WorldWideScience

Sample records for waste transfer line

  1. Shielding requirements for K Basin waste transfer line

    Energy Technology Data Exchange (ETDEWEB)

    Goldberg, H.J.

    1996-04-01

    K-East Basin sludge, mixed with water, is to be transported to the tank farms using a high integrity container mounted on a trailer. Load considerations preclude driving the truck directly to the tank opening. Thus, it is envisioned that a transfer line will run from a tanker unloading point to a point where the waste can be injected into a waste tank. It is presently envisioned that the waste will be pumped from the truck to the tank in a three inch pipe which is encased inside a six inch pipe. The transfer line will be shielded by either berming earth with a density of approximately 2.00 g/cm{sup 3} (125 lb/ft{sup 3}) around the line, or constructing a concrete raceway.

  2. EVALUATION OF FROST HEAVE ON WASTE TRANSFER LINES WITH SHALLOW DEPTHS IN DST (DOUBLE SHELL TANK) FARMS

    Energy Technology Data Exchange (ETDEWEB)

    HAQ MA

    2009-05-12

    The purpose of this document is to evaluate the effect of frost heave on waste transfer lines with shallow depths in DST farms. Because of the insulation, well compacted sandy material around waste transfer lines, the type of sandy and gravel soil, and relatively low precipitation at Hanford site, it is concluded that waste transfer lines with one foot of soil covers (sandy cushion material and insulation) are not expected to undergo frost heave damaging effects.

  3. Waste Transfer Stations

    DEFF Research Database (Denmark)

    Christensen, Thomas Højlund

    2011-01-01

    tion and transport is usually the most costly part of any waste management system; and when waste is transported over a considerable distance or for a long time, transferring the waste from the collection vehicles to more efficient transportation may be economically beneficial. This involves...... a transfer station where the transfer takes place. These stations may also be accessible by private people, offering flexibility to the waste system, including facilities for bulky waste, household hazardous waste and recyclables. Waste transfer may also take place on the collection route from small...... describes the main features of waste transfer stations, including some considerations about the economical aspects on when transfer is advisable....

  4. EVALUATION OF THE FAILURE OF A RADIOACTIVE WASTE TRANSFER LINE JACKET

    Energy Technology Data Exchange (ETDEWEB)

    Wiersma, B; Alan03 Plummer, A; Karthik Subramanian, K; Charles Jenkins, C; William Hinz, W; A Fellinger, A

    2007-04-06

    Radioactive wastes are confined in 49 underground storage tanks at the Savannah River Site. The waste is transported between tanks primarily via an underground transfer piping system. Due to the hazardous nature of the waste, the inner core stainless steel pipe is typically surrounded by a carbon steel pipe jacket, which provides secondary containment. Recently several through-wall penetrations were discovered on a segment of one of the jackets. An evaluation was performed to verify the failure mechanism and to estimate the degree of damage that occurred to the pipe segment. Failure analysis of a section of the jacket confirmed that pitting corrosion on the exterior of the pipe led to the through-wall penetration. Ultrasonic measurements on sections of the pipe were utilized to determine the remaining wall thickness in adjacent areas of the pipe. Based on these measurements, the degree of pitting and general corrosion was determined. Pit growth rate models were then developed to estimate the life expectancy of sections of the pipe that had not been excavated. The calculations estimated that the occurrence of through-wall failures in this jacket will begin to increase substantially in 12 years. Given that this pipe segment will be utilized beyond this time, short-term and long-term solutions to this failure were proposed. The short-term solutions focused on the repair or replace decisions that must be made to return the jacket to service as soon as practical. The long-term solutions focused on a broader strategy to address jacket integrity issues in the entire tank farm facility. These solutions included the evaluation of innovative remote inspection and repair techniques.

  5. Characterization of Vadose Zone Sediments from C Waste Management Area: Investigation of the C-152 Transfer Line Leak

    Energy Technology Data Exchange (ETDEWEB)

    Brown, Christopher F; Serne, R JEFFREY; Bjornstad, Bruce N; Valenta, Michelle M; Lanigan, David C; Vickerman, Tanya S; Clayton, Ray E; Geiszler, Keith N; Iovin, Cristian; Clayton, Eric T; Kutynakov, I V; Baum, Steven R; Lindberg, Michael J; Orr, Robert D

    2007-02-05

    A geologic/geochemical investigation in the vicinity of UPR-200-E-82 was performed using pairs of cone-penetrometer probe holes. A total of 41 direct-push cone-penetrometer borings (19 pairs to investigate different high moisture zones in the same sampling location and 3 individual) were advanced to characterize vadose zone moisture and the distribution of contaminants. A total of twenty sample sets, containing up to two split-spoon liners and one grab sample, were delivered to the laboratory for characterization and analysis. The samples were collected around the documented location of the C-152 pipeline leak, and created an approximately 120-ft diameter circle around the waste site. UPR-200-E-82 was a loss of approximately 2,600 gallons of Cs-137 Recovery Process feed solution containing an estimated 11,300 Ci of cesium-137 and 5 Ci of technetium-99. Several key parameters that are used to identify subsurface contamination were measured, including: water extract pH, electrical conductivity, nitrate, technetium-99, sodium, and uranium concentrations and technetium-99 and uranium concentrations in acid extracts. All of the parameters, with the exception of electrical conductivity, were elevated in at least some of the samples analyzed as part of this study. Specifically, soil pH was elevated (from 8.69 to 9.99) in five samples collected northeast and southwest of the C-152 pipeline leak. Similarly, samples collected from these same cone-pentrometer holes contained significantly more water-extractable sodium (more than 50 g/g of dry sediment), uranium (as much as 7.66E-01 g/g of dry sediment), nitrate (up to 30 g/g of dry sediment), and technetium-99 (up to 3.34 pCi/g of dry sediment). Most of the samples containing elevated concentrations of water-extractable sodium also had decreased levels of water extractable calcium and or magnesium, indicating that tank-related fluids that were high in sodium did seep into the vadose zone near these probe holes. Several of the

  6. Waste Feed Delivery Transfer System Analysis

    Energy Technology Data Exchange (ETDEWEB)

    JULYK, L.J.

    2000-05-05

    This document provides a documented basis for the required design pressure rating and pump pressure capacity of the Hanford Site waste-transfer system in support of the waste feed delivery to the privatization contractor for vitrification. The scope of the analysis includes the 200 East Area double-shell tank waste transfer pipeline system and the associated transfer system pumps for a11 Phase 1B and Phase 2 waste transfers from AN, AP, AW, AY, and A2 Tank Farms.

  7. Characterization of Vadose Zone Sediments from C Waste Management Area: Investigation of the C-152 Transfer Line Leak

    Energy Technology Data Exchange (ETDEWEB)

    Brown, Christopher F.; Serne, R. Jeffrey; Bjornstad, Bruce N.; Valenta, Michelle M.; Lanigan, David C.; Vickerman, Tanya S.; Clayton, Ray E.; Geiszler, Keith N.; Iovin, Cristian; Clayton, Eric T.; Kutnyakov, Igor V.; Baum, Steven R.; Lindberg, Michael J.; Orr, Robert D.

    2008-09-11

    The sodium data was removed due to potential contamination introduced during the acid extraction process. The rest of the text remains unchanged from the original report issued in January 2007. The overall goal of the Tank Farm Vadose Zone Project, led by CH2M HILL Hanford Group, Inc., is to define risks from past and future single-shell tank farm activities at Hanford. To meet this goal, CH2M HILL Hanford Group, Inc., tasked scientists from Pacific Northwest National Laboratory to perform detailed analyses on vadose zone sediments from within waste management area (WMA) C. Specifically, this report contains all the geologic, geochemical, and selected physiochemical characterization data compiled on vadose zone sediment recovered from direct-push samples collected around the site of an unplanned release (UPR), UPR-200-E-82, adjacent to the 241-C-152 Diversion Box located in WMA C.

  8. Helium transfer line installation details.

    CERN Multimedia

    G. Perinic

    2007-01-01

    A particularity of the 32 m long four in one helium transfer line in between the cold box in USC55 and the cavern UX5 is the fact that the transfer line passes through a hole in the crane rail support beam. In order to ensure the alignment of the suspension rail in the interconnecting tunnel with the hole in the rail support as well as the connection points at both ends required precise measurements of the given geometries as well as the installation of a temporary target for the verification of the theoretical predictions.

  9. Stability of the LHC transfer lines

    CERN Document Server

    Kain, V; Bartmann, W; Bracco, C; Goddard, B; Meddahi, M; Uythoven, J; Wenninger, J

    2011-01-01

    The LHC is filled from the SPS through two 3 km transfer lines. The injected beam parameters need to be well under control for luminosity performance, machine protection and operational efficiency. Small fractions of beam loss on the transfer line collimation system create showers which can trigger the sensitive LHC beam loss monitor system nearby and cause a beam abort during filling. The stability of the transfer line trajectory through the collimators is particularly critical in this respect. This paper will report on the transfer line trajectory stability during the proton run in 2011, correlations with injection losses, correction frequency and the most likely sources for the observed oscillations.

  10. <50> MeV transfer line

    CERN Multimedia

    CERN PhotoLab

    1972-01-01

    Measurement equipment around the 50 MeV transfer line from linac to booster. The vacuum pipe in the centre, with a temporary beam stopper in the foreground, leads to booster injection equipment. On the left is a spectrometer to determine energy spread, and in the right-hand line apparatus for emittance measurement.

  11. Transfer line tests take centre stage

    CERN Multimedia

    Katarina Anthony

    2014-01-01

    Last weekend, proton beams came knocking on the LHC's door. Shooting from the SPS and into the two LHC transfer lines, the proton beams were dumped just short of entering the accelerator.   The upper plot shows the trajectory of the first TI2 beam, which reached the end of the transfer line in a single attempt after 18 months of technical stop. Below, a smoother beam trajectory in TI2 after some corrections. For the first time since Run 1, the SPS to LHC transfer lines (TI8 and TI2) transported proton beams just short of the LHC. "We tested the beam instrumentation, the devices that measure the beam intensity, transverse beam profile, position and losses, as well as the beam collimators along the transfer lines," says Reyes Alemany Fernandez, the engineer in charge of the LHC. "We were also able to spot possible bottle necks in the beam trajectory and to perform the first optics measurements." Once the beams arrived at the transfer line beam dumps...

  12. 77 FR 69769 - Solid Waste Rail Transfer Facilities

    Science.gov (United States)

    2012-11-21

    ... Surface Transportation Board 49 CFR Part 1155 Solid Waste Rail Transfer Facilities AGENCY: Surface... solid waste rail transfer facilities. The Clean Railroads Act of 2008 amended the U.S. Code to restrict the jurisdiction of the Surface Transportation Board over solid waste rail transfer facilities. The...

  13. 76 FR 16538 - Solid Waste Rail Transfer Facilities

    Science.gov (United States)

    2011-03-24

    ... Surface Transportation Board 49 CFR Part 1155 Solid Waste Rail Transfer Facilities AGENCY: Surface...) over solid waste rail transfer facilities. The Clean Railroads Act also added three new statutory... the Board, a solid waste rail transfer facility need not comply with State laws, regulations, orders...

  14. Installation of the LHC transfer lines begins

    CERN Multimedia

    Patrice Loïez

    2003-01-01

    The first of 700 magnets has been installed in one of the two transfer tunnels built to transfer the SPS beam into the LHC. The start of this first installation phase of the LHC transfer lines provides the opportunity to launch a new and highly original modular system for transporting and installing all kinds of magnets in very narrow tunnels. The system is based on very compact bogies, up to four of which can be coupled together to form a convoy. The wheels are fitted with individual motors enabling them to swivel through an angle of 90° and the convoy to move laterally. The first installation phase will continue until mid-April. In addition to the magnets, a beam dump facility also has to be installed. The second installation phase will take place later this year and should be completed in 2004, when the TI 8 transfer line is due to be tested. The second transfer line, in tunnel TI 2, should be ready in April 2007, once the LHC magnets have been transported through the downstream section of this tunnel.Pho...

  15. Installation of the LHC transfer lines begins

    CERN Multimedia

    Patrice Loïez

    2003-01-01

    The first of 700 magnets has been installed in one of the two transfer tunnels built to transfer the SPS beam into the LHC. The start of this first installation phase of the LHC transfer lines provides the opportunity to launch a new and highly original modular system for transporting and installing all kinds of magnets in very narrow tunnels. The system is based on very compact bogies, up to four of which can be coupled together to form a convoy. The wheels are fitted with individual motors enabling them to swivel through an angle of 90° and the convoy to move laterally. In this way the magnet is delivered directly to its installation point, but beneath the beamline. It is then raised into its final position in the beamline using air cushions, which form an integrated part of the transport system.Photo 01: Pictured with the newly installed magnet and transport system in the transfer line tunnel are (left to right) Volker Mertens, responsible for the LHC injection and transfer lines; personnel involved in tr...

  16. Installation of the LHC transfer lines begins

    CERN Multimedia

    Patrice Loïez

    2003-01-01

    The first of 700 magnets has been installed in one of the two transfer tunnels built to transfer the SPS beam into the LHC. The start of this first installation phase of the LHC transfer lines provides the opportunity to launch a new and highly original modular system for transporting and installing all kinds of magnets in very narrow tunnels. The system is based on very compact bogies, up to four of which can be coupled together to form a convoy. The wheels are fitted with individual motors enabling them to swivel through an angle of 90° and the convoy to move laterally. The first installation phase will continue until mid-April. In addition to the magnets, a beam dump facility also has to be installed. The second installation phase will take place later this year and should be completed in 2004, when the TI 8 transfer line is due to be tested. The second transfer line, in tunnel TI 2, should be ready in April 2007, once the LHC magnets have been transported through the downstream section of this tunnel. We...

  17. Installation of the LHC transfer lines begins

    CERN Multimedia

    Patrice Loïez

    2003-01-01

    The first of 700 magnets has been installed in one of the two transfer tunnels built to transfer the SPS beam into the LHC. The start of this first installation phase of the LHC transfer lines provides the opportunity to launch a new and highly original modular system for transporting and installing all kinds of magnets in very narrow tunnels. The system is based on very compact bogies, up to four of which can be coupled together to form a convoy. The wheels are fitted with individual motors enabling them to swivel through an angle of 90° and the convoy to move laterally. The first installation phase will continue until mid-April. In addition to the magnets, a beam dump facility also has to be installed. The second installation phase will take place later this year and should be completed in 2004, when the TI 8 transfer line is due to be tested. The second transfer line, in tunnel TI 2, should be ready in April 2007, once the LHC magnets have been transported through the downstream section of this tunnel. Th...

  18. Installation of the LHC transfer lines begins

    CERN Multimedia

    2003-01-01

    On 19 February, the very first magnet was installed in one of the two tunnels that will house the transfer lines leading to the LHC. This magnet, recycled from a previous facility, was transported and positioned using a novel system designed for conveying large objects through narrow tunnels.

  19. LHC administrators with transfer line magnets

    CERN Document Server

    Laurent Guiraud

    2001-01-01

    Left to right: Lyn Evans (LHC project leader), Luciano Maiani (CERN’s Director-General at the time), Alexander Skrinsky, Kurt Hubner, on the last of 360 dipole magnets and 180 quadrupoles from Novosibirsk in Russia. They will form the transfer lines carrying protons into the LHC from the Super Proton Synchrotron (SPS).

  20. Estimating waste transfer station delays using GPS.

    Science.gov (United States)

    Wilson, Bruce Gordon; Vincent, Julie K

    2008-01-01

    This paper examines the use of on-board global positioning system (GPS) data recorders as a method to collect field data on the movements of solid waste collection vehicles at transfer stations. The movements of five waste collection vehicles using four different transfer facilities were compared over a period of 1 year. The spatial data were analyzed using geofences to determine the amount of time each truck spent on each of four activities: queuing for access to the weigh scale, sitting on the weigh scale, queuing for access to the tipping floor, and unloading waste. The study found that queuing delays can be identified and measured using GPS data. The average time at a facility for all trucks was 16.4 min per visit, with a standard deviation of 14.3 min. Time at the facility ranged between 2 and 111 min per visit and the distribution of time at the facility was positively skewed. Multi-compartment vehicles (co-collection and recycling trucks) spent significantly more time at unloading facilities. There were also significant differences in the length and the location of the queues at different facilities. At one facility, the longest delays were encountered while waiting for the weigh scale, at two facilities trucks experienced delays in obtaining access to the tipping floor, while at the fourth facility no significant delays developed.

  1. Installation of the LHC transfer lines begins

    CERN Multimedia

    Patrice Loïez

    2003-01-01

    The first of 700 magnets has been installed in one of the two transfer tunnels built to transfer the SPS beam into the LHC. The start of this first installation phase of the LHC transfer lines provides the opportunity to launch a new and highly original modular system for transporting and installing all kinds of magnets in very narrow tunnels. The system is based on very compact bogies, up to four of which can be coupled together to form a convoy. The wheels are fitted with individual motors enabling them to swivel through an angle of 90° and the convoy to move laterally. In this way the magnet is delivered directly to its installation point, but beneath the beamline. It is then raised into its final position in the beamline using air cushions, which form an integrated part of the transport system. Here we see the transport vehicle alongside the magnet supports. Visible in the background is the first magnet in place.

  2. Installation of the LHC transfer lines begins

    CERN Multimedia

    Patrice Loïez

    2003-01-01

    The first of 700 magnets has been installed in one of the two transfer tunnels built to transfer the SPS beam into the LHC. The start of this first installation phase of the LHC transfer lines provides the opportunity to launch a new and highly original modular system for transporting and installing all kinds of magnets in very narrow tunnels. The system is based on very compact bogies, up to four of which can be coupled together to form a convoy. The wheels are fitted with individual motors enabling them to swivel through an angle of 90° and the convoy to move laterally. In this way the magnet is delivered directly to its installation point, but beneath the beamline. It is then raised into its final position in the beamline using air cushions, which form an integrated part of the transport system.Photos 01, 02: Pictured with the newly installed magnet and transport system in the transfer line tunnel are LHC project leader Lyn Evans (second left, white helmet); Volker Mertens, responsible for the LHC injecti...

  3. Particulate Matter Oxidative Potential from Waste Transfer Station Activity

    National Research Council Canada - National Science Library

    Krystal J. Godri; Sean T. Duggan; Gary W. Fuller; Tim Baker; David Green; Frank J. Kelly; Ian S. Mudway

    ...). The highest PM concentrations in London occur in proximity to waste transfer stations (WTS), sites that experience high numbers of dust-laden, heavy-duty diesel vehicles transporting industrial and household waste. Objective...

  4. PIP-II Transfer Line Design

    Energy Technology Data Exchange (ETDEWEB)

    Vivoli, A. [Fermilab

    2016-10-15

    The U.S. Particle Physics Project Prioritization Panel (P5) report encouraged the realization of Fermilab's Proton Improvement Plan II (PIP-II) to support future neutrino programs in the United States. PIP-II aims at enhancing the capabilities of the Fermilab existing accelerator complex while simultaneously providing a flexible platform for its future upgrades. The central part of PIP-II project is the construction of a new 800 MeV H- Superconducting (SC) Linac together with upgrades of the Booster and Main Injector synchrotrons. New transfer lines will also be needed to deliver beam to the down-stream accelerators and facilities. In this paper we present the recent development of the design of the transfer lines discussing the principles that guided their design, the constraints and requirements imposed by the existing accelerator complex and the following modifications implemented to comply with a better understanding of the limitations and further requirements that emerged during the development of the project.

  5. Tank Waste Transport, Pipeline Plugging, and the Prospects for Reducing the Risk of Waste Transfers

    Energy Technology Data Exchange (ETDEWEB)

    Welch, T.D.

    2001-09-27

    This report provides an overview of the capabilities and limitations of some current models being applied to the analysis of waste transfers; identifies the modeling capabilities needed to reduce the risk of pipeline plugging during tank waste transfers; and summarizes ongoing, planned, and future work needed to add these capabilities. Development of improved waste transport modeling tools with these capabilities will also help with waste transfer planning and evaluation, process control, and diagnosis of plugging events. Other potential applications include evaluation of waste-mixing scenarios, analysis of waste transfer stability, analysis of waste-unplugging alternatives, minimization of water addition, maximization of system availability, evaluation of risk-reduction strategies, and evaluation of cost-reduction strategies.

  6. Transfer line TT70 (electrons from PS to SPS)

    CERN Multimedia

    CERN PhotoLab

    1981-01-01

    As injectors for LEP, PS and SPS had to be converted to the acceleration of electrons and positrons. So far, only positively charged particles had been transferred from the PS to the SPS, for the negatively charged electrons a new transfer line, TT70, had to be built. Due to the difference in level of the two machines, the transfer line slopes and tilts.

  7. Technology transfer in hazardous waste management

    Energy Technology Data Exchange (ETDEWEB)

    Drucker, H.

    1989-01-01

    Hazardous waste is a growing problem in all parts of the world. Industrialized countries have had to deal with the treatment and disposal of hazardous wastes for many years. The newly industrializing countries of the world are now faced with immediate problems of waste handling. The developing nations of the world are looking at increasing quantities of hazardous waste generation as they move toward higher levels of industrialization. Available data are included on hazardous waste generation in Asia and the Pacific as a function of Gross Domestic Product (GDP). Although there are many inconsistencies in the data (inconsistent hazardous waste definitions, inconsistent reporting of wastes, etc.) there is definite indication that a growing economy tends to lead toward larger quantities of hazardous waste generation. In developing countries the industrial sector is growing at a faster rate than in the industrialized countries. In 1965 industry accounted for 29% of GDP in the developing countries of the world. In 1987 this had grown to 37% of GDP. In contrast, industry accounted for 40% of GDP in 1965 in industrialized countries and dropped to 35% in 1987. This growth in industrial activity in the developing countries brings an increase in the need to handle hazardous wastes. Although hazardous wastes are ubiquitous, the control of hazardous wastes varies. The number of regulatory options used by various countries in Asia and the Pacific to control wastes are included. It is evident that the industrialized countries, with a longer history of having to deal with hazardous wastes, have found the need to use more mechanisms to control them. 2 refs., 2 figs.

  8. Comparative analysis on flexibility requirements of typical Cryogenic Transfer lines

    Science.gov (United States)

    Jadon, Mohit; Kumar, Uday; Choukekar, Ketan; Shah, Nitin; Sarkar, Biswanath

    2017-04-01

    The cryogenic systems and their applications; primarily in large Fusion devices, utilize multiple cryogen transfer lines of various sizes and complexities to transfer cryogenic fluids from plant to the various user/ applications. These transfer lines are composed of various critical sections i.e. tee section, elbows, flexible components etc. The mechanical sustainability (under failure circumstances) of these transfer lines are primary requirement for safe operation of the system and applications. The transfer lines need to be designed for multiple design constraints conditions like line layout, support locations and space restrictions. The transfer lines are subjected to single load and multiple load combinations, such as operational loads, seismic loads, leak in insulation vacuum loads etc. [1]. The analytical calculations and flexibility analysis using professional software are performed for the typical transfer lines without any flexible component, the results were analysed for functional and mechanical load conditions. The failure modes were identified along the critical sections. The same transfer line was then refurbished with the flexible components and analysed for failure modes. The flexible components provide additional flexibility to the transfer line system and make it safe. The results obtained from the analytical calculations were compared with those obtained from the flexibility analysis software calculations. The optimization of the flexible component’s size and selection was performed and components were selected to meet the design requirements as per code.

  9. A STRUCTURAL INTEGRITY EVALUATION OF THE TANK FARM WASTE TRANSFER SYSTEM

    Energy Technology Data Exchange (ETDEWEB)

    Wiersma, B.

    2006-03-09

    Radioactive supernate, salt, and/or sludge wastes (i.e., high level wastes) are confined in 49 underground storage tanks at the Savannah River Site (SRS). The waste is transported between tanks within and between the F and H area tank farms and other facilities on site via underground and a limited number of aboveground transfer lines. The Department of Energy - Savannah River Operations Office (DOE-SR) performed a comprehensive assessment of the structural integrity program for the Tank Farm waste transfer system at the SRS. This document addresses the following issues raised during the DOE assessment: (1) Inspections of failed or replaced transfer lines indicated that the wall thickness of some core and jacket piping is less than nominal; (2) No corrosion allowance is utilized in the transfer line structural qualification calculations. No basis for neglecting corrosion was provided in the calculations; (3) Wall loss due to erosion is not addressed in the transfer line structural qualification calculations; and (4) No basis is provided for neglecting intergranular stress corrosion cracking in the transfer line structural qualification calculations. The common theme in most of these issues is the need to assess the potential for occurrence of material degradation of the transfer line piping. The approach used to resolve these issues involved: (1) Review the design and specifications utilized to construct and fabricate the piping system; (2) Review degradation mechanisms for stainless steel and carbon steel and determine their relevance to the transfer line piping; (3) Review the transfer piping inspection data; (4) Life estimation calculations for the transfer lines; and (5) A Fitness-For-Service evaluation for one of the transfer line jackets. The evaluation concluded that the transfer line system piping has performed well for over fifty years. Although there have been instances of failures of the stainless steel core pipe during off-normal service, no significant

  10. Evaluation of Hose in Hose Transfer Line Service Life for Hanford's Interim Stabilization Program

    Energy Technology Data Exchange (ETDEWEB)

    TORRES, T.D.

    2000-08-24

    RPP-6153, Engineering Task Plan for Hose-in-Hose Transfer System for the Interim Stabilization Program, defines the programmatic goals, functional requirements, and technical criteria for the development and subsequent installation of transfer line equipment to support Hanford's Interim Stabilization Program. RPP-6028, Specification for Hose in Hose Transfer Lines for Hanford's Interim Stabilization Program, has been issued to define the specific requirements for the design, manufacture, and verification of transfer line assemblies for specific waste transfer applications. Included in RPP-6028 are tables defining the chemical constituents of concern to which transfer lines will be exposed. Current Interim Stabilization Program planning forecasts that the at-grade transfer lines will be required to convey pumpable waste for as much as three years after commissioning. Prudent engineering dictates that the equipment placed in service have a working life in excess of this forecasted time period, with some margin to allow for future adjustments to the planned schedule. This document evaluates the effective service life of the Hose-in-Hose Transfer Lines, based on information submitted by the manufacturer and published literature. The effective service life of transfer line assemblies is a function of several factors. Foremost among these are process fluid characteristics, ambient environmental conditions, and the manufacturer's stated shelf life. This evaluation examines the manufacturer's certification of shelf life, the manufacturer's certifications of chemical compatibility with waste, and published literature on the effects of exposure to ionizing radiation on the mechanical properties of elastomeric materials to evaluate transfer line service life.

  11. Hazard evaluation for transfer of waste from tank 241-SY-101 to tank 241-SY-102

    Energy Technology Data Exchange (ETDEWEB)

    SHULTZ, M.V.

    1999-04-05

    Tank 241-SY-101 waste level growth is an emergent, high priority issue. The purpose of this document is to record the hazards evaluation process and document potential hazardous conditions that could lead to the release of radiological and toxicological material from the proposed transfer of a limited quantity (approximately 100,000 gallons) of waste from Tank 241-SY-101 to Tank 241-SY-102. The results of the hazards evaluation were compared to the current Tank Waste Remediation System (TWRS) Basis for Interim Operation (HNF-SD-WM-BIO-001, 1998, Revision 1) to identify any hazardous conditions where Authorization Basis (AB) controls may not be sufficient or may not exist. Comparison to LA-UR-92-3196, A Safety Assessment for Proposed Pump Mixing Operations to Mitigate Episodic Gas Releases in Tank 241-SY-101, was also made in the case of transfer pump removal activities. Revision 1 of this document deletes hazardous conditions no longer applicable to the current waste transfer design and incorporates hazardous conditions related to the use of an above ground pump pit and overground transfer line. This document is not part of the AB and is not a vehicle for requesting authorization of the activity; it is only intended to provide information about the hazardous conditions associated with this activity. The AB Control Decision process will be used to determine the adequacy of controls and whether the proposed activity is within the AB. This hazard evaluation does not constitute an accident analysis.

  12. Lean manufacturing implementation in reducing waste for electronic assembly line

    Directory of Open Access Journals (Sweden)

    Zakaria Nurul Husna

    2017-01-01

    Full Text Available Lean manufacturing is the most convenient way to eliminate unnecessary waste and can provide what customers demand. This paper presents possibilities and sustainability of application of lean manufacturing method by using a virtual simulation of the workers performance in a line production of small and medium industry. Actual case study and Witness simulation were used in this study to find the waste that exists in the production and identified the performance of workers in the production line. Lean manufacturing concept has identified and rectified problems related to low productivity in the assembly line. The case study is involved a line production for electronic part assembly. The result of this preliminary study should illustrate the relationship of worker’s performance by lean manufacturing method as well as the productivity improvements which help to reduce cost for manufacturer. Lean manufacturing method has been used during the study to reduce the cost when waste is eliminated by reducing the workstation without reducing the performance of the production. The performance of the production is increased when allocating the labor in a needed working area. Lastly, the study also proves that the new layout has improved the process to be used for future production process.

  13. Design of the LINAC4 Transfer Line Quadrupole Electromagnets

    CERN Document Server

    Vanherpe, L

    2013-01-01

    Beam focusing in the various segments of the Linac4 Transfer Line is provided by quadrupole electromagnets. In total seventeen pulsed, air-cooled quadrupole electromagnets are required. They are made of laminated electrical steel yokes and coils wound from solid copper wire. All magnets have an aperture radius of 50 mm and are required to provide an integrated field gradient of 1.8 T over a magnetic length of 300 mm. This design report summarizes the main magnetic, electrical and mechanical design parameters of the Linac4 Transfer Line Quadrupole Magnets. The effect of the vacuum chamber on the magnetic field quality and the field delay is studied.

  14. Geometry and Optics of the Electrostatic ELENA Transfer Lines

    CERN Document Server

    Vanbavinckhove, G; Barna, D; Bartmann, W; Butin, F; Choisnet, O; Yamada, H

    2013-01-01

    The future ELENA ring at CERN will decelerate the AD anti-proton beam further from 5.3 MeV to 100 keV kinetic energy, to increase the efficiency of anti-proton trapping. At present there are four experiments in the AD hall which will be complemented with the installation of ELENA by additional three experiments and an additional source for commissioning. This paper describes the optimization of the transfer line geometry, ring rotation and source position. The optics of the transfer lines and error studies to define field and alignment tolerances are shown, and the optics particularities of electrostatic elements and their optimization highlighted.

  15. Modeling of Heat Transfer in LDConverter (BOF) Lining

    OpenAIRE

    Jahan, Georgina

    2012-01-01

    During the production of steel in the LD converter the refractory lining is exposed to high temperature emulsion of steel, slag and gas. It protects the steel body of the vessel to come in contact with the molten steel.The main purpose of this work was to observe the temperature distribution profile in converter refractory lining which is very important to understand the life of the refractory lining of the LD converter.In this study, a three dimensional (3D) heat transfer model for the refra...

  16. Update of the Linac4-PSB Transfer Line

    CERN Document Server

    HEIN, Lutz

    2010-01-01

    The installation of Linac4 represents the first step of the upgrade plans of the CERN accelerator complex for the future in order to raise the available proton flux to attain amongst others the LHC ultimate luminosity. This linac is capable to accelerate H--ions from 45keV to 160MeV, which will be injected into the Proton Synchrotron Booster (PSB). The increase of energy from 50MeV (Linac2) to 160MeV (Linac4) allows to overcome the space charge limitations at the PSB injection, which is the main bottleneck towards higher beam brightness in the downstream accelerator chain. In order to preserve beam quality from the outlet of Linac4 to PSB injection the design of the transfer line becomes crucial. As the location of Linac4 was chosen in view of upgrade scenarios, the construction of a new transfer line is foreseen, see ref.[1] and ref.[2]. Here part of the Linac2-PSB transfer line will be re-used. In the new part of the transfer line the beam is horizontally and vertically adjusted towards the bending magnet B...

  17. Injection and transfer lines of the PS Booster

    CERN Multimedia

    Photographic Service

    1972-01-01

    In the foreground is the vacuum chamber for the 50 MeV proton beam coming from the Linac. The tank held by white frames houses the "Vertical Distributor", which deflects the Linac beam to the levels of the Booster's 4 superposed rings. After acceleration in the Booster, originally to 800 MeV, today to 1.4 GeV, the beams from the 4 rings are combined in the vertical plane and transfered to the 26 GeV PS. The "Recombination Line", intersecting the injection line, crosses the picture from left to right.

  18. Mass transfers through electromagnetically stirred interfaces - nuclear wastes application

    Energy Technology Data Exchange (ETDEWEB)

    Courtessole, C.; Etay, J. [CNRS-SIMAP-EPM ENSEEG BP75 38402 St Martin d' Heres Cedex (France); SAADI, B.; Allibert, M. [23 Av. Marcellin Berthelot 38100 Grenoble (France)

    2009-06-15

    Molten salts are good heat conductors. They are identified for future applications such as the implementation of a GEN IV nuclear reactor, heat transportation between 650 deg. and 850 deg. C for the hydrogen generation purpose, and electrolysis of aluminum between 850 deg. and 950 deg. C. Generally speaking, these salts are aggressive for materials that maintain them such as transportation, mixing and chemical composition. That is why we want to study and implement induction devices to replace the functions of these materials by electromagnetic forces. This will allow a dual benefit: improving the longevity and reduce secondary wastes. In the present work, we use a specific electromagnetic device for accelerating mass transfers through liquid / liquid interface. To reduce barriers to transfer, the interface is shacked at a frequency near of one of its natural frequencies. To achieve this, we use an adapted dual-frequency electromagnetic field. A pyrometallurgy pre-industrial graded facility, based on cold crucible technique, is used to carry out numerous experiments on the extraction of actinides and other elements from a fluorinated salt into a liquid metal phase containing a reducing agent such as magnesium, aluminium or lithium. At time t = 0, the metallic alloy is poured under the molten salt. Metallic samples are taken from the bulk at known time intervals. Later, the samples are analysed using optical ICP. Transfer rate and kinetics are deduced from obtained experimental data. Compare to other treatment, the present one is found to lead faster to a higher rate of transfer. (authors)

  19. New magnet transport system for the LHC beam transfer lines

    CERN Multimedia

    Patrice Loïez

    2003-01-01

    The first of 700 magnets has been installed in one of the two transfer tunnels built to transfer the SPS beam into the LHC. The start of this first installation phase of the LHC transfer lines provides the opportunity to launch a new and highly original modular system for transporting and installing all kinds of magnets in very narrow tunnels. The system (pictured here in one of the tunnels) is based on very compact bogies, up to four of which can be coupled together to form a convoy. The wheels are fitted with individual motors enabling them to swivel through an angle of 90° and the convoy to move laterally. The lead vehicle is powered by an electric rail set into the roof of the tunnel. The system is backed up by electrical batteries that enable it to operate in the absence of an outside power source or in the event of power failure. Last but not least, for the long-distance transport of magnets, it can be optically guided by a line traced on the tunnel floor. The convoy moves through the particularly narr...

  20. The Bending Magnets for the Proton Transfer Line of CNGS

    CERN Document Server

    Schirm, K M; Anashin, V; Kiselev, O; Maraev, V; Ogurtsov, A; Pupkov, Yu; Ruvinsky, E; Zhilyaev, K; Konstantinov, Yu S; Kosjakin, M; Peregud, V

    2006-01-01

    The project "CERN neutrinos to Gran Sasso (CNGS)", a collaboration between CERN and the INFN (Gran Sasso Laboratory) in Italy, will study neutrino oscillations in a long base-line experiment. High-energy protons will be extracted from the CERN SPS accelerator, transported through a 727 m long transfer line and focused onto a graphite target to produce a beam of pions and kaons and subsequently neutrinos. The transfer line requires a total of 78 dipole magnets. They were produced in the framework of an in-kind contribution of Germany via DESY to the CNGS project. The normal conducting dipoles, built from laminated steel cores and copper coils, have a core length of 6.3 m, a 37 mm gap height and a nominal field range of 1.38 T - 1.91 T at a maximum current of 4950 A. The magnet design was a collaboration between CERN and BINP. The half-core production was subcontracted to EFREMOV Institute; the coil fabrication, magnet assembly and the field measurements were concluded at BINP in June 2004. The main design issu...

  1. Throughput centered prioritization of machines in transfer lines

    Energy Technology Data Exchange (ETDEWEB)

    Pascual, R., E-mail: rpascual@ing.puc.cl [Physical Asset Management Lab, Centro de Mineria, Pontificia Universidad Catolica de Chile, Av. Vicuna Mackenna 4860, Santiago (Chile); Godoy, D. [Physical Asset Management Lab, Centro de Mineria, Pontificia Universidad Catolica de Chile, Av. Vicuna Mackenna 4860, Santiago (Chile); Louit, D.M. [Komatsu Chile S.A., Av. Americo Vespucio 0631, Quilicura, Santiago (Chile)

    2011-10-15

    In an environment of scarce resources and complex production systems, prioritizing is key to confront the challenge of managing physical assets. In the literature, there exist a number of techniques to prioritize maintenance decisions that consider safety, technical and business perspectives. However, the effect of risk mitigating elements-such as intermediate buffers in production lines-on prioritization has not yet been investigated in depth. In this line, the work proposes a user-friendly graphical technique called the system efficiency influence diagram (SEID). Asset managers may use SEID to identify machines that have a greater impact on the system throughput, and thus set prioritized maintenance policies and/or redesign of buffers capacities. The tool provides insight to the analyst as it decomposes the influence of a given machine on the system throughput as a product of two elements: (1) system influence efficiency factor and (2) machine unavailability factor. We illustrate its applicability using three case studies: a four-machine transfer line, a vehicle assembly line, and an open-pit mining conveyor system. The results confirm that the machines with greater unavailability factors are not necessarily the most important for the efficiency of the production line, as it is the case when no intermediate buffers exist. As a decision aid tool, SEID emphasizes the need to move from a maintenance vision focused on machine availability, to a systems engineering perspective. - Highlights: > We propose a graphical technique to prioritize machines in production lines. > The tool is called 'system efficiency influence diagram' (SEID). > It helps setting prioritized maintenance policies and/or redesign of buffers. > The SEID technique focuses on system efficiency and throughput. > We illustrate its applicability using three case studies.

  2. The bending magnets for the LHC injection transfer lines

    CERN Document Server

    Anashin, V; Labutsky, S A; Mejidzade, V; Mikhailov, S; Pupkov, Yu A; Rouvinsky, E; Sukhina, B; Kalbreier, Willi; Kouba, G; Schirm, K M; Weisse, E; Konstantinov, Yu S; Kosjakin, M; Peregud, V

    2002-01-01

    Two injection transfer lines, each about 2.8 km long, with 51 and 107 degree horizontal deflection, are being built to transfer protons at 450 GeV from the Super Proton Synchrotron (SPS) to the Large Hadron Collider (LHC). A total of 360 dipole magnets are required; they have been produced in the framework of the contribution of the Russian Federation to the construction of the LHC. The classical dipoles, built from laminated steel cores and copper coils, have a core length of 6.3 m, 25 mm gap height and a nominal field of 1.81 T at a current of 5270 A. The magnet design was made in collaboration between CERN and BINP. An unusual design has been chosen for the coils to cope with the limited voltage from the available power supplies. All magnets in each of the two lines will be powered in series. The coil is composed of overlapping, but electrically insulated, half coils of 3 1/2 turns each. Thus, the power connections for IN and OUT are placed on opposite magnet ends. Short copper braids are used to connect a...

  3. Preliminary design of the CLIC drive-beam transfer line

    CERN Document Server

    D'Amico, T E

    1999-01-01

    In the drive-beam generation complex of CLIC there is an important beam transfer line between the drive-beam accelerator and the drive- beam decelerators, where the 30 GHz RF power is generated in the decelerator structures In the drive-beam generation complex of CLIC there is an important beam transfer line between the drive-beam accelerator and the drive-beam decelerators, where the 30 GHz RF power is generated in the decelerator structures. The design proposed for this transport system is based on building blocks or beam optics subsystems, which have been individually studied in detail and can be combined in order to cover specific functions. One function consists of bending the beams wherever required by the geometrical layout, so as to preserve the bunch length and keep the bending arc compact and compatible with acceptable synchrotron radiation. Other functions are to adjust the path length of each drive beam for synchronism with the main-linac beam and to compress or stretch the bunch according to the ...

  4. FASTWIND reloaded: Complete comoving frame transfer for ``all'' contributing lines

    Science.gov (United States)

    Puls, Joachim

    2017-11-01

    FASTWIND is a unified NLTE atmosphere/spectrum synthesis code originally designed (and frequently used) for the optical/IR spectroscopic analysis of massive stars with winds. Until the previous version (v10), the line transfer for background elements (mostly from the iron-group) was performed in an approximate way, by calculating the individual line-transitions in a single-line Sobolev or comoving frame approach, and by adding up the individual opacities and source functions to quasi-continuum quantities that are used to determine the radiation field for the complete spectrum (see Puls et al. 2005, A&A 435, 669, and updates). We have now updated this approach (v11) and calculate, for all contributing lines (from elements H to Zn), the radiative transfer in the comoving frame, thus also accounting for line-overlap effects in an ``exact'' way. Related quantities such as temperature, radiative acceleration and formal integral have been improved in parallel. For a typical massive star atmospheric model, the computation times (from scratch, and for a modern desktop computer) are 1.5 h for the atmosphere/NLTE part, and 30 to 45 minutes (when not parallelized) for the formal integral (i.e., SED and normalized flux) in the ranges 900 to 2000 and 3800 to 7000 Å(Δλ = 0.03 Å). We compare our new with analogous results from the alternative code CMFGEN (Hillier & Miller 1998, ApJ 496, 407, and updates), for a grid consisting of 5 O-dwarf and 5 O-supergiant models of different spectral subtype. In most cases, the agreement is very good or even excellent (i.e., for the radiative acceleration), though also certain differences can be spotted. A comparison with results from the previous, approximate method shows equally good agreement, though also here some differences become obvious. Besides the possibility to calculate the (total) radiative acceleration, the new FASTWIND version will allow us to investigate the UV-part of the spectrum in parallel with the optical/IR domain.

  5. BPM SYSTEM FOR THE SNS RING AND TRANSFER LINES.

    Energy Technology Data Exchange (ETDEWEB)

    DAWSON,W.C.; CAMERON,P.; CERNIGLIA,P.; CUPOLO,J.; DEGEN,C.; DELLAPENNA,A.; HUHN,A.; KESSELMAN,M.; MEAD,J.; SIKORA,R.

    2002-05-06

    The Spallation Neutron Source Ring accumulates about 1060 pulses of 38mA peak current IGeV H-minus particles from the Linac thru the HEBT line, then delivers this accumulated beam in a single pulse to the mercury target via the RTBT line. Bunching frequency of beam in the HEBT line is 402.5MHz, and about 1MHz in the Ring and RTBT. Position monitor electrodes in HEBT are of the shorted stripline type, with apertures of 12cm except in the dispersive bend, where the aperture is 21cm. Ring and RTBT electrodes are open striplines, with apertures of 21, 26, 30, and 36cm. All pickups are dual plane. The electronics will be PC-based with the Analog/Digital Front End passing data and receiving control and timing thru a custom PC1 interface developed by LANL[l]. LabVIEW will be used to direct the acquisition, process the data, and transfer results via Ethernet to the EPICS control system. To handle the dynamic range required with well over 60dB variation in signal size, the Ring and RTBT electronics will employ a fast gain switching technique that will take advantage of the 300ns tail-to-head gap to provide position measurement during the entire accumulation cycle. Beam-based alignment will be utilized as part of the system calibration.

  6. On-Line Learning Modules For Waste Treatment, Waste Disposal and Waste Recycling

    Science.gov (United States)

    O'Callaghan, Paul; Soos, Lubomir; Brokes, Peter

    2011-12-01

    This contribution is devoted to the development of an advanced vocational education and training system for professionals working in (or intending to enter) the waste management industry realized through the Leonardo project WASTRE. The consortium of the Project WASTRE includes 3 well known Technical Universities in Central Europe (TU Vienna, CVUT Prague and STU Bratislava). The project implements new didactical tools from projects EDUET, ELEVATE, RESNET and MENUET developed by MultiMedia SunShine, headed by Prof. Paul Callaghan for this education and training system. This system will be tested within courses organized by at least 3 institutions of vocational education and training: the Technical and vocational secondary school Tlmace, CHEWCON Humenne and the Union of Chambers of Craftsmen and Tradesmen of ESKISEHIR. The faculty of Mechanical Engineering (FME) of STU will coordinate the project WASTRE and will participate in the preparation of e-learning materials, organization of the courses and in the design of syllabuses, curricula, assessment and evaluation methods for the courses, the testing of developed learning materials, evaluating experiences from a pilot course and developing the e-learning materials according to the needs of end-users.

  7. Safety evaluation for packaging (onsite) concrete-lined waste packaging

    Energy Technology Data Exchange (ETDEWEB)

    Romano, T.

    1997-09-25

    The Pacific Northwest National Laboratory developed a package to ship Type A, non-transuranic, fissile excepted quantities of liquid or solid radioactive material and radioactive mixed waste to the Central Waste Complex for storage on the Hanford Site.

  8. Transfer line from the PSB to the PS (recombination)

    CERN Multimedia

    CERN PhotoLab

    1976-01-01

    After sequential ejection of 5 bunches from each of the 4 rings of the Booster (originally 800 MeV, now 1.4 GeV), the 4 batches are brought to the same vertical level, so as to form a string of 20 bunches, filling the circumference of the PS. This vertical "recombination" is performed in the transfer line, using vertical bending magnets, septa and kickers. Here we see the section where the beam from ring 4 (the top one) is brought down to the level of ring 3, and the beam from ring 1 up to the level of ring 2. Further downstream (to the right, outside this picture), level 2 is brought up to level 3, identical to that of the PS. After this original recombination scheme, other ways of combining the 4 beams, vertically and/or longitudinally, were developed and used in operation.

  9. QTG quadrupole magnets for the CNGS transfer line

    CERN Document Server

    Cornuet, D; Levichev, E B; Pavlov, O; Pupkov, Yu A; Ruvinsky, E; Zickler, T

    2004-01-01

    The QTG quadrupole magnets will be a part of the CERN Neutrino to Gran Sasso (CNGS) transfer line. 23 QTG magnets will be used as lattice and matching quadrupoles. They are being produced in the framework of a German in-kind contribution via DESY to CNGS. The QTG magnets have a maximum gradient of 40 T/m at the 530 A excitation current and are manufactured from laminated steel cores. The yoke length is 2.2 m and the inscribed radius is 22.5 mm. The excitation coils are made of vacuum impregnated hollow copper conductor. The main design aspects and the results of the acceptance tests including mechanical, electrical and magnetic field measurements are described.

  10. Mitigated Transfer Line Leaks that Result in Surface Pools and Spray Leaks into Pits

    Energy Technology Data Exchange (ETDEWEB)

    HEY, B.E.

    1999-12-07

    This analysis provides radiological and toxicological consequence calculations for postulated mitigated leaks during transfers of six waste compositions. Leaks in Cleanout Boxes equipped with supplemental covers and leaks in pits are analyzed.

  11. Changes to the Transfer Line Collimation System for the High-Luminosity LHC Beams

    CERN Document Server

    Kain, V; Bracco, C; Fraser, M; Galleazzi, F; Gianfelice-Wendt, E; Kosmicki, A; Maciariello, F; Meddahi, M; Nuiry, F X; Steele, G; Velotti, F

    2015-01-01

    The current LHC transfer line collimation system will not be able to provide enough protection for the high brightness beams in the high-luminosity LHC era. The new collimation system will have to attenuate more and be more robust than its predecessor. The active jaw length of the new transfer line collimators will therefore be 2.1 m instead of currently 1.2 m. The transfer line optics will have to be adjusted for the new collimator locations and larger beta functions at the collimators for absorber robustness reasons. In this paper the new design of the transfer line collimation system will be presented with its implications on transfer line optics and powering, maintainability, protection of transfer line magnets in case of beam loss on a collimator and protection of the LHC aperture.

  12. Changes to the Transfer Line Collimation System for the High-Luminosity LHC Beams

    Energy Technology Data Exchange (ETDEWEB)

    Kain, V. [CERN; Aberle, O. [CERN; Bracco, C. [CERN; Fraser, M. [CERN; Galleazzi, F. [CERN; Gianfelice-Wendt, E. [Fermilab; Kosmicki, A. [CERN; Maciariello, F. [CERN; Meddahi, M. [CERN; Nuiry, F. X. [CERN; Steele, G. [CERN; Velotti, F. [CERN

    2015-06-01

    The current LHC transfer line collimation system will not be able to provide enough protection for the high brightness beams in the high-luminosity LHC era. The new collimation system will have to attenuate more and be more robust than its predecessor. The active jaw length of the new transfer line collimators will therefore be 2.1 m instead of currently 1.2 m. The transfer line optics will have to be adjusted for the new collimator locations and larger beta functions at the collimators for absorber robustness reasons. In this paper the new design of the transfer line collimation system will be presented with its implications on transfer line optics and powering, maintainability, protection of transfer line magnets in case of beam loss on a collimator and protection of the LHC aperture.

  13. Modeling transient heat transfer in nuclear waste repositories.

    Science.gov (United States)

    Yang, Shaw-Yang; Yeh, Hund-Der

    2009-09-30

    The heat of high-level nuclear waste may be generated and released from a canister at final disposal sites. The waste heat may affect the engineering properties of waste canisters, buffers, and backfill material in the emplacement tunnel and the host rock. This study addresses the problem of the heat generated from the waste canister and analyzes the heat distribution between the buffer and the host rock, which is considered as a radial two-layer heat flux problem. A conceptual model is first constructed for the heat conduction in a nuclear waste repository and then mathematical equations are formulated for modeling heat flow distribution at repository sites. The Laplace transforms are employed to develop a solution for the temperature distributions in the buffer and the host rock in the Laplace domain, which is numerically inverted to the time-domain solution using the modified Crump method. The transient temperature distributions for both the single- and multi-borehole cases are simulated in the hypothetical geological repositories of nuclear waste. The results show that the temperature distributions in the thermal field are significantly affected by the decay heat of the waste canister, the thermal properties of the buffer and the host rock, the disposal spacing, and the thickness of the host rock at a nuclear waste repository.

  14. Collection, transfer and transport of waste: accounting of greenhouse gases and global warming contribution

    DEFF Research Database (Denmark)

    Eisted, Rasmus; Larsen, Anna Warberg; Christensen, Thomas Højlund

    2009-01-01

    The collection, transfer and transport of waste are basic activities of waste management systems all over the world. These activities all use energy and fuels, primarily of fossil origin. Electricity and fuel consumptions of the individual processes were reviewed and greenhouse gases (GHG......) emissions were quantified. The emission factors were assigned a global warming potential (GWP) and aggregated into global warming factors (GWFs), which express the potential contribution to global warming from collection, transport and transfer of 1 tonne of wet waste. Six examples involving collection...

  15. W-314, waste transfer alternative piping system description

    Energy Technology Data Exchange (ETDEWEB)

    Papp, I.G.

    1998-04-30

    It is proposed that the reliability, operability, and flexibility of the Retrieval Transfer System be substantially upgraded by replacing the planned single in-farm pipeline from the AN-AY-AZ-(SY) Tank Farm Complex to the AP Farm with three parallel pipelines outside the tank farms. The proposed system provides simplified and redundant routes for the various transfer missions, and prevents the risk of transfer gridlock when the privatization effort swings into full operation.

  16. Conceptual modeling to optimize the haul and transfer of municipal solid waste.

    Science.gov (United States)

    Komilis, D P

    2008-11-01

    Two conceptual mixed integer linear optimization models were developed to optimize the haul and transfer of municipal solid waste (MSW) prior to landfilling. One model is based on minimizing time (h/d), whilst the second model is based on minimizing total cost (euro/d). Both models aim to calculate the optimum pathway to haul MSW from source nodes (waste production nodes, such as urban centers or municipalities) to sink nodes (landfills) via intermediate nodes (waste transfer stations). The models are applicable provided that the locations of the source, intermediate and sink nodes are fixed. The basic input data are distances among nodes, average vehicle speeds, haul cost coefficients (in euro/ton km), equipment and facilities' operating and investment cost, labor cost and tipping fees. The time based optimization model is easier to develop, since it is based on readily available data (distances among nodes). It can be used in cases in which no transfer stations are included in the system. The cost optimization model is more reliable compared to the time model provided that accurate cost data are available. The cost optimization model can be a useful tool to optimally allocate waste transfer stations in a region and can aid a community to investigate the threshold distance to a landfill above which the construction of a transfer station becomes financially beneficial. A sensitivity analysis reveals that queue times at the landfill or at the waste transfer station are key input variables. In addition, the waste transfer station ownership and the initial cost data affect the optimum path. A case study at the Municipality of Athens is used to illustrate the presented models.

  17. Determination of Erosion/Corrosion Rates in Hanford Tank Farms Radioactive Waste Transfer System Pipelines

    Energy Technology Data Exchange (ETDEWEB)

    Washenfelder, D. J.; Girardot, C. L.; Wilson, E. R.; Page, J. A.; Engeman, J. K.; Gunter, J. R.; Johnson, J. M.; Baide, D. G.; Cooke, G. A.; Larson, J. D.; Castleberry, J. L.; Boomer, K. D.

    2015-11-05

    The twenty-eight double-shell underground radioactive waste storage tanks at the U. S. Department of Energy’s Hanford Site near Richland, WA are interconnected by the Waste Transfer System network of buried steel encased pipelines and pipe jumpers in below-grade pits. The pipeline material is stainless steel or carbon steel in 51 mm to 152 mm (2 in. to 6 in.) sizes. The pipelines carry slurries ranging up to 20 volume percent solids and supernatants with less than one volume percent solids at velocities necessary to prevent settling. The pipelines, installed between 1976 and 2011, were originally intended to last until the 2028 completion of the double-shell tank storage mission. The mission has been subsequently extended. In 2010 the Tank Operating Contractor began a systematic evaluation of the Waste Transfer System pipeline conditions applying guidelines from API 579-1/ASME FFS-1 (2007), Fitness-For-Service. Between 2010 and 2014 Fitness-for-Service examinations of the Waste Transfer System pipeline materials, sizes, and components were completed. In parallel, waste throughput histories were prepared allowing side-by-side pipeline wall thinning rate comparisons between carbon and stainless steel, slurries and supernatants and throughput volumes. The work showed that for transfer volumes up to 6.1E+05 m3 (161 million gallons), the highest throughput of any pipeline segment examined, there has been no detectable wall thinning in either stainless or carbon steel pipeline material regardless of waste fluid characteristics or throughput. The paper describes the field and laboratory evaluation methods used for the Fitness-for-Service examinations, the results of the examinations, and the data reduction methodologies used to support Hanford Waste Transfer System pipeline wall thinning conclusions.

  18. Timetable Optimization of Rail Transit Loop Line with Transfer Coordination

    National Research Council Canada - National Science Library

    Shi, Rui-Jia; Mao, Bao-Hua; Ding, Yong; Bai, Yun; Chen, Yao

    2016-01-01

    .... This is performed by adjusting the headways and dwell times of trains on the loop line. A genetic algorithm is applied to solve the proposed model, and a numerical example is used to verify its effectiveness...

  19. Collection, transfer and transport of waste: accounting of greenhouse gases and global warming contribution.

    Science.gov (United States)

    Eisted, Rasmus; Larsen, Anna W; Christensen, Thomas H

    2009-11-01

    The collection, transfer and transport of waste are basic activities of waste management systems all over the world. These activities all use energy and fuels, primarily of fossil origin. Electricity and fuel consumptions of the individual processes were reviewed and greenhouse gases (GHG) emissions were quantified. The emission factors were assigned a global warming potential (GWP) and aggregated into global warming factors (GWFs), which express the potential contribution to global warming from collection, transport and transfer of 1 tonne of wet waste. Six examples involving collection, transfer and transport of waste were assessed in terms of GHG emissions, including both provision and use of energy. (GHG emissions related to production, maintenance and disposal of vehicles, equipment, infrastructure and buildings were excluded.) The estimated GWFs varied from 9.4 to 368 kg CO(2)-equivalent (kg CO(2)-eq.) per tonne of waste, depending on method of collection, capacity and choice of transport equipment, and travel distances. The GHG emissions can be reduced primarily by avoiding transport of waste in private cars and by optimization of long distance transport, for example, considering transport by rail and waterways.

  20. Numerical Modeling of Thermofluid Transients During Chilldown of Cryogenic Transfer Lines

    Science.gov (United States)

    Majumdar, Alok; Steadman, Todd

    2003-01-01

    The chilldown of fluid transfer lines is an important part of using cryogenic systems such as those found in both ground and space based applications. The chilldown process is a complex combination of both thermal and fluid transient phenomena. A cryogenic liquid flows through a transfer line that is initially at a much higher temperature than the cryogen. Transient heat transfer processes between the liquid and transfer line cause vaporization of the liquid, and this phase change can cause transient pressure and flow surges in the liquid. As the transfer line is cooled, these effects diminish until the liquid reaches a steady flow condition in the chilled transfer line. If these transient phenomena are not properly accounted for in the design process of a cryogenic system, it can lead to damage or failure of system components during operation. For such cases, analytical modeling is desirable for ensuring that a cryogenic system transfer line design is adequate for handling the effects of a chilldown process. The purpose of this paper is to present the results of a numerical model developed using Generalized Fluid System Simulation Program (GFSSP)'s new fluid transient capability in combination with its previously developed thermal transient capability to predict pressure and flow surge in cryogenic transfer lines during a chilldown process. An experiment performed by the National Bureau of Standards (NBS) in 1966 has been chosen as the baseline comparison case for this work. NBS s experimental set-up consisted of a 10.59 cu ft supply dewar, an inlet valve, and a 200 ft long, - in Outside Diameter (OD) vacuum jacketed copper transfer line that exhausted to atmosphere. Three different inlet valves, a - in port ball valve, a 1 in port globe valve and a 1 in port gate valve, were used in NBS s experiments. Experiments were performed using both liquid hydrogen and liquid nitrogen as the fluids. The proposed paper will include detailed comparisons of GFSSP s predictions

  1. [Method for estimating the population risk attributable to a transfer station of municipal solid waste].

    Science.gov (United States)

    Santos-Burgoa, C; Rojas-Bracho, L; Barrera-Romero, N; Ongay-Delhumeau, E; Escamilla-Cejudo, J A

    1992-01-01

    Due to the great volume of municipal solid waste that is produced daily in the Metropolitan Area of Mexico City a sound management has been an impossible task. This is why during the past few years solid waste transfer stations have been constructed in the City, allowing a more efficient solid waste collection. The attributable risk to the population's health for the operation of such stations needs to be assessed in order to have them working within the urbanized areas without posing a potential risk to the health of the inhabitants of the inhabitants of the surrounding areas.

  2. Towards Neutron Drip Line via Transfer-Type Reactions

    CERN Document Server

    Penionzhkevich, Yu E; Antonenko, N V

    2005-01-01

    Possibilities of production of light neutron-rich isotopes $^{24,26}$O, $^{32}$Ne, $^{36,38}$Mg, $^{42}$Si and $^{56,58,60}$Ca in transfer-type reactions are analyzed. The optimal conditions for their production are suggested. The measurement of the excitation function can allow us to estimate the binding energy of exotic nuclei.

  3. Knowledge and technology transfer to improve the municipal solid waste management system of Durango City, Mexico.

    Science.gov (United States)

    Valencia-Vázquez, Roberto; Pérez-López, Maria E; Vicencio-de-la-Rosa, María G; Martínez-Prado, María A; Rubio-Hernández, Rubén

    2014-09-01

    As society evolves its welfare level increases, and as a consequence the amount of municipal solid waste increases, imposing great challenges to municipal authorities. In developed countries, municipalities have established integrated management schemes to handle, treat, and dispose of municipal solid waste in an economical and environmentally sound manner. Municipalities of developing and transition countries are not exempted from the challenges involving municipal solid waste handling, but their task is not easy to accomplish since they face budget deficits, lack of knowledge, and deficiencies in infrastructure and equipment. In the northern territory of Mexico, the municipality of Durango is facing the challenge of increased volumes of waste with a lack of adequate facilities and infrastructure. This article analyses the evolution of the municipal solid waste management of Durango city, which includes actions such as proper facilities construction, equipment acquisition, and the implementation of social programmes. The World Bank, offering courses to municipal managers on landfill operation and waste management, promoted the process of knowledge and technology transfer. Thereafter, municipal authorities attended regional and some international workshops on waste management. In addition they followed suggestions of international contractors and equipment dealers with the intention to improve the situation of the waste management of the city. After a 15-year period, transfer of knowledge and technology resulted in a modern municipal solid waste management system in Durango municipality. The actual system did not reach the standard levels of an integrated waste management system, nevertheless, a functional evaluation shows clear indications that municipality actions have put them on the right pathway. © The Author(s) 2014.

  4. Analysis of Radiation Levels Associated with Operation of the RHIC Transfer Line

    Energy Technology Data Exchange (ETDEWEB)

    Stevens, A. J. [Brookhaven National Lab. (BNL), Upton, NY (United States)

    1994-12-13

    This note is intended to document calculations of prompt radiation dose in regions exterior to the berm which now exists over the Transfer Line between the AGS and the Relativistic Heavy Ion Collider.

  5. UC-Berkeley-area citizens decry waste transfer from lab.

    CERN Multimedia

    Nakasato, L

    2002-01-01

    Residents are working to stop the transfer of potentially hazardous and radioactive material from Lawrence Berkeley National Laboratory. The lab has begun to dismantle the Bevatron which has been shut down since 1993 and says eight trucks per day will move material offsite (1 page).

  6. Local heat transfer in an in-line tube bundle with asymmetrical flow

    DEFF Research Database (Denmark)

    Meyer, Knud Erik

    1999-01-01

    Measurements of the local heat transfer in themiddle of a small in-line tube bundle with longitudinal to transverse pitches of $1.5\\times 1.8$ are performed at a Reynolds number of $30\\,000$. Asymmetrical distributions of the local heat transfer are found. The distributions are in good agreement...... with earlier flow measurements. The mean heat transfer rate is only little affected bythe asymmetrical conditions....

  7. Application of industrial robots in automatic disassembly line of waste LCD displays

    Science.gov (United States)

    Wang, Sujuan

    2017-11-01

    In the automatic disassembly line of waste LCD displays, LCD displays are disassembled into plastic shells, metal shields, circuit boards, and LCD panels. Two industrial robots are used to cut metal shields and remove circuit boards in this automatic disassembly line. The functions of these two industrial robots, and the solutions to the critical issues of model selection, the interfaces with PLCs and the workflows were described in detail in this paper.

  8. Slope and Line of Best Fit: A Transfer of Knowledge Case Study

    Science.gov (United States)

    Nagle, Courtney; Casey, Stephanie; Moore-Russo, Deborah

    2017-01-01

    This paper brings together research on slope from mathematics education and research on line of best fit from statistics education by considering what knowledge of slope students transfer to a novel task involving determining the placement of an informal line of best fit. This study focuses on two students who transitioned from placing inaccurate…

  9. York Region integrated solid waste processing and transfer facility : cash flow analysis of alternatives

    Energy Technology Data Exchange (ETDEWEB)

    Balfour, B. [Gartner Lee Ltd., Markham, ON (Canada)

    2000-07-01

    Cash flow modeling exercises of the two tier waste management system in York Region was presented to encourage decision-makers to think in terms of total system costs and how to achieve a desired diversion rate. The York Region consists of 9 municipalities which collect their own waste. The region is responsible for its treatment and disposal. This paper have shown that modeling of realistic options gives decision-makers the opportunity to see the financial impact of different types of waste management systems and provides them with the potential to view the critical parameters in the cost of waste management. This paper demonstrated through modelling the impacts of various alternatives such as collection, processing, transfer and disposal, and identified achievable diversions.

  10. An Algorithm to Compress Line-transition Data for Radiative-transfer Calculations

    Science.gov (United States)

    Cubillos, Patricio E.

