weather pattern type accounted for those weather patterns that did not fit the polar front model or were too disorganized to be classified. The intermountain thermal low of the desert southwest was one such feature that dominated both frequency of occurrence and persistence in this region. Alternation from one weather pattern to another followed the polar front model of a moving cyclonic storm. The tendency for anticyclonic weather patterns to become disorganized as they weakened was seen in the high percentage of these patterns that changed to an indeterminate pattern as they aged.

  8. The Application of Synoptic Weather Forecasting Rules to Selected Weather Situations in the United States.

    Science.gov (United States)

    Kohler, Fred E.

    The document describes the use of weather maps and data in teaching introductory college courses in synoptic meteorology. Students examine weather changes at three-hour intervals from data obtained from the "Monthly Summary of Local Climatological Data." Weather variables in the local summary include sky cover, air temperature, dew point, relative…

  9. Hedging Weather Risk for Corn Production in Northeastern China: The Efficiency of Weather-indexed Insurance

    NARCIS (Netherlands)

    Sun, Baojing; Guo, Changhao; Kooten, van G.C.

    2014-01-01

    Purpose – The paper analyzes the hedging efficiency of weather-indexed insurance for corn production in Northeast of China. The purpose of this paper is to identify the potential weather variables that impact corn yields and to analyze the efficiency of weather-indexed insurance under varying

  10. Coated 4340 Steel

    Science.gov (United States)

    2013-08-26

    alternative coatings qualified to MIL-PRE-23377 Class N and an electroplated zinc - nickel alloy passivated with a trivalent chromium solution which is...effect of a non-chromate primer and zinc - nickel plating with non-chromate passivation as alternatives to the chromate primer and cadmium plating with...NAWCADPAX/TR-2013/252 COATED 4340 STEEL by E. U. Lee C. Lei M. Stanley B. Pregger C. Matzdorf 26 August 2013

  11. Ferrium M54 Steel

    Science.gov (United States)

    2015-03-18

    Examination ................................................................................................. 2 Zinc - Nickel Alloy Plating...resistance measurements using scans from 100 mV below to 100mV above at a scan rate of 0.167 mV/s. ZINC - NICKEL ALLOY PLATING The Zn-14% Ni alloy...release; distribution is unlimited. 13. SUPPLEMENTARY NOTES 14. ABSTRACT Bare and Zn-14% Ni alloy coated Ferrium M54 steels were studied to

  12. Fracture Mechanisms in Steel Castings

    Directory of Open Access Journals (Sweden)

    Z. Stradomski

    2013-07-01

    Full Text Available The investigations were inspired with the problem of cracking of steel castings during the production process. A single mechanism of decohesion - the intergranular one - occurs in the case of hot cracking, while a variety of structural factors is decisive for hot cracking initiation, depending on chemical composition of the cast steel. The low-carbon and low-alloyed steel castings crack due to the presence of the type II sulphides, the cause of cracking of the high-carbon tool cast steels is the net of secondary cementite and/or ledeburite precipitated along the boundaries of solidified grains. Also the brittle phosphor and carbide eutectics precipitated in the final stage solidification are responsible for cracking of castings made of Hadfield steel. The examination of mechanical properties at 1050°C revealed low or very low strength of high-carbon cast steels.

  13. PHOSPHORUS REMOVAL USING STEEL SLAG

    Institute of Scientific and Technical Information of China (English)

    Y.Z. Lan; S. Zhang; J.K. Wang; R. W. Smith

    2006-01-01

    Steel slag is a byproduct produced in large amounts in the steel-making process. It is an important resource that can be effectively utilized. An experiment was described in which steel slag was tested as an adsorbent for the removal of phosphorus from waste water. Phosphorus removal depended on the amount of steel slag added, the pH value, the contact time, and the initial concentration. Under laboratory conditions when the added slag was 7.5g/L, the contact time 2h, and the pH value was equivalent to 6.5, over 99% of the phosphorus was removed; the experimental data on steel slag adsorption of phosphorus in the water fitted the Freundlich isotherm model. Steel slag was found to be very effective in adsorbing phosphorus.

  14. Mechanics in Steels through Microscopy

    OpenAIRE

    Tirumalasetty, G. K.

    2013-01-01

    The goal of the study consolidated in this thesis is to understand the mechanics in steels using microscopy. In particular, the mechanical response of Transformation Induced Plasticity (TRIP) steels is correlated with their microstructures. Chapter 1 introduces the current state of the art of TRIP steels, highlighting the importance of microstructure - mechanical properties - applications relationships. In Chapter 2 the material properties and material processing are described into more detai...

  15. Output Model of Steel Plant

    Institute of Scientific and Technical Information of China (English)

    ZHANG Long-qiang; TIAN Nai-yuan; ZHANG Jin; XU An-jun

    2008-01-01

    Based on the requirement of compactivity, continuity, and high efficiency, and taking full advantage of cushion capability of flexible parts such as external refining in new generation steel plant, an output model of steel plant was established in terms of matching between BOF and caster. Using this model, the BOF nominal capacity is selected, the caster output and equipment amount are computed, and then the steel plant output is computed.

  16. Medium-range fire weather forecasts

    Science.gov (United States)

    J.O. Roads; K. Ueyoshi; S.C. Chen; J. Alpert; F. Fujioka

    1991-01-01

    The forecast skill of theNational Meteorological Center's medium range forecast (MRF) numerical forecasts of fire weather variables is assessed for the period June 1,1988 to May 31,1990. Near-surface virtual temperature, relative humidity, wind speed and a derived fire weather index (FWI) are forecast well by the MRF model. However, forecast relative humidity has...

  17. Uncertainty analysis of weather controlled systems

    NARCIS (Netherlands)

    Keesman, K.J.; Doeswijk, T.G.

    2010-01-01

    The indoor climate of many storage facilities for agricultural produce is controlled by mixing ambient air with the air flow through the store room. Hence, the indoor climate is affected by the ambient weather conditions. Given hourly fluctuating energy tariffs, weather forecasts over some days are

  18. Uncertainty analysis of weather controlled systems

    NARCIS (Netherlands)

    Keesman, K.J.; Doeswijk, T.G.

    2010-01-01

    The indoor climate of many storage facilities for agricultural produce is controlled by mixing ambient air with the air flow through the store room. Hence, the indoor climate is affected by the ambient weather conditions. Given hourly fluctuating energy tariffs, weather forecasts over some days are

  19. Adaptive Weather Forecasting using Local Meteorological Information

    NARCIS (Netherlands)

    Doeswijk, T.G.; Keesman, K.J.

    2005-01-01

    In general, meteorological parameters such as temperature, rain and global radiation are important for agricultural systems. Anticipating on future conditions is most often needed in these systems. Weather forecasts then become of substantial importance. As weather forecasts are subject to uncertain

  20. The Early Years: About the Weather

    Science.gov (United States)

    Ashbrook, Peggy

    2015-01-01

    Observing and documenting elements of weather teach children about using tools and their senses to learn about the environment. This column discusses resources and science topics related to students in grades preK to 2. This month's issue describes an activity where students indirectly document local weather by counting outdoor clothing types worn…

  1. Extreme weather events and infectious disease outbreaks.

    Science.gov (United States)

    McMichael, Anthony J

    2015-01-01

    Human-driven climatic changes will fundamentally influence patterns of human health, including infectious disease clusters and epidemics following extreme weather events. Extreme weather events are projected to increase further with the advance of human-driven climate change. Both recent and historical experiences indicate that infectious disease outbreaks very often follow extreme weather events, as microbes, vectors and reservoir animal hosts exploit the disrupted social and environmental conditions of extreme weather events. This review article examines infectious disease risks associated with extreme weather events; it draws on recent experiences including Hurricane Katrina in 2005 and the 2010 Pakistan mega-floods, and historical examples from previous centuries of epidemics and 'pestilence' associated with extreme weather disasters and climatic changes. A fuller understanding of climatic change, the precursors and triggers of extreme weather events and health consequences is needed in order to anticipate and respond to the infectious disease risks associated with human-driven climate change. Post-event risks to human health can be constrained, nonetheless, by reducing background rates of persistent infection, preparatory action such as coordinated disease surveillance and vaccination coverage, and strengthened disaster response. In the face of changing climate and weather conditions, it is critically important to think in ecological terms about the determinants of health, disease and death in human populations.

  2. AWE: Aviation Weather Data Visualization Environment

    Science.gov (United States)

    Spirkovska, Lilly; Lodha, Suresh K.; Norvig, Peter (Technical Monitor)

    2000-01-01

    Weather is one of the major causes of aviation accidents. General aviation (GA) flights account for 92% of all the aviation accidents, In spite of all the official and unofficial sources of weather visualization tools available to pilots, there is an urgent need for visualizing several weather related data tailored for general aviation pilots. Our system, Aviation Weather Data Visualization Environment AWE), presents graphical displays of meteorological observations, terminal area forecasts, and winds aloft forecasts onto a cartographic grid specific to the pilot's area of interest. Decisions regarding the graphical display and design are made based on careful consideration of user needs. Integral visual display of these elements of weather reports is designed for the use of GA pilots as a weather briefing and route selection tool. AWE provides linking of the weather information to the flight's path and schedule. The pilot can interact with the system to obtain aviation-specific weather for the entire area or for his specific route to explore what-if scenarios and make "go/no-go" decisions. The system, as evaluated by some pilots at NASA Ames Research Center, was found to be useful.

  3. 再生水用于循环冷却水中铁细菌对碳钢腐蚀的影响%Influence of iron-oxidizing bacteria in reclaimed water used for recycle cooling water on corrosion behavior of carbon steel

    Institute of Scientific and Technical Information of China (English)

    吴卿; 李云; 李亚男; 田一梅; 彭森

    2014-01-01

    以再生水用于循环冷却水系统中铁细菌的生长特性和其对碳钢腐蚀的影响为研究目标,采用电化学手段研究铁细菌对碳钢腐蚀的影响,应用环境扫描电镜分析碳钢挂片腐蚀的表面形貌特征,并进行EDS能谱分析。结果表明:循环冷却水中铁细菌生长所需要的最佳碳源和氮源分别为柠檬酸铁铵和NaNO3;铁细菌生长过程中开路电位和极化电阻先正移再负移最后保持不变;由于生物膜分布不均匀,挂片表面会产生球状和层状两种元素组分存在明显差异的腐蚀结构;铁细菌的参与可明显影响碳钢挂片的元素成分含量,使金属的腐蚀加重。%The growth characteristics of iron-oxidizing bacteria (IOB) in reclaimed water used for recycle cooling water and its influence on the corrosion behavior of carbon steel were studied. Electrochemical methods were used to study the influence of IOB on carbon steel′s corrosion behavior. The morphology changes of carbon steel coupons sur-face were researched by observing with the environmental scanning electron microscope(ESEM) and chemical el-ement changes of those carbon steel coupons were analyzed by energy diffraction spectrum (EDS). The results showed that the optimum carbon source and nitrogen source of IOB were ferric ammonium citrate and NaNO3, re-spectively. The results of electrochemical test indicated that both of open circuit potential and polarization resis-tance increased at the beginning and then declined, and finally they remained unchanged in the presence of IOB. Due to the uneven distribution of biofilm, there were two different surface structures on coupons, which were spherical structure and sheet structure with different elemental compositions. The participation of IOB can signifi-cantly affect the elemental composition and concentration of steel coupons, and can increase the corrosion of the metal.

