WorldWideScience

Sample records for waste releases startup

  1. PCDD/F emissions during startup and shutdown of a hazardous waste incinerator.

    Science.gov (United States)

    Li, Min; Wang, Chao; Cen, Kefa; Ni, Mingjiang; Li, Xiaodong

    2017-08-01

    Compared with municipal solid waste incineration, studies on the PCDD/F emissions of hazardous waste incineration (HWI) under transient conditions are rather few. This study investigates the PCDD/F emission level, congener profile and removal efficiency recorded during startup and shutdown by collecting flue gas samples at the bag filter inlet and outlet and at the stack. The PCDD/F concentration measured in the stack gas during startup and shutdown were 0.56-4.16 ng I-TEQ Nm(-3) and 1.09-3.36 ng I-TEQ Nm(-3), respectively, far exceeding the present codes in China. The total amount of PCDD/F emissions, resulting from three shutdown-startup cycles of this HWI-unit is almost equal to that generated during one year under normal operating conditions. Upstream the filter, the PCDD/F in the flue gas is mainly in the particle phase; however, after being filtered PCDD/F prevails in the gas phase. The PCDD/F fraction in the gas phase even exceeds 98% after passing through the alkaline scrubber. Especially higher chlorinated PCDD/F accumulate on inner walls of filters and ducts during these startup periods and could be released again during normal operation, significantly increasing PCDD/F emissions. Copyright © 2017. Published by Elsevier Ltd.

  2. Checkout and start-up of the integrated DWPF (Defense Waste Processing Facility) melter system

    Energy Technology Data Exchange (ETDEWEB)

    Smith, M.E.; Hutson, N.D.; Miller, D.H.; Morrison, J.; Shah, H.; Shuford, J.A.; Glascock, J.; Wurzinger, F.H.; Zamecnik, J.R.

    1989-11-11

    The Integrated DWPF Melter System (IDMS) is a one-ninth-scale demonstration of the Defense Waste Processing Facility (DWPF) feed preparation, melter, and off-gas systems. The IDMS will be the first engineering-scale melter system at SRL to process mercury and flowsheet levels of halides and sulfates. This report includes a summary of the IDMS program objectives, system and equipment descriptions, and detailed discussions of the system checkout and start-up. 10 refs., 44 figs., 20 tabs.

  3. Argonne National Laboratory`s photo-oxidation organic mixed waste treatment system - installation and startup testing

    Energy Technology Data Exchange (ETDEWEB)

    Shearer, T.L.; Nelson, R.A.; Torres, T.; Conner, C.; Wygmans, D.

    1997-09-01

    This paper describes the installation and startup testing of the Argonne National Laboratory (ANL-E) Photo-Oxidation Organic Mixed Waste Treatment System. This system will treat organic mixed (i.e., radioactive and hazardous) waste by oxidizing the organics to carbon dioxide and inorganic salts in an aqueous media. The residue will be treated in the existing radwaste evaporators. The system is installed in the Waste Management Facility at the ANL-E site in Argonne, Illinois. 1 fig.

  4. Start-up performances of dry anaerobic mesophilic and thermophilic digestions of organic solid wastes

    Institute of Scientific and Technical Information of China (English)

    LU Shu-guang; IMAI Tsuyoshi; UKITA Masao; SEKINE Masahiko

    2007-01-01

    Two dry anaerobic digestions of organic solid wastes were conducted for 6 weeks in a lab-scale batch experiment for investigating the start-up performances under mesophilic and thermophilic conditions. The enzymatic activities,i.e., β-glucosidase, β-glucosidase, N-α -benzoyl-L-argininamide (BAA)-hydrolysing protease, urease and phosphatase activities were analysed. The lower BAA-hydrolysing protease activity during the first 2-3 weeks was due to the inhibition of the low pH, but was enhanced simultaneously later with the pH increase. β-glucosidase activity showed the lowest values in weeks 1-2, and recovered simultaneously with the increase of BAA-hydrolysing protease activity. Acetic acid dominated most of the total VFAs in thermophilic digestion, while propionate and butyrate dominated in mesophilic digestion. Thermophilic digestion is confirmed more feasible for achieving better performance against misbalance, especially during the start-up period in a dry anaerobic digestion process.

  5. Adaption of microbial community during the start-up stage of a thermophilic anaerobic digester treating food waste.

    Science.gov (United States)

    Wu, Bo; Wang, Xing; Deng, Ya-Yue; He, Xiao-Lan; Li, Zheng-Wei; Li, Qiang; Qin, Han; Chen, Jing-Tao; He, Ming-Xiong; Zhang, Min; Hu, Guo-Quan; Yin, Xiao-Bo

    2016-10-01

    A successful start-up enables acceleration of anaerobic digestion (AD) into steady state. The microbial community influences the AD performance during the start-up. To investigate how microbial communities changed during the start-up, microbial dynamics was analyzed via high-throughput sequencing in this study. The results confirmed that the AD was started up within 25 d. Thermophilic methanogens and bacterial members functioning in hydrolysis, acidogenesis, and syntrophic oxidation became predominant during the start-up stage, reflecting a quick adaption of microorganisms to operating conditions. Such predominance also indicated the great contribution of these members to the fast start-up of AD. Redundancy analysis confirmed that the bacterial abundance significantly correlated with AD conditions. The stable ratio of hydrogenotrophic methanogens to aceticlastic methanogens is also important to maintain the stability of the AD process. This work will be helpful to understand the contribution of microbial community to the start-up of AD.

  6. Removal of diclofenac and sulfamethoxazole from synthetic municipal waste water in microcosm downflow constructed wetlands: Start-up results.

    Science.gov (United States)

    Nowrotek, Monika; Sochacki, Adam; Felis, Ewa; Miksch, Korneliusz

    2016-01-01

    The objectives of this study were to investigate the start-up removal of pharmaceutical compounds diclofenac and sulfamethoxazole in microcosm downflow constructed wetlands and their effect on the performance of the studied constructed wetlands, and also to assess the effect of plants on the removal of these compounds. The experimental system that was used in this 86-day experiment consisted of 24 columns filled up to 70 cm with predominantly sandy material. Four types of columns were used (six replicates) depending on the presence of plants (Phalaris arundinacea L. var. picta L.) and the presence of pharmaceutical compounds in the influent. The influent was synthetic municipal waste water to which a mixture of 5 mg/L of diclofenac and 5 mg/L of sulfamethoxazole was added. The observed removal of diclofenac was moderate (approx. 50%) and the removal of sulfamethoxazole was relatively low (24-30%). It was found that the removal of diclofenac and sulfamethoxazole was not affected by the vegetation. The presence of diclofenac and sulfamethoxazole in the influent had significant effect on the effluent concentration of N-NO3 and the water loss in the columns, which in both cases were lower than in the control columns. The scope for further research was discussed.

  7. DOE final report, phase one startup, Waste Receiving and Processing Facility (WRAP)

    Energy Technology Data Exchange (ETDEWEB)

    Jasen, W.G.

    1998-01-07

    This document is to validate that the WRAP facility is physically ready to start up phase 1, and that the managers and operators are prepared to safely manage and operate the facility when all pre-start findings have been satisfactorily corrected. The DOE Readiness Assessment (RA) team spent a week on-site at Waste Receiving and Processing Module 1 (WRAP-1) to validate the readiness for phase 1 start up of facility. The Contractor and DOE staff were exceptionally cooperative and contributed significantly to the overall success of the RA. The procedures and Conduct of Operations areas had significant discrepancies, many of which should have been found by the contractor review team. In addition the findings of the contractor review team should have led the WRAP-1 management team to correcting the root causes of the findings prior to the DOE RA team review. The findings and observations include many issues that the team believes should have been found by the contractor review and corrective actions taken. A significantly improved Operational Readiness Review (ORR) process and corrective actions of root causes must be fully implemented by the contractor prior to the performance of the contractor ORR for phase 2 operations. The pre-start findings as a result of this independent DOE Readiness Assessment are presented.

  8. Microbial population dynamics during startup of a full-scale anaerobic digester treating industrial food waste in Kyoto eco-energy project.

    Science.gov (United States)

    Ike, Michihiko; Inoue, Daisuke; Miyano, Tomoki; Liu, Tong Tong; Sei, Kazunari; Soda, Satoshi; Kadoshin, Shiro

    2010-06-01

    The microbial community in a full-scale anaerobic digester (2300m3) treating industrial food waste in the Kyoto Eco-Energy Project was analyzed using terminal restriction fragment length polymorphism for eubacterial and archaeal 16S rRNA genes. Both thermophilic and mesophilic sludge of treated swine waste were seeded to the digestion tank. During the 150-day startup period, coffee grounds as a main food waste, along with potato, kelp and boiled beans, tofu, bean curd lees, and deep-fried bean curd were fed to the digestion process step-by-step (max. 40t/d). Finally, the methane yield reached 360m3/t-feed with 40days' retention time, although temporary accumulation of propionate was observed. Eubacterial communities that formed in the thermophilic digestion tank differed greatly from both thermophilic and mesophilic types of seed sludge. Results suggest that the Actinomyces/Thermomonospora and Ralstonia/Shewanella were contributors for hydrolyzation and degradation of food waste into volatile fatty acids. Acetate-utilizing methanogens, Methanosaeta, were dominant in seed sludges of both types, but they decreased drastically during processing in the digestion tank. Methanosarcina and Methanobrevibacter/Methanobacterium were, respectively, possible main contributors for methane production from acetate and H2 plus CO2. Copyright 2010 Elsevier Ltd. All rights reserved.

  9. Effects of Globally Waste Disturbing Activities on Gas Generation, Retention, and Release in Hanford Waste Tanks

    Energy Technology Data Exchange (ETDEWEB)

    Stewart, Charles W.; Fountain, Matthew S.; Huckaby, James L.; Mahoney, Lenna A.; Meyer, Perry A.; Wells, Beric E.

    2005-08-02

    Various operations are authorized in Hanford single- and double-shell tanks that disturb all or a large fraction of the waste. These globally waste-disturbing activities have the potential to release a large fraction of the retained flammable gas and to affect future gas generation, retention, and release behavior. This report presents analyses of the expected flammable gas release mechanisms and the potential release rates and volumes resulting from these activities. The background of the flammable gas safety issue at Hanford is summarized, as is the current understanding of gas generation, retention, and release phenomena. Considerations for gas monitoring and assessment of the potential for changes in tank classification and steady-state flammability are given.

  10. Preventing Buoyant Displacement Gas Release Events in Hanford Double-Shell Waste Tanks

    Energy Technology Data Exchange (ETDEWEB)

    Meyer, Perry A.; Stewart, Charles W.

    2001-01-01

    This report summarizes the predictive methods used to ensure that waste transfer operations in Hanford waste tanks do not create waste configurations that lead to unsafe gas release events. The gas release behavior of the waste in existing double-shell tanks has been well characterized, and the flammable gas safety issues associated with safe storage of waste in the current configuration are being formally resolved. However, waste is also being transferred between double-shell tanks and from single-shell tanks into double-shell tanks by saltwell pumping and sluicing that create new wastes and waste configurations that have not been studied as well. Additionally, planning is underway for various waste transfer scenarios to support waste feed delivery to the proposed vitrification plant. It is critical that such waste transfers do not create waste conditions with the potential for dangerous gas release events.

  11. Start-up of a multi-stage system for biogas production and solid waste treatment in low-tech countries

    Energy Technology Data Exchange (ETDEWEB)

    Biey, E.M.; Musibono, E.D. [University of Kinshasa (Congo). Laboratory of Ecotoxicology and Environmental Science and Technology, VLICO Project; Verstraete, W. [Laboratory of Microbial Ecology and Technology, Gent (Belgium)

    2003-07-01

    Vegetable fruit garden wastes were treated anaerobically using a multistage Dranco system. The digesters were composed of three 50 L vessels kept in mesophilic conditions. They were operating at 14.5-17% TS. By controlling the pH in the system, the start-up for biogas production was shortened to 60 days. The pH correction was a buffering which enhanced methanogenic activity in the digesters. With a loading rate of 4.1 kg VS/m{sup 3}reactor.day, the production of biogas was 5 m{sup 3}/m{sup 3}reactor.day, and 60-70% methane content. This allowed making a multisystem by starting every 3 weeks with new vessels in order to maintain biogas production, to be used in industries or in local communities in low-tech countries. The designed model was started in Kinshasa (Congo) where a project is expected to treat one ton of solid waste on a daily basis, for a production of 100 m{sup 3} biogas. This cost effectiveness of the system is demonstrated and presents the opportunity for biowaste treatment coupled with environmental protection and substantial energy recovery. (author)

  12. Improvement of waste release control in French NPP

    Energy Technology Data Exchange (ETDEWEB)

    Samson, T.; Lucquin, E.; Dupin, M. [EDF/GDL (France); Florence, D. [EDF/GENV (France); Grisot, M. [EDF/CNPE Saint Laurent (France)

    2002-07-01

    The new waste release control in French NPP is more restrictive than the old one and needs heavy investment to bring plants to compliance with it. The great evolutions are a chemical follow up on more chemicals with a higher measurement frequency and with lower maximum concentrations and a specific measurement of carbon 14. Regarding radioactive releases, a new counting has been settled and activity of carbon 14 release is now measured and no longer calculated. The evolution of the French regulation leads to develop specific procedures and analytical techniques in chemistry and in radiochemistry (UV spectrometric methods, carbon 14 measurements,..) EDF NPP operators have launched a voluntarist process to reduce their releases since the beginning and before the evolution of the regulation. EDF priorities in terms of environment care lead henceforth to implement a global optimisation of the impact for a better control of releases. The new regulation will help EDF to reach its goals because it covers all the aspects in one administrative document: it is seen as a real simplification and a clarification towards public. In addition, this new regulation fits in with international practices which will allow an easier comparison of results between EDF and foreign NPP. These big environmental concerns lead EDF to create a national dedicated laboratory (LAMEN) in charge of developing specific measurement procedures to be implemented either by NPP or by sub-contractor laboratories. (authors)

  13. Hazardous animal waste carcasses transformation into slow release fertilizers.

    Science.gov (United States)

    Sharrock, Patrick; Fiallo, Marina; Nzihou, Ange; Chkir, Mouna

    2009-08-15

    Because of the need to address disposal of materials infected with pathogens new regulations have come into effect for the transport and disposal of dead farm animals or carcasses. For precautionary reasons, disposal to landfill, composting, biogas generation or fertilizer use are banned recycling paths because of incomplete knowledge about contamination transmission paths. Thermal treatment is recognized as a safe elimination process. Animal wastes have a high calorific value (above 16 MJ/kg). However, combustion of the organics leaves mineral residues (near 30%). The ashes contain mostly calcium and phosphate with some sodium, potassium and magnesium. We have examined the transformation of the ashes into a slow release fertilizer. We used a mixture of acids to partly dissolve the combustion residues and form slurry. In a second step, base was added to neutralize and solidify the reaction mixture. The final product was a whitish polycrystalline solid. Leaching tests were made to evaluate the nutrient release rate in laboratory columns. Water leachates were analyzed for up to ten pore-bed volumes and showed, as expected, large differences in release rates. Nitrate release was slowed and phosphate did not level even after ten pore-bed volumes. This demonstrates that insoluble precipitates (gypsum) contribute to control soluble ion release.

  14. RELEASE OF DRIED RADIOACTIVE WASTE MATERIALS TECHNICAL BASIS DOCUMENT

    Energy Technology Data Exchange (ETDEWEB)

    KOZLOWSKI, S.D.

    2007-05-30

    This technical basis document was developed to support RPP-23429, Preliminary Documented Safety Analysis for the Demonstration Bulk Vitrification System (PDSA) and RPP-23479, Preliminary Documented Safety Analysis for the Contact-Handled Transuranic Mixed (CH-TRUM) Waste Facility. The main document describes the risk binning process and the technical basis for assigning risk bins to the representative accidents involving the release of dried radioactive waste materials from the Demonstration Bulk Vitrification System (DBVS) and to the associated represented hazardous conditions. Appendices D through F provide the technical basis for assigning risk bins to the representative dried waste release accident and associated represented hazardous conditions for the Contact-Handled Transuranic Mixed (CH-TRUM) Waste Packaging Unit (WPU). The risk binning process uses an evaluation of the frequency and consequence of a given representative accident or represented hazardous condition to determine the need for safety structures, systems, and components (SSC) and technical safety requirement (TSR)-level controls. A representative accident or a represented hazardous condition is assigned to a risk bin based on the potential radiological and toxicological consequences to the public and the collocated worker. Note that the risk binning process is not applied to facility workers because credible hazardous conditions with the potential for significant facility worker consequences are considered for safety-significant SSCs and/or TSR-level controls regardless of their estimated frequency. The controls for protection of the facility workers are described in RPP-23429 and RPP-23479. Determination of the need for safety-class SSCs was performed in accordance with DOE-STD-3009-94, Preparation Guide for US. Department of Energy Nonreactor Nuclear Facility Documented Safety Analyses, as described below.

  15. Release of Waste Tire Comprehensive Utilization Industry Access Conditions

    Institute of Scientific and Technical Information of China (English)

    2012-01-01

    On July 31, 2012, the Ministry of Industry and Information Technology released the Tire Retread- ing lndustry Access Conditions and Waste Tire Comprehensive Utilization Industry Access Condi- tions with the No. 32 announcement of 2012. The state will lay a foundation for realizing the green, safe, efficient, eco-friendly and energy saving tar- gets in the "12th Five-year Plan" of the industry by raising access conditions, regulating industrial development order, strengthening environmental protection, promoting corporate optimizing and up- grading, improving resources comprehensive utiliza- tion technology and management level and guiding the "harmless recycling and eco-friendly utiliza- tion" of the industry.

  16. The Effect of the Addition of Active Digester Effluent for Start-up Accelerator in Anaerobic Digestion of Soybean Curd Industry Waste Water (Basic Research for Biogas Power Generation

    Directory of Open Access Journals (Sweden)

    Arini Wresta

    2012-12-01

    Full Text Available Biogas production from soybean curd industry waste water was studied in laboratory scale to improve the application of anaerobic digestion process. The problem with the soybean curd waste water was the fact that it does not sufficiently contain anaerobic microorganisms required in biogas production. Therefore, it is necessary to add a well-developed population of anaerobic microorganisms to accelerate the start-up of the anerobic digestion. This research was aimed to verify the influence of the addition of active digester effluent into the soybean curd waste water batches in an anaerobic digestion process. Batch experiments were done in two digesters. The first digester was only fed with soybean curd waste water while the second digester was fed with soybean curd waste water and active digester effluent from a digester processing cow manure which was very rich in anaerobic microorganism consortium. The results indicated that soybean curd industry waste water did not contain methanogenic bacteria but there existed some acidogenic bacteria. The addition of active digester effluent accelerated the anaerobic digestion start-up and directed the process pathway towards methanogenic process so that more methane was obtained. The high methane content obtained (more than 64% volume was very potential for power generation. The capacity of soybean curd industry must be as high as 697.13 kg soybean per day to generate the electric energy of 8.4 kWh.

  17. A Short History of Hanford Waste Generation, Storage, and Release

    Energy Technology Data Exchange (ETDEWEB)

    Gephart, Roy E.

    2003-10-01

    Nine nuclear reactors and four reprocessing plants at Hanford produced nearly two-thirds of the plutonium used in the United States for government purposes . These site operations also created large volumes of radioactive and chemical waste. Some contaminants were released into the environment, exposing people who lived downwind and downstream. Other contaminants were stored. The last reactor was shut down in 1987, and the last reprocessing plant closed in 1990. Most of the human-made radioactivity and about half of the chemicals remaining onsite are kept in underground tanks and surface facilities. The rest exists in the soil, groundwater, and burial grounds. Hanford contains about 40% of all the radioactivity that exists across the nuclear weapons complex. Today, environmental restoration activities are under way.

  18. Single-phase and two-phase anaerobic digestion of fruit and vegetable waste: comparison of start-up, reactor stability and process performance.

    Science.gov (United States)

    Ganesh, Rangaraj; Torrijos, Michel; Sousbie, Philippe; Lugardon, Aurelien; Steyer, Jean Philippe; Delgenes, Jean Philippe

    2014-05-01

    Single-phase and two-phase digestion of fruit and vegetable waste were studied to compare reactor start-up, reactor stability and performance (methane yield, volatile solids reduction and energy yield). The single-phase reactor (SPR) was a conventional reactor operated at a low loading rate (maximum of 3.5 kgVS/m3 d), while the two-phase system consisted of an acidification reactor (TPAR) and a methanogenic reactor (TPMR). The TPAR was inoculated with methanogenic sludge similar to the SPR, but was operated with step-wise increase in the loading rate and with total recirculation of reactor solids to convert it into acidification sludge. Before each feeding, part of the sludge from TPAR was centrifuged, the centrifuge liquid (solubilized products) was fed to the TPMR and centrifuged solids were recycled back to the reactor. Single-phase digestion produced a methane yield of 0.45 m3 CH4/kg VS fed and VS removal of 83%. The TPAR shifted to acidification mode at an OLR of 10.0 kgVS/m3 d and then achieved stable performance at 7.0 kgVS/m3 d and pH 5.5-6.2, with very high substrate solubilization rate and a methane yield of 0.30 m3 CH4/kg COD fed. The two-phase process was capable of high VS reduction, but material and energy balance showed that the single-phase process was superior in terms of volumetric methane production and energy yield by 33%. The lower energy yield of the two-phase system was due to the loss of energy during hydrolysis in the TPAR and the deficit in methane production in the TPMR attributed to COD loss due to biomass synthesis and adsorption of hard COD onto the flocs. These results including the complicated operational procedure of the two-phase process and the economic factors suggested that the single-phase process could be the preferred system for FVW.

  19. Models for recurrent gas release event behavior in hazardous waste tanks

    Energy Technology Data Exchange (ETDEWEB)

    Anderson, D.N. [Pacific Northwest Lab., Richland, WA (United States); Arnold, B.C. [California Univ., Riverside, CA (United States). Dept. of Statistics

    1994-08-01

    Certain radioactive waste storage tanks at the United States Department of Energy Hanford facilities continuously generate gases as a result of radiolysis and chemical reactions. The congealed sludge in these tanks traps the gases and causes the level of the waste within the tanks to rise. The waste level continues to rise until the sludge becomes buoyant and ``rolls over``, changing places with heavier fluid on top. During a rollover, the trapped gases are released, resulting, in a sudden drop in the waste level. This is known as a gas release event (GRE). After a GRE, the wastes leading to another GRE. We present nonlinear time waste re-congeals and gas again accumulates leading to another GRE. We present nonlinear time series models that produce simulated sample paths that closely resemble the temporal history of waste levels in these tanks. The models also imitate the random GRE, behavior observed in the temporal waste level history of a storage tank. We are interested in using the structure of these models to understand the probabilistic behavior of the random variable ``time between consecutive GRE`s``. Understanding the stochastic nature of this random variable is important because the hydrogen and nitrous oxide gases released from a GRE, are flammable and the ammonia that is released is a health risk. From a safety perspective, activity around such waste tanks should be halted when a GRE is imminent. With credible GRE models, we can establish time windows in which waste tank research and maintenance activities can be safely performed.

  20. Single-phase and two-phase anaerobic digestion of fruit and vegetable waste: Comparison of start-up, reactor stability and process performance

    Energy Technology Data Exchange (ETDEWEB)

    Ganesh, Rangaraj [INRA, UR50, Laboratoire de Biotechnologie de l’Environnement, Avenue des Etangs, Narbonne F-11100 (France); Torrijos, Michel, E-mail: michel.torrijos@supagro.inra.fr [INRA, UR50, Laboratoire de Biotechnologie de l’Environnement, Avenue des Etangs, Narbonne F-11100 (France); Sousbie, Philippe [INRA, UR50, Laboratoire de Biotechnologie de l’Environnement, Avenue des Etangs, Narbonne F-11100 (France); Lugardon, Aurelien [Naskeo Environnment, 52 rue Paul Vaillant Couturier, F-92240 Malakoff (France); Steyer, Jean Philippe; Delgenes, Jean Philippe [INRA, UR50, Laboratoire de Biotechnologie de l’Environnement, Avenue des Etangs, Narbonne F-11100 (France)

    2014-05-01

    Highlights: • Single-phase and two-phase systems were compared for fruit and vegetable waste digestion. • Single-phase digestion produced a methane yield of 0.45 m{sup 3} CH{sub 4}/kg VS and 83% VS removal. • Substrate solubilization was high in acidification conditions at 7.0 kg VS/m{sup 3} d and pH 5.5–6.2. • Energy yield was lower by 33% for two-phase system compared to the single-phase system. • Simple and straight-forward operation favored single phase process over two-phase process. - Abstract: Single-phase and two-phase digestion of fruit and vegetable waste were studied to compare reactor start-up, reactor stability and performance (methane yield, volatile solids reduction and energy yield). The single-phase reactor (SPR) was a conventional reactor operated at a low loading rate (maximum of 3.5 kg VS/m{sup 3} d), while the two-phase system consisted of an acidification reactor (TPAR) and a methanogenic reactor (TPMR). The TPAR was inoculated with methanogenic sludge similar to the SPR, but was operated with step-wise increase in the loading rate and with total recirculation of reactor solids to convert it into acidification sludge. Before each feeding, part of the sludge from TPAR was centrifuged, the centrifuge liquid (solubilized products) was fed to the TPMR and centrifuged solids were recycled back to the reactor. Single-phase digestion produced a methane yield of 0.45 m{sup 3} CH{sub 4}/kg VS fed and VS removal of 83%. The TPAR shifted to acidification mode at an OLR of 10.0 kg VS/m{sup 3} d and then achieved stable performance at 7.0 kg VS/m{sup 3} d and pH 5.5–6.2, with very high substrate solubilization rate and a methane yield of 0.30 m{sup 3} CH{sub 4}/kg COD fed. The two-phase process was capable of high VS reduction, but material and energy balance showed that the single-phase process was superior in terms of volumetric methane production and energy yield by 33%. The lower energy yield of the two-phase system was due to the loss of

  1. Loop Heat Pipe Startup Behaviors

    Science.gov (United States)

    Ku, Jentung

    2016-01-01

    A loop heat pipe must start successfully before it can commence its service. The startup transient represents one of the most complex phenomena in the loop heat pipe operation. This paper discusses various aspects of loop heat pipe startup behaviors. Topics include the four startup scenarios, the initial fluid distribution between the evaporator and reservoir that determines the startup scenario, factors that affect the fluid distribution between the evaporator and reservoir, difficulties encountered during the low power startup, and methods to enhance the startup success. Also addressed are the pressure spike and pressure surge during the startup transient, and repeated cycles of loop startup and shutdown under certain conditions.

  2. Release to the gas phase of metals, S and Cl during combustion of dedicated waste fractions

    DEFF Research Database (Denmark)

    Pedersen, Anne Juul; van Lith, Simone Cornelia; Frandsen, Flemming

    2010-01-01

    wood, shoes, automotive shredder waste and PVC (poly-vinyl-chloride). The waste fractions were characterized by use of wet chemical analysis, and, based on the chemical composition of the initial fuel sample and the ash residue after the experiments; the release of inorganic elements was quantified...

  3. Employer branding in startups : case startup Company CupoUnion

    OpenAIRE

    Sirotina, Natalia

    2016-01-01

    This thesis focuses on the Employer Branding in startups. The research was held within a Human Resources department of the startup company CupoUnion Ltd. The objectives of this study can be divided into theoretical and practical ones. The theoretical objective was to figure out, whether it makes sense for startups to invest money in employer branding. And, if it does, how startup companies can build their employer brand considering unique context and special circumstances of startups operatio...

  4. Employer branding in startups : case startup Company CupoUnion

    OpenAIRE

    Sirotina, Natalia

    2016-01-01

    This thesis focuses on the Employer Branding in startups. The research was held within a Human Resources department of the startup company CupoUnion Ltd. The objectives of this study can be divided into theoretical and practical ones. The theoretical objective was to figure out, whether it makes sense for startups to invest money in employer branding. And, if it does, how startup companies can build their employer brand considering unique context and special circumstances of startups operatio...

  5. Start-Up Capital

    OpenAIRE

    Verheul, Ingrid; Thurik, Roy

    2000-01-01

    textabstractFemale and male entrepreneurs differ in the way they finance their businesses. This can be attributed to the type of business and the type of management and experience (indirect effect). Female start-ups may also experience other barriers based upon discriminatory effects (direct effect). Whether gender has an impact on size and composition of start-up capital, is the subject of the present paper. To test for these direct and indirect effects data of 2000 Dutch starting entreprene...

  6. Hanford Site Tank 241-C-108 Residual Waste Contaminant Release Models and Supporting Data

    Energy Technology Data Exchange (ETDEWEB)

    Cantrell, Kirk J.; Krupka, Kenneth M.; Geiszler, Keith N.; Arey, Bruce W.; Schaef, Herbert T.

    2010-06-18

    This report presents the results of laboratory characterization, testing, and analysis for a composite sample (designated 20578) of residual waste collected from single-shell tank C-108 during the waste retrieval process after modified sluicing. These studies were completed to characterize concentration and form of contaminant of interest in the residual waste; assess the leachability of contaminants from the solids; and develop release models for contaminants of interest. Because modified sluicing did not achieve 99% removal of the waste, it is expected that additional retrieval processing will take place. As a result, the sample analyzed here is not expected to represent final retrieval sample.

  7. Electrochemical Corrosion Studies for Modeling Metallic Waste Form Release Rates

    Energy Technology Data Exchange (ETDEWEB)

    Poineau, Frederic [Univ. of Nevada, Las Vegas, NV (United States); Tamalis, Dimitri [Florida Memorial Univ., Miami Gardens, FL (United States)

    2016-08-01

    The isotope 99Tc is an important fission product generated from nuclear power production. Because of its long half-life (t1/2 = 2.13 ∙ 105 years) and beta-radiotoxicity (β⁻ = 292 keV), it is a major concern in the long-term management of spent nuclear fuel. In the spent nuclear fuel, Tc is present as an alloy with Mo, Ru, Rh, and Pd called the epsilon-phase, the relative amount of which increases with fuel burn-up. In some separation schemes for spent nuclear fuel, Tc would be separated from the spent fuel and disposed of in a durable waste form. Technetium waste forms under consideration include metallic alloys, oxide ceramics and borosilicate glass. In the development of a metallic waste form, after separation from the spent fuel, Tc would be converted to the metal, incorporated into an alloy and the resulting waste form stored in a repository. Metallic alloys under consideration include Tc–Zr alloys, Tc–stainless steel alloys and Tc–Inconel alloys (Inconel is an alloy of Ni, Cr and iron which is resistant to corrosion). To predict the long-term behavior of the metallic Tc waste form, understanding the corrosion properties of Tc metal and Tc alloys in various chemical environments is needed, but efforts to model the behavior of Tc metallic alloys are limited. One parameter that should also be considered in predicting the long-term behavior of the Tc waste form is the ingrowth of stable Ru that occurs from the radioactive decay of 99Tc (99Tc → 99Ru + β⁻). After a geological period of time, significant amounts of Ru will be present in the Tc and may affect its corrosion properties. Studying the effect of Ru on the corrosion behavior of Tc is also of importance. In this context, we studied the electrochemical behavior of Tc metal, Tc-Ni alloys (to model Tc-Inconel alloy) and Tc-Ru alloys in acidic media. The study of Tc-U alloys has also been performed in order to better understand the

  8. Conditions inside Water Pooled in a Failed Nuclear Waste Container and its Effect on Radionuclide Release

    Science.gov (United States)

    Hamdan, L. K.; Walton, J. C.; Woocay, A.

    2009-12-01

    Nuclear power use is expected to expand in the future, as part of the global clean energy initiative, to meet the world’s surging energy demand, and attenuate greenhouse gas emissions, which are mainly caused by fossil fuels. As a result, it is estimated that hundreds of thousands of metric tons of spent nuclear fuel (SNF) will accumulate. SNF disposal has major environmental (radiation exposure) and security (nuclear proliferation) concerns. Storage in unsaturated zone geological repositories is a reasonable solution for dealing with SNF. One of the key factors that determine the performance of the geological repository is the release of radionuclides from the engineered barrier system. Over time, the nuclear waste containers are expected to fail gradually due to general and localized corrosions and eventually infiltrating water will have access to the nuclear waste. Once radionuclides are released, they will be transported by water, and make their way to the accessible environment. Physical and chemical disturbances in the environment over the container will lead to different corrosion rates, causing different times and locations of penetration. One possible scenario for waste packages failure is the bathtub model, where penetrations occur on the top of the waste package and water pools inside it. In this paper the bathtub-type failed waste container is considered. We shed some light on chemical and physical processes that take place in the pooled water inside a partially failed waste container (bathtub category), and the effects of these processes on radionuclide release. Our study considers two possibilities: temperature stratification of the pooled water versus mixing process. Our calculations show that temperature stratification of the pooled water is expected when the waste package is half (or less) filled with water. On the other hand, when the waste package is fully filled (or above half) there will be mixing in the upper part of water. The effect of

  9. Effects of oral exposure to mining waste on in vivo dopamine release from rat striatum.

    OpenAIRE

    1998-01-01

    Several single components of mining waste (arsenic, manganese, lead, cadmium) to which humans are exposed at the mining area of Villa de la Paz, Mexico, are known to provoke alterations of striatal dopaminergic parameters. In this study we used an animal model to examine neurochemical changes resulting from exposure to a metal mixture. We used microdialysis to compare in vivo dopamine release from adult rats subchronically exposed to a mining waste by oral route with those from a control grou...

  10. Editorial: Startups (February 2010

    Directory of Open Access Journals (Sweden)

    Dru Lavigne

    2010-01-01

    Full Text Available Bob Sutor, Vice President of the Open Source and Linux division at IBM, recently stated that "there doesn't seem to be very many good guides about the nuts and bolts of starting an open source business". He speculates that one reason is that "there is no one way to start and run a business that involves open source". The authors in this issue of the OSBR are serial entrepreneurs, startup founders, and professionals who provide services to and interact daily with startups.

  11. Releases from the cooling water system in the Waste Tank Farm

    Energy Technology Data Exchange (ETDEWEB)

    Perkins, W.C.; Lux, C.R.

    1991-01-01

    On September 12, 1991, a cooling-water header broke in the H-Area Waste Tank farm, at the Savannah River Site, releasing contaminated water down a storm sewer that drains to the creek. A copy of the Occurrence Report is attached. As part of the follow-up on this incident, the NPSR Section was asked by Waste Management Technology to perform a probabilistic analysis of the following cases: (1) A large break in the header combined with a large break in a cooling coil inside a waste tank. (2) A large break in the header combined with a leak in a cooling coil inside a waste tank. (3) A large break in the header combined with a very small leak in a cooling coil inside a waste tank. This report documents the results of the analysis of these cases.

  12. Releases from the cooling water system in the Waste Tank Farm

    Energy Technology Data Exchange (ETDEWEB)

    Perkins, W.C.; Lux, C.R.

    1991-12-31

    On September 12, 1991, a cooling-water header broke in the H-Area Waste Tank farm, at the Savannah River Site, releasing contaminated water down a storm sewer that drains to the creek. A copy of the Occurrence Report is attached. As part of the follow-up on this incident, the NPSR Section was asked by Waste Management Technology to perform a probabilistic analysis of the following cases: (1) A large break in the header combined with a large break in a cooling coil inside a waste tank. (2) A large break in the header combined with a leak in a cooling coil inside a waste tank. (3) A large break in the header combined with a very small leak in a cooling coil inside a waste tank. This report documents the results of the analysis of these cases.

  13. Release of CFC-11 from disposal of polyurethane foam waste

    DEFF Research Database (Denmark)

    Kjeldsen, Peter; Jensen, M.H.

    2001-01-01

    The halocarbon CFC-11 has extensively been used as a blowing agent for polyurethane (PUR) insulation foams in home appliances and for residential and industrial construction. Release of CFCs is an important factor in the depletion of the ozone layer. For CFC-11 the future atmospheric concentrations...

  14. Software Startups - A Research Agenda

    Directory of Open Access Journals (Sweden)

    Michael Unterkalmsteiner

    2016-10-01

    Full Text Available Software startup companies develop innovative, software-intensive products within limited time frames and with few resources, searching for sustainable and scalable business models. Software startups are quite distinct from traditional mature software companies, but also from micro-, small-, and medium-sized enterprises, introducing new challenges relevant for software engineering research. This paper's research agenda focuses on software engineering in startups, identifying, in particular, 70+ research questions in the areas of supporting startup engineering activities, startup evolution models and patterns, ecosystems and innovation hubs, human aspects in software startups, applying startup concepts in non-startup environments, and methodologies and theories for startup research. We connect and motivate this research agenda with past studies in software startup research, while pointing out possible future directions. While all authors of this research agenda have their main background in Software Engineering or Computer Science, their interest in software startups broadens the perspective to the challenges, but also to the opportunities that emerge from multi-disciplinary research. Our audience is therefore primarily software engineering researchers, even though we aim at stimulating collaborations and research that crosses disciplinary boundaries. We believe that with this research agenda we cover a wide spectrum of the software startup industry current needs.

  15. Start-Up Capital

    NARCIS (Netherlands)

    I. Verheul (Ingrid); A.R. Thurik (Roy)

    2000-01-01

    textabstractFemale and male entrepreneurs differ in the way they finance their businesses. This can be attributed to the type of business and the type of management and experience (indirect effect). Female start-ups may also experience other barriers based upon discriminatory effects (direct

  16. Gas retention and release behavior in Hanford single-shell waste tanks

    Energy Technology Data Exchange (ETDEWEB)

    Stewart, C.W.; Brewster, M.E.; Gauglitz, P.A.; Mahoney, L.A.; Meyer, P.A.; Recknagle, K.P.; Reid, H.C.

    1996-12-01

    This report describes the current understanding of flammable gas retention and release in Hanford single-shell waste tanks based on theory, experimental results, and observations of tank behavior. The single-shell tanks likely to pose a flammable gas hazard are listed and described, and photographs of core extrusions and the waste surface are included. The credible mechanisms for significant flammable gas releases are described, and release volumes and rates are quantified as much as possible. The only mechanism demonstrably capable of producing large ({approximately}100 m{sup 3}) spontaneous gas releases is the buoyant displacement, which occurs only in tanks with a relatively deep layer of supernatant liquid. Only the double-shell tanks currently satisfy this condition. All release mechanisms believed plausible in single-shell tanks have been investigated, and none have the potential for large spontaneous gas releases. Only small spontaneous gas releases of several cubic meters are likely by these mechanisms. The reasons several other postulated gas release mechanisms are implausible or incredible are also given.

  17. Waste Form Release Data Package for the 2005 Integrated Disposal Facility Performance Assessment

    Energy Technology Data Exchange (ETDEWEB)

    Pierce, Eric M.; McGrail, B. Peter; Rodriguez, Elsa A.; Schaef, Herbert T.; Saripalli, Prasad; Serne, R. Jeffrey; Krupka, Kenneth M.; Martin, P. F.; Baum, Steven R.; Geiszler, Keith N.; Reed, Lunde R.; Shaw, Wendy J.

    2004-09-01

    This data package documents the experimentally derived input data on the representative waste glasses; LAWA44, LAWB45, and LAWC22. This data will be used for Subsurface Transport Over Reactive Multi-phases (STORM) simulations of the Integrated Disposal Facility (IDF) for immobilized low-activity waste (ILAW). The STORM code will be used to provide the near-field radionuclide release source term for a performance assessment to be issued in July 2005. Documented in this data package are data related to 1) kinetic rate law parameters for glass dissolution, 2) alkali (Na+)-hydrogen (H+) ion exchange rate, 3) chemical reaction network of secondary phases that form in accelerated weathering tests, and 4) thermodynamic equilibrium constants assigned to these secondary phases. The kinetic rate law and Na+-H+ ion exchange rate were determined from single-pass flow-through experiments. Pressurized unsaturated flow (PUF) and product consistency (PCT) tests where used for accelerated weathering or aging of the glasses in order to determine a chemical reaction network of secondary phases that form. The majority of the thermodynamic data used in this data package were extracted from the thermody-namic database package shipped with the geochemical code EQ3/6, version 8.0. Because of the expected importance of 129I release from secondary waste streams being sent to IDF from various thermal treatment processes, parameter estimates for diffusional release and solubility-controlled release from cementitious waste forms were estimated from the available literature.

  18. Effects of oral exposure to mining waste on in vivo dopamine release from rat striatum.

    Science.gov (United States)

    Rodríguez, V M; Dufour, L; Carrizales, L; Díaz-Barriga, F; Jiménez-Capdeville, M E

    1998-01-01

    Several single components of mining waste (arsenic, manganese, lead, cadmium) to which humans are exposed at the mining area of Villa de la Paz, Mexico, are known to provoke alterations of striatal dopaminergic parameters. In this study we used an animal model to examine neurochemical changes resulting from exposure to a metal mixture. We used microdialysis to compare in vivo dopamine release from adult rats subchronically exposed to a mining waste by oral route with those from a control group and from a sodium arsenite group (25 mg/kg/day). We found that arsenic and manganese do accumulate in rat brain after 2 weeks of oral exposure. The mining waste group showed significantly decreased basal levels of dihydroxyphenylacetic acid (DOPAC; 66.7 +/- 7.53 pg/ microl) when compared to a control group (113.7 +/- 14.3 pg/ microl). Although basal dopamine release rates were comparable among groups, when the system was challenged with a long-standing depolarization through high-potassium perfusion, animals exposed to mining waste were not able to sustain an increased dopamine release in response to depolarization (mining waste group 5.5 +/- 0.5 pg/ microl versus control group 21.7 +/- 5.8 pg/ microl). Also, DOPAC and homovanillic acid levels were significantly lower in exposed animals than in controls during stimulation with high potassium. The arsenite group showed a similar tendency to that from the mining waste group. In vivo microdialysis provides relevant data about the effects of a chemical mixture. Our results indicate that this mining waste may represent a health risk for the exposed population. Images Figure 1 Figure 2 Figure 3 PMID:9681976

  19. Comparison of leaching tests to determine and quantify the release of inorganic contaminants in demolition waste.

    Science.gov (United States)

    Delay, Markus; Lager, Tanja; Schulz, Horst D; Frimmel, Fritz H

    2007-01-01

    The changes in waste management policy caused by the massive generation of waste materials (e.g. construction and demolition waste material, municipal waste incineration products) has led to an increase in the reuse and recycling of waste materials. For environmental risk assessment, test procedures are necessary to examine waste materials before they can be reused. In this article, results of column and lysimeter leaching tests having been applied to inorganic compounds in a reference demolition waste material are presented. The results show a good agreement between the leaching behaviour determined with the lysimeter unit and the column units used in the laboratory. In view of less time and system requirements compared to lysimeter systems, laboratory column units can be considered as a practicable instrument to assess the time-dependent release of inorganic compounds under conditions similar to those encountered in a natural environment. The high concentrations of elements in the seepage water at the initial stage of elution are reflected by the laboratory column leaching tests. In particular, authorities or laboratories might benefit and have an easy-to-use, but nevertheless reliable, method to serve as a basis for decision-making.

  20. Analysis of Waste Leak and Toxic Chemical Release Accidents from Waste Feed Delivery (WFD) Diluent System

    Energy Technology Data Exchange (ETDEWEB)

    WILLIAMS, J.C.

    2000-09-15

    Radiological and toxicological consequences are calculated for 4 postulated accidents involving the Waste Feed Delivery (WFD) diluent addition systems. Consequences for the onsite and offsite receptor are calculated. This analysis contains technical information used to determine the accident consequences for the River Protection Project (RPP) Final Safety Analysis Report (FSAR).

  1. Nutrient release, recovery and removal from waste sludge of a biological nutrient removal system.

    Science.gov (United States)

    Wang, Yi; Zheng, Shu-Jian; Pei, Li-Ying; Ke, Li; Peng, Dang-Cong; Xia, Si-Qing

    2014-01-01

    The uncontrolled release of nutrients from waste sludge results in nitrogen and phosphorus overloading in wastewater treatment plants when supernatant is returned to the inlet. A controlled release, recovery and removal of nutrient from the waste sludge of a Biological Nutrient Removal system (BNR) are investigated. Results showed that the supernatant was of high mineral salt, high electrical conductivity and poor biodegradability, in addition to high nitrogen and phosphorus concentrations after the waste sludge was hydrolysed through sodium dodecyl sulphate addition. Subsequently, over 91.8% of phosphorus and 10.5% of nitrogen in the supernatants were extracted by the crystallization method under the conditions of 9.5 pH and 400 rpm. The precipitate was mainly struvite according to X-ray diffraction and morphological examination. A multistage anoxic-oxic Moving Bed Biofilm Reactor (MBBR) was then adopted to remove the residual carbon, nitrogen and phosphorus in the supernatant. The MBBR exhibited good performance in simultaneously removing carbon, nitrogen and phosphorus under a short aeration time, which accounted for 31.25% of a cycle. Fluorescence in situ hybridization analysis demonstrated that nitrifiers presented mainly in floc, although higher extracellular polymeric substance content, especially DNA, appeared in the biofilm. Thus, a combination of hydrolysis and precipitation, followed by the MBBR, can complete the nutrient release from the waste sludge of a BNR system, recovers nutrients from the hydrolysed liquor and removes nutrients from leftovers effectively.

  2. Analysis of the contaminants released from municipal solid waste landfill site: A case study.

    Science.gov (United States)

    Samadder, S R; Prabhakar, R; Khan, D; Kishan, D; Chauhan, M S

    2017-02-15

    Release and transport of leachate from municipal solid waste landfills pose a potential hazard to both surrounding ecosystems and human populations. In the present study, soil, groundwater, and surface water samples were collected from the periphery of a municipal solid waste landfill (located at Ranital of Jabalpur, Madhya Pradesh, India) for laboratory analysis to understand the release of contaminants. The landfill does not receive any solid wastes for dumping now as the same is under a landfill closure plan. Groundwater and soil samples were collected from the bore holes of 15m deep drilled along the periphery of the landfill and the surface water samples were collected from the existing surface water courses near the landfill. The landfill had neither any bottom liner nor any leachate collection and treatment system. Thus the leachate generated from the landfills finds paths into the groundwater and surrounding surface water courses. Concentrations of various physico-chemical parameters including some toxic metals (in collected groundwater, soil, and surface water samples) and microbiological parameters (in surface water samples) were determined. The analyzed data were integrated into ArcGIS environment and the spatial distribution of the metals and other physic- chemical parameter across the landfill was extrapolated to observe the distribution. The statistical analysis and spatial variations indicated the leaching of metals from the landfill to the groundwater aquifer system. The study will help the readers and the municipal engineers to understand the release of contaminants from landfills for better management of municipal solid wastes.

  3. Dry anaerobic digestion of food waste under mesophilic conditions: Rapid start-up with high-solid inoculums%餐厨垃圾中温干法厌氧消化快速启动实验研究

    Institute of Scientific and Technical Information of China (English)

    董滨; 王凯丽; 段妮娜; 戴翎翎; 戴晓虎

    2012-01-01

    To analyze the feasibility of rapid start-up of dry anaerobic digestion of food waste with high-solid digestate as inoculums,two parallel reactors containing high-solid and traditionally low-solid digestate were used.Start-up performance of the two digestates in dry anaerobic digestion of food waste was investigated in the completely stirred tank reactors(CSTR) at(35 ± 1) ℃.It was shown that during the same 43-day start-up period,the organic loading rate(OLR) was successfully increased to 10.0 kg · m-3 · d-1(calculated based on VS) in the case of using high-solid sludge digestate as inoculums,while only 3.5 kg · m-3 · d-1 in that with traditionally low-solid sludge digestate.Compared with the traditional start-up,the rapid start-up with high-solid digestate showed no lag time and shorter recovery time.The rapid start was 2.5 times faster than the traditional start.After the recovery period,the rapid-start system showed better performance on biogas and methane production rate,methane yield and VS degradation rate than those of traditional-start system at the same OLR.%为研究餐厨垃圾在进行干法厌氧消化时,利用高含固率消化液作为接种物进行快速启动的可行性,采用两组分别含有低含固率消化液和高含固率消化液的平行反应器,研究了在(35±1)℃完全混合反应器(CSTR)中进行的餐厨垃圾干法厌氧消化的启动性能.结果表明,在同样43d的启动过程中,使用高含固率消化液作为接种物的反应器的有机负荷可成功地增加到10.0kg·m-3·d-1(以VS计),而使用低含固率消化液作为接种物的反应器的有机负荷只能达到3.5kg·m-3·d-1(以VS计).与传统启动相比,快速启动没有停滞期,且拥有较短的恢复期;快速启动的启动速度是传统启动的2.5倍.恢复期之后,在相同的有机负荷下,快速启动的沼气和甲烷产率、甲烷产量及VS降解率都较传统启动呈现出较好的性能.

  4. Contaminant Release Data Package for Residual Waste in Single-Shell Hanford Tanks

    Energy Technology Data Exchange (ETDEWEB)

    Deutsch, William J.; Cantrell, Kirk J.; Krupka, Kenneth M.

    2007-12-01

    The Hanford Federal Facility Agreement and Consent Order requires that a Resource Conservation and Recovery Act (RCRA) Facility Investigation report be submitted to the Washington State Department of Ecology. The RCRA Facility Investigation report will provide a detailed description of the state of knowledge needed for tank farm performance assessments. This data package provides detailed technical information about contaminant release from closed single-shell tanks necessary to support the RCRA Facility Investigation report. It was prepared by Pacific Northwest National Laboratory (PNNL) for CH2M HILL Hanford Group, Inc., which is tasked by the U.S. Department of Energy (DOE) with tank closure. This data package is a compilation of contaminant release rate data for residual waste in the four Hanford single-shell tanks (SSTs) that have been tested (C-103, C-106, C-202, and C-203). The report describes the geochemical properties of the primary contaminants of interest from the perspective of long-term risk to groundwater (uranium, technetium-99, iodine-129, chromium, transuranics, and nitrate), the occurrence of these contaminants in the residual waste, release mechanisms from the solid waste to water infiltrating the tanks in the future, and the laboratory tests conducted to measure release rates.

  5. Influences of use activities and waste management on environmental releases of engineered nanomaterials

    Energy Technology Data Exchange (ETDEWEB)

    Wigger, Henning, E-mail: hwigger@uni-bremen.de [Faculty of Production Engineering, Department of Technological Design and Development, University of Bremen, Badgasteiner Str. 1, 28359 Bremen (Germany); Hackmann, Stephan [UFT Center for Environmental Research and Sustainable Technology, Department of General and Theoretical Ecology, University of Bremen, Leobener Str., 28359 Bremen (Germany); Zimmermann, Till [Faculty of Production Engineering, Department of Technological Design and Development, University of Bremen, Badgasteiner Str. 1, 28359 Bremen (Germany); ARTEC — Research Center for Sustainability Studies, Enrique-Schmidt-Str. 7, 28359 Bremen (Germany); Köser, Jan [UFT Center for Environmental Research and Sustainable Technology, Department of Sustainable Chemistry, University of Bremen, Leobener Str., 28359 Bremen (Germany); Thöming, Jorg [UFT Center for Environmental Research and Sustainable Technology, Department of Sustainable Chemical Engineering, University of Bremen, Leobener Str., 28359 Bremen (Germany); Gleich, Arnim von [Faculty of Production Engineering, Department of Technological Design and Development, University of Bremen, Badgasteiner Str. 1, 28359 Bremen (Germany); ARTEC — Research Center for Sustainability Studies, Enrique-Schmidt-Str. 7, 28359 Bremen (Germany)

    2015-12-01

    Engineered nanomaterials (ENM) offer enhanced or new functionalities and properties that are used in various products. This also entails potential environmental risks in terms of hazard and exposure. However, hazard and exposure assessment for ENM still suffer from insufficient knowledge particularly for product-related releases and environmental fate and behavior. This study therefore analyzes the multiple impacts of the product use, the properties of the matrix material, and the related waste management system (WMS) on the predicted environmental concentration (PEC) by applying nine prospective life cycle release scenarios based on reasonable assumptions. The products studied here are clothing textiles treated with silver nanoparticles (AgNPs), since they constitute a controversial application. Surprisingly, the results show counter-intuitive increases by a factor of 2.6 in PEC values for the air compartment in minimal AgNP release scenarios. Also, air releases can shift from washing to wearing activity; their associated release points may shift accordingly, potentially altering release hot spots. Additionally, at end-of-life, the fraction of AgNP-residues contained on exported textiles can be increased by 350% when assuming short product lifespans and globalized WMS. It becomes evident that certain combinations of use activities, matrix material characteristics, and WMS can influence the regional PEC by several orders of magnitude. Thus, in the light of the findings and expected ENM market potential, future assessments should consider these aspects to derive precautionary design alternatives and to enable prospective global and regional risk assessments. - Highlights: • Textile use activities and two waste management systems (WMSs) are investigated. • Matrix material and use activities determine the ENM release. • Counter-intuitive shifts of releases to air can happen during usage. • WMS export can increase by 350% in case of short service life and

  6. Persistent toxic substances released from uncontrolled e-waste recycling and actions for the future

    Energy Technology Data Exchange (ETDEWEB)

    Man, Ming [Croucher Institute for Environmental Sciences, Hong Kong Baptist University (Hong Kong); Naidu, Ravi [Cooperative Research Centre for Contamination Assessment and Remediation of Environments (CRC CARE), University of South Australia (Australia); Wong, Ming H., E-mail: mhwong@hkbu.edu.hk [Croucher Institute for Environmental Sciences, Hong Kong Baptist University (Hong Kong)

    2013-10-01

    The Basel Convention on the Control of Transboundary Movement of Hazardous Wastes and their Disposal was adopted on March 22, 1989 and enforced on May 5, 1992. Since then, the USA, one of the world's largest e-waste producers, has not ratified this Convention or the Basel Ban Amendment. Communities are still debating the legal loophole, which permits the export of whole products to other countries provided it is not for recycling. In January 2011, China's WEEE Directive was implemented, providing stricter control over e-waste imports to China, including Hong Kong, while emphasizing that e-waste recycling is the producers' responsibility. China is expected to supersede the USA as the principal e-waste producer, by 2020, according to the UNEP. Uncontrolled e-waste recycling activities generate and release heavy metals and POPs into the environment, which may be re-distributed, bioaccumulated and biomagnified, with potentially adverse human health effects. Greater efforts and scientific approaches are needed for future e-product designs of minimal toxic metal and compound use, reaping greater benefits than debating the definition and handling responsibilities of e-waste recycling. - Highlights: ► We recommended to ban uses of deca-BDE in addition to penta- and octa-BDEs. ► We suggested to replace PVC in electronic products with non-chlorinated polymers. ► Spend less time on debating responsibilities and definition of e-waste and recycling. ► Proposed to work more on eliminating sources and potentials of toxic substances.

  7. Hanford Tank 241-C-106: Residual Waste Contaminant Release Model and Supporting Data

    Energy Technology Data Exchange (ETDEWEB)

    Deutsch, William J.; Krupka, Kenneth M.; Lindberg, Michael J.; Cantrell, Kirk J.; Brown, Christopher F.; Schaef, Herbert T.

    2005-06-03

    CH2M HILL is producing risk/performance assessments to support the closure of single-shell tanks at the DOE's Hanford Site. As part of this effort, staff at PNNL were asked to develop release models for contaminants of concern that are present in residual sludge remaining in tank 241-C-106 (C-106) after final retrieval of waste from the tank. This report provides the information developed by PNNL.

  8. Hanford Tank 241-C-106: Impact of Cement Reactions on Release of Contaminants from Residual Waste

    Energy Technology Data Exchange (ETDEWEB)

    Deutsch, William J.; Krupka, Kenneth M.; Lindberg, Michael J.; Cantrell, Kirk J.; Brown, Christopher F.; Schaef, Herbert T.

    2006-09-01

    The CH2M HILL Hanford Group, Inc. (CH2M HILL) is producing risk/performance assessments to support the closure of single-shell tanks at the U.S. Department of Energy's Hanford Site. As part of this effort, staff at Pacific Northwest National Laboratory were asked to develop release models for contaminants of concern that are present in residual sludge remaining in tank 241-C-106 (C-106) after final retrieval of waste from the tank. Initial work to produce release models was conducted on residual tank sludge using pure water as the leaching agent. The results were reported in an earlier report. The decision has now been made to close the tanks after waste retrieval with a cementitious grout to minimize infiltration and maintain the physical integrity of the tanks. This report describes testing of the residual waste with a leaching solution that simulates the composition of water passing through the grout and contacting the residual waste at the bottom of the tank.

  9. Analysis of a Radioactive Release in a Nuclear Waste Disposal Facility

    Energy Technology Data Exchange (ETDEWEB)

    Poppiti, James [Dept. of Energy, Washington, DC (United States); Nelson, Roger [Dept. of Energy, Carlsbad, NM (United States); MacMillan, Walter J. [Nuclear Waste Partners, Carlsbad, NM (United States); Cunningham, Scott

    2017-07-01

    The Waste Isolation Pilot Plant (WIPP) is a 655-meter deep mine near Carlsbad, New Mexico, used to dispose the nation’s defense transuranic waste. Limited airborne radioactivity was released from a container of radioactive waste in WIPP on 14 February, 2014. As designed, a mine ventilation filtration system prevented the large scale release of contamination from the underground. However, isolation dampers leaked, which allowed the release of low levels of contaminants after the event until they were sealed. None of the exposed individuals received any recordable dose. While surface contamination was limited, contamination in the ventilation system and portions of the underground was substantial. High efficiency particulate air (HEPA) filters in the operating ventilation system ensure continued containment during recovery and resumption of disposal operations. However, ventilation flow is restricted since the incident, with all exhaust air directed through the filters. Decontamination and natural fixation by the hygroscopic nature of the salt host rock has reduced the likelihood of further contamination spread. Contamination control and ventilation system operability are crucial for resumption of operations. This article provides an operational assessment and evaluation of these two key areas.

  10. Lean start-up

    DEFF Research Database (Denmark)

    Rasmussen, Erik Stavnsager; Tanev, Stoyan

    2016-01-01

    The risk of launching new products and starting new firms is known to be extremely high. The Lean Start-up approach is a way of reducing these risks and enhancing the chances for success by validating the products and services in the market with customers before launching it in full scale. The main...... point is to develop a Minimum Viable Product that can be tested by potential customers and then pivot the idea if necessary around these customer evaluations. This iterative process goes through a number of stages with the purpose of validating the customers’ problems, the suggested solution...

  11. Direct releases to the surface and associated complementary cumulative distribution functions in the 1996 performance assessments for the Waste Isolation Pilot Plant: Direct brine release

    Energy Technology Data Exchange (ETDEWEB)

    STOELZEL,D.M.; O' BRIEN,D.G.; GARNER,J.W.; HELTON,JON CRAIG; JOHNSON,J.D.; SCOTT,L.N.

    2000-05-19

    The following topics related to the treatment of direct brine releases to the surface environment in the 1996 performance assessment for the Waste Isolation Pilot Plant (WIPP) are presented (1) mathematical description of models, (2) uncertainty and sensitivity analysis results arising from subjective (i.e., epistemic) uncertainty for individual releases, (3) construction of complementary cumulative distribution functions (CCDFs) arising from stochastic (i.e., aleatory) uncertainty, and (4) uncertainty and sensitivity analysis results for CCDFs. The presented analyses indicate that direct brine releases do not constitute a serious threat to the effectiveness of the WIPP as a disposal facility for transuranic waste. Even when the effects of uncertain analysis inputs are taken into account, the CCDFs for direct brine releases fall substantially to the left of the boundary line specified in the US Environmental Protection Agency's standard for the geologic disposal of radioactive waste (4O CFR 191.40 CFR 194).

  12. Nitrate release from waste rock dumps in the Elk Valley, British Columbia, Canada.

    Science.gov (United States)

    Mahmood, Fazilatun N; Barbour, S Lee; Kennedy, C; Hendry, M Jim

    2017-12-15

    The origin, distribution and leaching of nitrate (NO3(-)) from coal waste rock dumps in the Elk Valley, British Columbia, Canada were defined using chemical and NO3(-) isotope analyses (δ(15)N- and δ(18)O-NO3(-)) of solids samples of pre- and post-blast waste rock and from thick (up to 180m) unsaturated waste rock dump profiles constructed between 1982 and 2012 as well as water samples collected from a rock drain located at the base of one dump and effluent from humidity cell (HC) and leach pad (LP) tests on waste rock. δ(15)N- and δ(18)O-NO3(-) values and NO3(-) concentrations of waste rock and rock drain waters confirmed the source of NO3(-) in the waste rock to be explosives and that limited to no denitrification occurs in the dump. The average mass of N released during blasting was estimated to be about 3-6% of the N in the explosives. NO3(-) concentrations in the fresh-blast waste rock and recently placed waste rock used for the HC and LP experiments were highly variable, ranging from below detection to 241mg/kg. The mean and median concentrations of these samples ranged from 10-30mg/kg. In this range of concentrations, the initial aqueous concentration of fresh-blasted waste rock could range from approximately 200-600mg NO3(-)-N/L. Flushing of NO3(-) from the HCs, LPs and a deep field profile was simulated using a scale dependent leaching efficiency (f) where f ranged from 5-15% for HCs, to 35-80% for the LPs, to 80-90% for the field profile. Our findings show aqueous phase NO3(-) from blasting residuals is present at highly variable initial concentrations in waste rock and the majority of this NO3(-) (>75%) should be flushed by recharging water during displacement of the first stored water volume. Copyright © 2017 Elsevier B.V. All rights reserved.