    2017-11-01

    Molecular line-transition lists are an essential ingredient for radiative-transfer calculations. With recent databases now surpassing the billion-line mark, handling them has become computationally prohibitive, due to both the required processing power and memory. Here I present a temperature-dependent algorithm to separate strong from weak line transitions, reformatting the large majority of the weaker lines into a cross-section data file, and retaining the detailed line-by-line information of the fewer strong lines. For any given molecule over the 0.3-30 μm range, this algorithm reduces the number of lines to a few million, enabling faster radiative-transfer computations without a significant loss of information. The final compression rate depends on how densely populated the spectrum is. I validate this algorithm by comparing Exomol’s HCN extinction-coefficient spectra between the complete (65 million line transitions) and compressed (7.7 million) line lists. Over the 0.6-33 μm range, the average difference between extinction-coefficient values is less than 1%. A Python/C implementation of this algorithm is open-source and available at https://github.com/pcubillos/repack. So far, this code handles the Exomol and HITRAN line-transition format.

  11. The On-line Waste Library (OWL): Usage and Inventory Status Report

    Energy Technology Data Exchange (ETDEWEB)

    Sassani, David [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Jang, Je-Hun [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Mariner, Paul [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Price, Laura L. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Rechard, Robert P. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Rigali, Mark J. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Rogers, Ralph [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Stein, Emily [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Walkow, Walter M. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Weck, Philippe F. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2016-09-23

    The Waste Form Disposal Options Evaluation Report (SNL 2014) evaluated disposal of both Commercial Spent Nuclear Fuel (CSNF) and DOE-managed HLW and Spent Nuclear Fuel (DHLW and DSNF) in the variety of disposal concepts being evaluated within the Used Fuel Disposition Campaign. That work covered a comprehensive inventory and a wide range of disposal concepts. The primary goal of this work is to evaluate the information needs for analyzing disposal solely of a subset of those wastes in a Defense Repository (DRep; i.e., those wastes that are either defense related, or managed by DOE but are not commercial in origin). A potential DRep also appears to be safe in the range of geologic mined repository concepts, but may have different concepts and features because of the very different inventory of waste that would be included. The focus of this status report is to cover the progress made in FY16 toward: (1) developing a preliminary DRep included inventory for engineering/design analyses; (2) assessing the major differences of this included inventory relative to that in other analyzed repository systems and the potential impacts to disposal concepts; (3) designing and developing an on-line waste library (OWL) to manage the information of all those wastes and their waste forms (including CSNF if needed); and (4) constraining post-closure waste form degradation performance for safety assessments of a DRep. In addition, some continuing work is reported on identifying potential candidate waste types/forms to be added to the full list from SNL (2014 – see Table C-1) which also may be added to the OWL in the future. The status for each of these aspects is reported herein.

  12. GARLIC - A general purpose atmospheric radiative transfer line-by-line infrared-microwave code: Implementation and evaluation

    Science.gov (United States)

    Schreier, Franz; Gimeno García, Sebastián; Hedelt, Pascal; Hess, Michael; Mendrok, Jana; Vasquez, Mayte; Xu, Jian

    2014-04-01

    A suite of programs for high resolution infrared-microwave atmospheric radiative transfer modeling has been developed with emphasis on efficient and reliable numerical algorithms and a modular approach appropriate for simulation and/or retrieval in a variety of applications. The Generic Atmospheric Radiation Line-by-line Infrared Code - GARLIC - is suitable for arbitrary observation geometry, instrumental field-of-view, and line shape. The core of GARLIC's subroutines constitutes the basis of forward models used to implement inversion codes to retrieve atmospheric state parameters from limb and nadir sounding instruments. This paper briefly introduces the physical and mathematical basics of GARLIC and its descendants and continues with an in-depth presentation of various implementation aspects: An optimized Voigt function algorithm combined with a two-grid approach is used to accelerate the line-by-line modeling of molecular cross sections; various quadrature methods are implemented to evaluate the Schwarzschild and Beer integrals; and Jacobians, i.e. derivatives with respect to the unknowns of the atmospheric inverse problem, are implemented by means of automatic differentiation. For an assessment of GARLIC's performance, a comparison of the quadrature methods for solution of the path integral is provided. Verification and validation are demonstrated using intercomparisons with other line-by-line codes and comparisons of synthetic spectra with spectra observed on Earth and from Venus.

  13. Simulation and experimental research of heat leakage of cryogenic transfer lines

    Science.gov (United States)

    Deng, B. C.; Xie, X. J.; Pan, W.; Jiang, R. X.; Li, J.; Yang, S. Q.; Li, Q.

    2017-12-01

    The heat leakage of cryogenic transfer lines directly influences the performance of large-scale helium refrigerator. In this paper, a thermal model of cryogenic transfer line considering numerical simulation of support coupled with MLI was established. To validate the model, test platform of cryogenic transfer lines with the merits of disassembly outer pipe and changeable easily multi-layer insulation has been built. The experimental results of heat leakage through overall length of cryogenic transfer lines, support and multi-layer insulation were obtained. The heat leakages of multi-layer insulation, a support and the overall leakage are 1.02 W/m, 0.44 W and 1.46 W/m from experimental data, respectively. The difference of heat leakage of MLI between experiment and simulation were less than 5%. The temperature distribution of support and MLI obtained in presented model in good agreement with experimental data. It is expected to reduce the overall heat leakage of cryogenic transfer lines further by optimizing structure of support based on the above thermal model and test platform in this paper.

  14. Portable reconfigurable line sensor (PRLS) and technology transfer

    Energy Technology Data Exchange (ETDEWEB)

    MacKenzie, D.P. [Air Force Electronic Systems Center, Hanscom AFB, MA (United States); Buckle, T.H. [Sandia National Labs., Albuquerque, NM (United States); Blattman, D.A. [Racon, Inc., Seattle, WA (United States)

    1993-12-31

    The Portable Reconfigurable Line Sensor (PRLS) is a bistatic, pulsed-Doppler, microwave intrusion detection system developed at Sandia National Laboratories for the US Air Force. The PRLS is rapidly and easily deployed, and can detect intruders ranging from a slow creeping intruder to a high speed vehicle. The system has a sharply defined detection zone and will not falsely alarm on nearby traffic. Unlike most microwave sensors, the PRLS requires no alignment or calibration. Its portability, battery operation, ease of setup, and RF alarm reporting capability make it an excellent choice for perimeter, portal, and gap-filler applications in the important new field of rapidly-deployable sensor systems. In October 1992, the US Air Force and Racon, Inc., entered into a Cooperative Research and Development Agreement (CRADA) to commercialize the PRLS, jointly sharing government and industry resources. The Air Force brings the user`s perspective and requirements to the cooperative effort. Sandia, serving as the technical arm of the Air Force, adds the actual PRLS technology to the joint effort, and provides security systems and radar development expertise. Racon puts the Air Force requirements and Sandia technology together into a commercial product, making the system meet important commercial manufacturing constraints. The result is a true ``win-win`` situation, with reduced government investment during the commercial development of the PRLS, and industry access to technology not otherwise available.

  15. The role played by environmental factors in the integration of a transfer station in a municipal solid waste management system.

    Science.gov (United States)

    Bovea, M D; Powell, J C; Gallardo, A; Capuz-Rizo, S F

    2007-01-01

    Transfer stations are an integral part of present-day municipal solid waste management systems. The main criteria used to decide on the location of a transfer station has traditionally been the minimization of transport costs, since it is cheaper to transport great amounts of waste over long distances in large loads than in small ones. In this study, we are going to consider the environmental factor in order to compare the feasibility of using a transfer station integrated within a waste management system. Applying the Life Cycle Assessment technique will enable us to obtain an objective parameter that quantifies the environmental impact of transportation and of operating a transfer station. Taking the current rates of solid wastes generation in the Plana region of Castellón (Spain) as our starting point, in this study we compare the environmental costs involved in the process of taking municipal wastes directly to the nearest waste treatment facility, with those involved in a waste management system integrating a transfer station. Comparing these two cases, an average reduction of 16.8% in the environmental impact can be obtained when a transfer station is incorporated in the waste management system.

  16. OPERATIONAL CHALLENGES IN MIXING AND TRANSFER OF HIGH YIELD STRESS SLUDGE WASTE

    Energy Technology Data Exchange (ETDEWEB)

    Caldwell, T.; Bhatt, P.

    2009-12-07

    The ability to mobilize and transport non-Newtonian waste is essential to advance the closure of highly radioactive storage tanks. Recent waste removal operations from Tank 12H at the Savannah River Site (SRS) encountered sludge mixtures with a yield stress too high to pump. The waste removal equipment for Tank 12H was designed to mobilize and transport a diluted slurry mixture through an underground 550m long (1800 ft) 0.075m diameter (3 inch) pipeline. The transfer pump was positioned in a well casing submerged in the sludge slurry. The design allowed for mobilized sludge to enter the pump suction while keeping out larger tank debris. Data from a similar tank with known rheological properties were used to size the equipment. However, after installation and startup, field data from Tank 12H confirmed the yield stress of the slurry to exceed 40 Pa, whereas the system is designed for 10 Pa. A revision to the removal strategy was required, which involved metered dilution, blending, and mixing to ensure effective and safe transfer performance. The strategy resulted in the removal of over 255,000 kgs of insoluble solids with four discrete transfer evolutions for a total transfer volume of 2400 m{sup 3} (634,000 gallons) of sludge slurry.

  17. Results of Waste Transfer and Back-Dilution in Tanks 241-SY-101 and 241-SY-102

    Energy Technology Data Exchange (ETDEWEB)

    LA Mahoney; ZI Antoniak; WB Barton; JM Conner; NW Kirch; CW Stewart; BE Wells

    2000-07-26

    This report chronicles the process of remediation of the flammable gas hazard in Tank 241-SY-101 (SY-101) by waste transfer and back-dilution from December 18, 1999 through April 2, 2000. A brief history is given of the development of the flammable gas retention and release hazard in this tank, and the transfer and dilution systems are outlined. A detailed narrative of each of the three transfer and dilution campaigns is given to provide structure for the balance of the report. Details of the behavior of specific data are then described, including the effect of transfer and dilution on the waste levels in Tanks SY-101 and SY-102, data from strain gauges on equipment suspended from the tank dome, changes in waste configuration as inferred from neutron and gamma logs, headspace gas concentrations, waste temperatures, and the mixerpump operating performance. Operating data and performance of the transfer pump in SY-101 are also discussed.

  18. The new transfer line collimation system for the LHC high luminosity era

    CERN Document Server

    Kain, V; Goddard, B; Maciariello, F; Meddahi, M; Mereghetti, A; Steele, G; Velotti, F; Gianfelice-Wendt, E

    2014-01-01

    A set of passive absorbers is located at the end of each of the 3 km long injection lines to protect the LHC in case of failures during the extraction process from the LHC’s last pre-injector or in the beam transfer itself. In case of an erroneous extraction, the absorbers have to attenuate the beam to a safe level and be robust enough themselves to survive the impact. These requirements are difficult to fulfill with the very bright and intense beams produced by the LHC injectors for the high luminosity era. This paper revisits the requirements for the LHC transfer line collimation system and the adapted strategy to fulfill these for the LHC high luminosity era. A possible solution for the new transfer line collimation system is presented.

  19. The New Transfer Line Collimation System for the LHC High Luminosity Era

    Energy Technology Data Exchange (ETDEWEB)

    Kain, Verena [CERN; Bracco, Chiara [CERN; Goddard, Brennan [CERN; Maciariello, Fausto [CERN; Meddahi, Malika [CERN; Mereghetti, Alessio [CERN; Steele, Genevieve [CERN; Velotti, Francesco [CERN; Gianfelice-Wendt, Eliana [Fermilab

    2014-07-01

    A set of passive absorbers is located at the end of each of the 3 km long injection lines to protect the LHC in case of failures during the extraction process from the LHC’s last pre-injector or the beam transfer itself. In case of an erroneous extraction, the absorbers have to attenuate the beam to a safe level and be robust enough themselves to survive the impact. These requirements are difficult to fulfil with the very bright and intense beams produced by the LHC injectors for the high luminosity era. This paper revisits the requirements for the SPS-to-LHC transfer line collimation system and the adapted strategy to fulfill these for the LHC high luminosity operation. A possible solution for the new transfer line collimation system is presented.

  20. A STRUCTURAL INTEGRITY ASSESSMENT OF UNDERGROUND PIPING ASSOCIATED WITH THE TRANSFER OF RADIOACTIVE WASTE

    Energy Technology Data Exchange (ETDEWEB)

    Wiersma, B

    2006-04-25

    Radioactive wastes are confined in 49 underground storage tanks at the Savannah River Site. The waste is transported between tanks via underground transfer piping. An assessment of the structural integrity of the transfer piping was performed to ensure that the present condition of the piping was sound and to provide life expectancy estimates for the piping based on anticipated service. The assessment reviewed the original design of the piping, the potential and observed degradation mechanisms, the results from past inspections of the piping, and a Fitness-For-Service evaluation for a section of piping that experienced pitting in a locally thinned area. The assessment concluded that the piping was structurally sound. Assuming that service conditions remain the same, the piping will remain functional for its intended service life.

  1. Line of Sight: A process for transferring science from the laboratory to the market place

    Energy Technology Data Exchange (ETDEWEB)

    LINTON,JONATHAN; WALSH,STEVEN; LOMBANA,CESAR A.; HUNTER,WILLARD B.; ROMIG JR.,ALTON D.

    2000-02-14

    Commercialization and transfer of technology from laboratories in academia, government, and industry has only met a fraction of its potential and is currently an art not a science. The line of sight approach developed and in use at Sandia National Laboratories, is used to better understand commercialization and transfer of technology. The line of sight process integrates technology description, the dual process model of innovation and the product introduction model. The model, that the line of sight is based OR is presented and the application of the model to both disruptive and sustaining technologies is illustrated. Work to date suggests that the differences between disruptive and sustaining technologies are critical to quantifying the level of risk and choosing the commercialization path. The applicability of the line of sight to both disruptive and sustaining technologies is key to the success of the model and approach.

  2. Project W-314 Specific Test and Evaluation Plan for 200E Waste Transfer System

    Energy Technology Data Exchange (ETDEWEB)

    HAMMERS, J.S.

    2000-02-25

    The purpose of this Specific Test and Evaluation Plan (STEP) is to provide a detailed written plan for the systematic testing of the newly constructed 200E Waste Transfer System in the W-314 Project. The STEP provides the outline for test and evaluation methods that verify the system's performance and compliance to the established Project design criteria. The STEP is a ''lower tier'' document based on the W-314 Test & Evaluation Plan (TEP).

  3. Measuring externalities of waste transfer stations in Israel using hedonic pricing.

    Science.gov (United States)

    Eshet, Tzipi; Baron, Mira G; Shechter, Mordechai; Ayalon, Ofira

    2007-01-01

    This study estimates the economic value of externalities related to waste transfer stations in Israel. Most externalities are associated with local disamenities experienced by residents living in close proximity to transfer stations - including noise, odor, litter, vermin, visual intrusion and any associated perceived discomfort. Following the mapping of all active transfer stations in Israel, problematic sites near residential areas were identified. Four of these sites were selected for detailed examination. The study involved estimating the economic value of disamenities using the Hedonic Price Method, which examines the impact of disamenities on property values. The results indicate that the maximum spatial extent of the impact occurs about 2.8km away from a transfer station with an increase of about $5000 in housing price for each additionalkm away from the site. Alternatively, an increase of 1% in the average distance of a house from the local transfer station is associated with a 0.06% rise in the price of the average house. These figures, representing the relationship between changes in environmental quality and property prices, indicate that transfer stations create externalities that should be taken into account in location and clean-up policies for transfer stations as well as in potential compensation policies.

  4. Economic Analysis about the Solid Waste Quantities and Optimal Hauling Distance to Install Transfer Stations in Colombia

    National Research Council Canada - National Science Library

    Perdomo, Jorge; Ramírez, Juan

    2011-01-01

    The main objective of this study is to develop an economic analysis estimating the solid waste quantities and optimal hauling distance to install transfer stations in Colombia, according to landfill location...

  5. Effect of mass transfer on concentration wave propagation during anaerobic digestion of solid waste.

    Science.gov (United States)

    Vavilin, Vasily A; Shchelkanov, Micael Yu; Rytov, Sergey V

    2002-05-01

    A distributed model of anaerobic digestion of solid waste was developed to study effects of mass transfer on the rate of propagation of initiation methanogenic area. The diffusion and advection of volatile fatty acids (VFA) and methanogenic biomass were taken into account in the model of a one-dimensional (ID) reactor. It was considered that VFA inhibits both polymer hydrolysis and acetoclastic methanogenesis. This approach allows to view the bioreactor as an active medium that provokes concentration waves from some area of methanogenic initiation (local VFA depression) to the total reactor volume. The model shows that mass transfer-based acceleration of methane production in the reactor is possible when the intensity of VFA utilization in the methanogenic area is sufficient for a complete digestion of the incoming VFA. Otherwise, initiation methanogenic area will be suppressed by increasing concentration of VFA. The obtained results emphasize the importance of considering spatial heterogeneity of the reaction for the analysis of solid anaerobic digestion in bioreactors and landfills. The digestion of solid waste can be optimized by setting the low rate of mass transfer (mixing or leachate recirculation) during lag-phase of the reaction with subsequent increase in the mass transfer rate in parallel with the propagation of methanogenic population. In this case, the rate of concentration waves substantially increases.

  6. On-line calorific value sensor and validation of dynamic models applied to municipal solid waste combustion

    NARCIS (Netherlands)

    Kessel, L.B.M. van; Leskens, M.; Brem, G.

    2002-01-01

    This paper deals with two aspects concerning the optimization of municipal solid waste combustion (MSWC) processes. First of all, an on-line calorific value sensor is discussed by means of which the calorific value of the waste can be estimated from actual process data. Experimental results on a

  7. Analysis of Channel Transfer Functions in Power Line Communication System for Smart Metering and Home Area Network

    Directory of Open Access Journals (Sweden)

    MLYNEK, P.

    2016-11-01

    Full Text Available The paper deals with simulations of power line channel transfer functions in Network Simulator version 3. Firstly, an empirical model and calculation of the channel transfer function are given to reflect the necessity of channel transfer function for Power Line Communication system design. The framework for Power Line Communication in Network Simulator version 3 and then the necessary extension implementation are introduced. Other simulators are also mentioned. Secondly, various scenarios were implemented for the analysis and simulation of power line channel transfer functions. New scenarios for large topologies and for different approaches to calculate primary parameters were created. In the simulations, various kinds of topologies are considered for an analysis of the power line transfer function. The simulation part also focuses on the simulation of channel transfer function where the time- and frequency-selective impedances are considered. Finally, the last part focuses on measurements and a comparison of the simulation results with real measurements are given.

  8. Heat Transfer Model of a Small-Scale Waste Glass Melter with Cold Cap Layer

    Energy Technology Data Exchange (ETDEWEB)

    Abboud, Alexander; Guillen, Donna Post; Pokorny, Richard

    2016-09-01

    At the Hanford site in the state of Washington, more than 56 million gallons of radioactive waste is stored in underground tanks. The cleanup plan for this waste is vitrification at the Waste Treatment Plant (WTP), currently under construction. At the WTP, the waste will be blended with glass-forming materials and heated to 1423K, then poured into stainless steel canisters to cool and solidify. A fundamental understanding of the glass batch melting process is needed to optimize the process to reduce cost and decrease the life cycle of the cleanup effort. The cold cap layer that floats on the surface of the glass melt is the primary reaction zone for the feed-to-glass conversion. The conversion reactions include water release, melting of salts, evolution of batch gases, dissolution of quartz and the formation of molten glass. Obtaining efficient heat transfer to this region is crucial to achieving high rates of glass conversion. Computational fluid dynamics (CFD) modeling is being used to understand the heat transfer dynamics of the system and provide insight to optimize the process. A CFD model was developed to simulate the DM1200, a pilot-scale melter that has been extensively tested by the Vitreous State Laboratory (VSL). Electrodes are built into the melter to provide Joule heating to the molten glass. To promote heat transfer from the molten glass into the reactive cold cap layer, bubbling of the molten glass is used to stimulate forced convection within the melt pool. A three-phase volume of fluid approach is utilized to model the system, wherein the molten glass and cold cap regions are modeled as separate liquid phases, and the bubbling gas and plenum regions are modeled as one lumped gas phase. The modeling of the entire system with a volume of fluid model allows for the prescription of physical properties on a per-phase basis. The molten glass phase and the gas phase physical properties are obtained from previous experimental work. Finding representative

  9. Polybrominated diphenyl ethers in e-waste: level and transfer in a typical e-waste recycling site in Shanghai, Eastern China.

    Science.gov (United States)

    Li, Yue; Duan, Yan-Ping; Huang, Fan; Yang, Jing; Xiang, Nan; Meng, Xiang-Zhou; Chen, Ling

    2014-06-01

    Very few data for polybrominated diphenyl ethers (PBDEs) were available in the electronic waste (e-waste) as one of the most PBDEs emission source. This study reported concentrations of PBDEs in e-waste including printer, rice cooker, computer monitor, TV, electric iron and water dispenser, as well as dust from e-waste, e-waste dismantling workshop and surface soil from inside and outside of an e-waste recycling plant in Shanghai, Eastern China. The results showed that PBDEs were detected in the majority of e-waste, and the concentrations of ΣPBDEs ranged from not detected to 175 g/kg, with a mean value of 10.8 g/kg. PBDEs were found in TVs made in China after 1990. The mean concentrations of ΣPBDEs in e-waste made in Korea, Japan, Singapore and China were 1.84 g/kg, 20.5 g/kg, 0.91 g/kg, 4.48 g/kg, respectively. The levels of ΣPBDEs in e-waste made in Japan far exceed the threshold limit of RoHS (1.00 g/kg). BDE-209 dominated in e-waste, accounting for over 93%. The compositional patterns of PBDEs congeners resembled the profile of Saytex 102E, indicating the source of deca-BDE. Among the samples of dust and surface soil from a typical e-waste recycling site, the highest concentrations of Σ18PBDEs and BDE-209 were found in dust in e-waste, ranging from 1960 to 340,710 ng/g and from 910 to 320,400 ng/g, which were 1-2 orders of magnitude higher than other samples. It suggested that PBDEs released from e-waste via dust, and then transferred to surrounding environment. Copyright © 2013 Elsevier Ltd. All rights reserved.

  10. Characteristics of soil-to-plant transfer of elements relevant to radioactive waste in boreal forest

    Energy Technology Data Exchange (ETDEWEB)

    Roivainen, P.

    2011-07-01

    The use of nuclear energy generates large amounts of different types of radioactive wastes that can be accidentally released into the environment. Soil-to-plant transfer is a key process for the dispersion of radionuclides in the biosphere and is usually described by a concentration ratio (CR) between plant and soil concentrations in radioecological models. Our knowledge of the soil-to-plant transfer of many radionuclides is currently limited and concerns mainly agricultural species and temperate environments. The validity of radioecological modelling is affected by the accuracy of the assumptions and parameters used to describe soil-to-plant transfer. This study investigated the soil-to-plant transfer of six elements (cobalt (Co), molybdenum (Mo), nickel (Ni), lead (Pb), uranium (U) and zinc (Zn)) relevant to radioactive waste at two boreal forest sites and assessed the factors affecting the CR values. May lily (Maianthemum bifolium), narrow buckler fern (Dryopteris carthusiana) and blueberry (Vaccinium myrtillus) were selected as representatives of understory species, while rowan (Sorbus aucuparia) and Norway spruce (Picea abies) represented trees in this study. All the elements studied were found to accumulate in plant roots, indicating that separate CR values for root and aboveground plant parts are needed. The between-species variation in CR values was not clearly higher than the within-species variation, suggesting that the use of generic CR values for understory species and trees is justified. No linear relationship was found between soil and plant concentrations for the elements studied and a non-linear equation was found to be the best for describing the dependence of CR values on soil concentration. Thus, the commonly used assumption of a linear relationship between plant and soil concentrations may lead to underestimation of plant root uptake at low soil concentrations. Plant nutrients potassium, magnesium, manganese, phosphorus and sulphur were found to

  11. Effect of Finishing on Heat and Moisture Transfer Properties of Lining Leather for Shoes

    OpenAIRE

    角田, 由美子

    2016-01-01

      Leather lining for shoes was made from unfinished and pigment-finished glutaraldehyde-tanned leather and chrome-tanned leather prepared from pig skin. The effect of the different treatments on the heat and moisture transfer properties of the lining leather was investigated at 20℃ and 65% RH using an apparatus that simulates the microclimate of the shoes. The apparatus was developed by modeling the conditions expected during actual shoe wearing.  1. The water absorption, water vapour permeab...

  12. Heat Transfer Characteristics of Calcined Petroleum Coke in Waste Heat Recovery Process

    Directory of Open Access Journals (Sweden)

    Bin Zheng

    2016-01-01

    Full Text Available This paper reports the results of heat transfer characteristics of calcined petroleum coke in waste heat recovery process. The model of heat exchanger was set up. The model has been used to investigate the effects of porosity (0.58 to 0.79, equivalent heat conductivity coefficient (0.9 to 1.1, and equivalent specific heat (0.9 to 1.1. The calculated values of calcined petroleum coke temperature showed good agreement with the corresponding available experimental data. The temperature distribution of calcined petroleum coke, the calcined petroleum coke temperature at heat exchanger outlet, the average heat transfer coefficient, and the heat recovery efficiency were studied. It can also be used in deriving much needed data for heat exchanger designs when employed in industry.

  13. Updated layout of the LINAC4 transfer line to the PS Booster (Green Field Option)

    CERN Document Server

    Bellodi, G; Lallement, J B; Lombardi, A M; CERN. Geneva. AB Department

    2008-01-01

    At the time of defining the site of Linac4 and its integration in the complex of existing infrastructure at CERN (together with the plans for a future Superconducting Proton Linac), a series of radiation protection issues emerged that have since prompted a revision of the Linac4 to PSB transfer line layout, as was described in the document AB‐Note‐2007‐037. For radiological safety reasons the distance between the planned SPL tunnel and the basement of building 513 had to be increased, and this led to the decision to lower the Linac4 machine by 2.5m. A vertical ramp was consequently introduced in the transfer line to raise the beam at the same level of LINAC2/PSB for connection to the existing transfer line. A series of error study runs has been carried out on the modified layout to have an estimate of the losses induced by quadrupole alignment and field errors. The two worst cases of each error family have been used as case studies to test the efficiency of possible steering strategies in...

  14. Polarized ^{3}He^{+2} ions in the Alternate Gradient Synchrotron to RHIC transfer line

    Directory of Open Access Journals (Sweden)

    N. Tsoupas

    2016-09-01

    Full Text Available The proposed electron-hadron collider (eRHIC to be built at Brookhaven National Laboratory (BNL will allow the collisions of 20 GeV polarized electrons with 250 GeV polarized protons, or 100  GeV/n polarized ^{3}He^{+2} ions, or other unpolarized ion species. The large value of the anomalous magnetic moment of the ^{3}He nucleus G_{He}=(g-2/2=-4.184 (where g is the g-factor of the ^{3}He nuclear spin combined with the peculiar layout of the transfer line which transports the beam bunches from the Alternate Gradient Synchrotron (AGS to the Relativistic Heavy Ion Collider (RHIC makes the transfer and injection of polarized ^{3}He ions from AGS to RHIC (AtR a special case as we explain in the paper. Specifically in this paper we calculate the stable spin direction of a polarized ^{3}He beam at the exit of the AtR line which is also the injection point of RHIC, and we discuss a simple modifications of the AtR beam-transfer-line, to perfectly match the stable spin direction of the injected polarized ^{3}He beam to that of the circulating beam, at the injection point of RHIC.

  15. Heat transfer resistances in the measurements of cold helium vapour temperature in a subatmospheric process line

    Science.gov (United States)

    Adamczyk, A.; Pietrowicz, S.; Fydrych, J.

    2017-02-01

    The superfluid helium technology, which is essentially used in particle accelerators, requires complex cryogenic systems that include long lines transferring cold helium vapours at a subathmospheric pressure below 50 mbar. Usually in large systems the subatmospheric pressure is generated by a set of warm and cold compressors. In consequence, the heat loads to the line and especially the helium temperature in the inlet to the cold compressors are crucial parameters. In order to measure the helium temperature the temperature sensors are usually fixed to the external surface of the process lines. However, this technique can lead to unwanted measurement errors and affect the temperature measurement dynamics mainly due to low thermal conductivity of the pipe wall material, large pipe diameters and low helium density. Assembling a temperature sensor in a well (cold finger) reaching the centerline of the flowing helium is a technique that can improve the measurement quality and dynamics (response time). The paper presents the numerical simulations of heat transfers occurring in the both measurement techniques and discusses the impacts of the heat transfer resistances on the temperature measurement dynamics.

  16. Heat and Mass Transfer Remote Control in Bioreactors of Technological Lines

    Directory of Open Access Journals (Sweden)

    Viktorija M. Mel’nick

    2017-10-01

    Full Text Available Background. The main problems that arise when using equipment for cultivation are to ensure the heat and mass transfer processes in devices, presence of turbulent and stagnant zones, high-energy consumption, low heat transfer coefficients when working with viscous fluids. Objective. The aim of the paper is the experimental determination of the remote control heat transfer advantages in production line bioreactors using ultrasonic beam compared to contact methods. Methods. An experimental study of the heat and mass transfer process in a bioreactor on the stand with UZP-6-1 immersion unit of the ultrasonic radiator with radiation frequency 42 kHz is carried out. Results. Sound waves emitted into a liquid form a concentration zone of passable sound energy in the confocal vessel form of a cylindrical surface and force the liquid to move along the inner surface of the glass along the ascending cylindrical spiral, forming a motive flow throughout the volume, causing peripheral layers of liquid and bottom layers to move in a horizontal and vertical planes, without leaving stagnant zones. The closer to the coincidence angle is the directed ultrasonic beam the greater is the effectiveness of the driving flow. Conclusions. The use of sound waves allows obtaining a high-quality product in technological lines based on bioreactors with minimal risk for the technological process. Radiation parameters and working volume physic-mechanical properties change allow fully using the properties of resonant manifestations of the sound wave influence on the working liquid with minimal costs.

  17. Waste not, want not : Talisman's use of waste heat good for the environment and the bottom line

    Energy Technology Data Exchange (ETDEWEB)

    Wells, P.

    2010-10-15

    This article discussed a small-scale waste heat recovery unit (WHRU) that Talisman Energy Inc. introduced to its Bigstone natural gas plant near Fox Creek, Alberta. The unit has reduced carbon dioxide emissions along with fuel consumption and costs. The WHRU unit transfers heat produced by gas turbine compressors and uses it to heat liquids needed for processing natural gas. The project was devised and implemented after the company successfully developed a large-scale co-generation plant at its sour gas plant in Alberta. This co-generation plant reduces carbon dioxide emissions by 23,000 tonnes annually, lessens the plant's fuel gas consumption by 1 million cubic feet a day, produces 10 megawatts of electrical power, and allows the plant to continue operations when the main power grid experiences interruptions. In contrast, the Bigstone project is a small-scale application. At the start, the WHRU at Bigstone reduced fuel gas requirements by 300,000 cubic feet per day (a savings of 15 percent) and carbon dioxide emissions by 4,500 tonnes per year. The system had yet to reach its full capacity. A stabilizer for condensate was then added to the system, doubling the environmental benefit of the project. Small-scale co-generation projects can be difficult to make economic, but they have greater applicability at existing gas plants in Alberta than large-scale projects. 1 fig.

  18. Mathematical modelling of antimicrobial resistance in agricultural waste highlights importance of gene transfer rate.

    Science.gov (United States)

    Baker, Michelle; Hobman, Jon L; Dodd, Christine E R; Ramsden, Stephen J; Stekel, Dov J

    2016-04-01

    Antimicrobial resistance is of global concern. Most antimicrobial use is in agriculture; manures and slurry are especially important because they contain a mix of bacteria, including potential pathogens, antimicrobial resistance genes and antimicrobials. In many countries, manures and slurry are stored, especially over winter, before spreading onto fields as organic fertilizer. Thus, these are a potential location for gene exchange and selection for resistance. We develop and analyse a mathematical model to quantify the spread of antimicrobial resistance in stored agricultural waste. We use parameters from a slurry tank on a UK dairy farm as an exemplar. We show that the spread of resistance depends in a subtle way on the rates of gene transfer and antibiotic inflow. If the gene transfer rate is high, then its reduction controls resistance, while cutting antibiotic inflow has little impact. If the gene transfer rate is low, then reducing antibiotic inflow controls resistance. Reducing length of storage can also control spread of resistance. Bacterial growth rate, fitness costs of carrying antimicrobial resistance and proportion of resistant bacteria in animal faeces have little impact on spread of resistance. Therefore, effective treatment strategies depend critically on knowledge of gene transfer rates. © FEMS 2016. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

  19. Analysis of Mass Transfer Resistance for Adsorption of Phosphate onto Industrial Waste Materials in Plug-flow column

    Directory of Open Access Journals (Sweden)

    Khamidun Mohd Hairul

    2017-01-01

    Full Text Available The understanding resistance of mass transfer for adsorption of phosphate (PO43- onto industrial waste such as clay brick and ceramic as an adsorbent is important to verify. This study presented the removal of (PO43- from a synthetic solution by adsorbing onto the clay brick and ceramic wastes in a plug flow column (PFC. The experimental results showed that increasing the flow rate was decreases the breakthrough time. The mass transfer factor (MTF models were used to study the behaviours of breakthrough curve and to determine the resistance of mass transfer. The MTF models verified that the resistance of mass transfer could be dependent on porous diffusion until the percentage of outflow reaches 72% for clay brick waste and 86% for ceramic waste, even though film mass transfer can play a minor role in controlling the movement of (PO43- from the bulk water to film zone. The results of MTF models coefficient could be indicated to increase the capacity of clay brick and ceramic wastes to adsorb (PO43- from synthetic solution, it needs to develop the porosity of these adsorbents by either physical or chemical modification.

  20. Polybrominated diphenyl ethers in e-waste: Level and transfer in a typical e-waste recycling site in Shanghai, Eastern China

    Energy Technology Data Exchange (ETDEWEB)

    Li, Yue; Duan, Yan-Ping, E-mail: duanyanping@tongji.edu.cn; Huang, Fan; Yang, Jing; Xiang, Nan; Meng, Xiang-Zhou; Chen, Ling

    2014-06-01

    Highlights: • PBDEs were detected in the majority of e-waste. • PBDEs were found in TVs made in China after 1990. • The levels of ΣPBDEs in e-waste made in Japan far exceed the threshold limit of RoHS. • The inappropriate recycling and disposal of e-waste is an important source of PBDEs. - Abstract: Very few data for polybrominated diphenyl ethers (PBDEs) were available in the electronic waste (e-waste) as one of the most PBDEs emission source. This study reported concentrations of PBDEs in e-waste including printer, rice cooker, computer monitor, TV, electric iron and water dispenser, as well as dust from e-waste, e-waste dismantling workshop and surface soil from inside and outside of an e-waste recycling plant in Shanghai, Eastern China. The results showed that PBDEs were detected in the majority of e-waste, and the concentrations of ΣPBDEs ranged from not detected to 175 g/kg, with a mean value of 10.8 g/kg. PBDEs were found in TVs made in China after 1990. The mean concentrations of ΣPBDEs in e-waste made in Korea, Japan, Singapore and China were 1.84 g/kg, 20.5 g/kg, 0.91 g/kg, 4.48 g/kg, respectively. The levels of ΣPBDEs in e-waste made in Japan far exceed the threshold limit of RoHS (1.00 g/kg). BDE-209 dominated in e-waste, accounting for over 93%. The compositional patterns of PBDEs congeners resembled the profile of Saytex 102E, indicating the source of deca-BDE. Among the samples of dust and surface soil from a typical e-waste recycling site, the highest concentrations of Σ{sub 18}PBDEs and BDE-209 were found in dust in e-waste, ranging from 1960 to 340,710 ng/g and from 910 to 320,400 ng/g, which were 1–2 orders of magnitude higher than other samples. It suggested that PBDEs released from e-waste via dust, and then transferred to surrounding environment.

  1. A technique for transferring a patient's smile line to a cone beam computed tomography (CBCT) image.

    Science.gov (United States)

    Bidra, Avinash S

    2014-08-01

    Fixed implant-supported prosthodontic treatment for patients requiring a gingival prosthesis often demands that bone and implant levels be apical to the patient's maximum smile line. This is to avoid the display of the prosthesis-tissue junction (the junction between the gingival prosthesis and natural soft tissues) and prevent esthetic failures. Recording a patient's lip position during maximum smile is invaluable for the treatment planning process. This article presents a simple technique for clinically recording and transferring the patient's maximum smile line to cone beam computed tomography (CBCT) images for analysis. The technique can help clinicians accurately determine the need for and amount of bone reduction required with respect to the maximum smile line and place implants in optimal positions. Copyright © 2014 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.

  2. The Local Helium Compound Transfer Lines for the Large Hadron Collider Cryogenic System

    CERN Document Server

    Parente, C; Munday, A; Wiggins, P

    2006-01-01

    The cryogenic system for the Large Hadron Collider (LHC) under construction at CERN will include twelve new local helium transfer lines distributed among five LHC points in underground caverns. These lines, being manufactured and installed by industry, will connect the cold boxes of the 4.5-K refrigerators and the 1.8-K refrigeration units to the cryogenic interconnection boxes. The lines have a maximum of 30-m length and may possess either small or large re-distribution units to allow connection to the interface ports. Due to space restrictions the lines may have complex routings and require several elbowed sections. The lines consist of a vacuum jacket, a thermal shield and either three or four helium process pipes. Specific internal and external supporting and compensation systems were designed for each line to allow for thermal contraction of the process pipes (or vacuum jacket, in case of a break in the insulation vacuum) and to minimise the forces applied to the interface equipment. Whenever possible, f...

  3. Numerical Modeling of the Transient Chilldown Process of a Cryogenic Propellant Transfer Line

    Science.gov (United States)

    Hartwig, Jason; Vera, Jerry

    2015-01-01

    Before cryogenic fuel depots can be fully realized, efficient methods with which to chill down the spacecraft transfer line and receiver tank are required. This paper presents numerical modeling of the chilldown of a liquid hydrogen tank-to-tank propellant transfer line using the Generalized Fluid System Simulation Program (GFSSP). To compare with data from recently concluded turbulent LH2 chill down experiments, seven different cases were run across a range of inlet liquid temperatures and mass flow rates. Both trickle and pulse chill down methods were simulated. The GFSSP model qualitatively matches external skin mounted temperature readings, but large differences are shown between measured and predicted internal stream temperatures. Discrepancies are attributed to the simplified model correlation used to compute two-phase flow boiling heat transfer. Flow visualization from testing shows that the initial bottoming out of skin mounted sensors corresponds to annular flow, but that considerable time is required for the stream sensor to achieve steady state as the system moves through annular, churn, and bubbly flow. The GFSSP model does adequately well in tracking trends in the data but further work is needed to refine the two-phase flow modeling to better match observed test data.

  4. Successful beam test of the SPS-to-LHC transfer line TI2

    CERN Multimedia

    2007-01-01

    Image of the first beam spot on the last BTV screen traversed by the beam during the TI 2 test.At 12:03:47 on 28 October a beam passed down the 2.7 km of the new SPS-to-LHC transfer line TI 2 at the first attempt, to within some 50 m of the LHC tunnel. After initial tuning, a range of measurements was carried out with a low intensity proton beam and preliminary analyses look good. After the test, no increase in radiation levels was found in either the LHC or ALICE, and the zones were rapidly opened again for access. As from next year TI 2 will regularly transport a beam from the SPS to the LHC injection point of Ring 1, near Point 2 (ALICE). The TI 8 transfer line, which will bring particles from the SPS to the injection point in Ring 2, near Point 8 (LHCb), was commissioned successfully with low intensity beam in 2004. The two LHC injection lines have a combined length of 5.6 km and comprise some seven hundred warm magnets. While a...

  5. Assessing Ink Transfer Performance of Gravure-Offset Fine-Line Circuitry Printing

    Science.gov (United States)

    Cheng, Hsien-Chie; Chen, You-Wei; Chen, Wen-Hwa; Lu, Su-Tsai; Lin, Shih-Ming

    2017-12-01

    In this study, the printing mechanism and performance of gravure-offset fine-line circuitry printing technology are investigated in terms of key printing parameters through experimental and theoretical analyses. First, the contact angles of the ink deposited on different substrates, blankets, and gravure metal plates are experimentally determined; moreover, their temperature and solvent content dependences are analyzed. Next, the ink solvent absorption and evaporation behaviors of the blankets at different temperatures, times, and numbers of printing repetitions are characterized by conducting experiments. In addition, while printing repeatedly, the surface characteristics of the blankets, such as the contact angle, vary with the amount of absorbed ink solvent, further affecting the ink transfer performance (ratio) and printing quality. Accordingly, the surface effect of the blanket due to ink solvent absorption on the ink contact angle is analyzed. Furthermore, the amount of ink transferred from the gravure plate to the blanket in the "off process" and from the blanket to the substrate in the "set process" is evaluated by conducting a simplified plate-to-plate experiment. The influences of loading rate (printing velocity), temperature, and solvent content on the ink transfer performance are addressed. Finally, the ink transfer mechanism is theoretically analyzed for different solvent contents using Surface Evolver. The calculation results are compared with those of the experiment.

  6. Mineralogical analysis of dust collected from typical recycling line of waste printed circuit boards.

    Science.gov (United States)

    Wang, Fangfang; Zhao, Yuemin; Zhang, Tao; Duan, Chenlong; Wang, Lizhang

    2015-09-01

    As dust is one of the byproducts originating in the mechanical recycling process of waste printed circuit boards such as crushing and separating, from the viewpoints of resource reuse and environmental protection, an effective recycling method to recover valuable materials from this kind of dust is in urgent need. In this paper, detailed mineralogical analysis on the dust collected from a typical recycling line of waste printed circuit boards is investigated by coupling several analytical techniques. The results demonstrate that there are 73.1wt.% organic matters, 4.65wt.% Al, 4.55wt.% Fe, 2.67wt.% Cu and 1.06wt.% Pb in the dust, which reveals the dust is worthy of reuse and harmful to environment. The concentration ratios of Fe, Mn and Zn can reach 12.35, 12.33 and 6.67 respectively by magnetic separation. The yield of dust in each size fraction is nonuniform, while the yield of -0.75mm size fraction is up to 51.15wt.%; as the particle size decreases, the content of liberated metals and magnetic materials increase, and metals are mainly in elemental forms. The F, Cl and Br elements combing to C in the dust would make thermal treatment dangerous to the environment. Based on these results, a flowsheet to recycle the dust is proposed. Copyright © 2015 Elsevier Ltd. All rights reserved.

  7. Security camera resolution measurements: Horizontal TV lines versus modulation transfer function measurements.

    Energy Technology Data Exchange (ETDEWEB)

    Birch, Gabriel Carisle [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Griffin, John Clark [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2015-01-01

    The horizontal television lines (HTVL) metric has been the primary quantity used by division 6000 related to camera resolution for high consequence security systems. This document shows HTVL measurements are fundamen- tally insufficient as a metric to determine camera resolution, and propose a quantitative, standards based methodology by measuring the camera system modulation transfer function (MTF), the most common and accepted metric of res- olution in the optical science community. Because HTVL calculations are easily misinterpreted or poorly defined, we present several scenarios in which HTVL is frequently reported, and discuss their problems. The MTF metric is discussed, and scenarios are presented with calculations showing the application of such a metric.

  8. Alignment Compensation for Bending Radius in TI 2 Transfer Line Magnets

    CERN Document Server

    Weterings, W

    2004-01-01

    The optics file for the TI 2 transfer lines specifies the position of the bending magnets assuming that the beam enters and exists at the centre of the vacuum pipe. In order to disbribute the deflected beam evenly inside the vacuum tube, the alignment has to be compensated by moving the magnets half of the beam deflection away from the centre of the bending radius. In this note the saggitas of the various TI 2 magnets are calculated and the alignment displacements tabulated for future reference.

  9. Alignment Compensation for Bending Radius in TT40 and TI 8 Transfer Line Magnets

    CERN Document Server

    Weterings, W

    2003-01-01

    The BEATCH file for the TI 8 transfer lines specifies the position of the bending magnets assuming that the beam enters and exits at the centre of the vacuum pipe. In order to distribute the deflected beam evenly inside the vacuum tube, the alignment has to be compensated by moving the magnets half of the beam deflection away from the centre of the bending radius. In this note the saggitas of the various TT40 and TI 8 magnets are calculated and the alignment displacements tabulated for future reference.

  10. Development of buffalo (Bubalus bubalis embryonic stem cell lines from somatic cell nuclear transferred blastocysts

    Directory of Open Access Journals (Sweden)

    Syed Mohmad Shah

    2015-11-01

    Full Text Available We developed buffalo embryonic stem cell lines from somatic cell nuclear transfer derived blastocysts, produced by hand-guided cloning technique. The inner cell mass of the blastocyst was cut mechanically using a Microblade and cultured onto feeder cells in buffalo embryonic stem (ES cell culture medium at 38 °C in a 5% CO2 incubator. The stem cell colonies were characterized for alkaline phosphatase activity, karyotype, pluripotency and self-renewal markers like OCT4, NANOG, SOX2, c-Myc, FOXD3, SSEA-1, SSEA-4, TRA-1-60, TRA-1-81 and CD90. The cell lines also possessed the capability to differentiate across all the three germ layers under spontaneous differentiation conditions.

  11. Economic Analysis about the Solid Waste Quantities and Optimal Hauling Distance to Install Transfer Stations in Colombia

    OpenAIRE

    Jorge Perdomo; Juan Ramírez

    2011-01-01

    The main objective of this study is to develop an economic analysis estimating the solid waste quantities and optimal hauling distance to install transfer stations in Colombia, according to landfill location. This goal is met by using a difference in differences approach (impact evaluation technique), means panel data (random effects), comparative static analysis and mathematical optimization. These methods allowed comparing total production costs between firms with and without transfer stati...

  12. An equivalent-time-lines model for municipal solid waste based on its compression characteristics.

    Science.gov (United States)

    Gao, Wu; Bian, Xuecheng; Xu, Wenjie; Chen, Yunmin

    2017-10-01

    Municipal solid waste (MSW) demonstrates a noticeable time-dependent stress-strain behavior, which contributes greatly to the settlement of landfills and therefore influences both the storage capacity of landfills and the integrity of internal structures. The long-term compression tests for MSW under different biodegradation conditions were analyzed. It showed that the primary compression can affect the secondary compression due to the biodegradation and mechanical creep. Based on the time-lines model for clays and the compression characteristics of MSW, relationships between MSW's viscous strain rate and equivalent time were established, and then the viscous strain functions of MSW under different biodegradation conditions were deduced, and an equivalent-time-lines model for MSW settlement for two biodegradation conditions was developed, including the Type I model for the enhanced biodegradation condition and the Type II model for the normal biodegradation condition. The simulated compression results of laboratory and field compression tests under different biodegradation conditions were consistent with the measured data, which showed the reliability of both types of the equivalent-time-lines model for MSW. In addition, investigations of the long-term settlement of landfills from the literature indicated that the Type I model is suitable for predicting settlement in MSW landfills with a distinct biodegradation progress of MSW, a high content of organics in MSW, a short fill age or under an enhanced biodegradation environment; while the Type II model is good at predicting settlement in MSW landfills with a distinct progress of mechanical creep compression, a low content of organics in MSW, a long fill age or under a normal biodegradation condition. Furthermore, relationships between model parameters and the fill age of landfills were summarized. Finally, the similarities and differences between the equivalent-time-lines model for MSW and the stress

  13. Single step high-speed printing of continuous silver lines by laser-induced forward transfer

    Energy Technology Data Exchange (ETDEWEB)

    Puerto, D., E-mail: puerto@lp3.univ-mrs.fr [Aix-Marseille University, CNRS, LP3 laboratory Campus de Luminy, C.917, Marseille (France); Biver, E. [Aix-Marseille University, CNRS, LP3 laboratory Campus de Luminy, C.917, Marseille (France); Oxford Lasers Ltd., Unit 8, Moorbrook Park, Didcot, OX11 7HP (United Kingdom); Alloncle, A.-P.; Delaporte, Ph. [Aix-Marseille University, CNRS, LP3 laboratory Campus de Luminy, C.917, Marseille (France)

    2016-06-30

    Highlights: • We have performed an experimental study on laser micro-printing of silver nanoparticle inks. • We have achieved the printing of lines in a single pass at velocities of 17 m/s (1 MHz laser). • The ejection dynamics has been investigated by means of a time-resolved imaging technique. • The control of the donor film properties is of prime importance to print lines at high velocities. • Continuous conductive lines of silver inks are laser-printed on PET flexible substrates. - Abstract: The development of high-speed ink printing process by Laser-Induced Forward Transfer (LIFT) is of great interest for the printing community. To address the problems and the limitations of this process that have been previously identified, we have performed an experimental study on laser micro-printing of silver nanoparticle inks by LIFT and demonstrated for the first time the printing of continuous conductive lines in a single pass at velocities of 17 m/s using a 1 MHz repetition rate laser. We investigated the printing process by means of a time-resolved imaging technique to visualize the ejection dynamics of single and adjacent jets. The control of the donor film properties is of prime importance to achieve single step printing of continuous lines at high velocities. We use a 30 ps pulse duration laser with a wavelength of 343 nm and a repetition rate from 0.2 to 1 MHz. A galvanometric mirror head controls the distance between two consecutives jets by scanning the focused beam along an ink-coated donor substrate at different velocities. Droplets and lines of silver inks are laser-printed on glass and PET flexible substrates and we characterized their morphological quality by atomic force microscope (AFM) and optical microscope.

  14. Taiwan industrial cooperation program technology transfer for low-level radioactive waste final disposal - phase I.

    Energy Technology Data Exchange (ETDEWEB)

    Knowlton, Robert G.; Cochran, John Russell; Arnold, Bill Walter; Jow, Hong-Nian; Mattie, Patrick D.; Schelling, Frank Joseph Jr. (; .)

    2007-01-01

    Sandia National Laboratories and the Institute of Nuclear Energy Research, Taiwan have collaborated in a technology transfer program related to low-level radioactive waste (LLW) disposal in Taiwan. Phase I of this program included regulatory analysis of LLW final disposal, development of LLW disposal performance assessment capabilities, and preliminary performance assessments of two potential disposal sites. Performance objectives were based on regulations in Taiwan and comparisons to those in the United States. Probabilistic performance assessment models were constructed based on limited site data using software including GoldSim, BLT-MS, FEHM, and HELP. These software codes provided the probabilistic framework, container degradation, waste-form leaching, groundwater flow, radionuclide transport, and cover infiltration simulation capabilities in the performance assessment. Preliminary performance assessment analyses were conducted for a near-surface disposal system and a mined cavern disposal system at two representative sites in Taiwan. Results of example calculations indicate peak simulated concentrations to a receptor within a few hundred years of LLW disposal, primarily from highly soluble, non-sorbing radionuclides.

  15. Improved retroviral suicide gene transfer in colon cancer cell lines after cell synchronization with methotrexate

    Directory of Open Access Journals (Sweden)

    Nordlinger Bernard

    2011-10-01

    Full Text Available Abstract Background Cancer gene therapy by retroviral vectors is mainly limited by the level of transduction. Retroviral gene transfer requires target cell division. Cell synchronization, obtained by drugs inducing a reversible inhibition of DNA synthesis, could therefore be proposed to precondition target cells to retroviral gene transfer. We tested whether drug-mediated cell synchronization could enhance the transfer efficiency of a retroviral-mediated gene encoding herpes simplex virus thymidine kinase (HSV-tk in two colon cancer cell lines, DHDK12 and HT29. Methods Synchronization was induced by methotrexate (MTX, aracytin (ara-C or aphidicolin. Gene transfer efficiency was assessed by the level of HSV-TK expression. Transduced cells were driven by ganciclovir (GCV towards apoptosis that was assessed using annexin V labeling by quantitative flow cytometry. Results DHDK12 and HT29 cells were synchronized in S phase with MTX but not ara-C or aphidicolin. In synchronized DHDK12 and HT29 cells, the HSV-TK transduction rates were 2 and 1.5-fold higher than those obtained in control cells, respectively. Furthermore, the rate of apoptosis was increased two-fold in MTX-treated DHDK12 cells after treatment with GCV. Conclusions Our findings indicate that MTX-mediated synchronization of target cells allowed a significant improvement of retroviral HSV-tk gene transfer, resulting in an increased cell apoptosis in response to GCV. Pharmacological control of cell cycle may thus be a useful strategy to optimize the efficiency of retroviral-mediated cancer gene therapy.

  16. Targeting a newly established spontaneous feline fibrosarcoma cell line by gene transfer.

    Directory of Open Access Journals (Sweden)

    Rounak Nande

    Full Text Available Fibrosarcoma is a deadly disease in cats and is significantly more often located at classical vaccine injections sites. More rare forms of spontaneous non-vaccination site (NSV fibrosarcomas have been described and have been found associated to genetic alterations. Purpose of this study was to compare the efficacy of adenoviral gene transfer in NVS fibrosarcoma. We isolated and characterized a NVS fibrosarcoma cell line (Cocca-6A from a spontaneous fibrosarcoma that occurred in a domestic calico cat. The feline cells were karyotyped and their chromosome number was counted using a Giemsa staining. Adenoviral gene transfer was verified by western blot analysis. Flow cytometry assay and Annexin-V were used to study cell-cycle changes and cell death of transduced cells. Cocca-6A fibrosarcoma cells were morphologically and cytogenetically characterized. Giemsa block staining of metaphase spreads of the Cocca-6A cells showed deletion of one of the E1 chromosomes, where feline p53 maps. Semi-quantitative PCR demonstrated reduction of p53 genomic DNA in the Cocca-6A cells. Adenoviral gene transfer determined a remarkable effect on the viability and growth of the Cocca-6A cells following single transduction with adenoviruses carrying Mda-7/IL-24 or IFN-γ or various combination of RB/p105, Ras-DN, IFN-γ, and Mda-7 gene transfer. Therapy for feline fibrosarcomas is often insufficient for long lasting tumor eradication. More gene transfer studies should be conducted in order to understand if these viral vectors could be applicable regardless the origin (spontaneous vs. vaccine induced of feline fibrosarcomas.

  17. Targeting a Newly Established Spontaneous Feline Fibrosarcoma Cell Line by Gene Transfer

    Science.gov (United States)

    Nande, Rounak; De Carlo, Flavia; Carper, Miranda; Claudio, Charlene D.; Denvir, Jim; Valluri, Jagan; Duncan, Gary C.; Claudio, Pier Paolo

    2012-01-01

    Fibrosarcoma is a deadly disease in cats and is significantly more often located at classical vaccine injections sites. More rare forms of spontaneous non-vaccination site (NSV) fibrosarcomas have been described and have been found associated to genetic alterations. Purpose of this study was to compare the efficacy of adenoviral gene transfer in NVS fibrosarcoma. We isolated and characterized a NVS fibrosarcoma cell line (Cocca-6A) from a spontaneous fibrosarcoma that occurred in a domestic calico cat. The feline cells were karyotyped and their chromosome number was counted using a Giemsa staining. Adenoviral gene transfer was verified by western blot analysis. Flow cytometry assay and Annexin-V were used to study cell-cycle changes and cell death of transduced cells. Cocca-6A fibrosarcoma cells were morphologically and cytogenetically characterized. Giemsa block staining of metaphase spreads of the Cocca-6A cells showed deletion of one of the E1 chromosomes, where feline p53 maps. Semi-quantitative PCR demonstrated reduction of p53 genomic DNA in the Cocca-6A cells. Adenoviral gene transfer determined a remarkable effect on the viability and growth of the Cocca-6A cells following single transduction with adenoviruses carrying Mda-7/IL-24 or IFN-γ or various combination of RB/p105, Ras-DN, IFN-γ, and Mda-7 gene transfer. Therapy for feline fibrosarcomas is often insufficient for long lasting tumor eradication. More gene transfer studies should be conducted in order to understand if these viral vectors could be applicable regardless the origin (spontaneous vs. vaccine induced) of feline fibrosarcomas. PMID:22666387

  18. Radiative transfer and spectroscopic databases: A line-sampling Monte Carlo approach

    Science.gov (United States)

    Galtier, Mathieu; Blanco, Stéphane; Dauchet, Jérémi; El Hafi, Mouna; Eymet, Vincent; Fournier, Richard; Roger, Maxime; Spiesser, Christophe; Terrée, Guillaume

    2016-03-01

    Dealing with molecular-state transitions for radiative transfer purposes involves two successive steps that both reach the complexity level at which physicists start thinking about statistical approaches: (1) constructing line-shaped absorption spectra as the result of very numerous state-transitions, (2) integrating over optical-path domains. For the first time, we show here how these steps can be addressed simultaneously using the null-collision concept. This opens the door to the design of Monte Carlo codes directly estimating radiative transfer observables from spectroscopic databases. The intermediate step of producing accurate high-resolution absorption spectra is no longer required. A Monte Carlo algorithm is proposed and applied to six one-dimensional test cases. It allows the computation of spectrally integrated intensities (over 25 cm-1 bands or the full IR range) in a few seconds, regardless of the retained database and line model. But free parameters need to be selected and they impact the convergence. A first possible selection is provided in full detail. We observe that this selection is highly satisfactory for quite distinct atmospheric and combustion configurations, but a more systematic exploration is still in progress.

  19. Inhibition of protease-resistant prion protein formation in a transformed deer cell line infected with chronic wasting disease

    NARCIS (Netherlands)

    Raymond, G.J.; Olsen, E.A.; Lee, K.S.; Raymond, L.D.; Bryant, P.K.; Baron, G.S.; Caughey, W.S.; Kocisko, D.A.; McHolland, L.E.; Favara, C.; Langeveld, J.P.M.; Zijderveld, van F.G.; Mayer, R.T.; Miller, M.W.; Williams, E.S.; Caughey, B.

    2006-01-01

    Chronic wasting disease (CWD) is an emerging transmissible spongiform encephalopathy (prion disease) of North American cervids, i.e., mule deer, white-tailed deer, and elk (wapiti). To facilitate in vitro studies of CWD, we have developed a transformed deer cell line that is persistently infected

  20. Mass balance evaluation of polybrominated diphenyl ethers in landfill leachate and potential for transfer from e-waste.

    Science.gov (United States)

    Danon-Schaffer, Monica N; Mahecha-Botero, Andrés; Grace, John R; Ikonomou, Michael

    2013-09-01

    Previous research on brominated flame retardants (BFRs), including polybrominated diphenyl ethers (PBDEs) has largely focussed on their concentrations in the environment and their adverse effects on human health. This paper explores their transfer from waste streams to water and soil. A comprehensive mass balance model is developed to track polybrominated diphenyl ethers (PBDEs), originating from e-waste and non-e-waste solids leaching from a landfill. Stepwise debromination is assumed to occur in three sub-systems (e-waste, aqueous leachate phase, and non-e-waste solids). Analysis of landfill samples and laboratory results from a solid-liquid contacting chamber are used to estimate model parameters to simulate an urban landfill system, for past and future scenarios. Sensitivity tests to key model parameters were conducted. Lower BDEs require more time to disappear than high-molecular weight PBDEs, since debromination takes place in a stepwise manner, according to the simplified reaction scheme. Interphase mass transfer causes the decay pattern to be similar in all three sub-systems. The aqueous phase is predicted to be the first sub-system to eliminate PBDEs if their input to the landfill were to be stopped. The non-e-waste solids would be next, followed by the e-waste sub-system. The model shows that mass transfer is not rate-limiting, but the evolution over time depends on the kinetic degradation parameters. Experimental scatter makes model testing difficult. Nevertheless, the model provides qualitative understanding of the influence of key variables. Copyright © 2013 Elsevier B.V. All rights reserved.

  1. Experimental and analytical studies on a foam insulated rigid type transfer line for use with liquid nitrogen

    Science.gov (United States)

    Patidar, Jyotish; Sumanth, R. A.; Behera, Upendra; Kasthurirengan, Srinivasan

    2017-02-01

    The transfer line is one of the important components of any cryogenic system needed to transport the cryogenic fluid from one location to another. Towards our efforts to develop a long rigid-type transfer line for liquid nitrogen (LN2) to transfer this fluid from a 5000 litre capacity vertical storage tank to the Helium liquefier (Linde Model 1610) located at a distance of nearly 50 m, we designed and fabricated several units of straight section transfer lines of length ≈ 6.5 m and they were integrated to make the long length transfer line. Each unit was fabricated with 0.5 inch dia. copper inner tube supported by spacers within 2 inch dia. PVC outer tube. Each section was foam insulated after the necessary instrumentation for temperature measurements. The individual sub units were integrated together with a small bellow section in between to take care of thermal contraction during use. We present here the analytical and experimental studies of the cool down and mass flow characteristics of a single foam insulated unit. These experimental studies are representative results of the performances of the long length rigid foam insulated transfer line.

  2. Mass balance evaluation of polybrominated diphenyl ethers in landfill leachate and potential for transfer from e-waste

    Energy Technology Data Exchange (ETDEWEB)

    Danon-Schaffer, Monica N. [Department of Chemical and Biological Engineering, University of British Columbia, 2360 East Mall, Vancouver, Canada V6T 1Z3 (Canada); Tetra Tech, 800-555 West Hastings Street, Vancouver, Canada V6B 1M1 (Canada); Mahecha-Botero, Andrés, E-mail: andresm@chbe.ubc.ca [Department of Chemical and Biological Engineering, University of British Columbia, 2360 East Mall, Vancouver, Canada V6T 1Z3 (Canada); Grace, John R. [Department of Chemical and Biological Engineering, University of British Columbia, 2360 East Mall, Vancouver, Canada V6T 1Z3 (Canada); Ikonomou, Michael [Institute of Ocean Sciences, P.O. Box 6000, 9860 West Saanich Road, Sidney, B.C., Canada V8L 4B2 (Canada)

    2013-09-01

    Previous research on brominated flame retardants (BFRs), including polybrominated diphenyl ethers (PBDEs) has largely focussed on their concentrations in the environment and their adverse effects on human health. This paper explores their transfer from waste streams to water and soil. A comprehensive mass balance model is developed to track polybrominated diphenyl ethers (PBDEs), originating from e-waste and non-e-waste solids leaching from a landfill. Stepwise debromination is assumed to occur in three sub-systems (e-waste, aqueous leachate phase, and non-e-waste solids). Analysis of landfill samples and laboratory results from a solid-liquid contacting chamber are used to estimate model parameters to simulate an urban landfill system, for past and future scenarios. Sensitivity tests to key model parameters were conducted. Lower BDEs require more time to disappear than high-molecular weight PBDEs, since debromination takes place in a stepwise manner, according to the simplified reaction scheme. Interphase mass transfer causes the decay pattern to be similar in all three sub-systems. The aqueous phase is predicted to be the first sub-system to eliminate PBDEs if their input to the landfill were to be stopped. The non-e-waste solids would be next, followed by the e-waste sub-system. The model shows that mass transfer is not rate-limiting, but the evolution over time depends on the kinetic degradation parameters. Experimental scatter makes model testing difficult. Nevertheless, the model provides qualitative understanding of the influence of key variables. - Graphical abstract: Schematic of the various mass transfer (MT) and input/output steps for sub-systems in the landfill model. NeWS is defined as non-electronic waste solids, including sand and soil added as cover materials. Highlights: • A comprehensive mass balance model is developed to track polybrominated diphenyl ethers (PBDEs). • Landfill samples and laboratory results are used to estimate the model

  3. Time rather than sleep appears to enhance off-line learning and transfer of learning of an implicit continuous task.

    Science.gov (United States)

    Al-Sharman, Alham; Siengsukon, Catherine F

    2014-01-01

    There is increasing evidence that sleep promotes off-line enhancement of a variety of explicitly learned motor tasks in young adults. However, whether sleep promotes off-line consolidation of implicitly learned motor tasks is still under question. Furthermore, the role of sleep in promoting transfer of learning remains unknown. This study examined the role of sleep in learning and transfer of learning of an implicit continuous motor task. Twenty-three neurologically intact individuals (mean age 26.4 years) were randomly assigned to either a sleep group or a no-sleep group. The sleep group practiced a continuous tracking task in the evening and underwent retention and transfer testing the following morning, while the no-sleep group practiced the tracking task in the morning and underwent retention and transfer testing in the evening. The results show that in both the sleep and no-sleep groups, performance improved off-line without further practice for both the general skill and the sequence-specific skill. The results also indicate that sleep and time promote transfer of learning of both sequence-specific and general skill learning to a spatial and temporal variation of the motor task. These findings demonstrate that sleep does not play a critical role in promoting off-line learning and transfer of learning of an implicit continuous motor task.