  4. Learn about Earth Science: Weather. [CD-ROM].

    Science.gov (United States)

    2000

    This CD-ROM, designed for students in grades K-2, explores the world of weather. Students investigate weather to learn about climate and the seasons, how animals adapt to weather changes, how clouds tell us about conditions, and how weather plays a part in our everyday lives. The weather calendar lets students record and write about conditions…

  5. Tough Year Ahead for Steel

    Institute of Scientific and Technical Information of China (English)

    REN WEI

    2006-01-01

    @@ The steel industry, a top beneficiary of the country's sizzling economic growth, is this year likely to see only a meager profit or even report losses, according to a report by the National Development and Reform Commission. Mounting demand for steel in real estate construction and auto making during the past years resulted in an investment craze into the sector, and has caused a glut on the market. Average steel prices fell by a third last year, though domestic steel makers still managed to post a profit of 127.4 billion yuan (US$15.9 billion) on aggregate.

  6. High strength, tough alloy steel

    Science.gov (United States)

    Thomas, Gareth; Rao, Bangaru V. N.

    1979-01-01

    A high strength, tough alloy steel is formed by heating the steel to a temperature in the austenite range (1000.degree.-1100.degree. C.) to form a homogeneous austenite phase and then cooling the steel to form a microstructure of uniformly dispersed dislocated martensite separated by continuous thin boundary films of stabilized retained austenite. The steel includes 0.2-0.35 weight % carbon, at least 1% and preferably 3-4.5% chromium, and at least one other substitutional alloying element, preferably manganese or nickel. The austenite film is stable to subsequent heat treatment as by tempering (below 300.degree. C.) and reforms to a stable film after austenite grain refinement.

  7. Hydrogen Embrittlement of Gun Steel

    Science.gov (United States)

    1987-11-01

    8217s HY80 and HY130 steels were checked for the critical hydrogen concentrations which were determined to be 6 ppm for HY8O steel 8 and 3 ppm for HY130...JOTC FILE COPY AD-A188 972 AD 1 TECHNICAL REPORT ARCCB-TR-87030 HYDROGEN EMBRITTLEMENT OF GUN STEEL F’ GERALD L. SPFNCER DTIC DEC 1 5 1987 NOVEMBER...PtEtIOC COVERED HYDROGEN EMBRITTLEHENT OF GUN STEEL Final OG EOTNME 6. PERFORMINGORO EOTNME 7. A*JTNOR(s) S. CONTRACT OR GRANT NUMBER(&) Gerald L

  8. Pushing the Envelope of Extreme Space Weather

    Science.gov (United States)

    Pesnell, W. D.

    2014-12-01

    Extreme Space Weather events are large solar flares or geomagnetic storms, which can cost billions of dollars to recover from. We have few examples of such events; the Carrington Event (the solar superstorm) is one of the few that had superlatives in three categories: size of solar flare, drop in Dst, and amplitude of aa. Kepler observations show that stars similar to the Sun can have flares releasing millions of times more energy than an X-class flare. These flares and the accompanying coronal mass ejections could strongly affect the atmosphere surrounding a planet. What level of solar activity would be necessary to strongly affect the atmosphere of the Earth? Can we map out the envelope of space weather along the evolution of the Sun? What would space weather look like if the Sun stopped producing a magnetic field? To what extreme should Space Weather go? These are the extremes of Space Weather explored in this talk.

  9. Space weather: European Space Agency perspectives

    Science.gov (United States)

    Daly, E. J.; Hilgers, A.

    Spacecraft and payloads have become steadily more sophisticated and therefore more susceptible to space weather effects. ESA has long been active in applying models and tools to the problems associated with such effects on its spacecraft. In parallel, ESA and European agencies have built a highly successful solar-terrestrial physics capability. ESA is now investigating the marriage of these technological and scientific capabilities to address perceived user needs for space weather products and services. Two major ESA-sponsored studies are laying the groundwork for a possible operational European space weather service. The wide-ranging activities of ESA in the Space Weather/Space Environment domain are summarized and recent important examples of space weather concerns given.

  10. Weatherization works: Final report of the National Weatherization Evaluation

    Energy Technology Data Exchange (ETDEWEB)

    Brown, M.A.; Berry, L.G.; Kinney, L.F.

    1994-09-01

    In 1990, the U.S. Department of Energy (DOE) sponsored a comprehensive evaluation of its Weatherization Assistance Program, the nation`s largest residential energy conservation program. Oak Ridge National Laboratory (ORNL) managed the five-part study. This document summarizes the findings of the evaluation. Its conclusions are based mainly on data from the 1989 program year (supplemented by data from 1991-92). The evaluation concludes that the Program meets the objectives of its enabling legislation and fulfills its mission statement. Specifically, it (1) saves energy, (2) lowers fuel bills, and (3) improves the health and safety of dwellings occupied by low-income people. In addition, the Program achieves its mission in a cost-effective manner based on each of three perspectives employed by the evaluators. Finally, the evaluation estimates that the investments made in 1989 will, over a 20-year lifetime, save the equivalent of 12 million barrels of oil, roughly the amount of oil added to the Strategic Petroleum Reserve in each of the past several years.

  11. Long term weathering effects on the thermal performance of the solaron (air) solar collector

    Science.gov (United States)

    1979-01-01

    The test procedures and the results obtained during the evaluation test program on the Solaron Corporation air-type solar collector are presented. The tests were performed under simulated conditions, following long-term exposure to natural weathering conditions. The Solaron Model 2001, air-type solar collector has a gross area of 19 square feet and the weight is 160 pounds. The absorber plate is made of 24-gage steel, the coating is baked-on black paint, the cover consists of two sheets of 1/8-inch low-iron tempered glass, and the insulation is one thickness of 3 5/8-inch fiberglass batting.

  12. Using Music to Communicate Weather and Climate

    Science.gov (United States)

    Williams, P.; Aplin, K. L.; Brown, S.; Jenkins, K.; Mander, S.; Walsh, C.

    2016-12-01

    Depictions of weather and other atmospheric phenomena are common throughout the arts. Unlike in the visual arts, however, there has been little study of meteorological inspiration in music. This presentation will discuss the frequencies with which different weather types have been depicted in music over time, covering the period from the seventeenth century to the present day. Beginning with classical orchestral music, we find that composers were generally influenced by their own country's climate in the type of weather they chose to represent. Depictions of weather vary from explicit mimicry using traditional and specialized orchestral instruments, through to subtle suggestions. Pieces depicting stormy weather tend to be in minor keys, whereas pieces depicting fair weather tend to be in major keys. As befits the national stereotype, British composers seem disproportionately keen to depict the UK's variable weather patterns and stormy coastline. Moving onto modern popular music, we have identified and analyzed over 750 songs referring to different weather types. We find that lyrical references to bad weather peaked in songs written during the stormy 1950s and 60s, when there were many hurricanes, before declining in the relatively calm 1970s and 80s. This finding again suggests a causal link between song-writers' meteorological environments and compositional outputs. Composers and song-writers have a unique ability to emotionally connect their listeners to the environment. This ability could be exploited to communicate environmental science to a broader audience. Our work provides a catalogue of cultural responses to weather before (and during the early stages of) climate change. The effects of global warming may influence musical expression in future, in which case our work will provide a baseline for comparison.

  13. Evolution of the Spectral Emissivity and Phase Transformations of the Al-Si Coating on Usibor® 1500P Steel During Austenitization

    Science.gov (United States)

    Shi, Cangji; Daun, Kyle J.; Wells, Mary A.

    2016-08-01

    Usibor® 1500P coupons are austenitized in a Gleeble 3500 thermomechanical simulator using a two-step heating procedure in an argon atmosphere. Variations in spectral emissivity are measured in-situ using a near infrared spectrometer and ex situ with a Fourier transform infrared reflectometer. Microstructural evolution and surface roughness are investigated using optical microscopy, FE-scanning electron microscopy, and a surface profilometer. A series of phase transformations of Al-Fe-Si intermetallic phases at the coating/steel substrate interface cause the surface phase and surface roughness to change, which in turn influences the spectral emissivity. At the beginning of the first heating step, the coupons have very low spectral emissivity, due to the molten Al-Si coating. Spectral emissivity increases significantly with increasing soak time from 5 to 12 minutes, associated with the surface phase transformation of the coating into Al7Fe2Si intermetallic phase and an increase in surface roughness. Through the second step heating at 1173 K (900 °C), the spectral emissivity shows a gradually decreasing trend with increasing soak time, caused by the surface phase transformation from Al5Fe2 into AlFe intermetallic phase with a decrease in surface roughness.

  14. Evolution of the Spectral Emissivity and Phase Transformations of the Al-Si Coating on Usibor® 1500P Steel During Austenitization

    Science.gov (United States)

    Shi, Cangji; Daun, Kyle J.; Wells, Mary A.

    2016-12-01

    Usibor® 1500P coupons are austenitized in a Gleeble 3500 thermomechanical simulator using a two-step heating procedure in an argon atmosphere. Variations in spectral emissivity are measured in-situ using a near infrared spectrometer and ex situ with a Fourier transform infrared reflectometer. Microstructural evolution and surface roughness are investigated using optical microscopy, FE-scanning electron microscopy, and a surface profilometer. A series of phase transformations of Al-Fe-Si intermetallic phases at the coating/steel substrate interface cause the surface phase and surface roughness to change, which in turn influences the spectral emissivity. At the beginning of the first heating step, the coupons have very low spectral emissivity, due to the molten Al-Si coating. Spectral emissivity increases significantly with increasing soak time from 5 to 12 minutes, associated with the surface phase transformation of the coating into Al7Fe2Si intermetallic phase and an increase in surface roughness. Through the second step heating at 1173 K (900 °C), the spectral emissivity shows a gradually decreasing trend with increasing soak time, caused by the surface phase transformation from Al5Fe2 into AlFe intermetallic phase with a decrease in surface roughness.