  13. FICHe Digital Health startup portfolio

    NARCIS (Netherlands)

    2016-01-01

    The FICHe (Future Internet CHallenge eHealth) project challenged European SMEs and start-ups to develop innovative applications and businesses in the eHealth market using FIWARE technology. 80 SMEs and start-ups entered the challenge and were offered mentoring, training, technical support, a real li

  14. FFTF startup: status and results

    Energy Technology Data Exchange (ETDEWEB)

    Noordhoff, B.H.; Moore, C.E.

    1980-03-01

    Startup testing on the Fast Flux Test Facility (FFTF) during the past three years has progressed beyond initial criticality toward the principal goal of power demonstration in 1980. An overview is presented of technical results to date and project plans to achieve power demonstration and complete the startup test program.

  15. Ca(2+) and OH(-) release of ceramsites containing anorthite and gehlenite prepared from waste lime mud.

    Science.gov (United States)

    Qin, Juan; Yang, Chuanmeng; Cui, Chong; Huang, Jiantao; Hussain, Ahmad; Ma, Hailong

    2016-09-01

    Lime mud is a kind of solid waste in the papermaking industry, which has been a source of serious environmental pollution. Ceramsites containing anorthite and gehlenite were prepared from lime mud and fly ash through the solid state reaction method at 1050°C. The objective of this study was to explore the efficiency of Ca(2+) and OH(-) release and assess the phosphorus and copper ion removal performance of the ceramsites via batch experiments, X-ray diffraction (XRD) and scanning electron microscopy (SEM). The results show that Ca(2+) and OH(-) were released from the ceramsites due to the dissolution of anorthite, gehlenite and available lime. It is also concluded that gehlenite had stronger capacity for Ca(2+) and OH(-) release compared with anorthite. The Ca(2+) release could be fit well by the Avrami kinetic model. Increases of porosity, dosage and temperature were associated with increases in the concentrations of Ca(2+) and OH(-) released. Under different conditions, the ceramsites could maintain aqueous solutions in alkaline conditions (pH=9.3-10.9) and the release of Ca(2+) was not affected. The removal rates of phosphorus and copper ions were as high as 96.88% and 96.81%, respectively. The final pH values of both phosphorus and copper ions solutions changed slightly. The reuse of lime mud in the form of ceramsites is an effective strategy.

  16. [Release amount of heavy metals in cement product from co-processing waste in cement kiln].

    Science.gov (United States)

    Yang, Yu-Fei; Huang, Qi-Fei; Zhang, Xia; Yang, Yu; Wang, Qi

    2009-05-15

    Clinker was produced by Simulating cement calcination test, and concrete samples were also prepared according to national standard GB/T 17671-1999. Long-term cumulative release amount of heavy metals in cement product from co-processing waste in cement kiln was researched through leaching test which refers to EA NEN 7371 and EA NEN 7375, and one-dimensional diffusion model which is on the base of Fick diffusion law. The results show that availabilities of heavy metals are lower than the total amounts in concrete. The diffusion coefficients of heavy metals are different (Cr > As > Ni > Cd). During 30 years service, the cumulative release amounts of Cr, As, Ni and Cd are 4.43 mg/kg, 0.46 mg/kg, 1.50 mg/kg and 0.02 mg/kg, respectively, and the ratios of release which is the division of cumulative release amount and availability are 27.0%, 18.0%, 3.0% and 0.2%, respectively. The most important influence factor of cumulative release amount of heavy metal is the diffusion coefficient, and it is correlative to cumulative release amount. The diffusion coefficient of Cr and As should be controlled exactly in the processing of input the cement-kiln.

  17. Investigation of bioaerosols released from swine farms using conventional and alternative waste treatment and management technologies

    Science.gov (United States)

    Ko, G.; Simmons, O. D.; Likirdopulos, C.A.; Worley-Davis, L.; Williams, M.; Sobsey, M.D.

    2008-01-01

    Microbial air pollution from concentrated animal feeding operations (CAFOs) has raised concerns about potential public health and environmental impacts. We investigated the levels of bioaerosols released from two swine farms using conventional lagoon-sprayfield technology and ten farms using alternative waste treatment and management technologies in the United States. In total, 424 microbial air samples taken at the 12 CAFOs were analyzed for several indicator and pathogenic microorganisms, including culturable bacteria and fungi, fecal coliform, Escherichia coli, Clostridium perfringens, bacteriophage, and Salmonella. At all of the investigated farms, bacterial concentrations at the downwind boundary were higher than those at the upwind boundary, suggesting that the farms are sources of microbial air contamination. In addition, fecal indicator microorganisms were found more frequently near barns and treatment technology sites than upwind or downwind of the farms. Approximately 4.5% (19/424), 1.2% (5/424), 22.2% (94/424), and 12.3% (53/424) of samples were positive for fecal coliform, E. coli, Clostridium, and total coliphage, respectively. Based on statistical comparison of airborne fecal indicator concentrations at alternative treatment technology farms compared to control farms with conventional technology, three alternative waste treatment technologies appear to perform better at reducing the airborne release of fecal indicator microorganisms during on-farm treatment and management processes. These results demonstrate that airborne microbial contaminants are released from swine farms and pose possible exposure risks to farm workers and nearby neighbors. However, the release of airborne microorganisms appears to decrease significantly through the use of certain alternative waste management and treatment technologies. ?? 2008 American Chemical Society.

  18. Waste Isolation Pilot Plant Performance Assessment: Radionuclide Release Sensitivity to Diminished Brine and Gas Flows to/from Transuranic Waste Disposal Areas

    Directory of Open Access Journals (Sweden)

    Brad A. Day

    2017-03-01

    Full Text Available Waste Isolation Pilot Plant repository releases are evaluated through the application of modified parameters to simulate accelerated creep closure, include capillary pressure effects on relative permeability, and increase brine and gas saturation in the operations and experimental (OPS/EXP areas. The modifications to the repository model result in increased pressures and decreased brine saturations in waste areas and increased pressures and brine saturations in the OPS/EXP areas. Brine flows up the borehole during a hypothetical drilling intrusion are nearly identical and brine flows up the shaft are decreased. The modified parameters essentially halt the flow of gas from the southern waste areas to the northern nonwaste areas, except as transported through the marker beds and anhydrite layers. The combination of slightly increased waste region pressures and very slightly decreased brine saturations result in a modest increase in spallings and no significant effect on direct brine releases, with total releases from the Culebra and cutting and caving releases unaffected. Overall, the effects on total high-probability mean releases from the repository are insignificant, with total low-probability mean releases minimally increased. It is concluded that the modified OPS/EXP area parameters have an insignificant effect on the prediction of total releases.

  19. Waste isolation pilot plant performance assessment: Radionuclide release sensitivity to diminished brine and gas flows to/from transuranic waste disposal areas

    Energy Technology Data Exchange (ETDEWEB)

    Day, Brad A.; Camphouse, R. C.; Zeitler, Todd R. [Sandia National Laboratories, Carlsbad (United States)

    2017-03-15

    Waste Isolation Pilot Plant repository releases are evaluated through the application of modified parameters to simulate accelerated creep closure, include capillary pressure effects on relative permeability, and increase brine and gas saturation in the operations and experimental (OPS/EXP) areas. The modifications to the repository model result in increased pressures and decreased brine saturations in waste areas and increased pressures and brine saturations in the OPS/EXP areas. Brine flows up the borehole during a hypothetical drilling intrusion are nearly identical and brine flows up the shaft are decreased. The modified parameters essentially halt the flow of gas from the southern waste areas to the northern nonwaste areas, except as transported through the marker beds and anhydrite layers. The combination of slightly increased waste region pressures and very slightly decreased brine saturations result in a modest increase in spallings and no significant effect on direct brine releases, with total releases from the Culebra and cutting and caving releases unaffected. Overall, the effects on total high-probability mean releases from the repository are insignificant, with total low-probability mean releases minimally increased. It is concluded that the modified OPS/EXP area parameters have an insignificant effect on the prediction of total releases.

  20. Screening calculations for radioactive waste releases from non-nuclear facilities

    Energy Technology Data Exchange (ETDEWEB)

    Shulan Xu; Soederman, Ann-Louis

    2009-02-15

    A series of screening calculations have been performed to assess the potential radiological consequences of discharges of radioactive substances to the environment arising from waste from non-nuclear practices. Solid waste, as well as liquids that are not poured to the sewer, are incinerated and ashes from incineration and sludge from waste water treatment plants are disposed or reused at municipal disposal facilities. Airborne discharges refer to releases from an incineration facility and liquid discharges refer both to releases from hospitals and laboratories to the sewage system, as well as leakage from waste disposal facilities. The external exposure of workers is estimated both in the waste water treatment plant and at the disposal facility. The calculations follow the philosophy of the IAEA's safety guidance starting with a simple assessment based on very conservative assumptions which may be iteratively refined using progressively more complex models, with more realistic assumptions, as necessary. In the assessments of these types of disposal, with cautious assumptions, carried out in this report we conclude that the radiological impacts on representative individuals in the public are negligible in that they are small with respect to the target dose of 10 muSv/a. A Gaussian plume model was used to estimate the doses from airborne discharges from the incinerator and left a significant safety margin in the results considering the conservative assumptions in the calculations. For the sewage plant workers the realistic approach included a reduction in working hours and the shorter exposure time resulted in maximum doses around 10 muSv/a. The calculations for the waste disposal facility show that the doses are higher or in the range of the target dose. The excess for public exposure is mainly caused by H-3 and C-14. The assumption used in the calculation is that all of the radioactive substances sent to the incineration facility and waste water treatment

  1. Summary of four release consequence analyses for hypothetical nuclear waste repositories in salt and granite

    Energy Technology Data Exchange (ETDEWEB)

    Cole, C.R.; Bond, F.W.

    1980-12-01

    Release consequence methology developed under the Assessment of Effectiveness of Geologic Isolation Systems (AEGIS) program has now been applied to four hypothetical repository sites. This paper summarizes the results of these four studies in order to demonstrate that the far-field methodology developed under the AEGIS program offers a practical approach to the post-closure safety assessment of nuclear waste repositories sited in deep continental geologic formations. The four studies are briefly described and compared according to the following general categories: physical description of the repository (size, inventory, emplacement depth); geologic and hydrologic description of the site and the conceptual hydrologic model for the site; description of release scenario; hydrologic model implementation and results; engineered barriers and leach rate modeling; transport model implementation and results; and dose model implementation and results. These studies indicate the following: numerical modeling is a practical approach to post-closure safety assessment analysis for nuclear waste repositories; near-field modeling capability needs improvement to permit assessment of the consequences of human intrusion and pumping well scenarios; engineered barrier systems can be useful in mitigating consequences for postulated release scenarios that short-circuit the geohydrologic system; geohydrologic systems separating a repository from the natural biosphere discharge sites act to mitigate the consequences of postulated breaches in containment; and engineered barriers of types other than the containment or absorptive type may be useful.

  2. Strontium and cesium release mechanisms during unsaturated flow through waste-weathered Hanford sediments

    Energy Technology Data Exchange (ETDEWEB)

    Chang, Hyun-Shik; Um, Wooyong; Rod, Kenton A.; Serne, R. Jeffrey; Thompson, Aaron; Perdrial, Nicolas; Steefel, Carl I.; Chorover, Jon

    2011-10-01

    Leaching behavior of Sr and Cs in the vadose zone of Hanford site (WA, USA) was studied with laboratory-weathered sediments mimicking realistic conditions beneath the leaking radioactive waste storage tanks. Unsaturated column leaching experiments were conducted using background Hanford pore water focused on first 200 pore volumes. The weathered sediments were prepared by 6 months reaction with a synthetic Hanford tank waste leachate containing Sr and Cs (10-5 and 10-3 molal representative of LO- and HI-sediment, respectively) as surrogates for 90Sr and 137Cs. The mineral composition of the weathered sediments showed that zeolite (chabazite-type) and feldspathoid (sodalite-type) were the major byproducts but different contents depending on the weathering conditions. Reactive transport modeling indicated that Cs leaching was controlled by ion-exchange, while Sr release was affected primarily by dissolution of the secondary minerals. The later release of K, Al, and Si from the HI-column indicated the additional dissolution of a more crystalline mineral (cancrinite-type). A two-site ion-exchange model successfully simulated the Cs release from the LO-column. However, a three-site ion-exchange model was needed for the HI-column. The study implied that the weathering conditions greatly impact the speciation of the secondary minerals and leaching behavior of sequestrated Sr and Cs.

  3. Ni and Cr addition to alloy waste forms to reduce radionuclide environmental releases

    Energy Technology Data Exchange (ETDEWEB)

    Olson, L. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

    2016-10-11

    Reference alloy waste forms (RAW) were fabricated and underwent hybrid corrosion/immersion testing to parameterize the ANL analytical oxidative-dissolution model to enable the calculation of fractional release rates and to determine the effectiveness of Ni and Cr trim additions in reducing release rates of radionuclide surrogates. Figure 1 shows the prototypical multiphase microstructure of the alloys with each phase type contributing about equally to the exposed surface area. The waste forms tested at SRNL were variations of the RAW-6 formulation that uses HT9 as the main alloy component, and are meant to enable evaluation of the impact of Ni and Cr trim additions on the release rates of actinides and Tc-99. The test solutions were deaerated alkaline and acidic brines, ranging in pH 3 to pH 10, representing potential repositories with those conditions. The testing approach consisted of 4 major steps; 1) bare surface corrosion measurements at pH values of 3, 5, 8, and 10, 2) hybrid potentiostatic hold/exposure measurements at pH 3, 3) measurement of radionuclide concentrations and relations to anodic current from potentiostatic holds, and 4) identification of corroding phases using SEM/EDS of electrodes.

  4. Mixture experiment techniques for reducing the number of components applied for modeling waste glass sodium release

    Energy Technology Data Exchange (ETDEWEB)

    Piepel, G.; Redgate, T. [Pacific Northwest National Lab., Richland, WA (United States). Statistics Group

    1997-12-01

    Statistical mixture experiment techniques were applied to a waste glass data set to investigate the effects of the glass components on Product Consistency Test (PCT) sodium release (NR) and to develop a model for PCT NR as a function of the component proportions. The mixture experiment techniques indicate that the waste glass system can be reduced from nine to four components for purposes of modeling PCT NR. Empirical mixture models containing four first-order terms and one or two second-order terms fit the data quite well, and can be used to predict the NR of any glass composition in the model domain. The mixture experiment techniques produce a better model in less time than required by another approach.

  5. Atmospheric Dispersion Modeling of the February 2014 Waste Isolation Pilot Plant Release

    Energy Technology Data Exchange (ETDEWEB)

    Nasstrom, John [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Piggott, Tom [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Simpson, Matthew [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Lobaugh, Megan [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Tai, Lydia [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Pobanz, Brenda [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Yu, Kristen [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

    2015-07-22

    This report presents the results of a simulation of the atmospheric dispersion and deposition of radioactivity released from the Waste Isolation Pilot Plant (WIPP) site in New Mexico in February 2014. These simulations were made by the National Atmospheric Release Advisory Center (NARAC) at Lawrence Livermore National Laboratory (LLNL), and supersede NARAC simulation results published in a previous WIPP report (WIPP, 2014). The results presented in this report use additional, more detailed data from WIPP on the specific radionuclides released, radioactivity release amounts and release times. Compared to the previous NARAC simulations, the new simulation results in this report are based on more detailed modeling of the winds, turbulence, and particle dry deposition. In addition, the initial plume rise from the exhaust vent was considered in the new simulations, but not in the previous NARAC simulations. The new model results show some small differences compared to previous results, but do not change the conclusions in the WIPP (2014) report. Presented are the data and assumptions used in these model simulations, as well as the model-predicted dose and deposition on and near the WIPP site. A comparison of predicted and measured radionuclide-specific air concentrations is also presented.

  6. Waste Form Release Calculations for the 2005 Integrated Disposal Facility Performance Assessment. Erratum

    Energy Technology Data Exchange (ETDEWEB)

    Smith, Gary L. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

    2016-09-06

    This report refers to or contains Kg values for glasses LAWA44, LAWB45 and LAWC22 affected by calculations errors as identified by Papathanassiu et al. (2011). The corrected Kg values are reported in an erratum included in the revised version of the original report. The revised report can be referenced as follows: Pierce E. M. et al. (2004) Waste Form Release Data Package for the 2005 Integrated Disposal Facility Performance Assessment. PNNL-14805 Rev. 0 Erratum. Pacific Northwest National Laboratory, Richland, WA, USA.

  7. Waste Form Release Data Package for the 2005 Integrated Disposal Facility Performance Assessment Erratum

    Energy Technology Data Exchange (ETDEWEB)

    Smith, Gary L. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

    2016-09-06

    This report refers to or contains Kg values for glasses LAWA44, LAWB45 and LAWC22 affected by calculations errors as identified by Papathanassiu et al. (2011). The corrected Kg values are reported in an erratum included in the revised version of the original report. The revised report can be referenced as follows: Pierce E. M. et al. (2004) Waste Form Release Data Package for the 2005 Integrated Disposal Facility Performance Assessment. PNNL-14805 Rev. 0 Erratum. Pacific Northwest National Laboratory, Richland, WA, USA.

  8. Waste Form Release Calculations for the 2005 Integrated Disposal Facility Performance Assessment Erratum

    Energy Technology Data Exchange (ETDEWEB)

    Smith, Gary L. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

    2016-09-06

    This report refers to or contains Kg values for glasses LAWA44, LAWB45 and LAWC22 affected by calculations errors as identified by Papathanassiu et al. (2011). The corrected Kg values are reported in an erratum included in the revised version of the original report. The revised report can be referenced as follows: Pierce E. M. et al. (2004) Waste Form Release Data Package for the 2005 Integrated Disposal Facility Performance Assessment. PNNL-14805 Rev. 0 Erratum. Pacific Northwest National Laboratory, Richland, WA, USA.

  9. Waste Form Release Data Package for the 2005 Integrated Disposal Facility Performance Assessment. Erratum

    Energy Technology Data Exchange (ETDEWEB)

    Smith, Gary L. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

    2016-09-06

    This report refers to or contains Kg values for glasses LAWA44, LAWB45 and LAWC22 affected by calculations errors as identified by Papathanassiu et al. (2011). The corrected Kg values are reported in an erratum included in the revised version of the original report. The revised report can be referenced as follows: Pierce E. M. et al. (2004) Waste Form Release Data Package for the 2005 Integrated Disposal Facility Performance Assessment. PNNL-14805 Rev. 0 Erratum. Pacific Northwest National Laboratory, Richland, WA, USA.

  10. Risk-informed assessment of radionuclide release from dissolution of spent nuclear fuel and high-level waste glass

    Energy Technology Data Exchange (ETDEWEB)

    Ahn, Tae M., E-mail: tae.ahn@nrc.gov

    2017-06-15

    Highlights: • Dissolution of HLW waste form was assessed with long-term risk informed approach. • The radionuclide release rate decreases with time from the initial release rate. • Fast release radionuclides can be dispersed with discrete container failure time. • Fast release radionuclides can be restricted by container opening area. • Dissolved radionuclides may be further sequestered by sorption or others means. - Abstract: This paper aims to detail the different parameters to be considered for use in an assessment of radionuclide release. The dissolution of spent nuclear fuel and high-level nuclear waste glass was considered for risk and performance insights in a generic disposal system for more than 100,000 years. The probabilistic performance assessment includes the waste form, container, geology, and hydrology. Based on the author’s previous extended work and data from the literature, this paper presents more detailed specific cases of (1) the time dependence of radionuclide release, (2) radionuclide release coupled with container failure (rate-limiting process), (3) radionuclide release through the opening area of the container and cladding, and (4) sequestration of radionuclides in the near field after container failure. These cases are better understood for risk and performance insights. The dissolved amount of waste form is not linear with time but is higher at first. The radionuclide release rate from waste form dissolution can be constrained by container failure time. The partial opening area of the container surface may decrease radionuclide release. Radionuclides sequestered by various chemical reactions in the near field of a failed container may become stable with time as the radiation level decreases with time.

  11. Influences of use activities and waste management on environmental releases of engineered nanomaterials.

    Science.gov (United States)

    Wigger, Henning; Hackmann, Stephan; Zimmermann, Till; Köser, Jan; Thöming, Jorg; von Gleich, Arnim

    2015-12-01

    Engineered nanomaterials (ENM) offer enhanced or new functionalities and properties that are used in various products. This also entails potential environmental risks in terms of hazard and exposure. However, hazard and exposure assessment for ENM still suffer from insufficient knowledge particularly for product-related releases and environmental fate and behavior. This study therefore analyzes the multiple impacts of the product use, the properties of the matrix material, and the related waste management system (WMS) on the predicted environmental concentration (PEC) by applying nine prospective life cycle release scenarios based on reasonable assumptions. The products studied here are clothing textiles treated with silver nanoparticles (AgNPs), since they constitute a controversial application. Surprisingly, the results show counter-intuitive increases by a factor of 2.6 in PEC values for the air compartment in minimal AgNP release scenarios. Also, air releases can shift from washing to wearing activity; their associated release points may shift accordingly, potentially altering release hot spots. Additionally, at end-of-life, the fraction of AgNP-residues contained on exported textiles can be increased by 350% when assuming short product lifespans and globalized WMS. It becomes evident that certain combinations of use activities, matrix material characteristics, and WMS can influence the regional PEC by several orders of magnitude. Thus, in the light of the findings and expected ENM market potential, future assessments should consider these aspects to derive precautionary design alternatives and to enable prospective global and regional risk assessments. Copyright © 2015 Elsevier B.V. All rights reserved.

  12. Comparison of Start-up and restart processes of thermophilic anaerobic filters in waste water treatment plants; Comparacion de los procesos de arranque y rearranque de filtros anerobios termofilicos en las EDARs

    Energy Technology Data Exchange (ETDEWEB)

    Perez Garcia, M.; Romero Garcia, L.I.; Sales Marquez, D. [Departamento de Ingenieria Quimica, Tecnologia de Alimentos y Tecnologias del Medio Ambiente, Facultad de Ciencias del Mar, Universidad de Cadiz (Spain)

    1996-06-01

    An important number of agro-industries introduces the problem of the seasonal wastewaters. This causes interruptions and a necessary re-start-up of the purification plants. The present work compares and contrasts the start-up and the re-start-up of upflow stationary fixed film reactor (USFF) for the treatment of distillery wastewater based upon laboratory research, under three strategies of different operation: both re-start-up after two years and one month of inactivity and start-up the process. The outputs of the re-start-up studies indicates that the reactors with a mature bio film of high biomass immobilized concentration introduce an evolution of setting in progress very similar to the of reactors start-up with low densities of microorganisms immobilized. In consequence, the support highly colonized should contain elevated quantities of inactive biomass due problems of substrate diffusion in the interior of the bio film. (Author) 9 refs.

  13. Hanford Tank 241-C-106: Residual Waste Contaminant Release Model and Supporting Data

    Energy Technology Data Exchange (ETDEWEB)

    Deutsch, William J.; Krupka, Kenneth M.; Lindberg, Michael J.; Cantrell, Kirk J.; Brown, Christopher F.; Schaef, Herbert T.

    2007-05-23

    This report was revised in May 2007 to correct values in Section 3.4.1.7, second paragraph, last sentence; 90Sr values in Tables 3.22 and 3.32; and 99Tc values Table 4.3 and in Chapter 5. In addition, the tables in Appendix F were updated to reflect corrections to the 90Sr values. The rest of the text remains unchanged from the original report issued in May 2005. CH2M HILL is producing risk/performance assessments to support the closure of single-shell tanks at the DOE's Hanford Site. As part of this effort, staff at PNNL were asked to develop release models for contam¬inants of concern that are present in residual sludge remaining in tank 241-C-106 (C-106) after final retrieval of waste from the tank. This report provides the information developed by PNNL.

  14. Limits on the thermal energy release from radioactive wastes in a mined geologic repository

    Energy Technology Data Exchange (ETDEWEB)

    Scott, J.A.

    1983-03-01

    The theraml energy release of nuclear wastes is a major factor in the design of geologic repositories. Thermal limits need to be placed on various aspets of the geologic waste disposal system to avoid or retard the degradation of repository performance because of increased temperatures. The thermal limits in current use today are summarized in this report. These limits are placed in a hierarchial structure of thermal criteria consistent with the failure mechanism they are trying to prevent. The thermal criteria hierarchy is used to evaluate the thermal performance of a sample repository design. The design consists of disassembled BWR spent fuel, aged 10 years, close packed in a carbon steel canister with 15 cm of crushed salt backfill. The medium is bedded salt. The most-restrictive temperature for this design is the spent-fuel centerline temperature limit of 300/sup 0/C. A sensitivity study on the effects of additional cooling prior to disposal on repository thermal limits and design is performed.

  15. Effective rates of heavy metal release from alkaline wastes--quantified by column outflow experiments and inverse simulations.

    Science.gov (United States)

    Wehrer, Markus; Totsche, Kai Uwe

    2008-10-23

    Column outflow experiments operated at steady state flow conditions do not allow the identification of rate limited release processes. This requires an alternative experimental methodology. In this study, the aim was to apply such a methodology in order to identify and quantify effective release rates of heavy metals from granular wastes. Column experiments were conducted with demolition waste and municipal waste incineration (MSWI) bottom ash using different flow velocities and multiple flow interruptions. The effluent was analyzed for heavy metals, DOC, electrical conductivity and pH. The breakthrough-curves were inversely modeled with a numerical code based on the advection-dispersion equation with first order mass-transfer and nonlinear interaction terms. Chromium, Copper, Nickel and Arsenic are usually released under non-equilibrium conditions. DOC might play a role as carrier for those trace metals. By inverse simulations, generally good model fits are derived. Although some parameters are correlated and some model deficiencies can be revealed, we are able to deduce physically reasonable release-mass-transfer time scales. Applying forward simulations, the parameter space with equifinal parameter sets was delineated. The results demonstrate that the presented experimental design is capable of identifying and quantifying non-equilibrium conditions. They show also that the possibility of rate limited release must not be neglected in release and transport studies involving inorganic contaminants.

  16. Metal releases from a municipal solid waste incineration air pollution control residue mixed with compost.

    Science.gov (United States)

    Van Praagh, M; Persson, K M

    2008-08-01

    The influence of 10 wt.% mature compost was tested on the heavy metal leachate emissions from a calcium-rich municipal solid waste incineration air pollution control residue (MSWI APC). Apart from elongated columns (500 and 1250 mm), an otherwise norm compliant European percolation test setup was used. More than 99% of the metals Al, As, Cd, Cr, Cu, Fe and Ni were left in the APC residue after leaching to a liquid-to-solid ratio (L/S) of 10. Apparent short-term effects of elevated leachate DOC concentrations on heavy metal releases were not detected. Zn and Pb leachate concentrations were one order of magnitude lower for L/S 5 and 10 from the pure APC residue column, which suggests a possible long-term effect of compost on the release of these elements. Prolonging the contact time between the pore water and the material resulted in elevated leachate concentrations at L/S 0.1 to L/S 1 by a factor of 2. Only Cr and Pb concentrations were at their maxima in the first leachates at L/S 0.1. Equilibrium speciation modelling with the PHREEQC code suggested portlandite (Ca(OH)2) to control Ca solubility and pH.

  17. Light duty utility arm startup plan

    Energy Technology Data Exchange (ETDEWEB)

    Barnes, G.A.

    1998-03-11

    This Startup Plan encompasses activities necessary to perform startup and operation of the LDUA in Facility Group 3 tanks and complete turnover to CPO. The activities discussed in this plan will occur prior to, and following the US Department Energy, Richland Operations Office Operational Readiness Review. This startup plan does not authorize or direct any specific field activities or authorize a change of configuration. As such, this startup plan need not be Unresolved Safety Question (USQ) screened.

  18. Sulfur plant start-up

    Energy Technology Data Exchange (ETDEWEB)

    Hudson, Hank; Grigson, Susan [Ortloff Engineers Ltd. (United States)

    2002-02-01

    The authors discuss an Ortloff sulfur plant design concept using the Claus reaction that differs from accepted 'industry practice': cold reactor bed start-up. The process is designed to eliminate catalyst sulfation, heat damage and furnace overheating in sulfur recovery units. (UK)

  19. Hanford Tanks 241-C-202 and 241-C-203 Residual Waste Contaminant Release Models and Supporting Data

    Energy Technology Data Exchange (ETDEWEB)

    Deutsch, William J.; Krupka, Kenneth M.; Lindberg, Michael J.; Cantrell, Kirk J.; Brown, Christopher F.; Mattigod, Shas V.; Schaef, Herbert T.; Arey, Bruce W.

    2007-09-13

    As directed by Congress, the U. S. Department of Energy (DOE) established the Office of River Protection in 1998 to manage DOE's largest, most complex environmental cleanup project – retrieval of radioactive waste from Hanford tanks for treatment and eventual disposal. Sixty percent by volume of the nation's high-level radioactive waste is stored at Hanford in aging deteriorating tanks. If not cleaned up, this waste is a threat to the Columbia River and the Pacific Northwest. CH2M Hill Hanford Group, Inc., is the Office of River Protection's prime contractor responsible for the storage, retrieval, and disposal of Hanford's tank waste. As part of this effort, CH2M HILL Hanford Group, Inc. contracted with Pacific Northwest National Laboratory (PNNL) to develop release models for key contaminants that are present in residual sludge remaining after closure of Hanford Tanks 241-C-203 (C-203) and 241-C-204 (C-204). The release models were developed from data generated by laboratory characterization and testing of samples from these two tanks. These release models are being developed to support the tank closure risk assessments performed by CH2M HILL Hanford Group, Inc., for DOE.

  20. Program plan for evaluation and remediation of the generation and release of flammable gases in Hanford Site waste tanks

    Energy Technology Data Exchange (ETDEWEB)

    Johnson, G.D. (comp.)

    1991-08-01

    This program plan describes the activities being conducted for the resolution of the flammable gas problem that is associated with 23 high-level waste tanks at the Hanford Site. The classification of the wastes in all of these tanks is not final and some wastes may not be high-level wastes. However, until the characterization and classification is complete, all the tanks are treated as if they contain high-level waste. Of the 23 tanks, Tank 241-SY-101 (referred to as Tank 101-SY) has exhibited significant episodic releases of flammable gases (hydrogen and nitrous oxide) for the past 10 years. The major near-term focus of this program is for the understanding and stabilization of this tank. An understanding of the mechanism for gas generation and the processes for the episodic release will be obtained through sampling of the tank contents, laboratory studies, and modeling of the tank behavior. Additional information will be obtained through new and upgraded instrumentation for the tank. A number of remediation, or stabilization, concepts will be evaluated for near-term (2 to 3 years) applications to Tank 101-SY. Detailed safety assessments are required for all activities that will occur in the tank (sampling, removal of equipment, and addition of new instruments). This program plan presents a discussion of each task, provides schedules for near-term activities, and gives a summary of the expected work for fiscal years 1991, 1992, and 1993. 16 refs., 7 figs., 8 tabs.

  1. STEADY STATE FLAMMABLE GAS RELEASE RATE CALCULATION & LOWER FLAMMABILITY LEVEL EVALUATION FOR HANFORD TANK WASTE [SEC 1 & 2

    Energy Technology Data Exchange (ETDEWEB)

    HU, T.A.

    2003-09-30

    Flammable gases such as hydrogen, ammonia, and methane are observed in the tank dome space of the Hanford Site high-level waste tanks. This report assesses the steady-state flammability level under normal and off-normal ventilation conditions in the tank dome space for 177 double-shell tanks and single-shell tanks at the Hanford Site. The steady-state flammability level was estimated from the gas concentration of the mixture in the dome space using estimated gas release rates, Le Chatelier's rule and lower flammability limits of fuels in an air mixture. A time-dependent equation of gas concentration, which is a function of the gas release and ventilation rates in the dome space, has been developed for both soluble and insoluble gases. With this dynamic model, the time required to reach the specified flammability level at a given ventilation condition can be calculated. In the evaluation, hydrogen generation rates can be calculated for a given tank waste composition and its physical condition (e.g., waste density, waste volume, temperature, etc.) using the empirical rate equation model provided in Empirical Rate Equation Model and Rate Calculations of Hydrogen Generation for Hanford Tank Waste, HNF-3851. The release rate of other insoluble gases and the mass transport properties of the soluble gas can be derived from the observed steady-state gas concentration under normal ventilation conditions. The off-normal ventilation rate is assumed to be natural barometric breathing only. A large body of data is required to do both the hydrogen generation rate calculation and the flammability level evaluation. For tank waste that does not have sample-based data, a statistical-based value from probability distribution regression was used based on data from tanks belonging to a similar waste group. This report (Revision 3) updates the input data of hydrogen generation rates calculation for 177 tanks using the waste composition information in the Best-Basis Inventory Detail

  2. The effect of moisture on the release and enrichment of heavy metals during pyrolysis of municipal solid waste.

    Science.gov (United States)

    Raclavská, Helena; Corsaro, Agnieszka; Hlavsová, Adéla; Juchelková, Dagmar; Zajonc, Ondřej

    2015-03-01

    The investigation of the effect of moisture on the release and enrichment of heavy metals during pyrolysis of municipal solid waste is essential. This is important owing to: (i) the increasing amount of metals in the solid product of pyrolysis beyond the normalised level; (ii) the effect of moisture on the overall cost of pyrolysis process; and (iii) the utilisation of pyrolysis products. Seven metals were selected for evaluation: arsenic, cadmium, chromium, mercury, nickel, lead, and vanadium. Pyrolysis experiments were conducted in a steel retort at 650 °C. The municipal solid waste samples with moisture contents of 0, 30, and 65 wt% were investigated. The relative enrichment index and release of heavy metals were evaluated individually for liquid and solid fractions. A consistent trend was observed for the majority of metals investigated. Reductions of relative enrichment index and release, i.e. an increase of volatility, were observed for arsenic, chromium, cadmium, nickel, and vanadium, with an increase of municipal solid waste moisture. Whereas divergent results were obtained for lead and mercury. The effect of moisture on the relative enrichment index and release was greater at 65 wt% moisture than at 30 wt% for lead, and more remarkable at 30 wt% than at 65 wt% for mercury.

  3. WASTES-II: Waste System Transportation and Economic Simulation--Release 24: User's guide

    Energy Technology Data Exchange (ETDEWEB)

    Ouderkirk, S.J.

    1988-12-01

    WASTES models each reactor pool and an at-reactor, out-of-pool (ex-pool) storage facility for each reactor site. Spent fuel transfers between pools can be simulated under various constraints controlled by user input. In addition to simulating each pool and ex-pool facility, WASTES can accommodate up to ten other storage facilities of four different types: federal interim storage (FIS), monitored retrievable storage (MRS), auxiliary plants, and repositories. Considerable flexibility is allowed for the user to specify system configuration and priorities for fuel receipts. In addition, the WASTES computer code simulates very detailed (assembly-specific) movements of spent fuel throughout the waste management system. Spent fuel characteristics that are tracked by WASTES for each movement are: discharge year and month, number of assemblies, weight of uranium (MTU), exposure, original enrichment, and heat generation rate (calculated from the preceding characteristics). Data for the WASTES model is based upon the DOE reactor-specific spent fuel data base, which is developed and maintained by the Energy Information Administration (EIA). In addition to the spent fuel characteristics, this data includes reactor location, type, transportation access, and historical and projected discharge data on the number of fuel assemblies. 8 refs., 3 figs., 4 tabs.

  4. Trace-metal sources and their release from mine wastes: examples from humidity cell tests of hardrock mine waste and from Warrior Basin coal

    Science.gov (United States)

    Diehl, S.F.; Smith, Kathleen S.; Desborough, G.A.; White, W.W.; Lapakko, K.A.; Goldhaber, Martin B.; Fey, David L.

    2003-01-01

    To assess the potential impact of metal and acid contamination from mine-waste piles, it is important to identify the mineralogic source of trace metals and their mode of occurrence. Microscopic analysis of mine-waste samples from both hard-rock and coalmine waste samples demonstrate a microstructural control, as well as mineralogic control, on the source and release of trace metals into local water systems. The samples discussed herein show multiple periods of sulfide mineralization with varying concentrations of trace metals. In the first case study, two proprietary hard-rock mine-waste samples exposed to a series of humidity cell tests (which simulate intense chemical weathering conditions) generated acid and released trace metals. Some trace elements of interest were: arsenic (45-120 ppm), copper (60-320 ppm), and zinc (30-2,500 ppm). Untested and humidity cell-exposed samples were studied by X-ray diffraction, scanning electron microscope with energy dispersive X-ray (SEM/EDX), and electron microprobe analysis. Studies of one sample set revealed arsenic-bearing pyrite in early iron- and magnesium-rich carbonate-filled microveins, and iron-, copper-, arsenic-, antimony-bearing sulfides in later crosscutting silica-filled microveins. Post humidity cell tests indicated that the carbonate minerals were removed by leaching in the humidity cells, exposing pyrite to oxidative conditions. However, sulfides in the silica-filled veins were more protected. Therefore, the trace metals contained in the sulfides within the silica-filled microveins may be released to the surface and (or) ground water system more slowly over a greater time period. In the second case study, trace metal-rich pyrite-bearing coals from the Warrior Basin, Alabama were analyzed. Arsenic-bearing pyrite was observed in a late-stage pyrite phase in microfaults and microveins that crosscut earlier arsenic.

  5. An enhanced tokamak startup model

    Science.gov (United States)

    Goswami, Rajiv; Artaud, Jean-François

    2017-01-01

    The startup of tokamaks has been examined in the past in varying degree of detail. This phase typically involves the burnthrough of impurities and the subsequent rampup of plasma current. A zero-dimensional (0D) model is most widely used where the time evolution of volume averaged quantities determines the detailed balance between the input and loss of particle and power. But, being a 0D setup, these studies do not take into consideration the co-evolution of plasma size and shape, and instead assume an unchanging minor and major radius. However, it is known that the plasma position and its minor radius can change appreciably as the plasma evolves in time to fill in the entire available volume. In this paper, an enhanced model for the tokamak startup is introduced, which for the first time takes into account the evolution of plasma geometry during this brief but highly dynamic period by including realistic one-dimensional (1D) effects within the broad 0D framework. In addition the effect of runaway electrons (REs) has also been incorporated. The paper demonstrates that the inclusion of plasma cross section evolution in conjunction with REs plays an important role in the formation and development of tokamak startup. The model is benchmarked against experimental results from ADITYA tokamak.

  6. Kinetics of selenium release in mine waste from the Meade Peak Phosphatic Shale, Phosphoria Formation, Wooley Valley, Idaho, USA

    Science.gov (United States)

    Stillings, Lisa M.; Amacher, Michael C.

    2010-01-01

    Phosphorite from the Meade Peak Phosphatic Shale member of the Permian Phosphoria Formation has been mined in southeastern Idaho since 1906. Dumps of waste rock from mining operations contain high concentrations of Se which readily leach into nearby streams and wetlands. While the most common mineralogical residence of Se in the phosphatic shale is elemental Se, Se(0), Se is also an integral component of sulfide phases (pyrite, sphalerite and vaesite–pyritess) in the waste rock. It may also be present as adsorbed selenate and/or selenite, and FeSe2 and organo-selenides.Se release from the waste rock has been observed in field and laboratory experiments. Release rates calculated from waste rock dump and column leachate solutions describe the net, overall Se release from all of the possible sources of Se listed above. In field studies, Se concentration in seepage water (pH 7.4–7.8) from the Wooley Valley Unit 4 dump ranges from 3600 µg/L in May to 10 µg/L by Sept. Surface water flow, Q, from the seep also declines over the summer, from 2 L/s in May to 0.03 L/s in Sept. Se flux ([Se] ⁎ Q) reaches a steady-state of reaction with a rate constant, k, = 1.35 – 6.35e−3 h− 1 (11.8–55.6 yr− 1).Laboratory experiments were performed with the waste shale in packed bed reactors; residence time varied from 0.09 to 400 h and outlet pH ∼ 7.5. Here, Se concentration increased with increasing residence time and release was modeled with a first order reaction with k = 2.19e−3 h− 1 (19.2 yr− 1).Rate constants reported here fall within an order of magnitude of reported rate constants for oxidation of Se(0) formed by bacterial precipitation. This similarity among rate constants from both field and laboratory studies combined with the direct observation of Se(0) in waste shales of the Phosphoria Formation suggests that oxidation of Se(0) may control steady-state Se concentration in water draining the Wooley Valley waste dump.

  7. Startup and stability of thermophilic anaerobic digestion of OFMSW

    KAUST Repository

    El-Fadel, Mutasem E.

    2013-01-01

    Anaerobic digestion (AD) of the organic fraction of municipal solid waste (OFMSW) is promoted as an energy source and more recently as a greenhouse gas (GHG) mitigation measure. In this context, AD systems operating at thermophilic temperatures (55-60°C)-compared to mesophilic temperatures (35-40°C)-have the unique feature of producing hygienic soil conditioners with greater process efficiency, higher energy yield, and more GHG savings. Startup of AD systems is often constrained by the lack of acclimated seeds, leading to process instability and failure. The authors focus on strategies to startup thermophilic digesters treating OFMSW in the absence of acclimated seeds and examines constraints associated with process stability and ways to overcome them. Relevant gaps in the literature and future research needs are delineated. © 2013 Taylor & Francis Group, LLC.

  8. Investigation of some factors affecting on release of radon-222 from phosphogypsum waste associated with phosphate ore processing.

    Science.gov (United States)

    Hilal, M A; El Afifi, E M; Nayl, A A

    2015-07-01

    The aim of this study is oriented to investigate the influence of some physicochemical factors such as radium distribution, grain size, moisture content and chemical constituents on releases of radon-222 from the accumulated phosphogypsum (PG) waste. The emanation fraction, activity concentration in the pore and the surface exhalation rate of radon-222 in the bulk PG waste are 34.5 ± 0.3%, 238.6 ± 7.8 kBq m(-3) and 213 ± 6.9 mBq m(-2) s(-1), respectively. These values were varied and enhanced slightly in the fine grain sizes (F1 radon from residue PG waste was controlled positively by radium (Ra-226), calcium (CaSO4) and strontium (SrO). About 67% of radon release attributed to the grain size below 0.5 mm, while 33% due to the large grain size above 0.5 mm. The emanation fraction of Rn-222 is increased with moisture content and the maximum emanation is ∼43% of moisture of 3-8%. It reduced slowly with the continuous increase in moisture till 20%. Due to PG waste in situ can be enhancing the background to the surround workers and/or public. Therefore, the environmental negative impacts due to release of Rn-222 can be minimized by legislation to restrict its civil uses, or increasing its moisture to ∼10%, or by the particle size separation of the fine fraction containing the high levels of Ra-226 followed by a suitable chemical treatment or disposal; whereas the low release amount can be diluted and used in cement industry, roads or dam construction.

  9. Predicting Mineral N Release during Decomposition of Organic Wastes in Soil by Use of the SOILN_NO Model

    Directory of Open Access Journals (Sweden)

    Trine A. Sogn

    2011-01-01

    Full Text Available In order to predict the mineral N release associated with the use of organic waste as fertilizer in agricultural plant production, the adequacy of the SOILN_NO model has been evaluated. The original thought was that the model calibrated to data from simple incubation experiments could predict the mineral N release from organic waste products used as N fertilizer on agricultural land. First, the model was calibrated to mineral N data achieved in a laboratory experiment where different organic wastes were added to soil and incubated at 15°C for 8 weeks. Secondly, the calibrated model was tested by use of NO3 − leaching data from soil columns with barley growing in 4 different soil types, added organic waste and exposed to natural climatic conditions during three growing seasons. The SOILN_NO model reproduced relatively well the NO3 − leaching from some of the soils included in the outdoor experiment, but failed to reproduce others. Use of the calibrated model often induced underestimation of the observed NO3 − leaching. To achieve a satisfactory simulation of the NO3 − leaching, recalibration of the model had to be carried out. Thus, SOILN_NO calibrated to data from simple incubation experiments in the laboratory could not directly be used as a tool to predict the N-leaching following organic waste application in more natural agronomic plant production systems. The results emphasised the need for site- and system-specific data for model calibration before using a model for predictive purposes related to fertilizer N value of organic wastes applied to agricultural land.

  10. Release of Corrosive Species above the Grate in a Waste Boiler and the Implication for Improved Electrical Efficiency

    DEFF Research Database (Denmark)

    Bøjer, Martin; Jensen, Peter Arendt; Dam-Johansen, Kim;

    2010-01-01

    A relatively low electrical efficiency of 20−25% is obtained in typical west European waste boilers. Ash species released from the grate combustion zone form boiler deposits with high concentrations of Cl, Na, K, Zn, Pb, and S that cause corrosion of superheater tubes at high temperature. The sup......A relatively low electrical efficiency of 20−25% is obtained in typical west European waste boilers. Ash species released from the grate combustion zone form boiler deposits with high concentrations of Cl, Na, K, Zn, Pb, and S that cause corrosion of superheater tubes at high temperature....... The superheater steam temperature has to be limited to around 425 °C, and thereby, the electrical efficiency remains low compared to wood or coal-fired boilers. If a separate part of the flue gas from the grate has a low content of corrosive species, it may be used to superheat steam to a higher temperature......, and thereby, the electrical efficiency of the plant can be increased. In this study, the local temperature, the gas concentrations of CO, CO2, and O2, and the release of the volatile elements Cl, S, Na, K, Pb, Zn, Cu, and Sn were measured above the grate in a waste boiler to investigate if a selected fraction...

  11. Environmental and health impacts of February 14, 2014 radiation release from the nation's only deep geologic nuclear waste repository.

    Science.gov (United States)

    Thakur, P; Lemons, B G; Ballard, S; Hardy, R

    2015-08-01

    The environmental impact of the February 14, 2014 radiation release from the nation's only deep geologic nuclear waste repository, the Waste Isolation Pilot Plant (WIPP) was assessed using monitoring data from an independent monitoring program conducted by the Carlsbad Environmental Monitoring & Research Center (CEMRC). After almost 15 years of safe and efficient operations, the WIPP had one of its waste drums rupture underground resulting in the release of moderate levels of radioactivity into the underground air. A small amount of radioactivity also escaped to the surface through the ventilation system and was detected above ground. It was the first unambiguous release from the WIPP repository. The dominant radionuclides released were americium and plutonium, in a ratio that matches the content of the breached drum. The accelerated air monitoring campaign, which began following the accident, indicates that releases were low and localized, and no radiation-related health effects among local workers or the public would be expected. The highest activity detected was 115.2 μBq/m(3) for (241)Am and 10.2 μBq/m(3) for (239+240)Pu at a sampling station located 91 m away from the underground air exhaust point and 81.4 μBq/m(3) of (241)Am and 5.8 μBq/m(3) of (239+240)Pu at a monitoring station located approximately one kilometer northwest of the WIPP facility. CEMRC's recent monitoring data show that the concentration levels of these radionuclides have returned to normal background levels and in many instances, are not even detectable, demonstrating no long-term environmental impacts of the recent radiation release event at the WIPP. This article presents an evaluation of almost one year of environmental monitoring data that informed the public that the levels of radiation that got out to the environment were very low and did not, and will not harm anyone or have any long-term environmental consequence. In terms of radiological risk at or in the vicinity of the

  12. The rapid start-up technology for oily waste water biochemical treatment system in oilfield%油田含油污水生化处理系统快速启动技术

    Institute of Scientific and Technical Information of China (English)

    庄建全; 罗江涛; 吴波; 林刚; 纪艳娟; 郭鹏

    2013-01-01

    Due to the effect of high salinity of oily wastewater and other biological inhibitors,it is difficult to improve the microbial enzyme activity and the microbial enzyme growth was inhibited.As a result,the startup time of biochemical system is long or even failure.For improving the toleration of microorganism to oilfield wastewater,the microbial enhancer in bilolgical contact oxidation was analyzed and screened.Meanwhile,the biofilm formation technology was studied in order to determinate the reasonable salinity increase speed,shorten the startup time of biochemical systems,and provide basic de-sign parameters for the field system start-up.%受油田含油污水高矿化度及其他生物抑制剂等条件的影响,微生物酶活性难以提高,抑制其生长,导致生化系统启动时间长甚至失败。因此对生物接触氧化法中微生物强化剂配方分析筛选,提高微生物对油田污水的耐受度,同时对挂膜工艺研究,确定合理的盐度增加速度,从而缩短生化系统启动时间,为现场系统启动提供基础设计参数。

  13. Volatile trace compounds released from municipal solid waste at the transfer stage: Evaluation of environmental impacts and odour pollution.

    Science.gov (United States)

    Zhao, Yan; Lu, Wenjing; Wang, Hongtao

    2015-12-30

    Odour pollution caused by municipal solid waste is a public concern. This study quantitatively evaluated the concentration, environmental impacts, and olfaction of volatile trace compounds released from a waste transfer station. Seventy-six compounds were detected, and ethanol presented the highest releasing rate and ratio of 14.76 kg/d and 12.30 g/t of waste, respectively. Life cycle assessment showed that trichlorofluoromethane and dichlorodifluoromethane accounted for more than 99% of impact potentials to global warming and approximately 70% to human toxicity (non-carcinogenic). The major contributor for both photochemical ozone formation and ecotoxicity was ethanol. A detection threshold method was also used to evaluate odour pollution. Five compounds including methane thiol, hydrogen sulphide, ethanol, dimethyl disulphide, and dimethyl sulphide, with dilution multiples above one, were considered the critical compounds. Methane thiol showed the highest contribution to odour pollution of more than 90%, as indicated by its low threshold. Comparison of the contributions of the compounds to different environmental aspects indicated that typical pollutants varied based on specific evaluation targets and therefore should be comprehensively considered. This study provides important information and scientific methodology to elucidate the impacts of odourant compounds to the environment and odour pollution.

  14. Mechanisms of gas retention and release: Experimental results for Hanford single-shell waste tanks 241-A-101, 241-S-106, and 241-U-103

    Energy Technology Data Exchange (ETDEWEB)

    Rassat, S.D.; Caley, S.M.; Bredt, P.R.; Gauglitz, P.A.; Rinehart, D.E.; Forbes, S.V.

    1998-09-01

    The 177 underground waste storage tanks at the Hanford Site contain millions of gallons of radioactive waste resulting from the purification of nuclear materials and related processes. Through various mechanisms, flammable gas mixtures of hydrogen, ammonia, methane, and nitrous oxide are generated and retained in significant quantities within the waste in many ({approximately}25) of these tanks. The potential for large releases of retained gas from these wastes creates a flammability hazard. It is a critical component of the effort to understand the flammability hazard and a primary goal of this laboratory investigation to establish an understanding of the mechanisms of gas retention and release in these wastes. The results of bubble retention experimental studies using waste samples from several waste tanks and a variety of waste types support resolution of the Flammable Gas Safety Issue. Gas bubble retention information gained in the pursuit of safe storage will, in turn, benefit future waste operations including salt-well pumping, waste transfers, and sluicing/retrieval.

  15. The Phenomenon of Business Start-Ups.

    Science.gov (United States)

    Melis, Africa

    1990-01-01

    A study of four European countries (France, United Kingdom, Italy, and Spain) was conducted to gather data on the business start-up process and its impact on the generation of jobs, small business start-up support programs, training and counseling programs, and characteristics of successful business starters. (The original aim of the study was to…

  16. Start-up analysis for marketing strategy.

    Science.gov (United States)

    Griffith, M J; Baloff, N

    1984-01-01

    The complex start-up effect on utilization of health care services is too often overlooked or underestimated by marketing planners, leading to a range of negative consequences for both the users of services and the provider organization. Start-up analysis allows accurate estimation of these utilization effects for coordinated strategic planning among marketing finance, and operations.

  17. Lean and global technology start-ups

    DEFF Research Database (Denmark)

    Tanev, Stoyan; Rasmussen, Erik Stavnsager; Zijdemans, Erik

    2015-01-01

    In this paper the authors introduce the concept of Lean Global Start-up (LGS) as a way of emphasizing the impossibility for new technology start-ups to deal separately with business development, innovation and early internationalization. For a newly established technology firm the task of being...... of their products and the insights from business supporting organizations....

  18. A SURVIVABILITY MODEL FOR SAUDI ICT STARTUPS

    Directory of Open Access Journals (Sweden)

    Sara Almakenzi

    2015-05-01

    Full Text Available Innovation and entrepreneurship are critical elements in the transition to the knowledge-based economy and future competition. Unfortunately, innovation tends to be absent in Arab states for many reasons. To promote innovation in Saudi Arabia, for instance, it is necessary to support inventors’ ideas to turn inventions into start-up companies, which are companies in their early stage. At the same time, it seems that there is a need for more academic research to study the success factors of Saudi information and communication technology (ICT start-up companies. ICT start-ups are important to the economy because they are needed for the progress of all industries. Therefore, this study will identify the factors that lead to successful ICT start-up projects. Then, it will develop a model for the best practices in the interplay among the defined factors that will increase the opportunity to initiate successful start-ups. This research involves a factor analysis study based on a quantitative method to measure the interdependences among the success factors for ICT start-ups. The identified factors are verified using a sample of Saudi start-up companies. The study will contribute to enhancing the technological content to diversify the Saudi economy in order to prepare for the post-oil era. The study result is a survivability model for Saudi-incubated ICT startups. The resulting model has two phases, as follows: (1 the incubation period, which includes the relationships among three factors leading to constant and successful updates and upgrades of the ICT startup business model; and (2 the postincubation period, which include relationships among the three factors that help to deal with the changing nature of the market and the emergence of competing products. This solution can be applied within startups with similar conditions.

  19. Physics of Tokamak Plasma Start-up

    Science.gov (United States)

    Mueller, Dennis

    2012-10-01

    This tutorial describes and reviews the state-of-art in tokamak plasma start-up and its importance to next step devices such as ITER, a Fusion Nuclear Science Facility and a Tokamak/ST demo. Tokamak plasma start-up includes breakdown of the initial gas, ramp-up of the plasma current to its final value and the control of plasma parameters during those phases. Tokamaks rely on an inductive component, typically a central solenoid, which has enabled attainment of high performance levels that has enabled the construction of the ITER device. Optimizing the inductive start-up phase continues to be an area of active research, especially in regards to achieving ITER scenarios. A new generation of superconducting tokamaks, EAST and KSTAR, experiments on DIII-D and operation with JET's ITER-like wall are contributing towards this effort. Inductive start-up relies on transformer action to generate a toroidal loop voltage and successful start-up is determined by gas breakdown, avalanche physics and plasma-wall interaction. The goal of achieving steady-sate tokamak operation has motivated interest in other methods for start-up that do not rely on the central solenoid. These include Coaxial Helicity Injection, outer poloidal field coil start-up, and point source helicity injection, which have achieved 200, 150 and 100 kA respectively of toroidal current on closed flux surfaces. Other methods including merging reconnection startup and Electron Bernstein Wave (EBW) plasma start-up are being studied on various devices. EBW start-up generates a directed electron channel due to wave particle interaction physics while the other methods mentioned rely on magnetic helicity injection and magnetic reconnection which are being modeled and understood using NIMROD code simulations.

  20. Hanford waste-form release and sediment interaction: A status report with rationale and recommendations for additional studies

    Energy Technology Data Exchange (ETDEWEB)

    Serne, R.J. (Pacific Northwest Lab., Richland, WA (USA)); Wood, M.I. (Westinghouse Hanford Co., Richland, WA (USA))

    1990-05-01

    This report documents the currently available geochemical data base for release and retardation for actual Hanford Site materials (wastes and/or sediments). The report also recommends specific laboratory tests and presents the rationale for the recommendations. The purpose of this document is threefold: to summarize currently available information, to provide a strategy for generating additional data, and to provide recommendations on specific data collection methods and tests matrices. This report outlines a data collection approach that relies on feedback from performance analyses to ascertain when adequate data have been collected. The data collection scheme emphasizes laboratory testing based on empiricism. 196 refs., 4 figs., 36 tabs.

  1. Surfactant modified coir pith, an agricultural solid waste as adsorbent for phosphate removal and fertilizer carrier to control phosphate release.

    Science.gov (United States)

    Namasivayam, C; Kumar, M V Suresh

    2005-10-01

    The surface of coir pith, an agricultural solid waste was modified using a cationic surfactant, hexadecyltrimethylammonium bromide (HDTMA) and the modified coir pith was investigated to assess the capacity for the removal of phosphate from aqueous solution. Optimum pH for maximum phosphate adsorption was found to be 4.0. Langmuir and Freundlich isotherms were used to model the adsorption equilibrium data. Kinetic studies showed that the adsorption obeyed second order kinetics. Thermodynamic parameters were evaluated and the overall adsorption process was spontaneous and endothermic. Effect of coexisting anions has also been studied. The feasibility of using spent adsorbent as fertilizer carrier to control phosphate release was also investigated.

  2. Challenges for Success in Startups

    Science.gov (United States)

    Spitzer, Richard

    2000-03-01

    The basic challenges to a startup company such as IME have stemmed from the need to balance the business world's goal of fast entry into the market place with the necessity for a solid foundation in technology. Our technology base is broad - indeed it has the makings of a new industry - and the lure of quick commercial success in a specific application could easily make IME vulnerable to the R&D might of giant international companies. The essential challenges for success play out in business/technology decision tradeoffs: (i) preserving equity and viability while keeping R&D momentum and establishing intellectual property, (ii) attracting investors while maintaining focus on long-range goals, and (iii) developing a complete team while protecting capital resources. This balancing act keeps the company agile and resilient, qualities that large corporations could emulate with profit.

  3. Hanford Tank 241-C-103 Residual Waste Contaminant Release Models and Supporting Data

    Energy Technology Data Exchange (ETDEWEB)

    Cantrell, Kirk J.; Krupka, Kenneth M.; Deutsch, William J.; Lindberg, Michael J.; Schaef, Herbert T.; Geiszler, Keith N.; Arey, Bruce W.

    2008-01-15

    This report tabulates data generated by laboratory characterization and testing of three samples collected from tank C-103. The data presented here will form the basis for a release model that will be developed for tank C-103. These release models are being developed to support the tank risk assessments performed by CH2M HILL Hanford Group, Inc. for DOE.

  4. Rates and mechanisms of radioactive release and retention inside a waste disposal canister - in Can Processes

    Energy Technology Data Exchange (ETDEWEB)

    Oversby, V.M. (ed.) [and others

    2003-10-01

    the system that will not be present under long term disposal conditions. A simulation of long-term conditions can be done using uranium dioxide that contains a short-lived isotope of uranium, but this will not include the effects of fission product and higher actinide elements on the behaviour of the spent fuel. We designed a project that had as its objective to improve the scientific understanding of the processes that control release of radioactive species from spent fuel inside a disposal canister and the chemical changes in those species that might limit release of radioactivity from the canister. If the mechanisms that control dissolution of the fuel matrix, including self-irradiation effects, can be clarified, a more realistic assessment of the long-term behaviour of spent fuel under disposal conditions can be made. By removing uncertainties concerning waste form performance, a better assessment of the individual and collective role of the engineered barriers can be made. To achieve the overall objective of the project, the following scientific and technical objectives were set. 1. Measure the actual rate of matrix dissolution of uranium dioxide under oxidising and reducing conditions. 2. Measure the effect of alpha radiolysis on the dissolution rate of uranium dioxide under oxidising and reducing conditions. 3. Measure the dissolution rate of the matrix material of spent fuel and thereby determine the additional effects of beta and gamma radiation on uranium dioxide dissolution rate under oxidising and reducing conditions. 4. Measure the ability of actively corroding iron to reduce oxidised U(VI) to U(IV) when U is present as the complex ion uranyl carbonate. 5. Measure the rate of reduction of Np(V) species in the presence of actively corroding iron. 6. Calculate the expected equilibrium and steady state concentrations of U under the conditions of the experiments used for meeting objectives 1 through 3 and compare the calculated results with those measured in

  5. Complex coacervation of collagen hydrolysate extracted from leather solid wastes and chitosan for controlled release of lavender oil.