  4. Tetrahedral node for Transmission-Line Modeling (TLM) applied to Bio-heat Transfer.

    Science.gov (United States)

    Milan, Hugo F M; Gebremedhin, Kifle G

    2016-12-01

    Transmission-Line Modeling (TLM) is a numerical method used to solve complex and time-domain bio-heat transfer problems. In TLM, parallelepipeds are used to discretize three-dimensional problems. The drawback in using parallelepiped shapes is that instead of refining only the domain of interest, a large additional domain would also have to be refined, which results in increased computational time and memory space. In this paper, we developed a tetrahedral node for TLM applied to bio-heat transfer that does not have the drawback associated with the parallelepiped node. The model includes heat source, blood perfusion, boundary conditions and initial conditions. The boundary conditions could be adiabatic, temperature, heat flux, or convection. The predicted temperature and heat flux were compared against results from an analytical solution and the results agreed within 2% for a mesh size of 69,941 nodes and a time step of 5ms. The method was further validated against published results of maximum skin-surface temperature difference in a breast with and without tumor and the results agreed within 6%. The published results were obtained from a model that used parallelepiped TLM node. An open source software, TLMBHT, was written using the theory developed herein and is available for download free-of-charge. Copyright © 2016 Elsevier Ltd. All rights reserved.

  5. Triangular node for Transmission-Line Modeling (TLM) applied to bio-heat transfer.

    Science.gov (United States)

    Milan, Hugo F M; Gebremedhin, Kifle G

    2016-12-01

    Transmission-Line Modeling (TLM) is a numerical method used to solve complex and time-domain bio-heat transfer problems. In TLM, rectangles are used to discretize two-dimensional problems. The drawback in using rectangular shapes is that instead of refining only the domain of interest, a large additional domain will also be refined in the x and y axes, which results in increased computational time and memory space. In this paper, we developed a triangular node for TLM applied to bio-heat transfer that does not have the drawback associated with the rectangular nodes. The model includes heat source, blood perfusion (advection), boundary conditions and initial conditions. The boundary conditions could be adiabatic, temperature, heat flux, or convection. A matrix equation for TLM, which simplifies the solution of time-domain problems or solves steady-state problems, was also developed. The predicted results were compared against results obtained from the solution of a simplified two-dimensional problem, and they agreed within 1% for a mesh length of triangular faces of 59µm±9µm (mean±standard deviation) and a time step of 1ms. Copyright © 2016 Elsevier Ltd. All rights reserved.

  6. New Single Shot Beam Position Monitor of the GSI High Energy Transfer Line

    CERN Document Server

    Schölles, J

    2005-01-01

    In the near future, single bunch handling with intensities from 104 up to 1012 particles and minimum lengths of 50 ns are expected at the GSI high energy transfer line. Thus, the demand of an accurate realtime position monitoring is mandatory. At the moment, a recently developed amplifier optimised for the best common mode amplification covers a dynamic range from nearly -80 dBm up to +20 dBm and a bandwidth of 200 MHz. To gain the required dynamic range of 160 dB, an improvement of the amplifiers is necessary. The data acquisition shall be done by commercial DSOs which have a sample rate of 2 GS/s on each of the four channels for every PU. This DSO based solution is cheap in comparison to the usage of other available sampling units. The data transfer from the DSOs to the operating stuff is foreseen via Ethernet. Amplifier controlling and position calculation happens at the control centre with LabVIEW. First results measured at the GSI synchrotron will be presented.

  7. System Performance Testing of the Pulse-Echo Ultrasonic Instrument for Critical Velocity Determination during Hanford Tank Waste Transfer Operations - 13584

    Energy Technology Data Exchange (ETDEWEB)

    Denslow, Kayte M.; Bontha, Jagannadha R.; Adkins, Harold E.; Jenks, Jeromy W.J.; Hopkins, Derek F. [Pacific Northwest National Laboratory, Richland, Washington 99354 (United States); Thien, Michael G.; Kelly, Steven E.; Wooley, Theodore A. [Washington River Protection Solutions, Richland, Washington 99354 (United States)

    2013-07-01

    The delivery of Hanford double-shell tank waste to the Hanford Tank Waste Treatment and Immobilization Plant (WTP) is governed by specific Waste Acceptance Criteria that are identified in ICD 19 - Interface Control Document for Waste Feed. Waste must be certified as acceptable before it can be delivered to the WTP. The fluid transfer velocity at which solid particulate deposition occurs in waste slurry transport piping (critical velocity) is a key waste acceptance parameter that must be accurately characterized to determine if the waste is acceptable for transfer to the WTP. Washington River Protection Solutions and the Pacific Northwest National Laboratory have been evaluating the ultrasonic PulseEcho instrument since 2010 for its ability to detect particle settling and determine critical velocity in a horizontal slurry transport pipeline for slurries containing particles with a mean particle diameter of =14 micrometers (μm). In 2012 the PulseEcho instrument was further evaluated under WRPS' System Performance test campaign to identify critical velocities for slurries that are expected to be encountered during Hanford tank waste retrieval operations or bounding for tank waste feed. This three-year evaluation has demonstrated the ability of the ultrasonic PulseEcho instrument to detect the onset of critical velocity for a broad range of physical and rheological slurry properties that are likely encountered during the waste feed transfer operations between the Hanford tank farms and the WTP. (authors)

  8. System Performance Testing of the Pulse-Echo Ultrasonic Instrument for Critical Velocity Determination during Hanford Tank Waste Transfer Operations - 13584

    Energy Technology Data Exchange (ETDEWEB)

    Denslow, Kayte M.; Bontha, Jagannadha R.; Adkins, Harold E.; Jenks, Jeromy WJ; Hopkins, Derek F.; Thien, Michael G.; Kelly, Steven E.; Wooley, Theodore A.

    2013-06-01

    The delivery of Hanford double-shell tank waste to the Hanford Tank Waste Treatment and Immobilization Plant (WTP) is governed by specific Waste Acceptance Criteria that are identified in ICD 19 - Interface Control Document for Waste Feed. Waste must be certified as acceptable before it can be delivered to the WTP. The fluid transfer velocity at which solid particulate deposition occurs in waste slurry transport piping (critical velocity) is a key waste acceptance parameter that must be accurately characterized to determine if the waste is acceptable for transfer to the WTP. Washington River Protection Solutions and the Pacific Northwest National Laboratory have been evaluating the ultrasonic PulseEcho instrument since 2010 for its ability to detect particle settling and determine critical velocity in a horizontal slurry transport pipeline for slurries containing particles with a mean particle diameter of ≥14 micrometers (μm). In 2012 the PulseEcho instrument was further evaluated under WRPS’ System Performance test campaign to identify critical velocities for slurries that are expected to be encountered during Hanford tank waste retrieval operations or bounding for tank waste feed. This three-year evaluation has demonstrated the ability of the ultrasonic PulseEcho instrument to detect the onset of critical velocity for a broad range of physical and rheological slurry properties that are likely encountered during the waste feed transfer operations between the Hanford tank farms and the WTP.

  9. ALARA Review of the Spallation Neutron Source Accumulator Ring and Transfer Lines

    Energy Technology Data Exchange (ETDEWEB)

    Haire, M.J.

    2003-06-30

    The Spallation Neutron Source (SNS) is designed to meet the growing need for new tools that will deepen our understanding in materials science, life science, chemistry, fundamental and nuclear physics, earth and environmental sciences, and engineering sciences. The SNS is an accelerator-based neutron-scattering facility that when operational will produce an average beam power of 2 MW at a repetition rate of 60 Hz. The accelerator complex consists of the front-end systems, which will include an ion source; a 1-GeV full-energy linear accelerator; a single accumulator ring and its transfer lines; and a liquid mercury target. This report documents an as-low-as-reasonably-achievable (ALARA) review of the accumulator ring and transfer lines at their early design stage. An ALARA working group was formed and conducted a review of the SNS ring and transfer lines at the {approx}25% complete design stage to help ensure that ALARA principles are being incorporated into the design. The radiological aspects of the SNS design criteria were reviewed against regulatory requirements and ALARA principles. Proposed features and measures were then reviewed against the SNS design criteria. As part of the overall review, the working group reviewed the design manual; design drawings and process and instrumentation diagrams; the environment, safety, and health manual; and other related reports and literature. The group also talked with SNS design engineers to obtain explanations of pertinent subject matter. The ALARA group found that ALARA principles are indeed being incorporated into the early design stage. Radiation fields have been characterized, and shielding calculations have been performed. Radiological issues are being adequately addressed with regard to equipment selection, access control, confinement structure and ventilation, and contamination control. Radiation monitoring instrumentation for worker and environment protection are also being considered--a good practice at this

  10. Low flux submerged membrane bioreactor treating high strength leachate from a solid waste transfer station.

    Science.gov (United States)

    Thanh, Bui Xuan; Dan, Nguyen Phuoc; Visvanathan, Chettiyappan

    2013-08-01

    A submerged membrane bioreactor was employed to treat high strength leachate generating from a solid waste transfer station. The reactor was operated at low fluxes of 1.2; 2.4; 3.8 and 5.1 LMH. The organic loading rate (OLR) ranged from 2 to 10 kg COD/m(3)day. Results show that 97% removal efficiency of COD at flux of 2.4 LMH. The highest removal of ammonia nitrogen and total nitrogen was 92.0 ± 1.5% and 88.0 ± 2.0% respectively at flux of 3.8 LMH. Fouling rates were observed to be 0.075; 0.121; 3.186 and 6.374 kPa/day for the fluxes of 1.2; 2.4; 3.8 and 5.1 LMH, respectively. Membrane fouled very slowly at low flux operation. The sustainable flux was identified to be less than 2.4 LMH for treating high strength leachate. It reveals less fouling was able to achieve for high strength wastewater by reducing the membrane flux. Copyright © 2013 Elsevier Ltd. All rights reserved.

  11. Upgrades to the SPS-to-LHC Transfer Line Beam Stoppers for the LHC High-Luminosity Era

    CERN Document Server

    Kain, Verena; Fraser, Matthew; Goddard, Brennan; Meddahi, Malika; Perillo Marcone, Antonio; Steele, Genevieve; Velotti, Francesco

    2016-01-01

    Each of the 3 km long transfer lines between the SPS and the LHC is equipped with two beam stoppers (TEDs), one at the beginning of the line and one close to the LHC injection point, which need to absorb the full transferred beam. The beam stoppers are used for setting up the SPS extractions and transfer lines with beam without having to inject into the LHC. Energy deposition and thermo-mechanical simulations have, however, shown that the TEDs will not be robust enough to safely absorb the high intensity beams foreseen for the high-luminosity LHC era. This paper will summarize the simulation results and limitations for upgrading the beam stoppers. An outline of the hardware upgrade strategy for the TEDs together with modifications to the SPS extraction interlock system to enforce intensity limitations for beam on the beam stoppers will be given.

  12. Time rather than sleep appears to enhance off-line learning and transfer of learning of an implicit continuous task

    Directory of Open Access Journals (Sweden)

    Al-Sharman A

    2014-03-01

    Full Text Available Alham Al-Sharman, Catherine F Siengsukon Department of Physical Therapy and Rehabilitation Science, University of Kansas Medical Center, Kansas City, KS, USA Abstract: There is increasing evidence that sleep promotes off-line enhancement of a variety of explicitly learned motor tasks in young adults. However, whether sleep promotes off-line consolidation of implicitly learned motor tasks is still under question. Furthermore, the role of sleep in promoting transfer of learning remains unknown. This study examined the role of sleep in learning and transfer of learning of an implicit continuous motor task. Twenty-three neurologically intact individuals (mean age 26.4 years were randomly assigned to either a sleep group or a no-sleep group. The sleep group practiced a continuous tracking task in the evening and underwent retention and transfer testing the following morning, while the no-sleep group practiced the tracking task in the morning and underwent retention and transfer testing in the evening. The results show that in both the sleep and no-sleep groups, performance improved off-line without further practice for both the general skill and the sequence-specific skill. The results also indicate that sleep and time promote transfer of learning of both sequence-specific and general skill learning to a spatial and temporal variation of the motor task. These findings demonstrate that sleep does not play a critical role in promoting off-line learning and transfer of learning of an implicit continuous motor task. Keywords: sleep, off-line learning, implicit learning, transfer, continuous task

  13. The International Stripa Project: Technology transfer from cooperation in scientific and technological research on nuclear waste disposal

    Energy Technology Data Exchange (ETDEWEB)

    Levich, R.A. [USDOE Nevada Operations Office, Las Vegas, NV (USA). Yucca Mountain Project Office; Patera, E.S. [Los Alamos National Lab., NM (USA); Ferrigan, P.M. [USDOE Chicago Operations Office, Argonne, IL (USA); Wilkey, P.L. [CER Corp., Argonne, IL (USA)

    1990-04-01

    The Nuclear Energy Agency of the organization for Economic Cooperation and Development (OECD/NEA) sponsors the International Stripa Project. The objectives of the Stripa Project are to develop techniques for characterizing sites located deep in rock formations that are potentially suitable for the geologic disposal of high-level radioactive wastes and to evaluate particular engineering design considerations that could enhance the long-term safety of a high-level radioactive waste repository in a geologic medium. The purpose of this paper is to briefly summarize the research conducted at Stripa and discuss the ways in which the technology developed for the Stripa Project has been and will be transfered to the United States Civilian Radioactive Waste Management Program`s Yucca Mountain Project. 3 refs., 2 figs.

  14. Assessment of Available Particle Size Data to Support an Analysis of the Waste Feed Delivery System Transfer System

    Energy Technology Data Exchange (ETDEWEB)

    JEWETT, J.R.

    2000-08-10

    Available data pertaining to size distribution of the particulates in Hanford underground tank waste have been reviewed. Although considerable differences exist between measurement methods, it may be stated with 95% confidence that the median particle size does not exceed 275 {micro}m in at least 95% of the ten tanks selected as sources of HLW feed for Phase 1 vitrification in the RPP. This particle size is recommended as a design basis for the WFD transfer system.

  15. An optimization model for collection, haul, transfer, treatment and disposal of infectious medical waste: Application to a Greek region.

    Science.gov (United States)

    Mantzaras, Gerasimos; Voudrias, Evangelos A

    2017-11-01

    The objective of this work was to develop an optimization model to minimize the cost of a collection, haul, transfer, treatment and disposal system for infectious medical waste (IMW). The model calculates the optimum locations of the treatment facilities and transfer stations, their design capacities (t/d), the number and capacities of all waste collection, transport and transfer vehicles and their optimum transport path and the minimum IMW management system cost. Waste production nodes (hospitals, healthcare centers, peripheral health offices, private clinics and physicians in private practice) and their IMW production rates were specified and used as model inputs. The candidate locations of the treatment facilities, transfer stations and sanitary landfills were designated, using a GIS-based methodology. Specifically, Mapinfo software with exclusion criteria for non-appropriate areas was used for siting candidate locations for the construction of the treatment plant and calculating the distance and travel time of all possible vehicle routes. The objective function was a non-linear equation, which minimized the total collection, transport, treatment and disposal cost. Total cost comprised capital and operation costs for: (1) treatment plant, (2) waste transfer stations, (3) waste transport and transfer vehicles and (4) waste collection bins and hospital boxes. Binary variables were used to decide whether a treatment plant and/or a transfer station should be constructed and whether a collection route between two or more nodes should be followed. Microsoft excel software was used as installation platform of the optimization model. For the execution of the optimization routine, two completely different software were used and the results were compared, thus, resulting in higher reliability and validity of the results. The first software was Evolver, which is based on the use of genetic algorithms. The second one was Crystal Ball, which is based on Monte Carlo

  16. Multi-criteria GIS-based siting of transfer station for municipal solid waste: The case of Kumasi Metropolitan Area, Ghana.

    Science.gov (United States)

    Bosompem, Christian; Stemn, Eric; Fei-Baffoe, Bernard

    2016-10-01

    The increase in the quantity of municipal solid waste generated as a result of population growth in most urban areas has resulted in the difficulty of locating suitable land areas to be used as landfills. To curb this, waste transfer stations are used. The Kumasi Metropolitan Area, even though it has an engineered landfill, is faced with the problem of waste collection from the generation centres to the final disposal site. Thus in this study, multi-criteria decision analysis incorporated into a geographic information system was used to determine potential waste transfer station sites. The key result established 11 sites located within six different sub-metros. This result can be used by decision makers for site selection of the waste transfer stations after taking into account other relevant ecological and economic factors. © The Author(s) 2016.

  17. Cross Talk Analysis on Multiple Coupled Transmission Lines; (The calculation of transfer functions on multiple coupled tansmission lines in an inhomogeneous dielectric medium)

    DEFF Research Database (Denmark)

    Dalby, Arne Brejning

    1994-01-01

    A flow graph relating voltages and the forward and reflected propagation modes (¿ TEM) on multiple coupled transmission lines in an inhomogeneous dielectric medium is presented. This flow graph directy gives the different transfer functions, including S-parameters, in matrix form needed...... to calculate crosstalk on the lines. An 8 bit databus is analysed in the frequency-and time domain. This analysis shows, as expected, that crosstalk can be a problem in connection with high speed logic circuits. The same databus is also analysed using the quasi-propagation-mode method proposed by Dalby [1...

  18. A Polarized Atmospheric Radiative Transfer Model for Calculations of Spectra of the Stokes Parameters of Shortwave Radiation Based on the Line-by-Line and Monte Carlo Methods

    Directory of Open Access Journals (Sweden)

    Boris Fomin

    2012-10-01

    Full Text Available This paper presents a new version of radiative transfer model called the Fast Line-by-Line Model (FLBLM, which is based on the Line-by-Line (LbL and Monte Carlo (MC methods and rigorously treats particulate and molecular scattering alongside absorption. The advantage of this model consists in the use of the line-by-line model that allows for the computing of high-resolution spectra quite quickly. We have developed the model by taking into account the polarization state of light and carried out some validations by comparison against benchmark results. FLBLM calculates the Stokes parameters spectra of shortwave radiation in vertically inhomogeneous atmospheres. This update makes the model applicable for the assessment of cloud and aerosol influence on radiances as measured by the SW high-resolution polarization spectrometers. In sample results we demonstrate that the high-resolution spectra of the Stokes parameters contain more detailed information about clouds and aerosols than the medium- and low-resolution spectra wherein lines are not resolved. The presented model is rapid enough for many practical applications (e.g., validations and might be useful especially for the remote sensing. FLBLM is suitable for development of the reliable technique for retrieval of optical and microphysical properties of clouds and aerosols from high-resolution satellites data.

  19. Effect of heterogeneity and anisotropy related to the construction method on transfer processes in waste rock piles

    Science.gov (United States)

    Lahmira, Belkacem; Lefebvre, René; Aubertin, Michel; Bussière, Bruno

    2016-01-01

    Waste rock piles producing acid mine drainage (AMD) are partially saturated systems involving multiphase (gas and liquid) flow and coupled transfer processes. Their internal structure and heterogeneous properties are inherited from their wide-ranging material grain sizes, their modes of deposition, and the underlying topography. This paper aims at assessing the effect of physical heterogeneity and anisotropy of waste rock piles on the physical processes involved in the generation of AMD. Generic waste rock pile conditions were represented with the numerical simulator TOUGH AMD based on those found at the Doyon mine waste rock pile (Canada). Models included four randomly distributed material types (coarse, intermediate, fine and very fine-grained). The term "randomly" as used in this study means that the vertical profile and spatial distribution of materials in waste rock piles (internal structure) defy stratigraphy principles applicable to natural sediments (superposition and continuity). The materials have different permeability and capillary properties, covering the typical range of materials found in waste rock piles. Anisotropy with a larger horizontal than vertical permeability was used to represent the effect of pile construction by benches, while the construction by end-dumping was presumed to induce a higher vertical than horizontal permeability. Results show that infiltrated precipitation preferentially flows in fine-grained materials, which remain almost saturated, whereas gas flows preferentially through the most permeable coarse materials, which have higher volumetric gas saturation. Anisotropy, which depends on pile construction methods, often controls global gas flow paths. Construction by benches favours lateral air entry close to the pile slope, whereas end-dumping leads to air entry from the surface to the interior of the pile by secondary gas convection cells. These results can be useful to construct and rehabilitate waste rock piles to minimize

  20. Accurate transfer maps for realistic beam-line elements: Straight elements

    Directory of Open Access Journals (Sweden)

    Chad E. Mitchell

    2010-06-01

    Full Text Available The behavior of orbits in charged-particle beam transport systems, including both linear and circular accelerators as well as final focus sections and spectrometers, can depend sensitively on nonlinear fringe-field and high-order-multipole effects in the various beam-line elements. The inclusion of these effects requires a detailed and realistic model of the interior and fringe fields, including their high spatial derivatives. A collection of surface fitting methods has been developed for extracting this information accurately from three-dimensional field data on a grid, as provided by various three-dimensional finite-element field codes. Based on these realistic field models, Lie or other methods may be used to compute accurate design orbits and accurate transfer maps about these orbits. Part I of this work presents a treatment of straight-axis magnetic elements, while part II will treat bending dipoles with large sagitta. An exactly soluble but numerically challenging model field is used to provide a rigorous collection of performance benchmarks.

  1. Natural gas large volumes measurement: going for on-line custody transfer; Medicao de grandes volumes de gas natural: rumo a transferencia de custodia on-line

    Energy Technology Data Exchange (ETDEWEB)

    Mercon, Eduardo G.; Frisoli, Caetano [PETROBRAS Transporte S.A. (TRANSPETRO), Rio de Janeiro, RJ (Brazil)

    2005-07-01

    This paper describes the structure of the natural gas flow measurement process in TRANSPETRO, and comments features and performance of existing or under-implantation equipment and systems, reviewing best practices and technology in use. This process runs through three interrelated segments: data flow measurement, strictly speaking; data transfer and acquisition; and data flow measurement certification (data consolidation to invoice). Initially, the work makes an approach to the data flow measurement segment, evaluating technical features of flow meters, and describing configurations and functions of the operating gas flow computers in TRANSPETRO's custody transfer stations. In this part it will also be presented the implantation of TRANSPETRO's system for gas chromatography data input on-line to flow computers. Further, in data transfer and acquisition, SCADA system technical aspects will be evaluated, considering communications protocols and programmable logic controllers functions in remote terminal units, and discussing their places in the measurement process. Additionally, TRANSPETRO's experience in data measurement certification tools is in discussion, as well as new upcoming tools and their potential features, from what new practices will be suggested. Finally, all the work has been conceived and carried out always aiming to the state-of-the-art technology in gas flow measurement: on-line custody transfer. (author)

  2. A mathematical model for the municipal solid waste location-routing problem with intermediate transfer stations

    Directory of Open Access Journals (Sweden)

    Hossein Asefi

    2015-09-01

    Full Text Available Municipal solid waste management is one of the challenging issues in mega cities due to various interrelated factors such as operational costs and environmental concerns. Cost as one of the most significant constraints of municipal solid waste management can be effectively economized by efficient planning approaches. Considering diverse waste types in an integrated municipal solid waste system, a mathematical model of the location-routing problem is formulated and solved in this study in order to minimize the total cost of transportation and facility establishment.

  3. On-Line analysis of gas-phase composition in the combustion chamber and particle emission characteristics during combustion of wood and waste in a small batch reactor

    OpenAIRE

    Ferge, Thomas

    2005-01-01

    On-Line analysis of gas-phase composition in the combustion chamber and particle emission characteristics during combustion of wood and waste in a small batch reactor / R. Zimmermann ... - In: Environmental science & technology. 39. 2005. S. 1393-1402

  4. Waste Conversion inton-Caprylate andn-Caproate: Resource Recovery from Wine Lees Using Anaerobic Reactor Microbiomes and In-line Extraction.

    Science.gov (United States)

    Kucek, Leo A; Xu, Jiajie; Nguyen, Mytien; Angenent, Largus T

    2016-01-01

    To convert wastes into sustainable liquid fuels and chemicals, new resource recovery technologies are required. Chain elongation is a carboxylate-platform bioprocess that converts short-chain carboxylates (SCCs) (e.g., acetate [C2] and n-butyrate [C4]) into medium-chain carboxylates (MCCs) (e.g., n-caprylate [C8] and n-caproate [C6]) with hydrogen gas as a side product. Ethanol or another electron donor (e.g., lactate, carbohydrate) is required. Competitive MCC productivities, yields (product vs. substrate fed), and specificities (product vs. all products) were only achieved previously from an organic waste material when exogenous ethanol had been added. Here, we converted a real organic waste, which inherently contains ethanol, into MCCs with n-caprylate as the target product. We used wine lees, which consisted primarily of settled yeast cells and ethanol from wine fermentation, and produced MCCs with a reactor microbiome. We operated the bioreactor at a pH of 5.2 and with continuous in-line extraction and achieved a MCC productivity of 3.9 g COD/L-d at an organic loading rate of 5.8 g COD/L-d, resulting in a promising MCC yield of 67% and specificities of 36% for each n-caprylate and n-caproate (72% for both). Compared to all other studies that used complex organic substrates, we achieved the highest n-caprylate-to-ncaproate product ratio of 1.0 (COD basis), because we used increased broth-recycle rates through the forward membrane contactor, which improved in-line extraction rates. Increased recycle rates also allowed us to achieve the highest reported MCC production flux per membrane surface area thus far (20.1 g COD/m 2 -d). Through microbial community analyses, we determined that an operational taxonomic unit (OTU) for Bacteroides spp. was dominant and was positively correlated with increased MCC productivities. Our data also suggested that the microbiome may have been shaped for improved MCC production by the high broth-recycle rates. Comparable abiotic

  5. Waste conversion into n-caprylate and n-caproate: resource recovery from wine lees using anaerobic reactor microbiomes and in-line extraction

    Directory of Open Access Journals (Sweden)

    Leo A. Kucek

    2016-11-01

    Full Text Available To convert wastes into sustainable liquid fuels and chemicals, new resource recovery technologies are required. Chain elongation is a carboxylate-platform bioprocess that converts short-chain carboxylates (SCCs (e.g., acetate C2 and n-butyrate C4 into medium-chain carboxylates (MCCs (e.g., n-caprylate C8 and n-caproate C6 with hydrogen gas as a side product. Ethanol or another electron donor (e.g., lactate, carbohydrate is required. Competitive MCC productivities, yields (product vs. substrate fed, and specificities (product vs. all products were only achieved previously from an organic waste material when exogenous ethanol had been added. Here, we converted a real organic waste, which inherently comprised of ethanol, into MCCs with n-caprylate as the target product. We used wine lees, which consisted primarily of settled yeast cells and ethanol from wine fermentation, and produced MCCs with a reactor microbiome. We operated the bioreactor at a pH of 5.2 and with continuous in-line extraction and achieved a MCC productivity of 3.9 g COD/L-d at an organic loading rate of 5.8 g COD/L-d, resulting in a promising MCC yield of 67% and specificities of 36% for each n-caprylate and n-caproate (72% for both. Compared to all other studies that used complex organic substrates, we achieved the highest n-caprylate-to-n-caproate product ratio of 1.0 (COD basis, because we used increased broth-recycle rates through the forward membrane contactor, which improved in-line extraction rates. Increased recycle rates also allowed us to achieve the highest reported MCC production flux per membrane surface area thus far (20.1 g COD/m2-d. Through microbial community analyses, we determined that an operational taxonomic unit (OTU for Bacteroides spp. was dominant and was positively correlated with increased MCC productivities. Our data also suggested that the microbiome may have been shaped for improved MCC production by the high broth-recycle rates. Comparable abiotic

  6. Characterization of the ORNL MVST Waste Tanks After Transfer of Sludge from BVEST, GAAT, and OHF Tanks

    Energy Technology Data Exchange (ETDEWEB)

    Keller, J.M.

    2001-03-23

    Over the last several years most of the sludge and liquid from the Liquid Low-Level Waste (LLLW) tanks at ORNL has been transferred and consolidated in the Melton Valley Storage Tanks (MVST). The contents of the MVST tanks at the time the sludge samples were collected for this report included the original inventory in the MVSTs along with the sludge and liquid from the Bethel Valley Evaporator Service Tanks (BVEST), Old Hydrofracture (OHF) tanks, and most of the Gunite and Associated Tanks (GAAT). During the spring and summer of 2000 the MVST composite sludge was sampled and characterized to validate the radiochemical content and to ensure regulatory compliance. This report only discusses the analytical characterization of the sludge from the MVST waste tanks (except for W-29 and W-30). The isotopic data presented in this report supports the position that fissile isotopes of uranium ({sup 233}U and {sup 235}U) and plutonium ({sup 239}Pu and {sup 241}Pu) were ''denatured'' as required by the administrative controls stated in the ORNL LLLW waste acceptance criteria (WAC). In general, the MVST sludge was found to be hazardous by RCRA characteristics based on total analysis of chromium, mercury, and lead. Also, the alpha activity due to transuranic isotopes was well above the 100 nCi/g limit for TRU waste. The characteristics of the MVST sludge relative to the WIPP WAC limits for fissile gram equivalent, plutonium equivalent activity, and thermal power from decay heat, were estimated from the data in this report and found to be far below the upper boundary for any of the remote-handled transuranic waste (RH-TRU) requirements for disposal of the waste in WIPP.

  7. Comment on "Radiative Transfer in CO2-Rich Atmospheres: 1. Collisional Line Mixing Implies a Colder Early Mars"

    Science.gov (United States)

    Turbet, M.; Tran, H.

    2017-11-01

    Ozak et al. (2016) claimed that explicitly including the effect of CO2 collisional line mixing in their radiative transfer calculations yield CO2 atmospheres that are more transparent to infrared radiation than when spectra calculations are made using sub-Lorentzian line shapes. This would in particular imply significantly colder surface temperatures (up to 15 K) for early Mars than estimated in previous studies. Here we show that the relative cooling that Ozak et al. (2016) associated to the effect of collisional line mixing is in fact due to a wrong choice of broadening species (air instead of CO2). We then calculated line-by-line spectra of pure CO2 atmospheres using a line-mixing model developed for self-broadened CO2. Using the LMD Generic model (in 1-D radiative-convective mode), we find that calculations made with the proper collisional line mixing model and with sub-Lorentzian line shapes lead to differences between early Mars surface temperatures smaller than 2 K only.

  8. Experimental study on heat transfer performance of fin-tube exchanger and PSHE for waste heat recovery

    Science.gov (United States)

    Chen, Ting; Bae, Kyung Jin; Kwon, Oh Kyung

    2018-02-01

    In this paper, heat transfer characteristics of fin-tube heat exchanger and primary surface heat exchanger (PSHE) used in waste heat recovery were investigated experimentally. The flow in the fin-tube heat exchanger is cross flow and in PSHE counter flow. The variations of friction factor and Colburn j factor with air mass flow rate, and Nu number with Re number are presented. Various comparison methods are used to evaluate heat transfer performance, and the results show that the heat transfer rate of the PSHE is on average 17.3% larger than that of fin-tube heat exchanger when air mass flow rate is ranging from 1.24 to 3.45 kg/min. However, the PSHE causes higher pressure drop, and the fin-tube heat exchanger has a wider application range which leads to a 31.7% higher value of maximum heat transfer rate compared to that of the PSHE. Besides, under the same fan power per unit frontal surface, a higher heat transfer rate value is given in the fin-tube heat exchanger.

  9. Pesticide residue analysis by off-line SPE and on-line reversed-phase LC-GC using the through-oven-transfer adsorption/desorption interface.

    Science.gov (United States)

    Perez, M; Alario, J; Vazquez, A; Villén, J

    2000-02-15

    A new method to determine pesticide residue in water is presented. The described method includes using off-line solid-phase extraction (SPE) and on-line reversed-phase liquid chromatography-gas chromatography (RPLC-GC). An interface, based on a modified programmed temperature vaporizer (PTV) injector, packed with a suitable trapping material, is used for on-line RPLC-GC. The changes made in the PTV injector affect the pneumatic system, sample introduction, and solvent elimination. The new interface is easily capable of automation. Methanol/wate (70/30) is used as the eluent in the LC preseparation step. The LC column flow during elution is different from the flow during the transfer step. The transferred volumes range from 500 to 1400 microL (volume of the fractions of interest). Solvent elimination is almost 100% before the sample reaches the GC column. The described system does not show any variation of the peak retention times. The detection limit for real samples ranges from 0.04 to 1.5 ng/L, using NP detection.

  10. RADIATIVE TRANSFER MODELING OF THE ENIGMATIC SCATTERING POLARIZATION IN THE SOLAR Na i D{sub 1} LINE

    Energy Technology Data Exchange (ETDEWEB)

    Belluzzi, Luca [Istituto Ricerche Solari Locarno, CH-6605 Locarno Monti (Switzerland); Bueno, Javier Trujillo [Instituto de Astrofísica de Canarias, E-38205 La Laguna, Tenerife (Spain); Degl’Innocenti, Egidio Landi [Dipartimento di Fisica e Astronomia, Università di Firenze, I-50125 Firenze (Italy)

    2015-12-01

    The modeling of the peculiar scattering polarization signals observed in some diagnostically important solar resonance lines requires the consideration of the detailed spectral structure of the incident radiation field as well as the possibility of ground level polarization, along with the atom's hyperfine structure and quantum interference between hyperfine F-levels pertaining either to the same fine structure J-level, or to different J-levels of the same term. Here we present a theoretical and numerical approach suitable for solving this complex non-LTE radiative transfer problem. This approach is based on the density-matrix metalevel theory (where each level is viewed as a continuous distribution of sublevels) and on accurate formal solvers of the transfer equations and efficient iterative methods. We show an application to the D-lines of Na i, with emphasis on the enigmatic D{sub 1} line, pointing out the observable signatures of the various physical mechanisms considered. We demonstrate that the linear polarization observed in the core of the D{sub 1} line may be explained by the effect that one gets when the detailed spectral structure of the anisotropic radiation responsible for the optical pumping is taken into account. This physical ingredient is capable of introducing significant scattering polarization in the core of the Na i D{sub 1} line without the need for ground-level polarization.

  11. Safety evaluation for packaging for onsite transfer of B Plant organic waste

    Energy Technology Data Exchange (ETDEWEB)

    Mercado, M.S.

    1996-10-07

    This safety evaluation for packaging authorizes the use of a 17,500-L (4,623-gal) tank manufactured by Brenner Tank, Incorporated, to transport up to 16,221 L (4,285 gal) of radioactive organic liquid waste. The waste will be transported from the organic loading pad to a storage pad. Both pads are within the B Plant complex, but approximately 4 mi apart.

  12. Design report of the MBG main bending dipoles for the proton transfer line TT41 of CNGS

    CERN Document Server

    Schirm, K M

    2001-01-01

    This report presents the design and magnetic field models of the MBG main bending dipole for the “CERN Neutrino to Gran Sasso” transfer line TT41. The MBG are resistive iron-dominated H-type magnets of 37 mm gap height and 6.3 m core length. A coil composed of two half-coils of 6 1/2 turns each will allow for two-way series connection of the entire dipole line without external return bus-bars. The core consists of 1 mm thick low carbon steel laminations with organic insulation coating, precision punched and stacked between massive end and angular plates.

  13. Upgrades of the SPS, Transfer Line and LHC Injection Protection Devices for the HL-LHC Era

    CERN Document Server

    Mete, Ö.; Cerutti, F.; Cornelis, K.; Goddard, B.; Kain, V.; Losito, R.; Maciariello, F.L.; Meddahi, M.; Uythoven, J.; Velotti, F.M.; Gianfelice-Wendt, E.; Mereghetti, A.

    The challenging High Luminosity LHC (HL-LHC) beam requirements will lead in the future to unprecedented beam parameters along the LHC injector chain. In the SPS accelerator these requests translate into about a factor two higher intensity and brightness than the present design performance. In addition to the challenge of producing and accelerating such beams, these parameters affect the resistance of the existing equipment against beam impact. Most of the protection devices in the SPS ring, its transfer lines and the LHC injection areas will be put under operational constraints which are beyond their design specification. The equipment concerned has been reviewed and their resistance to the HL-LHC beams checked. Theoretical and simulation studies have been performed for the SPS beam scraping system, the protection devices and the dump absorbers of the SPS-to-LHC transfer lines, as well as for the LHC injection protection devices. The first results of these studies are reported, together with the future prospe...

  14. Transfer Stations for urban solid wastes. Design; Transferencia ferroviaria de residuos solidos domiciliarios. Alternativas para el diseno

    Energy Technology Data Exchange (ETDEWEB)

    Dussuel Jurado, E.

    2004-07-01

    On the basis of experience in the design of projects promoted by Spanish companies for Transfer Stations for Solid Domestic Waste (RSD) using the railway, aspects regarding location, technological alternatives, restrictions and dimensions are considered. The equipment necessary for the different options is described. The paper is concerned with the Metropolitan Area of Santiago (Chile) and comments on and discusses the regulatory restrictions laid down by the PRMS (Metropolitan Regulatory Plan for Santiago) affecting decisions on location, dimensions and design. Last of all, the costs of Transfer Stations are analysed depending on the distance from the sanitary landfill nd in comparison with the alternative by road, laying down convenience kerbs. Also analysed are the environmental advantages of the railway option as opposed to roads. (Author)

  15. On-line Technology Information System (OTIS): Solid Waste Management Technology Information Form (SWM TIF)

    Science.gov (United States)

    Levri, Julie A.; Boulanger, Richard; Hogan, John A.; Rodriguez, Luis

    2003-01-01

    Contents include the following: What is OTIS? OTIS use. Proposed implementation method. Development history of the Solid Waste Management (SWM) Technology Information Form (TIF) and OTIS. Current development state of the SWM TIF and OTIS. Data collection approach. Information categories. Critiques/questions/feedback.

  16. Automated Permanent Magnet Magnetization System for 8 GeV Transfer Line and Recycler Ring Production at Fermilab

    Science.gov (United States)

    Haggard, J. Eric

    1997-05-01

    The 8 GeV beam transfer line between the Fermilab Booster and the Main Injector and the Recycler antiproton storage ring are constructed using permanent magnet ferrite bricks surrounding a steel pole and housed inside a steel flux return shell. The transfer line consists of 51 dipoles, 67 gradient magnets, and 8 quadrupoles. The Recycler ring consists of approximately 350 gradient magnets and 60 quadrupoles. These magnet assemblies are being produced at Fermilab currently and as a part of the tooling required to produce these assemblies we have designed, built and put into production an automated permanent magnet magnetization system. The system includes a conventional B-2 type dipole, a Programmable Logic Controller (PLC) controlled brick mover, a hall-probe measurement station and a IBM Compatible P.C. for data acquisition. The system has been used in the production of the 8 GeV beam transfer line magnet assemblies each requiring several hundred individual permanent ma! gnets. This paper describes and i llustrates the design of the automated system, the data acquisition, use of FEA analysis in the design, and the experience we have had using this production system.

  17. Prior knowledge transfer across transcriptional data sets and technologies using compositional statistics yields new mislabelled ovarian cell line.

    Science.gov (United States)

    Blayney, Jaine K; Davison, Timothy; McCabe, Nuala; Walker, Steven; Keating, Karen; Delaney, Thomas; Greenan, Caroline; Williams, Alistair R; McCluggage, W Glenn; Capes-Davis, Amanda; Harkin, D Paul; Gourley, Charlie; Kennedy, Richard D

    2016-09-30

    Here, we describe gene expression compositional assignment (GECA), a powerful, yet simple method based on compositional statistics that can validate the transfer of prior knowledge, such as gene lists, into independent data sets, platforms and technologies. Transcriptional profiling has been used to derive gene lists that stratify patients into prognostic molecular subgroups and assess biomarker performance in the pre-clinical setting. Archived public data sets are an invaluable resource for subsequent in silico validation, though their use can lead to data integration issues. We show that GECA can be used without the need for normalising expression levels between data sets and can outperform rank-based correlation methods. To validate GECA, we demonstrate its success in the cross-platform transfer of gene lists in different domains including: bladder cancer staging, tumour site of origin and mislabelled cell lines. We also show its effectiveness in transferring an epithelial ovarian cancer prognostic gene signature across technologies, from a microarray to a next-generation sequencing setting. In a final case study, we predict the tumour site of origin and histopathology of epithelial ovarian cancer cell lines. In particular, we identify and validate the commonly-used cell line OVCAR-5 as non-ovarian, being gastrointestinal in origin. GECA is available as an open-source R package. © The Author(s) 2016. Published by Oxford University Press on behalf of Nucleic Acids Research.

  18. Large scale centrifuge test of a geomembrane-lined landfill subject to waste settlement and seismic loading.

    Science.gov (United States)

    Kavazanjian, Edward; Gutierrez, Angel

    2017-10-01

    A large scale centrifuge test of a geomembrane-lined landfill subject to waste settlement and seismic loading was conducted to help validate a numerical model for performance based design of geomembrane liner systems. The test was conducted using the 240g-ton centrifuge at the University of California at Davis under the U.S. National Science Foundation Network for Earthquake Engineering Simulation Research (NEESR) program. A 0.05mm thin film membrane was used to model the liner. The waste was modeled using a peat-sand mixture. The side slope membrane was underlain by lubricated low density polyethylene to maximize the difference between the interface shear strength on the top and bottom of the geomembrane and the induced tension in it. Instrumentation included thin film strain gages to monitor geomembrane strains and accelerometers to monitor seismic excitation. The model was subjected to an input design motion intended to simulate strong ground motion from the 1994 Hyogo-ken Nanbu earthquake. Results indicate that downdrag waste settlement and seismic loading together, and possibly each phenomenon individually, can induce potentially damaging tensile strains in geomembrane liners. The data collected from this test is publically available and can be used to validate numerical models for the performance of geomembrane liner systems. Published by Elsevier Ltd.

  19. Environmental monitoring and fuzzy synthetic evaluation of municipal solid waste transfer stations in Beijing in 2001-2006.

    Science.gov (United States)

    Li, Chunping; Li, Guoxue; Luo, Yiming; Li, Yanfu; Huang, Jian

    2008-01-01

    Transfer station (TS) is an integral part of present-day municipal solid waste (MSW) management systems. To provide information for the incorporation of waste facilities within the current integrated waste management system, the authors measured the existing environmental quality at five MSW TSs. Discharged wastewater, air, and noise were monitored and assayed at the five TSs in Beijing in 2001-2006 during rainy seasons (RSs) and dry seasons (DSs). Except Ammonia (NH3) and hydrogen sulfide (H2S), the analytical results of total suspended particles (TSPs), odor, noise, ammonium nitrogen (NH4(+)-N), chemical oxygen demand (COD(Cr)), biochemical oxygen demand (BOD5), suspended solid (SS), and fecal coliform concentrations were all degree-varied higher than the criteria limit in China. Using fuzzy mathematics, the environmental quality of MSW TSs in Beijing was classified into five categories, with levels of certainty of belonging to different categories and evaluations. The result indicated that the whole environmental quality of Datun TS, Majialou TS, and Xiaowuji TS, in Beijing, were bad during 2001-2006 in RSs and DSs. Except in 2002, the entire environmental quality of the Wuluju TS during 2001-2006 in RSs was poor. Only in the DSs of 2002 and 2003 was the whole environmental quality of the Wuluju TS good. The whole environmental quality of the Yamenkou TS during 2001-2006 in DSs was bad, which was lower than that of 2001-2006 DSs.

  20. Volatile trace compounds released from municipal solid waste at the transfer stage: Evaluation of environmental impacts and odour pollution.

    Science.gov (United States)

    Zhao, Yan; Lu, Wenjing; Wang, Hongtao

    2015-12-30

    Odour pollution caused by municipal solid waste is a public concern. This study quantitatively evaluated the concentration, environmental impacts, and olfaction of volatile trace compounds released from a waste transfer station. Seventy-six compounds were detected, and ethanol presented the highest releasing rate and ratio of 14.76 kg/d and 12.30 g/t of waste, respectively. Life cycle assessment showed that trichlorofluoromethane and dichlorodifluoromethane accounted for more than 99% of impact potentials to global warming and approximately 70% to human toxicity (non-carcinogenic). The major contributor for both photochemical ozone formation and ecotoxicity was ethanol. A detection threshold method was also used to evaluate odour pollution. Five compounds including methane thiol, hydrogen sulphide, ethanol, dimethyl disulphide, and dimethyl sulphide, with dilution multiples above one, were considered the critical compounds. Methane thiol showed the highest contribution to odour pollution of more than 90%, as indicated by its low threshold. Comparison of the contributions of the compounds to different environmental aspects indicated that typical pollutants varied based on specific evaluation targets and therefore should be comprehensively considered. This study provides important information and scientific methodology to elucidate the impacts of odourant compounds to the environment and odour pollution. Copyright © 2015 Elsevier B.V. All rights reserved.

  1. National economic models of industrial water use and waste treatment. [technology transfer

    Science.gov (United States)

    Thompson, R. G.; Calloway, J. A.

    1974-01-01

    The effects of air emission and solid waste restrictions on production costs and resource use by industry is investigated. A linear program is developed to analyze how resource use, production cost, and waste discharges in different types of production may be affected by resource limiting policies of the government. The method is applied to modeling ethylene and ammonia plants at the design stage. Results show that the effects of increasingly restrictive wastewater effluent standards on increased energy use were small in both plants. Plant models were developed for other industries and the program estimated effects of wastewater discharge policies on production costs of industry.

  2. Possible Removal of Mercury in Dry Flue Gas Cleaning Lines of Solid Waste Incineration Units

    OpenAIRE

    Svoboda, Karel

    2014-01-01

    Here we will focus on dry flue gas cleaning methods applied for MSW incineration. Majority of dust from the incineration is usually removed in electrostatic filters or fabric (bag) filters. Dry method of flue gas cleaning are advantageous particularly in smaller solid waste incineration units, they have usually lower capital costs and simpler operation. The dry gas cleaning methods are based on an alkali sorbent injection and fabric filters for removal of dust and solid products from cleaning...

  3. TRANSFER

    African Journals Online (AJOL)

    Abstract. Quenching of curcumine fluorescence by thionine, both immobilised in cellulose acetate occurs in accordance with the Forster mechanism of energy transfer. The rate constant of energy transfer for this donor - acceptor pair is found to be 9.4 x 109 L ' mol S1 with R0 = 37±1 Б. When this donor - acceptor pair is ...

  4. Mass Transfer Studies on Adsorption of Phenol from Wastewater Using Lantana camara, Forest Waste

    Directory of Open Access Journals (Sweden)

    C. R. Girish

    2016-01-01

    Full Text Available Adsorption is one of the important treatment methods for the removal of pollutants from wastewater. The determination of rate controlling step in the process is important in the design of the process. Therefore, in the present work, mass transfer studies were done to evaluate the rate-limiting step in the adsorption of phenol from aqueous solution onto Lantana camara. Different mass transfer models were used to find the rate-limiting step and also to find the values of external mass transfer coefficient and diffusion coefficient. The Biot number was found to investigate the importance of external mass transfer to intraparticle diffusion. From the various models studied and the Biot numbers obtained, it was found that the adsorption on Lantana camara was controlled by film diffusion. The sensitivity analysis was performed to study the significance of the model parameters on the adsorption process.

  5. Virus-Free Human Placental Cell Lines To Study Genetic Functions | NCI Technology Transfer Center | TTC

    Science.gov (United States)

    The National Institute of Child Health and Human Development's Section on Cellular Differentiation is seeking statements of capability or interest from parties interested in collaborative research to further develop, evaluate, or commercialize immortalized virus-free human placental cell lines.The National Institute of Child Health and Human Development's Section on Cellular Differentiation is seeking statements of capability or interest from parties interested in collaborative research to further develop, evaluate, or commercialize immortalized virus-free human placental cell lines.

  6. From colour photographs to black-and-white line drawings: an assessment of chimpanzees' (Pan troglodytes') transfer behaviour.

    Science.gov (United States)

    Close, James; Call, Josep

    2015-03-01

    Over two experiments, we investigated the ability of two adolescent and two adult chimpanzees to generalise a learnt, pictorial categorisation to increasingly degraded and abstract stimuli. In Experiment 2, we further assessed the ability of the adolescent chimpanzees to engage in open-ended categorisation of black-and-white line drawings. The current results confirmed and extended previous findings, showing that sub-adult chimpanzees outperform adult chimpanzees in the categorisation of pictorial stimuli, particularly when the stimuli are more degraded and abstract in nature. However, none of the four chimpanzees showed positive transfer of their category learning to a set of black-and-white line drawings, and neither of the adolescent chimpanzees evidenced reliable open-ended categorisation of the black-and-white line drawings. The latter findings suggest that both sub-adult and adult chimpanzees find it difficult to recognise black-and-white line drawings, and that open-ended categorisation of black-and-white line drawings is challenging for chimpanzees.

  7. Engineering Task Plan for Hose In Hose Transfer Lines for the Interim Stabilization Program

    Energy Technology Data Exchange (ETDEWEB)

    RUNG, M.P.

    2000-06-20

    This document is the Engineering Task Plan for the engineering, design services, planning, project integration and management support for the design, modification, installation and testing of an over ground transfer (OGT) system to support the interim stabilization of nine tanks in the 241-S/SX Tank Farms.

  8. Engineering Task Plan for Hose In Hose Transfer Lines for the Interim Stabilization Program

    Energy Technology Data Exchange (ETDEWEB)

    TORRES, T.D.

    2000-08-16

    The document is the Engineering Task Plan for the engineering, design services, planning, project integration and management support for the design, modification, installation and testing of an over ground transfer (OGT) system to support the interim stabilization of S/SX and U Tank Farms.

  9. Characteristics and risks of secondary pollutants generation during compression and transfer of municipal solid waste in Shanghai.

    Science.gov (United States)

    Wang, Xiaoyuan; Xie, Bing; Wu, Dong; Hassan, Muhammad; Huang, Changying

    2015-09-01

    The generation and seasonal variations of secondary pollutants were investigated during three municipal solid waste (MSW) compression and transfer in Shanghai, China. The results showed that the raw wastewater generated from three MSW transfer stations had pH of 4.2-6.0, COD 40,000-70,000mg/L, BOD5 15,000-25,000mg/L, ammonia nitrogen (NH3-N) 400-700mg/L, total nitrogen (TN) 600-1500mg/L, total phosphorus (TP) 50-200mg/L and suspended solids (SS) 1000-80,000mg/L. The pH, COD, BOD5 and NH3-N did not show regular change throughout the year while the concentration of TN, TP and SS were higher in summer and autumn. The animal and vegetable oil content was extremely high. The average produced raw wastewater of three transfer stations ranged from 2.3% to 8.4% of total refuse. The major air pollutants of H2S 0.01-0.17mg/m(3), NH3 0.75-1.8mg/m(3) in transfer stations, however, the regular seasonal change was not discovered. During the transfer process, the generated leachate in container had pH of 5.7-6.4, SS of 9120-32,475mg/L. The COD and BOD5 were 41,633-89,060mg/L and 18,116-34,130mg/L respectively, higher than that in the compress process. The concentration of NH3-N and TP were 587-1422mg/L and 80-216mg/L, respectively, and both increased during transfer process. H2S, VOC, CH4 and NH3 were 0.4-4mg/m(3), 7-19mg/m(3), 0-3.4% and 1-4mg/m(3), respectively. The PCA analysis showed that the production of secondary pollutants is closely related to temperature, especially CH4. Therefore, avoiding high temperature is a key means of reducing the production of gaseous pollutants. And above all else, refuse classification in source, deodorization and anti-acid corrosion are the important processes to control the secondary pollutants during compression and transfer of MSW. Copyright © 2015 Elsevier Ltd. All rights reserved.

  10. LINES

    Directory of Open Access Journals (Sweden)

    Minas Bakalchev

    2015-10-01

    Full Text Available The perception of elements in a system often creates their interdependence, interconditionality, and suppression. The lines from a basic geometrical element have become the model of a reductive world based on isolation according to certain criteria such as function, structure, and social organization. Their traces are experienced in the contemporary world as fragments or ruins of a system of domination of an assumed hierarchical unity. How can one release oneself from such dependence or determinism? How can the lines become less “systematic” and forms more autonomous, and less reductive? How is a form released from modernistic determinism on the new controversial ground? How can these elements or forms of representation become forms of action in the present complex world? In this paper, the meaning of lines through the ideas of Le Corbusier, Leonidov, Picasso, and Hitchcock is presented. Spatial research was made through a series of examples arising from the projects of the architectural studio “Residential Transformations”, which was a backbone for mapping the possibilities ranging from playfulness to exactness, as tactics of transformation in the different contexts of the contemporary world.

  11. Possibilities of mercury removal in the dry flue gas cleaning lines of solid waste incineration units.

    Science.gov (United States)

    Svoboda, Karel; Hartman, Miloslav; Šyc, Michal; Pohořelý, Michael; Kameníková, Petra; Jeremiáš, Michal; Durda, Tomáš

    2016-01-15

    Dry methods of the flue gas cleaning (for HCl and SO2 removal) are useful particularly in smaller solid waste incineration units. The amount and forms of mercury emissions depend on waste (fuel) composition, content of mercury and chlorine and on the entire process of the flue gas cleaning. In the case of high HCl/total Hg molar ratio in the flue gas, the majority (usually 70-90%) of mercury is present in the form of HgCl2 and a smaller amount in the form of mercury vapors at higher temperatures. Removal of both main forms of mercury from the flue gas is dependent on chemical reactions and sorption processes at the temperatures below approx. 340 °C. Significant part of HgCl2 and a small part of elemental Hg vapors can be adsorbed on fly ash and solid particle in the air pollution control (APC) processes, which are removed in dust filters. Injection of non-impregnated active carbon (AC) or activated lignite coke particles is able to remove mainly the oxidized Hg(2+) compounds. Vapors of metallic Hg(o) are adsorbed relatively weakly. Much better chemisorption of Hg(o) together with higher sorbent capacity is achieved by AC-based sorbents impregnated with sulfur, alkali poly-sulfides, ferric chloride, etc. Inorganic sorbents with the same or similar chemical impregnation are also applicable for deeper Hg(o) removal (over 85%). SCR catalysts convert part of Hg(o) into oxidized compounds (HgO, HgCl2, etc.) contributing to more efficient Hg removal, but excess of NH3 has a negative effect. Both forms, elemental Hg(o) and HgCl2, can be converted into HgS particles by reacting with droplets/aerosol of poly-sulfides solutions/solids in flue gas. Mercury captured in the form of water insoluble HgS is more advantageous in the disposal of solid waste from APC processes. Four selected options of the dry flue gas cleaning with mercury removal are analyzed, assessed and compared (in terms of efficiency of Hg-emission reduction and costs) with wet methods and retrofits for more

  12. Optics measurements and transfer line matching for the SPS injection of the CERN Multi-Turn Extraction beam

    CERN Document Server

    Benedetto, E; Cettour Cave, S; Follin, F; Gilardoni, S; Giovannozzi, M; Roncarolo, F

    2010-01-01

    Dispersion and beam optics measurements were carried out in the transfer line between the CERN PS and SPS for the new Multi-Turn Extraction beam. Since the extraction conditions of the four islands and the core are different and strongly dependent on the non-linear effects used to split the beam in the transverse plane, a special care was taken during the measurement campaigns. Furthermore, an appropriate strategy was devised to minimize the overall optical mismatch at SPS injection. All this led to a new optical configuration that will be presented in the paper.

  13. The Transfer of Resonance Line Polarization with Partial Frequency Redistribution in the General Hanle–Zeeman Regime

    Energy Technology Data Exchange (ETDEWEB)

    Ballester, E. Alsina; Bueno, J. Trujillo [Instituto de Astrofísica de Canarias, E-38205 La Laguna, Tenerife (Spain); Belluzzi, L., E-mail: ealsina@iac.es [Istituto Ricerche Solari Locarno, CH-6605 Locarno Monti (Switzerland)

    2017-02-10

    The spectral line polarization encodes a wealth of information about the thermal and magnetic properties of the solar atmosphere. Modeling the Stokes profiles of strong resonance lines is, however, a complex problem both from a theoretical and computational point of view, especially when partial frequency redistribution (PRD) effects need to be taken into account. In this work, we consider a two-level atom in the presence of magnetic fields of arbitrary intensity (Hanle–Zeeman regime) and orientation, both deterministic and micro-structured. Working within the framework of a rigorous PRD theoretical approach, we have developed a numerical code that solves the full non-LTE radiative transfer problem for polarized radiation, in one-dimensional models of the solar atmosphere, accounting for the combined action of the Hanle and Zeeman effects, as well as for PRD phenomena. After briefly discussing the relevant equations, we describe the iterative method of solution of the problem and the numerical tools that we have developed and implemented. We finally present some illustrative applications to two resonance lines that form at different heights in the solar atmosphere, and provide a detailed physical interpretation of the calculated Stokes profiles. We find that magneto-optical effects have a strong impact on the linear polarization signals that PRD effects produce in the wings of strong resonance lines. We also show that the weak-field approximation has to be used with caution when PRD effects are considered.

  14. The Transfer of Resonance Line Polarization with Partial Frequency Redistribution in the General Hanle-Zeeman Regime

    Science.gov (United States)

    Alsina Ballester, E.; Belluzzi, L.; Trujillo Bueno, J.

    2017-02-01

    The spectral line polarization encodes a wealth of information about the thermal and magnetic properties of the solar atmosphere. Modeling the Stokes profiles of strong resonance lines is, however, a complex problem both from a theoretical and computational point of view, especially when partial frequency redistribution (PRD) effects need to be taken into account. In this work, we consider a two-level atom in the presence of magnetic fields of arbitrary intensity (Hanle-Zeeman regime) and orientation, both deterministic and micro-structured. Working within the framework of a rigorous PRD theoretical approach, we have developed a numerical code that solves the full non-LTE radiative transfer problem for polarized radiation, in one-dimensional models of the solar atmosphere, accounting for the combined action of the Hanle and Zeeman effects, as well as for PRD phenomena. After briefly discussing the relevant equations, we describe the iterative method of solution of the problem and the numerical tools that we have developed and implemented. We finally present some illustrative applications to two resonance lines that form at different heights in the solar atmosphere, and provide a detailed physical interpretation of the calculated Stokes profiles. We find that magneto-optical effects have a strong impact on the linear polarization signals that PRD effects produce in the wings of strong resonance lines. We also show that the weak-field approximation has to be used with caution when PRD effects are considered.

  15. RESULTS FROM THE COMMISSIONING OF THE NSRL BEAM TRANSFER LINE AT BNL.

    Energy Technology Data Exchange (ETDEWEB)

    TSOUPAS,N.; BELLAVIA,S.; BONATI,R.; ET AL.

    2004-07-05

    The NASA SPACE RADIATION LABORATORY (NSRL) has been constructed and started operations at the Brookhaven National Laboratory in 2003. The NSRL facility will be used by NASA to perform radiation effect studies on materials and biological samples for the space program. The facility utilizes proton and heavy-ion beams of energies from 50 to 3000 MeVln which are accelerated by the AGS Booster synchrotron accelerator. To date, {sup 1}H, {sup 12}C, {sup 56}Fe, {sup 48}Ti, and {sup 197}Au ion beams of various magnetic rigidities have been extracted from the Booster, and transported by the NSRL beam transport line to the sample location which is located 100 m from the extraction point. The NSRL beam transport line has been designed to employ octupole magnetic elements which transform the normal (Gaussian) beam distribution at the location of the sample into a beam with rectangular cross section, and uniformly distributed over the sample. When using the octupole magnetic elements to obtain the uniform beam distribution on the sample, no beam-collimation is applied at any location along the NSRL beam transport line and the beam focusing on the sample is purely magnetic. The main subject of this paper will be the performance of the octupoles (third order optics) in obtaining uniform beam distributions at the target of the NSRL beam transport line.

  16. Aquatic bioaccumulation and trophic transfer of tetrabromobisphenol-A flame retardant introduced from a typical e-waste recycling site.

    Science.gov (United States)

    Tao, Lin; Wu, Jiang-Ping; Zhi, Hui; Zhang, Ying; Ren, Zi-He; Luo, Xiao-Jun; Mai, Bi-Xian

    2016-07-01

    While the flame retardant chemical, tetrabromobisphenol-A (TBBP-A), has been frequently detected in the environment, knowledge regarding its species-specific bioaccumulation and trophic transfer is limited, especially in the highly contaminated sites. In this study, the components of an aquatic food web, including two invertebrates, two prey fish, and one predator fish, collected from a natural pond at an electronic waste (e-waste) recycling site in South China were analyzed for TBBP-A, using liquid chromatography-tandem mass spectrometry. The aquatic species had TBBP-A concentrations ranging from 350 to 1970 pg/g wet weight, with higher concentrations in the invertebrates relative to the fish species. Field-determined bioaccumulation factors of TBBP-A in the two aquatic invertebrates were nearly or greater than 5000, suggesting that TBBP-A is highly bioaccumulative in the two species. The lipid-normalized concentrations of TBBP-A in the aquatic species were negatively correlated with the trophic levels determined from stable nitrogen isotope (δ(15)N) (r = -0.82, p = 0.09), indicating that this compound experienced trophic dilution in the current food web.

  17. The contribution of multidimensional spatial analysis to a waste management policy: implementation of the ELECTRE method for characterizing transfer centers in the region of Oran

    Science.gov (United States)

    Saidi, A.; Trache, M. A.; Khelfi, M. F.

    2016-08-01

    The social and economic activity steadily growing in our cities creates a significant waste production in constantly evolving. The management of this waste is problematic because it is the center of many issues and interests. Indeed, any action or decision to the collection, transportation, treatment and disposal of waste should be considered in the economic, social, political and especially environmental aspect. A global Geomatic solution requires implementing a GIS with powerful multidimensional spatial analysis tools that support really waste management problem. Algeria has adopted a solution of waste landfill for all urban cities. In the Oran region, it exists three Centers Controlled landfill (CET) which the most important is that of Hassi-Bounif. This center currently meeting the needs of the region is unsustainable solution at the long-term because of its rapid saturation and its geographic location, which is still far from city centers (20-30 km) implying a negative impact on the vehicle park collecting such frequent breakdowns, the rapid degradation, slow delivery time and especially the high cost of the maintenance operation. This phenomenon is aggravated by the absence of real and actual initiatives targeting the recycling and recovery of waste, which makes the CET an endpoint for all types of waste. We present in this study, the use of the ELECTRE method (Multicriteria Analysis) integrated into a GIS to characterize the impact of the implementation of transfers centers at Oran region. The results of this study will accentuate the advantages of the activation of waste warehouse closer to the city, and relieving considerably the volume of transfer towards CET. The objective of our presentation is to show the leading role of the new Geomatics tools and the multidimensional spatial analysis in the apprehension of an environmental problem such the waste management and more generally in the urban management.

  18. Heat Transfer Modeling of an Annular On-Line Spray Water Cooling Process for Electric-Resistance-Welded Steel Pipe.

    Science.gov (United States)

    Chen, Zejun; Han, Huiquan; Ren, Wei; Huang, Guangjie

    2015-01-01

    On-line spray water cooling (OSWC) of electric-resistance-welded (ERW) steel pipes can replace the conventional off-line heat treatment process and become an important and critical procedure. The OSWC process improves production efficiency, decreases costs, and enhances the mechanical properties of ERW steel pipe, especially the impact properties of the weld joint. In this paper, an annular OSWC process is investigated based on an experimental simulation platform that can obtain precise real-time measurements of the temperature of the pipe, the water pressure and flux, etc. The effects of the modes of annular spray water cooling and related cooling parameters on the mechanical properties of the pipe are investigated. The temperature evolutions of the inner and outer walls of the pipe are measured during the spray water cooling process, and the uniformity of mechanical properties along the circumferential and longitudinal directions is investigated. A heat transfer coefficient model of spray water cooling is developed based on measured temperature data in conjunction with simulation using the finite element method. Industrial tests prove the validity of the heat transfer model of a steel pipe undergoing spray water cooling. The research results can provide a basis for the industrial application of the OSWC process in the production of ERW steel pipes.

  19. Two 100 m Invar® Transfer Lines at CERN : Design Principles and Operating Experience for Helium Refrigeration

    CERN Document Server

    Claudet, S; Millet, F; Roussel, E; Sengelin, J P

    2005-01-01

    The distribution of helium for the Large Hadron Collider (LHC), at CERN, will require a large variety of transfer lines. At the time of qualification of possible technologies, Invar® was investigated as potential material for internal tubes. Intensive developments were made in industry to qualify the use of Invar® M93 and its associated welding parameters. Although all tests showed good perspective, the risk associated with the lack of proven reference turned out to be dissuasive with respect to the possible cost savings for the LHC cryogenic system. However, since DN100 transfer lines were necessary for the supply and return of a test facility over a distance of 100 m, an Invar® based solution was considered, as repair or exchange would have been less dramatic than in the LHC accelerator tunnel. After recalling the technical requirements, the required material qualification will be presented as well as the design principles and operating features. This equipment has been first cooled-down to 4.5 K and acc...