  15. Alaska Native Weatherization Training and Jobs Program First Steps Toward Tribal Weatherization – Human Capacity Development

    Energy Technology Data Exchange (ETDEWEB)

    Wiita, Joanne

    2013-07-30

    The Alaska Native Weatherization Training and Jobs Project expanded weatherization services for tribal members’ homes in southeast Alaska while providing weatherization training and on the job training (OJT) for tribal citizens that lead to jobs and most probably careers in weatherization-related occupations. The program resulted in; (a) 80 Alaska Native citizens provided with skills training in five weatherization training units that were delivered in cooperation with University of Alaska Southeast, in accordance with the U.S. Department of Energy Core Competencies for Weatherization Training that prepared participants for employment in three weatherizationrelated occupations: Installer, Crew Chief, and Auditor; (b) 25 paid OJT training opportunities for trainees who successfully completed the training course; and (c) employed trained personnel that have begun to rehab on over 1,000 housing units for weatherization.

  16. A Century of Monitoring Weather and Crops: The Weekly Weather and Crop Bulletin.

    Science.gov (United States)

    Heddinghaus, Thomas R.; Le Comte, Douglas M.

    1992-02-01

    Publication of a national weekly weather summary called the Weekly Weather Chronicle began in 1872. This summary was the precursor of today's Weekly Weather and Crop Bulletin (WWCB), a publication that reports global weather and climate conditions relevant to agricultural interests, as well as current national activities and assessments of crop and livestock conditions. The WWCB is produced by the Joint Agricultural Weather Facility (JAWF), a world agricultural weather information center located in the U.S. Department of Agriculture (USDA) headquarters in Washington, D.C., and jointly staffed by units of the National Oceanic and Atmospheric Administration's Climats. Analysis Center and USDA's World Agricultural Outlook Board and National Agricultural Statistics Service. Besides featuring charts and tables (e.g., temperature and precipitation maps and crop progress and condition tables), the WWCB contains summaries and special stories highlighting significant weather events affecting agriculture, such as droughts, torrential rains, floods, unusual warmth, heat waves, severe freezes, heavy snowfall, blizzards, damaging storms, and hurricanes.

  17. Forecasting Space Weather from Magnetograms

    Science.gov (United States)

    Falconer, David A.; Moore, Ronald L.; Barghouty, Abdulnasser F.; Khazanov, Igor

    2012-01-01

    Large flares and fast CMEs are the drivers of the most severe space weather including Solar Energetic Particle Events (SEP Events). Large flares and their co-produced CMEs are powered by the explosive release of free magnetic energy stored in non-potential magnetic fields of sunspot active regions. The free energy is stored in and released from the low-beta regime of the active region s magnetic field above the photosphere, in the chromosphere and low corona. From our work over the past decade and from similar work of several other groups, it is now well established that (1) a proxy of the free magnetic energy stored above the photosphere can be measured from photospheric magnetograms, maps of the measured field in the photosphere, and (2) an active region s rate of production of major CME/flare eruptions in the coming day or so is strongly correlated with its present measured value of the free-energy proxy. These results have led us to use the large database of SOHO/MDI full-disk magnetograms spanning Solar Cycle 23 to obtain empirical forecasting curves that from an active region s present measured value of the free-energy proxy give the active region s expected rates of production of major flares, CMEs, fast CMEs, and SEP Events in the coming day or so (Falconer et al 2011, Space Weather, 9, S04003). For each type of event, the expected rate is readily converted to the chance that the active region will produce such an event in any given forward time window of a day or so. If the chance is small enough (e.g. <5%), the forecast is All Clear for that type of event. We will present these forecasting curves and demonstrate the accuracy of their forecasts. In addition, we will show that the forecasts for major flares and fast CMEs can be made significantly more accurate by taking into account not only the value of the free energy proxy but also the active region s recent productivity of major flares; specifically, whether the active region has produced a major flare

  18. Adhesion and biocides inactivation of Salmonella on stainless steel and polyethylene

    Directory of Open Access Journals (Sweden)

    Eduardo Cesar Tondo

    2010-12-01

    Full Text Available The adhesion of Salmonella (S. strains to stainless steel and polyethylene and their inactivation by biocides used in food industry was investigated. Coupons of stainless steel and polyethylene were immersed in bacterial suspensions of S. Enteritidis, S. Typhimurium, and S. Bredeney during 15, 30, and 60 minutes, and submitted to different concentrations of peracetic acid (PAA, sodium hypochlorite (NaOCl, and quaternary ammonium (Quat sanitizers. Hydrophobicity of the surfaces was evaluated by contact angle measurements using the sessile drop method and bacterial adhesion was accompanied through bacterial counts and scanning electron microscopy (SEM. Results indicated that the three serovars of Salmonella presented similar adhesion to both materials (5.0 to 6.5 log cfu cm-2. The time of exposure did not influence the counts of adhered cells on both surfaces, however SEM revealed larger clusters of S. Enteritidis on both materials, not found for the other serovars. S. Enteritidis presented lower sessile drop angle on polyethylene, indicating hydrophilic properties of this material. The biocides were not able to inactivate all the microorganisms adhered on both surfaces. At least 1 log cfu cm-2 of all serovars tested remained viable after the exposure to different biocide concentrations. In general, higher counts of survivors were observed on polyethylene disinfected with different concentrations of biocides. S. Bredeney e S. Typhimurium were more resistant than S. Enteritidis to PAA, whilst S. Enteritidis presented smaller reduction rates to NaOCl. This last biocide was able to reduce Salmonella counts in approximately 3.0 to 4.0 log cm-2. When adhered to polyethylene, the serovars S. Typhimurium and S. Enteritidis were more resistant to Quat than S. Bredeney in all concentrations tested, and the numbers of S. Enteritidis remained almost unaltered. On stainless steel disinfected by Quat, S. Bredeney presented higher numbers of survivors.

  19. Milled Die Steel Surface Roughness Correlation with Steel Sheet Friction

    DEFF Research Database (Denmark)

    Berglund, J.; Brown, C.A.; Rosén, B.-G.

    2010-01-01

    This work investigates correlations between the surface topography ofmilled steel dies and friction with steel sheet. Several die surfaces were prepared by milling. Friction was measured in bending under tension testing. Linear regression coefficients (R2) between the friction and texture...

  20. Weather Station and Sensor Locations, MDTA Roadway weather station, weather stations, weather sensors, Roadway weather sensors, RWIS, MDTA weather sensors, Published in 2009, 1:1200 (1in=100ft) scale, Maryland Transportation Authority.

    Data.gov (United States)

    NSGIC GIS Inventory (aka Ramona) — This Weather Station and Sensor Locations dataset, published at 1:1200 (1in=100ft) scale, was produced all or in part from Hardcopy Maps information as of 2009. It...

  1. Weather Information Communications (WINCOMM) Project: Dissemination of Weather Information for the Reduction of Aviation Weather-Related Accident Causal Factors

    Science.gov (United States)

    Jarrell, Michael; Tanger, Thomas

    2004-01-01

    Weather Information Communications (WINCOMM) is part of the Weather Accident Prevention (WxAP) Project, which is part of the NASA's Aviation Safety and Security Program. The goals of WINCOMM are to facilitate the exchange of tactical and strategic weather information between air and ground. This viewgraph presentation provides information on data link decision factors, architectures, validation goals. WINCOMM is capable of providing en-route communication air-to-ground, ground-to-air, and air-to-air, even on international or intercontinental flights. The presentation also includes information on the capacity, cost, and development of data links.

  2. On-line data acquisition system for Aanderaa weather station

    Digital Repository Service at National Institute of Oceanography (India)

    AshokKumar, K.; Diwan, S.G.

    Aanderaa Weather Station can be installed at unattended remote places for collection of various weather parameters at regular preselected intervals. The weather parameters are recorded on the magnetic spool inside a battery operated datalogger which...

  3. Operational, regional-scale, chemical weather forecasting models in Europe

    NARCIS (Netherlands)

    Kukkonen, J.; Balk, T.; Schultz, D.M.; Baklanov, A.; Klein, T.; Miranda, A.I.; Monteiro, A.; Hirtl, M.; Tarvainen, V.; Boy, M.; Peuch, V.H.; Poupkou, A.; Kioutsioukis, I.; Finardi, S.; Sofiev, M.; Sokhi, R.; Lehtinen, K.; Karatzas, K.; San José, R.; Astitha, M.; Kallos, G.; Schaap, M.; Reimer, E.; Jakobs, H.; Eben, K.

    2011-01-01

    Numerical models that combine weather forecasting and atmospheric chemistry are here referred to as chemical weather forecasting models. Eighteen operational chemical weather forecasting models on regional and continental scales in Europe are described and compared in this article. Topics discussed

  4. Weatherization Works: Final Report of the National Weatherization Evaluation

    Energy Technology Data Exchange (ETDEWEB)

    Brown, M.A.

    2001-02-01

    In 1990, the US Department of Energy (DOE) sponsored a comprehensive evaluation of its Weatherization Assistance Program, the nation's largest residential energy conservation program. Oak Ridge National Laboratory (ORNL) managed the five-part study. This document summarizes the findings of the evaluation. Its conclusions are based mainly on data from the 1989 program year. The evaluation concludes that the Program meets the objectives of its enabling legislation and fulfills its mission statement. Specifically, it saves energy, lowers fuel bills, and improves the health and safety of dwellings occupied by low-income people. In addition, the Program achieves its mission in a cost-effective manner based on each of three perspectives employed by the evaluators. Finally, the evaluation estimates that the investments made in 1989 will, over a 20-year lifetime, save the equivalent of 12 million barrels of oil, roughly the amount of oil added to the Strategic Petroleum Reserve in each of the past several years. The Program's mission is to reduce the heating and cooling costs for low-income families--particularly the elderly, persons with disabilities, and children by improving the energy efficiency of their homes and ensuring their health and safety. Substantial progress has been made, but the job is far from over. The Department of Health and Human Services (HHS) reports that the average low-income family spends 12 percent of its income on residential energy, compared to only 3% for the average-income family. Homes where low-income families live also have a greater need for energy efficiency improvements, but less money to pay for them.