    Science.gov (United States)

    Ocak, Buğra

    2012-06-15

    In the world, approximately 600,000 metric tonnes of chromium-containing solid wastes are generated by the leather industry each year. Environmental concerns and escalating landfill costs are becoming increasingly serious problems to the leather industry and seeking solutions to these problems is a prime concern in much research today. In this study, solid collagen-based protein hydrolysate was isolated from chromium-tanned leather wastes and its chemical properties were determined. Microcapsules of collagen hydrolysate (CH) - chitosan (C) crosslinked with glutaraldehyde (GA) containing Lavender oil (LO) were prepared by complex coacervation method. The effects of various processing parameters, including the CH to C ratio, LO content, and GA, on the oil load (%), oil content (%), encapsulation efficiency (%) and release rate of LO from microcapsules were investigated. As the ratio of C present in the CH/C mixture and crosslinking density increased, the release rate of LO from microcapsules slowed down. Optical and scanning electron microscopy images illustrated that the LO microcapsules were spherical in shape. Fourier transform infrared spectroscopy (FTIR) studies confirmed that there was no significant interaction between CH/C complex and LO.

  6. Start-up of thermophilic-dry anaerobic digestion of OFMSW using adapted modified SEBAC inoculum.

    Science.gov (United States)

    Fdéz-Güelfo, L A; Alvarez-Gallego, C; Sales Márquez, D; Romero García, L I

    2010-12-01

    The work presented here concerns the start-up and stabilization stages of a Continuous Stirred Tank Reactor (CSTR) semicontinuously fed for the treatment of the Organic Fraction of Municipal Solid Waste (OFMSW) through anaerobic digestion at thermophilic temperature range (55 degrees C) and dry conditions (30% Total Solids). The procedure reported involves two novel aspects with respect to other start-up and stabilization protocols reported in the literature. The novel aspects concern the adaptation of the inoculum to both the operating conditions (thermophilic and dry) and to the type of waste by employing a modified SEBAC (Sequential Batch Anaerobic Composting) system and, secondly, the direct start-up of the process in a thermophilic temperature regime and feeding of the system from the first day of operation. In this way a significant reduction in the start-up time and stabilization is achieved i.e. 110 days in comparison to 250 days for the processes reported by other authors for the same type of waste and digester. The system presents suitable operational conditions to stabilize the reactor at SRT of 35 days, with a maximum biogas production of 1.944 LR/L.d with a CH(4) and CO(2) percentage of 25.27% and 68.15%, respectively. 2010 Elsevier Ltd. All rights reserved.

  7. Topical report on release scenario analysis of long-term management of high-level defense waste at the Hanford Site

    Energy Technology Data Exchange (ETDEWEB)

    Wallace, R.W.; Landstrom, D.K.; Blair, S.C.; Howes, B.W.; Robkin, M.A.; Benson, G.L.; Reisenauer, A.E.; Walters, W.H.; Zimmerman, M.G.

    1980-11-01

    Potential release scenarios for the defense high-level waste (HLW) on the Hanford Site are presented. Presented in this report are the three components necessary for evaluating the various alternatives under consideration for long-term management of Hanford defense HLW: identification of scenarios and events which might directly or indirectly disrupt radionuclide containment barriers; geotransport calculations of waste migration through the site media; and consequence (dose) analyses based on groundwater and air pathways calculations. The scenarios described in this report provide the necessary parameters for radionuclide transport and consequence analysis. Scenarios are categorized as either bounding or nonbounding. Bounding scenarios consider worst case or what if situations where an actual and significant release of waste material to the environment would happen if the scenario were to occur. Bounding scenarios include both near-term and long-term scenarios. Near-term scenarios are events which occur at 100 years from 1990. Long term scenarios are potential events considered to occur at 1000 and 10,000 years from 1990. Nonbounding scenarios consider events which result in insignificant releases or no release at all to the environment. Three release mechanisms are described in this report: (1) direct exposure of waste to the biosphere by a defined sequence of events (scenario) such as human intrusion by drilling; (2) radionuclides contacting an unconfined aquifer through downward percolation of groundwater or a rising water table; and (3) cataclysmic or explosive release of radionuclides by such mechanisms as meteorite impact, fire and explosion, criticality, or seismic events. Scenarios in this report present ways in which these release mechanisms could occur at a waste management facility. The scenarios are applied to the two in-tank waste management alternatives: in-situ disposal and continued present action.

  8. EPA Actions in Response to Release of Radioactive Material from the Waste Isolation Pilot Plant (WIPP)

    Science.gov (United States)

    This document provides information about the actions EPA is taking to support and provide oversight of the WIPP release of radioactive material response effort, and provide information for the public.

  9. Poly(ester amide)s from Poly(ethylene terephthalate) Waste for Enhancing Bone Regeneration and Controlled Release.

    Science.gov (United States)

    Natarajan, Janeni; Madras, Giridhar; Chatterjee, Kaushik

    2017-08-30

    The present study elucidates the facile synthesis and exceptional properties of a family of novel poly(ester amide)s (PEAs) based on bis(2-hydroxy ethylene) terephthalamide that was obtained from the poly(ethylene terephthalate) waste. Fourier transform infrared and (1)H NMR were used to verify the presence of ester and amide in the polymer backbone. Differential scanning calorimetry data showed that the glass transition temperature decreased with as the chain length of dicarboxylic acids increased. Dynamic mechanical analysis and contact angle studies proved that the modulus values and hydrophobicity increased with as the chain lengths of dicarboxylic acids increased. In vitro hydrolytic degradation and dye release studies demonstrated that the degradation and release decreased with as the chain lengths of dicarboxylic acids increased. Modeling these data illustrated that degradation and release follow first-order degradation and zero-order release, respectively. The in vitro cytocompatibility studies confirmed the minimal toxicity characteristic of these polymers. Osteogenic studies proved that these polymers can be highly influential in diverting the cells toward osteogenic lineage. Alizarin red staining evinced the presence of twice the amount of calcium phosphate deposits by the cells on these polymers when compared to the control. The observed result was also corroborated by the increased expression of alkaline phosphatase. These findings were further validated by the markedly higher mRNA expressions for known osteogenic markers using real time polymerase chain reaction. Therefore, these polymers efficiently promoted osteogenesis. This study demonstrates that the physical properties, degradation, and release kinetics can be altered to meet the specific requirements in organ regeneration as well as facilitate simultaneous polymer resorption through control of the chain length of the monomers. The findings of this study have significant implications for

  10. Corporate leadership and start-up entrepreneurship

    OpenAIRE

    Coulson-Thomas, Colin

    2016-01-01

    This article is based on a paper prepared by Colin Coulson-Thomas for the 2016 Dubai Global Convention on Leadership for Business Excellence. It examines the role of leadership in relation to start-up enterprises.

  11. Standard test method for accelerated leach test for diffusive releases from solidified waste and a computer program to model diffusive, fractional leaching from cylindrical waste forms

    CERN Document Server

    American Society for Testing and Materials. Philadelphia

    2008-01-01

    1.1 This test method provides procedures for measuring the leach rates of elements from a solidified matrix material, determining if the releases are controlled by mass diffusion, computing values of diffusion constants based on models, and verifying projected long-term diffusive releases. This test method is applicable to any material that does not degrade or deform during the test. 1.1.1 If mass diffusion is the dominant step in the leaching mechanism, then the results of this test can be used to calculate diffusion coefficients using mathematical diffusion models. A computer program developed for that purpose is available as a companion to this test method (Note 1). 1.1.2 It should be verified that leaching is controlled by diffusion by a means other than analysis of the leach test solution data. Analysis of concentration profiles of species of interest near the surface of the solid waste form after the test is recommended for this purpose. 1.1.3 Potential effects of partitioning on the test results can...

  12. Is there a lean future for global startups?

    DEFF Research Database (Denmark)

    Tanev, Stoyan

    2017-01-01

    This article integrates insights from the latest research on the lean startup entrepreneurial method, born-global firms, and global startups. It contributes to the clarification of terminology referring to the global aspects of startups, summarizes insights from previous literature focusing on gl......-based global startup research and practice. The analysis should benefit both researchers and practitioners in technology entrepreneurship, international entrepreneurship, and global innovation management.......This article integrates insights from the latest research on the lean startup entrepreneurial method, born-global firms, and global startups. It contributes to the clarification of terminology referring to the global aspects of startups, summarizes insights from previous literature focusing...... on global startups, and further substantiates the articulation of the need for considering the lean global startup as a new type of firm. The main message is that the lessons learned from the emergence of lean startup entrepreneurship offer a basis for promoting a similar lean phase in technology...

  13. DEMONSTRATION OF LEACHXS/ORCHESTRA CAPABILITIES BY SIMULATING CONSTITUENT RELEASE FROM A CEMENTITIOUS WASTE FORM IN A REINFORCED CONCRETE VAULT

    Energy Technology Data Exchange (ETDEWEB)

    Langton, C.; Meeussen, J.; Sloot, H.

    2010-03-31

    The objective of the work described in this report is to demonstrate the capabilities of the current version of LeachXS{trademark}/ORCHESTRA for simulating chemical behavior and constituent release processes in a range of applications that are relevant to the CBP. This report illustrates the use of LeachXS{trademark}/ORCHESTRA for the following applications: (1) Comparing model and experimental results for leaching tests for a range of cementitious materials including cement mortars, grout, stabilized waste, and concrete. The leaching test data includes liquid-solid partitioning as a function of pH and release rates based on laboratory column, monolith, and field testing. (2) Modeling chemical speciation of constituents in cementitious materials, including liquid-solid partitioning and release rates. (3) Evaluating uncertainty in model predictions based on uncertainty in underlying composition, thermodynamic, and transport characteristics. (4) Generating predominance diagrams to evaluate predicted chemical changes as a result of material aging using the example of exposure to atmospheric conditions. (5) Modeling coupled geochemical speciation and diffusion in a three layer system consisting of a layer of Saltstone, a concrete barrier, and a layer of soil in contact with air. The simulations show developing concentration fronts over a time period of 1000 years. (6) Modeling sulfate attack and cracking due to ettringite formation. A detailed example for this case is provided in a separate article by the authors (Sarkar et al. 2010). Finally, based on the computed results, the sensitive input parameters for this type of modeling are identified and discussed. The chemical speciation behavior of substances is calculated for a batch system and also in combination with transport and within a three layer system. This includes release from a barrier to the surrounding soil as a function of time. As input for the simulations, the physical and chemical properties of the

  14. Synthesizing slow-release fertilizers via mechanochemical processing for potentially recycling the waste ferrous sulfate from titanium dioxide production.

    Science.gov (United States)

    Li, Xuewei; Lei, Zhiwu; Qu, Jun; Li, Zhao; Zhou, Xiaowen; Zhang, Qiwu

    2017-01-15

    The goal of this study is aimed to develop a novel process to recycle the ferrous sulfate, the by-product of titanium dioxide industry. Zinc sulfate was added in the process of milling ferrous sulfate with calcium carbonate (CaCO3). The sulfates were transformed into carbonates to serve as slow-release fertilizers by co-grinding the starting materials of FeSO4·7H2O, ZnSO4·7H2O, and CaCO3 with small amounts of water in a planetary ball mill. The prepared samples were characterized by X-ray diffraction (XRD) analysis and quantitative measurements of the soluble ratios in water and 2% citric acid solution. It was found that Fe and Zn ions as sulfates were successfully combined with CaCO3 to form the corresponding Fe and Zn carbonates respectively. After milling, the release ratios of Fe and Zn nutrients in distilled water could be controlled at 0.1% and 0.7% respectively. Meanwhile, the release ratios of them in 2% citric acid solution were almost 98% and 100%. Milling speed was the critical parameter to facilitate the transformation reaction. The proposed process, as an easy and economical route, exhibits evident advantages, namely allowing the use of widely available and low-cost CaCO3 as well as industrial wastes of heavy metal sulfates as starting samples to prepare applicable products. Copyright © 2016 Elsevier Ltd. All rights reserved.

  15. NPR Physics Startup Testing Program

    Energy Technology Data Exchange (ETDEWEB)

    Bowers, C.E.

    1962-04-25

    The New Production Reactor, as compared to existing Hanford reactors, employs new and unique design concepts. To properly evaluate these design concepts and their effects on reactor operations, nuclear safety, and reactor life, a comprehensive testing program is planned; this program, with its objectives and restrictions, is discussed in this report. It has been developed along the same line as the C and K Reactors test, programs, and is expected to require a total time of 6--8 weeks of round-the-clock testing. This estimate includes fuel loading time, but does not include time allotments for engineering acceptance tests prior to power operation nor does it include any of the time necessary for engineering and physics tests during the extensive power ascension program. The main body of this report is presented in three parts. The first section describes startup hazards and restrictions, reactor and component safety provisions prior to loading, and the itemized listing of quantities to be measured. The second includes preliminary material and plant conditions and a brief description of the individual tests. The third section (the Appendix), written in procedure language, comprises a rather detailed description of each individual test on a tentative basis; final test details and procedures, which will lie within the boundaries authorized by this document wil1 be established through joint efforts of Operational Physics and NPR Operations sub-section personnel.

  16. The LEP startup Plan, 1998

    CERN Document Server

    Collier, Paul

    1998-01-01

    The startup planning for LEP in 1998 is presented. Operation this year is planned with the 102/90o lattice. The machine will be commissioned with this optics and operation for physics at 45 GeV fo r the Zo calibration data will be attempted. The 90/90o lattice, as a 'backup' solution for the Zo running, will only be commissioned in case of dire need. As usual there have been changes to the machine during the shutdown. The most important of which is the re-arrangement of IP6 with the installation of 8 new SC-RF modules there. IP6 and IP2 are now similar. 36 CU-RF cavities have been removed from the machine. In addition the polarisation wiggler positions have been changed in IP3 and IP7 to protect the separators from synchrotron radiation produced by the wigglers. Finally the vertical aperture of the vacuum chamber in all four experiments has been reduced to 55 mm.

  17. Solvent pre-wetting as an effective start-up method for point-of-use filter

    Science.gov (United States)

    Umeda, Toru; Sugiyama, Shinichi; Nakamura, Takashi; Momota, Makoto; Sevegney, Michael; Tsuzuki, Shuichi; Numaguchi, Toru

    2012-03-01

    An effective filter start-up method has been required by device manufacturers, mainly in order to reduce waste volume of lithography process chemicals, which become more expensive as lithography technology advances. Remaining air was monitored during static-pressure-driven filter start-up. As a result, 3500 ml of the resist was needed to eliminate remaining air. For improvement, cyclohexanone pre-wetting was applied prior to the resist introduction. As a result, the resist volume needed for the solvent displacement was 1900 ml, approximately half the volume required for staticpressure- driven start-up. Other solvents were evaluated for the pre-wetting start-up method. Results, in descending order of performance were PGME (best) Hansen solubility parameter distance between each solvent and nylon 6,6 material.

  18. Short- and long-term releases of fluorocarbons from disposal of polyurethane foam waste

    DEFF Research Database (Denmark)

    Kjeldsen, Peter; Scheutz, Charlotte

    2003-01-01

    Several halocarbons having very high global warming or ozone depletion potentials have been used as a blowing agent (BA) for insulation foam in home appliances, such as refrigerators and freezers. Many appliances are shredded after the end of their useful life. Release experiments carried out in ...

  19. Recyclability of mixed office waste papers containing pressure sensitive adhesives and silicone release liners

    Science.gov (United States)

    Julie Hess; Roberta Sena-Gomes; Lisa Davie; Marguerite Sykes

    2001-01-01

    Increased use of pressure sensitive adhesives for labels and stamps has introduced another contaminant into the office paper stream: silicone- coated release liners. This study examines methods and conditions for removal of contaminants, including these liners, from a typical batch of discarded office papers. Removal of contaminants contained in the furnish were...

  20. The electric potential of particles in interstellar space released from a nuclear waste payload

    Science.gov (United States)

    Williams, A. C.

    1980-01-01

    Mechanisms for charging a grain in the interplanetary medium include: (1) capture of solar wind electrons; (2) capture of solar wind protons; (3) ejection of electrons through the photoelectric effect due to the solar radiation; (4) escape of beta particles from beta emitters in the grain; and (5) escape of alpha particles from alpha emitters in the grain. The potentials on both nonradioactive and radioactive grains are considered with relation to particle size and time, and the distance from the Sun. Numerical results are presented where the waste mix is assumed to be PW-4b.

  1. On release of radionuclides from a near-surface radioactive waste repository to the environment

    Directory of Open Access Journals (Sweden)

    Gudelis Arūnas

    2015-09-01

    Full Text Available A closed near-surface radioactive waste repository is the source of various radionuclides causing the human exposure. Recent investigations confirm an effectiveness of the engineering barriers installed in 2006 to prevent the penetration of radionuclides to the environment. The tritium activity concentration in groundwater decreased from tens of kBq/l to below hundreds of Bq/l. The monitoring and groundwater level data suggest the leaching of tritium from previously contaminated layers of unsaturated zone by rising groundwater while 210Pb may disperse as a decay product of 226Ra daughters.

  2. The geochemical release feature of Tl in Tl-rich pyrite mine wastes: a long-term leaching test.

    Science.gov (United States)

    Li, Jinwen; Chen, Nan; Rajan, Ivy; Sun, Zhehua; Wu, Huiming; Chen, Diyun; Kong, Lingjun

    2017-05-01

    Identifying and revealing the geochemical behaviour of Tl during mine waste weathering are very important to assess the potential environmental impact of Thallium (Tl) from open mine-waste piles. Herein, two methods including the modified BCR sequential extraction and the long-term humidity cell tests (HCT) were employed to understand the Tl chemical fractions and to stimulate intense chemical weathering process, respectively. The results from BCR sequential extraction showed that the Tl concentration in the studied sample was 18.78 mg/kg, containing 1.878 mg/kg oxidisable, 0.282 mg/kg acid exchangeable and 1.596 mg/kg reducible Tl. The acid exchangeable fraction contributed to a particular potential risk to the aquatic marine life in the early stages and the Fe/Mn oxidisable fraction posed a potential risk being dissolved into solution at low pH (i.e. acidic conditions). The variations of Tl concentration in leachates were classified as two period as the pH values decrease. In the first period, the Tl concentrations decreased positively with pH value with poor correlation between pH value and SO4(2-) concentration in leachates. Drastic release of Tl was observed in the early period once the material was exposed to air and water, being ascribe to the acid exchangeable fraction bound to carbonate as dissolved by acid. During the second period, three increased peaks of Tl concentration (11.02, 16.03, 43.15 μg/L) and four increased peaks of SO4(2-) concentration (315, 390, 899.61 and 2670 mg/L) were observed. A good correlation (R (2) = 0.8384) between the concentrations of Tl and SO4(2-) was observed, indicating the Tl was mainly released from the oxidation of sulphide.

  3. Focus on the legislative approach to short half life radioactive hospital waste releasing.

    Science.gov (United States)

    Petrucci, Caterina; Traino, Antonio Claudio

    2015-11-01

    We propose to summarize the advancements introduced by the new Directive 2013/59/Euratom concerning the concept of clearance, for which the radioactive medical waste represents a typical candidate. We also intend to spotlight disputable points in the regulatory scheme in force in Italy, as well to make a contribution to evaluate whether the practice of patients' urine storing, stated by it, can be regarded to be proper. With directing our interest to radionuclides used in Nuclear Medicine, we first present an overview of how the clearance concept, and that of exemption closely related to it, have been developed from the previous Directive 96/29 to the new one; then we describe the implementation of these concepts in the Italian legislation. Subsequently we estimate the exposure due both to keeping the effluent on site and to direct discharging it to the environment. In line with a well established international consensus, the Directive 2013/59 drives simple and harmonized regulation of clearance. On the contrary, some complexity and lack of consistency can be found in the framework of the national legislation affecting the radioactive medical waste handling. In addition the practice of excreta storing is disputed not to be really beneficial. The opportunity should be taken to make the whole system of these requirements simpler and more consistent and effective when it is revised to transpose the new Directive. Copyright © 2015 Associazione Italiana di Fisica Medica. Published by Elsevier Ltd. All rights reserved.

  4. Improving Ammonium and Nitrate Release from Urea Using Clinoptilolite Zeolite and Compost Produced from Agricultural Wastes

    Directory of Open Access Journals (Sweden)

    Latifah Omar

    2015-01-01

    Full Text Available Improper use of urea may cause environmental pollution through NH3 volatilization and NO3- leaching from urea. Clinoptilolite zeolite and compost could be used to control N loss from urea by controlling NH4+ and NO3- release from urea. Soil incubation and leaching experiments were conducted to determine the effects of clinoptilolite zeolite and compost on controlling NH4+ and NO3- losses from urea. Bekenu Series soil (Typic Paleudults was incubated for 30, 60, and 90 days. A soil leaching experiment was conducted for 30 days. Urea amended with clinoptilolite zeolite and compost significantly reduced NH4+ and NO3- release from urea (soil incubation study compared with urea alone, thus reducing leaching of these ions. Ammonium and NO3- leaching losses during the 30 days of the leaching experiment were highest in urea alone compared with urea with clinoptilolite zeolite and compost treatments. At 30 days of the leaching experiment, NH4+ retention in soil with urea amended with clinoptilolite zeolite and compost was better than that with urea alone. These observations were because of the high pH, CEC, and other chemical properties of clinoptilolite zeolite and compost. Urea can be amended with clinoptilolite zeolite and compost to improve NH4+ and NO3- release from urea.

  5. Improving ammonium and nitrate release from urea using clinoptilolite zeolite and compost produced from agricultural wastes.

    Science.gov (United States)

    Omar, Latifah; Ahmed, Osumanu Haruna; Ab Majid, Nik Muhamad

    2015-01-01

    Improper use of urea may cause environmental pollution through NH3 volatilization and NO3 (-) leaching from urea. Clinoptilolite zeolite and compost could be used to control N loss from urea by controlling NH4 (+) and NO3 (-) release from urea. Soil incubation and leaching experiments were conducted to determine the effects of clinoptilolite zeolite and compost on controlling NH4 (+) and NO3 (-) losses from urea. Bekenu Series soil (Typic Paleudults) was incubated for 30, 60, and 90 days. A soil leaching experiment was conducted for 30 days. Urea amended with clinoptilolite zeolite and compost significantly reduced NH4 (+) and NO3 (-) release from urea (soil incubation study) compared with urea alone, thus reducing leaching of these ions. Ammonium and NO3 (-) leaching losses during the 30 days of the leaching experiment were highest in urea alone compared with urea with clinoptilolite zeolite and compost treatments. At 30 days of the leaching experiment, NH4 (+) retention in soil with urea amended with clinoptilolite zeolite and compost was better than that with urea alone. These observations were because of the high pH, CEC, and other chemical properties of clinoptilolite zeolite and compost. Urea can be amended with clinoptilolite zeolite and compost to improve NH4 (+) and NO3 (-) release from urea.

  6. Determining the Release of Radionuclides from Tank 18F Waste Residual Solids: FY2016 Report

    Energy Technology Data Exchange (ETDEWEB)

    King, William D. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Hobbs, David T. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

    2016-08-12

    Pore water leaching studies were conducted on actual Savannah River Site (SRS) Tank 18F residual waste solids to support Liquid Waste tank closure efforts. A test methodology was developed during previous simulant testing to produce slurries of tank residual solids and grout-representative solids in grout pore water solutions (based on SRS groundwater compositions) with pH and Eh values expected during the aging of the closed waste tank. The target conditions are provided below where the initial pore water has a reducing potential and a relatively high pH (Reducing Region II). The pore water is expected to become increasingly oxidizing with time (Oxidizing Region II) and during the latter stages of aging (Oxidizing Region III) the pH is expected to decrease. For the reducing case, tests were conducted with both unwashed and washed Tank 18F residual solids. For the oxidizing cases (Oxidizing Regions II and III), all samples were washed with simulated grout pore water solutions prior to testing, since it is expected that these conditions will occur after considerable pore water solution has passed through the system. For the reducing case, separate tests were conducted with representative ground grout solids and with calcium carbonate reagent, which is the grout phase believed to be controlling the pH. Ferrous sulfide (FeS) solids were also added to the reducing samples to lower the slurry Eh value. Calcium carbonate solids were used as the grout-representative solid phase for each of the oxidizing cases. Air purge-gas with and without CO2 removed was transferred through the oxidizing test samples and nitrogen purge-gas was transferred through the reducing test samples during leach testing. The target pH values were achieved to within 0.5 pH units for all samples. Leaching studies were conducted over an Eh range of approximately 0.7 V. However, the highest and lowest Eh values achieved of ~+0.5 V and ~-0.2 V were

  7. Determining the release of radionuclides from tank waste residual solids. FY2015 report

    Energy Technology Data Exchange (ETDEWEB)

    King, William D. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Hobbs, David T. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

    2015-09-11

    Methodology development for pore water leaching studies has been continued to support Savannah River Site High Level Waste tank closure efforts. For FY2015, the primary goal of this testing was the achievement of target pH and Eh values for pore water solutions representative of local groundwater in the presence of grout or grout-representative (CaCO3 or FeS) solids as well as waste surrogate solids representative of residual solids expected to be present in a closed tank. For oxidizing conditions representative of a closed tank after aging, a focus was placed on using solid phases believed to be controlling pH and Eh at equilibrium conditions. For three pore water conditions (shown below), the target pH values were achieved to within 0.5 pH units. Tank 18 residual surrogate solids leaching studies were conducted over an Eh range of approximately 630 mV. Significantly higher Eh values were achieved for the oxidizing conditions (ORII and ORIII) than were previously observed. For the ORII condition, the target Eh value was nearly achieved (within 50 mV). However, Eh values observed for the ORIII condition were approximately 160 mV less positive than the target. Eh values observed for the RRII condition were approximately 370 mV less negative than the target. Achievement of more positive and more negative Eh values is believed to require the addition of non-representative oxidants and reductants, respectively. Plutonium and uranium concentrations measured during Tank 18 residual surrogate solids leaching studies under these conditions (shown below) followed the general trends predicted for plutonium and uranium oxide phases, assuming equilibrium with dissolved oxygen. The highest plutonium and uranium concentrations were observed for the ORIII condition and the lowest concentrations were observed for the RRII condition. Based on these results, it is recommended that these test methodologies be used to

  8. DISP: Optimizations towards Scalable MPI Startup

    Energy Technology Data Exchange (ETDEWEB)

    Fu, Huansong [Florida State University, Tallahassee; Pophale, Swaroop S [ORNL; Gorentla Venkata, Manjunath [ORNL; Yu, Weikuan [Florida State University, Tallahassee

    2016-01-01

    Despite the popularity of MPI for high performance computing, the startup of MPI programs faces a scalability challenge as both the execution time and memory consumption increase drastically at scale. We have examined this problem using the collective modules of Cheetah and Tuned in Open MPI as representative implementations. Previous improvements for collectives have focused on algorithmic advances and hardware off-load. In this paper, we examine the startup cost of the collective module within a communicator and explore various techniques to improve its efficiency and scalability. Accordingly, we have developed a new scalable startup scheme with three internal techniques, namely Delayed Initialization, Module Sharing and Prediction-based Topology Setup (DISP). Our DISP scheme greatly benefits the collective initialization of the Cheetah module. At the same time, it helps boost the performance of non-collective initialization in the Tuned module. We evaluate the performance of our implementation on Titan supercomputer at ORNL with up to 4096 processes. The results show that our delayed initialization can speed up the startup of Tuned and Cheetah by an average of 32.0% and 29.2%, respectively, our module sharing can reduce the memory consumption of Tuned and Cheetah by up to 24.1% and 83.5%, respectively, and our prediction-based topology setup can speed up the startup of Cheetah by up to 80%.

  9. Illustrative assessment of human health issues arising from the potential release of chemotoxic substances from a generic geological disposal facility for radioactive waste.

    Science.gov (United States)

    Wilson, James C; Thorne, Michael C; Towler, George; Norris, Simon

    2011-12-01

    Many countries have a programme for developing an underground geological disposal facility for radioactive waste. A case study is provided herein on the illustrative assessment of human health issues arising from the potential release of chemotoxic and radioactive substances from a generic geological disposal facility (GDF) for radioactive waste. The illustrative assessment uses a source-pathway-receptor methodology and considers a number of human exposure pathways. Estimated exposures are compared with authoritative toxicological assessment criteria. The possibility of additive and synergistic effects resulting from exposures to mixtures of chemical contaminants or a combination of radiotoxic and chemotoxic substances is considered. The case study provides an illustration of how to assess human health issues arising from chemotoxic species released from a GDF for radioactive waste and highlights potential difficulties associated with a lack of data being available with which to assess synergistic effects. It also highlights how such difficulties can be addressed.

  10. Simplified analytical model to simulate radionuclide release from radioactive waste trenches; Modelo simplificado para simulacao da liberacao de radionuclideos de repositorios de rejeitos radioativos

    Energy Technology Data Exchange (ETDEWEB)

    Sa, Bernardete Lemes Vieira de

    2001-07-01

    In order to evaluate postclosure off-site doses from low-level radioactive waste disposal facilities, a computer code was developed to simulate the radionuclide released from waste form, transport through vadose zone and transport in the saturated zone. This paper describes the methodology used to model these process. The radionuclide released from the waste is calculated using a model based on first order kinetics and the transport through porous media was determined using semi-analytical solution of the mass transport equation, considering the limiting case of unidirectional convective transport with three-dimensional dispersion in an isotropic medium. The results obtained in this work were compared with other codes, showing good agreement. (author)

  11. Radioactive impact in sediments from an estuarine system affected by industrial wastes releases.

    Science.gov (United States)

    Bolívar, Juan Pedro; García-Tenorio, Rafael; Mas, José Luis; Vaca, Federico

    2002-03-01

    A big fertilizer industrial complex and a vast extension of phosphogypsum piles (12 km2), sited in the estuary formed by the Odiel and Tinto river mouths (southwest of Spain), are producing an unambiguous radioactive impact in their surrounding aquatic environment through radionuclides from the U-series. The levels and distribution of radionuclides in sediments from this estuarine system have been determined. The analyses of radionuclide concentrations and activity ratios have provided us with an interesting information to evaluate the extension, degree and routes of the radioactive impact, as well as for the knowledge of the different pathways followed for the radioactive contamination to disturb this natural system. The obtained results indicate that the main pathway of radioactive contamination of the estuary is through the dissolution in its waters of the radionuclides released by the industrial activities and their later fixation on the particulate materials. Tidal activity also plays an important role in the transport and homogenization along the estuary of the radioactivity released from the fertilizer plants.

  12. Application of two-barrier model of radioactive agent transport in sea water for analyzing artificial radionuclide release from containers with radioactive waste dumped in Kara Sea

    Energy Technology Data Exchange (ETDEWEB)

    Grishin, Denis S.; Laykin, Andrey I.; Kuchin, Nickolay L.; Platovskikh, Yuri A. [Krylov State Research Center, Saint Petersburg, 44 Moskovskoe shosse, 196158 (Russian Federation)

    2014-07-01

    Modeling of artificial radionuclide transport in sea water is crucial for prognosis of radioecological situation in regions where dumping of radioactive waste had been made and/or accidents with nuclear submarines had taken place. Distribution of artificial radionuclides in bottom sediments can be a detector of radionuclide release from dumped or sunk objects to marine environment. Proper model can determine the dependence between radionuclide distribution in sediments and radionuclide release. Following report describes two-barrier model of radioactive agent transport in sea water. It was tested on data from 1994 - 2013 expeditions to Novaya Zemlya bays, where regular dumping of solid radioactive waste was practiced by the former USSR from the early 1960's until 1990. Two-barrier model agrees with experimental data and allows more accurate determination of time and intensity of artificial radionuclide release from dumped containers. (authors)

  13. Estimates of water and solute release from a coal waste rock dump in the Elk Valley, British Columbia, Canada.

    Science.gov (United States)

    Villeneuve, S A; Barbour, S L; Hendry, M J; Carey, S K

    2017-12-01

    Long term (1999 to 2014) flow and water quality data from a rock drain located at the base of a coal waste rock dump constructed in the Elk Valley, British Columbia was used to characterize the release of three solutes (NO3(-), Cl(-) and SO4(2-)) from the dump and obtain whole dump estimates of net percolation (NP). The concentrations of dump derived solutes in the rock drain water were diluted by snowmelt waters from the adjacent natural watershed during the spring freshet and reached a maximum concentration during the winter baseflow period. Historical peak baseflow concentrations of conservative ions (NO3(-) and Cl(-)) increased until 2006/07 after which they decreased. This decrease was attributed to completion of the flushing of the first pore volume of water stored within the dump. The baseflow SO4(2-) concentrations increased proportionally with NO3(-) and Cl(-) to 2007, but then continued to slowly increase as NO3(-) and Cl(-) concentrations decreased. This was attributed to ongoing production of SO4(2-) due to oxidation of sulfide minerals within the dump. Based on partitioning of the annual volume of water discharged from the rock drain to waste rock effluent (NP) and water entering the rock drain laterally from the natural watershed, the mean NP values were estimated to be 446±50mm/a (area normalized net percolation/year) for the dump and 172±71mm/a for the natural watershed. The difference was attributed to greater rates of recharge in the dump from summer precipitation compared to the natural watershed where rainfall interception and enhanced evapotranspiration will increase water losses. These estimates included water moving through subsurface pathways. However, given the limitations in quantifying these flows the estimated NP rates for both the natural watershed and the waste rock dump are considered to be low, and could be much higher (e.g. ~450mm/a and ~800mm/a). Copyright © 2017 Elsevier B.V. All rights reserved.

  14. Rhizosphere Environment and Labile Phosphorus Release from Organic Waste-Amended Soils.

    Science.gov (United States)

    Dao, Thanh H.

    2015-04-01

    Crop residues and biofertilizers are primary sources of nutrients for organic crop production. However, soils treated with large amounts of nutrient-enriched manure have elevated phosphorus (P) levels in regions of intensive animal agriculture. Surpluses occurred in these amended soils, resulting in large pools of exchangeable inorganic P (Pi) and enzyme-labile organic P (Po) that averaging 30.9 and 68.2 mg kg-1, respectively. Organic acids produced during crop residue decomposition can promote the complexation of counter-ions and decouple and release unbound Pi from metal and alkali metal phosphates. Animal manure and cover crop residues also contain large amounts of soluble organic matter, and likely generate similar ligands. However, a high degree of heterogeneity in P spatial distribution in such amended fields, arising from variances in substrate physical forms ranging from slurries to dried solids, composition, and diverse application methods and equipment. Distinct clusters of Pi and Po were observed, where accumulation of the latter forms was associated with high soil microbial biomass C and reduced phosphomonoesterases' activity. Accurate estimates of plant requirements and lability of soil P pools, and real-time plant and soil P sensing systems are critical considerations to optimally manage manure-derived nutrients in crop production systems. An in situ X-ray fluorescence-based approach to sensing canopy and soil XRFS-P was developed to improve the yield-soil P relationship for optimal nutrient recommendations in addition to allowing in-the-field verification of foliar P status.

  15. The Fragile Success of Team Start-ups

    OpenAIRE

    Stam, Erik; Schutjens, Veronique

    2005-01-01

    This article describes the benefits and pitfalls of starting a firm with an entrepreneurial team, drawing on a longitudinal empirical analysis of the life course of 90 team start-ups and 1196 solo start-ups in the Netherlands. In the first three years of their existence, team start-ups perform better than solo start-ups on several success indicators. However, after this start phase, entrepreneurial teams face particular problems in realizing further growth. These team-specific bottlenecks can...

  16. Tokamak Start-up under Assistance of RF Waves

    Institute of Scientific and Technical Information of China (English)

    方瑜德

    2004-01-01

    To improve the start-up behavior of tokamak discharges and realize the low loop voltage start-up is required by performance of large scale, full superconductor tokamaks. In recent years, some kinds of RF wave have been used to assist the start-up and some exciting results have been gained. This paper introduce the investigation on both in physical principle and experimental research of the start-up process, in which high frequency RF waves were used to assist it.

  17. Analytical assessment about the simultaneous quantification of releasable pharmaceutical relevant inorganic nanoparticles in tap water and domestic waste water.

    Science.gov (United States)

    Krystek, Petra; Bäuerlein, Patrick S; Kooij, Pascal J F

    2015-03-15

    For pharmaceutical applications, the use of inorganic engineered nanoparticles is of growing interest while silver (Ag) and gold (Au) are the most relevant elements. A few methods were developed recently but the validation and the application testing were quite limited. Therefore, a routinely suitable multi element method for the identification of nanoparticles of different sizes below 100 nm and elemental composition by applying asymmetric flow field flow fraction (AF4) - inductively coupled plasma mass spectrometry (ICPMS) is developed. A complete validation model of the quantification of releasable pharmaceutical relevant inorganic nanoparticles based on Ag and Au is presented for the most relevant aqueous matrices of tap water and domestic waste water. The samples are originated from locations in the Netherlands and it is of great interest to study the unwanted presence of Ag and Au as nanoparticle residues due to possible health and environmental risks. During method development, instability effects are observed for 60 nm and 70 nm Ag ENPs with different capping agents. These effects are studied more closely in relation to matrix effects. Besides the methodological aspects, the obtained analytical results and relevant performance characteristics (e.g. measuring range, limit of detection, repeatability, reproducibility, trueness, and expanded uncertainty of measurement) are determined and discussed. For the chosen aqueous matrices, the results of the performance characteristics are significantly better for Au ENPs in comparison to Ag ENPs; e.g. repeatability and reproducibility are below 10% for all Au ENPs respectively maximal 27% repeatability for larger Ag ENPs. The method is a promising tool for the simultaneous determination of releasable pharmaceutical relevant inorganic nanoparticles.

  18. Releases of radioactivity at the Savannah River Plant, 1954--1985

    Energy Technology Data Exchange (ETDEWEB)

    Zeigler, C.C.; Lawrimore, I.B.

    1988-07-01

    Radioactive releases from Savannah River Plant (SRP) facilities to air, water and earthen seepage basins have been monitored and tabulated throughout the history of the site. The purpose of this report is to provide a source of data on routine releases of radioactivity to air, water and seepage basins that can be used for analyses of trends, environmental impact, etc. As used in this report, routine radioactive releases means radioactive materials that are released through established effluents from process facilities. This report is not intended to provide interpretation of the release values, their transport and impact or information on spills, leaks, buried waste or special use facilities. These subjects are covered in other SRP publications. This report provides a summary of radioactive releases that reflects the release values contained in records and documents from startup through 1985. Releases are tabulated in the following categories: Annual radioactive releases by emission source and radionuclide for 1954 through 1985; Annual radioactive releases by receptor medium and radionuclide for 1954 through 1985; Monthly releases by emission source and radionuclide for 1981 through 1985. The presentation of all SRP routine radioactive releases data in these categories provides a reference for historic data on SRP releases. 34 refs.

  19. Tokamak startup with electron cyclotron heating

    Energy Technology Data Exchange (ETDEWEB)

    Holly, D J; Prager, S C; Shepard, D A; Sprott, J C

    1980-04-01

    Experiments are described in which the startup voltage in a tokamak is reduced by approx. 60% by the use of a modest amount of electron cyclotron resonance heating power for preionization. A 50% reduction in volt-second requirement and impurity reflux are also observed.

  20. Startup of an industrial adiabatic tubular reactor

    NARCIS (Netherlands)

    Verwijs, J.W.; Berg, van den H.; Westerterp, K.R.

    1992-01-01

    The dynamic behaviour of an adiabatic tubular plant reactor during the startup is demonstrated, together with the impact of a feed-pump failure of one of the reactants. A dynamic model of the reactor system is presented, and the system response is calculated as a function of experimentally-determine

  1. The Lean and Global Start-up

    DEFF Research Database (Denmark)

    Tanev, Stoyan; Rasmussen, Erik Stavnsager

    Ventures research and research with a focus on the Lean Start-up company. It is our intention in this paper to give a short presentation of the two research streams and show how they can be merged into one with a focus on newly established technology oriented firms that are lean and global from...

  2. Light duty utility arm startup plan

    Energy Technology Data Exchange (ETDEWEB)

    Barnes, G.A.

    1998-09-01

    This plan details the methods and procedures necessary to ensure a safe transition in the operation of the Light Duty Utility Arm (LDUA) System. The steps identified here outline the work scope and identify responsibilities to complete startup, and turnover of the LDUA to Characterization Project Operations (CPO).

  3. A Monte Carlo procedure for the construction of complementary cumulative distribution functions for comparison with the EPA release limits for radioactive waste disposal

    Energy Technology Data Exchange (ETDEWEB)

    Helton, J.C.; Shiver, A.W.

    1994-10-01

    A Monte Carlo procedure for the construction of complementary cumulative distribution functions (CCDFs) for comparison with the US Environmental Protection Agency (EPA) release limits for radioactive waste disposal (40 CFR 191, Subpart B) is described and illustrated with results from a recent performance assessment (PA) for the Waste Isolation Pilot Plant (WIPP). The Monte Carlo procedure produces CCDF estimates similar to those obtained with stratified sampling in several recent PAs for the WIPP. The advantages of the Monte Carlo procedure over stratified sampling include increased resolution in the calculation of probabilities for complex scenarios involving drilling intrusions and better use of the necessarily limited number of mechanistic calculations that underlie CCDF construction.

  4. The magnitude and relevance of the February 2014 radiation release from the Waste Isolation Pilot Plant repository in New Mexico, USA.

    Science.gov (United States)

    Thakur, P; Lemons, B G; White, C R

    2016-09-15

    After almost fifteen years of successful waste disposal operations, the first unambiguous airborne radiation release from the Waste Isolation Pilot Plant (WIPP) was detected beyond the site boundary on February 14, 2014. It was the first accident of its kind in the 15-year operating history of the WIPP. The accident released moderate levels of radioactivity into the underground air. A small but measurable amount of radioactivity also escaped to the surface through the ventilation system and was detected above ground. The dominant radionuclides released were americium and plutonium, in a ratio consistent with the known content of a breached drum. The radiation release was caused by a runaway chemical reaction inside a transuranic (TRU) waste drum which experienced a seal and lid failure, spewing radioactive materials into the repository. According to source-term estimation, approximately 2 to 10Ci of radioactivity was released from the breached drum into the underground, and an undetermined fraction of that source term became airborne, setting off an alarm and triggering the closure of seals designed to force exhausting air through a system of filters including high-efficiency-particulate-air (HEPA) filters. Air monitoring across the WIPP site intensified following the first reports of radiation detection underground to determine the extent of impact to WIPP personnel, the public, and the environment, if any. This article attempts to compile and interpret analytical data collected by an independent monitoring program conducted by the Carlsbad Environmental Monitoring & Research Center (CEMRC) and by a compliance-monitoring program conducted by the WIPP's management and operating contractor, the Nuclear Waste Partnership (NWP), LLC., in response to the accident. Both the independent and the WIPP monitoring efforts concluded that the levels detected were very low and localized, and no radiation-related health effects among local workers or the public would be expected.

  5. Use of leaching tests to quantify trace element release from waste to energy bottom ash amended pavements.

    Science.gov (United States)

    Roessler, Justin G; Townsend, Timothy G; Ferraro, Christopher C

    2015-12-30

    A series of roadway tests strips were paved on-site at a landfill in Florida, U.S. Waste to energy (WTE) bottom ash was used as a partial course aggregate replacement in a hot mix asphalt (HMA) and a Portland cement concrete (PCC) pavement, along with control HMA and PCC sections. This allowed for a comparison of the relative degree of leaching between both materials (HMA and PCC) as well as between the ash-amended and control pavements. Batch and monolithic tank leaching tests were conducted on the pavements. Testing of the PCC samples demonstrated that Mo and Al were elevated above regulatory thresholds for both the control and ash amended samples. Further leach testing demonstrated that the release of Mo was likely from the PCC and not a result of the inclusion of the BA into pavement. Batch leach testing of ash-amended HMA samples revealed Sb as a constituent of potential concern. The results of the monolith leaching test displayed leaching of Sb within the same order of magnitude as the regulatory threshold. Calculation of the leachability index (LI) for Sb found that it would have limited mobility when incorporated in the HMA matrix. Copyright © 2015 Elsevier B.V. All rights reserved.

  6. Start-up date announced

    CERN Multimedia

    7th August 2008. CERN has announced that the first attempt to circulate the beam in the LHC will be made on the 10th September. This news comes as the cool down phase of commissioning the accelerator reaches a successful conclusion.The next phase is the synchronization of the LHC with the SPS accelerator, the last link in the LHC’s injector chain. A first synchronization test is scheduled for the 9th August, for the clockwise circulating beam, with the second to follow over the coming weeks.Once stable circulating beams have been established in September they will be brought to collision, and the final step will be to commission the LHC’s acceleration system to boost the energy to 5 TeV, the target energy for 2008.“We’re finishing a marathon with a sprint”, said LHC project leader Lyn Evans. “It’s been a long haul, and we’re all eager to get the LHC research programme underway.”For more information, please see the recent press release at: http://press.web.cern.ch/press/PressReleases/Rele...

  7. Radioactive Waste.

    Science.gov (United States)

    Blaylock, B. G.

    1978-01-01

    Presents a literature review of radioactive waste disposal, covering publications of 1976-77. Some of the studies included are: (1) high-level and long-lived wastes, and (2) release and burial of low-level wastes. A list of 42 references is also presented. (HM)

  8. Lean Startup: A success factor? A quantitative study of how use of the Lean Startup framework affects the success of Norwegian high-tech startups.

    OpenAIRE

    2015-01-01

    Lean Startup is a framework for entrepreneurship that has gained considerable popularity among entrepreneurs, yet the framework has not been thoroughly scrutinized in academic circles. This thesis aims to fill this gap in two ways. First, by comparing Lean Startup to more established models on entrepreneurship in a theoretical perspective. Second, by conducting an empirical study of how Lean Startup influences entrepreneurial success in practice. In our theoretical review, we found that while...

  9. Monitoring of gross alpha, gross beta and actinides activities in exhaust air released from the waste isolation pilot plant

    Energy Technology Data Exchange (ETDEWEB)

    Thakur, P., E-mail: pthakur@cemrc.org [Carlsbad Environmental Monitoring and Research Center, 1400 University Drive, Carlsbad, New Mexico 88220 (United States); Mulholland, G.P. [Carlsbad Environmental Monitoring and Research Center, 1400 University Drive, Carlsbad, New Mexico 88220 (United States)

    2011-09-15

    The simultaneous measurements of gross alpha and beta activities is one of the simplest radioanalytical technique used as a method for screening samples of both high and low activities of alpha and beta emitting radionuclides in environmental and bioassay samples. Such measurements are of great interest from both a radiological, waste disposal viewpoint, and to establish a trend of radioactivity based on long term monitoring. At the WIPP (Waste Isolation Pilot Plant) site, unfiltered exhaust air from the underground repository is the most important effluent. As part of its monitoring program, the particulates from WIPP exhaust air are collected everyday at a location typically called the Fixed Air Sampler (FAS) site or Station A, this site is located at the release point for aerosol effluents from the underground to the environment. The measurements of gross alpha and beta activity on air filter samples were performed using an ultra low level counter, PIC-MPC 9604-{alpha}/{beta}, from Protean Instrument Corporation. The high sensitivity of the gross alpha and beta instrument enables detection of low value activity from the air filters. In 2009, the values of gross alpha and beta activity concentrations ranged from Simultaneous measurements of gross alpha and gross beta activities in the particulates from WIPP exhaust air were performed. > Ultra low level counter, PIC-MPC 9604-{alpha}/{beta} counter was used for the measurements. > Values of gross alpha activity concentrations ranged from Values of gross beta activity concentrations ranged from

  10. Plasma system for start-up of pulverized fuel-fired boilers

    Energy Technology Data Exchange (ETDEWEB)

    Dyjakon, A.K. [Wroclaw Univ. of Technology, Wroclaw (Poland). Inst. of Power Engineering and Fluid Mechanics

    2009-07-01

    Pulverized coal combustion requires preliminary heating of the combustion chamber. Conventional heavy oil start-up systems are used during the boiler kindling, resulting in pollution, additional maintenance and high cost. This paper described the advantages of a plasma start-up system for the ignition and stabilization of a pulverized coal flame in coal-fired steam boiler. In a plasma start-up system, the heat source for ignition and stabilization of the pulverized coal combustion is a plasma at a temperature of 5,000 to 10,000 degrees C. The plasma interaction involves rapid heating of coal particles and thermal decomposition of the organic compounds resulting in fast release of the volatile matter and destruction of particles below 5 {mu}m. It also involves thermal dissociation of gaseous products with radical generation and gas ionization. The highly reactive mixture that is produced promotes flame propagation in the presence of oxygen. A continuous plasma discharge in a pulverized burner stabilizes the dust flame. This paper described the advantages associated with the use of a plasma start-up system, such as the possibility of limiting pollutant emissions to the atmosphere. It also presented laboratory study results on the influence of the fuels such as lignite, bituminous coal, wood and carbonaceous shale and their properties on the operational range of the plasma assisted pulverized coal burner. 13 refs., 2 tabs., 7 figs.

  11. Geochemical characterisation of pyrite oxidation and environmental problems related to release and transport of metals from a coal washing low-grade waste dump, Shahrood, northeast Iran.

    Science.gov (United States)

    Doulati Ardejani, Faramarz; Jodieri Shokri, Behshad; Moradzadeh, Ali; Shafaei, Seyed Ziadin; Kakaei, Reza

    2011-12-01

    Pyrite oxidation and release of the oxidation products from a low-grade coal waste dump to stream, groundwater and soil was investigated by geochemical and hydrogeochemical techniques at Alborz Sharghi coal washing plant, Shahrood, northeast Iran. Hydrogeochemical analysis of water samples indicates that the metal concentrations in the stream waters were low. Moreover, the pH of the water showed no considerable change. The analysis of the stream water samples shows that except the physical changes, pyrite oxidation process within the coal washing waste dump has not affected the quality of the stream water. Water type was determined to be calcium sulphate. The results of the analysis of groundwater samples indicate that the pH varies from 7.41 to 7.51. The concentrations of the toxic metals were low. The concentration of SO4 is slightly above than its standard concentration in potable water. It seems that the groundwater less affected by the coal washing operation in the study area. Geochemical analysis of the sediment samples shows that Fe concentration decreases gradually downstream the waste dump with pH rising. SO(4) decreases rapidly downstream direction. Copper, Zn and Co concentrations decrease with distance from the waste dump due to a dilution effect by the mixing of uncontaminated sediments. These elements, in particular, Zn are considerably elevated in sediment sample collected at the nearest distance to the waste dump. There is no doubt that such investigations can help to develop an appropriate water remediation plan.

  12. Marketing plan for business start-up

    OpenAIRE

    Kaisar, Jabed

    2016-01-01

    The marketing plan for the startup company concentrates on the affordable and effective marketing strategies for the new company with the limited budget for marketing. In this thesis, the shoe company named Jalkani is selected as the case study for the marketing plan. In the age of Internet, the marketing becomes more complex with the combination of the traditional advertising (paid advertisements in newspapers, billboard, or television) and the model digital marketing. The costs for each ...

  13. Diavik Waste Rock Project: Evolution of Mineral Weathering, Element Release, and Acid Generation and Neutralization during a Five-Year Humidity Cell Experiment

    Directory of Open Access Journals (Sweden)

    Jeff B. Langman

    2014-04-01

    Full Text Available A five-year, humidity-cell experiment was used to study the weathering evolution of a low-sulfide, granitic waste rock at 5 and 22 °C. Only the rock with the highest sulfide content (0.16 wt % released sufficient acid to overcome a limited carbonate acid-neutralization capacity and produce a substantial decline in pH. Leached SO4 and Ca quickly increased then decreased during the first two years of weathering. Sulfide oxidation continued to release acid and SO4 after carbonate depletion, resulting in an increase in acid-soluble elements, including Cu and Zn. With the dissolution of Al-bearing minerals, the pH stabilized above 4, and sulfide oxidation continued to decline until the end of the experiment. The variation in activation energy of sulfide oxidation correlates with changes in sulfide availability, where the lowest activation energies occurred during the largest releases of SO4. A decrease in sulfide availability was attributed to consumption of sulfide and weathered rims on sulfide grains that reduced the oxidation rate. Varying element release rates due to changing carbonate and sulfide availability provide identifiable geochemical conditions that can be viewed as neutralization sequences and may be extrapolated to the field site for examining the evolution of mineral weathering of the waste rock.

  14. Correlation of radioactive waste treatment costs and the environmental impact of waste effluents in the nuclear fuel cycle: reprocessing light-water reactor fuel. [Radiation dose commitment to human populations from radioactive effluents released to environment

    Energy Technology Data Exchange (ETDEWEB)

    Finney, B.C.; Blanco, R.E.; Dahlman, R.C.; Hill, G.S.; Kitts, F.G.; Moore, R.E.; Witherspoon, J.P.

    1976-10-01

    A cost/benefit study was made to determine the cost and effectiveness of radioactive waste (radwaste) treatment systems for decreasing the release of radioactive materials from a model nuclear fuel reprocessing plant which processes light-water reactor (LWR) fuels, and to determine the radiological impact (dose commitment) of the released materials on the environment. The study is designed to assist in defining the term as low as reasonably achievable in relation to limiting the release of radioactive materials from nuclear facilities. The base case model plant is representative of current plant technology and has an annual capacity of 1500 metric tons of LWR fuel. Additional radwaste treatment systems are added to the base case plant in a series of case studies to decrease the amounts of radioactive materials released and to reduce the radiological dose commitment to the population in the surrounding area. The cost for the added waste treatment operations and the corresponding dose commitments are calculated for each case. In the final analysis, radiological dose is plotted vs the annual cost for treatment of the radwastes. The status of the radwaste treatment methods used in the case studies is discussed. Much of the technology used in the advanced cases is in an early stage of development and is not suitable for immediate use. The methodology used in estimating the costs, and the radiological doses, detailed calculations, and tabulations are presented in Appendix A and ORNL-4992. This report is a revision of the original study (ORNL/TM-4901).

  15. The magnitude and relevance of the February 2014 radiation release from the Waste Isolation Pilot Plant repository in New Mexico, USA

    Energy Technology Data Exchange (ETDEWEB)

    Thakur, P. [Carlsbad Environmental Monitoring & Research Center, 1400 University Drive, Carlsbad, NM, 88220 (United States); Lemons, B.G.; White, C.R. [AECOM, Carlsbad Operations, Carlsbad, NM, 88220 (United States)

    2016-09-15

    After almost fifteen years of successful waste disposal operations, the first unambiguous airborne radiation release from the Waste Isolation Pilot Plant (WIPP) was detected beyond the site boundary on February 14, 2014. It was the first accident of its kind in the 15-year operating history of the WIPP. The accident released moderate levels of radioactivity into the underground air. A small but measurable amount of radioactivity also escaped to the surface through the ventilation system and was detected above ground. The dominant radionuclides released were americium and plutonium, in a ratio consistent with the known content of a breached drum. The radiation release was caused by a runaway chemical reaction inside a transuranic (TRU) waste drum which experienced a seal and lid failure, spewing radioactive materials into the repository. According to source-term estimation, approximately 2 to 10 Ci of radioactivity was released from the breached drum into the underground, and an undetermined fraction of that source term became airborne, setting off an alarm and triggering the closure of seals designed to force exhausting air through a system of filters including high-efficiency-particulate-air (HEPA) filters. Air monitoring across the WIPP site intensified following the first reports of radiation detection underground to determine the extent of impact to WIPP personnel, the public, and the environment, if any. This article attempts to compile and interpret analytical data collected by an independent monitoring program conducted by the Carlsbad Environmental Monitoring & Research Center (CEMRC) and by a compliance-monitoring program conducted by the WIPP's management and operating contractor, the Nuclear Waste Partnership (NWP), LLC., in response to the accident. Both the independent and the WIPP monitoring efforts concluded that the levels detected were very low and localized, and no radiation-related health effects among local workers or the public would be

  16. Influence of organic acids on kinetic release of chromium in soil contaminated with leather factory waste in the presence of some adsorbents.

    Science.gov (United States)

    Taghipour, Marzieh; Jalali, Mohsen

    2016-07-01

    In this study, batch experiments were conducted to investigate the effects of nanoparticles (NPs) (MgO, ZnO, TiO2) and clay minerals (bentonite, zeolite) on the release of chromium (Cr) from leather factory waste (LFW) and LFW treated soil using organic acids. Chromium release from all treatments was studied in the presence of citric acid, oxalic acid and CaCl2 solutions. The results showed that, in all treatments, organic acids released more Cr than inorganic salt (CaCl2). The release of Cr by citric acid was higher than that by oxalic acid. In LFW treated soil and LFW, the release of Cr from the all treatments with NPs was less than that from the clay mineral treatments. On the other hand, in the presence of organic acids, Cr release by NPs and clay minerals decreased. Two kinetic models including pseudo-first- and pseudo-second-order model were tested to describe the time dependent Cr release data. Among the kinetic models used, the pseudo-second-order model generally gave the best fits to experimental data. Before and after release experiments, Cr in LFW, treated LFW, control soil and LFW treated soils were fractionated. In all treatments, the greatest amounts of Cr were found in the residual fraction (RES). The organic acids were effective in reducing the exchangeable (EXC), bound to organic matter (OM) and bound to carbonate (CAR) fractions of Cr in all treatments, whereas, after release of Cr from treated soils, Cr remained mainly in the RES fraction. The application of NPs and clay minerals in soil led to a significant transformation of Cr from mobile fractions to the RES fraction. Therefore, organic ligands played a dominant role in mobility and bioavailability of Cr and the removal of Cr by adsorbents.

  17. Combining scenarios in a calculation of the overall probability distribution of cumulative releases of radioactivity from the Waste Isolation Pilot Plant, southeastern New Mexico

    Energy Technology Data Exchange (ETDEWEB)

    Tierney, M.S.

    1991-11-01

    The Waste Isolation Pilot Plant (WIPP), in southeastern New Mexico, is a research and development facility to demonstrate safe disposal of defense-generated transuranic waste. The US Department of Energy will designate WIPP as a disposal facility if it meets the US Environmental Protection Agency's standard for disposal of such waste; the standard includes a requirement that estimates of cumulative releases of radioactivity to the accessible environment be incorporated in an overall probability distribution. The WIPP Project has chosen an approach to calculation of an overall probability distribution that employs the concept of scenarios for release and transport of radioactivity to the accessible environment. This report reviews the use of Monte Carlo methods in the calculation of an overall probability distribution and presents a logical and mathematical foundation for use of the scenario concept in such calculations. The report also draws preliminary conclusions regarding the shape of the probability distribution for the WIPP system; preliminary conclusions are based on the possible occurrence of three events and the presence of one feature: namely, the events attempted boreholes over rooms and drifts,'' mining alters ground-water regime,'' water-withdrawal wells provide alternate pathways,'' and the feature brine pocket below room or drift.'' Calculation of the WIPP systems's overall probability distributions for only five of sixteen possible scenario classes that can be obtained by combining the four postulated events or features.

  18. CONSERVATION AREA START-UPS: COMBINING THEORY AND PRACTICE

    OpenAIRE

    NORMAN S. WRIGHT; JEFF CANEEN; NATHAN ALEXANDER; ANDREW GOMEZ

    2010-01-01

    Business start-ups by indigenous people in wildlife conservation areas are prone to failure. Funding issues have been identified as a contributing cause of the disappointing results. A great deal has been written about capital structure both in the start-up literature and the corporate literature, but the applicability of this research to small, indigenous start-ups in and around conservation areas is lacking. Although current practice dictates a reliance on equity, we apply the relevant corp...

  19. Plan for the Startup of HA-21I Furnace Operations at the Plutonium Finishing Plant (PFP)

    Energy Technology Data Exchange (ETDEWEB)

    WILLIS, H.T.

    2000-02-17

    Achievement of Thermal Stabilization mission elements require the installation and startup of three additional muffle furnaces for the thermal stabilization of plutonium and plutonium bearing materials at the Plutonium Finishing Plant (PFP). The release to operate these additional furnaces will require an Activity Based Startup Review. The conduct of the Activity Based Startup Review (ABSR) was approved by Fluor Daniel Hanford on October 15, 1999. This plan has been developed with the objective of identifying those activities needed to guide the controlled startup of five furnaces from authorization to unrestricted operations by adding the HA-211 furnaces in an orderly and safe manner after the approval to Startup has been given. The Startup Plan provides a phased approach that bridges the activities between the completion of the Activity Based Startup Review authorizing the use of the three additional furnaces and the unrestricted operation of the five thermal stabilization muffle furnaces. The four phases are: (1) the initiation of five furnace operations using three empty (simulated full) boat charges from HA-211 and two full charges from HC-21C; (2) three furnace operations (one full charge from HA-211 and two full charges from HC-21C); (3) four furnace operations (two full charges from HA-211 and two full charges from HC-21C); and (4) integrated five furnace operations and unrestricted operations. Phase 1 of the Plan will be considered as the cold runs. This Plan also provides management oversight and administrative controls that are to be implemented until unrestricted operations are authorized. It also provides a formal review process for ensuring that all preparations needed for full five furnace operations are completed and formally reviewed prior to proceeding to the increased activity levels associated with five furnace operations. Specific objectives include: (1) To ensure that activities are conducted in a safe manner. (2) To provide supplemental

  20. Replacement of Cross-Site Transfer System Startup Plan

    Energy Technology Data Exchange (ETDEWEB)

    Gerken, M.D.