  20. submitter Superconducting transmission lines – Sustainable electric energy transfer with higher public acceptance?

    CERN Document Server

    Thomas, Heiko; Chervyakov, Alexander; Stückrad, Stefan; Salmieri, Delia; Rubbia, Carlo

    2016-01-01

    Despite the extensive research and development investments into superconducting science and technology, both at the fundamental and at the applied levels, many benefits of superconducting transmission lines (SCTL) remain unknown to the public and decision makers at large. This paper aims at informing about the progress in this important research field. Superconducting transmission lines have a tremendous size advantage and lower total electrical losses for high capacity transmission plus a number of technological advantages compared to solutions based on standard conductors. This leads to a minimized environmental impact and enables an overall more sustainable transmission of electric energy. One of the direct benefits may be an increased public acceptance due to the low visual impact with a subsequent reduction of approval time. The access of remote renewable energy (RE) sources with high-capacity transmission is rendered possible with superior efficiency. That not only translates into further reducing $CO_2...

  1. Final Report For The Erosion And Corrosion Analysis Of Waste Transfer Primary Pipeline Sections From 241-SY Tank Farm

    Energy Technology Data Exchange (ETDEWEB)

    Page, J. S.; Wyrwas, R. B.; Cooke, G. A.

    2012-10-04

    Three sections of primary transfer pipeline removed from the 241-SY Tank Farm in Hanford's 200 West area, labeled as SN-285, SN-286, and SN-278, were analyzed for the presence and amount of corrosion and erosion on the inside surface of the transfer pipe. All three sections of pipe, ranging in length between 6 and 8 in., were received at the 222-S Laboratory still in the pipe-in-pipe assembly. The annular spaces were filled with urethane foam injected into the pipes for as low as reasonably achievable (ALARA) purposes. The 3-in. primary transfer pipes were first separated from the outer encasement, 6-in. pipes. The pipes were cut into small sections, or coupons, based upon the results of a non-destructive pipe wall thickness measurement which used an ultrasonic transducer. Following removal of the foam, the coupons were subjected to a series of analytical methods utilizing both optical microscopy and scanning electron microscopy to obtain erosion and corrosion information. The ultrasonic transducer analysis of the SN-285 primary pipe did not show any thinned locations in the pipe wall which were outside the expected range for the 3-in. schedule 40 pipe of 216 mils. A coupon was cut from the thinnest area on the pipe, and analysis of the inside surface, which was in contact with the tank waste, revealed a continuous layer of corrosion ~ 100 11m (4 mils) thick under a semi-continuous layer of tank waste residue ~ 20 11m (1 mil) thick. This residue layer was composed of an amorphous phase rich in chromium, magnesium, calcium, and chlorine. Small pits were detected throughout the inside pipe surface with depths up to ~ 50 11m (2 mils). Similarly, the SN-286 primary pipe did not show, by the ultrasonic transducer measurements, any thinned locations in the pipe wall which were outside the expected range for this pipe. Analysis of the coupon cut from the pipe section showed the presence of a tank waste layer containing sodium aluminate and phases rich in iron, calcium

  2. Resonant line transfer in a fog: using Lyman-alpha to probe tiny structures in atomic gas

    Science.gov (United States)

    Gronke, Max; Dijkstra, Mark; McCourt, Michael; Peng Oh, S.

    2017-11-01

    Motivated by observational and theoretical work that suggest very small-scale (≲ 1 pc) structure in the circumgalactic medium of galaxies and in other environments, we study Lyman-α (Lyα) radiative transfer in an extremely clumpy medium with many clouds of neutral gas along the line of sight. While previous studies have typically considered radiative transfer through sightlines intercepting ≲ 10 clumps, we explored the limit of a very large number of clumps per sightline (up to fc 1000). Our main finding is that, for covering factors greater than some critical threshold, a multiphase medium behaves similarly to a homogeneous medium in terms of the emergent Lyα spectrum. The value of this threshold depends on both the clump column density and the movement of the clumps. We estimated this threshold analytically and compare our findings to radiative transfer simulations with a range of covering factors, clump column densities, radii, and motions. Our results suggest that (I) the success in fitting observed Lyα spectra using homogeneous "shell models" (and the corresponding failure of multiphase models) hints at the presence of very small-scale structure in neutral gas, which is in agreement within a number of other observations; and (II) the recurrent problems of reproducing realistic line profiles from hydrodynamical simulations may be due to their inability to resolve small-scale structure, which causes simulations to underestimate the effective covering factor of neutral gas clouds. The movie associated to Fig. B.2 is available at http://www.aanda.org

  3. Low cytotoxicity effect of dendrosome as an efficient carrier for rotavirus VP2 gene transferring into a human lung cell line : dendrosome, as a novel intranasally gene porter.

    Science.gov (United States)

    Pourasgari, Farzaneh; Ahmadian, Shahin; Salmanian, Ali Hatef; Sarbolouki, Mohammad Nabi; Massumi, Mohammad

    2009-01-01

    The efficiency of dendrosome (a gene porter) was assessed in transferring recombinant human rotavirus VP2 cDNA into A549, a human lung cell line. After gene transferring, transmission electron microscopy showed core-like particles (CLPs) formation in the transfected cells both with dendrosome and lipofectamine porters. In addition, western blotting analysis showed that the expression of VP2 gene was almost equal in the dendrosome and lipofectamine-transfected cells. Also, the cytotoxicity studies revealed that dendrosome had a lower cytotoxicity than lipofectamine. Therefore, our study may introduce dendrosome as a possible carrier for gene transferring into the human lung cell line, especially, for intranasally administration of DNA vaccines.

  4. Extraction, scrub, and strip test results for the solvent transfer to salt waste processing facility

    Energy Technology Data Exchange (ETDEWEB)

    Peters, T. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

    2017-09-07

    The Savannah River National Laboratory (SRNL) prepared approximately 240 gallons of Caustic-Side Solvent Extraction (CSSX) solvent for use at the Salt Waste Processing Facility (SWPF). An Extraction, Scrub, and Strip (ESS) test was performed on a sample of the prepared solvent using a salt solution prepared by Parsons to determine cesium distribution ratios (D(Cs)), and cesium concentration in the strip effluent (SE) and decontaminated salt solution (DSS) streams. This data will be used by Parsons to help qualify the solvent for use at the SWPF. The ESS test showed acceptable performance of the solvent for extraction, scrub, and strip operations. The extraction D(Cs) measured 15.5, exceeding the required value of 8. This value is consistent with results from previous ESS tests using similar solvent formulations. Similarly, scrub and strip cesium distribution ratios fell within acceptable ranges.

  5. Material development for waste-to-energy plants. Refractory linings. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Hede Larsen, O.

    2010-10-15

    Evaluation and SEM analysis of plant exposed, failed linings confirm over and again that failure in broad lines is linked to excess porosity, inferior quality on raw materials, detrimental reactions between raw materials and other mix constituents, volume growth reactions between base material and salt depositions, thermal stress induced crack formation, and uncontrolled craftsmanship. Extensive evaluations, calculations and considerations revealed numerous ways to execute the formulation of experimental castable mixes, of which some formed a broad base for phase I trials. Three mixes of the experimental castable phase II batches reached apparent porosities of {approx} 10% measured with alcohol, estimated to less than 8%-9% if measured in water. These results compare favourably to the open porosities measure with water of generally applied LCCs in the Danish marketplace of 15.5-16.0%. Converted to bonding phase porosities the low levels realised in experiments look rather good: 28% vs 55-57%. Salt cup tests confirm state of the art resistance. Experiments and assessment of surface oxidation of Silicon Carbide grains of three levels of purity confirm that it is impossible to stabilise SiC by pre-oxydation for the purpose of creating a thicker, protective surface layer of SiO{sub 2}. It is evident from the literature and qualified assessment that free Si, as a remnant surplus from SiC manufacture, does indeed hydrolyse in the castable basic environment under development of H{sub 2} gas bubbles adding on to unwanted porosity. Heat conductivity measurements of six different, representative products conducted by the Danish Technological Institute from 300 dec. C to 750 dec. C according to their credited calorimetric method confirm that the pre-firing to excess temperatures and subsequent measurement according to the DIN/EUN norm does indeed give misleading data of up to 45% for a castable containing {approx} 55% Silicon Carbide. Finite Element analysis confirms the

  6. Implementation of the waste management transfer act. Requirements from a regulatory point of view; Zur Umsetzung des Entsorgungsuebergangsgesetzes. Anforderungen aus regulatorischer Sicht

    Energy Technology Data Exchange (ETDEWEB)

    Mueller-Dehn, Christian [PreussenElektra GmbH, Hannover (Germany). Regulierung, Grundsatzfragen

    2017-11-15

    In future in Germany, the state will be responsible for financing and handling the interim and final storage of radioactive waste from nuclear power plants. With regard to interim storage, this objective is achieved with the provisions of the Waste Management Transfer Act. Regulatory implementation is based on these regulations. BGZ Gesellschaft fuer Zwischenlager mbH is responsible for interim storage on behalf of the Federal Government. Simultaneously with the transfer of interim storage facilities to BGZ a legal transfer of approval is carried out. Insofar as there is a technical, organisational or personnel conjunction with the nuclear power plant operation, which continues to exist beyond this deadline and is relevant for regulatory purposes, a regulation is made via a service contract with the BGZ. This ensures compliance with the licensing regulations. Irradiated fuel assemblies and the waste from reprocessing can be handed over to BGZ from 1 January 2019 onwards and waste with negligible heat generation can be disposed of as of the determination of their proper packaging.

  7. H2O heating in molecular clouds - Line transfer and thermal balance in a warm dusty medium

    Science.gov (United States)

    Takahashi, T.; Silk, J.; Hollenbach, D. J.

    1983-01-01

    An investigation is undertaken into the possibility of the heating of molecular gas through collisions with radiatively pumped H2O, in the context of the overall thermal balance of optically thick molecular clouds with embedded sources. In order to solve the line transfer equation, which includes warm dust grains, an extended method of escape probability approximation is developed in which the equilibrium gas temperature arises from the balance of heating by cosmic ray ionization of H2, and by collisions with warm dust grains and radiatively pumped H2O molecules against cooling by collisions with CO and C I. The equilibrium gas temperature for a given dust temperature strongly depends on the efficiency of the cooling species, and is therefore most sensitive to the cloud optical depth. It is less dependent, in decreasing order, on H2O abundance, gas density, and velocity dispersion.

  8. Application of integral methods to prediction of heat transfer from a nuclear waste repository

    Energy Technology Data Exchange (ETDEWEB)

    Blesch, C J; Kulacki, F A; Christensen, R N

    1983-10-01

    Integral methods have been developed and applied to the prediction of the far field thermal impact of a nuclear waste repository. Specifically, the heat balance integral has been applied to a semi-infinite layered domain in which a limited number of sublayers form the repository overburden, and the repository is represented by an infinite plane beneath either one or two sublayers. Calculations for PWR spent fuel with an initial areal thermal loading of 60 kW/acre are carried out for various stratigraphies and overburden compositions. Results of the analyses are temperature distributions and heat fluxes to the surface as a function to time. Based on this study, the thermophysical properties of the individual layers are identified as the most important influence on temperature distributions and maximum temperature rise at any position above the repository. The thicknesses of the sublayers play a secondary role for a given rock composition. Where a comparison to exact or numerical solutions is possible, the method predicts maximum temperature increases in the overburden to within 10 percent. Heat fluxes to the surface are found to be relatively insensitive to overburden composition. For dome salt, a maximum of 1.2 percent to 2.7 percent of the initial areal thermal power of a five-term source reaches the surface. For bedded salt, a maximum of 1 percent to 1.8 percent of the initial areal thermal power reaches the surface over a wide range of sublayer compositions. Similarly, low percentages of initial areal thermal power reach the surface for the other stratigraphies considered in the calculations.

  9. On-line analysis of organic compounds in diesel exhaust using a proton transfer reaction mass spectrometer (PTR-MS)

    Science.gov (United States)

    Jobson, B. T.; Alexander, M. L.; Maupin, G. D.; Muntean, G. G.

    2005-08-01

    Chemical ionization mass spectrometry using H3O+ proton transfer in an ion drift tube (PTR-MS) was used to measure volatile organic compound (VOC) concentrations on-line in diesel engine exhaust as a function of engine load. The purpose of the study was to evaluate the PTR-MS instrument as an analytical tool for diesel engine emissions abatement research. Measured sensitivities determined from gas standards were found to agree well with calculated sensitivities for non-polar species. A slight humidity dependent sensitivity was observed for non-polar species, implying that reactions with H+(H2O)2 were important for some organics. The diesel exhaust mass spectra were complex but displayed a pattern of strong ion signals at 14n + 1 (n = 3.8) masses, with a relative ion abundance similar to that obtained from electron impact ionization of alkanes. Laboratory experiments verified that C8-C16 n-alkanes and C8-C13 1-alkenes react with H3O+ in dissociative proton transfer reaction resulting in alkyl cation ion products, primarily m/z 41, 43, 57, 71 and 85. Monitoring the sum of these ion signals may be useful for estimating alkane emissions from unburnt diesel fuel. Alkane fragmentation likely simplified the diesel exhaust mass spectrum and reduced potential mass interferences with isobaric aromatic compounds. Concentrations of aldehydes and ketones dominated those of aromatic species with formaldehyde and acetaldehyde estimated to be the most abundant VOCs in the PTR-MS mass spectrum at all engine loads. The relative abundances of benzene and toluene increased with engine load indicating their pyrogenic origin. The relative abundance of alkanes, aromatics, aldehydes and alcohols was broadly consistent with literature publications of diesel exhaust analysis by gas chromatography. About 75% of the organic ion signal could be assigned. On-line analysis of diesel exhaust using this technology may be valuable tool for diesel engine emission research.

  10. Investigation of Content, Stoichiometry and Transfer of miRNA from Human Neural Stem Cell Line Derived Exosomes.

    Directory of Open Access Journals (Sweden)

    Lara Stevanato

    Full Text Available Exosomes are small (30-100 nm membrane vesicles secreted by a variety of cell types and only recently have emerged as a new avenue for cell-to-cell communication. They are natural shuttles of RNA and protein cargo, making them attractive as potential therapeutic delivery vehicles. MicroRNAs (miRNAs are short non-coding RNAs which regulate biological processes and can be found in exosomes. Here we characterized the miRNA contents of exosomes derived from human neural stem cells (hNSCs. Our investigated hNSC line is a clonal, conditionally immortalized cell line, compliant with good manufacturing practice (GMP, and in clinical trials for stroke and critical limb ischemia in the UK (clinicaltrials.gov: NCT01151124, NCT02117635, and NCT01916369. By using next generation sequencing (NGS technology we identified the presence of a variety of miRNAs in both exosomal and cellular preparations. Many of these miRNAs were enriched in exosomes indicating that cells specifically sort them for extracellular release. Although exosomes have been proven to contain miRNAs, the copy number quantification per exosome of a given miRNA remains unclear. Herein we quantified by real-time PCR a highly shuttled exosomal miRNA subtype (hsa-miR-1246 in order to assess its stoichiometry per exosome. Furthermore, we utilized an in vitro system to confirm its functional transfer by measuring the reduction in luciferase expression using a 3' untranslated region dual luciferase reporter assay. In summary, NGS analysis allowed the identification of a unique set of hNSC derived exosomal miRNAs. Stoichiometry and functional transfer analysis of one of the most abundant identified miRNA, hsa-miR-1246, were measured to support biological relevance of exosomal miRNA delivery.

  11. Conceptual design of transfer station materials and energy recovery facility, City of Berkeley, Solid Waste Management Center. Final report: executive summary

    Energy Technology Data Exchange (ETDEWEB)

    1980-01-01

    A conceptual design was developed for the Berkeley Solid Waste Management Center incorporating modular combustion units. Markets for recovered materials and energy were confirmed in the study. Additional work briefly discussed covered an analysis of the waste stream; assessment of the front-end processing technology; an identification of regulatory agency requirements and environmental constraints; preparation of preliminary design and budget cost estimates for the transfer station/modular combustion plant; development of financing and procurement arrangements; identification of project risks; and establishment of an implementation master plan.

  12. On-line slurry viscosity and concentration measurement as a real-time waste stream characterization tool. 1998 annual progress report

    Energy Technology Data Exchange (ETDEWEB)

    Powell, R.L.

    1998-06-01

    'This project seeks to develop an on-line sensor to measure the viscosity of dense slurries. This report summarizes work after two years of a three year project. The flow behavior of slurries is important for many of the proposed unit operations to be used in the conveying and processing of tank wastes. One alternative for determining the rheological properties of such materials is to obtain samples and test them off-line using conventional rheometers. Such a protocol is not practical for a wide variety of wastes. Rather, it is the goal of this work to find on-line, in-process techniques for measurement. There are two systems that the authors have propose examining: (1) Nuclear magnetic resonance imaging (NMRI), and, (2) Ultrasonic Doppler Velocimetry. Central to both of these techniques is the measurement of velocity profiles in pipe flows. For the NMRI measurements, the presence of particles has two principal effects on the NMRI velocity profiles: a decrease in signal intensity and image blurring. Similar effects are observed in turbulent flows due to the local random fluctuations in the flow. This similarity has led us to turbulent flow using NMRI. The governing equations for the signal obtained by NMRI are the Bloch-Torrey equations. Previously, the author showed a relationship between turbulent fluctuations and spatial signal intensity variations, assuming isotropic turbulence. However, this assumption does not reflect the true nature of turbulence in a pipe flow where the turbulence is not isotropic. In the new work the Bloch-Torrey equations will be solved by first, time averaging and then employing a turbulence model for pipe flow. The purpose of the time averaging is to smooth the fluctuations of time scale smaller than that of NMRI data acquisition. After this work with single phase fluids, the authors shall undertake NMRI experiments of slurry flow. Various operational parameters will be optimized during the experiments to obtain velocity profile of

  13. Joule-Heated Ceramic-Lined Melter to Vitrify Liquid Radioactive Wastes Containing Am241 Generated From MOX Fuel Fabrication in Russia

    Energy Technology Data Exchange (ETDEWEB)

    Smith, E C; Bowan II, B W; Pegg, I; Jardine, L J

    2004-11-16

    and americium it contains. Silver is widely used as an additive in glass making. However, its solubility is known to be limited in borosilicate glasses. Further, silver, which is present as a nitrate salt in the waste, can be easily reduced to molten silver in the melting process. Molten silver, if formed, would be difficult to reintroduce into the glass matrix and could pose operating difficulties for the glass melter. This will place a limitation on the waste loading of the melter feed material to prevent the separation of silver from the waste within the melter. If the silver were recovered in the MOx fabrication process, which is currently under consideration, the composition of the glass would likely be limited only by the thermal heat load from the incorporated {sup 241}Am. The resulting mass of glass used to encapsulate the waste could then be reduced by a factor of approximately three. The vitrification process used to treat the waste stream is proposed to center on a joule-heated ceramic lined slurry fed melter. Glass furnaces of this type are used in the United States to treat high-level waste (HLW) at the: Defense Waste Processing Facility, West Valley Demonstration Project, and to process the Hanford tank waste. The waste will initially be blended with glass-forming chemicals, which are primarily sand and boric acid. The resulting slurry is pumped to the melter for conversion to glass. The melter is a ceramic lined metal box that contains a molten glass pool heated by passing electric current through the glass. Molten glass from the melter is poured into canisters to cool and solidify. They are then sealed and decontaminated to form the final waste disposal package. Emissions generated in the melter from the vitrification process are treated by an off-gas system to remove radioactive contamination and destroy nitrogen oxides (NOx).

  14. The 'W' prawn-trawl with emphasised drag-force transfer to its centre line to reduce overall system drag.

    Directory of Open Access Journals (Sweden)

    Cheslav Balash

    Full Text Available For prawn trawling systems, drag reduction is a high priority as the trawling process is energy intensive. Large benefits have occurred through the use of multiple-net rigs and thin twine in the netting. An additional positive effect of these successful twine-area reduction strategies is the reduced amount of otter board area required to spread the trawl systems, which leads to further drag reduction. The present work investigated the potential of redirecting the drag-strain within a prawn trawl away from the wings and the otter boards to the centre line of the trawl, where top and bottom tongues have been installed, with an aim to minimise the loading/size of the otter boards required to spread the trawl. In the system containing the new 'W' trawl, the drag redirected to the centre-line tongues is transferred forward through a connected sled and towing wires to the trawler. To establish the extent of drag redirection to the centre-line tongues and the relative drag benefits of the new trawl system, conventional and 'W' trawls of 3.65 m headline length were tested firstly over a range of spread ratios in the flume tank, and subsequently at optimum spread ratio in the field. The developed 'W' trawl effectively directed 64% of netting-drag off the wings and onto the centre tongues, which resulted in drag savings in the field of ∼20% for the associated 'W' trawl/otter-board/sled system compared to the traditional trawl/otter-board arrangement in a single trawl or twin rig configuration. Furthermore, based on previously published data, the new trawl when used in a twin rig system is expected to provide approximately 12% drag reduction compared to quad rig. The twin 'W' trawl system also has benefits over quad rig in that a reduced number of cod-end/By-catch Reduction Device units need to be installed and attended each tow.

  15. Dispersion modeling and health risk assessment of VOCs emissions from municipal solid waste transfer station in Tehran, Iran.

    Science.gov (United States)

    Sarkhosh, Maryam; Shamsipour, AliAkbar; Yaghmaeian, Kamyar; Nabizadeh, Ramin; Naddafi, Kazem; Mohseni, Seyed Mohsen

    2017-01-01

    The waste transfer stations (WTSs) is one of the most important factors affecting on environment and human health. This research is aimed to evaluate health risk of VOCs among WTS personnel and provide a model for dispersion of VOCs. The Air Pollution Model (TAPM) is able to simulate WTS emissions dispersion over each town. GC-MS was used to analysis collected gas samples to detect and estimate carcinogenic and non-carcinogenic VOCs health risks. The total lifetime cancer risk values for the all personnel (3.30E-05), was more than acceptable limit (1.00E-06). Furthermore, hazard ratio (HR) of 1,2,3-trimethylbenzene, 1,3-dichloropropane, toluene, m,p-xylene and ethylbenzene were 3.7, 1.9 E-01, 4.4 E-03, 5.5 E-02 and 1.5 E-03, respectively, and total HR of the mentioned compounds were more than accepted limit (HR < 1.00). IOA is 0.85 and RMSE is 2.16 and TAPM has a good performance. The VOCs level is considerable in 1600 m far from the WTS particularly in summer that require more attention. The exposure to VOCs was at a high level in WTS, and some controlling strategy should be used for decreasing the pollution and protecting the citizens and personnel against non-cancerous and cancerous risks.

  16. A Monte Carlo study for the calculation of the average linear energy transfer (LET) distributions for a clinical proton beam line and a radiobiological carbon ion beam line.

    Science.gov (United States)

    Romano, F; Cirrone, G A P; Cuttone, G; Rosa, F Di; Mazzaglia, S E; Petrovic, I; Fira, A Ristic; Varisano, A

    2014-06-21

    Fluence, depth absorbed dose and linear energy transfer (LET) distributions of proton and carbon ion beams have been investigated using the Monte Carlo code Geant4 (GEometry ANd Tracking). An open source application was developed with the aim to simulate two typical transport beam lines, one used for ocular therapy and cell irradiations with protons and the other for cell irradiations with carbon ions. This tool allows evaluation of the primary and total dose averaged LET and predict their spatial distribution in voxelized or sliced geometries. In order to reproduce the LET distributions in a realistic way, and also the secondary particles' contributions due to nuclear interactions were considered in the computations. Pristine and spread-out Bragg peaks were taken into account both for proton and carbon ion beams, with the maximum energy of 62 MeV/n. Depth dose distributions were compared with experimental data, showing good agreement. Primary and total LET distributions were analysed in order to study the influence of contributions of secondary particles in regions at different depths. A non-negligible influence of high-LET components was found in the entrance channel for proton beams, determining the total dose averaged LET by the factor 3 higher than the primary one. A completely different situation was obtained for carbon ions. In this case, secondary particles mainly contributed in the tail that is after the peak. The results showed how the weight of light and heavy secondary ions can considerably influence the computation of LET depth distributions. This has an important role in the interpretation of results coming from radiobiological experiments and, therefore, in hadron treatment planning procedures.

  17. Requirements Verification Report AN Farm to 200E Waste Transfer System for Project W-314 Tank Farm Restoration and Safe Operations

    Energy Technology Data Exchange (ETDEWEB)

    MCGREW, D.L.

    1999-09-28

    This Requirements Verification Report (RVR) for Project W-314 ''AN Farm to 200E Waste Transfer System'' package provides documented verification of design compliance to all the applicable Project Development Specification (PDS) requirements. Additional PDS requirements verification will be performed during the project's procurement, construction, and testing phases, and the RVR will be updated to reflect this information as appropriate.

  18. On-line Analysis of Organic Compounds in Diesel Exhaust Using a Proton Transfer Reaction Mass Spectrometer (PTR-MS)

    Energy Technology Data Exchange (ETDEWEB)

    Jobson, B Tom T.; Alexander, M. Lizabeth; Maupin, Gary D.; Muntean, George G.

    2005-08-01

    Chemical ionization mass spectrometry using H3O+ proton transfer in an ion drift tube (PTR-MS) was used to measure volatile organic compound (VOC) concentrations on-line in diesel engine exhaust as a function on engine load. The purpose of the study was to evaluate the PTR-MS instrument as an analytical tool for diesel engine emissions abatement research. Measured sensitivities determined from gas standards were found to be between 30% and 100% greater than calculated sensitivities. A slight humidity dependent sensitivity was observed for non-polar species, implying that reactions with H+(H2O)2 were important for some organics. The mass spectra of diesel exhaust were complex but displayed a pattern of strong ion signals at 14n+1 (n=3..8) masses, with a relative ion abundance similar to that obtained from electron impact ionization of alkanes. Laboratory experiments verified that C8-C16 n-alkanes and C8-C13 1-alkenes react with H3O+ in dissociative proton transfer reaction resulting in alkyl cation ion products, primarily m/z 41, 43, 57, 71 and 85. Monitoring the sum of these ions signals may be useful for estimating alkane emissions from unburnt diesel fuel. Alkane fragmentation likely simplified the diesel exhaust mass spectrum and reduced potential mass interferences with isobaric aromatic compounds. It is shown that the relative abundances of VOCs changed as a function of engine load. Concentrations of aldehydes and ketones dominated those of aromatic species with formaldehyde and acetaldehyde estimated to be the most abundant VOCs in the PTR-MS mass spectrum at all engine loads. The relative abundances of benzene and toluene increased with engine load indicating their pyrogenic origin. The relative abundance of alkanes, aromatics, aldehydes, and alcohols was broadly consistent with literature publications of diesel exhaust analysis by gas chromatography. About 75% of the organic ion signal could be assigned. On line analysis of diesel exhaust using this

  19. Modelling and optimization of transient processes in line focusing power plants with single-phase heat transfer medium

    Science.gov (United States)

    Noureldin, K.; González-Escalada, L. M.; Hirsch, T.; Nouri, B.; Pitz-Paal, R.

    2016-05-01

    A large number of commercial and research line focusing solar power plants are in operation and under development. Such plants include parabolic trough collectors (PTC) or linear Fresnel using thermal oil or molten salt as the heat transfer medium (HTM). However, the continuously varying and dynamic solar condition represent a big challenge for the plant control in order to optimize its power production and to keep the operation safe. A better understanding of the behaviour of such power plants under transient conditions will help reduce defocusing instances, improve field control, and hence, increase the energy yield and confidence in this new technology. Computational methods are very powerful and cost-effective tools to gain such understanding. However, most simulation models described in literature assume equal mass flow distributions among the parallel loops in the field or totally decouple the flow and thermal conditions. In this paper, a new numerical model to simulate a whole solar field with single-phase HTM is described. The proposed model consists of a hydraulic part and a thermal part that are coupled to account for the effect of the thermal condition of the field on the flow distribution among the parallel loops. The model is specifically designed for large line-focusing solar fields offering a high degree of flexibility in terms of layout, condition of the mirrors, and spatially resolved DNI data. Moreover, the model results have been compared to other simulation tools, as well as experimental and plant data, and the results show very good agreement. The model can provide more precise data to the control algorithms to improve the plant control. In addition, short-term and accurate spatially discretized DNI forecasts can be used as input to predict the field behaviour in-advance. In this paper, the hydraulic and thermal parts, as well as the coupling procedure, are described and some validation results and results of simulating an example field are

  20. GEOTAIL observation of tilted X-line formation during flux transfer events (FTEs in the dayside magnetospheric boundary layers

    Directory of Open Access Journals (Sweden)

    M. Nowada

    2004-09-01

    Full Text Available The magnetic field and plasma structures during two successive crossings of the subsolar magnetospheric boundary layers (i.e. MagnetoPause Current Layer (MPCL and Low-Latitude Boundary Layer (LLBL under the southward-dawnward IMF are examined on the basis of the data obtained by the GEOTAIL spacecraft. A significant and interesting feature is found, that is, Flux Transfer Events (FTEs occur in association with the formation of the tilted X-line. During the first inbound MPCL/LLBL crossing, the ion velocity enhancement (in particular, the Vl component negatively increases can be observed in association with simultaneous typical bipolar signature (positive followed by negative in the Bn component. In addition, a clear D-shaped ion distribution whose origin is the magnetosheath can also be found in the dawnward direction. A few minutes later, the satellite experiences outbound MPCL crossing. The negative enhancement of the Vm component can be found as well as the positive enhancement of the Vl component. Simultaneously, a typical bipolar signature with the polarity (negative followed by positive opposite that observed in the first encounter can also be observed. The ions from the magnetosheath flow predominantly in the duskward direction, although the D-shaped ion distribution cannot be observed. These results indicate that the satellite initially observes one part of a reconnected flux tube formed by FTEs whose magnetospheric side is anchored to the Southern Hemisphere. The ions confined in this partial flux tube are flowing in the south-dawnward direction. Then, the satellite observes the other part of the reconnected flux tube whose magnetospheric side is anchored to the Northern Hemisphere. The ions confined in this flux tube flow dominantly in the north-duskward direction. Furthermore, it can be considered that the second MPCL crossing is a direct cut through the diffusion

  1. Most critical collimator-mask-magnet sequence in the SPS-to-LHC transfer lines: energy deposition study.

    CERN Document Server

    Marzo, Matteo; Lechner, Anton; Vlachoudis, Vasilis

    2017-01-01

    This technical note refers to a study on the relation between the impact conditions of the SPS 450GeV proton beam and the energy deposited downstream the Target Collimator Dump In- jection Long (TCDIL) collimators [1], in the SPS-to-LHC transfer lines TI2 and TI8. Such an analysis is relevant in order to simulate the worst scenario of failure, in case the beam impacts on the TCDIL collimator’s jaw, in the frame of the LHC Injectors Upgrade (LIU), in view of the High Luminosity LHC (HL-LHC) phase. Previous studies already showed the dependency of the energy deposited in the downstream masks on the collimators-masks distance [2]. In absence of a (realistic) impact parameter, we perform now a study to select the most pessimistic one, trying to understand the origin of the various components responsible for the energy deposition on the downstream mask and magnet. The set up of the Monte Carlo FLUKA [3] [4] simulations and the most relevant results will be presented in this document. A sensitivity analysis was a...

  2. EVALUATION OF BEST AVAILABLE CONTROL TECHNOLOGY FOR TOXICS -TBACT- DOUBLE SHELL TANK FARMS PRIMARY VENTILATION SYSTEMS SUPPORTING WASTE TRANSFER OPERATIONS

    Energy Technology Data Exchange (ETDEWEB)

    HAAS CC; KOVACH JL; KELLY SE; TURNER DA

    2010-06-24

    This report is an evaluation of Best Available Control Technology for Toxics (tBACT) for installation and operation of the Hanford double shell (DST) tank primary ventilation systems. The DST primary ventilation systems are being modified to support Hanford's waste retrieval, mixing, and delivery of single shell tank (SST) and DST waste through the DST storage system to the Waste Treatment and Immobilizaiton Plant (WTP).

  3. EVALUATION OF BEST AVAILABLE CONTROL TECHNOLOGY FOR TOXICS (TBACT) DOUBLE SHELL TANK FARMS PRIMARY VENTILATION SYSTEM SUPPORTING WASTE TRANSFER OPERATIONS

    Energy Technology Data Exchange (ETDEWEB)

    KELLY SE; HAASS CC; KOVACH JL; TURNER DA

    2010-06-03

    This report is an evaluation of Best Available Control Technology for Toxics (tBACT) for installation and operation of the Hanford double shell (DST) tank primary ventilation systems. The DST primary ventilation systems are being modified to support Hanford's waste retrieval, mixing, and delivery of single shell tank (SST) and DST waste throught the DST storage system to the Waste Treatment and Immobilization Plant (WTP).

  4. Free vibration analysis of straight-line beam regarded as distributed system by combining Wittrick-Williams algorithm and transfer dynamic stiffness coefficient method

    Energy Technology Data Exchange (ETDEWEB)

    Choi, Myung Soo; Yang, Kyong Uk [Chonnam National University, Yeosu (Korea, Republic of); Kondou, Takahiro [Kyushu University, Fukuoka (Japan); Bonkobara, Yasuhiro [University of Miyazaki, Miyazaki (Japan)

    2016-03-15

    We developed a method for analyzing the free vibration of a structure regarded as a distributed system, by combining the Wittrick-Williams algorithm and the transfer dynamic stiffness coefficient method. A computational algorithm was formulated for analyzing the free vibration of a straight-line beam regarded as a distributed system, to explain the concept of the developed method. To verify the effectiveness of the developed method, the natural frequencies of straight-line beams were computed using the finite element method, transfer matrix method, transfer dynamic stiffness coefficient method, the exact solution, and the developed method. By comparing the computational results of the developed method with those of the other methods, we confirmed that the developed method exhibited superior performance over the other methods in terms of computational accuracy, cost and user convenience.

  5. Advanced Learners' Comprehension of Discourse Connectives: The Role of L1 Transfer across On-Line and Off-Line Tasks

    Science.gov (United States)

    Zufferey, Sandrine; Mak, Willem; Degand, Liesbeth; Sanders, Ted

    2015-01-01

    Discourse connectives are important indicators of textual coherence, and mastering them is an essential part of acquiring a language. In this article, we compare advanced learners' sensitivity to the meaning conveyed by connectives in an off-line grammaticality judgment task and an on-line reading experiment using eye-tracking. We also assess the…

  6. Volatile organic compounds emitted after leaf wounding: On-line analysis by proton-transfer-reaction mass spectrometry

    Science.gov (United States)

    Fall, Ray; Karl, Thomas; Hansel, Armin; Jordan, Alfons; Lindinger, Werner

    1999-07-01

    Volatile organic compounds (VOCs) released from vegetation, including wound-induced VOCs, can have important effects on atmospheric chemistry. The analytical methods for measuring wound-induced VOCs, especially the hexenal family of VOCs (hexenals, hexenols, and hexenyl esters), are complicated by their chemical instability and the transient nature of their formation after leaf and stem wounding. Here we demonstrate that formation and emission of hexenal family compounds can be monitored on-line using proton-transfer-reaction mass spectrometry (PTR-MS), avoiding the need for preconcentration or chromatography. These measurements allow direct analysis of the rapid emission of the parent compound, (Z)-3-hexenal, within 1-2 s of wounding of aspen leaves and then its disappearance and the appearance of its metabolites including (E)-2-hexenal, hexenols, and hexenyl acetates. Similar results were seen in wounded beech leaves and clover. The emission of hexenal family compounds was proportional to the extent of wounding, was not dependent on light, occurred in attached or detached leaves, and was greatly enhanced as detached leaves dried out. Emission of (Z)-3-hexenal from detached drying aspen leaves averaged 500 μg C g-1 (dry leaf weight). Leaf wound compounds were not emitted in a nitrogen atmosphere but were released within seconds of reintroduction of oxygen; this indicates that there are not large pools of hexenyl compounds in leaves. The PTR-MS method also allows the simultaneous detection of less abundant hexanal family VOCs including hexanal, hexanol, and hexyl acetate and VOCs formed in the light (isoprene) or during anoxia (acetaldehyde). PTR-MS may be a useful tool for the analysis of VOC emissions resulting from grazing, herbivory, and other physical damage to vegetation, from harvesting of crops, and from senescing leaves.

  7. Rapid and sensitive on-line monitoring 6 different kinds of volatile organic compounds in aqueous samples by spray inlet proton transfer reaction mass spectrometry (SI-PTR-MS).

    Science.gov (United States)

    Zou, Xue; Kang, Meng; Wang, Hongmei; Huang, Chaoqun; Shen, Chengyin; Chu, Yannan

    2017-06-01

    Rapid and sensitive monitoring of volatile organic compounds (VOCs) in aqueous samples is very important to human health and environmental protection. In this study, an on-line spray inlet proton transfer reaction mass spectrometry (SI-PTR-MS) method was developed for the rapid and sensitive monitoring of 6 different kinds of VOCs, namely acetonitrile, acetaldehyde, ethanol, acetone, aether, and methylbenzene, in aqueous samples. The response time, limit of detection (LOD), and repeatability of the SI-PTR-MS system were evaluated. The response of the SI-PTR-MS was quite rapid with response times of 31-88 s. The LODs for all these VOCs were below 10 μg/L. The LOD of methylbenzene was 0.9 μg/L, much lower than the maximum contaminant level (MCL) in drinking water. The repeatability of this method was evaluated with 5 replicate determinations. The relative standard deviations (RSDs) were in the range of 0.8-3.1%, indicating good repeatability. To evaluate the matrix effects, the SI-PTR-MS system was employed for on-line monitoring of these 6 VOCs in different aqueous matrices, including lake water, tap water, and waste water. The relative recoveries were in the range of 94.6-106.0% for the lake water, 96.3-105.6% for the tap water, and 95.6-102.9% for the waste water. The results indicate that the SI-PTR-MS method has important application values in the rapid and sensitive monitoring of VOCs in these aqueous samples. In addition, the effect of salt concentration on the extracting efficiency was evaluated. The results showed that the LOD of the SI-PTR-MS could be further decreased by changing the salt concentration. Copyright © 2017 Elsevier Ltd. All rights reserved.

  8. Radiation protection in transference of radioactive wastes among buildings of an intermediary deposit; Radioprotecao na transferencia de rejeitos radioativos entre edificios de um deposito intermediario

    Energy Technology Data Exchange (ETDEWEB)

    Mitake, Malvina Boni; Suzuki, Fabio Fumio, E-mail: mbmitake@ipen.b, E-mail: ffsuzuki@ipen.b [Instituto de Pesquisas Energeticas e Nucleares (IPEN/-CNEN-SP), Sao Paulo, SP (Brazil). Gerencia de Radioprotecao

    2011-10-26

    This paper describes the planning of radioprotection realized for transfer operation of radioactive wastes from two old buildings for a one of the new buildings. For planning purposes the operation was divided into nine stages and, for evaluation of collective dose, it was considered various relevant factors. The result of radioprotection optimization it was expected a total collective dose of 58.6 mSv per person. The measured dose per dosemeter of direct reading was of 3.9 mSv per person. These difference among the values is due to conservative factors used in the calculation

  9. Multivariate optimization and validation studies in on-line pre-concentration system for lead determination in drinking water and saline waste from oil refinery

    OpenAIRE

    Santos, Walter L. dos; Santos, Carla M. M. dos; Costa, Jorge L. O.; Andrade, Heloysa Martins Carvalho; Ferreira, Sergio Luis Costa

    2004-01-01

    p. 123-129 The present paper proposes an on-line pre-concentration procedure for lead determination in drinking water and saline waste from oil refinery by flame atomic absorption spectrometry (FAAS). It is based on the sorption of lead (II) ions in a minicolumn of polyurethane foam loaded with 4-(2-pyridylazo)-resorcinol (PAR) reagent. The optimization step was performed using Doehlert matrix involving the variables: sampling flow rate (SR), buffer concentration (BC), pH and eluent concen...

  10. Environmental assessment operation of the HB-Line facility and frame waste recovery process for production of Pu-238 oxide at the Savannah River Site

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-04-01

    The Department of Energy (DOE) has prepared an environmental assessment (EA), DOE/EA-0948, addressing future operations of the HB-Line facility and the Frame Waste Recovery process at the Savannah River Site (SRS), near Aiken, South Carolina. Based on the analyses in the EA, DOE has determined that the proposed action is not a major Federal action significantly affecting the quality of the human environment within the meaning of the National Environmental Policy Act (NEPA) of 1969. Therefore, DOE has concluded that, the preparation of an environmental impact statement is not required, and is issuing this Finding of No Significant Impact.

  11. Establishment of line A and partial renovation of the infrastructure of the waste incinerator Berlin Ruhleben during operation; Errichtung der Linie A und teilweise Erneuerung der Infrastruktur im laufenden Betrieb der Abfallverbrennungsanlage Berlin Ruhleben

    Energy Technology Data Exchange (ETDEWEB)

    Gosten, Alexander [Berliner Stadtreinigungsbetriebe (BSR), Berlin (Germany). Abfallverwertung und -beseitigung; Hauser, Ralf; Rintel, Bernd; Hensel, Jochen [Berliner Stadtreinigungsbetriebe (BSR), Berlin (Germany). Projekt ERIN/Bunkerertuechtigung

    2013-03-01

    In the light of the implementation of the Technical Guidelines for the treatment and disposal of municipal waste, the incineration of waste materials in the thermal power plant Berlin-Ruhleben (Federal Republic of Germany) awarded a crucial importance in the waste management concept of the Land of Berlin. The contribution describes the construction of the line A and partial renovation of the infrastructure of the waste incinerator Berlin Ruhleben. First of all, the history of the former waste incinerator and the partial renovation as well as the starting situation and the basis for decision-making for replacement investments are described. Subsequently, the project ERIN is presented, in which components of the existing waste incinerator are substituted. Further aspects of this contribution are the general conditions for the development of the project organisation, requirements relative to the project organisation, accessibility of the project organization to the business unit.

  12. A new multiobjective optimal allocation of multitype FACTS devices for total transfer capability enhancement and improving line congestion using the harmony search algorithm

    OpenAIRE

    Esmaeili, Abbas; ESMAEILI, Saeid

    2014-01-01

    In this paper, a new approach based on novel heuristic algorithms is used to locate and model multitype flexible alternating current transmission system (FACTS) devices (series and parallel) in order to improve the total transfer capability and decrease the line congestion and total power loss. The multitype FACTS devices, including the static synchronous series compensator, static compensator, and unified power flow controller, have been optimally sized and located simultaneously thr...

  13. Evaluating the potential of 'on-line' constructed wetlands for mitigating pesticide transfers from agricultural land to surface waters

    Science.gov (United States)

    Whelan, Michael; Ramos, Andre; Guymer, Ian; Villa, Raffaella; Jefferson, Bruce

    2016-04-01

    Pesticides make important contributions to modern agriculture but losses from land to water can present problems for environmental management, particularly in catchments where surface waters are abstracted for drinking water. Where artificial field drains represent a dominant pathway for pesticide transfers, buffer zones provide little mitigation potential. Instead, "on-line" constructed wetlands have been proposed as a potential means of reducing pesticide fluxes in drainage ditches and headwater streams. Here, we evaluate the potential of small free-surface wetlands to reduce pesticide concentrations in surface waters using a combination of field monitoring and numerical modelling. Two small constructed wetland systems in a first order catchment in Cambridgeshire, UK, were monitored over the 2014-2015 winter season. Discharge was measured at several flow control structures and samples were collected every eight hours and analysed for metaldehyde, a commonly-used molluscicide. Metaldehyde is moderately mobile and, like many other compounds, it has been regularly detected at high concentrations in surface water samples in a number of drinking water supply catchments in the UK over the past few years. However, it is unusually difficult to remove via conventional drinking water treatment which makes it particularly problematical for water companies. Metaldehyde losses from the upstream catchment were significant with peak concentrations occurring in the first storm events in early autumn, soon after application. Concentrations and loads appeared to be unaffected by transit through the wetland over a range of flow conditions - probably due to short solute residence times (quantified via several tracing experiments employing rhodamine WT - a fluorescent dye). A dynamic model, based on fugacity concepts, was constructed to describe chemical fate in the wetland system. The model was used to evaluate mitigation potential and management options under field conditions and

  14. Comparison of Waste Feed Delivery Small Scale Mixing Demonstration Simulant to Hanford Waste

    Energy Technology Data Exchange (ETDEWEB)

    Wells, Beric E.; Gauglitz, Phillip A.; Rector, David R.

    2011-08-15

    'The Hanford double-shell tank (DST) system provides the staging location for waste feed delivery to the Hanford Tank Waste Treatment and Immobilization Plant (WTP). Hall (2008) includes WTP acceptance criteria that describe physical and chemical characteristics of the waste that must be certified as acceptable before the waste is transferred from the DSTs to the WTP. One of the more challenging requirements relates to the sampling and characterization of the undissolved solids (UDS) in a waste feed DST. The objectives of Washington River Protection Solutions' (WRPS) Small Scale Mixing Demonstration (SSMD) project are to understand and demonstrate the DST sampling and batch transfer performance at multiple scales using slurry simulants comprised of UDS particles and liquid (Townson 2009). The SSMD project utilizes geometrically scaled DST feed tanks to generate mixing, sampling, and transfer test data. In Phase 2 of the testing, RPP-49740, the 5-part simulant defined in RPP-48358 was used as the waste slurry simulant. The Phase 2 test data are being used to estimate the expected performance of the prototypic systems in the full-scale DSTs. As such, understanding of the how the small-scale systems as well as the simulant relate to the full-scale DSTs and actual waste is required. The focus of this report is comparison of the size and density of the 5-part SSMD simulant to that of the Hanford waste. This is accomplished by computing metrics for particle mobilization, suspension, settling, transfer line intake, and pipeline transfer from the characterization of the 5-part SSMD simulant and characterizations of the Hanford waste. In addition, the effects of the suspending fluid characteristics on the test results are considered, and a computational fluid dynamics tool useful to quantify uncertainties from simulant selections is discussed.'

  15. Force balance near an X line along which E x J is less than 0. [plasma transfer from closed to open field lines in geomagnetic tail

    Science.gov (United States)

    Lyons, L. R.; Pridmore-Brown, D. C.

    1992-01-01

    Conditions for which particle motion within the current sheet in the vicinity of an X line can give a current in the direction appropriate for E x J is less than 0. The way in which the balance between gyroviscosity and the electric force along an X line is maintained for any E x J is shown. It is concluded that observational evidence for the occasional existence of E x J is less than 0 along an X line provides support for the suggestion that collisionless graviscosity, rather than resistivity, balances the electric force along an X line. It is found that there is a maximum electric field magnitude for particles to be able to carry a significant current. For parameters typical of the distant magnetotail, the critical electric field magnitude was found to be about 0.15 mV/m, which is of the order of, though somewhat less than, the potential electric field magnitudes expected in the magnetotail. This maximum allowable field magnitude is about the same for protons as it is for electrons in the magnetotail.

  16. The Barriers and Facilitators to Transfer of Ultrasound-Guided Central Venous Line Skills From Simulation to Practice: Exploring Perceptions of Learners and Supervisors.

    Science.gov (United States)

    Mema, Briseida; Harris, Ilene

    2016-01-01

    PHENOMENON: Ultrasound-guided central venous line insertion is currently the standard of care. Randomized controlled trials and systematic reviews show that simulation is superior to apprenticeship training. The purpose of this study is to explore, from the perspectives of participants in a simulation-training program, the factors that help or hinder the transfer of skills from simulation to practice. Purposeful sampling was used to select and study the experience and perspective of novice fellows after they had completed simulation training and then performed ultrasound-guided central venous line in practice. Seven novice pediatric intensive care unit fellows and six supervising faculty in a university-affiliated academic center in a large urban city were recruited between September 2012 and January 2013. We conducted a qualitative study using semistructured interviews as our data source, employing a constructivist, grounded theory methodology. Both curricular and real-life factors influence the transfer of skills from simulation to practice and the overall performance of trainees. Clear instructions, the opportunity to practice to mastery, one-on-one observation with feedback, supervision, and further real-life experiences were perceived as factors that facilitated the transfer of skills. Concern for patient welfare, live trouble shooting, complexity of the intensive care unit environment, and the procedure itself were perceived as real-life factors that hindered the transfer of skills. Insights: As more studies confirm the superiority of simulation training versus apprenticeship training for initial student learning, the faculty should gain insight into factors that facilitate and hinder the transfer of skills from simulation to bedside settings and impact learners' performances. As simulation further augments clinical learning, efforts should be made to modify the curricular and bedside factors that facilitate transfer of skills from simulation to practice

  17. Assessment of noise and heavy metals (Cr, Cu, Cd, Pb) in the ambience of the production line for recycling waste printed circuit boards.

    Science.gov (United States)

    Xue, Mianqiang; Yang, Yichen; Ruan, Jujun; Xu, Zhenming

    2012-01-03

    The crush-pneumatic separation-corona electrostatic separation production line provides a feasible method for industrialization of waste printed circuit boards (PCBs) recycling. To determine the potential environmental contamination in the automatic line workshop, noise and heavy metals (Cr, Cu, Cd, Pb) in the ambience of the production line have been evaluated in this paper. The mean noise level in the workshop has been reduced from 96.4 to 79.3 dB since the engineering noise control measures were employed. Noise whose frequency ranged from 500 to 1000 Hz is controlled effectively. The mass concentrations of TSP and PM(10) in the workshop are 282.6 and 202.0 μg/m(3), respectively. Pb (1.40 μg/m(3)) and Cu (1.22 μg/m(3)) are the most enriched metals in TSP samples followed by Cr (0.17 μg/m(3)) and Cd (0.028 μg/m(3)). The concentrations of Cu, Pb, Cr, and Cd in PM(10) are 0.88, 0.56, 0.12, and 0.88 μg/m(3), respectively. Among the four metals, Cr and Pb are released into the ambience of the automatic line more easily in the crush and separation process. Health risk assessment shows that noncancerous effects might be possible for Pb (HI = 1.45), and noncancerous effects are unlikely for Cr, Cu, and Cd. The carcinogenic risks for Cr and Cd are 3.29 × 10(-8) and 1.61 × 10(-9), respectively. It indicates that carcinogenic risks on workers are relatively light in the workshop. These findings suggest that this technology is advanced from the perspective of environmental protection in the waste PCBs recycling industry.

  18. Element interactions and soil properties affecting the soil-to-plant transfer of six elements relevant to radioactive waste in boreal forest

    Energy Technology Data Exchange (ETDEWEB)

    Roivainen, Paeivi; Makkonen, Sari; Holopainen, Toini; Juutilainen, Jukka [University of Eastern Finland, Department of Environmental Science, Kuopio (Finland)

    2012-03-15

    Cobalt (Co), lead (Pb), molybdenum (Mo), nickel (Ni), uranium (U), and zinc (Zn) are among the elements that have radioactive isotopes in radioactive waste. Soil-to-plant transfer is a key process for possible adverse effects if these radionuclides are accidentally released into the environment. The present study aimed at investigating factors affecting such transfer in boreal forest. The plant species studied were blueberry (Vaccinium myrtillus), May lily (Maianthemum bifolium), narrow buckler fern (Dryopteris carthusiana), rowan (Sorbus aucuparia) and Norway spruce (Picea abies). Regression analyses were carried out to investigate the effects of the chemical composition and physical properties of soil on the soil-to-leaf/needle concentration ratios of Co, Mo, Ni, Pb, U and Zn. Soil potassium (K), magnesium (Mg), manganese (Mn), phosphorus (P) and sulphur (S) concentrations were the most important factors affecting the soil-to-plant transfer of the elements studied. Soil clay and organic matter contents were found to significantly affect plant uptake of Mo, Pb and U. Knowledge of the effects of these factors is helpful for interpretation of the predictions of radioecological models describing soil-to-plant transfer and for improving such models. (orig.)

  19. Cryogenic electrical insulation of superconducting power transmission lines: transfer of experience learned from metal superconductors to high critical temperature superconductors

    Energy Technology Data Exchange (ETDEWEB)

    Gerhold, J. [Technical University of Graz (Austria). Inst. fuer Electrische Maschinen und Antrisbechnik; Tanaka, T. [Central Research Institute of Electric Power Industry, Tokyo (Japan)

    1998-11-01

    Superconducting power transmission lines have found renewed interest after the discovery of a superconductor with high critical temperature. Cooling by liquid nitrogen instead of helium has in fact a great impact on economics. The existing wide spread knowhow about dielectric performance in helium cooled transmission lines which were already developed up to a prototype stage can be used with benefit for the design of liquid nitrogen cooled lines. (author)

  20. Soil-to-plant transfer of elements is not linear: Results for five elements relevant to radioactive waste in five boreal forest species

    Energy Technology Data Exchange (ETDEWEB)

    Tuovinen, Tiina S.; Roivainen, Paeivi, E-mail: paivi.roivainen@uef.fi; Makkonen, Sari; Kolehmainen, Mikko; Holopainen, Toini; Juutilainen, Jukka

    2011-12-01

    Element-specific concentration ratios (CRs) assuming that plant uptake of elements is linear are commonly used in radioecological modelling to describe the soil-to-plant transfer of elements. The goal of this study was to investigate the validity of the linearity assumption in boreal forest plants, for which only limited relevant data are available. The soil-to-plant transfer of three essential (Mo, Ni, Zn) and two non-essential (Pb, U) elements relevant to the safety of radioactive waste disposal was studied. Three understory species (blueberry, narrow buckler fern and May lily) and two tree species (Norway spruce and rowan) were included. Examining CRs as a function of soil concentration showed that CR was not constant but decreased with increasing soil concentrations for all elements and plant species. A non-linear equation fitted fairly well with the empirical data; the R{sup 2}-values for this equation were constantly higher than those for the linear fit. The difference between the two fits was most evident at low soil concentrations where the use of constant CRs underestimated transfer from soil to plants. Site-specific factors affected the transfer of Mo and Ni. The results suggested that systematic variation with soil concentrations explains a part of the large variation of empirically determined CRs, and the accuracy of modelling the soil-to-plant transfer might be improved by using non-linear methods. Non-linearity of soil-to-plant transfer has been previously reported for a few different species, elements and environments. The present study systematically tested the linearity assumption for five elements (both essential and non-essential) and in five boreal forest species representing different growth traits and phylogenies. The data supported non-linearity in all cases.

  1. Analysis of the effects of explosion of a hydrogen cylinder on the transfer of radioactive liquid wastes at nuclear power stations

    Energy Technology Data Exchange (ETDEWEB)

    Lopes, Karina B., E-mail: karina@inb.gov.b [Industrias Nucleares do Brasil (INB), Rio de Janeiro, RJ (Brazil); Melo, Paulo Fernando F.F. e, E-mail: frutoso@nuclear.ufrj.b [Universidade Federal do Rio de Janeiro (PEN/COPPE/UFRJ), RJ (Brazil). Coordenacao dos Programas de Pos-Graduacao de Engenharia. Programa de Engenharia Nuclear

    2011-07-01

    This work presents a study of explosion effects of a stored hydrogen cylinder on the transfer of radioactive liquid wastes at nuclear power plants. The peak overpressure is calculated, as well as the strength of resulting fragments, thus confirming the main harmful effect of an explosion of flammable vapor cloud, based on the TNT equivalent method. The scenarios identified are calculated and compared with the overpressure ranges of 1%, 50% and 99% of structural damages, which were determined by the Eisenberg's vulnerability model. The results show that the overpressure and the resulting fragments from the explosion of a hydrogen gas cylinder are not able to cause the overturning of the tanker under study, and also show that a minimum distance of 30 meters between the hydrogen cylinder and the tanker can be considered a safe distance to the passage of this tanker during the transfer of radioactive liquid waste, in which the likelihood of occurrence of structural damages is less than 1%. (author)

  2. The potential environmental gains from recycling waste plastics: simulation of transferring recycling and recovery technologies to Shenyang, China.

    Science.gov (United States)

    Chen, Xudong; Xi, Fengming; Geng, Yong; Fujita, Tsuyoshi

    2011-01-01

    With the increasing attention on developing a low-carbon economy, it is necessary to seek appropriate ways on reducing greenhouse gas (GHG) emissions through innovative municipal solid waste management (MSWM), such as urban symbiosis. However, quantitative assessments on the environmental benefits of urban symbiosis, especially in developing countries, are limited because only a limited number of planned synergistic activities have been successful and it is difficult to acquire detailed inventory data from private companies. This paper modifies and applies a two-step simulation system and used it to assess the potential environmental benefits, including the reduction of GHG emissions and saving of fossil fuels, by employing various Japanese plastics recycling/energy-recovery technologies in Shenyang, China. The results showed that among various recycling/energy-recovery technologies, the mechanical waste plastics recycling technology, which produces concrete formwork boards (NF boards), has the greatest potential in terms of reducing GHG emissions (1.66 kg CO(2)e/kg plastics), whereas the technology for the production of refuse plastic fuel (RPF) has the greatest potential on saving fossil fuel consumption (0.77 kg ce/kg-plastics). Additional benefits can be gained by applying combined technologies that cascade the utilization of waste plastics. Moreover, the development of clean energy in conjunction with the promotion of new waste plastics recycling programs could contribute to additional reductions in GHG emissions and fossil fuel consumption. Copyright © 2010 Elsevier Ltd. All rights reserved.

  3. Waste Preparation and Transport Chemistry: Results of the FY 2002 Studies

    Energy Technology Data Exchange (ETDEWEB)

    Hunt, R.D.

    2003-07-10

    The initial step in the remediation of nuclear waste stored at Hanford and the Savannah River Site (SRS) involves the retrieval and transfer of the waste to another tank or to a treatment facility. The retrieved waste can range from a filtered supernatant to a slurry. Nearly all of the recent solid formation problems encountered during waste transfers and subsequent treatment steps have involved decanted or filtered supernatants. Problems with slurry transfers have not yet surfaced, because tank farm operations at Hanford and the SRS have focused primarily on supernatant transfers and treatment. For example, the interim stabilization program at Hanford continues to reduce the level of supernatants and interstitial liquids in its single-shell tanks through saltwell pumping of filtered liquid. In addition, at present, the cross-site transfer lines at Hanford can be used only to transfer liquids. Another reason for fewer problems with slurry transfers involves the additions of large quantities of dilution water prior to the transfer. When the waste is transferred, a drop in temperature is expected because most transfer lines are not heated. However, the dilution water reduces or eliminates solid formation caused by this temperature drop. In sharp contrast, decanted or filtered supernatants are near or at saturation for certain compounds. In such cases, tank farm operators must continue to evaporate their liquid waste since available tank space is quite limited. Solid formation can occur when the temperature of saturated solutions drops even slightly. The evaporation step can also lead to the formation of problematic solids. At the SRS, the evaporation of a relatively dilute waste stream was suspended due to the formation of deposits in the evaporator system. Therefore, small drops in temperature or evaporation can lead to problematic solid formations.

  4. Green way genesis of silver nanoparticles using multiple fruit peels waste and its antimicrobial, anti-oxidant and anti-tumor cell line studies

    Science.gov (United States)

    Naganathan, Kiruthika; Thirunavukkarasu, Somanathan

    2017-04-01

    Green synthesis of silver nanoparticles (SNP) opens a new path to kill and prevent various infectious diseases and also tumor. In this study, we have synthesized silver nanoparticles using multiple fruit peel waste (pomegranate, orange, banana and apple (POBA)). The primarily nanoparticles formation has been confirmed by the color change. The synthesized SNP were analyzed by various physicochemical techniques such as UV- Visible spectroscopy, x-ray diffraction (XRD), fourier transform infra red (FT-IR) spectroscopy and transmission electron microscope (TEM). The formation of SNP was confirmed by its absorbance peak observed at 430 nm in UV-Visible spectrum. Further, the obtained SNP were identified by XRD and TEM, respectively to know the crystalline nature and size and shape of the particles. The activities of SNP were checked with human pathogens (Salmonella, E.coli and Pseudomonas), plant pathogen (Fusarium) and marine pathogen (Aeromonas hydrophila) and also studied the scavenging effect and anticancer properties against MCF-7 cell lines. This studies proves that the SNP prepared from fruit waste peel extract approach appears extremely fast, cost efficient, eco-friendly and alternative for conventional methods of SNP synthesis to promote the usage of these nanoparticles in medicinal application.

  5. Analysis of interactions of mechanical deformations and mass transfer on heat transfer from an underground nuclear-waste repository. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Bloom, S.G.; Hulbert, L.E.

    1979-10-01

    A review of existing models identified several effects that may need consideration in further model development. Most of these effects involved coupling equations through variable property values rather than through omission of any significant mechanism. However, it was also shown that more than one mechanism may adequately simulate a given set of experimental data and additional experimental data are needed to establish which (if any) of the possible mechanisms would actually control conditions in a nuclear waste repository. In particular, it is believed that mathematical modeling of major thermomechanical effects can be accomplished with finite element analysis computer programs, provided that adequate thermomechanical property data of salt and overburden are attained. An attempt was made to develop a general set of differential equations for simulating momentum, mass, and energy flows in geologic formations in order to illustrate the possible mechanisms and point out those included and not included in existing models. Most of the mechanisms are included in some manner in existing models although some approximations may not be adequate. More experimental data are required to assess the importance of most omitted mechanisms. Analysis of some data on brine migration in salt indicated that two mechanisms, acting simultaneously, could adequately explain the flow. These are Darcy flow and a combination of ordinary and thermal diffusion enhanced by temperature-dependent solubility. Equations based on this simultaneous action correlated the data very well and indicated the possible need to include both (and, maybe other) mechanisms in future models. A program is recommended for further study of brine mobility. An expected result of this program includes recommendations for further experimental work.

  6. Heat and mass transfer through spiral tubes in absorber of absorption heat pump system for waste heat recovery

    Directory of Open Access Journals (Sweden)

    Yoshinori Itaya

    2017-06-01

    Full Text Available Heat and mass transfer of a LiBr/water absorption heat pump system (AHP was experimentally studied during working a heating-up mode. The examination was performed for a single spiral tube, which was simulated for heat transfer tubes in an absorber. The inside and outside of the tube were subjected to a film flow of the absorption liquid and exposed to the atmosphere, respectively. The maximum temperature of the absorption liquid was observed not at the entrance but in the region a little downward from the entrance in the tube. The steam absorption rate and/or heat generation rate in the liquid film are not constant along the tube. Hence the average convective heat transfer coefficient between the liquid film flowing down and the inside wall of the tube was determined based on a logarithmic mean temperature difference between the tube surface temperature and the film temperature at the maximum temperature location and the bottom. The film heat and mass transfer coefficients rose with increasing Reynolds number of the liquid film stream. The coefficients showed opposite trend to the empirical correlation reported for laminar film flow on a straight smooth tube in a refrigeration mode in the past work. The fact can be caused due to a turbulent promotion effect of the liquid in a spiral tube.

  7. The distribution and sea-air transfer of volatile mercury in waste post-desulfurization seawater discharged from a coal-fired power plant.

    Science.gov (United States)

    Sun, Lumin; Lin, Shanshan; Feng, Lifeng; Huang, Shuyuan; Yuan, Dongxing

    2013-09-01

    The waste seawater discharged in coastal areas from coal-fired power plants equipped with a seawater desulfurization system might carry pollutants such as mercury from the flue gas into the adjacent seas. However, only very limited impact studies have been carried out. Taking a typical plant in Xiamen as an example, the present study targeted the distribution and sea-air transfer flux of volatile mercury in seawater, in order to trace the fate of the discharged mercury other than into the sediments. Samples from 28 sampling sites were collected in the sea area around two discharge outlets of the plant, daily and seasonally. Total mercury, dissolved gaseous mercury and dissolved total mercury in the seawater, as well as gaseous elemental mercury above the sea surface, were investigated. Mean concentrations of dissolved gaseous mercury and gaseous elemental mercury in the area were 183 and 4.48 ng m(-3) in summer and 116 and 3.92 ng m(-3) in winter, which were significantly higher than those at a reference site. Based on the flux calculation, the transfer of volatile mercury was from the sea surface into the atmosphere, and more than 4.4 kg mercury, accounting for at least 2.2 % of the total discharge amount of the coal-fired power plant in the sampling area (1 km(2)), was emitted to the air annually. This study strongly suggested that besides being deposited into the sediment and diluted with seawater, emission into the atmosphere was an important fate for the mercury from the waste seawater from coal-fired power plants.