  5. Determination and analysis of the physical chemical characteristics of witness coupons of boral for the CNLV; Determinacion y analisis de las caracteristicas fisico quimicas de cupones testigo de boral para la CNLV

    Energy Technology Data Exchange (ETDEWEB)

    Gonzalez M, J.L.; Aguilar H, F.; Rivero G, T.; Carrillo M, R. [ININ, Apdo. Post 18-1027, Col Escandon, 11801 Mexico D.F. (Mexico)]. E-mail: jlgm@nuclear.inin.mx; fah@nuclear.inin.mx; trg@nuclear.inin.mx; racm@nuclear.inin.mx

    2004-07-01

    The burnt fuel elements that are extracted in each charging of the Units 1 and 2 of the Nuclear Power Plant of Laguna Verde, are deposited in shelves placed in the storage reservoir designed for this end. Each cell or storage shelf has a structure type cage. Among the cells neutron absorber material is placed, (Boral), what allows to avoid the possible criticality that could settle down when accumulating in the storage the irradiated fuel elements. This boral has been designed to maintain its characteristics of thermal neutron absorber during a lifetime of the plant. To check that the wings and the Boral have not suffered some degradation or some change due to the environmental conditions in the warehouse, it is necessary to watch over their physical and chemical characteristics periodically, what is carried out by a surveillance program based on Badges or manufactured witness coupons of the same material that the wings. The badges witness are embedded in a special wing, which is placed in the place with more radiation in the pool. In this work the laboratory tests carried out in the ININ to the coupon witness 03 of the Unit 2, (II-03) are described, being presented the results and obtained conclusions. (Author)

  6. MEASURING SYSTEM OF ADVERSE WEATHER PHENOMENA

    Directory of Open Access Journals (Sweden)

    M. Ćurić

    2012-03-01

    Full Text Available Measuring system of adverse weather phenomena. The adverse weather phenomena in nowadays are becoming an extraordinary problem in human life and human activity. Therefore, it seems very important to know the thresholds of adverse weather phenomena. These thresholds can be calculated in different ways, but some experience has shown that for weather elements which departures from normal follow the normal distribution suits to use the Gaussian curve of frequency distribution (temperature and pressure. For such weather elements the normal curve of frequency distribution may be used for classification of thresholds. For weather elements which departures do not depend on such a frequency distribution configuration (precipitation amounts may be used a decile method. For wind speed thresholds, the Beaufort scale units can be used for calculation. In this paper the threshold scales for four basic weather elemnts are presented. All these scales contain four steps each. They are defined: normal, above normal, much above normal and extraordinary above normal or normal, below normal, much below normal and extraordinary below normal. The examples by observations of Meteorological Observatory in Belgrade are presented.

  7. Steel designers' handbook

    CERN Document Server

    Gorenc, Branko; Tinyou, Ron

    2012-01-01

    The Revised 7th Edition of Steel Designers' Handbook is an invaluable tool for all practising structural, civil and mechanical engineers as well as engineering students at university and TAFE in Australia and New Zealand. It has been prepared in response to changes in the design Standard AS 4100, the structural Design Actions Standards, AS /ANZ 1170, other processing Standards such as welding and coatings, updated research as well as feedback from users. This edition is based on Australian Standard (AS) 4100: 1998 and subsequent amendments. The worked numerical examples in the book have been e

  8. The Integrated Space Weather Analysis System

    Science.gov (United States)

    Maddox, M. M.; Hesse, M.; Kuznetsova, M.; Rastaetter, L.; MacNeice, P. J.; Jain, P.; Garneau, J. W.; Berrios, D. H.; Pulkinnen, A.; Rowland, D.

    2008-12-01

    Space weather affects virtually all of NASA's endeavors, from robotic missions to human exploration. Knowledge and prediction of space weather conditions is therefore essential to NASA operations. The diverse nature of currently available space environment measurements and modeling products, along with the lack of single-portal access, renders its practical use for space weather analysis and forecasting unfeasible. There exists a compelling need for accurate real-time forecasting of both large-scale and local space environments - and their probable impacts for missions. A vital design driver for any system that is created to solve this problem lies in the fact that information needs to be presented in a form that is useful and as such, must be both easily accessible and understandable. The Integrated Space Weather Analysis System is a joint development project at NASA GSFC between the Space Weather Laboratory, Community Coordinated Modeling Center, Applied Engineering & Technology Directorate, and NASA HQ Office Of Chief Engineer. The iSWA system will be a turnkey, web-based dissemination system for NASA-relevant space weather information that combines forecasts based on the most advanced space weather models with concurrent space environment information. It will be customer configurable and adaptable for use as a powerful decision making tool offering an unprecedented ability to analyze the present and expected future space weather impacts on virtually all NASA human and robotic missions. We will discuss some of the key design considerations for the system and present some of the initial space weather analysis products that have been created to date.

  9. The industrial ecology of steel

    Energy Technology Data Exchange (ETDEWEB)

    Considine, Timothy J.; Jablonowski, Christopher; Considine, Donita M.M.; Rao, Prasad G.

    2001-03-26

    This study performs an integrated assessment of new technology adoption in the steel industry. New coke, iron, and steel production technologies are discussed, and their economic and environmental characteristics are compared. Based upon detailed plant level data on cost and physical input-output relations by process, this study develops a simple mathematical optimization model of steel process choice. This model is then expanded to a life cycle context, accounting for environmental emissions generated during the production and transportation of energy and material inputs into steelmaking. This life-cycle optimization model provides a basis for evaluating the environmental impacts of existing and new iron and steel technologies. Five different plant configurations are examined, from conventional integrated steel production to completely scrap-based operations. Two cost criteria are used to evaluate technology choice: private and social cost, with the latter including the environmental damages associated with emissions. While scrap-based technologies clearly generate lower emissions in mass terms, their emissions of sulfur dioxide and nitrogen oxides are significantly higher. Using conventional damage cost estimates reported in the literature suggests that the social costs associated with scrap-based steel production are slightly higher than with integrated steel production. This suggests that adopting a life-cycle viewpoint can substantially affect environmental assessment of new technologies. Finally, this study also examines the impacts of carbon taxes on steel production costs and technology choice.

  10. Mechanics in Steels through Microscopy

    NARCIS (Netherlands)

    Tirumalasetty, G.K.

    2013-01-01

    The goal of the study consolidated in this thesis is to understand the mechanics in steels using microscopy. In particular, the mechanical response of Transformation Induced Plasticity (TRIP) steels is correlated with their microstructures. Chapter 1 introduces the current state of the art of TRIP s

  11. Mechanics in Steels through Microscopy

    NARCIS (Netherlands)

    Tirumalasetty, G.K.

    2013-01-01

    The goal of the study consolidated in this thesis is to understand the mechanics in steels using microscopy. In particular, the mechanical response of Transformation Induced Plasticity (TRIP) steels is correlated with their microstructures. Chapter 1 introduces the current state of the art of TRIP

  12. CORROSION INHIBITOR FOR CARBON STEELS

    African Journals Online (AJOL)

    corrosion inhibitor for carbon steel in 3% ac]neon.s' NaCl solution (pH 6) ... compared to stainless steels (Buchweishaija & Hagen 1997). Organic compounds are ... resistant dust for break and clutch linings, wood binders and mould (Gedam.

  13. Hydrogen Embrittlement of Structural Steels

    Energy Technology Data Exchange (ETDEWEB)

    Somerday, Brian P.; San Marchi, Christopher W

    2014-08-01

    Carbon-manganese steels are candidates for the structural materials in hydrogen gas pipelines; however, it is well known that these steels are susceptible to hydrogen embrittlement. Decades of research and industrial experience have established that hydrogen embrittlement compromises the structural integrity of steel components. This experience has also helped identify the failure modes that can operate in hydrogen containment structures. As a result, there are tangible ideas for managing hydrogen embrittlement in steels and quantifying safety margins for steel hydrogen containment structures. For example, fatigue crack growth aided by hydrogen embrittlement is a well-established failure mode for steel hydrogen containment structures subjected to pressure cycling. This pressure cycling represents one of the key differences in operating conditions between current hydrogen pipelines and those anticipated in a hydrogen delivery infrastructure. Applying structural integrity models in design codes coupled with measurement of relevant material properties allows quantification of the reliability/integrity of steel hydrogen pipelines subjected to pressure cycling. Furthermore, application of these structural integrity models is aided by the development of physics-based predictive models, which provide important insights such as the effects of microstructure on hydrogen-assisted fatigue crack growth. Successful implementation of these structural integrity and physics-based models enhances confidence in the design codes and enables decisions about materials selection and operating conditions for reliable and efficient steel hydrogen pipelines.

  14. Great Challenge in Steel Export

    Institute of Scientific and Technical Information of China (English)

    Charlsea Liu

    2009-01-01

    @@ In 2008, the export of China steel products experienoeu, a splendid period f fast growing, and then disappointedly followed by fast depression. Until lest December, China in 2008 exported steel products of 59.21 million tons, less than the same term in 2007 by 3.48 million tons, declining about 5.6%.

  15. Steels from materials science to structural engineering

    CERN Document Server

    Sha, Wei

    2013-01-01

    Steels and computer-based modelling are fast growing fields in materials science as well as structural engineering, demonstrated by the large amount of recent literature. Steels: From Materials Science to Structural Engineering combines steels research and model development, including the application of modelling techniques in steels.  The latest research includes structural engineering modelling, and novel, prototype alloy steels such as heat-resistant steel, nitride-strengthened ferritic/martensitic steel and low nickel maraging steel.  Researchers studying steels will find the topics vital to their work.  Materials experts will be able to learn about steels used in structural engineering as well as modelling and apply this increasingly important technique in their steel materials research and development. 

  16. Weather station with a web server

    OpenAIRE

    Repinc, Matej

    2013-01-01

    In this diploma thesis we present the process of making a cheap weather station using Arduino prototyping platform and its functionality. The weather station monitors current temperature, humidity of air and air pressure. The station has its own simple HTTP server that is used to relay current data in two different formats: JSON encoded data and simple HTML website. The weather station can also send data to a pre-defined server used for data collection. We implemented a web site where data an...

  17. The quiet revolution of numerical weather prediction

    Science.gov (United States)

    Bauer, Peter; Thorpe, Alan; Brunet, Gilbert

    2015-09-01

    Advances in numerical weather prediction represent a quiet revolution because they have resulted from a steady accumulation of scientific knowledge and technological advances over many years that, with only a few exceptions, have not been associated with the aura of fundamental physics breakthroughs. Nonetheless, the impact of numerical weather prediction is among the greatest of any area of physical science. As a computational problem, global weather prediction is comparable to the simulation of the human brain and of the evolution of the early Universe, and it is performed every day at major operational centres across the world.