    1996-01-01

    This Startup Plan provides a discussion of organizational responsibilities, work planning, quality assurance (QA), personnel qualifications, and testing requirements for the Cross-Site Transfer System.

  1. Effects of quartz, airborne particulates and fly ash fractions from a waste incinerator on elastase release by activated and nonactivated rabbit alveolar macrophages.

    Science.gov (United States)

    Gulyas, H; Labedzka, M; Schmidt, N; Gercken, G

    1988-01-01

    Elastase release from cultured, activated and nonactivated rabbit alveolar macrophages (AM) was investigated after stimulation by different environmentally related mineral dusts (50-1000 micrograms/10(6) cells). Eight different dusts were analyzed for element contents and grain size: one rural and three urban airborne dusts, a coarse and a fine fraction of a sieved waste incinerator fly ash, a sonicated coarse fly ash fraction, and the standard quartz dust DQ 12. The fine fly ash fraction, the sonicated coarse fly ash fraction, and the quartz dust DQ 12 enhanced elastase release by activated AM. Only one of the tested airborne dusts effected a comparable elastase release. The untreated coarse fraction of the fly ash did not cause a significant increase of extracellular elastase activities. Elastase release was dependent on particle numbers and chemical composition and correlated best with barium and tin contents. Nonactivated AM released higher elastase activities than activated AM at low-dose levels. The possible role of dust-induced elastase secretion in the pathogenesis of emphysema is discussed.

  2. From Jam to Start-up

    DEFF Research Database (Denmark)

    Bering Kjæhr, Emil; Lyngbye Hvid Jensen, Jane; Schoenau-Fog, Henrik

    2015-01-01

    Production workshops such as game jams are popular ways of letting participants acquire hands-on knowledge and experience in producing an artifact or game prototype in a very limited timespan. Some of the games made at these production workshops are later published with great success, and create...... the foundation for new start-up companies. There are, however, an even larger group of very creative and innovative games and artifacts with great potential that go unpublished. This potentially leads to a loss of entrepreneurial opportunities and ultimately the jobs and careers such games could have fostered...

  3. Experimental determination of the speciation, partitioning, and release of perrhenate as a chemical surrogate for pertechnetate from a sodalite-bearing multiphase ceramic waste form

    Energy Technology Data Exchange (ETDEWEB)

    Pierce, Eric M.; Lukens, Wayne W.; Fitts, Jeff. P.; Jantzen, Carol. M.; Tang, G.

    2013-12-01

    A key component to closing the nuclear fuel cycle is the storage and disposition of nuclear waste in geologic systems. Multiphase ceramic waste forms have been studied extensively as a potential host matrix for nuclear waste. Understanding the speciation, partitioning, and release behavior of radionuclides immobilized in multiphase ceramic waste forms is a critical aspect of developing the scientific and technical basis for nuclear waste management. In this study, we evaluated a sodalite-bearing multiphase ceramic waste form (i.e., fluidized-bed steam reform sodium aluminosilicate [FBSR NAS] product) as a potential host matrix for long-lived radionuclides, such as technetium (99Tc). The FBSR NAS material consists primarily of nepheline (ideally NaAlSiO4), anion-bearing sodalites (ideally M8[Al6Si6O24]X2, where M refers to alkali and alkaline earth cations and X refers to monovalent anions), and nosean (ideally Na8[AlSiO4]6SO4). Bulk X-ray absorption fine structure analysis of the multiphase ceramic waste form, suggest rhenium (Re) is in the Re(VII) oxidation state and has partitioned to a Re-bearing sodalite phase (most likely a perrhenate sodalite Na8[Al6Si6O24](ReO4)2). Rhenium was added as a chemical surrogate for 99Tc during the FBSR NAS synthesis process. The weathering behavior of the FBSR NAS material was evaluated under hydraulically unsaturated conditions with deionized water at 90 ?C. The steady-state Al, Na, and Si concentrations suggests the weathering mechanisms are consistent with what has been observed for other aluminosilicate minerals and include a combination of ion exchange, network hydrolysis, and the formation of an enriched-silica surface layer or phase. The steady-state S and Re concentrations are within an order of magnitude of the nosean and perrhenate sodalite solubility, respectively. The order of magnitude difference between the observed and predicted concentration for Re and S may be associated with the fact that the anion

  4. Experimental Determination of the Speciation, Partitioning, and Release of Perrhenate as a Chemical Surrogate for Pertechnetate from a Sodalite-Bearing Multiphase Ceramic Waste Form

    Energy Technology Data Exchange (ETDEWEB)

    Pierce, Eric M [ORNL; Lukens, Wayne W [Lawrence Berkeley National Laboratory (LBNL); Fitts, Jeffrey P [Princeton University; Tang, Guoping [ORNL; Jantzen, C M [Savannah River National Laboratory (SRNL)

    2013-01-01

    A key component to closing the nuclear fuel cycle is the storage and disposition of nuclear waste in geologic systems. Multiphase ceramic waste forms have been studied extensively as a potential host matrix for nuclear waste. Understanding the speciation, partitioning, and release behavior of radionuclides immobilized in multiphase ceramic waste forms is a critical aspect of developing the scientific and technical basis for nuclear waste management. In this study, we evaluated a sodalite-bearing multiphase ceramic waste form (i.e., fluidized-bed steam reform sodium aluminosilicate [FBSR NAS] product) as a potential host matrix for long-lived radionuclides, such as technetium (99Tc). The FBSR NAS material consists primarily of nepheline (ideally NaAlSiO4), anion-bearing sodalites (ideally M8[Al6Si6O24]X2, where M refers to alkali and alkaline earth cations and X refers to monovalent anions), and nosean (ideally Na8[AlSiO4]6SO4). Bulk x-ray absorption fine structure analysis of the multiphase ceramic waste form, suggest rhenium (Re) is in the Re(VII) oxidation state and has partitioned to a Re-bearing sodalite phase (most likely a perrhenate sodalite Na8[Al6Si6O24](ReO4)2). Rhenium was added as a chemical surrogate for 99Tc during the FBSR NAS synthesis process. The weathering behavior of the FBSR NAS material was evaluated under hydraulically unsaturated conditions with deionized water at 90 C. The steady-state Al, Na, and Si concentrations suggests the weathering mechanisms are consistent with what has been observed for other aluminosilicate minerals and include a combination of ion exchange, network hydrolysis, and the formation of an enriched-silica surface layer or phase. The steady-state S and Re concentrations are within an order of magnitude of the nosean and perrhenate sodalite solubility, respectively. The order of magnitude difference between the observed and predicted concentration for Re and S may be associated with the fact that the anion

  5. HIV gp120 inhibits the somatotropic axis: A possible GH-releasing hormone receptor mechanism for the pathogenesis of AIDS wasting

    OpenAIRE

    Mulroney, Susan E.; McDonnell, Kevin J.; Pert, Candace B.; Ruff, Michael R.; Resch, Zachary; Samson, Willis K.; Lumpkin, Michael D.

    1998-01-01

    AIDS is often associated with growth retardation in children and wasting in adults. The dissociated envelope protein of the HIV (HIV-1), gp120, can be found in significant concentrations in the parenchyma and cerebrospinal fluid of brains in infected individuals, even in the earliest stages of HIV-1 disease. On the basis of this and the fact that we observed pentapeptide sequence homology between GH-releasing hormone (GHRH) and the V2 receptor-binding region of gp120, we initiated experiments...

  6. Startup Time, Startup Power and Startup Loss in Reduced-voltage Startup of Induction Motor%异步电机降压起动的起动时间、起动功率和起动损耗

    Institute of Scientific and Technical Information of China (English)

    李梦达; 李明辉; 曹玉泉

    2011-01-01

    为了限制异步电机较大的起动电流,经常采用降压起动的方法.但目前对异步电机降压起动的问题研究较少.以电机理论为基础,利用电机的机械特性曲线,分析了异步电机降压Uσ起动时的起动时间、起动功率和起动损耗.设Uσ与额定电压UN之比为降压系数σ(0<σ<1),与额定电压UN起动时相比,降压Uσ起动时的起动时间tσ增大到1/σ2,起动功率△Pσ减小到1/σ2,起动损耗△W不变,降压起动不能节能.%In order to limit the larger starting current of induction motor, re duced-voltage startup is used frequently, but up to now, studies of reduced-voltage startup for induction motors have been relatively scarce.Therefore based on the electric theory, and using torque-speed characteristic curve of induction motor, the startup time, startup power and startup loss of induction motor are analyzed when the reduced-voltage Uσ startup.Set the ratio of Uσ to rated-voltage UN is reduced-voltage coefficient σ(0 < σ < 1 ), compared with the rated-voltageUN startup, can get that the reduced-voltage Uσ startup time tσincreased to 1/(σ2) times, startup power APσ reduced to 1/(σ2), startup loss △ W is unchanged, reduced-voltage startup can not be energy-saving.

  7. Construction and startup experience for Milliken FGD Retrofit Project

    Energy Technology Data Exchange (ETDEWEB)

    Harvilla, J.; Mahlmeister, M. [New York State Electric and Gas Corp., Binghamton, NY (United States); Buchanan, T.; Jackson, C. [Parsons Power Group, Inc., Reading, PA (United States); Watts, J. [USDOE, Pittsburgh Energy Technology Center, PA (United States)

    1996-12-01

    Under Round 4 of the U.S. Department of Energy`s Clean Coal Technology program, New York State Electric & Gas Corp. (NYSEG), in partnership with Saarbereg-Stebbins Engineering and Manufacturing Company, has retrofitted a formic acid enhanced forced oxidation wet limestone scrubber on Units 1 & 2 at the Milliken Steam Electric Station. Units 1 & 2 are 1950`s vintage Combustion Engineering tangentially fired pulverized coal units which are rated at nominal 150 MW each and operate in balanced draft mode. The FGD system for Unit 2 was placed into operation in January 1995 and the Unit 1 system in June, 1995. The project incorporates several unique aspects including low pH operation, a ceramic tile-lined cocurrent/countercurrent, split module absorber, a wet stack supported on the roof of the FGD building, and closed loop, zero liquid discharge operation producing commercial grade gypsum, and calcium chloride brine. The project objectives include 98% SO{sub 2} removal efficiency while burning high sulfur coal, the production of marketable byproducts to minimize solid waste disposal, zero wastewater discharge and space-saving design. The paper provides a brief overview of the project design, discusses construction and startup issues and presents early operating results. Process capital cost and economics of this design, procure and construct approach are reviewed relative to competing technologies.

  8. Release of chlorinated, brominated and mixed halogenated dioxin-related compounds to soils from open burning of e-waste in Agbogbloshie (Accra, Ghana).

    Science.gov (United States)

    Tue, Nguyen Minh; Goto, Akitoshi; Takahashi, Shin; Itai, Takaaki; Asante, Kwadwo Ansong; Kunisue, Tatsuya; Tanabe, Shinsuke

    2016-01-25

    Although complex mixtures of dioxin-related compounds (DRCs) can be released from informal e-waste recycling, DRC contamination in African e-waste recycling sites has not been investigated. This study examined the concentrations of DRCs including chlorinated, brominated, mixed halogenated dibenzo-p-dioxins/dibenzofurans (PCDD/Fs, PBDD/Fs, PXDD/Fs) and dioxin-like polychlorinated biphenyls (DL-PCBs) in surface soil samples from the Agbogbloshie e-waste recycling site in Ghana. PCDD/F and PBDD/F concentrations in open burning areas (18-520 and 83-3800 ng/g dry, respectively) were among the highest reported in soils from informal e-waste sites. The concentrations of PCDFs and PBDFs were higher than those of the respective dibenzo-p-dioxins, suggesting combustion and PBDE-containing plastics as principal sources. PXDFs were found as more abundant than PCDFs, and higher brominated analogues occurred at higher concentrations. The median total WHO toxic equivalent (TEQ) concentration in open burning soils was 7 times higher than the U.S. action level (1000 pg/g), with TEQ contributors in the order of PBDFs>PCDD/Fs>PXDFs. DRC emission to soils over the e-waste site as of 2010 was estimated, from surface soil lightness based on the correlations between concentrations and lightness, at 200mg (95% confidence interval 93-540 mg) WHO-TEQ over three years. People living in Agbogbloshie are potentially exposed to high levels of not only chlorinated but also brominated DRCs, and human health implications need to be assessed in future studies.

  9. Business Startups: Cultural-Economic Controversy

    Directory of Open Access Journals (Sweden)

    Nejat Erk

    2011-03-01

    Full Text Available The purpose of this paper is to examine whether national cultural differencesand/or economic, macroeconomic indicators are dominantin explaining business startups in selected EU countries. Among Hofstede’snational cultural differences, we have used the individualismcollectivenessindexmeasuring preference behavior that promotes one’sself interest, while the power distance index measures tolerance of citizensin terms of social inequality in terms of superiors or subordinates;the uncertainty avoidance index reflects tolerance towards uncertaintyand ambiguity among citizens, while the masculinity index measureswhether the society is male centered (Hofstede 2003. The last variablein the model related to culture is the corruption index (TransparencyInternational 2008, which reflects how sensitive the nation is towardscorruption. Among the macroeconomic indicators we have looked atwhether the firm birth rate in an economy is strongly influenced bythe given average wage rate, overall productivity level among nations,index for profitability and real per capita GDP growth. Findings showthat with some exclusion, cultural factors are as important as economicindicators in explaining national business startups. Towards this end wehave used factor and principle component analysis towards explainingthe strength of the relationship among the variables.

  10. HIV gp120 inhibits the somatotropic axis: A possible GH-releasing hormone receptor mechanism for the pathogenesis of AIDS wasting

    Science.gov (United States)

    Mulroney, Susan E.; McDonnell, Kevin J.; Pert, Candace B.; Ruff, Michael R.; Resch, Zachary; Samson, Willis K.; Lumpkin, Michael D.

    1998-01-01

    AIDS is often associated with growth retardation in children and wasting in adults. The dissociated envelope protein of the HIV (HIV-1), gp120, can be found in significant concentrations in the parenchyma and cerebrospinal fluid of brains in infected individuals, even in the earliest stages of HIV-1 disease. On the basis of this and the fact that we observed pentapeptide sequence homology between GH-releasing hormone (GHRH) and the V2 receptor-binding region of gp120, we initiated experiments to determine whether gp120 could affect GH secretion and growth in vivo and/or interact with anterior pituitary GHRH receptors in vitro. Although acute IV administration of gp120 in conscious rats had no effect on plasma GH levels, acute administration of gp120 (400 ng) into the brain significantly suppressed pulsatile GH release over a 6-h period compared with saline-injected controls. Furthermore, the putative gp120 antagonist, Peptide T (DAPTA), prevented the suppression of GH by gp120. In support of these in vivo findings, gp120 also significantly (P < 0.05) suppressed GHRH-stimulated GH release in static cultures of dispersed pituitary cells and from cells undergoing perifusion with the peptides. DAPTA prevented the GH suppression by gp120 in both of the pituitary cell paradigms. Furthermore, chronic administration of gp120 into the third ventricle significantly reduced body weight in juvenile rats, compared with saline-injected controls. Thus, gp120 appears to act both at the hypothalamus and pituitary to suppress GH release, and its action at these two locations is associated with a significant loss in body weight in chronically treated young animals. These findings may suggest a specific mechanism for the pathogenesis of wasting in HIV-1 patients that involves blockade of endogenous GHRH receptors by gp120. PMID:9465119

  11. Social capital of venture capitalists and start-up funding

    NARCIS (Netherlands)

    O.T. Alexy (Oliver); J.H. Block (Jörn); P.G. Sandner (Philipp); A.L.J. Ter Wal (Anne)

    2012-01-01

    textabstractHow does the social capital of venture capitalists (VCs) affect the funding of start-ups? By building on the rich social capital literature, we hypothesize a positive effect of VCs' social capital, derived from past syndication, on the amount of money that start-ups receive. Specifically

  12. Viral startup a guide to designing viral loops

    CERN Document Server

    Chen, Andrew

    2013-01-01

    Andrew Chen is a blogger and entrepreneur focused on consumer internet, metrics and user acquisition. He is an advisor/angel for early-stage startups including Appsumo, Cardpool (acquired by Safeway), Catchfree, Gravity, Mocospace, Launchbit, Qik (acquired by Skype), WeeWorld, Votizen, and is also a 500 Startups mentor.

  13. Genetic Counselors in Startup Companies: Redefining the Genetic Counselor Role.

    Science.gov (United States)

    Rabideau, Marina M; Wong, Kenny; Gordon, Erynn S; Ryan, Lauren

    2016-08-01

    Genetic counselors (GCs) have recently begun moving into non-clinic based roles in increasing numbers. A relatively new role for GCs is working for startup companies. Startups are newly established companies in the phase of developing and researching new scalable businesses. This article explores the experiences of four GCs working at different startup companies and aims to provide resources for GCs interested in learning more about these types of roles. The article describes startup culture, including a relatively flat organizational structure, quick product iterations, and flexibility, among other unique cultural characteristics. Financial considerations are described, including how to understand and evaluate a company's financial status, along with a brief explanation of alternate forms of compensation including stock options and equity. Specifically, the article details the uncertainties and rewards of working in a fast-paced startup environment that affords opportunities to try new roles and use the genetic counseling skill set in new ways. This article aims to aid GCs in determining whether a startup environment would be a good fit, learning how to evaluate a specific startup, and understanding how to market themselves for positions at startups.

  14. Strategies, Uncertainty and Performance of Small Business Startups

    NARCIS (Netherlands)

    A.M. van Gelderen (Marco); M. Frese (Michael); A.R. Thurik (Roy)

    2000-01-01

    textabstractPersonal strategies of owners/founders of small business startups are related to performance and to environmental uncertainty. This is done using a longitudinal data set of some 50 Dutch startups. The results suggest a dynamic process between strategy and performance. A discrimination is

  15. How Does Personal Bankruptcy Law Affect Start-ups?

    NARCIS (Netherlands)

    Cerqueiro, G.M.; Penas, M.F.

    2011-01-01

    We analyze the effect of changes in U.S. state personal exemptions on the financing structure and performance of a representative sample of start-ups. An increase in the amount of borrower’s personal wealth protected in bankruptcy reduces the availability of bank credit to all start-ups. Owners of u

  16. Start-up Costs, Taxes and Innovative Entrepreneurship

    NARCIS (Netherlands)

    P. Darnihamedani (Pourya); J.H. Block (Jörn); S.J.A. Hessels (Jolanda); A. Simonyan (Aram)

    2015-01-01

    markdownabstract__Abstract__ Prior research suggests that start-up costs and taxes negatively influence entry into entrepreneurship. Yet, no distinction is made regarding the type of entrepreneurship, particularly innovative versus non-innovative entrepreneurship. Start-up costs, being one-off

  17. Toxics Release Inventory (TRI)

    Data.gov (United States)

    U.S. Environmental Protection Agency — The Toxics Release Inventory (TRI) is a dataset compiled by the U.S. Environmental Protection Agency (EPA). It contains information on the release and waste...

  18. New Solutions to the Funding Dilemma of Technology Startups

    Directory of Open Access Journals (Sweden)

    Ali Kousari

    2011-05-01

    Full Text Available This article explores the current funding challenges facing technology startups and describes new models based on smaller investments and collective action. First, the advantages and disadvantages of traditional startup funding models are presented, with an emphasis on venture capital and angel investment. Next, an overview of existing seed funds, or seed accelerators, shows how entrepreneurs can leverage this approach to access subsequent rounds of funding and create successful ventures. Then, an overview of crowd funding is provided, including examples of companies that have adopted this approach to funding startups and their founders. Finally, the article presents the basis of a new approach that uses crowd funding as means of attracting investors to collectives. In these business ecosystems, startups are exposed to less risk and investors can benefit from attractive returns by investing in these promising startups.

  19. Impact of startup scheme on Francis runner life expectancy

    Energy Technology Data Exchange (ETDEWEB)

    Gagnon, M; Tahan, S A; Bocher, P [Department of Mechanical Engineering, Ecole de technologie superieure (ETS) 1100, rue Notre-Dame Ouest, Montreal (Canada); Thibault, D, E-mail: martin.gagnon.8@ens.etsmtl.c [Institut de recherche d' Hydro-Quebec (IREQ), 1800, boul. Lionel-Boulet, Varennes, J3X 1S1 (Canada)

    2010-08-15

    Francis runners are subject to complex dynamic forces which might lead to eventual blade cracking and the need for corrective measure. Damage due to cracks in runner blades are usually not a safety issues but might generate unexpected down time and high repair cost. Avoiding the main damaging operating conditions is often the only option left to plant operators to maximize the life expectancy of their runner. The startup scheme is one of the available parameter which is controlled by the end user and could be used to minimize the damage induced to the runner. In this study, two startup schemes have been used to investigate life expectancy of Francis runner using in situ measurements. The results obtained show that the induced damage during the startup event could be significantly reduced with change to the startup scheme. In our opinion, an optimization of the startup scheme with regard to fatigue damage could extend significantly the life expectancy and the reliability of Francis runner.

  20. Studies on impact of release of liquid industrial waste from soda ash industry in the nearshore water of north Gujarat

    Digital Repository Service at National Institute of Oceanography (India)

    Zingde, M.D.

    ). The impacts of these wastes on the water and sediment quality of the receiving waters are discussed. Due to the density inhibited mixing the effluents tend to spread into a kilometre long milky white patch with high levels of pH, suspended solids and ammonia...

  1. Comparing Titanium Release from Ceramic Tiles using a waste material characterization test - Influence of Calcium and Organic Matter concentrations

    DEFF Research Database (Denmark)

    Heggelund, Laura Roverskov; Hansen, Steffen Foss; Astrup, Thomas Fruergaard

    2015-01-01

    Nanomaterials are beneficial in the building industry to enhance or add certain features to commonly used materials. One example is the use of nano-titanium dioxide in the surface coating of ceramic tiles, to make the tiles surface self-cleaning. At the end of life stage, ceramic tiles might...... to assess if nano-titanium dioxide coated ceramic tiles are suitable for depositing in a landfill or not. Specifically, we used compliance batch test method, which is a simple test evaluating the release from a solid material to an aqueous media during 24 hrs. If nano-Ti particles are released from solid...... of the organic matter to fully cover the surface of the particles. We evaluated the titanium release from identical ceramic tiles - with and without a nano-titanium dioxide coating - and varied the concentrations of calcium chloride (100-500 mg/l) and humic acid (25-100 mg/l). The titanium release was quantified...

  2. Challenges and methodology for safety analysis of a high-level waste tank with large periodic releases of flammable gas

    Energy Technology Data Exchange (ETDEWEB)

    Edwards, J.N.; Pasamehmetoglu, K.O.; White, J.R. [Los Alamos National Lab., NM (United States); Stewart, C.W. [Pacific Northwest Lab., Richland, WA (United States)

    1994-07-01

    Tank 241-SY-101, located at the Department of Energy Hanford Site, has periodically released up to 10,000 ft{sup 3} of flammable gas. This release has been one of the highest-priority DOE operational safety problems. The gases include hydrogen and ammonia (fuels) and nitrous oxide (oxidizer). There have been many opinions regarding the controlling mechanisms for these releases, but demonstrating an adequate understanding of the problem, selecting a mitigation methodology, and preparing the safety analysis have presented numerous new challenges. The mitigation method selected for the tank was to install a pump that would mix the tank contents and eliminate the sludge layer believed to be responsible for the gas retention and periodic releases. This report will describe the principal analysis methodologies used to prepare the safety assessment for the installation and operation of the pump, and because this activity has been completed, it will describe the results of pump operation.

  3. Start-up Strategy for Continuous Bioreactors

    Directory of Open Access Journals (Sweden)

    A.C. da Costa

    1997-06-01

    Full Text Available Abstract - The start-up of continuous bioreactors is solved as an optimal control problem. The choice of the dilution rate as the control variable reduces the dimension of the system by making the use of the global balance equation unnecessary for the solution of the optimization problem. Therefore, for systems described by four or less mass balance equations, it is always possible to obtain an analytical expression for the singular arc as a function of only the state variables. The steady state conditions are shown to satisfy the singular arc expression and, based on this knowledge, a feeding strategy is proposed which leads the reactor from an initial state to the steady state of maximum productivity

  4. STEADY-STATE FLAMMABLE GAS RELEASE RATE CALCULATION AND LOWER FLAMMABILITY LEVEL EVALUATION FOR HANFORD TANK WASTE

    Energy Technology Data Exchange (ETDEWEB)

    HU TA

    2007-10-26

    Assess the steady-state flammability level at normal and off-normal ventilation conditions. The methodology of flammability analysis for Hanford tank waste is developed. The hydrogen generation rate model was applied to calculate the gas generation rate for 177 tanks. Flammability concentrations and the time to reach 25% and 100% of the lower flammability limit, and the minimum ventilation rate to keep from 100 of the LFL are calculated for 177 tanks at various scenarios.

  5. Innovative Startup-Projects: Experience, Evaluation, Implementation Contradictions

    Directory of Open Access Journals (Sweden)

    Inshakov Maksim Olegovich

    2015-09-01

    Full Text Available Innovative companies in the conditions of global post-crisis economic recovery and increased economic activity become again a promising area for investments of large investment and venture capital funds, venture divisions of large transnational corporations, business angels and other private investors. This is confirmed by the data on the increase in the volume of venture capital market in the US and Europe and on a significant increase in the cost of the leading foreign and Russian start-up companies which are rated as of 2014 in the present article. The comparative analysis of the leading Russian and foreign start-ups showed the prevalence of companies engaged in the field of IT-Internet-Mobile and focused on the provision of various kinds of innovative services to consumers among the foreign participants of the rating. Among Russian startups-winners the companies of technological orientation (biological, medical, and “clean” technologies dominate. They reflect the increasing importance of start-ups in the innovative development of the Russian economy. Participation in such competitions and ratings is a favorable factor of promoting start-ups, increasing awareness of potential investors and consumers of start-up products. The importance of start-ups formation and the development of effective regional and national innovation systems update the studies related to the identification of the fundamental contradictions in the activities of Russian start-ups and to the development of recommendations for their resolution. The article identifies the key issues of economic, organizational, informational and marketing character causing the collapse of start-up projects in the Russian economy in modern conditions.

  6. Skill Heterogeneity in Startups and its Development over Time

    DEFF Research Database (Denmark)

    Kaiser, Ulrich; Müller, Bettina

    2015-01-01

    at startup and how it evolves as the new venture matures. We use the population of Danish startups that were established in 1998 and track them until 2001. Main findings are that teams are relatively more homogeneous at startup compared to our benchmark, indicating that difficulties associated with workforce...... heterogeneity (like affective conflict or coordination cost) as well as “homophily” (people’s inclination to bound with others with similar characteristics) may overweigh the benefits of heterogeneity. While workforce heterogeneity does increase over time, the increase is smaller compared to our benchmark...

  7. University Knowledge Spillovers & Regional Start-up Rates

    DEFF Research Database (Denmark)

    Hellerstedt, Karin; Wennberg, Karl; Frederiksen, Lars

    2014-01-01

    on entrepreneurship, we develop a theoretical framework which captures how both supply- and demand-side factors mold the regional bedrock for start-ups in knowledge-intensive industries. Using multilevel data of all knowledge-intensive start-ups across 286 Swedish municipalities between 1994 and 2002 we demonstrate...... demand-side and supply-side context than is the case for high-tech start-ups in general. Our study contributes to the growing stream of research that explains entrepreneurial activity as shaped by contextual factors, most notably academic institutions, such as universities that contribute to knowledge...

  8. Product innovation and commercialization in lean global start-ups

    DEFF Research Database (Denmark)

    Tanev, Stoyan; Rasmussen, Erik Stavnsager; Zijdemans, Erik

    2015-01-01

    The paper examines the distinctive characteristics of product innovation and commercialization in Lean Global Start-up (LGS) – new technology firms which have adopted a lean and global path from or near to their inception. It suggests an uncertainty vs risk framework which allows integrating two...... research streams – Born Global (BG) firms and lean start-ups. In addition to its integrative theoretical value, the paper offers insights for lean start-up managers dealing with the challenges of a global start....

  9. Study of the effects of waste disposal in a selected rock-salt formation (SESAM). Advective transport of released particles

    NARCIS (Netherlands)

    Oostrom M; Leijnse A; Beusen AHW; Sauter FJ

    1993-01-01

    A number of particle tracking simulations have been carried out for radionuclide particles which are hypothetically released from the Zuidwending diapir. The particle tracking code used was METROPART, a postprocessor of the METROPOL model. Two-dimensional METROPOL-3 simulations and subsequent

  10. Hanford Tanks 241-C-203 and 241-C-204: Residual Waste Contaminant Release Model and Supporting Data

    Energy Technology Data Exchange (ETDEWEB)

    Deutsch, William J.; Krupka, Kenneth M.; Lindberg, Michael J.; Cantrell, Kirk J.; Brown, Christopher F.; Schaef, Herbert T.

    2004-10-28

    This report describes the development of release models for key contaminants that are present in residual sludge remaining after closure of Hanford Tanks 241-C-203 (C-203) and 241-C-204 (C-204). The release models were developed from data generated by laboratory characterization and testing of samples from these two tanks. Key results from this work are (1) future releases from the tanks of the primary contaminants of concern (99Tc and 238U) can be represented by relatively simple solubility relationships between infiltrating water and solid phases containing the contaminants; and (2) high percentages of technetium-99 in the sludges (20 wt% in C-203 and 75 wt% in C-204) are not readily water leachable, and, in fact, are very recalcitrant. This is similar to results found in related studies of sludges from Tank AY-102. These release models are being developed to support the tank closure risk assessments performed by CH2M HILL Hanford Group, Inc., for the U.S. Department of Energy.

  11. Hanford Tanks 241-C-203 and 241 C 204: Residual Waste Contaminant Release Model and Supporting Data

    Energy Technology Data Exchange (ETDEWEB)

    Deutsch, William J.; Krupka, Kenneth M.; Lindberg, Michael J.; Cantrell, Kirk J.; Brown, Christopher F.; Schaef, Herbert T.

    2007-05-23

    This report was revised in May 2007 to correct 90Sr values in Chapter 3. The changes were made on page 3.9, paragraph two and Table 3.10; page 3.16, last paragraph on the page; and Tables 3.21 and 3.31. The rest of the text remains unchanged from the original report issued in October 2004. This report describes the development of release models for key contaminants that are present in residual sludge remaining after closure of Hanford Tanks 241-C-203 (C-203) and 241-C-204 (C-204). The release models were developed from data generated by laboratory characterization and testing of samples from these two tanks. Key results from this work are (1) future releases from the tanks of the primary contaminants of concern (99Tc and 238U) can be represented by relatively simple solubility relationships between infiltrating water and solid phases containing the contaminants; and (2) high percentages of technetium-99 in the sludges (20 wt% in C-203 and 75 wt% in C-204) are not readily water leachable, and, in fact, are very recalcitrant. This is similar to results found in related studies of sludges from Tank AY-102. These release models are being developed to support the tank closure risk assessments performed by CH2M HILL Hanford Group, Inc., for the U.S. Department of Energy.

  12. Study of the effects of waste disposal in a selected rock-salt formation (SESAM). Advective transport of released particles

    NARCIS (Netherlands)

    Oostrom M; Leijnse A; Beusen AHW; Sauter FJ

    1993-01-01

    A number of particle tracking simulations have been carried out for radionuclide particles which are hypothetically released from the Zuidwending diapir. The particle tracking code used was METROPART, a postprocessor of the METROPOL model. Two-dimensional METROPOL-3 simulations and subsequent METR

  13. Decision Enhancement Services for Small and Medium Enterprise Start-Ups in Uganda

    NARCIS (Netherlands)

    Sol, H G; Basaza, Habinka; Sprague, Ralph H.

    2012-01-01

    While start-up firms create a substantial economic impact on most economies, the failure rate of start-up firms seems to remain high due to inadequate agile decision services. Deciding to start-up mining Small and Medium Enterprises (SME) is a challenging task in Uganda. Research on SME start-up sup

  14. Industrial release of fluoroquinolones (FQs) in the waste water bodies with their associated ecological risk in Pakistan.

    Science.gov (United States)

    Riaz, Luqman; Mahmood, Tariq; Kamal, Atif; Shafqat, Mateen; Rashid, Audil

    2017-06-01

    The unchecked production and use of fluoroquinolones (FQs) for the treatment of infections in human and livestock has increased in Pakistan, which resulted in large amount of antibiotics in water bodies. In the current study, the prevalence and associated ecological risk of three FQs were investigated in waste-water bodies and sludge samples of Kahuta and Hattar industrial zones. The average concentrations of ciprofloxacin (CIP), enrofloxacin (ENR) and levofloxacin (LEV) in the waste-water samples were slightly higher in Kahuta (i.e. 58, 32.9, and 36.7μgL(-1) respectively), than those in Hattar sites (i.e. 42.1, 41.2, and 48.9μgL(-1) respectively). However, the concentrations of CIP, ENR and LEV in the sludge samples were significantly higher (i.e. 159; 153 and 164μgkg(-1) respectively) in Hattar sites, compared to those in Kahuta sites (i.e. 129, 58 and 91μgkg(-1) respectively). The uses of FQs in the health sector resulted in water pollution and poses the ecological risk to aquatic organisms. The individual risk associated with CIP was highest in Kahuta industrial sites for green algae ranging (2900-9100) followed by M. aeruginosa (5800-18200), cyanobacteria (580-18204) and invertebrates (24.2-75.8). These values suggested that the prevalence of antibiotics in the waste-disposal sites could be potential risk for the aquatic ecosystem, and harmful to biodiversity. Copyright © 2017 Elsevier B.V. All rights reserved.

  15. Some results of long-term investigation population exposed as a result of release of radioactive wastes into the Techa River in Southern Urals

    Energy Technology Data Exchange (ETDEWEB)

    Degteva, M.O.; Kozheurov, V.P.; Vorobiova, M.I. [Ural research Center for Radiation Medicine, Chelyabinsk (Russian Federation)

    1992-06-01

    This paper describes results of a long-term investigation of a population exposed to radioactive waste release in 1949-1956 into the Techa River in the Southern Urals. Systematic measurements of radionuclide concentration in the river waters, sediments, and floodplain soils and measurements of exposure gamma dose rates as well as studies of the radionuclide composition in the contaminated areas began in the summer of 1951. As a result of the contamination, 124,000 residents were exposed to radiation and 28,100 received significant doses in terms of health effect potential. Covered results include the following: estimation of external radiation doses; content of strontium-90 in humans and estimation of radionuclide ingestion rates; age-dependent model of strontium metabolism in the human body; evaluation of doses of internal irradiation; distribution of exposed population according to accumulated doses. 11 refs; 15 figs.

  16. Ecotoxicological screen of Potential Release Site 50-006(d) of Operable Unit 1147 of Mortandad Canyon and relationship to the Radioactive Liquid Waste Treatment Facilities project

    Energy Technology Data Exchange (ETDEWEB)

    Gonzales, G.J.; Newell, P.G.

    1996-04-01

    Potential ecological risk associated with soil contaminants in Potential Release Site (PRS) 50-006(d) of Mortandad Canyon at the Los Alamos National Laboratory was assessed by performing an ecotoxicological risk screen. The PRS surrounds Outfall 051, which discharges treated effluent from the Radioactive Liquid Waste Treatment Facility. Discharge at the outfall is permitted under the Clean Water Act National Pollution Discharge Elimination System. Radionuclide discharge is regulated by US Department of Energy (DOE) Order 5400.5. Ecotoxicological Screening Action Levels (ESALSs) were computed for nonradionuclide constituents in the soil, and human risk SALs for radionuclides were used as ESALs. Within the PRS and beginning at Outfall 051, soil was sampled at three points along each of nine linear transects at 100-ft intervals. Soil samples from 3 depths for each sampling point were analyzed for the concentration of a total of 121 constituents. Only the results of the surface sampling are reported in this report.

  17. Development of scenarios for long-term release of radionuclides from the proposed waste isolation pilot plant in southeastern New Mexico

    Energy Technology Data Exchange (ETDEWEB)

    Bingham, F.W.; Barr, G.E.

    1979-01-01

    As fault-tree analysis had its faults, the WIPP group switched its attention to the construction of event trees and of scenarios from the cut sets of these event trees. The scenarios were grouped into three classes for computer modeling: those that expose waste directly to the biosphere, those that begin with water flow between two aquifers at the site, and those that begin with water flow from only one aquifer. Each of the scenarios can be modeled by one of four general models. The current analyses of the long-term effects of the WIPP repository are derived from these models. Predicted doses from these hypothetical releases fall far below those from natural background radiation. (DLC)

  18. Energy-Saving Start-Up of Firing System in Anode Baking Furnace%阳极焙烧炉火焰系统的节能启动

    Institute of Scientific and Technical Information of China (English)

    李勇刚

    2012-01-01

    Aiming at the deficiencies of the traditional cold boiler ignition start-up method of anode baking furnace firing system, the energy-saving start-up method, by which firing system was igniting at high temperature by using the waste heat, was presented and applied. The practical result indicated that the method could effectively shorten the start-up time and save a lot of fuel consumption.%针对阳极焙烧炉火焰系统传统的冷炉点火启动方法存在的不足,提出并应用了利用余热进行高温点火的节能启动方法.实践结果表明,该方法能有效缩短烘炉启动过程时间,大幅减少燃料消耗.

  19. Participatory Savings And Borrowing For Start-Up And ...

    African Journals Online (AJOL)

    Journal of Agriculture and Social Research (JASR) ... Participatory Savings And Borrowing For Start-Up And Recapitalization Needs: Farmers ... be considered for more loans whenever they meet up with the conditions for such new contracts.

  20. CERN confident of LHC start-up in 2007

    CERN Multimedia

    2007-01-01

    "Delegates attending the 140th meeting of CERN Council heard a confident report from the Laboratory about the scheduled start-up of the world's highest energy particle accelerator, the Large Hadron Collier (LHC), in 2007." (1 page)

  1. Start-up Funding via Equity Crowdfunding in Germany

    DEFF Research Database (Denmark)

    Angerer, Martin; Brem, Alexander; Kraus, Sascha

    2017-01-01

    Entrepreneurs often struggle to find sufficient funding for their start-ups. A relatively new way for companies to attract capital is via an internet platform, locating investors who in return receive something in return for their ventures. Equity crowdfunding is one of several types of crowdfund......Entrepreneurs often struggle to find sufficient funding for their start-ups. A relatively new way for companies to attract capital is via an internet platform, locating investors who in return receive something in return for their ventures. Equity crowdfunding is one of several types...... of crowdfunding, and is also known as crowdinvesting in the German-speaking realm. This article predominantly advances the scientific knowledge regarding the success factors of equity crowdfunding for German start-ups. The study conducted nine qualitative interviews with start-ups and crowdinvesting platforms...

  2. Start-up Funding via Equity Crowdfunding in Germany

    DEFF Research Database (Denmark)

    Angerer, Martin; Brem, Alexander; Kraus, Sascha

    2017-01-01

    Entrepreneurs often struggle to find sufficient funding for their start-ups. A relatively new way for companies to attract capital is via an internet platform, locating investors who in return receive something in return for their ventures. Equity crowdfunding is one of several types...... of crowdfunding, and is also known as crowdinvesting in the German-speaking realm. This article predominantly advances the scientific knowledge regarding the success factors of equity crowdfunding for German start-ups. The study conducted nine qualitative interviews with start-ups and crowdinvesting platforms....... Its first result is that German start-ups select crowdinvesting because (1) it is a funding opportunity and (2) it has an expected marketing effect. To organize the results of relevant success factors, the Crowdinvesting Success Model was designed by the researchers. This supports German entrepreneurs...

  3. Intellectual property and financing strategies for technology startups

    CERN Document Server

    Halt, Jr , Gerald B; Stiles, Amber R; Fesnak, Robert

    2017-01-01

    This book offers a comprehensive, easy to understand guide for startup entities and developing companies, providing insight on the various sources of funding that are available, how these funding sources are useful at each stage of a company’s development, and offers a comprehensive intellectual property strategy that parallels each stage of development. The IP strategies offered in this book take into consideration the goals that most startups and companies have at each stage of development, as well as the limitations that exist at each stage (i.e., limited available resources earmarked for intellectual property asset development), and provides solutions that startups and companies can implement to maximize their return on intellectual property investments. This book also includes a number of descriptive examples, case studies and scenarios to illustrate the topics discussed, and is intended for use by startups and companies across all industries. Readers will garner an appreciation for the value that inte...

  4. University Start-ups: A Better Business Model

    Science.gov (United States)

    Dehn, J.; Webley, P. W.

    2015-12-01

    Many universities look to start-up companies as a way to attract faculty, supporting research and students as traditional federal sources become harder to come by. University affiliated start-up companies can apply for a broader suite of grants, as well as market their services to a broad customer base. Often university administrators see this as a potential panacea, but national statistics show this is not the case. Rarely do universities profit significantly from their start-ups. With a success rates of around 20%, most start-ups end up costing the university money as well as faculty-time. For the faculty, assuming they want to continue in academia, a start-up is often unattractive because it commonly leads out of academia. Running a successful business as well as maintaining a strong teaching and research load is almost impossible to do at the same time. Most business models and business professionals work outside of academia, and the models taught in business schools do not merge well in a university environment. To mitigate this a new business model is proposed where university start-ups are aligned with the academic and research missions of the university. A university start-up must work within the university, directly support research and students, and the work done maintaining the business be recognized as part of the faculty member's university obligations. This requires a complex conflict of interest management plan and for the companies to be non-profit in order to not jeopardize the university's status. This approach may not work well for all universities, but would be ideal for many to conserve resources and ensure a harmonious relationship with their start-ups and faculty.

  5. Subsidizing Start-Ups: Policy Targeting and Policy Effectiveness

    OpenAIRE

    Kösters, Sarah

    2009-01-01

    Start-up subsidies are a frequently employed policy instrument, the use of which is justified by alleged market failure resulting from positive external effects and capital market imperfections. This article investigates whether the allocation of subsidies reflects a policy focus on addressing these market failure occurrences. However, using survey data from the East German state of Thuringia, logistic regressions reveal a rather random subsidization of start-ups. Furthermore, propensity scor...

  6. GUERRILLA MARKETING : A creative marketing method for start-ups

    OpenAIRE

    Zujewska, Barbara

    2014-01-01

    The objective of this thesis work was to introduce guerrilla marketing as a valuable marketing method for small and medium size startup companies. The thesis presents the theoretical studies on the subject based on literature and case studies. The practical use of the theory is demonstrated in the marketing plan based on guerrilla marketing approach. The marketing plan was written based on the example of an existing startup company, mCASH. The company is located in Oslo, Norway. The thesis...

  7. Start-ups, Venture Capitalists and the Capital Gains Tax

    OpenAIRE

    Keuschnigg, Christian; Nielsen, Søren Bo

    2004-01-01

    A model of start-up finance with double moral hazard is proposed. Entrepreneurs have ideas but lack their own resources as well as commercial experience. Venture capitalists provide start-up finance and managerial support. Both types of agents thus jointly contribute to the firm's success, but neither type's effort is verifiable. We find that the market equilibrium is biased towards inefficiently low venture capital support. In this situation, the capital gains tax is particularly harmful. Th...

  8. Start-up Costs, Taxes and Innovative Entrepreneurship

    OpenAIRE

    Darnihamedani, Pourya; Block, Jörn; Hessels, Jolanda; Simonyan, Aram

    2015-01-01

    markdownabstract__Abstract__ Prior research suggests that start-up costs and taxes negatively influence entry into entrepreneurship. Yet, no distinction is made regarding the type of entrepreneurship, particularly innovative versus non-innovative entrepreneurship. Start-up costs, being one-off costs, may reduce the entry of entrepreneurs whose ideas are not very promising, thus increasing the proportion of innovative entrepreneurs. Taxes, being recurring costs, may reduce the “prize” of innov...

  9. Giving start-ups a helping hand

    CERN Multimedia

    2008-01-01

    The French-Swiss foundation for research and technology (FFSRT) joined forces with CERN to organise an information day on setting up new businesses, at the Globe of Science and Innovation. The participants heard talks by entrepreneurs who started out at CERN, sharing their experiences and difficulties.CERN is a hot-bed of high-tech skills and know-how, and the Organization works actively to transfer this expertise to society. Some such innovations can lead to new business start-ups, but it can be extremely difficult to obtain the information and support you need to find your way through the inevitable administrative labyrinth. By opening its doors to the Fondation franco-suisse pour la recherche et la technologie (FFSRT) and hosting this "Entrepreneurial Day" on 7 March, CERN has clearly flagged its desire to assist budding entrepreneurs. The day was jointly kicked off by Olga Hooft, General Manager of the FFSRT, and Maximilian Metzger, CERN’s Se...

  10. High-level waste management technology program plan

    Energy Technology Data Exchange (ETDEWEB)

    Harmon, H.D.

    1995-01-01

    The purpose of this plan is to document the integrated technology program plan for the Savannah River Site (SRS) High-Level Waste (HLW) Management System. The mission of the SRS HLW System is to receive and store SRS high-level wastes in a see and environmentally sound, and to convert these wastes into forms suitable for final disposal. These final disposal forms are borosilicate glass to be sent to the Federal Repository, Saltstone grout to be disposed of on site, and treated waste water to be released to the environment via a permitted outfall. Thus, the technology development activities described herein are those activities required to enable successful accomplishment of this mission. The technology program is based on specific needs of the SRS HLW System and organized following the systems engineering level 3 functions. Technology needs for each level 3 function are listed as reference, enhancements, and alternatives. Finally, FY-95 funding, deliverables, and schedules are s in Chapter IV with details on the specific tasks that are funded in FY-95 provided in Appendix A. The information in this report represents the vision of activities as defined at the beginning of the fiscal year. Depending on emergent issues, funding changes, and other factors, programs and milestones may be adjusted during the fiscal year. The FY-95 SRS HLW technology program strongly emphasizes startup support for the Defense Waste Processing Facility and In-Tank Precipitation. Closure of technical issues associated with these operations has been given highest priority. Consequently, efforts on longer term enhancements and alternatives are receiving minimal funding. However, High-Level Waste Management is committed to participation in the national Radioactive Waste Tank Remediation Technology Focus Area. 4 refs., 5 figs., 9 tabs.

  11. BLT-MS (Breach, Leach, and Transport -- Multiple Species) data input guide. A computer model for simulating release of contaminants from a subsurface low-level waste disposal facility

    Energy Technology Data Exchange (ETDEWEB)

    Sullivan, T.M.; Kinsey, R.R.; Aronson, A.; Divadeenam, M. [Brookhaven National Lab., Upton, NY (United States); MacKinnon, R.J. [Brookhaven National Lab., Upton, NY (United States)]|[Ecodynamics Research Associates, Inc., Albuquerque, NM (United States)

    1996-11-01

    The BLT-MS computer code has been developed, implemented, and tested. BLT-MS is a two-dimensional finite element computer code capable of simulating the time evolution of concentration resulting from the time-dependent release and transport of aqueous phase species in a subsurface soil system. BLT-MS contains models to simulate the processes (water flow, container degradation, waste form performance, transport, and radioactive production and decay) most relevant to estimating the release and transport of contaminants from a subsurface disposal system. Water flow is simulated through tabular input or auxiliary files. Container degradation considers localized failure due to pitting corrosion and general failure due to uniform surface degradation processes. Waste form performance considers release to be limited by one of four mechanisms: rinse with partitioning, diffusion, uniform surface degradation, or solubility. Radioactive production and decay in the waste form are simulated. Transport considers the processes of advection, dispersion, diffusion, radioactive production and decay, reversible linear sorption, and sources (waste forms releases). To improve the usefulness of BLT-MS a preprocessor, BLTMSIN, which assists in the creation of input files, and a post-processor, BLTPLOT, which provides a visual display of the data have been developed. This document reviews the models implemented in BLT-MS and serves as a guide to creating input files for BLT-MS.

  12. Effect of transport-pathway simplifications on projected releases of radionuclides from a nuclear waste repository (Sweden)

    Science.gov (United States)

    Selroos, Jan-Olof; Painter, Scott L.

    2012-12-01

    The Swedish Nuclear Fuel and Waste Management Company has recently submitted an application for a license to construct a final repository for spent nuclear fuel, at approximately 500 m depth in crystalline bedrock. Migration pathways through the geosphere barrier are geometrically complex, with segments in fractured rock, deformation zones, backfilled tunnels, and near-surface soils. Several simplifications of these complex migration pathways were used in the assessments of repository performance that supported the license application. Specifically, in the geosphere transport calculations, radionuclide transport in soils and tunnels was neglected, and deformation zones were assumed to have transport characteristics of fractured rock. The effects of these simplifications on the projected performance of the geosphere barrier system are addressed. Geosphere performance is shown to be sensitive to how transport characteristics of deformation zones are conceptualized and incorporated into the model. Incorporation of advective groundwater travel time within backfilled tunnels reduces radiological dose from non-sorbing radionuclides such as I-129, while sorption in near-surface soils reduces radiological doses from sorbing radionuclides such as Ra-226. These results help quantify the degree to which geosphere performance was pessimistically assessed, and provide some guidance on how future studies to reduce uncertainty in geosphere performance may be focused.

  13. Soil retention of hexavalent chromium released from construction and demolition waste in a road-base-application scenario.

    Science.gov (United States)

    Butera, Stefania; Trapp, Stefan; Astrup, Thomas F; Christensen, Thomas H

    2015-11-15

    We investigated the retention of Cr(VI) in three subsoils with low organic matter content in laboratory experiments at concentration levels relevant to represent leachates from construction and demolition waste (C&DW) reused as unbound material in road construction. The retention mechanism appeared to be reduction and subsequent precipitation as Cr(III) on the soil. The reduction process was slow and in several experiments it was still proceeding at the end of the six-month experimental period. The overall retention reaction fit well with a second-order reaction governed by actual Cr(VI) concentration and reduction capacity of the soil. The experimentally determined reduction capacities and second-order kinetic parameters were used to model, for a 100-year period, the one-dimensional migration of Cr(VI) in the subsoil under a layer of C&DW. The resulting Cr(VI) concentration would be negligible below 7-70 cm depth. However, in rigid climates and with high water infiltration through the road pavement, the reduction reaction could be so slow that Cr(VI) might migrate as deep as 200 cm under the road. The reaction parameters and the model can form the basis for systematically assessing under which scenarios Cr(VI) from C&DW could lead to an environmental issue for ground- and receiving surface waters. Copyright © 2015 Elsevier B.V. All rights reserved.

  14. On the Impact of the Fuel Dissolution Rate Upon Near-Field Releases From Nuclear Waste Disposal

    Directory of Open Access Journals (Sweden)

    A Pereira

    2016-09-01

    Full Text Available Calculations of the impact of the dissolution of spent nuclear fuel on the release from a damaged canister in a KBS-3 repository are presented. The dissolution of the fuel matrix is a complex process and the dissolution rate is known to be one of the most important parameters in performance assessment models of the near-field of a geological repository. A variability study has been made to estimate the uncertainties associated with the process of fuel dissolution. The model considered in this work is a 3D model of a KBS-3 copper canister. The nuclide used in the calculations is Cs-135. Our results confirm that the fuel degradation rate is an important parameter, however there are considerable uncertainties associated with the data and the conceptual models. Consequently, in the interests of safety one should reduce, as far as possible, the uncertainties coupled to fuel degradation.

  15. INEEL Subregional Conceptual Model Report Volume 3: Summary of Existing Knowledge of Natural and Anthropogenic Influences on the Release of Contaminants to the Subsurface Environment from Waste Source Terms at the INEEL

    Energy Technology Data Exchange (ETDEWEB)

    Paul L. Wichlacz

    2003-09-01

    This source-term summary document is intended to describe the current understanding of contaminant source terms and the conceptual model for potential source-term release to the environment at the Idaho National Engineering and Environmental Laboratory (INEEL), as presented in published INEEL reports. The document presents a generalized conceptual model of the sources of contamination and describes the general categories of source terms, primary waste forms, and factors that affect the release of contaminants from the waste form into the vadose zone and Snake River Plain Aquifer. Where the information has previously been published and is readily available, summaries of the inventory of contaminants are also included. Uncertainties that affect the estimation of the source term release are also discussed where they have been identified by the Source Term Technical Advisory Group. Areas in which additional information are needed (i.e., research needs) are also identified.

  16. Dioxins from medical waste incineration: Normal operation and transient conditions.

    Science.gov (United States)

    Chen, Tong; Zhan, Ming-xiu; Yan, Mi; Fu, Jian-ying; Lu, Sheng-yong; Li, Xiao-dong; Yan, Jian-hua; Buekens, Alfons

    2015-07-01

    Polychlorinated dibenzo-p-dioxins (PCDDs) and polychlorinated dibenzofurans (PCDFs) are key pollutants in waste incineration. At present, incinerator managers and official supervisors focus only on emissions evolving during steady-state operation. Yet, these emissions may considerably be raised during periods of poor combustion, plant shutdown, and especially when starting-up from cold. Until now there were no data on transient emissions from medical (or hospital) waste incineration (MWI). However, MWI is reputed to engender higher emissions than those from municipal solid waste incineration (MSWI). The emission levels in this study recorded for shutdown and start-up, however, were significantly higher: 483 ± 184 ng Nm(-3) (1.47 ± 0.17 ng I-TEQ Nm(-3)) for shutdown and 735 ng Nm(-3) (7.73 ng I-TEQ Nm(-3)) for start-up conditions, respectively. Thus, the average (I-TEQ) concentration during shutdown is 2.6 (3.8) times higher than the average concentration during normal operation, and the average (I-TEQ) concentration during start-up is 4.0 (almost 20) times higher. So monitoring should cover the entire incineration cycle, including start-up, operation and shutdown, rather than optimised operation only. This suggestion is important for medical waste incinerators, as these facilities frequently start up and shut down, because of their small size, or of lacking waste supply. Forthcoming operation should shift towards much longer operating cycles, i.e., a single weekly start-up and shutdown.

  17. Physics and optimization of plasma startup in the RFP

    Science.gov (United States)

    Mao, W.; Chapman, B. E.; Ding, W. X.; Lin, L.; Almagri, A. F.; Anderson, J. K.; Den Hartog, D. J.; Duff, J.; Ko, J.; Kumar, S. T. A.; Morton, L.; Munaretto, S.; Parke, E.; Reusch, J. A.; Sarff, J. S.; Waksman, J.; Brower, D. L.; Liu, W.

    2015-05-01

    In the tokamak and reversed-field pinch (RFP), inductively driven toroidal plasma current provides the confining poloidal magnetic field and ohmic heating power, but the magnitude and/or duration of this current is limited by the available flux swing in the poloidal field transformer. A portion of this flux is consumed during startup as the current is initiated and ramped to its final target value, and considerable effort has been devoted to understanding startup and minimizing the amount of flux consumed. Flux consumption can be reduced during startup in the RFP by increasing the toroidal magnetic field, Bti, applied to initiate the discharge, but the underlying physics is not yet entirely understood. Toward increasing this understanding, we have for the first time in the RFP employed advanced, non-invasive diagnostics on the Madison Symmetric Torus to measure the evolution of current, magnetic field, and kinetic profiles during startup. Flux consumption during startup is dominantly inductive, but we find that the inductive flux consumption drops as Bti increases. The resistive consumption of flux, while relatively small, apparently increases with Bti due to a smaller electron temperature. However, the ion temperature increases with Bti, exceeding the electron temperature and thus reflecting non-collisional heating. Magnetic fluctuations also increase with Bti, corresponding primarily to low-n modes that emerge sequentially as the safety factor profile evolves from tokamak-like to that of the RFP.

  18. Memristor based startup circuit for self biased circuits

    Science.gov (United States)

    Das, Mangal; Singh, Amit Kumar; Rathi, Amit; Singhal, Sonal

    2016-04-01

    This paper presents the design of a Memristor based startup circuit for self biased circuits. Memristor has many advantages over conventional CMOS devices such as low leakage current at nanometer scale, easy to manufacture. In this work the switching characteristics of memristor is utilized. First the theoretical equations describing the switching behavior of memristor are investigated. To prove the switching capability of Memristor, a startup circuit based on memristor is proposed which uses series combination of Memristor and capacitor. Proposed circuit is compared with the previously reported MOSFET based startup circuits. Comparison of different circuits was done to validate the results. Simulation results show that memristor based circuit can attain on (I = 12.94 µA) to off state (I = 1 .2 µA) in 25 ns while the MOSFET based startup circuits take on (I = 14.19 µA) to off state (I = 1.4 µA) in more than 90 ns. The benefit comes in terms of area because the number of components used in the circuit are lesser than the conventional startup circuits.

  19. The Rationality and Irrationality of Financing Green Start-Ups

    Directory of Open Access Journals (Sweden)

    Linda Bergset

    2015-11-01

    Full Text Available Green start-ups contribute towards a transition to a more sustainable economy by developing sustainable and environmentally friendly innovation and bringing it to the market. Due to specific product/service characteristics, entrepreneurial motivation and company strategies that might differ from that of other start-ups, these companies might struggle even more than usual with access to finance in the early stages. This conceptual paper seeks to explain these challenges through the theoretical lenses of entrepreneurial finance and behavioural finance. While entrepreneurial finance theory contributes to a partial understanding of green start-up finance, behavioural finance is able to solve a remaining explanatory deficit produced by entrepreneurial finance theory. Although some behavioural finance theorists are suggesting that the current understanding of economic rationality underlying behavioural finance research is inadequate, most scholars have not yet challenged these assumptions, which constrict a comprehensive and realistic description of the reality of entrepreneurial finance in green start-ups. The aim of the paper is thus, first, to explore the specifics of entrepreneurial finance in green start-ups and, second, to demonstrate the need for a more up-to-date conception of rationality in behavioural finance theory in order to enable realistic empirical research in this field.

  20. U.S. Released a New Strategy for Disposal of Nuclear Waste%美国出台新的核废物处置战略

    Institute of Scientific and Technical Information of China (English)

    卫之奇

    2013-01-01

    In January 2013, the U.S. Department of Energy released the strategy for disposal and management of spent fuel and high-level nuclear waste. This paper mainly investigates and analyzes the strategy’s system design elements and challenges in its implementation process. The strategy is mainly aimed to address the worldwide problem of the HLW disposal, and puts forward a three-phase objective. The critical factors for its implementation include establishment and operation of a consent-based siting process, reform of the funding mechanism, establishment of a new waste management and disposal institutes, and the new legal authorization by the U.S. congress as well. In addition, it is also very important to win the public understanding and support for nuclear waste disposal. This could provide some reference for the ongoing siting activities related in China.%2013年1月,美国能源部发布《乏燃料及高放废物管理的处置战略》。通过对新出台的核废物处置战略的系统设计和组织实施的要素及面临的挑战进行分析,得出如下结论:该战略力图解决高放废物的处置这一世界性课题,并提出了三步走目标,其实施的关键在于同意制选址机制的确立和运行、相关资金机制的改革、建立专门的新的核废物管理和处置机构、以及美国国会给予新的立法授权等。此外,公众的理解和支持也至关重要。美国处置核废物战略对我国开展核废物处置及相关选址工作有一定启迪。

  1. CBs levels in deer tissue samples following an accidental release from a special waste treatment center : 2003 results

    Energy Technology Data Exchange (ETDEWEB)

    Mackenzie, A.; Zhang, W.; Gabos, S.; Schopflocher, D.; Robb, J. [Alberta Health and Wellness, Edmonton, AB (Canada). Health Surveillance; Ikonomou, M. [Inst. of Ocean Sciences, Sidney, BC (Canada)

    2005-07-01

    High levels of dioxins and furans (PCDD/Fs) were observed in deer and mouse tissues examined after an accidental release of PCDD/F contaminants in the Swan Hills area of Alberta. This paper provided details of follow-up sampling conducted to assess changes in CB concentrations of whitetail deer and mule deer in the region. Field collection was carried out in December 2002 and February 2003. Representative muscle, liver and fat samples were taken from each deer. Four aliquots from each sample were collected by carbon-fibre fractionation. All possible 209 CB congeners were measured with minimum isomeric interference. Fractions were analyzed using high resolution gas chromatography (HRGC) and high resolution mass spectrometry (HRMS). Concentrations of identified compounds were calculated using mean relative response factors determined from calibration standard runs. Results showed that 55 of 209 CB congeners were not detected in the fat samples. The mean level of CB homologues in the 2003 study was 39 ng/g for the lipid basis in the muscle, 92 ng/g in the liver, and 20.5 ng/g in the fat. Di-ortho CBs constituted 72 per cent to 74 per cent of CBs for the samples. Concentration levels of SCBs were lower than studies conducted in previous years. It was concluded that overall levels of SCBs and SCBs TEQ in the liver and muscle samples in 2003 significantly declined when compared with levels observed in 1997, 1999, and 2001. 6 refs., 4 tabs.