  8. Development of a high-titer retrovirus producer cell line capable of gene transfer into rhesus monkey hematopoietic stem cells

    Energy Technology Data Exchange (ETDEWEB)

    Bodine, D.M.; McDonagh, K.T.; Brandt, S.J.; Ney, P.A.; Agricola, B.; Byrne, E.; Nienhuis, A.W. (National Institutes of Health, Bethesda, MD (USA))

    1990-05-01

    Retroviral-mediated gene transfer into primitive hematopoietic cells has been difficult to achieve in large-animal models. The authors have developed an amphotropic producer clone that generates >10{sup 10} recombinant retroviral particles (colony-forming units) per ml of culture medium. Autologous rhesus monkey bone marrow cells were cocultured with either high or low titer producer clones for 4-6 days and reinfused into sublethally irradiated animals. The proviral genome was detected in blood and bone-marrow cells from all three animals reconstituted with cells cocultured with the high-titer producer cells. In contrast, three animals reconstituted with bone marrow cocultured with the low-titer producer clone exhibited no evidence of gene transfer.

  9. Short Wave upwelling Radiative Flux (SWupRF) within NIR range for the selected greenhouse wavelength bands of O2, H2O, CO2 and CH4 by Argus 1000 along with GENSPECT line by line radiative transfer model

    CERN Document Server

    Siddiqui, Rehan; Salem, Naif Al; Quine, Brendan M

    2016-01-01

    This new study develops an algorithm for Short Wave upwelling Radiative Flux (SWupRF) for the spectral variations within near infrared (NIR) from 1100 to 1700 nm wavelength band based on remote sensing data set of Argus 1000 micro-spectrometer observations. We calculate the SWupRF by investigating the total radiative flux due to O2, H2O, CO2 and CH4 and also by the individual gas within the selected wavelength bands of interest. A GENSPECT synthetic line by line radiative transfer model is applied to perform radiative transfer simulations to calculate the radiative flux by varying surface albedo, mixing ratios of the selected greenhouse gases, surface temperature, solar sun and zenith angles with different latitude and longitude of the instrument. Finally, the SWupRFsyn estimated from GENSPECT was compared with SWupRFobs from Argus 1000 over a period of four years (2009 and 2013) covering all seasons. We calculate and compare both the synthetic and real measured observed data set. The synthetic model gives SW...

  10. Analysis of the time series of waste water quality at the inflow of the wastewater treatment plant and transfer functions

    Directory of Open Access Journals (Sweden)

    Nesmerak Ivan

    2014-03-01

    Full Text Available Time series of the daily total precipitation, daily wastewater discharges and daily concentrations and pollution loads of BOD5, COD, SS, N-NH4, Ntot and Ptot were analyzed at the inflow to the wastewater treatment plant (WWTP for a larger city in 2004-2009 (WWTP is loaded by pollution from 435,000 equivalent inhabitants. The time series of the outflow from a WWTP was also available for 2007. The time series of daily total precipitation, daily wastewater discharges, concentrations and pollution loads at the inflow and outflow from the WWTP were standardized year by year to exclude a long-term trend, and periodic components with a period of 7 days and 365 days (and potentially also 186.5 days were excluded from the standardized series. However, these two operations eliminated only a small part of the variance; there was a substantial reduction in the variance only for ammonium nitrogen and total nitrogen at the inflow and outflow from a WWTP. The relationship between the inflow into a WWTP and the outflow from a WWTP for the concentrations and pollution loads was described by simple transfer functions (SISO models and more complicated transfer functions (MISO models. A simple transfer function (SISO model was employed to describe the relationship between the daily total precipitation and the wastewater discharge.

  11. Oral and vaginal epithelial cell lines bind and transfer cell-free infectious HIV-1 to permissive cells but are not productively infected.

    Directory of Open Access Journals (Sweden)

    Arinder Kohli

    Full Text Available The majority of HIV-1 infections worldwide are acquired via mucosal surfaces. However, unlike the vaginal mucosa, the issue of whether the oral mucosa can act as a portal of entry for HIV-1 infection remains controversial. To address potential differences with regard to the fate of HIV-1 after exposure to oral and vaginal epithelium, we utilized two epithelial cell lines representative of buccal (TR146 and pharyngeal (FaDu sites of the oral cavity and compared them with a cell line derived from vaginal epithelium (A431 in order to determine (i HIV-1 receptor gene and protein expression, (ii whether HIV-1 genome integration into epithelial cells occurs, (iii whether productive viral infection ensues, and (iv whether infectious virus can be transferred to permissive cells. Using flow cytometry to measure captured virus by HIV-1 gp120 protein detection and western blot to detect HIV-1 p24 gag protein, we demonstrate that buccal, pharyngeal and vaginal epithelial cells capture CXCR4- and CCR5-utilising virus, probably via non-canonical receptors. Both oral and vaginal epithelial cells are able to transfer infectious virus to permissive cells either directly through cell-cell attachment or via transcytosis of HIV-1 across epithelial cells. However, HIV-1 integration, as measured by real-time PCR and presence of early gene mRNA transcripts and de novo protein production were not detected in either epithelial cell type. Importantly, both oral and vaginal epithelial cells were able to support integration and productive infection if HIV-1 entered via the endocytic pathway driven by VSV-G. Our data demonstrate that under normal conditions productive HIV-1 infection of epithelial cells leading to progeny virion production is unlikely, but that epithelial cells can act as mediators of systemic viral dissemination through attachment and transfer of HIV-1 to permissive cells.

  12. Potential transfer of neurotoxic amino acid β-N-methylamino-alanine (BMAA) from mother to infant during breast-feeding: Predictions from human cell lines.

    Science.gov (United States)

    Andersson, Marie; Ersson, Lisa; Brandt, Ingvar; Bergström, Ulrika

    2017-04-01

    β-N-methylamino-alanine (BMAA) is a non-protein amino acid produced by cyanobacteria, diatoms and dinoflagellates. BMAA has potential to biomagnify in a terrestrial food chain, and to bioaccumulate in fish and shellfish. We have reported that administration of [14C]l-BMAA to lactating mice and rats results in a mother to off-spring transfer via the milk. A preferential enantiomer-specific uptake of [14C]l-BMAA has also been demonstrated in differentiated murine mammary epithelium HC11 cells. These findings, together with neurotoxic effects of BMAA demonstrated both in vitro and in vivo, highlight the need to determine whether such transfer could also occur in humans. Here, we used four cell lines of human origin to examine and compare the transport of the two BMAA enantiomers in vitro. The uptake patterns of [14C]l- and [14C]d-BMAA in the human mammary MCF7 cell line were in agreement with the results in murine HC11 cells, suggesting a potential secretion of BMAA into human breast milk. The permeability coefficients for both [14C]l- and [14C]d-BMAA over monolayers of human intestinal Caco2 cells supported an efficient absorption from the human intestine. As a final step, transport experiments confirmed that [14C]l-and [14C]d-BMAA can be taken up by human SHSY5Y neuroblastoma cells and even more efficiently by human U343 glioblastoma cells. In competition experiments with various amino acids, the ASCT2 specific inhibitor benzylserine was the most effective inhibitor of [14C]l-BMAA uptake tested here. Altogether, our results suggest that BMAA can be transferred from an exposed mother, via the milk, to the brain of the nursed infant. Copyright © 2017. Published by Elsevier Inc.

  13. Nuclear donor cell lines considerably influence cloning efficiency and the incidence of large offspring syndrome in bovine somatic cell nuclear transfer.

    Science.gov (United States)

    Liu, J; Wang, Y; Su, J; Luo, Y; Quan, F; Zhang, Y

    2013-08-01

    Total five ear skin fibroblast lines (named F1, F2, F3, F4 and F5) from different newborn Holstein cows have been used as nuclear donor cells for producing cloned cows by somatic cell nuclear transfer (SCNT). The effects of these cell lines on both in vitro and in vivo developmental rates of cloned embryos, post-natal survivability and incidence of large offspring syndrome (LOS) were examined in this study. We found that the different cell lines possessed the same capacity to support pre-implantation development of cloned embryos, the cleavage and blastocyst formation rates ranged from 80.2 ± 0.9 to 84.5 ± 2.5% and 28.5 ± 0.9 to 33.3 ± 1.4%, respectively. However, their capacities to support the in vivo development of SCNT embryos showed significant differences (p cloning efficiency was significantly higher in group F5 than those in group F1, F2, F3 and F4 (9.3% vs 4.1%, 1.2%, 2.0% and 5.0%, respectively, p cloned offspring from cell line F1, F2, F3 and F4 showed LOS and gestation length delay, while all cloned offspring from F5 showed normal birthweight and gestation length. We concluded that the nuclear donor cell lines have significant impact on the in vivo development of cloned embryos and the incidence of LOS in cloned calves. © 2013 Blackwell Verlag GmbH.

  14. Effect of superheat, mold, and casting materials on the metal/mold interfacial heat transfer during solidification in graphite-lined permanent molds

    Science.gov (United States)

    Prabhu, K. Narayan; Suresha, K. M.

    2004-10-01

    Heat transfer during the solidification of an Al-Cu-Si alloy (LM4) and commercial pure tin in single steel, graphite, and graphite-lined metallic (composite) molds was investigated. Experiments were carried out at three different superheats. In the case of composite molds, the effect of the thickness of the graphite lining and the outer wall on heat transfer was studied. Temperatures at known locations inside the mold and casting were used to solve the Fourier heat conduction equation inversely to yield the casting/mold interfacial heat flux transients. Increased melt superheats and higher thermal conductivity of the mold material led to an increase in the peak heat flux at the metal/mold interface. Factorial experiments indicated that the mold material had a significant effect on the peak heat flux at the 5% level of significance. The ratio of graphite lining to outer steel wall and superheat had a significant effect on the peak heat flux in significance range varying between 5 and 25%. A heat flux model was proposed to estimate the maximum heat flux transients at different superheat levels of 25 to 75 °C for any metal/mold combinations having a thermal diffusivity ratio (α R) varying between 0.25 and 6.96. The heat flow models could be used to estimate interfacial heat flux transients from the thermophysical properties of the mold and cast materials and the melt superheat. Metallographic analysis indicated finer microstructures for castings poured at increased melt superheats and cast in high-thermal diffusivity molds.

  15. Asymmetrical flow field-flow fractionation with on-line detection for drug transfer studies: a feasibility study

    DEFF Research Database (Denmark)

    Hinna, A.; Steiniger, F.; Hupfeld, S.

    2014-01-01

    Knowledge about drug retention within colloidal carriers is of uppermost importance particularly if drug targeting is anticipated. The aim of the present study was to evaluate asymmetrical flow field-flow fractionation (AF4) with on-line UV/VIS drug quantification for its suitability to determine...... was found repeatable and robust. The employed combination of AF4 with multi-angle laser light scattering furthermore provided detailed size information of the eluting sample and thus allowed to detect instabilities and/or interactions between the donor and acceptor liposomes. Drug quantification by on...

  16. LIME - a flexible, non-LTE line excitation and radiation transfer method for millimeter and far-infrared wavelengths

    DEFF Research Database (Denmark)

    Brinch, Christian; Hogerheijde, Michiel

    2010-01-01

    can be used as input, ranging from analytical descriptions over tabulated models to SPH simulations. To generate the Delaunay grid we sample the input model randomly, but weigh the sample probability with the molecular density and other parameters, and thereby we obtain an average grid point...... that can readily be compared to observations. Because of the high dynamic range in scales that can be resolved using this type of grid, our code is particularly well suited for modeling of ALMA data. Our code can furthermore deal with overlapping lines of multiple molecular and atomic species....

  17. Nuclear waste storage container with metal matrix

    Science.gov (United States)

    Sump, Kenneth R.

    1978-01-01

    The invention relates to a storage container for high-level waste having a metal matrix for the high-level waste, thereby providing greater impact strength for the waste container and increasing heat transfer properties.

  18. The effect of direction for hydrophobic lines on subcooled flow boiling: Critical heat flux and heat transfer coefficient

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Jin Man; Yu, Dong In; Park, Hyun Sun; Kim, Moo Hwan [POSTECH, Pohang (Korea, Republic of)

    2015-10-15

    A lot of time and effort were dedicated on study of BHT and CHF to understand and control boiling characteristics. To enhance boiling performance, structure and coating have been focused on recently. Coating can change wettability of the surface by controlling surface energy. Structure can affect nucleation cavity or wettability. These techniques make differences for boiling phenomena. From many reports, structures have received much attention due to facileness of manipulation for wetting, and so much data were collected about structures and boiling characteristics. In comparison to the structure, the study of coating technique is less active. Hydrophilic surface without structure is difficult to make for lasting during boiling condition, and hydrophobic surface impoverish CHF due to early dryout. For this reason, the study of coating effect is deficient relatively. However, hydrophobic pattern can be a brilliant method to enhance boiling performance. Betz et al. manufactured superbiphilic surfaces having juxtaposing hexagonal hydrophobic dots on the superhydrophilic surface. This surface improved HTC up to three times higher than on reported nanostructured surfaces. They reported that results were from increasing nucleation site due to hydrophobicity and constraining of bubble expansion on the surface to prevent formation of vapor blanket. In this study, hydrophobic patterns with stripe lines were achieved to study direction effect of hydrophobic pattern using Teflon solution, and further research is suggested. From the analysis of bubble dynamics with pattern effects, the following conclusions can be summarized. 1. Teflon coating can make many bubbles at early stage, so it showed the highest HTC, but lowest CHF due to early formation of vapor blanket. 2. Parallel patterns are advantageous higher CHF due to segregated vapor path in flow direction. 3. Cross patterns are unfavorable to delay CHF because merged vapor jets could cover hydrophilic line.

  19. Bioaccumulation of short chain chlorinated paraffins in a typical freshwater food web contaminated by e-waste in south china: Bioaccumulation factors, tissue distribution, and trophic transfer.

    Science.gov (United States)

    Sun, Runxia; Luo, Xiaojun; Tang, Bin; Chen, Laiguo; Liu, Yu; Mai, Bixian

    2017-03-01

    Short chain chlorinated paraffins (SCCPs) are under review for inclusion into the Stockholm Convention on Persistent Organic Pollutants. However, limited information is available on their bioaccumulation and biomagnification in ecosystems, which is hindering evaluation of their ecological and health risks. In the present study, wild aquatic organisms (fish and invertebrates), water, and sediment collected from an enclosed freshwater pond contaminated by electronic waste (e-waste) were analyzed to investigate the bioaccumulation, distribution, and trophic transfer of SCCPs in the aquatic ecosystem. SCCPs were detected in all of the investigated aquatic species at concentrations of 1700-95,000 ng/g lipid weight. The calculated bioaccumulation factors (BAFs) varied from 2.46 to 3.49. The relationship between log BAF and the octanol/water partition coefficient (log K OW ) for benthopelagic omnivorous fish species followed the empirical model of bioconcentration, indicating that bioconcentration plays an important role in accumulation of SCCPs. In contrast, the relationship for the benthic carnivorous fish and invertebrates was not consistent with the empirical model of bioconcentration, implying that the bioaccumulation of SCCPs in these species could be more influenced by other complex factors (e.g., habitat and feeding habit). Preferential distribution in the liver rather than in other tissues (e.g., muscle, gills, skin, and kidneys) was noted for the SCCP congeners with higher log K OW , and bioaccumulation pathway (i.e. water or sediment) can affect the tissue distribution of SCCP congeners. SCCPs underwent trophic dilution in the aquatic food web, and the trophic magnification factor (TMF) values of SCCP congener groups significantly correlated with their corresponding log K OW values (p < 0.0001). The present study results improved our understanding on the environmental behavior and fate of SCCPs in aquatic ecosystem. Copyright © 2016 Elsevier Ltd. All rights

  20. Determination of pipemidic acid based on flow-injection chemiluminescence due to energy transfer from peroxynitrous acid synthesized on-line.

    Science.gov (United States)

    Liang, Yao-Dong; Song, Jun-Feng; Tian, Tian

    2004-12-01

    A flow-injection chemiluminescence (CL) method for the determination of pipemidic acid is described. It is based on energy transfer from excited state peroxynitrous acid to pipemidic acid, in which the excited state peroxynitrous acid is synthesized on-line by the mixing of acid hydrogen peroxide with nitrite in a flow system and the CL is from two excited states of pipemidic acid. The proposed method allows the measurement of pipemidic acid over the range of 2.0 x 10(-7)-2.0 x 10(-5) mol l(-1) . The detection limit is 6.3 x 10(-8) mol l(-1), and the relative standard deviation for 2.0 x 10(-6) mol l(-1) pipemidic acid (n = 9) is 0.9%. This method was evaluated by the analysis of pipemidic acid in pharmaceutical preparations.

  1. Subbarrier heavy ion fusion enhanced by nucleon transfer and subbarrier fusion of nuclei far from the line of {beta}-stability

    Energy Technology Data Exchange (ETDEWEB)

    Denisov, V.Yu. [Institute for Nuclear Research, Kiev (Ukraine)]|[Gesellschaft fuer Schwerionenforschung mbH, Darmstadt (Germany)

    1998-09-01

    We discuss a model for the description of subbarrier fusion of heavy ions which takes into account the coupling to the low-energy surface vibrational states and to the few-nucleon transfer with arbitrary reaction Q-value. The fusion reactions {sup 28,30}Si+{sup 58,62,64}Ni, {sup 40}Ca+{sup 90,96}Zr, {sup 28}S+{sup 94,100}Mo, {sup 16,18,20,22,24}O+{sup 58}Ni and {sup 28}Si+{sup 124,126,128,130,132}Sn are analyzed in detail. The model describes rather well the experimental fusion cross section and mean angular momentum for reactions between nuclei near the {beta}-stability line. It is shown that these quantities are significantly enhanced by few-nucleon transfer with large positive Q-value. A shape independent parameterization of the heavy ion potential at distances smaller then the touching point is proposed. (orig.)

  2. Safety-relevant hydrogeological properties of the claystone barrier of a Swiss radioactive waste repository: An evaluation using multiple lines of evidence

    Science.gov (United States)

    Gautschi, Andreas

    2017-09-01

    In Switzerland, the Opalinus Clay - a Jurassic (Aalenian) claystone formation - has been proposed as the first-priority host rock for a deep geological repository for both low- and intermediate-level and high-level radioactive wastes. An extensive site and host rock investigation programme has been carried out during the past 30 years in Northern Switzerland, comprising extensive 2D and 3D seismic surveys, a series of deep boreholes within and around potential geological siting regions, experiments in the international Mont Terri Rock Laboratory, compilations of data from Opalinus Clay in railway and motorway tunnels and comparisons with similar rocks. The hydrogeological properties of the Opalinus Clay that are relevant from the viewpoint of long-term safety are described and illustrated. The main conclusions are supported by multiple lines of evidence, demonstrating consistency of conclusions based on hydraulic properties, porewater chemistry, distribution of natural tracers across the Opalinus Clay as well as small- and large-scale diffusion models and the derived conceptual understanding of solute transport.

  3. Monitoring of volatile compound emissions during dry anaerobic digestion of the Organic Fraction of Municipal Solid Waste by Proton Transfer Reaction Time-of-Flight Mass Spectrometry.

    Science.gov (United States)

    Papurello, Davide; Soukoulis, Christos; Schuhfried, Erna; Cappellin, Luca; Gasperi, Flavia; Silvestri, Silvia; Santarelli, Massimo; Biasioli, Franco

    2012-12-01

    Volatile Organic Compounds (VOCs) formed during anaerobic digestion of aerobically pre-treated Organic Fraction of Municipal Solid Waste (OFMSW), have been monitored over a 30 day period by a direct injection mass spectrometric technique: Proton Transfer Reaction Time-of-Flight Mass Spectrometry (PTR-ToF-MS). Most of the tentatively identified compounds exhibited a double-peaked emission pattern which is probably the combined result from the volatilization or oxidation of the biomass-inherited organic compounds and the microbial degradation of organic substrates. Of the sulfur compounds, hydrogen sulfide had the highest accumulative production. Alkylthiols were the predominant sulfur organic compounds, reaching their maximum levels during the last stage of the process. H(2)S formation seems to be influenced by the metabolic reactions that the sulfur organic compounds undergo, such as a methanogenesis induced mechanism i.e. an amino acid degradation/sulfate reduction. Comparison of different batches indicates that PTR-ToF-MS is a suitable tool providing information for rapid in situ bioprocess monitoring. Copyright © 2012 Elsevier Ltd. All rights reserved.

  4. Modeling municipal solid waste collection: A generalized vehicle routing model with multiple transfer stations, gather sites and inhomogeneous vehicles in time windows.

    Science.gov (United States)

    Son, Le Hoang; Louati, Amal

    2016-06-01

    Municipal Solid Waste (MSW) collection is a necessary process in any municipality resulting in the quality-of-life, economic aspects and urban structuralization. The intrinsic nature of MSW collection relates to the development of effective vehicle routing models that optimize the total traveling distances of vehicles, the environmental emission and the investment costs. In this article, we propose a generalized vehicle routing model including multiple transfer stations, gather sites and inhomogeneous vehicles in time windows for MSW collection. It takes into account traveling in one-way routes, the number of vehicles per m(2) and waiting time at traffic stops for reduction of operational time. The proposed model could be used for scenarios having similar node structures and vehicles' characteristics. A case study at Danang city, Vietnam is given to illustrate the applicability of this model. The experimental results have clearly shown that the new model reduces both total traveling distances and operational hours of vehicles in comparison with those of practical scenarios. Optimal routes of vehicles on streets and markets at Danang are given. Those results are significant to practitioners and local policy makers. Copyright © 2016 Elsevier Ltd. All rights reserved.

  5. Distribution of tetracycline resistance genes in anaerobic treatment of waste sludge: The role of pH in regulating tetracycline resistant bacteria and horizontal gene transfer.

    Science.gov (United States)

    Huang, Haining; Chen, Yinguang; Zheng, Xiong; Su, Yinglong; Wan, Rui; Yang, Shouye

    2016-10-01

    Although pH value has been widely regarded as an important factor that affects resource recovery of waste sludge, the potential influence of diverse pHs on the distribution of tetracycline resistance genes (TRGs) during sludge anaerobic treatment is largely unknown. Here we reported that in the range of pH 4-10, 0.58-1.18 log unit increase of target TRGs was observed at pH 4, compared with that at pH 7, while 0.70-1.31 log unit further removal were obtained at pH 10. Mechanism study revealed that varied pHs not only altered the community structures of tetracycline resistant bacteria (TRB), but also changed their relative abundances, benefitting the propagation (acidic pHs) or attenuation (alkaline pHs) of TRB. Further investigation indicated that the amount and gene-possessing abilities of key genetic vectors for horizontal TRGs transfer were greatly promoted at acidic pHs but restricted under alkaline conditions. Copyright © 2016 Elsevier Ltd. All rights reserved.

  6. The transesterification of rapeseed and waste sunflower oils: Mass-transfer and kinetics in a laboratory batch reactor and in an industrial-scale reactor/separator setup.

    Science.gov (United States)

    Klofutar, B; Golob, J; Likozar, B; Klofutar, C; Zagar, E; Poljansek, I

    2010-05-01

    We have investigated the transesterification of rapeseed (RO) and waste sunflower (SO) oils with methanol in the presence of potassium hydroxide as a catalyst. The transesterification of tri-acylglycerols was first conducted in a batch reactor. The effect of the temperature on the reaction rates was studied at a constant molar ratio of the alcohol to tri-acylglycerols (6:1) and for a constant concentration of the catalyst (1.0wt%). Size-exclusion chromatography and (1)H NMR spectroscopy were used to quantitatively monitor the transesterification reaction. The mass-transfer coefficients of the tri-acylglycerols during the initial transesterification stage were found to be 0.2-1.2x10(-5)mmin(-1), depending on the type of oil and the temperature. Calculated activation energies implied that at higher temperatures the formation of mono-acylglycerols and glycerole was favored for the SO (93kJ/mol for the forward and 48kJ/mol for the backward reaction) and the RO (47kJ/mol for the forward and 36kJ/mol for the backward reaction), respectively. For the continuous industrial reactor/separator setup, the optimum methanol recycle ratio was established as 0.0550. Copyright 2010 Elsevier Ltd. All rights reserved.

  7. Role of Extracellular Electron Transfer for Contaminant Metal Reduction in Sediment Nanopores, and Implications for Hazardous Waste Site Cleanup

    Science.gov (United States)

    Werth, C. J.; Michelson, K.; Valocchi, A. J.; Sanford, R. A.

    2016-12-01

    Microbial reduction of metals and radionuclides in the subsurface plays an essential role in the biogeochemical cycling of micronutrients and the remediation of contaminated sediments. While recent advances in the field have improved our ability to understand and predict bioreduction in these environments, the contribution of long-range extracellular electron transfer (EET) by electron shuttling or reduction along conductive pili remains elusive. Long-range EET is implicated in the reduction of radionuclides like uranium that are reversibly sorbed in clay nanopores and exist as persistant sources of contamination. In regions of low hydraulic conductivity, electron shuttles and conductive pili may increase physical mixing beyond what is possible by advection and diffusion, resulting in reduction over a larger area than predicted by current models. We present a novel microfluidic platform that allows us to study long-range EET to the exclusion of other mechanisms, directly observe these phenomena under a controlled environment representative of groundwater conditions, monitor the metabolic activity and redox state of bacteria, and determine the presence of reduced products in-situ. Using Geobacter sulfurreducens as a model metal-reducing bacteria, insoluble manganese dioxide as an electron acceptor, and Escherichia coli K-12 as a reductant and redox buffer, we demonstrate that 1) long-range EET by conductive pili requires the presence of flavins, 2) Reduction by direct contact within 200 nm wide pores only requires the presence of a lowered electric potential, 3) The limit of reduction by conductive pili is on the order of 15-20 microns. The results suggest that microbes can directly reduce metals via conductive pili in soil and sediment micropores as small as 200 nanometers in diameters, up to a depth of 20 microns. We are actively exploring the influence of hydrological conditions on the expression of different mechanisms of long-range EET, and the importance of

  8. Genome analysis of Elysia chlorotica Egg DNA provides no evidence for horizontal gene transfer into the germ line of this Kleptoplastic Mollusc.

    Science.gov (United States)

    Bhattacharya, Debashish; Pelletreau, Karen N; Price, Dana C; Sarver, Kara E; Rumpho, Mary E

    2013-08-01

    The sea slug Elysia chlorotica offers a unique opportunity to study the evolution of a novel function (photosynthesis) in a complex multicellular host. Elysia chlorotica harvests plastids (absent of nuclei) from its heterokont algal prey, Vaucheria litorea. The "stolen" plastids are maintained for several months in cells of the digestive tract and are essential for animal development. The basis of long-term maintenance of photosynthesis in this sea slug was thought to be explained by extensive horizontal gene transfer (HGT) from the nucleus of the alga to the animal nucleus, followed by expression of algal genes in the gut to provide essential plastid-destined proteins. Early studies of target genes and proteins supported the HGT hypothesis, but more recent genome-wide data provide conflicting results. Here, we generated significant genome data from the E. chlorotica germ line (egg DNA) and from V. litorea to test the HGT hypothesis. Our comprehensive analyses fail to provide evidence for alga-derived HGT into the germ line of the sea slug. Polymerase chain reaction analyses of genomic DNA and cDNA from different individual E. chlorotica suggest, however, that algal nuclear genes (or gene fragments) are present in the adult slug. We suggest that these nucleic acids may derive from and/or reside in extrachromosomal DNAs that are made available to the animal through contact with the alga. These data resolve a long-standing issue and suggest that HGT is not the primary reason underlying long-term maintenance of photosynthesis in E. chlorotica. Therefore, sea slug photosynthesis is sustained in as yet unexplained ways that do not appear to endanger the animal germ line through the introduction of dozens of foreign genes.

  9. Advancement in recombinant protein production using a marine oxygen carrier to enhance oxygen transfer in a CHO-S cell line.

    Science.gov (United States)

    Le Pape, Fiona; Bossard, Morgane; Dutheil, Delphine; Rousselot, Morgane; Polard, Valérie; Férec, Claude; Leize, Elisabeth; Delépine, Pascal; Zal, Franck

    2015-06-01

    Recombinant proteins, particularly proteins used as therapeutics, are widely expressed for bioprocessing manufacturing processes. Mammalian cell lines represent the major host cells for bioproduction, according to their capacities of post-translational modifications and folding of secreted proteins. Many parameters can affect cell productivity, especially the rate of oxygen transfer. Dissolved oxygen, in high or low proportions, is a crucial parameter which can affect cell viability and thus productivity. HEMARINA has developed a new technology, commercially proposed as HEMOXCell(®), to improve cell culture at a large production scale. HEMOXCell(®) is a marine oxygen carrier having properties of high oxygen sensitivity, to be used as an oxygen additive during cell culture manufacturing. In this study, we investigated the effects of HEMOXCell(®) on the culture of the commonly used CHO-S cell line. Two main objectives were pursued: 1) cell growth rate and viability during a batch mode process, and 2) the determination of the effect of this oxygen carrier on recombinant protein production from a CHO-transfected cell line. Our results show an increase of CHO-S cellular growth at a rate of more than four-fold in culture with HEMOXCell(®). Moreover, an extension of the growth exponential phase and high cell viability were observed. All of these benefits seem to contribute to the improvement of recombinant protein production. This work underlines several applications using this marine-type oxygen carrier for large biomanufacturing. It is a promising cell culture additive according to the increasing demand for therapeutic products such as monoclonal antibodies.

  10. Modelos de transferência de metal pesado na cana-de-açúcar adubada com composto de lixo urbano Heavy metal transference models in sugarcane fertilised with urban waste compost

    Directory of Open Access Journals (Sweden)

    Fábio C. da Silva

    2007-04-01

    Full Text Available A pesquisa aborda a reciclagem do composto de lixo urbano (CLU como fertilizante alternativo na cana-de-açúcar e como solução social e ambiental ao acúmulo de resíduos sólidos nos centros urbanos. Utilizou-se da modelagem matemática para conhecer a dinâmica dos metais pesados, visando ao estabelecimento de critérios e procedimentos para o uso seguro do CLU, limitado pela quantidade desses elementos. Foram construídos modelos compartimentais a partir de dados de experimentos em condições controladas e parcialmente validados com dados de campo. Esse modelo descreveu a transferência de metais pesados no sistema solo-raiz-parte aérea para a cana-de-açúcar. Pôde-se concluir, pelas condições desta pesquisa, que o metal mais preocupante foi o níquel, pois demora, aproximadamente, três anos para ser atenuado no solo e chega em maior quantidade na parte aérea. Quanto aos fatores argila, óxidos e pH do solo, notou-se que, nos solos de maior poder tampão, a passagem da maioria dos metais foi mais lenta. Esse modelo pode tornar-se importante aliado na definição de leis de utilização do CLU, visando à não-contaminação ambiental, redução no acúmulo de lixo e de custos de produção.The research approaches recycling of urban waste compost (UWC as an alternative fertilizer for sugarcane crop and as a social and environmental solution to the solids residuals growth in urban centers. A mathematical model was used in order to know the metal dynamics as decision support tool, aiming to establish of criteria and procedures for UWC's safe use, limited by the amount of heavy metal. A compartmental model was developed from experimental data in controlled conditions and partially checked with field data. This model described the heavy metal transference in the system soil-root-aerial portion of sugarcane plants and concluded that nickel was metal to be concern, since it takes approximately three years to be attenuated in the soil

  11. Activation of endogenous p53 by combined p19Arf gene transfer and nutlin-3 drug treatment modalities in the murine cell lines B16 and C6

    Directory of Open Access Journals (Sweden)

    Zanatta Daniela B

    2010-06-01

    Full Text Available Abstract Background Reactivation of p53 by either gene transfer or pharmacologic approaches may compensate for loss of p19Arf or excess mdm2 expression, common events in melanoma and glioma. In our previous work, we constructed the pCLPG retroviral vector where transgene expression is controlled by p53 through a p53-responsive promoter. The use of this vector to introduce p19Arf into tumor cells that harbor p53wt should yield viral expression of p19Arf which, in turn, would activate the endogenous p53 and result in enhanced vector expression and tumor suppression. Since nutlin-3 can activate p53 by blocking its interaction with mdm2, we explored the possibility that the combination of p19Arf gene transfer and nutlin-3 drug treatment may provide an additive benefit in stimulating p53 function. Methods B16 (mouse melanoma and C6 (rat glioma cell lines, which harbor p53wt, were transduced with pCLPGp19 and these were additionally treated with nutlin-3 or the DNA damaging agent, doxorubicin. Viral expression was confirmed by Western, Northern and immunofluorescence assays. p53 function was assessed by reporter gene activity provided by a p53-responsive construct. Alterations in proliferation and viability were measured by colony formation, growth curve, cell cycle and MTT assays. In an animal model, B16 cells were treated with the pCLPGp19 virus and/or drugs before subcutaneous injection in C57BL/6 mice, observation of tumor progression and histopathologic analyses. Results Here we show that the functional activation of endogenous p53wt in B16 was particularly challenging, but accomplished when combined gene transfer and drug treatments were applied, resulting in increased transactivation by p53, marked cell cycle alteration and reduced viability in culture. In an animal model, B16 cells treated with both p19Arf and nutlin-3 yielded increased necrosis and decreased BrdU marking. In comparison, C6 cells were quite susceptible to either treatment, yet

  12. Annual radioactive waste tank inspection program -- 1993

    Energy Technology Data Exchange (ETDEWEB)

    McNatt, F.G. Sr.

    1994-05-01

    Aqueous radioactive wastes from Savannah River Site (SRS) separations processes are contained in large underground carbon steel tanks. Inspections made during 1993 to evaluate these vessels, and evaluations based on data accrued by inspections made since the tanks were constructed, are the subject of this report. The 1993 inspection program revealed that the condition of the Savannah River Site waste tanks had not changed significantly from that reported in the previous annual report. No new leaksites were observed. No evidence of corrosion or materials degradation was observed in the waste tanks. However, degradation was observed on covers of the concrete encasements for the out-of-service transfer lines to Tanks 1 through 8.

  13. Operational Waste Volume Projection

    Energy Technology Data Exchange (ETDEWEB)

    STRODE, J.N.

    1999-08-24

    Waste receipts to the double-shell tank system are analyzed and wastes through the year 2018 are projected based on assumption as of July 1999. A computer simulation of site operations is performed, which results in projections of tank fill schedules, tank transfers, evaporator operations, tank retrieval, and aging waste tank usage. This projection incorporates current budget planning and the clean-up schedule of the Tri-Party Agreement.

  14. Operational waste volume projection

    Energy Technology Data Exchange (ETDEWEB)

    Koreski, G.M.

    1996-09-20

    Waste receipts to the double-shell tank system are analyzed and wastes through the year 2015 are projected based on generation trends of the past 12 months. A computer simulation of site operations is performed, which results in projections of tank fill schedules, tank transfers, evaporator operations, tank retrieval, and aging waste tank usage. This projection incorporates current budget planning and the clean-up schedule of the Tri-Party Agreement. Assumptions were current as of June 1996.

  15. A Primer on Transfer of Training.

    Science.gov (United States)

    Kelly, Helen Bryman

    1982-01-01

    Unless education transfers back to the job, training is wasted and its value questioned. This article examines resistance to transfer and provides strategies for building transfer into training design. (CT)

  16. Adenovirus-mediated gene transfer of glial cell line-derived neurotrophic factor prevents motor neuron loss of transgenic model mice for amyotrophic lateral sclerosis.

    Science.gov (United States)

    Manabe, Yasuhiro; Nagano, I; Gazi, M S A; Murakami, T; Shiote, M; Shoji, M; Kitagawa, H; Setoguchi, Y; Abe, K

    2002-08-01

    Effects of adenovirus-mediated gene transfer of glial cell line-derived neurotrophic factor (GDNF) were studied in transgenic (Tg) mice model for amyotrophic lateral sclerosis (ALS). Adenoviral vector containing GDNF gene (Ad-GDNF), E. coli lacZ (Ad-LacZ), or vehicle was injected once a week from 35 weeks of age into the right gastrocnemius muscle of Tg mice carrying mutant human Cu/Zn superoxide dismutase (SOD1) gene, and histological analysis was performed at 46 W. Clinical data showed a tendency of improvement, but was not significantly different among the three animal groups. In contrast, total number of and phospho-Akt (p-Akt) positive large motor neurons in the treated side was significantly preserved in Ad-GDNF-treated group than in vehicle- and Ad-LacZ-treated groups (*p < 0.05). Immunoreactivity of phospho-ERK (p-ERK) and active caspases-3 and -9 showed no difference. These results indicate that the Ad-GDNF treatment prevented motor neuron loss with preserving survival p-Akt signal and without affecting caspase activations, suggesting a future possibility for the therapy of the disease.

  17. High Intensity Beam Test of Low Z Materials for the Upgrade of SPS-to-LHC Transfer Line Collimators and LHC Injection Absorbers

    CERN Document Server

    Maciariello, Fausto; Butcher, Mark; Calviani, Marco; Folch, Ramon; Kain, Verena; Karagiannis, Konstantinos; Lamas Garcia, Inigo; Lechner, Anton; Nuiry, Francois-Xavier; Steele, Genevieve; Uythoven, Jan

    2016-01-01

    In the framework of the LHC Injector Upgrade (LIU) and High-Luminosity LHC (HL-LHC) project, the collimators in the SPS-to LHC transfer lines will undergo important modifications. The changes to these collimators will allow them to cope with beam brightness and intensity levels much increased with respect to their original design parameters: nominal and ultimate LHC. The necessity for replacement of the current materials will need to be confirmed by a test in the High Radiation to Materials (HRM) facility at CERN. This test will involve low Z materials (such as Graphite and 3-D Carbon/Carbon composite), and will recreate the worst case scenario those materials could see when directly impacted by High luminosity LHC (HL-LHC) or Batch Compression Merging and Splitting (BCMS) beams. Thermo-structural simulations used for the material studies and research, the experiment preparation phase, the experiment itself, pre irradiation analysis (including ultrasound and metrology tests on the target materials), the resul...

  18. Design and measurements of a fast high-voltage pulse generator for the MedAustron Low Energy Transfer line fast deflector

    CERN Document Server

    Fowler, T; Mueller, F; Kramer, T; Stadlbauer, T

    2012-01-01

    MedAustron, a centre for ion-therapy and research, will comprise an accelerator facility based on a synchrotron for the delivery of protons and light ions for cancer treatment. The Low Energy Beam Transfer line (LEBT) to the synchrotron contains an electrostatic fast deflector (EFE) which, when energized, deviates the continuous beam arriving from the ion source onto a Faraday Cup: the specified voltage is ±3.5 kV. De-energizing the EFE for variable pulse durations from 500 ns up to d.c. allows beam passage for multi-turn injection into the synchrotron. To maintain beam quality in the synchrotron, the EFE pulse generator requires rise and fall times of less than 300 ns between 90 % of peak voltage and a ±1 V level. To achieve this, a pulsed power supply (PKF), with high voltage MOSFET switches connected in a push-pull configuration, will be mounted in close proximity to the deflector itself. A fast, large dynamic range monitoring circuit will verify switching to the ±1 V level and subsequent flat bottom pu...

  19. Validity of the line-pair bar-pattern method in the measurement of the modulation transfer function (MTF) in megavoltage imaging.

    Science.gov (United States)

    Gopal, A; Samant, S S

    2008-01-01

    The measurement of the modulation transfer function (MTF) of an imaging device is a common requirement in evaluating radiographic detector performance. Such measurements are considered mandatory in detector development research, and may also be carried out as part of routine quality assurance (QA) checks of image quality. Traditionally, MTF measurement has been performed by imaging either a narrow slit or a sharp edge in order to generate a line spread function, whose Fourier transform provides the MTF on a near-continuous frequency domain. Much less commonly employed is the method of square-wave line-pair modulations, in which the modulation response to bar resolution targets contained in a bar pattern is used to estimate the MTF at discrete spatial frequencies. While the slit and edge methods offer advantages of accuracy and a well-know standardized protocol for measurement based on several decades of development, their major limitation is the difficult and time-consuming experimental setup that is necessary to ensure accurate measurements. On the other hand, the bar pattern offers the advantage of a quick, simple, and easy measurement without the need for a complex experimental setup, with the main disadvantages of the technique being a pseudo-normalization that may lead to an overestimated MTF, and corrections for removing higher-order frequency harmonics that require interpolating between discrete spatial frequencies. Therefore, bar patterns are traditionally used for qualitative imaging applications like detector QA in terms of relative and arbitrarily defined spatial resolution metrics, while slit and edge methods are preferred for quantitative MTF measurements. Compared to diagnostic x rays, MTF measurements using megavoltage x rays are further complicated by low x-ray attenuation and excessive Compton scattering. In this work, a method to measure the MTF of megavoltage x-ray detectors based on imaging square-wave line pairs with improved near

  20. 10 CFR Appendix G to Part 20 - Requirements for Transfers of Low-Level Radioactive Waste Intended for Disposal at Licensed Land...

    Science.gov (United States)

    2010-01-01

    ... CFR part 172. Information on hazardous, medical, or other waste, required to meet Environmental... container (HIC) means a container commonly designed to meet the structural stability requirements of § 61.56... equipment, mechanical filters, sealed source/devices, and wastes in solidification/stabilization media), the...

  1. Effect of waste mica on transfer factors of {sup 134}Cs to spinach and lettuce; Effet de dechets de mica sur les facteurs de transfert du {sup 134}Cs a l'epinard et la laitue

    Energy Technology Data Exchange (ETDEWEB)

    Sreenivasa Chari, M.; Manjaiah, K.M. [Indian Agricultural Research Institute, Division of Soil Science and Agricultural Chemistry, New Delhi - 110012 (India); Sachdev, P.; Sachdev, M.S. [Indian Agricultural Research Institute, Nuclear Research Laboratory, New Delhi - 110012 (India)

    2011-07-15

    A greenhouse pot culture experiment was conducted to study the effect of graded levels of waste mica (0, 10, 20 and 40 g kg{sup -1}) on reducing the radiocesium uptake by spinach (Spinacia olerecea L) and lettuce (Lactuca sativa L.) grown in {sup 134}Cs-contaminated (at 37 k Bq kg{sup -1} soil) Inceptisols, Vertisols and Ultisols. The biomass yield, and potassium content and its uptake by crops have been significantly improved by waste mica application. The crops grown in Vertisols recorded higher biomass yield, and K content and its uptake as compared with Inceptisols and Ultisols. The average {sup 134}Cs transfer factor values recorded were: 0.21, 0.17 and 0.26 at the first cutting, 0.15, 0.12 and 0.28 at the second cutting and 0.07, 0.05 and 0.23 at the third cutting from Inceptisols, Vertisols and Ultisols, respectively. Waste mica significantly suppressed radiocesium uptake, the effect being more pronounced at 40 g mica kg{sup -1} soil. There exists an inverse relationship between the {sup 134}Cs transfer factors with plant potassium content and also the K uptake by the crops. (authors)

  2. Plasma flow channels at the dawn/dusk polar cap boundaries: momentum transfer on old open field lines and the roles of IMF By and conductivity gradients

    Directory of Open Access Journals (Sweden)

    P. E. Sandholt

    2009-04-01

    Full Text Available Using DMSP F13 data in conjunction with IMF data we investigate the newly discovered channels of enhanced (1.5–3 km/s antisunward convection occurring at the dawn (06:00–09:00 MLT or dusk (15:00–18:00 MLT flanks of the polar cap for different combinations of IMF By polarity, hemisphere (NH/SH and the dawn/dusk MLTs. Dawn-side cases where this flow channel appears occur for the following combinations: NH-dawn/By>0 and SH-dawn/By<0. The dusk-side cases are: NH-dusk/By<0 and SH-dusk/By>0. The flow channels are placed in the context of particle precipitation regimes/boundaries and ionospheric conductivity gradients. They are found to be threaded by "old open field lines" ("time since reconnection" >10 min characterized by polar rain precipitation. In the dawn-side cases (NH-dawn/By>0 and SH-dawn/By<0 and in a Parker spiral field, the polar rain contains the "solar wind strahl" component. The convection enhancement is attributed to the Pedersen current closure of Birkeland current sheets (C1 and C2 in the polar cap (C1 and at the polar cap boundary (C2. The low ionospheric conductivity in the polar cap, particularly in the winter hemisphere, is compensated by an enhanced electric field driving the flow channel there. This is momentum transfer from the solar wind via dynamo action taking place in the combined current system of the high- and low-latitude boundary layers (HBL/LLBL. The conductivity gradient at the polar cap boundary contributes to establishing the convection channel and the associated enhancement of the dawn-dusk convection asymmetry extending beyond the dawn-dusk terminator during intervals of nonzero IMF By component. The HBL/LLBL-ionosphere coupling via Birkeland currents C1/C2 is a source of dawn-dusk convection asymmetry and Svalgaard-Mansurov effect which must be added to the effect of magnetic tension acting on "newly open field lines".

  3. Researches on nuclear wastes. Knowledge gained and perspectives at the 2006 date line; Recherches sur les dechets nucleaires acquis et perspectives a l'echeance 2006

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2006-07-01

    The law from December 30, 1991, precisely defines 3 axes of researches for the management of high level and long-lived radioactive wastes: separation/transmutation, surface storage and underground disposal. A global evaluation report about these researches is to be supplied in 2006 by the French government to the Parliament. The responsibility of these researches is given to the French atomic energy commission (CEA) and to the national agency for radioactive wastes (ANDRA) who have to coordinate their works with other research organizations and industrialists. The aim of this colloquium is to make a status of the scientific knowledge gained before the implementation of the public and parliamentary debates on nuclear wastes management. This document gathers the presentations (slides) given at the colloquium and dealing with: separation/transmutation, storage and conditioning of waste packages; geologic disposal, the inter-disciplinary PACE program of the CNRS; synthesis of the researches evaluation process; general principles for a sustainable management of radioactive wastes; technical experience implemented by industrialists since 15 years; point of view of the nuclear safety authority; international context of nuclear waste management and related researches; a sociological enlightening: researches advance as seen by the public. (J.S.)

  4. Influence of bacteria on lanthanide and actinide transfer from specific soil components (humus, soil minerals and vitrified municipal solid waste incinerator bottom ash) to corn plants: Sr-Nd isotope evidence

    Energy Technology Data Exchange (ETDEWEB)

    Aouad, Georges [Ecole et Observatoire des Sciences de la Terre, Centre de Geochimie de la Surface/CNRS UMR 7517, 1 rue Blessig, 67084 Strasbourg Cedex (France); Stille, Peter [Ecole et Observatoire des Sciences de la Terre, Centre de Geochimie de la Surface/CNRS UMR 7517, 1 rue Blessig, 67084 Strasbourg Cedex (France)]. E-mail: pstille@illite.u-strasbg.fr; Crovisier, Jean-Louis [Ecole et Observatoire des Sciences de la Terre, Centre de Geochimie de la Surface/CNRS UMR 7517, 1 rue Blessig, 67084 Strasbourg Cedex (France); Geoffroy, Valerie A. [UMR 7156 Universite Louis-Pasteur/CNRS, Genetique Moleculaire, Genomique Microbiologie, Departement Micro-organisme, Genomes, Environnement, 28 rue Goethe, 67083 Strasbourg Cedex (France); Meyer, Jean-Marie [UMR 7156 Universite Louis-Pasteur/CNRS, Genetique Moleculaire, Genomique Microbiologie, Departement Micro-organisme, Genomes, Environnement, 28 rue Goethe, 67083 Strasbourg Cedex (France); Lahd-Geagea, Majdi [Ecole et Observatoire des Sciences de la Terre, Centre de Geochimie de la Surface/CNRS UMR 7517, 1 rue Blessig, 67084 Strasbourg Cedex (France)

    2006-11-01

    Experiments have been performed to test the stability of vitrified municipal solid waste (MSW) incinerator bottom ash under the presence of bacteria (Pseudomonas aeruginosa) and plants (corn). The substratum used for the plant growth was a humus-rich soil mixed with vitrified waste. For the first time, information on the stability of waste glasses in the presence of bacteria and plants is given. Results show that inoculated plant samples contained always about two times higher lanthanide and actinide element concentrations. Bacteria support the element transfer since plants growing in inoculated environment developed a smaller root system but have higher trace element concentrations. Compared with the substratum, plants are light rare earth element (LREE) enriched. The vitrified bottom ash has to some extent been corroded by bacteria and plant activities as indicated by the presence of Nd (REE) and Sr from the vitrified waste in the plants. {sup 87}Sr/{sup 86}Sr and {sup 143}Nd/{sup 144}Nd isotope ratios of plants and soil components allow the identification of the corroded soil components and confirm that bacteria accelerate the assimilation of elements from the vitrified bottom ash. These findings are of importance for landfill disposal scenarios, and similar experiments should be performed in order to better constrain the processes of microbially mediated alteration of the MSW glasses in the biosphere.

  5. Nevada Test Site Waste Acceptance Criteria, December 2000

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-12-01

    This document establishes the US Department of Energy, Nevada Operations Office waste acceptance criteria. The waste acceptance criteria provides the requirements, terms, and conditions under which the Nevada Test Site will accept low-level radioactive waste and mixed waste for disposal. It includes requirements for the generator waste certification program, characterization, traceability, waste form, packaging, and transfer. The criteria apply to radioactive waste received at the Nevada Test Site Area 3 and Area 5 Radioactive Waste Management Sites for storage or disposal.

  6. A novel method of artery stenosis diagnosis using transfer function and support vector machine based on transmission line model: A numerical simulation and validation study.

    Science.gov (United States)

    Xiao, Hanguang; Avolio, Alberto; Huang, Decai

    2016-06-01

    Transfer function (TF) is an important parameter for the analysis and understanding of hemodynamics when arterial stenosis exists in human arterial tree. Aimed to validate the feasibility of using TF to diagnose arterial stenosis, the forward problem and inverse problem were simulated and discussed. A calculation method of TF between ascending aorta and any other artery was proposed based on a 55 segment transmission line model (TLM) of human artery tree. The effects of artery stenosis on TF were studied in two aspects: stenosis degree and position. The degree of arterial stenosis was specified to be 10-90% in three representative arteries: carotid, aorta and iliac artery, respectively. In order to validate the feasibility of diagnosis of artery stenosis using TF and support vector machine (SVM), a database of TF was established to simulate the real conditions of artery stenosis based on the TLM model. And a diagnosis model of artery stenosis was built by using SVM and the database. The simulating results showed the modulus and phase of TF were decreasing sharply from frequency 2 to 10Hz with the stenosis degree increasing and displayed their unique and nonlinear characteristics when frequency is higher than 10Hz. The diagnosis results showed the average accuracy was above 76% for the stenosis from 10% to 90% degree, and the diagnosis accuracies of moderate (50%) and serious (90%) stenosis were 87% and 99%, respectively. When the stenosis degree increased to 90%, the accuracy of stenosis localization reached up to 94% for most of arteries. The proposed method of combining TF and SVM is a theoretically feasible method for diagnosis of artery stenosis. Copyright © 2016 Elsevier Ireland Ltd. All rights reserved.

  7. Case Study in Corporate Memory Recovery: Hanford Tank Farms Miscellaneous Underground Waste Storage Tanks - 15344

    Energy Technology Data Exchange (ETDEWEB)

    Washenfelder, D. J.; Johnson, J. M.; Turknett, J. C.; Barnes, T. J.; Duncan, K. G.

    2015-01-07

    In addition to managing the 177 underground waste storage tanks containing 212,000 m3 (56 million gal) of radioactive waste at the U. S. Department of Energy’s Hanford Site 200 Area Tank Farms, Washington River Protection Solutions LLC is responsible for managing numerous small catch tanks and special surveillance facilities. These are collectively known as “MUSTs” - Miscellaneous Underground Storage Tanks. The MUSTs typically collected drainage and flushes during waste transfer system piping changes; special surveillance facilities supported Tank Farm processes including post-World War II uranium recovery and later fission product recovery from tank wastes. Most were removed from service following deactivation of the single-shell tank system in 1980 and stabilized by pumping the remaining liquids from them. The MUSTs were isolated by blanking connecting transfer lines and adding weatherproofing to prevent rainwater entry. Over the next 30 years MUST operating records were dispersed into large electronic databases or transferred to the National Archives Regional Center in Seattle, Washington. During 2014 an effort to reacquire the historical bases for the MUSTs’ published waste volumes was undertaken. Corporate Memory Recovery from a variety of record sources allowed waste volumes to be initially determined for 21 MUSTs, and waste volumes to be adjusted for 37 others. Precursors and symptoms of Corporate Memory Loss were identified in the context of MUST records recovery.

  8. C-tank transfers: Transuranic sludge removal from the C-1, C-2, and W-23 waste storage tanks at Oak Ridge National Laboratory, Oak Ridge, Tennessee

    Energy Technology Data Exchange (ETDEWEB)

    Dahl, T.L.; Lay, A.C.; Taylor, S.A.; Moore, J.W.

    1999-05-01

    Two fluidic pulse jet mixing systems were used to successfully mobilize remote-handled transuranic sludge for retrieval from three 50,000-gal horizontal waste storage tanks at Oak Ridge National Laboratory (ORNL). The results of this operation indicate that the pulse jet system should be considered for mixing and bulk retrieval of sludges in other vertical and horizontal waste tanks at ORNL and at other U.S. Department of Energy sites.

  9. Inventory of heavy metal content in organic waste applied as fertilizer in agriculture: evaluating the risk of transfer into the food chain.

    Science.gov (United States)

    Lopes, Carla; Herva, Marta; Franco-Uría, Amaya; Roca, Enrique

    2011-07-01

    In this work, an environmental risk assessment of reusing organic waste of differing origins and raw materials as agricultural fertilizers was carried out. An inventory of the heavy metal content in different organic wastes (i.e., compost, sludge, or manure) from more than 80 studies at different locations worldwide is presented. The risk analysis was developed by considering the heavy metal (primarily Cd, Cu, Ni, Pb, and Zn) concentrations in different organic residues to assess their potential environmental accumulation and biotransfer to the food chain and humans. A multi-compartment model was used to estimate the fate and distribution of metals in different environmental compartments, and a multi-pathway model was used to predict human exposure. The obtained hazard index for each waste was concerning in many cases, especially in the sludge samples that yielded an average value of 0.64. Among the metals, Zn was the main contributor to total risk in all organic wastes due to its high concentration in the residues and high biotransfer potential. Other more toxic metals, like Cd or Pb, represented a negligible contribution. These results suggest that the Zn content in organic waste should be reduced or more heavily regulated to guarantee the safe management and reuse of waste residues according to the current policies promoted by the European Union.

  10. Remaining Sites Verification Package for the 100-F-26:10, 1607-F3 Sanitary Sewer Pipelines (182-F, 183-F, and 151-F Sanitary Sewer Lines), Waste Site Reclassification Form 2007-028

    Energy Technology Data Exchange (ETDEWEB)

    L. M. Dittmer

    2007-12-03

    The 100-F-26:10 waste site includes sanitary sewer lines that serviced the former 182-F, 183-F, and 151-F Buildings. In accordance with this evaluation, the verification sampling results support a reclassification of this site to Interim Closed Out. The results of verification sampling show that residual contaminant concentrations do not preclude any future uses and allow for unrestricted use of shallow zone soils. The results also demonstrate that residual contaminant concentrations are protective of groundwater and the Columbia River.

  11. Exploring the immediate and long-term impact on bacterial communities in soil amended with animal and urban organic waste fertilizers using pyrosequencing and screening for horizontal transfer of antibiotic resistance

    DEFF Research Database (Denmark)

    Riber, Leise; Poulsen, Pernille H. B.; Al-Soud, Waleed A.

    2014-01-01

    multiresistant, also in unfertilized soil. Finally, the ability of a P.putida strain to take up resistance genes from indigenous soil bacteria by horizontal gene transfer was present only in week 0, indicating a temporary increase in prevalence of transferable antibiotic resistance genes....... these changes, prevalence of antibiotic- and mercury-resistant pseudomonads was investigated. Fertilizer amendment had a transient impact on the resistance profile of the soil community; abundance of resistant isolates decreased with time after fertilizer application, but persistent strains appeared......We investigated immediate and long-term effects on bacterial populations of soil amended with cattle manure, sewage sludge or municipal solid waste compost in an ongoing agricultural field trial. Soils were sampled in weeks 0, 3, 9 and 29 after fertilizer application. Pseudomonas isolates were...

  12. State Waste Discharge Permit application, 100-N Sewage Lagoon

    Energy Technology Data Exchange (ETDEWEB)

    1994-06-01

    As part of the Hanford Federal Facility Agreement and Consent Order negotiations (Ecology et al. 1994), the US Department of Energy, Richland Operations Office, the US Environmental Protection Agency, and the Washington State Department of Ecology agreed that liquid effluent discharges to the ground on the Hanford Site which affect groundwater or have the potential to affect groundwater would be subject to permitting under the structure of Chapter 173--216 (or 173--218 where applicable) of the Washington Administrative Code, the State Waste Discharge Permit Program. As a result of this decision, the Washington State Department of Ecology and the US Department of Energy, Richland Operations Office entered into Consent Order No. DE 91NM-177, (Ecology and DOE-RL 1991). This document constitutes the State Waste Discharge Permit application for the 100-N Sewage Lagoon. Since the influent to the sewer lagoon is domestic waste water, the State Waste Discharge Permit application for Public Owned Treatment Works Discharges to Land was used. Although the 100-N Sewage Lagoon is not a Public Owned Treatment Works, the Public Owned Treatment Works application is more applicable than the application for industrial waste water. The 100-N Sewage Lagoon serves the 100-N Area and other Hanford Site areas by receiving domestic waste from two sources. A network of sanitary sewer piping and lift stations transfers domestic waste water from the 100-N Area buildings directly to the 100-N Sewage Lagoon. Waste is also received by trucks that transport domestic waste pumped from on site septic tanks and holding tanks. Three ponds comprise the 100-N Sewage Lagoon treatment system. These include a lined aeration pond and stabilization pond, as well as an unlined infiltration pond. Both piped-in and trucked-in domestic waste is discharged directly into the aeration pond.

  13. Waste Sites - Municipal Waste Operations

    Data.gov (United States)

    NSGIC Education | GIS Inventory — A Municipal Waste Operation is a DEP primary facility type related to the Waste Management Municipal Waste Program. The sub-facility types related to Municipal Waste...

  14. Impact of cementitious materials decalcification on transfer properties: application to radioactive waste deep repository; Influence de la decalcification de materiaux cimentaires sur les proprietes de transfert: application au stockage profond de dechets radioactifs

    Energy Technology Data Exchange (ETDEWEB)

    Perlot, C

    2005-09-15

    Cementitious materials have been selected to compose the engineering barrier system (EBS) of the French radioactive waste deep repository, because of concrete physico-chemical properties: the hydrates of the cementitious matrix and the pH of the pore solution contribute to radionuclides retention; furthermore the compactness of these materials limits elements transport. The confinement capacity of the system has to be assessed while a period at least equivalent to waste activity (up to 100.000 years). His durability was sustained by the evolution of transfer properties in accordance with cementitious materials decalcification, alteration that expresses structure long-term behavior. Then, two degradation modes were carried out, taking into account the different physical and chemical solicitations imposed by the host formation. The first mode, a static one, was an accelerated decalcification test using nitrate ammonium solution. It replicates the EBS alteration dues to underground water. Degradation kinetic was estimated by the amount of calcium leached and the measurement of the calcium hydroxide dissolution front. To evaluate the decalcification impact, samples were characterized before and after degradation in term of microstructure (porosity, pores size distribution) and of transfer properties (diffusivity, gas and water permeability). The influence of cement nature (ordinary Portland cement, blended cement) and aggregates type (lime or siliceous) was observed: experiments were repeated on different mortars mixes. On this occasion, an essential reflection on this test metrology was led. The second mode, a dynamical degradation, was performed with an environmental permeameter. It recreates the EBS solicitations ensured during the re-saturation period, distinguished by the hydraulic pressure imposed by the geologic layer and the waste exothermicity. This apparatus, based on triaxial cell functioning, allows applying on samples pressure drop between 2 and 10 MPa and

  15. {open_quotes}Horizontal{close_quotes} gene transfer from a transgenic potato line to a bacterial pathogen (Erwinia chrysanthemi) occurs - if at all - at an extremely low frequency

    Energy Technology Data Exchange (ETDEWEB)

    Schlueter, K.; Fuetterer, J.; Potrykus, I. [Institute of Plant Sciences, Zuerich (Switzerland)

    1995-10-01

    The frequency of possible {open_quotes}horizontal{close_quotes} gene transfer between a plant and a tightly associated bacterial pathogen was studied in a model system consisting of transgenic Solanum tuberosum, containing a {beta}-lactamase gene linked to a pBR322 origin of replication, and Erwinia chrysanthemi. This experimental system offers optimal conditions for the detection of possible horizontal gene transfer events, even when they occur at very low frequency. Horizontal gene transfer was not detected under conditions mimicking a {open_quotes}natural{close_quotes} infection. The gradual, stepwise alteration of artificial, positive control conditions to idealized natural conditions, however, allowed the characterization of factors that affected gene transfer, and revealed a gradual decrease of the gene transfer frequency from 6.3 x 10{sup -2} under optimal control conditions to a calculated 2.0 x 10{sub -17} under idealized natural conditions. These data, in combination with other published studies, argue that horizontal gene transfer is so rare as to be essentially irrelevant to any realistic assessment of the risk involved in release experiments involving transgenic plants. 22 refs., 3 figs., 2 tabs.

  16. Residential Waste

    DEFF Research Database (Denmark)

    Christensen, Thomas Højlund; Fruergaard, Thilde; Matsufuji, Y.

    2011-01-01

    Residential waste comes from residential areas with multi-family and single-family housing and includes four types of waste: household waste, garden waste, bulky waste and household hazardous waste. Typical unit generation rates, material composition, chemical composition and determining factors...... are discussed in this chapter. Characterizing residential waste is faced with the problem that many residences already divert some waste away from the official collection systems, for example performing home composting of vegetable waste and garden waste, having their bundled newspaper picked up by the scouts...... twice a year or bringing their used furniture to the flea markets organized by charity clubs. Thus, much of the data available on residential waste represents collected waste and not necessarily all generated waste. The latter can only be characterized by careful studies directly at the source...

  17. NEVADA TEST SITE WASTE ACCEPTANCE CRITERIA

    Energy Technology Data Exchange (ETDEWEB)

    U.S. DEPARTMENT OF ENERGY, NATIONAL NUCLEAR SECURITY ADMINISTRATION, NEVADA SITE OFFICE

    2005-07-01

    This document establishes the U. S. Department of Energy, National Nuclear Security Administration Nevada Site Office (NNSA/NSO) waste acceptance criteria (WAC). The WAC provides the requirements, terms, and conditions under which the Nevada Test Site will accept low-level radioactive and mixed waste for disposal. Mixed waste generated within the State of Nevada by NNSA/NSO activities is accepted for disposal. It includes requirements for the generator waste certification program, characterization, traceability, waste form, packaging, and transfer. The criteria apply to radioactive waste received at the Nevada Test Site Area 3 and Area 5 Radioactive Waste Management Site for storage or disposal.

  18. 75 FR 39680 - Houston Pipe Line Company LP, Worsham-Steed Gas Storage, L.P., Energy Transfer Fuel, LP, Mid...

    Science.gov (United States)

    2010-07-12

    ... Storage, L.P., Energy Transfer Fuel, LP, Mid Continent Market Center, L.L.C., Oasis Pipeline, LP (Not... From the Federal Register Online via the Government Publishing Office ] DEPARTMENT OF ENERGY Federal Energy Regulatory Commission [Docket No. PR10-44-000; Docket No. PR10-46-000; Docket No. PR10-48...

  19. The Effects of an Animation-Based On-Line Learning Environment on Transfer of Knowledge and on Motivation for Science and Technology Learning

    Science.gov (United States)

    Rosen, Yigal

    2009-01-01

    The study described here is among the first of its kind to investigate systematically the effect of learning with integrated animations on transfer of knowledge and on motivation to learn science and technology. Four hundred eighteen 5th and 7th grade students across Israel participated in a study. Students in the experimental group participated…

  20. Three-dimensional Radiative Transfer Simulations of the Scattering Polarization of the Hydrogen Lyalpha Line in a Magnetohydrodynamic Model of the Chromosphere-Corona Transition Region

    Czech Academy of Sciences Publication Activity Database

    Štěpán, Jiří; Trujillo Bueno, J.; Leenaarts, J.; Carlsson, M.