  18. Space weather and coronal mass ejections

    CERN Document Server

    Howard, Tim

    2013-01-01

    Space weather has attracted a lot of attention in recent times. Severe space weather can disrupt spacecraft, and on Earth can be the cause of power outages and power station failure. It also presents a radiation hazard for airline passengers and astronauts. These ""magnetic storms"" are most commonly caused by coronal mass ejections, or CMES, which are large eruptions of plasma and magnetic field from the Sun that can reach speeds of several thousand km/s. In this SpringerBrief, Space Weather and Coronal Mass Ejections, author Timothy Howard briefly introduces the coronal mass ejection, its sc

  19. PRESIDENT MUSHARRAF: All Weather Friendship Keeps Rising

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    @@ Tangible Suggestions on Promoting All Weather Bilateral Trade I would first of all like to extend warm greetings from the people of Pakistan to the people of China on the 55th year of all weather friendship between our two countries and this all weather friendship will keep rising. Succeeding generations in both countries have ever since carefully nurtured this friendship which has blossomed into beautiful and all comprehensive partnership for peace and development. Pakistan China friendship is rooted in the ethos of our peoples.It evokes spontaneous love, respect, admiration and touches a receptive cord in every heart that resonates and energizes this unique relationship.

  20. NASA GSFC Space Weather Center - Innovative Space Weather Dissemination: Web-Interfaces, Mobile Applications, and More

    Science.gov (United States)

    Maddox, Marlo; Zheng, Yihua; Rastaetter, Lutz; Taktakishvili, A.; Mays, M. L.; Kuznetsova, M.; Lee, Hyesook; Chulaki, Anna; Hesse, Michael; Mullinix, Richard; hide

    2012-01-01

    The NASA GSFC Space Weather Center (http://swc.gsfc.nasa.gov) is committed to providing forecasts, alerts, research, and educational support to address NASA's space weather needs - in addition to the needs of the general space weather community. We provide a host of services including spacecraft anomaly resolution, historical impact analysis, real-time monitoring and forecasting, custom space weather alerts and products, weekly summaries and reports, and most recently - video casts. There are many challenges in providing accurate descriptions of past, present, and expected space weather events - and the Space Weather Center at NASA GSFC employs several innovative solutions to provide access to a comprehensive collection of both observational data, as well as space weather model/simulation data. We'll describe the challenges we've faced with managing hundreds of data streams, running models in real-time, data storage, and data dissemination. We'll also highlight several systems and tools that are utilized by the Space Weather Center in our daily operations, all of which are available to the general community as well. These systems and services include a web-based application called the Integrated Space Weather Analysis System (iSWA http://iswa.gsfc.nasa.gov), two mobile space weather applications for both IOS and Android devices, an external API for web-service style access to data, google earth compatible data products, and a downloadable client-based visualization tool.

  1. Powernext weather, benchmark indices for effective weather risk management; Powernext Weather, des indices de reference pour gerer le risque meteo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2006-07-01

    According to the U.S. Department of Energy, an estimated 25% of the GNP is affected by weather-related events. The variations in temperature - even small ones - can also have long-lasting effects on the operational results of a company. Among other, the Energy supply sector is sensitive to weather risks: a milder or harsher than usual winter leads to a decrease or increase of energy consumption. The price of electricity on power trading facilities like Powernext is especially sensitive to odd changes in temperatures. Powernext and Meteo-France (the French meteorological agency) have joined expertise in order to promote the use of weather indices in term of decision making or underlying of hedging tools to energy actors, end users from any other sector of activity and specialists of the weather risk hedging. The Powernext Weather indices are made from information collected by Meteo-France's main observation network according to the norms of international meteorology, in areas carefully selected. The gross data are submitted to a thorough review allowing the correction of abnormalities and the reconstitution of missing data. Each index is fashioned to take into account the economic activity in the various regions of the country as represented by each region's population. This demographic information represents a fair approximation of the weight of the regional economic activity. This document presents the Powernext/Meteo France partnership for the elaboration of efficient weather-related risk management indices. (J.S.)

  2. Nanoprecipitation in bearing steels

    Energy Technology Data Exchange (ETDEWEB)

    Barrow, A.T.W. [SKF University Technology Centre, Department of Materials Science and Metallurgy, University of Cambridge, Cambridge CB2 3QZ (United Kingdom); Rivera-Diaz-del-Castillo, P.E.J., E-mail: pejr2@cam.ac.uk [SKF University Technology Centre, Department of Materials Science and Metallurgy, University of Cambridge, Cambridge CB2 3QZ (United Kingdom)

    2011-11-15

    {theta}-phase is the main hardening species in bearing steels and appears in both martensitically and bainitically hardened microstructures. This work presents a survey of the microstrucural features accompanying nanoprecipitation in bearing steels. Nanoprecipitate structures formed in 1C-1.5Cr wt.% with additions of Cr, Mn, Mo, Si and Ni are studied. The work is combined with thermodynamic calculations and neural networks to predict the expected matrix composition, and whether this will transform martensitically or bainitically. Martensite tetragonality, composition and the amount of retained austenite are related to hardness and the type of nanoprecipitate structures in martensitic grades. The {theta}-phase volume fraction, the duration of the bainite to austenite transformation and the amount of retained austenite are related to hardness and a detailed quantitative description of the precipitate nanostructures. Such description includes compositional studies using energy-dispersive spectroscopy, which shows that nanoprecipitate formation takes place under paraequilibrium. Special attention is devoted to a novel two-step bainite tempering process which shows maximum hardness; we prove that this is the most effective process for incorporating solute into the precipitates, which are finer than those resulting from one-step banitic transformation processes.

  3. Impact of Tactical and Strategic Weather Avoidance on Separation Assurance

    Science.gov (United States)

    Refai, Mohamad S.; Windhorst, Robert

    2011-01-01

    The ability to keep flights away from weather hazards while maintaining aircraft-to-aircraft separation is critically important. The Advanced Airspace Concept is an automation concept that implements a ground-based strategic conflict resolution algorithm for management of aircraft separation. The impact of dynamic and uncertain weather avoidance on this concept is investigated. A strategic weather rerouting system is integrated with the Advanced Airspace Concept, which also provides a tactical weather avoidance algorithm, in a fast time simulation of the Air Transportation System. Strategic weather rerouting is used to plan routes around weather in the 20 minute to two-hour time horizon. To address forecast uncertainty, flight routes are revised at 15 minute intervals. Tactical weather avoidance is used for short term trajectory adjustments (30 minute planning horizon) that are updated every minute to address any weather conflicts (instances where aircraft are predicted to pass through weather cells) that are left unresolved by strategic weather rerouting. The fast time simulation is used to assess the impact of tactical weather avoidance on the performance of automated conflict resolution as well as the impact of strategic weather rerouting on both conflict resolution and tactical weather avoidance. The results demonstrate that both tactical weather avoidance and strategic weather rerouting increase the algorithm complexity required to find aircraft conflict resolutions. Results also demonstrate that tactical weather avoidance is prone to higher airborne delay than strategic weather rerouting. Adding strategic weather rerouting to tactical weather avoidance reduces total airborne delays for the reported scenario by 18% and reduces the number of remaining weather violations by 13%. Finally, two features are identified that have proven important for strategic weather rerouting to realize these benefits; namely, the ability to revise reroutes and the use of maneuvers

  4. Study on Snow-Melting System around Steel Top of Underground Fire Cistern using Heat Pipe

    Science.gov (United States)

    Nagai, Niro; Nakano, Norimasa; Takeuchi, Masanori; Maekawa, Yoshitaka; Maegawa, Yoshikazu

    This research aims to develop snow melting system around steel top of underground fire cistern by using heat pipe, for realizing quick finding of the steel top under heavy snow fall. Water in a fire cistern installed underground is heated by underground heat source, 10 ~15 °C. The iron top is put on snow melting panel made of reinforced concrete. Heat is transported from water to the snow melting panel by heat pipes, which melts snow on it. The experimental results obtained for two years show that this system can melt the snow around the steel top in winter season preferably. The numerical simulation using only weather data was found to predict temperature variations of the whole system with good agreements to the experimental data. Therefore, this simulation software can be used for designing this snow-melting system.

  5. Optimization Design of Thermal Conduction Enhanced PCM Plates for Simulating the Infrared Signature of Steel Plate

    Institute of Scientific and Technical Information of China (English)

    YE Hong; JIANG Li-feng

    2008-01-01

    Phase change material (PCM) can be used to prepare the infrared false targets for realizing all-weather passive infrared decoy, but its low thermal conductivity is a great blockage to the simulation of the infrared signature of thick metal plates. For that reason, a method of simulating the infrared signature of thick steel plates by thermal conduction enhanced PCM, including the aluminum fins, is proposed. A physical and mathematic model is set up, and the infrared signature simulation of thick steel plate is investigated numerically. The effects of the distribution density and thickness of fins and the thickness of PCM plate on the simulation results are discussed, and the reasonable construction parameters of PCM plates used to simulate the steel plates of different thickness are obtained.

  6. Influence of the steel scrap classes on the liquid steel output molten in electric steel processes

    Directory of Open Access Journals (Sweden)

    K. Janiszewski

    2012-12-01

    Full Text Available Purpose: This is why we have analysed in the paper, using statistical analysing methods, the influence of use in the electric arc furnace charges of steel scrap of different qualities on the index of liquid steel output from a melt.Design/methodology/approach: The used research methodology consists in analytical simulation of variations in mass of liquid steel obtained from melts differing in steel scrap content in the metallic charge and statistical analyses of industrial results acquired from the corresponding process documentation (so called melt cards.Findings: Basing on the analytical and statistical analyses carried out we have determine resulting variations in the liquid steel per melt ratios depending on the content of steel scrap in the metallic charge.Research limitations/implications: The research results obtained can be utilized in each steelmaking facility, which employs the Electric Steelmaking process, in order to “design” the metallic charge compositions, having in view the quality and economic aspects.Practical implications: The research results presented in the paper can be used for steel production of high purity steels.Originality/value: The results presented in this paper are directed to the steelmakers employing the Electric Steelmaking process and constitute the authors’ original study.