  2. A new code for modelling the near field diffusion releases from the final disposal of nuclear waste

    Science.gov (United States)

    Vopálka, D.; Vokál, A.

    2003-01-01

    The canisters with spent nuclear fuel produced during the operation of WWER reactors at the Czech power plants are planned, like in other countries, to be disposed of in an underground repository. Canisters will be surrounded by compacted bentonite that will retard the migration of safety-relevant radionuclides into the host rock. A new code that enables the modelling of the critical radionuclides transport from the canister through the bentonite layer in the cylindrical geometry was developed. The code enables to solve the diffusion equation for various types of initial and boundary conditions by means of the finite difference method and to take into account the non-linear shape of the sorption isotherm. A comparison of the code reported here with code PAGODA, which is based on analytical solution of the transport equation, was made for the actinide chain 4N+3 that includes 239Pu. A simple parametric study of the releases of 239Pu, 129I, and 14C into geosphere is discussed.

  3. Potential of Effective micro-organisms and Eisenia fetida in enhancing vermi-degradation and nutrient release of fly ash incorporated into cow dung-paper waste mixture.

    Science.gov (United States)

    Mupambwa, Hupenyu Allan; Ravindran, Balasubramani; Mnkeni, Pearson Nyari Stephano

    2016-02-01

    The interactions between earthworms and microorganisms activity has prompted several researchers to evaluate the potential of artificially inoculating vermicomposts with additional specific microbes, with the intention of enhancing the vermicomposting process. This study evaluated the potential of inoculating fly ash (F)-cow dung-paper waste (CP) mixture (F-CP) with a specialized microbial cocktail called Effective micro-organisms (EM) during vermicomposting using Eisenia fetida earthworms. Inoculation with EM alone did not result in significantly (P>0.05) different changes in C/N ratio and dissolved organic matter (DOC) compared to the control with no EM and E. fetida. A significant interaction between EM and E. fetida presence resulted in greater changes in C/N ratio and DOC, which were not statistically different from the E. fetida alone treatment. It was also noteworthy that the activity of ß-Glucosidase was not influenced by the presence of EM, but was significantly influenced (P=0.0014) by the presence of E. fetida. However, the EM+E. fetida treatment resulted in a rate of weekly Olsen P release of 54.32mgkg(-1) which was 12.3%, 89.2% and 228.0% more that the E. fetida alone, EM alone and control treatments, respectively. Similarly, though higher in the E. fetida plus EM treatment, the phosphate solubilizing bacteria counts were not significantly different (P>0.05) from the E. fetida alone treatment. It is concluded that inoculation of F-CP composts with EM alone may not be beneficial, while combining EM with E. fetida results in faster compost maturity and significantly greater Olsen P release. It would be interesting to evaluate higher optimized rates of EM inoculation and fortifying EM cocktails with phosphate solubilizing bacteria (PSB) on F-CP vermicompost degradation and phosphorus mineralization.

  4. Start-Up Processes’ Efficiency of Turbine Jet Engines

    Directory of Open Access Journals (Sweden)

    Jankowski Antoni

    2016-12-01

    Full Text Available The paper presents diagnoses of example start-up processes of drive units built in military aircraft operated in the Dęblin's “School of Eaglets” during the flight. The significance of this process is very important, especially from the point of view of flight safety, especially as it concerns the training aircraft, on which officer cadets-candidates for pilots are trained. The diagnosis of the start-up process was conducted using data from on-board flight recorders recorded during a flight training, whose aim was an emergency launch of particular drive units, and with the help of the so-called phase mapping of the selected operating parameters of the particular flight drive systems. The standard diagram of typical start-up systems was shown, while presenting their base subassemblies. At the end, the obtained results and the main problems that need intervention were commented, as well as further preventive activities were proposed.

  5. Quel contrôle de gestion pour les startups ?

    OpenAIRE

    Meyssonnier, François

    2015-01-01

    Une étude de huit PME fondées sur la science permet d’identifier les spécificités du contrôle de gestion des startups. Dans les startups émergentes le dirigeant n’utilise que des linéaments de contrôle de gestion essentiellement pour développer son approche cognitive du business model. Dans les startups en croissance le contrôle de gestion a un rôle de garde-fou et les outils de pilotage de la performance sont utilisés essentiellement de façon interactive et pour la prévision. Les principaux ...

  6. Team Heterogeneity in Startups and its Development over Time

    DEFF Research Database (Denmark)

    Kaiser, Ulrich; Müller, Bettina

    We investigate the workforce heterogeneity of startups with respect to education, age and wages. Our explorative study uses data on the population of 1,614 Danish firms founded in 1998. We track these firms until 2001 which enables us to analyze changes in workforce composition over time. Such a ......We investigate the workforce heterogeneity of startups with respect to education, age and wages. Our explorative study uses data on the population of 1,614 Danish firms founded in 1998. We track these firms until 2001 which enables us to analyze changes in workforce composition over time...... as “homophily” (people’s inclination to bound with others with similar characteristics) hence appear to generally overweigh the benefits of heterogeneity (like greater variety in perspectives or more creativity). We also document that workforces become more heterogeneous over time startups add workers...

  7. A Sales Execution Strategy Guide for Technology Startups

    Directory of Open Access Journals (Sweden)

    Ian Gilbert

    2011-10-01

    Full Text Available The majority of startups fail to consider sales execution as part of their overall strategy. This article demonstrates how a sales execution strategy can help a company take a product or service to market more efficiently and effectively by focusing on the customers that are key to generating revenue. Combined with techniques for recruiting effectively and measuring sales outcomes, a sales execution strategy helps technology startups exceed growth aspirations and potentially reduce or even eliminate the requirement for external investment. In this article, we first describe the focus of assistance currently given to startups and the reasons why sales execution strategies are often overlooked. Next, we outline recommendations for developing, implementing, and supporting a sales execution strategy. Finally, we summarize the key points presented in the article.

  8. Optimising Start-Up of a Crankshaft Press Drive

    Directory of Open Access Journals (Sweden)

    E. N. Skladchikov

    2014-01-01

    Full Text Available The purpose of research is to decrease energy consumption as well as acceleration and heat time of the engine of main drive crankshaft press when starting it up. Modern crankshaft press designs include a flywheel connected to the engine by a belt drive. The flywheel performing a process operation spends the reserved kinetic energy. By virtue thereof it should possess the significant moment of inertia. It defines duration of acceleration process. High starting currents of engines lead to their vigorous heating and energy consumption at acceleration.The literature describes the way for eliminating these shortcomings, which is confined to the start-up of the asynchronous engine with a phase rotor when the circuit of each rotor phase includes an additional stepped resistance. However, there are no proved recommendations to specified resistance values and duration of engine acceleration at each step.Research used mathematical modeling and process optimization of three-stage acceleration of engine possessing a flywheel with the following optimization criteria: energy consumption at start-up, an equivalent (heating current of engine, acceleration time. Values of additional resistance and start-up time at each step are chosen to be parameters of optimization.Obtained results show, that optimization of drive start-up allows us to reduce time of acceleration from 27.3s up to 11.24s, energy consumption from 4405930 Joule up to 2538400 Joule, and an equivalent (heating current from 60.34 up to 14.01 А.As a result of research it is found, that a preferable start-up is the press drive start-up in modes with optimum time of flywheel acceleration and an optimum equivalent current, as the most efficient according to all optimization criteria.

  9. Waste disposal package

    Science.gov (United States)

    Smith, M.J.

    1985-06-19

    This is a claim for a waste disposal package including an inner or primary canister for containing hazardous and/or radioactive wastes. The primary canister is encapsulated by an outer or secondary barrier formed of a porous ceramic material to control ingress of water to the canister and the release rate of wastes upon breach on the canister. 4 figs.

  10. Sealed source dismantling hot cell - startup

    Energy Technology Data Exchange (ETDEWEB)

    Dellamano, Jose Claudio; Ferreira, Robson de Jesus, E-mail: jcdellam@ipen.br, E-mail: rojefer@ipen.br [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil). Gerencia de Rejeitos radioativos

    2013-07-01

    Sealed radioactive sources are widely used in many applications of nuclear technology and at the end of the useful life, most sources become radioactive waste. In Brazil, this waste is received by the Institutes of the National Nuclear Energy Commission and kept under centralized storage. The Waste Management Department at the Nuclear and Energy Research Institute is the main storage center, having received around 20,000 disused sources. A hot cell was designed and constructed to manage Co-60 spent sealed sources with activity up to 3.7 10{sup 1}0 Bq and other sources with equivalent activities. In the hot cell the sources are withdraw from their original shielding and transferred to a standard shielding for further disposal off. The original shielding disassembling is made outside the hot cell and after opening, it is transferred inside the hot cell and the sealed source is removed remotely. The source is checked in relation to external contamination and its activity is checked. After this, the source is positioned in the standard shielding located inside an overpack at the bottom of the hot cell. This paper describes some pre-operational tests carried out in it, that include: opening and closing doors and locks, checking of all electrical and pneumatic controls, the original shielding movement inside the hot-cell, dose rate measurements outside the hot-cell, insertion of the sealed sources inside the activity meter chamber, transferring the sealed source to the standard shielding, movement of the overpack with the standard shielding to outside of the hot-cell and plugging of the standard shielding. (author)

  11. Female Hires and the Success of Start-up Firms

    OpenAIRE

    Weber, Andrea Maria; Zulehner, Christine

    2009-01-01

    In this paper we investigate the relationship between females among the first hires of start-up companies and business success. Our results show that firms with female first hires have a higher share of female workers at the end of the first year after entry. Further, we find that firms with female first hires are more successful and stay longer in the market. We conclude that our results support the hypothesis that gender-diversity in leading positions is an advantage for start-up firms.

  12. Team Heterogeneity in Startups and its Development over Time

    DEFF Research Database (Denmark)

    Kaiser, Ulrich; Müller, Bettina

    We investigate the workforce heterogeneity of startups with respect to education, age and wages. Our explorative study uses data on the population of 1,614 Danish firms founded in 1998. We track these firms until 2001 which enables us to analyze changes in workforce composition over time...... as “homophily” (people’s inclination to bound with others with similar characteristics) hence appear to generally overweigh the benefits of heterogeneity (like greater variety in perspectives or more creativity). We also document that workforces become more heterogeneous over time startups add workers...

  13. Improvement of operational efficiency based on fast startup plant concepts

    Energy Technology Data Exchange (ETDEWEB)

    Grumann, Ulrich; Kurz, Harald; Meinecke, Gero; Pickard, Andreas

    2010-09-15

    The power generation sector is currently confronted with new challenges relating to the conservation of dwindling fuel reserves. At the same time we must reduce CO2 emissions in order to counteract global warming. This paper shows that power plant operation, which employs shutdowns during periods of low load demand coupled with the optimization of startup procedures are a key to reducing CO2 emissions and to conserving resources. The startup technology developed by Siemens also offers grid support in the event of naturally occurring failures of renewable energy sources. Additionally, plant profitability is improved due to the resulting savings in fuel.

  14. Start-up business plan: organic food restaurant in Bilbao

    OpenAIRE

    Sharafutdinova, Alisa

    2016-01-01

    My thesis is a start-up business plan for a restaurant in Bilbao, Spain. This product-oriented thesis is a part of the Hospitality Management program of Haaga-Helia UAS. The purpose of this work is to build a theoretical framework about successful business plan writing and follow it up by writing a start-up business plan according to the studied theory. A business plan is a first important step for starting a business and the practice of writing it will be beneficial while helping me to ...

  15. Financement et gouvernance des start-ups en equitycrowdfunding

    OpenAIRE

    2016-01-01

    Par rapport aux modes de financement traditionnels, l’equitycrowdfunding (ECF) introduit deux nouveaux acteurs : la plateforme et la foule. Cet article étudie leurs rôles et leurs spécificités dans le processus de financement et dans le design de la gouvernance de la start-up. Ce nouveau système est totalement ouvert, composé d’un très grand nombre de participants hétérogènes qui apportent des ressources financières mais aussi et surtout un retour à la start-up sur leur perception du projet. ...

  16. Start-up business plan: organic food restaurant in Bilbao

    OpenAIRE

    Sharafutdinova, Alisa

    2016-01-01

    My thesis is a start-up business plan for a restaurant in Bilbao, Spain. This product-oriented thesis is a part of the Hospitality Management program of Haaga-Helia UAS. The purpose of this work is to build a theoretical framework about successful business plan writing and follow it up by writing a start-up business plan according to the studied theory. A business plan is a first important step for starting a business and the practice of writing it will be beneficial while helping me to ...

  17. Transient CFD simulation of a Francis turbine startup

    Science.gov (United States)

    Nicolle, J.; Morissette, J. F.; Giroux, A. M.

    2012-11-01

    To assess the life expectancy of hydraulic turbines, it is essential to obtain the loading on the blades, especially during transient operations known to be the most damaging. This paper presents a simplified CFD setup to model the startup phase of a Francis turbine while it goes from rest to speed no-load condition. The fluid domain included one distributor sector coupled with one runner passage. The guide vane motion and change in the angular velocity were included in a commercial code with user functions. Comparisons between numerical results and measurements acquired on a full-size turbine showed that most of the flow physics occurring during startup were captured.

  18. Order of the 10 january 2003 authorizing the national agency for the radioactive wastes management to follow the gaseous and liquid effluents release for the exploitation of the radioactive wastes storage center of the Manche; Arrete du 10 janvier 2003 autorisant l'Agence nationale pour la gestion des dechets radioactifs a poursuivre les rejets d'effluents gazeux et liquides pour l'exploitation du centre de stockage de dechets radioactifs de la Manche

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2003-01-01

    This document, took out from the Official Journal, is the law text relative to the order of the 10 january 2003 authorizing the national agency for the radioactive wastes management to follow the gaseous and liquid effluents release for the exploitation of the radioactive wastes storage center of the Manche. (A.L.B.)

  19. The emergence of the lean global start-up as a new type of firm

    OpenAIRE

    Rasmussen, Erik Stavnsager; Tanev, Stoyan

    2015-01-01

    The present paper contributes to the interplay between international entrepreneurship, innovation networks and early internationalization research emphasizing the need to conceptualize and introduce a new type of firm – the Lean Global Start-up. It discussed two different paths in linking the lean start-up and born global internationalization strategies. The first path refers to generic lean start-ups that have undertaken a rapid internationalization strategy (Lean-to-Global Start-ups). The s...

  20. Start-up success of freelancers New microeconometric evidence from the German Socio-Economic Panel

    OpenAIRE

    Merz, Joachim; Paic, Peter

    2006-01-01

    If certain start-up characteristics will indicate a business success, knowing such characteristics could generate more successful start-ups and more efficient start-up counseling. Our study will contribut e to this by quantifying individual success determinants of freelance start-ups. The data base for the microeconometric analyses of the survival of the first three years is a revised German Socio-Economic Panel (SOEP) for 1992 until 2002, which allows to incorporate institutional, personal a...

  1. Dynamics and Control During Start-Up of Energy Integrated Distillation Column

    DEFF Research Database (Denmark)

    a systematic procedure for development of plant start-up sequences. The basis for the start-up procedure development is available qualitative process knowledge. Application of the start-up sequence generation procedure is demonstrated upon an energy integrated distillation plant. This plant illustrates some...

  2. Dynamics and Control During Start-up of Energy Integrated Distillation Column

    DEFF Research Database (Denmark)

    Eden, Mario Richard; Koggersbøl, Arne; Hallager, L.;

    2000-01-01

    of a generated start-up sequence illustrates that safe and reliable start- ups are ensured. The main conclusions of the paper are that it is indeed possible to generate safe and reliable start-up sequences using qualitative process knowledge. However the selection of an optimal start-up sequence is not possible...

  3. The Performance Of Team Start-Ups In The First Phases Of The Life Course

    NARCIS (Netherlands)

    F.C. Stam (Erik); V. Schutjens (Veronique)

    2004-01-01

    textabstractThis article describes the benefits and pitfalls of starting a firm with an entrepreneurial team, drawing on a longitudinal empirical analysis of the life course of 90 team start-ups and 1196 solo start-ups in the Netherlands. In the first three years of their existence, team start-ups p

  4. Our start-up could never have been successful

    NARCIS (Netherlands)

    Bonger, S.

    2014-01-01

    In July 2013, TU Delft alumnus Jan van Kranendonk and his business partner Thomas de Leeuw decided to discontinue their start-up company Sunuru. The reason was that customers were not interested in their ingenious solar project. Van Kranendonk spoke about his failure during the Failcon event in Amst

  5. CERN confident of LHC start-up in 2007

    CERN Multimedia

    Vanden Broeck, Renilde

    2007-01-01

    "Delegates attending the 140th meeting of CERN Council today heard a confident report from the Laboratory about the scheduled start-up of the world's highest energy particle accelerator, the Large Hadron Collier (LHC) in 2007. (1/2 page)

  6. CERN confident of LHC start-up in 2007

    CERN Multimedia

    2006-01-01

    "Delegates attending the 140th meeting of CERN Council today heard a confident report from the Laboratory about the scheduled start-up of the world's highest energy particle accelerator, the Large Hadron Collider (LHC) in 2007." (1/2 page)

  7. Start-Up Rhetoric in Eight Speeches of Barack Obama

    Science.gov (United States)

    O'Connell, Daniel C.; Kowal, Sabine; Sabin, Edward J.; Lamia, John F.; Dannevik, Margaret

    2010-01-01

    Our purpose in the following was to investigate the start-up rhetoric employed by U.S. President Barack Obama in his speeches. The initial 5 min from eight of his speeches from May to September of 2009 were selected for their variety of setting, audience, theme, and purpose. It was generally hypothesized that Barack Obama, widely recognized for…

  8. Characteristics Contributing to High-Technology Start-Up Success

    DEFF Research Database (Denmark)

    Goslin, L.; Brown, W.; Palm, T.

    1993-01-01

    that the professional venture-capital-funded start-up firm will generally reflect the practices of perceptive management regarding: style, team approach, structure of the firm, market definition, culture, vision, and a formal strategy. Nevertheless, there are some questions about differences those characteristics...

  9. How do new product development startups handle missing expertise?

    NARCIS (Netherlands)

    Eris, O.; van den Eijnden, W.; Roling, M.

    2014-01-01

    This paper presents a framework for how new product development focused startup firms (NPDSF) handle missing expertise. The dimensions of the framework are: strategies for handling missing expertise, channels used to acquire missing expertise, and a priori awareness, timing and nature of missing exp

  10. Evaluating effectiveness of project start-ups: an exploratory study

    NARCIS (Netherlands)

    Halman, J.I.M.; Burger, G.T.N.

    2002-01-01

    In this paper an exploratory study is reported about the effectiveness of project start-up (PSU) practices within a world-scale operating, high technology innovating and manufacturing company. The emphasis is on the focal position of both project owner and project manager. To uncover potential diffe

  11. Social Capital in Knowledge Intensive Start-Ups

    DEFF Research Database (Denmark)

    Neergaard, Helle; Madsen, Henning

    This paper addresses social capital in biotechnology, medico and information communication start-ups using both quantitative and qualitative data. It shows that founding teams are primarily composed of 'trusted alters' and that networking patterns are highly influenced by the entrepreneur...

  12. Characteristics Contributing to High-Technology Start-Up Success

    DEFF Research Database (Denmark)

    Goslin, L.; Brown, W.; Palm, T.

    1993-01-01

    The factors contributing to the success of high technology start-up firms have received much discussion in current business literature. The discussion of the characteristics of success has been based on increasing substantiation by empirical research. The available information suggests that the p...

  13. Solenoid-free plasma start-up in spherical tokamaks

    Science.gov (United States)

    Raman, R.; Shevchenko, V. F.

    2014-10-01

    The central solenoid is an intrinsic part of all present-day tokamaks and most spherical tokamaks. The spherical torus (ST) confinement concept is projected to operate at high toroidal beta and at a high fraction of the non-inductive bootstrap current as required for an efficient reactor system. The use of a conventional solenoid in a ST-based fusion nuclear facility is generally believed to not be a possibility. Solenoid-free plasma start-up is therefore an area of extensive worldwide research activity. Solenoid-free plasma start-up is also relevant to steady-state tokamak operation, as the central transformer coil of a conventional aspect ratio tokamak reactor would be located in a high radiation environment but would be needed only during the initial discharge initiation and current ramp-up phases. Solenoid-free operation also provides greater flexibility in the selection of the aspect ratio and simplifies the reactor design. Plasma start-up methods based on induction from external poloidal field coils, helicity injection and radio frequency current drive have all made substantial progress towards meeting this important need for the ST. Some of these systems will now undergo the final stages of test in a new generation of large STs, which are scheduled to begin operations during the next two years. This paper reviews research to date on methods for inducing the initial start-up current in STs without reliance on the conventional central solenoid.

  14. University Knowledge Spillovers & Regional Start-up Rates

    DEFF Research Database (Denmark)

    Hellerstedt, Karin; Wennberg, Karl; Frederiksen, Lars

    2014-01-01

    This chapter investigates how regional start-up rates in the knowledge-intensive services and high-tech industries are influenced by knowledge spillovers from both universities and firm-based R&D activities. Integrating insights from economic geography and organizational ecology into the literatu...

  15. Start-up of a drinking water biofilter

    DEFF Research Database (Denmark)

    Ramsay, Loren; Søborg, Ditte; Breda, Inês Lousinha Ribeiro

    When virgin filter media is placed in drinking water biofilters, a start-up period of some months typically ensues. During this period, the necessary inorganic coating and bacterial community are established on the filter medium, after which the treated water complies with drinking water criteria...

  16. Trends in the Crowdfunding of Educational Technology Startups

    Science.gov (United States)

    Antonenko, Pavlo D.; Lee, Brenda R.; Kleinheksel, A. J.

    2014-01-01

    This article presents an analysis of active crowdfunding campaigns posted on ten crowdfunding platforms in May 2013 to provide a glimpse of the recent trends in the crowdfunding of educational technology startups. We describe the characteristics of the most successful crowdfunding campaigns in educational technology and identify the most popular…

  17. Evaluating effectiveness of project start-ups: an exploratory study

    NARCIS (Netherlands)

    Halman, Johannes I.M.; Burger, G.T.N.

    In this paper an exploratory study is reported about the effectiveness of project start-up (PSU) practices within a world-scale operating, high technology innovating and manufacturing company. The emphasis is on the focal position of both project owner and project manager. To uncover potential

  18. Success of Breast Cancer Startup Challenge Inspires Second Challenge | Poster

    Science.gov (United States)

    By Thomas Stackhouse, Joseph Conrad, and Michele Newton, Contributing Writers, and Rosemarie Truman, Guest Writer Sixty-one teams have been accepted into, and are now competing in, the Neuro Startup Challenge, a new collaboration established by the National Institutes of Health (NIH) with The Center for Advancing Innovation (CAI) and Heritage Provider Network, Inc.

  19. Acetate enhances startup of a H2-producing microbial biocathode

    NARCIS (Netherlands)

    Jeremiasse, A.W.; Hamelers, H.V.M.; Croese, E.; Buisman, C.J.N.

    2012-01-01

    H2 can be produced from organic matter with a microbial electrolysis cell (MEC). To decrease MEC capital costs, a cathode is needed that is made of low-cost material and produces H2 at high rate. A microbial biocathode is a low-cost candidate, but suffers from a long startup and a low H2 production

  20. Social Capital in Knowledge Intensive Start-Ups

    DEFF Research Database (Denmark)

    Neergaard, Helle; Madsen, Henning

    This paper addresses social capital in biotechnology, medico and information communication start-ups using both quantitative and qualitative data. It shows that founding teams are primarily composed of 'trusted alters' and that networking patterns are highly influenced by the entrepreneur...

  1. Accelerating Research Innovation by Adopting the Lean Startup Paradigm

    Directory of Open Access Journals (Sweden)

    Kaisa Still

    2017-05-01

    Full Text Available Converting scientific expertise into marketable products and services is playing an increasingly important role in the launching of new ventures, the growth of existing firms, and the creation of new jobs. In this article, we explore how the lean startup paradigm, which validates the market for a product with a business model that can sustain subsequent scaling, has led to a new process model to accelerate innovation. We then apply this paradigm to the context of research at universities and other research organizations. The article is based on the assumption that the organizational context matters, and it shows how a deeper understanding of the research context could enable an acceleration of the innovation process. We complement theoretical examples with a case example from VTT Technical Research Institute of Finland. Our findings show that many of the concepts from early-acceleration phases – and the lean startup paradigm – can also be relevant in innovation discussions within the research context. However, the phase of value-proposition discovery is less adequately addressed, and that of growth discovery, with its emphasis on building on a scalable, sustainable business does not seem to be addressed with the presented innovation approaches from the research context. Hence, the entrepreneurial activities at the research context differ from those in startups and internal startups in established organizations.

  2. Dampak Mentoring Pada Keberhasilan Start-Up Business: Studi Kasus Pada Start-Up Business di Indonesia [Mentoring the Impact of Success of a Start-Up Business: A Case Study of a Start-Up Business in Indonesia

    Directory of Open Access Journals (Sweden)

    Christina Yanita Setyawati

    2016-10-01

    Full Text Available Entrepreneurship is a highly developed science today, as well as in the world of education in Indonesia. Teaching entrepreneurship at the university level, especially at some universities in Surabaya, the second largest city in Indonesia, shows the positive impact that there were 74.03% of start-up businesses that survived and thrived in 2014. Based on the previous observation, some business start-ups are accompanied by a mentor. Mentoring is a process of forming and maintaining lasting relationships that develop intensively among seniors with juniors. The mentoring function includes career and psychosocial functions. The main purpose of this research is to study the relationship between mentoring and the success of a start-up business. This study is a quantitative descriptive study using a random sampling method to obtain 100 samples. The tool used to collect data was a questionnaire. The methodology used to analyze the quantitative description to test the hypothesis. The results of this study indicate that mentoring influences the success of a start-up business that was owned by university students in Surabaya, Indonesia by 32% and 78% was influenced by other variables.

  3. Beta: An Experiment in Funded Undergraduate Start-Up

    Science.gov (United States)

    Jones, Paul; Forbes-Simpson, Kellie; Maas, Gideon; Newbery, Robert

    2015-01-01

    This paper reports on an evaluation of a funded undergraduate project designed to enable student business start-up. The programme, entitled "Beta", provides undergraduate students with £1,500 of seed-corn funding. The key objective of the project is for the participants to exit it with a viable and legal business entity through which…

  4. PLASMA GASIFICATION OF WASTE PLASTICS

    Directory of Open Access Journals (Sweden)

    Tadeusz Mączka

    2013-01-01

    Full Text Available The article presents the process of obtaining liquid fuels and fuel gas in the process of plasma processing of organic materials, including waste plastics. The concept of plasma pyrolysis of plastics was presented and on its basis a prototype installation was developed. The article describes a general rule of operating the installation and its elements in the process and basic operation parameters determined during its start-up. Initial results of processing plastics and the directions further investigations are also discussed. The effect of the research is to be the design of effective technology of obtaining fuels from gasification/pyrolysis of organic waste and biomass.

  5. Assessing the subsequent effect of nitrogen released from tobacco-waste on maize crop using a ¹⁵N isotope technique.

    Science.gov (United States)

    Karaman, M Rüştü; Brohi, A Reşit

    2013-06-01

    The investigation of the residual effect of nitrogen (N) released from tobacco-waste (TW) using isotope techniques will provide valuable data for sustainable organic farming. For this aim, a pot experiment was conducted using the (15)N isotope technique. The experiment was based on a completely randomised design with four replications and was conducted on a calcareous ustochrepts soil. TW at levels of 0, 10, 20, 30 and 40 t ha(-1) and N fertiliser as (NH₄)₂SO₂ at levels of 0, 20, 40, 60 and 80 kg N ha(-1) were used for the Bezostaja-1 wheat variety. Concerning mineral N fertilisation with 20 and 80 kg N ha(-1), additional treatments with (15)N-labelled (NH₄)₂SO₂ (10 at.% exc.) have been applied. Following harvesting wheat plants, the Pioneer 3377 maize variety was used to see the residual effect of TW. After harvesting, dry matter yields were recorded and total N concentrations were determined. (15)N determinations and calculations were also made for (15)N treatments separately. TW had a significant residual effect on the growth of corn plant under the pot condition. Increasing rates of TW significantly increased the dry matter yield of corn plant following wheat from 3.31 t ha(-1) (at control) to 7.89 t ha(-1) (at the TW treatment of 40 t ha(-1)). The (15)N values derived from the (15)N fertiliser decreased with increasing TW application. The average values of N derived from N fertiliser (Ndff) varied from 2.14 to 3.09% at the rates of 20 and 80 kg N ha(-1), respectively. However, N derived from TW (Ndftw) significantly increased from 16.93 to 24.59% (at 20 kg N ha(-1)), and it also increased from 23.06 to 28.15% (at 80 kg N ha(-1)) with increasing TW applications from 20 to 40 t ha(-1), respectively.

  6. Using genetic algorithm to learn neural network identifier for modeling gyro startup drift rate

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    Studies the modeling of gyro startup drift rate from acquired experimental gyro startup drift rate data and the nonlinear dynamic models of gyro startup drift rate related temperature established by time-delay neural network which enables the gyro temperature drift rate to be compensated in the process of startup and the gyro instant startup to be implemented. And introduces an improved genetic algorithm to learn the weights of neural network identifier to avoid stacking into the local minimal value and achieve rapid convergence.

  7. Viscoelasticity, nonlinear shear start-up, and relaxation of entangled star polymers

    KAUST Repository

    Snijkers, Frank

    2013-07-23

    We report on a detailed rheological investigation of well-defined symmetric entangled polymer stars of low functionality with varying number of arms, molar mass of the arms, and solvent content. Emphasis is placed on the response of the stars in simple shear, during start-up, and for relaxation upon flow cessation. To reduce experimental artifacts associated with edge fracture (primarily) and wall slip, we employ a homemade cone-partitioned plate fixture which was successfully implemented in recent studies. Reliable data for these highly entangled stars could be obtained for Weissenberg numbers below 300. The appearance of a stress overshoot during start-up with a corresponding strain approaching a value of 2 suggests that in the investigated shear regime the stars orient but do not stretch. This is corroborated by the fact that the empirical Cox-Merx rule appears to be validated, within experimental error. On the other hand, the (shear) rate dependent steady shear viscosity data exhibit a slope smaller than the convective constraint release slope of -1 (for linear polymers) for the investigated range of rates. The broadness of the stress overshoot reflects the broad linear relaxation spectrum of the stars. The initial stress relaxation rate, reflecting the initial loss of entanglements due to the action of convective constraint release in steady shear flow, increases with Weissenberg number. More importantly, when compared against the relevant rates for comb polymers with relatively short arms, the latter are slower at larger Weissenberg numbers. At long times, the relaxation data are consistent with the linear viscoelastic data on these systems. © 2013 American Chemical Society.

  8. The emergence of the lean global start-up as a new type of firm

    DEFF Research Database (Denmark)

    Rasmussen, Erik Stavnsager; Tanev, Stoyan

    2015-01-01

    The present paper contributes to the interplay between international entrepreneurship, innovation networks and early internationalization research emphasizing the need to conceptualize and introduce a new type of firm – the Lean Global Start-up. It discussed two different paths in linking the lean...... and adopted the lean start-up approach by seamlessly synergizing their global and lean product development activities. The paper emphasizes several aspects that could be used as part of the theoretical foundation for conceptualizing lean global start-ups as a special new type of firm: the emergent nature...... start-up and born global internationalization strategies. The first path refers to generic lean start-ups that have undertaken a rapid internationalization strategy (Lean-to-Global Start-ups). The second path refers to start-ups that have started operating on global scale since their inception...

  9. Webometrics for an Open Access Start-Up Journal (Editorial

    Directory of Open Access Journals (Sweden)

    Ulf-Dietrich Reips

    2009-01-01

    Full Text Available Before you stands the fourth issue of the International Journal of Internet Science. It will be the last one that is the only issue in its volume, because an increasing rate of manuscript submissions of high quality to this start-up journal forces us to jump to two issues next year. From citation analysis to webometrics Our citation analysis in the previous issue (Reips & Matzat, 2008 revealed a surprisingly high journal impact for the International Journal of Internet Science. To publish very few high quality articles has already catapulted this start-up journal beyond many of the long-standing journals in the field. Looking up "International Journal of Internet Science" in Google Scholar now returns 90 instead of 50 references (December 15, 2009, compared to the same day in 2008. Among them are many new citations relevant to the journal's impact factor.

  10. Lean Startup and Lean Canvas Using for Innovative Product Development

    Directory of Open Access Journals (Sweden)

    Alena Buchalcevová

    2016-06-01

    Full Text Available Recently, new approaches to product development have emerged that focus on idea generation techniques and customer itself. One of them is the Lean Startup method that is described in this article along with the Lean Canvas method. The main goal of the article is to demonstrate the application of both methods to an innovative product development focused on providing interactive trips for families with children. The development of the product during individual phases is described and application of the Lean Startup and Lean Canvas principles is demonstrated. Finally, benefits of both methods contributing to the product success are discussed. Similar case studies start emerging worldwide, however in the Czech context are quite rare.

  11. Research Strategies in Science-based Start-ups

    DEFF Research Database (Denmark)

    Valentin, Finn; Dahlgren, Johan Henrich; Lund Jensen, Rasmus

    Although biotech start-ups fail or succeed based on their research few attempts have been made to examine if and how they strategize in this core of their activity. Popular views on Dedicated Biotech Firms (DBFs) see the inherent uncertainty of research as defying notions of strategizing, directing...... instead the attention to the quality of their science, or the roles of boards, management, and collaborative networks etc. Using a unique comprehensive dataset on Danish and Swedish biotech start-ups in drug discovery this paper analyzes their research strategies. Adopting a Simonean point of departure we...... developed as congruent responses to problem architectures; 3) Testing and confirming that financial valuation of firms is driven by achievements conforming to requisite research strategies. These strategies, in turn, require careful combination of multiple dimensions of research.Findings demonstrate...

  12. Watts Bar Unit 2 Startup Results with VERA

    Energy Technology Data Exchange (ETDEWEB)

    Godfrey, Andrew T. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Collins, Benjamin S. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Gentry, Cole A. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Stimpson, Shane G. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Ritchie, John A. [Tennessee Valley Authority (TVA), Knoxville, TN (United States)

    2017-03-01

    CASL members TVA, Westinghouse, and Oak Ridge National Laboratory have successfully completed a detailed simulation of the initial startup of Watts Bar Nuclear Unit 2 (WBN2) using the advanced reactor simulation tools known as VERA. WBN2 is the first commercial power reactor to join the nation’s electrical grid in over two decades, and the modern core design and availability of data make it an excellent benchmark for CASL. Calculations were performed three months prior to the startup, and in the first blind application of VERA to a new reactor, predicted criticality and physics parameters very close to those later measured by TVA. Subsequent calculations with the latest version of VERA and using exact measurement conditions improved the results even further.

  13. Sustainability Strategies for Regional Health Information Organization Startups

    DEFF Research Database (Denmark)

    Winkler, Till J.; Ozturk, Pinar; Brown, Carol V.

    2016-01-01

    initiatives by states and regional health information organizations (HIOs). Given the high failure rates of regional U.S. HIOs in the past, our primary objective is to identify the key characteristics of HIO startups that became operational and demonstrated sustainability with non-renewable SHIECAP funding...... HIOs that became operational during the SHIECAP grant period faced similar startup challenges, the two HIOs that demonstrated sustainability pursued distinct technology and sustainability strategies to develop HIE capabilities to fit their very different regional needs: an HIE capability to improve...... the population health of an underserved urban population, and an HIE capability to enable the transition to a healthcare landscape that rewards care coordination across suburban hospitals and physician practices. Conclusions: We propose two models of technology and sustainability strategies for developing bottom...

  14. Intellectual property in consumer electronics, software and technology startups

    CERN Document Server

    Halt, Jr , Gerald B; Stiles, Amber R; Fesnak, Robert

    2014-01-01

    This book provides a comprehensive guide to procuring, utilizing and monetizing intellectual property rights, tailored for readers in the high-tech consumer electronics and software industries, as well as technology startups.  Numerous, real examples, case studies and scenarios are incorporated throughout the book to illustrate the topics discussed.  Readers will learn what to consider throughout the various creative phases of a product’s lifespan from initial research and development initiatives through post-production.  Readers will gain an understanding of the intellectual property protections afforded to U.S. corporations, methods to pro-actively reduce potential problems, and guidelines for future considerations to reduce legal spending, prevent IP theft, and allow for greater profitability from corporate innovation and inventiveness. • Offers a comprehensive guide to intellectual property for readers in high-tech consumer electronics, software and technology startups; • Uses real case studies...

  15. Our start-up could never have been successful

    OpenAIRE

    Bonger, S.

    2014-01-01

    In July 2013, TU Delft alumnus Jan van Kranendonk and his business partner Thomas de Leeuw decided to discontinue their start-up company Sunuru. The reason was that customers were not interested in their ingenious solar project. Van Kranendonk spoke about his failure during the Failcon event in Amsterdam, which is modelled after similar events in Silicon Valley. ‘Having your own company looks good on your CV.’

  16. Research Strategies in Science-based Start-ups

    DEFF Research Database (Denmark)

    Valentin, Finn; Dahlgren, Johan Henrich; Lund Jensen, Rasmus

    Although biotech start-ups fail or succeed based on their research few attempts have been made to examine if and how they strategize in this core of their activity. Popular views on Dedicated Biotech Firms (DBFs) see the inherent uncertainty of research as defying notions of strategizing, directi...... is needed along these lines, these findings offer new implications for the understanding, management, and financing of these firms.JEL Codes: L25, L65, O32...

  17. ECommerce Strategy for Footwear Manufacturing Start-up

    OpenAIRE

    Kuzmanovic, Slobodan

    2010-01-01

    This paper defines and analyzes an eCommerce strategy for a footwear manufacturing start-up firm and assesses the financial impact this eCommerce strategy has in supporting the firm’s business model. The market analysis of the importance of eCommerce determined the online channel’s market share and influence on consumer purchasing decisions, while the industry analysis examined the competitive landscape and industry forces as drivers of forward integration from manufacturing to wholesale and ...

  18. A Start-Up Produces Infomercials for the Internet

    Institute of Scientific and Technical Information of China (English)

    2011-01-01

    @@ The one thing online shopping is missing, says Sukhinder Singh Cassidy, a former Google executive, is infomercials. Ms.Singh Cassidy introduced her new shopping start-up, Joyus.It is an e-commerce site that produces videos to sell products, like a Web version of the Home Shopping Network. "If you think about the ways to sell online, video is underutilized," she said."It's a new way for brands to merchandise their product."

  19. Developing a business plan for a startup e-business

    OpenAIRE

    Vu, Khanh

    2013-01-01

    The purpose of this thesis is to develop an initial business plan for a startup fashion company that operates on the Internet in the Vietnamese market. To reach the target objective, the thesis first examines e-business from a theoretical perspective and considers its advantages and disadvantages. Secondly, the macro environment of the proposed business is analyzed, namely the country of Vietnam and its e-commerce environment. Finally, the outcome of the thesis is presented in the form of a b...

  20. Start-Up of the Colorectal Cancer Screening Demonstration Program

    Directory of Open Access Journals (Sweden)

    Amy DeGroff, MPH

    2008-04-01

    Full Text Available IntroductionIn 2005, the Centers for Disease Control and Prevention funded five sites to implement the Colorectal Cancer Screening Demonstration Program (CRCSDP. An evaluation is being conducted that includes a multiple case study. Case study results for the start-up period, the time between initial funding and screening initiation, provide details about the program models and start-up process and reveal important lessons learned.MethodsThe multiple case study includes all five CRCSDP sites, each representing a unique case. Data were collected from August 2005 through September 2006 from documents, observations, and more than 70 interviews with program staff and stakeholders.ResultsSites differed by geographic service area, screening modality selected, and service delivery structure. Program models were influenced by two factors: preexisting infrastructure and the need to adapt programs to fit local service delivery structures. Several sites modeled program components after their National Breast and Cervical Cancer Early Detection Program. Medical advisory boards convened by all sites provided clinical support for developing program policies and quality assurance plans. Partnerships with comprehensive cancer control programs facilitated access to financial and in-kind resources.ConclusionThe program models developed by the CRCSDP sites offer a range of prototypes. Case study results suggest benefits in employing a multidisciplinary staff team, assembling a medical advisory board, collaborating with local partners, using preexisting resources, designing programs that are easily incorporated into existing service delivery systems, and planning for adequate start-up time.

  1. Patent Value: A Business Perspective for Technology Startups

    Directory of Open Access Journals (Sweden)

    Angela de Wilton

    2011-12-01

    Full Text Available In the last year, news headlines have highlighted record patent infringement settlements, multibillion dollar auctions of large corporate patent portfolios, and ongoing patent battles between key technology industry players. Despite this acknowledgment of the significant value of patents for large corporations, many small technology companies are understandably more focused on the near-term costs of obtaining a patent rather than future value. Costs may seem prohibitive to an early stage technology startup. Some software startups question whether patents are relevant to their business. In practice, effective intellectual property (IP strategy and management is dependent on many factors, such as technology or industry sector, size and maturity of the business, technology lifecycle, and the business and market environment. IP strategy must be aligned to business strategy from the outset. By considering IP in the broader context of the overall business plan and the competitive environment, opportunities for generating increased return on R&D investment and added business value through patents or other forms of IP can be recognized early on. This approach ensures that a decision about whether or not to patent is driven by business reasons rather than budget constraints. This article examines the costs and benefits of patents from the perspective of early-stage technology startups and growing businesses, and it provides some general guidance on best practices for developing an IP and patent activity plan and for building a patent portfolio that appropriately supports business objectives.

  2. Feasibility study of ECRH in NSTX-U startup plasma

    Science.gov (United States)

    Lopez, N. A.; Poli, F.; Taylor, G.; Harvey, R.; Petrov, Yu.

    2016-10-01

    A key mission goal of the National Spherical Torus eXperiment Upgrade (NSTX-U) is the demonstration of fully non-inductive startup and operation. In part to accomplish this, a 1MW, 28 GHz ECRH system is presently being developed for implementation on NSTX-U in 2018. Like most spherical tokamaks, NSTX-U operates in the overdense regime (fpe>fce) , which limits traditional ECRH to the early startup phase. An extensive modelling effort of the propagation and absorption of EC waves in the evolving plasma is thus required to define the most effective window of operation, and to optimize the launcher geometry for maximal heating and for current drive during this window. In fact, the ECRH system will play an important role in preparing a target plasma for subsequent injection of IC waves and NBI. Here we assess the feasibility of O1-mode ECRH in NSTX-U startup plasma at full field of 1T through time-dependent simulations performed with the transport solver TRANSP. Linear ray-tracing calculations conducted by GENRAY are coupled into the TRANSP framework, allowing the plasma equilibrium and the temperature profiles to evolve self-consistently in response to the injected microwave power. Furthermore, we investigate additional possibilities of heating and current drive made available through coupling the injected O-mode power to the electrostatic EBW via the slow X-mode as an intermediary.

  3. Long Pulse EBW Start-up Experiments in MAST

    Directory of Open Access Journals (Sweden)

    Shevchenko V.F.

    2015-01-01

    Full Text Available Start-up technique reported here relies on a double mode conversion (MC for electron Bernstein wave (EBW excitation. It consists of MC of the ordinary (O mode, entering the plasma from the low field side of the tokamak, into the extraordinary (X mode at a mirror-polarizer located at the high field side. The X mode propagates back to the plasma, passes through electron cyclotron resonance (ECR and experiences a subsequent X to EBW MC near the upper hybrid resonance (UHR. Finally the excited EBW mode is totally absorbed at the Doppler shifted ECR. The absorption of EBW remains high even in cold rarefied plasmas. Furthermore, EBW can generate significant plasma current giving the prospect of a fully solenoid-free plasma start-up. First experiments using this scheme were carried out on MAST [1]. Plasma currents up to 33 kA have been achieved using 28 GHz 100kW 90ms RF pulses. Recently experimental results were extended to longer RF pulses showing further increase of plasma currents generated by RF power alone. A record current of 73kA has been achieved with 450ms RF pulse of similar power. The current drive enhancement was mainly achieved due to RF pulse extension and further optimisation of the start-up scenario.

  4. Market Channels of Technology Startups that Internationalize Rapidly from Inception

    Directory of Open Access Journals (Sweden)

    Simar Yoos

    2012-10-01

    Full Text Available The study of technology startups that internationalize rapidly from inception has increased in recent years. However, little is known about their channels to market. This article addresses a gap in the "born global" literature by examining the channels used by six startups that internationalized rapidly from inception as well as the programs they used to support their channel partners and customers. The six startups examined combined the use of the Internet with: i a relationship with a multi-national, ii distributors, iii re-sellers, or iv a direct sales force. They also delivered programs to support partners and customers that focused on communications, alliance and network development, education, marketing and promotion, and financial incentives. This article informs entrepreneurs who need to design go-to-market channels to exploit global opportunities about decisions made by other entrepreneurs who launched born-global companies. Normative rules and practitioner-oriented approaches are needed to help entrepreneurs explain and apply the results presented in this article.

  5. Calculation of the inventory and near-field release rates of radioactivity from neutron-activated metal parts discharged from the high flux isotope reactor and emplaced in solid waste storage area 6 at Oak Ridge National Laboratory

    Energy Technology Data Exchange (ETDEWEB)

    Kelmers, A.D.; Hightower, J.R.

    1987-05-01

    Emplacement of contaminated reactor components involves disposal in lined and unlined auger holes in soil above the water table. The radionuclide inventory of disposed components was calculated. Information on the composition and weight of the components, as well as reasonable assumptions for the neutron flux fueling use, the time of neutron exposure, and radioactive decay after discharge, were employed in the inventory calculation. Near-field release rates of /sup 152/Eu, /sup 154/Eu, and /sup 155/Eu from control plates and cylinders were calculated for 50 years after emplacement. Release rates of the europium isotopes were uncertain. Two release-rate-limiting models were considered and a range of reasonable values were assumed for the time-to-failure of the auger-hole linear and aluminum cladding and europium solubility in SWSA-6 groundwater. The bounding europium radionuclide near-field release rates peaked at about 1.3 Ci/year total for /sup 152,154,155/Eu in 1987 for the lower bound, and at about 420 Ci/year in 1992 for the upper bound. The near-field release rates of /sup 55/Fe, /sup 59/Ni, /sup 60/Co, and /sup 63/Ni from stainless steel and cobalt alloy components, as well as of /sup 10/Be, /sup 41/Ca, and /sup 55/Fe from beryllium reflectors, were calculated for the next 100 years, assuming bulk waste corrosion was the release-rate-limiting step. Under the most conservative assumptions for the reflectors, the current (1986) total radionuclide release rate was calculated to be about 1.2 x 10/sup -4/ Ci/year, decreasing by 1992 to a steady release of about 1.5 x 10/sup -5/ Ci/year due primarily to /sup 41/Ca. 50 refs., 13 figs., 8 tabs.

  6. Closure Alternatives for Municipal Waste Landfills.Study Case: Municipal Waste Landfill Medias,Sibiu County

    Directory of Open Access Journals (Sweden)

    MIHĂIESCU R.

    2010-12-01

    Full Text Available In the recent decades, the environmental impact produced by municipal solid wastes has received specialattention. All new EU countries are involved in the process of implementation of the European Council Directive31/99/EC on the landfill of waste in the European Union. As consequence National legislation, adapted to fit the EUrequirements, focuses on integrated waste management and environmental control of municipal solid waste landfills,from start-up to closure and assimilation into the environment. In Romania, by Government decision, HG 349/2005,was established the obligatoriness of closing unconform waste landfills located in urban areas starting at July 2009. Asconsequence the owner of municipal waste landfill Medias started the proceedings of closure for the landfill. The aim ofthis study is to compare, from an environmental point of view, different alternatives for the closure of the municipalsolid waste landfill Somard-Medias (Romania.

  7. Is bioexsiccation releasing dioxins?

    Energy Technology Data Exchange (ETDEWEB)

    Benfenati, E.; Mariani, G.; Lodi, M.; Reitano, G.; Fanelli, R. [' ' Mario Negri' ' Institute for Pharmacological Research, Milan (Italy)

    2004-09-15

    Bioexsiccation is a relatively new process to treat urban solid wastes. We studied the possible release of dioxins from this process, measuring dioxin concentration in the emissions from a bioexsiccation plant. As a comparison, we measured atmospheric levels nearby the plant. The biofilter treating gaseous emissions was also evaluated to assess its efficiency. Dioxin concentrations in the biofilter effluent were lower than both those before the biofilter and the nearby atmosphere. In the last years the management and treatment of solid urban wastes produced some improved processes, in a general attempt to cope with the problem of the huge amount of wastes produced by the modern society. Bio-exsiccation of waste aims at affording a much more biologically inert and manageable material compared to the original waste. In this process the urban solid waste is kept under an air stream for about two weeks. The waste undergoes biological transformation, due to fermentation, which produces an increase of the temperature up to 60-70 C. At the end of the process the weight waste is typically reduced by one third, due to the loss of water and to the degradation of putrescible compounds. Since this is a relatively new industrial process, we studied the possible release of dioxins in the atmospheric emissions of the bioexsiccation plant.

  8. Spray calcination of nuclear wastes

    Energy Technology Data Exchange (ETDEWEB)

    Bonner, W.F.; Blair, H.T.; Romero, L.S.

    1976-01-01

    The spray calciner is a relatively simple machine; operation is simple and is easily automated. Startup and shutdown can be performed in less than an hour. A wide variety of waste compositions and concentrations can be calcined under easily maintainable conditions. Spray calcination of all commercial fuel reprocessor high-level liquid wastes and mixed high and intermediate-level wastes have been demonstrated. Wastes have been calcined containing over 2M sodium. Thus waste generated during plant startup and shutdown can be blended with normal waste and calcined. Spray calcination of ILLW has also been demonstrated. A remotely replaceable atomizing nozzle has been developed for use in plant scale equipment. The 6 mm (0.25 inch) orifice and ceramic tip offer freedom from plugging and erosion thus nozzle replacement should be required only after several months operation. Calciner capacity of over 75 l/h (20 gal/h) has been demonstrated in pilot scale equipment. Sintered stainless steel filters are effective in deentraining over 99.9 percent of the solids that result from calcining the feedstock. Since such a small amount of radionuclides escape the calciner the volume of recycle required from the effluent treatment system is very small. The noncondensable off-gas volume is also low, less than 0.5 m/sup 3//min (15 scfm) for a liquid feedrate of 75 l/hr (20 gal/hr). Calcine holdup in the calciner is less than 1 kg, thus the liquid feedrate is directly relatable to calcine flowrate. The calcine produced is very fine and reactive. Successful remote operation and maintenance of a heated wall spray calciner has been demonstrated while processing actual high-level waste. During these operations radionuclide volatilization from the calciner was acceptably low. 8 figures. (DLC)

  9. Start-Ups and External Equity: The Role of Entrepreneurial Experience

    OpenAIRE

    Peter A. Zaleski

    2010-01-01

    A long-standing problem for most business start-ups is acquiring external equity during the first year of operations. In explaining the financing decisions of business start-ups, Meyer’s (1984) pecking order theory serves as a logical working hypothesis. Treating the pecking order to be the resolution to an information problem about the potential profitability of a business startup, this paper analyzes the determinants of obtaining external equity. Special consideration is given to the role o...

  10. Tokamak startup: problems and scenarios related to the transient phases of ignited tokamak operations

    Energy Technology Data Exchange (ETDEWEB)

    Sheffield, J.

    1985-01-01

    During recent years improvements have been made to tokamak startup procedures, which are important to the optimization of ignited tokamaks. The use of rf-assisted startup and noninductive current drive has led to substantial reduction and even complete elimination of the volt-seconds used during startup, relaxing constraints on poloidal coil, vacuum vessel, and structure design. This paper reviews these and other improvements and discusses the various bulk heating techniques that may be used to ignite a D-T plasma.

  11. Ideology as resource in entrepreneurial journalism: The French online news startup Mediapart

    OpenAIRE

    Wagemans, Andrea; Witschge, Tamara; Deuze, Mark

    2016-01-01

    The emergence of a startup culture in the field of journalism is global: since the early years of the twenty-first century, new independent journalism companies have formed around the world. Although setting up one's own journalistic practice is not particularly novel in the news industry, the last couple of years have witnessed exponential growth in the startup space. In this context we chose to look more closely at one of the more successful recent online news startups: the French site Medi...

  12. The Defense Waste Processing Facility: Two Years of Radioactive Operation

    Energy Technology Data Exchange (ETDEWEB)

    Marra, S.L. [Westinghouse Savannah River Company, AIKEN, SC (United States); Gee, J.T.; Sproull, J.F.

    1998-05-01

    The Defense Waste Processing Facility (DWPF) at the Savannah River Site in Aiken, SC is currently immobilizing high level radioactive sludge waste in borosilicate glass. The DWPF began vitrification of radioactive waste in May, 1996. Prior to that time, an extensive startup test program was completed with simulated waste. The DWPF is a first of its kind facility. The experience gained and data collected during the startup program and early years of operation can provide valuable information to other similar facilities. This experience involves many areas such as process enhancements, analytical improvements, glass pouring issues, and documentation/data collection and tracking. A summary of this experience and the results of the first two years of operation will be presented.

  13. Impact of chemical plant start-up emissions on ambient ozone concentration

    Science.gov (United States)

    Ge, Sijie; Wang, Sujing; Xu, Qiang; Ho, Thomas

    2017-09-01

    Flare emissions, especially start-up flare emissions, during chemical plant operations generate large amounts of ozone precursors that may cause highly localized and transient ground-level ozone increment. Such an adverse ozone impact could be aggravated by the synergies of multiple plant start-ups in an industrial zone. In this paper, a systematic study on ozone increment superposition due to chemical plant start-up emissions has been performed. It employs dynamic flaring profiles of two olefin plants' start-ups to investigate the superposition of the regional 1-hr ozone increment. It also summaries the superposition trend by manipulating the starting time (00:00-10:00) of plant start-up operations and the plant distance (4-32 km). The study indicates that the ozone increment induced by simultaneous start-up emissions from multiple chemical plants generally does not follow the linear superposition of the ozone increment induced by individual plant start-ups. Meanwhile, the trend of such nonlinear superposition related to the temporal (starting time and operating hours of plant start-ups) and spatial (plant distance) factors is also disclosed. This paper couples dynamic simulations of chemical plant start-up operations with air-quality modeling and statistical methods to examine the regional ozone impact. It could be helpful for technical decision support for cost-effective air-quality and industrial flare emission controls.

  14. Novel start-up circuit with enhanced power-up characteristic for bandgap references

    DEFF Research Database (Denmark)

    Tuan Vu, Cao; Wisland, Dag T.; Lande, Tor Sverre

    This paper presents a new start-up circuit for low-power bandgap reference (BGR) voltage generators. The BGR is designed for providing a stable 0.3 V power supply for application in low power wireless sensor nodes. The BGR has an enhanced power-up characteristic and demonstrates a reduction...... of the total stand-by current. Simulated results confirm that the proposed start-up circuit does not affect the performance of the BGR even though the supply voltage (VDD) is higher and has more stable power-up characteristic than the conventional start-up circuits. The new start-up circuit is designed with 65...

  15. Novel start-up circuit with enhanced power-up characteristic for bandgap references

    DEFF Research Database (Denmark)

    Tuan Vu, Cao; Wisland, Dag T.; Lande, Tor Sverre;

    This paper presents a new start-up circuit for low-power bandgap reference (BGR) voltage generators. The BGR is designed for providing a stable 0.3 V power supply for application in low power wireless sensor nodes. The BGR has an enhanced power-up characteristic and demonstrates a reduction...... of the total stand-by current. Simulated results confirm that the proposed start-up circuit does not affect the performance of the BGR even though the supply voltage (VDD) is higher and has more stable power-up characteristic than the conventional start-up circuits. The new start-up circuit is designed with 65...

  16. Bootstrap finance: the art of start-ups.

    Science.gov (United States)

    Bhide, A

    1992-01-01

    Entrepreneurship is more popular than ever: courses are full, policymakers emphasize new ventures, managers yearn to go off on their own. Would-be founders often misplace their energies, however. Believing in a "big money" model of entrepreneurship, they spend a lot of time trying to attract investors instead of using wits and hustle to get their ideas off the ground. A study of 100 of the 1989 Inc. "500" list of fastest growing U.S. start-ups attests to the value of bootstrapping. In fact, what it takes to start a business often conflicts with what venture capitalists require. Investors prefer solid plans, well-defined markets, and track records. Entrepreneurs are heavy on energy and enthusiasm but may be short on credentials. They thrive in rapidly changing environments where uncertain prospects may scare off established companies. Rolling with the punches is often more important than formal plans. Striving to adhere to investors' criteria can diminish the flexibility--the try-it, fix-it approach--an entrepreneur needs to make a new venture work. Seven principles are basic for successful start-ups: get operational fast; look for quick break-even, cash-generating projects; offer high-value products or services that can sustain direct personal selling; don't try to hire the crack team; keep growth in check; focus on cash; and cultivate banks early. Growth and change are the start-up's natural environment. But change is also the reward for success: just as ventures grow, their founders usually have to take a fresh look at everything again: roles, organization, even the very policies that got the business up and running.

  17. Success and Failure in University-Based Startups

    Science.gov (United States)

    Dehn, J.; Webley, P.; Cunningham, K. W.

    2014-12-01

    Adapting from a traditional government-funded research program to supporting the work through a start-up company is a difficult (and often not successful) transition. This is made more challenging in that with the relative decline in federal funding for the sciences the transition is forced on many researchers as a matter of survival. The business model of traditional research is not that different from that of the private sector; the development of an idea, models or mock-ups of the product, pitching to sources of funding, creating and marketing the product. However they differ significantly in the environment in which they are applied, as well as in the life span of a project or product. The environments for pitching an idea and gaining investment are very different in academia from that of the private sector, and most academics are stymied by the new approach. In addition, many universities labor under the illusion that start-ups will be a windfall, when in reality they represent a long term investment that will not pay out for many years. This extended timeline is also something new to academics, though persistence pays and a project may take years to fund, after it is complete and the publications written, many in the geosciences go on to new ideas. If a business is to be successful it must continue with a product long term, and develop new ideas around it. A hopefully successful balance of these approaches is being tried at the University of Alaska Fairbanks, where start-ups can build upon university intellectual property and use university resources to build a successful business. In turn the business supports research and development, primarily through faculty, staff and students at the university.

  18. Permanent start-up instrumentation for maintenance outages

    Energy Technology Data Exchange (ETDEWEB)

    Cuttler, J.M. [Cuttler and Associates Inc., Mississauga, Ontario (Canada); Nasimi, E.; Gill, H.; Scrannage, R.; Paquette, P. [Bruce Power, Tiverton, Ontario (Canada)

    2011-07-01

    This paper assesses the need and feasibility of permanent start-up instrumentation detectors to monitor photoneutron flux during maintenance outages. CANDU ion chamber systems were designed to remain on scale for ten weeks after reactor shutdown. A requirement was imposed in the mid-1990s to put the reactor into an overpoisoned guaranteed shutdown state whenever it is shut down and not actively undergoing a restart. Due to the high gadolinium concentration, the ion chamber systems go off scale within three weeks. Operating policies and procedures require the neutron flux and its rate of change to be monitored when fuel is in the reactor. (author)

  19. Blogging business step-by-step startup guide

    CERN Document Server

    magazine, Entrepreneur

    2014-01-01

    This kit includes: Essential industry and business-specific startup steps with worksheets, calculators, checklists and more. Entrepreneur Editors' Start Your Own Business, a guide to starting any business and surviving the first three years. Downloadable, customizable business letters, sales letters, and other sample documents. Entrepreneur's Small Business Legal Toolkit. Blogs are still one of the internet's fastest-growing phenomena–and one of the best and easiest ways to make money online. Packed with the latest blog tools, tricks, and up-and-coming trends, this fully revised edition teache

  20. PARAMETRIC EFFECTS OF ANTI-FOAM COMPOSITION, SIMULANT PROPERTIES AND NOBLE METALS ON THE GAS HOLDUP AND RELEASE OF A NON-NEWTONIAN WASTE SLURRY SIMULANT

    Energy Technology Data Exchange (ETDEWEB)

    Guerrero, H; Charles Crawford, C; Mark Fowley, M

    2008-08-07

    Gas holdup tests were performed in bench-scale and small-scale mechanically-agitated mixing systems at the Savannah River National Laboratory (SRNL) for a simulant of waste from the Hanford Tank 241-AZ-101. These featured additions of DOW Corning Q2-3183A anti-foam agent. Results indicated that this anti-foam agent (AFA) increased gas holdup in the waste simulant by about a factor of four and, counter-intuitively, that the holdup increased as the non-newtonian simulant shear strength decreased (apparent viscosity decreased). Such results raised the potential of increased flammable gas retention in Hanford Waste Treatment and Immobilization Plant (WTP) vessels mixed by air sparging and pulse-jet mixers (PJMs) during a Design Basis Event (DBE). Additional testing was performed to determine the effects of simulant properties, composition of alternate AFAs, and presence of trace noble metals. Key results are that: (1) Increased gas holdup resulting from addition of Q2-3183A is due to a decrease in surface tension that supports small bubbles which have low rise velocities. (2) Dow Corning 1520-US AFA shows it to be a viable replacement to Dow Corning Q2-3183A AFA. This alternative AFA, however, requires significantly higher dosage for the same anti-foam function. (3) Addition of noble metals to the AZ-101 waste simulant does not produce a catalytic gas retention effect with the AFA.