    2015-01-01

    Roč. 803, č. 2 (2015), 65/1-65/15 ISSN 0004-637X R&D Projects: GA ČR GPP209/12/P741 Grant - others:EU(XE) COST action MP1104 Institutional support: RVO:67985815 Keywords : polarization * radiative transfer * scattering Subject RIV: BN - Astronomy, Celestial Mechanics, Astrophysics Impact factor: 5.909, year: 2015

  1. Enhanced Waste Tank Level Model

    Energy Technology Data Exchange (ETDEWEB)

    Duignan, M.R.

    1999-06-24

    'With the increased sensitivity of waste-level measurements in the H-Area Tanks and with periods of isolation, when no mass transfer occurred for certain tanks, waste-level changes have been recorded with are unexplained.'

  2. Hazardous Waste

    Science.gov (United States)

    ... you throw these substances away, they become hazardous waste. Some hazardous wastes come from products in our homes. Our garbage can include such hazardous wastes as old batteries, bug spray cans and paint ...

  3. Radioactive waste storage issues

    Energy Technology Data Exchange (ETDEWEB)

    Kunz, Daniel E. [Colorado Christian Univ., Lakewood, CO (United States)

    1994-08-15

    In the United States we generate greater than 500 million tons of toxic waste per year which pose a threat to human health and the environment. Some of the most toxic of these wastes are those that are radioactively contaminated. This thesis explores the need for permanent disposal facilities to isolate radioactive waste materials that are being stored temporarily, and therefore potentially unsafely, at generating facilities. Because of current controversies involving the interstate transfer of toxic waste, more states are restricting the flow of wastes into - their borders with the resultant outcome of requiring the management (storage and disposal) of wastes generated solely within a state`s boundary to remain there. The purpose of this project is to study nuclear waste storage issues and public perceptions of this important matter. Temporary storage at generating facilities is a cause for safety concerns and underscores, the need for the opening of permanent disposal sites. Political controversies and public concern are forcing states to look within their own borders to find solutions to this difficult problem. Permanent disposal or retrievable storage for radioactive waste may become a necessity in the near future in Colorado. Suitable areas that could support - a nuclear storage/disposal site need to be explored to make certain the health, safety and environment of our citizens now, and that of future generations, will be protected.

  4. Transfer into the biosphere of radionuclides released from deep storage of radioactive wastes. Bibliographical study; Transfert dans la biosphere des radionucleides issus des stockages profonds de dechets radioactifs. Etude bibliographique

    Energy Technology Data Exchange (ETDEWEB)

    Guedon, V.; Siclet, F.

    1995-03-01

    Most countries with civilian nuclear programs today are encountering difficulty in implementing a nuclear waste management policy that is both technically safe in the long term and accepted by the public. To meet both criteria, the solution most generally envisaged is deep storage either of untreated spent nuclear fuel or of highly radioactive wastes resulting from reprocessing. In order to predict the potential impact of such storage on man, one needs to understand the path followed by radionuclides in the geosphere, and later in the biosphere. Given the time scales involved and the critical nature of the elements concerned, it is indispensable to turn to mathematical modeling of the phenomena. This report presents what is hoped to be a complete inventory of the radionuclides contained in ``high level`` wastes (categories B AND C). The elements concerned in studies on deep storage are essentially long-life radionuclides (both actinides and certain fission and activation products). Their physico-chemical characteristics and their behavior in various ecological compartments are examined. Bibliographical data bearing on: solubility (in an oxidizing, reducing medium), distribution factors (water/rock-sediment-soil), concentration and transfer factors (in aquatic and terrestrial mediums), dose conversion factors (in the case of internal and external irradiation), principal paths of exposure for each radionuclide studied, are presented in this report. Initial results from international projects to model what happens to radionuclides in the biosphere are also presented. In general, they are optimistic as to the future, but nonetheless point to a need to improve the conceptual base of the models, to ensure that all major phenomena and processes are taken into consideration and to examine any possible amplification (author). 67 refs., 39 figs., 20 tabs.

  5. Remaining Sites Verification Package for the 100-C-9:1 Main Process Sewer Collection Line, Waste Site Reclassification Form 2004-012

    Energy Technology Data Exchange (ETDEWEB)

    L. M. Dittmer

    2007-06-11

    The 100-C-9:1 main process sewer pipeline, also known as the twin box culvert, was a dual reinforced process sewer that collected process effluent from the 183-C and 190-C water treatment facilities, discharging at the 132-C-2 Outfall. For remedial action purposes, the 100-C-9:1 waste site was subdivided into northern and southern sections. The 100-C-9:1 subsite has been remediated to achieve the remedial action objectives specified in the Remaining Sites ROD. The results of verification sampling show that residual contaminant concentrations do not preclude any future uses and allow for unrestricted use of shallow zone soils. The results also demonstrate that residual contaminant concentrations are protective of groundwater and the Columbia River.

  6. Interim safety equipment list for 241-C-106 waste retrieval, project W-320

    Energy Technology Data Exchange (ETDEWEB)

    Conner, J.C.

    1996-01-25

    The purpose of this supporting document is to provide safety classifications for systems, structures, and components of the Tank 241-C-106 Waste Retrieval Sluicing System (WRSS) and to document the methodology used to develop these safety classifications. The WRSS requires two transfer lines, one to carry sluiced waste slurry to tank 241-AY-102 and the other to return supernatant to tank 241-C-106; pumps in each tank; sluicers to direct the supernatant stream inside tank 241-C-106; a slurry distributor in tank 241-AY-102; heating, ventilation, and air conditioning for tank 241-C-106; and instrumentation and control devices.

  7. Potential for transfer of Escherichia coli O157:H7, Listeria monocytogenes and Salmonella Senftenberg from contaminated food waste derived compost and anaerobic digestate liquid to lettuce plants.

    Science.gov (United States)

    Murphy, Suzannah; Gaffney, Michael T; Fanning, Seamus; Burgess, Catherine M

    2016-10-01

    The diversion of food wastes from landfill to sustainable disposal methods, such as composting and anaerobic digestion, has led to an increase in the soil amendment products that are now commercially available and which are derived from both of these processes. The use of such products as soil amendments during the production of ready-to-eat (RTE) crops is increasing worldwide. The aim of this study was to investigate the potential of three well-recognised bacterial pathogens of importance to public health, namely Escherichia coli O157:H7, Salmonella Senftenberg and Listeria monocytogenes, to become internalised in lettuce plants from peat growing media amended with contaminated food waste derived compost and anaerobic digestion liquid. The results demonstrated both S. Senftenberg and E. coli O157:H7 are capable of internalisation at lower inoculation levels, compared to previous studies. The internalisation was visualised through confocal microscopy. Internalisation of L. monocytogenes did not occur, however significant levels of L. monocytogenes contamination occurred on the non-sterilised plant surface. Assessing the internalisation potential for each of these pathogens, through the compost and anaerobic digestate matrices, allows for better risk assessment of the use of these products in a horticultural setting. Copyright © 2016 Elsevier Ltd. All rights reserved.

  8. Waste Management Program. Technical progress report, October-December 1982

    Energy Technology Data Exchange (ETDEWEB)

    None

    1983-07-01

    This quarterly report provides current information on operations and development programs for the management of radioactive wastes from operation of the Savannah River Plant and offplant participants. The studies on environmental and safety assessments, in situ storage or disposal, waste from development and characterization, process and equipment development, and low-level waste management are a part of the Long-Term Waste Management Technology Program. The following studies are reported for the SR Interim Waste Operations Program: surveillance and maintenance, waste concentration, low-level effluent waste, tank replacement/waste transfer, and solid waste storage and related activities.

  9. Waste Management Program. Technical progress report, Aporil-June 1983

    Energy Technology Data Exchange (ETDEWEB)

    None

    1984-02-01

    This quarterly report provides current information on operations and development programs for the management of radioactive wastes from operation of the Savannah River Plant. The studies on environmental and safety assessments, process and equipment development, TRU waste, and low-level waste are a part of the Long-Term Waste Management Technology Program. The following studies are reported for the SR Interim Waste Operations Program: surveillance and maintenance, waste concentration, low-level effluent waste, tank replacement/waste transfer, and solid waste storage and related activities.

  10. Exploring the immediate and long-term impact on bacterial communities in soil amended with animal and urban organic waste fertilizers using pyrosequencing and screening for horizontal transfer of antibiotic resistance.

    Science.gov (United States)

    Riber, Leise; Poulsen, Pernille H B; Al-Soud, Waleed A; Skov Hansen, Lea B; Bergmark, Lasse; Brejnrod, Asker; Norman, Anders; Hansen, Lars H; Magid, Jakob; Sørensen, Søren J

    2014-10-01

    We investigated immediate and long-term effects on bacterial populations of soil amended with cattle manure, sewage sludge or municipal solid waste compost in an ongoing agricultural field trial. Soils were sampled in weeks 0, 3, 9 and 29 after fertilizer application. Pseudomonas isolates were enumerated, and the impact on soil bacterial community structure was investigated using 16S rRNA amplicon pyrosequencing. Bacterial community structure at phylum level remained mostly unaffected. Actinobacteria, Proteobacteria and Chloroflexi were the most prevalent phyla significantly responding to sampling time. Seasonal changes seemed to prevail with decreasing bacterial richness in week 9 followed by a significant increase in week 29 (springtime). The Pseudomonas population richness seemed temporarily affected by fertilizer treatments, especially in sludge- and compost-amended soils. To explain these changes, prevalence of antibiotic- and mercury-resistant pseudomonads was investigated. Fertilizer amendment had a transient impact on the resistance profile of the soil community; abundance of resistant isolates decreased with time after fertilizer application, but persistent strains appeared multiresistant, also in unfertilized soil. Finally, the ability of a P. putida strain to take up resistance genes from indigenous soil bacteria by horizontal gene transfer was present only in week 0, indicating a temporary increase in prevalence of transferable antibiotic resistance genes. © 2014 Federation of European Microbiological Societies. Published by John Wiley & Sons Ltd. All rights reserved.

  11. PORTA: A three-dimensional multilevel radiative transfer code for modeling the intensity and polarization of spectral lines with massively parallel computers

    Czech Academy of Sciences Publication Activity Database

    Štěpán, Jiří; Trujillo Bueno, J.

    2013-01-01

    Roč. 557, September (2013), A143/1-A143/15 ISSN 0004-6361 R&D Projects: GA ČR GPP209/12/P741 Grant - others:EU(XE) COST action MP1104 Institutional support: RVO:67985815 Keywords : line formation * magnetic fields * numerical methods Subject RIV: BN - Astronomy, Celestial Mechanics, Astrophysics Impact factor: 4.479, year: 2013

  12. Co-transfer of resistance to high concentrations of copper and first-line antibiotics among Enterococcus from different origins (humans, animals, the environment and foods) and clonal lineages.

    Science.gov (United States)

    Silveira, Eduarda; Freitas, Ana R; Antunes, Patrícia; Barros, Mariana; Campos, Joana; Coque, Teresa M; Peixe, Luísa; Novais, Carla

    2014-04-01

    We studied the occurrence of diverse copper (Cu) tolerance genes from Gram-positive bacteria and their co-transfer with antibiotic resistance genes among Enterococcus from diverse sources. Enterococcus (n = 922) of several species and from human, animal, environment and food samples were included. Antimicrobial and CuSO4 susceptibility and conjugation assays were performed by standard procedures, bacterial screening of Cu and antibiotic resistance genes by PCR, and clonality by PFGE/multilocus sequence typing. tcrB and cueO genes occurred in 15% (n = 137/922) and 14% (n = 128/922) of isolates, respectively, with the highest occurrence in piggeries (P transfer of Cu tolerance (associated with tcrB, cueO or an unknown mechanism) with erythromycin, tetracycline, vancomycin, aminoglycosides or ampicillin resistance was demonstrated. A variety of PFGE types was detected among isolates carrying Cu tolerance mechanisms, some identified in sequence types (STs) often linked to human infections (E. faecium from ST18 and ST78 clonal lineages and E. faecalis clonal complex 2). Cu tolerance might contribute to the selection/maintenance of multidrug-resistant Enterococcus (including resistance to first-line antibiotics used to treat enterococcal infections) due to the use of Cu compounds (e.g. antiseptics/animal feed supplements). The distribution of the multicopper oxidase cueO and the co-transfer of ampicillin resistance along with Cu tolerance genes are described for the first time.

  13. Radioactive waste material melter apparatus

    Science.gov (United States)

    Newman, D.F.; Ross, W.A.

    1990-04-24

    An apparatus for preparing metallic radioactive waste material for storage is disclosed. The radioactive waste material is placed in a radiation shielded enclosure. The waste material is then melted with a plasma torch and cast into a plurality of successive horizontal layers in a mold to form a radioactive ingot in the shape of a spent nuclear fuel rod storage canister. The apparatus comprises a radiation shielded enclosure having an opening adapted for receiving a conventional transfer cask within which radioactive waste material is transferred to the apparatus. A plasma torch is mounted within the enclosure. A mold is also received within the enclosure for receiving the melted waste material and cooling it to form an ingot. The enclosure is preferably constructed in at least two parts to enable easy transport of the apparatus from one nuclear site to another. 8 figs.

  14. Solid Waste Management in Petroleum Refineries

    OpenAIRE

    Jadea S. Alshammari; Fatma K.A Gad; Ahmed A.M. Elgibaly; Abdul R. Khan

    2008-01-01

    Waste management became focus of attention of many researchers and scientists in the last half century due to its vital importance. Waste management covered waste source reduction in general, by recycling, reusing, composting, incineration with or without energy recovery, fuel production and land filling. A common approach of waste management models were for specific problems with a limited scope (like assignment of generating sources to landfills, transfer stations sitting, site selection fo...

  15. Characterization of the 3p12.3-pcen region associated with tumor suppression in a novel ovarian cancer cell line model genetically modified by chromosome 3 fragment transfer.

    Science.gov (United States)

    Cody, Neal A L; Shen, Zhen; Ripeau, Jean-Sebastien; Provencher, Diane M; Mes-Masson, Anne-Marie; Chevrette, Mario; Tonin, Patricia N

    2009-12-01

    The genetic analysis of nontumorigenic radiation hybrids generated by transfer of chromosome 3 fragments into the tumorigenic OV-90 ovarian cancer cell line identified the 3p12.3-pcen region as a candidate tumor suppressor gene (TSG) locus. In the present study, polymorphic microsatellite repeat analysis of the hybrids further defined the 3p12.3-pcen interval to a 16.1 Mb common region containing 12 known or hypothetical genes: 3ptel-ROBO2-ROBO1-GBE1-CADM2-VGLL3-CHMP2B-POU1F1-HTR1F-CGGBP1-ZNF654-C3orf38-EPHA3-3pcen. Seven of these genes, ROBO1, GBE1, VGLL3, CHMP2B, CGGBP1, ZNF654, and C3orf38, exhibited gene expression in the hybrids, placing them as top TSG candidates for further analysis. The expression of all but one (VGLL3) of these genes was also detected in the parental OV-90 cell line. Mutations were not identified in a comparative sequence analysis of the predicted protein coding regions of these candidates in OV-90 and donor normal chromosome 3 contig. However, the nondeleterious sequence variants identified in the transcribed regions distinguished parent of origin alleles for ROBO1, VGLL3, CHMP2B, and CGGBP1 and cDNA sequencing of the hybrids revealed biallelic expression of these genes. Interestingly, underexpression of VGLL3 and ZNF654 were observed in malignant ovarian tumor samples as compared with primary cultures of normal ovarian surface epithelial cells or benign ovarian tumors, and this occurred regardless of allelic content of 3p12.3-pcen. The results taken together suggest that dysregulation of VGLL3 and/or ZNF654 expression may have affected pathways important in ovarian tumorigenesis which was offset by the transfer of chromosome 3 fragments in OV-90, a cell line hemizygous for 3p.

  16. Nevada Test Site Waste Acceptance Criteria

    Energy Technology Data Exchange (ETDEWEB)

    U. S. Department of Energy, National Nuclear Security Administration Nevada Site Office

    2005-10-01

    This document establishes the U.S. Department of Energy (DOE), National Nuclear Security Administration Nevada Site Office (NNSA/NSO) waste acceptance criteria (WAC). The WAC provides the requirements, terms, and conditions under which the Nevada Test Site (NTS) will accept low-level radioactive (LLW) and mixed waste (MW) for disposal. It includes requirements for the generator waste certification program, characterization, traceability, waste form, packaging, and transfer. The criteria apply to radioactive waste received at the NTS Area 3 and Area 5 Radioactive Waste Management Complex (RWMC) for storage or disposal.

  17. Antigen Presentation by Individually Transferred HLA Class I Genes in HLA-A, HLA-B, HLA-C Null Human Cell Line Generated Using the Multiplex CRISPR-Cas9 System.

    Science.gov (United States)

    Hong, Cheol-Hwa; Sohn, Hyun-Jung; Lee, Hyun-Joo; Cho, Hyun-Il; Kim, Tai-Gyu

    Human leukocyte antigens (HLAs) are essential immune molecules that affect transplantation and adoptive immunotherapy. When hematopoietic stem cells or organs are transplanted with HLA-mismatched recipients, graft-versus-host disease or graft rejection can be induced by allogeneic immune responses. The function of each HLA allele has been studied using HLA-deficient cells generated from mutant cell lines or by RNA interference, zinc finger nuclease, and the CRISPR/Cas9 system. To improve HLA gene editing, we attempted to generate an HLA class I null cell line using the multiplex CRISPR/Cas9 system by targeting exons 2 and 3 of HLA-A, HLA-B, and HLA-C genes simultaneously. Multiplex HLA editing could induce the complete elimination of HLA class I genes by bi-allelic gene disruption on target sites which was defined by flow cytometry and target-specific polymerase chain reaction. Furthermore, artificial antigen-presenting cells were generated by transfer of a single HLA class I allele and co-stimulatory molecules into this novel HLA class I null cell line. Artificial antigen-presenting cells showed HLA-restricted antigen presentation following antigen processing and were successfully used for the efficient generation of tumor antigen-specific cytotoxic T cells in vitro. The efficient editing of HLA genes may provide a basis for universal cellular therapies and transplantation.

  18. Guidelines for generators of hazardous chemical waste at LBL and Guidelines for generators of radioactive and mixed waste at LBL

    Energy Technology Data Exchange (ETDEWEB)

    1991-07-01

    The purpose of this document is to provide the acceptance criteria for the transfer of hazardous chemical, radioactive, and mixed waste to Lawrence Berkeley Laboratory's (LBL) Hazardous Waste Handling Facility (HWHF). These guidelines describe how a generator of wastes can meet LBL's acceptance criteria for hazardous chemical, radioactive, and mixed waste. 9 figs.

  19. On-line analysis of gas-phase composition in the combustion chamber and particle emission characteristics during combustion of wood and waste in a small batch reactor.

    Science.gov (United States)

    Ferge, T; Maguhn, J; Hafner, K; Mühlberger, F; Davidovic, M; Warnecke, R; Zimmermann, R

    2005-03-15

    The emission of particulate matter and gaseous compounds during combustion of wood and refuse-derived fuel in a small batch reactor is investigated by laser mass-spectrometric on-line measurement techniques for gas-phase analysis and simultaneous registration of physical aerosol properties (number size distribution). The gas-phase composition is addressed by a laser-based mass spectrometric method, namely, vacuum-UV single-photon ionization time-of-flight mass spectrometry (VUV-SPI-TOFMS). Particle-size distributions are measured with a scanning mobility particle sizer. Furthermore, a photoelectric aerosol sensor is applied for detection of particle-bound polycyclic aromatic hydrocarbons. The different phases of wood combustion are distinguishable by both the chemical profiles of gas-phase components (e.g., polycyclic aromatic hydrocarbons, PAH) and the particle-size distribution. Furthermore, short disturbances of the combustion process due to air supply shortages are investigated regarding their effect on particle-size distribution and gas-phase composition, respectively. It is shown that the combustion conditions strongly influence the particle-size distribution as well as on the emission of particle-bound polycyclic aromatic hydrocarbons.

  20. Transfer of financial obligations for the disposal of nuclear waste and decommissioning of German NPP's. Legal aspects of a trust model; Sicherstellung der finanziellen Entsorgungsvorsorge fuer die Stilllegungs- und Rueckbaukosten der deutschen Kernkraftwerke. Rechtliche Randbedingungen eines Stiftungsmodells

    Energy Technology Data Exchange (ETDEWEB)

    Schewe, Markus; Wiesendahl, Stefan [Kuemmerlein Rechtsanwaelte und Notare, Essen (Germany)

    2015-04-15

    The nuclear power plant operators have to bear the costs associated with the closure and the decommissioning of the German nuclear power plants as well as the costs for the disposal of nuclear waste. For that purpose, the operators have to build up sufficient reserves for the decommissioning phase. These reserves at the end of 2013 amounted to approximately 36 billion Euro. Changing this system is discussed very so often. Last in May 2014, a public debate started dealing with the so called trust model (''Stiftungsmodell''). The press published deliberations of several operators to transfer their entire nuclear business to the Federal Republic of Germany. Under this deliberation the current nuclear power plant operations, as well as closure obligations would be contributed to trust. Further, also the reserves should be ''transferred'' to the trust. RAG-Foundation (RAG-Stiftung) - which will assume the financial obligations in connection with Germany's closure of underground coal mining activities - sometimes is cited as a role model. The article covers elements of German trust law and atomic energy law regarding such deliberations. In trust law e.g. it can be debated whether the trust should be established under public or - as in the case of RAG-Foundation - under private law. In this context we will set out the major differences between those two options. In the public law part we will notably address issues arising from individual licensing requirements for nuclear power plants and focus on questions concerning reliability, requisite qualification and organizational structures.

  1. Waste management

    DEFF Research Database (Denmark)

    Bruun Hansen, Karsten; Jamison, Andrew

    2000-01-01

    The case study deals with public accountability issues connected to household waste management in the municipality of Copenhagen, Denmark.......The case study deals with public accountability issues connected to household waste management in the municipality of Copenhagen, Denmark....

  2. Satellite processing facilities: a new solid-waste planning concept

    Energy Technology Data Exchange (ETDEWEB)

    Brown, D.S.

    The concept of using satellite facilities for regional solid-waste management is a response to the need for realistic long-range planning for resource recovery. A feasibility study was made of a single-line processing facility to determine its efficiency and cost potential. The study concludes that economics require a region large enough to produce adequate waste, the presence of an energy market for the combustible fraction, and an independent and flexible organization. The plan offers an alternative to numerous landfills and long-distance transfer as well as local employment opportunities. Cost estimates of $5 to $12 per ton for the test study are competitive with the cost of operating landfills. Markets for the recovered materials were identified during the study.

  3. Heath monitoring of a glass transfer robot in the mass production line of liquid crystal display using abnormal operating sounds based on wavelet packet transform and artificial neural network

    Science.gov (United States)

    Kim, Eui-Youl; Lee, Young-Joon; Lee, Sang-Kwon

    2012-07-01

    This paper presents the fault detect method of a moving transfer robot in the mass production line of liquid crystal display (LCD) manufacturers based on the wavelet packet transform (WPT) for feature extraction and the artificial neural network (ANN) for fault classification. Most of fault detection methods in a mechanical system have been researched based on the vibration signal. Unlike the existing methodologies, this study aims to minimize the uncertainty of a field engineer's decision making process for determining whether a fault is present or not based on the human auditory perception by developing a fault diagnosis system that uses the abnormal operating sound radiated from a moving transfer robot as a source signal. Abnormal operating sound radiated from a moving transfer robot has been used for this work instead of other source signals such as vibration, acoustic emission, electrical signal, etc. Its advantage as a source signal makes it possible to monitor the status of multiple faults by using only a microphone despite a relatively low sensitivity. In the application of ANN, since it is important to minimize the error of trained ANN in terms of the accuracy of fault diagnosis logic, in the paper, the number of input and target data samples was increased through a regeneration process based on statistical properties, and then the uncorrelated nodes in the input vector were also removed to improve the orthogonality of the input vector based on the entropy based feature selection method. Consequently, it can be concluded that the abnormal operating sound is sufficiently useful as a source signal for the fault diagnosis of mechanical components as well as other source signals.

  4. Food waste

    OpenAIRE

    Arazim, Lukáš

    2015-01-01

    This thesis looks into issues related to food waste and consists of a theoretical and a practical part. Theoretical part aims to provide clear and complex definition of wood waste related problems, summarize current findings in Czech and foreign sources. Introduction chapter explains important terms and legal measures related to this topic. It is followed by description of causes, implications and possibilities in food waste reduction. Main goal of practical part is analyzing food waste in Cz...

  5. Automotive Wastes.

    Science.gov (United States)

    Guigard, Selma E; Shariaty, Pooya; Niknaddaf, Saeid; Lashaki, Masoud Jahandar; Atkinson, John D; Hashisho, Zaher

    2015-10-01

    A review of the literature from 2014 related to automotive wastes is presented. Topics include solid wastes from autobodies and tires as well as vehicle emissions to soil and air as a result of the use of conventional and alternative fuels. Potential toxicological and health risks related to automotive wastes are also discussed.

  6. Radioactive Waste.

    Science.gov (United States)

    Blaylock, B. G.

    1978-01-01

    Presents a literature review of radioactive waste disposal, covering publications of 1976-77. Some of the studies included are: (1) high-level and long-lived wastes, and (2) release and burial of low-level wastes. A list of 42 references is also presented. (HM)

  7. From Vegetable Waste to New Agents for Potential Health Applications: Antioxidant Properties and Effects of Extracts, Fractions and Pinocembrin from Glycyrrhiza glabra L. Aerial Parts on Viability of Five Human Cancer Cell Lines.

    Science.gov (United States)

    Aiello, Francesca; Armentano, Biagio; Polerà, Nicoletta; Carullo, Gabriele; Loizzo, Monica Rosa; Bonesi, Marco; Cappello, Maria Stella; Capobianco, Loredana; Tundis, Rosa

    2017-09-13

    Glycyrrhiza glabra cultivation and harvesting produces substantial quantities of aerial parts as waste. With the aim to prospect an innovative valorization of these byproducts, the aerial parts were harvested in May and October and analyzed for their chemical profile, antioxidant properties, and effects on viability of five cancer cell lines. Pinocembrin was the main constituent. A significant protection of lipid peroxidation was observed with the May total extract (IC50 of 4.2 ± 0.4 μg/mL at 30 min of incubation). The effects on viability of HeLa, MCF-7, MDA-MB-231, Caco-2, and PC3 human cancer cells were investigated. All samples shown a remarkable activity with IC50 values below 25 μg/mL. Samples from plants harvested in May exhibited greater activity than those harvested in October. MCF-7 and HeLa were the most sensitive cells with IC50 in the range 2.73-3.01 and 3.28-5.53 μg/mL, respectively. G. glabra aerial parts represent a good source of valuable products.

  8. Pollution profiles, health risk of VOCs and biohazards emitted from municipal solid waste transfer station and elimination by an integrated biological-photocatalytic flow system: a pilot-scale investigation.

    Science.gov (United States)

    Li, Guiying; Zhang, Zhengyong; Sun, Hongwei; Chen, Jiangyao; An, Taicheng; Li, Bing

    2013-04-15

    Volatile organic compounds (VOCs) and biohazards air pollution in municipal solid waste transfer station were investigated. As compressor working, the concentrations of almost all quantified 14 VOCs (0.32-306.03 μg m(-3)) were much higher than those as compressor off (0-13.31 μg m(-3)). Comparatively, only 3 VOCs with extremely low concentrations could be detected at control area. Total microorganism was 7567 CFU m(-3) as compressor working, which was 1.14 and 6.22 times higher than that of compressor off and control area, respectively. Bacteria were the most abundant microorganism at all three sampling places. At pilot-scale, during whole 60-day treatment, for VOCs, the average removal efficiencies were over 92% after biotrickling filter-photocatalytic (BTF-PC) treatment. Although non-cancer and cancer risks of some VOCs were over the concern level before treatment, almost all VOCs were removed substantially and both potential risks were below the concern after BTF-PC treatment. Additionally, biohazard concentrations decreased dramatically and air quality was purified from polluted to cleanness after PC treatment. All results demonstrated that the integrated technology possessed high removal capacity and long stability for the removal of VOCs and biohazards at a pilot scale. Copyright © 2013 Elsevier B.V. All rights reserved.

  9. Solid Waste Management Facilities with Permits by the Iowa DNR

    Data.gov (United States)

    Iowa State University GIS Support and Research Facility — All types of facilities that handle solid waste, including: sanitary landfills, appliance demanufacturing facilities, transfer stations, land application sites,...

  10. Solid Waste Land Applications with Permits by the Iowa DNR

    Data.gov (United States)

    Iowa State University GIS Support and Research Facility — All types of facilities that handle solid waste, including: sanitary landfills, appliance demanufacturing facilities, transfer stations, land application sites,...

  11. Energy Transfer with Hydrogen and Superconductivity - The Review of the First Experimental Results

    Science.gov (United States)

    Vysotsky, V. S.; Antyukhov, I. V.; Firsov, V. P.; Blagov, E. V.; Kostyuk, V. V.; Nosov, A. A.; Fetisov, S. S.; Zanegin, S. Yu.; Rachuk, V. S.; Katorgin, B. I.

    The transfer of massive amounts of both electrical and chemical power over long distances will present a major challenge for the global energy enterprise in future. Attraction of hydrogen is apparent as a chemical energy agent, possessing among the highest energy density content of various common fuels, whose combustive "waste" is simply water. The usage of "gratis" cold to cool a superconducting cable made of proper superconductor permits to deliver extra electrical power with the same line. This, rather old theoretical idea recently found its experimental realization. The team of Russian institutes and organizations with using Italian-produced MgB2 wire has made and successfully tested two hybrid energy transfer lines with liquid hydrogen as a chemical source of power and superconducting cable as a source of electricity. The first line has been tested in 2011. It has length ∼10 m, maximum liquid hydrogen flow ∼250 g/s and maximum current of MgB2 superconducting cable 2600 A @ 20K. This test was the first experimental proof of conception of the hybrid energy transfer line. The second line has been tested in October 2013. It has length ∼30 m. The new MgB2 cable has critical current at 21 K ∼3500 A and successfully passed high voltage DC test of 50 kV. New hydrogen cryostat has three sections with different types of thermal insulation in each section. The idea of hybrid energy transfer is formulated and details of first experiments are reviewed.

  12. Safety equipment list for 241-C-106 waste retrieval, Project W-320: Revision 1

    Energy Technology Data Exchange (ETDEWEB)

    Conner, J.C.

    1994-11-15

    The goals of the C-106 sluicing operation are: (1) to stabilize the tank by reducing the heat load in the tank to less than 42 MJ/hr (40,000 Btu/hour), and (2) to initiate demonstration of single-shell tank (SST) retrieval technology. The purpose of this supporting document (SD) is as follows: (1) to provide safety classifications for items (systems, structures, equipment, components, or parts) for the waste retrieval sluicing system (WRSS), and (2) to document and methodology used to develop safety classifications. Appropriate references are made with regard to use of existing systems, structures, equipments, components, and parts for C-106 single-shell transfer tank located in the C Tank Farm, and 241-AY-102 (AY-102) double shell receiver tanks (DST) located in the Aging Waste Facility (AWF). The Waste Retrieval Sluicing System consists of two transfer lines that would connect the two tanks, one to carry the sluiced waste slurry to AY-102, and the other to return the supernatant liquid to C-106. The supernatant, or alternate fluid, will be used to mobilize waste in C-106 for the sluicing process. The equipment necessary for the WRSS include pumps in each tank, sluicers to direct the supernatant stream in C-106, a slurry distributor in AY-102, HVAC for C-106, instrumentation and control devices, and other existing components as required.

  13. Preoperational test report, cross-site transfer system integrated test (POTR-007)

    Energy Technology Data Exchange (ETDEWEB)

    Pacquet, E.A.

    1998-04-02

    This report documents the results obtained during the performance of Preoperational Test POTP-007, from December 12, 1997 to March 27, 1998. The main objectives were to demonstrate the operation of the following Cross-Site Transfer System components: Booster pumps P-3125A and P-3125B interlocks and controls, both local and remote; Booster pump P-3125A and P-3125B and associated variable speed drives VSD-1 and VSD-2 performance in both manual and automatic modes; and Water filling, circulation, venting and draining of the transfer headers (supernate and slurry line). As described in reference 1, the following components of the Cross-Site Transfer System that would normally be used during an actual waste transfer, are not used in this specific test: Water Flush System; Valving and instrumentation associated with the 241-SY-A valve pit jumpers; and Valving and instrumentation associated with the 244-A lift station.

  14. Agricultural Waste.

    Science.gov (United States)

    Xue, Ling; Zhang, Panpan; Shu, Huajie; Chang, Chein-Chi; Wang, Renqing; Zhang, Shuping

    2016-10-01

    In recent years, the quantity of agricultural waste has been rising rapidly all over the world. As a result, the environmental problems and negative impacts of agricultural waste are drawn more and more attention. Therefore, there is a need to adopt proper approaches to reduce and reuse agricultural waste. This review presented about 200 literatures published in 2015 relating to the topic of agricultural waste. The review examined research on agricultural waste in 2015 from the following four aspects: the characterization, reuse, treatment, and management. Researchers highlighted the importance to reuse agricultural waste and investigated the potential to utilize it as biofertilizers, cultivation material, soil amendments, adsorbent, material, energy recycling, enzyme and catalyst etc. The treatment of agricultural waste included carbonization, biodegradation, composting hydrolysis and pyrolysis. Moreover, this review analyzed the differences of the research progress in 2015 from 2014. It may help to reveal the new findings and new trends in this field in 2015 comparing to 2014.

  15. Generation, storage, collection and transportation of municipal solid waste--a case study in the city of Kathmandu, capital of Nepal.

    Science.gov (United States)

    Alam, R; Chowdhury, M A I; Hasan, G M J; Karanjit, B; Shrestha, L R

    2008-01-01

    Solid waste management (SWM) services have consistently failed to keep up with the vast amount of solid waste produced in urban areas. There is not currently an efficient system in place for the management, storage, collection, and transportation of solid waste. Kathmandu City, an important urban center of South Asia, is no exception. In Kathmandu Metropolitan City, solid waste generation is predicted to be 1091 m(3)/d (245 tons/day) and 1155 m(3)/d (260 tons/day) for the years 2005 and 2006, respectively. The majority (89%) of households in Kathmandu Metropolitan City are willing to segregate the organic and non-organic portions of their waste. Overall collection efficiency was 94% in 2003. An increase in waste collection occurred due to private sector involvement, the shutdown of the second transfer station near the airport due to local protest, a lack of funding to maintain trucks/equipment, a huge increase in plastic waste, and the willingness of people to separate their waste into separate bins. Despite a substantial increase in total expenditure, no additional investments were made to the existing development plan to introduce a modern disposal system due to insufficient funding. Due to the lack of a proper lining, raw solid waste from the existing dumping site comes in contact with river water directly, causing severe river contamination and deteriorating the quality of the water.

  16. Development, validation and transfer of a near infrared method to determine in-line the end point of a fluidised drying process for commercial production batches of an approved oral solid dose pharmaceutical product.

    Science.gov (United States)

    Peinado, Antonio; Hammond, Jonathan; Scott, Andrew

    2011-01-05

    Pharmaceutical companies are progressively adopting and introducing the principles of Quality by Design with the main purpose of assurance and built-in quality throughout the whole manufacturing process. Within this framework, a Partial Least Square (PLS) model, based on Near Infrared (NIR) spectra and humidity determinations, was built in order to determine in-line the drying end point of a fluidized bed process. The in-process method was successfully validated following the principles described within The International Conference on Harmonization of Technical Requirements for Registration of Pharmaceuticals for Human Use - ICH Q2 (r1) - Validation of Analytical Procedures: Text and Methodology. However, in some aspects, the cited guidelines were not appropriate to in-process methods developed and validated exclusively with in-line samples and implemented in dynamic systems, such as drying processes. In this work, a customized interpretation of guidelines has been adopted which provided the framework of evidence to support a validated application. The application has been submitted to the United States Food and Drug Administration (FDA) and The European Medicines Agency (EMA) during applications for grant of licences. Representatives from these Regulatory Authorities have specifically reviewed this novel application during on-site inspections, and have subsequently approved both the product and this application. Currently, the NIR method is implemented as a primary in-line method to control the drying end point in real-time (to below a control limit of not greater than 1.2% w/w) for commercial production batches of an approved, solid, oral-dose medicine. The implementation of this in-process method allows real-time control with benefits including a reduction in operation time and labour; sample handling and waste generation; and a reduced risk to product quality in further unit operations due to improved consistency of intermediate output at this stage. To date

  17. Nevada National Security Site Waste Acceptance Criteria

    Energy Technology Data Exchange (ETDEWEB)

    NSTec Environmental Management

    2011-01-01

    This document establishes the U.S. Department of Energy, National Nuclear Security Administration Nevada Site Office (NNSA/NSO) Nevada National Security Site Waste Acceptance Criteria (NNSSWAC). The NNSSWAC provides the requirements, terms, and conditions under which the Nevada National Security Site (NNSS) will accept low-level radioactive waste and mixed low-level waste for disposal. The NNSSWAC includes requirements for the generator waste certification program, characterization, traceability, waste form, packaging, and transfer. The criteria apply to radioactive waste received at the NNSS Area 3 and Area 5 Radioactive Waste Management Complex for disposal. The NNSA/NSO and support contractors are available to assist you in understanding or interpreting this document. For assistance, please call the NNSA/NSO Waste Management Project at (702) 295-7063 or fax to (702) 295-1153.

  18. Nevada National Security Site Waste Acceptance Criteria

    Energy Technology Data Exchange (ETDEWEB)

    NSTec Environmental Management

    2010-09-03

    This document establishes the U.S. Department of Energy, National Nuclear Security Administration Nevada Site Office (NNSA/NSO) Nevada National Security Site Waste Acceptance Criteria (NNSSWAC). The NNSSWAC provides the requirements, terms, and conditions under which the Nevada National Security Site (NNSS) will accept low-level radioactive waste and mixed low-level waste for disposal. The NNSSWAC includes requirements for the generator waste certification program, characterization, traceability, waste form, packaging, and transfer. The criteria apply to radioactive waste received at the NNSS Area 3 and Area 5 Radioactive Waste Management Complex for disposal. The NNSA/NSO and support contractors are available to assist you in understanding or interpreting this document. For assistance, please call the NNSA/NSO Waste Management Project at (702) 295-7063 or fax to (702) 295-1153.

  19. Ariane transfer vehicle scenario

    Science.gov (United States)

    Deutscher, Norbert; Cougnet, Claude

    1990-10-01

    ESA's Ariane Transfer Vehicle (ATV) is a vehicle design concept for the transfer of payloads from Ariane 5 launch vehicle orbit insertion to a space station, on the basis of the Ariane 5 program-developed Upper Stage Propulsion Module and Vehicle Equipment Bay. The ATV is conceived as a complement to the Hermes manned vehicle for lower cost unmanned carriage of logistics modules and other large structural elements, as well as waste disposal. It is also anticipated that the ATV will have an essential role in the building block transportation logistics of any prospective European space station.

  20. Plasma vitrification of waste materials

    Science.gov (United States)

    McLaughlin, David F.; Dighe, Shyam V.; Gass, William R.

    1997-01-01

    This invention provides a process wherein hazardous or radioactive wastes in the form of liquids, slurries, or finely divided solids are mixed with finely divided glassformers (silica, alumina, soda, etc.) and injected directly into the plume of a non-transferred arc plasma torch. The extremely high temperatures and heat transfer rates makes it possible to convert the waste-glassformer mixture into a fully vitrified molten glass product in a matter of milliseconds. The molten product may then be collected in a crucible for casting into final wasteform geometry, quenching in water, or further holding time to improve homogeneity and eliminate bubbles.

  1. Stochastic Consequence Analysis for Waste Leaks

    Energy Technology Data Exchange (ETDEWEB)

    HEY, B.E.

    2000-05-31

    This analysis evaluates the radiological consequences of potential Hanford Tank Farm waste transfer leaks. These include ex-tank leaks into structures, underneath the soil, and exposed to the atmosphere. It also includes potential misroutes, tank overflow

  2. Using MERRA-2 analysis fields to simulate limb scattered radiance profiles for inhomogeneous atmospheric lines of sight: Preparation for data assimilation of OMPS LP radiances through 2D single-scattering GSLS radiative transfer model development

    Science.gov (United States)

    Loughman, R. P.; Bhartia, P. K.; Moy, L.; Kramarova, N. A.; Wargan, K.

    2016-12-01

    Many remote sensing techniques used to monitor the Earth's upper atmosphere fall into the broad category of "limb viewing" (LV) measurements, which includes any method for which the line of sight (LOS) fails to intersect the surface. Occultation, limb emission and limb scattering (LS) measurements are all LV methods that offer strong sensitivity to changes in the atmosphere near the tangent point of the LOS, due to the enhanced geometric path through the tangent layer (where the concentration also typically peaks, for most atmospheric species). But many of the retrieval algorithms used to interpret LV measurements assume that the atmosphere consists of "spherical shells", in which the atmospheric properties vary only with altitude (creating a 1D atmosphere). This assumption simplifies the analysis, but at the possible price of misinterpreting measurements made in the real atmosphere. In this presentation, we focus on the problem of LOS inhomogeneity for LS measurements made by the OMPS Limb Profiler (LP) instrument during the 2015 ozone hole period. The GSLS radiative transfer model (RTM) used in the default OMPS LP algorithms assumes a spherical-shell atmosphere defined at levels spaced 1 km apart, with extinction coefficients assumed to vary linearly with height between levels. Several recent improvements enable an updated single-scattering version of the GSLS RTM to ingest 3D MERRA-2 analysis fields (including temperature, pressure, and ozone concentration) when creating the model atmosphere, by introducing flexible altitude grids, flexible atmospheric specification along the LOS, and improved treatment of the radiative transfer within each atmospheric layer. As a result, the effect of LOS inhomogeneity on the current (1D) OMPS LP retrieval algorithm can now be studied theoretically, using realistic 3D atmospheric profiles. This work also represents a step towards enabling OMPS LP data to be ingested as part of future data assimilation efforts.

  3. Industrial Waste

    DEFF Research Database (Denmark)

    Christensen, Thomas Højlund

    2011-01-01

    Industrial waste is waste from industrial production and manufacturing. Industry covers many industrial sectors and within each sector large variations are found in terms of which raw materials are used, which production technology is used and which products are produced. Available data on unit...... generation rates and material composition as well as determining factors are discussed in this chapter. Characterizing industrial waste is faced with the problem that often only a part of the waste is handled in the municipal waste system, where information is easily accessible. In addition part...... of the industrial waste may in periods, depending on market opportunities and prices, be traded as secondary rawmaterials. Production-specificwaste from primary production, for example steel slag, is not included in the current presentation. In some countries industries must be approved or licensed and as part...

  4. Hanford Site Transuranic (TRU) Waste Certification Plan

    Energy Technology Data Exchange (ETDEWEB)

    GREAGER, T.M.

    2000-12-01

    As a generator of transuranic (TRU) and TRU mixed waste destined for disposal at the Waste Isolation Pilot Plant (WIPP), the Hanford Site must ensure that its TRU waste meets the requirements of US. Department of Energy (DOE) 0 435.1, ''Radioactive Waste Management,'' and the Contact-Handled (CH) Transuranic Waste Acceptance Criteria for the Waste Isolation Pilot Plant (WIPP-WAC). WIPP-WAC requirements are derived from the WIPP Technical Safety Requirements, WIPP Safety Analysis Report, TRUPACT-II SARP, WIPP Land Withdrawal Act, WIPP Hazardous Waste Facility Permit, and Title 40 Code of Federal Regulations (CFR) 191/194 Compliance Certification Decision. The WIPP-WAC establishes the specific physical, chemical, radiological, and packaging criteria for acceptance of defense TRU waste shipments at WIPP. The WPP-WAC also requires that participating DOE TRU waste generator/treatment/storage sites produce site-specific documents, including a certification plan, that describe their program for managing TRU waste and TRU waste shipments before transferring waste to WIPP. Waste characterization activities provide much of the data upon which certification decisions are based. Waste characterization requirements for TRU waste and TRU mixed waste that contains constituents regulated under the Resource Conservation and Recovery Act (RCRA) are established in the WIPP Hazardous Waste Facility Permit Waste Analysis Plan (WAP). The Hanford Site Quality Assurance Project Plan (QAPjP) (HNF-2599) implements the applicable requirements in the WAP and includes the qualitative and quantitative criteria for making hazardous waste determinations. The Hanford Site must also ensure that its TRU waste destined for disposal at WPP meets requirements for transport in the Transuranic Package Transporter-11 (TRUPACT-11). The US. Nuclear Regulatory Commission (NRC) establishes the TRUPACT-11 requirements in the Safety Analysis Report for the TRUPACT-II Shipping Package

  5. Hanford Site Transuranic (TRU) Waste Certification Plan

    Energy Technology Data Exchange (ETDEWEB)

    GREAGER, T.M.

    2000-12-06

    As a generator of transuranic (TRU) and TRU mixed waste destined for disposal at the Waste Isolation Pilot Plant (WIPP), the Hanford Site must ensure that its TRU waste meets the requirements of US. Department of Energy (DOE) 0 435.1, ''Radioactive Waste Management,'' and the Contact-Handled (CH) Transuranic Waste Acceptance Criteria for the Waste Isolation Pilot Plant (WIPP-WAC). WIPP-WAC requirements are derived from the WIPP Technical Safety Requirements, WIPP Safety Analysis Report, TRUPACT-II SARP, WIPP Land Withdrawal Act, WIPP Hazardous Waste Facility Permit, and Title 40 Code of Federal Regulations (CFR) 191/194 Compliance Certification Decision. The WIPP-WAC establishes the specific physical, chemical, radiological, and packaging criteria for acceptance of defense TRU waste shipments at WIPP. The WPP-WAC also requires that participating DOE TRU waste generator/treatment/storage sites produce site-specific documents, including a certification plan, that describe their program for managing TRU waste and TRU waste shipments before transferring waste to WIPP. Waste characterization activities provide much of the data upon which certification decisions are based. Waste characterization requirements for TRU waste and TRU mixed waste that contains constituents regulated under the Resource Conservation and Recovery Act (RCRA) are established in the WIPP Hazardous Waste Facility Permit Waste Analysis Plan (WAP). The Hanford Site Quality Assurance Project Plan (QAPjP) (HNF-2599) implements the applicable requirements in the WAP and includes the qualitative and quantitative criteria for making hazardous waste determinations. The Hanford Site must also ensure that its TRU waste destined for disposal at WPP meets requirements for transport in the Transuranic Package Transporter-11 (TRUPACT-11). The US. Nuclear Regulatory Commission (NRC) establishes the TRUPACT-11 requirements in the Safety Analysis Report for the TRUPACT-II Shipping Package

  6. Waste indicators

    Energy Technology Data Exchange (ETDEWEB)

    Dall, O.; Lassen, C.; Hansen, E. [Cowi A/S, Lyngby (Denmark)

    2003-07-01

    The Waste Indicator Project focuses on methods to evaluate the efficiency of waste management. The project proposes the use of three indicators for resource consumption, primary energy and landfill requirements, based on the life-cycle principles applied in the EDIP Project. Trial runs are made With the indicators on paper, glass packaging and aluminium, and two models are identified for mapping the Danish waste management, of which the least extensive focuses on real and potential savings. (au)

  7. Comparison of Waste Feed Delivery Small Scale Mixing Demonstration Simulant to Hanford Waste

    Energy Technology Data Exchange (ETDEWEB)

    Wells, Beric E.; Gauglitz, Phillip A.; Rector, David R.

    2012-07-10

    The Hanford double-shell tank (DST) system provides the staging location for waste that will be transferred to the Hanford Tank Waste Treatment and Immobilization Plant (WTP). Specific WTP acceptance criteria for waste feed delivery describe the physical and chemical characteristics of the waste that must be met before the waste is transferred from the DSTs to the WTP. One of the more challenging requirements relates to the sampling and characterization of the undissolved solids (UDS) in a waste feed DST because the waste contains solid particles that settle and their concentration and relative proportion can change during the transfer of the waste in individual batches. A key uncertainty in the waste feed delivery system is the potential variation in UDS transferred in individual batches in comparison to an initial sample used for evaluating the acceptance criteria. To address this uncertainty, a number of small-scale mixing tests have been conducted as part of Washington River Protection Solutions' Small Scale Mixing Demonstration (SSMD) project to determine the performance of the DST mixing and sampling systems. A series of these tests have used a five-part simulant composed of particles of different size and density and designed to be equal or more challenging than AY-102 waste. This five-part simulant, however, has not been compared with the broad range of Hanford waste, and thus there is an additional uncertainty that this simulant may not be as challenging as the most difficult Hanford waste. The purpose of this study is to quantify how the current five-part simulant compares to all of the Hanford sludge waste, and to suggest alternate simulants that could be tested to reduce the uncertainty in applying the current testing results to potentially more challenging wastes.

  8. Comparison of Waste Feed Delivery Small Scale Mixing Demonstration Simulant to Hanford Waste

    Energy Technology Data Exchange (ETDEWEB)

    Wells, Beric E.; Gauglitz, Phillip A.; Rector, David R.

    2011-09-01

    The Hanford double-shell tank (DST) system provides the staging location for waste that will be transferred to the Hanford Tank Waste Treatment and Immobilization Plant (WTP). Specific WTP acceptance criteria for waste feed delivery describe the physical and chemical characteristics of the waste that must be met before the waste is transferred from the DSTs to the WTP. One of the more challenging requirements relates to the sampling and characterization of the undissolved solids (UDS) in a waste feed DST because the waste contains solid particles that settle and their concentration and relative proportion can change during the transfer of the waste in individual batches. A key uncertainty in the waste feed delivery system is the potential variation in UDS transferred in individual batches in comparison to an initial sample used for evaluating the acceptance criteria. To address this uncertainty, a number of small-scale mixing tests have been conducted as part of Washington River Protection Solutions' Small Scale Mixing Demonstration (SSMD) project to determine the performance of the DST mixing and sampling systems. A series of these tests have used a five-part simulant composed of particles of different size and density and designed to be equal or more challenging than AY-102 waste. This five-part simulant, however, has not been compared with the broad range of Hanford waste, and thus there is an additional uncertainty that this simulant may not be as challenging as the most difficult Hanford waste. The purpose of this study is to quantify how the current five-part simulant compares to all of the Hanford sludge waste, and to suggest alternate simulants that could be tested to reduce the uncertainty in applying the current testing results to potentially more challenging wastes.

  9. Storing Waste in Ceramic

    Energy Technology Data Exchange (ETDEWEB)

    Bourcier, W L; Sickafus, K

    2004-07-20

    Not all the nuclear waste destined for Yucca Mountain is in the form of spent fuel. Some of it will be radioactive waste generated from the production of nuclear weapons. This so-called defense waste exists mainly as corrosive liquids and sludge in underground tanks. An essential task of the U.S. high-level radioactive waste program is to process these defense wastes into a solid material--called a waste form. An ideal waste form would be extremely durable and unreactive with other repository materials. It would be simple to fabricate remotely so that it could be safely transported to a repository for permanent storage. What's more, the material should be able to tolerate exposure to intense radiation without degradation. And to minimize waste volume, the material must be able to contain high concentrations of radionuclides. The material most likely to be used for immobilization of radioactive waste is glass. Glasses are produced by rapid cooling of high-temperature liquids such that the liquid-like non-periodic structure is preserved at lower temperatures. This rapid cooling does not allow enough time for thermodynamically stable crystalline phases (mineral species) to form. In spite of their thermodynamic instability, glasses can persist for millions of years. An alternate to glass is a ceramic waste form--an assemblage of mineral-like crystalline solids that incorporate radionuclides into their structures. The crystalline phases are thermodynamically stable at the temperature of their synthesis; ceramics therefore tend to be more durable than glasses. Ceramic waste forms are fabricated at temperatures below their melting points and so avoid the danger of handling molten radioactive liquid--a danger that exists with incorporation of waste in glasses. The waste form provides a repository's first line of defense against release of radionuclides. It, along with the canister, is the barrier in the repository over which we have the most control. When a waste

  10. Landfilling of waste

    Energy Technology Data Exchange (ETDEWEB)

    Christensen, T.H.; Cossu, R.; Stegmann, R. (eds.)

    1994-01-01

    In view of the great demand for information regarding landfills, a series of international reference books on landfilling of waste has been established. This book, the second volume, deals with lining and leachate collection. It consists of edited, selected contributions to the International Symposia on Sanitary Landfills held in Sardinia every second year. Topics of discussion include: lining systems; design and construction; properties and quality control of clay materials; properties and quality control of synthetic materials; geotextiles and geogrids, and leachate drainage and collection.

  11. Secondary Waste Form Down-Selection Data Package—Fluidized Bed Steam Reforming Waste Form

    Energy Technology Data Exchange (ETDEWEB)

    Qafoku, Nikolla; Westsik, Joseph H.; Strachan, Denis M.; Valenta, Michelle M.; Pires, Richard P.

    2011-09-12

    The Hanford Site in southeast Washington State has 56 million gallons of radioactive and chemically hazardous wastes stored in 177 underground tanks (ORP 2010). The U.S. Department of Energy (DOE), Office of River Protection (ORP), through its contractors, is constructing the Hanford Tank Waste Treatment and Immobilization Plant (WTP) to convert the radioactive and hazardous wastes into stable glass waste forms for disposal. Within the WTP, the pretreatment facility will receive the retrieved waste from the tank farms and separate it into two treated process streams. These waste streams will be vitrified, and the resulting waste canisters will be sent to offsite (high-level waste [HLW]) and onsite (immobilized low-activity waste [ILAW]) repositories. As part of the pretreatment and ILAW processing, liquid secondary wastes will be generated that will be transferred to the Effluent Treatment Facility (ETF) on the Hanford Site for further treatment. These liquid secondary wastes will be converted to stable solid waste forms that will be disposed of in the Integrated Disposal Facility (IDF). To support the selection of a waste form for the liquid secondary wastes from WTP, Washington River Protection Solutions (WRPS) has initiated secondary waste form testing work at Pacific Northwest National Laboratory (PNNL). In anticipation of a down-selection process for a waste form for the Solidification Treatment Unit to be added to the ETF, PNNL is developing data packages to support that down-selection. The objective of the data packages is to identify, evaluate, and summarize the existing information on the four waste forms being considered for stabilizing and solidifying the liquid secondary wastes. At the Hanford Site, the FBSR process is being evaluated as a supplemental technology for treating and immobilizing Hanford LAW radioactive tank waste and for treating secondary wastes from the WTP pretreatment and LAW vitrification processes.

  12. On-site profiling and speciation of polycyclic aromatic hydrocarbons at manufactured gas plant sites by a high temperature transfer line, membrane inlet probe coupled to a photoionization detector and gas chromatograph/mass spectrometer.

    Science.gov (United States)

    Considine, Thomas; Robbat, Albert

    2008-02-15

    A new high temperature transfer line, membrane inlet probe (HTTL-MIP) coupled to a photoionization detector (PID) and gas chromatograph/mass spectrometer (GC/MS) was used to rapidly profile and speciate polycyclic aromatic hydrocarbons (PAH) in the subsurface. PID signals were in agreement with GC/MS results. Correlation coefficients of 0.92 and 0.99 were obtained for discrete and composite samples collected from the same exact location. Continuous probe advancement with PID detection found coal tar, a dense nonaqueous phase liquid, in soil channels and saturated media. When samples were collected conventionally, split, solvent extracted, and analyzed in the field and confirmation laboratory, GC/MS measurement precision and accuracy were indistinguishable; despite the fact the field laboratory produced data five times faster than the laboratory using standard EPA methods. No false positive/negatives were found. Based on these findings, increased confidence in site conceptual models should be obtained, since PID response indicated total PAH presence/absence in "real-time", while GC/MS provided information as to which PAH was present and atwhat concentration. Incorporation of this tool into a dynamic workplan will provide more data at less cost enabling environmental scientists, engineers, and regulators to better understand coal tar migration and its impact on human health and the environment.

  13. Case study: Is the 'catch-all-plastics bin' useful in unlocking the hidden resource potential in the residual waste collection system?

    Science.gov (United States)

    Kranzinger, Lukas; Schopf, Kerstin; Pomberger, Roland; Punesch, Elisabeth

    2017-02-01

    Austria's performance in the collection of separated waste is adequate. However, the residual waste still contains substantial amounts of recyclable materials - for example, plastics, paper and board, glass and composite packaging. Plastics (lightweight packaging and similar non-packaging materials) are detected at an average mass content of 13% in residual waste. Despite this huge potential, only 3% of the total amount of residual waste (1,687,000 t y -1 ) is recycled. This implies that most of the recyclable materials contained in the residual waste are destined for thermal recovery and are lost for recycling. This pilot project, commissioned by the Land of Lower Austria, applied a holistic approach, unique in Europe, to the Lower Austrian waste management system. It aims to transfer excess quantities of plastic packaging and non-packaging recyclables from the residual waste system to the separately collected waste system by introducing a so-called 'catch-all-plastics bin'. A quantity flow model was constructed and the results showed a realistic increase in the amount of plastics collected of 33.9 wt%. This equals a calculated excess quantity of 19,638 t y -1 . The increased plastics collection resulted in a positive impact on the climate footprint (CO 2 equivalent) in line with the targets of EU Directive 94/62/EG (Circular Economy Package) and its Amendments. The new collection system involves only moderate additional costs.

  14. Optimization of municipal solid waste collection and transportation routes

    Energy Technology Data Exchange (ETDEWEB)

    Das, Swapan, E-mail: swapan2009sajal@gmail.com; Bhattacharyya, Bidyut Kr., E-mail: bidyut53@yahoo.co.in

    2015-09-15

    Graphical abstract: Display Omitted - Highlights: • Profitable integrated solid waste management system. • Optimal municipal waste collection scheme between the sources and waste collection centres. • Optimal path calculation between waste collection centres and transfer stations. • Optimal waste routing between the transfer stations and processing plants. - Abstract: Optimization of municipal solid waste (MSW) collection and transportation through source separation becomes one of the major concerns in the MSW management system design, due to the fact that the existing MSW management systems suffer by the high collection and transportation cost. Generally, in a city different waste sources scatter throughout the city in heterogeneous way that increase waste collection and transportation cost in the waste management system. Therefore, a shortest waste collection and transportation strategy can effectively reduce waste collection and transportation cost. In this paper, we propose an optimal MSW collection and transportation scheme that focus on the problem of minimizing the length of each waste collection and transportation route. We first formulize the MSW collection and transportation problem into a mixed integer program. Moreover, we propose a heuristic solution for the waste collection and transportation problem that can provide an optimal way for waste collection and transportation. Extensive simulations and real testbed results show that the proposed solution can significantly improve the MSW performance. Results show that the proposed scheme is able to reduce more than 30% of the total waste collection path length.

  15. MECHANISMS GOVERNING TRANSIENTS FROM THE BATCH INCINERATION OF LIQUID WASTES IN ROTARY KILNS

    Science.gov (United States)

    When "containerized" liquid wastes, bound on sorbents. are introduced into a rotary kiln in a batch mode, transient phenomena in-volving heat transfer into, and waste mass transfer out of, the sorbent can oromote the raoid release of waste vaoor into the kiln environment. This ra...

  16. Low-level waste feed staging plan

    Energy Technology Data Exchange (ETDEWEB)

    Certa, P.J.; Grams, W.H.; McConville, C.M.; L. W. Shelton, L.W.; Slaathaug, E.J., Westinghouse Hanford

    1996-08-12

    The `Preliminary Low-Level Waste Feed Staging Plan` was updated to reflect the latest requirement in the Tank Waste Remediation Privatization Request for Proposals (RFP) and amendments. The updated plan develops the sequence and transfer schedule for retrieval of DST supernate by the management and integration contractor and delivery of the staged supernate to the private low-activity waste contractors for treatment. Two DSTs are allocated as intermediate staging tanks. A transfer system conflict analysis provides part of the basis for determining transfer system upgrade requirements to support both low-activity and high-level waste feed delivery. The intermediate staging tank architecture and retrieval system equipment are provided as a planning basis until design requirements documents are prepared. The actions needed to successfully implement the plan are identified. These include resolution of safety issues and changes to the feed envelope limits, minimum order quantities, and desired batch sizes.

  17. DM100 AND DM1200 MELTER TESTING WITH HIGH WASTE LOADING GLASS FORMULATIONS FOR HANFORD HIGH-ALUMINUM HLW STREAMS

    Energy Technology Data Exchange (ETDEWEB)

    KRUGER AA; MATLACK KS; KOT WK; PEGG IL; JOSEPH I

    2009-12-30

    transfer and glass melting rate. The WTP HLW melter has a glass surface area of 3.75 m{sup 2} and depth of {approx}1.1 m. The two melters in the HLW facility together are designed to produce up to 7.5 MT of glass per day at 100% availability. Further increases in HLW waste processing rates can potentially be achieved by increasing the melter operating temperature above 1150 C and by increasing the waste loading in the glass product Increasing the waste loading also has the added benefit of decreasing the number of canisters for storage. The current estimates and glass formulation efforts have been conservative in terms of achievable waste loadings. These formulations have been specified to ensure that the glasses are homogenous, contain essentially no crystalline phases, are processable in joule-heated, ceramic-lined melters and meet WTP contract requirements. The WTP's overall mission will require the immobilization oftank waste compositions that are dominated by mixtures of aluminum (Al), chromium (Cr), bismuth (Bi), iron (Fe), phosphorous (P), zirconium (Zr), and sulfur (S) compounds as waste-limiting components. Glass compositions for these waste mixtures have been developed based upon previous experience and current glass property models. Recently, DOE has initiated a testing program to develop and characterize HLW glasses with higher waste loadings. Results of this work have demonstrated the feasibility of increases in waste-loading from about 25 wt% to 33-50 wt% (based on oxide loading) in the glass depending on the waste stream. It is expected that these higher waste loading glasses will reduce the HLW canister production requirement by about 25% or more.

  18. Waste Facilities

    Data.gov (United States)

    Vermont Center for Geographic Information — This dataset was developed from the Vermont DEC's list of certified solid waste facilities. It includes facility name, contact information, and the materials...

  19. NEVADA TEST SITE WASTE ACCEPTANCE CRITERIA, JUNE 2006

    Energy Technology Data Exchange (ETDEWEB)

    U.S. DEPARTMENT OF ENERGY, NATIONAL NUCLEAR SECURITY ADMINISTRATION NEVADA SITE OFFICE

    2006-06-01

    This document establishes the U.S. Department of Energy (DOE), National Nuclear Security Administration Nevada Site Office (NNSA/NSO) waste acceptance criteria (WAC). The WAC provides the requirements, terms, and conditions under which the Nevada Test Site (NTS) will accept low-level radioactive (LLW) and mixed waste (MW) for disposal. It includes requirements for the generator waste certification program, characterization, traceability, waste form, packaging, and transfer. The criteria apply to radioactive waste received at the NTS Area 3 and Area 5 Radioactive Waste Management Complex (RWMC) for storage or disposal.

  20. Waste Management Program. Technical progress report, July-December, 1984

    Energy Technology Data Exchange (ETDEWEB)

    None

    1986-10-01

    This report provides information on operations and development programs for the management of radioactive wastes from operation of the Savannah River Plant and offplant participants. The studies on environmental and safety assessments, other support, in situ storage or disposal, waste form development and characterization, process and equipment development, and the Defense Waste Processing Facility are a part of the Long-Term Waste Management Technology Program. The following studies are reported for the SR Interim Waste Operations: tank farm operation, inspection program, burial ground operations, and waste transfer/tank replacement.

  1. Glass fabrication and analysis literature review and method selection for WTP waste feed qualification

    Energy Technology Data Exchange (ETDEWEB)

    Peeler, D. K. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

    2013-06-01

    The waste feed qualification program is being developed to protect the Hanford Tank Waste Treatment and Immobilization Plant (WTP) safety basis, technical basis, and design by assuring waste acceptance requirements are met for each staged waste feed Campaign prior to transfer from the Hanford Tank Farm to the WTP.

  2. Study of Material Flow of End-of-Life Computer Equipment (e-wastes ...

    African Journals Online (AJOL)

    makorede

    This delay or staggering in e-waste disposal would reduce the amount of e-waste disposed yearly and thus afford the country the time to make plans to accommodate and manage the e-wastes generated more efficiently. KEYWORDS: e-waste, material flow model, computer equipment, sensitivity analysis, transfer coefficient.