  7. National Ignition Facility wet weather construction plan

    Energy Technology Data Exchange (ETDEWEB)

    Kugler, A N

    1998-01-01

    This report presents a wet weather construction plan for the National Ignition Facility (NIF) construction project. Construction of the NIF commenced in mid- 1997, and excavation of the site was completed in the fall. Preparations for placing concrete foundations began in the fall, and above normal rainfall is expected over the tinter. Heavy rainfall in late November impacted foundation construction, and a wet weather construction plan was determined to be needed. This wet weather constiction plan recommends a strategy, techniques and management practices to prepare and protect the site corn wet weather effects and allow construction work to proceed. It is intended that information in this plan be incorporated in the Stormwater Pollution Prevention Plan (SWPPP) as warranted.

  8. Improving Local Weather Forecasts for Agricultural Applications

    NARCIS (Netherlands)

    Doeswijk, T.G.; Keesman, K.J.

    2005-01-01

    For controlling agricultural systems, weather forecasts can be of substantial importance. Studies have shown that forecast errors can be reduced in terms of bias and standard deviation using forecasts and meteorological measurements from one specific meteorological station. For agricultural systems

  9. Space weather research and forecast in USA

    CERN Document Server

    Pevtsov, Alexei A

    2016-01-01

    In the United States, scientific research in space weather is funded by several Government Agencies including the National Science Foundation (NSF) and the National Aeronautics and Space Agency (NASA). For commercial purposes, space weather forecast is made by the Space Weather Prediction Center (SWPC) of the National Oceanic and Atmospheric Administration (NOAA). Observations come from the network of groundbased observatories funded via various sources, as well as from the instruments on spacecraft. Numerical models used in forecast are developed in the framework of individual research projects. Later, the most promising models are selected for additional testing at SWPC. In order to increase the application of models in research and education, NASA in collaboration with other agencies created Community Coordinated Modeling Center (CCMC). In mid-1990, US scientific community presented compelling evidence for developing the National Program on Space Weather, and in 1995, such program has been formally created...

  10. Improving Local Weather Forecasts for Agricultural Applications

    NARCIS (Netherlands)

    Doeswijk, T.G.; Keesman, K.J.

    2005-01-01

    For controlling agricultural systems, weather forecasts can be of substantial importance. Studies have shown that forecast errors can be reduced in terms of bias and standard deviation using forecasts and meteorological measurements from one specific meteorological station. For agricultural systems

  11. Europe's First Space Weather Think Tank

    Science.gov (United States)

    Lilensten, Jean; Clark, Toby; Belehaki, Anna

    2004-04-01

    A new European intergovernmental action devoted to space weather has been recently approved. This paper describes the political and scientific context in which this action takes place, and the goals of this action, called COST 724.

  12. The fate of chromium during tropical weathering

    DEFF Research Database (Denmark)

    Berger, Alfons; Frei, Robert

    2014-01-01

    . The negatively fractionated δ53Cr values measured in the weathering profile relative to the unaltered tonalitic bedrock characterized by a high temperature magmatic inventory Cr isotope signature are consistent with loss of a positively fractionated Cr(VI) pool formed during weathering. The predicted existence......We performed a mineral, geochemical and Cr–Sr–Pb isotope study on a laterite profile developed on ca. 540 Ma old tonalitic bedrock in Madagascar with special emphasis on the behavior of chromium during tropical weathering. The observed strong depletions of Ca, Si, and P, and enrichment of Fe and Al...... of the soil profile relative to stage one altered saprolite. This gain in Cr is accompanied by decreasing δ53Cr values and can be explained by partial immobilization (possibly by adsorption/coprecipitation on/with Fe-oxy-hydroxides) of mobile Cr(III) during upward transport in the weathering profile...

  13. CRADE OF SAND AND DUST STORM WEATHER

    Institute of Scientific and Technical Information of China (English)

    Niu Ruoyun; Tian Cuiying; Bi Baogui; Yang Keming; Wang Youheng; Tuo Ya; Ding Haifang; Zhang Tairen

    2011-01-01

    Background Sand and dust storm,as one of the main disastrous weathers that affect northern China,not only affect the people health and normal life,but cause the short-term climatic changes due to the direct and indirect radiation of the earth-atmosphere system through the dust floating in the sky.The sand end dust weather and its potential harm on the national economy,ecological environment,social activities and other aspects have aroused worldwide concern.

  14. Space Weather Gets Real—on Smartphones

    Science.gov (United States)

    Tobiska, W. Kent; Crowley, Geoff; Oh, Seung Jun; Guhathakurta, Madhulika

    2010-10-01

    True to the saying that "a picture is worth a thousand words," society's affinity for visual images has driven innovative efforts to see space weather as it happens. The newest frontiers of these efforts involve applications, or apps, on cellular phones, allowing space weather researchers, operators, and teachers, as well as other interested parties, to have the ability to monitor conditions in real time with just the touch of a button.

  15. Key findings of the national weatherization evaluation

    Energy Technology Data Exchange (ETDEWEB)

    Brown, M.A.; Berry, L.G.

    1994-10-01

    In 1990, the U.S. Department of Energy sponsored a comprehensive evaluation of its Weatherization Assistance Program, the nation`s largest residential energy conservation program. The primary goal of the evaluation was to establish whether the Program meets the objectives of its enabling legislation and fulfills its mission statement, to reduce the heating and cooling costs for low-income families-particularly the elderly, persons with disabilities, and children by improving the energy-efficiency of their homes and ensuring their health and safety. Oak Ridge National Laboratory managed a five-part study which produced a series of documents evaluating the Program. The objective of this document is to summarize the findings of the five-part National Weatherization Evaluation. The five studies were as follows: (1) Network Study-this study characterized the weatherization network`s leveraging, capabilities, procedures, staff, technologies, and innovations; (2) Resources and Population Study-this study profiled low-income weatherization resources, the weatherized population, and the population remaining to be served; (3) Multifamily Study-this study described the nature and extent of weatherization activities in larger multifamily buildings; (4) Single-family Study-this study estimated the national savings and cost- effectiveness of weatherizing single-family and small multifamily dwellings that use natural gas or electricity for space heating; (5) Fuel-Oil Study-this study estimated the savings and cost-effectiveness of weatherizing single-family homes, located in nine northeastern states, that use fuel oil for space heating. This paper provides a brief overview of each study`s purposes, research methods and most important findings.

  16. Dew architectures - Dew annouces the good weather

    OpenAIRE

    Beysens, Daniel; Broggini, Filippo; Milimouk-Melnytchouk, Iryna; Ouazzani, Jalil; Tixier, Nicolas

    2012-01-01

    International audience; Dew is a natural phenomenon that occurs under particular weather conditions (clear nocturnal sky, humid air, low wind) and on a surface specially designed for this purpose (high radiative cooling properties, special architectural design). Depending on the weather conditions and the surface characteristics, the water yield can give up to 0.7 litres per square meter and per night. Although the collection of rain water on roof turns out to be relatively simple, dew harves...

  17. Climate change and extreme events in weather

    Digital Repository Service at National Institute of Oceanography (India)

    RameshKumar, M.R.

    monsoon and b) tropical cyclones. Basically the climate of India is domi- nated by the south west monsoon season which accounts for about 75% of the annual rainfall. The extreme weather events occur over India are: Floods, Droughts, Tropical Cyclones..., Heat Waves and Cold Waves, Storms Surges, Hail Storms, Thunderstorms, Dust Storms. Floods, droughts and tropical cyclones have specific significance a far as India is concerned. Floods and droughts are the two sides of the weather phenomena...

  18. Topographic imprint on chemical weathering in deeply weathered soil-mantled landscapes (southern Brazil)

    Science.gov (United States)

    Vanacker, Veerle; Schoonejans, Jerome; Ameijeiras-Marino, Yolanda; Opfergelt, Sophie; Minella, Jean

    2017-04-01

    The regolith mantle is defined as the thin layer of unconsolidated material overlaying bedrock that contributes to shape the Earth's surface. The development of the regolith mantle in a landscape is the result of in-situ weathering, atmospheric input and downhill transport of weathering products. Bedrock weathering - the physical and chemical transformations of rock to soil - contributes to the vertical development of the regolith layer through downward propagation of the weathering front. Lateral transport of soil particles, aggregates and solutes by diffusive and concentrated particle and solute fluxes result in lateral redistribution of weathering products over the hillslope. In this study, we aim to expand the empirical basis on long-term soil evolution at the landscape scale through a detailed study of soil weathering in subtropical soils. Spatial variability in chemical mass fluxes and weathering intensity were studied along two toposequences with similar climate, lithology and vegetation but different slope morphology. This allowed us to isolate the topographic imprint on chemical weathering and soil development. The toposequences have convexo-concave slope morphology, and eight regolith profiles were analysed involving the flat upslope, steep midslope and flat toeslope part. Our data show a clear topographic imprint on soil development. Along hillslope, the chemical weathering intensity of the regolith profiles increases with distance from the crest. In contrast to the upslope positions, the soils in the basal concavities develop on in-situ and transported regolith. While the chemical weathering extent on the slope convexities (the upslope profiles) is similar for the steep and gentle toposequence, there is a clear difference in the rate of increase of the chemical weathering extent with distance from the crest. The increase of chemical weathering extent along hillslope is highest for the steep toposequence, suggesting that topography enhances soil particle

  19. Seasonal Forecasting of Fire Weather Based on a New Global Fire Weather Database

    Science.gov (United States)

    Dowdy, Andrew J.; Field, Robert D.; Spessa, Allan C.

    2016-01-01

    Seasonal forecasting of fire weather is examined based on a recently produced global database of the Fire Weather Index (FWI) system beginning in 1980. Seasonal average values of the FWI are examined in relation to measures of the El Nino-Southern Oscillation (ENSO) and the Indian Ocean Dipole (IOD). The results are used to examine seasonal forecasts of fire weather conditions throughout the world.

  20. Improving the toughness of ultrahigh strength steel

    Energy Technology Data Exchange (ETDEWEB)

    Soto, Koji

    2002-08-15

    The ideal structural steel combines high strength with high fracture toughness. This dissertation discusses the toughening mechanism of the Fe/Co/Ni/Cr/Mo/C steel, AerMet 100, which has the highest toughness/strength combination among all commercial ultrahigh strength steels. The possibility of improving the toughness of this steel was examined by considering several relevant factors.

  1. 49 CFR 192.55 - Steel pipe.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 3 2010-10-01 2010-10-01 false Steel pipe. 192.55 Section 192.55 Transportation... BY PIPELINE: MINIMUM FEDERAL SAFETY STANDARDS Materials § 192.55 Steel pipe. (a) New steel pipe is... in accordance with paragraph (c) or (d) of this section. (b) Used steel pipe is qualified for use...