  1. Medical irradiation, radioactive waste and misinformation. A press release from the French Academy of Medicine; Irradiation medicale, dechets, desinformation: un avis de l'Academie de medecine

    Energy Technology Data Exchange (ETDEWEB)

    The, G. de; Tubiana, M

    2002-07-01

    The Academy of Medicine, worried by the problems that poses for public opinion the medical irradiation, the radioactive wastes and some erroneous information that these subjects give rise to, considers useful to give an advice based on objective data. (N.C.)

  2. Start-up analysis for automotive PEM fuel cell systems

    Science.gov (United States)

    De Francesco, M.; Arato, E.

    The development of fuel cell cars can play an important role in resolving transport problems, due to the high environmental compatibility and high efficiency of this kind of vehicle. Among the different types of fuel cells, proton-exchange membrane fuel cells (PEMFCs) are considered the best solution for automotive applications at the moment. In this work, constructive criteria are discussed with the aim of obtaining a power generation module adaptable to a wide range of cars. A particular problem in accomplishing the overall project is represented by the definition of the compressor system for air feeding. In this work, the design approach to the problem will be delineated: some options are reviewed and the best solution is analysed. The transient response of the system (fuel cell and compressor) is investigated in order to optimise the start-up running through a model of a fuel cell stack and a compressor simulation. The model and its results are proposed as a work procedure to solve the problem, by varying external conditions: in fact, to perform the system start-up under stable conditions, the air relative humidity and temperature must be maintained in a proper range of values. The approach here presented has been utilised for the definition of the characteristics of the power module and layout of a middle-size hybrid city bus in the framework of a project promoted by the European Union.

  3. Initial Plasma Startup Test on SUNIST Spherical Tokamak

    Institute of Scientific and Technical Information of China (English)

    Wang Ying(王莹); Zeng Li(曾立); He Yexi(何也熙); SUMST Team

    2003-01-01

    The goal of the Sino-United Spherical Tokamak (SUNIST) at Tsinghua University is to extend the understanding of toroidal plasma physics at a low aspect ratio (R/a ≈ 1.3) and to demonstrate a maintainable target plasma by non-inductive startup. The SUNIST device is designed to operate with up to 13 kA of ohmic heating field current, and to 0.15 T of toroidal field at 10 kA of discharge current. All of the poloidal fields can provide 30 mVs of Volt-seconds transformer. Experimental results of plasma startup show that SUNIST has remarkable characteristics of high ramp rate (dIp/dt ≈ 50 MA/s ), high normalized current IN of about 2.8 (IN = Ip/aBT),and high-efficiency (Ip/IROD ≈ 0.4) production of plasma current while operating at a low toroidal field. Major disruption phenomena have not been observed from magnetic diagnostics of all testing shots. Initial discharges with 52 kA of plasma current (exceeding the designed value of 50 kA),2 ms of pulse length and 50 MA/s of ramp rate have been achieved easily with pre-ionized filament.

  4. Automated Startup of the CEBAF 45 MeV Injector

    Science.gov (United States)

    Kehne, D.; Letta, P.; Dunham, B.; Kazimi, R.

    1997-05-01

    In order to improve the speed and reproducibility of restoring the beam in the CEBAF 45 MeV injector after a full or partial shutdown of the accelerator, a program has been written using the Tcl/Tk scripting language to automate most of the required steps. The procedure is separated into three main parts. The first consists of preliminary checks that verify that the hardware is set correctly and that systems are ready to be activated. The second part turns on the main interlocked systems including high power magnets and RF. The final step turns on the beam and verifies that the beam quality is satisfactory by measuring the transmission, orbit, bunch length, transverse emittance and match, energy spread, and dispersion. Minor corrections for phasing are also performed in the program. In order to identify inefficiencies in the startup, each step is timed and parameter changes are logged so that system drifts can be tracked. This paper describes the software implementation, the logic to achieve a successful startup, and efficiency results.

  5. Rapid Start-up and Loading of an Attached Growth, Simultaneous Nitrification/Denitrification Membrane Aerated Bioreactor

    Science.gov (United States)

    Meyer, Caitlin E.; Pensinger, Stuart; Pickering, Karen D.; Barta, Daniel; Shull, Sarah A.; Vega, Letticia M.; Christenson, Dylan; Jackson, W. Andrew

    2015-01-01

    Membrane aerated bioreactors (MABR) are attached-growth biological systems used for simultaneous nitrification and denitrification to reclaim water from waste. This design is an innovative approach to common terrestrial wastewater treatments for nitrogen and carbon removal and implementing a biologically-based water treatment system for long-duration human exploration is an attractive, low energy alternative to physiochemical processes. Two obstacles to implementing such a system are (1) the "start-up" duration from inoculation to steady-state operations and (2) the amount of surface area needed for the biological activity to occur. The Advanced Water Recovery Systems (AWRS) team at JSC explored these two issues through two tests; a rapid inoculation study and a wastewater loading study. Results from these tests demonstrate that the duration from inoculation to steady state can be reduced to under two weeks, and that despite low ammonium removal rates, the MABRs are oversized.

  6. Strategies for merging microbial fuel cell technologies in water desalination processes: Start-up protocol and desalination efficiency assessment

    Science.gov (United States)

    Borjas, Zulema; Esteve-Núñez, Abraham; Ortiz, Juan Manuel

    2017-07-01

    Microbial Desalination Cells constitute an innovative technology where microbial fuel cell and electrodialysis merge in the same device for obtaining fresh water from saline water with no energy-associated cost for the user. In this work, an anodic biofilm of the electroactive bacteria Geobacter sulfurreducens was able to efficiently convert the acetate present in synthetic waste water into electric current (j = 0.32 mA cm-2) able to desalinate water. .Moreover, we implemented an efficient start-up protocol where desalination up to 90% occurred in a desalination cycle (water production:0.308 L m-2 h-1, initial salinity: 9 mS cm-1, final salinity: treatment method combined with other well established desalination technologies such as reverse osmosis (RO) or reverse electrodialysis.

  7. Medical waste: a minimal hazard.

    Science.gov (United States)

    Keene, J H

    1991-11-01

    Medical waste is a subset of municipal waste, and regulated medical waste comprises less than 1% of the total municipal waste volume in the United States. As part of the overall waste stream, medical waste does contribute in a relative way to the aesthetic damage of the environment. Likewise, some small portion of the total release of hazardous chemicals and radioactive materials is derived from medical wastes. These comments can be made about any generated waste, regulated or unregulated. Healthcare professionals, including infection control personnel, microbiologists, public health officials, and others, have unsuccessfully argued that there is no evidence that past methods of treatment and disposal of regulated medical waste constitute any public health hazard. Historically, discovery of environmental contamination by toxic chemical disposal has followed assurances that the material was being disposed of in a safe manner. Therefore, a cynical public and its elected officials have demanded proof that the treatment and disposal of medical waste (i.e., infectious waste) do not constitute a public health hazard. Existent studies on municipal waste provide that proof. In order to argue that the results of these municipal waste studies are demonstrative of the minimal potential infectious environmental impact and lack of public health hazard associated with medical waste, we must accept the following: that the pathogens are the same whether they come from the hospital or the community, and that the municipal waste studied contained waste materials we now define as regulated medical waste.(ABSTRACT TRUNCATED AT 250 WORDS)

  8. Argonne National Laboratory`s photooxidation organic mixed-waste treatment system

    Energy Technology Data Exchange (ETDEWEB)

    Shearer, T.L.; Torres, T.; Conner, C. [Argonne National Lab., IL (United States)] [and others

    1997-12-01

    This paper describes the installation and startup testing of the Argonne National Laboratory-East (ANL-E) photo-oxidation organic mixed-waste treatment system. This system will treat organic mixed (i.e., radioactive and hazardous) waste by oxidizing the organics to carbon dioxide and inorganic salts in an aqueous media. The residue will be treated in the existing radwaste evaporators. The system is installed in the waste management facility at the ANL-E site in Argonne, Illinois.

  9. 78 FR 38001 - Reconsideration of Certain Startup/Shutdown Issues: National Emission Standards for Hazardous Air...

    Science.gov (United States)

    2013-06-25

    ... startup system (like a startup boiler feed pump, if applicable) and transitions to bring emission controls... Emission Standards for Hazardous Air Pollutants From Coal- and Oil- Fired Electric Utility Steam Generating Units and Standards of Performance for Fossil-Fuel-Fired Electric Utility, Industrial-...

  10. Navigating the Interface between Design Education and Fashion Business Start-up

    Science.gov (United States)

    Mills, Colleen E.

    2012-01-01

    Purpose: The purpose of this paper is to address the interface between design education and business start-up in the designer fashion industry (DFI) and provide a new framework for reflecting on ways to improve design education and graduates' business start-up preparedness. Design/methodology/approach: This interpretive study employed…

  11. The Emergence of the Lean Global Startup as a New Type of Firm

    Directory of Open Access Journals (Sweden)

    Erik Stavnsager Rasmussen

    2015-11-01

    Full Text Available This article contributes to the interplay between international entrepreneurship, innovation networks, and early internationalization research by emphasizing the need to conceptualize and introduce a new type of firm: the lean global startup. It discussed two different paths in linking the lean startup and born-global internationalization strategies. The first path refers to generic lean startups that have undertaken a rapid internationalization strategy (i.e., lean-to-global startups. The second path refers to startups that have started operating on global scale since their inception and adopted the lean startup approach by seamlessly synergizing their global and lean product development activities. The article emphasizes several aspects that could be used as part of the theoretical foundation for conceptualizing lean global startups as a special new type of firm: i the emergent nature of their business models, including the challenges of partnership development on a global scale; ii the inherently relational nature of the global resource allocation processes; iii the integration of the entrepreneurial, effectuation, and global marketing perspectives; iv the need to deal with a high degree of uncertainty, including the uncertainty associated with cross-border business operations; and v linking the ex-ante characteristics of lean startups with the ex-post characteristics of born-global firms in order to develop a technology adoption marketing perspective that considers the “crossing the chasm” process as a successful entry into a global market niche.

  12. Start-ups, long- and short-term survivors, and their contribution to employment growth

    NARCIS (Netherlands)

    Fritsch, Michael; Noseleit, Florian

    2013-01-01

    This study documents that the survival of start-ups is central in explaining the relationship between entry and regional employment growth. Distinguishing between start-ups according to the period of their survival shows that the positive effect of new business formation on employment growth is main

  13. A Studio Based Approach to Enhancing Decision Making in Sme Start-Up

    NARCIS (Netherlands)

    Sol, H G; Ejiri, A.H.; Nabukenya, J.

    2011-01-01

    The start-up phase plays an important role in the success and survival of many enterprises, which greatly depends on adequate and timely services for decision making. However, deciding to startup a mining Small and Medium Enterprise (SME) is a challenging task for many entrepreneurs in Uganda. Resea

  14. Navigating the Interface between Design Education and Fashion Business Start-up

    Science.gov (United States)

    Mills, Colleen E.

    2012-01-01

    Purpose: The purpose of this paper is to address the interface between design education and business start-up in the designer fashion industry (DFI) and provide a new framework for reflecting on ways to improve design education and graduates' business start-up preparedness. Design/methodology/approach: This interpretive study employed…

  15. Start-ups, long- and short-term survivors, and their contribution to employment growth

    NARCIS (Netherlands)

    Fritsch, Michael; Noseleit, Florian

    This study documents that the survival of start-ups is central in explaining the relationship between entry and regional employment growth. Distinguishing between start-ups according to the period of their survival shows that the positive effect of new business formation on employment growth is

  16. Startup of Pumping Units in Process Water Supplies with Cooling Towers at Thermal and Nuclear Power Plants

    Energy Technology Data Exchange (ETDEWEB)

    Berlin, V. V., E-mail: vberlin@rinet.ru; Murav’ev, O. A., E-mail: muraviov1954@mail.ru; Golubev, A. V., E-mail: electronik@inbox.ru [National Research University “Moscow State University of Civil Engineering,” (Russian Federation)

    2017-03-15

    Aspects of the startup of pumping units in the cooling and process water supply systems for thermal and nuclear power plants with cooling towers, the startup stages, and the limits imposed on the extreme parameters during transients are discussed.

  17. Swedish nuclear waste efforts

    Energy Technology Data Exchange (ETDEWEB)

    Rydberg, J.

    1981-09-01

    After the introduction of a law prohibiting the start-up of any new nuclear power plant until the utility had shown that the waste produced by the plant could be taken care of in an absolutely safe way, the Swedish nuclear utilities in December 1976 embarked on the Nuclear Fuel Safety Project, which in November 1977 presented a first report, Handling of Spent Nuclear Fuel and Final Storage of Vitrified Waste (KBS-I), and in November 1978 a second report, Handling and Final Storage of Unreprocessed Spent Nuclear Fuel (KBS II). These summary reports were supported by 120 technical reports prepared by 450 experts. The project engaged 70 private and governmental institutions at a total cost of US $15 million. The KBS-I and KBS-II reports are summarized in this document, as are also continued waste research efforts carried out by KBS, SKBF, PRAV, ASEA and other Swedish organizations. The KBS reports describe all steps (except reprocessing) in handling chain from removal from a reactor of spent fuel elements until their radioactive waste products are finally disposed of, in canisters, in an underground granite depository. The KBS concept relies on engineered multibarrier systems in combination with final storage in thoroughly investigated stable geologic formations. This report also briefly describes other activities carried out by the nuclear industry, namely, the construction of a central storage facility for spent fuel elements (to be in operation by 1985), a repository for reactor waste (to be in operation by 1988), and an intermediate storage facility for vitrified high-level waste (to be in operation by 1990). The R and D activities are updated to September 1981.

  18. Release characteristics of mercury in the backlight units during waste processing of LCDs%废LCD显示器背光源模组拆解过程中汞的释放特征

    Institute of Scientific and Technical Information of China (English)

    李金惠; 王芳

    2013-01-01

    As the Minamata Convention on Mercury comes into effect in 2013,mercury-containing wastes must be more carefully processed by the international community.The Chinese government has been addressing mercury pollution control in recent years.The dismantling of waste liquid crystal displays (LCD) can easily result in the release of mercury in the backlight which must be carefully handled.This study analyzes the presence of mercury in the backlight,the transfer path and release characteristics of the mercury once the backlight is broken,and the total quantity of the mercury generated by the waste LCD dismantling industry.About 1/3 of the mercury reacts with the glass during use of the backlight with about 2/3 left in the lamp vessel.There is approximately 76.8 kg of backlight per ton of waste LCD,which should be treated as hazardous waste.The waste LCD TV dismantling industry then releases more than 1 t of mercury into the environment through various channels per year,of which about 200 kg of the mercury vapor goes into the atmosphere.%随着2013年首个全球汞排放公约的获得通过,含汞废物受到国际社会的广泛关注,中国对于汞污染排放的管理和整顿力度将逐步加大.由于在废液晶显示器(liquid crystal display,LCD)拆解过程中,背光源模组中所含的汞较易释放扩散出来,受到研究者的普遍重视.该文就废LCD背光源中汞的存在状态、LCD拆解过程中背光灯管破碎后汞的转移路径和释放特征以及废LCD拆解行业所产生的汞排放总量等方面展开研究,并得出以下结论:首先,对于单根冷阴极荧光灯背光源(backlight cold cathode fluorescent lamp,BCCFL)而言,在使用过程中会有总质量1/3左右的汞因与灯管材料发生反应而不再以易检测到的形式存在,2/3的汞则留在灯管内;其次,每吨废LCD液晶电视会产生含汞的背光源模组约76.8 kg;再次,对于废LCD液晶电视拆解行业而言,每年有超过1t汞通过不同

  19. Start-up Success in a Small Island State: A Study among Entrepreneurs in Malta

    Directory of Open Access Journals (Sweden)

    Leonie Baldacchino

    2008-05-01

    Full Text Available This study focuses on entrepreneurs in the small island state of Malta and investigates whether starting up and running an enterprise is facilitated or hindered by being in a small island environment. Specifically it asks (1 whether being on a small island, on the periphery of a major market facilitates or hinders entrepreneurship and start-up success; (2 whether Malta’s cultural context and enterprise environment affect entrepreneurship and start-up success; (3 what the key success factors among Maltese start-ups are; and (4 how are creativity and innovation reflected in Maltese start-ups. Qualitative research among 13 start-ups is supported by telephone-based research among a sample of 90 respondents. Findings contribute to the pool of business expertise and context-specific information from small island states that is often missing from the international literature.

  20. Liquid secondary waste: Waste form formulation and qualification

    Energy Technology Data Exchange (ETDEWEB)

    Cozzi, A. D. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Dixon, K. L. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Hill, K. A. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Nichols, R. L. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

    2017-07-31

    and water characteristic curves) were comparable to the properties measured on the Savannah River Site (SRS) Saltstone waste form. Future testing should include efforts to first; 1) determine the rate and amount of ammonia released during each unit operation of the treatment process to determine if additional ammonia management is required, then; 2) reduce the ammonia content of the ETF concentrated brine prior to solidification, making the waste more amenable to grouting, or 3) manage the release of ammonia during production and ongoing release during storage of the waste form, or 4) develop a lower pH process/waste form thereby precluding ammonia release.

  1. Startup of anaerobic fluidized bed reactors with acetic acid as the substrate.

    Science.gov (United States)

    Hsu, Y; Shieh, W K

    1993-02-05

    The startup of anaerobic fluidized bed reactors, which use Manville R-633 beads as the growth support media, acetate enriched bacterial culture as the inoculum, and acetic acid as the sole substrate, is studied. Tow startup strategies are evaluated: one based on maximum and stable substrate utilization and another based on maximum substrate loading controlled by reactor pH. The startup process is characterized using a number of operational parameters.The reactors again excellent total organic carbon (TOC) removal (i.e., > 97% at a feed concentration of 5000 mg TOC/L) and stable methane production (i.e., 0.90 L CH(4)/g TOC, where TOC(r) is TOC removed) at a early stage of the startup process, regardless of the strategies applied. The loading can be increased rapidly without the danger of being overloaded. Significant losses of growth support media and biomass caused by gas effervescence at higher loadings limits the maximum loading that can be safely applied during startup process.A high reactor immobilized biomass inventory is achievable using the porous growth support media (e.g., Manville 633 beads). A rapid increase in loading creates a substrate rich environment that yields more viable reactor biomass. Both substrate utilization rate (batch and continuous) and immobilized biomass inventory stabilize concomitantly at the late stage of the startup process, indicating the attainment of steady-state conditions in reactors. Therefore, they are better parameters that TOC removal and methane production for characterizing the entire startup process of aerobic fluidized bed reactor.The strategy based on maximum substrate loading controlled by reactor pH significantly shortens the startup time. In this case, the reactor attains steady-state conditions approximately 140 days after startup. On the other hand, a startup time of 200 days is required when the strategy based maximum substrate utilization is adopted.

  2. The relationship between start-ups, market mobility and employment growth : An empirical analysis for Dutch regions

    NARCIS (Netherlands)

    Koster, Sierdjan; van Stel, Andre

    2014-01-01

    Abstract Recent literature suggests two mechanisms through which the start-up of new firms contributes to economic development: the growth of start-ups and competition among incumbent firms induced by the start-ups. While existing studies derive the competition effect indirectly, this paper deploys

  3. Dual-Fuel Truck Fleet: Start-Up Experience

    Energy Technology Data Exchange (ETDEWEB)

    NREL

    1998-09-30

    Although dual-fuel engine technology has been in development and limited use for several years, it has only recently moved toward full-scale operational capability for heavy-duty truck applications. Unlike a bifuel engine, which has two separate fuel systems that are used one at a time, a dual-fuel engine uses two fuel systems simultaneously. One of California's South Coast Air Quality Management District (SCAQMD) current programs is a demonstration of dual-fuel engine technology in heavy-duty trucks. These trucks are being studied as part of the National Renewable Energy Laboratory's (NREL's) Alternative Fuel Truck Program. This report describes the start-up experience from the program.

  4. W and Z boson Productions in CMS at LHC startup

    CERN Document Server

    Dobur, Didar

    2009-01-01

    We report on potential for measurement of W and Z boson production, as well as the production in association with jets. Of particular interest are jet multiplicity and $P_{\\rm T}$ distributions. The 10 to $100~{\\rm pb}^{-1}$ datasets expected in the startup year of operation of LHC are likely to already provide information beyond the reach of the Tevatron collider both in jet multiplicity and $P_{\\rm T}$ range. We are especially interested in understanding the ratios of W+jets to Z+jets distributions by comparing them to next-to-leading order Monte Carlo generators, as these processes present a formidable background for searches of new physics phenomena.

  5. Start-up of two moving bed membrane bioreactors treating saline wastewater contaminated by hydrocarbons.

    Science.gov (United States)

    Campo, R; Di Prima, N; Freni, G; Giustra, M G; Di Bella, G

    2016-01-01

    This work aims to assess the acclimation of microorganisms to a gradual increase of salinity and hydrocarbons, during the start-up of two moving bed membrane bioreactors (MB-MBRs) fed with saline oily wastewater. In both systems an ultrafiltration membrane was used and two types of carriers were employed: polyurethane sponge cubes (MB-MBRI) and polyethylene cylindrical carriers (MB-MBRII). A decreasing dilution factor of slops has been adopted in order to allow biomass acclimation. The simultaneous effect of salinity and hydrocarbons played an inhibitory role in biomass growth and this resulted in a decrease of the biological removal efficiencies. A reduction of bound extracellular polymeric substances and a simultaneous release of soluble microbial products (SMPs) were observed, particularly in the MB-MBRII system, probably due to the occurrence of a greater suspended biomass stress as response to the recalcitrance of substrate. On the one hand, a clear attachment of biomass occurred only in MB-MBRI and this affected the fouling deposition on the membrane surface. The processes of detachment and entrapment of biomass, from and into the carriers, significantly influenced the superficial cake deposition and its reversibility. On the other hand, in MB-MBRII, the higher production of SMPs implied a predominance of the pore blocking.

  6. Comparison of ICRP2 and ICRP30 for estimating the dose and adverse health effects from potential radionuclide releases from a geologic waste repository

    Energy Technology Data Exchange (ETDEWEB)

    Runkle, G.E.; Soldat, J.K.

    1982-01-01

    This paper presents a comparison of the calculated risk of adverse health effects from the radionuclides considered in the inventory of a high-level waste repository using the ICRP2 and ICRP30 internal dosimetry models. A CRPC (cancer risk per curie) index was calculated to compare the two models. The CRPC indices for the ICRP30 model are approximately 2 to 20 times higher than the ICRP2 indices for most radionuclides for ingestion intakes. However, the /sup 237/Np index is approximately 200 times greater for the ICRP30 model and the /sup 228/Ra and /sup 226/Ra indices are approximately 30 to 90 times greater for the ICRP2 model. Generally, there is closer agreement of the CRPC indices for the inhalation intakes. A scenario that considers a U-tube effect and withdrawal of water from wells downdip from the repository was analyzed. This analysis, based on a hypothetical waste disposal site, considered groundwater transport and environmental transport with subsequent uptake by the human via ingestion and inhalation. The ICRP30 risks are higher by approximately 20 at 10,000 years post closure for the ingestion pathway. However, the ICRP2 risks are higher by factors of approximately 2 to 10 at times greater than 50,000 years. Differences in the mathematical modeling assumptions, gut uptakes and other metabolic parameters between the two models account for most of the variability in the risk estimates.

  7. Radioactive waste tank ventilation system incorporating tritium control

    Energy Technology Data Exchange (ETDEWEB)

    Rice, P.D. [ICF Kaiser Hanford Company, Richland, WA (United States)

    1997-08-01

    This paper describes the development of a ventilation system for radioactive waste tanks at the U.S. Department of Energy`s (DOE) Hanford Site in Richland, Washington. The unique design of the system is aimed at cost-effective control of tritiated water vapor. The system includes recirculation ventilation and cooling for each tank in the facility and a central exhaust air clean-up train that includes a low-temperature vapor condenser and high-efficiency mist eliminator (HEME). A one-seventh scale pilot plant was built and tested to verify predicted performance of the low-temperature tritium removal system. Tests were conducted to determine the effectiveness of the removal of condensable vapor and soluble and insoluble aerosols and to estimate the operating life of the mist eliminator. Definitive design of the ventilation system relied heavily on the test data. The unique design features of the ventilation system will result in far less release of tritium to the atmosphere than from conventional high-volume dilution systems and will greatly reduce operating costs. NESHAPs and TAPs NOC applications have been approved, and field construction is nearly complete. Start-up is scheduled for late 1996. 3 refs., 4 figs., 2 tabs.

  8. L'évaluation et le financement des start-up Internet

    OpenAIRE

    2001-01-01

    This paper discusses some phenomena in the corporate finance of internet start-ups that emerged during the “internet buble” between 1998-2000. The advent of nternet start-ups had a major impact on the investment flow and the operations of the venture capital industry in the US and in Europe. It is argued that some of these transformations could be explained by the potential for specific agency conflicts in the financing of internet start-ups. The paper then turns to a discussion of initial pu...

  9. Research on the soft start-up performance of hydro-viscous drive

    Institute of Scientific and Technical Information of China (English)

    WEI Jian-hua(魏建华); CHEN Ning(陈宁)

    2004-01-01

    The principle and structure of hydro-viscous drive(HVD) set is introduced. Through theoretical analysis of the HVD set start-up steadiness, the conclusions were obtained that the non-linearity of the pressure performance curve and dynamic pressure instability of the pilot-operated electro-hydraulic pressure relief valve, which is used for the HVD speed regulating purpose and usually works within micro flow-rate and low oil pressure state, are the main causes of the poor start-up steadiness. So a special speed regulating valve for HVD set is developed, with which the start-up steadiness of HVD set is much improved.

  10. Development Trajectory of an Innovation-Based Environmental Technology Start-Up

    OpenAIRE

    Saukkonen, Juha; Vänttinen, Kari

    2016-01-01

    This research paper focuses on the growth models of new business ventures and their applicability to a specific type of start-up, environmental technology–based growth company via a case study. Start-ups companies are a focal point of interest of this decade. Start-ups develop products and services in conditions of market and technological uncertainty and competitive volatility. Due to their crucial role in the net job creation there is a growing need and interest to understand, model and dev...

  11. Optimization of turbine startup: Some experimental results from a propeller runner

    Science.gov (United States)

    Gagnon, M.; Jobidon, N.; Lawrence, M.; Larouche, D.

    2014-03-01

    The turbine startup is a transient event generating high amplitude stress cycles in runner blades which might reduce significantly the life expectancy of the runner. Our goal is to use the increased range of possibilities offered by newer governing system to optimize the wicket gates control pattern in order to reduce the amplitude of the strain transient in the runner blade during startup. In this paper, we present our success in defining an optimal wicket gates control pattern for the startup of a newly commissioned propeller runner.

  12. Waste Sites - Municipal Waste Operations

    Data.gov (United States)

    NSGIC Education | GIS Inventory — A Municipal Waste Operation is a DEP primary facility type related to the Waste Management Municipal Waste Program. The sub-facility types related to Municipal Waste...

  13. 煤矸石重金属释放活性及其污染土壤的生态风险评价%Characteristics of Heavy Metals Release from Coal Waste and Potential Ecological Risk Assessment of Contaminated Soil Around Coal Waste Piles

    Institute of Scientific and Technical Information of China (English)

    张明亮; 岳兴玲; 杨淑英

    2011-01-01

    通过野外采样与室内实验分析煤矸石重金属的释放活性,并利用潜在生态风险评价法分析煤矸石山周边土壤污染及其潜在生态风险特征。结果表明,实验用煤矸石中重金属主要以残渣态存在,Cu、Zn、Pb、Cr和Cd的残渣态分别占其总量的56.86%,53.27%,72.01%,68.61%和75.93%,不易发生释放迁移,但少量酸溶态和氧化物结合态重金属易被淋溶后在矸石山周围土壤中累积并造成重金属污染。煤矸石山周边土壤重金属含量随着距离的增加呈现减少趋势,表明周边土壤受到煤矸石重金属污染,并且在土壤表层重金属含量最高,加大了重金属进入食物链危害人体健康的风险。通过潜在生态风险评价研究,采样区属于重金属Cd和Pb风险突出区,煤矸石距离5~10 m处潜在生态风险指数为272.34和164.34,属于中等潜在生态风险,其他各点潜在生态风险指数范围为94.62~141.79,属于轻微生态风险。%Characteristics of heavy metals release from coal waste and potential ecological risk assessment of contaminated soil around coal waste piles were studied.The results showed that:(1)Residual fraction was the main fraction of heavy metal in coal waste,such as Cu,Zn,Pb,Cr and Cd accounted for 56.86%,53.27%,72.01%,68.61% and 75.93%,which could not easily release from coal waste,but few acid soluble fraction and oxidizable fraction could release and contaminate the soil;(2)Soil heavy metal contents decreased with the distance from coal waste piles increase,which showed the soil was contaminated,and heavy metal contents of top layer were highest than other soil layer,which could cause the heavy metal into crop and endanger human body.Potential ecological risk assessment was used to evaluate the contamination situation of various heavy metals,and Cd,Pb were the main ecological risk factor.The area within 5 m and 10 m distance from coal waste piles belongs to mild ecological risk

  14. Mathematical modeling and analysis of heat pipe start-up from the frozen state

    Energy Technology Data Exchange (ETDEWEB)

    Jang, J.H.; Faghri, A. [Wright State Univ., Dayton, OH (United States); Chang, W.S.; Mahefkey, E.T. [Wright Research and Development Center, Wright-Patterson, OH (United States)

    1989-08-01

    The start-up process of a frozen heat pipe is described and a complete mathematical model for the start-up of the frozen heat pipe is developed based on the existing experimental data, which is simplified and solved numerically. The two-dimensional transient model for the wall and wick is coupled with the one-dimensional transient model for the vapor flow when vaporization and condensation occur at the interface. A parametric study is performed to examine the effect of the boundary specification at the surface of the outer wall on the successful start-up from the frozen state. For successful start-up, the boundary specification at the outer wall surface must melt the working substance in the condenser before dry-out takes place in the evaporator.

  15. Mathematical modeling and analysis of heat pipe start-up from the frozen state

    Science.gov (United States)

    Jang, J. H.; Faghri, A.; Chang, W. S.; Mahefkey, E. T.

    1990-01-01

    The start-up process of a frozen heat pipe is described and a complete mathematical model for the start-up of the frozen heat pipe is developed based on the existing experimental data, which is simplified and solved numerically. The two-dimensional transient model for the wall and wick is coupled with the one-dimensional transient model for the vapor flow when vaporization and condensation occur at the interface. A parametric study is performed to examine the effect of the boundary specification at the surface of the outer wall on the successful start-up from the frozen state. For successful start-up, the boundary specification at the outer wall surface must melt the working substance in the condenser before dry-out takes place in the evaporator.

  16. Optimization on start-up process of high-pressure rotor for large power steam turbine

    Directory of Open Access Journals (Sweden)

    Du Qiu-Wan

    2016-01-01

    Full Text Available This paper combines thermal-structure coupling technique and pattern search optimization algorithm to establish an optimization system for the start-up process of a turbine unit. Firstly, a finite element model for thermal-structure coupling calculation is established to accurately analyze the transient temperature field and thermal stress field, which can obtain the thermal stress distribution during start-up process. Afterwards, a program of optimization on rotor start-up process is exploited to improve the time allocation in each operating stage of start-up process, which minimizes the maximum equivalent stress of rotor. The maximum equivalent stress has reduced 25.7% after the optimization, which reveals obvious effect.

  17. Optimization of steam-vortex plasma-torch start-up

    Science.gov (United States)

    Mikhailov, B. I.

    2011-12-01

    We propose a new optimal method of steam-vortex plasma-torches start-up; this method completely prevents the danger of water steam condensation in the arc chamber and all undesirable consequences of it.

  18. Diffusion-controlled startup of a gas-loaded liquid-metal heat pipe

    Science.gov (United States)

    Ponnappan, R.; Boehman, L. I.; Mahefkey, E. T.

    1990-07-01

    Liquid-metal heat pipes have exhibited difficulties starting up from a frozen-state. Inert gas loading is a possible solution to the frozen-state startup problem. The present study deals with the diffusion-controlled startup analysis and testing of an argon-loaded, 2-m-long, stainless steel-sodium heat pipe of the double-walled type with artery channel and long adiabatic section. A two-dimensional, quasi-steady state, binary vapor-gas diffusion model determined the energy transport rate of vapor at the diffusion front. The analytical solution to the diffusion problem provided the vapor flux, which in turn was used in the one-dimensional transient thermal model of the heat pipe to predict the time rate-of-change of temperature and position of the hot front. The experimental test results successfully demonstrated the startup of a gas-loaded sodium heat pipe and validated the diffusion model of the startup.

  19. Ecological characteristics of seeding sludge triggering a prompt start-up of anammox.

    Science.gov (United States)

    Tao, Yu; Gao, Da-Wen; Wang, Hao-Yu; de Kreuk, Merle; Ren, Nan-Qi

    2013-04-01

    Anammox start-up can be limited by the availability of seeding biomass in some areas. Previous studies have listed suitable alternative seeding sludge for anammox start-up such as anaerobic digestion sludge and conventional activated sludge (CAS), the ecological reasons behind has long been ignored. In this study, the inherent ecological factors that trigger a prompt start-up of anammox were identified, focusing on the initial relative abundance and concentration of anammox bacteria. An external membrane bioreactor was utilized as an enriching tool due to its suitability of retaining cells. Results revealed that a high initial concentration of anammox bacteria benefitted the start-up, meanwhile an even community seeding sludge (Gini coefficient0.5). The discovery reminds to select the seeding sludge that is ecologically appropriate rather than to only care for the type of sludge in general. Copyright © 2013 Elsevier Ltd. All rights reserved.

  20. The Impact of Start-up Grants on Firm Performance in Estonia

    OpenAIRE

    Siret Vildo; Jaan Masso

    2013-01-01

    As in economic theory start-up enterprises have been seen as important sources of growth, the government support measures to enterprises have been a common practice around the world for decades. As the governmental support to enterprises is often of a considerable amount of money there is a need to assess its efficiency. In the present article we study the impact of Estonian start-up grants distributed in 2002 and 2003 on various indicators of firm performance with econometric methods, namely...

  1. START-UP AND GROWTH OF IMMIGRANT SMALL BUSINESSES: THE IMPACT OF SOCIAL AND HUMAN CAPITAL

    OpenAIRE

    JENNIFER M. SEQUEIRA; Abdul A Rasheed

    2006-01-01

    Networks, and their resulting social capital, can be key determinants of successful business start-up for immigrant entrepreneurs. Historically, immigrants have settled in communities characterized by networks that consist of strong ties. Network theory suggests that in addition to strong ties, success also requires the development of weak ties. In this paper, we develop a model of the relationships between strong and weak ties, and the likelihood of a business start-up and its subsequent gro...

  2. >venture>: Support for Early Stage Start-ups and Potential Entrepreneurs.

    Science.gov (United States)

    Kauz, Lukas

    2014-12-01

    >venture>, the leading Swiss-wide business plan competition, is an ideal partner for young start-ups and entrepreneurs. For the upcoming tenth anniversary edition the competition will receive an update. Building upon a successful base of the past nine editions and equipped with contemporary networking events and more know-how transferring seminars, >venture> will fit even better into the Swiss start-up ecosystem.

  3. Cooperation between large companies and start-ups: the access to drive disruptive innovation

    OpenAIRE

    Bruse, Florian; Böhmer, Annette Isabel; Lindemann, Udo

    2016-01-01

    According to Christopher Clayton’s Innovator’s Dilemma large corporations face a threat of disruptive innovation. By use of products and services with a moderate amount of new technologies, new business models can be created, which later on oust established companies. Particularly start-ups seem to be more prone to drive disruptive innovations than large corporations. This paper illustrates the need for cooperation between large companies and start-ups in order to pursue disruptive innovation...

  4. Environmental mitigation for SCC initiation of BWR core internals by hydrogen injection during start-up

    Energy Technology Data Exchange (ETDEWEB)

    Dozaki, K.; Abe, A.; Nagata, N.; Takiguchi, H. [The Japan Atomic Power Co. (Japan)

    2004-07-01

    Hydrogen injection into the reactor water has been applied to many BWR power stations. Since hydrogen injected accelerates recombination of oxidant generated by water radiolysis, oxidant concentration, such as dissolved oxygen concentration in reactor water can be reduced. As the result of the reduction of oxidant concentration, Electrochemical Corrosion Potential (ECP) at the surface of structural material can be lowered. Lowered ECP moderates Stress Corrosion Cracking (SCC) sensitivity of structural materials, such as stainless steels. As usual, hydrogen injection system begins to work after the plant start-up is finished, when the condition of normal operation is established. Accordingly, Hydrogen Water Chemistry (HWC) does not cover all the period of plant operation. As far as SCC crack growth is considered, loss of HWC during plant start-up does not result in significant crack growth, because of duration of plant start-up is much shorter than that of plant normal operation, when HWC condition is being satisfied. However, the reactor water environment and load conditions during a plant start-up may contribute to the initiation of SCC. It is estimated that the core internals are subjected to the strain rate that may cause susceptibility to SCC initiation during start-up. Dissolved oxygen (DO) and hydrogen peroxide (H{sub 2}O{sub 2}) has a peak, and ECP is in high levels during start-up. Therefore it is beneficial to perform hydrogen injection during start-up as well in order to suppress SCC initiation. We call it HWC During Start-up (HDS) here. (orig.)

  5. START-UP AND GROWTH OF IMMIGRANT SMALL BUSINESSES: THE IMPACT OF SOCIAL AND HUMAN CAPITAL

    OpenAIRE

    JENNIFER M. SEQUEIRA; Abdul A Rasheed

    2006-01-01

    Networks, and their resulting social capital, can be key determinants of successful business start-up for immigrant entrepreneurs. Historically, immigrants have settled in communities characterized by networks that consist of strong ties. Network theory suggests that in addition to strong ties, success also requires the development of weak ties. In this paper, we develop a model of the relationships between strong and weak ties, and the likelihood of a business start-up and its subsequent gro...

  6. Summary of radioactive solid waste received in the 200 Areas during calendar year 1995

    Energy Technology Data Exchange (ETDEWEB)

    Hladek, K.L.

    1996-06-06

    Westinghouse Hanford Company manages and operates the Hanford Site 200 Area radioactive solid waste storage and disposal facilities for the US Department of Energy, Richland Operations Office. These facilities include radioactive solid waste disposal sites and radioactive solid waste storage areas. This document summarizes the amount of radioactive materials that have been buried and stored in the 200 Area radioactive solid waste storage and disposal facilities since startup in 1944 through calendar year 1995. This report does not include backlog waste, solid radioactive wastes in storage or disposed of in other areas, or facilities such as the underground tank farms. Unless packaged within the scope of WHC-EP-0063, Hanford Site Solid Waste Acceptance Criteria, liquid waste data are not included in this document. This annual report provides a summary of the radioactive solid waste received in the both the 200-East and 200-West Areas during the calendar year 1995.

  7. Resonance investigation of pump-turbine during startup process

    Science.gov (United States)

    He, L. Y.; Wang, Z. W.; Kurosawa, S.; Nakahara, Y.

    2014-12-01

    The causes of resonance of a certain model pump-turbine unit during startup process were investigated in this article. A three-dimensional full flow path analysis model which contains spiral case, stay vanes, guide vanes, runner, gaps outside the runner crown and band, and draft tube was constructed. The transient hydraulic excitation force of full flow path was analyzed under five conditions near the resonance region. Based on one-way fluid- structure interaction (FSI) analysis model, the dynamic stress characteristics of the pump-turbine runner was investigated. The results of pressure pulsation, vibration mode and dynamic stress obtained from simulation were consistent with the test results. The study indicated that the hydraulic excitation frequency (Zg*fn) Hz due to rotor-stator interference corresponding to the natural frequency of 2ND+4ND runner mode is the main cause of resonance. The relationship among pressure pulsation, vibration mode and dynamic stress was discussed in this paper. The results revealed the underlying causes of the resonance phenomenon.

  8. Electron cyclotron plasma startup in the GDT experiment

    Science.gov (United States)

    Yakovlev, D. V.; Shalashov, A. G.; Gospodchikov, E. D.; Solomakhin, A. L.; Savkin, V. Ya.; Bagryansky, P. A.

    2017-01-01

    We report on a new plasma startup scenario in the gas dynamic trap (GDT) magnetic mirror device. The primary 5 MW neutral beam injection (NBI) plasma heating system fires into a sufficiently dense plasma target (‘seed plasma’), which is commonly supplied by an arc plasma generator. In the reported experiments, a different approach to seed plasma generation is explored. One of the channels of the electron cyclotron resonance (ECR) heating system is used to ionize the neutral gas and build up the density of plasma to a level suitable for NBI capture. After a short transition of approximately 1 ms the discharge becomes essentially similar to a standard one initiated by the plasma gun. This paper presents the discharge scenario and experimental data on the seed plasma evolution during ECRH, along with the dependencies on incident microwave power, magnetic configuration and pressure of a neutral gas. The characteristics of the consequent high-power NBI discharge are studied and differences from the conventional scenario are discussed. A theoretical model describing the ECR breakdown and the seed plasma accumulation in a large-scale mirror trap is developed on the basis of the GDT experiment.

  9. Electron-cyclotron plasma startup in the GDT experiment

    CERN Document Server

    Yakovlev, D V; Gospodchikov, E D; Solomakhin, A L; Savkin, V Ya; Bagryansky, P A

    2016-01-01

    The paper reports on a new plasma startup scenario in the Gas Dynamic Trap (GDT) magnetic mirror device. The primary 5 MW neutral beam injection (NBI) plasma heating system fires into a sufficiently dense plasma target ("seed plasma"), which is commonly supplied by an arc plasma generator. In the reported experiments, a different approach to seed plasma generation is explored. One of the channels of the electron cyclotron resonance (ECR) heating system is used to ionize the neutral gas and build up the density of plasma to a level suitable for NBI capture. After a short transition (about 1 ms) the discharge becomes essentially similar to a standard one initiated by the plasma gun. The paper presents the discharge scenario and experimental data on the seed plasma evolution during ECR heating, along with the dependencies on incident microwave power, magnetic configuration and pressure of a neutral gas. The characteristics of consequent high-power NBI discharge are studied and differences to the conventional sce...

  10. Advancing Non-Solenoidal Startup on the Pegasus ST

    Science.gov (United States)

    Reusch, J. A.; Barr, J. L.; Bodner, G. M.; Bongard, M. W.; Burke, M. G.; Fonck, R. J.; Pachicano, J. L.; Perry, J. M.; Richner, N. J.; Rodriguez Sanchez, C.; Schlossberg, D. J.

    2016-10-01

    The Pegasus experiment utilizes compact, edge-localized current sources (Ainj 2 - 4 cm2, Iinj 10 kA, Vinj 1 kV) for non-solenoidal local helicity injection (LHI) startup. Recent campaigns are comparing two injector geometries that vary the differing relative contributions of DC helicity input and non-solenoidal inductive voltages. A predictive 0-D model that treats the plasma as a resistive element with time-varying inductance and enforces Ip limits from Taylor relaxation was tested with inward growth of the plasma current channel using injectors on the outboard midplane. Strong inductive drive arises from plasma shape evolution and poloidal field (PF) induction. A major unknown in the model is the resistive dissipation, and hence the electron confinement. Te (R) profile measurements in LHI show centrally-peaked Te > 100 eV while the plasma is coupled to the injectors, suggesting LHI confinement is not strongly stochastic. A second campaign utilizes new injectors in the lower divertor region. This geometry trades subtler relaxation field programming and reduced PF induction for higher HI rates. Present efforts are developing relaxation methods at high BT, with relaxation at BT , inj > 0.15 T achieved to date via higher Iinj and PF manipulation. Conceptual design studies of coaxial helicity injection (CHI) and ECH heating systems for Pegasus have been initiated to explore direct comparison of LHI to CHI with and without ECH assist. Supported by US DOE Grants DE-FG02-96ER54375, DE-SC0006928.

  11. Pinon Pine power project nears start-up

    Energy Technology Data Exchange (ETDEWEB)

    Tatar, G.A. [Sierra Pacific Power Co., Reno, NV (United States); Gonzalez, M. [Foster Wheeler USA Corp., Clinton, NJ (United States); Mathur, G.K. [M.W. Kellogg Co., Houston, TX (United States)

    1997-12-31

    The IGCC facility being built by Sierra Pacific Power Company (SPPCo) at their Tracy Station in Nevada is one of three IGCC facilities being cost-shared by the US Department of Energy (DOE) under their Clean Coal Technology Program. The specific technology to be demonstrated in SPPCo`s Round Four Project, known as the Pinon Pine IGCC Project, includes the KRW air blown pressurized fluidized bed gasification process with hot gas cleanup coupled with a combined cycle facility based on a new GE 6FA gas turbine. Construction of the 100 MW IGCC facility began in February 1995 and the first firing of the gas turbine occurred as scheduled on August 15, 1996 with natural gas. Mechanical completion of the gasifier and other outstanding work is due in January 1997. Following the startup of the plant, the project will enter a 42 month operating and testing period during which low sulfur western and high sulfur eastern or midwestern coals will be processed.

  12. Control Valve Trajectories for SOFC Hybrid System Startup

    Energy Technology Data Exchange (ETDEWEB)

    Gorrell, Megan; Banta, Larry; Rosen, William; Restrepo, Bernardo; Tucker, David

    2012-07-01

    Control and management of cathode airflow in a solid oxide fuel cell gas turbine hybrid power system was analyzed using the Hybrid Performance (HyPer) hardware simulation at the National Energy Technology (NETL), U.S. Department of Energy. This work delves into previously unexplored operating practices for HyPer, via simultaneous manipulation of bypass valves and the electric load on the generator. The work is preparatory to the development of a Multi-Input, Multi-Output (MIMO) controller for HyPer. A factorial design of experiments was conducted to acquire data for 81 different combinations of the manipulated variables, which consisted of three air flow control valves and the electric load on the turbine generator. From this data the response surface for the cathode airflow with respect to bypass valve positions was analyzed. Of particular interest is the control of airflow through the cathode during system startup and during large load swings. This paper presents an algorithm for controlling air mass flow through the cathode based on a modification of the steepest ascent method.

  13. Acquisition Integration Models: How Large Companies Successfully Integrate Startups

    Directory of Open Access Journals (Sweden)

    Peter Carbone

    2011-10-01

    Full Text Available Mergers and acquisitions (M&A have been popular means for many companies to address the increasing pace and level of competition that they face. Large companies have pursued acquisitions to more quickly access technology, markets, and customers, and this approach has always been a viable exit strategy for startups. However, not all deals deliver the anticipated benefits, in large part due to poor integration of the acquired assets into the acquiring company. Integration can greatly impact the success of the acquisition and, indeed, the combined company’s overall market success. In this article, I explore the implementation of several integration models that have been put into place by a large company and extract principles that may assist negotiating parties with maximizing success. This perspective may also be of interest to smaller companies as they explore exit options while trying to ensure continued market success after acquisition. I assert that business success with acquisitions is dependent on an appropriate integration model, but that asset integration is not formulaic. Any integration effort must consider the specific market context and personnel involved.

  14. International Space Station Lithium-Ion Battery Start-Up

    Science.gov (United States)

    Dalton, Penni J.; North, Tim; Bowens, Ebony; Balcer, Sonia

    2017-01-01

    International Space Station Lithium-Ion Battery Start-Up.The International Space Station (ISS) primary Electric Power System (EPS) was originally designed to use Nickel-Hydrogen (Ni-H2) batteries to store electrical energy. The electricity for the space station is generated by its solar arrays, which charge batteries during insolation for subsequent discharge during eclipse. The Ni-H2 batteries are designed to operate at a 35 depth of discharge (DOD) maximum during normal operation in a Low Earth Orbit. As the oldest of the 48 Ni-H2 battery Orbital Replacement Units (ORUs) has been cycling since September 2006, these batteries are now approaching their end of useful life. In 2010, the ISS Program began the development of Lithium-Ion (Li-ion) batteries to replace the Ni-H2 batteries and concurrently funded a Li-Ion ORU and cell life testing project. The first set of 6 Li-ion battery replacements were launched in December 2016 and deployed in January 2017. This paper will discuss the Li-ion battery on-orbit start-up and the status of the Li-Ion cell and ORU life cycle testing.

  15. Failure prediction of government funded start-up firms

    Directory of Open Access Journals (Sweden)

    Oliver Lukason

    2017-08-01

    Full Text Available This study aims to create a prediction model that would forecast the bankruptcy of government funded start-up firms (GFSUs. Also, the financial development patterns of GFSUs are outlined. The dataset consists of 417 Estonian GFSUs, of which 75 have bankrupted before becoming five years old and 312 have survived for five years. Six financial ratios have been calculated for one (t+1 and two (t+2 years after firms have become active. Weighted logistic regression analysis is applied to create the bankruptcy prediction models and consecutive factor and cluster analyses are applied to outline the financial patterns. Bankruptcy prediction models obtain average classification accuracies, namely 63.8% for t+1 and 67.8% for t+2. The bankrupt firms are distinguished with a higher accuracy than the survived firms, with liquidity and equity ratios being the useful predictors of bankruptcy. Five financial patterns are detected for GFSUs, but bankrupt GFSUs do not follow any distinct patterns that would be characteristic only to them.

  16. Hanford Site Secondary Waste Roadmap

    Energy Technology Data Exchange (ETDEWEB)

    Westsik, Joseph H.

    2009-01-29

    performance requirements, waste composition, preliminary waste form screening, waste form development, process design and support, and validation. The regulatory and performance requirements activity will provide the secondary waste-form performance requirements. The waste-composition activity will provide workable ranges of secondary waste compositions and formulations for simulants and surrogates. Preliminary waste form screening will identify candidate waste forms for immobilizing the secondary wastes. The waste form development activity will mature the waste forms, leading to a selected waste form(s) with a defensible understanding of the long-term release rate and input into the critical decision process for a secondary waste treatment process/facility. The process and design support activity will provide a reliable process flowsheet and input to support a robust facility design. The validation effort will confirm that the selected waste form meets regulatory requirements. The final outcome of the implementation of the secondary waste roadmap is the compliant, effective, timely, and cost-effective disposal of the secondary wastes. The work necessary to address the programmatic, regulatory, and technical risks and uncertainties identified through the Secondary Waste Roadmap Workshop are assembled into several program needs elements. Programmatic/Regulatory needs include: • Select and deploy Hanford tank waste supplemental treatment technology • Provide treatment capability for secondary waste streams from tank waste treatment • Develop consensus on secondary waste form acceptance. Technology needs include: • Define secondary waste composition ranges and uncertainties • Identify and develop waste forms for secondary waste immobilization and disposal • Develop test methods to characterize secondary waste form performance. Details for each of these program elements are provided.

  17. Stochastic multicomponent reactive transport analysis of low quality drainage release from waste rock piles: Controls of the spatial distribution of acid generating and neutralizing minerals

    Science.gov (United States)

    Pedretti, Daniele; Mayer, K. Ulrich; Beckie, Roger D.

    2017-06-01

    In mining environmental applications, it is important to assess water quality from waste rock piles (WRPs) and estimate the likelihood of acid rock drainage (ARD) over time. The mineralogical heterogeneity of WRPs is a source of uncertainty in this assessment, undermining the reliability of traditional bulk indicators used in the industry. We focused in this work on the bulk neutralizing potential ratio (NPR), which is defined as the ratio of the content of non-acid-generating minerals (typically reactive carbonates such as calcite) to the content of potentially acid-generating minerals (typically sulfides such as pyrite). We used a streamtube-based Monte-Carlo method to show why and to what extent bulk NPR can be a poor indicator of ARD occurrence. We simulated ensembles of WRPs identical in their geometry and bulk NPR, which only differed in their initial distribution of the acid generating and acid neutralizing minerals that control NPR. All models simulated the same principal acid-producing, acid-neutralizing and secondary mineral forming processes. We show that small differences in the distribution of local NPR values or the number of flow paths that generate acidity strongly influence drainage pH. The results indicate that the likelihood of ARD (epitomized by the probability of occurrence of pHuniversally safe; threshold to ensure non-acidic waters in practical applications. Our results suggest that new methods that explicitly account for mineralogical heterogeneity must be sought when computing effective (upscaled) NPR values at the scale of the piles.

  18. Two-port network model and startup criteria for thermoacoustic oscillators

    Institute of Scientific and Technical Information of China (English)

    HU XingHua; ZHANG XiaoQing; WANG HuiLing; SHU ShuiMing

    2009-01-01

    The startup process of a thermoacoustic engine is a self-excited oscillation process generated in in-homogeneous acoustic media. To reveal these coupling relations between various influential factors is an important task of basic research on thermoacoustics. In this paper thermoacoustic engines are re-garded as thermoacoustic oscillators consisting of the active network and the passive network. Ac-cordingly, the two-port Y-parameter for relevant component is derived, and standing wave and traveling wave thermoacoustic engine are described by the negative-resistance and feedback model, respec-tively. The relevant two-port network topology is given as well. The startup criteria for thermoacoustic oscillators are obtained by using Nyquist instability criterion. The model prediction of startup parame-ters, particularly, startup frequency and mode characteristic are in agreement with that of experimental results reported in the literature. Moreover, with topological graphs it is verified that standing wave engines would start up in a negative-resistance state and there would exist high frequency modes in thermoacoustic-Stirling engines. By investigating into the frequency response of thermoacoustic sys-tem, this method proposed can achieve such an objective that these effects of operating and structural parameters of engine on startup modes and startup temperature can be revealed in an analytical way.Thus this approach to test and check thermal stability can be provided in a design phase, instead of using empirical frequency to design thermoacoustic systems.

  19. Radioactive liquid wastes discharged to ground in the 200 Areas during 1976

    Energy Technology Data Exchange (ETDEWEB)

    Mirabella, J.E.

    1977-05-09

    An overall summary is presented giving the radioactive liquid wastes discharged to ground during 1976 and since startup (for both total and decayed depositions) within the Production and Waste Management Division control zone (200 Area plateau). Overall summaries are also presented for 200 East Area and for 200 West Area. The data contain an estimate of the radioactivity discharged to individual ponds, cribs and specific retention sites within the Production and Waste Management Division during 1976 and from startup through December 31, 1976; an estimate of the decayed activities from startup through 1976; the location and reference drawings of each disposal site; and the usage dates of each disposal site. The estimates for the radioactivity discharged and for decayed activities dicharged from startup through December 31, 1976 are based upon Item 4 of the Bibliography. The volume of liquid discharged to the ponds also includes major nonradioactive streams. The wastes discharged during 1976 to each active disposal site are detailed on a month-to-month basis, along with the monthly maximum concentration and average concentration data. An estimate of the radioactivity discharged to each active site along with the remaining decayed activities is given.

  20. 76 FR 80451 - Commercial and Industrial Solid Waste Incineration Units: Reconsideration and Proposed Amendments...

    Science.gov (United States)

    2011-12-23

    ... Chloride HF Hydrogen Fluoride (HF) Hg Mercury HMI Hospital, Medical and Infectious HMIWI Hospital, Medical... Startup, Shutdown, and Malfunction SVOC Semi-Volatile Organic Compound SWDA Solid Waste Disposal Act TBtu... Voluntary Consensus Standards VOC Volatile Organic Compound WWW Worldwide Web A. Does this document...

  1. Radioactive liquid wastes discharged to ground in the 200 Areas during 1978

    Energy Technology Data Exchange (ETDEWEB)

    Anderson, J. D.; Poremba, B. E.

    1979-03-26

    This document is issued quarterly for the purpose of summarizing the radioactive liquid wastes that have been discharged to the ground in the 200 Areas. In addition to data for 1978, cumulative data since plant startup are presented. Also, in this document is a listing of decayed activity to the various plant sites.

  2. Residential Waste

    DEFF Research Database (Denmark)

    Christensen, Thomas Højlund; Fruergaard, Thilde; Matsufuji, Y.

    2011-01-01

    are discussed in this chapter. Characterizing residential waste is faced with the problem that many residences already divert some waste away from the official collection systems, for example performing home composting of vegetable waste and garden waste, having their bundled newspaper picked up by the scouts...... twice a year or bringing their used furniture to the flea markets organized by charity clubs. Thus, much of the data available on residential waste represents collected waste and not necessarily all generated waste. The latter can only be characterized by careful studies directly at the source......Residential waste comes from residential areas with multi-family and single-family housing and includes four types of waste: household waste, garden waste, bulky waste and household hazardous waste. Typical unit generation rates, material composition, chemical composition and determining factors...

  3. Residential Waste

    DEFF Research Database (Denmark)

    Christensen, Thomas Højlund; Fruergaard, Thilde; Matsufuji, Y.

    2011-01-01

    Residential waste comes from residential areas with multi-family and single-family housing and includes four types of waste: household waste, garden waste, bulky waste and household hazardous waste. Typical unit generation rates, material composition, chemical composition and determining factors...... are discussed in this chapter. Characterizing residential waste is faced with the problem that many residences already divert some waste away from the official collection systems, for example performing home composting of vegetable waste and garden waste, having their bundled newspaper picked up by the scouts...... twice a year or bringing their used furniture to the flea markets organized by charity clubs. Thus, much of the data available on residential waste represents collected waste and not necessarily all generated waste. The latter can only be characterized by careful studies directly at the source...

  4. COMMERCIAL SNF ACCIDENT RELEASE FRACTIONS

    Energy Technology Data Exchange (ETDEWEB)

    S.O. Bader

    1999-10-18

    The purpose of this design analysis is to specify and document the total and respirable fractions for radioactive materials that are released from an accident event at the Monitored Geologic Repository (MGR) involving commercial spent nuclear fuel (CSNF) in a dry environment. The total and respirable release fractions will be used to support the preclosure licensing basis for the MGR. The total release fraction is defined as the fraction of total CSNF assembly inventory, typically expressed as an activity inventory (e.g., curies), of a given radionuclide that is released to the environment from a waste form. The radionuclides are released from the inside of breached fuel rods (or pins) and from the detachment of radioactive material (crud) from the outside surfaces of fuel rods and other components of fuel assemblies. The total release fraction accounts for several mechanisms that tend to retain, retard, or diminish the amount of radionuclides that are available for transport to dose receptors or otherwise can be shown to reduce exposure of receptors to radiological releases. The total release fraction includes a fraction of airborne material that is respirable and could result in inhalation doses. This subset of the total release fraction is referred to as the respirable release fraction. Potential accidents may involve waste forms that are characterized as either bare (unconfined) fuel assemblies or confined fuel assemblies. The confined CSNF assemblies at the MGR are contained in shipping casks, canisters, or disposal containers (waste packages). In contrast to the bare fuel assemblies, the container that confines the fuel assemblies has the potential of providing an additional barrier for diminishing the total release fraction should the fuel rod cladding breach during an accident. However, this analysis will not take credit for this additional bamer and will establish only the total release fractions for bare unconfined CSNF assemblies, which may however be

  5. Hazardous Waste

    Science.gov (United States)

    ... you throw these substances away, they become hazardous waste. Some hazardous wastes come from products in our homes. Our garbage can include such hazardous wastes as old batteries, bug spray cans and paint ...