  3. Transfer Pricing

    DEFF Research Database (Denmark)

    Nielsen, Søren Bo

    2014-01-01

    Against a background of rather mixed evidence about transfer pricing practices in multinational enterprises (MNEs) and varying attitudes on the part of tax authorities, this paper explores how multiple aims in transfer pricing can be pursued across four different transfer pricing regimes. A MNE h...

  4. Computational investigation of fluid flow and heat transfer of an economizer by porous medium approach

    Science.gov (United States)

    Babu, C. Rajesh; Kumar, P.; Rajamohan, G.

    2017-07-01

    Computation of fluid flow and heat transfer in an economizer is simulated by a porous medium approach, with plain tubes having a horizontal in-line arrangement and cross flow arrangement in a coal-fired thermal power plant. The economizer is a thermal mechanical device that captures waste heat from the thermal exhaust flue gasses through heat transfer surfaces to preheat boiler feed water. In order to evaluate the fluid flow and heat transfer on tubes, a numerical analysis on heat transfer performance is carried out on an 110 t/h MCR (Maximum continuous rating) boiler unit. In this study, thermal performance is investigated using the computational fluid dynamics (CFD) simulation using ANSYS FLUENT. The fouling factor ε and the overall heat transfer coefficient ψ are employed to evaluate the fluid flow and heat transfer. The model demands significant computational details for geometric modeling, grid generation, and numerical calculations to evaluate the thermal performance of an economizer. The simulation results show that the overall heat transfer coefficient 37.76 W/(m2K) and economizer coil side pressure drop of 0.2 (kg/cm2) are found to be conformity within the tolerable limits when compared with existing industrial economizer data.

  5. Tribal Waste Management Program

    Science.gov (United States)

    The EPA’s Tribal Waste Management Program encourages environmentally sound waste management practices that promote resource conservation through recycling, recovery, reduction, clean up, and elimination of waste.

  6. Facilitating the improved management of waste in South Africa through a national waste information system.

    Science.gov (United States)

    Godfrey, Linda

    2008-01-01

    Developing a waste information system (WIS) for a country is more than just about collecting routine data on waste; it is about facilitating the improved management of waste by providing timely, reliable information to the relevant role-players. It is a means of supporting the waste governance challenges facing South Africa - challenges ranging from strategic waste management issues at national government to basic operational challenges at local government. The paper addresses two hypotheses. The first is that the identified needs of government can provide a platform from which to design a national WIS framework for a developing country such as South Africa, and the second is that the needs for waste information reflect greater, currently unfulfilled challenges in the sustainable management of waste. Through a participatory needs analysis process, it is shown that waste information is needed by the three spheres of government, to support amongst others, informed planning and decision-making, compliance monitoring and enforcement, community participation through public access to information, human, infrastructure and financial resource management and policy development. These needs for waste information correspond closely with key waste management challenges currently facing the country. A shift in governments approach to waste, in line with national and international policy, is evident from identified current and future waste information needs. However, the need for information on landfilling remains entrenched within government, possibly due to the poor compliance of landfill sites in South Africa and the problems around the illegal disposal of both general and hazardous waste.

  7. Waste Generation in Denmark 1994-2005

    DEFF Research Database (Denmark)

    Brix, Louise Lykke; Bentzen, Jan Børsen

    covering the time span 1994-2005 has been included. By means of the Log-Mean Divisia Index Method (LMDI) an algebraic decomposition of the data for the waste amounts generated is performed. This methodology separates the increases in waste amounts into effects related to economic activity, industrial......In recent years the amount of waste generated by Danish firms has increased significantly. In the present analysis we use the decomposition analysis, which has been widely used in the energy economics literature to explain the mechanisms influencing energy consumption and CO2 emissions....... In this paper the methodology is transferred to the topic of waste generation and is used to analyse why the amount of business waste is increasing. The empirical application is related to data for the volumes of waste generated in the Danish economy for the main sectors as well as the manufacturing sector...

  8. Instalaţie de condensare gaze exhaustate de la linia de presare feţe de uşi (HDF, cu recuperator de căldură şi colectare ape uzate/Condensing instalation for exhausted gas from door-skin pressing line (HDF with heat recovery and waste water collecting

    Directory of Open Access Journals (Sweden)

    Nicolae BĂDIN

    2016-12-01

    Full Text Available During the door-skin pressing (HDF, on the production facility are emitted an importing quantity of gases which have an substantial part of dust (small particles and another pollutant (formaldehyde, etc. Ordinary production line give all those gases in atmosphere but the newest prescription of European regulation (BAT try to reduce to the minimum (eliminate if it possible those emissions .In this ideas I present one solution for capture gases and use his energy for another purposes. In the same time, waste water with polluted material are collected separately and stored, used or eliminated with proper company.

  9. MELT RATE ENHANCEMENT FOR HIGH ALUMINUM HLW (HIGH LEVEL WASTE) GLASS FORMULATION FINAL REPORT 08R1360-1

    Energy Technology Data Exchange (ETDEWEB)

    KRUGER AA; MATLACK KS; KOT W; PEGG IL; JOSEPH I; BARDAKCI T; GAN H; GONG W; CHAUDHURI M

    2010-01-04

    . The WTP HLW melter design, unlike earlier DOE melter designs, incorporates an active glass bubbler system. The bubblers create active glass pool convection and thereby improve heat transfer and glass melting rate. The WTP HLW melter has a glass surface area of 3.75 m{sup 2} and depth of {approx}1.1 m. The two melters in the HLW facility together are designed to produce up to 7.5 MT of glass per day at 100% availability. Further increases in HLW waste processing rates can potentially be achieved by increasing the melter operating temperature above 1150 C and by increasing the waste loading in the glass product. Increasing the waste loading also has the added benefit of decreasing the number of canisters for storage. The current estimates and glass formulation efforts have been conservative in terms of achievable waste loadings. These formulations have been specified to ensure that the glasses are homogenous, contain essentially no crystalline phases, are processable in joule-heated, ceramic-lined melters and meet WTP Contract terms. The WTP's overall mission will require the immobilization of tank waste compositions that are dominated by mixtures of aluminum (Al), chromium (Cr), bismuth (Bi), iron (Fe), phosphorous (P), zirconium (Zr), and sulfur (S) compounds as waste-limiting components. Glass compositions for these waste mixtures have been developed based upon previous experience and current glass property models. Recently, DOE has initiated a testing program to develop and characterize HLW glasses with higher waste loadings. Results of this work have demonstrated the feasibility of increases in wasteloading from about 25 wt% to 33-50 wt% (based on oxide loading) in the glass depending on the waste stream. It is expected that these higher waste loading glasses will reduce the HLW canister production requirement by about 25% or more.

  10. Electronic waste management approaches: An overview

    Energy Technology Data Exchange (ETDEWEB)

    Kiddee, Peeranart [Centre for Environmental Risk Assessment and Remediation, University of South Australia, Mawson Lakes Campus, Adelaide, SA 5095 (Australia); Cooperative Research Centre for Contamination Assessment and Remediation of the Environment, Mawson Lakes Campus, Adelaide, SA 5095 (Australia); Naidu, Ravi, E-mail: ravi.naidu@crccare.com [Centre for Environmental Risk Assessment and Remediation, University of South Australia, Mawson Lakes Campus, Adelaide, SA 5095 (Australia); Cooperative Research Centre for Contamination Assessment and Remediation of the Environment, Mawson Lakes Campus, Adelaide, SA 5095 (Australia); Wong, Ming H. [Croucher Institute for Environmental Sciences, Department of Biology, Hong Kong Baptist University, Kowloon Tong (China)

    2013-05-15

    Highlights: ► Human toxicity of hazardous substances in e-waste. ► Environmental impacts of e-waste from disposal processes. ► Life Cycle Assessment (LCA), Material Flow Analysis (MFA), Multi Criteria Analysis (MCA) and Extended Producer Responsibility (EPR) to and solve e-waste problems. ► Key issues relating to tools managing e-waste for sustainable e-waste management. - Abstract: Electronic waste (e-waste) is one of the fastest-growing pollution problems worldwide given the presence if a variety of toxic substances which can contaminate the environment and threaten human health, if disposal protocols are not meticulously managed. This paper presents an overview of toxic substances present in e-waste, their potential environmental and human health impacts together with management strategies currently being used in certain countries. Several tools including Life Cycle Assessment (LCA), Material Flow Analysis (MFA), Multi Criteria Analysis (MCA) and Extended Producer Responsibility (EPR) have been developed to manage e-wastes especially in developed countries. The key to success in terms of e-waste management is to develop eco-design devices, properly collect e-waste, recover and recycle material by safe methods, dispose of e-waste by suitable techniques, forbid the transfer of used electronic devices to developing countries, and raise awareness of the impact of e-waste. No single tool is adequate but together they can complement each other to solve this issue. A national scheme such as EPR is a good policy in solving the growing e-waste problems.

  11. A multimodal transportation system routing implemented in waste collection

    Directory of Open Access Journals (Sweden)

    Masoud Rabbani

    2016-01-01

    Full Text Available Waste collection is an important municipal service that charges large expenditures to waste management (WM system. In this study, a hierarchical structure is proposed in order to minimize total cost of waste collection routing problem. Moreover, in second stage destructive environmental effects of waste transportation are minimized concurrently through taking advantage of a road/rail transportation system. In the proposed multimodal transportation system, waste packs are transferred to final destination while travel time and risk of environmental threatening is minimized. The discussed problem is formulated mathematically in two stages. In the first stage, a household waste collection routing problem is formulated while, in second stage a multimodal transportation system is routed to transfer waste packs to final destination through roads and railroads. In order to solve the proposed NP hard models, an improved genetic algorithm is developed. Comparison of the obtained results with those of GAMS for small-size samples validates the proposed models.

  12. 75 FR 58346 - Hazardous Waste Management System; Identification and Listing of Hazardous Waste

    Science.gov (United States)

    2010-09-24

    ... used the Delisting Risk Assessment Software (DRAS) Version 3.0 in the evaluation of the impact of the... AGENCY 40 CFR Part 261 Hazardous Waste Management System; Identification and Listing of Hazardous Waste...-line instructions for submitting comments. 2. E-mail: [email protected] . 3. Mail: Michelle Peace...

  13. Waste disposal

    CERN Multimedia

    2006-01-01

    We should like to remind you that you can have all commonplace, conventional waste (combustible, inert, wood, etc.) disposed of by the TS-FM Group. Requests for the removal of such waste should be made by contacting FM Support on tel. 77777 or by e-mail (Fm.Support@cern.ch). For requests to be acted upon, the following information must be communicated to FM Support: budget code to be debited for the provision and removal of the skip / container; type of skip required (1m3, 4 m3, 7 m3, 15 m3, 20 m3, 30 m3); nature of the waste to be disposed of (bulky objects, cardboard boxes, etc.); building concerned; details of requestor (name, phone number, department, group, etc.). We should also like to inform you that the TS-FM Group can arrange for waste to be removed from work-sites for firms under contract to CERN, provided that the prior authorisation of the CERN Staff Member in charge of the contract is obtained and the relevant disposal/handling charges are paid. You are reminded that the selective sorting...

  14. Waste disposal

    CERN Multimedia

    2006-01-01

    We should like to remind you that you can have all commonplace, conventional waste (combustible, inert, wood, etc.) disposed of by the TS-FM Group. Requests for the removal of such waste should be made by contacting FM Support on tel. 77777 or by e-mail (Fm.Support@cern.ch). For requests to be acted upon, the following information must be communicated to FM Support: budget code to be debited for the provision and removal of the skip / container. type of skip required (1m3, 4 m3, 7 m3, 15 m3, 20 m3, 30 m3). nature of the waste to be disposed of (bulky objects, cardboard boxes, etc.). building concerned. details of requestor (name, phone number, department, group, etc.). We should also like to inform you that the TS-FM Group can arrange for waste to be removed from work-sites for firms under contract to CERN, provided that the prior authorisation of the CERN Staff Member in charge of the contract is obtained and the relevant disposal/handling charges are paid. You are reminded that the selective sorting o...

  15. Human waste

    NARCIS (Netherlands)

    Amin, Md Nurul; Kroeze, Carolien; Strokal, Maryna

    2017-01-01

    Many people practice open defecation in south Asia. As a result, lot of human waste containing nutrients such as nitrogen (N) and phosphorus (P) enter rivers. Rivers transport these nutrients to coastal waters, resulting in marine pollution. This source of nutrient pollution is, however, ignored in

  16. Dairy Wastes.

    Science.gov (United States)

    Pico, Richard F.

    1978-01-01

    Presents a literature review of wastes from the dairy industry covering publications of 1976-77. This review covers: (1) government regulations; (2) ion-plant control of dairy effluents; (3) dairy effluent treatment methods; and (4) research on dairy effluents. A list of 26 references is also presented. (HM)

  17. Transfer Pricing

    DEFF Research Database (Denmark)

    Rohde, Carsten; Rossing, Christian Plesner

    trade internally as the units have to decide what prices should be paid for such inter-unit transfers. One important challenge is to uncover the consequences that different transfer prices have on the willingness in the organizational units to coordinate activities and trade internally. At the same time...

  18. Heat and mass transfer

    CERN Document Server

    Karwa, Rajendra

    2017-01-01

    This textbook presents the classical treatment of the problems of heat transfer in an exhaustive manner with due emphasis on understanding of the physics of the problems. This emphasis is especially visible in the chapters on convective heat transfer. Emphasis is laid on the solution of steady and unsteady two-dimensional heat conduction problems. Another special feature of the book is a chapter on introduction to design of heat exchangers and their illustrative design problems. A simple and understandable treatment of gaseous radiation has been presented. A special chapter on flat plate solar air heater has been incorporated that covers thermo-hydraulic modeling and simulation. The chapter on mass transfer has been written looking specifically at the needs of the students of mechanical engineering. The book includes a large number and variety of solved problems with supporting line diagrams. The author has avoided duplicating similar problems, while incorporating more application-based examples. All the end-...

  19. Signal Transmission on Power Lines

    DEFF Research Database (Denmark)

    Dalby, Arne Brejning

    1997-01-01

    coupled transmission line circuits like power line circuits, is based on finding the eigenvalues and eigenvectors for the matrix ZY, where Z and Y are the impedance- and admittance matrices for the coupled lines in W/m and S/m. In this paper a flow-graph representation of the relations beween voltage......- and current-vectors is presented for a general coupled line circuit. This flow-graph can be used to find any transfer function on a multiple coupled lossy transmission line circuit. In some cases, however, it is difficult to find the eigenvalues correctly. A correct analysis can thus not be made......In the analysis of power-line networks over a large frequency span, the time-domain method used in programs like EMTP (Electromagnetic Time domain Program) can not be used. A more rigorous analysis method must be employed. The correct analysis method (assuming TEM-mode propagation) for multiple...

  20. Hazardous waste and environmental trade: China`s issues

    Energy Technology Data Exchange (ETDEWEB)

    Ma Jiang [National Research Center for Science and Technology for Development, Beijing (China)

    1996-12-31

    By presenting some case studies, this paper analyzes China`s situation with regard to hazardous waste: its environmental trade, treatment, and management. The paper describes China`s experiences with the environmental trade of hazardous waste in both the internal and international market. Regulations for managing the import of waste are discussed, as are China`s major approaches to the trading of hazardous waste both at home and overseas. The major reasons for setting up the Asian-Pacific Regional Training Center for Technology Transfer and Environmental Sound Management of Wastes in China and the activities involved in this effort are also described. 1 tab.

  1. Multi-function Waste Tank Facility path forward engineering analysis -- Technical Task 3.6, Estimate of operational risk in 200 West Area

    Energy Technology Data Exchange (ETDEWEB)

    Coles, G.A.

    1995-04-28

    Project W-0236A has been proposed to provide additional waste tank storage in the 200 East and 200 West Areas. This project would construct two new waste tanks in the 200 West Area and four new tanks in the 200 East Area, and a related project (Project W-058) would construct a new cross-site line. These projects are intended to ensure sufficient space and flexibility for continued tank farm operations, including tank waste remediation and management of unforeseen contingencies. The objective of this operational risk assessment is to support determination of the adequacy of the free-volume capacity provided by Projects W-036A and W-058 and to determine related impacts. The scope of the assessment is the 200 West Area only and covers the time period from the present to the year 2005. Two different time periods were analyzed because the new cross-site tie line will not be available until 1999. The following are key insights: success of 200 West Area tank farm operations is highly correlated to the success of the cross-site transfer line and the ability of the 200 East Area to receive waste from 200 West; there is a high likelihood of a leak on a complexed single-shell tank in the next 4 years (sampling pending); there is a strong likelihood, in the next 4 years, that some combination of tank leaks, facility upsets, and cross-site line failure will require more free tank space than is currently available in Tank 241-SY-102; in the next 4 to 10 years, there is a strong likelihood that a combination of a cross-site line failure and the need to accommodate some unscheduled waste volume will require more free tank space than is presently available in Tank 241-SY-102; the inherent uncertainty in volume projections is in the range of 3 million gallons; new million-gallon tanks increase the ability to manage contingencies and unplanned events.

  2. Radioactive wastes: public attitudes toward disposal facilities

    Energy Technology Data Exchange (ETDEWEB)

    Lindell, M.K.; Earle, T.C.; Hebert, J.A.; Perry, R.W.

    1978-10-01

    Seventeen geographically widespread, established groups were selected which were expected to vary in their attitudes from strongly pronuclear to strongly antinuclear. People who tend to be politically active were chosen. The highest level of consensus was found on the need for site monitoring, site control, and information transfer in a waste repository. Overall, the results indicate that pronuclear respondents believe that the hazards of nuclear waste are similar to other industrial risks, while antinuclear respondents are less optimistic about safe storage of nuclear wastes and believe that nuclear power is different.

  3. Quantitative and Qualitative Investigation of Yazd Dental Center Waste

    Directory of Open Access Journals (Sweden)

    Mehdi Mokhtari

    2015-12-01

    Full Text Available Compared to other medical clinics, dental centers produce a relatively small amount of healthcare waste. However, they are responsible for the production of certain amounts of waste that can cause serious health and environmental hazards if not treated properly. Determining the quantity and quality of dental waste is quite necessary to plan the machinery, personnel, and transportation methods. In the current analytical cross-sectional study, 22 dental clinics were randomly selected from among 145 dental centers in Yazd. For each clinic, three samples were manually collected and distributed at the end of the work day once a week (the day was randomly chosen. The components were classified into four groups based on their characteristics and potential risk. Afterward, the collected data were analyzed using Excel. The mean per capita daily waste generation in the Yazd dental clinics was 80.179 g for each patient. In general, the Yazd dental clinics generate approximately 4 tons of waste every year. Out of this amount, infectious waste, domestic waste, chemical-pharmaceutical waste, and sharp waste account for 49.30%, 33.33%, 13.7%, and 4.2%, respectively. The results of the current study and the small amount of waste generated in Yazd suggest that a special safe site should be constructed for infectious, sharp, and keen waste; private companies should collect such waste and transfer it to this site after the waste is disinfected; and the waste should then be transferred to a municipal waste hygienic disposal site. In regard to chemical waste that may contain hazardous materials, like mercury, no suggestions other than safe burial are made.

  4. Antibiotic-Resistance Genes in Waste Water.

    Science.gov (United States)

    Karkman, Antti; Do, Thi Thuy; Walsh, Fiona; Virta, Marko P J

    2017-10-12

    Waste water and waste water treatment plants can act as reservoirs and environmental suppliers of antibiotic resistance. They have also been proposed to be hotspots for horizontal gene transfer, enabling the spread of antibiotic resistance genes between different bacterial species. Waste water contains antibiotics, disinfectants, and metals which can form a selection pressure for antibiotic resistance, even in low concentrations. Our knowledge of antibiotic resistance in waste water has increased tremendously in the past few years with advances in the molecular methods available. However, there are still some gaps in our knowledge on the subject, such as how active is horizontal gene transfer in waste water and what is the role of the waste water treatment plant in the environmental resistome? The purpose of this review is to briefly describe some of the main methods for studying antibiotic resistance in waste waters and the latest research and main knowledge gaps on the issue. In addition, some future research directions are proposed. Copyright © 2017 Elsevier Ltd. All rights reserved.

  5. Station Transfers

    Data.gov (United States)

    Department of Homeland Security — ixed rail transit external system transfers for systems within the Continental United States, Alaska, Hawaii, the District of Columbia, and Puerto Rico. The modes of...

  6. Regional solid waste management study

    Energy Technology Data Exchange (ETDEWEB)

    1992-09-01

    In 1990, the Lower Savannah Council of Governments (LSCOG) began dialogue with the United States Department of Energy (DOE) regarding possibilities for cooperation and coordination of solid waste management practices among the local governments and the Savannah River Site. The Department of Energy eventually awarded a grant to the Lower Savannah Council of Governments for the development of a study, which was initiated on March 5, 1992. After careful analysis of the region`s solid waste needs, this study indicates a network approach to solid waste management to be the most viable. The network involves the following major components: (1) Rural Collection Centers, designed to provide convenience to rural citizens, while allowing some degree of participation in recycling; (2) Rural Drop-Off Centers, designed to give a greater level of education and recycling activity; (3) Inert landfills and composting centers, designed to reduce volumes going into municipal (Subtitle D) landfills and produce useable products from yard waste; (4) Transfer Stations, ultimate landfill disposal; (5) Materials Recovery Facilities, designed to separate recyclables into useable and sellable units, and (6) Subtitle D landfill for burial of all solid waste not treated through previous means.

  7. Heat exchangers and recuperators for high temperature waste gases

    Science.gov (United States)

    Meunier, H.

    General considerations on high temperature waste heat recovery are presented. Internal heat recovery through combustion air preheating and external heat recovery are addressed. Heat transfer and pressure drop in heat exchanger design are discussed.

  8. High Line

    DEFF Research Database (Denmark)

    Kiib, Hans

    2015-01-01

    factories and warehouses on Gansevoort Street. Today the High Line is a beautiful park covered with new tiles, viewing platforms and smaller recreational areas. The park bridge has simple, uniform, urban fittings and features a variety of flowering plants, grasses, shrubs and trees from around the world......, and galleries. With the High Line, a new urban architectural typology has been created that is aesthetically enriching and sets new standards for urban transformation and urban life. “The park accommodates the wild, the cultivated, the intimate and the social. Access points are durational experiences designed...

  9. Rethinking the waste hierarchy

    Energy Technology Data Exchange (ETDEWEB)

    Rasmussen, C.; Vigsoe, D. (eds.)

    2005-03-01

    There is an increasing need to couple environmental and economic considerations within waste management. Consumers and companies alike generate ever more waste. The waste-policy challenges of the future lie in decoupling growth in waste generation from growth in consumption, and in setting priorities for the waste management. This report discusses the criteria for deciding priorities for waste management methods, and questions the current principles of EU waste policies. The basis for the discussion is the so-called waste hierarchy which has dominated the waste policy in the EU since the mid-1970s. The waste hierarchy ranks possible methods of waste management. According to the waste hierarchy, the very best solution is to reduce the amount of waste. After that, reuse is preferred to recycling which, in turn, is preferred to incineration. Disposal at a landfill is the least favourable solution. (BA)

  10. Other Special Waste

    DEFF Research Database (Denmark)

    Brogaard, Line Kai-Sørensen; Christensen, Thomas Højlund

    2011-01-01

    separately from MSW. Some of these other special wastes are briefly described in this chapter with respect to their definition, quantity and composition, and management options. The special wastes mentioned here are batteries, tires, polyvinylchloride (PVC) and food waste.......In addition to the main types of special waste related to municipal solid waste (MSW) mentioned in the previous chapters (health care risk waste, WEEE, impregnated wood, hazardous waste) a range of other fractions of waste have in some countries been defined as special waste that must be handled...

  11. Nevada Test Site Waste Acceptance Criteria (NTSWAC), Rev. 7-01

    Energy Technology Data Exchange (ETDEWEB)

    NSTec Environmental Management

    2009-05-01

    This document establishes the U.S. Department of Energy, National Nuclear Security Administration Nevada Site Office, Nevada Test Site Waste Acceptance Criteria (NTSWAC). The NTSWAC provides the requirements, terms, and conditions under which the Nevada Test Site (NTS) will accept low-level radioactive waste and mixed low-level waste for disposal. The NTSWAC includes requirements for the generator waste certification program, characterization, traceability, waste form, packaging, and transfer. The criteria apply to radioactive waste received at the NTS Area 3 and Area 5 Radioactive Waste Management Complex for disposal.

  12. Waste Management Project fiscal year 1998 multi-year work plan, WBS 1.2

    Energy Technology Data Exchange (ETDEWEB)

    Jacobsen, P.H.

    1997-09-23

    The Waste Management Project manages and integrates (non-TWRS) waste management activities at the site. Activities include management of Hanford wastes as well as waste transferred to Hanford from other DOE, Department of Defense, or other facilities. This work includes handling, treatment, storage, and disposal of radioactive, nonradioactive, hazardous, and mixed solid and liquid wastes. Major Waste Management Projects are the Solid Waste Project, Liquid Effluents Project, and Analytical Services. Existing facilities (e.g., grout vaults and canyons) shall be evaluated for reuse for these purposes to the maximum extent possible.

  13. Waste processing building with incineration technology

    Science.gov (United States)

    Wasilah, Wasilah; Zaldi Suradin, Muh.

    2017-12-01

    In Indonesia, waste problem is one of major problem of the society in the city as part of their life dynamics. Based on Regional Medium Term Development Plan of South Sulawesi Province in 2013-2018, total volume and waste production from Makassar City, Maros, Gowa, and Takalar Regency estimates the garbage dump level 9,076.949 m3/person/day. Additionally, aim of this design is to present a recommendation on waste processing facility design that would accommodate waste processing process activity by incineration technology and supported by supporting activity such as place of education and research on waste, and the administration activity on waste processing facility. Implementation of incineration technology would reduce waste volume up to 90% followed by relative negative impact possibility. The result planning is in form of landscape layout that inspired from the observation analysis of satellite image line pattern of planning site and then created as a building site pattern. Consideration of building orientation conducted by wind analysis process and sun path by auto desk project Vasari software. The footprint designed by separate circulation system between waste management facility interest and the social visiting activity in order to minimize the croos and thus bring convenient to the building user. Building mass designed by inseparable connection series system, from the main building that located in the Northward, then connected to a centre visitor area lengthways, and walked to the waste processing area into the residue area in the Southward area.

  14. Hanford Site annual dangerous waste report: Volume 1, Part 1, Generator dangerous waste report, dangerous waste

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-12-31

    This report contains information on hazardous wastes at the Hanford Site. Information consists of shipment date, physical state, chemical nature, waste description, waste number, weight, and waste designation.

  15. Method for forming microspheres for encapsulation of nuclear waste

    Science.gov (United States)

    Angelini, Peter; Caputo, Anthony J.; Hutchens, Richard E.; Lackey, Walter J.; Stinton, David P.

    1984-01-01

    Microspheres for nuclear waste storage are formed by gelling droplets containing the waste in a gelation fluid, transferring the gelled droplets to a furnace without the washing step previously used, and heating the unwashed gelled droplets in the furnace under temperature or humidity conditions that result in a substantially linear rate of removal of volatile components therefrom.

  16. Using geographic information system (GIS) to determine waste ...

    African Journals Online (AJOL)

    lyndon

    Full Length Research Paper. Using geographic information system (GIS) to determine waste transfer stations in relation to location of landfill sites in Accra Metropolis. Lyndon Nii Adjiri Sackey. Waste Landfills Ghana Limited, P.O. Box DT 1670, Adenta-Accra, Ghana. Received 26 May, 2015; Accepted 23 December, 2015.

  17. Development of a waste collection system for the space shuttle.

    Science.gov (United States)

    Behrend, A. F., Jr.; Swider, J. E., Jr.

    1972-01-01

    The development of a waste collection system to accommodate both male and female crew members for the space shuttle is discussed. The waste collection system, with emphasis on the collection and transfer of urine, is described. Human-interface requirements, zero-gravity influences and effects, and operational considerations required for total system design are discussed.

  18. Technological inductive power transfer systems

    Science.gov (United States)

    Madzharov, Nikolay D.; Nemkov, Valentin S.

    2017-05-01

    Inductive power transfer is a very fast expanding technology with multiple design principles and practical implementations ranging from charging phones and computers to bionic systems, car chargers and continuous power transfer in technological lines. Only a group of devices working in near magnetic field is considered. This article is devoted to overview of different inductive power transfer (IPT) devices. The review of literature in this area showed that industrial IPT are not much discussed and examined. The authors have experience in design and implementation of several types of IPTs belonging to wireless automotive chargers and to industrial application group. Main attention in the article is paid to principles and design of technological IPTs

  19. Development Of A Macro-Batch Qualification Strategy For The Hanford Tank Waste Treatment And Immobilization Plant

    Energy Technology Data Exchange (ETDEWEB)

    Herman, Connie C.

    2013-09-30

    following: Collection and characterization of samples for relevant process analytes from the tanks to be blended during the staging process; Initiation of qualification activities earlier in the staging process to optimize the campaign composition through evaluation from both a processing and glass composition perspective; Definition of the parameters that are important for processing in the WTP facilities (unit operations) across the anticipated range of wastes and as they relate to qualification-scale equipment; Performance of limited testing with simulants ahead of the waste feed qualification sample demonstration as needed to determine the available processing window for that campaign; and Demonstration of sufficient mixing in the staging tank to show that the waste qualification sample chemical and physical properties are representative of the transfers to be made to WTP. Potential flowcharts for derivatives of the Hanford waste feed qualification process are also provided in this report. While these recommendations are an extension of the existing WTP waste qualification program, they are more in line with the processes currently performed for SRS. The implementation of these processes at SRS has been shown to offer flexibility for processing, having identified potential processing issues ahead of the qualification or facility processing, and having provided opportunity to optimize waste loading and throughput in the DWPF.

  20. Waste minimization and pollution prevention awareness plan

    Energy Technology Data Exchange (ETDEWEB)

    1991-05-31

    The purpose of this plan is to document the Lawrence Livermore National Laboratory (LLNL) Waste Minimization and Pollution Prevention Awareness Program. The plan specifies those activities and methods that are or will be employed to reduce the quantity and toxicity of wastes generated at the site. The intent of this plan is to respond to and comply with (DOE's) policy and guidelines concerning the need for pollution prevention. The Plan is composed of a LLNL Waste Minimization and Pollution Prevention Awareness Program Plan and, as attachments, Program- and Department-specific waste minimization plans. This format reflects the fact that waste minimization is considered a line management responsibility and is to be addressed by each of the Programs and Departments. 14 refs.

  1. Waste remediation

    Energy Technology Data Exchange (ETDEWEB)

    Halas, Nancy J.; Nordlander, Peter; Neumann, Oara

    2017-01-17

    A system including a steam generation system and a chamber. The steam generation system includes a complex and the steam generation system is configured to receive water, concentrate electromagnetic (EM) radiation received from an EM radiation source, apply the EM radiation to the complex, where the complex absorbs the EM radiation to generate heat, and transform, using the heat generated by the complex, the water to steam. The chamber is configured to receive the steam and an object, wherein the object is of medical waste, medical equipment, fabric, and fecal matter.

  2. Advanced Energy and Water Recovery Technology from Low Grade Waste Heat

    Energy Technology Data Exchange (ETDEWEB)

    Dexin Wang

    2011-12-19

    performance was also done, which shows this heat transfer enhancement approach works well in a wide parameters range for typical flue gas conditions. Better understanding of condensing heat transfer mechanism for porous membrane heat transfer surfaces, shows higher condensation and heat transfer rates than non-permeable tubes, due to existence of the porous membrane walls. Laboratory testing has documented increased TMC performance with increased exhaust gas moisture content levels, which has exponentially increased potential markets for the product. The TMC technology can uniquely enhance waste heat recovery in tandem with water vapor recovery for many other industrial processes such as drying, wet and dry scrubber exhaust gases, dewatering, and water chilling. A new metallic substrate membrane tube development and molded TMC part fabrication method, provides an economical way to expand this technology for scaled up applications with less than 3 year payback expectation. A detailed market study shows a broad application area for this advanced waste heat and water recovery technology. A commercialization partner has been lined up to expand this technology to this big market. This research work led to new findings on the TMC working mechanism to improve its performance, better scale up design approaches, and economical part fabrication methods. Field evaluation work needs to be done to verify the TMC real world performance, and get acceptance from the industry, and pave the way for our commercial partner to put it into a much larger waste heat and waste water recovery market. This project is addressing the priority areas specified for DOE Industrial Technologies Program's (ITP's): Energy Intensive Processes (EIP) Portfolio - Waste Heat Minimization and Recovery platform.

  3. Waste Reduction Model

    Science.gov (United States)

    To help solid waste planners and organizations track/report GHG emissions reductions from various waste management practices. To assist in calculating GHG emissions of baseline and alternative waste management practices and provide the history of WARM.

  4. Hazardous Waste Generators

    Data.gov (United States)

    Vermont Center for Geographic Information — The HazWaste database contains generator (companies and/or individuals) site and mailing address information, waste generation, the amount of waste generated etc. of...

  5. The temporality of waste

    DEFF Research Database (Denmark)

    Madsen, Katrine Dahl; Jordt Jørgensen, Nanna; Læssøe, Jeppe

    Waste is, indisputably, one of the key issues of environmental concerns of our times. In an environment and sustainability education perspective, waste offers concrete entry points to issues of consumption, sustainability and citizenship. Still, waste education has received relatively little...

  6. Household hazardous waste

    DEFF Research Database (Denmark)

    Fjelsted, Lotte; Christensen, Thomas Højlund

    2007-01-01

    .) comprised 15-25% and foreign items comprised 10-20%. Water-based paint was the dominant part of the paint waste. The chemical composition of the paint waste and the paint-like waste was characterized by an analysis of 27 substances in seven waste fractions. The content of critical substances was tow......'Paint waste', a part of the 'household hazardous waste', amounting to approximately 5 tonnes was collected from recycling stations in two Danish cities. Sorting and analyses of the waste showed paint waste comprised approximately 65% of the mass, paint-like waste (cleaners, fillers, etc...... and the paint waste was less contaminated with heavy metals than was the ordinary household waste. This may suggest that households no longer need to source-segregate their paint if the household waste is incinerated, since the presence of a small quantity of solvent-based paint will not be harmful when...

  7. Informative document waste plastics

    NARCIS (Netherlands)

    Nagelhout D; Sein AA; Duvoort GL

    1989-01-01

    This "Informative document waste plastics" forms part of a series of "informative documents waste materials". These documents are conducted by RIVM on the indstruction of the Directorate General for the Environment, Waste Materials Directorate, in behalf of the program of

  8. Informative document packaging waste

    NARCIS (Netherlands)

    Joosten JM; Nagelhout D; Duvoort GL; Weerd M de

    1989-01-01

    This "informative document packaging waste" forms part of a series of "informative documents waste materials". These documents are conducted by RIVM on the instructions of the Direcotrate General for the Environment, Waste Materials Directorate, in behalf of the program of

  9. Biofilm responses to marine fish farm wastes

    Energy Technology Data Exchange (ETDEWEB)

    Sanz-Lazaro, Carlos, E-mail: carsanz@um.es [Departamento de Ecologia e Hidrologia, Facultad de Biologia, Universidad de Murcia, 30100 Murcia (Spain); Navarrete-Mier, Francisco; Marin, Arnaldo [Departamento de Ecologia e Hidrologia, Facultad de Biologia, Universidad de Murcia, 30100 Murcia (Spain)

    2011-03-15

    The changes in the biofilm community due to organic matter enrichment, eutrophication and metal contamination derived from fish farming were studied. The biofilm biomass, polysaccharide content, trophic niche and element accumulation were quantified along an environmental gradient of fish farm wastes in two seasons. Biofilm structure and trophic diversity was influenced by seasonality as well as by the fish farm waste load. Fish farming enhanced the accumulation of organic carbon, nutrients, selenium and metals by the biofilm community. The accumulation pattern of these elements was similar regardless of the structure and trophic niche of the community. This suggests that the biofilm communities can be considered a reliable tool for assessing dissolved aquaculture wastes. Due to the ubiquity of biofilms and its wide range of consumers, its role as a sink of dissolved wastes may have important implications for the transfer of aquaculture wastes to higher trophic levels in coastal systems. - Research highlights: > Biofilms can act as a trophic pathway of fish farm dissolved wastes. > Biofilms are reliable tools for monitoring fish farm dissolved wastes. > The influence of the fish farm dissolved wastes can be detected 120-350 m from farm. - Under the influence of fish farming biofilm accumulates organic carbon, nutrients, selenium and metals, regardless of the structure and trophic niche of the community.

  10. TRANSFERENCE LOVE

    OpenAIRE

    Deneanu, Daniela

    2011-01-01

    It is the psychoanalysis’ merit to have discovered one of most common phenomenon that happens in almost all kind of human relations, and that is transference. Psychoanalytic framework did not produce it, but stimulate it. Transference love—one of the most powerful tool used by the analyst to get to understand a pacient’s pattern of falling in love—is an emotional relationship (a conglomeration of affection, tenderness, friendship, erotic and sexual feelings) developed by a pacient for his/her...

  11. Seroepidemiology of infection with Toxoplasma gondii in waste pickers and waste workers in Durango, Mexico.

    Science.gov (United States)

    Alvarado-Esquivel, C; Liesenfeld, O; Márquez-Conde, J A; Cisneros-Camacho, A; Estrada-Martínez, S; Martínez-García, S A; González-Herrera, A; García-Corral, N

    2008-08-01

    Municipal waste is a potential source of infection for Toxoplasma gondii as it may contain contaminated meat with parasite tissue cysts and cat excrement with parasite oocysts. Therefore, we sought to determine the prevalence of T. gondii infection and associated characteristics in two populations exposed to municipal solid waste in Durango, Mexico. Ninety waste pickers and 83 waste workers of Durango City, Mexico were examined for T. gondii infection. They were tested for anti-T. gondii IgG and IgM antibodies using enzyme-linked immunoassays. In addition, socio-demographic and behavioural characteristics from each participant were obtained. Nineteen (21.1%) of the 90 waste pickers and seven (8.4%) of the 83 waste workers were positive for anti-T. gondii IgG antibodies. The difference in prevalence among the groups was statistically significant (P =0.03). Waste pickers aged 31-50 years showed a significantly higher prevalence (40.9%) than waste workers of the same age group (2.9%, P waste pickers but in none of the waste workers. The seroprevalence of T. gondii was significantly higher in workers of the waste transfer station (25.0%) than in drivers or helpers of waste vehicles (2.5%) (P =0.03). Multivariate analysis showed that T. gondii infection was associated with consuming food found in the garbage [adjusted odds ratio (OR) = 4.4; 95% confidence interval (CI) 1.6-11.8] and with lack of education (adjusted OR = 3.2; 95% CI 1.1-8.8). From this study, we conclude: (i) waste pickers may represent a risk group for T. gondii infection; (ii) lack of education might be a contributing factor for T. gondii infection; (iii) the higher the exposure to garbage, the higher the seroprevalence of T. gondii infection; (iv) Eating food products from the garbage may represent an important route for T. gondii infection.

  12. Municipal Solid Waste Management

    OpenAIRE

    Soni, Ajaykumar; Patil, Deepak; Argade, Kuldeep

    2016-01-01

    Waste management covers newly generated waste or waste from an onging process. When steps to reduce or even eliminate waste are to be considered, it is imperative that considerations should include total oversight, technical and management services of the total process.From raw material to the final product this includes technical project management expertise, technical project review and pollution prevention technical support and advocacy.Waste management also includes handling of waste, in...

  13. Supermarket food waste

    OpenAIRE

    Eriksson, Mattias

    2015-01-01

    Food waste occurs along the entire food supply chain and gives rise to great financial losses and waste of natural resources. The retail stage of the supply chain contributes significant masses of waste. Causes of this waste need to be identified before potential waste reduction measures can be designed, tested and evaluated. Therefore this thesis quantified retail food waste and evaluated selected prevention and valorisation measures, in order to determine how the carbon footprint of food ca...

  14. Assessment of alternatives for management of ORNL retrievable transuranic waste. Nuclear Waste Program: transuranic waste (Activity No. AR 05 15 15 0; ONL-WT04)

    Energy Technology Data Exchange (ETDEWEB)

    1980-10-01

    Since 1970, solid waste with TRU or U-233 contamination in excess of 10 ..mu..Ci per kilogram of waste has been stored in a retrievable fashion at ORNL, such as in ss drums, concrete casks, and ss-lined wells. This report describes the results of a study performed to identify and evaluate alternatives for management of this waste and of the additional waste projected to be stored through 1995. The study was limited to consideration of the following basic strategies: Strategy 1: Leave waste in place as is; Strategy 2: Improve waste confinement; and Strategy 3: Retrieve waste and process for shipment to a Federal repository. Seven alternatives were identified and evaluated, one each for Strategies 1 and 2 and five for Strategy 3. Each alternative was evaluated from the standpoint of technical feasibility, cost, radiological risk and impact, regulatory factors and nonradiological environmental impact.

  15. Guidelines for generators of hazardous chemical waste at LBL and guidelines for generators of radioactive and mixed waste at LBL. Revision 2

    Energy Technology Data Exchange (ETDEWEB)

    1993-10-01

    The purpose of this document is to provide the acceptance criteria for the transfer of hazardous chemical waste to LBL`s Hazardous Waste Handling Facility (HWHF). Hazardous chemical waste is a necessary byproduct of LBL`s research and technical support activities. This waste must be handled properly if LBL is to operate safely and provide adequate protection to staff and the environment. These guidelines describe how you, as a generator of hazardous chemical waste, can meet LBL`s acceptance criteria for hazardous chemical waste.

  16. 76 FR 13605 - Notice of Availability of Draft Waste Incidental to Reprocessing Evaluation for the Vitrification...

    Science.gov (United States)

    2011-03-14

    ... vitrified the waste (combined it at a high temperature with borosilicate glass) and transferred the molten glass-waste mixture into specially developed ] stainless steel canisters where the mixture hardened into a solid glass waste form. DOE used the vitrification melter as part of this process, specifically to...

  17. The Travel of Global Ideas of Waste Management

    DEFF Research Database (Denmark)

    Zapata Campos, Maria José; Zapata, Patrik

    2014-01-01

    Informal settlements in the global South cities are often neglected by formal solid waste collection services. In the city of Managua, the municipality and international and local NGOs recently implemented several waste management projects to provide waste collection in informal settlements...... by municipal truck to the municipal landfill. New institutionalism theory and the “travel metaphor” illuminate how the “waste transfer station” idea travelled to Managua from various international organizations. New urban infrastructure and waste management models introduced by donors were decoupled from...... existing waste management models and practices. Despite the organizational hypocrisy of the city administration, introducing this new model via pilot projects in three city districts challenges the logic of the existing centralized waste management system, which ignores the city's informal settlements...

  18. Chemical Waste and Allied Products.

    Science.gov (United States)

    Hung, Yung-Tse; Aziz, Hamidi Abdul; Ramli, Siti Fatihah; Yeh, Ruth Yu-Li; Liu, Lian-Huey; Huhnke, Christopher Robert

    2016-10-01

    This review of literature published in 2015 focuses on waste related to chemical and allied products. The topics cover the waste management, physicochemical treatment, aerobic granular, aerobic waste treatment, anaerobic granular, anaerobic waste treatment, chemical waste, chemical wastewater, fertilizer waste, fertilizer wastewater, pesticide wastewater, pharmaceutical wastewater, ozonation. cosmetics waste, groundwater remediation, nutrient removal, nitrification denitrification, membrane biological reactor, and pesticide waste.

  19. Transfer Timing

    OpenAIRE

    2003-01-01

    sim present Simulation Presentation Interactive Media Element This IME is used in the Computer Communications and Networks class offered in the Graduate School of Operations and Information Sciences. This introductory computer networking course provides the theory and principles of networking and communications protocols. This IME is used to help students understand data transfer options. CS3502 Computer Communications and Networks

  20. Seamless Transfers

    Science.gov (United States)

    Patton, Carol

    2017-01-01

    In 2014, approximately 7.3 million undergraduate students (42 percent) were enrolled in community colleges in the US, the latest statistic offered by the Community College Research Center. At some schools, like Cleveland State University (OH), more transfer students graduated in 2014 with a bachelor's degree than students who entered four-year…

  1. Membrane bioreactors for waste gas treatment.

    NARCIS (Netherlands)

    Reij, M.W.; Keurentjes, J.T.F.; Hartmans, S.

    1998-01-01

    This review describes the recent development of membrane reactors for biological treatment of waste gases. In this type of bioreactor gaseous pollutants are transferred through a membrane to the liquid phase, where micro-organisms degrade the pollutants. The membrane bioreactor combines the

  2. Waste heat recovery system

    Energy Technology Data Exchange (ETDEWEB)

    Ernst, Timothy C.; Zigan, James A.

    2017-12-19

    A waste heat recovery system includes a Rankine cycle (RC) circuit having a pump, a boiler, an energy converter, and a condenser fluidly coupled via conduits in that order, to provide additional work. The additional work is fed to an input of a gearbox assembly including a capacity for oil by mechanically coupling to the energy converter to a gear assembly. An interface is positioned between the RC circuit and the gearbox assembly to partially restrict movement of oil present in the gear assembly into the RC circuit and partially restrict movement of working fluid present in the RC circuit into the gear assembly. An oil return line is fluidly connected to at least one of the conduits fluidly coupling the RC components to one another and is operable to return to the gear assembly oil that has moved across the interface from the gear assembly to the RC circuit.

  3. Waste Separation Press (WSP): a mechanical pretreatment option for organic waste from source separation.

    Science.gov (United States)

    Jank, Anna; Müller, Wolfgang; Schneider, Irene; Gerke, Frederic; Bockreis, Anke

    2015-05-01

    An efficient biological treatment of source separated organic waste from household kitchens and gardens (biowaste) requires an adequate upfront mechanical preparation which possibly includes a hand sorting for the separation of contaminants. In this work untreated biowaste from households and gardens and the screen overflow >60mm of the same waste were mechanically treated by a Waste Separation Press (WSP). The WSP separates the waste into a wet fraction for biological treatment and a fraction of dry contaminants for incineration. The results show that it is possible to replace a hand sorting of contaminants, the milling and a screening of organic waste before the biological treatment by using the WSP. A special focus was put on the contaminants separation. The separation of plastic film from the untreated biowaste was 67% and the separation rate of glass was about 92%. About 90% of the organics were transferred to the fraction for further biological treatment. When treating the screen overflow >60mm with the WSP 86% of the plastic film and 88% of the glass were transferred to the contaminants fraction. 32% of the organic was transferred to the contaminants fraction and thereby lost for a further biological treatment. Additionally it was calculated that national standards for glass contaminants in compost can be met when using the WSP to mechanically treat the total biowaste. The loss of biogas by transferring biodegradable organics to the contaminants fraction was about 11% when preparing the untreated biowaste with the WSP. Copyright © 2015 Elsevier Ltd. All rights reserved.

  4. Microbial Transformation of TRU and Mixed Waste: Actinide Speciation and Waste Volume

    Energy Technology Data Exchange (ETDEWEB)

    Halada, Gary P

    2008-04-10

    In order to understand the susceptibility of transuranic and mixed waste to microbial degradation (as well as any mechanism which depends upon either complexation and/or redox of metal ions), it is essential to understand the association of metal ions with organic ligands present in mixed wastes. These ligands have been found in our previous EMSP study to limit electron transfer reactions and strongly affect transport and the eventual fate of radionuclides in the environment. As transuranic waste (and especially mixed waste) will be retained in burial sites and in legacy containment for (potentially) many years while awaiting treatment and removal (or remaining in place under stewardship agreements at government subsurface waste sites), it is also essential to understand the aging of mixed wastes and its implications for remediation and fate of radionuclides. Mixed waste containing actinides and organic materials are especially complex and require extensive study. The EMSP program described in this report is part of a joint program with the Environmental Sciences Department at Brookhaven National Laboratory. The Stony Brook University portion of this award has focused on the association of uranium (U(VI)) and transuranic analogs (Ce(III) and Eu(III)) with cellulosic materials and related compounds, with development of implications for microbial transformation of mixed wastes. The elucidation of the chemical nature of mixed waste is essential for the formulation of remediation and encapsulation technologies, for understanding the fate of contaminant exposed to the environment, and for development of meaningful models for contaminant storage and recovery.

  5. Guidelines for generators of hazardous chemical waste at LBL and guidelines for generators of radioactive and mixed waste at LBL

    Energy Technology Data Exchange (ETDEWEB)

    1991-09-01

    In part one of this document the Governing Documents and Definitions sections provide general guidelines and regulations applying to the handling of hazardous chemical wastes. The remaining sections provide details on how you can prepare your waste properly for transport and disposal. They are correlated with the steps you must take to properly prepare your waste for pickup. The purpose of the second part of this document is to provide the acceptance criteria for the transfer of radioactive and mixed waste to LBL's Hazardous Waste Handling Facility (HWHF). These guidelines describe how you, as a generator of radioactive or mixed waste, can meet LBL's acceptance criteria for radioactive and mixed waste.

  6. Introduction to Waste Management

    DEFF Research Database (Denmark)

    Christensen, Thomas Højlund

    2011-01-01

    Solid waste management is as old as human civilization, although only considered an engineering discipline for about one century. The change from the previous focus on public cleansing of the cities to modern waste management was primarily driven by industrialization, which introduced new materials...... and chemicals, dramatically changing the types and composition of waste, and by urbanization making waste management in urban areas a complicated and costly logistic operation. This book focuses on waste that commonly appears in the municipal waste management system. This chapter gives an introduction to modern...... waste management, including issues as waste definition, problems associated with waste, waste management criteria and approaches to waste management. Later chapters introduce aspects of engineering (Chapter 1.2), economics (Chapter 1.3) and regulation (Chapter 1.4)....

  7. Repository documentation rethought. A comprehensive approach from untreated waste to waste packages for final disposal

    Energy Technology Data Exchange (ETDEWEB)

    Anthofer, Anton Philipp; Schubert, Johannes [VPC GmbH, Dresden (Germany)

    2017-11-15

    The German Act on Reorganization of Responsibility for Nuclear Disposal (Entsorgungsuebergangsgesetz (EntsorgUebG)) adopted in June 2017 provides the energy utilities with the new option of transferring responsibility for their waste packages to the Federal Government. This is conditional on the waste packages being approved for delivery to the Konrad final repository. A comprehensive approach starts with the dismantling of nuclear facilities and extends from waste disposal and packaging planning to final repository documentation. Waste package quality control measures are planned and implemented as early as in the process qualification stage so that the production of waste packages that are suitable for final deposition can be ensured. Optimization of cask and loading configuration can save container and repository volume. Workflow planning also saves time, expenditure and exposure time for personnel at the facilities. VPC has evaluated this experience and developed it into a comprehensive approach.

  8. production lines

    Directory of Open Access Journals (Sweden)

    Jingshan Li

    2000-01-01

    Full Text Available In this work, serial production lines with finished goods buffers operating in the pull regime are considered. The machines are assumed to obey Bernoulli reliability model. The problem of satisfying customers demand is addressed. The level of demand satisfaction is quantified by the due-time performance (DTP, which is defined as the probability to ship to the customer a required number of parts during a fixed time interval. Within this scenario, the definitions of DTP bottlenecks are introduced and a method for their identification is developed.

  9. Informal Collection of Household Solid Waste in Three Towns of Anambra State, Nigeria

    Directory of Open Access Journals (Sweden)

    Egbu Anthony

    2014-10-01

    Full Text Available Management of urban solid waste implies the collection, transfer, treatment recycle, reuse and disposal of such waste. Collection of urban household solid waste traditionally rests with government agencies designated with such responsibility. Solid waste collection begins from storage at the household level to the final treatment or disposal point and represents the most important aspect of urban solid waste management. Little has however been written on urban household solid waste collection in Nigeria. Using empirical data from three urban areas of Anambra State, Nigeria, the paper examines the place of informal private solid waste collectors in household solid waste collection. The ANOVA technique is used to test the null hypothesis that the sample means of the distance to designated community/street solid waste collection containers in the residential neighbourhoods of the three towns are equal. We conclude on household patronage of informal private solid waste collectors as against government provided community/street collection containers in the areas studied.

  10. Hanford Site annual dangerous waste report: Volume 3, Part 1, Waste Management Facility report, dangerous waste

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-12-31

    This report contains information on hazardous wastes at the Hanford Site. Information consists of shipment date, physical state, chemical nature, waste description, handling method and containment vessel, waste number, waste designation, and amount of waste.

  11. Hanford Site annual dangerous waste report: Volume 3, Part 2, Waste Management Facility report, dangerous waste

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1944-12-31

    This report contains information on hazardous wastes at the Hanford Site. Information consists of shipment date, physical state, chemical nature, waste description, handling and containment vessel, waste number, waste designation and amount of waste.

  12. 40 CFR 35.925-15 - Treatment of industrial wastes.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 1 2010-07-01 2010-07-01 false Treatment of industrial wastes. 35.925... § 35.925-15 Treatment of industrial wastes. That the allowable project costs do not include (a) costs of interceptor or collector lines constructed exclusively, or almost exclusively, to serve industrial...

  13. 40 CFR 261.3 - Definition of hazardous waste.

    Science.gov (United States)

    2010-07-01

    ... F006 waste, in units identified as rotary kilns, flame reactors, electric furnaces, plasma arc furnaces...., spills from the unloading or transfer of materials from bins or other containers, leaks from pipes, valves or other devices used to transfer materials); minor leaks of process equipment, storage tanks or...

  14. Data Quality Objectives for Tank Farms Waste Compatibility Program

    Energy Technology Data Exchange (ETDEWEB)

    BANNING, D.L.

    1999-07-02

    There are 177 waste storage tanks containing over 210,000 m{sup 3} (55 million gal) of mixed waste at the Hanford Site. The River Protection Project (RPP) has adopted the data quality objective (DQO) process used by the U.S. Environmental Protection Agency (EPA) (EPA 1994a) and implemented by RPP internal procedure (Banning 1999a) to identify the information and data needed to address safety issues. This DQO document is based on several documents that provide the technical basis for inputs and decision/action levels used to develop the decision rules that evaluate the transfer of wastes. A number of these documents are presently in the process of being revised. This document will need to be revised if there are changes to the technical criteria in these supporting documents. This DQO process supports various documents, such as sampling and analysis plans and double-shell tank (DST) waste analysis plans. This document identifies the type, quality, and quantity of data needed to determine whether transfer of supernatant can be performed safely. The requirements in this document are designed to prevent the mixing of incompatible waste as defined in Washington Administrative Code (WAC) 173-303-040. Waste transfers which meet the requirements contained in this document and the Double-Shell Tank Waste Analysis Plan (Mulkey 1998) are considered to be compatible, and prevent the mixing of incompatible waste.

  15. Thermal Predictions of the Cooling of Waste Glass Canisters

    Energy Technology Data Exchange (ETDEWEB)

    Donna Post Guillen

    2014-11-01

    Radioactive liquid waste from five decades of weapons production is slated for vitrification at the Hanford site. The waste will be mixed with glass forming additives and heated to a high temperature, then poured into canisters within a pour cave where the glass will cool and solidify into a stable waste form for disposal. Computer simulations were performed to predict the heat rejected from the canisters and the temperatures within the glass during cooling. Four different waste glass compositions with different thermophysical properties were evaluated. Canister centerline temperatures and the total amount of heat transfer from the canisters to the surrounding air are reported.

  16. Characterization of Wastes from Pasteurizadora Sancti Spíritus.

    Directory of Open Access Journals (Sweden)

    Yolanda Margarita Carbonell Cabarga

    2012-04-01

    Full Text Available The present work is about the characterization of wastes from Pasteurizadora Sancti Spíritus and their influence on the emission of wastes from the other companies that pour them to the same oxidation lagoons. Its objectives are the following: Initial inspection of the treatment system, study and assessment of the environmental impacts per production line, assessment of the emissions of liquid and solid wastes and their destination, identification of chemicals, fuels and lubricants, characterization of the liquid wastes during the last 20 years. In the Materials and Methods section it was carried out a study and assessment of the environmental impacts generated by the organization, as well as a description of its solid wastes. Besides, the liquid wastes were characterized during 20 years, reaching the conclusion that the wastes resulting from the productions incorporated to the treatment system such as Nela and the Meat Enterprise´s productions remain biodegradable.

  17. Waste Package Lifting Calculation

    Energy Technology Data Exchange (ETDEWEB)

    H. Marr

    2000-05-11

    The objective of this calculation is to evaluate the structural response of the waste package during the horizontal and vertical lifting operations in order to support the waste package lifting feature design. The scope of this calculation includes the evaluation of the 21 PWR UCF (pressurized water reactor uncanistered fuel) waste package, naval waste package, 5 DHLW/DOE SNF (defense high-level waste/Department of Energy spent nuclear fuel)--short waste package, and 44 BWR (boiling water reactor) UCF waste package. Procedure AP-3.12Q, Revision 0, ICN 0, calculations, is used to develop and document this calculation.

  18. Commercial and Institutional Waste

    DEFF Research Database (Denmark)

    Christensen, Thomas Højlund; Fruergaard, Thilde

    2011-01-01

    Commercial and institutional waste is primarily from retail (stores), hotels, restaurants, health care (except health risk waste), banks, insurance companies, education, retirement homes, public services and transport. Within some of these sectors, e.g. retail and restaurants, large variations...... is handled in the municipal waste system, where information is easily accessible. An important part of commercial and institutional waste is packaging waste, and enterprises with large quantities of clean paper, cardboard and plastic waste may have their own facilities for baling and storing their waste...

  19. Municipal solid waste composition determination supporting the integrated solid waste management system in the island of Crete.

    Science.gov (United States)

    Gidarakos, E; Havas, G; Ntzamilis, P

    2006-01-01

    A one-year survey was conducted in the greater region of Crete (located at the lower region of the Aegean Sea) for the purpose of identifying waste composition (including chemical and physical characterization), as well as any seasonal variation. The investigation was carried out repeatedly at seven landfills and one transfer station in Crete, in four phases. Each sampling phase corresponded to a season (autumn, winter, spring, summer). ASTM D5231-92(2003) standard method and RCRA Waste Sampling Draft Technical Guidance were used. Hand sorting was used for classifying the collected wastes into the following categories: plastics, paper, metals, aluminium, leather-wood-textiles-rubbers, organic wastes, non-combustibles and miscellaneous. Further analysis included proximate and ultimate analysis of combustible materials. Metals such as lead, cadmium and mercury were also investigated. The results show that there has been a significant decrease of organic wastes during the last decade due to the increase of packaging materials, as a result of a change in consumption patterns. Three main waste categories were determined: organic wastes, paper and plastics, which combined represent 76% of the total waste in Crete. Furthermore, a high fraction of glass and a seasonal variation of aluminium indicate a strong correlation of waste composition with certain human activities, such as tourism. There is also a variation between the municipal solid waste (MSW) composition in the region of Crete (2003-2004) and MSW composition suggested in the National Solid Waste Planning (2000) [National Solid Waste Planning, 2000. Completion and particularization of Common Ministerial Act 113944//1944/1997: National Solid Waste Planning, June 2000]. The results of this survey are to be utilized by the regional solid waste authorities in order to establish an integrated waste treatment site, capable of fulfilling the regional waste management demands.

  20. Characterization of major waste data sources

    Energy Technology Data Exchange (ETDEWEB)

    Cordes, R.; Eisenhauer, J.

    1991-09-03

    The US Department of Energy (DOE) recently initiated the Industrial Waste Reduction Program, which seeks to develop and commercialize waste reduction technologies and practices that will reduce industrial energy use. The Industrial Waste Reduction Program, like the other programs under DOE's Office of Industrial Technologies (OIT), works with industry to focus research and development resources according to industry needs and market opportunities. The Program consists of five fundamental elements: industrial waste characterization, opportunity assessments, technology research and development, technology and information transfer, and, institutional analysis. This report is a product of efforts initiated under the first of these program elements, Industrial Waste Characterization. Its purpose is to increase understanding of the types and magnitudes of industrial waste streams. In particular, this report presents the key characteristics of selected waste, energy, and economic data sources in an effort to clarify the scope, consistency, and limitations of the data. It is expected that this information will be used in another element of the program, Opportunity Assessments. That effort will identify priority technology needs by evaluating the available data; expert advice from industry, government, and academia; and independent analyses. 33 refs.

  1. Stability of disposal rooms during waste retrieval

    Energy Technology Data Exchange (ETDEWEB)

    Brandshaug, T.

    1989-03-01

    This report presents the results of a numerical analysis to determine the stability of waste disposal rooms for vertical and horizontal emplacement during the period of waste retrieval. It is assumed that waste retrieval starts 50 years after the initial emplacement of the waste, and that access to and retrieval of the waste containers take place through the disposal rooms. It is further assumed that the disposal rooms are not back-filled. Convective cooling of the disposal rooms in preparation for waste retrieval is included in the analysis. Conditions and parameters used were taken from the Nevada Nuclear Waste Storage Investigation (NNWSI) Project Site Characterization Plan Conceptual Design Report (MacDougall et al., 1987). Thermal results are presented which illustrate the heat transfer response of the rock adjacent to the disposal rooms. Mechanical results are presented which illustrate the predicted distribution of stress, joint slip, and room deformations for the period of time investigated. Under the assumption that the host rock can be classified as ``fair to good`` using the Geomechanics Classification System (Bieniawski, 1974), only light ground support would appear to be necessary for the disposal rooms to remain stable. 23 refs., 28 figs., 2 tabs.

  2. Understanding radioactive waste

    Energy Technology Data Exchange (ETDEWEB)

    Murray, R.L.

    1981-12-01

    This document contains information on all aspects of radioactive wastes. Facts are presented about radioactive wastes simply, clearly and in an unbiased manner which makes the information readily accessible to the interested public. The contents are as follows: questions and concerns about wastes; atoms and chemistry; radioactivity; kinds of radiation; biological effects of radiation; radiation standards and protection; fission and fission products; the Manhattan Project; defense and development; uses of isotopes and radiation; classification of wastes; spent fuels from nuclear reactors; storage of spent fuel; reprocessing, recycling, and resources; uranium mill tailings; low-level wastes; transportation; methods of handling high-level nuclear wastes; project salt vault; multiple barrier approach; research on waste isolation; legal requiremnts; the national waste management program; societal aspects of radioactive wastes; perspectives; glossary; appendix A (scientific American articles); appendix B (reference material on wastes). (ATT)

  3. Citric Acid Fermentation by Aspergillus niger on Low Sugar Concentrations and Cotton Waste

    OpenAIRE

    Kiel, Hildegard; Guvrin, Rumia; Henis, Yigal

    1981-01-01

    The possible use of cotton waste as a carbohydrate source of citric acid production by Aspergillus niger was examined. No citric acid was produced when A. niger was grown on cotton waste as a sole carbon source. In two-stage fermentations, however, mycelium obtained from surface cultures in cotton waste medium yielded more citric acid when transferred to sucrose-containing media than when directly inoculated to sucrose-containing media. It is concluded that cotton waste can be used for saving...

  4. Parallel Lines

    Directory of Open Access Journals (Sweden)

    James G. Worner

    2017-05-01

    Full Text Available James Worner is an Australian-based writer and scholar currently pursuing a PhD at the University of Technology Sydney. His research seeks to expose masculinities lost in the shadow of Australia’s Anzac hegemony while exploring new opportunities for contemporary historiography. He is the recipient of the Doctoral Scholarship in Historical Consciousness at the university’s Australian Centre of Public History and will be hosted by the University of Bologna during 2017 on a doctoral research writing scholarship.   ‘Parallel Lines’ is one of a collection of stories, The Shapes of Us, exploring liminal spaces of modern life: class, gender, sexuality, race, religion and education. It looks at lives, like lines, that do not meet but which travel in proximity, simultaneously attracted and repelled. James’ short stories have been published in various journals and anthologies.

  5. 7 CFR 1779.88 - Transfers and assumptions.

    Science.gov (United States)

    2010-01-01

    ... AGRICULTURE (CONTINUED) WATER AND WASTE DISPOSAL PROGRAMS GUARANTEED LOANS § 1779.88 Transfers and assumptions... transfer fees will be a standard fee plus the cost of the appraisal. (2) The lender will collect and submit... be filed, registered, or recorded as appropriate and legally permissible. (4) The assumption will be...

  6. Utrecht Radiative Transfer Courses

    Science.gov (United States)

    Rutten, R. J.