  2. Introducing GFWED: The Global Fire Weather Database

    Science.gov (United States)

    Field, R. D.; Spessa, A. C.; Aziz, N. A.; Camia, A.; Cantin, A.; Carr, R.; de Groot, W. J.; Dowdy, A. J.; Flannigan, M. D.; Manomaiphiboon, K.; Pappenberger, F.; Tanpipat, V.; Wang, X.

    2015-01-01

    The Canadian Forest Fire Weather Index (FWI) System is the mostly widely used fire danger rating system in the world. We have developed a global database of daily FWI System calculations, beginning in 1980, called the Global Fire WEather Database (GFWED) gridded to a spatial resolution of 0.5 latitude by 2-3 longitude. Input weather data were obtained from the NASA Modern Era Retrospective-Analysis for Research and Applications (MERRA), and two different estimates of daily precipitation from rain gauges over land. FWI System Drought Code calculations from the gridded data sets were compared to calculations from individual weather station data for a representative set of 48 stations in North, Central and South America, Europe, Russia,Southeast Asia and Australia. Agreement between gridded calculations and the station-based calculations tended to be most different at low latitudes for strictly MERRA based calculations. Strong biases could be seen in either direction: MERRA DC over the Mato Grosso in Brazil reached unrealistically high values exceeding DCD1500 during the dry season but was too low over Southeast Asia during the dry season. These biases are consistent with those previously identified in MERRAs precipitation, and they reinforce the need to consider alternative sources of precipitation data. GFWED can be used for analyzing historical relationships between fire weather and fire activity at continental and global scales, in identifying large-scale atmosphereocean controls on fire weather, and calibration of FWI-based fire prediction models.

  3. Development of a Global Fire Weather Database

    Science.gov (United States)

    Field, R. D.; Spessa, A. C.; Aziz, N. A.; Camia, A.; Cantin, A.; Carr, R.; de Groot, W. J.; Dowdy, A. J.; Flannigan, M. D.; Manomaiphiboon, K.; Pappenberger, F.; Tanpipat, V.; Wang, X.

    2015-06-01

    The Canadian Forest Fire Weather Index (FWI) System is the mostly widely used fire danger rating system in the world. We have developed a global database of daily FWI System calculations, beginning in 1980, called the Global Fire WEather Database (GFWED) gridded to a spatial resolution of 0.5° latitude by 2/3° longitude. Input weather data were obtained from the NASA Modern Era Retrospective-Analysis for Research and Applications (MERRA), and two different estimates of daily precipitation from rain gauges over land. FWI System Drought Code calculations from the gridded data sets were compared to calculations from individual weather station data for a representative set of 48 stations in North, Central and South America, Europe, Russia, Southeast Asia and Australia. Agreement between gridded calculations and the station-based calculations tended to be most different at low latitudes for strictly MERRA-based calculations. Strong biases could be seen in either direction: MERRA DC over the Mato Grosso in Brazil reached unrealistically high values exceeding DC = 1500 during the dry season but was too low over Southeast Asia during the dry season. These biases are consistent with those previously identified in MERRA's precipitation, and they reinforce the need to consider alternative sources of precipitation data. GFWED can be used for analyzing historical relationships between fire weather and fire activity at continental and global scales, in identifying large-scale atmosphere-ocean controls on fire weather, and calibration of FWI-based fire prediction models.

  4. Operational Space Weather in USAF Education

    Science.gov (United States)

    Smithtro, C.; Quigley, S.

    2006-12-01

    Most education programs offering space weather courses are understandably and traditionally heavily weighted with theoretical space physics that is the basis for most of what is researched and modeled. While understanding the theory is a good and necessary grounding for anyone working the field of space weather, few military or commercial jobs employ such theory in real-time operations. The operations sites/centers are much more geared toward use of applied theory-resultant models, tools and products. To ensure its operations centers personnel, commanders, real-time system operators and other customers affected by the space environment are educated on available and soon-to-be operational space weather models and products, the USAF has developed applicable course/lecture material taught at various institutions to include the Air Force Institute of Technology (AFIT) and the Joint Weather Training Complex (335th/TRS/OUA). Less frequent training of operational space weather is available via other venues that will be discussed, and associated course material is also being developed for potential use at the National Security Space Institute (NSSI). This presentation provides an overview of the programs, locations, courses and material developed and/or taught by or for USAF personnel dealing with operational space weather. It also provides general information on student research project results that may be used in operational support, along with observations regarding logistical and professional benefits of teaching such non-theoretical/non-traditional material.

  5. Flight Deck Weather Avoidance Decision Support: Implementation and Evaluation

    Science.gov (United States)

    Wu, Shu-Chieh; Luna, Rocio; Johnson, Walter W.

    2013-01-01

    Weather related disruptions account for seventy percent of the delays in the National Airspace System (NAS). A key component in the weather plan of the Next Generation of Air Transportation System (NextGen) is to assimilate observed weather information and probabilistic forecasts into the decision process of flight crews and air traffic controllers. In this research we explore supporting flight crew weather decision making through the development of a flight deck predicted weather display system that utilizes weather predictions generated by ground-based radar. This system integrates and presents this weather information, together with in-flight trajectory modification tools, within a cockpit display of traffic information (CDTI) prototype. that the CDTI features 2D and perspective 3D visualization models of weather. The weather forecast products that we implemented were the Corridor Integrated Weather System (CIWS) and the Convective Weather Avoidance Model (CWAM), both developed by MIT Lincoln Lab. We evaluated the use of CIWS and CWAM for flight deck weather avoidance in two part-task experiments. Experiment 1 compared pilots' en route weather avoidance performance in four weather information conditions that differed in the type and amount of predicted forecast (CIWS current weather only, CIWS current and historical weather, CIWS current and forecast weather, CIWS current and forecast weather and CWAM predictions). Experiment 2 compared the use of perspective 3D and 21/2D presentations of weather for flight deck weather avoidance. Results showed that pilots could take advantage of longer range predicted weather forecasts in performing en route weather avoidance but more research will be needed to determine what combinations of information are optimal and how best to present them.

  6. CCMC: Serving research and space weather communities with unique space weather services, innovative tools and resources

    Science.gov (United States)

    Zheng, Yihua; Kuznetsova, Maria M.; Pulkkinen, Antti; Maddox, Marlo

    2015-04-01

    With the addition of Space Weather Research Center (a sub-team within CCMC) in 2010 to address NASA’s own space weather needs, CCMC has become a unique entity that not only facilitates research through providing access to the state-of-the-art space science and space weather models, but also plays a critical role in providing unique space weather services to NASA robotic missions, developing innovative tools and transitioning research to operations via user feedback. With scientists, forecasters and software developers working together within one team, through close and direct connection with space weather customers and trusted relationship with model developers, CCMC is flexible, nimble and effective to meet customer needs. In this presentation, we highlight a few unique aspects of CCMC/SWRC’s space weather services, such as addressing space weather throughout the solar system, pushing the frontier of space weather forecasting via the ensemble approach, providing direct personnel and tool support for spacecraft anomaly resolution, prompting development of multi-purpose tools and knowledge bases, and educating and engaging the next generation of space weather scientists.

  7. The scope of the Weatherization Assistance Program: The weatherized population and the resource base

    Energy Technology Data Exchange (ETDEWEB)

    Power, M.; Eisenberg, J.F.; Michels, E. [Economic Opportunity Research Inst., Washington, DC (United States); Witherspoon, M.J. [National Association for State Community Service Programs, Washington, DC (United States); Brown, M.A. [Oak Ridge National Lab., TN (United States)

    1992-05-01

    This study is one of five parts of the US Department of Energy`s national evaluation of its Weatherization Assistance Program (WAP). It has three major goals: (1) to enumerate the size and sources of investment in low-income weatherization; (2) to provide a count of the number of low-income units weatherized by all weatherization programs and characterized the type and tenure of those homes; and (3) to document the extent to which the DOE/WAP funding has been expanded though use of external resources.

  8. The scope of the Weatherization Assistance Program: The weatherized population and the resource base

    Energy Technology Data Exchange (ETDEWEB)

    Power, M.; Eisenberg, J.F.; Michels, E. (Economic Opportunity Research Inst., Washington, DC (United States)); Witherspoon, M.J. (National Association for State Community Service Programs, Washington, DC (United States)); Brown, M.A. (Oak Ridge National Lab., TN (United States))

    1992-05-01

    This study is one of five parts of the US Department of Energy's national evaluation of its Weatherization Assistance Program (WAP). It has three major goals: (1) to enumerate the size and sources of investment in low-income weatherization; (2) to provide a count of the number of low-income units weatherized by all weatherization programs and characterized the type and tenure of those homes; and (3) to document the extent to which the DOE/WAP funding has been expanded though use of external resources.

  9. Stahlschüssel key to steel

    CERN Document Server

    Wegst, W S

    2016-01-01

    The Key to Steel (Stahlschlüssel/Stahlschluessel) cross reference book will help you to decode / decipher steel designations and find equivalent materials worldwide. The 2016 edition includes more than 70,000 standard designations and trade names from approximately 300 steelmakers and suppliers. Presentation is trilingual: English, French, and German. Materials covered include structural steels, tool steels, valve steels, high temperature steels and alloys, stainless and heat-resisting steels, and more. Standards and designations from 25 countries are cross-referenced.

  10. Effect of sanitizer combined with steam heating on the inactivation of foodborne pathogens in a biofilm on stainless steel.

    Science.gov (United States)

    Ban, Ga-Hee; Kang, Dong-Hyun

    2016-05-01

    The combined effect of chemical sanitizers including sodium hypochlorite, hydrogen peroxide, iodophor, and benzalkonium chloride with steam heating on the inactivation of biofilms formed by Escherichia coli O157:H7, Salmonella Typhimurium, and Listeria monocytogenes on stainless steel was investigated. Six day old biofilms, comprised of a mixture of three strains each of three foodborne pathogens, were produced on stainless steel coupons at 25 °C and treated with each sanitizer alone (for 5, 15, and 30 s), steam alone (for 5, 10, and 20 s), and the combination. There was a synergistic effect of sanitizer and steam on the viability of biofilm cells of the three pathogens as evidenced by plating counts and imaging. The combination treatment achieved an additional 0.01 to 2.78 log reduction compared to the sum of each individual treatment. The most effective combination for reducing levels of biofilm cells was the combination of steam and iodophor; steam for 20 s and merely 20 ppm iodophor for 30 s reduced cell numbers to below the detection limit (combination treatment of sanitizer with steam can be applied to control foodborne pathogens biofilm cells in food processing facilities as a potential intervention. Copyright © 2015 Elsevier Ltd. All rights reserved.