  6. Water transport during startup and shutdown of polymer electrolyte fuel cell stacks

    Energy Technology Data Exchange (ETDEWEB)

    Wang, X.; Tajiri, K.; Ahluwalia, R.K. [Argonne National Laboratory, 9700 S Cass Avenue, Argonne, IL 60439 (United States)

    2010-10-01

    A dynamic three-phase transport model is developed to analyze water uptake and transport in the membrane and catalyst layers of polymer electrolyte fuel cells during startup from subfreezing temperatures and subsequent shutdown. The initial membrane water content ({lambda}, the number of water molecules per sulfonic acid site) is found to be an important parameter that determines whether a successful unassisted self-start is possible. For a given initial subfreezing temperature at startup, there is a critical {lambda} ({lambda}{sub h}), above which self-start is not possible because the product water completely engulfs the catalyst layers with ice before the stack can warm-up to 0 C. There is a second value of {lambda} ({lambda}{sub l}), below which the stack can be self-started without forming ice. Between {lambda}{sub l} and {lambda}{sub h}, the stack can be self-started, but with intermediate formation of ice that melts as the stack warms up to 0 C. Both {lambda}{sub l} and {lambda}{sub h} are functions of the initial stack temperature, cell voltage at startup, membrane thickness, catalyst loading, and stack heat capacity. If the stack is purged during the previous shutdown by flowing air in the cathode passages, then depending on the initial amount of water in the membrane and gas diffusion layers and the initial stack temperature, it may not be possible to dry the membrane to the critical {lambda} for a subsequent successful startup. There is an optimum {lambda} for robust and rapid startup and shutdown. Startup and shutdown time and energy may be unacceptable if the {lambda} is much less than the optimum. Conversely, a robust startup from subfreezing temperatures cannot be assured if the {lambda} is much higher than this optimum. (author)

  7. Water transport during startup and shutdown of polymer electrolyte fuel cell stacks.

    Energy Technology Data Exchange (ETDEWEB)

    Wang, X.; Tajiri, K.; Ahluwalia, R.; Nuclear Engineering Division

    2010-10-01

    A dynamic three-phase transport model is developed to analyze water uptake and transport in the membrane and catalyst layers of polymer electrolyte fuel cells during startup from subfreezing temperatures and subsequent shutdown. The initial membrane water content (?, the number of water molecules per sulfonic acid site) is found to be an important parameter that determines whether a successful unassisted self-start is possible. For a given initial subfreezing temperature at startup, there is a critical ? (?h), above which self-start is not possible because the product water completely engulfs the catalyst layers with ice before the stack can warm-up to 0 C. There is a second value of ? (?l), below which the stack can be self-started without forming ice. Between ?l and ?h, the stack can be self-started, but with intermediate formation of ice that melts as the stack warms up to 0 C. Both ?l and ?h are functions of the initial stack temperature, cell voltage at startup, membrane thickness, catalyst loading, and stack heat capacity. If the stack is purged during the previous shutdown by flowing air in the cathode passages, then depending on the initial amount of water in the membrane and gas diffusion layers and the initial stack temperature, it may not be possible to dry the membrane to the critical ? for a subsequent successful startup. There is an optimum ? for robust and rapid startup and shutdown. Startup and shutdown time and energy may be unacceptable if the ? is much less than the optimum. Conversely, a robust startup from subfreezing temperatures cannot be assured if the ? is much higher than this optimum.

  8. Water transport during startup and shutdown of polymer electrolyte fuel cell stacks

    Science.gov (United States)

    Wang, X.; Tajiri, K.; Ahluwalia, R. K.

    A dynamic three-phase transport model is developed to analyze water uptake and transport in the membrane and catalyst layers of polymer electrolyte fuel cells during startup from subfreezing temperatures and subsequent shutdown. The initial membrane water content (λ, the number of water molecules per sulfonic acid site) is found to be an important parameter that determines whether a successful unassisted self-start is possible. For a given initial subfreezing temperature at startup, there is a critical λ (λ h), above which self-start is not possible because the product water completely engulfs the catalyst layers with ice before the stack can warm-up to 0 °C. There is a second value of λ (λ l), below which the stack can be self-started without forming ice. Between λ l and λ h, the stack can be self-started, but with intermediate formation of ice that melts as the stack warms up to 0 °C. Both λ l and λ h are functions of the initial stack temperature, cell voltage at startup, membrane thickness, catalyst loading, and stack heat capacity. If the stack is purged during the previous shutdown by flowing air in the cathode passages, then depending on the initial amount of water in the membrane and gas diffusion layers and the initial stack temperature, it may not be possible to dry the membrane to the critical λ for a subsequent successful startup. There is an optimum λ for robust and rapid startup and shutdown. Startup and shutdown time and energy may be unacceptable if the λ is much less than the optimum. Conversely, a robust startup from subfreezing temperatures cannot be assured if the λ is much higher than this optimum.

  9. Waste minimization handbook, Volume 1

    Energy Technology Data Exchange (ETDEWEB)

    Boing, L.E.; Coffey, M.J.

    1995-12-01

    This technical guide presents various methods used by industry to minimize low-level radioactive waste (LLW) generated during decommissioning and decontamination (D and D) activities. Such activities generate significant amounts of LLW during their operations. Waste minimization refers to any measure, procedure, or technique that reduces the amount of waste generated during a specific operation or project. Preventive waste minimization techniques implemented when a project is initiated can significantly reduce waste. Techniques implemented during decontamination activities reduce the cost of decommissioning. The application of waste minimization techniques is not limited to D and D activities; it is also useful during any phase of a facility`s life cycle. This compendium will be supplemented with a second volume of abstracts of hundreds of papers related to minimizing low-level nuclear waste. This second volume is expected to be released in late 1996.

  10. Mine Waste Disposal and Managements

    Energy Technology Data Exchange (ETDEWEB)

    Cheong, Young-Wook; Min, Jeong-Sik; Kwon, Kwang-Soo [Korea Institute of Geology Mining and Materials, Taejon (KR)] (and others)

    1999-12-01

    This research project deals with: Analysis and characterization of mine waste piles or tailings impoundment abandoned in mining areas; Survey of mining environmental pollution from mine waste impounds; Modelling of pollutants in groundwater around tailings impoundment; Demonstration of acid rock drainage from coal mine waste rock piles and experiment of seeding on waste rock surface; Development of a liner using tailings. Most of mine wastes are deposited on natural ground without artificial liners and capping for preventing contamination of groundwater around mine waste piles or containments. In case of some mine waste piles or containments, pollutants have been released to the environment, and several constituents in drainage exceed the limit of discharge from landfill site. Metals found in drainage exist in exchangeable fraction in waste rock and tailings. This means that if when it rains to mine waste containments, mine wastes can be pollutant to the environment by release of acidity and metals. As a result of simulation for hydraulic potentials and groundwater flow paths within the tailings, the simulated travel paths correlated well with the observed contaminant distribution. The plum disperse, both longitudinal and transverse dimensions, with time. Therefore liner system is a very important component in tailings containment system. As experimental results of liner development using tailings, tailings mixed with some portion of resin or cement may be used for liner because tailings with some additives have a very low hydraulic conductivity. (author). 39 refs.

  11. Summary of radioactive solid waste received in the 200 areas during calendar year 1997

    Energy Technology Data Exchange (ETDEWEB)

    Hagel, D.L.

    1998-06-25

    Waste Management Federal Services of Hanford Inc. manages and operates the Hanford Site 200 Area radioactive solid waste storage and disposal facilities for the US Department of Energy, Richland Operations Office under contract DE-AC06-87RL10930. These facilities include storage areas and disposal sites for radioactive solid waste. This document summarizes the amount of radioactive materials that have been buried and stored in the 200 Area radioactive solid waste storage and disposal facilities from startup in 1944 through calendar year 1997. This report does not include backlog waste, solid radioactive wastes in storage or disposed of in other areas, or facilities such as the underground tank farms. Unless packaged within the scope of WHC-EP-0063, Hanford Site Solid Waste Acceptance Cafeteria, liquid waste data are not included in this document.

  12. Summary of radioactive solid waste received in the 200 Areas during calendar year 1994

    Energy Technology Data Exchange (ETDEWEB)

    Anderson, J.D.; Hagel, D.L.

    1995-08-01

    Westinghouse Hanford Company manages and operates the Hanford Site 200 Area radioactive solid waste storage and disposal facilities for the US Department of Energy, Richland Field Office, under contract DE-AC06-87RL10930. These facilities include radioactive solid waste disposal sites and radioactive solid waste storage areas. This document summarizes the amount of radioactive material that has been buried and stored in the 200 Area radioactive solid waste storage and disposal facilities from startup in 1944 through calendar year 1994. This report does not include backlog waste: solid radioactive wastes in storage or disposed of in other areas or facilities such as the underground tank farms. Unless packaged within the scope of WHC-EP-0063, Hanford Site Solid Waste Acceptance Criteria (WHC 1988), liquid waste data are not included in this document.

  13. Summary of radioactive solid waste received in the 200 areas during calendar year 1997

    Energy Technology Data Exchange (ETDEWEB)

    Hagel, D.L.

    1998-06-25

    Waste Management Federal Services of Hanford Inc. manages and operates the Hanford Site 200 Area radioactive solid waste storage and disposal facilities for the US Department of Energy, Richland Operations Office under contract DE-AC06-87RL10930. These facilities include storage areas and disposal sites for radioactive solid waste. This document summarizes the amount of radioactive materials that have been buried and stored in the 200 Area radioactive solid waste storage and disposal facilities from startup in 1944 through calendar year 1997. This report does not include backlog waste, solid radioactive wastes in storage or disposed of in other areas, or facilities such as the underground tank farms. Unless packaged within the scope of WHC-EP-0063, Hanford Site Solid Waste Acceptance Cafeteria, liquid waste data are not included in this document.

  14. NCI Start-Up 2.0: An Evaluation Option License Program | NCI Technology Transfer Center | TTC

    Science.gov (United States)

    NCI's Start-Up Evaluation Option License minimizes barriers to entry faced by start-up companies that seek to license NIH technologies. The license encourages and supports the commercial development of early-stage technologies developed in the NIH Intramural Research Program. While the NIH has been quite flexible in structuring licenses for the benefit of start-up companies, one of the goals of the NIH Start-up License program is to further reduce the time and capital to negotiate and finalize an exclusive license agreement. | [google6f4cd5334ac394ab.html

  15. Trademark or patent? The effects of market structure, customer type and venture capital financing on start-ups' IP decisions

    OpenAIRE

    Vries, Geertjan; Pennings, Enrico; Block, Jörn

    2013-01-01

    textabstractWe analyze the initial intellectual property (IP) right of 4,703 start-up entrants in the US, distinguishing between trademark and patent applications. The results show that start-ups are more likely to file for a trademark instead of a patent when entering into more competitive market structures. Further, we find that start-ups with a focus on distribution that serves end-consumers are more likely to file for a trademark and that start-ups that operate upstream and sell to other ...

  16. Southeastern Environmental Resources Alliance [Status report on completion milestones incorporated in the Cooperative Agreement, and draft start-up plan March 24, 1995

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-12-31

    The Southeastern Environmental Resources Alliance (SERA) is a joint effort between the US Department of Energy, the states of Georgia and South Carolina, and Westinghouse Savannah River Company (WSRC). The original proposal for SERA, submitted under the Technology Reinvestment Project (TRP), is based on improving the competitiveness of manufacturers within Georgia and South Carolina by addressing the costs associated with environmental and waste management issues. By using the many technologies available through the national laboratories, universities, the Savannah River Site, and the commercial sector, SERA will improve the competitive position of companies that would otherwise have no access to those technologies. This Start-Up Plan details the steps SERA will take to begin effective operations by June 1, 1995, and will focus on the short-term needs of the program. This plan will serve as a supplement to the original SERA proposal, and will address the major milestones included in the Department of Energy`s Cooperative Agreement. Also documented are the planning processes that SERA will use to ensure the long-term viability of the program. The planning process will include additional work elements that are referenced by the original proposal, but, for the purposes of program start-up, are not immediately addressed. The major milestones and schedules are provided for each goal.

  17. Historical aspects of arising and features of activity of startup companies: accounting and economic aspects

    Directory of Open Access Journals (Sweden)

    S.F. Legenchuk

    2016-07-01

    Full Text Available The history of arising and development of the concept of «startup company» have been studied and the importance of their activities have been determined. Using the largest startups (Amazon, Google, Salesforce, VMware, Facebook, Twitter, Groupon, Zynga and Аpple the main components of their activity have been determined. Because of the lack of the scientific literature that directly investigated this topic the approaches of different authors from electronic sources have been systematized and the most used of them have been analyzed. The own vision of the definition of «startup company» and its key features have been formulated as a result of the research. The place of a startup company in the system of economic categories such as an economic activity, results of company activities, accounting, analysis and risks have been determined. The impact of the consequences of risks (positive and negative of economic activity on the future of companies have been considered. The value of accounting and analysis for the economic activity of startup companies have been evaluated.

  18. The Core Interaction of Platforms: How Startups Connect Users and Producers

    Directory of Open Access Journals (Sweden)

    Heidi M. E. Korhonen

    2017-09-01

    Full Text Available The platform economy is disrupting innovation while presenting both opportunities and challenges for startups. Platforms support value creation between multiple participant groups, and this operationalization of an ecosystem’s value co-creation represents the “core interaction” of a platform. This article focuses on that core interaction and studies how startups connect producers and users in value-creating core interaction through digital platforms. The study is based on an analysis of 29 cases of platform startups interviewed at a leading European startup event. The studied startups were envisioning even millions of users and hundreds or thousands of producers co-creating value on their platforms. In such platform businesses, our results highlight the importance of attracting a large user pool, providing novel services to those users, offering a new market for producers, supporting the core interaction in various ways, and utilizing elements of the platform canvas – an adaptation of the business model canvas, which we have accommodated for platform-based business models – to accomplish these goals.

  19. Start-up of an anaerobic fluidized bed reactor treating synthetic carbohydrate rich wastewater.

    Science.gov (United States)

    Yeshanew, Martha M; Frunzo, Luigi; Luongo, Vincenzo; Pirozzi, Francesco; Lens, Piet N L; Esposito, Giovanni

    2016-12-15

    The present work studied the start-up process of a mesophilic (37 ± 2 °C) anaerobic fluidized bed reactor (AFBR) operated at a hydraulic retention time (HRT) of 20 days using synthetic carbohydrate rich wastewater. Anox Kaldness-K1 carriers were used as biofilm carrier material. The reactor performance and biofilm formation were evaluated during the process. The start-up process at lower liquid recirculation flow rate enhanced the biofilm formation and reactor performance. The organic substrate composition had a major impact on early colonization of methanogenic archaea onto the surface of the Kaldness carriers during the start-up process. Specific organic substrates favouring the growth of methanogenic archaea, such as acetate, are preferred in order to facilitate the subsequent biofilm formation and AFBR start-up. The supply of 'bio-available' nutrients and trace elements, in particular iron, had an important role on optimal methanogenic activity and speeding-up of the biofilm development on the Kaldness carriers. This paper provides possible strategies to optimize the various operational parameters that influence the initial biofilm formation and development in an AFBR and similar high rate anaerobic reactors, hence can be used to reduce the long time required for process start-up. Copyright © 2016 Elsevier Ltd. All rights reserved.

  20. Preliminary investigation of flow dynamics during the start-up of a bulb turbine model

    Science.gov (United States)

    Coulaud, M.; Fraser, R.; Lemay, J.; Duquesne, P.; Aeschlimann, V.; Deschênes, C.

    2016-11-01

    Nowadays, the electricity network undergoes more perturbations due to the market demand. Additionally, an increase of the production from alternative resources such as wind or solar also induces important variations on the grid. Hydraulic power plants are used to respond quickly to these variations to stabilize the network. Hydraulic turbines have to face more frequent start-up and stop sequences that might shorten significantly their life time. In this context, an experimental analysis of start-up sequences has been conducted on the bulb turbine model of the BulbT project at the Hydraulic Machines Laboratory (LAMH) of Laval University. Maintaining a constant head, guide vanes are opened from 0 ° to 30 °. Three guide vanes opening speed have been chosen from 5 °/s to 20 °/s. Several repetitions were done for each guide vanes opening speed. During these sequences, synchronous time resolved measurements have been performed. Pressure signals were recorded at the runner inlet and outlet and along the draft tube. Also, 25 pressure measurements and strain measurements were obtained on the runner blades. Time resolved particle image velocimetry were used to evaluate flowrate during start-up for some repetitions. Torque fluctuations at shaft were also monitored. This paper presents the experimental set-up and start-up conditions chosen to simulate a prototype start-up. Transient flowrate methodology is explained and validation measurements are detailed. The preliminary results of global performances and runner pressure measurements are presented.

  1. Organising a conference? Think about what you can do for start-ups!

    CERN Multimedia

    David Mazur

    2016-01-01

    ICTR-PHE 2016 welcomed 16 exhibitors and sponsors as part of its industrial exhibition. If you have ever (co-)organised a large scientific conference, you almost certainly have your own list of major industrial actors who could be interested in becoming exhibitors or sponsors.   The six start-ups present at ICTR-PHE 2016 – Oncoradiomics, Colnec Health, Dixit Solutions, e-Learning4Health, I-See Computing and SmART Scientific Solutions (not pictured). (Image: Salvatore Fiore) ICTR-PHE has shown that scientific conferences can have a catalysing role in transforming young start-ups and spin-off companies into the key industrial players of tomorrow. A special start-up corner was provided in the industrial exhibition, where small stands were made available for a modest fee to start-ups and spin-off companies in fields relevant to the conference theme, together with a 5-minute timeslot for a pitch to the audience. Six start-ups, from the Netherlands, Italy and France...

  2. Ophthalmic Start-Up Chief Executive Officers' Perceptions of Development Hurdles.

    Science.gov (United States)

    Stewart, William C; Nelson, Lindsay A; Kruft, Bonnie; Stewart, Jeanette A

    2017-08-26

    To identify current challenges facing ophthalmic pharmaceutical start-ups in developing new products. Surveys were distributed to the chief executive officer (CEO) or president of ophthalmic start-ups. The survey attracted 24 responses from 78 surveys distributed (31%). The CEOs stated that a lack of financial capital (n = 18, 75%), FDA regulations (n = 6, 25%), and failure to meet clinical endpoints (n = 6, 25%) were their greatest development hurdles. Risk aversion to medicines in early development (n = 18, 75%), mergers and acquisitions reducing corporate choice for licensing agreements (n = 7, 29%), the emergence of large pharmaceutical-based venture capital funding groups (n = 12, 50%), and the failure of many large pharmaceutical companies to develop their own medicines (n = 10, 42%) were noted as recent prominent trends affecting fundraising. The study suggests that development funding, regulatory burden, and meeting clinical endpoints are the greatest development challenges faced by ophthalmic start-up CEOs. © 2017 S. Karger AG, Basel.

  3. Assessment of Startup Fuel Options for the GNEP Advanced Burner Reactor (ABR)

    Energy Technology Data Exchange (ETDEWEB)

    Jon Carmack (062056); Kemal O. Pasamehmetoglu (103171); David Alberstein

    2008-02-01

    The Global Nuclear Energy Program (GNEP) includes a program element for the development and construction of an advanced sodium cooled fast reactor to demonstrate the burning (transmutation) of significant quantities of minor actinides obtained from a separations process and fabricated into a transuranic bearing fuel assembly. To demonstrate and qualify transuranic (TRU) fuel in a fast reactor, an Advanced Burner Reactor (ABR) prototype is needed. The ABR would necessarily be started up using conventional metal alloy or oxide (U or U, Pu) fuel. Startup fuel is needed for the ABR for the first 2 to 4 core loads of fuel in the ABR. Following start up, a series of advanced TRU bearing fuel assemblies will be irradiated in qualification lead test assemblies in the ABR. There are multiple options for this startup fuel. This report provides a description of the possible startup fuel options as well as possible fabrication alternatives available to the program in the current domestic and international facilities and infrastructure.

  4. A simple and effective method to achieve the successful start-up of a current reference

    Institute of Scientific and Technical Information of China (English)

    Han Lei; Wang Yujun; Zhang Xiaoxing; DaiYujie; Lü Yingjie

    2012-01-01

    Start-up design is a critical issue in current reference as it is very closely related to production yield.However,its function is difficult to predict using normal transaction simulations before the device is put into diffusion.In this paper,we discuss a simple and effective simulation approach which ensures a successful start-up process in a self-biased temperature independent current reference.The circuit is implemented in a class-D power amplifier with a 0.35 μm BiCMOS process and the experimental result validates that,by using this method,the start-up success rate can be greatly improved to 100%.

  5. Missing links between lean startup, design thinking, and experiential learning approaches in entrepreneurship education

    DEFF Research Database (Denmark)

    Ramsgaard, Michael Breum; Christensen, Marie Ernst

    2016-01-01

    , design thinking, and experiential learning be identified? • How can new concepts of learning models, taking lean startup, design thinking and experiential learning approaches into account, be developed in entrepreneurship education? Approach This 3e conference paper begins as a conceptual paper...... highlighting the theories and underlying learning models behind three pedagogical approaches within entrepreneurship education, namely lean startup, design thinking and experiential learning. The paper builds this knowledge framework in order to set the design for an empirical investigation of the proposed...... valuable for research in entrepreneurship education. In-depth interviews will provide data to be analyzed in combination with vignette methods that seeks to test the following research question: How do entrepreneurship educators reflect upon the three approaches lean startup, design thinking...

  6. The Impact of Institutional Settings on Learning Behavior by Venture Capitalists and Start-Ups

    DEFF Research Database (Denmark)

    Gatti, Anna; Vendelø, Morten Thanning

    2005-01-01

    capitalists represent an institutionalized type of organization with formalized rules and standards, codified be-havior and roles (Suchman, 1995; Suchman et al., 2001). European venture capitalists and start-ups may imitate behavior and rules developed in Silicon Valley, and thus, a second research objective...... differen-ces in local institutional settings affect learning and adaptation by European venture ca-pitalists and start-ups, and thus, affect the processes of field formation. For example, it has been observed that institutional settings can facilitate or discourage learning from direct experience (Herriot...... et al., 1985). Thus, depending on the institutional settings venture capitalists and start-ups may rely on diffusion of experience in various degrees. Experiences can diffuse from the US, where venture capitalism as an entrepreneurial form evolved in Silicon Valley in the 1970s. In the US venture...

  7. The value of business incubation services for early stage start-ups

    DEFF Research Database (Denmark)

    Jakobsen, Brian; Tanev, Stoyan; Jensen, Søren

    2017-01-01

    that they could create value for the different stakeholders involved in their business ecosystem. The second issue is the need to categorize the various types of business incubators before examining the way they create value for early start-ups. In most national or regional entrepreneurial ecosystems...... there are different types of business incubators that do not necessarily offer the same types of services neither share a common vision about the way they should create value for their client companies. At the same time, early stage start-ups rely on the services provided by incubators and accelerators and need...... of the benefits from engaging in specific incubation programs. The objective of this paper is to investigate the value dimensions of specific types of business incubation services for early-stage start-ups in a way that may help such newly created firms to maximize the benefits from their participation...

  8. An analysis of reactivity prediction during the reactor start-up process

    Energy Technology Data Exchange (ETDEWEB)

    Bajgl, Josef [CEZ a.s., Dukovany (Czech Republic); Krysl, Vaclav; Svarny, Jiri [SKODA JS a.s., Plzen (Czech Republic)

    2015-09-15

    The different VVER-440 core fuel loadings subcriticality evaluations are performed during the start-up process by boron dilution or control assembly withdrawn by macrocode MOBY-DICK calculations. The dynamic reactivity and quasicritical reactivity are compared and sensitivity of reactivity prediction at the low boundary of start-up interval (ρ = -0,01) has been provided on the basis of different modelling of ionization chamber (IC) response calculation. Special attention is paid to the impact of power distribution and spontaneous fission distribution form factor on IC response correction during control assembly movement. Precision and robustness of different corrections of IC signal processing in real core start-up processed IC signals was evaluated.

  9. ZERO WASTE

    OpenAIRE

    Upadhyaya, Luv

    2013-01-01

    The aim of the thesis was to develop a clear vision on better waste management system. The thesis introduced the sustainable waste management along with innovation. The aim of the research was to find out the types of waste being introduced to environment, their consequence on human beings and surroundings, best policies, principles and practices to minimize the effect of the waste to lowest. The study was based on literature. The thesis includes the introduction of types of waste, clarifi...

  10. The start-up analysis of a PEM fuel cell system in vehicles

    DEFF Research Database (Denmark)

    Rabbani, Raja Abid; Rokni, Masoud; Hosseinzadeh, Elham;

    2014-01-01

    results for start-up scenario are presented. It is shown that system stability is influenced by slow thermal management controls. High loads at start-up affect voltage and system efficiency adversely. Cathode inlet water levels are found to be adequate for humidification of recirculated fuel stream......Addressing large load fluctuation in automotive applications, dynamic analysis of a polymer electrolyte membrane fuel cell system is conducted here. Operations of a comprehensive system-level control-oriented fuel cell model with all necessary auxiliary components are demonstrated and simulation...

  11. The Impact of Institutional Settings on Learning Behavior by Venture Capitalists and Start-Ups

    DEFF Research Database (Denmark)

    Gatti, Anna; Vendelø, Morten Thanning

    2005-01-01

    capitalists represent an institutionalized type of organization with formalized rules and standards, codified be-havior and roles (Suchman, 1995; Suchman et al., 2001). European venture capitalists and start-ups may imitate behavior and rules developed in Silicon Valley, and thus, a second research objective...... et al., 1985). Thus, depending on the institutional settings venture capitalists and start-ups may rely on diffusion of experience in various degrees. Experiences can diffuse from the US, where venture capitalism as an entrepreneurial form evolved in Silicon Valley in the 1970s. In the US venture...

  12. Start-up conditions and the performance of women - and men - controlled businesses in manufacturing industries

    Directory of Open Access Journals (Sweden)

    Otilia Driga

    2010-01-01

    Full Text Available Recent research into the economic performance of women-controlled firms suggests that their underperformance may not be the result of differences in the managerial ability of women as compared to men, and that it may in fact be a consequence of differing levels of start-up resources. Using accounting data, we examine the effects that selected start-up conditions have had on the observed economic performance of a sample of 4450 Spanish manufacturing firms. The results, which indicate significant differences in the initial conditions and show lower levels of assets and employee numbers in women-controlled firms, have implications for the economic performance of such firms.

  13. 1993 baseline solid waste management system description

    Energy Technology Data Exchange (ETDEWEB)

    Armacost, L.L.; Fowler, R.A.; Konynenbelt, H.S.

    1994-02-01

    Pacific Northwest Laboratory has prepared this report under the direction of Westinghouse Hanford Company. The report provides an integrated description of the system planned for managing Hanford`s solid low-level waste, low-level mixed waste, transuranic waste, and transuranic mixed waste. The primary purpose of this document is to illustrate a collective view of the key functions planned at the Hanford Site to handle existing waste inventories, as well as solid wastes that will be generated in the future. By viewing this system as a whole rather than as individual projects, key facility interactions and requirements are identified and a better understanding of the overall system may be gained. The system is described so as to form a basis for modeling the system at various levels of detail. Model results provide insight into issues such as facility capacity requirements, alternative system operating strategies, and impacts of system changes (ie., startup dates). This description of the planned Hanford solid waste processing system: defines a baseline system configuration; identifies the entering waste streams to be managed within the system; identifies basic system functions and waste flows; and highlights system constraints. This system description will evolve and be revised as issues are resolved, planning decisions are made, additional data are collected, and assumptions are tested and changed. Out of necessity, this document will also be revised and updated so that a documented system description, which reflects current system planning, is always available for use by engineers and managers. It does not provide any results generated from the many alternatives that will be modeled in the course of analyzing solid waste disposal options; such results will be provided in separate documents.

  14. Trademark or patent? The effects of market structure, customer type and venture capital financing on start-ups' IP decisions

    NARCIS (Netherlands)

    A.G.B. de Vries (Geertjan); H.P.G. Pennings (Enrico); J.H. Block (Jörn)

    2013-01-01

    textabstractWe analyze the initial intellectual property (IP) right of 4,703 start-up entrants in the US, distinguishing between trademark and patent applications. The results show that start-ups are more likely to file for a trademark instead of a patent when entering into more competitive market s

  15. Trademark or patent? The effects of market structure, customer type and venture capital financing on start-ups' IP decisions

    NARCIS (Netherlands)

    A.G.B. de Vries (Geertjan); H.P.G. Pennings (Enrico); J.H. Block (Jörn)

    2013-01-01

    textabstractWe analyze the initial intellectual property (IP) right of 4,703 start-up entrants in the US, distinguishing between trademark and patent applications. The results show that start-ups are more likely to file for a trademark instead of a patent when entering into more competitive market

  16. Summary of radioactive solid waste received in the 200 areas during calendar year 1996

    Energy Technology Data Exchange (ETDEWEB)

    Hladek, K.L.

    1997-05-21

    Rust Federal Services of Hanford Inc. manages and operates the Hanford Site 200 Area radioactive solid waste storage and disposal facilities for the US Department of Energy, Richland Operations Office under contract DE-AC06-87RL10930. These facilities include storage areas and disposal sites for radioactive solid waste. This document summarizes the amount of radioactive materials that have been buried and stored in the 200 Area radioactive solid waste storage and disposal facilities from startup in 1944 through calendar year 1996. This report does not include backlog waste, solid radioactive wastes in storage or disposed of in other areas, or facilities such as the underground tank farms. Unless packaged within the scope of WHC-EP-0063, Hanford Site Solid Waste Acceptance Criteria, liquid waste data are not included in this document.

  17. Summary of radioactive solid waste received in the 200 areas during calendar year 1996

    Energy Technology Data Exchange (ETDEWEB)

    Hladek, K.L.

    1997-05-21

    Rust Federal Services of Hanford Inc. manages and operates the Hanford Site 200 Area radioactive solid waste storage and disposal facilities for the US Department of Energy, Richland Operations Office under contract DE-AC06-87RL10930. These facilities include storage areas and disposal sites for radioactive solid waste. This document summarizes the amount of radioactive materials that have been buried and stored in the 200 Area radioactive solid waste storage and disposal facilities from startup in 1944 through calendar year 1996. This report does not include backlog waste, solid radioactive wastes in storage or disposed of in other areas, or facilities such as the underground tank farms. Unless packaged within the scope of WHC-EP-0063, Hanford Site Solid Waste Acceptance Criteria, liquid waste data are not included in this document.

  18. Commercial SNF Accident Release Fractions

    Energy Technology Data Exchange (ETDEWEB)

    J. Schulz

    2004-11-05

    The purpose of this analysis is to specify and document the total and respirable fractions for radioactive materials that could be potentially released from an accident at the repository involving commercial spent nuclear fuel (SNF) in a dry environment. The total and respirable release fractions are used to support the preclosure licensing basis for the repository. The total release fraction is defined as the fraction of total commercial SNF assembly inventory, typically expressed as an activity inventory (e.g., curies), of a given radionuclide that is released to the environment from a waste form. Radionuclides are released from the inside of breached fuel rods (or pins) and from the detachment of radioactive material (crud) from the outside surfaces of fuel rods and other components of fuel assemblies. The total release fraction accounts for several mechanisms that tend to retain, retard, or diminish the amount of radionuclides that are available for transport to dose receptors or otherwise can be shown to reduce exposure of receptors to radiological releases. The total release fraction includes a fraction of airborne material that is respirable and could result in inhalation doses; this subset of the total release fraction is referred to as the respirable release fraction. Accidents may involve waste forms characterized as: (1) bare unconfined intact fuel assemblies, (2) confined intact fuel assemblies, or (3) canistered failed commercial SNF. Confined intact commercial SNF assemblies at the repository are contained in shipping casks, canisters, or waste packages. Four categories of failed commercial SNF are identified: (1) mechanically and cladding-penetration damaged commercial SNF, (2) consolidated/reconstituted assemblies, (3) fuel rods, pieces, and debris, and (4) nonfuel components. It is assumed that failed commercial SNF is placed into waste packages with a mesh screen at each end (CRWMS M&O 1999). In contrast to bare unconfined fuel assemblies, the

  19. Secondary Waste Cementitious Waste Form Data Package for the Integrated Disposal Facility Performance Assessment

    Energy Technology Data Exchange (ETDEWEB)

    Cantrell, Kirk J. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Westsik, Joseph H. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Serne, R Jeffrey [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Um, Wooyong [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Cozzi, Alex D. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

    2016-05-16

    A review of the most up-to-date and relevant data currently available was conducted to develop a set of recommended values for use in the Integrated Disposal Facility (IDF) performance assessment (PA) to model contaminant release from a cementitious waste form for aqueous wastes treated at the Hanford Effluent Treatment Facility (ETF). This data package relies primarily upon recent data collected on Cast Stone formulations fabricated with simulants of low-activity waste (LAW) and liquid secondary wastes expected to be produced at Hanford. These data were supplemented, when necessary, with data developed for saltstone (a similar grout waste form used at the Savannah River Site). Work is currently underway to collect data on cementitious waste forms that are similar to Cast Stone and saltstone but are tailored to the characteristics of ETF-treated liquid secondary wastes. Recommended values for key parameters to conduct PA modeling of contaminant release from ETF-treated liquid waste are provided.

  20. Office of Waste Isolation. Progress report, November 1977. [National waste terminal storage

    Energy Technology Data Exchange (ETDEWEB)

    Rhines, R.C.; Asher, J.M. (eds.)

    1977-12-28

    This program is part of the National Waste Terminal Storage program. The Geologic Review Group meeting was held in New Orleans, November 16-17. Start-up of the near-surface heater experiment in the Conasauga Shale formation is under way at Oak Ridge. The first shipment of experimental equipment from Oak Ridge to Avery Island, Louisiana, for the dome salt in-situ test was successfully completed. On November 9-10, a design status review on the spent fuel repository conceptual design was held with Kaiser Engineers, Inc. On November 2, OWI personnel reviewed the progress on the Economic Studies with TRW representatives.

  1. Numerical Simulation of Non-Inductive Startup of the Pegasus Toroidal Experiment

    Science.gov (United States)

    O'Bryan, John B.

    The dynamics and relaxation of magnetic flux ropes produced during non-inductive startup of the Pegasus Toroidal Experiment are simulated with nonlinear magnetohydrodynamic and two-fluid plasma models. A current filament is produced by a single injector and directed along multiple passes by toroidal and vertical vacuum magnetic field components. Adjacent passes of the current filament merge and reconnect, releasing an axisymmetric current ring from the driven channel. Squashing degree analysis indicates the presence of a quasi-separatrix layer (QSL) during ring formation, but the QSL does not solely correspond to magnetic reconnection. Chaotic scattering is also apparent from the distribution of magnetic field-line lengths. The merging of adjacent passes constitutes coherent dynamo action that affects the toroidally-averaged magnetic-field distribution. The MHD dynamo--primarily from the vertical displacement of the current channel--concentrates symmetric poloidal flux and transfers significant energy to the forming flux-rope ring. Accumulation of poloidal flux over many reconnection events contributes to the development of a poloidal magnetic field null near the central column that redirects the driven current filament, such that its path traces a toroidal surface. After cessation of the simulated current drive, temperature and current profiles broaden and closed flux surfaces form rapidly and encompass a large plasma volume. High toroidal-mode number harmonics of the magnetic energy decay preferentially, leaving a tokamak-like plasma suitable for transition to other forms of current drive. Computations with the two-fluid terms in Ohm's Law produce qualitatively similar plasma evolution to the MHD computations. However, for the computations with the two-fluid plasma model, the ion fluid significantly decouples from the electron fluid, weakening the dynamics during magnetic reconnection. This effect is quantified by comparing global and local plasma parameters in

  2. Project Startup: Evaluating the Performance of Hydraulic Hybrid Refuse Vehicles

    Energy Technology Data Exchange (ETDEWEB)

    2015-09-01

    The Fleet Test and Evaluation Team at the National Renewable Energy Laboratory (NREL) is evaluating the in-service performance of 10 next-generation hydraulic hybrid refuse vehicles (HHVs), 8 previous-generation HHVs, and 8 comparable conventional diesel vehicles operated by Miami-Dade County's Public Works and Waste Management Department in southern Florida. The HHVs under study - Autocar E3 refuse trucks equipped with Parker Hannifin's RunWise Advanced Series Hybrid Drive systems - can recover as much as 70 percent of the energy typically lost during braking and reuse it to power the vehicle. NREL's evaluation will assess the performance of this technology in commercial operation and help Miami-Dade County determine the ideal routes for maximizing the fuel-saving potential of its HHVs.

  3. Generation and release of radioactive gases in LLW disposal facilities

    Energy Technology Data Exchange (ETDEWEB)

    Yim, M.S. [Harvard School Public Health, Boston, MA (United States); Simonson, S.A. [Massachusetts Institute of Technology, Cambridge, MA (United States)

    1995-02-01

    The atmospheric release of radioactive gases from a generic engineered LLW disposal facility and its radiological impacts were examined. To quantify the generation of radioactive gases, detailed characterization of source inventory for carbon-14, tritium, iodine-129, krypton-85, and radon-222, was performed in terms of their activity concentrations; their distribution within different waste classes, waste forms and containers; and their subsequent availability for release in volatile or gaseous form. The generation of gases was investigated for the processes of microbial activity, radiolysis, and corrosion of waste containers and metallic components in wastes. The release of radionuclides within these gases to the atmosphere was analyzed under the influence of atmospheric pressure changes.

  4. The Influence of Innovation and Entrepreneurial Self-Efficacy to Digital Startup Success

    Directory of Open Access Journals (Sweden)

    Agnes Dessyana

    2017-08-01

    Full Text Available Establishing and developing a startup business is not easy. Startup success depend on various aspects, such as financial,business model, and learning organizations. Personalities factor of founders have a contribution in business development, especially entrepreneurial self-efficacy (ESE and innovation. But, in Indonesia, there is still no psychological study who see the contribution of those factors on business success in digital startup. This study aimed to understand how both factors influence startup digital. The sample is 64 founders. The research instrument is ESE, KAI, and Business Success questionnaire (Kirton in Riyanti, 2003; Chen et al, 1998; Kaplan & Norton, 2006. Multiple-regression analyses reveal ESE and innovation contributes 20.8% to business success. ESE regression coefficient is 0.200 (P 0.05. This means, ESE has significant positive effect, while innovation has a positive relationship but insignificant. Interventions in the form of booklets that inform how to increase ESE. The booklet is already conducted trials on five founders.

  5. Barriers to Start-Up and Their Effect on Aspirant Entrepreneurs

    Science.gov (United States)

    Robertson, Martyn; Collins, Amanda; Medeira, Natasha; Slater, James

    2003-01-01

    The importance of new business start-ups cannot be over-emphasised. The UK government has taken actions designed to stimulate the growth of new businesses and aid their survival. The identification of barriers to entry is important, together with strategies to minimise their impact. The UK continues to lag behind the USA in its levels of…

  6. The Impact of Start-up Grants on Firm Performance in Estonia

    Directory of Open Access Journals (Sweden)

    Siret Vildo

    2013-01-01

    Full Text Available As in economic theory start-up enterprises have been seen as important sources of growth, the government support measures to enterprises have been a common practice around the world for decades. As the governmental support to enterprises is often of a considerable amount of money there is a need to assess its efficiency. In the present article we study the impact of Estonian start-up grants distributed in 2002 and 2003 on various indicators of firm performance with econometric methods, namely propensity score matching. We use the data from the Estonian Business Register in order to study the impact of start-up grants on various economic indicators like the number of employees, turnover, equity, fixed assets and firm survival. The results showed that the start-up grants proved to affect positively the number of employed people and turnover, yet the impact on productivity was negative. One implication of the study is that it is difficult to achieve different goals to the same extent with a single governmental grant

  7. LightCDD: a lightweight capability-driven development method for start-ups

    NARCIS (Netherlands)

    Koç, Hasan; Ruiz Carmona, L.M.; Espana Cubillo, S.

    2016-01-01

    Novice innovators and entrepreneurs face the risk of designing naive business models. In fact, lack of realism and failing to envision contextual constraints is one of the main threats to start-up success. Both the literature and the responses we gathered from experts in incubation confirm this prob

  8. Experimental Labs for Start-Ups: The Role of the "Venture-Sitter"

    Science.gov (United States)

    Matricano, Diego; Pietrobon, Alberto

    2010-01-01

    Curley and Formica's (2008, 2010) studies of high-expectation entrepreneurship focus on the role of "experimental laboratories" in promoting the start-up and successful development of high-expectation firms. Although it is not difficult to understand the potential usefulness of these experimental labs--business simulators in which skilled partners…

  9. Social and Environmental Considerations within the IT Sector: Evidence from Romanian Start-Ups

    Directory of Open Access Journals (Sweden)

    Irina-Eugenia Iamandi

    2016-12-01

    Full Text Available The research purpose of the present paper is to investigate the nature and depth of integrating social and environmental requirements into daily economic activities of Romanian start-ups from technology and Internet-related business sectors. As such, more than 150 already launched start-ups in Romania were analysed according to their economic, social and environmental scopes, on a scale quantifying their involvement degree. The results emphasize that, although economically-driven in most of the cases, the technology and Internet-related start-ups in Romania are increasingly considering the social and environmental concerns. This finding refers to the strategic inclusion of the sustainability requirements in their object of activity and inner core of their business, and not to mere corporate social responsibility (CSR pursuits. The conclusion emphasizes a new business pattern implemented by Romanian start-ups in the technology, information and Internet-related domains, where economic, social and environmental requirements are considered together when the corporate business strategy is formulated on the long run.

  10. Start-up problem with an induction machine and a permanent magnet gear

    DEFF Research Database (Denmark)

    Frandsen, Tommy; Berg, Nick Ilsø; Holm, Rasmus Koldborg;

    2014-01-01

    This paper presents the preliminary work conducted to design a magnetic gear (MG) integrated with a fan and driven by an grid connected induction machine (IM). A start-up problem with a MG, which occurs due to a high oscillating torque and a high breakdown torque of the IM when starting up directly...

  11. Improving startup performance with carbon mesh anodes in separator electrode assembly microbial fuel cells

    KAUST Repository

    Zhang, Fang

    2013-04-01

    In a separator electrode assembly microbial fuel cell, oxygen crossover from the cathode inhibits current generation by exoelectrogenic bacteria, resulting in poor reactor startup and performance. To determine the best approach for improving startup performance, the effect of acclimation to a low set potential (-0.2V, versus standard hydrogen electrode) was compared to startup at a higher potential (+0.2V) or no set potential, and inoculation with wastewater or pre-acclimated cultures. Anodes acclimated to -0.2V produced the highest power of 1330±60mWm-2 for these different anode conditions, but unacclimated wastewater inocula produced inconsistent results despite the use of this set potential. By inoculating reactors with transferred cell suspensions, however, startup time was reduced and high power was consistently produced. These results show that pre-acclimation at -0.2V consistently improves power production compared to use of a more positive potential or the lack of a set potential. © 2013 Elsevier Ltd.

  12. NSFC Supported CERN LHC Accomplished Start-up in September,2008

    Institute of Scientific and Technical Information of China (English)

    Zhang Yongtao

    2008-01-01

    @@ After 15 years of construction,the Large Hadron Collider (LHC),the world's largest and highest-energy particle accelerator accomplished its start-up on September 10,2008.Scientists predict that this historical event will be a milestone on physics research.

  13. 78 FR 40757 - Prospective Grant of Start-Up Exclusive Commercialization License: The Development of a...

    Science.gov (United States)

    2013-07-08

    ... Circularly Permuted Chimeric Molecules'' ; (b) Technology family E-021-2010/0, including U.S. Patent... related continuing and foreign patents/patent applications for these technology families, to Medicenna... start-up exclusive commercialization license to practice the inventions embodied in: (a)...

  14. Impedance estimation of photovoltaic modules for inverter start-up analysis

    Indian Academy of Sciences (India)

    PALLAVI BHARADWAJ; ABHIJIT KULKARNI; VINOD JOHN

    2017-08-01

    Starting-up of photovoltaic (PV) inverters involves pre-charging of the input dc bus capacitance. Ideally, direct pre-charging of this capacitance from the PV modules is possible as the PV modules are current limited. Practically, the parasitic elements of the system such as the PV module capacitance, effective wire inductance and resistance determine the start-up transient. The start-up transient is also affected by the contactor connecting the PV modules to the inverter input dc bus. In this work, the start-up current and voltages are measured experimentally for different parallel and series connections of the PV modules. These measurements are used to estimate the stray elements, namely the PV module capacitance, effective inductance and resistance.The estimation is based on a linear small-signal model of the start-up conditions. The effect of different connections of the PV modules and the effect of varying irradiation on the scaling of the values of the stray elements are quantified. The System model is further refined by inclusion of connecting cable capacitance and contactor resistance. Dynamics of the resulting fifth-order model are seen to be consistent with those of the simplified third-order model. The analysis of this paper can be used to estimate the expected peak inrush current in PV inverters. It can also be used to arrive at a detailed modelling of PV modules to evaluate the transient behaviour.

  15. 75 FR 26892 - Approval and Promulgation of Implementation Plans; Texas; Excess Emissions During Startup...

    Science.gov (United States)

    2010-05-13

    ... Administrator for Air, Noise, and Radiation, entitled ``Policy on Excess Emissions During Startup, Shutdown... February 15, 1983, from Kathleen M. Bennett, Assistant Administrator for Air, Noise, and Radiation (1983... based on health or safety risks subject to Executive Order 13045 (62 FR 19885, April 23, 1997); Is not...

  16. Ed Tech Developer's Guide: A Primer for Software Developers, Startups, and Entrepreneurs

    Science.gov (United States)

    Bienkowski, Marie; Gerard, Sarah Nixon; Rubin, Shawn; Sanford, Cathy; Borrelli-Murray, Dana; Driscoll, Tom; Arora, Jessie; Hruska, Mike; Beck, Katie; Murray, Thomas; Hoekstra, Jason; Gannes, Stuart; Metz, Edward; Midgley, Steve; Castilla, Stephanie; Tomassini, Jason; Madda, Mary Jo; Chase, Zac; Martin, Erik; Noel, Marcus; Styles, Kathleen

    2015-01-01

    Opportunities abound for software designers and developers to create impactful tools for teachers, school leaders, students, and their families. This guide for developers, startups, and entrepreneurs addresses key questions about the education ecosystem and highlights critical needs and opportunities to develop digital tools and apps for learning.…

  17. Active vibration control of multibody system with quick startup and brake based on active damping

    Institute of Scientific and Technical Information of China (English)

    TANG Hua-ping; TANG Yun-jun; TAO Gong-an

    2006-01-01

    A kind of active vibration control method was presented based on active damping and optimization design for driving load of multibody system with quick startup and brake. Dynamical equation of multibody system with quick startup and brake and piezoelectric actuators intelligent structure was built. The optimum driving load was calculated by applying the presented method. The self-sensing and self-tuning closed-loop active vibration control in quick startup and brake process was realized. The control algorithm, using local velocity negative feedback, i.e. the output of a sensor only affects the output of the actuator collocated, can induce damping effectively to actively suppress the system vibration. Based on the optimization design for driving load of multibody system with quick startup and bake, the active damping of piezoelectric actuators intelligent structure was used to farther suppress the vibration of system. Theoretical analysis and calculation of numerical show that the proposed method makes the vibration of system decrease more than the optimal design method for driving load of multibody system.

  18. Ideology as resource in entrepreneurial journalism: The French online news startup Mediapart

    NARCIS (Netherlands)

    Wagemans, A.; Witschge, T.; Deuze, M.

    2016-01-01

    The emergence of a startup culture in the field of journalism is global: since the early years of the twenty-first century, new independent journalism companies have formed around the world. Although setting up one’s own journalistic practice is not particularly novel in the news industry, the last

  19. Ideology as Resource in Entrepreneurial Journalism : The French online news startup Mediapart

    NARCIS (Netherlands)

    Wagemans, Andrea; Witschge, Tamara; Deuze, Mark

    2016-01-01

    The emergence of a startup culture in the field of journalism is global: since the early years of the twenty-first century, new independent journalism companies have formed around the world. Although setting up one's own journalistic practice is not particularly novel in the news industry, the last

  20. Harvesting the results of the mentoring process of knowledge intensive startups

    NARCIS (Netherlands)

    Weijman, Geertjan; van der Sijde, Peter; van Benthem, Jann W.L.

    2008-01-01

    Mentoring is often used by business development programs to assist startups. In this paper we look at the perceptions of protégés and mentors about this process, hereby different business development programs in Europe were incorporated. It was hypothesized that there is a relationship between

  1. Entrepreneurship Education: Enhancing or Discouraging Graduate Start-Up at the University of Pretoria

    Science.gov (United States)

    Botha, Melodi; Ras, Rochelle

    2016-01-01

    In-depth interviews were conducted with a sample of BCom Entrepreneurship graduates, as well as a control group to determine whether the exposure to entrepreneurship education can enhance actual business start-up. Information was collected on how they experienced the learning approaches, and the value which they had derived from the degree. This…

  2. The Impact of Domestic Drivers and Barriers on the Entrepreneurial Start-up Decision

    NARCIS (Netherlands)

    Lubberink, R.J.B.; Blok, V.; Ophem, van J.; Omta, S.W.F.

    2013-01-01

    This paper explores the impact of the family network on the start-up decision byidentifying domestic drivers and barriers to entrepreneurship. For this, we used anadjusted model of work-family conflict theory, with special attention to the family lifecycle stages. In order to identify the drivers an

  3. 40 CFR 63.310 - Requirements for startups, shutdowns, and malfunctions.

    Science.gov (United States)

    2010-07-01

    ... or operator shall operate and maintain the coke oven battery and its pollution control equipment required under this subpart, in a manner consistent with good air pollution control practices for... CATEGORIES National Emission Standards for Coke Oven Batteries § 63.310 Requirements for startups, shutdowns...

  4. Entrepreneurship Education: Enhancing or Discouraging Graduate Start-Up at the University of Pretoria

    Science.gov (United States)

    Botha, Melodi; Ras, Rochelle

    2016-01-01

    In-depth interviews were conducted with a sample of BCom Entrepreneurship graduates, as well as a control group to determine whether the exposure to entrepreneurship education can enhance actual business start-up. Information was collected on how they experienced the learning approaches, and the value which they had derived from the degree. This…

  5. Reactor operating procedures for startup of continuously-operated chemical plants

    NARCIS (Netherlands)

    Verwijs, J.W.; Kösters, P.H.; Berg, van den H.; Westerterp, K.R.

    1995-01-01

    Rules are presented for the startup of an adiabatic tubular reactor, based on a qualitative analysis of the dynamic behavior of continuously-operated vapor- and liquid-phase processes. The relationships between the process dynamics, operating criteria, and operating constraints are investigated, sin

  6. Yield Stress and Low-Temperature Start-Up Torque of Lubricating Greases

    NARCIS (Netherlands)

    Cyriac, F.; Lugt, Pieter Martin; Bosman, Rob

    2016-01-01

    A comprehensive study of the yield stress and start-up torque for six commonly used rolling bearing greases is presented. Both parameters were found to depend exponentially on temperature where the exponent changes below a low-temperature “break point.” This break point was found to be related to

  7. Network effects on Entrepreneurial Processes: Start-ups in the Dutch ICT Industry 1990-2000

    NARCIS (Netherlands)

    W. Hulsink (Wim); T. Elfring (Tom)

    2003-01-01

    textabstractThe value of networks as an integral part of the explanation of entrepreneurial success is widely acknowledged. It is unclear, however, in what way certain networks influence the success of start-up companies. The question of this paper is: 'in what way does the entrepreneur's network

  8. Unpainting the black box : exploring mechanisms and practices of start-up incubators

    NARCIS (Netherlands)

    van Weele, M.A.

    2016-01-01

    Although incubators have become one of the most prominent instruments to stimulate the emergence and growth of start-ups, questions are being raised about their effectiveness. One major obstacle to evaluate the effectiveness of incubators is that the incubator remains a ‘black box’: the extant liter

  9. Ideology as Resource in Entrepreneurial Journalism : The French online news startup Mediapart

    NARCIS (Netherlands)

    Wagemans, Andrea; Witschge, Tamara; Deuze, Mark

    2016-01-01

    The emergence of a startup culture in the field of journalism is global: since the early years of the twenty-first century, new independent journalism companies have formed around the world. Although setting up one's own journalistic practice is not particularly novel in the news industry, the last

  10. Nitrogen, phosphorus, calcium, and magnesium applied individually or as a slow release or controlled release fertilizer increase growth

    Science.gov (United States)

    The U.S. Environmental Protection Agency (USEPA) has restricted concentrated animal feeding operation(CAFO) release of waste products into U.S. waters. These waste products must be disposed of using best management practices. Most of the waste is spread on cropland, but some operations have found ot...

  11. Waste management

    DEFF Research Database (Denmark)

    2000-01-01

    The case study deals with public accountability issues connected to household waste management in the municipality of Copenhagen, Denmark.......The case study deals with public accountability issues connected to household waste management in the municipality of Copenhagen, Denmark....

  12. Waste management

    DEFF Research Database (Denmark)

    2000-01-01

    The case study deals with public accountability issues connected to household waste management in the municipality of Copenhagen, Denmark.......The case study deals with public accountability issues connected to household waste management in the municipality of Copenhagen, Denmark....

  13. Revolutionary advances in medical waste management. The Sanitec system.

    Science.gov (United States)

    Edlich, Richard F; Borel, Lise; Jensen, H Gordon; Winters, Kathryne L; Long, William B; Gubler, K Dean; Buschbacher, Ralph M; Becker, Daniel G; Chang, Dillon E; Korngold, Jonathan; Chitwood, W Randolph; Lin, Kant Y; Nichter, Larry S; Berenson, Susan; Britt, L D; Tafel, John A

    2006-01-01

    It is the purpose of this collective review to provide a detailed outline of a revolutionary medical waste disposal system that should be used in all medical centers in the world to prevent pollution of our planet from medical waste. The Sanitec medical waste disposal system consists of the following seven components: (1) an all-weather steel enclosure of the waste management system, allowing it to be used inside or outside of the hospital center; (2) an automatic mechanical lift-and-load system that protects the workers from devastating back injuries; (3) a sophisticated shredding system designed for medical waste; (4) a series of air filters including the High Efficiency Particulate Air (HEPA) filter; (5) microwave disinfection of the medical waste material; (6) a waste compactor or dumpster; and (7) an onboard microprocessor. It must be emphasized that this waste management system can be used either inside or outside the hospital. From start to finish, the Sanitec Microwave Disinfection system is designed to provide process and engineering controls that assure complete disinfection and destruction, while minimizing the operator's exposure to risk. There are numerous technologic benefits to the Sanitec systems, including environmental, operational, physical, and disinfection efficiency as well as waste residue disinfection. Wastes treated through the Sanitec system are thoroughly disinfected, unrecognizable, and reduced in volume by approximately 80% (saving valuable landfill space and reducing hauling requirements and costs). They are acceptable in any municipal solid waste program. Sanitec's Zero Pollution Advantage is augmented by a complete range of services, including installation, startup, testing, training, maintenance, and repair, over the life of this system. The Sanitec waste management system has essentially been designed to provide the best overall solution to the customer, when that customer actually looks at the total cost of dealing with the

  14. Storing Waste in Ceramic

    Energy Technology Data Exchange (ETDEWEB)

    Bourcier, W L; Sickafus, K

    2004-07-20

    Not all the nuclear waste destined for Yucca Mountain is in the form of spent fuel. Some of it will be radioactive waste generated from the production of nuclear weapons. This so-called defense waste exists mainly as corrosive liquids and sludge in underground tanks. An essential task of the U.S. high-level radioactive waste program is to process these defense wastes into a solid material--called a waste form. An ideal waste form would be extremely durable and unreactive with other repository materials. It would be simple to fabricate remotely so that it could be safely transported to a repository for permanent storage. What's more, the material should be able to tolerate exposure to intense radiation without degradation. And to minimize waste volume, the material must be able to contain high concentrations of radionuclides. The material most likely to be used for immobilization of radioactive waste is glass. Glasses are produced by rapid cooling of high-temperature liquids such that the liquid-like non-periodic structure is preserved at lower temperatures. This rapid cooling does not allow enough time for thermodynamically stable crystalline phases (mineral species) to form. In spite of their thermodynamic instability, glasses can persist for millions of years. An alternate to glass is a ceramic waste form--an assemblage of mineral-like crystalline solids that incorporate radionuclides into their structures. The crystalline phases are thermodynamically stable at the temperature of their synthesis; ceramics therefore tend to be more durable than glasses. Ceramic waste forms are fabricated at temperatures below their melting points and so avoid the danger of handling molten radioactive liquid--a danger that exists with incorporation of waste in glasses. The waste form provides a repository's first line of defense against release of radionuclides. It, along with the canister, is the barrier in the repository over which we have the most control. When a waste

  15. VSC-HVDC系统启动控制%Startup Procedures for the VSC-HVDC System

    Institute of Scientific and Technical Information of China (English)

    张静; 徐政; 陈海荣

    2009-01-01

    In order to reduce the undesired impacts and damages on the VSC-HVDC system and the connected AC system during the startup and re-startup procedures, appropriate startup control strategy should be dedicatedly designed. Charging the DC capacitor voltage to the preset value quickly is the fundamental of the subsequent control strategy. In this paper, a two-stage self startup procedure is proposed for VSC-HVDC system consisting of two-level and diode-clamped three-level converters. During the first stage, the resistors are inserted to limit the current during the charging. If the DC voltage can not reach the preset value after predetermined time, the startup procedure switches to the second stage and the capacitors will be further charged with a DC voltage controller. The startup procedure completes till the DC link voltage reaches the preset value and then the converters are ready to change from the startup mode to the normal operating mode. In addition, a new control strategy is proposed for the startup of the passive network and the AC system suffered from black out. With the proposed control strategy, the inrush currents during the energization of the transformers and the overvoltage during the closure of the long overhead transmission lines can be suppressed. Simulation results verify the feasibility of the proposed startup procedures.%合适的启动方式对减缓VSC-HVDC系统启动及重新启动时对自身和电网的冲击非常重要.如何把直流电容器电压快速提升到设定值,是后续控制策略正确工作的基础.针对目前应用较广泛的两电平和二极管钳位型三电平换流器拓扑结构,提出了一种简单、适用于VSC-HVDC系统的两阶段自励启动方法.在启动第一阶段,串接限流电阻器对直流侧电路充电;若在设定的时间内电容器电压不能达到设定值,启动转入第二阶段,即换流站在直流电压控制器的作用下对电容器继续充电,直至达到预设值,从而为换

  16. START-UP FINANCING SOURCES: DOES GENDER MATTER? SOME EVIDENCE FOR EU AND ROMANIA

    Directory of Open Access Journals (Sweden)

    Badulescu Alina

    2011-07-01

    Full Text Available Although financial resources are very important in SMEs in general, and for start-ups in particular, many entrepreneurs face numerous restrictions in finding sources for start-up financing. The present article aims to investigate the similarities or differences in start-up financing sources due to gender issues, otherwise to investigate if female entrepreneurs use (or have access different financial sources in the early stage of their business. As reported by the literature, access to finance is one of the most important issues for SMEs and nascent entrepreneurs. Moreover, among the main financial issues, the first one is the access to start-up finance (Schwartz, 1976; Carter and Cannon, 1992; Johnson and Storey, 1993; Koper, 1993; Van Auken et al, 1993; Carter and Rosa, 1998, FOBS survey 2005. In all sectors, women use for starting up businesses substantially less capital then men. Women encounter, more then men, credibility problems when dealing with bankers. This problem causes important effects concerning the performance, survival and growth of women-run businesses. The present research focuses on revealing how male and female entrepreneurs face and solve the problem of start-up financing sources. The methodology is based on using the dataset "Enterprises managed by the founder - broken down by gender of the entrepreneur", available in EUROSTAT database. The data selected refers to the start-up financing sources available for European Union and Romania, regarding activities included in NACE: Industry and services excluding public administration and management activities of holding companies and 2005 as time of reference. The data were used to make some comparison between: male versus female entrepreneurs in EU; male versus female entrepreneurs in Romania; EU entrepreneurs versus Romanian entrepreneurs. The main findings reveal that there are no significant differences between men and women concerning the start-up financing sources. The main

  17. Industrial Waste

    DEFF Research Database (Denmark)

    Christensen, Thomas Højlund

    2011-01-01

    of the system industry has to inform at the planning stage and afterwards in yearly reports on their waste arising and how the waste is managed. If available such information is very helpful in obtaining information about that specific industry. However, in many countries there is very little information......Industrial waste is waste from industrial production and manufacturing. Industry covers many industrial sectors and within each sector large variations are found in terms of which raw materials are used, which production technology is used and which products are produced. Available data on unit...... generation rates and material composition as well as determining factors are discussed in this chapter. Characterizing industrial waste is faced with the problem that often only a part of the waste is handled in the municipal waste system, where information is easily accessible. In addition part...

  18. AUDIT OF INNOVATIVE IDEAS AS THE PREVIOUS STAGE OF THE BUSINESS-PLAN OF START-UP PROJECTS

    Directory of Open Access Journals (Sweden)

    O. Zhylinska

    2014-09-01

    Full Text Available The phenomenon of feasibility reasoning of venture capital investment for the implementation of innovative ideas is revealed. The main elements of the methodology for feasibility of start-up projects, based on the concept of combination of life cycle of the market, product innovation and startup companies, are characterized. The comparative analysis of methods feasibility study and business plan start-up project is made, the importance of innovative ideas audit in future economic information generation and investment decisions of informal venture capital investors are shown.