    2003-01-01

    The Utrecht course ``The Generation and Transport of Radiation'' teaches basic radiative transfer to second-year students. It is a much-expanded version of the first chapter of Rybicki & Lightman's ``Radiative Processes in Astrophysics''. After this course, students understand why intensity is measured per steradian, have an Eddington-Barbier feel for optically thick line formation, and know that scattering upsets LTE. The text is a computer-aided translation by Ruth Peterson of my 1992 Dutch-language course. My aim is to rewrite this course in non-computer English and make it web-available at some time. In the meantime, copies of the Peterson translation are made yearly at Uppsala -- ask them, not me. Eventually it should become a textbook. The Utrecht course ``Radiative Transfer in Stellar Atmospheres'' is a 30-hour course for third-year students. It treats NLTE line formation in plane-parallel stellar atmospheres at a level intermediate between the books by Novotny and Boehm-Vitense, and Mihalas' ``Stellar Atmospheres''. After this course, students appreciate that epsilon is small, that radiation can heat or cool, and that computers have changed the field. This course is web-available since 1995 and is regularly improved -- but remains incomplete. Eventually it should become a textbook. The three Utrecht exercise sets ``Stellar Spectra A: Basic Line Formation'', ``Stellar Spectra B: LTE Line Formation'', and ``Stellar Spectra C: NLTE Line Formation'' are IDL-based computer exercises for first-year, second-year, and third-year students, respectively. They treat spectral classification, Saha-Boltzmann population statistics, the curve of growth, the FAL-C solar atmosphere model, the role of H-minus in the solar continuum, LTE formation of Fraunhofer lines, inversion tactics, the Feautrier method, classical lambda iteration, and ALI computation. The first two sets are web-available since 1998; the third will follow. Acknowledgement. Both courses owe much to previous

  7. Nuclear waste solidification

    Science.gov (United States)

    Bjorklund, William J.

    1977-01-01

    High level liquid waste solidification is achieved on a continuous basis by atomizing the liquid waste and introducing the atomized liquid waste into a reaction chamber including a fluidized, heated inert bed to effect calcination of the atomized waste and removal of the calcined waste by overflow removal and by attrition and elutriation from the reaction chamber, and feeding additional inert bed particles to the fluidized bed to maintain the inert bed composition.

  8. Municipal Solid Waste Resources

    Energy Technology Data Exchange (ETDEWEB)

    None

    2016-06-01

    Municipal solid waste (MSW) is a source of biomass material that can be utilized for bioenergy production with minimal additional inputs. MSW resources include mixed commercial and residential garbage such as yard trimmings, paper and paperboard, plastics, rubber, leather, textiles, and food wastes. Waste resources such as landfill gas, mill residues, and waste grease are already being utilized for cost-effective renewable energy generation. MSW for bioenergy also represents an opportunity to divert greater volumes of residential and commercial waste from landfills.

  9. Line locking and SS 433

    Science.gov (United States)

    Pekarevich, M.; Piran, T.; Shaham, J.

    1984-01-01

    The general problem of acceleration by line locking in an optically thin medium is considered. Analytic solutions to the coupled equations of radiation transfer and matter motion are presented. Using these solutions, restrictions on the physical conditions of the accelerated matter are derived. By applying these conditions to SS 433, it is found that if the absorbing ion is light (hydrogen or helium), the matter must be highly clumped, and the acceleration has to begin at approximately 10 to the 12th cm. Line-locking acceleration with a hydrogen-like heavy ion such as iron demands higher than solar ion abundance.

  10. Delaminated Transfer of CVD Graphene

    Science.gov (United States)

    Clavijo, Alexis; Mao, Jinhai; Tilak, Nikhil; Altvater, Michael; Andrei, Eva

    Single layer graphene is commonly synthesized by dissociation of a carbonaceous gas at high temperatures in the presence of a metallic catalyst in a process known as Chemical Vapor Deposition or CVD. Although it is possible to achieve high quality graphene by CVD, the standard transfer technique of etching away the metallic catalyst is wasteful and jeopardizes the quality of the graphene film by contamination from etchants. Thus, development of a clean transfer technique and preservation of the parent substrate remain prominent hurdles to overcome. In this study, we employ a copper pretreatment technique and optimized parameters for growth of high quality single layer graphene at atmospheric pressure. We address the transfer challenge by utilizing the adhesive properties between a polymer film and graphene to achieve etchant-free transfer of graphene films from a copper substrate. Based on this concept we developed a technique for dry delamination and transferring of graphene to hexagonal boron nitride substrates, which produced high quality graphene films while at the same time preserving the integrity of the copper catalyst for reuse. DOE-FG02-99ER45742, Ronald E. McNair Postbaccalaureate Achievement Program.

  11. Saturation transfer EPR (ST-EPR) for dating biocarbonates containing large amount of Mn{sup 2+}: separation of SO{sub 3}{sup -} and CO{sub 2}{sup -} lines and geochronology of Brazilian fish fossil

    Energy Technology Data Exchange (ETDEWEB)

    Sastry, M.D.; Andrade, M.B.; Watanabe, Shigueo E-mail: watanabe@if.usp.br

    2003-04-01

    A method using saturation transfer EPR (ST-EPR) is shown to be feasible for detecting EPR signal of radiation-induced defects in biocarbonates containing large amount of Mn{sup 2+}. The ST-EPR measurements conducted at room temperature on fish fossil of Brazilian origin, enabled the identification of CO{sub 2}{sup -} and SO{sub 3}{sup -} radical ions, by partially suppressing the intense signal from Mn{sup 2+} when the signal are detected 90 deg. out of phase with magnetic field modulating signal and at high microwave power (50 mW). Using these signals the age of fish fossil is estimated to be (36{+-}5) Ma.

  12. Solid and Liquid Waste Drying Bag

    Science.gov (United States)

    Litwiller, Eric (Inventor); Hogan, John A. (Inventor); Fisher, John W. (Inventor)

    2009-01-01

    Method and system for processing waste from human activities, including solids, liquids and vapors. A fluid-impermeable bag, lined with a liquid-impermeable but vapor-permeable membrane, defining an inner bag, is provided. A vacuum force is provided to extract vapors so that the waste is moved toward a selected region in the inner bag, extracted vapors, including the waste vapors and vaporized portions of the waste liquids are transported across the membrane, and most or all of the solids remain within the liner. Extracted vapors are filtered, and sanitized components thereof are isolated and optionally stored. The solids remaining within the liner are optionally dried and isolated for ultimate disposal.

  13. Solid Waste Management Practices in the Eastern Province of Saudi Arabia

    Science.gov (United States)

    Khan, Hasin U.; Husain, Tahir; Khan, Suhail M.

    1987-11-01

    Solid waste management practices in the Eastern Province of Saudi Arabia are reviewed. The officials of various municipalities and agencies responsible for collecting and disposing of municipal waste were interviewed. The refuse generation rate found is in the range of 1.61 2.72 kg per capita per day. The refuse composition data indicate a high percentage of glass, metals, and wood. For storage purposes, 0.2-m3 barrels are used in residential areas and 0.75 to 1.50 m3-capacity containers are used in commerical areas. The present solid-waste collection system is labor-intensive, and a significant part of the budget is spent on collection and haul operations. The unit collection and haul cost is much higher than the unit disposal cost of refuse. The direct haul of refuse is the common practice, and the use of transfer stations has not yet been considered. It is also observed that the disposal methods used at these sites are not in line with modern techniques for refuse disposal. Landfilling and combined burning and landfilling are the common disposal methods at all the sites.

  14. Tank waste remediation system retrieval and disposal mission key enabling assumptions

    Energy Technology Data Exchange (ETDEWEB)

    Baldwin, J.H.

    1998-01-09

    An overall systems approach has been applied to develop action plans to support the retrieval and immobilization waste disposal mission. The review concluded that the systems and infrastructure required to support the mission are known. Required systems are either in place or plans have been developed. An analysis of the programmatic, management and technical activities necessary to declare Readiness to Proceed with execution of the mission demonstrates that the system, people, and hardware will be on line and ready to support the private contractors. The systems approach included defining the retrieval and immobilized waste disposal mission requirements and evaluating the readiness of the TWRS contractor to supply waste feed to the private contractors in June 2002. The Phase 1 feed delivery requirements from the Private Contractor Request for Proposals were reviewed, transfer piping routes were mapped on it, existing systems were evaluated, and upgrade requirements were defined. Technical Basis Reviews were completed to define work scope in greater detail, cost estimates and associated year by year financial analyses were completed. Personnel training, qualifications, management systems and procedures were reviewed and shown to be in place and ready to support the Phase 1B mission. Key assumptions and risks that could negatively impact mission success were evaluated and appropriate mitigative actions plans were planned and scheduled.

  15. Development of a household waste treatment subsystem, volume 1. [with water conservation features

    Science.gov (United States)

    Gresko, T. M.; Murray, R. W.

    1973-01-01

    The domestic waste treatment subsystem was developed to process the daily liquid and non-metallic solid wastes provided by a family of four people. The subsystem was designed to be connected to the sewer line of a household which contained water conservation features. The system consisted of an evaporation technique to separate liquids from solids, an incineration technique for solids reduction, and a catalytic oxidizer for eliminating noxious gases from evaporation and incineration processes. All wastes were passed through a grinder which masticated the solids and deposited them in a settling tank. The liquids were transferred through a cleanable filter into a holding tank. From here the liquids were sprayed into an evaporator and a spray chamber where evaporation occurred. The resulting vapors were processed by catalytic oxidation. Water and latent energy were recovered in a combination evaporator/condenser heat exchanger. The solids were conveyed into an incinerator and reduced to ash while the incineration gases were passed through the catalytic oxidizer along with the processed water vapor.

  16. Innovating e-waste management: From macroscopic to microscopic scales.

    Science.gov (United States)

    Zeng, Xianlai; Yang, Congren; Chiang, Joseph F; Li, Jinhui

    2017-01-01

    Waste electrical and electronic equipment (WEEE or e-waste) has become a global problem, due to its potential environmental pollution and human health risk, and its containing valuable resources (e.g., metals, plastics). Recycling for e-waste will be a necessity, not only to address the shortage of mineral resources for electronics industry, but also to decline environmental pollution and human health risk. To systematically solve the e-waste problem, more attention of e-waste management should transfer from macroscopic to microscopic scales. E-waste processing technology should be significantly improved to diminish and even avoid toxic substance entering into downstream of material. The regulation or policy related to new production of hazardous substances in recycled materials should also be carried out on the agenda. All the findings can hopefully improve WEEE legislation for regulated countries and non-regulated countries. Copyright © 2016 Elsevier B.V. All rights reserved.

  17. [Influence of impurities on waste plastics pyrolysis: products and emissions].

    Science.gov (United States)

    Zhao, Lei; Wang, Zhong-Hui; Chen, De-Zhen; Ma, Xiao-Bo; Luan, Jian

    2012-01-01

    The study is aimed to evaluate the impact of impurities like food waste, paper, textile and especially soil on the pyrolysis of waste plastics. For this purpose, emissions, gas and liquid products from pyrolysis of waste plastics and impurities were studied, as well as the transfer of element N, Cl, S from the substrates to the pyrolysis products. It was found that the presence of food waste would reduce the heat value of pyrolysis oil to 27 MJ/kg and increase the moisture in the liquid products, therefore the food residue should be removed from waste plastics; and the soil, enhance the waste plastics' pyrolysis by improving the quality of gas and oil products. The presence of food residue, textile and paper leaded to higher gas emissions.

  18. VT Digital Line Graph Miscellaneous Transmission Lines

    Data.gov (United States)

    Vermont Center for Geographic Information — (Link to Metadata) This datalayer is comprised of Miscellaineous Transmission Lines. Digital line graph (DLG) data are digital representations of cartographic...

  19. Waste catalysts for waste polymer.

    Science.gov (United States)

    Salmiaton, A; Garforth, A

    2007-01-01

    Catalytic cracking of high-density polyethylene (HDPE) over fluid catalytic cracking (FCC) catalysts (1:6 ratio) was carried out using a laboratory fluidized bed reactor operating at 450 degrees C. Two fresh and two steam deactivated commercial FCC catalysts with different levels of rare earth oxide (REO) were compared as well as two used FCC catalysts (E-Cats) with different levels of metal poisoning. Also, inert microspheres (MS3) were used as a fluidizing agent to compare with thermal cracking process at BP pilot plant at Grangemouth, Scotland, which used sand as its fluidizing agent. The results of HDPE degradation in terms of yield of volatile hydrocarbon product are fresh FCC catalysts>steamed FCC catalysts approximately used FCC catalysts. The thermal cracking process using MS3 showed that at 450 degrees C, the product distribution gave 46 wt% wax, 14% hydrocarbon gases, 8% gasoline, 0.1% coke and 32% nonvolatile product. In general, the product yields from HDPE cracking showed that the level of metal contamination (nickel and vanadium) did not affect the product stream generated from polymer cracking. This study gives promising results as an alternative technique for the cracking and recycling of polymer waste.

  20. Demonstrating Reliable High Level Waste Slurry Sampling Techniques to Support Hanford Waste Processing

    Energy Technology Data Exchange (ETDEWEB)

    Kelly, Steven E.

    2013-11-11

    The Hanford Tank Operations Contractor (TOC) and the Hanford Waste Treatment and Immobilization Plant (WTP) contractor are both engaged in demonstrating mixing, sampling, and transfer system capability using simulated Hanford High-Level Waste (HL W) formulations. This work represents one of the remaining technical issues with the high-level waste treatment mission at Hanford. The TOC must demonstrate the ability to adequately mix and sample high-level waste feed to meet the WTP Waste Acceptance Criteria and Data Quality Objectives. The sampling method employed must support both TOC and WTP requirements. To facilitate information transfer between the two facilities the mixing and sampling demonstrations are led by the One System Integrated Project Team. The One System team, Waste Feed Delivery Mixing and Sampling Program, has developed a full scale sampling loop to demonstrate sampler capability. This paper discusses the full scale sampling loops ability to meet precision and accuracy requirements, including lessons learned during testing. Results of the testing showed that the Isolok(R) sampler chosen for implementation provides precise, repeatable results. The Isolok(R) sampler accuracy as tested did not meet test success criteria. Review of test data and the test platform following testing by a sampling expert identified several issues regarding the sampler used to provide reference material used to judge the Isolok's accuracy. Recommendations were made to obtain new data to evaluate the sampler's accuracy utilizing a reference sampler that follows good sampling protocol.

  1. Size or check waste heat boilers quickly

    Energy Technology Data Exchange (ETDEWEB)

    Ganapathy, V.

    1984-09-01

    Fire tube boilers are widely used to recover energy from waste gas streams commonly found in chemical plants, refineries and power plants. Typical examples are exhaust gases from gas turbines and diesel engines, and effluents from sulfuric acid, nitric acid and hydrogen plants. Generally, they are used for low-pressure steam generation. Typical arrangement of a fire tube boiler is shown. Sizing of waste heat boilers is quite an involved procedure. However, using the method described here one can estimate the performance of the boiler at various load conditions, in addition to designing the heat transfer surface for a given duty. Several advantages are claimed for this approach.

  2. Hazardous Waste: Learn the Basics of Hazardous Waste

    Science.gov (United States)

    ... Agency Search Search Hazardous Waste Contact Us Share Learn the Basics of Hazardous Waste Hazardous waste that ... Regulations part 261 . Select a question below to learn more about each step in the hazardous waste ...

  3. A prospective survey of blood products transferred with patients during inter-hospital transfers in the East of England.

    Science.gov (United States)

    Bamber, J H; O'Brien, J; Foukaneli, D; Dhesi, A

    2015-10-01

    A prospective survey was undertaken of blood products transferred with patients during inter-hospital transfers by ambulance in the East of England (population six million) There is little published information on the number and fate of blood products transferred with patients during inter-hospital transfers, although there are concerns about quality assurance and traceability of these blood products. Recent national guidance has been issued, but adherence to this guidance is uncertain. A 6-month survey was undertaken of all inter-hospital transfers of blood products with patients within the East of England using routine data captured by established transfer of blood documentation. There were 45 transfer episodes of which 44 involved the transfer of red blood cells. In total, 148 units of red blood cells were transferred, of which 6% were transfused en route, 3% transfused at the destination hospital, 35% were wasted and for 18% the fate could not be established. The remainder were transferred into the blood stock of the destination hospital. The small proportion of blood products that were transfused raises questions about the necessity of the transfer of blood products with some patients particularly considering the higher percentage of wasted or untraced products. When transfers occur, there should be better communication between hospital transfusion laboratories assisted by adherence to national and regionally agreed policies. © 2015 British Blood Transfusion Society.

  4. Hanford Site annual dangerous waste report: Volume 1, Part 2, Generator dangerous waste report, dangerous waste

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-12-31

    This report contains information on hazardous materials at the Hanford Site. Information consists of shipment date, physical state, chemical nature, waste description, waste number, weight, and waste designation.

  5. Productive efficiency of public and private solid waste logistics and its implications for waste management policy

    Directory of Open Access Journals (Sweden)

    Daisuke Ichinose

    2013-03-01

    Full Text Available This paper measures the productive efficiency of municipal solid waste (MSW logistics by applying data envelopment analysis (DEA to cross-sectional data of prefectures in Japan. Either through public operations or by outsourcing to private waste collection operators, prefectural governments possess the fundamental authority over waste processing operations in Japan. Therefore, we estimate a multi-input multi-output production efficiency at the prefectural level via DEA, employing several different model settings. Our data classify the MSW into household solid waste (HSW and business solid waste (BSW collected by both private and public operators as separate outputs, while the numbers of trucks and workers used by private and public operators are used as inputs. The results consistently show that geographical characteristics, such as the number of inhabited remote islands, are relatively more dominant factors for determining inefficiency. While the implication that a minimum efficient scale is not achieved in these small islands is in line with the literature suggesting that waste logistics has increasing returns at the municipal level, our results indicate that waste collection efficiency in Japan is well described by CRS technology at the prefectural level. The results also show that prefectures with higher private-sector participation, measured in terms of HSW collection, are more efficient, whereas a higher private–labor ratio negatively affects efficiency. We also provide evidence that prefectures with inefficient MSW logistics have a higher tendency of suffering from the illegal dumping of industrial waste.

  6. Low-level waste disposal - Grout issue and alternative waste form technology

    Energy Technology Data Exchange (ETDEWEB)

    Epstein, J.L. [Westinghouse Hanford Co., Richland, WA (United States); Westski, J.H. Jr. [Pacific Northwest Lab., Richland, WA (United States)

    1993-02-01

    Based on the Record of Decision (1) for the Hanford Defense Waste Environmental Impact Statement (HDW-EIS) (2), the US Department of Energy (DOE) is planning to dispose of the low-level fraction of double-shell tank (DST) waste by solidifying the liquid waste as a cement-based grout placed in near-surface, reinforced, lined concrete vaults at the Hanford Site. In 1989, the Hanford Grout Disposal Program (HGDP) completed a full-scale demonstration campaign by successfully grouting 3,800 cubic meters (1 million gallons) of low radioactivity, nonhazardous, phosphate/sulfate waste (PSW), mainly decontamination solution from N Reactor. The HGDP is now preparing for restart of the facility to grout a higher level activity, mixed waste double-shell slurry feed (DSSF). This greater radionuclide and hazardous waste content has resulted in a number of issues confronting the disposal system and the program. This paper will present a brief summary of the Grout Treatment Facility`s components and features and will provide a status of the HGDP, concentrating on the major issues and challenges resulting from the higher radionuclide and hazardous content of the waste. The following major issues will be discussed: Formulation (cementitious mix) development; the Performance Assessment (PA) (3) to show compliance of the disposal system to long-term environmental protection objectives; and the impacts of grouting on waste volume projections and tank space needs.

  7. Two-phase anaerobic digestion of vegetable market waste fraction of municipal solid waste and development of improved technology for phase separation in two-phase reactor.

    Science.gov (United States)

    Majhi, Bijoy Kumar; Jash, Tushar

    2016-12-01

    Biogas production from vegetable market waste (VMW) fraction of municipal solid waste (MSW) by two-phase anaerobic digestion system should be preferred over the single-stage reactors. This is because VMW undergoes rapid acidification leading to accumulation of volatile fatty acids and consequent low pH resulting in frequent failure of digesters. The weakest part in the two-phase anaerobic reactors was the techniques applied for solid-liquid phase separation of digestate in the first reactor where solubilization, hydrolysis and acidogenesis of solid organic waste occur. In this study, a two-phase reactor which consisted of a solid-phase reactor and a methane reactor was designed, built and operated with VMW fraction of Indian MSW. A robust type filter, which is unique in its implementation method, was developed and incorporated in the solid-phase reactor to separate the process liquid produced in the first reactor. Experiments were carried out to assess the long term performance of the two-phase reactor with respect to biogas production, volatile solids reduction, pH and number of occurrence of clogging in the filtering system or choking in the process liquid transfer line. The system performed well and was operated successfully without the occurrence of clogging or any other disruptions throughout. Biogas production of 0.86-0.889m(3)kg(-1)VS, at OLR of 1.11-1.585kgm(-3)d(-1), were obtained from vegetable market waste, which were higher than the results reported for similar substrates digested in two-phase reactors. The VS reduction was 82-86%. The two-phase anaerobic digestion system was demonstrated to be stable and suitable for the treatment of VMW fraction of MSW for energy generation. Copyright © 2016 Elsevier Ltd. All rights reserved.

  8. Facilitating Transfers

    DEFF Research Database (Denmark)

    Kjær, Poul F.

    to specific logics of temporalisation and spatial expansion of a diverse set of social processes in relation to, for example, the economy, politics, science and the mass media. On this background, the paper will more concretely develop a conceptual framework for classifying different contextual orders......The concept of governance has mutated into an all‐embracing buzz‐word characterised by a low degree of conceptual precision and empirical focus. This paper therefore suggests a narrower and more precise understanding of governance and the regulatory function it fulfils by advancing the argument...... that the essential functional and normative purpose of regulatory governance is to facilitate, stabilise and justify the transfer of condensed social components (such as economic capital and products, political decisions, legal judgements, religious beliefs and scientific knowledge) from one social contexts...

  9. Downward transfer of a sub-cooled cryoliquid

    CERN Document Server

    Wertelaers, P

    2016-01-01

    An alternative is proposed to the traditional transfer of a cryo fluid in gaseous -- and warm -- form, a method of low productivity and high energy cost. In order to prevent the much-feared geysering, focus is on sub-cooling of the liquid, and the safe maintaining of such state all along the journey. A cryogenic transfer line of simplest construction is proposed, and the difficulties with such line extending over a transfer depth of the order of the kilometre, are discussed.

  10. CFD modeling and experience of waste-to-energy plant burning waste wood

    DEFF Research Database (Denmark)

    Rajh, B.; Yin, Chungen; Samec, N.

    2013-01-01

    of waste wood combustion in a 13 MW grate-fired boiler in a WtE plant is presented. As a validation effort, the temperature profiles at a number of ports in the furnace are measured and the experimental results are compared with the CFD predictions. In the simulation, a 1D model is developed to simulate...... the conversion of the waste wood in the fuel bed on the grate, which provides the appropriate inlet boundary condition for the freeboard 3D CFD simulation. The CFD analysis reveals the detailed mixing and combustion characteristics in the waste wood-fired furnace, pinpointing how to improve the design......Computational Fluid Dynamics (CFD) is being increasingly used in industry for in-depth understanding of the fundamental mixing, combustion, heat transfer and pollutant formation in combustion processes and for design and optimization of Waste-to-Energy (WtE) plants. In this paper, CFD modeling...

  11. ASSESSMENT OF MEDICAL WASTE MANAGEMENT IN EDUCATIONAL HOSPITALS OF TEHRAN UNIVERSITY MEDICAL SCIENCES

    Directory of Open Access Journals (Sweden)

    M. H. Dehghani, K. Azam, F. Changani, E. Dehghani Fard

    2008-04-01

    Full Text Available The management of medical waste is of great importance due to its potential environmental hazards and public health risks. In the past, medical waste was often mixed with municipal solid waste and disposed in residential waste landfills or improper treatment facilities in Iran. In recent years, many efforts have been made by environmental regulatory agencies and waste generators to better managing the wastes from healthcare facilities. This study was carried in 12 educational hospitals of Tehran University of Medical Sciences. The goals of this study were to characterize solid wastes generated in healthcare hospitals, to report the current status of medical waste management and to provide a framework for the safe management of these wastes at the considered hospitals. The methodology was descriptive, cross-sectional and consisted of the use of surveys and interviews with the authorities of the healthcare facilities and with personnel involved in the management of the wastes. The results showed that medical wastes generated in hospitals were extremely heterogeneous in composition. 42% of wastes were collected in containers and plastic bags. In 75% of hospitals, the stay-time in storage sites was about 12-24h. 92% of medical wastes of hospitals were collected by covered-trucks. In 46% of hospitals, transferring of medical wastes to temporary stations was done manually. The average of waste generation rates in the hospitals was estimated to be 4.42kg/bed/day.

  12. Construction and Demolition Waste

    DEFF Research Database (Denmark)

    Christensen, Thomas Højlund; Andersen, L.

    2011-01-01

    Construction and demolition waste (C&D waste) is the waste generated during the building, repair, remodeling or removal of constructions. The constructions can be roads, residential housing and nonresidential buildings. C&D waste has traditionally been considered without any environmental problems...... and has just been landfilled. However, in recent years more focus has been put on C&D waste and data are starting to appear. One reason is that it has been recognized that C&D waste may include many materials that are contaminated either as part of their original design or through their use and therefore...... should be managed accordingly. Another reason is that it has been documented that a large fraction of C&D waste (about 90 %) can be easily recycled and thus can conserve landfill capacity. C&D waste may conveniently be divided into three subcategories: Buildings, roads and excavations. This chapter...

  13. Waste canister for storage of nuclear wastes

    Science.gov (United States)

    Duffy, James B.

    1977-01-01

    A waste canister for storage of nuclear wastes in the form of a solidified glass includes fins supported from the center with the tips of the fins spaced away from the wall to conduct heat away from the center without producing unacceptable hot spots in the canister wall.

  14. Business unusual - Waste Act implementation: solid waste

    CSIR Research Space (South Africa)

    Oelofse, Suzanna HH

    2013-08-01

    Full Text Available The preamble to the Waste Act (2008) is very clear that, as a result of this legislation, waste management in South Africa will never be the same again. This should send a clear message that ‘business as usual’ will no longer be sufficient....

  15. Structural Dimensions, Fabrication, Materials, and Operational History for Types I and II Waste Tanks

    Energy Technology Data Exchange (ETDEWEB)

    Wiersma, B.J.

    2000-08-16

    Radioactive waste is confined in 48 underground storage tanks at the Savannah River Site. The waste will eventually be processed and transferred to other site facilities for stabilization. Based on waste removal and processing schedules, many of the tanks, including those with flaws and/or defects, will be required to be in service for another 15 to 20 years. Until the waste is removed from storage, transferred, and processed, the materials and structures of the tanks must maintain a confinement function by providing a leak-tight barrier to the environment and by maintaining acceptable structural stability during design basis event which include loading from both normal service and abnormal conditions.

  16. Biohazardous waste management plan.

    Energy Technology Data Exchange (ETDEWEB)

    Lane, Todd W.

    2004-01-01

    This plan describes the process for managing non-medical biohazardous waste at Sandia National Laboratories California. It applies to operations at the Chemical and Radiation Detection Laboratory (CRDL), Building 968, and other biosafety level 1 or 2 activities at the site. It addresses the accumulation, storage, treatment and disposal of biohazardous waste and sharps waste. It also describes the procedures to comply with regulatory requirements and SNL policies applicable to non-medical biohazardous waste.

  17. Medical waste management plan.

    Energy Technology Data Exchange (ETDEWEB)

    Lane, Todd W.; VanderNoot, Victoria A.

    2004-12-01

    This plan describes the process for managing research generated medical waste at Sandia National Laboratories/California. It applies to operations at the Chemical and Radiation Detection Laboratory (CRDL), Building 968, and other biosafety level 1 or 2 activities at the site. It addresses the accumulation, storage, treatment and disposal of medical waste and sharps waste. It also describes the procedures to comply with regulatory requirements and SNL policies applicable to medical waste.

  18. INTEGRATED WASTE MANAGEMENT SYSTEM

    OpenAIRE

    Truptimala Patanaik; Ambika Priyadarshini Mishra; Aishariya Durga; Gayatri Avipsa

    2016-01-01

    The towns and cities have become the centres of population growth and require three essential services viz., water supply, waste water treatment and solid wastes disposal. The tremendous increase in population accelerates the amount of municipal solid waste (MSW) generation. Hence, the solid waste management (SWM) is one of the essential municipal services, to protect the environment, safeguard public health services and improve productivity.   In this context the case study is c...

  19. Solid waste handling

    Energy Technology Data Exchange (ETDEWEB)

    Parazin, R.J.

    1995-05-31

    This study presents estimates of the solid radioactive waste quantities that will be generated in the Separations, Low-Level Waste Vitrification and High-Level Waste Vitrification facilities, collectively called the Tank Waste Remediation System Treatment Complex, over the life of these facilities. This study then considers previous estimates from other 200 Area generators and compares alternative methods of handling (segregation, packaging, assaying, shipping, etc.).

  20. A review on organic waste to energy systems in India.

    Science.gov (United States)

    Dhar, Hiya; Kumar, Sunil; Kumar, Rakesh

    2017-12-01

    Waste generation is increasing day-by-day with the growth of population which directly affects the environment and economy. Organic municipal solid waste (MSW) and agriculture sectors contribute towards maximum waste generation in India. Thus, management of organic waste is very much essential with the increasing demand for energy. The present paper mainly focusses on reviewing waste to energy (WtE) potentials, its technologies, and the associated challenges. Different substrates are utilized through various technological options in India. Organic waste has good potential to attain sustainable energy yields with and without affecting the environment. A realistic scenario of WtE technologies and their challenges in line with the existing Indian condition is presented in this paper. Copyright © 2017 Elsevier Ltd. All rights reserved.

  1. Household food waste

    NARCIS (Netherlands)

    Wahlen, S.; Winkel, Thomas

    2017-01-01

    Food waste is debated not only in the light of sustainable consumption in research and policy, but also in the broader public. This article focuses on food waste in household contexts, what is widely believed the end of the food chain. However, household food waste is far more complex and intricate

  2. Nuclear wastes; Dechets nucleaires

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2004-07-01

    Here is made a general survey of the situation relative to radioactive wastes. The different kinds of radioactive wastes and the different way to store them are detailed. A comparative evaluation of the situation in France and in the world is made. The case of transport of radioactive wastes is tackled. (N.C.)

  3. Waste disposal package

    Science.gov (United States)

    Smith, M.J.

    1985-06-19

    This is a claim for a waste disposal package including an inner or primary canister for containing hazardous and/or radioactive wastes. The primary canister is encapsulated by an outer or secondary barrier formed of a porous ceramic material to control ingress of water to the canister and the release rate of wastes upon breach on the canister. 4 figs.

  4. Radioactive Wastes. Revised.

    Science.gov (United States)

    Fox, Charles H.

    This publication is one of a series of information booklets for the general public published by the United States Atomic Energy Commission. This booklet deals with the handling, processing and disposal of radioactive wastes. Among the topics discussed are: The Nature of Radioactive Wastes; Waste Management; and Research and Development. There are…

  5. Rock & Roll : Waste seperation

    NARCIS (Netherlands)

    Beunder, L.; Rem, P.C.; Van Den Berg, R.

    2000-01-01

    Five hundred tonnes of glass, 1 million tonnes of plastic,14 million tonnes of building and demolition waste, 7 million tonnes of household waste, 3 million tonnes of packaging, 3.5 million tonnes of paper and board, and 300,000 old cars. All part of the annual harvest of waste materials in the

  6. Waste vs Resource Management

    CSIR Research Space (South Africa)

    Oelofse, Suzanna HH

    2014-10-01

    Full Text Available Recent global waste statistics show that in the order of 70% of all municipal waste generated worldwide is disposed at landfill, 11% is treated in thermal and Waste-to-Energy (WtE) facilities and the rest (19%) is recycled or treated by mechanical...

  7. Toxicity assessment of carbon black waste: A by-product from oil refineries

    Energy Technology Data Exchange (ETDEWEB)

    Zhen, Xu; Ng, Wei Cheng [NUS Environmental Research Institute, National University of Singapore, 1 Create Way, Create Tower #15-02, 138602 (Singapore); Fendy; Tong, Yen Wah [Department of Chemical and Biomolecular Engineering, National University of Singapore, 4 Engineering Drive 4, 117585 (Singapore); Dai, Yanjun [School of Mechanical Engineering, Shanghai Jiaotong University, Shanghai, 200240 (China); Neoh, Koon Gee, E-mail: chenkg@nus.edu.sg [Department of Chemical and Biomolecular Engineering, National University of Singapore, 4 Engineering Drive 4, 117585 (Singapore); Wang, Chi-Hwa, E-mail: chewch@nus.edu.sg [Department of Chemical and Biomolecular Engineering, National University of Singapore, 4 Engineering Drive 4, 117585 (Singapore)

    2017-01-05

    Highlights: • Carbon black waste extract decreased cell viability in a dose and time-dependent manner. • Apoptosis of human cell lines was induced by carbon black waste extract. • Carbon black waste extract elicited oxidative stress by increasing intracellular ROS generation. • Carbon black waste extract impaired antioxidant enzymatic activities of human cell lines. • The high toxicity of carbon black waste extract could be attributed mainly to the effect of vanadium. - Abstract: In Singapore, approximately 30 t/day of carbon-based solid waste are produced from petrochemical processes. This carbon black waste has been shown to possess physical properties that are characteristic of a good adsorbent such as high external surface area. Therefore, there is a growing interest to reutilize and process this carbon black waste into secondary materials such as adsorbents. However, the carbon black waste obtained from petrochemical industries may contain heavy metals that are hazardous to human health and the environment, hence restricting its full potential for re-utilization. Therefore, it is important to examine the possible toxicity effects and toxicity mechanism of carbon black waste on human health. In this study, inductively coupled plasma optical emission spectroscopy (ICP-OES) analysis showed that the heavy metals, vanadium (V), molybdenum (Mo) and nickel (Ni), were present in the carbon black waste in high concentrations. Three human cell lines (HepG2 cells, MRC-5 cells and MDA-MB-231 cells) were used to investigate the toxicity of carbon black waste extract in a variety of in vitro assays. Results from MTS assays indicated that carbon black waste extract decreased the viability of all three cell lines in a dose and time-dependent manner. Observations from confocal microscopy further confirmed this phenomenon. Flow cytometry assay also showed that carbon black waste extract induced apoptosis of human cell lines, and the level of apoptosis increased with

  8. Funds transfer pricing in banking

    Directory of Open Access Journals (Sweden)

    Maria CARACOTA DIMITRIU

    2010-06-01

    Full Text Available Every bank needs to better understand the sources of its profitability. Whatever the size of the bank, funds transfer pricing (FTP can be used to help managing the bank's profitability by analyzing earnings for the whole institution or for different profit centers. In today’s banking environment, it is essential to look at the earnings both as a whole and broken down into various components. Funds Transfer Pricing is an analysis tool that can be used to help a bank measure its profitability in a variety of different ways. It allows management to compare the profitability of different product lines within the company, and it can be drilled down even further to allow comparison between individual employees. It is also very useful for comparison between branches. This study will reveal the role of Fund Transfer Pricing (FTP in banks.

  9. Management of radioactive waste packaging drum

    Energy Technology Data Exchange (ETDEWEB)

    Kang, Il-Sik; Shon, Kang J. S.; Lee, Y. H.; Song, I. T.; Lee, B. C.; Kim, K. J. [Korea Atomic Energy Research Institute, Taejeon (Korea)

    2000-02-01

    Radioactive waste drums of dismantled equipment and contaminated soil waste generated from KAERI research reactor, Seoul in 1988 were transferred to KAERI in Taejeon and are stored at low and medium level storage building until now. As a result of relatively long term storage, a corrosion on the surface of the drums was progressed and a remedial action was conducted to take a measure for the enhancement of safety. Thus, we examined the corrosion status on the surface of waste drums and studied mostly applicable methods. Resultingly, the seriously corroded drums were repackaged and the slightly corroded drums were painted after removing a corroded part on the surface. 12 refs., 14 figs., 12 tabs. (Author)

  10. Roadmap for disposal of Electrorefiner Salt as Transuranic Waste.

    Energy Technology Data Exchange (ETDEWEB)

    Rechard, Robert P. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Trone, Janis R. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Kalinina, Elena Arkadievna [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Wang, Yifeng [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Hadgu, Teklu [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Sanchez, Lawrence C. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2017-12-01

    The experimental breeder reactor (EBR-II) used fuel with a layer of sodium surrounding the uranium-zirconium fuel to improve heat transfer. Disposing of EBR-II fuel in a geologic repository without treatment is not prudent because of the potentially energetic reaction of the sodium with water. In 2000, the US Department of Energy (DOE) decided to treat the sodium-bonded fuel with an electrorefiner (ER), which produces metallic uranium product, a metallic waste, mostly from the cladding, and the salt waste in the ER, which contains most of the actinides and fission products. Two waste forms were proposed for disposal in a mined repository; the metallic waste, which was to be cast into ingots, and the ER salt waste, which was to be further treated to produce a ceramic waste form. However, alternative disposal pathways for metallic and salt waste streams may reduce the complexity. For example, performance assessments show that geologic repositories can easily accommodate the ER salt waste without treating it to form a ceramic waste form. Because EBR-II was used for atomic energy defense activities, the treated waste likely meets the definition of transuranic waste. Hence, disposal at the Waste Isolation Pilot Plant (WIPP) in southern New Mexico, may be feasible. This report reviews the direct disposal pathway for ER salt waste and describes eleven tasks necessary for implementing disposal at WIPP, provided space is available, DOE decides to use this alternative disposal pathway in an updated environmental impact statement, and the State of New Mexico grants permission.

  11. Mixed waste management options

    Energy Technology Data Exchange (ETDEWEB)

    Owens, C.B.; Kirner, N.P. [EG and G Idaho, Inc., Idaho Falls, ID (United States). Idaho National Engineering Lab.

    1991-12-31

    Disposal fees for mixed waste at proposed commercial disposal sites have been estimated to be $15,000 to $40,000 per cubit foot. If such high disposal fees are imposed, generators may be willing to apply extraordinary treatment or regulatory approaches to properly dispose of their mixed waste. This paper explores the feasibility of several waste management scenarios and attempts to answer the question: Can mixed waste be managed out of existence? Existing data on commercially generated mixed waste streams are used to identify the realm of mixed waste known to be generated. Each waste stream is evaluated from both a regulatory and technical perspective in order to convert the waste into a strictly low-level radioactive or a hazardous waste. Alternative regulatory approaches evaluated in this paper include a delisting petition, no migration petition, and a treatability variance. For each waste stream, potentially available treatment options are identified that could lead to these variances. Waste minimization methodology and storage for decay are also considered. Economic feasibility of each option is discussed broadly.

  12. Waste Management Technical Manual

    Energy Technology Data Exchange (ETDEWEB)

    Buckingham, J.S. [ed.

    1967-08-31

    This Manual has been prepared to provide a documented compendium of the technical bases and general physical features of Isochem Incorporated`s Waste Management Program. The manual is intended to be used as a means of training and as a reference handbook for use by personnel responsible for executing the Waste Management Program. The material in this manual was assembled by members of Isochem`s Chemical Processing Division, Battelle Northwest Laboratory, and Hanford Engineering Services between September 1965 and March 1967. The manual is divided into the following parts: Introduction, contains a summary of the overall Waste Management Program. It is written to provide the reader with a synoptic view and as an aid in understanding the subsequent parts; Feed Material, contains detailed discussion of the type and sources of feed material used in the Waste Management Program, including a chapter on nuclear reactions and the formation of fission products; Waste Fractionization Plant Processing, contains detailed discussions of the processes used in the Waste Fractionization Plant with supporting data and documentation of the technology employed; Waste Fractionization Plant Product and Waste Effluent Handling, contains detailed discussions of the methods of handling the product and waste material generated by the Waste Fractionization Plant; Plant and Equipment, describes the layout of the Waste Management facilities, arrangement of equipment, and individual equipment pieces; Process Control, describes the instruments and analytical methods used for process control; and Safety describes process hazards and the methods used to safeguard against them.

  13. Accumulation and subsequent utilization of waste heat

    Science.gov (United States)

    Koloničný, Jan; Richter, Aleš; Pavloková, Petra

    2016-06-01

    This article aims to introduce a special way of heat accumulation and primary operating characteristics. It is the unique way in which the waste heat from flue gas of biogas cogeneration station is stored in the system of storage tanks, into the heat transfer oil. Heat is subsequently transformed into water, from which is generated the low-pressure steam. Steam, at the time of peak electricity needs, spins the special designed turbine generator and produces electrical energy.

  14. Mixed waste: Proceedings

    Energy Technology Data Exchange (ETDEWEB)

    Moghissi, A.A.; Blauvelt, R.K.; Benda, G.A.; Rothermich, N.E. [eds.] [Temple Univ., Philadelphia, PA (United States). Dept. of Environmental Safety and Health

    1993-12-31

    This volume contains the peer-reviewed and edited versions of papers submitted for presentation a the Second International Mixed Waste Symposium. Following the tradition of the First International Mixed Waste Symposium, these proceedings were prepared in advance of the meeting for distribution to participants. The symposium was organized by the Mixed Waste Committee of the American Society of Mechanical Engineers. The topics discussed at the symposium include: stabilization technologies, alternative treatment technologies, regulatory issues, vitrification technologies, characterization of wastes, thermal technologies, laboratory and analytical issues, waste storage and disposal, organic treatment technologies, waste minimization, packaging and transportation, treatment of mercury contaminated wastes and bioprocessing, and environmental restoration. Individual abstracts are catalogued separately for the data base.

  15. Introduction to Waste Engineering

    DEFF Research Database (Denmark)

    Christensen, Thomas Højlund

    2011-01-01

    Solid waste management as introduced in Chapter 1.1 builds in many ways on engineering. Waste engineering here means the skills and ability to understand quantitatively how a waste management system works in such a detail that waste management can be planned, facilities can be designed and sited...... and systems can be operated in a way that is environmentally sound, technical feasible, economically efficient and socially acceptable. This applies to all scales of relevance: (1) national surveys of energy use and material flows determining the frame for politically setting goals in waste management, (2......) regional plans for waste management, including (3) the selection of main management technologies and siting of facilities, (4) the design of individual technological units and, for example, (5) the operation of recycling schemes within a municipality. This chapter gives an introduction to waste engineering...

  16. Mathematical model of subscriber extension line

    OpenAIRE

    Petříková, Iva; Diviš, Zdeněk; Tesař, Zdeněk

    2012-01-01

    The paper focuses on measurement properties of metallic subscriber extension lines to build regression mathematical model for a symmetric pair cable. The regression model is compared with an analytical model based on a theoretical description of transfer parameters for this type of line. The output of the paper should demonstrate the impact of electromagnetic interference on the symmetric pair. The paper also describes the method to identify the interference sources and ...

  17. Line Transport in Turbulent Atmospheres

    Science.gov (United States)

    Nikoghossian, A. G.

    2017-07-01

    The spectral line transfer in turbulent atmospheres with a spatially correlated velocity field is examined. Both the finite and semi-infinite media are treated. In finding the observed intensities we first deal with the problem for determining the mean intensity of radiation emerging from the medium for a fixed value of turbulent velocity at its boundary. A new approach proposed for solving this problem is based on the invariant imbedding technique which yields the solution of the proper problems for a family of media of different optical thicknesses and allows tackling different kinds of inhomogeneous problems. The dependence of the line profile, integral intensity, and the line width on the mean correlation length and the average value of the hydrodynamic velocity is studied. It is shown that the transition from a micro-turbulent regime to a macro-turbulence occurs within a comparatively narrow range of variation in the correlation length . Ambartsumian's principle of invariance is used to solve the problem of diffuse reflection of the line radiation from a one-dimensional semi-infinite turbulent atmosphere. In addition to the observed spectral line profile, statistical averages describing the diffusion process in the atmosphere (mean number of scattering events, average time spent by a diffusing photon in the medium) are determined. The dependence of these quantities on the average hydrodynamic velocity and correlation coefficient is studied.

  18. Indirect Determination of Chemical Composition and Fuel Characteristics of Solid Waste

    DEFF Research Database (Denmark)

    Riber, Christian; Christensen, Thomas Højlund

    Determination of chemical composition of solid waste can be performed directly or indirectly by analysis of combustion products. The indirect methodology instrumented by a full scale incinerator is the only method that can conclude on elements in trace concentrations. These elements are of great...... interest in evaluating waste management options by for example LCA modeling. A methodology description of indirect determination of chemical composition and fuel properties of waste is provided and validated by examples. Indirect analysis of different waste types shows that the chemical composition...... is significantly dependent on waste type. And the analysis concludes that the transfer of substances in the incinerator is a function of waste chemical content, incinerator technology and waste physical properties. The importance of correct representation of rare items in the waste with high concentrations...

  19. Process Knowledge Summary Report for Materials and Fuels Complex Contact-Handled Transuranic Debris Waste

    Energy Technology Data Exchange (ETDEWEB)

    R. P. Grant; P. J. Crane; S. Butler; M. A. Henry

    2010-02-01

    This Process Knowledge Summary Report summarizes the information collected to satisfy the transportation and waste acceptance requirements for the transfer of transuranic (TRU) waste between the Materials and Fuels Complex (MFC) and the Advanced Mixed Waste Treatment Project (AMWTP). The information collected includes documentation that addresses the requirements for AMWTP and the applicable portion of their Resource Conservation and Recovery Act permits for receipt and treatment of TRU debris waste in AMWTP. This report has been prepared for contact-handled TRU debris waste generated by the Idaho National Laboratory at MFC. The TRU debris waste will be shipped to AMWTP for purposes of supercompaction. This Process Knowledge Summary Report includes information regarding, but not limited to, the generation process, the physical form, radiological characteristics, and chemical contaminants of the TRU debris waste, prohibited items, and packaging configuration. This report, along with the referenced supporting documents, will create a defensible and auditable record for waste originating from MFC.

  20. Independent engineering review of the Hanford Waste Vitrification System

    Energy Technology Data Exchange (ETDEWEB)

    1991-10-01

    The Hanford Waste Vitrification Plant (HWVP) was initiated in June 1987. The HWVP is an essential element of the plan to end present interim storage practices for defense wastes and to provide for permanent disposal. The project start was justified, in part, on efficient technology and design information transfer from the prototype Defense Waste Processing Facility (DWPF). Development of other serial Hanford Waste Vitrification System (HWVS) elements, such as the waste retrieval system for the double-shell tanks (DSTs), and the pretreatment system to reduce the waste volume converted into glass, also was required to accomplish permanent waste disposal. In July 1991, at the time of this review, the HWVP was in the Title 2 design phase. The objective of this technical assessment is to determine whether the status of the technology development and engineering practice is sufficient to provide reasonable assurance that the HWVP and the balance of the HWVS system will operate in an efficient and cost-effective manner. The criteria used to facilitate a judgment of potential successful operation are: vitrification of high-level radioactive waste from specified DSTs on a reasonably continuous basis; and glass produced with physical and chemical properties formally acknowledge as being acceptable for disposal in a repository for high-level radioactive waste. The criteria were proposed specifically for the Independent Engineering Review to focus that assessment effort. They are not represented as the criteria by which the Department will judge the prudence of the Project. 78 refs., 10 figs., 12 tabs.

  1. Tank Waste Remediation System fiscal year 1996 multi-year program plan WBS 1.1. Revision 1, Appendix A

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-09-01

    This document is a compilation of data relating to the Tank Waste Remediation System Multi-Year Program. Topics discussed include: management systems; waste volume, transfer and evaporation management; transition of 200 East and West areas; ferricyanide, volatile organic vapor, and flammable gas management; waste characterization; retrieval from SSTs and DSTs; heat management; interim storage; low-level and high-level radioactive waste management; and tank farm closure.

  2. Cleaning Up Electronic Waste (E-Waste)

    Science.gov (United States)

    While accurate data on the amount of e-waste being exported from the U.S. are not available, the United States government is concerned that these exports are being mismanaged abroad, causing serious public health and environmental hazards.

  3. Guidelines for generators of hazardous chemical waste at LBL and guidelines for generators of radioactive and mixed waste at LBL. Revision 1

    Energy Technology Data Exchange (ETDEWEB)

    1991-09-01

    In part one of this document the Governing Documents and Definitions sections provide general guidelines and regulations applying to the handling of hazardous chemical wastes. The remaining sections provide details on how you can prepare your waste properly for transport and disposal. They are correlated with the steps you must take to properly prepare your waste for pickup. The purpose of the second part of this document is to provide the acceptance criteria for the transfer of radioactive and mixed waste to LBL`s Hazardous Waste Handling Facility (HWHF). These guidelines describe how you, as a generator of radioactive or mixed waste, can meet LBL`s acceptance criteria for radioactive and mixed waste.

  4. TSA waste stream and final waste form composition

    Energy Technology Data Exchange (ETDEWEB)

    Grandy, J.D.; Eddy, T.L.; Anderson, G.L.

    1993-01-01

    A final vitrified waste form composition, based upon the chemical compositions of the input waste streams, is recommended for the transuranic-contaminated waste stored at the Transuranic Storage Area of the Radioactive Waste Management Complex at the Idaho National Engineering Laboratory. The quantities of waste are large with a considerable uncertainty in the distribution of various waste materials. It is therefore impractical to mix the input waste streams into an ``average`` transuranic-contaminated waste. As a result, waste stream input to a melter could vary widely in composition, with the potential of affecting the composition and properties of the final waste form. This work examines the extent of the variation in the input waste streams, as well as the final waste form under conditions of adding different amounts of soil. Five prominent Rocky Flats Plant 740 waste streams are considered, as well as nonspecial metals and the ``average`` transuranic-contaminated waste streams. The metals waste stream is the most extreme variation and results indicate that if an average of approximately 60 wt% of the mixture is soil, the final waste form will be predominantly silica, alumina, alkaline earth oxides, and iron oxide. This composition will have consistent properties in the final waste form, including high leach resistance, irrespective of the variation in waste stream. For other waste streams, much less or no soil could be required to yield a leach resistant waste form but with varying properties.

  5. Los Alamos Transuranic Waste Size Reduction Facility

    Energy Technology Data Exchange (ETDEWEB)

    Harper, J.; Warren, J.

    1987-06-01

    The Los Alamos Transuranic (TRU) Waste Size Reduction Facility (SRF) is a production oriented prototype. The facility is operated to remotely cut and repackage TRU contaminated metallic wastes (e.g., glove boxes, ducting and pipes) for eventual disposal at the Waste Isolation Pilot Plant (WIPP) near Carlsbad, New Mexico. The resulting flat sections are packaged into a tested Department of Transportation Type 7A metal container. To date, the facility has successfully processed stainless steel glove boxes (with and without lead shielding construction) and retention tanks. We have found that used glove boxes generate more cutting fumes than do unused glove boxes or metal plates - possibly due to deeply embedded chemical residues from years of service. Water used as a secondary fluid with the plasma arc cutting system significantly reduces visible fume generation during the cutting of used glove boxes and lead-lined glove boxes. 2 figs., 1 tab.

  6. Solid Waste Management Plan. Revision 4

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-04-26

    The waste types discussed in this Solid Waste Management Plan are Municipal Solid Waste, Hazardous Waste, Low-Level Mixed Waste, Low-Level Radioactive Waste, and Transuranic Waste. The plan describes for each type of solid waste, the existing waste management facilities, the issues, and the assumptions used to develop the current management plan.

  7. Factors governing particle number emissions in a waste-to-energy plant.

    Science.gov (United States)

    Ozgen, Senem; Cernuschi, Stefano; Giugliano, Michele

    2015-05-01

    Particle number concentration and size distribution measurements were performed on the stack gas of a waste-to-energy plant which co-incinerates municipal solid waste, sewage sludge and clinical waste in two lines. Average total number of particles was found to be 4.0·10(5)cm(-3) and 1.9·10(5)cm(-3) for the line equipped with a wet flue gas cleaning process and a dry cleaning system, respectively. Ultrafine particles (dpwaste feed and the municipal solid waste co-incineration with sludge. Copyright © 2015 Elsevier Ltd. All rights reserved.

  8. Plan of SPS to LHC transfer tunnels

    CERN Multimedia

    Laurent Guiraud

    2001-01-01

    This diagram shows the LHC and the SPS pre-accelerator (in blue) and the transfer lines that will connect them (in red). Spanning the France-Swiss border (shown by green crosses), the 27-km LHC tunnel will receive a beam that has been pre-accelerated to 450 GeV in the smaller SPS storage ring. The transfer lines will remove each beam from the SPS and inject them into the LHC where they will be accelerated to the full energy of 7 TeV.

  9. Soil Pollution by Toxic Metals near E-waste Recycling Operations in Ibadan, Nigeria

    National Research Council Canada - National Science Library

    Adesokan, Michael D; Adie, Gilbert U; Osibanjo, Oladele

    2016-01-01

    Background. Unsound recycling of e-waste releases toxic metals into environmental media and has deleterious health consequences to humans as the metals transfer to humans through the food chain, direct contact and inhalation. Objectives...

  10. Waste statistics 2004

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2006-04-07

    The 2004 reporting to the ISAG comprises 394 plants owned by 256 enterprises. In 2003, reports covered 403 plants owned by 273 enterprises. Waste generation in 2004 is compared to targets for 2008 in the government's Waste Strategy 2005-2008. The following summarises waste generation in 2004: 1) In 2004, total reported waste arisings amounted to 13,359,000 tonnes, which is 745,000 tonnes, or 6 per cent, more than in 2003. 2) If amounts of residues from coal-fired power plants are excluded from statistics, waste arisings in 2004 were 12,179,000 tonnes, which is a 9 per cent increase from 2003. 3) If amounts of residues from coal-fired power plants and waste from the building and construction sector are excluded from statistics, total waste generation in 2004 amounted to 7,684,000 tonnes, which is 328,000 tonnes, or 4 per cent, more than in 2002. In other words, there has been an increase in total waste arisings, if residues and waste from building and construction are excluded. Waste from the building and construction sector is more sensitive to economic change than most other waste. 4) The total rate of recycling was 65 per cent. The 2008 target for recycling is 65 per cent. The rate of recycling in 2003 was also 65 per cent. 5) The total amount of waste led to incineration amounted to 26 per cent, plus an additional 1 per cent left in temporary storage to be incinerated at a later time. The 2008 target for incineration is 26 per cent. These are the same percentage figures as applied to incineration and storage in 2003. 6) The total amount of waste led to landfills amounted to 8 per cent, which is one percentage point better than the overall landfill target of a maximum of 9 per cent landfilling in 2008. Also in 2003, 8 per cent of the waste was landfilled. 7) The targets for treatment of waste from individual sectors are still not being met: too little waste from households and the service sector is being recycled, and too much waste from industry is being

  11. Disposal and degradation of pesticide waste.

    Science.gov (United States)

    Felsot, Allan S; Racke, Kenneth D; Hamilton, Denis J

    2003-01-01

    Generation of pesticide waste is inevitable during every agricultural operation from storage to use and equipment cleanup. Large-scale pesticide manufacturers can afford sophisticated recovery, treatment, and cleanup techniques. Small-scale pesticide users, for example, single farms or small application businesses, struggle with both past waste problems, including contaminated soils, and disposal of unused product and equipment rinsewater. Many of these problems have arisen as a result of inability to properly handle spills during, equipment loading and rinsewater generated after application. Small-scale facilities also face continued problems of wastewater handling. Old, obsolete pesticide stocks are a vexing problem in numerous developing countries. Pesticide waste is characterized by high concentrations of a diversity of chemicals and associated adjuvants. Dissipation of chemicals at elevated concentrations is much slower than at lower concentrations, in part because of microbial toxicity and mass transfer limitations. High concentrations of pesticides may also move faster to lower soil depths, especially when pore water becomes saturated wish a compound. Thus, if pesticide waste is not properly disposed of, groundwater and surface water contamination become probable. The Waste Management Hierarchy developed as an Australian Code of Practice can serve as a guide for development of a sound waste management plan. In order of desirability, the course of actions include waste avoidance, waste reduction, waste recycling, waste treatment, and waste disposal. Proper management of pesticide stocks, including adequate storage conditions, good inventory practices, and regular turnover of products,. will contribute to waste avoidance and reduction over the long-term. Farmers can also choose to use registered materials that have the lowest recommended application rates or are applied in the least volume of water. Wastewater that is generated during equipment rinsing can be

  12. Peripheral intravenous line - infants

    Science.gov (United States)

    PIV - infants; Peripheral IV - infants; Peripheral line - infants; Peripheral line - neonatal ... A peripheral intravenous line (PIV) is a small, short, plastic tube, called a catheter. A health care provider puts the PIV through the ...

  13. Sewer Main Pipe Lines

    Data.gov (United States)

    U.S. Environmental Protection Agency — This is a line feature dataset with lines across the island of Guam. These lines represent the sewer mains that carry refuse to the sewer plants for processing and...

  14. Beam transfer to and Injection into LHC

    CERN Document Server

    Hilaire, A; Weisse, E

    1998-01-01

    Transfer of 450 GeV protons from SPS to LHC will be carried out through two new beam transfer lines with a length of about 2.8-km per line. One beam will use the existing SPS west extraction in LSS6 from where a new line will lead to the LHC injection near intersection 2. A new fast extraction facility in SPS LSS4 is needed for the other beam line which will lead to LHC intersection 8. Economy considerations have led to the decision to use classical magnets of compact design. A lot of components will be recuperated from closed down installations. The injection systems consist of horizontally deflecting Lambertson type septum magnets and vertically deflecting kickers. A careful control of the trajectory and the preservation of the very small emittance during transfer and injection are of key importance. Construction for the transfer lines will start in 1998 to allow first injection tests in 2003. The report describes the layout and optics design and the required performance of the main components.

  15. Computational Fluid Dynamics Modeling of Bubbling in a Viscous Fluid for Validation of Waste Glass Melter Modeling

    Energy Technology Data Exchange (ETDEWEB)

    Abboud, Alexander William [Idaho National Laboratory; Guillen, Donna Post [Idaho National Laboratory

    2016-01-01

    At the Hanford site, radioactive waste stored in underground tanks is slated for vitrification for final disposal. A comprehensive knowledge of the glass batch melting process will be useful in optimizing the process, which could potentially reduce the cost and duration of this multi-billion dollar cleanup effort. We are developing a high-fidelity heat transfer model of a Joule-heated ceramic lined melter to improve the understanding of the complex, inter-related processes occurring with the melter. The glass conversion rates in the cold cap layer are dependent on promoting efficient heat transfer. In practice, heat transfer is augmented by inserting air bubblers into the molten glass. However, the computational simulations must be validated to provide confidence in the solutions. As part of a larger validation procedure, it is beneficial to split the physics of the melter into smaller systems to validate individually. The substitution of molten glass for a simulant liquid with similar density and viscosity at room temperature provides a way to study mixing through bubbling as an isolated effect without considering the heat transfer dynamics. The simulation results are compared to experimental data obtained by the Vitreous State Laboratory at the Catholic University of America using bubblers placed within a large acrylic tank that is similar in scale to a pilot glass waste melter. Comparisons are made for surface area of the rising air bubbles between experiments and CFD simulations for a variety of air flow rates and bubble injection depths. Also, computed bubble rise velocity is compared to a well-accepted expression for bubble terminal velocity.

  16. Ceramics in nuclear waste management

    Energy Technology Data Exchange (ETDEWEB)

    Chikalla, T D; Mendel, J E [eds.

    1979-05-01

    Seventy-three papers are included, arranged under the following section headings: national programs for the disposal of radioactive wastes, waste from stability and characterization, glass processing, ceramic processing, ceramic and glass processing, leaching of waste materials, properties of nuclear waste forms, and immobilization of special radioactive wastes. Separate abstracts were prepared for all the papers. (DLC)

  17. Evaluation of 1985--1986 corrective actions at ORNL liquid waste disposal trench 7

    Energy Technology Data Exchange (ETDEWEB)

    Spalding, B.P.

    1991-04-01

    Several corrective actions were taken in 1985--1986 at the site of ORNL radioactive liquid waste seepage trench 7 in an effort to reduce the discharge of radionuclides, mostly {sup 60}Co, from a groundwater seep on the eastern side of the site. First, the size of the asphalt cap over the trench was doubled, and cap runoff was diverted away from the site to the west. Second, the buried waste transfer line to the trench was excavated and plugged and its pipe trench was damned with clay backfill. These actions were designed to reduce groundwater recharge in the area that might be the source of water to the seep. Third, a series of grout injections was carried out at 5-ft intervals along a perimeter line on the eastern and northern edges of the site. A total of 65,500 gal of lime-fly-ash grout was injected at 303 locations at depths up to 40 ft in an effort to seal relict contaminated strata with probable hydrologic connection to the seep. However, the grout formulation specified in the contract would not set to a detectable compressive strength nor would the grout samples exhibit a reduction in hydraulic conductivity during over a year of observation. Thus, the material specification for the grout was inappropriate for the desired effect of in situ hydrologic isolation. Core sampling at the site revealed that the grout flowed into the soil formation along discrete thin layers. Only three grout layers, with a maximum thickness of 0.25 in., were found in over 90 ft of core from three locations along the grout injection line. Thus, this grouting action would have little potential to influence containment of radionuclides that leach from contaminated strata. 11 refs., 14 figs., 7 tabs.

  18. WTP Waste Feed Qualification: Glass Fabrication Unit Operation Testing Report

    Energy Technology Data Exchange (ETDEWEB)

    Stone, M. E. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL). Hanford Missions Programs; Newell, J. D. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL). Process Technology Programs; Johnson, F. C. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL). Engineering Process Development; Edwards, T. B. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL). Engineering Process Development

    2016-07-14

    The waste feed qualification program is being developed to protect the Hanford Tank Waste Treatment and Immobilization Plant (WTP) design, safety basis, and technical basis by assuring waste acceptance requirements are met for each staged waste feed campaign prior to transfer from the Tank Operations Contractor to the feed receipt vessels inside the Pretreatment Facility. The Waste Feed Qualification Program Plan describes the three components of waste feed qualification: 1. Demonstrate compliance with the waste acceptance criteria 2. Determine waste processability 3. Test unit operations at laboratory scale. The glass fabrication unit operation is the final step in the process demonstration portion of the waste feed qualification process. This unit operation generally consists of combining each of the waste feed streams (high-level waste (HLW) and low-activity waste (LAW)) with Glass Forming Chemicals (GFCs), fabricating glass coupons, performing chemical composition analysis before and after glass fabrication, measuring hydrogen generation rate either before or after glass former addition, measuring rheological properties before and after glass former addition, and visual observation of the resulting glass coupons. Critical aspects of this unit operation are mixing and sampling of the waste and melter feeds to ensure representative samples are obtained as well as ensuring the fabrication process for the glass coupon is adequate. Testing was performed using a range of simulants (LAW and HLW simulants), and these simulants were mixed with high and low bounding amounts of GFCs to evaluate the mixing, sampling, and glass preparation steps in shielded cells using laboratory techniques. The tests were performed with off-the-shelf equipment at the Savannah River National Laboratory (SRNL) that is similar to equipment used in the SRNL work during qualification of waste feed for the Defense Waste Processing Facility (DWPF) and other waste treatment facilities at the

  19. Disposal of waste channels and control rods and radioactive waste; Gestion de canales usados y barras de control como residuos radiactivos

    Energy Technology Data Exchange (ETDEWEB)

    Lopez Alvarez, L.

    2015-07-01

    Iberdrola and ENRESA are jointly developing a project for the characterization and conditioning of around 200 control rods and 70 used channel from Cofrentes Nuclear Power Plant. This treatment line for high level waste with a radiologic inventory that avoids using the El Cabril low level waste repository is new in Spain and incorporates specific features like the option to carry on with the conditioning stage prior to having a licensed package and available storage facility for this type of waste. (Author)

  20. EVo: Net Shape RTM Production Line

    OpenAIRE

    Sven Torstrick; Felix Kruse; Martin Wiedemann

    2016-01-01

    EVo research platform is operated by the Center for Lightweight-Production-Technology of the German Aerospace Center in Stade. Its objective is technology demonstration of a fully automated RTM (Resin Transfer Molding) production line for composite parts in large quantities. Process steps include cutting and ply handling, draping, stacking, hot-forming, preform-trimming to net shape, resin injection, curing and demolding.