  11. Impact of the chemicals, essential for the purification process of strict Fe-hydrogenase, on the corrosion of mild steel.

    Science.gov (United States)

    Rouvre, Ingrid; Gauquelin, Charles; Meynial-Salles, Isabelle; Basseguy, Régine

    2016-06-01

    The influence of additional chemical molecules, necessary for the purification process of [Fe]-hydrogenase from Clostridium acetobutylicum, was studied on the anaerobic corrosion of mild steel. At the end of the purification process, the pure [Fe-Fe]-hydrogenase was recovered in a Tris-HCl medium containing three other chemicals at low concentration: DTT, dithionite and desthiobiotin. Firstly, mild steel coupons were exposed in parallel to a 0.1 M pH7 Tris-HCl medium with or without pure hydrogenase. The results showed that hydrogenase and the additional molecules were in competition, and the electrochemical response could not be attributed solely to hydrogenase. Then, solutions with additional chemicals of different compositions were studied electrochemically. DTT polluted the electrochemical signal by increasing the Eoc by 35 mV 24 h after the injection of 300 μL of control solutions with DTT, whereas it drastically decreased the corrosion rate by increasing the charge transfer resistance (Rct 10 times the initial value). Thus, DTT was shown to have a strong antagonistic effect on corrosion and was removed from the purification process. An optimal composition of the medium was selected (0.5 mM dithionite, 7.5 mM desthiobiotin) that simultaneously allowed a high activity of hydrogenase and a lower impact on the electrochemical response for corrosion tests.

  12. Determination of biocorrosion of low alloy steel by sulfate-reducing Desulfotomaculum sp. isolated from crude oil field

    Energy Technology Data Exchange (ETDEWEB)

    Cetin, D.; Doenmez, G. [Faculty of Science, Department of Biology, Ankara University, Tandogan, 06100, Ankara (Turkey); Bilgic, S. [Faculty of Science, Department of Chemistry, Ankara University, Tandogan, 06100, Ankara (Turkey); Doenmez, S. [Faculty of Engineering, Department of Food Engineering, Ankara University, Diskapi, 06110 Ankara (Turkey)

    2007-11-15

    In this study corrosion behavior of low alloy steel, in the presence of anaerobic sulfate-reducing Desulfotomaculum sp. which was isolated from an oil production well, was investigated. In order to determine corrosion rates and mechanisms, mass loss measurements and electrochemical polarization studies were performed without and with bacteria in the culture medium. Scanning electron microscopic observations and energy dispersive X-ray spectra (EDS) analysis were made on steel coupons. The effect of iron concentration on corrosion behavior was determined by Tafel extrapolation method. In a sterile culture medium, as the FeSO{sub 4} . 7H{sub 2}O concentration increased, corrosion potential (E{sub cor}) values shifted towards more anodic potentials and corrosion current density (I{sub cor}) values increased considerably. After inoculation of sulfate-reducing bacteria (SRB), E{sub cor} shifted towards cathodic values. I{sub cor} values increased with increasing incubation time for 10 and 100 mg/L concentrations of FeSO{sub 4} . 7H{sub 2}O. Results have shown that the corrosion activity changed due to several factors such as bacterial metabolites, ferrous sulfide, hydrogen sulfide, iron phosphide, and cathodic depolarization effect. (Abstract Copyright [2007], Wiley Periodicals, Inc.)

  13. Microbiological Corrosion in Low Carbon Steels

    Directory of Open Access Journals (Sweden)

    O. Medina–Custodio

    2009-01-01

    Full Text Available The Microbiologically Induced Corrosion affects several industries, such as oil industry where it is estimated that 20% to 30% pipes failures are related with microorganism . The chemical reactions generate ions transfer, this validate the use of electrochemical techniques for its analysis. Coupons submerged in a nutritional medium with presence and absence of three different microorganisms during two periods, 48 hours and 28 days we restudied. Polarization resistance (Rp and Electrochemical Impedance Spectroscopy (EIS techniques we re applied to determine the corrosivity of the systems. The results show a greater corrosive effect of abiotic system, this indicates a microorganisms protection effect to the metal, opposite to the first hypothesis. This result was ratified observing surfaces coupons by using Scanning Electron Microscopy (SEM technique. A possible mechanism based on Evans – Tafel graph is proposed to explain inhibitor microorganism effect.

  14. Cold-formed steel design

    CERN Document Server

    Yu, Wei-Wen

    2010-01-01

    The definitive text in the field, thoroughly updated and expanded Hailed by professionals around the world as the definitive text on the subject, Cold-Formed Steel Design is an indispensable resource for all who design for and work with cold-formed steel. No other book provides such exhaustive coverage of both the theory and practice of cold-formed steel construction. Updated and expanded to reflect all the important developments that have occurred in the field over the past decade, this Fourth Edition of the classic text provides you with more of the detailed, up-to-the-minute techni

  15. 2169 steel waveform experiments.

    Energy Technology Data Exchange (ETDEWEB)

    Furnish, Michael David; Alexander, C. Scott; Reinhart, William Dodd; Brown, Justin L.

    2012-11-01

    In support of LLNL efforts to develop multiscale models of a variety of materials, we have performed a set of eight gas gun impact experiments on 2169 steel (21% Cr, 6% Ni, 9% Mn, balance predominantly Fe). These experiments provided carefully controlled shock, reshock and release velocimetry data, with initial shock stresses ranging from 10 to 50 GPa (particle velocities from 0.25 to 1.05 km/s). Both windowed and free-surface measurements were included in this experiment set to increase the utility of the data set, as were samples ranging in thickness from 1 to 5 mm. Target physical phenomena included the elastic/plastic transition (Hugoniot elastic limit), the Hugoniot, any phase transition phenomena, and the release path (windowed and free-surface). The Hugoniot was found to be nearly linear, with no indications of the Fe phase transition. Releases were non-hysteretic, and relatively consistent between 3- and 5-mmthick samples (the 3 mm samples giving slightly lower wavespeeds on release). Reshock tests with explosively welded impactors produced clean results; those with glue bonds showed transient releases prior to the arrival of the reshock, reducing their usefulness for deriving strength information. The free-surface samples, which were steps on a single piece of steel, showed lower wavespeeds for thin (1 mm) samples than for thicker (2 or 4 mm) samples. A configuration used for the last three shots allows release information to be determined from these free surface samples. The sample strength appears to increase with stress from ~1 GPa to ~ 3 GPa over this range, consistent with other recent work but about 40% above the Steinberg model.

  16. 14 CFR 135.213 - Weather reports and forecasts.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 3 2010-01-01 2010-01-01 false Weather reports and forecasts. 135.213... Operating Limitations and Weather Requirements § 135.213 Weather reports and forecasts. (a) Whenever a person operating an aircraft under this part is required to use a weather report or forecast, that...

  17. 44 CFR 15.3 - Access to Mt. Weather.

    Science.gov (United States)

    2010-10-01

    ... 44 Emergency Management and Assistance 1 2010-10-01 2010-10-01 false Access to Mt. Weather. 15.3... HOMELAND SECURITY GENERAL CONDUCT AT THE MT. WEATHER EMERGENCY ASSISTANCE CENTER AND AT THE NATIONAL EMERGENCY TRAINING CENTER § 15.3 Access to Mt. Weather. Mt. Weather contains classified material and...

  18. 46 CFR 44.01-13 - Heavy weather plan.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 2 2010-10-01 2010-10-01 false Heavy weather plan. 44.01-13 Section 44.01-13 Shipping... VOYAGES Administration § 44.01-13 Heavy weather plan. (a) Each heavy weather plan under § 44.01-12(b) must... Inspection. Approval of a heavy weather plan is limited to the current hurricane season. (b) The...

  19. Highlights of Space Weather Services/Capabilities at NASA/GSFC Space Weather Center

    Science.gov (United States)

    Fok, Mei-Ching; Zheng, Yihua; Hesse, Michael; Kuznetsova, Maria; Pulkkinen, Antti; Taktakishvili, Aleksandre; Mays, Leila; Chulaki, Anna; Lee, Hyesook

    2012-01-01

    The importance of space weather has been recognized world-wide. Our society depends increasingly on technological infrastructure, including the power grid as well as satellites used for communication and navigation. Such technologies, however, are vulnerable to space weather effects caused by the Sun's variability. NASA GSFC's Space Weather Center (SWC) (http://science.gsfc.nasa.gov//674/swx services/swx services.html) has developed space weather products/capabilities/services that not only respond to NASA's needs but also address broader interests by leveraging the latest scientific research results and state-of-the-art models hosted at the Community Coordinated Modeling Center (CCMC: http://ccmc.gsfc.nasa.gov). By combining forefront space weather science and models, employing an innovative and configurable dissemination system (iSWA.gsfc.nasa.gov), taking advantage of scientific expertise both in-house and from the broader community as well as fostering and actively participating in multilateral collaborations both nationally and internationally, NASA/GSFC space weather Center, as a sibling organization to CCMC, is poised to address NASA's space weather needs (and needs of various partners) and to help enhancing space weather forecasting capabilities collaboratively. With a large number of state-of-the-art physics-based models running in real-time covering the whole space weather domain, it offers predictive capabilities and a comprehensive view of space weather events throughout the solar system. In this paper, we will provide some highlights of our service products/capabilities. In particular, we will take the 23 January and the 27 January space weather events as examples to illustrate how we can use the iSWA system to track them in the interplanetary space and forecast their impacts.

  20. Fabrication of stainless steel foil utilizing chromized steel strip

    Science.gov (United States)

    Loria, Edward A.

    1980-10-01

    Stainless steel foil has properties which are, in many respects, unmatched by alternative thin films. The high strength to weight ratio and resistance to corrosion and oxidation at elevated temperatures are generally advantageous. The aerospace and automotive industries have used Type 430 and 304 foil in turbine engine applications. Foil around 2 mils (5.1 × 10-3 cm) thick has been appropriate for the recuperator or heat exchanger and this product has also been used in honeycomb and truss-core structures. Further, such foil has been employed as a wrap to protect tool steel parts from contamination during heat treating. A large part of the high cost of producing stainless steel foil by rolling is due to the complicated and expensive rolling mill and annealing equipment involved. A method will be described which produces (solid) stainless steel foil from chromized (coated) steel which can be cheaper than the conventional processing stainless steel, such as Type 430, from ingot to foil. Also, the material is more ductile and less work hardenable during processing to foil and consequently intermediate annealing treatments are eliminated and scrap losses minimized.