  19. Testing cleanable/reuseable HEPA prefilters for mixed waste incinerator air pollution control systems

    Energy Technology Data Exchange (ETDEWEB)

    Burns, D.B.; Wong, A.; Walker, B.W.; Paul, J.D. [Westinghouse Savannah River Co., Aiken, SC (United States)

    1997-08-01

    The Consolidated Incineration Facility (CIF) at the US DOE Savannah River Site is undergoing preoperational testing. The CIF is designed to treat solid and liquid RCRA hazardous and mixed wastes from site operations and clean-up activities. The technologies selected for use in the air pollution control system (APCS) were based on reviews of existing incinerators, air pollution control experience, and recommendations from consultants. This approach resulted in a facility design using experience from other operating hazardous/radioactive incinerators. In order to study the CIF APCS prior to operation, a 1/10 scale pilot facility, the Offgas Components Test Facility (OCTF), was constructed and has been in operation since late 1994. Its mission is to demonstrate the design integrity of the CIF APCS and optimize equipment/instrument performance of the full scale production facility. Operation of the pilot facility has provided long-term performance data of integrated systems and critical facility components. This has reduced facility startup problems and helped ensure compliance with facility performance requirements. Technical support programs assist in assuring all stakeholders the CIF can properly treat combustible hazardous, mixed, and low-level radioactive wastes. High Efficiency Particulate Air (HEPA) filters are used to remove hazardous and radioactive particulates from the exhaust gas strewn before being released into the atmosphere. The HEPA filter change-out frequency has been a potential issue and was the first technical issue to be studied at the OCTF. Tests were conducted to evaluate the performance of HEPA filters under different operating conditions. These tests included evaluating the impact on HEPA life of scrubber operating parameters and the type of HEPA prefilter used. This pilot-scale testing demonstrated satisfactory HEPA filter life when using cleanable metal prefilters and high flows of steam and water in the offgas scrubber. 8 figs., 2 tabs.

  20. Effect of low pH start-up on continuous mixed-culture lactic acid fermentation of dairy effluent.

    Science.gov (United States)

    Choi, Gyucheol; Kim, Jaai; Lee, Changsoo

    2016-12-01

    Mixed-culture fermentation that does not require an energy-intensive sterilization process is a viable approach for the economically feasible production of lactic acid (LA) due to the potential use of organic waste as feedstock. This study investigated mixed-culture LA fermentation of whey, a high-strength organic wastewater, in continuous mode. Variations in the hydraulic retention time (HRT) from 120 to 8 h under different pH regimes in two thermophilic reactors (55 °C) were compared for their fermentation performance. One reactor was maintained at a low pH (pH 3.0) during operation at HRTs of 120 to 24 h and then adjusted to pH 5.5 in the later phases of fermentation at HRTs of 24 to 8 h (R1), while the second reactor was maintained at pH 5.5 throughout the experiment (R2). Although the LA production in R1 was negligible at low pH, it increased dramatically after the pH was raised to 5.5 and exceeded that in R2 when stabilized at HRTs of 8 and 12 h. The maximum yield (0.62 g LA/g substrate fed as the chemical oxygen demand (COD) equivalent), the production rate (11.5 g/L day), and the selectivity (95 %) of LA were all determined at a 12-h HRT in R1. Additionally, molecular and statistical analyses revealed that changes in the HRT and the pH significantly affected the bacterial community structure and thus the fermentation characteristics of the experimental reactors. Bacillus coagulans was likely the predominant LA producer in both reactors. The overall results suggest that low pH start-up has a positive effect on yield and selectivity in mixed-culture LA fermentation.

  1. Environmental aspects of commercial radioactive waste management

    Energy Technology Data Exchange (ETDEWEB)

    1979-05-01

    Volume 3 contains eight appendices: a reference environment for assessing environmental impacts associated with construction and operation of waste treatment, interim storage and/or final disposition facilities; dose calculations and radiologically related health effects; socioeconomic impact assessments; release/dose factors and dose in 5-year intervals to regional and world wide population from reference integrated systems; resource availability; environmental monitoring; detailed dose results for radionuclide migration groundwater from a waste repository; and annual average dispersion factors for selected release points. (LK)

  2. Consolidated Incineration Facility waste burn test. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Burns, D.B.

    1995-01-11

    The Savannah River Technology Center (SRTC) is Providing technical support for start-up and operation of the Consolidated Incineration Facility. This support program includes a series of pilot incineration tests performed at the Environmental Protection Agency`s (EPA`s) Incineration Research Facility (MF) using surrogate CIF mixed wastes. The objectives for this test program included measuring incinerator offgas particulate loading and size distributions as a function of several operating variables, characterizing kiln bottom ash and offgas particulates, determining heavy metal partition between the kiln bottom ash and incinerator stack gas, and measuring kiln organics emissions (particularly polychlorinated dioxins and furans). These tests were designed to investigate the effect of the following operating parameters: Incineration Temperature; Waste Feed Rate; Waste Density; Kiln Solids Residence Time; and Waste Composition. Tests were conducted at three kiln operating temperatures. Three solid waste simulants were burned, two waste mixtures (paper, plastic, latex, and PVC) with one containing spiked toxic organic and metal compounds, and one waste type containing only paper. Secondary Combustion Chamber (SCC) offgases were sampled for particulate loading and size distribution, organic compounds, polychlorinated dibenzo[p]dioxins and polychlorinated dibenzofurans (PCDD/PCDF), metals, and combustion products. Kiln bottom ash and offgas particulates were characterized to determine the principal elements and compounds comprising these secondary wastes.

  3. Chemical Stabilization of Hanford Tank Residual Waste

    Energy Technology Data Exchange (ETDEWEB)

    Cantrell, Kirk J.; Um, Wooyong; Williams, Benjamin D.; Bowden, Mark E.; Gartman, Brandy N.; Lukens, Wayne W.; Buck, Edgar C.; Mausolf, Edward J.

    2014-03-01

    Three different chemical treatment methods were tested for their ability to stabilize residual waste from Hanford tank C-202 for reducing contaminant release (Tc, Cr, and U in particular). The three treatment methods tested were lime addition [Ca(OH)2], an in-situ Ceramicrete waste form based on chemically bonded phosphate ceramics, and a ferrous iron/goethite treatment. These approaches rely on formation of insoluble forms of the contaminants of concern (lime addition and ceramicrete) and chemical reduction followed by co-precipitation (ferrous iron/goethite incorporation treatment). The results have demonstrated that release of the three most significant mobile contaminants of concern from tank residual wastes can be dramatically reduced after treatment compared to contact with simulated grout porewater without treatment. For uranium, all three treatments methods reduced the leachable uranium concentrations by well over three orders of magnitude. In the case of uranium and technetium, released concentrations were well below their respective MCLs for the wastes tested. For tank C-202 residual waste, chromium release concentrations were above the MCL but were considerably reduced relative to untreated tank waste. This innovative approach has the potential to revolutionize Hanford’s tank retrieval process, by allowing larger volumes of residual waste to be left in tanks while providing an acceptably low level of risk with respect to contaminant release that is protective of the environment and human health. Such an approach could enable DOE to realize significant cost savings through streamlined retrieval and closure operations.

  4. Chemical stabilization of Hanford tank residual waste

    Energy Technology Data Exchange (ETDEWEB)

    Cantrell, Kirk J., E-mail: kirk.cantrell@pnnl.gov [Pacific Northwest National Laboratory, Richland, WA 99352 (United States); Um, Wooyong; Williams, Benjamin D.; Bowden, Mark E.; Gartman, Brandy [Pacific Northwest National Laboratory, Richland, WA 99352 (United States); Lukens, Wayne W. [Lawrence Berkeley National Laboratory, Berkeley, CA 94720 (United States); Buck, Edgar C.; Mausolf, Edward J. [Pacific Northwest National Laboratory, Richland, WA 99352 (United States)

    2014-03-15

    Three different chemical treatment methods were tested for their ability to stabilize residual waste from Hanford tank C-202 for reducing contaminant release (Tc, Cr, and U in particular). The three treatment methods tested were lime addition [Ca(OH){sub 2}], an in situ Ceramicrete waste form based on chemically bonded phosphate ceramics, and a ferrous iron/goethite treatment. These approaches rely on formation of insoluble forms of the contaminants of concern (lime addition and Ceramicrete) and chemical reduction followed by co-precipitation (ferrous iron/goethite incorporation treatment). The results have demonstrated that release of uranium from tank residual wastes can be dramatically reduced after treatment compared to contact with simulated grout porewater without treatment. All three treatments methods reduced the leachable uranium concentrations by well over three orders of magnitude. In the case of uranium and technetium, released concentrations were well below their respective Maximum Contaminant Levels (MCLs) for the wastes tested. For tank C-202 residual waste, chromium release concentrations were above the MCL but were considerably reduced relative to untreated tank waste. This innovative approach has the potential to revolutionize Hanford’s tank retrieval process, by allowing larger volumes of residual waste to be left in tanks while providing an acceptably low level of risk with respect to contaminant release that is protective of the environment and human health. Such an approach could enable DOE to realize significant cost savings through streamlined retrieval and closure operations.

  5. Optimal design method for force in vibration control of multi-body system with quick startup and brake

    Institute of Scientific and Technical Information of China (English)

    TANG Hua-ping; PENG Ya-qing

    2005-01-01

    A kind of active vibration control method was presented through optimal design of driving load of multi-body system with quick startup and brake. Dynamical equation of multi-body system with quick startup and brake was built, and mathematical model of representing vibration control was also set up according to the moving process from startup to brake. Then optimization vibration control model of system driving load was founded by applying theory of optimization control, which takes rigid body moving variable of braking moment as the known condition, and vibration control equation of multi-body system with quick startup and brake was converted into boundary value problem of differential equation. The transient control algorithm of vibration was put forward, which is the analysis basis for the further research. Theoretical analysis and calculation of numerical examples show that the optimal design method for the multi-body system driving load can decrease the vibration of system with duplication.

  6. Strenthening Opportunities Of Economic Relations Between Lithuania And Sweden Within The Perspective Of It Startup Company’s Development

    National Research Council Canada - National Science Library

    Živilė Tunčikienė; Gabrielė Sinkevičiūtė

    2017-01-01

    .... In order to develop and utilize the potential for economic cooperation in the IT field, it is relevant to structuralize IT startup business success factors and to jointly develop base for decisions...

  7. A MEMS stronglink with multi-try function used for PC startup in authentication system

    Institute of Scientific and Technical Information of China (English)

    LI Sheng-yong; CHEN Wen-yuan; ZHANG Wei-ping; XIAO Qi-jun; TAN Shun-yi; FENG Min-hua

    2009-01-01

    The stronglink with multi-try function based on MEMS technology and the PC startup in authentication system have been designed and fabricated. The generation principle and structure of UQS code are introduced, which consists of two groups of metal counter-meshing gears, two pawl/ratchet mechanisms, two driving micromotors and two resetting micromotors. The energy-coupling element is a photoelectric sensor with a circular and notched plate. It is fabricated using the UV-LiGA process and precision mechanical engineering. The PC startup authentication system is controlled by BIOS program, which is written into the chip according with special format. The program in BIOS output signals controls the running of stronglink to finish the process of authentication. The device can run more than 10000 times before a stop. The driving voltage is 12 V, and the normal decoding time is 3 s.

  8. Laboratory tests of a modified {sup 3}He detector for use with startup instrumentation

    Energy Technology Data Exchange (ETDEWEB)

    Qian, T.; Tonner, P.; Keller, N. [Atomic Eerngy of Canada Limited, Chalk River, ON (Canada)] [and others

    1997-07-01

    Boron trifluoride (BF{sub 3}) detectors are currently used in all CANDU stations as startup instrumentation (SUI) detectors for monitoring neutron flux during extended outages and startups. Experience at some CANDU stations has shown that some models of BF{sub 3} detectors degrade quickly, even in moderate neutron and gamma fields. Degradation and life expectancy tests for five models of BF{sub 3} detectors from different manufacturers were performed at Chalk River Laboratories (CRL) to investigate the problem. The test results reveal that most BF{sub 3} detectors have low neutron and gamma durability, and some exhibit an undesirable time-dependent degradation followed by recovery. As a result of this finding, other detector options including a modified helium ({sup 3}He) detector described herein were investigated. Modified {sup 3}He detectors were procured from an established supplier and were found to perform without degradation in neutron and gamma fields. (author)

  9. Disruptive innovation potential of the value propositions of 3D printing technology startups

    DEFF Research Database (Denmark)

    Jensen, Søren; Tanev, Stoyan; Hahn, Finn

    2014-01-01

    3D printing (or additive manufacturing) is a term used to describe the production of tangible products by using digitally controlled machine tools. The novelty of this manufacturing approach consists in the selective addition of materials layer-upon-layer, rather than through machining from solid...... material objects, moulding or casting. 3D printing (3DP) technologies have the potential to change the traditional manufacturing paradigm as well as to enable the emergence of new innovation practices based on mass customization, user design and distributed product innovation. As a result, 3DP...... potential of 3DP technology startups. The objective of this research is to empirically examine the existing business opportunities in the 3D printing technology sector. To meet this objective we have addressed two research questions: a) How do technology startups integrate new 3D printing technologies...

  10. Minimum Viable Product and the Importance of Experimentation in Technology Startups

    Directory of Open Access Journals (Sweden)

    Dobrila Rancic Moogk

    2012-03-01

    Full Text Available Entrepreneurs are often faced with limited resources in their quest to commercialize new technology. This article presents the model of a lean startup, which can be applied to an organization regardless of its size or environment. It also emphasizes the conditions of extreme uncertainty under which the commercialization of new technology is carried out. The lean startup philosophy advocates efficient use of resources by introducing a minimum viable product to the market as soon as possible in order to test its value and the entrepreneur’s growth projections. This testing is done by running experiments that examine the metrics relevant to three distinct types of the growth. These experiments bring about accelerated learning to help reduce the uncertainty that accompanies commercialization projects, thereby bringing the resulting new technology to market faster.

  11. Market Segmentation, Customers, and Value Propositions Analysis for Polymer Clay Art Business Start-Up

    Directory of Open Access Journals (Sweden)

    Desman Hidayat

    2016-05-01

    Full Text Available Polymer clay art is one of the creative businesses that are recently starting to get a lot of attentions. To prepare a startup business in this field, analysis from a lot of aspects is needed. The purpose of this article was to explain the approach of the polymer clay art business startup from the market segmentation, customer, and value proposition side of the business. The method was applied by analyzing those steps in details. The analysis started from brainstorming to choose the market matching to business, the customer side, value proposition, and between both aspects. The result of the analysis shows the business focus of the polymer clay art business, where the value propositions are focusing on unique decorations, and several types of customer segments.

  12. [Start-up characteristics of the anaerobic reactor seeded with immobilized microorganisms].

    Science.gov (United States)

    Wu, Bing-tao; Zhou, Wei-li; Zhang, Zhen-jia; Cheng, Xue-hang; Dong, Ya-mei; Chi, Li-na

    2009-10-15

    In order to overcome the disadvantages of the anaerobic reactor such as slow growth and long start-up, the flocculent anaerobic sludge was embedded and used as the seed sludge in the anaerobic treatment of PTA wastewater with the objective of keeping biomass in the reactor. The start-up characteristics of the UASB reactor were investigated. During the 136 days' running, COD removal rate of PTA wastewater achieved 75%-85% at the volumetric loading rate (COD) of 3 kg x (m3 x d)(-1) and the hydraulic retention time (HRT) of 3-4 day. The anaerobic system had good stability and biomass retaining ability. On the other hand, variations of EPS, SEM observation and methanogens DNA in sludge granules verified the growth of immobilized bacteria in both quantity and microorganism morphology, although mass transfer through the immobilization media was to some degree limited.

  13. Integrated physics analysis of plasma start-up scenario of helical reactor FFHR-d1

    Science.gov (United States)

    Goto, T.; Miyazawa, J.; Sakamoto, R.; Seki, R.; Suzuki, C.; Yokoyama, M.; Satake, S.; Sagara, A.; The FFHR Design Group

    2015-06-01

    1D physics analysis of the plasma start-up scenario of the large helical device (LHD)-type helical reactor FFHR-d1 was conducted. The time evolution of the plasma profile is calculated using a simple model based on the LHD experimental observations. A detailed assessment of the magnetohydrodynamic equilibrium and neo-classical energy loss was conducted using the integrated transport analysis code TASK3D. The robust controllability of the fusion power was confirmed by feedback control of the pellet fuelling and a simple staged variation of the external heating power with a small number of simple diagnostics (line-averaged electron density, edge electron density and fusion power). A baseline operation control scenario (plasma start-up and steady-state sustainment) of the FFHR-d1 reactor for both self-ignition and sub-ignition operation modes was demonstrated.

  14. Solid oxide fuel cell power plant having a bootstrap start-up system

    Science.gov (United States)

    Lines, Michael T

    2016-10-04

    The bootstrap start-up system (42) achieves an efficient start-up of the power plant (10) that minimizes formation of soot within a reformed hydrogen rich fuel. A burner (48) receives un-reformed fuel directly from the fuel supply (30) and combusts the fuel to heat cathode air which then heats an electrolyte (24) within the fuel cell (12). A dilute hydrogen forming gas (68) cycles through a sealed heat-cycling loop (66) to transfer heat and generated steam from an anode side (32) of the electrolyte (24) through fuel processing system (36) components (38, 40) and back to an anode flow field (26) until fuel processing system components (38, 40) achieve predetermined optimal temperatures and steam content. Then, the heat-cycling loop (66) is unsealed and the un-reformed fuel is admitted into the fuel processing system (36) and anode flow (26) field to commence ordinary operation of the power plant (10).

  15. Start-up performance of parabolic trough concentrating solar power plants

    DEFF Research Database (Denmark)

    Ferruzza, Davide; Topel, Monika; Basaran, Ibrahim

    2017-01-01

    Concentrating solar power plants, even though they can be integrated with thermal energy storage, are still subjected to cyclic start-up and shut-downs. As a consequence, in order to maximize their profitability and performance, the flexibility with respect to transient operations is essential....... In this regard, two of the key components identified are the steam generation system and steam turbine. In general it is desirable to have fast ramp-up rates during the start-up of a power plant. However ramp-up rates are limited by, among other things, thermal stresses, which if high enough can compromise...... generator to determine the optimal ramp rates. This paper presents a methodology to account for thermal stresses limitations during the power plant start up, aiming at identifying which components limit the ramp rates. A detailed dynamic model of a parabolic trough power plant was developed and integrated...

  16. Solid oxide fuel cell power plant having a bootstrap start-up system

    Energy Technology Data Exchange (ETDEWEB)

    Lines, Michael T

    2016-10-04

    The bootstrap start-up system (42) achieves an efficient start-up of the power plant (10) that minimizes formation of soot within a reformed hydrogen rich fuel. A burner (48) receives un-reformed fuel directly from the fuel supply (30) and combusts the fuel to heat cathode air which then heats an electrolyte (24) within the fuel cell (12). A dilute hydrogen forming gas (68) cycles through a sealed heat-cycling loop (66) to transfer heat and generated steam from an anode side (32) of the electrolyte (24) through fuel processing system (36) components (38, 40) and back to an anode flow field (26) until fuel processing system components (38, 40) achieve predetermined optimal temperatures and steam content. Then, the heat-cycling loop (66) is unsealed and the un-reformed fuel is admitted into the fuel processing system (36) and anode flow (26) field to commence ordinary operation of the power plant (10).

  17. Fast start-up of expanded granular sludge bed (EGSB) reactor using stored Anammox sludge.

    Science.gov (United States)

    Wenjie, Zhang; Yuanyuan, Zhang; Liang, Li; Xuehong, Zhang; Yue, Jin

    2014-01-01

    Stored Anammox sludge (SAS) was used in an expanded granular sludge bed (EGSB) reactor treating synthetic wastewater with the aim of evaluating its possible use as seed sludge. The SAS had been kept in a refrigerator (4 °C) without any feed. After 2 years, only 1-2% Anammox bacteria could survive in the SAS. However, it soon prevailed in the EGSB reactor after loading. Accordingly, the start-up of the EGSB reactor was successfully completed in 34 days. The biomass turned to round reddish granular sludge from irregular brown floc at the end of this study. The results indicate that SAS could serve well as seed sludge. The required time for start-up of the Anammox reactor using SAS was thus demonstrated to be shorter than that of uncultivated sludge under experimental conditions.

  18. How To Design A Triple Bottom Line Organization: A Start-Up Case Study

    Directory of Open Access Journals (Sweden)

    Bernhard Schroeder

    2014-05-01

    Full Text Available In today’s business environment, where success for a start-up company is measured by early revenue and profit, it can be quite challenging to design a triple bottom line organization (people/planet/profit from the very beginning. We present a case study of a U.S.-based start-up firm and discuss its early challenges, developmental processes, and current success as a triple bottom line firm. The company’s founder and CEO, with no initial product, distribution, or revenue strategy, sought to develop a company that could provide the marketplace with a valuable product while also staying true to a corporate vision of positively affecting less fortunate people. Our analysis of the case suggests that the founder’s vision, passion, transparent communication, and leveraging of partners’ resources were key elements in building the firm. We draw implications of our case study for the designers of future triple bottom line organizations.

  19. Disruptive innovation potential of the value propositions of 3D printing technology startups

    DEFF Research Database (Denmark)

    Jensen, Søren; Tanev, Stoyan; Hahn, Finn

    2014-01-01

    3D printing (or additive manufacturing) is a term used to describe the production of tangible products by using digitally controlled machine tools. The novelty of this manufacturing approach consists in the selective addition of materials layer-upon-layer, rather than through machining from solid...... material objects, moulding or casting. 3D printing (3DP) technologies have the potential to change the traditional manufacturing paradigm as well as to enable the emergence of new innovation practices based on mass customization, user design and distributed product innovation. As a result, 3DP...... potential of 3DP technology startups. The objective of this research is to empirically examine the existing business opportunities in the 3D printing technology sector. To meet this objective we have addressed two research questions: a) How do technology startups integrate new 3D printing technologies...

  20. Life Science Start-up Activities at the Universities of Applied Sciences (UAS).

    Science.gov (United States)

    Huber, Gerda

    2014-12-01

    The universities of applied sciences (UAS) provide several values for the society and economy of a country. Besides education of high level professionals, transfer of knowledge from research to applications in industry or as new start-up companies is an important task. This is done in different ways in the various disciplines. In Life Sciences, a key industry branch in Switzerland, innovation is a competitive success factor and research findings from UAS/Life Sciences contribute to the valorization of new technologies to products, services and to business performance. In order to foster awareness for the innovation need of industry, UAS install processes and support for transfer of research and technology results to marketable applications. Furthermore they may facilitate contacts of researchers and students with entrepreneurs in order to animate start-up founding as a true alternative to being employed. Access to coaching and entrepreneurial training completes the essential basis.

  1. Industrial Waste

    DEFF Research Database (Denmark)

    Christensen, Thomas Højlund

    2011-01-01

    Industrial waste is waste from industrial production and manufacturing. Industry covers many industrial sectors and within each sector large variations are found in terms of which raw materials are used, which production technology is used and which products are produced. Available data on unit...... generation rates and material composition as well as determining factors are discussed in this chapter. Characterizing industrial waste is faced with the problem that often only a part of the waste is handled in the municipal waste system, where information is easily accessible. In addition part...... of the industrial waste may in periods, depending on market opportunities and prices, be traded as secondary rawmaterials. Production-specificwaste from primary production, for example steel slag, is not included in the current presentation. In some countries industries must be approved or licensed and as part...

  2. Waste indicators

    Energy Technology Data Exchange (ETDEWEB)

    Dall, O.; Lassen, C.; Hansen, E. [Cowi A/S, Lyngby (Denmark)

    2003-07-01

    The Waste Indicator Project focuses on methods to evaluate the efficiency of waste management. The project proposes the use of three indicators for resource consumption, primary energy and landfill requirements, based on the life-cycle principles applied in the EDIP Project. Trial runs are made With the indicators on paper, glass packaging and aluminium, and two models are identified for mapping the Danish waste management, of which the least extensive focuses on real and potential savings. (au)

  3. Experience from start-ups of the first ANITA Mox plants.

    Science.gov (United States)

    Christensson, M; Ekström, S; Andersson Chan, A; Le Vaillant, E; Lemaire, R

    2013-01-01

    ANITA™ Mox is a new one-stage deammonification Moving-Bed Biofilm Reactor (MBBR) developed for partial nitrification to nitrite and autotrophic N-removal from N-rich effluents. This deammonification process offers many advantages such as dramatically reduced oxygen requirements, no chemical oxygen demand requirement, lower sludge production, no pre-treatment or requirement of chemicals and thereby being an energy and cost efficient nitrogen removal process. An innovative seeding strategy, the 'BioFarm concept', has been developed in order to decrease the start-up time of new ANITA Mox installations. New ANITA Mox installations are started with typically 3-15% of the added carriers being from the 'BioFarm', with already established anammox biofilm, the rest being new carriers. The first ANITA Mox plant, started up in 2010 at Sjölunda wastewater treatment plant (WWTP) in Malmö, Sweden, proved this seeding concept, reaching an ammonium removal rate of 1.2 kgN/m³ d and approximately 90% ammonia removal within 4 months from start-up. This first ANITA Mox plant is also the BioFarm used for forthcoming installations. Typical features of this first installation were low energy consumption, 1.5 kW/NH4-N-removed, low N₂O emissions, Mox plant, started up at Sundets WWTP in Växjö, Sweden, reached full capacity with more than 90% ammonia removal within 2 months from start-up. By applying a nitrogen loading strategy to the reactor that matches the capacity of the seeding carriers, more than 80% nitrogen removal could be obtained throughout the start-up period.

  4. Start-up performance of parabolic trough concentrating solar power plants

    Science.gov (United States)

    Ferruzza, Davide; Topel, Monika; Basaran, Ibrahim; Laumert, Björn; Haglind, Fredrik

    2017-06-01

    Concentrating solar power plants, even though they can be integrated with thermal energy storage, are still subjected to cyclic start-up and shut-downs. As a consequence, in order to maximize their profitability and performance, the flexibility with respect to transient operations is essential. In this regard, two of the key components identified are the steam generation system and steam turbine. In general it is desirable to have fast ramp-up rates during the start-up of a power plant. However ramp-up rates are limited by, among other things, thermal stresses, which if high enough can compromise the life of the components. Moreover, from an operability perspective it might not be optimal to have designs for the highest heating rates, as there may be other components limiting the power plant start-up. Therefore, it is important to look at the interaction between the steam turbine and steam generator to determine the optimal ramp rates. This paper presents a methodology to account for thermal stresses limitations during the power plant start up, aiming at identifying which components limit the ramp rates. A detailed dynamic model of a parabolic trough power plant was developed and integrated with a control strategy to account for the start-up limitations of both the turbine and steam generator. The models have been introduced in an existing techno-economic tool developed by the authors (DYESOPT). The results indicated that for each application, an optimal heating rates range can be identified. For the specific case presented in the paper, an optimal range of 7-10 K/min of evaporator heating rate can result in a 1.7-2.1% increase in electricity production compared to a slower component (4 K/min).

  5. Load adaptive start-up scheme for synchronous boost DC-DC converter

    Science.gov (United States)

    Guoding, Dai; Wenliang, Xiu; Yuezhi, Liu; Yawei, Qi; Zuqi, Dong

    2016-10-01

    This paper presents a load adaptive soft-start scheme through which the inductor current of the synchronous boost DC-DC converter can trace the load current at the start-up stage. This scheme effectively eliminates the inrush-current and over-shoot voltage and improves the load capability of the converter. According to the output voltage, the start-up process is divided into three phases and at each phase the inductor current is limited to match the load. In the pre-charge phase, a step-increasing constant current gives a smooth rise of the output voltage which avoids inrush current and ensures the converter successfully starts up at different load situations. An additional ring oscillator operation phase enables the converter to start up as low as 1.4 V. When the converter enters into the system loop soft-start phase, an output voltage and inductor current detection methods make the transition of the phases smooth and the inductor current and output voltage rise steadily. Effective protection circuits such as short-circuit protection, current limit circuit and over-temperature protection circuit are designed to guarantee the safety and reliability of the chip during the start-up process. The proposed start-up circuit is implemented in a synchronous boost DC-DC converter based on TSMC 0.35 μm CMOS process with an input voltage range 1.4-4.2 V, and a steady output voltage 5 V, and the switching frequency is 1 MHz. Simulation results show that inrush current and overshoot voltage are suppressed with a load range from 0-2.1 A, and inductor current is as low as 259 mA when the output shorts to the ground.

  6. Digital Start-Ups in the Global South:Embeddedness, Digitality and Peripherality in Latin America

    OpenAIRE

    Quinones, Gerardo; Heeks, Richard; Nicholson, Brian

    2017-01-01

    There is debate about the extent to which digital activity is embedded or disembedded from various aspects of its context including place, institutions and networks. Yet little research has so far been conducted on this issue in relation to digital enterprises, particularly those in developing countries. Because of the growing importance of the digital economy in developing countries, an interview- and observation-based research study was undertaken of digital start-ups in the four largest La...

  7. Ignore the Unicorn: the overhyped startups with multibillion-dollar valuations are setting a bad example

    National Research Council Canada - National Science Library

    Brodsky, Norm

    2016-01-01

    ... they do it? "Volume." That works for a tiny percentage of startups, but it's a recipe for failure for the vast majority of entrepreneurs who--no matter how cool their idea--will never have access to the amount of outside capital needed to keep a company going for years if it's not earning a profit. I'll give you the example of a couple of bright and idealisti...

  8. Public policy for start-up entrepreneurship with venture capital and bank finance

    DEFF Research Database (Denmark)

    Keuschnigg, Christian; Nielsen, Søren Bo

    2003-01-01

    This paper proposes and analyses a model of start-up investment. Innovative entrepreneursare commercially inexperienced and can benefit from venture capital support. Only part ofthem succeed in matching with a venture capitalist while the rest must resort to standard bankfinance. We consider a nu...... a number of policies to promote entrepreneurship and venture capitalbacked innovation.JEL Classification: D82, G24, G28, H24.Keywords: venture capital bank finance, matching, moral hazard, public policy....

  9. Preheating of fluid in a supercritical Brayton cycle power generation system at cold startup

    Science.gov (United States)

    Wright, Steven A.; Fuller, Robert L.

    2016-07-12

    Various technologies pertaining to causing fluid in a supercritical Brayton cycle power generation system to flow in a desired direction at cold startup of the system are described herein. A sensor is positioned at an inlet of a turbine, wherein the sensor is configured to output sensed temperatures of fluid at the inlet of the turbine. If the sensed temperature surpasses a predefined threshold, at least one operating parameter of the power generation system is altered.

  10. Refugee Business Start-ups in the North East of England: An Impossible Dream?

    OpenAIRE

    Davidson, Hilary; Fitzgerald, Ian; Hudson, Lucinda

    2013-01-01

    Objectives and prior work - For many asylum seekers just getting to the UK is an achievement, let alone obtaining refugee status. When ‘equality’ is achieved with other immigrant workers then the settlement process begins. For some this includes starting a business but there are a number of well documented barriers to business start-up for refugees as well as black minority ethic entrepreneurs, which have been highlighted in the North East region (BRKN, 2007). Given this Northumbria Universit...

  11. Ant Colony Search Algorithm for Optimal Generators Startup during Power System Restoration

    OpenAIRE

    A. Ketabi; Feuillet, R

    2010-01-01

    Generators startup sequence plays a significant role in achieving a suitable and effective restoration strategy. This paper outlines an ant colony search algorithm in order to determine the generator starting times during the bulk power system restoration. The algorithm attempts to maximize the system generation capability over a restoration period, where the dynamic characteristics of different types of units and system constraints are considered. Applying this method for the 39-bus New Engl...

  12. Creating a Business Plan for a Start-up Business Consultancy in Namibia

    OpenAIRE

    von Wietersheim, Julia

    2011-01-01

    The objective of this Thesis is to investigate the process of creating an extensive Business Plan and thereby to practically apply the theory studied during the Degree Programme of International Business. To achieve this objective, a practical business plan for a start-up Business Consultancy in Namibia (called VW-Business Consulting) is created, which at the same time provides a deeper understanding of the current demand for, and awareness of, business consulting companies in Namibia. An...

  13. Emissions Characterisation of residential pellet boilers during start-up and stop periods

    OpenAIRE

    Win, Kaung Myat; Paavilainen, Janne; Persson, Tomas

    2010-01-01

    In this study, gaseous emissions and particles are measured during start-up and stop periods for an over-fed boiler and an under-fed boiler. Both gaseous and particulate matter emissions are continuously measured in the laboratory. The measurement of gaseous emissions includes oxygen (O2), carbon dioxide (CO2), carbon monoxide (CO), nitrogen oxide and (NO). The emissions rates are calculated from measured emissions concentrations and flue gas flow. The behaviours of the boilers during start-u...

  14. ENTREPRENEURIAL FINANCE: ANGEL INVESTING AS A SOURCE OF FUNDING HIGH-GROWTH START-UP FIRMS

    Directory of Open Access Journals (Sweden)

    SONJA MARKOVA

    2010-01-01

    Full Text Available One of the most difficult components in starting and growing a new venture is securing funding and other resources to sustain the firm’s survival and growth. Funding for many new ventures comes from a large, yet relatively unidentified, group called angel investors. This paper provides an overview of angel investing as a source of funding for start-up firms.

  15. Start-Up Performance of Ground-Water Recharge Trenches Rocky Mountain Arsenal

    Science.gov (United States)

    1989-08-01

    8217 rLASSIFICAT!ON OF THIS PAGE Unclassified SECURIT ’, CLASSIFICATION OF THIS PAGE SECURITY CL.ASSfFICATION OF THISPAGE PREFACE Field investigations were...10 only. ** Data collected after start-up period. LU L9% LA A~ en w! Z 12 w r,..u I- CC. o t)- 00q f It - 4g T 0 , . L .3X ci 0 0 -K o 04 0 0 0

  16. Public policy for start-up entrepreneurship with venture capital and bank finance

    DEFF Research Database (Denmark)

    Keuschnigg, Christian; Nielsen, Søren Bo

    2003-01-01

    This paper proposes and analyses a model of start-up investment. Innovative entrepreneursare commercially inexperienced and can benefit from venture capital support. Only part ofthem succeed in matching with a venture capitalist while the rest must resort to standard bankfinance. We consider...... a number of policies to promote entrepreneurship and venture capitalbacked innovation.JEL Classification: D82, G24, G28, H24.Keywords: venture capital bank finance, matching, moral hazard, public policy....

  17. Assessment of Startup Fuel Options for a Test or Demonstration Fast Reactor

    Energy Technology Data Exchange (ETDEWEB)

    Carmack, Jon [Idaho National Lab. (INL), Idaho Falls, ID (United States); Hayes, Steven [Idaho National Lab. (INL), Idaho Falls, ID (United States); Walters, L. C. [Idaho National Lab. (INL), Idaho Falls, ID (United States)

    2015-09-01

    This document explores startup fuel options for a proposed test/demonstration fast reactor. The fuel options considered are the metallic fuels U-Zr and U-Pu-Zr and the ceramic fuels UO2 and UO2-PuO2 (MOX). Attributes of the candidate fuel choices considered were feedstock availability, fabrication feasibility, rough order of magnitude cost and schedule, and the existing irradiation performance database. The reactor-grade plutonium bearing fuels (U-Pu-Zr and MOX) were eliminated from consideration as the initial startup fuels because the availability and isotopics of domestic plutonium feedstock is uncertain. There are international sources of reactor grade plutonium feedstock but isotopics and availability are also uncertain. Weapons grade plutonium is the only possible source of Pu feedstock in sufficient quantities needed to fuel a startup core. Currently, the available U.S. source of (excess) weapons-grade plutonium is designated for irradiation in commercial light water reactors (LWR) to a level that would preclude diversion. Weapons-grade plutonium also contains a significant concentration of gallium. Gallium presents a potential issue for both the fabrication of MOX fuel as well as possible performance issues for metallic fuel. Also, the construction of a fuel fabrication line for plutonium fuels, with or without a line to remove gallium, is expected to be considerably more expensive than for uranium fuels. In the case of U-Pu-Zr, a relatively small number of fuel pins have been irradiated to high burnup, and in no case has a full assembly been irradiated to high burnup without disassembly and re-constitution. For MOX fuel, the irradiation database from the Fast Flux Test Facility (FFTF) is extensive. If a significant source of either weapons-grade or reactor-grade Pu became available (i.e., from an international source), a startup core based on Pu could be reconsidered.

  18. NTN Swiss Biotech - A Look at Support Measures for Dynamic Start-ups.

    Science.gov (United States)

    Heinzelmann, Elsbeth

    2016-01-01

    The Swiss biotech landscape seems to be on a healthy footing: There are many imaginative start-ups, we have first-class hospitals, highly advanced clinical research and the availability of a great deal of capital. But we have no reason to rest on our laurels as countries like the USA lead the field. We must lay down the tracks today to remain an attractive country and maintain our ranking among the 10 best locations.

  19. Radioactive releases at the Savannah River Site, 1954--1988

    Energy Technology Data Exchange (ETDEWEB)

    Hetrick, C.S.; Martin, D.K.

    1988-01-01

    Radioactive Releases at the Savannah River Site, 1954--1988 (WSRC-RP-89-737) is the continuation of a series of reports, previously titled Releases of Radioactivity at the Savannah River Plant (DPSU-1-YR-25). The series reflects the use of air and liquid effluent sample analyses in determining the amount of radioactivity released from Savannah River Site (SRS) operations. The identification and characterization of these source terms since plant startup in 1954 have aided Site personnel in confining and limiting the amount of radioactivity released to the environment from SRS facilities. Data contained in this report are used for a variety of purposes, including the calculation of offsite dose estimates and aiding special environmental studies. This document is an effluent/source term report. The report is divided into four summary sections. Summary A details volumes of air and water released from emission sources since plant startup. Summary B lists annual radioactive release data from these emission sources, grouped by nuclide and area. Summary C provides yearly totals of radioactive releases by radionuclide, under the headings Atmospheric,'' Liquid to streams,'' or Liquid to Seepage Basins'' accordingly. Monthly radioactive releases from each emission source from 1986 to 1988 are found in Summary D. Where appropriate, headings in the summary tables have been changed to clarify and simplify emission data (see Appendix B). Additionally, any new discharge points, such as the liquid discharge from the Effluent Treatment Facility (ETF), are included in this report. A listing of 1988 source term and onsite discharge designations is provided in Appendix C. 36 refs.

  20. Radionuclide Retention in Concrete Waste Forms

    Energy Technology Data Exchange (ETDEWEB)

    Mattigod, Shas V.; Bovaird, Chase C.; Wellman, Dawn M.; Wood, Marcus I.

    2010-09-30

    Assessing long-term performance of Category 3 waste cement grouts for radionuclide encasement requires knowledge of the radionuclide-cement interactions and mechanisms of retention (i.e., sorption or precipitation); the mechanism of contaminant release; the significance of contaminant release pathways; how waste form performance is affected by the full range of environmental conditions within the disposal facility; the process of waste form aging under conditions that are representative of processes occurring in response to changing environmental conditions within the disposal facility; the effect of waste form aging on chemical, physical, and radiological properties; and the associated impact on contaminant release. This knowledge will enable accurate prediction of radionuclide fate when the waste forms come in contact with groundwater. The information presented in the report provides data that 1) quantify radionuclide retention within concrete waste form materials similar to those used to encapsulate waste in the Low-Level Waste Burial Grounds (LLBG); 2) measure the effect of concrete waste form properties likely to influence radionuclide migration; and 3) quantify the stability of uranium-bearing solid phases of limited solubility in concrete.

  1. Planning and management of E-commerce Website : Guide for startup B2C E-commerce companies

    OpenAIRE

    Wang, Ying

    2016-01-01

    The purpose of this thesis is to help startup B2C E-commerce companies to plan and manage e-commerce website. This thesis is intended to equip current and future e-commerce managers or entrepreneurs with some basic knowledge and practical skills to help them navigate their organisations towards e-business. It does not have any specific commissioner. Thesis will contain most aspects when plan and manage e-commerce website for startups.

  2. Startup of air-cooled condensers and dry cooling towers at low temperatures of the cooling air

    Science.gov (United States)

    Milman, O. O.; Ptakhin, A. V.; Kondratev, A. V.; Shifrin, B. A.; Yankov, G. G.

    2016-05-01

    The problems of startup and performance of air-cooled condensers (ACC) and dry cooling towers (DCT) at low cooling air temperatures are considered. Effects of the startup of the ACC at sub-zero temperatures are described. Different options of the ACC heating up are analyzed, and examples of existing technologies are presented (electric heating, heating up with hot air or steam, and internal and external heating). The use of additional heat exchanging sections, steam tracers, in the DCT design is described. The need for high power in cases of electric heating and heating up with hot air is noted. An experimental stand for research and testing of the ACC startup at low temperatures is described. The design of the three-pass ACC unit is given, and its advantages over classical single-pass design at low temperatures are listed. The formation of ice plugs inside the heat exchanging tubes during the start-up of ACC and DCT at low cooling air temperatures is analyzed. Experimental data on the effect of the steam flow rate, steam nozzle distance from the heat-exchange surface, and their orientation in space on the metal temperature were collected, and test results are analyzed. It is noted that the surface temperature at the end of the heat up is almost independent from its initial temperature. Recommendations for the safe start-up of ACCs and DCTs are given. The heating flow necessary to sufficiently heat up heat-exchange surfaces of ACCs and DCTs for the safe startup is estimated. The technology and the process of the heat up of the ACC with the heating steam external supply are described by the example of the startup of the full-scale section of the ACC at sub-zero temperatures of the cooling air, and the advantages of the proposed start-up technology are confirmed.

  3. Planning and management of E-commerce Website : Guide for startup B2C E-commerce companies

    OpenAIRE

    Wang, Ying

    2016-01-01

    The purpose of this thesis is to help startup B2C E-commerce companies to plan and manage e-commerce website. This thesis is intended to equip current and future e-commerce managers or entrepreneurs with some basic knowledge and practical skills to help them navigate their organisations towards e-business. It does not have any specific commissioner. Thesis will contain most aspects when plan and manage e-commerce website for startups.

  4. Modeling the Financial Distress of Microenterprise StartUps Using Support Vector Machines: A Case Study

    Directory of Open Access Journals (Sweden)

    Antonio Blanco-Oliver

    2014-10-01

    Full Text Available Despite the leading role that micro-entrepreneurship plays in economic development, and the high failure rate of microenterprise start-ups in their early years, very few studies have designed financial distress models to detect the financial problems of micro-entrepreneurs. Moreover, due to a lack of research, nothing is known about whether non-financial information and nonparametric statistical techniques improve the predictive capacity of these models. Therefore, this paper provides an innovative financial distress model specifically designed for microenterprise startups via support vector machines (SVMs that employs financial, non-financial, and macroeconomic variables. Based on a sample of almost 5,500 micro- entrepreneurs from a Peruvian Microfinance Institution (MFI, our findings show that the introduction of non-financial information related to the zone in which the entrepreneurs live and situate their business, the duration of the MFI-entrepreneur relationship, the number of loans granted by the MFI in the last year, the loan destination, and the opinion of experts on the probability that microenterprise start-ups may experience financial problems, significantly increases the accuracy performance of our financial distress model. Furthermore, the results reveal that the models that use SVMs outperform those which employ traditional logistic regression (LR analysis.

  5. Non-inductive Plasma Start-up and Current Ramp-up in NSTX-U

    Science.gov (United States)

    Raman, R.; Jarboe, T. R.; Jardin, S. C.; Kessel, C. E.; Mueller, D.; Nelson, B. A.; Poli, F.; Taylor, G.; NSTX Research Team; Princeton Plasma Physics Laboratory Team

    2013-10-01

    Results from NSTX Transient Coaxial Helicity Injection (CHI) experiments have demonstrated generation of 300 kA start-up currents, and when these discharges were coupled to induction they attained 1 MA of plasma current consuming 65% of the inductive flux of standard inductive-only discharges in NSTX. The NSTX-U device, which is now under construction at PPPL, will have numerous improvements to enhance transient CHI start-up. These are: (1) factor of two increase in toroidal field, (2) more than 2.5 times the injector flux, (3) increased CHI voltage, (4) full lithium coverage to reduce low-Z impurities and (5) 1 MW ECH system for increasing the electron temperature of CHI discharges to allow direct coupling to NBI current drive using a new second more tangential neutral beam system. In support of NSTX-U objectives for full non-inductive start-up and current ramp-up, the TSC code has been used for a full discharge simulation in which a transient CHI discharge is used as the front end of the non-inductive current ramp-up simulation. This work supported by U.S. DOE Contracts DE-AC02-09CH11466 and DE-FG02-99ER54519 AM08.

  6. Influence of external circulation on sludge characteristics during start-up of internal circulation reactor

    Institute of Scientific and Technical Information of China (English)

    DING Jian-nan; WANG Dian-zuo

    2005-01-01

    The start-up of external circulation-added internal circulation(IC) reactor was finished in 26 d, 32 d fewer than that of IC reactor. To evaluate the influence of the added external circulation on the development of granular sludge, the characteristics of the granular sludge taken from the two tested laboratory-scale reactors during start-up were studied. The results show that the added external circulation can enhance biomass granulation, accelerate granule development and improve sludge characteristics. At the end of start-up, the granular size of sludge in external circulation-added IC reactor greatly increases with a size distribution much better than that of sludge in IC reactor. The granular sludge originated from external circulation-added IC reactor contains more extracellular polymers and has a greater settling velocity than that from IC reactor. Methanogenic activity of the granular sludge from the external circulation-added IC reactor started 26 d ago reaches 358.23 mL·g-1·d-1, 1.66 and 1.20 times as great as that of the sludge from the IC reactor started 26 d and 58 d ago respectively.

  7. [Influence of the difference in start-up echo on signal intensity in the FIESTA sequence].

    Science.gov (United States)

    Naka, Takanori; Takahashi, Mitsuyuki

    2008-11-20

    The FIESTA sequence is a fast imaging method used for various parts in recent years. A constant flip angle (CFA) or linear flip angle (LFA) are used as the start-up echo in many cases. It is reported from CFA, which is the conventional method, that the T1 value and T2 value influence the speed that reaches steady state. However, there is no such report in LFA. Therefore, we examined the influence of the difference of start-up echo method upon signal intensity. In phantoms other than vegetable oil, the difference was not accepted in the change of speed that reaches steady state and the signal intensity in steady-state transit. In LFA, signal intensity of vegetable oil was clearly lower than CFA. The same result was obtained regardless of on or off resonance. From the result, it was thought that it depended on T2/T1 for the speed that reaches steady state. Moreover, the difference in resonant frequency was considered to greatly influence LFA but not CFA. That is, it was suggested by the difference in start-up echo that the signal intensity of fat changes greatly.

  8. Entrepreneurism from the ground up: Entrepreneurism, innovation, and responsiveness in a start-up university

    Science.gov (United States)

    Wong, Michael Paul Anthony

    Colleges and universities are under increased pressure from internal and external constituencies for increased innovation and responsiveness. Entrepreneurial private industry models such as start-up businesses, corporate ventures and spin-off organizations have been recognized for their ability to quickly adapt to changing business environments and rapidly innovate to take advantage of new opportunities. This case study investigates these claims with regard to a start-up university founded with the identity of an entrepreneurial, interdisciplinary institution that prepares graduate level students for leadership careers as entrepreneurs in the bio-tech industry. By interviewing twenty-four administrators, faculty, and members of the Board of Trustees, including all but one of the founding full-time faculty, I present an "insider's" depiction of the lived experience of those most closely associated with the founding and subsequent institution building of this unique higher education organization. Initial chapters present a theory of higher education organizations, derived from Birnbaum (1988) and Bolman and Deal (1991), as driven by two primary tasks: resolving identity and establishing power and resources in relation to that identity. I also present Russell and Russell's (1992) theory of "entrepreneurial posture" in relation to a higher education organization. Subsequent chapters analyze the start-up university's environment, strategy, culture, and structure within the framework of the two primary organizational tasks and Russell and Russell's (1992) definition of an entrepreneurial organization.

  9. STARTUP OF UPELOW ANAEROBIC SLUDGE BLANKET REACTOR FOR INDUSTRIAL WASTEWATER TREATMENT

    Directory of Open Access Journals (Sweden)

    A.R. Mesdaghinia

    1994-06-01

    Full Text Available Up flow anaerobic sludge blanket (UASB reactors have been increasingly used for industrial wastewater treatment. Because of existing problems in startup step of these reactors, in this research the startup of a UASB in pilot scale and room temperature condition was studied. The total height of UASB reactor was 270 cm and effective height was 240 cm. Diameter of the reactor in lower part was 20 cm (reaction zone and 40 cm in upper part (solid-gas-liquid separator five sampling ports with interval of 32 cm were provided and the effective volume of the reactor was 100 liters. Septic tank digested sludge and cow manure were used for the seeding of UASB reactor. In the startup step of the reactor, volumetric loading was increased step by step. After 155 days granule formation was observed and after 215 days of the study the removal rate increased to 4.62 kg COD/m/ day. More than 98% of soluble COD removal was achieved in lower 160 cm of reactor.

  10. Examination of microbial fuel cell start-up times with domestic wastewater and additional amendments

    KAUST Repository

    Liu, Guangli

    2011-08-01

    Rapid startup of microbial fuel cells (MFCs) and other bioreactors is desirable when treating wastewaters. The startup time with unamended wastewater (118h) was similar to that obtained by adding acetate or fumarate (110-115h), and less than that with glucose (181h) or Fe(III) (353h). Initial current production took longer when phosphate buffer was added, with startup times increasing with concentration from 149h (25mM) to 251h (50mM) and 526h (100mM). Microbial communities that developed in the reactors contained Betaproteobacteria, Acetoanaerobium noterae, and Chlorobium sp. Anode biomass densities ranged from 200 to 600μg/cm2 for all amendments except Fe(Sh{cyrillic}) (1650μg/cm2). Wastewater produced 91mW/m2, with the other MFCs producing 50mW/m2 (fumarate) to 103mW/m2 (Fe(III)) when amendments were removed. These experiments show that wastewater alone is sufficient to acclimate the reactor without the need for additional chemical amendments. © 2011 Elsevier Ltd.

  11. On a difficulty in eigenfunction expansion solutions for the start-up of fluid flow

    Science.gov (United States)

    Christov, Ivan C.

    2015-11-01

    Most mathematics and engineering textbooks describe the process of ``subtracting off'' the steady state of a linear parabolic partial differential equation as a technique for obtaining a boundary-value problem with homogeneous boundary conditions that can be solved by separation of variables (i.e., eigenfunction expansions). While this method produces the correct solution for the start-up of the flow of, e.g., a Newtonian fluid between parallel plates, it can lead to erroneous solutions to the corresponding problem for a class of non-Newtonian fluids. We show that the reason for this is the non-rigorous enforcement of the start-up condition in the textbook approach, which leads to a violation of the principle of causality. Nevertheless, these boundary-value problems can be solved correctly using eigenfunction expansions, and we present the formulation that makes this possible (in essence, an application of Duhamel's principle). The solutions obtained by this new approach are shown to agree identically with those obtained by using the Laplace transform in time only, a technique that enforces the proper start-up condition implicitly (hence, the same error cannot be committed). Supported, in part, by NSF Grant DMS-1104047 and the U.S. DOE (Contract No. DE-AC52-06NA25396) through the LANL/LDRD Program.

  12. Theoretical analysis of start-up power in helium pulsating heat pipe

    Science.gov (United States)

    Li, Monan; Huang, Rongjin; Xu, Dong; Li, Laifeng

    2017-02-01

    An analytical model for one-turn helium pulsating heat pipes (PHPs) with single liquid slug and vapor plug is established in present study. When an additional heat power takes place in the evaporating section, temperature and pressure will increase. The pressure wave travels through vapor and liquid phases at different speed, producing a pressure difference in the system, which acts as an exciting force to start up the oscillating motion. Results show that the start-up power of helium PHP is related to the filling ratio. The start-up power increases with the filling ration. However, there exist an upper limit. Furthermore, the start-up power also depends on the inclination angle of PHP. When the inclination angle increases, the heat input needed to start up the oscillating motion decreases. But for one-turn helium PHP, it can not be started up when the inclination angle is up to 90°, equalling to horizontal position,. While the inclination angle ranges between 0° (vertical position) and 75°, it can operate successfully.

  13. [Quick Start-up and Sustaining of Shortcut Nitrification in Continuous Flow Reactor].

    Science.gov (United States)

    Wu, Peng; Zhang Shi-ying; Song, Yin-ling; Xu, Yue-zhong; Shen, Yao-liang

    2016-04-15

    How to achieve fast and stable startup of shortcut nitrification has a very important practical value for treatment of low C/N ratio wastewater. Thus, the quick start-up and sustaining of shortcut nitrification were investigated in continuous flow reactor targeting at the current situation of urban wastewater treatment plant using a continuous flow process. The results showed that quick start-up of shortcut nitrification could be successfully achieved in a continuous flow reactor after 60 days' operation with intermittent aeration and controlling of three stages of stop/aeration time (15 min/45 min, 45 min/45 min and 30 min/30 min). The nitrification rates could reach 90% or 95% respectively, while influent ammonia concentrations were 50 or 100 mg · L⁻¹ with stop/aeration time of 30 min/30 min. In addition, intermittent aeration could inhibit the activity of nitrite oxidizing bacteria (NOB), while short hydraulic retention time (HRT) may wash out NOB. And a combined use of both measures was beneficial to sustain shortcut nitrification.

  14. Time-Frequency Analysis of Rocket Nozzle Wall Pressures During Start-up Transients

    Science.gov (United States)

    Baars, Woutijn J.; Tinney, Charles E.; Ruf, Joseph H.

    2011-01-01

    Surveys of the fluctuating wall pressure were conducted on a sub-scale, thrust- optimized parabolic nozzle in order to develop a physical intuition for its Fourier-azimuthal mode behavior during fixed and transient start-up conditions. These unsteady signatures are driven by shock wave turbulent boundary layer interactions which depend on the nozzle pressure ratio and nozzle geometry. The focus however, is on the degree of similarity between the spectral footprints of these modes obtained from transient start-ups as opposed to a sequence of fixed nozzle pressure ratio conditions. For the latter, statistically converged spectra are computed using conventional Fourier analyses techniques, whereas the former are investigated by way of time-frequency analysis. The findings suggest that at low nozzle pressure ratios -- where the flow resides in a Free Shock Separation state -- strong spectral similarities occur between fixed and transient conditions. Conversely, at higher nozzle pressure ratios -- where the flow resides in Restricted Shock Separation -- stark differences are observed between the fixed and transient conditions and depends greatly on the ramping rate of the transient period. And so, it appears that an understanding of the dynamics during transient start-up conditions cannot be furnished by a way of fixed flow analysis.

  15. Analysis of Three Actors: Roles of Government, Private Sector, and University toward Startup Growth in Yogyakarta

    Directory of Open Access Journals (Sweden)

    Cinintya Audori Fathin

    2016-05-01

    Full Text Available Information, communication, and technology advancements in 21st century encourage startups to innovate and develop their business further. Because it’s an ICT based business which is supported by the existence of internet, this kind of business starts to become borderless. As a result, the distributions of the products start to become unlimited. The conveniences offered by these advancements invite more ICT based product developers. The positive impact as a result of that such as more new jobs, easier way to access the markets, and also cheaper production cost with guaranteed profits. In addition to that, this of course also becomes an added value to the country because it increases Network Readiness Index and nation’s income from taxes. This research aims to analyze startup’s growth, in addition to its relation with related actors such as government, private sectors, and universities. Analysis on every actor will emphasize on their contribution to startup developments in Daerah Istimewa Yogyakarta directly or indirectly. In conclusion, there will be an illustration about how big the contributions and how close the actors are between startups and the three actors.

  16. Using Social Media to Accelerate the Internationalization of Startups from Inception

    Directory of Open Access Journals (Sweden)

    Tony Maltby

    2012-10-01

    Full Text Available A set of principles, processes, and tools that entrepreneurs can use to rapidly internationalize their technology startups from inception does not exist. This article discusses entrepreneurs’ use of online social media networks to rapidly internationalize their startups from inception. The article was inspired by how the founders of Dewak S.A. rapidly internationalized their technology startup. Dewak was founded by five unemployed Colombians in June 2008. Two years later, foreign sales comprised 95% of the firm’s revenue and provided the founders with full-time employment. Dewak’s only channel to market was via online social media networks. Recognizing that entrepreneurs can use social media to amplify their tacit knowledge and convert it into sellable products and services contributes to the development of a learning-based view of rapid internationalization from inception. The article provides entrepreneurs seeking to launch and grow global businesses with four recommendations that may save them time and money and increase the size of their addressable markets.

  17. Reduced waste generation, FY 1986

    Energy Technology Data Exchange (ETDEWEB)

    1986-02-01

    The United States Department of Energy is committed to the principles of minimizing the quantity and transuranic content of its transuranium (TRU) waste being generated at its nuclear facilities. The reasons are to reduce costs associated with waste handling and disposal, and also to reduce radiation exposure to workers and risk for radionuclide release to man and the environment. The purpose of this document is to provide the USDOE with a plan of research and development tasks for waste minimization, and is prepared so as to provide the maximum impact on volumes based on cost/benefit factors. The document is to be updated annually or as needed to reflect current and future tasks. The Reduced Waste Generation (RWG) tasks encompass a wide range of activities with the principal goals of (1) preventing the generation of waste and (2) converting TRU waste into low-level wastes (LLW) by sorting or decontamination. Concepts for reducing the volume such as in incineration and compaction are considered within the discipline of Reduced Waste Generation, but are considered as somewhat developed technology with only a need for implementation. 33 refs.

  18. Effect of the Modification of the Start-Up Sequence on the Thermal Stresses for a Microgas Turbine

    Directory of Open Access Journals (Sweden)

    Oscar Tenango-Pirin

    2016-01-01

    Full Text Available Microgas turbines (MGT are an alternative for small-scale energy production; however, their small size becomes a drawback since it enhances the heat transfer among their components. Moreover, heat transfer drives to temperature gradients which become higher during transient cycles like start-up. The influence of different start-up curves on temperature and thermal stresses of a microgas turbine was investigated. Stationary and rotational blades of the turbine were numerically simulated using CFD and FEM commercial codes. Conjugated heat transfer cases were solved for obtaining heat transfer from fluid toward the blades. Changes of temperature gradients within the blades during the start-ups were calculated under transient state with boundary conditions according to each curve to assess accurate thermal stresses calculations. Results showed that the modification of the start-up curves had an impact on the thermal stresses levels and on the time when highest stresses appeared on each component. Furthermore, zones highly stressed were located near the constraints of blades where thermal strains are restricted. It was also found that the curve that had a warming period at the beginning of the start-up allowed reducing the peaks of stresses making it more feasible and safer for the turbine start-up operation.

  19. Electrical start-up for diesel fuel processing in a fuel-cell-based auxiliary power unit

    Science.gov (United States)

    Samsun, Remzi Can; Krupp, Carsten; Tschauder, Andreas; Peters, Ralf; Stolten, Detlef

    2016-01-01

    As auxiliary power units in trucks and aircraft, fuel cell systems with a diesel and kerosene reforming capacity offer the dual benefit of reduced emissions and fuel consumption. In order to be commercially viable, these systems require a quick start-up time with low energy input. In pursuit of this end, this paper reports an electrical start-up strategy for diesel fuel processing. A transient computational fluid dynamics model is developed to optimize the start-up procedure of the fuel processor in the 28 kWth power class. The temperature trend observed in the experiments is reproducible to a high degree of accuracy using a dual-cell approach in ANSYS Fluent. Starting from a basic strategy, different options are considered for accelerating system start-up. The start-up time is reduced from 22 min in the basic case to 9.5 min, at an energy consumption of 0.4 kW h. Furthermore, an electrical wire is installed in the reformer to test the steam generation during start-up. The experimental results reveal that the generation of steam at 450 °C is possible within seconds after water addition to the reformer. As a result, the fuel processor can be started in autothermal reformer mode using the electrical concept developed in this work.

  20. Strenthening Opportunities of Economic Relations between Lithuania and Sweden within the Perspective of IT Startup Company’s Development

    Directory of Open Access Journals (Sweden)

    Živilė Tunčikienė

    2017-06-01

    Full Text Available Cooperation with Sweden – one of the key priorities of Lithuania. Economic cooperation potential is promising. One of the priority areas of economic activity, in which Sweden invests in Lithuania, is information and communication. In order to develop and utilize the potential for economic cooperation in the IT field, it is relevant to structuralize IT startup business success factors and to jointly develop base for decisions, execution of which would help ensure effective, economic co-operation development based with Sweden, beginning of IT startup business and such business’s continuity. To achieve the objective, following tasks were resolved: concepts of startup business and the startup company were purified, specifics inconcept’s application in the context of the parties were defined; systematized the startup business success factors and ways of strengthening them, focusing on the factors relevant for strengthening economic ties between Lithuania and Sweden within the perspective of IT startup company’s development. Systematic method of research was applied.